Solubility and precipitation of Fe on reduced TiO{sub 2}(001)

Energy Technology Data Exchange (ETDEWEB)

Busiakiewicz, Adam, E-mail: adambus@uni.lodz.pl

2014-01-01

The solubility of Fe in reduced rutile TiO{sub 2} crystals and the followed precipitation on the (001) surface have been studied using X-ray photoelectron spectroscopy (XPS) and scanning tunneling microscopy (STM) in ultra-high vacuum. The first step includes dissolving Fe in reduced TiO{sub 2} at 1073 K by the means of thermal diffusion and as a result the saturated solid solution is formed. Then, it undergoes fast cooling which leads to obtaining a supersaturated solid solution. When this supersaturated crystal is annealed at low temperatures of about 500 K, Fe starts to precipitate on the (001) surface forming spherical Fe-containing nanoparticles. The fast migration of Fe cations to the surface and their precipitation at relatively low temperatures are caused by high diffusion anisotropy and the reduction of the TiO{sub 2}. At about 900 K, the size of nanoparticles increases and they are transformed into nanocrystals with clearly visible facets. Simultaneously, the number of the nanocrystals substantially decreases. The partial oxidation of Fe is also observed around 900 K, which is related to strong metal support interaction between Fe and reduced TiO{sub 2}(001). The XPS and STM results suggest that the nanocrystals are mostly composed of mixed Fe/Ti oxides like FeTiO{sub 3} of ilmenite structure. Above 973 K, the nanocrystals disappear which is explained by the restored solubility of Fe cations in the reduced TiO{sub 2}. The process of the nanoparticle precipitation at lower temperatures is repeatable and the precipitation and disappearance of Fe-containing nanocrystals on TiO{sub 2}(001) are also a fully reversible phenomenon easily controlled by annealing temperature. - Highlights: • The supersaturated solid solution of Fe in TiO{sub 2}(001) is obtained at 1073 K. • Fe precipitates forming nanoparticles above 500 K and nanocrystals above 900 K. • Nanocrystals are ascribed to formation of FeTiO{sub 3} compound.

Effects of iron(III)chelates on the solubility of heavy metals in calcareous soils

Energy Technology Data Exchange (ETDEWEB)

Ylivainio, Kari, E-mail: kari.ylivainio@mtt.f [Department of Applied Chemistry and Microbiology, FIN-00014 University of Helsinki (Finland)

2010-10-15

In this study I evaluated the effects of complexing agents on the solubility of heavy metals in an incubation experiment up to 56 days when complexing agents were applied as Fe-chelates (Fe-EDDS(S,S), Fe-EDDS(mix), Fe-EDTA and Fe-EDDHA) on calcareous soils at a level sufficient to correct Fe chlorosis (0.1 mmol kg{sup -1}). Of these ligands, EDDHA was the most efficient in keeping Fe in water-soluble form, and EDDS increased the solubility of Cu and Zn most, and only EDTA increased the solubility of Cd and Pb. EDTA increased the solubility of Ni steadily during the incubation period, equalling about 5-8% of the added EDTA concentration. [S,S]-EDDS was biodegraded within 56 days, whereas EDDS(mix) was less biodegradable. Ni-chelates were the most recalcitrant against biodegradation. The study shows that even a moderate input of chelates to soil increases the solubility of toxic heavy metals and their risk of leaching. - When correcting Fe chlorosis Fe-EDDS causes lower environmental concern than Fe-EDTA.

Effects of iron(III)chelates on the solubility of heavy metals in calcareous soils

International Nuclear Information System (INIS)

Ylivainio, Kari

2010-01-01

In this study I evaluated the effects of complexing agents on the solubility of heavy metals in an incubation experiment up to 56 days when complexing agents were applied as Fe-chelates (Fe-EDDS(S,S), Fe-EDDS(mix), Fe-EDTA and Fe-EDDHA) on calcareous soils at a level sufficient to correct Fe chlorosis (0.1 mmol kg -1 ). Of these ligands, EDDHA was the most efficient in keeping Fe in water-soluble form, and EDDS increased the solubility of Cu and Zn most, and only EDTA increased the solubility of Cd and Pb. EDTA increased the solubility of Ni steadily during the incubation period, equalling about 5-8% of the added EDTA concentration. [S,S]-EDDS was biodegraded within 56 days, whereas EDDS(mix) was less biodegradable. Ni-chelates were the most recalcitrant against biodegradation. The study shows that even a moderate input of chelates to soil increases the solubility of toxic heavy metals and their risk of leaching. - When correcting Fe chlorosis Fe-EDDS causes lower environmental concern than Fe-EDTA.

Solubility of nitrogen in iron alloys with vanadium and niobium

International Nuclear Information System (INIS)

Pomarin, Yu.M.; Grigorenko, G.M.; Lakomskij, V.I.

1975-01-01

The solubility of nitrogen in the concentration range under study in Fe-N-V and Fe-N-Nb systems is in compliance with Syverts' law. An equation has been set up so as to estimate the nitrogen solubility in the iron alloys containing up to 10 per cent of vanadium and niobium in the wide temperature range

A study of the Fe(III)/Fe(II)-triethanolamine complex redox couple for redox flow battery application

International Nuclear Information System (INIS)

Wen, Y.H.; Zhang, H.M.; Qian, P.; Zhou, H.T.; Zhao, P.; Yi, B.L.; Yang, Y.S.

2006-01-01

The electrochemical behavior of the Fe(III)/Fe(II)-triethanolamine(TEA) complex redox couple in alkaline medium and influence of the concentration of TEA were investigated. A change of the concentration of TEA mainly produces the following two results. (1) With an increase of the concentration of TEA, the solubility of the Fe(III)-TEA can be increased to 0.6 M, and the solubility of the Fe(II)-TEA is up to 0.4 M. (2) In high concentration of TEA with the ratio of TEA to NaOH ranging from 1 to 6, side reaction peaks on the cathodic main reaction of the Fe(III)-TEA complex at low scan rate can be minimized. The electrode process of Fe(III)-TEA/Fe(II)-TEA is electrochemically reversible with higher reaction rate constant than the uncomplexed species. Constant current charge-discharge shows that applying anodic active materials of relatively high concentrations facilitates the improvement of cell performance. The open-circuit voltage of the Fe-TEA/Br 2 cell with the Fe(III)-TEA of 0.4 M, after full charging, is nearly 2.0 V and is about 32% higher than that of the all-vanadium batteries, together with the energy efficiency of approximately 70%. The preliminary exploration shows that the Fe(III)-TEA/Fe(II)-TEA couple is electrochemically promising as negative redox couple for redox flow battery (RFB) application

Boron solubility in Fe-Cr-B cast irons

International Nuclear Information System (INIS)

Guo Changqing; Kelly, P.M.

2003-01-01

Boron solubility in the as-cast and solution treated martensite of Fe-Cr-B cast irons, containing approximately 1.35 wt.% of boron, 12 wt.% of chromium, as well as other alloying elements, has been investigated using conventional microanalysis. The significant microstructural variations after tempering at 750 deg. C for 0.5-4 h, compared with the original as-cast and solution treated microstructures, indicated that the matrix consisted of boron and carbon supersaturated solid solutions. The boron solubility detected by electron microprobe was between 0.185-0.515 wt.% for the as-cast martensite and 0.015-0.0589 wt.% for the solution treated martensite, much higher than the accepted value of 0.005 wt.% in pure iron. These remarkable increases are thought to be associated with some metallic alloying element addition, such as chromium, vanadium and molybdenum, which have atomic diameters larger than iron, and expand the iron lattice to sufficiently allow boron atoms to occupy the interstitial sites in iron lattice

Effects of iron(III)chelates on the solubility of heavy metals in calcareous soils.

Science.gov (United States)

Ylivainio, Kari

2010-10-01

In this study I evaluated the effects of complexing agents on the solubility of heavy metals in an incubation experiment up to 56 days when complexing agents were applied as Fe-chelates (Fe-EDDS(S,S), Fe-EDDS(mix), Fe-EDTA and Fe-EDDHA) on calcareous soils at a level sufficient to correct Fe chlorosis (0.1 mmol kg(-1)). Of these ligands, EDDHA was the most efficient in keeping Fe in water-soluble form, and EDDS increased the solubility of Cu and Zn most, and only EDTA increased the solubility of Cd and Pb. EDTA increased the solubility of Ni steadily during the incubation period, equalling about 5-8% of the added EDTA concentration. [S,S]-EDDS was biodegraded within 56 days, whereas EDDS(mix) was less biodegradable. Ni-chelates were the most recalcitrant against biodegradation. The study shows that even a moderate input of chelates to soil increases the solubility of toxic heavy metals and their risk of leaching. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

Determination of Fe²⁺ and Fe³⁺ species by FIA-CRC-ICP-MS in Antarctic ice samples

DEFF Research Database (Denmark)

Spolaor, A; Vallelonga, Paul Travis; Gabrieli, J

2012-01-01

contexts depends strongly on its oxidation state. Solubility in water and the capacity to form complexes are just two important characteristics that are species dependent. Distinguishing between the two iron species, Fe(II) and Fe(III), is necessary to evaluate bioavailability, as Fe(II) is more soluble...... detection limit is 0.01 ng g-1. A chelating resin, Ni-NTA Superflow, was used to separate the Fe species: At pH 2 the resin is capable of retaining Fe3+ with no retention of Fe2+. After the initial separation, we oxidized the Fe2+ using H2O2, and determined the Fe2+ concentration as the difference between...

The solubility of rhodochrosite (MnCO3) and siderite (FeCO3) in anaerobic aquatic environments

DEFF Research Database (Denmark)

Jensen, Dorthe Lærke; Boddum, J.K.; Tjell, Jens Christian

2002-01-01

Natural groundwaters are often reported to be highly supersaturated with the carbonate minerals siderite (FeCO3) and rhodochrosite (MnCO3). The kinetics of precipitation and dissolution were determined in the light of new determinations of the solubility products of siderite and rhodochrosite...... steady state for rhodochrosite was reached after 140 days. Suspensions of siderite and rhodochrosite crystals reached steady state after 10 and 80 days, respectively. The solubility product of siderite (log KS0(FeCO3)) was 11.03 0.10 for dried crystals and 10.43 0.15 for wet crystals. For rhodochrosite...... the solubility product (log KS0(MnCO3)) was 11.39 0.14 for dried crystals and 12.51 0.07 for wet crystals. The solubility product determined from supersaturated solutions was log KS0(MnCO3)=11.65 0.14. The observed slow precipitation kinetics of siderite and rhodochrosite might explain the apparent...

Dissolution behaviour of ferric pyrophosphate and its mixtures with soluble pyrophosphates: Potential strategy for increasing iron bioavailability.

Science.gov (United States)

Tian, Tian; Blanco, Elena; Smoukov, Stoyan K; Velev, Orlin D; Velikov, Krassimir P

2016-10-01

Ferric pyrophosphate (FePP) is a widely used iron source in food fortification and in nutritional supplements, due to its white colour, that is very uncommon for insoluble Fe salts. Although its dissolution is an important determinant of Fe adsorption in human body, the solubility characteristics of FePP are complex and not well understood. This report is a study on the solubility of FePP as a function of pH and excess of pyrophosphate ions. FePP powder is sparingly soluble in the pH range of 3-6 but slightly soluble at pH8. In the presence of pyrophosphate ions the solubility of FePP strongly increases at pH 5-8.5 due to formation a soluble complex between Fe(III) and pyrophosphate ions, which leads to an 8-10-fold increase in the total ionic iron concentration. This finding is beneficial for enhancing iron bioavailability, which important for the design of fortified food, beverages, and nutraceutical products. Copyright © 2016 Elsevier Ltd. All rights reserved.

Concentrations and solubility of selected trace metals in leaf and bagged black teas commercialized in Poland

Directory of Open Access Journals (Sweden)

L. Polechońska

2015-09-01

Full Text Available The objective of this study was to determine the concentrations of heavy metals in bagged and leaf black teas of the same brand and evaluate the percentage transfer of metals to tea infusion to assess the consumer exposure. Ten leaf black teas and 10 bagged black teas of the same brand available in Poland were analyzed for Zn, Mn, Cd, Pb, Ni, Co, Cr, Al, and Fe concentrations both in dry material and their infusion. The bagged teas contained higher amounts of Pb, Mn, Fe, Ni, Al, and Cr compared with leaf teas of the same brand, whereas the infusions of bagged tea contained higher levels of Mn, Ni, Al, and Cr compared with leaf tea infusions. Generally, the most abundant trace metals in both types of tea were Al and Mn. There was a wide variation in percentage transfer of elements from the dry tea materials to the infusions. The solubility of Ni and Mn was the highest, whereas Fe was insoluble and only a small portion of this metal content may leach into infusion. With respect to the acceptable daily intake of metals, the infusions of both bagged and leaf teas analyzed were found to be safe for human consumption.

Synthesis and characterization of magnetic Fe/CNTs composites with controllable Fe nanoparticle concentration

International Nuclear Information System (INIS)

Zhao Fan; Duan Hongyan; Wang Weigao; Wang Jun

2012-01-01

Fe/CNTs composites, with different concentrations of Fe nanoparticles (NPs) on carbon nanotube (CNT) surfaces, were successfully fabricated via a facile solvothermal method. The lengths of CNTs are up to 10 μm and the mean diameter of the Fe nanoparticles is about 25 nm. The structures, composition and magnetic properties of the Fe/CNTs were characterized by XRD, FTIR, FE-SEM, TEM and PPMS. We found that the concentrations of Fe nanoparticles depositing on the CNTs could be controlled by adjusting the initial mass ratio of ferrocene to CNTs. The Fe/CNTs composites display good ferromagnetic properties at room temperature, with a saturation magnetization of 125 emu/g-Fe and a coercivity of 276 Oe. The Curie temperature of the sample is about 1038 K, slightly lower than that (1043 K) of the bulk iron.

Solubility studies of Np(IV)

International Nuclear Information System (INIS)

Zhang Yingjie; Yao Jun; Jiao Haiyang; Ren Lihong; Zhou Duo; Fan Xianhua

2001-01-01

The solubility of Np(IV) in simulated underground water and redistilled water has been measured with the variations of pH(6-12) and storage time (0-100 d) in the presence of reductant (Na 2 S 2 O 4 , metallic Fe). All experiments are performed in a low oxygen concentration glove box containing high purity Ar(99.99%), with an oxygen content of less than 5 x 10 -6 mol/mol. Experimental results show that the variation of pH in solution has little effect on the solubility of Np(IV) in the two kinds of water; the measured solubility of Np(IV) is affected by the composition of solution; with Na 2 S 2 O 4 as a reductant, the solubility of Np(IV) in simulated underground water is (9.23 +- 0.48) x 10 -10 mol/L, and that in redistilled water is (8.31 +- 0.35) x 10 -10 mol/L; with metallic Fe as a reductant, the solubility of Np(IV) in simulated underground water is (1.85 +- 0.56) x 10 -9 mol/L, and that in redistilled water is (1.48 +- 0.66) x 10 -9 mol/L

Cadmium solubility in paddy soils: Effects of soil oxidation, metal sulfides and competitive ions

Energy Technology Data Exchange (ETDEWEB)

Livera, Jennifer de, E-mail: Jennifer.deLivera@adelaide.edu.au [Soil Science, School of Agriculture Food and Wine, Waite Research Institute, University of Adelaide, Adelaide, SA (Australia); McLaughlin, Mike J. [Soil Science, School of Agriculture Food and Wine, Waite Research Institute, University of Adelaide, Adelaide, SA (Australia); CSIRO Land and Water, Environmental Biogeochemistry Program, Sustainable Agriculture Flagship, Adelaide, SA (Australia); Hettiarachchi, Ganga M. [CSIRO Land and Water, Environmental Biogeochemistry Program, Sustainable Agriculture Flagship, Adelaide, SA (Australia); Department of Agronomy, Kansas state University, Manhattan, KS (United States); Kirby, Jason K. [CSIRO Land and Water, Environmental Biogeochemistry Program, Sustainable Agriculture Flagship, Adelaide, SA (Australia); CSIRO Land and Water, Environmental Biogeochemistry Program, Water for a Healthy Country Flagship, Adelaide, SA (Australia); Beak, Douglas G. [CSIRO Land and Water, Environmental Biogeochemistry Program, Sustainable Agriculture Flagship, Adelaide, SA (Australia)

2011-03-15

Cadmium (Cd) is a non-essential element for human nutrition and is an agricultural soil contaminant. Cadmium solubility in paddy soils affects Cd accumulation in the grain of rice. This is a human health risk, exacerbated by the fact that rice grains are deficient in iron (Fe) and zinc (Zn) for human nutrition. To find ways of limiting this potential risk, we investigated factors influencing Cd solubility relative to Fe and Zn during pre-harvest drainage of paddy soils, in which soil oxidation is accompanied by the grain-filling stage of rice growth. This was simulated in temperature-controlled 'reaction cell' experiments by first excluding oxygen to incubate soil suspensions anaerobically, then inducing aerobic conditions. In treatments without sulfur addition, the ratios of Cd:Fe and Cd:Zn in solution increased during the aerobic phase while Cd concentrations were unaffected and the Fe and Zn concentrations decreased. However, in treatments with added sulfur (as sulfate), up to 34 % of sulfur (S) was precipitated as sulfide minerals during the anaerobic phase and the Cd:Fe and Cd:Zn ratios in solution during the aerobic phase were lower than for treatments without S addition. When S was added, Cd solubility decreased whereas Fe and Zn were unaffected. When soil was spiked with Zn the Cd:Zn ratio was lower in solution during the aerobic phase, due to higher Zn concentrations. Decreased Cd:Fe and Cd:Zn ratios during the grain filling stage could potentially limit Cd enrichment in paddy rice grain due to competitive ion effects for root uptake. - Research Highlights: {yields} Cd:Fe and Cd:Zn ratios increase in paddy soil solution during oxidation. {yields} Cd:Fe and Cd:Zn ratios increase because Fe and Zn concentrations decrease. {yields} Cd concentrations do not change during oxidation. {yields} Cd:Fe and Cd:Zn ratios in solution decrease when Zn is added to soil. {yields} Metal sulfide precipitation lowers Cd:Fe and Cd:Zn ratios in soil solution.

Leaching of copper concentrates using NaCl and soluble copper contributed by the own concentrate

International Nuclear Information System (INIS)

Herrero, O.; Bernal, N.; Quiroz, R.; Fuentes, G.; Vinals, J.

2005-01-01

Leaching of copper concentrates using cupric chloro complexes, generated in situ by the reaction between Cu(II), aported by the soluble copper content of the concentrate, and sodium chloride in acid media was studied. The concentrate samples were obtained from mineral processing plants from Antofagasta, Chile. Chemical and mineralogical characterization from original concentrates was made. Typical variable such as a chloride concentration, soluble copper concentration, leaching time, solid percentage and temperature were studied. DRX and EDS analyzed some of the residues. the experimental results indicated that it is possible to obtain solutions having high copper content (15 to 35 g/L) and 2 to 5 g/L free acid in order to submit this solution directly to a solvent extraction stage. The leaching tests use common reactive and low cost such as sodium chloride and sulfuric acid. (Author) 16 refs

Effect of carbon and silicon on nitrogen solubility in liquid chromium and iron-chromium alloys

International Nuclear Information System (INIS)

Khyakkinen, V.I.; Bezobrazov, S.V.

1986-01-01

The study is aimed at specifying the role of carbon and silicon in high-chromium melts nitridation processes. It is shown that in high-chromium melts of the Cr-Fe-C system the nitrogen solubility is reduced with the growth of carbon content and in the chromium concentration range of 70-100% at 1873 K and P N 2 =0.1 MPa it is described by the lg[%N] Cr-Fe-C =lg[%N] cr-fe -0.098[%C] equation. While decreasing the temperature the nitrogen solubility in alloys is increased. Silicon essentially decreases the nitrogen solubility in liquid chromium. For the 0-10% silicon concentration range the relation between the equilibrium content of nitrogen and silicon at 1873 K and P N 2 =0.1 MPa is described by the straight line equation [%N] Cr-Si =6.1-0.338 [%Si

Inter-species comparative analysis of components of soluble sugar concentration in fleshy fruits

Directory of Open Access Journals (Sweden)

Zhanwu eDai

2016-05-01

Full Text Available The soluble sugar concentration of fleshy fruit is a key determinant of fleshy fruit quality. It affects directly the sweetness of fresh fruits and indirectly the properties of processed products (e.g. alcohol content in wine. Despite considerable divergence among species, soluble sugar accumulation in a fruit results from the complex interplay of three main processes, namely sugar import, sugar metabolism, and water dilution. Therefore, inter-species comparison would help to identify common and/or species-specific modes of regulation in sugar accumulation. For this purpose, a process-based mathematical framework was used to compare soluble sugar accumulation in three fruits: grape, tomato and peach. Representative datasets covering the time course of sugar accumulation during fruit development were collected. They encompassed 104 combinations of species (3, genotypes (32, and growing conditions (19 years and 16 nutrient and environmental treatments. At maturity, grape showed the highest soluble sugar concentrations (16.5-26.3 g /100 g FW, followed by peach (2.2 to 20 g /100 g FW and tomato (1.4 to 5 g /100 g FW. Main processes determining soluble sugar concentration were decomposed into sugar importation, metabolism and water dilution with the process-based analysis. Different regulation modes of soluble sugar concentration were then identified, showing either import-based, dilution-based, or import and dilution dual-based. Firstly, the higher soluble sugar concentration in grape than in tomato is a result of higher sugar importation. Secondly, the higher soluble sugar concentration in grape than in peach is due to a lower water dilution. The third mode of regulation is more complicated than the first two, with differences both in sugar importation and water dilution (grape vs cherry tomato; cherry tomato vs peach; peach vs tomato. On the other hand, carbon utilization for synthesis of non-soluble sugar compounds (namely metabolism was

Fe++/Fe+++ concentration relationship and mechanical properties of phosphate glasses useful for wastes immobilization

International Nuclear Information System (INIS)

Garcia, D.A.; Prado, Miguel O.

2007-01-01

Under different melting conditions, glasses with different Fe(II)/Fe(III) concentration relationship were prepared within each type of glass 43Fe 2 O 3 -57P 2 O 5 and 33,33Fe 2 O 3 - 66,67P 2 O 5 . Using Moessbauer spectroscopy Fe(II)/Fe(III) concentration values were determined. Vickers and Knoop indentations were used for determining their hardness, toughness, Young modulus and brittleness. The same measurements were carried on some silicate and aluminosilicate glasses. Also Weibull statistics was done to determine the characteristics (Weibull modulus and and fracture probability) of glass fracture. We found that silicate glasses (SG) are harder than phosphate glasses (PG). Toughness values for PG, are in the same range than for SG, although for the same density exhibit larger values or smaller brittleness than silicate glasses. For one of the glasses it was found that the mechanical load P 0 needed for a fracture probability of 63% increases with the Fe(II) content. (author)

Acetone sensors based on microsheet-assembled hierarchical Fe2O3 with different Fe3+ concentrations

Science.gov (United States)

Wang, Han; Yan, Lei; Li, Shuo; Li, Yu; Liu, Li; Du, Liting; Duan, Haojie; Cheng, Yali

2018-02-01

Several different morphologies of microsheet-assembled Fe2O3 have been fabricated by hydrothermal method using diverse concentrations of Fe3+ precursor solutions (0.025, 0.020, 0.015, 0.010 mol/L Fe3+). The as-synthesized materials have been characterized by scanning electron microscope (SEM), X-ray powder diffraction (XRD), and energy-dispersive X-ray spectrometry (EDS). The SEM images reflect that the morphologies of as-synthesized materials are affected by the concentrations of Fe3+ in precursor solutions. The less concentration of Fe3+, the more porous of Fe2O3 microflowers, and thinner of slices distributed on the surface. Furthermore, gas sensors based on these Fe2O3 microflowers manufactured and tested to various common gases. The optimum response value to 100 ppm acetone is 52 at the working temperature of 220 °C. Meanwhile, the Fe2O3 microflower sensors possess ultrafast response-recovery speed, which are 8 and 19 s, respectively. The possible sensing mechanism was mainly attributed to the high surface area, three-dimensional porous structure.

Mild Fe-deficiency improves biomass production and quality of hydroponic-cultivated spinach plants (Spinacia oleracea L.).

Science.gov (United States)

Jin, Chong-Wei; Liu, Yue; Mao, Qian-Qian; Wang, Qian; Du, Shao-Ting

2013-06-15

It is of great practical importance to improve yield and quality of vegetables in soilless cultures. This study investigated the effects of iron-nutrition management on yield and quality of hydroponic-cultivated spinach (Spinacia oleracea L.). The results showed that mild Fe-deficient treatment (1 μM FeEDTA) yielded a greater biomass of edible parts than Fe-omitted treatment (0 μM FeEDTA) or Fe-sufficient treatments (10 and 50 μM FeEDTA). Conversely, mild Fe-deficient treatment had the lowest nitrate concentration in the edible parts out of all the Fe treatments. Interestingly, all the concentrations of soluble sugar, soluble protein and ascorbate in mild Fe-deficient treatments were higher than Fe-sufficient treatments. In addition, both phenolic concentration and DPPH scavenging activity in mild Fe-deficient treatments were comparable with those in Fe-sufficient treatments, but were higher than those in Fe-omitted treatments. Therefore, we concluded that using a mild Fe-deficient nutrition solution to cultivate spinach not only would increase yield, but also would improve quality. Copyright © 2012 Elsevier Ltd. All rights reserved.

The role of carbon solubility in Fe-C nano-clusters on the growth of small single-walled carbon nanotubes

Science.gov (United States)

Curtarolo, Stefano; Awasthy, Neha; Setyawan, Wahyu; Mora, Elena; Tokune, Toshio; Bolton, Kim; Harutyunyan, Avetik

2008-03-01

Various diameters of alumina-supported Fe catalysts are used to grow single-walled carbon nanotubes (SWCNTs) with chemical vapor decomposition. We find that the reduction of the catalyst size requires an increase of the minimum temperature necessary for the growth. We address this phenomenon in terms of solubility of C in Fe nanoclusters and, by using first principles calculations, we devise a simple model to predict the behavior of the phases competing for stability in Fe-C nanoclusters at low temperature. We show that, as a function particles size, there are three scenarios compatible with steady state-, limited- and no-growth of SWCNTs, corresponding to unaffected, reduced and no solubility of C in the particles. The result raises previously unknown concerns about the growth feasibility of small and very-long SWCNTs within the current Fe CVD technology, and suggests new strategies in the search of better catalysts. Research supported by Honda R.I. and NSF.

Solubility of simulated PWR primary circuit corrosion products

International Nuclear Information System (INIS)

Kunig, R.H.; Sandler, Y.L.

1986-08-01

The solubility behavior of non-stoichiometric nickel ferrites, nickel-cobalt ferrites, and magnetite, as model substances for the corrosion products (''crud'') formed in nuclear pressurized water reactors, was studied in a flow system in aqueous solutions of lithium hydroxide, boric acid, and hydrogen with pH, temperature, and hydrogen concentrations as parameters. Below the temperature region of 300 to 330 0 C, at hydrogen concentrations of 25 to 40 cm 3 /kg H 2 O as used during reactor operation, the solubility of nickel-cobalt ferrite is the same as that of Ni and Co/sub x/Fe/sub 3-x/O 4 (x 3 /kg of hydrogen, the equilibrium iron and nickel solubilities increase congruently down to about 100 0 C, in a manner consistent with the solubility of Fe 3 O 4 , but sharply decline at lower temperatures, apparently due to formation of a borated layer. A cooldown experiment on a time scale of a typical Westinghouse reactor shutdown, as well as static experiments carried out on various ferrite samples at 60 0 C show that after addition of oxygen or peroxide evolution of nickel (and possibly cobalt) above the equilibrium solubility in hydrogen depends on the presence of dissociation products prior to oxidation. Thermodynamic calculations of various reduction and oxidative decomposition reactions for stoichiometric and non-stoichiometric nickel ferrite and cobalt ferrite are presented. Their significance to evolutions of nickel and cobalt on reactor shutdown is discussed. 30 refs., 38 figs., 34 tabs

Solubility Measurements and Modeling of Zinc, Lead and Iron Sulfides at High Temperatures and High Pressures

DEFF Research Database (Denmark)

Carolina Figueroa Murcia, Diana; Fosbøl, Philip Loldrup; Thomsen, Kaj

Solubility measurements of sulfides in aqueous solutions are necessary to understand the behaviour of these scaling minerals in geothermal and oil reservoirs. The low solubility levels of Zinc Sulfide (ZnS), Lead Sulfide (PbS) and Iron Sulfide (FeS) make the solubility measurements a challenging...... oxygen atmosphere to avoid the risk of oxidation of sulfide minerals. The solution is kept in an equilibrium cell at constant temperature and pressure with continuous stirring. The concentration of Zn2+, Pb2+, Fe2+ and S2- are measured using Inductively Coupled Plasma Optical Emission spectrometry (ICP...

Trace-element concentrations and water-soluble ions in size-segregated dust-borne and soil samples in Sistan, southeast Iran

Science.gov (United States)

Behrooz, Reza Dahmardeh; Esmaili-Sari, Abbas; Bahramifar, Nader; Kaskaoutis, D. G.; Saeb, Keivan; Rajaei, Fatemeh

2017-04-01

This study analyzes the chemical composition (water-soluble ions and trace elements) of the total suspended particles (TSP) and particulate matter less than 10 and 2.5 μm (PM10 and PM2.5) in the Sistan basin, southeast Iran during the dusty and windy period June - October 2014. Extreme TSP, PM10 and PM2.5 concentrations, means of 1624.8, 433.4 and 320.8 μgm-3, respectively, were recorded in the Zabol sampling site, while the examined water-soluble ions and trace metals constitute small fractions (∼4.1%-17.7%) of the particulate masses. Intense winds on the dust-storm days result in weathering of soil crust and deflation of evaporate minerals from the dried Hamoun lake beds in the Sistan basin. The soil samples are rich in Ca2+, SO42-, Na+ and Cl- revealing the existence of non-sea salts, as well as in Al, Fe and Mg, while the similarity in the chemical composition between soil and airborne samples indicates that the dust events over Sistan are local in origin. In contrast, low concentrations of secondary ions (i.e., nitrate) and heavy metals (i.e., Pb, Cr, Ni, Cu) indicate less anthropogenic and industrial emissions. Enrichment Factor analysis for TSP, PM10 and PM2.5 reveals that the anthropogenic sources contribute a substantial amount in the heavy metals rather than soil crust, while Al, Fe, Sn, Mg are mostly of crustal origin. The results provide essential knowledge in atmospheric chemistry over Sistan and in establishing mitigation strategies for air pollution control.

Microstructure and thermal stability of Fe, Ti and Ag implanted Yttria-stabilized zirconia

NARCIS (Netherlands)

van Hassel, B.A.; van Hassel, B.A.; Burggraaf, Anthonie; Burggraaf, A.J.

1991-01-01

Yttria-stabilized zirconia (YSZ) was implanted with 15 keV Fe or Ti ions up to a dose of 8×1016 at cm−2. The resulting “dopant” concentrations exceeded the concentrations corresponding to the equilibrium solid solubility of Fe2O3 or TiO2 in YSZ. During oxidation in air at 400° C, the Fe and Ti

Nano-sized Fe2O3/Fe3O4 facilitate anaerobic transformation of hexavalent chromium in soil-water systems.

Science.gov (United States)

Zhang, Yaxian; Li, Hua; Gong, Libo; Dong, Guowen; Shen, Liang; Wang, Yuanpeng; Li, Qingbiao

2017-07-01

The purpose of this study is to investigate the effects of nano-sized or submicro Fe 2 O 3 /Fe 3 O 4 on the bioreduction of hexavalent chromium (Cr(VI)) and to evaluate the effects of nano-sized Fe 2 O 3 /Fe 3 O 4 on the microbial communities from the anaerobic flooding soil. The results indicated that the net decreases upon Cr(VI) concentration from biotic soil samples amended with nano-sized Fe 2 O 3 (317.1±2.1mg/L) and Fe 3 O 4 (324.0±22.2mg/L) within 21days, which were approximately 2-fold of Cr(VI) concentration released from blank control assays (117.1±5.6mg/L). Furthermore, the results of denaturing gradient gel electrophoresis (DGGE) and high-throughput sequencing indicated a greater variety of microbes within the microbial community in amendments with nano-sized Fe 2 O 3 /Fe 3 O 4 than the control assays. Especially, Proteobacteria occupied a predominant status on the phylum level within the indigenous microbial communities from chromium-contaminated soils. Besides, some partial decrease of soluble Cr(VI) in abiotic nano-sized Fe 2 O 3 /Fe 3 O 4 amendments was responsible for the adsorption of nano-sized Fe 2 O 3 /Fe 3 O 4 to soluble Cr(VI). Hence, the presence of nano-sized Fe 2 O 3 /Fe 3 O 4 could largely facilitate the mobilization and biotransformation of Cr(VI) from flooding soils by adsorption and bio-mediated processes. Copyright © 2017. Published by Elsevier B.V.

Solubility of polyvalent cations in fogwater at an urban site in Strasbourg (France)

Science.gov (United States)

Millet, M.; Wortham, H.; Mirabel, Ph.

The concentrations in the soluble and total (soluble + insoluble) fractions of Mg, Ca, Fe, Mn, Zn, Al, Cd and Pb have been analysed by "inductively coupled plasma (ICP)" in 14 fog events collected in 1992 at an urban site in France (Strasbourg). For each fog event, two droplet size categories (2-6 μm and 5-8 μm) have been collected separately. For the analysis of the polyvalent cations in the soluble and total fractions, an analytical procedure using ICP and filtration on cellulose/PVC filters has been developed. The study of the solubility of some polyvalent cations has shown that two of the most important factors controlling the partitioning between the soluble and insoluble fraction are the nature of the particles and the pH of the fogwater. The influence of pH depended on the element. The solubility of Pb, Cd, Al, Fe, Mg, and Ca were pH dependent whereas, Zn and Mn solubility varied but no relationship with pH existed, ranging between 25 and 100% and 10 and 100%, respectively. On the other hand, Mg, Pb and Ca were predominantly present in the soluble phase, whereas Al was prevalent in the insoluble fraction. In the case of Cd and Fe., the presence in the soluble or insoluble phase depended largely on the fogwater pH.

Solubility of chromium (III) oxide and metal chromates: development of MULTEQ models

International Nuclear Information System (INIS)

Dickinson, Shirley; Henshaw, Jim; Bachet Martin; Hussey, Dennis; Marks, Chuck; Tremaine, Peter; Eaker, Richard

2012-09-01

High-temperature solubility predictions for metal oxide systems are important for the understanding of corrosion processes, corrosion product behaviour and activity transport in PWR coolant systems. In the current work, literature data on chromium oxide and iron chromium solubility measurement have been used to derive equilibrium constant expressions for dissolution and hydrolysis reactions which have been incorporated in the latest revision of the EPRI MULTEQ database. Predicting the stable chromium phases in a PWR is important as these constitute the compact inner oxide layer that forms on most ex-core alloys used in this system. Likewise understanding the chromium chemistry is necessary for rationalising high chromium content crud that has been observed on several plant fuel pins. Chromium (III) oxide solubility measurements have shown that the equilibrium solid phase under hydrothermal conditions is CrOOH rather than Cr 2 O 3 . Expressions for the solubility product of this solid and the equilibrium constant for the 4. Cr (III) hydrolysis reaction Cr (OH) 3 (aq) + H 2 O = Cr (OH) 4 - + H + have been derived by fitting to the experimental solubility data in neutral to alkaline solution. The equilibrium constant for the 3rd hydrolysis reaction Cr (OH) 2 + +H 2 O = Cr (OH) 3 (aq) + H + has been revised for consistency with literature estimates of the hydrolysis constants at 298 K. There are insufficient high-quality solubility data at low pH to derive the lower hydrolysis constants so the existing MULTEQ entries, based on thermodynamic estimations, have been retained. This revised model gave reasonable agreement with the available data in acidic solution. A revised expression for the Cr 2 O 3 solubility product was derived from measurements of Fe concentrations produced from FeCr 2 O 4 dissolution, and this was used to obtain a consistent solubility product expression for FeCr 2 O 4 . The resulting model predicts that FeCr 2 O 4 would be unstable at temperatures

Investigation of the solubility and diffusion of Fe atoms in Cu at high temperature using molten salt electrochemistry

International Nuclear Information System (INIS)

Wenzl, H.; Sorajic, V.; Bischof, B.

1977-01-01

The electrochemical cell CuFesub(n)/KF, LiF, FeF 2 (molten solution)/Fe was used between 800 and 1,000 0 C to produce CuFesub(n) alloys of various copper rich compositions n by electrochemically controlled diffusion. From measurements of cell voltage and current we determined composition, bulk diffusion coefficient D, and atomic solubility limit x 0 of Fe in Cu. The numerical values at the temperature of 950 0 C are D = 0.9 x 10 -9 cm 2 /sec, x 0 = 1.2 at%. (orig.) [de

Effect of atmospheric organic complexation on iron-bearing dust solubility

Directory of Open Access Journals (Sweden)

R. Paris

2013-05-01

Full Text Available Recent studies reported that the effect of organic complexation may be a potentially important process to be considered by models estimating atmospheric iron flux to the ocean. In this study, we investigated this process effect by a series of dissolution experiments on iron-bearing dust in the presence or the absence of various organic compounds (acetate, formate, oxalate, malonate, succinate, glutarate, glycolate, lactate, tartrate and humic acid as an analogue of humic like substances, HULIS typically found in atmospheric waters. Only 4 of tested organic ligands (oxalate, malonate, tartrate and humic acid caused an enhancement of iron solubility which was associated with an increase of dissolved Fe(II concentrations. For all of these organic ligands, a positive linear dependence of iron solubility to organic concentrations was observed and showed that the extent of organic complexation on iron solubility decreased in the following order: oxalate >malonate = tartrate > humic acid. This was attributed to the ability of electron donors of organic ligands and implies a reductive ligand-promoted dissolution. This study confirms that among the known atmospheric organic binding ligands of Fe, oxalate is the most effective ligand promoting dust iron solubility and showed, for the first time, the potential effect of HULIS on iron dissolution under atmospheric conditions.

Simple concentration-dependent pair interaction model for large-scale simulations of Fe-Cr alloys

International Nuclear Information System (INIS)

Levesque, Maximilien; Martinez, Enrique; Fu, Chu-Chun; Nastar, Maylise; Soisson, Frederic

2011-01-01

This work is motivated by the need for large-scale simulations to extract physical information on the iron-chromium system that is a binary model alloy for ferritic steels used or proposed in many nuclear applications. From first-principles calculations and the experimental critical temperature we build a new energetic rigid lattice model based on pair interactions with concentration and temperature dependence. Density functional theory calculations in both norm-conserving and projector augmented-wave approaches have been performed. A thorough comparison of these two different ab initio techniques leads to a robust parametrization of the Fe-Cr Hamiltonian. Mean-field approximations and Monte Carlo calculations are then used to account for temperature effects. The predictions of the model are in agreement with the most recent phase diagram at all temperatures and compositions. The solubility of Cr in Fe below 700 K remains in the range of about 6 to 12%. It reproduces the transition between the ordering and demixing tendency and the spinodal decomposition limits are also in agreement with the values given in the literature.

Correlation between ionic size and valence state of tetra, penta and hexavalent B-site substitution with solubility limit, phase transformation and multiferroic properties of Bi0.875Eu0.125FeO3

Science.gov (United States)

Mumtaz, Fiza; Jaffari, G. Hassnain; Hassan, Qadeer ul; Shah, S. Ismat

2018-06-01

We present detailed comparative study of effect of isovalent i.e. Eu+3 substitution at A-site and tetra (Ti+4, Zr+4), penta (V+5) and hexavalent (W+6) substitutions at B-site in BiFeO3. Eu+3 substitution led to phase transformation and exhibited mixed phases i.e. rhombohedral and orthorhombic, while tetravalent substituents (Ti+4 and Zr+4) led to stabilization of cubic phase. In higher valent (i.e. V+5 and W+6) cases solubility limit was significantly reduced where orthorhombic phase was observed as in the case of parent compound. Phase transformation as a consequence of increase in microstrain and chemical pressure induced by the substituent has been discussed. Solubility limit of different B-site dopants i.e. Zr, W and V was extracted to 5%, 2% and 2%, respectively. Extra phases in various cases were Bi2Fe4O9, Bi25FeO40, Bi14W2O27, and Bi23V4O44.5 and their fractional amount have been quantified. Ti was substituted up to 15% and has been observed to be completely soluble in the parent compound. Solubility limits depends on ionic radii mismatch and valance difference of Fe+3 and dopant, in which valance difference plays more dominant role. Solubility limit and phase transformation has been explained in terms of change in bond strength and tolerance factor induced by incorporation of dopant which depend on its size and valence state. Detail optical, dielectric, ferroelectric, magnetic and transport properties of Eu and Ti co-doped samples and selected low concentration B-site doped compositions (i.e. 2%) have presented and discussed. Two d-d transitions and three charge transfer transitions were observed within UV-VIS range. Both change in cell volume for the same phase and transformation in crystal structure affects the band gap. Increase in room temperature dielectric constant and saturation polarization was also found to increase in case of Eu-Ti co-doped samples with increasing concentration of Ti. Substitution of Eu at A-site and Ti at B-site led to

Chemical characterisation of iron in dust and biomass burning aerosols during AMMA-SOP0/DABEX: implication for iron solubility

Directory of Open Access Journals (Sweden)

R. Paris

2010-05-01

Full Text Available The chemical composition and the soluble fraction were determined in aerosol samples collected during flights of AMMA-SOP0/DABEX campaign, which were conducted in the West African Sahel during dry season (2006. Two aerosol types are encountered in this period: dust particles (DUST and biomass burning aerosol (BB. Chemical analysis and microscope observations showed that the iron (Fe found in BB samples mainly originates from dust particles mostly internally mixed in the biomass burning layer. Chemical analyses of samples showed that the Fe solubility is lower in African dust samples than in biomass burning aerosols. Our data provide a first idea of the variability of iron dust solubility in the source region (0.1% and 3.4%. We found a relationship between iron solubility/clay content/source which partly confirms that the variability of iron solubility in this source region is related to the character and origin of the aerosols themselves. In the biomass burning samples, no relationship were found between Fe solubility and either the concentrations of acidic species (SO₄²⁻, NO₃⁻ or oxalate or the content of carbon (TC, OC, BC. Therefore, we were unable to determine what processes are involved in this increase of iron solubility. In terms of supply of soluble Fe to oceanic ecosystems on a global scale, the higher solubility observed for Fe in biomass burning could imply an indirect source of Fe to marine ecosystems. But these aerosols are probably not significant because the Sahara is easily the dominant source of Fe to the Atlantic Ocean.

Solubility database for TILA-99

Energy Technology Data Exchange (ETDEWEB)

Vuorinen, U.; Carlsson, T. [VTT Chemical Technology, Espoo (Finland); Kulmala, S.; Hakanen, M. [Helsinki Univ. (Finland). Lab. of Radiochemistry; Ahonen, L. [Geological Survey of Finland, Espoo (Finland)

1998-11-01

The safety assessment of spent fuel disposal requires solubility values for several elements estimated in Finnish disposal conditions. In Finland four sites (Haestholmen, Kivetty, Olkiluoto and Romuvaara) are investigated for the disposal of spent fuel. Haestholmen and OLkiluoto are onshore sites, while Kivetty and Romuvaara are inland sites. Based on groundwater analysis and classification according to salinity at the planned disposal depth mainly fresh groundwater is encountered at Kivetty and Romuvaara, while brackish and saline water-types are met at Haestholmen and Olkiluoto. Very saline, almost brine-type water ({approx}70 g/l) has been found in the deepest parts of the investigated bedrock at one of the sites (Olkiluoto). The reference waters and conditions were chosen according to the water-types. The considered reference conditions incorporated both the near- and far-field, and both oxidizing and reducing conditions were considered. In the reference conditions, the changes in solubilities were also estimated as caused by possible variations in the pH, carbonate content and redox conditions. Uranium, which is the main component of spent fuel is dealt with in a separate report presenting the solubility of uranium and spent fuel dissolution. In this work the solubilities of all the other elements of concern (Am, Cu, Nb, Np, Pa, Pd, Pu, Ra, Se, Sn, Tc, Zr, Cm, Ni, Sr, Th, C, Cl, Cs, Fe, Ho, I, and Sm) in the safety assessment are considered. Some discussion on the corrosion of the spent fuel canister is also presented. For the estimation of solubilities of the elements in question, literature data was collected that mainly comprised experimentally measured concentrations. The sources used were spent fuel experiments, concentrations measured in solubility measurements, natural concentrations and concentrations from natural analogue sites (especially Palmottu and Hyrkkoelae in Finland) as well as the concentrations measured at the Finnish investigation sites

Solubility database for TILA-99

International Nuclear Information System (INIS)

Vuorinen, U.; Carlsson, T.; Kulmala, S.; Hakanen, M.

1998-11-01

The safety assessment of spent fuel disposal requires solubility values for several elements estimated in Finnish disposal conditions. In Finland four sites (Haestholmen, Kivetty, Olkiluoto and Romuvaara) are investigated for the disposal of spent fuel. Haestholmen and OLkiluoto are onshore sites, while Kivetty and Romuvaara are inland sites. Based on groundwater analysis and classification according to salinity at the planned disposal depth mainly fresh groundwater is encountered at Kivetty and Romuvaara, while brackish and saline water-types are met at Haestholmen and Olkiluoto. Very saline, almost brine-type water (∼70 g/l) has been found in the deepest parts of the investigated bedrock at one of the sites (Olkiluoto). The reference waters and conditions were chosen according to the water-types. The considered reference conditions incorporated both the near- and far-field, and both oxidizing and reducing conditions were considered. In the reference conditions, the changes in solubilities were also estimated as caused by possible variations in the pH, carbonate content and redox conditions. Uranium, which is the main component of spent fuel is dealt with in a separate report presenting the solubility of uranium and spent fuel dissolution. In this work the solubilities of all the other elements of concern (Am, Cu, Nb, Np, Pa, Pd, Pu, Ra, Se, Sn, Tc, Zr, Cm, Ni, Sr, Th, C, Cl, Cs, Fe, Ho, I, and Sm) in the safety assessment are considered. Some discussion on the corrosion of the spent fuel canister is also presented. For the estimation of solubilities of the elements in question, literature data was collected that mainly comprised experimentally measured concentrations. The sources used were spent fuel experiments, concentrations measured in solubility measurements, natural concentrations and concentrations from natural analogue sites (especially Palmottu and Hyrkkoelae in Finland) as well as the concentrations measured at the Finnish investigation sites. The

The calculated solubilities of hematite, magnetite and lepidocrocite in steam generator feedtrains

International Nuclear Information System (INIS)

Jobe, D.

1997-05-01

The solubility of three iron oxides [hematite (α-Fe 2 O 3 (s)), magnetite (Fe 3 O 4 (s)) and lepidocrocite (γ-FeOOH(s))] under representative steam generator feedtrain conditions were calculated using a thermodynamic database for these oxides and the associated aqueous species. Using this database, we calculated the solubility of iron for both Fe 3 O 4 (s) in equilibrium with other iron oxides and for the individual oxides in the presence of various oxygen partial pressures. The results indicate that the solubility of iron is strongly dependent on redox conditions, represented either by dissolved H 2 or O 2 concentration, or by the presence of other iron oxides (stable or metastable). The solubility behaviour of these oxides can be explained by changes in the aqueous-phase speciation of iron with temperature and pH. Similar calculations for the individual oxides in the presence Of O 2 (g) are also presented and were used to construct temperature-dependent phase diagrams for these oxides in equilibrium (including metastable conditions) with 1 ppb (ppb - μg·kg -1 ) of soluble iron. Calculations were also performed for feedtrain solutions containing 5 ppb of dissolved oxygen and pH buffered using mixtures of amines. From these calculations it was concluded that, relative to the oxidation potential and temperature of the feedtrain solution, changing the pH-buffer has only a minor effect on iron solubility. The effect of the variation in iron solubility along the feedtrain with solution pH, temperature and redox potential on corrosion-product transport to the boiler is also discussed. (author)

Nitrogen solubility in nickel base multicomponent melts

International Nuclear Information System (INIS)

Bol'shov, L.A.; Stomakhin, A.Ya.; Sokolov, V.M.; Teterin, V.G.

1984-01-01

Applicability of various methods for calculation of nitrogen solubility in high-alloyed nickel base alloys, containing Cr, Fe, W, Mo, Ti, Nb, has been estimated. A possibility is shown to use the formUla, derived for the calculation of nitrogen solubility in iron on the basis of statistical theory for a grid model of solution which does not require limitations for the content of a solvent component. The calculation method has been used for nickel alloys, with the concentration of solvent, iron, being accepted equal to zero, and employing parameters of nitrogen interaction as determined for iron-base alloys

Kinetics of microbial Fe(III) oxyhydroxidereduction: The role of mineral properties

NARCIS (Netherlands)

Bonneville, Steeve

2005-01-01

In many soils, sediments and groundwaters, ferric iron is a major potential electron acceptor for the oxidation of organic matter. In contrast to other terminal electron acceptors (e.g. nitrate or sulfate), the concentration of Fe3+(aq), is limited by the low solubility of Fe(III) oxyhydroxides

Predicting Soluble Nickel in Soils Using Soil Properties and Total Nickel.

Science.gov (United States)

Zhang, Xiaoqing; Li, Jumei; Wei, Dongpu; Li, Bo; Ma, Yibing

2015-01-01

Soil soluble nickel (Ni) concentration is very important for determining soil Ni toxicity. In the present study, the relationships between soil properties, total and soluble Ni concentrations in soils were developed in a wide range of soils with different properties and climate characteristics. The multiple regressions showed that soil pH and total soil Ni concentrations were the most significant parameters in predicting soluble Ni concentrations with the adjusted determination coefficients (Radj2) values of 0.75 and 0.68 for soils spiked with soluble Ni salt and the spiked soils leached with artificial rainwater to mimic field conditions, respectively. However, when the soils were divided into three categories (pH 8), they obtained better predictions with Radj2 values of 0.78-0.90 and 0.79-0.94 for leached and unleached soils, respectively. Meanwhile, the other soil properties, such as amorphous Fe and Al oxides and clay, were also found to be important for determining soluble Ni concentrations, indicating that they were also presented as active adsorbent surfaces. Additionally, the whole soil speciation including bulk soil properties and total soils Ni concentrations were analyzed by mechanistic speciation models WHAM VI and Visual MINTEQ3.0. It was found that WHAM VI provided the best predictions for the soils with pH 8. The Visual MINTEQ3.0 could provide better estimation for pH 8. These results indicated the possibility and applicability of these models to predict soil soluble Ni concentration by soil properties.

Treatment of reverse osmosis (RO) concentrate by the combined Fe/Cu/air and Fenton process (1stFe/Cu/air-Fenton-2ndFe/Cu/air).

Science.gov (United States)

Ren, Yi; Yuan, Yue; Lai, Bo; Zhou, Yuexi; Wang, Juling

2016-01-25

To decompose or transform the toxic and refractory reverse osmosis (RO) concentrate and improve the biodegradability, 1stFe/Cu/air-Fenton-2ndFe/Cu/air were developed to treat RO concentrate obtained from an amino acid production plant in northern China. First, their operating conditions were optimized thoroughly. Furthermore, 5 control experiments were setup to confirm the superiority of 1stFe/Cu/air-Fenton-2ndFe/Cu/air and synergistic reaction between Fe/Cu/air and Fenton. The results suggest that the developed method could obtain high COD removal (65.1%) and BOD5/COD ratio (0.26) due to the synergistic reaction between Fe/Cu/air and Fenton. Under the optimal conditions, the influent and effluent of 1stFe/Cu/air-Fenton-2ndFe/Cu/air and 5 control experiments were analyzed by using UV, FTIR, EEM and LC, which confirm the superiority of 1stFe/Cu/air-Fenton-2ndFe/Cu/air. Therefore, the developed method in this study is a promising process for treatment of RO concentrate. Copyright © 2015 Elsevier B.V. All rights reserved.

Kinetics of microbial Fe(III) oxyhydroxide reduction : The role of mineral properties

NARCIS (Netherlands)

Bonneville, S.C.

2005-01-01

In many soils, sediments and groundwaters, ferric iron is a major potential electron acceptor for the oxidation of organic matter. In contrast to other terminal electron acceptors (e.g. nitrate or sulfate), the concentration of Fe3+(aq), is limited by the low solubility of Fe(III) oxyhydroxides

Semen quality and concentration of soluble proteins in the seminal plasma of Alpine bucks Semen quality and concentration of soluble proteins in the seminal plasma of Alpine bucks

Directory of Open Access Journals (Sweden)

Simone Eliza Facione Guimarães

2010-06-01

Full Text Available It was aimed to study the in vitro seminal quality analyzed by complementary tests and to compare them with physical, morphological and biochemical aspects of male goat semen of the Alpine breed. This experiment took place at the Federal University of Viçosa, situated at 20º45’ S latitude and 42º51’ W longitude, Southwest of Brazil. It was done during the summer months of January and February, and three adult male goats of the Alpine breed were used in intensive conditions. The semen was collected by artificial vagina method. In all semen samples (45 ejaculates, after the physical and morphological analysis, the hiposmotic test was done. In 24 ejaculates, it were done thermo-resistance test, and in 21 ejaculates it were determined the concentration of total soluble proteins in seminal plasma. The male goats presented difference in the semen physical and morphological aspects, in the hiposmotic test and thermo-resistance test, but they did not presented difference in total soluble proteins concentration in seminal plasma. Results of the slow thermo-resistance test and hiposmotic test were positively correlated (r = 0.60. It was concluded, according to our results, that the concentration of total soluble proteins in seminal plasma can not be used as a parameter to predict the seminal quality of Alpine bucks.It was aimed to study the in vitro seminal quality analyzed by complementary tests and to compare them with physical, morphological and biochemical aspects of male goat semen of the Alpine breed. This experiment took place at the Federal University of Viçosa, situated at 20º45’ S latitude and 42º51’ W longitude, Southwest of Brazil. It was done during the summer months of January and February, and three adult male goats of the Alpine breed were used in intensive conditions. The semen was collected by artificial vagina method. In all semen samples (45 ejaculates, after the physical and morphological analysis, the hiposmotic test

In Situ Packaging FeFx into Sack-like Carbon Nanoreactors: A Smart Way To Make Soluble Fluorides Applicable to Aqueous Batteries.

Science.gov (United States)

Jiang, Jian; Li, Linpo; Xu, Maowen; Zhu, Jianhui; Li, Chang Ming

2016-02-17

Ferruginous materials have long attracted great interest in aqueous batteries since Fe is an earth-abundant and low toxic element. However, their practical application is severely hindered by their poor structural stability during deep cycling. To maximize their cyclability, we herein propose a simple and effective method, by in situ packaging Fe-based materials into carbon nanosacks via a facile CVD approach. To verify our strategy, we purposely choose water-soluble Fe2F5 as a study paradigm. The in situ formed Fe2F5@C nanosacks product exhibits prominent anodic performance with high electrochemical activity and capacity, obviously prolonged cyclic lifetime, and outstanding rate capabilities. Besides, by pairing with the cathode of α-Co(OH)2 nanowire arrays@carbon cloth, a full device of rechargeable aqueous batteries has been developed, capable to deliver both high specific energy and power densities (Max. values reaching up to ∼163 Wh kg(-1) and ∼14.2 kW kg(-1)), which shows great potential in practical usage. Our present work may not only demonstrate the feasibility of using soluble fluorides as anodes for aqueous batteries but also provide a smart way to upgrade cyclic behaviors of Fe-based anodes.

Correlation of flow accelerated corrosion rate with iron solubility

International Nuclear Information System (INIS)

Fujiwara, K.; Domae, M.; Yoneda, K.; Inada, F.; Ohira, T.; Hisamune, K.

2011-01-01

Flow accelerated corrosion (FAC) of the carbon steel is one of the most important subjects in the coolant systems of the power plants. FAC is influenced by the composition of the material, the flow condition, temperature, and the water chemistry conditions. It is considered that the solubility of iron (Fe) is the most important factor in the water chemistry parameters affecting FAC. In the present study, the effects of temperature and pH on the Fe solubility were evaluated in consideration of the hydrolysis reactions of the ferrous iron, the dissolution equilibria of Fe 3 O 4 , FeO, and Fe(OH) 2 , and the charge balance. The correlation between the Fe solubility and the FAC behavior was discussed. It has been suggested that the product of the Fe solubility equilibrated with Fe 3 O 4 and the mass transfer coefficient can explain the temperature and pH dependence of FAC. These results indicate the presence of the magnetite on the surface of the carbon steel. Diffusion of the Fe from the saturated layer to the bulk solution determines the FAC rate from the water chemistry aspect.

Fe-solubility of Ni7S6 and Ni9S8: Thermodynamic analysis

International Nuclear Information System (INIS)

Waldner, P.

2011-01-01

Experimental data on phase equilibria have been used for thermodynamic analysis of the iron solubility of the nickel sulfides Ni 7 S 6 and Ni 9 S 8 . For both compounds, a two-sublattice approach within the framework of the compound energy formalism has been applied to perform Gibbs free energy modelling at 0.1 MPa total pressure consistently embedded in recent thermodynamic assessment studies of other iron-nickel-sulfides. The predicted maxima of iron solubility around 3 at% of Ni 7 S 6 and 5.5 at% of Ni 9 S 8 are confirmed by experimental data. The calculations of complex ternary phase relations with Fe-bearing Ni 7 S 6 and Ni 9 S 8 gain further improvement. The first internally consistent description of all thermodynamically stable phases known in the literature for the iron-nickel-sulfur system is completed.

Rate-induced solubility and suppression of the first-order phase transition in olivine LiFePO4.

Science.gov (United States)

Zhang, Xiaoyu; van Hulzen, Martijn; Singh, Deepak P; Brownrigg, Alex; Wright, Jonathan P; van Dijk, Niels H; Wagemaker, Marnix

2014-05-14

The impact of ultrahigh (dis)charge rates on the phase transition mechanism in LiFePO4 Li-ion electrodes is revealed by in situ synchrotron diffraction. At high rates the solubility limits in both phases increase dramatically, causing a fraction of the electrode to bypass the first-order phase transition. The small transforming fraction demonstrates that nucleation rates are consequently not limiting the transformation rate. In combination with the small fraction of the electrode that transforms at high rates, this indicates that higher performances may be achieved by further optimizing the ionic/electronic transport in LiFePO4 electrodes.

Supramolecular Host-Guest System as Ratiometric Fe3+ Ion Sensor Based on Water-Soluble Pillar[5]arene.

Science.gov (United States)

Yao, Qianfang; Lü, Baozhong; Ji, Chendong; Cai, Yang; Yin, Meizhen

2017-10-18

Developing a specific, ratiometric, and reversible detection method for metal ions is significant to guard against the threat of metal-caused environmental pollution and organisms poisoning. Here a supramolecular host-guest system (WP5⊃G) based on water-soluble pillar[5]arene (WP5) and water-soluble quaternized perylene diimide derivative (G) was constructed. Morphological transformation was achieved during the process of adding WP5 into G aqueous solution, and a fluorescence "turn-off" phenomenon was observed which was caused by supramolecular photoinduced electron transfer (PET). Meanwhile, hydrophobic effect and electrostatic interaction played important roles in this supramolecular process, which was confirmed by isothermal titration calorimeter (ITC) and ζ potential experiments. Furthermore, the supramolecular host-guest system could be a "turn-on" fluorescent probe for Fe 3+ ion detection through the process of interdicting supramolecular PET. Moreover, the Fe 3+ ion detection showed specific, ratiometric, and reversible performances with a detection limit of 2.13 × 10 -7 M, which might have great potentials in biological and environmental monitoring.

Leaching of copper concentrates using NaCl and soluble copper contributed by the own concentrate; Lixiviacion de concentrados de cobre utilizando NaCl y el cobre soluble aportado por el propio concentrado

Energy Technology Data Exchange (ETDEWEB)

Herrero, O.; Bernal, N.; Quiroz, R.; Fuentes, G.; Vinals, J.

2005-07-01

Leaching of copper concentrates using cupric chloro complexes, generated in situ by the reaction between Cu(II), aported by the soluble copper content of the concentrate, and sodium chloride in acid media was studied. The concentrate samples were obtained from mineral processing plants from Antofagasta, Chile. Chemical and mineralogical characterization from original concentrates was made. Typical variable such as a chloride concentration, soluble copper concentration, leaching time, solid percentage and temperature were studied. DRX and EDS analyzed some of the residues. the experimental results indicated that it is possible to obtain solutions having high copper content (15 to 35 g/L) and 2 to 5 g/L free acid in order to submit this solution directly to a solvent extraction stage. The leaching tests use common reactive and low cost such as sodium chloride and sulfuric acid. (Author) 16 refs.

Solubility of magnetite in high temperature water and an approach to generalized solubility computations

International Nuclear Information System (INIS)

Dinov, K.; Ishigure, K.; Matsuura, C.; Hiroishi, D.

1993-01-01

Magnetite solubility in pure water was measured at 423 K in a fully teflon-covered autoclave system. A fairly good agreement was found to exist between the experimental data and calculation results obtained from the thermodynamical model, based on the assumption of Fe 3 O 4 dissolution and Fe 2 O 3 deposition reactions. A generalized thermodynamical approach to the solubility computations under complex conditions on the basis of minimization of the total system Gibbs free energy was proposed. The forms of the chemical equilibria were obtained for various systems initially defined and successfully justified by the subsequent computations. A [Fe 3+ ] T -[Fe 2+ ] T phase diagram was introduced as a tool for systematic understanding of the magnetite dissolution phenomena in pure water and under oxidizing and reducing conditions. (orig.)

Investigations on uranyl nitrate solubility in nitric acid in different concentrations at temperatures of 50C

International Nuclear Information System (INIS)

Deigele, E.

1983-01-01

The solubility of uranyl nitrate was studied in nitric acid solutions of different concentrations at a temperature of 5 0 C. This temperature was chosen with a view to using water as coolant and to facilitate the handling of the strong acid solutions. Accurate curves were established by a multitude of accurate measurements in the high concentration range. Further solubility curves can be derived from this basic curve. Some of the precipitates in the interesting regions of the solubility curve were analyzed. (orig./EF) [de

Solubility of cobalt in primary circuit solutions

International Nuclear Information System (INIS)

Lambert, I.; Joyer, F.

1992-01-01

The solubility of cobalt ferrite (CoFe 2 O 4 ) was measured in PWR primary circuit conditions, in the temperature range 250-350 deg C, and the results were compared with the ones obtained on magnetite and nickel ferrite. As in the former cases, it was found that, in the prevailing primary circuit conditions, the solubility of the cobalt ferrite was minimum at temperatures around 300 deg C, for cobalt as well as for iron. The equilibrium iron concentration is significantly lower than in the case of magnetite. The results are discussed in relation with the POTHY code, based only on thermodynamic laws and data, used for the prediction of the primary circuit chemistry

Pressurized capillary electrochromatographic analysis of water-soluble vitamins by combining with on-line concentration technique.

Science.gov (United States)

Jia, Li; Liu, Yaling; Du, Yanyan; Xing, Da

2007-06-22

A pressurized capillary electrochromatography (pCEC) system was developed for the separation of water-soluble vitamins, in which UV absorbance was used as the detection method and a monolithic silica-ODS column as the separation column. The parameters (type and content of organic solvent in the mobile phase, type and concentration of electrolyte, pH of the electrolyte buffer, applied voltage and flow rate) affecting the separation resolution were evaluated. The combination of two on-line concentration techniques, namely, solvent gradient zone sharpening effect and field-enhanced sample stacking, was utilized to improve detection sensitivity, which proved to be beneficial to enhance the detection sensitivity by enabling the injection of large volumes of samples. Coupling electrokinetic injection with the on-line concentration techniques was much more beneficial for the concentration of positively charged vitamins. Comparing with the conventional injection mode, the enhancement in the detection sensitivities of water-soluble vitamins using the on-line concentration technique is in the range of 3 to 35-fold. The developed pCEC method was applied to evaluate water-soluble vitamins in corns.

Synthesis and influence of alkaline concentration on α-FeOOH ...

Indian Academy of Sciences (India)

-FeOOH nanorods having uniform morphology were synthesized by water bath process. X-ray diffraction and transmission electron microscopy revealed that the single-crystalline orthorhombic -FeOOH nanorods are about 10 nm in diameter and hundreds of nanometer in length. The effect of concentration of KOH on ...

Identification of Multiple Soluble Fe(III Reductases in Gram-Positive Thermophilic Bacterium Thermoanaerobacter indiensis BSB-33

Directory of Open Access Journals (Sweden)

Subrata Pal

2014-01-01

Full Text Available Thermoanaerobacter indiensis BSB-33 has been earlier shown to reduce Fe(III and Cr(VI anaerobically at 60°C optimally. Further, the Gram-positive thermophilic bacterium contains Cr(VI reduction activity in both the membrane and cytoplasm. The soluble fraction prepared from T. indiensis cells grown at 60°C was found to contain the majority of Fe(III reduction activity of the microorganism and produced four distinct bands in nondenaturing Fe(III reductase activity gel. Proteins from each of these bands were partially purified by chromatography and identified by mass spectrometry (MS with the help of T. indiensis proteome sequences. Two paralogous dihydrolipoamide dehydrogenases (LPDs, thioredoxin reductase (Trx, NADP(H-nitrite reductase (Ntr, and thioredoxin disulfide reductase (Tdr were determined to be responsible for Fe(III reductase activity. Amino acid sequence and three-dimensional (3D structural similarity analyses of the T. indiensis Fe(III reductases were carried out with Cr(VI reducing proteins from other bacteria. The two LPDs and Tdr showed very significant sequence and structural identity, respectively, with Cr(VI reducing dihydrolipoamide dehydrogenase from Thermus scotoductus and thioredoxin disulfide reductase from Desulfovibrio desulfuricans. It appears that in addition to their iron reducing activity T. indiensis LPDs and Tdr are possibly involved in Cr(VI reduction as well.

Correlation of flow accelerated corrosion rate with iron solubility

International Nuclear Information System (INIS)

Fujiwara, K.; Domae, M.; Yoneda, K.; Inada, F.; Ohira, T.; Hisamune, K.; Takiguchi, H.

2009-01-01

Flow Accelerated Corrosion (FAC) of carbon steel is one of the most important subjects in coolant systems of power plants. FAC is influenced by material, flow condition, temperature, and water chemistry. It is considered that solubility is the most important factor to determine the effect of water chemistry on FAC. In the present study, effect of specific oxide on FAC rate was studied from the thermodynamic solubility of iron. The effects of temperature and pH on the iron solubility were evaluated by taking into consideration hydrolysis reactions of ferrous iron, dissolution equilibria of Fe 3 O 4 , FeO, and Fe(OH) 2 , and charge balance. The correlation between the iron solubility and FAC behavior was evaluated by using the normalized mass transfer coefficient. It is clarified that the product of iron solubility equilibrated with Fe 3 O 4 and normalized mass transfer coefficient can explain the temperature and pH dependence of FAC. These results indicate presence of magnetite on the surface of carbon steel. Diffusion of iron from the saturated layer determines the FAC rate from water chemistry aspect. (author)

Temperature dependence of nitrogen solubility in iron base multicomponent melts

International Nuclear Information System (INIS)

Sokolov, V.M.; Koval'chuk, L.A.

1986-01-01

Method for calculating temperature dependence of nitrogen solubility in iron base multicomponent melts is suggested. Application areas of existing methods were determined and advantages of the new method for calculating nitrogen solubility in multicomponent-doped iron melts (Fe-Ni-Cr-Mo, Fe-Ni-Cr-Mn, Fe-Mo-V) at 1773-2073 K are shown

Dissolution behavior of Cu, Fe and Zn from gold sulfide concentrate during pre-oxidation using ozone in neutral media

Science.gov (United States)

Kurniawan, Mubarok, M. Zaki

2018-04-01

The aim of this work was to observe the dissolution behaviour of Cu, Fe and Zn from gold sulfide concentrate during preoxidation with ozone as the oxidant and distillation water as the media. The preoxidation experiments were carried out in five-necked reactor with variations of retention time, percent solid, particle size and oxygen dosage injected to ozone generator. The retention time was varied at 6 hours, 8 hours, 12 hours and 24 hours. The percent solid was varied at 10%, 20% and 30% while the particle size was varied at P80 -75 mesh dan P80 -20 mesh. The dosage of oxygen injection to ozone generator was varried at 1 liter per minute and 2 liter per minute. The ozone gas was produced by using ozone generator type OZ-03 and injected to the slurry by using Mazzei injector. The soluble Cu, Fe and Zn were measured by using Atomic Absorption Spectrophotometry (AAS). The concentrates were characterized by X-Ray Diffraction (XRD), mineragraphy, fire assay and Inductively Coupled Plasma (ICP). Fire assay, ICP and XRD were used to analyse the residues and froth. The solubilition of metals (Cu, Fe and Zn) was obtained through the formation of sulphate ion and H+ which decreased the pH, released a number of heat and then was continued by the formation of elemental sulphur (S°). The interaction of particles and gas yielded the formation of froth. The highest dissolution percentage of Cu, Fe and Zn was achieved through 24 hours oxidation at 20% (w/w), P80 -20 mesh and one liter per minute of oxygen injection dosage by 83.016%, 24.7303% and 91.6808%, respectively.

Solubility of iron from combustion source particles in acidic media linked to iron speciation.

Science.gov (United States)

Fu, Hongbo; Lin, Jun; Shang, Guangfeng; Dong, Wenbo; Grassian, Vichi H; Carmichael, Gregory R; Li, Yan; Chen, Jianmin

2012-10-16

In this study, iron solubility from six combustion source particles was investigated in acidic media. For comparison, a Chinese loess (CL) dust was also included. The solubility experiments confirmed that iron solubility was highly variable and dependent on particle sources. Under dark and light conditions, the combustion source particles dissolved faster and to a greater extent relative to CL. Oil fly ash (FA) yielded the highest soluble iron as compared to the other samples. Total iron solubility fractions measured in the dark after 12 h ranged between 2.9 and 74.1% of the initial iron content for the combustion-derived particles (Oil FA > biomass burning particles (BP) > coal FA). Ferrous iron represented the dominant soluble form of Fe in the suspensions of straw BP and corn BP, while total dissolved Fe presented mainly as ferric iron in the cases of oil FA, coal FA, and CL. Mössbauer measurements and TEM analysis revealed that Fe in oil FA was commonly presented as nanosized Fe(3)O(4) aggregates and Fe/S-rich particles. Highly labile source of Fe in corn BP could be originated from amorphous Fe form mixed internally with K-rich particles. However, Fe in coal FA was dominated by the more insoluble forms of both Fe-bearing aluminosilicate glass and Fe oxides. The data presented herein showed that iron speciation varies by source and is an important factor controlling iron solubility from these anthropogenic emissions in acidic solutions, suggesting that the variability of iron solubility from combustion-derived particles is related to the inherent character and origin of the aerosols themselves. Such information can be useful in improving our understanding on iron solubility from combustion aerosols when they undergo acidic processing during atmospheric transport.

Concentrations of Mn and Fe in the Sediment Cores of Sarawak and Sabah Coastal Waters

International Nuclear Information System (INIS)

Zal Uyun Wan Mahmood; Zaharudin Ahmad; Che Abdul Rahim Mohamed

2010-01-01

Sediment cores were taken at eight stations along Sarawak and Sabah coastal waters using a gravity box corer on July 2004. The sediment cores were cut into 2 cm interval for measurement of Mn and Fe concentration using the Inductive Couple Plasma-Mass Spectrometer (ICP-MS). Overall, the sediment cores contained much mud which include a mixture of silt (46 - 67 %) and clay (18 - 53 %) compared to sand (0.4 - 16 %). The concentrations of Mn and Fe were in the range of 154 - 366 μg/ g and 0.9 - 3.4 %, respectively. The variation was studied by ANOVA, which showed a significant difference (p = 0.000) for both of Mn and Fe concentrations at all sampling stations. In those ranges, Fe concentration was higher compared to Mn. It is believed that dissolving and diluting process influenced the concentration of Mn in the water column and sediment. Fe showed a significant correlation (r > 0.5, p geo < 1 and classification 0 - 1. (author)

Effect of the oxidation rate and Fe(II) state on microbial nitrate-dependent Fe(III) mineral formation

Science.gov (United States)

Senko, John M.; Dewers , Thomas A.; Krumholz, Lee R.

2005-01-01

A nitrate-dependent Fe(II)-oxidizing bacterium was isolated and used to evaluate whether Fe(II) chemical form or oxidation rate had an effect on the mineralogy of biogenic Fe(III) (hydr)oxides resulting from nitrate-dependent Fe(II) oxidation. The isolate (designated FW33AN) had 99% 16S rRNA sequence similarity to Klebsiella oxytoca. FW33AN produced Fe(III) (hydr)oxides by oxidation of soluble Fe(II) [Fe(II)sol] or FeS under nitrate-reducing conditions. Based on X-ray diffraction (XRD) analysis, Fe(III) (hydr)oxide produced by oxidation of FeS was shown to be amorphous, while oxidation of Fe(II)sol yielded goethite. The rate of Fe(II) oxidation was then manipulated by incubating various cell concentrations of FW33AN with Fe(II)sol and nitrate. Characterization of products revealed that as Fe(II) oxidation rates slowed, a stronger goethite signal was observed by XRD and a larger proportion of Fe(III) was in the crystalline fraction. Since the mineralogy of Fe(III) (hydr)oxides may control the extent of subsequent Fe(III) reduction, the variables we identify here may have an effect on the biogeochemical cycling of Fe in anoxic ecosystems.

450 {sup o}C isothermal section of the Fe-Zn-Si ternary phase diagram

Energy Technology Data Exchange (ETDEWEB)

Su, Xuping [Inst. of Materials Research, School of Mechanical Engineering, Xiangtan Univ., Xiangtan, Hunan (China); Univ. of Toronto, Dept. of Materials Science and Engineering, Toronto, Ontario (Canada); Tang, Nai-Yong [Cominco Ltd., Product Technology Centre, Mississauga, Ontario (Canada); Toguri, J.M. [Univ. of Toronto, Dept. of Materials Science and Engineering, Toronto, Ontario (Canada)

2001-07-01

The 450 {sup o}C isothermal section of the Fe-Zn-Si ternary phase diagram has been determined experimentally using optical microscopy, scanning electron microscopy (SEM) coupled with energy dispersive X-ray spectroscopy (EDS) and X-ray diffractometry. The focus of the work has been concentrated on the Zn-rich corner which is relevant to general galvanizing. The present study has confirmed the existence of the equilibrium state between the liquid, the {zeta} phase and the FeSi phase. This three phase equilibrium state prevents the equilibrium between the liquid and the {delta} phase suggested by some researchers. Experimental results indicate that Si solubility in all four binary Zn-Fe compounds is limited. The Fe solubility in molten Zn was found to decrease with increasing Si content in the melt. The liquid phase boundary was determined using a model based phenomenological approach. (author)

Human Intestinal Fluid Layer Separation: The Effect On Colloidal Structures & Solubility Of Lipophilic Compounds.

Science.gov (United States)

Danny, Riethorst; Amitava, Mitra; Filippos, Kesisoglou; Wei, Xu; Jan, Tack; Joachim, Brouwers; Patrick, Augustijns

2018-05-23

In addition to individual intestinal fluid components, colloidal structures are responsible for enhancing the solubility of lipophilic compounds. The present study investigated the link between as well as the variability in the ultrastructure of fed state human intestinal fluids (FeHIF) and their solubilizing capacity for lipophilic compounds. For this purpose, FeHIF samples from 10 healthy volunteers with known composition and ultrastructure were used to determine the solubility of four lipophilic compounds. In light of the focus on solubility and ultrastructure, the study carefully considered the methodology of solubility determination in relation to colloid composition and solubilizing capacity of FeHIF. To determine the solubilizing capacity of human and simulated intestinal fluids, the samples were saturated with the compound of interest, shaken for 24 h, and centrifuged. When using FeHIF, solubilities were determined in the micellar layer of FeHIF, i.e. after removing the upper (lipid) layer (standard procedure), as well as in 'full' FeHIF (without removal of the upper layer). Compound concentrations were determined using HPLC-UV/fluorescence. To link the solubilizing capacity with the ultrastructure, all human and simulated fluids were imaged using transmission electron microscopy (TEM) before and after centrifugation and top layer (lipid) removal. Comparing the ultrastructure and solubilizing capacity of individual FeHIF samples demonstrated a high intersubject variability in postprandial intestinal conditions. Imaging of FeHIF after removal of the upper layer clearly showed that only micellar structures remain in the lower layer. This observation suggests that larger colloids such as vesicles and lipid droplets are contained in the upper, lipid layer. The solubilizing capacity of most FeHIF samples substantially increased with inclusion of this lipid layer. The relative increase in solubilizing capacity upon inclusion of the lipid layer was most pronounced

Role of metal ion solubility in leaching of nuclear waste glasses

International Nuclear Information System (INIS)

Grambow, B.

1982-04-01

From the results of a variety of experiments it can be concluded that reaction of the matrix is the fundamental process that occurs in the leaching of PNL 76-68 glass. This reaction has two aspects. Without solubility restrictions, congruent leaching behavior occurs at all pH values and leachant compositions. When this reaction raises solution concentrations of certain elements to the level at which new solid phases form, these phases will regulate the solution concentration. These solid phases are dominant constituents of the leached layer. For the leaching of PNL 76-68 glass, the solubilities of these reaction products regulate the solution concentration as if the solution is in equilibrium with pure Fe(OH) 3 (amorphous), Zn(OH) 2 (amorphous), Nd(OH) 3 , SrCO 3 or CaCO 3 . The experimental conditions, in particular the pH value, that govern the formation of solid reaction products and control of the solution concentrations can be identified

Neptunium (IV) oxalate solubility

International Nuclear Information System (INIS)

Luerkens, D.W.

1983-07-01

The equilibrium solubility of neptunium (IV) oxalate in nitric/oxalic acid solutions was determined at 22 0 C, 45 0 C, and 60 0 C. The concentrations of nitric/oxalic acid solutions represented a wide range of free oxalate ion concentration. A mathematical solubility model was developed which is based on the formation of the known complexes of neptunium (IV) oxalate. the solubility model uses a simplified concentration parameter which is proportional to the free oxalate ion concentration. The solubility model can be used to estimate the equilibrium solubility of neptunium (IV) oxalate over a wide range of oxalic and nitric acid concentrations at each temperature

Heat capacity and solid solubility of iron in scandium

International Nuclear Information System (INIS)

Tsang, T.-W.E.

1981-01-01

The maximum solid solubility of iron in scandium was determined to be between 50 and 85 at.ppm in the as-cast condition. As the concentration of iron increases, it segregates along the grain boundary, as is evident from optical metallography and electron microprobe examinations. Annealing also causes the iron dissolved in scandium to separate out and cluster along the grain boundary. Heat capacity measurements show an anomaly in the C/T versus T 2 plots for iron concentrations of 19 at.ppm or greater. For iron dissolved in solid scandium the excess entropy due to the iron impurity is in agreement with the theoretical prediction of ck ln(2S + 1) for an impurity-conduction electron (Kondo) interaction, but is 4 - 8 times larger than the theoretical prediction when iron segregates along the grain boundary. Furthermore, our results suggest that most of the previously reported low temperature physical properties of scandium are probably in error because of either iron impurity-conduction electron interactions or Fe-Fe interactions in the precipitated second-phase Sc-Fe compound. (Auth.)

Fe concentration dependence of tunneling magnetoresistance in magnetic tunnel junctions using group-IV ferromagnetic semiconductor GeFe

Directory of Open Access Journals (Sweden)

Kosuke Takiguchi

2017-10-01

Full Text Available Group-IV-based ferromagnetic semiconductor Ge1−xFex (GeFe is one of the most promising materials for spin injection/detection in Si and Ge. In this paper, we demonstrate a systematic study of tunneling magnetoresistance (TMR in magnetic tunnel junctions (MTJs composed of Fe/MgO/Ge1−xFex with various Fe concentrations (x = 0.065, 0.105, 0.140, and 0.175. With increasing x, the TMR ratio increases up to 1.5% when x≤ 0.105, and it decreases when x> 0.105. This is the first observation of the TMR ratio over 1% in MTJs containing a group-IV ferromagnetic semiconductor. With increasing x, while the Curie temperature of GeFe increases, the MgO surface becomes rougher, which is thought to be the cause of the upper limit of the TMR ratio. The quality of the MgO layer on GeFe is an important factor for further improvement of TMR in Fe/MgO/GeFe MTJs.

Effect of Fe ion concentration on corrosion of carbon steel in CO2 environment

DEFF Research Database (Denmark)

Rogowska, Magdalena; Gudme, J.; Rubin, A.

2016-01-01

In this work, the corrosion behaviour of steel wires in solutions containing different concentrations of Fe2+ was investigated by the linear polarisation resistance method, while the evolution of pH was monitored in situ and changes of the Fe2+ concentration were monitored ex situ. Characterisation...

Hydrothermal ore-forming processes in the light of studies in rock- buffered systems: I. Iron-copper-zinc-lead sulfide solubility relations

Science.gov (United States)

Hemley, J.J.; Cygan, G.L.; Fein, J.B.; Robinson, G.R.; d'Angelo, W. M.

1992-01-01

Experimental studies, using cold-seal and extraction vessel techniques, were conducted on Fe, Pb, Zn, and Cu sulfide solubilities in chloride soultions at temperatures from 300?? to 700??C and pressures from 0.5 to 2 kbars. The solutions were buffered in pH by quartz monzonite and the pure potassium feldspar-muscovite-quartz assemblage and in fS2-fO2 largely by the assemblage pyrite-pyrrhotite-magnetite. Solubilities increase with increasing temperature and total chloride, and decrease with increasing pressure. The effect of increasing chloride concentration on solubility reflects primarily a shift to lower pH via the silicate buffer reactions. Similarity in behaviour with respect to the temperature and pressure of Fe, Zn, and Pb sulfide solubilities points to similarity in chloride speciation, and the neutral species appear to be dominant in the high-temperature region. -from Authors

Extractable trace elements and sodium in Illinois coal-cleaning wastes: correlation with concentrations in tall fescue

Energy Technology Data Exchange (ETDEWEB)

Lewis, B.G.

1983-07-01

Trace element concentrations in shoots of tall fescue (Festuca arundinacea Schreb.) were correlated with extractable element concentrations in five southern Illinois coal-cleaning wastes limed to pH 6.5, in a greenhouse study to determine applicability of soil tests to coal-waste evaluation. There was little or no correlation between shoot concentrations of Fe, and Fe extracted from the wastes by dilute acid (r equals 0.60), DTPA at pH 6.4 (r equals 0.47) or DTPA at pH 8.4 (r equals -0.17). The corresponding r values for Mn were 0.94, 0.97, and 0.96; for Zn, 0.96, 0.96, and 0.88; and for Cu, 0.67, 0.90, and 0.88, respectively. Shoot B correlated well with hot water-soluble B(r equals 0.96) and acid-soluble B(r equals 0.91). Correlations for shoot Na were also good with water-soluble Na and acid-soluble Na (r equals 0.96 in both cases). Concentrations of Al, As, Cd, Ni, Pb, and Se in the shoots were well below reported upper critical levels, and similar to concentrations in the grass grown on a silt loam under the same greenhouse conditions. 21 references.

Determination of the solubility limiting solid of the selenium in the presence of iron under anoxic conditions

International Nuclear Information System (INIS)

Iida, Y.; Yamaguchi, T.; Tanaka, T.; Kitamura, A.; Nakayama, S.

2009-01-01

Dissolution experiments of selenium were performed from both under saturation and over saturation directions to determine the solubility limiting solid of selenium under the conditions which thermodynamically prefer the formation of ferroselite (FeSe 2 ). X-ray diffractometry (XRD) showed that FeSe 2 was formed in the over-saturation experiments. However, the ion activity products for the reaction of 0.5 FeSe 2 + H + + e - 0.5 Fe 2+ + HSe - , aFe 2+0.5 aHSe - a H+ -1 a e- -1 , obtained from both under saturation and over saturation directions were 3 to 4 orders of magnitude higher than the equilibrium constants calculated from existing thermodynamic data. The dependencies of the selenium concentration on pH, Eh and the iron concentration were better interpreted as a dissolution reaction of selenium solid (Se(s)) than the iron-selenium compounds. The equilibrium constant of: Se(s) + H + + 2e - = HSe - was determined to be logK 0 -7.46±0.11. This value agrees with the value of logK 0 = -7.62±0.06 calculated from existing thermodynamic data of crystalline selenium within errors. Because crystalline selenium was not identified in the solid phases by XRD, the solubility limiting solid would be amorphous or minor amount of crystalline selenium, even if the iron-selenium compound was formed. (authors)

The potential impact of microbial Fe(III) reduction on subsurface U(VI) mobility at a low level radioactive waste storage site

International Nuclear Information System (INIS)

Wilkins, M.J.; Livens, F.R.; Vaughan, D.J.; Lloyd, J.R.; Beadle, I.; Small, J.S.

2005-01-01

Full text of publication follows: Fe(III) oxy-hydroxides have the potential to be utilised as terminal electron acceptors by indigenous microbial communities in the British Nuclear Fuels (BNFL) low level radioactive waste storage site at Drigg (Cumbria, UK) and these organisms may have a critical control on the biogeochemical cycling of several environmentally important radionuclides. In terms of radiological impact at Drigg, uranium is the most significant contributor to radiological impact and it is strongly influenced by biogeochemical processes. In terms of mass (moles) it is also the most abundant radionuclide in the Drigg inventory. Thus, the potential biotic and abiotic effects of Fe(III) reduction on U(VI) mobility in the Drigg subsurface are of interest. Culture-dependent and molecular techniques showed that the sediments in and around the Drigg site contained a diversity of Fe(III)-reducing bacteria. A series of microcosm experiments were utilised to create environmentally relevant experimental conditions. Microcosms set up using Drigg sediment and synthetic ground water were spiked with 100 μM U(VI) and acetate as an electron donor. U(VI) concentrations in groundwater were measured using a chemical assay while total U levels were determined using ICP-MS. Fe(II) levels were determined using the ferrozine method. Sediment surface areas were measured using BET analysis. The low surface area of the sediments resulted in only a small proportion of the 100 μM U(VI) spike sorbing onto mineral surfaces. The addition of ferri-hydrite to some microcosms resulted in an immediate lowering of soluble U(VI) concentrations, suggesting that the formation of soluble U(VI) complexes were not responsible for the minimal adsorption. The presence of biogenic Fe(II) in the microcosms did not affect the soluble U(VI) concentration. Similarly, soluble U(VI) levels remained unchanged when sediments were spiked with U(VI) post-microbial Fe(III) reduction. However, a lowering in

Preparation and characterization of highly water-soluble magnetic Fe3O4 nanoparticles via surface double-layered self-assembly method of sodium alpha-olefin sulfonate

International Nuclear Information System (INIS)

Li, Honghong; Qin, Li; Feng, Ying; Hu, Lihua; Zhou, Chunhua

2015-01-01

A kind of double-layered self-assembly sodium alpha-olefin sulfonate (AOS) capped Fe 3 O 4 magnetic nanoparticles (Fe 3 O 4 -AOS-MN) with highly water-solubility was prepared by a wet co-precipitation method with a pH of 4.8. The resulting Fe 3 O 4 -AOS-MN could be dispersed into water to form stable magnetic fluid without other treatments. The result of X-ray diffraction (XRD) indicated that the Fe 3 O 4 -AOS-MN maintained original crystalline structure and exhibited a diameter of about 7.5 nm. The iron oxide phase of nanoparticles determined by Raman spectroscopy is Fe 3 O 4 . Transmission electron microscopy (TEM) analysis confirmed that the Fe 3 O 4 -AOS-MN with spherical morphology were uniformly dispersed in water. FT-IR spectroscopy (FT-IR) and thermo-gravimetric analysis (TGA) verified the successful preparation of Fe 3 O 4 -AOS-MN capped with double-layered self-assembled AOS. The corresponding capacities of monolayer chemical absorption and the second-layer self-assembly absorption were respectively 4.07 and 14.71 wt% of Fe 3 O 4 -MN, which were much lower than those of other surfactants. Vibrating sample magnetometer (VSM) test result showed Fe 3 O 4 -AOS-MN possessed superparamagnetic behavior with the saturation magnetization value of about 44.45 emu/g. The blocking temperature T B of Fe 3 O 4 -AOS-MN capped with double-layered AOS is 170 K. - Highlights: • Double-layered self-assembly sodium alpha-olefin sulfonate (AOS) capped Fe 3 O 4 magnetic nanoparticles are prepared by a wet co-precipitation method. • Double-layered Fe 3 O 4 -AOS-MN exhibits highly water-solubility. • The iron oxide phase is determined by Raman spectroscopy. • Fe 3 O 4 -AOS-MN capped with double-layered AOS possesses super-paramagnetic behavior. • The blocking temperature T B of Fe 3 O 4 -AOS-MN capped with double-layered AOS is 170 K

From solid solution to cluster formation of Fe and Cr in α-Zr

International Nuclear Information System (INIS)

Burr, P.A.; Wenman, M.R.; Gault, B.; Moody, M.P.; Ivermark, M.; Rushton, M.J.D.; Preuss, M.; Edwards, L.; Grimes, R.W.

2015-01-01

To understand the mechanisms by which the re-solution of Fe and Cr additions increase the corrosion rate of irradiated Zr alloys, the solubility and clustering of Fe and Cr in model binary Zr alloys was investigated using a combination of experimental and modelling techniques — atom probe tomography (APT), x-ray diffraction (XRD), thermoelectric power (TEP) and density functional theory (DFT). Cr occupies both interstitial and substitutional sites in the α-Zr lattice; Fe favours interstitial sites, and a low-symmetry site that was not previously modelled is found to be the most favourable for Fe. Lattice expansion as a function of Fe and Cr content in the α-Zr matrix deviates from Vegard's law and is strongly anisotropic for Fe additions, expanding the c-axis while contracting the a-axis. Matrix content of solutes cannot be reliably estimated from lattice parameter measurements, instead a combination of TEP and APT was employed. Defect clusters form at higher solution concentrations, which induce a smaller lattice strain compared to the dilute defects. In the presence of a Zr vacancy, all two-atom clusters are more soluble than individual point defects and as many as four Fe or three Cr atoms could be accommodated in a single Zr vacancy. The Zr vacancy is critical for the increased apparent solubility of defect clusters; the implications for irradiation induced microstructure changes in Zr alloys are discussed.

From solid solution to cluster formation of Fe and Cr in α-Zr

Energy Technology Data Exchange (ETDEWEB)

Burr, P.A., E-mail: burr.patrick@gmail.com [Centre for Nuclear Engineering and Department of Materials, Imperial College London, London, SW7 2AZ (United Kingdom); Institute of Materials Engineering, Australian Nuclear Science & Technology Organisation, Menai, New South Wales 2234 (Australia); Wenman, M.R. [Centre for Nuclear Engineering and Department of Materials, Imperial College London, London, SW7 2AZ (United Kingdom); Gault, B.; Moody, M.P. [Department of Materials, University of Oxford, Parks Road, Oxford, OX1 3PH (United Kingdom); Ivermark, M. [High Temperature Materials, Sandvik Materials Technology, 734 27 Hallstahammar (Sweden); University of Manchester, School of Materials, M13 9PL (United Kingdom); Rushton, M.J.D. [Centre for Nuclear Engineering and Department of Materials, Imperial College London, London, SW7 2AZ (United Kingdom); Preuss, M. [University of Manchester, School of Materials, M13 9PL (United Kingdom); Edwards, L. [Institute of Materials Engineering, Australian Nuclear Science & Technology Organisation, Menai, New South Wales 2234 (Australia); Grimes, R.W. [Centre for Nuclear Engineering and Department of Materials, Imperial College London, London, SW7 2AZ (United Kingdom)

2015-12-15

To understand the mechanisms by which the re-solution of Fe and Cr additions increase the corrosion rate of irradiated Zr alloys, the solubility and clustering of Fe and Cr in model binary Zr alloys was investigated using a combination of experimental and modelling techniques — atom probe tomography (APT), x-ray diffraction (XRD), thermoelectric power (TEP) and density functional theory (DFT). Cr occupies both interstitial and substitutional sites in the α-Zr lattice; Fe favours interstitial sites, and a low-symmetry site that was not previously modelled is found to be the most favourable for Fe. Lattice expansion as a function of Fe and Cr content in the α-Zr matrix deviates from Vegard's law and is strongly anisotropic for Fe additions, expanding the c-axis while contracting the a-axis. Matrix content of solutes cannot be reliably estimated from lattice parameter measurements, instead a combination of TEP and APT was employed. Defect clusters form at higher solution concentrations, which induce a smaller lattice strain compared to the dilute defects. In the presence of a Zr vacancy, all two-atom clusters are more soluble than individual point defects and as many as four Fe or three Cr atoms could be accommodated in a single Zr vacancy. The Zr vacancy is critical for the increased apparent solubility of defect clusters; the implications for irradiation induced microstructure changes in Zr alloys are discussed.

Elemental content in ground and soluble/instant coffee

International Nuclear Information System (INIS)

Vega-Carrillo, H.R.; Manzanares-Acuna, E.; Iskander, F.Y.

2002-01-01

The concentration of thirty-four elements in twelve coffee brands has been measured using instrumental neutron activation analysis. The samples investigated included four brands of commercially available ground coffee and eight brands of soluble/instant coffee. The elements measured were Al, As, Ba, Ca, Ce, Co, Cr, Cs, Dy, Eu, Fe, Gd, Hf, K, La, Lu, Mg, Mn, Na, Rb, Sb, Sc, Se, Sm, Sr, Ta, Tb, Th, Ti, Tm, U, V, Yb and Zn. Twenty four elements were found to be below the detection limit in one or more samples. These elements were Ce, Cr, Fe, V, As, Eu, Ba, Dy, Gd, Hf, La, Lu, Sb, Sc, Se, Sm, Sr, Ta, Tb, Th, Ti, Yb, Tm, and U. (author)

Stabilities of thiomolybdate complexes of iron; implications for retention of essential trace elements (Fe, Cu, Mo) in sulfidic waters.

Science.gov (United States)

Helz, George R; Erickson, Britt E; Vorlicek, Trent P

2014-06-01

In aquatic ecosystems, availabilities of Fe, Mo and Cu potentially limit rates of critical biological processes, including nitrogen fixation, nitrate assimilation and N2O decomposition. During long periods in Earth's history when large parts of the ocean were sulfidic, what prevented these elements' quantitative loss from marine habitats as insoluble sulfide phases? They must have been retained by formation of soluble complexes. Identities of the key ligands are poorly known but probably include thioanions. Here, the first determinations of stability constants for Fe(2+)-[MoS4](2-) complexes in aqueous solution are reported based on measurements of pyrrhotite (hexagonal FeS) solubility under mildly alkaline conditions. Two linear complexes, [FeO(OH)MoS4](3-) and [(Fe2S2)(MoS4)2](4-), best explain the observed solubility variations. Complexes that would be consistent with cuboid cluster structures were less successful, implying that such clusters probably are minor or absent in aqueous solution under the conditions studied. The new data, together with prior data on stabilities of Cu(+)-[MoS4](2-) complexes, are used to explore computationally how competition of Fe(2+) and Cu(+) for [MoS4](2-), as well as competition of [MoS4](2-) and HS(-) for both metals would be resolved in solutions representative of sulfidic natural waters. Thiomolybdate complexes will be most important at sulfide concentrations near the [MoO4](2-)-[MoS4](2-) equivalence point. At lower sulfide concentrations, thiomolybdates are insufficiently stable to be competitive ligands in natural waters and at higher sulfide concentrations HS(-) ligands out-compete thiomolybdates.

SITE-94. Radionuclide solubilities for SITE-94

Energy Technology Data Exchange (ETDEWEB)

Arthur, R.; Apted, M. [QuantiSci, Denver, CO (United States)

1996-12-01

In this report, solubility constraints are evaluated on radioelement source-term concentrations supporting the SITE-94 performance assessment. Solubility models are based on heterogeneous-equilibrium, mass- and charge-balance constraints incorporated into the EQ3/6 geochemical software package, which is used to calculate the aqueous speciation behavior and solubilities of U, Th, Pu, Np, Am, Ni, Ra, Se, Sn, Sr, Tc and Zr in site groundwaters and near-field solutions. The chemical evolution of the near field is approximated using EQ3/6 in terms of limiting conditions at equilibrium, or steady state, in three closed systems representing fully saturated bentonite, Fe{sup o} corrosion products of the canister, and spent fuel. The calculations consider both low-temperature (15 deg C) and high-temperature (80 deg C) conditions in the near field, and the existence of either reducing or strongly oxidizing conditions in each of the bentonite, canister, and spent-fuel barriers. Heterogeneities in site characteristics are evaluated through consideration of a range of initial groundwaters and their interactions with engineered barriers. Aqueous speciation models for many radioelements are constrained by thermodynamic data that are estimated with varying degrees of accuracy. An important question, however, is how accurate do these models need to be for purposes of estimating source-term concentrations? For example, it is unrealistic to expect a high degree of accuracy in speciation models if such models predict solubilities that are below the analytical detection limit for a given radioelement. From a practical standpoint, such models are irrelevant if calculated solubilities cannot be tested by direct comparison to experimental data. In the absence of models that are both accurate and relevant for conditions of interest, the detection limit could define a pragmatic upper limit on radioelement solubility 56 refs, 25 tabs, 10 figs

SITE-94. Radionuclide solubilities for SITE-94

International Nuclear Information System (INIS)

Arthur, R.; Apted, M.

1996-12-01

In this report, solubility constraints are evaluated on radioelement source-term concentrations supporting the SITE-94 performance assessment. Solubility models are based on heterogeneous-equilibrium, mass- and charge-balance constraints incorporated into the EQ3/6 geochemical software package, which is used to calculate the aqueous speciation behavior and solubilities of U, Th, Pu, Np, Am, Ni, Ra, Se, Sn, Sr, Tc and Zr in site groundwaters and near-field solutions. The chemical evolution of the near field is approximated using EQ3/6 in terms of limiting conditions at equilibrium, or steady state, in three closed systems representing fully saturated bentonite, Fe o corrosion products of the canister, and spent fuel. The calculations consider both low-temperature (15 deg C) and high-temperature (80 deg C) conditions in the near field, and the existence of either reducing or strongly oxidizing conditions in each of the bentonite, canister, and spent-fuel barriers. Heterogeneities in site characteristics are evaluated through consideration of a range of initial groundwaters and their interactions with engineered barriers. Aqueous speciation models for many radioelements are constrained by thermodynamic data that are estimated with varying degrees of accuracy. An important question, however, is how accurate do these models need to be for purposes of estimating source-term concentrations? For example, it is unrealistic to expect a high degree of accuracy in speciation models if such models predict solubilities that are below the analytical detection limit for a given radioelement. From a practical standpoint, such models are irrelevant if calculated solubilities cannot be tested by direct comparison to experimental data. In the absence of models that are both accurate and relevant for conditions of interest, the detection limit could define a pragmatic upper limit on radioelement solubility

Prevention of Acid Mine Drainage Through Complexation of Ferric Iron by Soluble Microbial Growth Products

Science.gov (United States)

Pandey, S.; Yacob, T. W.; Silverstein, J.; Rajaram, H.; Minchow, K.; Basta, J.

2011-12-01

Acid mine drainage (AMD) is a widespread environmental problem with deleterious impacts on water quality in streams and watersheds. AMD is generated largely by the oxidation of metal sulfides (i.e. pyrite) by ferric iron. This abiotic reaction is catalyzed by conversion of ferrous to ferric iron by iron and sulfur oxidizing microorganisms. Biostimulation is currently being investigated as an attempt to inhibit the oxidation of pyrite and growth of iron oxidizing bacteria through addition of organic carbon. This may stimulate growth of indigenous communities of acidophilic heterotrophic bacteria to compete for oxygen. The goal of this research is to investigate a secondary mechanism associated with carbon addition: complexation of free Fe(III) by soluble microbial growth products (SMPs) produced by microorganisms growing in waste rock. Exploratory research at the laboratory scale examined the effect of soluble microbial products (SMPs) on the kinetics of oxidation of pure pyrite during shaker flask experiments. The results confirmed a decrease in the rate of pyrite oxidation that was dependent upon the concentration of SMPs in solution. We are using these data to verify results from a pyrite oxidation model that accounts for SMPs. This reactor model involves differential-algebraic equations incorporating total component mass balances and mass action laws for equilibrium reactions. Species concentrations determined in each time step are applied to abiotic pyrite oxidation rate expressions from the literature to determine the evolution of total component concentrations. The model was embedded in a parameter estimation algorithm to determine the reactive surface area of pyrite in an abiotic control experiment, yielding an optimized value of 0.0037 m2. The optimized model exhibited similar behavior to the experiment for this case; the root mean squared of residuals for Fe(III) was calculated to be 7.58 x 10-4 M, which is several orders of magnitude less than the actual

Refinement of Modeled Aqueous-Phase Sulfate Production via the Fe- and Mn-Catalyzed Oxidation Pathway

Directory of Open Access Journals (Sweden)

Syuichi Itahashi

2018-04-01

Full Text Available We refined the aqueous-phase sulfate (SO42− production in the state-of-the-art Community Multiscale Air Quality (CMAQ model during the Japanese model inter-comparison project, known as Japan’s Study for Reference Air Quality Modeling (J-STREAM. In Japan, SO42− is the major component of PM2.5, and CMAQ reproduces the observed seasonal variation of SO42− with the summer maxima and winter minima. However, CMAQ underestimates the concentration during winter over Japan. Based on a review of the current modeling system, we identified a possible reason as being the inadequate aqueous-phase SO42− production by Fe- and Mn-catalyzed O2 oxidation. This is because these trace metals are not properly included in the Asian emission inventories. Fe and Mn observations over Japan showed that the model concentrations based on the latest Japanese emission inventory were substantially underestimated. Thus, we conducted sensitivity simulations where the modeled Fe and Mn concentrations were adjusted to the observed levels, the Fe and Mn solubilities were increased, and the oxidation rate constant was revised. Adjusting the concentration increased the SO42− concentration during winter, as did increasing the solubilities and revising the rate constant to consider pH dependencies. Statistical analysis showed that these sensitivity simulations improved model performance. The approach adopted in this study can partly improve model performance in terms of the underestimation of SO42− concentration during winter. From our findings, we demonstrated the importance of developing and evaluating trace metal emission inventories in Asia.

An experimental study on MRI signal intensity vs concentration of water-soluble contrast media

International Nuclear Information System (INIS)

Lee, Ghi Jai; Han, Chang Yul; Chang, Kee Hyun; Han, Moon Hee; Han, Man Chung

1991-01-01

There has been only one report that water-soluble contrast media containing iodine and used in conventional X -ray radiography reduce T1-and T2-relaxation times. We evaluated the relationship between signal intensity (relative signal intensity to normal saline) and T2-relaxation time of MRI and the concentration of 3 water-soluble contrast media [meglumine ioxithalamate (Telebrix 30), iopromide (Ultravist 300), iotrolan (Isovist 300)] through the phantom study, using both 2.0T and 0.5T MR units. We found that the signal intensity increased significantly on the T1-weighted images as the concentration of contrast media increased. The degree of the increase was larger on 0.5T MR than on 2.0T MR. The signal intensity on proton density image showed no significant difference at various concentrations. However, there were significant decreases of both signal intensity on the T2-weighted images and T2-relaxation time as the concentration of contrast media increased, which was more prominent on 2.0T MR than 0.5T MR. Between the contrast media of the same concentration, there was no significant difference in signal intensity and T2-relaxation time

Importance of critical micellar concentration for the prediction of solubility enhancement in biorelevant media.

Science.gov (United States)

Ottaviani, G; Wendelspiess, S; Alvarez-Sánchez, R

2015-04-06

This study evaluated if the intrinsic surface properties of compounds are related to the solubility enhancement (SE) typically observed in biorelevant media like fasted state simulated intestinal fluids (FaSSIF). The solubility of 51 chemically diverse compounds was measured in FaSSIF and in phosphate buffer and the surface activity parameters were determined. This study showed that the compound critical micellar concentration parameter (CMC) correlates strongly with the solubility enhancement (SE) observed in FaSSIF compared to phosphate buffer. Thus, the intrinsic capacity of molecules to form micelles is also a determinant for each compound's affinity to the micelles of biorelevant surfactants. CMC correlated better with SE than lipophilicity (logD), especially over the logD range typically covered by drugs (2 < logD < 4). CMC can become useful to guide drug discovery scientists to better diagnose, improve, and predict solubility in biorelevant media, thereby enhancing oral bioavailability of drug candidates.

Feasibility of closed Fe(II)/Fe(III) system for product-reflux in Nitrox process

International Nuclear Information System (INIS)

Adachi, M.; Ishida, T.

1981-01-01

A concept of closed reflux system for stable isotope fractionation by chemical exchange method has been introduced. In a closed system a chemical agent used to convert one chemical species of an isotopic exchange reaction into the other at the product end is regenerated on site by means of an electrochemical or thermal process. It offers a convenience of eliminating the needs for transporting chemicals to and from the site and an advantage of allowing leniency in the degree of completeness of the reflux reaction. Feasibility of use of Fe(II) salt solutions in a closed reflux system for the Nitrox process for 15 N fractionation has been studied. Two of such systems, FeSO 4 in H 2 SO 4 and Fe(ClO 4 ) 2 in HClO 4 , are adopted for packed column operation. For both systems, the rate of reduction of nitric acid increases with increasing acid concentration, the solubility of the salts decreases with the increasing acid concentration, and the reflux reaction can be made to go to completion. Evaluation of such a closed reflux system will have to include that of performance of regenerative process

Carbothermic reduction behaviors of Ti-Nb-bearing Fe concentrate from Bayan Obo ore in China

Science.gov (United States)

Wang, Guang; Du, Ya-xing; Wang, Jing-song; Xue, Qing-guo

2018-01-01

To support the development of technology to utilize low-grade Ti-Nb-bearing Fe concentrate, the reduction of the concentrate by coal was systematically investigated in the present paper. A liquid phase formed when the Ti-Nb-bearing Fe concentrate/coal composite pellet was reduced at temperatures greater than 1100°C. The addition of CaCO3 improved the reduction rate when the slag basicity was less than 1.0 and inhibited the formation of the liquid phase. Mechanical milling obviously increased the metallization degree compared with that of the standard pellet when reduced under the same conditions. Evolution of the mineral phase composition and microstructure of the reduced Ti-Nb-bearing Fe concentrate/coal composite pellet at 1100°C were analyzed by X-ray diffraction and scanning electron microscopy-energy-dispersive spectroscopy. The volume shrinkage value of the reduced Ti-Nb-bearing Fe concentrate/coal composite pellet with a basicity of 1.0 was approximately 35.2% when the pellet was reduced at 1100°C for 20 min, which enhanced the external heat transfer to the lower layers when reduced in a practical rotary hearth furnace. The present work provides key parameters and mechanism understanding for the development of carbothermic reduction technology of a Ti-Nb-bearing Fe concentrate incorporated in a pyrometallurgical utilization flow sheet.

Hydrogen solubility in iron, platinum and their alloys under pressure up to 67 kbars

International Nuclear Information System (INIS)

Belash, I.T.; Antonov, V.E.; Ponyatovskij, E.G.

1979-01-01

The solubility of hydrogen was studied in iron, nickel and Fe-Pt-H alloy at a high pressure. It was shown that at T=250 deg C and psub(Hsub(2))=67 kbar, the solubility hy of hydrogen in α-iron and platinum is below the sensitivity threshold of the employed method of chemical analysis, deltasub(n) approximately 0.05 (n - atomic ratio hydrogen metal). At this pressure and at a temperature of T=150 deg C, the equilibrium concentration of hydrogen in non-ordered Fe-Pt alloys with a FCC lattice, containing 25 and 32 at. % Pt, attains, respectively, n = (5+-2)x10 -2 and (2+-5)x10 -2 . Ordering of the alloy with 25 at. % Pt produces no substantial change in the solubility of hydrogen. In a hydrogen atmosphere, the dependence of the Curie point Tsub(c)(psub(Hsub(2)) deviates from Tsub(c)(p). In an inert medium, at p=67 kbar, ΔTsub(c)=Tsub(c)(psub(Hsub(2)) - Tsub(c)(p) = 35+-10 deg C

Irradiation-induced patterning in dilute Cu–Fe alloys

International Nuclear Information System (INIS)

Stumphy, B.; Chee, S.W.; Vo, N.Q.; Averback, R.S.; Bellon, P.; Ghafari, M.

2014-01-01

Compositional patterning in dilute Cu 1−x Fe x (x ≈ 12%) induced by 1.8 MeV Kr + irradiation was studied as a function of temperature using atom probe tomography. Irradiation near room temperature led to homogenization of the sample, whereas irradiation at 300 °C and above led to precipitation and macroscopic coarsening. Between these two temperatures the irradiated alloys formed steady state patterns of composition where precipitates grew to a fixed size. The size in this regime increased somewhat with temperature. It was also observed that the steady state concentrations of Fe in Cu matrix and Cu in the Fe precipitates both greatly exceeded their equilibrium solubilities, with the degree of supersaturation in each phase decreasing with increasing temperature. In the macroscopic coarsening regime, the Fe-rich precipitates showed indications of a “cherry-pit” structure, with Cu precipitates forming within the Fe precipitates. In the patterning regime, interfaces between Fe-rich precipitates and the Cu-rich matrix were irregular and diffuse

Effect of foliar applied (Zn, Fe, Cu and Mn) in citrus production

International Nuclear Information System (INIS)

Khurshid, F.; Sarwar, S.; Khattak, R.A.

2008-01-01

A study was conducted to evaluate the impact of micronutrients (Zn, Fe, Cu and Mn) on sweet orange (Citrus Sinensis L.), blood red var., on farmer's orchard at Khanpur, district Haripur, NWFP, during 2002-03. Micronutrients were applied in foliar sprays over the canopy of each tree. The main effects and interactions of Zinc sulphate (Zn), iron sulphate (Fe), Copper Sulphate (Cu) and Manganese Sulphate (Mn) were studied in factorial combinations. A basal dose of nitrogen, phosphorus and potassium was applied at the rate 1.5, 1 and 1 kg tree/sup -1/. Zn, Fe, Cu and Mn were applied alone and in various combinations at the rate 0.115, 0.057, 0.05 and 0.13 kg in 100 liters of water. Application of micronutrients significantly increased Zn, Fe, Cu and Mn concentrations in leaves, compared with control. Zn treatments significantly increased the yield, number of fruit and total sugar. Manganese treatments significantly increased the total soluble solids and reduced the acidity of fruit juice. Other quality parameters, including fruit size, percent peel, percent pulp, sugar as well as total soluble solids, were improved with the application of Zn, Fe, Cu and Mn. (author)

The initial oxidation of e-Fe2N1-x: an XPS investigation

DEFF Research Database (Denmark)

Graat, Peter C.J.; Somers, Marcel A. J.; Mittemeijer, Eric J.

1998-01-01

. Analysis of the N Is spectra provided information on the electric charge on nitrogen atoms and the depth distribution of nitrogen. A linear relation was found between the N Is electron binding energy and the nitrogen concentration in the substrate. Upon oxidation of the iron nitride, nitrogen atoms...... accumulated underneath the oxide film. If the nitrogen concentration at that location exceeded the maximum solubility of nitrogen in epsilon-Fe2N1-x an additional N peak appeared in the N Is spectrum, which indicated the formation of a nitrogen containing phase other than epsilon-Fe2N1-x at the nitride...

Solubility and release of fenbufen intercalated in Mg, Al and Mg, Al, Fe layered double hydroxides (LDH): The effect of Eudragit S 100 covering

International Nuclear Information System (INIS)

Arco, M. del; Fernandez, A.; Martin, C.; Rives, V.

2010-01-01

Following different preparation routes, fenbufen has been intercalated in the interlayer space of layered double hydroxides with Mg 2+ and Al 3+ or Mg 2+ , Al 3+ and Fe 3+ in the layers. Well crystallized samples were obtained in most of the cases (intercalation was not observed by reconstruction of the MgAlFe matrix), with layer heights ranging between 16.1 and 18.8 A. The presence of the LDH increases the solubility of fenbufen, especially when used as a matrix. The dissolution rate of the drug decreases when the drug is intercalated, and is even lower in those systems containing iron; release takes place through ionic exchange with phosphate anions from the solution. Preparation of microspheres with Eudragit S 100 leads to solids with an homogeneous, smooth surface with efficient covering of the LDH surface, as drug release was not observed at pH lower than 7. - Graphical abstract: LDHs containing Mg, Al, Fe increase fenbufen solubility, release takes place through ionic exchange with phosphate anions from the medium. Spherical solids with homogeneous, smooth surface are formed when using Eudragit S 100, efficiently covering the LDH surface. Display Omitted

Solubility of magnetite in coolant of NPP boiling reactor

International Nuclear Information System (INIS)

Zarembo, V.I.; Kritskij, V.G.; Slobodov, A.A.; Puchkov, L.V.

1988-01-01

To improve water-chemical NPP regimes calculations of iron solubility up to 600 K temperature in Fe 3 O 4 -H 2 O-O 2 and Fe(OH) 3 -H 2 O systems are performed using a system of selected and consistent values of thermal constants of various chemical iron forms in standard aqueous solution state. Calculations have shown that up to 423 K in aqueous medium containing oxygen, magnetite is unstable and is oxidized first up to Fe(OH) 3 and then - up to Fe OOH and Fe 2 O 3 . Calculations complying with experimental data have demonstrated the presence of maximum on the curve solubility-temperature in desalinized water containing 10 μkg/kg of oxygen. A sequence of processes of oxygen effect on water regime and corrosion prduct deposition in a condensate-feed circuit of NPP boiling reactor is proposed. It is proved that under oxygen water chemistry of condensate-feed circuit after magnetite transfomation into gematite, reduction of soluble iron form inlet to reactor loop occurs, which allows one to expect reduction of γ-radiation dose rate buildup around the primary loop pipelines

Consumption of a dietary portfolio of cholesterol lowering foods improves blood lipids without affecting concentrations of fat soluble compounds.

Science.gov (United States)

Ramprasath, Vanu R; Jenkins, David J A; Lamarche, Benoit; Kendall, Cyril W C; Faulkner, Dorothea; Cermakova, Luba; Couture, Patrick; Ireland, Chris; Abdulnour, Shahad; Patel, Darshna; Bashyam, Balachandran; Srichaikul, Korbua; de Souza, Russell J; Vidgen, Edward; Josse, Robert G; Leiter, Lawrence A; Connelly, Philip W; Frohlich, Jiri; Jones, Peter J H

2014-10-18

Consumption of a cholesterol lowering dietary portfolio including plant sterols (PS), viscous fibre, soy proteins and nuts for 6 months improves blood lipid profile. Plant sterols reduce blood cholesterol by inhibiting intestinal cholesterol absorption and concerns have been raised whether PS consumption reduces fat soluble vitamin absorption. The objective was to determine effects of consumption of a cholesterol lowering dietary portfolio on circulating concentrations of PS and fat soluble vitamins. Using a parallel design study, 351 hyperlipidemic participants from 4 centres across Canada were randomized to 1 of 3 groups. Participants followed dietary advice with control or portfolio diet. Participants on routine and intensive portfolio involved 2 and 7 clinic visits, respectively, over 6 months. No changes in plasma concentrations of α and γ tocopherol, lutein, lycopene and retinol, but decreased β-carotene concentrations were observed with intensive (week 12: p = 0.045; week 24: p = 0.039) and routine (week 12: p = 0.031; week 24: p = 0.078) portfolio groups compared to control. However, cholesterol adjusted β-carotene and fat soluble compound concentrations were not different compared to control. Plasma PS concentrations were increased with intensive (campesterol:p = 0.012; β-sitosterol:p = 0.035) and routine (campesterol: p = 0.034; β-sitosterol: p = 0.080) portfolio groups compared to control. Plasma cholesterol-adjusted campesterol and β-sitosterol concentrations were negatively correlated (p portfolio diet reduces serum total and LDL-C levels while increasing PS values, without altering fat soluble compounds concentrations. The extent of increments of PS with the current study are not deleterious and also maintaining optimum levels of fat soluble vitamins are of paramount necessity to maintain overall metabolism and health. Results indicate portfolio diet as one of the best options for CVD risk reduction

Melting relations in the Fe-rich portion of the system FeFeS at 30 kb pressure

Science.gov (United States)

Brett, R.; Bell, P.M.

1969-01-01

The melting relations of FeFeS mixtures covering the composition range from Fe to Fe67S33 have been determined at 30 kb pressure. The phase relations are similar to those at low pressure. The eutectic has a composition of Fe72.9S27.1 and a temperature of 990??C. Solubility of S in Fe at elevated temperatures at 30 kb is of the same order of magnitude as at low pressure. Sulfur may have significantly lowered the melting point of iron in the upper mantle during the period of coalescence of metal prior to core formation in the primitive earth. ?? 1969.

Solubility Products of M(II) - Carbonates

International Nuclear Information System (INIS)

Grauer, Rolf; Berner, Urs

1999-01-01

Many solubility data for M(II) carbonates commonly compiled in tables are contradictory and sometimes obviously wrong. The quality of such data has been evaluated based on the original publications and reliable solubility constants have been selected for the carbonates of Mn, Fe, Co, Ni, Cu, Zn, Cd and Pb with the help of cross-comparisons. (author)

Solubility of hydrogen in delta iron

International Nuclear Information System (INIS)

Shapovalov, V.I.; Trofimenko, V.V.

1979-01-01

The solubility of hydrogen in iron (less than 0.002 % impurities) at temperatures of 800-1510 deg C and a pressure of 100 atm was measured. The heat of solution of hydrogen in delta-Fe, equal to 73 kJ/g-atom, is by far greater than the corresponding values for α- and γ-Fe

Atmospheric Processing of Volcanic Glass: Effects on Iron Solubility and Redox Speciation.

Science.gov (United States)

Maters, Elena C; Delmelle, Pierre; Bonneville, Steeve

2016-05-17

Volcanic ash from explosive eruptions can provide iron (Fe) to oceanic regions where this micronutrient limits primary production. Controls on the soluble Fe fraction in ash remain poorly understood but Fe solubility is likely influenced during atmospheric transport by condensation-evaporation cycles which induce large pH fluctuations. Using glass powder as surrogate for ash, we experimentally simulate its atmospheric processing via cycles of pH 2 and 5 exposure. Glass fractional Fe solubility (maximum 0.4%) is governed by the pH 2 exposure duration rather than by the pH fluctuations, however; pH 5 exposure induces precipitation of Fe-bearing nanoparticles which (re)dissolve at pH 2. Glass leaching/dissolution release Fe(II) and Fe(III) which are differentially affected by changes in pH; the average dissolved Fe(II)/Fetot ratio is ∼0.09 at pH 2 versus ∼0.18 at pH 5. Iron release at pH 2 from glass with a relatively high bulk Fe(II)/Fetot ratio (0.5), limited aqueous Fe(II) oxidation at pH 5, and possibly glass-mediated aqueous Fe(III) reduction may render atmospherically processed ash a significant source of Fe(II) for phytoplankton. By providing new insight into the form(s) of Fe associated with ash as wet aerosol versus cloud droplet, we improve knowledge of atmospheric controls on volcanogenic Fe delivery to the ocean.

The Effect of Fe Concentration on the Quality and Quantity of Biogas Produced From Fermentation of Palm Oil Mill Effluent

Directory of Open Access Journals (Sweden)

Irvan Matseh

2012-10-01

Full Text Available The purpose of this research is to study the effect of Fe concentration as a trace metal on the quality and quantity of biogas produced from the fermentation of palm oil mill effluent (POME. Raw POME as feed was obtained from one of the palm oil mills belong to PTPN IV, other materials used were hydrochloric acid, sodium bicarbonate, and trace metals. Observed variables were volume of biogas, concentration of Fe in raw POME and biodigester, degradation rate of total solid (TS and volatile solid (VS, M-Alkalinity, pH, H2S and CO2 concentration in biogas at hydraulic retention time (HRT 6 days. Before HRT of 6 days reached, initial trace metal compositions were 25.2 mg/L of Fe, 0.42 mg/L of Co, and 0.49 mg/L of Ni. After that, composition of trace metal were consisted only Co and Ni. The results showed that Fe as a trace metal did not affect the production or quantity of biogas. When Fe concentration reached over to 330 mg/L then concentration of CH4, total solid (TS and volatile solid (VS decreased. Moreover, the higher the Fe contents the smaller of H2S production. Fe content in POME from the same mill had different concentration, as the consequence biogas with different H2S concentrations were produced as well. Thus, Fe in the trace metals is no longer required if high concentration of Fe already existed in POME because it can reduce the formation of H2S. In addition, too high concentration of Fe in POME can be toxic for microorganism in the fermentation of biogas.

Predicting trace metal solubility and fractionation in Urban soils from isotopic exchangeability

International Nuclear Information System (INIS)

Mao, L.C.; Young, S.D.; Tye, A.M.; Bailey, E.H.

2017-01-01

Metal-salt amended soils (MA, n = 23), and historically-contaminated urban soils from two English cities (Urban, n = 50), were investigated to assess the effects of soil properties and contaminant source on metal lability and solubility. A stable isotope dilution method, with and without a resin purification step, was used to measure the lability of Cd, Cu, Ni, Pb and Zn. For all five metals in MA soils, lability (%E-values) could be reasonably well predicted from soil pH value with a simple logistic equation. However, there was evidence of continuing time-dependent fixation of Cd and Zn in the MA soils, following more than a decade of storage under air-dried conditions, mainly in high pH soils. All five metals in MA soils remained much more labile than in Urban soils, strongly indicating an effect of contaminant source on metal lability in the latter. Metal solubility was predicted for both sets of soil by the geochemical speciation model WHAM-VII, using E-value as an input variable. For soils with low metal solution concentrations, over-estimation of Cd, Ni and Zn solubility was associated with binding to the Fe oxide fraction while accurate prediction of Cu solubility was dependent on humic acid content. Lead solubility was most poorly described, especially in the Urban soils. Generally, slightly poorer estimation of metal solubility was observed in Urban soils, possibly due to a greater incidence of high pH values. The use of isotopically exchangeable metal to predict solubility is appropriate both for historically contaminated soils and where amendment with soluble forms of metal is used, as in toxicological trials. However, the major limitation to predicting solubility may lie with the accuracy of model input variables such as humic acid and Fe oxide contents where there is often a reliance on relatively crude analytical estimations of these variables. Trace metal reactivity in urban soils depends on both soil properties and the original source material

Solubilities of some hydrous REE phosphates with implications for diagenesis and sea water concentrations

International Nuclear Information System (INIS)

Jonasson, R.G.; Bancroft, G.M.; Nesbitt, H.W.

1985-01-01

Solubility product determinations suggest that the hydrous phosphates of the rare earths, REPO 4 .xH 2 O, are important in controlling the sea water REE concentrations. Two of these solids, rhabdophane, (P6 2 22) and 'hydrous xenotime', (I4 1 /amd), have been synthesized at 100 C via the acid hydrolysis of the respective REE pyrophosphate. The solubility products at infinite dilution were determined to be pK 0 = 24.5, (La at 25 C); 26.0, (Pr at 100 C); 25.7, (Nd at 100 C); and 25.5, (Er at 100 C). On the basis of calculations involving the reaction of Re 3+ with apatite to form the hydrous phosphate, the lanthanum concentration in sea water is predicted to be about 140 pmol/L. Laboratory experiments support the hypothesis that apatite is a substrate for reactions with dissolved REE. (author)

The effect of change in pH on the solubility of iron bis-glycinate chelate and other iron compounds.

Science.gov (United States)

García-Casal, M N; Layrisse, M

2001-03-01

The effect of a pH change from 2 to 6 was tested on the solubility of ferrous sulfate, ferrous fumarate, iron bis-glycine chelate (Ferrochel) and sodium-iron ethylenediaminetetraacetic acid (NaFeEDTA). It was found that at pH 2 ferrous sulfate, Ferrochel and NaFeEDTA were completely soluble and only 75% of iron from ferrous fumarate was soluble. When pH was raised to 6, iron from amino acid chelate and NaFeEDTA remained completely soluble while solubility from ferrous sulfate and ferrous fumarate decreased 64 and 74%, respectively compared to the amount of iron initially soluble at pH 2. These results suggest that iron solubility from iron bis-glycine chelate and NaFeEDTA is not affected by pH changes within the ranges tested, probably because iron remained associated to the respective compounds.

Iron and zinc concentrations and 59Fe retention in developing fetuses of zinc-deficient rats

International Nuclear Information System (INIS)

Rogers, J.M.; Loennerdal, B.H.; Hurley, L.S.; Keen, C.L.

1987-01-01

Because disturbances in iron metabolism might contribute to the teratogenicity of zinc deficiency, we examined the effect of zinc deficiency on fetal iron accumulation and maternal and fetal retention of 59 Fe. Pregnant rats were fed from mating a purified diet containing 0.5, 4.5 or 100 micrograms Zn/g. Laparotomies were performed on d 12, 16, 19 and 21 of gestation. Maternal blood and concepti were analyzed for zinc and iron. Additional groups of dams fed 0.5 or 100 micrograms Zn/g diet were gavaged on d 19 with a diet containing 59 Fe. Six hours later maternal blood and tissues, fetuses and placentas were counted for 59 Fe. Maternal plasma zinc, but not iron, concentration was affected by zinc deficiency on d 12. Embryo zinc concentration on d 12 increased with increasing maternal dietary zinc, whereas iron concentration was not different among groups. On d 16-21 plasma iron was higher in dams fed 0.5 micrograms Zn/g diet than in those fed 4.5 or 100 micrograms/g, whereas plasma zinc was lower in dams fed 0.5 or 4.5 micrograms Zn/g than in those fed 100 micrograms Zn/g diet. On d 19 zinc concentration in fetuses from dams fed 0.5 micrograms/g zinc was not different from that of those fed 4.5 micrograms/g zinc, and iron concentration was higher in the 0.5 microgram Zn/g diet group. The increase in iron concentration in zinc-deficient fetuses thus occurs too late to be involved in major structural teratogenesis. Although whole blood concentration of 59 Fe was not different in zinc-deficient and control dams, zinc-deficient dams had more 59 Fe in the plasma fraction

Mechanisms for Fe(III) oxide reduction in sedimentary environments

Science.gov (United States)

Nevin, Kelly P.; Lovely, Derek R.

2002-01-01

Although it was previously considered that Fe(III)-reducing microorganisms must come into direct contact with Fe(III) oxides in order to reduce them, recent studies have suggested that electron-shuttling compounds and/or Fe(III) chelators, either naturally present or produced by the Fe(III)-reducing microorganisms themselves, may alleviate the need for the Fe(III) reducers to establish direct contact with Fe(III) oxides. Studies with Shewanella alga strain BrY and Fe(III) oxides sequestered within microporous beads demonstrated for the first time that this organism releases a compound(s) that permits electron transfer to Fe(III) oxides which the organism cannot directly contact. Furthermore, as much as 450 w M dissolved Fe(III) was detected in cultures of S. alga growing in Fe(III) oxide medium, suggesting that this organism releases compounds that can solublize Fe(III) from Fe(III) oxide. These results contrast with previous studies, which demonstrated that Geobacter metallireducens does not produce electron-shuttles or Fe(III) chelators. Some freshwater aquatic sediments and groundwaters contained compounds, which could act as electron shuttles by accepting electrons from G. metallireducens and then transferring the electrons to Fe(III). However, other samples lacked significant electron-shuttling capacity. Spectroscopic studies indicated that the electron-shuttling capacity of the waters was not only associated with the presence of humic substances, but water extracts of walnut, oak, and maple leaves contained electron-shuttling compounds did not appear to be humic substances. Porewater from a freshwater aquatic sediment and groundwater from a petroleum-contaminated aquifer contained dissolved Fe(III) (4-16 w M), suggesting that soluble Fe(III) may be available as an electron acceptor in some sedimentary environments. These results demonstrate that in order to accurately model the mechanisms for Fe(III) reduction in sedimentary environments it will be necessary

Preparation and characterization of highly water-soluble magnetic Fe{sub 3}O{sub 4} nanoparticles via surface double-layered self-assembly method of sodium alpha-olefin sulfonate

Energy Technology Data Exchange (ETDEWEB)

Li, Honghong; Qin, Li [School of Chemistry and Chemical Engineering, University of Jinan, Jinan 250022 (China); Feng, Ying [Department of Bridge Engineering, Shanxi Railway Institute, Weinan 714000 (China); Hu, Lihua [School of Chemistry and Chemical Engineering, University of Jinan, Jinan 250022 (China); Zhou, Chunhua, E-mail: chm_zhouch@ujn.edu.cn [School of Chemistry and Chemical Engineering, University of Jinan, Jinan 250022 (China)

2015-06-15

A kind of double-layered self-assembly sodium alpha-olefin sulfonate (AOS) capped Fe{sub 3}O{sub 4} magnetic nanoparticles (Fe{sub 3}O{sub 4}-AOS-MN) with highly water-solubility was prepared by a wet co-precipitation method with a pH of 4.8. The resulting Fe{sub 3}O{sub 4}-AOS-MN could be dispersed into water to form stable magnetic fluid without other treatments. The result of X-ray diffraction (XRD) indicated that the Fe{sub 3}O{sub 4}-AOS-MN maintained original crystalline structure and exhibited a diameter of about 7.5 nm. The iron oxide phase of nanoparticles determined by Raman spectroscopy is Fe{sub 3}O{sub 4}. Transmission electron microscopy (TEM) analysis confirmed that the Fe{sub 3}O{sub 4}-AOS-MN with spherical morphology were uniformly dispersed in water. FT-IR spectroscopy (FT-IR) and thermo-gravimetric analysis (TGA) verified the successful preparation of Fe{sub 3}O{sub 4}-AOS-MN capped with double-layered self-assembled AOS. The corresponding capacities of monolayer chemical absorption and the second-layer self-assembly absorption were respectively 4.07 and 14.71 wt% of Fe{sub 3}O{sub 4}-MN, which were much lower than those of other surfactants. Vibrating sample magnetometer (VSM) test result showed Fe{sub 3}O{sub 4}-AOS-MN possessed superparamagnetic behavior with the saturation magnetization value of about 44.45 emu/g. The blocking temperature T{sub B} of Fe{sub 3}O{sub 4}-AOS-MN capped with double-layered AOS is 170 K. - Highlights: • Double-layered self-assembly sodium alpha-olefin sulfonate (AOS) capped Fe{sub 3}O{sub 4} magnetic nanoparticles are prepared by a wet co-precipitation method. • Double-layered Fe{sub 3}O{sub 4}-AOS-MN exhibits highly water-solubility. • The iron oxide phase is determined by Raman spectroscopy. • Fe{sub 3}O{sub 4}-AOS-MN capped with double-layered AOS possesses super-paramagnetic behavior. • The blocking temperature T{sub B} of Fe{sub 3}O{sub 4}-AOS-MN capped with double-layered AOS is 170 K.

Assessing the solubility controls on vanadium in groundwater, northeastern San Joaquin Valley, CA

Science.gov (United States)

Wright, Michael T.; Stollenwerk, Kenneth G.; Belitz, Kenneth

2014-01-01

The solubility controls on vanadium (V) in groundwater were studied due to concerns over possible harmful health effects of ingesting V in drinking water. Vanadium concentrations in the northeastern San Joaquin Valley ranged from 25 μg/L) and lowest in samples collected from anoxic groundwater (70% 2VO4−. Adsorption/desorption reactions with mineral surfaces and associated oxide coatings were indicated as the primary solubility control of V5+ oxyanions in groundwater. Environmental data showed that V concentrations in oxic groundwater generally increased with increasing groundwater pH. However, data from adsorption isotherm experiments indicated that small variations in pH (7.4–8.2) were not likely as an important a factor as the inherent adsorption capacity of oxide assemblages coating the surface of mineral grains. In suboxic groundwater, accurate SM modeling was difficult since Eh measurements of source water were not measured in this study. Vanadium concentrations in suboxic groundwater decreased with increasing pH indicating that V may exist as an oxycationic species [e.g. V(OH)3+]. Vanadium may complex with dissolved inorganic and organic ligands under suboxic conditions, which could alter the adsorption behavior of V in groundwater. Speciation modeling did not predict the existence of V-inorganic ligand complexes and organic ligands were not collected as part of this study. More work is needed to determine processes governing V solubility under suboxic groundwater conditions. Under anoxic groundwater conditions, SM predicts that aqueous V exists as the uncharged V(OH)3 molecule. However, exceedingly low V concentrations show that V is sparingly soluble in anoxic conditions. Results indicated that V may be precipitating as V3+- or mixed V3+/Fe3+-oxides in anoxic groundwater, which is consistent with results of a previous study. The fact that V appears insoluble in anoxic (Fe reducing) redox conditions indicates that the behavior of V is different than

Review and recommended thermodynamic properties of FeCO3

DEFF Research Database (Denmark)

Fosbøl, Philip Loldrup; Thomsen, Kaj; Stenby, Erling Halfdan

2010-01-01

An extensive review of entropy, enthalpy of formation and Gibbs energy of formation, heat capacity, aqueous solubility and solubility constant of FeCO3 is given. A consistent set of thermodynamic properties for FeCO3 and relevant aqeous species is selected and recommended for use. Speciation...

Phase equilibrium of the Gd-Fe-Co system at 873 K

International Nuclear Information System (INIS)

Huang Jinli; Zhong Haichang; Xia Xiuwen; He Wei; Zhu Jinming; Deng Jianqiu; Zhuang Yinghong

2009-01-01

Phase equilibrium of the ternary Gd-Fe-Co system at 873 K was investigated by using X-ray diffraction technique, electron probe microanalysis, metallographic analysis and differential thermal analysis. The 873 K isothermal section of the phase diagram of the Gd-Fe-Co ternary system consists of 11 single-phase regions, 16 two-phase regions and 6 three-phase regions. Three pairs of corresponding compounds of Gd-Co and Gd-Fe, i.e., Gd 2 Co 17 and Gd 2 Fe 17 , GdCo 3 and GdFe 3 , GdCo 2 and GdFe 2 , form a continuous series of solid solution. The compound Gd 2 Co 7-x Fe x was found to have a broad solubility range from 0 to 31 at.% Fe. The maximum solubility of Co in Gd 6 Fe 23 is about 7 at.% Co. At 873 K, the maximum solubilities of Fe in Gd 3 Co and Gd 4 Co 3 are about 3 and 1 at.% Fe, respectively. No ternary compound was found in all ternary alloy samples

Effect of chloride concentration on the solubility of amorphous uranium dioxide at 25deg C under reducing conditions

International Nuclear Information System (INIS)

Aguilar, M.; Casas, I.; Pablo, J. de; Torrero, M.E.

1991-01-01

The dependence of the solubility of a microcrystalline uranium dioxide on the chloride concentration has been studied at 25deg C under reducing conditions. The concentration of uranium in solution has been found to be some orders of magnitude lower than in perchlorate media. Possible changes of both the morphology and the composition of the solid phase have been investigated by means of Energy Dispersive X-ray Analysis (EDX) and X-ray Powder Difraction (XPD). The formation of a secondary solid phase as a reason for the decrease of the solubility has been postulated. (orig.)

Synthesis of highly reactive polyisobutylene with FeCl3/ether complexes in hexane; kinetic and mechanistic studies

KAUST Repository

Kumar, Rajeev Ananda; De, Priyadarsi; Zheng, Bin; Huang, Kuo-Wei; Emert, Jack I.; Faust, Rudolf

2015-01-01

The kinetics and mechanism of the polymerization of isobutylene catalyzed by FeCl3·ether complexes in hexane at 0°C were investigated. The polymerization rates increased in the diisopropyl ether< 2-chloroethyl ethyl ether < bis(2-chloroethyl) ether order, attributed to electronic effects. The polymerization rates increased with increasing initiator and catalyst concentrations. The first order plots, however, deviated from the linear suggesting that the cation concentration decreases with time. The previously proposed mechanism is inadequate to explain this finding. The decrease in the polymerization rate with time is explained by the low solubility of the H+ROR′FeCl4 - complexes that precipitate during polymerization. Based on mechanistic studies the revised mechanism now also includes the equilibrium H+ROR′FeCl4 - ⇋ HCl + FeCl3·ROR′.

Equilibrium solubility of CO{sub 2} in aqueous solutions of 1-amino-2-propanol as function of concentration, temperature, and pressure

Energy Technology Data Exchange (ETDEWEB)

Rebolledo-Morales, Miguel Angel; Rebolledo-Libreros, Maria Esther [Instituto Mexicano del Petroleo, Direccion de Investigacion y Posgrado, Programa de Ingenieria Molecular, Area de Investigacion de Termofisica, Eje Central Lazaro Cardenas Norte 152, 07730 Mexico, D.F. (Mexico); Trejo, Arturo, E-mail: atrejo@imp.m [Instituto Mexicano del Petroleo, Direccion de Investigacion y Posgrado, Programa de Ingenieria Molecular, Area de Investigacion de Termofisica, Eje Central Lazaro Cardenas Norte 152, 07730 Mexico, D.F. (Mexico)

2011-05-15

Research highlights: Gas solubility of CO{sub 2} in aqueous solutions of 1-amino-2-propanol was measured. Solubility increases as pressure and concentration of 1-amino-2-propanol increase. The Kent-Eisenberg model was used to correlate all the experimental results. Aqueous solutions of MIPA are an excellent alternative to use in gas purification. - Abstract: Using a dynamic method with recirculation of the vapour phase, experimental values for the gas solubility of carbon dioxide in aqueous solutions of 1-amino-2-propanol (MIPA) were measured at T = (313.15 and 393.15) K, over the pressure range of (0.2 to 2436.4) kPa. The concentrations of the studied aqueous MIPA solutions were (0.20, 0.30, 0.40, and 0.50) mass fraction. The results of gas solubility are given as the partial pressure of CO{sub 2}, p{sub CO{sub 2}}, against its mole ratio, {alpha}{sub CO{sub 2}} (mol CO{sub 2} {center_dot} mol{sup -1} MIPA), and its mole fraction, x{sub CO{sub 2}}. It is observed that the solubility of CO{sub 2} increases as the concentration of MIPA in solution increases, at a given temperature throughout the pressure range considered; also the solubility values increase, under constant temperature, as the pressure increases in the studied concentration range of MIPA. The physicochemical model of Kent and Eisenberg was used to correlate simultaneously all the experimental results of the solubility of CO{sub 2} in the studied aqueous solutions of MIPA. The model correlates satisfactorily the experimental results. The deviation for pressure was 96.9 kPa using 62 experimental solubility points. The solubility results of carbon dioxide presented in this work are compared with those reported in the literature for aqueous solutions of monoethanolamine (MEA), diethanolamine (DEA), diisopropanolamine (DIPA), and N-methyldiethanolamine (MDEA) and it is possible to conclude that the aqueous solutions of MIPA are an excellent alternative to use in gas purification processes, since the

The concentration of Fe and Zn in food-stuff of agriculture, husbandry and fishery determined by k0-INAA

International Nuclear Information System (INIS)

Th Rina Mulyaningsih

2009-01-01

Deficiency of iron (Fe) and zinc (Zn) micronutrient was suffered by population Therefore the determination of Fe and Zn in agriculture, husbandry, and fishery were carried out. The objective of this research is to estimate Fe and Zn intake through consumed food-stuff. Sampling was done in Pasar Serpong, while Fe and Zn was determined by k 0 - instrumental neutron activation analysis (k 0 -INAA). The result of analysis indicated that concentration of Fe and Zn in beef, goat and goat liver were >150 µg/g, in chicken flesh were around 30 µg/g. This food-stuff is good as source intake of Fe and Zn, due to level of consumption was low i.e. 0.001 - 0.018 kg/day, so its intake was lower enough i.e. 0.1 - 0.5 mg/day. The concentration of Fe and Zn in rice were < 50 µg/g, but because of consume level is high enough 0.3 kg/day, so Fe and Zn intake from rice is high enough. Zn and Fe content in spinach is 119 µg/g and 248 µg/g, Zn and Fe content in Kangkung is 54.84 µg/g, and 337 µg/g, and with consume level of ~0.015 kg/day it is good source of Zn arid Fe intake i.e 0.8 - 3.5 mg/day. The concentration of Zn in egg was 39.0184 µg/g and Fe was 74.45 µg/g because of level consume is higher than chicken flesh, so Zn and Fe intake from egg is higher than from chicken flesh, i.e. 0.85 - 1.64 mg/day. By knowing Fe and Zn concentration in foodstuff, supported with its consume level, Zn and Fe intake every day can be estimated. (author)

Solubility measurement of iron-selenium compounds under reducing conditions. Research document

International Nuclear Information System (INIS)

Kitamura, Akira; Shibata, Masahiro

2003-03-01

Chemical behavior of selenium (Se), which was one of the important elements for performance assessment of geological disposal of high-level radioactive waste, was investigated under reducing and iron-containing conditions. A washing method for an iron diselenide (FeSe 2 (cr)) reagent with acidic and basic solutions (0.1 and 1 M HCl and 1 M NaOH) was carried out for the purification of FeSe 2 reagent, which was considered to be a solubility limiting solid for Se under the geological disposal conditions. Furthermore, solubility of FeSe 2 (cr) was measured in alkaline solution (pH: 11 - 13) under reducing conditions (E h vs SHE: -0.4 - 0 V), and thermodynamic data on equilibrium reactions between Se in solution and Se precipitate were obtained. The dependencies of solubility values on pH and redox potential (E h : vs. standard hydrogen electrode) were best interpreted that the solubility limiting solid was not FeSe 2 (cr) but Se(cr) and the aqueous species was SeO 3 2- in the present experimental conditions. The equilibrium constant between Se(cr) and SeO 3 2- at zero ionic strength was determined and compared with literature values. The chemical behavior of Se under geological disposal conditions was discussed. (author)

[Effects of iron on azoreduction by Shewanella decolorationis S12].

Science.gov (United States)

Chen, Xing-Juan; Xu, Mei-Ying; Sun, Guo-Ping

2010-01-01

The effects of soluble and insoluble Fe(III) on anaerobic azoreduction by Shewanella decolorationis S12 were examined in a series of experiments. Results showed that the effects of iron on anaerobic azoreduction depended on the solubility and concentration of the compounds. Azoreduction was inhibited by insoluble Fe(III) and 0.05-2 mmol/L Fe2 O3 all decelerated the azoreduction activity of 0.2 mmol/L amaranth, but the increase in the concentrations of Fe2O3 did not cause an increasing inhibition. Soluble Fe(III) of which concentration less than 0.4 mmol/L enhanced azoreduction activity of 0.2 mmol/L amaranth but there was no linear relationship between the concentration of soluble Fe(III) and azoreduction activity. Soluble Fe(III) of which concentration more than 1 mmol/L inhibited azoreduction activity of 0.2 mmol/L amaranth and an increasing concentration resulted in an increased inhibition. The inhibition was strengthened under the conditions of limited electron donor. On the other hand, soluble Fe(III) and Fe(II) could relieve the inhibition of azoreduction by dicumarol which blocked quinone cycle. It suggests that in addition to quinone cycle, there is a Fe(III) Fe(II) cycle shuttling electrons in cytoplasmic and periplasmic environment. That is the reason why low concentration of soluble Fe(III) or Fe (II) can enhance azoreduction of S. decolorationis S12. It also indicates that insoluble Fe(III) and high concentration of soluble Fe(III) do compete with azo dye for electrons once it acts as electron acceptor. Thus, when iron and azo dye coexisted, iron could serve as an electron transfer agent or electron competitive inhibitor for anaerobic azoreduction under different conditions. High efficiency of azoreduction can be achieved through controlling the solubility and concentration of irons.

Deposition and solubility of airborne metals to four plant species grown at varying distances from two heavily trafficked roads in London

International Nuclear Information System (INIS)

Peachey, C.J.; Sinnett, D.; Wilkinson, M.; Morgan, G.W.; Freer-Smith, P.H.; Hutchings, T.R.

2009-01-01

In urban areas, a highly variable mixture of pollutants is deposited as particulate matter. The concentration and bioavailability of individual pollutants within particles need to be characterised to ascertain the risks to ecological receptors. This study, carried out at two urban parks, measured the deposition and water-solubility of metals to four species common to UK urban areas. Foliar Cd, Cr, Cu, Fe, Ni, Pb and Zn concentrations were elevated in at least one species compared with those from a rural control site. Concentrations were, however, only affected by distance to road in nettle and, to a lesser extent, birch leaves. Greater concentrations of metal were observed in these species compared to cypress and maple possibly due to differences in plant morphology and leaf surfaces. Solubility appeared to be linked to the size fraction and, therefore, origin of the metal with those present predominantly in the coarse fraction exhibiting low solubility. - High density traffic resulted in elevated metal concentrations on vegetation, which were related to distance from road and plant species.

Deposition and solubility of airborne metals to four plant species grown at varying distances from two heavily trafficked roads in London

Energy Technology Data Exchange (ETDEWEB)

Peachey, C.J. [Forest Research, Centre for Forestry and Climate Change, Alice Holt Lodge, Farnham, Surrey GU10 4LH (United Kingdom); Sinnett, D., E-mail: danielle.sinnett@forestry.gsi.gov.u [Forest Research, Centre for Forestry and Climate Change, Alice Holt Lodge, Farnham, Surrey GU10 4LH (United Kingdom); Wilkinson, M., E-mail: matthew.wilkinson@forestry.gsi.gov.u [Forest Research, Centre for Forestry and Climate Change, Alice Holt Lodge, Farnham, Surrey GU10 4LH (United Kingdom); Morgan, G.W., E-mail: geoff.morgan@forestry.gsi.gov.u [Forest Research, Centre for Forestry and Climate Change, Alice Holt Lodge, Farnham, Surrey GU10 4LH (United Kingdom); Freer-Smith, P.H., E-mail: peter.freer-smith@forestry.gsi.gov.u [Forest Research, Centre for Forestry and Climate Change, Alice Holt Lodge, Farnham, Surrey GU10 4LH (United Kingdom); Hutchings, T.R., E-mail: tony.hutchings@forestry.gsi.gov.u [Forest Research, Centre for Forestry and Climate Change, Alice Holt Lodge, Farnham, Surrey GU10 4LH (United Kingdom)

2009-08-15

In urban areas, a highly variable mixture of pollutants is deposited as particulate matter. The concentration and bioavailability of individual pollutants within particles need to be characterised to ascertain the risks to ecological receptors. This study, carried out at two urban parks, measured the deposition and water-solubility of metals to four species common to UK urban areas. Foliar Cd, Cr, Cu, Fe, Ni, Pb and Zn concentrations were elevated in at least one species compared with those from a rural control site. Concentrations were, however, only affected by distance to road in nettle and, to a lesser extent, birch leaves. Greater concentrations of metal were observed in these species compared to cypress and maple possibly due to differences in plant morphology and leaf surfaces. Solubility appeared to be linked to the size fraction and, therefore, origin of the metal with those present predominantly in the coarse fraction exhibiting low solubility. - High density traffic resulted in elevated metal concentrations on vegetation, which were related to distance from road and plant species.

Solid-state phase equilibria in the Fe-Pt-Pr ternary system at 1173 K

International Nuclear Information System (INIS)

Ren Jing; Gu Zhengfei; Cheng Gang; Zhou Huaiying

2005-01-01

The solid-state phase equilibria in the Fe-Pt-Pr ternary system at 1173 K (Pr ≤ 70%) were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersion spectroscopy (EDS) techniques. The 1173 K isothermal section consists of 13 single-phase regions, 22 two-phase regions and 10 three-phase regions. At 1173 K, we have observed that the maximum solid solubility of Pt in α-Fe is below 1.5 at.% and the solid solution region of Pt in γ-Fe is from 2 to 35 at.%; the maximum solid solubility of Fe in Pt is 18 at.%. The maximum solubility of Fe in PrPt 5 , PrPt 3 , PrPt 2 , Pr 3 Pt 4 , PrPt, Pr 3 Pt 2 and Pr 7 Pt 3 is below 1 at.%. The maximum solubility of Pr in α-(Fe, Pt), γ-(Fe, Pt), FePt, FePt 3 and (Pt, Fe) (the solid solution of Fe in Pt) is 6, 2, 4, 4.5 and 1.5 at.%, respectively. In this work, it is found that the phase Pr 3 Pt 4 does not exist in the ternary system. The binary compounds Fe 7 Pr and Fe 2 Pr and any new ternary compounds were not observed

The Calculation of Fe-Al-O Interaction Coefficient

International Nuclear Information System (INIS)

Kuo, Chin-Guo

2010-01-01

Aluminum is a very common deoxidizer in steel-making processes. The solubility of oxygen in molten iron decreases with increasing aluminum content. For the deoxidation process, the solubility of oxygen in Fe-Al melts decreases with increasing aluminum content. When %Al is increased to 0.34 wt.%, %O decreases to 6.4 ppm, which is the lowest point of the FeAl 2 O 4 curve. Then the Al 2 O 3 curve appears and replaces the FeAl 2 O 4 curve, where the interconnection point of the two curves is the coexistence point of FeAl 2 O 4 and Al 2 O 3 phases. When %Al is increased to 0.4%, the %O decreases to 6.35 ppm, which is the lowest point of the Al 2 O 3 curve. The solubility of oxygen in Fe-Al alloys is about 6.35 ppm with 0.4 wt.% aluminum at 1873 K. Liquid FeO-Al 2 O 3 , hercynite (FeAl 2 O 4 ), and alumina (Al 2 O 3 ) are three possible products during the deoxidation process. Based on thermodynamic calculation, the value of the interaction coefficient of e o Al was determined as -0.75 at 1873 K. This value is in good agreement with experimental curves in the literature.

Soluble iron nutrients in Saharan dust over the central Amazon rainforest

Science.gov (United States)

Rizzolo, Joana A.; Barbosa, Cybelli G. G.; Borillo, Guilherme C.; Godoi, Ana F. L.; Souza, Rodrigo A. F.; Andreoli, Rita V.; Manzi, Antônio O.; Sá, Marta O.; Alves, Eliane G.; Pöhlker, Christopher; Angelis, Isabella H.; Ditas, Florian; Saturno, Jorge; Moran-Zuloaga, Daniel; Rizzo, Luciana V.; Rosário, Nilton E.; Pauliquevis, Theotonio; Santos, Rosa M. N.; Yamamoto, Carlos I.; Andreae, Meinrat O.; Artaxo, Paulo; Taylor, Philip E.; Godoi, Ricardo H. M.

2017-02-01

The intercontinental transport of aerosols from the Sahara desert plays a significant role in nutrient cycles in the Amazon rainforest, since it carries many types of minerals to these otherwise low-fertility lands. Iron is one of the micronutrients essential for plant growth, and its long-range transport might be an important source for the iron-limited Amazon rainforest. This study assesses the bioavailability of iron Fe(II) and Fe(III) in the particulate matter over the Amazon forest, which was transported from the Sahara desert (for the sake of our discussion, this term also includes the Sahel region). The sampling campaign was carried out above and below the forest canopy at the ATTO site (Amazon Tall Tower Observatory), a near-pristine area in the central Amazon Basin, from March to April 2015. Measurements reached peak concentrations for soluble Fe(III) (48 ng m-3), Fe(II) (16 ng m-3), Na (470 ng m-3), Ca (194 ng m-3), K (65 ng m-3), and Mg (89 ng m-3) during a time period of dust transport from the Sahara, as confirmed by ground-based and satellite remote sensing data and air mass backward trajectories. Dust sampled above the Amazon canopy included primary biological aerosols and other coarse particles up to 12 µm in diameter. Atmospheric transport of weathered Saharan dust, followed by surface deposition, resulted in substantial iron bioavailability across the rainforest canopy. The seasonal deposition of dust, rich in soluble iron, and other minerals is likely to assist both bacteria and fungi within the topsoil and on canopy surfaces, and especially benefit highly bioabsorbent species. In this scenario, Saharan dust can provide essential macronutrients and micronutrients to plant roots, and also directly to plant leaves. The influence of this input on the ecology of the forest canopy and topsoil is discussed, and we argue that this influence would likely be different from that of nutrients from the weathered Amazon bedrock, which otherwise provides the

Experimental determination of the phase equilibria in the Co-Fe-Zr ternary system

International Nuclear Information System (INIS)

Wang, C.P.; Yu, Y.; Zhang, H.H.; Hu, H.F.; Liu, X.J.

2011-01-01

Research highlights: → We determined four isothermal sections of the Co-Fe-Zr system from 1000 o C to 1300 o C. → No ternary compound was found in the Co-Fe-Zr ternary system. → The solubility of Fe in the liquid phase at 1300 o C is extremely large. → The (Co, Fe) 2 Zr phase form the continuous solution from Co-Zr side to Fe-Zr side. → The solubility of Zr in the fcc (Co, Fe) phase is extremely small. - Abstract: The phase equilibria in the Co-Fe-Zr ternary system were investigated by means of optical microscopy (OM), electron probe microanalysis (EPMA), X-ray diffraction (XRD), and differential scanning calorimetry (DSC) on equilibrated ternary alloys. Four isothermal sections of the Co-Fe-Zr ternary system at 1300 o C, 1200 o C, 1100 o C and 1000 o C were experimentally established. The experimental results indicate that (1) no ternary compound was found in this system; (2) the solubility of Fe in the liquid phase of the Co-rich corner at 1300 o C is extremely large; (3) the liquid phase in the Zr-rich corner and the (Co,Fe) 2 Zr phase form the continuous solid solutions from the Co-Zr side to the Fe-Zr side; (4) the solubility of Zr in the fcc (Co, Fe) phase is extremely small.

A soluble envelope protein of endogenous retrovirus (FeLIX) present in serum of domestic cats mediates infection of a pathogenic variant of feline leukemia virus.

Science.gov (United States)

Sakaguchi, Shoichi; Shojima, Takayuki; Fukui, Daisuke; Miyazawa, Takayuki

2015-03-01

T-lymphotropic feline leukemia virus (FeLV-T), a highly pathogenic variant of FeLV, induces severe immunosuppression in cats. FeLV-T is fusion defective because in its PHQ motif, a gammaretroviral consensus motif in the N terminus of an envelope protein, histidine is replaced with aspartate. Infection by FeLV-T requires FeLIX, a truncated envelope protein encoded by an endogenous FeLV, for transactivation of infectivity and Pit1 for binding FeLIX. Although Pit1 is present in most tissues in cats, the expression of FeLIX is limited to certain cells in lymphoid organs. Therefore, the host cell range of FeLV-T was thought to be restricted to cells expressing FeLIX. However, because FeLIX is a soluble factor and is expressed constitutively in lymphoid organs, we presumed it to be present in blood and evaluated its activities in sera of various mammalian species using a pseudotype assay. We demonstrated that cat serum has FeLIX activity at a functional level, suggesting that FeLIX is present in the blood and that FeLV-T may be able to infect cells expressing Pit1 regardless of the expression of FeLIX in vivo. In addition, FeLIX activities in sera were detected only in domestic cats and not in other feline species tested. To our knowledge, this is the first report to prove that a large amount of truncated envelope protein of endogenous retrovirus is circulating in the blood to facilitate the infection of a pathogenic exogenous retrovirus. © 2015 The Authors.

Biogeochemical speciation of Fe in ocean water

NARCIS (Netherlands)

Hiemstra, T.; Riemsdijk, van W.H.

2006-01-01

The biogeochemical speciation of Fe in seawater has been evaluated using the consistent Non-Ideal Competitive Adsorption model (NICA¿Donnan model). Two types of data sets were used, i.e. Fe-hydroxide solubility data and competitive ligand equilibration/cathodic stripping voltammetry (CLE/CSV) Fe

Variation of Soluble Solids Concentration During the Day in Three Pastures During the Dry Season in the Middle River Sinú Valley

Directory of Open Access Journals (Sweden)

Emiro Suárez Paternina

2015-07-01

Full Text Available The aim of this study was to determine the concentration of soluble solids at different times of the day in three tropical pastures. The experiment was conducted at the Research Center Turipaná of Colombian Agricultural Research Corporation, located in Cereté, Colombia. During January and February of 2011, we assessed the concentration of soluble solids in three fertirrigated pastures: Panicum maximum, Cynodon nlemfuensis and Brachiaria hybrid cv. Mulato II, in an intensive model of meat production at different sampling times 7:00 and 10:00 a. m., 1:00 and 4:00 p.m. The statistical design of the experiment consisted of a block design completely randomized three-factor under 3*3*4 (pasture*stocking*time and three replicates for each evaluation day. An analysis of variance and differences were statistically significant when the means were separated by Tukey test (p<0.05. The analysis found highly significant differences (p<0.01 in the concentration of soluble solids in different pastures, in all periods of the day evaluated, with the cultivar Mulato II that presented the highest values with 9.19 %, followed by Cynodon nlemfuensis and Panicum maximum with 8.27 % and 7.07 %, respectively. The soluble solids concentration varied during the day and between pastures. The time periods close to noon —10:00 a. m. and 1:00 p. m.— presented the highest concentrations of soluble solids in all pastures; this can be used as a tool for paddock rotation.

The problem of intermixing of metals possessing no mutual solubility upon explosion welding (Cu-Ta, Fe-Ag, Al-Ta)

Energy Technology Data Exchange (ETDEWEB)

Greenberg, B.A., E-mail: bella@imp.uran.ru [Institute of Metal Physics, Ural Branch, Russian Academy of Sciences, S. Kovalevskoi str. 18, Ekaterinburg, 620990 (Russian Federation); Ivanov, M.A. [Kurdyumov Institute of Metal Physics, National Academy of Sciences of Ukraine, Vernadskogo blvd. 36, Kiev, 03680 (Ukraine); Rybin, V.V. [State Polytechnical University, Politekhnicheskaya str. 29, St. Petersburg, 195251 (Russian Federation); Elkina, O.A.; Antonova, O.V.; Patselov, A.M.; Inozemtsev, A.V.; Plotnikov, A.V.; Volkova, A.Yu. [Institute of Metal Physics, Ural Branch, Russian Academy of Sciences, S. Kovalevskoi str. 18, Ekaterinburg, 620990 (Russian Federation); Besshaposhnikov, Yu.P. [OJSC Ural Chemical Machine Building Plant, Khibinogorskii Lane 33, Ekaterinburg, 620010 (Russian Federation)

2013-01-15

On the basis of the results obtained for joints of dissimilar metals such as copper-tantalum and iron-silver, the reason of immiscible suspensions mixing upon explosion welding has been cleared out. It has been found that the interface (plain or wavy) is not smooth and contains inhomogeneities, namely, cusps and local melting zones. The role of granulating fragmentation providing partitioning of initial materials as a main channel of input energy dissipation has been revealed. It has been shown that in joints of metals possessing normal solubility the local melting zones are true solutions, but if metals possess no mutual solubility the local melting zones are colloidal solutions. Realization of either emulsion or suspension variant takes place. The results can be used in the development of new joints of metals possessing no mutual solubility. - Highlights: Black-Right-Pointing-Pointer Immiscible pairs Ta/Cu and Fe/Ag are welded successfully by explosive welding. Black-Right-Pointing-Pointer Fragmentation provides for partitioning as the main energy dissipation channel. Black-Right-Pointing-Pointer Immiscible metals form colloidal solid solutions during solidification. Black-Right-Pointing-Pointer Melting and boiling temperatures ratio determines the colloidal solution type. Black-Right-Pointing-Pointer Local melting zones being in suspension form enhance welds hardening.

On the americium oxalate solubility

International Nuclear Information System (INIS)

Zakolupin, S.A.; Korablin, Eh.V.

1977-01-01

The americium oxalate solubility at different nitric (0.0-1 M) and oxalic (0.0-0.4 M) acid concentrations was investigated in the temperature range from 14 to 60 deg C. The dependence of americium oxalate solubility on the oxalic acid concentration was determined. Increasing oxalic acid concentration was found to reduce the americium oxalate solubility. The dependence of americium oxalate solubility on the oxalic acid concentration was noted to be a minimum at low acidity (0.1-0.3 M nitric acid). This is most likely due to Am(C 2 O 4 ) + , Am(C 2 O 4 ) 2 - and Am(C 2 O 4 ) 3 3- complex ion formation which have different unstability constants. On the basis of the data obtained, a preliminary estimate was carried out for the product of americium oxalate solubility in nitric acid medium (10 -29 -10 -31 ) and of the one in water (6.4x10 -20 )

Factors controlling the solubility of trace metals in atmospheric aerosols over the Eastern Mediterranean

Science.gov (United States)

Nikolaou, Panagiota; Mihalopoulos, Nikolaos; Kanakidou, Maria

2015-04-01

Atmospheric input of aerosols is recognized, as an important source of nutrients, for the oceans. The chemical interactions between aerosols and varying composition of air masses lead to different coating of their surfaces with sulfate, nitrate and organic compounds, increasing their solubility and their role as a carrier of nutrients and pollutants in ecosystems. Recent works have highlighted that atmospheric inputs of nutrients and trace metals can considerably influence the marine ecosystem functioning at semi-enclosed or enclosed water bodies such as the eastern Mediterranean. The current work aims to determine the sources and the factors controlling the variability of nutrients in the eastern Mediterranean. Special focus has been given on trace elements solubility, considered either as key nutrients for phytoplankton growth such as iron (Fe), phosphorus (P) or inhibitors such as copper (Cu). This has been accomplished by analyzing size segregated aerosol samples collected at the background site of Finokalia in Crete for an entire year. Phosphorus concentrations indicate important increases in air masses influenced both by anthropogenic activities in the northeast European countries and by dust outbreaks. The last is confirmed by the correlation observed between total P and dust concentrations and by the air mass backward trajectories computed by running the NOAA Hysplit Model (Hybrid Single - Particle Langrangian Integrated Trajectory (http://www.arl.noaa.gov/ready/hysplit4.html). Overall 73% of total P has been found to be associated with anthropogenic sources. The solubility of P and Fe has been found to be closely related to the acidity (pH) and dust amount in aerosols. The aerosol pH was predicted using thermodynamic modeling (ISORROPIA-II), meteorological observations (RH, T), and gas/particle observations. More specifically P and Fe solubility appears to be inversely related to the crustal elements levels, while it increases in acidic environment. The

Actinide Solubility and Speciation in the WIPP [PowerPoint

International Nuclear Information System (INIS)

Reed, Donald T.

2015-01-01

The presentation begins with the role and need for nuclear repositories (overall concept, international updates (Sweden, Finland, France, China), US approach and current status), then moves on to the WIPP TRU repository concept (design, current status--safety incidents of February 5 and 14, 2014, path forward), and finally considers the WIPP safety case: dissolved actinide concentrations (overall approach, oxidation state distribution and redox control, solubility of actinides, colloidal contribution and microbial effects). The following conclusions are set forth: (1) International programs are moving forward, but at a very slow and somewhat sporadic pace. (2) In the United States, the Salt repository concept, from the perspective of the long-term safety case, remains a viable option for nuclear waste management despite the current operational issues/concerns. (3) Current model/PA prediction (WIPP example) are built on redundant conservatisms. These conservatisms are being addressed in the ongoing and future research to fill existing data gaps--redox control of plutonium by Fe(0, II), thorium (analog) solubility studies in simulated brine, contribution of intrinsic and biocolloids to the mobile concentration, and clarification of microbial ecology and effects.

Actinide Solubility and Speciation in the WIPP [PowerPoint

Energy Technology Data Exchange (ETDEWEB)

Reed, Donald T. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-11-02

The presentation begins with the role and need for nuclear repositories (overall concept, international updates (Sweden, Finland, France, China), US approach and current status), then moves on to the WIPP TRU repository concept (design, current status--safety incidents of February 5 and 14, 2014, path forward), and finally considers the WIPP safety case: dissolved actinide concentrations (overall approach, oxidation state distribution and redox control, solubility of actinides, colloidal contribution and microbial effects). The following conclusions are set forth: (1) International programs are moving forward, but at a very slow and somewhat sporadic pace. (2) In the United States, the Salt repository concept, from the perspective of the long-term safety case, remains a viable option for nuclear waste management despite the current operational issues/concerns. (3) Current model/PA prediction (WIPP example) are built on redundant conservatisms. These conservatisms are being addressed in the ongoing and future research to fill existing data gaps--redox control of plutonium by Fe(0, II), thorium (analog) solubility studies in simulated brine, contribution of intrinsic and biocolloids to the mobile concentration, and clarification of microbial ecology and effects.

Solubility Products of M(II) - Carbonates

Energy Technology Data Exchange (ETDEWEB)

Grauer, Rolf; Berner, Urs [ed.

1999-01-01

Many solubility data for M(II) carbonates commonly compiled in tables are contradictory and sometimes obviously wrong. The quality of such data has been evaluated based on the original publications and reliable solubility constants have been selected for the carbonates of Mn, Fe, Co, Ni, Cu, Zn, Cd and Pb with the help of cross-comparisons. (author) translated from a PSI internal report written in German in 1994 (TM-44-94-05). 5 figs., 1 tab., 68 refs.

Increased serum concentrations of soluble ST2 predict mortality after burn injury.

Science.gov (United States)

Hacker, Stefan; Dieplinger, Benjamin; Werba, Gregor; Nickl, Stefanie; Roth, Georg A; Krenn, Claus G; Mueller, Thomas; Ankersmit, Hendrik J; Haider, Thomas

2018-06-27

Large burn injuries induce a systemic response in affected patients. Soluble ST2 (sST2) acts as a decoy receptor for interleukin-33 (IL-33) and has immunosuppressive effects. sST2 has been described previously as a prognostic serum marker. Our aim was to evaluate serum concentrations of sST2 and IL-33 after thermal injury and elucidate whether sST2 is associated with mortality in these patients. We included 32 burn patients (total body surface area [TBSA] >10%) admitted to our burn intensive care unit and compared them to eight healthy probands. Serum concentrations of sST2 and IL-33 were measured serially using an enzyme-linked immunosorbent assay (ELISA) technique. The mean TBSA was 32.5%±19.6%. Six patients (18.8%) died during the hospital stay. Serum analyses showed significantly increased concentrations of sST2 and reduced concentrations of IL-33 in burn patients compared to healthy controls. In our study cohort, higher serum concentrations of sST2 were a strong independent predictor of mortality. Burn injuries cause an increment of sST2 serum concentrations with a concomitant reduction of IL-33. Higher concentrations of sST2 are associated with increased in-hospital mortality in burn patients.

Daily rhythm of circulating fat soluble vitamin concentration (A, D, E and K in the horse

Directory of Open Access Journals (Sweden)

Caola Giovanni

2004-07-01

Full Text Available Abstract Background Many physiological processes of mammalian species exhibit daily rhythmicity. An intrinsic relationship exists between fat soluble vitamins (A, D, E and K and several body functions. Few investigations on the rhythmic pattern of vitamins in domestic animals have been carried out. The present study evaluated the circadian rhythmicity of fat soluble vitamins in the horse. Methods Blood samples from 5 Thoroughbred mares were collected at four-hour intervals over a 48-hour period (starting at 8:00 hours on day 1 and finishing at 4:00 on day 2 via an intravenous cannula inserted into the jugular vein. Fat soluble vitamin concentration in the serum (A, D, E and K was measured by HPLC. One-way repeated measures analysis of variance (ANOVA was used to determine significant differences. p values Results ANOVA showed a highly significant effect of time in all the horses for the vitamins studied (p Conclusion Fat soluble vitamins exhibit daily rhythmicity with diurnal peak. Further investigations could help optimize the use of these substances according to their circadian (or other rhythms.

Effect of pH and chloride concentration on the removal of hexavalent chromium in a batch electrocoagulation reactor

International Nuclear Information System (INIS)

Arroyo, M.G.; Perez-Herranz, V.; Montanes, M.T.; Garcia-Anton, J.; Guinon, J.L.

2009-01-01

In this work, the effect of pH and chloride ions concentration on the removal of Cr(VI) from wastewater by batch electrocoagulation using iron plate electrodes has been investigated. The initial solution pH was adjusted with different concentrations of H 2 SO 4 . The presence of chloride ions enhances the anode dissolution due to pitting corrosion. Fe 2+ ions formed during the anode dissolution cause the reduction of Cr(VI) to form Cr(III), which are co-precipitated with Fe 3+ ions at relatively low pH. The reduction degree of Cr(VI) to Cr(III) and the solubility of metal hydroxide species (both chromic and iron hydroxides) depend on pH. At higher concentrations of H 2 SO 4 , the reduction of Cr(VI) to Cr(III) by Fe 2+ ions is preferred, but the coagulation of Fe 3+ and Cr(III) is favoured at the lower H 2 SO 4 concentrations.

Effect of pH and chloride concentration on the removal of hexavalent chromium in a batch electrocoagulation reactor

Energy Technology Data Exchange (ETDEWEB)

Arroyo, M.G. [Departamento de Ingenieria Quimica y Nuclear, Universidad Politecnica de Valencia, Camino de Vera s/n, 46022 Valencia (Spain); Perez-Herranz, V., E-mail: vperez@iqn.upv.es [Departamento de Ingenieria Quimica y Nuclear, Universidad Politecnica de Valencia, Camino de Vera s/n, 46022 Valencia (Spain); Montanes, M.T.; Garcia-Anton, J.; Guinon, J.L. [Departamento de Ingenieria Quimica y Nuclear, Universidad Politecnica de Valencia, Camino de Vera s/n, 46022 Valencia (Spain)

2009-09-30

In this work, the effect of pH and chloride ions concentration on the removal of Cr(VI) from wastewater by batch electrocoagulation using iron plate electrodes has been investigated. The initial solution pH was adjusted with different concentrations of H{sub 2}SO{sub 4}. The presence of chloride ions enhances the anode dissolution due to pitting corrosion. Fe{sup 2+} ions formed during the anode dissolution cause the reduction of Cr(VI) to form Cr(III), which are co-precipitated with Fe{sup 3+} ions at relatively low pH. The reduction degree of Cr(VI) to Cr(III) and the solubility of metal hydroxide species (both chromic and iron hydroxides) depend on pH. At higher concentrations of H{sub 2}SO{sub 4}, the reduction of Cr(VI) to Cr(III) by Fe{sup 2+} ions is preferred, but the coagulation of Fe{sup 3+} and Cr(III) is favoured at the lower H{sub 2}SO{sub 4} concentrations.

Rates of cuticular penetration of chelated Fe(III): role of humidity, concentration, adjuvants, temperature, and type of chelate.

Science.gov (United States)

Schönherr, Jörg; Fernández, Victoria; Schreiber, Lukas

2005-06-01

Time courses of cuticular penetration of FeCl3 and Fe(III) complexes of citric acid, EDTA, EDDHA (Sequestrene 138Fe), imidodisuccinic acid (IDHA), and ligninsulfonic acid (Natrel) were studied using astomatous cuticular membranes (CMs) isolated from Populus x canescens leaves. At 100% relative humidity, the Fe(III) chelates disappeared exponentially with time from the surface of the CMs; that is, penetration was a first-order process that can be described using rate constants or half-times of penetration (t(1/2)). Half-times ranged from 20 to 30 h. At 90% humidity, penetration rates were insignificant with the exception of Natrel, for which t(1/2) amounted to 58 h. Rate constants were independent of temperature (15, 25, and 35 degrees C). Permeability decreased with increasing Fe chelate concentration (IDHA and EDTA). At 100% humidity, half-times measured with FeIDHA were 11 h (2 mmol L(-1)), 17 h (10 mmol L(-1)) and 36 h (20 mmol L(-1)), respectively. In the presence of FeEDTA, penetration of CaCl2 was slowed greatly. Half-times for penetration of CaCl2, which were 1.9 h in the absence of FeEDTA, rose to 3.12 h in the presence of an equimolar concentration of EDTA and 13.3 h when the FeEDTA concentration was doubled. Hence, Fe chelates reduced permeability of CMs to CaCl2 and to the Fe chelates themselves. It is suggested that Fe chelates reduced the size of aqueous pores. This view is supported by the fact that rate constants for calcium salts were about 5 times higher than for Fe chelates with the same molecular weights. Adding Tween 20 (5 g L(-1)) as a humectant did not increase permeability to FeIDHA at 90% humidity and below, while addition of glycine betaine did. Penetration of FeCl3 applied at 5 g L(-1) (pH 1.5) was not a first order process as rate constants decreased rapidly with time. Only 2% of the dose penetrated during the first 2 h and less than that in the subsequent 8 h. Recovery was only 70%. This was attributed to the formation of insoluble Fe

Fractional iron solubility of aerosol particles enhanced by biomass burning and ship emission in Shanghai, East China.

Science.gov (United States)

Fu, H B; Shang, G F; Lin, J; Hu, Y J; Hu, Q Q; Guo, L; Zhang, Y C; Chen, J M

2014-05-15

In terms of understanding Fe mobilization from aerosol particles in East China, the PM2.5 particles were collected in spring at Shanghai. Combined with the backtrajectory analysis, the PM2.5/PM10 and Ca/Al ratios, a serious dust-storm episode (DSE) during the sampling was identified. The single-particle analysis showed that the major iron-bearing class is the aluminosilicate dust during DSE, while the Fe-bearing aerosols are dominated by coal fly ash, followed by a minority of iron oxides during the non-dust storm days (NDS). Chemical analyses of samples showed that the fractional Fe solubility (%FeS) is much higher during NDS than that during DSE, and a strong inverse relationship of R(2)=0.967 between %FeS and total atmospheric iron loading were found, suggested that total Fe (FeT) is not controlling soluble Fe (FeS) during the sampling. Furthermore, no relationship between FeS and any of acidic species was established, suggesting that acidic process on aerosol surfaces are not involved in the trend of iron solubility. It was thus proposed that the source-dependent composition of aerosol particles is a primary determinant for %FeS. Specially, the Al/Fe ratio is poorly correlated (R(2)=0.113) with %FeS, while the apparent relationship between %FeS and the calculated KBB(+)/Fe ratio (R(2)=0.888) and the V/Fe ratio (R(2)=0.736) were observed, reflecting that %FeS could be controlled by both biomass burning and oil ash from ship emission, rather than mineral particles and coal fly ash, although the latter two are the main contributors to the atmospheric Fe loading during the sampling. Such information can be useful improving our understanding on iron solubility on East China, which may further correlate with iron bioavailability to the ocean, as well as human health effects associated with exposure to fine Fe-rich particles in densely populated metropolis in China. Copyright © 2014 Elsevier B.V. All rights reserved.

Thermodynamic modeling of neptunium(V) solubility in concentrated Na-CO3-HCO3-Cl-ClO4-H-OH-H2O systems

International Nuclear Information System (INIS)

Novak, C.F.; Roberts, K.E.

1994-01-01

Safety assessments of nuclear waste repositories often require estimation of actinide solubilities as a function of groundwater composition. Although considerable amount of research has been done on the solubility and speciation of actinides, relatively little has been done to unify these data into a model applicable to concentrate brines. Numerous authors report data on the aqueous chemical properties of Np(V) in NaClO 4 , Na 2 CO 3 , and NaCl media, but a consistent thermodynamic model for predicting these properties is not available. To meet this need, a model was developed to describe the solubility of Np(V) in Na-Cl-ClO 4 -CO 3 aqueous systems, based on the Pitzer activity coefficient formalism for concentrated electrolytes. Hydrolysis and/or carbonate complexation are the dominant aqueous reactions with neptunyl in these systems. Literature data for neptunyl extraction and solubility, and solubility data that the authors developed, are used to parameterize an integrated model for Np(V) solubility in the Np(V)-Na-CO 3 -HCO 3 -Cl-ClO 4 -H-OH-H 2 O system. The resulting model is tested against additional solubility data, and compared with Np(V) solubility experiments in complex synthetic brines

Study of hydrogenation of Sm2Fe17-yGay by means of X-ray diffraction

International Nuclear Information System (INIS)

Teresiak, A.; Uhlemann, M.; Kubis, M.; Gebel, B.; Mattern, N.; Mueller, K.-H.

2000-01-01

The hydrogenation process of Sm 2 Fe 17-y Ga y (y=0-2) was studied. X-ray investigations show a decreasing hydrogen solubility in the intermetallic alloy with increasing Ga-content from 4.0±0.3 atoms per formula unit for Sm 2 Fe 17 to 2.85±0.05 for Sm 2 Fe 15 Ga 2 . The larger Ga atoms reduce the size of the interstitial sites and thereby the maximum hydrogen concentration is decreased. The behaviour of the lattice parameters a and c with increasing Ga content points to a changed hydrogen distribution on the interstitial sites, becoming more statistical. In situ observations by means of high temperature X-ray diffraction show that the hydrogen absorption process is diffusion controlled. The hydrogen absorption starts at an annealing temperature of 120-140 C in all cases. The solubility of hydrogen decreases with increasing temperature. The hydrogen is completely desorbed above 350 C in all cases. The absorption/desorption process is reversible between room temperature and 400 C. Annealing at temperatures above 400 C leads to the decomposition of the Sm 2 Fe 17 phase, indicated by emerging of α-Fe. The formation of SmH x is established at 600 C. The decomposition temperature increases with increasing Ga-content. Up to 750 C, only Sm 2 Fe 17 is completely decomposed. (orig.)

Drastic effect of the Mn-substitution in the strongly correlated semiconductor FeSb2.

Science.gov (United States)

Kassem, Mohamed A.; Tabata, Yoshikazu; Waki, Takeshi; Nakamura, Hiroyuki

2017-06-01

We report the effects of Mn substitution, corresponding to hole doping, on the electronic properties of the narrow gap semiconductor, FeSb2, using single crystals of Fe1- x Mn x Sb2 grown by the Sb flux method. The orthorhombic Pnnm structure was confirmed by powder X-ray diffraction (XRD) for the pure and Mn-substituted samples. Their crystal structure parameters were refined using the Rietveld method. The chemical composition was investigated by wavelength-dispersive X-ray spectroscopy (WDX). The solubility limit of Mn in FeSb2 is x max ˜ 0.05 and the lattice constants change monotonically with increasing the actual Mn concentration. A drastic change from semiconducting to metallic electronic transports was found at very low Mn concentration at x ˜ 0.01. Our experimental results and analysis indicate that the substitution of a small amount of Mn changes drastically the electronic state in FeSb2 as well as the Co-substitution does: closing of the narrow gap and emergence of the density of states (DOS) at the Fermi level.

Chemical consequences of the nuclear reactions 58Fe(n,γ)59Fe and 57Co(EC)57Fe in soluble Prussian Blue

DEFF Research Database (Denmark)

Fenger, Jes; Maddock, A. G.; Siekierska, K. E.

1970-01-01

KFe[Fe(CN)6],H2O was prepared with 58Fe in either the cation or the complex, and both samples were neutron-irradiated and analysed for free and complexed 59Fe. Parallel experiments were performed on K4[Fe(CN)6],3H2O. In Prussian Blue the retention in the hexacyano-complex is ca. 5% and can be inc...

Disproportionation of hydroxylamine by water-soluble iron(III) porphyrinate compounds.

Science.gov (United States)

Bari, Sara E; Amorebieta, Valentín T; Gutiérrez, María M; Olabe, José A; Doctorovich, Fabio

2010-01-01

The reactions of hydroxylamine (HA) with several water-soluble iron(III) porphyrinate compounds, namely iron(III) meso-tetrakis-(N-ethylpyridinium-2yl)-porphyrinate ([Fe(III)(TEPyP)](5+)), iron(III) meso-tetrakis-(4-sulphonatophenyl)-porphyrinate ([Fe(III)(TPPS)](3-)), and microperoxidase 11 ([Fe(III)(MP11)]) were studied for different [Fe(III)(Porph)]/[HA] ratios, under anaerobic conditions at neutral pH. Efficient catalytic processes leading to the disproportionation of HA by these iron(III) porphyrinates were evidenced for the first time. As a common feature, only N(2) and N(2)O were found as gaseous, nitrogen-containing oxidation products, while NH(3) was the unique reduced species detected. Different N(2)/N(2)O ratios obtained with these three porphyrinates strongly suggest distinctive mechanistic scenarios: while [Fe(III)(TEPyP)](5+) and [Fe(III)(MP11)] formed unknown steady-state porphyrinic intermediates in the presence of HA, [Fe(III)(TPPS)](3-) led to the well characterized soluble intermediate, [Fe(II)(TPPS)NO](4-). Free-radical formation was only evidenced for [Fe(III)(TEPyP)](5+), as a consequence of a metal centered reduction. We discuss the catalytic pathways of HA disproportionation on the basis of the distribution of gaseous products, free radicals formation, the nature of porphyrinic intermediates, the Fe(II)/Fe(III) redox potential, the coordinating capabilities of each complex, and the kinetic analysis. The absence of NO(2)(-) revealed either that no HAO-like activity was operative under our reaction conditions, or that NO(2)(-), if formed, was consumed in the reaction milieu.

Elevated concentrations of dissolved Ba, Fe and Mn in a mangrove subterranean estuary: Consequence of sea level rise?

Science.gov (United States)

Sanders, Christian J.; Santos, Isaac R.; Barcellos, Renato; Silva Filho, Emmanoel V.

2012-07-01

Groundwater underlying a mangrove habitat was studied to determine the geochemical nature of Ba, Fe and Mn as related to dissolved organic carbon (DOC), SO4 and salinity (Sepetiba Bay, Brazil). Wells were placed across geobotanic facies and sampled monthly for a year. We observed non-conservative behavior and elevated concentrations of dissolved metals relative to local end-members (i.e., fresh river water and seawater). Average Ba concentrations were near 2000 nM in an area with low salinity (˜5.3). Dissolved Fe (up to 654 μM) was two orders of magnitude greater in fresh groundwater than in the seaward sampling stations. Manganese concentrations were greatest (112 μM) in the high salinity (˜65) zone, being directly influenced by salinity. Groundwater Ba, Fe and Mn showed differing site specific concentrations, likely related to ion exchange processes and redox-controlled cycling along distinct mangrove facies. The results of this work show that metal concentrations are altered relative to conservative mixing between terrestrial and marine endmembers, illustrating the importance of mangrove subterranean estuaries as biogeochemical reactors. Roughly-estimated submarine groundwater discharge-derived dissolved Ba, Fe and Mn fluxes were at least one order of magnitude greater than river-derived fluxes into Sepetiba Bay.

Equilibrium concentration of radionuclides in cement/groundwater/carbon steel system

International Nuclear Information System (INIS)

Keum, D. K.; Cho, W. J.; Hahn, P. S.

1997-01-01

Equilibrium concentration of major elements in an underground repository with a capacity of 100,000 drums have been simulated using the geochemical computer code (EQMOD). The simulation has been carried out at the conditions of pH 12 to 13.5, and Eh 520 and -520 mV. Solubilities of magnesium and calcium decrease with the increase of pH. The solubility of iron increases with pH at Eh -520 mV of reducing environment, while it almost entirely exists as the precipitate of Fe(OH) 3 (s) at Eh 520 mV of oxidizing environment. All of cobalt and nickel are predicted to be dissolved in the liquid phase regardless of pH since the solubility limit is greater than the total concentration. In the case of cesium and strontium, all forms of both ions are present in the liquid phase because they have negligible sorption capacity on cement and large solubility under disposal atmosphere. And thus the total concentration determines the equilibrium concentration. Adsorbed amounts of iodide and carbonate are dependent on adsorption capacity and adsorption equilibrium constant. Especially, the calcite turns out to be a solubility-limiting phase on the carbonate system. In order to validate the model, the equilibrium concentrations measured for a number of systems which consist of iron, cement, synthetic groundwater and radionuclides are compared with those predicted by the model. The concentrations between the model and the experiment of nonadsorptive elements - cesium, strontium, cobalt, nickel and iron, are well agreed. It indicates that the assumptions and the thermodynamic data in this work are valid. Using the adsorption equilibrium constant as a free parameter, the experimental data of iodide and carbonate have been fitted to the model. The model is in a good agreement with the experimental data of the iodide system. (author)

Nitrogen solubility in the deep mantle and the origin of Earth's primordial nitrogen budget

Science.gov (United States)

Yoshioka, Takahiro; Wiedenbeck, Michael; Shcheka, Svyatoslav; Keppler, Hans

2018-04-01

The solubility of nitrogen in the major minerals of the Earth's transition zone and lower mantle (wadsleyite, ringwoodite, bridgmanite, and Ca-silicate perovskite) coexisting with a reduced, nitrogen-rich fluid phase was measured. Experiments were carried out in multi-anvil presses at 14 to 24 GPa and 1100 to 1800 °C close to the Fe-FeO buffer. Starting materials were enriched in 15N and the nitrogen concentrations in run products were measured by secondary ion mass spectrometry. Observed nitrogen (15N) solubilities in wadsleyite and ringwoodite typically range from 10 to 250 μg/g and strongly increase with temperature. Nitrogen solubility in bridgmanite is about 20 μg/g, while Ca-silicate perovskite incorporates about 30 μg/g under comparable conditions. Partition coefficients of nitrogen derived from coexisting phases are DNwadsleyite/olivine = 5.1 ± 2.1, DNringwoodite/wadsleyite = 0.49 ± 0.29, and DNbridgmanite/ringwoodite = 0.24 (+ 0.30 / - 0.19). Nitrogen solubility in the solid, iron-rich metal phase coexisting with the silicates was also measured and reached a maximum of nearly 1 wt.% 15N at 23 GPa and 1400 °C. These data yield a partition coefficient of nitrogen between iron metal and bridgmanite of DNmetal/bridgmanite ∼ 98, implying that in a lower mantle containing about 1% of iron metal, about half of the nitrogen still resides in the silicates. The high nitrogen solubility in wadsleyite and ringwoodite may be responsible for the low nitrogen concentrations often observed in ultradeep diamonds from the transition zone. Overall, the solubility data suggest that the transition zone and the lower mantle have the capacity to store at least 33 times the mass of nitrogen presently residing in the atmosphere. By combining the nitrogen solubility data in minerals with data on nitrogen solubility in silicate melts, mineral/melt partition coefficients of nitrogen can be estimated, from which the behavior of nitrogen during magma ocean crystallization can

Determination of subcellular concentrations of soluble carbohydrates in rose petals during opening by nonaqueous fractionation method combined with infiltration-centrifugation method.

Science.gov (United States)

Yamada, Kunio; Norikoshi, Ryo; Suzuki, Katsumi; Imanishi, Hideo; Ichimura, Kazuo

2009-11-01

Petal growth associated with flower opening depends on cell expansion. To understand the role of soluble carbohydrates in petal cell expansion during flower opening, changes in soluble carbohydrate concentrations in vacuole, cytoplasm and apoplast of petal cells during flower opening in rose (Rosa hybrida L.) were investigated. We determined the subcellular distribution of soluble carbohydrates by combining nonaqueous fractionation method and infiltration-centrifugation method. During petal growth, fructose and glucose rapidly accumulated in the vacuole, reaching a maximum when petals almost reflected. Transmission electron microscopy showed that the volume of vacuole and air space drastically increased with petal growth. Carbohydrate concentration was calculated for each compartment of the petal cells and in petals that almost reflected, glucose and fructose concentrations increased to higher than 100 mM in the vacuole. Osmotic pressure increased in apoplast and symplast during flower opening, and this increase was mainly attributed to increases in fructose and glucose concentrations. No large difference in osmotic pressure due to soluble carbohydrates was observed between the apoplast and symplast before flower opening, but total osmotic pressure was much higher in the symplast than in the apoplast, a difference that was partially attributed to inorganic ions. An increase in osmotic pressure due to the continued accumulation of glucose and fructose in the symplast may facilitate water influx into cells, contributing to cell expansion associated with flower opening under conditions where osmotic pressure is higher in the symplast than in the apoplast.

pH-Dependent isotope exchange and hydrogenation catalysed by water-soluble NiRu complexes as functional models for [NiFe]hydrogenases

OpenAIRE

Kure, Bunsho; Matsumoto, Takahiro; Ichikawa, Koji; Fukuzumi, Shunichi; Higuchi, Yoshiki; Yagi, Tatsuhiko; Ogo, Seiji

2008-01-01

The pH-dependent hydrogen isotope exchange reaction between gaseous isotopes and medium isotopes and hydrogenation of the carbonyl compounds have been investigated with water-soluble bis(mu-thiolate)(mu-hydride)NiRu complexes, Ni(II)(mu-SR)(2)(mu-H)Ru(II) {(mu-SR)(2) = N,N'-dimethyl-N,N'-bis(2-mercaptoethyl)-1,3-propanediamine}, as functional models for [NiFe]hydrogenases. In acidic media (at pH 4-6), the mu-H ligand of the Ni(II)(mu-SR)(2)(mu-H)Ru(II) complexes has H(+) properties, and the c...

THE BEHAVIOR OF SOLUBLE METALS ELUTED FROM Ni/Fe-BASED ALLOY REACTORS AFTER HIGH-TEMPERATURE AND HIGH-PRESSURE WATER PROCESS

Directory of Open Access Journals (Sweden)

M. Faisal

2012-05-01

Full Text Available The behavior of heavy metals eluted from the wall of Ni/Fe-based alloy reactors after high-temperature and high-pressure water reaction were studied at temperatures ranging from 250 to 400oC. For this purpose, water and cysteic acid were heated in two reactor materials which are SUS 316 and Inconel 625. Under the tested conditions, the erratic behaviors of soluble metals eluted from the wall of Ni/Fe-based alloy in high temperature water were observed. Results showed that metals could be eluted even at a short contact time. The presence of air also promotes elution at sub-critical conditions. At sub-critical conditions, a significant amount of Cr was extracted from SUS 316, while only traces of Ni, Fe, Mo and Mn were eluted. In contrast, Ni was removed in significant amounts compared to Cr when Inconel 625 was tested. It was observed that eluted metals tend to increased under acidic conditions and most of those metals were over the limit of WHO guideline for drinking water. The results are significant both on the viewpoint of environmental regulation on disposal of wastes containing heavy metals, toxicity of resulting product and catalytic effect on a particular reaction.

Mechanical alloying of Hf and Fe powders

International Nuclear Information System (INIS)

Mendoza Zelis, L.; Crespo, E.; Creus, M.; Damonte, L.C.; Sanchez, F.H.; Punte, G.

1994-01-01

Pure crystalline Hf and Fe powders were mixed and milled under an argon atmosphere. The evolution of the system with milling time was followed with Moessbauer effect spectroscopy and X-ray diffraction. The results indicate that in the first stages an amorphous Fe-rich alloy was gradually formed together with a solid solution of Hf in Fe beyond the solubility limit. (orig.)

The solubility of iron sulfides and their role in mass transport in Girdler-Sulfide heavy water plants

International Nuclear Information System (INIS)

Tewari, P.H.; Wallace, G.; Campbell, A.B.

1978-04-01

The solubilities of several iron sulfides, mackinawite FeSsub((1-x)), troilite FeS, pyrrhotite Fesub((1-x))S (monoclinic and hexagonal), and pyrite FeS 2 have been determined in aqueous H 2 S solution at 0.1 MPa and 1.8 MPa H 2 S pressures between 25 deg and 125 deg C. The dependence of solubility on the pH of the medium has also been studied. It is concluded that since mackinawite is the most soluble of the iron sulfides, and has the highest dissolution rate and the steepest decline in solubility with temperature, its prolonged formation during plant operation should be avoided to minimize iron transport from lower to higher temperature areas in Girdler-Sulfide (G.S.) heavy water plants. This can be achieved by a preconditioning of carbon steel surfaces to convert mackinawite to pyrrhotite and pyrite

Glucose, fructose and sucrose increase the solubility of protein-tannin complexes and at high concentration, glucose and sucrose interfere with bisulphite bleaching of wine pigments.

Science.gov (United States)

Harbertson, James F; Yuan, Chunlong; Mireles, Maria S; Hanlin, Rachel L; Downey, Mark O

2013-05-01

Wines were modified with increasing sugar concentrations and decreasing tannin concentrations and analysed by a combination of protein precipitation and bisulphite bleaching. Increasing sugar concentration decreased the precipitation of tannin and protein-precipitable polymeric pigments (PPP). The use of a hydrogen bond disruptor (urea) to reduce protein-tannin and protein-pigment complex formation showed that the effect of sugar concentration occurred by increasing the solubility of the tannin-protein complex, not by interfering with protein-tannin complex formation. By increasing the solubility of pigment-protein complexes, non-protein-precipitable polymeric pigments (nPPP) appeared to increase. There was also an increase in total polymeric pigments at each tannin concentration with increasing glucose and sucrose concentration, indicating that sugar concentration might also affect bisulphite bleaching of wine pigments. While a significant effect of sugar concentration on tannin-protein complex solubility was observed, these effects were greatest at sugar concentrations far in excess of normal wine making conditions. Under normal wine making conditions, sugar concentration will have a negligible effect on protein-precipitable tannin, PPP and nPPP concentrations. Copyright © 2012 Elsevier Ltd. All rights reserved.

Validation of a continuous flow method for the determination of soluble iron in atmospheric dust and volcanic ash.

Science.gov (United States)

Simonella, Lucio E; Gaiero, Diego M; Palomeque, Miriam E

2014-10-01

Iron is an essential micronutrient for phytoplankton growth and is supplied to the remote areas of the ocean mainly through atmospheric dust/ash. The amount of soluble Fe in dust/ash is a major source of uncertainty in modeling-Fe dissolution and deposition to the surface ocean. Currently in the literature, there exist almost as many different methods to estimate fractional solubility as researchers in the field, making it difficult to compare results between research groups. Also, an important constraint to evaluate Fe solubility in atmospheric dust is the limited mass of sample which is usually only available in micrograms to milligrams amounts. A continuous flow (CF) method that can be run with low mass of sediments (solubility studies on dust/ash. Copyright © 2014 Elsevier B.V. All rights reserved.

An unusual feature of uranium ore from Domiasiat, Meghalaya: presence of water soluble uranium

International Nuclear Information System (INIS)

Singh, A.K.; Padmanabhan, N.P.H.; Sivaramakrishnan, K.; Krishna Rao, N.

1993-01-01

An unusual feature of the recently discovered sandstone-type uranium deposit in Domiasiat is the presence of appreciable amount of water soluble uranium. With normal tap water at its natural pH (7.5-7.8), upto 35% of the uranium in the ore was found to be soluble during agitation in the different samples. Presence of other ions in appreciable quantities particularly SO 4 -2 Cl - and Fe +3 appear to influence the dissolution. Percolation experiments give terminal solubilization of upto 58%, but the instantaneous uranium concentration in the percolating water attains its maximum within the first few minutes of contact. A detailed study on the chemistry of uranium dissolution may throw light on the physico-chemical controls of localization of uranium in the deposit. (author). 7 refs., 3 tabs., 4 tabs

Concentration of Co2+, Fe3+ and Zn2+ ions with microbiological collectors

International Nuclear Information System (INIS)

Fisel, S.; Dulman, V.; Cecal, A.

1975-01-01

By means of the Spicaria Biolacea Abbott fungus a satisfactory microbiological concentration of 60 Co 2+ , sup(55+59)Fe 3+ and 65 Zn 2+ can be obtained under optimum experimental conditions. By repeating the cultures on the media obtained after filtration, multistage processes, and by adding the necessary nutritive substances, practically quantitative concentration of these three elements can be produced. The experimental results plead in favour of a concentration mechanism of the isotopes inside the cell with no surface adsorption. The influence of the experimental conditions i.e. pH, time and concentration have been investigated. (T.G.)

Uranyl Oxalate Solubility

Energy Technology Data Exchange (ETDEWEB)

Leturcq, G.; Costenoble, S.; Grandjean, S. [CEA Marcoule DEN/DRCP/SCPS/LCA - BP17171 - 30207 Bagnols sur Ceze cedex (France)

2008-07-01

The solubility of uranyl oxalate was determined at ambient temperature by precipitation in oxalic-nitric solutions, using an initial uranyl concentration of 0.1 mol/L. Oxalic concentration varied from 0.075 to 0.3 mol/L while nitric concentration ranged between 0.75 and 3 mol/L. Dissolution tests, using complementary oxalic-nitric media, were carried out for 550 hours in order to study the kinetic to reach thermodynamic equilibrium. Similar solubility values were reached by dissolution and precipitation. Using the results, it was possible to draw the solubility surface versus oxalic and nitric concentrations and to determine both the apparent solubility constant of UO{sub 2}C{sub 2}O{sub 4}, 3H{sub 2}O (Ks) and the apparent formation constant of the first uranyl-oxalate complex UO{sub 2}C{sub 2}O{sub 4} (log {beta}1), for ionic strengths varying between 1 and 3 mol/L. Ks and log {beta}1 values were found to vary from 1.9 10{sup -8} to 9.2 10{sup -9} and from 5.95 to 6.06, respectively, when ionic strength varied from 1 to 3 mol/L. A second model may fit our data obtained at an ionic strength of 3 mol/L suggesting as reported by Moskvin et al. (1959) that no complexes are formed for [H{sup +}] at 3 M. The Ks value would then be 1.3 10{sup -8}. (authors)

Monodisperse magnetite (Fe_3O_4) nanoparticles modified with water soluble polymers for the diagnosis of breast cancer by MRI method

International Nuclear Information System (INIS)

Rezayan, Ali Hossein; Mousavi, Majid; Kheirjou, Somayyeh; Amoabediny, Ghasem; Ardestani, Mehdi Shafiee; Mohammadnejad, Javad

2016-01-01

In this study, magnetic nanoparticles (MNPs) were synthesized via co-precipitation method. To enhance the biocompatibility and colloidal stability of the synthesized nanoparticles, they were modified with carboxyl functionalized PEG via dopamine (DPA) linker. Both modified and unmodified Fe_3O_4 nanoparticles exhibited super paramagnetic behavior (particle size below 20 nm). The saturation magnetization (Ms) of PEGdiacid-modified Fe_3O_4 was 45 emu/g, which was less than the unmodified Fe_3O_4 nanoparticles (70 emu/g). This difference indicated that PEGdiacid polymer was immobilized on the surface of Fe_3O_4 nanoparticles successfully. To evaluate the efficiency of the resulting nanoparticles as contrast agents for magnetic resonance imaging (MRI), different concentration of MNPs and different value of echo time TE were investigated. The results showed that by increasing the concentration of the nanoparticles, transverse relaxation time (T_2) decreased, which subsequently resulted in MR signal enhancement. T_2-weighted MR images of the different concentration of MNPs in different value of echo time TE indicated that MR signal intensity increased with increase in TE value up to 66 and then remained constant. The cytotoxicity effect of the modified and unmodified nanoparticles was evaluated in three different concentrations (12, 60 and 312 mg l"−"1) on MDA-MB-231 cancer cells for 24 and 48 h. In both tested time (24 and 48 h) for all three samples, the modified nanoparticles had long life time than unmodified nanoparticles. Cellular uptake of modified MNPs was 80% and reduced to 9% by the unmodified MNPs. - Highlights: • Magnetic nanoparticles (MNPs) were synthesized via co-precipitation method. • MNPs were modified with carboxyl functionalized PEG via dopamine (DPA) linker. • Modified and unmodified Fe_3O_4 nanoparticles exhibited super paramagnetic behavior. • T_2 decrease as MNPs concentration increase, this led to MR signal enhancement. • Modified

Pure Phase Solubility Limits: LANL

International Nuclear Information System (INIS)

C. Stockman

2001-01-01

The natural and engineered system at Yucca Mountain (YM) defines the site-specific conditions under which one must determine to what extent the engineered and the natural geochemical barriers will prevent the release of radioactive material from the repository. Most important mechanisms for retention or enhancement of radionuclide transport include precipitation or co-precipitation of radionuclide-bearing solid phases (solubility limits), complexation in solution, sorption onto surfaces, colloid formation, and diffusion. There may be many scenarios that could affect the near-field environment, creating chemical conditions more aggressive than the conditions presented by the unperturbed system (such as pH changes beyond the range of 6 to 9 or significant changes in the ionic strength of infiltrated waters). For an extended period of time, the near-field water composition may be quite different and more extreme in pH, ionic strength, and CO 2 partial pressure (or carbonate concentration) than waters at some distance from the repository. Reducing conditions, high pH (up to 11), and low carbonate concentration may be present in the near-field after reaction of infiltrating groundwater with engineered barrier systems, such as cementitious materials. In the far-field, conditions are controlled by the rock-mass buffer providing a near-neutral, oxidizing, low-ionic-strength environment that controls radionuclide solubility limits and sorption capacities. There is the need for characterization of variable chemical conditions that affect solubility, speciation, and sorption reactions. Modeling of the groundwater chemistry is required and leads to an understanding of solubility and speciation of the important radionuclides. Because experimental studies cannot be performed under the numerous potential chemical conditions, solubility limitations must rely on geochemical modeling of the radionuclide's chemistry. Fundamental thermodynamic properties, such as solubility products

Pure Phase Solubility Limits: LANL

Energy Technology Data Exchange (ETDEWEB)

C. Stockman

2001-01-26

The natural and engineered system at Yucca Mountain (YM) defines the site-specific conditions under which one must determine to what extent the engineered and the natural geochemical barriers will prevent the release of radioactive material from the repository. Most important mechanisms for retention or enhancement of radionuclide transport include precipitation or co-precipitation of radionuclide-bearing solid phases (solubility limits), complexation in solution, sorption onto surfaces, colloid formation, and diffusion. There may be many scenarios that could affect the near-field environment, creating chemical conditions more aggressive than the conditions presented by the unperturbed system (such as pH changes beyond the range of 6 to 9 or significant changes in the ionic strength of infiltrated waters). For an extended period of time, the near-field water composition may be quite different and more extreme in pH, ionic strength, and CO{sub 2} partial pressure (or carbonate concentration) than waters at some distance from the repository. Reducing conditions, high pH (up to 11), and low carbonate concentration may be present in the near-field after reaction of infiltrating groundwater with engineered barrier systems, such as cementitious materials. In the far-field, conditions are controlled by the rock-mass buffer providing a near-neutral, oxidizing, low-ionic-strength environment that controls radionuclide solubility limits and sorption capacities. There is the need for characterization of variable chemical conditions that affect solubility, speciation, and sorption reactions. Modeling of the groundwater chemistry is required and leads to an understanding of solubility and speciation of the important radionuclides. Because experimental studies cannot be performed under the numerous potential chemical conditions, solubility limitations must rely on geochemical modeling of the radionuclide's chemistry. Fundamental thermodynamic properties, such as solubility

Solubility behavior of narcotic analgesics in aqueous media: solubilities and dissociation constants of morphine, fentanyl, and sufentanil.

Science.gov (United States)

Roy, S D; Flynn, G L

1989-02-01

The pH dependence of the aqueous solubility of morphine, fentanyl, and sufentanil was investigated at 35 degrees C. Dissociation constants and corresponding pKa' values of the drugs were obtained from measured free-base solubilities (determined at high pH's) and the concentrations of saturated solutions at intermediate pH's. Morphine, fentanyl, and sufentanil exhibited pKa' values of 8.08, 8.99, and 8.51, respectively. Over the pH range of 5 to 12.5 the apparent solubilities are determined by the intrinsic solubility of the free base plus the concentration of ionized drug necessary to satisfy the dissociation equilibrium at a given pH. Consequently, the drug concentrations of saturated aqueous solutions fall off precipitously as the pH is raised and ionization is suppressed. Further, at low pH's the aqueous solubility of morphine increased in a linear fashion with increases in the molar strength of citric acid which was added to acidify the medium, suggesting the formation of a soluble morphine-citrate complex.

CEMS Investigations of Fe-Silicide Phases Formed by the Method of Concentration Controlled Phase Selection

Energy Technology Data Exchange (ETDEWEB)

Moodley, M. K.; Bharuth-Ram, K. [University of Durban-Westville, Physics Department (South Africa); Waal, H. de; Pretorius, R. [University of Stellenbosch, Physics Department (South Africa)

2002-03-15

Conversion electron Moessbauer spectroscopy (CEMS) measurements have been made on Fe-silicide samples formed using the method of concentration controlled phase selection. To prepare the samples a 10 nm layer of Fe{sub 30}M{sub 70} (M=Cr, Ni) was evaporated onto Si(100) surfaces, followed by evaporation of a 60 nm Fe layer. Diffusion of the Fe into the Si substrate and the formation of different Fe-Si phases was achieved by subjecting the evaporated samples to a series of heating stages, which consisted of (a) a 10 min anneal at 800 deg. C plus etch of the residual surface layer, (b) a further 3 hr anneal at 800 deg. C, (c) a 60 mJ excimer laser anneal to an energy density of 0.8 J/cm{sup 2}, and (d) a final 3 hr anneal at 800 deg. C. CEMS measurements were used to track the Fe-silicide phases formed. The CEMS spectra consisted of doublets which, based on established hyperfine parameters, could be assigned to {alpha}- or {beta}-FeSi{sub 2} or cubic FeSi. The spectra showed that {beta}-FeSi{sub 2} had formed already at the first annealing stage. Excimer laser annealing resulted in the formation of a phase with hyperfine parameters consistent with those of {alpha}-FeSi{sub 2}. A further 3 hr anneal at 800 deg. C resulted in complete reversal to the semiconducting {beta}-FeSi{sub 2} phase.

The system Fe-Os-S at 1180°, 1100°and 900°C

DEFF Research Database (Denmark)

Karup-Møller, Sven; Makovicky, E.

2002-01-01

Phase relations in the condensed system Fe-Os-S were investigated by means of dry syntheses from the elements at 1180degrees, 1100degrees and 900degreesC. The Fe-rich sulfide melt dissolves only traces of Os. Fe1-xS dissolves up to 0.7 at.% Os at 1180degreesC; Os solubility decreases to 0.3 at...... partition coefficients for Os. The three-phase association alloy-FeS1-xS-OsS2 involves alloys with less than 1 at.% Fe. The solubility of Fe in OsS2 increases with decreasing temperature and increasing fugacity of sulfur, possibly making analyses of erlichmanite for trace quantities of Fe important....

Influence of oxygen on the thermal behavior of the ZrO2-Fe2O3 system

International Nuclear Information System (INIS)

Stefanic, G.; Grzeta, B.; Music, S.

2000-01-01

Amorphous precursors of the ZrO 2 -Fe 2 O 3 system at the ZrO 2 -rich side of the concentration range were prepared by co-precipitation of the corresponding nitrates from aqueous solutions. The thermal behavior of the amorphous samples obtained was investigated using differential thermal analysis. It was found that amorphous precursors with Fe 2 O 3 content up to 30 mol% are single co-gels. In situ phase development during the calcination of the samples at low air pressure (∝4 x 10 -3 Pa) was investigated using X-ray diffraction at high temperature. The results were compared with the results of phase analysis after calcination and cooling in the presence of air at atmospheric pressure (∝10 5 Pa). The phase compositions of the samples at room temperature were determined using X-ray diffraction and laser Raman spectroscopy. The incorporation of Fe 3+ cations partially stabilized cubic ZrO 2 during the calcination in the presence of air at atmospheric pressure, but destabilized this polymorph during calcination at very low pressure. The observed differences in the phase development were attributed to the influence of oxygen vacancies introduced during calcination at very low pressure. The solubility of Fe 2 O 3 in ZrO 2 also depended on the calcination procedure. During calcination at atmospheric pressure, the solubility limits of Fe 2 O 3 in ZrO 2 decreased from more than 30 mol% at 600 C to ∝2 mol% at 1100 C. On the other hand, the solubility of Fe 2 O 3 in ZrO 2 was shown to be significantly higher during calcination at up to 1200 C at very low pressure. (orig.)

The effect of different concentrations of water soluble azadirachtin (neem metabolite) on Streptococcus mutans compared with chlorhexidine.

Science.gov (United States)

Kankariya, Amit R; Patel, Alok R; Kunte, Sanket S

2016-01-01

Despite advances in the development of anticaries chemotherapy, the newer agents are unable to control the initiation of dental caries. Research and development of natural antibacterial agents that are safe for the host as well as specific for oral pathogens is awaited. Neem tree extracts have been used for thousands of years for maintaining overall well-being. Chewing neem sticks in the morning is the most common indigenous method of cleaning the mouth in rural population. This has generated the interest of the dentists for the use of neem for controlling dental diseases. This study aims to evaluate the quantitative and qualitative effect of different concentrations of water soluble azadirachtin (neem metabolite) on Streptococcus mutans (S. mutans) against chlorhexidine. Plaque was collected from 30 children aged 8-12 years reporting to the Department of Pediatric and Preventive Dentistry, Bharti Vidyapeeth Dental College, Pune and transported to the laboratory. After incubation of the plates the inhibitory zones were noted and the diameter of the zone of inhibition was measured and recorded to check the inhibition of growth of S. mutans. For testing the bacterial survival, the biofilms were prepared and colony forming units (CFU) was enumerated using a digital colony counter. Two-way analysis of variance (ANOVA) and Tukey's test. The results show that there was no statistically significant difference in the inhibition of S. mutans between 40% concentration of water soluble azadirachtin and chlorhexidine. This study concluded that 40% water soluble azadirachtin is as effective as 0.2% chlorhexidine mouthrinse in reducing the S. mutans count in dental plaque. Hence, a water soluble formulation of azadirachtin may provide the maximum benefit to mankind to prevent dental caries.

Inflammatory reactions in placental blood of Plasmodium falciparum-infected women and high concentrations of soluble E-selectin and a circulating P. falciparum protein in the cord sera

DEFF Research Database (Denmark)

Jakobsen, P H; Rasheed, F N; Bulmer, J N

1998-01-01

concentrations measured in the placenta. Markers of inflammatory reactions: IL-10, sIL-2R, sIL-4R, and soluble tumour necrosis factor receptor I (sTNF-RI) were found in high concentrations in the placenta, indicating that inflammatory reactions take place in the placenta which has been regarded...... as an immunoprivileged site. Concentrations of soluble vascular cell adhesion molecule-1 (sVCAM-1) and soluble intracellular adhesion molecule-1 (sICAM-1), potential adhesion receptors for malaria parasites, were associated with an active P. falciparum infection in the placenta although the associations did not reach...

Wheat germ cell-free expression: Two detergents with a low critical micelle concentration allow for production of soluble HCV membrane proteins.

Science.gov (United States)

Fogeron, Marie-Laure; Badillo, Aurélie; Jirasko, Vlastimil; Gouttenoire, Jérôme; Paul, David; Lancien, Loick; Moradpour, Darius; Bartenschlager, Ralf; Meier, Beat H; Penin, François; Böckmann, Anja

2015-01-01

Membrane proteins are notoriously difficult to express in a soluble form. Here, we use wheat germ cell-free expression in the presence of various detergents to produce the non-structural membrane proteins 2, 4B and 5A of the hepatitis C virus (HCV). We show that lauryl maltose neopentyl glycol (MNG-3) and dodecyl octaethylene glycol ether (C12E8) detergents can yield essentially soluble membrane proteins at detergent concentrations that do not inhibit the cell-free reaction. This finding can be explained by the low critical micelle concentration (CMC) of these detergents, which keeps the monomer concentrations low while at the same time providing the necessary excess of detergent concentration above CMC required for full target protein solubilization. We estimate that a tenfold excess of detergent micelles with respect to the protein concentration is sufficient for solubilization, a number that we propose as a guideline for detergent screening assays. Copyright © 2014 Elsevier Inc. All rights reserved.

Voltammetry of Organic Pollutants on FeOOH Nanorods

International Nuclear Information System (INIS)

Zhang, Yuanyuan; Wan, Qijin; Yang, Nianjun

2017-01-01

FeOOH nanorods synthesized using a solvothermal approach have been employed to investigate the electrochemistry of organic pollutions, including ponceau 4R (PR), sunset yellow (SY), and tetrabromobisphenol A (TBBPA). The as-prepared FeOOH nanorods have been characterized using scanning electron microscopes (SEM), transmission electron microscope (TEM), X-ray photoelectron spectrometry, Brunauer-Emmett-Teller measurements, and electrochemical techniques. The modified electrode based on FeOOH nanorods exhibits a porous and net-like structure, resulting in a high surface area and many reactive/adsorption sites for soluble compounds. On this modified electrode, fast electron transfer processes of redox probes have been achieved. Electrochemistry of PR, SY, and TBBPA has been studied in detail using voltammetry, impedance, and chronocoulometry. The sensitive monitoring of both individual and total concentrations of three organic pollutions has been realized. The detection limits are 0.2, 1.0, and 0.55 nM for PR, SY, and TBBPA, respectively. Such an electrode is then promising for the electrochemical investigation and analysis of organic pollutions in different environments.

Structural, dielectric and magnetic properties of SnO{sub 2}-CuFe{sub 2}O{sub 4} nanocomposites

Energy Technology Data Exchange (ETDEWEB)

Ali, Kashif [Department of Physics, International Islamic University, Islamabad (Pakistan); Iqbal, Javed, E-mail: javed.saggu@qau.edu.pk [Laboratory of Nanoscience and Technology (LNT), Department of Physics, Qaid-i-Azam University, Islamabad (Pakistan); Jan, Tariq [Department of Physics, University of Lahore, Sargodha Campus, Sargodha (Pakistan); Wan, Dongyun [School of Materials Science and Engineering, Shanghai University, Shanghai 200444 (China); Ahmad, Naeem [Department of Physics, International Islamic University, Islamabad (Pakistan); Ahamd, Ishaq [Experimental Physics Labs, National Center for Physics, Islamabad (Pakistan); Ilyas, Syed Zafar [Department of Physics, Allama Iqbal Open University, Islamabad (Pakistan)

2017-04-15

The nanocomposites of (SnO{sub 2}){sub x}(CuFe{sub 2}O{sub 4}){sub (1−x)} (where x=0–100 wt%) have been successfully synthesized via two steps chemical method. XRD pattern has revealed the formation of inverse spinal phases with tetragonal crystal structure without any impurity phases for CuFe{sub 2}O{sub 4} sample. The thermodynamic solubility limit of SnO{sub 2} in CuFe{sub 2}O{sub 4} matrix has been found to be 30 wt% and above this percentage crystal phases related to SnO{sub 2} started to appear. The average particle size and shape of CuFe{sub 2}O{sub 4} nanoparticles have been strongly influenced by addition of SnO{sub 2} as depicted by TEM results. FTIR results have confirmed the existence of cation vibration bands at tetrahedral and octahedral sites along with Sn-O vibration band at higher concentrations, which also validates the formation of nanocomposites. Furthermore, the dielectric constant, tangent loss and conductivity of CuFe{sub 2}O{sub 4} nanoparticles have been found to increase up to 30 wt% addition of SnO{sub 2} and then decreases with further increase which is attributed to variations in resistivity and space charge carriers. Magnetic measurements have shown that saturation magnetization decreases from 35.68 emu/gm to 10.26 emu/gm with the addition of SnO{sub 2} content. - Highlights: • SnO{sub 2}-CuFe{sub 2}O{sub 4} nanocomposites with varying SnO{sub 2} concentrations were synthesized. • The thermodynamic solubility limit for SnO{sub 2} into CuFe{sub 2}O{sub 4} matrix by employing current method was found to be ≤30 wt%. • At higher concentrations, structural phases related to SnO{sub 2} started to appear. • FTIR results corroborated well with the XRD results. • It has been observed that the addition of SnO{sub 2} significantly influence the morphology, dielectric and magnetic properties of CuFe{sub 2}O{sub 4} nanoparticles.

Compression of Fe-Si-H alloys

Science.gov (United States)

Tagawa, S.; Ohta, K.; Hirose, K.

2014-12-01

The light elements in the Earth's core have not been fully identified yet, but hydrogen is now collecting more attention in part because recent planet formation theory suggests that large amount of water should have been brought to the Earth during its formation (giant-impact stage). Nevertheless, the effect of hydrogen on the property of iron alloys is little known so far. The earlier experimental study by Hirao et al. [2004 GRL] examined the compression behavior of dhcp FeHx (x ≈ 1) and found that it becomes much stiffer than pure iron above 50 GPa, where magnetization disappears. Here we examined the solubility of hydrogen into iron-rich Fe-Si alloys and the compression behavior of dhcp Fe-Si-H alloy at room temperature. Fe+6.5wt.%Si or Fe+9wt.%Si foil was loaded into a diamond-anvil cell (DAC), and then liquid hydrogen was introduced at temperatures below 20 K. X-ray diffraction measurements at SPring-8 revealed the formation of a dhcp phase with or without thermal annealing by laser above 8.4 GPa. The concentration of hydrogen in such dhcp lattice was calculated following the formula reported by Fukai [1992]; y = 0.5 and 0.2 for Fe-6.5wt.%Si-H or Fe-9wt.%Si-H alloys, respectively when y is defined as Fe(1-x)SixHy. Unlike Fe-H alloy, hydrogen didn't fully occupy the octahedral sites even under hydrogen-saturated conditions in the case of Fe-Si-H system. Anomaly was observed in obtained pressure-volume curve around 44 Å3 of unit-cell volume for both Fe-6.5wt.%Si-H and Fe-9wt.%Si-H alloys, which may be related to the spin transition in the dhcp phase. They became slightly stiffer at higher pressures, but their compressibility was still similar to that of pure iron.

Solubility limited radionuclide transport through geologic media

International Nuclear Information System (INIS)

Muraoka, Susumu; Iwamoto, Fumio; Pigford, T.H.

1980-11-01

Prior analyses for the migration of radionuclides neglect solubility limits of resolved radionuclide in geologic media. But actually some of the actinides may appear in chemical forms of very low solubility. In the present report we have proposed the migration model with no decay parents in which concentration of radionuclide is limited in concentration of solubility in ground water. In addition, the analytical solutions of the space-time-dependent concentration are presented in the case of step release, band release and exponential release. (author)

Formation and stability of Fe-rich precipitates in dilute Zr(Fe) single-crystal alloys

International Nuclear Information System (INIS)

Zou, H.; Hood, G.M.; Roy, J.A.; Schultz, R.J.

1993-02-01

The formation and stability of Fe-rich precipitates in two α-Zr(Fe) single-crystal alloys with nominal compositions (I, 50 ppma Fe, and II, 650 ppma Fe) have been investigated (the maximum solid solubility of Fe in α-Zr is 180 ppma - 800 C). Optical microscopy, scanning electron microscopy (SEM) and transmission electron microscopy (TEM) have been used to examine the characteristics of Fe-rich precipitates. SEM and TEM micrographs show that in as-grown alloy II, Zr 2 Fe precipitates are located at 'stringers'. Precipitates were not observed in as-grown alloy I. During annealing, below the solvus, Fe diffuses to the surfaces to form Zr 3 Fe precipitates in both alloys. The precipitates on the surfaces of alloy I tend to be star-like (0001) or pyramidal (1010), and their distribution is heterogeneous. Dissolution of Zr 3 Fe surface precipitates of alloy I (annealing above the solvus) leaves precipitate-like features on the surfaces. Zr 2 Fe precipitates in as-grown alloy II can be dissolved only by β-phase annealing. (Author) 8 figs., 18 refs

The influence of Fe2+ concentration and deposition time on the corrosion resistance of the electrodeposited zinc–nickel–iron alloys

Directory of Open Access Journals (Sweden)

M.M. Abou-Krisha

2016-11-01

Full Text Available Electrodeposition operating conditions for Zn–Ni–Fe alloys from sulfate baths and the corrosion resistance of the electrodeposited alloys were studied. The comparison between Zn–Ni and Zn–Ni–Fe alloys co-deposition revealed that the remarkable inhibition of Ni and Fe deposition takes place due to the presence of Zn2+ in the plating bath. The electrodeposition was performed on the steel substrate, under galvanostatic conditions, for varying Fe2+ bath concentrations and at different times. X-ray diffraction studies of the deposit showed the presence of Fe3Ni2 phase and γ-phase with a composition of Ni2Zn11. The obtained data also exposed that the corrosion resistance increases as a result of increasing Fe2+ concentration and deposition time. Investigation was carried out using cyclic voltammetry and galvastatic techniques for electrodeposition, while linear polarization resistance and anodic linear sweeping voltammetry techniques were used for corrosion study.

Microbial reduction of Fe(III) in the presence of oxygen under low pH conditions

Energy Technology Data Exchange (ETDEWEB)

Kusel, K.; Roth, U.; Drake, H.L. [University of Bayreuth, Bayreuth (Germany)

2002-07-01

In acidic, coal mining lake sediments, facultatively anaerobic Acidiphilium species are probably involved in the reduction of Fe(III). Previous results indicate that these bacteria can co-respire O{sub 2} and Fe(III). In this study, we investigated the capacity of the sediment microbiota to reduce Fe(III) in the presence of O{sub 2} at pH 3. In sediment microcosms with 4% O{sub 2} in the headspace, the concentration of Fe(II) increased at a rate of 1.03 {mu}mol (g wet sediment){sup -1} day{sup -1} within the first 7 days of incubation which was similar to the rate obtained with controls incubated under anoxic conditions. However, in microcosms incubated under air, Fe(II) was consumed after a lag phase of 8 h with a rate of 2.66 {mu}mol (g wet sediment){sup -1} day{sup -1}. Acidiphilium cryptum JF-5, isolated from this sediment, reduced soluble Fe(III) with either 4 or 21% O{sub 2} in the headspace, and concomitantly consumed O{sub 2}. However, the rate of Fe(II) formation normalized for cell density decreased under oxic conditions. Schwertmannite, the predominant Fe(III)-mineral of this sediment, was also reduced by A. cryptum JF-5 under oxic conditions. The rate of Fe(II) formation by A. cryptum JF-5 decreased after transfer from preincubation under air in medium lacking Fe(III). Acidiphilium cryptum JF-5 did not form Fe(II) when preincubated under air and transferred to anoxic medium containing Fe(III) and chloramphenicol, an inhibitor of protein synthesis. These results indicate that: (i) the reduction of Fe(III) can occur at low O{sub 2} concentrations in acidic sediments; (ii) Fe(II) can be oxidized at O{sub 2} concentrations near saturation; and (iii) the enzyme(s) responsible for the reduction of Fe(III) in A. cryptum JF-5 are not constitutive.

Evolution of Fe based intermetallic phases in Al–Si hypoeutectic casting alloys: Influence of the Si and Fe concentrations, and solidification rate

International Nuclear Information System (INIS)

Gorny, Anton; Manickaraj, Jeyakumar; Cai, Zhonghou; Shankar, Sumanth

2013-01-01

Highlights: •Anomalous evolution of Fe based intermetallic phases in Al–Si–Fe alloys. •XRF coupled with nano-diffraction to confirm the nano-size Fe intermetallic phases. •Crystallography of the θ-Al 13 Fe 4 , τ 5 -Al 8 Fe 2 Si and τ 6 -Al 9 Fe 2 Si 2 phases. •Peritectic reactions involving the Fe intermetallic phases in Al–Si–Fe alloys. -- Abstract: Al–Si–Fe hypoeutectic cast alloy system is very complex and reported to produce numerous Fe based intermetallic phases in conjunction with Al and Si. This publication will address the anomalies of phase evolution in the Al–Si–Fe hypoeutectic casting alloy system; the anomaly lies in the peculiarities in the evolution and nature of the intermetallic phases when compared to the thermodynamic phase diagram predictions and past publications of the same. The influence of the following parameters, in various combinations, on the evolution and nature of the intermetallic phases were analyzed and reported: concentration of Si between 2 and 12.6 wt%, Fe between 0.05 and 0.5 wt% and solidification rates of 0.1, 1, 5 and 50 K s −1 . Two intermetallic phases are observed to evolve in these alloys under these solidification conditions: the τ 5 -Al 8 SiFe 2 and τ 6 -Al 9 Fe 2 Si 2 . The τ 5 -Al 8 SiFe 2 phase evolves at all levels of the parameters during solidification and subsequently transforms into the τ 6 -Al 9 Fe 2 Si 2 through a peritectic reaction when promoted by certain combinations of solidification parameters such as higher Fe level, lower Si level and slower solidification rates. Further, it is also hypothesized from experimental evidences that the θ-Al 13 Fe 4 binary phase precludes the evolution of the τ 5 during solidification and subsequently transforms into the τ 6 phase during solidification. These observations are anomalous to the publications as prior art and simulation predictions of thermodynamic phase diagrams of these alloys, wherein, only one intermetallic phases in the �

The effect of different concentrations of water soluble azadirachtin (neem metabolite on Streptococcus mutans compared with chlorhexidine

Directory of Open Access Journals (Sweden)

Amit R Kankariya

2016-01-01

Full Text Available Despite advances in the development of anticaries chemotherapy, the newer agents are unable to control the initiation of dental caries. Research and development of natural antibacterial agents that are safe for the host as well as specific for oral pathogens is awaited. Neem tree extracts have been used for thousands of years for maintaining overall well-being. Chewing neem sticks in the morning is the most common indigenous method of cleaning the mouth in rural population. This has generated the interest of the dentists for the use of neem for controlling dental diseases. Aims: This study aims to evaluate the quantitative and qualitative effect of different concentrations of water soluble azadirachtin (neem metabolite on Streptococcus mutans (S. mutans against chlorhexidine. Materials and Methods: Plaque was collected from 30 children aged 8-12 years reporting to the Department of Pediatric and Preventive Dentistry, Bharti Vidyapeeth Dental College, Pune and transported to the laboratory. After incubation of the plates the inhibitory zones were noted and the diameter of the zone of inhibition was measured and recorded to check the inhibition of growth of S. mutans. For testing the bacterial survival, the biofilms were prepared and colony forming units (CFU was enumerated using a digital colony counter. Statistical Analysis Used: Two-way analysis of variance (ANOVA and Tukey′s test. Results: The results show that there was no statistically significant difference in the inhibition of S. mutans between 40% concentration of water soluble azadirachtin and chlorhexidine. Conclusions: This study concluded that 40% water soluble azadirachtin is as effective as 0.2% chlorhexidine mouthrinse in reducing the S. mutans count in dental plaque. Hence, a water soluble formulation of azadirachtin may provide the maximum benefit to mankind to prevent dental caries.

Comparative concentration analysis of Cr and Co in FeSi2 films performed by ERDA and RBS

International Nuclear Information System (INIS)

Bohne, W.; Reinsperger, G.-U.; Roehrich, J.; Roeschert, G.; Selle, B.; Stauss, P.

2000-01-01

Thin films of β-FeSi 2 doped by Co or Cr were grown on Si substrates by molecular beam epitaxy (MBE) using three separately controlled evaporation sources. The dopant concentration was measured concurrently by heavy-ion ERDA with 129 Xe ions of 140-250 MeV, by heavy-ion RBS with 15 MeV 14 N and by standard RBS with 1.4 MeV 4 He ions. Among these techniques, the TOF-ERDA was most powerful in providing a high mass resolution and a low detection limit for Co and Cr (∼0.1 at.%). Because of the complete overlap of the dopant signals with the Fe signal the standard RBS spectra were evaluated by relying on the differences between the scattering cross-sections from the dopant atoms and Fe. This approach proved to be applicable as far as the dopants had a constant depth profile with sufficiently high concentration. For Cr concentrations exceeding the miscibility limit the RBS results deviate significantly from those of ERDA due to increasing dopant depth inhomogeneities

Solubility of pllutonium in alkaline salt solutions

International Nuclear Information System (INIS)

Hobbs, D.T.; Edwards, T.B.

1993-01-01

Plutonium solubility data from several studies have been evaluated. For each data set, a predictive model has been developed where appropriate. In addition, a statistical model and corresponding prediction intervals for plutonium solubility as a quadratic function of the hydroxide concentration have been developed. Because of the wide range of solution compositions, the solubility of plutonium can vary by as much as three orders of magnitude for any given hydroxide concentration and still remain within the prediction interval. Any nuclear safety assessments that depend on the maximum amount of plutonium dissolved in alkaline salt solutions should use concentrations at least as great as the upper prediction limits developed in this study. To increase the confidence in the prediction model, it is recommended that additional solubility tests be conducted at low hydroxide concentrations and with all of the other solution components involved. To validate the model for application to actual waste solutions, it is recommended that the plutonium solubilities in actual waste solutions be determined and compared to the values predicted by the quadratic model

Influencing the solubility of oxalates for the preparation of ceramic powders from mixed precipitates

International Nuclear Information System (INIS)

Krueger, C.; Fischer, S.; Fischer, St.; Chebani, M.Kh.

1991-01-01

Based on investigations of the solubility of oxalate with 140 Ba, 64 Cu and 59 Fe, techniques for quantitative oxalate coprecipitation were developed. Addition of organic solvents lowers the solubility and leads to a smaller particle size of products. (orig.) [de

Bioavailability of organically bound Fe to model phytoplankton of the Southern Ocean

Directory of Open Access Journals (Sweden)

C. S. Hassler

2009-10-01

Full Text Available Iron (Fe is known to be mostly bound to organic ligands and to limit primary productivity in the Southern Ocean. It is thus important to investigate the bioavailability of organically bound Fe. In this study, we used four phytoplankton species of the Southern Ocean (Phaeocystis sp., Chaetoceros sp., Fragilariopsis kerguelensis and Thalassiosira antarctica Comber to measure the influence of various organic ligands on Fe solubility and bioavailability. Short-term uptake Fe:C ratios were inversely related to the surface area to volume ratios of the phytoplankton. The ratio of extracellular to intracellular Fe is used to discuss the relative importance of diffusive supply and uptake to control Fe bioavailability. The effect of excess organic ligands on Fe bioavailability cannot be solely explained by their effect on Fe solubility. For most strains studied, the bioavailability of Fe can be enhanced relative to inorganic Fe in the presence of porphyrin, catecholate siderophore and saccharides whereas it was decreased in presence of hydroxamate siderophore and organic amine. For Thalassiosira, iron bioavailability was not affected by the presence of porphyrin, catecholate siderophore and saccharides. The enhancement of Fe bioavailability in presence of saccharides is presented as the result from both the formation of bioavailable (or chemically labile organic form of Fe and the stabilisation of Fe within the dissolved phase. Given the ubiquitous presence of saccharides in the ocean, these compounds might represent an important factor to control the basal level of soluble and bioavailable Fe. Results show that the use of model phytoplankton is promising to improve mechanistic understanding of Fe bioavailability and primary productivity in HNLC regions of the ocean.

Intercrystalline internal adsorption in systems with limiting solubility of components

International Nuclear Information System (INIS)

Krysova, S.K.; Stepanova, V.A.; Mozgovoj, M.V.

1979-01-01

The decrease of the excessive energy of the intercrystalline boundary of ion by additions of transitional elements having unlimited solubility in iron has been studied. The data obtained agree with the results of an earlier work based on materials of a less higher initial purity. For the systems studied (Fe-V, Fe-Cr, Fe-Mn, Fe-Ni) the degree of the intercrystalline interval adsorption is independent of either the annealing temperature or the cooling method. This corresponds to the notion of the relationship between the intercrystalline internal adsorption and the cubic solubility of the addition in a given solvent. For pure ion, a weak temperature dependence of the excessive energy of the intercrystalline boundries was found in the lower section of the examined temperature range. The constants of cumulative recrystallization of the alloys studied in α-phase show a stepwise dependence upon the atomic number of the solute component, what indicates the relationship between the cumulative recrystallization and the intercrystalline internal adsorption. A monotonous decrease of the constant of cumulative recrystallization is observed for the same alloys in α-phase, on both sides of iron

Synthesis of nano-TiO2 photocatalysts with tunable Fe doping concentration from Ti-bearing tailings

Science.gov (United States)

Sui, Yulei; Liu, Qingxia; Jiang, Tao; Guo, Yufeng

2018-01-01

In this work, highly pure nano-TiO2 photocatalysts with varying Fe doping concentration were successfully synthesized from low-cost Ti-bearing tailings by an acidolysis-hydrothermal route. The effects of H2SO4 concentration, leaching temperature, acid/tailings ratio and leaching time on the recovery of TiO2 from the tailings were investigated. Synthesized samples were characterized by XRD, TEM, EDS, XPS, and UV-vis spectroscopy. The results showed that the material prepared is characteristic anatase with the average size of 20 nm and the Fe doping concentration in the synthesized nano-TiO2 is tunable. The photocatalytic activity of synthesized nano-TiO2 photocatalyst was also evaluated by the photodegradation of Rhodamine B under visible light and UV light irradiation. Our study demonstrates a low-cost approach to synthesize highly efficient and visible light responsive catalysts.

Thermodynamic assessment of the La-Fe-O system

DEFF Research Database (Denmark)

Povoden-Karadeniz, E.; Grundy, A.N.; Chen, Ming

2009-01-01

The La-Fe and the La-Fe-O systems are assessed using the Calphad approach, and the Gibbs energy functions of ternary oxides are presented. Oxygen and mutual La and Fe solubilities in body-centered cubic (bcc) and face-centered cubic (fcc) structured metallic phases are considered in the modeling......-sublattice model for ionic liquids. The calculated La-Fe phase diagram, LaO1.5-FeO x phase diagrams at different oxygen partial pressures, and phase equilibria of the La-Fe-O system at 873, 1073, and 1273 K as a function of oxygen partial pressures are presented....

Study of iron solubility in aluminium and SAP-type materials by the method of nuclear gamma resonance

International Nuclear Information System (INIS)

Nechaev, Yu.S.; Edigarov, V.S.; Pustov, Yu.A.

1979-01-01

Presented are the results of studying equilibrium solubility of iron (FeAl 3 ) in aluminium crystals with a conventional density of dislocations (rhosub(perpendicular) approximately 10 6 cm -2 ), and in crystals of the SAP type with rhosub(perpendicular) approximately 10 9 cm -2 . The method of gamma-resonance spectroscopy, chemical analysis were used as well as measurements of residual electric resistivity. Changes in entropy and enthalpy are determined while dissolving a FeAl 3 mole in aluminium lattice. The analysis of the data obtained allows one to suppose the presence of regions with high local concentrations of iron atoms near dislocations, the atoms being in two different states which provide respectively a doublet and a singlet in the Moessbauer spectrum

Interaction between U(VI) and Fe(II) in aqueous solution under anaerobic conditions. Closed system experiments

International Nuclear Information System (INIS)

Myllykylae, E.; Ollila, K.

2011-01-01

The aim of these experiments is to investigate the potential reduction of U(VI) carbonate and hydroxide complexes by aqueous Fe(II). This reduction phenomenon could be important under the disposal conditions of spent fuel. If groundwater enters the copper/iron canister, alpha radiolysis of the water may locally induce oxidizing conditions on the surface of UO 2 fuel, leading to the dissolution of UO 2 as more soluble U(VI) species. A potential reducing agent in the intruding water is Fe(II)(aq) from anaerobic corrosion of the copper/iron canister. The reduction of U(VI) to U(IV) would substantially decrease the solubility of U as well as co-precipitate other actinides and radionuclides. The interaction experiments were conducted in 0.01 M NaCl and 0.002 M NaHCO 3 solutions using an initial uranium concentration of either 8.4 x 10 -8 or 4.2 x 10 -7 mol/L with an initial Fe(II) concentration of 1.8 x 10 -6 in the NaCl solutions and 1.3 x 10 -6 mol/L in the NaHCO 3 solutions. Only after an equilibration period for U(VI) complexation was Fe(II) added to the solutions. The reaction times varied from 1 week to 5 months. For extra protection against O 2 , even inside a glove-box (N 2 atmosphere), the plastic reaction vessels were closed in metallic containers. The concentrations of U, Fe TOT and Fe(II) were analysed as a function of time for unfiltered, micro- and ultrafiltered samples. In addition, the precipitate on the ultrafilters was analysed with ESEM-EDS. The evolution of pH and Eh values was measured. The oxidation state of U in solution was preliminarily analysed for chosen periods. The results of the tests in 0.01 M NaCl showed an initial rapid decrease in U concentration after the addition of Fe(II) to the solution. The U found on test vessel walls at the end of the reaction periods, as well as the ESEM-EDS analyses of the filtered precipitates from the test solutions, showed that precipitation of U had occurred. The oxidation state analyses showed the presence

Improving the Representation of Soluble Iron in Climate Models

Energy Technology Data Exchange (ETDEWEB)

Perez Garcia-Pando, Carlos [Columbia Univ., New York, NY (United States)

2016-03-13

Mineral dust produced in the arid and semi-arid regions of the world is the dominant source of iron (Fe) in atmospheric aerosol inputs to the open ocean. The bioavailable Fe fraction of atmospheric dust is thought to regulate and occasionally limit the primary productivity in large oceanic regions, which influences the CO2 uptake from the atmosphere affecting the Earth’s climate. Because Fe bioavailability cannot be directly measured, it is assumed that the dissolved Fe or highly reactive Fe in the dust is bioavailable. The fraction of soluble Fe in dust is mainly controlled by: (1) the mineral composition of the soils and the emitted dust from the source areas; (2) the atmospheric processing that converts the Fe in Fe-bearing minerals into highly soluble forms of Fe. The project has mainly focused on constraining the mineral composition of dust aerosols (1), a previously neglected, yet a key issue to constrain the deposition of soluble iron. Deriving aerosol mineral composition requires global knowledge of the soil mineral content, which is available from poorly constrained global atlases. In addition, the mineral content of the emitted aerosol differs from that of the parent soil. Measurements of soil mineral fractions are based upon wet sedimentation (or ’wet sieving’) techniques that disturb the soil sample, breaking aggregates that are found in the original, undispersed soil that is subject to wind erosion. Wet sieving alters the soil size distribution, replacing aggregates that are potentially mobilized as aerosols with a collection of smaller particles. A major challenge is to derive the size-distributed mineral fractions of the emitted dust based upon their fractions measured from wet-sieved soils. Finally, representations of dust mineral composition need to account for mixtures of minerals. Examination of individual particles shows that iron, an element that is central to many climate processes, is often found as trace impurities of iron oxide

Evolution of Fe based intermetallic phases in Al–Si hypoeutectic casting alloys: Influence of the Si and Fe concentrations, and solidification rate

Energy Technology Data Exchange (ETDEWEB)

Gorny, Anton; Manickaraj, Jeyakumar [Light Metal Casting Research Centre (LMCRC), Department of Mechanical Engineering, McMaster University, 1280 Main Street W, Hamilton, ON, Canada L8S 4L7 (Canada); Cai, Zhonghou [Advanced Photon Source, Argonne National Laboratory, 9700 South Cass Avenue, Argonne, IL 60439 (United States); Shankar, Sumanth, E-mail: shankar@mcmaster.ca [Light Metal Casting Research Centre (LMCRC), Department of Mechanical Engineering, McMaster University, 1280 Main Street W, Hamilton, ON, Canada L8S 4L7 (Canada)

2013-11-15

Highlights: •Anomalous evolution of Fe based intermetallic phases in Al–Si–Fe alloys. •XRF coupled with nano-diffraction to confirm the nano-size Fe intermetallic phases. •Crystallography of the θ-Al{sub 13}Fe{sub 4}, τ{sub 5}-Al{sub 8}Fe{sub 2}Si and τ{sub 6}-Al{sub 9}Fe{sub 2}Si{sub 2} phases. •Peritectic reactions involving the Fe intermetallic phases in Al–Si–Fe alloys. -- Abstract: Al–Si–Fe hypoeutectic cast alloy system is very complex and reported to produce numerous Fe based intermetallic phases in conjunction with Al and Si. This publication will address the anomalies of phase evolution in the Al–Si–Fe hypoeutectic casting alloy system; the anomaly lies in the peculiarities in the evolution and nature of the intermetallic phases when compared to the thermodynamic phase diagram predictions and past publications of the same. The influence of the following parameters, in various combinations, on the evolution and nature of the intermetallic phases were analyzed and reported: concentration of Si between 2 and 12.6 wt%, Fe between 0.05 and 0.5 wt% and solidification rates of 0.1, 1, 5 and 50 K s{sup −1}. Two intermetallic phases are observed to evolve in these alloys under these solidification conditions: the τ{sub 5}-Al{sub 8}SiFe{sub 2} and τ{sub 6}-Al{sub 9}Fe{sub 2}Si{sub 2}. The τ{sub 5}-Al{sub 8}SiFe{sub 2} phase evolves at all levels of the parameters during solidification and subsequently transforms into the τ{sub 6}-Al{sub 9}Fe{sub 2}Si{sub 2} through a peritectic reaction when promoted by certain combinations of solidification parameters such as higher Fe level, lower Si level and slower solidification rates. Further, it is also hypothesized from experimental evidences that the θ-Al{sub 13}Fe{sub 4} binary phase precludes the evolution of the τ{sub 5} during solidification and subsequently transforms into the τ{sub 6} phase during solidification. These observations are anomalous to the publications as prior art and

Heavy metal (Cu, Cr, Zn, and Fe) concentration on coralreef in panjang island coastal, Jepara

International Nuclear Information System (INIS)

Heni Susiati; Yarianto SBS; Ali Arman L; Yulizon Menri

2008-01-01

Observation on the accumulation of Cu, Cr, Zn, and Fe heavy metals in coral tissue were carried out in Panjang island, Jepara by NAA method. The purpose of this research is to determine the concentration of heavy metals on coral reef tissue in order to update environmental data to support site licensing and Environmental Impact Assessment (EIA) of Nuclear Power Plants (NPP). The result indicated that the concentration of Zn is 1,78 - 42,34 ppm, Cu is undetected - 0,41 ppm, Cr is 0,03 - 0,35 ppm and Fe is 5,25 - 30,56 ppm. The data shows that the accumulation of heavy metals in the coral reef tissue is higher than environmental threshold value, especially for marine biota life referring to the Environmental Ministry Decree Number 51 year 2004. (author)

A Fe(II)/citrate/UV/PMS process for carbamazepine degradation at a very low Fe(II)/PMS ratio and neutral pH: The mechanisms.

Science.gov (United States)

Ling, Li; Zhang, Dapeng; Fan, Chihhao; Shang, Chii

2017-11-01

A novel Fe(II)/citrate/UV/PMS process for degrading a model micropollutant, carbamazepine (CBZ), at a low Fe(II)/PMS ratio and neutral pH has been proposed in this study, and the mechanisms of radical generation in the system was explored. With a UV dose of 302.4 mJ/cm 2 , an initial pH of 7, and CBZ, PMS, Fe(II) and citrate at initial concentrations of 10, 100, 12 and 26 μM, respectively, the CBZ degradation efficiency reached 71% in 20 min in the Fe(II)/citrate/UV/PMS process, which was 4.7 times higher than that in either the citrate/UV/PMS or Fe(II)/citrate/PMS process. The enhanced CBZ degradation in the Fe(II)/citrate/UV/PMS process was mainly attributed to the continuous activation of PMS by the UV-catalyzed regenerated Fe(II) from a Fe(III)-citrate complex, [Fe 3 O(cit) 3 H 3 ] 2- , which not only maintained Fe(III) soluble at neutral pH, but also increased 6.6 and 2.6 times of its molar absorbance and quantum yield as compared to those of ionic Fe(III), respectively. In the Fe(II)/citrate/UV/PMS process, the SO 4 •- produced from the fast reaction between PMS and the initially-added Fe(II) contributed 11% of CBZ degradation. The PMS activation by the UV radiation and regenerated Fe(II) contributed additional 14% and 46% of CBZ removal, respectively. The low iron and citrate doses and the fast radical generation at neutral pH make the Fe(II)/citrate/UV/PMS process suitable for degrading recalcitrant organic compounds in potable water. Copyright © 2017 Elsevier Ltd. All rights reserved.

Dietary fiber content influences soluble carbohydrate levels in ruminal fluids.

Science.gov (United States)

Pinder, R S; Patterson, J A; O'Bryan, C A; Crandall, P G; Ricke, S C

2012-01-01

The soluble carbohydrate concentration of ruminal fluid, as affected by dietary forage content (DFC) and/or ruminally undegradable intake protein content (UIPC), was determined. Four ruminally cannulated steers, in a 4 × 4 Latin square design, were offered diets containing high (75 % of DM) or low (25 % of DM) DFC and high (6 % of DM) or low (5 % of DM) UIPC, in a 2 × 2 factorial arrangement. Zinc-treated SBM was the primary UIP source. Soluble hexose concentration (145.1 μM) in ruminal fluid (RF) of steers fed low DFC diets exhibited a higher trend (P = 0.08) than that (124.5 μM) of steers fed high DFC diets. UIPC did not modulate (P = 0.54) ruminal soluble hexose concentrations. Regardless of diet, soluble hexose concentration declined immediately after feeding and did not rise until 3 h after feeding (P ruminal fluid could not be determined. However, unsubstituted xylose and arabinose were excluded. These data indicate that: (i) soluble carbohydrate concentrations remain in ruminal fluid during digestion and fermentation; (ii) slight diurnal changes began after feeding; (iii) DFC influences the soluble carbohydrate concentration in RF; and (iv) UIPC of these diets does not affect the soluble carbohydrate concentration of RF.

Survival of Anaerobic Fe2+ Stress Requires the ClpXP Protease.

Science.gov (United States)

Bennett, Brittany D; Redford, Kaitlyn E; Gralnick, Jeffrey A

2018-04-15

Shewanella oneidensis strain MR-1 is a versatile bacterium capable of respiring extracellular, insoluble ferric oxide minerals under anaerobic conditions. The respiration of iron minerals results in the production of soluble ferrous ions, which at high concentrations are toxic to living organisms. It is not fully understood how Fe 2+ is toxic to cells anaerobically, nor is it fully understood how S. oneidensis is able to resist high levels of Fe 2+ Here we describe the results of a transposon mutant screen and subsequent deletion of the genes clpX and clpP in S. oneidensis , which demonstrate that the protease ClpXP is required for anaerobic Fe 2+ resistance. Many cellular processes are known to be regulated by ClpXP, including entry into stationary phase, envelope stress response, and turnover of stalled ribosomes. However, none of these processes appears to be responsible for mediating anaerobic Fe 2+ resistance in S. oneidensis Protein trapping studies were performed to identify ClpXP targets in S. oneidensis under Fe 2+ stress, implicating a wide variety of protein targets. Escherichia coli strains lacking clpX or clpP also display increased sensitivity to Fe 2+ anaerobically, indicating Fe 2+ resistance may be a conserved role for the ClpXP protease system. Hypotheses regarding the potential role(s) of ClpXP during periods of high Fe 2+ are discussed. We speculate that metal-containing proteins are misfolded under conditions of high Fe 2+ and that the ClpXP protease system is necessary for their turnover. IMPORTANCE Prior to the evolution of cyanobacteria and oxygenic photosynthesis, life arose and flourished in iron-rich oceans. Today, aqueous iron-rich environments are less common, constrained to low-pH conditions and anaerobic systems such as stratified lakes and seas, digestive tracts, subsurface environments, and sediments. The latter two ecosystems often favor dissimilatory metal reduction, a process that produces soluble Fe 2+ from iron oxide minerals

Effects of organic matters coming from Chinese tea on soluble copper release from copper teapot

International Nuclear Information System (INIS)

Ni Lixiao; Li Shiyin

2008-01-01

The morphology and elemental composition of the corrosion products of copper teapot's inner-surface were characterized by the scanning electron microscopy and energy dispersive X-ray surface analysis (SEM/EDS), X-ray powder diffraction (XRD) and X-ray photon spectroscopy (XPS) analysis. It was revealed that Cu, Fe, Ca, P, Si and Al were the main elements of corrosion by-products, and the α-SiO 2 , Cu 2 O and CaCO 3 as the main mineral components on the inner-surface of copper teapot. The effects of organic matters coming from Chinese tea on soluble copper release from copper teapots in tap water were also investigated. The results showed that the doses of organic matter (as TOC), temperate and stagnation time have significant effects on the concentration of soluble copper released from copper teapots in tap water

Organic Fe speciation in the Eurasian Basins of the Arctic Ocean and its relation to terrestrial DOM

NARCIS (Netherlands)

Slagter, H.A.; Reader, H.E.; Rijkenberg, M.J.A.; Rutgers van der Loeff, M.; de Baar, H.J.W.; Gerringa, L.J.A.

2017-01-01

The bio-essential trace metal iron (Fe) has poor inorganic solubility in seawater, and therefore dissolution is dependent on organic complexation. The Arctic Ocean is subject to strong terrestrial influences which contribute to organic solubility of Fe, particularly in the surface. These influences

Soluble Non-ammonia Nitrogen in Ruminal and Omasal Digesta of Korean Native Steers Supplemented with Soluble Proteins

Directory of Open Access Journals (Sweden)

C. W. Choi

2012-09-01

Full Text Available An experiment was conducted to study the effect of soluble protein supplements on concentration of soluble non-ammonia nitrogen (SNAN in the liquid phase of ruminal (RD and omasal digesta (OD of Korean native steers, and to investigate diurnal pattern in SNAN concentration in RD and OD. Three ruminally cannulated Korean native steers in a 3×3 Latin square design consumed a basal diet of rice straw and corn-based concentrate (control, and that supplemented (kg/d DM basis with intact casein (0.24; IC or acid hydrolyzed casein (0.46; AHC. Ruminal digesta was sampled using a vacuum pump, whereas OD was collected using an omasal sampling system at 2.0 h intervals after a morning feeding. The SNAN fractions (free amino acid (AA, peptide and soluble protein in RD and OD were assessed using the ninhydrin assay. Concentrations of free AA and total SNAN in RD were significantly (p<0.05 lower than those in OD. Although free AA concentration was relatively high, mean peptide was quantitatively the most important fraction of total SNAN in both RD and OD, indicating that degradation of peptide to AA rather than hydrolysis of soluble protein to peptide or deamination may be the most limiting step in rumen proteolysis of Korean native steers. Diurnal variation in peptide concentration in OD for the soluble protein supplemented diets during the feeding cycle peaked 2 h post-feeding and decreased thereafter whereas that for the control was relatively constant during the entire feeding cycle. Diurnal variation in peptide concentration was rather similar between RD and OD.

The relationship between heavy metal concentration and soil mycoflora in the Gizan region, Saudi Arabia

OpenAIRE

Falih, A. M. [عبد الله مساعد خلف الفالح

1997-01-01

Soil samples were collected from different places from the Gizan region, Saudi Arabia, and analyzed mechanically and chemically for mineral content. The soils were highly alkaline and sandy in texture in all cases. The concentration of Zn, Pb and Cu were within the ranges reported earlier for some Saudi Arabian soils, while Fe, Co and Al occurred in high concentrations. There was a high content of total soluble salts in the samples tested. There was a marked decrease in bacterial counts, a...

Water-soluble dietary fibers and cardiovascular disease.

Science.gov (United States)

Theuwissen, Elke; Mensink, Ronald P

2008-05-23

One well-established way to reduce the risk of developing cardiovascular disease (CVD) is to lower serum LDL cholesterol levels by reducing saturated fat intake. However, the importance of other dietary approaches, such as increasing the intake of water-soluble dietary fibers is increasingly recognized. Well-controlled intervention studies have now shown that four major water-soluble fiber types-beta-glucan, psyllium, pectin and guar gum-effectively lower serum LDL cholesterol concentrations, without affecting HDL cholesterol or triacylglycerol concentrations. It is estimated that for each additional gram of water-soluble fiber in the diet serum total and LDL cholesterol concentrations decrease by -0.028 mmol/L and -0.029 mmol/L, respectively. Despite large differences in molecular structure, no major differences existed between the different types of water-soluble fiber, suggesting a common underlying mechanism. In this respect, it is most likely that water-soluble fibers lower the (re)absorption of in particular bile acids. As a result hepatic conversion of cholesterol into bile acids increases, which will ultimately lead to increased LDL uptake by the liver. Additionally, epidemiological studies suggest that a diet high in water-soluble fiber is inversely associated with the risk of CVD. These findings underlie current dietary recommendations to increase water-soluble fiber intake.

Decreased concentrations of soluble interleukin-1 receptor accessory protein levels in the peritoneal fluid of women with endometriosis.

Science.gov (United States)

Michaud, Nadège; Al-Akoum, Mahéra; Gagnon, Geneviève; Girard, Karine; Blanchet, Pierre; Rousseau, Julie Anne; Akoum, Ali

2011-12-01

Interleukin 1 (IL1) may play an important role in endometriosis-associated pelvic inflammation, and natural specific inhibitors, including soluble IL1 receptor accessory protein (sIL1RAcP) and soluble IL1 receptor type 2 (sIL1R2), are critical for counterbalancing the pleiotropic effects of IL1. The objective of this study was to evaluate the levels of sIL1RAcP, together with those of sIL1R2 and IL1β, in the peritoneal fluid of women with and without endometriosis. Peritoneal fluid samples were obtained at laparoscopy and assessed by ELISA. sIL1RAcP concentrations were reduced in endometriosis stages I-II and III-IV. sIL1R2 concentrations were decreased, and those of IL1β were significantly increased in endometriosis stages I-II. sIL1RAcP and sIL1R2 concentrations were significantly decreased in the secretory phase of the menstrual cycle, and IL1β concentrations were elevated in the proliferative and the secretory phases. sIL1RAcP and sIL1R2 concentrations were reduced in women with endometriosis who were infertile, fertile, suffering from pelvic pain or pain-free. However, IL1β concentrations were significantly reduced in women with endometriosis who were infertile or had pelvic pain. These changes may exacerbate the local peritoneal inflammatory reaction observed in women with endometriosis and contribute to endometriosis pathophysiology and the major symptoms of this disease. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

Synthesis, characterization and stability of Cr(III) and Fe(III) hydroxides

International Nuclear Information System (INIS)

Papassiopi, N.; Vaxevanidou, K.; Christou, C.; Karagianni, E.; Antipas, G.S.E.

2014-01-01

Highlights: • Fe(III)–Cr(III) hydroxides enhance groundwater quality better than pure Cr(III) compounds. • Crystalline Cr(OH) 3 ·3H 2 O was unstable, with a solubility higher than 50 μg/l. • Amorphous Cr(OH) 3 (am) was stable with a solubility lower than 50 μg/l in the range 5.7 0.75 Cr 0.25 (OH) 3 , the stability region was extended to 4.8 3 ·xH 2 O whereas in the presence of iron the precipitate is a mixed Fe (1−x) Cr x (OH) 3 phase. In this study, we report on the synthesis, characterisation and stability of mixed (Fe x ,Cr 1−x )(OH) 3 hydroxides as compared to the stability of Cr(OH) 3 . We established that the plain Cr(III) hydroxide, abiding to the approximate molecular formula Cr(OH) 3 ·3H 2 O, was crystalline, highly soluble, i.e. unstable, with a tendency to transform into the stable amorphous hydroxide Cr(OH) 3 (am) phase. Mixed Fe 0.75 Cr 0.25 (OH) 3 hydroxides were found to be of the ferrihydrite structure, Fe(OH) 3 , and we correlated their solubility to that of a solid solution formed by plain ferrihydrite and the amorphous Cr(III) hydroxide. Both our experimental results and thermodynamic calculations indicated that mixed Fe(III)–Cr(III) hydroxides are more effective enhancers of groundwater quality, in comparison to the plain amorphous or crystalline Cr(III) hydroxides, the latter found to have a solubility typically higher than 50 μg/l (maximum EU permitted Cr level in drinking water), while the amorphous Cr(OH) 3 (am) phase was within the drinking water threshold in the range 5.7 0.75 Cr 0.25 (OH) 3 hydroxides studied were of extended stability in the 4.8 < pH < 13.5 range

Contribution to the study of solid state diffusion in concentrated alloys - A case study of the Fe - Pd system

International Nuclear Information System (INIS)

Gomez Jaen, Juan Pedro

1973-01-01

The study of diffusion in concentrated alloys presents two main aspects: 1) The search for an adequate theoretical framework; 2) The carrying out of experiments with a view towards verification of the theory. From the theoretical standpoint it is shown that the atomic theory of diffusion, as formulated by MANNING, can be linked to the phenomenological theory of HOWARD and LIDIARD. Thus it is seen that the vacancy flow effect is really a cross correlation effect and, that the phenomenological ONSAGER coefficients can be expressed as functions of the correlation factors. From the experimental side, a number of experiments were performed on the Fe - Pd System, including experiments on interdiffusion, the KIRKENDALL effect, diffusion of Fe 59 and Pd 103 isotopes in homogeneous Fe - Pd alloys, and the diffusion of these isotopes in the concentration gradient. We introduce a perfected method for taking account of the changes in the molar volume of the alloy expressed as a function of the concentration, throughout the diffusion process. The experiments enabled us to obtain the different diffusion coefficients, correlation factors, and partial mobilities, thus allowing a precise knowledge of the Fe - Pd solid state diffusion system.(author) [fr

Monodisperse magnetite (Fe{sub 3}O{sub 4}) nanoparticles modified with water soluble polymers for the diagnosis of breast cancer by MRI method

Energy Technology Data Exchange (ETDEWEB)

Rezayan, Ali Hossein, E-mail: ahrezayan@ut.ac.ir [Department of Life Science Engineering, Faculty of New Sciences and Technologies, University of Tehran, Tehran (Iran, Islamic Republic of); Mousavi, Majid [Department of Life Science Engineering, Faculty of New Sciences and Technologies, University of Tehran, Tehran (Iran, Islamic Republic of); Kheirjou, Somayyeh [Department of Chemistry, Sharif University of Technology, Tehran (Iran, Islamic Republic of); Amoabediny, Ghasem [School of Chemical Engineering, College of Engineering, University of Tehran, Tehran (Iran, Islamic Republic of); Ardestani, Mehdi Shafiee [Department of Pharmacy, Tehran University of Medical Sciences, Tehran (Iran, Islamic Republic of); Mohammadnejad, Javad [Department of Life Science Engineering, Faculty of New Sciences and Technologies, University of Tehran, Tehran (Iran, Islamic Republic of)

2016-12-15

In this study, magnetic nanoparticles (MNPs) were synthesized via co-precipitation method. To enhance the biocompatibility and colloidal stability of the synthesized nanoparticles, they were modified with carboxyl functionalized PEG via dopamine (DPA) linker. Both modified and unmodified Fe{sub 3}O{sub 4} nanoparticles exhibited super paramagnetic behavior (particle size below 20 nm). The saturation magnetization (Ms) of PEGdiacid-modified Fe{sub 3}O{sub 4} was 45 emu/g, which was less than the unmodified Fe{sub 3}O{sub 4} nanoparticles (70 emu/g). This difference indicated that PEGdiacid polymer was immobilized on the surface of Fe{sub 3}O{sub 4} nanoparticles successfully. To evaluate the efficiency of the resulting nanoparticles as contrast agents for magnetic resonance imaging (MRI), different concentration of MNPs and different value of echo time TE were investigated. The results showed that by increasing the concentration of the nanoparticles, transverse relaxation time (T{sub 2}) decreased, which subsequently resulted in MR signal enhancement. T{sub 2}-weighted MR images of the different concentration of MNPs in different value of echo time TE indicated that MR signal intensity increased with increase in TE value up to 66 and then remained constant. The cytotoxicity effect of the modified and unmodified nanoparticles was evaluated in three different concentrations (12, 60 and 312 mg l{sup −1}) on MDA-MB-231 cancer cells for 24 and 48 h. In both tested time (24 and 48 h) for all three samples, the modified nanoparticles had long life time than unmodified nanoparticles. Cellular uptake of modified MNPs was 80% and reduced to 9% by the unmodified MNPs. - Highlights: • Magnetic nanoparticles (MNPs) were synthesized via co-precipitation method. • MNPs were modified with carboxyl functionalized PEG via dopamine (DPA) linker. • Modified and unmodified Fe{sub 3}O{sub 4} nanoparticles exhibited super paramagnetic behavior. • T{sub 2} decrease as MNPs

The relationship between growth and soluble sugar concentration of Aloe vera plants grown under three levels of irradiance

Energy Technology Data Exchange (ETDEWEB)

Paez, A.; Gebre, G.M.; Tschaplinski, T.J. (Universidad del Zulia (Venezuela))

1994-06-01

The CAM plant Aloe vera was vegetatively propagated and grown under three irradiances: full sun, partial and deep shade (30% and 10% of ambient light, respectively) to determine the effect on growth, biomass allocation, and sugar concentration. After one year, the plants were harvested to determine final dry weight and the sugar concentration of the leaf mucilaginous gel. Plants grown under full sun produced twice the total dry weight of those grown under partial shade, with the difference equally partitioned between the shoot and root. Plants grown under full sun also produced thicker leaves, and more numerous and large auxiliary shoots. The dry weight of plants grown under deep shade was 8.6% that of plants grown under full sun, which was directly proportional to the irradiance received. Partial shade increased the number and length of leaves produced on the primary shoot, but the allocation of carbon to roots was the lowest of all treatments. Partial shade reduced the total sugar concentration of the leaf gel matrix to 34% that of plants under full sun, due to reductions in all sugars measured. Glucose was the most abundant soluble sugar, with its relative contribution to the total pool increasing under shade. In summary, the proportional effects of partial shading were greater on soluble sugar concentrations than on the total plant biomass produced.

Regional trends in the fractional solubility of Fe and other metals from North Atlantic aerosols (GEOTRACES cruises GA01 and GA03 following a two-stage leach

Directory of Open Access Journals (Sweden)

R. U. Shelley

2018-04-01

Full Text Available The fractional solubility of aerosol-derived trace elements deposited to the ocean surface is a key parameter of many marine biogeochemical models. Despite this, it is currently poorly constrained, in part due to the complex interplay between the various processes that govern the solubilisation of aerosol trace elements. In this study, we used a sequential two-stage leach to investigate the regional variability in fractional solubility of a suite of aerosol trace elements (Al, Ti, Fe, Mn, Co, Ni, Cu, Zn, Cd, and Pb from samples collected during three GEOTRACES cruises to the North Atlantic Ocean (GA01, GA03-2010, and GA03-2011. We present aerosol trace element solubility data from two sequential leaches that provide a solubility window, covering a conservative lower limit to an upper limit, the maximum potentially soluble fraction, and discuss why this upper limit of solubility could be used as a proxy for the bioavailable fraction in some regions. Regardless of the leaching solution used in this study (mild versus strong leach, the most heavily loaded samples generally had the lowest solubility. However, there were exceptions. Manganese fractional solubility was relatively uniform across the full range of atmospheric loading (32 ± 13 and 49 ± 13 % for ultra high-purity water and 25 % acetic acid leaches, respectively. This is consistent with other marine aerosol studies. Zinc and Cd fractional solubility also appeared to be independent of atmospheric loading. Although the average fractional solubilities of Zn and Cd (37 ± 28 and 55 ± 30 % for Zn and 39 ± 23 and 58 ± 26 % for Cd, for ultra high-purity water and 25 % acetic acid leaches, respectively were similar to Mn, the range was greater, with several samples being 100 % soluble after the second leach. Finally, as the objective of this study was to investigate the regional variability in TE solubility, the samples were grouped according to air mass

A comparative study of metabolism and concentration factors of Fe, Cu, Zn, Mn, Co and Mg in Carcinus maenas and Cancer irroratus ovaries during ovogenesis

International Nuclear Information System (INIS)

Martin, J.-L.M.

1975-01-01

Fe, Cu, Zn, Mn, Co, and Mg were analysed in the ovary of Carcinus maenas and Cancer irroratus during ovogenesis. In both ovaries, the relatives rates, expressed as parts per millions as a ratio of wet and dry weight, are the following: Mg>Zn>Fe>Cu>Mn>Co, while in the hemolymph of Cancer irroratus these relative rates are the following: Mg>Cu>Zn>Fe>Mn>Co. Compared to concentrations of these metals in sea water, Mg expected, all metals in the ovary of Cancer irroratus have a concentration factor upper than 1. Compared to the concentration of metals in the hemolymph is, for Fe, Mn, and Co, the concentration factor upper than 1, and for Cu, Zn and Mg, the concentration factor lower than 1. A study of correlations was done between the concentrations of metals considered in pairs, and between the concentrations of metals and the parameters: water content and gonad index [fr

Solubility of NaNd(CO3)2.6H2O(c) in concentrated Na2CO3 and NaHCO3 solutions

International Nuclear Information System (INIS)

Rao, L.; Rai, D.; Felmy, A.R.; Fulton, R.W.; Novak, C.F.

1996-01-01

NaNd(CO 3 ) 2 x 6 H 2 O(c) was identified to be the final equilibrium solid phase in suspensions containing concentrated sodium carbonate (0.1 to 2.0 M) and sodium bicarbonate (0.1 to 1.0 M), with either NaNd(CO 3 ) 2 x 6 H 2 O(c) or Nd 2 (CO 3 ) 3 x xH 2 O(s) as initial solids. A thermodynamic model, based on Pitzer's specific into-interaction approach, was developed to interpret the solubility of NaNd(CO 3 ) 2 x 6 H 2 O(c) as functions of sodium carbonate and sodium bicarbonate concentrations. In this model, the solubility data of NaNd(CO 3 ) 2 x 6 H 2 O(c) were explained by assuming the formation of NdCO 3 + , Nd(CO 3 ) 2 - and Nd(CO 3 ) 3 3- species and invoking the specific ion interactions between Na + and Nd(CO 3 ) 3 3- . Ion interaction parameters for Na + -Nd(CO 3 ) 3 3- were developed to fit the solubility data. Based on the model calculations, Nd(CO 3 ) 3 3- was the predominant aqueous neodymium species in 0.1 to 2 M sodium carbonate and 0.1 to 1 M sodium bicarbonate solutions. The logarithm of the NaNd(CO 3 ) 2 x 6 H 2 O solubility product (NaNd(CO 3 ) 2 x 6 H 2 O(c)=Na + +Nd 3+ +2 CO 3 2- +6 H 2 O) was calculated to be -21.39. This model also provided satisfactory interpretation of the solubility data of the analogous Am(III) system in less concentrated carbonate and bicarbonate solutions. (orig.)

Plasma concentrations of water.soluble vitamins in metabolic ...

African Journals Online (AJOL)

Context: Vitamins B1 (thiamine), B3 (niacin), B6 (pyridoxine), and C (ascorbic acid) are vital for energy, carbohydrate, lipid, and amino acid metabolism and in the regulation of the cellular redox state. Some studies have associated low levels of water.soluble vitamins with metabolic syndrome and its various components.

DEPENDENCY OF SULFATE SOLUBILITY ON MELT COMPOSITION AND MELT POLYMERIZATION

International Nuclear Information System (INIS)

JANTZEN, CAROL M.

2004-01-01

Sulfate and sulfate salts are not very soluble in borosilicate waste glass. When sulfate is present in excess it can form water soluble secondary phases and/or a molten salt layer (gall) on the melt pool surface which is purported to cause steam explosions in slurry fed melters. Therefore, sulfate can impact glass durability while formation of a molten salt layer on the melt pool can impact processing. Sulfate solubility has been shown to be compositionally dependent in various studies, (e.g. , B2O3, Li2O, CaO, MgO, Na2O, and Fe2O3 were shown to increase sulfate solubility while Al2O3 and SiO2 decreased sulfate solubility). This compositional dependency is shown to be related to the calculated melt viscosity at various temperatures and hence the melt polymerization

Suppression of aqueous corrosion of La(Fe0.88Si0.12)13 by reducing dissolved oxygen concentration for high-performance magnetic refrigeration

International Nuclear Information System (INIS)

Fujieda, S.; Fukamichi, K.; Suzuki, S.

2014-01-01

Highlights: • The aqueous corrosion of La(Fe 0.88 Si 0.12 ) 13 and its suppression were investigated. • The lattice expansion after immersion was caused by the hydrogen absorption. • The itinerant-electron metamagnetic transition became indistinct after immersion. • The aqueous corrosion was suppressed by reducing the dissolved oxygen concentration. - Abstract: The itinerant-electron metamagnetic transition of La(Fe 0.88 Si 0.12 ) 13 becomes indistinct after immersion in distilled-water containing about 8 ppm of the dissolved oxygen (DO) concentration because of aqueous corrosion. However, the aqueous corrosion of La(Fe 0.88 Si 0.12 ) 13 is significantly suppressed by reducing the DO concentration. Thus, isothermal magnetic entropy change after immersion for 30 days in deaerated distilled-water with a DO concentration less than 0.1 ppm is larger than that after immersion for 5 days in distilled-water containing about 8 ppm of the DO concentration. Consequently, the reduction of the DO concentration is effective for preservation of the excellent magnetocaloric effects of La(Fe 0.88 Si 0.12 ) 13 in an aqueous solution, which is a promising heat transfer fluid of room-temperature magnetic refrigeration

Study of hydrogenation of Sm{sub 2}Fe{sub 17-y}Ga{sub y} by means of X-ray diffraction

Energy Technology Data Exchange (ETDEWEB)

Teresiak, A.; Uhlemann, M.; Kubis, M.; Gebel, B.; Mattern, N.; Mueller, K.-H. [Institut fuer Festkoerper- und Werkstofforschung Dresden e.V. (Germany)

2000-06-06

The hydrogenation process of Sm{sub 2}Fe{sub 17-y}Ga{sub y}(y=0-2) was studied. X-ray investigations show a decreasing hydrogen solubility in the intermetallic alloy with increasing Ga-content from 4.0{+-}0.3 atoms per formula unit for Sm{sub 2}Fe{sub 17} to 2.85{+-}0.05 for Sm{sub 2}Fe{sub 15}Ga{sub 2}. The larger Ga atoms reduce the size of the interstitial sites and thereby the maximum hydrogen concentration is decreased. The behaviour of the lattice parameters a and c with increasing Ga content points to a changed hydrogen distribution on the interstitial sites, becoming more statistical. In situ observations by means of high temperature X-ray diffraction show that the hydrogen absorption process is diffusion controlled. The hydrogen absorption starts at an annealing temperature of 120-140 C in all cases. The solubility of hydrogen decreases with increasing temperature. The hydrogen is completely desorbed above 350 C in all cases. The absorption/desorption process is reversible between room temperature and 400 C. Annealing at temperatures above 400 C leads to the decomposition of the Sm{sub 2}Fe{sub 17} phase, indicated by emerging of {alpha}-Fe. The formation of SmH{sub x} is established at 600 C. The decomposition temperature increases with increasing Ga-content. Up to 750 C, only Sm{sub 2}Fe{sub 17} is completely decomposed. (orig.)

Solubility and acid-base properties of concentrated phytate in self-medium and in NaCl{sub aq} at T = 298.15 K

Energy Technology Data Exchange (ETDEWEB)

Cigala, Rosalia Maria; Crea, Francesco; Lando, Gabriele; Milea, Demetrio [Dipartimento di Chimica Inorganica, Chimica Analitica e Chimica Fisica, Universita di Messina, Via Ferdinando Stagno d' Alcontres, 31, I-98166 Messina (Vill. S. Agata) (Italy); Sammartano, Silvio, E-mail: ssammartano@unime.i [Dipartimento di Chimica Inorganica, Chimica Analitica e Chimica Fisica, Universita di Messina, Via Ferdinando Stagno d' Alcontres, 31, I-98166 Messina (Vill. S. Agata) (Italy)

2010-11-15

The acid-base properties of concentrated phytic acid were studied in self-medium and in NaCl{sub aq} (0.5 {<=} I/mol . L{sup -1} {<=} 4.0) by ISE-H{sup +} potentiometry and by direct calorimetry, at T = 298.15 K. At ligand concentrations c{sub (Phy)} > 0.012 mol . L{sup -1}, the formation of several binuclear H{sub i}(Phy){sub 2} (2 {<=} i {<=} 10) species was observed, in addition to the mononuclear H{sub i}Phy (1 {<=} i {<=} 7) ones. The solubility of phytate dodecasodium salt was studied in pure water and in NaCl{sub aq} at different ionic strengths; the total solubility in pure water is S{sub 0}{sup T}=(0.300{+-}0.004)mol.L{sup -1} and it decreases markedly with increasing ionic strength; for example the total solubility of Na{sub 12}Phy at I = 3.0 mol . L{sup -1} is 0.008 mol . L{sup -1}. By the dependence on ionic strength (salt concentration) of the solubility, it was possible to calculate the activity coefficients of phytate as a function of medium concentration. Direct calorimetric titrations were also carried out on Na{sub 12}Phy aqueous solutions at different phytate concentrations (0.025 {<=} c{sub (Phy)}/mol . L{sup -1} {<=} 0.100) and without addition of supporting electrolyte, in order to calculate the enthalpy changes for the protonation equilibria in self-medium of the binuclear H{sub i}(Phy){sub 2} species, at T = 298.15 K. It was observed that the {Delta}H/kJ . mol{sup -1} of the binuclear species are, within the experimental error, independent of the ionic strength; for example for the H{sub 2}(Phy){sub 2} species we obtained: {Delta}H{sub 22} = (-23.6 {+-} 0.6) kJ . mol{sup -1}, and (-23.7 {+-} 0.2) kJ . mol{sup -1} at I = 0.50 and 2.0 mol . L{sup -1}, respectively.

Effect of condensed corn distillers solubles concentration on lactation performance of Holstein cows.

Science.gov (United States)

McCormick, M E; Forbes, S; Moreira, V R; Blouin, D C; Han, K J

2015-03-01

Forty-eight Holstein cows (32 multiparous and 16 primiparous) in mid to late lactation averaging 219±71 days in milk and 30.5±6.6 kg/d of 3.5% fat-corrected milk were used in a 56-d completely randomized design experiment to evaluate condensed corn distillers solubles (CCDS) inclusion in high-fiber total mixed rations (TMR). Inclusion rates evaluated were 0, 6.6, 13.2, and 19.8% CCDS as a percentage of dry matter (DM). Distiller solubles substituted for soybean meal, corn grain, and whole cottonseed such that diets were similar in protein (16.6%) and fat (4.50%). Water was added to 0, 6.6, and 13.2% CCDS treatments so that final TMR DM concentrations (47.8%) were similar across diets. The forage portion of the diet was kept constant at 19.6% annual ryegrass hay and 26.0% sorghum baleage. Diet in vitro true digestibility tended to increase as CCDS addition increased, but neutral detergent fiber digestibility trended lower in CCDS diets. Percent P (0.39, 0.55, 0.69, and 0.73%) and S (0.32, 0.35, 0.39, and 0.42%) in TMR increased as CCDS concentration increased. Milk yield (23.5, 24.7, 25.5, and 24.8 kg/d of 3.5% fat-corrected milk) was similar for control and CCDS diets. Milk fat (3.88, 3.73, 3.78, and 3.68%), protein (3.28, 3.27, 3.31, and 3.31%), and lactose (4.61, 4.66, 4.69, and 4.77) percentages were similar across diets. Milk urea nitrogen (16.60, 15.58, 15.43, and 14.75 mg/dL) declined with increasing CCDS addition. Animal activity, body weight, body condition scores, and locomotion scores were not influenced by CCDS. Day 28 poststudy locomotion scores were similar across diets. Ruminal acetate concentrations did not differ among diets, but propionate and butyrate concentrations were elevated in rumen fluid of cows receiving 19.6% CCDS. Although rumen fluid pH values were similar (6.5, 6.4, 6.3, and 6.2), the two highest CCDS diets exhibited depressed acetate:propionate ratios relative to controls. The results from this study indicate that CCDS may be

Concentrations of Water-Soluble Vitamins in Blood and Urinary Excretion in Patients with Diabetes Mellitus

Directory of Open Access Journals (Sweden)

Hiromi Iwakawa

2016-01-01

Full Text Available We examined the concentrations of water-soluble vitamins in blood and urinary excretion of 22 patients with type 2 diabetes mellitus (type 2DM and 20 healthy control participants. Macronutrient and vitamin intakes of type 2DM subjects were measured using a weighed food record method. Control participants consumed a semipurified diet for eight days. Multiple linear regression models were used to determine whether significant differences existed in vitamin concentrations in blood independent of age, sex, and other confounding factors. Concentrations of vitamins B2, B6, C, niacin, and folate in blood were significantly lower in type 2DM subjects than in controls, independent of confounding factors. Renal clearances of vitamins B6, C, niacin, and folate were significantly higher in type 2DM subjects than in controls. In conclusion, concentrations of vitamins B2, B6, C, niacin, and folate in blood were significantly lower in type 2DM subjects than in controls, independent of confounding factors; based on the evidence of increased urinary clearance of these vitamins, the lower levels were likely due to impaired reabsorption processes.

Concentrations of Water-Soluble Vitamins in Blood and Urinary Excretion in Patients with Diabetes Mellitus.

Science.gov (United States)

Iwakawa, Hiromi; Nakamura, Yasuyuki; Fukui, Tomiho; Fukuwatari, Tsutomu; Ugi, Satoshi; Maegawa, Hiroshi; Doi, Yukio; Shibata, Katsumi

2016-01-01

We examined the concentrations of water-soluble vitamins in blood and urinary excretion of 22 patients with type 2 diabetes mellitus (type 2DM) and 20 healthy control participants. Macronutrient and vitamin intakes of type 2DM subjects were measured using a weighed food record method. Control participants consumed a semipurified diet for eight days. Multiple linear regression models were used to determine whether significant differences existed in vitamin concentrations in blood independent of age, sex, and other confounding factors. Concentrations of vitamins B2, B6, C, niacin, and folate in blood were significantly lower in type 2DM subjects than in controls, independent of confounding factors. Renal clearances of vitamins B6, C, niacin, and folate were significantly higher in type 2DM subjects than in controls. In conclusion, concentrations of vitamins B2, B6, C, niacin, and folate in blood were significantly lower in type 2DM subjects than in controls, independent of confounding factors; based on the evidence of increased urinary clearance of these vitamins, the lower levels were likely due to impaired reabsorption processes.

Determination of water-soluble and fat-soluble vitamins in tears and blood serum of infants and parents by liquid chromatography/mass spectrometry.

Science.gov (United States)

Khaksari, Maryam; Mazzoleni, Lynn R; Ruan, Chunhai; Kennedy, Robert T; Minerick, Adrienne R

2017-02-01

Tears serve as a viable diagnostic fluid with advantages including less invasive sample to collect and less complex to prepare for analysis. Several water-soluble and fat-soluble vitamins were detected and quantified in human tears and compared with blood serum levels. Samples from 15 family pairs, each pair consisting of a four-month-old infant and one parent were analyzed; vitamin concentrations were compared between tears and blood serum for individual subjects, between infants and parents, and against self-reported dietary intakes. Water-soluble vitamins B 1 , B 2 , B 3 (nicotinamide), B 5 , B 9 and fat-soluble vitamin E (α-tocopherol) were routinely detected in tears and blood serum while fat-soluble vitamin A (retinol) was detected only in blood serum. Water-soluble vitamin concentrations measured in tears and blood serum of single subjects were comparable, while higher concentrations were measured in infants compared to their parents. Fat-soluble vitamin E concentrations were lower in tears than blood serum with no significant difference between infants and parents. Serum vitamin A concentrations were higher in parents than infants. Population trends were compiled and quantified using a cross correlation factor. Strong positive correlations were found between tear and blood serum concentrations of vitamin E from infants and parents and vitamin B 3 concentrations from parents, while slight positive correlations were detected for infants B 3 and parents B 1 and B 2 concentrations. Correlations between infants and parents were found for the concentrations of B 1 , B 2 , B 3 , and E in tears, and the concentrations of B 2, A, and E in blood serum. Stronger vitamin concentration correlations were found between infants and parents for the breast-fed infants, while no significant difference was observed between breast-fed and bottle-fed infants. This work is the first to demonstrate simultaneous vitamin A, B, and E detection and to quantify correlations between

The water-soluble fraction of potentially toxic elements in contaminated soils: relationships between ecotoxicity, solubility and geochemical reactivity.

Science.gov (United States)

Rocha, L; Rodrigues, S M; Lopes, I; Soares, A M V M; Duarte, A C; Pereira, E

2011-09-01

To better understand the impacts posed by soil contamination to aquatic ecosystems it is crucial to characterise the links between ecotoxicity, chemical availability and geochemical reactivity of potentially toxic elements (PTE's) in soils. We evaluated the adverse effects of water extracts obtained from soils contaminated by chemical industry and mining, using a test battery including organisms from different trophic levels (bacteria, algae and daphnids). These tests provided a quick assessment of the ecotoxicity of soils with respect to possible adverse effects on aquatic organisms although the ecotoxicological responses could be related to the solubility of PTE's only to a limited extent. The analysis of results of bioassays together with the chemical characterisation of water extracts provided additional relevant insight into the role of conductivity, pH, Al, Fe, and Mn of soil extracts on toxicity to organisms. Furthermore, an important conclusion of this study was that the toxicity of extracts to the aquatic organisms could also be related to the soil properties (pH, Org C and Fe(ox)) and to the reactivity of PTE's in soils which in fact control the soluble fraction of the contaminants. The combined assessment of ecotoxicity in water fractions, solubility and geochemical reactivity of PTE's in soils provided a more comprehensive understanding of the bioavailability of inorganic contaminants than ecotoxicological or chemical studies alone and can therefore be most useful for environmental risks assessment of contaminated soils. Copyright © 2011 Elsevier Ltd. All rights reserved.

The solubility and site preference of Fe3+ in Li7-3xFexLa3Zr2O12 garnets

Science.gov (United States)

Rettenwander, D.; Geiger, C. A.; Tribus, M.; Tropper, P.; Wagner, R.; Tippelt, G.; Lottermoser, W.; Amthauer, G.

2015-10-01

A series of Fe3+-bearing Li7La3Zr2O12 (LLZO) garnets was synthesized using solid-state synthesis methods. The synthetic products were characterized compositionally using electron microprobe analysis and inductively coupled plasma optical emission spectroscopy (ICP-OES) and structurally using X-ray powder diffraction and 57Fe Mössbauer spectroscopy. A maximum of about 0.25 Fe3+ pfu could be incorporated in Li7-3xFexLa3Zr2O12 garnet solid solutions. At Fe3+ concentrations lower than about 0.16 pfu, both tetragonal and cubic garnets were obtained in the synthesis experiments. X-ray powder diffraction analysis showed only a garnet phase for syntheses with starting materials having intended Fe3+ contents lower than 0.52 Fe3+ pfu. Back-scattered electron images made with an electron microprobe also showed no phase other than garnet for these compositions. The lattice parameter, a0, for all solid-solution garnets is similar with a value of a0≈12.98 Å regardless of the amount of Fe3+. 57Fe Mössbauer spectroscopic measurements indicate the presence of poorly- or nano-crystalline FeLaO3 in syntheses with Fe3+ contents greater than 0.16 Fe3+ pfu. The composition of different phase pure Li7-3xFexLa3Zr2O12 garnets, as determined by electron microprobe (Fe, La, Zr) and ICP-OES (Li) measurements, give Li6.89Fe0.03La3.05Zr2.01O12, Li6.66Fe0.06La3.06Zr2.01O12, Li6.54Fe0.12La3.01Zr1.98O12, and Li6.19Fe0.19La3.02Zr2.04O12. The 57Fe Mössbauer spectrum of cubic Li6.54Fe0.12La3.01Zr1.98O12 garnet indicates that most Fe3+ occurs at the special crystallographic 24d position, which is the standard tetrahedrally coordinated site in garnet. Fe3+ in smaller amounts occurs at a general 96h site, which is only present for certain Li-oxide garnets, and in Li6.54Fe0.12La3.01Zr1.98O12 this Fe3+ has a distorted 4-fold coordination.

Synthesis, characterization and stability of Cr(III) and Fe(III) hydroxides

Energy Technology Data Exchange (ETDEWEB)

Papassiopi, N.; Vaxevanidou, K.; Christou, C.; Karagianni, E.; Antipas, G.S.E., E-mail: gantipas@metal.ntua.gr

2014-01-15

Highlights: • Fe(III)–Cr(III) hydroxides enhance groundwater quality better than pure Cr(III) compounds. • Crystalline Cr(OH){sub 3}·3H{sub 2}O was unstable, with a solubility higher than 50 μg/l. • Amorphous Cr(OH){sub 3}(am) was stable with a solubility lower than 50 μg/l in the range 5.7 < pH < 11. • For mixed Fe{sub 0.75}Cr{sub 0.25}(OH){sub 3}, the stability region was extended to 4.8 < pH < 13.5. -- Abstract: Chromium is a common contaminant of soils and aquifers and constitutes a major environmental problem. In nature, chromium usually exists in the form of two oxidation states, trivalent, Cr(III), which is relatively innocuous for biota and for the aquatic environment, and hexavalent, Cr(VI) which is toxic, carcinogenic and very soluble. Accordingly, the majority of wastewater and groundwater treatment technologies, include a stage where Cr(VI) is reduced to Cr(III), in order to remove chromium from the aqueous phase and bind the element in the form of environmentally stable solid compounds. In the absence of iron the final product is typically of the form Cr(OH){sub 3}·xH{sub 2}O whereas in the presence of iron the precipitate is a mixed Fe{sub (1−x)}Cr{sub x}(OH){sub 3} phase. In this study, we report on the synthesis, characterisation and stability of mixed (Fe{sub x},Cr{sub 1−x})(OH){sub 3} hydroxides as compared to the stability of Cr(OH){sub 3}. We established that the plain Cr(III) hydroxide, abiding to the approximate molecular formula Cr(OH){sub 3}·3H{sub 2}O, was crystalline, highly soluble, i.e. unstable, with a tendency to transform into the stable amorphous hydroxide Cr(OH){sub 3}(am) phase. Mixed Fe{sub 0.75}Cr{sub 0.25}(OH){sub 3} hydroxides were found to be of the ferrihydrite structure, Fe(OH){sub 3}, and we correlated their solubility to that of a solid solution formed by plain ferrihydrite and the amorphous Cr(III) hydroxide. Both our experimental results and thermodynamic calculations indicated that mixed Fe

Ab initio and Atomic kinetic Monte Carlo modelling of segregation in concentrated FeCrNi alloys

Science.gov (United States)

Piochaud, J. B.; Becquart, C. S.; Domain, C.

2014-06-01

Internal structure of pressurised water reactors are made of austenitic materials. Under irradiation, the microstructure of these concentrated alloys evolves and solute segregation on grain boundaries or irradiation defects such as dislocation loops are observed to take place. In order to model and predict the microstructure evolution, a multiscale modelling approach needs to be developed, which starts at the atomic scale. Atomic Kinetic Monte Carlo (AKMC) modelling is the method we chose to provide an insight on defect mediated diffusion under irradiation. In that approach, we model the concentrated commercial steel as a FeCrNi alloy (γ-Fe70Cr20Ni10). As no reliable empirical potential exists at the moment to reproduce faithfully the phase diagram and the interactions of the elements and point defects, we have adjusted a pair interaction model on large amount of DFT calculations. The point defect properties in the Fe70Cr20Ni10, and more precisely, how their formation energy depends on the local environment will be presented and some AKMC results on thermal non equilibrium segregation and radiation induce segregation will be presented. The effect of Si on the segregation will also be discussed.

Progress in the research of neptunium solubility

International Nuclear Information System (INIS)

Jiang Tao; Liu Yongye; Yao Jun

2012-01-01

237 Np is considered a possible long-term potential threat for environment, because of its long half-life, high toxicity and its mobile nature under aerobic conditions due to the high chemical stability of its pentavalent state. Therefore 237 Np is considered as one of high-level radioactive waste and need to be disposed in deep geologic disposal repository. The dissolution behavior is an important aspect of migration research. The solubility is considered very important for high level waste geological disposal safety and environmental evaluation. The solubility determines the maximum concentration of the discharge, and then it is initial concentration of the radionuclides migration to the environment. The solubility impact directly on radionuclides migration in host rock, and can be used to predict the concentration and speciation of radionuclides in groundwater around disposal sites many years later. This paper focused on research results of the solubility, some proposals for Np dissolution chemistry research were also been suggested. (authors)

Immobilization of radionuclides and heavy metals through anaerobic bio-oxidation of Fe(II)

International Nuclear Information System (INIS)

Lack, J.G.; Chaudhuri, S.K.; Kelly, S.D.; Kemner, K.M.; O'Connor, S.M.; Coates, J.D.

2002-01-01

Adsorption of heavy metals and radionuclides (HMR) onto iron and manganese oxides has long been recognized as an important reaction for the immobilization of these compounds. However, in environments containing elevated concentrations of these HMR the adsorptive capacity of the iron and manganese oxides may well be exceeded, and the HMR can migrate as soluble compounds in aqueous systems. Here we demonstrate the potential of a bioremediative strategy for HMR stabilization in reducing environments based on the recently described anaerobic nitrate-dependent Fe(II) oxidation by Dechlorosoma species. Bio-oxidation of 10 mM Fe(II) and precipitation of Fe(III) oxides by these organisms resulted in rapid adsorption and removal of 55 μM uranium and 81 μM cobalt from solution. The adsorptive capacity of the biogenic Fe(III) oxides was lower than that of abiotically produced Fe(III) oxides (100 μM for both metals), which may have been a result of steric hindrance by the microbial cells on the iron oxide surfaces. The binding capacity of the biogenic oxides for different heavy metals was indirectly correlated to the atomic radius of the bound element. X-ray absorption spectroscopy indicated that the uranium was bound to the biogenically produced Fe(III) oxides as U(VI) and that the U(VI) formed bidentate and tridentate inner-sphere complexes with the Fe(III) oxide surfaces. Dechlorosoma suillum oxidation was specific for Fe(II), and the organism did not enzymatically oxidize U(IV) or Co(II). Small amounts (less than 2.5 μM) of Cr(III) were reoxidized by D. suillum; however, this appeared to be inversely dependent on the initial concentration of the Cr(III). The results of this study demonstrate the potential of this novel approach for stabilization and immobilization of HMR in the environment.

Determination of water-soluble vitamins using a colorimetric microbial viability assay based on the reduction of water-soluble tetrazolium salts.

Science.gov (United States)

Tsukatani, Tadayuki; Suenaga, Hikaru; Ishiyama, Munetaka; Ezoe, Takatoshi; Matsumoto, Kiyoshi

2011-07-15

A method for the determination of water-soluble vitamins using a colorimetric microbial viability assay based on the reduction of the tetrazolium salt {2-(2-methoxy-4-nitrophenyl)-3-(4-nitrophenyl)-5-(2,4-disulfophenyl)-2H-tetrazolium, monosodium salt (WST-8)} via 2-methyl-1,4-napthoquinone (NQ) was developed. Measurement conditions were optimized for the microbiological determination of water-soluble vitamins, such as vitamin B(6), biotin, folic acid, niacin, and pantothenic acid, using microorganisms that have a water-soluble vitamin requirement. A linear relationship between absorbance and water-soluble vitamin concentration was obtained. The proposed method was applied to determine the concentration of vitamin B(6) in various foodstuffs. There was good agreement between vitamin B(6) concentrations determined after 24h using the WST-8 colorimetric method and those obtained after 48h using a conventional method. The results suggest that the WST-8 colorimetric assay is a useful method for the rapid determination of water-soluble vitamins in a 96-well microtiter plate. Copyright © 2011 Elsevier Ltd. All rights reserved.

Immobilization of uranium in the presence of Fe0(s): Model development and simulation of contrasting experimental conditions

International Nuclear Information System (INIS)

Wang Yong; Salvage, Karen

2005-01-01

A geochemical model is developed for the immobilization of U in the presence of metallic Fe. Zero-valent iron (ZVI) serves as a reducing agent inducing the reductive-precipitation of U, and ZVI corrosion products can serve as absorbing agents for U. The numerical model developed allows the complex interactions of U in solution in differing concentrations to be examined, under variable pH and redox conditions, with or without carbonate, in the presence of ZVI of different size and surface area. It incorporates Fe corrosion, Fe(II) and Fe(III) corrosion product formation, reductive-precipitation of U from the soluble U(VI) valence to the poorly soluble U(IV) valence, adsorption/de-sorption of U onto the Fe oxide corrosion products, and aqueous speciation. The processes of Fe corrosion and reductive precipitation of U are simulated as non-equilibrium, an improvement over other geochemical models. The reductive-precipitation process may use either ZVI or Fe(II) as the reducing agent. The model is calibrated using 3 separate sets of experimental data from published literature that cover a wide range of redox conditions. Sensitivity of the model predictions to variations in input parameters is examined. The simulation results show that the different published experimental results can be explained by different solution chemistries in the studies, specifically O 2 and CO 2 availability and pH, and the amount and surface area of the metallic Fe. With this numerical model the behavior of U in ZVI containing systems over a range of conditions realistic for groundwater can be investigated. By synthesizing observations across several experimental studies, it will lead to a broader understanding of the processes controlling U immobilization under varied geochemical conditions

Statistical model and first-principles simulation on concentration of HenV cluster and He bubble formation in α-Fe and W

Science.gov (United States)

Liu, Yue-Lin; Yu, Yang; Dai, Zhen-Hong

2015-01-01

Using first-principles calculations, we investigate the stabilities of He and Hen-vacancy (HenV) clusters in α-Fe and W. Vacancy formation energies are 2.08 eV in α-Fe and 3.11 eV in W, respectively. Single He in both α-Fe and W prefers to occupy the tetrahedral interstitial site. We recalculated the He solution energy considering the effect of zero-point energy (ZPE). The ZPEs of He in α-Fe and W at the tetrahedral (octahedral) interstitial site are 0.072 eV (0.031 eV) and 0.078 eV (0.034 eV), respectively. The trapping energies of single He at vacancy in α-Fe and W are -2.39 eV and -4.55 eV, respectively. By sequentially adding He into vacancy, a monovacancy trap up to 10 He atoms distributing in the vacancy vicinity. Based on the above results combined with statistical model, we evaluate the concentrations of all relevant HenV clusters as a function of He chemical potential. The critical HenV concentration is found to be ∼10-40 (atomic) at the critical temperature T = 600 K in α-Fe and T = 1600 K in W, respectively. Beyond the critical HenV concentrations, considerable HenV aggregate to form HenVm clusters. By further growing of HenVm, the HenVm clusters grow bigger resulting in the larger He bubble formation.

Particle Size, Surface Area, and Amorphous Content as Predictors of Solubility and Bioavailability for Five Commercial Sources of Ferric Orthophosphate in Ready-To-Eat Cereal.

Science.gov (United States)

Dickmann, Robin S; Strasburg, Gale M; Romsos, Dale R; Wilson, Lori A; Lai, Grace H; Huang, Hsimin

2016-03-01

Ferric orthophosphate (FePO₄) has had limited use as an iron fortificant in ready-to-eat (RTE) cereal because of its variable bioavailability, the mechanism of which is poorly understood. Even though FePO₄ has desirable sensory properties as compared to other affordable iron fortificants, few published studies have well-characterized its physicochemical properties. Semi-crystalline materials such as FePO₄ have varying degrees of molecular disorder, referred to as amorphous content, which is hypothesized to be an important factor in bioavailability. The objective of this study was to systematically measure the physicochemical factors of particle size, surface area, amorphous content, and solubility underlying the variation in FePO₄ bioavailability. Five commercial FePO₄ sources and ferrous sulfate were added to individual batches of RTE cereal. The relative bioavailability value (RBV) of each iron source, determined using the AOAC Rat Hemoglobin Repletion Bioassay, ranged from 51% to 99% (p Solubility in dilute HCl accurately predicted RBV (R² = 0.93, p = 0.008). Amorphous content measured by Dynamic Vapor Sorption ranged from 1.7% to 23.8% and was a better determinant of solubility (R² = 0.91; p = 0.0002) than surface area (R² = 0.83; p = 0.002) and median particle size (R² = 0.59; p = 0.12). The results indicate that while solubility of FePO₄ is highly predictive of RBV, solubility, in turn, is strongly linked to amorphous content and surface area. This information may prove useful for the production of FePO₄ with the desired RBV.

The 480 deg. C and 405 deg. C isothermal sections of the phase diagram of Fe-Zn-Si ternary system

Energy Technology Data Exchange (ETDEWEB)

Wang Jianhua [Institute of Materials Research, School of Mechanical Engineering, Xiangtan University, Hunan 411105 (China)]. E-mail: super_wang111@hotmail.com; Su Xuping [Institute of Materials Research, School of Mechanical Engineering, Xiangtan University, Hunan 411105 (China); Yin Fucheng [Institute of Materials Research, School of Mechanical Engineering, Xiangtan University, Hunan 411105 (China); Li Zhi [Institute of Materials Research, School of Mechanical Engineering, Xiangtan University, Hunan 411105 (China); Zhao Manxiu [Institute of Materials Research, School of Mechanical Engineering, Xiangtan University, Hunan 411105 (China)

2005-08-16

The 480 deg. C and 405 deg. C isothermal sections of the Fe-Zn-Si ternary phase diagram have been determined experimentally using scanning electron microscopy (SEM) coupled with energy dispersive X-ray spectroscopy (EDS) and X-ray diffractometry. The research of the work has concentrated on the Zn-rich corner, which is relevant to general galvanizing. The present studies have confirmed the existence of equilibrium state between the liquid, the {zeta} phase and the FeSi phase at the 480 deg. C isothermal section. There exist some changes in the phase relationships compared with the isothermal section at 450 deg. C. Experimental results indicate that Si solubility in all four Zn-Fe compounds is also limited at 480 deg. C and 405 deg. C.

Importance of reduced sulfur for the equilibrium chemistry and kinetics of Fe(II), Co(II) and Ni(II) supplemented to semi-continuous stirred tank biogas reactors fed with stillage

Energy Technology Data Exchange (ETDEWEB)

Shakeri Yekta, Sepehr, E-mail: sepehr.shakeri.yekta@liu.se [Department of Thematic Studies – Water and Environmental Studies, Linköping University, SE-581 83 Linköping (Sweden); Lindmark, Amanda [Department of Thematic Studies – Water and Environmental Studies, Linköping University, SE-581 83 Linköping (Sweden); Skyllberg, Ulf [Department of Forest Ecology and Management, Swedish University of Agricultural Sciences, SE-901 83 Umeå (Sweden); Danielsson, Åsa; Svensson, Bo H. [Department of Thematic Studies – Water and Environmental Studies, Linköping University, SE-581 83 Linköping (Sweden)

2014-03-01

Highlights: • Thermodynamics and kinetics of Fe, Co and Ni added to biogas reactors were studied. • Formation of Fe-sulfide and Fe-thiol aqueous complexes controlled the Fe solubility. • Cobalt solubility was controlled by processes independent of Co-sulfide interaction. • Iron added to the biogas reactors effected the Ni speciation and solubility. - Abstract: The objective of the present study was to assess major chemical reactions and chemical forms contributing to solubility and speciation of Fe(II), Co(II), and Ni(II) during anaerobic digestion of sulfur (S)-rich stillage in semi-continuous stirred tank biogas reactors (SCSTR). These metals are essential supplements for efficient and stable performance of stillage-fed SCSTR. In particular, the influence of reduced inorganic and organic S species on kinetics and thermodynamics of the metals and their partitioning between aqueous and solid phases were investigated. Solid phase S speciation was determined by use of S K-edge X-ray absorption near-edge spectroscopy. Results demonstrated that the solubility and speciation of supplemented Fe were controlled by precipitation of FeS(s) and formation of the aqueous complexes of Fe-sulfide and Fe-thiol. The relatively high solubility of Co (∼20% of total Co content) was attributed to the formation of compounds other than Co-sulfide and Co-thiol, presumably of microbial origin. Nickel had lower solubility than Co and its speciation was regulated by interactions with FeS(s) (e.g. co-precipitation, adsorption, and ion substitution) in addition to precipitation/dissolution of discrete NiS(s) phase and formation of aqueous Ni-sulfide complexes.

Importance of reduced sulfur for the equilibrium chemistry and kinetics of Fe(II), Co(II) and Ni(II) supplemented to semi-continuous stirred tank biogas reactors fed with stillage

International Nuclear Information System (INIS)

Shakeri Yekta, Sepehr; Lindmark, Amanda; Skyllberg, Ulf; Danielsson, Åsa; Svensson, Bo H.

2014-01-01

Highlights: • Thermodynamics and kinetics of Fe, Co and Ni added to biogas reactors were studied. • Formation of Fe-sulfide and Fe-thiol aqueous complexes controlled the Fe solubility. • Cobalt solubility was controlled by processes independent of Co-sulfide interaction. • Iron added to the biogas reactors effected the Ni speciation and solubility. - Abstract: The objective of the present study was to assess major chemical reactions and chemical forms contributing to solubility and speciation of Fe(II), Co(II), and Ni(II) during anaerobic digestion of sulfur (S)-rich stillage in semi-continuous stirred tank biogas reactors (SCSTR). These metals are essential supplements for efficient and stable performance of stillage-fed SCSTR. In particular, the influence of reduced inorganic and organic S species on kinetics and thermodynamics of the metals and their partitioning between aqueous and solid phases were investigated. Solid phase S speciation was determined by use of S K-edge X-ray absorption near-edge spectroscopy. Results demonstrated that the solubility and speciation of supplemented Fe were controlled by precipitation of FeS(s) and formation of the aqueous complexes of Fe-sulfide and Fe-thiol. The relatively high solubility of Co (∼20% of total Co content) was attributed to the formation of compounds other than Co-sulfide and Co-thiol, presumably of microbial origin. Nickel had lower solubility than Co and its speciation was regulated by interactions with FeS(s) (e.g. co-precipitation, adsorption, and ion substitution) in addition to precipitation/dissolution of discrete NiS(s) phase and formation of aqueous Ni-sulfide complexes

Solubility of xenon in amino-acid solutions. II. Nine less-soluble amino acids

Science.gov (United States)

Kennan, Richard P.; Himm, Jeffrey F.; Pollack, Gerald L.

1988-05-01

Ostwald solubility (L) of xenon gas, as the radioisotope 133Xe, has been measured as a function of solute concentration, at 25.0 °C, in aqueous solutions of nine amino acids. The amino-acid concentrations investigated covered much of their solubility ranges in water, viz., asparagine monohydrate (0-0.19 M), cysteine (0-1.16 M), glutamine (0-0.22 M), histidine (0-0.26 M), isoleucine (0-0.19 M), methionine (0-0.22 M), serine (0-0.38 M), threonine (0-1.4 M), and valine (0-0.34 M). We have previously reported solubility results for aqueous solutions of six other, generally more soluble, amino acids (alanine, arginine, glycine, hydroxyproline, lysine, and proline), of sucrose and sodium chloride. In general, L decreases approximately linearly with increasing solute concentration in these solutions. If we postulate that the observed decreases in gas solubility are due to hydration, the results under some assumptions can be used to calculate hydration numbers (H), i.e., the number of H2O molecules associated with each amino-acid solute molecule. The average values of hydration number (H¯) obtained at 25.0 °C are 15.3±1.5 for asparagine, 6.8±0.3 for cysteine, 11.5±1.1 for glutamine, 7.3±0.7 for histidine, 5.9±0.4 for isoleucine, 10.6±0.8 for methionine, 11.2±1.3 for serine, 7.7± 1.0 for threonine, and 6.6±0.6 for valine. We have also measured the temperature dependence of solubility L(T) from 5-40 °C for arginine, glycine, and proline, and obtained hydration numbers H¯(T) in this range. Between 25-40 °C, arginine has an H¯ near zero. This may be evidence for an attractive interaction between xenon and arginine molecules in aqueous solution.

Microstructure, magnetic and Moessbauer studies on spark-plasma sintered Sm-Co-Fe/Fe(Co) nanocomposite magnets

Energy Technology Data Exchange (ETDEWEB)

Rao, N V Rama; Saravanan, P; Gopalan, R; Raja, M Manivel; Rao, D V Sreedhara; Chandrasekaran, V [Defence Metallurgical Research Laboratory, Hyderabad-500 058 (India); Sivaprahasam, D [International Advanced Research Centre for Powder Metallurgy and New Materials Hyderabad-500 005 (India); Ranganathan, R [Saha Institute of Nuclear Physics, Kolkata-700 064 (India)], E-mail: rg_gopy@yahoo.com

2008-03-21

Nanocomposite powders comprising Sm-Co-Fe intermetallic phases and Fe(Co) were synthesized by high-energy ball milling and were consolidated into bulk magnets by the spark-plasma sintering (SPS) technique. While the microstructure of the SPS samples was characterized by transmission electron microscopy (TEM), the solubility of Fe in different phases was investigated using Moessbauer spectroscopy. TEM studies revealed that the spark-plasma sintered sample has Sm(Co,Fe){sub 5} as a major phase with Sm{sub 2}(Co,Fe){sub 17}, Sm(Co,Fe){sub 2} and Fe(Co) as secondary phases. The size of the nanocrystalline grains of all these phases was found to be in the range 50-100 nm. The Moessbauer spectra of the as-milled powders exhibited two different subspectra: a sextet corresponding to the Fe phase and a broad sextet associated with the Fe(Co) phase; while that of the SPS sample showed four different subspectra: a sextet corresponding to Fe and other three sextets corresponding to the Fe(Co), Sm(Co,Fe){sub 5} and Sm{sub 2}(Co,Fe){sub 17} phases; these results are in accordance with the TEM observation. Recoil magnetization and reversible susceptibility measurements revealed magnetically single phase behaviour of the SPS magnets.

Molecular characterization of whey protein hydrolysate fractions with ferrous chelating and enhanced iron solubility capabilities.

Science.gov (United States)

O'Loughlin, Ian B; Kelly, Phil M; Murray, Brian A; FitzGerald, Richard J; Brodkorb, Andre

2015-03-18

The ferrous (Fe2+) chelating capabilities of WPI hydrolysate fractions produced via cascade membrane filtration were investigated, specifically 1 kDa permeate (P) and 30 kDa retentate (R) fractions. The 1 kDa-P possessed a Fe2+ chelating capability at 1 g L(-1) equivalent to 84.4 μM EDTA (for 30 kDa-R the value was 8.7 μM EDTA). Fourier transformed infrared (FTIR) spectroscopy was utilized to investigate the structural characteristics of hydrolysates and molecular interactions with Fe2+. Solid-phase extraction was employed to enrich for chelating activity; the most potent chelating fraction was enriched in histidine and lysine. The solubility of ferrous sulfate solutions (10 mM) over a range of pH values was significantly (Piron solubility was improved by 72% in the presence of the 1 kDa-P fraction following simulated gastrointestinal digestion (SGID) compared to control FeSO4·7H2O solutions.

Biomineralization associated with microbial reduction of Fe3+ and oxidation of Fe2+ in solid minerals

Science.gov (United States)

Zhang, G.; Dong, H.; Jiang, H.; Kukkadapu, R.K.; Kim, J.; Eberl, D.; Xu, Z.

2009-01-01

Iron-reducing and oxidizing microorganisms gain energy through reduction or oxidation of iron, and by doing so play an important role in the geochemical cycling of iron. This study was undertaken to investigate mineral transformations associated with microbial reduction of Fe3+ and oxidation of Fe2+ in solid minerals. A fluid sample from the 2450 m depth of the Chinese Continental Scientific Drilling project was collected, and Fe3+-reducing and Fe2+-oxidizing microorganisms were enriched. The enrichment cultures displayed reduction of Fe3+ in nontronite and ferric citrate, and oxidation of Fe2+ in vivianite, siderite, and monosulfide (FeS). Additional experiments verified that the iron reduction and oxidation was biological. Oxidation of FeS resulted in the formation of goethite, lepidocrocite, and ferrihydrite as products. Although our molecular microbiological analyses detected Thermoan-aerobacter ethanolicus as a predominant organism in the enrichment culture, Fe3+ reduction and Fe2+ oxidation may be accomplished by a consortia of organisms. Our results have important environmental and ecological implications for iron redox cycling in solid minerals in natural environments, where iron mineral transformations may be related to the mobility and solubility of inorganic and organic contaminants.

Molybdenum solubility in aluminium nitrate solutions

Energy Technology Data Exchange (ETDEWEB)

Heres, X.; Sans, D.; Bertrand, M.; Eysseric, C. [CEA, Centre de Marcoule, Nuclear Energy Division, DRCP, BP 17171, 30207 Bagnols-sur-Ceze Cedex (France); Brackx, E.; Domenger, R.; Excoffier, E. [CEA, Centre de Marcoule, Nuclear Energy Division, DTEC, BP 17171, 30207 Bagnols-sur-Ceze Cedex (France); Valery, J.F. [AREVA-NC, DOR/RDP, Paris - La Defense (France)

2016-07-01

For over 60 years, research reactors (RR or RTR for research testing reactors) have been used as neutron sources for research, radioisotope production ({sup 99}Mo/{sup 99m}Tc), nuclear medicine, materials characterization, etc... Currently, over 240 of these reactors are in operation in 56 countries. They are simpler than power reactors and operate at lower temperature (cooled to below 100 C. degrees). The fuel assemblies are typically plates or cylinders of uranium alloy and aluminium (U-Al) coated with pure aluminium. These fuels can be processed in AREVA La Hague plant after batch dissolution in concentrated nitric acid and mixing with UOX fuel streams. The aim of this study is to accurately measure the solubility of molybdenum in nitric acid solution containing high concentrations of aluminium. The higher the molybdenum solubility is, the more flexible reprocessing operations are, especially when the spent fuels contain high amounts of molybdenum. To be most representative of the dissolution process, uranium-molybdenum alloy and molybdenum metal powder were dissolved in solutions of aluminium nitrate at the nominal dissolution temperature. The experiments showed complete dissolution of metallic elements after 30 minutes long stirring, even if molybdenum metal was added in excess. After an induction period, a slow precipitation of molybdic acid occurs for about 15 hours. The data obtained show the molybdenum solubility decreases with increasing aluminium concentration. The solubility law follows an exponential relation around 40 g/L of aluminium with a high determination coefficient. Molybdenum solubility is not impacted by the presence of gadolinium, or by an increasing concentration of uranium. (authors)

Electrical resistivity of Y(Fe1-x Alx)2 in the spin glass concentration range

International Nuclear Information System (INIS)

Cunha, S.F. da; Souza, G.P. de; Takeushi, A.Y.

1986-01-01

The temperature dependence of the electrical resistivity of the Y(Fe 1-x Al x ) 2 system (0.125 ≤ x ≤ 0.25) was measured. This system exhibits a minimum at low temperatures for the concentration range where the phase diagram presents a spin glass-ferromagnetic transition. A negative temperature coefficient is observed at high temperatures for x > 0.18 and was attributed to the high value of the electrical resistivity in this concentration range. (Author) [pt

Electrochemical Studies of Interactions Between Fe(II/Fe(III and Amino Acids Using Ferrocene-Modified Carbon Paste Electrode

Directory of Open Access Journals (Sweden)

Vatrál Jaroslav

2014-12-01

Full Text Available The electrochemical behavior of an Fe(II/Fe(III redox couple in the presence of various selected amino acids has been studied using ferrocene-modified carbon paste electrode at pH = 7.4. Because of Fe(II/Fe(III solubility issues at physiological pH, ferrocene was used as a source of iron. Anodic oxidation of iron (pH = 7.2 occurred at 0.356 V and cathodic oxidation at 0.231 V, both vs Ag|AgCl. Treatment of the voltammetric data showed that it was a purely diffusion-controlled reaction with the involvement of one electron. After addition of amino acids, potential shifts and current changes can be observed on the voltammograms. Cyclic voltammetry experiments revealed the capability of amino acids to change the electrochemical behavior of the Fe(II/Fe(III redox couple.

Magnetic hyperthermia studies on water-soluble polyacrylic acid-coated cobalt ferrite nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Krishna Surendra, M. [Indian Institute of Technology Madras, Department of Physics, Nano Functional Materials Technology Centre, Materials Research Centre (India); Annapoorani, S. [Anna University of Technology, Department of Nanotechnology (India); Ansar, Ereath Beeran; Harikrishna Varma, P. R. [Sree Chitra Tirunal Institute for Medical Sciences and Technology, Bioceramics Laboratory (India); Ramachandra Rao, M. S., E-mail: msrrao@iitm.ac.in [Indian Institute of Technology Madras, Department of Physics, Nano Functional Materials Technology Centre, Materials Research Centre (India)

2014-12-15

We report on synthesis and hyperthermia studies in the water-soluble ferrofluid made of polyacrylic acid-coated cobalt ferrite (CoFe{sub 2}O{sub 4}) nanoparticles with different particle sizes. Magnetic nanoparticles were synthesized using co-precipitation method and particle size was varied as 6, 10, and 14 nm by varying the precursor to surfactant concentration. PAA surfactant bonding and surfactant thickness were studied by FTIR and thermogravimetric analysis. At room temperature, nanoparticles show superparamagnetism and saturation magnetization was found to vary from 33 to 44 emu/g with increase in the particle size from 6 to 14 nm, and this increase was attributed to the presence of a magnetic inert layer of 4 Å thick. Effect of particle size, concentration, and alternating magnetic field strength at 275 kHz on specific absorption rate were studied by preparing ferrofluids in deionized water at different concentrations. Ferrofluids at a concentration of 1.25 g/L, with 10 min of AMF exposure of strength ∼15.7 kA/m show stable temperatures ∼48, 58, and 68 °C with increase in the particle sizes 6, 10, and 14 nm. A maximum specific absorption rate of 251 W/g for ferrofluid with a particle size of 10 nm at 1.25 g/L, 15.7 kA/m, and 275 kHz was observed. Viability of L929 fibroblasts is measured by MTT assay cytotoxicity studies using the polyacrylic acid-coated CoFe{sub 2}O{sub 4} nanoparticles.

Solubility of Tc(IV) oxides

International Nuclear Information System (INIS)

Liu, D.J.; Fan, X.H.

2005-01-01

Full text of publication follows: The deep geological disposal of the high level radioactive wastes is expected to be a safer disposal method in most countries. The long-lived fission product 99 Tc is present in large quantities in nuclear wastes and its chemical behavior in aqueous solution is of considerable interest. Under the reducing conditions, expected to exist in a deep geological repository, it is generally predicted that technetium will be present as TcO 2 .nH 2 O. The solubility of Tc(IV) is used as a source term in performance assessment of radioactive waste repository. Technetium oxide was prepared by reduction of a technetate solution with Sn 2+ . The solubility of Tc(IV) oxide has been determined in simulated groundwater and re-distilled water under aerobic and anaerobic conditions. The effects of pH and CO 3 2- concentration of solution on solubility of Tc(IV) oxide were studied. The concentration of total technetium and Tc(IV) species in the solutions were periodically determined by separating the oxidized and reduced technetium species using a solvent extraction procedure and counting the beta activity of the 99 Tc with a liquid scintillation counter. The experimental results show that the rate of oxidation of Tc(IV) in simulated groundwater and re-distilled water is about (1.49∼1.86) x 10 -9 mol/(L.d) under aerobic conditions, but Tc(IV) in simulated groundwater and re-distilled water is not oxidized under anaerobic conditions. Under aerobic or anaerobic conditions the solubility of Tc(IV) oxide in simulated groundwater and re-distilled water is equal on the whole after centrifugation or ultrafiltration. The solubility of Tc(IV) oxide decreases with the increase of pH at pH 10 and is pH independent in the range 2 -8 to 10 -9 mol/L at 2 3 2- concentration. These data could be used to estimate the Tc(IV) solubility for cases where solubility limits transport of technetium in reducing environments of high-level waste repositories. (authors)

An assessment of the homogeneity of nano-crystalline Fe-Cu powders as studied by means of APT

Energy Technology Data Exchange (ETDEWEB)

Wille, Catharina, E-mail: cwille@ump.gwdg.de [Georg-August-University Goettingen, Institute for Materials Physics, Goettingen 37077 (Germany); Al-Kassab, Talaat [Georg-August-University Goettingen, Institute for Materials Physics, Goettingen 37077 (Germany); Choi, Pyuck-Pa [Korea Institute of Science and Technology, Nano-Materials Research Center, Seoul (Korea, Republic of); Kwon, Young-Soon [Research Center for Machine Parts and Materials Processing, University of Ulsan, Ulsan (Korea, Republic of); Kirchheim, Reiner [Georg-August-University Goettingen, Institute for Materials Physics, Goettingen 37077 (Germany)

2009-04-15

In this contribution the homogeneity of mechanically alloyed Fe-Cu powders for two different compositions (Fe-10 and Fe-2.5 at%Cu) has been systematically characterised by atom probe tomography. Since Fe-Cu exhibits the Invar effect, it is among the most attractive systems for technical application. Furthermore, this system is immiscible and characterised by a large positive heat of mixing. In combination with the widespread application and accessibility, this predestines Fe-Cu as a binary model alloy to elaborate the enforced nonequilibrium enhanced solubility for immiscible systems. Depending on the parameters composition and milling time, results on the extension of the solubility limit and on the homogeneity of the alloy are presented, discussed and compared to earlier works. Only for the alloy with lower Cu content and for the prolonged milling time of 50 h, chemical homogeneity of the sample as measured by the atom probe was fully reached on the nano-scale. For all other parameter combinations homogeneity could not be achieved, even for long milling times and for those samples that appear to be homogeneous via X-ray analysis. Moreover, impurities were determined, mostly stemming from the fabrication procedure. The arrangement and homogeneity of the most common impurity, oxygen, was evaluated from atom probe data for different samples. Thus, the local concentration, segregation effects and the distribution of impurities could be quantified on the nano-scale, depending on the different nominal compositions and processing parameters. Additionally, structural information could be gained employing transmission electron microscopy and diffraction measurements.

An assessment of the homogeneity of nano-crystalline Fe-Cu powders as studied by means of APT

International Nuclear Information System (INIS)

Wille, Catharina; Al-Kassab, Talaat; Choi, Pyuck-Pa; Kwon, Young-Soon; Kirchheim, Reiner

2009-01-01

In this contribution the homogeneity of mechanically alloyed Fe-Cu powders for two different compositions (Fe-10 and Fe-2.5 at%Cu) has been systematically characterised by atom probe tomography. Since Fe-Cu exhibits the Invar effect, it is among the most attractive systems for technical application. Furthermore, this system is immiscible and characterised by a large positive heat of mixing. In combination with the widespread application and accessibility, this predestines Fe-Cu as a binary model alloy to elaborate the enforced nonequilibrium enhanced solubility for immiscible systems. Depending on the parameters composition and milling time, results on the extension of the solubility limit and on the homogeneity of the alloy are presented, discussed and compared to earlier works. Only for the alloy with lower Cu content and for the prolonged milling time of 50 h, chemical homogeneity of the sample as measured by the atom probe was fully reached on the nano-scale. For all other parameter combinations homogeneity could not be achieved, even for long milling times and for those samples that appear to be homogeneous via X-ray analysis. Moreover, impurities were determined, mostly stemming from the fabrication procedure. The arrangement and homogeneity of the most common impurity, oxygen, was evaluated from atom probe data for different samples. Thus, the local concentration, segregation effects and the distribution of impurities could be quantified on the nano-scale, depending on the different nominal compositions and processing parameters. Additionally, structural information could be gained employing transmission electron microscopy and diffraction measurements.

Evaluation of Chemical and Mineralogical Transformation of Iron in Different Soils in Saturated and Field Capacity Conditions

Directory of Open Access Journals (Sweden)

M. Saadatpour Mogaddam

2016-09-01

Full Text Available Introduction: Redox potential is one of the most important factors affecting on the solubility of iron minerals in soil. Decreasing redox potential in soil reduces Fe3+ to Fe2+, thereby affecting on solubility of Fe minerals. Application of organic matter to soil under waterlogging condition, decrease redox potential and as a consequence, accelerate the transformation of Fe minerals. The objectives of this study were: 1- The effect of waterlogging on the soluble total Fe concentration and transformation of Fe minerals in different soil pH values. 2- The indirect effects of organic matter on solubility of Fe minerals by changing the redox potential of the soils. Materials and Methods: A study was conducted to determine the effects of redox potential on solubility of Fe and transformation of Fe minerals during the time. Four agricultural soils were selected from different regions of Iran. The soil samples were treated with 0 (Cand 2% (O alfalfa powder and then incubated for 12 weeks under 60% Field capacity (F and waterlogged conditions (S. Subsamples were taken after 1and 12 weeks of incubation and the redox potential, pH value, electrical conductivity (EC, soluble cations (such as Ca2+, Mg2+, K+ and Na+ and anions (such as Cl-, SO42-, PO43- and NO3- and soluble Fe concentrations in the subsamples were measured. Concentrations of Fe2+ and Fe3+ species in soil solution were also predicted using Visual MINTEQ speciation program. Mineralogical transformation of Fe minerals was also determined by X-ray diffraction (XRD technique. Results and Discussion: The results in 60% Field capacity condition showed that pH value by organic matter (alfalfa powder application (OF increased significantly (p≤ 0.05 in acid and neutral soils and decreased in calcareous soils when compared to the control (CF. Organic matter is usually capable of lowering pH of alkaline soils by releasing hydrogen ions associated with organic anions or by nitrification in an open

Determination of radionuclide solubility limits to be used in SR 97. Uncertainties associated to calculated solubilities

Energy Technology Data Exchange (ETDEWEB)

Bruno, J.; Cera, E.; Duro, L.; Jordana, S. [QuantiSci S.L., Barcelona (Spain); Pablo, J. de [DEQ-UPC, Barcelona (Spain); Savage, D. [QuantiSci Ltd., Henley-on-Thames (United Kingdom)

1997-12-01

The thermochemical behaviour of 24 critical radionuclides for the forthcoming SR97 PA exercise is discussed. The available databases are reviewed and updated with new data and an extended database for aqueous and solid species of the radionuclides of interest is proposed. We have calculated solubility limits for the radionuclides of interest under different groundwater compositions. A sensitivity analysis of the calculated solubilities with the composition of the groundwater is presented. Besides selecting the most likely solubility limiting phases, in this work we have used coprecipitation approaches in order to calculate more realistic solubility limits for minor radionuclides, such as Ra, Am and Cm. The comparison between the calculated solubilities and the concentrations measured in relevant natural systems (NA) and in spent fuel leaching experiments helps to assess the validity of the methodology used and to derive source term concentrations for the radionuclides studied. The uncertainties associated to the solubilities of the main radionuclides involved in the spent nuclear fuel have also been discussed in this work. The variability of the groundwater chemistry; redox conditions and temperature of the system have been considered the main factors affecting the solubilities. In this case, a sensitivity analysis has been performed in order to study solubility changes as a function of these parameters. The uncertainties have been calculated by including the values found in a major extent in typical granitic groundwaters. The results obtained from this analysis indicate that there are some radionuclides which are not affected by these parameters, i.e. Ag, Cm, Ho, Nb, Ni, Np, Pu, Se, Sm, Sn, Sr, Tc and U

Solubility Modeling of the Binary Systems Fe(NO3)3–H2O, Co(NO3)2–H2O and the Ternary System Fe(NO3)3–Co(NO3)2–H2O with the Extended Universal Quasichemical (UNIQUAC) Model

DEFF Research Database (Denmark)

Arrad, Mouad; Kaddami, Mohammed; Goundali, Bahija El

2016-01-01

Solubility modeling in the binary system Fe(NO3)3–H2O, Co(NO3)2–H2O and the ternary system Fe(NO3)3–Co(NO3)2–H2O is presented. The extended UNIQUAC model was applied to the thermodynamic assessment of the investigated systems. The model parameters obtained were regressed simultaneously using...... the available databank but with more experimental points, recently published in the open literature. A revision of previously published parameters for the cobalt ion and new parameters for the iron(III) nitrate system are presented. Based on this set of parameters, the equilibrium constants of hydrates...

Two sugar-rhodamine "turn-on" fluorescent probes for the selective detection of Fe3 +

Science.gov (United States)

Chen, Qing; Fang, Zhijie

2018-03-01

Two new sugar-rhodamine fluorescent probes (RDG1 and RDG2) have been synthesized and characterized by 1H NMR, 13C NMR and HRMS. Their UV-Vis, fluorescence spectra and fluorescence-response to Fe3 + are investigated and discussed. RDG1 had a very nice linear relationship between UV absorbance and Fe3 + concentration with the correlation coefficient as high as 0.997 and the detection limit is 3.46 × 10- 6 M. Upon the addition of Fe3 +, the spirolactam ring of RDG1 was opened and a 1:1 metal ligand complex was formed from Job's plot. The results showed that RDG1 can be used as an effective fluorescent probe for selective detection of Fe3 + in water. RDG2 was incorporated the well-known rhodamine group and a water-soluble D-glucose group within one molecule and can be used for detecting Fe3 + in natural water as a selective fluorescent sensor. The addition of Fe3 + into RDG2 resulted in a strongly enhanced fluorescence as well as color change of solution from colorless to pink. Job's plot of RDG2 indicated 1:1 stoichiometry of RDG2-Fe3 +. RDG2 can serve as a probe for Fe3 + between pH = 4.0 to 7.0 and it's detection limit is 2.09 × 10- 6 M. The OFF-ON fluorescent mechanisms of RDG1-Fe3 + and RDG2-Fe3 + are proposed.

Enhanced Iron Solubility at Low pH in Global Aerosols

Directory of Open Access Journals (Sweden)

Ellery D. Ingall

2018-05-01

Full Text Available The composition and oxidation state of aerosol iron were examined using synchrotron-based iron near-edge X-ray absorption spectroscopy. By combining synchrotron-based techniques with water leachate analysis, impacts of oxidation state and mineralogy on aerosol iron solubility were assessed for samples taken from multiple locations in the Southern and the Atlantic Oceans; and also from Noida (India, Bermuda, and the Eastern Mediterranean (Crete. These sampling locations capture iron-containing aerosols from different source regions with varying marine, mineral dust, and anthropogenic influences. Across all locations, pH had the dominating influence on aerosol iron solubility. When aerosol samples were approximately neutral pH, iron solubility was on average 3.4%; when samples were below pH 4, the iron solubility increased to 35%. This observed aerosol iron solubility profile is consistent with thermodynamic predictions for the solubility of Fe(III oxides, the major iron containing phase in the aerosol samples. Source regions and transport paths were also important factors affecting iron solubility, as samples originating from or passing over populated regions tended to contain more soluble iron. Although the acidity appears to affect aerosol iron solubility globally, a direct relationship for all samples is confounded by factors such as anthropogenic influence, aerosol buffer capacity, mineralogy and physical processes.

Study for material analogs of FeSb2: Material design for thermoelectric materials

Science.gov (United States)

Kang, Chang-Jong; Kotliar, Gabriel

2018-03-01

Using the ab initio evolutionary algorithm (implemented in uspex) and electronic structure calculations we investigate the properties of a new thermoelectric material FeSbAs, which is a material analog of the enigmatic thermoelectric FeSb2. We utilize the density functional theory and the Gutzwiller method to check the energetics. We find that FeSbAs can be made thermodynamically stable above ˜30 GPa. We investigate the electronic structure and thermoelectric properties of FeSbAs based on the density functional theory and compare with those of FeSb2. Above 50 K, FeSbAs has higher Seebeck coefficients than FeSb2. Upon doping, the figure of merit becomes larger for FeSbAs than for FeSb2. Another material analog FeSbP, was also investigated, and found thermodynamically unstable even at very high pressure. Regarding FeSb2 as a member of a family of compounds (FeSb2, FeSbAs, and FeSbP) we elucidate what are the chemical handles that control the gaps in this series. We also investigate solubility (As or P for Sb in FeSb2) we found As to be more soluble. Finally, we study a two-band model for thermoelectric properties and find that the temperature dependent chemical potential and the presence of the ionized impurities are important to explain the extremum in the Seebeck coefficient exhibited in experiments for FeSb2.

Accounting for genotype–by-environment interactions and non-additive genetic variation in genomic selection for water-soluble carbohydrate concentration in wheat

Science.gov (United States)

Abiotic stress tolerance traits are often complex and recalcitrant targets for conventional breeding improvement in many crop species. This study evaluated the potential of genomic selection to predict water-soluble carbohydrate concentration (WSCC), an important drought tolerance trait, in wheat un...

Spectrophotometric determination of dopamine hydrochloride in pharmaceutical, banana, urine and serum samples by potassium ferricyanide-Fe(III).

Science.gov (United States)

Guo, Li; Zhang, Yan; Li, Quanmin

2009-12-01

In the present work, we developed a simple, sensitive and inexpensive method to determine dopamine hydrochloride using potassium ferricyanide-Fe(III) by spectrophotometry. The results show that Fe(III) is deoxidized to Fe(II) by dopamine hydrochloride at pH 4.0, and then Fe(II) reacts with potassium ferricyanide to form a soluble prussian blue (KFe(III)[Fe(II)(CN)6]). The absorbance of this product was monitored over time using a spectrophotometer at an absorption maximum of 735 nm, and the amount of dopamine hydrochloride could be calculated based on the absorbance. A good linear relationship of the concentration of dopamine hydrochloride versus absorbance was observed, and a linear regression equation of A = 0.022 + 0.16921C (microg mL(-1)) was obtained. Moreover, the apparent molar absorption coefficient for the indirect determination of dopamine hydrochloride was 3.2 x 10(4) L mol(-1) cm(-1). This described method has been used to determine dopamine hydrochloride in pharmaceutical, banana, urine and serum samples with satisfactory results.

Statistical model and first-principles simulation on concentration of HenV cluster and He bubble formation in α-Fe and W

International Nuclear Information System (INIS)

Liu, Yue-Lin; Yu, Yang; Dai, Zhen-Hong

2015-01-01

Using first-principles calculations, we investigate the stabilities of He and He n -vacancy (He n V) clusters in α-Fe and W. Vacancy formation energies are 2.08 eV in α-Fe and 3.11 eV in W, respectively. Single He in both α-Fe and W prefers to occupy the tetrahedral interstitial site. We recalculated the He solution energy considering the effect of zero-point energy (ZPE). The ZPEs of He in α-Fe and W at the tetrahedral (octahedral) interstitial site are 0.072 eV (0.031 eV) and 0.078 eV (0.034 eV), respectively. The trapping energies of single He at vacancy in α-Fe and W are −2.39 eV and −4.55 eV, respectively. By sequentially adding He into vacancy, a monovacancy trap up to 10 He atoms distributing in the vacancy vicinity. Based on the above results combined with statistical model, we evaluate the concentrations of all relevant He n V clusters as a function of He chemical potential. The critical He n V concentration is found to be ∼10 −40 (atomic) at the critical temperature T = 600 K in α-Fe and T = 1600 K in W, respectively. Beyond the critical He n V concentrations, considerable He n V aggregate to form He n V m clusters. By further growing of He n V m , the He n V m clusters grow bigger resulting in the larger He bubble formation

Particle Size, Surface Area, and Amorphous Content as Predictors of Solubility and Bioavailability for Five Commercial Sources of Ferric Orthophosphate in Ready-To-Eat Cereal

Directory of Open Access Journals (Sweden)

Robin S. Dickmann

2016-03-01

Full Text Available Ferric orthophosphate (FePO4 has had limited use as an iron fortificant in ready-to-eat (RTE cereal because of its variable bioavailability, the mechanism of which is poorly understood. Even though FePO4 has desirable sensory properties as compared to other affordable iron fortificants, few published studies have well-characterized its physicochemical properties. Semi-crystalline materials such as FePO4 have varying degrees of molecular disorder, referred to as amorphous content, which is hypothesized to be an important factor in bioavailability. The objective of this study was to systematically measure the physicochemical factors of particle size, surface area, amorphous content, and solubility underlying the variation in FePO4 bioavailability. Five commercial FePO4 sources and ferrous sulfate were added to individual batches of RTE cereal. The relative bioavailability value (RBV of each iron source, determined using the AOAC Rat Hemoglobin Repletion Bioassay, ranged from 51% to 99% (p < 0.05, which is higher than typically reported. Solubility in dilute HCl accurately predicted RBV (R2 = 0.93, p = 0.008. Amorphous content measured by Dynamic Vapor Sorption ranged from 1.7% to 23.8% and was a better determinant of solubility (R2 = 0.91; p = 0.0002 than surface area (R2 = 0.83; p = 0.002 and median particle size (R2 = 0.59; p = 0.12. The results indicate that while solubility of FePO4 is highly predictive of RBV, solubility, in turn, is strongly linked to amorphous content and surface area. This information may prove useful for the production of FePO4 with the desired RBV.

Ab initio and atomic kinetic Monte Carlo modelling of segregation in concentrated FeCrNi alloys

International Nuclear Information System (INIS)

Piochaud, J.B.; Becquart, C.S.; Domain, C.

2013-01-01

Internal structure of pressurised water reactors are made of austenitic materials. Under irradiation, the microstructure of these concentrated alloys evolves and solute segregation on grain boundaries or irradiation defects such as dislocation loops are observed to take place. In order to model and predict the microstructure evolution, a multi-scale modelling approach needs to be developed, which starts at the atomic scale. Atomic Kinetic Monte Carlo (AKMC) modelling is the method we chose to provide an insight on defect mediated diffusion under irradiation. In that approach, we model the concentrated commercial steel as a FeCrNi alloy (γ-Fe 70 Cr 20 Ni 10 ). As no reliable empirical potential exists at the moment to reproduce faithfully the phase diagram and the interactions of the elements and point defects, we have adjusted a pair interaction model on large amount of DFT (Density Functional Theory) calculations. The point defect properties in the Fe 70 Cr 20 Ni 10 , and more precisely, how their formation energy depends on the local environment will be presented and some AKMC results on thermal non equilibrium segregation (TNES) and radiation induce segregation will be presented. The effect of Si on the segregation will also be discussed. Preliminary results show that it is the solute- grain boundaries interactions which drive TNES

Temporal variability in trace metal solubility in a paddy soil not reflected in uptake by rice (Oryza sativa L.).

Science.gov (United States)

Pan, Yunyu; Koopmans, Gerwin F; Bonten, Luc T C; Song, Jing; Luo, Yongming; Temminghoff, Erwin J M; Comans, Rob N J

2016-12-01

Alternating flooding and drainage conditions have a strong influence on redox chemistry and the solubility of trace metals in paddy soils. However, current knowledge of how the effects of water management on trace metal solubility are linked to trace metal uptake by rice plants over time is still limited. Here, a field-contaminated paddy soil was subjected to two flooding and drainage cycles in a pot experiment with two rice plant cultivars, exhibiting either high or low Cd accumulation characteristics. Flooding led to a strong vertical gradient in the redox potential (Eh). The pH and Mn, Fe, and dissolved organic carbon concentrations increased with decreasing Eh and vice versa. During flooding, trace metal solubility decreased markedly, probably due to sulfide mineral precipitation. Despite its low solubility, the Cd content in rice grains exceeded the food quality standards for both cultivars. Trace metal contents in different rice plant tissues (roots, stem, and leaves) increased at a constant rate during the first flooding and drainage cycle but decreased after reaching a maximum during the second cycle. As such, the high temporal variability in trace metal solubility was not reflected in trace metal uptake by rice plants over time. This might be due to the presence of aerobic conditions and a consequent higher trace metal solubility near the root surface, even during flooding. Trace metal solubility in the rhizosphere should be considered when linking water management to trace metal uptake by rice over time.

The solubility and site preference of Fe{sup 3+} in Li{sub 7−3x}Fe{sub x}La{sub 3}Zr{sub 2}O{sub 12} garnets

Energy Technology Data Exchange (ETDEWEB)

Rettenwander, D., E-mail: daniel.rettenwander@sbg.ac.at [Department of Materials Research and Physics, University of Salzburg, 5020 Salzburg (Austria); Geiger, C.A. [Department of Materials Research and Physics, University of Salzburg, 5020 Salzburg (Austria); Tribus, M.; Tropper, P. [Institute of Mineralogy and Petrography, Faculty of Geo- and Atmospheric Sciences, University of Innsbruck, Innrain 52, 6020 Innsbruck (Austria); Wagner, R.; Tippelt, G.; Lottermoser, W.; Amthauer, G. [Department of Materials Research and Physics, University of Salzburg, 5020 Salzburg (Austria)

2015-10-15

A series of Fe{sup 3+}-bearing Li{sub 7}La{sub 3}Zr{sub 2}O{sub 12} (LLZO) garnets was synthesized using solid-state synthesis methods. The synthetic products were characterized compositionally using electron microprobe analysis and inductively coupled plasma optical emission spectroscopy (ICP-OES) and structurally using X-ray powder diffraction and {sup 57}Fe Mössbauer spectroscopy. A maximum of about 0.25 Fe{sup 3+} pfu could be incorporated in Li{sub 7−3x}Fe{sub x}La{sub 3}Zr{sub 2}O{sub 12} garnet solid solutions. At Fe{sup 3+} concentrations lower than about 0.16 pfu, both tetragonal and cubic garnets were obtained in the synthesis experiments. X-ray powder diffraction analysis showed only a garnet phase for syntheses with starting materials having intended Fe{sup 3+} contents lower than 0.52 Fe{sup 3+} pfu. Back-scattered electron images made with an electron microprobe also showed no phase other than garnet for these compositions. The lattice parameter, a{sub 0}, for all solid-solution garnets is similar with a value of a{sub 0}≈12.98 Å regardless of the amount of Fe{sup 3+}. {sup 57}Fe Mössbauer spectroscopic measurements indicate the presence of poorly- or nano-crystalline FeLaO{sub 3} in syntheses with Fe{sup 3+} contents greater than 0.16 Fe{sup 3+} pfu. The composition of different phase pure Li{sub 7−3x}Fe{sub x}La{sub 3}Zr{sub 2}O{sub 12} garnets, as determined by electron microprobe (Fe, La, Zr) and ICP-OES (Li) measurements, give Li{sub 6.89}Fe{sub 0.03}La{sub 3.05}Zr{sub 2.01}O{sub 12}, Li{sub 6.66}Fe{sub 0.06}La{sub 3.06}Zr{sub 2.01}O{sub 12}, Li{sub 6.54}Fe{sub 0.12}La{sub 3.01}Zr{sub 1.98}O{sub 12}, and Li{sub 6.19}Fe{sub 0.19}La{sub 3.02}Zr{sub 2.04}O{sub 12}. The {sup 57}Fe Mössbauer spectrum of cubic Li{sub 6.54}Fe{sub 0.12}La{sub 3.01}Zr{sub 1.98}O{sub 12} garnet indicates that most Fe{sup 3+} occurs at the special crystallographic 24d position, which is the standard tetrahedrally coordinated site in garnet. Fe{sup 3+} in smaller

Synthesis of [Fe(Leq(Lax]n coordination polymer nanoparticles using blockcopolymer micelles

Directory of Open Access Journals (Sweden)

Christoph Göbel

2017-06-01

Full Text Available Spin-crossover compounds are a class of materials that can change their spin state from high spin (HS to low spin (LS by external stimuli such as light, pressure or temperature. Applications demand compounds with defined properties concerning the size and switchability that are maintained when the compound is integrated into composite materials. Here, we report the synthesis of [Fe(Leq(Lax]n coordination polymer (CP nanoparticles using self-assembled polystyrene-block-poly(4-vinylpyridine (PS-b-P4VP block copolymer (BCP micelles as template. Variation of the solvent (THF and toluene and the rigidity of the axial ligand Lax (Lax = 1,2-di(pyridin-4-ylethane (bpea, trans-1,2-di(pyridin-4-ylethene (bpee, and 1,2-di(pyridin-4-ylethyne (bpey; Leq = 1,2-phenylenebis(iminomethylidyne-bis(2,4-pentanedionato(2− allowed the determination of the preconditions for the selective formation of nanoparticles. A low solubility of the CP in the used solvent and a high stability of the Fe–L bond with regard to ligand exchange are necessary for the formation of composite nanoparticles where the BCP micelle is filled with the CP, as in the case of the [FeLeq(bpey]n@BCP. Otherwise, in the case of more flexible ligands or ligands that lead to high spin complexes, the formation of microcrystals next to the CP–BCP nanoparticles is observed above a certain concentration of [Fe(Leq(Lax]n. The core of the nanoparticles is about 45 nm in diameter due to the templating effect of the BCP micelle, independent of the used iron complex and [Fe(Leq(Lax]n concentration. The spin-crossover properties of the composite material are similar to those of the bulk for FeLeq(bpea]n@BCP while pronounced differences are observed in the case of [FeLeq(bpey]n@BCP nanoparticles.

Experimental constraints on gold and silver solubility in iron sulfides

Energy Technology Data Exchange (ETDEWEB)

Pal' yanova, Galina [Institute of Geology and Mineralogy, Siberian Branch of the Russian Academy of Sciences, 3, Koptyuga, Novosibirsk, 630090 (Russian Federation); Novosibirsk State University, Russia, 2, Pirogova, Novosibirsk, 630090 (Russian Federation); Mikhlin, Yuri [Institute of Chemistry and Chemical Technology, Siberian Branch of the Russian Academy of Sciences, Akademgorodok, 50/24, Krasnoyarsk, 660036 (Russian Federation); Kokh, Konstantin, E-mail: k.a.kokh@gmail.com [Institute of Geology and Mineralogy, Siberian Branch of the Russian Academy of Sciences, 3, Koptyuga, Novosibirsk, 630090 (Russian Federation); Novosibirsk State University, Russia, 2, Pirogova, Novosibirsk, 630090 (Russian Federation); Siberian Physical–Technical Institute of Tomsk State University, 1, Novosobornaya, Tomsk, 634050 (Russian Federation); Karmanov, Nick [Institute of Geology and Mineralogy, Siberian Branch of the Russian Academy of Sciences, 3, Koptyuga, Novosibirsk, 630090 (Russian Federation); Seryotkin, Yurii [Institute of Geology and Mineralogy, Siberian Branch of the Russian Academy of Sciences, 3, Koptyuga, Novosibirsk, 630090 (Russian Federation); Novosibirsk State University, Russia, 2, Pirogova, Novosibirsk, 630090 (Russian Federation)

2015-11-15

Experiments were performed to determine crystallization of Fe,S-melts (pyriti≿ and troilitic with molar ratio S/Fe ratios of 2 and 1, respectively) containing traces of gold and silver at (Ag/Au){sub wt} ratios varying from 10 to 0.1. The solid products were studied by optical microscopy, scanning electron microscopy, X-ray powder diffraction (XRD), microprobe analysis, and X-ray photoelectron spectroscopy (XPS) in order to reveal the concentration limits of “invisible” gold and silver in magmatic iron sulfides, and to determine the influence of sulfur on forms of precious metals in the Fe–S system with different Ag/Au ratios. Au–Ag phases do not form inclusions but instead concentrate on the grain boundaries in the synthetic pyrrhotite and troilite, while pyrite comprises micro- (1–5 μm) and macroinclusions of Au–Ag alloys and Au–Ag sulfides. In “pyriti≿” systems, the fineness of alloys increases from 650 to 970‰ and the composition of sulfides changes from acanthite (Ag{sub 2}S) to uytenbogaardtite (Ag{sub 3}AuS{sub 2}) and petrovskaite (AgAuS) as the Ag/Au ratio decreases. The concentrations of “invisible” precious metals revealed in troilite were 0.040 ± 0.013 wt.% Au and 0.079 ± 0.016 wt.% Ag. Measured concentrations in pyrite and pyrrhotite were <0.024 wt.% Au and <0.030 wt.% Ag. The surface layers of iron sulfides probed with XPS were enriched in the precious metals, and in silver relative to gold, especially in the systems with Fe/S = 1, probably, due to depletion of the metallic alloy surfaces with gold. Au- and Ag-bearing iron sulfides crystallized primarily from melts may be the source of redeposited phases in hydrothermal and hypergene processes. - Highlights: • The samples of Fe–S–Au–Ag system were synthesized. • Coupled solubility of gold and silver in iron sulfides was specified. • Ag–Au inclusions on surfaces of iron sulfides are likely to be enriched in silver. • Au–Ag sulfides can exist along with

Enhanced Al and Zn removal from coal-mine drainage during rapid oxidation and precipitation of Fe oxides at near-neutral pH

Science.gov (United States)

Burrows, Jill E.; Cravotta, Charles A.; Peters, Stephen C.

2017-01-01

Net-alkaline, anoxic coal-mine drainage containing ∼20 mg/L FeII and ∼0.05 mg/L Al and Zn was subjected to parallel batch experiments: control, aeration (Aer 1 12.6 mL/s; Aer 2 16.8 mL/s; Aer 3 25.0 mL/s), and hydrogen peroxide (H2O2) to test the hypothesis that aeration increases pH, FeII oxidation, hydrous FeIII oxide (HFO) formation, and trace-metal removal through adsorption and coprecipitation with HFO. During 5.5-hr field experiments, pH increased from 6.4 to 6.7, 7.1, 7.6, and 8.1 for the control, Aer 1, Aer 2, and Aer 3, respectively, but decreased to 6.3 for the H2O2 treatment. Aeration accelerated removal of dissolved CO2, Fe, Al, and Zn. In Aer 3, dissolved Al was completely removed within 1 h, but increased to ∼20% of the initial concentration after 2.5 h when pH exceeded 7.5. H2O2 promoted rapid removal of all dissolved Fe and Al, and 13% of dissolved Zn.Kinetic modeling with PHREEQC simulated effects of aeration on pH, CO2, Fe, Zn, and Al. Aeration enhanced Zn adsorption by increasing pH and HFO formation while decreasing aqueous CO2 available to form ZnCO30 and Zn(CO3)22− at high pH. Al concentrations were inconsistent with solubility control by Al minerals or Al-containing HFO, but could be simulated by adsorption on HFO at pH oxidation with pH adjustment to ∼7.5 could be effective for treating high-Fe and moderate-Zn concentrations, whereas chemical oxidation without pH adjustment may be effective for treating high-Fe and moderate-Al concentrations.

Electrical resistivity surface for FeO-Fe2O3-P2O5 glasses

Science.gov (United States)

Vaughan, J. G.; Kinser, D. L.

1975-01-01

The dc electrical properties and microstructure of x(FeO-Fe2O3)-(100-x)P2O5 glasses were investigated up to a maximum of x = 75 mol %. Results indicate that, in general, the minimum resistivity of the glass does not occur at equal Fe(2+) and Fe(3+) concentrations, although for the special case where x = 55 mol % the minimum does occur at Fe(2+)/Fe total = 0.5, as reported by other investigators. Evidence presented shows that the position of the minimum resistivity is a function of total iron content. The minimum shifts to glasses richer in Fe(2+) at higher total iron concentrations.

Spatial Gradients in Trace Metal Concentrations in the Surface Microlayer of the Mediterranean Sea

Directory of Open Access Journals (Sweden)

Antonio eTovar-Sanchez

2014-12-01

Full Text Available The relationship between dust deposition and surface water metal concentrations is poorly understood. Dissolution, solubility, and partitioning reactions of trace metals from dust particles are governed by complex chemical, biological, and physical processes occurring in the surface ocean. Despite that, the role of the sea surface microlayer (SML, a thin, but fundamental component modulating the air-sea exchange of materials has not been properly evaluated. Our study revealed that the SML of the Mediterranean Sea is enriched with bioactive trace metals (i.e., Cd, Co, Cu and Fe, ranging from 8 (for Cd to 1000 (for Fe times higher than the dissolved metal pool in the underlying water column. The highest enrichments were spatially correlated with the atmospheric deposition of mineral particles. Our mass balance results suggest that the SML in the Mediterranean Sea contains about 2 tonnes of Fe. However, we did not detect any trends between the concentrations of metals in SML with the subsurface water concentrations and biomass distributions. These findings suggest that future studies are needed to quantify the rate of metal exchange between the SML and the bioavailable pool and that the SML should be considered to better understand the effect of atmospheric inputs on the biogeochemistry of trace metals in the ocean.

Bio-transformation and stabilization of arsenic (As) in contaminated soil using arsenic oxidizing bacteria and FeCl3 amendment.

Science.gov (United States)

Karn, Santosh Kumar; Pan, Xiangliang; Jenkinson, Ian R

2017-05-01

A combination of biological and chemical methods was applied in the present study to evaluate the removal of arsenic (As) from contaminated soil. The treatment involved As-oxidizing microbes aimed of transforming the more toxic As (III) to less toxic As (V) in the soil. FeCl 3 was added at three different concentrations (1, 2, and 3%) to stabilize the As (V). Leaching of the treated soil was investigated by making a soil column and passing tap water through it to determine solubility. Experimental results indicated that the bacterial activity had a pronounced positive effect on the transformation of As, and decreased the soluble exchangeable fraction from 50 to 0.7 mg/kg as compared to control and from 50 to 44 mg/kg after 7 days of treatment. FeCl 3 also played an indispensable role in the adsorption/stabilization of As in the soil; 1 and 2% FeCl 3 strongly influenced the adsorption of As (V). The soil leachate contained negligible amount of As and trace metals, which indicates that combining an efficient microbe with a chemical treatment is very effective route for the removal and stabilization of As from contaminated soil in the environment.

Thermodynamic model for solution behavior and solid-liquid equilibrium in Na-Al(III-Fe(III-Cr(III-Cl-H2O system at 25°C

Directory of Open Access Journals (Sweden)

André Laurent

2018-03-01

Full Text Available The knowledge of the thermodynamic behavior of multicomponent aqueous electrolyte systems is of main interest in geo-, and environmental-sciences. The main objective of this study is the development of a high accuracy thermodynamic model for solution behavior, and highly soluble M(IIICl3(s (M= Al, Fe, Cr minerals solubility in Na-Al(III-Cr(III-Fe(III-Cl-H2O system at 25°C. Comprehensive thermodynamic models that accurately predict aluminium, chromium and iron aqueous chemistry and M(III mineral solubilities as a function of pH, solution composition and concentration are critical for understanding many important geochemical and environmental processes involving these metals (e.g., mineral dissolution/alteration, rock formation, changes in rock permeability and fluid flow, soil formation, mass transport, toxic M(III remediation. Such a model would also have many industrial applications (e.g., aluminium, chromium and iron production, and their corrosion, solve scaling problems in geothermal energy and oil production. Comparisons of solubility and activity calculations with the experimental data in binary and ternary systems indicate that model predictions are within the uncertainty of the data. Limitations of the model due to data insufficiencies are discussed. The solubility modeling approach, implemented to the Pitzer specific interaction equations is employed. The resulting parameterization was developed for the geochemical Pitzer formalism based PHREEQC database.

Thermodynamic model for solution behavior and solid-liquid equilibrium in Na-Al(III)-Fe(III)-Cr(III)-Cl-H2O system at 25°C

Science.gov (United States)

André, Laurent; Christov, Christomir; Lassin, Arnault; Azaroual, Mohamed

2018-03-01

The knowledge of the thermodynamic behavior of multicomponent aqueous electrolyte systems is of main interest in geo-, and environmental-sciences. The main objective of this study is the development of a high accuracy thermodynamic model for solution behavior, and highly soluble M(III)Cl3(s) (M= Al, Fe, Cr) minerals solubility in Na-Al(III)-Cr(III)-Fe(III)-Cl-H2O system at 25°C. Comprehensive thermodynamic models that accurately predict aluminium, chromium and iron aqueous chemistry and M(III) mineral solubilities as a function of pH, solution composition and concentration are critical for understanding many important geochemical and environmental processes involving these metals (e.g., mineral dissolution/alteration, rock formation, changes in rock permeability and fluid flow, soil formation, mass transport, toxic M(III) remediation). Such a model would also have many industrial applications (e.g., aluminium, chromium and iron production, and their corrosion, solve scaling problems in geothermal energy and oil production). Comparisons of solubility and activity calculations with the experimental data in binary and ternary systems indicate that model predictions are within the uncertainty of the data. Limitations of the model due to data insufficiencies are discussed. The solubility modeling approach, implemented to the Pitzer specific interaction equations is employed. The resulting parameterization was developed for the geochemical Pitzer formalism based PHREEQC database.

Investigation of the 600 C isothermal section of the Fe-Al-Ce ternary system

Energy Technology Data Exchange (ETDEWEB)

Zheng, Huiyun; Yin, Fucheng [Xiangtan Univ., Hunan (China). School of Materials Science and Engineering; Xiangtan Univ., Hunan (China). Key Laboratory of Materials Design and Preparation Technology of Hunan Province; Li, Zhi [Xiangtan Univ., Hunan (China). School of Materials Science and Engineering; Xiangtan Univ., Hunan (China). Key Laboratory of Materials Design and Preparation Technology of Hunan Province; Xiangtan Univ., Hunan (China). Key Laboratory of Key Film Materials and Application for Equipment (Hunan province); Ji, Li [South China University of Technology, Guangdong (China). School of Materials Science and Engineering

2017-01-15

The isothermal section of the Fe-Al-Ce system at 600 C was determined by means of scanning electron microscopy coupled with energy dispersive spectroscopy and X-ray powder diffraction. Twenty three-phase regions were confirmed experimentally, and two three-phase regions could be deduced in this section. Five ternary compounds, i. e., τ{sub 1}, τ{sub 2}, τ{sub 3}, τ{sub 5}, and τ{sub 6}, exist at 600 C. The Fe{sub 2}Ce phase contains 6.6 at.% Al in the Fe-Al-Ce system. The Fe solubility in α-Al, αAl{sub 11}Ce{sub 3}, αAl{sub 3}Ce, Al{sub 2}Ce, AlCe, and AlCe{sub 3} is approximately 1.7 at.%, 1.1 at.%, 1.2 at.%, 1.3 at.%, 5.8 at.%, and 0.1 at.%, respectively, and the solubility of Ce in α-Al, FeAl{sub 3}, Fe{sub 2}Al{sub 5}, FeAl{sub 2}, and FeAl is approximately 0.1 at.%, 1.2 at.%, 1.9 at.%, 0.9 at.%, and 3.7 at.%, respectively.

The Impact of Fe-Ti Oxide Concentration on the Structural Rigidity of the Lower Oceanic Crust, Atlantis Bank, Southwest Indian Ridge

Science.gov (United States)

Deans, J. R.; Winkler, D. A.

2017-12-01

Fe-Ti oxides are important components of oceanic core complexes (OCC) formed at slow-spreading ridges, since Fe-Ti oxide phases form throughout the crustal column and are weaker than silicate phases. This study investigated the predicted relationship between the presence and concentration of Fe-Ti oxides and the presence/intensity of crystal-plastic deformation in samples from Atlantis Bank, Southwest Indian Ridge (SWIR). Atlantis Bank is an OCC that formed through the exhumation of lower oceanic crust along a detachment shear zone/fault. OCCs form along slow-spreading ridges and are characterized by the complex interactions between magmatism and crustal extension, thus, making them more susceptible to crystal-plastic deformation at higher temperatures and for weaker phases like Fe-Ti oxides to preferentially partition strain. Atlantis Bank has been the focus of many scientific expeditions to various sites including; Ocean Drilling Program (ODP) Holes 735B and 1105A, and the International Oceanic Discovery Program (IODP) Hole U1473A. A total of 589 thin sections from all three holes were analyzed using the software package Fiji to calculate the Fe-Ti oxide concentration within the thin sections. The Fe-Ti oxide percentage was correlated with the crystal-plastic fabric (CPF) intensity, from 0-5 (no foliation - ultramylonite), for each thin section using the statistical software R. All three holes show a positive correlation between the abundance of Fe-Ti oxides and the CPF intensity. Specifically, 76.3% of samples with a concentration of 5% or more Fe-Ti oxides have a corresponding CPF intensity value of 2 or more (porphyroclastic foliation - ultramylonitic). The positive correlation may be explained by the Fe-Ti oxides preferentially partitioning strain, especially at temperatures below where dry plagioclase can recrystallize. This allows for a mechanism of continued slip along the shear zone or form new shear zones at amphibolite grade conditions while the lower

The Effect of Nitrate Levels and Harvest Times on Fe, Zn, Cu, and K, Concentrations and Nitrate Reductase Activity in Lettuce and Spinach

Directory of Open Access Journals (Sweden)

Z. Gheshlaghi

2015-09-01

Full Text Available Leafy vegetables are considered as the main sources of nitrate in the human diet. In order to investigate the effect of nitrate levels and harvest times on nitrate accumulation, nitrate reductase activity, concentrations of Fe, Zn, Cu and K in Lettuce and Spinach and their relation to nitrate accumulation in these leafy vegetables, two harvest times (29 and 46 days after transplanting, two vegetable species of lettuce and spinach and two concentrations of nitrate (10 and 20 mM were used in a hydroponics greenhouse experiment with a completely randomized design and 3 replications. Modified Hoagland and Arnon nutrient solutions were used for the experiment. The results indicated that by increasing nitrate concentration of solution, nitrate accumulation in roots and shoots of lettuce and spinach increased significantly (P ≤ 0.05, and the same trend was observed for the nitrate reductase activity in the shoots of the two species. Increasing the nitrate concentrations of solution, reduced the shoot dry weight and the concentration of Fe and Cu in both species, where as it increased the K and Zn concentrations in the shoots of the two species in each both harvest times, the nitrate accumulation increased, but the nitrate reductase activity decreased in the shoots of the two species over the course of the growth. The Concentration of Fe, Cu and K decreased in the shoots of lettuce and the spinach with the time, despite the increase in Zn concentration in the shoots. The results also indicated that increasing nitrate concentrations of solution to the levels greater than the plant capacity for reduction and net uptake of nitrate, leads to the nitrate accumulation in the plants. Nitrate accumulation in plant tissue led to decreases in fresh shoot yield and Fe and Cu concentrations and nitrate reductase activities in both lettuce and spinach.

Heavy metals and organic pollutants in soils. Concentrations - sorption and solubility - effects on micro-organisms; Schwermetalle und organische Schadstoffe in Boeden. Gehalte - Sorption und Loeslichkeit - Wirkung auf Mikroorganismen

Energy Technology Data Exchange (ETDEWEB)

Welp, G.

2000-07-01

The thesis comprises six manuscripts published in different journals. Soil protection being the main theme the articles deal with different aspects that represent a necessary scientific basis of a risk assessment for polluted soils. The first step is to look at the total contents of different soil contaminants and to decide whether a pollution is given or not. In chapter II the contents of 18 elements in 335 soil samples of North Rhine-Westphalia are analysed, in order to determine groups of soil samples that are characterized by a certain range of element contents in connection with other common features (e.g., parent material, sampling region, specific source of pollution). The study bases on a detailed inspection of frequency distributions which are evaluated with a parametric method (assuming several single lognormal distributions) and with a nonparametric approach (Kemel density estimation). The latter method proved to be a useful tool to derive background concentrations for toxic elements in soils. It is necessary to differentiate between soluble (mobile, available) and insoluble (immobile, strongly adsorbed, precipitated) fractions of pollutants in soil. The sorption and solubility of pollutants in soils, therefore, is a second important parameter for an appropriate risk assessment. Four papers (chapter III-VI) deal with this aspect. In chapter III sorption and solubility of ten metals in four soil samples is studied. The quantity-intensity relations of eight metals [except Cr(III) and Fe(III)] are governed by sorption and complexation procecces and can be fitted by Freundlich isotherms. In three further papers sorption and solubility experiments with inorganic and organic toxicants are combined with microbial tests in order to detect effects on microorganisms in relation to soil properties. The large data set of about 500 dose-response curves was also used to examine the general reaction patterns of heterogeneous microbial populations under chemical stress

Reduction and long-term immobilization of technetium by Fe(II) associated with clay mineral nontronite

International Nuclear Information System (INIS)

Jaisi, Deb P.; Dong, Hailiang; Plymale, Andrew E.; Fredrickson, Jim K.; Zachara, John M.; Heald, S.; Liu, Chongxuan

2009-01-01

99Tc is formed mostly during nuclear reactions and is released into the environment during weapons testing and inadvertent waste disposal. The long half-life, high environmental mobility (as Tc(VII)O4-) and its possible uptake into the food chain cause 99Tc to be a significant environmental contaminant. In this study, we evaluated the role of Fe(II) in biologically reduced clay mineral, nontronite (NAu-2), in reducing Tc(VII)O4- to poorly soluble Tc(IV) species as a function of pH and Fe(II) concentration. The rate of Tc(VII) reduction by Fe(II) in NAu-2 was higher at neutral pH (pH 7.0) than at acidic and basic pHs when Fe(II) concentration was low (< 1 mmol/g). The effect of pH, however, was insignificant at higher Fe(II) concentrations. The reduction of Tc(VII) by Fe(II) associated with NAu-2 was also studied in the presence of common subsurface oxidants including iron and manganese oxides, nitrate, and oxygen, to evaluate the effect of the oxidants on the enhancement and inhibition of Tc(VII) reduction, and reoxidation of Tc(IV). Addition of iron oxides (goethite and hematite) to the Tc(VII)-NAu-2 system, where Tc(VII) reduction was ongoing, enhanced reduction of Tc(VII), apparently as a result of re-distribution of reactive Fe(II) from NAu-2 to more reactive goethite/hematite surfaces. Addition of manganese oxides stopped further Tc(VII) reduction, and in case of K+-birnessite, it reoxidized previously reduced Tc(IV). Nitrate neither enhanced reduction of Tc(VII) nor promoted reoxidation of Tc(IV). Approximately 11% of Tc(IV) was oxidized by oxygen. The rate and extent of Tc(IV) reoxidation was found to strongly depend on the nature of the oxidants and concentration of Fe(II). When the same oxidants were added to aged Tc reduction products (mainly NAu-2 and TcO2nH2O), the extent of Tc(IV) reoxidation decreased significantly relative to fresh Tc(IV) products. Increasing NAu-2 concentration also resulted in the decreased extent of Tc(IV) reoxidation. The results

On the water-soluble organic nitrogen concentration and mass size distribution during the fog season in the Po Valley, Italy.

Science.gov (United States)

Montero-Martínez, Guillermo; Rinaldi, Matteo; Gilardoni, Stefania; Giulianelli, Lara; Paglione, Marco; Decesari, Stefano; Fuzzi, Sandro; Facchini, Maria Cristina

2014-07-01

The study of organic nitrogen gained importance in recent decades due to its links with acid rain, pollution, and eutrophication. In this study, aerosol and fog water samples collected from two sites in Italy during November 2011 were analyzed to characterize their organic nitrogen content. Organic nitrogen contributed 19-25% of the total soluble nitrogen in the aerosol and around 13% in fog water. The largest water soluble organic nitrogen concentrations in the PM1.2 fraction occurred during the diurnal period with mean values of 2.03 and 2.16 μg-N m(-3) (154 and 145 nmol-N m(-3)) at Bologna and San Pietro Capofiume (SPC), respectively. The mean PM10 WSON concentration during diurnal periods at SPC was 2.30 μg-N m(-3) (164 nmol-N m(-3)) while it was 1.34 and 0.82 μg-N m(-3) (95.7 and 58.5 nmol-N m(-3)) in the night and fog water samples, respectively. Aerosol mass distribution profiles obtained during fog changed significantly with respect to those estimated in periods without fog periods due to fog scavenging, which proved to be over 80% efficient. Linear correlations suggested secondary processes related to combustion and, to a lesser extent, biomass burning, as plausible sources of WSON. Regarding the inorganic nitrogen fraction, the results showed that ammonium was the largest soluble inorganic nitrogen component in the samples. Copyright © 2014 Elsevier B.V. All rights reserved.

The Effect of the Concentration of Oxidant, Cr(VI), on the Iron Oxidation in Saline Water

Science.gov (United States)

Ahn, H.; Jo, H. Y.; Ryu, J. H.; Koh, Y. K.

2014-12-01

Deep geological disposal is currently considered as the most appropriate method to isolate high level radioactive wastes (HLRWs) from the ecosystem. If groundwater seeps into underground disposal facilities, water molecules can be dissociated to radicals or peroxides, which can oxidize metal canisters and HLRWs. The oxidized radionuclides with a high solubility can be dissolved in the groundwater. Some dissolved radionuclides can act as oxidants. The continuous radiolysis of water molecules, which results from continuous seepage of groundwater, can enable the continuous production of the radioactive oxidants, resulting in an increase in concentration of oxidants. In this study, the effect of oxidant concentration on iron oxidation in the presence of salt was evaluated. Zero valent iron (ZVI) particles were reacted with Cr(VI) solutions with initial Cr(VI) concentrations ranged from 50 to 300 mg/L in reactors. The initial pH and NaCl concentration were fixed at 3 and 0.5 M, respectively. An increase in the initial Cr(VI) concentration caused an increase in the rate and extend of H2 gas production. The decrement of Cr(VI) was increased as the initial Cr(VI) concentration was increased. The penetration of H+ ions in the presence Cl- ions through the passive film on the ZVI particles caused the reaction between H+ ions and ZVI particles, producing H2 gas and Fe2+ ions. The passive film was damaged during the reaction due to the eruption of H2 gas or peptization by Cl- ions. The Fe2+ ions were reacted with Cr(VI) ions in the solution, producing Fe(III)-Cr(III) (oxy)hydroxides on the passive film of ZVI particles or in the solution as colloidal particles. The Fe(III)-Cr(III) (oxy)hydroxides tends to be precipitated as colloidal particles at a high Cr(VI) concentration and precipitated on the passive film at a low Cr(VI) concentration. The passive film was repaired or thickened by additional formation of Fe(III)-Cr(III) (oxy)hydroxides at a lower Cr(VI) concentration.

The effect of acute physical and mental stress on soluble cellular adhesion molecule concentration.

Science.gov (United States)

Crabb, E Blake; Franco, R Lee; Caslin, Heather L; Blanks, Anson M; Bowen, Mary K; Acevedo, Edmund O

2016-07-15

This study investigated the impact of acute physical and mental stress on serum concentrations of vascular cell adhesion molecule (VCAM)-1 and CX3CL1/fractalkine. Male volunteers (n=20; 21.3±0.55years of age) completed a graded treadmill test to exhaustion and a 20-minute mental stress task (Stroop Color-Word Test, mental arithmetic) on separate, non-consecutive days. Heart rate (HR) was measured at baseline and throughout exercise and mental stress. Blood was collected at baseline (PRE), immediately following (POST) and 30min after (POST30) exercise and mental stress. Soluble VCAM-1 and fractalkine were quantified in participant serum via enzyme-linked immunosorbent assays. Both treadmill exercise and the mental stress task significantly increased participant HR; although, exercise resulted in a substantially greater increase in participant HR compared to mental stress (197.82±11.99 vs. 38.67±3.10% [pstress task did not significantly alter serum VCAM-1 or fractalkine at any time point. In conclusion, maximal aerobic exercise results in a significant elevation of the soluble adhesion molecules VCAM-1 and fractalkine in the serum of adult males that does not occur following laboratory-induced mental stress. The findings of the current investigation may suggest a novel protective role for acute aerobic exercise in vascular health via exercise-induced CAM proteolysis. Copyright © 2016 Elsevier Inc. All rights reserved.

Gum arabic modified Fe3O4 nanoparticles cross linked with collagen for isolation of bacteria

Directory of Open Access Journals (Sweden)

Chittor Raghuraman

2010-12-01

Full Text Available Abstract Background Multifunctional magnetic nanoparticles are important class of materials in the field of nanobiotechnology, as it is an emerging area of research for material science and molecular biology researchers. One of the various methods to obtain multifunctional nanomaterials, molecular functionalization by attaching organic functional groups to nanomagnetic materials is an important technique. Recently, functionalized magnetic nanoparticles have been demonstrated to be useful in isolation/detection of dangerous pathogens (bacteria/viruses for human life. Iron (Fe based material especially FePt is used in the isolation of ultralow concentrations (2 cfu/ml of bacteria in less time and it has been demonstrated that van-FePt may be used as an alternative fast detection technique with respect to conventional polymerase chain reaction (PCR method. However, still further improved demonstrations are necessary with interest to biocompatibility and green chemistry. Herein, we report the synthesis of Fe3O4 nanoparticles by template medication and its application for the detection/isolation of S. aureus bacteria. Results The reduction of anhydrous Iron chloride (FeCl3 in presence of sodium borohydride and water soluble polyelectrolyte (polydiallyldimethyl ammonium chloride, PDADMAC produces black precipitates. The X-ray diffraction (XRD, XPS and TEM analysis of the precipitates dried at 373 K demonstrated the formation of nanocrystalline Fe3O4. Moreover, scanning electron microscopy (SEM showed isolated staphylococcous aureus (S. aureus bacteria at ultralow concentrations using collagen coated gum arabic modified iron oxide nanoparticles (CCGAMION. Conclusion We are able to synthesize nanocrystalline Fe3O4 and CCGAMION was able to isolate S. aureus bacteria at 8-10 cfu (colony forming units/ml within ~3 minutes.

Fermentation and complex enzyme hydrolysis for improving the total soluble phenolic contents, flavonoid aglycones contents and bio-activities of guava leaves tea.

Science.gov (United States)

Wang, Lu; Luo, You; Wu, Yanan; Liu, Yan; Wu, Zhenqiang

2018-10-30

There are both soluble and insoluble-bound forms of phenolics in tea-leaf products. In order to increase total soluble phenolics contents, guava leaves tea (GLT) was first fermented with Monascus anka and Saccharomyces cerevisiae, and then hydrolyzed with complex enzymes. The changes in phenolics profiles, antioxidant activities and inhibitory effect on α-glucosidase in processed GLT were investigated. Compared with the un-fermented GLT, fermentation and complex enzymatic processing (FE) significantly increased the total phenolics, total flavonoids, quercetin and kaempferol contents by 2.1, 2.0, 13.0 and 6.8 times, respectively. After the FE, a major proportion of phenolics existed in the soluble form. Quercetin was released in the highest amount among different phenolics. In addition, soluble phenolic extracts from GLT following FE exhibited a highest antioxidant activity and inhibitory effect on α-glucosidase. The paper suggested an improved method for processing GLT into high-value products rich in phenolics and flavonoids aglycones with enhanced health benefits. Copyright © 2018 Elsevier Ltd. All rights reserved.

Solubility study of Tc(IV) oxides

International Nuclear Information System (INIS)

Liu, D.J.; Fan, X.H.

2005-01-01

The deep geological disposal of the high level radioactive wastes is expected to be a safer disposal method in most countries. The long-lived fission product 99 Tc is present in large quantities in nuclear wastes and its chemical behavior in aqueous solution is of considerable interest. Under oxidizing conditions technetium exists as the anionic species TcO 4 - whereas under the reducing conditions, expected to exist in a deep geological repository, it is generally predicted that technetium will be present as TcO 2 ·nH 2 O. Hence, the mobility of Tc(IV) in reducing groundwater may be limited by the solubility of TcO 2 ·nH 2 O under these conditions. Due to this fact it is important to investigate the solubility of TcO 2 ·nH 2 O. The solubility determines the release of radionuclides from waste form and is used as a source term in radionuclide migration analysis in performance assessment of radioactive waste repository. Technetium oxide was prepared by reduction of a technetate solution with Sn 2 + . The solubility of Tc(IV) oxide has been determined in simulated groundwater and redistilled water under aerobic and anaerobic conditions. The effects of pH and CO 3 2- concentration of solution on solubility of Tc(IV) oxide were studied. The concentration of total technetium and Tc(IV) species in the solutions were periodically determined by separating the oxidized and reduced technetium species using a solvent extraction procedure and counting the beta activity of the 99 Tc with a liquid scintillation counter. The experimental results show that the rate of oxidation of Tc(IV) in simulated groundwater and redistilled water is about (1.49-1.86) x 10 -9 mol/(L·d) under aerobic conditions, but Tc(IV) in simulated groundwater and redistilled water is not oxidized under anaerobic conditions. Under aerobic or anaerobic conditions the solubility of Tc(IV) oxide in simulated groundwater and redistilled water is equal on the whole after centrifugation or ultrafiltration. The

Phosphorus runoff from waste water treatment biosolids and poultry litter applied to agricultural soils.

Science.gov (United States)

White, John W; Coale, Frank J; Sims, J Thomas; Shober, Amy L

2010-01-01

Differences in the properties of organic phosphorus (P) sources, particularly those that undergo treatment to reduce soluble P, can affect soil P solubility and P transport in surface runoff. This 2-yr field study investigated soil P solubility and runoff P losses from two agricultural soils in the Mid-Atlantic region after land application of biosolids derived from different waste water treatment processes and poultry litter. Phosphorus speciation in the biosolids and poultry litter differed due to treatment processes and significantly altered soil P solubility and dissolved reactive P (DRP) and bioavailable P (FeO-P) concentrations in surface runoff. Runoff total P (TP) concentrations were closely related to sediment transport. Initial runoff DRP and FeO-P concentrations varied among the different biosolids and poultry litter applied. Over time, as sediment transport declined and DRP concentrations became an increasingly important component of runoff FeO-P and TP, total runoff P was more strongly influenced by the type of biosolids applied. Throughout the study, application of lime-stabilized biosolids and poultry litter increased concentrations of soil-soluble P, readily desorbable P, and soil P saturation, resulting in increased DRP and FeO-P concentrations in runoff. Land application of biosolids generated from waste water treatment processes that used amendments to reduce P solubility (e.g., FeCl(3)) did not increase soil P saturation and reduced the potential for DRP and FeO-P transport in surface runoff. These results illustrate the importance of waste water treatment plant process and determination of specific P source coefficients to account for differential P availability among organic P sources.

Hydroxyl Radical Formation from HULIS and Fe(II) Interactions: Fulvic Acid-Fe(II) Complexes in Simulated and Human Lung Fluids

Science.gov (United States)

Gonzalez, D.

2017-12-01

Inhalation of fine particulate matter (PM2.5) has long been associated with adverse health outcomes. However, the causative agents and underlying mechanisms for these health effects have yet to be identified. One hypothesis is that PM2.5 deposited in the alveoli produce an excess of highly reactive radicals, leading to oxidative stress. The OH radical may be the most physiologically damaging, capable of oxidizing of lipids, proteins and DNA. Due to the variability and uncertainty in PM2.5 composition, the components that contribute to OH formation are not well understood. Soluble Fe is a component of PM2.5that produces OH under physiological conditions. Humic-like substances are water soluble organics found in biomass burning and tobacco smoke. Humic-like substances are capable of binding to Fe and enhancing OH formation, but this chemistry is not well understood. In this work, we use soil derived fulvic acid as a surrogate for Humic-like substances and investigate its effect on OH formation from Fe(II) under conditions relevant to the lungs. We use a fluorescent OH trapping probe, chemical kinetics and thermodynamic modeling to investigate OH formation from fulvic acid and Fe(II) dissolved in simulated and human lung fluids. In simulated lung fluid, we find that fulvic acid binds to Fe(II) and enhances the rate of key reactions that form OH. When fulvic acid is added to human lung fluids containing Fe(II), an enhancement of OH formation is observed. In human lung fluid, fulvic acid and metal binding proteins compete for Fe binding. These metal binding proteins are typically not found in simulated lung fluids. Results show that fulvic acid strongly binds Fe(II) and catalyzes key reactions that form OH in both simulated and human lung fluids. These results may help explain the role of Humic-like substances and Fe in oxidative stress and adverse health outcomes. Furthermore, we suggest that future studies employ simulated lung fluids containing metal binding proteins

From which soil metal fractions Fe, Mn, Zn and Cu are taken up by olive trees (Olea europaea L., cv. 'Chondrolia Chalkidikis') in organic groves?

Science.gov (United States)

Chatzistathis, T; Papaioannou, A; Gasparatos, D; Molassiotis, A

2017-12-01

Organic farming has been proposed as an alternative agricultural system to help solve environmental problems, like the sustainable management of soil micronutrients, without inputs of chemical fertilizers. The purposes of this study were: i) to assess Fe, Mn, Zn and Cu bioavailability through the determination of sequentially extracted chemical forms (fractions) and their correlation with foliar micronutrient concentrations in mature organic olive (cv. 'Chondrolia Chalkidikis') groves; ii) to determine the soil depth and the available forms (fractions) by which the 4 metals are taken up by olive trees. DTPA extractable (from the soil layers 0-20, 20-40 and 40-60 cm) and foliar micronutrient concentrations were determined in two organic olive groves. Using the Tessier fractionation, five fractions, for all the metals, were found: exchangeable, bound to carbonates (acid-soluble), bound to Fe-Mn oxides (reducible), organic (oxidizable), as well as residual form. Our results indicated that Fe was taken up by the olive trees as organic complex, mainly from the soil layer 40-60 cm. Manganese was taken up from the exchangeable fraction (0-20 cm); Zinc was taken up as organic complex from the layers 0-20 and 40-60 cm, as well as in the exchangeable form from the upper 20 cm. Copper was taken up from the soil layers 0-20 and 40-60 cm as soluble organic complex, and as exchangeable ion from the upper 20 cm. Our data reveal the crucial role of organic matter to sustain metal (Fe, Zn and Cu) uptake -as soluble complexes-by olive trees, in mature organic groves grown on calcareous soils; it is also expected that these data will constitute a thorough insight and useful tool towards a successful nutrient and organic C management for organic olive groves, since no serious nutritional deficiencies were found. Copyright © 2017 Elsevier Ltd. All rights reserved.

Experimental investigation of the phase equilibria in the Co-Fe-Ti ternary system

Energy Technology Data Exchange (ETDEWEB)

Yuan, Chaohui; Chen, Chong; Peng, Yingbiao; Du, Yong; Li, Kun [Central South Univ., State Key of Powder Metallurgy, Changsha (China); Lu, Xingxu [Central South Univ., State Key of Powder Metallurgy, Changsha (China); Central South Univ., School of Materials Science and Engineering, Changsha (China)

2015-08-15

Phase equilibria in the Co-Fe-Ti ternary system were investigated by means of the equilibrated alloy method with X-ray powder diffraction and electron probe microanalysis. No ternary compounds were found. The experimental results indicated the existence of seven two-phase and one three-phase regions at 600 C, five two-phase and two three-phase regions at 800 C, and six two-phase and two three-phase regions at 950 C. The solubility of Co in TiFe{sub 2} was determined to be larger than 54 at.% at all investigated temperatures, and the solubilities of Fe in TiCo{sub 3} and Ti{sub 2}Co showed an appreciable increase with increasing temperature. The three-phase equilibrium in the Ti-rich corner at 800 C was revealed to be ((β-Ti) + Ti(Fe, Co) + Ti{sub 2}Co) rather than ((α-Ti) + Ti(Fe, Co) + Ti{sub 2}Co) reported in previous investigations. Based on the experimental data obtained in the present work, three isothermal sections at 600, 800 and 950 C were established.

Accumulation of Fe oxyhydroxides in the Peruvian oxygen deficient zone implies non-oxygen dependent Fe oxidation

Science.gov (United States)

Heller, Maija I.; Lam, Phoebe J.; Moffett, James W.; Till, Claire P.; Lee, Jong-Mi; Toner, Brandy M.; Marcus, Matthew A.

2017-08-01

Oxygen minimum zones (OMZs) have been proposed to be an important source of dissolved iron (Fe) into the interior ocean. However, previous studies in OMZs have shown a sharp decrease in total dissolved Fe (dFe) and/or dissolved Fe(II) (dFe(II)) concentrations at the shelf-break, despite constant temperature, salinity and continued lack of oxygen across the shelf-break. The loss of both total dFe and dFe(II) suggests a conversion of the dFe to particulate form, but studies that have coupled the reduction-oxidation (redox) speciation of both dissolved and particulate phases have not previously been done. Here we have measured the redox speciation and concentrations of both dissolved and particulate forms of Fe in samples collected during the U.S. GEOTRACES Eastern tropical Pacific Zonal Transect (EPZT) cruise in 2013 (GP16). This complete data set allows us to assess possible mechanisms for loss of dFe. We observed an offshore loss of dFe(II) within the oxygen deficient zone (ODZ), where dissolved oxygen is undetectable, accompanied by an increase in total particulate Fe (pFe). Total pFe concentrations were highest in the upper ODZ. X-ray absorption spectroscopy revealed that the pFe maximum was primarily in the Fe(III) form as Fe(III) oxyhydroxides. The remarkable similarity in the distributions of total particulate iron and nitrite suggests a role for nitrite in the oxidation of dFe(II) to pFe(III). We present a conceptual model for the rapid redox cycling of Fe that occurs in ODZs, despite the absence of oxygen.

Serum concentrations of soluble (s)L- and (s)P-selectins in women with ovarian cancer.

Science.gov (United States)

Majchrzak-Baczmańska, Dominika B; Głowacka, Ewa; Wilczyński, Miłosz; Malinowski, Andrzej

2018-03-01

The aim of the study was to compare serum concentration of soluble L- and P-selectins in women with ovarian cancer (OC) and healthy controls, and to investigate sL- and sP-selectin levels with regard to clinical and pathological parameters. Correlation analysis was used to measure the following: sL- and sP-selectin concentration and Ca125; sP-selectin and platelet concentrations; and sL-selectin and serum leukocyte levels in women with OC. The study included 29 patients with OC and 23 healthy controls. Serum concentrations of sL- and sP-selectins were measured in all subjects. Routine diagnostic tests: CBC and USG (both groups) and Ca125 (study group) were performed. Significantly higher serum concentrations of sL- and sP-selectins were found in the study group as compared to controls. Lower levels of serum sL-selectin were observed in women with poorly-differentiated OC (G3) and advanced stages of the disease (FIGO III, IV), but the results were statistically insignificant. No statistically significant relationship was detected between sP-selectin serum concentration in women with OC and tumour differentiation, histological type, and stage of the disease. No significant correlation was found between sL- and sP-selectins and Ca125 levels. A weak correlation was found between serum concentration of sP-selectin in women with OC and platelet count. No statistically significant correlation was observed between sL-selectin concentration and serum leukocyte levels in women with OC. The analysis of sL- and sP-selectin concentrations may be a useful tool in the diagnosis of OC. The levels of sL-selectin decrease with disease progression.

Dynamic Solubility Limits in Nanosized Olivine LiFePO4

NARCIS (Netherlands)

Wagemaker, Marnix; Singh, Deepak P.; Borghols, Wouter J.H.; Lafont, Ugo; Haverkate, Lucas; Peterson, Vanessa K.; Mulder, Fokko M.

2011-01-01

Because of its stability, nanosized olivine LiFePO4 opens the door toward high-power Li-ion battery technology for large-scale applications as required for plug-in hybrid vehicles. Here, we reveal that the thermodynamics of first-order phase transitions in nanoinsertion materials is distinctly

Effect of MgO on compositions of the system CaO-Al2O3-Fe2O3. Solubility

Directory of Open Access Journals (Sweden)

Palomo, Ángel

1986-12-01

Full Text Available Five different compositions belonging to the equilibrium system CaO-Al2O3-Fe2O3 were dopep with a fixed quantity of MgO (6,5% wt. The compositions, which lie in different primary fields of crystallization and in different triangles of compatibility, were submitted to several thermal treatments. Each composition, which had previously been melted, originates in its solidification the aluminates and ferrites which are usual in the interstitial phase of clinker Portland, although they are in different microstructural arrangements. The effect of MgO on the generated microstructures has been shown. Also, the solubility of MgO on the aluminic and ferritic phases has been measured.CCinco composiciones diferentes pertenecientes al sistema de equilibrio CaO-Al2O3-Fe2O3 fueron dopadas con una cantidad fija de MgO (6,5%. Las cinco composiciones, que están situadas sobre diferentes campos primarios de cristalización y/o sobre diferentes triángulos de compatibilidad, fueron sometidas a varios tratamientos térmicos. Cada composición (previamente fundida origina en su solidificación los aluminatos y ferritos habituales en la fase intersticial del clinker portland, aunque ordenados en microestructuras diferentes. Se ha comprobado el efecto del MgO sobre las microestructuras generadas, así como su solubilidad en las fases alumínicas y ferríticas.

Increased concentrations of soluble CD40 ligand platelet in patients with primary antiphospholipidic syndrome.

Science.gov (United States)

Galicia López, Aida; Olguín Ortega, Lourdes; Saavedra, Miguel A; Méndez Cruz, René; Jimenez Flores, Rafael; García de la Peña, Maximiliano

2013-01-01

To determine the concentrations of sCD40L in patients with PAPS, and establish its association with the number of thrombosis. We included patients with PAPS and healthy controls of the same age and sex. For analysis, patients with PAPS were divided into 2 groups: 1) patients with 1 thrombosis, and 2) patients with >1 thrombosis. Soluble CD40L concentrations were determined by ELISA method. sCD40L concentrations were significantly higher in patients with PAPS compared with the controls (9.72 ng ± 11.23 ng/ml vs. 4.69 ± 4.04 ng/ml) (P=.04) There was no association between serum levels of sCD40L and the number of thrombosis (1 thrombosis: 9.81 ± 9.87 ng/ml vs 9.63 ± 12.75 ng/ml in ≥ 1thrombosis (P=.13). In women with pregnancy and abortions, (13 patients) concentrations of sCD40L were higher than in those patients without a history of abortion (26 patients) but without statically significant difference (12.11 ± 16.46 ng/ml vs. 8.80 ± 8.61 ng/ml) (P=.33). There was no correlation between levels of sCD40L and the total number of thrombosis. Patients with PAPS have higher concentrations of sCD40L compared with healthy subjects, although this is not associated with a greater number of thrombosis. Among patients with PAPS, there is a tendency to higher concentrations of sCD40L in women with pregnancy and history of abortion. Since the platelet is the main cellular source of sCD40L, is possible that this pathway plays a pathogenic role in patients with PAPS. Copyright © 2012 Elsevier España, S.L. All rights reserved.

Viscosity and Electrical Conductivity of Concentrated Solutions of Soluble Coffee

Czech Academy of Sciences Publication Activity Database

Sobolík, Václav; Žitný, R.; Tovčigrečko, Valentin; Delgado, M.; Allaf, K.

2002-01-01

Roč. 51, č. 2 (2002), s. 93-98 ISSN 0260-8774 Institutional research plan: CEZ:AV0Z4072921; CEZ:MSM 212200008 Keywords : coffee extract * soluble coffee * viscosity Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 1.085, year: 2002

Solubility of Meloxicam in Mixed Solvent Systems | Babu | Ethiopian ...

African Journals Online (AJOL)

The solubility of meloxicam is higher in phosphate buffer (pH 7.4) compared to water, probably due to ionization of the drug. The solubility of meloxicam is marginally enhanced in surfactant systems (Tween 80 and Brij 35) at concentrations higher than cmc, proving the micellar solubilization. Meloxicam solubility studies in ...

Suppression of aqueous corrosion of La(Fe{sub 0.88}Si{sub 0.12}){sub 13} by reducing dissolved oxygen concentration for high-performance magnetic refrigeration

Energy Technology Data Exchange (ETDEWEB)

Fujieda, S., E-mail: fujieda@tagen.tohoku.ac.jp; Fukamichi, K.; Suzuki, S.

2014-07-05

Highlights: • The aqueous corrosion of La(Fe{sub 0.88}Si{sub 0.12}){sub 13} and its suppression were investigated. • The lattice expansion after immersion was caused by the hydrogen absorption. • The itinerant-electron metamagnetic transition became indistinct after immersion. • The aqueous corrosion was suppressed by reducing the dissolved oxygen concentration. - Abstract: The itinerant-electron metamagnetic transition of La(Fe{sub 0.88}Si{sub 0.12}){sub 13} becomes indistinct after immersion in distilled-water containing about 8 ppm of the dissolved oxygen (DO) concentration because of aqueous corrosion. However, the aqueous corrosion of La(Fe{sub 0.88}Si{sub 0.12}){sub 13} is significantly suppressed by reducing the DO concentration. Thus, isothermal magnetic entropy change after immersion for 30 days in deaerated distilled-water with a DO concentration less than 0.1 ppm is larger than that after immersion for 5 days in distilled-water containing about 8 ppm of the DO concentration. Consequently, the reduction of the DO concentration is effective for preservation of the excellent magnetocaloric effects of La(Fe{sub 0.88}Si{sub 0.12}){sub 13} in an aqueous solution, which is a promising heat transfer fluid of room-temperature magnetic refrigeration.

Study of nitrogen solubility in multicomponent iron alloys at its pressure in gaseous phase up to 1000kPa

International Nuclear Information System (INIS)

Pomarin, Yu.M.; Grigorenko, G.M.; Latash, Yu.V.; Kanibolotskij, S.A.

1983-01-01

A facility in which metal is melted in a weighed state and nitrogen partical pressure during relting may be charge from 0 to 1000 kPa is developed to investigate nitrogen solubility is liquim metals and alloys. Investigation of nitrogen solubility was performed using samples of 03Kh25N5AM3 steel and Kh20N5, Kh20N10, Kh40N10, Kh40N20 alloys. Positive deflection of [N]=f(√Psub(Nsub(2))) dependence from the Henry law is shown to be observed in the Kh40N10 alloy in the 100-1000 kPa pressure range. In this case the vatue of positive deflection decreases with temperature growth and at T=2273 K nitrogen solubility in the alloy submits to the law of square root. An equation permitting to calculate nitrogen solubility in alloys of Fe-Cr-Ni and Fe-Cr-Mn systems in the 0 to 1000 kPa range of nitrogen partial pressures is obtained

Characterizing the production and retention of dissolved iron as Fe(II) across a natural gradient in chlorophyll concentrations in the Southern Drake Passage - Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Katherine Barbeau

2007-04-10

Recent mesoscale iron fertilization studies in the Southern Ocean (e.g. SOIREE, EisenEx, SOFeX) have demonstrated the importance of iron as a limiting factor for phytoplankton growth in these high nutrient, low-chlorophyll (HNLC) waters. Results of these experiments have demonstrated that factors which influence the biological availability of the iron supplied to phytoplankton are crucial in bloom development, longevity, and generation of carbon export flux. These findings have important implications for the future development of iron fertilization protocols to enhance carbon sequestration in high-latitude oceans. In particular, processes which lead to the mobilization and retention of iron in dissolved form in the upper ocean are important in promoting continued biological availability of iron. Such processes can include photochemical redox cycling, which leads to the formation of soluble reduced iron, Fe(II), within iron-enriched waters. Creation of effective fertilization schemes will thus require more information about Fe(II) photoproduction in Southern Ocean waters as a means to retain new iron within the euphotic zone. To contribute to our knowledge base in this area, this project was funded by DOE with a goal of characterizing the production and retention of dissolved Fe as Fe(II) in an area of the southern Drake Passage near the Shackleton Transverse Ridge, a region with a strong recurrent chlorophyll gradient which is believed to be a site of natural iron enrichment in the Southern Ocean. This area was the focus of a multidisciplinary NSF/OPP-funded investigation in February 2004 (OPP02-30443, lead PI Greg Mitchell, SIO/UCSD) to determine the influence of mesoscale circulation and iron transport with regard to the observed patterns in sea surface chlorophyll in the region near the Shackleton Transverse Ridge. A number of parameters were assessed across this gradient in order to reveal interactions between plankton community structure and iron distributions

Spectrophotometric speciation of Fe(II) and Fe(III) using hydrazone-micelle systems and flow injections

International Nuclear Information System (INIS)

Khojali, Inas Osman

1999-04-01

Two hydrazones were synthesised, namely salicylhyrazone (SH) and trihydroxyacetophenone (THAPH) were synthesised with the objective of developing a method for determining of Fe(II) and Fe(III) in the presence of each other and hence the total iron.those hydrazones were selected so as to combine the ability of phenolic compounds to complex Fe(III) ions and the complexing characteristics of hydrazones. The complexes of Fe(II) S H and Fe(III) S H as well those of Fe(II)-THAPH and Fe(III)-THAPH had shown maximum absorbance at λ=412 nm which was not not modified by presence of micelles i.e. sodium n-dodecyl sulphate (SDS) and n-hexa dodecyl pyridinium bromide. The maximum absorbance for all complexes takes place around a neutral pH. Generally, in addition, of n-hexa dodecylpyridinium bromide to fe(II)-SH and Fe(III)-SH absorbance of the complexes increases with increasing the concentration of the micelle. The effects of the addition of sodium n-dodecyle sulphate (SDS) to Fe(III)-SH is also studied. Generally, increasing the concentration of the micelle decrease the absorbance of the complexes. To study the effect of the presence of Fe(II) and Fe(III) on the determination of each other,mixtures of Fe(II)-SH and Fe(III)-SH are studied. However, the use of ascorbic acid as a reducing reagent for Fe(III) did not produce the needed results but non reducible results, which may be due to the masking effect of ascorbic acid and thus making the metal not available to the ligand. However, conversion of Fe(II) to Fe(III) prior to the determination was avoided as this requires the use of oxidant, which will oxidise the ligand as well. To establish the condition for the maximum absorbance of THAPH complexes, the effect of the base was investigated by using sodium and ammonium hydroxide. Generally, increasing the concentration of the base decreases the abosrbance. as expected, ammonium hydroxide produced positive results than sodium hydroxide. After establishing the optimum Fi

Enhancement of soluble CD28 levels in the serum of Graves' disease.

Science.gov (United States)

Sun, Zhongwen; Yi, Lixian; Tao, Hong; Huang, Jingfang; Jin, Zhenghong; Xiao, Yang; Feng, Caiyun; Sun, Jing

2014-01-01

Graves' disease is an autoimmune disease of the thyroid gland mediated by T cells. CD28, a member of costimulatory molecules, plays a pivotal role in regulating T-cell responses. Plasma-soluble CD28 is one form of CD28 in peripheral blood. To investigate the concentrations of soluble CD28 in patients with Graves' disease, we used a sensitive dual monoclonal antibody sandwich enzyme-linked immunosorbent assay (ELISA) to detect the soluble form of CD28. Our results suggested that mean concentrations of soluble CD28 in plasma of patients with Graves' disease were 1.79 ±1.52 ng/ml, and levels of soluble CD28 in healthy subjects were only 0.83 ±1.35 ng/ml. Concentrations of soluble CD28 detected in patients with Graves' disease were significantly higher than those of healthy subjects (p Graves' disease. Therefore, aberrant elevation of plasma-soluble CD28 in patients with Graves' disease may reflect the dysregulation of immune system, and may serve as a useful biomarker in Graves' disease diagnosis.

Data representing two separate LC-MS methods for detection and quantification of water-soluble and fat-soluble vitamins in tears and blood serum

Directory of Open Access Journals (Sweden)

Maryam Khaksari

2017-04-01

Full Text Available Two separate liquid chromatography (LC-mass spectrometry (MS methods were developed for determination and quantification of water-soluble and fat-soluble vitamins in human tear and blood serum samples. The water-soluble vitamin method was originally developed to detect vitamins B1, B2, B3 (nicotinamide, B5, B6 (pyridoxine, B7, B9 and B12 while the fat-soluble vitamin method detected vitamins A, D3, 25(OHD3, E and K1. These methods were then validated with tear and blood serum samples. In this data in brief article, we provide details on the two LC-MS methods development, methods sensitivity, as well as precision and accuracy for determination of vitamins in human tears and blood serum. These methods were then used to determine the vitamin concentrations in infant and parent samples under a clinical study which were reported in "Determination of Water-Soluble and Fat-Soluble Vitamins in Tears and Blood Serum of Infants and Parents by Liquid Chromatography/Mass Spectrometry DOI:10.1016/j.exer.2016.12.007 [1]". This article provides more details on comparison of vitamin concentrations in the samples with the ranges reported in the literature along with the medically accepted normal ranges. The details on concentrations below the limits of detection (LOD and limits of quantification (LOQ are also discussed. Vitamin concentrations were also compared and cross-correlated with clinical data and nutritional information. Significant differences and strongly correlated data were reported in [1]. This article provides comprehensive details on the data with slight differences or slight correlations.

Data representing two separate LC-MS methods for detection and quantification of water-soluble and fat-soluble vitamins in tears and blood serum.

Science.gov (United States)

Khaksari, Maryam; Mazzoleni, Lynn R; Ruan, Chunhai; Kennedy, Robert T; Minerick, Adrienne R

2017-04-01

Two separate liquid chromatography (LC)-mass spectrometry (MS) methods were developed for determination and quantification of water-soluble and fat-soluble vitamins in human tear and blood serum samples. The water-soluble vitamin method was originally developed to detect vitamins B 1 , B 2 , B 3 (nicotinamide), B 5 , B 6 (pyridoxine), B 7 , B 9 and B 12 while the fat-soluble vitamin method detected vitamins A, D 3 , 25(OH)D 3, E and K 1 . These methods were then validated with tear and blood serum samples. In this data in brief article, we provide details on the two LC-MS methods development, methods sensitivity, as well as precision and accuracy for determination of vitamins in human tears and blood serum. These methods were then used to determine the vitamin concentrations in infant and parent samples under a clinical study which were reported in "Determination of Water-Soluble and Fat-Soluble Vitamins in Tears and Blood Serum of Infants and Parents by Liquid Chromatography/Mass Spectrometry DOI:10.1016/j.exer.2016.12.007 [1]". This article provides more details on comparison of vitamin concentrations in the samples with the ranges reported in the literature along with the medically accepted normal ranges. The details on concentrations below the limits of detection (LOD) and limits of quantification (LOQ) are also discussed. Vitamin concentrations were also compared and cross-correlated with clinical data and nutritional information. Significant differences and strongly correlated data were reported in [1]. This article provides comprehensive details on the data with slight differences or slight correlations.

Cofortification of ferric pyrophosphate and citric acid/trisodium citrate into extruded rice grains doubles iron bioavailability through in situ generation of soluble ferric pyrophosphate citrate complexes.

Science.gov (United States)

Hackl, Laura; Cercamondi, Colin I; Zeder, Christophe; Wild, Daniela; Adelmann, Horst; Zimmermann, Michael B; Moretti, Diego

2016-05-01

Iron fortification of rice is a promising strategy for improving iron nutrition. However, it is technically challenging because rice is consumed as intact grains, and ferric pyrophosphate (FePP), which is usually used for rice fortification, has low bioavailability. We investigated whether the addition of a citric acid/trisodium citrate (CA/TSC) mixture before extrusion increases iron absorption in humans from FePP-fortified extruded rice grains. We conducted an iron absorption study in iron-sufficient young women (n = 20), in which each participant consumed 4 different meals (4 mg Fe/meal): 1) extruded FePP-fortified rice (No CA/TSC); 2) extruded FePP-fortified rice with CA/TSC added before extrusion (CA/TSC extruded); 3) extruded FePP-fortified rice with CA/TSC solution added after cooking and before consumption (CA/TSC solution); and 4) nonextruded rice fortified with a FeSO4 solution added after cooking and before consumption (reference). Iron absorption was calculated from erythrocyte incorporation of stable iron isotopes 14 d after administration. In in vitro experiments, we assessed the soluble and dialyzable iron from rice meals in which CA/TSC was added at different preparation stages and from meals with different iron:CA:TSC ratios. Fractional iron absorption was significantly higher from CA/TSC-extruded meals (3.2%) than from No CA/TSC (1.7%) and CA/TSC solution (1.7%; all P solubility and dialyzability were higher in CA/TSC-extruded rice than in rice with No CA/TSC and CA/TSC solution, and solubility increased with higher amounts of added CA and TSC in extruded rice. Iron bioavailability nearly doubled when CA/TSC was extruded with FePP into fortified rice, resulting in iron bioavailability comparable to that of FeSO4 We attribute this effect to an in situ generation of soluble FePP citrate moieties during extrusion and/or cooking because of the close physical proximity of FePP and CA/TSC in the extruded rice matrix. This trial was registered at

Sensitivity analysis of uranium solubility under strongly oxidizing conditions

International Nuclear Information System (INIS)

Liu, L.; Neretnieks, I.

1999-01-01

To evaluate the effect of geochemical conditions in the repository on the solubility of uranium under strongly oxidizing conditions, a mathematical model has been developed to determine the solubility, by utilizing a set of nonlinear algebraic equations to describe the chemical equilibria in the groundwater environment. The model takes into account the predominant precipitation-dissolution reactions, hydrolysis reactions and complexation reactions that may occur under strongly oxidizing conditions. The model also includes the solubility-limiting solids induced by the presence of carbonate, phosphate, silicate, calcium, and sodium in the groundwater. The thermodynamic equilibrium constants used in the solubility calculations are essentially taken from the NEA Thermochemical Data Base of Uranium, with some modification and some uranium minerals added, such as soddyite, rutherfordite, uranophane, uranyl orthophosphate, and becquerelite. By applying this model, the sensitivities of uranium solubility to variations in the concentrations of various groundwater component species are systematically investigated. The results show that the total analytical concentrations of carbonate, phosphate, silicate, and calcium in deep groundwater play the most important role in determining the solubility of uranium under strongly oxidizing conditions

Modelling reaustenitisation in Fe-C steels with concentration-dependent diffusivity of carbon

Directory of Open Access Journals (Sweden)

Mancini, R.

2002-12-01

Full Text Available A finite difference method used to model reaustenitisation from a ferrite/cementite mixture in Fe-C steels is presented in this paper. Concentration-dependent carbon diffusivity in austenite is taken into account in order to generalize our earlier numerical model. We select some parameters, such as cementite dissolution time, and compare their values as calculated by different approximations available in the literature (in particular at steady state for planar and spherical geometries. When the dependence of diffusivity on concentration or temperature is increased, the steady state approximation fails to predict correctly the above mentioned parameters and the use of numerical techniques becomes indispensable.

En este trabajo se presenta un método numérico de diferencias finitas para modelar la reaustenización en aceros Fe-C a partir de una distribución inicial de ferrita y cementita. Se tiene en cuenta la dependencia de la difusividad en la austenita con la concentración de carbono, a fin de generalizar el propio modelo numérico previo. Se han seleccionado algunos parámetros, como el tiempo de disolución de la cementita, para comparar los valores obtenidos en este caso con los calculados con diferentes aproximaciones (en particular con la de estado estacionario para los casos de geometrías plana y esférica. Los resultados obtenidos muestran que, cuando la difusividad depende fuertemente de la concentración, la aproximación de estado estacionario no predice correctamente los parámetros calculados y se hace imprescindible la aplicación de métodos numéricos.

Insights into the microstructural and physical properties of colloidal Fe:ZnSe nanocrystals

Energy Technology Data Exchange (ETDEWEB)

Xie, Ruishi, E-mail: rxie@foxmail.com [Analytical and Testing Center, Southwest University of Science and Technology, Mianyang 621010 (China); Li, Yuanli [Department of Materials, Southwest University of Science and Technology, Mianyang 621010 (China); Jiang, Linhai; Zhang, Xingquan [Analytical and Testing Center, Southwest University of Science and Technology, Mianyang 621010 (China)

2014-10-30

Highlights: • We present a facile and environmentally friendly protocol to fabricate Fe:ZnSe nanocrystals. • The microstructural and physical properties of Fe:ZnSe nanocrystals were systematically investigated. • The current synthesis is dramatically simple and highly reproducible, it will facilitate the commercial scale synthesis of highly luminescent water-soluble nanocrystals with surface functionality in the near future. - Abstract: Here, we present a facile and environmentally friendly synthetic protocol to fabricate highly luminescent and water-soluble Fe:ZnSe nanocrystals in aqueous solution at low temperature. The microstructure and various physical properties (e.g., crystal structure, interplanar spacing, lattice parameter, crystalline size, lattice microstrain, intrinsic stress, X-ray density, specific surface area, dislocation density, porosity, agglomeration number) of the Fe:ZnSe nanocrystals were systematically investigated using X-ray diffraction. The particle size and morphology of the Fe:ZnSe nanocrystals were determined by transmission electron microscopy. The optical properties (e.g., absorption and photoluminescence) of the fabricated nanocrystals were explored using ultraviolet–visible absorption and photoluminescence spectroscopies, respectively. The surface functionalization of the Fe:ZnSe nanocrystals by mercaptoacetic acid ligand was evidenced by Fourier transform infrared spectroscopy. To confirm the elementary composition of the obtained nanocrystals, Energy dispersive X-ray spectroscopy was performed. To further shed light upon elemental distribution of the resulting nanocrystals, elemental mapping measurements were conducted. Moreover, the underlying mechanisms were also elucidated. As a consequence, the current investigation not only provides a deep insight into exploring the physical properties of doped nanocrystals, but also demonstrates a useful synthetic strategy for producing water-soluble and highly fluorescent doped

Thermodynamic controls on the kinetics of microbial low-pH Fe(II) oxidation.

Science.gov (United States)

Larson, Lance N; Sánchez-España, Javier; Kaley, Bradley; Sheng, Yizhi; Bibby, Kyle; Burgos, William D

2014-08-19

Acid mine drainage (AMD) is a major worldwide environmental threat to surface and groundwater quality. Microbial low-pH Fe(II) oxidation could be exploited for cost-effective AMD treatment; however, its use is limited because of uncertainties associated with its rate and ability to remove Fe from solution. We developed a thermodynamic-based framework to evaluate the kinetics of low-pH Fe(II) oxidation. We measured the kinetics of low-pH Fe(II) oxidation at five sites in the Appalachian Coal Basin in the US and three sites in the Iberian Pyrite Belt in Spain and found that the fastest rates of Fe(II) oxidation occurred at the sites with the lowest pH values. Thermodynamic calculations showed that the Gibbs free energy of Fe(II) oxidation (ΔG(oxidation)) was also most negative at the sites with the lowest pH values. We then conducted two series of microbial Fe(II) oxidation experiments in laboratory-scale chemostatic bioreactors operated through a series of pH values (2.1-4.2) and found the same relationships between Fe(II) oxidation kinetics, ΔG(oxidation), and pH. Conditions that favored the fastest rates of Fe(II) oxidation coincided with higher Fe(III) solubility. The solubility of Fe(III) minerals, thus plays an important role on Fe(II) oxidation kinetics. Methods to incorporate microbial low-pH Fe(II) oxidation into active and passive AMD treatment systems are discussed in the context of these findings. This study presents a simplified model that describes the relationship between free energy and microbial kinetics and should be broadly applicable to many biogeochemical systems.

New method for simultaneous determination of Fe(II) and Fe(III) in water using flow injection technique

International Nuclear Information System (INIS)

Kozak, J.; Gutowski, J.; Kozak, M.; Wieczorek, M.; Koscielniak, P.

2010-01-01

The method exploits the possibilities of flow injection gradient titration in a system of reversed flow with spectrophotometric detection. In the developed approach a small amount of titrant (EDTA) is injected into a stream of sample containing a mixture of indicators (sulfosalicylic acid and 1,10-phenanthroline). In acid environment sulfosalicylic acid forms a complex with Fe(III), whereas 1,10-phenanthroline forms a complex with Fe(II). Measurements are performed at wavelength λ = 530 nm when radiation is absorbed by both complexes. After injection EDTA replaces sulfosalicylic acid and forms with Fe(III) more stable colourless complex. As a result, a characteristic 'cut off' peak is registered with a width corresponding to the Fe(III) concentration and with a height corresponding to the Fe(II) concentration. Calibration was performed by titration of four two-component standard solutions of the Fe(II)/Fe(III) concentrations established in accordance with 2 2 factorial plan. The method was tested with the use of synthetic samples and then it was applied to the analysis of water samples taken from artesian wells. Under optimized experimental conditions Fe(II) and Fe(III) were determined with precision less than 0.8 and 2.5% (RSD) and accuracy less than 3.2 and 5.1% (relative error) within the concentration ranges of 0.1-3.0 and 0.9-3.5 mg L -1 of both analytes, respectively.

Study of solubility of some metal cyclohexane carbonates

International Nuclear Information System (INIS)

Niyazov, A.N.; Amanov, K.B.; Trapeznikova, V.F.; Kul'maksimov, A.; Kolosova, N.

1978-01-01

The solubility of calcium, magnesium, strontium, barium, cabalt, copper and aluminium cyclohexane, carbonates (CHC) in water has been studied at 25 deg C. The salt solubility has been calculated according to the metal ion concentration in saturated solutions. It has been established, that the cobalt and rare earth cyclohexane carbonates are relatively very soluble in water and have solubility products of SP > 1x10 -5 . The solubility of CHC of multivalent metals increases with the decrease of pH values. Each salt has some ''limiting'' pH value of a solution, below which it decomposes completely and can not exist in a solution in the form of solid phase

Effects of different water storage procedures on the dissolved Fe concentration and isotopic composition of chemically contrasted waters from the Amazon River Basin.

Science.gov (United States)

Mulholland, Daniel S; Poitrasson, Franck; Boaventura, Geraldo R

2015-11-15

Although recent studies have investigated the Fe isotopic composition of dissolved, colloidal and particulate phases from continental and oceanic natural waters, few efforts have been made to evaluate whether water sample storage and the separation of different pore-size fractions through filtration can cause any change to the Fe isotopic compositions. The present study investigates the possible biases introduced by different water storage conditions on the dissolved Fe concentration and isotopic composition of chemically different waters. Water samples were collected from an organic-rich river and from mineral particulate-rich rivers. Filtered and unfiltered water samples were stored either at room temperature or frozen at -18°C in order to assess possible biases due to (i) different water storage temperature, and (ii) storage of bulk (unfiltered) vs filtered water. Iron isotope measurements were performed by Multicollector Inductively Coupled Plasma Mass Spectrometry with a Thermo Electron Neptune instrument, after Fe purification using anion-exchange resins. Our data reveal that bulk water storage at room temperature without filtration produces minor changes in the dissolved Fe isotopic composition of mineral particulate-rich waters, but significant isotopic composition changes in organic-rich waters. In both cases, however, the impact of the different procedures on the Fe concentrations was strong. On the other hand, the bulk water stored frozen without filtration produced more limited changes in the dissolved Fe concentrations, and also on isotopic compositions, relative to the samples filtered in the field. The largest effect was again observed for the organic-rich waters. These findings suggest that a time lag between water collection and filtration may cause isotopic exchanges between the dissolved and particulate Fe fractions. When it is not possible to filter the samples in the field immediately after collection, the less detrimental approach is to

The solubility and site preference of Fe3+ in Li7−3xFexLa3Zr2O12 garnets

International Nuclear Information System (INIS)

Rettenwander, D.; Geiger, C.A.; Tribus, M.; Tropper, P.; Wagner, R.; Tippelt, G.; Lottermoser, W.; Amthauer, G.

2015-01-01

A series of Fe 3+ -bearing Li 7 La 3 Zr 2 O 12 (LLZO) garnets was synthesized using solid-state synthesis methods. The synthetic products were characterized compositionally using electron microprobe analysis and inductively coupled plasma optical emission spectroscopy (ICP-OES) and structurally using X-ray powder diffraction and 57 Fe Mössbauer spectroscopy. A maximum of about 0.25 Fe 3+ pfu could be incorporated in Li 7−3x Fe x La 3 Zr 2 O 12 garnet solid solutions. At Fe 3+ concentrations lower than about 0.16 pfu, both tetragonal and cubic garnets were obtained in the synthesis experiments. X-ray powder diffraction analysis showed only a garnet phase for syntheses with starting materials having intended Fe 3+ contents lower than 0.52 Fe 3+ pfu. Back-scattered electron images made with an electron microprobe also showed no phase other than garnet for these compositions. The lattice parameter, a 0 , for all solid-solution garnets is similar with a value of a 0 ≈12.98 Å regardless of the amount of Fe 3+ . 57 Fe Mössbauer spectroscopic measurements indicate the presence of poorly- or nano-crystalline FeLaO 3 in syntheses with Fe 3+ contents greater than 0.16 Fe 3+ pfu. The composition of different phase pure Li 7−3x Fe x La 3 Zr 2 O 12 garnets, as determined by electron microprobe (Fe, La, Zr) and ICP-OES (Li) measurements, give Li 6.89 Fe 0.03 La 3.05 Zr 2.01 O 12 , Li 6.66 Fe 0.06 La 3.06 Zr 2.01 O 12 , Li 6.54 Fe 0.12 La 3.01 Zr 1.98 O 12 , and Li 6.19 Fe 0.19 La 3.02 Zr 2.04 O 12 . The 57 Fe Mössbauer spectrum of cubic Li 6.54 Fe 0.12 La 3.01 Zr 1.98 O 12 garnet indicates that most Fe 3+ occurs at the special crystallographic 24d position, which is the standard tetrahedrally coordinated site in garnet. Fe 3+ in smaller amounts occurs at a general 96h site, which is only present for certain Li-oxide garnets, and in Li 6.54 Fe 0.12 La 3.01 Zr 1.98 O 12 this Fe 3+ has a distorted 4-fold coordination. - Graphical abstract: Cubic nominally Li 7 La 3 Zr 2 O

Detection of colloidal silver chloride near solubility limit

Science.gov (United States)

Putri, K. Y.; Adawiah, R.

2018-03-01

Detection of nanoparticles in solution has been made possible by several means; one of them is laser-induced breakdown detection (LIBD). LIBD is able to distinguish colloids of various sizes and concentrations. This technique has been used in several solubility studies. In this study, the formation of colloids in a mixed system of silver nitrate and sodium chloride was observed by acoustic LIBD. Silver chloride has low solubility limit, therefore LIBD measurement is appropriate. Silver and chloride solutions with equal concentrations, set at below and above the solubility of silver chloride as the expected solid product, were mixed and the resulting colloids were observed. The result of LIBD measurement showed that larger particles were present as more silver and chloride introduced. However, once the concentrations exceeded the solubility limit of silver chloride, the detected particle size seemed to be decreasing, hence suggested the occurrence of coprecipitation process. This phenomenon indicated that the ability of LIBD to detect even small changes in colloid amounts might be a useful tool in study on formation and stability of colloids, i.e. to confirm whether nanoparticles synthesis has been successfully performed and whether the system is stable or not.

Effect of Atmospheric Organics on Bioavailable Fe Lifetime in the Oceans

Science.gov (United States)

Meskhidze, Nicholas; Hurley, David; Royalty, Taylor Michael; Johnson, Matthew S.

2016-01-01

The deposition of atmospheric aerosols is an important supply pathway of soluble iron (sol-Fe) to the global oceans influencing marine ecosystem processes and climate. Previous studies have shown that natural and anthropogenic acidic trace gases, when mixed with mineral dust, can lead to production of sol-Fe, leading to considerable increase in dust-Fe solubility. Recent studies have further highlighted the importance of atmospheric organic compounds/ligands in the production of sol-Fe during atmospheric transport and transformation of mineral aerosols. However, the actual scope of this aerosol sol-Fe for stimulating the primary productivity in the oceans is determined by both: the total atmospheric fluxes of sol-Fe and the lifetime of sol-Fe after its deposition to the ocean. In this study several atmospheric organic ligands were investigated for their effect on the lifetime of sol-Fe after mixing with seawater. Organic ligands were selected based on their abundance in the marine boundary layer and rainwater and their ability to form bidentate complexes with Fe. The results reveal that the tested organics had minor influence on Fe(II) lifetime in seawater. However, results also show that some organic acid considerably extended the lifetime of colloidal and aqueous Fe(III). Using these results we simulate aerosol sol-Fe lifetime in the ocean for different mineral dust deposition events in the presence and the absence of atmospheric organic ligands. The calculations suggest that when a large dust plume is assumed to contain Fe(II) alone, less than 15% of aerosol sol-Fe gets complexed with marine organic ligands. However, this fraction increases to over 90% when atmospheric Fe is allowed to bond with atmospheric organic acids prior to deposition to the oceans. Calculations also show that for the conditions when seawater organic ligands get titrated by Fe released from dust aerosol particles, retention of sol-Fe in the ocean depends on surface ocean mixing, i

Statistical model and first-principles simulation on concentration of He{sub n}V cluster and He bubble formation in α-Fe and W

Energy Technology Data Exchange (ETDEWEB)

Liu, Yue-Lin, E-mail: liuyuelin@ss.buaa.edu.cn; Yu, Yang; Dai, Zhen-Hong

2015-01-15

Using first-principles calculations, we investigate the stabilities of He and He{sub n}-vacancy (He{sub n}V) clusters in α-Fe and W. Vacancy formation energies are 2.08 eV in α-Fe and 3.11 eV in W, respectively. Single He in both α-Fe and W prefers to occupy the tetrahedral interstitial site. We recalculated the He solution energy considering the effect of zero-point energy (ZPE). The ZPEs of He in α-Fe and W at the tetrahedral (octahedral) interstitial site are 0.072 eV (0.031 eV) and 0.078 eV (0.034 eV), respectively. The trapping energies of single He at vacancy in α-Fe and W are −2.39 eV and −4.55 eV, respectively. By sequentially adding He into vacancy, a monovacancy trap up to 10 He atoms distributing in the vacancy vicinity. Based on the above results combined with statistical model, we evaluate the concentrations of all relevant He{sub n}V clusters as a function of He chemical potential. The critical He{sub n}V concentration is found to be ∼10{sup −40} (atomic) at the critical temperature T = 600 K in α-Fe and T = 1600 K in W, respectively. Beyond the critical He{sub n}V concentrations, considerable He{sub n}V aggregate to form He{sub n}V{sub m} clusters. By further growing of He{sub n}V{sub m}, the He{sub n}V{sub m} clusters grow bigger resulting in the larger He bubble formation.

Thorium oxalate solubility and morphology

International Nuclear Information System (INIS)

Monson, P.R. Jr.; Hall, R.

1981-10-01

Thorium was used as a stand-in for studying the solubility and precipitation of neptunium and plutonium oxalates. Thorium oxalate solubility was determined over a range of 0.001 to 10.0 in the concentration parameter [H 2 C 2 O 4 ]/[HNO 3 ] 2 . Morphology of thorium oxide made from the oxalate precipitates was characterized by scanning electron microscopy. The different morphologies found for oxalate-lean and oxalate-rich precipitations were in agreement with predictions based on precipitation theory

Effect of boron additions on phase formation and magnetic properties of TbCu7-type melt spun SmFe ribbons

International Nuclear Information System (INIS)

Zheng, Chuanjiang; Yu, Dunbo; Li, Kuoshe; Luo, Yang; Jin, Jinling; Lu, Shuo; Li, Hongwei; Mao, Yongjun; Quan, Ningtao

2016-01-01

Melt spun ribbons of a series of SmFe 12 B x (x=0.0, 0.5, 0.75, 1.0, 1.25, and 1.5) have been prepared by the melt spinning technique. Sm–Fe–B melt spun ribbons with single phase TbCu 7 -type structure were prepared from the SmFe 12 B x (x=0.5, 0.75, and 1.0) alloys at the surface velocity around 40 m/s. The addition of boron not only inhibits the appearance of soft magnetic phase α-Fe, but also enhances the ability of amorphous formation for melt spun Sm–Fe ribbons. The concentration of boron atoms, however, exceeds the limit of the solubility (x>1.0) of Sm–Fe alloys, which does not impede the appearance of α-Fe but accelerates the formation of metastable phase Sm 2 Fe 23 B 3 that is unfavorable to their magnetic properties. Moreover, it is found that the addition of boron whose concentration is 0.0≤x≤0.75 can stabilize the metastable TbCu 7 -type structure because of the increase of the lattice parameter ratio c/a. The magnetic properties of as-annealed SmFe 12 B 1.0 melt spun ribbons with an energy product of 2.19MGOe, a coercivity of 2.36 kOe and a remanence of 4.8 kGs have been achieved. The microstructural characteristics of as-annealed melt spun SmFe 12 and SmFe 12 B 1.0 ribbons have been discussed as well. The following sequence of the hyperfine field H(6l)Fe Mossbauer spectra. As the boron content is added gradually, the hyperfine fields of 3g and 6l sites increase slightly due to the competition of the positive electron polarization and the negative polarization. However, the value of H(2e) is almost constant. - Highlights: • A certain amount of boron additions can inhibit the emergence of the soft magnetic phase α-Fe and improve the ability of amorphous formation. • There is a solubility limit of boron atom within melt spun Sm–Fe alloys with TbCu 7 -type structure, and the metastable phase Sm 2 Fe 23 B 3 will appear when the content of boron

Basin scale survey of marine humic fluorescence in the Atlantic: relationship to iron solubility and H2O2

OpenAIRE

Heller, Maija; Gaiero, Diego; Croot, Peter

2013-01-01

Iron (Fe) is a limiting nutrient for phytoplankton productivity in many different oceanic regions. A critical aspect underlying iron limitation is its low solubility in seawater as this controls the distribution and transport of iron through the ocean. Processes which enhance the solubility of iron in seawater, either through redox reactions or organic complexation, are central to understanding the biogeochemical cycling of iron. In this work we combined iron solubility measurements with para...

Time evolution of morphology in mechanically alloyed Fe-Cu

KAUST Repository

Wille, Catharina Gabriele; Al-Kassab, Talaá t; Kirchheim, Reiner

2011-01-01

Being widely accessible as well as already utilised in many applications, Fe-Cu acts as an ideal binary model alloy to elaborate the enforced nonequilibrium enhanced solubility in such a solution system that shows a limited regime of miscibility

Adsorption of As(V) from water using Mg-Fe-based hydrotalcite (FeHT)

Energy Technology Data Exchange (ETDEWEB)

Tuerk, T. [Mineral Processing Division, Department of Mining Engineering, Karadeniz Technical University, 61080 Trabzon (Turkey); Alp, I., E-mail: ialp@ktu.edu.tr [Mineral Processing Division, Department of Mining Engineering, Karadeniz Technical University, 61080 Trabzon (Turkey); Deveci, H. [Mineral Processing Division, Department of Mining Engineering, Karadeniz Technical University, 61080 Trabzon (Turkey)

2009-11-15

This paper describes a study of the sorptive removal of arsenate (As(V)) from aqueous solutions by synthetically prepared Mg-Fe-based hydrotalcites (FeHT) as layered double hydroxide (LDH) adsorbents. The synthesis of Fe{sup 3+}-substituted hydrotalcites (FeHT) with the chemical formula [Mg(II){sub 6}Fe(III){sub 2}(OH){sub 16}]{sup 2+}[CO{sub 3} x yH{sub 2}O]{sup 2-} was achieved by a co-precipitation method. The reaction products were characterized by powder X-ray diffraction analysis. The influences of solution pH, initial arsenate (As(V)) concentration, and sorbent concentration were investigated in multiple kinetic runs. The adsorption rates and isotherms were investigated in batch experiments. The pseudo-first-order and second-order kinetic models were tested and the latter was found to fit better to the experimental data. Langmuir and Freundlich isotherms were used to describe the adsorption data from equilibrium experiments. The results have shown that FeHT has a high arsenate removal efficiency, with the ability to reduce the concentration of arsenate in the aqueous solution from an initial value of 330 {mu}g/l to <10 {mu}g/l (i.e. below the limit value specified by WHO).

Iron solubility related to particle sulfur content in source emission and ambient fine particles.

Science.gov (United States)

Oakes, M; Ingall, E D; Lai, B; Shafer, M M; Hays, M D; Liu, Z G; Russell, A G; Weber, R J

2012-06-19

The chemical factors influencing iron solubility (soluble iron/total iron) were investigated in source emission (e.g., biomass burning, coal fly ash, mineral dust, and mobile exhaust) and ambient (Atlanta, GA) fine particles (PM2.5). Chemical properties (speciation and mixing state) of iron-containing particles were characterized using X-ray absorption near edge structure (XANES) spectroscopy and micro-X-ray fluorescence measurements. Bulk iron solubility (soluble iron/total iron) of the samples was quantified by leaching experiments. Major differences were observed in iron solubility in source emission samples, ranging from low solubility (iron solubility did not correspond to silicon content or Fe(II) content. However, source emission and ambient samples with high iron solubility corresponded to the sulfur content observed in single particles. A similar correspondence between bulk iron solubility and bulk sulfate content in a series of Atlanta PM2.5 fine particle samples (N = 358) further supported this trend. In addition, results of linear combination fitting experiments show the presence of iron sulfates in several high iron solubility source emission and ambient PM2.5 samples. These results suggest that the sulfate content (related to the presence of iron sulfates and/or acid-processing mechanisms by H(2)SO(4)) of iron-containing particles is an important proxy for iron solubility.

Accumulating the hydride state in the catalytic cycle of [FeFe]-hydrogenases

Science.gov (United States)

Winkler, Martin; Senger, Moritz; Duan, Jifu; Esselborn, Julian; Wittkamp, Florian; Hofmann, Eckhard; Apfel, Ulf-Peter; Stripp, Sven Timo; Happe, Thomas

2017-07-01

H2 turnover at the [FeFe]-hydrogenase cofactor (H-cluster) is assumed to follow a reversible heterolytic mechanism, first yielding a proton and a hydrido-species which again is double-oxidized to release another proton. Three of the four presumed catalytic intermediates (Hox, Hred/Hred and Hsred) were characterized, using various spectroscopic techniques. However, in catalytically active enzyme, the state containing the hydrido-species, which is eponymous for the proposed heterolytic mechanism, has yet only been speculated about. We use different strategies to trap and spectroscopically characterize this transient hydride state (Hhyd) for three wild-type [FeFe]-hydrogenases. Applying a novel set-up for real-time attenuated total-reflection Fourier-transform infrared spectroscopy, we monitor compositional changes in the state-specific infrared signatures of [FeFe]-hydrogenases, varying buffer pH and gas composition. We selectively enrich the equilibrium concentration of Hhyd, applying Le Chatelier's principle by simultaneously increasing substrate and product concentrations (H2/H+). Site-directed manipulation, targeting either the proton-transfer pathway or the adt ligand, significantly enhances Hhyd accumulation independent of pH.

Correlations of particle number concentrations and metals with nitrogen oxides and other traffic-related air pollutants in Glasgow and London

Science.gov (United States)

Sánchez Jiménez, Araceli; Heal, Mathew R.; Beverland, Iain J.

2012-07-01

Particle number concentration (PNC) and transition metal content are implicated in the health effects of airborne particulate matter (PM) but they are difficult to measure so consequently their temporal and spatial variations are not well characterized. Daily concentrations of PNC and particle-bound water-soluble metals (V, Cr, Mn, Fe, Ni, Cu, As, Cd and Pb) were measured at background and kerbside sites in Glasgow and London to examine if other metrics of air pollution such as optical darkness (absorbance) of collected filter samples of PM, gravimetric PM, and NO, NO2 and CO gas concentrations, can be used as surrogates for the temporal and spatial variations of the former. NO2 and NOx exhibited a high degree of within-site correlation and with PNC and water-soluble metals (Fe, Cu, As, Cd, Pb) at background sites in both cities. There is therefore potential to use NO2 and NOx as surrogates for PNC and water-soluble metal at background sites. However, correlation was weaker in complex street canyon environments where pollutant concentrations are strongly affected by local sources and the small-scale variations in pollutant dispersion induced by the wind regimes within street canyons. The corollary of the high correlation between NO2 and PNC and water-soluble metals at the background sites is that the latter pollutants may act as confounders for health effects attributed to NO2 from such sites. Concentrations of CO cannot be used as a surrogate for PNC. Increments in daily NOx and NO2 concentrations between trafficked and background sites were shown to be a simple and novel surrogate for daily spatial variation of PNC; for example, increments in NOx explained 78-79% of the variance in PNC at the paired sites in both Glasgow and London, but relationships were city specific. The increments in NOx also explained 70% of the spatial variation in Cu and Ni in Glasgow but not in London. Weekly NO2 measurements derived from passive diffusion tubes were also shown to

Microbial removal of Fe(III) impurities from clay using dissimilatory iron reducers.

Science.gov (United States)

Lee, E Y; Cho, K S; Ryu, H W; Chang, Y K

1999-01-01

Fe(III) impurities, which detract refractoriness and whiteness from porcelain and pottery, could be biologically removed from low-quality clay by indigenous dissimilatory Fe(III)-reducing microorganisms. Insoluble Fe(III) in clay particles was leached out as soluble Fe(II), and the Fe(III) reduction reaction was coupled to the oxidation of sugars such as glucose, maltose and sucrose. A maximum removal of 44-45% was obtained when the relative amount of sugar was 5% (w/w; sugar/clay). By the microbial treatment, the whiteness of the clay was increased from 63.20 to 79.64, whereas the redness was clearly decreased from 13.47 to 3.55.

The influence of Fe(II) competition on the sorption and migration of Ni(II) in MX-80 bentonite

International Nuclear Information System (INIS)

Pfingsten, Wilfried; Bradbury, Mike; Baeyens, Bart

2011-01-01

two competing sorbates and their respective concentrations. At background Fe(II) concentrations of 5.3 x 10 -5 M, and a Ni(II) EQBM level of 10 -7 M, the Ni(II) breakthrough time was ∼15 times earlier than in the absence of competition. At such Fe(II) concentrations the Ni(II) breakthrough curves at all source concentrations less than 3.5 x 10 -5 M (fixed by the NiCO 3,S solubility limit) are the same i.e. Ni(II) exhibits linear (low) sorption. Competitive sorption effects can have significant influences on the transport of radionuclides through compacted bentonite i.e. reduce the migration rates. Since, for the case considered here, the Fe(II) concentration in the near field of a high-level radioactive waste repository may change in time and space, the transport of bivalent transition metal radionuclides can only be properly modelled using a multi-species reactive transport code which includes a sorption model.

The impact of particle size, relative humidity, and sulfur dioxide on iron solubility in simulated atmospheric marine aerosols.

Science.gov (United States)

Cartledge, Benton T; Marcotte, Aurelie R; Herckes, Pierre; Anbar, Ariel D; Majestic, Brian J

2015-06-16

Iron is a limiting nutrient in about half of the world's oceans, and its most significant source is atmospheric deposition. To understand the pathways of iron solubilization during atmospheric transport, we exposed size segregated simulated marine aerosols to 5 ppm sulfur dioxide at arid (23 ± 1% relative humidity, RH) and marine (98 ± 1% RH) conditions. Relative iron solubility increased as the particle size decreased for goethite and hematite, while for magnetite, the relative solubility was similar for all of the fine size fractions (2.5-0.25 μm) investigated but higher than the coarse size fraction (10-2.5 μm). Goethite and hematite showed increased solubility at arid RH, but no difference (p > 0.05) was observed between the two humidity levels for magnetite. There was no correlation between iron solubility and exposure to SO2 in any mineral for any size fraction. X-ray absorption near edge structure (XANES) measurements showed no change in iron speciation [Fe(II) and Fe(III)] in any minerals following SO2 exposure. SEM-EDS measurements of SO2-exposed goethite revealed small amounts of sulfur uptake on the samples; however, the incorporated sulfur did not affect iron solubility. Our results show that although sulfur is incorporated into particles via gas-phase processes, changes in iron solubility also depend on other species in the aerosol.

Thermodynamics of the Mo-Fe-C and W-Fe-C systems

International Nuclear Information System (INIS)

Kleykamp, H.

1978-01-01

A study on the reaction behaviour of the components of the Mo 2 C-Fe and WC-Fe systems is presented. Both systems are stable if the mono-phase carbides are in equilibrium with the Fe-C solid solution within fixed carbon concentrations, the limits of which are calculated in this paper. Gibbs energies of formation at 1273 K of the intermetallic phases, of the binary and of the ternary carbides in the Mo-Fe-C and W-Fe-C systems were determined. The Fe corner in the phase diagrams of both systems and the calculated C boundaries in the two-phase field γ-Fe(Mo,C)-Mo 2 C and the γ-Fe(W,C)-WC, respectively, based on this study, are shown in figures. (GSC) [de

Oxidative Pressure Leaching of Silver from Flotation Concentrates with Ammonium Thiocyanate Solution

Science.gov (United States)

Yang, Sheng-Hai; Yang, Jian-Guang; Liu, Wei; Chen, Geng-Tao; Tang, Mo-Tang; Qiu, Guan-Zhou

2010-02-01

The thermodynamics and technologies of the selective pressure leaching of silver from flotation concentrates were investigated in an ammonium thiocyanate medium. Thermodynamic analyses, which include silver solubility in NH4SCN solution and Eh-pH diagrams of the Me-MeS-NH4SCN-H2O system at 25 °C, were discussed. The effects of several factors, such as temperature, leaching time, oxidant, pH value, flotation concentrates concentration, surfactant concentration, and so on, on the extraction percentages of silver and zinc were investigated. The following optimal leaching conditions were obtained: NH4SCN concentration 1.5 M, lignin concentration 0.5 g/L, Fe3+ concentration 2 g/L, flotation concentrates addition 200 g/L, and oxygen pressure 1.2 MPa at 130 °C for 3 hours. Under these optimum conditions, the average extraction percentage of silver exceeded 94 pct, whereas the average extraction percentage of zinc was less than 3 pct. Only 7 pct of ammonium thiocyanate was consumed after 4 cycles, which indicated that ammonium thiocyanate hardly was oxidized under these oxidative pressure leaching conditions.

Study of Fe, Zn, Cu, Cd, Pb concentrations in liver, kidney and muscle tissue of cow and sheep marketed in Hamedan in 2011

Directory of Open Access Journals (Sweden)

S Sobhanardakani

2012-11-01

Full Text Available Importance of heavy metals in food safety and detrimental effects of their high concentrations in food stuff is well documented. In this study, concentrations of Fe, Zn, Cu, Cd and Pb in kidney, liver and muscle tissues of cow and sheep at Hamedan retails were evaluated. A total number of 180 samples was assessed for the amount of heavy metals as ppb in wet weight. For this, wet-digestion method was used to determine the concentration of given elements by ICP (Varian ES-710. Results showed that the highest concentration of heavy metals was determined in the liver and kidney samples, while the lowest concentration was found in muscle tissue. Among the heavy metals, Fe in cow’s liver had the highest concentration (25507±879 ppb and Cd in muscle tissue of sheep has the lowest concentration (192±54 ppb. In overall, accumulation of heavy metals in tissues of cows was higher than sheep. Statistical comparison of accumulated metals concentration in various tissues of these two animal groups showed significant difference (P

Synthesis and magnetic properties of prussian blue modified Fe nanoparticles

International Nuclear Information System (INIS)

Arun, T.; Prakash, K.; Justin Joseyphus, R.

2013-01-01

Fe nanoparticles are prepared using a unique polyol process and modified with prussian blue (PB) at various concentrations. The presence of PB in the Fe nanoparticles are confirmed from thermal, Fourier transform infrared spectroscopy and electron microscopic analyses. The prussian blue existed on ;the surface of the nanoparticles when the concentration is 200 μM and in excess with 1000 μM. ;Fe nanoparticles are reduced in size using Pt as nucleating agent and modified with the optimum concentration of PB. The saturation magnetization decreases with the concentration of PB whereas the coercivity is influenced by the size of the Fe nanoparticles. The presence of oxide layer in Fe nanoparticles helps in the surface modification with PB. The Fe nanoparticles of particle size 53 nm modified with 200 μM of PB showed a saturation magnetization of 110 emu/g. The magnetic properties suggest that the PB modified Fe nanoparticles are better candidates for detoxification applications. - Highlights: • Fe nanoparticles surface modified with prussian blue (PB) were synthesized. • Optimum PB concentration on size reduced Fe showed better magnetic properties. • Coercivity decreased with increasing concentration of PB. • Fe-PB nanoparticles could be used for detoxification applications

pH-metric solubility. 3. Dissolution titration template method for solubility determination.

Science.gov (United States)

Avdeef, A; Berger, C M

2001-12-01

The main objective of this study was to develop an effective potentiometric saturation titration protocol for determining the aqueous intrinsic solubility and the solubility-pH profile of ionizable molecules, with the specific aim of overcoming incomplete dissolution conditions, while attempting to shorten the data collection time. A modern theory of dissolution kinetics (an extension of the Noyes-Whitney approach) was applied to acid-base titration experiments. A thermodynamic method was developed, based on a three-component model, to calculate interfacial, diffusion-layer, and bulk-water reactant concentrations in saturated solutions of ionizable compounds perturbed by additions of acid/base titrant, leading to partial dissolution of the solid material. Ten commercial drugs (cimetidine, diltiazem hydrochloride, enalapril maleate, metoprolol tartrate, nadolol, propoxyphene hydrochloride, quinine hydrochloride, terfenadine, trovafloxacin mesylate, and benzoic acid) were chosen to illustrate the new titration methodology. It was shown that the new method is about 10 times faster in determining equilibrium solubility constants, compared to the traditional saturation shake-flask methods.

High Concentration of Serum Soluble Fas in Patients with Head and Neck Carcinoma: A Comparative Study Before and After Surgical Removal of Tumor

OpenAIRE

Seyed Basir Hashemi; Mohammad Javad Fattahi; Mansooreh Jaberipour; Mojtaba Habibagahi; Mahmood Shariati

2010-01-01

Background:Alternative splicing of the Fas transcript can produce a naturalsecreted isoform of this molecule. Some cancer cells can also produce soluble Fas (sFas)which may have suppressive effects on the immune system's anti-tumor response.Elevated concentrations of sFas have been detected in the sera of patients with differentmalignancies. Materials and Methods:The concentrations of sFas in sera of patients with headand neck carcinoma (HNC, n=98) and healthy individuals (n=30) were measured...

Effect of boron additions on phase formation and magnetic properties of TbCu{sub 7}-type melt spun SmFe ribbons

Energy Technology Data Exchange (ETDEWEB)

Zheng, Chuanjiang; Yu, Dunbo, E-mail: yudb2008@126.com; Li, Kuoshe; Luo, Yang; Jin, Jinling; Lu, Shuo; Li, Hongwei; Mao, Yongjun; Quan, Ningtao

2016-08-15

Melt spun ribbons of a series of SmFe{sub 12}B{sub x} (x=0.0, 0.5, 0.75, 1.0, 1.25, and 1.5) have been prepared by the melt spinning technique. Sm–Fe–B melt spun ribbons with single phase TbCu{sub 7}-type structure were prepared from the SmFe{sub 12}B{sub x} (x=0.5, 0.75, and 1.0) alloys at the surface velocity around 40 m/s. The addition of boron not only inhibits the appearance of soft magnetic phase α-Fe, but also enhances the ability of amorphous formation for melt spun Sm–Fe ribbons. The concentration of boron atoms, however, exceeds the limit of the solubility (x>1.0) of Sm–Fe alloys, which does not impede the appearance of α-Fe but accelerates the formation of metastable phase Sm{sub 2}Fe{sub 23}B{sub 3} that is unfavorable to their magnetic properties. Moreover, it is found that the addition of boron whose concentration is 0.0≤x≤0.75 can stabilize the metastable TbCu{sub 7}-type structure because of the increase of the lattice parameter ratio c/a. The magnetic properties of as-annealed SmFe{sub 12}B{sub 1.0} melt spun ribbons with an energy product of 2.19MGOe, a coercivity of 2.36 kOe and a remanence of 4.8 kGs have been achieved. The microstructural characteristics of as-annealed melt spun SmFe{sub 12} and SmFe{sub 12}B{sub 1.0} ribbons have been discussed as well. The following sequence of the hyperfine field H(6l)Fe Mossbauer spectra. As the boron content is added gradually, the hyperfine fields of 3g and 6l sites increase slightly due to the competition of the positive electron polarization and the negative polarization. However, the value of H(2e) is almost constant. - Highlights: • A certain amount of boron additions can inhibit the emergence of the soft magnetic phase α-Fe and improve the ability of amorphous formation. • There is a solubility limit of boron atom within melt spun Sm–Fe alloys with TbCu{sub 7}-type structure, and the

The measurement of metallic uranium solubility in lithium chloride molten salt

International Nuclear Information System (INIS)

Park, K. K.; Choi, I. K.; Yeon, J. W.; Choi, K. S.; Park, Y. J.

2002-01-01

For the purpose of more precise solubility measurement of metallic uranium in lithium chloride melt, the effect of lithium chloride on uranium determination and and the change of oxidation state of metallic uranium in the media were investigated. Uranium of higher than 10 μg/g could be directly determined by ICP-AES. In the case of the lower concentration, the separation and concentration of uranium by anion exchanger was followed by ICP-AES, thereby extending the measurable concentration to 0.1 μg/g. The effects of lithium oxide, uranium oxides(UO 2 or U 3 O 8 ) and metallic lithium on the solubility of metallic uranium were individually investigated in glassy carbon or stainless steel crucibles under argon gas atmosphere. Since metallic uranium is oxidized to uranium(III) in the absence of metallic lithium, causing an increase in the solubility, metallic lithium as reducing agent should be present in the reaction media to obtain the more precise solubility. The metallic uranium solubilities measured at 660 and 690 .deg. C were both lower than 10 μg/g

Oxidation of Fe(II) in rainwater.

Science.gov (United States)

Willey, J D; Whitehead, R F; Kieber, R J; Hardison, D R

2005-04-15

Photochemically produced Fe(II) is oxidized within hours under environmentally realistic conditions in rainwater. The diurnal variation between photochemical production and reoxidation of Fe(II) observed in our laboratory accurately mimics the behavior of ferrous iron observed in field studies where the highest concentrations of dissolved Fe(ll) occur in afternoon rain during the period of maximum sunlight intensity followed by gradually decreasing concentrations eventually returning to early morning pre-light values. The experimental work presented here, along with the results of kinetics studies done by others, suggests thatthe primary process responsible for the decline in photochemically produced Fe(II) concentrations is oxidation by hydrogen peroxide. This reaction is first order with respect to both the concentrations of Fe(II) and H2O2. The second-order rate constant determined for six different authentic rain samples varied over an order of magnitude and was always less than or equal to the rate constant determined for this reaction in simple acidic solutions. Oxidation of photochemically produced ferrous iron by other oxidants including molecular oxygen, ozone, hydroxyl radical, hydroperoxyl/superoxide radical, and hexavalent chromium were found to be insignificant under the conditions present in rainwater. This study shows that Fe(II) occurs as at least two different chemical species in rain; photochemically produced Fe(II) that is oxidized over time periods of hours, and a background Fe(II) that is protected against oxidation, perhaps by organic complexation, and is stable against oxidation for days. Because the rate of oxidation of photochemically produced Fe(II) does not increase with increasing rainwater pH, the speciation of this more labile form of Fe(II) is also not controlled by simple hydrolysis reactions.

Intermetallic phases in the iron-rich region of the Zr-Fe phase diagram

International Nuclear Information System (INIS)

Granovsky, M.S.; Arias, D.

1996-01-01

Intermetallic phases in the Fe-rich region of the Zr-Fe system are studied by X-ray diffraction and optical and electron microscopy. The chemical composition of each phase has been quantitatively measured in a electron microprobe. The stable phases found in this region are ZrFe 2 , Zr 6 Fe 23 and (αFe). ZrFe 2 is identified as a cubic Laves type phase (C15) and the ZrFe 2 /ZrFe 2 +Zr 6 Fe 23 boundary composition is 73±1 at.% Fe. Zr 6 Fe 23 is a cubic phase of the Th 6 Mn 23 type and its composition is 80.0±1.5 at.% Fe. The eutectic L↔Zr 6 Fe 23 +τ-Fe transformation temperature and composition are 1325 C and 91±1 at.% Fe, respectively. The solubility of Zr in τ-Fe at 1012 C is 500±50 appm and 1000±100 appm close to the eutectic temperature. (orig.)

Actinide solution equlibria and solubilities in geologic systems

International Nuclear Information System (INIS)

Allard, B.

1983-04-01

Stability constants and solubility products for actinide (Th, U, Np, Pu and Am) hydroxide and carbonate complexes have been collected, and total solubilities have been calculated under conditions representative of deep granitic groundwaters (pH 7-9.5; high total carbonate concentration according to log (CO 3 )=0.76pH-10.83; redox potentials corresponding to oxic systems, Eh>0.8-0.06pH, and reducing systems, Eh 2 (s), UO 2 (s), NpO 2 (s), PuO 2 (s) and Am 2 (CO 3 ) 3 (s)m, respectively, and the corresponding calculated maximum solubilities are 3 times 10- 10 M(0.07 μg/1) for Th, 0.3-250 times 10- 10 M (0.01-6 μg/1) for U (depending on the carbonate concentration), 1 times 10- 10 M(0.03 μg/1) for Np, 1-3 times 10- 9 M (0.2-0.7 μg/1) for Pu and 0.6-2 times 10- 7 M (15-50 μg/1) for Am. The calculated solubilities for U are in fair agreement with observed uranium concentrations in natural deep groundwaters. Hexavalent uranium carbonate species would dominate in solution except under highly reducing conditions (Eh 5 -10- 6 M (mg/1-level). (author)

Evaluation of surface energy state distribution and bulk defect concentration in DSSC photoanodes based on Sn, Fe, and Cu doped TiO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Ako, Rajour Tanyi [Faculty of Science, Universiti Brunei Darussalam, Jalan Tungku Link, BE1410, Negara (Brunei Darussalam); Ekanayake, Piyaisiri, E-mail: piyasiri.ekanayake@ubd.edu.bn [Faculty of Science, Universiti Brunei Darussalam, Jalan Tungku Link, BE1410, Negara (Brunei Darussalam); Young, David James [Faculty of Science, Universiti Brunei Darussalam, Jalan Tungku Link, BE1410, Negara (Brunei Darussalam); Institute of Materials Research and Engineering (IMRE), Agency for Science, Technology and Research -A*STAR, 3 Research Link, 117602 (Singapore); Faculty of Science, Health, Education and Engineering, University of the Sunshine Coast, Locked Bag 4, Maroochydore DC, Queensland, 4558 (Australia); Hobley, Jonathan [Faculty of Science, Universiti Brunei Darussalam, Jalan Tungku Link, BE1410, Negara (Brunei Darussalam); Chellappan, Vijila [Institute of Materials Research and Engineering (IMRE), Agency for Science, Technology and Research - A*STAR, 3 Research Link, 117602 (Singapore); Tan, Ai Ling [Faculty of Science, Universiti Brunei Darussalam, Jalan Tungku Link, BE1410, Negara (Brunei Darussalam); Gorelik, Sergey; Subramanian, Gomathy Sandhya [Institute of Materials Research and Engineering (IMRE), Agency for Science, Technology and Research - A*STAR, 3 Research Link, 117602 (Singapore); Lim, Chee Ming [Faculty of Science, Universiti Brunei Darussalam, Jalan Tungku Link, BE1410, Negara (Brunei Darussalam)

2015-10-01

Graphical abstract: - Highlights: • The structural, optical and optoelectronic properties of 1 mol.% Fe, Sn and Cu doped TiO{sub 2} have been compared. • Transient lifetimes for pure TiO{sub 2} and Sn doped TiO{sub 2} were considerably shorter than Fe and Cu doped TiO{sub 2}. • A good correlation between the bulk defects and transient decay for the doped TiO{sub 2} powders was observed. • Photon to current conversion efficiency of DSSC based on the metal doped TiO{sub 2} were in order Sn-TiO{sub 2} > Cu-TiO{sub 2} > Pure >> Fe-TiO{sub 2}. • DSSC based on Fe doped photoanodes is limited by a high concentration of surface free holes observed at 433 nm. - Abstract: Electron transfer dynamics in the oxide layers of the working electrodes in both dye-sensitized solar cells and photocatalysts greatly influences their performance. A proper understanding of the distribution of surface and bulk energy states on/in these oxide layers can provide insights into the associated electron transfer processes. Metal ions like Iron (Fe), Copper (Cu) and Tin (Sn) doped onto TiO{sub 2} have shown enhanced photoactivity in these processes. In this work, the structural, optical and transient properties of Fe, Cu and Sn doped TiO{sub 2} nanocrystalline powders have been investigated and compared using EDX, Raman spectroscopy, X-ray Photoelectron spectroscopy (XPS), and Transient Absorption spectroscopy (TAS). Surface free energy states distributions were probed using Electrochemical Impedance spectroscopy (EIS) on Dye Sensitized Solar Cells (DSSC) based on the doped TiO{sub 2} photoanodes. Raman and XPS Ti2p{sub 3/2} peak shifts and broadening showed that the concentration of defects were in the order: Cu doped TiO{sub 2} > Fe doped TiO{sub 2} > Sn doped TiO{sub 2} > pure TiO{sub 2}. Nanosecond laser flash photolysis of Fe and Cu doped TiO{sub 2} indicated slower transient decay kinetics than that of Sn doped TiO{sub 2} or pure TiO{sub 2}. A broad absorption peak and fast

Study on the extraction characteristics of Fe(III) with trialkylphosphine oxide

International Nuclear Information System (INIS)

Zhang Qiwei; Jiao Rongzhou; Song Chongli

1994-08-01

The extractive properties of TRPO (trialkyephosphine oxide) as the extractant for the Fe(III) have been studied. Under this experiment condition, the distribution ratio D of Fe (III) with the changes of extraction equilibrium time, temperature, nitric acid concentration and Fe 3+ concentration in aqueous solution have been determined. The ΔH degree, ΔS degree and apparent equilibrium constant K of the reaction in which Fe (III) is extracted by TRPO have been calculated. The experiment results show that the third phase appearance in 30% TRPO extractive system has close relations with Fe 3+ concentration in aqueous solution. When nitric acid concentration is 1.5 mol/L and Fe 3+ initial concentration is higher than 8.0 g/L in aqueous solution, the extractant system appears third phase. Two organic phase volume ratio and Fe(III) concentration ratio in the organic phases have been determined respectively, and they vary with the Fe 3+ concentration in aqueous solution

Novel Schiff base (DBDDP) selective detection of Fe (III): Dispersed in aqueous solution and encapsulated in silica cross-linked micellar nanoparticles in living cell.

Science.gov (United States)

Gai, Fangyuan; Yin, Li; Fan, Mengmeng; Li, Ling; Grahn, Johnny; Ao, Yuhui; Yang, Xudong; Wu, Xuming; Liu, Yunling; Huo, Qisheng

2018-03-15

This work demonstrated the synthesis of (4E)-4-(4-(diphenylamino)benzylideneamino)-1,2-dihydro-1,5- dimethyl-2-phenylpyrazol-3-one (DBDDP) for Fe (III) detection in aqueous media and in the core of silica cross-linked micellar nanoparticles in living cells. The free DBDDP performed fluorescence enhancement due to Fe (III)-promoted hydrolysis in a mixed aqueous solution, while the DBDDP-doped silica cross-linked micellar nanoparticles (DBDDP-SCMNPs) performed an electron-transfer based fluorescence quenching of Fe (III) in living cells. The quenching fluorescence of DBDDP-SCMNPs and the concentration of Fe (III) exhibited a linear correlation, which was in accordance with the Stern-Volmer equation. Moreover, DBDDP-SCMNPs showed a low limit of detection (LOD) of 0.1 ppm and an excellent selectivity against other metal ions. Due to the good solubility and biocompatibility, DBDDP-SCMNPs could be applied as fluorescence quenching nanosensors in living cells. Copyright © 2017 Elsevier Inc. All rights reserved.

Physiological and morphological adaptations of herbaceous perennial legumes allow differential access to sources of varyingly soluble phosphate.

Science.gov (United States)

Pang, Jiayin; Yang, Jiyun; Lambers, Hans; Tibbett, Mark; Siddique, Kadambot H M; Ryan, Megan H

2015-08-01

The aim of this study was to investigate the capacity of three perennial legume species to access sources of varyingly soluble phosphorus (P) and their associated morphological and physiological adaptations. Two Australian native legumes with pasture potential (Cullen australasicum and Kennedia prostrata) and Medicago sativa cv. SARDI 10 were grown in sand under two P levels (6 and 40 µg P g(-1) ) supplied as Ca(H2 PO4 )2 ·H2 O (Ca-P, highly soluble, used in many fertilizers) or as one of three sparingly soluble forms: Ca10 (OH)2 (PO4 )6 (apatite-P, found in relatively young soils; major constituent of rock phosphate), C6 H6 O24 P6 Na12 (inositol-P, the most common form of organic P in soil) and FePO4 (Fe-P, a poorly-available inorganic source of P). All species grew well with soluble P. When 6 µg P g(-1) was supplied as sparingly soluble P, plant dry weight (DW) and P uptake were very low for C. australasicum and M. sativa (0.1-0.4 g DW) with the exception of M. sativa supplied with apatite-P (1.5 g). In contrast, K. prostrata grew well with inositol-P (1.0 g) and Fe-P (0.7 g), and even better with apatite-P (1.7 g), similar to that with Ca-P (1.9 g). Phosphorus uptake at 6 µg P g(-1) was highly correlated with total root length, total rhizosphere carboxylate content and total rhizosphere acid phosphatase (EC 3.1.3.2) activity. These findings provide strong indications that there are opportunities to utilize local Australian legumes in low P pasture systems to access sparingly soluble soil P and increase perennial legume productivity, diversity and sustainability. © 2014 Scandinavian Plant Physiology Society.

Effect of dispersed particles of calcium fluoride on the molybdenum solubility in iron

International Nuclear Information System (INIS)

Shvejkin, G.P.; Antsiferov, V.N.; Postnikov, V.S.

1981-01-01

The results of the investigation of compositions containing 20 at% Mo and 12 vol.% CaF 2 are presented. The sample diffractograms of compositions Fe+20 at% Mo and (Fe+20 at% Mo)+12 vol.% CaF 2 are given. It is shown that the introduction of calcium fluoride results in formation of continuos series of solid solutions of molybdenum in iron. The results of X-ray diffraction investigations on exceeding solubility limit of molybdenum in iron in the presence of calcium fluoride are confirmed

A solar rechargeable flow battery based on photoregeneration of two soluble redox couples.

Science.gov (United States)

Liu, Ping; Cao, Yu-liang; Li, Guo-Ran; Gao, Xue-Ping; Ai, Xin-Ping; Yang, Han-Xi

2013-05-01

Storable sunshine, reusable rays: A solar rechargeable redox flow battery is proposed based on the photoregeneration of I(3)(-)/I(-) and [Fe(C(10)H(15))(2)](+)/Fe(C(10)H(15))(2) soluble redox couples, which can be regenerated by flowing from a discharged redox flow battery (RFB) into a dye-sensitized solar cell (DSSC) and then stored in tanks for subsequent RFB applications This technology enables effective solar-to-chemical energy conversion. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Soluble CD30 concentrations in ESRD patients with and without panel reactive HLA antibodies.

Science.gov (United States)

Vaidya, Smita; Partlow, David; Barnes, Titus; Thomas, Phillip; Gugliuzza, Kristin

2006-01-01

In this retrospective study we compared accuracy of panel reactive antibodies (PRA) with serum soluble CD30 (sCD30) contents in predicting acute rejection crisis post-renal transplant. Pre-transplant sera from 115 patients were evaluated for their PRA and sCD30 concentrations. All patients received calcineurin inhibitor-based immunosuppressive therapy. Objective measurements for rejection were biopsy-proven acute rejection (AR) episodes within first six months of the transplant. Post-transplant sera of patients with AR were tested for the presence of donor-specific HLA antibodies (DSA). Overall AR rate was 16% (18/115). Patients positive for PRA and sCD30 tests were at significantly higher risk for AVR compared with those patients negative for both the tests (36% vs. 5%, p=0.01). Among negative PRA patients risk for AR was significantly elevated if they were also tested positive for sCD30 concentrations (21% vs. 5%, p=0.04). Of the 18 patients with AR, 14 were positive for sCD30, and 13 of them (93%) developed DSA post-transplant (p=0.001). These data showed that patients positive for sCD30 contents are at high risk for the development of DSA and AR post-transplant regardless of their pre-transplant PRA.

On nitrogen solubility in water

International Nuclear Information System (INIS)

Kalajda, Yu.A.; Katkov, Yu.D.; Kuznetsov, V.A.; Lastovtsev, A.Yu.; Lastochkin, A.P.; Susoev, V.S.

1980-01-01

Presented are the results of experimental investigations on nitrogen solubility in water under 0-15 MPa pressure, at the temperature of 100-340 deg C and nitrogen concentration of 0-5000 n.ml. N 2 /kg H 2 O. Empiric equations are derived and a diagram of nitrogen solubility in water is developed on the basis of the experimental data, as well as critically evaluated published data. The investigation results can be used in analyzing water-gas regime of a primary heat carrier in stream-generating plants with water-water reactors

Solubility of rare earth-iron borates in the Bi2O3-B2O3 melt and their crystallization

International Nuclear Information System (INIS)

Al'shinskaya, L.I.; Leonyuk, N.I.; Nadezhnaya, T.B.; Timchenko, T.I.

1979-01-01

The temperature dependence of solubility of RFe 3 (BO 3 ) 4 (R=Y, Gd, Nd, Er) double borates in the Bi 2 O 3 -B 2 O 3 solution-melt is studied. The solubility curves in the range from 25 to 52 mol% are plotted. The character of curves is almost similar. At equal temperatures YFe 3 (BO 3 ) 4 and ErFe 3 (BO 3 ) 4 have the highest solubility and GaFe 3 (BO 3 ) 4 - the lowest one. It is shown that in the Bi 2 O 3 -B 2 O 3 base solution-melt the wide temperature range of monophase crystallization of rare earth - iron borates exists and the stratification is not observed. Thus, for the first time obtained are the crystals of rare earth-iron borates suitable for the investigation of their physical properties

Effects of Au/Fe and Fe nanoparticles on Serratia bacterial growth and production of biosurfactant

International Nuclear Information System (INIS)

Liu, Jia; Vipulanandan, Cumaraswamy

2013-01-01

The overall objective of this study was to compare the effects of Au/Fe and Fe nanoparticles on the growth and performance of Serratia Jl0300. The nanoparticle effect was quantified not only by the bacterial growth on agar plate after 1 hour interaction with the nanoparticles, but also by its production of a biosurfactant from used vegetable oil. The nanoparticles were prepared using the foam method. The concentrations of the nanoparticles used for the bacterial interaction study were varied from 1 mg/L to 1 g/L. The test results showed that the effect of nanoparticles on the bacterial growth and biosurfactant production varied with nanoparticle type, concentrations, and interaction time with the bacteria. Au/Fe nanoparticles didn't show toxicity to Serratia after short time (1 h) exposure, while during 8 days fermentation Au/Fe nanoparticles inhibited the growth of Serratia as well as the biosurfactant production when the concentration of the nanoparticles was higher than 10 mg/L. Fe nanoparticles showed inhibition effects to bacterial growth both after short time and long time interaction with Serratia, as well as to biosurfactant production when its concentration was higher than 100 mg/L. Based on the trends observed in this study, analytical models have been developed to predict the bacterial growth and biosurfactant production with varying concentrations of nanoparticles. - Highlights: • Modeled the effect of nanoparticles on the bacterial growth and biosurfactant production. • Effects of Au/Fe nonoparticles on Serratia Bacterial Growth and Production of Biosurfactant. • Scanning Electron Micrograph of bacteria-nanoparticles interaction

Effects of Au/Fe and Fe nanoparticles on Serratia bacterial growth and production of biosurfactant

Energy Technology Data Exchange (ETDEWEB)

Liu, Jia; Vipulanandan, Cumaraswamy, E-mail: cvipulanandan@uh.edu

2013-10-15

The overall objective of this study was to compare the effects of Au/Fe and Fe nanoparticles on the growth and performance of Serratia Jl0300. The nanoparticle effect was quantified not only by the bacterial growth on agar plate after 1 hour interaction with the nanoparticles, but also by its production of a biosurfactant from used vegetable oil. The nanoparticles were prepared using the foam method. The concentrations of the nanoparticles used for the bacterial interaction study were varied from 1 mg/L to 1 g/L. The test results showed that the effect of nanoparticles on the bacterial growth and biosurfactant production varied with nanoparticle type, concentrations, and interaction time with the bacteria. Au/Fe nanoparticles didn't show toxicity to Serratia after short time (1 h) exposure, while during 8 days fermentation Au/Fe nanoparticles inhibited the growth of Serratia as well as the biosurfactant production when the concentration of the nanoparticles was higher than 10 mg/L. Fe nanoparticles showed inhibition effects to bacterial growth both after short time and long time interaction with Serratia, as well as to biosurfactant production when its concentration was higher than 100 mg/L. Based on the trends observed in this study, analytical models have been developed to predict the bacterial growth and biosurfactant production with varying concentrations of nanoparticles. - Highlights: • Modeled the effect of nanoparticles on the bacterial growth and biosurfactant production. • Effects of Au/Fe nonoparticles on Serratia Bacterial Growth and Production of Biosurfactant. • Scanning Electron Micrograph of bacteria-nanoparticles interaction.

COMPARISON OF DIFFERENT EXTRACTION METHODS REPRESENTING AVAILABLE AND TOTAL CONCENTRATIONS OF Cd, Cu, Fe, Mn and Zn IN SOIL

Directory of Open Access Journals (Sweden)

Vladimir Ivezić

2013-06-01

Full Text Available Various extraction methods are used to predict plant uptake of trace metals. Most commonly it is total concentration that is used for risk assessment and evaluation of trace metal availability. However, recent studies showed that total concentration is a poor indicator of availability while concentrations in soil solution show good correlation with plant uptake. Present study was conducted on magricultural soils with low levels of trace metals where 45 soil samples were collected from different soil types. The main objective was to compare four different extraction methods and examine how total and reactive (EDTA trace metal concentrations correlate ,with soil solution concentration (in this study determined by water extraction. The samples were analyzed by four extraction methods: strong acid extraction (ultra-pure HNO3 extraction and aqua regia, weak acid extraction by EDTA and the most available fraction, fraction in soil solution, were represented by water extraction (weakest extractant. Five elements were investigated (Cd, Cu, Fe, Mn and Zn. Water extraction significantly correlated with EDTA extraction for Cu, Fe and Mn, while total extraction (HNO3 extraction and aqua regia correlated significantly with water extraction only for Cu. No correlation between water extraction and total extraction confirmed poor role of total concentration as an indicator of availability. EDTA extraction can be used to represent reactive pool of trace metals in soil but it should be also taken with caution when using it to describe available fraction.

Solubility of hydrogen in metals and its effect of pore-formation and embrittlement. Ph.D. Thesis

Science.gov (United States)

Shahani, H. R.

1984-01-01

The effect of alloying elements on hydrogen solubility were determined by evaluating solubility equations and interaction coefficients. The solubility of dry hydrogen at one atmosphere was investigated in liquid aluminum, Al-Ti, Al-Si, Al-Fe, liquid gold, Au-Cu, and Au-Pd. The design of rapid heating and high pressure casting furnaces used in meta foam experiments is discussed as well as the mechanism of precipitation of pores in melts, and the effect of hydrogen on the shrinkage porosity of Al-Cu and Al-Si alloys. Hydrogen embrittlement in iron base alloys is also examined.

Ligand-assisted fabrication, structure, and luminescence properties of Fe:ZnSe quantum dots

International Nuclear Information System (INIS)

Xie, Ruishi; Zhang, Xingquan; Liu, Haifeng

2014-01-01

Highlights: • A green route is developed for synthesis of water-soluble and fluorescent Fe:ZnSe quantum dots. • Tunable luminescence intensity can be realized with different ligand-to-Zn molar ratios. • The obtained quantum dots are in the so-called “quantum confinement regime”. -- Abstract: Here, we report a synthetic route for highly emissive Fe:ZnSe quantum dots in aqueous media using the mercaptoacetic acid ligand as stabilizing agent. The structural, morphological, componential, and optical properties of the resulting quantum dots were explored by the X-ray diffraction, transmission electron microscopy, energy-dispersive X-ray spectroscopy, inductively coupled plasma mass spectrometry, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, photoluminescence and UV–visible absorption spectroscopies. The average crystallite size was calculated to be about ca., 4.0 nm using the Scherrer equation, which correlates well with the value obtained from the transmission electron microscopy analysis. The obtained water-soluble Fe:ZnSe quantum dots in the so-called “quantum confinement regime” are spherical shaped, possess the cubic sphalerite crystal structure, and exhibit tunable luminescence properties. The presence of mercaptoacetic acid on the surface of Fe:ZnSe quantum dots was confirmed by the Fourier transform infrared spectroscopy measurements. As the ligand/Zn molar ratio increases from 1.3 to 2.8, there is little shift in the absorption peak of the Fe:ZnSe sample, indicating that the particle size of the obtained quantum dots is not changed during the synthetic process. The photoluminescence quantum yield of the as-prepared water-soluble Fe:ZnSe quantum dots can be up to 39%. The molar ratio of ligand-to-Zn plays a crucial role in determining the final luminescence properties of the resulting quantum dots, and the maximum PL intensity appears as the ligand-to-Zn molar ratio is 2.2. In addition, the underlying mechanism for

Ligand-assisted fabrication, structure, and luminescence properties of Fe:ZnSe quantum dots

Energy Technology Data Exchange (ETDEWEB)

Xie, Ruishi, E-mail: rxie@foxmail.com; Zhang, Xingquan; Liu, Haifeng

2014-03-15

Highlights: • A green route is developed for synthesis of water-soluble and fluorescent Fe:ZnSe quantum dots. • Tunable luminescence intensity can be realized with different ligand-to-Zn molar ratios. • The obtained quantum dots are in the so-called “quantum confinement regime”. -- Abstract: Here, we report a synthetic route for highly emissive Fe:ZnSe quantum dots in aqueous media using the mercaptoacetic acid ligand as stabilizing agent. The structural, morphological, componential, and optical properties of the resulting quantum dots were explored by the X-ray diffraction, transmission electron microscopy, energy-dispersive X-ray spectroscopy, inductively coupled plasma mass spectrometry, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, photoluminescence and UV–visible absorption spectroscopies. The average crystallite size was calculated to be about ca., 4.0 nm using the Scherrer equation, which correlates well with the value obtained from the transmission electron microscopy analysis. The obtained water-soluble Fe:ZnSe quantum dots in the so-called “quantum confinement regime” are spherical shaped, possess the cubic sphalerite crystal structure, and exhibit tunable luminescence properties. The presence of mercaptoacetic acid on the surface of Fe:ZnSe quantum dots was confirmed by the Fourier transform infrared spectroscopy measurements. As the ligand/Zn molar ratio increases from 1.3 to 2.8, there is little shift in the absorption peak of the Fe:ZnSe sample, indicating that the particle size of the obtained quantum dots is not changed during the synthetic process. The photoluminescence quantum yield of the as-prepared water-soluble Fe:ZnSe quantum dots can be up to 39%. The molar ratio of ligand-to-Zn plays a crucial role in determining the final luminescence properties of the resulting quantum dots, and the maximum PL intensity appears as the ligand-to-Zn molar ratio is 2.2. In addition, the underlying mechanism for

Time evolution of morphology in mechanically alloyed Fe-Cu

KAUST Repository

Wille, Catharina Gabriele

2011-05-01

Being widely accessible as well as already utilised in many applications, Fe-Cu acts as an ideal binary model alloy to elaborate the enforced nonequilibrium enhanced solubility in such a solution system that shows a limited regime of miscibility and characterised by a large positive heat of mixing. In addition to the detailed analysis of ball milled Fe-Cu powders by means of Atom Probe Tomography (APT), site specific structural analysis has been performed in this study using Transmission Electron Microscopy (TEM).In this contribution results on powders with low Cu concentrations (2.5-10 at%) are presented. Combining a ductile element (Cu, fcc) and a brittle one (Fe, bcc), striking differences in morphology were expected and found on all length-scales, depending on the mixing ratio of the two elements. However, not only could the atomic mixing of Fe and Cu be evaluated, but also the distribution of impurities, mostly stemming from the fabrication procedure. The combination of APT and TEM enables a correlation between the structural evolution and the chemical mixing during the milling process. For the first time, a clear distinction can be drawn between the morphological evolution at the surface and in the interior of the powder particles. This became possible owing to the site specific sample preparation of TEM lamellae by Focussed Ion Beam (FIB). Surprisingly, the texture arising from the ball milling process can directly be related to the classical rolling texture of cold rolled Fe. In addition, full homogeneity can be achieved even on the nano-scale for this material as shown by APT, resulting in an extended miscibility region in comparison to the equilibrium phase diagram. Grain sizes were determined by means of XRD and TEM. The strain corrected XRD results are in very good agreement with the values derived by TEM, both confirming a truly nanocrystalline structure. © 2011 Elsevier B.V.

Simultaneous absorption of NO and SO{sub 2} into Fe-II-EDTA solution coupled with the Fe-II-EDTA regeneration catalyzed by activated carbon

Energy Technology Data Exchange (ETDEWEB)

Zhu, H.S.; Mao, Y.P.; Yang, X.J.; Chen, Y.; Long, X.L.; Yuan, W.K. [East China University of Science & Technology, Shanghai (China)

2010-07-30

The simultaneous removal of NO and SO{sub 2} from flue gases can be realized with Fe(II)-ethylenediamineteraacetate (EDTA) solution. Activated carbon is used to catalyze the reduction of Fe-III-EDTA to Fe-II-EDTA to maintain the capability of removing NO of the Fe-EDTA solution. The reductant is the sulfite/bisulfite ions produced by SO{sub 2} dissolving into the aqueous solution. Experiments have been performed to determine the effects of activated carbon of coconut shell, Fe-II-EDTA concentration, Fe/EDTA molar ratio, SO{sub 2} partial pressure, NO partial pressure and SO{sub 4}{sup 2-} concentration on the combined elimination of NO and SO{sub 2} with Fe-II-EDTA solution coupled with the Fe-II-EDTA regeneration catalyzed by activated carbon. According to the experimental results, activated carbon not only catalyzes the reduction of Fe-III-EDTA by sulfite/bisulfite greatly but also avoids the release of N{sub 2}O. The NO removal efficiency increases with the initial Fe-II-EDTA concentration and SO{sub 2} partial pressure. The ratio of Fe/EDTA and the SO{sub 4}{sup 2-} concentration has little effect on the catalytic reduction of Fe-III-EDTA. The optimal initial NO concentration range is from 600 ppm to 900 ppm. The experimental results manifest that the Fe-II-EDTA solution coupled with catalytic regeneration of Fe-II-EDTA can maintain high nitric oxide removal efficiency for a long period of time.

Iron-coupled inactivation of phosphorus in sediments by macrozoobenthos (chironomid larvae) bioturbation: Evidences from high-resolution dynamic measurements

International Nuclear Information System (INIS)

Chen, Musong; Ding, Shiming; Liu, Ling; Xu, Di; Han, Chao; Zhang, Chaosheng

2015-01-01

The effects of chironomid larvae bioturbation on the lability of phosphorus (P) in sediments were investigated through sediment incubation for 140 days. High-resolution dialysis (HR-Peeper) and diffusive gradients in thin films (DGT) techniques were applied to obtain soluble and labile P/Fe profiles at a millimeter resolution, respectively. The larvae bioturbation decreased concentrations of soluble/labile P and Fe by up to over half of the control at the sediment depths of influence up to 70 and 90 mm respectively. These effects continued over 116 days and disappeared on the 140th days due to eclosion of chironomid larvae. Labile P was highly correlated with labile Fe, while a weak correlation was observed between soluble P and soluble Fe. It was concluded that Fe(II) oxidation and its enhanced adsorption were the major mechanisms responsible for the decreases of soluble and labile P. - Highlights: • High resolution techniques were employed to study bioturbation effects on P. • Larvae bioturbation decreased the concentrations of soluble/labile P and Fe. • Bioturbation effects continued over 116 days and disappeared on the 140th days. • Labile P was more sensitive than pore water SRP in response to bioturbation. • It proved the mechanism of Fe-coupled inactivation of P in bioturbation sediments. - Chironomid larvae bioturation decreased the lability of P in sediments from Fe(II) oxidation and enhanced adsorption of P

Immobilization of Trichoderma harzianum α-amylase on PPyAgNp/Fe3O4-nanocomposite: chemical and physical properties.

Science.gov (United States)

Mohamed, Saleh A; Al-Harbi, Majed H; Almulaiky, Yaaser Q; Ibrahim, Ibrahim H; Salah, Hala A; El-Badry, Mohamed O; Abdel-Aty, Azza M; Fahmy, Afaf S; El-Shishtawy, Reda M

2018-03-26

In this study, a new support has been developed by immobilization of α-amylase onto modified magnetic Fe 3 O 4 -nanoparticles. The characterization of soluble and immobilized α-amylases with regards to kinetic parameters, pH, thermal stability and reusability was studied. The effect of polypyrrole/silver nanocomposite (PPyAgNp) percentage on weight of Fe 3 O 4 and pH on the immobilization of α-amylase was studied. The highest immobilization efficiency (75%) was detected at 10% PPyAgNp/Fe 3 O 4 -nanocomposite and pH 7.0. Immobilization of α-amylase on PPyAgNp/Fe 3 O 4 -nanocomposite was characterized by FT-IR spectroscopy and scanning electron microscopy. The reusability of the immobilized enzyme activity was 80% of its initial activity after 10 reuses. The immobilized enzyme was more stable towards pH, temperature and metal ions compared with soluble enzyme. The kinetic study appeared higher affinity of immobilized enzyme (K m 2.5 mg starch) compared with soluble enzyme (K m 3.5 mg starch). In conclusion, the immobilization of α-amylase on PPyAgNp/Fe 3 O 4 -nanocomposite could successfully be used in industrial and medical applications.

Mechanical alloying of the FeNi-Ag system

International Nuclear Information System (INIS)

Gonzalez, G.; Ibarra, D.; Ochoa, J.; Villalba, R.; Sagarzazu, A.

2007-01-01

The Fe-Ni-Ag system is of particular interest for its potential applications as soft magnetic granular material with small magnetic grains embedded in a non-magnetic metal matrix. Under equilibrium conditions: Fe-Ag and Ni-Ag are immiscible and Fe-Ni shows complete solubility. These materials are particularly important for magnetoresistivity properties. The properties of these alloys are closely related to their microstructure; therefore, a detailed study of the transformations occurring during milling was undertaken using pre-alloyed Fe x Ni 100-x (x = 30, 50 and 70) further milled with different Ag content to give the following alloys compositions (Fe x -Ni 100-x ) 100-y Ag y (y = 5, 20, 60). Consolidation of the mechanically alloyed powders by sintering at 950 o C was performed. Morphological and structural characterization of the sintered powders was carried out by scanning and transmission electron microscopy and X-ray diffraction. Fe 30 Ni 70 and Fe 50 Ni 50 formed ordered FeNi 3 compound. Fe 70 Ni 30 showed the formation of a mixture of γ-(Fe,Ni) and α-Fe(Ni) solid solutions. The mixture of these systems with Ag showed the metal solid solutions surrounded by Ag islands of Fe x Ni y -Ag, There was also evidence of Ag diffusing into the γ-(Fe,Ni). High Ag content (60%) shows formation of islands of FeNi surrounded by Ag. Sintering is always improved with the Ag content

Tetraphenylborate Solubility in High Ionic Strength Salt Solutions

International Nuclear Information System (INIS)

Serkiz, S.M.; Ginn, J.D.; Jurgensen, A.R.

1998-04-01

Solubility of sodium and potassium salts of the tetraphenylborate ion (TPB) in simulated Savannah River Site High Level Waste was investigated. Data generated from this study allow more accurate predictions of TPB solubility at the In-Tank Precipitation (ITP) facility. Because previous research showed large deviations in the observed solubility of TPB salts when compared with model predictions, additional data were generated to better understand the solubility of TPB in more complex systems of high ionic strength and those containing both potassium and sodium. These data allow evaluation of the ability of current models to accurately predict equilibrium TPB concentrations over the range of experimental conditions investigated in this study

Silicon induced Fe deficiency affects Fe, Mn, Cu and Zn distribution in rice (Oryza sativa L.) growth in calcareous conditions.

Science.gov (United States)

Carrasco-Gil, Sandra; Rodríguez-Menéndez, Sara; Fernández, Beatriz; Pereiro, Rosario; de la Fuente, Vicenta; Hernandez-Apaolaza, Lourdes

2018-04-01

A protective effect by silicon in the amelioration of iron chlorosis has recently been proved for Strategy 1 species, at acidic pH. However in calcareous conditions, the Si effect on Fe acquisition and distribution is still unknown. In this work, the effect of Si on Fe, Mn, Cu and Zn distribution was studied in rice (Strategy 2 species) under Fe sufficiency and deficiency. Plants (+Si or-Si) were grown initially with Fe, and then Fe was removed from the nutrient solution. The plants were then analysed using a combined approach including LA-ICP-MS images for each element of interest, the analysis of the Fe and Si concentration at different cell layers of root and leaf cross sections by SEM-EDX, and determining the apoplastic Fe, total micronutrient concentration and oxidative stress indexes. A different Si effect was observed depending on plant Fe status. Under Fe sufficiency, Si supply increased Fe root plaque formation, decreasing Fe concentration inside the root and increasing the oxidative stress in the plants. Therefore, Fe acquisition strategies were activated, and Fe translocation rate to the aerial parts was increased, even under an optimal Fe supply. Under Fe deficiency, +Si plants absorbed Fe from the plaque more rapidly than -Si plants, due to the previous activation of Fe deficiency strategies during the growing period (+Fe + Si). Higher Fe plaque formation due to Si supply during the growing period reduced Fe uptake and could activate Fe deficiency strategies in rice, making it more efficient against Fe chlorosis alterations. Silicon influenced Mn and Cu distribution in root. Copyright © 2018 Elsevier Masson SAS. All rights reserved.

Circulating ghrelin, leptin, and soluble leptin receptor concentrations and cardiometabolic risk factors in a community-based sample.

Science.gov (United States)

Ingelsson, Erik; Larson, Martin G; Yin, Xiaoyan; Wang, Thomas J; Meigs, James B; Lipinska, Izabella; Benjamin, Emelia J; Keaney, John F; Vasan, Ramachandran S

2008-08-01

The conjoint effects and relative importance of ghrelin, leptin, and soluble leptin receptor (sOB-R), adipokines involved in appetite control and energy expenditure in mediating cardiometabolic risk, is unknown. The objective of the study was to study the cross-sectional relations of these adipokines to cardiometabolic risk factors in a community-based sample. We measured circulating ghrelin, leptin, and sOB-R in 362 participants (mean age 45 yr; 54% women) of the Framingham Third Generation Cohort. Body mass index, waist circumference (WC), blood pressure, lipid measures, fasting glucose, smoking, and metabolic syndrome (MetS) were measured. Ghrelin and leptin concentrations were significantly higher in women (P risk.

Micro-PIXE evaluation of Fe distribution in barley roots

International Nuclear Information System (INIS)

Schneider, T.; Povh, B.; Strasser, O.; Gierth, M.; Przybylowicz, W.; Mesjasz-Przybylowicz, J.; Churms, C.; Schuessler, A.

1999-01-01

High Fe concentrations were reported from roots of plants grown in soil. This has been discussed as a possible Fe source for plants, since the concentrations shown in the roots were much higher than in the shoots. There are, however, also some indications that soil contamination at the root surface of soil grown plants could have led to an overestimation of the Fe concentration in roots. Fe distribution in root cross sections of barley (Hordeum vulgare L. cv. Alexis) has been studied to investigate this hypothesis. Micro-PIXE analyses in point and mapping mode were complemented by the STIM technique. Based on the correlation between Fe and soil-related elements (Ti, Al and Si), most of Fe located at the root surface could be attributed to soil contamination. It could also be shown that this soil contamination leads to an overestimation of Fe concentration in roots. (author)

Moessbauer study of Fe-Al disordered alloys near the critical concentration

International Nuclear Information System (INIS)

Bohorquez, A.; Tabares, J.A.; Perez Alcazar, G.A.; Gancedo, J.R.

1994-01-01

Disordered bcc Fe 1-q Al q alloys in the composition range 0.5≤q≤0.6 were studied by Moessbauer effect measurements. The Moessbauer spectra at 300 K of all the samples consist of two paramagnetic sites, one is a singlet and the other a doublet with quadrupole splitting. The results can be interpreted by considering that the sites of this disordered system are arranged near the configurations of the Fe and Al sites of the Fe-Al ordered system. (orig.)

Water-soluble metal-binding polymers with ultrafiltration: A technology for the removal, concentration, and recovery of metal ions from aqueous streams

International Nuclear Information System (INIS)

Smith, B.F.; Robison, T.W.; Jarvinen, G.D.

1997-01-01

The use of water-soluble metal-binding polymers coupled with ultrafiltration (UF) is a technology under development to selectively concentrate and recover valuable or regulated metal-ions from dilute process or waste waters. The polymers have a sufficiently large molecular size that they can be separated and concentrated using commercially available UF technology. The polymers can then be reused by changing the solution conditions to release the metal-ions, which are recovered in a concentrated form for recycle or disposal. Pilot-scale demonstrations have been completed for a variety of waste streams containing low concentrations of metal ions including electroplating wastes (zinc and nickel) and nuclear waste streams (plutonium and americium). Many other potential commercial applications exist including remediation of contaminated solids. An overview of both the pilot-scale demonstrated applications and small scale testing of this technology are presented

Water-soluble metal-binding polymers with ultrafiltration: A technology for the removal, concentration, and recovery of metal ions from aqueous streams

Energy Technology Data Exchange (ETDEWEB)

Smith, B.F.; Robison, T.W.; Jarvinen, G.D.

1997-12-31

The use of water-soluble metal-binding polymers coupled with ultrafiltration (UF) is a technology under development to selectively concentrate and recover valuable or regulated metal-ions from dilute process or waste waters. The polymers have a sufficiently large molecular size that they can be separated and concentrated using commercially available UF technology. The polymers can then be reused by changing the solution conditions to release the metal-ions, which are recovered in a concentrated form for recycle or disposal. Pilot-scale demonstrations have been completed for a variety of waste streams containing low concentrations of metal ions including electroplating wastes (zinc and nickel) and nuclear waste streams (plutonium and americium). Many other potential commercial applications exist including remediation of contaminated solids. An overview of both the pilot-scale demonstrated applications and small scale testing of this technology are presented.