A correlation for the quench front velocity in the rewetting of a rod by a falling film

International Nuclear Information System (INIS)

Castiglia, F.; Olivieri, E.; Taibi, S.; Vella, G.

1989-01-01

In recent works the exact analytical solutions to the problem of the steady propagation of the quench front in the rewetting by a falling film of both hot vertical slabs and rods have been presented. These solutions furnish the temperature distribution in the solid and, in particular, the dimensioless sputtering temperature, in terms of the Biot number B and the dimensionless front velocity u. As it is well known, however, in practical applications it result more convenient to deal with an explicit - even if approximate - formula which gives the dimensionless rewetting velocity in terms of B and Θ. In view of this, in the present paper, an extension to the case of rods of a simple and reliable correlation for the prediction of the quench front velocity, already proposed for slabs, is presented. Also in this case, the correlation proves fairly satisfactory and confirms its validity in the full range of practical interest the operating parameters

Microwave solidification project overview

Energy Technology Data Exchange (ETDEWEB)

Sprenger, G.

1993-01-01

The Rocky Flats Plant Microwave Solidification Project has application potential to the Mixed Waste Treatment Project and the The Mixed Waste Integrated Program. The technical areas being addressed include (1) waste destruction and stabilization; (2) final waste form; and (3) front-end waste handling and feed preparation. This document covers need for such a program; technology description; significance; regulatory requirements; and accomplishments to date. A list of significant reports published under this project is included.

Microwave solidification project overview

International Nuclear Information System (INIS)

Sprenger, G.

1993-01-01

The Rocky Flats Plant Microwave Solidification Project has application potential to the Mixed Waste Treatment Project and the The Mixed Waste Integrated Program. The technical areas being addressed include (1) waste destruction and stabilization; (2) final waste form; and (3) front-end waste handling and feed preparation. This document covers need for such a program; technology description; significance; regulatory requirements; and accomplishments to date. A list of significant reports published under this project is included

Solidification behaviors of a single-crystal superalloy under lateral constraints

International Nuclear Information System (INIS)

Zhuangqi Hu; Huaming Wang

1993-01-01

The effect of lateral constraints ahead of solidification interface on the solidification behaviors of a newly developed hot corrosion resistant single-crystal nickel-base superalloy was investigated under commercial single-crystal production conditions. The lateral constraints or section variations ahead of solidification front were found to have drastic influences both on the modes of solidification and the profiles of solute segregation. As lateral constraints were imposed ahead of the directionally solidifying interface, the solidification microstructure of the single-crystal superalloy changed suddenly, through a γ/γ' eutectic-free zone which is characterized by an extremely-fine and highly-developed dendrite network, from the original well-branched dendritic structure to a fine cellular-dendrite or regular cell structure, accompanying which the primary arm spacing, the severity of segregation and the amount of microporosity decreased remarkably. The newly formed cellular dendrite or cell structure transforms always gradually to the initial coarse dendrite structure as the lateral constraint is finally released whether gradually or sharply. Moreover, an abnormal porosity zone was readily observed in the initial section beneath and away from the eutectic-free zone. The solidification microstructural changes were attributed to the drastic dynamical changes in local solidification cooling conditions and in momentum transport during solidification due to the presence of lateral constraint

Bubble velocity in the nonlinear Rayleigh-Taylor instability at a deflagration front

International Nuclear Information System (INIS)

Modestov, Mikhail; Bychkov, Vitaly; Betti, Riccardo; Eriksson, Lars-Erik

2008-01-01

The Rayleigh-Taylor instability at a deflagration front is studied systematically using extensive direct numerical simulations. It is shown that, for a sufficiently large gravitational field, the effects of bubble rising dominate the deflagration dynamics. It is demonstrated both analytically and numerically that the deflagration speed is described asymptotically by the Layzer theory in the limit of large acceleration. In the opposite limit of small and zero gravitational field, intrinsic properties of the deflagration front become important. In that case, the deflagration speed is determined by the velocity of a planar front and by the Darrieus-Landau instability. Because of these effects, the deflagration speed is larger than predicted by the Layzer theory. An analytical formula for the deflagration speed is suggested, which matches two asymptotic limits of large and small acceleration. The formula is in good agreement with the numerical data in a wide range of Froude numbers. The present results are also in agreement with previous numerical simulations on this problem

Simulation study of the ionizing front in the critical ionization velocity phenomenon

International Nuclear Information System (INIS)

Machida, S.; Goertz, C.K.; Lu, G.

1988-01-01

Simulations of the Critical Ionization Velocity (CIV) for a neutral gas cloud moving across the static magnetic field are made. We treat a low-β plasma and use a 2-1/2 D electrostatic code linked with our Plasma and Neutral Interaction Code (PANIC). Our study is focused on the understanding of the interface between the neutral gas cloud and the surrounding plasma where the strong interaction takes place. We assume the existence of some hot electrons in the ambient plasma to provide a seed ionization for CIV. When the ionization starts a sheath-like structure is formed at the surface of the neutral gas (Ionizing Front). In that region the crossfield component of the electric field causes the electron to E x B drift with a velocity of the order of the neutral gas velocity times the square root of the ion to electron mass ratio. Thus the kinetic energy of the drifting electrons can be large enough for electron impact ionization. In addition a diamagnetic drift of the electron occurs due to the number density and temperature inhomogeneity in the ionization front. These drift currents excite the lower-hybrid waves with the wave k-vectors almost perpendicular to the neutral flow and magnetic field again resulting in electron heating and additional ionization. The overall structure is studied by developing a simple analytic model as well as making simulation runs. (author)

Velocity, aerobic power and metabolic cost of whole body and arms only front crawl swimming at various stroke rates.

Science.gov (United States)

Morris, Kirstin S; Osborne, Mark A; Shephard, Megan E; Skinner, Tina L; Jenkins, David G

2016-05-01

Stroke rate (SR) has not been considered in previous research examining the relative roles of the limbs in front-crawl performance. This study compared velocity, aerobic power ([Formula: see text]) and metabolic cost (C) between whole body (WB) and arms only (AO) front-crawl swimming across various intensities while controlling SR. Twenty Australian national swimmers performed six 200 m front-crawl efforts under two conditions: (1) WB swimming and, (2) AO swimming. Participants completed the 200 m trials under three SR conditions: "low" (22-26 stroke-cycles min(-1)), "moderate" (30-34 stroke-cycles min(-1) and "high" (38-42 stroke-cycles min(-1)). [Formula: see text] was continuously measured, with C, velocity, SR, and kick rate calculated for each effort. Regardless of the SR condition and sex, AO velocity was consistently lower than WB velocity by ~11.0 % (p  0.01). When C was expressed as a function of velocity, WB and AO regression equations differed for males (p = 0.01) but not for females (p = 0.087). Kick rate increased as SR increased (p swimming is the same. Coaches should consider these results when prescribing AO sets if their intention is to reduce the metabolic load.

L2 droplet interaction with α-Al during solidification of hypermonotectic Al-8 wt.% Bi alloys

International Nuclear Information System (INIS)

Schaffer, P.L.; Mathiesen, R.H.; Arnberg, L.

2009-01-01

Studies of Al-based hypermonotectics have so far focused mainly on droplet motion and coagulation dynamics, with limited attention given to the interaction between droplets and the advancing solidification front which is decisive for the final distribution of the second phase within the α-Al matrix. The current work presents results from directional solidification experiments with Al-8 wt.% Bi alloys. It was found that droplets with large radii were frequently pushed and small droplets were engulfed. This is contradictory to the many models that have been proposed to explain pushing/engulfment of solid particles and can in part be ascribed to the fact that while solid-particle models only consider single, non-interacting particles that remain unaffected by solutal gradients ahead of the advancing solidification front, droplet-droplet interaction and local solute gradients have been found to be critical for droplet pushing/engulfment behaviour in hypermonotectic alloys.

Matching time and spatial scales of rapid solidification: dynamic TEM experiments coupled to CALPHAD-informed phase-field simulations

Science.gov (United States)

Perron, Aurelien; Roehling, John D.; Turchi, Patrice E. A.; Fattebert, Jean-Luc; McKeown, Joseph T.

2018-01-01

A combination of dynamic transmission electron microscopy (DTEM) experiments and CALPHAD-informed phase-field simulations was used to study rapid solidification in Cu-Ni thin-film alloys. Experiments—conducted in the DTEM—consisted of in situ laser melting and determination of the solidification kinetics by monitoring the solid-liquid interface and the overall microstructure evolution (time-resolved measurements) during the solidification process. Modelling of the Cu-Ni alloy microstructure evolution was based on a phase-field model that included realistic Gibbs energies and diffusion coefficients from the CALPHAD framework (thermodynamic and mobility databases). DTEM and post mortem experiments highlighted the formation of microsegregation-free columnar grains with interface velocities varying from ˜0.1 to ˜0.6 m s-1. After an ‘incubation’ time, the velocity of the planar solid-liquid interface accelerated until solidification was complete. In addition, a decrease of the temperature gradient induced a decrease in the interface velocity. The modelling strategy permitted the simulation (in 1D and 2D) of the solidification process from the initially diffusion-controlled to the nearly partitionless regimes. Finally, results of DTEM experiments and phase-field simulations (grain morphology, solute distribution, and solid-liquid interface velocity) were consistent at similar time (μs) and spatial scales (μm).

Microstructural evolution in Mg-Zn alloys during solidification: An experimental and simulation study

Science.gov (United States)

Paliwal, Manas; Jung, In-Ho

2014-05-01

A comprehensive microstructural evolution of Mg-1.5, 4.0 and 5.5 wt% Zn alloys with respect to the solidification parameters such as thermal gradient (G), solidification velocity (V), cooling rate (GV) and solute (Zn) content were investigated in the present study. Solidification techniques such as directional solidification and wedge casting were employed in order to obtain cooling rates between 0.05 and 250 K/s. Microstructural features such as secondary dendrite arm spacing (SDAS), primary dendrite arm spacing (PDAS), microsegregration along the secondary dendrites and secondary phase fractions were experimentally determined. A solidification model that incorporates solute back diffusion, secondary arm coarsening, dendrite tip undercooling and dynamically linked with accurate thermodynamic databases is used to explain the experimental results.

Overview of the Tusas Code for Simulation of Dendritic Solidification

Energy Technology Data Exchange (ETDEWEB)

Trainer, Amelia J. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Newman, Christopher Kyle [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Francois, Marianne M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-01-07

The aim of this project is to conduct a parametric investigation into the modeling of two dimensional dendrite solidification, using the phase field model. Specifically, we use the Tusas code, which is for coupled heat and phase-field simulation of dendritic solidification. Dendritic solidification, which may occur in the presence of an unstable solidification interface, results in treelike microstructures that often grow perpendicular to the rest of the growth front. The interface may become unstable if the enthalpy of the solid material is less than that of the liquid material, or if the solute is less soluble in solid than it is in liquid, potentially causing a partition [1]. A key motivation behind this research is that a broadened understanding of phase-field formulation and microstructural developments can be utilized for macroscopic simulations of phase change. This may be directly implemented as a part of the Telluride project at Los Alamos National Laboratory (LANL), through which a computational additive manufacturing simulation tool is being developed, ultimately to become part of the Advanced Simulation and Computing Program within the U.S. Department of Energy [2].

Validation of a 3D multi-physics model for unidirectional silicon solidification

NARCIS (Netherlands)

Simons, P.; Lankhorst, A.M.; Habraken, A.; Faber, A.J.; Tiuleanu, D.; Pingel, R.

2012-01-01

A model for transient movements of solidification fronts has been added to X-stream, an existing multi-physics simulation program for high temperature processes with flow and chemical reactions. The implementation uses an enthalpy formulation and works on fixed grids. First we show the results of a

Formation of bands of ultrafine beryllium particles during rapid solidification of Al-Be alloys: Modeling and direct observations

International Nuclear Information System (INIS)

Elmer, J.W.; Tanner, L.E.; Smith, P.M.; Wall, M.A.; Aziz, M.J.

1994-01-01

Rapid solidification of dilute hyper-eutectic and monotectic alloys sometimes produces a dispersion of ultrafine randomly-oriented particles that lie in arrays parallel to the advancing solidification front. The authors characterize this effect in Al-Be where Be-rich particles with diameters on the order of 10 nm form in arrays spaced approximately 25 nm apart, and they present a model of macroscopically steady state but microscopically oscillatory motion of the solidification front to explain this unusual microstructure. The proposed mechanism involves; (i) the build-up of rejected solute in a diffusional boundary layer which slows down the growing crystal matrix, (2) the boundary layer composition entering a metastable liquid miscibility gap, (3) homogeneous nucleation of solute rich liquid droplets in the boundary layer, and crystallization of these droplets, and (4) growth of the matrix past the droplets and its reformation into a planar interface. The size of the Be-rich particles is limited by the beryllium supersaturation in the diffusional boundary layer. A numerical model was developed to investigate this solidification mechanism, and the results of the model are in good agreement with experimental observations of rapidly solidified Al-5 at.% Be

A Real Time Investigation of Morphological Evolution During Solidification of Different Alloy Systems

Science.gov (United States)

Sen, S.; Kaukler, W. F.; Curreri, P. A.

1999-01-01

between undercooling and growth velocity during plane front growth, marginal stability regime, and stable cellular growth.

Photoionization effects in ionization fronts

International Nuclear Information System (INIS)

Arrayas, Manuel; Fontelos, Marco A; Trueba, Jose L

2006-01-01

In this paper we study the effects of photoionization processes on the propagation of both negative and positive ionization fronts in streamer discharge. We show that negative fronts accelerate in the presence of photoionization events. The appearance and propagation of positive ionization fronts travelling with constant velocity is explained as the result of the combined effects of photoionization and electron diffusion. The photoionization range plays an important role in the selection of the velocity of the ionization front as we show in this work

Photoionization effects in ionization fronts

Energy Technology Data Exchange (ETDEWEB)

Arrayas, Manuel [Departamento de Electromagnetismo, Universidad Rey Juan Carlos, Tulipan s/n, 28933 Mostoles, Madrid (Spain); Fontelos, Marco A [Departamento de Matematicas, Instituto de Matematicas y Fisica Fundamental, Consejo Superior de Investigaciones CientIficas, C/Serrano 123, 28006 Madrid (Spain); Trueba, Jose L [Departamento de Electromagnetismo, Universidad Rey Juan Carlos, Tulipan s/n, 28933 Mostoles, Madrid (Spain)

2006-12-21

In this paper we study the effects of photoionization processes on the propagation of both negative and positive ionization fronts in streamer discharge. We show that negative fronts accelerate in the presence of photoionization events. The appearance and propagation of positive ionization fronts travelling with constant velocity is explained as the result of the combined effects of photoionization and electron diffusion. The photoionization range plays an important role in the selection of the velocity of the ionization front as we show in this work.

Interface stability during rapid directional solidification

International Nuclear Information System (INIS)

Hoglund, D.E.; Aziz, M.J.

1992-01-01

This paper reports that at the solidification velocities observed during pulsed laser annealing, the planar interface between solid and liquid is stabilized by capillarity and nonequilibrium effects such as solute trapping. The authors used Rutherford backscattering and electron microscopy to determine the nonequilibrium partition coefficient and critical concentration for breakdown of the planar interface as a function of interface velocity for Sn-implanted silicon. This allows the authors to test the applicability of the Mulliins-Sekerka stability theory to interfaces not in local equilibrium and to test the Coriell-Sekerka and other theories for oscillatory instabilities

Numerical simulation of solute trapping phenomena using phase-field solidification model for dilute binary alloys

Directory of Open Access Journals (Sweden)

Henrique Silva Furtado

2009-09-01

Full Text Available Numerical simulation of solute trapping during solidification, using two phase-field model for dilute binary alloys developed by Kim et al. [Phys. Rev. E, 60, 7186 (1999] and Ramirez et al. [Phys. Rev. E, 69, 05167 (2004] is presented here. The simulations on dilute Cu-Ni alloy are in good agreement with one dimensional analytic solution of sharp interface model. Simulation conducted under small solidification velocity using solid-liquid interface thickness (2λ of 8 nanometers reproduced the solute (Cu equilibrium partition coefficient. The spurious numerical solute trapping in solid phase, due to the interface thickness was negligible. A parameter used in analytical solute trapping model was determined by isothermal phase-field simulation of Ni-Cu alloy. Its application to Si-As and Si-Bi alloys reproduced results that agree reasonably well with experimental data. A comparison between the three models of solute trapping (Aziz, Sobolev and Galenko [Phys. Rev. E, 76, 031606 (2007] was performed. It resulted in large differences in predicting the solidification velocity for partition-less solidification, indicating the necessity for new and more acute experimental data.

Columnar and Equiaxed Solidification of Al-7 wt.% Si Alloys in Reduced Gravity in the Framework of the CETSOL Project

Science.gov (United States)

Zimmermann, G.; Sturz, L.; Nguyen-Thi, H.; Mangelinck-Noel, N.; Li, Y. Z.; Gandin, C.-A.; Fleurisson, R.; Guillemot, G.; McFadden, S.; Mooney, R. P.; Voorhees, P.; Roosz, A.; Ronaföldi, A.; Beckermann, C.; Karma, A.; Chen, C.-H.; Warnken, N.; Saad, A.; Grün, G.-U.; Grohn, M.; Poitrault, I.; Pehl, T.; Nagy, I.; Todt, D.; Minster, O.; Sillekens, W.

2017-08-01

During casting, often a dendritic microstructure is formed, resulting in a columnar or an equiaxed grain structure, or leading to a transition from columnar to equiaxed growth (CET). The detailed knowledge of the critical parameters for the CET is important because the microstructure affects materials properties. To provide unique data for testing of fundamental theories of grain and microstructure formation, solidification experiments in microgravity environment were performed within the European Space Agency Microgravity Application Promotion (ESA MAP) project Columnar-to-Equiaxed Transition in SOLidification Processing (CETSOL). Reduced gravity allows for purely diffusive solidification conditions, i.e., suppressing melt flow and sedimentation and floatation effects. On-board the International Space Station, Al-7 wt.% Si alloys with and without grain refiners were solidified in different temperature gradients and with different cooling conditions. Detailed analysis of the microstructure and the grain structure showed purely columnar growth for nonrefined alloys. The CET was detected only for refined alloys, either as a sharp CET in the case of a sudden increase in the solidification velocity or as a progressive CET in the case of a continuous decrease of the temperature gradient. The present experimental data were used for numerical modeling of the CET with three different approaches: (1) a front tracking model using an equiaxed growth model, (2) a three-dimensional (3D) cellular automaton-finite element model, and (3) a 3D dendrite needle network method. Each model allows for predicting the columnar dendrite tip undercooling and the growth rate with respect to time. Furthermore, the positions of CET and the spatial extent of the CET, being sharp or progressive, are in reasonably good quantitative agreement with experimental measurements.

Modélisation de la solidification par la méthode d’enthalpie

OpenAIRE

BENAMEUR, Benamar

2014-01-01

La modélisation numérique du phénomène de solidification à l’échelle macroscopique a une importance considérable dans la conception virtuelle des procédés d’élaboration des matériaux. Ce phénomène de solidification est caractérisé par la formation d’une frontière mobile qui sépare les deux phases liquide et solide au cours de changement de phase, ce qui nécessite des techniques appropriées pour suivre le mouvement de front et localiser sa position. Dans ce mémoire et afin de...

Modélisation de la solidification par la méthode d’enthalpie

OpenAIRE

BENAMEUR, Benamar

2013-01-01

La modélisation numérique du phénomène de solidification à l’échelle macroscopique a une importance considérable dans la conception virtuelle des procédés d’élaboration des matériaux. Ce phénomène de solidification est caractérisé par la formation d’une frontière mobile qui sépare les deux phases liquide et solide au cours de changement de phase, ce qui nécessite des techniques appropriées pour suivre le mouvement de front et localiser sa position. Dans ce mémoire et afin de...

The effects of solidification on sill propagation dynamics and morphology

Science.gov (United States)

Chanceaux, L.; Menand, T.

2016-05-01

Sills are an integral part of the formation and development of larger plutons and magma reservoirs. Thus sills are essential for both the transport and the storage of magma in the Earth's crust. However, although cooling and solidification are central to magmatism, their effects on sills have been so far poorly studied. Here, the effects of solidification on sill propagation dynamics and morphology are studied by means of analogue laboratory experiments. Hot fluid vegetable oil (magma analogue), that solidifies during its propagation, is injected as a sill in a colder layered gelatine solid (elastic host rock analogue). The injection flux and temperature are maintained constant during an experiment and systematically varied between each experiment, in order to vary and quantify the amount of solidification between each experiments. The oil is injected directly at the interface between the two gelatine layers. When solidification effects are small (high injection temperatures and fluxes), the propagation is continuous and the sill has a regular and smooth surface. Inversely, when solidification effects are important (low injection temperatures and fluxes), sill propagation is discontinuous and occurs by steps of surface-area creation interspersed with periods of momentary arrest. The morphology of these sills displays folds, ropy structures on their surface, and lobes with imprints of the leading fronts that correspond to each step of area creation. These experiments show that for a given, constant injected volume, as solidification effects increase, the area of the sills decreases, their thickness increases, and the number of propagation steps increases. These results have various geological and geophysical implications. The morphology of sills, such as lobate structures (interpretation of 3D seismic studies in sedimentary basin) and ropy flow structures (field observations) can be related to solidification during emplacement. Moreover, a non-continuous morphology

A scaling analysis of alloy solidification in presence of electromagnetic stirring

International Nuclear Information System (INIS)

Kumar, Arvind; Dutta, Pradip

2006-01-01

Application of electromagnetic stirring (EMS) during continuous casting shears off the dendrites from the solidification front to produce billets with a non-dendritic microstructure. In the present study, a systematic approach to the scaling analysis of momentum, energy and species conservation equations pertaining to the case of the solidification of a binary alloy in the presence of EMS is outlined. With suitable choices of non-dimensionalizing parameters, the governing equations coupled with appropriate boundary conditions are first scaled, and then the relative significance of various terms appearing in them are analysed. In the physical domain two regions are identified, one where the electromagnetic forces play a dominant role in the momentum equations, and the other where the inertia and viscous effects play major roles. Using the scaling predictions, the influence of various processing parameters on the system variables can be utilized for the selection of appropriate electromagnetic forces to shear off the dendrites from the solidification area. For the sake of assessment of the scaling analysis, the predictions are validated against corresponding computational results

Diffusion-stress coupling in liquid phase during rapid solidification of binary mixtures

International Nuclear Information System (INIS)

Sobolev, S.L.

2014-01-01

An analytical model has been developed to describe the diffusion-viscous stress coupling in the liquid phase during rapid solidification of binary mixtures. The model starts with a set of evolution equations for diffusion flux and viscous pressure tensor, based on extended irreversible thermodynamics. It has been demonstrated that the diffusion-stress coupling leads to non-Fickian diffusion effects in the liquid phase. With only diffusive dynamics, the model results in the nonlocal diffusion equations of parabolic type, which imply the transition to complete solute trapping only asymptotically at an infinite interface velocity. With the wavelike dynamics, the model leads to the nonlocal diffusion equations of hyperbolic type and describes the transition to complete solute trapping and diffusionless solidification at a finite interface velocity in accordance with experimental data and molecular dynamic simulation. -- Highlights: •We propose the diffusion-stress coupling model for binary solidification. •The coupling arises at deep undercooling. •With diffusive dynamics, the models result in parabolic transfer equations. •With the wavelike dynamics, the models lead to hyperbolic transfer equations. •The coupling strongly affects the solute partition coefficient

Numerical simulation of convection and inclusion distribution during solidification in a heavy steel ingot

International Nuclear Information System (INIS)

Lin, Rui; Shen, Houfa

2015-01-01

Inclusions content in the steel ingot is an important index for homogeneity, and it becomes more serious for heavy steel ingots which are used for major equipment. However, knowledge about the formation of inclusion in steel ingot is limited, and modeling of inclusion distribution is still challenging, so it is of great significance to research the behavior of inclusion. In this paper, fluid flow during solidification is numerically simulated based on the equilibrium equations of mass, momentum and energy, and then inclusion distribution is modeled according to the Lagrangian Stokes trajectory method. The Results show that the inclusion distribution in the steel ingot is influenced by the flow pattern which is affected by the solidification pattern. Therefore, inclusion distribution could be controlled by the solidification front with the optimization of heat transfer condition such as the hot top design of steel ingot for the high quality steel production. (paper)

Thermosolutal convection during dendritic solidification

Science.gov (United States)

Heinrich, J. C.; Nandapurkar, P.; Poirier, D. R.; Felicelli, S.

1989-01-01

This paper presents a mathematical model for directional solidification of a binary alloy including a dendritic region underlying an all-liquid region. It is assumed initially that there exists a nonconvecting state with planar isotherms and isoconcentrates solidifying at a constant velocity. The stability of this system has been analyzed and nonlinear calculations are performed that show the effect of convection in the solidification process when the system is unstable. Results of calculations for various cases defined by the initial temperature gradient at the dendrite tips and varying strength of the gravitational field are presented for systems involving lead-tin alloys. The results show that the systems are stable for a gravitational constant of 0.0001 g(0) and that convection can be suppressed by appropriate choice of the container's size for higher values of the gravitational constant. It is also concluded that for the lead-tin systems considered, convection in the mushy zone is not significant below the upper 20 percent of the dendritic zone, if al all.

Comparative study of solute trapping and Gibbs free energy changes at the phase interface during alloy solidification under local nonequilibrium conditions

Energy Technology Data Exchange (ETDEWEB)

Sobolev, S. L., E-mail: sobolev@icp.ac.ru [Russian Academy of Sciences, Institute of Problems of Chemical Physics (Russian Federation)

2017-03-15

An analytical model has been developed to describe the influence of solute trapping during rapid alloy solidification on the components of the Gibbs free energy change at the phase interface with emphasis on the solute drag energy. For relatively low interface velocity V < V{sub D}, where V{sub D} is the characteristic diffusion velocity, all the components, namely mixing part, local nonequilibrium part, and solute drag, significantly depend on solute diffusion and partitioning. When V ≥ V{sub D}, the local nonequilibrium effects lead to a sharp transition to diffusionless solidification. The transition is accompanied by complete solute trapping and vanishing solute drag energy, i.e. partitionless and “dragless” solidification.

Positive segregation as a function of buoyancy force during steel ingot solidification

International Nuclear Information System (INIS)

Radovic, Zarko; Jaukovic, Nada; Lalovic, Milisav; Tadic, Nebojsa

2008-01-01

We analyze theoretically and experimentally solute redistribution in the dendritic solidification process and positive segregation during solidification of steel ingots. Positive segregation is mainly caused by liquid flow in the mushy zone. Changes in the liquid steel velocity are caused by the temperature gradient and by the increase in the solid fraction during solidification. The effects of buoyancy and of the change in the solid fraction on segregation intensity are analyzed. The relationships between the density change, liquid fraction and the steel composition are considered. Such elements as W, Ni, Mo and Cr decrease the effect of the density variations, i.e. they show smaller tendency to segregate. Based on the modeling and experimental results, coefficients are provided controlling the effects of chemical composition, secondary dendrite arm spacing and the solid fraction.

Variations of Microsegregation and Second Phase Fraction of Binary Mg-Al Alloys with Solidification Parameters

Science.gov (United States)

Paliwal, Manas; Kang, Dae Hoon; Essadiqi, Elhachmi; Jung, In-Ho

2014-07-01

A systematic experimental investigation on microsegregation and second phase fraction of Mg-Al binary alloys (3, 6, and 9 wt pct Al) has been carried out over a wide range of cooling rates (0.05 to 700 K/s) by employing various casting techniques. In order to explain the experimental results, a solidification model that takes into account dendrite tip undercooling, eutectic undercooling, solute back diffusion, and secondary dendrite arm coarsening was also developed in dynamic linkage with an accurate thermodynamic database. From the experimental data and solidification model, it was found that the second phase fraction in the solidified microstructure is not determined only by cooling rate but varied independently with thermal gradient and solidification velocity. Lastly, the second phase fraction maps for Mg-Al alloys were calculated from the solidification model.

Effect of Sr and solidification conditions on characteristics of intermetallic in Al-Si 319 industrial alloys

International Nuclear Information System (INIS)

Espinoza-Cuadra, J.; Gallegos-Acevedo, P.; Mancha-Molinar, H.; Picado, A.

2010-01-01

An experimental study was carried out to determine the effect of strontium (Sr) on the characteristic of intermetallic phases, particularly the Al 5 FeSi phase which present morphology of platelets or needle-like. The results showed that within the range of variables studied, the modification process caused the disappearance of the needles and only occur the precipitation of phase α (chinese script-like). Refinement of the intermetallic phases occurs in conjunction with the refinement in grain size. Both parameters depend strongly on local cooling rate (T), temperature gradient (G) and apparent rate of solidification front (V). In the case of equiaxed structures the refinement of grain size and intermetallic occurs with increasing local cooling rate and temperature gradient and decrease the apparent rate of solidification front. In the case of columnar structures, refinement of grains and intermetallic requires the increase in values of the three variables indicated. Moreover, the addition of Sr resulted in the modification of silicon eutectic, as noted in others research works.

Simulation of the solidification in a channel of a water-cooled glass flow

Directory of Open Access Journals (Sweden)

G. E. Ovando Chacon

2014-12-01

Full Text Available A computer simulation study of a laminar steady-state glass flow that exits from a channel cooled with water is reported. The simulations are carried out in a two-dimensional, Cartesian channel with a backward-facing step for three different angles of the step and different glass outflow velocities. We studied the interaction of the fluid dynamics, phase change and thermal behavior of the glass flow due to the heat that transfers to the cooling water through the wall of the channel. The temperature, streamline, phase change and pressure fields are obtained and analyzed for the glass flow. Moreover, the temperature increments of the cooling water are characterized. It is shown that, by reducing the glass outflow velocity, the solidification is enhanced; meanwhile, an increase of the step angle also improves the solidification of the glass flow.

In-situ solidification cleans up old gas plant site

International Nuclear Information System (INIS)

Hatfield, A.D.; Dennis, N.D.

1995-01-01

A manufactured gas plant site in Columbus, Georgia, was the location of an environmental cleanup in 1992. Manufactured gas was produced at this site from 1854 to 1931 with the availability of natural gas from a transmission pipeline causing its demise. However, waste products, primarily coal tar from the earlier years of plant operation, remained with the site. In-situ solidification was chosen as the cleanup method. Post monitoring activities show that the project was successful and the site is now a park and a leading part of river front development

Phase selection and microstructure in directional solidification of glass forming Pd-Si-Cu alloys

Science.gov (United States)

Huo, Yang

Phase selection and microstructure formation during the rapid solidification of alloy melts has been a topic of substantial interest over the last several decades, attributed mainly to the access to novel structures involving metastable crystalline and non-crystalline phases. In this work, Bridgeman type directional solidification was conducted in Pd-Si-Cu glass forming system to study such cooling rate dependent phase transition and microstructure formation. The equilibrium state for Pd-Si-Cu ternary system was investigated through three different works. First of all, phase stabilities for Pd-Si binary system was accessed with respects of first-principles and experiments, showing Pd5Si, Pd9Si2, Pd3Si and Pd 2Si phase are stable all way to zero Kevin while PdSi phase is a high temperature stable phase, and Pd2Si phase with Fe2P is a non-stoichiometry phase. A thermodynamic database was developed for Pd-Si system. Second, crystal structures for compounds with ternary compositions were studied by XRD, SEM and TEM, showing ordered and disordered B2/bcc phases are stable in Pd-rich part. At last, based on many phase equilibria and phase transitions data, a comprehensive thermodynamic discrption for Pd-Si-Cu ternary system was first time to be developed, from which different phase diagrams and driving force for kinetics can be calculated. Phase selection and microstructure formation in directional solidification of the best glass forming composition, Pd 77.5Si16.5Cu6, in this system with growth velocities from 0.005 to 7.5mm/s was systematically studied and the solidification pathways at different conditions were interpreted from thermodynamic simulation. The results show that for growth velocities are smaller than 0.1mm/s Pd 3Si phase is primary phase and Pd9Si2 phase is secondary phase, the difficulty for Pd9Si2 phase nucleation gives rise to the formation of two different eutectic structure. For growth velocities between 0.4 and 1mm/s, instead of Pd3Si phase, Pd9Si2

Collective cell migration without proliferation: density determines cell velocity and wave velocity

Science.gov (United States)

Tlili, Sham; Gauquelin, Estelle; Li, Brigitte; Cardoso, Olivier; Ladoux, Benoît; Delanoë-Ayari, Hélène; Graner, François

2018-05-01

Collective cell migration contributes to embryogenesis, wound healing and tumour metastasis. Cell monolayer migration experiments help in understanding what determines the movement of cells far from the leading edge. Inhibiting cell proliferation limits cell density increase and prevents jamming; we observe long-duration migration and quantify space-time characteristics of the velocity profile over large length scales and time scales. Velocity waves propagate backwards and their frequency depends only on cell density at the moving front. Both cell average velocity and wave velocity increase linearly with the cell effective radius regardless of the distance to the front. Inhibiting lamellipodia decreases cell velocity while waves either disappear or have a lower frequency. Our model combines conservation laws, monolayer mechanical properties and a phenomenological coupling between strain and polarity: advancing cells pull on their followers, which then become polarized. With reasonable values of parameters, this model agrees with several of our experimental observations. Together, our experiments and model disantangle the respective contributions of active velocity and of proliferation in monolayer migration, explain how cells maintain their polarity far from the moving front, and highlight the importance of strain-polarity coupling and density in long-range information propagation.

The melting and solidification of nanowires

International Nuclear Information System (INIS)

Florio, B. J.; Myers, T. G.

2016-01-01

A mathematical model is developed to describe the melting of nanowires. The first section of the paper deals with a standard theoretical situation, where the wire melts due to a fixed boundary temperature. This analysis allows us to compare with existing results for the phase change of nanospheres. The equivalent solidification problem is also examined. This shows that solidification is a faster process than melting; this is because the energy transfer occurs primarily through the solid rather than the liquid which is a poorer conductor of heat. This effect competes with the energy required to create new solid surface which acts to slow down the process, but overall conduction dominates. In the second section, we consider a more physically realistic boundary condition, where the phase change occurs due to a heat flux from surrounding material. This removes the singularity in initial melt velocity predicted in previous models of nanoparticle melting. It is shown that even with the highest possible flux the melting time is significantly slower than with a fixed boundary temperature condition.

The melting and solidification of nanowires

Science.gov (United States)

Florio, B. J.; Myers, T. G.

2016-06-01

A mathematical model is developed to describe the melting of nanowires. The first section of the paper deals with a standard theoretical situation, where the wire melts due to a fixed boundary temperature. This analysis allows us to compare with existing results for the phase change of nanospheres. The equivalent solidification problem is also examined. This shows that solidification is a faster process than melting; this is because the energy transfer occurs primarily through the solid rather than the liquid which is a poorer conductor of heat. This effect competes with the energy required to create new solid surface which acts to slow down the process, but overall conduction dominates. In the second section, we consider a more physically realistic boundary condition, where the phase change occurs due to a heat flux from surrounding material. This removes the singularity in initial melt velocity predicted in previous models of nanoparticle melting. It is shown that even with the highest possible flux the melting time is significantly slower than with a fixed boundary temperature condition.

The melting and solidification of nanowires

Energy Technology Data Exchange (ETDEWEB)

Florio, B. J., E-mail: brendan.florio@ul.ie [University of Limerick, Mathematics Applications Consortium for Science and Industry (MACSI), Department of Mathematics and Statistics (Ireland); Myers, T. G., E-mail: tmyers@crm.cat [Centre de Recerca Matemàtica (Spain)

2016-06-15

A mathematical model is developed to describe the melting of nanowires. The first section of the paper deals with a standard theoretical situation, where the wire melts due to a fixed boundary temperature. This analysis allows us to compare with existing results for the phase change of nanospheres. The equivalent solidification problem is also examined. This shows that solidification is a faster process than melting; this is because the energy transfer occurs primarily through the solid rather than the liquid which is a poorer conductor of heat. This effect competes with the energy required to create new solid surface which acts to slow down the process, but overall conduction dominates. In the second section, we consider a more physically realistic boundary condition, where the phase change occurs due to a heat flux from surrounding material. This removes the singularity in initial melt velocity predicted in previous models of nanoparticle melting. It is shown that even with the highest possible flux the melting time is significantly slower than with a fixed boundary temperature condition.

Hydraulic experiment on evaluation method of tsunami wave pressure using inundation depth and velocity in front of land structure

International Nuclear Information System (INIS)

Arimitsu, Tsuyoshi; Ooe, Kazuya; Kawasaki, Koji

2012-01-01

Hydraulic experiments were conducted to estimate tsunami wave pressure acting on several different types of land structures and examine the influence of a seawall in front of the structure on tsunami wave pressure. Wave pressures were measured at some points on the structure. The existing hydrostatic formula tended to underestimate tsunami wave pressure under the condition of inundation flow with large Froude number. Estimation method of tsunami wave pressure using inundation depth and horizontal velocity at the front of the structure was proposed based on the experimental results. It was confirmed from comparison with the experiments that the vertical distribution of the maximum tsunami wave pressure can be reproduced by employing the proposed method in this study. (author)

Radioactive gas solidification apparatus

International Nuclear Information System (INIS)

Kobayashi, Yoshihiro; Seki, Eiji; Yabu, Tomohiko; Matsunaga, Hiroyuki.

1990-01-01

Handling of a solidification container from the completion for the solidifying processing to the storage of radioactive gases by a remote control equipment such as a manipulator requires a great cost and is difficult to realize. In a radioactive gas solidification device for injection and solidification in accumulated layers of sputtered metals by glow discharge, radiation shieldings are disposed surrounding the entire container, and cooling water is supplied to a cooling vessel formed between the container and the shielding materials. The shielding materials are divided into upper and lower shielding materials, so that solidification container can be taken out from the shielding materials. As a result, the solidification container after the solidification of radioactive gases can be handled with ease. Further, after-heat can be removed effectively from the ion injection electrode upon solidifying treatment upon storage, to attain a radioactive gas solidifying processing apparatus which is safe, economical and highly reliable. (N.H.)

Dendritic solidification in undercooled Ni-Zr-Al melts: Experiments and modeling

Energy Technology Data Exchange (ETDEWEB)

Galenko, P.K., E-mail: Peter.Galenko@dlr.de [Institut fuer Materialsphysik im Weltraum, Deutsches Zentrum fuer Luft- und Raumfahrt (DLR), D-51170 Koeln (Germany); Reutzel, S.; Herlach, D.M. [Institut fuer Materialsphysik im Weltraum, Deutsches Zentrum fuer Luft- und Raumfahrt (DLR), D-51170 Koeln (Germany); Fries, S.G. [ICAMS, Ruhr-Universitaet Bochum, Stiepeler Strasse 129, D-44780 Bochum (Germany)] [SGF Scientific Consultancy, Arndtstr 9, D-52064 Aachen (Germany); Steinbach, I. [ICAMS, Ruhr-Universitaet Bochum, Stiepeler Strasse 129, D-44780 Bochum (Germany); Apel, M. [ACCESS eV, Intzestrasse 5, D-52072 Aachen (Germany)

2009-12-15

The kinetics of dendritic solidification in a ternary Ni{sub 98}Zr{sub 1}Al{sub 1} alloy is investigated experimentally in a range of melt undercoolings 40K{<=}{Delta}T{<=}320K. The growth velocity is measured for samples processed by the electromagnetic levitation technique using a high-speed video camera. With {Delta}T{<=}220K the measured growth rates are the same as those of a binary Ni{sub 99}Zr{sub 1} alloy. In the regime of rapid solidification, especially within the regime of thermal dendritic growth at {Delta}T{>=}220K, growth rates are decreased. Sharp-interface modeling predicts growth rates over the whole range of undercooling. Phase-field simulations give quantitative predictions for the dendritic growth velocity in the solute-controlled growth regime. Results show that the composition and temperature dependency of the thermodynamic data, e.g. liquidus slope and solute partition coefficient, are important for describing the alloys. Our findings give improved sharp-interface model predictions compared to calculations based on an approximation of the thermodynamic data derived from binary phase diagrams.

Microstructural Development in Al-Si Powder During Rapid Solidification

Energy Technology Data Exchange (ETDEWEB)

Genau, Amber Lynn [Iowa State Univ., Ames, IA (United States)

2004-01-01

Powder metallurgy has become an increasingly important form of metal processing because of its ability to produce materials with superior mechanical properties. These properties are due in part to the unique and often desirable microstructures which arise as a result of the extreme levels of undercooling achieved, especially in the finest size powder, and the subsequent rapid solidification which occurs. A better understanding of the fundamental processes of nucleation and growth is required to further exploit the potential of rapid solidification processing. Aluminum-silicon, an alloy of significant industrial importance, was chosen as a model for simple eutectic systems displaying an unfaceted/faceted interface and skewed coupled eutectic growth zone, Al-Si powder produced by high pressure gas atomization was studied to determine the relationship between microstructure and alloy composition as a function of powder size and atomization gas. Critical experimental measurements of hypereutectic (Si-rich) compositions were used to determine undercooling and interface velocity, based on the theoretical models which are available. Solidification conditions were analyzed as a function of particle diameter and distance from nucleation site. A revised microstructural map is proposed which allows the prediction of particle morphology based on temperature and composition. It is hoped that this work, by providing enhanced understanding of the processes which govern the development of the solidification morphology of gas atomized powder, will eventually allow for better control of processing conditions so that particle microstructures can be optimized for specific applications.

A computational/directional solidification method to establish saddle points on the Mg-Al-Ca liquidus

International Nuclear Information System (INIS)

Cao Hongbo; Zhang Chuan; Zhu Jun; Cao Guoping; Kou Sindo; Schmid-Fetzer, Rainer; Chang, Y. Austin

2008-01-01

We established two saddle point maxima, L + α(Mg) + C14 and L + α(Mg) + C36, on the monovariant liquidus, calculated from a previously presented thermodynamic description, by characterizing the microstructures of several directionally solidified alloys in the near-solidification front zone, the mushy zone, and the steady-state zone using optical microscopy, scanning electron microscopy and transmission electron microscopy

Solidification at the High and Low Rate Extreme

Energy Technology Data Exchange (ETDEWEB)

Meco, Halim [Iowa State Univ., Ames, IA (United States)

2004-12-19

The microstructures formed upon solidification are strongly influenced by the imposed growth rates on an alloy system. Depending on the characteristics of the solidification process, a wide range of growth rates is accessible. The prevailing solidification mechanisms, and thus the final microstructure of the alloy, are governed by these imposed growth rates. At the high rate extreme, for instance, one can have access to novel microstructures that are unattainable at low growth rates. While the low growth rates can be utilized for the study of the intrinsic growth behavior of a certain phase growing from the melt. Although the length scales associated with certain processes, such as capillarity, and the diffusion of heat and solute, are different at low and high rate extremes, the phenomena that govern the selection of a certain microstructural length scale or a growth mode are the same. Consequently, one can analyze the solidification phenomena at both high and low rates by using the same governing principles. In this study, we examined the microstructural control at both low and high extremes. For the high rate extreme, the formation of crystalline products and factors that control the microstructure during rapid solidification by free-jet melt spinning are examined in Fe-Si-B system. Particular attention was given to the behavior of the melt pool at different quench-wheel speeds. Since the solidification process takes place within the melt-pool that forms on the rotating quench-wheel, we examined the influence of melt-pool dynamics on nucleation and growth of crystalline solidification products and glass formation. High-speed imaging of the melt-pool, analysis of ribbon microstructure, and measurement of ribbon geometry and surface character all indicate upper and lower limits for melt-spinning rates for which nucleation can be avoided, and fully amorphous ribbons can be achieved. Comparison of the relevant time scales reveals that surface-controlled melt

Two-dimensional multi-scale dendrite needle network modeling and x-ray radiography of equiaxed alloy solidification in grain-refined Al-3.5 wt-%Ni

International Nuclear Information System (INIS)

Sturz, Laszlo; Theofilatos, Angelos

2016-01-01

The aim of this work is to investigate multiple dendritic equiaxed grain formation during directional solidification of grain-refined Al-3.5 wt-%Ni under a range of different solidification conditions. This is achieved by comparing the results of in-situ x-ray radiographic experiments involving thin samples (as reported in the literature) to the results of 2D multi-scale dendrite needle network (DNN) modeling covering the essential experimental length scale. The model takes into account heterogeneous nucleation, branched dendritic growth and solutal interaction between branches and multiple equiaxed grains. The decrease in equivalent circular diameter of the steady-state average grain size with pulling velocity, as observed in the Bridgman-type experiments, is well captured by the modeling results, and likewise the ratio of activated nucleation seeds. Using experimentally estimated nucleation parameters in the modeling, a log normal nucleation undercooling distribution provided slightly but not significantly better agreement with experiments than a Gaussian distribution, with remaining absolute differences in the equivalent circular diameter of up to 31%. Thus, even with the 2D modeling of an essentially 3D experiment, fairly good agreement is achieved. This is attributed to a solutal undercooling of the equiaxed front region in the modeling which is similar in comparison to the dendrite tip undercooling predicted by an analytical 3D calculation, on which the estimation of nucleation parameters was based. Moreover, dendrite side-branching in modeling is of minor impact, due to a ratio between solutal diffusion length and equivalent circular diameter inferior to 0.49 under all solidification conditions. Additionally, at low pulling velocities, the computed grain density is only slightly dependent on which unknown dendrite selection parameter σ* over a wider range is selected. On the other hand, at high pulling velocities there is no dependence. In short

Inspection method for solidification product of radioactive waste and method of preparing solidification product of radiation waste

International Nuclear Information System (INIS)

Izumida, Tatsuo; Tamada, Shin; Matsuda, Masami; Kamata, Shoji; Kikuchi, Makoto.

1993-01-01

A powerful X-ray generation device using an electron-ray accelerator is used for inspecting presence or absence of inner voids in solidification products of radioactive wastes during or after solidification. By installing the X-ray CT system and the radioactive waste solidifying facility together, CT imaging for solidification products is conducted in a not-yet cured state of solidifying materials during or just after the injection. If a defect that deteriorates the durability of the solidification products should be detected, the solidification products are repaired, for example, by applying vibrations to the not-yet cured solidification products. Thus, since voids or cracks in the radioactive wastes solidification products, which were difficult to be measured so far, can be measured in a short period of time accurately thereby enabling to judge adaptability to the disposal standards, inspection cost for the radioactive waste solidification product can be saved remarkably. Further, the inside of the radioactive waste solidification products can be evaluated correctly and visually, so that safety in the ground disposal storage of the radioactive solidification products can be improved remarkably. (N.H.)

Radioactive gas solidification treatment device

International Nuclear Information System (INIS)

Igarashi, Ryokichi; Watanabe, Yu; Seki, Eiji.

1992-01-01

In a radioactive gas solidification treatment device by using sputtering, spiral pipelines are disposed with a gap therebetween for cooling an ion injection electrode by passing cooling water during operation of the solidification treatment. During the operation of the solidification treatment, cooling water is passed in the pipelines to cool the ion injection electrode. During storage, a solidification vessel is cooled by natural heat dissipation from an exposed portion at the surface of the solidification vessel. Accordingly, after-heat of radioactive gas solidified in a metal accumulation layer can be removed efficiently, safely and economically to improve the reliability. (N.H.)

Low-level radwaste solidification

International Nuclear Information System (INIS)

Naughton, M.D.; Miller, C.C.; Nelson, R.A.; Tucker, R.F.

1983-01-01

This paper reports on a study of ''Advanced Low-Level Radioactive Waste Treatment Systems'' conducted under an EPRI contract. The object of the study is to identify advanced lowlevel radwaste treatment systems that are commercially available or are expected to be in the near future. The current state-ofthe-art in radwaste solidification technology is presented. Related processing technologies, such as the compaction of dry active waste (DAW), containers available for radwaste disposal, and the regulatory aspects of radwaste transportation and solidification, are described. The chemical and physical properties of the currently acceptable solidification agents, as identified in the Barnwell radwaste burial site license, are examined. The solidification agents investigated are hydraulic cements, thermoplastic polymers, and thermosetting polymers. It is concluded that solidification processes are complex and depend not only on the chemical and physical properties of the binder material and the waste, but also on how these materials are mixed

Solidification method of radioactive wastes

Energy Technology Data Exchange (ETDEWEB)

Baba, Tsutomu; Chino, Koichi; Sasahira, Akira; Ikeda, Takashi

1992-07-24

Metal solidification material can completely seal radioactive wastes and it has high sealing effect even if a trace amount of evaporation should be caused. In addition, the solidification operation can be conducted safely by using a metal having a melting point of lower than that of the decomposition temperature of the radioactive wastes. Further, the radioactive wastes having a possibility of evaporation and scattering along with oxidation can be solidified in a stable form by putting the solidification system under an inert gas atmosphere. Then in the present invention, a metal is selected as a solidification material for radioactive wastes, and a metal, for example, lead or tin having a melting point of lower than that of the decomposition temperature of the wastes is used in order to prevent the release of the wastes during the solidification operation. Radioactive wastes which are unstable in air and scatter easily, for example, Ru or the like can be converted into a stable solidification product by conducting the solidification processing under an inert gas atmosphere. (T.M.).

Simulating the Effect of Space Vehicle Environments on Directional Solidification of a Binary Alloy

Science.gov (United States)

Westra, D. G.; Heinrich, J. C.; Poirier, D. R.

2003-01-01

Space microgravity missions are designed to provide a microgravity environment for scientific experiments, but these missions cannot provide a perfect environment, due to vibrations caused by crew activity, on-board experiments, support systems (pumps, fans, etc.), periodic orbital maneuvers, and water dumps. Therefore, it is necessary to predict the impact of these vibrations on space experiments, prior to performing them. Simulations were conducted to study the effect of the vibrations on the directional solidification of a dendritic alloy. Finite element ca!cu!attie?ls were dme with a simd2titcr based on a continuum model of dendritic solidification, using the Fractional Step Method (FSM). The FSM splits the solution of the momentum equation into two steps: the viscous intermediate step, which does not enforce continuity; and the inviscid projection step, which calculates the pressure and enforces continuity. The FSM provides significant computational benefits for predicting flows in a directionally solidified alloy, compared to other methods presently employed, because of the efficiency gains in the uncoupled solution of velocity and pressure. finite differences, arises when the interdendritic liquid reaches the eutectic temperature and concentration. When a node reaches eutectic temperature, it is assumed that the solidification of the eutectic liquid continues at constant temperature until all the eutectic is solidified. With this approach, solidification is not achieved continuously across an element; rather, the element is not considered solidified until the eutectic isotherm overtakes the top nodes. For microgravity simulations, where the convection is driven by shrinkage, it introduces large variations in the fluid velocity. When the eutectic isotherm reaches a node, all the eutectic must be solidified in a short period, causing an abrupt increase in velocity. To overcome this difficulty, we employed a scheme to numerically predict a more accurate value

Solidification microstructure development

Indian Academy of Sciences (India)

Unknown

A majority of manufacturing processes involve melting and solidification of metals and ... In such a case (for example, chill casting), the solidification thickness (S) is ... (5). Here, LX is the system length scale in one dimension and DS is the solute diffusivity in solid. Thermal and solutal diffusivities are finite and usually very ...

Plastic solidification of radioactive wastes

International Nuclear Information System (INIS)

Moriyama, Noboru

1981-01-01

Over 20 years have elapsed after the start of nuclear power development, and the nuclear power generation in Japan now exceeds the level of 10,000 MW. In order to meet the energy demands, the problem of the treatment and disposal of radioactive wastes produced in nuclear power stations must be solved. The purpose of the plastic solidification of such wastes is to immobilize the contained radionuclides, same as other solidification methods, to provide the first barrier against their move into the environment. The following matters are described: the nuclear power generation in Japan, the radioactive wastes from LWR plants, the position of plastic solidification, the status of plastic solidification in overseas countries and in Japan, the solidification process for radioactive wastes with polyethylene, and the properties of solidified products, and the leachability of radionuclides in asphalt solids. (J.P.N.)

Negative Ion Density Fronts

International Nuclear Information System (INIS)

Igor Kaganovich

2000-01-01

Negative ions tend to stratify in electronegative plasmas with hot electrons (electron temperature Te much larger than ion temperature Ti, Te > Ti ). The boundary separating a plasma containing negative ions, and a plasma, without negative ions, is usually thin, so that the negative ion density falls rapidly to zero-forming a negative ion density front. We review theoretical, experimental and numerical results giving the spatio-temporal evolution of negative ion density fronts during plasma ignition, the steady state, and extinction (afterglow). During plasma ignition, negative ion fronts are the result of the break of smooth plasma density profiles during nonlinear convection. In a steady-state plasma, the fronts are boundary layers with steepening of ion density profiles due to nonlinear convection also. But during plasma extinction, the ion fronts are of a completely different nature. Negative ions diffuse freely in the plasma core (no convection), whereas the negative ion front propagates towards the chamber walls with a nearly constant velocity. The concept of fronts turns out to be very effective in analysis of plasma density profile evolution in strongly non-isothermal plasmas

Analysis and calculation of macrosegregation in a casting ingot. MPS solidification model. Volume 1: Formulation and analysis

Science.gov (United States)

Maples, A. L.; Poirier, D. R.

1980-01-01

The physical and numerical formulation of a model for the horizontal solidification of a binary alloy is described. It can be applied in an ingot. The major purpose of the model is to calculate macrosegregation in a casting ingot which results from flow of interdendritic liquid during solidification. The flow, driven by solidification contractions and by gravity acting on density gradients in the interdendritic liquid, was modeled as flow through a porous medium. The symbols used are defined. The physical formulation of the problem leading to a set of equations which can be used to obtain: (1) the pressure field; (2) the velocity field: (3) mass flow and (4) solute flow in the solid plus liquid zone during solidification is presented. With these established, the model calculates macrosegregation after solidification is complete. The numerical techniques used to obtain solution on a computational grid are presented. Results, evaluation of the results, and recommendations for future development of the model are given. The macrosegregation and flow field predictions for tin-lead, aluminum-copper, and tin-bismuth alloys are included as well as comparisons of some of the predictions with published predictions or with empirical data.

Beam front accelerators

International Nuclear Information System (INIS)

Reiser, M.

1982-01-01

An intense relativistic electron beam cannot propagate in a metal drift tube when the current exceeds the space charge limit. Very high charge density and electric field gradients (10 2 to 10 3 MV/m) develop at the beam front and the electrons are reflected. When a neutral gas or a plasma is present, collective acceleration of positive ions occur, and the resulting charge neutralization enables the beam to propagate. Experimental results, theoretical understanding, and schemes to achieve high ion energies by external control of the beam front velocity will be reviewed

Advances in Solidification Processing

Directory of Open Access Journals (Sweden)

Hugo F. Lopez

2015-08-01

Full Text Available Melt solidification is the shortest and most viable route to obtain components, starting from the design to the finished products. Hence, a sound knowledge of the solidification of metallic materials is essential for the development of advanced structural metallic components that drive modern technological societies. As a result, there have been innumerable efforts and full conferences dedicated to this important subject [1–6]. In addition, there are various scientific journals fully devoted to investigating the various aspects which give rise to various solidification microstructures [7–9]. [...

Solidification Sequence of Spray-Formed Steels

Science.gov (United States)

Zepon, Guilherme; Ellendt, Nils; Uhlenwinkel, Volker; Bolfarini, Claudemiro

2016-02-01

Solidification in spray-forming is still an open discussion in the atomization and deposition area. This paper proposes a solidification model based on the equilibrium solidification path of alloys. The main assumptions of the model are that the deposition zone temperature must be above the alloy's solidus temperature and that the equilibrium liquid fraction at this temperature is reached, which involves partial remelting and/or redissolution of completely solidified droplets. When the deposition zone is cooled, solidification of the remaining liquid takes place under near equilibrium conditions. Scanning electron microscopy (SEM) and optical microscopy (OM) were used to analyze the microstructures of two different spray-formed steel grades: (1) boron modified supermartensitic stainless steel (SMSS) and (2) D2 tool steel. The microstructures were analyzed to determine the sequence of phase formation during solidification. In both cases, the solidification model proposed was validated.

Front tracking based modeling of the solid grain growth on the adaptive control volume grid

Science.gov (United States)

Seredyński, Mirosław; Łapka, Piotr

2017-07-01

The paper presents the micro-scale model of unconstrained solidification of the grain immersed in under-cooled liquid, based on the front tracking approach. For this length scale, the interface tracked through the domain is meant as the solid-liquid boundary. To prevent generation of huge meshes the energy transport equation is discretized on the adaptive control volume (c.v.) mesh. The coupling of dynamically changing mesh and moving front position is addressed. Preliminary results of simulation of a test case, the growth of single grain, are presented and discussed.

Modeling of columnar and equiaxed solidification of binary mixtures; Modelisation de la solidification colonnaire et equiaxe de melanges binaires

Energy Technology Data Exchange (ETDEWEB)

Roux, P

2005-12-15

This work deals with the modelling of dendritic solidification in binary mixtures. Large scale phenomena are represented by volume averaging of the local conservation equations. This method allows to rigorously derive the partial differential equations of averaged fields and the closure problems associated to the deviations. Such problems can be resolved numerically on periodic cells, representative of dendritic structures, in order to give a precise evaluation of macroscopic transfer coefficients (Drag coefficients, exchange coefficients, diffusion-dispersion tensors...). The method had already been applied for a model of columnar dendritic mushy zone and it is extended to the case of equiaxed dendritic solidification, where solid grains can move. The two-phase flow is modelled with an Eulerian-Eulerian approach and the novelty is to account for the dispersion of solid velocity through the kinetic agitation of the particles. A coupling of the two models is proposed thanks to an original adaptation of the columnar model, allowing for undercooling calculation: a solid-liquid interfacial area density is introduced and calculated. At last, direct numerical simulations of crystal growth are proposed with a diffuse interface method for a representation of local phenomena. (author)

Solidification and casting

CERN Document Server

Cantor, Brian

2002-01-01

INDUSTRIAL PERSPECTIVEDirect chillcasting of aluminium alloysContinuous casting of aluminium alloysContinuous casting of steelsCastings in the automotive industryCast aluminium-silicon piston alloysMODELLING AND SIMULATIONModelling direct chill castingMold filling simulation of die castingThe ten casting rulesGrain selection in single crystal superalloy castingsDefects in aluminium shape castingPattern formation during solidificationPeritectic solidificationSTRUCTURE AND DEFECTSHetergeneous nucleation in aluminium alloysCo

Front propagation in flipping processes

International Nuclear Information System (INIS)

Antal, T; Ben-Avraham, D; Ben-Naim, E; Krapivsky, P L

2008-01-01

We study a directed flipping process that underlies the performance of the random edge simplex algorithm. In this stochastic process, which takes place on a one-dimensional lattice whose sites may be either occupied or vacant, occupied sites become vacant at a constant rate and simultaneously cause all sites to the right to change their state. This random process exhibits rich phenomenology. First, there is a front, defined by the position of the leftmost occupied site, that propagates at a nontrivial velocity. Second, the front involves a depletion zone with an excess of vacant sites. The total excess Δ k increases logarithmically, Δ k ≅ ln k, with the distance k from the front. Third, the front exhibits ageing-young fronts are vigorous but old fronts are sluggish. We investigate these phenomena using a quasi-static approximation, direct solutions of small systems and numerical simulations

Solidification paths of multicomponent monotectic aluminum alloys

Energy Technology Data Exchange (ETDEWEB)

Mirkovic, Djordje; Groebner, Joachim [Clausthal University of Technology, Institute of Metallurgy, Robert-Koch-Street 42, D-38678 Clausthal-Zellerfeld (Germany); Schmid-Fetzer, Rainer [Clausthal University of Technology, Institute of Metallurgy, Robert-Koch-Street 42, D-38678 Clausthal-Zellerfeld (Germany)], E-mail: schmid-fetzer@tu-clausthal.de

2008-10-15

Solidification paths of three ternary monotectic alloy systems, Al-Bi-Zn, Al-Sn-Cu and Al-Bi-Cu, are studied using thermodynamic calculations, both for the pertinent phase diagrams and also for specific details concerning the solidification of selected alloy compositions. The coupled composition variation in two different liquids is quantitatively given. Various ternary monotectic four-phase reactions are encountered during solidification, as opposed to the simple binary monotectic, L' {yields} L'' + solid. These intricacies are reflected in the solidification microstructures, as demonstrated for these three aluminum alloy systems, selected in view of their distinctive features. This examination of solidification paths and microstructure formation may be relevant for advanced solidification processing of multicomponent monotectic alloys.

Simulating the Evolving Behavior of Secondary Slow Slip Fronts

Science.gov (United States)

Peng, Y.; Rubin, A. M.

2017-12-01

High-resolution tremor catalogs of slow slip events reveal secondary slow slip fronts behind the main front that repetitively occupy the same source area during a single episode. These repetitive fronts are most often observed in regions with high tremor density. Their recurrence intervals gradually increase from being too short to be tidally modulated (tens of minutes) to being close to tidal periods (about 12 or 24 hours). This could be explained by a decreasing loading rate from creep in the surrounding regions (with few or no observable tremor events) as the main front passes by. As the recurrence intervals of the fronts increase, eventually they lock in on the tidal periods. We attempt to simulate this numerically using a rate-and-state friction law that transitions from velocity-weakening at low slip speeds to velocity strengthening at high slip speeds. Many small circular patches with a cutoff velocity an order of magnitude higher than that of the background are randomly placed on the fault, in order to simulate the average properties of the high-density tremor zone. Preliminary results show that given reasonable parameters, this model produces similar propagation speeds of the forward-migrating main front inside and outside the high-density tremor zone, consistent with observations. We will explore the behavior of the secondary fronts that arise in this model, in relation to the local density of the small tremor-analog patches, the overall geometry of the tremor zone and the tides.

Fundamental Metallurgy of Solidification

DEFF Research Database (Denmark)

Tiedje, Niels

2004-01-01

The text takes the reader through some fundamental aspects of solidification, with focus on understanding the basic physics that govern solidification in casting and welding. It is described how the first solid is formed and which factors affect nucleation. It is described how crystals grow from...

Characteristics of Cement Solidification of Metal Hydroxide Waste

Directory of Open Access Journals (Sweden)

Dae-Seo Koo

2017-02-01

Full Text Available To perform the permanent disposal of metal hydroxide waste from electro-kinetic decontamination, it is necessary to secure the technology for its solidification. The integrity tests on the fabricated solidification should also meet the criteria of the Korea Radioactive Waste Agency. We carried out the solidification of metal hydroxide waste using cement solidification. The integrity tests such as the compressive strength, immersion, leach, and irradiation tests on the fabricated cement solidifications were performed. It was also confirmed that these requirements of the criteria of Korea Radioactive Waste Agency on these cement solidifications were met. The microstructures of all the cement solidifications were analyzed and discussed.

Characteristics of cement solidification of metal hydroxide waste

Energy Technology Data Exchange (ETDEWEB)

Koo, Dae Seo; Sung, Hyun Hee; Kim, Seung Soo; Kim, Gye Nam; Choi, Jong Won [Dept. of Decontemination Decommission Technology Development, Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2017-02-15

To perform the permanent disposal of metal hydroxide waste from electro-kinetic decontamination, it is necessary to secure the technology for its solidification. The integrity tests on the fabricated solidification should also meet the criteria of the Korea Radioactive Waste Agency. We carried out the solidification of metal hydroxide waste using cement solidification. The integrity tests such as the compressive strength, immersion, leach, and irradiation tests on the fabricated cement solidifications were performed. It was also confirmed that these requirements of the criteria of Korea Radioactive Waste Agency on these cement solidifications were met. The microstructures of all the cement solidifications were analyzed and discussed.

Self-Propagating Reactive Fronts in Compacts of Multilayered Particles

International Nuclear Information System (INIS)

Sraj, I.; Vohra, M.; Alawieh, L.; Weihs, T.P.; Knio, O.M.

2013-01-01

Reactive multilayered foils in the form of thin films have gained interest in various applications such as joining, welding, and ignition. Typically, thin film multilayers support self-propagating reaction fronts with speeds ranging from 1 to 20 m/s. In some applications, however, reaction fronts with much smaller velocities are required. This recently motivated Fritz et al. (2011) to fabricate compacts of regular sized/shaped multilayered particles and demonstrate self-sustained reaction fronts having much smaller velocities than thin films with similar layering. In this work, we develop a simplified numerical model to simulate the self-propagation of reactive fronts in an idealized compact, comprising identical Ni/Al multilayered particles in thermal contact. The evolution of the reaction in the compact is simulated using a two-dimensional transient model, based on a reduced description of mixing, heat release, and thermal transport. Computed results reveal that an advancing reaction front can be substantially delayed as it crosses from one particle to a neighboring particle, which results in a reduced mean propagation velocity. A quantitative analysis is thus conducted on the dependence of these phenomena on the contact area between the particles, the thermal contact resistance, and the arrangement of the multilayered particles.

Self-Propagating Reactive Fronts in Compacts of Multilayered Particles

Directory of Open Access Journals (Sweden)

Ihab Sraj

2013-01-01

Full Text Available Reactive multilayered foils in the form of thin films have gained interest in various applications such as joining, welding, and ignition. Typically, thin film multilayers support self-propagating reaction fronts with speeds ranging from 1 to 20 m/s. In some applications, however, reaction fronts with much smaller velocities are required. This recently motivated Fritz et al. (2011 to fabricate compacts of regular sized/shaped multilayered particles and demonstrate self-sustained reaction fronts having much smaller velocities than thin films with similar layering. In this work, we develop a simplified numerical model to simulate the self-propagation of reactive fronts in an idealized compact, comprising identical Ni/Al multilayered particles in thermal contact. The evolution of the reaction in the compact is simulated using a two-dimensional transient model, based on a reduced description of mixing, heat release, and thermal transport. Computed results reveal that an advancing reaction front can be substantially delayed as it crosses from one particle to a neighboring particle, which results in a reduced mean propagation velocity. A quantitative analysis is thus conducted on the dependence of these phenomena on the contact area between the particles, the thermal contact resistance, and the arrangement of the multilayered particles.

Friction forces on phase transition fronts

International Nuclear Information System (INIS)

Mégevand, Ariel

2013-01-01

In cosmological first-order phase transitions, the microscopic interaction of the phase transition fronts with non-equilibrium plasma particles manifests itself macroscopically as friction forces. In general, it is a nontrivial problem to compute these forces, and only two limits have been studied, namely, that of very slow walls and, more recently, ultra-relativistic walls which run away. In this paper we consider ultra-relativistic velocities and show that stationary solutions still exist when the parameters allow the existence of runaway walls. Hence, we discuss the necessary and sufficient conditions for the fronts to actually run away. We also propose a phenomenological model for the friction, which interpolates between the non-relativistic and ultra-relativistic values. Thus, the friction depends on two friction coefficients which can be calculated for specific models. We then study the velocity of phase transition fronts as a function of the friction parameters, the thermodynamic parameters, and the amount of supercooling

PIV tracer behavior on propagating shock fronts

International Nuclear Information System (INIS)

Glazyrin, Fyodor N; Mursenkova, Irina V; Znamenskaya, Irina A

2016-01-01

The present work was aimed at the quantitative particle image velocimetry (PIV) measurement of a velocity field near the front of a propagating shock wave and the study of the dynamics of liquid tracers crossing the shock front. For this goal, a shock tube with a rectangular cross-section (48  ×  24 mm) was used. The flat shock wave with Mach numbers M  =  1.4–2.0 propagating inside the tube channel was studied as well as an expanding shock wave propagating outside the channel with M  =  1.2–1.8 at its main axis. The PIV imaging of the shock fronts was carried out with an aerosol of dioctyl sebacate (DEHS) as tracer particles. The pressures of the gas in front of the shock waves studied ranged from 0.013 Mpa to 0.1 MPa in the series of experiments. The processed PIV data, compared to the 1D normal shock theory, yielded consistent values of wake velocity immediately behind the plain shock wave. Special attention was paid to the blurring of the velocity jump on the shock front due to the inertial particle lag and peculiarities of the PIV technique. A numerical algorithm was developed for analysis and correction of the PIV data on the shock fronts, based on equations of particle-flow interaction. By application of this algorithm, the effective particle diameter of the DEHS aerosol tracers was estimated as 1.03  ±  0.12 μm. A number of different formulations for particle drag were tested with this algorithm, with varying success. The results show consistency with previously reported experimental data obtained for cases of stationary shock waves. (paper)

Optimisation of the microstructure of YBa2Cu3O7-δ superconducting ceramics textured by horizontal solidification. Effects of a magnetic field applied vertically during the solidification process

International Nuclear Information System (INIS)

Durand, L.

1995-01-01

We have shown that il was possible to disperse in a very homogeneous way, into the 123 matrix, 211 particles regular in size around 1μm, by directional solidification of a mixture of 123 plus 211 sol-gel powders. The addition of 0.5 wt% of Pt lo this precursor mixture has permitted us to refine further the size of the 211 particles. Moreover, we have established that the finer the 123 powder and the faster the heating rate, the smaller the 211 particles. From another hand, we have found that the size and the microstructure of the solidified single domain was dependant upon numerous parameters. In particular, we have noted that if the cold pressed green body was not sintered before being melted, grains of solid CuO appeared into the liquid which next hardly recombined with it, giving rise to a comb like solidification front, witness of a local un-stability. Moreover, in these particular conditions, the 123 formed was found to be understoichiometric in Cu and the single domains severely limited in extension. Finally, we have observed that the application of a 4 T magnetic field during the solidification of a bar the longest axis of which was horizontal tended to align the c axis of the 123 grains parallel to the field. Incidentally, we have discovered that in the same conditions, the 211 particles trapped into the 123 matrix were also preferentially oriented. (author)

Probing liquation cracking and solidification through modeling of momentum, heat, and solute transport during welding of aluminum alloys

International Nuclear Information System (INIS)

Mishra, S.; Chakraborty, S.; DebRoy, T.

2005-01-01

A transport phenomena-based mathematical model is developed to understand liquation cracking in weldments during fusion welding. Equations of conservation of mass, momentum, heat, and solute transport are numerically solved considering nonequilibrium solidification and filler metal addition to determine the solid and liquid phase fractions in the solidifying region and the solute distribution in the weld pool. An effective partition coefficient that considers the local interface velocity and the undercooling is used to simulate solidification during welding. The calculations show that convection plays a dominant role in the solute transport inside the weld pool. The predicted weld-metal solute content agreed well with the independent experimental observations. The liquation cracking susceptibility in Al-Cu alloy weldments could be reliably predicted by the model based on the computed solidifying weld-metal composition and solid fraction considering nonequilibrium solidification

Radioactive waste solidification material

International Nuclear Information System (INIS)

Nishihara, Yukio; Wakuta, Kuniharu; Ishizaki, Kanjiro; Koyanagi, Naoaki; Sakamoto, Hiroyuki; Uchida, Ikuo.

1992-01-01

The present invention concerns a radioactive waste solidification material containing vermiculite cement used for a vacuum packing type waste processing device, which contains no residue of calcium hydroxide in cement solidification products. No residue of calcium hydroxide means, for example, that peak of Ca(OH) 2 is not recognized in an X ray diffraction device. With such procedures, since calcium sulfoaluminate clinker and Portland cement themselves exhibit water hardening property, and slugs exhibit hydration activity from the early stage, the cement exhibits quick-hardening property, has great extension of long term strength, further, has no shrinking property, less dry- shrinkage, excellent durability, less causing damages such as cracks and peeling as processing products of radioactive wastes, enabling to attain highly safe solidification product. (T.M.)

Propagative selection of tilted array patterns in directional solidification

Science.gov (United States)

Song, Younggil; Akamatsu, Silvère; Bottin-Rousseau, Sabine; Karma, Alain

2018-05-01

We investigate the dynamics of tilted cellular/dendritic array patterns that form during directional solidification of a binary alloy when a preferred-growth crystal axis is misoriented with respect to the temperature gradient. In situ experimental observations and phase-field simulations in thin samples reveal the existence of a propagative source-sink mechanism of array spacing selection that operates on larger space and time scales than the competitive growth at play during the initial solidification transient. For tilted arrays, tertiary branching at the diverging edge of the sample acts as a source of new cells with a spacing that can be significantly larger than the initial average spacing. A spatial domain of large spacing then invades the sample propagatively. It thus yields a uniform spacing everywhere, selected independently of the initial conditions, except in a small region near the converging edge of the sample, which acts as a sink of cells. We propose a discrete geometrical model that describes the large-scale evolution of the spatial spacing profile based on the local dependence of the cell drift velocity on the spacing. We also derive a nonlinear advection equation that predicts the invasion velocity of the large-spacing domain, and sheds light on the fundamental nature of this process. The models also account for more complex spacing modulations produced by an irregular dynamics at the source, in good quantitative agreement with both phase-field simulations and experiments. This basic knowledge provides a theoretical basis to improve the processing of single crystals or textured polycrystals for advanced materials.

Method of plastic solidification of radioactive wastes

International Nuclear Information System (INIS)

Oikawa, Yasuo; Tokimitsu, Fujio.

1986-01-01

Purpose: To prevent occurrence of deleterious cracks to the inside and the surface of solidification products, as well as eliminate gaps between the products and the vessel inner wall upon plastic solidification processing for powdery or granular radioactive wastes. Method: An appropriate amount of thermoplastic resins such as styrenic polymer or vinyl acetate type polymer as a low shrinking agent is added and mixed with unsaturated polyester resins to be mixed with radioactive wastes so as to reduce the shrinkage-ratio to 0 % upon curing reaction. Thus, a great shrinkage upon hardening the mixture is suppressed to prevent the occurrence of cracks to the surface and the inside of the solidification products, as well as prevent the gaps between the inner walls of a drum can vessel and the products upon forming solidification products to the inside of the drum can. The resultant solidification products have a large compression strength and can sufficiently satisfy the evaluation standards as the plastic solidification products of radioactive wastes. (Horiuchi, T.)

The influence of buoyant forces and volume fraction of particles on the particle pushing/entrapment transition during directional solidification of Al/SiC and Al/graphite composites

Science.gov (United States)

Stefanescu, Doru M.; Moitra, Avijit; Kacar, A. Sedat; Dhindaw, Brij K.

1990-01-01

Directional solidification experiments in a Bridgman-type furnace were used to study particle behavior at the liquid/solid interface in aluminum metal matrix composites. Graphite or siliconcarbide particles were first dispersed in aluminum-base alloys via a mechanically stirred vortex. Then, 100-mm-diameter and 120-mm-long samples were cast in steel dies and used for directional solidification. The processing variables controlled were the direction and velocity of solidification and the temperature gradient at the interface. The material variables monitored were the interface energy, the liquid/particle density difference, the particle/liquid thermal conductivity ratio, and the volume fraction of particles. These properties were changed by selecting combinations of particles (graphite or silicon carbide) and alloys (Al-Cu, Al-Mg, Al-Ni). A model which considers process thermodynamics, process kinetics (including the role of buoyant forces), and thermophysical properties was developed. Based on solidification direction and velocity, and on materials properties, four types of behavior were predicted. Sessile drop experiments were also used to determine some of the interface energies required in calculation with the proposed model. Experimental results compared favorably with model predictions.

Method of storing solidification products

International Nuclear Information System (INIS)

Tani, Yutaro.

1985-01-01

Purpose: To enable to efficiently and satisfactorily cool and store solidification products of liquid wastes generated from the reactor spent fuel reprocessing process by a simple facility. Method: Liquid wastes generated from the reactor spent fuel reprocessing process are caused to flow from the upper opening to the inside of a spherical canistor. The opening of the spherical canistor is welded with a lid by a remote control and the liquid wastes are tightly sealed within the spherical canistor as glass solidification products. Spherical canistors having the solidification products tightly sealed therein are sent into and stored in a hopper by the remote control. Further, a blower is driven upon storing to suck cooling air from the cooling air intake port to the inside of the hopper to absorb the decay heat of radioactive materials in the solidification products and the air is discharged from the duct and through the stack to the atmosphere. (Kawakami, Y.)

Tidal variations of flow convergence, shear, and stratification at the Rio de la Plata estuary turbidity front

Science.gov (United States)

FramiñAn, Mariana B.; Valle-Levinson, Arnoldo; Sepúlveda, HéCtor H.; Brown, Otis B.

2008-08-01

Intratidal variability of density and velocity fields is investigated at the turbidity front of the Río de la Plata Estuary, South America. Current velocity and temperature-salinity profiles collected in August 1999 along a repeated transect crossing the front are analyzed. Horizontal and vertical gradients, stability of the front, convergence zones, and transverse flow associated to the frontal boundary are described. Strong horizontal convergence of the across-front velocity and build up of along-front velocity shear were observed at the front. In the proximity of the front, enhanced transverse (or along-front) flow created jet-like structures at the surface and near the bottom flowing in opposite directions. These structures persisted throughout the tidal cycle and were advected upstream (downstream) by the flood (ebb) current through a distance of ˜10 km. During peak flood, the upper layer flow reversed from its predominant downstream direction and upstreamflow occupied the entire water column; outside the peak flood, two-layer estuarine circulation dominated. Changes in density field were observed in response to tidal straining, tidal advection, and wind-induced mixing, but stratification remained throughout the tidal cycle. This work demonstrates the large spatial variability of the velocity field at the turbidity front; it provides evidence of enhanced transverse circulation along the frontal boundary; and reveals the importance of advective and frictional intratidal processes in the dynamics of the central part of the estuary.

Method of processing solidification product of radioactive waste

International Nuclear Information System (INIS)

Daime, Fumiyoshi.

1988-01-01

Purpose: To improve the long-time stability of solidification products by providing solidification products with liquid tightness, gas tightness, abrasion resistance, etc., of the products in the course of the solidification for the treatment of radioactive wastes. Method: The surface of solidification products prepared by mixing solidifying agents with powder or pellets is entirely covered with high molecular polymer such as epoxy resin. The epoxy resin has excellent properties such as radiation-resistance, heat resistance, water proofness and chemical resistance, as well as have satisfactory mechanical properties. This can completely isolate the solidification products of radioactive wastes from the surrounding atmosphere. (Yoshino, Y.)

Solidification process for toxic and hazardous wastes. Second part: Cement solidification matrices

International Nuclear Information System (INIS)

Donato, A.; Arcuri, L.; Dotti, M.; Pace, A.; Pietrelli, L.; Ricci, G.; Basta, M.; Cali, V.; Pagliai, V.

1989-05-01

This paper reports the second part of a general study carried out at the Nuclear Fuel Division aiming at verifying the possible application of the radioactive waste solidification processes to industrial hazardous wastes (RTN). The cement solidification of several RTN types has been taken into consideration, both from the technical and from the economic point of view. After a short examination of the Italian juridical and economical situation in the field, which demonstrates the need of the RTN solidification, the origin and characteristics of the RTN considered in the study and directly provided by the producing industries are reviewed. The laboratory experimental results of the cementation of RTN produced by gold manufacturing industries and by galvanic industries are reported. The cementation process can be considered a very effective mean for reducing both the RTN management costs and the environmental impact of RTN disposal. (author)

Search for a solute-drag effect in dendritic solidification

International Nuclear Information System (INIS)

Eckler, K.; Herlach, D.M.; Aziz, M.J.

1994-01-01

The authors report the results of an indirect experimental test for the solute-drag effect in alloy solidification by fitting the data of Eckler et.al. for Ni-B dendrite tip velocities vs undercooling to models in several ways. The unknown equilibrium partition coefficient, k e , was varied as a fitting parameter. When they combine the dendrite growth model of Boettinger et al. with the Continuous Growth Model (CGM) of Aziz and Kaplan with solute drag, they cannot fit the data for any value of k e . When they combine dendrite growth theory with the CGM without solute drag, they obtain a reasonable fit to the data for k e = 4 x 10 -6 . When they combine dendrite growth theory with a new partial-solute-drag interpolation between the with-solute-drag and the without-solute-drag versions of the CGM, they obtain a still better fit to the data for k e = 2.8 x 10 - 4. This result points out the possibility of partial solute-drag during solidification and the importance of an independent determination of k e in order to distinguish between models

Modeling of columnar and equiaxed solidification of binary mixtures

International Nuclear Information System (INIS)

Roux, P.

2005-12-01

This work deals with the modelling of dendritic solidification in binary mixtures. Large scale phenomena are represented by volume averaging of the local conservation equations. This method allows to rigorously derive the partial differential equations of averaged fields and the closure problems associated to the deviations. Such problems can be resolved numerically on periodic cells, representative of dendritic structures, in order to give a precise evaluation of macroscopic transfer coefficients (Drag coefficients, exchange coefficients, diffusion-dispersion tensors...). The method had already been applied for a model of columnar dendritic mushy zone and it is extended to the case of equiaxed dendritic solidification, where solid grains can move. The two-phase flow is modelled with an Eulerian-Eulerian approach and the novelty is to account for the dispersion of solid velocity through the kinetic agitation of the particles. A coupling of the two models is proposed thanks to an original adaptation of the columnar model, allowing for undercooling calculation: a solid-liquid interfacial area density is introduced and calculated. At last, direct numerical simulations of crystal growth are proposed with a diffuse interface method for a representation of local phenomena. (author)

High-velocity frictional properties of gabbro

Science.gov (United States)

Tsutsumi, Akito; Shimamoto, Toshihiko

High-velocity friction experiments have been performed on a pair of hollow-cylindrical specimens of gabbro initially at room temperature, at slip rates from 7.5 mm/s to 1.8 m/s, with total circumferential displacements of 125 to 174 m, and at normal stresses to 5 MPa, using a rotary-shear high-speed friction testing machine. Steady-state friction increases slightly with increasing slip rate at slip rates to about 100 mm/s (velocity strengthening) and it decreases markedly with increasing slip rate at higher velocities (velocity weakening). Steady-state friction in the velocity weakening regime is lower for the non-melting case than the frictional melting case, due perhaps to severe thermal fracturing. A very large peak friction is always recognized upon the initiation of visible frictional melting, presumably owing to the welding of fault surfaces upon the solidification of melt patches. Frictional properties thus change dramatically with increasing displacement at high velocities, and such a non-linear effect must be incorporated into the analysis of earthquake initiation processes.

Solidification and vitrification life-cycle economics study

International Nuclear Information System (INIS)

Gimpel, R.F.

1992-01-01

Solidification (making concrete) and vitrification (making glass) are frequently the treatment methods recommended for treating inorganic or radioactive wastes. Ex-situ solidification and vitrification are the competing methods for treating in excess of 450 000 cm 3 of low-level radioactive and mixed wastes at the Fernald Environmental Management Project (FEMP) located near Cincinnati, Ohio. This paper summarizes a detailed study done to: (1) compare the economics of the solidification and vitrification processes, (2) determine if the stigma assigned to vitrification is warranted and, (3) determine if investing millions of dollars into vitrification development, along with solidification development, at Fernald is warranted

Front propagation in a regular vortex lattice: Dependence on the vortex structure.

Science.gov (United States)

Beauvier, E; Bodea, S; Pocheau, A

2017-11-01

We investigate the dependence on the vortex structure of the propagation of fronts in stirred flows. For this, we consider a regular set of vortices whose structure is changed by varying both their boundary conditions and their aspect ratios. These configurations are investigated experimentally in autocatalytic solutions stirred by electroconvective flows and numerically from kinematic simulations based on the determination of the dominant Fourier mode of the vortex stream function in each of them. For free lateral boundary conditions, i.e., in an extended vortex lattice, it is found that both the flow structure and the front propagation negligibly depend on vortex aspect ratios. For rigid lateral boundary conditions, i.e., in a vortex chain, vortices involve a slight dependence on their aspect ratios which surprisingly yields a noticeable decrease of the enhancement of front velocity by flow advection. These different behaviors reveal a sensitivity of the mean front velocity on the flow subscales. It emphasizes the intrinsic multiscale nature of front propagation in stirred flows and the need to take into account not only the intensity of vortex flows but also their inner structure to determine front propagation at a large scale. Differences between experiments and simulations suggest the occurrence of secondary flows in vortex chains at large velocity and large aspect ratios.

Critical Role of Crystalline Anisotropy in the Stability of Cellular Array Structures in Directional Solidification

International Nuclear Information System (INIS)

Kopczynski, P.; Rappel, W.; Karma, A.

1996-01-01

We calculate numerically the full Floquet-Bloch stability spectrum of cellular array structures in a symmetric model of directional solidification. Our results demonstrate that crystalline anisotropy critically influences the stability of these structures. Without anisotropy, the stability balloon of cells in the plane of wave number and velocity closes near the onset of morphological instability. With a finite, but even small, amount of anisotropy this balloon remains open and a band of stable solutions persists for higher velocities into a deep cell regime. The width of the balloon depends critically on the anisotropy strength. copyright 1996 The American Physical Society

Melting and solidification characteristics of a mixture of two types of latent heat storage material in a vessel

Science.gov (United States)

Yu, JikSu; Horibe, Akihiko; Haruki, Naoto; Machida, Akito; Kato, Masashi

2016-11-01

In this study, we investigated the fundamental melting and solidification characteristics of mannitol, erythritol, and their mixture (70 % by mass mannitol: 30 % by mass erythritol) as potential phase-change materials (PCMs) for latent heat thermal energy storage systems, specifically those pertaining to industrial waste heat, having temperatures in the range of 100-250 °C. The melting point of erythritol and mannitol, the melting peak temperature of their mixture, and latent heat were measured using differential scanning calorimetry. The thermal performance of the mannitol mixture was determined during melting and solidification processes, using a heat storage vessel with a pipe heat exchanger. Our results indicated phase-change (fusion) temperatures of 160 °C for mannitol and 113 and 150 °C for the mannitol mixture. Nondimensional correlation equations of the average heat transfer during the solidification process, as well as the temperature and velocity efficiencies of flowing silicon oil in the pipe and the phase-change material (PCM), were derived using several nondimensional parameters.

Solidification and vitrification life-cycle economics study

International Nuclear Information System (INIS)

Gimpel, R.F.

1992-01-01

Solidification (making concrete) and vitrification (making glass) are frequently the treatment methods recommended for treating inorganic or radioactive wastes. Solidification is generally perceived as the most economical treatment method, whereas vitrification is considered (by many) as the most effective of all treatment methods. Unfortunately, vitrification has acquired the stigma that it is too expensive to receive further consideration as an alternative to solidification in high volume treatment applications. Ex situ solidification and vitrification are the competing methods for treating in excess of 450,000 m 3 of low-level radioactive and mixed waste at the Fernald Environmental Management Project (FEMP or simply, Fernald) located near Cincinnati, Ohio. This paper s a detailed study done to: compare the economics of the solidification and vitrification processes; determine if the stigma assigned to vitrification is warranted; determine if investing millions of dollars into vitrification development, along with solidification development, at Fernald is warranted. Common parameters were determined and detailed life-cycle cost estimates were made. Incorporating the unit costs into a computer spreadsheet allowed 'what if' scenarios to be performed. Some scenarios investigated included variation of: remediation times, amount of wastes treated, treatment efficiencies, electrical and material costs and escalation

Progress on Numerical Modeling of the Dispersion of Ceramic Nanoparticles During Ultrasonic Processing and Solidification of Al-Based Nanocomposites

Science.gov (United States)

Zhang, Daojie; Nastac, Laurentiu

2016-12-01

In present study, 6061- and A356-based nano-composites are fabricated by using the ultrasonic stirring technology (UST) in a coreless induction furnace. SiC nanoparticles are used as the reinforcement. Nanoparticles are added into the molten metal and then dispersed by ultrasonic cavitation and acoustic streaming assisted by electromagnetic stirring. The applied UST parameters in the current experiments are used to validate a recently developed magneto-hydro-dynamics (MHD) model, which is capable of modeling the cavitation and nanoparticle dispersion during UST processing. The MHD model accounts for turbulent fluid flow, heat transfer and solidification, and electromagnetic field, as well as the complex interaction between the nanoparticles and both the molten and solidified alloys by using ANSYS Maxwell and ANSYS Fluent. Molecular dynamics (MD) simulations are conducted to analyze the complex interactions between the nanoparticle and the liquid/solid interface. The current modeling results demonstrate that a strong flow can disperse the nanoparticles relatively well during molten metal and solidification processes. MD simulation results prove that ultrafine particles (10 nm) will be engulfed by the solidification front instead of being pushed, which is beneficial for nano-dispersion.

Solidification process for sludge residue

International Nuclear Information System (INIS)

Pearce, K.L.

1998-01-01

This report investigates the solidification process used at 100-N Basin to solidify the N Basin sediment and assesses the N Basin process for application to the K Basin sludge residue material. This report also includes a discussion of a solidification process for stabilizing filters. The solidified matrix must be compatible with the Environmental Remediation Disposal Facility acceptance criteria

Phase-field simulation of peritectic solidification closely coupled with directional solidification experiments in an Al-36 wt% Ni alloy

International Nuclear Information System (INIS)

Siquieri, R; Emmerich, H; Doernberg, E; Schmid-Fetzer, R

2009-01-01

In this work we present experimental and theoretical investigations of the directional solidification of Al-36 wt% Ni alloy. A phase-field approach (Folch and Plapp 2005 Phys. Rev. E 72 011602) is coupled with the CALPHAD (calculation of phase diagrams) method to be able to simulate directional solidification of Al-Ni alloy including the peritectic phase Al 3 Ni. The model approach is calibrated by systematic comparison to microstructures grown under controlled conditions in directional solidification experiments. To illustrate the efficiency of the model it is employed to investigate the effect of temperature gradient on the microstructure evolution of Al-36 wt% Ni during solidification.

''New ' technology of solidification of liquid radioactive waste'

International Nuclear Information System (INIS)

Sytyl, V.A.; Svistova, L.M.; Spiridonova, V.P.

1998-01-01

It is generally accepted that the best method of processing of radioactive waste is its solidification and then storage. At present time, three methods of solidification of radioactive waste are widely used in the world: cementation, bituminous grouting and vitrification. But they do not solve the problem of ecologically processing of waste because of different disadvantages. General disadvantages are: low state of filling, difficulties in solidification of the crystalline hydrated forms of radioactive waste; particular sphere of application and economical difficulties while processing the great volume of waste. In connection with it the urgent necessity is emerging: to develop less expensive and ecologically more reliable technology of solidification of radioactive waste. A new method of solidification is presented with its technical schema. (N.C.)

Convection Effects During Bulk Transparent Alloy Solidification in DECLIC-DSI and Phase-Field Simulations in Diffusive Conditions

Science.gov (United States)

Mota, F. L.; Song, Y.; Pereda, J.; Billia, B.; Tourret, D.; Debierre, J.-M.; Trivedi, R.; Karma, A.; Bergeon, N.

2017-08-01

To study the dynamical formation and evolution of cellular and dendritic arrays under diffusive growth conditions, three-dimensional (3D) directional solidification experiments were conducted in microgravity on a model transparent alloy onboard the International Space Station using the Directional Solidification Insert in the DEvice for the study of Critical LIquids and Crystallization. Selected experiments were repeated on Earth under gravity-driven fluid flow to evidence convection effects. Both radial and axial macrosegregation resulting from convection are observed in ground experiments, and primary spacings measured on Earth and microgravity experiments are noticeably different. The microgravity experiments provide unique benchmark data for numerical simulations of spatially extended pattern formation under diffusive growth conditions. The results of 3D phase-field simulations highlight the importance of accurately modeling thermal conditions that strongly influence the front recoil of the interface and the selection of the primary spacing. The modeling predictions are in good quantitative agreements with the microgravity experiments.

Method of reprocessing radioactive asphalt solidification products

International Nuclear Information System (INIS)

Nakaya, Iwao; Murakami, Tadashi; Miyake, Takafumi; Inagaki, Yuzo.

1986-01-01

Purpose: To obtain heat-stable solidification products and decrease the total volume thereof by modifying the solidified form by the reprocessing of existent radioactive asphalt solidification products. Method: Radioactive asphalt solidification products are heated into a fluidized state. Then, incombustible solvents such as perchloroethylene or trichloroethylene are added to a dissolving tank to gradually dissolve the radioactive asphalt solidification products. Thus, organic materials such as asphalts are transferred into the solvent layer, while inorganic materials containing radioactive materials remain as they are in the separation tank. Then, the inorganic materials containing the radioactive materials are taken out and then solidified, for example, by converting them into a rock or glass form. (Kawakami, Y.)

XRMON-GF: A novel facility for solidification of metallic alloys with in situ and time-resolved X-ray radiographic characterization in microgravity conditions

Science.gov (United States)

Nguyen-Thi, H.; Reinhart, G.; Salloum Abou Jaoude, G.; Mathiesen, R. H.; Zimmermann, G.; Houltz, Y.; Voss, D.; Verga, A.; Browne, D. J.; Murphy, A. G.

2013-07-01

As most of the phenomena involved during the growth of metallic alloys from the melt are dynamic, in situ and time-resolved X-ray imaging should be retained as the method of choice for investigating the solidification front evolution. On Earth, the gravity force is the major source of various disturbing effects (natural convection, buoyancy/sedimentation, and hydrostatic pressure) which can significantly modify or mask certain physical mechanisms. Therefore solidification under microgravity is an efficient way to eliminate such perturbations to provide unique benchmark data for the validation of models and numerical simulations. Up to now, in situ observation during microgravity solidification experiments were limited to the investigations on transparent organic alloys, using optical methods. On the other hand, in situ observation on metallic alloys generally required synchrotron facilities. This paper reports on a novel facility we have designed and developed to investigate directional solidification on metallic alloys in microgravity conditions with in situ X-ray radiography observation. The facility consists of a Bridgman furnace and an X-ray radiography device specifically devoted to the study of Al-based alloys. An unprecedented experiment was recently performed on board a sounding rocket, with a 6 min period of microgravity. Radiographs were successfully recorded during the entire experiment including the melting and solidification phases of the sample, with a Field-of-View of about 5 mm×5 mm, a spatial resolution of about 4 µm and a frequency of 2 frames per second. Some preliminary results are presented on the solidification of the Al-20 wt% Cu sample, which validate the apparatus and confirm the potential of in situ X-ray characterization for the investigation of dynamical phenomena in materials processing, and particularly for the studying of metallic alloys solidification.

Solidification of Hypereutectic Thin Wall Ductile Cast Iron

DEFF Research Database (Denmark)

Pedersen, Karl Martin; Tiedje, Niels Skat

2006-01-01

solidification. The first stage, which was relatively short, had none or very little recalescence. Further under cooling, followed by reheating during recalescence, was necessary to initiate the second part of the eutectic solidification. Both the secondary under cooling and recalescence was larger in the 3 mm...... a higher Si content in the ferrite around the larger nodules compared to the ferrite around the rest of the nodules. This indicates that solidification took place along the following path: The solidification starts with nucleation and growth of primary graphite nodules. This probably starts during...

The effect of the melt spinning processing parameters on the solidification structures in Ti-30 at.% Ni-20 at.% Cu shape memory alloys

International Nuclear Information System (INIS)

Kim, Yeon-wook; Yun, Young-mok; Nam, Tae-hyun

2006-01-01

Solidification structures and shape memory characteristics of Ti-30 at.% Ni-20 at.% Cu alloy ribbons prepared by melt spinning were investigated by means of differential scanning calorimetry and X-ray diffraction. In these experiments particular attention has been paid to change the ejection temperature of the melt from 1350 to 1500 deg. C and the velocity of cooling wheel from 33 to 55 m/s. Then the cooling rates of ribbons were controlled. The effect of this cooling rate on solidification structures and martensitic transformation behaviors is discussed

Insights from field observations into controls on flow front speed in submarine sediment flows

Science.gov (United States)

Heerema, C.; Talling, P.; Cartigny, M.; Paull, C. K.; Gwiazda, R.; Clare, M. A.; Parsons, D. R.; Xu, J.; Simmons, S.; Maier, K. L.; Chapplow, N.; Gales, J. A.; McGann, M.; Barry, J.; Lundsten, E. M.; Anderson, K.; O'Reilly, T. C.; Rosenberger, K. J.; Sumner, E. J.; Stacey, C.

2017-12-01

Seafloor avalanches of sediment called turbidity currents are one of the most important processes for moving sediment across our planet. Only rivers carry comparable amounts of sediment across such large areas. Here we present some of the first detailed monitoring of these underwater flows that is being undertaken at a series of test sites. We seek to understand the factors that determine flow front speed, and how that speed varies with distance. This frontal speed is particularly important for predicting flow runout, and how the power of these hazardous flows varies with distance. First, we consider unusually detailed measurements of flow front speed defined by transit times between moorings and other tracked objects placed on the floor of Monterey Canyon offshore California in 2016-17. These measurements are then compared to flow front speeds measured using multiple moorings in Bute Inlet, British Columbia in 2016; and by cable breaks in Gaoping Canyon offshore Taiwan in 2006 and 2009. We seek to understand how flow front velocity is related to seafloor gradient, flow front thickness and density. It appears that the spatial evolution of frontal speed is similar in multiple flows, although their peak frontal velocities vary. Flow front velocity tends to increase rapidly initially before declining rather gradually over tens or even hundreds of kilometres. It has been proposed that submarine flows will exist in one of two states; either eroding and accelerating, or depositing sediment and dissipating. We conclude by discussing the implications of this global compilation of flow front velocities for understanding submarine flow behaviour.

Disorder trapping in Ni3(Al, Ti) by solidification from the undercooled melt

International Nuclear Information System (INIS)

Goetzinger, R.; Kurz, W.

1997-01-01

Modelling of rapid solidification predicts disorder trapping in the superlattice structure of Ni 3 Al. However, experimental investigations on this compound suffer from ambiguities concerning the solidification path. There is a phase selection competition between the ordered fcc γ'-phase (Ni 3 Al), the ordered bcc β-phase (NiAl), the disordered fcc γ-phase (Ni), the stable γ'/β eutectic and the metastable γ/β eutectic, and there are subsequent solid state transformations. A replacement of several at.% Al by Ti leads to a stabilization of the γ'-phase and to an avoidance of most of the problems encountered on Ni 3 Al. The experiments on Ni 3 (Al, Ti) presented here clearly show the expected disordered crystallization from the undercooled melt. This was proven by measuring the dendrite growth velocity of electromagnetically levitated droplets and by analysing the data in the framework of dendrite and kinetic growth models. Complementary microstructural investigations were performed on the as-solidified samples. (orig.)

Characteristic wave fronts in magnetohydrodynamics

International Nuclear Information System (INIS)

Menon, V.V.; Sharma, V.D.

1981-01-01

The influence of magnetic field on the process of steepening or flattening of the characteristic wave fronts in a plane and cylindrically symmetric motion of an ideal plasma is investigated. This aspect of the problem has not been considered until now. Remarkable differences between plane, cylindrical diverging, and cylindrical converging waves are discovered. The discontinuity in the velocity gradient at the wave front is shown to satisfy a Bernoulli-type equation. The discussion of the solutions of such equations reported in the literature is shown to be incomplete, and three general theorems are established. 18 refs

Low level waste solidification practice in Japan

International Nuclear Information System (INIS)

Sakata, S.; Kuribayashi, H.; Kono, Y.

1981-01-01

Both sea dumping and land isolation are planned to be accomplished for low level waste disposal in Japan. The conceptual design of land isolation facilities has been completed, and site selection will presently get underway. With respect to ocean dumping, safety surveys are being performed along the lines of the London Dumping Convention and the Revised Definitions and Recommendations of the IAEA, and the review of Japanese regulations and applicable criteria is being expedited. This paper discusses the present approach to waste solidification practices in Japan. It reports that the bitumen solidification process and the plastic solidification process are being increasingly used in Japan. Despite higher investment costs, both processes have advantages in operating cost, and are comparable to the cement solidification process in overall costs

Modification of doping front migration in electrochemical devices and application to organic electronics

International Nuclear Information System (INIS)

Nolte, Marius; Wan Xianglong; Kopp, Olga; Hermes, Ina; Panz, Jan; Rahmanian, Afsaneh; Knoll, Meinhard

2011-01-01

Research highlights: → In this paper we demonstrate several ways of tuning the doping front migration process in polymer electronic multilayer structures for the first time. By altering the migration layer thickness the migration velocity may be controlled and it is possible to switch between migration mechanisms. The mechanism of delamination produces rapid jumps in migration velocity, while the addition of 2-hydroxyethylcellulose (HEC) can inhibit this effect. In case of vapor activation the migration velocity may be influenced by the relative humidity or by varying the concentration of hygroscopic salts added to the migration layer. The migration mechanisms can be explained in terms of diffusion, capillary transport, and delamination. Tuning the migration process may be used to construct polymer electronic structures such as enhancement and depletion type pseudo transistors and electrical switches (ON-OFF and OFF-ON) with an improved switching time of several minutes. The doping front width is determined by microscopic optical absorption spectroscopy and can be controlled by the concentration of the doping solution. In case of low concentrations the electrochromic effect of the double front is observed. - Abstract: We demonstrate several methods of modifying the doping front migration process in multilayer structures, enabling control of migration velocity and switching between different migration mechanisms. Sharp jumps in migration velocity may be induced using a delamination effect. The influence of migration layer thickness and composition is examined. Migration velocity may also be influenced by exposing the system to a defined relative humidity or by varying the concentration of a hygroscopic salt in the migration layer. The migration mechanisms can be explained in terms of diffusion, capillary transport, and delamination. By tailoring the migration process a variety of polymer electronic structures such as pseudo transistors (enhancement and depletion

Relationships Between Solidification Parameters in A319 Aluminum Alloy

Science.gov (United States)

Vandersluis, E.; Ravindran, C.

2018-03-01

The design of high-performance materials depends on a comprehensive understanding of the alloy-specific relationships between solidification and properties. However, the inconsistent use of a particular solidification parameter for presenting materials characterization in the literature impedes inter-study comparability and the interpretation of findings. Therefore, there is a need for accurate expressions relating the solidification parameters for each alloy. In this study, A319 aluminum alloy castings were produced in a permanent mold with various preheating temperatures in order to control metal cooling. Analysis of the cooling curve for each casting enabled the identification of its liquidus, Al-Si eutectic, and solidus temperatures and times. These values led to the calculation of the primary solidification rate, total solidification rate, primary solidification time, and local solidification time for each casting, which were related to each other as well as to the average casting SDAS and material hardness. Expressions for each of their correlations have been presented with high coefficients of determination, which will aid in microstructural prediction and casting design.

Shelf sea tidal currents and mixing fronts determined from ocean glider observations

Science.gov (United States)

Sheehan, Peter M. F.; Berx, Barbara; Gallego, Alejandro; Hall, Rob A.; Heywood, Karen J.; Hughes, Sarah L.; Queste, Bastien Y.

2018-03-01

Tides and tidal mixing fronts are of fundamental importance to understanding shelf sea dynamics and ecosystems. Ocean gliders enable the observation of fronts and tide-dominated flows at high resolution. We use dive-average currents from a 2-month (12 October-2 December 2013) glider deployment along a zonal hydrographic section in the north-western North Sea to accurately determine M2 and S2 tidal velocities. The results of the glider-based method agree well with tidal velocities measured by current meters and with velocities extracted from the TPXO tide model. The method enhances the utility of gliders as an ocean-observing platform, particularly in regions where tide models are known to be limited. We then use the glider-derived tidal velocities to investigate tidal controls on the location of a front repeatedly observed by the glider. The front moves offshore at a rate of 0.51 km day-1. During the first part of the deployment (from mid-October until mid-November), results of a one-dimensional model suggest that the balance between surface heat fluxes and tidal stirring is the primary control on frontal location: as heat is lost to the atmosphere, full-depth mixing is able to occur in progressively deeper water. In the latter half of the deployment (mid-November to early December), a front controlled solely by heat fluxes and tidal stirring is not predicted to exist, yet a front persists in the observations. We analyse hydrographic observations collected by the glider to attribute the persistence of the front to the boundary between different water masses, in particular to the presence of cold, saline, Atlantic-origin water in the deeper portion of the section. We combine these results to propose that the front is a hybrid front: one controlled in summer by the local balance between heat fluxes and mixing and which in winter exists as the boundary between water masses advected to the north-western North Sea from diverse source regions. The glider observations

Shelf sea tidal currents and mixing fronts determined from ocean glider observations

Directory of Open Access Journals (Sweden)

P. M. F. Sheehan

2018-03-01

Full Text Available Tides and tidal mixing fronts are of fundamental importance to understanding shelf sea dynamics and ecosystems. Ocean gliders enable the observation of fronts and tide-dominated flows at high resolution. We use dive-average currents from a 2-month (12 October–2 December 2013 glider deployment along a zonal hydrographic section in the north-western North Sea to accurately determine M2 and S2 tidal velocities. The results of the glider-based method agree well with tidal velocities measured by current meters and with velocities extracted from the TPXO tide model. The method enhances the utility of gliders as an ocean-observing platform, particularly in regions where tide models are known to be limited. We then use the glider-derived tidal velocities to investigate tidal controls on the location of a front repeatedly observed by the glider. The front moves offshore at a rate of 0.51 km day−1. During the first part of the deployment (from mid-October until mid-November, results of a one-dimensional model suggest that the balance between surface heat fluxes and tidal stirring is the primary control on frontal location: as heat is lost to the atmosphere, full-depth mixing is able to occur in progressively deeper water. In the latter half of the deployment (mid-November to early December, a front controlled solely by heat fluxes and tidal stirring is not predicted to exist, yet a front persists in the observations. We analyse hydrographic observations collected by the glider to attribute the persistence of the front to the boundary between different water masses, in particular to the presence of cold, saline, Atlantic-origin water in the deeper portion of the section. We combine these results to propose that the front is a hybrid front: one controlled in summer by the local balance between heat fluxes and mixing and which in winter exists as the boundary between water masses advected to the north-western North Sea from diverse source

On the transition from short-range diffusion-limited to collision-limited growth in alloy solidification

International Nuclear Information System (INIS)

Aziz, M.J.; Boettinger, W.J.

1994-01-01

Short-range diffusion-limited growth, collision-limited growth, and the transition between the two regimes are explained as natural consequences of a single model for the kinetics of alloy solidification. Analytical expressions are developed for the velocity-undercooling function of a planar interface during dilute alloy solidification, using Turnbull's collision-limited growth model and the Continuous Growth Solute Trapping Model of Aziz and Kaplan both with and without a solute drag effect. The interface mobility, -dv/dT, is shown to be very high (proportional to the speed of sound) if the alloy is sufficiently dilute or if the growth rate is sufficiently rapid for nearly complete solute trapping. The interface mobility is reduced by the three orders of magnitude (becoming proportional to the diffusive speed) at intermediate growth rates where partial solute trapping occurs. Differences in low velocity predictions of the models with and without solute drag are also discussed. Comparison of the results of the analytical expressions to numerical solutions of the non-dilute kinetic model for Al-Be alloys shows that the dilute approximation breaks down at melt compositions on the order of 10 at.%. Similar variations in the interface mobility are shown for the disorder-trapping model of Boettinger and Aziz

On the Role of Mantle Overturn during Magma Ocean Solidification

Science.gov (United States)

Boukaré, C. E.; Parmentier, E.; Parman, S. W.

2017-12-01

Solidification of potential global magma ocean(s) (MO) early in the history of terrestrial planets may play a key role in the evolution of planetary interiors by setting initial conditions for their long-term evolution. Constraining this initial structure of solid mantles is thus crucial but remains poorly understood. MO fractional crystallization has been proposed to generate gravitationally unstable Fe-Mg chemical stratification capable of driving solid-state mantle overturn. Fractional solidification and overturn hypothesis, while only an ideal limiting case, can explain important geochemical features of both the Moon and Mars. Current overturn models consider generally post-MO overturn where the cumulate pile remains immobile until the end of MO solidification. However, if the cumulate pile overturns during MO solidification, the general picture of early planet evolution might differ significantly from the static crystallization models. We show that the timing of mantle overturn can be characterized with a dimensionless number measuring the ratio of the MO solidification time and the purely compositional overturn timescale. Syn-solidification overturn occurs if this dimensionless parameter, Rc, exceeds a critical value. Rc is mostly affected by the competition between the MO solidification time and mantle viscosity. Overturn that occurs during solidification can result in smaller scales of mantle chemical heterogeneity that could persist for long times thus influencing the whole evolution of a planetary body. We will discuss the effects of compaction/percolation on mantle viscosity. If partially molten cumulate do not have time to compact during MO solidification, viscosity of cumulates would be significantly lower as the interstitcial melt fraction would be large. Both solid mantle remelting during syn-solidification overturn and porous convection of melt retained with the cumulates are expected to reduce the degree of fractional crystallization. Syn-solidification

Finite element modelling of solidification phenomena

Indian Academy of Sciences (India)

Unknown

Abstract. The process of solidification process is complex in nature and the simulation of such process is required in industry before it is actually undertaken. Finite element method is used to simulate the heat transfer process accompanying the solidification process. The metal and the mould along with the air gap formation ...

Determination for the Entrapment Criterion of Non-metallic Inclusions by the Solidification Front During Steel Centrifugal Continuous Casting

Science.gov (United States)

Wang, Qiangqiang; Zhang, Lifeng

2016-06-01

In the current study, the three-dimensional fluid flow, heat transfer, and solidification in steel centrifugal continuous casting strands were simulated. The volume of fluid model was used to solve the multiphase phenomena between the molten steel and the air. The entrapment and final distribution of inclusions in the solidified shell were studied with the discussion on the effect of rotation behavior of the caster system. Main results indicate that after applying the rotation of the shell, the fluid flow transformed from a recirculation flow to a rotation flow in the mold region and was driven to flow around in the casting direction. As the distance below the meniscus increased, the distribution of the tangential speed of the flow and the centrifugal force along one diameter of the strand became symmetrical gradually. The jet flow from the nozzle hardly impinged on the same location on the shell due to the rotation of the shell during solidification. Thus, the shell thickness on the same height was uniform around, and the thinning shell and a hot spot on the surface of shell were avoided. Both of the measurement and the calculation about the distribution of oxide inclusions along the radial direction indicated the number of inclusions at the side and the center was more than that at the quarter on the cross section of billet. With a larger diameter, inclusions tended to be entrapped toward the center area of the billet.

Phase-Field Modeling of Polycrystalline Solidification: From Needle Crystals to Spherulites—A Review

Science.gov (United States)

Gránásy, László; Rátkai, László; Szállás, Attila; Korbuly, Bálint; Tóth, Gyula I.; Környei, László; Pusztai, Tamás

2014-04-01

Advances in the orientation-field-based phase-field (PF) models made in the past are reviewed. The models applied incorporate homogeneous and heterogeneous nucleation of growth centers and several mechanisms to form new grains at the perimeter of growing crystals, a phenomenon termed growth front nucleation. Examples for PF modeling of such complex polycrystalline structures are shown as impinging symmetric dendrites, polycrystalline growth forms (ranging from disordered dendrites to spherulitic patterns), and various eutectic structures, including spiraling two-phase dendrites. Simulations exploring possible control of solidification patterns in thin films via external fields, confined geometry, particle additives, scratching/piercing the films, etc. are also displayed. Advantages, problems, and possible solutions associated with quantitative PF simulations are discussed briefly.

Evolution of solidification texture during additive manufacturing

Science.gov (United States)

Wei, H. L.; Mazumder, J.; DebRoy, T.

2015-01-01

Striking differences in the solidification textures of a nickel based alloy owing to changes in laser scanning pattern during additive manufacturing are examined based on theory and experimental data. Understanding and controlling texture are important because it affects mechanical and chemical properties. Solidification texture depends on the local heat flow directions and competitive grain growth in one of the six preferred growth directions in face centered cubic alloys. Therefore, the heat flow directions are examined for various laser beam scanning patterns based on numerical modeling of heat transfer and fluid flow in three dimensions. Here we show that numerical modeling can not only provide a deeper understanding of the solidification growth patterns during the additive manufacturing, it also serves as a basis for customizing solidification textures which are important for properties and performance of components. PMID:26553246

Efficient estimation of diffusion during dendritic solidification

Science.gov (United States)

Yeum, K. S.; Poirier, D. R.; Laxmanan, V.

1989-01-01

A very efficient finite difference method has been developed to estimate the solute redistribution during solidification with diffusion in the solid. This method is validated by comparing the computed results with the results of an analytical solution derived by Kobayashi (1988) for the assumptions of a constant diffusion coefficient, a constant equilibrium partition ratio, and a parabolic rate of the advancement of the solid/liquid interface. The flexibility of the method is demonstrated by applying it to the dendritic solidification of a Pb-15 wt pct Sn alloy, for which the equilibrium partition ratio and diffusion coefficient vary substantially during solidification. The fraction eutectic at the end of solidification is also obtained by estimating the fraction solid, in greater resolution, where the concentration of solute in the interdendritic liquid reaches the eutectic composition of the alloy.

Advancement of Solidification Processing Technology Through Real Time X-Ray Transmission Microscopy: Sample Preparation

Science.gov (United States)

Stefanescu, D. M.; Curreri, P. A.

1996-01-01

Two types of samples were prepared for the real time X-ray transmission microscopy (XTM) characterization. In the first series directional solidification experiments were carried out to evaluate the critical velocity of engulfment of zirconia particles in the Al and Al-Ni eutectic matrix under ground (l-g) conditions. The particle distribution in the samples was recorded on video before and after the samples were directionally solidified. In the second series samples of the above two type of composites were prepared for directional solidification runs to be carried out on the Advanced Gradient Heating Facility (AGHF) aboard the space shuttle during the LMS mission in June 1996. X-ray microscopy proved to be an invaluable tool for characterizing the particle distribution in the metal matrix samples. This kind of analysis helped in determining accurately the critical velocity of engulfment of ceramic particles by the melt interface in the opaque metal matrix composites. The quality of the cast samples with respect to porosity and instrumented thermocouple sheath breakage or shift could be easily viewed and thus helped in selecting samples for the space shuttle experiments. Summarizing the merits of this technique it can be stated that this technique enabled the use of cast metal matrix composite samples since the particle location was known prior to the experiment.

Solidification microstructures of aluminium-uranium alloys

International Nuclear Information System (INIS)

Ambrozio Filho, F.; Vieira, R.R.

1976-01-01

The solidification of microstrutures of aluminium-uranium alloys in the range of 4 to 20% uranium is investigated. The solidification was obtained both in ingot molds and under controlled directional solidification. The conditions for the presence of primary crystals and eutectic are discussed and an analysis of the influence of variables (growth rate and thermal gradient in the liquid) on the alloy structure is made. The effect of cooling rate on the alloy structures has been determined. It is found that the resulting structure can be derived from the kinectics concept, as required by the coupled-zone theory. Suggestions on the qualitative intervals of composition and temperatures with eutectic growth are presented [pt

Polymer solidification national program

International Nuclear Information System (INIS)

Kalb, P.D.; Colombo, P.

1993-04-01

Brookhaven National Laboratory (BNL) has developed several new and innovative polymer processes for the solidification of low-level radioactive, hazardous and mixed wastes streams. Polyethylene and modified sulfur cement solidification technologies have undergone steady, gradual development at BNL over the past nine years. During this time they have progressed through each of the stages necessary for logical technology maturation: from process conception, parameter optimization, waste form testing, evaluation of long-term durability, economic analysis, and scale-up feasibility. This technology development represents a significant investment which can potentially provide DOE with both short- and long-term savings

Finite-time barriers to reaction front propagation

Science.gov (United States)

Locke, Rory; Mahoney, John; Mitchell, Kevin

2015-11-01

Front propagation in advection-reaction-diffusion systems gives rise to rich geometric patterns. It has been shown for time-independent and time-periodic fluid flows that invariant manifolds, termed burning invariant manifolds (BIMs), serve as one-sided dynamical barriers to the propagation of reaction front. More recently, theoretical work has suggested that one-sided barriers, termed burning Lagrangian Coherent structures (bLCSs), exist for fluid velocity data prescribed over a finite time interval, with no assumption on the time-dependence of the flow. In this presentation, we use a time-varying fluid ``wind'' in a double-vortex channel flow to demonstrate that bLCSs form the (locally) most attracting or repelling fronts.

Free-surface velocity measurements using an optically recording velocity interferometer

International Nuclear Information System (INIS)

Lu Jianxin; Wang Zhao; Liang Jing; Shan Yusheng; Zhou Chuangzhi; Xiang Yihuai; Lu Ze; Tang Xiuzhang

2006-01-01

An optically recording velocity interferometer system (ORVIS) was developed for the free-surface velocity measurements in the equation of state experiments. The time history of free-surface velocity could be recorded by the electronic streak camera. In the experiments, ORVIS got a 179 ps time resolution, and a higher time resolution could be got by minimizing the delay time. The equation of state experiments were carried out on the high power excimer laser system called 'Heaven I' with laser wavelength of 248.4 nm, pulse duration of 25 ns and maximum energy 158 J. Free-surface velocity of 20 μm thick iron got 3.86 km/s with laser intensity of 6.24 x 10 11 W·cm -2 , and free-surface velocity of 100 μm thick aluminum with 100 μm CH foil at the front got 2.87 km/s with laser intensity 7.28 x 10 11 W·cm -2 . (authors)

Solidification with back-diffusion of irregular eutectics

Directory of Open Access Journals (Sweden)

M. Trepczyńska-Łent

2008-10-01

Full Text Available The definition of the α - parameter back-diffusion has been introduced in the work. The alternative models of solidification were describedtaking into consideration back-diffusion process. The possibility of using those models for eutectic alloys solidification is worthyof interest.

Solidification control in continuous casting of steel

Indian Academy of Sciences (India)

Unknown

Solidification in continuous casting (CC) technology is initiated in a water- ..... to fully austenitic solidification, and FP between 0 and 1 indicates mixed mode. ... the temperature interval (LIT – TSA) corresponding to fs = 0⋅9 → 1, is in reality the.

Solidification at the micro-scale

International Nuclear Information System (INIS)

Howe, A.

2003-01-01

The experimental determination and computer simulation of the micro-segregation accompanying the solidification of alloys continues to be a subject of much academic and industrial interest. Both are subject to progressively more sophisticated analyses, and a discussion is offered regarding the development and practical use of such studies. Simple steels are particularly difficult targets for such work: solidification does not end conveniently in a eutectic, the rapid diffusion particularly in the delta-ferrite phase obscures most evidence of what had occurred at the micro-scale during solidification, and one or more subsequent solid state phase transformations further obscure such details. Also, solidification at the micro-scale is inherently variable: the usual, dendrite morphologies encountered are, after all, instabilities in growth behaviour, and therefore such variability should be expected. For questions such as the relative susceptibility of different grades to particular problems, it is the average, typical behaviour that is of interest, whereas for other questions such as the on-set of macro-segregation, the local variability is paramount. Depending on the question being asked, and indeed the accuracy with which validatory data are available, simple pseudo-analytical equations employing various limiting assumptions, or sophisticated models which remove the need for most such limitations, could be appropriate. This paper highlights the contribution to such studies of various collaborative research forums within the European Union with which the author is involved. (orig.) [de

Measurements of ion velocity separation and ionization in multi-species plasma shocks

Science.gov (United States)

Rinderknecht, Hans G.; Park, H.-S.; Ross, J. S.; Amendt, P. A.; Wilks, S. C.; Katz, J.; Hoffman, N. M.; Kagan, G.; Vold, E. L.; Keenan, B. D.; Simakov, A. N.; Chacón, L.

2018-05-01

The ion velocity structure of a strong collisional shock front in a plasma with multiple ion species is directly probed in laser-driven shock-tube experiments. Thomson scattering of a 263.25 nm probe beam is used to diagnose ion composition, temperature, and flow velocity in strong shocks ( M ˜6 ) propagating through low-density ( ρ˜0.1 mg/cc) plasmas composed of mixtures of hydrogen (98%) and neon (2%). Within the preheat region of the shock front, two velocity populations of ions are observed, a characteristic feature of strong plasma shocks. The ionization state of the Ne is observed to change within the shock front, demonstrating an ionization-timescale effect on the shock front structure. The forward-streaming proton feature is shown to be unexpectedly cool compared to predictions from ion Fokker-Planck simulations; the neon ionization gradient is evaluated as a possible cause.

Development of a high velocity rain erosion test method

Energy Technology Data Exchange (ETDEWEB)

Chung, Dong Teak; Jin, Doo Han [Korea University of Technology and Education, Cheonan (Korea, Republic of); Kang, Hyung [Agency for Defense Development, Daejeon (Korea, Republic of)

2009-07-01

The nose of a missile, flying through raining region with a supersonic speed, is subjected to the rain erosion because the nose is made of a brittle ceramic material. A simple yet very effective rain erosion test method is developed. The sabot assembly similar to the hypodermic syringe carries specific amount of water is launched by a low pressure air gun. After the stopper stop the sabot assembly by impact, the steel plunger continues moving toward to squeeze the silicon rubber in front. The pressurized silicon rubber then is squeezed through the orifice in front of the sabot at high velocity, thus, accelerates the water droplet to higher velocity. The droplet velocity up to 800m/s is successfully attained using a low pressure air gun. The ceramic specimen assembly is placed in front of the high speed water droplet and the rain erosion damage on the surface of the specimen is observed.

Optimization of heat transfer during the directional solidification process of 1600 kg silicon feedstock

Science.gov (United States)

Hu, Chieh; Chen, Jyh Chen; Nguyen, Thi Hoai Thu; Hou, Zhi Zhong; Chen, Chun Hung; Huang, Yen Hao; Yang, Michael

2018-02-01

In this study, the power ratio between the top and side heaters and the moving velocity of the side insulation are designed to control the shape of the crystal-melt interface during the growth process of a 1600 kg multi-crystalline silicon ingot. The power ratio and insulation gap are adjusted to ensure solidification of the melt. To ensure that the crystal-melt interface is slightly convex in relation to the melt during the entire solidification process, the power ratio should be augmented gradually in the initial stages while being held to a constant value in the middle stages. Initially the gap between the side and the bottom insulation is kept small to reduce thermal stress inside the seed crystals. However, the growth rate will be slow in the early stages of the solidification process. Therefore, the movement of the side insulation is fast in the initial stages but slower in the middle stages. In the later stages, the side insulation gap is fixed. With these modifications, the convexity of the crystal-melt interface in relation to the melt can be maintained during the growth process with an approximately 41% reduction in the thermal stress inside the growing ingot and an 80% reduction in dislocation density along the center line of the ingot compared with the original case.

Advanced modeling of solidification

International Nuclear Information System (INIS)

Bousquet-Melou, P.; Fichot, F.; Goyeau, B.; Gobin, D.; Quintard, M.

2001-01-01

A theoretical and numerical macroscopic modeling of the solidification of binary mixtures is presented. The growth of a solid-liquid region (mushy zone), represented by a non-homogeneous porous medium, is considered. A macroscopic model for momentum, heat and mass transfer during solidification is derived using the volume averaging method, and the effective transport properties (permeability, effective diffusivities, mass exchange coefficients) are defined by associated closure problems (set of microscopic balance equations). Consequently, the effects of the dendritic geometry (tortuosity) and of microscopic transfer phenomena (dispersion, interfacial exchange) are introduced in the averaged balance equations and in the representation of the effective transport coefficients. This closure method provides an original approach of solidification modeling. The resulting macroscopic model is based on the local thermal equilibrium assumption (one-temperature model) while a two-phase description of macroscopic species transfer is introduced using solid and liquid mass exchange coefficients. The phase diagram is used to predict the solid and liquid equilibrium concentrations at the solid-liquid interface. This two-phase approach extends the classical limiting cases that correspond to the lever-rule and Scheil descriptions. (authors)

Plastic solidification system at Hamaoka Nuclear Power Station

International Nuclear Information System (INIS)

Okajima, Hiroyuki; Iokibe, Hiroyuki; Tsukiyama, Shigeru; Suzuki, Michio; Yamaguchi, Masato

1987-01-01

In Unit 1 and 2 of the Hamaoka Nuclear Power Station, radioactive waste was previously solidified in cement. By this method, the quantity of waste thus treated is relatively small, resulting in large number of the solidified drums. In order to solve this problem, the solidification facility using a thermosetting resin was employed, which is in operation since January 1986 for Unit 1, 2 and 3. As compared with the cement solidification, the solidified volume of concentrated liquid is about 1/12 and of spent-resin slurry is about 1/4 in plastic solidification. The following are described: course leading to the employment, the plastic solidification facility, features of the facility, operation results so far with the facility, etc. (Mori, K.)

Solidification of oils and organic liquids

International Nuclear Information System (INIS)

Clark, D.E.; Colombo, P.; Neilson, R.M. Jr.

1982-07-01

The suitability of selected solidification media for application in the disposal of low-level oil and other organic liquid wastes has been investigated. In the past, these low-level wastes (LLWs) have commonly been immobilized by sorption onto solid absorbents such as vermiculite or diatomaceous earth. Evolving regulations regarding the disposal of these materials encourage solidification. Solidification media which were studied include Portland type I cement; vermiculite plus Portland type I cement; Nuclear Technology Corporation's Nutek 380-cement process; emulsifier, Portland type I cement-sodium silicate; Delaware Custom Materiel's cement process; and the US Gypsum Company's Envirostone process. Waste forms have been evaluated as to their ability to reliably produce free standing monolithic solids which are homogeneous (macroscopically), contain < 1% free standing liquids by volume and pass a water immersion test. Solidified waste form specimens were also subjected to vibratory shock testing and flame testing. Simulated oil wastes can be solidified to acceptable solid specimens having volumetric waste loadings of less than 40 volume-%. However, simulated organic liquid wastes could not be solidified into acceptable waste forms above a volumetric loading factor of about 10 volume-% using the solidification agents studied

General characteristics of eutectic alloy solidification mechanisms

International Nuclear Information System (INIS)

Lemaignan, Clement.

1977-01-01

The eutectic alloy sodification was studied in binary systems: solidification of non facetted - non facetted eutectic alloy (theoretical aspects, variation of the lamellar spacing, crystallographic relation between the various phases); solidification of facetted - non facetted eutectic alloy; coupled growth out of eutectic alloy; eutectic nucleation [fr

Investigation of Three-Dimensional Axisymmetric Unsteady Stagnation-Point Flow and Heat Transfer Impinging on an Accelerated Flat Plate

OpenAIRE

ali shokrgozar abbasi; Asghar Baradaran Rahimi; Hamidreza Mozayeni

2016-01-01

General formulation and solution of Navier-Stokes and energy equations are sought in the study of threedimensional axisymmetric unsteady stagnation-point flow and heat transfer impinging on a flat plate when the plate is moving with variable velocity and acceleration towards the main stream or away from it. As an application, among others, this accelerated plate can be assumed as a solidification front which is being formed with variable velocity. An external fluid, along z - directi...

Simulation of microstructural evolution in directional solidification of Ti-45at.%Al alloy using cellular automaton method

Directory of Open Access Journals (Sweden)

Wang Kuangfei

2010-02-01

Full Text Available The microstructural evolution of Ti-45 at.%Al alloy during directional solidification was simulated by applying a solute diffusion controlled solidification model. The obtained results have shown that under high thermal gradients the stable primary spacing can be adjusted via branching or competitive growth. For dendritic structures formed under a high thermal gradient, the secondary dendrite arms are developed not very well in many cases due to the branching mechanism under a constrained dendritic growth condition. Furthermore, it has been observed that, with increasing pulling velocity, there exists a cell/dendrite transition region consisting of cells and dendrites, which varies with the thermal gradient in a contradicting way, i.e. increase of the thermal gradient leading to the decrease of the range of the transition region. The simulations agree reasonably well with experiment results.

Doping front migration in intrinsically conductive polymers and its electrochemical modulation by a separate electrode

International Nuclear Information System (INIS)

Rahmanian, Afsaneh; Knoll, Meinhard

2012-01-01

Highlights: ► We modify the doping front migration process. ► The migration velocity is controlled by a separate electrode. ► The process may be used in “best use before” labels. - Abstract: We demonstrate a new method of modifying the doping front migration process in multilayer structures, enabling the control of migration velocity. The presence of two interfaces in contact with the migration layer strongly affects the migration mechanism. Electrochemical switching of an electrode at one interface may be used to control the chemical doping front migration at the second interface. The process may be used to produce ultralow-cost devices acting as electronic “best use before” labels on food and drink or “use-by” labels on drugs. Control of the migration velocity may be used as a method for weighting storage conditions (i.e. opening of a package during the measurement period increases the migration velocity).

Localized melt-scan strategy for site specific control of grain size and primary dendrite arm spacing in electron beam additive manufacturing

International Nuclear Information System (INIS)

Raghavan, Narendran; Simunovic, Srdjan; Dehoff, Ryan; Plotkowski, Alex; Turner, John; Kirka, Michael; Babu, Suresh

2017-01-01

In addition to design geometry, surface roughness, and solid-state phase transformation, solidification microstructure plays a crucial role in controlling the performance of additively manufactured components. Crystallographic texture, primary dendrite arm spacing (PDAS), and grain size are directly correlated to local solidification conditions. We have developed a new melt-scan strategy for inducing site specific, on-demand control of solidification microstructure. We were able to induce variations in grain size (30 μm–150 μm) and PDAS (4 μm - 10 μm) in Inconel 718 parts produced by the electron beam additive manufacturing system (Arcam ® ). A conventional raster melt-scan resulted in a grain size of about 600 μm. The observed variations in grain size with different melt-scan strategies are rationalized using a numerical thermal and solidification model which accounts for the transient curvature of the melt pool and associated thermal gradients and liquid-solid interface velocities. The refinement in grain size at high cooling rates (>10 4  K/s) is also attributed to the potential heterogeneous nucleation of grains ahead of the epitaxially growing solidification front. The variation in PDAS is rationalized using a coupled numerical-theoretical model as a function of local solidification conditions (thermal gradient and liquid-solid interface velocity) of the melt pool.

Enthalpies of a binary alloy during solidification

Science.gov (United States)

Poirier, D. R.; Nandapurkar, P.

1988-01-01

The purpose of the paper is to present a method of calculating the enthalpy of a dendritic alloy during solidification. The enthalpies of the dendritic solid and interdendritic liquid of alloys of the Pb-Sn system are evaluated, but the method could be applied to other binaries, as well. The enthalpies are consistent with a recent evaluation of the thermodynamics of Pb-Sn alloys and with the redistribution of solute in the same during dendritic solidification. Because of the heat of mixing in Pb-Sn alloys, the interdendritic liquid of hypoeutectic alloys (Pb-rich) of less than 50 wt pct Sn has enthalpies that increase as temperature decreases during solidification.

Containerless solidification of acoustically levitated Ni-Sn eutectic alloy

Energy Technology Data Exchange (ETDEWEB)

Geng, D.L.; Xie, W.J.; Wei, B. [Northwestern Polytechnical University, Department of Applied Physics, Xi' an (China)

2012-10-15

Containerless solidification of Ni-18.7at%Sn eutectic alloy has been achieved with a single-axis acoustic levitator. The temperature, motion, and oscillation of the sample were monitored by a high speed camera. The temperature of the sample can be determined from its image brightness, although the sample moves vertically and horizontally during levitation. The experimentally observed frequency of vertical motion is in good agreement with theoretical prediction. The sample undergoes shape oscillation before solidification finishes. The solidification microstructure of this alloy consists of a mixture of anomalous eutectic plus regular lamellar eutectic. This indicates the achievement of rapid solidification under acoustic levitation condition. (orig.)

Detection of moving capillary front in porous rocks using X-ray and ultrasonic methods

Directory of Open Access Journals (Sweden)

Christian eDavid

2015-07-01

Full Text Available Several methods are compared for the detection of moving capillary fronts in spontaneous imbibition experiments where water invades dry porous rocks. These methods are: (i the continuous monitoring of the mass increase during imbibition, (ii the imaging of the water front motion using X-ray CT scanning, (iii the use of ultrasonic measurements allowing the detection of velocity, amplitude and spectral content of the propagating elastic waves, and (iv the combined use of X-ray CT scanning and ultrasonic monitoring. It is shown that the properties of capillary fronts depend on the heterogeneity of the rocks, and that the information derived from each method on the dynamics of capillary motion can be significantly different. One important result from the direct comparison of the moving capillary front position and the P wave attributes is that the wave amplitude is strongly impacted before the capillary front reaches the sensors, in contrast with the velocity change which is concomitant with the fluid front arrival in the sensors plane.

Solidification microstructures and solid-state parallels: Recent developments, future directions

Energy Technology Data Exchange (ETDEWEB)

Asta, M. [Department of Chemical Engineering and Materials Science, University of California at Davis, Davis, CA 95616 (United States); Beckermann, C. [Department of Mechanical and Industrial Engineering, University of Iowa, Iowa City, IA 52242 (United States); Karma, A. [Department of Physics and Center for Interdisciplinary Research on Complex Systems, Northeastern University, Boston, MA 02115 (United States); Kurz, W. [Institute of Materials, Ecole Polytechnique Federale de Lausanne (EPFL), 1015 Lausanne (Switzerland)], E-mail: wilfried.kurz@epfl.ch; Napolitano, R. [Department of Materials Science and Engineering, Iowa State University, and Ames Laboratory USDOE, Ames, IA 50011 (United States); Plapp, M. [Physique de la Matiere Condensee, Ecole Polytechnique, CNRS, 91128 Palaiseau (France); Purdy, G. [Department of Materials Science and Engineering, McMaster University, Hamilton, Ont., L8S 4L7 (Canada); Rappaz, M. [Institute of Materials, Ecole Polytechnique Federale de Lausanne (EPFL), 1015 Lausanne (Switzerland); Trivedi, R. [Department of Materials Science and Engineering, Iowa State University, and Ames Laboratory USDOE, Ames, IA 50011 (United States)

2009-02-15

Rapid advances in atomistic and phase-field modeling techniques as well as new experiments have led to major progress in solidification science during the first years of this century. Here we review the most important findings in this technologically important area that impact our quantitative understanding of: (i) key anisotropic properties of the solid-liquid interface that govern solidification pattern evolution, including the solid-liquid interface free energy and the kinetic coefficient; (ii) dendritic solidification at small and large growth rates, with particular emphasis on orientation selection; (iii) regular and irregular eutectic and peritectic microstructures; (iv) effects of convection on microstructure formation; (v) solidification at a high volume fraction of solid and the related formation of pores and hot cracks; and (vi) solid-state transformations as far as they relate to solidification models and techniques. In light of this progress, critical issues that point to directions for future research in both solidification and solid-state transformations are identified.

Effect of Temperature and Fluid Flow on Dendrite Growth During Solidification of Al-3 Wt Pct Cu Alloy by the Two-Dimensional Cellular Automaton Method

Science.gov (United States)

Gu, Cheng; Wei, Yanhong; Liu, Renpei; Yu, Fengyi

2017-12-01

A two-dimensional cellular automaton-finite volume model was developed to simulate dendrite growth of Al-3 wt pct Cu alloy during solidification to investigate the effect of temperature and fluid flow on dendrite morphology, solute concentration distribution, and dendrite growth velocity. Different calculation conditions that may influence the results of the simulation, including temperature and flow, were considered. The model was also employed to study the effect of different undercoolings, applied temperature fields, and forced flow velocities on solute segregation and dendrite growth. The initial temperature and fluid flow have a significant impact on the dendrite morphologies and solute profiles during solidification. The release of energy is operated with solidification and results in the increase of temperature. A larger undercooling leads to larger solute concentration near the solid/liquid interface and solute concentration gradient at the same time-step. Solute concentration in the solid region tends to increase with the increase of undercooling. Four vortexes appear under the condition when natural flow exists: the two on the right of the dendrite rotate clockwise, and those on the left of the dendrite rotate counterclockwise. With the increase of forced flow velocity, the rejected solute in the upstream region becomes easier to be washed away and enriched in the downstream region, resulting in acceleration of the growth of the dendrite in the upstream and inhibiting the downstream dendrite growth. The dendrite perpendicular to fluid flow shows a coarser morphology in the upstream region than that of the downstream. Almost no secondary dendrite appears during the calculation process.

Solidification effects on sill formation: An experimental approach

Science.gov (United States)

Chanceaux, L.; Menand, T.

2014-10-01

Sills represent a major mechanism for constructing continental Earth's crust because these intrusions can amalgamate and form magma reservoirs and plutons. As a result, numerous field, laboratory and numerical studies have investigated the conditions that lead to sill emplacement. However, all previous studies have neglected the potential effect magma solidification could have on sill formation. The effects of solidification on the formation of sills are studied and quantified with scaled analogue laboratory experiments. The experiments presented here involved the injection of hot vegetable oil (a magma analogue) which solidified during its propagation as a dyke in a colder and layered solid of gelatine (a host rock analogue). The gelatine solid had two layers of different stiffness, to create a priori favourable conditions to form sills. Several behaviours were observed depending on the injection temperature and the injection rate: no intrusions (extreme solidification effects), dykes stopping at the interface (high solidification effects), sills (moderate solidification effects), and dykes passing through the interface (low solidification effects). All these results can be explained quantitatively as a function of a dimensionless temperature θ, which describes the experimental thermal conditions, and a dimensionless flux ϕ, which describes their dynamical conditions. The experiments reveal that sills can only form within a restricted domain of the (θ , ϕ) parameter space. These experiments demonstrate that contrary to isothermal experiments where cooling could not affect sill formation, the presence of an interface that would be a priori mechanically favourable is not a sufficient condition for sill formation; solidification effects restrict sill formation. The results are consistent with field observations and provide a means to explain why some dykes form sills when others do not under seemingly similar geological conditions.

Chemical radwaste solidification processes

International Nuclear Information System (INIS)

Malloy, C.W.

1979-01-01

Some of these processes and their problems are briefly reviewed: early cement systems; urea-formaldehyde; Dow solidification process; low-viscosity chemical agents (POLYPAC); and water-extensible polyester. 9 refs

Effects of Non-equilibrium Solidification on the Material Properties of Brick Silicon for Photovoltaics

Science.gov (United States)

Regnault, W. F.; Yoo, K. C.; Soltani, P. K.; Johnson, S. M.

1984-01-01

Silicon ingot growth technologies like the Ubiquitous Crystallization Process (UCP) are solidified within a shaping crucible. The rate at which heat can be lost from this crucible minus the rate at which heat is input from an external source determines the rate at which crystallization will occur. Occasionally, when the process parameters for solidification are exceeded, the normally large multi-centimeter grain size material assocated with the UCP will break down into regions containing extremely small, millimeter or less, grain size material. Accompanying this breakdown in grain growth is the development of so called sinuous grain boundaries. The breakdown in grain growth which results in this type of small grain structure with sinuous boundaries is usually associated with the rapid crystallization that would accompany a system failure. This suggests that there are limits to the growth velocity that one can obtain and still expect to produce material that would possess good photovoltaic properties. It is the purpose to determine the causes behind the breakdown of this material and what parameters will determine the best rates of solidification.

Evaluation of Front Morphological Development of Reactive Solute Transport Using Behavior Diagrams

Directory of Open Access Journals (Sweden)

Jui-Sheng Chen

2009-01-01

Full Text Available While flowing through porous medium, ground water flow dissolves minerals thereby in creasing medium porosity and ultimately permeability. Reactive fluid flows preferentially into highly permeable zones, which are therefore dissolved most rapidly, producing a further preferential permeability enhancement. Accordingly, slight non-uniformities present in porous medium can be amplified and lead to fingering reaction fronts. The objective of this study is to investigate dissolution-induced porosity changes on reaction front morphology in homogeneous porous medium with two non-uniformities. Four controlling parameters, including up stream pressure gradient, reaction rate constant, non-uniformities spacing and non-uniformity strength ratio are comprehensively considered. By using a modified version of the numerical code, NSPCRT, to conduct a series of numerical simulations, front behavior diagrams are constructed to illustrate the morphologies of reaction fronts under various combinations of these four factors. Simulation results indicate that the two non-uniformities are inhibited into a planar front under low up stream pressure gradient, merge into a single-fingering front under inter mediate up stream pressure gradient, or grow into a double-fingers front under high up stream pressure gradient. More over, the two non-uniformities tend to develop intoadouble-fingering front as the non-uniformity strength ratio in creases from 0.2 to 1.0, and merge into a single-fingering front while the non-uniformity strength ratio in creases from 1.0 to 1.8. When the reaction rate constant is small, the two non-uniformities merge into a single front. Reaction rate constant significantly affects front advancing velocity. The front advancing velocity decreases with the reaction rate constant. Based on these results, front behavior diagrams which de fine the morphologies of the reaction fronts for these four parameters are constructed. Moreover, non

Optimisation of the microstructure of YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} superconducting ceramics textured by horizontal solidification. Effects of a magnetic field applied vertically during the solidification process; Optimisation de la microstructure de ceramiques supraconductrices texturees YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} par solidification horizontale. Effets de l`application d`un champ magnetique vertical au cours de la croissance

Energy Technology Data Exchange (ETDEWEB)

Durand, L

1995-12-14

We have shown that il was possible to disperse in a very homogeneous way, into the 123 matrix, 211 particles regular in size around 1{mu}m, by directional solidification of a mixture of 123 plus 211 sol-gel powders. The addition of 0.5 wt% of Pt lo this precursor mixture has permitted us to refine further the size of the 211 particles. Moreover, we have established that the finer the 123 powder and the faster the heating rate, the smaller the 211 particles. From another hand, we have found that the size and the microstructure of the solidified single domain was dependant upon numerous parameters. In particular, we have noted that if the cold pressed green body was not sintered before being melted, grains of solid CuO appeared into the liquid which next hardly recombined with it, giving rise to a comb like solidification front, witness of a local un-stability. Moreover, in these particular conditions, the 123 formed was found to be understoichiometric in Cu and the single domains severely limited in extension. Finally, we have observed that the application of a 4 T magnetic field during the solidification of a bar the longest axis of which was horizontal tended to align the c axis of the 123 grains parallel to the field. Incidentally, we have discovered that in the same conditions, the 211 particles trapped into the 123 matrix were also preferentially oriented. (author).

Rapid Solidification of AB{sub 5} Hydrogen Storage Alloys

Energy Technology Data Exchange (ETDEWEB)

Gulbrandsen-Dahl, Sverre

2002-01-01

thesis the changes of the crystal structure and the grain structure of La{sub 0.60}Ce{sub 0.29}Pr{sub 0.04}Nd{sub 0.07}Ni{sub 3.37}Co{sub 0.79}Mn{sub 0.25}Al{sub 0.7}= cooling rate during chill-block melt spinning are described. Totally, the material was rapidly solidified at 9 different cooling rates. The grain structure, crystallographic texture and the lattice parameters were studied by means of electron microscopy and powder X-ray diffraction. Additionally, the density of the rapidly solidified materials was measured by a gas pycnometer. All these properties were found to change with increasing cooling rate. The grain size decreased continuously with increasing cooling rate and was in the range of 1-5 {mu}m. The strength of the crystallographic texture first increased and then decreased with increasing cooling rate. Transmission electron microscopy studies revealed that the grains contained a large amount of crystallographic twins and that the solidification morphology changed from cellular to plane front at a cooling rate during solidification of approximately 6*10{sup 4} Ks{sup -1}. The unit cell volume and the density followed the same pattern with increasing cooling rate and decreased within each solidification morphology, but at the cooling rate from which the morphology changed, both these parameters suddenly increased. The identical variations in the unit cell volume and the density is explained by formation of excess lattice vacancies during rapid solidification. In Part IV of the thesis rapid solidification of the materials La{sub 0.60}Ce{sub 0.27}Pr{sub 0.04}Nd{sub 0.09}Ni{sub 4.76}Sn{sub 0.24} and LaNi{sub 4.76}Sn different cooling rates are described. The materials were analysed by means of electron microscopy and powder X-ray diffraction. The grain structures of both alloys were found to be in the nanometer range, and the grain sizes were almost invariant with increasing cooling rate. Furthermore, the lattice parameters of these materials were almost

Numerical study of the spreading and solidification of a molten particle impacting onto a rigid substrate under plasma spraying conditions

Directory of Open Access Journals (Sweden)

Oukach Soufiane

2015-01-01

Full Text Available This paper deals with simulation of the spreading and solidification of a fully molten particle impacting onto a preheated substrate under traditional plasma spraying conditions. The multiphase problem governing equations of mass, momentum and energy conservation taking into account heat transfer by conduction, convection and phase change are solved by using a Finite Element approach. The interface between molten particle and surrounding air, is tracked using the Level Set method. The effect of the Reynolds number on the droplet spreading and solidification, using a wide range of impact velocities (40-250m/s, is reported. A new correlation that predicts the final spread factor of splat as a function of Reynolds number is obtained. Thermal contact resistance, viscous dissipation, wettability and surface tension forces effects are taken into account.

Numerical study on morphology and solidification characteristics of successive droplet depositions on a substrate

Science.gov (United States)

Adaikalanathan, Vimalan

accounting for the latent heat. It is coupled with the flow solver through an Enthalpy-Porosity technique. A modified boundary condition which incorporates the contact resistance has also been implemented. The case of multiple eutectic solder droplet depositions has been simulated to study the various aspects of splat morphology and solidification characteristics. Effects of impact conditions on single as well as successive droplet depositions have been examined. The role of convection terms in the energy equation has been emphasized and quantitatively analysed. The effect of impact velocity is manifested as surface curvature of the pre-solidified splat and in turn, affects morphology of the subsequent droplets. Initial droplet temperature influences the solidification time of both single and multiple droplets. Under certain conditions, remelting of pre-solidified splat has been observed and its causes have been discussed. Contact resistance has been reported in the literature and has been found to have a strong influence not only on the heat transfer but also the spreading behaviour. Frequency of successive impingements is also an important factor affecting the metallurgical bonding properties.

Polymer Solidification Technology - Technical Issues and Challenges

International Nuclear Information System (INIS)

Jensen, Charles; Kim, Juyoul

2010-01-01

Many factors come into play, most of which are discovered and resolved only during full-scale solidification testing of each of the media commonly used in nuclear power plants. Each waste stream is unique, and must be addressed accordingly. This testing process is so difficult that Diversified's Vinyl Ester Styrene and Advanced Polymer Solidification are the only two approved processes in the United States today. This paper summarizes a few of the key obstacles that must be overcome to achieve a reliable, repeatable process for producing an approved Stable Class B and C waste form. Before other solidification and encapsulation technologies can be considered compliant with the requirements of a Stable waste form, the tests, calculations and reporting discussed above must be conducted for both the waste form and solidification process used to produce the waste form. Diversified's VERI TM and APS TM processes have gained acceptance in the UK. These processes have also been approved and gained acceptance in the U. S. because we have consistently overcome technical hurdles to produce a complaint product. Diversified Technologies processes are protected intellectual property. In specific instances, we have patents pending on key parts of our process technology

On the propagation of a coupled saturation and pressure front

Energy Technology Data Exchange (ETDEWEB)

Vasco, D. W.

2010-12-01

Using an asymptotic technique, valid for a medium with smoothly varying heterogeneity, I derive an expression for the velocity of a propagating, coupled saturation and pressure front. Due to the nonlinearity of the governing equations, the velocity of the propagating front depends upon the magnitude of the saturation and pressure changes across the front in addition to the properties of the medium. Thus, the expression must be evaluated in conjunction with numerical reservoir simulation. The propagation of the two-phase front is governed by the background saturation distribution, the saturation-dependent component of the fluid mobility, the porosity, the permeability, the capillary pressure function, the medium compressibility, and the ratio of the slopes of the relative permeability curves. Numerical simulation of water injection into a porous layer saturated with a nonaqueous phase liquid indicates that two modes of propagation are important. The fastest mode of propagation is a pressure-dominated disturbance that travels through the saturated layer. This is followed, much later, by a coupled mode with a large saturation change. These two modes are also observed in a simulation using a heterogeneous porous layer. A comparison between the propagation times estimated from the results of the numerical simulation and predictions from the asymptotic expression indicates overall agreement.

Does laser-driven heat front propagation depend on material microstructure?

Science.gov (United States)

Colvin, J. D.; Matsukuma, H.; Fournier, K. B.; Yoga, A.; Kemp, G. E.; Tanaka, N.; Zhang, Z.; Kota, K.; Tosaki, S.; Ikenouchi, T.; Nishimura, H.

2016-10-01

We showed earlier that the laser-driven heat front propagation velocity in low-density Ti-silica aerogel and TiO2 foam targets was slower than that simulated with a 2D radiation-hydrodynamics code incorporating an atomic kinetics model in non-LTE and assuming initially homogeneous material. Some theoretical models suggest that the heat front is slowed over what it would be in a homogeneous medium by the microstructure of the foam. In order to test this hypothesis we designed and conducted a comparison experiment on the GEKKO laser to measure heat front propagation velocity in two targets, one an Ar/CO2 gas mixture and the other a TiO2 foam, that had identical initial densities and average ionization states. We found that the heat front traveled about ten times faster in the gas than in the foam. We present the details of the experiment design and a comparison of the data with the simulations. This work was performed under the auspices of the U.S. Department of Energy by LLNL under Contract No. DE-AC52-07NA27344, and the joint research project of ILE Osaka U. (contract Nos. 2014A1-04 and 2015A1-02).

Solidification paths in modified Inconel 625 weld overlay material

DEFF Research Database (Denmark)

Chandrasekaran, Karthik; Tiedje, Niels Skat; Hald, John

2009-01-01

Inconel 625 is commonly used for overlay welding to protect the base metal against high temperature corrosion. The efficiency of corrosion protection depends on effective mixing of the overlay weld with the base metal and the subsequent segregation of alloy elements during solidification....... Metallographic analysis of solidified samples of Inconel 625 with addition of selected elements is compared with thermodynamic modelling of segregation during solidification. The influence of changes in the melt chemistry on the formation of intermetallic phases during solidification is shown. In particular...

Simulations of rapid pressure-induced solidification in molten metals

International Nuclear Information System (INIS)

Patel, Mehul V.; Streitz, Frederick H.

2004-01-01

The process of interest in this study is the solidification of a molten metal subjected to rapid pressurization. Most details about solidification occurring when the liquid-solid coexistence line is suddenly transversed along the pressure axis remain unknown. We present preliminary results from an ongoing study of this process for both simple models of metals (Cu) and more sophisticated material models (MGPT potentials for Ta). Atomistic (molecular dynamics) simulations are used to extract details such as the time and length scales that govern these processes. Starting with relatively simple potential models, we demonstrate how molecular dynamics can be used to study solidification. Local and global order parameters that aid in characterizing the phase have been identified, and the dependence of the solidification time on the phase space distance between the final (P,T) state and the coexistence line has been characterized

Directional Solidification and Liquidus Projection of the Sn-Co-Cu System

Science.gov (United States)

Chen, Sinn-Wen; Chang, Jui-Shen; Pan, Kevin; Hsu, Chia-Ming; Hsu, Che-Wei

2013-04-01

This study investigates the Sn-Co-Cu ternary system, which is of interest to the electronics industry. Ternary Sn-Co-Cu alloys were prepared, their as-solidified microstructures were examined, and their primary solidification phases were determined. The primary solidification phases observed were Cu, Co, Co3Sn2, CoSn, CoSn2, Cu6Sn5, Co3Sn2, γ, and β phases. Although there are ternary compounds reported in this ternary system, no ternary compound was found as the primary solidification phase. The directional solidification technique was applied when difficulties were encountered using the conventional quenching method to distinguish the primary solidification phases, such as Cu6Sn5, Cu3Sn, and γ phases. Of all the primary solidification phases, the Co3Sn2 and Co phases have the largest compositional regimes in which alloys display them as the primary solidification phases. There are four class II reactions and four class III reactions. The reactions with the highest and lowest reaction temperatures are both class III reactions, and are L + CoSn2 + Cu6Sn5 = CoSn3 at 621.5 K (348.3 °C) and L + Co3Sn2 + CoSn = Cu6Sn5 at 1157.8 K (884.6 °C), respectively.

Effect of high-intensity ultrasonic irradiation on the modification of solidification microstructure in a Si-rich hypoeutectic Al-Si alloy

Energy Technology Data Exchange (ETDEWEB)

Das, A., E-mail: A.Das@swansea.ac.uk [Materials Research Centre, School of Engineering, Swansea University, Singleton Park, Swansea, SA2 8PP (United Kingdom); Kotadia, H.R. [Brunel Centre for Advanced Solidification Technology, Brunel University, Uxbridge, UB8 3PH (United Kingdom)

2011-02-15

Effect of high-intensity ultrasound irradiation in modifying complex solidification microstructure is explored in a high Si containing Al-Si alloy and the origin of microstructural changes explained on the basis of nucleation and growth behaviour. Complete suppression of dendritic growth and dramatic refinement to globular morphology were observed for primary {alpha}-Al grains. Strong supportive evidence is presented towards enhanced and prolonged heterogeneous nucleation triggered by cavitation induced increase in the equilibrium melting point and effective dissipation of latent heat at the solidification front. Morphological evolution of eutectic Si and intermetallic particles is found to be dominated by coarsening and spherodisation from strong fluid flow in areas of intense cavitation near the ultrasonic radiator. Outside the region of direct energy transfer, Si particle morphology appears to be controlled predominantly by the imposed cooling conditions. Extremely fine and short Si-platelets observed in the intergranular spaces near the radiator are explained on the basis of probable rapid cooling of final liquid pockets of small volume and large surface area, rather than refinement through ultrasound.

Modeling of multiphase flow with solidification and chemical reaction in materials processing

Science.gov (United States)

Wei, Jiuan

on SPH method and macroscopic model based on FVM, FEM and FDM, can be applied to even more complicated system. In the mesoscopic model by SPH method, some fundamental mesoscopic phenomena, such as the microstructure evolution, interface morphology represented by high resolution, particle entrapment in solidification can be studied. In the macroscopic model, the heat transfer, fluid flow, species transport can be modeled, and the simulation results provided the velocity, temperature and species boundary condition necessary for the mesoscopic model. This part falls into the region of future work. (Abstract shortened by UMI.)

Incorporating interfacial phenomena in solidification models

Science.gov (United States)

Beckermann, Christoph; Wang, Chao Yang

1994-01-01

A general methodology is available for the incorporation of microscopic interfacial phenomena in macroscopic solidification models that include diffusion and convection. The method is derived from a formal averaging procedure and a multiphase approach, and relies on the presence of interfacial integrals in the macroscopic transport equations. In a wider engineering context, these techniques are not new, but their application in the analysis and modeling of solidification processes has largely been overlooked. This article describes the techniques and demonstrates their utility in two examples in which microscopic interfacial phenomena are of great importance.

Characterisation of the Interaction between Toroidal Vortex Structures and Flame Front Propagation

International Nuclear Information System (INIS)

Long, E J; Hargrave, G K; Jarvis, S; Justham, T; Halliwell, N

2006-01-01

Experimental laser diagnostic data is presented for flame characterisation during interactions with toroidal vortices generated in the wake of an annular obstacle. A novel twin section combustion chamber has been utilised to allow the controlled formation of stable eddy structures into which a flame front can propagate. High speed laser sheet visualisation was employed to record the flow field and flame front temporal development and high-speed digital particle image velocimetry was used to quantify the velocity field of the unburnt mixture ahead of the flame front. Results provide characterisation of the toroidal vortex/flame front interaction for a range of vortex scales of and recirculation strengths

Characterisation of the Interaction between Toroidal Vortex Structures and Flame Front Propagation

Energy Technology Data Exchange (ETDEWEB)

Long, E J; Hargrave, G K; Jarvis, S; Justham, T; Halliwell, N [Wolfson School of Mechanical and Manufacturing Engineering, Loughborough University, Loughborough, Leicestershire, LE11 3TU (United Kingdom)

2006-07-15

Experimental laser diagnostic data is presented for flame characterisation during interactions with toroidal vortices generated in the wake of an annular obstacle. A novel twin section combustion chamber has been utilised to allow the controlled formation of stable eddy structures into which a flame front can propagate. High speed laser sheet visualisation was employed to record the flow field and flame front temporal development and high-speed digital particle image velocimetry was used to quantify the velocity field of the unburnt mixture ahead of the flame front. Results provide characterisation of the toroidal vortex/flame front interaction for a range of vortex scales of and recirculation strengths.

Characterisation of the Interaction between Toroidal Vortex Structures and Flame Front Propagation

Science.gov (United States)

Long, E. J.; Hargrave, G. K.; Jarvis, S.; Justham, T.; Halliwell, N.

2006-07-01

Experimental laser diagnostic data is presented for flame characterisation during interactions with toroidal vortices generated in the wake of an annular obstacle. A novel twin section combustion chamber has been utilised to allow the controlled formation of stable eddy structures into which a flame front can propagate. High speed laser sheet visualisation was employed to record the flow field and flame front temporal development and high-speed digital particle image velocimetry was used to quantify the velocity field of the unburnt mixture ahead of the flame front. Results provide characterisation of the toroidal vortex/flame front interaction for a range of vortex scales of and recirculation strengths.

Propagation of transition fronts in nonlinear chains with non-degenerate on-site potentials

Science.gov (United States)

Shiroky, I. B.; Gendelman, O. V.

2018-02-01

We address the problem of transition front propagation in chains with a bi-stable nondegenerate on-site potential and a nonlinear gradient coupling. For generic nonlinear coupling, one encounters a special regime of transitions, characterized by extremely narrow fronts, far supersonic velocities of the front propagation, and long waves in the oscillatory tail. This regime can be qualitatively associated with a shock wave. The front propagation can be described with the help of a simple reduced-order model; the latter delivers a kinetic law, which is almost not sensitive to the fine details of the on-site potential. Besides, it is possible to predict all main characteristics of the transition front, including its velocity, as well as the frequency and the amplitude of the oscillatory tail. Numerical results are in good agreement with the analytical predictions. The suggested approach allows one to consider the effects of an external pre-load, the next-nearest-neighbor coupling and the on-site damping. When the damping is moderate, it is possible to consider the shock propagation in the damped chain as a perturbation of the undamped dynamics. This approach yields reasonable predictions. When the damping is high, the transition front enters a completely different asymptotic regime of a subsonic kink. The gradient nonlinearity generically turns negligible, and the propagating front converges to the regime described by a simple exact solution for a continuous model with linear coupling.

Multi-scale Modeling of Dendritic Alloy Solidification

OpenAIRE

Dagner, Johannes

2009-01-01

Solidification of metallic melts is one of the most important processes in material science. The microstructure, which is formed during freezing, determines the mechanical properties of the final product largely. Many physical phenomena influence the solidification process and hence the resulting microstructure. One important parameter is influence of melt flow, which may modify heat and species transport on a large range of length- and time-scales. On the micro-scale, it influences the conce...

On the theory of turbulent flame velocity

OpenAIRE

Bychkov, Vitaly; Akkerman, Vyacheslav; Petchenko, Arkady

2012-01-01

The renormalization ideas of self-similar dynamics of a strongly turbulent flame front are applied to the case of a flame with realistically large thermal expansion of the burning matter. In that case a flame front is corrugated both by external turbulence and the intrinsic flame instability. The analytical formulas for the velocity of flame propagation are obtained. It is demonstrated that the flame instability is of principal importance when the integral turbulent length scale is much large...

Modelling of melting and solidification transport phenomena during hypothetical NPP severe accidents

International Nuclear Information System (INIS)

Sarler, B.

1992-01-01

A physical and mathematical framework to deal with the transport phenomena occuring during melting and solidification of the hypothetical NPP severe accidents is presented. It concentrates on the transient temperature, velocity, and species concentration distributions during such events. The framework is based on the Mixture Continuum Formulation of the components and phases, cast in the boundary-domain integral shape structured by the fundamental solution of the Laplace equation. The formulation could cope with various solid-liquid sub-systems through the inclusion of the specific closure relations. The deduced system of boundary-domain integral equations for conservation of mass, energy, momentum, and species could be solved by the boundary element discrete approximative method. (author) [sl

Steady-state and dynamic models for particle engulfment during solidification

Science.gov (United States)

Tao, Yutao; Yeckel, Andrew; Derby, Jeffrey J.

2016-06-01

Steady-state and dynamic models are developed to study the physical mechanisms that determine the pushing or engulfment of a solid particle at a moving solid-liquid interface. The mathematical model formulation rigorously accounts for energy and momentum conservation, while faithfully representing the interfacial phenomena affecting solidification phase change and particle motion. A numerical solution approach is developed using the Galerkin finite element method and elliptic mesh generation in an arbitrary Lagrangian-Eulerian implementation, thus allowing for a rigorous representation of forces and dynamics previously inaccessible by approaches using analytical approximations. We demonstrate that this model accurately computes the solidification interface shape while simultaneously resolving thin fluid layers around the particle that arise from premelting during particle engulfment. We reinterpret the significance of premelting via the definition an unambiguous critical velocity for engulfment from steady-state analysis and bifurcation theory. We also explore the complicated transient behaviors that underlie the steady states of this system and posit the significance of dynamical behavior on engulfment events for many systems. We critically examine the onset of engulfment by comparing our computational predictions to those obtained using the analytical model of Rempel and Worster [29]. We assert that, while the accurate calculation of van der Waals repulsive forces remains an open issue, the computational model developed here provides a clear benefit over prior models for computing particle drag forces and other phenomena needed for the faithful simulation of particle engulfment.

Polyethylene solidification of low-level wastes

International Nuclear Information System (INIS)

Kalb, P.D.; Colombo, P.

1985-02-01

This topical report describes the results of an investigation on the solidification of low-level radioactive waste in polyethylene. Waste streams selected for this study included those which result from advanced volume reduction technologies (dry evaporator concentrate salts and incinerator ash) and those which remain problematic for solidification using contemporary agents (ion exchange resins). Four types of commercially available low-density polyethylenes were employed which encompass a range of processing and property characteristics. Process development studies were conducted to ascertain optimal process control parameters for successful solidification. Maximum waste loadings were determined for each waste and polyethylene type. Property evaluation testing was performed on laboratory-scale specimens to assess the potential behavior of actual waste forms in a disposal environment. Waste form property tests included water immersion, deformation under compressive load, thermal cycling and radionuclide leaching. Recommended waste loadings of 70 wt % sodium sulfate, 50 wt % boric acid, 40 wt % incinerator ash, and 30 wt % ion exchange resins, which are based on process control and waste form performance considerations are reported. 37 refs., 33 figs., 22 tabs

Statistical analysis of turbulent front propagation in the scrape-off-layer

International Nuclear Information System (INIS)

Ghendrih, Ph.; Sarazin, Y.; Attuel, G.; Benkadda, S.; Beyer, P.; Darmet, G.; Falchetto, G.; Figarella, C.; Garbet, X.; Grandgirard, V.; Ottaviani, M.

2005-01-01

The intermittent transport in the SOL is analysed in terms of the interaction between the average profile and the population of large transport events, the fronts. This provides the basis for the statistical analysis presented in this paper. Data from 2D numerical simulations is analysed here. The mean density e-folding length for the fronts is observed to be the same as that of the time average profile. The mean ballistic velocity of the fronts has a radial Mach number of 0.03. A symmetric distribution of poloidal Mach numbers is found, its width is comparable to that of the radial Mach number, ΔM ∼ 0.02. The small fronts are found to be isotropic, the larger fronts are elongated radially (aspect ratio ∼ 6). A characteristic poloidal scale is found, typically 7 Larmor radii

Ultrasonic Acoustic Velocities During Partial Melting of a Mantle Peridotite KLB-1

Science.gov (United States)

Weidner, Donald J.; Li, Li; Whitaker, Matthew L.; Triplett, Richard

2018-02-01

Knowledge of the elastic properties of partially molten rocks is crucial for understanding low-velocity regions in the interior of the Earth. Models of fluid and solid mixtures have demonstrated that significant decreases in seismic velocity are possible with small amounts of melt, but there is very little available data for testing these models, particularly with both P and S waves for mantle compositions. We report ultrasonic measurements of P and S velocities on a partially molten KLB-1 sample at mantle conditions using a multi-anvil device at a synchrotron facility. The P, S, and bulk sound velocities decrease as melting occurs. We find that the quantity, ∂lnVS/∂lnVB (where VB is the bulk sound velocity) is lower than mechanical models estimate. Instead, our data, as well as previous data in the literature, are consistent with a dynamic melting model in which melting and solidification interact with the stress field of the acoustic wave.

Implementation of a gust front head collapse scheme in the WRF numerical model

Science.gov (United States)

Lompar, Miloš; Ćurić, Mladjen; Romanic, Djordje

2018-05-01

Gust fronts are thunderstorm-related phenomena usually associated with severe winds which are of great importance in theoretical meteorology, weather forecasting, cloud dynamics and precipitation, and wind engineering. An important feature of gust fronts demonstrated through both theoretical and observational studies is the periodic collapse and rebuild of the gust front head. This cyclic behavior of gust fronts results in periodic forcing of vertical velocity ahead of the parent thunderstorm, which consequently influences the storm dynamics and microphysics. This paper introduces the first gust front pulsation parameterization scheme in the WRF-ARW model (Weather Research and Forecasting-Advanced Research WRF). The influence of this new scheme on model performances is tested through investigation of the characteristics of an idealized supercell cumulonimbus cloud, as well as studying a real case of thunderstorms above the United Arab Emirates. In the ideal case, WRF with the gust front scheme produced more precipitation and showed different time evolution of mixing ratios of cloud water and rain, whereas the mixing ratios of ice and graupel are almost unchanged when compared to the default WRF run without the parameterization of gust front pulsation. The included parameterization did not disturb the general characteristics of thunderstorm cloud, such as the location of updraft and downdrafts, and the overall shape of the cloud. New cloud cells in front of the parent thunderstorm are also evident in both ideal and real cases due to the included forcing of vertical velocity caused by the periodic collapse of the gust front head. Despite some differences between the two WRF simulations and satellite observations, the inclusion of the gust front parameterization scheme produced more cumuliform clouds and seem to match better with real observations. Both WRF simulations gave poor results when it comes to matching the maximum composite radar reflectivity from radar

Weld solidification cracking in 304 to 304L stainless steel

Energy Technology Data Exchange (ETDEWEB)

Hochanadel, Patrick W [Los Alamos National Laboratory; Lienert, Thomas J [Los Alamos National Laboratory; Martinez, Jesse N [Los Alamos National Laboratory; Martinez, Raymond J [Los Alamos National Laboratory; Johnson, Matthew Q [Los Alamos National Laboratory

2010-01-01

A series of annulus welds were made between 304 and 304L stainless steel coaxial tubes using both pulsed laser beam welding (LBW) and pulsed gas tungsten arc welding (GTAW). In this application, a change in process from pulsed LBW to pulsed gas tungsten arc welding was proposed to limit the possibility of weld solidification cracking since weldability diagrams developed for GTAW display a greater range of compositions that are not crack susceptible relative to those developed for pulsed LBW. Contrary to the predictions of the GTAW weldability diagram, cracking was found. This result was rationalized in terms of the more rapid solidification rate of the pulsed gas tungsten arc welds. In addition, for the pulsed LBW conditions, the material compositions were predicted to be, by themselves, 'weldable' according to the pulsed LBW weldability diagram. However, the composition range along the tie line connecting the two compositions passed through the crack susceptible range. Microstructurally, the primary solidification mode (PSM) of the material processed with higher power LBW was determined to be austenite (A), while solidification mode of the materials processed with lower power LBW apparently exhibited a dual PSM of both austenite (A) and ferrite-austenite (FA) within the same weld. The materials processed by pulsed GT A W showed mostly primary austenite solidification, with some regions of either primary austenite-second phase ferrite (AF) solidification or primary ferrite-second phase austenite (FA) solidification. This work demonstrates that variations in crack susceptibility may be realized when welding different heats of 'weldable' materials together, and that slight variations in processing can also contribute to crack susceptibility.

Weld solidification cracking in 304 to 204L stainless steel

Energy Technology Data Exchange (ETDEWEB)

Hochanadel, Patrick W [Los Alamos National Laboratory; Lienert, Thomas J [Los Alamos National Laboratory; Martinez, Jesse N [Los Alamos National Laboratory; Johnson, Matthew Q [Los Alamos National Laboratory

2010-09-15

A series of annulus welds were made between 304 and 304L stainless steel coaxial tubes using both pulsed laser beam welding (LBW) and pulsed gas tungsten arc welding (GTAW). In this application, a change in process from pulsed LBW to pulsed gas tungsten arc welding was proposed to limit the possibility of weld solidification cracking since weldability diagrams developed for GTAW display a greater range of compositions that are not crack susceptible relative to those developed for pulsed LBW. Contrary to the predictions of the GTAW weldability diagram, cracking was found.This result was rationalized in terms of the more rapid solidification rate of the pulsed gas tungsten arc welds. In addition, for the pulsed LBW conditions, the material compositions were predicted to be, by themselves, 'weldable' according to the pulsed LBW weldability diagram. However, the composition range along the tie line connecting the two compositions passed through the crack susceptible range. Microstructurally, the primary solidification mode (PSM) of the material processed with higher power LBW was determined to be austenite (A), while solidification mode of the materials processed with lower power LBW apparently exhibited a dual PSM of both austenite (A) and ferrite-austenite (FA) within the same weld. The materials processed by pulsed GTAW showed mostly primary austenite solidification, with some regions of either primary austenite-second phase ferrite (AF) solidification or primary ferrite-second phase austenite (FA) solidification. This work demonstrates that variations in crack susceptibility may be realized when welding different heats of 'weldable' materials together, and that slight variations in processing can also contribute to crack susceptibility.

Multijam Solutions in Traffic Models with Velocity-Dependent Driver Strategies

DEFF Research Database (Denmark)

Carter, Paul; Christiansen, Peter Leth; Gaididei, Yuri B.

2014-01-01

The optimal-velocity follow-the-leader model is augmented with an equation that allows each driver to adjust their target headway according to the velocity difference between the driver and the car in front. In this more detailed model, which is investigated on a ring, stable and unstable multipu...

Rate of solidification of aluminium casting in varying wall thickness of cylindrical metallic moulds

Directory of Open Access Journals (Sweden)

Katsina Christopher BALA

2014-02-01

Full Text Available The quality of final casting mainly depends on the rate of solidification as rapid solidification produces fine grains structures with better mechanical properties. The analysis of heat transfer during the casting and solidification of aluminium alloy as well as the experimental investigation of the rate of solidification in varying thicknesses of cylindrical metallic mould was carried out. The temperature variation with time of the casting was recorded from which cooling curves were obtained for the determination of solidification time of the cast. The results showed that as the cylindrical mould thickness increases the solidification time decreases due to the chilling effect of the mould.

Detonation velocity in poorly mixed gas mixtures

Science.gov (United States)

Prokhorov, E. S.

2017-10-01

The technique for computation of the average velocity of plane detonation wave front in poorly mixed mixture of gaseous hydrocarbon fuel and oxygen is proposed. Here it is assumed that along the direction of detonation propagation the chemical composition of the mixture has periodic fluctuations caused, for example, by layered stratification of gas charge. The technique is based on the analysis of functional dependence of ideal (Chapman-Jouget) detonation velocity on mole fraction (with respect to molar concentration) of the fuel. It is shown that the average velocity of detonation can be significantly (by more than 10%) less than the velocity of ideal detonation. The dependence that permits to estimate the degree of mixing of gas mixture basing on the measurements of average detonation velocity is established.

Kinetics of a plasma streamer ionization front

Science.gov (United States)

Taccogna, Francesco; Pellegrini, Fabrizio

2018-02-01

A streamer is a non-linear and non-local gas breakdown mode. Its large-scale coherent structures, such as the ionization front, are the final results of a hierarchical cascade starting from the single particle dynamics. Therefore, this phenomenon covers, by definition, different space and time scales. In this study, we have reproduced the ionization front formation and development by means of a particle-based numerical methodology. The physical system investigated concerns of a high-voltage ns-pulsed surface dielectric barrier discharge. Different reduced electric field regimes ranging from 50 to 500 Td have been considered for two gases: pure atomic Ar and molecular N2. Results have shown the detailed structure of the negative streamer: the leading edge, the head, the interior and the tail. Its dynamical evolution and the front propagation velocity have been calculated for the different cases. Finally, the deviation of the electron energy distribution function from equilibrium behavior has been pointed out as a result of a fast and very localized phenomenon.

Dynamics of quench front during emergency cooling of PWR core after LOCA accident

International Nuclear Information System (INIS)

Osmachkin, V.S.

2000-01-01

A review of some analytical results for assessment of quenches velocity is presented. Attention is paid to the influence on front velocity due to the peculiarities of fuel, gas gap and fuel pellets as well due to the decay heat and renewed heat-up coming from the cladding oxidation during reflooding. (author)

Defect generation during solidification of aluminium foams

International Nuclear Information System (INIS)

Mukherjee, M.; Garcia-Moreno, F.; Banhart, J.

2010-01-01

The reason for the frequent occurrence of cell wall defects in metal foams was investigated. Aluminium foams often expand during solidification, a process which is referred as solidification expansion (SE). The effect of SE on the structure of aluminium foams was studied in situ by X-ray radioscopy and ex situ by X-ray tomography. A direct correlation between the magnitude of SE and the number of cell wall ruptures during SE and finally the number of defects in the solidified foams was found.

Plastic solidification system for radioactive waste

International Nuclear Information System (INIS)

Kani, Jiro; Irie, Hiromitsu; Obu, Etsuji; Nakayama, Yasuyuki; Matsuura, Hiroyuki.

1979-01-01

The establishment of a new solidification system is an important theme for recent radioactive-waste disposal systems. The conditions required of new systems are: (1) the volume of the solidified product to be reduced, and (2) the property of the solidified product to be superior to the conventional ones. In the plastic solidification system developed by Toshiba, the waste is first dried and then solidified with thermosetting resin. It has been confirmed that the property of the plastic solidified product is superior to that of the cement-or bitumen-solidified product. Investigation from various phases is being carried on for the application of this method to commercial plants. (author)

Multiple reinjections and crystal mush compaction in the solidification evolution of the Karaj Dam basement Sill, Northern Iran

Science.gov (United States)

Maghdour-Mashhour, Reza; Shabani, Amir Ali Tabbakh

2017-07-01

The Karaj Dam basement Sill is a 460 m-thick saucer shaped sill, situated in the Alborz Magmatic Belt, Northern Iran. The results of geochemical, textural and field relations reveal characteristics of a sill with a well-developed S-shaped compositional profile which could be subdivided into distinct parts and suggest that the sill was repeatedly split and reinjected with fresh magma in the upper half of the previous emplacements (over- to partly intra-accretion). Whole rock and mineral compositional profiles have recorded five to six discrete injections of magma, each of which individually show an upward increase in terms of primitivity which represents partial crystallization in feeder conduits. The first three small successive pulses of magma, emplaced in the basal 150 m of the floor sequence, were followed by voluminous fourth and fifth pulses in the upper portion of the sill. During final two pulses the system acts as a closed system for each independently, and evolves through compositional convection or compaction aided in-situ crystallization. Theoretical models for convection and compaction shows the significance of both processes. Considering the final porosity of 0.1 rate of the basal 150 m and upper portion of the sill (Va = 1 and 0.1 m/year), when the crystal mush varies between 1 to 0.01 m with the liquid viscosity ranging from 85 to 15 Pa·s. Our calculations further indicate that compaction driven velocity of liquid expulsion (ω - w) hardly exceeds the Va in the basal 150 m of the floor sequence. The highest velocity is reached (ω - w = 1 m/year) only if the crystal mush thickness is no less than 240 m with the porosity of 0.6 and the liquid viscosity of no more than 15 Pa·s. On the other hand, compaction is highly effective in the upper portion of the sill. Transfer of residual liquid from the compacting lower solidification front to the dilating upper solidification front resulted in characteristic chemical and mineralogical effects, such as the

Solidification technique of radioactive elements. Research using zirconium phosphates

International Nuclear Information System (INIS)

Nakayama, Susumu; Ito, Katsuhiko

2005-01-01

Proton type zirconium phosphates HZr 2 (PO 4 ) 3 , NASICON type three-dimensional net work structure, is used for solidification of Cs in the high level radioactive waste. Two kinds of solidification methods such as the dry method and autoclave method are explained. Cs ion entered into 0.6nm space of HZr 2 (PO 4 ) 3 , and formed ionic bonding, which made the difficult situation to remove. When mixture of HZr 2 (PO 4 ) 3 and 23 kinds of M(NO 3 )n (M= Li, Na, K, Pb, Sr, Bi, Y, Mg, Ca, Sc, Mn, Fe, Co, Ni, Cu, Zn, Ag, Cd, Ba, La, Ce, Tl, and Pb; n=1,2 or 3) was treated at 400-700degC by dry method, solidification of the subject metals was succeeded. Amount of solidification of Cs by autoclave at 250degC is almost same as the dry method and its leachability resistance increased 40 times than that of dry method after heat treatment in atmosphere at 700degC. (S.Y.)

A dendritic solidification experiment under large gravity - implications for the Earth's inner core solidification regime.

Science.gov (United States)

Deguen, R.; Alboussière, T.; Brito, D.; La Rizza, P.; Masson, J.

2009-05-01

The Earth's inner core solidification regime is usually thought to be dendritic, which should results in the formation of a mushy layer at the inner core boundary, possibly extending deep in the inner core. The release of latent heat and solute associated with crystallization provides an important boyancy source to drive thermo- chemical convection in the core. In the laboratory, two modes of convection associated with the crystallization of mushy layers have been observed. One is a boundary layer mode originating from the destabilisation of the chemical boundary layer present at the mush-liquid interface; the second is the so-called 'mushy layer mode' which involves the whole mushy layer. In the mushy layer mode, convection usually takes the form of narrow plumes rising through crystal free conduits called chimneys. One particularity of inner core crystallization is its extremely small solidification rate compared to typical outer core convective timescales. We have designed and build an experiment devoted to the study of crystallization under a large gravity field, using a centrifuge, of an aqueous solution of ammonium chloride, which is a good analogue to metallic alloys. The large gravity field allows to reach Rayleigh numbers much larger than in typical solidification experiments. Under large gravity fields, we observe the disappearance of chimney convection and show that the large gravity field promotes the boundary layer convection mode at the expent of the mushy layer mode. As the gravitationnal forcing is increased, convective heat and solute transport are significantly enhanced, which results in larger solid fraction directly below the mush-liquid interface. The increase in solid fraction results in a dramatic decrease of the permeability in the mushy layer, which eventually becomes subcritical in respect to the mushy layer mode. Because of the very slow solidification rate of the inner core, convective transport of heat and solute from the ICB is

Matemathical description of solidification cooling curves of pure metals

Directory of Open Access Journals (Sweden)

Arno Müller

1998-10-01

Full Text Available The introduction of an "incubation time" to the Schwarz classical mathematical description of metals solidification, resulted in a new model called Modified Schwarz Model. By doing so it was possible to identify and quantify the "delay time" that separates the two heat waves traveling independently in a casting during the solidification: the Supercooled / Superheated Liquid and the Solid / Liquid. The thermal shock produced in the initial stage of the undercooling generation process, can be used as an important parameter in the forecasting of the solidification's behavior of pure metals and alloys, when changing mold's materials, pouring and ambient temperatures. The hypercooling proneness degree of metals and alloys, can also be calculated.

Chemical consequences of compaction within the freezing front of a crystallizing magma ocean

Science.gov (United States)

Hier-Majumder, S.; Hirschmann, M. M.

2013-12-01

The thermal and compositional evolution of planetary magma oceans have profound influences on the early development and differentiation of terrestrial planets. During crystallization, rejection of elements incompatible in precipitating solids leads to petrologic and geochemical planetary differentiation, including potentially development of a compositionally stratified early mantle and evolution of thick overlying atmospheres. In cases of extremely efficient segregation of melt and crystals, solidified early mantles can be nearly devoid of key incompatible species including heat-producing (U, Th, K) and volatile (H,C,N,& noble gas) elements. A key structural component of a crystallizing magma ocean is the partially molten freezing front. The dynamics of this region influences the distribution of incompatible elements between the earliest mantle and the initial surficial reservoirs. It also can be the locus of heating owing to the dissipation of large amounts of tidal energy potentially available from the early Moon. The dynamics are influenced by the solidification rate, which is coupled to the liberation of volatiles owing to the modulating greenhouse effects in the overlying thick atmosphere. Compaction and melt retention in the freezing front of a magma ocean has received little previous attention. While the front advances during the course of crystallization, coupled conservation of mass, momentum, and energy within the front controls distribution and retention of melt within this layer. Due to compaction within this layer, melt distribution is far from uniform, and the fraction of melt trapped within this front depends on the rate of freezing of the magma ocean. During phases of rapid freezing, high amount of trapped melt within the freezing front retains a larger quantity of dissolved volatiles and the reverse is true during slow periods of crystallization. Similar effects are known from inferred trapped liquid fractions in layered mafic intrusions. Here we

Formation of intrathermocline eddies at ocean fronts by wind-driven destruction of potential vorticity

Science.gov (United States)

Thomas, Leif N.

2008-08-01

A mechanism for the generation of intrathermocline eddies (ITEs) at wind-forced fronts is examined using a high resolution numerical simulation. Favorable conditions for ITE formation result at fronts forced by "down-front" winds, i.e. winds blowing in the direction of the frontal jet. Down-front winds exert frictional forces that reduce the potential vorticity (PV) within the surface boundary in the frontal outcrop, providing a source for the low-PV water that is the materia prima of ITEs. Meandering of the front drives vertical motions that subduct the low-PV water into the pycnocline, pooling it into the coherent anticyclonic vortex of a submesoscale ITE. As the fluid is subducted along the outcropping frontal isopycnal, the low-PV water, which at the surface is associated with strongly baroclinic flow, re-expresses itself as water with nearly zero absolute vorticity. This generation of strong anticyclonic vorticity results from the tilting of the horizontal vorticity of the frontal jet, not from vortex squashing. During the formation of the ITE, high-PV water from the pycnocline is upwelled alongside the subducting low-PV surface water. The positive correlation between the ITE's velocity and PV fields results in an upward, along-isopycnal eddy PV flux that scales with the surface frictional PV flux driven by the wind. The relationship between the eddy and wind-induced frictional PV flux is nonlocal in time, as the eddy PV flux persists long after the wind forcing is shut off. The ITE's PV flux affects the large-scale flow by driving an eddy-induced transport or bolus velocity down the outcropping isopycnal layer with a magnitude that scales with the Ekman velocity.

Remote sensing of coastal fronts and their effects on oil dispersion

Energy Technology Data Exchange (ETDEWEB)

Klemas, V

1980-01-01

The use of remote sensing techniques to determine the properties of coastal and estuarine fronts, which represent regions of discontinuities and high gradients in ocean physical parameters such as velocity and density, and to assess the influence of such fronts on oil pollutants is discussed. Results of an aircraft and boat verification study of an oil drift and spread model in Delaware Bay are indicated which illustrate the tendency of oil slicks to be attracted to frontal regions, where a denser fluid underlies a lighter fluid giving rise to an inclined interface with convergence zones. Landsat imagery of the bay acquired in order to incorporate frontal information into the interactive computer model is then presented which allows the locations of coastal fronts to be charted throughout a tidal cycle. It is noted that satellite observations of flood-associated fronts on the New Jersey side of the bay and ebb-associated fronts on the Delaware side agree with boat measurements and model predictions, and that the remote tracking of fronts by aircraft and satellites will aid in oil slick clean-up operations.

Inverse thermal analysis method to study solidification in cast iron

DEFF Research Database (Denmark)

Dioszegi, Atilla; Hattel, Jesper

2004-01-01

Solidification modelling of cast metals is widely used to predict final properties in cast components. Accurate models necessitate good knowledge of the solidification behaviour. The present study includes a re-examination of the Fourier thermal analysis method. This involves an inverse numerical...... solution of a 1-dimensional heat transfer problem connected to solidification of cast alloys. In the analysis, the relation between the thermal state and the fraction solid of the metal is evaluated by a numerical method. This method contains an iteration algorithm controlled by an under relaxation term...... inverse thermal analysis was tested on both experimental and simulated data....

Choosing solidification or vitrification for low-level radioactive and mixed waste treatment

International Nuclear Information System (INIS)

Gimpel, R.F.

1992-01-01

Solidification (making concrete) and vitrification (making glass) are frequently the treatment methods recommended for treating inorganic or radioactive wastes. Solidification is generally perceived as the most economical treatment method. Whereas, vitrification is considered (by many) as the most effective of all treatment methods. Unfortunately, vitrification has acquired the stigma that it is too expensive to receive further consideration as an alternative to solidification in high volume treatment applications. Ironically, economic studies, as presented in this paper, show that vitrification may be more competitive in some high volume applications. Ex-situ solidification and vitrification are the competing methods for treating in excess of 450 000m 3 of low-level radioactive and mixed waste at the Fernald Environmental Management Project (FEMP or simply, Fernald) located near Cincinnati, Ohio. This paper summarizes how Fernald is choosing between solidification and vitrification as the primary waste treatment method

Choosing solidification or vitrification for low-level radioactive and mixed waste treatment

International Nuclear Information System (INIS)

Gimpel, R.F.

1992-01-01

Solidification (making concrete) and vitrification (making glass) are frequently the treatment methods recommended for treating inorganic or radioactive wastes. Solidification is generally perceived as the most economical treatment method. Whereas, vitrification is considered (by many) as the most effective of all treatment methods. Unfortunately, vitrification has acquired the stigma that it is too expensive to receive further consideration as an alternative to solidification in high volume treatment applications. Ironically, economic studies, as presented in this paper, show that vitrification may be more competitive in some high volume applications. Ex-situ solidification and vitrification are the competing methods for treating in excess of 450,000 m 3 of low-level radioactive and mixed waste at the Fernald Environmental Management Project (FEMP or simply, Fernald) located near Cincinnati, Ohio. This paper summarized how Fernald is choosing between solidification and vitrification as the primary waste treatment method

Development of sodium disposal technology. Experiment of sodium compound solidification process

International Nuclear Information System (INIS)

Matsumoto, Toshiyuki; Ohura, Masato; Yatoh, Yasuo

2007-07-01

A large amount of sodium containing radioactive waste will come up at the time of final shutdown/decommission of FBR plant. The radioactive waste is managed as solid state material in a closed can in Japan. As for the sodium, there is no established method to convert the radioactive sodium to solid waste. Further, the sodium is highly reactive. Thus, it is recommended to convert the sodium to a stable substance before the solidification process. One of the stabilizing methods is conversion of sodium into sodium hydroxide solution. These stabilization and solidification processes should be safe, economical, and efficient. In order to develop such sodium disposal technology, nonradioactive sodium was used and a basic experiment was performed. Waste-fluid Slag Solidification method was employed as the solidification process of sodium hydroxide solution. Experimental parameters were mixing ratio of the sodium hydroxide and the slag solidification material, temperature and concentration of the sodium hydroxide. The best parameters were obtained to achieve the maximum filling ratio of the sodium hydroxide under a condition of enough high compressive strength of the solidified waste. In a beaker level test, the solidified waste was kept in a long term and it was shown that there was no change of appearance, density, and also the compressive strength was kept at a target value. In a real scale test, homogeneous profiles of the density and the compressive strength were obtained. The compressive strength was higher than the target value. It was shown that the Waste-fluid Slag Solidification method can be applied to the solidification process of the sodium hydroxide solution, which was produced by the stabilization process. (author)

Characterizing Ion Flows Across a Dipolarization Front

Science.gov (United States)

Arnold, H.; Drake, J. F.; Swisdak, M.

2017-12-01

In light of the Magnetospheric Multiscale Mission (MMS) moving to study predominately symmetric magnetic reconnection in the Earth's magnetotail, it is of interest to investigate various methods for determining the relative location of the satellites with respect to the x line or a dipolarization front. We use a 2.5 dimensional PIC simulation to explore the dependence of various characteristics of a front, or flux bundle, on the width of the front in the dawn-dusk direction. In particular, we characterize the ion flow in the x-GSM direction across the front. We find a linear relationship between the width of a front, w, and the maximum velocity of the ion flow in the x-GSM direction, Vxi, for small widths: Vxi/VA=w/di*1/2*(mVA2)/Ti*Bz/Bxwhere m, VA, di, Ti, Bz, and Bx are the ion mass, upstream Alfven speed, ion inertial length, ion temperature, and magnetic fields in the z-GSM and x-GSM directions respectively. However, once the width reaches around 5 di, the relationship gradually approaches the well-known theoretical limit for ion flows, the upstream Alfven speed. Furthermore, we note that there is a reversal in the Hall magnetic field near the current sheet on the positive y-GSM side of the front. This reversal is most likely due to conservation of momentum in the y-GSM direction as the ions accelerate towards the x-GSM direction. This indicates that while the ions are primarily energized in the x-GSM direction by the front, they transfer energy to the electromagnetic fields in the y-GSM direction. The former energy transfer is greater than the latter, but the reversal of the Hall magnetic field drags the frozen-in electrons along with it outside of the front. These simulations should better able researchers to determine the relative location of a satellite crossing a dipolarization front.

Macrosegregation Resulting from Directional Solidification Through an Abrupt Change in Cross-Sections

Science.gov (United States)

Lauer, M.; Poirier, D. R.; Ghods, M.; Tewari, S. N.; Grugel, R. N.

2017-01-01

Simulations of the directional solidification of two hypoeutectic alloys (Al-7Si alloy and Al-19Cu) and resulting macrosegregation patterns are presented. The casting geometries include abrupt changes in cross-section from a larger width of 9.5 mm to a narrower 3.2 mm width then through an expansion back to a width of 9.5 mm. The alloys were chosen as model alloys because they have similar solidification shrinkages, but the effect of Cu on changing the density of the liquid alloy is about an order of magnitude greater than that of Si. The simulations compare well with experimental castings that were directionally solidified in a graphite mold in a Bridgman furnace. In addition to the simulations of the directional solidification in graphite molds, some simulations were effected for solidification in an alumina mold. This study showed that the mold must be included in numerical simulations of directional solidification because of its effect on the temperature field and solidification. For the model alloys used for the study, the simulations clearly show the interaction of the convection field with the solidifying alloys to produce a macrosegregation pattern known as "steepling" in sections with a uniform width. Details of the complex convection- and segregation-patterns at both the contraction and expansion of the cross-sectional area are revealed by the computer simulations. The convection and solidification through the expansions suggest a possible mechanism for the formation of stray grains. The computer simulations and the experimental castings have been part of on-going ground-based research with the goal of providing necessary background for eventual experiments aboard the ISS. For casting practitioners, the results of the simulations demonstrate that computer simulations should be applied to reveal interactions between alloy solidification properties, solidification conditions, and mold geometries on macrosegregation. The simulations also presents the

Solidification of ash from incineration of low-level radioactive waste

International Nuclear Information System (INIS)

Roberson, W.A.; Albenesius, E.L.; Becker, G.W.

1983-01-01

The safe disposal of both high-level and low-level radioactive waste is a problem of increasing national attention. A full-scale incineration and solidification process to dispose of suspect-level and low-level beta-gamma contaminated combustible waste is being demonstrated at the Savannah River Plant (SRP) and Savannah River Laboratory (SRL). The stabilized wasteform generated by the process will meet or exceed all future anticipated requirements for improved disposal of low-level waste. The incineration process has been evaluated at SRL using nonradioactive wastes, and is presently being started up in SRP to process suspect-level radioactive wastes. A cement solidification process for incineration products is currently being evaluated by SRL, and will be included with the incineration process in SRP during the winter of 1984. The GEM alumnus author conducted research in a related disposal solidification program during the GEM-sponsored summer internship, and upon completion of the Masters program, received full-time responsibility for developing the incineration products solidification process

Toxic and hazardous waste disposal. Volume 1. Processes for stabilization/solidification

International Nuclear Information System (INIS)

Pojasek, R.B.

1979-01-01

Processes for the stabilization and/or solidification of toxic, hazardous, and radioactive wastes are reviewed. The types of wastes classified as hazardous are defined. The following processes for the solidification of hazardous wastes are described: lime-based techniques; thermoplastic techniques; organic polymer techniques; and encapsulation. The following processes for the solidification of high-level radioactive wastes are described: calcination; glassification; and ceramics. The solidification of low-level radioactive wastes with asphalt, cement, and polymeric materials is also discussed. Other topics covered include: the use of an extruder/evaporator to stabilize and solidify hazardous wastes; effect disposal of fine coal refuse and flue gas desulfurization slurries using Calcilox additive stabilization; the Terra-Tite Process; the Petrifix Process; the SFT Terra-Crete Process; Sealosafe Process; Chemfix Process; and options for disposal of sulfur oxide wastes

An analytical model for displacement velocity of liquid film on a hot vertical surface

International Nuclear Information System (INIS)

Yoshioka, Keisuke; Hasegawa, Shu

1975-01-01

The downward progress of the advancing front of a liquid film streaming down a heated vertical surface, as it would occur in emergency core cooling, is much slower than in the case of ordinary streaming down along a heated surface already wetted with the liquid. A two-dimensional heat conduction model is developed for evaluating this velocity of the liquid front, which takes account of the heat removal by ordinary flow boiling mechanism. In the analysis, the maximum heat flux and the calefaction temperature are taken up as parameters in addition to the initial dry heated wall temperature, the flow rate and the velocity of downward progress of the liquid front. The temperature profile is calculated for various combinations of these parameters. Two criteria are proposed for choosing the most suitable combination of the parameters. One is to reject solutions that represent an oscillating wall temperature distribution, and the second criterion requires that the length of the zone of violent boiling immediately following the liquid front should not be longer than about 1 mm, this value being determined from comparisons made between experiment and calculation. Application of the above two criteria resulted in reasonable values obtained for the calefaction temperature and the maximum heat flux, and the velocity of the liquid front derived therefrom showed good agreement with experiment. (auth.)

Effects Disposal Condition and Ground Water to Leaching Rate of Radionuclides from Solidification Products

International Nuclear Information System (INIS)

Herlan Martono; Wati

2008-01-01

Effects disposal condition and ground water to leaching rate of radionuclides from solidification products have been studied. The aims of leaching test at laboratory to get the best composition of solidified products for continuous process or handling. The leaching rate of radionuclides from the many kinds of matrix from smallest to bigger are glass, thermosetting plastic, urea formaldehyde, asphalt, and cement. Glass for solidification of high level waste, thermosetting plastic and urea formaldehyde for solidification of low and intermediate waste, asphalt and cement for solidification of low and intermediate level waste. In shallow land burial, ground water rate is fast, debit is high, and high permeability, so the probability contact between solidification products and ground water is occur. The pH of ground water increasing leaching rate, but cation in the ground water retard leaching rate. Effects temperature radiation and radiolysis to solidification products is not occur. In the deep repository, ground water rate is slow, debit is small, and low permeability, so the probability contact between solidification products and ground water is very small. There are effect cooling time and distance between pits to rock temperature. Alfa radiation effects can be occur, but there is no contact between solidification products and ground water, so that there is not radiolysis. (author)

Effect of chemical composition and cooling conditions on solidification hot cracking of Ni-based alloys

International Nuclear Information System (INIS)

De Vito, Sophie

2000-01-01

Ni-based alloys 690 present solidification hot cracks during welding of vapour generators. Hot cracks are qualitatively known to be due to the formation of inter-dendritic liquid films and of secondary phases down to low temperatures. This study aims at establishing the link between thermodynamics, solidification and hot cracking. Experimental solidification paths of high purity alloys (with varying Nb and Si contents) are obtained from quenching during directional solidification and TIG-welding experiments. They are compared to Thermo-Calc computations, assuming no diffusion in the solid. From directional solidification samples, good agreement between computed and experimental solidification paths is shown in the quenched liquid. Secondary arms of dendrites are affected by solid state diffusion of Nb. Combined effect of diffusion and solute build-up in the liquid phase modifies micro-segregation in the solid region. Solidification paths from welding specimens are similar to those of the solid region of quenched samples. Nb solid state diffusion is negligible but undercooling compensates the effect of solid state diffusion in directional solidification. Evolution of liquid fraction at the end of the solidification is in accordance with the hot cracking classification of the alloys. Nb favours formation of inter-dendritic liquid films and eutectic-like phases down to low temperature. (author) [fr

Beam-front dynamics and ion acceleration in drifting intense relativistic electron beams

International Nuclear Information System (INIS)

Alexander, K.F.; Hintze, W.

1976-01-01

Collective ion acceleration at the injection of a relativistic electron beam into a low-pressure gas or a plasma is discussed and its strong dependence on the beam-front dynamics is shown. A simple one-dimensional model taking explicitly into account the motion and ionizing action of the ions in the beam-front region is developed for the calculation of the beam drift velocity. The obtained pressure dependence is in good agreement with experimental data. The energy distribution is shown of the ions accelerated in the moving potential well of the space charge region. Scaling laws for the beam-front dynamics and ion acceleration are derived. (J.U.)

Study of the thermal and kinetic parameters during directional solidification of zinc-aluminum eutectic alloys

International Nuclear Information System (INIS)

Gueijman, Sergio Fabian; Ares, Alicia Esther; Schvezov, Carlos Enrique

2008-01-01

Much work has been done recently on investigating zinc-based binary alloys, with different aluminum content, and modified or not with small amounts of other alloying elements. Some of these alloys have interesting properties, such as, the ZA alloys that have properties similar to some bronzes that are used in applications that require pieces with enough resistance to mechanical stresses. The longitudinal thermal gradients, the minimal gradients, the velocities of the liquid interphases, the velocities of the solid interphases and the accelerations of both interphases as a function of time and position were determined for each diluted alloy of the eutectic concentration considered (Zn-5%Al, % in weight), solidified horizontally with caloric extraction from both ends of the test pieces. The values obtained from the horizontal solidification with two directions of predominant caloric extraction are compared to previous values obtained for the same vertically solidified alloy system with a predominantly caloric extraction direction

Nuclear waste solidification

Science.gov (United States)

Bjorklund, William J.

1977-01-01

High level liquid waste solidification is achieved on a continuous basis by atomizing the liquid waste and introducing the atomized liquid waste into a reaction chamber including a fluidized, heated inert bed to effect calcination of the atomized waste and removal of the calcined waste by overflow removal and by attrition and elutriation from the reaction chamber, and feeding additional inert bed particles to the fluidized bed to maintain the inert bed composition.

Nuclear waste solidification

International Nuclear Information System (INIS)

Bjorklund, W.J.

1977-01-01

High level liquid waste solidification is achieved on a continuous basis by atomizing the liquid waste and introducing the atomized liquid waste into a reaction chamber including a fluidized, heated inert bed to effect calcination of the atomized waste and removal of the calcined waste by overflow removal and by attrition and elutriation from the reaction chamber, and feeding additional inert bed particles to the fluidized bed to maintain the inert bed composition

Finite-element solidification modelling of metals and binary alloys

International Nuclear Information System (INIS)

Mathew, P.M.

1986-12-01

In the Canadian Nuclear Fuel Waste Management Program, cast metals and alloys are being evaluated for their ability to support a metallic fuel waste container shell under disposal vault conditions and to determine their performance as an additional barrier to radionuclide release. These materials would be cast to fill residual free space inside the container and allowed to solidify without major voids. To model their solidification characteristics following casting, a finite-element model, FAXMOD-3, was adopted. Input parameters were modified to account for the latent heat of fusion of the metals and alloys considered. This report describes the development of the solidification model and its theoretical verification. To model the solidification of pure metals and alloys that melt at a distinct temperature, the latent heat of fusion was incorporated as a double-ramp function in the specific heat-temperature relationship, within an interval of +- 1 K around the solidification temperature. Comparison of calculated results for lead, tin and lead-tin eutectic melts, unidirectionally cooled with and without superheat, showed good agreement with an alternative technique called the integral profile method. To model the solidification of alloys that melt over a temperature interval, the fraction of solid in the solid-liquid region, as calculated from the Scheil equation, was used to determine the fraction of latent heat to be liberated over a temperature interval within the solid-liquid zone. Comparison of calculated results for unidirectionally cooled aluminum-4 wt.% copper melt, with and without superheat, showed good agreement with alternative finite-difference techniques

Thermoelectric and morphological effects of Peltier pulsing on directional solidification of eutectic Bi-Mn

Science.gov (United States)

Silberstein, R. P.; Larson, D. J., Jr.; Dressler, B.

1984-01-01

Extensive in situ thermal measurements using Peltier Interface Demarcation (PID) during directional solidification of eutectic Bi/MnBi were carried out. Observations indicate that significant thermal transients occur throughout the sample as a result of the Peltier pulsing. The contributions of the Peltier, Thomson, and Joule heats were separated and studied as a function of pulse intensity and polarity. The Joule and the combined Peltier and Thomson thermal contributions were determined as a function of time during and after the current pulses, close to the solid/liquid interface. Variations of the Bi/MnBi particle morphology clearly reveal the interface shape, changes in interface velocity, meltback, and temporary loss of cooperative growth, as a result of the pulsing.

Cognate xenoliths in Mt. Etna lavas: witnesses of the high-velocity body beneath the volcano

Science.gov (United States)

Corsaro, Rosa Anna; Rotolo, Silvio Giuseppe; Cocina, Ornella; Tumbarello, Gianvito

2014-01-01

Various xenoliths have been found in lavas of the 1763 ("La Montagnola"), 2001, and 2002-03 eruptions at Mt. Etna whose petrographic evidence and mineral chemistry exclude a mantle origin and clearly point to a cognate nature. Consequently, cognate xenoliths might represent a proxy to infer the nature of the high-velocity body (HVB) imaged beneath the volcano by seismic tomography. Petrography allows us to group the cognate xenoliths as follows: i) gabbros with amphibole and amphibole-bearing mela-gabbros, ii) olivine-bearing leuco-gabbros, iii) leuco-gabbros with amphibole, and iv) Plg-rich leuco gabbros. Geobarometry estimates the crystallization pressure of the cognate xenoliths between 1.9 and 4.1 kbar. The bulk density of the cognate xenoliths varies from 2.6 to 3.0 g/cm3. P wave velocities (V P ), calculated in relation to xenolith density, range from 4.9 to 6.1 km/s. The integration of mineralogical, compositional, geobarometric data, and density-dependent V P with recent literature data on 3D V P seismic tomography enabled us to formulate the first hypothesis about the nature of the HVB which, in the depth range of 3-13 km b.s.l., is likely made of intrusive gabbroic rocks. These are believed to have formed at the "solidification front", a marginal zone that encompasses a deep region (>5 km b.s.l.) of Mt. Etna's plumbing system, within which magma crystallization takes place. The intrusive rocks were afterwards fragmented and transported as cognate xenoliths by the volatile-rich and fast-ascending magmas of the 1763 "La Montagnola", 2001 and 2002-03 eruptions.

Competitive grain growth in directional solidification investigated by phase field simulation

International Nuclear Information System (INIS)

Li Junjie; Wang Zhijun; Wang Jincheng; Yang Yujuan

2012-01-01

During directional solidification, the competitive dendritic growth between various oriented grains is a key factor to obtain desirable texture. In order to understand the mechanism of competitive dendritic growth, the phase field method was adopted to simulate the microstructure evolution of bicrystal samples. The simulation has well reproduced the whole competitive growth process for both diverging and converging dendrites. In converging case, besides the block of the unfavorably oriented dendrite by the favorably oriented one, the unfavorably oriented dendrite is also able to overgrow the favorable one under the condition of relatively low pulling velocity. This unusual overgrowth is dictated by the solute interaction of the converging dendrite tips. In diverging case, it was found that the grain boundary can be either inclined or parallel to the favorably oriented grain depending on the disposition of two grains.

On the stable eutectic solidification of iron–carbon–silicon alloys

International Nuclear Information System (INIS)

Stefanescu, Doru M.; Alonso, Gorka; Larrañaga, Pello; Suarez, Ramon

2016-01-01

Extensive effort was expanded to elucidate the growth and morphology of the stable eutectic grains during early solidification of continuous cooled Fe–C–Si alloys. To this purpose, quenching experiments at successive stages during solidification have been carried out on five cast irons with various magnesium and titanium levels designed to produce graphite morphologies ranging from lamellar to mixed compacted–spheroidal. The graphite shape factors were measured on the metallographic samples, and their evolution as a function of the chemical composition and the solid fraction was analyzed. Extensive scanning electron microscopy was carried on to evaluate the change in graphite shape during early solidification, to establish the fraction of solid at which the transition from spheroidal-to-compacted-to-lamellar graphite occurs, and to outline the early morphology of the eutectic grains. It was confirmed that solidification of Mg containing irons started with the development of spheroidal graphite even at Mg levels as low as 0.013 mass%. Then, as solidification proceeds, when some spheroids developed one or more tails (tadpole graphite), the spheroidal-to-compacted graphite transition occurs. The new findings were then integrated in previous knowledge to produce an understanding of the eutectic solidification of these materials. It was concluded that in hypoeutectic lamellar graphite iron austenite/graphite eutectic grains can nucleate at the austenite/liquid interface or in the bulk of the liquid, depending on the sulfur content and on the cooling rate. When graphite nucleation occurs on the primary austenite, several eutectic grains can nucleate and grow on the same dendrite. The primary austenite continues growing as eutectic austenite and therefore the two have the same crystallographic orientation. Thus, a final austenite grain may include several eutectic grains. In eutectic irons the eutectic grains nucleate and grow mostly in the liquid. The eutectic

Functional Nanoclay Suspension for Printing-Then-Solidification of Liquid Materials.

Science.gov (United States)

Jin, Yifei; Compaan, Ashley; Chai, Wenxuan; Huang, Yong

2017-06-14

Additive manufacturing (AM) enables the freeform fabrication of complex structures from various build materials. The objective of this study is to develop a novel Laponite nanoclay-enabled "printing-then-solidification" additive manufacturing approach to extrude complex three-dimensional (3D) structures made of various liquid build materials. Laponite, a member of the smectite mineral family, is investigated to serve as a yield-stress support bath material for the extrusion printing of liquid build materials. Using the printing-then-solidification approach, the printed structure remains liquid and retains its shape with the help of the Laponite support bath. Then the completed liquid structures are solidified in situ by applying suitable cross-linking mechanisms. Finally, the solidified structures are harvested from the Laponite nanoclay support bath for any further processing as needed. Due to its chemical and physical stability, liquid build materials with different solidification/curing/gelation mechanisms can be fabricated in the Laponite bath using the printing-then-solidification approach. The feasibility of the proposed Laponite-enabled printing-then-solidification approach is demonstrated by fabricating several complicated structures made of various liquid build materials, including alginate with ionic cross-linking, gelatin with thermal cross-linking, and SU-8 with photo-cross-linking. During gelatin structure printing, living cells are included and the postfabrication cell viability is above 90%.

Containerless solidification of BiFeO3 oxide under microgravity

Science.gov (United States)

Yu, Jianding; Arai, Yasutomo; Koshikawa, Naokiyo; Ishikawa, Takehito; Yoda, Shinichi

1999-07-01

Containerless solidification of BiFeO3 oxide has been carried out under microgravity with Electrostatic Levitation Furnace (ELF) aboard on the sounding rocket (TR-IA). It is a first containerless experiment using ELF under microgravity for studying the solidification of oxide insulator material. Spherical BiFeO3 sample with diameter of 5mm was heated by two lasers in oxygen and nitrogen mixing atmosphere, and the sample position by electrostatic force under pinpoint model and free drift model. In order to compare the solidification behavior in microgravity with on ground, solidification experiments of BiFeO3 in crucible and drop tube were carried out. In crucible experiment, it was very difficult to get single BiFeO3 phase, because segregation of Fe2O3 occured very fast and easily. In drop tube experiment, fine homogeneous BiFeO3 microstructure was obtained in a droplet about 300 μm. It implies that containerless processing can promote the phase selection in solidification. In microgravity experiment, because the heating temperature was lower than that of estimated, the sample was heated into Fe2O3+liquid phase region. Fe2O3 single crystal grew on the surface of the spherical sample, whose sample was clearly different from that observed in ground experiments.

Numerical simulation of freckle formation in directional solidification of binary alloys

Science.gov (United States)

Felicelli, Sergio D.; Heinrich, Juan C.; Poirier, David R.

1992-01-01

A mathematical model of solidification is presented which simulates the formation of segregation models known as 'freckles' during directional solidification of binary alloys. The growth of the two-phase or dendritic zone is calculated by solving the coupled equations of momentum, energy, and solute transport, as well as maintaining the thermodynamic constraints dictated by the phase diagram of the alloy. Calculations for lead-tin alloys show that the thermosolutal convection in the dendritic zone during solidification can produce heavily localized inhomogeneities in the composition of the final alloy.

Localized structures and front propagation in the Lengyel-Epstein model

DEFF Research Database (Denmark)

Jensen, O.; Pannbacker, Viggo Ole; Mosekilde, Erik

1994-01-01

Pattern selection, localized structure formation, and front propagation are analyzed within the framework of a model for the chlorine dioxide-iodine-malonic acid reaction that represents a key to understanding recently obtained Turing structures. This model is distinguished from previously studied......, simple reaction-diffusion models by producing a strongly subcritical transition to stripes. The wave number for the modes of maximum linear gain is calculated and compared with the dominant wave number for the finally selected, stationary structures grown from the homogeneous steady state or developed...... bifurcation. In the subcritical regime there is an interval where the front velocity vanishes as a result of a pinning of the front to the underlying structure. In 2D, two different nucleation mechanisms for hexagonal structures are illustrated on the Lengyel-Epstein and the Brusselator model. Finally...

Determination of crystal growth rates during rapid solidification of polycrystalline aluminum by nano-scale spatio-temporal resolution in situ transmission electron microscopy

Energy Technology Data Exchange (ETDEWEB)

Zweiacker, K., E-mail: Kai@zweiacker.org; Liu, C.; Wiezorek, J. M. K. [Department of Mechanical Engineering and Materials Science, University of Pittsburgh, 648 Benedum Hall, 3700 OHara Street, Pittsburgh, Pennsylvania 15261 (United States); McKeown, J. T.; LaGrange, T.; Reed, B. W.; Campbell, G. H. [Materials Science Division, Physical and Life Science Directorate, Lawrence Livermore National Laboratory, 7000 East Avenue, Livermore, California 94551 (United States)

2016-08-07

In situ investigations of rapid solidification in polycrystalline Al thin films were conducted using nano-scale spatio-temporal resolution dynamic transmission electron microscopy. Differences in crystal growth rates and asymmetries in melt pool development were observed as the heat extraction geometry was varied by controlling the proximity of the laser-pulse irradiation and the associated induced melt pools to the edge of the transmission electron microscopy support grid, which acts as a large heat sink. Experimental parameters have been established to maximize the reproducibility of the material response to the laser-pulse-related heating and to ensure that observations of the dynamical behavior of the metal are free from artifacts, leading to accurate interpretations and quantifiable measurements with improved precision. Interface migration rate measurements revealed solidification velocities that increased consistently from ∼1.3 m s{sup −1} to ∼2.5 m s{sup −1} during the rapid solidification process of the Al thin films. Under the influence of an additional large heat sink, increased crystal growth rates as high as 3.3 m s{sup −1} have been measured. The in situ experiments also provided evidence for development of a partially melted, two-phase region prior to the onset of rapid solidification facilitated crystal growth. Using the experimental observations and associated measurements as benchmarks, finite-element modeling based calculations of the melt pool evolution after pulsed laser irradiation have been performed to obtain estimates of the temperature evolution in the thin films.

Tracer filamentation at an unstable ocean front

Science.gov (United States)

Feng, Yen Chia; Mahadevan, Amala; Thiffeault, Jean-Luc; Yecko, Philip

2017-11-01

A front, where two bodies of ocean water with different physical properties meet, can become unstable and lead to a flow with high strain rate and vorticity. Phytoplankton and other oceanic tracers are stirred into filaments by such flow fields, as can often be seen in satellite imagery. The stretching and folding of a tracer by a two-dimensional flow field has been well studied. In the ocean, however, the vertical shear of horizontal velocity is typically two orders of magnitude larger than the horizontal velocity gradient. Theoretical calculations show that vertical shear alters the way in which horizontal strain affects the tracer, resulting in thin, sloping structures in the tracer field. Using a non-hydrostatic ocean model of an unstable ocean front, we simulate tracer filamentation to identify the effect of vertical shear on the deformation of the tracer. In a complementary laboratory experiment, we generate a simple, vertically sheared strain flow and use dye and particle image velocimetry to quantify the filamentary structures in terms of the strain and shear. We identify how vertical shear alters the tracer filaments and infer how the evolution of tracers in the ocean will differ from the idealized two-dimensional paradigm. Support of NSF DMS-1418956 is acknowledged.

Ionization waves of arbitrary velocity driven by a flying focus

Science.gov (United States)

Palastro, J. P.; Turnbull, D.; Bahk, S.-W.; Follett, R. K.; Shaw, J. L.; Haberberger, D.; Bromage, J.; Froula, D. H.

2018-03-01

A chirped laser pulse focused by a chromatic lens exhibits a dynamic, or flying, focus in which the trajectory of the peak intensity decouples from the group velocity. In a medium, the flying focus can trigger an ionization front that follows this trajectory. By adjusting the chirp, the ionization front can be made to travel at an arbitrary velocity along the optical axis. We present analytical calculations and simulations describing the propagation of the flying focus pulse, the self-similar form of its intensity profile, and ionization wave formation. The ability to control the speed of the ionization wave and, in conjunction, mitigate plasma refraction has the potential to advance several laser-based applications, including Raman amplification, photon acceleration, high-order-harmonic generation, and THz generation.

Microstructural investigation of D2 tool steel during rapid solidification

Science.gov (United States)

Delshad Khatibi, Pooya

Solidification is considered as a key processing step in developing the microstructure of most metallic materials. It is, therefore, important that the solidification process can be designed and controlled in such a way so as to obtain the desirable properties in the final product. Rapid solidification refers to the system's high undercooling and high cooling rate, which can yield a microstructure with unique chemical composition and mechanical properties. An area of interest in rapid solidification application is high-chromium, high-carbon tool steels which experience considerable segregation of alloying elements during their solidification in a casting process. In this dissertation, the effect of rapid solidification (undercooling and cooling rate) of D2 tool steel on the microstructure and carbide precipitation during annealing was explored. A methodology is described to estimate the eutectic and primary phase undercooling of solidifying droplets. The estimate of primary phase undercooling was confirmed using an online measurement device that measured the radiation energy of the droplets. The results showed that with increasing primary phase and eutectic undercooling and higher cooling rate, the amount of supersaturation of alloying element in metastable retained austenite phase also increases. In the case of powders, the optimum hardness after heat treatment is achieved at different temperatures for constant periods of time. Higher supersaturation of austenite results in obtaining secondary hardness at higher annealing temperature. D2 steel ingots generated using spray deposition have high eutectic undercooling and, as a result, high supersaturation of alloying elements. This can yield near net shape D2 tool steel components with good mechanical properties (specifically hardness). The data developed in this work would assist in better understanding and development of near net shape D2 steel spray deposit products with good mechanical properties.

Interstellar material in front of chi ophiuchi. I. Optical observations

International Nuclear Information System (INIS)

Frisch, P.C.

1979-01-01

Optical observations of the interstellar material in front of chi Oph are discussed. The main interstellar cloud is made up of several regions with velocities between -6 and -12 km s -1 (heliocentric). Both CH and CH + are found within this feature, but with central velocities which differ by 2 km s -1 . Another cloud, with a velocity of -26 km s -1 , contains relatively strong Ca + lines. It has a ratio between Ca + and Na 0 column densities that is appropriate for ''high-velocity'' clouds. Calcium, iron, and sodium column densities are used to estimate an average electron density for the line of sight as well as for each cloud. The abundances of CH and CH + , and the absence of CN, are analyzed in terms of current theories about their origin

Non-Equilibrium Solidification of Undercooled Metallic Melts

Directory of Open Access Journals (Sweden)

Dieter M. Herlach

2014-06-01

Full Text Available If a liquid is undercooled below its equilibrium melting temperature an excess Gibbs free energy is created. This gives access to solidification of metastable solids under non-equilibrium conditions. In the present work, techniques of containerless processing are applied. Electromagnetic and electrostatic levitation enable to freely suspend a liquid drop of a few millimeters in diameter. Heterogeneous nucleation on container walls is completely avoided leading to large undercoolings. The freely suspended drop is accessible for direct observation of rapid solidification under conditions far away from equilibrium by applying proper diagnostic means. Nucleation of metastable crystalline phases is monitored by X-ray diffraction using synchrotron radiation during non-equilibrium solidification. While nucleation preselects the crystallographic phase, subsequent crystal growth controls the microstructure evolution. Metastable microstructures are obtained from deeply undercooled melts as supersaturated solid solutions, disordered superlattice structures of intermetallics. Nucleation and crystal growth take place by heat and mass transport. Comparative experiments in reduced gravity allow for investigations on how forced convection can be used to alter the transport processes and design materials by using undercooling and convection as process parameters.

Geometrical modulus of a casting and its influence on solidification process

Directory of Open Access Journals (Sweden)

F. Havlicek

2011-10-01

Full Text Available Object: The work analyses the importance of the known criterion for evaluating the controlled solidification of castings, so called geometrical modulus defined by N. Chvorinov as the first one. Geometrical modulus influences the solidification process. The modulus has such specificity that during the process of casting formation it is not a constant but its initial value decreases with the solidification progress because the remaining melt volume can decrease faster than its cooling surface.Methodology: The modulus is determined by a simple calculation from the ratio of the casting volume after pouring the metal in the mould to the cooled mould surface. The solidified metal volume and the cooled surface too are changed during solidification. That calculation is much more complicated. Results were checked up experimentally by measuring the temperatures in the cross-section of heavy steel castings during cooling them.Results: The given experimental results have completed the original theoretical calculations by Chvorinov and recent researches done with use of numerical calculations. The contribution explains how the geometrical modulus together with the thermal process in the casting causes the higher solidification rate in the axial part of the casting cross-section and shortening of solidification time. Practical implications: Change of the geometrical modulus negatively affects the casting internal quality. Melt feeding by capillary filtration in the dendritic network in the casting central part decreases and in such a way the shrinkage porosity volume increases. State of stress character in the casting is changed too and it increases.

Solidification processing of intermetallic Nb-Al alloys

Science.gov (United States)

Smith, Preston P.; Oliver, Ben F.; Noebe, Ronald D.

1992-01-01

Several Nb-Al alloys, including single-phase NbAl3 and the eutectic of Nb2Al and NbAl3, were prepared either by nonconsumable arc melting in Ar or by zone processing in He following initial induction melting and rod casting, and the effect of the solidification route on the microstructure and room-temperature mechanical properties of these alloys was investigated. Automated control procedures and melt conditions for directional solidification of NbAl3 and the Nb2Al/Nb3Al eutectic were developed; high purity and stoichiometry were obtained. The effects of ternary additions of Ti and Ni are described.

Heat transfer and solidification processes of alloy melt with undercooling: I. Experimental results

International Nuclear Information System (INIS)

Yoshioka, Hideaki; Tada, Yukio; Kunimine, Kanji; Furuichi, Taira; Hayashi, Yujiro

2006-01-01

The solidification process of Pb-Sn and Bi-Sn alloy melts is discussed to obtain a basic understanding of the essential phenomena of solidification with undercooling. First, from macroscopic observations, it is shown that the solidification process consists of the following three stages: (1) free growth with recalescence dissipation of thermal undercooling (2) expansion of crystals with the relaxation of constitutional undercooling or with the recovering process of interrupted quasi-steady heat conduction, and (3) equilibrium solidification. The specific features of free growth under non-uniform undercooling are also shown by comparison with the Lipton, Glicksman, and Kurz model. Next, from microscopic observations, the distribution of the solute concentration and the change of crystal morphology in the solidified materials were investigated quantitatively using scanning electron microscopy and energy-dispersive spectroscopy. Finally, the solidification path during the above three fundamental processes is dynamically represented on phase diagrams

Melting, solidification, remelting, and separation of glass and metal

International Nuclear Information System (INIS)

Ebadian, M.A.; Xin, R.C.; Liu, Y.Z.

1998-01-01

Several high-temperature vitrification technologies have been developed for the treatment of a wide range of mixed waste types in both the low-level waste and transuranic (TRU) mixed waste categories currently in storage at DOE sites throughout the nation. The products of these processes are an oxide slag phase and a reduced metal phase. The metal phase has the potential to be recycled within the DOE Complex. Enhanced slag/metal separation methods are needed to support these processes. This research project involves an experimental investigation of the melting, solidification, remelting, and separation of glass and metal and the development of an efficient separation technology. The ultimate goal of this project is to find an efficient way to separate the slag phase from the metal phase in the molten state. This two-year project commenced in October 1995 (FY96). In the first fiscal year, the following tasks were accomplished: (1) A literature review and an assessment of the baseline glass and metal separation technologies were performed. The results indicated that the baseline technology yields a high percentage of glass in the metal phase, requiring further separation. (2) The main melting and solidification system setup was established. A number of melting and solidification tests were conducted. (3) Temperature distribution, solidification patterns, and flow field in the molten metal pool were simulated numerically for the solidification processes of molten aluminum and iron steel. (4) Initial designs of the laboratory-scale DCS and CS technologies were also completed. The principal demonstration separation units were constructed. (5) An application for a patent for an innovative liquid-liquid separation technology was submitted and is pending

Modified sulfur cement solidification of low-level wastes

Energy Technology Data Exchange (ETDEWEB)

1985-10-01

This topical report describes the results of an investigation on the solidification of low-level radioactive wastes in modified sulfur cement. The work was performed as part of the Waste Form Evaluation Program, sponsored by the US Department of Energy's Low-Level Waste Management Program. Modified sulfur cement is a thermoplastic material developed by the US Bureau of Mines. Processing of waste and binder was accomplished by means of both a single-screw extruder and a dual-action mixing vessel. Waste types selected for this study included those resulting from advanced volume reduction technologies (dry evaporator concentrate salts and incinerator ash) and those which remain problematic for solidification using contemporary agents (ion exchange resins). Process development studies were conducted to ascertain optimal process control parameters for successful solidification. Maximum waste loadings were determined for each waste type and method of processing. Property evaluation testing was carried out on laboratory scale specimens in order to compare with waste form performance for other potential matrix materials. Waste form property testing included compressive strength, water immersion, thermal cycling and radionuclide leachability. Recommended waste loadings of 40 wt. % sodium sulfate and boric acid salts and 43 wt. % incinerator ash, which are based on processing and performance considerations, are reported. Solidification efficiencies for these waste types represent significant improvements over those of hydraulic cements. Due to poor waste form performance, incorporation of ion exchange resin waste in modified sulfur cement is not recommended.

Modified sulfur cement solidification of low-level wastes

International Nuclear Information System (INIS)

1985-10-01

This topical report describes the results of an investigation on the solidification of low-level radioactive wastes in modified sulfur cement. The work was performed as part of the Waste Form Evaluation Program, sponsored by the US Department of Energy's Low-Level Waste Management Program. Modified sulfur cement is a thermoplastic material developed by the US Bureau of Mines. Processing of waste and binder was accomplished by means of both a single-screw extruder and a dual-action mixing vessel. Waste types selected for this study included those resulting from advanced volume reduction technologies (dry evaporator concentrate salts and incinerator ash) and those which remain problematic for solidification using contemporary agents (ion exchange resins). Process development studies were conducted to ascertain optimal process control parameters for successful solidification. Maximum waste loadings were determined for each waste type and method of processing. Property evaluation testing was carried out on laboratory scale specimens in order to compare with waste form performance for other potential matrix materials. Waste form property testing included compressive strength, water immersion, thermal cycling and radionuclide leachability. Recommended waste loadings of 40 wt. % sodium sulfate and boric acid salts and 43 wt. % incinerator ash, which are based on processing and performance considerations, are reported. Solidification efficiencies for these waste types represent significant improvements over those of hydraulic cements. Due to poor waste form performance, incorporation of ion exchange resin waste in modified sulfur cement is not recommended

Stabilization/Solidification Remediation Method for Contaminated Soil: A Review

Science.gov (United States)

Tajudin, S. A. A.; Azmi, M. A. M.; Nabila, A. T. A.

2016-07-01

Stabilization/Solidification (S/S) is typically a process that involves a mixing of waste with binders to reduce the volume of contaminant leachability by means of physical and chemical characteristics to convert waste in the environment that goes to landfill or others possibly channels. Stabilization is attempts to reduce the solubility or chemical reactivity of the waste by changing the physical and chemical properties. While, solidification attempt to convert the waste into easily handled solids with low hazardous level. These two processes are often discussed together since they have a similar purpose of improvement than containment of potential pollutants in treated wastes. The primary objective of this review is to investigate the materials used as a binder in Stabilization/Solidification (S/S) method as well as the ability of these binders to remediate the contaminated soils especially by heavy metals.

MODELING SOLIDIFICATION-INDUCED STRESSES IN CERAMIC WASTE FORMS CONTAINING NUCLEAR WASTES

International Nuclear Information System (INIS)

Solbrig, Charles W.; Bateman, Kenneth J.

2010-01-01

The goal of this work is to produce a ceramic waste form (CWF) that permanently occludes radioactive waste. This is accomplished by absorbing radioactive salts into zeolite, mixing with glass frit, heating to a molten state 915 C to form a sodalite glass matrix, and solidifying for long-term storage. Less long term leaching is expected if the solidifying cooling rate doesn't cause cracking. In addition to thermal stress, this paper proposes that a stress is formed during solidification which is very large for fast cooling rates during solidification and can cause severe cracking. A solidifying glass or ceramic cylinder forms a dome on the cylinder top end. The temperature distribution at the time of solidification causes the stress and the dome. The dome height, ''the length deficit,'' produces an axial stress when the solid returns to room temperature with the inherent outer region in compression, the inner in tension. Large tensions will cause cracking of the specimen. The temperature deficit, derived by dividing the length deficit by the coefficient of thermal expansion, allows solidification stress theory to be extended to the circumferential stress. This paper derives the solidification stress theory, gives examples, explains how to induce beneficial stresses, and compares theory to experimental data.

Modeling of complex melting and solidification behavior in laser-irradiated materials [a description and users guide to the LASER8 computer program

International Nuclear Information System (INIS)

Geist, G.A.; Wood, R.F.

1985-11-01

The conceptual foundation of a computational model and a computer program based on it have been developed for treating various aspects of the complex melting and solidification behavior observed in pulsed laser-irradiated materials. A particularly important feature of the modeling is the capability of allowing melting and solidification to occur at temperatures other than the thermodynamic phase change temperatures. As a result, interfacial undercooling and overheating can be introduced and various types of nucleation events can be simulated. Calculations on silicon with the model have shown a wide variety of behavior, including the formation and propagation of multiple phase fronts. Although originally developed as a tool for studying certain problems arising in the field of laser annealing of semiconductors, the program should be useful in treating many types of systems in which phase changes and nucleation phenomena play important roles. This report describes the underlying physical and mathematical ideas and the basic relations used in LASER8. It also provides enough specific and detailed information on the program to serve as a guide for its use; a listing of one version of the program is given

Solidification of low-level wastes by inorganic binder

International Nuclear Information System (INIS)

Sasaki, M.T.; Shimojo, M.; Suzuki, K.; Kajikawa, A.; Karasawa, Y.

1995-01-01

The use of an alkali activated slag binder has been studied for solidification and stabilization of low-level wastes in nuclear power stations and spent fuel processing facilities. The activated slag effectively formed waste products having good physical properties with high waste loading for sodium sulfate, sodium nitrate, calcium pyrophosphate/phosphate and spent ion-exchange resins. Moreover, the results of the study suggest the slag has the ability to become a common inorganic binder for the solidification of various radioactive wastes. This paper also describes the fixation of radionuclides by the activated slag binder

Three-dimensional phase-field simulations of directional solidification

Science.gov (United States)

Plapp, Mathis

2007-05-01

The phase-field method has become the method of choice for simulating microstructural pattern formation during solidification. One of its main advantages is that time-dependent three-dimensional simulations become feasible, which makes it possible to address long-standing questions of pattern stability and pattern selection. Here, a brief introduction to the phase-field model and its implementation is given, and its capabilities are illustrated by examples taken from the directional solidification of binary alloys. In particular, the morphological stability of hexagonal cellular arrays and of eutectic lamellar patterns is investigated.

Solidification in Multicomponent Multiphase Systems (SIMMS)

Science.gov (United States)

Rex, S.; Hecht, U.

2005-06-01

The multiphase microstructures that evolve during the solidification of multicomponent alloys are attracting widespread interest for industrial applications and fundamental research.Thermodynamic databases are now well-established for many alloy systems. Thermodynamic calculations provide all the required information about phase equilibria, forming an integral part of both dedicated and comprehensive microstructure models. Among the latter, phase-field modelling has emerged as the method of choice. Solidification experiments are intended to trigger model development or to serve as benchmarks for model validation. For benchmarking, microgravity conditions offer a unique opportunity for avoiding buoyancy-induced convection and buoyancy forces in bulk samples. However, diffusion and the free-energy of interfaces and its anisotropy need to be determined.The measurement of chemical diffusivities in the liquid state can equally benefit from microgravity experiments.

Measuring device for weight of glass of glass solidification product to be charged

International Nuclear Information System (INIS)

Yasutake, Nobuhiro; Arai, Masaki; Akashi, Ken-ichi

1998-01-01

The present invention provides a device for accurately calculating the weight of molten glass to be charged during manufacturing glass solidification products of radioactive liquid wastes. Namely, a discharge nozzle at the lower end of a glass melting furnace and an upper end of a vessel for glass solidification materials are connected by a connecting device extensible vertically in a cylindrical shape. Molten glasses are flown down by way of the connecting device and filled into the vessel for solidification products. A first scale is constituted so as to measure the weight of load, and the vessel for solidification products are loaded. A second scale is constituted so as to measure the own weight and a weight of load, and is interposed between a flange at the circumference of a charging port and the lower end of the connecting device, and has an opening for flowing down the molten glass at the central portion. With such a constitution, the first scale can weigh the total of the weight of molten glass charged to the vessel for solidification products, the weight of the vessel for solidification products, the counterforce from the connecting device and the weight of the second scale. If the measured value of the secondary scale and the weight of the vessel for solidification products are subtracted from the former value, the weight of the charged molten glass can be determined. (I.S.)

PREFACE: Third International Conference on Advances in Solidification Processes (ICASP - 3)

Science.gov (United States)

Zimmermann, Gerhard; Ratke, Lorenz

2012-01-01

The 3rd International Conference on Advances in Solidification Processes was held in the Rolduc Abbey in the Netherlands a few kilometres away from Aachen. Around 200 scientists from 24 countries come in for the four day meeting. They found a stimulating but also relaxing environment and atmosphere, with beautiful weather and the medieval abbey inviting for walks, discussions, sitting outside and drinking a beer or wine. The contributions given at the conference reflected recent advances in various topics of solidification processes, ranging from fundamental aspects to applied casting technologies. In 20 oral sessions and a large poster session innovative results of segregation phenomena, microstructure evolution, nucleation and growth, phase formation, polyphase solidification, rapid solidification and welding, casting technology, thermophysics of molten alloys, solidification with forced melt flow and growth of single crystals and superalloys together with innovative diagnostic techniques were presented. Thereby, findings from experiments as well as from numerical modeling on different lengths scales were jointly discussed and contribute to new insight in solidification behaviour. The papers presented in this open access proceedings cover about half the oral and poster presentations given. They were carefully reviewed as in classical peer reviewed journals by two independent referees and most of them were revised and thus improved according to the reviewers comments. We think that this collection of papers presented at ICASP-3 gives an impression of the excellent contributions made. The papers embrace both the basic and applied aspects of solidification. We especially wish to express our appreciation for the team around Georg Schmitz and Margret Nienhaus organising this event and giving us their valued advice and support at every stage in preparing the conference. We also thank Lokasenna Lektorat for taking the task of checking all language-associated issues and

Microstructure and Corrosion Resistance Property of a Zn-AI-Mg Alloy with Different Solidification Processes

Directory of Open Access Journals (Sweden)

Jiang Guang-rui

2017-01-01

Full Text Available Zn-Al-Mg alloy coating attracted much attention due to its high corrosion resistance properties, especially high anti-corrosion performance at the cut edge. As the Zn-Al-Mg alloy coating was usually produced by hot-dip galvanizing method, solidification process was considered to influence its microstructure and corrosion properties. In this work, a Zn-Al-Mg cast alloy was melted and cooled to room temperature with different solidification processes, including water quench, air cooling and furnace cooling. Microstructure of the alloy with different solidification processes was characterized by scanning electron microscopy (SEM. Result shows that the microstructure of the Zn-Al-Mg alloy are strongly influenced by solidification process. With increasing solidification rate, more Al is remained in the primary crystal. Electrochemical analysis indicates that with lowering solidification rate, the corrosion current density of the Zn-Al-Mg alloy decreases, which means higher corrosion resistance.

Velocity distribution in snow avalanches

Science.gov (United States)

Nishimura, K.; Ito, Y.

1997-12-01

In order to investigate the detailed structure of snow avalanches, we have made snow flow experiments at the Miyanomori ski jump in Sapporo and systematic observations in the Shiai-dani, Kurobe Canyon. In the winter of 1995-1996, a new device to measure static pressures was used to estimate velocities in the snow cloud that develops above the flowing layer of avalanches. Measurements during a large avalanche in the Shiai-dani which damaged and destroyed some instruments indicate velocities increased rapidly to more than 50 m/s soon after the front. Velocities decreased gradually in the following 10 s. Velocities of the lower flowing layer were also calculated by differencing measurement of impact pressure. Both recordings in the snow cloud and in the flowing layer changed with a similar trend and suggest a close interaction between the two layers. In addition, the velocity showed a periodic change. Power spectrum analysis of the impact pressure and the static pressure depression showed a strong peak at a frequency between 4 and 6 Hz, which might imply the existence of either ordered structure or a series of surges in the flow.

Mesoscopic simulation of dendritic growth observed in x-ray video microscopy during directional solidification of Al-Cu alloys

International Nuclear Information System (INIS)

Delaleau, Pierre; Beckermann, Christoph; Mathiesen, Ragnvald H.; Arnberg, Lars

2010-01-01

A mesoscopic model is developed to simulate microstructures observed in situ by X-ray video microscopy during directional solidification of Al-Cu alloys in a Hele-Shaw cell. In the model, a volume-averaged species conservation equation is solved to obtain the solute concentration and solid fraction fields, and an analytical stagnant film model is used to predict the motion of the dendrite envelopes. The model is carefully validated in several test cases. Then, the model is applied to simulate the columnar dendritic microstructures observed in the X-ray video microscopy experiments for two different alloy compositions. Reasonable agreement is found between the measured and predicted dendrite envelope shapes, solid fractions, and solute concentration fields. The predicted size of the mushy zone and the extent of the undercooled melt region ahead of the columnar front agree well with the in situ experimental observations. The simulation results show quantitative agreement with the internal solid fraction variations measured from the radiographs. The present model is also able to realistically simulate a primary dendrite trunk spacing adjustment that was observed in one of the experiments. Overall, the present study represents the first successful validation of a solidification model using real time, in situ data from an experiment with a metallic alloy. Considerable additional research is needed to account in the model for the effect of gravity driven melt convection. (author)

Premature melt solidification during mold filling and its influence on the as-cast structure

Science.gov (United States)

Wu, M.; Ahmadein, M.; Ludwig, A.

2018-03-01

Premature melt solidification is the solidification of a melt during mold filling. In this study, a numerical model is used to analyze the influence of the pouring process on the premature solidification. The numerical model considers three phases, namely, air, melt, and equiaxed crystals. The crystals are assumed to have originated from the heterogeneous nucleation in the undercooled melt resulting from the first contact of the melt with the cold mold during pouring. The transport of the crystals by the melt flow, in accordance with the socalled "big bang" theory, is considered. The crystals are assumed globular in morphology and capable of growing according to the local constitutional undercooling. These crystals can also be remelted by mixing with the superheated melt. As the modeling results, the evolutionary trends of the number density of the crystals and the volume fraction of the solid crystals in the melt during pouring are presented. The calculated number density of the crystals and the volume fraction of the solid crystals in the melt at the end of pouring are used as the initial conditions for the subsequent solidification simulation of the evolution of the as-cast structure. A five-phase volume-average model for mixed columnar-equiaxed solidification is used for the solidification simulation. An improved agreement between the simulation and experimental results is achieved by considering the effect of premature melt solidification during mold filling. Finally, the influences of pouring parameters, namely, pouring temperature, initial mold temperature, and pouring rate, on the premature melt solidification are discussed.

Solidification behavior of austenitic stainless steel filler metals

International Nuclear Information System (INIS)

David, S.A.; Goodwin, G.M.; Braski, D.N.

1980-02-01

Thermal analysis and interrupted solidification experiments on selected austenitic stainless steel filler metals provided an understanding of the solidification behavior of austenitic stainless steel welds. The sequences of phase separations found were for type 308 stainless steel filler metal, L + L + delta + L + delta + γ → γ + delta, and for type 310 stainless steel filler metal, L → L + γ → γ. In type 308 stainless steel filler metal, ferrite at room temperature was identified as either the untransformed primary delta-ferrite formed during the initial stages of solidification or the residual ferrite after Widmanstaetten austenite precipitation. Microprobe and scanning transmission electron microscope microanalyses revealed that solute extensively redistributes during the transformation of primary delta-ferrite to austenite, leading to enrichment and stabilization of ferrite by chromium. The type 310 stainless steel filler metal investigated solidifies by the primary crystallization of austenite, with the transformation going to completion at the solidus temperature. In our samples residual ferrite resulting from solute segregation was absent at the intercellular or interdendritic regions

Field theory of propagating reaction-diffusion fronts

International Nuclear Information System (INIS)

Escudero, C.

2004-01-01

The problem of velocity selection of reaction-diffusion fronts has been widely investigated. While the mean-field limit results are well known theoretically, there is a lack of analytic progress in those cases in which fluctuations are to be taken into account. Here, we construct an analytic theory connecting the first principles of the reaction-diffusion process to an effective equation of motion via field-theoretic arguments, and we arrive at results already confirmed by numerical simulations

Stability of cosmological deflagration fronts

Science.gov (United States)

Mégevand, Ariel; Membiela, Federico Agustín

2014-05-01

In a cosmological first-order phase transition, bubbles of the stable phase nucleate and expand in the supercooled metastable phase. In many cases, the growth of bubbles reaches a stationary state, with bubble walls propagating as detonations or deflagrations. However, these hydrodynamical solutions may be unstable under corrugation of the interface. Such instability may drastically alter some of the cosmological consequences of the phase transition. Here, we study the hydrodynamical stability of deflagration fronts. We improve upon previous studies by making a more careful and detailed analysis. In particular, we take into account the fact that the equation of motion for the phase interface depends separately on the temperature and fluid velocity on each side of the wall. Fluid variables on each side of the wall are similar for weakly first-order phase transitions, but differ significantly for stronger phase transitions. As a consequence, we find that, for large enough supercooling, any subsonic wall velocity becomes unstable. Moreover, as the velocity approaches the speed of sound, perturbations become unstable on all wavelengths. For smaller supercooling and small wall velocities, our results agree with those of previous works. Essentially, perturbations on large wavelengths are unstable, unless the wall velocity is higher than a critical value. We also find a previously unobserved range of marginally unstable wavelengths. We analyze the dynamical relevance of the instabilities, and we estimate the characteristic time and length scales associated with their growth. We discuss the implications for the electroweak phase transition and its cosmological consequences.

On the relation between primary and eutectic solidification structures in gray iron

International Nuclear Information System (INIS)

Elmquist, L; Sonawane, P A

2012-01-01

The solidification of hypoeutectic gray cast iron starts with the nucleation of primary austenite crystals. Before graphite is nucleated, and the eutectic structure is formed, these crystals start to grow as columnar or equiaxed dendrites. However, very little is known about these dendrites, and especially how they influence the subsequent eutectic structure. Besides, it has previously been shown that the primary solidification structure influences the formation of defects. Shrinkage porosity was found between the dendrites, in the grain boundaries, and the formation of the primary solidification structure was found to influence problems related to metal expansion penetration. Therefore a better understanding about the formation of this structure is of importance. In this work, different inoculants and their influence on the formation of the micro- and macrostructures has been investigated. The inoculants considered are commercially used inoculants, i.e. inoculants used in the foundries, as well as different iron powders. The addition of iron powder is used to promote the primary solidification structure. It is shown that the nucleation of the dendrites is influenced by the amount of iron powder. Secondary dendrite arm spacing is a quantitative measurement in the microstructure related to these dendrites, which in turn depends on the solidification time. Eutectic cell size, on the other hand, is found to depend on secondary dendrite arm spacing. It is shown how the addition of inoculants influences both primary and eutectic solidification structures, and how they are related to each other.

Morphological stability of Sm123 superconductor during peritectic solidification from Sm211 + L mixture

International Nuclear Information System (INIS)

Sumida, Masaki; Shiohara, Yuh; Umeda, Takateru

2000-01-01

The interface stability of the Sm 123 superconductor was analyzed in accordance with the constitutional undercooling criterion. As the single-crystal growth of the 123 phase is largely dependent on the growth-interface stability, a quantitative analysis was very much required. From this analysis, it was clarified that the constitutional undercooling must exist in the liquid when the 123 growth interface comes close to a 211 particle during the peritectic solidification. It was also predicted that the larger 211 particle radius, smaller volume fraction of the 211 particles, larger growth rate, or smaller imposed temperature gradient would cause easy occurrence of the constitutional undercooling ahead of the 123 growth interface. Taking into account the nucleation at the L/211 interface just ahead of the 123 growth front due to the constitutional undercooling, the transition of 123 growth from a planar-interface morphology to an equiaxed blocky morphology was investigated quantitatively and qualitatively

Bifurcating fronts for the Taylor-Couette problem in infinite cylinders

Science.gov (United States)

Hărăguş-Courcelle, M.; Schneider, G.

We show the existence of bifurcating fronts for the weakly unstable Taylor-Couette problem in an infinite cylinder. These fronts connect a stationary bifurcating pattern, here the Taylor vortices, with the trivial ground state, here the Couette flow. In order to show the existence result we improve a method which was already used in establishing the existence of bifurcating fronts for the Swift-Hohenberg equation by Collet and Eckmann, 1986, and by Eckmann and Wayne, 1991. The existence proof is based on spatial dynamics and center manifold theory. One of the difficulties in applying center manifold theory comes from an infinite number of eigenvalues on the imaginary axis for vanishing bifurcation parameter. But nevertheless, a finite dimensional reduction is possible, since the eigenvalues leave the imaginary axis with different velocities, if the bifurcation parameter is increased. In contrast to previous work we have to use normalform methods and a non-standard cut-off function to obtain a center manifold which is large enough to contain the bifurcating fronts.

Solidification analysis of a centrifugal atomizer using the Al-32.7wt.% Cu alloy

Energy Technology Data Exchange (ETDEWEB)

Osborne, Matthew G. [Iowa State Univ., Ames, IA (United States)

1998-02-23

A centrifugal atomizer (spinning disk variety) was designed and constructed for the production of spherical metal powders, 100-1,000 microns in diameter in an inert atmosphere. Initial atomization experiments revealed the need for a better understanding of how the liquid metal was atomized and how the liquid droplets solidified. To investigate particle atomization, Ag was atomized in air and the process recorded on high-speed film. To investigate particle solidification, Al-32.7 wt.% Cu was atomized under inert atmosphere and the subsequent particles were examined microscopically to determine solidification structure and rate. This dissertation details the experimental procedures used in producing the Al-Cu eutectic alloy particles, examination of the particle microstructures, and determination of the solidification characteristics (e.g., solidification rate) of various phases. Finally, correlations are proposed between the operation of the centrifugal atomizer and the observed solidification spacings.

Shear velocity structure of the laterally heterogeneous crust and uppermost mantle beneath the Indian region

Science.gov (United States)

Mohan, G.; Rai, S. S.; Panza, G. F.

1997-08-01

The shear velocity structure of the Indian lithosphere is mapped by inverting regionalized Rayleigh wave group velocities in time periods of 15-60 s. The regionalized maps are used to subdivide the Indian plate into several geologic units and determine the variation of velocity with depth in each unit. The Hedgehog Monte Carlo technique is used to obtain the shear wave velocity structure for each geologic unit, revealing distinct velocity variations in the lower crust and uppermost mantle. The Indian shield has a high-velocity (4.4-4.6 km/s) upper mantle which, however, is slower than other shields in the world. The central Indian platform comprised of Proterozoic basins and cratons is marked by a distinct low-velocity (4.0-4.2 km/s) upper mantle. Lower crustal velocities in the Indian lithosphere generally range between 3.8 and 4.0 km/s with the oceanic segments and the sedimentary basins marked by marginally higher and lower velocities, respectively. A remarkable contrast is observed in upper mantle velocities between the northern and eastern convergence fronts of the Indian plate. The South Bruma region along the eastern subduction front of the Indian oceanic lithosphere shows significant velocity enhancement in the lower crust and upper mantle. High velocities (≈4.8 km/s) are also observed in the upper mantle beneath the Ninetyeast ridge in the northeastern Indian Ocean.

Nucleation and solidification of thin walled ductile iron - Experiments and numerical simulation

DEFF Research Database (Denmark)

Pedersen, Karl Martin; Tiedje, Niels Skat

2005-01-01

Investigation of solidification of thin walled ductile cast iron has been performed based on experiments and numerical simulation. The experiments were based on temperature and microstructure examination. Results of the experiments have been compared with a 1-D numerical solidification model...

UNCONSTRAINED MELTING AND SOLIDIFICATION INSIDE ...

African Journals Online (AJOL)

2015-09-01

Sep 1, 2015 ... There is a large number of experimental and numerical works on melting and solidification of PCM[6-10], and also its usage as thermal management in building [11-14], electronic devices [15-16] and solar energy. [17-20].Most investigated geometries in melting and freezing process are sphere (spherical.

Process gas solidification system

International Nuclear Information System (INIS)

1980-01-01

A process for withdrawing gaseous UF 6 from a first system and directing same into a second system for converting the gas to liquid UF 6 at an elevated temperature, additionally including the step of withdrawing the resulting liquid UF 6 from the second system, subjecting it to a specified sequence of flash-evaporation, cooling and solidification operations, and storing it as a solid in a plurality of storage vessels. (author)

Alternative solidification techniques for radioactive ion exchange resins and liquid concentrates

International Nuclear Information System (INIS)

Thegerstroem, C.

1980-01-01

Methods, that are used or are under development for solidification of radioactive ion exchange resins or liquid concentrates, utilize normally cement, bitumen or some polymere as matrix material. This report contains a review and a description of these solidification processes and their products, especially of relatively new techniques that are under development in different countries. It is possible that solidification in thermosetting resins will be more used in the future, especially when product quality requirements are high (for instance when solidifying medium level resins) or when special waste categories has to be solidified. However it is not probable that thermosetting resins will be extensively used in a broad application as matrix material. In that case the methods are to complicated and expensive compared to, for instance, solidification in concrete. Systems for incorporation in polyesteremulsions (Dow-process) have a potential as they are quite simple and can accept a large variation of liquid wastes. Some methods in an early stage of development (for instance Inert Carrier Radwaste Process) will have to be tested in active application before they can be further evaluated. (author)

Numerical study of influence of inclusion movement on channel segregation in Fe- 0.21 wt% C- 0.1 wt% S alloy

International Nuclear Information System (INIS)

Liu, D R; Yang, Z P; Sun, Q Y; Wang, L P; Ma, B X

2016-01-01

A two-dimensional continuum model on solute and heat transport, and fluid flow is developed to numerically investigate the influence of inclusion movement on the development of channel segregation. A trajectory model is used to track the moving path of inclusion particles. Inclusion movement affects the flow field in simulation by means of interfacial friction coefficient. Simulations are performed on the Hebditch-Hunt casting. A parametric study is carried out to study the effects of with and without inclusions, and diameter (5 × 10 -6 m, 10 × 10 -6 m, 20 × 10 -6 m and 40 × 10 -6 m) of inclusions on channel segregation. It is found that the channel segregation is strengthened with the consideration of inclusion movement. Compared to other diameters, inclusions with diameter 20 × 10 -6 m are found to enhance the channel segregation. This is because the larger inclusions (40 × 10 -6 m) present a faster floating velocity that reduces the interaction time between inclusion upward movement and the development of solidification front, and then lessens the disturbance to solidification front that is important to the initialization of channel segregation. The upward movement of smaller inclusions (5 × 10 -6 m and 10 × 10 -6 m) cannot greatly increase the upward velocity of fluid flow. Therefore, the formation of channel segregation is less affected. (paper)

Direct measurement technique for shock wave velocity with irradiation drive

International Nuclear Information System (INIS)

Wang Feng; Peng Xiaoshi; Liu Shenye; Jiang Xiaohua; Ding Yongkun

2011-01-01

According to the ionization mechanism of transparent material under super high pressure, the direct diagnosis method of shock wave has been analyzed. With the Drude free electron model, the reflectivity difference of shock wave front under different pressures was analyzed. The blank effect in the detector was studied, which is caused by the X-ray ionization of transparent material, after analyzing the reflectivity data in space-time scale. The experiment shows that the beginning point and duration of blank effect are consistent with the start point and duration of laser pulse, respectively. And the reflectivity of shock wave front is about 35% when the shock velocity is 32 km/s. The reason and solution for blank effect was presented. The formula to calculate the shock wave velocity in transparent material was also deduced and verified. (authors)

Origin of grain orientation during solidification of an aluminum alloy

International Nuclear Information System (INIS)

Wei, H.L.; Elmer, J.W.; DebRoy, T.

2016-01-01

The evolution of grain morphology during solidification of a moving aluminum alloy pool is simulated by considering heat transfer, flow of liquid metal in the molten pool and solidification parameters. The computationally efficient model consists of a 3D coupled heat transfer and fluid flow simulation to predict the molten pool shape and temperature field, and a 2D model of grain formation in the molten pool. The results demonstrate that columnar grains grow in a curved pattern rather than along straight lines from the fusion boundary towards the center of the molten pool. The calculated results are validated with independent experimental data. The computed ratio of local temperature gradient to solidification rate, G/R, is used to model the columnar to equiaxed transition during solidification. The simulated results show that only curved columnar grains are formed when the scanning speed is low (2.0 mm/s). In contrast, a transition from curved columnar to equiaxed morphologies occurs at the higher scanning speeds of 8.0 mm/s and 11.5 mm/s, with higher equiaxed grain fraction at higher speed. The similarities between the physical processes governing fusion welding and additive manufacturing (AM) make the model capable of predicting grain orientation in both processes.

Front propagation and clustering in the stochastic nonlocal Fisher equation

Science.gov (United States)

Ganan, Yehuda A.; Kessler, David A.

2018-04-01

In this work, we study the problem of front propagation and pattern formation in the stochastic nonlocal Fisher equation. We find a crossover between two regimes: a steadily propagating regime for not too large interaction range and a stochastic punctuated spreading regime for larger ranges. We show that the former regime is well described by the heuristic approximation of the system by a deterministic system where the linear growth term is cut off below some critical density. This deterministic system is seen not only to give the right front velocity, but also predicts the onset of clustering for interaction kernels which give rise to stable uniform states, such as the Gaussian kernel, for sufficiently large cutoff. Above the critical cutoff, distinct clusters emerge behind the front. These same features are present in the stochastic model for sufficiently small carrying capacity. In the latter, punctuated spreading, regime, the population is concentrated on clusters, as in the infinite range case, which divide and separate as a result of the stochastic noise. Due to the finite interaction range, if a fragment at the edge of the population separates sufficiently far, it stabilizes as a new cluster, and the processes begins anew. The deterministic cutoff model does not have this spreading for large interaction ranges, attesting to its purely stochastic origins. We show that this mode of spreading has an exponentially small mean spreading velocity, decaying with the range of the interaction kernel.

Detonative propagation and accelerative expansion of the Crab Nebula shock front.

Science.gov (United States)

Gao, Yang; Law, Chung K

2011-10-21

The accelerative expansion of the Crab Nebula's outer envelope is a mystery in dynamics, as a conventional expanding blast wave decelerates when bumping into the surrounding interstellar medium. Here we show that the strong relativistic pulsar wind bumping into its surrounding nebula induces energy-generating processes and initiates a detonation wave that propagates outward to form the current outer edge, namely, the shock front, of the nebula. The resulting detonation wave, with a reactive downstream, then provides the needed power to maintain propagation of the shock front. Furthermore, relaxation of the curvature-induced reduction of the propagation velocity from the initial state of formation to the asymptotic, planar state of Chapman-Jouguet propagation explains the observed accelerative expansion. Potential richness in incorporating reactive fronts in the description of various astronomical phenomena is expected. © 2011 American Physical Society

Al-Si-Re Alloys Cast by the Rapid Solidification Process / Stopy Al-Si-Re Odlewane Metodą Rapid Solidification

Directory of Open Access Journals (Sweden)

Szymanek M.

2015-12-01

Full Text Available The aim of the studies described in this article was to present the effect of rare earth elements on aluminium alloys produced by an unconventional casting technique. The article gives characteristics of the thin strip of Al-Si-RE alloy produced by Rapid Solidification (RS. The effect of rare earth elements on structure refinement, i.e. on the size of near-eutectic crystallites in an aluminium-silicon alloy, was discussed. To determine the size of crystallites, the Scherrer X-ray diffraction method was used. The results presented capture relationships showing the effect of variable casting parameters and chemical composition on microstructure of the examined alloys. Rapid Solidification applied to Al-Si alloys with the addition of mischmetal (Ce, La, Ne, Pr refines their structure.

Large Eddy Simulation of Transient Flow, Solidification, and Particle Transport Processes in Continuous-Casting Mold

Science.gov (United States)

Liu, Zhongqiu; Li, Linmin; Li, Baokuan; Jiang, Maofa

2014-07-01

The current study developed a coupled computational model to simulate the transient fluid flow, solidification, and particle transport processes in a slab continuous-casting mold. Transient flow of molten steel in the mold is calculated using the large eddy simulation. An enthalpy-porosity approach is used for the analysis of solidification processes. The transport of bubble and non-metallic inclusion inside the liquid pool is calculated using the Lagrangian approach based on the transient flow field. A criterion of particle entrapment in the solidified shell is developed using the user-defined functions of FLUENT software (ANSYS, Inc., Canonsburg, PA). The predicted results of this model are compared with the measurements of the ultrasonic testing of the rolled steel plates and the water model experiments. The transient asymmetrical flow pattern inside the liquid pool exhibits quite satisfactory agreement with the corresponding measurements. The predicted complex instantaneous velocity field is composed of various small recirculation zones and multiple vortices. The transport of particles inside the liquid pool and the entrapment of particles in the solidified shell are not symmetric. The Magnus force can reduce the entrapment ratio of particles in the solidified shell, especially for smaller particles, but the effect is not obvious. The Marangoni force can play an important role in controlling the motion of particles, which increases the entrapment ratio of particles in the solidified shell obviously.

Numerical model for dendritic solidification of binary alloys

Science.gov (United States)

Felicelli, S. D.; Heinrich, J. C.; Poirier, D. R.

1993-01-01

A finite element model capable of simulating solidification of binary alloys and the formation of freckles is presented. It uses a single system of equations to deal with the all-liquid region, the dendritic region, and the all-solid region. The dendritic region is treated as an anisotropic porous medium. The algorithm uses the bilinear isoparametric element, with a penalty function approximation and a Petrov-Galerkin formulation. Numerical simulations are shown in which an NH4Cl-H2O mixture and a Pb-Sn alloy melt are cooled. The solidification process is followed in time. Instabilities in the process can be clearly observed and the final compositions obtained.

Effect of gas expansion on the front shape of a Taylor bubble: an experimental contribution

Directory of Open Access Journals (Sweden)

Santos Laura

2014-03-01

Full Text Available An experimental study where an individual Taylor bubble rises through water with different bubble volume expansion rates is presented with the (front bubble shape determination as main objective. A combination of two techniques, Particle Image Velocimetry (PIV and Pulsed Shadowgraphy (PS, was used to collect images for further treatment in order to characterize the liquid flow pattern in front of the bubble and the bubble shape. Processing the images acquired with pulsed illumination from behind the bubble it was possible to define with precision the bubble shape at different stages when it was expanding. The operation conditions used allowed a wide range of volume expansion rates (0 to 28.5 × 10-6 m3/s with a significant effect on the Taylor bubble velocity; increases in bubble velocity up to 21% were observed relatively to constant volume system condition. Nevertheless, it seems that the front shape of Taylor bubbles does not change significantly with the upward liquid flow rates induced by gas expansion, at least for the volume expansion rates used in the experiments.

Solute redistribution in dendritic solidification with diffusion in the solid

Science.gov (United States)

Ganesan, S.; Poirier, D. R.

1989-01-01

An investigation of solute redistribution during dendritic solidification with diffusion in the solid has been performed using numerical techniques. The extent of diffusion is characterized by the instantaneous and average diffusion parameters. These parameters are functions of the diffusion Fourier number, the partition ratio and the fraction solid. Numerical results are presented as an approximate model, which is used to predict the average diffusion parameter and calculate the composition of the interdendritic liquid during solidification.

Solidification of highly active liquid waste

International Nuclear Information System (INIS)

Morris, J.B.

1985-03-01

This document contains the annual progress reports on the following subjects: Joule ceramic melter; microwave vitrification; glass technology; identification, evaluation and review of potential alternative solidification processes; rotary kiln calcination; alternative glass feedstocks; volatile ruthenium trapping by solid adsorbents; irrigated baffle column dust scrubber. (author)

Centralized cement solidification technique for low-level radioactive wastes

International Nuclear Information System (INIS)

Matsuda, Masami; Nishi, Takashi; Izumida, Tatsuo; Tsuchiya, Hiroyuki.

1996-01-01

A centralized cement solidification system has been developed to enable a single facility to solidify such low-level radioactive wastes as liquid waste, spent ion exchange resin, incineration ash, and miscellaneous solid wastes. Since the system uses newly developed high-performance cement, waste loading is raised and deterioration of waste forms after land burial prevented. This paper describes the centralized cement solidification system and the features of the high-performance cement. Results of full-scale pilot plant tests are also shown from the viewpoint of industrial applicability. (author)

Utilization of coal fly ash in solidification of liquid radioactive waste from research reactor.

Science.gov (United States)

Osmanlioglu, Ahmet Erdal

2014-05-01

In this study, the potential utilization of fly ash was investigated as an additive in solidification process of radioactive waste sludge from research reactor. Coal formations include various percentages of natural radioactive elements; therefore, coal fly ash includes various levels of radioactivity. For this reason, fly ashes have to be evaluated for potential environmental implications in case of further usage in any construction material. But for use in solidification of radioactive sludge, the radiological effects of fly ash are in the range of radioactive waste management limits. The results show that fly ash has a strong fixing capacity for radioactive isotopes. Specimens with addition of 5-15% fly ash to concrete was observed to be sufficient to achieve the target compressive strength of 20 MPa required for near-surface disposal. An optimum mixture comprising 15% fly ash, 35% cement, and 50% radioactive waste sludge could provide the solidification required for long-term storage and disposal. The codisposal of radioactive fly ash with radioactive sludge by solidification decreases the usage of cement in solidification process. By this method, radioactive fly ash can become a valuable additive instead of industrial waste. This study supports the utilization of fly ash in industry and the solidification of radioactive waste in the nuclear industry.

Solidification characteristics and segregation behavior of a P-containing Ni-Fe-Cr-based alloy

Science.gov (United States)

Wang, Changshuai; Su, Haijun; Guo, YongAn; Guo, Jianting; Zhou, Lanzhang

2017-09-01

Solidification characteristics and segregation behavior of a P-containing Ni-Fe-Cr-based alloy, considered as boiler and turbine materials in 700 °C advanced ultra-supercritical coal-fired power plants, have been investigated by differential thermal analysis and directional solidification quenching technique. Results reveal that P decreases the solidus temperature, but only has negligible influence on liquidus temperature. After P was added, the solidification sequence has no apparent change, but the width of the mushy zone increases and dendritic structures become coarser. Moreover, P increases the amount and changes the morphology of MC carbide. Energy-dispersive spectroscopy analysis reveals that P has obvious influence on the segregation behavior of the constitute elements with equilibrium partition coefficients (ki) far away from unity, whereas has negligible effect on the constituent elements with ki close to unity and has more influence on the final stage of solidification than at early stage. The distribution profiles reveal that P atoms pile up ahead of the solid/liquid (S/L) interface and strongly segregate to the interdendritic liquid region. The influence of P on solidification characteristics and segregation behavior of Ni-Fe-Cr-based alloy could be attributed to the accumulation of P ahead of the S/L interface during solidification.

Transport processes in directional solidification and their effects on microstructure development

Science.gov (United States)

Mazumder, Prantik

The processing of materials with unique electronic, mechanical, optical and thermal properties plays a crucial role in modern technology. The quality of these materials depend strongly on the microstructures and the solute/dopant fields in the solid product, that are strongly influenced by the intricate coupling of heat and mass transfer and melt flow in the growth systems. An integrated research program is developed that include precisely characterized experiments and detailed physical and numerical modeling of the complex transport and dynamical processes. Direct numerical simulation of the solidification process is carried out that takes into account the unsteady thermo-solutal convection in the vertical Bridgman crystal growth system, and accurately models the thermal interaction between the furnace and the ampoule by appropriately using experimentally measured thermal profiles. The flow instabilities and transitions and the nonlinear evolution following the transitions are investigated by time series and flow pattern analysis. A range of complex dynamical behavior is predicted with increasing thermal Rayleigh number. The route to chaos appears as: steady convection --> transient mono-periodic --> transient bi-periodic --> transient quasiperiodic --> transient intermittent oscillation- relaxation --> stable intermittent oscillation-relaxation attractor. The spatio-temporal dynamics of the melt flow is found to be directly related to the spatial patterns observed experimentally in the solidified crystals. The application of the model to two phase Sn-Cd peritectic alloys showed that a new class of tree-like oscillating microstructure develops in the solid phase due to unsteady thermo-solutal convection in the liquid melt. These oscillating layered structures can give the illusion of band structures on a plane of polish. The model is applied to single phase solidification in the Al-Cu and Pb-Sn systems to characterize the effect of convection on the macroscopic

Solidification of low-level waste - a dilemma for the small user

International Nuclear Information System (INIS)

Harris, S.; Gilmore, A.

1980-01-01

The requirement that radioactive waste for sea disposal must be solidified by the originator is discussed. Attempts to solidify small quantities of radioactive waste such as contaminated oils and labelled benzyopyrene with other solvents are described. Encapsulation media tested were concrete and interior and exterior grade Polyfilla (a plaster and cellulose based filler). Problems were presented by the difficulty of mixing the materials and by the maximum uptake of solvents while still allowing solidification. In all cases a soft crumbling material resulted. It is concluded that solidification processing on a small scale does not make economic or scientific sense and that if solidification is necessary it would be better carried out as a national operation by collecting liquids from users. (U.K.)

Lower bound on the electroweak wall velocity from hydrodynamic instability

Energy Technology Data Exchange (ETDEWEB)

Mégevand, Ariel; Membiela, Federico Agustín; Sánchez, Alejandro D., E-mail: megevand@mdp.edu.ar, E-mail: membiela@mdp.edu.ar, E-mail: sanchez@mdp.edu.ar [IFIMAR (CONICET-UNMdP), Departamento de Física, Facultad de Ciencias Exactas y Naturales, Universidad Nacional de Mar del Plata, Deán Funes (7600) 3350 Mar del Plata (Argentina)

2015-03-01

The subsonic expansion of bubbles in a strongly first-order electroweak phase transition is a convenient scenario for electroweak baryogenesis. For most extensions of the Standard Model, stationary subsonic solutions (i.e., deflagrations) exist for the propagation of phase transition fronts. However, deflagrations are known to be hydrodynamically unstable for wall velocities below a certain critical value. We calculate this critical velocity for several extensions of the Standard Model and compare with an estimation of the wall velocity. In general, we find a region in parameter space which gives stable deflagrations as well as favorable conditions for electroweak baryogenesis.

Lower bound on the electroweak wall velocity from hydrodynamic instability

International Nuclear Information System (INIS)

Mégevand, Ariel; Membiela, Federico Agustín; Sánchez, Alejandro D.

2015-01-01

The subsonic expansion of bubbles in a strongly first-order electroweak phase transition is a convenient scenario for electroweak baryogenesis. For most extensions of the Standard Model, stationary subsonic solutions (i.e., deflagrations) exist for the propagation of phase transition fronts. However, deflagrations are known to be hydrodynamically unstable for wall velocities below a certain critical value. We calculate this critical velocity for several extensions of the Standard Model and compare with an estimation of the wall velocity. In general, we find a region in parameter space which gives stable deflagrations as well as favorable conditions for electroweak baryogenesis

Lower bound on the electroweak wall velocity from hydrodynamic instability

Energy Technology Data Exchange (ETDEWEB)

Mégevand, Ariel; Membiela, Federico Agustín; Sánchez, Alejandro D. [IFIMAR (CONICET-UNMdP), Departamento de Física, Facultad de Ciencias Exactas y Naturales, Universidad Nacional de Mar del Plata, Deán Funes (7600) 3350 Mar del Plata (Argentina)

2015-03-27

The subsonic expansion of bubbles in a strongly first-order electroweak phase transition is a convenient scenario for electroweak baryogenesis. For most extensions of the Standard Model, stationary subsonic solutions (i.e., deflagrations) exist for the propagation of phase transition fronts. However, deflagrations are known to be hydrodynamically unstable for wall velocities below a certain critical value. We calculate this critical velocity for several extensions of the Standard Model and compare with an estimation of the wall velocity. In general, we find a region in parameter space which gives stable deflagrations as well as favorable conditions for electroweak baryogenesis.

Five-dimensional imaging of freezing emulsions with solute effects.

Science.gov (United States)

Dedovets, Dmytro; Monteux, Cécile; Deville, Sylvain

2018-04-20

The interaction of objects with a moving solidification front is a common feature of many industrial and natural processes such as metal processing, the growth of single crystals, the cryopreservation of cells, or the formation of sea ice. Interaction of solidification fronts with objects leads to different outcomes, from total rejection of the objects to their complete engulfment. We imaged the freezing of emulsions in five dimensions (space, time, and solute concentration) with confocal microscopy. We showed that the solute induces long-range interactions that determine the solidification microstructure. The local increase of solute concentration enhances premelting, which controls the engulfment of droplets by the front and the evolution of grain boundaries. Freezing emulsions may be a good analog of many solidification systems where objects interact with a solidification interface. Copyright © 2018 The Authors, some rights reserved; exclusive licensee American Association for the Advancement of Science. No claim to original U.S. Government Works.

Light-Front Holography and the Light-Front Schrodinger Equation

Energy Technology Data Exchange (ETDEWEB)

Brodsky, Stanley J.; de Teramond, Guy

2012-08-15

One of the most important nonperturbative methods for solving QCD is quantization at fixed light-front time {tau} = t+z=c - Dirac's 'Front Form'. The eigenvalues of the light-front QCD Hamiltonian predict the hadron spectrum and the eigensolutions provide the light-front wavefunctions which describe hadron structure. More generally, we show that the valence Fock-state wavefunctions of the light-front QCD Hamiltonian satisfy a single-variable relativistic equation of motion, analogous to the nonrelativistic radial Schrodinger equation, with an effective confining potential U which systematically incorporates the effects of higher quark and gluon Fock states. We outline a method for computing the required potential from first principles in QCD. The holographic mapping of gravity in AdS space to QCD, quantized at fixed light-front time, yields the same light front Schrodinger equation; in fact, the soft-wall AdS/QCD approach provides a model for the light-front potential which is color-confining and reproduces well the light-hadron spectrum. One also derives via light-front holography a precise relation between the bound-state amplitudes in the fifth dimension of AdS space and the boost-invariant light-front wavefunctions describing the internal structure of hadrons in physical space-time. The elastic and transition form factors of the pion and the nucleons are found to be well described in this framework. The light-front AdS/QCD holographic approach thus gives a frame-independent first approximation of the color-confining dynamics, spectroscopy, and excitation spectra of relativistic light-quark bound states in QCD.

On the Importance of "Front-Side Mechanics" in Athletics Sprinting.

Science.gov (United States)

Haugen, Thomas; Danielsen, Jørgen; Alnes, Leif Olav; McGhie, David; Sandbakk, Øyvind; Ettema, Gertjan

2018-05-16

Practitioners have, for many years, argued that athletic sprinters should optimize front-side mechanics (leg motions occurring in front of the extended line through the torso) and minimize back-side mechanics. This study aimed to investigate if variables related to front- and back-side mechanics can be distinguished from other previously highlighted kinematic variables (spatiotemporal variables and variables related to segment configuration and velocities at touchdown) in how they statistically predict performance. A total of 24 competitive sprinters (age: 23.1 [3.4] y, height: 1.81 [0.06] m, body mass: 75.7 [5.6] kg, and 100-m personal best: 10.86 [0.22] s) performed two 20-m starts from block and 2 to 3 flying sprints over 20 m. Kinematics were recorded in 3D using a motion tracking system with 21 cameras at a 250 Hz sampling rate. Several front- and back-side variables, including thigh (r = .64) and knee angle (r = .51) at lift-off and maximal thigh extension (r = .66), were largely correlated (P mechanics were crucial for sprint performance among the investigated sprinters.

Retrofit of radwaste solidification systems in Spain

International Nuclear Information System (INIS)

Rorcillo, R.; Virzi, E.

1983-01-01

In order to meet current Spanish engineering criteria as well as to provide for likely future Spanish Regulatory requirements, utilities committed to a major policy change in the preferred radwaste solidification media. In the early 1970's Spanish utilities, following the United States experience, purchased inexpensive solidification systems which used urea formaldehyde (UF) as the binding matrix. By the late 1970's the Spanish utilities, seeing the deterioration of the UF position and slow progress toward its improvement, unilaterally changed their binding matrix to cement. This paper illustrates the implementation of this change at the ASCO Nuclear Plant. The problems of layout modifications, shortened delivery schedule and criteria unique for Spain are addressed. Also presented is the operating experience acquired during the pre-operational start-up of the ASCO I Radwaste System

Solidification processing of monotectic alloy matrix composites

Science.gov (United States)

Frier, Nancy L.; Shiohara, Yuh; Russell, Kenneth C.

1989-01-01

Directionally solidified aluminum-indium alloys of the monotectic composition were found to form an in situ rod composite which obeys a lambda exp 2 R = constant relation. The experimental data shows good agreement with previously reported results. A theoretical boundary between cellular and dendritic growth conditions was derived and compared with experiments. The unique wetting characteristics of the monotectic alloys can be utilized to tailor the interface structure in metal matrix composites. Metal matrix composites with monotectic and hypermonotectic Al-In matrices were made by pressure infiltration, remelted and directionally solidified to observe the wetting characteristics of the alloys as well as the effect on structure of solidification in the constrained field of the fiber interstices. Models for monotectic growth are modified to take into account solidification in these constrained fields.

Linear Stability of Binary Alloy Solidification for Unsteady Growth Rates

Science.gov (United States)

Mazuruk, K.; Volz, M. P.

2010-01-01

An extension of the Mullins and Sekerka (MS) linear stability analysis to the unsteady growth rate case is considered for dilute binary alloys. In particular, the stability of the planar interface during the initial solidification transient is studied in detail numerically. The rapid solidification case, when the system is traversing through the unstable region defined by the MS criterion, has also been treated. It has been observed that the onset of instability is quite accurately defined by the "quasi-stationary MS criterion", when the growth rate and other process parameters are taken as constants at a particular time of the growth process. A singular behavior of the governing equations for the perturbed quantities at the constitutional supercooling demarcation line has been observed. However, when the solidification process, during its transient, crosses this demarcation line, a planar interface is stable according to the linear analysis performed.

Solidification Mapping of a Nickel Alloy 718 Laboratory VAR Ingot

Science.gov (United States)

Watt, Trevor J.; Taleff, Eric M.; Lopez, Felipe; Beaman, Joe; Williamson, Rodney

The solidification microstructure of a laboratory-scale Nickel alloy 718 vacuum arc remelted (VAR) ingot was analyzed. The cylindrical, 210-mm-diameter ingot was sectioned along a plane bisecting it length-wise, and this mid-plane surface was ground and etched using Canada's reagent to reveal segregation contrast. Over 350 photographs were taken of the etched mid-plane surface and stitched together to form a single mosaic image. Image data in the resulting mosaic were processed using a variety of algorithms to extract quantities such as primary dendrite orientation, primary dendrite arm spacing (PDAS), and secondary dendrite arm spacing (SDAS) as a function of location. These quantities were used to calculate pool shape and solidification rate during solidification using existing empirical relationships for Nickel Alloy 718. The details and outcomes of this approach, along with the resulting comparison to experimental processing conditions and computational models, are presented.

Analysis of weld solidification cracking in cast nickel aluminide alloys

International Nuclear Information System (INIS)

Santella, M.L.; Feng, Z.

1995-01-01

A study of the response of several nickel aluminide alloys to SigmaJig testing was done to examine their weld solidification cracking behavior and the effect of Zr concentration. The alloys were based on the Ni-8Al-7.7Cr-1.5Mo-0.003B wt% composition and contained Zr concentrations of 3, 4.5, and 6 wt%. Vacuum induction melted ingots with a diameter of 2.7 in and weight about 18 lb were made of each alloy, and were used to make 2 x 2 x 0.030 in specimens for the Sigmajig test. The gas tungsten arc welds were made at travel speeds of 10, 20, and 30 ipm with heat inputs of 2--2.5 kJ/in. When an arc was established before traveling onto the test specimen centerline cracking was always observed. This problem was overcome by initiating the arc directly on the specimens. Using this approach, the 3 wt% Zr alloy withstood an applied stress of 24 ksi without cracking at a welding speed of 10 ipm. This alloy cracked at 4 ksi applied at 20 ipm, and with no applied load at 30 ipm. Only limited testing was done on the remaining alloys, but the results indicate that resistance to solidification cracking increases with Zr concentration. Zirconium has limited solid solubility and segregates strongly to interdendritic regions during solidification where it forms a Ni solid solution-Ni 5 Zr eutectic. The volume fraction of the eutectic increases with Zr concentration. The solidification cracking behavior of these alloys is consistent with phenomenological theory, and is discussed in this context. The results from SigmaJig testing are analyzed using finite element modeling of the development of mechanical strains during solidification of welds. Experimental data from the test substantially agree with recent analysis results

Rapid Convergence and Subduction at the Intersections of Fronts

Science.gov (United States)

D'Asaro, E. A.

2016-12-01

An array of 300 surface drifters drogued to follow the top 0.6m of the ocean were deployed in the northern Gulf of Mexico near the Deep Water Horizon spill site in January of 2016. As expected, the array spread from its initial 15x15km scale with the second moment increasing at a rate roughly consistent with historical dispersion curves. More surprisingly, a large fraction of the drifters accumulated within a km-scale submesoscale eddy and grouped into clusters often only a few meters apart. This occurred due to surface convergence, as opposed to purely confluence, with convergence rates of many f feeding downward-going subduction zones with vertical velocities of a few centimeters per second. These convergences preferentially occurred at density fronts and in particular at junctions of density fronts on the periphery of submesoscale eddies. These observations complement the traditional view of lateral dispersion of surface particles by mesoscale eddies with a competing submesocale convergence and provide direct observations of the strong vertical exchanges associated with submesoscale eddies and fronts.

Multiscale modeling of alloy solidification using a database approach

Science.gov (United States)

Tan, Lijian; Zabaras, Nicholas

2007-11-01

A two-scale model based on a database approach is presented to investigate alloy solidification. Appropriate assumptions are introduced to describe the behavior of macroscopic temperature, macroscopic concentration, liquid volume fraction and microstructure features. These assumptions lead to a macroscale model with two unknown functions: liquid volume fraction and microstructure features. These functions are computed using information from microscale solutions of selected problems. This work addresses the selection of sample problems relevant to the interested problem and the utilization of data from the microscale solution of the selected sample problems. A computationally efficient model, which is different from the microscale and macroscale models, is utilized to find relevant sample problems. In this work, the computationally efficient model is a sharp interface solidification model of a pure material. Similarities between the sample problems and the problem of interest are explored by assuming that the liquid volume fraction and microstructure features are functions of solution features extracted from the solution of the computationally efficient model. The solution features of the computationally efficient model are selected as the interface velocity and thermal gradient in the liquid at the time the sharp solid-liquid interface passes through. An analytical solution of the computationally efficient model is utilized to select sample problems relevant to solution features obtained at any location of the domain of the problem of interest. The microscale solution of selected sample problems is then utilized to evaluate the two unknown functions (liquid volume fraction and microstructure features) in the macroscale model. The temperature solution of the macroscale model is further used to improve the estimation of the liquid volume fraction and microstructure features. Interpolation is utilized in the feature space to greatly reduce the number of required

Solidification of high-level radioactive wastes. Final report

International Nuclear Information System (INIS)

1979-06-01

A panel on waste solidification was formed at the request of the Nuclear Regulatory Commission to study the scientific and technological problems associated with the conversion of liquid and semiliquid high-level radioactive wastes into a stable form suitable for transportation and disposition. Conclusions reached and recommendations made are as follows. Many solid forms described in this report could meet standards as stringent as those currently applied to the handling, storage, and transportation of spent fuel assemblies. Solid waste forms should be selected only in the context of the total radioactive waste management system. Many solid forms are likely to be satisfactory for use in an appropriately designed system, The current United States policy of deferring the reprocessing of commercial reactor fuel provides additional time for R and D solidification technology for this class of wastes. Defense wastes which are relatively low in radioactivity and thermal power density can best be solidified by low-temperature processes. For solidification of fresh commercial wastes that are high in specific activity and thermal power density, the Panel recommends that, in addition to glass, the use of fully-crystalline ceramics and metal-matrix forms be actively considered. Preliminary analysis of the characteristics of spent fuel pins indicates that they may be eligible for consideration as a waste form. Because the differences in potential health hazards to the public resulting from the use of various solid form and disposal options are likely to be small, the Panel concludes that cost, reliability, and health hazards to operating personnel will be major considerations in choosing among the options that can meet safety requiremens. The Panel recommends that responsibility for all radioactive waste management operations (including solidification R and D) should be centralized

Solidification process for toxic and hazardous wastes. Second part: Cement solidification matrices; Inertizzazione di rifiuti tossici e nocivi (RTN). Parte seconda: Inertizzazione in matrici cementizie

Energy Technology Data Exchange (ETDEWEB)

Donato, A; Arcuri, L; Dotti, M; Pace, A; Pietrelli, L; Ricci, G [ENEA - Dipartimento Ciclo del Combustibile, Centro Ricerche Energia, Casaccia (Italy); Basta, M; Cali, V; Pagliai, V [ENEA - Dipartimento Ciclo del Combustibile, Centro Ricerche Energia, Saluggia (Italy)

1989-05-15

This paper reports the second part of a general study carried out at the Nuclear Fuel Division aiming at verifying the possible application of the radioactive waste solidification processes to industrial hazardous wastes (RTN). The cement solidification of several RTN types has been taken into consideration, both from the technical and from the economic point of view. After a short examination of the Italian juridical and economical situation in the field, which demonstrates the need of the RTN solidification, the origin and characteristics of the RTN considered in the study and directly provided by the producing industries are reviewed. The laboratory experimental results of the cementation of RTN produced by gold manufacturing industries and by galvanic industries are reported. The cementation process can be considered a very effective mean for reducing both the RTN management costs and the environmental impact of RTN disposal. (author)

Solidification of radioactive waste in a cement/lime mixture

International Nuclear Information System (INIS)

Zhou, H.; Colombo, P.

1984-01-01

The suitability of a cement/lime mixture for use as a solidification agent for different types of wastes was investigated. This work includes studies directed towards determining the wasted/binder compositional field over which successful solidification occurs with various wastes and the measurement of some of the waste from properties relevant to evaluating the potential for the release of radionuclides to the environment. In this study, four types of low-level radioactive wastes were simulated for incorporation into a cement/lime mixture. These were boric acid waste, sodium sulfate wastes, aion exchange resins and incinerator ash. 7 references, 3 figures, 2 tables

Instability of an infiltration-driven dissolution-precipitation front with a nonmonotonic porosity profile

Science.gov (United States)

Kondratiuk, Paweł; Dutka, Filip; Szymczak, Piotr

2016-04-01

Infiltration of a rock by an external fluid very often drives it out of chemical equilibrium. As a result, alteration of the rock mineral composition occurs. It does not however proceed uniformly in the entire rock volume. Instead, one or more reaction fronts are formed, which are zones of increased chemical activity, separating the altered (product) rock from the yet unaltered (primary) one. The reaction fronts propagate with velocities which are usually much smaller than those of the infiltrating fluid. One of the simplest examples of such alteration is the dissolution of some of the minerals building the primary rock. For instance, calcium carbonate minerals in the rock matrix can be dissolved by infiltrating acidic fluids. In such a case the product rock has higher porosity and permeability than the primary one. Due to positive feedbacks between the reactant transport, fluid flow, and porosity generation, the reaction fronts in porosity-generating replacement systems are inherently unstable. An arbitrarily small protrusion of the front gets magnified and develops into a highly porous finger-like or funnel-like structure. This feature of dissolution fronts, dubbed the "reactive-infiltration instability" [1], is responsible for the formation of a number of geological patterns, such as solution pipes or various karst forms. It is also of practical importance, since spontaneous front breakup and development of localized highly porous flow paths (a.k.a. "wormholes") is favourable by petroleum engineers, who apply acidization to oil-bearing reservoirs in order to increase their permeability. However, more complex chemical reactions might occur during infiltration of a rock by a fluid. In principle, the products of dissolution might react with other species present either in the fluid or in the rock and reprecipitate [2]. The dissolution and precipitation fronts develop and and begin to propagate with equal velocities, forming a single dissolution-precipitation front

INEL studies concerning solidification of low-level waste in cement

International Nuclear Information System (INIS)

Mandler, J.W.

1989-01-01

The Idaho National Engineering Laboratory (INEL) has performed numerous studies addressing issues concerning the solidification of low-level radioactive waste in cement. These studies have been performed for both the Nuclear Regulatory Commission (NRC) and the Department of Energy (DOE). This short presentation will only outline the major topics addressed in some of these studies, present a few conclusions, and identify some of the technical concerns we have. More details of the work and pertinent results will be given in the Working Group sessions. The topics that have been addressed at the INEL which are relevant to this Workshop include (1) solidification of ion-exchange resins and evaporator waste in cement at commercial nuclear power plants, (2) leachability and compressive strength of power plant waste solidified in cement, (3) suggested guidelines for preparation of a solid waste process control program (PCP), (4) cement solidification of EPICOR-II resin wastes, and (5) performance testing of cement-solidified EPICOR-II resin wastes

Propagating gene expression fronts in a one-dimensional coupled system of artificial cells

Science.gov (United States)

Tayar, Alexandra M.; Karzbrun, Eyal; Noireaux, Vincent; Bar-Ziv, Roy H.

2015-12-01

Living systems employ front propagation and spatiotemporal patterns encoded in biochemical reactions for communication, self-organization and computation. Emulating such dynamics in minimal systems is important for understanding physical principles in living cells and in vitro. Here, we report a one-dimensional array of DNA compartments in a silicon chip as a coupled system of artificial cells, offering the means to implement reaction-diffusion dynamics by integrated genetic circuits and chip geometry. Using a bistable circuit we programmed a front of protein synthesis propagating in the array as a cascade of signal amplification and short-range diffusion. The front velocity is maximal at a saddle-node bifurcation from a bistable regime with travelling fronts to a monostable regime that is spatially homogeneous. Near the bifurcation the system exhibits large variability between compartments, providing a possible mechanism for population diversity. This demonstrates that on-chip integrated gene circuits are dynamical systems driving spatiotemporal patterns, cellular variability and symmetry breaking.

In situ observations of graphite formation during solidification of cast iron

DEFF Research Database (Denmark)

Bjerre, Mathias Karsten

solidification and growth continues throughout solid state cooling and the eutectoid transformation. Years of research have greatly improved the understanding of the basic mechanisms that control graphite growth as well as the ability to control graphite morphology during industrial production of cast components......, the solidification of cast iron is studied with focus on formation and growth of spheroidal graphite. To this end, an experiment is conducted at the Diamond Light Source synchrotron facility in Harwell, UK: Employing an environmental cell devel-oped at the Manchester X-ray Imaging Facility at the University...... state growth presented in the present thesis. From the analysis it is clear that the presented data is of an unprecedented quality and that it represents a solid basis for validation of future models. Solidification simulations of a ductile cast iron component highlights the importance of the nucleation...

Physicochemical characterization of solidification agents used and products formed with radioactive wastes at LWR nuclear power plants

International Nuclear Information System (INIS)

Kibbey, A.H.; Godbee, H.W.

1978-01-01

Solidification of evaporator concentrates, filter sludges, and spent ion exchange resins used in LWR streams is discussed. The introduction of solidification agents to immobilize these sludges and resins can increase the volume of these wastes by a factor of slightly over 1 to greater than 2, depending on the binder chosen. The agents and methods used or proposed for use in solidification of LWR power plant wastes are generally suitable for treating most of the other-than-high-level wastes generated throughout the entire fuel cycle. Among the solidification agents most commonly used or suggested for use are the inorganic cements and organic plastics, which are listed and compared. A summary of considerations important in choosing a solidification agent is presented tabularly

Cement solidification of spent ion exchange resins produced by the nuclear industry

International Nuclear Information System (INIS)

Jaouen, C.; Vigreux, B.

1988-01-01

Cement solidification technology has been applied to spent ion exchange resins for many years in countries throughout the world (at reactors, research centers and spent fuel reprocessing plants). Changing specifications for storage of radioactive waste have, however, confronted the operators of such facilities with a number of problems. Problems related both to the cement solidification process (water/cement/resin interactions and chemical interactions) and to its utilization (mixing, process control, variable feed composition, etc.) have often led waste producers to prefer other, polymer-based processes, which are very expensive and virtually incompatible with water. This paper discusses research on cement solidification of ion exchange resins since 1983 and the development of application technologies adapted to nuclear service conditions and stringent finished product quality requirements

Long-lived magnetism from solidification-driven convection on the pallasite parent body

DEFF Research Database (Denmark)

Bryson, James F.J.; Nichols, Claire I. O.; Herrero-Albillos, Julia

2015-01-01

of long-lived magnetic activity on the pallasite parent body, capturing the decay and eventual shutdown of the magnetic field as core solidification completed.We demonstrate that magnetic activity driven by progressive solidification of an inner core is consistent with our measuredmagnetic field......Palaeomagnetic measurements of meteorites suggest that, shortly after the birth of the Solar System, themolten metallic cores ofmany small planetary bodies convected vigorously and were capable of generating magnetic fields. Convection on these bodies is currently thought to have been thermally...... characteristics and cooling rates. Solidification-driven convectionwas probably commonamong small body cores, and, in contrast to thermally driven convection, will have led to a relatively late (hundreds of millions of years after accretion), long-lasting, intense and widespread epoch of magnetic activity among...

Integral solution of equiaxed solidification with an interface kinetics model for nuclear waste management

International Nuclear Information System (INIS)

Naterer, G.F.

1996-01-01

In this paper, a one-dimensional analysis of energy and species transport during binary dendritic solidification is presented and compared to experimental results. The paper's objective is a continuation of previous studies of solidification control for the waste management of nuclear materials in the underground disposal concept. In the present analysis, interface kinetics at the solid - liquid interface accounts for recalescent thermal behaviour during solidification. The theoretical results were compared to available experimental results and the agreement appears fair although some discrepancies have been attributed to uncertainties with thermophysical properties. (author)

Solidification of ion exchange resin wastes

International Nuclear Information System (INIS)

1982-08-01

Solidification media investigated included portland type I, portland type III and high alumina cements, a proprietary gypsum-based polymer modified cement, and a vinyl ester-styrene thermosetting plastic. Samples formulated with hydraulic cement were analyzed to investigate the effects of resin type, resin loading, waste-to-cement ratio, and water-to-cement ratio. The solidification of cation resin wastes with portland cement was characterized by excessive swelling and cracking of waste forms, both after curing and during immersion testing. Mixed bed resin waste formulations were limited by their cation component. Additives to improve the mechanical properties of portland cement-ion exchange resin waste forms were evaluated. High alumina cement formulations dislayed a resistance to deterioration of mechanical integrity during immersion testing, thus providing a significant advantage over portland cements for the solidification of resin wastes. Properties of cement-ion exchange resin waste forms were examined. An experiment was conducted to study the leachability of 137 Cs, 85 Sr, and 60 Co from resins modified in portland type III and high alumina cements. The cumulative 137 Cs fraction release was at least an order of magnitude greater than that of either 85 Sr or 60 Co. Release rates of 137 Cs in high alumina cement were greater than those in portland III cement by a factor of two.Compressive strength and leach testing were conducted for resin wastes solidified with polymer-modified gypsum based cement. 137 Cs, 85 Sr, and 60 Co fraction releases were about one, two and three orders of magnitude higher, respectively, than in equivalent portland type III cement formulations. As much as 28.6 wt % dry ion exchange resin was successfully solidified using vinyl ester-styrene compared with a maximum of 25 wt % in both portland and gypsum-based cement

Processing and solidification of Savannah River Plant high-level waste

International Nuclear Information System (INIS)

Kelley, J.A.

1981-01-01

The entire flowsheet for processing and solidification of Savannah River Plant (SRP) high-level wastes has been demonstrated. A new small-scale integrated pilot plant is operating with actual radioactive wastes, and large-scale equipment is being demonstrated with nonradioactive simulated wastes. Design of a full-scale waste solidification plant is in progress. Plant construction is expected to begin in 1983, and startup is anticipated in 1988. The plant will poduce about 500 cans of glass per year with each can containing about 1.5 tons of glass

Some techniques for the solidification of radioactive wastes in concrete

International Nuclear Information System (INIS)

Colombo, P.; Neilson, R. Jr.

1976-06-01

Some techniques for the solidification of radioactive wastes in concrete are discussed. The sources, storage, volume reduction, and solidification of liquid wastes at Brookhaven National Laboratory (BNL) using the cement-vermiculite process is described. Solid waste treatment, shipping containers, and off-site shipments of solid wastes at BNL are also considered. The properties of low-heat-generating, high-level wastes, simulating those in storage at the Savannah River Plant (SRP), solidified in concrete were determined. Polymer impregnation was found to further decrease the leachability and improve the durability of these concrete waste forms

Closed solutions to a differential-difference equation and an associated plate solidification problem.

Science.gov (United States)

Layeni, Olawanle P; Akinola, Adegbola P; Johnson, Jesse V

2016-01-01

Two distinct and novel formalisms for deriving exact closed solutions of a class of variable-coefficient differential-difference equations arising from a plate solidification problem are introduced. Thereupon, exact closed traveling wave and similarity solutions to the plate solidification problem are obtained for some special cases of time-varying plate surface temperature.

NPP radioactive waste processing and solidification

International Nuclear Information System (INIS)

Nikiforov, A.S.; Polyakov, A.S.; Zakharova, K.P.

1983-01-01

The problems of proce-sing NPP intermediate level- and low-level liquid radioactive wastes (LRW) are considered. Various methods are compared of LWR solidification on the base of bituminization, cement grouting and inclusion into synthetic resins. It is concluded that the considered methods ensure radioactive radionuclides effluents into open hydronetwork at the level below the sanitary, standards

ENGINEERING BULLETIN: SOLIDIFICATION/STABILIZATION OF ORGANICS AND INORGANICS

Science.gov (United States)

Solidification refers to techniques that encapsulate hazardous waste into a solid material of high structural integrity. Encapsulation involves either fine waste particles (microencapsulation) or a large block or container of wastes (macroencapsulation). Stabilization refe...

Interferometric measurements of a dendritic growth front solutal diffusion layer

Science.gov (United States)

Hopkins, John A.; Mccay, T. D.; Mccay, Mary H.

1991-01-01

An experimental study was undertaken to measure solutal distributions in the diffusion layer produced during the vertical directional solidification (VDS) of an ammonium chloride - water (NH4Cl-H2O) solution. Interferometry was used to obtain concentration measurements in the 1-2 millimeter region defining the diffusion layer. These measurements were fitted to an exponential form to extract the characteristic diffusion parameter for various times after the start of solidification. The diffusion parameters are within the limits predicted by steady state theory and suggest that the effective solutal diffusivity is increasing as solidification progresses.

Solidification and performance of cement doped with phenol

International Nuclear Information System (INIS)

Vipulanandan, C.; Krishnan, S.

1991-01-01

Treating mixed hazardous wastes using the solidification/stabilization technology is becoming a critical element in waste management planning. The effect of phenol, a primary constituent in many hazardous wastes, on the setting and solidification process of Type I Portland cement was evaluated. The leachability of phenol from solidified cement matrix (TCLP test) and changes in mechanical properties were studied after curing times up to 28 days. The changes in cement hydration products due to phenol were studied using the X-ray diffraction (XRD) powder technique. Results show that phenol interferes with initial cement hydration by reducing the formation of calcium hydroxide and also reduces the compressive strength of cement. A simple model has been proposed to quantify the phenol leached from the cement matrix during the leachate test

Continuous Solidification of Immiscible Alloys and Microstructure Control

Science.gov (United States)

Jiang, Hongxiang; Zhao, Jiuzhou

2018-05-01

Immiscible alloys have aroused considerable interest in last few decades due to their excellent physical and mechanical characteristics as well as potential industrial applications. Up to date, plenty of researches have been carried out to investigate the solidification of immiscible alloys on the ground or in space and great progress has been made. It is demonstrated that the continuous solidification technique have great future in the manufacturing of immiscible alloys, it also indicates that the addition of surface active micro-alloying or inoculants for the nucleation of the minority phase droplets and proper application of external fields, e.g., static magnetic field, electric current, microgravity field, etc. may promote the formation of immiscible alloys with an expected microstructure. The objective of this article is to review the research work in this field.

Metastable and unstable cellular solidification of colloidal suspensions

Science.gov (United States)

Deville, Sylvain; Maire, Eric; Bernard-Granger, Guillaume; Lasalle, Audrey; Bogner, Agnès; Gauthier, Catherine; Leloup, Jérôme; Guizard, Christian

2009-12-01

Colloidal particles are often seen as big atoms that can be directly observed in real space. They are therefore becoming increasingly important as model systems to study processes of interest in condensed-matter physics such as melting, freezing and glass transitions. The solidification of colloidal suspensions has long been a puzzling phenomenon with many unexplained features. Here, we demonstrate and rationalize the existence of instability and metastability domains in cellular solidification of colloidal suspensions, by direct in situ high-resolution X-ray radiography and tomography observations. We explain such interface instabilities by a partial Brownian diffusion of the particles leading to constitutional supercooling situations. Processing under unstable conditions leads to localized and global kinetic instabilities of the solid/liquid interface, affecting the crystal morphology and particle redistribution behaviour.

Redox fronts

International Nuclear Information System (INIS)

Chapman, N.; McKinley, I.; Shea, M.; Smellie, J.

1993-01-01

This article describes the investigations of redox fronts performed at the Osamu Utsumi mine. Results obtained by modelling groups on the rate of movement of the redox fronts and on the chemical reactions involved are discussed. Some of the most important rockwater interactions which occur at redox fronts can be modelled reasonably well but the complex redox chemistry of elements like sulphur is poorly simulated. The observed enrichment of many trace elements close to the redox fronts could be of significance for high-level waste repositories, but cannot be quantified by existing models. (author) 6 figs., 1 tab

Effect of Chemical Composition on Susceptibility to Weld Solidification Cracking in Austenitic Weld Metal

Science.gov (United States)

Kadoi, Kota; Shinozaki, Kenji

2017-12-01

The influence of the chemical composition, especially the niobium content, chromium equivalent Creq, and nickel equivalent Nieq, on the weld solidification cracking susceptibility in the austenite single-phase region in the Schaeffler diagram was investigated. Specimens were fabricated using the hot-wire laser welding process with widely different compositions of Creq, Nieq, and niobium in the region. The distributions of the susceptibility, such as the crack length and brittle temperature range (BTR), in the Schaeffler diagram revealed a region with high susceptibility to solidification cracking. Addition of niobium enhanced the susceptibility and changed the distribution of the susceptibility in the diagram. The BTR distribution was in good agreement with the distribution of the temperature range of solidification (Δ T) calculated by solidification simulation based on Scheil model. Δ T increased with increasing content of alloying elements such as niobium. The distribution of Δ T was dependent on the type of alloying element owing to the change of the partitioning behavior. Thus, the solidification cracking susceptibility in the austenite single-phase region depends on whether the alloy contains elements. The distribution of the susceptibility in the region is controlled by the change in Δ T and the segregation behavior of niobium with the chemical composition.

Particle Trapping and Banding in Rapid Colloidal Solidification

KAUST Repository

Elliott, J. A. W.; Peppin, S. S. L.

2011-01-01

We derive an expression for the nonequilibrium segregation coefficient of colloidal particles near a moving solid-liquid interface. The resulting kinetic phase diagram has applications for the rapid solidification of clay soils, gels, and related

Microstructure of rapidly solidified materials

Science.gov (United States)

Jones, H.

1984-07-01

The basic features of rapidly solidified microstructures are described and differences arising from alternative processing strategies are discussed. The possibility of achieving substantial undercooling prior to solidification in processes such as quench atomization and chill block melt spinning can give rise to striking microstructural transitions even when external heat extraction is nominally Newtonian. The increased opportunity in laser and electron beam surface melting for epitaxial growth on the parent solid at an accelerating rate, however, does not exclude the formation of nonequilibrium phases since the required undercooling can be locally attained at the solidification front which is itself advancing at a sufficiently high velocity. The effects of fluid flow indicated particularly in melt spinning and surface melting are additional to the transformational and heat flow considerations that form the present basis for interpretation of such microstructural effects.

Formation of Nitrogen Bubbles During Solidification of Duplex Stainless Steels

Science.gov (United States)

Dai, Kaiju; Wang, Bo; Xue, Fei; Liu, Shanshan; Huang, Junkai; Zhang, Jieyu

2018-04-01

The nucleation and growth of nitrogen bubbles for duplex stainless steels are of great significance for the formation mechanism of bubbles during solidification. In the current study, numerical method and theoretical analysis of formula derivation were used to study the formation of nitrogen bubbles during solidification. The critical sizes of the bubble for homogeneous nucleation and heterogeneous nucleation at the solid-liquid interface during solidification were derived theoretically by the classical nucleation theory. The results show that the calculated values for the solubility of nitrogen in duplex stainless steel are in good agreement with the experimental values which are quoted by references: for example, when the temperature T = 1823 K and the nitrogen partial pressure P_{{N2 }} = 40P^{Θ} , the calculated value (0.8042 wt pct) for the solubility of Fe-12Cr alloy nitrogen in molten steel is close to the experimental value (0.780 wt pct). Moreover, the critical radii for homogeneous nucleation and heterogeneous nucleation are identical during solidification. On the one hand, with the increasing temperature or the melt depth, the critical nucleation radius of bubbles at the solid-liquid interface increases, but the bubble growth rate decreases. On the other hand, with the decreasing initial content of nitrogen or the cooling rate, the critical nucleation radius of bubbles at the solid-liquid interface increases, but the bubble growth rate decreases. Furthermore, when the melt depth is greater than the critical depth, which is determined by the technological conditions, the change in the Gibbs free energy for the nucleation is not conducive enough to form new bubbles.

Solidification of liquid concentrate and solid waste generated as by-products of the liquid radwaste treatment systems in light-water reactors

International Nuclear Information System (INIS)

Neilson, R.M. Jr.; Colombo, P.

1977-01-01

The treatment of liquid concentrate and solid waste produced in light-water reactors as by-products of liquid radwaste treatment systems consists of five basic operations: waste collection, waste pretreatment, solidification agent handling, mixing/packaging (solidification) and waste package handling. This paper will concern itself primarily with the solidification operation, however, the other operations enumerated as well as the types of wastes treated and their origins will be briefly described, especially with regards to their effects on solidification. During solidification, liquid concentrate and solid wastes are incorporated with a solidification agent to form a monolithic, free-standing solid. The basic solidification agent types either currently used in the United States or proposed for use include absorbants, hydraulic cement, urea-formaldehyde, other polymer systems, and bitumen. The operation, formulations and limitations of these agents as used for radwaste solidification will be discussed. Properties relevant to the evaluation of solidified waste forms will be identified and relative comparisons made for wastes solidified by various processes

UNDERWATER STROKE KINEMATICS DURING BREATHING AND BREATH-HOLDING FRONT CRAWL SWIMMING

Directory of Open Access Journals (Sweden)

Nickos Vezos

2007-03-01

Full Text Available The aim of the present study was to determine the effects of breathing on the three - dimensional underwater stroke kinematics of front crawl swimming. Ten female competitive freestyle swimmers participated in the study. Each subject swam a number of front crawl trials of 25 m at a constant speed under breathing and breath-holding conditions. The underwater motion of each subject's right arm was filmed using two S-VHS cameras, operating at 60 Hz, which were positioned behind two underwater viewing windows. The spatial coordinates of selected points were calculated using the DLT procedure with 30 control points and after the digital filtering of the raw data with a cut-off frequency of 6 Hz, the hand's linear displacements and velocities were calculated. The results revealed that breathing caused significantly increases in the stroke duration (t9 = 2.764; p < 0.05, the backward hand displacement relative to the water (t9 = 2.471; p<0.05 and the lateral displacement of the hand in the X - axis during the downsweep (t9 = 2.638; p < 0.05. On the contrary, the peak backward hand velocity during the insweep (t9 = 2.368; p < 0.05 and the displacement of the hand during the push phase (t9 = -2.297; p < 0.05 were greatly reduced when breathing was involved. From the above, it was concluded that breathing action in front crawl swimming caused significant modifications in both the basic stroke parameters and the overall motor pattern were, possibly due to body roll during breathing

Effect of grain refiner on intermetallic phase formation in directional solidification of 6xxx series wrought Al alloys

Energy Technology Data Exchange (ETDEWEB)

Sha, G.; O' Reilly, K.; Cantor, B. [Oxford Univ. (United Kingdom). Centre for Adv. Mat. and Composites; Hamerton, R.; Worth, J.

2000-07-01

The effect of a grain refiner on the formation of intermetallic phases in a directionally solidified (Bridgman grown) model 6xxx series wrought Al alloy has been investigated using X-ray diffractometry (XRD), transmission electron microscopy (TEM) and differential scanning calorimetry (DSC). A base alloy with and without Al-Ti-B grain refiner was directionally solidified in a Bridgman furnace at growth velocities in the range of 5-120 mm/min. In both cases, the Fe-containing intermetallic phases present were found to be mainly {alpha}-AlFeSi and {beta}-AlFeSi. However, in the alloy with grain refiner solidified at 5mm/min, Al{sub 13}Fe{sub 4} was also observed. Quantitative XRD results indicated that the addition of Al-Ti-B grain refiner has a strong influence on the relative quantities of intermetallic phases forming during solidification at different growth velocities, which was also confirmed by TEM observations. TEM observations also show that depending on where the {beta}-AlFeSi particles solidified e.g. grain boundaries or triple grain junctions, the size and morphology of the particles may change dramatically. TiB{sub 2} particles were observed to nucleate {beta}-AlFeSi at low and high growth velocities in the 6xxx series Al alloys. (orig.)

Species redistribution during solidification of nuclear fuel waste metal castings

Energy Technology Data Exchange (ETDEWEB)

Naterer, G F; Schneider, G E [Waterloo Univ., ON (Canada)

1994-12-31

An enthalpy-based finite element model and a binary system species redistribution model are developed and applied to problems associated with solidification of nuclear fuel waste metal castings. Minimal casting defects such as inhomogeneous solute segregation and cracks are required to prevent container corrosion and radionuclide release. The control-volume-based model accounts for equilibrium solidification for low cooling rates and negligible solid state diffusion for high cooling rates as well as intermediate conditions. Test problems involving nuclear fuel waste castings are investigated and correct limiting cases of species redistribution are observed. (author). 11 refs., 1 tab., 13 figs.

Micromechanical modeling of stress-induced strain in polycrystalline Ni–Mn–Ga by directional solidification

International Nuclear Information System (INIS)

Zhu, Yuping; Shi, Tao; Teng, Yao

2015-01-01

Highlights: • A micromechanical model of directional solidification Ni–Mn–Ga is developed. • The stress–strain curves in different directions are tested. • The martensite Young’s moduli in different directions are predicted. • The macro reorientation strains in different directions are investigated. - Abstract: Polycrystalline ferromagnetic shape memory alloy Ni–Mn–Ga produced by directional solidification possess unique properties. Its compressive stress–strain behaviors in loading–unloading cycle show nonlinear and anisotropic. Based on the self-consistent theory and thermodynamics principle, a micromechanical constitutive model of polycrystalline Ni–Mn–Ga by directional solidification is developed considering the generating mechanism of the macroscopic strain and anisotropy. Then, the stress induced strains at different angles to solidification direction are calculated, and the results agree well with the experimental data. The predictive curves of martensite Young’s modulus and macro reorientation strain in different directions are investigated. It may provide theoretical guidance for the design and use of ferromagnetic shape memory alloy

Current high-level waste solidification technology

International Nuclear Information System (INIS)

Bonner, W.F.; Ross, W.A.

1976-01-01

Technology has been developed in the U.S. and abroad for solidification of high-level waste from nuclear power production. Several processes have been demonstrated with actual radioactive waste and are now being prepared for use in the commercial nuclear industry. Conversion of the waste to a glass form is favored because of its high degree of nondispersibility and safety

Simulation of Microstructure during Laser Rapid Forming Solidification Based on Cellular Automaton

Directory of Open Access Journals (Sweden)

Zhi-jian Wang

2014-01-01

Full Text Available The grain microstructure of molten pool during the solidification of TC4 titanium alloy in the single point laser cladding was investigated based on the CAFE model which is the cellular automaton (CA coupled with the finite element (FE method. The correct temperature field is the prerequisite for simulating the grain microstructure during the solidification of the molten pool. The model solves the energy equation by the FE method to simulate the temperature distribution in the molten pool of the single point laser cladding. Based on the temperature field, the solidification microstructure of the molten pool is also simulated with the CAFE method. The results show that the maximum temperature in the molten pool increases with the laser power and the scanning rate. The laser power has a larger influence on the temperature distribution of the molten pool than the scanning rate. During the solidification of the molten pool, the heat at the bottom of the molten pool transfers faster than that at the top of the molten pool. The grains rapidly grow into the molten pool, and then the columnar crystals are formed. This study has a very important significance for improving the quality of the structure parts manufactured through the laser cladding forming.

Experimental and Theoretical Investigations of the Solidification of Eutectic Al-Si Alloy

Science.gov (United States)

Sen, S.; Catalina, A. V.; Rose, M. Franklin (Technical Monitor)

2001-01-01

The eutectic alloys have a wide spectrum of applications due to their good castability and physical and mechanical properties. The interphase spacing resulting during solidification is an important microstructural feature that significantly influences the mechanical behavior of the material. Thus, knowledge of the evolution of the interphase spacing during solidification is necessary in order to properly design the solidification process and optimize the material properties. While the growth of regular eutectics is rather well understood, the irregular eutectics such as Al-Si or Fe-graphite exhibit undercoolings and lamellar spacings much larger than those theoretically predicted. Despite of a considerable amount of experimental and theoretical work a clear understanding of the true mechanism underlying the spacing selection in irregular eutectics is yet to be achieved. A new experimental study of the solidification of the eutectic Al-Si alloy will be reported in this paper. The measured interface undercoolings and lamellar spacing will be compared to those found in the literature in order to get more general information regarding the growth mechanism of irregular eutectics. A modification of the present theory of the eutectic growth is also proposed. The results of the modified mathematical model, accounting for a non-isothermal solid/liquid interface, will be compared to the experimental measurements.

Cross-Permeability of the Semisolid Region in Directional Solidification: A Combined Phase-Field and Lattice-Boltzmann Simulation Approach

Science.gov (United States)

Böttger, B.; Haberstroh, C.; Giesselmann, N.

2016-01-01

Based on the results of microstructure simulations, fluid flow through the semisolid region during directional solidification of the technical Ni-base alloy 718 has been studied. Three-dimensional microstructures at different positions in the semisolid region were obtained by using a multicomponent multiphase-field model that was online coupled to a commercial thermodynamic database. For the range of five different primary dendrite distances λ 1 between 50 µm and 250 µm, the flow velocity and the permeability perpendicular to the dendrite growth direction was evaluated by using a proprietary Lattice-Boltzmann model. The commercial CFD software ANSYS FLUENT was alternatively applied for reference. Consistent values of the average flow velocity along the dendrites were obtained for both methods. From the results of the fluid flow simulations, the cross-permeability was evaluated as a function of temperature and fraction liquid for each of the five different primary dendrite distances λ 1. The obtained permeability values can be approximated by a single analytical function of the fraction liquid and λ 1 and are discussed and compared with known relations from the literature.

Effect of Manganese on Microstructures and Solidification Modes of Cast Fe-Mn-Si-Cr-Ni Shape Memory Alloys

Science.gov (United States)

Peng, Huabei; Wen, Yuhua; Du, Yangyang; Yu, Qinxu; Yang, Qin

2013-10-01

We investigated microstructures and solidification modes of cast Fe-(13-27)Mn-5.5Si-8.5Cr-5Ni shape memory alloys to clarify whether Mn was an austenite former during solidification. Furthermore, we examined whether the Creq/Nieq equations (Delong, Hull, Hammer and WRC-1992 equations) and Thermo-Calc software® together with database TCFE6 were valid to predict the solidification modes of cast Fe-(13-27)Mn-5.5Si-8.5Cr-5Ni shape memory alloys. The results have shown that the solidification modes of Fe-(13-27)Mn-5.5Si-8.5Cr-5Ni alloys changed from the F mode to the FA mode with increasing the Mn concentration. Mn is an austenite former during the solidification for the cast Fe-Mn-Si-Cr-Ni shape memory alloys. The Delong, Hull, Hammer, and WRC-1992 equations as well as Thermo-Calc software® together with database TCFE6 are invalid to predict the solidification modes of cast Fe-(13-27)Mn-5.5Si-8.5Cr-5Ni SMAs. To predict the solidification modes of cast Fe-Mn-Si-Cr-Ni alloys, a new Creq/Nieq equation should be developed or the thermodynamic database of Thermo-Calc software® should be corrected.

Analytic-numerical method of determining the freezing front location

Directory of Open Access Journals (Sweden)

R. Grzymkowski

2011-07-01

Full Text Available Mathematical modeling of thermal processes combined with the reversible phase transitions of type: solid phase – liquid phase leads to formulation of the parabolic boundary problems with the moving boundary. Solution of such defined problem requires, most often, to use sophisticated numerical techniques and far advanced mathematical tools. Excellent illustration of the complexity of considered problems, as well as of the variety of approaches used for finding their solutions, gives the papers [1-4]. In the current paper, the authors present the, especially attractive from the engineer point of view, analytic-numerical method for finding the approximate solution of selected class of problems which can be reduced to the one-phase solidification problem of a plate with the unknown a priori, varying in time boundary of the region in which the solution is sought. Proposed method is based on the known formalism of initial expansion of the sought function describing the temperature field into the power series, some coefficients of which are determined with the aid of boundary conditions, and on the approximation of the function defining the location of freezing front with the broken line, parameters of which are numerically determined.

On the role of solidification modelling in Integrated Computational Materials Engineering “ICME”

International Nuclear Information System (INIS)

Schmitz, G J; Böttger, B; Apel, M

2016-01-01

Solidification during casting processes marks the starting point of the history of almost any component or product. Integrated Computational Materials Engineering (ICME) [1-4] recognizes the importance of further tracking the history of microstructure evolution along the subsequent process chain. Solidification during joining processes in general happens quite late during production, where the parts to be joined already have experienced a number of processing steps which affected their microstructure. Reliable modelling of melting and dissolution of these microstructures represents a key issue before eventually modelling ‘re’-solidification e.g. during welding or soldering. Some instructive examples of microstructure evolution during a joining process obtained on the basis of synthetic and simulated initial microstructures of an Al-Cu binary model system are discussed. (paper)

Mobile concrete solidification systems for power reactor waste

International Nuclear Information System (INIS)

Tchemitcheff, E.; Bordas, Y.

1990-01-01

In late 1988 SGN received an order from Electricite de France (EDF) for the construction of a mobile concrete solidification system to process secondary system resins generated by the P'4 and N4 series PWR power plants in France. This order was placed in view of SGN's experience with low- and medium-level radioactive waste treatment and conditioning over a period of almost 20 years. In addition to the construction of fixed waste processing facilities using more conventional technologies, SGN has been involved in application of the mobile system concept to the bituminization process in the United States, which led to the construction and commissioning of two transportable systems in collaboration with its American licensee US Ecology. It has also conducted large-scale R ampersand D on LLW/MLW concrete solidification, particularly for ion exchange resins. 5 figs

Properties of Deflagration Fronts and Models for Type IA Supernovae

Science.gov (United States)

Domínguez, I.; Höflich, P.

2000-01-01

Detailed models of the explosion of a white dwarf that include self-consistent calculations of the light curve and spectra provide a link between observational quantities and the underlying explosion model. These calculations assume spherical geometry and are based on parameterized descriptions of the burning front. Recently, the first multidimensional calculations for nuclear burning fronts have been performed. Although a fully consistent treatment of the burning fronts is beyond the current state of the art, these calculations provide a new and better understanding of the physics. Several new descriptions for flame propagation have been proposed by Khokhlov et al. and Niemeyer et al. Using various descriptions for the propagation of a nuclear deflagration front, we have studied the influence on the results of previous analyses of Type Ia supernovae, namely, the nucleosynthesis and structure of the expanding envelope. Our calculations are based on a set of delayed detonation models with parameters that give a good account of the optical and infrared light curves and of the spectral evolution. In this scenario, the burning front first propagates in a deflagration mode and subsequently turns into a detonation. The explosions and light curves are calculated using a one-dimensional Lagrangian radiation-hydro code including a detailed nuclear network. We find that the results of the explosion are rather insensitive to details of the description of the deflagration front, even if its speed and the time from the transition to detonation differ almost by a factor of 2. For a given white dwarf (WD) and a fixed transition density, the total production of elements changes by less than 10%, and the distribution in the velocity space changes by less than 7%. Qualitatively, this insensitivity of the final outcome of the explosion to the details of the flame propagation during the (slow) deflagration phase can be understood as follows: for plausible variations in the speed of

Solidification processing of high-Tc superconductors

CERN Document Server

Shiohara, Y; Nakamura, Y; Izumi, T

2001-01-01

Recent progress in the solidification processing of RE-system (RE:Y, Sm, Nd etc.) oxide superconducting materials is reviewed. The superconducting YBa/sub 2/Cu/sub 3/O/sub y/(Y123) phase is solidified from Y/sub 2/BaCuO/sub 5/(Y211) and liquid phases, by a peritectic reaction. The solidified micro and macro structure can not be explained by the peritectic reaction with diffusion in the solid but rather by diffusion in the liquid. A solidification model for this reaction is developed. It is confirmed that the prediction from the model calculation is in good agreement with the experimental results. Furthermore, the basic idea is expanded to develop a novel single crystal pulling process. Y211 powders were placed at the bottom of the crucible as the solute source for the growth and a BaO-CuO composite (Ba to Cu cation ratio was 3 to 5) was placed on the layer of Y211 powders. Temperature gradient was provided in the melt. Large bulk single crystals were obtained by this technique, and the growth mechanism was al...

Study on velocity field in a wire wrapped fuel pin bundle of sodium cooled reactor. Detailed velocity distribution in a subchannel

International Nuclear Information System (INIS)

Sato, Hiroyuki; Kobayashi, Jun; Miyakoshi, Hiroyuki; Kamide, Hideki

2009-01-01

A sodium cooled fast reactor is designed to attain a high burn-up core in a feasibility study on commercialized fast reactor cycle systems. In high burn-up fuel subassemblies, deformation of fuel pin due to the swelling and thermal bowing may decrease local flow velocity via change of flow area in the subassembly and influence the heat removal capability. Therefore, it is of importance to obtain the flow velocity distribution in a wire wrapped pin bundle. A 2.5 times enlarged 7-pin bundle water model was applied to investigate the detailed velocity distribution in an inner subchannel surrounded by 3 pins with wrapping wire. The test section consisted of a hexagonal acrylic duct tube and fluorinated resin pins which had nearly the same refractive index with that of water and a high light transmission rate. The velocity distribution in an inner subchannel with the wrapping wire was measured by PIV (Particle Image Velocimetry) through the front and lateral sides of the duct tube. In the vertical velocity distribution in a narrow space between the pins, the wrapping wire decreased the velocity downstream of the wire and asymmetric flow distribution was formed between the pin and wire. In the horizontal velocity distribution, swirl flow around the wrapping wire was obviously observed. The measured velocity data are useful for code validation of pin bundle thermalhydraulics. (author)

Evaluation of process alternatives for solidification of the West Valley high-level liquid wastes

International Nuclear Information System (INIS)

Holton, L.K.; Larson, D.E.

1982-01-01

The Department of Energy (DOE) established the West Valley Solidification Project (WVSP) in 1980. The project purpose is to demonstrate removal and solidification of the high-level liquid wastes (HLLW) presently stored in tanks at the Western New York Nuclear Service Center (WNYNSC), West Valley, New York. As part of this effort, the Pacific Northwest Laboratory (PNL) conducted a study to evaluate process alternatives for solidifcation of the WNYNSC wastes. Two process approaches for waste handling before solidification, together with solidification processes for four terminal and four interim waste forms, were considered. The first waste-handling approach, designated the salt/sludge separation process, involves separating the bulk of the nonradioactive nuclear waste constituents from the radioactive waste constituents, and the second waste-handling approach, designated the combined-waste process, involves no waste segregation prior to solidification. The processes were evaluated on the bases of their (1) readiness for plant startup by 1987, (2) relative technical merits, and (3) process cost. The study has shown that, based on these criteria, the salt/sludge separation process with a borosilicate glass waste form is preferred when producing a terminal waste form. It was also concluded that if an interim waste form is to be used, the preferred approach would be the combined waste process with a fused-salt waste form

Granular-front formation in free-surface flow of concentrated suspensions

Science.gov (United States)

Leonardi, Alessandro; Cabrera, Miguel; Wittel, Falk K.; Kaitna, Roland; Mendoza, Miller; Wu, Wei; Herrmann, Hans J.

2015-11-01

A granular front emerges whenever the free-surface flow of a concentrated suspension spontaneously alters its internal structure, exhibiting a higher concentration of particles close to its front. This is a common and yet unexplained phenomenon, which is usually believed to be the result of fluid convection in combination with particle size segregation. However, suspensions composed of uniformly sized particles also develop a granular front. Within a large rotating drum, a stationary recirculating avalanche is generated. The flowing material is a mixture of a viscoplastic fluid obtained from a kaolin-water dispersion with spherical ceramic particles denser than the fluid. The goal is to mimic the composition of many common granular-fluid materials, such as fresh concrete or debris flow. In these materials, granular and fluid phases have the natural tendency to separate due to particle settling. However, through the shearing caused by the rotation of the drum, a reorganization of the phases is induced, leading to the formation of a granular front. By tuning the particle concentration and the drum velocity, it is possible to control this phenomenon. The setting is reproduced in a numerical environment, where the fluid is solved by a lattice-Boltzmann method, and the particles are explicitly represented using the discrete element method. The simulations confirm the findings of the experiments, and provide insight into the internal mechanisms. Comparing the time scale of particle settling with the one of particle recirculation, a nondimensional number is defined, and is found to be effective in predicting the formation of a granular front.

Oxygen and carbon transfer during solidification of semiconductor grade silicon in different processes

Science.gov (United States)

Ribeyron, P. J.; Durand, F.

2000-03-01

A model is established for comparing the solute distribution resulting from four solidification processes currently applied to semiconductor grade silicon: Czochralski pulling (CZ), floating zone (FZ), 1D solidification and electromagnetic continuous pulling (EMCP). This model takes into account solid-liquid interface exchange, evaporation to or contamination by the gas phase, container dissolution, during steady-state solidification, and in the preliminary preparation of the melt. For simplicity, the transfers are treated in the crude approximation of perfectly mixed liquid and boundary layers. As a consequence, only the axial ( z) distribution can be represented. Published data on oxygen and carbon transfer give a set of acceptable values for the thickness of the boundary layers. In the FZ and EMCP processes, oxygen evaporation can change the asymptotic behaviour of the reference Pfann law. In CZ and in 1D-solidification, a large variety of solute profile curves can be obtained, because they are very sensitive to the balance between crucible dissolution and evaporation. The CZ process clearly brings supplementary degrees of freedom via the geometry of the crucible, important for the dissolution phenomena, and via the rotation rate of the crystal and of the crucible, important for acting on transfer kinetics.

Solidification method for organic solution and processing method of aqueous solution

International Nuclear Information System (INIS)

Kamoshida, Mamoru; Fukazawa, Tetsuo; Yazawa, Noriko; Hasegawa, Toshihiko

1998-01-01

The relative dielectric constant of an organic solution containing polar ingredients is controlled to 13 or less to enable its solidification. The polarity of the organic solution can be evaluated quantitatively by using the relative dielectric constant. If the relative dielectric constant is high, it can be controlled by dilution using a non-polar organic solvent of low relative dielectric constant. With such procedures, solidification can be conducted by using an economical 12-hydroxy stearic acid, process of liquid wastes can be facilitated and the safety can be ensured. (T.M.)

Improved cement solidification of low and intermediate level radioactive wastes

International Nuclear Information System (INIS)

1993-01-01

Cementation was the first and is still the most widely applied technique for the conditioning of low and intermediate level radioactive wastes. Compared with other solidification techniques, cementation is relatively simple and inexpensive. However, the quality of the final cemented waste forms depends very much on the composition of the waste and the type of cement used. Different kinds of cement are used for different kinds of waste and the compatibility of a specific waste with a specific cement type should always be carefully evaluated. Cementation technology is continuously being developed in order to improve the characteristics of cemented waste in accordance with the increasing requirements for quality of the final solidified waste. Various kinds of additives and chemicals are used to improve the cemented waste forms in order to meet all safety requirements. This report is meant mainly for engineers and designers, to provide an explanation of the chemistry of cementation systems and to facilitate the choice of solidification agents and processing equipment. It reviews recent developments in cementation technology for improving the quality of cemented waste forms and provides a brief description of the various cement solidification processes in use. Refs, figs and tabs

Effect of alloying elements on solidification of primary austenite in Ni-Mn-Cu cast iron

Directory of Open Access Journals (Sweden)

A. Janus

2011-04-01

Full Text Available Within the research, determined were direction and intensity of alloying elements influence on solidification way (directional orvolumetric of primary austenite dendrites in hypoeutectic austenitic cast iron Ni-Mn-Cu. 50 cast shafts dia. 20 mm were analysed.Chemical composition of the alloy was as follows: 1.7 to 3.3 % C, 1.4 to 3.1 % Si, 2.8 to 9.9 % Ni, 0.4 to 7.7 % Mn, 0 to 4.6 % Cu, 0.14 to0.16 % P and 0.03 to 0.04 % S. The discriminant analysis revealed that carbon influences solidification of primary austenite dendrites most intensively. It clearly increases the tendency to volumetric solidification. Influence of the other elements is much weaker. This means that the solidification way of primary austenite dendrites in hypoeutectic austenitic cast iron Ni-Mn-Cu does not differ from that in an unalloyed cast iron.

Solidification of ion exchange resin wastes in hydraulic cement

International Nuclear Information System (INIS)

Neilson, R.M. Jr.; Kalb, P.; Fuhrmann, M.; Colombo, P.

1982-01-01

Work has been conducted to investigate the solidification of ion exchange resin wastes with portland cements. These efforts have been directed toward the development of acceptable formulations for the solidification of ion exchange resin wastes and the characterization of the resultant waste forms. This paper describes formulation development work and defines acceptable formulations in terms of ternary phase compositional diagrams. The effects of cement type, resin type, resin loading, waste/cement ratio and water/cement ratio are described. The leachability of unsolidified and solidified resin waste forms and its relationship to full-scale waste form behavior is discussed. Gamma irradiation was found to improve waste form integrity, apparently as a result of increased resin crosslinking. Modifications to improve waste form integrity are described. 3 tables

SITE-94. Estimated rates of redox-front migration in granitic rocks

International Nuclear Information System (INIS)

Arthur, R.C.

1996-10-01

Analytical models for the rate of migration of oxidizing groundwaters are derived based on the stationary-state approximation to coupled fluid flow and water-rock interaction, and are constrained by molar concentrations of ferrous silicate, oxide, and sulfide minerals in the granites and associated fractures comprising the host rock beneath Aespoe. Model results indicate that small amounts of ferrous minerals in Aespoe granites and fractures will retard the downward migration of oxidizing conditions that could be generated by infiltration of glacial meltwaters during periods of glacial maxima and retreat. Calculated front velocities are retarded relative to Darcy fluxes observed in conductive fracture zones at Aespoe (0.3 to 3 m/y) by factors ranging from 10 -3 to 10 -4 . Corresponding times for the front to migrate 500 m vary from 5,100 to 4,400,000 years. Retardation efficiency depends on mineralogy and decreases in the order: fractures > altered granites > unaltered granite. The most conductive structures in these rocks are therefore the most efficient in limiting the rate of front migration. Periods of recharge during glaciation are comparable to times required for an oxidizing front to migrate to repository levels. This suggests an oxidizing front could reach repository depths during a single glacial-interglacial event. The persistence of oxidizing conditions could be relatively short lived, however, because reversal of flow conditions driven by the advance and retreat of ice sheets could cause reducing conditions to be restored. 27 refs

Interaction mechanisms between ceramic particles and atomized metallic droplets

Science.gov (United States)

Wu, Yue; Lavernia, Enrique J.

1992-10-01

SiC particles occurred during droplet solidification. A comparison of the present results to those anticipated from well-established kinetic and thermodynamic models led to some interesting findings. First, the models proposed by Boiling and Cisse[24] and Chernov et al.[58] predict relative low critical interface velocities necessary for entrapment, inconsistent with the present experimental findings. Second, although the observed correlation between the critical front velocity and droplet diameter was generally consistent with that predicted by Stefanescu et a/.’s model,[27] the dependence on the size of SiC particles was not. In view of this discrepancy, three possible mechanisms were proposed to account for the experimental findings: nucleation of α-Al on SiC particles, entrapment of SiC particles between primary dendrite arms, and entrapment of SiC particles between secondary dendrite arms.

Modeling of quench front progression and heat transfer by radiation during reflooding of a tubular test section

International Nuclear Information System (INIS)

Clement, P.; Deruaz, R.

1976-01-01

Heat transfer modeling is presented in the scope of emergency core cooling. The rewetting of a hot dry wall during reflooding is a conduction-controlled phenomenon described by a model of heat-transfer coefficient. Upstream of the quench front, a two-dimensional approach involving both axial and transverse (or radial) heat conduction is discussed in view of thick walls, high quench front velocities and nucleate boiling. Downstream of the quench-front, high wall temperatures are reached so that a thermal radiation model is required to separate the different mechanisms of heat transfer. An attempt is made to consider radiation between walls, water droplets and vapor, with scattering emission and absorption of the two phases

Variation of Quench Propagation Velocities in YBCO Cables

CERN Document Server

Härö, E.; Stenvall, A.; 10.1007/s10948-015-2976-y

2015-01-01

changes during the quench. Due to the large temperature margin between the operation and the current sharing temperatures, the normal zone does not propagate with the temperature front. This means that the temperature will rise in a considerably larger volume when compared to the quenched volume. Thus, the evolution of the temperature distribution below current sharing temperature Tcs after the quench onset affects the normal zone propagation velocity in HTS more than in LTS coils. This can be seen as an acceleration of the quench propagation velocities while the quench evolves when margin to Tcs is high. In this paper we scrutinize quench propagation in a stack of YBCO cables with an in-house finite element method software which solves the heat diffusion equation. We compute the longitudinal and transverse normal zone propagation velocities at various distances from the hot spot to demonstrate the distance-variation...

Fluid mechanics of directional solidification at reduced gravity

Science.gov (United States)

Chen, C. F.

1992-01-01

The primary objective of the proposed research is to provide additional groundbased support for the flight experiment 'Casting and Solidification Technology' (CAST). This experiment is to be performed in the International Microgravity Laboratory-1 (IML-1) scheduled to be flown on a space shuttle mission scheduled for 1992. In particular, we will provide data on the convective motion and freckle formation during directional solidification of NH4Cl from its aqueous solution at simulated parameter ranges equivalent to reducing the gravity from the sea-level value down to 0.1 g or lower. The secondary objectives of the proposed research are to examine the stability phenomena associated with the onset of freckles and the mechanisms for their subsequent growth and decline (to eventual demise of some) by state-of-the-art imaging techniques and to formulate mathematical models for the prediction of the observed phenomena.

Development of high-level waste solidification technology 1

Energy Technology Data Exchange (ETDEWEB)

Kim, Joon Hyung; Kim, Hwan Young; Kim, In Tae [and others

1999-02-01

Spent nuclear fuel contains useful nuclides as valuable resource materials for energy, heat and catalyst. High-level wastes (HLW) are expected to be generated from the R and D activities and reuse processes. It is necessary to develop vitrification or advanced solidification technologies for the safe long-term management of high level wastes. As a first step to establish HLW vitrification technology, characterization of HLWs that would arise at KAERI site, glass melting experiments with a lab-scale high frequency induction melter, and fabrication and property evaluation of base-glass made of used HEPA filter media and additives were performed. Basic study on the fabrication and characterization of candidate ceramic waste form (Synroc) was also carried out. These HLW solidification technologies would be directly useful for carrying out the R and Ds on the nuclear fuel cycle and waste management. (author). 70 refs., 29 tabs., 35 figs.

Retrofit of existing Dow solidification system at quad cities nuclear station

International Nuclear Information System (INIS)

Dekitis, L.; Jarvis, N.; Petri, R.; Testa, J.

1983-01-01

Over the past year ATCOR has been involved in the design, testing and supply of an In-container Mixing System Retrofit for Commonwealth Edison's Quad Cities Nuclear Station Solidification System. The system supplied by DOW, itself a retrofit of a urea formaldehyde system, was based upon use of 50 cubic foot containers (liners). ATCOR's retrofit increased liner capacity to 170 cubic feet and allowed in-cask solidification of highly radioactive material. This paper discusses the reasons for the decision to replace equipment within the originally furnished system and the development of the ATCOR plan to proof-test this equipment prior to delivery at the site. Results of this pre-testing, and a comparison between pre-tested conditions and the actual in-plan start-up tests are presented. Development of improved instrumentation and mechanical modifications which enhance the reliability of the ATCOR/DOW process In-container Mixing System was provided as a part of this project. Test results are presented on instruments, controls and the unique method of mechanical attachment of the Mixing Head to the solidification container

Manufacture history results of an investigation of the bitumen solidification object towards the check of an abandonment object

International Nuclear Information System (INIS)

Kogawa, Noboru; Kondo, Toshiyuki

2001-08-01

In order to make this book reflect in the investigation which turned the bitumen solidification object to maintenance of the abandonment object technical standard on condition of carrying out subterranean disposal in the future, it created for the purpose of utilizing as precious sources of information, such as a nuclide inventory in the living body, group-izing of the past campaign required for typical solidification object selection, and information offer at the time of disposal examination. A development operation history collected so that histories including the shift action in an institution of the formation of discharge reduction of the characteristic of solidification object manufacture outlines, such as composition of the process of an institution and a solidification object and a storage actual result, the contents of an examination of the past campaign, and the solidification object manufactured based on topics or radioactive iodine and radioactive carbon etc., such as the past contents of an examination/operation, may grasp comprehensively in creation, and it carried out as the composition stared the trend of future disposal fixedly. It was a period (for 16 years) until an bituminization demonstration facility processing institution will start a cold examination from April (Showa 57), 1982, and it starts a hot examination from May 4, it starts solidification processing technical development operation from October 6 and it results in the fire explosion accident on March 11 (Heisei 9), 1997, and low level radioactivity concentration waste fluid was processed 7,438m 3 and 29,967 bitumen solidification objects were manufactured. According to the accident, it is necessary to hand it down to future generations with processing technology while the bitumen solidification object manufactured in 15 years although the bituminization demonstration facility processing institution came to close the mission holds information precious when considering future disposal

Macrosegregation and Grain Formation Caused by Convection Associated with Directional Solidification Through Cross-Section Increase

Science.gov (United States)

Ghods, Masoud; Lauer, Mark; Tewari, Surendra; Poirier, David; Grugel, Richard

2016-01-01

Cylindrical Al-7 wt% Silicon, Al-19 wt% Copper and Lead-6 wt% Antimony alloy samples were directionally solidified (DS) with liquid above, solid below, and gravity pointing down, in graphite crucibles having an abrupt cross-sectional increase. These alloys have similar solidification shrinkage but are expected to have different degrees of thermosolutal convection during solidification. Microstructures in the DS samples in the vicinity of the section change have been studied in order to examine the effect of convection associated with the combined influence of thermosolutal effects and solidification shrinkage. Extensive radial and axial macrosegregation associated with cross-section change is observed. It also appears that steepling and local primary alpha-phase remelting resulting from convection are responsible for stray grain formation at the reentrant corners. Preliminary results from a numerical model, which includes solidification shrinkage and thermosolutal convection in the mushy zone, indicate that these regions are prone to solutal remelting of dendrites.

Crash characteristics and injury patterns of restrained front seat occupants in far-side impacts.

Science.gov (United States)

Yoganandan, Narayan; Arun, Mike W J; Halloway, Dale E; Pintar, Frank A; Maiman, Dennis J; Szabo, Aniko; Rudd, Rodney W

2014-01-01

The study was conducted to determine the association between vehicle-, crash-, and demographic-related factors and injuries to front seat far-side occupants in modern environments. Field data were obtained from the NASS-CDS database for the years 2009-2012. Inclusion factors included the following: adult restrained front outboard-seated occupants, no ejection or rollovers, and vehicle model years less than 10 years old at the time of crash. Far-side crashes were determined by using collision deformation classification. Injuries were scored using the Abbreviated Injury Scale (AIS). Injuries (MAIS 2+, MAIS 3+, M denotes maximum score) were examined based on demographics, change in velocity, vehicle type, direction of force, extent zone, collision partner, and presence of another occupant in the front seat. Only weighted data were used in the analysis. Injuries to the head and face, thorax, abdomen, pelvis, and upper and lower extremity regions were studied. Odds ratios and upper and lower confidence intervals were estimated from multivariate analysis. Out of 519,195 far-side occupants, 17,715 were MAIS 2+ and 4,387 were MAIS 3+ level injured occupants. The mean age, stature, total body mass, and body mass index (BMI) were 40.7 years, 1.7 m, 77.2 kg, and 26.8 kg/m2, respectively. Of occupants with MAIS 2+ injuries, 51% had head and 19% had thorax injuries. Of occupants with MAIS 3+ injuries, 50% had head and 69% had thorax injuries. The cumulative distribution of changes in velocities at the 50th percentile for the struck vehicle for all occupants and occupants with MAIS 2+ and MAIS 3+ injuries were 19, 34, and 42 km/h, respectively. Furthermore, 73% of MAIS 2+ injuries and 86% of MAIS 3+ injuries occurred at a change in velocity of 24 km/h or greater. Odds of sustaining MAIS 2+ and MAIS 3+ injuries increased with each unit increase in change in velocity, stature, and age, with one exception. Odds of sustaining injuries were higher with the presence of an occupant in

Measurements of laminar burning velocities and flame stability analysis for dissociated methanol-air-diluent mixtures at elevated temperatures and pressures

Energy Technology Data Exchange (ETDEWEB)

Zhang, Xuan; Huang, Zuohua; Zhang, Zhiyuan; Zheng, Jianjun; Yu, Wu; Jiang, Deming [State Key Laboratory of Multiphase Flow in Power Engineering, Xi' an Jiaotong University, Xi' an 710049 (China)

2009-06-15

The laminar burning velocities and Markstein lengths for the dissociated methanol-air-diluent mixtures were measured at different equivalence ratios, initial temperatures and pressures, diluents (N{sub 2} and CO{sub 2}) and dilution ratios by using the spherically outward expanding flame. The influences of these parameters on the laminar burning velocity and Markstein length were analyzed. The results show that the laminar burning velocity of dissociated methanol-air mixture increases with an increase in initial temperature and decreases with an increase in initial pressure. The peak laminar burning velocity occurs at equivalence ratio of 1.8. The Markstein length decreases with an increase in initial temperature and initial pressure. Cellular flame structures are presented at early flame propagation stage with the decrease of equivalence ratio or dilution ratio. The transition positions can be observed in the curve of flame propagation speed to stretch rate, indicating the occurrence of cellular structure at flame fronts. Mixture diluents (N{sub 2} and CO{sub 2}) will decrease the laminar burning velocities of mixtures and increase the sensitivity of flame front to flame stretch rate. Markstein length increases with an increase in dilution ratio except for very lean mixture (equivalence ratio less than 0.8). CO{sub 2} dilution has a greater impact on laminar flame speed and flame front stability compared to N{sub 2}. It is also demonstrated that the normalized unstretched laminar burning velocity is only related to dilution ratio and is not influenced by equivalence ratio. (author)

Spurious Grain Formation at Cross-Sectional Expansion During Directional Solidification: Influence of Thermosolutal Convection

Science.gov (United States)

Ghods, M.; Lauer, M.; Upadhyay, S. R.; Grugel, R. N.; Tewari, S. N.; Poirier, D. R.

2018-04-01

Formation of spurious grains during directional solidification (DS) of Al-7 wt.% Si and Al-19 wt.% Cu alloys through an abrupt increase in cross-sectional area has been examined by experiments and by numerical simulations. Stray grains were observed in the Al-19 wt.% Cu samples and almost none in the Al-7 wt.% Si. The locations of the stray grains correlate well where numerical solutions indicate the solute-rich melt to be flowing up the thermal gradient faster than the isotherm velocity. It is proposed that the spurious grain formation occurred by fragmentation of slender tertiary dendrite arms was enhanced by thermosolutal convection. In Al-7 wt.% Si, the dendrite fragments sink in the surrounding melt and get trapped in the dendritic array growing around them, and therefore they do not grow further. In the Al-19 wt.% Cu alloy, on the other hand, the dendrite fragments float in the surrounding melt and some find conducive thermal conditions for further growth and become stray grains.

Solidification of radioactive wastes with inorganic binders (literature survey)

International Nuclear Information System (INIS)

Rudolph, G.; Koester, R.

A survey is provided on solidification of radioactive waste solutions, sludges and tritium waste water through cement and other inorganic binders. A general survey of the possibilities described in the literature is followed by a somewhat more detailed description of the work carried on at four research establishments in the United States, Oak Ridge National Laboratory, Savannah River Laboratory, Brookhaven National Laboratory, and Atlantic Richfield Hanford Company, supplemented by personal information. Additional sections describe the experiences with various types of cement and the possibilities for improvement of solidification products through preliminary fixation of the toxic nuclides (transformation into insoluble products or absorption); there is a further possibility of post-treatment through polymer impregnation. Finally, definition and determination of leachability are provided and some results compiled. 74 references, 7 figures, 5 tables

Elimination of Hot Tears in Steel Castings by Means of Solidification Pattern Optimization

Science.gov (United States)

Kotas, Petr; Tutum, Cem Celal; Thorborg, Jesper; Hattel, Jesper Henri

2012-06-01

A methodology of how to exploit the Niyama criterion for the elimination of various defects such as centerline porosity, macrosegregation, and hot tearing in steel castings is presented. The tendency of forming centerline porosity is governed by the temperature distribution close to the end of the solidification interval, specifically by thermal gradients and cooling rates. The physics behind macrosegregation and hot tears indicate that these two defects also are dependent heavily on thermal gradients and pressure drop in the mushy zone. The objective of this work is to show that by optimizing the solidification pattern, i.e., establishing directional and progressive solidification with the help of the Niyama criterion, macrosegregation and hot tearing issues can be both minimized or eliminated entirely. An original casting layout was simulated using a transient three-dimensional (3-D) thermal fluid model incorporated in a commercial simulation software package to determine potential flaws and inadequacies. Based on the initial casting process assessment, multiobjective optimization of the solidification pattern of the considered steel part followed. That is, the multiobjective optimization problem of choosing the proper riser and chill designs has been investigated using genetic algorithms while simultaneously considering their impact on centerline porosity, the macrosegregation pattern, and primarily on hot tear formation.

The solidification of aluminum production waste in geopolymer matrix

Czech Academy of Sciences Publication Activity Database

Perná, Ivana; Hanzlíček, Tomáš

2014-01-01

Roč. 84, DEC 1 (2014), s. 657-662 ISSN 0959-6526 Institutional support: RVO:67985891 Keywords : aluminum waste * solidification * recycling * geopolymer Subject RIV: DM - Solid Waste and Recycling Impact factor: 3.844, year: 2014

Remotely operated facility for in situ solidification of fissile uranium

International Nuclear Information System (INIS)

McGinnis, C.P.; Collins, E.D.; Patton, B.D.

1986-01-01

A heavily shielded, remotely operated facility, located within the Radiochemical processing Plant at Oak Ridge National Laboratory (ORNL), has been designed and is being operated to convert approx.1000 kg of fissile uranium (containing approx.75% 235 U, approx.10% 233 U, and approx.140 ppM 232 U) from a nitrate solution (130 g of uranium per L) to a solid oxide form. This project, the Consolidated Edison Uranium Solidification Program (CEUSP), is being carried out in order to prepare a stable uranium form for longterm storage. This paper describes the solidification process selected, the equipment and facilities required, the experimental work performed to ensure successful operation, some problems that were solved, and the initial operations

Study of plastic solidification process on solid radioactive waste treatment

International Nuclear Information System (INIS)

Jing Weiguan; Zhang Yinsheng; Qian Wenju

1994-01-01

Comparisons between the plastic solidification conditions of incinerated ash and waste cation resin by using thermosetting plastic polyvinyl chloride (PVC), polystyrene (PS) and polyethylene (PE), and identified physico-chemical properties and irradiation resistance of solidified products were presented. These solidified products have passed through different tests as compression strength, leachability, durability, stability, permeability and irradiation resistance (10 6 Gy) etc. The result showed that the solidified products possessed stable properties and met the storage requirement. The waste tube of radioimmunoassay, being used as solidification medium to contain incinerated ash, had good mechanical properties and satisfactory volume reduction. This process may develop a new way for disposal solid radioactive waste by means of re-using waste

Elimination of Hot Tears in Steel Castings by Means of Solidification Pattern Optimization

DEFF Research Database (Denmark)

Kotas, Petr; Tutum, Cem Celal; Thorborg, Jesper

2012-01-01

A methodology of how to exploit the Niyama criterion for the elimination of various defects such as centerline porosity, macrosegregation, and hot tearing in steel castings is presented. The tendency of forming centerline porosity is governed by the temperature distribution close to the end...... of the solidification interval, specifically by thermal gradients and cooling rates. The physics behind macrosegregation and hot tears indicate that these two defects also are dependent heavily on thermal gradients and pressure drop in the mushy zone. The objective of this work is to show that by optimizing...... the solidification pattern, i.e., establishing directional and progressive solidification with the help of the Niyama criterion, macrosegregation and hot tearing issues can be both minimized or eliminated entirely. An original casting layout was simulated using a transient three-dimensional (3-D) thermal fluid model...

Numerical investigation on natural convection and solidification of molten pool with OpenFOAM

International Nuclear Information System (INIS)

Wang Xi; Meng Zhaocan; Cheng Xu

2015-01-01

The in-vessel retention is adopted by the third generation nuclear power technology as an important severe accident mitigation strategy. The integrity of reactor pressure vessel depends on the heat flux distribution of molten pool. In present study, the solidification model in open source CFD software OpenFOAM was applied to simulate solidification and natural convection which was driven by internal heat source or temperature difference. The stratified molten pool heat transfer experiment carried out by Royal Institute of Technology was analyzed in the paper, and the solidified crust, temperature and heat flux distributions were obtained. The simulation results were compared with experimental data. It is shown that this numerical method can be used in the simulation of natural convection and solidification of molten pool, and it will probably be used in the analysis of molten corium behavior in reactor lower head. (authors)

External field effects on diffusion and solidification derived from the free-volume model

Science.gov (United States)

Miller, R. I.; Ruff, R. C.

1975-01-01

Expressions for the diffusion coefficient and the solidification rate from the free-volume model of liquids developed by Turnbull and Cohen have been used to estimate the effects which microgravity and magnetic fields will have on these quantities. The mathematical formalism describing changes of the diffusion coefficient and the solidification rate is the same for both the microgravity and magnetic field cases, but the difference between the magnitudes of the two effects is quite large. The change in the two parameters is found to be less than .0001% for the microgravity case and on the order of 0.1 to 1.1% for the magnetic field case for four representative materials. The diffusion coefficient and the solidification rate are found to increase under the influence of an applied magnetic field, and this is in agreement with experimental observations.

Simulated front crawl swimming performance related to critical speed and critical power.

Science.gov (United States)

Toussaint, H M; Wakayoshi, K; Hollander, A P; Ogita, F

1998-01-01

Competitive pool swimming events range in distance from 50 to 1500 m. Given the difference in performance times (+/- 23-1000 s), the contribution of the aerobic and anaerobic energy systems changes considerably with race distance. In training practice the regression line between swimming distance and time (Distance = critical velocity x time + anaerobic swimming capacity) is used to determine the individual capacity of the aerobic and anaerobic metabolic pathways. Although there is confidence that critical velocity and anaerobic swimming capacity are fitness measures that separate aerobic and anaerobic components, a firm theoretical basis for the interpretation of these results does not exist. The purpose of this study was to evaluate the critical power concept and anaerobic swimming capacity as measures of the aerobic and anaerobic capacity using a modeling approach. A systems model was developed that relates the mechanics and energetics involved in front crawl swimming performance. From actual swimming flume measurements, the time dependent aerobic and anaerobic energy release was modeled. Data derived from the literature were used to relate the energy cost of front crawl swimming to swimming velocity. A balance should exist between the energy cost to swim a distance in a certain time and the concomitant aerobic and anaerobic energy release. The ensuing model was used to predict performance times over a range of distances (50-1500 m) and to calculate the regression line between swimming distance and time. Using a sensitivity analysis, it was demonstrated that the critical velocity is indicative for the capacity of the aerobic energy system. Estimates of the anaerobic swimming capacity, however, were influenced by variations in both anaerobic and aerobic energy release. Therefore, it was concluded that the anaerobic swimming capacity does not provide a reliable estimate of the anaerobic capacity.

Realization of a neural algorithm by means of front-propagation in a thyristor-based hybrid system

CERN Document Server

Niedernostheide, F J; Freyd, O; Bode, M; Gorbatyuk, A V

2003-01-01

Propagating fronts are generic structures in a bistable diffusion-driven system and can be used to realize neural algorithms, as e.g., the Kohonen or the neural-gas algorithm. We present an analog-digital hybrid system based on a thyristor-like structure with several gate terminals. This structure represents the continuous part in which a propagating front, separating a region of high current density from a region of low current density, is used to control the learning process of the neural algorithm. With a system containing five neurons and five gates in a quasi one-dimensional arrangement it is demonstrated that an efficient parallel operating learning process can be realized by using the winner-take-all principle and the front propagation, i.e. exploiting the intrinsic dynamics of the semiconductor device. Finally, numerical and analytical investigations of the dependency of the front velocity and its width on the load current have been performed since these are essential parameters for improving the netw...

Realization of a neural algorithm by means of front-propagation in a thyristor-based hybrid system

International Nuclear Information System (INIS)

Niedernostheide, F.-J.; Schulze, H.-J.; Freyd, O.; Bode, M.; Gorbatyuk, A.V.

2003-01-01

Propagating fronts are generic structures in a bistable diffusion-driven system and can be used to realize neural algorithms, as e.g., the Kohonen or the neural-gas algorithm. We present an analog-digital hybrid system based on a thyristor-like structure with several gate terminals. This structure represents the continuous part in which a propagating front, separating a region of high current density from a region of low current density, is used to control the learning process of the neural algorithm. With a system containing five neurons and five gates in a quasi one-dimensional arrangement it is demonstrated that an efficient parallel operating learning process can be realized by using the winner-take-all principle and the front propagation, i.e. exploiting the intrinsic dynamics of the semiconductor device. Finally, numerical and analytical investigations of the dependency of the front velocity and its width on the load current have been performed since these are essential parameters for improving the network performance

Investigation of solidification behavior of the Sn-rich ternary Sn–Bi–Zn alloys

Directory of Open Access Journals (Sweden)

S Mladenović

2017-03-01

Full Text Available Solidification properties and microstructure of six as-cast Sn–Bi–Zn alloys with 80 at.% of Sn and variable contents of Bi and Zn were experimentally investigated using the scanning electron microscopy (SEM with energy-dispersive X-ray spectroscopy (EDS and differential scanning calorimetry (DSC. The experimentally obtained results were compared with predicted phase equilibria according to the calculation of phase diagram (CALPHAD method and by the Scheil solidification simulation.

Analysis of capital and operating costs associated with high level waste solidification processes

International Nuclear Information System (INIS)

Heckman, R.A.; Kniazewycz, B.G.

1978-03-01

An analysis was performed to evaluate the sensitivity of annual operating costs and capital costs of waste solidification processes to various parameters defined by the requirements of a proposed Federal waste repository. Five process methods and waste forms examined were: salt cake, spray calcine, fluidized bed calcine, borosilicate glass, and supercalcine multibarrier. Differential cost estimates of the annual operating and maintenance costs and the capital costs for the five HLW solidification alternates were developed

Solidification Mechanism of the D-Gun Sprayed Fe-Al Particles

Directory of Open Access Journals (Sweden)

Wołczyński W.

2017-12-01

Full Text Available The detonation gas spraying method is used to study solidification of the Fe-40Al particles after the D-gun spraying and settled on the water surface. The solidification is divided into two stages. First, the particle solid shell forms during the particle contact with the surrounding air / gas. Usually, the remaining liquid particle core is dispersed into many droplets of different diameter. A single Fe-Al particle is described as a body subjected to a rotation and finally to a centrifugal force leading to segregation of iron and aluminum. The mentioned liquid droplets are treated as some spheres rotated freely / chaotically inside the solid shell of the particle and also are subjected to the centrifugal force. The centrifugal force, and first of all, the impact of the particles onto the water surface promote a tendency for making punctures in the particles shell. The droplets try to desert / abandon the mother-particles through these punctures. Some experimental evidences for this phenomenon are delivered. It is concluded that the intensity of the mentioned phenomenon depends on a given droplet momentum. The droplets solidify rapidly during their settlement onto the water surface at the second stage of the process under consideration. A model for the solidification mechanism is delivered.

Stabilization/solidification of synthetic Nigerian drill cuttings | Opete ...

African Journals Online (AJOL)

Stabilization/solidification of synthetic Nigerian drill cuttings. SEO Opete, IA Mangibo, ET Iyagba. Abstract. In the Nigerian oil and gas industry, large quantities of oily and synthetic drill cuttings are produced annually. These drill cuttings are heterogeneous wastes which comprises of hydrocarbons, heavy metals and ...

A Comparative study of solidification of Al-Cu alloy under flow of cylindrical radial heat and the unidirectional vertically

Directory of Open Access Journals (Sweden)

Jean Robert P. Rodrigues

2014-09-01

Full Text Available In spite of technological importance of solidification of metallic alloys under radial heat flow, relatively few studies have been carried out in this area. In this work the solidification of Al 4.5 wt% Cu cylinders against a steel massive mold is analyzed and compared with unidirectional solidification against a cooled mold. Initially temperature variations at different positions in the casting and in the mold were measured during solidification using a data acquisition system. These temperature variations were introduced in a numerical method in order to determine the variation of heat transfer coefficient at metal/mold interface by inverse method. The primary and secondary dendrite arm spacing variations were measured through optical microscopy. Comparisons carried out between experimental and numerical data showed that the numerical method describes well the solidification processes under radial heat flux.

Techniques for the solidification of high-level wastes

International Nuclear Information System (INIS)

1977-01-01

The problem of the long-term management of the high-level wastes from the reprocessing of irradiated nuclear fuel is receiving world-wide attention. While the majority of the waste solutions from the reprocessing of commercial fuels are currently being stored in stainless-steel tanks, increasing effort is being devoted to developing technology for the conversion of these wastes into solids. A number of full-scale solidification facilities are expected to come into operation in the next decade. The object of this report is to survey and compare all the work currently in progress on the techniques available for the solidification of high-level wastes. It will examine the high-level liquid wastes arising from the various processes currently under development or in operation, the advantages and disadvantages of each process for different types and quantities of waste solutions, the stages of development, the scale-up potential and flexibility of the processes

Thermodynamic assessment of liquid composition change during solidification and its effect on freckle formation in superalloys

International Nuclear Information System (INIS)

Long Zhengdong; Liu Xingbo; Yang Wanhong; Chang, K.-M.; Barbero, Ever

2004-01-01

The solidification macrosegregation, i.e. freckle, becomes more and more concerned with ever increasing demand for the large ingot size of superalloys. The evaluation of freckle formation is very difficult because of the less understanding of freckle formation mechanism and complex solidification behaviors of multi-component superalloys. The macrostructure of typical Nb-bearing and Ti-bearing superalloys in horizontally directional solidification and vacuum arc remelting (VAR) ingots were investigated to clarify the freckle formation mechanism. The thermodynamic approach was proposed to simulate the solidification behaviors. The relative Ra numbers, a reliable criterion, of freckle formation for some alloys were obtained based on the results of thermodynamic calculations. This thermodynamic approach was evaluated through comparison of the calculations from semi-experimental results. The Ra numbers obtained by thermodynamic approach are in good agreement with the ingot size capability of the industry melting shops, which is limited mainly by freckle defects

Microstructure and fractal characteristics of the solid-liquid interface forming during directional solidification of Inconel 718

Directory of Open Access Journals (Sweden)

WANG Ling

2007-08-01

Full Text Available The solidification microstructure and fractal characteristics of the solid-liquid interfaces of Inconel 718, under different cooling rates during directional solidification, were investigated by using SEM. Results showed that 5 μm/s was the cellular-dendrite transient rate. The prime dendrite arm spacing (PDAS was measured by Image Tool and it decreased with the cooling rate increased. The fractal dimension of the interfaces was calculated and it changes from 1.204310 to 1.517265 with the withdrawal rate ranging from 10 to 100 μm/s. The physical significance of the fractal dimension was analyzed by using fractal theory. It was found that the fractal dimension of the dendrites can be used to describe the solidification microstructure and parameters at low cooling rate, but both the fractal dimension and the dendrite arm spacing are needed in order to integrally describe the evaluation of the solidification microstructure completely.

Automated Detection of Fronts using a Deep Learning Convolutional Neural Network

Science.gov (United States)

Biard, J. C.; Kunkel, K.; Racah, E.

2017-12-01

A deeper understanding of climate model simulations and the future effects of global warming on extreme weather can be attained through direct analyses of the phenomena that produce weather. Such analyses require these phenomena to be identified in automatic, unbiased, and comprehensive ways. Atmospheric fronts are centrally important weather phenomena because of the variety of significant weather events, such as thunderstorms, directly associated with them. In current operational meteorology, fronts are identified and drawn visually based on the approximate spatial coincidence of a number of quasi-linear localized features - a trough (relative minimum) in air pressure in combination with gradients in air temperature and/or humidity and a shift in wind, and are categorized as cold, warm, stationary, or occluded, with each type exhibiting somewhat different characteristics. Fronts are extended in space with one dimension much larger than the other (often represented by complex curved lines), which poses a significant challenge for automated approaches. We addressed this challenge by using a Deep Learning Convolutional Neural Network (CNN) to automatically identify and classify fronts. The CNN was trained using a "truth" dataset of front locations identified by National Weather Service meteorologists as part of operational 3-hourly surface analyses. The input to the CNN is a set of 5 gridded fields of surface atmospheric variables, including 2m temperature, 2m specific humidity, surface pressure, and the two components of the 10m horizontal wind velocity vector at 3-hr resolution. The output is a set of feature maps containing the per - grid cell probabilities for the presence of the 4 front types. The CNN was trained on a subset of the data and then used to produce front probabilities for each 3-hr time snapshot over a 14-year period covering the continental United States and some adjacent areas. The total frequencies of fronts derived from the CNN outputs matches

Cadarache LOR (liquides organiques radioactifs) treatment by a solidification process using NOCHAR polymers

International Nuclear Information System (INIS)

Vaudey, Claire-Emilie; Renou, Sebastien; Kelley, Dennis; Cochaud, Chantal; Serrano, Roger

2013-01-01

In France, two options can be considered to handle the Very Low Level Waste (VLLW) and the Low Level Waste (LLW). The first one is the incineration at CENTRACO facility and the second one is the disposal at ANDRA sites. The waste acceptance in these two channels is dependent upon the adequacy between the waste characteristics (physical chemistry and radiological) and the channel specifications. If the waste characteristics and the channel specifications (presence of significant quantities of halogens, complexing agents, organic components... or/and high activity limits) are incompatible, an alternative solution have to be identify. It consists of a waste pre-treatment process. For Cadarache LOR (Liquides Organiques Radioactifs) waste streams, two radioactive scintillation cocktails have to be treated. They are composed of a mix of organic liquids and water: for the first one, 19 % of organic compounds (xylene, mesitylene, diphenyloxazole, TBP...) and 86.9 % of water, and for the second one, 23 % of organic compounds (TBP...) and 77 % of water. They contain halogens (chlorine and fluorine), complexants agents (nitrate, sulphate, oxalate and formate) and have got αβγ spectra with mass activities equal to some 100 Bq/g. Therefore, tritium is also present. As a consequence, in order for storage acceptance at the ANDRA site, it is necessary to pre-treat the waste. An adequate solution seems to be a solidification process using NOCHAR polymers. Indeed, NOCHAR polymers correspond to an important variety of products applied to the treatment of radioactive aqueous and organic liquids (solvent, oil, solvent/oil mixing ...) and sludge through a mechanical and chemical solidification process. For Cadarache LOR, N910 and N960 respectively dedicated to the organic and aqueous liquids solidification are considered. With the N910, the organic waste solidification occurs in two steps. As the organic liquid travels moves through the polymer strands, the strands swell and

Influences on Distribution of Solute Atoms in Cu-8Fe Alloy Solidification Process Under Rotating Magnetic Field

Science.gov (United States)

Zou, Jin; Zhai, Qi-Jie; Liu, Fang-Yu; Liu, Ke-Ming; Lu, De-Ping

2018-05-01

A rotating magnetic field (RMF) was applied in the solidification process of Cu-8Fe alloy. Focus on the mechanism of RMF on the solid solution Fe(Cu) atoms in Cu-8Fe alloy, the influences of RMF on solidification structure, solute distribution, and material properties were discussed. Results show that the solidification behavior of Cu-Fe alloy have influenced through the change of temperature and solute fields in the presence of an applied RMF. The Fe dendrites were refined and transformed to rosettes or spherical grains under forced convection. The solute distribution in Cu-rich phase and Fe-rich phase were changed because of the variation of the supercooling degree and the solidification rate. Further, the variation in solute distribution was impacted the strengthening mechanism and conductive mechanism of the material.

Numerical Simulation on the Origin of Solidification Cracking in Laser Welded Thick-Walled Structures

Directory of Open Access Journals (Sweden)

Nasim Bakir

2018-06-01

Full Text Available One of the main factors affecting the use of lasers in the industry for welding thick structures is the process accompanying solidification cracks. These cracks mostly occurring along the welding direction in the welding center, and strongly affect the safety of the welded components. In the present study, to obtain a better understanding of the relation between the weld pool geometry, the stress distribution and the solidification cracking, a three-dimensional computational fluid dynamic (CFD model was combined with a thermo-mechanical model. The CFD model was employed to analyze the flow of the molten metal in the weld pool during the laser beam welding process. The weld pool geometry estimated from the CFD model was used as a heat source in the thermal model to calculate the temperature field and the stress development and distributions. The CFD results showed a bulging region in the middle depth of the weld and two narrowing areas separating the bulging region from the top and bottom surface. The thermo-mechanical simulations showed a concentration of tension stresses, transversally and vertically, directly after the solidification during cooling in the region of the solidification cracking.

Picosecond phase-velocity dispersion of hypersonic phonons imaged with ultrafast electron microscopy

International Nuclear Information System (INIS)

Cremons, Daniel R.; Du, Daniel X.; Flannigan, David J.

2017-01-01

We describe the direct imaging—with four-dimensional ultrafast electron microscopy—of the emergence, evolution, dispersion, and decay of photoexcited, hypersonic coherent acoustic phonons in nanoscale germanium wedges. Coherent strain waves generated via ultrafast in situ photoexcitation were imaged propagating with initial phase velocities of up to 35 km/s across discrete micrometer-scale crystal regions. We then observe that, while each wave front travels at a constant velocity, the entire wave train evolves with a time-varying phase-velocity dispersion, displaying a single-exponential decay to the longitudinal speed of sound (5 km/s) and with a mean lifetime of 280 ps. We also find that the wave trains propagate along a single in-plane direction oriented parallel to striations introduced during specimen preparation, independent of crystallographic direction. Elastic-plate modeling indicates the dynamics arise from excitation of a single, symmetric (dilatational) guided acoustic mode. Further, by precisely determining the experiment time-zero position with a plasma-lensing method, we find that wave-front emergence occurs approximately 100 ps after femtosecond photoexcitation, which matches well with Auger recombination times in germanium. We conclude by discussing the similarities between the imaged hypersonic strain-wave dynamics and electron/hole plasma-wave dynamics in strongly photoexcited semiconductors.

Picosecond phase-velocity dispersion of hypersonic phonons imaged with ultrafast electron microscopy

Science.gov (United States)

Cremons, Daniel R.; Du, Daniel X.; Flannigan, David J.

2017-12-01

Here, we describe the direct imaging—with four-dimensional ultrafast electron microscopy—of the emergence, evolution, dispersion, and decay of photoexcited, hypersonic coherent acoustic phonons in nanoscale germanium wedges. Coherent strain waves generated via ultrafast in situ photoexcitation were imaged propagating with initial phase velocities of up to 35 km/s across discrete micrometer-scale crystal regions. We observe that, while each wave front travels at a constant velocity, the entire wave train evolves with a time-varying phase-velocity dispersion, displaying a single-exponential decay to the longitudinal speed of sound (5 km/s) and with a mean lifetime of 280 ps. We also find that the wave trains propagate along a single in-plane direction oriented parallel to striations introduced during specimen preparation, independent of crystallographic direction. Elastic-plate modeling indicates the dynamics arise from excitation of a single, symmetric (dilatational) guided acoustic mode. Further, by precisely determining the experiment time-zero position with a plasma-lensing method, we find that wave-front emergence occurs approximately 100 ps after femtosecond photoexcitation, which matches well with Auger recombination times in germanium. We conclude by discussing the similarities between the imaged hypersonic strain-wave dynamics and electron/hole plasma-wave dynamics in strongly photoexcited semiconductors.

The efficiency of ceramic-faced metal targets at high-velocity impact

Science.gov (United States)

Tolkachev, V. F.; Konyaev, A. A.; Pakhnutova, N. V.

2017-11-01

The paper represents experimental results and engineering evaluation concerning the efficiency of composite materials to be used as an additional protection during the high- velocity interaction of a tungsten rod with a target in the velocity range of 1...5 km/s. The main parameter that characterizes the high-velocity interaction of a projectile with a layered target is the penetration depth. Experimental data, numerical simulation and engineering evaluation by modified models are used to determine the penetration depth. Boron carbide, aluminum oxide, and aluminum nickelide are applied as a front surface of targets. Based on experimental data and numerical simulation, the main characteristics of ceramics are determined, which allows composite materials to be effectively used as additional elements of protection.

On the hot cracking susceptibility of a semisolid aluminium 6061 weld: Application of a coupled solidification- thermomechanical model

International Nuclear Information System (INIS)

Rajani, H R Zareie; Phillion, A B

2015-01-01

A coupled solidification-thermomechanical model is presented that investigates the hot tearing susceptibility of an aluminium 6061 semisolid weld. Two key phenomena are considered: excessive deformation of the semisolid weld, initiating a hot tear, and the ability of the semisolid weld to heal the hot tear by circulation of the molten metal. The model consists of two major modules: weld solidification and thermomechanical analysis. 1) By means of a multi-scale model of solidification, the microstructural evolution of the semisolid weld is simulated in 3D. The semisolid structure, which varies as a function of welding parameters, is composed of solidifying grains and a network of micro liquid channels. The weld solidification module is utilized to obtain the solidification shrinkage. The size of the micro liquid channels is used as an indicator to assess the healing ability of the semisolid weld. 2) Using the finite element method, the mechanical interaction between the weld pool and the base metal is simulated to capture the transient force field deforming the semisolid weld. Thermomechanical stresses and shrinkage stresses are both considered in the analysis; the solidification contractions are extracted from the weld solidification module and applied to the deformation simulation as boundary conditions. Such an analysis enables characterization of the potential for excessive deformation of the weld. The outputs of the model are used to study the effect of welding parameters including welding current and speed, and also welding constraint on the hot cracking susceptibility of an aluminium alloy 6061 semisolid weld. (paper)

Glass-solidification method for high level radioactive liquid waste

International Nuclear Information System (INIS)

Kawamura, Kazuhiro; Kometani, Masayuki; Sasage, Ken-ichi.

1996-01-01

High level liquid wastes are removed with precipitates mainly comprising Mo and Zr, thereafter, the high level liquid wastes are mixed with a glass raw material comprising a composition having a B 2 O 3 /SiO 2 ratio of not less than 0.41, a ZnO/Li 2 O ratio of not less than 1.00, and an Al 2 O 3 /Li 2 O ratio of not less than 2.58, and they are melted and solidified into glass-solidification products. The liquid waste content in the glass-solidification products can be increased up to about 45% by using the glass raw material having such a predetermined composition. In addition, deposition of a yellow phase does not occur, and a leaching rate identical with that in a conventional case can be maintained. (T.M.)

Solidification of the polyester coatings with accelerated electron beam in air

International Nuclear Information System (INIS)

Braginskaya, A.E.; Duvakina, N.I.; Kontorov, D.S.; Kuznetsova, L.I.; Kuz'min, A.A.; Nikolaev, A.F.

1976-01-01

A study has been made to find lacquer-paint compositions which are able to solidify in the air under the action of the electron beam with formation of beautiful, glistening and firm coating on wood. As objects under study compositions on the basis of oligoethercrylates, vinyl-series monomers, non-saturated polyether resins of industrial makes and newly created polymer compositions have been used. Styrol, methylmethacrylate, dimethylacryl triglicol ether (TGM-3), α,w-dimethacrylbis (diglicol) phthalate (MDF) have been used as monomers. Solidification of lacquer-paint coatings by the electron beam has been made under the electron energy of 250-400 keV and the current density of 10-120 μA/cm 2 . Solidification of lacquers has been performed at the room temperature. The effect of reactive additives, of the nature of the monomer and the polyether on the radiational solidification process have been studied. As a result of these studies polyether compositions have been developed, which are able to solidify in the air under the action of electrons at the room temperature for a short time with formation of the glistening firm surface; these compositions can be used to obtain coatings on wood, paper, metal and other substrates

Two-dimensional time-resolved X-ray diffraction study of directional solidification in steels

International Nuclear Information System (INIS)

Yonemura, Mitsuharu

2009-01-01

Full text: The high intensity heat source used for fusion welding creates steep thermal gradients of 100 degree C/s from 1800 degree Celsius. Further, the influence of a preferred orientation is serious for observation of a directional solidification that follows the dendrite growth along the direction toward the moving heat source. Therefore, we observed the rapid solidification of weld metal at a time resolution of 0.01∼0.1seconds by the Two-Dimensional Time-Resolved X-ray Diffraction (2DTRXRD) system for real welding. The diffraction ring was dynamically observed by 2DTRXRD during arc-passing over the irradiation area of X-ray with synchrotron energy of 18 KeV. The arc power output was 10 V - 150 A, and a scan speed of the arc was 1.0 mm/s. The temperature rise of instruments was suppressed by the water-cooled copper plate under the sample. Further, the temperature distribution of the weld metal was measured by the thermocouple and related to the diffraction patterns. Consequently, solidification and solid phase transformation of low carbon steels and stainless steels were observed during rapid cooling by 2DTRXRD. In the low-carbon steel, the microstructure is formed in the 2 step process; (i) formation of crystallites and (ii) increase of crystallinity. In the stainless steel, the irregular interface layer of σ/y in the quenched metal after solidification is expected that it is easy for dendrites to move at the lower temperature. In the carbide precipitation stainless steel, it is easy for NbC to grow on σ phase with a little under cooling. Further, a mist-like pattern, which differs from the halo-pattern, in the fusion zone gave some indication of the possibilities to observe the nucleation and the early solidification by 2DTRXRD. (author)

Modeling of solidification of MMC composites during gravity casting process

Directory of Open Access Journals (Sweden)

R. Zagórski

2013-04-01

Full Text Available The paper deals with computer simulation of gravity casting of the metal matrix composites reinforced with ceramics (MMC into sand mold. The subject of our interest is aluminum matrix composite (AlMMC reinforced with ceramic particles i.e. silicon carbide SiC and glass carbon Cg. The created model describes the process taking into account solidification and its influence on the distribution of reinforcement particles. The computer calculation has been carried out in 2D system with the use of Navier-Stokes equations using ANSYS FLUENT 13. The Volume of Fluid approach (VOF and enthalpy method have been used to model the air-fluid free surface (and also volume fraction of particular continuous phases and the solidification of the cast, respectively.

Centrifugal casting of ZA8 zinc alloy and composite A356/silicon carbide: Study and modeling of phases' and particles' segregation

Science.gov (United States)

Balout, Bahaa

Centrifugation is a casting technology that allows the production of cylindrical and graduated parts with different mechanical properties through the section. The need for materials with good quality and specific mechanical properties has been driven this technology in order to produce different types of materials such as zinc alloys and graduated metal matrix composites reinforced by hard and wear resistant particles. The goal of this research project is to study and model the eutectic macrosegregation, the solidification speed, and the speeds of solidification fronts during centrifugal casting of ZA8 zinc-aluminum alloy in order to improve the part quality and increase its strength and field reliability. Moreover, the segregation of the particles during centrifugal casting of an aluminum matrix composite reinforced by silicon carbide particles (A356/SiC) is also studied to improve and control the graduation of the parts. The cooling rate, the speed, acceleration/deceleration, displacement, and segregation of the particles across the section will be modeled by discretization of Stokes' law in time in order to take into consideration the change in the centrifugal radius and melt viscosity during cooling process. This study will allow the control of the graduation degree of particles across the section in order to improve the properties and wear resistance of the composite. This composite can be used in systems where friction is critical and load is high (reinforcements of parts for the cylinders of pneumatic systems). The results show that the maximum macrosegregation zone of the eutectic across the casting section corresponds to the last point of solidification. The eutectic macrosegregation produced during centrifugal casting of thin walled part is a normal segregation which varies depending on the solidification speed and the ratio between the speeds of solidification fronts. On the other hand, it was found that the position and volume fraction of the particles

Modelling larval transport in a axial convergence front

Science.gov (United States)

Robins, P.

2010-12-01

Marine larvae exhibit different vertical swimming behaviours, synchronised by factors such as tidal currents and daylight, in order to aid retention near the parent populations and hence promote production, avoid predation, or to stimulate digestion. This paper explores two types of larval migration in an estuarine axial convergent front which is an important circulatory mechanism in many coastal regions where larvae are concentrated. A parallelised, three-dimensional, ocean model was applied to an idealised estuarine channel which was parameterised from observations of an axial convergent front which occurs in the Conwy Estuary, U.K. (Nunes and Simpson, 1985). The model successfully simulates the bilateral cross-sectional recirculation of an axial convergent front, which has been attributed to lateral density gradients established by the interaction of the lateral shear of the longitudinal currents with the axial salinity gradients. On the flood tide, there is surface axial convergence whereas on the ebb tide, there is (weaker) surface divergence. Further simulations with increased/decreased tidal velocities and with stronger/weaker axial salinity gradients are planned so that the effects of a changing climate on the secondary flow can be understood. Three-dimensional Lagrangian Particle Tracking Models (PTMs) have been developed which use the simulated velocity fields to track larvae in the estuarine channel. The PTMs take into account the vertical migrations of two shellfish species that are commonly found in the Conwy Estuary: (i) tidal migration of the common shore crab (Carcinus maenas) and (ii), diel (daily) migration of the Great scallop (Pecten maximus). These migration behaviours are perhaps the most widespread amongst shellfish larvae and have been compared with passive (drifting) particles in order to assess their relative importance in terms of larval transport. Preliminary results suggest that the net along-estuary dispersal over a typical larval

Solidification microstructures in a short fiber reinforced alloy composite containing different fiber fractions

Directory of Open Access Journals (Sweden)

JING Qing-xiu

2006-02-01

Full Text Available The solidification microstructures and micro-segregation of a fiber reinforced Al-9 Cu alloy, containing different volume fractions of Al2O3 short fibers about 6 μm diameter and made by squeeze casting have been studied. The results indicate that as volume fraction of fiber Vf increases, the size of final grains becomes finer in the matrix. If λf /λ＞1, the fibers have almost no influence on the solidification behavior of the matrix, so the final grains grow coarse, where λf is the average inter-fiber spacing and λ is the secondary dendrite arm spacing. While if λf /λ＜1, the growth of crystals in the matrix is affected significantly by the fibers and the grain size is reduced to the value of the inter-fiber spacing. The fibers influence the average length of a solidification volume element L of the matrix and also influence the solidification time θt of the matrix. As a result of fibers influencing L and θt, the micro-segregation in the matrix is improved when the composite contains more fibers, although the level of the improvement is slight. The Clyne-Kurz model can be used to semi-quantitatively analyze the relationship between Vf and the volume fraction fe of the micro-segregation eutectic structure.

A Three-Stage Mechanistic Model for Solidification Cracking During Welding of Steel

Science.gov (United States)

Aucott, L.; Huang, D.; Dong, H. B.; Wen, S. W.; Marsden, J.; Rack, A.; Cocks, A. C. F.

2018-03-01

A three-stage mechanistic model for solidification cracking during TIG welding of steel is proposed from in situ synchrotron X-ray imaging of solidification cracking and subsequent analysis of fracture surfaces. Stage 1—Nucleation of inter-granular hot cracks: cracks nucleate inter-granularly in sub-surface where maximum volumetric strain is localized and volume fraction of liquid is less than 0.1; the crack nuclei occur at solute-enriched liquid pockets which remain trapped in increasingly impermeable semi-solid skeleton. Stage 2—Coalescence of cracks via inter-granular fracture: as the applied strain increases, cracks coalesce through inter-granular fracture; the coalescence path is preferential to the direction of the heat source and propagates through the grain boundaries to solidifying dendrites. Stage 3—Propagation through inter-dendritic hot tearing: inter-dendritic hot tearing occurs along the boundaries between solidifying columnar dendrites with higher liquid fraction. It is recommended that future solidification cracking criterion shall be based on the application of multiphase mechanics and fracture mechanics to the failure of semi-solid materials.

Corium spreading: hydrodynamics, rheology and solidification of a high-temperature oxide melt

International Nuclear Information System (INIS)

Journeau, Ch.

2006-06-01

In the hypothesis of a nuclear reactor severe accident, the core could melt and form a high- temperature (2000-3000 K) mixture called corium. In the hypothesis of vessel rupture, this corium would spread in the reactor pit and adjacent rooms as occurred in Chernobyl or in a dedicated core-catcher s in the new European Pressurized reactor, EPR. This thesis is dedicated to the experimental study of corium spreading, especially with the prototypic corium material experiments performed in the VULCANO facility at CEA Cadarache. The first step in analyzing these tests consists in interpreting the material analyses, with the help of thermodynamic modelling of corium solidification. Knowing for each temperature the phase repartition and composition, physical properties can be estimated. Spreading termination is controlled by corium rheological properties in the solidification range, which leads to studying them in detail. The hydrodynamical, rheological and solidification aspects of corium spreading are taken into account in models and computer codes which have been validated against these tests and enable the assessment of the EPR spreading core-catcher concept. (author)

CAN THE CURRICULUM BE USED TO ESTIMATE CRITICAL VELOCITY IN YOUNG COMPETITIVE SWIMMERS?

Directory of Open Access Journals (Sweden)

Daniel A. Marinho

2009-03-01

Full Text Available The aims of the present study were to assess critical velocity using the swimmer curriculum in front crawl events and to compare critical velocity to the velocity corresponding to a 4 mmol·l-1 of blood lactate concentration and to the velocity of a 30 min test. The sample included 24 high level male swimmers ranged between 14 and 16 years old. For each subject the critical velocity, the velocity corresponding to a 4 mmol·l-1 of blood lactate concentration and the mean velocity of a 30 min test were determined. The critical velocity was also estimated by considering the best performance of a swimmer over several distances based on the swimmer curriculum. Critical velocity including 100, 200 and 400 m events was not different from the velocity of 4 mmol·l-1 of blood lactate concentration. Critical velocity including all the swimmer events was not different from the velocity of a 30 min test. The assessment of critical velocity based upon the swimmer curriculum would therefore seem to be a good approach to determine the aerobic ability of a swimmer. The selection of the events to be included in critical velocity assessment must be a main concern in the evaluation of the swimmer

Characterization for solidification and phase transformations of pure-titanium steel weld metal with time-resolved X-ray diffraction system

International Nuclear Information System (INIS)

Terasaki, Hidenori; Komizo, Yu-ichi; Nishino, Fumihiro; Ikeda, Masahiko

2007-01-01

Understanding and controlling solidification and phase transformation process of weld metal is essential for forming the microstructure with superior mechanical property. Recent evolution of analysis technique makes for solidification and phase transformation process to be in-situ analyzed, in direct and reciprocal lattice space. In the present work, unidirectional-solidification and phase transformation in the weld metal of commercial pure-titanium in Gas Tungsten Arc welding was in-situ observed by using Time-Resolved X-Ray Diffraction system with two-dimensional pixel detector. An undulator beam was used as a probe. Larger diffraction area could be detected in the time-resolution of 0.05 seconds, in unidirectional solidification and subsequent phase transformation process of pure-titanium weld metal. Furthermore, the microstructure formation during β-α phase transformation was in situ observed with High temperature Laser Scanning Confocal Microscopy. The crystal configurations in unidirectional solidification of weld metal and rapid change of phase ratio in reconstructive phase transformation were clearly analyzed. (author)

Cross-tail velocity component in the plasma sheet fast flows

Directory of Open Access Journals (Sweden)

N. P. Dmitrieva

2008-06-01

Full Text Available The flux transfer in the magnetotail plasma sheet is mainly provided by the tail-aligned fast plasma flows (Bursty Bulk Flows – BBFs. In this paper we study the events with a large cross-tail velocity component, including their occurrence and relationship to the standard BBFs. We found out that a significant part of large Vy events are a subgroup connected with the BBFs propagation. The maximal deviation of the velocity vector from the X direction (about 40–50 degrees, on average is observed near the BBFs' leading front in the sheath, where the fast flow interacts with surrounding plasma. The average variation of the velocity direction in the vicinity of the BBF resembles a plasma vortex. Our results support the model, in which the BBF represents a polarized, bubble-like flux tube, propagating through the plasma sheet.

Effect and kinetic mechanism of ultrasonic vibration on solidification of 7050 aluminum alloy

Directory of Open Access Journals (Sweden)

Ripeng Jiang

2014-07-01

Full Text Available The work described in this paper dealt with the effect of ultrasonic vibration on the solidification of 7050 aluminum alloy. Two experiments were carried out through introducing ultrasound into the semi-continuous direct-chill (DC casting of aluminum alloy and into alloy solidifying in a crucible, respectively. Results show that ultrasonic vibration can refine grains in the whole cross-section of a billet in the first experiment and is able to increase the cooling rate within the temperature range from 625 °C to 590 °C in the other one. The mechanism of particle resonance caused by ultrasonic vibration was illustrated on the basis of theoretical analysis of the kinetics and energy conversion during the solidification. It is demonstrated that the kinetic energy of resonant particles are mainly from the latent heat energy of solidification, which can shorten the cooling time, inhibit the crystal growth and then lead to the grain refinement.

Relative Contribution of Arms and Legs in 30 s Fully Tethered Front Crawl Swimming

Directory of Open Access Journals (Sweden)

Pedro G. Morouço

2015-01-01

Full Text Available The relative contribution of arm stroke and leg kicking to maximal fully tethered front crawl swimming performance remains to be solved. Twenty-three national level young swimmers (12 male and 11 female randomly performed 3 bouts of 30 s fully tethered swimming (using the whole body, only the arm stroke, and only the leg kicking. A load-cell system permitted the continuous measurement of the exerted forces, and swimming velocity was calculated from the time taken to complete a 50 m front crawl swim. As expected, with no restrictions swimmers were able to exert higher forces than that using only their arm stroke or leg kicking. Estimated relative contributions of arm stroke and leg kicking were 70.3% versus 29.7% for males and 66.6% versus 33.4% for females, with 15.6% and 13.1% force deficits, respectively. To obtain higher velocities, male swimmers are highly dependent on the maximum forces they can exert with the arm stroke (r=0.77, P<0.01, whereas female swimmers swimming velocity is more related to whole-body mean forces (r=0.81, P<0.01. The obtained results point that leg kicking plays an important role over short duration high intensity bouts and that the used methodology may be useful to identify strength and/or coordination flaws.

The Refining Mechanism of Super Gravity on the Solidification Structure of Al-Cu Alloys

Directory of Open Access Journals (Sweden)

Yuhou Yang

2016-12-01

Full Text Available There is far less study of the refining effect of super gravity fields on solidification structures of metals than of the effects of electrical currents, magnetic and ultrasonic fields. Moreover, the refining mechanisms of super gravity are far from clear. This study applied a super gravity field to Al-Cu alloys to investigate its effect on refining their structures and the mechanism of interaction. The experimental results showed that the solidification structure of Al-Cu alloys can be greatly refined by a super gravity field. The major refining effect was mainly achieved when super gravity was applied at the initial solidification stage; only slight refinement could be obtained towards the end of solidification. No refinement was obtained by the super gravity treatment on pure liquid or solid stages. The effectiveness of super gravity results from its promoting the multiplication of crystal nuclei, which we call “Heavy Crystal Rain”, thereby greatly strengthening the migration of crystal nuclei within the alloy. Increasing the solute Cu content can increase nucleation density and restrict the growth of crystals, which further increases the refining effect of super gravity. Within this paper, we also discuss the motile behavior of crystals in a field of super gravity.

Seismic velocity variation along the Izu-Bonin arc estaimated from traveltime tomography using OBS data

Science.gov (United States)

Obana, K.; Tamura, Y.; Takahashi, T.; Kodaira, S.

2014-12-01

The Izu-Bonin (Ogasawara) arc is an intra-oceanic island arc along the convergent plate boundary between the subducting Pacific and overriding Philippine Sea plates. Recent active seismic studies in the Izu-Bonin arc reveal significant along-arc variations in crustal structure [Kodaira et al., 2007]. The thickness of the arc crust shows a remarkable change between thicker Izu (~30 km) and thinner Bonin (~10 km) arcs. In addition to this, several geological and geophysical contrasts, such as seafloor topography and chemical composition of volcanic rocks, between Izu and Bonin arc have been reported [e.g., Yuasa 1992]. We have conducted earthquake observations using ocean bottom seismographs (OBSs) to reveal seismic velocity structure of the crust and mantle wedge in the Izu-Bonin arc and to investigate origin of the along-arc structure variations. We deployed 40 short-period OBSs in Izu and Bonin area in 2006 and 2009, respectively. The OBS data were processed with seismic data recorded at routine seismic stations on Hachijo-jima, Aoga-shima, and Chichi-jima operated by National Research Institute for Earth Science and Disaster Prevention (NIED). More than 5000 earthquakes were observed during about three-months observation period in each experiment. We conducted three-dimensional seismic tomography using manually picked P- and S-wave arrival time data. The obtained image shows a different seismic velocity structures in the mantle beneath the volcanic front between Izu and Bonin arcs. Low P-wave velocity anomalies in the mantle beneath the volcanic front in the Izu arc are limited at depths deeper than those in the Bonin arc. On the other hand, P-wave velocity in the low velocity anomalies beneath volcanic front in the Bonin arc is slower than that in the Izu arc. These large-scale along-arc structure variations in the mantle could relate to the geological and geophysical contrasts between Izu and Bonin arcs.

Measurement of the burning velocity of propane-air mixtures using soap bubbles

Energy Technology Data Exchange (ETDEWEB)

Sakai, Yukio

1988-12-20

By filling a soap bubble with propane-air mixture of spacified equivalence ratio and by igniting it at the center, the flame propagation velocity was measured applying multiplex exposure Schlieren method. And the flow velocity of the unburnt propane-air mixture was also measured by a hot-wire anemometer. From the differences of the above two velocities, the burning velocity was obtained. The values of the burning velocity agreed well with the highly accurate results of usual measurements. The maximum value of the burning velocity, which exists at an equivalence ratio of 1.1, was 50cm/s. This value agreed well with the theoretical calculation result on the on-dimensional flame by Warnatz. The burning velocity in the range of from 0.7 to 1.5 equivalence ratios decreases symmetrically with the maximum value at the center. The velocity decrease in the excessive concentration range of fuel is only a little and converges between 7 and 10 cm/s. To evade the influence of the flame-front instability, measurements were done from 2 to 5cm from the ignition center. Thus accurate values were obtained. 23 refs., 5 figs.

Theoretical modeling of cellular and dendritic solidification microstructures

Science.gov (United States)

Song, Younggil

In this dissertation, we use three-dimensional (3D) phase-field (PF) modeling to investigate (i) 3D solid-liquid interface dynamics observed in microgravity experiments, and (ii) array patterns in a thin-sample geometry. In addition, using the two-dimensional (2D) dendritic-needle-network (DNN) model, we explore (iii) secondary sidebranching dynamics. Recently, solidification experiments are carried out in the DSI (Directional Solidification Insert) of the DECLIC (Device for the study of Critical LIquids and Crystallization) facility aboard the International Space Station (ISS). Thus, the directional solidification experiments are achieved under limited convective currents, and the experimental observations reveal unique dynamics of 3D microstructure in a purely diffusive growth regime. In this directional solidification setup, a temperature field between heat sources could evolve due to two main factors: (i) heat transfer within an adiabatic zone and (ii) latent heat rejection at the interface. These two thermal effects are phenomenologically characterized using a time-dependent thermal shift. In addition, we could quantitatively account for these thermal factors using a numerical calculation of the evolution of temperature field. We introduce these phenomenological and quantitative thermal representations into the PF model. The performed simulations using different thermal descriptions are compared to the experimental measurements from the initial planar interface dynamics to the final spacing selection. The DECLIC-DSI experimental observations exhibit complex grain boundary (GB) dynamics between large grains with a small misorientation. In the observations, several large grains with a small misorientation with respect to the temperature gradient are formed during solidification. Specifically, at a convergent GB, a localized group of misoriented cells penetrates into a nearby grain, which yields the morphological instability of grain boundaries. Remarkably, while

Application of the dual reciprocity boundary element method for numerical modelling of solidification process

Directory of Open Access Journals (Sweden)

E. Majchrzak

2008-12-01

Full Text Available The dual reciprocity boundary element method is applied for numerical modelling of solidification process. This variant of the BEM is connected with the transformation of the domain integral to the boundary integrals. In the paper the details of the dual reciprocity boundary element method are presented and the usefulness of this approach to solidification process modelling is demonstrated. In the final part of the paper the examples of computations are shown.

Solidification of hazardous and mixed radioactive waste at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Boehmer, A.M.; Larsen, M.M.

1986-01-01

EG and G Idaho has initiated a program to develop treatment options for the hazardous and mixed wastes generated at the Idaho National Engineering Laboratory (INEL). This program includes development of solidification methods for some of these wastes. Testing has shown that toxic wastes can be successfully solidified using cement, cement-silicate, or ENVIROSTONE binders to produce nontoxic stable waste forms for safe, long term disposal. This paper presents the results of the solidification development program conducted at the INEL by EG and G Idaho

Solidification of hazardous and mixed radioactive waste at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Boehmer, A.M.; Larsen, M.M.

1986-03-01

EG and G Idaho has initiated a program to develop treatment options for the hazardous and mixed wastes generated at the Idaho National Engineering Laboratory (INEL). This program includes development of solidification methods for some of these wastes. Testing has shown that toxic wastes can be successfully solidified using cement, cement-silicate, or ENVIROSTONE binders to produce nontoxic stable waste forms for safe, long term disposal. This paper presents the results of the solidification development program conducted at the INEL by EG and G Idaho

Method of processing radioactive liquid wastes by solidification with cement

International Nuclear Information System (INIS)

Yasumura, Keijiro; Matsuura, Hiroyuki.

1975-01-01

Object: To subject radioactive liquid wastes to a cement solidification treatment after heating and drying it by a thin film scrape-off drier to render it into the form of power, and then molding it into pellets for the treatment. Structure: Radioactive liquid wastes discharged from a nuclear power plant or nuclear reactor are supplied through a storage tank into a thin film scrape-off drier. In the drier, the radioactive liquid wastes are heated to separate the liquid, and the residue is taken out as dry powder from the scrape-off apparatus. The powder obtained in this way is molded into pellets of a desired form. These pellets are then packed in a drum can or similar container, into which cement paste is then poured for solidification. (Moriyama, K.)

Solidification of high temperature molten salts for thermal energy storage systems

Science.gov (United States)

Sheffield, J. W.

1981-01-01

The solidification of phase change materials for the high temperature thermal energy storage system of an advanced solar thermal power system has been examined theoretically. In light of the particular thermophysical properties of candidate phase change high temperature salts, such as the eutectic mixture of NaF - MgF2, the heat transfer characteristics of one-dimensional inward solidification for a cylindrical geometry have been studied. The Biot number for the solidified salt is shown to be the critical design parameter for constant extraction heat flux. A fin-on-fin design concept of heat transfer surface augmentation is proposed in an effort to minimize the effects of the salt's low thermal conductivity and large volume change upon fusing.

Alternative method of solidification for low-level class a radioactive waste

International Nuclear Information System (INIS)

Mayo, K.S.

1988-01-01

New solidification media have been developed that exhibit excellent spatial efficiency over the entire range of virtually all Class A liquid wastes. These new media are being used to incorporate from 41 to 48 gallons of liquid radioactive waste in a 55-gallon drum. To date, wastes processing at nuclear power plants and facilities include oils, evaporator bottoms, sludges, and ion-exchanges resins as well as combinations of these waste streams. This paper comparatively discusses the performance of solidification agents known as AQUASET TM and PETROSET TM with other currently available agents. It presents key advantages of using the AQUASET and PETROSET media over other media. These advantages include improvements in packaging efficiency, leachability, and repeatability

Joining of superalloy Inconel 600 by diffusion induced isothermal solidification of a liquated insert metal

International Nuclear Information System (INIS)

Egbewande, A.T.; Chukwukaeme, C.; Ojo, O.A.

2008-01-01

The effect of process variables on the microstructure of transient liquid phase bonded IN 600 using a commercial filler alloy was studied. Microstructural examination of bonded specimens showed that isothermal solidification of the liquated insert occurred during holding at the joining temperatures. In cases where the holding time was insufficient for complete isothermal solidification, the residual liquid transformed on cooling into a centerline eutectic product. The width of the eutectic decreased with increased holding time and an increase in initial gap width resulted in thicker eutectic width in specimens bonded at the same temperature and for equivalent holding times. In addition to the centerline eutectic microconstituent, precipitation of boron-rich particles was observed within the base metal region adjacent to the substrate-joint interface. Formation of these particles appeared to have influenced the rate of solidification of the liquated interlayer during bonding. In contrast to the conventional expectation of an increase in the rate of isothermal solidification with an increase in temperature, a decrease in the rate was observed with an increase in temperatures above 1160 deg. C. This could be related to a decrease in solubility of boron in nickel above the Ni-B eutectic temperature

Real-time X-ray transmission microscopy for fundamental studies solidification: Al-Al2Au eutectic

International Nuclear Information System (INIS)

Curreri, Peter A.; Kaukler, William F.; Sen, Subhayu

1998-01-01

High resolution real-time X-ray Transmission Microscopy, XTM, has been applied to obtain information fundamental to solidification of optically opaque metallic systems. We have previously reported the measurement of the solute profile in the liquid, phase growth, and detailed solid-liquid interfacial morphology of aluminum based alloys with exposure times less than 2 seconds. Recent advances in XTM furnace design have provided an increase in real-time magnification (during solidification) for the XTM from 40X to 160X. The increased magnification has enabled for the first time the XTM imaging of real-time growth of fibers and particles with diameters of 5 μm. We have previously applied this system to study the kinetics of formation and morphological evolution of secondary fibers and particles in Al-Bi monotectic alloys. In this paper we present the preliminary results of the first real-time observations of fiber morphology evolution in optically opaque bulk metal sample of Aluminum-Gold eutectic alloy. These studies show that the XTM can be applied to study the fundamentals of eutectic and monotectic solidification. We are currently attempting to apply this technology in the fundamentals of solidification in microgravity

Integrated System of Thermal/Dimensional Analysis for Quality Control of Metallic Melt and Ductile Iron Casting Solidification

Science.gov (United States)

Stan, Stelian; Chisamera, Mihai; Riposan, Iulian; Neacsu, Loredana; Cojocaru, Ana Maria; Stan, Iuliana

2018-03-01

The main objective of the present work is to introduce a specific experimental instrument and technique for simultaneously evaluating cooling curves and expansion or contraction of cast metals during solidification. Contraction/expansion analysis illustrates the solidification parameters progression, according to the molten cast iron characteristics, which are dependent on the melting procedure and applied metallurgical treatments, mold media rigidity and thermal behavior [heat transfer parameters]. The first part of the paper summarizes the performance of this two-mold device. Its function is illustrated by representative shrinkage tendency results in ductile cast iron as affected by mold rigidity (green sand and furan resin sand molds) and inoculant type (FeSi-based alloys), published in part previously. The second part of the paper illustrates an application of this equipment adapted for commercial foundry use. It conducts thermal analysis and volume change measurements in a single ceramic cup so that mold media as well as solidification conditions are constants, with cast iron quality as the variable. Experiments compared gray and ductile cast iron solidification patterns. Gray iron castings are characterized by higher undercooling at the beginning and at the end of solidification and lower graphitic expansion. Typically, ductile cast iron exhibits higher graphitic, initial expansion, conducive for shrinkage formation in soft molds.

Experimental analysis of an oblique turbulent flame front propagating in a stratified flow

Energy Technology Data Exchange (ETDEWEB)

Galizzi, C.; Escudie, D. [Universite de Lyon, CNRS, CETHIL, INSA-Lyon, UMR5008, F-69621 Cedex (France)

2010-12-15

This paper details the experimental study of a turbulent V-shaped flame expanding in a nonhomogeneous premixed flow. Its aim is to characterize the effects of stratification on turbulent flame characteristics. The setup consists of a stationary V-shaped flame stabilized on a rod and expanding freely in a lean premixed methane-air flow. One of the two oblique fronts interacts with a stratified slice, which has an equivalence ratio close to one and a thickness greater than that of the flame front. Several techniques such as PIV and CH{sup *} chemiluminescence are used to investigate the instantaneous fields, while laser Doppler anemometry and thermocouples are combined with a concentration probe to provide information on the mean fields. First, in order to provide a reference, the homogeneous turbulent case is studied. Next, the stratified turbulent premixed flame is investigated. Results show significant modifications of the whole flame and of the velocity field upstream of the flame front. The analysis of the geometric properties of the stratified flame indicates an increase in flame brush thickness, closely related to the local equivalence ratio. (author)

Initial stages of solidification of eutectic alloys

International Nuclear Information System (INIS)

Lemaignan, Clement

1980-01-01

The study of the various initial stages of eutectic solidification - i.e. primary nucleation, eutectic structure formation and stable growth conditions - was undertaken with various techniques including low angle neutron diffusion, in-situ electron microscopy on solidifying alloys and classical metallography. The results obtained allow to discuss the effect of metastable states during primary nucleation, of surface dendrite during eutectic nucleation and also of the crystallographic anisotropy during growth. (author) [fr

Rapid solidification for preparation of high Tc superconductors

International Nuclear Information System (INIS)

Yavari, A.R.

1988-01-01

High Tc superconducting oxides are prepared in two different ways using rapid solidification: by oxidation of microcrystalline or amorphous tapes obtained by quenching the liquid alloy and via crystallisation of the amorphous oxide obtained by rapid quenching of the oxide melt. This technique is applied for the first time to the BiCaSrCuO family [fr

Particle Trapping and Banding in Rapid Colloidal Solidification

KAUST Repository

Elliott, J. A. W.

2011-10-11

We derive an expression for the nonequilibrium segregation coefficient of colloidal particles near a moving solid-liquid interface. The resulting kinetic phase diagram has applications for the rapid solidification of clay soils, gels, and related colloidal systems. We use it to explain the formation of bandlike defects in rapidly solidified alumina suspensions. © 2011 American Physical Society.

Corium spreading: hydrodynamics, rheology and solidification of a high-temperature oxide melt; L'etalement du corium: hydrodynamique, rheologie et solidification d'unbain d'oxydes a haute temperature

Energy Technology Data Exchange (ETDEWEB)

Journeau, Ch

2006-06-15

In the hypothesis of a nuclear reactor severe accident, the core could melt and form a high- temperature (2000-3000 K) mixture called corium. In the hypothesis of vessel rupture, this corium would spread in the reactor pit and adjacent rooms as occurred in Chernobyl or in a dedicated core-catcher s in the new European Pressurized reactor, EPR. This thesis is dedicated to the experimental study of corium spreading, especially with the prototypic corium material experiments performed in the VULCANO facility at CEA Cadarache. The first step in analyzing these tests consists in interpreting the material analyses, with the help of thermodynamic modelling of corium solidification. Knowing for each temperature the phase repartition and composition, physical properties can be estimated. Spreading termination is controlled by corium rheological properties in the solidification range, which leads to studying them in detail. The hydrodynamical, rheological and solidification aspects of corium spreading are taken into account in models and computer codes which have been validated against these tests and enable the assessment of the EPR spreading core-catcher concept. (author)

Experimental Investigation of Multi-layer Insulation Effect on Damage of Stuffed Shield by High-velocity Impact

Directory of Open Access Journals (Sweden)

GUAN Gong-shun

2016-09-01

Full Text Available The stuffed shield with multi-layer insulation(MLI was designed by improving on Al Whipple shield, and a series of high-velocity impact tests were practiced with a two-stage light gas gun facility at vacuum environment. The damage model of the stuffed shield with different MLI location by Al-sphere projectile impacting was obtained. The effect of MLI on damage of the stuffed shield by high-velocity impact was studied. The results indicate when the MLI is located at front side of the first Al-plate, the protection performance of the stuffed shield is improved with the larger perforation diameter of the first Al-plate and more impact kinetic energy dissipation of the projectile. When MLI is arranged at back side of the first Al-plate, the expansion of the secondary debris cloud from projectile impacting the first Al-plate is restrained, it is not good to improve the protection performance of the stuffed shield. When MLI is arranged at front side of the stuffed wall, the perforation size of the stuffed wall increases; when MLI is arranged at front side of the rear wall, the distribution range of crater on the rear wall decreases.

Solidification structure and dispersoids in rapidly solidified Ti-Al-Sn-Zr-Er-B alloys

International Nuclear Information System (INIS)

Rowe, R.G.; Broderick, T.F.; Koch, E.F.; Froes, F.H.

1986-01-01

The microstructure of melt extracted and melt spun titanium alloys containing erbium and boron revealed a duplex solidification structure of columnar grains leading to equiaxed and dendritic structures near the free surface of melt extracted and melt spun alloys. The solidification structure was revealed by apparent boride segregation to cellular, interdendritic and grain boundaries. Precipitation of needle or lath-like TiB particles occurred adjacent to Er/sub 2/O/sub 3/ dispesoid particles in as-rapidly solidified ribbon

Effect of blended materials on U(VI) retention characteristics for portland cement solidification product

International Nuclear Information System (INIS)

Tan Hongbin; Ma Xiaoling; Li Yuxiang

2006-01-01

Using the simulated groundwater as leaching liquid, the retention capability of U(VI) in solidification products with Portland cement, the Portland cement containing silica fume, the Portland cement containing metakaolin and the Portland cement containing fly ash was researched by leaching experiments at 25 degree C for 42 d. The results indicate silica fume and metakaolin as blended materials can improve the U(VI) retention capability of Portland cement solidification product, but fly ash can not. (authors)

Study and modeling of heat transfer during the solidification of semi-crystalline polymers

Energy Technology Data Exchange (ETDEWEB)

Le Goff, R.; Poutot, G.; Delaunay, D. [Laboratoire de Thermocinetique de l' ecole polytechnique de l' universite de Nantes, UMR CNRS 6607, rue Christian Pauc, BP 50609 44306 Nantes cedex 3 (France); Fulchiron, R.; Koscher, E. [Laboratoire des Materiaux Polymeres et des Biomateriaux, IMP/UMR CNRS 5627, Universite Claude Bernard, Lyon 1, 69622 Villeurbanne Cedex (France)

2005-12-01

Semi-crystalline polymers are materials whose behavior during their cooling is difficult to model because of the strong coupling between the crystallization, heat transfer, pressure and shear. Thanks to two original apparatus we study solidification of such a polymer without shear. Firstly the comparison between experimental results and a numerical model will permit to validate crystallization kinetic for cooling rate reachable by DSC. The second experiment makes it possible to analyze solidification for high cooling rate, corresponding to some manufacturing processes. It appears that crystallization has an influence on the thermal contact resistance. (author)

Hazardous and mixed waste solidification development conducted at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Boehmer, A.M.; Larsen, M.M.

1986-04-01

EG and G Idaho, Inc., has initiated a program to develop safe, efficient, cost-effective solidification treatment methods for the disposal of some of the hazardous and mixed wastes generated at the Idaho National Engineering Laboratory (INEL). Testing has shown that Extraction Procedure (EP) toxic wastes can be successfully solidified using cement, cement-silicate, or ENVIROSTONE binders to produce nontoxic stable waste forms for safe, long-term disposal as general or low-level waste, depending upon the radioactivity. The results of the solidification development program are presented in this report

Measurements of the laminar burning velocity of hydrogen-air premixed flames

Energy Technology Data Exchange (ETDEWEB)

Pareja, Jhon; Burbano, Hugo J. [Science and Technology of Gases and Rational Use of Energy Group, Faculty of Engineering, University of Antioquia, Calle 67 N 53, 108 Bloque 20, 447 Medellin (Colombia); Ogami, Yasuhiro [Institute of Fluid Science, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai, Miyagi 980-8577 (Japan)

2010-02-15

Experimental and numerical studies on laminar burning velocities of hydrogen-air mixtures were performed at standard pressure and room temperature varying the equivalence ratio from 0.8 to 3.0. The flames were generated using a contoured slot-type nozzle burner (4 mm x 10 mm). Measurements of laminar burning velocity were conducted using particle tracking velocimetry (PTV) combined with Schlieren photography. This technique provides the information of instantaneous local burning velocities in the whole region of the flame front, and laminar burning velocities were determined using the mean value of local burning velocities in the region of non-stretch. Additionally, average laminar burning velocities were determined using the angle method and compared with the data obtained with the PTV method. Numerical calculations were also conducted using detailed reaction mechanisms and transport properties. The experimental results from the PTV method are in good agreement with the numerical results at every equivalence ratio of the range of study. Differences between the results obtained with the angle method and those with the PTV method are reasonably small when the effects of flame stretch and curvature are reduced by using a contoured slot-type nozzle. (author)

Superconducting accelerating structures for very low velocity ion beams

Directory of Open Access Journals (Sweden)

J. Xu

2008-03-01

Full Text Available This paper presents designs for four types of very-low-velocity superconducting (SC accelerating cavity capable of providing several MV of accelerating potential per cavity, and suitable for particle velocities in the range 0.006velocity profile to maximize the output energy for each of a number of different ion species. Several laboratories in the U.S. and Europe are planning exotic beam facilities based on SC linacs. The cavity designs presented here are intended for the front end of such linacs, particularly for the postacceleration of rare isotopes of low charge state. Several types of SC cavities have been developed recently to cover particle velocities above 0.06c. Superconducting four-gap quarter-wave resonators for velocities 0.008<β=v/c<0.05 were developed about two decades ago and have been successfully operated at the ATLAS SC linac at Argonne National Laboratory. Since that time, progress in simulation tools, cavity fabrication, and processing have increased SC cavity gradients by a factor of 3–4. This paper applies these tools to optimize the design of a four-gap quarter-wave resonator for exotic beam facilities and other low-velocity applications.

Superconducting accelerating structures for very low velocity ion beams

Energy Technology Data Exchange (ETDEWEB)

Xu, J.; Shepard, K.W.; Ostroumov, P.N.; Fuerst, J.D.; Waldschmidt, G.; /Argonne; Gonin, I.V.; /Fermilab

2008-01-01

This paper presents designs for four types of very-low-velocity superconducting accelerating cavity capable of providing several MV of accelerating potential per cavity, and suitable for particle velocities in the range 0.006 < v/c < 0.06. Superconducting TEM-class cavities have been widely applied to CW acceleration of ion beams. SC linacs can be formed as an array of independently-phased cavities, enabling a variable velocity profile to maximize the output energy for each of a number of different ion species. Several laboratories in the US and Europe are planning exotic beam facilities based on SC linacs. The cavity designs presented here are intended for the front-end of such linacs, particularly for the post-acceleration of rare isotopes of low charge state. Several types of SC cavities have been developed recently to cover particle velocities above 0.06c. Superconducting four-gap quarter-wave resonators for velocities 0.008 < {beta} = v/c < 0.05 were developed about two decades ago and have been successfully operated at the ATLAS SC linac at Argonne National Laboratory. Since that time, progress in simulation tools, cavity fabrication and processing have increased SC cavity gradients by a factor of 3-4. This paper applies these tools to optimize the design of a four-gap quarter-wave resonator for exotic beam facilities and other low-velocity applications.

On an upwelling front, propagation of upwelling and vertical velocity in the eastern Arabian sea during monsoon, 1987

Digital Repository Service at National Institute of Oceanography (India)

Antony, M.K.; Unnikrishnan, A.S.

A coastal upwelling front parallel to the coast and identifiable upto a depth of 75 m was observed between 12.5 and 16 degrees N along the eastern Arabian Sea in September, 1987 from closely spaced digital BT data. With a north-south slope...

Estimating front-wave velocity of infectious diseases: a simple, efficient method applied to bluetongue.

Science.gov (United States)

Pioz, Maryline; Guis, Hélène; Calavas, Didier; Durand, Benoît; Abrial, David; Ducrot, Christian

2011-04-20

Understanding the spatial dynamics of an infectious disease is critical when attempting to predict where and how fast the disease will spread. We illustrate an approach using a trend-surface analysis (TSA) model combined with a spatial error simultaneous autoregressive model (SAR(err) model) to estimate the speed of diffusion of bluetongue (BT), an infectious disease of ruminants caused by bluetongue virus (BTV) and transmitted by Culicoides. In a first step to gain further insight into the spatial transmission characteristics of BTV serotype 8, we used 2007-2008 clinical case reports in France and TSA modelling to identify the major directions and speed of disease diffusion. We accounted for spatial autocorrelation by combining TSA with a SAR(err) model, which led to a trend SAR(err) model. Overall, BT spread from north-eastern to south-western France. The average trend SAR(err)-estimated velocity across the country was 5.6 km/day. However, velocities differed between areas and time periods, varying between 2.1 and 9.3 km/day. For more than 83% of the contaminated municipalities, the trend SAR(err)-estimated velocity was less than 7 km/day. Our study was a first step in describing the diffusion process for BT in France. To our knowledge, it is the first to show that BT spread in France was primarily local and consistent with the active flight of Culicoides and local movements of farm animals. Models such as the trend SAR(err) models are powerful tools to provide information on direction and speed of disease diffusion when the only data available are date and location of cases.

Solidification of AM and AZ magnesium alloys characterized by heat-transfer modeled thermal and calorimetric analysis and microsegregation study of directionally solidified microstructure

Energy Technology Data Exchange (ETDEWEB)

Mirkovic, Djordje

2008-05-09

The micro-scale solidification of commercial Mg alloys of the AZ and AM series is in the focus of the present thesis. Two approaches of investigating solidification are implemented, complementary regarding temperature gradient and solidification rate, and also with respect to the generated microstructure. The first approach considers solidification under a negligible spatial temperature gradient. Here the solidification curves, i.e. fraction solid versus temperature, were determined by developing an improved heat-transfer modeling applicable on both differential thermal analysis (DTA) and differential scanning calorimetry (DSC) signals. The correlation between solidification enthalpy and fraction solid during solidification was tested in detail. A better evaluation of the measured DTA and DSC signals is attained through an independent measurement of the time constant as function of temperature for the applied equipment. A further improvement is achieved through a more impartial interpretation of the measured curves. Both improvements enable a better desmearing of measured signals and reduce the error induced by the operator. The novel tantalum encapsulation enabled appropriate handling of challenging Mg-alloys. The viability and limitations of thermal analysis in general to determine start and end of solidification of AZ magnesium alloys was also studied. The second approach is based on directional solidification in a high temperature gradient and at constant solidification rate, achieved by the Bridgman technique. The resulting dendritic microstructure and inherent microsegregation are studied in this work. The solute profiles, i.e. solute content versus solid phase fraction during solidification, are determined by an advanced treatment of the EPMA data. Problems that are demonstrated in this work are Al-loss and melt pollution due to reaction with typical sample container material made of unprotected steel. The development of an optimized boron nitride (BN

Solidification microstructure of centrifugally cast Inconel 625

Directory of Open Access Journals (Sweden)

Silvia Barella

2017-07-01

Full Text Available Centrifugal casting is a foundry process allowing the production of near net-shaped axially symmetrical components. The present study focuses on the microstructural characterization of centrifugally cast alloys featuring different chemical compositions for the construction of spheres applied in valves made of alloy IN625 for operation at high pressure. Control of the solidification microstructure is needed to assure the reliability of the castings. Actually, a Ni-base superalloy such as this one should have an outstanding combination of mechanical properties, high temperature stability and corrosion resistance. Alloys such as IN625 are characterised by a large amount of alloying elements and a wide solidification range, so they can be affected by micro-porosity defects, related to the shrinkage difference between the matrix and the secondary reinforcing phases (Nb-rich carbides and Laves phase. In this study, the microstructure characterization was performed as a function of the applied heat treatments and it was coupled with a calorimetric analysis in order to understand the mechanism ruling the formation of micro-porosities that can assure alloy soundness. The obtained results show that the presence of micro-porosities is governed by morphology and by the size of the secondary phases, and the presence of the observed secondary phases is detrimental to corrosion resistance.

Amphibious Shear Velocity Structure of the Cascadia Subduction Zone

Science.gov (United States)

Janiszewski, H. A.; Gaherty, J. B.; Abers, G. A.; Gao, H.

2017-12-01

The amphibious Cascadia Initiative crosses the coastline of the Cascadia subduction zone (CSZ) deploying seismometers from the Juan de Fuca ridge offshore to beyond the volcanic arc onshore. This allows unprecedented seismic imaging of the CSZ, enabling examination of both the evolution of the Juan de Fuca plate prior to and during subduction as well as the along strike variability of the subduction system. Here we present new results from an amphibious shear velocity model for the crust and upper mantle across the Cascadia subduction zone. The primary data used in this inversion are surface-wave phase velocities derived from ambient-noise Rayleigh-wave data in the 10 - 20 s period band, and teleseismic earthquake Rayleigh wave phase velocities in the 20 - 160 s period band. Phase velocity maps from these data reflect major tectonic structures including the transition from oceanic to continental lithosphere, Juan de Fuca lithosphere that is faster than observations in the Pacific for oceanic crust of its age, slow velocities associated with the accretionary prism, the front of the fast subducting slab, and the Cascades volcanic arc which is associated with slower velocities in the south than in the north. Crustal structures are constrained by receiver functions in the offshore forearc and onshore regions, and by active source constraints on the Juan de Fuca plate prior to subduction. The shear-wave velocities are interpreted in their relationships to temperature, presence of melt or hydrous alteration, and compositional variation of the CSZ.

A coupled model on fluid flow, heat transfer and solidification in continuous casting mold

Directory of Open Access Journals (Sweden)

Xu-bin Zhang

2017-11-01

Full Text Available Fluid flow, heat transfer and solidification of steel in the mold are so complex but crucial, determining the surface quality of the continuous casting slab. In the current study, a 2D numerical model was established by Fluent software to simulate the fluid flow, heat transfer and solidification of the steel in the mold. The VOF model and k-ε model were applied to simulate the flow field of the three phases (steel, slag and air, and solidification model was used to simulate the solidification process. The phenomena at the meniscus were also explored through interfacial tension between the liquid steel and slag as well as the mold oscillation. The model included a 20 mm thick mold to clarify the heat transfer and the temperature distribution of the mold. The simulation results show that the liquid steel flows as upper backflow and lower backflow in the mold, and that a small circulation forms at the meniscus. The liquid slag flows away from the corner at the meniscus or infiltrates into the gap between the mold and the shell with the mold oscillating at the negative strip stage or at the positive strip stage. The simulated pitch and the depth of oscillation marks approximate to the theoretical pitch and measured depth on the slab.

Economic analysis of a volume reduction/polyethylene solidification system for low-level radioactive wastes

International Nuclear Information System (INIS)

Kalb, P.D.; Colombo, P.

1985-01-01

A study was conducted at Brookhaven National Laboratory to determine the economic feasibility of a fluidized bed volume reduction/polyethylene solidification system for low-level radioactive wastes. These results are compared with the ''null'' alternative of no volume reduction and solidification of aqueous waste streams in hydraulic cement. The economic analysis employed a levelized revenue requirement (LRR) technique conducted over a ten year period. An interactive computer program was written to conduct the LRR calculations. Both of the treatment/solidification options were considered for a number of scenarios including type of plant (BWR or PWR) and transportation distance to the disposal site. If current trends in the escalation rates of cost components continue, the volume reduction/polyethylene solidification option will be cost effective for both BWRs and PWRs. Data indicate that a minimum net annual savings of $0.8 million per year (for a PWR shipping its waste 750 miles) and a maximum net annual savings of $9 million per year (for a BWR shipping its waste 2500 miles) can be achieved. A sensitivity analysis was performed for the burial cost escalation rate, which indicated that variation of this factor will impact the total levelized revenue requirement. The burial cost escalation rate which yields a break-even condition was determined for each scenario considered. 11 refs., 8 figs., 39 tabs

Solidification as low cost technology prior to land filling of industrial hazardous waste sludge.

Science.gov (United States)

El-Sebaie, O; Ahmed, M; Ramadan, M

2000-01-01

The aim of this study is to stabilize and solidify two different treated industrial hazardous waste sludges, which were selected from factories situated close to Alexandria. They were selected to ensure their safe transportation and landfill disposal by reducing their potential leaching of hazardous elements, which represent significant threat to the environment, especially the quality of underground water. The selected waste sludges have been characterized. Ordinary Portland Cement (OPC), Cement Kiln Dust (CKD) from Alexandria Portland Cement Company, and Calcium Sulphate as a by-product from the dye industry were used as potential solidification additives to treat the selected treated waste sludges from tanning and dyes industry. Waste sludges as well as the solidified wastes have been leach-tested, using the General Acid Neutralization Capacity (GANC) procedure. Concentration of concerning metals in the leachates was determined to assess changes in the mobility of major contaminants. The treated tannery waste sludge has an acid neutralization capacity much higher than that of the treated dyes waste sludge. Experiment results demonstrated the industrial waste sludge solidification mix designs, and presented the reduction of contaminant leaching from two types of waste sludges. The main advantages of solidification are that it is simple and low cost processing which includes readily available low cost solidification additives that will convert industrial hazardous waste sludges into inert materials.

Elemental analysis of the Al-Fe intermetallic prepared by fast solidification

International Nuclear Information System (INIS)

Sandoval J, R.A.; Lopez M, J.; Ramirez T, J.J.; Aspiazu F, J.; Villasenor S, P.

2003-01-01

Applying the PIXE technique samples of the Al-Fe intermetallic prepared by fast solidification, obtained starting from Al recycled were analyzed. The concentrations of the found elements are given. (Author)

Light-Front Holography, Light-Front Wavefunctions, and Novel QCD Phenomena

Energy Technology Data Exchange (ETDEWEB)

Brodsky, Stanley J.; /SLAC /Southern Denmark U., CP3-Origins; de Teramond, Guy F.; /Costa Rica U.

2012-02-16

Light-Front Holography is one of the most remarkable features of the AdS/CFT correspondence. In spite of its present limitations it provides important physical insights into the nonperturbative regime of QCD and its transition to the perturbative domain. This novel framework allows hadronic amplitudes in a higher dimensional anti-de Sitter (AdS) space to be mapped to frame-independent light-front wavefunctions of hadrons in physical space-time. The model leads to an effective confining light-front QCD Hamiltonian and a single-variable light-front Schroedinger equation which determines the eigenspectrum and the light-front wavefunctions of hadrons for general spin and orbital angular momentum. The coordinate z in AdS space is uniquely identified with a Lorentz-invariant coordinate {zeta} which measures the separation of the constituents within a hadron at equal light-front time and determines the off-shell dynamics of the bound-state wavefunctions, and thus the fall-off as a function of the invariant mass of the constituents. The soft-wall holographic model modified by a positive-sign dilaton metric, leads to a remarkable one-parameter description of nonperturbative hadron dynamics - a semi-classical frame-independent first approximation to the spectra and light-front wavefunctions of meson and baryons. The model predicts a Regge spectrum of linear trajectories with the same slope in the leading orbital angular momentum L of hadrons and the radial quantum number n. The hadron eigensolutions projected on the free Fock basis provides the complete set of valence and non-valence light-front Fock state wavefunctions {Psi}{sub n/H} (x{sub i}, k{sub {perpendicular}i}, {lambda}{sub i}) which describe the hadron's momentum and spin distributions needed to compute the direct measures of hadron structure at the quark and gluon level, such as elastic and transition form factors, distribution amplitudes, structure functions, generalized parton distributions and transverse

Neutron radiography for visualization of liquid metal processes: bubbly flow for CO2 free production of Hydrogen and solidification processes in EM field

Science.gov (United States)

Baake, E.; Fehling, T.; Musaeva, D.; Steinberg, T.

2017-07-01

The paper describes the results of two experimental investigations aimed to extend the abilities of a neutron radiography to visualize two-phase processes in the electromagnetically (EM) driven melt flow. In the first experiment the Argon bubbly flow in the molten Gallium - a simulation of the CO2 free production of Hydrogen process - was investigated and visualized. Abilities of EM stirring for control on the bubbles residence time in the melt were tested. The second experiment was directed to visualization of a solidification front formation under the influence of EM field. On the basis of the neutron shadow pictures the form of growing ingot, influenced by turbulent flows, was considered. In the both cases rotating permanent magnets were agitating the melt flow. The experimental results have shown that the neutron radiography can be successfully employed for obtaining the visual information about the described processes.

Solidification of ion-exchange resins by hydrothermal hot-pressing

International Nuclear Information System (INIS)

Kaneko, M.

1993-01-01

The solidification reaction which easily occurs while continuously keeping the mixture of cation and anion exchange resins compressed under hydrothermal conditions has been demonstrated. Dehydration was considered to occur between sulphonic acid (-SO 3 H) from the cation exchange resin and quaternary ammonium [-CH 2 -N(CH 3 ) 3 OH] from anion-exchange resin-on terminal groups. The cation-and anion-exchange resins were mixed in a 1:1 weight ratio, put in a hot-pressing autoclave and compressed between pistons from the top and bottom at 600 kg cm -2 pressure. The material was continuously compressed during hydrothermal treatment at 200 kg cm -2 by a hydraulic jack and heated to a desired temperature with an induction heater. This system could be used for rapid temperature increasing up to 30 o c min -1 . The pressure and temperature were kept constant for 10 min. The autoclave was cooled to room temperature after the hydrothermal treatment. After the specimen was taken out, the ion-exchange radical reactions were estimated and the product structures were examined. The cation- and anion-exchange resin mixture was solidified. The resultant solidified body at a 300 o C reaction condition for 10 min had a 1.0 g cm -3 density and 700 kg cm -2 compressive strength, and the weight loss did not change in distilled water for 2 weeks. On the other hand, a solidification reaction did not occur at below 250 o C when only the cation or anion was solidified, but they were decomposed. These results suggest that a mixture of cation- and anion-exchange resins causes a solidification reaction under hydrothermal hot-pressing conditions at 300 o C. (author)

Rock solidification method

International Nuclear Information System (INIS)

Nakaya, Iwao; Murakami, Tadashi; Miyake, Takafumi; Funakoshi, Toshio; Inagaki, Yuzo; Hashimoto, Yasuhide.

1985-01-01

Purpose: To convert radioactive wastes into the final state for storage (artificial rocks) in a short period of time. Method: Radioactive burnable wastes such as spent papers, cloths and oils and activated carbons are burnt into ashes in a burning furnace, while radioactive liquid wastes such as liquid wastes of boric acid, exhausted cleaning water and decontaminating liquid wastes are powderized in a drying furnace or calcining furnace. These powders are joined with silicates as such as white clay, silica and glass powder and a liquid alkali such as NaOH or Ca(OH) 2 and transferred to a solidifying vessel. Then, the vessel is set to a hydrothermal reactor, heated and pressurized, then taken out about 20 min after and tightly sealed. In this way, radioactive wastes are converted through the hydrothermal reactions into aqueous rock stable for a long period of time to obtain solidification products insoluble to water and with an extremely low leaching rate. (Ikeda, J.)

Survey of agents and techniques applicable to the solidification of low-level radioactive wastes

International Nuclear Information System (INIS)

Fuhrmann, M.; Neilson, R.M. Jr.; Colombo, P.

1981-12-01

A review of the various solidification agents and techniques that are currently available or potentially applicable for the solidification of low-level radioactive wastes is presented. An overview of the types and quantities of low-level wastes produced is presented. Descriptions of waste form matrix materials, the wastes types for which they have been or may be applied and available information concerning relevant waste form properties and characteristics follow. Also included are descriptions of the processing techniques themselves with an emphasis on those operating parameters which impact upon waste form properties. The solidification agents considered in this survey include: hydraulic cements, thermoplastic materials, thermosetting polymers, glasses, synthetic minerals and composite materials. This survey is part of a program supported by the United States Department of Energy's Low-Level Waste Management Program (LLWMP). This work provides input into LLWMP efforts to develop and compile information relevant to the treatment and processing of low-level wastes and their disposal by shallow land burial

Survey of agents and techniques applicable to the solidification of low-level radioactive wastes

Energy Technology Data Exchange (ETDEWEB)

Fuhrmann, M.; Neilson, R.M. Jr.; Colombo, P.

1981-12-01

A review of the various solidification agents and techniques that are currently available or potentially applicable for the solidification of low-level radioactive wastes is presented. An overview of the types and quantities of low-level wastes produced is presented. Descriptions of waste form matrix materials, the wastes types for which they have been or may be applied and available information concerning relevant waste form properties and characteristics follow. Also included are descriptions of the processing techniques themselves with an emphasis on those operating parameters which impact upon waste form properties. The solidification agents considered in this survey include: hydraulic cements, thermoplastic materials, thermosetting polymers, glasses, synthetic minerals and composite materials. This survey is part of a program supported by the United States Department of Energy's Low-Level Waste Management Program (LLWMP). This work provides input into LLWMP efforts to develop and compile information relevant to the treatment and processing of low-level wastes and their disposal by shallow land burial.

Reconstruction of piano hammer force from string velocity.

Science.gov (United States)

Chaigne, Antoine

2016-11-01

A method is presented for reconstructing piano hammer forces through appropriate filtering of the measured string velocity. The filter design is based on the analysis of the pulses generated by the hammer blow and propagating along the string. In the five lowest octaves, the hammer force is reconstructed by considering two waves only: the incoming wave from the hammer and its first reflection at the front end. For the higher notes, four- or eight-wave schemes must be considered. The theory is validated on simulated string velocities by comparing imposed and reconstructed forces. The simulations are based on a nonlinear damped stiff string model previously developed by Chabassier, Chaigne, and Joly [J. Acoust. Soc. Am. 134(1), 648-665 (2013)]. The influence of absorption, dispersion, and amplitude of the string waves on the quality of the reconstruction is discussed. Finally, the method is applied to real piano strings. The measured string velocity is compared to the simulated velocity excited by the reconstructed force, showing a high degree of accuracy. A number of simulations are compared to simulated strings excited by a force derived from measurements of mass and acceleration of the hammer head. One application to an historic piano is also presented.

Exploiting LSPIV to assess debris-flow velocities in the field

Science.gov (United States)

Theule, Joshua I.; Crema, Stefano; Marchi, Lorenzo; Cavalli, Marco; Comiti, Francesco

2018-01-01

The assessment of flow velocity has a central role in quantitative analysis of debris flows, both for the characterization of the phenomenology of these processes and for the assessment of related hazards. Large-scale particle image velocimetry (LSPIV) can contribute to the assessment of surface velocity of debris flows, provided that the specific features of these processes (e.g. fast stage variations and particles up to boulder size on the flow surface) are taken into account. Three debris-flow events, each of them consisting of several surges featuring different sediment concentrations, flow stages, and velocities, have been analysed at the inlet of a sediment trap in a stream in the eastern Italian Alps (Gadria Creek). Free software has been employed for preliminary treatment (orthorectification and format conversion) of video-recorded images as well as for LSPIV application. Results show that LSPIV velocities are consistent with manual measurements of the orthorectified imagery and with front velocity measured from the hydrographs in a channel recorded approximately 70 m upstream of the sediment trap. Horizontal turbulence, computed as the standard deviation of the flow directions at a given cross section for a given surge, proved to be correlated with surface velocity and with visually estimated sediment concentration. The study demonstrates the effectiveness of LSPIV in the assessment of surface velocity of debris flows and permit the most crucial aspects to be identified in order to improve the accuracy of debris-flow velocity measurements.

Role of ionization fronts in the colliding wind model of planetary nebulae

International Nuclear Information System (INIS)

Giuliani, J.L. Jr.

1981-01-01

A similarity transformation is used to study the expansion of a planetary nebula which is driven by a fast stellar wind as well as an expanding H II region. The undisturbed gas is taken to be the remnant of a slow, red giant wind. The present analysis improves upon Kwok, Purton, and FitzGerald's colliding wind model for the formation of planetary nebulae since it includes the dynamical influence of ionization fronts, and calculates the variation of velocity and density within the flow

Simulation of continuous cast steel product solidification

Directory of Open Access Journals (Sweden)

Ardelean, E.

2007-06-01

Full Text Available Primary cooling – inside the tundish – has a great impact over the thickness of the solidified steel crust. If on exiting the tundish the crust is too thin, it can punch and break, as a result of the ferrostatic pressure exerted from the inside by the liquid steel as well as because of the weight of the molten steel. The parameters that influence the amount of dissipated heat depend on the cooling water flow of the tundish, on the pressure and temperature of the cooling water but also on the overheating of the continuously cast steel. The secondary cooling takes place at the exit of the semi-finished product from the tundish, when the solidification is supposed to take place all along the cross section of the strand. In order to achieve it, in addition to a correctly managed primary cooling, it is necessary to obtain the proper correlation of the factors that influence the secondary cooling as well: the water flow rate long the three zones of the installation and its pressure in the secondary circuit. All these have in view a proper solidification length; an intense cooling can generate cracks due to the thermal stress, while a too slow cooling can generate a partial solidification of the strand up to the cropping machine area. The paper presents a mathematical simulation of the continuously cast steel solidification.

El enfriamiento primario del cristalizador tiene una gran importancia sobre el espesor de la costra de acero solidificado. Si al salir del cristalizador, esta costra es demasiado sutil, bajo la acción de la presión ferro estática ejercitada por el acero líquido del interior y gracias el peso propio del hilo, ésta, puede perforar resultando su rompimiento. Los parámetros que influenyen sobre la cantidad de calor cedida dependen del agua de enfriamiento del catalizador, de la presión y de la temperatura de agua de enfriamiento, pero también del sobrecalentamiento del acero fundido continuamente. A la salida del

Solidification of Waste Steel Foudry Dust with Portland Cement

Czech Academy of Sciences Publication Activity Database

Škvára, F.; Kaštánek, František; Pavelková, I.; Šolcová, Olga; Maléterová, Ywetta; Schneider, Petr

B89, č. 1 (2001), s. 67-81 ISSN 0304-3894 R&D Projects: GA ČR GA104/99/0440 Institutional research plan: CEZ:AV0Z4072921; CEZ:MSM 223100002 Keywords : solidification, * foundry dust * cement Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 0.497, year: 2001

Modeling of Particle Engulfment during the Growth of Crystalline Silicon for Solar Cells

Science.gov (United States)

Tao, Yutao

A major challenge for the growth of multi-crystalline silicon is the formation of carbide and nitride precipitates in the melt that are engulfed by the solidification front to form inclusions. These lower cell efficiency and can lead to wafer breakage and sawing defects. Minimizing the number of these engulfed particles will promote lower cost and higher quality silicon and will advance progress in commercial solar cell production. To better understand the physical mechanisms responsible for such inclusions during crystal growth, we have developed finite-element, moving-boundary analyses to assess particle dynamics during engulfment via solidification fronts. Two-dimensional, steady-state and dynamic models are developed using the Galerkin finite element method and elliptic mesh generation techniques in an arbitrary Eulerian-Lagrangian (ALE) implementation. This numerical approach allows for an accurate representation of forces and dynamics previously inaccessible by approaches using analytical approximations. We reinterpret the significance of premelting via the definition of an unambiguous critical velocity for engulfment from steady-state analysis and bifurcation theory. Parametric studies are then performed to uncover the dependence of critical growth velocity upon some important physical properties. We also explore the complicated transient behaviors due to oscillating crystal growth conditions as well as the nonlinear nature related with temperature gradients and solute effects in the system. When compared with results for the SiC-Si system measured during ParSiWal experiments conducted by our collaborators, our model predicts a more realistic scaling of critical velocity with particle size than that predicted by prior theories. However, the engulfment growth velocity observed in the subsequent experiment onboard the TEXUS sounding rocket mission turned out to be unexpectedly higher. To explain this model discrepancy, a macroscopic model is developed in order

Directional solidification and characterization of the Al Nb2 - Al3 Nb eutectic system

International Nuclear Information System (INIS)

Trevisan, Eduardo A.O.; Andreotti, Fabio; Caram, Rubens

1996-01-01

The manufacturing of components to operate at high temperatures requires the use of metallic materials which can keep satisfactory mechanical and chemical properties, even at temperatures beyond 1000 deg C. An interesting alternative is the use of directionally solidified eutectic alloys. The eutectic alloy solidification makes possible the production of 'in situ' composite. A potentially useful system for manufacturing structural materials is the Al-Nb eutectic system. The aim of this work is to present the directional solidification of the Al-Nb eutectic alloy. (author)

Phase transformation and liquid density redistribution during solidification of Ni-based superalloy Inconel 718

Directory of Open Access Journals (Sweden)

Wang Ling

2012-08-01

Full Text Available The influences of chemical segregation and phase transformation on liquid density variation during solidification of Ni-based supperalloy Inconel 718 were investigated using SEM and EDS. It was found that significant segregation in liquid prompts high Nb phase to precipitate directly from liquid, which results in the redistribution of alloy elements and liquid density in their vicinity. The term “inter-precipitate liquid density” is therefore proposed and this concept should be applied to determine the solidification behavior of superalloy Inconel 718.

The density and velocity of plasma bullets propagating along one dielectric tube

Directory of Open Access Journals (Sweden)

Longfei Ji

2015-08-01

Full Text Available This study shows that the propagation of plasma bullets along one dielectric tube is strongly affected by many discharge parameters, such as the waveform of applied voltage (AC or pulsed DC, peak voltage, He flow rate, and the frequency of AC voltage. Analysis indicates that the density and velocity of plasma bullets are mainly determined by the electric field at the front of plasma bullets. These discharge parameters may significantly influence the distribution of plasma potential along the tube, thus control the electric field at the front of plasma bullets and their propagation. An increase in the pulsed DC voltage with its rise time of <40-50 ns can lead to an obvious improvement in the electric field at the front of plasma bullets, resulting in generation of a plasma in the high density gas and a fast propagation of plasma bullets. He flowing through the tube can contribute to the surface diffusion of charged species, and greatly increase the electric field at the front of plasma bullets. During the propagation of plasma bullets, their density is decreased due to the surface recombination of charged species, such as electrons and ions.

The solidification behavior of dilute aluminium-scandium alloys

International Nuclear Information System (INIS)

Norman, A.F.; Prangnell, P.B.; McEwen, R.S.

1998-01-01

The solidification behavior of dilute Sc containing Al alloys has been investigated. In binary Al-Sc alloys, Sc additions greater than the eutectic composition (0.55 wt%) were found to produce a remarkable refinement in the grain size of aluminum castings, of two orders of magnitude, due to the formation of the primary Al 3 Sc intermetallic phase during solidification. The refinement in grain size only occurred in hypereutectic compositions and was shown to be far greater than can be achieved by conventional Al grain refiners. Grain refinement by the addition of Sc is accompanied by a change in growth morphology from dendritic, in the large unrefined grains, to fine spherical grains with a divorced eutectic appearing on the grain boundaries in the refined castings. Similar levels of refinement were observed in Al-Sc-Zr and Al-Cu-Sc alloys. In the latter, a change in the segregation behavior of Cu was observed, from a strongly interdendritic segregation pattern to a more homogeneous distribution. The supersaturated Al-Sc solid solution can decompose via a discontinuous precipitation reaction to form coherent rod-like precipitates of the L1 2 Al 3 Sc phase

New insight on glass-forming ability and designing Cu-based bulk metallic glasses: The solidification range perspective

International Nuclear Information System (INIS)

Wu, Jili; Pan, Ye; Li, Xingzhou; Wang, Xianfei

2014-01-01

Highlights: • The equation, T rg = T g /T l , was rotationally modified to T rg = κ(T m /T l ) + C/T l . • The newly generalized equation suggests a way for describing glass-forming ability. • Several new Cu-based bulk metallic glasses were discovered by solidification range. - Abstract: In this paper, a new equation was rationally generalized from the reduced glass transition temperature. This equation indicates that solidification range can be used for describing glass-forming ability, which can be calculated with the aid of computational thermodynamic approach. Based on this scenario, several new Cu-based bulk metallic glasses in the ternary Cu–Zr–Ti alloy system were discovered. The as-cast samples were characterized by X-ray diffraction and transmission electronic microscopy. The results indicate that as-cast samples have monolithic amorphous nature. Thermal analysis validates that the smaller solidification range is closely related to the higher glass-forming ability, which is contributed to the effect of solidification time on the formation of bulk metallic glasses. This work also suggests that solidus can influence glass formation

The solidification of low level radioactive organic fluids with Envirostone Gypsum Cement

International Nuclear Information System (INIS)

Rosenstiel, T.L.; Lange, R.G.

1984-01-01

The primary method for the management of low level radioactive waste (LLW) has been and continues to be the isolation of the waste in a solid mass. Of the four typical LLW streams, organic fluids pose the most significant waste isolation problem. The organic fluids comprised of lubrication oils, hydraulic fluids, sludges, scintillation fluids, etc., result from the operation and maintenance of nuclear power generating stations, research activities, tooling operations, and diagnostic analyses. The United States Gypsum Company developed the patented Envirostone Gypsum Cement system for the solidification of all types of low level radioactive wastes to facilitate handling and transportation to regulated LLW disposal sites. For the solidification of organic fluids, Envirostone Gypsum Cement is used in conjunction with Envirostone Emulsifier, selected for its ability to emulsify a broad range of organic fluids in aqueous solutions. In the solidification process it is theorized that as the crystalline matrix of the gypsum forms, the micelles of the emulsifier behave as a chemical bridge which draws the organic fluid into the crystalline structure via the hydration water. Initial testing of physical properties of solidified waste forms, including leachability, per the requirements and the procedures specified for 10 CFR Part 61 as outlined in the Branch Technical Position Report from the United States Nuclear Regulatory Commission were in progress as of the writing of this paper. Upon completion of this testing a Topical Report will be submitted to the USNRC for review and approval. The presentation reviews field experience in the use of Envirostone Gypsum Cement for the solidification of low level radioactive organic fluids from nuclear power generating stations and makes an economic comparison between Envirostone Gypsum Cement and portland cement systems

X-Ray Radiographic Observation of Directional Solidification Under Microgravity: XRMON-GF Experiments on MASER12 Sounding Rocket Mission

Science.gov (United States)

Reinhart, G.; NguyenThi, H.; Bogno, A.; Billia, B.; Houltz, Y.; Loth, K.; Voss, D.; Verga, A.; dePascale, F.; Mathiesen, R. H.;

Microwave solidification development for Rocky Flats waste

Energy Technology Data Exchange (ETDEWEB)

Dixon, D.; Erle, R.; Eschen, V. [and others

1994-04-01

The Microwave Engineering Team at the Rocky Flats Plant has developed a production-scale system for the treatment of hazardous, radioactive, and mixed wastes using microwave energy. The system produces a vitreous final form which meets the acceptance criteria for shipment and disposal. The technology also has potential for application on various other waste streams from the public and private sectors. Technology transfer opportunities are being identified and pursued for commercialization of the microwave solidification technology.

Microwave solidification development for Rocky Flats waste

International Nuclear Information System (INIS)

Dixon, D.; Erle, R.; Eschen, V.

1994-04-01

The Microwave Engineering Team at the Rocky Flats Plant has developed a production-scale system for the treatment of hazardous, radioactive, and mixed wastes using microwave energy. The system produces a vitreous final form which meets the acceptance criteria for shipment and disposal. The technology also has potential for application on various other waste streams from the public and private sectors. Technology transfer opportunities are being identified and pursued for commercialization of the microwave solidification technology

Geochemistry of Natural Redox Fronts

International Nuclear Information System (INIS)

Hofmann, B.A.

1999-05-01

Redox fronts are important geochemical boundaries which need to be considered in safety assessment of deep repositories for radioactive waste. In most cases, selected host-rock formations will be reducing due to the presence of ferrous minerals, sulphides, etc. During construction and operation of the repository, air will be introduced into the formation. After repository closure, oxidising conditions may persist locally until all oxygen is consumed. In the case of high-level waste, radiolysis of water may provide an additional source of oxidants. Oxidising conditions within a repository are thus possible and potentially have a strong influence on the mobility of many elements. The rate of movement of redox fronts, the boundary between oxidising and reducing environments, and their influence on migrating radionuclides are thus important factors influencing repository performance. The present report is a review of elemental behaviour at natural redox fronts, based on published information and work of the author. Redox fronts are geochemically and geometrically variable manifestations of a global interface between generally oxidising geochemical milieux in contact with the atmosphere and generally reducing milieux in contact with rocks containing ferrous iron, sulphide and/or organic carbon. A classification of redox fronts based on a subdivision into continental near-surface, marine near-surface, and deep environments is proposed. The global redox interface is often located close to the surface of rocks and sediments and, sometimes, within bodies of water. Temperature conditions are close to ambient. A deeper penetration of the global redox front to depths of several kilometres is found in basins containing oxidised sediments (red beds) and in some hydrothermal circulation systems. Temperatures at such deep redox fronts may reach 200 o C. Both near-surface and deep redox fronts are sites of formation of economic deposits of redox-sensitive elements, particularly of

Wave fronts, pulses and wave trains in photoexcited superlattices behaving as excitable or oscillatory media

International Nuclear Information System (INIS)

Arana, J I; Bonilla, L L; Grahn, H T

2011-01-01

Undoped and strongly photoexcited semiconductor superlattices with field-dependent recombination behave as excitable or oscillatory media with spatially discrete nonlinear convection and diffusion. Infinitely long, dc-current-biased superlattices behaving as excitable media exhibit wave fronts with increasing or decreasing profiles, whose velocities can be calculated by means of asymptotic methods. These superlattices can also support pulses of the electric field. Pulses moving downstream with the flux of electrons can be constructed from their component wave fronts, whereas pulses advancing upstream do so slowly and experience saltatory motion: they change slowly in long intervals of time separated by fast transitions during which the pulses jump to the previous superlattice period. Photoexcited superlattices can also behave as oscillatory media and exhibit wave trains. (paper)

Theoretical analysis of the conical premixed flame response to upstream velocity disturbances considering flame speed development effects

Directory of Open Access Journals (Sweden)

Ghazaleh Esmaeelzade

2017-03-01

Full Text Available The effect of upstream velocity perturbations on the response of a premixed flame was investigated in terms of the flame transfer function dependency on excitation frequency. In this study, the assumption of constant flame speed was extended and the effect of flame speed development was considered; i.e., the flame speed would grow with the time after ignition or with the distance from a flame-holder. In the present study, the kinematics of a conical flame was investigated by linearization of the front tracking equation of flame to uniform and convected fluctuations of the flow velocity and the response was compared with that of a V-shaped flame and the experimental data in the previous studies. The results show that the effect of flame speed development could influence a decreasing gain and increase the phase of the flame response to the uniform velocity oscillations in low and moderate frequencies. Comparing the variations in the gain of flame response upon normalized frequency, show that a conical flame has lower values than the V-flame. In other words, these flames might be less susceptible to combustion instabilities than the V-flames. Furthermore, the variations in phase of the V-flames responses, which show a quasi-linear behavior with normalized frequency, have higher values than the saturated behavior in phase of the conical flame responses. Also, considering that the flame speed development induces an increase in the gain and phase of the conical flame response to the convected velocity oscillations in certain frequencies; because the developed flame front has longer length in comparison to the flame front in constant flame speed model. Therefore, the flame length may be longer than convective wavelength and the heat release would be generated in different points of the flame; consequently the flow oscillations might exert a stronger impact on the unsteady heat release fluctuations.

Onset of solid state mantle convection and mixing during magma ocean solidification

Science.gov (United States)

Maurice, Maxime; Tosi, Nicola; Samuel, Henri; Plesa, Ana-Catalina; Hüttig, Christian; Breuer, Doris

2017-04-01

The fractional crystallization of a magma ocean can cause the formation of a compositional layering that can play a fundamental role for the subsequent long-term dynamics of the interior, for the evolution of geochemical reservoirs, and for surface tectonics. In order to assess to what extent primordial compositional heterogeneities generated by magma ocean solidification can be preserved, we investigate the solidification of a whole-mantle Martian magma ocean, and in particular the conditions that allow solid state convection to start mixing the mantle before solidification is completed. To this end, we performed 2-D numerical simulations in a cylindrical geometry. We treat the liquid magma ocean in a parametrized way while we self-consistently solve the conservation equations of thermochemical convection in the growing solid cumulates accounting for pressure-, temperature- and, where it applies, melt-dependent viscosity as well as parametrized yield stress to account for plastic yielding. By testing the effects of different cooling rates and convective vigor, we show that for a lifetime of the liquid magma ocean of 1 Myr or longer, the onset of solid state convection prior to complete mantle crystallization is likely and that a significant part of the compositional heterogeneities generated by fractionation can be erased by efficient mantle mixing.

Experimental Study on Melting and Solidification of Phase Change Material Thermal Storage

Science.gov (United States)

Ambarita, H.; Abdullah, I.; Siregar, C. A.; Siregar, R. E. T.; Ronowikarto, A. D.

2017-03-01

Melting and solidification process of Phase Change Materials (PCMs) are investigated experimentally. The tested PCMs are Paraffin wax and Steric acid which typically used for solar water heater. The objective is to explore the characteristics of the PCM when it is being melted and solidified. The experiments are performed in a glass box. One side of the box wall is heated while the opposite wall is kept constant and other walls are insulated. Temperature of the heated wall are kept constant at 80°C, 85°C, and 90°C, respectively. Every experiment is carried out for 600 minutes. Temperatures are recorded and the melting and solidification processes are pictured by using camera. The results show that the melting process starts from the upper part of the thermal storage. In the solidification process, it starts from the lower part of the thermal storage. As a thermal energy storage, Paraffin wax is better than Steric acid. This is because Paraffin wax can store more energy. At heat source temperature of 90°C, thermal energy stored by Paraffin wax and Stearic acid is 61.84 kJ and 57.39 kJ, respectively. Thus it is better to used Paraffin wax in the solar water heater as thermal energy storage.

Two-dimensional time-resolved x-ray diffraction study of dual phase rapid solidification in steels

Science.gov (United States)

Yonemura, Mitsuharu; Osuki, Takahiro; Terasaki, Hidenori; Komizo, Yuichi; Sato, Masugu; Toyokawa, Hidenori; Nozaki, Akiko

2010-01-01

The high intensity heat source used for fusion welding creates steep thermal gradients of 100 °C/s from 1800 °C. Further, the influence of preferred orientation is important for the observation of a directional solidification that follows the dendrite growth along the ⟨100⟩ direction toward the moving heat source. In the present study, we observed the rapid solidification of weld metal at a time resolution of 0.01-0.1 s by a two-dimensional time-resolved x-ray diffraction (2DTRXRD) system for real welding. The diffraction rings were dynamically observed by 2DTRXRD with synchrotron energy of 18 keV while the arc passes over the irradiation area of the x-rays. The arc power output was 10 V-150 A, and the scan speed of the arc was 1.0 mm/s. The temperature rise in instruments was suppressed by a water-cooled copper plate under the specimen. Further, the temperature distribution of the weld metal was measured by a thermocouple and correlated with the diffraction patterns. Consequently, solidification and solid phase transformation of low carbon steels and stainless steels were observed during rapid cooling by 2DTRXRD. In the low carbon steel, the microstructure is formed in a two step process, (i) formation of crystallites and (ii) increase of crystallinity. In stainless steel, the irregular interface layer of δ/γ in the quenched metal after solidification is expected to show the easy movement of dendrites at a lower temperature. In carbide precipitation stainless steel, it is easy for NbC to grow on δ phase with a little undercooling. Further, a mistlike pattern, which differs from the halo pattern, in the fusion zone gave some indication of the possibilities to observe the nucleation and the early solidification by 2DTRXRD.

PHASE CHANGE AROUND A FINNED TUBE

Directory of Open Access Journals (Sweden)

Aytunç EREK

2003-01-01

Full Text Available This study presents the heat transfer enhancement in the thermal energy storage system by using radially finned tube. The solution of the system consists of the solving the equations of the heat transfer fluid (HTF, the pipe wall and fin, and the phase change material (PCM as one domain. The control volume finite difference approach and the semi implicit solver (SIS are used to solve the equations. Fully developed velocity distribution is taken in the HTF. Flow parameters (Re number and inlet temperature of coolant and fin parameters (the number of fins, fin length, fin thickness are found to influence solidification fronts and the total stored energy.

Process control of Low and Intermediate-level radioactive wastes solidification

International Nuclear Information System (INIS)

1993-01-01

Safety guidelines issued by the Spanish Council of Nuclear Safety (CSN) with basic criteria which must be adopted for the control of the Process for wastes solidification, establishing, in addition, a series of protocols and basic contents to assist the elaboration of Process Control Programs

Solidification of low-level radioactive wastes in masonry cement

International Nuclear Information System (INIS)

Zhou, H.; Colombo, P.

1987-03-01

Portland cements are widely used as solidification agents for low-level radioactive wastes. However, it is known that boric acid wastes, as generated at pressurized water reactors (PWR's) are difficult to solidify using ordinary portland cements. Waste containing as little as 5 wt % boric acid inhibits the curing of the cement. For this purpose, the suitability of masonry cement was investigated. Masonry cement, in the US consists of 50 wt % slaked lime (CaOH 2 ) and 50 wt % of portland type I cement. Addition of boric acid in molar concentrations equal to or less than the molar concentration of the alkali in the cement eliminates any inhibiting effects. Accordingly, 15 wt % boric acid can be satisfactorily incorporated into masonry cement. The suitability of masonry cement for the solidification of sodium sulfate wastes produced at boiling water reactors (BWR's) was also investigated. It was observed that although sodium sulfate - masonry cement waste forms containing as much as 40 wt % Na 2 SO 4 can be prepared, waste forms with more than 7 wt % sodium sulfate undergo catastrophic failure when exposed to an aqueous environment. It was determined by x-ray diffraction that in the presence of water, the sulfate reacts with hydrated calcium aluminate to form calcium aluminum sulfate hydrate (ettringite). This reaction involves a volume increase resulting in failure of the waste form. Formulation data were identified to maximize volumetric efficiency for the solidification of boric acid and sodium sulfate wastes. Measurement of some of the waste form properties relevant to evaluating the potential for the release of radionuclides to the environment included leachability, compression strengths and chemical interactions between the waste components and masonry cement. 15 refs., 19 figs., 9 tabs

Development of Stable Solidification Method for Insoluble Ferrocyanides-13170

Energy Technology Data Exchange (ETDEWEB)

Ikarashi, Yuki; Masud, Rana Syed; Mimura, Hitoshi [Dept. of Quantum Science and Energy Engineering, Graduate School of Engineering, Tohoku University, Aramaki-Aza-Aoba6-6-01-2, Sendai, 980-8579 (Japan); Ishizaki, Eiji; Matsukura, Minoru [UNION SHOWA K.K. 17-20, Mita 2-chome, Minato-ku, Tokyo 108-0073 (Japan)

2013-07-01

The development of stable solidification method of insoluble ferrocyanides sludge is an important subject for the safety decontamination in Fukushima NPP-1. By using the excellent immobilizing properties of zeolites such as gas trapping ability and self-sintering properties, the stable solidification of insoluble ferrocyanides was accomplished. The immobilization ratio of Cs for K{sub 2}[CoFe(CN){sub 6}].nH{sub 2}O saturated with Cs{sup +} ions (Cs{sub 2}[CoFe(CN){sub 6}].nH{sub 2}O) was estimated to be less than 0.1% above 1,000 deg. C; the adsorbed Cs{sup +} ions are completely volatilized. In contrast, the novel stable solid form was produced by the press-sintering of the mixture of Cs{sub 2}[CoFe(CN){sub 6}].nH{sub 2}O and zeolites at higher temperature of 1,000 deg. C and 1,100 deg. C; Cs volatilization and cyanide release were completely depressed. The immobilization ratio of Cs, under the mixing conditions of Cs{sub 2}[CoFe(CN){sub 6}].nH{sub 2}O:CP= 1:1 and calcining temperature: 1,000 deg. C, was estimated to be nearly 100%. As for the kinds of zeolites, natural mordenite (NM), clinoptilolite (CP) and Chabazite tended to have higher immobilization ratio compared to zeolite A. This may be due to the difference in the phase transformation between natural zeolites and synthetic zeolite A. In the case of the composites (K{sub 2-X}Ni{sub X/2}[NiFe(CN){sub 6}].nH{sub 2}O loaded natural mordenite), relatively high immobilization ratio of Cs was also obtained. This method using zeolite matrices can be applied to the stable solidification of the solid wastes of insoluble ferrocyanides sludge. (authors)

Front Propagation in Stochastic Neural Fields

KAUST Repository

Bressloff, Paul C.

2012-01-01

We analyze the effects of extrinsic multiplicative noise on front propagation in a scalar neural field with excitatory connections. Using a separation of time scales, we represent the fluctuating front in terms of a diffusive-like displacement (wandering) of the front from its uniformly translating position at long time scales, and fluctuations in the front profile around its instantaneous position at short time scales. One major result of our analysis is a comparison between freely propagating fronts and fronts locked to an externally moving stimulus. We show that the latter are much more robust to noise, since the stochastic wandering of the mean front profile is described by an Ornstein-Uhlenbeck process rather than a Wiener process, so that the variance in front position saturates in the long time limit rather than increasing linearly with time. Finally, we consider a stochastic neural field that supports a pulled front in the deterministic limit, and show that the wandering of such a front is now subdiffusive. © 2012 Society for Industrial and Applied Mathematics.

Solidification of saturated radioactive organic ion exchangers and of ash from incineration plant

International Nuclear Information System (INIS)

Timulak, J.; Krejci, F.; Pekar, A.; Gulis, G.; Breza, M.

1985-01-01

The study of bituminization of saturated radioactive organic ion exchangers was centred on finding the effect of the water content of ion exchangers on the process of solidification and on the water content of bituminization products, the optimization of temperature conditions in the process of bituminization, on seeking a suitable bitumen, on testing the radiation and thermal stability of the bituminization product, on finding its properties as well as the effects of nuclear radiation on these properties. Ion exchangers of Czechoslovak and Soviet make were used in all experiments. It was found that solidified ion exchangers must have a maximum moisture of 10%, and the temperature during solidification must not exceed 130 degC. The negative effect of boric acid on cement solidification may be removed by neutralization of esterification of this acid following its release from the ion exchangers by hydrochloric acid. Some other results of the experiments are tabulated. The obtained results describe the behaviour of the product only during a brief period of time as compared with the long time of long-term disposal. It will therefore be necessary to devote attention to finding the characteristics of long-term behaviour of products during disposal. (Z.M.)

Light-Front QCD

Energy Technology Data Exchange (ETDEWEB)

Brodsky, S.

2004-11-30

In these lectures, I survey a number of applications of light-front methods to hadron and nuclear physics phenomenology and dynamics, including light-front statistical physics. Light-front Fock-state wavefunctions provide a frame-independent representation of hadrons in terms of their fundamental quark and gluon degrees of freedom. Nonperturbative methods for computing LFWFs in QCD are discussed, including string/gauge duality which predicts the power-law fall-off at high momentum transfer of light-front Fock-state hadronic wavefunctions with an arbitrary number of constituents and orbital angular momentum. The AdS/CFT correspondence has important implications for hadron phenomenology in the conformal limit, including an all-orders derivation of counting rules for exclusive processes. One can also compute the hadronic spectrum of near-conformal QCD assuming a truncated AdS/CFT space. Given the LFWFs, one can compute form factors, heavy hadron decay amplitudes, hadron distribution amplitudes, and the generalized parton distributions underlying deeply virtual Compton scattering. The quantum fluctuations represented by the light-front Fock expansion leads to novel QCD phenomena such as color transparency, intrinsic heavy quark distributions, diffractive dissociation, and hidden-color components of nuclear wavefunctions. A new test of hidden color in deuteron photodisintegration is proposed. The origin of leading-twist phenomena such as the diffractive component of deep inelastic scattering, single-spin asymmetries, nuclear shadowing and antishadowing is also discussed; these phenomena cannot be described by light-front wavefunctions of the target computed in isolation. Part of the anomalous NuTeV results for the weak mixing angle {theta}{sub W} could be due to the non-universality of nuclear antishadowing for charged and neutral currents.

Cement radwaste solidification studies third annual report

International Nuclear Information System (INIS)

Brown, D.J.; James, J.M.; Lee, D.J.; Smith, D.L.; Walker, A.T.

1982-03-01

This report summarises cement radwaste studies carried out at AEE Winfrith during 1981 on the encapsulation of medium and low active waste in cement. During the year more emphasis has been placed on the work which is directly related to the solidification of SGHWR active sludge. Information has been obtained on the properties of 220 dm 3 drums of cemented waste. The use of cement grouts for the encapsulation of solid items has also been investigated during 1981. (U.K.)

Microstructure selection in thin-sample directional solidification of an Al-Cu alloy: In situ X-ray imaging and phase-field simulations

International Nuclear Information System (INIS)

Clarke, A. J.; Tourret, D.; Song, Y.; Imhoff, S. D.; Gibbs, P. J.

2017-01-01

We study microstructure selection during during directional solidification of a thin metallic sample. We combine in situ X-ray radiography of a dilute Al-Cu alloy solidification experiments with three-dimensional phase-field simulations. Here we explore a range of temperature gradient G and growth velocity V and build a microstructure selection map for this alloy. We investigate the selection of the primary dendritic spacing Λ and tip radius ρ. While ρ shows a good agreement between experimental measurements and dendrite growth theory, with ρ~V"-"1"/"2, Λ is observed to increase with V (∂Λ/∂V > 0), in apparent disagreement with classical scaling laws for primary dendritic spacing, which predict that ∂Λ/∂V<0. We show through simulations that this trend inversion for Λ(V) is due to liquid convection in our experiments, despite the thin sample configuration. We use a classical diffusion boundary-layer approximation to semi-quantitatively incorporate the effect of liquid convection into phase-field simulations. This approximation is implemented by assuming complete solute mixing outside a purely diffusive zone of constant thickness that surrounds the solid-liquid interface. This simple method enables us to quantitatively match experimental measurements of the planar morphological instability threshold and primary spacings over an order of magnitude in V. Lastly, we explain the observed inversion of ∂Λ/∂V by a combination of slow transient dynamics of microstructural homogenization and the influence of the sample thickness.

PELVIC ROTATION AND LOWER EXTREMITY MOTION WITH TWO DIFFERENT FRONT FOOT DIRECTIONS IN THE TENNIS BACKHAND GROUNDSTROKE

Directory of Open Access Journals (Sweden)

Sayumi Iwamoto

2013-06-01

Full Text Available When a tennis player steps forward to hit a backhand groundstroke in closed stance, modifying the direction of the front foot relative to the net may reduce the risk of ankle injury and increase performance. This study evaluated the relationship between pelvic rotation and lower extremity movement during the backhand groundstroke when players stepped with toes parallel to the net (Level or with toes pointed towards the net (Net. High school competitive tennis players (eleven males and seven females, 16.8 ± 0.8 years, all right- handed performed tennis court tests comprising five maximum speed directional runs to the court intersection line to hit an imaginary ball with forehand or backhand swings. The final backhand groundstroke for each player at the backcourt baseline was analyzed. Pelvic rotation and lower extremity motion were quantified using 3D video analysis from frontal and sagittal plane camera views reconstructed to 3D using DLT methods. Plantar flexion of ankle and supination of the front foot were displayed for both Net and Level groups during the late phase of the front foot step. The timings of the peak pelvis rotational velocity and peak pelvis rotational acceleration showed different pattern for Net and Level groups. The peak timing of the pelvis rotational velocity of the Level group occurred during the late phase of the step, suggesting an increase in the risk of inversion ankle sprain and a decrease in stroke power compared to the Net group

Modelling of melting and solidification transport phenomena during hypothetical NPP severe accidents

Energy Technology Data Exchange (ETDEWEB)

Sarler, B [Inst. Jozef Stefan, Ljubljana (Slovenia)

1992-07-01

A physical and mathematical framework to deal with the transport phenomena occuring during melting and solidification of the hypothetical NPP severe accidents is presented. It concentrates on the transient temperature, velocity, and species concentration distributions during such events. The framework is based on the Mixture Continuum Formulation of the components and phases, cast in the boundary-domain integral shape structured by the fundamental solution of the Laplace equation. The formulation could cope with various solid-liquid sub-systems through the inclusion of the specific closure relations. The deduced system of boundary-domain integral equations for conservation of mass, energy, momentum, and species could be solved by the boundary element discrete approximative method. (author) [Slovenian] Predstavljeno je fizikalno in matematicno ogrodje za obravnavo prenosnih pojavov taljenja in strjevanja med hipoteticnimi tezkimi nezgodami v jedrskih elektrarnah. Osredotoceno je na popis neustaljene porazdelitve temperatur, hitrosti in koncentracij sestavin med taksnimi dogodki. Ogrodje temelji na formulaciji kontinuuma mesanice komponent in faz, v obliki robno obmocnih integralskih enacb, ki so sestavljena na podlagi fundamentalne resitve Laplace-ove enacbe. Formulacija lahko popisuje stevilne trdno-tekoce pod-sisteme na podlagi specificnih sklopitvenih relacij. Izpeljan sistem robno-obmocnih integralskih enacb za popis ohranitve mase, energije, gibalne kolicine in sestavin lahko resimo na podlagi diskretne aproksimativne metode robnih elementov. (author)

Numerical Model for Solidification Zones Selection in the Large Ingots

Directory of Open Access Journals (Sweden)

Wołczyński W.

2015-12-01

Full Text Available A vertical cut at the mid-depth of the 15-ton forging steel ingot has been performed by curtesy of the CELSA - Huta Ostrowiec plant. Some metallographic studies were able to reveal not only the chilled undersized grains under the ingot surface but columnar grains and large equiaxed grains as well. Additionally, the structural zone within which the competition between columnar and equiaxed structure formation was confirmed by metallography study, was also revealed. Therefore, it seemed justified to reproduce some of the observed structural zones by means of numerical calculation of the temperature field. The formation of the chilled grains zone is the result of unconstrained rapid solidification and was not subject of simulation. Contrary to the equiaxed structure formation, the columnar structure or columnar branched structure formation occurs under steep thermal gradient. Thus, the performed simulation is able to separate both discussed structural zones and indicate their localization along the ingot radius as well as their appearance in term of solidification time.

A phase-field model for non-equilibrium solidification of intermetallics

International Nuclear Information System (INIS)

Assadi, H.

2007-01-01

Intermetallics may exhibit unique solidification behaviour-including slow growth kinetics, anomalous partitioning and formation of unusual growth morphologies-because of departure from local equilibrium. A phase-field model is developed and used to illustrate these non-equilibrium effects in solidification of a prototype B2 intermetallic phase. The model takes sublattice compositions as primary field variables, from which chemical long-range order is derived. The diffusive reactions between the two sublattices, and those between each sublattice and the liquid phase are taken as 'internal' kinetic processes, which take place within control volumes of the system. The model can thus capture solute and disorder trapping effects, which are consistent-over a wide range of the solid/liquid interface thickness-with the predictions of the sharp-interface theory of solute and disorder trapping. The present model can also take account of solid-state ordering and thus illustrate the effects of chemical ordering on microstructure formation and crystal growth kinetics

Solidification of Bi2Sr2Ca1Cu2Oy and Bi2Sr1.75Ca0.25CuOy

International Nuclear Information System (INIS)

Holesinger, T.G.; Miller, D.J.; Viswanathan, H.K.; Chumbley, L.S.

1993-01-01

The solidification processes for the compositions Bi 2 Sr 2 CaCu 2 O y (2212) and Bi 2 Sr 1.75 Ca 0.25 CuO y (2201) were determined as a function of oxygen partial pressure. During solidification in argon, the superconducting phases were generally not observed to form for either composition. In both cases, the solidus is lowered to approximately 750 degree C. Solidification of Bi 2 Sr 1.75 Ca 0.25 CuO y in Ar resulted in a divorced eutectic structure of Bi 2 Sr 2-x Ca x O y (22x) and Cu 2 O while solidification of Bi 2 Sr 2 CaCu 2 O y in Ar resulted in a divorced eutectic structure of Bi 2 Sr 3-x Ca x O y (23x) and Cu 2 O. Solidification of Bi 2 Sr 1.75 Ca 0.25 CuO y in O 2 resulted in large grains of 2201 interspersed with small regions containing the eutectic structure of 22x and CuO/Cu 2 O. Solidification of Bi 2 Sr 2 CaCu 2 O y in partial pressures of 1%, 20%, and 100% oxygen resulted in multiphase samples consisting of 2212, 2201, some alkaline-earth cuprates, and both divorced eutectic structures found during solidification in Ar. For both compositions, these latter structures can be attributed to oxygen deficiencies present in the melt regardless of the overpressure of oxygen. These eutectic structures are unstable and convert into the superconducting phases during subsequent anneals in oxygen. The formation process of the 2212 phase during solidification from the melt was determined to proceed through an intermediate state involving the 2201 phase

NOCHAR Polymers: An Aqueous and Organic Liquid Solidification Process for Cadarache LOR (Liquides Organiques Radioactifs) - 13195

International Nuclear Information System (INIS)

Vaudey, Claire-Emilie; Renou, Sebastien; Porco, Julien; Kelley, Dennis; Cochaud, Chantal; Serrano, Roger

2013-01-01

To handle the Very Low Level Waste (VLLW) and the Low Level Waste (LLW) in France, two options can be considered: the incineration at CENTRACO facility and the disposal facility on ANDRA sites. The waste acceptance in these radwaste routes is dependent upon the adequacy between the waste characteristics (physical chemistry and radiological) and the radwaste route specifications. If the waste characteristics are incompatible with the radwaste route specifications (presence of significant quantities of chlorine, fluorine, organic component etc or/and high activity limits), it is necessary to find an alternative solution that consists of a waste pre-treatment process. In the context of the problematic Cadarache LOR (Liquides Organiques Radioactifs) waste streams, two radioactive scintillation cocktails have to be treated. The first one is composed of organic liquids at 13.1 % (diphenyloxazol, mesitylene, TBP, xylene) and water at 86.9 %. The second one is composed of TBP at 8.6 % and water at 91.4 %. They contain chlorine, fluorine and sulphate and have got alpha/beta/gamma spectra with mass activities equal to some kBq.g -1 . Therefore, tritium is present and creates the second problematic waste stream. As a consequence, in order for disposal acceptance at the ANDRA site, it is necessary to pre-treat the waste. The NOCHAR polymers as an aqueous and organic liquid solidification process seem to be an adequate solution. Indeed, these polymers constitute an important variety of products applied to the treatment of radioactive aqueous and organic liquids (solvent, oil, solvent/oil mixing etc) and sludge through a mechanical and chemical solidification process. For Cadarache LOR, N910 and N960 respectively dedicated to the organic and aqueous liquids solidification are considered. With the N910, the organic waste solidification occurs in two steps. As the organic liquid travels moves through the polymer strands, the strands swell and immobilise the liquid. Then as the

Direct observation of spatially isothermal equiaxed solidification of an Al-Cu alloy in microgravity on board the MASER 13 sounding rocket

Science.gov (United States)

Murphy, A. G.; Mathiesen, R. H.; Houltz, Y.; Li, J.; Lockowandt, C.; Henriksson, K.; Melville, N.; Browne, D. J.

2016-11-01

For the first time, isothermal equiaxed solidification of a metallic alloy has been observed in situ in space, providing unique benchmark experimental data. The experiment was completed on board the MASER 13 sounding rocket, launched in December 2015, using a newly developed isothermal solidification furnace. A grain-refined Al-20 wt%Cu sample was fully melted and solidified during 360 s of microgravity and the solidification sequence was recorded using time-resolved X-radiography. Equiaxed nucleation, dendritic growth, solutal impingement, and eutectic transformation were thus observed in a gravity-free environment. Equiaxed nucleation was promoted through application of a controlled cooling rate of -0.05 K/s producing a 1D grain density of 6.5 mm-1, uniformly distributed throughout the field of view (FOV). Primary growth slowed to a visually imperceptible level at an estimated undercooling of 7 K, after which the cooling rate was increased to -1.0 K/s for the remainder of solidification and eutectic transformation, ensuring the sample was fully solidified inside the microgravity time window. The eutectic transformation commenced at the centre of the FOV proceeding radially outwards covering the entire FOV in 3 s Microgravity-based solidification is compared to an identical pre-flight ground-based experiment using the same sample and experiment timeline. The ground experiment was designed to minimise gravity effects, by choice of a horizontal orientation for the sample, so that any differences would be subtle. The first equiaxed nucleation occurred at an apparent undercooling of 0.6 K less than the equivalent event during microgravity. During primary equiaxed solidification, as expected, no buoyant grain motion was observed during microgravity, compared to modest grain rotation and reorientation observed during terrestrial-based solidification. However, when the cooling rate was increased from -0.05 K/s to -1.0 K/s during the latter stages of solidification, in

Solidification treatment of thiophene and BTEX contaminated soils

International Nuclear Information System (INIS)

Zarlinski, S.J.; Kingham, N.W.; Blevins, J.

1995-01-01

Contamination at the McColl Superfund Site, located in Fullerton, California, is due to the disposal, in pits, of spent sulfuric acid sludge from the production of aviation fuel. A treatability study was performed to evaluate the electiveness of in situ solidification treatment of materials contaminated with high concentrations of benzene, toluene, ethylbenzene, and xylenes (BTEX), as well as thiophene and other organic compounds. The contaminated materials were extremely acidic (pH<1) and had high organic and sulfur contents of greater than 70 percent and 10 percent, respectively. A total of 150 mixtures were screened to evaluate the effectiveness of 15 reagents. Based on the preliminary screening results, six mixtures were selected as being the most effective at treating the contaminated materials. Comprehensive evaluations of the candidate mixtures included (1) quantitative glovebag volatilization studies, (2) chemical characterization of the treated materials, (3) strength characterizations at multiple cure times of up to 60 days, (4) emissions monitoring of the treated materials at cure times of 7 and 14 days, and (5) the evaluation of oxidation reagents for treatment of the thiophene contamination. The treatability study demonstrated that solidification treatment is an effective alternative for remediation of the thiophene and BTEX contaminated materials

Wax solidification of drying agents containing tritiated water

International Nuclear Information System (INIS)

Mishikawa, M.; Kido, H.

1984-01-01

It is necessary to immobilize the tritium not to give any impact on the environmental biosphere because tritium may give profound effects in the metabolic pathway. One of the most probable methods of immobilizing tritium would be incorporation of tritiated water in solid forms. Any drying or dehydration technique would be effective in a tritium cleanup system for off-gas streams containing tritium or tritiated water. Commonly used drying agents such as activated alumina, silica gel, molecular sieves and calcium sulfate are of value for removal of water vapour from air or other gases. For long term tritium storage, however, these adsorptive materials should be enveloped to prevent contact with water or water vapour because the rate of leaching, evaporation or diffusion of tritium from these porous materials is so large. The beeswax solidification method of the packed bed of drying agents adsorbing tritiated water is developed in this study, where the wax solidification procedure is performed by pouring the melt of wax into the void space of the packed bed of the drying agents and successive gradual cooling. The observed values of diffusivity or permeability of tritium in the wax solidified materials are about one-thousandth of those obtained for the cement block. Effect of coating on the rate of leaching is also discussed

Crystallographic investigation of grain selection during initial solidification

International Nuclear Information System (INIS)

Esaka, H; Shinozuka, K; Kataoka, Y

2016-01-01

Normally, macroscopic solidified structure consists of chill, columnar and equiaxed zones. In a chill zone, many fine grains nucleate on the mold surface and grow their own preferred growth direction. Only a few of them continue to grow because of grain selection. In order to understand the grain selection process, crystallographic investigation has been carried out in the zone of initial solidification in this study. 10 g of Al-6 wt%Si alloy was melted at 850 °C and poured on the thick copper plate. Longitudinal cross section of the solidified shell was observed by a SEM and analyzed by EBSD. The result of EBSD mapping reveals that crystallographic orientation was random in the range of initial solidification. Further, some grains are elongated along their <100> direction. Columnar grains, whose growth directions are almost parallel to the heat flow direction, develop via grain selection. Here, a dendrite whose growth direction is close to the heat flow direction overgrows the other dendrite whose growth direction is far from the heat flow direction. However, sometimes we observed that dendrite, whose zenith angle is large, overgrew the other dendrite. It can be deduced that the time of nucleation on the mold surface is not constant. (paper)

Divorced Eutectic Solidification of Mg-Al Alloys

Science.gov (United States)

Monas, Alexander; Shchyglo, Oleg; Kim, Se-Jong; Yim, Chang Dong; Höche, Daniel; Steinbach, Ingo

2015-08-01

We present simulations of the nucleation and equiaxed dendritic growth of the primary hexagonal close-packed -Mg phase followed by the nucleation of the -phase in interdendritic regions. A zoomed-in region of a melt channel under eutectic conditions is investigated and compared with experiments. The presented simulations allow prediction of the final properties of an alloy based on process parameters. The obtained results give insight into the solidification processes governing the microstructure formation of Mg-Al alloys, allowing their targeted design for different applications.

Densities of Pb-Sn alloys during solidification

Science.gov (United States)

Poirier, D. R.

1988-01-01

Data for the densities and expansion coefficients of solid and liquid alloys of the Pb-Sn system are consolidated in this paper. More importantly, the data are analyzed with the purpose of expressing either the density of the solid or of the liquid as a function of its composition and temperature. In particular, the densities of the solid and of the liquid during dendritic solidification are derived. Finally, the solutal and thermal coefficients of volume expansion for the liquid are given as functions of temperature and composition.

Solute trapping of Ge in Al

International Nuclear Information System (INIS)

Smith, P.M.; West, J.A.; Aziz, M.J.

1992-01-01

This paper reports on partitioning during rapid solidification of dilute Al-Ge alloys. Implanted thin films of Al have been pulsed-laser melted to obtain solidification at velocities in the range of 0.01 ms to 3.3 m/s, as measured by the transient conductance technique. Previous and subsequent Rutherford Backscattering depth profiling of the Ge solute in the Al alloys has been used to determine the nonequilibrium partition coefficient k. A significant degree of lateral film growth during solidification confines determination of k to the placing of an upper bound of 0.22 on k for solidification velocities in this range. The authors place a lower limit of 10 m/s on the diffusive velocity, which locates the transition from solute partitioning to solute trapping in the Continuous Growth Model

Investigation on the formation of the preferred orientations in a TbDyFe alloy with directional solidification

International Nuclear Information System (INIS)

Jiang Chengbao; Xu Huibin

1999-01-01

The formation of the preferred orientations in a TbDyFe alloy was studied by transmission electron microscopy (TEM). It was found that there were several different preferred orientations in the experimental TbDyFe alloy with directional solidification. left angle 110 right angle, left angle 112 right angle and left angle 113 right angle preferred orientations were observed in this alloy solidified by our self-made super high gradient temperature directional solidification device. The preferred orientations changed with the variation of the solidification conditions. Two {111} twinning systems resulted in the left angle 110 right angle preferred orientation and a single {111} twinning system resulted in the left angle 112 right angle preferred orientation. The twinning displacement was observed and this formatted the left angle 113 right angle preferred orientation. (orig.)

Solidification of eutectic system alloys in space (M-19)

Science.gov (United States)

Ohno, Atsumi

1993-01-01

It is well known that in the liquid state eutectic alloys are theoretically homogeneous under 1 g conditions. However, the homogeneous solidified structure of this alloy is not obtained because thermal convection and non-equilibrium solidification occur. The present investigators have clarified the solidification mechanisms of the eutectic system alloys under 1 g conditions by using the in situ observation method; in particular, the primary crystals of the eutectic system alloys never nucleated in the liquid, but instead did so on the mold wall, and the crystals separated from the mold wall by fluid motion caused by thermal convection. They also found that the equiaxed eutectic grains (eutectic cells) are formed on the primary crystals. In this case, the leading phase of the eutectic must agree with the phase of the primary crystals. In space, no thermal convection occurs so that primary crystals should not move from the mold wall and should not appear inside the solidified structure. Therefore no equiaxed eutectic grains will be formed under microgravity conditions. Past space experiments concerning eutectic alloys were classified into two types of experiments: one with respect to the solidification mechanisms of the eutectic alloys and the other to the unidirectional solidification of this alloy. The former type of experiment has the problem that the solidified structures between microgravity and 1 g conditions show little difference. This is why the flight samples were prepared by the ordinary cast techniques on Earth. Therefore it is impossible to ascertain whether or not the nucleation and growth of primary crystals in the melt occur and if primary crystals influence the formation of the equiaxed eutectic grains. In this experiment, hypo- and hyper-eutectic aluminum copper alloys which are near eutectic point are used. The chemical compositions of the samples are Al-32.4mass%Cu (Hypo-eutectic) and Al-33.5mass%Cu (hyper-eutectic). Long rods for the samples are

An Advantage of the Equivalent Velocity Spectroscopy for Femtsecond Pulse Radiolysis

CERN Document Server

Kondoh, Takafumi; Tagawa, Seiichi; Tomosada, Hiroshi; Yang Jin Feng; Yoshida, Yoichi

2005-01-01

For studies of electron beam induced ultra-fast reaction process, femtosecond(fs) pulse radiolysis is under construction. To realize fs time resolution, fs electron and analyzing light pulses and their jitter compensation system are needed. About a 100fs electron pulse was generated by a photocathode RF gun linac and a magnetic pulse compressor. Synchronized Ti: Sapphire laser have a puleswidth about 160fs. And, it is significant to avoid degradation of time resolution caused by velocity difference between electron and analyzing light in a sample. In the 'Equivalent velocity spectroscopy' method, incident analyzing light is slant toward electron beam with an angle associated with refractive index of sample. Then, to overlap light wave front and electron pulse shape, electron pulse shape is slanted toward the direction of travel. As a result of the equivalent velocity spectroscopy for hydrated electrons, using slanted electron pulse shape, optical absorption rise time was about 1.4ps faster than normal electro...

Crustal evolution derived from the Izu-Bonin-Mariana arc velocity images

Science.gov (United States)

Takahashi, N.; Kodaira, S.; Tatsumi, Y.; Miura, S.; Sato, T.; Yamashita, M.; No, T.; Takahashi, T.; Noguchi, N.; Takizawa, K.; Kaiho, Y.; Kaneda, Y.

2010-12-01

The Izu-Bonin-Mariana arc is known as one of typical oceanic island arcs, which has developed by subduction between oceanic crusts producing continental materials. Japan Agency for Marine-Earth Science and Technology has carried out seismic surveys using a multi-channel reflection survey system (MCS) and ocean bottom seismographs (OBSs) in the Izu-Bonin-Mariana (IBM) arc since 2002, and reported these crustal images. As the results, we identified the structural characteristics of whole Izu-Bonin-Mariana arc. Rough structural characteristics are, 1) middle crust with Vp of 6 km/s, 2) upper part of the lower crust with Vp of 6.5-6.8 km/s, 3) lower part of the lower crust with Vp of 6.8-7.5 km/s, and 4) lower mantle velocity beneath the arc crusts. In addition, structural variation along the volcanic front, for example, thickness variation of andesitic layers was imaged and the distributions is consistent with those of rhyolite volcanoes, that is, it suggested that the cause the structural variation is various degree of crustal growth (Kodaira et al., 2007). Moreover, crustal thinning with high velocity lower crust across arc was also imaged, and it is interpreted that such crust has been influenced backarc opening (Takahashi et al., 2009). According to Tatsumi et al. (2008), andesitic middle crust is produced by differentiation of basaltic lower crust and a part of the restites are transformed to the upper mantle. This means that region showing much crustal differentiation has large volume of transformation of dense crustal materials to the mantle. We calculated volume profiles of the lower crust along all seismic lines based on the petrologic model, and compared them with observed real volumes obtained by seismic images. If the real volume of the lower crust is large, it means that the underplating of dense materials to the crustal bottom is dominant rather than transformation of dense materials to the upper mantle. According to obtained profiles to judge if the

Active learning of Pareto fronts.

Science.gov (United States)

Campigotto, Paolo; Passerini, Andrea; Battiti, Roberto

2014-03-01

This paper introduces the active learning of Pareto fronts (ALP) algorithm, a novel approach to recover the Pareto front of a multiobjective optimization problem. ALP casts the identification of the Pareto front into a supervised machine learning task. This approach enables an analytical model of the Pareto front to be built. The computational effort in generating the supervised information is reduced by an active learning strategy. In particular, the model is learned from a set of informative training objective vectors. The training objective vectors are approximated Pareto-optimal vectors obtained by solving different scalarized problem instances. The experimental results show that ALP achieves an accurate Pareto front approximation with a lower computational effort than state-of-the-art estimation of distribution algorithms and widely known genetic techniques.

Systematic front distortion and presence of consecutive fronts in a precipitation system

NARCIS (Netherlands)

Volford, A.; Izsak, F.; Ripszam, M.; Lagzi, I.

2006-01-01

A new simple reaction-diffusion system is presented focusing on pattern formation phenomena as consecutive precipitation fronts and distortion of the precipitation front.The chemical system investigated here is based on the amphoteric property of aluminum hydroxide and exhibits two unique phenomena.

The sequence of intermetallic formation and solidification pathway of an Al–13Mg–7Si–2Cu in-situ composite