Solubility behaviour of antimony(III) and antimony(V) solids in basic aqueous solutions at 300oC

International Nuclear Information System (INIS)

Lemire, R.J.; Tosello, N.B.; Halliday, J.D.

1999-12-01

The major contributions of the isotopes 122 Sb and 124 Sb to activity transport in a CANDU reactor primary heat transport system (HTS), have been associated with oxygen ingress during reactor shutdown. As part of a program to minimize the release and redeposition of these isotopes, the solubilities of antimony(III) and (V) oxides and salts have been measured in basic solutions at temperatures from 25 to 300 o C. The results provide information on the charge and the stability as a function of temperature of antimony solution species and, hence, a guide to the trends in the temperature dependence of the solubilities of antimony solids. In solutions in which oxidation of antimony(III) to antimony(V) is minimized, the solubility of Sb 2 O 3 increases by about two orders of magnitude between 25 and 200 o C, and then levels out or decreases slightly. At 250 o C, in oxidizing solutions, Sb 2 O 5 ·xH 2 O and simple sodium antimonate(V) were found to be unstable in sodium hydroxide solutions with respect to the solid, Na 2α [H(H 2 O)] 2-2α Sb 2 O 6 , which has a pyrochlore structure. The solubility of this partially protonated sodium antimonate increases from 25 to 200 o C and decreases at temperatures above 250 o C. These solubility changes for the antimony (V) solids reflect changes in the stability of the anionic antimony solution species (SbO 3 - or Sb(OH) 6 - ), even though the compositions of antimony-containing solids in basic oxidizing solutions are strongly dependent on the cations and their aqueous phase concentrations. All solids used in the present experiments would be expected to generate total solution antimony concentrations ≥ 0.00005 mol·dm -3 in any neutral or basic aqueous solutions (assuming no added sodium salts). Therefore, under HTS conditions, precipitation of any antimony oxides or mixed oxides is unlikely. It cannot be ruled out that hydrated Sb 2 O 5 (especially the pyrochlore form) might be less soluble in near-neutral, low

Crosslinked hydrogels—a promising class of insoluble solid molecular dispersion carriers for enhancing the delivery of poorly soluble drugs

Directory of Open Access Journals (Sweden)

Dajun D. Sun

2014-02-01

Full Text Available Water-insoluble materials containing amorphous solid dispersions (ASD are an emerging category of drug carriers which can effectively improve dissolution kinetics and kinetic solubility of poorly soluble drugs. ASDs based on water-insoluble crosslinked hydrogels have unique features in contrast to those based on conventional water-soluble and water-insoluble carriers. For example, solid molecular dispersions of poorly soluble drugs in poly(2-hydroxyethyl methacrylate (PHEMA can maintain a high level of supersaturation over a prolonged period of time via a feedback-controlled diffusion mechanism thus avoiding the initial surge of supersaturation followed by a sharp decline in drug concentration typically encountered with ASDs based on water-soluble polymers. The creation of both immediate- and controlled-release ASD dosage forms is also achievable with the PHEMA based hydrogels. So far, ASD systems based on glassy PHEMA have been shown to be very effective in retarding precipitation of amorphous drugs in the solid state to achieve a robust physical stability. This review summarizes recent research efforts in investigating the potential of developing crosslinked PHEMA hydrogels as a promising alternative to conventional water-soluble ASD carriers, and a related finding that the rate of supersaturation generation does affect the kinetic solubility profiles implications to hydrogel based ASDs.

Crosslinked hydrogels-a promising class of insoluble solid molecular dispersion carriers for enhancing the delivery of poorly soluble drugs.

Science.gov (United States)

Sun, Dajun D; Lee, Ping I

2014-02-01

Water-insoluble materials containing amorphous solid dispersions (ASD) are an emerging category of drug carriers which can effectively improve dissolution kinetics and kinetic solubility of poorly soluble drugs. ASDs based on water-insoluble crosslinked hydrogels have unique features in contrast to those based on conventional water-soluble and water-insoluble carriers. For example, solid molecular dispersions of poorly soluble drugs in poly(2-hydroxyethyl methacrylate) (PHEMA) can maintain a high level of supersaturation over a prolonged period of time via a feedback-controlled diffusion mechanism thus avoiding the initial surge of supersaturation followed by a sharp decline in drug concentration typically encountered with ASDs based on water-soluble polymers. The creation of both immediate- and controlled-release ASD dosage forms is also achievable with the PHEMA based hydrogels. So far, ASD systems based on glassy PHEMA have been shown to be very effective in retarding precipitation of amorphous drugs in the solid state to achieve a robust physical stability. This review summarizes recent research efforts in investigating the potential of developing crosslinked PHEMA hydrogels as a promising alternative to conventional water-soluble ASD carriers, and a related finding that the rate of supersaturation generation does affect the kinetic solubility profiles implications to hydrogel based ASDs.

Development of solid dispersion systems of dapivirine to enhance its solubility.

Science.gov (United States)

Gorajana, Adinarayana; Ying, Chan Chiew; Shuang, Yeen; Fong, Pooi; Tan, Zhi; Gupta, Jyoti; Talekar, Meghna; Sharma, Manisha; Garg, Sanjay

2013-06-01

Dapivirine, formerly known as TMC 120, is a poorly-water soluble anti-HIV drug, currently being developed as a vaginal microbicide. The clinical use of this drug has been limited due to its poor solubility. The aim of this study was to design solid dispersion systems of Dapivirine to improve its solubility. Solid dispersions were prepared by solvent and fusion methods. Dapivirine release from the solid dispersion system was determined by conducting in-vitro dissolution studies. The physicochemical characteristics of the drug and its formulation were studied using Differential Scanning Calorimetry (DSC), powder X-ray Diffraction (XRD), Fourier-transform Infrared Spectroscopy (FTIR) and Scanning Electron Microscopy (SEM). A significant improvement in drug dissolution rate was observed with the solid dispersion systems. XRD, SEM and DSC results indicated the transformation of pure Dapivirine which exists in crystalline form into an amorphous form in selected solid dispersion formulations. FTIR and HPLC analysis confirmed the absence of drug-excipient interactions. Solid dispersion systems can be used to improve the dissolution rate of Dapivirine. This improvement could be attributed to the reduction or absence of drug crystallinity, existence of drug particles in an amorphous form and improved wettability of the drug.

Solubility behaviour of antimony(III) and antimony(V) solids in basic aqueous solutions at 300{sup o}C

Energy Technology Data Exchange (ETDEWEB)

Lemire, R.J.; Tosello, N.B.; Halliday, J.D

1999-12-01

The major contributions of the isotopes {sup 122}Sb and {sup 124}Sb to activity transport in a CANDU reactor primary heat transport system (HTS), have been associated with oxygen ingress during reactor shutdown. As part of a program to minimize the release and redeposition of these isotopes, the solubilities of antimony(III) and (V) oxides and salts have been measured in basic solutions at temperatures from 25 to 300{sup o}C. The results provide information on the charge and the stability as a function of temperature of antimony solution species and, hence, a guide to the trends in the temperature dependence of the solubilities of antimony solids. In solutions in which oxidation of antimony(III) to antimony(V) is minimized, the solubility of Sb{sub 2}O{sub 3} increases by about two orders of magnitude between 25 and 200{sup o}C, and then levels out or decreases slightly. At 250{sup o}C, in oxidizing solutions, Sb{sub 2}O{sub 5}{center_dot}xH{sub 2}O and simple sodium antimonate(V) were found to be unstable in sodium hydroxide solutions with respect to the solid, Na{sub 2{alpha}}[H(H{sub 2}O)]{sub 2-2{alpha}}Sb{sub 2}O{sub 6}, which has a pyrochlore structure. The solubility of this partially protonated sodium antimonate increases from 25 to 200{sup o}C and decreases at temperatures above 250{sup o}C. These solubility changes for the antimony (V) solids reflect changes in the stability of the anionic antimony solution species (SbO{sub 3}{sup -} or Sb(OH){sub 6}{sup -}), even though the compositions of antimony-containing solids in basic oxidizing solutions are strongly dependent on the cations and their aqueous phase concentrations. All solids used in the present experiments would be expected to generate total solution antimony concentrations {>=} 0.00005 mol{center_dot}dm{sup -3} in any neutral or basic aqueous solutions (assuming no added sodium salts). Therefore, under HTS conditions, precipitation of any antimony oxides or mixed oxides is unlikely. It cannot be

Method for measurement of radon diffusion and solubility in solid materials

Science.gov (United States)

Maier, Andreas; Weber, Uli; Dickmann, Jannis; Breckow, Joachim; van Beek, Patrick; Schardt, Dieter; Kraft, Gerhard; Fournier, Claudia

2018-02-01

In order to study the permeation i.e. the diffusion and solubility of radon gas in biological material, a new setup was constructed and a novel analysis was applied to obtain diffusion and solubility coefficients. Thin slabs of solid materials were installed between detector housing and the surrounding radon exposure chamber of 50 Ls volume. In this setup radon can diffuse through thin test samples into a cylindrical volume of 5 mm height and 20 mm diameter and reach an α-particle detector. There the 5.49 MeV α-decay of the penetrating radon atoms is measured by a silicon surface barrier detector. The time dependent activities inside the small detector volume are recorded after injection of a known radon activity concentration into the outer chamber. Analyzing the time behavior of the integral α-activity from radon in the small vessel, both, the diffusion coefficient and solubility of the test material can be determined, based on a new mathematical model of the diffusion process concerning the special boundary conditions given by the experimental setup. These first measurements were intended as proof of concept for the detection system and the data analysis. Thin polyethylene foils (LDPE) were selected as material for the diffusion measurements and the results were in agreement with data from literature. In further measurements, we will concentrate on biological material like bone, fat and other tissues.

Solubility enhancement of BCS Class II drug by solid phospholipid dispersions: Spray drying versus freeze-drying.

Science.gov (United States)

Fong, Sophia Yui Kau; Ibisogly, Asiye; Bauer-Brandl, Annette

2015-12-30

The poor aqueous solubility of BCS Class II drugs represents a major challenge for oral dosage form development. Using celecoxib (CXB) as model drug, the current study adopted a novel solid phospholipid nanoparticle (SPLN) approach and compared the effect of two commonly used industrial manufacturing methods, spray- and freeze-drying, on the solubility and dissolution enhancement of CXB. CXB was formulated with Phospholipoid E80 (PL) and trehalose at different CXB:PL:trehalose ratios, of which 1:10:16 was the optimal formulation. Spherical amorphous SPLNs with average diameters <1μm were produced by spray-drying; while amorphous 'matrix'-like structures of solid PL dispersion with larger particle sizes were prepared by freeze-drying. Formulations from both methods significantly enhanced the dissolution rates, apparent solubility, and molecularly dissolved concentration of CXB in phosphate buffer (PBS, pH 6.5) and in biorelevant fasted state simulated intestinal fluid (FaSSIF, pH 6.5) (p<0.05). While similar dissolution rates were found, the spray-dried SPLNs had a larger enhancement in apparent solubility (29- to 132-fold) as well as molecular solubility (18-fold) of CXB at equilibrium (p<0.05). The strong capability of the spray-dried SPLNs to attain 'true' supersaturation state makes them a promising approach for bioavailability enhancement of poorly soluble drugs. Copyright © 2015 Elsevier B.V. All rights reserved.

Fundamental aspects of solid dispersion technology for poorly soluble drugs

Directory of Open Access Journals (Sweden)

Yanbin Huang

2014-02-01

Full Text Available The solid dispersion has become an established solubilization technology for poorly water soluble drugs. Since a solid dispersion is basically a drug–polymer two-component system, the drug–polymer interaction is the determining factor in its design and performance. In this review, we summarize our current understanding of solid dispersions both in the solid state and in dissolution, emphasizing the fundamental aspects of this important technology.

Development of a solid self-microemulsifying drug delivery system (SMEDDS) for solubility enhancement of naproxen.

Science.gov (United States)

Čerpnjak, Katja; Zvonar, Alenka; Vrečer, Franc; Gašperlin, Mirjana

2015-01-01

Comparative evaluation of liquid and solid self-microemulsifying drug delivery systems (SMEDDS) as promising approaches for solubility enhancement. The aim of this work was to develop, characterize, and evaluate a solid SMEDDS prepared via spray-drying of a liquid SMEDDS based on Gelucire® 44/14 to improve the solubility and dissolution rate of naproxen. Various oils and co-surfactants in combination with Gelucire® 44/14 were evaluated during excipient selection study, solubility testing, and construction of (pseudo)ternary diagrams. The selected system was further evaluated for naproxen solubility, self-microemulsification ability, and in vitro dissolution of naproxen. In addition, its transformation into a solid SMEDDS by spray-drying using maltodextrin as a solid carrier was performed. Scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and X-ray diffraction (XRD) were used to evaluate the physical characteristics of the solid SMEDDS obtained. The selected formulation of SMEDDS was comprised of Miglyol 812®, Peceol™, Gelucire® 44/14, and Solutol® HS 15. The liquid and solid SMEDDS formed a microemulsion after dilution with comparable average droplet size and exhibited uniform droplet size distribution. In the solid SMEDDS, liquid SMEDDS was adsorbed onto the surface of maltodextrin and formed smooth granular particles with the encapsulated drug predominantly in a dissolved state and partially in an amorphous state. Overall, incorporation of naproxen in SMEDDS, either liquid or solid, resulted in improved solubility and dissolution rate compared to pure naproxen. This study indicates that a liquid and solid SMEDDS is a strategy for solubility enhancement in the future development of orally delivered dosage forms.

Enhancement of carvedilol solubility by solid dispersion technique using cyclodextrins, water soluble polymers and hydroxyl acid.

Science.gov (United States)

Yuvaraja, K; Khanam, Jasmina

2014-08-05

Aim of the present work is to enhance aqueous solubility of carvedilol (CV) by solid dispersion technique using wide variety of carriers such as: β-cyclodextrin (βCD), hydroxypropyl-β-cyclodextrin (HPβCD), tartaric acid (TA), polyvinyl pyrrolidone K-30 (PVP K-30) and poloxamer-407 (PLX-407). Various products of 'CV-solid dispersion' had been studied extensively in various pH conditions to check enhancement of solubility and dissolution characteristics of carvedilol. Any physical change upon interaction between CV and carriers was confirmed by instrumental analysis: XRD, DSC, FTIR and SEM. Negative change of Gibb's free energy and complexation constants (Kc, 75-240M(-1), for cyclodextrins and 1111-20,365M(-1), for PVP K-30 and PLX-407) were the evidence of stable nature of the binding between CV and carriers. 'Solubility enhancement factor' of ionized-CV was found high enough (340 times) with HPβCD in presence of TA. TA increases the binding efficiency of cyclodextrin and changing the pH of microenvironment in dissolution medium. In addition, ionization process was used to increase the apparent intrinsic solubility of drug. In vitro, dissolution time of CV was remarkably reduced in the solid dispersion system compared to that of pure drug. This may be attributed to increased wettability, dispersing ability and transformation of crystalline state of drug to amorphous one. Copyright © 2014 Elsevier B.V. All rights reserved.

Determination of the solubility limiting solid of the selenium in the presence of iron under anoxic conditions

International Nuclear Information System (INIS)

Iida, Y.; Yamaguchi, T.; Tanaka, T.; Kitamura, A.; Nakayama, S.

2009-01-01

Dissolution experiments of selenium were performed from both under saturation and over saturation directions to determine the solubility limiting solid of selenium under the conditions which thermodynamically prefer the formation of ferroselite (FeSe 2 ). X-ray diffractometry (XRD) showed that FeSe 2 was formed in the over-saturation experiments. However, the ion activity products for the reaction of 0.5 FeSe 2 + H + + e - 0.5 Fe 2+ + HSe - , aFe 2+0.5 aHSe - a H+ -1 a e- -1 , obtained from both under saturation and over saturation directions were 3 to 4 orders of magnitude higher than the equilibrium constants calculated from existing thermodynamic data. The dependencies of the selenium concentration on pH, Eh and the iron concentration were better interpreted as a dissolution reaction of selenium solid (Se(s)) than the iron-selenium compounds. The equilibrium constant of: Se(s) + H + + 2e - = HSe - was determined to be logK 0 -7.46±0.11. This value agrees with the value of logK 0 = -7.62±0.06 calculated from existing thermodynamic data of crystalline selenium within errors. Because crystalline selenium was not identified in the solid phases by XRD, the solubility limiting solid would be amorphous or minor amount of crystalline selenium, even if the iron-selenium compound was formed. (authors)

The mechanisms of drug release from solid dispersions in water-soluble polymers.

Science.gov (United States)

Craig, Duncan Q M

2002-01-14

Solid dispersions in water-soluble carriers have attracted considerable interest as a means of improving the dissolution rate, and hence possibly bioavailability, of a range of hydrophobic drugs. However, despite the publication of numerous original papers and reviews on the subject, the mechanisms underpinning the observed improvements in dissolution rate are not yet understood. In this review the current consensus with regard to the solid-state structure and dissolution properties of solid dispersions is critically assessed. In particular the theories of carrier- and drug-controlled dissolution are highlighted. A model is proposed whereby the release behaviour from the dispersions may be understood in terms of the dissolution or otherwise of the drug into the concentrated aqueous polymer layer adjacent to the solid surface, including a derivation of an expression to describe the release of intact particles from the dispersions. The implications of a deeper understanding of the dissolution mechanisms are discussed, with particular emphasis on optimising the choice of carrier and manufacturing method and the prediction of stability problems.

Solubilities of some hydrous REE phosphates with implications for diagenesis and sea water concentrations

International Nuclear Information System (INIS)

Jonasson, R.G.; Bancroft, G.M.; Nesbitt, H.W.

1985-01-01

Solubility product determinations suggest that the hydrous phosphates of the rare earths, REPO 4 .xH 2 O, are important in controlling the sea water REE concentrations. Two of these solids, rhabdophane, (P6 2 22) and 'hydrous xenotime', (I4 1 /amd), have been synthesized at 100 C via the acid hydrolysis of the respective REE pyrophosphate. The solubility products at infinite dilution were determined to be pK 0 = 24.5, (La at 25 C); 26.0, (Pr at 100 C); 25.7, (Nd at 100 C); and 25.5, (Er at 100 C). On the basis of calculations involving the reaction of Re 3+ with apatite to form the hydrous phosphate, the lanthanum concentration in sea water is predicted to be about 140 pmol/L. Laboratory experiments support the hypothesis that apatite is a substrate for reactions with dissolved REE. (author)

Method for Predicting Solubilities of Solids in Mixed Solvents

DEFF Research Database (Denmark)

Ellegaard, Martin Dela; Abildskov, Jens; O'Connell, J. P.

2009-01-01

A method is presented for predicting solubilities of solid solutes in mixed solvents, based on excess Henry's law constants. The basis is statistical mechanical fluctuation solution theory for composition derivatives of solute/solvent infinite dilution activity coefficients. Suitable approximatio...

Assessment of hupu gum for its carrier property in the design and evaluation of solid mixtures of poorly water soluble drug - rofecoxib.

Science.gov (United States)

Vadlamudi, Harini Chowdary; Raju, Y Prasanna; Asuntha, G; Nair, Rahul; Murthy, K V Ramana; Vulava, Jayasri

2014-01-01

There are no reports about the pharmaceutical applications of hupu gum (HG). Hence the present study was undertaken to test its suitability in the dissolution enhancement of poorly water soluble drug. Rofecoxib (RFB) was taken as model drug. For comparison solid mixtures were prepared with carriers such as poly vinyl pyrrolidone (PVP), sodium starch glycollate (SSG) and guar gum (GG). Physical mixing (PM), co-grinding (CG), kneading (KT) and solvent evaporation (SE) techniques were used to prepare the solid mixtures, using all the carriers in different carrier and drug ratios. The solid mixtures were characterized by powder X-ray diffraction (XRD) and Fourier-transformed infrared spectroscopy (FTIR). There was a significant improvement in the dissolution rate of solid mixtures of HG, when compared with the solid mixtures of other carriers. There was an increase in dissolution rate with increase in concentration of HG upto 1:1 ratio of carrier and drug. No drug-carrier interaction was found by FTIR studies. XRD studies indicated reduction in crystallinity of the drug with increase in HG concentration. Hence HG could be a useful carrier for the dissolution enhancement of poorly water soluble drugs.

Eutectic, monotectic and immiscibility systems of nimesulide with water-soluble carriers: phase equilibria, solid-state characterisation and in-vivo/pharmacodynamic evaluation.

Science.gov (United States)

Abdelkader, Hamdy; Abdallah, Ossama Y; Salem, Hesham; Alani, Adam W G; Alany, Raid G

2014-10-01

The solid-state interactions of fused mixtures nimesulide (ND) with polyethylene glycol (PEG) 4000, urea or mannitol were studied through constructing thaw-melt phase equilibrium diagrams. The solid-state characteristics were investigated using differential scanning calorimetry (DSC) and X-ray diffraction (XRD). Various types of interactions were identified such as the formation of a eutectic system of ND-PEG 4000, monotectic system of ND-urea and complete solid immiscibility of ND with mannitol. The effects of carrier concentrations on the equilibrium solubility and in-vitro dissolution characteristics were studied. Linear increases (R(2)  > 0.99) in the aqueous solubility of ND in various concentrations of PEG 4000 and urea were obtained, whereas mannitol did not exhibit any effect on the solubility of ND. Similar trends were obtained with the dissolution efficiency of the fused mixtures of ND with PEG 4000 and urea compared with the corresponding physical mixtures and untreated drug. The analgesic effects of untreated ND and the selected formulations were investigated by evaluating the drug's ability to inhibit the acetic acid-induced writhing response. The analgesic effect of ND in a eutectic mixture with PEG 4000 and a monotectic mixture with urea was potentiated by 3.2 and 2.7-fold respectively compared with the untreated drug. © 2014 Royal Pharmaceutical Society.

Preparation of amorphous solid dispersions by rotary evaporation and KinetiSol Dispersing: approaches to enhance solubility of a poorly water-soluble gum extract.

Science.gov (United States)

Bennett, Ryan C; Brough, Chris; Miller, Dave A; O'Donnell, Kevin P; Keen, Justin M; Hughey, Justin R; Williams, Robert O; McGinity, James W

2015-03-01

Acetyl-11-keto-β-boswellic acid (AKBA), a gum resin extract, possesses poor water-solubility that limits bioavailability and a high melting point making it difficult to successfully process into solid dispersions by fusion methods. The purpose of this study was to investigate solvent and thermal processing techniques for the preparation of amorphous solid dispersions (ASDs) exhibiting enhanced solubility, dissolution rates and bioavailability. Solid dispersions were successfully produced by rotary evaporation (RE) and KinetiSol® Dispersing (KSD). Solid state and chemical characterization revealed that ASD with good potency and purity were produced by both RE and KSD. Results of the RE studies demonstrated that AQOAT®-LF, AQOAT®-MF, Eudragit® L100-55 and Soluplus with the incorporation of dioctyl sulfosuccinate sodium provided substantial solubility enhancement. Non-sink dissolution analysis showed enhanced dissolution properties for KSD-processed solid dispersions in comparison to RE-processed solid dispersions. Variances in release performance were identified when different particle size fractions of KSD samples were analyzed. Selected RE samples varying in particle surface morphologies were placed under storage and exhibited crystalline growth following solid-state stability analysis at 12 months in comparison to stored KSD samples confirming amorphous instability for RE products. In vivo analysis of KSD-processed solid dispersions revealed significantly enhanced AKBA absorption in comparison to the neat, active substance.

Pure Phase Solubility Limits: LANL

International Nuclear Information System (INIS)

C. Stockman

2001-01-01

The natural and engineered system at Yucca Mountain (YM) defines the site-specific conditions under which one must determine to what extent the engineered and the natural geochemical barriers will prevent the release of radioactive material from the repository. Most important mechanisms for retention or enhancement of radionuclide transport include precipitation or co-precipitation of radionuclide-bearing solid phases (solubility limits), complexation in solution, sorption onto surfaces, colloid formation, and diffusion. There may be many scenarios that could affect the near-field environment, creating chemical conditions more aggressive than the conditions presented by the unperturbed system (such as pH changes beyond the range of 6 to 9 or significant changes in the ionic strength of infiltrated waters). For an extended period of time, the near-field water composition may be quite different and more extreme in pH, ionic strength, and CO 2 partial pressure (or carbonate concentration) than waters at some distance from the repository. Reducing conditions, high pH (up to 11), and low carbonate concentration may be present in the near-field after reaction of infiltrating groundwater with engineered barrier systems, such as cementitious materials. In the far-field, conditions are controlled by the rock-mass buffer providing a near-neutral, oxidizing, low-ionic-strength environment that controls radionuclide solubility limits and sorption capacities. There is the need for characterization of variable chemical conditions that affect solubility, speciation, and sorption reactions. Modeling of the groundwater chemistry is required and leads to an understanding of solubility and speciation of the important radionuclides. Because experimental studies cannot be performed under the numerous potential chemical conditions, solubility limitations must rely on geochemical modeling of the radionuclide's chemistry. Fundamental thermodynamic properties, such as solubility products

Pure Phase Solubility Limits: LANL

Energy Technology Data Exchange (ETDEWEB)

C. Stockman

2001-01-26

The natural and engineered system at Yucca Mountain (YM) defines the site-specific conditions under which one must determine to what extent the engineered and the natural geochemical barriers will prevent the release of radioactive material from the repository. Most important mechanisms for retention or enhancement of radionuclide transport include precipitation or co-precipitation of radionuclide-bearing solid phases (solubility limits), complexation in solution, sorption onto surfaces, colloid formation, and diffusion. There may be many scenarios that could affect the near-field environment, creating chemical conditions more aggressive than the conditions presented by the unperturbed system (such as pH changes beyond the range of 6 to 9 or significant changes in the ionic strength of infiltrated waters). For an extended period of time, the near-field water composition may be quite different and more extreme in pH, ionic strength, and CO{sub 2} partial pressure (or carbonate concentration) than waters at some distance from the repository. Reducing conditions, high pH (up to 11), and low carbonate concentration may be present in the near-field after reaction of infiltrating groundwater with engineered barrier systems, such as cementitious materials. In the far-field, conditions are controlled by the rock-mass buffer providing a near-neutral, oxidizing, low-ionic-strength environment that controls radionuclide solubility limits and sorption capacities. There is the need for characterization of variable chemical conditions that affect solubility, speciation, and sorption reactions. Modeling of the groundwater chemistry is required and leads to an understanding of solubility and speciation of the important radionuclides. Because experimental studies cannot be performed under the numerous potential chemical conditions, solubility limitations must rely on geochemical modeling of the radionuclide's chemistry. Fundamental thermodynamic properties, such as solubility

Studies on Dissolution Enhancement of Prednisolone, a Poorly Water-Soluble Drug by Solid Dispersion Technique

Directory of Open Access Journals (Sweden)

Parvin Zakeri-Milani

2011-06-01

Full Text Available Introduction: Prednisolone is a class II substance according to the Biopharmaceutics Classification System. It is a poorly water soluble agent. The aim of the present study was to improve dissolution rate of a poorly water-soluble drug, prednisolone, by a solid dispersion technique. Methods: Solid dispersion of prednisolone was prepared with PEG 6000 or different carbohydrates such as lactose and dextrin with various ratios of the drug to carrier i.e., 1:10, 1:20 and 1:40. Solid dispersions were prepared by coevaporation method. The evaluation of the properties of the dispersions was performed using dissolution studies, Fourier-transform infrared spectroscopy and x-ray powder diffractometery. Results: The results indicated that lactose is suitable carriers to enhance the in vitro dissolution rate of prednisolone. The data from the x-ray diffraction showed that the drug was still detectable in its solid state in all solid dispersions except solid dispersions prepared by dextrin as carrier. The results from infrared spectroscopy showed no well-defined drug–carrier interactions for coevaporates. Conclusion: Solid dispersion of a poorly water-soluble drug, prednisolone may alleviate the problems of delayed and inconsistent rate of dissolution of the drug.

Peculiarities of hydrogen permeation through Zr–1%Nb alloy and evaluation of terminal solid solubility

Energy Technology Data Exchange (ETDEWEB)

Denisov, E.A.; Kompaniets, M.V.; Kompaniets, T.N., E-mail: tkompaniets@spbu.ru; Bobkova, I.S.

2016-04-15

Hydrogen permeation through Zr–1%Nb alloy was studied at the temperature below the temperature of α-β transition. Analysis of the transient permeation curves from a closed volume in a surface limited regime allowed to determine total and mobile hydrogen concentrations. At the mobile hydrogen concentration of 4.3 at% a part of the absorbed hydrogen is cut out of permeation process. Increase of the mobile hydrogen concentration in α-phase of Zr–1%Nb alloy is ceasing at the concentration of (5.5 ± 0.3) at%, which is the maximum possible concentration of the mobile hydrogen in α-phase of the studied alloy. From this moment on all absorbed hydrogen is spent on hydride formation. The obtained results are compared with those obtained by means of traditional techniques for terminal solid solubility determination.

Effects of Spray-Drying and Choice of Solid Carriers on Concentrations of Labrasol® and Transcutol® in Solid Self-Microemulsifying Drug Delivery Systems (SMEDDS

Directory of Open Access Journals (Sweden)

Christopher Wai-Kei Lam

2013-01-01

Full Text Available Solid self-microemulsifying drug delivery systems (SMEDDS have been used increasingly for improving the bioavailability of hydrophobic drugs. Labrasol® and Transcutol® are used widely as surfactant and solubilizer in the formulation of solid SMEDDS. We investigated the effects of spray-drying and the use of different solid carriers on concentrations of Labrasol® and Transcutol® in solid SMEDDS with scutellarin as the formulated drug. Liquid and gas chromatography tandem mass spectrometry (LC-MS and GC-MS methods were developed for measuring low concentrations of Labrasol® and Transcutol®. In the preparation of solid SMEDDS, lactose, hydroxypropylmethyl cellulose (HPMC and microcrystalline cellulose (MCC were used as solid carriers. Judging from the retention ratios of Labrasol® and Transcutol®, the droplet size of solid SMEDDS increased after spray-drying of liquid SMEDDS, and concentrations of these excipients decreased after the solidifying procedure. In such reduction, Lactose and HPMC were found to preserve Labrasol® and Transcutol® better than MCC during spray-drying, and the resultant droplet sizes were smaller than that of MCC. Labrasol® and Transcutol® showed good thermal stability at 60 °C degree for 10 days. It can be concluded that spray-drying could increase the droplet size of solid SMEDDS and decreased the concentration of Labrasol® and Transcutol® therein, while water-soluble solid carriers could preserve Labrasol® and Transcutol® better than insoluble carriers in the solid SMEDDS.

Crosslinked hydrogels?a promising class of insoluble solid molecular dispersion carriers for enhancing the delivery of poorly soluble drugs

OpenAIRE

Sun, Dajun D.; Lee, Ping I.

2014-01-01

Water-insoluble materials containing amorphous solid dispersions (ASD) are an emerging category of drug carriers which can effectively improve dissolution kinetics and kinetic solubility of poorly soluble drugs. ASDs based on water-insoluble crosslinked hydrogels have unique features in contrast to those based on conventional water-soluble and water-insoluble carriers. For example, solid molecular dispersions of poorly soluble drugs in poly(2-hydroxyethyl methacrylate) (PHEMA) can maintain a ...

Solubilization of poorly water-soluble drugs using solid dispersions.

Science.gov (United States)

Tran, Thao T-D; Tran, Phuong H-L; Khanh, Tran N; Van, Toi V; Lee, Beom-Jin

2013-08-01

Many new drugs have been discovered in pharmaceutical industry and exposed their surprised potential therapeutic effects. Unfortunately, these drugs possess low absorption and bioavailability since their solubility limitation in water. Solid dispersion (SD) is the current technique gaining so many attractions from scientists due to its effect on improving solubility and dissolution rate of poorly water-soluble drugs. A number of patents including the most recent inventions have been undertaken in this review to address various respects of this strategy in solubilization of poorly watersoluble drugs including type of carriers, preparation methods and view of technologies used to detect SD properties and mechanisms with the aim to accomplish a SD not only effective on enhanced bioavailability but also overcome difficulties associated with stability and production. Future prospects are as well discussed with an only hope that many developments and researches in this field will be successfully reached and contributed to commercial use for treatment as much as possible.

Robust model of fresh jujube soluble solids content with near ...

African Journals Online (AJOL)

A robust partial least square (PLS) calibration model with high accuracy and stability was established for the measurement of soluble solids content (SSC) of fresh jujube using near-infrared (NIR) spectroscopy technique. Fresh jujube samples were collected in different areas of Taigu and Taiyuan cities, central China in ...

Encapsulation of solid dispersion in solid lipid particles for dissolution enhancement of poorly water-soluble drug.

Science.gov (United States)

Tran, Khanh Thi My; Vo, Toi Van; Tran, Phuong Ha-Lien; Lee, Beom-Jin; Duan, Wei; Tran, Thao Truong-Dinh

2017-06-05

The aim of this research was to engineer solid dispersion lipid particles (SD-SLs) in which a solid dispersion (SD) was encapsulated to form the core of solid lipid particles (SLs), thereby achieving an efficient enhancement in the dissolution of a poorly water-soluble drug. Ultrasonication was introduced into the process to obtain micro/nanoscale SLs. The mechanism of dissolution enhancement was investigated by analysing the crystalline structure, molecular interactions, and particle size of the formulations. The drug release from the SD-SLs was significantly greater than that from the SD or SLs alone. This enhancement in drug release was dependent on the preparation method and the drug-to-polymer ratio of the SD. With an appropriate amount of polymer in the SD, the solidification method had the potential to alter the drug crystallinity to an amorphous state, resulting in particle uniformity and molecular interactions in the SD-SLs. The proposed system provides a new strategy for enhancing the dissolution rate of poorly water-soluble drugs and further improving their bioavailability. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Solubility of NaNd(CO3)2.6H2O(c) in concentrated Na2CO3 and NaHCO3 solutions

International Nuclear Information System (INIS)

Rao, L.; Rai, D.; Felmy, A.R.; Fulton, R.W.; Novak, C.F.

1996-01-01

NaNd(CO 3 ) 2 x 6 H 2 O(c) was identified to be the final equilibrium solid phase in suspensions containing concentrated sodium carbonate (0.1 to 2.0 M) and sodium bicarbonate (0.1 to 1.0 M), with either NaNd(CO 3 ) 2 x 6 H 2 O(c) or Nd 2 (CO 3 ) 3 x xH 2 O(s) as initial solids. A thermodynamic model, based on Pitzer's specific into-interaction approach, was developed to interpret the solubility of NaNd(CO 3 ) 2 x 6 H 2 O(c) as functions of sodium carbonate and sodium bicarbonate concentrations. In this model, the solubility data of NaNd(CO 3 ) 2 x 6 H 2 O(c) were explained by assuming the formation of NdCO 3 + , Nd(CO 3 ) 2 - and Nd(CO 3 ) 3 3- species and invoking the specific ion interactions between Na + and Nd(CO 3 ) 3 3- . Ion interaction parameters for Na + -Nd(CO 3 ) 3 3- were developed to fit the solubility data. Based on the model calculations, Nd(CO 3 ) 3 3- was the predominant aqueous neodymium species in 0.1 to 2 M sodium carbonate and 0.1 to 1 M sodium bicarbonate solutions. The logarithm of the NaNd(CO 3 ) 2 x 6 H 2 O solubility product (NaNd(CO 3 ) 2 x 6 H 2 O(c)=Na + +Nd 3+ +2 CO 3 2- +6 H 2 O) was calculated to be -21.39. This model also provided satisfactory interpretation of the solubility data of the analogous Am(III) system in less concentrated carbonate and bicarbonate solutions. (orig.)

Solubility of ferrocyanide compounds. Ferrocyanide Safety Project, Interim report FY1994

International Nuclear Information System (INIS)

Rai, D.; Felmy, A.R.; Smith, S.C.; Ryan, J.L.

1994-10-01

The solubility of Cs 2 NiFe(CN) 6 (c) [1] as a function of NaOH and temperature was determined to ascertain whether [1] shows retrograde solubility (i.e., decreasing solubility with increasing temperature), which would have bearing on the possible formation of ''hot spots'' in the tanks and thus the safety of the ferrocyanide tanks. The results show that the aqueous concentrations of Cs in equilibrium with [1] at 25, 60, 75 and 90 C are similar (within the limits of experimental error), indicating that [1] does not show retrograde solubility. To understand general solubility relationships of Ni 2 Fe(CN) 6 (c) [2] and to determine the influence on solubility of high electrolyte concentrations (e.g., NaNO 3 ) that are commonly encountered in the ferrocyanide tanks, the solubility of [2] as a function of CsNO 3 , NiCl 2 , and NaNO 3 was determined. In general, [2] is fairly insoluble and shows slightly increased solubility at high electrolyte concentrations only. For [2] in NiCl 2 , the aqueous Fe concentrations show first a decrease and then an increase with the increase in NiCl 2 concentrations. The increase in Fe concentrations at high Ni concentrations appears to be the result of replacement of Fe by Ni in the [2] structure. For [2] in CsNO 3 and at 0.001 M Na 4 Fe(CN) 6 , the Cs is quantitatively removed from solution at low added Cs concentrations and appears to approach the final solid composition of [1]. The solubility of [2] in NaNO 3 and at 0.001 M Na 4 Fe(CN) 6 shows an increase in Ni concentrations to about 0.5 mg/l at NaNO 3 concentrations > 1.0 M. These increased Ni concentrations may be the result of substitution of Na for Ni in the solid phase

Dissolution-modulating mechanism of pH modifiers in solid dispersion containing weakly acidic or basic drugs with poor water solubility.

Science.gov (United States)

Tran, Phuong Ha-Lien; Tran, Thao Truong-Dinh; Lee, Kyoung-Ho; Kim, Dong-Jin; Lee, Beom-Jin

2010-05-01

Although the solid dispersion method has been known to increase the dissolution rate of poorly water-soluble drugs by dispersing them in hydrophilic carriers, one obstacle of the solid dispersion method is its limited solubilization capacity, especially for pH-dependent soluble drugs. pH-modified solid dispersion, in which pH modifiers are incorporated, may be a useful method for increasing the dissolution rate of weakly acidic or basic drugs. Sufficient research, including the most recent reports, was undertaken in this review. How could the inclusion of the pH the pH modifiers in the solid dispersion system change drug structural behaviors, molecular interactions, microenvironmental pH, and/or release rate of pH modifiers, relating with the enhanced dissolution of weakly acidic or weakly basic drugs with poor water solubility? These questions have been investigated to determine the dissolution-modulating mechanism of pH modifiers in solid dispersion containing weakly acidic or basic drugs. It is believed that step-by-step mechanistic approaches could provide the ultimate solution for solubilizing several poorly water-soluble drugs with pH-dependent solubility from a solid dispersion system, as well as provide ideas for developing future dosage systems.

Inter-species comparative analysis of components of soluble sugar concentration in fleshy fruits

Directory of Open Access Journals (Sweden)

Zhanwu eDai

2016-05-01

Full Text Available The soluble sugar concentration of fleshy fruit is a key determinant of fleshy fruit quality. It affects directly the sweetness of fresh fruits and indirectly the properties of processed products (e.g. alcohol content in wine. Despite considerable divergence among species, soluble sugar accumulation in a fruit results from the complex interplay of three main processes, namely sugar import, sugar metabolism, and water dilution. Therefore, inter-species comparison would help to identify common and/or species-specific modes of regulation in sugar accumulation. For this purpose, a process-based mathematical framework was used to compare soluble sugar accumulation in three fruits: grape, tomato and peach. Representative datasets covering the time course of sugar accumulation during fruit development were collected. They encompassed 104 combinations of species (3, genotypes (32, and growing conditions (19 years and 16 nutrient and environmental treatments. At maturity, grape showed the highest soluble sugar concentrations (16.5-26.3 g /100 g FW, followed by peach (2.2 to 20 g /100 g FW and tomato (1.4 to 5 g /100 g FW. Main processes determining soluble sugar concentration were decomposed into sugar importation, metabolism and water dilution with the process-based analysis. Different regulation modes of soluble sugar concentration were then identified, showing either import-based, dilution-based, or import and dilution dual-based. Firstly, the higher soluble sugar concentration in grape than in tomato is a result of higher sugar importation. Secondly, the higher soluble sugar concentration in grape than in peach is due to a lower water dilution. The third mode of regulation is more complicated than the first two, with differences both in sugar importation and water dilution (grape vs cherry tomato; cherry tomato vs peach; peach vs tomato. On the other hand, carbon utilization for synthesis of non-soluble sugar compounds (namely metabolism was

Design, optimization and evaluation of glipizide solid self-nanoemulsifying drug delivery for enhanced solubility and dissolution.

Science.gov (United States)

Dash, Rajendra Narayan; Mohammed, Habibuddin; Humaira, Touseef; Ramesh, Devi

2015-10-01

A solid self-nanoemulsifying drug-delivery system (solid SNEDDS) has been explored to improve the solubility and dissolution profile of glipizide. SNEDDS preconcentrate was systematically optimized using a circumscribed central composite design by varying Captex 355 (Oil), Solutol HS15 (Surfactant) and Imwitor 988 (Co-surfactant). The optimized SNEDDS preconcentrate consisted of Captex 355 (30% w/w), Solutol HS15 (45% w/w) and Imwitor 988 (25% w/w). The saturation solubility (SS) of glipizide in optimized SNEDDS preconcentrate was found to be 45.12 ± 1.36 mg/ml, indicating an improvement (1367 times) of glipizide solubility as compared to its aqueous solubility (0.033 ± 0.0021 mg/ml). At 90% SS, glipizide was loaded to the optimized SNEDDS. In-vitro dilution of liquid SNEDDS resulted in a nanoemulsion with a mean droplet size of 29.4 nm. TEM studies of diluted liquid SNEDDS confirmed the uniform shape and size of the globules. The liquid SNEDDS was adsorbed onto calcium carbonate and talc to form solid SNEDDS. PXRD, DSC, and SEM results indicated that, the presence of glipizide as an amorphous and as a molecular dispersion state within solid SNEDDS. Glipizide dissolution improved significantly (p < 0.001) from the solid SNEDDS (∼100% in 15 min) as compared to the pure drug (18.37%) and commercial product (65.82) respectively.

Drug-Drug Multicomponent Solid Forms: Cocrystal, Coamorphous and Eutectic of Three Poorly Soluble Antihypertensive Drugs Using Mechanochemical Approach.

Science.gov (United States)

Haneef, Jamshed; Chadha, Renu

2017-08-01

The present study deals with the application of mechanochemical approach for the preparation of drug-drug multicomponent solid forms of three poorly soluble antihypertensive drugs (telmisartan, irbesartan and hydrochlorothiazide) using atenolol as a coformer. The resultant solid forms comprise of cocrystal (telmisartan-atenolol), coamorphous (irbesartan-atenolol) and eutectic (hydrochlorothiazide-atenolol). The study emphasizes that solid-state transformation of drug molecules into new forms is a result of the change in structural patterns, diminishing of dimers and creating new facile hydrogen bonding network based on structural resemblance. The propensity for heteromeric or homomeric interaction between two different drugs resulted into diverse solid forms (cocrystal/coamorphous/eutectics) and become one of the interesting aspects of this research work. Evaluation of these solid forms revealed an increase in solubility and dissolution leading to better antihypertensive activity in deoxycorticosterone acetate (DOCA) salt-induced animal model. Thus, development of these drug-drug multicomponent solid forms is a promising and viable approach to addressing the issue of poor solubility and could be of considerable interest in dual drug therapy for the treatment of hypertension.

A physiological and genetic approach to the improvement of tomato (Lycopersicon esculentum Mill.) fruit soluble solids

International Nuclear Information System (INIS)

Damon, S.E.

1989-01-01

Physiological processes and the genetic basis determining soluble solids content (SSC) of processing tomato fruit were addressed. Analysis of [ 3 H]-(fructosyl)-sucrose translocation in tomato indicates that phloem unloading in the fruit occurs, at least in part, to the apoplast. Apoplastic sucrose, glucose and fructose concentrations were estimated as 1 to 7, 12 to 49 and 8 to 63 millimolar, respectively in tomato fruit pericarp. Short-term uptake of [ 14 C]sucrose, -glucose and -fructose in tomato pericarp discs showes first order kinetics over the physiologically relevant concentration range. The uptake of [ 14 C]-(glycosyl)-1'fluorosucrose was identical to the rate of [ 14 C] sucrose uptake suggesting sucrose may be taken up directly without prior extracellular hydrolysis. Short-term uptake of all three sugars was insensitive to 10 micromolar carbonyl cyanide m-chlorophenylhydrazone and to 10 micromolar p-chloromercuribenzene sulfonic acid. However, long-term accumulation of glucose was sensitive to carbonyl cyanide m-chlorophenylhydrazone. Sugar uptake across the plasmamembrane does not appear to be energy dependent, suggesting that sugar accumulation in the tomato is driven by subsequent intracellular metabolism and/or active uptake at the tonoplast. Fourteen genomic DNA probes and ten restriction endonucleases were used to identify restriction fragment length polymorphisms (RFLPs) useful in the linkage analysis of quantitative trait loci controlling the expression of SSC in a segregating F 2 population from a cross between L. esculentum (UC204B) and L. cheesmanii f. minor, a wild species with high fruit soluble solids. RFLPs were detected between the DNAs of the two tomato species with all 14 probes

The amorphous solid dispersion of the poorly soluble ABT-102 forms nano/microparticulate structures in aqueous medium: impact on solubility

Directory of Open Access Journals (Sweden)

Frank KJ

2012-11-01

Full Text Available Kerstin J Frank,1,3 Ulrich Westedt,2 Karin M Rosenblatt,2 Peter Hölig,2 Jörg Rosenberg,2 Markus Mägerlein,2 Gert Fricker,3 Martin Brandl11Department of Physics, Chemistry and Pharmacy, University of Southern Denmark, Odense, Denmark; 2Abbott GmbH and Co. KG, Ludwigshafen, Germany; 3Department of Pharmaceutical Technology, University of Heidelberg, Heidelberg, GermanyAbstract: Amorphous solid dispersions (ASDs are a promising formulation approach for poorly soluble active pharmaceutical ingredients (APIs, because they ideally enhance both dissolution rate and solubility. However, the mechanism behind this is not understood in detail. In the present study, we investigated the supramolecular and the nano/microparticulate structures that emerge spontaneously upon dispersion of an ASD in aqueous medium and elucidated their influence on solubility. The ASD, prepared by hot melt extrusion, contained the poorly soluble ABT-102 (solubility in buffer, 0.05 µg/mL, a hydrophilic polymer, and three surfactants. The apparent solubility of ABT-102 from the ASD-formulation was enhanced up to 200 times in comparison to crystalline ABT-102. At the same time, the molecular solubility, as assessed by inverse equilibrium dialysis, was enhanced two times. Asymmetrical flow field-flow fractionation in combination with a multiangle light-scattering detector, an ultraviolet detector, and a refractometer enabled us to separate and identify the various supramolecular assemblies that were present in the aqueous dispersions of the API-free ASD (placebo and of binary/ternary blends of the ingredients. Thus, the supramolecular assemblies with a molar mass between 20,000 and 90,000 could be assigned to the polyvinylpyrrolidone/vinyl acetate 64, while two other kinds of assemblies were assigned to different surfactant assemblies (micelles. The amount of ABT-102 remaining associated with each of the assemblies upon fractionation was quantified offline with high

Crystal-Structure Contribution to the Solid Solubility in Transition Metal Alloys

DEFF Research Database (Denmark)

Ruban, Andrei; Skriver, Hans Lomholt; Nørskov, Jens Kehlet

1998-01-01

The solution energies of 4d metals in other 4d metals as well as the bcc-hcp structural energy differences in random 4d alloys are calculated by density functional theory. It is shown that the crystal structure of the host plays a crucial role in the solid solubility. A local virtual bond...

Solid dispersions in oncology: a solution to solubility-limited oral drug absorption

NARCIS (Netherlands)

Sawicki, Emilia

2017-01-01

This thesis discusses the formulation method solid dispersion and how it works to resolve solubility-limited absorption of orally dosed anticancer drugs. Dissolution in water is essential for drug absorption because only dissolved drug molecules are absorbed. The problem is that half of the arsenal

Solid dispersions enhance solubility, dissolution, and permeability of thalidomide.

Science.gov (United States)

Barea, Silvana A; Mattos, Cristiane B; Cruz, Ariadne C C; Chaves, Vitor C; Pereira, Rafael N; Simões, Claudia M O; Kratz, Jadel M; Koester, Letícia S

2017-03-01

Thalidomide (THD) is a BCS class II drug with renewed and growing therapeutic applicability. Along with the low aqueous solubility, additional poor biopharmaceutical properties of the drug, i.e. chemical instability, high crystallinity, and polymorphism, lead to a slow and variable oral absorption. In this view, we developed solid dispersions (SDs) containing THD dispersed in different self-emulsifying carriers aiming at an enhanced absorption profile for the drug. THD was dispersed in lauroyl macrogol-32 glycerides (Gelucire ® 44/14) and α-tocopherol polyethylene glycol succinate (Kolliphor ® TPGS), in the presence or absence of the precipitation inhibitor polyvinylpyrrolidone K30 (PVP K30), by means of the solvent method. Physicochemical analysis revealed the formation of semicrystalline SDs. X-ray diffraction and infrared spectroscopy analyses suggest that the remaining crystalline fraction of the drug in the SDs did not undergo polymorphic transition. The impact of the solubility-enhancing formulations on the THD biopharmaceutical properties was evaluated by several in vitro techniques. The developed SDs were able to increase the apparent solubility of the drug (up to 2-3x the equilibrium solubility) for a least 4 h. Dissolution experiments (paddle method, 75 rpm) in different pHs showed that around 80% of drug dissolved after 120 min (versus 40% of pure crystalline drug). Additionally, we demonstrated the enhanced solubility obtained via SDs could be translated into increased flux in a parallel artificial membrane permeability assay (PAMPA). In summary, the results demonstrate that SDs could be considered an interesting and unexplored strategy to improve the biopharmaceutical properties of THD, since SDs of this important drug have yet to be reported.

Revealing facts behind spray dried solid dispersion technology used for solubility enhancement

Science.gov (United States)

Patel, Bhavesh B.; Patel, Jayvadan K.; Chakraborty, Subhashis; Shukla, Dali

2013-01-01

Poor solubility and bioavailability of an existing or newly synthesized drug always pose challenge in the development of efficient pharmaceutical formulation. Numerous technologies can be used to improve the solubility and among them amorphous solid dispersion based spray drying technology can be successfully useful for development of product from lab scale to commercial scale with a wide range of powder characteristics. Current review deals with the importance of spray drying technology in drug delivery, basically for solubility and bioavailability enhancement. Role of additives, selection of polymer, effect of process and formulation parameters, scale up optimization, and IVIVC have been covered to gain the interest of readers about the technology. Design of experiment (DoE) to optimize the spray drying process has been covered in the review. A lot more research work is required to evaluate spray drying as a technology for screening the right polymer for solid dispersion, especially to overcome the issue related to drug re-crystallization and to achieve a stable product both in vitro and in vivo. Based on the recent FDA recommendation, the need of the hour is also to adopt Quality by Design approach in the manufacturing process to carefully optimize the spray drying technology for its smooth transfer from lab scale to commercial scale. PMID:27134535

Role of metal ion solubility in leaching of nuclear waste glasses

International Nuclear Information System (INIS)

Grambow, B.

1982-04-01

From the results of a variety of experiments it can be concluded that reaction of the matrix is the fundamental process that occurs in the leaching of PNL 76-68 glass. This reaction has two aspects. Without solubility restrictions, congruent leaching behavior occurs at all pH values and leachant compositions. When this reaction raises solution concentrations of certain elements to the level at which new solid phases form, these phases will regulate the solution concentration. These solid phases are dominant constituents of the leached layer. For the leaching of PNL 76-68 glass, the solubilities of these reaction products regulate the solution concentration as if the solution is in equilibrium with pure Fe(OH) 3 (amorphous), Zn(OH) 2 (amorphous), Nd(OH) 3 , SrCO 3 or CaCO 3 . The experimental conditions, in particular the pH value, that govern the formation of solid reaction products and control of the solution concentrations can be identified

Simplified sample treatment for the determination of total concentrations and chemical fractionation forms of Ca, Fe, Mg and Mn in soluble coffees.

Science.gov (United States)

Pohl, Pawel; Stelmach, Ewelina; Szymczycha-Madeja, Anna

2014-11-15

A simpler, and faster than wet digestion, sample treatment was proposed prior to determination of total concentrations for selected macro- (Ca, Mg) and microelements (Fe, Mn) in soluble coffees by flame atomic absorption spectrometry. Samples were dissolved in water and acidified with HNO3. Precision was in the range 1-4% and accuracy was better than 2.5%. The method was used in analysis of 18 soluble coffees available on the Polish market. Chemical fractionation patterns for Ca, Fe, Mg and Mn in soluble coffees, as consumed, using a two-column solid-phase extraction method, determined Ca, Mg and Mn were present predominantly as cations (80-93% of total content). This suggests these elements are likely to be highly bioaccessible. Copyright © 2014 Elsevier Ltd. All rights reserved.

Soluble CD30 serum level--an adequate marker for allograft rejection of solid organs?

Science.gov (United States)

Schlaf, G; Altermann, W W; Rothhoff, A; Seliger, B

2007-11-01

The CD30 molecule, a 120 kDa cell surface glycoprotein, is a member of the tumor necrosis factor receptor (TNF-R) superfamily and was originally identified on the surface of Reed-Sternberg cells and anaplastic large cell lymphomas in Hodgkin's disease patients. In addition to lymphoproliferative disorders the expression of CD30 was found in both activated CD8+ and CD4+ Th2 cells which lead to the activation of B-cells and consequently to the inhibition of the Th1-type cellular immunity. The membrane-bound CD30 molecule can be proteolytically cleaved, thereby generating a soluble form (sCD30) of about 85 kDa. Low serum levels of soluble CD30 were found in healthy humans, whereas increased sCD30 serum concentrations were detected under pathophysiological situations such as systemic lupus erythematosus, rheumatoid arthritis, certain viral infections and adult T cell leukaemia/lymphoma. In addition, it has recently been suggested that pre- or post-transplant levels of sCD30 represent a biomarker for graft rejection associated with an impaired outcome for transplanted patients. We here review (i) the current knowledge of the clinical significance of sCD30 serum levels for solid organ transplantations and (ii) our own novel data regarding inter- and intra-individual variations as well as time-dependent alterations of sCD30 levels in patients. (iii) Based on this information the implementation of sCD30 as predictive pre-transplant or post-transplant parameter for solid organ transplantation is critically discussed.

Study of solubility of some metal cyclohexane carbonates

International Nuclear Information System (INIS)

Niyazov, A.N.; Amanov, K.B.; Trapeznikova, V.F.; Kul'maksimov, A.; Kolosova, N.

1978-01-01

The solubility of calcium, magnesium, strontium, barium, cabalt, copper and aluminium cyclohexane, carbonates (CHC) in water has been studied at 25 deg C. The salt solubility has been calculated according to the metal ion concentration in saturated solutions. It has been established, that the cobalt and rare earth cyclohexane carbonates are relatively very soluble in water and have solubility products of SP > 1x10 -5 . The solubility of CHC of multivalent metals increases with the decrease of pH values. Each salt has some ''limiting'' pH value of a solution, below which it decomposes completely and can not exist in a solution in the form of solid phase

Solubility and dissolution enhancement of flurbiprofen by solid dispersion using hydrophilic carriers

Directory of Open Access Journals (Sweden)

Bhaskar Daravath

2018-05-01

Full Text Available ABSTRACT The intent of the current work is to study the effect of polyethylene glycol 8000 and polyethylene glycol 10000 as hydrophilic carriers on dissolution behaviour of flurbiprofen. In the present study, solvent evaporation method was used to prepare flurbiprofen solid dispersions and evaluated for physico-chemical properties, drug-carrier compatibility studies and dissolution behaviour of drug. Solubility studies showed more solubility in higher pH values and formulations SD4 and SD8 were selected to prepare the fast dissolving tablets. FTIR and DSC study showed no interaction and drug was dispersed molecularly in hydrophilic carrier. XRD studies revealed that there was change in the crystallinity of the drug. The results of In vitro studies showed SD8 formulation confer significant improvement (p<0.05 in drug release, Q20 was 99.08±1.35% compared to conventional and marketed tablets (47.31±0.74% and 56.86±1.91%. The mean dissolution time (MDT was reduced to 8.79 min compared to conventional and marketed tablets (25.76 and 22.22 min. indicating faster drug release. The DE (% dissolution efficiency was increased by 2.5 folds (61.63% compared to conventional tablets (23.71%. From the results, it is evident that polyethylene glycol solid dispersions in less carrier ratio may enhance the solubility and there by improve the dissolution rate of flurbiprofen.

Studies on dissolution enhancement and mathematical modeling of drug release of a poorly water-soluble drug using water-soluble carriers.

Science.gov (United States)

Ahuja, Naveen; Katare, Om Prakash; Singh, Bhupinder

2007-01-01

Role of various water-soluble carriers was studied for dissolution enhancement of a poorly soluble model drug, rofecoxib, using solid dispersion approach. Diverse carriers viz. polyethylene glycols (PEG 4000 and 6000), polyglycolized fatty acid ester (Gelucire 44/14), polyvinylpyrollidone K25 (PVP), poloxamers (Lutrol F127 and F68), polyols (mannitol, sorbitol), organic acid (citric acid) and hydrotropes (urea, nicotinamide) were investigated for the purpose. Phase-solubility studies revealed AL type of curves for each carrier, indicating linear increase in drug solubility with carrier concentration. The sign and magnitude of the thermodynamic parameter, Gibbs free energy of transfer, indicated spontaneity of solubilization process. All the solid dispersions showed dissolution improvement vis-à-vis pure drug to varying degrees, with citric acid, PVP and poloxamers as the most promising carriers. Mathematical modeling of in vitro dissolution data indicated the best fitting with Korsemeyer-Peppas model and the drug release kinetics primarily as Fickian diffusion. Solid state characterization of the drug-poloxamer binary system using XRD, FTIR, DSC and SEM techniques revealed distinct loss of drug crystallinity in the formulation, ostensibly accounting for enhancement in dissolution rate.

(Solid + liquid) phase diagram for (indomethacin + nicotinamide)-methanol or methanol/ethyl acetate mixture and solubility behavior of 1:1 (indomethacin + nicotinamide) co-crystal at T = (298.15 and 313.15) K

International Nuclear Information System (INIS)

Sun, Xiaowei; Yin, Qiuxiang; Ding, Suping; Shen, Zhiming; Bao, Ying; Gong, Junbo; Hou, Baohong; Hao, Hongxun; Wang, Yongli; Wang, Jingkang; Xie, Chuang

2015-01-01

Highlights: • Ternary phase diagrams of (IMC + NCT)-methanol or methanol/ethyl acetate mixture at T = (298.15 and 313.15) K were measured. • The effects of temperature and introduced ethyl acetate on solid phase stability were discussed. • Solubility of (IMC + NCT) cocrystals was first correlated using a model considering solubility product and complexation. • Solubility of (IMC + NCT) cocrystals as a function of co-former concentration was evaluated. - Abstract: (Solid + liquid) equilibrium data for indomethacin (IMC) and nicotinamide (NCT) in both methanol (MeOH) and methanol/ethyl acetate (EA) mixture were determined using a static method at T = (298.15 and 313.15) K under atmospheric pressure. The 1:1 (IMC + NCT) co-crystal and IMC·MeOH were found in both systems under conditions investigated. The solubility of the 1:1 (IMC + NCT) co-crystal was correlated using a mathematical model consisting of both solubility product and a complexation process. Solubility of (IMC + NCT) co-crystals as a function of co-former (NCT) concentration was evaluated. It was found that temperature has a significant effect on the formation of methanol solvate in the systems investigated. Solvate formation could be suppressed either by increasing temperature or using solvent mixtures. Additionally, the solvent mixture could level out the solubility differences between IMC and NCT, resulting in larger and more symmetric regions for the (IMC + NCT) co-crystal, which would be helpful to the development of the co-crystallization process for the 1:1 (IMC + NCT) co-crystal

Solubility of jarosite solid solutions precipitated from acid mine waters, Iron Mountain, California

Science.gov (United States)

Alpers, Charles N.; Nordstrom, D. Kirk; Ball, J.W.

1989-01-01

Because of the common occurrence of 15 to 25 mole percent hydronium substitution on the alkali site in jarosites, it is necessary to consider the hydronium content of jarosites in any attempt at rigorous evaluation of jarosite solubility or of the saturation state of natural waters with respect to jarosite. A Gibbs free energy of 3293.5±2.1 kJ mol-1 is recommended for a jarosite solid solution of composition K.77Na.03(H3O).20Fe3(SO4)2(OH)6. Solubility determinations for a wider range of natural and synthetic jarosite solid solutions will be necessary to quantify the binary and ternary mixing parameters in the (K-Na-H3O) system. In the absence of such studies, molar volume data for endmember minerals indicate that the K-H3O substitution in jarosite is probably closer to ideal mixing than either the Na-K or Na-H3O substitution.

Terminal solid solubility of hydrogen in titanium

International Nuclear Information System (INIS)

Giroldi, J.P.; Vizcaino, Pablo; Banchik, Abraham David

2003-01-01

A Research and Development program to build a data base is currently under progress to support the local titanium fabrication. In the present work the temperature of the Terminal Solid Solubility on dissolution (TSSd) and precipitation (TSSp) of titanium hydrides in the Ti α-phase were both measured in the same thermal cycle with a Differential Scanning Calorimeter (DSC). The local titanium producer (FAESA) provided ASTM grade 1 pure Ti bars of about 2,5 cm in diameter. Samples weighting between 50 to 200 mg were cut with a diamond disc and the parallelepiped faces were all carefully ground with SiC papers, then picked in a HNO 3 plus HF aqueous solution and finally dried out with ethanol and hot air. Pairs of (TSSd, TSSp) values for α + δ → α and α → α + δ transformation temperatures in titanium were determined with the same calorimetric procedure already used to calculate the TSS values in zirconium. Data were taken from the same sample during the heating up and cooling down cycle of the second calorimeter run made with the same rate of 20 C degrees / minute. The Cathodic Charging technique was used to charge the samples at different hydrogen concentrations between the 'as fabricated' value and the concentration corresponding to the eutectoid temperature. A mixture of glycerin and phosphoric acid in a 2:1 ratio and a current density of 0,05 to 0,1 Amp/cm 2 were applied to different samples during 24 to 96 hours to get a wide range of hydrogen concentrations. A homogenization heat treatment at 400 C degrees for 45 minutes -made at open air in an electric furnace- was applied to each sample to dissolve the massive hydrides at the sample surfaces and diffuse them into the bulk of the sample. The hydrogen concentration of each sample was measured after the final calorimetric run using the Extraction Method in Liquid State under an inert atmosphere using a Leco RH-404 model Hydrogen Determinator. The experimental data follows a linear relationship -with a

A novel osmotic pump-based controlled delivery system consisting of pH-modulated solid dispersion for poorly soluble drug flurbiprofen: in vitro and in vivo evaluation.

Science.gov (United States)

Li, Shujuan; Wang, Xiaoyu; Wang, Yingying; Zhao, Qianqian; Zhang, Lina; Yang, Xinggang; Liu, Dandan; Pan, Weisan

2015-01-01

In this study, a novel controlled release osmotic pump capsule consisting of pH-modulated solid dispersion for poorly soluble drug flurbiprofen (FP) was developed to improve the solubility and oral bioavailability of FP and to minimize the fluctuation of plasma concentration. The pH-modulated solid dispersion containing FP, Kollidon® 12 PF and Na2CO3 at a weight ratio of 1/4.5/0.02 was prepared using the solvent evaporation method. The osmotic pump capsule was assembled by semi-permeable capsule shell of cellulose acetate (CA) prepared by the perfusion method. Then, the solid dispersion, penetration enhancer, and suspending agents were tableted and filled into the capsule. Central composite design-response surface methodology was used to evaluate the influence of factors on the responses. A second-order polynomial model and a multiple linear model were fitted to correlation coefficient of drug release profile and ultimate cumulative release in 12 h, respectively. The actual response values were in good accordance with the predicted ones. The optimized formulation showed a complete drug delivery and zero-order release rate. Beagle dogs were used to be conducted in the pharmacokinetic study. The in vivo study indicated that the relative bioavailability of the novel osmotic pump system was 133.99% compared with the commercial preparation. The novel controlled delivery system with combination of pH-modulated solid dispersion and osmotic pump system is not only a promising strategy to improve the solubility and oral bioavailability of poorly soluble ionizable drugs but also an effective way to reduce dosing frequency and minimize the plasma fluctuation.

Probing the mechanisms of drug release from amorphous solid dispersions in medium-soluble and medium-insoluble carriers.

Science.gov (United States)

Sun, Dajun D; Lee, Ping I

2015-08-10

The objective of the current study is to mechanistically differentiate the dissolution and supersaturation behaviors of amorphous drugs from amorphous solid dispersions (ASDs) based on medium-soluble versus medium-insoluble carriers under nonsink dissolution conditions through a direct head-to-head comparison. ASDs of indomethacin (IND) were prepared in several polymers which exhibit different solubility behaviors in acidic (pH1.2) and basic (pH7.4) dissolution media. The selected polymers range from water-soluble (e.g., PVP and Soluplus) and water-insoluble (e.g., ethylcellulose and Eudragit RL PO) to those only soluble in an acidic or basic dissolution medium (e.g., Eudragit E100, Eudragit L100, and HPMCAS). At 20wt.% drug loading, DSC and powder XRD analysis confirmed that the majority of incorporated IND was present in an amorphous state. Our nonsink dissolution results confirm that whether the carrier matrix is medium soluble determines the release mechanism of amorphous drugs from ASD systems which has a direct impact on the rate of supersaturation generation, thus in turn affecting the evolution of supersaturation in amorphous systems. For example, under nonsink dissolution conditions, the release of amorphous IND from medium-soluble carriers is governed by a dissolution-controlled mechanism leading to an initial surge of supersaturation followed by a sharp decline in drug concentration due to rapid nucleation and crystallization. In contrast, the dissolution of IND ASD from medium-insoluble carriers is more gradual as drug release is regulated by a diffusion-controlled mechanism by which drug supersaturation is built up gradually and sustained over an extended period of time without any apparent decline. Since several tested carrier polymers can be switched from soluble to insoluble by simply changing the pH of the dissolution medium, the results obtained here provide unequivocal evidence of the proposed transition of kinetic solubility profiles from the

Preparation and evaluation of azithromycin binary solid dispersions using various polyethylene glycols for the improvement of the drug solubility and dissolution rate

Directory of Open Access Journals (Sweden)

Ehsan Adeli

Full Text Available ABSTRACT Azithromycin is a water-insoluble drug, with a very low bioavailability. In order to increase the solubility and dissolution rate, and consequently increase the bioavailability of poorly-soluble drugs (such as azithromycin, various techniques can be applied. One of such techniques is "solid dispersion". This technique is frequently used to improve the dissolution rate of poorly water-soluble compounds. Owing to its low solubility and dissolution rate, azithromycin does not have a suitable bioavailability. Therefore, the main purpose of this investigation was to increase the solubility and dissolution rate of azithromycin by preparing its solid dispersion, using different Polyethylene glycols (PEG. Preparations of solid dispersions and physical mixtures of azithromycin were made using PEG 4000, 6000, 8000, 12000 and 20000 in various ratios, based on the solvent evaporation method. From the studied drug release profile, it was discovered that the dissolution rate of the physical mixture, as the well as the solid dispersions, were higher than those of the drug alone. There was no chemical incompatibility between the drug and polymer from the observed Infrared (IR spectra. Drug-polymer interactions were also investigated using Differential Scanning Calorimetry (DSC, Powder X-Ray Diffraction (PXRD and Scanning Election Microscopy (SEM. In conclusion, the dissolution rate and solubility of azithromycin were found to improve significantly, using hydrophilic carriers, especially PEG 6000.

Freeze concentration of lime juice

Directory of Open Access Journals (Sweden)

Ampawan Tansakul

2008-11-01

Full Text Available The main objective of this research was to study the effects of processing conditions, i.e. cooling medium temperature (-6, -12 and -18C and scraper blade rotational speed (50, 100 and 150 rpm on the freeze concentration of lime juice. The initial soluble solid content of lime juice was 7.6 Brix. Results showed that soluble solid content of lime juice increased as cooling medium temperature decreased while scraper blade rotational speed increased. It was also found that the processing condition with -18˚C cooling medium temperature and 150 rpm rotational speed of the scraper blade was the best among all studied conditions, although the loss of the soluble solids with ice crystals during ice separation was relatively high at 35%.

Evaluation of soluble solids content and pH of ice cream treated with gamma radiation

Energy Technology Data Exchange (ETDEWEB)

Rogovschi, V.D.; Nunes, T.C.F.; Fabbri, A.D.T.; Sagretti, J.M.; Sabato, S.F. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2011-07-01

The ice cream is considered an aerated suspension of fat and ice crystals in a concentrated sugar solution containing hydrocolloids, proteins and casein micelles. Only in Brazil, in the year 2010, it was produced 1120 million liter of ice cream and due to high demand by the consumers, this is considered the most important product of the dairy industry. The objective of this work is to evaluate the soluble solids content (SSC) and the hydrogenionic potential (pH) of vanilla ice cream conditioned in isothermal boxes irradiated with 3.0 and 5.0 kGy in the Multipurpose Irradiator of {sup 60}Co located at IPEN - CNEN/SP. It can be concluded that the treatment of ice cream with gamma radiation did not cause changes in the analyzed parameters. . (author)

Evaluation of soluble solids content and pH of ice cream treated with gamma radiation

International Nuclear Information System (INIS)

Rogovschi, V.D.; Nunes, T.C.F.; Fabbri, A.D.T.; Sagretti, J.M.; Sabato, S.F.

2011-01-01

The ice cream is considered an aerated suspension of fat and ice crystals in a concentrated sugar solution containing hydrocolloids, proteins and casein micelles. Only in Brazil, in the year 2010, it was produced 1120 million liter of ice cream and due to high demand by the consumers, this is considered the most important product of the dairy industry. The objective of this work is to evaluate the soluble solids content (SSC) and the hydrogenionic potential (pH) of vanilla ice cream conditioned in isothermal boxes irradiated with 3.0 and 5.0 kGy in the Multipurpose Irradiator of 60 Co located at IPEN - CNEN/SP. It can be concluded that the treatment of ice cream with gamma radiation did not cause changes in the analyzed parameters. . (author)

Enhancement of solubility and bioavailability of ambrisentan by solid dispersion using Daucus carota as a drug carrier: formulation, characterization, in vitro, and in vivo study.

Science.gov (United States)

Deshmane, Subhash; Deshmane, Snehal; Shelke, Santosh; Biyani, Kailash

2018-06-01

Ambrisentan is an US FDA approved drug, it is the second oral endothelin A receptor antagonist known for the treatment of pulmonary arterial hypertension, but its oral administration is limited due to its poor water solubility. Hence, the objective of the investigation was focused on enhancement of solubility and bioavailability of ambrisentan by solid dispersion technique using natural Daucus carota extract as drug carrier. Drug carrier was evaluated for solubility, swelling index, viscosity, angle of repose, hydration capacity, and acute toxicity test (LD 50 ). Ambrisentan was studied for the saturation solubility, phase solubility, and Gibbs free energy change. Compatibility of drug and the natural carrier was confirmed by DSC, FTIR, and XRD. Solid dispersions were evaluated for drug content, solubility, morphology, in vitro, and in vivo study. Screening of the natural carrier showed the desirable properties like water solubility, less swelling index, less viscosity, and acute toxicity study revealed no any clinical symptoms of toxicity. Drug and carrier interaction study confirmed the compatibility to consider its use in the formulation. Formed particles were found to be spherical with smooth surface. In vitro studies revealed higher drug release from the solid dispersion than that of the physical mixture. Bioavailability study confirms the increased absorption and bioavailability by oral administration of solid dispersion. Hence, it can be concluded that the natural Daucus carota extract can be the better alternative source for the preparation of solid dispersion and/or other dosage forms for improving solubility and bioavailability.

Natural polymers: Best carriers for improving bioavailability of poorly water soluble drugs in solid dispersions

OpenAIRE

Sandip Sapkal; Mahesh Narkhede; Mukesh Babhulkar; Gautam Mehetre; Ashish Rathi

2013-01-01

ABSTRACTNatural polymers and its modified forms can be used as best alternative for improving bioavailabilityof poorly water soluble drugs in solid dispersion. Most of the natural polymersare hydrophilic and having high swelling capacity. Recent trend towards the use of naturalpolymer demands the replacement of synthetic additives with natural ones. Many plant derivednatural polymers are studied for use in solid dispersion systems, out of which naturalgums, cyclodextrin and carbohydrate are m...

Effect of initial total solids concentration on volatile fatty acid production from food waste during anaerobic acidification.

Science.gov (United States)

Wang, Quan; Jiang, Jianguo; Zhang, Yujing; Li, Kaimin

2015-01-01

The effect of initial total solids (TS) concentration on volatile fatty acid (VFAs) production from food waste under mesophilic conditions (35 °C) was determined. VFAs concentration and composition, biogas production, soluble chemical oxygen demand concentration, TS and volatile solids (VS) reduction, and ammonia nitrogen [Formula: see text] release were investigated. The VFAs concentrations were 26.10, 39.68, 59.58, and 62.64 g COD/L at TS contents of 40, 70, 100, and 130 g/L, respectively. While the VFAs' yields ranged from 0.467 to 0.799 g COD/g VSfed, decreased as initial TS increased. The percentage of propionate was not affected by TS concentration, accounting for 30.19-34.86% of the total VFAs, while a higher percentage of butyrate and lower percentage of acetate was achieved at a higher TS concentration. Biogas included mainly hydrogen and carbon dioxide and the maximum hydrogen yield of 148.9 ml/g VSfed was obtained at 130 g TS/L. [Formula: see text] concentration, TS and VS reductions increased as initial TS increased. Considering the above variables, we conclude that initial TS of 100 g/L shall be the most appropriate to VFAs production.

Waste activated sludge fermentation: effect of solids retention time and biomass concentration.

Science.gov (United States)

Yuan, Q; Sparling, R; Oleszkiewicz, J A

2009-12-01

Laboratory scale, room temperature, semi-continuous reactors were set-up to investigate the effect of solids retention time (SRT, equal to HRT hydraulic retention time) and biomass concentration on generation of volatile fatty acids (VFA) from the non-methanogenic fermentation of waste activated sludge (WAS) originating from an enhanced biological phosphorus removal process. It was found that VFA yields increased with SRT. At the longest SRT (10d), improved biomass degradation resulted in the highest soluble to total COD ratio and the highest VFA yield from the influent COD (0.14g VFA-COD/g TCOD). It was also observed that under the same SRT, VFA yields increased when the biomass concentration decreased. At a 10d SRT the VFA yield increased by 46%, when the biomass concentration decreased from 13g/L to 4.8g/L. Relatively high nutrient release was observed during fermentation. The average phosphorus release was 17.3mg PO(4)-P/g TCOD and nitrogen release was 25.8mg NH(4)-N/g TCOD.

Semen quality and concentration of soluble proteins in the seminal plasma of Alpine bucks Semen quality and concentration of soluble proteins in the seminal plasma of Alpine bucks

Directory of Open Access Journals (Sweden)

Simone Eliza Facione Guimarães

2010-06-01

Full Text Available It was aimed to study the in vitro seminal quality analyzed by complementary tests and to compare them with physical, morphological and biochemical aspects of male goat semen of the Alpine breed. This experiment took place at the Federal University of Viçosa, situated at 20º45’ S latitude and 42º51’ W longitude, Southwest of Brazil. It was done during the summer months of January and February, and three adult male goats of the Alpine breed were used in intensive conditions. The semen was collected by artificial vagina method. In all semen samples (45 ejaculates, after the physical and morphological analysis, the hiposmotic test was done. In 24 ejaculates, it were done thermo-resistance test, and in 21 ejaculates it were determined the concentration of total soluble proteins in seminal plasma. The male goats presented difference in the semen physical and morphological aspects, in the hiposmotic test and thermo-resistance test, but they did not presented difference in total soluble proteins concentration in seminal plasma. Results of the slow thermo-resistance test and hiposmotic test were positively correlated (r = 0.60. It was concluded, according to our results, that the concentration of total soluble proteins in seminal plasma can not be used as a parameter to predict the seminal quality of Alpine bucks.It was aimed to study the in vitro seminal quality analyzed by complementary tests and to compare them with physical, morphological and biochemical aspects of male goat semen of the Alpine breed. This experiment took place at the Federal University of Viçosa, situated at 20º45’ S latitude and 42º51’ W longitude, Southwest of Brazil. It was done during the summer months of January and February, and three adult male goats of the Alpine breed were used in intensive conditions. The semen was collected by artificial vagina method. In all semen samples (45 ejaculates, after the physical and morphological analysis, the hiposmotic test

Le Chatelier's Principle: The Effect of Temperature on the Solubility of Solids in Liquids.

Science.gov (United States)

Brice, L. K.

1983-01-01

Provides a rigorous but straightforward thermodynamic treatment of the temperature dependence of the solubility of solids in liquids that is suitable for presentation to undergraduates, suggesting how to approach the qualitative aspects of the subject for freshmen. Considers unsolvated/solvated solutes and Le Chatelier's principle. (JN)

Sensitivity analysis of uranium solubility under strongly oxidizing conditions

International Nuclear Information System (INIS)

Liu, L.; Neretnieks, I.

1999-01-01

To evaluate the effect of geochemical conditions in the repository on the solubility of uranium under strongly oxidizing conditions, a mathematical model has been developed to determine the solubility, by utilizing a set of nonlinear algebraic equations to describe the chemical equilibria in the groundwater environment. The model takes into account the predominant precipitation-dissolution reactions, hydrolysis reactions and complexation reactions that may occur under strongly oxidizing conditions. The model also includes the solubility-limiting solids induced by the presence of carbonate, phosphate, silicate, calcium, and sodium in the groundwater. The thermodynamic equilibrium constants used in the solubility calculations are essentially taken from the NEA Thermochemical Data Base of Uranium, with some modification and some uranium minerals added, such as soddyite, rutherfordite, uranophane, uranyl orthophosphate, and becquerelite. By applying this model, the sensitivities of uranium solubility to variations in the concentrations of various groundwater component species are systematically investigated. The results show that the total analytical concentrations of carbonate, phosphate, silicate, and calcium in deep groundwater play the most important role in determining the solubility of uranium under strongly oxidizing conditions

The solubilities of significant organic compounds in HLW tank supernate solutions -- FY 1995 progress report

International Nuclear Information System (INIS)

Barney, G.S.

1996-01-01

At the Hanford Site organic compounds were measured in tank supernate simulant solutions during FY 1995. This solubility information will be used to determine if these organic salts could exist in solid phases (saltcake or sludges) in the waste where they might react violently with the nitrate or nitrite salts present in the tanks. Solubilities of sodium glycolate, succinate, and caproate salts; iron and aluminum and butylphosphate salts; and aluminum oxalate were measured in simulated waste supernate solutions at 25 degree C, 30 degree C, 40 degree C, and 50 degree C. The organic compounds were selected because they are expected to exist in relatively high concentrations in the tanks. The solubilities of sodium glycolate, succinate, caproate, and butylphosphate in HLW tank supernate solutions were high over the temperature and sodium hydroxide concentration ranges expected in the tanks. High solubilities will prevent solid sodium salts of these organic acids from precipitating from tank supernate solutions. The total organic carbon concentrations (YOC) of actual tank supernates are generally much lower than the TOC ranges for simulated supernate solutions saturated (at the solubility limit) with the organic salts. This is so even if all the dissolved carbon in a given tank and supernate is due to only one of these eight soluble compounds (an unlikely situation). Metal ion complexes of and butylphosphate and oxalate in supernate solutions were not stable in the presence of the hydroxide concentrations expected in most tanks. Iron and aluminum dibutylphosphate compounds reacted with hydroxide to form soluble sodium dibutylphosphate and precipitated iron and aluminum hydroxides. Aluminum oxalate complexes were also not stable in the basic simulated supernate solutions. Solubilities of all the organic salts decrease with increasing sodium hydroxide concentration because of the common ion effect of Na+. Increasing temperatures raised the solubilities of the organic

Determination of radionuclide solubility limits to be used in SR 97. Uncertainties associated to calculated solubilities

Energy Technology Data Exchange (ETDEWEB)

Bruno, J.; Cera, E.; Duro, L.; Jordana, S. [QuantiSci S.L., Barcelona (Spain); Pablo, J. de [DEQ-UPC, Barcelona (Spain); Savage, D. [QuantiSci Ltd., Henley-on-Thames (United Kingdom)

1997-12-01

The thermochemical behaviour of 24 critical radionuclides for the forthcoming SR97 PA exercise is discussed. The available databases are reviewed and updated with new data and an extended database for aqueous and solid species of the radionuclides of interest is proposed. We have calculated solubility limits for the radionuclides of interest under different groundwater compositions. A sensitivity analysis of the calculated solubilities with the composition of the groundwater is presented. Besides selecting the most likely solubility limiting phases, in this work we have used coprecipitation approaches in order to calculate more realistic solubility limits for minor radionuclides, such as Ra, Am and Cm. The comparison between the calculated solubilities and the concentrations measured in relevant natural systems (NA) and in spent fuel leaching experiments helps to assess the validity of the methodology used and to derive source term concentrations for the radionuclides studied. The uncertainties associated to the solubilities of the main radionuclides involved in the spent nuclear fuel have also been discussed in this work. The variability of the groundwater chemistry; redox conditions and temperature of the system have been considered the main factors affecting the solubilities. In this case, a sensitivity analysis has been performed in order to study solubility changes as a function of these parameters. The uncertainties have been calculated by including the values found in a major extent in typical granitic groundwaters. The results obtained from this analysis indicate that there are some radionuclides which are not affected by these parameters, i.e. Ag, Cm, Ho, Nb, Ni, Np, Pu, Se, Sm, Sn, Sr, Tc and U

Water-soluble metal-binding polymers with ultrafiltration: A technology for the removal, concentration, and recovery of metal ions from aqueous streams

International Nuclear Information System (INIS)

Smith, B.F.; Robison, T.W.; Jarvinen, G.D.

1997-01-01

The use of water-soluble metal-binding polymers coupled with ultrafiltration (UF) is a technology under development to selectively concentrate and recover valuable or regulated metal-ions from dilute process or waste waters. The polymers have a sufficiently large molecular size that they can be separated and concentrated using commercially available UF technology. The polymers can then be reused by changing the solution conditions to release the metal-ions, which are recovered in a concentrated form for recycle or disposal. Pilot-scale demonstrations have been completed for a variety of waste streams containing low concentrations of metal ions including electroplating wastes (zinc and nickel) and nuclear waste streams (plutonium and americium). Many other potential commercial applications exist including remediation of contaminated solids. An overview of both the pilot-scale demonstrated applications and small scale testing of this technology are presented

Water-soluble metal-binding polymers with ultrafiltration: A technology for the removal, concentration, and recovery of metal ions from aqueous streams

Energy Technology Data Exchange (ETDEWEB)

Smith, B.F.; Robison, T.W.; Jarvinen, G.D.

1997-12-31

The use of water-soluble metal-binding polymers coupled with ultrafiltration (UF) is a technology under development to selectively concentrate and recover valuable or regulated metal-ions from dilute process or waste waters. The polymers have a sufficiently large molecular size that they can be separated and concentrated using commercially available UF technology. The polymers can then be reused by changing the solution conditions to release the metal-ions, which are recovered in a concentrated form for recycle or disposal. Pilot-scale demonstrations have been completed for a variety of waste streams containing low concentrations of metal ions including electroplating wastes (zinc and nickel) and nuclear waste streams (plutonium and americium). Many other potential commercial applications exist including remediation of contaminated solids. An overview of both the pilot-scale demonstrated applications and small scale testing of this technology are presented.

pH-metric solubility. 3. Dissolution titration template method for solubility determination.

Science.gov (United States)

Avdeef, A; Berger, C M

2001-12-01

The main objective of this study was to develop an effective potentiometric saturation titration protocol for determining the aqueous intrinsic solubility and the solubility-pH profile of ionizable molecules, with the specific aim of overcoming incomplete dissolution conditions, while attempting to shorten the data collection time. A modern theory of dissolution kinetics (an extension of the Noyes-Whitney approach) was applied to acid-base titration experiments. A thermodynamic method was developed, based on a three-component model, to calculate interfacial, diffusion-layer, and bulk-water reactant concentrations in saturated solutions of ionizable compounds perturbed by additions of acid/base titrant, leading to partial dissolution of the solid material. Ten commercial drugs (cimetidine, diltiazem hydrochloride, enalapril maleate, metoprolol tartrate, nadolol, propoxyphene hydrochloride, quinine hydrochloride, terfenadine, trovafloxacin mesylate, and benzoic acid) were chosen to illustrate the new titration methodology. It was shown that the new method is about 10 times faster in determining equilibrium solubility constants, compared to the traditional saturation shake-flask methods.

Fast Measurement of Soluble Solid Content in Mango Based on Visible and Infrared Spectroscopy Technique

Science.gov (United States)

Yu, Jiajia; He, Yong

Mango is a kind of popular tropical fruit, and the soluble solid content is an important in this study visible and short-wave near-infrared spectroscopy (VIS/SWNIR) technique was applied. For sake of investigating the feasibility of using VIS/SWNIR spectroscopy to measure the soluble solid content in mango, and validating the performance of selected sensitive bands, for the calibration set was formed by 135 mango samples, while the remaining 45 mango samples for the prediction set. The combination of partial least squares and backpropagation artificial neural networks (PLS-BP) was used to calculate the prediction model based on raw spectrum data. Based on PLS-BP, the determination coefficient for prediction (Rp) was 0.757 and root mean square and the process is simple and easy to operate. Compared with the Partial least squares (PLS) result, the performance of PLS-BP is better.

Investigations on uranyl nitrate solubility in nitric acid in different concentrations at temperatures of 50C

International Nuclear Information System (INIS)

Deigele, E.

1983-01-01

The solubility of uranyl nitrate was studied in nitric acid solutions of different concentrations at a temperature of 5 0 C. This temperature was chosen with a view to using water as coolant and to facilitate the handling of the strong acid solutions. Accurate curves were established by a multitude of accurate measurements in the high concentration range. Further solubility curves can be derived from this basic curve. Some of the precipitates in the interesting regions of the solubility curve were analyzed. (orig./EF) [de

Detection of colloidal silver chloride near solubility limit

Science.gov (United States)

Putri, K. Y.; Adawiah, R.

2018-03-01

Detection of nanoparticles in solution has been made possible by several means; one of them is laser-induced breakdown detection (LIBD). LIBD is able to distinguish colloids of various sizes and concentrations. This technique has been used in several solubility studies. In this study, the formation of colloids in a mixed system of silver nitrate and sodium chloride was observed by acoustic LIBD. Silver chloride has low solubility limit, therefore LIBD measurement is appropriate. Silver and chloride solutions with equal concentrations, set at below and above the solubility of silver chloride as the expected solid product, were mixed and the resulting colloids were observed. The result of LIBD measurement showed that larger particles were present as more silver and chloride introduced. However, once the concentrations exceeded the solubility limit of silver chloride, the detected particle size seemed to be decreasing, hence suggested the occurrence of coprecipitation process. This phenomenon indicated that the ability of LIBD to detect even small changes in colloid amounts might be a useful tool in study on formation and stability of colloids, i.e. to confirm whether nanoparticles synthesis has been successfully performed and whether the system is stable or not.

Influence of temperature, concentration and shear rate on the rheological behavior of malay apple (Syzygium malaccense juice

Directory of Open Access Journals (Sweden)

Pedro Henrique Santos

Full Text Available Summary The aim of this study was to evaluate the rheological behavior of malay apple, a traditional Amazonian fruit with high bioactive properties, at different temperatures and soluble solids concentrations. The experiments were carried out in a Brookfield R/S Plus rheometer with concentric cylinders geometry. Power Law, Herschel-Bulkley, Mizrahi-Berk, and Sisko rheological models were fitted to the experimental data. The malay apple juice (pulp and skin showed a pseudoplastic behavior for all temperatures and concentrations with flow behavior indexes lower than 1. The temperature effect on the samples’ apparent viscosity was analyzed by the Arrhenius equation. The activation energy increased with a decrease in the soluble solids concentration, showing that the lower the concentration, the greater the temperature influence on the apparent viscosity. The soluble solids effect was described by the exponential equation. The exponential factor increased with the temperature increasing, showing that the higher the temperature, the greater the effect of the soluble solids concentration on samples’ apparent viscosity. Finally, a triparametric mathematical model combining temperature, concentration, and shear rate was proposed aiming to evaluate its effects on the samples’ apparent viscosity and has accurately adjusted to the data with high correlation index R2.

Pressurized capillary electrochromatographic analysis of water-soluble vitamins by combining with on-line concentration technique.

Science.gov (United States)

Jia, Li; Liu, Yaling; Du, Yanyan; Xing, Da

2007-06-22

A pressurized capillary electrochromatography (pCEC) system was developed for the separation of water-soluble vitamins, in which UV absorbance was used as the detection method and a monolithic silica-ODS column as the separation column. The parameters (type and content of organic solvent in the mobile phase, type and concentration of electrolyte, pH of the electrolyte buffer, applied voltage and flow rate) affecting the separation resolution were evaluated. The combination of two on-line concentration techniques, namely, solvent gradient zone sharpening effect and field-enhanced sample stacking, was utilized to improve detection sensitivity, which proved to be beneficial to enhance the detection sensitivity by enabling the injection of large volumes of samples. Coupling electrokinetic injection with the on-line concentration techniques was much more beneficial for the concentration of positively charged vitamins. Comparing with the conventional injection mode, the enhancement in the detection sensitivities of water-soluble vitamins using the on-line concentration technique is in the range of 3 to 35-fold. The developed pCEC method was applied to evaluate water-soluble vitamins in corns.

Solid dispersions: a strategy for poorly aqueous soluble drugs and technology updates.

Science.gov (United States)

Alam, Mohd Aftab; Ali, Raisuddin; Al-Jenoobi, Fahad Ibrahim; Al-Mohizea, Abdullah M

2012-11-01

Present article reviews solid dispersion (SD) technologies and other patented inventions in the area of pharmaceutical SDs, which provide stable amorphous SDs. The review briefly compiles different techniques for preparing SDs, their applications, characterization of SDs, types of SDs and also elaborates the carriers used to prepare SDs. The advantages of recently introduced SD technologies such as RightSize(™), closed-cycle spray drying (CSD), Lidose® are summarized. Stability-related issues like phase separation, re-crystallization and methods to curb these problems are also discussed. A patented carrier-screening tool for predicting physical stability of SDs on the basis of drug-carrier interaction is explained. Applications of SD technique in controlled drug delivery systems and cosmetics are explored. Review also summarizes the carriers such as Soluplus®, Neusilin®, Solumer(TM) used to prepare stable amorphous SD. Binary and ternary SDs are found to be more stable and provide better enhancement of solubility or dissolution of poorly water-soluble drugs. The use of surfactants in the carrier system of SD is a recent trend. Surfactants and polymers provide stability against re-crystallization of SDs, surfactants also improve solubility and dissolution of drug.

Concentration of pineapple juice by reverse osmosis: physicochemical characteristics and consumer acceptance

Directory of Open Access Journals (Sweden)

Daniel Simões Couto

2011-12-01

Full Text Available Reverse osmosis has been used for the concentration of fruit juices with promising considering the quality of the obtained products. The objective of this study was to concentrate single strength pineapple juice by reverse osmosis. The concentration was carried out with polyamide composite membranes in a 0.65 m² plate and frame module at 60 bar transmembrane pressure at 20 °C. The permeate flux was 17 L.hm-2. The total soluble solid content of the juice increased from 11 to 31 °Brix corresponding to a Volumetric Concentration Factor (VCF of 2.9. The concentration of soluble solids, total solids, and total acidity increased proportionally to FCV. The concentrated juice and three commercial concentrated pineapple juices were evaluated regarding preference and purchase intention by 79 pineapple juice consumers. The concentrated juice by reverse osmosis was the preferred among consumers. It can be concluded that this process may be considered an alternative to the pre-concentration of fruit juices.

The determination of solubility and diffusion coefficient for solids in liquids by an inverse measurement technique using cylinders of amorphous glucose as a model compound

International Nuclear Information System (INIS)

Hu, Chengyao; Huang, Pei

2011-01-01

The importance of sugar and sugar-containing materials is well recognized nowadays, owing to their application in industrial processes, particularly in the food, pharmaceutical and cosmetic industries. Because of the large numbers of those compounds involved and the relatively small number of solubility and/or diffusion coefficient data for each compound available, it is highly desirable to measure the solubility and/or diffusion coefficient as efficiently as possible and to be able to improve the accuracy of the methods used. In this work, a new technique was developed for the measurement of the diffusion coefficient of a stationary solid solute in a stagnant solvent which simultaneously measures solubility based on an inverse measurement problem algorithm with the real-time dissolved amount profile as a function of time. This study differs from established techniques in both the experimental method and the data analysis. The experimental method was developed in which the dissolved amount of solid solute in quiescent solvent was investigated using a continuous weighing technique. In the data analysis, the hybrid genetic algorithm is used to minimize an objective function containing a calculated and a measured dissolved amount with time. This is measured on a cylindrical sample of amorphous glucose in methanol or ethanol. The calculated dissolved amount, that is a function of the unknown physical properties of the solid solute in the solvent, is calculated by the solution of the two-dimensional nonlinear inverse natural convection problem. The estimated values of the solubility of amorphous glucose in methanol and ethanol at 293 K were respectively 32.1 g/100 g methanol and 1.48 g/100 g ethanol, in agreement with the literature values, and support the validity of the simultaneously measured diffusion coefficient. These results show the efficiency and the stability of the developed technique to simultaneously estimate the solubility and diffusion coefficient. Also

Mechanistic study of solubility enhancement of nifedipine using vitamin E TPGS or solutol HS-15.

Science.gov (United States)

Rajebahadur, Minal; Zia, Hossein; Nues, Anthony; Lee, Chong

2006-01-01

The objective of our study was to find mechanisms responsible for solubility enhancement of nifedipine in solid dispersions of vitamin E TPGS and/or solutol HS-15. Solid dispersions of nifedipine with selected polymers such as vitamin E TPGS, solutol HS-15, PEG(1,000), and lipocol C-10 of varying drug/polymer ratios were prepared by a fusion method. The solubility enhancement was found to be in the order of vitamin E TPGS > solutol HS-15 > lipocol C-10 > PEG(1,000). Lipocol C-10, with a similar hydrophilic-lipophilic value as vitamin E TPGS, showed a comparable retained solubility enhancement during saturation solubility studies but had lower dissolution profile. Overall, vitamin E TPGS showed the best solubility and dissolution performance, while solutol HS-15 and lipocol C-10 demonstrated moderate solubility enhancements. Solid dispersions of vitamin E TPGS as prepared by microfluidization technique initially showed slightly higher solubility compared with samples prepared by fusion method, but eventually it became the same as the study progressed. However, solid dispersion of solutol HS-15 as prepared by microfluidization demonstrated a significant, sustained increased in solubility over its sample when prepared by fusion method. Based on these results, we concluded that enhanced solubility using vitamin E TPGS and solutol HS-15 resulted from a partial conversion of crystalline drug to the amorphous form, increase in wettability of the drug by water soluble polymers, better separation of drug particles, micellar solubilization of drug by high concentrations of surfactant polymers, and interaction between polymer and drug at the molecular level.

A 5-day method for determination of soluble silicon concentrations in nonliquid fertilizer materials using a sodium carbonate-ammonium nitrate extractant followed by visible spectroscopy with heteropoly blue analysis: single-laboratory validation.

Science.gov (United States)

Sebastian, Dennis; Rodrigues, Hugh; Kinsey, Charles; Korndörfer, Gaspar; Pereira, Hamilton; Buck, Guilherme; Datnoff, Lawrence; Miranda, Stephen; Provance-Bowley, Mary

2013-01-01

A 5-day method for determining the soluble silicon (Si) concentrations in nonliquid fertilizer products was developed using a sodium carbonate (Na2CO3)-ammonium nitrate (NH4NO3) extractant followed by visible spectroscopy with heteropoly blue analysis at 660 nm. The 5-Day Na2CO3-NH4NO3 Soluble Si Extraction Method can be applied to quantify the plant-available Si in solid fertilizer products at levels ranging from 0.2 to 8.4% Si with an LOD of 0.06%, and LOQ of 0.20%. This Si extraction method for fertilizers correlates well with plant uptake of Si (r2 = 0.96 for a range of solid fertilizers) and is applicable to solid Si fertilizer products including blended products and beneficial substances. Fertilizer materials can be processed as received using commercially available laboratory chemicals and materials at ambient laboratory temperatures. The single-laboratory validation of the 5-Day Na2CO3-NH4NO3 Soluble Si Extraction Method has been approved by The Association of American Plant Food Control Officials for testing nonliquid Si fertilizer products.

The terminal solid solubility of hydrogen and deuterium in Zr-2.5Nb alloys

Energy Technology Data Exchange (ETDEWEB)

Ritchie, I G; Pan, Z L; Puls, M P [Atomic Energy of Canada Ltd., Pinawa, MB (Canada). Whiteshell Labs.

1997-02-01

The presence of hydrides in zirconium based alloys is an important factor in assessing the potential for delayed hydride cracking in pressure tubes and the embrittlement of other in-core components fabricated from these alloys. Consequently, the terminal solid solubility (TSS) of hydrogen in the zirconium alloys used in the Nuclear Industry is an important parameter. However, at the low hydrogen concentrations found in practice, the TSS is difficult to measure accurately and even the measurements of hydrogen concentrations by standard techniques are notoriously difficult to make reproducibly at the nominal levels found in pressure tube materials. The presence of hydrides, their dissolution and nucleation gives rise to a number of internal friction phenomena and changes in Young`s modulus that can be useful from the practical point of view. These phenomena can be used to establish expressions for the TSS as a function of temperature, the hysteresis between dissolution and nucleation and hydrogen supercharging from the gas phase. In particular, such studies show that the hysteresis between the TSS measured during heating and cooling is particularly sensitive to the thermal history of the sample. This paper reviews the phenomena involved and presents some recent results on Zr-2.5Nb pressure tube material. (author). 28 refs, 17 figs, 6 tabs.

Rheology of dilute acid hydrolyzed corn stover at high solids concentration.

Science.gov (United States)

Ehrhardt, M R; Monz, T O; Root, T W; Connelly, R K; Scott, C T; Klingenberg, D J

2010-02-01

The rheological properties of acid hydrolyzed corn stover at high solids concentration (20-35 wt.%) were investigated using torque rheometry. These materials are yield stress fluids whose rheological properties can be well represented by the Bingham model. Yield stresses increase with increasing solids concentration and decrease with increasing hydrolysis reaction temperature, acid concentration, and rheometer temperature. Plastic viscosities increase with increasing solids concentration and tend to decrease with increasing reaction temperature and acid concentration. The solids concentration dependence of the yield stress is consistent with that reported for other fibrous systems. The changes in yield stress with reaction conditions are consistent with observed changes in particle size. This study illustrates that torque rheometry can be used effectively to measure rheological properties of concentrated biomass.

SOLISOL-handling of solid solutions. Version 1.1

International Nuclear Information System (INIS)

Boerjesson, S.; Emren, A.

1992-09-01

SOLISOL is a C computer program designed to model geochemical reactions involving solid solutions. The program searches equilibrium concentrations of the components in the aqueous phase and the solid solution given by limited quantities of the solid solution components. The equilibrium code PHREEQE is used as a subprogram in SOLISOL. Subprograms external to PHREEQE extract information from PHREEQE results, take care of conserved properties, calculate solubilities and produce inputdata for PHREEQE. The essential idea in this process is to calculate solubilities for the components in terms of saturation indices, and give directions to PHREEQE on how to search for the equilibrium under those constraints. (au)

Solid dispersions, part II: new strategies in manufacturing methods for dissolution rate enhancement of poorly water-soluble drugs.

Science.gov (United States)

Bikiaris, Dimitrios N

2011-12-01

The absorption of poorly water-soluble drugs, when presented in the crystalline state to the gastrointestinal tract, is typically dissolution rate-limited, and according to BCS these drugs belong mainly to class II. Both dissolution kinetics and solubility are particle size dependent. Nowadays, various techniques are available to the pharmaceutical industry for dissolution rate enhancement of such drugs. Among such techniques, nanosuspensions and drug formulation in solid dispersions are those with the highest interest. This review discusses strategies undertaken over the last 10 years, which have been applied for the dissolution enhancement of poorly water-soluble drugs; such processes include melt mixing, electrospinning, microwave irradiation and the use of inorganic nanoparticles. Many problems in this field still need to be solved, mainly the use of toxic solvents, and for this reason the use of innovative new procedures and materials will increase over the coming years. Melt mixing remains extremely promising for the preparation of SDs and will probably become the most used method in the future for the preparation of solid drug dispersions.

Development of clinical dosage forms for a poorly water-soluble drug II: formulation and characterization of a novel solid microemulsion preconcentrate system for oral delivery of a poorly water-soluble drug.

Science.gov (United States)

Li, Ping; Hynes, Sara R; Haefele, Thomas F; Pudipeddi, Madhu; Royce, Alan E; Serajuddin, Abu T M

2009-05-01

The solution of a poorly water-soluble drug in a liquid lipid-surfactant mixture, which served as a microemulsion preconcentrate, was converted into a solid form by incorporating it in a solid polyethylene glycol (PEG) matrix. The solid microemulsion preconcentrates thus formed consisted of Capmul PG8 (propylene glycol monocaprylate) as oil, Cremophor EL (polyoxyl 35 castor oil) as surfactant, and hydrophilic polymer PEG 3350 as solid matrix. The drug (aqueous solubility: 0.17 microg/mL at pH 1-8 and 25 degrees C) was dissolved in a melt of the mixture at 65-70 degrees C and then the hot solution was filled into hard gelatin capsules; the liquid gradually solidified upon cooling below 55 degrees C. The solid system was characterized by differential scanning calorimetry (DSC), scanning electron microscopy (SEM), confocal Raman microscopy (CRM), and the dispersion testing in water. It was confirmed that a solid microemulsion preconcentrate is a two-phase system, where clusters of crystalline PEG 3350 formed the solid structure (m.p. 55-60 degrees C) and the liquid microemulsion preconcentrate dispersed in between PEG 3350 crystals as a separate phase. The drug remained dissolved in the liquid phase. In vitro release testing showed that the preconcentrate dispersed readily in water forming a microemulsion with the drug dissolved in the oil particles (PEG 3350 did not interfere with the process of self-microemulsification.

Measurement of soluble solids content in watermelon by Vis/NIR diffuse transmittance technique*

OpenAIRE

Tian, Hai-qing; Ying, Yi-bin; Lu, Hui-shan; Fu, Xia-ping; Yu, Hai-yan

2007-01-01

Watermelon is a popular fruit in the world with soluble solids content (SSC) being one of the major characteristics used for assessing its quality. This study was aimed at obtaining a method for nondestructive SSC detection of watermelons by means of visible/near infrared (Vis/NIR) diffuse transmittance technique. Vis/NIR transmittance spectra of intact watermelons were acquired using a low-cost commercially available spectrometer operating over the range 350~1000 nm. Spectra data were analyz...

Near Infrared Spectral Linearisation in Quantifying Soluble Solids Content of Intact Carambola

Directory of Open Access Journals (Sweden)

Mohd Zubir MatJafri

2013-04-01

Full Text Available This study presents a novel application of near infrared (NIR spectral linearisation for measuring the soluble solids content (SSC of carambola fruits. NIR spectra were measured using reflectance and interactance methods. In this study, only the interactance measurement technique successfully generated a reliable measurement result with a coefficient of determination of (R2 = 0.724 and a root mean square error of prediction for (RMSEP = 0.461° Brix. The results from this technique produced a highly accurate and stable prediction model compared with multiple linear regression techniques.

Near infrared spectral linearisation in quantifying soluble solids content of intact carambola.

Science.gov (United States)

Omar, Ahmad Fairuz; MatJafri, Mohd Zubir

2013-04-12

This study presents a novel application of near infrared (NIR) spectral linearisation for measuring the soluble solids content (SSC) of carambola fruits. NIR spectra were measured using reflectance and interactance methods. In this study, only the interactance measurement technique successfully generated a reliable measurement result with a coefficient of determination of (R2) = 0.724 and a root mean square error of prediction for (RMSEP) = 0.461° Brix. The results from this technique produced a highly accurate and stable prediction model compared with multiple linear regression techniques.

Solubility Enhancement and Formulation of Mouth Dissolving Tablet of Clonazepam with Solid Dispersion Technology

Directory of Open Access Journals (Sweden)

Swati C. Jagdale

2012-01-01

Full Text Available Clonazepam (CLZ is an anticonvulsant benzodiazepine widely used in the treatment of epilepsy. CLZ is a BCS Class II drug and its bioavailability is thus dissolution limited. The objective of the present study was to prepare solid dispersions (SDs of CLZ by various techniques, using the amphiphilic carrier Gelucire 50/13 in various proportions, to increase its water solubility. Drug-polymer interactions were investigated by Fourier-transform infrared (FTIR and UltraViolet (UV spectroscopy. The SDs were characterized physically by differential scanning calorimetry (DSC and X-ray diffraction (XRD. A phase solubility study was performed and the stability constant (Ks was found to be 275.27, while the negative Gibbs free energy (ΔGo tr indicated spontaneous solubilization of the drug. The dissolution study showed that the SDs considerably enhanced the dissolution rate of the drug. The FTIR and UV spectra revealed no chemical incompatibility between the drug and Gelucire 50/13. XRD patterns and the DSC profiles indicated the CLZ was in the amorphous form, which explains the improved dissolution rate of the drug from its SDs. Finally, mouth dissolving tablets (MDTs were prepared from the optimized batches (kneading method of solid dispersion, using crospovidone and Doshion P544 resin as superdisintegrants. The tablets were characterized by in-vitro disintegration and dissolution tests. The study of the MDTs showed disintegration times in the range 32.0±0.85 to 20.0±1.30 sec and dissolution was faster than for the commercial preparation. In conclusion, this investigation demonstrated the potential of solid dispersions of a drug with Gelucire 50/13 for promoting the dissolution of the drug and contributed to the understanding of the effect of a superdisintegrant on mouth dissolving tablets containing a solid dispersion of a hydrophobic drug.

Nanosilver and the microbiological activity of the particulate solids versus the leached soluble silver.

Science.gov (United States)

Faiz, Merisa B; Amal, Rose; Marquis, Christopher P; Harry, Elizabeth J; Sotiriou, Georgios A; Rice, Scott A; Gunawan, Cindy

2018-04-01

Nanosilver (Ag NPs) is currently one of the most commercialized antimicrobial nanoparticles with as yet, still unresolved cytotoxicity origins. To date, research efforts have mostly described the antimicrobial contribution from the leaching of soluble silver, while the undissolved solid Ag particulates are often considered as being microbiologically inert, serving only as source of the cytotoxic Ag ions. Here, we show the rapid stimulation of lethal cellular oxidative stress in bacteria by the presence of the undissolved Ag particulates. The cytotoxicity characteristics are distinct from those arising from the leached soluble Ag, the latter being locked in organic complexes. The work also highlights the unique oxidative stress-independent bacterial toxicity of silver salt. Taken together, the findings advocate that future enquiries on the antimicrobial potency and also importantly, the environmental and clinical impact of Ag NPs use, should pay attention to the potential bacterial toxicological responses to the undissolved Ag particulates, rather than just to the leaching of soluble silver. The findings also put into question the common use of silver salt as model material for evaluating bacterial toxicity of Ag NPs.

Major Source of Error in QSPR Prediction of Intrinsic Thermodynamic Solubility of Drugs: Solid vs Nonsolid State Contributions?

Science.gov (United States)

Abramov, Yuriy A

2015-06-01

The main purpose of this study is to define the major limiting factor in the accuracy of the quantitative structure-property relationship (QSPR) models of the thermodynamic intrinsic aqueous solubility of the drug-like compounds. For doing this, the thermodynamic intrinsic aqueous solubility property was suggested to be indirectly "measured" from the contributions of solid state, ΔGfus, and nonsolid state, ΔGmix, properties, which are estimated by the corresponding QSPR models. The QSPR models of ΔGfus and ΔGmix properties were built based on a set of drug-like compounds with available accurate measurements of fusion and thermodynamic solubility properties. For consistency ΔGfus and ΔGmix models were developed using similar algorithms and descriptor sets, and validated against the similar test compounds. Analysis of the relative performances of these two QSPR models clearly demonstrates that it is the solid state contribution which is the limiting factor in the accuracy and predictive power of the QSPR models of the thermodynamic intrinsic solubility. The performed analysis outlines a necessity of development of new descriptor sets for an accurate description of the long-range order (periodicity) phenomenon in the crystalline state. The proposed approach to the analysis of limitations and suggestions for improvement of QSPR-type models may be generalized to other applications in the pharmaceutical industry.

Actinide solubility in deep groundwaters - estimates for upper limits based on chemical equilibrium calculations

International Nuclear Information System (INIS)

Schweingruber, M.

1983-12-01

A chemical equilibrium model is used to estimate maximum upper concentration limits for some actinides (Th, U, Np, Pu, Am) in groundwaters. Eh/pH diagrams for solubility isopleths, dominant dissolved species and limiting solids are constructed for fixed parameter sets including temperature, thermodynamic database, ionic strength and total concentrations of most important inorganic ligands (carbonate, fluoride, phosphate, sulphate, chloride). In order to assess conservative conditions, a reference water is defined with high ligand content and ionic strength, but without competing cations. In addition, actinide oxides and hydroxides are the only solid phases considered. Recommendations for 'safe' upper actinide solubility limits for deep groundwaters are derived from such diagrams, based on the predicted Eh/pH domain. The model results are validated as far as the scarce experimental data permit. (Auth.)

Neptunium (IV) oxalate solubility

International Nuclear Information System (INIS)

Luerkens, D.W.

1983-07-01

The equilibrium solubility of neptunium (IV) oxalate in nitric/oxalic acid solutions was determined at 22 0 C, 45 0 C, and 60 0 C. The concentrations of nitric/oxalic acid solutions represented a wide range of free oxalate ion concentration. A mathematical solubility model was developed which is based on the formation of the known complexes of neptunium (IV) oxalate. the solubility model uses a simplified concentration parameter which is proportional to the free oxalate ion concentration. The solubility model can be used to estimate the equilibrium solubility of neptunium (IV) oxalate over a wide range of oxalic and nitric acid concentrations at each temperature

Significance of excipients to enhance the bioavailability of poorly water-soluble drugs in oral solid dosage forms: A Review

Science.gov (United States)

Vadlamudi, Manoj Kumar; Dhanaraj, Sangeetha

2017-11-01

Nowadays most of the drug substances are coming into the innovation pipeline with poor water solubility. Here, the influence of excipients will play a significant role to improve the dissolution of poorly aqueous soluble compounds. The drug substance needs to be dissolved in gastric fluids to get the better absorption and bioavailability of an orally administered drug. Dissolution is the rate-controlling stage for drugs which controls the rate and degree of absorption. Usually, poorly soluble oral administrated drugs show a slower dissolution rate, inconsistent and incomplete absorption which can lead to lower bioavailability. The low aqueous solubility of BCS class II and IV drugs is a major challenge in the drug development and delivery process. Several technologies have been used in an attempt to progress the bioavailability of poorly water-soluble drug compounds which include solid dispersions, lipid-based formulations, micronization, solvent evaporation, co-precipitation, ordered mixing, liquid-solid compacts, solvent deposition inclusion complexation, and steam aided granulation. In fact, most of the technologies require excipient as a carrier which plays a significant role in improving the bioavailability using Hypromellose acetate succinate, Cyclodextrin, Povidone, Copovidone, Hydroxypropyl cellulose, Hydroxypropyl methylcellulose, Crospovidone, Starch, Dimethylacetamide, Polyethylene glycol, Sodium lauryl sulfate, Polysorbate, Poloxamer. Mesoporous silica and so on. This review deliberates about the excipients significance on bioavailability enhancement of drug products in a single platform along with pragmatically proved applications so that user can able to select the right excipients as per the molecule.

Solubility of plutonium and waste evaporation

International Nuclear Information System (INIS)

Karraker, D.G.

1993-01-01

Chemical processing of irradiated reactor elements at the Savannah River Site separates uranium, plutonium and fission products; fission products and process-added chemicals are mixed with an excess of NaOH and discharged as a basic slurry into large underground tanks for temporary storage. The slurry is composed of base-insoluble solids that settle to the bottom of the tank; the liquid supemate contains a mixture of base-soluble chemicals--nitrates, nitrites aluminate, sulfate, etc. To conserve space in the waste tanks, the supemate is concentrated by evaporation. As the evaporation proceeds, the solubilities of some components are exceeded, and these species crystallize from solution. Normally, these components are soluble in the hot solution discharged from the waste tank evaporator and do not crystallize until the solution cools. However, concern was aroused at West Valley over the possibility that plutonium would precipitate and accumulate in the evaporator, conceivably to the point that a nuclear accident was possible. There is also a concern at SRS from evaporation of sludge washes, which arise from washing the base-insoluble solids (open-quote sludge close-quote) with ca. 1M NaOH to reduce the Al and S0 4 -2 content. The sludge washes of necessity extract a low level of Pu from the sludge and are evaporated to reduce their volume, presenting the possibility of precipitating Pu. Measurements of the solubility of Pu in synthetic solutions of similar composition to waste supernate and sludge washes are described in this report

Solubility of chromate in a hydrated OPC

International Nuclear Information System (INIS)

Leisinger, Sabine M.; Bhatnagar, Amit; Lothenbach, Barbara; Johnson, C. Annette

2014-01-01

Highlights: • Solid solutions exist between gypsum and calcium chromate. • The cementitious matrix can bind chromate concentrations up to 0.1 mol/kg. • The chromate binding phase in the cementitious matrix is CrO 4 -ettringite. - Abstract: The knowledge of the chromate binding mechanisms is essential for the prediction of the long-term leachability of cement-based solidified waste containing increased chromate concentrations because of its toxicity and high mobility. In this paper pore water concentrations from OPC doped with varying CaCrO 4 concentrations (0.01–0.8 mol/kg), equilibrated for 28 days were reported. It could be shown that the cementitious matrix can bind chromate concentrations up to 0.1 mol/kg and that the chromate solubility limiting phase was CrO 4 -ettringite, while chromate containing AFm (monochromate) was unstable. Comparison with thermodynamic modelling indicated that at lower chromate dosages chromate was mainly bound by CrO 4 -ettringite while at very high dosages also a mixed CaCrO 4 –CaSO 4 ·2H 2 O phase precipitated. Additional experiments indicated a solubility product of 10 −3.66 for CaCrO 4 and verified the solid solution formation with CaSO 4 ·2H 2 O. Leaching tests indicated a strong chromate binding mainly in the pH range 10.5–13.5, while at pH < 10 very little chromate was bound as ettringite, monocarbonate and C–S–H phases were destabilized. Generally the thermodynamic modeling underestimated chromate uptake indicating that an additional chromate binding possibly on C–S–H or on mixed chromate–carbonate–hydroxide AFm phases

Production of a water-soluble fertilizer containing amino acids by solid-state fermentation of soybean meal and evaluation of its efficacy on the rapeseed growth.

Science.gov (United States)

Wang, Jianlei; Liu, Zhemin; Wang, Yue; Cheng, Wen; Mou, Haijin

2014-10-10

Soybean meal is a by-product of soybean oil extraction and contains approximately 44% protein. We performed solid-state fermentation by using Bacillus subtilis strain N-2 to produce a water-soluble fertilizer containing amino acids. Strain N-2 produced a high yield of protease, which transformed the proteins in soybean meal into peptide and free amino acids that were dissolved in the fermentation products. Based on the Plackett-Burman design, the initial pH of the fermentation substrate, number of days of fermentation, and the ratio of liquid to soybean meal exhibited significant effects on the recovery of proteins in the resulting water-soluble solution. According to the predicted results of the central composite design, the highest recovery of soluble proteins (99.072%) was achieved at the optimum conditions. Under these conditions, the resulting solution contained 50.42% small peptides and 7.9% poly-γ-glutamic acid (γ-PGA). The water-soluble fertilizer robustly increased the activity of the rapeseed root system, chlorophyll content, leaf area, shoot dry weight, root length, and root weight at a concentration of 0.25% (w/v). This methodology offers a value-added use of soybean meal. Copyright © 2014 Elsevier B.V. All rights reserved.

An experimental study on MRI signal intensity vs concentration of water-soluble contrast media

International Nuclear Information System (INIS)

Lee, Ghi Jai; Han, Chang Yul; Chang, Kee Hyun; Han, Moon Hee; Han, Man Chung

1991-01-01

There has been only one report that water-soluble contrast media containing iodine and used in conventional X -ray radiography reduce T1-and T2-relaxation times. We evaluated the relationship between signal intensity (relative signal intensity to normal saline) and T2-relaxation time of MRI and the concentration of 3 water-soluble contrast media [meglumine ioxithalamate (Telebrix 30), iopromide (Ultravist 300), iotrolan (Isovist 300)] through the phantom study, using both 2.0T and 0.5T MR units. We found that the signal intensity increased significantly on the T1-weighted images as the concentration of contrast media increased. The degree of the increase was larger on 0.5T MR than on 2.0T MR. The signal intensity on proton density image showed no significant difference at various concentrations. However, there were significant decreases of both signal intensity on the T2-weighted images and T2-relaxation time as the concentration of contrast media increased, which was more prominent on 2.0T MR than 0.5T MR. Between the contrast media of the same concentration, there was no significant difference in signal intensity and T2-relaxation time

Importance of critical micellar concentration for the prediction of solubility enhancement in biorelevant media.

Science.gov (United States)

Ottaviani, G; Wendelspiess, S; Alvarez-Sánchez, R

2015-04-06

This study evaluated if the intrinsic surface properties of compounds are related to the solubility enhancement (SE) typically observed in biorelevant media like fasted state simulated intestinal fluids (FaSSIF). The solubility of 51 chemically diverse compounds was measured in FaSSIF and in phosphate buffer and the surface activity parameters were determined. This study showed that the compound critical micellar concentration parameter (CMC) correlates strongly with the solubility enhancement (SE) observed in FaSSIF compared to phosphate buffer. Thus, the intrinsic capacity of molecules to form micelles is also a determinant for each compound's affinity to the micelles of biorelevant surfactants. CMC correlated better with SE than lipophilicity (logD), especially over the logD range typically covered by drugs (2 < logD < 4). CMC can become useful to guide drug discovery scientists to better diagnose, improve, and predict solubility in biorelevant media, thereby enhancing oral bioavailability of drug candidates.

Solid dispersions of Myricetin with enhanced solubility: Formulation, characterization and crystal structure of stability-impeding Myricetin monohydrate crystals

Science.gov (United States)

Mureşan-Pop, M.; Pop, M. M.; Borodi, G.; Todea, M.; Nagy-Simon, T.; Simon, S.

2017-08-01

Three solid dispersion forms of Myricetin combined with the Polyvinylpyrrolidone were successfully prepared by spray drying method, and characterized by X-ray powder diffraction, thermal analysis, infrared spectroscopy and optical microscopy. Zeta potential measurements provided indications on solid dispersions stability in aqueous suspension related to their storage at elevated temperature and relative humidity, which depends on the Myricetin load. By increase of Myricetin load, the stability of the solid dispersion is impeded due to growth of Myricetin monohydrate crystals. The amorphous dispersions with 10% and 50% Myricetin load are stable and, compared to pure Myricetin, their aqueous solubility is enhanced by a factor of 47 and 13, respectively. The dispersion with 80% Myricetin load is unstable on storage, and this behavior acts in conjunction with the development of Myricetin monohydrate crystals. Single-crystal X-ray diffraction results obtained for Myricetin monohydrate reveal a structure of an infinite 2D network of hydrogen-bonded molecules involving all six hydroxyl groups of Myricetin. The water molecules are positioned in between the infinite chains, and contribute via H-bonds to robust crystal packing. The calculated needle-like morphology of monohydrate form is in agreement with the optical microscopy results. The study shows that the solid amorphous dispersions with up to 50% Myricetin load are a viable option for achieving substantial solubility improvement of Myricetin, and supports their potential use in pharmaceutical applications.

Solid solubility of fission product and other transition elements in carbides and nitrides of uranium and plutonium

International Nuclear Information System (INIS)

Benedict, U.

1979-01-01

Solubility studies were made in some MX-Me systems (M:U or Pu; X: C or N; Me: fission product or other transition element) by X-ray diffraction and partly by microprobe determination of solute concentrations. Up to 23 m/o ZrC and 17 m/o TaC dissolved in the PuC phases of sintered PuC-ZrC and PuC-TaC samples; the lattice parameter/concentration relationships were derived. The relative lattice parameter difference (RLPD) between MXy and MeXy (y: ratio X/(M+Me)) was used as a solubility criterion. NaCl type monocarbides with RLPD's from -10.2% to +7.8% are completely miscible with UC and PuC. NaCl type mononitrides with RLPD's from -7.5% to 8.5% are completely miscible with UN and PuN. The solubility in the sesquicarbides increases with decreasing RLPD and becomes complete in Pu 2 C 3 at RLPD =+4%, and in U 2 C 3 at RLPD ca. +1.5%. Solubilities are predicted on the basis of these rules for the cases where no experimental results are available. A general review on the experimental and predicted solubilities is given. (orig.) [de

Solids-based concentrated solar power receiver

Science.gov (United States)

None

2018-04-10

A concentrated solar power (CSP) system includes channels arranged to convey a flowing solids medium descending under gravity. The channels form a light-absorbing surface configured to absorb solar flux from a heliostat field. The channels may be independently supported, for example by suspension, and gaps between the channels are sized to accommodate thermal expansion. The light absorbing surface may be sloped so that the inside surfaces of the channels proximate to the light absorbing surface define downward-slanting channel floors, and the flowing solids medium flows along these floors. Baffles may be disposed inside the channels and oriented across the direction of descent of the flowing solids medium. The channels may include wedge-shaped walls forming the light-absorbing surface and defining multiple-reflection light paths for solar flux from the heliostat field incident on the light-absorbing surface.

Differential solubility of curcuminoids in serum and albumin solutions: implications for analytical and therapeutic applications

Directory of Open Access Journals (Sweden)

Quitschke Wolfgang W

2008-11-01

Full Text Available Abstract Background Commercially available curcumin preparations contain a mixture of related polyphenols, collectively referred to as curcuminoids. These encompass the primary component curcumin along with its co-purified derivatives demethoxycurcumin and bisdemethoxycurcumin. Curcuminoids have numerous biological activities, including inhibition of cancer related cell proliferation and reduction of amyloid plaque formation associated with Alzheimer disease. Unfortunately, the solubility of curcuminoids in aqueous solutions is exceedingly low. This restricts their systemic availability in orally administered formulations and limits their therapeutic potential. Results Methods are described that achieve high concentrations of soluble curcuminoids in serum. Solid curcuminoids were either mixed directly with serum, or they were predissolved in dimethyl sulfoxide and added as aliquots to serum. Both methods resulted in high levels of curcuminoid-solubility in mammalian sera from different species. However, adding aliquots of dimethyl sulfoxide-dissolved curcuminoids to serum proved to be more efficient, producing soluble curcuminoid concentrations of at least 3 mM in human serum. The methods also resulted in the differential solubility of individual curcuminoids in serum. The addition of dimethyl sulfoxide-dissolved curcuminoids to serum preferentially solubilized curcumin, whereas adding solid curcuminoids predominantly solubilized bisdemethoxycurcumin. Either method of solubilization was equally effective in inhibiting dose-dependent HeLa cell proliferation in culture. The maximum concentration of curcuminoids achieved in serum was at least 100-fold higher than that required for inhibiting cell proliferation in culture and 1000-fold higher than the concentration that has been reported to prevent amyloid plaque formation associated with Alzheimer disease. Curcuminoids were also highly soluble in solutions of purified albumin, a major component of

Solid solubility, phase transitions, thermal expansion, and compressibility in Sc{sub 1−x}Al{sub x}F{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Morelock, Cody R.; Gallington, Leighanne C. [School of Chemistry and Biochemistry, Georgia Institute of Technology, Atlanta, GA 30332-0400 (United States); Wilkinson, Angus P., E-mail: angus.wilkinson@chemistry.gatech.edu [School of Chemistry and Biochemistry, Georgia Institute of Technology, Atlanta, GA 30332-0400 (United States); School of Materials Science and Engineering, Georgia Institute of Technology, Atlanta, GA 30332-0245 (United States)

2015-02-15

With the goal of thermal expansion control, the synthesis and properties of Sc{sub 1−x}Al{sub x}F{sub 3} were investigated. The solubility limit of AlF{sub 3} in ScF{sub 3} at ∼1340 K is ∼50%. Solid solutions (x≤0.50) were characterized by synchrotron powder diffraction at ambient pressure between 100 and 900 K and at pressures <0.414 GPa while heating from 298 to 523 K. A phase transition from cubic to rhombohedral is observed. The transition temperature increases smoothly with Al{sup 3+} content, approaching 500 K at the solid solubility limit, and also upon compression at fixed Al{sup 3+} content. The slope of the pressure–temperature phase boundary is ∼0.5 K MPa{sup −1}, which is steep relative to that for most symmetry-lowering phase transitions in perovskites. The volume coefficient of thermal expansion (CTE) for the rhombohedral phase is strongly positive, but the cubic-phase CTE varies from negative (x<0.15) to near-zero (x=0.15) to positive (x>0.20) between ∼600 and 800 K. The cubic solid solutions elastically stiffen on heating, while Al{sup 3+} substitution causes softening at a given temperature. - Graphical abstract: The cubic-phase coefficient of thermal expansion for Sc{sub 1−x}Al{sub x}F{sub 3}(solubility limit ∼50% at ∼1340 K) becomes more positive with increased Al{sup 3+} substitution, but the average isothermal bulk modulus decreases (elastic softening). - Highlights: • The solubility limit of AlF{sub 3} in ScF{sub 3} at ∼1340 K is ∼50%. • The phase transition temperature of Sc{sub 1−x}Al{sub x}F{sub 3} increases smoothly with x. • The cubic-phase volume CTE varies from negative to positive with increasing x. • The cubic solid solutions elastically stiffen on heating. • Al{sup 3+} substitution causes softening at a given temperature.

Hyperspectral Imaging Coupled with Random Frog and Calibration Models for Assessment of Total Soluble Solids in Mulberries

Directory of Open Access Journals (Sweden)

Yan-Ru Zhao

2015-01-01

Full Text Available Chemometrics methods coupled with hyperspectral imaging technology in visible and near infrared (Vis/NIR region (380–1030 nm were introduced to assess total soluble solids (TSS in mulberries. Hyperspectral images of 310 mulberries were acquired by hyperspectral reflectance imaging system (512 bands and their corresponding TSS contents were measured by a Brix meter. Random frog (RF method was used to select important wavelengths from the full wavelengths. TSS values in mulberry fruits were predicted by partial least squares regression (PLSR and least-square support vector machine (LS-SVM models based on full wavelengths and the selected important wavelengths. The optimal PLSR model with 23 important wavelengths was employed to visualise the spatial distribution of TSS in tested samples, and TSS concentrations in mulberries were revealed through the TSS spatial distribution. The results declared that hyperspectral imaging is promising for determining the spatial distribution of TSS content in mulberry fruits, which provides a reference for detecting the internal quality of fruits.

Influence of solids retention time on membrane fouling: characterization of extracellular polymeric substances and soluble microbial products.

Science.gov (United States)

Duan, Liang; Tian, Zhiyong; Song, Yonghui; Jiang, Wei; Tian, Yuan; Li, Shan

2015-01-01

The objective of this study was to investigate the influence of solids retention time (SRT) on membrane fouling and the characteristics of biomacromolecules. Four identical laboratory-scale membrane bioreactors (MBRs) were operated with SRTs for 10, 20, 40 and 80 days. The results indicated that membrane fouling occurred faster and more readily under short SRTs. Fouling resistance was the primary source of filtration resistance. The modified fouling index (MFI) results suggested that the more ready fouling at short SRTs could be attributed to higher concentrations of soluble microbial products (SMP). Fourier transform infrared (FTIR) spectra indicated that the SRT had a weak influence on the functional groups of the total extracellular polymeric substances (TEPS) and SMP. However, the MBR under a short SRT had more low-molecular-weight (MW) compounds (100 kDa). Aromatic protein and tryptophan protein-like substances were the dominant groups in the TEPS and SMP, respectively.

Wax encapsulation of water-soluble compounds for application in foods.

Science.gov (United States)

Mellema, M; Van Benthum, W A J; Boer, B; Von Harras, J; Visser, A

2006-11-01

Water-soluble ingredients have been successfully encapsulated in wax using two preparation techniques. The first technique ('solid preparation') leads to relatively large wax particles. The second technique ('liquid preparation') leads to relatively small wax particles immersed in vegetable oil. On the first technique: stable encapsulation of water-soluble colourants (dissolved at low concentration in water) has been achieved making use of beeswax and PGPR. The leakage from the capsules, for instance of size 2 mm, is about 30% after 16 weeks storage in water at room temperature. To form such capsules a minimum wax mass of 40% relative to the total mass is needed. High amounts of salt or acids at the inside water phase causes more leaking, probably because of the osmotic pressure difference. Osmotic matching of inner and outer phase can lead to a dramatic reduction in leakage. Fat capsules are less suitable to incorporate water soluble colourants. The reason for this could be a difference in crystal structure (fat is less ductile and more brittle). On the second technique: stable encapsulation of water-soluble colourants (encapsulated in solid wax particles) has been achieved making use of carnauba wax. The leakage from the capsules, for instance of size 250 mm, is about 40% after 1 weeks storage in water at room temperature.

Effects of thermal processing by nanofluids on vitamin C, total phenolics and total soluble solids of tomato juice.

Science.gov (United States)

Jafari, S M; Jabari, S S; Dehnad, D; Shahidi, S A

2017-03-01

In this research, our main idea was to apply thermal processing by nanofluids instead of conventional pasteurization processes, to shorten duration of thermal procedure and improve nutritional contents of fruit juices. Three different variables of temperature (70, 80 and 90 °C), nanofluid concentration (0, 2 and 4%) and time (30, 60 and 90 s) were selected for thermal processing of tomato juices by a shell and tube heat exchanger. The results demonstrated that 4% nanofluid concentration, at 30 °C for 30 s could result in 66% vitamin C retention of fresh juice while it was about 56% for the minimum nanofluid concentration and maximum temperature and time. Higher nanoparticle concentrations made tomato juices that require lowered thermal durations, because of better heat transfer to the product, and total phenolic compounds dwindle less severely; In fact, after 30 s thermal processing at 70 °C with 0 and 4% nanoparticles, total phenolic compounds were maintained by 71.9 and 73.6%, respectively. The range of total soluble solids for processed tomato juices was 5.4-5.6, meaning that nanofluid thermal processing could preserve the natural condition of tomato juices successfully. Based on the indices considered, a nanofluid thermal processing with 4% nanoparticle concentration at the temperature of 70 °C for 30 s will result in the best nutritional contents of final tomato juices.

Solubility of Nd in brine

International Nuclear Information System (INIS)

Khalili, F.I.; Symeopoulos, V.; Chen, J.F.; Choppin, G.R.

1994-01-01

The solubility of Nd(III) has been measured at 23±3 C in a synthetic brine at pcH 6.4, 8.4, 10.4 and 12.4. The brine consisted predominantly of (Na+K)Cl and MgCl 2 with an ionic strength of 7.8 M (9.4 m) a solid compound of Nd(III) at each pcH was assigned from X-ray diffraction patterns. The log values of the experimental solubilities decrease fomr -3 at pcH 6.4 to -5.8 at pcH 8.4; at pcH 10.4 and 12.4 the solubility was below the detection limit of -7.5. The experimental solubility does not follow closely the variation with pcH estimated from modeling of the species in solution in equilibrium with the Nd solid using S.I.T. (orig.)

Consumption of a dietary portfolio of cholesterol lowering foods improves blood lipids without affecting concentrations of fat soluble compounds.

Science.gov (United States)

Ramprasath, Vanu R; Jenkins, David J A; Lamarche, Benoit; Kendall, Cyril W C; Faulkner, Dorothea; Cermakova, Luba; Couture, Patrick; Ireland, Chris; Abdulnour, Shahad; Patel, Darshna; Bashyam, Balachandran; Srichaikul, Korbua; de Souza, Russell J; Vidgen, Edward; Josse, Robert G; Leiter, Lawrence A; Connelly, Philip W; Frohlich, Jiri; Jones, Peter J H

2014-10-18

Consumption of a cholesterol lowering dietary portfolio including plant sterols (PS), viscous fibre, soy proteins and nuts for 6 months improves blood lipid profile. Plant sterols reduce blood cholesterol by inhibiting intestinal cholesterol absorption and concerns have been raised whether PS consumption reduces fat soluble vitamin absorption. The objective was to determine effects of consumption of a cholesterol lowering dietary portfolio on circulating concentrations of PS and fat soluble vitamins. Using a parallel design study, 351 hyperlipidemic participants from 4 centres across Canada were randomized to 1 of 3 groups. Participants followed dietary advice with control or portfolio diet. Participants on routine and intensive portfolio involved 2 and 7 clinic visits, respectively, over 6 months. No changes in plasma concentrations of α and γ tocopherol, lutein, lycopene and retinol, but decreased β-carotene concentrations were observed with intensive (week 12: p = 0.045; week 24: p = 0.039) and routine (week 12: p = 0.031; week 24: p = 0.078) portfolio groups compared to control. However, cholesterol adjusted β-carotene and fat soluble compound concentrations were not different compared to control. Plasma PS concentrations were increased with intensive (campesterol:p = 0.012; β-sitosterol:p = 0.035) and routine (campesterol: p = 0.034; β-sitosterol: p = 0.080) portfolio groups compared to control. Plasma cholesterol-adjusted campesterol and β-sitosterol concentrations were negatively correlated (p portfolio diet reduces serum total and LDL-C levels while increasing PS values, without altering fat soluble compounds concentrations. The extent of increments of PS with the current study are not deleterious and also maintaining optimum levels of fat soluble vitamins are of paramount necessity to maintain overall metabolism and health. Results indicate portfolio diet as one of the best options for CVD risk reduction

Dual Activity of Hydroxypropyl-β-Cyclodextrin and Water-Soluble Carriers on the Solubility of Carvedilol.

Science.gov (United States)

Zoghbi, Abdelmoumin; Geng, Tianjiao; Wang, Bo

2017-11-01

Carvedilol (CAR) is a non-selective α and β blocker categorized as class II drug with low water solubility. Several recent studies have investigated ways to overcome this problem. The aim of the present study was to combine two of these methods: the inclusion complex using hydroxypropyl-β-cyclodextrin (HPβCD) with solid dispersion using two carriers: Poloxamer 188 (PLX) and Polyvinylpyrrolidone K-30 (PVP) to enhance the solubility, bioavailability, and the stability of CAR. Kneading method was used to prepare CAR-HPβCD inclusion complex (KD). The action of different carriers separately and in combination on Carvedilol solubility was investigated in three series. CAR-carrier and KD-carrier solid dispersions were prepared by solvent evaporation method. In vitro dissolution test was conducted in three different media: double-distilled water (DDW), simulative gastric fluid (SGF), and PBS pH 6.8 (PBS). The interactions between CAR, HPβCD, and different carriers were explored by Fourier transform infrared spectroscopy (FTIR), powder X-ray diffractometry (XRD), and differential scanning colorimetry (DSC). The results showed higher solubility of CAR in KD-PVP solid dispersions up to 70, 25, and 22 fold compared to pure CAR in DDW, SGF, and PBS, respectively. DSC and XRD analyses indicated an improved degree of transformation of CAR in KD-PVP solid dispersion from crystalline to amorphous state. This study provides a new successful combination of two polymers with the dual action of HPβCD and PLX/PVP on water solubility and bioavailability of CAR.

Thermodynamic data development using the solubility method (Joint research)

International Nuclear Information System (INIS)

Rai, Dhanpat; Yui, Mikazu

2013-05-01

The solubility method is one of the most powerful tools to obtain reliable thermodynamic data for 1) solubility products of discrete solids and double salts, 2) complexation constants for various ligands, 3) development of data in a wide range of pH values, 4) evaluation of data for metals that form very insoluble solids (e.g. tetravalent actinides), 5) determining solubility-controlling solids in different types of wastes and 6) elevated temperatures for redox sensitive systems. This document is focused on describing various aspects of obtaining thermodynamic data using the solubility method. This manuscript deals with various aspects of conducting solubility studies, including selecting the study topic, modeling to define important variables, selecting the range of variables and experimental parameters, anticipating results, general equipment requirements, conducting experiments, and interpreting experimental data. (author)

Solubility of nickel ferrite (NiFe2O4) from 100 to 200 deg. C

International Nuclear Information System (INIS)

Bellefleur, Alexandre; Bachet, Martin; Benezeth, Pascale; Schott, Jacques

2012-09-01

The solubility of nickel ferrite was measured in a Hydrogen-Electrode Concentration Cell (HECC) at temperatures of 100 deg. C, 150 deg. C and 200 deg. C and pH between 4 and 5.25. The experimental solution was composed of HCl and NaCl (0.1 mol.L -1 ). Based on other studies ([1,2]), pure nickel ferrite was experimentally synthesized by calcination of a mixture of hematite Fe 2 O 3 and bunsenite NiO in molten salts at 1000 deg. C for 15 hours in air. The so obtained powder was fully characterized. The Hydrogen-Electrode Concentration cell has been described in [3]. It allowed us to run solubility experiments up to 250 deg. C with an in-situ pH measurement. To avoid reduction of the solid phase to metallic nickel, a hydrogen/argon mixture was used instead of pure hydrogen. Consequently, the equilibration time for the electrodes was longer than with pure hydrogen. Eight samples were taken on a 70 days period. After the experiments, the powder showed no significant XRD evidence of Ni (II) reduction. Nickel concentration was measured by atomic absorption spectroscopy and iron concentration was measured by UV spectroscopy. The protocol has been designed to be able to measure both dissolved Fe (II) and total iron. The nickel solubility of nickel ferrite was slightly lower than the solubility of nickel oxide in close experimental conditions [3]. Dissolved iron was mainly ferrous and the solution was under-saturated relative to both hematite and magnetite. The nickel/iron ratio indicated a non-stoichiometric dissolution. The solubility measurements were compared with equilibrium calculations using the MULTEQ database. [1] Hayashi et al (1980) J. Materials Sci. 15, 1491-1497. [2] Ziemniak et al (2007) J. Physics and Chem. of Solids. 68,10-21. [3] EPRI Report 1003155 (2002). (authors)

Hansen solubility parameters (HSP) for prescreening formulation of solid lipid nanoparticles (SLN): in vitro testing of curcumin-loaded SLN in MCF-7 and BT-474 cell lines.

Science.gov (United States)

Doktorovova, Slavomira; Souto, Eliana B; Silva, Amélia M

2018-01-01

Curcumin, a phenolic compound from turmeric rhizome (Curcuma longa), has many interesting pharmacological effects, but shows very low aqueous solubility. Consequently, several drug delivery systems based on polymeric and lipid raw materials have been proposed to increase its bioavailability. Solid lipid nanoparticles (SLN), consisting of solid lipid matrix and a surfactant layer can load poorly water-soluble drugs, such as curcumin, deliver them at defined rates and enhance their intracellular uptake. In the present work, we demonstrate that, despite the drug's affinity to lipids frequently used in SLN production, the curcumin amount loaded in most SLN formulations may be too low to exhibit anticancer properties. The predictive curcumin solubility in solid lipids has been thoroughly analyzed by Hansen solubility parameters, in parallel with the lipid-screening solubility tests for a range of selected lipids. We identified the most suitable lipid materials for curcumin-loaded SLN, producing physicochemically stable particles with high encapsulation efficiency (>90%). Loading capacity of curcumin in SLN allowed preventing the cellular damage caused by cationic SLN on MCF-7 and BT-474 cells but was not sufficient to exhibit drug's anticancer properties. But curcumin-loaded SLN exhibited antioxidant properties, substantiating the conclusions that curcumin's effect in cancer cells is highly dose dependent.

Mathematical model to analyze the dissolution behavior of metastable crystals or amorphous drug accompanied with a solid-liquid interface reaction.

Science.gov (United States)

Hirai, Daiki; Iwao, Yasunori; Kimura, Shin-Ichiro; Noguchi, Shuji; Itai, Shigeru

2017-04-30

Metastable crystals and the amorphous state of poorly water-soluble drugs in solid dispersions (SDs), are subject to a solid-liquid interface reaction upon exposure to a solvent. The dissolution behavior during the solid-liquid interface reaction often shows that the concentration of drugs is supersaturated, with a high initial drug concentration compared with the solubility of stable crystals but finally approaching the latter solubility with time. However, a method for measuring the precipitation rate of stable crystals and/or the potential solubility of metastable crystals or amorphous drugs has not been established. In this study, a novel mathematical model that can represent the dissolution behavior of the solid-liquid interface reaction for metastable crystals or amorphous drug was developed and its validity was evaluated. The theory for this model was based on the Noyes-Whitney equation and assumes that the precipitation of stable crystals at the solid-liquid interface occurs through a first-order reaction. Moreover, two models were developed, one assuming that the surface area of the drug remains constant because of the presence of excess drug in the bulk and the other that the surface area changes in time-dependency because of agglomeration of the drug. SDs of Ibuprofen (IB)/polyvinylpyrrolidone (PVP) were prepared and their dissolution behaviors under non-sink conditions were fitted by the models to evaluate improvements in solubility. The model assuming time-dependent surface area showed good agreement with experimental values. Furthermore, by applying the model to the dissolution profile, parameters such as the precipitation rate and the potential solubility of the amorphous drug were successfully calculated. In addition, it was shown that the improvement in solubility with supersaturation was able to be evaluated quantitatively using this model. Therefore, this mathematical model would be a useful tool to quantitatively determine the supersaturation

Recovery of soluble chloride salts from the wastewater generated during the washing process of municipal solid wastes incineration fly ash.

Science.gov (United States)

Tang, Hailong; Erzat, Aris; Liu, Yangsheng

2014-01-01

Water washing is widely used as the pretreatment method to treat municipal solid waste incineration fly ash, which facilitates the further solidification/stabilization treatment or resource recovery of the fly ash. The wastewater generated during the washing process is a kind of hydrosaline solution, usually containing high concentrations of alkali chlorides and sulphates, which cause serious pollution to environment. However, these salts can be recycled as resources instead of discharge. This paper explored an effective and practical recovery method to separate sodium chloride, potassium chloride, and calcium chloride salts individually from the hydrosaline water. In laboratory experiments, a simulating hydrosaline solution was prepared according to composition of the waste washing water. First, in the three-step evaporation-crystallization process, pure sodium chloride and solid mixture of sodium and potassium chlorides were obtained separately, and the remaining solution contained potassium and calcium chlorides (solution A). And then, the solid mixture was fully dissolved into water (solution B obtained). Finally, ethanol was added into solutions A and B to change the solubility of sodium, potassium, and calcium chlorides within the mixed solvent of water and ethanol. During the ethanol-adding precipitation process, each salt was separated individually, and the purity of the raw production in laboratory experiments reached about 90%. The ethanol can be recycled by distillation and reused as the solvent. Therefore, this technology may bring both environmental and economic benefits.

Enhancement of solubility and oral bioavailability of manidipine by formation of ternary solid dispersion with d-α-tocopherol polyethylene glycol 1000 succinate and copovidone.

Science.gov (United States)

Chamsai, Benchawan; Limmatvapirat, Sontaya; Sungthongjeen, Srisagul; Sriamornsak, Pornsak

2017-12-01

Low bioavailability of oral manidipine (MDP) is due to its low water solubility. The objective of this study was to increase the solubility and bioavailability of MDP by fabricating ternary solid dispersion (tSD) with d-α-tocopherol polyethyleneglycol-1000-succinate and copovidone. In this study, solid ternary phase diagram was applied in order to check the homogeneity of tSD prepared by melting and solidifying with dry ice. The physicochemical properties of different formulations were determined by differential scanning calorimetry (DSC), powder X-ray diffraction (PXRD), Fourier transform infrared spectroscopy (FTIR) and hot stage microscopy. Their solubility, dissolution, stability and bioavailability were also investigated. The results demonstrated that tSD obtained from ternary phase diagram divided into homogeneous and non-homogeneous regions. In the homogenous region, the transparent characteristics of tSD was observed and considered as a glass solution, which have a higher MDP solubility than that in non-homogenous region. The hot stage microscopy, DSC and PXRD confirmed that solid dispersion was formed in which MDP was molecularly dispersed in the carriers, especially in the homogenous region of phase diagram. FTIR analysis demonstrated strong hydrogen bonding between amine groups of MDP and carbonyl groups of copovidone, which supported a higher solubility and dissolution of tSD. The pharmacokinetic study in Wistar rats showed that the tSD had the greatest effect on oral bioavailability. Immediate hypotensive effect of tSD was also observed in vivo. The improvement of stability, dissolution and oral bioavailability of MDP could be achieved by using tSD technique.

Solubility behavior and biopharmaceutical classification of novel high-solubility ciprofloxacin and norfloxacin pharmaceutical derivatives.

Science.gov (United States)

Breda, Susana A; Jimenez-Kairuz, Alvaro F; Manzo, Ruben H; Olivera, María E

2009-04-17

The hydrochlorides of the 1:3 aluminum:norfloxacin and aluminum:ciprofloxacin complexes were characterized according to the Biopharmaceutics Classification System (BCS) premises in comparison with their parent compounds. The pH-solubility profiles of the complexes were experimentally determined at 25 and 37 degrees C in the range of pH 1-8 and compared to that of uncomplexed norfloxacin and ciprofloxacin. Both complexes are clearly more soluble than the antibiotics themselves, even at the lowest solubility pHs. The increase in solubility was ascribed to the species controlling solubility, which were analyzed in the solid phases at equilibrium at selected pHs. Additionally, permeability was set as low, based on data reported in the scientific literature regarding oral bioavailability, intestinal and cell cultures permeabilities and also considering the influence of stoichiometric amounts of aluminum. The complexes fulfill the BCS criterion to be classified as class 3 compounds (high solubility/low permeability). Instead, the active pharmaceutical ingredients (APIs) currently used in solid dosage forms, norfloxacin and ciprofloxacin hydrochloride, proved to be BCS class 4 (low solubility/low permeability). The solubility improvement turns the complexes as potential biowaiver candidates from the scientific point of view and may be a good way for developing more dose-efficient formulations. An immediate release tablet showing very rapid dissolution was obtained. Its dissolution profile was compared to that of the commercial ciprofloxacin hydrochloride tablets allowing to dissolution of the complete dose at a critical pH such as 6.8.

Solubility of Carbon in Nanocrystalline -Iron

OpenAIRE

Alexander Kirchner; Bernd Kieback

2012-01-01

A thermodynamic model for nanocrystalline interstitial alloys is presented. The equilibrium solid solubility of carbon in -iron is calculated for given grain size. Inside the strained nanograins local variation of the carbon content is predicted. Due to the nonlinear relation between strain and solubility, the averaged solubility in the grain interior increases with decreasing grain size. The majority of the global solubility enhancement is due to grain boundary enrichment however. Therefor...

Diagnosing solubility limitations – the example of hydrate formation

Directory of Open Access Journals (Sweden)

Joerg Berghausen

2014-07-01

Full Text Available Solubility is regarded as one of the key challenges in many drug discovery projects. Thus, it’s essential to support the lead finding and optimization efforts by appropriate solubility data. In silico solubility prediction remains challenging and therefore a screening assay is used as a first filter, followed by selected follow-up assays to reveal what causes the low solubility of a specific compound or chemotype. Results from diagnosing the underlying reason for solubility limitation are discussed. As lipophilicity and crystal lattice forces are regarded as main contributors to limiting solubility, changes in solid state are important to be recognized. Solubility limitation by various factors will be presented and the impact of the solid-state is exemplified by compounds that are able to form hydrates.

Molecular dynamics study of salt–solution interface: Solubility and surface charge of salt in water

International Nuclear Information System (INIS)

Kobayashi, Kazuya; Liang, Yunfeng; Matsuoka, Toshifumi; Sakka, Tetsuo

2014-01-01

The NaCl salt–solution interface often serves as an example of an uncharged surface. However, recent laser-Doppler electrophoresis has shown some evidence that the NaCl crystal is positively charged in its saturated solution. Using molecular dynamics (MD) simulations, we have investigated the NaCl salt–solution interface system, and calculated the solubility of the salt using the direct method and free energy calculations, which are kinetic and thermodynamic approaches, respectively. The direct method calculation uses a salt–solution combined system. When the system is equilibrated, the concentration in the solution area is the solubility. In the free energy calculation, we separately calculate the chemical potential of NaCl in two systems, the solid and the solution, using thermodynamic integration with MD simulations. When the chemical potential of NaCl in the solution phase is equal to the chemical potential of the solid phase, the concentration of the solution system is the solubility. The advantage of using two different methods is that the computational methods can be mutually verified. We found that a relatively good estimate of the solubility of the system can be obtained through comparison of the two methods. Furthermore, we found using microsecond time-scale MD simulations that the positively charged NaCl surface was induced by a combination of a sodium-rich surface and the orientation of the interfacial water molecules

Potable NIR spectroscopy predicting soluble solids content of pears based on LEDs

Energy Technology Data Exchange (ETDEWEB)

Liu Yande; Liu Wei; Sun Xudong; Gao Rongjie; Pan Yuanyuan; Ouyang Aiguo, E-mail: jxliuyd@163.com [School of Mechatronics Engineering, East China Jiaotong University, Changbei Open and Developing District, Nanchang, 330013 (China)

2011-01-01

A portable near-infrared (NIR) instrument was developed for predicting soluble solids content (SSC) of pears equipped with light emitting diodes (LEDs). NIR spectra were collected on the calibration and prediction sets (145:45). Relationships between spectra and SSC were developed by multivariate linear regression (MLR), partial least squares (PLS) and artificial neural networks (ANNs) in the calibration set. The 45 unknown pears were applied to evaluate the performance of them in terms of root mean square errors of prediction (RMSEP) and correlation coefficients (r). The best result was obtained by PLS with RMSEP of 0.62{sup 0}Brix and r of 0.82. The results showed that the SSC of pears could be predicted by the portable NIR instrument.

Potable NIR spectroscopy predicting soluble solids content of pears based on LEDs

International Nuclear Information System (INIS)

Liu Yande; Liu Wei; Sun Xudong; Gao Rongjie; Pan Yuanyuan; Ouyang Aiguo

2011-01-01

A portable near-infrared (NIR) instrument was developed for predicting soluble solids content (SSC) of pears equipped with light emitting diodes (LEDs). NIR spectra were collected on the calibration and prediction sets (145:45). Relationships between spectra and SSC were developed by multivariate linear regression (MLR), partial least squares (PLS) and artificial neural networks (ANNs) in the calibration set. The 45 unknown pears were applied to evaluate the performance of them in terms of root mean square errors of prediction (RMSEP) and correlation coefficients (r). The best result was obtained by PLS with RMSEP of 0.62 0 Brix and r of 0.82. The results showed that the SSC of pears could be predicted by the portable NIR instrument.

Novel electrosprayed nanospherules for enhanced aqueous solubility and oral bioavailability of poorly water-soluble fenofibrate.

Science.gov (United States)

Yousaf, Abid Mehmood; Mustapha, Omer; Kim, Dong Wuk; Kim, Dong Shik; Kim, Kyeong Soo; Jin, Sung Giu; Yong, Chul Soon; Youn, Yu Seok; Oh, Yu-Kyoung; Kim, Jong Oh; Choi, Han-Gon

2016-01-01

The purpose of the present research was to develop a novel electrosprayed nanospherule providing the most optimized aqueous solubility and oral bioavailability for poorly water-soluble fenofibrate. Numerous fenofibrate-loaded electrosprayed nanospherules were prepared with polyvinylpyrrolidone (PVP) and Labrafil(®) M 2125 as carriers using the electrospray technique, and the effect of the carriers on drug solubility and solvation was assessed. The solid state characterization of an optimized formulation was conducted by scanning electron microscopy, powder X-ray diffraction, differential scanning calorimetry, and Fourier transform infrared spectroscopic analyses. Oral bioavailability in rats was also evaluated for the formulation of an optimized nanospherule in comparison with free drug and a conventional fenofibrate-loaded solid dispersion. All of the electrosprayed nanospherule formulations had remarkably enhanced aqueous solubility and dissolution compared with free drug. Moreover, Labrafil M 2125, a surfactant, had a positive influence on the solubility and dissolution of the drug in the electrosprayed nanospherule. Increases were observed as the PVP/drug ratio increased to 4:1, but higher ratios gave no significant increases. In particular, an electrosprayed nanospherule composed of fenofibrate, PVP, and Labrafil M 2125 at the weight ratio of 1:4:0.5 resulted in a particle size of water-soluble fenofibrate.

WATEQ3 geochemical model: thermodynamic data for several additional solids

International Nuclear Information System (INIS)

Krupka, K.M.; Jenne, E.A.

1982-09-01

Geochemical models such as WATEQ3 can be used to model the concentrations of water-soluble pollutants that may result from the disposal of nuclear waste and retorted oil shale. However, for a model to competently deal with these water-soluble pollutants, an adequate thermodynamic data base must be provided that includes elements identified as important in modeling these pollutants. To this end, several minerals and related solid phases were identified that were absent from the thermodynamic data base of WATEQ3. In this study, the thermodynamic data for the identified solids were compiled and selected from several published tabulations of thermodynamic data. For these solids, an accepted Gibbs free energy of formation, ΔG 0 /sub f,298/, was selected for each solid phase based on the recentness of the tabulated data and on considerations of internal consistency with respect to both the published tabulations and the existing data in WATEQ3. For those solids not included in these published tabulations, Gibbs free energies of formation were calculated from published solubility data (e.g., lepidocrocite), or were estimated (e.g., nontronite) using a free-energy summation method described by Mattigod and Sposito (1978). The accepted or estimated free energies were then combined with internally consistent, ancillary thermodynamic data to calculate equilibrium constants for the hydrolysis reactions of these minerals and related solid phases. Including these values in the WATEQ3 data base increased the competency of this geochemical model in applications associated with the disposal of nuclear waste and retorted oil shale. Additional minerals and related solid phases that need to be added to the solubility submodel will be identified as modeling applications continue in these two programs

Equilibrium solubility of CO{sub 2} in aqueous solutions of 1-amino-2-propanol as function of concentration, temperature, and pressure

Energy Technology Data Exchange (ETDEWEB)

Rebolledo-Morales, Miguel Angel; Rebolledo-Libreros, Maria Esther [Instituto Mexicano del Petroleo, Direccion de Investigacion y Posgrado, Programa de Ingenieria Molecular, Area de Investigacion de Termofisica, Eje Central Lazaro Cardenas Norte 152, 07730 Mexico, D.F. (Mexico); Trejo, Arturo, E-mail: atrejo@imp.m [Instituto Mexicano del Petroleo, Direccion de Investigacion y Posgrado, Programa de Ingenieria Molecular, Area de Investigacion de Termofisica, Eje Central Lazaro Cardenas Norte 152, 07730 Mexico, D.F. (Mexico)

2011-05-15

Research highlights: Gas solubility of CO{sub 2} in aqueous solutions of 1-amino-2-propanol was measured. Solubility increases as pressure and concentration of 1-amino-2-propanol increase. The Kent-Eisenberg model was used to correlate all the experimental results. Aqueous solutions of MIPA are an excellent alternative to use in gas purification. - Abstract: Using a dynamic method with recirculation of the vapour phase, experimental values for the gas solubility of carbon dioxide in aqueous solutions of 1-amino-2-propanol (MIPA) were measured at T = (313.15 and 393.15) K, over the pressure range of (0.2 to 2436.4) kPa. The concentrations of the studied aqueous MIPA solutions were (0.20, 0.30, 0.40, and 0.50) mass fraction. The results of gas solubility are given as the partial pressure of CO{sub 2}, p{sub CO{sub 2}}, against its mole ratio, {alpha}{sub CO{sub 2}} (mol CO{sub 2} {center_dot} mol{sup -1} MIPA), and its mole fraction, x{sub CO{sub 2}}. It is observed that the solubility of CO{sub 2} increases as the concentration of MIPA in solution increases, at a given temperature throughout the pressure range considered; also the solubility values increase, under constant temperature, as the pressure increases in the studied concentration range of MIPA. The physicochemical model of Kent and Eisenberg was used to correlate simultaneously all the experimental results of the solubility of CO{sub 2} in the studied aqueous solutions of MIPA. The model correlates satisfactorily the experimental results. The deviation for pressure was 96.9 kPa using 62 experimental solubility points. The solubility results of carbon dioxide presented in this work are compared with those reported in the literature for aqueous solutions of monoethanolamine (MEA), diethanolamine (DEA), diisopropanolamine (DIPA), and N-methyldiethanolamine (MDEA) and it is possible to conclude that the aqueous solutions of MIPA are an excellent alternative to use in gas purification processes, since the

Characterization of CurcuEmulsomes: nanoformulation for enhanced solubility and delivery of curcumin

Science.gov (United States)

2013-01-01

Background Curcumin is a polyphenolic compound isolated from the rhizomes of the plant Curcuma longa and shows intrinsic anti-cancer properties. Its medical use remains limited due to its extremely low water solubility and bioavailability. Addressing this problem, drug delivery systems accompanied by nanoparticle technology have emerged. The present study introduces a novel nanocarrier system, so-called CurcuEmulsomes, where curcumin is encapsulated inside the solid core of emulsomes. Results CurcuEmulsomes are spherical solid nanoparticles with an average size of 286 nm and a zeta potential of 37 mV. Encapsulation increases the bioavailability of curcumin by up to 10,000 fold corresponding to a concentration of 0.11 mg/mL. Uptaken by HepG2 human liver carcinoma cell line, CurcuEmulsomes show a significantly prolonged biological activity and demonstrated therapeutic efficacy comparable to free curcumin against HepG2 in vitro - with a delay in response, as assessed by cell viability, apoptosis and cell cycle studies. The delay is attributed to the solid character of the nanocarrier prolonging the release of curcumin inside the HepG2 cells. Conclusions Incorporation of curcumin into emulsomes results in water-soluble and stable CurcuEmulsome nanoformulations. CurcuEmulsomes do not only successfully facilitate the delivery of curcumin into the cell in vitro, but also enable curcumin to reach its effective concentrations inside the cell. The enhanced solubility of curcumin and the promising in vitro efficacy of CurcuEmulsomes highlight the potential of the system for the delivery of lipophilic drugs. Moreover, high degree of compatibility, prolonged release profile and tailoring properties feature CurcuEmulsomes for further therapeutic applications in vivo. PMID:24314310

Characterization of CurcuEmulsomes: nanoformulation for enhanced solubility and delivery of curcumin.

Science.gov (United States)

Ucisik, Mehmet H; Küpcü, Seta; Schuster, Bernhard; Sleytr, Uwe B

2013-12-06

Curcumin is a polyphenolic compound isolated from the rhizomes of the plant Curcuma longa and shows intrinsic anti-cancer properties. Its medical use remains limited due to its extremely low water solubility and bioavailability. Addressing this problem, drug delivery systems accompanied by nanoparticle technology have emerged. The present study introduces a novel nanocarrier system, so-called CurcuEmulsomes, where curcumin is encapsulated inside the solid core of emulsomes. CurcuEmulsomes are spherical solid nanoparticles with an average size of 286 nm and a zeta potential of 37 mV. Encapsulation increases the bioavailability of curcumin by up to 10,000 fold corresponding to a concentration of 0.11 mg/mL. Uptaken by HepG2 human liver carcinoma cell line, CurcuEmulsomes show a significantly prolonged biological activity and demonstrated therapeutic efficacy comparable to free curcumin against HepG2 in vitro - with a delay in response, as assessed by cell viability, apoptosis and cell cycle studies. The delay is attributed to the solid character of the nanocarrier prolonging the release of curcumin inside the HepG2 cells. Incorporation of curcumin into emulsomes results in water-soluble and stable CurcuEmulsome nanoformulations. CurcuEmulsomes do not only successfully facilitate the delivery of curcumin into the cell in vitro, but also enable curcumin to reach its effective concentrations inside the cell. The enhanced solubility of curcumin and the promising in vitro efficacy of CurcuEmulsomes highlight the potential of the system for the delivery of lipophilic drugs. Moreover, high degree of compatibility, prolonged release profile and tailoring properties feature CurcuEmulsomes for further therapeutic applications in vivo.

KRISTALLIN-I: estimates of solubility limits for safety relevant radionuclides

International Nuclear Information System (INIS)

Berner, U.

1995-04-01

The safety concept for the Swiss high level radioactive waste repository is based on a multiple barrier system. Within the concept of the safety analysis KRISTALLIN-I, the waste glass starts corroding after failure of the massive steel canister and nuclides are released to the bentonite backfill. This release is limited by restricted solubility of solid phases. The present work quantifies the maximum expected concentrations of the elements Th, Pa, U, Np, Pu, Am, Cm, Tc, Ni, Pd, Se, Ra, Zr, Nb, Sn, Pb, Sb, Bi and Sm within the reference bentonite porewater with pH = 9, Eh = -400 mV and I = 0.08 M at 50 o C. In a first step, maximum expected concentrations were calculated with a geochemical speciation code (MINEQL) based on a documented thermodynamic database. In a second step, the values obtained in this way were carefully reviewed and modified, based on extended geochemical considerations and system-dependent parameters. Thereby, the relevance of potentially limiting solids, chemical analogies, absolute and relative inventories and recent experimental findings from laboratory and natural systems were particularly considered. The expected groundwater composition in the crystalline host rock (modified by the barrier material bentonite) covers a rather narrow pH range from 8.5 to 9. Within this narrow pH range, solubility limits may be termed as pH independent since computable pH effects are never significant compared to the general uncertainty of the solubility limits. The chemical model defining the reference groundwater predicts a system-wide Eh ranging from -400 mV up to +100 mV. A slightly oxidising near-field will stabilize the generally more soluble higher oxidation states of redox sensitive radionuclides. Based on the available thermodynamic data the elements U, Tc, Se and Pa are predicted not to be solubility limited at +75 mV. Therefore, a more detailed investigation of the redox behaviour of critical elements and, much more importantly, a very careful

Kinetics of the isothermal decomposition of zirconium hydride: terminal solid solubility for precipitation and dissolution

Science.gov (United States)

Denisov, E. A.; Kompaniets, T. N.; Voyt, A. P.

2018-05-01

The hydrogen permeation technique in the surface-limited regime (SLR) was first used to study the isothermal decomposition of zirconium hydride. It is shown that under isothermal conditions, the hydrogen terminal solid solubility in the α-phase for hydride precipitation (TSSp) and dissolution (TSSd) differ only by 6%, in contrast to the 20-30% indicated in the available literature. It is demonstrated that even the minimum heating/cooling rate (1 C/min) used in the traditional methods of studying TSSp and TSSd is too high to exclude the effect of kinetics on the results obtained.

Mechanical properties, phenolic composition and extractability indices of Barbera grapes of different soluble solids contents from several growing areas.

Science.gov (United States)

Torchio, Fabrizio; Cagnasso, Enzo; Gerbi, Vincenzo; Rolle, Luca

2010-02-15

Phenolic compounds, extractable from grape skins and seeds, have a notable influence on the quality of red wines. Many studies have clearly demonstrated the relationship between the phenolic composition of the grape at harvest time and its influence on the phenolic composition of the red wine produced. In many previous works the evolution of phenolic composition and relative extractability was normally studied on grapes sampled at different times during ripening, but at the same date the physiological characteristics of grape berries in a vineyard are often very heterogeneous. Therefore, the main goal of the study is to investigate the differences among mechanical properties, phenolic composition and relative extractability of Vitis vinifera L. cv Barbera grape berries, harvested at the same date from several vineyards, and calibrated according to their density at three levels of soluble solids (A=235+/-8, B=252+/-8 and C=269+/-8 g L(-1) sugar) with the aim of studying the influence of ripeness stages and growing locations on these parameters. Results on mechanical properties showed that the thickness of the berry skin (Sp(sk)) was the parameter most affected by the different level of sugars in the pulp, while different skin hardnesses, evaluated by the break skin force (F(sk)), were related to the cultivation sites. The latter were also observed to influence the mechanical characteristics of seeds. Generally, the anthocyanin content increased with the level of soluble solids, while the increase in the tannin content of the berry skin and seeds was less marked. However, significant changes in flavanols reactive to vanillin in the seeds were found. The cellular maturity index (EA%) was little influenced by the soluble solids content of grapes. Copyright 2009 Elsevier B.V. All rights reserved.

Development of an irrigation control device based on solar radiation and its adaptability for cultivation of high soluble solid tomato fruit in root zone restriction culture

International Nuclear Information System (INIS)

Nitta, M.; Shibuya, K.; Kubai, K.; Komatsu, H.; Hosokawa, T.; Nakamura, K.

2009-01-01

An irrigation control device based on solar radiation was developed to allow automatic irrigation management for high soluble solid tomato fruit production in root zone restriction culture. Its adaptability for long-term cultivation (planting carried out in early September and harvesting ending in late June) of high soluble solid tomato fruit in root zone restriction culture was examined. The following results were obtained: 1. The control device was composed of generally available electronic parts. A change of setting was possible for the irrigation starting point, the irrigation time period, and the once amount of irrigation. For the first irrigation of the day, one of two irrigation control modes can be chosen; the first determines irrigation dependent on the solar radiation after the irrigated time of the previous day. The second mode irrigates at a set time. 2. The correlation between the total integrated solar radiation and the evapotranspiration rate of tomato plants were investigated. Positive correlations were observed for each month from October to June. Moreover, total integrated solar radiation per unit evapotranspiration was different for each month. 3. In long-term cultivation of tomato fruit using this device, the marketable yield of high soluble solid tomato fruit (more than Brix 8%) was 9.7t/10a. 4. This device exhibited the necessary adaptability for use in long-term cultivation of high soluble solid tomato fruit in root zone restriction culture, by changing the set value of the irrigation starting point and the irrigation time period in accordance with the growth period

The solubilities and solubility products of zirconium hydroxide and oxide after aging at 278, 313, and 333 K

Energy Technology Data Exchange (ETDEWEB)

Kobayashi, Taishi; Uemura, Takuya; Sasaki, Takayuki; Takagi, Ikuji [Kyoto Univ. (Japan). Dept. of Nuclear Engineering; Moriyama, Hirotake [Kyoto Univ. (Japan). Research Reactor Inst.

2016-07-01

The solubilities of zirconium hydroxide and oxide after aging at 278, 313, and 333 K were measured at 278, 298, 313, and 333 K in the pH{sub c} range of 0.3-7 in a 0.5 M ionic strength solution of NaClO{sub 4} and HClO{sub 4}. Size distributions of the colloidal species were investigated by ultrafiltration using membranes with different pore sizes, and the solid phases were examined by X-ray diffraction. The apparent solubility of zirconium amorphous hydroxide (Zr(OH){sub 4}(am)), prepared by the oversaturation method, decreased with increasing aging temperature (T{sub a}), and the size distributions obtained after aging at elevated temperatures indicated the growth of the colloidal species. We, therefore, suggested that agglomeration of the colloidal species and dehydration and crystallization of Zr(OH){sub 4}(am) as the solubility-limiting solid phase occurred over the course of aging at elevated temperatures. For sample solutions of the crystalline oxide (ZrO{sub 2}(cr)), the aging temperature had no significant effect on the solubility, but the solubility data at lower temperatures were found to be slightly higher than those at higher temperatures, implying a small fraction of the amorphous components. In the analysis of different solid phases (Zr(OH){sub 4}(s,T{sub a}), T{sub a} = 278, 313, and 333 K) depending on the aging temperatures, the solubility products (K{sub sp}, T{sub a}) were determined at different measurement temperatures, and the enthalpy change (Δ{sub r}H {sup circle}) for Zr{sup 4+} 4OH{sup -} <=> Zr(OH){sub 4}(s,T{sub a}) was calculated using the van't Hoff equation. The solid-phase-transformation process at elevated temperatures was also analyzed based on the obtained K{sub sp}, T{sub a} and Δ{sub r}H {sup circle} values.

Determining a Solubility Product Constant by Potentiometric Titration to Increase Students' Conceptual Understanding of Potentiometry and Titrations

Science.gov (United States)

Grabowski, Lauren E.; Goode, Scott R.

2017-01-01

Potentiometric titrations are widely taught in first-year undergraduate courses to connect electrochemistry, stoichiometry, and equilibria and to reinforce acid-base titrations. Students perform a potentiometric titration that is then analyzed to determine analyte concentrations and the solubility product constant of the solid species.

Synthesis of new water-soluble metal-binding polymers: Combinatorial chemistry approach. 1997 mid-year progress report

International Nuclear Information System (INIS)

Smith, B.F.

1997-01-01

'The first objective of this research is to develop rapid discovery and optimization approaches to new water-soluble chelating polymers. A byproduct of the development approach will be the new, selective, and efficient metal-binding agents. The second objective is to evaluate the concept of using water and organic soluble polymers as new solid supports for combinatorial synthesis. The technology under development, Polymer Filtration (PF), is a technique to selectively remove or recover hazardous and valuable metal ions and radionuclides from various dilute aqueous streams. Not only can this technology be used to remediate contaminated soils and solid surfaces and treat aqueous wastes, it can also be incorporated into facilities as a pollution prevention and waste minimization technology. Polymer Filtration uses water-soluble metal-binding polymers to sequester metal ions in dilute solution. The water-soluble polymers have a sufficiently large molecular size that they can be separated and concentrated using commercial ultrafiltration technology. Water, small organic molecules, and unbound metals pass freely through the ultrafiltration membrane while concentrating the metal-binding polymer. The polymers can then be reused by changing the solution conditions to release the metal ions. The metal-ions are recovered in concentrated form for recycle or disposal using a diafiltration process. The water-soluble polymer can be recycled for further aqueous-stream processing. To advance Polymer Filtration technology to the selectivity levels required for DOE needs. fixture directions in Polymer Filtration must include rapid development, testing, and characterization of new metal-binding polymers. The development of new chelating molecules can be equated to the process of new drugs or new materials discovery. Thus, the authors want to build upon and adapt the combinatorial chemistry approaches developed for rapid molecule generation for the drug industry to the rapid

On the americium oxalate solubility

International Nuclear Information System (INIS)

Zakolupin, S.A.; Korablin, Eh.V.

1977-01-01

The americium oxalate solubility at different nitric (0.0-1 M) and oxalic (0.0-0.4 M) acid concentrations was investigated in the temperature range from 14 to 60 deg C. The dependence of americium oxalate solubility on the oxalic acid concentration was determined. Increasing oxalic acid concentration was found to reduce the americium oxalate solubility. The dependence of americium oxalate solubility on the oxalic acid concentration was noted to be a minimum at low acidity (0.1-0.3 M nitric acid). This is most likely due to Am(C 2 O 4 ) + , Am(C 2 O 4 ) 2 - and Am(C 2 O 4 ) 3 3- complex ion formation which have different unstability constants. On the basis of the data obtained, a preliminary estimate was carried out for the product of americium oxalate solubility in nitric acid medium (10 -29 -10 -31 ) and of the one in water (6.4x10 -20 )

Effect of solids concentration on removal of heavy metals from mine tailings via bioleaching

International Nuclear Information System (INIS)

Liu Yunguo; Zhou Ming; Zeng Guangming; Li Xin; Xu Weihua; Fan Ting

2007-01-01

Mining of mineral ore and disposal of resulting waste tailings pose a significant risk to the surrounding environment. The objective of this work is to demonstrate the feasibility to remove heavy metals from mine tailings with the use of bioleaching and meanwhile to investigate the effect of solids concentration on removal of heavy metals from mine tailings by indigenous sulfur-oxidizing bacteria and the transformation of heavy metal forms after the bioleaching process. This work showed the laboratory results of bioleaching experiments on Pb-Zn-Cu mine tailings. The results showed that 98.08% Zn, 96.44% Cu, and 43.52% Pb could be removed from mine tailings by the bioleaching experiment after 13 days at 1% (w/v) solids concentration and the rates of pH reduction, ORP rise and sulfate production were reduced with the increase of solids concentration, due to the buffering capacity of mine tailing solids. The results also indicated that solid concentration 1% was found to be best to bacterial activity and metal solubilization of the five solids concentration tested (1%, 2%, 5%, 8% and 10%) under the chosen experimental conditions. In addition, the bioleaching had a significant impact on changes in partitioning of heavy metals

Effect of solids concentration on removal of heavy metals from mine tailings via bioleaching

Energy Technology Data Exchange (ETDEWEB)

Liu Yunguo [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China)]. E-mail: axore@163.com; Zhou Ming [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Zeng Guangming [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Li Xin [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Xu Weihua [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Fan Ting [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China)

2007-03-06

Mining of mineral ore and disposal of resulting waste tailings pose a significant risk to the surrounding environment. The objective of this work is to demonstrate the feasibility to remove heavy metals from mine tailings with the use of bioleaching and meanwhile to investigate the effect of solids concentration on removal of heavy metals from mine tailings by indigenous sulfur-oxidizing bacteria and the transformation of heavy metal forms after the bioleaching process. This work showed the laboratory results of bioleaching experiments on Pb-Zn-Cu mine tailings. The results showed that 98.08% Zn, 96.44% Cu, and 43.52% Pb could be removed from mine tailings by the bioleaching experiment after 13 days at 1% (w/v) solids concentration and the rates of pH reduction, ORP rise and sulfate production were reduced with the increase of solids concentration, due to the buffering capacity of mine tailing solids. The results also indicated that solid concentration 1% was found to be best to bacterial activity and metal solubilization of the five solids concentration tested (1%, 2%, 5%, 8% and 10%) under the chosen experimental conditions. In addition, the bioleaching had a significant impact on changes in partitioning of heavy metals.

Effect of water soluble carrier on dissolution profiles of diclofenac sodium.

Science.gov (United States)

Cwiertnia, Barbara

2013-01-01

Pharmaceutical aviailability of diclofenac sodium from solid dispersions of PEG 6000 have been studied in comparison to those of the corresponding physical mixtures and pure diclofenac sodium. The diclofenac sodium is poorly water soluble drug. The properties of diclofenac sodium-PEG 6000 solid dispersions have been determined by the methods of differential scanning calorimetry (DSC), X-ray diffraction and scanning electron microscopy (SEM). The effect of PEG 6000 on the solubility of selected diclofenac sodium dispersions has been studied. The solubility of diclofenac sodium from its solid dispersion has been found to increase in the presence of PEG 6000.

Increased serum concentrations of soluble ST2 predict mortality after burn injury.

Science.gov (United States)

Hacker, Stefan; Dieplinger, Benjamin; Werba, Gregor; Nickl, Stefanie; Roth, Georg A; Krenn, Claus G; Mueller, Thomas; Ankersmit, Hendrik J; Haider, Thomas

2018-06-27

Large burn injuries induce a systemic response in affected patients. Soluble ST2 (sST2) acts as a decoy receptor for interleukin-33 (IL-33) and has immunosuppressive effects. sST2 has been described previously as a prognostic serum marker. Our aim was to evaluate serum concentrations of sST2 and IL-33 after thermal injury and elucidate whether sST2 is associated with mortality in these patients. We included 32 burn patients (total body surface area [TBSA] >10%) admitted to our burn intensive care unit and compared them to eight healthy probands. Serum concentrations of sST2 and IL-33 were measured serially using an enzyme-linked immunosorbent assay (ELISA) technique. The mean TBSA was 32.5%±19.6%. Six patients (18.8%) died during the hospital stay. Serum analyses showed significantly increased concentrations of sST2 and reduced concentrations of IL-33 in burn patients compared to healthy controls. In our study cohort, higher serum concentrations of sST2 were a strong independent predictor of mortality. Burn injuries cause an increment of sST2 serum concentrations with a concomitant reduction of IL-33. Higher concentrations of sST2 are associated with increased in-hospital mortality in burn patients.

Understanding the role of lithium polysulfide solubility in limiting lithium-sulfur cell capacity

International Nuclear Information System (INIS)

Shen, Chao; Xie, Jianxin; Zhang, Mei; Andrei, Petru; Hendrickson, Mary; Plichta, Edward J.; Zheng, Jim P.

2017-01-01

Highlights: •At normal rate, LiPS soluble reaction pathway dominates the discharge process. •Reduction of sulfur to Li 2 S 8 is not inhibited by high Li 2 S 8 concentration. •Subsequent LiPS electrochemical reactions are restricted by LiPS solubility. •Specific energy of the Li-S cell was reevaluated considering LiPS solubility. -- Abstract: Although the cathode of lithium-sulfur (Li-S) batteries has a theoretical specific capacity of 1,672 mAh g −1 , its practical capacity is much smaller than this value and depends on the electrolyte/sulfur ratio. The operation of Li-S batteries under lean electrolyte conditions can be challenging, especially in the case when the solubility of lithium polysulfide (LiPS) sets an upper bound for polysulfide dissolution. In this work, specially designed cathode structures and electrolyte configurations were built in order to analyze the effects of LiPS solubility on cell capacity. Two reaction pathways involving the reduction of LiPS in liquid and solid phase are proposed and analyzed. We show that at discharge rates above 0.4 mA cm −2 the reaction in the liquid phase dominates the discharge process. Once the electrolyte becomes saturated, the solid phase LiPS cannot be further reduced and does not contribute to the capacity of the cells. This phenomenon prevents Li-S batteries from achieving their high theoretical specific capacity. Finally, the specific energy of the Li-S cell is reevaluated and discussed considering the limitation imposed by LiPS solubility.

Controlled release systems containing solid dispersions: strategies and mechanisms.

Science.gov (United States)

Tran, Phuong Ha-Lien; Tran, Thao Truong-Dinh; Park, Jun Bom; Lee, Beom-Jin

2011-10-01

In addition to a number of highly soluble drugs, most new chemical entities under development are poorly water-soluble drugs generally characterized by an insufficient dissolution rate and a small absorption window, leading to the low bioavailability. Controlled-release (CR) formulations have several potential advantages over conventional dosage forms, such as providing a uniform and prolonged therapeutic effect to improve patient compliance, reducing the frequency of dosing, minimizing the number of side effects, and reducing the strength of the required dose while increasing the effectiveness of the drug. Solid dispersions (SD) can be used to enhance the dissolution rate of poorly water-soluble drugs and to sustain the drug release by choosing an appropriate carrier. Thus, a CR-SD comprises both functions of SD and CR for poorly water-soluble drugs. Such CR dosage forms containing SD provide an immediately available dose for an immediate action followed by a gradual and continuous release of subsequent doses to maintain the plasma concentration of poorly water-soluble drugs over an extended period of time. This review aims to summarize all currently known aspects of controlled release systems containing solid dispersions, focusing on the preparation methods, mechanisms of action and characterization of physicochemical properties of the system.

Advantageous Solubility-Permeability Interplay When Using Amorphous Solid Dispersion (ASD) Formulation for the BCS Class IV P-gp Substrate Rifaximin: Simultaneous Increase of Both the Solubility and the Permeability.

Science.gov (United States)

Beig, Avital; Fine-Shamir, Noa; Lindley, David; Miller, Jonathan M; Dahan, Arik

2017-05-01

Rifaximin is a BCS class IV (low-solubility, low-permeability) drug and also a P-gp substrate. The aims of this work were to assess the efficiency of different rifaximin amorphous solid dispersion (ASDs) formulations in achieving and maintaining supersaturation and to investigate the consequent solubility-permeability interplay. Spray-dried rifaximin ASDs were prepared with different hydrophilic polymers and their ability to achieve and maintain supersaturation was assessed. Then, rifaximin's apparent intestinal permeability was investigated as a function of increasing supersaturation both in vitro using the parallel artificial membrane permeability assay (PAMPA) and in vivo using the single-pass rat intestinal perfusion (SPIP) model. The efficiency of the different ASDs to achieve and maintain supersaturation of rifaximin was found to be highly polymer dependent, and the copovidone/HPC-SL formulation was found to be superior to the other two, allowing supersaturation of 200× that of the crystalline solubility for 20 h. In vitro, rifaximin flux was increased and the apparent permeability was constant as a function of increasing supersaturation level. In vivo, on the other hand, absorption rate coefficient (k a ) was first constant as a function of increasing supersaturation, but at 250×, the crystalline solubility k a was doubled, similar to the k a in the presence of the strong P-gp inhibitor GF120918. In conclusion, a new and favorable nature of solubility-permeability interplay was revealed in this work: delivering high supersaturation level of the BCS class IV drug rifaximin via ASD, thereby saturating the drugs' P-gp-mediated efflux transport, led to the favorable unique win-win situation, where both the solubility and the permeability increased simultaneously.

Bench-Scale and Pilot-Scale Treatment Technologies for the Removal of Total Dissolved Solids from Coal Mine Water: A Review

Science.gov (United States)

Coal mine water (CMW) is typically treated to remove suspended solids, acidity, and soluble metals, but high concentrations of total dissolved solids (TDS) have been reported to impact the environment at several CMW discharge points. Consequently, various states have establishe...

Alcohol dose dumping: The influence of ethanol on hot-melt extruded pellets comprising solid lipids.

Science.gov (United States)

Jedinger, N; Schrank, S; Mohr, S; Feichtinger, A; Khinast, J; Roblegg, E

2015-05-01

The objective of the present study was to investigate interactions between alcohol and hot-melt extruded pellets and the resulting drug release behavior. The pellets were composed of vegetable calcium stearate as matrix carrier and paracetamol or codeine phosphate as model drugs. Two solid lipids (Compritol® and Precirol®) were incorporated into the matrix to form robust/compact pellets. The drug release characteristics were a strong function of the API solubility, the addition of solid lipids, the dissolution media composition (i.e., alcohol concentration) and correspondingly, the pellet wettability. Pellets comprising paracetamol, which is highly soluble in ethanol, showed alcohol dose dumping regardless of the matrix composition. The wettability increased with increasing ethanol concentrations due to higher paracetamol solubilities yielding increased dissolution rates. For pellets containing codeine phosphate, which has a lower solubility in ethanol than in acidic media, the wettability was a function of the matrix composition. Dose dumping occurred for formulations comprising solid lipids as they showed increased wettabilities with increasing ethanol concentrations. In contrast, pellets comprising calcium stearate as single matrix component showed robustness in alcoholic media due to wettabilities that were not affected by the addition of ethanol. The results clearly indicate that the physico-chemical properties of the drug and the matrix systems are crucial for the design of ethanol-resistant dosage forms. Moreover, hydrophobic calcium stearate can be considered a suitable matrix system that minimizes the risk of ethanol-induced dose dumping for certain API's. Copyright © 2015 Elsevier B.V. All rights reserved.

Daily rhythm of circulating fat soluble vitamin concentration (A, D, E and K in the horse

Directory of Open Access Journals (Sweden)

Caola Giovanni

2004-07-01

Full Text Available Abstract Background Many physiological processes of mammalian species exhibit daily rhythmicity. An intrinsic relationship exists between fat soluble vitamins (A, D, E and K and several body functions. Few investigations on the rhythmic pattern of vitamins in domestic animals have been carried out. The present study evaluated the circadian rhythmicity of fat soluble vitamins in the horse. Methods Blood samples from 5 Thoroughbred mares were collected at four-hour intervals over a 48-hour period (starting at 8:00 hours on day 1 and finishing at 4:00 on day 2 via an intravenous cannula inserted into the jugular vein. Fat soluble vitamin concentration in the serum (A, D, E and K was measured by HPLC. One-way repeated measures analysis of variance (ANOVA was used to determine significant differences. p values Results ANOVA showed a highly significant effect of time in all the horses for the vitamins studied (p Conclusion Fat soluble vitamins exhibit daily rhythmicity with diurnal peak. Further investigations could help optimize the use of these substances according to their circadian (or other rhythms.

Differences in fluorescence characteristics and bioavailability of water-soluble organic matter (WSOM) in sediments and suspended solids in Lihu Lake, China.

Science.gov (United States)

Wang, Wenwen; Wang, Shuhang; Jiang, Xia; Zheng, Binghui; Zhao, Li; Zhang, Bo; Chen, Junyi

2018-05-01

The spectral characteristics, spatial distribution, and bioavailability of water-soluble organic matter (WSOM) in suspended solids and surface sediments of Lihu Lake, China, were investigated through excitation-emission matrix spectra and parallel factor analysis. The average content of dissolved organic carbon (DOC) in the sediments reached 643.28 ± 58.34 mg C/kg and that in suspended solids was 714.87 ± 69.24 mg C/kg. The fluorescence intensity of WSOM totaled 90.87 ± 5.65 and 115.42 ± 8.02 RU/g for the sediments and suspended solids, respectively. The DOC and fluorescence intensity of the WSOM showed an increasing trend moving from the west to the east of the lake. The WSOM in sediments and suspended solids contained two humic-like (C1 and C2) and one tryptophan-like (C3) components. These components had different fluorescent peaks and relative proportions. In the sediments, the relative proportions of C1, C2, and C3 were 33.71% ± 0.71, 26.83% ± 0.68, and 39.50% ± 0.71%, respectively. Meanwhile, C1 (35.77 ± 0.84%), C2 (34.07 ± 0.61%), and C3 (30.16 ± 0.75%) had similar relative percentages in suspended solids. The sediments had a lower humification index (3.02 ± 0.08) than the suspended solids (4.04 ± 0.15). Exchangeable nitrogen for the sediments and suspended solids was dominated by exchangeable ammonium nitrogen and soluble organic nitrogen, respectively. WSOM plays an important role in migration and transformation of nitrogen in sediments and suspended solids. The sediment-derived WSOM exhibited higher lability and biological activity than did the suspended solid-derived WSOM. The relative ratio of the intensity of protein-like fluorescent component to that of the humic-like one can be used as a reference index to evaluate the lability and biological activity of WSOM in sediments and suspended solids.

Seasonal changes in Fe species and soluble Fe concentration in the atmosphere in the Northwest Pacific region based on the analysis of aerosols collected in Tsukuba, Japan

Directory of Open Access Journals (Sweden)

Y. Takahashi

2013-08-01

Full Text Available Atmospheric iron (Fe can be a significant source of nutrition for phytoplankton inhabiting remote oceans, which in turn has a large influence on the Earth's climate. The bioavailability of Fe in aerosols depends mainly on the fraction of soluble Fe (= [FeSol]/[FeTotal], where [FeSol] and [FeTotal] are the atmospheric concentrations of soluble and total Fe, respectively. However, the numerous factors affecting the soluble Fe fraction have not been fully understood. In this study, the Fe species, chemical composition, and soluble Fe concentrations in aerosols collected in Tsukuba, Japan were investigated over a year (nine samples from December 2002 to October 2003 to identify the factors affecting the amount of soluble Fe supplied into the ocean. The soluble Fe concentration in aerosols is correlated with those of sulfate and oxalate originated from anthropogenic sources, suggesting that soluble Fe is mainly derived from anthropogenic sources. Moreover, the soluble Fe concentration is also correlated with the enrichment factors of vanadium and nickel emitted by fossil fuel combustion. These results suggest that the degree of Fe dissolution is influenced by the magnitude of anthropogenic activity, such as fossil fuel combustion. X-ray absorption fine structure (XAFS spectroscopy was performed in order to identify the Fe species in aerosols. Fitting of XAFS spectra coupled with micro X-ray fluorescence analysis (μ-XRF showed the main Fe species in aerosols in Tsukuba to be illite, ferrihydrite, hornblende, and Fe(III sulfate. Moreover, the soluble Fe fraction in each sample measured by leaching experiments is closely correlated with the Fe(III sulfate fraction determined by the XAFS spectrum fitting, suggesting that Fe(III sulfate is the main soluble Fe in the ocean. Another possible factor that can control the amount of soluble Fe supplied into the ocean is the total Fe(III concentration in the atmosphere, which was high in spring due to the high

Synthesis and solubility measurement in supercritical carbon dioxide of two solid derivatives of 2-methylnaphthalene-1,4-dione (menadione): 2-(Benzylamino)-3-methylnaphthalene-1,4-dione and 3-(phenethylamino)-2-methylnaphthalene-1,4-dione

International Nuclear Information System (INIS)

Zacconi, Flavia C.; Nuñez, Olga N.; Cabrera, Adolfo L.; Valenzuela, Loreto M.

2016-01-01

Highlights: • Two menadione derivatives were synthesized, purified and characterized. • Solubility of menadione derivatives in SC-CO 2 was measured at T < 333 K, p < 28 MPa. • Thermodynamic consistency of solubility data measured was evaluated. • Solubility data was correlated in terms of temperature and CO 2 density. - Abstract: Synthesis of two solid derivatives of vitamin K 3 (2-methylnaphthalene-1,4-dione or menadione), 2-(benzylamino)-3-methylnaphthalene-1,4-dione and 3-(phenethylamino)-2-methylnaphthalene-1,4-dione was completed using a 1,4 Michael addition reaction at 323 K in an inert atmosphere, with reaction yields of 62% mol·mol −1 and 71% mol·mol −1 , respectively, and a purity grade of 98% mol·mol −1 for each component. Isothermal solubility (mole fraction) of each solid derivative in supercritical carbon dioxide was performed using an analytic-recirculation methodology, with direct determination of the molar composition of the carbon dioxide-rich phase by using high performance liquid chromatography, at temperatures of (313, 323 and 333) K and pressures from (8–28) MPa. Results indicated that the range of measured solubilities were from (59 × 10 −6 to 368 × 10 −6 ) mol·mol −1 for solid 2-(benzylamino)-3-methylnaphthalene-1,4-dione and from (40 × 10 −6 to 205 × 10 −6 ) mol·mol −1 for solid 3-(phenethylamino)-2-methylnaphthalene-1,4-dione. The experimental solubility was validated using three approaches, estimating the combined expanded uncertainty of measurement for each solubility data point, evaluating the thermodynamic consistency of the data utilizing a test based on the Gibbs–Duhem equation, and verifying the self-consistency by correlating the experimental solubility values with a semi-empirical model as a function of temperature, pressure and pure carbon dioxide density.

Combined Effects of Supersaturation Rates and Doses on the Kinetic-Solubility Profiles of Amorphous Solid Dispersions Based on Water-Insoluble Poly(2-hydroxyethyl methacrylate) Hydrogels.

Science.gov (United States)

Schver, Giovanna C R M; Lee, Ping I

2018-05-07

Under nonsink dissolution conditions, the kinetic-solubility profiles of amorphous solid dispersions (ASDs) based on soluble carriers typically exhibit so-called "spring-and-parachute" concentration-time behaviors. However, the kinetic-solubility profiles of ASDs based on insoluble carriers (including hydrogels) are known to show sustained supersaturation during nonsink dissolution through a matrix-regulated diffusion mechanism by which the supersaturation of the drug is built up gradually and sustained over an extended period without any dissolved polymers acting as crystallization inhibitors. Despite previous findings demonstrating the interplay between supersaturation rates and total doses on the kinetic-solubility profiles of soluble amorphous systems (including ASDs based on dissolution-regulated releases from soluble polymer carriers), the combined effects of supersaturation rates and doses on the kinetic-solubility profiles of ASDs based on diffusion-regulated releases from water-insoluble carriers have not been investigated previously. Thus, the objective of this study is to examine the impacts of total doses and supersaturation-generation rates on the resulting kinetic-solubility profiles of ASDs based on insoluble hydrogel carriers. We employed a previously established ASD-carrier system based on water-insoluble-cross-linked-poly(2-hydroxyethyl methacrylate) (PHEMA)-hydrogel beads and two poorly water soluble model drugs: the weakly acidic indomethacin (IND) and the weakly basic posaconazole (PCZ). Our results show clearly for the first time that by using the smallest-particle-size fraction and a high dose (i.e., above the critical dose), it is indeed possible to significantly shorten the duration of sustained supersaturation in the kinetic-solubility profile of an ASD based on a water-insoluble hydrogel carrier, such that it resembles the spring-and-parachute dissolution profiles normally associated with ASDs based on soluble carriers. This generates

Solubility Limits of Dibutyl Phosphoric Acid in Uranium Solutions at SRS

International Nuclear Information System (INIS)

Thompson, M.C.; Pierce, R.A.; Ray, R.J.

1998-06-01

The Savannah River Site has enriched uranium (EU) solution which has been stored for almost 10 years since being purified in the second uranium cycle of the H area solvent extraction process. The concentrations in solution are 6 g/L U and about 0.1 M nitric acid. Residual tributylphosphate in the solutions has slowly hydrolyzed to form dibutyl phosphoric acid (HDBP) at concentrations averaging 50 mg/L. Uranium is known to form compounds with DBP which have limited solubility. The potential to form uranium-DBP solids raises a nuclear criticality safety issue. SRTC tests have shown that U-DBP solids will precipitate at concentrations potentially attainable during storage of enriched uranium solutions. Evaporation of the existing EUS solution without additional acidification could result in the precipitation of U-DBP solids if DBP concentration in the resulting solution exceeds 110 ppm at ambient temperature. The same potential exists for evaporation of unwashed 1CU solutions. The most important variables of interest for present plant operations are HNO 3 and DBP concentrations. Temperature is also an important variable controlling precipitation. The data obtained in these tests can be used to set operating and safety limits for the plant. It is recommended that the data for 0 degrees C with 0.5 M HNO 3 be used for setting the limits. The limit would be 80 mg/L which is 3 standard deviations below the average of 86 observed in the tests. The data shows that super-saturation can occur when the DBP concentration is as much as 50 percent above the solubility limit. However, super-saturation cannot be relied on for maintaining nuclear criticality safety. The analytical method for determining DBP concentration in U solutions was improved so that analyses for a solution are accurate to within 10 percent. However, the overall uncertainty of results for periodic samples of the existing EUS solutions was only reduced slightly. Thus, sampling appears to be the largest portion

Use of the co-grinding method to enhance the dissolution behavior of a poorly water-soluble drug: generation of solvent-free drug-polymer solid dispersions.

Science.gov (United States)

Yang, Caiqin; Xu, Xiujuan; Wang, Jing; An, Zhiqian

2012-01-01

The solid dispersion (SD) technique is the most effective method for improving the dissolution rate of poorly water-soluble drugs. In the present work, SDs of the Ca2+ channel blocker dipfluzine (DF) with polyvinylpyrrolidone K30 (PVP) and poloxamer 188 (PLXM) were prepared by the powder solid co-grinding method under a solvent-free condition. The properties of all SDs and physical mixtures were investigated by X-ray diffraction, Fourier-transform infrared, differential scanning calorimetry, scanning electron microscopy, dissolution test, and particles size determination. Eutectic compounds were produced between the DF and PLXM matrix during the co-grinding process, whereas glass suspension formed in the SDs with PVP carrier. Hydrogen bond formation was not observed between DF and carriers and DF was microcrystalline state in the PVP and PLXM matrices. The solubility of DF in different concentration of carriers at 25, 31, and 37°C was investigated; the values obtained were used to calculate the thermodynamic parameters of interaction between DF and carriers. The Gibbs free energy (ΔrGθ) values were negative, indicating the spontaneous nature of dispersing DF into the carriers. Moreover, entropy is the drive force when DF disperses into the matrix of PVP, while, enthalpy-driven dispersing encounters in the PLXM carrier. All the SDs of DF/carriers showed a considerably higher dissolution rate than pure DF and the corresponding physical mixtures. The cumulative dissolution rate at 10 min of the SD with a 1 : 3 DF/carrier ratio increased 5.1-fold for PVP and 5.5-fold for PLXM.

The effects of disordered structure on the solubility and dissolution rates of some hydrophilic, sparingly soluble drugs.

Science.gov (United States)

Mosharraf, M; Sebhatu, T; Nyström, C

1999-01-15

The effects of experimental design on the apparent solubility of two sparingly soluble hydrophilic compounds (barium sulphate and calcium carbonate) were studied in this paper. The apparent solubility appeared to be primarily dependent on the amount of solute added to the solvent in each experiment, increasing with increased amounts. This effect seems to be due to the existence of a peripheral disordered layer. However physico-chemical methods used in the present study were not able to unambiguously verify the existence of any disorder in the solid state structure of the drugs. At higher proportions of solute to solvent, the solubility reached a plateau corresponding to the solubility of the disordered or amorphous molecular form of the material. Milling the powders caused the plateau to be reached at lower proportions of solute to solvent, since this further disordered the surface of the drug particles. It was also found that the apparent solubility of the drugs tested decreased after storage at high relative humidities. A model for describing the effects of a disordered surface layer of varying thickness and continuity on the solubility of a substance is presented. This model may be used as a method for detection of minute amount of disorder, where no other technique is capable of detecting the disordered structure. It is suggested that recrystallisation of the material occurs via slow solid-state transition at the surface of the drug particle; this would slowly reduce the apparent solubility of the substance at the plateau level to the thermodynamically stable value. A biphasic dissolution rate profile was obtained. The solubility of the disordered surface of the particles appeared to be the rate-determining factor during the initial dissolution phase, while the solubility of the crystalline core was the rate-determining factor during the final slower phase.

Thermodynamic modeling of neptunium(V) solubility in concentrated Na-CO3-HCO3-Cl-ClO4-H-OH-H2O systems

International Nuclear Information System (INIS)

Novak, C.F.; Roberts, K.E.

1994-01-01

Safety assessments of nuclear waste repositories often require estimation of actinide solubilities as a function of groundwater composition. Although considerable amount of research has been done on the solubility and speciation of actinides, relatively little has been done to unify these data into a model applicable to concentrate brines. Numerous authors report data on the aqueous chemical properties of Np(V) in NaClO 4 , Na 2 CO 3 , and NaCl media, but a consistent thermodynamic model for predicting these properties is not available. To meet this need, a model was developed to describe the solubility of Np(V) in Na-Cl-ClO 4 -CO 3 aqueous systems, based on the Pitzer activity coefficient formalism for concentrated electrolytes. Hydrolysis and/or carbonate complexation are the dominant aqueous reactions with neptunyl in these systems. Literature data for neptunyl extraction and solubility, and solubility data that the authors developed, are used to parameterize an integrated model for Np(V) solubility in the Np(V)-Na-CO 3 -HCO 3 -Cl-ClO 4 -H-OH-H 2 O system. The resulting model is tested against additional solubility data, and compared with Np(V) solubility experiments in complex synthetic brines

NEARSOL, Aqueous Speciation and Solubility of Actinides for Waste Disposal

International Nuclear Information System (INIS)

Leach, S.J.; Pryke, D.C.

1989-01-01

A - Description of program or function: NEARSOL models the aqueous speciation and solubility of actinides under near-field conditions for disposal using a simple thermodynamic approach. B - Method of solution: The program draws information from a thermodynamic data base consisting of solubility products and complex formation constants for all known species, and standard electrode potentials, at 25 C, corrected for ionic strength effects. By minimising the free energy of the system through a series of iterations, a precipitating solid phase is predicted which limits the solubility, and the concentration of the main aqueous species are calculated as a function of pH. Initially the program evaluates only hydroxide and carbonate species, but the effect of sulphate, phosphate and fluoride anions can also be included. The program is simple to use, requiring inputs of: 1. Actinide(s); 2. pH range; 3. Ionic strength; 4. Redox conditions; 5. Ligand concentrations. Functions are included to calculate the distribution of the protonated and un-protonated forms of carbonate and phosphate and the value of Eh as a function of pH under disposal conditions as required. The program can further evaluate the role of free calcium ions. C - Restrictions on the complexity of the problem: None

Predicting pear (cv. Clara Frijs) dry matter and soluble solids content with near infrared spectroscopy

DEFF Research Database (Denmark)

Travers, Sylvia; Bertelsen, Marianne; Petersen, Karen

2014-01-01

Regression models for predicting preharvest dry matter (DM) and soluble solids content (SSC), based on two spectral ranges (680-1000 nm and 1100-2350 nm), were compared. Models based on longer NIR spectra were more successful for both parameters (DM/SSC: R2 = 0.78-0.84; RMECV = 0.78/0.44; LVs = 6....../7). SSC prediction was better than expected considering the presence of starch in fruit. Generally poor SSC prediction in the presence of starch could be related to the inability of models to distinguish between forms of carbohydrate. Variable selection and regression coefficients highlighted...... fruit. Further research is needed to qualify and build on the results presented here....

Feasibility of using acoustic velocity meters for estimating highly organic suspended-solids concentrations in streams

Science.gov (United States)

Patino, Eduardo

1996-01-01

A field experiment was conducted at the Levee 4 canal site below control structure G-88 in the Everglades agricultural area in northwestern Broward County, Florida, to study the relation of acoustic attenuation to suspended-solids concentrations. Acoustic velocity meter and temperature data were obtained with concurrent water samples analyzed for suspended-solids concentrations. Two separate acoustic velocity meter frequencies were used, 200 and 500 kilohertz, to determine the sensitivity of acoustic attenuation to frequency for the measured suspended-solids concentration range. Suspended-solids concentrations for water samples collected at the Levee 4 canal site from July 1993 to September 1994 ranged from 22 to 1,058 milligrams per liter, and organic content ranged from about 30 to 93 percent. Regression analyses showed that attenuation data from the acoustic velocity meter (automatic gain control) and temperature data alone do not provide enough information to adequately describe the concentrations of suspended solids. However, if velocity is also included as one of the independent variables in the regression model, a satisfactory correlation can be obtained. Thus, it is feasible to use acoustic velocity meter instrumentation to estimate suspended-solids concentrations in streams, even when suspended solids are primarily composed of organic material. Using the most comprehensive data set available for the study (500 kiloherz data), the best fit regression model produces a standard error of 69.7 milligrams per liter, with actual errors ranging from 2 to 128 milligrams per liter. Both acoustic velocity meter transmission frequencies of 200 and 500 hilohertz produced similar results, suggesting that transducers of either frequency could be used to collect attenuation data at the study site. Results indicate that calibration will be required for each acoustic velocity meter system to the unique suspended-solids regime existing at each site. More robust solutions may

Solid Phospholipid Dispersions for Oral Delivery of Poorly Soluble Drugs

DEFF Research Database (Denmark)

Fong, Sophia Yui Kau; Martins, Susana A. M.; Brandl, Martin

2016-01-01

Celecoxib (CXB) is a Biopharmaceutical Classification System class II drug in which its oral bioavailability is limited by poor aqueous solubility. Although a range of formulations aiming to increase the solubility of CXB have been developed, it is not completely understood, whether (1) an increase...... the importance of evaluating both, solubility and permeability, and the use of biorelevant medium for testing the candidate-enabling performance of liposomal formulations. Mechanisms at molecular level that may explain the effect of PL formulations on the permeability of CXB are also discussed....

Predicting the equilibrium solubility of solid polycyclic aromatic hydrocarbons and dibenzothiophene using a combination of MOSCED plus molecular simulation or electronic structure calculations

Science.gov (United States)

Phifer, Jeremy R.; Cox, Courtney E.; da Silva, Larissa Ferreira; Nogueira, Gabriel Gonçalves; Barbosa, Ana Karolyne Pereira; Ley, Ryan T.; Bozada, Samantha M.; O'Loughlin, Elizabeth J.; Paluch, Andrew S.

2017-06-01

Methods to predict the equilibrium solubility of non-electrolyte solids are important for the design of novel separation processes. Here we demonstrate how conventional molecular simulation free energy calculations or electronic structure calculations in a continuum solvent, here SMD or SM8, can be used to predict parameters for the MOdified Separation of Cohesive Energy Density (MOSCED) method. The method is applied to the solutes naphthalene, anthracene, phenanthrene, pyrene and dibenzothiophene, compounds of interested to the petroleum industry and for environmental remediation. Adopting the melting point temperature and enthalpy of fusion of these compounds from experiment, we are able to predict equilibrium solubilities. Comparing to a total of 422 non-aqueous and 193 aqueous experimental solubilities, we find the proposed method is able to well correlate the data. The use of MOSCED is additionally advantageous as it is a solubility parameter-based method useful for intuitive solvent selection and formulation.

Novel electrosprayed nanospherules for enhanced aqueous solubility and oral bioavailability of poorly water-soluble fenofibrate

Directory of Open Access Journals (Sweden)

Yousaf AM

2016-01-01

Full Text Available Abid Mehmood Yousaf,1,2 Omer Mustapha,1 Dong Wuk Kim,1 Dong Shik Kim,1 Kyeong Soo Kim,1 Sung Giu Jin,1 Chul Soon Yong,3 Yu Seok Youn,4 Yu-Kyoung Oh,5 Jong Oh Kim,3 Han-Gon Choi1 1College of Pharmacy and Institute of Pharmaceutical Science and Technology, Hanyang University, Ansan, Gyeonggi, South Korea; 2Faculty of Pharmacy, University of Central Punjab, Johar, Lahore, Pakistan; 3College of Pharmacy, Yeungnam University, Gyongsan, North Gyeongsang, 4School of Pharmacy, Sungkyunkwan University, Suwon, Gyeonggi, 5College of Pharmacy, Seoul National University, Seoul, South Korea Purpose: The purpose of the present research was to develop a novel electrosprayed nanospherule providing the most optimized aqueous solubility and oral bioavailability for poorly water-soluble fenofibrate.Methods: Numerous fenofibrate-loaded electrosprayed nanospherules were prepared with polyvinylpyrrolidone (PVP and Labrafil® M 2125 as carriers using the electrospray technique, and the effect of the carriers on drug solubility and solvation was assessed. The solid state characterization of an optimized formulation was conducted by scanning electron microscopy, powder X-ray diffraction, differential scanning calorimetry, and Fourier transform infrared spectroscopic analyses. Oral bioavailability in rats was also evaluated for the formulation of an optimized nanospherule in comparison with free drug and a conventional fenofibrate-loaded solid dispersion.Results: All of the electrosprayed nanospherule formulations had remarkably enhanced aqueous solubility and dissolution compared with free drug. Moreover, Labrafil M 2125, a surfactant, had a positive influence on the solubility and dissolution of the drug in the electrosprayed nanospherule. Increases were observed as the PVP/drug ratio increased to 4:1, but higher ratios gave no significant increases. In particular, an electrosprayed nanospherule composed of fenofibrate, PVP, and Labrafil M 2125 at the weight ratio of 1

About Error in Measuring Oxygen Concentration by Solid-Electrolyte Sensors

Directory of Open Access Journals (Sweden)

V. I. Nazarov

2008-01-01

Full Text Available The paper evaluates additional errors while measuring oxygen concentration in a gas mixture by a solid-electrolyte cell. Experimental dependences of additional errors caused by changes in temperature in a sensor zone, discharge of gas mixture supplied to a sensor zone, partial pressure in the gas mixture and fluctuations in oxygen concentrations in the air.

Solubility of radionuclides in a concrete environment for provisional safety analyses for SGT-E2

International Nuclear Information System (INIS)

Berner, U.

2014-08-01

Within stage 2 of the sectoral plan for deep geological repositories for radioactive waste in Switzerland, safety analyses are carried out. In the case of the repository for long lived intermediate level waste (ILW) retention mechanisms include the concentration limits of safety relevant elements in the pore water of the engineered concrete system. The present work describes the evaluation of solubility limits for the safety relevant elements Be, C, Cl, K, Ca, Co, Ni, Se, Sr, Zr, Nb, Mo, Tc, Pd, Ag, Sn, I, Cs, Sm, Eu, Ho, Pb, Po, Ra, Ac, Th, Pa, U, Np, Pu, Am and Cm in the pore water of a concrete system corresponding to a degradation stage characterised by portlandite saturation and by the absence of (Na,K)OH solutes. The term solubility limit denotes the maximum amount of an element dissolving in the pore solution of the considered chemical reference system. For a given solid phase equilibrium, thermodynamics predicts the amount of substance dissolving in the solution and describes the speciation of the considered element in solution. The principles of chemical equilibrium will be the primary work hypothesis in the present work. Solubility calculations were performed with the most recent version of GEMS/PSI using the PSI/Nagra Chemical Thermodynamic Data Base 12/07. The database was complemented with other datasets for elements that were not considered in the mentioned update. Reference values solubilities as well as lower and upper guideline values are evaluated. For many formation constants of solids and solutes, uncertainties are known and allow conveying lower and upper guideline values. In many cases it is not clear whether the most stable solid is formed. In such cases the (kinetically driven) formation of alternative solid phases is included in the derivation of reference and guideline values. Corresponding justifications are given for the individual elements and are an important part of this work. A similar report for an almost identical chemical

Solubility of radionuclides in a concrete environment for provisional safety analyses for SGT-E2

Energy Technology Data Exchange (ETDEWEB)

Berner, U.

2014-08-15

Within stage 2 of the sectoral plan for deep geological repositories for radioactive waste in Switzerland, safety analyses are carried out. In the case of the repository for long lived intermediate level waste (ILW) retention mechanisms include the concentration limits of safety relevant elements in the pore water of the engineered concrete system. The present work describes the evaluation of solubility limits for the safety relevant elements Be, C, Cl, K, Ca, Co, Ni, Se, Sr, Zr, Nb, Mo, Tc, Pd, Ag, Sn, I, Cs, Sm, Eu, Ho, Pb, Po, Ra, Ac, Th, Pa, U, Np, Pu, Am and Cm in the pore water of a concrete system corresponding to a degradation stage characterised by portlandite saturation and by the absence of (Na,K)OH solutes. The term solubility limit denotes the maximum amount of an element dissolving in the pore solution of the considered chemical reference system. For a given solid phase equilibrium, thermodynamics predicts the amount of substance dissolving in the solution and describes the speciation of the considered element in solution. The principles of chemical equilibrium will be the primary work hypothesis in the present work. Solubility calculations were performed with the most recent version of GEMS/PSI using the PSI/Nagra Chemical Thermodynamic Data Base 12/07. The database was complemented with other datasets for elements that were not considered in the mentioned update. Reference values solubilities as well as lower and upper guideline values are evaluated. For many formation constants of solids and solutes, uncertainties are known and allow conveying lower and upper guideline values. In many cases it is not clear whether the most stable solid is formed. In such cases the (kinetically driven) formation of alternative solid phases is included in the derivation of reference and guideline values. Corresponding justifications are given for the individual elements and are an important part of this work. A similar report for an almost identical chemical

Solubility of neptunium and technetium dioxides in a Yucca Mountain simulated groundwaters

International Nuclear Information System (INIS)

Kulyako, Yu.; Perevalov, S.; Malikov, D.; Myasoedov, B.; Atkins-Duffin, Cynthia E.

2005-01-01

Full text of publication follows: Solubility of NpO 2 and TcO 2 in the Yucca Mountain simulated ground waters J-13 and UE-25p-1 were studied. It is shown that contents of the dissolved neptunium and technetium in simulated groundwater (SGW) depend on solid/liquid phase ratio in these systems under ambient conditions. Average values of NpO 2 solubility in the suspensions of J-13 SGW are equal to (1.1±0.2) x 10 -6 M, (4.7±0.5) x 10 -6 M and (1.3±0.2) x 10 -5 M at solid/liquid ratios (mg/mL) of 0.4, 2.5 and 9.8 respectively. Average solubility values of NpO 2 in the suspensions of UE-25p-1 SGW are equal to (1.6±0.2) x 10 -7 M, (4.3±0.7) x 10 -7 M and (4.2±1.2) x 10 -6 M for solid/liquid ratios (mg/mL) of 1.2, 3.7 and 18.6, respectively. At equal solid/liquid ratios the solubility of NpO 2 in J-13 SGW is higher than that in UE-25p-1 SGW. At equal contents of solid phase in the suspensions solubility of TcO 2 in J-13 SGW are close to those in UE-25p-1 SGW and they are approximately proportional to the solid/liquid ratio. Average values of TcO 2 solubility in the suspensions of J-13 SGW are equal to (3.0±0.2) x 10 -5 M, (1.7±0.2) x 10 -4 , (6.2±0.2) x 10 -4 M at solid/liquid ratios (mg/mL) of 0.6, 4.8 and 15.5 respectively. Average values of TcO 2 solubility in the suspensions of UE-25p-1 SGW are equal to (5.8±0.3) x 10 -5 M, (2.2±0.1) x 10 -4 M and (3.8±0.2) x 10 -4 M at solid/liquid ratios 1.6, 7.0 and 13.6 (mg/mL) respectively. The dependence of solubility of NpO 2 and TcO 2 on solid/liquid ratio may be explained by the fact that transition of the neptunium and technetium from solid phase into the liquid one occurs on phase interface owing to the dissolving of Np(V) and Tc(VII) compounds being formed under ambient conditions. (authors)

Determination of subcellular concentrations of soluble carbohydrates in rose petals during opening by nonaqueous fractionation method combined with infiltration-centrifugation method.

Science.gov (United States)

Yamada, Kunio; Norikoshi, Ryo; Suzuki, Katsumi; Imanishi, Hideo; Ichimura, Kazuo

2009-11-01

Petal growth associated with flower opening depends on cell expansion. To understand the role of soluble carbohydrates in petal cell expansion during flower opening, changes in soluble carbohydrate concentrations in vacuole, cytoplasm and apoplast of petal cells during flower opening in rose (Rosa hybrida L.) were investigated. We determined the subcellular distribution of soluble carbohydrates by combining nonaqueous fractionation method and infiltration-centrifugation method. During petal growth, fructose and glucose rapidly accumulated in the vacuole, reaching a maximum when petals almost reflected. Transmission electron microscopy showed that the volume of vacuole and air space drastically increased with petal growth. Carbohydrate concentration was calculated for each compartment of the petal cells and in petals that almost reflected, glucose and fructose concentrations increased to higher than 100 mM in the vacuole. Osmotic pressure increased in apoplast and symplast during flower opening, and this increase was mainly attributed to increases in fructose and glucose concentrations. No large difference in osmotic pressure due to soluble carbohydrates was observed between the apoplast and symplast before flower opening, but total osmotic pressure was much higher in the symplast than in the apoplast, a difference that was partially attributed to inorganic ions. An increase in osmotic pressure due to the continued accumulation of glucose and fructose in the symplast may facilitate water influx into cells, contributing to cell expansion associated with flower opening under conditions where osmotic pressure is higher in the symplast than in the apoplast.

Development of novel cilostazol-loaded solid SNEDDS using a SPG membrane emulsification technique: Physicochemical characterization and in vivo evaluation.

Science.gov (United States)

Mustapha, Omer; Kim, Kyung Soo; Shafique, Shumaila; Kim, Dong Shik; Jin, Sung Giu; Seo, Youn Gee; Youn, Yu Seok; Oh, Kyung Taek; Lee, Beom-Jin; Park, Young Joon; Yong, Chul Soon; Kim, Jong Oh; Choi, Han-Gon

2017-02-01

The objective of this study was to develop a novel solid self-nanoemulsifying drug delivery system (SNEDDS) using a membrane emulsification technique involving Shirasu porous glass (SPG) which produced very small and uniform emulsion droplets, resulting in enhanced solubility, dissolution and oral bioavailability of poorly water-soluble cilostazol. The effects of carriers on the drug solubility were assessed, and pseudo-ternary phase diagrams were plotted. Among the liquid SNEDDS formulations tested, the liquid SNEDDS composed of peceol (oil), Tween 20 (surfactant) and Labrasol (cosurfactant) at a weight ratio of 15/55/30, produced the smallest emulsion droplet size. The cilostazol-loaded liquid SNEDDS formulation was suspended in the distilled water and subjected to SPG membrane emulsification. Calcium silicate was added as a solid carrier in this liquid SNEDDS, completely suspended and spray-dried, leading to the production of a cilostazol-loaded solid SNEDDS. The emulsion droplet size, solubility and dissolution of the emulsified solid SNEDDS were assessed as compared to the solid SNEDDS prepared without emulsification. Moreover, the physicochemical characteristics and pharmacokinetics in rats were evaluated with the emulsified solid SNEDDS. The emulsified solid SNEDDS provided significantly smaller and more uniform nanoemulsions than did the non-emulsified solid SNEDDS. The emulsified solid SNEDDS showed significantly higher drug solubility and dissolution as compared to the non-emulsified solid SNEDDS. The crystalline drug in it was converted into the amorphous state. Moreover, in rats, it gave significantly higher initial plasma concentrations and AUC compared to the drug powder, suggesting its improved oral bioavailability of cilostazol. Thus, this novel solid SNEDDS developed using a membrane emulsification technique represents a potentially powerful oral delivery system for cilostazol. Copyright © 2016 Elsevier B.V. All rights reserved.

Assessment of the radium-barium co-precipitation and its potential influence on the solubility of Ra in the near-field

Energy Technology Data Exchange (ETDEWEB)

Grandia, Fidel; Merino, Joan; Bruno, Jordi (Amphos XXI Consulting S.L., Barcelona (Spain))

2008-08-15

behaviour of the system can be described by the established aqueous-solid solution thermodynamic formalism and assuming that the system behaves ideally. In the case when 226Ra is released from a secondary source, like a UO{sub 2} precipitate away from the fuel but within the canister, there is not sufficient experimental information at the molecular level to establish when and how the system will reach equilibrium and, therefore, it is not clear to which extent the aqueous solid solution thermodynamic formalism can be applied. Nevertheless, the long contact times expected under repository conditions together with the small mass transfer processes involved would indicate that it is quite likely that equilibrium will be reached. Dedicated experimental investigations are under way in collaboration with INE-KFZ to establish the mechanism and rates of this critical process in order to support the solid solution thermodynamic approximation. We have performed a number of scoping calculations in order to establish the absolute and relative effects of RaBaSO{sub 4}(ss) formation on 226Ra solubility. We have assumed that the free volume per canister filled by water in case of intrusion is roughly 1 m3. By using the standard fuel dissolution rate of 1.0x10-7/y, and a congruent release of barium, the calculated radium and barium concentrations after one year of contact at the disposal time of 300,000 years (when the 226Ra content is largest), are 1.3x10-12 and 4.9x10-9 mol/L, respectively. If we apply the thermodynamics of aqueous-solid solution equilibria the resulting solid phase in equilibrium has a calculated nominal composition of (Ba{sub 0.99942}Ra{sub 0.00057})SO{sub 4} (ss) and the resulting dissolved Ra(II) is in the 10-11 mol/L range. This is in the upper range of any observed Ra(II) concentration in natural and anthropogenic environment. If the solubility of Ra(II) is assumed to be controlled by the precipitation of a pure sulphate phase, the resulting concentration is three

Assessment of the radium-barium co-precipitation and its potential influence on the solubility of Ra in the near-field

International Nuclear Information System (INIS)

Grandia, Fidel; Merino, Joan; Bruno, Jordi

2008-08-01

system can be described by the established aqueous-solid solution thermodynamic formalism and assuming that the system behaves ideally. In the case when 226 Ra is released from a secondary source, like a UO 2 precipitate away from the fuel but within the canister, there is not sufficient experimental information at the molecular level to establish when and how the system will reach equilibrium and, therefore, it is not clear to which extent the aqueous solid solution thermodynamic formalism can be applied. Nevertheless, the long contact times expected under repository conditions together with the small mass transfer processes involved would indicate that it is quite likely that equilibrium will be reached. Dedicated experimental investigations are under way in collaboration with INE-KFZ to establish the mechanism and rates of this critical process in order to support the solid solution thermodynamic approximation. We have performed a number of scoping calculations in order to establish the absolute and relative effects of RaBaSO 4 (ss) formation on 226 Ra solubility. We have assumed that the free volume per canister filled by water in case of intrusion is roughly 1 m 3 . By using the standard fuel dissolution rate of 1.0x10 -7 /y, and a congruent release of barium, the calculated radium and barium concentrations after one year of contact at the disposal time of 300,000 years (when the 226 Ra content is largest), are 1.3x10 -12 and 4.9x10 -9 mol/L, respectively. If we apply the thermodynamics of aqueous-solid solution equilibria the resulting solid phase in equilibrium has a calculated nominal composition of (Ba 0.99942 Ra 0.00057 )SO 4 (ss) and the resulting dissolved Ra(II) is in the 10 -11 mol/L range. This is in the upper range of any observed Ra(II) concentration in natural and anthropogenic environment. If the solubility of Ra(II) is assumed to be controlled by the precipitation of a pure sulphate phase, the resulting concentration is three orders of magnitude

[Application of characteristic NIR variables selection in portable detection of soluble solids content of apple by near infrared spectroscopy].

Science.gov (United States)

Fan, Shu-Xiang; Huang, Wen-Qian; Li, Jiang-Bo; Guo, Zhi-Ming; Zhaq, Chun-Jiang

2014-10-01

In order to detect the soluble solids content(SSC)of apple conveniently and rapidly, a ring fiber probe and a portable spectrometer were applied to obtain the spectroscopy of apple. Different wavelength variable selection methods, including unin- formative variable elimination (UVE), competitive adaptive reweighted sampling (CARS) and genetic algorithm (GA) were pro- posed to select effective wavelength variables of the NIR spectroscopy of the SSC in apple based on PLS. The back interval LS- SVM (BiLS-SVM) and GA were used to select effective wavelength variables based on LS-SVM. Selected wavelength variables and full wavelength range were set as input variables of PLS model and LS-SVM model, respectively. The results indicated that PLS model built using GA-CARS on 50 characteristic variables selected from full-spectrum which had 1512 wavelengths achieved the optimal performance. The correlation coefficient (Rp) and root mean square error of prediction (RMSEP) for prediction sets were 0.962, 0.403°Brix respectively for SSC. The proposed method of GA-CARS could effectively simplify the portable detection model of SSC in apple based on near infrared spectroscopy and enhance the predictive precision. The study can provide a reference for the development of portable apple soluble solids content spectrometer.

Towards improved solubility of poorly water-soluble drugs: cryogenic co-grinding of piroxicam with carrier polymers.

Science.gov (United States)

Penkina, Anna; Semjonov, Kristian; Hakola, Maija; Vuorinen, Sirpa; Repo, Timo; Yliruusi, Jouko; Aruväli, Jaan; Kogermann, Karin; Veski, Peep; Heinämäki, Jyrki

2016-01-01

Amorphous solid dispersions (SDs) open up exciting opportunities in formulating poorly water-soluble active pharmaceutical ingredients (APIs). In the present study, novel catalytic pretreated softwood cellulose (CPSC) and polyvinylpyrrolidone (PVP) were investigated as carrier polymers for preparing and stabilizing cryogenic co-ground SDs of poorly water-soluble piroxicam (PRX). CPSC was isolated from pine wood (Pinus sylvestris). Raman and Fourier transform infrared (FTIR) spectroscopy, X-ray powder diffraction (XRPD) and differential scanning calorimetry (DSC) were used for characterizing the solid-state changes and drug-polymer interactions. High-resolution scanning electron microscope (SEM) was used to analyze the particle size and surface morphology of starting materials and final cryogenic co-ground SDs. In addition, the molecular aspects of drug-polymer interactions and stabilization mechanisms are presented. The results showed that the carrier polymer influenced both the degree of amorphization of PRX and stabilization against crystallization. The cryogenic co-ground SDs prepared from PVP showed an enhanced dissolution rate of PRX, while the corresponding SDs prepared from CPSC exhibited a clear sustained release behavior. In conclusion, cryogenic co-grinding provides a versatile method for preparing amorphous SDs of poorly water-soluble APIs. The solid-state stability and dissolution behavior of such co-ground SDs are to a great extent dependent on the carrier polymer used.

Concentration Impedance in Testing of Solid Oxide Cells Revisited

DEFF Research Database (Denmark)

Mogensen, Mogens Bjerg; Ebbesen, Sune Dalgaard; Jensen, Søren Højgaard

2017-01-01

The concentration impedance originating from diffusion and reactant conversion impedance of the Ni-YSZ supported fuel electrode in solid oxide cell has been treated many times during the latest couple of decades. In spite of this, the separation of the diffusion impedance from the conversion...

Oral formulation strategies to improve solubility of poorly water-soluble drugs.

Science.gov (United States)

Singh, Abhishek; Worku, Zelalem Ayenew; Van den Mooter, Guy

2011-10-01

In the past two decades, there has been a spiraling increase in the complexity and specificity of drug-receptor targets. It is possible to design drugs for these diverse targets with advances in combinatorial chemistry and high throughput screening. Unfortunately, but not entirely unexpectedly, these advances have been accompanied by an increase in the structural complexity and a decrease in the solubility of the active pharmaceutical ingredient. Therefore, the importance of formulation strategies to improve the solubility of poorly water-soluble drugs is inevitable, thus making it crucial to understand and explore the recent trends. Drug delivery systems (DDS), such as solid dispersions, soluble complexes, self-emulsifying drug delivery systems (SEDDS), nanocrystals and mesoporous inorganic carriers, are discussed briefly in this review, along with examples of marketed products. This article provides the reader with a concise overview of currently relevant formulation strategies and proposes anticipated future trends. Today, the pharmaceutical industry has at its disposal a series of reliable and scalable formulation strategies for poorly soluble drugs. However, due to a lack of understanding of the basic physical chemistry behind these strategies, formulation development is still driven by trial and error.

Equilibrium solubility measurement of ionizable drugs – consensus recommendations for improving data quality

Directory of Open Access Journals (Sweden)

Alex Avdeef

2016-06-01

Full Text Available This commentary addresses data quality in equilibrium solubility measurement in aqueous solution. Broadly discussed is the “gold standard” shake-flask (SF method used to measure equilibrium solubility of ionizable drug-like molecules as a function of pH. Many factors affecting the quality of the measurement are recognized. Case studies illustrating the analysis of both solution and solid state aspects of solubility measurement are presented. Coverage includes drug aggregation in solution (sub-micellar, micellar, complexation, use of mass spectrometry to assess aggregation in saturated solutions, solid state characterization (salts, polymorphs, cocrystals, polymorph creation by potentiometric method, solubility type (water, buffer, intrinsic, temperature, ionic strength, pH measurement, buffer issues, critical knowledge of the pKa, equilibration time (stirring and sedimentation, separating solid from saturated solution, solution handling and adsorption to untreated surfaces, solubility units, and tabulation/graphic presentation of reported data. The goal is to present cohesive recommendations that could lead to better assay design, to result in improved quality of measurements, and to impart a deeper understanding of the underlying solution chemistry in suspensions of drug solids.

Quantitative cross-sectional measurement of solid concentration distribution in slurries using a wire-mesh sensor

International Nuclear Information System (INIS)

Dos Santos, Eduardo Nunes; Da Silva, Marco Jose; Schleicher, Eckhard; Reinecke, Sebastian; Hampel, Uwe

2016-01-01

Wire-mesh sensors have so far been widely applied in gas–liquid flows where resistance or capacitance distributions are measured and converted into gas or liquid holdup distributions. In this work we report on the qualification of the wire-mesh imaging technique for the measurement of cross-sectional solid concentrations in solid–liquid mixtures. As the dielectric constants of solid particles are different from those of gas, water or oil in the flow, measuring this property can be used as an indication of solid distribution. Experiments were performed in a stirred tank of 100 mm diameter equipped with a capacitance wire-mesh sensor. The wire-mesh sensor was operated at an acquisition speed of 4000 frames per second and has a spatial resolution of 6.25 mm. As solids we used silica sand particles (diameter ∼250 μm) which were suspended in water in a volume concentration range of 1% to 35% to form slurries. By varying the stirring speed, different solid concentration distributions were produced and investigated. In order to convert the measured relative permittivity distribution into a solid concentration distribution, an empirical approach was employed. (paper)

A Systematic Study of Molecular Interactions of Anionic Drugs with a Dimethylaminoethyl Methacrylate Copolymer Regarding Solubility Enhancement.

Science.gov (United States)

Saal, Wiebke; Ross, Alfred; Wyttenbach, Nicole; Alsenz, Jochem; Kuentz, Martin

2017-04-03

The methacrylate-copolymer Eudragit EPO (EPO) has raised interest in solubility enhancement of anionic drugs. Effects on aqueous drug solubility at rather low polymer concentrations are barely known despite their importance upon dissolution and dilution of oral dosage forms. We provide evidence for substantial enhancement (factor 4-230) of aqueous solubility of poorly water-soluble anionic drugs induced by low (0.1-5% (w/w)) concentration of EPO for a panel of seven acidic crystalline drugs. Diffusion data (determined by 1 H nuclear magnetic resonance spectroscopy) indicate that the solubility increasing effect monitored by quantitative ultraperformance liquid chromatography was caused primarily by molecular API polymer interactions in the bulk liquid phase. Residual solid API remained unaltered as tested by X-ray powder diffraction. The solubility enhancement (SE) revealed a significant rank correlation (r Spearman = -0.83) with rDiff API , where SE and rDiff API are defined ratios of solubility and diffusion coefficient in the presence and absence of EPO. SE decreased in the order of indomethacin, mefenamic acid, warfarin, piroxicam, furosemide, bezafibrate, and tolbutamide. The solubilizing effect was attributed to both ionic and hydrophobic interactions between drugs and EPO. The excellent solubilizing properties of EPO are highly promising for pharmaceutical development, and the data set provides first steps toward an understanding of drug-excipient interaction mechanisms.

Glucose, fructose and sucrose increase the solubility of protein-tannin complexes and at high concentration, glucose and sucrose interfere with bisulphite bleaching of wine pigments.

Science.gov (United States)

Harbertson, James F; Yuan, Chunlong; Mireles, Maria S; Hanlin, Rachel L; Downey, Mark O

2013-05-01

Wines were modified with increasing sugar concentrations and decreasing tannin concentrations and analysed by a combination of protein precipitation and bisulphite bleaching. Increasing sugar concentration decreased the precipitation of tannin and protein-precipitable polymeric pigments (PPP). The use of a hydrogen bond disruptor (urea) to reduce protein-tannin and protein-pigment complex formation showed that the effect of sugar concentration occurred by increasing the solubility of the tannin-protein complex, not by interfering with protein-tannin complex formation. By increasing the solubility of pigment-protein complexes, non-protein-precipitable polymeric pigments (nPPP) appeared to increase. There was also an increase in total polymeric pigments at each tannin concentration with increasing glucose and sucrose concentration, indicating that sugar concentration might also affect bisulphite bleaching of wine pigments. While a significant effect of sugar concentration on tannin-protein complex solubility was observed, these effects were greatest at sugar concentrations far in excess of normal wine making conditions. Under normal wine making conditions, sugar concentration will have a negligible effect on protein-precipitable tannin, PPP and nPPP concentrations. Copyright © 2012 Elsevier Ltd. All rights reserved.

Corrosion and solubility in a TSP-buffered chemical environment following a loss of coolant accident: Part 1 – Aluminum

Energy Technology Data Exchange (ETDEWEB)

Howe, Kerry J., E-mail: howe@unm.edu [University of New Mexico, 210 University Blvd., Albuquerque, NM 87131 (United States); Mitchell, Lana, E-mail: lmitchell@alionscience.com [University of New Mexico, 210 University Blvd., Albuquerque, NM 87131 (United States); Kim, Seung-Jun, E-mail: skim@lanl.gov [University of New Mexico, 210 University Blvd., Albuquerque, NM 87131 (United States); Blandford, Edward D., E-mail: edb@unm.edu [University of New Mexico, 210 University Blvd., Albuquerque, NM 87131 (United States); Kee, Ernest J., E-mail: erniekee@gmail.com [South Texas Project Nuclear Operating Company, P.O. Box 270, Wadsworth, TX 77483 (United States)

2015-10-15

Highlights: • Trisodium phosphate (TSP) causes aluminum corrosion to cease after 24 h of exposure. • Chloride, iron, and copper have a minimal effect on the rate of aluminum corrosion when TSP is present. • Zinc can reduce the rate of aluminum corrosion when TSP is present. • Aluminum occasionally precipitates at concentrations lower than the calculated solubility for Al(OH){sub 3}. • Corrosion and solubility equations can be used to calculate the solids generated during a LOCA. - Abstract: Bench experiments were conducted to investigate the effect of the presence of trisodium phosphate (TSP) on the corrosion and release of aluminum from metallic aluminum surfaces under conditions representative of the containment pool following a postulated loss of coolant accident at a nuclear power generating facility. The experiments showed that TSP is capable of passivating the aluminum surface and preventing continued corrosion after about 24 h at the conditions tested. A correlation that describes the rate of corrosion including the passivation effect was developed from the bench experiments and validated with a separate set of experiments from a different test system. The saturation concentration of aluminum was shown to be well described by the solubility of amorphous aluminum hydroxide for the majority of cases, but instances have been observed when aluminum precipitates at concentrations lower than the calculated aluminum hydroxide solubility. Based on the experimental data and previous literature, an equation was developed to calculate the saturation concentration of aluminum as a function of pH and temperature under conditions representative of a loss of coolant accident (LOCA) in a TSP-buffered pressurized water reactor (PWR) containment. The corrosion equation and precipitation equation can be used in concert with each other to calculate the quantity of solids that would form as a function of time during a LOCA if the temperature and pH profiles were known.

Corrosion and solubility in a TSP-buffered chemical environment following a loss of coolant accident: Part 1 – Aluminum

International Nuclear Information System (INIS)

Howe, Kerry J.; Mitchell, Lana; Kim, Seung-Jun; Blandford, Edward D.; Kee, Ernest J.

2015-01-01

Highlights: • Trisodium phosphate (TSP) causes aluminum corrosion to cease after 24 h of exposure. • Chloride, iron, and copper have a minimal effect on the rate of aluminum corrosion when TSP is present. • Zinc can reduce the rate of aluminum corrosion when TSP is present. • Aluminum occasionally precipitates at concentrations lower than the calculated solubility for Al(OH) 3 . • Corrosion and solubility equations can be used to calculate the solids generated during a LOCA. - Abstract: Bench experiments were conducted to investigate the effect of the presence of trisodium phosphate (TSP) on the corrosion and release of aluminum from metallic aluminum surfaces under conditions representative of the containment pool following a postulated loss of coolant accident at a nuclear power generating facility. The experiments showed that TSP is capable of passivating the aluminum surface and preventing continued corrosion after about 24 h at the conditions tested. A correlation that describes the rate of corrosion including the passivation effect was developed from the bench experiments and validated with a separate set of experiments from a different test system. The saturation concentration of aluminum was shown to be well described by the solubility of amorphous aluminum hydroxide for the majority of cases, but instances have been observed when aluminum precipitates at concentrations lower than the calculated aluminum hydroxide solubility. Based on the experimental data and previous literature, an equation was developed to calculate the saturation concentration of aluminum as a function of pH and temperature under conditions representative of a loss of coolant accident (LOCA) in a TSP-buffered pressurized water reactor (PWR) containment. The corrosion equation and precipitation equation can be used in concert with each other to calculate the quantity of solids that would form as a function of time during a LOCA if the temperature and pH profiles were known

Solid dispersion application in pharmaceutical technology: Methods of preparation and characterization

OpenAIRE

Medarević, Đorđe; Ibrić, Svetlana; Đuriš, Jelena; Đurić, Zorica

2013-01-01

A growing number of newly synthesized drugs exhibit low aqueous solubility, leading to poor bioavailability. Therefore, improving drug solubility and dissolution rate became one of the greatest challenges during formulation development. Solid dispersions formulation is one of the commonly investigated techniques for improving solubility of poorly soluble drugs. Solid dispersions are dispersions of one or more drugs in an inert carrier (matrix) in the solid state prepared by melting, solvent, ...

Uranyl Oxalate Solubility

Energy Technology Data Exchange (ETDEWEB)

Leturcq, G.; Costenoble, S.; Grandjean, S. [CEA Marcoule DEN/DRCP/SCPS/LCA - BP17171 - 30207 Bagnols sur Ceze cedex (France)

2008-07-01

The solubility of uranyl oxalate was determined at ambient temperature by precipitation in oxalic-nitric solutions, using an initial uranyl concentration of 0.1 mol/L. Oxalic concentration varied from 0.075 to 0.3 mol/L while nitric concentration ranged between 0.75 and 3 mol/L. Dissolution tests, using complementary oxalic-nitric media, were carried out for 550 hours in order to study the kinetic to reach thermodynamic equilibrium. Similar solubility values were reached by dissolution and precipitation. Using the results, it was possible to draw the solubility surface versus oxalic and nitric concentrations and to determine both the apparent solubility constant of UO{sub 2}C{sub 2}O{sub 4}, 3H{sub 2}O (Ks) and the apparent formation constant of the first uranyl-oxalate complex UO{sub 2}C{sub 2}O{sub 4} (log {beta}1), for ionic strengths varying between 1 and 3 mol/L. Ks and log {beta}1 values were found to vary from 1.9 10{sup -8} to 9.2 10{sup -9} and from 5.95 to 6.06, respectively, when ionic strength varied from 1 to 3 mol/L. A second model may fit our data obtained at an ionic strength of 3 mol/L suggesting as reported by Moskvin et al. (1959) that no complexes are formed for [H{sup +}] at 3 M. The Ks value would then be 1.3 10{sup -8}. (authors)

Colloid-facilitated effects on migration of radionuclides in fractured rock with a kinetic solubility-limited dissolution model

International Nuclear Information System (INIS)

Jen Chunping; Tien Nengchuan

2010-01-01

Nuclides can move with groundwater either as solutes or colloids, where the latter mechanism generally results in much shorter traveling time as the nuclides interact strongly with solid phases, such as actinides. In the performance assessment, it is therefore essential to assess the relative importance of these two transport mechanisms for different nuclides. The relative importance of colloids depends on the nature and concentration of the colloids in groundwater. Plutonium (Pu), neptunium (Np), uranium (U) and americium (Am) are four nuclides of concern for the long-term emplacement of nuclear wastes at potential repository sites. These four actinides have a high potential for migrating if attached to iron oxide, clay or silica colloids in the groundwater.Strong sorption of the actinides by colloids in the groundwater may facilitate the transport of these nuclides along potential flow paths. The solubility-limited dissolution model can be used to assess the safety of the release of nuclear waste in geological disposal sites. Usually, it has been assumed that the solubility of the waste form is constant. If a nuclide reaches its solubility limit at an inner location near the waste form, it is unlikely that the same nuclide will reach its solubility limit at an outer location unless this nuclide has a parent nuclide. It is unlikely that the daughter nuclides will exceed their solubility limit due to decay of their parent nuclide. The present study investigates the effect of colloids on the transport of solubility-limited nuclides under the kinetic solubility-limited dissolution (KSLD) boundary condition in fractured media. The release rate of the nuclides is proportional to the difference between the saturation concentration and the inlet aqueous concentration of the nuclides. The presence of colloids decreases the aqueous concentration of nuclides and, thus, increases the release flux of nuclides from the waste form. (authors)

Characterization, in Vivo and in Vitro Evaluation of Solid Dispersion of Curcumin Containing d-α-Tocopheryl Polyethylene Glycol 1000 Succinate and Mannitol

Directory of Open Access Journals (Sweden)

Im-Sook Song

2016-10-01

Full Text Available The aim of this study was to prepare a solid dispersion formulation of curcumin to enhance its solubility, dissolution rate, and oral bioavailability. The formulation was prepared with d-α-tocopheryl polyethylene glycol 1000 succinate (TPGS and mannitol using solvent evaporation and freeze-drying methods, which yielded a solid dispersion composed of curcumin, TPGS, and mannitol at a ratio of 1:10:15 (w/w/w. The solubility and dissolution rate of the curcumin solid dispersion markedly improved compared with those of curcumin powder and a physical mixture of curcumin, TPGS, and mannitol. About 90% of the curcumin was released from the solid dispersion formulation within 10 min. After administering the formulation orally to rats, higher plasma concentrations of curcumin were observed, with increases in the maximum plasma concentration (Cmax and area under the plasma concentration-time curve (AUC of 86- and 65-fold, respectively, compared with those of curcumin powder. The solid dispersion formulation effectively increased intestinal permeability and inhibited P-gp function. These effects increased the anti-proliferative effect of curcumin in MDA-MB-231 breast cancer cells. Moreover, 2 h incubation with curcumin powder, solid dispersion formulation, and its physical mixture resulted in differential cytotoxic effect of paclitaxel in P-gp overexpressed LLC-PK1-P-gp and MDA-MB-231 cells through the inhibition of P-gp-mediated paclitaxel efflux. In conclusion, compared with curcumin, a solid dispersion formulation of curcumin with TPGS and mannitol could be a promising option for enhancing the oral bioavailability and efficacy of curcumin through increased solubility, dissolution rate, cell permeability, and P-gp modulation.

Characterization, in Vivo and in Vitro Evaluation of Solid Dispersion of Curcumin Containing d-α-Tocopheryl Polyethylene Glycol 1000 Succinate and Mannitol.

Science.gov (United States)

Song, Im-Sook; Cha, Jin-Sun; Choi, Min-Koo

2016-10-17

The aim of this study was to prepare a solid dispersion formulation of curcumin to enhance its solubility, dissolution rate, and oral bioavailability. The formulation was prepared with d-α-tocopheryl polyethylene glycol 1000 succinate (TPGS) and mannitol using solvent evaporation and freeze-drying methods, which yielded a solid dispersion composed of curcumin, TPGS, and mannitol at a ratio of 1:10:15 ( w / w / w ). The solubility and dissolution rate of the curcumin solid dispersion markedly improved compared with those of curcumin powder and a physical mixture of curcumin, TPGS, and mannitol. About 90% of the curcumin was released from the solid dispersion formulation within 10 min. After administering the formulation orally to rats, higher plasma concentrations of curcumin were observed, with increases in the maximum plasma concentration (C max ) and area under the plasma concentration-time curve (AUC) of 86- and 65-fold, respectively, compared with those of curcumin powder. The solid dispersion formulation effectively increased intestinal permeability and inhibited P-gp function. These effects increased the anti-proliferative effect of curcumin in MDA-MB-231 breast cancer cells. Moreover, 2 h incubation with curcumin powder, solid dispersion formulation, and its physical mixture resulted in differential cytotoxic effect of paclitaxel in P-gp overexpressed LLC-PK1-P-gp and MDA-MB-231 cells through the inhibition of P-gp-mediated paclitaxel efflux. In conclusion, compared with curcumin, a solid dispersion formulation of curcumin with TPGS and mannitol could be a promising option for enhancing the oral bioavailability and efficacy of curcumin through increased solubility, dissolution rate, cell permeability, and P-gp modulation.

The solubility of UO22+ in dilute sodium chloride solutions and in high-ionic strength sodium sulfate and chlorine brines

International Nuclear Information System (INIS)

Marquez, L.N.; Kadkhodayan, B.; Wruck, D.A.

1995-01-01

Uranium is a major component of high-level nuclear waste. In an oxidizing environment, UO 2 2+ would be expected to be the dominant dissolved species in solution. In addition to dilute solutions, because high-level nuclear waste may be stored in repositories containing salt, it is important to characterize the aqueous chemistry of UO 2 2+ and the solubility-controlling U(VI) solids in high-ionic strength brines as a function of pH. We have studied the solubility of UO 2 2+ by precipitation of solid phase in 0.001 molal NaCl, 5.2 molal NaCl, and saturated Na 2 SO 4 at pH values ranging from 5 to 12. The solution concentrations were measured by alpha particle liquid scintillation counting. The precipitated solids were characterized by powder x-ray diffraction, electron microscopy, infrared spectroscopy, and x-ray photoelectron spectroscopy

MFT homogeneity study at TNX: Final report on the low weight percent solids concentration

International Nuclear Information System (INIS)

Jenkins, W.J.

1993-01-01

A statistical design and analysis of both elemental analyses and weight percent solids analyses data was utilized to evaluate the MFT homogeneity at low heel levels and low agitator speed at both high and low solids feed concentrations. The homogeneity was also evaluated at both low and high agitator speed at the 6000+ gallons static level. The dynamic level portion of the test simulated feeding the Melter from the MFT to evaluate the uniformity of the solids slurry composition (Frit-PHA-Sludge) entering the melter from the MFT. This final report provides the results and conclusions from the second half of the study, the low weight percent solids concentration portion, as well as a comparison with the results from the first half of the study, the high weight percent solids portion

Separation of three water-soluble vitamins by poly(dimethylsiloxane) microchannel electrophoresis with electrochemical detection.

Science.gov (United States)

Li, Xiang-Yun; Zhang, Qian-Li; Lian, Hong-Zhen; Xu, Jing-Juan; Chen, Hong-Yuan

2007-09-01

A method for rapid separation and sensitive determination of three water-soluble vitamins, pyridoxine, ascorbic acid (VC), and p-aminobenzoic acid (PABA) has been developed by PDMS microchannel electrophoresis integrated with amperometric detection. After treatment of the microchip with oxygen plasma, the peak shapes of the three analytes were essentially improved. Pyridoxine, VC, and PABA were well separated within only 80 s in a running buffer of 20 mM borate solution (pH 8.5). Good linearity was obtained within the concentration range of 2-200 microM for the three water-soluble vitamins. The detection limits were 1.0 microM for pyridoxine and VC, and 1.5 microM for PABA. The proposed method has been successfully applied to real human urine sample, without solid phase extraction, with recoveries of 80-122% for the three water-soluble vitamins.

Swelling power and solubility of modified breadfruit flour using Lactobacillus plantarum

Science.gov (United States)

Norita Rahma, Istiana; Haris Pratama, Raja; Alfiyanti; Reynaldo Alwi, Deo; Astuti, Woro Indriani Setyo Tri; Hesti Wardhani, Dyah

2017-11-01

Breadfruit has the high nutritional and carbohydrate content which is comparable with wheat, so it is potential to be processed as the breadfruit flour. However, some studies showed the breadfruit flour has low swelling power (SP) and water solubility (WS) compared to wheat. Hence, the flour required modification. The main purpose of this research was to increase the value of SP and WS on breadfruit flour through a fermentation process. Sterile breadfruit flour (50 g) was suspended using sterile distilled water in a 250 ml glass beaker to obtain the flour concentration of 25%, 30%, 35%, 40% and 45% (g/ml). A certain concentration of L. plantarum was added (5, 7.5, 10, and 12.5%, ml/ml) then incubated at 30°C for 24, 48, 72, 96 and 120 h. The obtained solid cake was washed before being dried. The effect of cultural concentration on swelling power (SP) and water solubility (WS) is presented in Figure 1. The optimum fermentation condition was achieved by a 35% concentration of breadfruit flour which fermented with 10% L. plantarum for 24 h fermentation. At this condition, all parameter showed an increase of carbohydrate, protein, SP and WS into 84.761, 3.776, 8.870% and 0.136%, respectively.

IMPROVEMENT OF SOLUBILITY OF BADLY WATER SOLUBLE DRUG (IBUPROFEN) BY USING SURFACTANTS AND CARRIERS

OpenAIRE

Md. Zakaria Faruki*, Rishikesh, Elizabeth Razzaque, Mohiuddin Ahmed Bhuiyan

2013-01-01

ABSTRACT: Although there was a great interest in solid dispersion systems during the past four decades to increase dissolution rate and bioavailability of badly water-soluble drugs, their profitable use has been very limited, primarily because of manufacturing difficulties and stability problems. In this study solid solutions of drugs were generally produced by fusion method. The drug along with the excipients (surfactants and carriers) was heated first and then hardened by cooling to room te...

Solubility behavior of narcotic analgesics in aqueous media: solubilities and dissociation constants of morphine, fentanyl, and sufentanil.

Science.gov (United States)

Roy, S D; Flynn, G L

1989-02-01

The pH dependence of the aqueous solubility of morphine, fentanyl, and sufentanil was investigated at 35 degrees C. Dissociation constants and corresponding pKa' values of the drugs were obtained from measured free-base solubilities (determined at high pH's) and the concentrations of saturated solutions at intermediate pH's. Morphine, fentanyl, and sufentanil exhibited pKa' values of 8.08, 8.99, and 8.51, respectively. Over the pH range of 5 to 12.5 the apparent solubilities are determined by the intrinsic solubility of the free base plus the concentration of ionized drug necessary to satisfy the dissociation equilibrium at a given pH. Consequently, the drug concentrations of saturated aqueous solutions fall off precipitously as the pH is raised and ionization is suppressed. Further, at low pH's the aqueous solubility of morphine increased in a linear fashion with increases in the molar strength of citric acid which was added to acidify the medium, suggesting the formation of a soluble morphine-citrate complex.

Standardization and application of the solid phase C1q radioimmunoassay using soluble tetanus toxoid-antitetanus immune complexes in sera of patients with chronic polyarthritis and Lupus erythematodes

International Nuclear Information System (INIS)

Menzel, E.J.; Steffen, C.; Smolen, J.

1982-01-01

Soluble tetanus-antitetanus immune complexes were prepared with affinity-chromatography and gel chromatography. Serial dilutions of these immune complex preparations were tested in a solid phase C1q radioimmunoassay. Soluble immune complexes as well as aggregated human gamma globulin of identical protein concentrations were comparatively investigated. Soluble immune complexes rendered a more sensitive standardization of RIA. According to these observations a relation between μg/ml equivalents of defined tetanus-antitetanus complexes and ng second antibody obtained in C1q-RIA was calculated. Upper limit of mean values and two standard deviations of ng second antibody obtained in investigations of 55 normal sera was designated as 1 unit immune complexes and regarded as border line of negative results. Multiplication of μg/ml immune complex equivalents of 1 unit led to a scale of 1 to 15 units, showing the area of positive results. According to these values a standardization curve was constructed allowing a conversion of ng-second antibody obtained in serum investigations into immune complex units equivalent to defined standard immune complexes. With this curve investigation results of 56 RA sera and 21 SLE sera were expressed in the range of units, making a distinct gradation of positive results and a clear cut separation of positive and negative results possible. SLE sera of patients in acute stage showed highly positive results. (orig.) [de

Standardization and application of the solid phase C1q radioimmunoassay using soluble tetanus toxoid-antitetanus immune complexes in sera of patients with chronic polyarthritis and Lupus erythematodes

Energy Technology Data Exchange (ETDEWEB)

Menzel, E J; Steffen, C; Smolen, J

1982-11-22

Soluble tetanus-antitetanus immune complexes were prepared with affinity-chromatography and gel chromatography. Serial dilutions of these immune complex preparations were tested in a solid phase C1q radioimmunoassay. Soluble immune complexes as well as aggregated human gamma globulin of identical protein concentrations were comparatively investigated. Soluble immune complexes rendered a more sensitive standardization of RIA. According to these observations a relation between ..mu..g/ml equivalents of defined tetanus-antitetanus complexes and ng second antibody obtained in C1q-RIA was calculated. Upper limit of mean values and two standard deviations of ng second antibody obtained in investigations of 55 normal sera was designated as 1 unit immune complexes and regarded as border line of negative results. Multiplication of ..mu..g/ml immune complex equivalents of 1 unit led to a scale of 1 to 15 units, showing the area of positive results. According to these values a standardization curve was constructed allowing a conversion of ng-second antibody obtained in serum investigations into immune complex units equivalent to defined standard immune complexes. With this curve investigation results of 56 RA sera and 21 SLE sera were expressed in the range of units, making a distinct gradation of positive results and a clear cut separation of positive and negative results possible. SLE sera of patients in acute stage showed highly positive results.

The effect of ultrasonic pretreatment on biogas generation yield from organic fraction of municipal solid waste under medium solids concentration circumstance

International Nuclear Information System (INIS)

Rasapoor, Mazdak; Ajabshirchi, Yahya; Adl, Mehrdad; Abdi, Reza; Gharibi, Arash

2016-01-01

Highlights: • Ultrasonic pretreatment improved biogas yields at lower TS content samples. • Time of ultrasonication was significantly effective on maximum biogas yields. • Ultrasonic pretreatment can cause the release of TVFA content before digestion. • Specific energy between 5000 kJ/kg TS and 10,000 kJ/kg TS improved biogas yields. - Abstract: Hydrolysis is the most rate limiting step in almost all anaerobic digestion systems. To tackle long time duration, ultrasonic pretreatment proved that it can effectively improve biogas yield efficiency by effecting on soluble particles. In this study, the effect of three different ultrasonic power densities (0.2 W/mL, 0.4 W/mL and 0.6 W/mL) at three different times (10 min, 20 min and 30 min) on biogas yield of organic fraction of municipal solid waste (OFMSW) at three different total solid content (6%, 8% and 10%) were analyzed. Results showed significant (p < 0.01) effect of both sonication density and time of sonication on biogas final yield and biogas yield after 72 h digestion with the 6% TS content. Parameters like specific energy input and total volatile fatty acid (TVFA) content were also evaluated to find the best sonication treatments for OFMSW. For lower TS contents (6% and 8%), sonication treatment significantly (p < 0.01) increased TVFA concentration before digesting. It is also proved that specific energy input between 5000 kJ/kg TS and 10,000 kJ/kg TS can effectively increase the biogas yields, especially for 6% TS content, and caused maximum biogas yield produced after 72 h of digestion.

Both solubility and chemical stability of curcumin are enhanced by solid dispersion in cellulose derivative matrices.

Science.gov (United States)

Li, Bin; Konecke, Stephanie; Wegiel, Lindsay A; Taylor, Lynne S; Edgar, Kevin J

2013-10-15

Amorphous solid dispersions (ASD) of curcumin (Cur) in cellulose derivative matrices, hydroxypropylmethylcellulose acetate succinate (HPMCAS), carboxymethylcellulose acetate butyrate (CMCAB), and cellulose acetate adipate propionate (CAAdP) were prepared in order to investigate the structure-property relationship and identify polymer properties necessary to effectively increase Cur aqueous solution concentration. XRD results indicated that all investigated solid dispersions were amorphous, even at a 9:1 Cur:polymer ratio. Both stability against crystallization and Cur solution concentration from these ASDs were significantly higher than those from physical mixtures and crystalline Cur. Remarkably, curcumin was also stabilized against chemical degradation in solution. Chemical stabilization was polymer-dependent, with stabilization in CAAdP>CMCAB>HPMCAS>PVP, while matrices enhanced solution concentration as PVP>HPMCAS>CMCAB≈CAAdP. HPMCAS/Cur dispersions have useful combinations of pH-triggered release profile, chemical stabilization, and strong enhancement of Cur solution concentration. Copyright © 2013 Elsevier Ltd. All rights reserved.

Head-To-Head Comparison of Different Solubility-Enabling Formulations of Etoposide and Their Consequent Solubility-Permeability Interplay.

Science.gov (United States)

Beig, Avital; Miller, Jonathan M; Lindley, David; Carr, Robert A; Zocharski, Philip; Agbaria, Riad; Dahan, Arik

2015-09-01

The purpose of this study was to conduct a head-to-head comparison of different solubility-enabling formulations, and their consequent solubility-permeability interplay. The low-solubility anticancer drug etoposide was formulated in several strengths of four solubility-enabling formulations: hydroxypropyl-β-cyclodextrin, the cosolvent polyethylene glycol 400 (PEG-400), the surfactant sodium lauryl sulfate, and an amorphous solid dispersion formulation. The ability of these formulations to increase the solubility of etoposide was investigated, followed by permeability studies using the parallel artificial membrane permeability assay (PAMPA) and examination of the consequent solubility-permeability interplay. All formulations significantly increased etoposide's apparent solubility. The cyclodextrin-, surfactant-, and cosolvent-based formulations resulted in a concomitant decreased permeability that could be modeled directly from the proportional increase in the apparent solubility. On the contrary, etoposide permeability remained constant when using the ASD formulation, irrespective of the increased apparent solubility provided by the formulation. In conclusion, supersaturation resulting from the amorphous form overcomes the solubility-permeability tradeoff associated with other formulation techniques. Accounting for the solubility-permeability interplay may allow to develop better solubility-enabling formulations, thereby maximizing the overall absorption of lipophilic orally administered drugs. © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association.

The effect of different concentrations of water soluble azadirachtin (neem metabolite) on Streptococcus mutans compared with chlorhexidine.

Science.gov (United States)

Kankariya, Amit R; Patel, Alok R; Kunte, Sanket S

2016-01-01

Despite advances in the development of anticaries chemotherapy, the newer agents are unable to control the initiation of dental caries. Research and development of natural antibacterial agents that are safe for the host as well as specific for oral pathogens is awaited. Neem tree extracts have been used for thousands of years for maintaining overall well-being. Chewing neem sticks in the morning is the most common indigenous method of cleaning the mouth in rural population. This has generated the interest of the dentists for the use of neem for controlling dental diseases. This study aims to evaluate the quantitative and qualitative effect of different concentrations of water soluble azadirachtin (neem metabolite) on Streptococcus mutans (S. mutans) against chlorhexidine. Plaque was collected from 30 children aged 8-12 years reporting to the Department of Pediatric and Preventive Dentistry, Bharti Vidyapeeth Dental College, Pune and transported to the laboratory. After incubation of the plates the inhibitory zones were noted and the diameter of the zone of inhibition was measured and recorded to check the inhibition of growth of S. mutans. For testing the bacterial survival, the biofilms were prepared and colony forming units (CFU) was enumerated using a digital colony counter. Two-way analysis of variance (ANOVA) and Tukey's test. The results show that there was no statistically significant difference in the inhibition of S. mutans between 40% concentration of water soluble azadirachtin and chlorhexidine. This study concluded that 40% water soluble azadirachtin is as effective as 0.2% chlorhexidine mouthrinse in reducing the S. mutans count in dental plaque. Hence, a water soluble formulation of azadirachtin may provide the maximum benefit to mankind to prevent dental caries.

Inflammatory reactions in placental blood of Plasmodium falciparum-infected women and high concentrations of soluble E-selectin and a circulating P. falciparum protein in the cord sera

DEFF Research Database (Denmark)

Jakobsen, P H; Rasheed, F N; Bulmer, J N

1998-01-01

concentrations measured in the placenta. Markers of inflammatory reactions: IL-10, sIL-2R, sIL-4R, and soluble tumour necrosis factor receptor I (sTNF-RI) were found in high concentrations in the placenta, indicating that inflammatory reactions take place in the placenta which has been regarded...... as an immunoprivileged site. Concentrations of soluble vascular cell adhesion molecule-1 (sVCAM-1) and soluble intracellular adhesion molecule-1 (sICAM-1), potential adhesion receptors for malaria parasites, were associated with an active P. falciparum infection in the placenta although the associations did not reach...

Wheat germ cell-free expression: Two detergents with a low critical micelle concentration allow for production of soluble HCV membrane proteins.

Science.gov (United States)

Fogeron, Marie-Laure; Badillo, Aurélie; Jirasko, Vlastimil; Gouttenoire, Jérôme; Paul, David; Lancien, Loick; Moradpour, Darius; Bartenschlager, Ralf; Meier, Beat H; Penin, François; Böckmann, Anja

2015-01-01

Membrane proteins are notoriously difficult to express in a soluble form. Here, we use wheat germ cell-free expression in the presence of various detergents to produce the non-structural membrane proteins 2, 4B and 5A of the hepatitis C virus (HCV). We show that lauryl maltose neopentyl glycol (MNG-3) and dodecyl octaethylene glycol ether (C12E8) detergents can yield essentially soluble membrane proteins at detergent concentrations that do not inhibit the cell-free reaction. This finding can be explained by the low critical micelle concentration (CMC) of these detergents, which keeps the monomer concentrations low while at the same time providing the necessary excess of detergent concentration above CMC required for full target protein solubilization. We estimate that a tenfold excess of detergent micelles with respect to the protein concentration is sufficient for solubilization, a number that we propose as a guideline for detergent screening assays. Copyright © 2014 Elsevier Inc. All rights reserved.

Molecular Thermodynamic Modeling of Mixed Solvent Solubility

DEFF Research Database (Denmark)

Ellegaard, Martin Dela; Abildskov, Jens; O’Connell, John P.

2010-01-01

A method based on statistical mechanical fluctuation solution theory for composition derivatives of activity coefficients is employed for estimating dilute solubilities of 11 solid pharmaceutical solutes in nearly 70 mixed aqueous and nonaqueous solvent systems. The solvent mixtures range from...... nearly ideal to strongly nonideal. The database covers a temperature range from 293 to 323 K. Comparisons with available data and other existing solubility methods show that the method successfully describes a variety of observed mixed solvent solubility behaviors using solute−solvent parameters from...

Formation and filtration characteristics of solids generated in a high level liquid waste treatment process. Solids formation behavior from simulated high level liquid waste

International Nuclear Information System (INIS)

Kondo, Y.; Kubota, M.

1997-01-01

The solids formation behavior in a simulated high level liquid waste (HLLW) was experimentally examined, when the simulated HLLW was treated in the ordinary way of actual HLLW treatment process. Solids formation conditions and mechanism were closely discussed. The solids formation during a concentration step can be explained by considering the formation of zirconium phosphate, phosphomolybdic acid and precipitation of strontium and barium nitrates and their solubilities. For the solids formation during the denitration step, at least four courses were observed; formation of an undissolved material by a chemical reaction with each other of solute elements (zirconium, molybdenum, tellurium) precipitation by reduction (platinum group metals) formation of hydroxide or carbonate compounds (chromium, neodymium, iron, nickel, strontium, barium) and a physical adsorption to stable solid such as zirconium molybdate (nickel, strontium, barium). (author)

ISOLATION AND CHARACTERIZATION OF SOLUBLE POLYSACCHARIDES FROM CALAMAGROSTIS ANGUSTIFOLIA KOM

Directory of Open Access Journals (Sweden)

Xue-Fei Cao

2011-06-01

Full Text Available Sequential treatments of dewaxed Calamagrostis angustifolia Kom with water (60 ºC and 90 ºC, 70% ethanol, and 70% ethanol containing 0.2%, 1.0%, 2.0%, 4.0%, and 8.0% NaOH at a solid to liquid ratio of 1:25 (g/mL at 80 ºC for 3 h yielded 36.2% soluble polysaccharides of the dry dewaxed material. The eight polysaccharide fractions obtained were comparatively studied by sugar analysis, GPC, FT-IR, 1H and 13C-NMR, and 2D-NMR (HSQC spectroscopy. The results showed that the water-soluble polysaccharides might contain noticeable amounts of β-D-glucan, as well as some pectic substances and galactoarabinoxylan. 70% ethanol-soluble polysaccharide was mainly arabinogalactan. The five alkali-soluble hemicelluloses were mainly galactoarabinoxylans. The Ara/Xyl and Ara/Gal values of H5-H8 fractions decreased with the increment of NaOH concentration from 1.0% to 8.0%. Meanwhile, the molecular weights had a declining trend from ~60,000 to ~40,000 g/mol. The smaller sized and more branched polysaccharides tended to be extracted in the early stages under milder conditions, and the larger molecular sized and more linear hemicelluloses tended to be isolated under more highly alkaline conditions.

Influence of organic matter on the solubility of ThO2 and geochemical modeling

International Nuclear Information System (INIS)

Liu Dejun; Luo Tian; Maes, N.; Bruggeman, C.

2014-01-01

Thorium (IV) is widely considered in laboratory experiments as a suitable chemical analogue for long-lived tetravalent actinides. Th (IV) is redox-insensitive, as an analogue for U (IV) to study the influence of natural organic matter on the solubility. The solubility of crystalline ThO 2 (cr) has been measured under geochemical conditions representative for the Boom Clay using Real Boom Clay Water containing organic matter to assess its influence on the ThO 2 (cr) solubility. For the purpose of comparison, Aldrich Humic Acid was also investigated. Solubility measurements of ThO 2 (cr) were approached from under-saturation in an anaerobic glove box with a controlled Ar0.4%CO 2 atmosphere. Th concentration is determined after 30000 MWCO, 300000 MWCO, and 0.45 μm filtration to distinguish solid (0.45 μm), larger colloids (300000 MWCO), and small dissolved species(30000 MWCO). X-ray diffraction was carried out to investigate the transformation of ThO 2 (cr) phase during the contact with Boom Clay Water. In Synthetic Boom Clay Water (without organic matter) the concentrations of Th (IV) are 5 × l0 -ll mol/L, 4 × lO -10 mol/L, and 8 × lO -8 mol/L after 30000 MWCO, 300000 MWCO, and 0. 45 μm filtration, respectively. It indicated the existence of inorganic colloids in solution. The increase of the total Th solution concentration with increasing organic matter concentration revealed a complexation-like interaction between Th and organic matter. All the experimental data could be modeled by Tipping humic ion-binding model VI using a combination of solubility calculations and complexation reactions between Th (IV) and organic matter functional groups. Similar to the investigation of Eu 3+ solubility, the affinity of organic matter for Th was higher for Aldrich humic acid compared to Boom Clay organic matter. However, Boom Clay organic matter with different size had the similar complexation affinity with Th (IV). (authors)

Solubility limited radionuclide transport through geologic media

International Nuclear Information System (INIS)

Muraoka, Susumu; Iwamoto, Fumio; Pigford, T.H.

1980-11-01

Prior analyses for the migration of radionuclides neglect solubility limits of resolved radionuclide in geologic media. But actually some of the actinides may appear in chemical forms of very low solubility. In the present report we have proposed the migration model with no decay parents in which concentration of radionuclide is limited in concentration of solubility in ground water. In addition, the analytical solutions of the space-time-dependent concentration are presented in the case of step release, band release and exponential release. (author)

Solubility database for TILA-99

Energy Technology Data Exchange (ETDEWEB)

Vuorinen, U.; Carlsson, T. [VTT Chemical Technology, Espoo (Finland); Kulmala, S.; Hakanen, M. [Helsinki Univ. (Finland). Lab. of Radiochemistry; Ahonen, L. [Geological Survey of Finland, Espoo (Finland)

1998-11-01

The safety assessment of spent fuel disposal requires solubility values for several elements estimated in Finnish disposal conditions. In Finland four sites (Haestholmen, Kivetty, Olkiluoto and Romuvaara) are investigated for the disposal of spent fuel. Haestholmen and OLkiluoto are onshore sites, while Kivetty and Romuvaara are inland sites. Based on groundwater analysis and classification according to salinity at the planned disposal depth mainly fresh groundwater is encountered at Kivetty and Romuvaara, while brackish and saline water-types are met at Haestholmen and Olkiluoto. Very saline, almost brine-type water ({approx}70 g/l) has been found in the deepest parts of the investigated bedrock at one of the sites (Olkiluoto). The reference waters and conditions were chosen according to the water-types. The considered reference conditions incorporated both the near- and far-field, and both oxidizing and reducing conditions were considered. In the reference conditions, the changes in solubilities were also estimated as caused by possible variations in the pH, carbonate content and redox conditions. Uranium, which is the main component of spent fuel is dealt with in a separate report presenting the solubility of uranium and spent fuel dissolution. In this work the solubilities of all the other elements of concern (Am, Cu, Nb, Np, Pa, Pd, Pu, Ra, Se, Sn, Tc, Zr, Cm, Ni, Sr, Th, C, Cl, Cs, Fe, Ho, I, and Sm) in the safety assessment are considered. Some discussion on the corrosion of the spent fuel canister is also presented. For the estimation of solubilities of the elements in question, literature data was collected that mainly comprised experimentally measured concentrations. The sources used were spent fuel experiments, concentrations measured in solubility measurements, natural concentrations and concentrations from natural analogue sites (especially Palmottu and Hyrkkoelae in Finland) as well as the concentrations measured at the Finnish investigation sites

Solubility database for TILA-99

International Nuclear Information System (INIS)

Vuorinen, U.; Carlsson, T.; Kulmala, S.; Hakanen, M.

1998-11-01

The safety assessment of spent fuel disposal requires solubility values for several elements estimated in Finnish disposal conditions. In Finland four sites (Haestholmen, Kivetty, Olkiluoto and Romuvaara) are investigated for the disposal of spent fuel. Haestholmen and OLkiluoto are onshore sites, while Kivetty and Romuvaara are inland sites. Based on groundwater analysis and classification according to salinity at the planned disposal depth mainly fresh groundwater is encountered at Kivetty and Romuvaara, while brackish and saline water-types are met at Haestholmen and Olkiluoto. Very saline, almost brine-type water (∼70 g/l) has been found in the deepest parts of the investigated bedrock at one of the sites (Olkiluoto). The reference waters and conditions were chosen according to the water-types. The considered reference conditions incorporated both the near- and far-field, and both oxidizing and reducing conditions were considered. In the reference conditions, the changes in solubilities were also estimated as caused by possible variations in the pH, carbonate content and redox conditions. Uranium, which is the main component of spent fuel is dealt with in a separate report presenting the solubility of uranium and spent fuel dissolution. In this work the solubilities of all the other elements of concern (Am, Cu, Nb, Np, Pa, Pd, Pu, Ra, Se, Sn, Tc, Zr, Cm, Ni, Sr, Th, C, Cl, Cs, Fe, Ho, I, and Sm) in the safety assessment are considered. Some discussion on the corrosion of the spent fuel canister is also presented. For the estimation of solubilities of the elements in question, literature data was collected that mainly comprised experimentally measured concentrations. The sources used were spent fuel experiments, concentrations measured in solubility measurements, natural concentrations and concentrations from natural analogue sites (especially Palmottu and Hyrkkoelae in Finland) as well as the concentrations measured at the Finnish investigation sites. The

Influences of chia flour and the concentration of total solids on the characteristics of ‘dulce de leche’ from goat milk

Directory of Open Access Journals (Sweden)

Marcia Alves CHAVES

2018-03-01

Full Text Available Abstract A factorial categorical design totalling six treatments was applied to investigate the influence of the substitution of corn starch with whole and partially defatted chia flour under the technical characteristics (centesimal composition, instrumental analyses, and sensory evaluation and nutritional disorders (composition of fatty acids and index of the nutritional quality of the lipid fraction of ‘dulce de leche’ concentrated to 72 and 78 °B. The treatments with chia flour concentrated to 72 °B showed higher moisture content and lower compression force, and when the concentration range increased to 78 °B, the levels of total lipids amounted up to 1.40 times when compared to treatment with corn starch. The polyunsaturated fatty acids, particularly omega-3 and omega-6 levels, were higher in treatments with chia flour on both tracks of concentration, allowing a reduction in the atherogenic index and thrombogenic index effects and the n-6/n-3 ratio. The treatments of ‘dulce de leche’ with a lower concentration of soluble solids obtained greater acceptance and consumer purchase intention. The application of whole chia flour in small proportions and in the concentration of 72 °B was the most appropriate under the studied conditions, showing improvement in the nutritional quality and with good technical aspects of candy made with goat milk.

On solubility of perchloric (periodic) acid and α-cyanacetanmide in aqueous solutions at 25 deg C

International Nuclear Information System (INIS)

Omarova, R.A.; Balysbekov, S.M.; Erkasov, R.Sh.; Nikolenko, O.N.

1996-01-01

Acid-base interaction within perchloric (periodic) acid-α-cyanacetamide-water systems in studied by method of solubility under isothermal conditions at 25 deg C. Solubility regularities of crystalline α-cyanacetamide in perchloric and periodic acid solutions are determined, the concentration limits of formation of a new solid phase-tris(α-cyanacetamide) perchlorate within perchloric acid-α-cyanacetamide-water system are determined. The compound is identified by means of chemical and X-ray phase analyses, its density and melting temperature are determined. Iodic acid and α-cyanacetamide water solution base system is shown to belong to a simple eutonic type. 2 refs., 3 figs., 2 tabs

Calculation of solubility of salts in binary aqueous solutions

International Nuclear Information System (INIS)

Kolker, A.R.

1990-01-01

The possibility of theoretical calculation of solubility of some salts of the MX-type, where M - Na, K, Cs; X - F-I, as well as CsNO 3 and others forming no crystal hydrates in the solid phase, and the azeotropic composition in the water-HNO 3 system is studied. The calculational results of solubility are shown to depend very much on the values accepted for the standard free energies of component formation, melting heats and crystallization and on the difference in heat capacity of the melt and the solid phase

The effect of different concentrations of water soluble azadirachtin (neem metabolite on Streptococcus mutans compared with chlorhexidine

Directory of Open Access Journals (Sweden)

Amit R Kankariya

2016-01-01

Full Text Available Despite advances in the development of anticaries chemotherapy, the newer agents are unable to control the initiation of dental caries. Research and development of natural antibacterial agents that are safe for the host as well as specific for oral pathogens is awaited. Neem tree extracts have been used for thousands of years for maintaining overall well-being. Chewing neem sticks in the morning is the most common indigenous method of cleaning the mouth in rural population. This has generated the interest of the dentists for the use of neem for controlling dental diseases. Aims: This study aims to evaluate the quantitative and qualitative effect of different concentrations of water soluble azadirachtin (neem metabolite on Streptococcus mutans (S. mutans against chlorhexidine. Materials and Methods: Plaque was collected from 30 children aged 8-12 years reporting to the Department of Pediatric and Preventive Dentistry, Bharti Vidyapeeth Dental College, Pune and transported to the laboratory. After incubation of the plates the inhibitory zones were noted and the diameter of the zone of inhibition was measured and recorded to check the inhibition of growth of S. mutans. For testing the bacterial survival, the biofilms were prepared and colony forming units (CFU was enumerated using a digital colony counter. Statistical Analysis Used: Two-way analysis of variance (ANOVA and Tukey′s test. Results: The results show that there was no statistically significant difference in the inhibition of S. mutans between 40% concentration of water soluble azadirachtin and chlorhexidine. Conclusions: This study concluded that 40% water soluble azadirachtin is as effective as 0.2% chlorhexidine mouthrinse in reducing the S. mutans count in dental plaque. Hence, a water soluble formulation of azadirachtin may provide the maximum benefit to mankind to prevent dental caries.

Solubility of pllutonium in alkaline salt solutions

International Nuclear Information System (INIS)

Hobbs, D.T.; Edwards, T.B.

1993-01-01

Plutonium solubility data from several studies have been evaluated. For each data set, a predictive model has been developed where appropriate. In addition, a statistical model and corresponding prediction intervals for plutonium solubility as a quadratic function of the hydroxide concentration have been developed. Because of the wide range of solution compositions, the solubility of plutonium can vary by as much as three orders of magnitude for any given hydroxide concentration and still remain within the prediction interval. Any nuclear safety assessments that depend on the maximum amount of plutonium dissolved in alkaline salt solutions should use concentrations at least as great as the upper prediction limits developed in this study. To increase the confidence in the prediction model, it is recommended that additional solubility tests be conducted at low hydroxide concentrations and with all of the other solution components involved. To validate the model for application to actual waste solutions, it is recommended that the plutonium solubilities in actual waste solutions be determined and compared to the values predicted by the quadratic model

Hydrogen solubility in polycrystalline - and nonocrystalline niobium

International Nuclear Information System (INIS)

Ishikawa, T.T.; Silva, J.R.G. da

1981-01-01

Hydrogen solubility in polycrystalline and monocrystalline niobium was measured in the range 400 0 C to 1000 0 C at one atmosphere hydrogen partial pressure. The experimental technique consists of saturation of the solvent metal with hydrogen, followed by quenching and analysis of the solid solution. It is presented solubility curves versus reciprocal of the absolute doping temperature, associated with their thermodynamical equation. (Author) [pt

Crystalline Ethylene Oxide and Propylene Oxide Triblock Copolymer Solid Dispersion Enhance Solubility, Stability and Promoting Time- Controllable Release of Curcumin.

Science.gov (United States)

Alves, Thais F R; das Neves Lopes, Franciely C C; Rebelo, Marcia A; Souza, Juliana F; da Silva Pontes, Katiusca; Santos, Carolina; Severino, Patricia; Junior, Jose M O; Komatsu, Daniel; Chaud, Marco V

2018-01-01

The design and development of an effective medicine are, however, often faced with a number of challenges. One of them is the close relationship of drug's bioavailability with solubility, dissolution rate and permeability. The use of curcumin's (CUR) therapeutic potential is limited by its poor water solubility and low chemical stability. The purpose was to evaluate the effect of polymer and solid dispersion (SD) preparation techniques to enhance the aqueous solubility, dissolution rate and stability of the CUR. The recent patents on curcumin SD were reported as (i) curcumin with polyvinylpyrrolidone (CN20071 32500 20071214, WO2006022012 and CN20151414227 20150715), (ii) curcumin-zinc/polyvinylpyrrolidone (CN20151414227 20150715), (iii) curcumin-poloxamer 188 (CN2008171177 20080605), (iv) curcumin SD prepared by melting method (CN20161626746-20160801). SD obtained by co-preciptation or microwave fusion and the physical mixture of CUR with Poloxamer-407 (P-407), Hydroxypropylmetylcellulose-K4M (HPMC K4M) and Polyvinylpyrrolidone-K30 (PVP-K30) were prepared at the ratios of 1:2; 1:1 and 2:1. The samples were evaluated by solubility, stability, dissolution rate and characterized by SEM, PXRD, DSC and FTIR. The solubility, stability (pH 7.0) and dissolution rate were significantly greater for SD (CUR:P-407 1:2). The PXRD,SEM and DSC indicated a change in the crystalline state of CUR. The enhancement of solubility was dependent on a combination of factors including the weight ratio, preparation techniques and carrier properties. The drug release data fitted well with the Weibull equation, indicating that the drug release was controlled by diffusion, polymer relaxation and erosion occurring simultaneously. Thus, these SDs, specifically CUR:P-407 1:2 w/w, can overcome the barriers of poor bioavailability to reap many beneficial properties. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Solubility of hydrogen isotopes in stressed hydride-forming metals

International Nuclear Information System (INIS)

Coleman, C.E.; Ambler, J.F.R.

1983-01-01

Components made from hydride-forming metals can be brittle when particles of hydride are present. The solid solubility limit of hydrogen in these metals needs to be known so that fracture resistance can be properly assessed. Stress affects the solubility of hydrogen in metals. As hydrogen dissolves the metal volume increases, an applied hydrostatic tensile stress supplies work to increase the solubility. Precipitation of hydrides increases the volume further. A hydrostatic tensile stress promotes the formation of hydrides and tends to reduce the terminal solubility. For materials containing hydrogen in solution in equilibrium with hydrides, the effect of stress on the terminal solubility is given. Hydrogen migrates up tensile stress gradients because of the effect of stress on the solubility and solubility limit. Consequently, hydrogen concentrates at flaws. When hydrides are present in the metal matrix, those remote from the flaw tip will preferentially dissolve in favor of those precipitated at the flaw. If the stress is large enough, at some critical condition the hydrides at the flaw will crack. This is delayed hydrogen cracking. Notched and fatigue-cracked cantilever beam specimens (6) (38 x 4 x 3 mm) were machined from the circumferential direction of several cold-worked Zr-2.5 at. % Nb pressure tubes. The chemical compositions had the ranges (in atomic %) Nb - 2.5 to 2.7; O - 0.58 to 0.71; H - 0.018 to 0.18. The effect of test temperature is for a specimen containing 0.13 at. % protium and 0.29 at .% deuterium. Between 505 K and 530 K was less than 1 hr, between 530 K and 537 K it increased to 25.8 h, while at 538 K no cracking was observed up to the 54 h

Dissolved-solids sources, loads, yields, and concentrations in streams of the conterminous United States

Science.gov (United States)

Anning, David W.; Flynn, Marilyn E.

2014-01-01

Recent studies have shown that excessive dissolved-solids concentrations in water can have adverse effects on the environment and on agricultural, domestic, municipal, and industrial water users. Such effects motivated the U.S. Geological Survey’s National Water Quality Assessment Program to develop a SPAtially-Referenced Regression on Watershed Attributes (SPARROW) model that has improved the understanding of sources, loads, yields, and concentrations of dissolved solids in streams of the conterminous United States.

REVIEW ON SPRAY DRIED SOLID DISPERSION

OpenAIRE

Zambre Radhika Ashok, Dr. Shendge R.S, Narode Pravin Ravindra, Sonawane Swapnil Prakash

2018-01-01

The drug solubility is the most challenging aspect for the formulation development. The poorly soluble drug has poor dissolution and absorption of drug. The low aqueous solubility of drug is required to formulate the drug into more soluble and hence bioavailable drug product. The different technique is being used to enhance the solubility of poorly water soluble drugs. Spray dried solid dispersion of drug is one of the most widely used technology to enhance the solubility of the poorly water ...

Some physicochemical aspects of water-soluble mineral flotation.

Science.gov (United States)

Wu, Zhijian; Wang, Xuming; Liu, Haining; Zhang, Huifang; Miller, Jan D

2016-09-01

Some physicochemical aspects of water-soluble mineral flotation including hydration phenomena, associations and interactions between collectors, air bubbles, and water-soluble mineral particles are presented. Flotation carried out in saturated salt solutions, and a wide range of collector concentrations for effective flotation of different salts are two basic aspects of water-soluble mineral flotation. Hydration of salt ions, mineral particle surfaces, collector molecules or ions, and collector aggregates play an important role in water-soluble mineral flotation. The adsorption of collectors onto bubble surfaces is suggested to be the precondition for the association of mineral particles with bubbles. The association of collectors with water-soluble minerals is a complicated process, which may include the adsorption of collector molecules or ions onto such surfaces, and/or the attachment of collector precipitates or crystals onto the mineral surfaces. The interactions between the collectors and the minerals include electrostatic and hydrophobic interactions, hydrogen bonding, and specific interactions, with electrostatic and hydrophobic interactions being the common mechanisms. For the association of ionic collectors with minerals with an opposite charge, electrostatic and hydrophobic interactions could have a synergistic effect, with the hydrophobic interactions between the hydrophobic groups of the previously associated collectors and the hydrophobic groups of oncoming collectors being an important attractive force. Association between solid particles and air bubbles is the key to froth flotation, which is affected by hydrophobicity of the mineral particle surfaces, surface charges of mineral particles and bubbles, mineral particle size and shape, temperature, bubble size, etc. The use of a collector together with a frother and the use of mixed surfactants as collectors are suggested to improve flotation. Copyright © 2016 Elsevier B.V. All rights reserved.

Dietary fiber content influences soluble carbohydrate levels in ruminal fluids.

Science.gov (United States)

Pinder, R S; Patterson, J A; O'Bryan, C A; Crandall, P G; Ricke, S C

2012-01-01

The soluble carbohydrate concentration of ruminal fluid, as affected by dietary forage content (DFC) and/or ruminally undegradable intake protein content (UIPC), was determined. Four ruminally cannulated steers, in a 4 × 4 Latin square design, were offered diets containing high (75 % of DM) or low (25 % of DM) DFC and high (6 % of DM) or low (5 % of DM) UIPC, in a 2 × 2 factorial arrangement. Zinc-treated SBM was the primary UIP source. Soluble hexose concentration (145.1 μM) in ruminal fluid (RF) of steers fed low DFC diets exhibited a higher trend (P = 0.08) than that (124.5 μM) of steers fed high DFC diets. UIPC did not modulate (P = 0.54) ruminal soluble hexose concentrations. Regardless of diet, soluble hexose concentration declined immediately after feeding and did not rise until 3 h after feeding (P ruminal fluid could not be determined. However, unsubstituted xylose and arabinose were excluded. These data indicate that: (i) soluble carbohydrate concentrations remain in ruminal fluid during digestion and fermentation; (ii) slight diurnal changes began after feeding; (iii) DFC influences the soluble carbohydrate concentration in RF; and (iv) UIPC of these diets does not affect the soluble carbohydrate concentration of RF.

Soluble Non-ammonia Nitrogen in Ruminal and Omasal Digesta of Korean Native Steers Supplemented with Soluble Proteins

Directory of Open Access Journals (Sweden)

C. W. Choi

2012-09-01

Full Text Available An experiment was conducted to study the effect of soluble protein supplements on concentration of soluble non-ammonia nitrogen (SNAN in the liquid phase of ruminal (RD and omasal digesta (OD of Korean native steers, and to investigate diurnal pattern in SNAN concentration in RD and OD. Three ruminally cannulated Korean native steers in a 3×3 Latin square design consumed a basal diet of rice straw and corn-based concentrate (control, and that supplemented (kg/d DM basis with intact casein (0.24; IC or acid hydrolyzed casein (0.46; AHC. Ruminal digesta was sampled using a vacuum pump, whereas OD was collected using an omasal sampling system at 2.0 h intervals after a morning feeding. The SNAN fractions (free amino acid (AA, peptide and soluble protein in RD and OD were assessed using the ninhydrin assay. Concentrations of free AA and total SNAN in RD were significantly (p<0.05 lower than those in OD. Although free AA concentration was relatively high, mean peptide was quantitatively the most important fraction of total SNAN in both RD and OD, indicating that degradation of peptide to AA rather than hydrolysis of soluble protein to peptide or deamination may be the most limiting step in rumen proteolysis of Korean native steers. Diurnal variation in peptide concentration in OD for the soluble protein supplemented diets during the feeding cycle peaked 2 h post-feeding and decreased thereafter whereas that for the control was relatively constant during the entire feeding cycle. Diurnal variation in peptide concentration was rather similar between RD and OD.

Anti-Inflammatory Effects of Novel Standardized Solid Lipid Curcumin Formulations.

Science.gov (United States)

Nahar, Pragati P; Slitt, Angela L; Seeram, Navindra P

2015-07-01

Inflammation and the presence of pro-inflammatory cytokines are associated with numerous chronic diseases such as type-2 diabetes mellitus, cardiovascular disease, Alzheimer's disease, and cancer. An overwhelming amount of data indicates that curcumin, a polyphenol obtained from the Indian spice turmeric, Curcuma longa, is a potential chemopreventive agent for treating certain cancers and other chronic inflammatory diseases. However, the low bioavailability of curcumin, partly due to its low solubility and stability in the digestive tract, limits its therapeutic applications. Recent studies have demonstrated increased bioavailability and health-promoting effects of a novel solid lipid particle formulation of curcumin (Curcumin SLCP, Longvida(®)). The goal of this study was to evaluate the aqueous solubility and in vitro anti-inflammatory effects of solid lipid curcumin particle (SLCP) formulations using lipopolysaccharide (LPS)-stimulated RAW 264.7 cultured murine macrophages. SLCPs treatment significantly decreased nitric oxide (NO) and prostaglandin-E2 (PGE2) levels at concentrations ranging from 10 to 50 μg/mL, and reduced interleukin-6 (IL-6) levels in a concentration-dependent manner. Transient transfection experiments using a nuclear factor-kappa B (NF-κB) reporter construct indicate that SLCPs significantly inhibit the transcriptional activity of NF-κB in macrophages. Taken together, these results show that in RAW 264.7 murine macrophages, SLCPs have improved solubility over unformulated curcumin, and significantly decrease the LPS-induced pro-inflammatory mediators NO, PGE2, and IL-6 by inhibiting the activation of NF-κB.

Water-soluble dietary fibers and cardiovascular disease.

Science.gov (United States)

Theuwissen, Elke; Mensink, Ronald P

2008-05-23

One well-established way to reduce the risk of developing cardiovascular disease (CVD) is to lower serum LDL cholesterol levels by reducing saturated fat intake. However, the importance of other dietary approaches, such as increasing the intake of water-soluble dietary fibers is increasingly recognized. Well-controlled intervention studies have now shown that four major water-soluble fiber types-beta-glucan, psyllium, pectin and guar gum-effectively lower serum LDL cholesterol concentrations, without affecting HDL cholesterol or triacylglycerol concentrations. It is estimated that for each additional gram of water-soluble fiber in the diet serum total and LDL cholesterol concentrations decrease by -0.028 mmol/L and -0.029 mmol/L, respectively. Despite large differences in molecular structure, no major differences existed between the different types of water-soluble fiber, suggesting a common underlying mechanism. In this respect, it is most likely that water-soluble fibers lower the (re)absorption of in particular bile acids. As a result hepatic conversion of cholesterol into bile acids increases, which will ultimately lead to increased LDL uptake by the liver. Additionally, epidemiological studies suggest that a diet high in water-soluble fiber is inversely associated with the risk of CVD. These findings underlie current dietary recommendations to increase water-soluble fiber intake.

Decreased concentrations of soluble interleukin-1 receptor accessory protein levels in the peritoneal fluid of women with endometriosis.

Science.gov (United States)

Michaud, Nadège; Al-Akoum, Mahéra; Gagnon, Geneviève; Girard, Karine; Blanchet, Pierre; Rousseau, Julie Anne; Akoum, Ali

2011-12-01

Interleukin 1 (IL1) may play an important role in endometriosis-associated pelvic inflammation, and natural specific inhibitors, including soluble IL1 receptor accessory protein (sIL1RAcP) and soluble IL1 receptor type 2 (sIL1R2), are critical for counterbalancing the pleiotropic effects of IL1. The objective of this study was to evaluate the levels of sIL1RAcP, together with those of sIL1R2 and IL1β, in the peritoneal fluid of women with and without endometriosis. Peritoneal fluid samples were obtained at laparoscopy and assessed by ELISA. sIL1RAcP concentrations were reduced in endometriosis stages I-II and III-IV. sIL1R2 concentrations were decreased, and those of IL1β were significantly increased in endometriosis stages I-II. sIL1RAcP and sIL1R2 concentrations were significantly decreased in the secretory phase of the menstrual cycle, and IL1β concentrations were elevated in the proliferative and the secretory phases. sIL1RAcP and sIL1R2 concentrations were reduced in women with endometriosis who were infertile, fertile, suffering from pelvic pain or pain-free. However, IL1β concentrations were significantly reduced in women with endometriosis who were infertile or had pelvic pain. These changes may exacerbate the local peritoneal inflammatory reaction observed in women with endometriosis and contribute to endometriosis pathophysiology and the major symptoms of this disease. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

Nitrogen solubility in the deep mantle and the origin of Earth's primordial nitrogen budget

Science.gov (United States)

Yoshioka, Takahiro; Wiedenbeck, Michael; Shcheka, Svyatoslav; Keppler, Hans

2018-04-01

The solubility of nitrogen in the major minerals of the Earth's transition zone and lower mantle (wadsleyite, ringwoodite, bridgmanite, and Ca-silicate perovskite) coexisting with a reduced, nitrogen-rich fluid phase was measured. Experiments were carried out in multi-anvil presses at 14 to 24 GPa and 1100 to 1800 °C close to the Fe-FeO buffer. Starting materials were enriched in 15N and the nitrogen concentrations in run products were measured by secondary ion mass spectrometry. Observed nitrogen (15N) solubilities in wadsleyite and ringwoodite typically range from 10 to 250 μg/g and strongly increase with temperature. Nitrogen solubility in bridgmanite is about 20 μg/g, while Ca-silicate perovskite incorporates about 30 μg/g under comparable conditions. Partition coefficients of nitrogen derived from coexisting phases are DNwadsleyite/olivine = 5.1 ± 2.1, DNringwoodite/wadsleyite = 0.49 ± 0.29, and DNbridgmanite/ringwoodite = 0.24 (+ 0.30 / - 0.19). Nitrogen solubility in the solid, iron-rich metal phase coexisting with the silicates was also measured and reached a maximum of nearly 1 wt.% 15N at 23 GPa and 1400 °C. These data yield a partition coefficient of nitrogen between iron metal and bridgmanite of DNmetal/bridgmanite ∼ 98, implying that in a lower mantle containing about 1% of iron metal, about half of the nitrogen still resides in the silicates. The high nitrogen solubility in wadsleyite and ringwoodite may be responsible for the low nitrogen concentrations often observed in ultradeep diamonds from the transition zone. Overall, the solubility data suggest that the transition zone and the lower mantle have the capacity to store at least 33 times the mass of nitrogen presently residing in the atmosphere. By combining the nitrogen solubility data in minerals with data on nitrogen solubility in silicate melts, mineral/melt partition coefficients of nitrogen can be estimated, from which the behavior of nitrogen during magma ocean crystallization can

Solubility and phase behaviors of DGA compounds in supercritical CO2

International Nuclear Information System (INIS)

Li Jia; Meng Qingyang

2010-01-01

Solubility and phase behaviors of DGA compounds in supercritical CO 2 (Sc-CO 2 ) was investigated. The results indicated: The dissolving ability of these six DGA compounds in Sc-CO 2 is TEDGA> TBDGA>THDGA>TODGA>TDDGA >TDdDGA; The solubility of DGA in Sc-CO 2 increase with increasing density of CO 2 , pressure and δ CO 2 ; The structure of DGA compounds is the mainly factor effected on solubility of DGA compounds in Sc-CO 2 , and the effect of hydrophobicity on solubility is much smaller than that of DGA's structure. In Sc-CO 2 , TDDGA and TDdDGA can't form the available extraction system; TEDGA and TBDGA are useful for extraction of solid powder; TODGA and THDGA are both useful for extraction of solid powder and solution contained some kind of actinide metal. (authors)

Application of Acoustic and Optic Methods for Estimating Suspended-Solids Concentrations in the St. Lucie River Estuary, Florida

Science.gov (United States)

Patino, Eduardo; Byrne, Michael J.

2004-01-01

Acoustic and optic methods were applied to estimate suspended-solids concentrations in the St. Lucie River Estuary, southeastern Florida. Acoustic Doppler velocity meters were installed at the North Fork, Speedy Point, and Steele Point sites within the estuary. These sites provide varying flow, salinity, water-quality, and channel cross-sectional characteristics. The monitoring site at Steele Point was not used in the analyses because repeated instrument relocations (due to bridge construction) prevented a sufficient number of samples from being collected at the various locations. Acoustic and optic instruments were installed to collect water velocity, acoustic backscatter strength (ABS), and turbidity data that were used to assess the feasibility of estimating suspended-solids concentrations in the estuary. Other data collected at the monitoring sites include tidal stage, salinity, temperature, and periodic discharge measurements. Regression analyses were used to determine the relations of suspended-solids concentration to ABS and suspended-solids concentration to turbidity at the North Fork and Speedy Point sites. For samples used in regression analyses, measured suspended-solids concentrations at the North Fork and Speedy Point sites ranged from 3 to 37 milligrams per liter, and organic content ranged from 50 to 83 percent. Corresponding salinity for these samples ranged from 0.12 to 22.7 parts per thousand, and corresponding temperature ranged from 19.4 to 31.8 ?C. Relations determined using this technique are site specific and only describe suspended-solids concentrations at locations where data were collected. The suspended-solids concentration to ABS relation resulted in correlation coefficients of 0.78 and 0.63 at the North Fork and Speedy Point sites, respectively. The suspended-solids concentration to turbidity relation resulted in correlation coefficients of 0.73 and 0.89 at the North Fork and Speedy Point sites, respectively. The adequacy of the

Determination and assessment of the concentration limits to be used in SR-Can

Energy Technology Data Exchange (ETDEWEB)

Duro, L; Grive, M; Cera, E; Gaona, X; Domenech, C; Bruno, J [Enviros Spain S.L., Barcelona (Spain)

2006-12-15

This report presents the results for solubility limit calculations for the SR-Can assessment. It has been organized into five chapters that constitute the core of the report, supported by several appendices containing additional and supporting information. The updated thermodynamic database used to conduct the solubility calculations has been issued as a separate report. The near field system for which the concentration limits of the radionuclides are assessed and the scenarios selected by SKB to calculate the solubility limits are thoroughly described. Several sources of information have been used to support the calculated solubility limits. In particular results from selected spent fuel dissolution experiments and natural analogue data are discussed to introduce the proper perspective to the results from the thermodynamic calculations. In addition, the main conceptual and numerical uncertainties associated to the assessment of the concentration limits of each element are numerically evaluated and discussed. Equilibrium calculations have been conducted to select the solubility limiting solid phase for each element. Furthermore a sensitivity analysis of parameters of interest for each element is presented and the impact of the uncertainties identified on the solubility of each element quantified. The results are presented in a series of tables containing the calculated solubility for each radionuclide under the reference conditions. Finally concentration limits that are recommended result from the expert judgement built-up around the various sources of information together with the quantification of radionuclide solubility data and their associated uncertainties. The results are compared to previous solubility limits determination performed by SKB in SR 97, as well as the recommended values from other HLNW management organisations.

Determination and assessment of the concentration limits to be used in SR-Can

International Nuclear Information System (INIS)

Duro, L.; Grive, M.; Cera, E.; Gaona, X.; Domenech, C.; Bruno, J.

2006-12-01

This report presents the results for solubility limit calculations for the SR-Can assessment. It has been organized into five chapters that constitute the core of the report, supported by several appendices containing additional and supporting information. The updated thermodynamic database used to conduct the solubility calculations has been issued as a separate report. The near field system for which the concentration limits of the radionuclides are assessed and the scenarios selected by SKB to calculate the solubility limits are thoroughly described. Several sources of information have been used to support the calculated solubility limits. In particular results from selected spent fuel dissolution experiments and natural analogue data are discussed to introduce the proper perspective to the results from the thermodynamic calculations. In addition, the main conceptual and numerical uncertainties associated to the assessment of the concentration limits of each element are numerically evaluated and discussed. Equilibrium calculations have been conducted to select the solubility limiting solid phase for each element. Furthermore a sensitivity analysis of parameters of interest for each element is presented and the impact of the uncertainties identified on the solubility of each element quantified. The results are presented in a series of tables containing the calculated solubility for each radionuclide under the reference conditions. Finally concentration limits that are recommended result from the expert judgement built-up around the various sources of information together with the quantification of radionuclide solubility data and their associated uncertainties. The results are compared to previous solubility limits determination performed by SKB in SR 97, as well as the recommended values from other HLNW management organisations

The relationship between growth and soluble sugar concentration of Aloe vera plants grown under three levels of irradiance

Energy Technology Data Exchange (ETDEWEB)

Paez, A.; Gebre, G.M.; Tschaplinski, T.J. (Universidad del Zulia (Venezuela))

1994-06-01

The CAM plant Aloe vera was vegetatively propagated and grown under three irradiances: full sun, partial and deep shade (30% and 10% of ambient light, respectively) to determine the effect on growth, biomass allocation, and sugar concentration. After one year, the plants were harvested to determine final dry weight and the sugar concentration of the leaf mucilaginous gel. Plants grown under full sun produced twice the total dry weight of those grown under partial shade, with the difference equally partitioned between the shoot and root. Plants grown under full sun also produced thicker leaves, and more numerous and large auxiliary shoots. The dry weight of plants grown under deep shade was 8.6% that of plants grown under full sun, which was directly proportional to the irradiance received. Partial shade increased the number and length of leaves produced on the primary shoot, but the allocation of carbon to roots was the lowest of all treatments. Partial shade reduced the total sugar concentration of the leaf gel matrix to 34% that of plants under full sun, due to reductions in all sugars measured. Glucose was the most abundant soluble sugar, with its relative contribution to the total pool increasing under shade. In summary, the proportional effects of partial shading were greater on soluble sugar concentrations than on the total plant biomass produced.

JUICE EXTRACTION FOR TOTAL SOLUBLE SOLIDS CONTENT DETERMINATION IN MELON

Directory of Open Access Journals (Sweden)

Paulo Sérgio Lima e Silva

2006-01-01

Full Text Available The total soluble solids content (TSSC shows high positive correlation with sugars content, and therefore is generally accepted as an important quality trait of fruits. In melon, this evaluation is usually done by grinding a slice of the fruit's pulp in a household food processor, straining the ground material and then proceeding the TSSC determination in the resulting juice. This evaluation is labor-intensive and takes a long time to complete. An alternative process was delineated for obtaining the juice: the pulp of the fruit slice would be transversally cut one or more times, and longitudinally pressed by hand to obtain the juice. The objective of this work was to compare processes for obtaining juice to evaluate TSSC in melons. Fifty, 15, and 15 fruits of the Galia, Yellow, and Cantaloupe type melons were evaluated, respectively. Each fruit was considered as a block, and was longitudinally split into six fractions with similar sizes, which corresponded to the plots. The following treatments were evaluated: fraction without cuts, fractions with one, three, five, or seven transversal cuts, and the fraction treated by the conventional process. It was concluded that the procedure by which the melon slices of Galia, Yellow and Cantaloupe types are pressed for obtaining the juice to evaluate TSSC can overestimate this content. This would probably be due to the fact that the most internal section of the mesocarp presents greater TSSC than the portions closer to the epicarp.

End-Member Formulation of Solid Solutions and Reactive Transport

Energy Technology Data Exchange (ETDEWEB)

Lichtner, Peter C. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2015-09-01

A model for incorporating solid solutions into reactive transport equations is presented based on an end-member representation. Reactive transport equations are solved directly for the composition and bulk concentration of the solid solution. Reactions of a solid solution with an aqueous solution are formulated in terms of an overall stoichiometric reaction corresponding to a time-varying composition and exchange reactions, equivalent to reaction end-members. Reaction rates are treated kinetically using a transition state rate law for the overall reaction and a pseudo-kinetic rate law for exchange reactions. The composition of the solid solution at the onset of precipitation is assumed to correspond to the least soluble composition, equivalent to the composition at equilibrium. The stoichiometric saturation determines if the solid solution is super-saturated with respect to the aqueous solution. The method is implemented for a simple prototype batch reactor using Mathematica for a binary solid solution. Finally, the sensitivity of the results on the kinetic rate constant for a binary solid solution is investigated for reaction of an initially stoichiometric solid phase with an undersaturated aqueous solution.

An Introduction to the Understanding of Solubility.

Science.gov (United States)

Letcher, Trevor M.; Battino, Rubin

2001-01-01

Explores different solubility processes and related issues, including the second law of thermodynamics and ideal mixtures, real liquids, intermolecular forces, and solids in liquids or gases in liquids. (Contains 22 references.) (ASK)

Enhanced bioavailability of sirolimus via preparation of solid dispersion nanoparticles using a supercritical antisolvent process

Directory of Open Access Journals (Sweden)

Kim MS

2011-11-01

Full Text Available Min-Soo Kim1, Jeong-Soo Kim1, Hee Jun Park1, Won Kyung Cho1,3, Kwang-Ho Cha1,3, Sung-Joo Hwang2,31College of Pharmacy, Chungnam National University, Daejeon, Republic of Korea, 2College of Pharmacy, 3Yonsei Institute of Pharmaceutical Sciences, Yonsei University, Incheon, Republic of KoreaBackground: The aim of this study was to improve the physicochemical properties and bioavailability of poorly water-soluble sirolimus via preparation of a solid dispersion of nanoparticles using a supercritical antisolvent (SAS process.Methods: First, excipients for enhancing the stability and solubility of sirolimus were screened. Second, using the SAS process, solid dispersions of sirolimus-polyvinylpyrrolidone (PVP K30 nanoparticles were prepared with or without surfactants such as sodium lauryl sulfate (SLS, tocopheryl propylene glycol succinate, Sucroester 15, Gelucire 50/13, and Myrj 52. A mean particle size of approximately 250 nm was obtained for PVP K30-sirolimus nanoparticles. Solid state characterization, kinetic solubility, powder dissolution, stability, and pharmacokinetics were analyzed in rats.Results: X-ray diffraction, differential scanning calorimetry, and high-pressure liquid chromatography indicated that sirolimus existed in an anhydrous amorphous form within a solid dispersion of nanoparticles and that no degradation occurred after SAS processing. The improved supersaturation and dissolution of sirolimus as a solid dispersion of nanoparticles appeared to be well correlated with enhanced bioavailability of oral sirolimus in rats. With oral administration of a solid dispersion of PVP K30-SLS-sirolimus nanoparticles, the peak concentration and AUC0→12h of sirolimus were increased by approximately 18.3-fold and 15.2-fold, respectively.Conclusion: The results of this study suggest that preparation of PVP K30-sirolimus-surfactant nanoparticles using the SAS process may be a promising approach for improving the bioavailability of sirolimus

Solubility of chromium (III) oxide and metal chromates: development of MULTEQ models

International Nuclear Information System (INIS)

Dickinson, Shirley; Henshaw, Jim; Bachet Martin; Hussey, Dennis; Marks, Chuck; Tremaine, Peter; Eaker, Richard

2012-09-01

High-temperature solubility predictions for metal oxide systems are important for the understanding of corrosion processes, corrosion product behaviour and activity transport in PWR coolant systems. In the current work, literature data on chromium oxide and iron chromium solubility measurement have been used to derive equilibrium constant expressions for dissolution and hydrolysis reactions which have been incorporated in the latest revision of the EPRI MULTEQ database. Predicting the stable chromium phases in a PWR is important as these constitute the compact inner oxide layer that forms on most ex-core alloys used in this system. Likewise understanding the chromium chemistry is necessary for rationalising high chromium content crud that has been observed on several plant fuel pins. Chromium (III) oxide solubility measurements have shown that the equilibrium solid phase under hydrothermal conditions is CrOOH rather than Cr 2 O 3 . Expressions for the solubility product of this solid and the equilibrium constant for the 4. Cr (III) hydrolysis reaction Cr (OH) 3 (aq) + H 2 O = Cr (OH) 4 - + H + have been derived by fitting to the experimental solubility data in neutral to alkaline solution. The equilibrium constant for the 3rd hydrolysis reaction Cr (OH) 2 + +H 2 O = Cr (OH) 3 (aq) + H + has been revised for consistency with literature estimates of the hydrolysis constants at 298 K. There are insufficient high-quality solubility data at low pH to derive the lower hydrolysis constants so the existing MULTEQ entries, based on thermodynamic estimations, have been retained. This revised model gave reasonable agreement with the available data in acidic solution. A revised expression for the Cr 2 O 3 solubility product was derived from measurements of Fe concentrations produced from FeCr 2 O 4 dissolution, and this was used to obtain a consistent solubility product expression for FeCr 2 O 4 . The resulting model predicts that FeCr 2 O 4 would be unstable at temperatures

Physicochemical characterization and dissolution enhancement of loratadine by solid dispersion technique

International Nuclear Information System (INIS)

Bandari, Suresh; Jadav, Subash; Eedara, Basanth Babu; Jukanti, Raju; Veerareddy, Prabhakar Reddy

2013-01-01

The purpose of this investigation was to enhance the dissolution rate of loratadine using polyethylene glycol 6000 (PEG) solid dispersions (SDs). The solubility behavior of loratadine in the presence of polyethylene glycol 4000 and polyethylene glycol 6000 in water showed linear increase with increasing concentrations of PEG, indicating A L type solubility diagrams. SDs of loratadine with PEG 6000 were prepared at 1 : 1, 1 : 3, 1 : 5, 1 : 7 and 1 : 9 ratios by the solvent evaporation method. Solid dispersions were characterized for drug content, dissolution behavior and for physicochemical characteristics. The dissolution rate of loratadine was enhanced rapidly with increasing concentrations of PEG 6000 in SDs. Fourier transform infrared (FTIR) studies showed the stability of loratadine and the absence of a well-defined loratadine - PEG 6000 interaction. Differential scanning calorimetry (DSC) and X-ray powder diffractometry (XRD) studies revealed the amorphous state of loratadine in SDs of loratadine with PEG 6000 which was further confirmed from scanning electron microscopy (SEM) studies. The flow properties of the blend, physical characteristics and disintegration time of the tablets formulated indicated that PEG 6000 SD can be used to formulate fast release loratadine tablets

Physicochemical characterization and dissolution enhancement of loratadine by solid dispersion technique

Energy Technology Data Exchange (ETDEWEB)

Bandari, Suresh; Jadav, Subash; Eedara, Basanth Babu; Jukanti, Raju; Veerareddy, Prabhakar Reddy [St. Peter’s Institute of Pharmaceutical Sciences, Warangal (India)

2013-01-15

The purpose of this investigation was to enhance the dissolution rate of loratadine using polyethylene glycol 6000 (PEG) solid dispersions (SDs). The solubility behavior of loratadine in the presence of polyethylene glycol 4000 and polyethylene glycol 6000 in water showed linear increase with increasing concentrations of PEG, indicating A{sub L} type solubility diagrams. SDs of loratadine with PEG 6000 were prepared at 1 : 1, 1 : 3, 1 : 5, 1 : 7 and 1 : 9 ratios by the solvent evaporation method. Solid dispersions were characterized for drug content, dissolution behavior and for physicochemical characteristics. The dissolution rate of loratadine was enhanced rapidly with increasing concentrations of PEG 6000 in SDs. Fourier transform infrared (FTIR) studies showed the stability of loratadine and the absence of a well-defined loratadine - PEG 6000 interaction. Differential scanning calorimetry (DSC) and X-ray powder diffractometry (XRD) studies revealed the amorphous state of loratadine in SDs of loratadine with PEG 6000 which was further confirmed from scanning electron microscopy (SEM) studies. The flow properties of the blend, physical characteristics and disintegration time of the tablets formulated indicated that PEG 6000 SD can be used to formulate fast release loratadine tablets.

Sodium tetraphenylborate solubility and dissolution rates

International Nuclear Information System (INIS)

Barnes, M.J.; Peterson, R.A.; Swingle, R.F.; Reeves, C.T.

1995-01-01

The rate of solid sodium tetraphenylborate (NaTPB) dissolution in In-Tank Precipitation salt solutions has been experimentally determined. The data indicates that the dissolution rate of solid NaTPB is a minor contributor the lag time experienced in the 1983 Salt Decontamination Demonstration Test and should not be considered as the rate determining step. Current analytical models for predicting the time to reach the composite lower flammability limit assume that the lag time is not more than 6 hours, and the data supports this assumption (i.e., dissolution by itself requires much less than 6 hours). The data suggests that another step--such as mass transport, the reaction of a benzene precursor or the mixing behavior--is the rate determining factor for benzene release to the vapor space in Tank 48H. In addition, preliminary results from this program show that the degree of agitation employed is not a significant parameter in determining the rate of NaTPB dissolution. As a result of this study, an improved equation for predicting equilibrium tetraphenylborate solubility with respect to temperature and sodium ion concentration has been determined

Study on Mixed Solvency Concept in Formulation Development of Aqueous Injection of Poorly Water Soluble Drug

Directory of Open Access Journals (Sweden)

Shailendra Singh Solanki

2013-01-01

Full Text Available In the present investigation, mixed-solvency approach has been applied for the enhancement of aqueous solubility of a poorly water- soluble drug, zaltoprofen (selected as a model drug, by making blends (keeping total concentrations 40% w/v, constant of selected water-soluble substances from among the hydrotropes (urea, sodium benzoate, sodium citrate, nicotinamide; water-soluble solids (PEG-4000, PEG-6000; and co-solvents (propylene glycol, glycerine, PEG-200, PEG-400, PEG-600. Aqueous solubility of drug in case of selected blends (12 blends ranged from 9.091 ± 0.011 mg/ml–43.055 ± 0.14 mg/ml (as compared to the solubility in distilled water 0.072 ± 0.012 mg/ml. The enhancement in the solubility of drug in a mixed solvent containing 10% sodium citrate, 5% sodium benzoate and 25 % S cosolvent (25% S cosolvent contains PEG200, PEG 400, PEG600, Glycerine and Propylene glycol was more than 600 fold. This proved a synergistic enhancement in solubility of a poorly water-soluble drug due to mixed cosolvent effect. Each solubilized product was characterized by ultraviolet and infrared techniques. Various properties of solution such as pH, viscosity, specific gravity and surface tension were studied. The developed formulation was studied for physical and chemical stability. This mixed solvency shall prove definitely a boon for pharmaceutical industries for the development of dosage form of poorly water soluble drugs.

Plasma concentrations of water.soluble vitamins in metabolic ...

African Journals Online (AJOL)

Context: Vitamins B1 (thiamine), B3 (niacin), B6 (pyridoxine), and C (ascorbic acid) are vital for energy, carbohydrate, lipid, and amino acid metabolism and in the regulation of the cellular redox state. Some studies have associated low levels of water.soluble vitamins with metabolic syndrome and its various components.

Coexistence effect of UVA absorbers to increase their solubility and stability of supersaturation.

Science.gov (United States)

Endo, M; Mukawa, T; Sato, N; Maezawa, D; Ohtsu, Y; Kuroda, A; Wakabayashi, M; Asakura, K

2014-12-01

Sunscreens containing UVA absorbers in high concentrations are expected to be developed, since recent studies have suggested the possibility of involvement of UVA ray in skin cancer and early skin aging. Solubility and stability of supersaturation of UVA absorbers in UVB absorber were determined in the absence and the presence of cosmetic oil. Coexistence effect of UVA absorbers was analyzed to dissolve them in high concentrations. Two UVA absorbers, diethylamino hydroxybenzoyl hexyl benzoate (DHHB) and butyl methoxydibenzoylmethane (BMDM), a UVB absorber, 2-ethylhexyl methoxycinnamate (EHMC), and a cosmetic oil, 2-ethylhexyl ester of oligomer of hydroxystearic acid (EH-O-HSA), were used. Their solutions were prepared at 80°C and cooled to 5°C. The solid DHHB and/or BMDM were added to it, and the time evolution of concentrations of the UVA absorbers in the solution phase was monitored. At the saturation in the absence of EH-O-HSA at 5°C, weight ratio of DHHB and BMDM to EHMC was 0.39/1.00 and 0.22/1.00, respectively. Addition of EH-O-HSA slightly changed the solubility of DHHB and BMDM. When the weight ratio of EH-O-HSA to EHMC was 0.20/1.00, weight ratio of DHHB and BMDM to EHMC was 0.35/1.00 and 0.25/1.00, respectively at the saturation at 5°C. In the presence of EH-O-HSA, a strong coexistence effect of DHHB and BMDM was found on their solubility. A thermodynamically stable saturated solution at 5°C having the composition that DHHB: BMDM: EHMC: EH-O-HSA = 0.47: 0.46: 1.00: 0.20 was obtained by the simultaneous addition of solid DHHB and BMDM into the initial solution. The solution type composite having the highest concentrations of DHHB and BMDM prepared in this study exhibited critical wavelength at 368 nm that was just below the border for sunscreens being qualified as 'Broad Spectrum' protection under the new rule launched by US FDA. © 2014 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

Fabrication and evaluation of pH-modulated solid dispersion for telmisartan by spray-drying technique.

Science.gov (United States)

Marasini, Nirmal; Tran, Tuan Hiep; Poudel, Bijay Kumar; Cho, Hyuk Jun; Choi, Young Keun; Chi, Sang-Cheol; Choi, Han-Gon; Yong, Chul Soon; Kim, Jong Oh

2013-01-30

The present study was undertaken to overcome the problems associated with solubility, dissolution and oral bioavailability of a poorly water-soluble ionizable drug, telmisartan (TMS). For these purposes, a solubility test was carried to select the appropriate formulation composition from various carriers and alkalizers. Solid dispersions (SDs) of TMS were prepared at different drug-to-carrier ratios by the spray-drying technique, and were characterized by dissolution and aqueous solubility studies. The optimum formulation was investigated by dissolution studies at different pH and water media and its solid state characterisations were performed by scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and X-ray diffraction (XRD) studies. In solubility and dissolution tests, all TMS-loaded pH-modulated SDs (pH(M)-SDs) exhibited marked improvement in the dissolution behavior when compared with crystalline TMS powder. The optimum formulation of pH(M)-SD consisted of TMS/PVP (polyvinylpyrrolidone) K30/Na(2)CO(3) at a weight ratio of 2/0.5/3 and showed significant improvement in the aqueous solubility and dissolution rate by approximately 40,000- and 3-fold, respectively, compared to TMS powder. Solid-state characterization revealed the changed in crystallinity of TMS into amorphous state. Furthermore, area under the drug concentration time-curve (AUC) of TMS from the pH(M)-SD increased by 13.4- and 2.1-fold, compared with TMS powder and commercial product, respectively. According to these observations, taken together with dissolution and pharmacokinetic behaviors, pH-modulated SD in the presence of an alkalizer for a poorly water-soluble ionizable drug, TMS, appeared to be efficacious for enhancing its bioavailability. Copyright © 2012 Elsevier B.V. All rights reserved.

Solubility and acid-base properties of concentrated phytate in self-medium and in NaCl{sub aq} at T = 298.15 K

Energy Technology Data Exchange (ETDEWEB)

Cigala, Rosalia Maria; Crea, Francesco; Lando, Gabriele; Milea, Demetrio [Dipartimento di Chimica Inorganica, Chimica Analitica e Chimica Fisica, Universita di Messina, Via Ferdinando Stagno d' Alcontres, 31, I-98166 Messina (Vill. S. Agata) (Italy); Sammartano, Silvio, E-mail: ssammartano@unime.i [Dipartimento di Chimica Inorganica, Chimica Analitica e Chimica Fisica, Universita di Messina, Via Ferdinando Stagno d' Alcontres, 31, I-98166 Messina (Vill. S. Agata) (Italy)

2010-11-15

The acid-base properties of concentrated phytic acid were studied in self-medium and in NaCl{sub aq} (0.5 {<=} I/mol . L{sup -1} {<=} 4.0) by ISE-H{sup +} potentiometry and by direct calorimetry, at T = 298.15 K. At ligand concentrations c{sub (Phy)} > 0.012 mol . L{sup -1}, the formation of several binuclear H{sub i}(Phy){sub 2} (2 {<=} i {<=} 10) species was observed, in addition to the mononuclear H{sub i}Phy (1 {<=} i {<=} 7) ones. The solubility of phytate dodecasodium salt was studied in pure water and in NaCl{sub aq} at different ionic strengths; the total solubility in pure water is S{sub 0}{sup T}=(0.300{+-}0.004)mol.L{sup -1} and it decreases markedly with increasing ionic strength; for example the total solubility of Na{sub 12}Phy at I = 3.0 mol . L{sup -1} is 0.008 mol . L{sup -1}. By the dependence on ionic strength (salt concentration) of the solubility, it was possible to calculate the activity coefficients of phytate as a function of medium concentration. Direct calorimetric titrations were also carried out on Na{sub 12}Phy aqueous solutions at different phytate concentrations (0.025 {<=} c{sub (Phy)}/mol . L{sup -1} {<=} 0.100) and without addition of supporting electrolyte, in order to calculate the enthalpy changes for the protonation equilibria in self-medium of the binuclear H{sub i}(Phy){sub 2} species, at T = 298.15 K. It was observed that the {Delta}H/kJ . mol{sup -1} of the binuclear species are, within the experimental error, independent of the ionic strength; for example for the H{sub 2}(Phy){sub 2} species we obtained: {Delta}H{sub 22} = (-23.6 {+-} 0.6) kJ . mol{sup -1}, and (-23.7 {+-} 0.2) kJ . mol{sup -1} at I = 0.50 and 2.0 mol . L{sup -1}, respectively.

Effect of condensed corn distillers solubles concentration on lactation performance of Holstein cows.

Science.gov (United States)

McCormick, M E; Forbes, S; Moreira, V R; Blouin, D C; Han, K J

2015-03-01

Forty-eight Holstein cows (32 multiparous and 16 primiparous) in mid to late lactation averaging 219±71 days in milk and 30.5±6.6 kg/d of 3.5% fat-corrected milk were used in a 56-d completely randomized design experiment to evaluate condensed corn distillers solubles (CCDS) inclusion in high-fiber total mixed rations (TMR). Inclusion rates evaluated were 0, 6.6, 13.2, and 19.8% CCDS as a percentage of dry matter (DM). Distiller solubles substituted for soybean meal, corn grain, and whole cottonseed such that diets were similar in protein (16.6%) and fat (4.50%). Water was added to 0, 6.6, and 13.2% CCDS treatments so that final TMR DM concentrations (47.8%) were similar across diets. The forage portion of the diet was kept constant at 19.6% annual ryegrass hay and 26.0% sorghum baleage. Diet in vitro true digestibility tended to increase as CCDS addition increased, but neutral detergent fiber digestibility trended lower in CCDS diets. Percent P (0.39, 0.55, 0.69, and 0.73%) and S (0.32, 0.35, 0.39, and 0.42%) in TMR increased as CCDS concentration increased. Milk yield (23.5, 24.7, 25.5, and 24.8 kg/d of 3.5% fat-corrected milk) was similar for control and CCDS diets. Milk fat (3.88, 3.73, 3.78, and 3.68%), protein (3.28, 3.27, 3.31, and 3.31%), and lactose (4.61, 4.66, 4.69, and 4.77) percentages were similar across diets. Milk urea nitrogen (16.60, 15.58, 15.43, and 14.75 mg/dL) declined with increasing CCDS addition. Animal activity, body weight, body condition scores, and locomotion scores were not influenced by CCDS. Day 28 poststudy locomotion scores were similar across diets. Ruminal acetate concentrations did not differ among diets, but propionate and butyrate concentrations were elevated in rumen fluid of cows receiving 19.6% CCDS. Although rumen fluid pH values were similar (6.5, 6.4, 6.3, and 6.2), the two highest CCDS diets exhibited depressed acetate:propionate ratios relative to controls. The results from this study indicate that CCDS may be

The complex synthesis and solid state chemistry of ceria-lanthana solid solutions prepared via a hexamethylenetetramine precipitation

International Nuclear Information System (INIS)

Fleming, P.G.; Holmes, J.D.; Otway, D.J.; Morris, M.A.

2011-01-01

Mixed oxide solid solutions are becoming ever more commercially important across a range of applications. However, their synthesis can be problematical. Here, we show that ceria-lanthana solid solutions can be readily prepared via simple precipitation using hexamethylenetetramine. However, the solution chemistry can be complex, which results in the precipitated particles having a complex structure and morphology. Great care must be taken in both the synthesis and characterisation to quantify the complexity of the product. Even very high heat treatments were not able to produce highly homogeneous materials and X-ray diffractions reveals the non-equilibrium form of particles prepared in this way. Unexpected crystal structures are revealed including a new metastable cubic La 2 O 3 phase. - Graphical abstract: The suggested mechanism for the formation of dual fluorite phase particles, where Step 1 corresponds to room temperature aging, Step 2; heating the solution to 90 deg. C, Step 3; cooling of the solution to room temperature, Step 4; calcination to 500 deg. C, Step 5; calcination to 700 deg. C and Step 6; calcination to 1300 deg. C. The terminology of e.g. La 1-x Ce x (OH) 3 is used to indicate the formation of a mixed oxy-hydroxy participate rather than a definitive assignment of stoichiometry. Similarly, La 1-y Ce y O 2 only implies a mixed solid solution. Highlights: → Mol% of prepared Ce-La oxides did not follow that of reactant mol%. → Complex reaction pathway found to be dependent on metal solution concentrations. → At certain concentrations core shell particles were found to form. → A reaction model was produced based on cationic solubility. → Report lanthana solubility higher than previously reported in CeO 2 .

Electrospun 4th-Generation Solid Dispersions of Poorly Water-Soluble Drug Utilizing Two Different Processes

Directory of Open Access Journals (Sweden)

Zhu Zhang

2018-01-01

Full Text Available Different from traditional solid dispersion (SD for improving the dissolution rates of poorly water-soluble drugs, the upgraded 4th SD was developed to furnish a drug sustained-release profile. In this work, two different kinds of 4th SDs were fabricated using two electrospinning processes. One is a ternary SD (nanofibers F2 that consisted of ethyl cellulose (EC, polyethylene glycol 1000 (PEG, and tamoxifen citrate (TAM from a modified coaxial process, and the other is a binary SD (nanofibers F1 which is comprised of EC and TAM from a single-fluid blending process. Scanning electronic microscopic observations demonstrated that F2 (330±50 nm showed a better quality than F1 (870±230 nm in terms of size and size distribution although both of them had a smooth surface morphology and a cross section. X-ray diffraction patterns verified that both SDs were amorphous nanocomposites owing to the favorable secondary interactions among these components, as suggested from the results of FTIR. In vitro dissolution experiments indicated that F2 could furnish an improved drug sustained-release characteristics compared to F1, exhausting all the contained TAM and having weaker leveling-off late release. The molecular behaviors of drug sustained-release from the binary 4th SD were suggested. The protocols reported here paved an alternative way for developing novel functional nanomaterials for effective delivery of poorly water-soluble drugs.

Solubility of solid ferrocene in pressurized hot water

Czech Academy of Sciences Publication Activity Database

Karásek, Pavel; Hohnová, Barbora; Planeta, Josef; Roth, Michal

2010-01-01

Roč. 55, č. 8 (2010), s. 2866-2869 ISSN 0021-9568 R&D Projects: GA ČR GA203/07/0886; GA ČR GA203/08/1465; GA ČR GA203/08/1536 Institutional research plan: CEZ:AV0Z40310501 Keywords : pressurized hot water * ferrocene * solubility Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 2.089, year: 2010

Enhancement of Solubility and Bioavailability of Candesartan ...

African Journals Online (AJOL)

Purpose: To enhance the otherwise poor solubility and bioavailability of candesartan cilexetil (CDS). Methods: This ... PEG 6000-based solid dispersions showed 1st order drug release kinetics. ..... the liver due to quercetin's inhibitory effect on.

Concentrations of Water-Soluble Vitamins in Blood and Urinary Excretion in Patients with Diabetes Mellitus

Directory of Open Access Journals (Sweden)

Hiromi Iwakawa

2016-01-01

Full Text Available We examined the concentrations of water-soluble vitamins in blood and urinary excretion of 22 patients with type 2 diabetes mellitus (type 2DM and 20 healthy control participants. Macronutrient and vitamin intakes of type 2DM subjects were measured using a weighed food record method. Control participants consumed a semipurified diet for eight days. Multiple linear regression models were used to determine whether significant differences existed in vitamin concentrations in blood independent of age, sex, and other confounding factors. Concentrations of vitamins B2, B6, C, niacin, and folate in blood were significantly lower in type 2DM subjects than in controls, independent of confounding factors. Renal clearances of vitamins B6, C, niacin, and folate were significantly higher in type 2DM subjects than in controls. In conclusion, concentrations of vitamins B2, B6, C, niacin, and folate in blood were significantly lower in type 2DM subjects than in controls, independent of confounding factors; based on the evidence of increased urinary clearance of these vitamins, the lower levels were likely due to impaired reabsorption processes.

Concentrations of Water-Soluble Vitamins in Blood and Urinary Excretion in Patients with Diabetes Mellitus.

Science.gov (United States)

Iwakawa, Hiromi; Nakamura, Yasuyuki; Fukui, Tomiho; Fukuwatari, Tsutomu; Ugi, Satoshi; Maegawa, Hiroshi; Doi, Yukio; Shibata, Katsumi

2016-01-01

We examined the concentrations of water-soluble vitamins in blood and urinary excretion of 22 patients with type 2 diabetes mellitus (type 2DM) and 20 healthy control participants. Macronutrient and vitamin intakes of type 2DM subjects were measured using a weighed food record method. Control participants consumed a semipurified diet for eight days. Multiple linear regression models were used to determine whether significant differences existed in vitamin concentrations in blood independent of age, sex, and other confounding factors. Concentrations of vitamins B2, B6, C, niacin, and folate in blood were significantly lower in type 2DM subjects than in controls, independent of confounding factors. Renal clearances of vitamins B6, C, niacin, and folate were significantly higher in type 2DM subjects than in controls. In conclusion, concentrations of vitamins B2, B6, C, niacin, and folate in blood were significantly lower in type 2DM subjects than in controls, independent of confounding factors; based on the evidence of increased urinary clearance of these vitamins, the lower levels were likely due to impaired reabsorption processes.

Regulation of Soluble Phosphate on the Ability of Phytate Mineralization and β-Propeller Phytase Gene Expression of Pseudomonas fluorescens JZ-DZ1, a Phytate-Mineralizing Rhizobacterium.

Science.gov (United States)

Shen, Lan; Wu, Xiao-Qin; Zeng, Qing-Wei; Liu, Hong-Bin

2016-12-01

Phytate-mineralizing rhizobacteria (PMR) play an important role in providing phosphorus for the sustainable plant growth. It is important to investigate the ability of PMR to produce phytase under different phosphate levels for its application. The effects of different concentrations of soluble phosphate on the ability of phytate mineralization of Pseudomonas fluorescens JZ-DZ1, a phytate-mineralizing rhizobacterium, were investigated in both solid and liquid media. The results on solid media showed that halo zone width gradually reduced with concentrations of soluble phosphate increasing from 0.05 to 20 mM, indicating the reduction of the ability of phytate mineralization. The results were consistent with the quantitative detection of phytase activity from the overall trend. An 1866-bp β-propeller phytase (BPP) gene (phyPf) was cloned from the strain, and the deduced amino acid sequence of phyPf shared 98 % of identity with a known BPP from Pseudomonas sp. BS10-3 (AJF36073.1). The results of relative real-time quantitative PCR assay showed that the expression of phyPf was induced by a low concentration (0.1 mM) of soluble phosphate, suggesting that BPP secretion was regulated by gene phyPf. The BPP-harboring bacterium P. fluorescens JZ-DZ1 with low phosphate-inducible ability of phytate mineralization could be potentially applied to promote phosphorus uptake for plants in the future.

Determination of water-soluble and fat-soluble vitamins in tears and blood serum of infants and parents by liquid chromatography/mass spectrometry.

Science.gov (United States)

Khaksari, Maryam; Mazzoleni, Lynn R; Ruan, Chunhai; Kennedy, Robert T; Minerick, Adrienne R

2017-02-01

Tears serve as a viable diagnostic fluid with advantages including less invasive sample to collect and less complex to prepare for analysis. Several water-soluble and fat-soluble vitamins were detected and quantified in human tears and compared with blood serum levels. Samples from 15 family pairs, each pair consisting of a four-month-old infant and one parent were analyzed; vitamin concentrations were compared between tears and blood serum for individual subjects, between infants and parents, and against self-reported dietary intakes. Water-soluble vitamins B 1 , B 2 , B 3 (nicotinamide), B 5 , B 9 and fat-soluble vitamin E (α-tocopherol) were routinely detected in tears and blood serum while fat-soluble vitamin A (retinol) was detected only in blood serum. Water-soluble vitamin concentrations measured in tears and blood serum of single subjects were comparable, while higher concentrations were measured in infants compared to their parents. Fat-soluble vitamin E concentrations were lower in tears than blood serum with no significant difference between infants and parents. Serum vitamin A concentrations were higher in parents than infants. Population trends were compiled and quantified using a cross correlation factor. Strong positive correlations were found between tear and blood serum concentrations of vitamin E from infants and parents and vitamin B 3 concentrations from parents, while slight positive correlations were detected for infants B 3 and parents B 1 and B 2 concentrations. Correlations between infants and parents were found for the concentrations of B 1 , B 2 , B 3 , and E in tears, and the concentrations of B 2, A, and E in blood serum. Stronger vitamin concentration correlations were found between infants and parents for the breast-fed infants, while no significant difference was observed between breast-fed and bottle-fed infants. This work is the first to demonstrate simultaneous vitamin A, B, and E detection and to quantify correlations between

Electrosprayed core–shell solid dispersions of acyclovir fabricated using an epoxy-coated concentric spray head

Science.gov (United States)

Liu, Zhe-Peng; Cui, Lei; Yu, Deng-Guang; Zhao, Zhuan-Xia; Chen, Lan

2014-01-01

A novel structural solid dispersion (SD) taking the form of core–shell microparticles for poorly water-soluble drugs is reported for the first time. Using polyvinylpyrrolidone (PVP) as a hydrophilic polymer matrix, the SDs were fabricated using coaxial electrospraying (characterized by an epoxy-coated concentric spray head), although the core fluids were unprocessable using one-fluid electrospraying. Through manipulating the flow rates of the core drug-loaded solutions, two types of core–shell microparticles with tunable drug contents were prepared. They had average diameters of 1.36±0.67 and 1.74±0.58 μm, and were essentially a combination of nanocomposites with the active ingredient acyclovir (ACY) distributed in the inner core, and the sweeter sucralose and transmembrane enhancer sodium dodecyl sulfate localized in the outer shell. Differential scanning calorimetry and X-ray diffraction results demonstrated that ACY, sodium dodecyl sulfate, and sucralose were well distributed in the PVP matrix in an amorphous state because of favorable second-order interactions. In vitro dissolution and permeation studies showed that the core–shell microparticle SDs rapidly freed ACY within 1 minute and promoted nearly eightfold increases in permeation rate across the sublingual mucosa compared with raw ACY powders. PMID:24790437

Influence of solid state fermentation by Trichoderma spp. on solubility, phenolic content, antioxidant, and antimicrobial activities of commercial turmeric.

Science.gov (United States)

Mohamed, Saleh A; Saleh, Rashad M; Kabli, Saleh A; Al-Garni, Saleh M

2016-05-01

The influence of solid state fermentation (SSF) by Trichoderma spp. on the solubility, total phenolic content, antioxidant, and antibacterial activities of turmeric was determined and compared with unfermented turmeric. The solubility of turmeric was monitored by increase in its phenolic content. The total phenolic content of turmeric extracted by 80% methanol and water after SSF by six species of Trichoderma spp. increased significantly from 2.5 to 11.3-23.3 and from 0.5 to 13.5-20.4 GAE/g DW, respectively. The antioxidant activities of fermented turmeric were enhanced using 2,2-diphenyl-1-picrylhydrazyl (DPPH), 2,2'-azino-bis (3-ethylbenzo-thiazoline-6-sulfonic acid) (ABTS), and ferric ion-reducing antioxidant power (FRAP) assays. The antibacterial activity of fermented turmeric against human-pathogenic bacteria Escherichia coli, Streptococcus agalactiae, Staphylococcus aureus, Entreococcus faecalis, Methicillin-Resistant S. aureus, Klebsiella pneumonia, and Pseudomonas aeruginosae showed a broad spectrum inhibitory effect. In conclusion, the results indicated the potentials of using fermented turmeric as natural antioxidant and antimicrobial material for food applications.

Physicochemical characterization of tacrolimus-loaded solid dispersion with sodium carboxylmethyl cellulose and sodium lauryl sulfate.

Science.gov (United States)

Park, Young-Joon; Ryu, Dong-Sung; Li, Dong Xun; Quan, Qi Zhe; Oh, Dong Hoon; Kim, Jong Oh; Seo, Youn Gee; Lee, Young-Im; Yong, Chul Soon; Woo, Jong Soo; Choi, Han-Gon

2009-06-01

To develop a novel tacrolimus-loaded solid dispersion with improved solubility, various solid dispersions were prepared with various ratios of water, sodium lauryl sulfate, citric acid and carboxylmethylcellulose-Na using spray drying technique. The physicochemical properties of solid dispersions were investigated using scanning electron microscopy, differential scanning calorimetery and powder X-ray diffraction. Furthermore, their solubility and dissolution were evaluated compared to drug powder. The solid dispersion at the tacrolimus/CMC-Na/sodium lauryl sulfate/citric acid ratio of 3/24/3/0.2 significantly improved the drug solubility and dissolution compared to powder. The scanning electron microscopy result suggested that carriers might be attached to the surface of drug in this solid dispersion. Unlike traditional solid dispersion systems, the crystal form of drug in this solid dispersion could not be converted to amorphous form, which was confirmed by the analysis of DSC and powder X-ray diffraction. Thus, the solid dispersion system with water, sodium lauryl sulfate, citric acid and CMC-Na should be a potential candidate for delivering a poorly water-soluble tacrolimus with enhanced solubility and no convertible crystalline.

A REVIEW ON SOLID DISPERSION: A DISSOLUTION ENHANCEMENT TECHNIQUE

OpenAIRE

Ingle U.S.; Gaikwad P.D.; Bankar V.H.; Pawar S.P.

2011-01-01

The enhancement of the oral bioavailability is currently one of the greatest challenges in the development of poorly water soluble drugs. To increase the dissolution and hence the bioavaibility it is important to increase the solubility of the poorly water soluble drugs. One of the possible ways to overcome this limitation is the use of solid dispersion technology. This article contains the different methods and mechanism used in the solid dispersion technology also overlooks the various carr...

Progress in the research of neptunium solubility

International Nuclear Information System (INIS)

Jiang Tao; Liu Yongye; Yao Jun

2012-01-01

237 Np is considered a possible long-term potential threat for environment, because of its long half-life, high toxicity and its mobile nature under aerobic conditions due to the high chemical stability of its pentavalent state. Therefore 237 Np is considered as one of high-level radioactive waste and need to be disposed in deep geologic disposal repository. The dissolution behavior is an important aspect of migration research. The solubility is considered very important for high level waste geological disposal safety and environmental evaluation. The solubility determines the maximum concentration of the discharge, and then it is initial concentration of the radionuclides migration to the environment. The solubility impact directly on radionuclides migration in host rock, and can be used to predict the concentration and speciation of radionuclides in groundwater around disposal sites many years later. This paper focused on research results of the solubility, some proposals for Np dissolution chemistry research were also been suggested. (authors)

Effect of the structure, solid state and lipophilicity on the solubility of novel bicyclic derivatives

International Nuclear Information System (INIS)

Blokhina, Svetlana V.; Ol’khovich, Marina V.; Sharapova, Angelica V.; Volkova, Tatyana V.; Proshin, Alexey N.; Perlovich, German L.

2014-01-01

Highlights: • The solubility in buffer pH 7.4 of novel bicyclo-derivatives of amine were measured. • The influence of melting parameters and lipophilicity on the solubility was studied. • The thermodynamic parameters of the solubility process were calculated. - Abstract: Novel bicyclic derivatives have been synthesized. The solubility of drug-like substances in phosphate buffer rH 7.4 has been measured within the range of (9.02 · 10 −5 to 1.05 · 10 −4 ) mol/l. The relationship between the chemical nature and the structure of the aryl substituents and the solubility parameter was investigated. The fusion temperatures, enthalpies and entropies have been determined experimentally. The influence of thermophysical characteristics and lipophilicity on the solubility was studied using regression analysis. The calculations by the solubility/lipophilicity equation showed an overall improvement of the predictions equal to 0.5 log units. It was concluded that the solvation has a considerable influence on the solubility of the compounds under consideration. It was also determined that the alkyl- and halogen-derivatives solubility values correlate with HYBOT descriptors characterizing the (donor + acceptor) properties of the substances. The thermodynamic parameters of the solubility process were calculated using the temperature dependences. The study also revealed that the solubility of the bicyclic compounds is characterized by high endothermicity of the processes and negative entropies

Supercritical Carbon Dioxide-Soluble Ligands for Extracting Actinide Metal Ions from Porous Solids

International Nuclear Information System (INIS)

Dietz, Mark L.

2001-01-01

Numerous types of actinide-bearing waste materials are found throughout the DOE complex. Most of these wastes consist of large volumes of non-hazardous materials contaminated with relatively small quantities of actinide elements. Separation of these wastes into their inert and radioactive components would dramatically reduce the costs of stabilization and disposal. For example, the DOE is responsible for decontaminating concrete within 7000 surplus contaminated buildings. The best technology now available for removing surface contamination from concrete involves removing the surface layer by grit blasting, which produces a large volume of blasting residue containing a small amount of radioactive material. Disposal of this residue is expensive because of its large volume and fine particulate nature. Considerable cost savings would result from separation of the radioactive constituents and stabilization of the concrete dust. Similarly, gas diffusion plants for uranium enrichment contain valuable high-purity nickel in the form of diffusion barriers. Decontamination is complicated by the extremely fine pores in these barriers, which are not readily accessible by most cleaning techniques. A cost-effective method for the removal of radioactive contaminants would release this valuable material for salvage. The objective of this project is to develop novel, substituted diphosphonic acid ligands that can be used for supercritical carbon dioxide extraction of actinide ions from solid wastes. Specifically, selected diphosphonic acids, which are known to form extremely stable complexes with actinides in aqueous and organic solution, are to be rendered carbon dioxide-soluble by the introduction of appropriate alkyl- or silicon-containing substituents. The metal complexation chemistry of these new ligands in SC-CO2 will then be investigated and techniques for their use in actinide extraction from porous solids developed

Determination of water-soluble vitamins using a colorimetric microbial viability assay based on the reduction of water-soluble tetrazolium salts.

Science.gov (United States)

Tsukatani, Tadayuki; Suenaga, Hikaru; Ishiyama, Munetaka; Ezoe, Takatoshi; Matsumoto, Kiyoshi

2011-07-15

A method for the determination of water-soluble vitamins using a colorimetric microbial viability assay based on the reduction of the tetrazolium salt {2-(2-methoxy-4-nitrophenyl)-3-(4-nitrophenyl)-5-(2,4-disulfophenyl)-2H-tetrazolium, monosodium salt (WST-8)} via 2-methyl-1,4-napthoquinone (NQ) was developed. Measurement conditions were optimized for the microbiological determination of water-soluble vitamins, such as vitamin B(6), biotin, folic acid, niacin, and pantothenic acid, using microorganisms that have a water-soluble vitamin requirement. A linear relationship between absorbance and water-soluble vitamin concentration was obtained. The proposed method was applied to determine the concentration of vitamin B(6) in various foodstuffs. There was good agreement between vitamin B(6) concentrations determined after 24h using the WST-8 colorimetric method and those obtained after 48h using a conventional method. The results suggest that the WST-8 colorimetric assay is a useful method for the rapid determination of water-soluble vitamins in a 96-well microtiter plate. Copyright © 2011 Elsevier Ltd. All rights reserved.

Solubility of salicylic acid in pure alcohols at different temperatures

International Nuclear Information System (INIS)

Lim, Junhyuk; Jang, Sunghyun; Cho, Hye Kyoung; Shin, Moon Sam; Kim, Hwayong

2013-01-01

Highlights: ► Solubility data of salicylic acid in pure alkanols were measured. ► The experimental data were correlated with NRTL, UNIQUAC and Wilson models. ► The data are fit well with all three models for the six pure alcohols studied. ► Adjustable interaction parameters were suggested. - Abstract: This work focused on the experimental measurements and the numerical calculations of the solubility of salicylic acid in various alcohols. The solubility of salicylic acid in pure alcohols was determined using a (solid + liquid) equilibrium measurement apparatus at temperatures ranging from (278.15 to 318.15) K. Also, the melting temperature and fusion enthalpy of salicylic acid were determined by a differential scanning calorimeter (TA instrument Q100). The experimental results were correlated with the equation for solubility of a solid in a liquid with the nonrandom two liquid (NRTL), universal quasi-chemical (UNIQUAC) and Wilson models for liquid phase activity coefficients to validate the quality of the data taken. Adjustable interaction parameters were also provided. The experimental data fit appropriately with all three models for the pure alcohols studied.

Steady-state oxygen-solubility in niobium

International Nuclear Information System (INIS)

Schulze, K.; Jehn, H.

1977-01-01

During annealing of niobium in oxygen in certain temperature and pressure ranges steady states are established between the absorption of molecular oxygen and the evaporation of volatile oxides. The oxygen concentration in the niobium-oxygen α-solid solution is a function of oxygen pressure and temperature and has been redetermined in the ranges 10 -5 - 10 -2 Pa O 2 and 2,070 - 2,470 K. It follows differing from former results the equation csub(o) = 9.1 x 10 -6 x sub(po2) x exp (502000/RT) with csub(o) in at.-ppm, sub(po2) in Pa, T in K, R = 8.31 J x mol -1 x K -1 . The existence of steady states is limited to a temperature range from 1870 to 2470 K and to oxygen concentrations below the solubility limit given by solidus and solvus lines in the T-c diagram. In the experiments high-purity niobium wires with a specific electrical ratio rho (273 K)/rho(4.2 K) > 5,000 have been gassed under isothermal-isobaric conditions until the steady state has been reached. The oxygen concentration has been determined analytically by vacuum fusion extraction with platinum-flux technique as well as by electrical residual resistivity measurements at 4.2 K. (orig.) [de

Solubility of xenon in amino-acid solutions. II. Nine less-soluble amino acids

Science.gov (United States)

Kennan, Richard P.; Himm, Jeffrey F.; Pollack, Gerald L.

1988-05-01

Ostwald solubility (L) of xenon gas, as the radioisotope 133Xe, has been measured as a function of solute concentration, at 25.0 °C, in aqueous solutions of nine amino acids. The amino-acid concentrations investigated covered much of their solubility ranges in water, viz., asparagine monohydrate (0-0.19 M), cysteine (0-1.16 M), glutamine (0-0.22 M), histidine (0-0.26 M), isoleucine (0-0.19 M), methionine (0-0.22 M), serine (0-0.38 M), threonine (0-1.4 M), and valine (0-0.34 M). We have previously reported solubility results for aqueous solutions of six other, generally more soluble, amino acids (alanine, arginine, glycine, hydroxyproline, lysine, and proline), of sucrose and sodium chloride. In general, L decreases approximately linearly with increasing solute concentration in these solutions. If we postulate that the observed decreases in gas solubility are due to hydration, the results under some assumptions can be used to calculate hydration numbers (H), i.e., the number of H2O molecules associated with each amino-acid solute molecule. The average values of hydration number (H¯) obtained at 25.0 °C are 15.3±1.5 for asparagine, 6.8±0.3 for cysteine, 11.5±1.1 for glutamine, 7.3±0.7 for histidine, 5.9±0.4 for isoleucine, 10.6±0.8 for methionine, 11.2±1.3 for serine, 7.7± 1.0 for threonine, and 6.6±0.6 for valine. We have also measured the temperature dependence of solubility L(T) from 5-40 °C for arginine, glycine, and proline, and obtained hydration numbers H¯(T) in this range. Between 25-40 °C, arginine has an H¯ near zero. This may be evidence for an attractive interaction between xenon and arginine molecules in aqueous solution.

SOLUBILITY AND BIOAVAILABILITY ENHANCEMENT STRATEGIES FOR EFFECTIVE DELIVERY OF POORLY WATER SOLUBLE DRUGS BY NANO FORMULATIONS AND SOLID DISPERSIONS

OpenAIRE

Rayapolu Ranga Goud*, Gunnala Krishnaveni, Girija Prasad Patro

2018-01-01

For the ancient few years, there has been a substantial research done on diverse methodologies for poorly water soluble and lipophilic drugs. More in modern times voluminous molecules cannot be distributed due to low solubility. Now a day frequently, particulate vesicle systems such as nanoparticles, liposomes, microspheres, niosomes, pronisomes, ethosomes, and proliposomes have been used as drug carriers. Drug delivery designates the technique and methodology to conveying medications or drug...

Molybdenum solubility in aluminium nitrate solutions

Energy Technology Data Exchange (ETDEWEB)

Heres, X.; Sans, D.; Bertrand, M.; Eysseric, C. [CEA, Centre de Marcoule, Nuclear Energy Division, DRCP, BP 17171, 30207 Bagnols-sur-Ceze Cedex (France); Brackx, E.; Domenger, R.; Excoffier, E. [CEA, Centre de Marcoule, Nuclear Energy Division, DTEC, BP 17171, 30207 Bagnols-sur-Ceze Cedex (France); Valery, J.F. [AREVA-NC, DOR/RDP, Paris - La Defense (France)

2016-07-01

For over 60 years, research reactors (RR or RTR for research testing reactors) have been used as neutron sources for research, radioisotope production ({sup 99}Mo/{sup 99m}Tc), nuclear medicine, materials characterization, etc... Currently, over 240 of these reactors are in operation in 56 countries. They are simpler than power reactors and operate at lower temperature (cooled to below 100 C. degrees). The fuel assemblies are typically plates or cylinders of uranium alloy and aluminium (U-Al) coated with pure aluminium. These fuels can be processed in AREVA La Hague plant after batch dissolution in concentrated nitric acid and mixing with UOX fuel streams. The aim of this study is to accurately measure the solubility of molybdenum in nitric acid solution containing high concentrations of aluminium. The higher the molybdenum solubility is, the more flexible reprocessing operations are, especially when the spent fuels contain high amounts of molybdenum. To be most representative of the dissolution process, uranium-molybdenum alloy and molybdenum metal powder were dissolved in solutions of aluminium nitrate at the nominal dissolution temperature. The experiments showed complete dissolution of metallic elements after 30 minutes long stirring, even if molybdenum metal was added in excess. After an induction period, a slow precipitation of molybdic acid occurs for about 15 hours. The data obtained show the molybdenum solubility decreases with increasing aluminium concentration. The solubility law follows an exponential relation around 40 g/L of aluminium with a high determination coefficient. Molybdenum solubility is not impacted by the presence of gadolinium, or by an increasing concentration of uranium. (authors)

Gravitational settling of a highly concentrated system of solid spherical particles

Science.gov (United States)

Arkhipov, V. A.; Usanina, A. S.

2017-09-01

In the present paper, we report on the results of an experimental study of the process of gravity sedimentation of a cloud of monodispersed solid spherical particles with initial volume concentration C > 0.03, which was performed in a wide range of Reynolds numbers. An analytical estimate of the settling regimes of spherical particle clouds is presented. A new method for creating a spherical particle cloud with a high concentration of particles is proposed. A qualitative picture of the settling process of a highly concentrated particle cloud under gravity is revealed. A criterial dependence for the drag coefficient of a sedimenting spherical particle cloud as an entity is obtained.

Solubility of Tc(IV) oxides

International Nuclear Information System (INIS)

Liu, D.J.; Fan, X.H.

2005-01-01

Full text of publication follows: The deep geological disposal of the high level radioactive wastes is expected to be a safer disposal method in most countries. The long-lived fission product 99 Tc is present in large quantities in nuclear wastes and its chemical behavior in aqueous solution is of considerable interest. Under the reducing conditions, expected to exist in a deep geological repository, it is generally predicted that technetium will be present as TcO 2 .nH 2 O. The solubility of Tc(IV) is used as a source term in performance assessment of radioactive waste repository. Technetium oxide was prepared by reduction of a technetate solution with Sn 2+ . The solubility of Tc(IV) oxide has been determined in simulated groundwater and re-distilled water under aerobic and anaerobic conditions. The effects of pH and CO 3 2- concentration of solution on solubility of Tc(IV) oxide were studied. The concentration of total technetium and Tc(IV) species in the solutions were periodically determined by separating the oxidized and reduced technetium species using a solvent extraction procedure and counting the beta activity of the 99 Tc with a liquid scintillation counter. The experimental results show that the rate of oxidation of Tc(IV) in simulated groundwater and re-distilled water is about (1.49∼1.86) x 10 -9 mol/(L.d) under aerobic conditions, but Tc(IV) in simulated groundwater and re-distilled water is not oxidized under anaerobic conditions. Under aerobic or anaerobic conditions the solubility of Tc(IV) oxide in simulated groundwater and re-distilled water is equal on the whole after centrifugation or ultrafiltration. The solubility of Tc(IV) oxide decreases with the increase of pH at pH 10 and is pH independent in the range 2 -8 to 10 -9 mol/L at 2 3 2- concentration. These data could be used to estimate the Tc(IV) solubility for cases where solubility limits transport of technetium in reducing environments of high-level waste repositories. (authors)

Nota científica: Avaliação sensorial de geleia de marmelo 'Japonês' em diferentes concentrações de sólidos solúveis totais Scientific note: Sensory evaluation of japanese quince jam with different concentrations of total soluble solids

Directory of Open Access Journals (Sweden)

Gustavo das Graças Pereira

2011-09-01

Full Text Available As plantas do marmeleiro 'Japonês' (Chaenomeles sinensis Koehne vem sendo amplamente pesquisadas nos últimos anos em função da alta produtividade, da resistência à entomosporiose e da capacidade de servir como porta-enxerto para as demais cultivares. Visando propiciar o aproveitamento dessa cultivar para o consumo humano, o presente trabalho objetivou desenvolver e avaliar a aceitação da geleia de marmelo 'Japonês' em diferentes concentrações de sólidos solúveis totais. Os frutos utilizados no experimento foram colhidos na Fazenda Experimental da EPAMIG, localizada no município de Maria da Fé-MG. Para a obtenção das geleias, os frutos foram processados até se obter um produto final com as concentrações de 66, 68 e 70 °Brix de sólidos solúveis totais. O teste de aceitação foi realizado por um grupo de 50 julgadores não treinados que avaliaram aparência, consistência, aroma, sabor, aspecto global e intenção de compra dos diferentes tratamentos. Os resultados obtidos revelaram que as geleias de marmelo 'Japonês' apresentaram uma boa aceitação para todos os atributos avaliados, sendo que, de uma forma geral, as amostras com 68 e 70 °Brix obtiveram maior aceitabilidade e intenção de compra pelos julgadores.In recent years, Japanese quince (Chaenomeles sinensis Koehne plants have been widely studied due to their high productivity, resistance to entomosporium and ability to serve as rootstock for other cultivars. In order to facilitate the use of this cultivar for human consumption, the present study aimed to develop and evaluate the acceptance of a Japanese quince jam with different concentrations of total soluble solids. The fruits used in the experiment were harvested at the Experimental Farm of EPAMIG, located in the city of Maria da Fé, MG, Brazil. To obtain the jams, the fruits were processed to obtain a final product with concentrations of 66, 68 and 70 °Brix with respect to the total soluble solids

Sorption of Arsenic from Desalination Concentrate onto Drinking Water Treatment Solids: Operating Conditions and Kinetics

Directory of Open Access Journals (Sweden)

Xuesong Xu

2018-01-01

Full Text Available Selective removal of arsenic from aqueous solutions with high salinity is required for safe disposal of the concentrate and protection of the environment. The use of drinking water treatment solids (DWTS to remove arsenic from reverse osmosis (RO concentrate was studied by batch sorption experiments. The impacts of solution chemistry, contact time, sorbent dosage, and arsenic concentration on sorption were investigated, and arsenic sorption kinetics and isotherms were modeled. The results indicated that DWTS were effective in removing arsenic from RO concentrate. The arsenic sorption process followed a pseudo-second-order kinetic model. Multilayer adsorption was simulated by Freundlich equation. The maximum sorption capacities were calculated to be 170 mg arsenic per gram of DWTS. Arsenic sorption was enhanced by surface precipitation onto the DWTS due to the high amount of calcium in the RO concentrate and the formation of ternary complexes between arsenic and natural organic matter (NOM bound by the polyvalent cations in DWTS. The interactions between arsenic and NOM in the solid phase and aqueous phase exhibited two-sided effects on arsenic sorption onto DWTS. NOM in aqueous solution hindered the arsenic sorption onto DWTS, while the high organic matter content in solid DWTS phase enhanced arsenic sorption.

Separation of oils from solids

International Nuclear Information System (INIS)

Van Slyke, D.C.

1992-01-01

This patent describes a method for cleaning oil-contaminated particulate solids. It comprises: contacting contaminated solids with a non-aqueous liquid composition comprising a carboxylic acid; then contacting the solids with an aqueous wash containing a reagent for converting the carboxylic acid to a water-soluble carboxylate salt; and removing an aqueous phase containing carboxylate salt and entrained oil

Physicochemical characterization of atorvastatin calcium/ezetimibe amorphous nano-solid dispersions prepared by electrospraying method.

Science.gov (United States)

Jahangiri, Azin; Barzegar-Jalali, Mohammad; Javadzadeh, Yousef; Hamishehkar, Hamed; Adibkia, Khosro

2017-09-01

In the present study, electrospraying was applied as a novel method for the fabrication of amorphous nano-solid dispersions (N-SDs) of atorvastatin calcium (ATV), ezetimibe (EZT), and ATV/EZT combination as poorly water-soluble drugs. N-SDs were prepared using polyvinylpyrrolidone K30 as an amorphous carrier in 1:1 and 1:5 drug to polymer ratios and the total solid (including drug and polymer) concentrations of 10 and 20% (w/v). The prepared formulations were further investigated for their morphological, physicochemical, and dissolution properties. Scanning electron microscopy studies indicated that the morphology and diameter of the electrosprayed samples (ESs) were influenced by the solution concentration and drug:polymer ratio, so that an increase in the solution concentration resulted in fiber formation while an increase in the polymer ratio led to enhancement of the particle diameter. Differential scanning calorimetry and X-ray powder diffraction studies together with in vitro dissolution test revealed that the ESs were present in an amorphous form with improved dissolution properties. Infrared spectroscopic studies showed hydrogen-bonding interaction between the drug and polymer in ESs. Since the electrospraying method benefits from the both amorphization and nanosizing effect, this novel approach seems to be an efficient method for the fabrication of N-SDs of poorly water-soluble drugs.

Accounting for genotype–by-environment interactions and non-additive genetic variation in genomic selection for water-soluble carbohydrate concentration in wheat

Science.gov (United States)

Abiotic stress tolerance traits are often complex and recalcitrant targets for conventional breeding improvement in many crop species. This study evaluated the potential of genomic selection to predict water-soluble carbohydrate concentration (WSCC), an important drought tolerance trait, in wheat un...

Selective hydrogenation of 1,3-butadiene from crude C{sub 4} cracker stream with a solid catalyst with ionic liquid layer (SCILL). DSC and solubility study

Energy Technology Data Exchange (ETDEWEB)

Mangartz, T.; Korth, W.; Kern, C.; Jess, A. [Bayreuth Univ. (Germany). Dept. of Chemical Engineering

2013-11-01

In petroleum as well as in fine chemical industry, selective catalytic hydrogenation is an important reaction. The selective hydrogenation of 1,3-butadiene (BD) to butene (trans-,1- and cis-butene) from the crude C4 steam cracker fraction represents one example, but under today's technical conditions undesired butane forms inevitably in relevant amounts. To increase the butene yield, the concept of Solid Catalyst with Ionic Liquid Layer (SCILL) was employed. The SCILL catalyst, in contrast to the uncoated catalyst, yielded a remarkably high selectivity to butenes (S{sub butenes} > 99 %) even at high residence times or at high hydrogen partial pressure. Nearly no butane (S{sub butane} {approx} 0 %) was analytically detected. We expected that due to different solubility, the poorer soluble compounds discharged from the ionic liquid and, thus, caused the shift in selectivity to a great extent. Temperature dependent solubility measurements in the used ionic liquid ([DMIM][DMP]) revealed that the order of increasing solubility is 1,3-butadiene > butenes > butane which matches the assumption. However, since differences in solubility cannot explain this SCILL effect satisfyingly, ionic liquids are expected to affect the surface of the catalyst (side-specific ligand-type effect). Investigations using spectroscopic methods (e.g. FTIR) confirmed this suggestion. (orig.)

Adsorption of heavy metals by road deposited solids.

Science.gov (United States)

Gunawardana, Chandima; Goonetilleke, Ashantha; Egodawatta, Prasanna

2013-01-01

The research study discussed in the paper investigated the adsorption/desorption behaviour of heavy metals commonly deposited on urban road surfaces, namely, Zn, Cu, Cr and Pb, for different particle size ranges of solids. The study outcomes, based on field studies and batch experiments, confirmed that road deposited solids particles contain a significantly high amount of vacant charge sites with the potential to adsorb additional heavy metals. Kinetic studies and adsorption experiments indicated that Cr is the most preferred metal element to associate with solids due to the relatively high electronegativity and high charge density of trivalent cation (Cr(3+)). However, the relatively low availability of Cr in the urban road environment could influence this behaviour. Comparing total adsorbed metals present in solids particles, it was found that Zn has the highest capacity for adsorption to solids. Desorption experiments confirmed that a low concentration of Cu, Cr and Pb in solids was present in water-soluble and exchangeable form, whilst a significant fraction of adsorbed Zn has a high likelihood of being released back into solution. Among heavy metals, Zn is considered to be the most commonly available metal among road surface pollutants.

Hydrogen-induced delayed cracking: 1. Strain energy effects on hydrogen solubility

International Nuclear Information System (INIS)

Puls, M.P.

1978-08-01

Based on Li, Oriani and Darken's derivation of the chemical potential of a solute in a stressed solid and Eshelby's method for obtaining the strain energy of solids containing coherent inhomogeneous inclusions, we have carried out a detailed theoretical analysis of the factors governing hydrogen solubility in stressed and unstressed zirconium and its alloys. Specifically, the analysis demonstrates the strong influence hydride self-stresses may have on the terminal solid solubility of hydrogen in zirconium. The self-energy arises due to the misfit strains between matrix and precipitate. We have calculated the total molal self-strain energy of some commonly observed δ and γ-hydride shapes and orientations. The magnitude of this energy is substantial. Thus for γ-hydride plates lying on basal planes, it is 4912 J/mol, while for γ-hydride needles with the needle axis parallel to the directions of the α-zirconium matrix, it is 2662 J/mol. This self-strain energy causes a shift in the terminal solid solubility. For example, at 77 o C, assuming fully constrained basal plane δ-hydride plates, the terminal solid solubility is increased 5.4 times over the stress-free case. We have also calculated the effect of external stress on the terminal solid solubility. This is governed by the interaction energy arising from the interaction of the applied stresses with the precipitate's misfit strain components. The interaction energy has been calculated for δ and γ-hydride plates and needles, taking full account of the anisotropy of the misfit. The interaction energy is negative for tensile applied stresses and, as a result of the anisotropic misfit, is texture-dependent. Its magnitude is small for most applied stresses but can achieve values of the order of the self-strain energy in the plastic zone of a plane-strain crack. We have also carried out a careful analysis of the solubility data of Kearns and Erickson and Hardie. This analysis is based partly on the theoretical

Sample Results from MCU Solids Outage

Energy Technology Data Exchange (ETDEWEB)

Peters, T.; Washington, A.; Oji, L.; Coleman, C.; Poirier, M.

2014-09-22

additional details are provided below as recommendations. From this point on, IC-Anions analyses of the DSSHT should be part of the monthly routine analysis in order to spot negative trends in the oxalate leaving the MCU system. Care must be taken to monitor the oxalate content to watch for sudden precipitation of oxalate salts in the system; Conduct a study to optimize the cleaning strategy at ARP-MCU through decreasing the concentration or entirely eliminating the oxalic acid; The contents of the SSFT should remain unagitated. Routine visual observation should be maintained to ensure there is not a large buildup of solids. As water with agitation provided sufficient removal of the solids in the feed tank, it should be considered as a good means for dissolving oxalate solids if they are found in the future; Conduct a study to improve prediction of oxalate solubility in salt batch feed materials. As titanium and mercury have been found in various solids in this report, evaluate if either element plays a role in oxalate solubility during processing; Salt batch characterization focuses primarily on characterization and testing of unaltered Tank 21H material; however, non-typical feeds are developed through cleaning, washing, and/or sump transfers. As these solutions are processed through MCU, they may precipitate solids or reduce performance. Salt batch characterization and testing should be expanded to encompass a broader range of feeds that may be processed through ARPMCU.

Leaching behavior of harmful components from cement solidities of fluidized-bed coal ash

Energy Technology Data Exchange (ETDEWEB)

Baba, T.; Fukuoka, H.; Shigemoto, N. [Fuji Clean Co., Kagawa (Japan)

2008-07-15

Solidifies of fluidized-bed fly ash with slag cement were prepared by hydrothermal treatment after adding gypsum, Na3PO{sub 4}, or Al2(SO{sub 4}){sub 3}. XRD analysis of the solidifies was performed and leaching behavior of Pb and F from the solidities was investigated. The fly ash-cement and fly ash-cement-gypsum solidifies showed rather high leaching concentration of F and Pb. The F leaching was explained by solubility products of a Ca(OH){sub 2} CaF2 system. The Pb leaching concentrations roughly agreed with the theoretical curve for hydroxo complexes of Pb, showing a strong dependence on pH. Addition of Na3PO{sub 4} and Al2(SO{sub 4}){sub 3}, to cement solidities gave katoite and aluminium phosphate, and ettringite, respectively, and these solidities showed lower leaching concentrations of F and Pb than the fly ash-cement and fly ash-cement-gypsum solidifies. Capture of F and Pb in crystalline components such as ettringite probably accounts for such leaching suppression.

The thermodynamics and kinetics of interstitial solid solutions

International Nuclear Information System (INIS)

Silva, J.R.G. da.

1976-04-01

Studies of hydrogen metal systems where the hidrogen is disolved in a solid solution are presented. Particular items of interest are: the thermodynamics of the hydrogen-iron system; the solubility of hidrogen in super pure iron single crytals; the thermodinamic functions of hydrogen in solid solutions of Nb, Ta and V; and the solubility of hydrogen in α-manganese. The diffusion of carbon and nitrogen in BCC iron is also studied

Thermodynamic Study of Solid-Liquid Equilibrium in NaCl-NaBr-H2O System at 288.15 K

Science.gov (United States)

Li, Dan; Meng, Ling-zong; Deng, Tian-long; Guo, Ya-fei; Fu, Qing-Tao

2018-06-01

The solubility data, composition of the solid solution and refractive indices of the NaCl-NaBr-H2O system at 288.15 K were studied with the isothermal equilibrium dissolution method. The solubility diagram and refractive index diagram of this system were plotted at 288.15 K. The solubility diagram consists of two crystallization zones for solid solution Na(Cl,Br) · 2H2O and Na(Cl,Br), one invariant points cosaturated with two solid solution and two univariant solubility isothermal curves. On the basis of Pitzer and Harvie-Weare (HW) chemical models, the composition equations and solubility equilibrium constant equations of the solid solutions at 288.15 K were acquired using the solubility data, the composition of solid solutions, and binary Pitzer parameters. The solubilities calculated using the new method combining the equations are in good agreement with the experimental data.

Impact of chemistry on Standard High Solids Vessel Design mixing

Energy Technology Data Exchange (ETDEWEB)

Poirier, M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2016-03-02

The plan for resolving technical issues regarding mixing performance within vessels of the Hanford Waste Treatment Plant Pretreatment Facility directs a chemical impact study to be performed. The vessels involved are those that will process higher (e.g., 5 wt % or more) concentrations of solids. The mixing equipment design for these vessels includes both pulse jet mixers (PJM) and air spargers. This study assesses the impact of feed chemistry on the effectiveness of PJM mixing in the Standard High Solids Vessel Design (SHSVD). The overall purpose of this study is to complement the Properties that Matter document in helping to establish an acceptable physical simulant for full-scale testing. The specific objectives for this study are (1) to identify the relevant properties and behavior of the in-process tank waste that control the performance of the system being tested, (2) to assess the solubility limits of key components that are likely to precipitate or crystallize due to PJM and sparger interaction with the waste feeds, (3) to evaluate the impact of waste chemistry on rheology and agglomeration, (4) to assess the impact of temperature on rheology and agglomeration, (5) to assess the impact of organic compounds on PJM mixing, and (6) to provide the technical basis for using a physical-rheological simulant rather than a physical-rheological-chemical simulant for full-scale vessel testing. Among the conclusions reached are the following: The primary impact of precipitation or crystallization of salts due to interactions between PJMs or spargers and waste feeds is to increase the insoluble solids concentration in the slurries, which will increase the slurry yield stress. Slurry yield stress is a function of pH, ionic strength, insoluble solids concentration, and particle size. Ionic strength and chemical composition can affect particle size. Changes in temperature can affect SHSVD mixing through its effect on properties such as viscosity, yield stress, solubility

Thermodynamic model of Ni(II) solubility, hydrolysis and complex formation with ISA

Energy Technology Data Exchange (ETDEWEB)

Gonzalez-Siso, Maria Rosa; Duro, Lara; Bruno, Jordi [Amphos21, Barcelona (Spain); Gaona, Xavier; Altmaier, Marcus [Karlsruhe Institute of Technology (KIT), Karlsruhe (Germany). Inst. for Nuclear Waste Disposal

2018-04-01

The solubility of β-Ni(OH){sub 2}(cr) was investigated at T=(22±2) C in the absence and presence of α-isosaccharinic acid (ISA), the main degradation product of cellulose under alkaline pH conditions. Batch solubility experiments were performed from undersaturation conditions under inert gas (Ar) atmosphere. Solubility experiments in the absence of ISA were conducted in 0.5 and 3.0 M NaCl-NaOH solutions at 7.5 ≤ pH{sub m} ≤ 13 (with pH{sub m} = -log{sub 10}[H{sup +}]). XRD analyses of selected solid phases collected after completing the solubility experiments (∼300 days) confirmed that β-Ni(OH){sub 2}(cr) remains as solid phase controlling the solubility of Ni(II) in all investigated conditions. Based on the slope analysis (log{sub 10}[Ni] vs. pH{sub m}) of the solubility data and solid phase characterization, the equilibrium reactions β-Ni(OH){sub 2}(cr)+2 H{sup +} <=> Ni{sup 2+}+2 H{sub 2}O(l) and β-Ni(OH){sub 2}(cr) <=> Ni(OH){sub 2}(aq) were identified as controlling the solubility of Ni(II) within the investigated pH{sub m} region. The conditional equilibrium constants determined from the solubility experiments at different ionic strengths were evaluated with the specific ion interaction theory (SIT). In contrast to the current thermodynamic selection in the NEA-TDB, solubility data collected in the present work does not support the formation of the anionic hydrolysis species Ni(OH){sub 3}{sup -} up to pH{sub m} ≤ 13.0. Solubility experiments in the presence of ISA were conducted in 0.5 M NaCl-NaOH-NaISA solutions with 0.01 M ≤ [NaISA] ≤ 0.2 M and 9 ≤ pH{sub m} ≤ 13. XRD analyses confirmed that β-Ni(OH){sub 2}(cr) is also the solid phase controlling the solubility of Ni(II) in the presence of ISA. Solubility data of all investigated systems can be properly explained with chemical and thermodynamic models including the formation of the complexes NiOHISA(aq), Ni(OH){sub 2}ISA{sup -} and Ni(OH){sub 3}ISA{sup 2-}. The reported data confirm

Influence of three different concentration techniques on evaporation rate, color and phenolics content of blueberry juice.

Science.gov (United States)

Elik, Aysel; Yanık, Derya Koçak; Maskan, Medeni; Göğüş, Fahrettin

2016-05-01

The present study was undertaken to assess the effects of three different concentration processes open-pan, rotary vacuum evaporator and microwave heating on evaporation rate, the color and phenolics content of blueberry juice. Kinetics model study for changes in soluble solids content (°Brix), color parameters and phenolics content during evaporation was also performed. The final juice concentration of 65° Brix was achieved in 12, 15, 45 and 77 min, for microwave at 250 and 200 W, rotary vacuum and open-pan evaporation processes, respectively. Color changes associated with heat treatment were monitored using Hunter colorimeter (L*, a* and b*). All Hunter color parameters decreased with time and dependently studied concentration techniques caused color degradation. It was observed that the severity of color loss was higher in open-pan technique than the others. Evaporation also affected total phenolics content in blueberry juice. Total phenolics loss during concentration was highest in open-pan technique (36.54 %) and lowest in microwave heating at 200 W (34.20 %). So, the use of microwave technique could be advantageous in food industry because of production of blueberry juice concentrate with a better quality and short time of operation. A first-order kinetics model was applied to modeling changes in soluble solids content. A zero-order kinetics model was used to modeling changes in color parameters and phenolics content.

Enhancement of dissolution of Telmisartan through use of solid dispersion technique surface solid dispersion

Directory of Open Access Journals (Sweden)

Bhumika Patel

2012-01-01

Full Text Available The present study was aimed to increase the solubility of the poorly water soluble drug Telmisartan by using Surface solid dispersion (SSD made of polymers like Poloxamer 407, PEG 6000 by Solvent evaporation method. The drug was solubilized by surfactants and/or polymers then adsorbed onto the surface of extremely fine carriers to increase its surface area and to form the SSD which give the more Surface area for absorption of the drug. A 2 2 full factorial design was used to investigate for each carrier the joint influence of formulation variables: Amount of carrier and adsorbent. Saturation solubility studies shows the improvement in solubility of drug batch SSD 8 give more solubility improvement than the other batch, in-vitro dissolution of pure drug, physical mixtures and SSDs were carried out in that SSDs were found to be effective in increasing the dissolution rate of Telmisartan in form of SSD when compared to pure drug. Also FT-IR spectroscopy, differential scanning calorimetry and X-ray diffractometry studies were carried out in order to characterize the drug and Surface solid dispersion. Furthermore, both DSC and X-ray diffraction showed a decrease in the melting enthalpy and reduced drug crystallinity consequently in SSDs. However, infrared spectroscopy revealed no drug interactions with the carriers.

Solubilities of oxygenated aromatic solids in pressurized hot water

Czech Academy of Sciences Publication Activity Database

Karásek, Pavel; Planeta, Josef; Roth, Michal

2009-01-01

Roč. 54, č. 5 (2009), s. 1457-1461 ISSN 0021-9568 R&D Projects: GA ČR GA203/07/0886; GA ČR GA203/08/1536 Institutional research plan: CEZ:AV0Z40310501 Keywords : oxygenated aromatics * solubility * pressurized hot water Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 1.695, year: 2009

Nootkatone encapsulation by cyclodextrins: Effect on water solubility and photostability.

Science.gov (United States)

Kfoury, Miriana; Landy, David; Ruellan, Steven; Auezova, Lizette; Greige-Gerges, Hélène; Fourmentin, Sophie

2017-12-01

Nootkatone (NO) is a sesquiterpenoid volatile flavor, used in foods, cosmetics and pharmaceuticals, possessing also insect repellent activity. Its application is limited because of its low aqueous solubility and stability; this could be resolved by encapsulation in cyclodextrins (CDs). This study evaluated the encapsulation of NO by CDs using phase solubility studies, Isothermal Titration Calorimetry, Nuclear Magnetic Resonance spectroscopy and molecular modeling. Solid CD/NO inclusion complex was prepared and characterized for encapsulation efficiency and loading capacity using UV-Visible. Thermal properties were investigated by thermogravimetric-differential thermal analysis and release studies were performed using multiple headspace extraction. Formation constants (K f ) proved the formation of stable inclusion complexes. NO aqueous solubility, photo- and thermal stability were enhanced and the release could be insured from solid complex in aqueous solution. This suggests that CDs are promising carrier to improve NO properties and, consequently, to enlarge its use in foods, cosmetics, pharmaceuticals and agrochemicals preparations. Copyright © 2016 Elsevier Ltd. All rights reserved.

Implications of Industrial Processing Strategy on Cellulosic Ethanol Production at High Solids Concentrations

DEFF Research Database (Denmark)

Cannella, David

The production of cellulosic ethanol is a biochemical process of not edible biomasses which contain the cellulose. The process involves the use of enzymes to hydrolyze the cellulose in fermentable sugars to finally produce ethanol via fermentative microorganisms (i.e. yeasts). These biomasses...... are the leftover of agricultural productions (straws), not edible crops (giant reed) or wood, thus the ethanol so produced is also called second generation (or 2G ethanol), which differs from the first generation produced from starch (sugar beets mostly). In the industrial production of cellulosic ethanol high...... solids strategy resulted critical for its cost effectiveness: high concentration of initial biomass it will lead to high concentration of the final product (ethanol), thus more convenient to isolate. This thesis investigate the implementation of a high solids loading concept into cellulosic ethanol...

Thermodynamic phase behavior of API/polymer solid dispersions.

Science.gov (United States)

Prudic, Anke; Ji, Yuanhui; Sadowski, Gabriele

2014-07-07

To improve the bioavailability of poorly soluble active pharmaceutical ingredients (APIs), these materials are often integrated into a polymer matrix that acts as a carrier. The resulting mixture is called a solid dispersion. In this work, the phase behaviors of solid dispersions were investigated as a function of the API as well as of the type and molecular weight of the carrier polymer. Specifically, the solubility of artemisinin and indomethacin was measured in different poly(ethylene glycol)s (PEG 400, PEG 6000, and PEG 35000). The measured solubility data and the solubility of sulfonamides in poly(vinylpyrrolidone) (PVP) K10 and PEG 35000 were modeled using the perturbed-chain statistical associating fluid theory (PC-SAFT). The results show that PC-SAFT predictions are in a good accordance with the experimental data, and PC-SAFT can be used to predict the whole phase diagram of an API/polymer solid dispersion as a function of the kind of API and polymer and of the polymer's molecular weight. This remarkably simplifies the screening process for suitable API/polymer combinations.

Measurement and modelling of urea solubility in aqueous propane-1,2,3-triol and prop-2-enoic acid solutions

International Nuclear Information System (INIS)

Santos, Jéssica dos J; Rocha, João A.A.B.; Costa, Glória M.N.; Cabral-Albuquerque, Elaine C.M.; Alves, Tito L.M.; Pinto, José C.; Fialho, Rosana L.

2016-01-01

Highlights: • Solubilities were shown to increase with temperature and to decrease with the increasing organic solvent content. • The UNIFAC method provided good fitting of the available data, after the estimation of a single model parameter. • The empirical method showed to be more efficient to describe several solution concentrations however, it is not predictive. - Abstract: The aim of the present study is to measure the solubility of urea in aqueous solutions of prop-2-enoic acid and propane-1,2,3-triol, as these compounds are used as co-monomers to produce urea base co-polymers. Experimental values have been obtained at several concentrations and temperatures. Solubility results were modelled with the help of an exponential empirical correlation, ideal solid-liquid equilibrium correlation and the Universal Functional Activity Coefficient (UNIFAC) method, used to describe the activity coefficient in the liquid phase. The empirical correlation requires two empirical parameters for each solvent and leads to the best fit for the available data. The UNIFAC method correlation also has a good numerical performance and is completely predictive, and it does not require the estimation of additional parameters.

On the solubility advantage of a pharmaceutical’s glassy state over the crystal state, and of its crystal polymorphs

International Nuclear Information System (INIS)

Johari, G.P.; Shanker, Ravi M.

2014-01-01

Highlights: • Heat capacity data do not yield the solubility advantage of amorphous and metastable crystal pharmaceuticals. • There is no reversible equilibrium of an amorphous solid with its saturated solution. • Solubility advantage of an amorphous solid depends upon the solvent and other interactions. - Abstract: At equilibrium, the saturation solubility and vapor pressure of a material in a state of high free energy are greater than in its state of low free energy. This knowledge from classical thermodynamics is currently used for increasing the solubility of crystalline pharmaceuticals by producing them in their glassy state, or in other solid states of high free energy. The ratio of the apparent saturation solubility of these solids to that of a crystal, calculated from the thermodynamic data of the pure solute, ϕ cal , is called the solubility advantage, and it is used as a guide for increasing the solubility of a pharmaceutical. We argue that the ϕ cal differs from the measured solubility ratio, ϕ meas , because, (i) ϕ cal is independent of the solvent, but ϕ meas is not so, (ii) ϕ cal would increase with the dissolution time monotonically to a constant value, but ϕ meas would first reach a maximum and then decrease, and (iii) approximations are made in estimating ϕ cal and the effect of thermal history on high free energy solids is ignored. On the other hand, ϕ meas is affected by, (a) another chemical equilibrium in the solution, e.g., hydrogen-bond formation and ionic dissociation, (b) the production method and thermal history of a glass or an amorphous samples, and (c) mutarotation in the solution, isomerization or tautomeric conversion in the solid. We also discuss the effects of structural relaxation and crystallization on ϕ meas . The ϕ meas value of a (crystal) polymorph would be affected by all the three, and further if the polymorph is orientationally disordered. We provide evidence for these effects from analysis of the known

Maximum solid concentrations of coal water slurries predicted by neural network models

Energy Technology Data Exchange (ETDEWEB)

Cheng, Jun; Li, Yanchang; Zhou, Junhu; Liu, Jianzhong; Cen, Kefa

2010-12-15

The nonlinear back-propagation (BP) neural network models were developed to predict the maximum solid concentration of coal water slurry (CWS) which is a substitute for oil fuel, based on physicochemical properties of 37 typical Chinese coals. The Levenberg-Marquardt algorithm was used to train five BP neural network models with different input factors. The data pretreatment method, learning rate and hidden neuron number were optimized by training models. It is found that the Hardgrove grindability index (HGI), moisture and coalification degree of parent coal are 3 indispensable factors for the prediction of CWS maximum solid concentration. Each BP neural network model gives a more accurate prediction result than the traditional polynomial regression equation. The BP neural network model with 3 input factors of HGI, moisture and oxygen/carbon ratio gives the smallest mean absolute error of 0.40%, which is much lower than that of 1.15% given by the traditional polynomial regression equation. (author)

Ash behavior during hydrothermal treatment for solid fuel applications. Part 2: Effects of treatment conditions on industrial waste biomass

International Nuclear Information System (INIS)

Mäkelä, Mikko; Yoshikawa, Kunio

2016-01-01

Highlights: • Effect of treatment conditions on composition and solubility of ash. • Ash dissolution and yield governed by liquid pH and calcium carbonate solubility. • Dissolution of calcium carbonate decreases ash fusion temperature during combustion. • Decreasing the ash content of sludge can weaken ash properties for combustion. - Abstract: This second half of our work on ash behavior concentrates on the effects of hydrothermal treatment conditions on paper sludge. Ash composition and solubility were determined based on treatment temperature, reactor solid load and liquid pH using experimental design and univariate regression methods. In addition, ash properties for combustion were evaluated based on recent developments on ash classification. Based on the results, all experimental variables had a statistically significant effect on ash yields. Only reactor solid load was statistically insignificant for char ash content, which increased based on increasing treatment temperature due to the decomposition of organic components. Ash dissolution and ash yield were governed by liquid pH and the generation of acids mainly due to the solubility of calcium carbonate identified as the main mineral species of paper sludge. Dissolution of calcium carbonate however decreased ash fusion temperatures more likely causing problems during char incineration. This indicated that decreasing the ash content of sludge during hydrothermal treatment can actually weaken ash properties for solid fuel applications.

Micro-scale prediction method for API-solubility in polymeric matrices and process model for forming amorphous solid dispersion by hot-melt extrusion.

Science.gov (United States)

Bochmann, Esther S; Neumann, Dirk; Gryczke, Andreas; Wagner, Karl G

2016-10-01

A new predictive micro-scale solubility and process model for amorphous solid dispersions (ASDs) by hot-melt extrusion (HME) is presented. It is based on DSC measurements consisting of an annealing step and a subsequent analysis of the glass transition temperature (Tg). The application of a complex mathematical model (BCKV-equation) to describe the dependency of Tg on the active pharmaceutical ingredient (API)/polymer ratio, enables the prediction of API solubility at ambient conditions (25°C). Furthermore, estimation of the minimal processing temperature for forming ASDs during HME trials could be defined and was additionally confirmed by X-ray powder diffraction data. The suitability of the DSC method was confirmed with melt rheological trials (small amplitude oscillatory system). As an example, ball milled physical mixtures of dipyridamole, indomethacin, itraconazole and nifedipine in poly(vinylpyrrolidone-co-vinylacetate) (copovidone) and polyvinyl caprolactam-polyvinyl acetate-polyethylene glycol graft copolymer (Soluplus®) were used. Copyright © 2016 Elsevier B.V. All rights reserved.

PEI detoxification of pretreated spruce for high solids ethanol fermentation

International Nuclear Information System (INIS)

Cannella, David; Sveding, Per Viktor; Jørgensen, Henning

2014-01-01

Highlights: • High solids (30% dry matter) pretreatment, enzymatic hydrolysis and fermentation. • Horizontal rotary reactor for hydrolysis and fermentation. • In situ hydrolysates detoxification using inhibitors adsorbing PEI polymer. • 50% of inhibitors recovered as by-product, recyclability of PEI polymer up to 5 times. • 76% of maximum theoretical ethanol was fermented at final concentration of 51 g/kg. - Abstract: Performing the bioethanol production process at high solids loading is a requirement for economic feasibility at industrial scale. So far this has successfully been achieved using wheat straw and other agricultural residues at 30% of water insoluble solids (WIS), but for softwood species (i.e. spruce) this has been difficult to reach. The main reason behind this difference is the higher recalcitrance of woody substrates which require harsher pretreatment conditions, thus generating higher amounts of inhibitory compounds, ultimately lowering fermentation performances. In this work we studied ethanol production from spruce performing the whole process, from pretreatment to hydrolysis and fermentation, at 30% dry matter (equivalent to ∼20% WIS). Hydrolysis and fermentation was performed in a horizontal free fall mixing reactor enabling efficient mixing at high solids loadings. In batch simultaneous saccharification and fermentation (SSF), up to 76% cellulose to ethanol conversion was achieved resulting in a concentration of 51 g/kg of ethanol. Key to obtaining this high ethanol yield at these conditions was the use of a detoxification technology based on applying a soluble polyelectrolyte polymer (polyethylenimine, PEI) to absorb inhibitory compounds in the material. On average 50% removal and recovery of the main inhibitors (HMF, furfural, acetic acid and formic acid) was achieved dosing 1.5% w/w of soluble PEI. The use of PEI was compatible with operating the process at high solids loadings and enabled fermentation of hydrolysates, which

Assessment of the Binding of Protons, Al and Fe to Biochar at Different pH Values and Soluble Metal Concentrations

Directory of Open Access Journals (Sweden)

Tan Dang

2018-01-01

Full Text Available Biochar can retain large amounts of protons and metals in the drainage water from acid sulfate soils and mine sites. Metal sorption can, however, be influenced by many factors, such as pH and metal composition. This study investigated proton, Al, and Fe retention capacity of eucalyptus biochar (1% w/v at different pH and metal concentrations. In the absence of metals, the biochar had a high proton binding capacity, (up to 0.035 mmol of H+, whereas its capacity to retain hydroxide ions was limited. A batch experiment was carried out at pH 4 and pH 7 with 10−6, 10−5, 10−4, 10−3, and 10−2 M of added Fe or Al. Added metals precipitated considerably prior to addition of the biochar except that Al remained highly soluble at pH 4. The biochar had a high retention capacity for Al and Fe; at high (>1 mM concentrations, over 80% of soluble metals were retained. Metal competition for binding sites of both Al and Fe at different ratios was investigated, but increasing concentrations of one metal did not reduce retention of the other. The results confirmed that biochar has high metal binding capacity under both acidic and neutral conditions.

Predicting Soluble Nickel in Soils Using Soil Properties and Total Nickel.

Science.gov (United States)

Zhang, Xiaoqing; Li, Jumei; Wei, Dongpu; Li, Bo; Ma, Yibing

2015-01-01

Soil soluble nickel (Ni) concentration is very important for determining soil Ni toxicity. In the present study, the relationships between soil properties, total and soluble Ni concentrations in soils were developed in a wide range of soils with different properties and climate characteristics. The multiple regressions showed that soil pH and total soil Ni concentrations were the most significant parameters in predicting soluble Ni concentrations with the adjusted determination coefficients (Radj2) values of 0.75 and 0.68 for soils spiked with soluble Ni salt and the spiked soils leached with artificial rainwater to mimic field conditions, respectively. However, when the soils were divided into three categories (pH 8), they obtained better predictions with Radj2 values of 0.78-0.90 and 0.79-0.94 for leached and unleached soils, respectively. Meanwhile, the other soil properties, such as amorphous Fe and Al oxides and clay, were also found to be important for determining soluble Ni concentrations, indicating that they were also presented as active adsorbent surfaces. Additionally, the whole soil speciation including bulk soil properties and total soils Ni concentrations were analyzed by mechanistic speciation models WHAM VI and Visual MINTEQ3.0. It was found that WHAM VI provided the best predictions for the soils with pH 8. The Visual MINTEQ3.0 could provide better estimation for pH 8. These results indicated the possibility and applicability of these models to predict soil soluble Ni concentration by soil properties.

On the water-soluble organic nitrogen concentration and mass size distribution during the fog season in the Po Valley, Italy.

Science.gov (United States)

Montero-Martínez, Guillermo; Rinaldi, Matteo; Gilardoni, Stefania; Giulianelli, Lara; Paglione, Marco; Decesari, Stefano; Fuzzi, Sandro; Facchini, Maria Cristina

2014-07-01

The study of organic nitrogen gained importance in recent decades due to its links with acid rain, pollution, and eutrophication. In this study, aerosol and fog water samples collected from two sites in Italy during November 2011 were analyzed to characterize their organic nitrogen content. Organic nitrogen contributed 19-25% of the total soluble nitrogen in the aerosol and around 13% in fog water. The largest water soluble organic nitrogen concentrations in the PM1.2 fraction occurred during the diurnal period with mean values of 2.03 and 2.16 μg-N m(-3) (154 and 145 nmol-N m(-3)) at Bologna and San Pietro Capofiume (SPC), respectively. The mean PM10 WSON concentration during diurnal periods at SPC was 2.30 μg-N m(-3) (164 nmol-N m(-3)) while it was 1.34 and 0.82 μg-N m(-3) (95.7 and 58.5 nmol-N m(-3)) in the night and fog water samples, respectively. Aerosol mass distribution profiles obtained during fog changed significantly with respect to those estimated in periods without fog periods due to fog scavenging, which proved to be over 80% efficient. Linear correlations suggested secondary processes related to combustion and, to a lesser extent, biomass burning, as plausible sources of WSON. Regarding the inorganic nitrogen fraction, the results showed that ammonium was the largest soluble inorganic nitrogen component in the samples. Copyright © 2014 Elsevier B.V. All rights reserved.

Resveratrol cocrystals with enhanced solubility and tabletability.

Science.gov (United States)

Zhou, Zhengzheng; Li, Wanying; Sun, Wei-Jhe; Lu, Tongbu; Tong, Henry H Y; Sun, Changquan Calvin; Zheng, Ying

2016-07-25

Two new 1:1 cocrystals of resveratrol (RES) with 4-aminobenzamide (RES-4ABZ) and isoniazid (RES-ISN) were synthesized by liquid assisted grinding (LAG) and rapid solvent removal (RSR) methods using ethanol as solvent. Their physiochemical properties were characterized using PXRD, DSC, solid state and solution NMR, FT-IR, and HPLC. Pharmaceutically relevant properties, including tabletability, solubility, intrinsic dissolution rate, and hygroscopicity, were evaluated. Temperature-composition phase diagram for RES-ISN cocrystal system was constructed from DSC data. Both cocrystals show higher solubility than resveratrol over a broad range of pH. They are phase stable and non-hygroscopic even under high humidity conditions. Importantly, both cocrystals exhibit improved solubility and tabletability compared with RES, which make them more suitable candidates for tablet formulation development. Copyright © 2016 Elsevier B.V. All rights reserved.

Bioleaching of pollymetallic sulphide concentrate using thermophilic bacteria

Directory of Open Access Journals (Sweden)

Vuković Milovan

2014-01-01

Full Text Available An extreme thermophilic, iron-sulphur oxidising bacterial culture was isolated and adapted to tolerate high metal and solids concentrations at 70°C. Following isolation and adaptation, the culture was used in a batch bioleach test employing a 5-l glass standard magnetic agitated and aerated reactor, for the bioleaching of a copper-lead-zinc collective concentrate. The culture exhibited stable leach performance over the period of leach operation and overall copper and zinc extractions higher than 97%. Lead sulphide is transformed into lead sulphate remaining in the bioleach residue due to the low solubility in sulphate media. Brine leaching of bioleach residue yields 95% lead extraction. [Projekat Ministarstva nauke Republike Srbije, br. 34023

The effect of acute physical and mental stress on soluble cellular adhesion molecule concentration.

Science.gov (United States)

Crabb, E Blake; Franco, R Lee; Caslin, Heather L; Blanks, Anson M; Bowen, Mary K; Acevedo, Edmund O

2016-07-15

This study investigated the impact of acute physical and mental stress on serum concentrations of vascular cell adhesion molecule (VCAM)-1 and CX3CL1/fractalkine. Male volunteers (n=20; 21.3±0.55years of age) completed a graded treadmill test to exhaustion and a 20-minute mental stress task (Stroop Color-Word Test, mental arithmetic) on separate, non-consecutive days. Heart rate (HR) was measured at baseline and throughout exercise and mental stress. Blood was collected at baseline (PRE), immediately following (POST) and 30min after (POST30) exercise and mental stress. Soluble VCAM-1 and fractalkine were quantified in participant serum via enzyme-linked immunosorbent assays. Both treadmill exercise and the mental stress task significantly increased participant HR; although, exercise resulted in a substantially greater increase in participant HR compared to mental stress (197.82±11.99 vs. 38.67±3.10% [pstress task did not significantly alter serum VCAM-1 or fractalkine at any time point. In conclusion, maximal aerobic exercise results in a significant elevation of the soluble adhesion molecules VCAM-1 and fractalkine in the serum of adult males that does not occur following laboratory-induced mental stress. The findings of the current investigation may suggest a novel protective role for acute aerobic exercise in vascular health via exercise-induced CAM proteolysis. Copyright © 2016 Elsevier Inc. All rights reserved.

Dissolution rate enhancement of repaglinide by solid dispersion

African Journals Online (AJOL)

Keywords: Diabetes, Solid dispersion, Repaglinide, Solubility, Dissolution, Burst release. Tropical Journal of ... high lipophilicity (logP = 3.97) and relatively low oral bioavailability (56 .... II drug, i.e., low soluble and high permeable in nature. As.

Co-precipitation and solubility studies of cesium, potassium and sodium tetraphenylborate

International Nuclear Information System (INIS)

Peterson, R.A.

1999-01-01

This report contains the results from a study requested by High Level Waste Division on the co-precipitation and solubility of cesium, potassium, and sodium tetraphenylborate. Co-precipitation of cesium (Cs), potassium (K), and sodium (Na) tetraphenylborate (TPB) helps determine the efficiency of reagent usage in the Small Tank Precipitation Process. This process uses NaTPB to remove cesium from waste by means of precipitation. Previous studies by McCabe suggested that if the sodium ion concentration [Na+] increased the rate at which cesium tetraphenylborate (KTPB) in the presence of high [Na+] (∼5M) appears to produce a mixed solid phase composed of NaTPB and KTPB together in the crystal lattice

Structural Characterization of Febuxostat/l-Pyroglutamic Acid Cocrystal Using Solid-State 13C-NMR and Investigational Study of Its Water Solubility

Directory of Open Access Journals (Sweden)

Ji-Hun An

2017-12-01

Full Text Available Febuxostat (FB is a poorly water-soluble drug that belongs to BCS class II. The drug is employed for the treatment of inflammatory disease arthritis urica (gout, and the free base, FB form-A, is most preferred for drug formulation. In order to achieve a goal of improving the water solubility of FB form-A, this study was carried out using the cocrystallization technique called the liquid-assisted grinding method to produce FB cocrystals. Here, five amino acids containing amine (NH, oxygen (O, and hydroxyl (OH functional groups, and possessing difference of pKa less than 3 with FB, were selected as coformers. Then, solvents including methanol, ethanol, isopropyl alcohol, n-hexane, dichloromethane, and acetone were used for the cocrystal screening. As a result, a cocrystal was obtained when acetone and l-pyroglutamic acid (PG of 0.5 eq. were employed as solvent and coformer, respectively. The ratio of 2:1, which is the ratio of FB to PG within FB-PG cocrystal, was predicted by means of solid-state CP/MAS 13C-NMR, solution-state NMR (1H, 13C, and 2D and FT-IR. Moreover, Powder X-ray Diffraction (PXRD, Differential Scanning Calorimetry (DSC, and Thermogravimetric Analysis (TGA were used to investigate the characteristics of FB-PG cocrystal. In addition, comparative solubility tests between FB-PG cocrystal and FB form-A were conducted in deionized water and under simulated gastrointestinal pH (1.2, 4, and 6.8 conditions. The result revealed that FB-PG cocrystal has a solubility of four-fold higher than FB form-A in deionized water and two-fold and five-fold greater than FB form-A at simulated gastrointestinal pH 1.2 and pH 4, respectively. Besides, solubilities of FB-PG cocrystal and FB form-A at pH 6.8 were similar to the results measured in deionized water. Therefore, it is postulated that FB-PG cocrystal has a potential overcoming the limitations related to the low aqueous solubility of FB form-A. Accordingly, FB-PG cocrystal is suggested as an

Influence of lactose hydrolysis and solids concentration on alcohol production by yeast in acid whey ultrafiltrate

Energy Technology Data Exchange (ETDEWEB)

O' leary, V S; Sutton, C; Bencivengo, M; Sullivan, B; Holsinger, V H

1977-11-01

Alcohol yields of 6.5 percent were obtained with Saccharomyces cerevisiae in lactase-hydrolyzed acid whey permeate containing 30 to 35 percent total solids. Maximum alcohol yields obtained with Kluyveromyces fragilis were 4.5 percent in lactase-hydrolyzed acid whey permeate at a solids concentration of 20 percent and 3.7 percent in normal permeate at a solids concentration of 10 percent. Saccharomyces cerevisiae efficiently converted the glucose present in lactase-hydrolyzed whey permeates containing 5 to 30 percent total solids (2 to 13 percent glucose) to alcohol. However, the galactose, which comprised about half the available carbohydrate in lactase-hydrolyzed whey, was not utilized by S. cerevisiae, so that even though alcohol yields were higher when this organism was used, the process was wasteful in that a substantial proportion of the substrate was not fermented. For the process to become commercially feasible, an efficient means of rapidly converting both the galactose and glucose to alcohol must be found.

DEVELOPMENT OF SUSTAINED RELEASE TABLETS CONTAINING SOLID DISPERSIONS OF BACLOFEN

Directory of Open Access Journals (Sweden)

K. H. Janardhana

2015-07-01

Full Text Available Sustained release tablets containing solid dispersions granules of a poorly water soluble drug were prepared to investigate the controlled release of the drug. Baclofen was chosen because of its poor water solubility and short elimination half-life. Poloxamer 188 and PEG 6000 were used as solid dispersion carrier. Free flowing solid dispersion granules were prepared by adsorbing the melt of the drug and carriers onto the surface of an adsorbent, Carbopol 934P followed by direct compression with HPMC K4M and HPMC K100 to obtain an solid dispersion loaded sustained release tablets. FTIR studies confirmed that the compatibility of drug and carriers. Differential scanning calorimetry (DSC and X-ray diffraction (XRD revealed partially amorphous structures of the drug in solid dispersion granules. The solid dispersion granules dissolved completely within 30 min, which was much faster than that of pure drug baclofen. The sustained release of baclofen from the solid dispersion containing tablet was achieved for 2 h in gastric fluid (pH 1.2 and for up to 10 h in intestinal fluid (pH 6.8. A combination of solid dispersion techniques using adsorption and sustained release concepts is a promising approach to control the release rate of poorly water-soluble drugs.

DEVELOPMENT OF SUSTAINED RELEASE TABLETS CONTAINING SOLID DISPERSIONS OF BACLOFEN

Directory of Open Access Journals (Sweden)

K. H. Janardhana

2013-12-01

Full Text Available Sustained release tablets containing solid dispersions granules of a poorly water soluble drug were prepared to investigate the controlled release of the drug. Baclofen was chosen because of its poor water solubility and short elimination half-life. Poloxamer 188 and PEG 6000 were used as solid dispersion carrier. Free flowing solid dispersion granules were prepared by adsorbing the melt of the drug and carriers onto the surface of an adsorbent, Carbopol 934P followed by direct compression with HPMC K4M and HPMC K100 to obtain an solid dispersion loaded sustained release tablets. FTIR studies confirmed that the compatibility of drug and carriers. Differential scanning calorimetry (DSC and X-ray diffraction (XRD revealed partially amorphous structures of the drug in solid dispersion granules. The solid dispersion granules dissolved completely within 30 min, which was much faster than that of pure drug baclofen. The sustained release of baclofen from the solid dispersion containing tablet was achieved for 2 h in gastric fluid (pH 1.2 and for up to 10 h in intestinal fluid (pH 6.8. A combination of solid dispersion techniques using adsorption and sustained release concepts is a promising approach to control the release rate of poorly water-soluble drugs.

Round Robin test for the determination of nitrogen concentration in solid Lithium

International Nuclear Information System (INIS)

Favuzza, P.; Antonelli, A.; Furukawa, T.; Groeschel, F.; Hedinger, R.; Higashi, T.; Hirakawa, Y.; Iijima, M.; Ito, Y.; Kanemura, T.; Knaster, J.; Kondo, H.; Miccichè, G.; Nitti, F.S.; Ohira, S.; Severi, M.; Sugimoto, M.; Suzuki, A.; Traversi, R.; Wakai, E.

2016-01-01

Highlights: • Nitrogen contained in solid Lithium is converted into Ammonium ion. • Ammonium ion is suitably quantified by ionic chromatograph or by Ammonia sensor. • Good agreement of the partner’s results has been achieved. • Maximum operative reproducibility and blank subtraction are necessary. - Abstract: Three different partners, ENEA, JAEA ed University of Tokyo, have been involved during 2014–2015 in the Round Robin experimentation for the assessment of the soundness of the analitycal procedure for the determination of the Nitrogen impurities contained inside a solid Lithium sample. Two different kinds of Lithium samples, differing by about an order of magnitude in Nitrogen concentration (∼230 wppm; ∼20–30 wppm), have been selected for this cross analysis. The agreement of the achieved results appears very good for what concerns the most concentrated Lithium and indicates each partner’s procedure is appropriate and intrinsecally able to lead to meaningful values, characterized by a relative uncertainty of just few %. The smaller agreement in the case of the less concentrated Lithium anyway points out that particular attention must be paid to reduce as much as possible any source of external contamination and highlights the importance of the proper blank subtraction.

Round Robin test for the determination of nitrogen concentration in solid Lithium

Energy Technology Data Exchange (ETDEWEB)

Favuzza, P., E-mail: paolo.favuzza@enea.it [ENEA Center, Via Madonna del Piano 10, 50019 Sesto Fiorentino (Italy); Antonelli, A. [ENEA Research Center, Brasimone, 40035, Camugnano (Italy); Furukawa, T. [JAEA Research Center, Tokai-mura, Ibaraki (Japan); Groeschel, F. [KIT Research Center, Hermann-von-Helmholtz-Platz 1,76344 Eggenstein-Leopoldshafen (Germany); Hedinger, R. [F4E Research Center, Boltzmannstraße 2, 85748 Garching (Germany); Higashi, T. [University of Tokyo (Japan); Hirakawa, Y.; Iijima, M.; Ito, Y.; Kanemura, T. [JAEA Research Center, Tokai-mura, Ibaraki (Japan); Knaster, J. [IFMIF-EVEDA Project Team, Rokkasho (Japan); Kondo, H. [JAEA Research Center, Tokai-mura, Ibaraki (Japan); Miccichè, G.; Nitti, F.S. [ENEA Research Center, Brasimone, 40035, Camugnano (Italy); Ohira, S. [JAEA Research Center, Tokai-mura, Ibaraki (Japan); Severi, M. [University of Firenze, Via della Lastruccia 3, 50019 Sesto Fiorentino (Italy); Sugimoto, M. [JAEA Research Center, Rokkasho (Japan); Suzuki, A. [University of Tokyo (Japan); Traversi, R. [University of Firenze, Via della Lastruccia 3, 50019 Sesto Fiorentino (Italy); Wakai, E. [JAEA Research Center, Tokai-mura, Ibaraki (Japan)

2016-06-15

Highlights: • Nitrogen contained in solid Lithium is converted into Ammonium ion. • Ammonium ion is suitably quantified by ionic chromatograph or by Ammonia sensor. • Good agreement of the partner’s results has been achieved. • Maximum operative reproducibility and blank subtraction are necessary. - Abstract: Three different partners, ENEA, JAEA ed University of Tokyo, have been involved during 2014–2015 in the Round Robin experimentation for the assessment of the soundness of the analitycal procedure for the determination of the Nitrogen impurities contained inside a solid Lithium sample. Two different kinds of Lithium samples, differing by about an order of magnitude in Nitrogen concentration (∼230 wppm; ∼20–30 wppm), have been selected for this cross analysis. The agreement of the achieved results appears very good for what concerns the most concentrated Lithium and indicates each partner’s procedure is appropriate and intrinsecally able to lead to meaningful values, characterized by a relative uncertainty of just few %. The smaller agreement in the case of the less concentrated Lithium anyway points out that particular attention must be paid to reduce as much as possible any source of external contamination and highlights the importance of the proper blank subtraction.

Solid solubility of MgO in the calcium silicates of portland clinker. The effect of CaF2

Directory of Open Access Journals (Sweden)

Puertas, F.

1992-03-01

Full Text Available The solid solubility of MgO in the calcium silicates of portland clinker has been determined by XRD and XDS. The influence that the presence of CaF2 has on said solubility has also been verified. The solid solution limit of MgO in C3S at 1275 ºC lies at about 1.0% wt, where the triclinic form II stabilizes. The presence of CaF2 does not alter the maximum value of the MgO solubilized in that silicate, although there does take place the stabilization of the triclinic polymorph II at lower MgO contents (between 0.3 - 0.6% wt. The maximum amount of solubilized MgO in βC2 at 1.050 ºC lies around 0.5% wt. This value does not change by the presence of CaF2.Se ha determinado por DRX y EDX la solubilidad sólida del MgO en los silicatos cálcicos del clínker portland. Se ha comprobado, así mismo la influencia que sobre dicha solubilidad tiene la presencia de CaF2. El límite de disolución sólida del MgO en el C3S a 1.275º C se sitúa alrededor del 1,0% en peso, estabilizándose la forma triclínica II. La presencia de CaF2 no altera el valor máximo de MgO solubilizado en este silicato, aunque si se produce la estabilización del polimorfo triclínico II a contenidos menores de MgO (entre 0,3 – 0,6% en peso. La cantidad máxima de MgO solubilizado en e/ βC2S a 1.050 ºC se sitúa en torno al 0,5% en peso. Este valor no se ve modificado por la presencia de CaF2.

Solubility study of Tc(IV) oxides

International Nuclear Information System (INIS)

Liu, D.J.; Fan, X.H.

2005-01-01

The deep geological disposal of the high level radioactive wastes is expected to be a safer disposal method in most countries. The long-lived fission product 99 Tc is present in large quantities in nuclear wastes and its chemical behavior in aqueous solution is of considerable interest. Under oxidizing conditions technetium exists as the anionic species TcO 4 - whereas under the reducing conditions, expected to exist in a deep geological repository, it is generally predicted that technetium will be present as TcO 2 ·nH 2 O. Hence, the mobility of Tc(IV) in reducing groundwater may be limited by the solubility of TcO 2 ·nH 2 O under these conditions. Due to this fact it is important to investigate the solubility of TcO 2 ·nH 2 O. The solubility determines the release of radionuclides from waste form and is used as a source term in radionuclide migration analysis in performance assessment of radioactive waste repository. Technetium oxide was prepared by reduction of a technetate solution with Sn 2 + . The solubility of Tc(IV) oxide has been determined in simulated groundwater and redistilled water under aerobic and anaerobic conditions. The effects of pH and CO 3 2- concentration of solution on solubility of Tc(IV) oxide were studied. The concentration of total technetium and Tc(IV) species in the solutions were periodically determined by separating the oxidized and reduced technetium species using a solvent extraction procedure and counting the beta activity of the 99 Tc with a liquid scintillation counter. The experimental results show that the rate of oxidation of Tc(IV) in simulated groundwater and redistilled water is about (1.49-1.86) x 10 -9 mol/(L·d) under aerobic conditions, but Tc(IV) in simulated groundwater and redistilled water is not oxidized under anaerobic conditions. Under aerobic or anaerobic conditions the solubility of Tc(IV) oxide in simulated groundwater and redistilled water is equal on the whole after centrifugation or ultrafiltration. The

THE STRUCTURE AND CONCENTRATION OF SOLIDS IN PHOTORECEPTOR CELLS STUDIED BY REFRACTOMETRY AND INTERFERENCE MICROSCOPY

Science.gov (United States)

Sidman, Richard L.

1957-01-01

Fragments of freshly obtained retinas of several vertebrate species were studied by refractometry, with reference to the structure of the rods and cones. The findings allowed a reassessment of previous descriptions based mainly on fixed material. The refractometric method was used also to measure the refractice indices and to calculate the concentrations of solids and water in the various cell segments. The main quantitative data were confirmed by interference microscopy. When examined by the method of refractometry the outer segments of freshly prepared retinal rods appear homogeneous. Within a few minutes a single eccentric longitudinal fiber appears, and transverse striations may develop. These changes are attributed to imbibition of water and swelling in structures normally too small for detection by light microscopy. The central "core" of outer segments and the chromophobic disc between outer and inner segments appear to be artifacts resulting from shrinkage during dehydration. The fresh outer segments of cones, and the inner segments of rods and cones also are described and illustrated. The volumes, refractive indices, concentrations of solids, and wet and dry weights of various segments of the photoreceptor cells were tabulated. Rod outer segments of the different species vary more than 100-fold in volume and mass but all have concentrations of solids of 40 to 43 per cent. Cone outer segments contain only about 30 per cent solids. The myoids, paraboloids, and ellipsoids of the inner segments likewise have characteristic refractive indices and concentrations of solids. Some of the limitations and particular virtues of refractometry as a method for quantitative analysis of living cells are discussed in comparison with more conventional biochemical techniques. Also the shapes and refractive indices of the various segments of photoreceptor cells are considered in relation to the absorption and transmission of light. The Stiles-Crawford effect can be accounted

Novel furosemide cocrystals and selection of high solubility drug forms.

Science.gov (United States)

Goud, N Rajesh; Gangavaram, Swarupa; Suresh, Kuthuru; Pal, Sharmistha; Manjunatha, Sulur G; Nambiar, Sudhir; Nangia, Ashwini

2012-02-01

Furosemide was screened in cocrystallization experiments with pharmaceutically acceptable coformer molecules to discover cocrystals of improved physicochemical properties, that is high solubility and good stability. Eight novel equimolar cocrystals of furosemide were obtained by liquid-assisted grinding with (i) caffeine, (ii) urea, (iii) p-aminobenzoic acid, (iv) acetamide, (v) nicotinamide, (vi) isonicotinamide, (vii) adenine, and (viii) cytosine. The product crystalline phases were characterized by powder x-ray diffraction, differential scanning calorimetry, infrared, Raman, near IR, and (13) C solid-state NMR spectroscopy. Furosemide-caffeine was characterized as a neutral cocrystal and furosemide-cytosine an ionic salt by single crystal x-ray diffraction. The stability of furosemide-caffeine, furosemide-adenine, and furosemide-cytosine was comparable to the reference drug in 10% ethanol-water slurry; there was no evidence of dissociation of the cocrystal to furosemide for up to 48 h. The other five cocrystals transformed to furosemide within 24 h. The solubility order for the stable forms is furosemide-cytosine > furosemide-adenine > furosemide-caffeine, and their solubilities are approximately 11-, 7-, and 6-fold higher than furosemide. The dissolution rates of furosemide cocrystals were about two times faster than the pure drug. Three novel furosemide compounds of higher solubility and good phase stability were identified in a solid form screen. Copyright © 2011 Wiley Periodicals, Inc.

Enhancing the solubility and bioavailability of poorly water-soluble drugs using supercritical antisolvent (SAS) process.

Science.gov (United States)

Abuzar, Sharif Md; Hyun, Sang-Min; Kim, Jun-Hee; Park, Hee Jun; Kim, Min-Soo; Park, Jeong-Sook; Hwang, Sung-Joo

2018-03-01

Poor water solubility and poor bioavailability are problems with many pharmaceuticals. Increasing surface area by micronization is an effective strategy to overcome these problems, but conventional techniques often utilize solvents and harsh processing, which restricts their use. Newer, green technologies, such as supercritical fluid (SCF)-assisted particle formation, can produce solvent-free products under relatively mild conditions, offering many advantages over conventional methods. The antisolvent properties of the SCFs used for microparticle and nanoparticle formation have generated great interest in recent years, because the kinetics of the precipitation process and morphologies of the particles can be accurately controlled. The characteristics of the supercritical antisolvent (SAS) technique make it an ideal tool for enhancing the solubility and bioavailability of poorly water-soluble drugs. This review article focuses on SCFs and their properties, as well as the fundamentals of overcoming poorly water-soluble drug properties by micronization, crystal morphology control, and formation of composite solid dispersion nanoparticles with polymers and/or surfactants. This article also presents an overview of the main aspects of the SAS-assisted particle precipitation process, its mechanism, and parameters, as well as our own experiences, recent advances, and trends in development. Copyright © 2017 Elsevier B.V. All rights reserved.

Potential for radionuclide immobilization in the EBS/NFE: solubility limiting phases for neptunium, plutonium, and uranium

Energy Technology Data Exchange (ETDEWEB)

Rard, J. A., LLNL

1997-10-01

Retardation and dispersion in the far field of radionuclides released from the engineered barrier system/near field environment (EBS/NFE) may not be sufficient to prevent regulatory limits being exceeded at the accessible environment. Hence, a greater emphasis must be placed on retardation and/or immobilization of radionuclides in the EBS/NFE. The present document represents a survey of radionuclide-bearing solid phases that could potentially form in the EBS/NFE and immobilize radionuclides released from the waste package and significantly reduce the source term. A detailed literature search was undertaken for experimental solubilities of the oxides, hydroxides, and various salts of neptunium, plutonium, and uranium in aqueous solutions as functions of pH, temperature, and the concentrations of added electrolytes. Numerous solubility studies and reviews were identified and copies of most of the articles were acquired. However, this project was only two months in duration, and copies of some the identified solubility studies could not be obtained at short notice. The results of this survey are intended to be used to assess whether a more detailed study of identified low- solubility phase(s) is warranted, and not as a data base suitable for predicting radionuclide solubility. The results of this survey may also prove useful in a preliminary evaluation of the efficacy of incorporating chemical additives to the EBS/NFE that will enhance radionuclide immobilization.

Production and characterization of cowpea protein hydrolysate with optimum nitrogen solubility by enzymatic hydrolysis using pepsin.

Science.gov (United States)

Mune Mune, Martin Alain; Minka, Samuel René

2017-06-01

Cowpea is a source of low-cost and good nutritional quality protein for utilization in food formulations in replacement of animal proteins. Therefore it is necessary that cowpea protein exhibits good functionality, particularly protein solubility which affects the other functional properties. The objective of this study was to produce cowpea protein hydrolysate exhibiting optimum solubility by the adequate combination of hydrolysis parameters, namely time, solid/liquid ratio (SLR) and enzyme/substrate ratio (ESR), and to determine its functional properties and molecular characteristics. A Box-Behnken experimental design was used for the experiments, and a second-order polynomial to model the effects of hydrolysis time, SLR and ESR on the degree of hydrolysis and nitrogen solubility index. The optimum hydrolysis conditions of time 208.61 min, SLR 1/15 (w/w) and ESR 2.25% (w/w) yielded a nitrogen solubility of 75.71%. Protein breakdown and the peptide profile following enzymatic hydrolysis were evaluated by sodium dodecyl sulfate polyacrylamide gel electrophoresis and size exclusion chromatography. Cowpea protein hydrolysate showed higher oil absorption capacity, emulsifying activity and foaming ability compared with the concentrate. The solubility of cowpea protein hydrolysate was adequately optimized by response surface methodology, and the hydrolysate showed adequate functionality for use in food. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Assessing the solubility controls on vanadium in groundwater, northeastern San Joaquin Valley, CA

Science.gov (United States)

Wright, Michael T.; Stollenwerk, Kenneth G.; Belitz, Kenneth

2014-01-01

The solubility controls on vanadium (V) in groundwater were studied due to concerns over possible harmful health effects of ingesting V in drinking water. Vanadium concentrations in the northeastern San Joaquin Valley ranged from 25 μg/L) and lowest in samples collected from anoxic groundwater (70% 2VO4−. Adsorption/desorption reactions with mineral surfaces and associated oxide coatings were indicated as the primary solubility control of V5+ oxyanions in groundwater. Environmental data showed that V concentrations in oxic groundwater generally increased with increasing groundwater pH. However, data from adsorption isotherm experiments indicated that small variations in pH (7.4–8.2) were not likely as an important a factor as the inherent adsorption capacity of oxide assemblages coating the surface of mineral grains. In suboxic groundwater, accurate SM modeling was difficult since Eh measurements of source water were not measured in this study. Vanadium concentrations in suboxic groundwater decreased with increasing pH indicating that V may exist as an oxycationic species [e.g. V(OH)3+]. Vanadium may complex with dissolved inorganic and organic ligands under suboxic conditions, which could alter the adsorption behavior of V in groundwater. Speciation modeling did not predict the existence of V-inorganic ligand complexes and organic ligands were not collected as part of this study. More work is needed to determine processes governing V solubility under suboxic groundwater conditions. Under anoxic groundwater conditions, SM predicts that aqueous V exists as the uncharged V(OH)3 molecule. However, exceedingly low V concentrations show that V is sparingly soluble in anoxic conditions. Results indicated that V may be precipitating as V3+- or mixed V3+/Fe3+-oxides in anoxic groundwater, which is consistent with results of a previous study. The fact that V appears insoluble in anoxic (Fe reducing) redox conditions indicates that the behavior of V is different than

Serum concentrations of soluble (s)L- and (s)P-selectins in women with ovarian cancer.

Science.gov (United States)

Majchrzak-Baczmańska, Dominika B; Głowacka, Ewa; Wilczyński, Miłosz; Malinowski, Andrzej

2018-03-01

The aim of the study was to compare serum concentration of soluble L- and P-selectins in women with ovarian cancer (OC) and healthy controls, and to investigate sL- and sP-selectin levels with regard to clinical and pathological parameters. Correlation analysis was used to measure the following: sL- and sP-selectin concentration and Ca125; sP-selectin and platelet concentrations; and sL-selectin and serum leukocyte levels in women with OC. The study included 29 patients with OC and 23 healthy controls. Serum concentrations of sL- and sP-selectins were measured in all subjects. Routine diagnostic tests: CBC and USG (both groups) and Ca125 (study group) were performed. Significantly higher serum concentrations of sL- and sP-selectins were found in the study group as compared to controls. Lower levels of serum sL-selectin were observed in women with poorly-differentiated OC (G3) and advanced stages of the disease (FIGO III, IV), but the results were statistically insignificant. No statistically significant relationship was detected between sP-selectin serum concentration in women with OC and tumour differentiation, histological type, and stage of the disease. No significant correlation was found between sL- and sP-selectins and Ca125 levels. A weak correlation was found between serum concentration of sP-selectin in women with OC and platelet count. No statistically significant correlation was observed between sL-selectin concentration and serum leukocyte levels in women with OC. The analysis of sL- and sP-selectin concentrations may be a useful tool in the diagnosis of OC. The levels of sL-selectin decrease with disease progression.

Critical micelle concentration values for different surfactants measured with solid-phase microextraction fibers

NARCIS (Netherlands)

Haftka, Joris J H; Scherpenisse, Peter; Oetter, G??nter; Hodges, Geoff; Eadsforth, Charles V.; Kotthoff, Matthias; Hermens, Joop L M

The amphiphilic nature of surfactants drives the formation of micelles at the critical micelle concentration (CMC). Solid-phase microextraction (SPME) fibres were used in the present study to measure CMC values of twelve nonionic, anionic, cationic and zwitterionic surfactants. The SPME derived CMC

The Stabilization of Amorphous Zopiclone in an Amorphous Solid Dispersion.

Science.gov (United States)

Milne, Marnus; Liebenberg, Wilna; Aucamp, Marique

2015-10-01

Zopiclone is a poorly soluble psychotherapeutic agent. The aim of this study was to prepare and characterize an amorphous form of zopiclone as well as the characterization and performance of a stable amorphous solid dispersion. The amorphous form was prepared by the well-known method of quench-cooling of the melt. The solid dispersion was prepared by a solvent evaporation method of zopiclone, polyvinylpyrrolidone-25 (PVP-25), and methanol, followed by freeze-drying. The physico-chemical properties and stability of amorphous zopiclone and the solid dispersion was studied using differential scanning calorimetry (DSC), infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), hot-stage microscopy (HSM), X-ray diffractometry (XRD), solubility, and dissolution studies. The zopiclone amorphous solid-state form was determined to be a fragile glass; it was concluded that the stability of the amorphous form is influenced by both temperature and water. Exposure of amorphous zopiclone to moisture results in rapid transformation of the amorphous form to the crystalline dihydrated form. In comparison, the amorphous solid dispersion proved to be more stable with increased aqueous solubility.

Preparation of free, soluble conjugate, and insoluble-bound phenolic compounds from peels of rambutan (Nephelium lappaceum) and evaluation of antioxidant activities in vitro.

Science.gov (United States)

Sun, Liping; Zhang, Huilin; Zhuang, Yongliang

2012-02-01

The soluble phenolic compounds of rambutan peels (RP) were extracted by microwave-assisted extraction (MAE) and the operating parameters were optimized. The optimal conditions obtained were ethanol concentration of 80.85%, extraction time of 58.39 s, and the ratio of liquid to solid of 24.51:1. The soluble phenolic content by MAE was 213.76 mg GAE/g DW. The free, soluble conjugate, and insoluble-boaund phenolic compounds were prepared by alkaline hydrolysis, and the contents of 3 fractions were 185.12, 27.98 and 9.37 mg GAE/g DW, respectively. The contents of syringic acid and p-coumaric acid were high in the free fraction, showing 16.86 and 19.44 mg/g DW, and the soluble conjugate and insoluble-bound phenolics were mainly composed of gallic acid and caffeic acid. Furthermore, the antioxidant activities of 3 fractions were evaluated in 5 model systems. Results indicated that the free fraction had high antioxidant activities, compared with the soluble conjugate and insoluble-bound fractions. © 2012 Institute of Food Technologists®

Decadal-scale changes in dissolved-solids concentrations in groundwater used for public supply, Salt Lake Valley, Utah

Science.gov (United States)

Thiros, Susan A.; Spangler, Larry

2010-01-01

Basin-fill aquifers are a major source of good-quality water for public supply in many areas of the southwestern United States and have undergone increasing development as populations have grown over time. During 2005, the basin-fill aquifer in Salt Lake Valley, Utah, provided approximately 75,000 acre-feet, or about 29 percent of the total amount of water used by a population of 967,000. Groundwater in the unconsolidated basin-fill deposits that make up the aquifer occurs under unconfined and confined conditions. Water in the shallow unconfined part of the groundwater system is susceptible to near-surface contamination and generally is not used as a source of drinking water. Groundwater for public supply is withdrawn from the deeper unconfined and confined parts of the system, termed the principal aquifer, because yields generally are greater and water quality is better (including lower dissolved-solids concentrations) than in the shallower parts of the system. Much of the water in the principal aquifer is derived from recharge in the adjacent Wasatch Range (mountain-block recharge). In many areas, the principal aquifer is separated from the overlying shallow aquifer by confining layers of less permeable, fine-grained sediment that inhibit the downward movement of water and any potential contaminants from the surface. Nonetheless, under certain hydrologic conditions, human-related activities can increase dissolved-solids concentrations in the principal aquifer and result in groundwater becoming unsuitable for consumption without treatment or mixing with water having lower dissolved-solids concentrations. Dissolved-solids concentrations in areas of the principal aquifer used for public supply typically are less than 500 milligrams per liter (mg/L), the U.S. Environmental Protection Agency (EPA) secondary (nonenforceable) drinking-water standard. However, substantial increases in dissolved-solids concentrations in the principal aquifer have been documented in some

SOLUBILITIES AND PHYSICAL PROPERTIES OF SATURATED SOLUTIONS IN THE COPPER SULFATE + SULFURIC ACID + SEAWATER SYSTEM AT DIFFERENT TEMPERATURES

Directory of Open Access Journals (Sweden)

F. J. Justel

2015-09-01

Full Text Available AbstractIn Chile, the most important economic activity is mining, concentrated in the north of the country. This is a desert region with limited water resources; therefore, the mining sector requires research and identification of alternative sources of water. One alternative is seawater, which can be a substitute of the limited fresh water resources in the region. This work determines the influence of seawater on the solid-liquid equilibrium for acid solutions of copper sulfate at different temperatures (293.15 to 318.15 K, and its effect on physical properties (density, viscosity, and solubility. Knowledge of these properties and solubility data are useful in the leaching process and in the design of copper sulfate pentahydrate crystallization plants from the leaching process using seawater by means of the addition of sulfuric acid.

Increased concentrations of soluble CD40 ligand platelet in patients with primary antiphospholipidic syndrome.

Science.gov (United States)

Galicia López, Aida; Olguín Ortega, Lourdes; Saavedra, Miguel A; Méndez Cruz, René; Jimenez Flores, Rafael; García de la Peña, Maximiliano

2013-01-01

To determine the concentrations of sCD40L in patients with PAPS, and establish its association with the number of thrombosis. We included patients with PAPS and healthy controls of the same age and sex. For analysis, patients with PAPS were divided into 2 groups: 1) patients with 1 thrombosis, and 2) patients with >1 thrombosis. Soluble CD40L concentrations were determined by ELISA method. sCD40L concentrations were significantly higher in patients with PAPS compared with the controls (9.72 ng ± 11.23 ng/ml vs. 4.69 ± 4.04 ng/ml) (P=.04) There was no association between serum levels of sCD40L and the number of thrombosis (1 thrombosis: 9.81 ± 9.87 ng/ml vs 9.63 ± 12.75 ng/ml in ≥ 1thrombosis (P=.13). In women with pregnancy and abortions, (13 patients) concentrations of sCD40L were higher than in those patients without a history of abortion (26 patients) but without statically significant difference (12.11 ± 16.46 ng/ml vs. 8.80 ± 8.61 ng/ml) (P=.33). There was no correlation between levels of sCD40L and the total number of thrombosis. Patients with PAPS have higher concentrations of sCD40L compared with healthy subjects, although this is not associated with a greater number of thrombosis. Among patients with PAPS, there is a tendency to higher concentrations of sCD40L in women with pregnancy and history of abortion. Since the platelet is the main cellular source of sCD40L, is possible that this pathway plays a pathogenic role in patients with PAPS. Copyright © 2012 Elsevier España, S.L. All rights reserved.

Thermodynamics of oxygen in solid solution in vanadium and niobium--vanadium alloys

International Nuclear Information System (INIS)

Steckel, G.L.

1977-01-01

A thermodynamic study was made of the vanadium-oxygen and niobium-vanadium-oxygen systems utilizing the solid state galvanic cell technique. Investigations were made with a ThO 2 /Y 2 O 3 electrolyte over the temperature ranges 700 to 1200 0 C (973 to 1473 K) for the binary system and 650 to 1150 0 C (923 to 1423 K) for the ternary system. The activity of oxygen in vanadium obeys Henry's law for the temperatures of this investigation for concentrations up to 3.2 at. percent oxygen. For higher concentrations the activity coefficient shows positive deviations from Henry's law. The terminal solubility of oxygen in vanadium was determined. The activity of oxygen in Nb--V alloys obeys Henry's law for the temperatures of this study for oxygen concentrations less than approximately 2 at. percent. For certain Nb/V ratios Henry's law is obeyed for concentrations as high as 6.5 at. percent oxygen. First order entropy and enthalpy interaction coefficients have been determined to describe the effect on the oxygen activity of niobium additions to vanadium-rich alloys with dilute oxygen concentrations. Niobium causes relatively small decreases in the oxygen activity of V-rich alloys and increases the oxygen solubility limit. Vanadium additions to Nb-rich alloys also increases the oxygen solubility and causes substantial decreases in the dilute solution oxygen activities. The change in the thermodynamic properties when molecular oxygen dissolves in vanadium and niobium--vanadium alloys and the equilibrium oxygen pressure over the binary and ternary systems were also determined

Viscosity and Electrical Conductivity of Concentrated Solutions of Soluble Coffee

Czech Academy of Sciences Publication Activity Database

Sobolík, Václav; Žitný, R.; Tovčigrečko, Valentin; Delgado, M.; Allaf, K.

2002-01-01

Roč. 51, č. 2 (2002), s. 93-98 ISSN 0260-8774 Institutional research plan: CEZ:AV0Z4072921; CEZ:MSM 212200008 Keywords : coffee extract * soluble coffee * viscosity Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 1.085, year: 2002

Solubility of Meloxicam in Mixed Solvent Systems | Babu | Ethiopian ...

African Journals Online (AJOL)

The solubility of meloxicam is higher in phosphate buffer (pH 7.4) compared to water, probably due to ionization of the drug. The solubility of meloxicam is marginally enhanced in surfactant systems (Tween 80 and Brij 35) at concentrations higher than cmc, proving the micellar solubilization. Meloxicam solubility studies in ...

Improved intestinal absorption of a poorly water-soluble oral drug using mannitol microparticles containing a nanosolid drug dispersion.

Science.gov (United States)

Nishino, Yukiko; Kubota, Aya; Kanazawa, Takanori; Takashima, Yuuki; Ozeki, Tetsuya; Okada, Hiroaki

2012-11-01

A nozzle for a spray dryer that can prepare microparticles of water-soluble carriers containing various nanoparticles in a single step was previously developed in our laboratory. To enhance the solubility and intestinal absorption of poorly water-soluble drugs, we used probucol (PBL) as a poorly water-soluble drug, mannitol (MAN) as a water-soluble carrier for the microparticles, and EUDRAGIT (EUD) as a polymer vehicle for the solid dispersion. PBL-EUD-acetone-methanol and aqueous MAN solutions were simultaneously supplied through different liquid passages of the spray nozzle and dried together. PBL-EUD solid dispersion was nanoprecipitated in the MAN solution using an antisolvent mechanism and rapidly dried by surrounding it with MAN. PBL in the dispersion vehicle was amorphous and had higher physical stability according to powder X-ray diffraction and differential scanning calorimetry analysis. The bioavailability of PBL in PBL-EUD S-100-MAN microparticles after oral administration in rats was markedly higher (14- and 6.2-fold, respectively) than that of the original PBL powder and PBL-MAN microparticles. These results demonstrate that the composite microparticles containing a nanosized solid dispersion of a poorly water-soluble drug prepared using the spray nozzle developed by us should be useful to increase the solubility and bioavailability of drugs after oral administration. Copyright © 2012 Wiley Periodicals, Inc.

Short communication: The influence of solids concentration and bleaching agent on bleaching efficacy and flavor of sweet whey powder.

Science.gov (United States)

Jervis, M G; Smith, T J; Drake, M A

2015-04-01

Recent studies have demonstrated the effect of bleaching conditions and bleaching agent on flavor and functional properties of whey protein ingredients. Solids concentration at bleaching significantly affected bleaching efficacy and flavor effects of different bleaching agents. It is not known if these parameters influence quality of sweet whey powder (SWP). The purpose of this study was to determine the effects of solids concentration and bleaching agent on the flavor and bleaching efficacy of SWP. Colored cheddar whey was manufactured, fat separated, and pasteurized. Subsequently, the whey (6.7% solids) was bleached, concentrated using reverse osmosis (RO) to 14% solids, and then spray dried, or whey was concentrated before bleaching and then spray dried. Bleaching treatments included a control (no bleaching, 50 °C, 60 min), hydrogen peroxide (HP; 250 mg/kg, 50 °C, 60 min), benzoyl peroxide (50 mg/kg, 50 °C, 60 min), lactoperoxidase (20 mg/kg of HP, 50 °C, 30 min), and external peroxidase (MaxiBright, DSM Food Specialties, Delft, the Netherlands; 2 dairy bleaching units/mL, 50 °C, 30 min). The experiment was repeated in triplicate. Sensory properties and volatile compounds of SWP were evaluated by a trained panel and gas chromatography-mass spectrometry, respectively. Bleaching efficacy (norbixin destruction) and benzoic acid were measured by HPLC. Differences in bleaching efficacy, sensory and volatile compound profiles, and benzoic acid were observed with different bleaching agents, consistent with previous studies. Solids concentration affected bleaching efficacy of HP, but not other bleaching agents. The SWP from whey bleached with HP or lactoperoxidase following RO had increased cardboard and fatty flavors and higher concentrations of lipid oxidation compounds compared with SWP from whey bleached before RO. The SWP bleached with benzoyl peroxide after RO contained less benzoic acid than SWP from whey bleached before RO. These results indicate that

Design of modified xanthan mini-matrices for monitoring oral discharge of highly soluble Soluplus{sup ®}–glibenclamide dispersion

Energy Technology Data Exchange (ETDEWEB)

Bakshi, Paromita; Sadhukhan, Sayantan; Maiti, Sabyasachi, E-mail: sabya245@rediffmail.com

2015-09-01

In this work, Soluplus{sup ®} was used as a hydrophilic carrier for the preparation of solid dispersion (SD) of a model BCS class II drug, glibenclamide by applying hot melting process and microwave irradiation in combination. Increasing the concentration of carrier relative to drug significantly increased the drug solubility, which corresponded to a maximum 75 fold increase at a drug:carrier ratio of 1:7. Scanning electron microscopy, differential scanning calorimetry, and x-ray diffraction analyses confirmed complete amorphization of the drug in SD. In animal study, about two fold reductions in hyperglycemic level were achieved by SD compared to pure drug. SD-loaded O-carboxymethyl xanthan mini-matrices controlled the release of drug into gastro-luminal fluid over longer duration. The drug release corroborated with pH-dependent swelling behavior of the matrices and approximated anomalous diffusion mechanism. This study proved the potential of Soluplus{sup ®}-based dispersion in improving the clinical performance of the drug, especially when embedded in modified xanthan mini-matrices. - Highlights: • Microwave-induced solid dispersion of glibenclamide was prepared using Soluplus®. • Solubility of drug corresponded to 75 fold increase at a drug:Soluplus® ratio of 1:7. • Thermal and x-ray analyses suggested amorphization of drug in solid dispersion. • About two fold reductions in hyperglycemic level were achieved by solid dispersion. • Modified xanthan gum showed potential in controlling anomalous transport of drug.

Enhancement of soluble CD28 levels in the serum of Graves' disease.

Science.gov (United States)

Sun, Zhongwen; Yi, Lixian; Tao, Hong; Huang, Jingfang; Jin, Zhenghong; Xiao, Yang; Feng, Caiyun; Sun, Jing

2014-01-01

Graves' disease is an autoimmune disease of the thyroid gland mediated by T cells. CD28, a member of costimulatory molecules, plays a pivotal role in regulating T-cell responses. Plasma-soluble CD28 is one form of CD28 in peripheral blood. To investigate the concentrations of soluble CD28 in patients with Graves' disease, we used a sensitive dual monoclonal antibody sandwich enzyme-linked immunosorbent assay (ELISA) to detect the soluble form of CD28. Our results suggested that mean concentrations of soluble CD28 in plasma of patients with Graves' disease were 1.79 ±1.52 ng/ml, and levels of soluble CD28 in healthy subjects were only 0.83 ±1.35 ng/ml. Concentrations of soluble CD28 detected in patients with Graves' disease were significantly higher than those of healthy subjects (p Graves' disease. Therefore, aberrant elevation of plasma-soluble CD28 in patients with Graves' disease may reflect the dysregulation of immune system, and may serve as a useful biomarker in Graves' disease diagnosis.

Data representing two separate LC-MS methods for detection and quantification of water-soluble and fat-soluble vitamins in tears and blood serum

Directory of Open Access Journals (Sweden)

Maryam Khaksari

2017-04-01

Full Text Available Two separate liquid chromatography (LC-mass spectrometry (MS methods were developed for determination and quantification of water-soluble and fat-soluble vitamins in human tear and blood serum samples. The water-soluble vitamin method was originally developed to detect vitamins B1, B2, B3 (nicotinamide, B5, B6 (pyridoxine, B7, B9 and B12 while the fat-soluble vitamin method detected vitamins A, D3, 25(OHD3, E and K1. These methods were then validated with tear and blood serum samples. In this data in brief article, we provide details on the two LC-MS methods development, methods sensitivity, as well as precision and accuracy for determination of vitamins in human tears and blood serum. These methods were then used to determine the vitamin concentrations in infant and parent samples under a clinical study which were reported in "Determination of Water-Soluble and Fat-Soluble Vitamins in Tears and Blood Serum of Infants and Parents by Liquid Chromatography/Mass Spectrometry DOI:10.1016/j.exer.2016.12.007 [1]". This article provides more details on comparison of vitamin concentrations in the samples with the ranges reported in the literature along with the medically accepted normal ranges. The details on concentrations below the limits of detection (LOD and limits of quantification (LOQ are also discussed. Vitamin concentrations were also compared and cross-correlated with clinical data and nutritional information. Significant differences and strongly correlated data were reported in [1]. This article provides comprehensive details on the data with slight differences or slight correlations.

Data representing two separate LC-MS methods for detection and quantification of water-soluble and fat-soluble vitamins in tears and blood serum.

Science.gov (United States)

Khaksari, Maryam; Mazzoleni, Lynn R; Ruan, Chunhai; Kennedy, Robert T; Minerick, Adrienne R

2017-04-01

Two separate liquid chromatography (LC)-mass spectrometry (MS) methods were developed for determination and quantification of water-soluble and fat-soluble vitamins in human tear and blood serum samples. The water-soluble vitamin method was originally developed to detect vitamins B 1 , B 2 , B 3 (nicotinamide), B 5 , B 6 (pyridoxine), B 7 , B 9 and B 12 while the fat-soluble vitamin method detected vitamins A, D 3 , 25(OH)D 3, E and K 1 . These methods were then validated with tear and blood serum samples. In this data in brief article, we provide details on the two LC-MS methods development, methods sensitivity, as well as precision and accuracy for determination of vitamins in human tears and blood serum. These methods were then used to determine the vitamin concentrations in infant and parent samples under a clinical study which were reported in "Determination of Water-Soluble and Fat-Soluble Vitamins in Tears and Blood Serum of Infants and Parents by Liquid Chromatography/Mass Spectrometry DOI:10.1016/j.exer.2016.12.007 [1]". This article provides more details on comparison of vitamin concentrations in the samples with the ranges reported in the literature along with the medically accepted normal ranges. The details on concentrations below the limits of detection (LOD) and limits of quantification (LOQ) are also discussed. Vitamin concentrations were also compared and cross-correlated with clinical data and nutritional information. Significant differences and strongly correlated data were reported in [1]. This article provides comprehensive details on the data with slight differences or slight correlations.

Solid phase radioimmunoassays

International Nuclear Information System (INIS)

Wide, L.

1977-01-01

Solid phase coupled antibodies were introduced to facilitate the separation of bound and free labelled ligand in the competitive inhibition radioimmunoassay. Originally, the solid matrix used was in the form of small particles and since then a number of different matrices have been used such as very fine powder particles, gels, paper and plastic discs, magnetic particles and the inside surface of plastic tubes. The coupling of antibodies may be that of a covalent chemical binding, a strong physical adsorbtion, or an immunological binding to a solid phase coupled antigen. New principles of radioimmunoassay such as the solid phase sandwich techniques and the immunoradiometric assay were developped from the use of solid phase coupled antigens and antibodies. The solid phase sandwich techniques are reagent excess methods with a very wide applicability. Several of the different variants of solid phase techniques are suitable for automation. Advantages and disadvantages of solid phase radioimmunoassays when compared with those using soluble reagents are discussed. (orig.) [de

Dry season aerosol iron solubility in tropical northern Australia

Directory of Open Access Journals (Sweden)

V. H. L. Winton

2016-10-01

Full Text Available Marine nitrogen fixation is co-limited by the supply of iron (Fe and phosphorus in large regions of the global ocean. The deposition of soluble aerosol Fe can initiate nitrogen fixation and trigger toxic algal blooms in nitrate-poor tropical waters. We present dry season soluble Fe data from the Savannah Fires in the Early Dry Season (SAFIRED campaign in northern Australia that reflects coincident dust and biomass burning sources of soluble aerosol Fe. The mean soluble and total aerosol Fe concentrations were 40 and 500 ng m−3 respectively. Our results show that while biomass burning species may not be a direct source of soluble Fe, biomass burning may substantially enhance the solubility of mineral dust. We observed fractional Fe solubility up to 12 % in mixed aerosols. Thus, Fe in dust may be more soluble in the tropics compared to higher latitudes due to higher concentrations of biomass-burning-derived reactive organic species in the atmosphere. In addition, biomass-burning-derived particles can act as a surface for aerosol Fe to bind during atmospheric transport and subsequently be released to the ocean upon deposition. As the aerosol loading is dominated by biomass burning emissions over the tropical waters in the dry season, additions of biomass-burning-derived soluble Fe could have harmful consequences for initiating nitrogen-fixing toxic algal blooms. Future research is required to quantify biomass-burning-derived particle sources of soluble Fe over tropical waters.

Floating solid cellulose nanofibre nanofoams for sustained release of the poorly soluble model drug furosemide

DEFF Research Database (Denmark)

Svagan, Anna Justina; Müllertz, Anette; Löbmann, Korbinian

2017-01-01

OBJECTIVES: This study aimed to prepare a furosemide-loaded sustained release cellulose nanofibre (CNF)-based nanofoams with buoyancy. METHODS: Dry foams consisting of CNF and the model drug furosemide at concentrations of 21% and 50% (w/w) have been prepared by simply foaming a CNF-drug suspension...... followed by drying. The resulting foams were characterized towards their morphology, solid state properties and dissolution kinetics. KEY FINDINGS: Solid state analysis of the resulting drug-loaded foams revealed that the drug was present as an amorphous sodium furosemide salt and in form of furosemide...... form I crystals embedded in the CNF foam cell walls. The foams could easily be shaped and were flexible, and during the drug release study, the foam pieces remained intact and were floating on the surface due to their positive buoyancy. Both foams showed a sustained furosemide release compared...

On the use of semiempirical models of (solid + supercritical fluid) systems to determine solid sublimation properties

International Nuclear Information System (INIS)

Tabernero, Antonio; Martin del Valle, Eva M.; Galan, Miguel A.

2011-01-01

Research highlights: → We propose a method to determine sublimation properties of solids. → Low deviations were produced calculating sublimation enthalpies and pressures. → It is a required step to determine the vaporization enthalpy of the solid. → It is possible to determine solid properties using semiempirical models solid-SCF. - Abstract: Experimental solubility data of solid-supercritical fluids have significantly increased in the last few years, and semiempirical models are emerging as one of the best choices to fit this type of data. This work establishes a methodology to calculate sublimation pressures using this type of equations. It requires the use of Bartle's equation to model equilibria data solid-supercritical fluids with the aim of determining the vaporization enthalpy of the compound. Using this method, low deviations were obtained by calculating sublimation pressures and sublimation enthalpies. The values of the sublimation pressures were subsequently used to successfully model different multiphasic equilibria, as solid-supercritical fluids and solid-solvent-supercritical fluids with the Peng-Robinson equation of state (without considering the sublimation pressure as an adjustable parameter). On the other hand, the sublimation pressures were also used to calculate solid sublimation properties and acetaminophen solvation properties in some solvents. Also, solubility data solid-supercritical fluids from 62 pharmaceuticals were fitted with different semiempirical equations (Chrastil, Kumar-Johnston and Bartle models) in order to present the values of solvation enthalpies in sc-CO 2 and vaporization enthalpies for these compounds. All of these results highlight that semiempirical models can be used for any other purpose as well as modeling (solid + supercritical fluids) equilibria.

Preparation, characterization and solubility product constant of AmOHCO3

International Nuclear Information System (INIS)

Silva, R.J.

1985-01-01

An investigation into the nature and solubility of a stable solid phase formed by a trivalent actinide, 243 Am 3+ , in dilute aqueous carbonate solutions was conducted. The compound exhibited an x-ray powder diffraction pattern which was nearly identical to that reported for NdOHCO 3 - type A. The pattern could be indexed in the orthorhombic system with unit cell parameters a = 4.958, b = 8.487, and c = 7.215 A. The steady-state solubility of the compound was determined from the results of both dissolution and precipitation experiments. The average solubility product quotient for 0.1M ionic strength, 25 +- 1 0 C and 1 atmosphere pressure was found to be 583 +- 206. The solubility product constant for zero ionic strength was estimated to be 335 +- 120. 22 references, 3 tables

A data reconnaissance on the effect of suspended-sediment concentrations on dissolved-solids concentrations in rivers and tributaries in the Upper Colorado River Basin

Science.gov (United States)

Tillman, Fred D.; Anning, David W.

2014-01-01

The Colorado River is one of the most important sources of water in the western United States, supplying water to over 35 million people in the U.S. and 3 million people in Mexico. High dissolved-solids loading to the River and tributaries are derived primarily from geologic material deposited in inland seas in the mid-to-late Cretaceous Period, but this loading may be increased by human activities. High dissolved solids in the River causes substantial damages to users, primarily in reduced agricultural crop yields and corrosion. The Colorado River Basin Salinity Control Program was created to manage dissolved-solids loading to the River and has focused primarily on reducing irrigation-related loading from agricultural areas. This work presents a reconnaissance of existing data from sites in the Upper Colorado River Basin (UCRB) in order to highlight areas where suspended-sediment control measures may be useful in reducing dissolved-solids concentrations. Multiple linear regression was used on data from 164 sites in the UCRB to develop dissolved-solids models that include combinations of explanatory variables of suspended sediment, flow, and time. Results from the partial t-test, overall likelihood ratio, and partial likelihood ratio on the models were used to group the sites into categories of strong, moderate, weak, and no-evidence of a relation between suspended-sediment and dissolved-solids concentrations. Results show 68 sites have strong or moderate evidence of a relation, with drainage areas for many of these sites composed of a large percentage of clastic sedimentary rocks. These results could assist water managers in the region in directing field-scale evaluation of suspended-sediment control measures to reduce UCRB dissolved-solids loading.

Enhancement of solubility and dissolution rate of atorvastatin ...

African Journals Online (AJOL)

Purpose: To investigate the formation of atorvastatin calcium (AC) co-crystal to improve its solubility and dissolution rate. Method: Co-crystallization of AC in equimolar ratio with isonicotinamide (INA) was carried out by slow solvent evaporation method using methanol. The solid obtained was characterized by powder x-ray ...

Thermodynamic properties of chemical species in nuclear waste: Topical report: The solubilities of crystalline neodymium and americium trihydroxides

International Nuclear Information System (INIS)

Silva, R.J.

1982-12-01

The solubilities of crystalline Nd(OH) 3 and Am(OH) 3 were measured at 25 +- 1 0 C in aqueous solutions of 0.1 M NaClO 4 under argon as a function of pH by determination of the solution concentrations of Nd and Am. Prior to use in the solubility measurements, the solid materials were characterized through their x-ray powder patterns. Analyses of the solubility data with the computer code MINEQL allowed estimates of the solubility product constants, K/sub s10/, and the second and third hydrolysis constants, K 12 and K 13 , for Nd 3+ and Am 3+ . Upper limits for the fourth hydrolysis constants were also estimated. For Nd, they are: log K/sub s10/ = 16.0 +- .2, log K 12 = -15.8 +- .5, log K 13 = -23.9 +- .2 and log K 14 12 = -16.0 +- .7, log K 13 = -24.3 +- .3 and log K 14 3 was found to be a factor of 100 to 300 less soluble than predicted from previously reported thermodynamic data over much of the pH range of environmental interest. The measured solubility of crystalline Am(OH) 3 was also considerably less than predicted from the previously estimated solubility product constant, i.e., a factor of about 600. For Am, the solubility of the crystalline material was a factor of about 30 less than the amorphous material. The solubilities of crystalline Nd(OH) 3 and Am(OH) 3 as a function of pH were found to be very similar and Nd(OH) 3 should be a good analog compound for Am(OH) 3

Thorium oxalate solubility and morphology

International Nuclear Information System (INIS)

Monson, P.R. Jr.; Hall, R.

1981-10-01

Thorium was used as a stand-in for studying the solubility and precipitation of neptunium and plutonium oxalates. Thorium oxalate solubility was determined over a range of 0.001 to 10.0 in the concentration parameter [H 2 C 2 O 4 ]/[HNO 3 ] 2 . Morphology of thorium oxide made from the oxalate precipitates was characterized by scanning electron microscopy. The different morphologies found for oxalate-lean and oxalate-rich precipitations were in agreement with predictions based on precipitation theory

Successive membrane separation processes simplify concentration of lipases produced by Aspergillus niger by solid-state fermentation.

Science.gov (United States)

Reinehr, Christian Oliveira; Treichel, Helen; Tres, Marcus Vinicius; Steffens, Juliana; Brião, Vandré Barbosa; Colla, Luciane Maria

2017-06-01

In this study, we developed a simplified method for producing, separating, and concentrating lipases derived from solid-state fermentation of agro-industrial residues by filamentous fungi. First, we used Aspergillus niger to produce lipases with hydrolytic activity. We analyzed the separation and concentration of enzymes using membrane separation processes. The sequential use of microfiltration and ultrafiltration processes made it possible to obtain concentrates with enzymatic activities much higher than those in the initial extract. The permeate flux was higher than 60 L/m 2 h during microfiltration using 20- and 0.45-µm membranes and during ultrafiltration using 100- and 50-kDa membranes, where fouling was reversible during the filtration steps, thereby indicating that the fouling may be removed by cleaning processes. These results demonstrate the feasibility of lipase production using A. niger by solid-state fermentation of agro-industrial residues, followed by successive tangential filtration with membranes, which simplify the separation and concentration steps that are typically required in downstream processes.

Solubility measurement of iron-selenium compounds under reducing conditions. Research document

International Nuclear Information System (INIS)

Kitamura, Akira; Shibata, Masahiro

2003-03-01

Chemical behavior of selenium (Se), which was one of the important elements for performance assessment of geological disposal of high-level radioactive waste, was investigated under reducing and iron-containing conditions. A washing method for an iron diselenide (FeSe 2 (cr)) reagent with acidic and basic solutions (0.1 and 1 M HCl and 1 M NaOH) was carried out for the purification of FeSe 2 reagent, which was considered to be a solubility limiting solid for Se under the geological disposal conditions. Furthermore, solubility of FeSe 2 (cr) was measured in alkaline solution (pH: 11 - 13) under reducing conditions (E h vs SHE: -0.4 - 0 V), and thermodynamic data on equilibrium reactions between Se in solution and Se precipitate were obtained. The dependencies of solubility values on pH and redox potential (E h : vs. standard hydrogen electrode) were best interpreted that the solubility limiting solid was not FeSe 2 (cr) but Se(cr) and the aqueous species was SeO 3 2- in the present experimental conditions. The equilibrium constant between Se(cr) and SeO 3 2- at zero ionic strength was determined and compared with literature values. The chemical behavior of Se under geological disposal conditions was discussed. (author)

Solid-state characterization of the HIV protease inhibitor

CERN Document Server

Kim, Y A

2002-01-01

The LB71350, (3S, 4R)-Epoxy-(5S)-[[N-(1-methylethoxy) carbonyl]-3-(methylsulfonyl)-L-valinyl]amin= o]-N-[2-methyl-(1R)-[(phenyl)carbonyl]propyl-6-phenylhexanamide, is a novel HIV protease inhibitor. Its equilibrium solubility at room temperature was less than 40 mu g/mL. It was speculated that the low aqueous solubility might be due to the high crystalline lattice energy resulting from intermolecular hydrogen bonds. The present study was carried out to learn the solid-state characteristics of LB71350 using analytical methods such as NMR, FT-IR and XRD. sup 1 sup 3 C Solid-state NMR, solution NMR, and FT-IR spectra of the various solid forms of LB71350 were used to identify the conformation and structure of the solid forms. The chemical shifts of sup 1 sup 3 C solid-state NMR spectra suggest that the crystalline form might have 3 intermolecular hydrogen bondings between monomers.

Nondestructive quantification of the soluble-solids content and the available acidity of apples by Fourier-transform near-infrared spectroscopy

Science.gov (United States)

Ying, Yibin; Liu, Yande; Tao, Yang

2005-09-01

This research evaluated the feasibility of using Fourier-transform near-infrared (FT-NIR) spectroscopy to quantify the soluble-solids content (SSC) and the available acidity (VA) in intact apples. Partial least-squares calibration models, obtained from several preprocessing techniques (smoothing, derivative, etc.) in several wave-number ranges were compared. The best models were obtained with the high coefficient determination (r) 0.940 for the SSC and a moderate r of 0.801 for the VA, root-mean-square errors of prediction of 0.272% and 0.053%, and root-mean-square errors of calibration of 0.261% and 0.046%, respectively. The results indicate that the FT-NIR spectroscopy yields good predictions of the SSC and also showed the feasibility of using it to predict the VA of apples.

Nondestructive quantification of the soluble-solids content and the available acidity of apples by Fourier-transform near-infrared spectroscopy

International Nuclear Information System (INIS)

Ying Yibin; Liu Yande; Tao Yang

2005-01-01

This research evaluated the feasibility of using Fourier-transform near-infrared (FT-NIR) spectroscopy to quantify the soluble-solids content (SSC) and the available acidity (VA) in intact apples. Partial least-squares calibration models, obtained from several preprocessing techniques (smoothing, derivative, etc.) in several wave-number ranges were compared. The best models were obtained with the high coefficient determination (r 2 ) 0.940 for the SSC and a moderate r 2 of 0.801 for the VA, root-mean-square errors of prediction of 0.272% and 0.053%, and root-mean-square errors of calibration of 0.261% and 0.046%, respectively. The results indicate that the FT-NIR spectroscopy yields good predictions of the SSC and also showed the feasibility of using it to predict the VA of apples

Effect of the hydrogen concentration on the ductility of Zry-4

International Nuclear Information System (INIS)

Domizzi, G.; Ovejero Garcia, J.

1996-01-01

After many years in service, zirconium alloys employed in nuclear reactors may reach high contents of hydride particles, exceeding the hydrogen solid solubility at the service temperature. The brittle character of zirconium hydride promotes the alloy embrittlement. In order to predict the critical hydrogen concentration which causes a ductile-brittle transition in a Zry-4 foil, 0.02mm thick, tensile test specimens were hydride by gaseous charging. To obtain uniform hydride distribution the specimens were electroplated with a film of copper prior to gaseous charge. In absence of oxide film, the foils retained its ductility up to high hydrogen concentration (950 Og/g). The critical hydrogen concentration was attained at 2900-3100 Og/g. (author). 4 refs., 2 figs., 1 tab

Acute and Chronic Toxicity of Soluble Fractions of Industrial Solid Wastes on Daphnia magna and Vibrio fischeri

Directory of Open Access Journals (Sweden)

Letícia Flohr

2012-01-01

Full Text Available Industrial wastes may produce leachates that can contaminate the aquatic ecosystem. Toxicity testing in acute and chronic levels is essential to assess environmental risks from the soluble fractions of these wastes, since only chemical analysis may not be adequate to classify the hazard of an industrial waste. In this study, ten samples of solid wastes from textile, metal-mechanic, and pulp and paper industries were analyzed by acute and chronic toxicity tests with Daphnia magna and Vibrio fischeri. A metal-mechanic waste (sample MM3 induced the highest toxicity level to Daphnia magna(CE50,48 h=2.21%. A textile waste induced the highest toxicity level to Vibrio fischeri (sample TX2, CE50,30 min=12.08%. All samples of pulp and paper wastes, and a textile waste (sample TX2 induced chronic effects on reproduction, length, and longevity of Daphnia magna. These results could serve as an alert about the environmental risks of an inadequate waste classification method.

Water resources and effects of potential surface coal mining on dissolved solids in Hanging Woman Creek basin, southeastern Montana

Science.gov (United States)

Cannon, M.R.

1989-01-01

Groundwater resources of the Hanging Woman Creek basin, Montana include Holocene and Pleistocene alluvial aquifers and sandstone , coal, and clinker aquifers in the Paleocene Fort Union Formation. Surface water resources are composed of Hanging Woman Creek, its tributaries, and small stock ponds. Dissolved-solids concentrations in groundwater ranged from 200 to 11,00 mg/L. Generally, concentrations were largest in alluvial aquifers and smallest in clinker aquifers. Near its mouth, Hanging Woman Creek had a median concentration of about 1,800 mg/L. Mining of the 20-foot to 35-foot-thick Anderson coal bed and 3-foot to 16-foot thick Dietz coal bed could increase dissolved-solids concentrations in shallow aquifers and in Hanging Woman Creek because of leaching of soluble minerals from mine spoils. Analysis of saturated-paste extracts from 158 overburden samples indicated that water moving through mine spoils would have a median increase in dissolved-solids concentration of about 3,700 mg/L, resulting in an additional dissolved-solids load to Hanging Woman Creek of about 3.0 tons/day. Hanging Woman Creek near Birney could have an annual post-mining dissolved-solids load of 3,415 tons at median discharge, a 47% increase from pre-mining conditions load. Post-mining concentrations of dissolved solids, at median discharge, could range from 2,380 mg/L in March to 3,940 mg/L in August, compared to mean pre-mining concentrations that ranged from 1,700 mg/L in July, November, and December to 2,060 mg/L in May. Post-mining concentrations and loads in Hanging Woman Creek would be smaller if a smaller area were mined. (USGS)

Novel Nanostructured Solid Materials for Modulating Oral Drug Delivery from Solid-State Lipid-Based Drug Delivery Systems.

Science.gov (United States)

Dening, Tahnee J; Rao, Shasha; Thomas, Nicky; Prestidge, Clive A

2016-01-01

Lipid-based drug delivery systems (LBDDS) have gained significant attention in recent times, owing to their ability to overcome the challenges limiting the oral delivery of poorly water-soluble drugs. Despite the successful commercialization of several LBDDS products over the years, a large discrepancy exists between the number of poorly water-soluble drugs displaying suboptimal in vivo performances and the application of LBDDS to mitigate their various delivery challenges. Conventional LBDDS, including lipid solutions and suspensions, emulsions, and self-emulsifying formulations, suffer from various drawbacks limiting their widespread use and commercialization. Accordingly, solid-state LBDDS, fabricated by adsorbing LBDDS onto a chemically inert solid carrier material, have attracted substantial interest as a viable means of stabilizing LBDDS whilst eliminating some of the various limitations. This review describes the impact of solid carrier choice on LBDDS performance and highlights the importance of appropriate solid carrier material selection when designing hybrid solid-state LBDDS. Specifically, emphasis is placed on discussing the ability of the specific solid carrier to modulate drug release, control lipase action and lipid digestion, and enhance biopharmaceutical performance above the original liquid-state LBDDS. To encourage the interested reader to consider their solid carrier choice on a higher level, various novel materials with the potential for future use as solid carriers for LBDDS are described. This review is highly significant in guiding future research directions in the solid-state LBDDS field and fostering the translation of these delivery systems to the pharmaceutical marketplace.

Development of novel sibutramine base-loaded solid dispersion with gelatin and HPMC: physicochemical characterization and pharmacokinetics in beagle dogs.

Science.gov (United States)

Lim, Hyun-Tae; Balakrishnan, Prabagar; Oh, Dong Hoon; Joe, Kwan Hyung; Kim, Young Ran; Hwang, Doo Hyung; Lee, Yong-Bok; Yong, Chul Soon; Choi, Han-Gon

2010-09-15

To develop a novel sibutramine base-loaded solid dispersion with enhanced solubility and bioavailability, various solid dispersions were prepared using a spray drying technique with hydrophilic polymers such as gelatin, HPMC and citric acid. Their solubility, thermal characteristics and crystallinity were investigated. The dissolution and pharmacokinetics of the sibutramine base-loaded solid dispersion were then compared with a sibutramine hydrochloride monohydrate-loaded commercial product (Reductil). The solid dispersions prepared with gelatin gave higher drug solubility than those prepared without gelatin, irrespective of the amount of polymer. The sibutramine base-loaded solid dispersions containing hydrophilic polymer and citric acid showed higher drug solubility compared to sibutramine base and sibutramine hydrochloride monohydrate. Among the formulations tested, the solid dispersion composed of sibutramine base/gelatin/HPMC/citric acid at the weight ratio of 1/0.8/0.2/0.5 gave the highest solubility of 5.03+/-0.24 mg/ml. Our DSC and powder X-ray diffraction results showed that the drug was present in an altered amorphous form in this solid dispersion. The difference factor (f(1)) values between solid dispersion and commercial product were 2.82, 6.65 and 6.31 at pH 1.2, 4.0 and 6.8, respectively. Furthermore, they had the similarity factor (f(2)) value of 65.68, 53.43 and 58.97 at pH 1.2, 4.0 and 6.8, respectively. Our results suggested that the solid dispersion and commercial product produced a similar correlation of dissolution profiles at all pH ranges. The AUC, C(max) and T(max) of the parent drug and metabolite I and II from the solid dispersion were not significantly different from those of the commercial product, suggesting that the solid dispersion might be bioequivalent to the commercial product in beagle dogs. Thus, the sibutramine base-loaded solid dispersion prepared with gelatin, HPMC and citric acid is a promising candidate for improving the

Ab initio identified design principles of solid-solution strengthening in Al

International Nuclear Information System (INIS)

Ma Duancheng; Friák, Martin; Pezold, Johann von; Raabe, Dierk; Neugebauer, Jörg

2013-01-01

Solid-solution strengthening in six Al–X binary systems is investigated using first-principle methods. The volumetric mismatch parameter and the solubility enthalpy per solute were calculated. We derive three rules for designing solid-solution strengthened alloys: (i) the solubility enthalpy per solute is related to the volumetric mismatch by a power law; (ii) for each annealing temperature, there exists an optimal solute–volume mismatch to achieve maximum strength; and (iii) the strengthening potential of high volumetric mismatch solutes is severely limited by their low solubility. Our results thus show that the thermodynamic properties of the system (here Al–X alloys) set clear upper bounds to the achievable strengthening effects owing to the reduced solubility with increasing volume mismatch. (paper)

Generalization of the Nernst-Einstein equation for self-diffusion in high-defect-concentration solids

International Nuclear Information System (INIS)

McKee, R.A.

1981-01-01

It is shown that the Nernst-Einstein equation can be generalized for a high defect concentration solid to relate the mobility or conductivity to the self-diffusion coefficient. This relationship is derived assuming that the diffusing particles interact strongly and that the mobility is concentration-dependent. It is derived for interstitial disordered structures, but it is perfectly general to any mechanism of self diffusion as long as diffusion in a pure system is considered

Solubility of sulfur in Fe-Cr-Ni alloys

International Nuclear Information System (INIS)

Bogolyubskij, S.D.; Petrova, E.F.; Rogov, A.I.; Shvartsman, L.A.

1979-01-01

The solubility of 35 S was determined in Fe-Cr-Ni alloys in the range of temperatures between 910 and 1050 deg C by the method of radiometric analysis. It was found that the solubility of sulfur increases with the concentration of chromium in alloys with 20% Ni

Vapor equilibrium data for the systems Ar--N/sub 2/, Kr--Ar, Kr--N/sub 2/, and Xe--Kr, as well as the liquidus lines of solid xenon and of solid krypton in liquid air component mixtures

Energy Technology Data Exchange (ETDEWEB)

Mastera, S J

1977-01-15

The knowledge of vapor-liquid equilibrium data of real gas mixtures makes possible a precise design of a low temperature distillation system. The noble gas isotopes Kr and Xe are formed as a result of nuclear fission. They reach the off-gas, where they must be separated by cryogenic methods, among others, in order to reduce radiological contamination of the environment. Consequently, an equilibrium apparatus was constructed inhouse, which worked according to a dynamical measurement method. The following low temperature measurements were performed with this apparatus: (1) to test the apparatus with the Ar--N/sub 2/ system, at temperatures of 80, 85, 90, 95, and 100 degrees K; (2) with the Kr--Ar system, at temperatures of 115, 116.5, 120, and 125 degrees K; (3) with the Kr--N/sub 2/ system, at temperatures of 100, 105, at 110 degrees K in the N/sub 2/-rich existence range of the liquid phase above the solubility limit, and at temperatures of 115, 120, and 125 degrees K in the entire concentration range. No data at all were previously known about this important system. (4) In the Xe-Kr system, at temperatures of 150, 155, and 160 degrees K, in the Kr-rich liquid existence range above the solubility limit, and at the temperature steps 165, 166, and 170 degrees in the entire concentration range. The consistency of the equilibrium data thus determined was tested with the computer program SYMFIT. These measurements were completed by determining the solubility limits (= liquidus lines) of solid Kr in a liquid Kr--Ar mixture or in a liquid Kr--N/sub 2/ mixture, as well as the solubility limit of solid Xe in a liquid Xe--Kr mixture. The measurement points for the liquidus lines were associated with the respective pressure and respective temperature over the entire concentration range. The experimentally determined data are displayed on tables and graphs. The utilized measurement equipment, with its glass equilibrium cell, is described.

FACT light collection - solid light concentrators in Cherenkov Astronomy

Energy Technology Data Exchange (ETDEWEB)

Braun, Isabel [ETH Zurich, Institute for Particle Physics, CH-8093 Zurich (Switzerland); Collaboration: FACT-Collaboration

2011-07-01

Pixelized cameras of Imaging Atmospheric Cherenkov Telescopes use hollow light guides with reflective surfaces based on the Winston cone design. These cones minimize insensitive spaces between the photo sensors and shield the camera from stray background light by limiting the angular acceptance to the primary reflector area. FACT (First G-APD Cherenkov Telescope) will be the first IACT with Geiger-mode avalanche photodiodes as light sensors. Solid light concentrators complementing these sensors will be used instead of hollow Winston cones. We will present simulations and measurements of our light collector design, which was optimized for the requirements of the FACT telescope and detector, and discuss the specific differences to more traditional solutions.

Distribution of Total Suspended Solids Concentration in a River

Directory of Open Access Journals (Sweden)

Ahmad Hanif Asyhar

2012-08-01

Full Text Available Disposal of either industrial or nonindustrial wastewater into a river has a potential to cause riverpollution. Because each load of wastewater discharged into a river contains physical, chemical, and biological parametersthat determine water quality, so that it can affect the dissolved oxygen concentration in a river. Therefore the conductedresearch was aimed to determine the pattern of pollutant dispersion in Surabaya River within the section that is closed tothe Karang Pilang Monitoring Station - Surabaya. Parameter used in this research was Total Suspended Solids (TSS. Themethod used was the finite volume method with Quadratic Upwind Interpolation Convective Kinematics (QUICK schemeby means of developing models of dispersion water pollutants in a river. The governing equation was controlled by the lawsof mass conservation, momentum conservation, and pollution transport equation. Further, these equations were solvedusing numerical calculation and followed by numerical simulation. From the numerical simulation results, it can beconcluded that the magnitude of pollutant dispersion is determined by the initial discharged TSS concentrations into theriver, however the longitudinal direction is more dominantly influenced than in lateral directions.

Investigation of Rheological Impacts on the Defense Waste Processing Facility's Sludge Slurry Feed as Insoluble Solids and Wash Endpoints are Adjusted

International Nuclear Information System (INIS)

Fellinger, T. L.; Howard, S.J.; Lee, M.C.; Galloway, R.H.

2006-01-01

The Savannah River Site (SRS) is currently pursuing an aggressive program to empty its High Level Waste (HLW) tanks and immobilize its radioactive waste into a durable borosilicate glass in the Defense Waste Processing Facility (DWPF). To create a batch of feed for the DWPF, several tanks of radioactive sludge slurry are combined into one of the million gallon (i.e. 3.79 E06 liters) feed tanks for DWPF. Once these sludge slurries are combined, the soluble sodium and weight percent total solids are adjusted by a 'washing' process. The 'washing' process involves diluting the soluble sodium of the sludge slurry with inhibited water (0.015 M NaOH and 0.015 M NaNO 2 ) and allowing the sludge slurry to settle into two layers. The two layers in the tank consist of a clear supernate on top and a layer of settled sludge solids on the bottom. The clear supernate layer is then decanted to another hold tank. This 'washing' process is repeated until the desired wash endpoint (i.e. sodium concentration in the supernate) and weight percent total solids are achieved. A final washed batch of feed consists of approximately 500,000 gallons (i.e. 1.89 E06 liters). DWPF has already processed three batches of feed and is currently processing a fourth. Prior to processing a batch of feed in the DWPF, it must be well characterized. Samples of the prepared feed batch are sent to the Savannah River National Laboratory (SRNL) for this characterization. As a part of the SRNL characterization for the fourth batch, rheology measurements were performed. Measurements were performed at different weight percent insoluble solids loadings to mimic potential facility processing scenarios (i.e. mixing/pumping of concentrated sludge slurry). In order to determine the influence of the soluble Na on the rheological properties of the sample, the supernate of the 'as received' sample was adjusted from 1 M soluble Na to 0.5 M soluble Na by using a lab scale version of the 'washing' process. Rheology

Simple multipurpose apparatus for solubility measurement of solid solutes in liquids

DEFF Research Database (Denmark)

Malwade, Chandrakant Ramkrishna; Christensen, Lars Porskjær

2016-01-01

students of chemical engineering program at University of Southern Denmark. The exercises included solubility measurement and cooling crystallization of salicylic acid from five different organic solvents and extraction of artemisinin from the leaves of the plant Artemisia annua by using different solvents...

Impact of Dendrimers on Solubility of Hydrophobic Drug Molecules

Directory of Open Access Journals (Sweden)

Sonam Choudhary

2017-05-01

Full Text Available Adequate aqueous solubility has been one of the desired properties while selecting drug molecules and other bio-actives for product development. Often solubility of a drug determines its pharmaceutical and therapeutic performance. Majority of newly synthesized drug molecules fail or are rejected during the early phases of drug discovery and development due to their limited solubility. Sufficient permeability, aqueous solubility and physicochemical stability of the drug are important for achieving adequate bioavailability and therapeutic outcome. A number of different approaches including co-solvency, micellar solubilization, micronization, pH adjustment, chemical modification, and solid dispersion have been explored toward improving the solubility of various poorly aqueous-soluble drugs. Dendrimers, a new class of polymers, possess great potential for drug solubility improvement, by virtue of their unique properties. These hyper-branched, mono-dispersed molecules have the distinct ability to bind the drug molecules on periphery as well as to encapsulate these molecules within the dendritic structure. There are numerous reported studies which have successfully used dendrimers to enhance the solubilization of poorly soluble drugs. These promising outcomes have encouraged the researchers to design, synthesize, and evaluate various dendritic polymers for their use in drug delivery and product development. This review will discuss the aspects and role of dendrimers in the solubility enhancement of poorly soluble drugs. The review will also highlight the important and relevant properties of dendrimers which contribute toward drug solubilization. Finally, hydrophobic drugs which have been explored for dendrimer assisted solubilization, and the current marketing status of dendrimers will be discussed.

Solubility of nicotinic acid in water, ethanol, acetone, diethyl ether, acetonitrile, and dimethyl sulfoxide

International Nuclear Information System (INIS)

Gonçalves, Elsa M.; Minas da Piedade, Manuel E.

2012-01-01

Highlights: ► We determined the solubility of nicotinic acid in six solvents by the gravimetric method. ► We found that, regardless of the solvent, the same monoclinic solid phase was in equilibrium with the solution. ► We determined the activity coefficients of nicotinic acid in the six solvents. ► We found that the solubility trends seem to be determined by the polarity and polarizability of the solvent. - Abstract: The mole fraction equilibrium solubility of nicotinic acid in six solvents (water, ethanol, dimethyl sulfoxide, acetone, acetonitrile and diethyl ether) differing in polarity, polarizability, and hydrogen-bonding ability, was determined over the temperature range (283 to 333) K, using the gravimetric method. The results obtained led to the solubility order dimethyl sulfoxide (DMSO) ≫ ethanol > water > acetone > diethyl ether > acetonitrile. An analysis based on various solvent descriptors, indicated that this trend seems to be mainly determined by the polarity and polarizability of the solvent. The activity coefficients of nicotinic acid in the different solvents, under saturation conditions, were determined as a function of the temperature and it was found that DMSO exhibits enhanced solubility relative to an ideal solution while the opposite is observed for all other solvents. Both the solvent and the fact that nicotinic acid is primarily zwitterionic in aqueous solution and non-zwitterionic in non-aqueous media, did not affect the nature of the solid phases in equilibrium with the different solutions. Indeed, X-ray powder diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, and differential scanning calorimetry analysis indicated that, despite some differences in particle size and morphology, the starting material and the solid products obtained at the end of the solubility studies in the six solvents used in this work were all crystalline and corresponded to the same monoclinic phase.

High Concentration of Serum Soluble Fas in Patients with Head and Neck Carcinoma: A Comparative Study Before and After Surgical Removal of Tumor

OpenAIRE

Seyed Basir Hashemi; Mohammad Javad Fattahi; Mansooreh Jaberipour; Mojtaba Habibagahi; Mahmood Shariati

2010-01-01

Background:Alternative splicing of the Fas transcript can produce a naturalsecreted isoform of this molecule. Some cancer cells can also produce soluble Fas (sFas)which may have suppressive effects on the immune system's anti-tumor response.Elevated concentrations of sFas have been detected in the sera of patients with differentmalignancies. Materials and Methods:The concentrations of sFas in sera of patients with headand neck carcinoma (HNC, n=98) and healthy individuals (n=30) were measured...

Studies on the optimum conditions for the extraction and concentration of roselle (Hibiscus sabdariffa Linn. extract

Directory of Open Access Journals (Sweden)

Arunporn Itharat2

2008-04-01

Full Text Available The present study aimed to: (a study the physical and chemical properties of fresh roselle calyxes; (b study the optimum conditions for water extraction of roselle; and (e compare the methods of evaporation (vacuum, atmospheric for processing of concentrated roselle extract. This study found that the L*, a* and b* values of fresh roselle calyxes were 0.09±0.01, 0.02±0.01 and 0.05±0.01. The pH, total acidity and total soluble solids content were 2.16±0.05, 4.20±0.01% as malic acid and 5.83±0.04°Brix, respectively. The yields of fresh and dried roselle calyxes production were 47.45±0.71% and 9.58±0.77%. The optimum conditions for fresh roselle calyxes, fresh calyxes to water ratio was 1:2, with the extraction temperature of 50oC for 30 min. For dried roselle calyxes, the optimum conditions were 1:10 ratio of dried calyxes to water and the extraction temperature of 50oC for 30 min. The method of evaporation under the vacuum of 44 cmHg at 70oC was an appropriate selected method for both concentrated fresh and dried roselle extracts. The pH, total acidity and total soluble solids contents of concentrated fresh roselle extract were 2.77±0.02, 12.73±0.09% as malic acid and 25.07±0.10 oBrix, respectively. The total anthocyanin, total phenolic contents and EC50 (DPPH radical scavenging assay were 37.67± 0.02 mg/100 g fresh roselle calyxes, 31.26±0.75 mg gallic acid/g and 39.37±0.61 mg/ml (n=9. The pH, total acidity and total soluble solids contents of concentrated dried roselle extract were 2.89±0.05, 11.96±0.34% as malic acid and 25.07±0.10 oBrix. The total anthocyanin, total phenolic contents and EC50 were 340.97±0.15 mg/100 g dried roselle calyxes, 31.18± 0.62 mg gallic acid/g and 47.53±0.85 mg/ml (n=9, respectively.

Solubility of heavy metals added to MSW

International Nuclear Information System (INIS)

Lo, H.M.; Lin, K.C.; Liu, M.H.; Pai, T.Z.; Lin, C.Y.; Liu, W.F.; Fang, G.C.; Lu, C.; Chiang, C.F.; Wang, S.C.; Chen, P.H.; Chen, J.K.; Chiu, H.Y.; Wu, K.C.

2009-01-01

This paper aims to investigate the six heavy metal levels (Cd, Cr, Cu, Pb, Ni and Zn) in municipal solid waste (MSW) at different pHs. It intends to provide the baseline information of metals solubility in MSW co-disposed or co-digested with MSW incinerator ashes in landfill or anaerobic bioreactors or heavy metals contaminated in anaerobic digesters. One milliliter (equal to 1 mg) of each metal was added to the 100 ml MSW and the batch reactor test was carried out. The results showed that higher HNO 3 and NaOH were consumed at extreme pH of 1 and 13 compared to those from pH 2 to 11 due to the comparably higher buffer capacity. Pb was found to have the least soluble level, highest metal adsorption (%) and highest partitioning K d (l g -1 ) between pH 3 and 12. In contrast, Ni showed the highest soluble level, lowest metal adsorption (%) and lowest K d (l g -1 ) between pH 4 and 12. Except Ni and Cr, other four metals seemed to show the amphibious properties as comparative higher solubility was found in the acidic and basic conditions

Solubility of heavy metals added to MSW

Energy Technology Data Exchange (ETDEWEB)

Lo, H.M. [Department of Environmental Engineering and Management, Chaoyang University of Technology, 168 Gifong E. Road, Wufong, Taichung County 41349, Taiwan (China)], E-mail: hmlo@cyut.edu.tw; Lin, K.C. [Department of Occupational Safety and Health, Chung Shan Medical University, 110, Sec. 1, Jiangguo N. Rd., Taichung 402, Taiwan (China); Liu, M.H.; Pai, T.Z. [Department of Environmental Engineering and Management, Chaoyang University of Technology, 168 Gifong E. Road, Wufong, Taichung County 41349, Taiwan (China); Lin, C.Y. [Department of Soil and Water Conservation, Chung Hsing University, 250 Kuokuang Road, Taichung 402, Taiwan (China); Liu, W.F. [Department of Electronical Engineering, Feng Chia University, 100 Wenhwa Road, Taichung 407, Taiwan (China); Fang, G.C. [Department of Environmental Engineering, Hungkuang University, 34 Chung-Chie Road, Sha Lu, Taichung 433, Taiwan (China); Lu, C. [Department of Environmental Engineering, Chung Hsing University, 250 Kuokuang Road, Taichung 402, Taiwan (China); Chiang, C.F. [Department of Health Risk Management, China Medical University, No. 91 Hsueh-Shih Road, Taichung 40402, Taiwan (China); Wang, S.C.; Chen, P.H.; Chen, J.K.; Chiu, H.Y.; Wu, K.C. [Department of Environmental Engineering and Management, Chaoyang University of Technology, 168 Gifong E. Road, Wufong, Taichung County 41349, Taiwan (China)

2009-01-15

This paper aims to investigate the six heavy metal levels (Cd, Cr, Cu, Pb, Ni and Zn) in municipal solid waste (MSW) at different pHs. It intends to provide the baseline information of metals solubility in MSW co-disposed or co-digested with MSW incinerator ashes in landfill or anaerobic bioreactors or heavy metals contaminated in anaerobic digesters. One milliliter (equal to 1 mg) of each metal was added to the 100 ml MSW and the batch reactor test was carried out. The results showed that higher HNO{sub 3} and NaOH were consumed at extreme pH of 1 and 13 compared to those from pH 2 to 11 due to the comparably higher buffer capacity. Pb was found to have the least soluble level, highest metal adsorption (%) and highest partitioning K{sub d} (l g{sup -1}) between pH 3 and 12. In contrast, Ni showed the highest soluble level, lowest metal adsorption (%) and lowest K{sub d} (l g{sup -1}) between pH 4 and 12. Except Ni and Cr, other four metals seemed to show the amphibious properties as comparative higher solubility was found in the acidic and basic conditions.

The measurement of metallic uranium solubility in lithium chloride molten salt

International Nuclear Information System (INIS)

Park, K. K.; Choi, I. K.; Yeon, J. W.; Choi, K. S.; Park, Y. J.

2002-01-01

For the purpose of more precise solubility measurement of metallic uranium in lithium chloride melt, the effect of lithium chloride on uranium determination and and the change of oxidation state of metallic uranium in the media were investigated. Uranium of higher than 10 μg/g could be directly determined by ICP-AES. In the case of the lower concentration, the separation and concentration of uranium by anion exchanger was followed by ICP-AES, thereby extending the measurable concentration to 0.1 μg/g. The effects of lithium oxide, uranium oxides(UO 2 or U 3 O 8 ) and metallic lithium on the solubility of metallic uranium were individually investigated in glassy carbon or stainless steel crucibles under argon gas atmosphere. Since metallic uranium is oxidized to uranium(III) in the absence of metallic lithium, causing an increase in the solubility, metallic lithium as reducing agent should be present in the reaction media to obtain the more precise solubility. The metallic uranium solubilities measured at 660 and 690 .deg. C were both lower than 10 μg/g

Dried gamma-irradiated sewage solids use on calcareous soils: crop yields and heavy metals uptake

International Nuclear Information System (INIS)

McCaslin, B.D.; Sivinski, J.S.

1980-01-01

The fertilizer values of gamma-irradiated digested sewage solids (RDSS) and gamma-irradiated undigested sewage solids (RUSS) have been examined on calcareous soils. Previously published data from Sandia Laboratories have shown that approximately 1 mega-rad of gamma-irradiation effectively destroys pathogenic bacteria, parasites and plant seeds in dried sewage solids. Greenhouse experiments directly comparing gamma-irradiated and non-irradiated undigested and digested dried sewage solids as fertilizers indicate little or no effect of 1 mega-rad gamma radiation treatment on plant yield or plant-nutrient uptake and demonstrated considerable benefit from using sewage solids on calcareous soils. Plant response to undigested sewage solids was considerably greater than to digested sewage solids when applied at levels that were isonitrogenous. The calcareous soils in New Mexico typically range in pH from 7.5 to 9.0, limiting the plant-availability of many elements, especially heavy metals. Soils irrigated with sewage-effluent for 40 years demonstrated beneficial use of supplied plant-nutrients with no apparent increase in plant-uptake of heavy metals. RDSS applied to a calcareous soil low in plant-available iron increased plant growth in the greenhouse considerably more than treatments with equal amounts of nitrogen, phosphorus and iron applied as common fertilizer materials. Plant tissue concentrations of Fe, Zn, Mn and Cu showed that RDSS was a good source of these nutrients. Results also indicated that the total soluble salt concentration of the RDSS was the factor most limiting plant growth. Chromium, Cd, Ni and Pd plant-tissue concentrations were apparently not increased by RDSS treatments. (Auth.)

Analysis and environmental concentrations of the herbicide dichlobenil and its main metabolite 2,6-dichlorobenzamide (BAM)

DEFF Research Database (Denmark)

Björklund, Bengt Erland; Anskjær, Gitte Gotholdt; Hansen, Martin

2011-01-01

in the environment, and primarily bound to solid matrices. Of great concern is its main degradation product 2,6-dichlorobenzamide which is water soluble and therefore transported downward in aquifers, contaminating groundwater resources. It is often found in concentrations exceeding 0.1 μg/L, which is the maximum...... allowed concentration of pesticides in groundwater set by the European Commission. In many countries, the usage of dichlobenil and the problems associated with groundwater contamination by 2,6-dichlorobenzamide have resulted in intensive research and monitoring of these compounds. This review gives...

Pharmaceutical cocrystals:formation mechanisms, solubility behaviour and solid-state properties

OpenAIRE

Alhalaweh, Amjad

2012-01-01

The primary aim of pharmaceutical materials engineering is the successful formulation and process development of pharmaceutical products. The diversity of solid forms available offers attractive opportunities for tailoring material properties. In this context, pharmaceutical cocrystals, multicomponent crystalline materials with definite stoichiometries often stabilised by hydrogen bonding, have recently emerged as interesting alternative solid forms with potential for improving the physical a...

Actinide solution equlibria and solubilities in geologic systems

International Nuclear Information System (INIS)

Allard, B.

1983-04-01

Stability constants and solubility products for actinide (Th, U, Np, Pu and Am) hydroxide and carbonate complexes have been collected, and total solubilities have been calculated under conditions representative of deep granitic groundwaters (pH 7-9.5; high total carbonate concentration according to log (CO 3 )=0.76pH-10.83; redox potentials corresponding to oxic systems, Eh>0.8-0.06pH, and reducing systems, Eh 2 (s), UO 2 (s), NpO 2 (s), PuO 2 (s) and Am 2 (CO 3 ) 3 (s)m, respectively, and the corresponding calculated maximum solubilities are 3 times 10- 10 M(0.07 μg/1) for Th, 0.3-250 times 10- 10 M (0.01-6 μg/1) for U (depending on the carbonate concentration), 1 times 10- 10 M(0.03 μg/1) for Np, 1-3 times 10- 9 M (0.2-0.7 μg/1) for Pu and 0.6-2 times 10- 7 M (15-50 μg/1) for Am. The calculated solubilities for U are in fair agreement with observed uranium concentrations in natural deep groundwaters. Hexavalent uranium carbonate species would dominate in solution except under highly reducing conditions (Eh 5 -10- 6 M (mg/1-level). (author)

Solubility studies of Np(IV)

International Nuclear Information System (INIS)

Zhang Yingjie; Yao Jun; Jiao Haiyang; Ren Lihong; Zhou Duo; Fan Xianhua

2001-01-01

The solubility of Np(IV) in simulated underground water and redistilled water has been measured with the variations of pH(6-12) and storage time (0-100 d) in the presence of reductant (Na 2 S 2 O 4 , metallic Fe). All experiments are performed in a low oxygen concentration glove box containing high purity Ar(99.99%), with an oxygen content of less than 5 x 10 -6 mol/mol. Experimental results show that the variation of pH in solution has little effect on the solubility of Np(IV) in the two kinds of water; the measured solubility of Np(IV) is affected by the composition of solution; with Na 2 S 2 O 4 as a reductant, the solubility of Np(IV) in simulated underground water is (9.23 +- 0.48) x 10 -10 mol/L, and that in redistilled water is (8.31 +- 0.35) x 10 -10 mol/L; with metallic Fe as a reductant, the solubility of Np(IV) in simulated underground water is (1.85 +- 0.56) x 10 -9 mol/L, and that in redistilled water is (1.48 +- 0.66) x 10 -9 mol/L

Solubility of radionuclides in a bentonite environment for provisional safety analyses for SGT-E2

International Nuclear Information System (INIS)

Berner, U.

2014-08-01

Within stage 2 of the sectoral plan for deep geological repositories for radioactive waste in Switzerland provisional safety analyses are carried out. In the case of the repository for spent fuel and vitrified high level waste considered, retention mechanisms include the concentration limits of safety relevant elements in the pore water of the buffer material (bentonite). The present work describes the solubility limits of the safety relevant elements Be, C_i_n_o_r_g, Cl, K, Ca, Co, Ni, Se, Sr, Zr, Nb, Mo, Tc, Pd, Ag, Sn, I, Cs, Sm, Eu, Ho, Pb, Po, Ra, Ac, Th, Pa, U, Np, Pu, Am and Cm in the pore water of bentonite after diffusive solution exchange with the host rock Opalinus Clay. The term solubility limit denotes the maximum amount of an element dissolving in the pore solution of the considered chemical reference system. Chemical equilibrium thermodynamics is the classical tool used for quantifying such considerations. For a given solid phase equilibrium thermodynamics predict the amount of substance dissolving in the solution and describe the speciation of the considered element in solution. The principles of chemical equilibrium will also be the primary work hypothesis in the present work. Solubility calculations were performed with the most recent version of GEMS/PSI (GEMS3.2 v.890) using the PSI/Nagra Chemical Thermodynamic Data Base 12/07, which is an update of the former Nagra/PSI Chemical Thermodynamic Data Base 01/01. The database was complemented with datasets from the ThermoChimie v. 7b for elements that were not considered in the mentioned update (Ag, Co, Sm, Ho, Pa, Be), with data from Iupac (Pb) and with data from the literature (Mo). Differing sources for thermodynamic data are noted. Reference values as well as lower and upper guideline values are evaluated. For many formation constants of solids and solutes uncertainties are known and allow conveying lower and upper guideline values. In many cases it is not clear whether the most stable solid is

The solubility of solid fission products in carbides and nitrides of uranium and plutonium: Pt.2. Solubility rules based on lattice parameter differences

International Nuclear Information System (INIS)

Benedict, U.

1977-01-01

The Relative Lattice Parameter Difference (RLPD) is defined for a solute element with respect to cubic carbides and nitrides of uranium and plutonium as solvents. Rules are given for the relationship between the solubility and the RLPD. NaCl type monocarbides with RLPD's from -10.2% to +7.8% are completely miscible with UC and PuC. NaCl type mononitrides with RLPD's from -7.5% to +8.5% are completely miscible with UN and PuN. The solubility in the sesquicarbides increases with decreasing RPLD and becomes complete in Pu 2 C 3 at RLPD = +4%, and in U 2 C 3 at RLPD approximately +1.5%. Solubilities are predicted on the basis of these rules for the cases where no experimental results are available

Soluble CD30 concentrations in ESRD patients with and without panel reactive HLA antibodies.

Science.gov (United States)

Vaidya, Smita; Partlow, David; Barnes, Titus; Thomas, Phillip; Gugliuzza, Kristin

2006-01-01

In this retrospective study we compared accuracy of panel reactive antibodies (PRA) with serum soluble CD30 (sCD30) contents in predicting acute rejection crisis post-renal transplant. Pre-transplant sera from 115 patients were evaluated for their PRA and sCD30 concentrations. All patients received calcineurin inhibitor-based immunosuppressive therapy. Objective measurements for rejection were biopsy-proven acute rejection (AR) episodes within first six months of the transplant. Post-transplant sera of patients with AR were tested for the presence of donor-specific HLA antibodies (DSA). Overall AR rate was 16% (18/115). Patients positive for PRA and sCD30 tests were at significantly higher risk for AVR compared with those patients negative for both the tests (36% vs. 5%, p=0.01). Among negative PRA patients risk for AR was significantly elevated if they were also tested positive for sCD30 concentrations (21% vs. 5%, p=0.04). Of the 18 patients with AR, 14 were positive for sCD30, and 13 of them (93%) developed DSA post-transplant (p=0.001). These data showed that patients positive for sCD30 contents are at high risk for the development of DSA and AR post-transplant regardless of their pre-transplant PRA.

On nitrogen solubility in water

International Nuclear Information System (INIS)

Kalajda, Yu.A.; Katkov, Yu.D.; Kuznetsov, V.A.; Lastovtsev, A.Yu.; Lastochkin, A.P.; Susoev, V.S.

1980-01-01

Presented are the results of experimental investigations on nitrogen solubility in water under 0-15 MPa pressure, at the temperature of 100-340 deg C and nitrogen concentration of 0-5000 n.ml. N 2 /kg H 2 O. Empiric equations are derived and a diagram of nitrogen solubility in water is developed on the basis of the experimental data, as well as critically evaluated published data. The investigation results can be used in analyzing water-gas regime of a primary heat carrier in stream-generating plants with water-water reactors

Thermodynamic description of Tc(iv) solubility and carbonate complexation in alkaline NaHCO3-Na2CO3-NaCl systems.

Science.gov (United States)

Baumann, A; Yalçıntaş, E; Gaona, X; Polly, R; Dardenne, K; Prüßmann, T; Rothe, J; Altmaier, M; Geckeis, H

2018-03-28

The solubility of 99 Tc(iv) was investigated in dilute to concentrated carbonate solutions (0.01 M ≤ C tot ≤ 1.0 M, with C tot = [HCO 3 - ] + [CO 3 2- ]) under systematic variation of ionic strength (I = 0.3-5.0 M NaHCO 3 -Na 2 CO 3 -NaCl-NaOH) and pH m (-log[H + ] = 8.5-14.5). Strongly reducing conditions (pe + pH m ≈ 2) were set with Sn(ii). Carbonate enhances the solubility of Tc(iv) in alkaline conditions by up to 3.5 log 10 -units compared to carbonate-free systems. Solvent extraction and XANES confirmed that Tc was kept as +IV during the timeframe of the experiments (≤ 650 days). Solid phase characterization performed by XAFS, XRD, SEM-EDS, chemical analysis and TG-DTA confirmed that TcO 2 ·0.6H 2 O(am) controls the solubility of Tc(iv) under the conditions investigated. Slope analysis of the solubility data in combination with solid/aqueous phase characterization and DFT calculations indicate the predominance of the species Tc(OH) 3 CO 3 - at pH m ≤ 11 and C tot ≥ 0.01 M, for which thermodynamic and activity models are derived. Solubility data obtained above pH m ≈ 11 indicates the formation of previously unreported Tc(iv)-carbonate species, possibly Tc(OH) 4 CO 3 2- , although the likely formation of additional complexes prevents deriving a thermodynamic model valid for this pH m -region. This work provides the most comprehensive thermodynamic dataset available for the system Tc 4+ -Na + -Cl - -OH - -HCO 3 - -CO 3 2- -H 2 O(l) valid under a range of conditions relevant for nuclear waste disposal.

Bulk metal concentrations versus total suspended solids in rivers: Time-invariant & catchment-specific relationships.

Science.gov (United States)

Nasrabadi, Touraj; Ruegner, Hermann; Schwientek, Marc; Bennett, Jeremy; Fazel Valipour, Shahin; Grathwohl, Peter

2018-01-01

Suspended particles in rivers can act as carriers of potentially bioavailable metal species and are thus an emerging area of interest in river system monitoring. The delineation of bulk metals concentrations in river water into dissolved and particulate components is also important for risk assessment. Linear relationships between bulk metal concentrations in water (CW,tot) and total suspended solids (TSS) in water can be used to easily evaluate dissolved (CW, intercept) and particle-bound metal fluxes (CSUS, slope) in streams (CW,tot = CW + CSUS TSS). In this study, we apply this principle to catchments in Iran (Haraz) and Germany (Ammer, Goldersbach, and Steinlach) that show differences in geology, geochemistry, land use and hydrological characteristics. For each catchment, particle-bound and dissolved concentrations for a suite of metals in water were calculated based on linear regressions of total suspended solids and total metal concentrations. Results were replicable across sampling campaigns in different years and seasons (between 2013 and 2016) and could be reproduced in a laboratory sedimentation experiment. CSUS values generally showed little variability in different catchments and agree well with soil background values for some metals (e.g. lead and nickel) while other metals (e.g. copper) indicate anthropogenic influences. CW was elevated in the Haraz (Iran) catchment, indicating higher bioavailability and potential human and ecological health concerns (where higher values of CSUS/CW are considered as a risk indicator).

Biopharmaceutical characterisation of ciprofloxacin-metallic ion interactions: comparative study into the effect of aluminium, calcium, zinc and iron on drug solubility and dissolution.

Science.gov (United States)

Stojković, Aleksandra; Tajber, Lidia; Paluch, Krzysztof J; Djurić, Zorica; Parojčić, Jelena; Corrigan, Owen I

2014-03-01

Ciprofloxacin bioavailability may be reduced when ciprofloxacin is co-administered with metallic ion containing preparations. In our previous study, physicochemical interaction between ciprofloxacin and ferrous sulphate was successfully simulated in vitro. In the present work, comparative in vitro ciprofloxacin solubility and dissolution studies were performed in the reactive media containing aluminium hydroxide, calcium carbonate or zinc sulphate. Solid phases collected from the dissolution vessel with aluminium hydroxide, calcium carbonate and zinc sulphate were investigated for their properties. The results obtained indicate that different types of adducts may form and retard ciprofloxacin solubility and dissolution. In the case of aluminium, no phase changes were observed. The solid phase generated in the presence of calcium carbonate was identified as hydrated ciprofloxacin base. Similarly to iron, a new complex consistent with Zn(SO4)2(Cl)2(ciprofloxacin)2 × nH2O stoichiometry was generated in the presence of relatively high concentrations of ciprofloxacin hydrochloride and zinc sulphate, indicating that small volume dissolution experiments can be useful for biorelevant dissolution tests.

Biopharmaceutical characterisation of ciprofloxacin-metallic ion interactions: Comparative study into the effect of aluminium, calcium, zinc and iron on drug solubility and dissolution

Directory of Open Access Journals (Sweden)

Stojković Aleksandra

2014-03-01

Full Text Available Ciprofloxacin bioavailability may be reduced when ciprofloxacin is co-administered with metallic ion containing preparations. In our previous study, physicochemical interaction between ciprofloxacin and ferrous sulphate was successfully simulated in vitro. In the present work, comparative in vitro ciprofloxacin solubility and dissolution studies were performed in the reactive media containing aluminium hydroxide, calcium carbonate or zinc sulphate. Solid phases collected from the dissolution vessel with aluminium hydroxide, calcium carbonate and zinc sulphate were investigated for their properties. The results obtained indicate that different types of adducts may form and retard ciprofloxacin solubility and dissolution. In the case of aluminium, no phase changes were observed. The solid phase generated in the presence of calcium carbonate was identified as hydrated ciprofloxacin base. Similarly to iron, a new complex consistent with Zn(SO42(Cl2(ciprofloxacin2 × nH2O stoichiometry was generated in the presence of relatively high concentrations of ciprofloxacin hydrochloride and zinc sulphate, indicating that small volume dissolution experiments can be useful for biorelevant dissolution tests.

Comparison of three different types of cilostazol-loaded solid dispersion: Physicochemical characterization and pharmacokinetics in rats.

Science.gov (United States)

Mustapha, Omer; Kim, Kyung Soo; Shafique, Shumaila; Kim, Dong Shik; Jin, Sung Giu; Seo, Youn Gee; Youn, Yu Seok; Oh, Kyung Taek; Yong, Chul Soon; Kim, Jong Oh; Choi, Han-Gon

2017-06-01

The aim of this research was to compare three different types of cilostazol-loaded solid dispersion system including solvent-evaporated, solvent-wetted and surface-attached solid dispersion. The effect of polymers and surfactants on the aqueous solubility of cilostazol was investigated, leading to the selection of polyvinylpyrrolidone (PVP) and sodium lauryl sulphate (SLS). Employing a spray-drying technique, numerous surface-attached, solvent-evaporated and solvent-wetted solid dispersions were prepared with various amounts PVP and SLS using water, 90% ethanol and acetone, respectively. Their physicochemical properties, solubility, dissolution and oral bioavailability in rats were assessed compared to the drug powder. Among each solid dispersion system tested, the surface-attached, solvent-evaporated and solvent-wetted solid dispersions composed of cilostazol, PVP and SLS at weight ratios of 3.0 : 0.75 : 1.5, 3.0 : 3.0 : 1.5 and 3.0 : 3.0 : 1.5, respectively, provided the highest drug solubility and dissolution. The solvent-evaporated solid dispersion gave homogeneous and very small spherical particles, in which the drug was changed to an amorphous state. In the solvent-wetted solid dispersion, the amorphous drug was attached to the polymer surface. Conversely, in the surface-attached solid dispersion, the carriers were adhered onto the surface of the unchanged crystalline drug. The solubility, dissolution and oral bioavailability were significantly increased in the order of solvent-evaporated>solvent-wetted>surface-attached>drug powder. Thus, the type of solid dispersion considerably affected the physicochemical properties, aqueous solubility and oral bioavailability. Furthermore, the cilostazol-loaded solvent-evaporated solid dispersion with the highest oral bioavailability would be actively recommended as a practical oral pharmaceutical product. Copyright © 2017 Elsevier B.V. All rights reserved.

Spray Freeze-drying - The Process of Choice for Low Water Soluble Drugs?

International Nuclear Information System (INIS)

Leuenberger, H.

2002-01-01

Most of the novel highly potent drugs, developed on the basis of modern molecular medicine, taking into account cell surface recognition techniques, show poor water solubility. A chemical modification of the drug substance enhancing the solubility often decreases the pharmacological activity. Thus, as an alternative an increase of the solubility can be obtained by the reduction of the size of the drug particles. Unfortunately, it is often difficult to obtain micro or nanosized drug particles by classical or more advanced crystallization using supercritical gases or by milling techniques. In addition, nanosized particles are often not physically stable and need to be stabilized in an appropriate matrix. Thus, it may be of interest to manufacture directly nanosized drug particles stabilized in an inert hydrophilic matrix, i.e. nanostructured and nanocomposite systems. Solid solutions and solid dispersions represent nanostructured and nanocomposite systems. In this context, the use of the vacuum-fluidized-bed technique for the spray-drying of a low water soluble drug cosolubilized with a hydrophilic excipient in a polar organic solvent is discussed. In order to avoid the use of organic solvents, a special spray-freeze-drying technique working at atmospheric pressure is presented. This process is very suitable for temperature and otherwise sensitive drugs such as pharmaproteins

Tetraphenylborate Solubility in High Ionic Strength Salt Solutions

International Nuclear Information System (INIS)

Serkiz, S.M.; Ginn, J.D.; Jurgensen, A.R.

1998-04-01

Solubility of sodium and potassium salts of the tetraphenylborate ion (TPB) in simulated Savannah River Site High Level Waste was investigated. Data generated from this study allow more accurate predictions of TPB solubility at the In-Tank Precipitation (ITP) facility. Because previous research showed large deviations in the observed solubility of TPB salts when compared with model predictions, additional data were generated to better understand the solubility of TPB in more complex systems of high ionic strength and those containing both potassium and sodium. These data allow evaluation of the ability of current models to accurately predict equilibrium TPB concentrations over the range of experimental conditions investigated in this study

Calibration of a turbidity meter for making estimates of total suspended solids concentrations and beam attenuation coefficients in field experiments

Science.gov (United States)

Usry, J. W.; Whitlock, C. H.

1981-01-01

Management of water resources such as a reservoir requires using analytical models which describe such parameters as the suspended sediment field. To select or develop an appropriate model requires making many measurements to describe the distribution of this parameter in the water column. One potential method for making those measurements expeditiously is to measure light transmission or turbidity and relate that parameter to total suspended solids concentrations. An instrument which may be used for this purpose was calibrated by generating curves of transmission measurements plotted against measured values of total suspended solids concentrations and beam attenuation coefficients. Results of these experiments indicate that field measurements made with this instrument using curves generated in this study should correlate with total suspended solids concentrations and beam attenuation coefficients in the water column within 20 percent.

Circulating ghrelin, leptin, and soluble leptin receptor concentrations and cardiometabolic risk factors in a community-based sample.

Science.gov (United States)

Ingelsson, Erik; Larson, Martin G; Yin, Xiaoyan; Wang, Thomas J; Meigs, James B; Lipinska, Izabella; Benjamin, Emelia J; Keaney, John F; Vasan, Ramachandran S

2008-08-01

The conjoint effects and relative importance of ghrelin, leptin, and soluble leptin receptor (sOB-R), adipokines involved in appetite control and energy expenditure in mediating cardiometabolic risk, is unknown. The objective of the study was to study the cross-sectional relations of these adipokines to cardiometabolic risk factors in a community-based sample. We measured circulating ghrelin, leptin, and sOB-R in 362 participants (mean age 45 yr; 54% women) of the Framingham Third Generation Cohort. Body mass index, waist circumference (WC), blood pressure, lipid measures, fasting glucose, smoking, and metabolic syndrome (MetS) were measured. Ghrelin and leptin concentrations were significantly higher in women (P risk.

Solid dispersions, part I: recent evolutions and future opportunities in manufacturing methods for dissolution rate enhancement of poorly water-soluble drugs.

Science.gov (United States)

Bikiaris, Dimitrios N

2011-11-01

In recent years, the number of active pharmaceutical ingredients with high therapeutic impact, but very low water solubility, has increased significantly. Thus, a great challenge for pharmaceutical technology is to create new formulations and efficient drug-delivery systems to overcome these dissolution problems. Drug formulation in solid dispersions (SDs) is one of the most commonly used techniques for the dissolution rate enhancement of poorly water-soluble drugs. Generally, SDs can be defined as a dispersion of active ingredients in molecular, amorphous and/or microcrystalline forms into an inert carrier. This review covers literature which states that the dissolution enhancement of SDs is based on the fact that drugs in the nanoscale range, or in amorphous phase, dissolve faster and to a greater extent than micronized drug particles. This is in accordance to the Noyes-Whitney equation, while the wetting properties of the used polymer may also play an important role. The main factors why SD-based pharmaceutical products on the market are steadily increasing over the last few years are: the recent progress in various methods used for the preparation of SDs, the effect of evolved interactions in physical state of the drug and formulation stability during storage, the characterization of the physical state of the drug and the mechanism of dissolution rate enhancement.

Novel in situ self-assembly nanoparticles for formulating a poorly water-soluble drug in oral solid granules, improving stability, palatability, and bioavailability

Directory of Open Access Journals (Sweden)

Guo S

2016-04-01

Full Text Available Shujie Guo,1 Kevin Pham,2 Diana Li,2 Scott R Penzak,3 Xiaowei Dong2 1State Key Laboratory of Medical Genomics, Shanghai Key Laboratory of Hypertension, Ruijin Hospital, Shanghai Jiao Tong University School of Medicine, Shanghai, People’s Republic of China; 2Department of Pharmaceutical Sciences, 3Department of Pharmacotherapy, University of North Texas Health Science Center, Fort Worth, TX, USA Purpose: The purpose of this study was to develop a novel lipid-based nanotechnology to formulate poorly water-soluble drugs in oral solid granules to improve stability, palatability, and bioavailability. Materials and methods: In one method, we prepared ritonavir (RTV nanoparticles (NPs by a microemulsion-precursor method and then converted the RTV NPs to solid granules by wet granulation to produce RTV NP-containing granules. In the other innovative method, we did not use water in the formulation preparation, and discovered novel in situ self-assembly nanoparticles (ISNPs. We prepared RTV ISNP granules that did not initially contain NPs, but spontaneously produced RTV ISNPs when the granules were introduced to water with gentle agitation. We fully characterized these RTV nanoformulations. We also used rats to test the bioavailability of RTV ISNP granules. Finally, an Astree electronic tongue was used to assess the taste of the RTV ISNP granules. Results: RTV NP-containing granules only had about 1% drug loading of RTV in the solid granules. In contrast, RTV ISNP granules achieved over 16% drug loading and were stable at room temperature over 24 weeks. RTV ISNPs had particle size between 160 nm and 300 nm with narrow size distribution. RTV ISNPs were stable in simulated gastric fluid for 2 hours and in simulated intestinal fluid for another 6 hours. The data from the electronic tongue showed that the RTV ISNP granules were similar in taste to blank ISNP granules, but were much different from RTV solution. RTV ISNP granules increased RTV bioavailability

Solubilities of uranium for TILA-99

International Nuclear Information System (INIS)

Ollila, K.; Ahonen, L.

1998-11-01

This report presents the evaluation of the uranium solubilities in the reference waters of TILA-99. The behaviour of uranium has been discussed separately in the near-field and far-field conditions. The bentonite/groundwater interactions have been considered in the compositions of the fresh and saline near-field reference waters. The far-field groundwaters' compositions include fresh, brackish, saline and very saline, almost brine-type compositions. The pH and redox conditions, as the main parameters affecting the solubilities, are considered. A literature study was made in order to obtain information on the recent dissolution and leaching experiments of UO 2 and spent fuel. The latest literature includes studies on UO 2 solubility under anoxic conditions, in which the methods for simulating the reducing conditions of deep groundwater have been improved. Studies on natural uraninite and its alteration products give a valuable insight into the long-term behaviour of spent fuel. Also the solubility equilibria for some relevant poorly known uranium minerals have been determined. The solubilities of the selected solubility-limiting phases were calculated using the geochemical code, EQ3/6. The NEA database for uranium was the basis for the modelling. The recently extended and updated SR '97 database was used for comparison. The solubility products for uranophane were taken from the latest literature. The recommended values for solubilities were given after a comparison between the calculated solubilities, experimental information and measured concentrations in natural groundwaters. The experiments include several UO 2 dissolution studies in synthetic groundwaters with compositions close to the reference groundwaters. (author)

Solubilities of uranium for TILA-99

Energy Technology Data Exchange (ETDEWEB)

Ollila, K. [VTT Chemical Technology, Espoo (Finland); Ahonen, L. [Geological Survey of Finland, Espoo (Finland)

1998-11-01

This report presents the evaluation of the uranium solubilities in the reference waters of TILA-99. The behaviour of uranium has been discussed separately in the near-field and far-field conditions. The bentonite/groundwater interactions have been considered in the compositions of the fresh and saline near-field reference waters. The far-field groundwaters` compositions include fresh, brackish, saline and very saline, almost brine-type compositions. The pH and redox conditions, as the main parameters affecting the solubilities, are considered. A literature study was made in order to obtain information on the recent dissolution and leaching experiments of UO{sub 2} and spent fuel. The latest literature includes studies on UO{sub 2} solubility under anoxic conditions, in which the methods for simulating the reducing conditions of deep groundwater have been improved. Studies on natural uraninite and its alteration products give a valuable insight into the long-term behaviour of spent fuel. Also the solubility equilibria for some relevant poorly known uranium minerals have been determined. The solubilities of the selected solubility-limiting phases were calculated using the geochemical code, EQ3/6. The NEA database for uranium was the basis for the modelling. The recently extended and updated SR `97 database was used for comparison. The solubility products for uranophane were taken from the latest literature. The recommended values for solubilities were given after a comparison between the calculated solubilities, experimental information and measured concentrations in natural groundwaters. The experiments include several UO{sub 2} dissolution studies in synthetic groundwaters with compositions close to the reference groundwaters. (author) 81 refs.

Achieving concentrated graphene dispersions in water/acetone mixtures by the strategy of tailoring Hansen solubility parameters

International Nuclear Information System (INIS)

Yi Min; Shen Zhigang; Zhang Xiaojing; Ma Shulin