Neutron emission from impacted solid LiD samples

International Nuclear Information System (INIS)

Kaushik, T.C.; Shyam, A.; Kulkarni, L.V.; Srinivasan, M.

1993-01-01

Nylon projectiles with 0.1 g to 0.3 g mass, accelerated to velocities of 0.2-1 km/s using a 60 cm long electromagnetic accelerator (railgun), have been impacted upon solid lithium deuteride (LiD) samples of 3 proportional counters. The output from the BF 3 set-up is monitored in several ways to characterize the possible neutron emission from the target. This includes a simple technique of counting the single channel analyser (SCA) output through a dead-time unit to identify bursts of < 100 μs duration. Counting is started after a delay of ∼ 1 ms to avoid the initial interference from the capacitor bank discharge. The signal is also recorded in a storage oscilloscope from the start of projectile acceleration along with a time marker just before the impact. From a number of shots taken with and without the samples, a significant evidence of neutron emission from the LiD samples appears to emerge. The experiments suggest that approximately 100 neutrons might be generated during every such impact in a duration of < 4 ms. (author). 7 refs., 3 figs

Electron emission from solids induced by swift heavy ions

International Nuclear Information System (INIS)

Xiao Guoqing

2000-01-01

The recent progresses in experimental and theoretical studies of the collision between swift heavy ion and solids as well as electron emission induced by swift heavy ion in solids were briefly reviewed. Three models, Coulomb explosion, thermal spike and repulsive long-lived states, for interpreting the atomic displacements stimulated by the electronic energy loss were discussed. The experimental setup and methods for measuring the electron emission from solids were described. The signification deviation from a proportionality between total electron emission yields and electronic stopping power was found. Auger-electron and convoy-electron spectra are thought to be a probe for investigating the microscopic production mechanisms of the electronic irradiation-damage. Electron temperature and track potential at the center of nuclear tracks in C and polypropylene foils induced by 5 MeV/u heavy ions, which are related to the electronic excitation density in metals and insulators respectively, were extracted by measuring the high resolution electron spectra

Preliminary investigation of solid target geometry

Energy Technology Data Exchange (ETDEWEB)

Haga, Katsuhiro; Kaminaga, Masanori; Hino, Ryutaro; Takada, Hiroshi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Shafiqul, I.M.; Tsuji, Nobumasa; Okamoto, Hutoshi; Kumasaka, Katsuyuki; Hayashi, Katsumi

1997-11-01

In this report, we introduce the developing plan for a solid metal target structure. Supposing tantalum as the target material, the temperature distribution and the maximum thermal stress in a tantalum plate of a solid metal target was evaluated under a water cooling condition, using the heat generation rate calculated with the JAERI`s neutron transport code. The calculation results showed that the water velocity was higher than 10 m/s in order to cool the 3mm-thick target plate down to 200degC when the target surface was smooth and heat transfer rate was calculated with the Dittus-Boelter equation. In this case, the maximum thermal stress is 50 MPa at the target plate surface. The coolant water flow distribution in a target vessel was also evaluated for ISIS-type flow channels and the parallel flow channels. In the ISIS-type flow channels, at least 25mm height of the coolant plenum is needed for a uniform flow distribution. The maximum flow velocity difference between the flow gaps in the parallel flow channels was 30%. A heat transfer augmentation experiment was conducted using ribbed-surface flow channel. The heat transfer rate was confirmed to increase up to twice the value of that for a smooth surface. (author)

Gaseous emissions from management of solid waste: a systematic review.

Science.gov (United States)

Pardo, Guillermo; Moral, Raúl; Aguilera, Eduardo; Del Prado, Agustín

2015-03-01

The establishment of sustainable soil waste management practices implies minimizing their environmental losses associated with climate change (greenhouse gases: GHGs) and ecosystems acidification (ammonia: NH3 ). Although a number of management strategies for solid waste management have been investigated to quantify nitrogen (N) and carbon (C) losses in relation to varied environmental and operational conditions, their overall effect is still uncertain. In this context, we have analyzed the current scientific information through a systematic review. We quantified the response of GHG emissions, NH3 emissions, and total N losses to different solid waste management strategies (conventional solid storage, turned composting, forced aerated composting, covering, compaction, addition/substitution of bulking agents and the use of additives). Our study is based on a meta-analysis of 50 research articles involving 304 observations. Our results indicated that improving the structure of the pile (waste or manure heap) via addition or substitution of certain bulking agents significantly reduced nitrous oxide (N2 O) and methane (CH4 ) emissions by 53% and 71%, respectively. Turned composting systems, unlike forced aerated composted systems, showed potential for reducing GHGs (N2 O: 50% and CH4 : 71%). Bulking agents and both composting systems involved a certain degree of pollution swapping as they significantly promoted NH3 emissions by 35%, 54%, and 121% for bulking agents, turned and forced aerated composting, respectively. Strategies based on the restriction of O2 supply, such as covering or compaction, did not show significant effects on reducing GHGs but substantially decreased NH3 emissions by 61% and 54% for covering and compaction, respectively. The use of specific additives significantly reduced NH3 losses by 69%. Our meta-analysis suggested that there is enough evidence to refine future Intergovernmental Panel on Climate Change (IPCC) methodologies from solid waste

Gaseous emissions from management of solid waste: a systematic review

Science.gov (United States)

Pardo, Guillermo; Moral, Raúl; Aguilera, Eduardo; del Prado, Agustín

2015-01-01

The establishment of sustainable soil waste management practices implies minimizing their environmental losses associated with climate change (greenhouse gases: GHGs) and ecosystems acidification (ammonia: NH3). Although a number of management strategies for solid waste management have been investigated to quantify nitrogen (N) and carbon (C) losses in relation to varied environmental and operational conditions, their overall effect is still uncertain. In this context, we have analyzed the current scientific information through a systematic review. We quantified the response of GHG emissions, NH3 emissions, and total N losses to different solid waste management strategies (conventional solid storage, turned composting, forced aerated composting, covering, compaction, addition/substitution of bulking agents and the use of additives). Our study is based on a meta-analysis of 50 research articles involving 304 observations. Our results indicated that improving the structure of the pile (waste or manure heap) via addition or substitution of certain bulking agents significantly reduced nitrous oxide (N2O) and methane (CH4) emissions by 53% and 71%, respectively. Turned composting systems, unlike forced aerated composted systems, showed potential for reducing GHGs (N2O: 50% and CH4: 71%). Bulking agents and both composting systems involved a certain degree of pollution swapping as they significantly promoted NH3 emissions by 35%, 54%, and 121% for bulking agents, turned and forced aerated composting, respectively. Strategies based on the restriction of O2 supply, such as covering or compaction, did not show significant effects on reducing GHGs but substantially decreased NH3 emissions by 61% and 54% for covering and compaction, respectively. The use of specific additives significantly reduced NH3 losses by 69%. Our meta-analysis suggested that there is enough evidence to refine future Intergovernmental Panel on Climate Change (IPCC) methodologies from solid waste

Non-ETS emission targets for 2030. Indication of emission targets for the Netherlands and other EU Member States under the European Effort Sharing Decision

Energy Technology Data Exchange (ETDEWEB)

Verdonk, M.; Hof, A.

2013-10-15

As European Member States are making progress towards their 2020 targets in the Effort Sharing Decision, the attention of policymakers is shifting to a framework beyond 2020. The European Commission launched a discussion with its Green Paper on a possible policy framework for 2030. This PBL Note aims to contribute to that discussion by analysing the effects of various assumptions on Member States' non-ETS emission targets for 2030. The effort sharing of the current European target for 2020 has resulted in an emission target of +20% relative to 2005 levels for the least wealthy Member State and -20% for the three wealthiest Member States. The targets for all other Member States were determined based on per-capita income levels of 2005. For possible non-ETS targets for 2030, we assumed a Europe-wide emission reduction target of 40% for 2030, compared to 1990 levels. This target is considered by the European Commission as the most cost-efficient to achieve a low-carbon economy by 2050. The 2030 target was split into a target for emissions covered by the EU Emissions Trading System (ETS) and one for emissions that are not covered by the ETS (non-ETS). According to our estimations, European non-ETS emissions need to be reduced by around 30% by 2030, compared to 2005 levels. We distributed the non-ETS reduction target of 30% over the Member States by using similar effort sharing principles that are applied in the EU Effort Sharing Decision for 2020, but with different targets assumed for the least wealthy Member State. We also took recent per-capita income levels into account. However, we did not take into account the costs and effects of emission reductions on GDP. This PBL Note analyses two possible scenarios that differ in the target assumed for the least wealthy Member State, in order to assess the effects of differing assumptions on the 2030 non-ETS targets. These scenarios should be considered as 'what if' scenarios and not as political positions

Plasma conditions generated by interaction of a high brightness, prepulse free Raman amplified KrF laser pulse with solid targets

International Nuclear Information System (INIS)

Riley, D.; Gizzi, L.A.; Khattak, F.Y.; Mackinnon, A.J.; Viana, S.M.; Willi, O.

1992-01-01

A high brightness, Raman amplified KrF laser has been used to irradiate solid targets with 12 ps laser pulses at intensities above 10 15 W/cm 2 without the presence of a preformed plasma caused by low level amplified spontaneous emission prepulse. Time-resolved x-ray spectroscopy of the K-shell emission from aluminum was used to infer electron densities in excess of 10 23 cm -3 at temperatures of several hundred electronvolts

Ultra-Short Laser Absorption In Solid Targets

International Nuclear Information System (INIS)

Harfouche, A.; Bendib, A.

2008-01-01

With the rapid development and continuously improving technology of subpicosecond laser pulse generation, new interesting physical problems are now investigated. Among them the laser light absorption in solid targets. During the interaction with solid targets, high intensity laser pulses are absorbed by electrons in optical skin depths, leading to rapid ionization before that significant ablation of solid material takes place. The ultra-short laser is absorbed in the overdense plasma through the electron-ion collisions (normal skin effect) or collisionless mechanisms (anomalous skin effect or sheath inverse bremsstrahlung). These two regimes depend on the laser intensity, the plasma temperature and the ionization state Z. In this work we solve numerically the Fokker-Planck equation to compute the electron distribution function in the skin layer. In the second step we compute the surface impedance and we deduce the absorption coefficient.

Can China benefit from adopting a binding emissions target?

International Nuclear Information System (INIS)

Schmidt, Robert C.; Marschinski, Robert

2010-01-01

In the run-up to the Copenhagen climate summit, the USA announced an emissions reduction target of 17% by 2020 (relative to 2005), and the EU of 20-30% (relative to 1990). For the same time horizon, China offered to reduce the CO 2 -intensity of its economy by 40-45% (relative to 2005), but rejects a legally binding commitment. We use the targets announced by the EU and the USA to analyze the potential gain for China if it were to adopt a binding emissions target and join an international emissions trading scheme. We show that China would likely benefit from choosing a binding target well below its projected baseline emissions for 2020.

Characterization of actinide targets by low solid-angle alpha particle counting

CERN Document Server

Denecke, B; Pauwels, J; Robouch, P; Gilliam, D M; Hodge, P; Hutchinson, J M R; Nico, J S

1999-01-01

Actinide samples were characterized in an interlaboratory comparison between IRMM and NIST, including alpha-particle counting at defined low solid angle and counting in a 2 pi proportional gas counter. For this comparison, nine sup 2 sup 3 sup 3 UF sub 4 samples with high uniformity in the layer thickness were prepared at IRMM by deposition under vacuum. Polished silicon wafers were used as source substrates, and these were rotated during the deposition using a planetary rotation system. The estimated uncertainties for the defined low solid-angle methods were about 0.1% at both NIST and IRMM. The agreement of reported alpha-particle emission rates in the energy range 2.5-5.09 MeV was better than or equal to 0.02% for the defined solid-angle methods. When comparing total alpha-particle emission rates over the larger energy range 0-9 MeV (which includes all emissions from the daughter nuclides and the impurities), the agreement of the defined solid-angle methods was better than or equal to 0.05%. The 2 pi propo...

Ion emission in solids bombarded with Aun+ (n = 1 - 9) clusters accelerated within the 0.15 - 1.25 MeV energy range

International Nuclear Information System (INIS)

Wehbe, Nimer

2006-06-01

This experimental work is devoted to the study of the ion emission in solids at the impact of gold clusters of energies within 0.15 to 1.25 MeV range. The physics of ion-solid collisions and the theoretical models of sputtering of solids under ion bombardment are presented in the first chapter. The chapter no. 2 deals with the description of the experimental setup. The study of a gold target allowed to evidence the role of the size and energy of the clusters in determining the emission intensity and the mass distribution of the ions. The 4. chapter gives results from the study of cesium iodide in which the intense emission of CsI clusters could be investigated quantitatively due to multiplicity measurements. Finally, the chapter no. 5 was devoted to the study of a biologic molecule, the phenylalanine, and of a pesticide molecule, chlorosulfuron. This work evidenced the importance of clusters for surface analyses by mass spectrometry

On Secondary Electron Emission from Solid H2 and D2

DEFF Research Database (Denmark)

Schou, Jørgen; Sørensen, H.

1978-01-01

The emission of secondary electrons from solid hydrogen (H2 , D2, T2) is often considered to be of importance for the interaction between a fusion plasma and pellets of solid hydrogens. A set-up was therefore built for studies of interactions between energetic particles and solid hydrogens. Studies...... of secondary electron emission (SEE) from solid H2 and D2 were made for incidence of electrons up to 3 keV and for incidence of ions of hydrogen, deuterium, and helium up to 10 keV. The measurements were made for normal incidence, and in some cases also for oblique incidence. The SEE coefficients for solid H2...... is always 0.65-0.70 times that for solid D2. This difference is attributed to different losses to vibrational states in H2 and D2 for the low energy electrons. Measurements were also made on solid para-H2 with both electrons and hydrogen ions. There was no difference from the results for normal H2, which...

Gaseous emissions during concurrent combustion of biomass and non-recyclable municipal solid waste.

Science.gov (United States)

Laryea-Goldsmith, René; Oakey, John; Simms, Nigel J

2011-02-01

Biomass and municipal solid waste offer sustainable sources of energy; for example to meet heat and electricity demand in the form of combined cooling, heat and power. Combustion of biomass has a lesser impact than solid fossil fuels (e.g. coal) upon gas pollutant emissions, whilst energy recovery from municipal solid waste is a beneficial component of an integrated, sustainable waste management programme. Concurrent combustion of these fuels using a fluidised bed combustor may be a successful method of overcoming some of the disadvantages of biomass (high fuel supply and distribution costs, combustion characteristics) and characteristics of municipal solid waste (heterogeneous content, conflict with materials recycling). It should be considered that combustion of municipal solid waste may be a financially attractive disposal route if a 'gate fee' value exists for accepting waste for combustion, which will reduce the net cost of utilising relatively more expensive biomass fuels. Emissions of nitrogen monoxide and sulphur dioxide for combustion of biomass are suppressed after substitution of biomass for municipal solid waste materials as the input fuel mixture. Interactions between these and other pollutants such as hydrogen chloride, nitrous oxide and carbon monoxide indicate complex, competing reactions occur between intermediates of these compounds to determine final resultant emissions. Fluidised bed concurrent combustion is an appropriate technique to exploit biomass and municipal solid waste resources, without the use of fossil fuels. The addition of municipal solid waste to biomass combustion has the effect of reducing emissions of some gaseous pollutants.

Estimation of Methane Emissions from Municipal Solid Waste Landfills in China Based on Point Emission Sources

Directory of Open Access Journals (Sweden)

Cai Bo-Feng

2014-01-01

Citation: Cai, B.-F., Liu, J.-G., Gao, Q.-X., et al., 2014. Estimation of methane emissions from municipal solid waste landfills in China based on point emission sources. Adv. Clim. Change Res. 5(2, doi: 10.3724/SP.J.1248.2014.081.

Spontaneous radiation emission during penetration of ions in solids

International Nuclear Information System (INIS)

Miraglia, J.E.; Pacher, M.C.

1988-01-01

In this work, the principal continuum radiative emission processes, which occur during the penetration of ions in solids or gases, are resumed. The characteristics of the following processes are discussed: secondary electron bremsstrahlung (SEB), atomic bremsstrahlung (AB), and internuclear bremsstrahlung (INB). Recent advances of the ion channeling effects in crystal solids on the spontaneous radiative spectra are exposed. (A.C.A.S.) [pt

Electronic excitation effects on secondary ion emission in highly charged ion-solid interaction

International Nuclear Information System (INIS)

Sekioka, T.; Terasawa, M.; Mitamura, T.; Stoeckli, M.P.; Lehnert, U.; Fehrenbach, C.

2001-01-01

In order to investigate the secondary ion emission from the surface of conductive materials bombarded by highly charged heavy ions, we have done two types of experiments. First, we have measured the yield of the sputtered ions from the surface of solid targets of conductive materials (Al, Si, Ni, Cu) bombarded by Xe q+ (q=15-44) at 300 keV (v p =0.30 a.u) and at 1.0 MeV (v p =0.54 a.u). In view of the secondary ion yields as a function of the potential energy of the projectile, the increase rates below q=35, where the potential energy amounts to 25.5 keV, were rather moderate and showed a prominent increase above q=35. These phenomena were rather strong in the case of the metal targets. Second, we have measured the energy dependence of the yield of the sputtered ions from the surface of solid targets of conductive materials (C, Al) bombarded by Xe q+ (q=30,36,44) between 76 keV (v p =0.15 a.u) and 6.0 MeV (v p =1.3 a.u). A broad enhancement of the secondary ion yield has been found for Al target bombarded by Xe 44+ . From these experimental results, the electronic excitation effects in conductive materials for impact of slow highly charged heavy ions bearing high potential energy is discussed

Electron beam produced in a transient hollow cathode discharge: beam electron distribution function, X-ray emission and solid target ablation

International Nuclear Information System (INIS)

Nistor, Magdalena

2000-01-01

This research thesis aims at a better knowledge of phenomena occurring during transient hollow cathode discharges. The author first recalls the characteristics of such a discharge which make it different from conventional pseudo-spark discharges. The objective is to characterise the electron beam produced within the discharge, and the phenomena associated with its interaction with a solid or gaseous target, leading to the production of an X ray or visible radiation. Thus, the author reports the measurement (by magnetic deflection) of the whole time-averaged electronic distribution function. Such a knowledge is essential for a better use of the electron beam in applications such as X-ray source or material ablation. As high repetition frequency pulse X ray sources are very interesting tools, he reports the development and characterisation of Bremsstrahlung X rays during a beam-target interaction. He finally addresses the implementation of a spectroscopic diagnosis for the filamentary plasma and the ablation of a solid target by the beam [fr

Gaseous emissions during concurrent combustion of biomass and non-recyclable municipal solid waste

Directory of Open Access Journals (Sweden)

Oakey John

2011-02-01

Full Text Available Abstract Background Biomass and municipal solid waste offer sustainable sources of energy; for example to meet heat and electricity demand in the form of combined cooling, heat and power. Combustion of biomass has a lesser impact than solid fossil fuels (e.g. coal upon gas pollutant emissions, whilst energy recovery from municipal solid waste is a beneficial component of an integrated, sustainable waste management programme. Concurrent combustion of these fuels using a fluidised bed combustor may be a successful method of overcoming some of the disadvantages of biomass (high fuel supply and distribution costs, combustion characteristics and characteristics of municipal solid waste (heterogeneous content, conflict with materials recycling. It should be considered that combustion of municipal solid waste may be a financially attractive disposal route if a 'gate fee' value exists for accepting waste for combustion, which will reduce the net cost of utilising relatively more expensive biomass fuels. Results Emissions of nitrogen monoxide and sulphur dioxide for combustion of biomass are suppressed after substitution of biomass for municipal solid waste materials as the input fuel mixture. Interactions between these and other pollutants such as hydrogen chloride, nitrous oxide and carbon monoxide indicate complex, competing reactions occur between intermediates of these compounds to determine final resultant emissions. Conclusions Fluidised bed concurrent combustion is an appropriate technique to exploit biomass and municipal solid waste resources, without the use of fossil fuels. The addition of municipal solid waste to biomass combustion has the effect of reducing emissions of some gaseous pollutants.

New investigations of polarized solid HD targets

International Nuclear Information System (INIS)

Honig, A.; Whisnant, C.S.

1995-01-01

Polarized solid HD targets in a frozen-spin mode, with superior nuclear physics characteristics and simple operational configurations, have previously been restricted in their deployment due to a disproportionate target production time with respect to utilization time. Recent investigations have yielded frozen-spin polarization lifetimes, at a convenient target temperature of 1.5 K, of nearly a year for both H and D at high holding fields, and of more than a week at sub-Tesla holding fields. These results, taken together with the advent of new interesting spin-physics using relatively weakly ionizing beams, such as polarized photon beams, remove the above impediment and open up the use of polarized solid HD to long duration nuclear spin-physics experiments. Large, multiple targets can be produced, retrieved from the polarization-production apparatus with a cold-transport (4 K) device, stored for very long times in inexpensive (1.5 K, 7 T) cryostats, and introduced 'off-the-shelf' into in-beam cryostats via the portable cold-transport apparatus. Various modes for achieving polarized H and/or D, as well as already achieved and expected polarization values, are reported. Experimental results are given on Kapitza resistance between the solid HD and the cooling wires necessary to obtain low temperatures during the heat-evolving polarization process. 15 mK is achievable using gold-plated aluminum wires, which constitute 15% extraneous nucleons over the number of polarizable H or D nucleons. Application to more highly ionizing beams is also given consideration. ((orig.))

Emission from open burning of municipal solid waste in India.

Science.gov (United States)

Kumari, Kanchan; Kumar, Sunil; Rajagopal, Vineel; Khare, Ankur; Kumar, Rakesh

2017-07-27

Open burning of Municipal Solid Waste (MSW) is a potential non-point source of emission, which causes greater concern especially in developing countries such as India. Lack of awareness about environmental impact of open burning, and ignorance of the fact, i.e. 'Open burning is a source of emission of carcinogenic substances' are major hindrances towards an appropriate municipal solid waste management system in India. The paper highlights the open burning of MSW practices in India, and the current and projected emission of 10 major pollutants (dioxin, furans, particulate matter, carbon monoxide, sulphur oxides, nitrogen oxides, benzene, toluene, ethyl benzene and 1-hexene) emitted due to the open burning of MSW. Waste to Energy potential of MSW was also estimated adopting effective biological and thermal techniques. Statistical techniques were applied to analyse the data and current and projected emission of various pollutants were estimated. Data pertaining to population, MSW generation and its collection efficiency were compiled for 29 States and 7 Union Territories. Thereafter, emission of 10 pollutants was measured following methodology prescribed in Intergovernmental Panel on Climate Change guideline for National Greenhouse Gas Inventories, 2006. The study revealed that people living in Metropolitan cities are more affected by emissions from open burning.

Ion emission in solids bombarded with Au{sub n}{sup +} (n = 1 - 9) clusters accelerated within the 0.15 - 1.25 MeV energy range; Emission ionique des solides a l'impact d'agregats Au{sub n}{sup +} (n=1-9) acceleres entre 0,15 et 1,25 MeV

Energy Technology Data Exchange (ETDEWEB)

Wehbe, Nimer [Universite Claude Bernard Lyon-I, 43 boulevard du 11 Novembre 1918, 69622 Villeurbanne cedex (France)

2006-06-15

This experimental work is devoted to the study of the ion emission in solids at the impact of gold clusters of energies within 0.15 to 1.25 MeV range. The physics of ion-solid collisions and the theoretical models of sputtering of solids under ion bombardment are presented in the first chapter. The chapter no. 2 deals with the description of the experimental setup. The study of a gold target allowed to evidence the role of the size and energy of the clusters in determining the emission intensity and the mass distribution of the ions. The 4. chapter gives results from the study of cesium iodide in which the intense emission of CsI clusters could be investigated quantitatively due to multiplicity measurements. Finally, the chapter no. 5 was devoted to the study of a biologic molecule, the phenylalanine, and of a pesticide molecule, chlorosulfuron. This work evidenced the importance of clusters for surface analyses by mass spectrometry.

Product specific emissions from municipal solid waste landfills

DEFF Research Database (Denmark)

Nielsen, Per Henning; Exner, Stephan; Jørgensen, Anne-Mette

1998-01-01

This paper presents and verifies the computer tool LCA-LAND for estimation of emissions from specific waste products disposed in municipal solid waste landfills in European countries for use in the inventory analysis of LCA. Examples of input data (e.g. distribution of the waste product...... in different countries, composition of the product and physical/chemical/biological properties of waste product components) and output data (e.g. estimated emissions to atmosphere and water) are given for a fictive waste product made of representative types of components (toluene, cellulose, polyvinylchloride...... (PVC), copper and chloride). Since waste products from different processes in the product system may be disposed at different landfills where they are mixed with waste originating outside the product system, the estimated emissions from specific waste products cannot be compared with measured emissions...

Product specific emissions from municipal solid waste landfills

DEFF Research Database (Denmark)

Nielsen, Per Henning; Hauschild, Michael Zwicky

1998-01-01

For the inventory analysis of environmental impacts associated with products in LCA there is a great need for estimates of emissions from waste products disposed at municipal solid waste landfills (product specific emissions). Since product specific emissions can not be calculated or measured...... directly at the landfills, they must be estimated by modelling of landfill processes. This paper presents a landfill model based on a large number of assumptions and approximations concerning landfill properties, waste product properties and characteristics of various kinds of environmental protection...... systems (e.g. landfill gas combustion units and leachate treatment units). The model is useful for estimation of emissions from waste products disposed in landfills and it has been made operational in the computer tool LCA-LAND presented in a following paper. In the model, waste products are subdivided...

National environmental targets and international emission reduction instruments

International Nuclear Information System (INIS)

Morthorst, P.E.

2003-01-01

According to the agreed burden sharing within the European Union the overall EU emission reduction target as agreed by in the Kyoto protocol is converted into national greenhouse gas reduction-targets for each of the member states. In parallel with national emission reduction initiatives common EU policies for emission reductions are considered. Currently discussed is the introduction of a market for tradable permits for CO 2 -emissions to achieve emission reductions within the power industry and other energy intensive industries. In parallel with this markets for green certificates to deploy renewable energy technologies seem to be appearing in a number of countries, among these Denmark, Italy, Sweden, Belgium (Flanders), England and Australia. Although these national initiatives for a green certificate market are fairly different, they could be a starting point for establishing a common EU certificate market. But interactions between national targets for greenhouse gas emissions and these international instruments for emission reduction are not a trivial matter, especially not seen in relation to the possible contributions of these instruments in achieving national GHG-reduction targets. The paper is split into three parts all taking a liberalised power market as starting point: The first part discusses the consequences of a general deployment of renewable energy technologies, using planning initiatives or national promotion schemes (feed-in tariffs). In the second part an international green certificate market is introduced into the liberalised power market context, substituting other national promotion schemes. Finally, in the third part a combination of an international green certificate market (TGC) and an international emission-trading scheme for CO 2 is analysed within the liberalised international power market set-up. The main conclusion is that neither the use of national renewable support schemes nor the introduction of a TGC-market into a liberalised

Greenhouse Gas Emissions from Solid and Liquid Organic Fertilizers Applied to Lettuce.

Science.gov (United States)

Toonsiri, Phasita; Del Grosso, Stephen J; Sukor, Arina; Davis, Jessica G

2016-11-01

Improper application of nitrogen (N) fertilizer and environmental factors can cause the loss of nitrous oxide (NO) to the environment. Different types of fertilizers with different C/N ratios may have different effects on the environment. The focus of this study was to evaluate the effects of environmental factors and four organic fertilizers (feather meal, blood meal, fish emulsion, and cyano-fertilizer) applied at different rates (0, 28, 56, and 112 kg N ha) on NO emissions and to track CO emissions from a lettuce field ( L.). The study was conducted in 2013 and 2014 and compared preplant-applied solid fertilizers (feather meal and blood meal) and multiple applications of liquid fertilizers (fish emulsion and cyano-fertilizer). Three days a week, NO and CO emissions were measured twice per day in 2013 and once per day in 2014 using a closed-static chamber, and gas samples were analyzed by gas chromatography. Preplant-applied solid fertilizers significantly increased cumulative NO emissions as compared with control, but multiple applications of liquid fertilizers did not. Emission factors for NO ranged from 0 to 0.1% for multiple applications of liquid fertilizers and 0.6 to 11% for preplant-applied solid fertilizers, which could be overestimated due to chamber placement over fertilizer bands. In 2014, solid fertilizers with higher C/N ratios (3.3-3.5) resulted in higher CO emissions than liquid fertilizers (C/N ratio, 0.9-1.5). Therefore, organic farmers should consider the use of multiple applications of liquid fertilizers as a means to reduce soil greenhouse gas emissions while maintaining high yields. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Modelling carbonaceous aerosol from residential solid fuel burning with different assumptions for emissions

Directory of Open Access Journals (Sweden)

R. Ots

2018-04-01

Full Text Available Evidence is accumulating that emissions of primary particulate matter (PM from residential wood and coal combustion in the UK may be underestimated and/or spatially misclassified. In this study, different assumptions for the spatial distribution and total emission of PM from solid fuel (wood and coal burning in the UK were tested using an atmospheric chemical transport model. Modelled concentrations of the PM components were compared with measurements from aerosol mass spectrometers at four sites in central and Greater London (ClearfLo campaign, 2012, as well as with measurements from the UK black carbon network.The two main alternative emission scenarios modelled were Base4x and combRedist. For Base4x, officially reported PM2.5 from the residential and other non-industrial combustion source sector were increased by a factor of four. For the combRedist experiment, half of the baseline emissions from this same source were redistributed by residential population density to simulate the effect of allocating some emissions to the smoke control areas (that are assumed in the national inventory to have no emissions from this source. The Base4x scenario yielded better daily and hourly correlations with measurements than the combRedist scenario for year-long comparisons of the solid fuel organic aerosol (SFOA component at the two London sites. However, the latter scenario better captured mean measured concentrations across all four sites. A third experiment, Redist – all emissions redistributed linearly to population density, is also presented as an indicator of the maximum concentrations an assumption like this could yield.The modelled elemental carbon (EC concentrations derived from the combRedist experiments also compared well with seasonal average concentrations of black carbon observed across the network of UK sites. Together, the two model scenario simulations of SFOA and EC suggest both that residential solid fuel emissions may be higher than

Modelling carbonaceous aerosol from residential solid fuel burning with different assumptions for emissions

Science.gov (United States)

Ots, Riinu; Heal, Mathew R.; Young, Dominique E.; Williams, Leah R.; Allan, James D.; Nemitz, Eiko; Di Marco, Chiara; Detournay, Anais; Xu, Lu; Ng, Nga L.; Coe, Hugh; Herndon, Scott C.; Mackenzie, Ian A.; Green, David C.; Kuenen, Jeroen J. P.; Reis, Stefan; Vieno, Massimo

2018-04-01

Evidence is accumulating that emissions of primary particulate matter (PM) from residential wood and coal combustion in the UK may be underestimated and/or spatially misclassified. In this study, different assumptions for the spatial distribution and total emission of PM from solid fuel (wood and coal) burning in the UK were tested using an atmospheric chemical transport model. Modelled concentrations of the PM components were compared with measurements from aerosol mass spectrometers at four sites in central and Greater London (ClearfLo campaign, 2012), as well as with measurements from the UK black carbon network.The two main alternative emission scenarios modelled were Base4x and combRedist. For Base4x, officially reported PM2.5 from the residential and other non-industrial combustion source sector were increased by a factor of four. For the combRedist experiment, half of the baseline emissions from this same source were redistributed by residential population density to simulate the effect of allocating some emissions to the smoke control areas (that are assumed in the national inventory to have no emissions from this source). The Base4x scenario yielded better daily and hourly correlations with measurements than the combRedist scenario for year-long comparisons of the solid fuel organic aerosol (SFOA) component at the two London sites. However, the latter scenario better captured mean measured concentrations across all four sites. A third experiment, Redist - all emissions redistributed linearly to population density, is also presented as an indicator of the maximum concentrations an assumption like this could yield.The modelled elemental carbon (EC) concentrations derived from the combRedist experiments also compared well with seasonal average concentrations of black carbon observed across the network of UK sites. Together, the two model scenario simulations of SFOA and EC suggest both that residential solid fuel emissions may be higher than inventory

Greenhouse gas emissions from solid waste in Beijing: The rising trend and the mitigation effects by management improvements.

Science.gov (United States)

Yu, Yongqiang; Zhang, Wen

2016-04-01

Disposal of solid waste poses great challenges to city managements. Changes in solid waste composition and disposal methods, along with urbanisation, can certainly affect greenhouse gas emissions from municipal solid waste. In this study, we analysed the changes in the generation, composition and management of municipal solid waste in Beijing. The changes of greenhouse gas emissions from municipal solid waste management were thereafter calculated. The impacts of municipal solid waste management improvements on greenhouse gas emissions and the mitigation effects of treatment techniques of greenhouse gas were also analysed. Municipal solid waste generation in Beijing has increased, and food waste has constituted the most substantial component of municipal solid waste over the past decade. Since the first half of 1950s, greenhouse gas emission has increased from 6 CO2-eq Gg y(-1)to approximately 200 CO2-eq Gg y(-1)in the early 1990s and 2145 CO2-eq Gg y(-1)in 2013. Landfill gas flaring, landfill gas utilisation and energy recovery in incineration are three techniques of the after-emission treatments in municipal solid waste management. The scenario analysis showed that three techniques might reduce greenhouse gas emissions by 22.7%, 4.5% and 9.8%, respectively. In the future, if waste disposal can achieve a ratio of 4:3:3 by landfill, composting and incineration with the proposed after-emission treatments, as stipulated by the Beijing Municipal Waste Management Act, greenhouse gas emissions from municipal solid waste will decrease by 41%. © The Author(s) 2016.

Cooking with Fire: The Mutagenicity- and PAH-Emission Factors of Solid-Fuel Cookstoves

Science.gov (United States)

Emissions from solid fuels used for cooking cause ~4 million premature deaths per year. Advanced solid-fuel cookstoves are a potential solution, but they should be assessed by appropriate performance indicators, including biological effects. We evaluated two categories of solid...

Modification of K-line emission profiles in laser-created solid-density plasmas

International Nuclear Information System (INIS)

Sengebusch, A.; Reinholz, H.; Roepke, G.

2010-01-01

Complete text of publication follows. X-ray emissions in the keV energy range have shown to be suitable radiation to investigate the properties of laser-created solid-density plasmas. We use the modifications of inner shell transitions due to the environment to characterize these plasmas. A theoretical treatment of spectral line profiles based on a self-consistent ion sphere model is applied on moderately ionized mid-Z materials, such as titanium, silicon and chlorine. We observe large contributions of satellite transitions due to M-shell ionization and excitation. To determine the composition a mixture of various excited and ionized ionic states embedded in a plasma has to be considered. Plasma polarization effects that cause shifts of the emission and ionization energies are taken into account. K-line profiles are calculated for bulk temperatures up to 100 eV and free electron densities up to 10 24 cm -3 in order to analyze recent measurements with respect to the plasma parameters of electron heated target regions. Moreover, in high-intensity laser-matter interactions, inevitable prepulses are likely to create preplasma and shocks within the target before the main pulse arrives. We investigate the influence of density gradients due to prepulses on the spectral profiles. Further, radial bulk temperature distributions as well the composition of the created warm dense matter are inferred.

Technology of solid-fuel-layer targets for laser-fusion experiments

International Nuclear Information System (INIS)

Musinski, D.L.; Henderson, T.M.; Pattinson, T.R.; Tarvin, J.A.

1979-01-01

An apparatus which produces uniform solid-fuel layers in glass-shell targets for laser irradiation is described. A low-power cw laser pulse is used to vaporize the fuel within a previously frozen target which is maintained in a cold-helium environment by a cryogenic shroud. The rapid refreezing that follows the pulse forms a uniform fuel layer on the inner surface of the glass shell. This apparatus and technique meet the restrictions imposed by the experimental target chamber. The method does not perturb the target position; nor does it preclude the usual diagnostic experimets since the shroud is retracted before the main laser pulse arrives. Successful laser irradiation and implosion of solid-fuel-layer targets at KMSF have confirmed the effectiveness and reliability of this system and extended the range of laser-target-interaction studies in the cryogenic regime

Emission control with route optimization in solid waste collection ...

Indian Academy of Sciences (India)

system is used, route distance and route time will be decreased by 24·6% and. 44·3% as ... Keywords. Exhaust emission; route optimization; solid waste collection; GIS, .... Catchment areas for a sales campaign can be analysed. Customers ...

40 CFR 60.752 - Standards for air emissions from municipal solid waste landfills.

Science.gov (United States)

2010-07-01

... municipal solid waste landfills. 60.752 Section 60.752 Protection of Environment ENVIRONMENTAL PROTECTION... of Performance for Municipal Solid Waste Landfills § 60.752 Standards for air emissions from municipal solid waste landfills. (a) Each owner or operator of an MSW landfill having a design capacity less...

Molecular emissions from laser--solid-target interactions

International Nuclear Information System (INIS)

Greig, J.R.

1977-01-01

When a high-power Nd/glass laser pulse is incident on a polyethylene target, a bright plasma plume is created. Subsequently, a cloud of un-ionized gas is formed which contains 10--100 times the amount of material in the plasma plume. This gas cloud is cold (expansion velocity approx.10 5 cm/sec) and dense (n> or approx. =10 19 ). It is shown to contain diatomic molecules of carbon C 2 by heating the core of the cloud with the pulse from a 1-kJ TEA CO 2 laser. Then, the C 2 molecules in the cold outer regions of the cloud are seen in absorption on the light emitted by the hot core

Thermal Analysis of Fission Moly Target Solid Waste Storage

Energy Technology Data Exchange (ETDEWEB)

Son, Hyung Min; Park, Jonghark [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

There are various ways to produce Mo-99. Among them, nuclear transmutation of uranium target became the major one owing to its superior specific activity. After the fission molybdenum (FM) target is irradiated, it is transported to treatment facility to extract wanted isotope. During the process, various forms of wastes are produced including filter cake and other solid wastes. The filter cake is mostly consisted of decaying uranium compounds. The solid wastes are then packaged and moved to storage facility which will stay there for considerable amount of time. Being the continuous source of heat, the solid wastes are required to be cooled for the certain amount of time before transported to the storage area. In this study, temperature evaluation of the storage facility is carried out with pre-cooling time sensitivity to check its thermal integrity. In this study, thermal analysis on the FM target solid waste storage is performed. Finite volume method is utilized to numerically discretize and solve the geometry of interest. Analysis shows that the developed method can simulate temperature behavior during storage process, but needs to be checked against other code to see calculation accuracy. Highest temperature distribution is observed when every hole is filled with waste containers. Sensitivity results on pre-cooling time shows that at least 13 months of cooling is necessary to keep the structure integrity.

EU GHG Emission Targets: 'Mind the gap'

International Nuclear Information System (INIS)

Lojodice, Ilaria

2012-06-01

In Durban, the European Union has been able to overcome the traditional dividing lines between developed and developing countries, setting a 'road-map' for a post-Kyoto framework. This would see countries conclude an 'agreed outcome with legal force' on emissions targets by 2015. Was this a key goal or a partial success for EU climate diplomacy? The main concerns are that the second commitment period would only come into force by 2021, and that necessary carbon cuts are not be increased before 2020. The direct by-product for the EU victory has been the awakening of the debate about raising emissions reductions to 30%. In fact, as stated in the Low Carbon Road-map, the EU has adopted a target of cutting emissions by 20% to by 2020, and of moving to a 30% reduction target if the conditions are right. Is this finally the time for Europe to improve its performance, even if it means going it alone? The EU has always been a strong defender of the Kyoto Protocol under certain constraints, such as developing and emerging countries entering into the deal. But does the EU have all the right assets to fight for this? Where is Europe in achieving its 2020 goal? In essence, this paper provides an estimate of what EU emissions could be in 2020, and how they stand compared to Kyoto and 20% objective of the 2020 strategy. (author)

Polarized proton and deuteron solid HD targets

International Nuclear Information System (INIS)

Honig, A.

1977-01-01

A decade has now elapsed since HD was proposed as a polarized proton and deuteron target with exceptionally desirable properties. These include a very high free proton proportion, independently polarizable proton and deuteron systems, and a ''frozen-spin'' mode of operation which allows separation of the functions of production and utilization of the highly polarized target. A discussion is given of what can be expected of the polarized HD system right now, without further research. The basic features of solid HD pertinent to its use as a ''frozen-spin'' target are outlined, then a summary is given of the particular experimental results which support the contention that the target will perform successfully, and finally, some feasible operating modes and the expected performances from them are presented

Global radiative effects of solid fuel cookstove aerosol emissions

Science.gov (United States)

Huang, Yaoxian; Unger, Nadine; Storelvmo, Trude; Harper, Kandice; Zheng, Yiqi; Heyes, Chris

2018-04-01

We apply the NCAR CAM5-Chem global aerosol-climate model to quantify the net global radiative effects of black and organic carbon aerosols from global and Indian solid fuel cookstove emissions for the year 2010. Our assessment accounts for the direct radiative effects, changes to cloud albedo and lifetime (aerosol indirect effect, AIE), impacts on clouds via the vertical temperature profile (semi-direct effect, SDE) and changes in the surface albedo of snow and ice (surface albedo effect). In addition, we provide the first estimate of household solid fuel black carbon emission effects on ice clouds. Anthropogenic emissions are from the IIASA GAINS ECLIPSE V5a inventory. A global dataset of black carbon (BC) and organic aerosol (OA) measurements from surface sites and aerosol optical depth (AOD) from AERONET is used to evaluate the model skill. Compared with observations, the model successfully reproduces the spatial patterns of atmospheric BC and OA concentrations, and agrees with measurements to within a factor of 2. Globally, the simulated AOD agrees well with observations, with a normalized mean bias close to zero. However, the model tends to underestimate AOD over India and China by ˜ 19 ± 4 % but overestimate it over Africa by ˜ 25 ± 11 % (± represents modeled temporal standard deviations for n = 5 run years). Without BC serving as ice nuclei (IN), global and Indian solid fuel cookstove aerosol emissions have net global cooling radiative effects of -141 ± 4 mW m-2 and -12 ± 4 mW m-2, respectively (± represents modeled temporal standard deviations for n = 5 run years). The net radiative impacts are dominated by the AIE and SDE mechanisms, which originate from enhanced cloud condensation nuclei concentrations for the formation of liquid and mixed-phase clouds, and a suppression of convective transport of water vapor from the lower troposphere to the upper troposphere/lower stratosphere that in turn leads to reduced ice cloud formation. When BC is allowed

[Research advances in control of N2O emission from municipal solid waste landfill sites].

Science.gov (United States)

Cai, Chuan-Yu; Li, Bo; Lü, Hao-Hao; Wu, Wei-Xiang

2012-05-01

Landfill is one of the main approaches for municipal solid waste treatment, and landfill site is a main emission source of greenhouse gases nitrous oxide (N2O) and methane (CH4). As a high-efficient trace greenhouse gas, N2O has a very high warming potential, with a warming capacity 296 times of CO2, and has a long-term stability in atmosphere, giving greater damage to the ozone layer. Aiming at the researches in the control of N2O emission from municipal solid waste landfill sites, this paper summarized the characteristics and related affecting factors of the N2O emission from the landfill sites, and put forward a series of the measures adaptable to the N2O emission control of present municipal solid waste landfill sites in China. Some further research focuses on the control of N2O emission from the landfill sites were also presented.

Mercury emissions from municipal solid waste combustors

Energy Technology Data Exchange (ETDEWEB)

1993-05-01

This report examines emissions of mercury (Hg) from municipal solid waste (MSW) combustion in the United States (US). It is projected that total annual nationwide MSW combustor emissions of mercury could decrease from about 97 tonnes (1989 baseline uncontrolled emissions) to less than about 4 tonnes in the year 2000. This represents approximately a 95 percent reduction in the amount of mercury emitted from combusted MSW compared to the 1989 mercury emissions baseline. The likelihood that routinely achievable mercury emissions removal efficiencies of about 80 percent or more can be assured; it is estimated that MSW combustors in the US could prove to be a comparatively minor source of mercury emissions after about 1995. This forecast assumes that diligent measures to control mercury emissions, such as via use of supplemental control technologies (e.g., carbon adsorption), are generally employed at that time. However, no present consensus was found that such emissions control measures can be implemented industry-wide in the US within this time frame. Although the availability of technology is apparently not a limiting factor, practical implementation of necessary control technology may be limited by administrative constraints and other considerations (e.g., planning, budgeting, regulatory compliance requirements, etc.). These projections assume that: (a) about 80 percent mercury emissions reduction control efficiency is achieved with air pollution control equipment likely to be employed by that time; (b) most cylinder-shaped mercury-zinc (CSMZ) batteries used in hospital applications can be prevented from being disposed into the MSW stream or are replaced with alternative batteries that do not contain mercury; and (c) either the amount of mercury used in fluorescent lamps is decreased to an industry-wide average of about 27 milligrams of mercury per lamp or extensive diversion from the MSW stream of fluorescent lamps that contain mercury is accomplished.

A polarized solid {sup 3}He target for neutron transmission experiments

Energy Technology Data Exchange (ETDEWEB)

Keith, C.D. [North Carolina State Univ., Raleigh, NC (United States)]|[Triangle Universities Nuclear Laboratory, Durham, NC 27708-0308 (United States); Gould, C.R. [North Carolina State Univ., Raleigh, NC (United States)]|[Triangle Universities Nuclear Laboratory, Durham, NC 27708-0308 (United States); Haase, D.G. [North Carolina State Univ., Raleigh, NC (United States)]|[Triangle Universities Nuclear Laboratory, Durham, NC 27708-0308 (United States); Huffman, P.R. [Duke University, Durham, NC 27708-0308 (United States)]|[Triangle Universities Nuclear Laboratory, Durham, NC 27708-0308 (United States); Roberson, N.R. [Duke University, Durham, NC 27708-0308 (United States)]|[Triangle Universities Nuclear Laboratory, Durham, NC 27708-0308 (United States); Seely, M.L. [North Carolina State Univ., Raleigh, NC (United States)]|[Triangle Universities Nuclear Laboratory, Durham, NC 27708-0308 (United States); Tornow, W. [Duke University, Durham, NC 27708-0308 (United States)]|[Triangle Universities Nuclear Laboratory, Durham, NC 27708-0308 (United States); Wilburn, W.S. [Duke University, Durham, NC 27708-0308 (United States)]|[Triangle Universities Nuclear Laboratory, Durham, NC 27708-0308 (United States)

1995-04-01

We describe the construction and operation of a solid {sup 3}He polarized nuclear target which we have used for measurements of the spin dependence of the n-{sup 3}He interaction at MeV energies. The target, which contains 0.4 mole of {sup 3}He was polarized to 38% at 12 mK in a field of 7 T. The target is suitable for nuclear physics measurements which are insensitive to the large magnetic field and produce beam heating of tenths of microwatts.We discuss refinements and paths to improved solid {sup 3}He targets at higher polarizations and lower fields. ((orig.)).

Targeting solid tumors with non-pathogenic obligate anaerobic bacteria.

Science.gov (United States)

Taniguchi, Shun'ichiro; Fujimori, Minoru; Sasaki, Takayuki; Tsutsui, Hiroko; Shimatani, Yuko; Seki, Keiichi; Amano, Jun

2010-09-01

Molecular-targeting drugs with fewer severe adverse effects are attracting great attention as the next wave of cancer treatment. There exist, however, populations of cancer cells resistant to these drugs that stem from the instability of tumor cells and/or the existence of cancer stem cells, and thus specific toxicity is required to destroy them. If such selectivity is not available, these targets may be sought out not by the cancer cell types themselves, but rather in their adjacent cancer microenvironments by means of hypoxia, low pH, and so on. The anaerobic conditions present in malignant tumor tissues have previously been regarded as a source of resistance in cancer cells against conventional therapy. However, there now appears to be a way to make use of these limiting factors as a selective target. In this review, we will refer to several trials, including our own, to direct attention to the utilizable anaerobic conditions present in malignant tumor tissues and the use of bacteria as carriers to target them. Specifically, we have been developing a method to attack solid cancers using the non-pathogenic obligate anaerobic bacterium Bifidobacterium longum as a vehicle to selectively recognize and target the anaerobic conditions in solid cancer tissues. We will also discuss the existence of low oxygen pressure in tumor masses in spite of generally enhanced angiogenesis, overview current cancer therapies, especially the history and present situation of bacterial utility to treat solid tumors, and discuss the rationality and future possibilities of this novel mode of cancer treatment. © 2010 Japanese Cancer Association.

Solid-immersion fluorescence microscopy with increased emission and super resolution

Energy Technology Data Exchange (ETDEWEB)

Liau, Z. L.; Porter, J. M. [Lincoln Laboratory, Massachusetts Institute of Technology, Lexington, Massachusetts 02420 (United States); Liau, A. A.; Chen, J. J. [Institute for Medical Engineering and Science, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Salmon, W. C. [Whitehead Institute, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Sheu, S. S. [Department of Medicine, Jefferson Medical College, Philadelphia, Pennsylvania 19107 (United States)

2015-01-07

We investigate solid-immersion fluorescence microscopy suitable for super-resolution nanotechnology and biological imaging, and have observed limit of resolution as small as 15 nm with microspheres, mitochondria, and chromatin fibers. We have further observed that fluorescence efficiency increases with excitation power density, implicating appreciable stimulated emission and increased resolution. We discuss potential advantages of the solid-immersion microscopy, including combined use with previously established super-resolution techniques for reaching deeper beyond the conventional diffraction limit.

Recovery of uranium from an irradiated solid target after removal of molybdenum-99 produced from the irradiated target

Science.gov (United States)

Reilly, Sean Douglas; May, Iain; Copping, Roy; Dale, Gregory Edward

2017-10-17

A process for minimizing waste and maximizing utilization of uranium involves recovering uranium from an irradiated solid target after separating the medical isotope product, molybdenum-99, produced from the irradiated target. The process includes irradiating a solid target comprising uranium to produce fission products comprising molybdenum-99, and thereafter dissolving the target and conditioning the solution to prepare an aqueous nitric acid solution containing irradiated uranium. The acidic solution is then contacted with a solid sorbent whereby molybdenum-99 remains adsorbed to the sorbent for subsequent recovery. The uranium passes through the sorbent. The concentrations of acid and uranium are then adjusted to concentrations suitable for crystallization of uranyl nitrate hydrates. After inducing the crystallization, the uranyl nitrate hydrates are separated from a supernatant. The process results in the purification of uranyl nitrate hydrates from fission products and other contaminants. The uranium is therefore available for reuse, storage, or disposal.

L-shell emission from high-Z solid targets by intense (10{sup 19}W/cm{sup 2}) irradiation with a 248nm laser

Energy Technology Data Exchange (ETDEWEB)

Nelson, T. R.; Borisov, A. B.; Boyer, K.; Schroeder, W. A.; Santoro, J.; Van Tassle, A. J.; Rhodes, C. K.; Luk, T. S.; Cameron, S.; Longworth, J. W.; McPherson, A.

1999-11-22

Efficient (1.2% yield) multikilovolt x-ray emission from Ba(L) (2.4--2.8{angstrom}) and Gd(L) (1.7--2.1{angstrom}) is produced by ultraviolet (248nm) laser-excited BaF{sub 2} and Gd solids. The high efficiency is attributed to an inner shell-selective collisional electron ejection.

The neutronic performance of solid-target alternatives for SINQ

International Nuclear Information System (INIS)

Atchison, F.

1991-01-01

The results from calculations of the neutronic performance of three possible 'solid' targets and that of the current version of the liquid Pb-Bi target are presented. Two are 'conventional' transverse cooled plate structures, one using tantalum, the other tungsten. The third is a Pb-shot based pebble-bed design. Some general results on the effect of neutron absorption on the performance of the Pebble-bed target are given. (author)

Solid targets for production of radioisotopes with cyclotron

International Nuclear Information System (INIS)

Paredes G, L.; Balcazar G, M.

1999-01-01

The design of targets for production of radioisotopes and radiopharmaceuticals of cyclotron to medical applications requires a detailed analysis of several variables such as: cyclotron operation conditions, choice of used materials as target and their physicochemical characteristics, activity calculation, the yielding of each radioisotope by irradiation, the competition of nuclear reactions in function of the projectiles energy and the collision processes amongst others. The objective of this work is to determine the equations for the calculation for yielding of solid targets at the end of the proton irradiation. (Author)

Poly(ethylene glycol)/carbon quantum dot composite solid films exhibiting intense and tunable blue–red emission

International Nuclear Information System (INIS)

Hao, Yanling; Gan, Zhixing; Xu, Jiaqing; Wu, Xinglong; Chu, Paul K.

2014-01-01

Highlights: • Poly(ethylene glycol)/carbon quantum dots (PEG/CQDs) composite solid films exhibiting strong and tunable blue–red emission were prepared. Successful preparation of tunable emitting CQDs solid films can extend the application of carbon quantum dots in photoelectric devices. • The mechanism of the tunable emission from the PEG/CQDs composite solid films was discussed. • On the basis of the characteristics of the PL from solid films in this work, the complex PL origins of CQDs were further defined. The PL mechanism provides insights into the fluorescence mechanism of CQDs and may promotes their applications. • Poly(ethylene glycol); carbon quantum dots; Strong and tunable blue-red emission; The fluorescent quantum yield of 12.6%. - Abstract: Although carbon quantum dots (CQDs) possess excellent luminescence properties, it is a challenge to apply water-soluble CQDs to tunable luminescent devices. Herein, quaternary CQDs are incorporated into poly(ethylene glycol) to produce poly(ethylene glycol)/CQD composite solid films which exhibit strong and tunable blue–red emission. The fluorescent quantum yield reaches 12.6% which is comparable to that of many liquid CQDs and the photoluminescence characteristics are determined to elucidate the fluorescence mechanism. The CQD solid films with tunable optical properties bode well for photoelectric devices especially displays

Dynamics of Laser-Driven Shock Waves in Solid Targets

Science.gov (United States)

Aglitskiy, Y.; Karasik, M.; Velikovich, A. L.; Serlin, V.; Weaver, J.; Schmitt, A. J.; Obenschain, S. P.; Grun, J.; Metzler, N.; Zalesak, S. T.; Gardner, J. H.; Oh, J.; Harding, E. C.

2009-11-01

Accurate shock timing is a key issue of both indirect- and direct-drive laser fusions. The experiments on the Nike laser at NRL presented here were made possible by improvements in the imaging capability of our monochromatic x-ray diagnostics based on Bragg reflection from spherically curved crystals. Side-on imaging implemented on Nike makes it possible to observe dynamics of the shock wave and ablation front in laser-driven solid targets. We can choose to observe a sequence of 2D images or a continuous time evolution of an image resolved in one spatial dimension. A sequence of 300 ps snapshots taken using vanadium backlighter at 5.2 keV reveals propagation of a shock wave in a solid plastic target. The shape of the shock wave reflects the intensity distribution in the Nike beam. The streak records with continuous time resolution show the x-t trajectory of a laser-driven shock wave in a 10% solid density DVB foam.

Zero emission targets as long-term global goals for climate protection

International Nuclear Information System (INIS)

Rogelj, Joeri; Riahi, Keywan; Schaeffer, Michiel; Hare, William; Meinshausen, Malte; Knutti, Reto; Alcamo, Joseph

2015-01-01

Recently, assessments have robustly linked stabilization of global-mean temperature rise to the necessity of limiting the total amount of emitted carbon-dioxide (CO 2 ). Halting global warming thus requires virtually zero annual CO 2 emissions at some point. Policymakers have now incorporated this concept in the negotiating text for a new global climate agreement, but confusion remains about concepts like carbon neutrality, climate neutrality, full decarbonization, and net zero carbon or net zero greenhouse gas (GHG) emissions. Here we clarify these concepts, discuss their appropriateness to serve as a long-term global benchmark for achieving temperature targets, and provide a detailed quantification. We find that with current pledges and for a likely (>66%) chance of staying below 2 °C, the scenario literature suggests net zero CO 2 emissions between 2060 and 2070, with net negative CO 2 emissions thereafter. Because of residual non-CO 2 emissions, net zero is always reached later for total GHG emissions than for CO 2 . Net zero emissions targets are a useful focal point for policy, linking a global temperature target and socio-economic pathways to a necessary long-term limit on cumulative CO 2 emissions. (letter)

Prepulse and amplified spontaneous emission effects on the interaction of a petawatt class laser with thin solid targets

Energy Technology Data Exchange (ETDEWEB)

Esirkepov, Timur Zh. [QuBS, Japan Atomic Energy Agency, Kizugawa, Kyoto 619-0215 (Japan); Koga, James K., E-mail: koga.james@jaea.go.jp [QuBS, Japan Atomic Energy Agency, Kizugawa, Kyoto 619-0215 (Japan); Sunahara, Atsushi [Institute for Laser Technology, 2-6 Yamadaoka Suita, Osaka 565-0871 (Japan); Morita, Toshimasa; Nishikino, Masaharu [QuBS, Japan Atomic Energy Agency, Kizugawa, Kyoto 619-0215 (Japan); Kageyama, Kei [Graduate School of Engineering, Osaka University, Osaka 565-0871 (Japan); Nagatomo, Hideo; Nishihara, Katsunobu [Institute of Laser Engineering, 2-6 Yamadaoka Suita, Osaka 565-0871 (Japan); Sagisaka, Akito; Kotaki, Hideyuki; Nakamura, Tatsufumi; Fukuda, Yuji; Okada, Hajime; Pirozhkov, Alexander S.; Yogo, Akifumi; Nishiuchi, Mamiko; Kiriyama, Hiromitsu; Kondo, Kiminori; Kando, Masaki [QuBS, Japan Atomic Energy Agency, Kizugawa, Kyoto 619-0215 (Japan); Bulanov, Sergei V. [QuBS, Japan Atomic Energy Agency, Kizugawa, Kyoto 619-0215 (Japan); A.M. Prokhorov Institute of General Physics of RAS, Vavilova st. 38, Moscow 117942 (Russian Federation); Moscow Institute of Physics and Technology, Dolgoprudny, Moscow Region 141700 (Russian Federation)

2014-05-01

When a finite contrast petawatt laser pulse irradiates a micron-thick foil, a prepulse (including amplified spontaneous emission) creates a preplasma, where an ultrashort relativistically strong portion of the laser pulse (the main pulse) acquires higher intensity due to relativistic self-focusing and undergoes fast depletion transferring energy to fast electrons. If the preplasma thickness is optimal, the main pulse can reach the target accelerating fast ions more efficiently than an ideal, infinite contrast, laser pulse. A simple analytical model of a target with preplasma formation is developed and the radiation pressure dominant acceleration of ions in this target is predicted. The preplasma formation by a nanosecond prepulse is analyzed with dissipative hydrodynamic simulations. The main pulse interaction with the preplasma is studied with multi-parametric particle-in-cell simulations. The optimal conditions for hundreds of MeV ion acceleration are found with accompanying effects important for diagnostics, including high-order harmonics generation.

Study of secondary electron emission from thin carbon targets with swift charged particles: heavy ions, hydrogen ions; Etude experimentale de l`emission electronique secondaire de cibles minces de carbone sous l`impact de projectiles rapides: ions lourds, ions hydrogene (atomiques, moleculaires ou sous forme d`agregats)

Energy Technology Data Exchange (ETDEWEB)

Billebaud, A

1995-07-12

The main subject of this work is the study of electron emission from the two surfaces of thin solid targets bombarded with swift charged particles. The slowing down of swift ions in matter is mainly due to inelastic interaction with target electrons (ionization, excitation): the energy transfer to target electrons is responsible for the secondary electron emission process. The phenomenological and theoretical descriptions of this phenomena are the subject of the first chapter. We focused on secondary electron emission induced by different kind of projectiles on thin carbon foils. In chapter two we describe hydrogen cluster induced electron emission measurement between 40 and 120 keV/proton. These projectiles, composed of several atoms, allowed us to study and highlight collective effects of the electron emission process. We extended our study of electron emission to molecular (H{sub 2}{sup +}, H{sub 3}{sup +}) and composite (H{sup -}, H{sup 0}) projectiles at higher energies (<= 2 MeV): we have designed an experimental set-up devoted to electron emission statistics measurements which allowed us to study, among others things, the role of projectile electrons in secondary electron emission. This experiment is described in the third chapter. Finally, the fourth chapter describes new measurements of electron emission induced by energetic (13 MeV/u) and highly charged argon ion provided by the medium energy beam line (SME) of GANIL (Caen), which have been analyzed in the framework of a semi-empirical model of secondary electron emission. This set of experiments brings new results on composite projectile interaction with matter, and on the consequences of high energy deposition in solids. (author).

Surface Functionalization and Targeting Strategies of Liposomes in Solid Tumor Therapy: A Review

Science.gov (United States)

Riaz, Muhammad Kashif; Riaz, Muhammad Adil; Zhang, Xue; Lin, Congcong; Wong, Ka Hong; Chen, Xiaoyu; Lu, Aiping

2018-01-01

Surface functionalization of liposomes can play a key role in overcoming the current limitations of nanocarriers to treat solid tumors, i.e., biological barriers and physiological factors. The phospholipid vesicles (liposomes) containing anticancer agents produce fewer side effects than non-liposomal anticancer formulations, and can effectively target the solid tumors. This article reviews information about the strategies for targeting of liposomes to solid tumors along with the possible targets in cancer cells, i.e., extracellular and intracellular targets and targets in tumor microenvironment or vasculature. Targeting ligands for functionalization of liposomes with relevant surface engineering techniques have been described. Stimuli strategies for enhanced delivery of anticancer agents at requisite location using stimuli-responsive functionalized liposomes have been discussed. Recent approaches for enhanced delivery of anticancer agents at tumor site with relevant surface functionalization techniques have been reviewed. Finally, current challenges of functionalized liposomes and future perspective of smart functionalized liposomes have been discussed. PMID:29315231

Surface Functionalization and Targeting Strategies of Liposomes in Solid Tumor Therapy: A Review

Directory of Open Access Journals (Sweden)

Muhammad Kashif Riaz

2018-01-01

Full Text Available Surface functionalization of liposomes can play a key role in overcoming the current limitations of nanocarriers to treat solid tumors, i.e., biological barriers and physiological factors. The phospholipid vesicles (liposomes containing anticancer agents produce fewer side effects than non-liposomal anticancer formulations, and can effectively target the solid tumors. This article reviews information about the strategies for targeting of liposomes to solid tumors along with the possible targets in cancer cells, i.e., extracellular and intracellular targets and targets in tumor microenvironment or vasculature. Targeting ligands for functionalization of liposomes with relevant surface engineering techniques have been described. Stimuli strategies for enhanced delivery of anticancer agents at requisite location using stimuli-responsive functionalized liposomes have been discussed. Recent approaches for enhanced delivery of anticancer agents at tumor site with relevant surface functionalization techniques have been reviewed. Finally, current challenges of functionalized liposomes and future perspective of smart functionalized liposomes have been discussed.

Characterization of a multi-keV x-ray source produced by nanosecond laser irradiation of a solid target: The influence of laser focus spot and target thickness

International Nuclear Information System (INIS)

Hu Guangyue; Zheng Jian; Shen Baifei; Lei Anle; Xu Zhizhan; Liu Shenye; Zhang Jiyan; Yang Jiamin; Ding Yongkun; Hu Xin; Huang Yixiang; Du Huabing; Yi Rongqing

2008-01-01

The influence of focus spot and target thickness on multi-keV x-ray sources generated by 2 ns duration laser heated solid targets are investigated on the Shenguang II laser facility. In the case of thick-foil targets, the experimental data and theoretical analysis show that the emission volume of the x-ray sources is sensitive to the laser focus spot and proportional to the 3 power of the focus spot size. The steady x-ray flux is proportional to the 5/3 power of the focus spot size of the given laser beam in our experimental condition. In the case of thin-foil targets, experimental data show that there is an optimal foil thickness corresponding to the given laser parameters. With the given laser beam, the optimal thin-foil thickness is proportional to the -2/3 power of the focus spot size, and the optimal x-ray energy of thin foil is independent of focus spot size

X-ray emission from National Ignition Facility indirect drive targets

International Nuclear Information System (INIS)

Anderson, A.T.; Managan, R.A.; Tobin, M.T.; Peterson, P.F.

1996-01-01

We have performed a series of 1-D numerical simulations of the x-ray emission from National Ignition Facility (NIF) targets. Results are presented in terms of total x-ray energy, pulse length, and spectrum. Scaling of x-ray emissions is presented for variations in both target yield and hohlraum thickness. Experiments conducted on the Nova facility provide some validation of the computational tools and methods

Carbon emission reduction targeting through process integration and fuel switching with mathematical modeling

International Nuclear Information System (INIS)

Tiew, B.J.; Shuhaimi, M.; Hashim, H.

2012-01-01

Highlights: ► CO 2 emissions reduction targeting for existing plant were categorized into three groups. ► Model for CO 2 emissions reduction targeting via combination approach was developed. ► Effect of combination approach onto HEN area efficiency was discussed. ► Proposed execution strategy can avoid HEN area efficiency deterioration. -- Abstract: Carbon emission reduction targeting is an important and effective effort for industry to contribute in controlling greenhouse gases concentration in atmosphere. Graphical approach has been proposed for CO 2 emissions reduction targeting via HEN retrofit and fuel switching. However, it involves potentially time consuming manual procedures and the quality of solutions produced greatly depends on designer’s experience and judgment. Besides, graphical approach hardly account for the cost factor during the design phase, thus potentially generate complex design. This paper introduces an MINLP model for simultaneous CO 2 emissions reduction targeting via fuel switching and HEN retrofit. A sequential model execution was proposed along with the proposed model. The application of the model on a crude preheat train case study has demonstrated its workability to generate optimal solution for targeted CO 2 emissions reduction at minimum payback period.

Emission factors of carbonaceous particulate matter and polycyclic aromatic hydrocarbons from residential solid fuel combustions

Energy Technology Data Exchange (ETDEWEB)

Shen, Guofeng [Jiangsu Academy of Environmental Science, Nanjing (China). Inst. of Atmospheric Sciences

2014-07-01

Emission inventory is basic for the understanding of environmental behaviors and potential effects of compounds, however, current inventories are often associated with relatively high uncertainties. One important reason is the lack of emission factors, especially for the residential solid fuel combustion in developing countries. In the present study, emission factors of a group of pollutants including particulate matter, organic carbon, elemental carbon (sometimes known as black carbon) and polycyclic aromatic hydrocarbons were measured for a variety of residential solid fuels including coal, crop straw, wood, and biomass pellets in rural China. The study provided a large number of emission factors that can be further used in emission estimation. Composition profiles and isomer ratios were investigated and compared so as to be used in source apportionment. In addition, the present study identified and quantified the influence of factors like fuel moisture, volatile matter on emission performance.

Bridging greenhouse gas emissions and renewable energy deployment target: Comparative assessment of China and India

International Nuclear Information System (INIS)

Mittal, Shivika; Dai, Hancheng; Fujimori, Shinichiro; Masui, Toshihiko

2016-01-01

Highlights: • India and China’s latest renewable energy targets toward 2030 are assessed. • Carbon emission cap is in line with 2-degree target and governmental commitment. • The impacts of renewable energy on emissions and mitigation costs are quantified. - Abstract: Renewable energy has a critical role in limiting the greenhouse gas (GHG) emissions. This paper assesses the implication of aligning renewable energy deployment target with national emission reduction target for mitigation cost. The assessment methodology uses Asia-Pacific Integrated Assessment/computable general equilibrium (AIM/CGE) model to determine the mitigation cost in terms of GDP and welfare loss under alternative renewable targets in different climate-constrained scenarios. A range of country-specific emission constraints is taken to address the uncertainties related to global emission pathway and emission entitlement scheme. Comparative results show that China needs to increase its share of non-fossil fuel significantly in the primary energy mix to achieve the stringent emission reduction target compared to India. The mitigation cost in terms of economic and welfare loss can be reduced by increasing the penetration of the renewable energy to achieve the same emission reduction target. The modeling results show that coordinated national climate and renewable energy policies help to achieve the GHG emission reduction target in an efficient and cost-effective manner.

X-ray emission reduction and photon dose lowering by energy loss of fast electrons induced by return current during the interaction of a short-pulse high-intensity laser on a metal solid target

Science.gov (United States)

Compant La Fontaine, A.

2018-04-01

During the interaction of a short-pulse high-intensity laser with the preplasma produced by the pulse's pedestal in front of a high-Z metal solid target, high-energy electrons are produced, which in turn create an X-ray source by interacting with the atoms of the converter target. The current brought by the hot electrons is almost completely neutralized by a return current j → driven by the background electrons of the conductive target, and the force exerted on the hot electrons by the electric field E → which induces Ohmic heating j → .E → , produced by the background electrons, reduces the energy of the hot electrons and thus lowers the X-ray emission and photon dose. This effect is analyzed here by means of a simple 1-D temperature model which contains the most significant terms of the relativistic Fokker-Planck equation with electron multiple scattering, and the energy equations of ions, hot, and cold electrons are then solved numerically. This Ohmic heating energy loss fraction τOh is introduced as a corrective term in an improved photon dose model. For instance, for a ps laser pulse with 10 μm spot size, the dose obtained with a tantalum target is reduced by less than about 10% to 40% by the Ohmic heating, depending upon the plasma scale length, target thickness, laser parameters, and in particular its spot size. The laser and plasma parameters may be optimized to limit the effect of Ohmic heating, for instance at a small plasma scale length or small laser spot size. Conversely, others regimes not suitable for dose production are identified. For instance, the resistive heating is enhanced in a foam target or at a long plasma scale length and high laser spot size and intensity, as the mean emission angle θ0 of the incident hot electron bunch given by the ponderomotive force is small; thus, the dose produced by a laser interacting in a gas jet may be inhibited under these circumstances. The resistive heating may also be maximized in order to reduce

An analysis of Chinas CO2 emission peaking target and pathways

OpenAIRE

He, Jian-Kun

2017-01-01

China has set the goal for its CO2 emissions to peak around 2030, which is not only a strategic decision coordinating domestic sustainable development and global climate change mitigation but also an overarching target and a key point of action for Chinas resource conservation, environmental protection, shift in economic development patterns, and CO2 emission reduction to avoid climate change. The development stage where China maps out the CO2 emission peak target is earlier than that of the ...

Vanadium redox flow batteries to reach greenhouse gas emissions targets in an off-grid configuration

International Nuclear Information System (INIS)

Arbabzadeh, Maryam; Johnson, Jeremiah X.; De Kleine, Robert; Keoleian, Gregory A.

2015-01-01

Highlights: • We assess energy storage role in reaching emissions targets in an off-grid model. • The energy storage technology is vanadium redox flow battery (VRFB). • We evaluate life cycle GHG emissions and total cost of delivered electricity. • Generation mixes are optimized to meet emissions targets at the minimum cost. • For this model, integrating VRFB is economical to reach very low emissions targets. - Abstract: Energy storage may serve as a solution to the integration challenges of high penetrations of wind, helping to reduce curtailment, provide system balancing services, and reduce emissions. This study determines the minimum cost configuration of vanadium redox flow batteries (VRFB), wind turbines, and natural gas reciprocating engines in an off-grid model. A life cycle assessment (LCA) model is developed to determine the system configuration needed to achieve a variety of CO 2 -eq emissions targets. The relationship between total system costs and life cycle emissions are used to optimize the generation mixes to achieve emissions targets at the least cost and determine when VRFBs are preferable over wind curtailment. Different greenhouse gas (GHG) emissions targets are defined for the off-grid system and the minimum cost resource configuration is determined to meet those targets. This approach determines when the use of VRFBs is more cost effective than wind curtailment in reaching GHG emissions targets. The research demonstrates that while incorporating energy storage consistently reduces life cycle carbon emissions, it is not cost effective to reduce curtailment except under very low emission targets (190 g of CO2-eq/kW h and less for the examined system). This suggests that “overbuilding” wind is a more viable option to reduce life cycle emissions for all but the most ambitious carbon mitigation targets. The findings show that adding VRFB as energy storage could be economically preferable only when wind curtailment exceeds 66% for the

Design of the solid target structure and the study on the coolant flow distribution in the solid target using the 2-dimensional flow analysis

International Nuclear Information System (INIS)

Haga, Katsuhiro; Terada, Atsuhiko; Ishikura, Shuichi; Teshigawara, Makoto; Kinoshita, Hidetaka; Kobayashi, Kaoru; Kaminaga, Masaki; Hino, Ryutaro; Susuki, Akira

1999-11-01

A solid target cooled by heavy water is presently under development under the Neutron Science Research Project of the Japan Atomic Energy Research Institute (JAERI). Target plates of several millimeters thickness made of heavy metal are used as the spallation target material and they are put face to face in a row with one to two millimeters gaps in between though which heavy water flows, as the coolant. Based on the design criteria regarding the target plate cooling, the volume percentage of the coolant, and the thermal stress produced in the target plates, we conducted thermal and hydraulic analysis with a one dimensional target plate model. We choosed tungsten as the target material, and decided on various target plate thicknesses. We then calculated the temperature and the thermal stress in the target plates using a two dimensional model, and confirmed the validity of the target plate thicknesses. Based on these analytical results, we proposed a target structure in which forty target plates are divided into six groups and each group is cooled using a single pass of coolant. In order to investigate the relationship between the distribution of the coolant flow, the pressure drop, and the coolant velocity, we conducted a hydraulic analysis using the general purpose hydraulic analysis code. As a result, we realized that an uniform coolant flow distribution can be achieved under a wide range of flow velocity conditions in the target plate cooling channels from 1 m/s to 10 m/s. The pressure drop along the coolant path was 0.09 MPa and 0.17 MPa when the coolant flow velocity was 5 m/s and 7 m/s respectively, which is required to cool the 1.5 MW and 2.5 MW solid targets. (author)

Study of PAH emission from the solid fuels combustion in residential furnaces

International Nuclear Information System (INIS)

Kakareka, Sergey V.; Kukharchyk, Tamara I.; Khomich, Valery S.

2005-01-01

The procedure for and results of a test study of polycyclic aromatic hydrocarbon (PAH) emission from a few types of solid fuels combustion in residential furnaces of various designs typical for Belarus are discussed. Greatest levels of PAH emission were detected from domestic wastes and wood waste combustion. Lowest levels of PAH emission are from peat briquette combustion. It was found that PAH concentration in off-gases from firewood combustion also varies significantly depending on the type of wood: the highest values of PAH are typical for waste gases from birch firewood combustion in comparison with pine firewood combustion. Draft PAH emission factors are proposed with intended application for emission inventory of such installations

EUV stimulated emission from MgO pumped by FEL pulses

Directory of Open Access Journals (Sweden)

Philippe Jonnard

2017-09-01

Full Text Available Stimulated emission is a fundamental process in nature that deserves to be investigated and understood in the extreme ultra-violet (EUV and x-ray regimes. Today, this is definitely possible through high energy density free electron laser (FEL beams. In this context, we give evidence for soft-x-ray stimulated emission from a magnesium oxide solid target pumped by EUV FEL pulses formed in the regime of travelling-wave amplified spontaneous emission in backward geometry. Our results combine two effects separately reported in previous works: emission in a privileged direction and existence of a material-dependent threshold for the stimulated emission. We develop a novel theoretical framework, based on coupled rate and transport equations taking into account the solid-density plasma state of the target. Our model accounts for both observed mechanisms that are the privileged direction for the stimulated emission of the Mg L2,3 characteristic emission and the pumping threshold.

Influence of lateral target size on hot electron production and electromagnetic pulse emission from laser-irradiated metallic targets

International Nuclear Information System (INIS)

Chen Ziyu; Li Jianfeng; Yu Yong; Li Xiaoya; Peng Qixian; Zhu Wenjun; Wang Jiaxiang

2012-01-01

The influences of lateral target size on hot electron production and electromagnetic pulse emission from laser interaction with metallic targets have been investigated. Particle-in-cell simulations at high laser intensities show that the yield of hot electrons tends to increase with lateral target size, because the larger surface area reduces the electrostatic field on the target, owing to its expansion along the target surface. At lower laser intensities and longer time scales, experimental data characterizing electromagnetic pulse emission as a function of lateral target size also show target-size effects. Charge separation and a larger target tending to have a lower target potential have both been observed. The increase in radiation strength and downshift in radiation frequency with increasing lateral target size can be interpreted using a simple model of the electrical capacity of the target.

Influence of lateral target size on hot electron production and electromagnetic pulse emission from laser-irradiated metallic targets

Energy Technology Data Exchange (ETDEWEB)

Chen Ziyu; Li Jianfeng; Yu Yong; Li Xiaoya; Peng Qixian; Zhu Wenjun [National Key Laboratory of Shock Wave and Detonation Physics, Institute of Fluid Physics, China Academy of Engineering Physics, Mianyang, Sichuan 621900 (China); Wang Jiaxiang [State Key Laboratory of Precision Spectroscopy, East China Normal University, Shanghai 200062 (China)

2012-11-15

The influences of lateral target size on hot electron production and electromagnetic pulse emission from laser interaction with metallic targets have been investigated. Particle-in-cell simulations at high laser intensities show that the yield of hot electrons tends to increase with lateral target size, because the larger surface area reduces the electrostatic field on the target, owing to its expansion along the target surface. At lower laser intensities and longer time scales, experimental data characterizing electromagnetic pulse emission as a function of lateral target size also show target-size effects. Charge separation and a larger target tending to have a lower target potential have both been observed. The increase in radiation strength and downshift in radiation frequency with increasing lateral target size can be interpreted using a simple model of the electrical capacity of the target.

Large area solid target neutron source

International Nuclear Information System (INIS)

Crawford, J.C.; Bauer, W.

1974-01-01

A potentially useful neutron source may result from the combination of a solid deuterium-tritium loaded target with the large area, high energy ion beams from ion sources being developed for neutral beam injection. The resulting neutron source would have a large radiating area and thus produce the sizable experimental volume necessary for future studies of bulk and synergistic surface radiation effects as well as experiments on engineering samples and small components. With a 200 keV D + T + beam and 40 kW/cm 2 power dissipation on a 200 cm 2 target spot, a total neutron yield of about 4 x 10 15 n/sec may be achieved. Although the useable neutron flux from this source is limited to 1 to 2 x 10 13 n/cm 2 /sec, this flux can be produced 3 cm in front of the target and over about 300 cm 3 of experimental volume. Problems of total power dissipation, sputtering, isotopic flushing and thermal dissociation are reviewed. Neutron flux profiles and potential experimental configurations are presented and compared to other neutron source concepts. (U.S.)

Torrefaction study for energy upgrading on Indonesian biomass as low emission solid fuel

Science.gov (United States)

Alamsyah, R.; Siregar, N. C.; Hasanah, F.

2017-05-01

Torrefaction is a pyrolysis process with low heating rate and temperature lower than 300°C in an inert condition which transforms biomass into a low emission solid fuel with relatively high energy. Through the torrefaction process biomass can be altered so that the end product is easy to grind and simple in the supply chain. The research was aimed at designing torrefaction reactor and upgrading energy content of some Indonesian biomass. The biomass used consist of empty fruit bunches of oil palm (EFB), cassava peel solid waste, and cocopeat (waste of coconut fiber). These biomass were formed into briquette and pellet form and were torrified with 300°C temperature during 1.5 hours without air. The results of terrified biomass and non-torrefied biomass were compared after burning on the stove in term of energy content and air emission quality. The result shows that energy content of biomass have increased by 1.1 up to 1.36 times. Meanwhile emission air resulted from its combustion was met with Indonesian emission regulation.

Measurement of x-ray emission and thermal transport in near-solid-density plasmas heated by 130 fs laser pulses

International Nuclear Information System (INIS)

Young, B.K.; Wilson, B.G.; Price, D.F.; Stewart, R.E.

1998-01-01

Near-solid-density plasmas with peak temperatures of 370±50 eV have been generated using a high-contrast (∼10 -7 ), 400 nm, 130 fs laser pulse of intensity 3x10 17 Wcm -2 at the Ultrashort Pulse Laser at Lawrence Livermore National Laboratory. The x-ray-emission spectra from thin tracer layers of germanium, tamped by layers of plastic, were measured as a function of target depth. The results qualitatively agree with calculations based on detailed local thermodynamic equilibrium (LTE) and modified non-LTE spectroscopic opacity models using plasma conditions determined using LASNEX hydrodynamic simulations. No evidence of thermal flux inhibition into the bulk target material was observed. The experiments and detailed simulations are presented. copyright 1998 The American Physical Society

Fibers as solid, internal targets for storage rings

International Nuclear Information System (INIS)

Przewoski, B.v.

1994-01-01

It has been demonstrated that fibers or micro ribbons provide the possibility to expose solid targets to a stored ion beam. Compared to gas targets or micro particle targets fiber targets require a relatively small technical effort, since differential pumping systems are not necessary to maintain the ring vacuum. Since stationary fibers are often too thick to allow for long enough lifetimes of the stored beam to be useful for experiments, a methods has been developed to move the fiber periodically through the beam. That way, the time averaged target thickness is small compared to the thickness the same fiber would have, if it were stationary in the path of the beam. In addition, the time averaged thickness can be adjusted if the amplitude of the fiber motion is increased or decreased to obtain a thinner or thicker target respectively. Measurements that compare the lifetime of the stored beam in the presence of a fiber target with the lifetime of a stored beam in the presence of a gas target show that a fiber target of a certain time averaged target thickness is equivalent to a homogeneous target of the same thickness. The data are in good agreement with Monte Carlo calculations

The impact of a 50% reduction of solid waste disposal in Canada on methane emissions from landfills in 2000

International Nuclear Information System (INIS)

Patenaude, L.M.F.; Owen, G.T.; Barclay, J.A.

1993-01-01

Canada's Green Plan established a goal of 50% reduction in municipal solid waste (MSW) disposal between 1988 and the year 2000. Canada has also committed to stabilizing greenhouse gas emissions at 1990 levels by 2000. MSW landfills are targeted since they account for a significant portion of anthropogenic methane emissions. Current composition and quantities of MSW were estimated. Using five scenarios for achieving a 50% reduction of waste disposed, the quantities and composition of waste managed were estimated through to the year 2000. A first-order decay model was used to estimate methane emissions from landfills of each scenario by varying the methane generation potential (L o ) based on the amount of biodegradable carbon in the MSW stream. Despite the overall reduction in waste, methane emissions are still projected on increase between 1990 and 2000 for scenarios with 25 to 45% of waste going to landfill in 2000. The estimated increases in methane emissions range from 2% for the high composting scenario to 16% for the high landfill scenario. In general, emissions peak during the 1990's and are decreasing by 2000. The projected increase in emissions is due to the 65--75% contribution of MSW landfilled before 1990. In conclusion, a significant reduction in methane emissions from landfills by 2000 will require methane recovery systems in addition to MSW reduction initiatives

Secondary Electron Emission from Solid Hydrogen and Deuterium Resulting from Incidence of keV Electrons and Hydrogen Ions

DEFF Research Database (Denmark)

Sørensen, H.

1977-01-01

are small, in contrast to what is expected for insulating materials. One explanation is that the secondary electrons lose energy inside the target material by exciting vibrational and rotational states of the molecules, so that the number of electrons that may escape as secondary electrons is rather small....... The losses to molecular states will be largest for hydrogen, so that the SEE coefficients are smallest for solid hydrogen, as was observed. For the incidence of ions, the values of δ for the different molecular ions agree when the number of secondary electrons per incident atom is plotted versus the velocity...... or the stopping power of the incident particles. Measurements were also made for oblique incidence of H+ ions on solid deuterium for angles of incidence up to 75°. A correction could be made for the emission of secondary ions by also measuring the current calorimetrically. At largest energies, the angular...

Solid state cathodoluminescence and the properties of its two emission peaks

International Nuclear Information System (INIS)

Xu Xurong

2007-01-01

We discovered solid state cathodoluminescence (SSCL). For its identification we excluded all artifacts, carried out its cross proof and studied its generality. Its spectrum is characterized by the appearance of short wavelength peak when the applied voltage is increased. Three voltage ranges are distinguished, in the lower voltage range we have the long wavelength emission, in the middle range we have both long and short wavelength emissions, and in the higher voltage range we have only the short wavelength emission. The mechanism of this spectral shift lies in the electrical field ionization of excitons. This effect initiates the applicability of band model besides molecular excitons theory. The temporal behaviors of both peaks in SSCL are studied with a method of estimating lifetime by means of frequency dependence on intensity. The lifetime of short wavelength emission is found to be 5 ms and that of long wavelength emission is less than 0.05 ms

Emissions intensity targeting: From China's 12th Five Year Plan to its Copenhagen commitment

International Nuclear Information System (INIS)

Lu, Yingying; Stegman, Alison; Cai, Yiyong

2013-01-01

China is currently the world's largest single source of fossil fuel related CO 2 emissions. In response to pressure from the international community, and in recognition of its role in global climate change mitigation, the Chinese government has announced a series of climate policy commitments, in both the Copenhagen Accord and its domestic 12th 5 Year Plan, to gradually reduce emissions intensity by 2020. Emissions intensity reduction commitments differ significantly from emission level reduction commitments that are commonly adopted by developed economies. In this paper, we investigate the economic implications of China's recent commitments to reduce emissions intensity, and highlight the complexities involved in modelling intensity targets under uncertainty. Using G-Cubed, an intertemporal, computable general equilibrium model of the world economy, we show that China's emissions intensity targets could be achieved with a range of low and high growth emissions level trajectories corresponding to low and high growth GDP scenarios, which lead to different welfare consequences. - Highlights: • We investigate the economic implication of China's recent climate commitments. • We address the complexity of modelling reduction in emissions intensity. • The 2015 target gives China more flexibility towards its 2020 target. • The policy restriction is eased in high growth periods. • In low growth periods an intensity target places a further restriction on the economy

Applications of beam-foil spectroscopy to atomic collisions in solids

Science.gov (United States)

Sellin, I. A.

1976-01-01

Some selected papers presented at the Fourth International Conference on Beam-Foil Spectroscopy, whose results are of particular pertinence to ionic collision phenomena in solids, are reviewed. The topics discussed include solid target effects and means of surmounting them in the measurement of excited projectile ion lifetimes for low-energy heavy element ions; the electron emission accompanying the passage of heavy particles through solid targets; the collision broadening of X rays emitted from 100 keV ions moving in solids; residual K-shell excitation in chlorine ions penetrating carbon; comparison between 40 MeV Si on gaseous SiH4 targets at 300 mtorr and 40 MeV Si on Al; and the emergent surface interaction in beam-foil spectroscopy. A distinct overlap of interests between the sciences of beam-foil spectroscopy and atomic collisions in solids is pointed out.

Study of solid target preparation for developing I-124, Pd-103, Cu-64 radioisotopes based cyclotron

Energy Technology Data Exchange (ETDEWEB)

Kim, Jae Hong; Park, Hyun; Lee, Ji Sub; Lee, Dong Hoon; Chun, Kwon Soo [Korea Institute of Radiological and Medical Sciences, Seoul (Korea, Republic of); Choi, Hee Dong [Seoul National Univ., Seoul (Korea, Republic of)

2005-07-01

The decay characteristics of I-124, Pd-103 and Cu-64 radioisotopes produced by cyclotron have considered useful agents for diagnostic imaging or therapy. Numbers of radioisotopes used in medical applications or promised for development are produced with solid targets. The aims of developing solid targets are to obtain large quantities of radionuclides from accelerators. The scope of the study is to develop optimized target system and chemical procedures of these radioisotopes. In order to increase the availability of the radionuclides, the investigation for the design of the solid target and different procedures yielding efficient production of high specific activity will be carrying. In this work, we will present the issue of the primary target design concept.

City-specific vehicle emission control strategies to achieve stringent emission reduction targets in China's Yangtze River Delta region.

Science.gov (United States)

Zhang, Shaojun; Wu, Ye; Zhao, Bin; Wu, Xiaomeng; Shu, Jiawei; Hao, Jiming

2017-01-01

The Yangtze River Delta (YRD) region is one of the most prosperous and densely populated regions in China and is facing tremendous pressure to mitigate vehicle emissions and improve air quality. Our assessment has revealed that mitigating vehicle emissions of NOx would be more difficult than reducing the emissions of other major vehicular pollutants (e.g., CO, HC and PM 2.5 ) in the YRD region. Even in Shanghai, where the emission control implemented are more stringent than in Jiangsu and Zhejiang, we observed little to no reduction in NOx emissions from 2000 to 2010. Emission-reduction targets for HC, NOx and PM 2.5 are determined using a response surface modeling tool for better air quality. We design city-specific emission control strategies for three vehicle-populated cities in the YRD region: Shanghai and Nanjing and Wuxi in Jiangsu. Our results indicate that even if stringent emission control consisting of the Euro 6/VI standards, the limitation of vehicle population and usage, and the scrappage of older vehicles is applied, Nanjing and Wuxi will not be able to meet the NOx emissions target by 2020. Therefore, additional control measures are proposed for Nanjing and Wuxi to further mitigate NOx emissions from heavy-duty diesel vehicles. Copyright © 2016. Published by Elsevier B.V.

Environmental performance of the Kvaerner BFB boilers for MSW combustion -- Analysis of gaseous emissions and solid residues

International Nuclear Information System (INIS)

Lundberg, M.; Hagman, U.; Andersson, B.A.; Olofsson, J.

1997-01-01

Kvaerner Pulping AB (formerly Kvaerner EnviroPower AB) has, due to the stringent demands on emissions performance, developed a state-of-the-art bubbling fluidized bed boiler (BFB) designed for waste fuel firing with very low emissions to the air. A complete evaluation of the environmental performance of the Kvaerner BFB technique for MSW combustion is now possible thanks to a thorough characterization study of the solid residues from the Lidkoeping plant. This paper gives an overall mapping of the emissions performance. Data from the operating plants on solid residue characteristics and leachability, heavy metal and dioxin emissions, nitrogen oxides, carbon monoxide, acid gases, and other emissions to air are presented. Comparisons are made with legislative limits and data from the mass burning technique. It is concluded that the emissions are low compared both with data from traditional mass burn incinerators and with legislative limits in the USA and Europe. Furthermore, the bottom and cyclone ash characteristics are shown not to cause any particular problem from an environmental point of view, and that the leachability is well below the existing legislative limits in Europe and the USA. The results show that fluidized bed combustion of municipal solid waste is a very competitive alternative to the traditional mass burning technique in every respect

Production of solid deuterium targets by ion implantation

International Nuclear Information System (INIS)

Csikai, J.; Szegedi, S.; Olah, L.; El-Megrab, A.M.; Molla, N.I.; Rahman, M.M.; Miah, R.U.; Habbani, F.; Shaddad, I.

1997-01-01

Solid metal, semiconductor and metallic glass samples were irradiated with deuteron atomic ions between 60 and 180 keV incident energies. Accumulation rates of deuterons in different targets were recorded by the detection of protons and neutrons via the 2 H(d,p) and 2 H(d,n) reactions. A simple analytical expression is given to describe the kinetics of the accumulation. The dependence of the reaction rate on the deuteron energy gives information on the concentration profile in addition to the neutron flux density spectra. A varying distortion of the implanted deuteron profiles by a change in the beam energy were also observed for different targets. (orig.)

Emissions and targets of greenhouse gases not included in the Emission Trading System 2013-2020

Energy Technology Data Exchange (ETDEWEB)

Verdonk, M.

2011-06-15

This report evaluates the European Commission's (EC) proposal to calculate Member States' targets for emissions not included in the Emission Trading System (ETS) (as announced in the so-called Effort Sharing Decision). The calculation procedures and data sources proposed by the EC have been used for calculating non-ETS emission targets for the Netherlands, for the years from 2013 to 2020. In order to compare results, an alternative approach also was introduced and evaluated. In this approach more transparent data sources were used. Furthermore, the report updates the emission forecast of non-ETS emission levels in the Netherlands, for 2020, and evaluates the consequences of excluding uncertainties related to monitoring from the (updated) emission forecast. It is concluded that, for the Netherlands, the non-ETS emission caps as proposed by the EC would result in an emission cap of 105 Mt CO2 equivalent by 2020. This is higher than in the alternative approach, which would result in a cap of 103 Mt CO2 equivalents. The difference is explained by the different data sources that were used. A drawback of the data sources used in the EC proposal is the lack of transparency of part of the data, which resulted in an additional uncertainty as not all issues could be verified. However, other Member States may not have similar data sources available, in case the EC decides to adopt the alternative approach. The calculated emission caps are to be considered as estimates based on the most recent (but sometimes uncertain) statistics. The EC will determine the definite caps by the end of 2012. Based on a 2010 forecast, and including both an updated division of emissions into ETS and non-ETS emissions and a revised methodology for calculating nitrous oxide emissions, we estimate that non-ETS emissions in the Netherlands would be 104 Mt CO2 equivalents by 2020, with an uncertainty range of between 96 and 112 Mt CO2 equivalents. It is our conclusion that non-ETS emission

Modeling alignment enhancement for solid polarized targets

Energy Technology Data Exchange (ETDEWEB)

Keller, D. [University of Virginia, Charlottesville, VA (United States)

2017-07-15

A model of dynamic orientation using optimized radiofrequency (RF) irradiation produced perpendicular to the holding field is developed for the spin-1 system required for tensor-polarized fixed-target experiments. The derivation applies to RF produced close to the Larmor frequency of the nucleus and requires the electron spin-resonance linewidth to be much smaller than the nuclear magnetic resonance frequency. The rate equations are solved numerically to study a semi-saturated steady-state resulting from the two sources of irradiation: microwave from the DNP process and the additional RF used to manipulate the tensor polarization. The steady-state condition and continuous-wave NMR lineshape are found that optimize the spin-1 alignment in the polycrystalline materials used as solid polarized targets in charged-beam nuclear and particle physics experiments. (orig.)

An analysis of China's CO2 emission peaking target and pathways

Directory of Open Access Journals (Sweden)

Jian-Kun He

2014-12-01

Full Text Available China has set the goal for its CO2 emissions to peak around 2030, which is not only a strategic decision coordinating domestic sustainable development and global climate change mitigation but also an overarching target and a key point of action for China's resource conservation, environmental protection, shift in economic development patterns, and CO2 emission reduction to avoid climate change. The development stage where China maps out the CO2 emission peak target is earlier than that of the developed countries. It is a necessity that the non-fossil energy supplies be able to meet all the increased energy demand for achieving CO2 emission peaking. Given that China's potential GDP annual increasing rate will be more than 4%, and China's total energy demand will continue to increase by approximately 1.0%–1.5% annually around 2030, new and renewable energies will need to increase by 6%–8% annually to meet the desired CO2 emission peak. The share of new and renewable energies in China's total primary energy supply will be approximately 20% by 2030. At that time, the energy consumption elasticity will decrease to around 0.3, and the annual decrease in the rate of CO2 intensity will also be higher than 4% to ensure the sustained growth of GDP. To achieve the CO2 emission peaking target and substantially promote the low-carbon development transformation, China needs to actively promote an energy production and consumption revolution, the innovation of advanced energy technologies, the reform of the energy regulatory system and pricing mechanism, and especially the construction of a national carbon emission cap and trade system.

Ion-induced emission of charged particles from solid hydrogen and deuterium

International Nuclear Information System (INIS)

Borgesen, P.; Schou, J.; Sorensen, H.

1980-01-01

Measurements have been made of the emission of both positive and negative particles from solid hydrogen and deuterium for normal incidence of H + , H + 2 , H + 3 , D 2 H + , D + 3 and He + ions up to 10 keV. For positive particles the emission coefficient increased with increasing energy of incidence to reach a value of 0.08 per atom for 10 keV H + onto hydrogen. Apparently the positive particles are sputtered ones. The negative particles emitted are predominantly electrons. The emission coefficient per incident atom as a function of the velocity of the incident particle agress fairly well with results published earlier for incidence of hydrogen and deuterium ions. However, systematic differences of up to 10% are now observed between the coefficients for the different types of ions. (orig.)

Assessing Multiple Pathways for Achieving China’s National Emissions Reduction Target

Directory of Open Access Journals (Sweden)

Mingyue Wang

2018-06-01

Full Text Available In order to achieve China’s target of carbon intensity emissions reduction in 2030, there is a need to identify a scientific pathway and feasible strategies. In this study, we used stochastic frontier analysis method of energy efficiency, incorporating energy structure, economic structure, human capital, capital stock and potential energy efficiency to identify an efficient pathway for achieving emissions reduction target. We set up 96 scenarios including single factor scenarios and multi-factors combination scenarios for the simulation. The effects of each scenario on achieving the carbon intensity reduction target are then evaluated. It is found that: (1 Potential energy efficiency has the greatest contribution to the carbon intensity emissions reduction target; (2 they are unlikely to reach the 2030 carbon intensity reduction target of 60% by only optimizing a single factor; (3 in order to achieve the 2030 target, several aspects have to be adjusted: the fossil fuel ratio must be lower than 80%, and its average growth rate must be decreased by 2.2%; the service sector ratio in GDP must be higher than 58.3%, while the growth rate of non-service sectors must be lowered by 2.4%; and both human capital and capital stock must achieve and maintain a stable growth rate and a 1% increase annually in energy efficiency. Finally, the specific recommendations of this research were discussed, including constantly improved energy efficiency; the upgrading of China’s industrial structure must be accelerated; emissions reduction must be done at the root of energy sources; multi-level input mechanisms in overall levels of education and training to cultivate the human capital stock must be established; investment in emerging equipment and accelerate the closure of backward production capacity to accumulate capital stock.

Mercury emission to the atmosphere from municipal solid waste landfills: A brief review

Science.gov (United States)

Tao, Zhengkai; Dai, Shijin; Chai, Xiaoli

2017-12-01

Municipal solid waste (MSW) landfill is regarded as an important emission source of atmospheric mercury (Hg), which is associated with potential health and environmental risks, as outlined by the Minamata Convention on Hg. This review presents the current state of knowledge with regards to landfill Hg sources, Hg levels in MSW and cover soils, Hg emission to the atmosphere, available Hg biogeochemical transformations, research methods for Hg emission, and important areas for future research. In addition, strategies for controlling landfill Hg emissions are considered, including reducing the Hg load in landfill and in situ controls. These approaches mainly focus on Hg source reduction, Hg recycling programs, public education, and in situ technology such as timely soil cover, vegetation, and end-of-pipe technology for controlling Hg emission from landfill gas.

Preparing a suitable solid target for generating copper-64 using a biomedical cyclotron

International Nuclear Information System (INIS)

Jeffery, Charmaine; Cryer, David; Chan, Sun; Asad, Ali; Fleming, Adam; Hubble, Lee

2009-01-01

Full text: Radiopharmaceutical research at SCGH has been advancing in the production of copper-64, a promising radionuclide for PET. Production has commenced using a self-manufactured solid target with alBA 18/9 cyclotron, via the 6 4 N i(p,n) 6 4 C u reaction pathway. One aspect of the project has been the preparation of a suitable solid target for irradiation. The chosen production method involves electrolysis of a solution of nickel ammonium sulphate in a self-manufactured electroplating cell, using a gold disk as the cathode for deposition of nickel metal. Various defects in the nickel surface were observed ∼ including cracks, formation of pits and inclusions, loose powder-like plating, lack of metallic lustre and lifting of the plated nickel. Several variables were investigated - including adjustment of the anode-cathode distance, anode composition, solution composition, and voltage/current settings. A suitable method that produced acceptable plating was achieved - the surface was then analysed to ensure there were no underlying defects. Three analytical techniques were used - AFM, SEM and optical profilometry. Two disks were ana lysed (approx. 3 0 m g of natNi plated). The depth of plating, evenness of plating and surface uniformity were of particular interest. Conclusions: Analysis revealed that the surface was not completely uniform (thinner at edges, 'well' in centre, with inclusions on the surface more prevalent than pitting), and required more nickel to be plated to reach optimum thickness. Final target specifications are still being optimised, however test irradiation of a solid target ( 3 1 n ickel, I l0 m g) proved that a sound solid target can be reliably produced and irradiated.

Optical emission from Al target irradiated by FLASH

International Nuclear Information System (INIS)

Stránský, M; Rohlena, K

2014-01-01

The following text touches on some peculiarities in optical emission spectroscopy results from experiments on the free-electron laser FLASH [1, 2]. Aluminum targets were irradiated with 13.5 nm ∼ 25 fs pulses at intensities of 10 13 and 10 16 W/cm 2 (20 and 1 μm foci). Surprisingly, only neutral atom lines for the case with wider focus and traces of ion lines in the tighter focus case were observed with the optical emission spectroscopy (200–600 nm range), [2]. The motivating idea behind this work is the suggestion in [1] by Zastrau that the optical spectrometer sees only emissions from a cold expanding lower-density (< 10 22 cm −3 ) plasma plume. In this contribution the notion of UV range screening is analyzed in detail.

Internal combustion engine run on biogas is a potential solution to meet Indonesia emission target

Science.gov (United States)

Ambarita, Himsar

2017-09-01

Indonesia has released two different Greenhouse Gas (GHG) emissions reduction targets. The first target, released in 2009, is reduction GHG emissions 26% from Business-as-Usual (BAU) level using own budget and up 41% if supported international aids by 2020. The second target is reduction 29% and 41% from BAU by 2030 using own budget and with international support, respectively. In this paper, the BAU emissions and emissions reduction target of these two targets are elaborated. In addition, the characteristics of emissions from transportation sector are discussed. One of the potential mitigation actions is switching fuel in transportation sector. The results the most promising mitigation action in the transportation is switching oil fuel with biofuel. The Government of Indonesia (GoI) focuses on using biodiesel and bioethanol to run internal combustion engine in transportation sector and biogas is aimed to fuel power plant unit. However, there is very limited of success stories on using biogas in the power plant. The barriers and challenges will be discussed here. It is suggested to run internal combustion engine with biogas.

Analysing the emission gap between pledged emission reductions under the Cancun Agreements and the 2C climate target

Energy Technology Data Exchange (ETDEWEB)

Den Elzen, M. G.J.; Roelfsema, M.; Hof, A. F. [Netherlands Environmental Assessment Agency PBL, Den Haag (Netherlands); Boettcher, H. [Institute for Applied Systems Analysis IIASA, Laxenburg (Austria); Grassi, G. [Joint Research Centre JRC, European Commission, Ispra (Italy)

2012-04-15

In the Cancun Agreements, Annex I Parties (industrialised countries) and non-Annex I Parties (developing countries) made voluntary pledges to reduce greenhouse gas emissions by 2020. The Cancun Agreements also state a long-term target of limiting temperature increase to a maximum of 2C above pre-industrial levels. This report is an update of the PBL report 'Evaluation of the Copenhagen Accord', which similar to earlier studies showed that there is a possible gap in emissions between the emission level resulting from the pledges and the level necessary to achieve the 2C target. The updates involve new information on many topics that have become available over the last two years, including updated national business-as-usual emission projections as provided by the countries themselves, and more information on uncertainties and on factors influencing the size of the emission gap. In this context, the main objective of this report can be formulated as follows: This report analyses the effect of the pledges put forward by the Parties in the Cancun Agreements on the emission gap, taking into account all the new information available. It pays specific attention to uncertainties and risks and describes in more detail the emission implications of the pledges and actions of the 12 largest emitting countries or regions.

Analysing the emission gap between pledged emission reductions under the Cancun Agreements and the 2C climate target

Energy Technology Data Exchange (ETDEWEB)

Den Elzen, M.G.J.; Roelfsema, M.; Hof, A.F. [Netherlands Environmental Assessment Agency PBL, Den Haag (Netherlands); Boettcher, H. [Institute for Applied Systems Analysis IIASA, Laxenburg (Austria); Grassi, G. [Joint Research Centre JRC, European Commission, Ispra (Italy)

2012-04-15

In the Cancun Agreements, Annex I Parties (industrialised countries) and non-Annex I Parties (developing countries) made voluntary pledges to reduce greenhouse gas emissions by 2020. The Cancun Agreements also state a long-term target of limiting temperature increase to a maximum of 2C above pre-industrial levels. This report is an update of the PBL report 'Evaluation of the Copenhagen Accord', which similar to earlier studies showed that there is a possible gap in emissions between the emission level resulting from the pledges and the level necessary to achieve the 2C target. The updates involve new information on many topics that have become available over the last two years, including updated national business-as-usual emission projections as provided by the countries themselves, and more information on uncertainties and on factors influencing the size of the emission gap. In this context, the main objective of this report can be formulated as follows: This report analyses the effect of the pledges put forward by the Parties in the Cancun Agreements on the emission gap, taking into account all the new information available. It pays specific attention to uncertainties and risks and describes in more detail the emission implications of the pledges and actions of the 12 largest emitting countries or regions.

Solid expandable systems put deepwater targets within reach

Energy Technology Data Exchange (ETDEWEB)

Perez-Roca, Eduardo [Enventure Global Technology L.L.C., Houston, TX (United States). Latin America; Fristch, Jerry [Enventure Global Technology L.L.C., Houston, TX (United States)

2008-07-01

Enabling technologies that take drilling operations to deeper objectives have made a significant impact on the practicality of many projects, especially deep water offshore targets. Increasing vertical depth and lateral reach requires adequate hole size to attain the desired objectives of the well bore. Solid expandable technology can maintain and retain hole size to address both the physical limitations and the economic feasibility of deep water operations. With each and every casing point, the potential for adequate hole size at total depth (TD) decreases. Solid expandable open hole liners and single-diameter systems reduce and eliminate, respectively, the well bore tapering that dictates hole size at TD and subsequent completion size. Successful mitigation of this tapering, whether through the entire well bore or through select zones, enables operators to gain access to previously unreachable reserves. Solid expandable systems have proven to be reliable and effective with over 1,000 installations in a myriad of conditions and environments worldwide. To date, over 115 of those applications have been in deep water environments. The current operating envelope for solid expandable systems include the deepest installation at {approx}28,750 ft (8,763 m) and the longest at 6,867 ft (2,083 m) in water depth over 3,150 ft (960 m). This record-length application consisted of an open hole liner installed and expanded in a single run. This paper will discuss the effectiveness of solid expandable systems in deep water operations and how the technology brings value to offshore projects especially when planned into the initial design. Case histories will be used to further illustrate the features, advantages, and benefits of expandable technology. In addition, this paper will examine the state of the solid expandable technology and its continuing evolution to provide even more drilling solutions. (author)

Assessment of alternative disposal methods to reduce greenhouse gas emissions from municipal solid waste in India.

Science.gov (United States)

Yedla, Sudhakar; Sindhu, N T

2016-06-01

Open dumping, the most commonly practiced method of solid waste disposal in Indian cities, creates serious environment and economic challenges, and also contributes significantly to greenhouse gas emissions. The present article attempts to analyse and identify economically effective ways to reduce greenhouse gas emissions from municipal solid waste. The article looks at the selection of appropriate methods for the control of methane emissions. Multivariate functional models are presented, based on theoretical considerations as well as the field measurements to forecast the greenhouse gas mitigation potential for all the methodologies under consideration. Economic feasibility is tested by calculating the unit cost of waste disposal for the respective disposal process. The purpose-built landfill system proposed by Yedla and Parikh has shown promise in controlling greenhouse gas and saving land. However, these studies show that aerobic composting offers the optimal method, both in terms of controlling greenhouse gas emissions and reducing costs, mainly by requiring less land than other methods. © The Author(s) 2016.

[Preparation, quality control and thyroid molecule imaging of solid-target based radionuclide ioine-124].

Science.gov (United States)

Zhu, H; Wang, F; Guo, X Y; Li, L Q; Duan, D B; Liu, Z B; Yang, Z

2018-04-18

To provide useful information for the further production and application of this novel radio-nuclide for potential clinical application. 124 Te (p,n) 124 I nuclide reaction was used for the 124 I production. Firstly, the target material, 124 TeO 2 (200 mg) and Al2O3 (30 mg) mixture, were compressed into the round platinum based solid target by tablet device. HM-20 medical cyclotron was applied to irradiate the solid target slice for 6-10 h with helium and water cooling. Then, the radiated solid target was placed for 12 h (overnight) to decay the radioactive impurity; finally, 124 I was be purified by dry distillation using 1 mL/min nitrogen for about 6 hours and radiochemical separation methods. Micro-PET imaging studies were performed to investigate the metabolism properties and thyroid imaging ability of 124 I.After 740 kBq 124 I was injected intravenously into the tail vein of the normal mice, the animals were imaged with micro-PET and infused with CT. The micro-PET/CT infusion imaging revealed actual state 124 I's metabolism in the mice. It was been successfully applied for 200 mg 124 TeO 2 plating by the tablet device on the surface of platinum. It showed smooth, dense surface and without obviously pits and cracks. The enriched 124 Te target was irradiated for 6 to 10 hours at about 12.0 MeV with 20 μA current on HM-20 cyclotron. Then 370-1 110 MBq 124 I could be produced on the solid target after irradiation and 370-740 MBq high specific activity could be collected afterdry distillation separation and radio-chemical purification. 124 I product was finally dissolved in 0.01 mol/L NaOH for the future distribution. The gamma spectrum of the produced 124 I-solution showed that radionuclide purity was over 80.0%. The micro-PET imaging of 124 I in the normal mice exhibited the thyroid and stomach accumulations and kidney metabolism, the bladder could also be clearly visible, which was in accordance with what was previously reported. To the best of our knowledge

Reducing emissions from agriculture to meet the 2 °C target

DEFF Research Database (Denmark)

Wollenberg, Eva; Richards, Meryl; Smith, Pete

2016-01-01

identify a preliminary global target for reducing emissions from agriculture of ~1 GtCO2e yr−1 by 2030 to limit warming in 2100 to 2 °C above pre-industrial levels. Yet plausible agricultural development pathways with mitigation cobenefits deliver only 21–40% of needed mitigation. The target indicates...... that more transformative technical and policy options will be needed, such as methane inhibitors and finance for new practices. A more comprehensive target for the 2 °C limit should be developed to include soil carbon and agriculture-related mitigation options. Excluding agricultural emissions from......More than 100 countries pledged to reduce agricultural greenhouse gas (GHG) emissions in the 2015 Paris Agreement of the United Nations Framework Convention on Climate Change. Yet technical information about how much mitigation is needed in the sector vs. how much is feasible remains poor. We...

Solid Particle Number Emission Factors of Euro VI Heavy-Duty Vehicles on the Road and in the Laboratory

Science.gov (United States)

Giechaskiel, Barouch

2018-01-01

Particulate matter (PM), and in particular ultrafine particles, have a negative impact on human health. The contribution of vehicle PM emissions to air pollution is typically quantified with emission inventories, which need vehicle emission factors as input. Heavy-duty vehicles, although they represent a small percentage of the vehicle population in nearly every major country, contribute the majority of the on-road PM emissions. However, the published data of modern heavy-duty vehicle emissions are scarce, and for the newest Euro VI technologies, almost non-existent. The main objective of this paper is to present Solid Particle Number (SPN) emission factors from Euro VI heavy-duty vehicles using diesel, Compressed Natural Gas (CNG), or Liquefied Natural Gas (LNG). Urban, rural and motorway (highway) emissions were determined on the road at various European cities using SPN Portable Emission Measurement Systems (PEMS). Additional tests on a heavy-duty chassis dynamometer showed that the solid sub-23 nm fraction, which is not covered at the moment in the European regulation, is high, especially for CNG engines. The significant contribution of regeneration events and the effect of ambient temperature and engine cold-start on particle emissions were also discussed. PMID:29425174

Solid Particle Number Emission Factors of Euro VI Heavy-Duty Vehicles on the Road and in the Laboratory

Directory of Open Access Journals (Sweden)

Barouch Giechaskiel

2018-02-01

Full Text Available Particulate matter (PM, and in particular ultrafine particles, have a negative impact on human health. The contribution of vehicle PM emissions to air pollution is typically quantified with emission inventories, which need vehicle emission factors as input. Heavy-duty vehicles, although they represent a small percentage of the vehicle population in nearly every major country, contribute the majority of the on-road PM emissions. However, the published data of modern heavy-duty vehicle emissions are scarce, and for the newest Euro VI technologies, almost non-existent. The main objective of this paper is to present Solid Particle Number (SPN emission factors from Euro VI heavy-duty vehicles using diesel, Compressed Natural Gas (CNG, or Liquefied Natural Gas (LNG. Urban, rural and motorway (highway emissions were determined on the road at various European cities using SPN Portable Emission Measurement Systems (PEMS. Additional tests on a heavy-duty chassis dynamometer showed that the solid sub-23 nm fraction, which is not covered at the moment in the European regulation, is high, especially for CNG engines. The significant contribution of regeneration events and the effect of ambient temperature and engine cold-start on particle emissions were also discussed.

Solid Particle Number Emission Factors of Euro VI Heavy-Duty Vehicles on the Road and in the Laboratory.

Science.gov (United States)

Giechaskiel, Barouch

2018-02-09

Particulate matter (PM), and in particular ultrafine particles, have a negative impact on human health. The contribution of vehicle PM emissions to air pollution is typically quantified with emission inventories, which need vehicle emission factors as input. Heavy-duty vehicles, although they represent a small percentage of the vehicle population in nearly every major country, contribute the majority of the on-road PM emissions. However, the published data of modern heavy-duty vehicle emissions are scarce, and for the newest Euro VI technologies, almost non-existent. The main objective of this paper is to present Solid Particle Number (SPN) emission factors from Euro VI heavy-duty vehicles using diesel, Compressed Natural Gas (CNG), or Liquefied Natural Gas (LNG). Urban, rural and motorway (highway) emissions were determined on the road at various European cities using SPN Portable Emission Measurement Systems (PEMS). Additional tests on a heavy-duty chassis dynamometer showed that the solid sub-23 nm fraction, which is not covered at the moment in the European regulation, is high, especially for CNG engines. The significant contribution of regeneration events and the effect of ambient temperature and engine cold-start on particle emissions were also discussed.

Emission of volatile sulfur compounds during composting of municipal solid waste (MSW)

International Nuclear Information System (INIS)

Zhang, Hongyu; Schuchardt, Frank; Li, Guoxue; Yang, Jinbing; Yang, Qingyuan

2013-01-01

Highlights: ► We compare the volatile sulfur compounds (VSCs) emissions during three types of municipal solid wastes (MSWs) composting. ► The VSCs released from the kitchen waste composting was significantly higher than that from 15–80 mm fraction of MSW. ► Among the five VSCs, H 2 S was the most abundant compound with 39.0–43.0% of total VSCs released. ► Addition of 20% cornstalks could significantly reduce the VSCs emissions during kitchen waste composting. - Abstract: Volatile sulfur compounds (VSCs) are the main source for malodor from composting plants. In this study, the VSCs generated from composting of 15–80 mm municipal solid waste (T0), kitchen waste (T1) and kitchen waste mixed dry cornstalks (T2) were measured in 60 L reactors with forced aeration for a period of 30 days. The VSCs detected in all treatments were hydrogen sulfide (H 2 S), methyl mercaptan (MM), dimethyl sulfide (DMS), carbon bisulfide (CS 2 ) and dimethyl disulfide (DMDS). Over 90% of the VSCs emissions occurred during the first 15 days, and reached their peak values at days 4–7. The emission profiles of five VSCs species were significantly correlated with internal materials temperature and outlet O 2 concentration (p −1 (dry matter) for T0, T1 and T2, respectively. Among the five VSCs, H 2 S was the most abundant compound with 39.0–43.0% of total VSCs released. Composting of kitchen waste from separate collection posed a negative influence on the VSC and leachate production because of its high moisture content. An addition of dry cornstalks at a mixing ratio of 4:1 (wet weight) could significantly reduce the VSCs emissions and avoid leachate. Compared to pure kitchen waste, VSCs were reduced 66.8%

Broadly tunable metal halide perovskites for solid-state light-emission applications

OpenAIRE

Adjokatse, Sampson; Fang, Hong-Hua; Loi, Maria Antonietta

2017-01-01

The past two years have witnessed heightened interest in metal-halide perovskites as promising optoelectronic materials for solid-state light emitting applications beyond photovoltaics. Metal-halide perovskites are low-cost solution-processable materials with excellent intrinsic properties such as broad tunability of bandgap, defect tolerance, high photoluminescence quantum efficiency and high emission color purity (narrow full-width at half maximum). In this review, the photophysical propert...

Solid hydrogen target for laser driven proton acceleration

Science.gov (United States)

Perin, J. P.; Garcia, S.; Chatain, D.; Margarone, D.

2015-05-01

The development of very high power lasers opens up new horizons in various fields, such as laser plasma acceleration in Physics and innovative approaches for proton therapy in Medicine. Laser driven proton acceleration is commonly based on the so-called Target Normal Sheath Acceleration (TNSA) mechanisms: a high power laser is focused onto a solid target (thin metallic or plastic foil) and interact with matter at very high intensity, thus generating a plasma; as a consequence "hot" electrons are produced and move into the forward direction through the target. Protons are generated at the target rear side, electrons try to escape from the target and an ultra-strong quasi-electrostatic field (~1TV/m) is generated. Such a field can accelerate protons with a wide energy spectrum (1-200 MeV) in a few tens of micrometers. The proton beam characteristics depend on the laser parameters and on the target geometry and nature. This technique has been validated experimentally in several high power laser facilities by accelerating protons coming from hydrogenated contaminant (mainly water) at the rear of metallic target, however, several research groups are investigating the possibility to perform experiments by using "pure" hydrogen targets. In this context, the low temperature laboratory at CEA-Grenoble has developed a cryostat able to continuously produce a thin hydrogen ribbon (from 40 to 100 microns thick). A new extrusion concept, without any moving part has been carried out, using only the thermodynamic properties of the fluid. First results and perspectives are presented in this paper.

Enhanced electron emission from coated metal targets: Effect of surface thickness on performance

Directory of Open Access Journals (Sweden)

Saibabu Madas

2018-03-01

Full Text Available In this work, we establish an analytical formalism to address the temperature dependent electron emission from a metallic target with thin coating, operating at a finite temperature. Taking into account three dimensional parabolic energy dispersion for the target (base material and suitable thickness dependent energy dispersion for the coating layer, Fermi Dirac statistics of electron energy distribution and Fowler’s mechanism of the electron emission, we discuss the dependence of the emission flux on the physical properties such as the Fermi level, work function, thickness of the coating material, and operating temperature. Our systematic estimation of how the thickness of coating affects the emission current demonstrates superior emission characteristics for thin coating layer at high temperature (above 1000 K, whereas in low temperature regime, a better response is expected from thicker coating layer. This underlying fundamental behavior appears to be essentially identical for all configurations when work function of the coating layer is lower than that of the bulk target work function. The analysis and predictions could be useful in designing new coated materials with suitable thickness for applications in the field of thin film devices and field emitters.

Enhanced electron emission from coated metal targets: Effect of surface thickness on performance

Science.gov (United States)

Madas, Saibabu; Mishra, S. K.; Upadhyay Kahaly, Mousumi

2018-03-01

In this work, we establish an analytical formalism to address the temperature dependent electron emission from a metallic target with thin coating, operating at a finite temperature. Taking into account three dimensional parabolic energy dispersion for the target (base) material and suitable thickness dependent energy dispersion for the coating layer, Fermi Dirac statistics of electron energy distribution and Fowler's mechanism of the electron emission, we discuss the dependence of the emission flux on the physical properties such as the Fermi level, work function, thickness of the coating material, and operating temperature. Our systematic estimation of how the thickness of coating affects the emission current demonstrates superior emission characteristics for thin coating layer at high temperature (above 1000 K), whereas in low temperature regime, a better response is expected from thicker coating layer. This underlying fundamental behavior appears to be essentially identical for all configurations when work function of the coating layer is lower than that of the bulk target work function. The analysis and predictions could be useful in designing new coated materials with suitable thickness for applications in the field of thin film devices and field emitters.

Emission of volatile sulfur compounds during composting of municipal solid waste (MSW)

Energy Technology Data Exchange (ETDEWEB)

Zhang, Hongyu [Beijing Building Materials Academy of Science Research/State Key Laboratory of Solid Waste Reuse for Building Material, Beijing 100041 (China); College of Resources and Environment Sciences, China Agricultural University, Beijing 100094 (China); Schuchardt, Frank [Johann Heinrich von Thuenen-Institute, Institute of Agricultural Technology and Biosystems Engineering, Bundesallee 50, 38116 Braunschweig (Germany); Li, Guoxue, E-mail: ligx@cau.edu.cn [College of Resources and Environment Sciences, China Agricultural University, Beijing 100094 (China); Yang, Jinbing; Yang, Qingyuan [College of Resources and Environment Sciences, China Agricultural University, Beijing 100094 (China)

2013-04-15

Highlights: ► We compare the volatile sulfur compounds (VSCs) emissions during three types of municipal solid wastes (MSWs) composting. ► The VSCs released from the kitchen waste composting was significantly higher than that from 15–80 mm fraction of MSW. ► Among the five VSCs, H{sub 2}S was the most abundant compound with 39.0–43.0% of total VSCs released. ► Addition of 20% cornstalks could significantly reduce the VSCs emissions during kitchen waste composting. - Abstract: Volatile sulfur compounds (VSCs) are the main source for malodor from composting plants. In this study, the VSCs generated from composting of 15–80 mm municipal solid waste (T0), kitchen waste (T1) and kitchen waste mixed dry cornstalks (T2) were measured in 60 L reactors with forced aeration for a period of 30 days. The VSCs detected in all treatments were hydrogen sulfide (H{sub 2}S), methyl mercaptan (MM), dimethyl sulfide (DMS), carbon bisulfide (CS{sub 2}) and dimethyl disulfide (DMDS). Over 90% of the VSCs emissions occurred during the first 15 days, and reached their peak values at days 4–7. The emission profiles of five VSCs species were significantly correlated with internal materials temperature and outlet O{sub 2} concentration (p < 0.05). Total emissions of the VSCs were 216.1, 379.3 and 126.0 mg kg{sup −1} (dry matter) for T0, T1 and T2, respectively. Among the five VSCs, H{sub 2}S was the most abundant compound with 39.0–43.0% of total VSCs released. Composting of kitchen waste from separate collection posed a negative influence on the VSC and leachate production because of its high moisture content. An addition of dry cornstalks at a mixing ratio of 4:1 (wet weight) could significantly reduce the VSCs emissions and avoid leachate. Compared to pure kitchen waste, VSCs were reduced 66.8%.

Estimation of product specific emissions from municipal solid waste landfills for the inventory phase in LCA

DEFF Research Database (Denmark)

Nielsen, Per Henning; Hauschild, Michael Zwicky

1998-01-01

is frequently given as a quantity of solid wasteand possibly some recovered energy from waste incineration.Since product specific emissions can not be calculated or measured directly at the landfills, they must be estimated by modeling oflandfill processes. This paper presents a landfill model based on a large......), and inorganic non-metals (e.g. chlorine,) which are considered individually. The computer toolLCA-LAND is useful for estimation of emissions from specific waste products disposed in municipal solid waste landfills in Europeancountries (for the present Denmark, Germany and The Netherlands). Input data...... of materials and components and the manufacture, transportation and use of the product to thefinal disposal and possible recycling of the product. Although LCA has developed significantly during recent years, product specific emissions from disposed waste have only got minorattention in the literature leaving...

Global climate impacts of country-level primary carbonaceous aerosol from solid-fuel cookstove emissions

International Nuclear Information System (INIS)

Lacey, Forrest; Henze, Daven

2015-01-01

Cookstove use is globally one of the largest unregulated anthropogenic sources of primary carbonaceous aerosol. While reducing cookstove emissions through national-scale mitigation efforts has clear benefits for improving indoor and ambient air quality, and significant climate benefits from reduced green-house gas emissions, climate impacts associated with reductions to co-emitted black (BC) and organic carbonaceous aerosol are not well characterized. Here we attribute direct, indirect, semi-direct, and snow/ice albedo radiative forcing (RF) and associated global surface temperature changes to national-scale carbonaceous aerosol cookstove emissions. These results are made possible through the use of adjoint sensitivity modeling to relate direct RF and BC deposition to emissions. Semi- and indirect effects are included via global scaling factors, and bounds on these estimates are drawn from current literature ranges for aerosol RF along with a range of solid fuel emissions characterizations. Absolute regional temperature potentials are used to estimate global surface temperature changes. Bounds are placed on these estimates, drawing from current literature ranges for aerosol RF along with a range of solid fuel emissions characterizations. We estimate a range of 0.16 K warming to 0.28 K cooling with a central estimate of 0.06 K cooling from the removal of cookstove aerosol emissions. At the national emissions scale, countries’ impacts on global climate range from net warming (e.g., Mexico and Brazil) to net cooling, although the range of estimated impacts for all countries span zero given uncertainties in RF estimates and fuel characterization. We identify similarities and differences in the sets of countries with the highest emissions and largest cookstove temperature impacts (China, India, Nigeria, Pakistan, Bangladesh and Nepal), those with the largest temperature impact per carbon emitted (Kazakhstan, Estonia, and Mongolia), and those that would provide the

Global climate impacts of country-level primary carbonaceous aerosol from solid-fuel cookstove emissions

Science.gov (United States)

Lacey, Forrest; Henze, Daven

2015-11-01

Cookstove use is globally one of the largest unregulated anthropogenic sources of primary carbonaceous aerosol. While reducing cookstove emissions through national-scale mitigation efforts has clear benefits for improving indoor and ambient air quality, and significant climate benefits from reduced green-house gas emissions, climate impacts associated with reductions to co-emitted black (BC) and organic carbonaceous aerosol are not well characterized. Here we attribute direct, indirect, semi-direct, and snow/ice albedo radiative forcing (RF) and associated global surface temperature changes to national-scale carbonaceous aerosol cookstove emissions. These results are made possible through the use of adjoint sensitivity modeling to relate direct RF and BC deposition to emissions. Semi- and indirect effects are included via global scaling factors, and bounds on these estimates are drawn from current literature ranges for aerosol RF along with a range of solid fuel emissions characterizations. Absolute regional temperature potentials are used to estimate global surface temperature changes. Bounds are placed on these estimates, drawing from current literature ranges for aerosol RF along with a range of solid fuel emissions characterizations. We estimate a range of 0.16 K warming to 0.28 K cooling with a central estimate of 0.06 K cooling from the removal of cookstove aerosol emissions. At the national emissions scale, countries’ impacts on global climate range from net warming (e.g., Mexico and Brazil) to net cooling, although the range of estimated impacts for all countries span zero given uncertainties in RF estimates and fuel characterization. We identify similarities and differences in the sets of countries with the highest emissions and largest cookstove temperature impacts (China, India, Nigeria, Pakistan, Bangladesh and Nepal), those with the largest temperature impact per carbon emitted (Kazakhstan, Estonia, and Mongolia), and those that would provide the

Greenhouse gas emission trends and projections in Europe 2011. Tracking progress towards Kyoto and 2020 targets

Energy Technology Data Exchange (ETDEWEB)

Busche, J.; Scheffler, M.; Graichen, V. (Umweltbundesamt, Vienna (Austria)) (and others)

2011-10-15

At the end of 2010, the EU-15 was on track to achieve its Kyoto target but three EU-15 Member States (Austria, Italy and Luxembourg) were not on track to meet their burden-sharing targets. These countries must therefore seriously consider further action to ensure compliance, in particular revising their plans on using flexible mechanisms. Among the EEA member countries outside the EU, Liechtenstein and Switzerland were not on track to achieve their Kyoto target at the end of 2009. All other European countries are on track to meet their targets, either based on domestic emissions only or with the assistance of Kyoto mechanisms. The economic recession had a significant impact on the EU's total greenhouse gas (GHG) emission trends but a more limited effect on progress towards Kyoto targets. This is because emissions in the sectors covered by the EU Emissions Trading Scheme (ETS), which were most affected by the crisis, do not affect Kyoto compliance once ETS caps have been set. With existing national measures, Member States do not project enough emission reductions for the EU to meet its unilateral 20 % reduction commitment in 2020. Additional measures currently planned by Member States will help further reduce emissions but will be insufficient to achieve the important emission cuts needed in the longer term. By 2020 Member States must enhance their efforts to reduce emissions in non-EU ETS sectors, such as the residential, transport or agriculture sectors, where legally binding national targets have been set under the EU's 2009 climate and energy package. (Author)

THE EMISSION POTENTIAL FROM MUNICIPAL SOLID WASTE LANDFILL IN JORDAN

Directory of Open Access Journals (Sweden)

Mohammad Aljaradin

2016-01-01

Full Text Available A comprehensive study was conducted to monitor the emission potential from solid waste landfilled in Jordan over a period of 292 days using an anaerobic lysimeter. A 30 kg waste sample reflecting the typical municipal solid waste (MSW streams generated in Jordan was used to simulate the influence of climate on the emission potential of landfills located in semi-arid areas. The experimental results demonstrated that a significant amount of leachate and landfill gas was produced. The methane content was found to be more than 45% and the leachate produced reached 15.7 l after 200 days. However, after 260 days the gas and leachate production rate became negligible. A significant amount of heavy metal traces was found in the leachate due to mixed waste disposal. Changes in biogas and leachate quality parameters in the lysimeter revealed typical landfill behaviour trends, the only difference being that they developed much more quickly. In view of current landfill practices in Jordan and the effect of climate change, the results suggest that landfill design and operational modes need to be adjusted in order to achieve sustainability. For this reason, optimized design parameters and operational scenarios for sustainable landfill based on the country’s climatic conditions and financial as well as technical potential are recommended as a primary reference for future landfills in Jordan as well as in similar regions and climates.

Tritium solid targets for intense D-T neutron production and its related problems

International Nuclear Information System (INIS)

Sumita, Kenji

1988-01-01

This review paper is divided into three parts. Firstly, to attain an intense neutron production rate, the construction of a design with a higher tritium-containing surface and an effective cooling system like a rotating target device are discussed. The maximum attainable intensity based on tritium solid targets shall be estimated regarding planning for future D-T sources. Secondly, on the way to carry out some experiments, an absolute intensity calibration and an angular dependent neutron energy spectrum of the neutron source are essential parameters to analyse the results of the experiments. Sometimes the space dependent neutron spectrum is required as well as the space dependent neutron flux near the targets and irradiation samples. The measurement methods and their examples are reviewed for tritium solid targets. The third part is devoted to discuss the protection to tritium contamination problems due to unavoidable release of tritium gas from targets. Performance and effectiveness of tritium collection systems for intense D-T neutron sources shall be discussed in some examples. Tritium contamination incidents due to the faulted film powder of target surface are also reported in some real incident cases. (author). Abstract only

Copper K-shell emission cross sections for laser–solid experiments

Energy Technology Data Exchange (ETDEWEB)

Davies, J. R.; Betti, R.; Nilson, P. M.; Solodov, A. A. [Fusion Science Center for Extreme States of Matter, Laboratory for Laser Energetics, University of Rochester, Rochester, New York 14623 (United States)

2013-08-15

Published measurements and models of the cross section for electrons causing K-shell emission from copper are reviewed to find a suitable expression to use when analyzing K{sub α}-emission measurements in laser–solid experiments at peak intensities above 10{sup 18} W/cm{sup 2}. Few measurements exist in the 0.1- to 10-MeV electron energy range currently of interest, leaving a number of possible suitable models that are summarized here with a number of typing errors corrected. Two different limiting forms for the cross section at relativistic energies are used, and existing measurements do not give a clear indication as to which is correct. Comparison with the limiting form of electron stopping power indicates an alternative relativistic form and also that the density-effect correction will be important in copper above 10 MeV. For data analysis relying on relative K{sub α} emission caused by electrons with energy much greater than the K-shell binding energy, the existing uncertainty in cross sections is unimportant, but it will be a source of uncertainty when using absolute values and for electron energies up to ∼6× the binding energy. K-shell emission caused by photons and protons is also briefly reviewed.

Monitoring and Inventory of Hazardous Pollutants Emissions from Solid Waste Open Burning

Science.gov (United States)

KIM Oanh, N. T.

2017-12-01

Open burning remains a way to dispose of solid waste in developing countries, commonly practiced in places where municipal solid waste (MSW) management is not sufficiently efficient. This open burning practice emits huge amounts of toxic air pollutants, including semi-VOC of dioxins (PCDD/F) and polycyclic aromatic hydrocarbons (PAHs), particulate matters (PM), and toxic gases. This study measured toxic substances released from simulated open burning experiments of MSW (5 batches) and plastic waste (3 batches) to determine emission factors (EFs). Carbon content of the waste before and after burning was measured and the EFs were calculated using the carbon balance method. The obtained EFs of CO; CO2; NO2 and SO2 were 102±61; 1,684±96; 0.69±0.54; and 1.44±1.18 g/kg of dry MSW. The corresponding values for plastic waste were 13.0±6.0; 1,824±10; 0.12±0.07; and 0.14±0.09 g/kg, respectively. The EF of coarse PM (PM10-2.5); PM2.5 and BC in PM2.5 were, respectively, 6.1±5.6; 6.4±5.1 and 1.1±0.7 g/kg of MSW, and 2.3±0.1; 2.5±0.3; and 0.2±0.2 g/kg of plastic waste. The EFs of 17 dioxins and 16 PAHs were respectively 1,050±500 ng-TEQ dioxins (70% in gas phase) and 117± 21 mg PAHs (92% in gas phase) per kg of MSW, while those for plastic waste were 8.6 ng TEQ dioxins (36% in gas phase) and 85.2±0.06 mg PAHs (99% in gas phase). Using the activity data from own surveys and literature, we estimated the annual emissions from solid waste open burning in Southeast Asia for 2015. Higher emissions in the domain were seen during the dry months and over large urban areas. The large amounts of toxic pollutants emitted from this open burning activity call for actions to stop this practice which in turn requires integrated environmental management approach simultaneously considering both solid waste and air pollution.

Mono-energetic ions emission by nanosecond laser solid target irradiation

Energy Technology Data Exchange (ETDEWEB)

Muoio, A., E-mail: Annamaria.Muoio@lns.infn.it [Istituto Nazionale di Fisica Nucleare – Laboratori Nazionali del Sud, Via S. Sofia 62, 95123 Catania (Italy); Dipartimento di Fisica e Scienze della Terra, Università degli Studi di Messina, Viale F.S. D’Alcontres 31, 98166 Messina (Italy); Tudisco, S. [Istituto Nazionale di Fisica Nucleare – Laboratori Nazionali del Sud, Via S. Sofia 62, 95123 Catania (Italy); Altana, C. [Istituto Nazionale di Fisica Nucleare – Laboratori Nazionali del Sud, Via S. Sofia 62, 95123 Catania (Italy); Dipartimento di Fisica e Astronomia, Università degli Studi di Catania, Via S. Sofia 64, 95123 Catania (Italy); Lanzalone, G. [Istituto Nazionale di Fisica Nucleare – Laboratori Nazionali del Sud, Via S. Sofia 62, 95123 Catania (Italy); Università degli Studi di Enna “Kore”, Via delle Olimpiadi, 94100 Enna (Italy); Mascali, D.; Cirrone, G.A.P.; Schillaci, F. [Istituto Nazionale di Fisica Nucleare – Laboratori Nazionali del Sud, Via S. Sofia 62, 95123 Catania (Italy); Trifirò, A. [Dipartimento di Fisica e Scienze della Terra, Università degli Studi di Messina, Viale F.S. D’Alcontres 31, 98166 Messina (Italy); Sezione INFN, Catania (Italy)

2016-09-01

An experimental campaign aiming to investigate the acceleration mechanisms through laser–matter interaction in nanosecond domain has been carried out at the LENS (Laser Energy for Nuclear Science) laboratory of INFN-LNS, Catania. Pure Al targets were irradiated by 6 ns laser pulses at different pumping energies, up to 2 J. Advanced diagnostics tools were used to characterize the plasma plume and ion production. We show the preliminary results of this experimental campaign, and especially the ones showing the production of multicharged ions having very narrow energy spreads.

Aligning corporate greenhouse-gas emissions targets with climate goals

NARCIS (Netherlands)

Krabbe, Oskar; Linthorst, Giel; Blok, Kornelis; Crijns-Graus, Wina; Vuuren, Van Detlef P.; Höhne, Niklas; Faria, Pedro; Aden, Nate; Pineda, Alberto Carrillo

2015-01-01

Corporate climate action is increasingly considered important in driving the transition towards a low-carbon economy. For this, it is critical to ensure translation of global goals to greenhouse-gas (GHG) emissions reduction targets at company level. At the moment, however, there is a lack of

Aligning corporate greenhouse-gas emissions targets with climate goals

NARCIS (Netherlands)

Krabbe, Oskar; Linthorst, Giel; Blok, Kornelis|info:eu-repo/dai/nl/07170275X; Crijns-Graus, Wina|info:eu-repo/dai/nl/308005015; Van Vuuren, Detlef P.|info:eu-repo/dai/nl/11522016X; Höhne, Niklas; Faria, Pedro; Aden, Nate; Pineda, Alberto Carrillo

2015-01-01

Corporate climate action is increasingly considered important in driving the transition towards a low-carbon economy. For this, it is critical to ensure translation of global goals to greenhouse-gas (GHG) emissions reduction targets at company level. At the moment, however, there is a lack of clear

Dynamics of interaction of ultrashort laser pulses with solid targets

International Nuclear Information System (INIS)

Cang Yu; Wang Wei; Zhang Jie

2001-01-01

Using Saha equation, a simple model is proposed for the dynamics of interaction between ultrashort laser pulses and solid targets. An adiabatic expansion model is adopted to study the expansion phase after the heating phase. Temporal evolvement of the dynamics of the interaction is obtained, from which the electron temperature, density, ionization balances can be determined

Plasma emission induced by an Nd-YAG laser at low pressure on solid organic sample, its mechanism, and analytical application

International Nuclear Information System (INIS)

Suliyanti, Maria Margaretha; Sardy, Sar; Kusnowo, Anung; Hedwig, Rinda; Abdulmadjid, Syahrun Nur; Kurniawan, Koo Hendrik; Lie, T.J.; Pardede, Marincan; Kagawa, Kiichiro; Tjia, M.O.

2005-01-01

An Nd-YAG laser (1064 nm, 120 mJ, 8 ns) was focused on various types of solid organic samples such as a black acrylic plate, a black polyvinyl chloride plastic sheet, and a methoxy polyaniline film coated on the surface of a glass substrate, under a surrounding air pressure of 2 Torr. A modulated plasma technique was used to study the mechanism of excitation of the emission of the organic material. As a result, we conclude that ablated atoms and molecules are excited by a shock-wave mechanism, similar to the case of hard samples such as metal. The ablation speed of hydrogen emission (H I 656.2 nm) was examined and the results show that the release speed of the ablated atoms is relatively low (less than Mach 10) and persists for a longer period of time (around 1 μs); this phenomenon can be understood by assuming that the soft target absorbs recoil energy, causing a low release speed of ablated atoms which would form the shock wave. This was overcome by placing a subtarget on the back of the soft sample so as to enhance the repelling force, thus increasing the release speed of the atoms. A possible application of the low-pressure plasma on an organic solid was demonstrated in the detection of chlorine in a black polyvinyl chloride plastic sheet

Greenhouse gas emissions control in integrated municipal solid waste management through mixed integer bilevel decision-making

Energy Technology Data Exchange (ETDEWEB)

He, Li, E-mail: li.he@iseis.org [MOE Key Laboratory of Regional Energy Systems Optimization, S and C Academy of Energy and Environmental Research, North China Electric Power University, Beijing 102206 (China); Huang, G.H.; Lu, Hongwei [MOE Key Laboratory of Regional Energy Systems Optimization, S and C Academy of Energy and Environmental Research, North China Electric Power University, Beijing 102206 (China)

2011-10-15

Highlights: {yields} We used bilevel analysis to treat two objectives at different levels. {yields} The model can identify allocation schemes for waste flows. {yields} The model can support waste timing, sizing, and siting for facility expansions. {yields} The model can estimate minimized total management cost and GHG emissions. - Abstract: Recent studies indicated that municipal solid waste (MSW) is a major contributor to global warming due to extensive emissions of greenhouse gases (GHGs). However, most of them focused on investigating impacts of MSW on GHG emission amounts. This study presents two mixed integer bilevel decision-making models for integrated municipal solid waste management and GHG emissions control: MGU-MCL and MCU-MGL. The MGU-MCL model represents a top-down decision process, with the environmental sectors at the national level dominating the upper-level objective and the waste management sectors at the municipal level providing the lower-level objective. The MCU-MGL model implies a bottom-up decision process where municipality plays a leading role. Results from the models indicate that: the top-down decisions would reduce metric tonne carbon emissions (MTCEs) by about 59% yet increase about 8% of the total management cost; the bottom-up decisions would reduce MTCE emissions by about 13% but increase the total management cost very slightly; on-site monitoring and downscaled laboratory experiments are still required for reducing uncertainty in GHG emission rate from the landfill facility.

Greenhouse gas emission controls : differentiated vs. flat rate targets : impacts and concerts

International Nuclear Information System (INIS)

Heydanek, D.

1997-01-01

Continuing the discussion on differentiation in greenhouse gas emission targets and timetables for all nations, the different implications of differentiation vs. flat rate controls were examined. A scenario of how different targets for different countries based on national circumstances might be implemented, was presented. Implications of differentiation for the Dow Chemical Company were also reviewed. For more than 20 years, Dow has practiced leading edge energy efficiency in environmental management systems and has committed to a series of environmental, health and safety goals. The company believes that at the international level, fully differentiated targets and timetables need to be negotiated, party by party, by the 150 nations who agreed to stabilize greenhouse gas emissions at 1990 levels by year 2000. It was suggested that a strong disincentive exists to delivering energy efficiency beyond compliance. It was predicted that despite efficiency, the energy intensive assets in place today in Annex I countries will be disadvantaged and prematurely retired as the costs of greenhouse gas emission controls grow and exert pressure to move productive capacity offshore

Spectroscopic investigation of the charge dynamics of heavy ions penetrating solid and gaseous targets

International Nuclear Information System (INIS)

Korostiy, S.

2007-01-01

This thesis presents the study of the slowing down process of fast heavy ions inside matter. In the framework of this research, the influence of the target density on the stopping process is investigated. Experiments on the interaction of 48 Ca 6+ - 48 Ca 10+ and 26 Mg 5+ ion beams with initial energies of 11.4 MeV/u and 5.9 MeV/u with solid and gaseous targets have been carried out. A novel diagnostic method, X-ray spectroscopy of K-shell projectile radiation, is used to determine the ion charge state in relation to its velocity during the penetration of fast heavy ions inside the stopping material. A spatially resolved analysis of the projectile and target radiation in solids is achieved for the first time. The application of low-density silica aerogels as stopping media provided a stretching of the ion stopping length by 20 - 100 times in comparison with solid quartz. The Doppler Effect observed on the projectile K-shell spectra is used to calculate the ion velocity in dependence on the ion penetration depth in the target material. A comparative analysis of K α spectra of fast heavy ions is performed in solid (silica aerogels) and gaseous targets (Ar and Ne gases) at the same ion energy. It is shown that the dominant role of collisions in dense matter leads to an increase of the effective ionization cross section at high ion velocity and suppression of the electron capture to the projectile ion excited states at low ion velocity. As a result, an increase of the ion charge state in dense matter is observed. The experimentally detected effects are interpreted with numerical calculations of the projectile population kinetics, which are in good agreement with measurements. (orig.)

Spectroscopic investigation of the charge dynamics of heavy ions penetrating solid and gaseous targets

Energy Technology Data Exchange (ETDEWEB)

Korostiy, S

2007-01-15

This thesis presents the study of the slowing down process of fast heavy ions inside matter. In the framework of this research, the influence of the target density on the stopping process is investigated. Experiments on the interaction of {sup 48}Ca{sup 6+}-{sup 48}Ca{sup 10+} and {sup 26}Mg{sup 5+} ion beams with initial energies of 11.4 MeV/u and 5.9 MeV/u with solid and gaseous targets have been carried out. A novel diagnostic method, X-ray spectroscopy of K-shell projectile radiation, is used to determine the ion charge state in relation to its velocity during the penetration of fast heavy ions inside the stopping material. A spatially resolved analysis of the projectile and target radiation in solids is achieved for the first time. The application of low-density silica aerogels as stopping media provided a stretching of the ion stopping length by 20 - 100 times in comparison with solid quartz. The Doppler Effect observed on the projectile K-shell spectra is used to calculate the ion velocity in dependence on the ion penetration depth in the target material. A comparative analysis of K{sub {alpha}} spectra of fast heavy ions is performed in solid (silica aerogels) and gaseous targets (Ar and Ne gases) at the same ion energy. It is shown that the dominant role of collisions in dense matter leads to an increase of the effective ionization cross section at high ion velocity and suppression of the electron capture to the projectile ion excited states at low ion velocity. As a result, an increase of the ion charge state in dense matter is observed. The experimentally detected effects are interpreted with numerical calculations of the projectile population kinetics, which are in good agreement with measurements. (orig.)

Thermal-hydraulic design concept of the solid-target system of spallation neutron source

International Nuclear Information System (INIS)

Tanaka, F.; Hibiki, T.; Saito, Y.; Takeda, T.; Mishima, K.

2001-01-01

In relation to thermal-hydraulic design of the N-Arena solid-target system of the JHF project, heat transfer experiments were performed to obtain experimental data systematically on heat transfer coefficient and CHF for vertical upward and horizontal flows in a thin rectangular channel simulating a coolant channel of the proposed spallation neutron source. Thermal-hydraulic correlations which can be used for design calculations were proposed based on the obtained data. Finally tentative results of feasibility study on maximum beam power which could be attained with a solid target were presented. The result indicated that the condition for the onset of nucleate boiling is the most significant limiting factor to the maximum beam power. (author)

Search for Fermi shuttle mechanisms in electron emission from atomic collision sequences

International Nuclear Information System (INIS)

Suarez, S.; Jung, M.; Rothard, H.; Schosnig, M.; Maier, R.; Clouvas, A.; Groeneveld, K.O.

1994-01-01

In electron spectra induced by slow heavy ion bombardment of solids a high energy tail can be observed, which is suggested to be explained by multiple collision sequences. In order to find those multiple collision effects like the ''Fermi shuttle'' acceleration mechanism we measured doubly differential electron emission cross sections for H + (33.5-700 keV) impact on different targets (He, Ne, C and Au) as a function of projectile energy and electron emission angle. We observed a surprising target dependence of the electron emission within the range of electron energies close to that of the binary encounter electrons for all observed angles of emission. (orig.)

Analysis of Indirect Emissions Benefits of Wind, Landfill Gas, and Municipal Solid Waste Generation

Science.gov (United States)

Techniques are introduced to calculate the hourly indirect emissions benefits of three types of green power resources: wind energy, municipal solid waste (MSW) combustion, and landfill gas (LFG) combustion. These techniques are applied to each of the U.S. EPA's eGRID subregions i...

Photon emission from irradiated solids: Proceedings of the Werner Brandt workshop on penetration phenomena

International Nuclear Information System (INIS)

1986-11-01

The workshop was concerned with photon emission from irradiated solids and the present record of the proceedings consists of material solicited from each participant. The results range from detailed and complete manuscripts to skeletal remnants of Vugraph transparencies. Individual papers have been cataloged separately

Solid targets for 99mTc production on medical cyclotrons

International Nuclear Information System (INIS)

Hanemaayer, V.; Buckley, K.R.; Klug, J.; Ruth, T.J.; Schaffer, P.; Zeisler, S.K.; Benard, F.; Kovacs, M.; Leon, C.

2014-01-01

Recent disruptions in the molybdenum-technetium generator supply chain prompted a review of non-reactor based production methods for both 99 Mo and 99m Tc. Small medical cyclotrons (E p ∼ 16-24 MeV) are capable of producing Curie quantities of 99m Tc from isotopically enriched 100 Mo using the 100 Mo(p,2n) 99m Tc reaction. Unlike most other metallic target materials for routine production of medical radioisotopes, molybdenum cannot be deposited by reductive electroplating from aqueous salt solutions. To overcome this issue, we developed a new process for solid molybdenum targets based on the electrophoretic deposition of fine 100 Mo powder onto a tantalum plate, followed by high temperature sintering. The targets obtained were mechanically robust and thermally stable when irradiated with protons at high power density. (author)

Municipal solid waste management planning considering greenhouse gas emission trading under fuzzy environment.

Science.gov (United States)

Zhang, Xiaodong; Huang, Gordon

2014-03-15

Waste management activities can release greenhouse gases (GHGs) to the atmosphere, intensifying global climate change. Mitigation of the associated GHG emissions is vital and should be considered within integrated municipal solid waste (MSW) management planning. In this study, a fuzzy possibilistic integer programming (FPIM) model has been developed for waste management facility expansion and waste flow allocation planning with consideration of GHG emission trading in an MSW management system. It can address the interrelationships between MSW management planning and GHG emission control. The scenario of total system GHG emission control is analyzed for reflecting the feature that GHG emission credits may be tradable. An interactive solution algorithm is used to solve the FPIM model based on the uncertainty-averse preferences of decision makers in terms of p-necessity level, which represents the certainty degree of the imprecise objective. The FPIM model has been applied to a hypothetical MSW planning problem, where optimal decision schemes for facility expansion and waste flow allocation have been achieved with consideration of GHG emission control. The results indicate that GHG emission credit trading can decrease total system cost through re-allocation of GHG emission credits within the entire MSW management system. This will be helpful for decision makers to effectively determine the allowable GHG emission permits in practices. Copyright © 2014 Elsevier Ltd. All rights reserved.

Mamizu climate policy: an evaluation of Japanese carbon emissions reduction targets

International Nuclear Information System (INIS)

Pielke, Roger A Jr

2009-01-01

This letter evaluates Japan's so-called 'Mamizu' climate policies proposed in mid-2009 in terms of the implied rates of decarbonization of the Japanese economy for short-term and long-term targets. The letter uses the Kaya identity to structure the evaluation, employing both a bottom up approach (based on projections of future Japanese population, economic growth, and technology) and a top down approach (deriving implied rates of decarbonization consistent with the targets and various rates of economic growth). Both approaches indicate that the Japanese economy would have to achieve rates of decarbonization of 2.6% to meet a 2020 target of reducing emissions by 15% below 2005 levels, and 5.0% to meet a 2050 target of an 80% reduction below 2005 levels. A target of 25% below 1990 emissions proposed by the opposition party (which subsequently formed a government following elections in August 2009) implies a rate of decarbonization of 4.6% annually to 2020. The letter argues that international criticism of Japanese Mamizu climate policy proposals as being too weak was unfounded, and if anything, the proposals may have been too ambitious. In either case, climate policy would be strengthened through the support of a diversity of approaches to decarbonization.

Direct Quantification of Methane Emissions Across the Supply Chain: Identification of Mitigation Targets

Science.gov (United States)

Darzi, M.; Johnson, D.; Heltzel, R.; Clark, N.

2017-12-01

Researchers at West Virginia University's Center for Alternative Fuels, Engines, and Emissions have recently participated in a variety of studies targeted at direction quantification of methane emissions from across the natural gas supply chain. These studies included assessing methane emissions from heavy-duty vehicles and their fuel stations, active unconventional well sites - during both development and production, natural gas compression and storage facilities, natural gas engines - both large and small, two- and four-stroke, and low-throughput equipment associated with coal bed methane wells. Engine emissions were sampled using conventional instruments such as Fourier transform infrared spectrometers and heated flame ionization detection analyzers. However, to accurately quantify a wide range of other sources beyond the tailpipe (both leaks and losses), a full flow sampling system was developed, which included an integrated cavity-enhanced absorption spectrometer. Through these direct quantification efforts and analysis major sources of methane emissions were identified. Technological solutions and best practices exist or could be developed to reduce methane emissions by focusing on the "lowest-hanging fruit." For example, engine crankcases from across the supply chain should employ vent mitigation systems to reduce methane and other emissions. An overview of the direct quantification system and various campaign measurements results will be presented along with the identification of other targets for additional mitigation.

Greenhouse gas emission trends and projections in Europe 2012. Tracking progress towards Kyoto and 2020 targets

Energy Technology Data Exchange (ETDEWEB)

Gores, S.; Scheffler, M.; Graichen, V. [Oeko-Institut (Oeko), Freiburg (Germany)] [and others

2012-10-15

At the end of 2011, almost all European countries were on track towards their Kyoto targets for 2008-2012. The EU-15 also remained on track to achieve its Kyoto target. Italy, however, was not on track. Spain plans to acquire a large quantity of Kyoto units through the KP's flexible mechanisms to achieve its target. With emission caps already set for the economic sectors under the EU Emissions Trading Scheme (EU ETS), emissions reductions during 2012 in the sectors outside the EU ETS together with reductions by carbon sinks will set the frame for how many Kyoto units Member States need to acquire to reach their individual targets. Hence, both the development and delivery of adequate plans to acquire enough Kyoto credits is becoming increasingly important. ETS emissions from 2008 to 2011 were on average 5 % below these caps, which results in an oversupply of allowances. The EU ETS is undergoing important changes in view of the third trading phase from 2013 to 2020. Most EU Member States project that in 2020, their emissions outside the EU ETS will be lower than their national targets set under the Climate and Energy Package. However, further efforts will be necessary to achieve longer term reductions. (Author)

Baseline options and greenhouse gas emission reduction of clean development mechanism project in urban solid waste management

Energy Technology Data Exchange (ETDEWEB)

Hiramatsu, Ai; Hanaki, K. [Department of Urban Engineering, School of Engineering, University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-8656 (Japan); Aramaki, T. [Research Center for Advanced Science and Technology, University of Tokyo, 4-6-1 Komaba, Meguro-ku, Tokyo 153-8904(Japan)

2003-07-01

The Clean Development Mechanism (CDM) was adopted in the Kyoto Protocol as a flexibility mechanism to reduce greenhouse gases (GHGs) and has been started with such projects as improving efficiency of individual technology. Although applying various countermeasures to urban areas has significant potentials for reducing GHGs, these countermeasures have not been proposed as CDM projects in the practical stage. A CDM project needs to be validated that it will reduce GHGs additionally compared with a baseline, that is, a predictive value of GHG emissions in the absence of the project. This study examined the introduction of solid waste incineration with electricity generation into three different cities, A, B and C. The main solid waste treatment and the main fuel source are landfill and coal, respectively, in City A, incineration and natural gas in City B, and landfill and hydro in City C. GHG emission reductions of each city under several baseline options assumed here were evaluated. Even if the same technology is introduced, the emission reduction greatly varies according to the current condition and the future plan of the city: 1043-1406 kg CO2/t of waste in City A, 198-580 kg CO2/t in City B, and wide range of zero to over 1000 kg CO2/t in City C. Baseline options also cause significant difference in the emission reduction even in the same city (City C). Incinerating solid waste after removing plastics by source separation in City B increased GHG emission reduction potential up to 730-900 kg CO2/t, which enhances the effectiveness as a CDM project.

Pig slurry acidification and separation techniques affect soil N and C turnover and N2O emissions from solid, liquid and biochar fractions

DEFF Research Database (Denmark)

Gomez Muñoz, Beatriz; Case, Sean; Jensen, Lars Stoumann

2016-01-01

the separated solid fractions in soil, but did not affect N2O and CO2 emissions. However acidification reduced soil N and C turnover from the liquid fraction. The use of more advanced separation techniques (flocculation and drainage > decanting centrifuge > screw press) increased N mineralisation from acidified...... solid fractions, but also increased N2O and CO2 emissions in soil amended with the liquid fraction. Finally, the biochar production from the solid fraction of pig slurry resulted in a very recalcitrant material, which reduced N and C mineralisation in soil compared to the raw solid fractions....

Rear surface light emission measurements from laser-produced shock waves in clear and Al-coated polystyrene targets

Science.gov (United States)

McLean, E. A.; Deniz, A. V.; Schmitt, A. J.; Stamper, J. A.; Obenschain, S. P.; Lehecka, T.; Mostovych, A. N.; Seely, J.

1999-08-01

The Nike KrF laser, with its very uniform focal distributions, has been used at intensities near 10 14 W/cm 2 to launch shock waves in polystyrene targets. The rear surface visible light emission differed between clear polystyrene (CH) targets and targets with a thin (125 nm) Al coating on the rear side. The uncoated CH targets showed a relatively slowly rising emission followed by a sudden fall when the shock emerges, while the Al-coated targets showed a rapid rise in emission when the shock emerges followed by a slower fall, allowing an unambiguous determination of the time the shock arrived at the rear surface. A half-aluminized target allowed us to observe this difference in a single shot. The brightness temperature of both the aluminized targets and the non-aluminized targets was slightly below but close to rear surface temperature predictions of a hydrodynamic code. A discussion of preheat effects is given.

Energy and environmental implications of carbon emission reduction targets: Case of Kathmandu Valley, Nepal

International Nuclear Information System (INIS)

Shrestha, Ram M.; Rajbhandari, Salony

2010-01-01

This paper analyzes the sectoral energy consumption pattern and emissions of CO 2 and local air pollutants in the Kathmandu Valley, Nepal. It also discusses the evolution of energy service demands, structure of energy supply system and emissions from various sectors under the base case scenario during 2005-2050. A long term energy system planning model of the Kathmandu Valley based on the MARKet ALlocation (MARKAL) framework is used for the analyses. Furthermore, the paper analyzes the least cost options to achieve CO 2 emission reduction targets of 10%, 20% and 30% below the cumulative emission level in the base case and also discusses their implications for total cost, technology-mix, energy-mix and local pollutant emissions. The paper shows that a major switch in energy use pattern from oil and gas to electricity would be needed in the Valley to achieve the cumulative CO 2 emission reduction target of 30% (ER30). Further, the share of electricity in the cumulative energy consumption of the transport sector would increase from 12% in the base case to 24% in the ER30 case.

Preparation of chromatographic and solid-solvent extraction 99mTc generators using gel-type targets

International Nuclear Information System (INIS)

Le Van So

2000-01-01

We have studied two types of targets zirconium-molybdate (ZrMo) and titanium-molybdate (TiMo) prepared by precipitating reaction between ammonium-molybdate and zirconium-chloride or titanium-chloride solutions, respectively. Other types of targets were also prepared by co-precipitating ZrMo or TiMo with hydrous manganese-dioxide, hydrous silica, and hydrous titanium-dioxide or by impregnated ZrMo or TiMo with Iodate anions. The results on extraction of Tc-99m from neutron irradiated TiMo solid phase using solvents such as MEK, aceton, ethylic ether, chloroform, etc showed that separation yield (SY) of Tc-99m in case of aceton extraction was from 70% to 80% and in other cases non higher than 40%. The Tc-99m elution curves and column kinetic in case of aceton extraction (after evaporation of aceton and recovery of Tc-99m in 0,9% NaCl solution) was superior than in case chromatographic generator using saline eluant. As result obtained, two types of generators were successfully prepared and put into use: Chromatographic generator using titanium-molybdate target as packing material and saline as eluant. Solid-solvent extraction 99m Tc generator using titanium-molybdate target (as solid phase) and aceton as extracting solvent. (author)

X-ray determination of charge states of ions moving in solids

International Nuclear Information System (INIS)

Fortner, R.J.; Matthews, D.L.

1974-02-01

The first part of this work discusses previous measurements of x-ray spectra and thick-target yields for Ar ions moving in solid graphite targets. These data are strongly affected by ''solid target effects.'' There are some rather serious limitations in the above measurements. This proposal solicits funds to expand the program to eliminate the limitations. The second part of the proposal contains a more detailed presentation of three types of measurements. These involve the extension of work to other collision systems, the development of an Auger electron spectrometer, and the use of a 7-m grazing-incidence spectrograph for x-ray spectroscopy. These measurements will enable testing of current pictures describing ions moving in solids and shed light on the feasibility of producing a beam of ions which could give rise to amplified stimulated x-ray emission (x-ray laser). (11 figures) (U.S.)

Photon emission produced by particle-surface collisions

International Nuclear Information System (INIS)

White, C.W.; Tolk, N.H.

1976-02-01

Visible, ultraviolet, and infrared optical emission results from low-energy (20 eV-10 keV) particle-surface collisions. Several distinct kinds of collision induced optical radiation are discussed which provide fundamental information on particle-solid collision processes. Line radiation arises from excited states of sputtered surface constituents and backscattered beam particles. This radiation uniquely identifies the quantum state of sputtered or reflected particles, provides a method for identifying neutral atoms sputtered from the surface, and serves as the basis for a sensitive surface analysis technique. Broadband radiation from the bulk of the solid is attributed to the transfer of projectile energy to the electrons in the solid. Continuum emission observed well in front of transition metal targets is believed to arise from excited atom clusters (diatomic, triatomic, etc.) ejected from the solid in the sputtering process. Application of sputtered atom optical radiation for surface and depth profile analysis is demonstrated for the case of submonolayer quantities of chromium on silicon and aluminum implanted in SiO 2

Source emission and model evaluation of formaldehyde from composite and solid wood furniture in a full-scale chamber

Science.gov (United States)

Liu, Xiaoyu; Mason, Mark A.; Guo, Zhishi; Krebs, Kenneth A.; Roache, Nancy F.

2015-12-01

This paper describes the measurement and model evaluation of formaldehyde source emissions from composite and solid wood furniture in a full-scale chamber at different ventilation rates for up to 4000 h using ASTM D 6670-01 (2007). Tests were performed on four types of furniture constructed of different materials and from different manufacturers. The data were used to evaluate two empirical emission models, i.e., a first-order and power-law decay model. The experimental results showed that some furniture tested in this study, made only of solid wood and with less surface area, had low formaldehyde source emissions. The effect of ventilation rate on formaldehyde emissions was also examined. Model simulation results indicated that the power-law decay model showed better agreement than the first-order decay model for the data collected from the tests, especially for long-term emissions. This research was limited to a laboratory study with only four types of furniture products tested. It was not intended to comprehensively test or compare the large number of furniture products available in the market place. Therefore, care should be taken when applying the test results to real-world scenarios. Also, it was beyond the scope of this study to link the emissions to human exposure and potential health risks.

Atmospheric stabilization of CO2 emissions: Near-term reductions and absolute versus intensity-based targets

International Nuclear Information System (INIS)

Timilsina, Govinda R.

2008-01-01

This study analyzes CO 2 emissions reduction targets for various countries and geopolitical regions by the year 2030 to stabilize atmospheric concentrations of CO 2 at 450 ppm (550 ppm including non-CO 2 greenhouse gases) level. It also determines CO 2 intensity cuts that would be required in those countries and regions if the emission reductions were to be achieved through intensity-based targets without curtailing their expected economic growth. Considering that the stabilization of CO 2 concentrations at 450 ppm requires the global trend of CO 2 emissions to be reversed before 2030, this study develops two scenarios: reversing the global CO 2 trend in (i) 2020 and (ii) 2025. The study shows that global CO 2 emissions would be limited at 42 percent above 1990 level in 2030 if the increasing trend of global CO 2 emissions were to be reversed by 2020. If reversing the trend is delayed by 5 years, global CO 2 emissions in 2030 would be 52 percent higher than the 1990 level. The study also finds that to achieve these targets while maintaining expected economic growth, the global average CO 2 intensity would require a 68 percent drop from the 1990 level or a 60 percent drop from the 2004 level by 2030

Methane emission from ruminants and solid waste: A critical analysis of baseline and mitigation projections for climate and policy studies

Science.gov (United States)

Matthews, E.

2012-12-01

Current and projected estimates of methane (CH4) emission from anthropogenic sources are numerous but largely unexamined or compared. Presented here is a critical appraisal of CH4 projections used in climate-chemistry and policy studies. We compare emissions for major CH4 sources from several groups, including our own new data and RCP projections developed for climate-chemistry models for the next IPCC Assessment Report (AR5). We focus on current and projected baseline and mitigation emissions from ruminant animals and solid waste that are both predicted to rise dramatically in coming decades, driven primarily by developing countries. For waste, drivers include increasing urban populations, higher per capita waste generation due to economic growth and increasing landfilling rates. Analysis of a new global data base detailing waste composition, collection and disposal indicates that IPCC-based methodologies and default data overestimate CH4 emission for the current period which cascades into substantial overestimates in future projections. CH4 emission from solid waste is estimated to be ~10-15 Tg CH4/yr currently rather than the ~35 Tg/yr often reported in the literature. Moreover, emissions from developing countries are unlikely to rise rapidly in coming decades because new management approaches, such as sanitary landfills, that would increase emissions are maladapted to infrastructures in these countries and therefore unlikely to be implemented. The low current emission associated with solid waste (~10 Tg), together with future modest growth, implies that mitigation of waste-related CH4 emission is a poor candidate for slowing global warming. In the case of ruminant animals (~90 Tg CH4/yr currently), the dominant assumption driving future trajectories of CH4 emission is a substantial increase in meat and dairy consumption in developing countries to be satisfied by growing animal populations. Unlike solid waste, current ruminant emissions among studies exhibit a

Real-time boronization in PBX-M using erosion of solid boronized targets

International Nuclear Information System (INIS)

Kugel, H.W.; Timberlake, J.; Bell, R.; LeBlanc, B.; Okabayashi, M.; Paul, S.; Tighe, W.; Hirooka, Y.

1994-11-01

Thirty one real-time boronizations were applied to PBX-M using the plasma erosion of solid target probes. More than 17 g of boron were deposited in PBX-M using this technique. The probes were positioned at the edge plasma to optimize vaporization and minimize spallation. Auger depth profile analysis of poloidal and toroidal deposition sample coupon arrays indicate that boron was transported by the plasma around the torus and deep into the divertors. During discharges with continuous real-time boronization, low-Z and high-Z impurities decreased rapidly as plasma surfaces were covered during the first 20-30 discharges. After boronization, a short-term improvement in plasma conditions persisted prior to significant boron erosion from plasma surfaces, and a longer term, but less significant improvement persisted as boron farther from the edge continued gettering. Real-time solid target boronization has been found to be very effective for accelerating conditioning to new regimes and maintaining high performance plasma conditions

Emissions trading - an opportunity for sustainable solid waste management in developing and emerging countries?; Emissionshandel - Chance fuer eine nachhaltige Abfallwirtschaft in Entwicklungs- und Schwellenlaendern

Energy Technology Data Exchange (ETDEWEB)

Pfaff-Simoneit, W. [Kompetenzzentrum Wasser- und Abfallwirtschaft der KfW Entwicklungsbank, Frankfurt am Main (Germany)

2006-03-15

Emissions trading in the context of the Kyoto Protocol becomes increasingly important for solid waste management projects in developing and emerging countries. Compared with the emissions of the applied so called ''baseline'' in such countries, significant reductions of one of the most harmful greenhouse gases, methane, can be realized just by means of collecting and treating (controlled combustion) landfill gas. Even stronger reductions can be achieved by means of pre-treating of solid wastes. Revenues generated by sales of emission-reductions can cover up to 20-30% of the cost of an environmentally sound solid waste management system. However advanced solid waste technologies can currently only be applied under specific conditions (e.g. in Metropolitan cities) due to the limited willingness and ability of the waste producers to pay higher fees required by such systems.

The impact of municipal solid waste treatment methods on greenhouse gas emissions in Lahore, Pakistan.

Science.gov (United States)

Batool, Syeda Adila; Chuadhry, Muhammad Nawaz

2009-01-01

The contribution of existing municipal solid waste management to emission of greenhouse gases and the alternative scenarios to reduce emissions were analyzed for Data Ganj Bukhsh Town (DGBT) in Lahore, Pakistan using the life cycle assessment methodology. DGBT has a population of 1,624,169 people living in 232,024 dwellings. Total waste generated is 500,000 tons per year with an average per capita rate of 0.84kg per day. Alternative scenarios were developed and evaluated according to the environmental, economic, and social atmosphere of the study area. Solid waste management options considered include the collection and transportation of waste, collection of recyclables with single and mixed material bank container systems (SMBCS, MMBCS), material recovery facilities (MRF), composting, biogasification and landfilling. A life cycle inventory (LCI) of the six scenarios along with the baseline scenario was completed; this helped to quantify the CO2 equivalents, emitted and avoided, for energy consumption, production, fuel consumption, and methane (CH4) emissions. LCI results showed that the contribution of the baseline scenario to the global warming potential as CO2 equivalents was a maximum of 838,116 tons. The sixth scenario had a maximum reduction of GHG emissions in terms of CO2 equivalents of -33,773 tons, but the most workable scenario for the current situation in the study area is scenario 5. It saves 25% in CO2 equivalents compared to the baseline scenario.

The impact of municipal solid waste treatment methods on greenhouse gas emissions in Lahore, Pakistan

International Nuclear Information System (INIS)

Batool, Syeda Adila; Chuadhry, Muhammad Nawaz

2009-01-01

The contribution of existing municipal solid waste management to emission of greenhouse gases and the alternative scenarios to reduce emissions were analyzed for Data Ganj Bukhsh Town (DGBT) in Lahore, Pakistan using the life cycle assessment methodology. DGBT has a population of 1,624,169 people living in 232,024 dwellings. Total waste generated is 500,000 tons per year with an average per capita rate of 0.84 kg per day. Alternative scenarios were developed and evaluated according to the environmental, economic, and social atmosphere of the study area. Solid waste management options considered include the collection and transportation of waste, collection of recyclables with single and mixed material bank container systems (SMBCS, MMBCS), material recovery facilities (MRF), composting, biogasification and landfilling. A life cycle inventory (LCI) of the six scenarios along with the baseline scenario was completed; this helped to quantify the CO 2 equivalents, emitted and avoided, for energy consumption, production, fuel consumption, and methane (CH 4 ) emissions. LCI results showed that the contribution of the baseline scenario to the global warming potential as CO 2 equivalents was a maximum of 838,116 tons. The sixth scenario had a maximum reduction of GHG emissions in terms of CO 2 equivalents of -33,773 tons, but the most workable scenario for the current situation in the study area is scenario 5. It saves 25% in CO 2 equivalents compared to the baseline scenario

Quantifying greenhouse gas emissions from municipal solid waste dumpsites in Cameroon.

Science.gov (United States)

Ngwabie, N Martin; Wirlen, Yvette L; Yinda, Godwin S; VanderZaag, Andrew C

2018-03-02

Open dumpsites that receive municipal solid waste are potentially significant sources of greenhouse gas (GHG) emissions into the atmosphere. There is little data available on emissions from these sources, especially in the unique climate and management of central Africa. This research aimed at quantifying CH 4 , N 2 O and CO 2 emissions from two open dumpsites in Cameroon, located in Mussaka-Buea, regional headquarters of the South West Region and in Mbellewa-Bamenda, regional headquarters of the North West Region. Emissions were measured during the wet season (May 2015 and August 2016) at the Mussaka and Mbellewa dumpsites respectively. Dumpsite surfaces were partitioned into several zones for emission measurements, based on the current activity and the age of the waste. Static flux chambers were used to quantify gas emission rates thrice a day (mornings, afternoons and evenings). Average emissions were 96.80 ± 144 mg CH 4 m -2  min -1 , 0.20 ± 0.43 mg N 2 O m -2  min -1 and 224.78 ± 312 mg CO 2 m -2  min -1 in the Mussaka dumpsite, and 213.44 ± 419 mg CH 4 m -2  min -1 , 0.15 ± 0.15 mg N 2 O m -2  min -1 and 1103.82 ± 1194 mg CO 2 m -2  min -1 at the Mbellewa dumpsite. Emissions as high as 1784 mg CH 4 m -2  min -1 , 2.3 mg N 2 O m -2  min -1 and 5448 mg CO 2 m -2  min -1 were measured from both dumpsites. Huge variations observed in emissions between the different zones on the waste surface were likely a result of the heterogeneous nature of the waste, different stages in waste decomposition and different environmental conditions within the waste. Management activities that disturb waste, such as spreading and compressing potentially increase gas emissions, while covering waste with a layer of soil potentially mitigate gas emissions. Recommendations were for dumpsites to be upgraded to sanitary landfills, and biogas production from such landfills should be exploited to reduce CH 4 emissions

Vascular targeted therapy with anti-prostate-specific membrane antigen monoclonal antibody J591 in advanced solid tumors.

Science.gov (United States)

Milowsky, Matthew I; Nanus, David M; Kostakoglu, Lale; Sheehan, Christine E; Vallabhajosula, Shankar; Goldsmith, Stanley J; Ross, Jeffrey S; Bander, Neil H

2007-02-10

Based on prostate-specific membrane antigen (PSMA) expression on the vasculature of solid tumors, we performed a phase I trial of antibody J591, targeting the extracellular domain of PSMA, in patients with advanced solid tumor malignancies. This was a proof-of-principle evaluation of PSMA as a potential neovascular target. The primary end points were targeting,toxicity, maximum-tolerated dose, pharmacokinetics (PK), and human antihuman antibody (HAHA) response. Patients had advanced solid tumors previously shown to express PSMA on the neovasculature. They received 111Indium (111ln)-J591 for scintigraphy and PK, followed 2 weeks later by J591 with a reduced amount of 111In for additional PK measurements. J591 dose levels were 5, 10, 20, 40, and 80 mg. The protocol was amended for six weekly administrations of unchelated J591. Patients with a response or stable disease were eligible for re-treatment. Immunohistochemistry assessed PSMA expression in tumor tissues. Twenty-seven patients received monoclonal antibody (mAb) J591. Treatment was well tolerated. Twenty (74%) of 27 patients had at least one area of known metastatic disease targeted by 111In-J591, with positive imaging seen in patients with kidney, bladder, lung, breast, colorectal, and pancreatic cancers, and melanoma. Seven of 10 patient specimens available for immunohistochemical assessment of PSMA expression in tumor-associated vasculature demonstrated PSMA staining. No HAHA response was seen. Three patients of 27 with stable disease received re-treatment. Acceptable toxicity and excellent targeting of known sites of metastases were demonstrated in patients with multiple solid tumor types, highlighting a potential role for the anti-PSMA antibody J591 as a vascular-targeting agent.

Characterization of nuclear physics targets using Rutherford backscattering and particle induced X-ray emission

International Nuclear Information System (INIS)

Rubehn, T.; Wozniak, G.J.; Phair, L.; Moretto, L.G.; Yu, K.M.

1997-01-01

Rutherford backscattering and particle induced X-ray emission have been utilized to precisely characterize targets used in nuclear fission experiments. The method allows for a fast and non-destructive determination of target thickness, homogeneity and element composition. (orig.)

Interaction of 14 MeV neutrons with hydrogenated target proton emission calculation

International Nuclear Information System (INIS)

Martin, G.; Perez, N.; Desdin.

1996-01-01

Using neutron emission data of a 14 MeV neutron generator, a paraffin target, and based on the n + H 1 → n '+ p reaction, have been obtained the characteristics of the proton emission in a proton-neutron mixed field. It was used Monte Carlo simulation and it was obtained the proton output as function of the converter width and the energy spectrum of protons corresponding to different converter thickness. Among 0.07 and 0.2 cm there is a maximum zone for the proton emission. The energy spectrum agrees with obtained on previous papers. Figures showing these results are provided

Greenhouse gas emissions from municipal solid waste management in Vientiane, Lao PDR.

Science.gov (United States)

Babel, Sandhya; Vilaysouk, Xaysackda

2016-01-01

Municipal solid waste (MSW) is one of the major environmental problems throughout the world including in Lao PDR. In Vientiane, due to the lack of a collection service, open burning and illegal dumping are commonly practised. This study aims to estimate the greenhouse gas (GHG) emission from the current situation of MSW management (MSWM) in Vientiane and proposes an alternative solution to reduce the GHG emission and environmental impacts. The 2006 Intergovernmental Panel on Climate Change (IPCC) Guidelines for National Greenhouse Gas Inventories (IPCC 2006 model) are used for the estimation of GHG emission from landfill and composting. For the estimation of GHG emission from open burning, the Atmospheric Brown Clouds Emission Inventory Manual (ABC EIM) is used. In Vientiane, a total of 232, 505 tonnes year(-1) of MSW was generated in 2011. Waste generation in Vientiane is 0.69 kg per capita per day, and about 31% of the total MSW generated was directly sent to landfill (71,162 tonnes year(-1)). The total potential GHG emission from the baseline scenario in 2011 was 110,182 tonnes year(-1) CO2-eq, which is 0.15 tonne year(-1) CO2-eq per capita. From the three MSWM scenarios proposed, scenario S3, which includes recycling, composting and landfilling, seems to be an effective solution for dealing with MSW in Vientiane with less air pollution, and is environmentally friendly. The total GHG emission in scenario S3 is reduced to 91,920 tonnes year(-1) CO2-eq (47% reduction), compared with the S1 scenario where all uncollected waste is diverted to landfill. © The Author(s) 2015.

Positron emission tomography response criteria in solid tumours criteria for quantitative analysis of [18F]-fluorodeoxyglucose positron emission tomography with integrated computed tomography for treatment response assessment in metastasised solid tumours: All that glitters is not gold.

Science.gov (United States)

Willemsen, Annelieke E C A B; Vlenterie, Myrella; van Herpen, Carla M L; van Erp, Nielka P; van der Graaf, Winette T A; de Geus-Oei, Lioe-Fee; Oyen, Wim J G

2016-03-01

For solid tumours, quantitative analysis of [(18)F]-fluorodeoxyglucose positron emission tomography with integrated computed tomography potentially can have significant value in early response assessment and thereby discrimination between responders and non-responders at an early stage of treatment. Standardised strategies for this analysis have been proposed, and the positron emission tomography response criteria in solid tumours (PERCIST) criteria can be regarded as the current standard to perform quantitative analysis in a research setting, yet is not implemented in daily practice. However, several exceptions and limitations limit the feasibility of PERCIST criteria. In this article, we point out dilemmas that arise when applying proposed criteria like PERCIST on an expansive set of patients with metastasised solid tumours. Clinicians and scientists should be aware of these limitations to prevent that methodological issues impede successful introduction of research data into clinical practice. Therefore, to deliver on the high potential of quantitative imaging, consensus should be reached on a standardised, feasible and clinically useful analysis methodology. This methodology should be applicable in the majority of patients, tumour types and treatments. Copyright © 2015 Elsevier Ltd. All rights reserved.

Uncertain long-run emissions targets, CO2 price and global energy transition. A general equilibrium approach

International Nuclear Information System (INIS)

Durand-Lasserve, Olivier; Smeers, Yves; Pierru, Axel

2010-01-01

The persistent uncertainty about mid-century CO 2 emissions targets is likely to affect not only the technological choices that energy-producing firms will make in the future but also their current investment decisions. We illustrate this effect on CO 2 price and global energy transition within a MERGE-type general-equilibrium model framework, by considering simple stochastic CO 2 policy scenarios. In these scenarios, economic agents know that credible long-run CO 2 emissions targets will be set in 2020, with two possible outcomes: either a hard cap or a soft cap. Each scenario is characterized by the relative probabilities of both possible caps. We derive consistent stochastic trajectories - with two branches after 2020 - for prices and quantities of energy commodities and CO 2 emissions permits. The impact of uncertain long-run CO 2 emissions targets on prices and technological trajectories is discussed. In addition, a simple marginal approach allows us to analyze the Hotelling rule with risk premia observed for certain scenarios. (author)

Radiation Dose Measurement for High-Intensity Laser Interactions with Solid Targets at SLAC

Energy Technology Data Exchange (ETDEWEB)

Liang, Taiee [SLAC National Accelerator Lab., Menlo Park, CA (United States)

2015-09-25

A systematic study of photon and neutron radiation doses generated in high-intensity laser-solid interactions is underway at SLAC National Accelerator Laboratory. We found that these laser-solid experiments are being performed using a 25 TW (up to 1 J in 40 fs) femtosecond pulsed Ti:sapphire laser at the Linac Coherent Light Source’s (LCLS) Matter in Extreme Conditions (MEC) facility. Additionally, radiation measurements were performed with passive and active detectors deployed at various locations inside and outside the target chamber. Results from radiation dose measurements for laser-solid experiments at SLAC MEC in 2014 with peak intensity between 10¹⁸ to 7.1x10¹⁹ W/cm² are presented.

Curbing dioxin emissions from municipal solid waste incineration in China: Re-thinking about management policies and practices

Energy Technology Data Exchange (ETDEWEB)

Cheng Hefa, E-mail: hefac@umich.ed [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Hu Yuanan [Education Program for Gifted Youth, Stanford University, Stanford, CA 94025 (United States)

2010-09-15

As one of the countries with large amounts of dioxin releases, the control of dioxins is a major challenge for China. Municipal solid waste (MSW) incineration should be considered a high priority source of dioxin emissions because it is playing an increasingly more important role in waste management. MSW incineration in China has much higher emission rates of dioxins than in the developed countries, partially resulting from the gaps in the technologies of incineration and flue gas cleaning. Moreover, the current management policies and practices also contribute significantly to the problem. We recommend lowering dioxin emission standard, strengthening fly ash management, and improving regulation enforcement to reduce dioxin releases into the environment from MSW incineration. We also propose that alternative strategies should be considered on dioxin control and call for an expansion of economic instruments in waste management to reduce waste generation and thus the need for incineration. - The management policies and practices need to be improved to curb the increasing dioxin releases from municipal solid waste incineration in China.

Curbing dioxin emissions from municipal solid waste incineration in China: Re-thinking about management policies and practices

International Nuclear Information System (INIS)

Cheng Hefa; Hu Yuanan

2010-01-01

As one of the countries with large amounts of dioxin releases, the control of dioxins is a major challenge for China. Municipal solid waste (MSW) incineration should be considered a high priority source of dioxin emissions because it is playing an increasingly more important role in waste management. MSW incineration in China has much higher emission rates of dioxins than in the developed countries, partially resulting from the gaps in the technologies of incineration and flue gas cleaning. Moreover, the current management policies and practices also contribute significantly to the problem. We recommend lowering dioxin emission standard, strengthening fly ash management, and improving regulation enforcement to reduce dioxin releases into the environment from MSW incineration. We also propose that alternative strategies should be considered on dioxin control and call for an expansion of economic instruments in waste management to reduce waste generation and thus the need for incineration. - The management policies and practices need to be improved to curb the increasing dioxin releases from municipal solid waste incineration in China.

Vehicle emission factors of solid nanoparticles in the laboratory and on the road using Portable Emission Measurement Systems (PEMS

Directory of Open Access Journals (Sweden)

Barouch eGiechaskiel

2015-12-01

Full Text Available Emission inventories are used to quantify sources and identify trends in the emissions of air pollutants. They use vehicle-specific emission factors that are typically determined in the laboratory, through remote-sensing, vehicle chasing experiments and, more recently, on-board Portable Emission Measurement Systems (PEMS. Although PEMS is widely applied to measure gaseous pollutants, their application to Solid Particle Number (SPN emissions is new. In this paper, we discuss the current status of determining SPN emission factors both on the chassis dynamometer and on-road using PEMS-SPN. First, we determine the influence of the measurement equipment, ambient temperature, driving style and cycle characteristics, and the extra mass of the PEMS equipment on the SPN emissions. Afterward, we present the SPN emissions under type-approval conditions as well as on the road of two heavy-duty diesel vehicles equipped with Diesel Particulate Filter (DPF (one Euro VI, two light-duty diesel vehicles equipped with DPF, one light-duty vehicle equipped with a Port Fuel Injection engine (PFI, and seven Gasoline Direct Injection (GDI passenger cars (two Euro 6. We find that cold-start and strong accelerations tend to substantially increase SPN emissions. The two heavy-duty vehicles showed emissions around 2×10^13 p/km (Euro V truck and 6×10^10 p/km (Euro VI truck, respectively. One of the DPF-equipped light-duty vehicles showed emissions of 8×10^11 p/km, while the other one had one order of magnitude lower emissions. The PFI car had SPN emissions slightly higher than 1×10^12 p/km. The emissions of GDI cars spanned approximately from 8×10^11 p/km to 8×10^12 p/km. For the cars without DPF, the SPN emissions remained within a factor of two of the laboratory results. This factor was on average around 0.8 for the Euro 6 and 1.6 for the Euro 5 GDIs. The DPF equipped vehicles showed a difference of almost one order of magnitude between laboratory and on-road tests

Gaseous emissions during the solid state fermentation of different wastes for enzyme production at pilot scale.

Science.gov (United States)

Maulini-Duran, Caterina; Abraham, Juliana; Rodríguez-Pérez, Sheila; Cerda, Alejandra; Jiménez-Peñalver, Pedro; Gea, Teresa; Barrena, Raquel; Artola, Adriana; Font, Xavier; Sánchez, Antoni

2015-03-01

The emissions of volatile organic compounds (VOC), CH4, N2O and NH3 during the solid state fermentation process of some selected wastes to obtain different enzymes have been determined at pilot scale. Orange peel+compost (OP), hair wastes+raw sludge (HW) and winterization residue+raw sludge (WR) have been processed in duplicate in 50 L reactors to provide emission factors and to identify the different VOC families present in exhaust gaseous emissions. Ammonia emission from HW fermentation (3.2±0.5 kg Mg(-1) dry matter) and VOC emission during OP processes (18±6 kg Mg(-1) dry matter) should be considered in an industrial application of these processes. Terpenes have been the most emitted VOC family during all the processes although the emission of sulphide molecules during HW SSF is notable. The most emitted compound was dimethyl disulfide in HW and WR processes, and limonene in the SSF of OP. Copyright © 2014 Elsevier Ltd. All rights reserved.

Ranges, Reflection and Secondary Electron Emission for keV Hydrogen Ions Incident on Solid N2

DEFF Research Database (Denmark)

Børgesen, P.; Sørensen, H.; Hao-Ming, Chen

1983-01-01

Ranges were measured for 0.67–3.3 keV/amu hydrogen and deuterium ions in solid N2. Comparisons with similar results for N2-gas confirm the previously observed large phase effect in the stopping cross section. Measurements of the secondary electron emission coefficient for bulk solid N2 bombarded...... by 0.67–9 keV/amu ions also seem to support such a phase effect. It is argued that we may also extract information about the charge state of reflected projectiles....

Volatile compounds emission and health risk assessment during composting of organic fraction of municipal solid waste

DEFF Research Database (Denmark)

Mustafa, Muhammad Farooq; Liu, Yanjun; Duan, Zhenhan

2017-01-01

Degradation of mechanically sorted organic fraction (MSOF) of municipal solid waste in composting facilities is among the major contributors of volatile compounds (VCs) generation and emission, causes nuisance problems and health risks on site as well as in the vicinages. The aim of current study...

Stimulated emission in a solid-state ring laser with an SBS mirror

Science.gov (United States)

Barashkov, M. S.; Bel'Diugin, I. M.; Zolotarev, M. V.; Krymskii, M. I.; Oshkin, S. P.

1990-06-01

Experimental data are presented on a solid-state ring laser with an SBS mirror in the case of the initiation of stimulated emission by a series of pulses 200-300 ns in duration at a wavelength of 1.06 micron. It is shown that this laser can be suitable for the development of a laser source with radiation parameters (energy and transverse and temporal structure) that are controlled by an external signal. It is also suitable for the development of a low-threshold phase-conjugating mirror.

Experimental study for angular distribution of the hot electrons generated by femtosecond laser interaction with solid targets

International Nuclear Information System (INIS)

Cai, D.F.; Gu, Y.Q.; Zheng, Z.J.; Wen, T.S.; Chunyu, S.T.; Wang, Z.B.; Yang, X.D.

2003-01-01

The experimental results of angular distribution of hot electrons in the interaction of a 60 fs, 125 mJ, 800 nm, ∼10 17 W cm -2 laser pulse with Al targets are reported. Three obvious peaks of hot electrons emission have been observed, as there is a weak normal component of the laser electric field. These emission peaks are located in the directions of the specular reflection of the laser, the target normal, and the backreflection of the laser, respectively. In the case of the P-polarized laser pulse, which has a strong normal component of the laser electric field, the peak in the backreflection of the laser disappeared, and only two obvious peaks of hot electron emissions existed. It shows that the different directions of hot electrons emission are dominated by different absorption or acceleration mechanisms. The experimental result of the hot electrons energy spectrum at the target normal shows that the effective temperature of hot electrons is about 190 keV, which is consistent with a scaling law of the resonance absorption

Greenhouse gas emission mitigation relevant to changes in municipal solid waste management system.

Science.gov (United States)

Pikoń, Krzysztof; Gaska, Krzysztof

2010-07-01

Standard methods for assessing the environmental impact of waste management systems are needed to underpin the development and implementation of sustainable waste management practice. Life cycle assessment (LCA) is a tool for comprehensively ensuring such assessment and covers all impacts associated with waste management. LCA is often called "from cradle to grave" analysis. This paper integrates information on the greenhouse gas (GHG) implications of various management options for some of the most common materials in municipal solid waste (MSW). Different waste treatment options for MSW were studied in a system analysis. Different combinations of recycling (cardboard, plastics, glass, metals), biological treatment (composting), and incineration as well as land-filling were studied. The index of environmental burden in the global warming impact category was calculated. The calculations are based on LCA methodology. All emissions taking place in the whole life cycle system were taken into account. The analysis included "own emissions," or emissions from the system at all stages of the life cycle, and "linked emissions," or emissions from other sources linked with the system in an indirect way. Avoided emissions caused by recycling and energy recovery were included in the analysis. Displaced emissions of GHGs originate from the substitution of energy or materials derived from waste for alternative sources. The complex analysis of the environmental impact of municipal waste management systems before and after application of changes in MSW systems according to European Union regulations is presented in this paper. The evaluation is made for MSW systems in Poland.

Directional enhancement of selected high-order-harmonics from intense laser irradiated blazed grating targets.

Science.gov (United States)

Zhang, Guobo; Chen, Min; Liu, Feng; Yuan, Xiaohui; Weng, Suming; Zheng, Jun; Ma, Yanyun; Shao, Fuqiu; Sheng, Zhengming; Zhang, Jie

2017-10-02

Relativistically intense laser solid target interaction has been proved to be a promising way to generate high-order harmonics, which can be used to diagnose ultrafast phenomena. However, their emission direction and spectra still lack tunability. Based upon two-dimensional particle-in-cell simulations, we show that directional enhancement of selected high-order-harmonics can be realized using blazed grating targets. Such targets can select harmonics with frequencies being integer times of the grating frequency. Meanwhile, the radiation intensity and emission area of the harmonics are increased. The emission direction is controlled by tailoring the local blazed structure. Theoretical and electron dynamics analysis for harmonics generation, selection and directional enhancement from the interaction between multi-cycle laser and grating target are carried out. These studies will benefit the generation and application of laser plasma-based high order harmonics.

Allowable CO2 emissions based on regional and impact-related climate targets: The role of land processes

Science.gov (United States)

Seneviratne, S. I.; Donat, M.; Pitman, A.; Knutti, R.; Wilby, R.; Vogel, M.; Orth, R.

2016-12-01

Global temperature targets, such as the widely accepted "2° and 1.5° targets", may fail to communicate the urgency of reducing CO2 emissions because they are disconnected from their implications. The translation of CO2 emissions into regional- and impact-related climate targets is more powerful because such targets are more directly aligned with individual national interests. A recent publication (Seneviratne et al. 2016, Nature) reveals that regional changes in extreme temperatures and precipitation scale robustly with global temperature across scenarios, and thus with cumulative CO2 emissions. They thus allow a better communication of implied regional impacts associated with global targets for CO2 emissions. However, the regional responses are very varied and display strong differences in regional temperature and hydrological sensitivity. Process-based based analyses explain these divergences and highlight avenues for reducing uncertainties in regional projections of extremes, in particular related to the role of land-atmosphere feedbacks. These results have important implications for the design of regional mitigation and climate adaptation policies, for instance related to land use changes. Reference: Seneviratne, S.I., M.G. Donat, A.J. Pitman, R. Knutti, and R. Wilby, 2016, Nature, 529, 477-483, doi:10.1038/nature16542

A correction in the CDM methodological tool for estimating methane emissions from solid waste disposal sites.

Science.gov (United States)

Santos, M M O; van Elk, A G P; Romanel, C

2015-12-01

Solid waste disposal sites (SWDS) - especially landfills - are a significant source of methane, a greenhouse gas. Although having the potential to be captured and used as a fuel, most of the methane formed in SWDS is emitted to the atmosphere, mainly in developing countries. Methane emissions have to be estimated in national inventories. To help this task the Intergovernmental Panel on Climate Change (IPCC) has published three sets of guidelines. In addition, the Kyoto Protocol established the Clean Development Mechanism (CDM) to assist the developed countries to offset their own greenhouse gas emissions by assisting other countries to achieve sustainable development while reducing emissions. Based on methodologies provided by the IPCC regarding SWDS, the CDM Executive Board has issued a tool to be used by project developers for estimating baseline methane emissions in their project activities - on burning biogas from landfills or on preventing biomass to be landfilled and so avoiding methane emissions. Some inconsistencies in the first two IPCC guidelines have already been pointed out in an Annex of IPCC latest edition, although with hidden details. The CDM tool uses a model for methane estimation that takes on board parameters, factors and assumptions provided in the latest IPCC guidelines, while using in its core equation the one of the second IPCC edition with its shortcoming as well as allowing a misunderstanding of the time variable. Consequences of wrong ex-ante estimation of baseline emissions regarding CDM project activities can be of economical or environmental type. Example of the first type is the overestimation of 18% in an actual project on biogas from landfill in Brazil that harms its developers; of the second type, the overestimation of 35% in a project preventing municipal solid waste from being landfilled in China, which harms the environment, not for the project per se but for the undue generated carbon credits. In a simulated landfill - the same

Muon catalyzed fusion at very low temperature: A new target system

International Nuclear Information System (INIS)

Mulhauser, F.; Beveridge, J.L.; Marshall, G.M.

1994-10-01

Muon catalyzed fusion (μCF) processes are usually studied in gases or liquids. A new target system allows experiments on muonic hydrogen isotopes in solid hydrogen layers at 3K, where processes of the μCF cycle can be separated and the energy dependence of reactions can be measured. Muonic tritium atomic beams with energy of the order of 1 eV have been produced via transfer and emission from solid hydrogen target containing small tritium concentrations. The μt energy distribution overlaps the predicted muonic molecular (dμt) formation resonances. Preliminary time of flight results are shown. (author). 9 refs., 5 figs

Stimulated emission in a solid-state ring laser with an SBS mirror

Energy Technology Data Exchange (ETDEWEB)

Barashkov, M.S.; Bel' diugin, I.M.; Zolotarev, M.V.; Krymskii, M.I.; Oshkin, S.P.

1990-06-01

Experimental data are presented on a solid-state ring laser with an SBS mirror in the case of the initiation of stimulated emission by a series of pulses 200-300 ns in duration at a wavelength of 1.06 micron. It is shown that this laser can be suitable for the development of a laser source with radiation parameters (energy and transverse and temporal structure) that are controlled by an external signal. It is also suitable for the development of a low-threshold phase-conjugating mirror. 5 refs.

X-ray emission in heavy-ion collisions. Progress report, April 1, 1979-March 31, 1980

International Nuclear Information System (INIS)

Watson, R.L.

1980-04-01

Recent research in the cyclotron institute and department of chemistry at Texas A and M University on the x-ray emission in heavy-ion collisions is described. Areas covered include: spectra of Ka x-rays from 64 MeV sulfur ions traveling in solids; foil-excited Ka x-ray transitions in few-electron sulfur ions; high-resolution study of the target thickness dependence of x-ray emission from 65 MeV sulfur ions; dynamic screening of highly stripped sulfur ions in solids; Mg Ka x-ray satellites excited by ion bombardment, multiplet structure and dependence on projectile and chemical environment; angular distributions of beam and target Ka x-rays; chemical effects on K x-ray satellites of fluorine compounds; and a non-linear least-squares peak-fitting program employing Voight functions

Environmental and economic effects of the Copenhagen pledges and more ambitious emission reduction targets. Interim report

Energy Technology Data Exchange (ETDEWEB)

Schleich, Joachim; Duscha, Vicki; Peterson, Everett B. [Fraunhofer-Institut fuer System- und Innovationsforschung, Karlsruhe (Germany); Virginia Tech, Blacksburg, VA (United States). Dept. of Agricultural and Applied Economics

2010-06-15

Global carbon dioxide emissions need to be reduced by at least 50 to 85 % in 2050 compared to 2000 levels to limit global surface temperature increase to 2 C compared to preindustrial levels (IPCC 2007). As an intermediate greenhouse gas emission reduction target for industrialized countries in 2020 the IPCC (2007) confirmed a range of 25 % to 40 % compared to 1990, together with a substantial deviation from baseline in some developing regions, which was quantified as reductions in the range of 15 % to 30 % below baseline (den Elzen and Hoehne 2008). This report explores the environmental and economic effects of the pledges submitted by industrialized and major developing countries for 2020 under the Copenhagen Accord as quantifiable emission reductions or as NAMAs. Two scenarios reflect the lower (''weak'') and upper (''ambitious'') bounds of the Copenhagen pledges leading to emission reductions of 17 % below 1990 levels for Annex I countries and 13 % below reference levels for Non-Annex I countries. Both scenarios do not reach the level of ambition indicated as necessary by science to keep temperature increase below 2 C. In addition, two scenarios in accordance with the IPCC range for reaching a 2 C target are analyzed with industrialized countries in aggregate reducing their CO{sub 2}-emissions by 30 % and by 40 % in 2020 compared to 1990 levels, respectively. For all four policy scenarios the effects of emission paths leading to a global reduction target of 50 % below 1990 levels in 2050 are also simulated for 2030. In the scenarios for 2030 all but the least developed countries are assumed to take on emission targets, but emission caps are considerably less stringent for developing countries than for developed countries. In addition, a separate scenario is carried out which estimates the costs of an unconditioned EU 30 % emission reduction target. The analyses are carried out with the dynamic Computable General

Secondary emission detectors for fixed target experiments at Fermilab

International Nuclear Information System (INIS)

Drucker, R.; Ford, R.; Tassotto, G.

1998-02-01

A description of a Secondary Emission Electron Detector (SEED) is given. The SEEDs provide accurate profiles and positions at small wire spacing (125-500 mm) in a high energy, high rate environment that exceeds the capabilities of traditional segmented wire ion chambers (SWICs). This device has been designed and constructed to monitor beam position and profile of two fixed target beamlines, namely, KTeV (FNAL E-799, E-832) with an average beam sigma at target of 0.22 mm and NuTeV (FNAL E-815) with a sigma = 0.6 mm. KTeV took beam at an intensity of up to 5E12 800 GeV protons over a 20 sec spill and NuTeV received 1E13 800 GeV protons in five pings/spill

[Novel irradiation techniques in the treatment of solid tumours. Radiotherapy for metastases].

Science.gov (United States)

Mayer, Arpád; Póti, Zsuzsa

2014-02-23

Novel developments in percutaneous radiotherapy, such as positron emission tomography/computed tomography, adaptive radiation planning, intensity modulation radiotherapy and intensity modulated arc therapy (RapidArc), as well as the newer generation of image control (cone-beam computed tomography) and image guided radiotherapy ensure increased dosages of planning target volume and clinical target volume of solid tumours without damaging surrounding tissues and providing maximal protection. By raising the dosages of planned target volume and clinical target volume, these novel technical developments have created new indications in the treatment of solid tumours. With the aid of the cone-beam computed tomography and image guided radiotherapy the organ metastasis (lung, liver, spinal cord) and the primary tumour can be treated safety and effectively. Hypofractionation, dose escalation and the use of stereotactic devices can probably decrease radiation damage. The authors review the most common forms of evidence-based fractionation schemes used in irradiation therapy.

Antibody or Antibody Fragments: Implications for Molecular Imaging and Targeted Therapy of Solid Tumors

Directory of Open Access Journals (Sweden)

Katerina T. Xenaki

2017-10-01

Full Text Available The use of antibody-based therapeutics has proven very promising for clinical applications in cancer patients, with multiple examples of antibodies and antibody–drug conjugates successfully applied for the treatment of solid tumors and lymphomas. Given reported recurrence rates, improvements are clearly still necessary. A major factor limiting the efficacy of antibody-targeted cancer therapies may be the incomplete penetration of the antibody or antibody–drug conjugate into the tumor. Incomplete tumor penetration also affects the outcome of molecular imaging, when using such targeting agents. From the injection site until they arrive inside the tumor, targeting molecules are faced with several barriers that impact intratumoral distribution. The primary means of antibody transport inside tumors is based on diffusion. The diffusive penetration inside the tumor is influenced by both antibody properties, such as size and binding affinity, as well as tumor properties, such as microenvironment, vascularization, and targeted antigen availability. Engineering smaller antibody fragments has shown to improve the rate of tumor uptake and intratumoral distribution. However, it is often accompanied by more rapid clearance from the body and in several cases also by inherent destabilization and reduction of the binding affinity of the antibody. In this perspective, we discuss different cancer targeting approaches based on antibodies or their fragments. We carefully consider how their size and binding properties influence their intratumoral uptake and distribution, and how this may affect cancer imaging and therapy of solid tumors.

The history, genotoxicity, and carcinogenicity of carbon-based fuels and their emissions. Part 2: solid fuels.

Science.gov (United States)

Claxton, Larry D

2014-01-01

The combustion of solid fuels (like wood, animal dung, and coal) usually involves elevated temperatures and altered pressures and genotoxicants (e.g., PAHs) are likely to form. These substances are carcinogenic in experimental animals, and epidemiological studies implicate these fuels (especially their emissions) as carcinogens in man. Globally, ∼50% of all households and ∼90% of all rural households use solid fuels for cooking or heating and these fuels often are burnt in simple stoves with very incomplete combustion. Exposed women and children often exhibit low birth weight, increased infant and perinatal mortality, head and neck cancer, and lung cancer although few studies have measured exposure directly. Today, households that cannot meet the expense of fuels like kerosene, liquefied petroleum gas, and electricity resort to collecting wood, agricultural residue, and animal dung to use as household fuels. In the more developed countries, solid fuels are often used for electric power generation providing more than half of the electricity generated in the United States. The world's coal reserves, which equal approximately one exagram, equal ∼1 trillion barrels of crude oil (comparable to all the world's known oil reserves) and could last for 600 years. Studies show that the PAHs that are identified in solid fuel emissions react with NO2 to form direct-acting mutagens. In summary, many of the measured genotoxicants found in both the indoor and electricity-generating combustors are the same; therefore, the severity of the health effects vary with exposure and with the health status of the exposed population. Copyright © 2014. Published by Elsevier B.V.

The Paris Agreement zero-emissions goal is not always consistent with the 1.5 °C and 2 °C temperature targets

Science.gov (United States)

Tanaka, Katsumasa; O'Neill, Brian C.

2018-04-01

The Paris Agreement stipulates that global warming be stabilized at well below 2 °C above pre-industrial levels, with aims to further constrain this warming to 1.5 °C. However, it also calls for reducing net anthropogenic greenhouse gas (GHG) emissions to zero during the second half of this century. Here, we use a reduced-form integrated assessment model to examine the consistency between temperature- and emission-based targets. We find that net zero GHG emissions are not necessarily required to remain below 1.5 °C or 2 °C, assuming either target can be achieved without overshoot. With overshoot, however, the emissions goal is consistent with the temperature targets, and substantial negative emissions are associated with reducing warming after it peaks. Temperature targets are put at risk by late achievement of emissions goals and the use of some GHG emission metrics. Refinement of Paris Agreement emissions goals should include a focus on net zero CO2—not GHG—emissions, achieved early in the second half of the century.

No-lose targets as an option to integrate non-Annex I countries in global emission reduction efforts. A game-theoretical analysis

Energy Technology Data Exchange (ETDEWEB)

Duscha, Vicki

2012-07-01

Substantial greenhouse gas emission reductions of 50% and more below 1990 levels by 2050 are necessary, to limit mean temperature increase below 2 C above pre-industrial levels. While the Kyoto Protocol foresees emission reduction targets for Annex I countries only, current and projected greenhouse gas emissions, as well as the growing economic importance of emerging economies call for an integration of non-Annex I countries in global reduction efforts. No-lose targets set emission reduction targets and define incentives for meeting the target, in contrast to binding reduction targets that use penalties to ensure compliance. One form of incentive is the participation in an international emissions trading market. While a few conceptual and quantitative analyses of no-lose targets can be found in the literature, economic analyses have not been carried out so far. In this thesis, two theoretical frameworks are introduced to analyze the potential of no-lose targets to contribute to global emission reduction efforts. First, a two-player, two-stage model is developed to model a non-Annex I country's participation decision and derive the contribution to global emission reductions. Then a two-player participation game is introduced to analyze the effects that the participation decision of one non-Annex I country has on another non-Annex I country also facing a no-lose target. Two market forms, a perfectly competitive market, and a market with market power on the side of the non-Annex I country are analyzed. In order to complement the highly stylized theoretical frameworks, a quantitative analysis applying marginal abatement cost curves is conducted to estimate the contribution of no-lose targets to reaching the 2 C target. The analyses show that no-lose targets can result in substantial contributions from non-Annex I countries to global emission reductions, in particular if the reduction potential in the non-Annex I countries is large, compared to that of the Annex I

Ion emission at the target of the radiographic devices PIVAIR and AIRIX

International Nuclear Information System (INIS)

Compant La Fontaine, A

2007-01-01

On an AIRIX facility, a high-intensity electron beam is used to generate an x-ray pulse for radiographic purposes. The measured electron beam spot size is found to be much larger than its computed value. It is shown that this discrepancy is removed considering ion emission at the target, under electron beam interaction. A model has been developed to simulate the plasma produced during the interaction of the electron beam with the target. The predictions have been compared with ion identification results developed on the PIVAIR prototype accelerator as well as with the x-ray spot size and dose measurements obtained on AIRIX. The simulations show that the ion effect can be reduced by placing a thin foil (100 μm thickness) at an appropriate distance from the target to catch the ions emitted and to stabilize the electron beam spot size. The X-spot size is then reduced, as found experimentally on AIRIX. Moreover, for a smaller thickness barrier foil (5 μm), the ion effect can even be suppressed, producing an X-spot size close to that obtained without ion emission

Effect of kind of solid fuel onto noxious compound emissions in the firing up process of a low output water boiler

International Nuclear Information System (INIS)

Wilk, R.; Szymczyk, J.; Zielinski, Z.; Wystemp, E.

1992-01-01

NO x , SO 2 , CO and polynuclear aromatic hydrocarbon emission tests were carried out during the firing up process of a low output boiler for three kinds of smokeless solid fuels and boiler coal. It has been stated that the use of low emissive fuels in low output boilers did not protect against noxious compound emissions during firing up the boiler. (author). 13 refs, 8 figs, 4 tabs

Greenhouse gas emission and exergy analyses of an integrated trigeneration system driven by a solid oxide fuel cell

International Nuclear Information System (INIS)

Chitsaz, Ata; Mahmoudi, S. Mohammad S.; Rosen, Marc A.

2015-01-01

Exergy and greenhouse gas emission analyses are performed for a novel trigeneration system driven by a solid oxide fuel cell (SOFC). The trigeneration system also consists of a generator-absorber heat exchanger (GAX) absorption refrigeration system and a heat exchanger to produce electrical energy, cooling and heating, respectively. Four operating cases are considered: electrical power generation, electrical power and cooling cogeneration, electrical power and heating cogeneration, and trigeneration. Attention is paid to numerous system and environmental performance parameters, namely, exergy efficiency, exergy destruction rate, and greenhouse gas emissions. A maximum enhancement of 46% is achieved in the exergy efficiency when the SOFC is used as the primary mover for the trigeneration system compared to the case when the SOFC is used as a standalone unit. The main sources of irreversibility are observed to be the air heat exchanger, the SOFC and the afterburner. The unit CO 2 emission (in kg/MWh) is considerably higher for the case in which only electrical power is generated. This parameter is reduced by half when the system is operates in a trigeneration mode. - Highlights: • A novel trigeneration system driven by a solid oxide fuel cell is analyzed. • Exergy and greenhouse gas emission analyses are performed. • Four special cases are considered. • An enhancement of up to 46% is achieved in exergy efficiency. • The CO 2 emission drops to a relatively low value for the tri-generation case

Control of solid tobacco emissions in industrial fact ories applying CDF tools

Directory of Open Access Journals (Sweden)

G Polanco

2016-09-01

Full Text Available The emission of light solid aromatic particles from any tobacco industry affects the surrounding inhabitants, commonly causing allergies and eye irritation and, of course, uncomfortable odours, therefore, these emissions to the air must be regulated. An increasing in production must be considered in the sizing of mechanisms used to achieve the precipitation and final filtration, before discharging to the atmosphere. A numerical tool was applied to study the internal behaviour of low velocity precipitation tunnel and discharge chimney of the refuses treatment system. The characterization of the two-phase flow streamlines allows determining the velocity gradient profiles across the whole tunnel; which is intimately related with the particle concentration, and deposition zones locations. The application of CFD techniques gives the bases to find new design parameters to improve the precipitation tunnel behaviour capability to manage the increment of the mass flow of particles, due to changes in mass cigarette production.

Secondary electron emission from insulators

International Nuclear Information System (INIS)

Kanaya, K.; Ono, S.; Ishigaki, F.

1978-01-01

The high yield of secondary electron emission from insulators due to electron bombardment may be the result of an increase of the depth of escape. The free-electron scattering theory is applied to the high energy of primary beams, but cannot be applied to the low energy of secondary escaping beams because of the large energy gap of the insulators. The plasmon loss with the valence electron is considered when the secondary electrons escape. Based on the energy retardation power formula of the penetration and energy loss of an electron probe into solid targets, secondary electron emissions from insulators are calculated from the assumptions that the distribution of the secondary electrons due to both incident and back-scattered electrons within the target is isotropic and that it follows the absorption law of the Lenard type. The universal yield-energy curve of the secondary electron emission, which is deduced as a function of three parameters such as ionisation potential, valence electron and the back-scattered coefficient in addition to the free-electron density effect, is found to be in good agreement with the experimental results. (author)

The value of advanced technology in meeting 2050 greenhouse gas emissions targets in the United States

International Nuclear Information System (INIS)

Kyle, Page; Clarke, Leon; Pugh, Graham; Wise, Marshall; Calvin, Kate; Edmonds, James; Kim, Son

2009-01-01

This paper, a contribution to the EMF 22 subgroup on Transition Scenarios, examines the relationship between technology evolution over the next 40 years and the cost, energy, and greenhouse gas emissions consequences of possible U.S. mitigation goals. The paper explores these issues within the context of cumulative emissions targets based on linear reductions in CO 2 -e emissions of 50% and 80% below 1990 levels by 2050. Six technology futures were constructed within the MiniCAM integrated assessment model and then applied to the emissions targets. The paper explores the influence of technology availability and expectations of future technology availability on the economic consequences of emissions mitigation, on the time path of emissions mitigation, and on the evolution of the U.S. energy system over time. One of the strongest themes to emerge from the scenarios in this study is that near-term decision-making depends on the availability of technology decades into the future, when deep emissions reductions are required to meet the cumulative emissions goals. In the scenarios in this paper, it is the expectations about future technology that have the most dramatic effect on greenhouse gas emissions prices and emissions reductions in 2020, as opposed to near-term technology availability. Moreover, it is the nature of technology 20, 30, and 40 years out, rather than availability and deployment of technology in the next decade, that will largely determine the character of the mid-century energy system.

Binary-encounter electron emission after fast heavy-ion impact on complex rare- and molecular-gas targets

International Nuclear Information System (INIS)

Bechthold, U.; Ullrich, J.; Ramm, U.; Kraft, G.; Hagmann, S.; Schultz, D.R.; Reinhold, C.O.; Schmidt-Boecking, H.

1998-01-01

Doubly differential cross sections (DDCSs) for electron emission have been measured for collisions of 3.6 MeV/u Ne 10+ , Xe 40+ and 5.9 MeV/u U 29+ on neon, xenon, water, ethanol, methanol, propanol, C 2 F 6 , SF 6 , and C 3 F 8 . Electrons ejected with emission angles between 0 degree and 180 degree with respect to the ion beam axis have been recorded simultaneously using a toroidal electron spectrometer. We analyze the singly differential cross section (SDCS) for binary encounter electron (BEe) production as a function of target electron number and laboratory emission angle. We find that there exists a linear scaling of the BEe SDCS with the number of electrons bound in the target with an energy lower than the reduced projectile energy. The enhancement of BEe production in the forward direction in collisions with partially stripped ions is studied for the different projectiles and targets and compared to theoretical calculations. copyright 1998 The American Physical Society

A green emissive amorphous fac-Alq3 solid generated by grinding crystalline blue fac-Alq3 powder.

Science.gov (United States)

Bi, Hai; Chen, Dong; Li, Di; Yuan, Yang; Xia, Dandan; Zhang, Zuolun; Zhang, Hongyu; Wang, Yue

2011-04-14

A novel green emissive Alq(3) solid with a facial isomeric form has been obtained by grinding the typical blue luminescent fac-Alq(3) crystalline powder. This is the first report, to the best of our knowledge, that a fac-Alq(3) isomer emits green light.

Plasma ion emission from high intensity picosecond laser pulse interactions with solid targets

International Nuclear Information System (INIS)

Fews, A.P.; Norreys, P.A.; Beg, F.N.; Bell, A.R.; Dangor, A.E.; Danson, C.N.; Lee, P.; Rose, S.J.

1994-01-01

The fast ion emission from high intensity, picosecond laser plasmas has been measured to give the characteristic ion energy and the amount of laser energy transferred to ions with energies ≥100 keV/nucleon as a function of incident intensity. The characteristic ion energy varies from 0.2 to 1.3 MeV over the range 2.0x10 17 --2.0x10 18 W cm -2 . Ten percent of the laser energy is transferred into MeV ions at 2.0x10 18 W cm -2 . Calculations of stopping power in high density materials are presented that show that fast ions cannot be ignored in modeling fast ignitor schemes

Phenylalanine-coupled solid lipid nanoparticles for brain tumor targeting

Energy Technology Data Exchange (ETDEWEB)

Kharya, Parul; Jain, Ashish; Gulbake, Arvind; Shilpi, Satish; Jain, Ankit; Hurkat, Pooja [Dr. Hari Singh Gour University, Pharmaceutical Research Projects Laboratory, Department of Pharmaceutical Sciences (India); Majumdar, Subrata [Bose Institute, Division of Molecular Medicine (India); Jain, Sanjay K., E-mail: drskjainin@yahoo.com [Dr. Hari Singh Gour University, Pharmaceutical Research Projects Laboratory, Department of Pharmaceutical Sciences (India)

2013-11-15

The purpose of this study is to investigate the targeting potential of amino acid (phenylalanine)-coupled solid lipid nanoparticles (SLN) loaded with ionically complexed doxorubicin HCl (Dox). Ionic complexation was used to enhance the loading efficiency and release characteristics of water soluble form of Dox. l-Type amino acid transporters (LAT1) are highly expressed on blood brain barrier as well as on many brain cancer cells, thus targeting LAT1 using phenylalanine improved anticancer activity of prepared nanocarrier. The phenylalanine-coupled SLN were characterized by fourier transform infrared spectroscopy, scanning electron microscope, transmission electron microscopy, particle size, zeta potential, entrapment efficiency and in vitro release. The particle size of the resulting SLN was found to be in the range of 163.3 ± 5.2 to 113.0 ± 2.6 nm, with a slightly negative surface charge. In ex vivo study on C6 glioma cell lines, the cellular cytotoxicity of the SLN was highly increased when coupled with phenylalanine. In addition, stealthing sheath of PEG present on the surface of the SLN enhanced the cellular uptake of the SLN on C6 glioma cell line. Results of biodistribution and fluorescence studies clearly revealed that phenylalanine-coupled SLN could deliver high amount of drug into the brain tumor cells and showed the brain-targeting potential.

Uncertain long-run emissions targets, CO{sub 2} price and global energy transition: A general equilibrium approach

Energy Technology Data Exchange (ETDEWEB)

Durand-Lasserve, Olivier, E-mail: olivier.durand@uclouvain.b [Universite Catholique de Louvain (UCL), CORE, Voie du Roman Pays 34, B-1348 Louvain-la-Neuve (Belgium); Pierru, Axel, E-mail: axel.pierru@ifp.f [IFP, Economics Department, 232 Avenue Napoleon Bonaparte, 92852 Rueil-Malmaison (France); Smeers, Yves, E-mail: yves.smeers@uclouvain.ac.b [Universite Catholique de Louvain (UCL), CORE, Voie du Roman Pays 34, B-1348 Louvain-la-Neuve (Belgium)

2010-09-15

The persistent uncertainty about mid-century CO{sub 2} emissions targets is likely to affect not only the technological choices that energy-producing firms will make in the future but also their current investment decisions. We illustrate this effect on CO{sub 2} price and global energy transition within a MERGE-type general-equilibrium model framework, by considering simple stochastic CO{sub 2} policy scenarios. In these scenarios, economic agents know that credible long-run CO{sub 2} emissions targets will be set in 2020, with two possible outcomes: either a 'hard cap' or a 'soft cap'. Each scenario is characterized by the relative probabilities of both possible caps. We derive consistent stochastic trajectories-with two branches after 2020-for prices and quantities of energy commodities and CO{sub 2} emissions permits. The impact of uncertain long-run CO{sub 2} emissions targets on prices and technological trajectories is discussed. In addition, a simple marginal approach allows us to analyze the Hotelling rule with risk premia observed for certain scenarios.

Uncertain long-run emissions targets, CO{sub 2} price and global energy transition. A general equilibrium approach

Energy Technology Data Exchange (ETDEWEB)

Durand-Lasserve, Olivier; Smeers, Yves [Universite Catholique de Louvain (UCL), CORE, Voie du Roman Pays 34, B-1348 Louvain-la-Neuve (Belgium); Pierru, Axel [IFP, Economics Department, 232 Avenue Napoleon Bonaparte, 92852 Rueil-Malmaison (France)

2010-09-15

The persistent uncertainty about mid-century CO{sub 2} emissions targets is likely to affect not only the technological choices that energy-producing firms will make in the future but also their current investment decisions. We illustrate this effect on CO{sub 2} price and global energy transition within a MERGE-type general-equilibrium model framework, by considering simple stochastic CO{sub 2} policy scenarios. In these scenarios, economic agents know that credible long-run CO{sub 2} emissions targets will be set in 2020, with two possible outcomes: either a hard cap or a soft cap. Each scenario is characterized by the relative probabilities of both possible caps. We derive consistent stochastic trajectories - with two branches after 2020 - for prices and quantities of energy commodities and CO{sub 2} emissions permits. The impact of uncertain long-run CO{sub 2} emissions targets on prices and technological trajectories is discussed. In addition, a simple marginal approach allows us to analyze the Hotelling rule with risk premia observed for certain scenarios. (author)

Energy and emission aspects of co-combustion solid recovered fuel with coal in a stoker boiler

Science.gov (United States)

Wasielewski, Ryszard; Głód, Krzysztof; Telenga-Kopyczyńska, Jolanta

2018-01-01

The results of industrial research on co-combustion of solid recovered fuel (SRF) with hard coal in a stoker boiler type WR-25 has been presented. The share of SRF in the fuel mixture was 10%. During the co-combustion of SRF, no technological disturbances or significant reduction in energy efficiency of the boiler were noted. Obtained SO2, NOx and CO emissions were comparable with coal combustion but dust emissions increased. During combustion of the coal mixture with a 10% share of SRF in the test boiler WR-25, the emission standards established for the combustion of the dedicated fuel were met. However, comparison of obtained emission results with the emission standards established for co-incineration of waste, revealed the exceedance of permissible levels of HCl, dust, heavy metals, dioxins and furans. Additionally, the residence time of flue gases in over 850°C conditions for the test boiler WR-25 was too short (1.3 seconds) in refer to the legislative requirements (2 seconds) for the thermal conversion of waste.

Energy and emission aspects of co-combustion solid recovered fuel with coal in a stoker boiler

Directory of Open Access Journals (Sweden)

Wasielewski Ryszard

2018-01-01

Full Text Available The results of industrial research on co-combustion of solid recovered fuel (SRF with hard coal in a stoker boiler type WR-25 has been presented. The share of SRF in the fuel mixture was 10%. During the co-combustion of SRF, no technological disturbances or significant reduction in energy efficiency of the boiler were noted. Obtained SO2, NOx and CO emissions were comparable with coal combustion but dust emissions increased. During combustion of the coal mixture with a 10% share of SRF in the test boiler WR-25, the emission standards established for the combustion of the dedicated fuel were met. However, comparison of obtained emission results with the emission standards established for co-incineration of waste, revealed the exceedance of permissible levels of HCl, dust, heavy metals, dioxins and furans. Additionally, the residence time of flue gases in over 850°C conditions for the test boiler WR-25 was too short (1.3 seconds in refer to the legislative requirements (2 seconds for the thermal conversion of waste.

Environmental and economic effects of the Copenhagen pledges and more ambitious emission reduction targets

International Nuclear Information System (INIS)

Peterson, Everett B.; Schleich, Joachim; Duscha, Vicki

2011-01-01

A multi-region, multi-sector dynamic computable general equilibrium model is applied to explore the economic and welfare effects of the pledges submitted by developed countries (Annex I countries) and major developing (non-Annex I) countries for 2020 under the Copenhagen Accord. In addition to analyzing scenarios reflecting the upper and lower bounds of the Copenhagen Pledges, one additional policy scenario where Annex I countries as a group reduce CO 2 -emissions by 30% in 2020 compared to 1990 levels, and where major non-Annex I countries reduce CO 2 emissions 15% below baseline, is also analyzed. Economic effects are measured as changes in GDP compared to baseline and welfare effects are measured via the equivalent variation. Assuming that countries with emission targets may trade certificates, average reductions in GDP for countries with targets range between 0.1% and 0.7% in 2020 for the policy scenarios. While the GDP losses are larger for major non-Annex I countries with emission targets compared to Annex I countries, this is not the case for the changes in welfare. With the exception of Mexico, the welfare losses for the major non-Annex I regions, as a percentage of projected GDP in 2020, are lower than for the large Annex I countries. - Highlights: → Copenhagen pledges are not ambitious in terms of global CO 2 -emission reductions. → Copenhagen pledges are not costly in terms of global GDP or welfare losses. → Reductions in GDP and welfare in 2020 are not evenly distributed across regions.→ Major non-Annex I countries face relatively larger reductions in GDP compared with Annex I countries.→ Copenhagen pledges do not result in large amounts of carbon leakage.

Neutron measurements from beam-target reactions at the ELISE neutral beam test facility

International Nuclear Information System (INIS)

Xufei, X.; Fan, T.; Nocente, M.; Gorini, G.; Bonomo, F.; Franzen, P.; Fröschle, M.; Grosso, G.; Tardocchi, M.; Grünauer, F.; Pasqualotto, R.

2014-01-01

Measurements of 2.5 MeV neutron emission from beam-target reactions performed at the ELISE neutral beam test facility are presented in this paper. The measurements are used to study the penetration of a deuterium beam in a copper dump, based on the observation of the time evolution of the neutron counting rate from beam-target reactions with a liquid scintillation detector. A calculation based on a local mixing model of deuterium deposition in the target up to a concentration of 20% at saturation is used to evaluate the expected neutron yield for comparison with data. The results are of relevance to understand neutron emission associated to beam penetration in a solid target, with applications to diagnostic systems for the SPIDER and MITICA Neutral Beam Injection prototypes

The central importance of the EU emission trading scheme for achievement of the German climate protection target of 40% until 2020

International Nuclear Information System (INIS)

Hermann, Hauke; Cludius, Johanna

2014-02-01

Both Germany and the European Union have set themselves targets for the reduction of greenhouse gas (GHG) emissions. The EU was the forerunner in 2008 when it adopted the Climate and Energy package and set a target of reducing GHG emissions by 20 % by 2020 compared to 1990. Two years later, Germany adopted a range of national GHG targets in the context of the German government's Energy Concept. This includes a 40% emissions reduction target to be met by 2020. One of the main instruments for achieving GHG emissions reduction targets is the EU Emissions Trading Scheme (EU ETS), which covers all large industrial and combustion installations in Europe. According to the agreement made in 2008 (Climate and Energy Package), the effort to achieve the EU's 20 % reduction target by 2020 was split between the ETS sector (2/3 of the reduction effort, representing a 21 % reduction in GHG emissions for installations covered under the ETS compared to 2005) and the non-ETS sector (1/3 of the reduction effort, representing a 10 % reduction compared to 2005). Logically, GHG emissions reductions occurring in German ETS installations count both towards the EU and the national target. This research project has been commissioned to analyse whether the ETS in its cur-rent design can contribute its fair share in efforts to meet the national emissions reduc-tion target. This question is particularly relevant in light of the following considerations: - The new German Coalition Agreement, signed in December 2013, reiterated the national target of a 40 % reduction of GHG emissions by 2020 compared to 1990 levels. - At the same time, the new Coalition Agreement stated that changes to the ETS are only to be considered if the EU GHG emissions reduction target will not be met. - There is a surplus of CO2 allowances on the ETS market, which undermines the credibility of the instrument as well as the integrity of the emissions reduction tar-gets (both European and national). At the same time, the

Plasma Immersion Ion Implantation with Solid Targets for Space and Aerospace Applications

International Nuclear Information System (INIS)

Oliveira, R. M.; Goncalves, J. A. N.; Ueda, M.; Silva, G.; Baba, K.

2009-01-01

This paper describes successful results obtained by a new type of plasma source, named as Vaporization of Solid Targets (VAST), for treatment of materials for space and aerospace applications, by means of plasma immersion ion implantation and deposition (PIII and D). Here, the solid element is vaporized in a high pressure glow discharge, being further ionized and implanted/deposited in a low pressure cycle, with the aid of an extra electrode. First experiments in VAST were run using lithium as the solid target. Samples of silicon and aluminum alloy (2024) were immersed into highly ionized lithium plasma, whose density was measured by a double Langmuir probe. Measurements performed with scanning electron microscopy (SEM) showed clear modification of the cross-sectioned treated silicon samples. X-ray photoelectron spectroscopy (XPS) analysis revealed that lithium was implanted/deposited into/onto the surface of the silicon. Implantation depth profiles may vary according to the condition of operation of VAST. One direct application of this treatment concerns the protection against radiation damage for silicon solar cells. For the case of the aluminum alloy, X-ray diffraction analysis indicated the appearance of prominent new peaks. Surface modification of A12024 by lithium implantation/deposition can lower the coefficient of friction and improve the resistance to fatigue of this alloy. Recently, cadmium was vaporized and ionized in VAST. The main benefit of this element is associated with the improvement of corrosion resistance of metallic substrates. Besides lithium and cadmium, VAST allows to performing PIII and D with other species, leading to the modification of the near-surface of materials for distinct purposes, including applications in the space and aerospace areas.

Modelling the impacts of challenging 2020 non-ETS GHG emissions reduction targets on Ireland′s energy system

International Nuclear Information System (INIS)

Chiodi, Alessandro; Gargiulo, Maurizio; Deane, J.P.; Lavigne, Denis; Rout, Ullash K.; Ó Gallachóir, Brian P.

2013-01-01

This paper focuses on Ireland's ambitious target for 2020 to reduce greenhouse gas (GHG) emissions by 20% below 2005 levels for sectors not covered by ETS (Non-ETS). Ireland is an interesting case study due to the role of agriculture (a particularly challenging sector with regard to GHG emissions reduction), that represents 29% of Ireland's GHG emissions compared with less than 10% for the EU. The analysis is carried out with the Irish TIMES model, a bottom-up energy systems modelling tool with detailed characterization of Ireland's energy system. The paper uses scenario analysis to provide pathways that demonstrate how Ireland can meet the non-ETS target at least cost. The paper considers the impacts (in terms of different technology choices and higher marginal abatement costs) arising from higher targets for the energy system to compensate for growth in agriculture activity and low mitigation potential in that sector. The results point to a need to reconsider Ireland's renewable energy focus, with a need for increased effort in renewable transport and renewable heat in particular. The results also point to significant electrification of residential heating. The results also point to a high marginal abatement cost (€213/tCO 2 ), which challenges the analysis carried out at EU level to establish Ireland's non-ETS target. - Highlights: • Techno-economic energy model to deliver EU GHG mitigation target by 2020 in Ireland. • Agriculture represents nearly half of Non-ETS emissions in Ireland. • The target set for Non-ETS GHG for Ireland is far from a cost optimal target. • The results point to a need to reconsider Ireland's renewable energy focus. • Key pathways: electrification of heating in buildings and biofuels in transport

Mercury emissions from municipal solid waste combustors. An assessment of the current situation in the United States and forecast of future emissions

Energy Technology Data Exchange (ETDEWEB)

None

1993-05-01

This report examines emissions of mercury (Hg) from municipal solid waste (MSW) combustion in the United States (US). It is projected that total annual nationwide MSW combustor emissions of mercury could decrease from about 97 tonnes (1989 baseline uncontrolled emissions) to less than about 4 tonnes in the year 2000. This represents approximately a 95 percent reduction in the amount of mercury emitted from combusted MSW compared to the 1989 mercury emissions baseline. The likelihood that routinely achievable mercury emissions removal efficiencies of about 80 percent or more can be assured; it is estimated that MSW combustors in the US could prove to be a comparatively minor source of mercury emissions after about 1995. This forecast assumes that diligent measures to control mercury emissions, such as via use of supplemental control technologies (e.g., carbon adsorption), are generally employed at that time. However, no present consensus was found that such emissions control measures can be implemented industry-wide in the US within this time frame. Although the availability of technology is apparently not a limiting factor, practical implementation of necessary control technology may be limited by administrative constraints and other considerations (e.g., planning, budgeting, regulatory compliance requirements, etc.). These projections assume that: (a) about 80 percent mercury emissions reduction control efficiency is achieved with air pollution control equipment likely to be employed by that time; (b) most cylinder-shaped mercury-zinc (CSMZ) batteries used in hospital applications can be prevented from being disposed into the MSW stream or are replaced with alternative batteries that do not contain mercury; and (c) either the amount of mercury used in fluorescent lamps is decreased to an industry-wide average of about 27 milligrams of mercury per lamp or extensive diversion from the MSW stream of fluorescent lamps that contain mercury is accomplished.

Targeting doxorubicin encapsulated in stealth liposomes to solid tumors by non thermal diode laser.

Science.gov (United States)

Ghannam, Magdy M; El Gebaly, Reem; Fadel, Maha

2016-04-05

The use of liposomes as drug delivery systems is the most promising technique for targeting drug especially for anticancer therapy. In this study sterically stabilized liposomes was prepared from DPPC/Cholesterol/PEG-PE encapsulated doxorubicin. The effect of lyophilization on liposomal stability and hence expiration date were studied. Moreover, the effect of diode laser on the drug released from liposomesin vitro and in vivo in mice carrying implanted solid tumor were also studied. The results indicated that lyophilization of the prepared liposomes encapsulating doxorubicin led to marked stability when stored at 5 °C and it is possible to use the re-hydrated lyophilized liposomes within 12 days post reconstitution. Moreover, the use of low energy diode laser for targeting anticancer drug to the tumor cells is a promising method in cancer therapy. We can conclude that lyophilization of the liposomes encapsulating doxorubicin lead to marked stability for the liposomes when stored at 5 °C. Moreover, the use of low energy diode laser for targeting anticancer drug to the tumor cells through the use of photosensitive sterically stabilized liposomes loaded with doxorubicin is a promising method. It proved to be applicable and successful for treatment of Ehrlich solid tumors implanted in mice and eliminated toxic side effects of doxorubicin.

Energy and emissions benefits of renewable energy derived from municipal solid waste: Analysis of a low carbon scenario in Malaysia

International Nuclear Information System (INIS)

Tan, Sie Ting; Hashim, Haslenda; Lim, Jeng Shiun; Ho, Wai Shin; Lee, Chew Tin; Yan, Jinyue

2014-01-01

Highlights: • Feasibility study on the energy and GHG emission reduction for WtE strategies for municipal solid waste (MSW) in Malaysia. • Greenhouse gases (GHG) emissions from WtE strategies analysed using IPCC guideline. • Scenario analysis by comparison of different WtE strategies. • Impact of moisture content of MSW towards energy potential and GHG emission reduction. - Abstract: Ineffective waste management that involves dumping of waste in landfills may degrade valuable land resources and emit methane gas (CH 4 ), a more potent greenhouse gas than carbon dioxide (CO 2 ). The incineration of waste also emits polluted chemicals such as dioxin and particle. Therefore, from a solid waste management perspective, both landfilling and incineration practices pose challenges to the development of a green and sustainable future. Waste-to-energy (WtE) has become a promising strategy catering to these issues because the utilisation of waste reduces the amount of landfilled waste (overcoming land resource issues) while increasing renewable energy production. The goal of this paper is to evaluate the energy and carbon reduction potential in Malaysia for various WtE strategies for municipal solid waste (MSW). The material properties of the MSW, its energy conversion potential and subsequent greenhouse gases (GHG) emissions are analysed based on the chemical compositions and biogenic carbon fractions of the waste. The GHG emission reduction potential is also calculated by considering fossil fuel displacement and CH 4 avoidance from landfilling. In this paper, five different scenarios are analysed with results indicating a integration of landfill gas (LFG) recovery systems and waste incinerator as the major and minor WtE strategies shows the highest economical benefit with optimal GHG mitigation and energy potential. Sensitivity analysis on the effect of moisture content of MSW towards energy potential and GHG emissions are performed. These evaluations of Wt

Secondary electrons as probe of preequilibrium stopping power of ions penetrating solids

International Nuclear Information System (INIS)

Kroneberger, K.; Rothard, H.; Koschar, P.; Lorenzen, P.; Groeneveld, K.O.; Clouvas, A.; Veje, E.; Kemmler, J.

1990-01-01

The passage of ions through solid media is accompanied by the emission of low energy secondary electrons. At high ion velocities v p (i.e. v p > 10 7 cm/s) the kinetic emission of electrons as a result of direct Coulomb interaction between the ion and the target electron is the dominant initial production mechanism. The energy lost by the ion and, thus, transferred to the electrons is known as electronic stopping power in the solid. Elastic and inelastic interactions of primary, liberated electrons on their way through the bulk and the surface of the solid modify strongly their original energy and angular distribution and, in particular, leads to the transfer of their energy to further, i.e. secondary electrons (SE), such that the main part of the deposited energy of the ion is eventually over transferred to SE. It is, therefore, suggestive to assume a proportionality between the electronic stopping power S sm-bullet of the ion and the total SE yield g, i.e. the number of electrons ejected per ion. Following Sternglass the authors consider schematically for kinetic SE emission contributions from two extreme cases: (a) SEs produced mostly isotropically with large impact parameter, associated with an escape depth L SE from the solid; (b) SEs produced mostly unisotropically in forward direction with small impact parameter (δ-electrons), associated with a transport length L δ

Supercritical fluid extraction of positron-emitting radioisotopes from solid target matrices

International Nuclear Information System (INIS)

Schlyer, D.

2000-01-01

Supercritical fluids are attractive as media for both chemical reactions, as well as process extraction, since their physical properties can be manipulated by small changes in pressure and temperature near the critical point of the fluid. Such changes can result in drastic effects on density-dependent properties such as solubility, refractive index, dielectric constant, viscosity and diffusivity of the fluid. This suggests that pressure tuning of a pure supercritical fluid may be a useful means to manipulate chemical reactions on the basis of a thermodynamic solvent effect. It also means that the solvation properties of the fluid can be precisely controlled to enable selective component extraction from a matrix. In recent years there has been a growing interest in applying supercritical fluid extraction to the selective removal of trace metals from solid samples. Much of the work has been done on simple systems comprised of inert matrices such as silica or cellulose. Recently, this process as been expanded to environmental samples as well. However, very little is understood about the exact mechanism of the extraction process. Of course, the widespread application of this technology is highly dependent on the ability of scientists to model and predict accurate phase equilibria in complex systems. In this project, we plan to explore the feasibility of utilizing supercritical fluids as solvents for reaction and extraction of radioisotopes produced from solid enriched targets. The reason for this work is that many of these enriched target materials used for radioisotope production are expensive

Modelling greenhouse gas emissions for municipal solid waste management strategies in Ottawa, Ontario, Canada

Energy Technology Data Exchange (ETDEWEB)

Mohareb, Adrian K. [Technology Early Action Measures (TEAM) Office, 55 Murray Street, Suite 230, Ottawa, ON (Canada); Warith, Mostafa A.; Diaz, Rodrigo [Department of Civil Engineering, Ryerson University, 350 Victoria Street, Toronto, ON (Canada)

2008-09-15

Human-induced climate change, through the emission of greenhouse gases, may result in a significant negative impact on Earth. Canada is one of the largest per capita emitters of greenhouse gas, generating 720 megatonnes (Mt) carbon dioxide equivalents (CO{sub 2}e), or per capita emissions of 23.2 t CO{sub 2}e. The solid waste sector in Canada was directly responsible for 25 Mt CO{sub 2}e in 2001, of which 23 Mt CO{sub 2}e were produced by landfill gas (LFG). A modelling exercise was undertaken to determine greenhouse gas (GHG) emissions from the waste sector using the waste disposal, recycling, and composting data from Ottawa, Ontario, Canada for the year 2003, as well as the results of an audit of residential units performed in the same year. This evaluation determined that, among the options examined, waste incineration, further source separation of recyclables, and anaerobic digestion of an organic wastes have the greatest benefits for reducing GHG emissions in the City of Ottawa's waste sector. Challenges surrounding the installation of incineration facilities in Canada suggest that improved diversion of recyclable materials and anaerobic digestion of organic materials are the optimal options for the City of Ottawa to pursue. (author)

Analysis of potential for reducing emissions of greenhouse gases in municipal solid waste in Brazil, in the state and city of Rio de Janeiro

International Nuclear Information System (INIS)

Loureiro, S.M.; Rovere, E.L.L.; Mahler, C.F.

2013-01-01

Highlights: ► We constructed future scenarios of emissions of greenhouse gases in waste. ► Was used the IPCC methodology for calculating emission inventories. ► We calculated the costs of abatement for emissions reduction in landfill waste. ► The results were compared to Brazil, state and city of Rio de Janeiro. ► The higher the environmental passive, the greater the possibility of use of biogas. - Abstract: This paper examines potential changes in solid waste policies for the reduction in GHG for the country of Brazil and one of its major states and cities, Rio de Janeiro, from 2005 to 2030. To examine these policy options, trends in solid waste quantities and associated GHG emissions are derived. Three alternative policy scenarios are evaluated in terms of effectiveness, technology, and economics and conclusions posited regarding optimal strategies for Brazil to implement. These scenarios are been building on the guidelines for national inventories of GHG emissions (IPCC, 2006) and adapted to Brazilian states and municipalities’ boundaries. Based on the results, it is possible to say that the potential revenue from products of solid waste management is more than sufficient to transform the current scenario in this country into one of financial and environmental gains, where the negative impacts of climate change have created a huge opportunity to expand infrastructure for waste management

Density effects in heavy ion charge-exchange processes in gaseous and solid targets

International Nuclear Information System (INIS)

Teplova, Ya.A.; Dmitriev, I.S.; Belkova, Yu.A.

2000-01-01

Experimental results on the pre-equilibrium and equilibrium charge distributions in celluloid films for incident Be, B, C, N, O ions are analyzed in order to obtain charge-exchange cross-sections. The determined 'effective' cross-sections of electron capture and loss in celluloid together with earlier measured analogous cross-sections in nitrogen allow us to calculate charge fractions F i (t) depending on the target thickness in solid (celluloid) and gaseous (nitrogen) matter. The absolute values and the ratios A cap =σ g i,i-1 /σ s i,i-1 and A loss =σ g i-1,i /σ s i-1,i of electron capture and loss cross-sections in {s} solids (celluloid, carbon) and {g} gases (nitrogen) are under consideration

Design Optimisation of a High Intensity Beam Facility and Feasibility Experiment of a Solid Fragmented Target

CERN Document Server

Charitonidis, Nikolaos; Rivkin, Leonid

2014-06-13

The present PhD thesis describes the design, execution and results of the HRMT-10 experiment performed at the HiRadMat facility of the CERN/SPS complex. The first part of the thesis covers the design optimization studies of the HiRadMat facility, focusing in particular on the radiation protection issues. A detailed Monte-Carlo model of the facility has been developed and validated through comparison with measurements. A very satisfactory agreement between the simulation and the experimental data is observed. In the second part of this thesis, a novel feasibility experiment of a fragmented solid target for a future Neutrino Factory or a Super Beam facility, able to support high beam powers ( 1 MW) is presented in detail. A solid granular target has been proposed as an interesting alternative to an open Hg jet target, presently considered as the baseline for such facilities, but posing considerable technical challenges. The HRMT-10 experiment seeks to address the lack of experimental data of the feasibility of...

Solid targets for production of radioisotopes with cyclotron; Blancos solidos para produccion de radioisotopos con ciclotron

Energy Technology Data Exchange (ETDEWEB)

Paredes G, L.; Balcazar G, M. [Instituto Nacional de Investigaciones Nucleares, Direccion de Investigacion Tecnologica, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

1999-07-01

The design of targets for production of radioisotopes and radiopharmaceuticals of cyclotron to medical applications requires a detailed analysis of several variables such as: cyclotron operation conditions, choice of used materials as target and their physicochemical characteristics, activity calculation, the yielding of each radioisotope by irradiation, the competition of nuclear reactions in function of the projectiles energy and the collision processes amongst others. The objective of this work is to determine the equations for the calculation for yielding of solid targets at the end of the proton irradiation. (Author)

Emissions of polychlorinated diphenyl ethers from a municipal solid waste incinerator during the start-up operation

International Nuclear Information System (INIS)

Yang, Jing-Sing; Lin, Sheng-Lun; Lin, Ta-Chang; Wu, Yee-Lin; Wang, Lin-Chi; Chang-Chien, Guo-Ping

2015-01-01

Highlights: • This is the first study on the PCDE emission during a MSWI start-up procedure. • The highest PCDE level occurred similar to the PCDD/F reformation temperature. • The pollution control were modified and reduce 86% PCDE peak emission. • Multiple start-ups are analyzed for their effects on the annual PCDE emission. - Abstract: This study examines the emissions of polychlorinated diphenyl ethers (PCDEs) during the start-up processes of a municipal solid waste incinerator (MSWI). Both normal and modified emission control start-ups were tested. Fifteen samples were taken from the flue gas with increasing furnace temperature. Peak PCDE concentrations of 1.48–10.3 ng/Nm 3 were observed at 8–11 h after the start of combustion, when the furnace temperature was in the range of 267–440 °C, that also needed for PCDD/F formation by de novo synthesis. The PCDE emissions could thus, be reduced by current control techniques. Furthermore, the modified control strategies inhibited PCDE formation at the beginning of combustion, and led to an 86% reduction in the maximum PCDE concentration. The overall start-up emissions were calculated as 1.01–3.08 mg, while the annual PCDE emissions with one start-up operation were found to be 7.48–9.64 mg. However, total PCDE emissions will increase by 12–69% if the number of start-up runs increases to between two and eight times per year. Consequently, the prevention of the unnecessary start-ups and advanced activation of the related emission control system are both efficient ways to reduce PCDE emissions.

Emissions of polychlorinated diphenyl ethers from a municipal solid waste incinerator during the start-up operation

Energy Technology Data Exchange (ETDEWEB)

Yang, Jing-Sing [Department of Environmental Engineering, National Cheng Kung University, Tainan 70101, Taiwan (China); Lin, Sheng-Lun, E-mail: cbmsgml@gmail.com [Department of Civil Engineering and Geomatics, Cheng Shiu University, Kaohsiung 83347, Taiwan (China); Super Micro Mass Research and Technology Center, Cheng Shiu University, Kaohsiung 83347, Taiwan (China); Lin, Ta-Chang; Wu, Yee-Lin [Department of Environmental Engineering, National Cheng Kung University, Tainan 70101, Taiwan (China); Wang, Lin-Chi [Department of Civil Engineering and Geomatics, Cheng Shiu University, Kaohsiung 83347, Taiwan (China); Chang-Chien, Guo-Ping, E-mail: guoping@csu.edu.tw [Super Micro Mass Research and Technology Center, Cheng Shiu University, Kaohsiung 83347, Taiwan (China); Department of Cosmetic and Fashion Styling, Kaohsiung 83347, Taiwan (China)

2015-12-15

Highlights: • This is the first study on the PCDE emission during a MSWI start-up procedure. • The highest PCDE level occurred similar to the PCDD/F reformation temperature. • The pollution control were modified and reduce 86% PCDE peak emission. • Multiple start-ups are analyzed for their effects on the annual PCDE emission. - Abstract: This study examines the emissions of polychlorinated diphenyl ethers (PCDEs) during the start-up processes of a municipal solid waste incinerator (MSWI). Both normal and modified emission control start-ups were tested. Fifteen samples were taken from the flue gas with increasing furnace temperature. Peak PCDE concentrations of 1.48–10.3 ng/Nm{sup 3} were observed at 8–11 h after the start of combustion, when the furnace temperature was in the range of 267–440 °C, that also needed for PCDD/F formation by de novo synthesis. The PCDE emissions could thus, be reduced by current control techniques. Furthermore, the modified control strategies inhibited PCDE formation at the beginning of combustion, and led to an 86% reduction in the maximum PCDE concentration. The overall start-up emissions were calculated as 1.01–3.08 mg, while the annual PCDE emissions with one start-up operation were found to be 7.48–9.64 mg. However, total PCDE emissions will increase by 12–69% if the number of start-up runs increases to between two and eight times per year. Consequently, the prevention of the unnecessary start-ups and advanced activation of the related emission control system are both efficient ways to reduce PCDE emissions.

Combined-modality treatment of solid tumors using radiotherapy and molecular targeted agents.

Science.gov (United States)

Ma, Brigette B Y; Bristow, Robert G; Kim, John; Siu, Lillian L

2003-07-15

Molecular targeted agents have been combined with radiotherapy (RT) in recent clinical trials in an effort to optimize the therapeutic index of RT. The appeal of this strategy lies in their potential target specificity and clinically acceptable toxicity. This article integrates the salient, published research findings into the underlying molecular mechanisms, preclinical efficacy, and clinical applicability of combining RT with molecular targeted agents. These agents include inhibitors of intracellular signal transduction molecules, modulators of apoptosis, inhibitors of cell cycle checkpoints control, antiangiogenic agents, and cyclo-oxygenase-2 inhibitors. Molecular targeted agents can have direct effects on the cytoprotective and cytotoxic pathways implicated in the cellular response to ionizing radiation (IR). These pathways involve cellular proliferation, DNA repair, cell cycle progression, nuclear transcription, tumor angiogenesis, and prostanoid-associated inflammation. These pathways can also converge to alter RT-induced apoptosis, terminal growth arrest, and reproductive cell death. Pharmacologic modulation of these pathways may potentially enhance tumor response to RT though inhibition of tumor repopulation, improvement of tumor oxygenation, redistribution during the cell cycle, and alteration of intrinsic tumor radiosensitivity. Combining RT and molecular targeted agents is a rational approach in the treatment of solid tumors. Translation of this approach from promising preclinical data to clinical trials is actively underway.

The Emission, Lifetimes, and Formation Threshold of the Vegard-Kaplan Transition of Solid Nitrogen Exposed to Far-ultraviolet Radiation

Science.gov (United States)

Lu, Hsiao-Chi; Lo, Jen-Iu; Peng, Yu-Chain; Chou, Sheng-Lung; Lin, Meng-Yeh; Cheng, Bing-Ming

2016-11-01

Irradiation of solid nitrogen at 4 K with far-ultraviolet light from a synchrotron caused excitation to the upper state of the Vegard-Kaplan (VK) system; the emission in that system was simultaneously recorded in wavelength region 200-440 nm. The lifetimes of emission lines for VK (0, 1) to (0, 12) transitions were measured in the range of 2.12 ˜ 2.65 s. The threshold wavelength to observe the VK emission was 175.0 ± 3.5 nm, corresponding to energy 7.08 ± 0.14 eV. This investigation of the generation of icy VK nitrogen enhances our understanding of its photochemistry in space.

THE EMISSION, LIFETIMES, AND FORMATION THRESHOLD OF THE VEGARD–KAPLAN TRANSITION OF SOLID NITROGEN EXPOSED TO FAR-ULTRAVIOLET RADIATION

Energy Technology Data Exchange (ETDEWEB)

Lu, Hsiao-Chi; Lo, Jen-Iu; Peng, Yu-Chain; Chou, Sheng-Lung; Lin, Meng-Yeh; Cheng, Bing-Ming, E-mail: bmcheng@nsrrc.org.tw [National Synchrotron Radiation Research Center, No. 101, Hsin-Ann Road, Hsinchu Science Park, Hsinchu 30076, Taiwan (China)

2016-11-20

Irradiation of solid nitrogen at 4 K with far-ultraviolet light from a synchrotron caused excitation to the upper state of the Vegard–Kaplan (VK) system; the emission in that system was simultaneously recorded in wavelength region 200–440 nm. The lifetimes of emission lines for VK (0, 1) to (0, 12) transitions were measured in the range of 2.12 ∼ 2.65 s. The threshold wavelength to observe the VK emission was 175.0 ± 3.5 nm, corresponding to energy 7.08 ± 0.14 eV. This investigation of the generation of icy VK nitrogen enhances our understanding of its photochemistry in space.

THE EMISSION, LIFETIMES, AND FORMATION THRESHOLD OF THE VEGARD–KAPLAN TRANSITION OF SOLID NITROGEN EXPOSED TO FAR-ULTRAVIOLET RADIATION

International Nuclear Information System (INIS)

Lu, Hsiao-Chi; Lo, Jen-Iu; Peng, Yu-Chain; Chou, Sheng-Lung; Lin, Meng-Yeh; Cheng, Bing-Ming

2016-01-01

Irradiation of solid nitrogen at 4 K with far-ultraviolet light from a synchrotron caused excitation to the upper state of the Vegard–Kaplan (VK) system; the emission in that system was simultaneously recorded in wavelength region 200–440 nm. The lifetimes of emission lines for VK (0, 1) to (0, 12) transitions were measured in the range of 2.12 ∼ 2.65 s. The threshold wavelength to observe the VK emission was 175.0 ± 3.5 nm, corresponding to energy 7.08 ± 0.14 eV. This investigation of the generation of icy VK nitrogen enhances our understanding of its photochemistry in space.

Commercial and Industrial Solid Waste Incineration Units (CISWI): New Source Performance Standards (NSPS) and Emission Guidelines (EG) for Existing Sources

Science.gov (United States)

Learn about the New Source Performance Standards (NSPS) for commercial and industrial solid waste incineration (CISWI) units including emission guidelines and compliance times for the rule. Read the rule history and summary, and find supporting documents

Modified emission-transmission method for determining trace elements in solid samples using the XRF techniques

International Nuclear Information System (INIS)

Poblete, V.; Alvarez, M.; Hermosilla, M.

2000-01-01

This is a study of an analysis of trace elements in medium thick solid samples, by the modified transmission emission method, using the energy dispersion X-ray fluorescence technique (EDXRF). The effects of absorption and reinforcement are the main disadvantages of the EDXRF technique for the quantitative analysis of bigger elements and trace elements in solid samples. The implementation of this method and its application to a variety of samples was carried out using an infinitely thick multi-element white sample that calculates the correction factors by absorbing all the analytes in the sample. The discontinuities in the masic absorption coefficients versus energies association for each element, with medium thick and homogenous samples, are analyzed and corrected. A thorough analysis of the different theoretical and test variables are proven by using real samples, including certified material with known concentration. The simplicity of the calculation method and the results obtained show the method's major precision, with possibilities for the non-destructive routine analysis of different solid samples, using the EDXRF technique (author)

X-ray emission characteristics of foam target plasmas

International Nuclear Information System (INIS)

Fronya, A.A.; Borisenko, N.G.; Chernodub, M.L.; Merkuliev, Yu.A.; Osipov, M.V.; Puzyrev, V.N.; Sahakyan, A.T.; Starodub, A.N.; Vasin, B.L.; Yakushev, O.F.

2010-01-01

Complete text of publication follows. Experimental results of laser radiation interaction with a foam targets are presented. The spatial, temporal and energy characteristics of x-ray plasma radiation have been investigated. The pinhole-camera and Schwarzschild objective have been used for the plasma image formation in different spectral ranges. The plasma image is registered by the Schwarzschild objective in a narrow spectral range 180 - 200 A. Spectral characteristics of x-ray radiation registered by pinhole-camera have been defined by means outer filters. The use of the filters with different transmission curves allowed one the determine the localization of x-ray radiation with fixed wavelength. Spatial resolution accounts 16 μm in the pinhole-camera diagnostic channel and 2.5 μm in the Schwarzschild objective diagnostic channel. The plasma images in the intrinsic x-ray radiation show that the emission area in the transverse direction with respect to the direction of the propagating heating radiation exceeds the focal spot size. This fact indicates that the target heating in the transverse direction is due to internal energy of the created plasma. The average value of plasma electron temperature is ∼ 0.4 - 1.4 keV. Acknowledgements. The work is partly supported by the Russian Foundation for Basic Researches, grant no. 10-02-00113 and by Federal Target Program 'Research and scientific-pedagogical cadres of Innovative Russia' (grant 2009-1.1-122-052-025).

The estimation of N2O emissions from municipal solid waste incineration facilities: The Korea case

International Nuclear Information System (INIS)

Park, Sangwon; Choi, Jun-Ho; Park, Jinwon

2011-01-01

The greenhouse gases (GHGs) generated in municipal solid waste (MSW) incineration are carbon dioxide (CO 2 ), methane (CH 4 ), and nitrous oxide (N 2 O). In South Korea case, the total of GHGs from the waste incineration facilities has been increasing at an annual rate 10%. In these view, waste incineration facilities should consider to reduce GHG emissions. This study is designed to estimate the N 2 O emission factors from MSW incineration plants, and calculate the N 2 O emissions based on these factors. The three MSW incinerators examined in this study were either stoker or both stoker and rotary kiln facilities. The N 2 O concentrations from the MSW incinerators were measured using gas chromatography-electron capture detection (GC-ECD) equipment. The average of the N 2 O emission factors for the M01 plant, M02 plant, and M03 plant are 71, 75, and 153 g-N 2 O/ton-waste, respectively. These results showed a significant difference from the default values of the intergovernmental panel on climate change (IPCC), while approaching those values derived in Japan and Germany. Furthermore, comparing the results of this study to the Korea Energy Economics Institute (KEEI) (2007) data on waste incineration, N 2 O emissions from MSW incineration comprised 19% of the total N 2 O emissions.

The estimation of N2O emissions from municipal solid waste incineration facilities: The Korea case.

Science.gov (United States)

Park, Sangwon; Choi, Jun-Ho; Park, Jinwon

2011-08-01

The greenhouse gases (GHGs) generated in municipal solid waste (MSW) incineration are carbon dioxide (CO(2)), methane (CH(4)), and nitrous oxide (N(2)O). In South Korea case, the total of GHGs from the waste incineration facilities has been increasing at an annual rate 10%. In these view, waste incineration facilities should consider to reduce GHG emissions. This study is designed to estimate the N(2)O emission factors from MSW incineration plants, and calculate the N(2)O emissions based on these factors. The three MSW incinerators examined in this study were either stoker or both stoker and rotary kiln facilities. The N(2)O concentrations from the MSW incinerators were measured using gas chromatography-electron capture detection (GC-ECD) equipment. The average of the N(2)O emission factors for the M01 plant, M02 plant, and M03 plant are 71, 75, and 153g-N(2)O/ton-waste, respectively. These results showed a significant difference from the default values of the intergovernmental panel on climate change (IPCC), while approaching those values derived in Japan and Germany. Furthermore, comparing the results of this study to the Korea Energy Economics Institute (KEEI) (2007) data on waste incineration, N(2)O emissions from MSW incineration comprised 19% of the total N(2)O emissions. Crown Copyright © 2011. Published by Elsevier Ltd. All rights reserved.

High-resolution multi-MeV x-ray radiography using relativistic laser-solid interaction

International Nuclear Information System (INIS)

Courtois, C.; Compant La Fontaine, A.; Barbotin, M.; Bazzoli, S.; Brebion, D.; Bourgade, J. L.; Gazave, J.; Lagrange, J. M.; Landoas, O.; Le Dain, L.; Lefebvre, E.; Pichoff, N.; Edwards, R.; Aedy, C.; Biddle, L.; Drew, D.; Gardner, M.; Ramsay, M.; Simons, A.; Sircombe, N.

2011-01-01

When high intensity (≥10 19 W cm -2 ) laser light interacts with matter, multi-MeV electrons are produced. These electrons can be utilized to generate a MeV bremsstrahlung x-ray emission spectrum as they propagate into a high-Z solid target positioned behind the interaction area. The short duration ( 2 ) object is then performed with few hundred microns spatial resolution.

Solid Polarized Targets and Applications

International Nuclear Information System (INIS)

Crabb, D. G.

2008-01-01

Examples are given of dynamically polarized targets in use today and how the subsystems have changed to meet the needs of todays experiments. Particular emphasis is placed on target materials such as ammonia and lithium deuteride. Recent polarization studies of irradiated materials such as butanol, deuterated butanol, polyethylene, and deuterated polyethylene are presented. The operation of two non-DNP target systems as well as applications of traditional DNP targets are briefly discussed

Response of Solid and Liquid Targets to High Power Proton Beams for Neutrino Factories

CERN Document Server

Sievers, P

2000-01-01

The response of solid and liquid targets to rapid heating by the incident proton beam is assessed in a classical way, among other things by solving the wave equation under linear conditions and in cylindrical symmetry. This study provides bench mark values and allows to identify critical issues and limiting factors which can help to guide further investigations with more sophisticated means.

Estimated refractive index and solid density of DT, with application to hollow-microsphere laser targets

International Nuclear Information System (INIS)

Briggs, C.K.; Tsugawa, R.T.; Hendricks, C.D.; Souers, P.C.

1975-01-01

The literature values for the 0.55-μm refractive index N of liquid and gaseous H 2 and D 2 are combined to yield the equation (N - 1) = [(3.15 +- 0.12) x 10 -6 ]rho, where rho is the density in moles per cubic meter. This equation can be extrapolated to 300 0 K for use on DT in solid, liquid, and gas phases. The equation is based on a review of solid-hydrogen densities measured in bulk and also by diffraction methods. By extrapolation, the estimated densities and 0.55-μm refractive indices for DT are given. Radiation-induced point defects could possibly cause optical absorption and a resulting increased refractive index in solid DT and T 2 . The effect of the DT refractive index in measuring glass and cryogenic DT laser targets is also described

Global reverse supply chain design for solid waste recycling under uncertainties and carbon emission constraint.

Science.gov (United States)

Xu, Zhitao; Elomri, Adel; Pokharel, Shaligram; Zhang, Qin; Ming, X G; Liu, Wenjie

2017-06-01

The emergence of concerns over environmental protection, resource conservation as well as the development of logistics operations and manufacturing technology has led several countries to implement formal collection and recycling systems of solid waste. Such recycling system has the benefits of reducing environmental pollution, boosting the economy by creating new jobs, and generating income from trading the recyclable materials. This leads to the formation of a global reverse supply chain (GRSC) of solid waste. In this paper, we investigate the design of such a GRSC with a special emphasis on three aspects; (1) uncertainty of waste collection levels, (2) associated carbon emissions, and (3) challenges posed by the supply chain's global aspect, particularly the maritime transportation costs and currency exchange rates. To the best of our knowledge, this paper is the first attempt to integrate the three above-mentioned important aspects in the design of a GRSC. We have used mixed integer-linear programming method along with robust optimization to develop the model which is validated using a sample case study of e-waste management. Our results show that using a robust model by taking the complex interactions characterizing global reverse supply chain networks into account, we can create a better GRSC. The effect of uncertainties and carbon constraints on decisions to reduce costs and emissions are also shown. Copyright © 2017 Elsevier Ltd. All rights reserved.

Past and future cadmium emissions from municipal solid-waste incinerators in Japan for the assessment of cadmium control policy.

Science.gov (United States)

Ono, Kyoko

2013-11-15

Cadmium (Cd) is a harmful pollutant emitted from municipal solid-waste incinerators (MSWIs). Cd stack emissions from MSWIs have been estimated between 1970 and 2030 in Japan. The aims of this study are to quantify emitted Cd by category and to analyze Cd control policies to reduce emissions. Emissions were estimated using a dynamic substance flow analysis (SFA) that took into account representative waste treatment flows and historical changes in emission factors. This work revealed that the emissions peaked in 1973 (11.1t) and were ten times those in 2010 (1.2 t). Emission from MSWIs was two-thirds of that from non-ferrous smelting in 2010. The main Cd emission source was pigment use in the 1970s, but after 2000 it had shifted to nickel-cadmium (Ni-Cd) batteries. Future emissions were estimated for 2030. Compared to the business-as-usual scenario, an intensive collection of used Ni-Cd batteries and a ban on any future use of Ni-Cd batteries will reduce emissions by 0.09 and 0.3 1t, respectively, in 2030. This approach enables us to identify the major Cd emission source from MSWIs, and to prioritize the possible Cd control policies. Copyright © 2013 Elsevier B.V. All rights reserved.

Development of analog solid-state photo-detectors for Positron Emission Tomography

International Nuclear Information System (INIS)

Bisogni, Maria Giuseppina; Morrocchi, Matteo

2016-01-01

Solid-state photo-detectors are one of the main innovations of past century in the field of sensors. First produced in the early forties with the invention of the p–n junction in silicon and the study of its optical properties, photo-detectors received a major boost in the sixties when the p-i-n (PIN) photodiode was developed and successfully used in several applications. The development of devices with internal gain, avalanche photodiodes (APD) first and then Geiger-mode avalanche photodiodes, named single photon avalanche diode (SPAD), leads to a substantial improvement in sensitivity and allowed single photon detection. Later on, thousands of SPADs have been assembled in arrays of few millimeters squared (named SiPM, silicon photo-multiplier) with single photon resolution. The high internal gain of SiPMs, together with other features peculiar of the silicon technology like compactness, speed and compatibility with magnetic fields, promoted SiPMs as the principal photo-detector competitor of photomultipliers in many applications from radiation detection to medical imaging. This paper provides a review of the properties of analog solid-state photo-detectors. Particular emphasis is given to latest advances on Positron Emission Tomography instrumentation boosted by the adoption of the silicon photo-detectors as an alternative to photomultiplier tubes (PMTs). Special attention is dedicated to the SiPMs, which are playing a key role in the development of innovative scanners.

Development of analog solid-state photo-detectors for Positron Emission Tomography

Energy Technology Data Exchange (ETDEWEB)

Bisogni, Maria Giuseppina, E-mail: giuseppina.bisogni@pi.infn.it; Morrocchi, Matteo

2016-02-11

Solid-state photo-detectors are one of the main innovations of past century in the field of sensors. First produced in the early forties with the invention of the p–n junction in silicon and the study of its optical properties, photo-detectors received a major boost in the sixties when the p-i-n (PIN) photodiode was developed and successfully used in several applications. The development of devices with internal gain, avalanche photodiodes (APD) first and then Geiger-mode avalanche photodiodes, named single photon avalanche diode (SPAD), leads to a substantial improvement in sensitivity and allowed single photon detection. Later on, thousands of SPADs have been assembled in arrays of few millimeters squared (named SiPM, silicon photo-multiplier) with single photon resolution. The high internal gain of SiPMs, together with other features peculiar of the silicon technology like compactness, speed and compatibility with magnetic fields, promoted SiPMs as the principal photo-detector competitor of photomultipliers in many applications from radiation detection to medical imaging. This paper provides a review of the properties of analog solid-state photo-detectors. Particular emphasis is given to latest advances on Positron Emission Tomography instrumentation boosted by the adoption of the silicon photo-detectors as an alternative to photomultiplier tubes (PMTs). Special attention is dedicated to the SiPMs, which are playing a key role in the development of innovative scanners.

X-ray emission from high-intensity interaction of picosecond and subnanosecond laser pulses with solid targets

Czech Academy of Sciences Publication Activity Database

Badziak, J.; Jabloňski, S.; Makowski, J.; Parys, P.; Ryc, L.; Vankov, A. B.; Wolowski, J.; Woryna, E.; Juha, Libor; Krása, Josef

2002-01-01

Roč. 32, 1-2 (2002), s. 41-46 ISSN 0078-5466 Grant - others:KBN(PL) 2PO3B08219 Institutional research plan: CEZ:AV0Z1010921 Keywords : soft x-ray emission * laser produced plasma * 1-ps and 0.5ns laser pulses Subject RIV: BH - Optics, Masers, Lasers Impact factor: 0.291, year: 2002

Study of x-ray emission enhancement via high contrast femtosecond laser interacting with solid foil

International Nuclear Information System (INIS)

Chen, Liming; Kando, Masaki; Bulanov, S.V.; Koga, James K.; Tajima, Toshiki; Xu M.H.; Yuan X.H.; Li Y.T.; Dong Q.L.; Zhang J.

2007-01-01

We studied the hard x-ray emission and the Kα x-ray conversion efficiency (η K ) produced by 60 fs high contrast frequency doubled Ti: sapphire laser pulse focused on Cu foil target. Cu Kα photon emission obtained with second harmonic laser pulse is more intense than the case of fundamental laser pulse. The Cu η K shows strong dependence on laser nonlinearly skewed pulse shape and reaches the maximum value 4x10 -4 with 100 fs negatively skewed pulse. It shows the electron spectrum shaping contribute to the increase of η K . (author)

New emissions targeting strategy for site utility of process industries

International Nuclear Information System (INIS)

Manesh, Mohamamd Hasan Khoshgoftar; Amidpour, Majid; Hamedi, Mohammad Hosein; Abadi, Sajad Khamis; Ghalami, Hooman

2013-01-01

A new procedure for environmental targeting of co-generation system is presented. The proposed method is based on the concepts of pinch technology for total site targeting of fuel, power, steam, environmental impacts and total annualized cost with considering emissions taxes. This approach provides a consistent, general procedure for determining mass flow rates and efficiencies of the applied turbines. This algorithm utilizes the relationship of entropy with enthalpy and isentropic efficiency. Also, the life cycle assessment (LCA) as a well-known tool for analyzing environmental impacts on a wide perspective with reference to a product system and the related environmental and economic impacts have been applied. In this regard, a damage-oriented impact analysis method based on Eco-indicator 99 and footprints analysis was considered. In addition, the present work demonstrates the effect of including both sensible and latent heating of steam in the extended Site Utility Grand Composite Curve (ESUGCC). It is shown that including sensible heating allows for better thermal matching between the processes. Furthermore, the other representation YSUGCC as the other form of Site Utility Grand Composite has been proposed. Two case studies were used to illustrate the usefulness of the new environmental targeting method

European trends in greenhouse gases emissions from integrated solid waste management.

Science.gov (United States)

Calabrò, Paolo S; Gori, Manuela; Lubello, Claudio

2015-01-01

The European Union (EU) has 28 member states, each with very different characteristics (e.g. surface, population density, per capita gross domestic product, per capita municipal solid waste (MSW) production, MSW composition, MSW management options). In this paper several integrated waste management scenarios representative of the European situation have been generated and analysed in order to evaluate possible trends in the net emission of greenhouse gases and in the required landfill volume. The results demonstrate that an integrated system with a high level of separate collection, efficient energy recovery in waste-to-energy plants and very limited landfill disposal is the most effective according to the indices adopted. Moreover, it is evident that a fully integrated system can make MSW management a carbon sink with a potentiality of up to approximately 40 Mt CO2eq year(-1).

A technique for measurement of vector and tensor polarization in solid spin one polarized targets

International Nuclear Information System (INIS)

Kielhorn, W.F.

1991-06-01

Vector and tensor polarizations are explicitly defined and used to characterize the polarization states of spin one polarized targets, and a technique for extracting these polarizations from nuclear magnetic resonance (NMR) data is developed. This technique is independent of assumptions about spin temperature, but assumes the target's crystal structure induces a quadrupole interaction with the spin one particles. Analysis of the NMR signals involves a computer curve fitting algorithm implemented with a fast Fourier transform method which speeds and simplifies curve fitting algorithms used previously. For accurate curve fitting, the NMR electronic circuit must be modeled by the fitting algorithm. Details of a circuit, its model, and data collected from this circuit are given for a solid deuterated ammonia target. 37 refs., 19 figs., 3 tabs

Laser polarization dependence of proton emission from a thin foil target irradiated by a 70 fs, intense laser pulse

International Nuclear Information System (INIS)

Fukumi, A.; Nishiuchi, M.; Daido, H.; Li, Z.; Sagisaka, A.; Ogura, K.; Orimo, S.; Kado, M.; Hayashi, Y.; Mori, M.; Bulanov, S.V.; Esirkepov, T.; Nemoto, K.; Oishi, Y.; Nayuki, T.; Fujii, T.; Noda, A.; Nakamura, S.

2005-01-01

A study of proton emission from a 3-μm-thick Ta foil target irradiated by p-, s-, and circularly polarized laser pulses with respect to the target plane has been carried out. Protons with energies up to 880 keV were observed in the target normal direction under the irradiation by the p-polarized laser pulse, which yielded the highest efficiency for proton emission. In contrast, s- and circularly polarized laser pulses gave the maximum energies of 610 and 680 keV, respectively. The difference in the maximum energy between the p- and s-polarized cases was associated with the difference between the sheath fields estimated from electron spectra

Evaluation of Efficiency Activities in the Industrial Sector Undertaken in Response to Greenhouse Gas Emission Reduction Targets

Energy Technology Data Exchange (ETDEWEB)

Price, Lynn; de la Rue du Can, Stephane; Lu, Hongyou; Horvath, Arpad

2010-05-21

The 2006 California Global Warming Solutions Act calls for reducing greenhouse gas (GHG) emissions to 1990 levels by 2020. Meeting this target will require action from all sectors of the California economy, including industry. The industrial sector consumes 25% of the energy used and emits 28% of the carbon dioxide (CO{sub 2}) produced in the state. Many countries around the world have national-level GHG reduction or energy-efficiency targets, and comprehensive programs focused on implementation of energy efficiency and GHG emissions mitigation measures in the industrial sector are essential for achieving their goals. A combination of targets and industry-focused supporting programs has led to significant investments in energy efficiency as well as reductions in GHG emissions within the industrial sectors in these countries. This project has identified program and policies that have effectively targeted the industrial sector in other countries to achieve real energy and CO{sub 2} savings. Programs in Ireland, France, The Netherlands, Denmark, and the UK were chosen for detailed review. Based on the international experience documented in this report, it is recommended that companies in California's industrial sector be engaged in a program to provide them with support to meet the requirements of AB32, The Global Warming Solution Act. As shown in this review, structured programs that engage industry, require members to evaluate their potential efficiency measures, plan how to meet efficiency or emissions reduction goals, and provide support in achieving the goals, can be quite effective at assisting companies to achieve energy efficiency levels beyond those that can be expected to be achieved autonomously.

Experimental Set-up for Irradiation of Solid H2 and D2 with Charged Particles of keV Energies

DEFF Research Database (Denmark)

Sørensen, H.

1976-01-01

crystal film thickness monitor. The target plate, which can be heated so that films are removable by evaporation, may be used both as a calorimeter and as a beam current collector. Methods for measurement of secondary electron emission coefficients were developed, and preliminary measurements were made...... with electrons and hydrogen ions. For electron bombardment, the secondary electron emission coefficient of solid deuterium was much smaller than one. It was shown possible to use the set-up to study beam desorption of very thin films. Furthermore the set-up could be used for measuring the energy......An experimental facility was built where films of solid deuterium (and hydrogen) may be made with known thickness and irradiated with pulsed beams of electrons (up to 3 keV) and light ions (up to 10 keV). Films are made on a target plate held at 2.5–3 K. Film growth rate is calibrated with a quartz...

Emission pathways to achieve 2.0°C and 1.5°C climate targets

Science.gov (United States)

Su, Xuanming; Takahashi, Kiyoshi; Fujimori, Shinichiro; Hasegawa, Tomoko; Tanaka, Katsumasa; Kato, Etsushi; Shiogama, Hideo; Masui, Toshihiko; Emori, Seita

2017-06-01

We investigated the feasibilities of 2.0°C and 1.5°C climate targets by considering the abatement potentials of a full suite of greenhouse gases, pollutants, and aerosols. We revised the inter-temporal dynamic optimization model DICE-2013R by introducing three features as follows. First, we applied a new marginal abatement cost curve derived under moderate assumptions regarding future socioeconomic development—the Shared Socioeconomic Pathways 2 (SSP2) scenario. Second, we addressed emission abatement for not only industrial CO2 but also land-use CO2, CH4, N2O, halogenated gases, CO, volatile organic compounds, SOx, NOx, black carbon and organic carbon. Third, we improved the treatment of the non-CO2 components in the climate module based on MAGICC 6.0. We obtained the following findings: (1) It is important to address the individual emissions in an analysis of low stabilization scenarios because abating land-use CO2, non-CO2 and aerosol emissions also contributes to maintaining a low level of radiative forcing and substantially affects the climate costs. (2) The 2.0°C target can be efficiently reached under the assumptions of the SSP2 scenario. (3) The 1.5°C target can be met with early deep cuts under the assumption of a temperature overshoot, and it will triple the carbon price and double the mitigation cost compared with the 2.0°C case.

Relations of secondary electron emission to microdosimetry and applications to two-target theory

International Nuclear Information System (INIS)

Forsberg, B.J.; Burlin, T.E.

1978-01-01

Secondary electron emission has been suggested as a phenomenon that offers considerable potential for microdosimetric studies (Burlin, 1973). This potential is examined further through a theoretical study. Previous work on the stochastic nature of secondary electron emission is reviewed and in particular a Monte Carlo programme of McDonald, Lamki and Delaney (1971, 1973) is developed. Lineal energy distributions are presented for tissue equivalent volumes of about 5nm in three materials for different electron energies. The dose mean of lineal energy and the frequency mean of lineal energy are calculated and these results for volumes with linear dimension of a few nanometers are compared with results of Bengtsson and Lindborg (1974), Braby and Ellett (1971) and Dvorak (1975). Several authors have suggested that some radiobiological effects may result from energy deposition in two different targets. An experimental investigation using proportional counter measurements to simulate two-target theory has been reported. In this paper an alternative technique to twin-proportional counter measurements, based on the secondary electron emission from the two sides of a thin foil is discussed. The extended version of the programme calculates the coincident P(nsub(i),nsub(e)) distribution, that is the number of secondary electrons pair (nsub(i), nsub(e)) is recorded, where nsub(i) is the number of secondary electrons leaving the incident side and nsub(e) is leaving the exit side of the foil simultaneously

Ammonia emissions in Europe

DEFF Research Database (Denmark)

Jacobsen, Brian H.

2012-01-01

The NEC (National Emission Ceiling) directive has set targets for the 2010 ammonia emissions from a number of European countries. The target will be reached by most EU-countries and the total emission for EU-27 has been reduced by 22% from 1990 to 2007. Denmark is one of the countries with the la......The NEC (National Emission Ceiling) directive has set targets for the 2010 ammonia emissions from a number of European countries. The target will be reached by most EU-countries and the total emission for EU-27 has been reduced by 22% from 1990 to 2007. Denmark is one of the countries...

Electron spin resonance and its implication on the maximum nuclear polarization of deuterated solid target materials

International Nuclear Information System (INIS)

Heckmann, J.; Meyer, W.; Radtke, E.; Reicherz, G.; Goertz, S.

2006-01-01

ESR spectroscopy is an important tool in polarized solid target material research, since it allows us to study the paramagnetic centers, which are used for the dynamic nuclear polarization (DNP). The polarization behavior of the different target materials is strongly affected by the properties of these centers, which are added to the diamagnetic materials by chemical doping or irradiation. In particular, the ESR linewidth of the paramagnetic centers is a very important parameter, especially concerning the deuterated target materials. In this paper, the results of the first precise ESR measurements of the deuterated target materials at a DNP-relevant magnetic field of 2.5 T are presented. Moreover, these results allowed us to experimentally study the correlation between ESR linewidth and maximum deuteron polarization, as given by the spin-temperature theory

Basic features of electromagnetic pulse generated in a laser-target chamber at 3-TW laser facility PALS

International Nuclear Information System (INIS)

De Marco, M; Pfeifer, M; Krousky, E; Krasa, J; Cikhardt, J; Klir, D; Nassisi, V

2014-01-01

We describe the radiofrequency emission taking place when 300 ps laser pulses irradiate various solid targets with an intensity of 10 16 W/cm 2 . The emission of intense electromagnetic pulses was observed outside the laser target chamber by two loop antennas up to 1 GHz. Electromagnetic pulses can be 800 MHz transients, which decay from a peak electromagnetic field of E 0 ≊ 7 kV/m and H 0 ≊ 15 A/m. The occurrence of these electromagnetic pulses is associated with generation of hard x-rays with photon energies extending beyond 1 MeV. This contribution reports the first observation of this effect at the PALS facility.

Formation of (Xe2H)* centers in solid Xe via recombination: nonstationary luminescence and 'internal electron emission'

International Nuclear Information System (INIS)

Savchenko, E.V.; Khyzhniy, I.V.; Uyutov, S.A.; Gumenchuk, G.B.; Ponomarev, A.N.; Bondybey, V.E.; Beyer, M.K.

2010-01-01

The formation of excimers (Xe 2 H) * in solid Xe doped with molecular hydrogen under electron beam is studied using the original two-stage technique of nonstationary (NS) cathodoluminescence (CL) in combination with the current activation spectroscopy method - thermally stimulated exoelectron emission (TSEE). Charged species were generated using a high-density electron beam. The species produced were then probed with a low density beam on gradual sample heating. The near UV emission of the (Xe 2 H) * was used to monitor the neutralization process. It is found that the temperature behavior of the NS CL band of (Xe 2 H) * clearly correlates with the yield of TSEE measured after identical pre-irradiation of the sample. The fingerprints of the thermally stimulated detrapping of electrons - 'internal electron emission' in the spectrum of NS CL point to the essential role of neutralization reaction in the stability of the proton solvated by rare-gas atoms.

Curbing dioxin emissions from municipal solid waste incineration in China: re-thinking about management policies and practices.

Science.gov (United States)

Cheng, Hefa; Hu, Yuanan

2010-09-01

As one of the countries with large amounts of dioxin releases, the control of dioxins is a major challenge for China. Municipal solid waste (MSW) incineration should be considered a high priority source of dioxin emissions because it is playing an increasingly more important role in waste management. MSW incineration in China has much higher emission rates of dioxins than in the developed countries, partially resulting from the gaps in the technologies of incineration and flue gas cleaning. Moreover, the current management policies and practices also contribute significantly to the problem. We recommend lowering dioxin emission standard, strengthening fly ash management, and improving regulation enforcement to reduce dioxin releases into the environment from MSW incineration. We also propose that alternative strategies should be considered on dioxin control and call for an expansion of economic instruments in waste management to reduce waste generation and thus the need for incineration. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

Model of two temperatures of the laser evaporation of solid targets

International Nuclear Information System (INIS)

Tolentino E, P.; Gutierrez T, C.; Camps C, E.

2007-01-01

The energy transmission in the evaporation process of a solid target by a laser pulse by means of the model of two temperatures which consists on two equations of heat conduction coupled by means of an electron-phonon coupling factor that means the energy transfer rate between the electrons and the net is described. This electron-phonon coupling factor is calculated for the particular case of the graphite, the obtaining of the analytic solutions in a space dimension of the system of non linear partial differential equations is shown considering two forms of the laser pulse (gaussian and delta function) and the electron temperature distributions of temperature and of the net are analyzed. (Author)

The impact of municipal solid waste management on greenhouse gas emissions in the United States.

Science.gov (United States)

Weitz, Keith A; Thorneloe, Susan A; Nishtala, Subba R; Yarkosky, Sherry; Zannes, Maria

2002-09-01

Technological advancements, environmental regulations, and emphasis on resource conservation and recovery have greatly reduced the environmental impacts of municipal solid waste (MSW) management, including emissions of greenhouse gases (GHGs). This study was conducted using a life-cycle methodology to track changes in GHG emissions during the past 25 years from the management of MSW in the United States. For the baseline year of 1974, MSW management consisted of limited recycling, combustion without energy recovery, and landfilling without gas collection or control. This was compared with data for 1980, 1990, and 1997, accounting for changes in MSW quantity, composition, management practices, and technology. Over time, the United States has moved toward increased recycling, composting, combustion (with energy recovery) and landfilling with gas recovery, control, and utilization. These changes were accounted for with historical data on MSW composition, quantities, management practices, and technological changes. Included in the analysis were the benefits of materials recycling and energy recovery to the extent that these displace virgin raw materials and fossil fuel electricity production, respectively. Carbon sinks associated with MSW management also were addressed. The results indicate that the MSW management actions taken by U.S. communities have significantly reduced potential GHG emissions despite an almost 2-fold increase in waste generation. GHG emissions from MSW management were estimated to be 36 million metric tons carbon equivalents (MMTCE) in 1974 and 8 MMTCE in 1997. If MSW were being managed today as it was in 1974, GHG emissions would be approximately 60 MMTCE.

Ultra-High-Contrast Laser Acceleration of Relativistic Electrons in Solid Targets

Energy Technology Data Exchange (ETDEWEB)

Higginson, Drew Pitney [Univ. of California, San Diego, CA (United States)

2013-01-01

The cone-guided fast ignition approach to Inertial Con nement Fusion requires laser-accelerated relativistic electrons to deposit kilojoules of energy within an imploded fuel core to initiate fusion burn. One obstacle to coupling electron energy into the core is the ablation of material, known as preplasma, by laser energy proceeding nanoseconds prior to the main pulse. This causes the laser-absorption surface to be pushed back hundreds of microns from the initial target surface; thus increasing the distance that electrons must travel to reach the imploded core. Previous experiments have shown an order of magnitude decrease in coupling into surrogate targets when intentionally increasing the amount of preplasma. Additionally, for electrons to deposit energy within the core, they should have kinetic energies on the order of a few MeV, as less energetic electrons will be stopped prior to the core and more energetic electrons will pass through the core without depositing much energy. Thus a quantitative understanding of the electron energy spectrum and how it responds to varied laser parameters is paramount for fast ignition. For the rst time, this dissertation quantitatively investigates the acceleration of electrons using an ultra-high-contrast laser. Ultra-high-contrast lasers reduce the laser energy that reaches the target prior to the main pulse; drastically reducing the amount of preplasma. Experiments were performed in a cone-wire geometry relevant to fast ignition. These experiments irradiated the inner-tip of a Au cone with the laser and observed electrons that passed through a Cu wire attached to the outer-tip of the cone. The total emission of K x-rays is used as a diagnostic to infer the electron energy coupled into the wire. Imaging the x-ray emission allowed an e ective path-length of electrons within the wire to be determined, which constrained the electron energy spectrum. Experiments were carried out on the ultra-high-contrast Trident laser at Los

A technique for measurement of vector and tensor polarization in solid spin one polarized targets

Energy Technology Data Exchange (ETDEWEB)

Kielhorn, W.F.

1991-06-01

Vector and tensor polarizations are explicitly defined and used to characterize the polarization states of spin one polarized targets, and a technique for extracting these polarizations from nuclear magnetic resonance (NMR) data is developed. This technique is independent of assumptions about spin temperature, but assumes the target's crystal structure induces a quadrupole interaction with the spin one particles. Analysis of the NMR signals involves a computer curve fitting algorithm implemented with a fast Fourier transform method which speeds and simplifies curve fitting algorithms used previously. For accurate curve fitting, the NMR electronic circuit must be modeled by the fitting algorithm. Details of a circuit, its model, and data collected from this circuit are given for a solid deuterated ammonia target. 37 refs., 19 figs., 3 tabs.

Auger emission from solid surfaces bombarded with ions

International Nuclear Information System (INIS)

Grizzi, Oscar.

1986-01-01

The Auger electron emission from Be, Na, Mg, Al and Si bombarded with 0,5-20 KeV noble gas ions is studied. Sharp structures of the Auger electron spectra of Na and Be were identified. A Monte Carlo program was adapted to simulate the colision cascade in the solid, inner shell excitations and Auger decays. From the comparision of experimental and simulated Auger intensities, the relative role of symmetric and asymmetric collisions in Be K- and Al L-shell excitation were evaluated. In the case of Be, the discussion of the exciting processes to higher projectile energies was extended. To this end, the simulation to early measurements of Be K X-ray yields was applied. From this analysis, information about the variations of the fluorescence yield and outer-shell occupation numbers of Be with projectile energy was obtained. The study of the shape of the sharp Auger structures and their dependence with the energy and incidence projectile angle gives information about the collisional processes, inner hole lifetimes and Auger decays. From the evaluation of the energy and angular distribution of the excited sputtered atoms and the interaction between them and the metallic-surface, the energy shift distributions in the Auger energies were obtained. From the comparison of these distributions with the experimental atomic peaks, the main causes of the broadening of these peaks were determined. (M.E.L.) [es

Studies on keV and eV electrons in solids

International Nuclear Information System (INIS)

Schou, J.

1979-10-01

The interaction between keV or eV electrons and solids was studied. The results presented mostly concern problems in connection with electron irradiation of solids, but to some extent they also include ion-induced secondary electron emission. The experiments were mainly performed on solidified gases using 1 - 3 keV electrons. The projected range of electrons was determined in solid hydrogen, deuterium and nitrogen. The true secondary electron emission coefficient and the electron reflection coefficient of solid hydrogen, deuterium and nitrogen were measured. The escape depth of the true secondary electrons in nitrogen was determined. The angular dependence of both the reflection coefficient and the true secondary electron emission coefficient of solid hydrogen and deuterium was investigated. Both ion- and electron-induced secondary electron emission were treated theoretically on the basis of ionization cascade theory. (Auth.)

Positron emission tomography in amyotrophic lateral sclerosis: Towards targeting of molecular pathological hallmarks

Energy Technology Data Exchange (ETDEWEB)

Willekens, Stefanie M.A.; Weehaeghe, Donatienne van [University Hospitals Leuven and KU Leuven, Division of Nuclear Medicine, Department of Imaging and Pathology, Leuven (Belgium); Damme, Philip van [University Hospitals Leuven, Department of Neurology, Leuven (Belgium); KU Leuven, Department of Neurosciences, Experimental Neurology, Leuven (Belgium); Leuven Research Institute for Neuroscience and Disease (LIND), Leuven (Belgium); VIB, Vesalius Research Center, Laboratory of Neurobiology, Leuven (Belgium); Laere, Koen van [University Hospitals Leuven and KU Leuven, Division of Nuclear Medicine, Department of Imaging and Pathology, Leuven (Belgium); Leuven Research Institute for Neuroscience and Disease (LIND), Leuven (Belgium)

2017-03-15

During the past decades, extensive efforts have been made to expand the knowledge of amyotrophic lateral sclerosis (ALS). However, clinical translation of this research, in terms of earlier diagnosis and improved therapy, remains challenging. Since more than 30% of motor neurons are lost when symptoms become clinically apparent, techniques allowing non-invasive, in vivo detection of motor neuron degeneration are needed in the early, pre-symptomatic disease stage. Furthermore, it has become apparent that non-motor signs play an important role in the disease and there is an overlap with cognitive disorders, such as frontotemporal dementia (FTD). Radionuclide imaging, such as positron emission tomography (PET) and single-photon emission computed tomography (SPECT), form an attractive approach to quantitatively monitor the ongoing neurodegenerative processes. Although [{sup 18}F]-FDG has been recently proposed as a potential biomarker for ALS, active targeting of the underlying pathologic molecular processes is likely to unravel further valuable disease information and may help to decipher the pathogenesis of ALS. In this review, we provide an overview of radiotracers that have already been applied in ALS and discuss possible novel targets for in vivo imaging of various pathogenic processes underlying ALS onset and progression. (orig.)

Positron emission tomography in amyotrophic lateral sclerosis: Towards targeting of molecular pathological hallmarks

International Nuclear Information System (INIS)

Willekens, Stefanie M.A.; Weehaeghe, Donatienne van; Damme, Philip van; Laere, Koen van

2017-01-01

During the past decades, extensive efforts have been made to expand the knowledge of amyotrophic lateral sclerosis (ALS). However, clinical translation of this research, in terms of earlier diagnosis and improved therapy, remains challenging. Since more than 30% of motor neurons are lost when symptoms become clinically apparent, techniques allowing non-invasive, in vivo detection of motor neuron degeneration are needed in the early, pre-symptomatic disease stage. Furthermore, it has become apparent that non-motor signs play an important role in the disease and there is an overlap with cognitive disorders, such as frontotemporal dementia (FTD). Radionuclide imaging, such as positron emission tomography (PET) and single-photon emission computed tomography (SPECT), form an attractive approach to quantitatively monitor the ongoing neurodegenerative processes. Although ["1"8F]-FDG has been recently proposed as a potential biomarker for ALS, active targeting of the underlying pathologic molecular processes is likely to unravel further valuable disease information and may help to decipher the pathogenesis of ALS. In this review, we provide an overview of radiotracers that have already been applied in ALS and discuss possible novel targets for in vivo imaging of various pathogenic processes underlying ALS onset and progression. (orig.)

Time resolved optical emission spectroscopy of cross-beam pulsed laser ablation on graphite targets

International Nuclear Information System (INIS)

Sangines, R.; Sanchez Ake, C.; Sobral, H.; Villagran-Muniz, M.

2007-01-01

Cross-beam pulsed laser ablation with two delayed lasers is performed on two perpendicular graphite targets. The time delay between lasers is varied by up to 5 μs, and physical changes on the second plasma, due to the interaction with the first generated one, are determined by time resolved optical emission spectroscopy

Greenhouse gas emissions from dairy manure management: a review of field-based studies.

Science.gov (United States)

Owen, Justine J; Silver, Whendee L

2015-02-01

Livestock manure management accounts for almost 10% of greenhouse gas emissions from agriculture globally, and contributes an equal proportion to the US methane emission inventory. Current emissions inventories use emissions factors determined from small-scale laboratory experiments that have not been compared to field-scale measurements. We compiled published data on field-scale measurements of greenhouse gas emissions from working and research dairies and compared these to rates predicted by the IPCC Tier 2 modeling approach. Anaerobic lagoons were the largest source of methane (368 ± 193 kg CH4 hd(-1) yr(-1)), more than three times that from enteric fermentation (~120 kg CH4 hd(-1) yr(-1)). Corrals and solid manure piles were large sources of nitrous oxide (1.5 ± 0.8 and 1.1 ± 0.7 kg N2O hd(-1) yr(-1), respectively). Nitrous oxide emissions from anaerobic lagoons (0.9 ± 0.5 kg N2O hd(-1) yr(-1)) and barns (10 ± 6 kg N2O hd(-1) yr(-1)) were unexpectedly large. Modeled methane emissions underestimated field measurement means for most manure management practices. Modeled nitrous oxide emissions underestimated field measurement means for anaerobic lagoons and manure piles, but overestimated emissions from slurry storage. Revised emissions factors nearly doubled slurry CH4 emissions for Europe and increased N2O emissions from solid piles and lagoons in the United States by an order of magnitude. Our results suggest that current greenhouse gas emission factors generally underestimate emissions from dairy manure and highlight liquid manure systems as promising target areas for greenhouse gas mitigation. © 2014 John Wiley & Sons Ltd.

Absolute Soft X-ray Emission Measurements at the Nike Laser

Science.gov (United States)

Weaver, J.; Atkin, R.; Boyer, C.; Colombant, D.; Feldman, U.; Fielding, D.; Gardner, J.; Holland, G.; Klapisch, M.; Mostovych, A. N.; Obenscain, S.; Seely, J. F.

2002-11-01

Recent experiments at the Nike laser facility have demonstrated that, when a low intensity prepulse ( 2main laser intensity) is used to heat a thin Au or Pd coating on a planar CH target, the growth of non-uniformities due to laser imprint can be reduced from the growth observed for an uncoated CH target. The absolute radiation intensity in the soft x-ray region (0.1-1 keV) has a important role in the energy balance for layered targets. There is an ongoing effort to characterize the soft x-ray emission using an absolutely calibrated transmission grating spectrometer and filtered diode modules. Measurements of the angular distribution of the emission from unlayered solid targets (Au, Pd, CH) have recently been made using an array of moveable filtered diode modules. The data from the angular distribution studies will be presented. A new absolutely calibrated, time-resolving transmission grating spectrometer has been installed at the Nike. The new version has improved spectral resolution, selectable transmission filters, and the potential for simultaneous temporal, spatial, and spectral resolution. Preliminary data from the new spectrometer will be presented and future experiments will be briefly discussed. *Work was supported by DoE

Solid residues; Os residuos solidos

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-07-01

This chapter gives a general overview on the general effects of the solid waste pollution, the principal pollutants emitted by the oil refineries, control actions for the solid waste emissions, the minimization actions, and the effluent treatment.

High energy density matter issues related to future circular collider. Simulations of full beam impact with a solid copper cylindrical target

Energy Technology Data Exchange (ETDEWEB)

Tahir, N.A. [GSI Helmholtzzentrum fuer Schwerionenforschung, Darmstadt (Germany); Burkart, F.; Schmidt, R.; Wollmann, D. [CERN-AB, Geneva (Switzerland); Shutov, A. [Institute of Problems of Chemical Physics, Chernogolovka (Russian Federation); Piriz, A.R. [E.T.S.I. Industrials, University of Castilla-La Mancha, Ciudad Real (Spain)

2017-11-15

This paper presents numerical simulations of the thermodynamic and hydrodynamic response of a solid copper cylindrical target that is subjected to the full impact of one future circular collider (FCC) ultra-relativistic proton beam. The target is facially irradiated so that the beam axis coincides with the cylinder axis. The simulations have been carried out employing an energy deposition code, FLUKA, and a 2D hydrodynamic code, BIG2, iteratively. The simulations show that, although the static range of a single FCC proton and its shower in solid copper is ∝1.5 m, the full beam may penetrate up to 350 m into the target as a result of hydrodynamic tunnelling. Moreover, simulations also show that a major part of the target is converted into high energy density (HED) matter, including warm dense matter (WDM) and strongly coupled plasma. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Experimental measurements of deep directional columnar heating by laser-generated relativistic electrons at near-solid density

International Nuclear Information System (INIS)

Koch, J.A.; Key, M.H.; Hatchett, S.P.; Lee, R.W.; Pennington, D.; Tabak, M.; Freeman, R.R.; Stephens, R.B.

2002-01-01

In our experiments, we irradiated solid CH targets with a 400 J, 5 ps, 3x10 19 W/cm 2 laser, and we used x-ray imaging and spectroscopic diagnostics to monitor the keV x-ray emission from thin Al or Au tracer layers buried within the targets. The experiments were designed to quantify the spatial distribution of the thermal electron temperature and density as a function of buried layer depth; these data provide insights into the behavior of relativistic electron currents which flow within the solid target and are directly and indirectly responsible for the heating. We measured ∼200-350 eV temperatures and near-solid densities at depths ranging from 5 to 100 μm beneath the target surface. Time-resolved x-ray spectra from Al tracers indicate that the tracers emit thermal x rays and cool slowly compared to the time scale of the laser pulse. Most intriguingly, we consistently observe annular x-ray images in all buried tracer-layer experiments, and these data show that the temperature distribution is columnar, with enhanced heating along the edges of the column. The ring diameters are much greater than the laser focal spot diameter and do not vary significantly with the depth of the tracer layer for depths greater than 30 μm. The local temperatures are 200-350 eV for all tracer depths. We discuss recent simulations of the evolution of electron currents deep within solid targets irradiated by ultra-high-intensity lasers, and we discuss how modeling and analytical results suggest that the annular patterns we observe may be related to locally strong growth of the Weibel instability. We also suggest avenues for future research in order to further illuminate the complex physics of relativistic electron transport and energy deposition inside ultra-high-intensity laser-irradiated solid targets

Evaluating Cytotoxicity of Hyaluronate Targeted Solid Lipid Nanoparticles of Etoposide on SK-OV-3 Cells

Directory of Open Access Journals (Sweden)

Parviz Mohammadi Ghalaei

2014-01-01

Full Text Available The epithelial ovarian carcinoma is one of the most fatal gynecological cancers. Etoposide is used in treating platinum-resistant ovarian cancer. Sodium hyaluronate is a substance that binds to the CD44 receptors overexpressed in SK-OV-3 cells of epithelial ovarian carcinoma. The aim of the present work was to study the cytotoxicity effect of hyaluronate targeted solid lipid nanoparticles (SLNs of etoposide on SK-OV-3 cells. The cytotoxicity of the targeted and nontargeted SLNs of etoposide was compared to free drug on the SK-OV-3 cells by MTT assay method. The cellular uptake of the targeted and nontargeted nanoparticles containing sodium fluorescein was also studied. The difference of cell vitality between nontargeted nanoparticles and also targeted nanoparticles with free drug was significant. Targeted nanoparticles also caused more toxicity than nontargeted nanoparticles (P<0.05. After 4 hours of incubating, the fluorescence was remarkably higher in the cells treated by targeted SLNs rather than nontargeted ones, and there was no observable fluorescence in cells incubated with pure sodium fluorescein. Hyaluronate targeted SLNs containing etoposide increased the cytotoxicity of etoposide on SK-OV-3 cells which may be a worthwhile potential method for reducing the prescribed dose and systemic side effects of this drug in epithelial ovarian carcinoma.

New infrared solid state laser materials for CALIOPE

International Nuclear Information System (INIS)

DeLoach, L.D.; Page, R.H.; Wilke, G.D.

1994-01-01

Tunable infrared laser light may serve as a useful means by which to detect the presence of the targeted effluents. Since optical parametric oscillators (OPOs) have proven to be a versatile method of generating coherent light from the ultraviolet to the mid-infrared, this technology is a promising choice by which to service the CALIOPE applications. In addition, since some uncertainty remains regarding the precise wavelengths and molecules that will be targeted, the deployment of OPOs retains the greatest amount of wavelength flexibility. Another approach that the authors are considering is that of generating tunable infrared radiation directly with a diode-pumped solid state laser (DPSSL). One important advantage of a DPSSL is that it offers flexible pulse format modes that can be tailored to meet the needs of a particular application and target molecule. On the other hand, direct generation by a tunable DPSSL will generally be able to cover a more limited wavelength range than is possible with OPO technology. In support of the CALIOPE objectives the authors are exploring the potential for laser action among a class of materials comprised of transition metal-doped zinc chalcogenide crystals (i.e., ZnS, ZnSe and ZnTe). The Cr 2+ , Co 2+ and Ni 2+ dopants were selected as the most favorable candidates, on the basis of their documented spectral properties in the scientific literature. Thus far, the authors have characterized the absorption and emission properties of these ions in the ZnS and ZnSe crystals. The absorption spectra are used to determine the preferred wavelength at which the crystal should be pumped, while the emission spectra reveal the extent of the tuning range potentially offered by the material. In addition, measurements of the emission lifetime as a function of temperature turn out to be quite useful, since this data is suggestive of the room temperature emission yield

Fairness and cost-effectiveness of CO2 emission reduction targets in the European Union member states. An analysis based on scenario studies

International Nuclear Information System (INIS)

Kram, T.; Ybema, J.R.; Vos, D.

1997-06-01

The Member States of the European Union (EU) have agreed upon a common position in the international negotiations on the limitation of greenhouse gas emissions. The total commitment of the EU is the result of differentiated emission targets for the individual Member States. In this study the results of 4 recent scenario studies on CO2 emission reduction are used to assess the fairness and the cost-effectiveness of the differentiated targets. Here, fairness is measured by the average cost per capita in a country to reach the emission target. Cost-effectiveness is based on the marginal cost of emission reduction. It is noted that there are limitations in the comparability of the country results. Further, the coverage of the EU Member States is not complete in all 4 studies. Robust conclusions could thus not be drawn for all countries. Nonetheless, there are strong indications that the efforts to achieve the emission reduction targets are not evenly distributed. Based on the results the countries can be divided into four groups with different burdens to achieve reduction of CO2 emissions: (a) countries that will probably be faced with above average burdens: Sweden, Italy and the Netherlands; (b) countries that will presumably be faced with above average burdens but for which limited information is available: Austria and Denmark; (c) countries that will probably be faced with average burdens or for which the relative efforts are indistinct: Germany, Portugal, Belgium, Finland and Luxembourg; and (d) countries that will probably be faced with below average burdens: United Kingdom, France, Spain, Ireland and Greece. 1 fig., 12 tabs., 6 refs

Linear acoustic waves induced in a cylindrical solid target by particle beam in e--e+ colliders

International Nuclear Information System (INIS)

Adeyemi, Olufemi Segun

2015-06-01

A future high energy lepton collider will demand high luminosities to achieve its physics goals. For the electron-positron linear collider, the generation of the desired amount of positrons is a non-trivial problem: the positron production target has to survive huge amounts of energy deposited by the bombardment of intense beams of electrons or photons. This causes a rapid increase of the temperature in the target within a very short time period. The resulting deformation due to the induced pressure waves can substantially shorten the operating life-span of the target material. In this work, we study linear effects of induced stress in a solid target through pressure acoustic waves using continuum mechanics. We derived analytical solutions for different cases and imposed different boundary conditions. The application of the model to the SLC positron target gave us the results which are in agreement with the existing literature. In a similar manner, we investigated the effect of single and multiple photon bunches on the conversion target for ILC.

Optical emission from low-energy ion-surface collisions

International Nuclear Information System (INIS)

White, C.W.; Thomas, E.W.; Van der Weg, W.F.; Tolk, N.H.

1977-01-01

Impact of energetic heavy particles on surfaces gives rise to emission of optical radiation from reflected particles, sputtered particles and also from excited states of the solid. The present status of research in this area is reviewed with emphasis on understanding the basic mechanisms which give rise to formation of excited states. The spectral line shape from ejected atoms may be analyzed to provide information on the distribution of speeds and directions of the excited species; the line intensity provides a measure of the probability for creating the state. Formation of excited species is related both to the collision processes within the solid and also to the interaction of the recoiling ejected species with the target surface. Most ejected species are atomic but important examples of ejected molecules are also discussed. Luminescence induced in the solid itself is related to recombination of electron hole pairs and is related significantly to the presence of defects

Intense Non-Linear Soft X-Ray Emission from a Hydride Target during Pulsed D Bombardment

Science.gov (United States)

Miley, George H.; Yang, Yang; Lipson, Andrei; Haque, Munima; Percel, Ian; Romer, Michael

Radiation emission from low-energy nuclear radiation (LENR) electrodes (both charged-particle and X-rays) represents an important feature of LENR in general. Here, calibration, measurement techniques, and soft X-ray emission results from deuterium bombardment of a Pd target (cathode) placed in a pulsed deuterium glow discharge (PGD) are described. An X-ray intensity of 13.4 mW/cm2 and a dose of 3.3 μJ/cm2 were calculated over a 0.5 ms pulse time from AXUV photodiode radiation detector measurements. A most striking feature is that X-ray energies >600 V are observed with a discharge voltage only about half of that value. To further investigate this phenomenon, emission during room temperature D-desorption from electrolytically loaded Pd:Dx cathodes was also studied. The X-ray emission energy observed was quite similar to the PGD case. However, the intensity in this case was almost 13 orders of magnitude lower due to the much lower deuterium fluxes involved.

Intense non-linear soft X-ray emission from a hydride target during pulsed D bombardment

International Nuclear Information System (INIS)

Miley, George H.; Yang, Yang; Lipson, Andrei; Haque, Munima; Percel, Ian; Romer, Michael

2006-01-01

Radiation emission from low-energy nuclear radiation (LENR) electrodes (both charged-particle and X-rays) represents an important feature of LENR in general. Here, calibration, measurement techniques, and soft X-ray emission results from deuterium bombardment of a Pd target (cathode) placed in a pulsed deuterium glow discharge (PGD) are described. An X-ray intensity of 13.4 mW/cm 2 and a dose of 3.3 μJ/cm 2 were calculated over a 0.5 ms pulse time from AXUV photodiode radiation detector measurements. A most striking feature is that X-ray energies >600 V are observed with a discharge voltage only about half of that value. To further investigate this phenomenon, emission during room temperature D-desorption from electrolytically loaded Pd:Dx cathodes was also studied. The X-ray emission energy observed was quite similar to the PGD case. However, the intensity in this case was almost 13 orders of magnitude lower due to the much lower deuterium fluxes involved. (author)

The new solid target system at UNAM in a self-shielded 11 MeV cyclotron

International Nuclear Information System (INIS)

Zarate-Morales, A.; Gaspar-Carcamo, R. E.; Lopez-Rodriguez, V.; Flores-Moreno, A.; Trejo-Ballado, F.; Avila-Rodriguez, Miguel A.

2012-01-01

A dual beam line (BL) self-shielded RDS 111 cyclotron for radionuclide production was installed at the School of Medicine of the National Autonomous University of Mexico in 2001. One of the BL’s was upgraded to Eclipse HP (Siemens) in 2008 and the second BL was recently upgraded (June 2011) to the same version with the option for the irradiation of solid targets for the production of metallic radioisotopes.

Buparvaquone loaded solid lipid nanoparticles for targeted delivery in theleriosis

Directory of Open Access Journals (Sweden)

Maheshkumar P Soni

2014-01-01

Full Text Available Background: Buparvaquone (BPQ, a hydroxynaphthoquinone derivative, has been investigated for the treatment of many infections and is recommended as the gold standard for the treatment of theileriosis. Theileriosis, an intramacrophage infection is localized mainly in reticuloendotheileial system (RES organs. The present study investigates development of solid lipid nanoparticles (SLN of BPQ for targeted delivery to the RES. Materials and Methods: BPQ SLN was prepared using melt method by adding a molten mixture into aqueous Lutrol F68 solution (80°C. Larger batches were prepared up to 6 g of BPQ with GMS: BPQ, 2:1. SLN of designed size were obtained using ultraturrax and high pressure homogenizer. A freeze and thaw study was used to optimize type and concentration of cryoprotectant with Sf: Mean particle size, Si: Initial particle size <1.3. Differential scanning calorimetry (DSC, powder X-ray diffraction (XRD and scanning electron microscope (SEM study was performed on optimized formulation. Formulation was investigated for in vitro serum stability, hemolysis and cell uptake study. Pharmacokinetic and biodistribution study was performed in Holtzman rat. Results: Based on solubility in lipid; glyceryl monostearate (GMS was selected for preparation of BPQ SLN. Batches of BPQ SLN were optimized for average particle size and entrapment efficiency at <100 mg solid content. A combination of Solutol HS-15 and Lutrol F68 at 2% w/v and greater enabled the desired Sf/Si < 1.3. Differential scanning calorimetry and powder X-ray diffraction revealed decrease in crystallinity of BPQ in BPQ SLN while, scanning electron microscope revealed spherical morphology. BPQ SLN revealed good stability at 4°C and 25°C. Low hemolytic potential (<8% and in vitro serum stability up to 5 h was observed. Cytotoxicity of SLN to the U937 cell was low. The macrophage cell line revealed high (52% uptake of BPQ SLN in 1 h suggesting the potential to RES uptake. SLN revealed

Monte Carlo simulation on hard X-ray dose produced in interaction between high intensity laser and solid target

International Nuclear Information System (INIS)

Yang Bo; Qiu Rui; Li Junli; Zhang Hui

2014-01-01

The X-ray dose produced in the interaction between high intensity laser and solid target was studied by simulation using Monte Carlo code. Compared with experimental results, the calculation model was verified. The calculation model was used to study the effect on X-ray dose with different electron temperatures, target materials (including Au, Cu and PE) and thicknesses. The results indicate that the X-ray dose is mainly determined by the electron temperature, and will be affected by the target parameters. X-ray dose of Au is about 1.2 times that of Cu, and is about 5 times that of PE (polyethylene). In addition, compared with other target thickness, when target thickness is the mean range of electron in the target, X-ray dose is relatively large. These results will provide references on evaluating the ionizing radiation dose for laser devices. (authors)

Scenario analysis of energy saving and CO_2 emissions reduction potentials to ratchet up Japanese mitigation target in 2030 in the residential sector

International Nuclear Information System (INIS)

Wakiyama, Takako; Kuramochi, Takeshi

2017-01-01

This paper assesses to what extent CO_2 emissions from electricity in the residential sector can be further reduced in Japan beyond its post-2020 mitigation target (known as “Intended Nationally Determined Contribution (INDC)”). The paper examines the reduction potential of electricity demand and CO_2 emissions in the residential sector by conducting a scenario analysis. Electricity consumption scenarios are set up using a time-series regression model, and used to forecast the electricity consumption patterns to 2030. The scenario analysis also includes scenarios that reduce electricity consumption through enhanced energy efficiency and energy saving measures. The obtained results show that Japan can reduce electricity consumption and CO_2 emissions in the residential sector in 2030 more than the Japanese post-2020 mitigation target indicates. At the maximum, the electricity consumption could be reduced by 35 TWh, which contributes to 55.4 MtCO_2 of emissions reduction in 2030 compared to 2013 if the voluntarily targeted CO_2 intensity of electricity is achieved. The result implies that Japan has the potential to ratchet up post-2020 mitigation targets discussed under the Paris Agreement of the United Nations Framework Convention on Climate Change (UNFCCC). - Highlights: • Further reduction of electricity consumption is possible beyond Japan's post-2020 mitigation target. • Energy saving efforts by households and incentives to reduce electricity demands are required. • Improvement of CO_2 intensity from electricity is a key factor in the reduction of CO_2 emissions.

Targeted next-generation sequencing at copy-number breakpoints for personalized analysis of rearranged ends in solid tumors.

Directory of Open Access Journals (Sweden)

Hyun-Kyoung Kim

Full Text Available BACKGROUND: The concept of the utilization of rearranged ends for development of personalized biomarkers has attracted much attention owing to its clinical applicability. Although targeted next-generation sequencing (NGS for recurrent rearrangements has been successful in hematologic malignancies, its application to solid tumors is problematic due to the paucity of recurrent translocations. However, copy-number breakpoints (CNBs, which are abundant in solid tumors, can be utilized for identification of rearranged ends. METHOD: As a proof of concept, we performed targeted next-generation sequencing at copy-number breakpoints (TNGS-CNB in nine colon cancer cases including seven primary cancers and two cell lines, COLO205 and SW620. For deduction of CNBs, we developed a novel competitive single-nucleotide polymorphism (cSNP microarray method entailing CNB-region refinement by competitor DNA. RESULT: Using TNGS-CNB, 19 specific rearrangements out of 91 CNBs (20.9% were identified, and two polymerase chain reaction (PCR-amplifiable rearrangements were obtained in six cases (66.7%. And significantly, TNGS-CNB, with its high positive identification rate (82.6% of PCR-amplifiable rearrangements at candidate sites (19/23, just from filtering of aligned sequences, requires little effort for validation. CONCLUSION: Our results indicate that TNGS-CNB, with its utility for identification of rearrangements in solid tumors, can be successfully applied in the clinical laboratory for cancer-relapse and therapy-response monitoring.

Targeted next-generation sequencing at copy-number breakpoints for personalized analysis of rearranged ends in solid tumors.

Science.gov (United States)

Kim, Hyun-Kyoung; Park, Won Cheol; Lee, Kwang Man; Hwang, Hai-Li; Park, Seong-Yeol; Sorn, Sungbin; Chandra, Vishal; Kim, Kwang Gi; Yoon, Woong-Bae; Bae, Joon Seol; Shin, Hyoung Doo; Shin, Jong-Yeon; Seoh, Ju-Young; Kim, Jong-Il; Hong, Kyeong-Man

2014-01-01

The concept of the utilization of rearranged ends for development of personalized biomarkers has attracted much attention owing to its clinical applicability. Although targeted next-generation sequencing (NGS) for recurrent rearrangements has been successful in hematologic malignancies, its application to solid tumors is problematic due to the paucity of recurrent translocations. However, copy-number breakpoints (CNBs), which are abundant in solid tumors, can be utilized for identification of rearranged ends. As a proof of concept, we performed targeted next-generation sequencing at copy-number breakpoints (TNGS-CNB) in nine colon cancer cases including seven primary cancers and two cell lines, COLO205 and SW620. For deduction of CNBs, we developed a novel competitive single-nucleotide polymorphism (cSNP) microarray method entailing CNB-region refinement by competitor DNA. Using TNGS-CNB, 19 specific rearrangements out of 91 CNBs (20.9%) were identified, and two polymerase chain reaction (PCR)-amplifiable rearrangements were obtained in six cases (66.7%). And significantly, TNGS-CNB, with its high positive identification rate (82.6%) of PCR-amplifiable rearrangements at candidate sites (19/23), just from filtering of aligned sequences, requires little effort for validation. Our results indicate that TNGS-CNB, with its utility for identification of rearrangements in solid tumors, can be successfully applied in the clinical laboratory for cancer-relapse and therapy-response monitoring.

Evaluation of solid particle number and black carbon for very low particulate matter emissions standards in light-duty vehicles.

Science.gov (United States)

Chang, M-C Oliver; Shields, J Erin

2017-06-01

To reliably measure at the low particulate matter (PM) levels needed to meet California's Low Emission Vehicle (LEV III) 3- and 1-mg/mile particulate matter (PM) standards, various approaches other than gravimetric measurement have been suggested for testing purposes. In this work, a feasibility study of solid particle number (SPN, d50 = 23 nm) and black carbon (BC) as alternatives to gravimetric PM mass was conducted, based on the relationship of these two metrics to gravimetric PM mass, as well as the variability of each of these metrics. More than 150 Federal Test Procedure (FTP-75) or Supplemental Federal Test Procedure (US06) tests were conducted on 46 light-duty vehicles, including port-fuel-injected and direct-injected gasoline vehicles, as well as several light-duty diesel vehicles equipped with diesel particle filters (LDD/DPF). For FTP tests, emission variability of gravimetric PM mass was found to be slightly less than that of either SPN or BC, whereas the opposite was observed for US06 tests. Emission variability of PM mass for LDD/DPF was higher than that of both SPN and BC, primarily because of higher PM mass measurement uncertainties (background and precision) near or below 0.1 mg/mile. While strong correlations were observed from both SPN and BC to PM mass, the slopes are dependent on engine technologies and driving cycles, and the proportionality between the metrics can vary over the course of the test. Replacement of the LEV III PM mass emission standard with one other measurement metric may imperil the effectiveness of emission reduction, as a correlation-based relationship may evolve over future technologies for meeting stringent greenhouse standards. Solid particle number and black carbon were suggested in place of PM mass for the California LEV III 1-mg/mile FTP standard. Their equivalence, proportionality, and emission variability in comparison to PM mass, based on a large light-duty vehicle fleet examined, are dependent on engine

Field-emission from quantum-dot-in-perovskite solids.

Science.gov (United States)

García de Arquer, F Pelayo; Gong, Xiwen; Sabatini, Randy P; Liu, Min; Kim, Gi-Hwan; Sutherland, Brandon R; Voznyy, Oleksandr; Xu, Jixian; Pang, Yuangjie; Hoogland, Sjoerd; Sinton, David; Sargent, Edward

2017-03-24

Quantum dot and well architectures are attractive for infrared optoelectronics, and have led to the realization of compelling light sensors. However, they require well-defined passivated interfaces and rapid charge transport, and this has restricted their efficient implementation to costly vacuum-epitaxially grown semiconductors. Here we report solution-processed, sensitive infrared field-emission photodetectors. Using quantum-dots-in-perovskite, we demonstrate the extraction of photocarriers via field emission, followed by the recirculation of photogenerated carriers. We use in operando ultrafast transient spectroscopy to sense bias-dependent photoemission and recapture in field-emission devices. The resultant photodiodes exploit the superior electronic transport properties of organometal halide perovskites, the quantum-size-tuned absorption of the colloidal quantum dots and their matched interface. These field-emission quantum-dot-in-perovskite photodiodes extend the perovskite response into the short-wavelength infrared and achieve measured specific detectivities that exceed 10 12 Jones. The results pave the way towards novel functional photonic devices with applications in photovoltaics and light emission.

Methane - quick fix or tough target? New methods to reduce emissions.

Science.gov (United States)

Nisbet, E. G.; Lowry, D.; Fisher, R. E.; Brownlow, R.

2016-12-01

Methane is a cost-effective target for greenhouse gas reduction efforts. The UK's MOYA project is designed to improve understanding of the global methane budget and to point to new methods to reduce future emissions. Since 2007, methane has been increasing rapidly: in 2014 and 2015 growth was at rates last seen in the 1980s. Unlike 20thcentury growth, primarily driven by fossil fuel emissions in northern industrial nations, isotopic evidence implies present growth is driven by tropical biogenic sources such as wetlands and agriculture. Discovering why methane is rising is important. Schaefer et al. (Science, 2016) pointed out the potential clash between methane reduction efforts and food needs of a rising, better-fed (physically larger) human population. Our own work suggests tropical wetlands are major drivers of growth, responding to weather changes since 2007, but there is no acceptable way to reduce wetland emission. Just as sea ice decline indicates Arctic warming, methane may be the most obvious tracker of climate change in the wet tropics. Technical advances in instrumentation can do much in helping cut urban and industrial methane emissions. Mobile systems can be mounted on vehicles, while drone sampling can provide a 3D view to locate sources. Urban land planning often means large but different point sources are typically clustered (e.g. landfill or sewage plant near incinerator; gas wells next to cattle). High-precision grab-sample isotopic characterisation, using Keeling plots, can separate source signals, to identify specific emitters, even where they are closely juxtaposed. Our mobile campaigns in the UK, Kuwait, Hong Kong and E. Australia show the importance of major single sources, such as abandoned old wells, pipe leaks, or unregulated landfills. If such point sources can be individually identified, even when clustered, they will allow effective reduction efforts to occur: these can be profitable and/or improve industrial safety, for example in the

Beyond emission targets: how to strengthen the ambition of NDCs? Results of the MILES project informing the 2018 Facilitative Dialogue

International Nuclear Information System (INIS)

2017-09-01

The Paris Agreement creates a process based on cycles to promote the revision by Parties of their Nationally Determined Contributions (NDCs). This process is primarily aimed at supporting an increase of national emission reduction targets in successive NDC submissions to progressively align them with the goal to limit global average temperature increase to 'well below 2 deg. C'. The UNFCCC 2018 Facilitative Dialogue (FD) is the first milestone of this process, in which Parties will collectively take stock of climate action and identify options to update their NDCs by 2020. This report contributes to the preparation of the 2018 FD by presenting insights from the Modelling and Informing Low Emission Strategies (MILES) project (see box 1, page 4). This research builds on analyses of climate action from a simultaneously national and global perspective, articulating the 2030 time frame of the NDCs with mid-century strategies, and capturing the link between low-emission pathways and national socio-economic circumstances, policy priorities and development objectives. The country-specific analyses supporting these insights do not aim at assessing the ambition of individual countries' commitments. Rather, they illustrate potentially common issues across different countries in how they define and implement their own commitments and, therefore, what useful and universally applicable messages can be derived from these analyses as a whole. Key messages: - A credible transition towards the Paris long-term goal requires deeper emission reductions before 2030. - Countries should identify the sectoral transformations required to implement the emission targets. - A smooth transition towards 2 deg. C requires an acceleration of investment shifts in the energy sector before 2030. - The diffusion of key emerging low-carbon technologies should strongly accelerate. This requires an early scale-up of international collaboration on innovation and targeted policy incentives

Apparatus and method for transient thermal infrared emission spectrometry

Science.gov (United States)

McClelland, John F.; Jones, Roger W.

1991-12-24

A method and apparatus for enabling analysis of a solid material (16, 42) by applying energy from an energy source (20, 70) top a surface region of the solid material sufficient to cause transient heating in a thin surface layer portion of the solid material (16, 42) so as to enable transient thermal emission of infrared radiation from the thin surface layer portion, and by detecting with a spectrometer/detector (28, 58) substantially only the transient thermal emission of infrared radiation from the thin surface layer portion of the solid material. The detected transient thermal emission of infrared radiation is sufficiently free of self-absorption by the solid material of emitted infrared radiation, so as to be indicative of characteristics relating to molecular composition of the solid material.

Emissions from residential combustion of different solid fuels. Roekgasemissioner vid anvaendning av olika fasta braenslen i smaaskaliga system

Energy Technology Data Exchange (ETDEWEB)

Rudling, L

1983-01-01

The emission from different types of solid fuels during combustion in residential furnaces and stoves has been investigated. The following fules were investigated: wood pellets, peat-bark pellets, wood chips, wood logs,wood-briquets, peat briquets, lignite briquets, fuel oil. Three different 20-25 kW boilers were used and one stove and one fire place. The flue gases were analysed for carbon dioxide, carbon monoxide, nitrogen oxides, hydrocarbons, particulates, tar and fluoranthen.

Dynamic energy spectrum and energy deposition in solid target by intense pulsed ion beams

Institute of Scientific and Technical Information of China (English)

Xiao Yu; Xiao-Yun Le; Zheng Liu; Jie Shen; Yu I.Isakova; Hao-Wen Zhong; Jie Zhang; Sha Yan; Gao-Long Zhang; Xiao-Fu Zhang

2017-01-01

A method for analyzing the dynamic energy spectrum of intense pulsed ion beam (IPIB) was proposed.Its influence on beam energy deposition in metal target was studied with IPIB produced by two types of magnetically insulated diodes (MID).The emission of IPIB was described with space charge limitation model,and the dynamic energy spectrum was further analyzed with time-of-flight method.IPIBs generated by pulsed accelerators of BIPPAB-450 (active MID) and TEMP-4M (passive MID) were studied.The dynamic energy spectrum was used to deduce the power density distribution of IPIB in the target with Monte Carlo simulation and infrared imaging diagnostics.The effect on the distribution and evolution of thermal field induced by the characteristics of IPIB dynamic energy spectrum was discussed.

Effects of the ion-solid interaction in glow discharge vapour deposition polymerization of pyromellitic dianhydride

International Nuclear Information System (INIS)

Maggioni, G.; Carturan, S.; Rigato, V.; Pieri, U.

2000-01-01

Low energy He ion bombardment of pyromellitic dianhydride monomer used in glow discharge vapour deposition polymerization (GDVDP) of polyimide coatings and its effects on the film deposition process have been studied. The sublimation of the monomer molecules and the simultaneous formation of a damaged, carbon-rich surface layer on the target are discussed from a theoretical point of view based on simulations of the ion-solid interaction. Optical emission and mass spectrometry have been used to analyse the species emitted from the target. In order to study the time evolution of the PMDA target damage, the deposition rate of monomer molecules has been monitored. FT-IR spectroscopy has been used to determine the molecular damaging of the target monomer and deposited films

Ultra-High-Contrast Laser Acceleration of Relativistic Electrons in Solid Targets

Science.gov (United States)

Higginson, Drew Pitney

The cone-guided fast ignition approach to Inertial Confinement Fusion requires laser-accelerated relativistic electrons to deposit kilojoules of energy within an imploded fuel core to initiate fusion burn. One obstacle to coupling electron energy into the core is the ablation of material, known as preplasma, by laser energy proceeding nanoseconds prior to the main pulse. This causes the laser-absorption surface to be pushed back hundreds of microns from the initial target surface; thus increasing the distance that electrons must travel to reach the imploded core. Previous experiments have shown an order of magnitude decrease in coupling into surrogate targets when intentionally increasing the amount of preplasma. Additionally, for electrons to deposit energy within the core, they should have kinetic energies on the order of a few MeV, as less energetic electrons will be stopped prior to the core and more energetic electrons will pass through the core without depositing much energy. Thus a quantitative understanding of the electron energy spectrum and how it responds to varied laser parameters is paramount for fast ignition. For the first time, this dissertation quantitatively investigates the acceleration of electrons using an ultra-high-contrast laser. Ultra-high-contrast lasers reduce the laser energy that reaches the target prior to the main pulse; drastically reducing the amount of preplasma. Experiments were performed in a cone-wire geometry relevant to fast ignition. These experiments irradiated the inner-tip of a Au cone with the laser and observed electrons that passed through a Cu wire attached to the outer-tip of the cone. The total emission of Kalpha x-rays is used as a diagnostic to infer the electron energy coupled into the wire. Imaging the x-ray emission allowed an effective path-length of electrons within the wire to be determined, which constrained the electron energy spectrum. Experiments were carried out on the ultra-high-contrast Trident laser

Backscattering of projectile-bound electrons from solid surfaces

International Nuclear Information System (INIS)

Tobisch, M.; Schosnig, M.; Kroneberger, K.; Kuzel, M.; Maier, R.; Jung, M.; Fiedler, C.; Rothard, H.; Clouvas, A.; Suarez, S.; Groeneveld, K.O.

1994-01-01

The contribution of projectile ionization (PI) to secondary electron emission is studied by collision of H 2 + and H 3 + ions (400 keV/u and 700 keV/u) with carbon, copper and gold targets (600 A). The measured doubly differential intensity distribution shows a peak of lost projectile electrons near - v p . We describe the subtraction of the contribution of target ionization (TI), and compare the remaining electron intensities with a BEA calculation. For solids we observe a strong energy shift of the electron loss peak, which is compared with the influence of electron transport and binding energy. Furthermore, the low energy tail of the electron loss peak indicates the simultaneous occurrence of PI and TI. Finally we discuss the influence of surface conditions and the dependence of the observation angles on the measured electron intensities. (orig.)

Smoke emissions in small-scale burning of wood

International Nuclear Information System (INIS)

Tuomi, S.

1993-01-01

The article is based on research carried out in Finland and Sweden on the subject of emissions of smoke in the small-scale burning of wood and the factors affecting it. Due to incomplete combustion, small-scale burning of wood is particularly typified by its emissions of solid particles, carbon monoxide, hydrocarbons and PAH compounds. Included among factors influencing the volume of emissions are the load imposed on the heating device, the manner in which the fuel is fed into the firebox, fuel quality, and heating device structure. Emissions have been found to be at their minimum in connection with heating systems based on accumulators. Emissions can be significantly reduced by employing state-of-the-art technology, appropriate ways of heating and by dry fuel. A six-year bioenergy research programme was launched early in 1993 in Finland. All leading research institutions and enterprises participate in this programme. Reduction of emissions has been set as the central goal in the part dealing with small-scale burning of wood. Application of catalytic combustion in Finnish-made heating devices is one of the programmes development targets. Up to this date, the emissions produced in the small-scale burning of wood are not mentioned in official regulations pertaining to approved heating devices. In Sweden tar emissions are applied as a measure of the environmental impact imposed by heating devices

Anthropogenic mercury emissions from 1980 to 2012 in China.

Science.gov (United States)

Huang, Ying; Deng, Meihua; Li, Tingqiang; Japenga, Jan; Chen, Qianqian; Yang, Xiaoe; He, Zhenli

2017-07-01

China was considered the biggest contributor for airborne mercury in the world but the amount of mercury emission in effluents and solid wastes has not been documented. In this study, total national and regional mercury emission to the environment via exhaust gases, effluents and solid wastes were accounted with updated emission factors and the amount of goods produced and/or consumed. The national mercury emission in China increased from 448 to 2151 tons during the 1980-2012 period. Nearly all of the emissions were ended up as exhaust gases and solid wastes. The proportion of exhaust gases decreased with increasing share of solid wastes and effluents. Of all the anthropogenic sources, coal was the most important contributor in quantity, followed by mercury mining, gold smelting, nonferrous smelting, iron steel production, domestic wastes, and cement production, with accounting for more than 90% of the total emission. There was a big variation of regional cumulative mercury emission during 1980-2012 in China, with higher emissions occurred in eastern areas and lower values in the western and far northern regions. The biggest cumulative emission occurred in GZ (Guizhou), reaching 3974 t, while the smallest cumulative emission was lower than 10 t in XZ (Tibet). Correspondingly, mercury accumulation in soil were higher in regions with larger emissions in unit area. Therefore, it is urgent to reduce anthropogenic mercury emission and subsequent impact on ecological functions and human health. Copyright © 2017. Published by Elsevier Ltd.

Contrast-enhanced fluorodeoxyglucose positron emission tomography/computed tomography in solid pseudopapillary neoplasm of the pancreas

International Nuclear Information System (INIS)

Santhosh, Sampath; Lakshmanan, Ramesh Kumar; Sonik, Bhavay; Padmavathy, Rajagopalan; Gunaseelan, Rajamani Emmanuel

2016-01-01

Solid pseudopapillary neoplasm (SPN) of the pancreas is a rare pancreatic tumor with low malignant potential. It occurs characteristically more often in young women. Radiological and pathological studies have revealed that the tumor is quite different from other pancreatic tumors. Limited information is available in the literature reporting their accumulation of fluorine- 18 fluorodeoxyglucose ( 18 F-FDG) in positron emission tomography/computed tomography (PET/CT). Here, we report a case of pancreatic SPN imaged with contrast-enhanced FDG PET/CT. A percutaneous fine needle aspiration from the metabolically active lesion revealed SPN, and it was confirmed with histopathological results. Recurrence or metastasis was not found after 7 months of follow-up

Sectoral CO2 emissions in the Netherlands up to 2010. Update of the Reference Projection for Policy-making on Indicative Targets

NARCIS (Netherlands)

Boonekamp PGM; Daniels BW; Dril AWN van; Kroon P; Ybema JR; Wijngaart RA van den; ECN; KMD

2004-01-01

The Dutch government intends to formulate indicative targets for maximum sectoral CO2- emission levels in the year 2010. To this end the expected future emission levels have been determined for four sectors: Build Environment, Agriculture, Transportation and Industry/ Energy. The study relies

Synthesis of silver hollow nanoparticles and observation of photoluminescence emission properties

International Nuclear Information System (INIS)

Desarkar, H.S.; Kumbhakar, P.; Mitra, A.K.

2013-01-01

Preparation of hollow silver nanoparticles (HSNs) along-with solid silver nanoparticles are reported by Nd:YAG laser ablation of solid silver target immersed in water medium with a laser ablation time (LAT) duration of 50 min and with the incident laser fluence of 151 J/cm 2 . It is found that only solid silver nanoparticles are produced when the experiment is carried out with smaller values of LAT duration. The synthesized samples are characterized by using transmission electron microscopy and UV–Visible absorption spectroscopy. The UV–Visible absorption spectra of the samples show sharp absorptions in the ultraviolet and in visible regions due to interband transition and surface plasmon resonance oscillations in Ag nanoparticles, respectively. It is found that all samples exhibit photoluminescence (PL) emission, at room temperature, in the UV–Visible region peaked at ∼346 nm, due to the recombination of electrons with holes from sp conduction band to d band of Ag. The sample containing HSNs exhibits strong PL emission and the value of peak PL emission intensity is enhanced by the factor of 2.4 in comparison to that obtained from the sample synthesized with LAT duration of 20 min. The synthesized HSNs may find applications in catalysis and in chemical sensing. - Highlights: ►Hollow silver nanoparticles of 15–60 nm particle sizes are prepared by laser ablation. ►Prepared Ag nanoparticles show sharp absorptions in the UV and visible regions. ►Strong interband transition along-with SPR oscillations is reported. ►Enhancement (2.4 times) in photoluminescence emission in the UV region is reported.

Remote Monitoring of a Multi-Component Liquid-Phase Organic Synthesis by Infrared Emission Spectroscopy: The Recovery of Pure Component Emissivities by Band-Target Entropy Minimization

Czech Academy of Sciences Publication Activity Database

Cheng, S.; Tjahjono, M.; Rajarathnam, D.; Chuanzhao, L.; Lyapkalo, Ilya; Chen, D.; Garland, M.

2007-01-01

Roč. 61, č. 10 (2007), s. 1057-1062 ISSN 0003-7028 Institutional research plan: CEZ:AV0Z40550506 Keywords : infrared emission spectroscopy * liquid phase reaction * band-target entropy minimization * BTEM * emittance Subject RIV: CC - Organic Chemistry Impact factor: 1.902, year: 2007

Bipolar highly solid-state luminescent phenanthroimidazole derivatives as materials for blue and white organic light emitting diodes exploiting either monomer, exciplex or electroplex emission

OpenAIRE

Butkutė, Rita; Lygaitis, Ramūnas; Mimaitė, Viktorija; Gudeika, Dalius; Volyniuk, Dmytro; Sini, Gjergji; Gražulevičius, Juozas Vidas

2017-01-01

Four phenanthroimidazole-based bipolar compounds having electron-donating carbazole or diphenylamino moieties were synthesized and characterized. All compounds form glasses and exhibit high glass transition temperatures ranging from 183 to 239 °C. Solid state blue emission was detected for all synthesized compounds and quantum yields in solid state reached 0.55. Room temperature hole and electron mobilities in the layers of phenanthroimidazole derivatives reached 3.14 × 10−4 and 5.69 × 10−4 c...

Sub-microanalysis of solid samples with near-field enhanced atomic emission spectroscopy

Science.gov (United States)

Wang, Xiaohua; Liang, Zhisen; Meng, Yifan; Wang, Tongtong; Hang, Wei; Huang, Benli

2018-03-01

A novel approach, which we have chosen to name it as near-field enhanced atomic emission spectroscopy (NFE-AES), was proposed by introducing a scanning tunnelling microscope (STM) system into a laser-induced breakdown spectrometry (LIBS). The near-field enhancement of a laser-illuminated tip was utilized to improve the lateral resolution tremendously. Using the hybrid arrangement, pure metal tablets were analyzed to verify the performance of NFE-AES both in atmosphere and in vacuum. Due to localized surface plasmon resonance (LSPR), the incident electromagnetic field is enhanced and confined at the apex of tip, resulting in sub-micron scale ablation and elemental emission signal. We discovered that the signal-to-noise ratio (SNR) and the spectral resolution obtained in vacuum condition are better than those acquired in atmospheric condition. The quantitative capability of NFE-AES was demonstrated by analyzing Al and Pb in Cu matrix, respectively. Submicron-sized ablation craters were achieved by performing NFE-AES on a Si wafer with an Al film, and the spectroscopic information from a crater of 650 nm diameter was successfully obtained. Due to its advantage of high lateral resolution, NFE-AES imaging of micro-patterned Al lines on an integrated circuit of a SIM card was demonstrated with a sub-micron lateral resolution. These results reveal the potential of the NFE-AES technique in sub-microanalysis of solids, opening an opportunity to map chemical composition at sub-micron scale.

Greenhouse gas emissions from different municipal solid waste management scenarios in China: Based on carbon and energy flow analysis.

Science.gov (United States)

Liu, Yili; Sun, Weixin; Liu, Jianguo

2017-10-01

Waste management is a major source of global greenhouse gas (GHG) emissions and many opportunities exist to reduce these emissions. To identify the GHG emissions from waste management in China, the characteristics of MSW and the current and future treatment management strategies, five typical management scenarios were modeled by EaseTech software following the principles of life cycle inventory and analyzed based on the carbon and energy flows. Due to the high organic fraction (50-70%) and moisture content (>50%) of Chinese municipal solid waste (MSW), the net GHG emissions in waste management had a significant difference from the developed countries. It was found that the poor landfill gas (LFG) collection efficiency and low carbon storage resulted landfilling with flaring and landfilling with biogas recovery scenarios were the largest GHG emissions (192 and 117 kgCO 2 -Eq/t, respectively). In contrast, incineration had the best energy recovery rate (19%), and, by grid emissions substitution, led to a substantial decrease in net GHG emissions (-124 kgCO 2 -Eq/t). Due to the high energy consumption in operation, the unavoidable leakage of CH 4 and N 2 O in treatment, and the further release of CH 4 in disposing of the digested residue or composted product, the scenarios with biological treatment of the organic fractions after sorting, such as composting or anaerobic digestion (AD), did not lead to the outstanding GHG reductions (emissions of 32 and -36 kgCO 2 -Eq/t, respectively) as expected. Copyright © 2017. Published by Elsevier Ltd.

Laser-material interactions: A study of laser energy coupling with solids

Energy Technology Data Exchange (ETDEWEB)

Shannon, Mark Alan [Univ. of California, Berkeley, CA (United States)

1993-11-01

This study of laser-light interactions with solid materials ranges from low-temperature heating to explosive, plasma-forming reactions. Contained are four works concerning laser-energy coupling: laser (i) heating and (ii) melting monitored using a mirage effect technique, (iii) the mechanical stress-power generated during high-powered laser ablation, and (iv) plasma-shielding. First, a photothermal deflection (PTD) technique is presented for monitoring heat transfer during modulated laser heating of opaque solids that have not undergone phase-change. Of main interest is the physical significance of the shape, magnitude, and phase for the temporal profile of the deflection signal. Considered are the effects that thermophysical properties, boundary conditions, and geometry of the target and optical probe-beam have on the deflection response. PTD is shown to monitor spatial and temporal changes in heat flux leaving the surface due to changes in laser energy coupling. The PTD technique is then extended to detect phase-change at the surface of a solid target. Experimental data shows the onset of melt for indium and tin targets. The conditions for which melt can be detected by PTD is analyzed in terms of geometry, incident power and pulse length, and thermophysical properties of the target and surroundings. Next, monitoring high-powered laser ablation of materials with stress-power is introduced. The motivation for considering stress-power is given, followed by a theoretical discussion of stress-power and how it is determined experimentally. Experiments are presented for the ablation of aluminum targets as a function of energy and intensity. The stress-power response is analyzed for its physical significance. Lastly, the influence of plasma-shielding during high-powered pulsed laser-material interactions is considered. Crater size, emission, and stress-power are measured to determine the role that the gas medium and laser pulse length have on plasma shielding.

Laser-material interactions: A study of laser energy coupling with solids

International Nuclear Information System (INIS)

Shannon, M.A.; California Univ., Berkeley, CA

1993-11-01

This study of laser-light interactions with solid materials ranges from low-temperature heating to explosive, plasma-forming reactions. Contained are four works concerning laser-energy coupling: laser (i) heating and (ii) melting monitored using a mirage effect technique, (iii) the mechanical stress-power generated during high-powered laser ablation, and (iv) plasma-shielding. First, a photothermal deflection (PTD) technique is presented for monitoring heat transfer during modulated laser heating of opaque solids that have not undergone phase-change. Of main interest is the physical significance of the shape, magnitude, and phase for the temporal profile of the deflection signal. Considered are the effects that thermophysical properties, boundary conditions, and geometry of the target and optical probe-beam have on the deflection response. PTD is shown to monitor spatial and temporal changes in heat flux leaving the surface due to changes in laser energy coupling. The PTD technique is then extended to detect phase-change at the surface of a solid target. Experimental data shows the onset of melt for indium and tin targets. The conditions for which melt can be detected by PTD is analyzed in terms of geometry, incident power and pulse length, and thermophysical properties of the target and surroundings. Next, monitoring high-powered laser ablation of materials with stress-power is introduced. The motivation for considering stress-power is given, followed by a theoretical discussion of stress-power and how it is determined experimentally. Experiments are presented for the ablation of aluminum targets as a function of energy and intensity. The stress-power response is analyzed for its physical significance. Lastly, the influence of plasma-shielding during high-powered pulsed laser-material interactions is considered. Crater size, emission, and stress-power are measured to determine the role that the gas medium and laser pulse length have on plasma shielding

Defining a radiotherapy target with positron emission tomography

International Nuclear Information System (INIS)

Black, Quinten C.; Grills, Inga S.; Kestin, Larry L.; Wong, Ching-Yee O.; Wong, John W.; Martinez, Alvaro A.; Yan Di

2004-01-01

Purpose: F-18 fluorodeoxyglucose positron emission tomography (FDG-PET) imaging is now considered the most accurate clinical staging study for non-small-cell lung cancer (NSCLC) and is also important in the staging of multiple other malignancies. Gross tumor volume (GTV) definition for radiotherapy, however, is typically based entirely on computed tomographic data. We performed a series of phantom studies to determine an accurate and uniformly applicable method for defining a GTV with FDG-PET. Methods and materials: A model-based method was tested by a phantom study to determine a threshold, or unique cutoff of standardized uptake value based on body weight (standardized uptake value [SUV]) for FDG-PET based GTV definition. The degree to which mean target SUV, background FDG concentration, and target volume influenced that GTV definition were evaluated. A phantom was constructed consisting of a 9.0-L cylindrical tank. Glass spheres with volumes ranging from 12.2 to 291.0 cc were suspended within the tank, with a minimum separation of 4 cm between the edges of the spheres. The sphere volumes were selected based on the range of NSCLC patient tumor volumes seen in our clinic. The tank and spheres were filled with a variety of known concentrations of FDG in several experiments and then scanned using a General Electric Advance PET scanner. In the initial experiment, six spheres with identical volumes were filled with varying concentrations of FDG (mean SUV 1.85 ∼ 9.68) and suspended within a background bath of FDG at a similar concentration to that used in clinical practice (0.144 μCi/mL). The second experiment was identical to the first, but was performed at 0.144 and 0.036 μCi/mL background concentrations to determine the effect of background FDG concentration on sphere definition. In the third experiment, six spheres with volumes of 12.2 to 291.0 cc were filled with equal concentrations of FDG and suspended in a standard background FDG concentration of 0.144 �

Correcting for variable laser-target distances of laser-induced breakdown spectroscopy measurements with ChemCam using emission lines of Martian dust spectra

Energy Technology Data Exchange (ETDEWEB)

Melikechi, N.; Mezzacappa, A. [Optical Science Center for Applied Research, Delaware State University, Dover, DE (United States); Cousin, A.; Lanza, N.L. [Los Alamos National Laboratory, Los Alamos, NM (United States); Lasue, J. [Institut de Recherche en Astophysique et Planetologie (IRAP), Universite' Paul Sabatier, Toulouse (France); Clegg, S.M. [Los Alamos National Laboratory, Los Alamos, NM (United States); Berger, G. [Institut de Recherche en Astophysique et Planetologie (IRAP), Universite' Paul Sabatier, Toulouse (France); Wiens, R.C. [Los Alamos National Laboratory, Los Alamos, NM (United States); Maurice, S. [Institut de Recherche en Astophysique et Planetologie (IRAP), Universite' Paul Sabatier, Toulouse (France); Tokar, R.L.; Bender, S. [Planetary Science Institute, Flagstaff, AZ (United States); Forni, O. [Institut de Recherche en Astophysique et Planetologie (IRAP), Universite' Paul Sabatier, Toulouse (France); Breves, E.A.; Dyar, M.D. [Dept. of Astronomy, Mount Holyoke College, South Hadley, MA (United States); Frydenvang, J. [The Niels Bohr Institute, University of Copenhagen, Copenhagen (Denmark); Delapp, D. [Los Alamos National Laboratory, Los Alamos, NM (United States); Gasnault, O. [Institut de Recherche en Astophysique et Planetologie (IRAP), Universite' Paul Sabatier, Toulouse (France); Newsom, H.; Ollila, A.M. [Earth and Planetary Sciences, University of New Mexico, Alburquerque, NM (United States); Lewin, E. [Institut des Sciences de la Terre, Universite Grenoble l-CNRS, Grenoble (France); and others

2014-06-01

As part of the Mars Science Laboratory, the ChemCam instrument acquires remote laser induced breakdown spectra at distances that vary between 1.56 m and 7 m. This variation in distance affects the intensities of the measured LIBS emission lines in non-trivial ways. To determine the behavior of a LIBS emission line with distance, it is necessary to separate the effects of many parameters such as laser energy, laser spot size, target homogeneity, and optical collection efficiency. These parameters may be controlled in a laboratory on Earth but for field applications or in space this is a challenge. In this paper, we show that carefully selected ChemCam LIBS emission lines acquired from the Martian dust can be used to build an internal proxy spectroscopic standard. This in turn, allows for a direct measurement of the effects of the distance of various LIBS emission lines and hence can be used to correct ChemCam LIBS spectra for distance variations. When tested on pre-launch LIBS calibration data acquired under Martian-like conditions and with controlled and well-calibrated targets, this approach yields much improved agreement between targets observed at various distances. This work lays the foundation for future implementation of automated routines to correct ChemCam spectra for differences caused by variable distance. - Highlights: • Selected Martian dust emission lines are used to correct for variable laser-target distances. • The correction model yields improved agreement between targets observed at various distances. • The impact of the model reduces the bias between predicted and actual compositions by as much as 70%. • When implemented, the model will yield spectral corrections for various ChemCam measurements. • This work is a foundation to perform novel stand-off LIBS measurements on Earth and other planets.

Analytical solutions for thermal transient profile in solid target irradiated with low energy and high beam current protons

International Nuclear Information System (INIS)

Oliveira, Henrique B. de; Brazao, Nei G.; Sciani, Valdir

2009-01-01

There were obtained analytical solutions for thermal transient in solid targets, used in short half-life radioisotopes production, when irradiated with low energy and high beam current protons, in the cyclotron accelerator Cyclone 30 of the Institute for Energy and Nuclear Research (IPEN/CNEN-SP). The beam spatial profile was considered constant and the time depended heat distribution equation was resolved for a continuous particles flow entering the target. The problem was divided into two stages: a general solution was proposed which is the sum of two functions, the first one related to the thermal equilibrium situation and the second one related to a time dependent function that was determinate by the setting of the contour conditions and the initial conditions imposed by the real problem. By that one got an analytic function for a complete description of the heat transport phenomenon inside the targets. There were used both, numerical and symbolic computation methods, to obtain temperature maps and thermal gradients and the results showed an excellent agreement when compared with purely numerical models. The results were compared with obtained data from Gallium-67 and Thallium-201 irradiation routines conducted by the IPEN Cyclotrons accelerators center, showing excellent agreement. The objective of this paper is to develop solid targets irradiation systems (metals and oxides) so that one can operate with high levels of current beam, minimizing the irradiation time and maximizing the final returns. (author)

Observation of heavy cluster emission from radioactive 230U nuclei

International Nuclear Information System (INIS)

Pan Qiangyan; Yuan Shuanggui; Yang Weifan; Li Zongwei; Ma Taotao; Guo Junsheng; Liu Mingyi; Liu Hongye; Xu Shuwei; Gan Zaiguo; Kong Dengming; Qiao Jimin; Luo Zihua; Zhang Mutian; Wang Shuhong

1999-01-01

230 Pa was produced with the reaction 232 Th (p, 3n) 230 Pa in the irradiation powder targets of ThO 2 with 35 MeV proton beam. Sources of 230 Pa→ 230 U + β - were prepared by radiochemical method. Using solid-state track registration detectors, two events of 230 U decay with heavy cluster emission have been observed. The preliminary branching ratio to α-decay comes out to be B = λ Ne /λ α = (1.3 ± 0.8) x 10 -14

X-ray yields by low energy heavy ion excitation in alkali halide solid targets

International Nuclear Information System (INIS)

Kurup, M.B.; Prasad, K.G.; Sharma, R.P.

1981-01-01

Solid targets of the alkali halides KCl, NaCl and KBr are bombarded with ion beams of 35 Cl + , 40 Ar + and 63 Cu + in the energy range 165 keV to 320 keV. The MO and characteristic K X-ray yields resulting from the ion-atom collision have been systematically studied. Both MO and Cl K X-ray yields are enhanced by factors 3.5 and 2 respectively in KCl targets as compared to that in NaCl when bombarded with either Cl + or Ar + projectiles. An intercomparison of MO and K X-ray yields for a given projectile-target combination has shown that the latter increases ten times faster than the former as the energy of the projectile is increased from 165 to 320 keV indicating a correspondingly stronger velocity dependence of the K X-ray production process. The X-ray yields observed in the symmetric Cl-Cl collision are identical to those observed in the asymmetric Ar-Cl collision for the same projectile velocities in both KCl and NaCl targets. It is inferred that the multiple ionization of the projectile resulting in an increase in the binding energy of its inner shells offsets the expected enhancement in the X-ray yields in a symmetric collision. The same projectiles, Ar or Cl, incident on KBr targets have produced only Br L X-rays. Using substantially heavier projectiles than the target atoms (Na, K and Cl), like 63 Cu + ions, the inner shell excitation by recoiling atoms is shown. (orig.)

Pion emission from the T2K replica target: method, results and application

CERN Document Server

Abgrall, N.; Anticic, T.; Antoniou, N.; Argyriades, J.; Baatar, B.; Blondel, A.; Blumer, J.; Bogomilov, M.; Bravar, A.; Brooks, W.; Brzychczyk, J.; Bubak, A.; Bunyatov, S.A.; Busygina, O.; Christakoglou, P.; Chung, P.; Czopowicz, T.; Davis, N.; Debieux, S.; Di Luise, S.; Dominik, W.; Dumarchez, J.; Dynowski, K.; Engel, R.; Ereditato, A.; Esposito, L.S.; Feofilov, G.A.; Fodor, Z.; Ferrero, A.; Fulop, A.; Gazdzicki, M.; Golubeva, M.; Grabez, B.; Grebieszkow, K.; Grzeszczuk, A.; Guber, F.; Haesler, A.; Hakobyan, H.; Hasegawa, T.; Idczak, R.; Igolkin, S.; Ivanov, Y.; Ivashkin, A.; Kadija, K.; Kapoyannis, A.; Katrynska, N.; Kielczewska, D.; Kikola, D.; Kirejczyk, M.; Kisiel, J.; Kiss, T.; Kleinfelder, S.; Kobayashi, T.; Kochebina, O.; Kolesnikov, V.I.; Kolev, D.; Kondratiev, V.P.; Korzenev, A.; Kowalski, S.; Krasnoperov, A.; Kuleshov, S.; Kurepin, A.; Lacey, R.; Larsen, D.; Laszlo, A.; Lyubushkin, V.V.; Mackowiak-Pawlowska, M.; Majka, Z.; Maksiak, B.; Malakhov, A.I.; Maletic, D.; Marchionni, A.; Marcinek, A.; Maris, I.; Marin, V.; Marton, K.; Matulewicz, T.; Matveev, V.; Melkumov, G.L.; Messina, M.; Mrowczynski, St.; Murphy, S.; Nakadaira, T.; Nishikawa, K.; Palczewski, T.; Palla, G.; Panagiotou, A.D.; Paul, T.; Peryt, W.; Petukhov, O.; Planeta, R.; Pluta, J.; Popov, B.A.; Posiadala, M.; Pulawski, S.; Puzovic, J.; Rauch, W.; Ravonel, M.; Renfordt, R.; Robert, A.; Rohrich, D.; Rondio, E.; Rossi, B.; Roth, M.; Rubbia, A.; Rustamov, A.; Rybczynski, M.; Sadovsky, A.; Sakashita, K.; Savic, M.; Sekiguchi, T.; Seyboth, P.; Shibata, M.; Sipos, M.; Skrzypczak, E.; Slodkowski, M.; Staszel, P.; Stefanek, G.; Stepaniak, J.; Strabel, C.; Strobele, H.; Susa, T.; Szuba, M.; Tada, M.; Taranenko, A.; Tereshchenko, V.; Tolyhi, T.; Tsenov, R.; Turko, L.; Ulrich, R.; Unger, M.; Vassiliou, M.; Veberic, D.; Vechernin, V.V.; Vesztergombi, G.; Wilczek, A.; Wlodarczyk, Z.; Wojtaszek-Szwarc, A.; Wyszynski, O.; Zambelli, L.; Zipper, W.; Hartz, M.; Ichikawa, A.K.; Kubo, H.; Marino, A.D.; Matsuoka, K.; Murakami, A.; Nakaya, T.; Suzuki, K.; Yuan, T.; Zimmerman, E.D.

2013-01-01

The T2K long-baseline neutrino oscillation experiment in Japan needs precise predictions of the initial neutrino flux. The highest precision can be reached based on detailed measurements of hadron emission from the same target as used by T2K exposed to a proton beam of the same kinetic energy of 30 GeV. The corresponding data were recorded in 2007-2010 by the NA61/SHINE experiment at the CERN SPS using a replica of the T2K graphite target. In this paper details of the experiment, data taking, data analysis method and results from the 2007 pilot run are presented. Furthermore, the application of the NA61/SHINE measurements to the predictions of the T2K initial neutrino flux is described and discussed.

K-α emission form medium and high-Z materials irradiated by femtosecond laser pulses

International Nuclear Information System (INIS)

Limpouch, J.; Klimo, O.; Zhavoronkov, N.; Andreev, A.A.

2006-01-01

Complete test of publication follows. Fast electrons are created at the target surface during the interaction of high intensity ultra short laser pulses with solids. Fast electrons penetrate deep into the target where they generate K-α and Bremsstrahlung radiation. Generated high brightness K-α pulses offer the prospect of creating a cheap and compact X-ray source, posing a promising alternative to synchrotron radiation, e.g. in medical application and in material science. With an increase in laser intensity, efficient X-ray emission in the multi-keV range with pulse duration shorter than few picoseconds is expected. This short incoherent but monochromatic X-ray emission synchronized with laser pulses may be used for time-resolved measurements. Acceleration of fast electrons, their transport and K-α photon generation and emission from the target surface in both forward and backward directions are studied here numerically. The results are compared to recent experiments studying K-α emission from the front and rear surface of copper foil targets of various thicknesses and for various parameters of the laser plasma interaction. One-dimensional PIC simulations coupled with 3D time-resolved Monte Carlo simulations show that account of ionization processes and of density profile formed by laser ASE emission is essential for reliable explanation of experimental data. While sub-relativistic intensities are optimum for laser energy transformation into K-α emission for medium-Z targets, relativistic laser intensities have to be used for hard X-ray generation in high-Z materials. The cross-section for K-α shell ionization of high-Z elements by electrons increases or remains approximately constant within a factor of two at relativistic electron energies up to electron energies in the 100-MeV range. Moreover, the splitting ratio of K-α photon emission to Auger electron emission is favorable for high-Z materials, and thus efficient K-α emission is possible. In our

Greenhouse gas emissions of motor vehicles in Chinese cities and the implication for China’s mitigation targets

International Nuclear Information System (INIS)

Zeng, Yuan; Tan, Xianchun; Gu, Baihe; Wang, Yi; Xu, Baoguang

2016-01-01

Highlights: • Predict baseline GHG emissions of different motor vehicles of Chinese cities. • Different kinds of fuels are considered when accounting GHG emissions. • A comparative analysis on four case cities of China is conducted. • New energy will have different growth patterns due to diverse policies and resources. • Policy implications are given based on the analysis results. - Abstract: Along with rapid development of economy, urbanization and industrialization in China, the transportation sector especially road transport accounts for the quickest growth of energy consumption and greenhouse gas (GHG) emissions across the country. This paper selects four representative cities (Beijing, Shanghai, Guangzhou, and Chongqing) in the north, east, south, and west of China as targets of case study. It predicts future motor vehicle population in various cities using the Gompertz Model, and predicts and analyzes fuel consumption and GHG emissions of different types of motor vehicles in the case cities by 2035. The results indicate that besides gasoline and diesel, in the future uses of various types of vehicle fuels will follow different patterns among these four cities due to diverse resources endowment, economic strength, technology levels and geographical features. Based on predicted vehicle population and fuel consumption, it is found that from 2013 to 2035, GHG emissions from tank to wheel (TTW) and well to wheel (WTW) in all cities will continuously increase yet at different rates. If there is no interference from new policies, around 2020 Chongqing is expected to replace Beijing as the city with the highest volume of GHG emissions of vehicles among four case study cities. Therefore, the four cities especially Chongqing need urgently to develop or adjust low-carbon policies in road transportation sector, in order to achieve China’s future greenhouse gas reduction targets. Some policy implications to reduce GHG emissions of the road transportation

Hot muonic deuterium and tritium from cold targets

International Nuclear Information System (INIS)

Marshall, G.M.; Beveridge, J.L.; Bailey, J.M.; Beer, G.A.; Knowles, P.E.; Mason, G.R.; Olin, A.; Brewer, J.H.; Forster, B.M.; Huber, T.M.; Pippitt, B.; Jacot-Guillarmod, R.; Schellenberg, L.; Martoff, C.J.; Petitjean, C.

1992-01-01

Experiments are described which use a solid hydrogen layer to form muonic hydrogen isotopes in vacuum. The method relies on transfer of the muon from protium to either a deuteron or a triton. The resulting muonic deuterium or muonic tritium will not immediately thermalize because of the very low elastic cross sections, and may be emitted from the surface of the layer. Measurements which detect decay electrons, muonic x-rays, and fusion products have been used to study the processes. A target has been constructed which exploits muonic atom emission in order to study the energy dependence of transfer and muon molecular formation

The Little Heat Engine: Heat Transfer in Solids, Liquids and Gases

Directory of Open Access Journals (Sweden)

Robitaille P.-M.

2007-10-01

Full Text Available In this work, an introductory exposition of the laws of thermodynamics and radiative heat transfer is presented while exploring the concepts of the ideal solid, the lattice, and the vibrational, translational, and rotational degrees of freedom. Analysis of heat transfer in this manner helps scientists to recognize that the laws of thermal radiation are strictly applicable only to the ideal solid. On the Earth, such a solid is best represented by either graphite or soot. Indeed, certain forms of graphite can approach perfect absorption over a relatively large frequency range. Nonetheless, in dealing with heat, solids will eventually sublime or melt. Similarly, liquids will give way to the gas phase. That thermal conductivity eventually decreases in the solid signals an inability to further dissipate heat and the coming breakdown of Planck’s law. Ultimately, this breakdown is reflected in the thermal emission of gases. Interestingly, total gaseous emissivity can de- crease with increasing temperature. Consequently, neither solids, liquids, or gases can maintain the behavior predicted by the laws of thermal emission. Since the laws of thermal emission are, in fact, not universal, the extension of these principles to non-solids constitutes a serious overextension of the work of Kirchhoff, Wien, Stefan and Planck.

Evidence for heavy ion emission of 230U

International Nuclear Information System (INIS)

Pan Qiangyan; Yang Weifan; Yuan Shuanggui; Li Zongwei; Ma Taotao; Guo Junsheng; Liu Mingyi; Liu Hongye; Xu Shuwei; Gan Zaiguo; Kong Dengming; Qiao Jimin; Luo Zihua; Zhang Mutian; Wang Shuhong

1999-01-01

Radioisotope of 230 Pa was synthesized by proton irradiation of ThO 2 powder targets with thickness of about 2g/cm 2 . Pure 230 Pa was extracted and deep purified from thorium and fission products by the radiochemical method. Thin 230 Pa→ 230 U sources were prepared for measuring the cluster decay of 230 U. Two cases of decay via heavy ion emission, which were most probably for the neon decays of 230 U, were detected by using solid-state track registration detectors. The preliminary branching ratio relative to α-decay comes out to be (1.3 +- 0.8) x 10 -14

Improved age-diffusion model for low-energy electron transport in solids. II. Application to secondary emission from aluminum

International Nuclear Information System (INIS)

Dubus, A.; Devooght, J.; Dehaes, J.C.

1987-01-01

The ''improved age-diffusion'' model for secondary-electron transport is applied to aluminum. Electron cross sections for inelastic collisions with the free-electron gas using the Lindhard dielectric function and for elastic collisions with the randomly distributed ionic cores are used in the calculations. The most important characteristics of backward secondary-electron emission induced by low-energy electrons on polycrystalline Al targets are calculated and compared to experimental results and to Monte Carlo calculations. The model appears to predict the electronic yield, the energy spectra, and the spatial dependence of secondary emission with reasonable accuracy

Enhanced solid state emission of quinoline derivatives for fluorescent sensors

Energy Technology Data Exchange (ETDEWEB)

Kim, Hyong-Jun, E-mail: hkim@kongju.ac.kr

2016-08-15

Excited-state intramolecular proton transfer (ESIPT) molecules are of utmost interest in the fields of organic light emitting diode, photo-patterning, chemosensor, proton transfer laser, and photostabilizer. Fine control of the functional substituents as well as the molecular structure of core ESIPT unit is primarily demanded for specific applications. Here, the photophysics of quinoline derivatives of 2-quinolin-2-yl-phenol and 2-(8-chloroquinolin-2-yl)phenol is explored. Straightening the twist between the hydroxyphenyl and the quinoline moieties with the aid of the hydrogen bonding promoted the excited energy to flow through a radiative decay pathway via proton transfer to the nitrogen. Furthermore, close molecular packing of J-aggregates and thus resulted vibration restriction in a dense matter opens an ESIPT corridor and is characterized to show enhanced emission. The mechanism is applied to the selective Cu{sup 2+} or Fe{sup 2+} cation detection and further immunofluorescence labeling using avidin–biotin protein specific binding is demonstrated with the aid of nano self-assembly technique. - Highlights: • New orange fluorescent hydroxyphenylquinoline derivative was synthesized. • Molecular structure planarization induced enhanced fluorescence with large Stokes' shift. • Selective solution phase cation detection and solid state bio-sensing were demonstrated successfully.

The application of positron emission tomography/computed tomography in radiation treatment planning: effect on gross target volume definition and treatment management.

Science.gov (United States)

Iğdem, S; Alço, G; Ercan, T; Unalan, B; Kara, B; Geceer, G; Akman, C; Zengin, F O; Atilla, S; Okkan, S

2010-04-01

To analyse the effect of the use of molecular imaging on gross target volume (GTV) definition and treatment management. Fifty patients with various solid tumours who underwent positron emission tomography (PET)/computed tomography (CT) simulation for radiotherapy planning from 2006 to 2008 were enrolled in this study. First, F-18 fluorodeoxyglucose (FDG)-PET and CT scans of the treatment site in the treatment position and then a whole body scan were carried out with a dedicated PET/CT scanner and fused thereafter. FDG-avid primary tumour and lymph nodes were included into the GTV. A multidisciplinary team defined the target volume, and contouring was carried out by a radiation oncologist using visual methods. To compare the PET/CT-based volumes with CT-based volumes, contours were drawn on CT-only data with the help of site-specific radiologists who were blind to the PET/CT results after a median time of 7 months. In general, our PET/CT volumes were larger than our CT-based volumes. This difference was significant in patients with head and neck cancers. Major changes (> or =25%) in GTV delineation were observed in 44% of patients. In 16% of cases, PET/CT detected incidental second primaries and metastatic disease, changing the treatment strategy from curative to palliative. Integrating functional imaging with FDG-PET/CT into the radiotherapy planning process resulted in major changes in a significant proportion of our patients. An interdisciplinary approach between imaging and radiation oncology departments is essential in defining the target volumes. Copyright 2010 The Royal College of Radiologists. Published by Elsevier Ltd. All rights reserved.

Emissions Trading

NARCIS (Netherlands)

Woerdman, Edwin; Backhaus, Juergen

2014-01-01

Emissions trading is a market-based instrument to achieve environmental targets in a cost-effective way by allowing legal entities to buy and sell emission rights. The current international dissemination and intended linking of emissions trading schemes underlines the growing relevance of this

Can we bet on negative emissions to achieve the 2°C target even under strong carbon cycle feedbacks?

Science.gov (United States)

Tanaka, K.; Yamagata, Y.; Yokohata, T.; Emori, S.; Hanaoka, T.

2015-12-01

Negative emission technologies such as Bioenergy with Carbon dioxide Capture and Storage (BioCCS) play an ever more crucial role in meeting the 2°C stabilization target. However, such technologies are currently at their infancy and their future penetrations may fall short of the scale required to stabilize the warming. Furthermore, the overshoot in the mid-century prior to a full realization of negative emissions would give rise to a risk because such a temporal but excessive warming above 2°C might amplify itself by strengthening climate-carbon cycle feedbacks. It has not been extensively assessed yet how carbon cycle feedbacks might play out during the overshoot in the context of negative emissions. This study explores how 2°C stabilization pathways, in particular those which undergo overshoot, can be influenced by carbon cycle feedbacks and asks their climatic and economic consequences. We compute 2°C stabilization emissions scenarios under a cost-effectiveness principle, in which the total abatement costs are minimized such that the global warming is capped at 2°C. We employ a reduced-complexity model, the Aggregated Carbon Cycle, Atmospheric Chemistry, and Climate model (ACC2), which comprises a box model of the global carbon cycle, simple parameterizations of the atmospheric chemistry, and a land-ocean energy balance model. The total abatement costs are estimated from the marginal abatement cost functions for CO2, CH4, N2O, and BC.Our preliminary results show that, if carbon cycle feedbacks turn out to be stronger than what is known today, it would incur substantial abatement costs to keep up with the 2°C stabilization goal. Our results also suggest that it would be less expensive in the long run to plan for a 2°C stabilization pathway by considering strong carbon cycle feedbacks because it would cost more if we correct the emission pathway in the mid-century to adjust for unexpectedly large carbon cycle feedbacks during overshoot. Furthermore, our

Tailoring Nd3+ emission spectrum by a neodymium-doped tellurite all-solid photonic bandgap fiber

Science.gov (United States)

Tong, Hoang Tuan; Demichi, Daisuke; Suzuki, Takenobu; Ohishi, Yasutake

2018-02-01

A tellurite all-solid photonic bandgap fiber (ASPBF) whose cladding consists of 60 high-index rods arranged periodically around a central core was successfully fabricated. The diameter of high-index rod was about 5.0 μm and the distance between the center of two adjacent high-index rods was approximately 8.0 μm. The high-index rod was made of the TeO2-Li2O-WO3-MoO3-Nb2O5 (TLWMN) glass, the cladding was made of the TeO2-ZnO-Na2O-La2O3 (TZNL) glass as the background glass material and the central core was made of TZNL glass doped with 0.5 wt% of Nd2O3. A supercontinuum light from 0.6 to 2.4 μm was coupled into the core of fiber which is 2.2 cm long to measure its transmission spectrum. High transmission bands were obtained in the vicinity of 0.75 and 1.3 μm but the transmission was suppressed in the wavelength range from 1.0 to 1.06 μm. When a titanium∶Sapphire laser source at 0.75 μm was used, the emission spectrum was obtained with two peaks at 1.06 and 1.33 μm which are attributed to the 4F3/2->4I11/2 and 4F3/2->4I13/2 transitions of Nd3+ ion, respectively. The intensities of those emission peaks were compared with those obtained from a bulk glass having the same doping concentration of Nd3+. The results showed that by using tellurite ASPBF, the intensity of the 1.06-μm emission was suppressed by one-twelfth but the intensity of the 1.33-μm emission was maintained. This feature is very advantageous to filter out the 1.06-μm emission of Nd3+ ion in order to realize practical amplifier devices at 1.3 μm.

Technological methods of reducing the emissions of nitrogen oxides during the combustion of solid fuel

Energy Technology Data Exchange (ETDEWEB)

Kotler, V.R.

1981-01-01

For protecting the atmosphere from emissions of toxic NO /SUB x/ during combustion of fuel in boilers the amount of NO /SUB x/ can be reduced in the process of combustion, or the flue gases (FG) from the boiler can be cleaned. The latter method is bound up with the necessity for treatment of a large quantity of FG with a comparatively low concentration in them of nitrogen oxides, chemically stable and poorly soluble in water. The problem is complicated by the presence in the FG of SO /SUB x/, O/sub 2/, and solid particles. The method of purifying the FG is complicated and requires large capital investment and operating expenses. By laboratory studies in the All-Union Institute of Heat Engineering im. F.E. Dzerzhinskiy (VTI) it was established that thermal NO /SUB x/ is formed at a combustion temperature greater than or equal to 1550 /sup 0/C and that the 0/sub 2/ concentration and considerably less the temperature strongly affect NO /SUB x/ formation. On the basis of laboratory studies and industrial tests in the VTI, methods of reducing NO /SUB x/ emissions by large-scale boilers are recommended.

Waste Management Pinch Analysis (WAMPA): Application of Pinch Analysis for greenhouse gas (GHG) emission reduction in municipal solid waste management

International Nuclear Information System (INIS)

Ho, Wai Shin; Hashim, Haslenda; Lim, Jeng Shiun; Lee, Chew Tin; Sam, Kah Chiin; Tan, Sie Ting

2017-01-01

Highlights: • A novel method known as Waste Management Pinch Analysis (WAMPA) is presented. • WAMPA aims to identify waste management strategies based on specific target. • WAMPA is capable to examine the capacity of waste management strategies through graphical representation. - Abstract: Improper waste management happened in most of the developing country where inadequate disposal of waste in landfill is commonly practiced. Apart from disposal, MSW can turn into valuable product through recycling, energy recovery, and biological recovery action as suggested in the hierarchy of waste management. This study presents a method known as Waste Management Pinch Analysis (WAMPA) to examine the implication of a dual-objective – landfill and GHG emission reduction target in sustainable waste management. WAMPA is capable to identify the capacity of each waste processing strategy through graphical representation. A general methodology of WAMPA is presented through a demonstration of a SWM case followed by a detailed representation of WAMPA for five waste types. Application of the WAMPA is then applied on a case study for sustainable waste management planning from year 2015 to 2035. Three waste management strategies are incorporated into the case study – landfill, Waste-to-Energy (WtE), and reduce, reuse, and recycle (3R). The results show a 13.5% of total GHG emission reduction and 54.6% of total reduction of landfill are achieved. The major contributor of GHG emission which are from food waste (landfill emission) and plastic (WtE emission) is reduced.

Comparative Assessment of Particulate Air Pollution Exposure from Municipal Solid Waste Incinerator Emissions

Science.gov (United States)

Ashworth, Danielle C.; Fuller, Gary W.; Toledano, Mireille B.; Font, Anna; Elliott, Paul; Hansell, Anna L.; de Hoogh, Kees

2013-01-01

Background. Research to date on health effects associated with incineration has found limited evidence of health risks, but many previous studies have been constrained by poor exposure assessment. This paper provides a comparative assessment of atmospheric dispersion modelling and distance from source (a commonly used proxy for exposure) as exposure assessment methods for pollutants released from incinerators. Methods. Distance from source and the atmospheric dispersion model ADMS-Urban were used to characterise ambient exposures to particulates from two municipal solid waste incinerators (MSWIs) in the UK. Additionally an exploration of the sensitivity of the dispersion model simulations to input parameters was performed. Results. The model output indicated extremely low ground level concentrations of PM10, with maximum concentrations of incinerator characteristics, magnitude of emissions, and surrounding meteorological and topographical conditions are considered. Reducing exposure misclassification is particularly important in environmental epidemiology to aid detection of low-level risks. PMID:23935644

New Commitment Options: Compatibility with Emissions Trading

Energy Technology Data Exchange (ETDEWEB)

NONE

2006-07-01

This paper considers different options for quantitative greenhouse gas emission commitments from the standpoint of their technical compatibility with emissions trading. These are dynamic targets, binding targets with price caps, non-binding targets, sector-wide targets/mechanisms, action targets, allowances and endowments, and long-term permits. This paper considers these options from the standpoint of their compatibility with emissions trading.

Cooking with Fire: The Mutagenicity- and PAH-Emission ...

Science.gov (United States)

Emissions from solid fuels used for cooking cause ~4 million premature deaths per year. Advanced solid-fuel cookstoves are a potential solution, but they should be assessed by appropriate performance indicators, including biological effects. We evaluated two categories of solid-fuel cookstoves for 8 pollutant- and 4 mutagenicity-emission factors, correlated the mutagenicity-emission factors, and compared them to those of other combustion emissions. We burned red oak in a 3-stone fire (TSF), a natural-draft stove (NDS), and a forced-draft stove (FDS); we combusted propane as a liquified petroleum gas control fuel. We determined emission factors based on useful energy (megajoules delivered, MJd) for carbon monoxide, nitrogen oxides (NOx), black carbon, methane, total hydrocarbons, 32 polycyclic aromatic hydrocarbons, PM2.5, levoglucosan (a wood-smoke marker), and mutagenicity in Salmonella. Other than NOx the emission factors per MJd correlated highly among each other (r2 ≥ 0.92); NOx correlated 0.58-0.76 with the other emission factors. Excluding NOx, the NDS and FDS reduced the emission factors on average 68 and 92%, respectively, relative to the TSF. Nonetheless, the mutagenicity-emission factor based on fuel energy used (MJthermal) for the most efficient stove (FDS) was intermediate to that of a large diesel bus engine and a small diesel generator. Both mutagenicity- and pollutant-emission factors may be informative for characterizing cookstove

Experimental study on energy distribution of the hot electrons generated by femtosecond laser interacting with solid targets

International Nuclear Information System (INIS)

Gu Yuqiu; Zheng Zhijian; Zhou Weimin; Wen Tianshu; Chunyu Shutai; Cai Dafeng; Sichuan Univ., Chengdu; Neijiang Teachers College, Neijiang; Jiao Chunye; Chen Hao; Sichuan Univ., Chengdu; Yang Xiangdong

2005-01-01

This paper reports the results of the experiment of hot electron energy distribution during the femtosecond laser-solid target interaction. The hot electrons formed an anisotropic energy distribution. In the direction of the target normal, the energy spectrum of the hot electron was a Maxwellian-like distribution with an effective temperature of 206 keV, which was due to the resonance absorption. In the direction of the specular reflection of laser, there appeared a local plateau of hot electron energy spectrum at the beginning and then it was decreased gradually, which maybe produced by several acceleration mechanisms. The effective temperature and the yield of hot electrons in the direction of the target normal is larger than those in the direction of the specular reflection of laser, which proves that the resonance absorption mechanism is more effective than others. (authors)

Relativistic electron beam interaction and $K_{\\alpha}$-generation in solid targets

CERN Document Server

Fill, E; Eder, D; Eidmann, K; Saemann, A

1999-01-01

When fs laser pulses interact with solid surfaces at intensities I lambda /sup 2/ >10/sup 18/ W/cm/sup 2/ mu m/sup 2/, collimated relativistic electron beams are generated. These electrons can be used for producing intense X-radiation (bremsstrahlung or K/sub alpha /) for pumping an innershell X-ray laser. The basic concept of such a laser involves the propagation of the electron beam in a material which converts electron energy into appropriate pump photons. Using the ATLAS titanium-sapphire laser at Max-Planck-Institut fur Quantenoptik, we investigate the generation of hot electrons and of characteristic radiation in copper. The laser (200 mJ/130 fs) is focused by means of an off-axis parabola to a diameter of about 10 mu m. By varying the position of the focus, we measure the copper K/sub alpha /-yield as a function of intensity in a range from 10/sup 15/ to 2 x 10/sup 18/ W/cm/sup 2/ while keeping the laser pulse energy constant. Surprisingly, the highest emission is obtained at an intensity of about 10/s...

Double pulse laser induced breakdown spectroscopy of a solid in water: Effect of hydrostatic pressure on laser induced plasma, cavitation bubble and emission spectra

Science.gov (United States)

López-Claros, M.; Dell'Aglio, M.; Gaudiuso, R.; Santagata, A.; De Giacomo, A.; Fortes, F. J.; Laserna, J. J.

2017-07-01

There is a growing interest in the development of sensors use in exploration of the deep ocean. Techniques for the chemical analysis of submerged solids are of special interest, as they show promise for subsea mining applications where a rapid sorting of materials found in the sea bottom would improve efficiency. Laser-Induced Breakdown Spectroscopy (LIBS) has demonstrated potential for this application thanks to its unique capability of providing the atomic composition of submerged solids. Here we present a study on the parameters that affect the spectral response of metallic targets in an oceanic pressure environment. Following laser excitation of the solid, the plasma persistence and the cavitation bubble size are considerably reduced as the hydrostatic pressure increases. These effects are of particular concern in dual pulse excitation as reported here, where a careful choice of the interpulse timing is required. Shadowgraphic images of the plasma demonstrate that cavitation bubbles are formed early after the plasma onset and that the effect of hydrostatic pressure is negligible during the early stage of plasma expansion. Contrarily to what is observed at atmospheric pressure, emission spectra observed at high pressures are characterized by self-absorbed atomic lines on continuum radiation resulting from strong radiative recombination in the electron-rich confined environment. This effect is much less evident with ionic lines due to the much higher energy of the levels involved and ionization energy of ions, as well as to the lower extent of absorption effects occurring in the inner part of the plasma, where ionized species are more abundant. As a result of the smaller shorter-lived cavitation bubble, the LIBS intensity enhancement resulting from dual pulse excitation is reduced when the applied pressure increases.

Mean charge states of MeV/u Fe, Co, Ni and Cu ions in Au and Bi solid targets

International Nuclear Information System (INIS)

Ciortea, C.; Dumitriu, D.E.; Enescu, S.E.; Enulescu, A.; Fluerasu, D.; Piticu, I.; Szilagyi, Z.S.

2001-01-01

The average charge states of 0.1 - 1.5 MeV/u Fe, Co, Ni, and Cu ions in solid Au and Bi targets have been determined by estimating the mean numbers of outer-shell spectator vacancies during the K-vacancy decay. The latter quantities were obtained from the yield and energy shifts of the K α , β X-rays, by comparing with calculations in the independent electron approximation. The reported equilibrium charges, mostly characteristic for the inside of the target, are in fairly agreement with Nikolaev and Dmitriev semi-empirical formula. (authors)

Solid state solvation effect and reduced amplified spontaneous emission threshold value of glass forming DCM derivative in PMMA films

Energy Technology Data Exchange (ETDEWEB)

Vembris, Aivars, E-mail: aivars.vembris@cfi.lu.lv [Institute of Solid State Physics, University of Latvia, 8 Kengaraga Street, Riga LV 1063 (Latvia); Zarins, Elmars; Kokars, Valdis [Institute of Applied Chemistry, Riga Technical University, 14/24 Azenes Street, Riga LV 1048 (Latvia)

2015-02-15

Molecule crystallization is one of the limitations for obtaining high-gain organic laser systems. One of the examples is well known red laser dye 4-(dicyanomethylene)-2-methyl-6-(p-dimethylaminostyryl)-4H-pyran (DCM). The lowest threshold value of amplified spontaneous emission was achieved by doping 2 wt% of DCM molecule in tris-(8-hydroxy quinoline) aluminum (Alq{sub 3}) matrix. Further increase of the DCM dye concentration makes the system less efficient as its threshold value increases. It is due to large intermolecular interaction, which induces photoluminescence quenching. Compounds with reduced intermolecular interaction could be prospective in organic laser systems due to higher possible doping. In this work photoluminescence and amplified spontaneous emission properties of modified DCM molecule in poly(methyl methacrylate) (PMMA) matrix were investigated. Bulky trityloxyethyl groups were attached to the donor part of DCM. These groups increase intermolecular distance wherewith reduce photoluminescence quenching. More than one order of magnitude lower excitation threshold energy of the amplified spontaneous emission was achieved in doped polymer films with investigated compound in comparison to doped polymer with DCM. It means that the investigated compound is more perspective as a laser material compared to the previously studied. In addition, amplified spontaneous emission maximum could be tuned within 15 nm by changing concentration from 0.1 wt% to 10 wt% DWK-1 in PMMA matrix due to solid state solvation effect. - Highlights: • Bulky groups attached to DCM dye reduce photoluminescence quenching. • Amplified spontaneous emission is in red spectral region. • Amplified spontaneous emission spectra were tuned by 15 nm. • Amplified spontaneous emission threshold value was reduced by one order of magnitude.

MRI after magnetic drug targeting in patients with advanced solid malignant tumors

International Nuclear Information System (INIS)

Lemke, A.-J.; Senfft von Pilsach, M.-I.; Felix, R.; Luebbe, A.; Bergemann, C.; Riess, H.

2004-01-01

The purpose of this study was to evaluate the ability of MRI to detect magnetic particle uptake into advanced solid malignant tumors and to document the extension of these tumors, carried out in the context of magnetic drug targeting. In a prospective phase I trial, 11 patients were examined with MRI before and after magnetic drug targeting. The sequence protocol included T1-WI and T2-WI in several planes, followed by quantitative and qualitative evaluation of the signal intensities and tumor extensions. In nine patients, a signal decrease was observed in the early follow-up (2-7 days after therapy) on the T2-weighted images; two patients did not show a signal change. The signal changes in T1-WI were less distinct. In late follow-up (4-6 weeks after therapy), signal within nine tumors reached their initially normal level on both T1-WI and T2-WI; two tumors showed a slight signal decrease on T2-WI and a slight signal increase on T1-WI. Within the surveillance period, tumor remission in 3 out of 11 patients was observed, and in 5 patients tumor growth had stopped. The remaining three patients showed significant tumor growth. There was no statistically significant correlation between signal change and response. MRI is a suitable method to detect magnetite particles, deposited at the tumor site via magnetic drug targeting. MRI is therefore eligible to control the success of MDT and to assess the tumor size after the end of therapy. (orig.)

Nitrous Oxide Emissions after Application of Manure-Derived Fertiliseres

DEFF Research Database (Denmark)

Zhu, Kun

of N2O emission between different manure-derived fertilisers were observed. The application of fresh or composted manure solids had much higher N2O emissions than that of charred manure solids which contained low available C and N contents. The immature compost with a high content of dissolved organic...... different levels of C availability. The turnover and availability of N was modified by addition of nitrification inhibitor dicyandiamide (DCD) or mineral N. Soil O2 dynamics was monitored with high spatiotemporal resolution to elucidate the related mechanism regulating N2O emissions. Significant differences...... warming. This PhD project therefore investigated N2O emissions from soil after application of manure-derived fertilisers with varying spatial distribution, and evaluated the influences of available C, N and O2 on N2O emissions. Fresh, composted and charred manure solids were applied in soil to provide...

The critical role of the industrial sector in reaching long-term emission reduction, energy efficiency and renewable targets

International Nuclear Information System (INIS)

Fais, Birgit; Sabio, Nagore; Strachan, Neil

2016-01-01

Highlights: • A new industrial modelling approach in a whole energy systems model is developed. • The contribution of UK industry to long-term energy policy targets is analysed. • Emission reductions of up to 77% can be achieved in the UK industry until 2050. • The UK industry sector is essential for achieving the overall efficiency commitments. • UK industry can make a moderate contribution to the expansion of renewable energies. - Abstract: This paper evaluates the critical contribution of the industry sector to long-term decarbonisation, efficiency and renewable energy policy targets. Its methodological novelty is the incorporation of a process-oriented modelling approach based on a comprehensive technology database for the industry sector in a national energy system model for the UK (UKTM), allowing quantification of the role of both decarbonisation of upstream energy vectors and of mitigation options in the industrial sub-categories. This enhanced model is then applied in a comparative policy scenario analysis that explores various target dimensions on emission mitigation, renewable energy and energy efficiency at both a national and European level. The results show that ambitious emission cuts in the industry sector of up to 77% until 2050 compared to 2010 can be achieved. Moreover, with a reduction in industrial energy demand of up to 31% between 2010 and 2050, the sector is essential for achieving the overall efficiency commitments. The industry sector also makes a moderate contribution to the expansion of renewable energies mostly through the use of biomass for low-temperature heating services. However, additional sub-targets on renewable sources and energy efficiency need to be assessed critically, as they can significantly distort the cost-efficiency of the long-term mitigation pathway.

X-ray tube target

International Nuclear Information System (INIS)

Weber, R.G.

1980-01-01

A target with an improved heat emissive surface for use in a rotating anode type x-ray tube is described. The target consists of a body having a first surface portion made of x-ray emissive material and a second surface portion made of a heat emissive material comprising at least one of hafnium boride, hafnium oxide, hafnium nitride, hafnium silicide, and hafnium aluminide. (U.K.)

Cyclotron production of radionuclides in aqueous target matrices as alternative to solid state targetry. Production of Y-86 as example

Energy Technology Data Exchange (ETDEWEB)

Vogg, A.T.J.; Lang, R.; Meier-Boeke, P.; Scheel, W.; Reske, S.N.; Neumaier, B. [Universitaetsklinikum Ulm (Germany). Abt. Nuklearmedizin

2004-07-01

Commonly used ''organic'' positron emitting radionuclides {sup 18}F, {sup 11}C, {sup 13}N, and {sup 15}O are simply obtained from gaseous or aqueous targets, which enable an automated handling of target, i.e. both, filling and radionuclide delivery to a hot cell containing a chemistry processing and/or labelling module. In the recent years other - mostly metallic - radionuclides for PET gained more and more interest, since they can be used as surrogates for therapeutic nuclides attached to biomolecules like peptides or antibodies. The implication for surrogate nuclides results from the circumstance that an optimum dosimetric regime in endo radiotherapy relies on quantitative pharmacokinetic data obtained only by non invasive in vivo PET scans. However, for production of these alternative positron emitters the vast majority of them affords solid targets in form of metal foils, oxide or salt pellets which can not be operated by an automated processing. Those solid target systems have to be mounted and dismounted after irradiation by man, leading to two major disadvantages. First, manual cyclotron intervention is practically unsuited for daily routine radionuclide production and second the operating staff receives high radiation doses from the activated target. An alternative could be the irradiation of aqueous salts of target isotopes, allowing automated target operation. The major requirements are firstly a thermal stability of the dissolved compound, secondly the avoidance of counter ions containing nuclides which produce long-lived radionuclides under irradiation and thirdly a high solubility of the salt in the aqueous matrix. Here we report the proof of principle of the new radionuclide production concept by irradiation of strontium nitrate dissolved in water in order to produce {sup 86}Y (cf.). (orig.)

Optical and thermal energy discharge from tritiated solid hydrogen

International Nuclear Information System (INIS)

Magnotta, F.; Mapoles, E.R.; Collins, G.W.; Souers, P.C.

1991-01-01

The authors are investigating mechanisms of energy storage and release in tritiated solid hydrogens, by a variety of techniques including ESR, NMR and thermal and optical emission. The nuclear decay of a triton in solid hydrogen initiates the conversion of nuclear energy into stored chemical energy by producing unpaired hydrogen atoms which are trapped within the molecular lattice. The ability to store large quantities of atoms in this manner has been demonstrated and can serve as a basis for new forms of high energy density materials. This paper presents preliminary results of a study of the optical emission from solid hydrogen containing tritium over the visible and near infrared (NIR) spectral regions. Specifically, they have studied optical emission from DT and T 2 using CCD, silicon diode and germanium diode arrays. 8 refs., 6 figs

First meeting on the CRP 'standardized high current solid targets for cyclotron production of diagnostic and therapeutic radionuclides'

International Nuclear Information System (INIS)

Winkel, P. van den

2000-01-01

The Cyclotron Department of the VUB has three groups performing research in the field of target development, production of radionuclides and their application in nuclear medicine. 1. The Physics Group is busy on the optimization of beam parameters, on the determination of cross sections and on neutron spectrometry. 2. The Inorganic Radiochemistry Group performs research on solid target electroplating (Tl, Zn, Cd, Rh ... ), on optimisation of target carrier geometry and cooling and on automated PC-controlled radiochemistry (Tl-201, Ga-67, In-111) and recovery systems and the associated software written in Modula-2 and Visual Basic. 3. The Organic Radiochemistry Group develops new techniques for radiolabelling of organic molecules (fatty acids, neuroleptics, synthetic polypeptides...) useful in diagnostic and therapeutic nuclear medicine. All three groups take part in bulk productions of radionuclides

Electronic emission produced by light projectiles at intermediate energies

International Nuclear Information System (INIS)

Bernardi, G.C.

1989-01-01

Two aspects of the electronic emission produced by light projectiles of intermediate energies have been studied experimentally. In the first place, measurements of angular distributions in the range from θ = 0 deg -50 deg induced by collisions of 50-200 keV H + incident on He have been realized. It was found that the double differential cross section of electron emission presents a structure focussed in the forward direction and which extends up to relatively large angles. Secondly, the dependence of the double differential cross section on the projectile charge was studied using H + and He 3 2+ projectiles of 50 and 100 keV/amu incident on He. Strong deviations from a constant scaling factor were found for increasing projectile charge. The double differential cross sections and the single differential cross sections as a function of the emission angle, and the ratios of the emissions induced by He 3 2+ and H + at equal incident projectile velocities are compared with the 'Continuum Distorted Wave-Eikonal Initial State' (CDW-EIS) approximation and the 'Classical Trajectory Monte Carlo' (CTMC) method. Both approximations, in which the potential of the projectile exercises a relevant role, reproduce the general aspects of the experimental results. An electron analyzer and the corresponding projectile beam line has been designed and installed; it is characterized by a series of properties which are particularly appropriate for the study of double differential electronic emission in gaseous as well as solid targets. The design permits to assure the conditions to obtain a well localized gaseous target and avoid instrumental distortions of the measured distributions. (Author) [es

Buparvaquone loaded solid lipid nanoparticles for targeted delivery in theleriosis

Science.gov (United States)

Soni, Maheshkumar P.; Shelkar, Nilakash; Gaikwad, Rajiv V.; Vanage, Geeta R.; Samad, Abdul; Devarajan, Padma V.

2014-01-01

Background: Buparvaquone (BPQ), a hydroxynaphthoquinone derivative, has been investigated for the treatment of many infections and is recommended as the gold standard for the treatment of theileriosis. Theileriosis, an intramacrophage infection is localized mainly in reticuloendotheileial system (RES) organs. The present study investigates development of solid lipid nanoparticles (SLN) of BPQ for targeted delivery to the RES. Materials and Methods: BPQ SLN was prepared using melt method by adding a molten mixture into aqueous Lutrol F68 solution (80°C). Larger batches were prepared up to 6 g of BPQ with GMS: BPQ, 2:1. SLN of designed size were obtained using ultraturrax and high pressure homogenizer. A freeze and thaw study was used to optimize type and concentration of cryoprotectant with Sf: Mean particle size, Si: Initial particle size Solutol HS-15 and Lutrol F68 at 2% w/v and greater enabled the desired Sf/Si < 1.3. Differential scanning calorimetry and powder X-ray diffraction revealed decrease in crystallinity of BPQ in BPQ SLN while, scanning electron microscope revealed spherical morphology. BPQ SLN revealed good stability at 4°C and 25°C. Low hemolytic potential (<8%) and in vitro serum stability up to 5 h was observed. Cytotoxicity of SLN to the U937 cell was low. The macrophage cell line revealed high (52%) uptake of BPQ SLN in 1 h suggesting the potential to RES uptake. SLN revealed longer circulation and biodistrbution study confirmed high RES uptake (75%) in RES organs like liver lung spleen etc. Conclusion: The high RES uptake suggests BPQ SLN as a promising approach for targeted and improved delivery in theileriosis. PMID:24459400

Development of cyclotron solid targetry

International Nuclear Information System (INIS)

D'Souza, J.; Deans, T.; Cryer, D.; Price, R.

2004-01-01

bunker. Electrometers were attached to measure beam current obtained on the target and on the beam line. This was to ensure that the ratio of current hitting the target position is optimised compared to the current hitting the beam line. Teflon (mp: 285-295 deg C) was used in order to electrically isolate the target from the beam line. The cyclotron roughing pump was used to pull the beam line down to 10 -3 bar. The isolation valve between the beam line and the cyclotron was opened. The cyclotron was run for 10 minutes at a low current During the first trial of the beam line two main problems arose: 1. Although the beam line was brought down to 10 3 bar prior to the isolation valve being opened, the large volume within the beam line (compared with that in the regularly used liquid targets) contained enough air to cause flow into the cyclotron, sufficient to rupture the strippers. 2. The bombardment melted the Teflon insulator. Due to these faults the design of the beam line was changed. A diffusion pump was fitted to the beam line which evacuated the beam line to 10 -7 bar. The beam line was fitted onto the cyclotron and the port isolation valve opened. There was no loss of stripper integrity. This design improvement of including the diffusion pump on the beam line was therefore successful. The target body was electrically isolated from the beam line further away from the target and also incorporated water cooling via a water flow system, therefore the temperature of this component will not reach its melting point. The next step is to bombard the target to verify that the new cooling system is successful. Once this bombardment has been conducted successfully, the next step in the project is to irradiate a disc of known substance and get a profile of the beam at the target position by measuring the emissions from the disc using radiographic film. Considerable progress has been achieved in the design of a facility for bombarding solid targets, using the medical cyclotron

Target imaging and backlighting diagnosis

International Nuclear Information System (INIS)

Yaakobi, B.; Shvarts, D.; Marshall, F.J.; Epstein, R.; Su, Q.

1995-01-01

The expected backlighting and self-emission images of a particular CH target to be imploded on the Omega Upgrade are calculated for a variety of experimental parameters. It is shown that to overcome the problem of target self-emission, the image has to be monochromatized with a diffracting crystal. For the target studied, the two image components are then comparable in intensity and both provide useful information on target behavior. A particularly interesting feature is the appearance in the self-emission of a circular spike which closely delineates the fuel-shell interface, but requires high spatial resolution to be observed

Emissions from small-scale burns of simulated deployed U.S. military waste.

Science.gov (United States)

Woodall, Brian D; Yamamoto, Dirk P; Gullett, Brian K; Touati, Abderrahmane

2012-10-16

U.S. military forces have historically relied on open burning as an expedient method of volume reduction and treatment of solid waste during the conflicts in Afghanistan and Iraq. This study is the first effort to characterize a broad range of pollutants and their emission factors during the burning of military waste and the effects that recycling efforts, namely removing plastics, might have on emissions. Piles of simulated military waste were constructed, burned, and emissions sampled at the U.S. Environmental Protection Agency (EPA) Open Burn Testing Facility (OBTF), Research Triangle Park, NC. Three tests contained polyethylene terephthalate (PET #1 or PET) plastic water bottles and four did not. Emission factors for polycyclic aromatic hydrocarbons (PAHs), volatile organic compounds (VOCs), particulate matter (PM(10), PM(2.5)), polychlorinated and polybrominated dioxins/furans (PCDD/F and PBDD/F), and criteria pollutants were determined and are contained within. The average PCDD/F emission factors were 270 ng-toxic equivalency (TEQ) per kg carbon burned (ng-TEQ/kg Cb), ranging from 35 to 780 ng-TEQ/kg Cb. Limited testing suggests that targeted removal of plastic water bottles has no apparent effect on reducing pollutants and may even promote increased emissions.

Switching transport modes to meet voluntary carbon emission targets

NARCIS (Netherlands)

Hoen, K.M.R.; Tan, T.; Fransoo, J.C.; Houtum, van G.J.J.A.N.

2014-01-01

The transport sector is the second largest carbon emissions contributor in Europe and its emissions continue to increase. Many producers are committing themselves to reducing transport emissions voluntarily, possibly in anticipation of increasing transport prices. In this paper we study a producer

Switching transport modes to meet voluntary carbon emission targets

NARCIS (Netherlands)

Hoen, K.M.R.; Tan, T.; Fransoo, J.C.; Houtum, van G.J.J.A.N.

2011-01-01

The transport sector is the second largest carbon emissions contributor in Europe and its emissions continue to increase. Many shippers are committing themselves to reducing transport emissions voluntarily, possibly in anticipation of increasing transport prices. In this paper we study a shipper

Impact of economic growth, nonrenewable and renewable energy consumption, and urbanization on carbon emissions in Sub-Saharan Africa.

Science.gov (United States)

Hanif, Imran

2018-05-01

The present study explores the impact of economic growth; urban expansion; and consumption of fossil fuels, solid fuels, and renewable energy on environmental degradation in developing economies of Sub-Saharan Africa. To demonstrate its findings in detail, the study adopts a system generalized method of moment (GMM) on a panel of 34 emerging economies for the period from 1995 to 2015. The results describe that the consumption of fossil and solid fuels for cooking and expansion of urban areas are significantly contributing to carbon dioxide emissions, on one end, and stimulating air pollution, on the other. The results also exhibit an inverted U-shape relationship between per capita economic growth and carbon emissions. This relation confirms the existence of an environmental Kuznets curve (EKC) in middle- and low-income economies of Sub-Saharan Africa. Furthermore, the findings reveal that the use of renewable energy alternatives improves air quality by controlling carbon emissions and lowering the direct interaction of households with toxic gases. Thus, the use of renewable energy alternatives helps the economies to achieve sustainable development targets.

Experimental results on 2-30 keV bremsstrahlung from thick and thin targets

Energy Technology Data Exchange (ETDEWEB)

Shanker, R. [Atomic Physics Laboratory, Physics Department, Banaras Hindu University, Varanasi 221005 (India)]. E-mail: rshanker@bhu.ac.in

2006-10-15

The recent experimental investigations on electron bremsstrahlung produced from impact of 2-30 keV electrons with thick solid and thin gaseous targets are reviewed. The theoretical models describing the energy and angular distributions of bremsstrahlung photons are discussed with their brief outlines and formulations to explain the experimental data. The results on thick target bremsstrahlung (TTB) spectra produced by keV electrons have suggested that there is a need to develop a comprehensive theory for accounting the solid state effects. It is further noted that the prediction of the modified KKD formula gives a reasonable agreement with the TTB data, whereas a semi-empirical formula gives a better fit to the data for thick targets. The available experimental data for dependence of double differential cross-sections of emitted photons on impact energy and their emission angles for gaseous atoms and molecules exhibit a good agreement with the theoretical calculations of Kissel et al., [1983. Shape functions for atomic-field bremsstrahlung from electrons of kinetic energy 1-500 keV on selected neutral atoms 1

Impacts of residential heating intervention measures on air quality and progress towards targets in Christchurch and Timaru, New Zealand

Science.gov (United States)

Scott, Angelique J.; Scarrott, Carl

2011-06-01

Elevated wintertime particulate concentrations in the New Zealand cities of Christchurch and Timaru are mostly attributed to the burning of wood and coal for residential heating. A carrot-and-stick approach was adopted for managing air quality in Christchurch, where strict intervention measures were introduced together with a residential heater replacement programme to encourage householders to change to cleaner forms of heating. A similar approach was only recently implemented for Timaru. This paper presents the results of a partial accountability analysis, where the impact of these measures on the target source, PM 10 emissions, and PM 10 concentrations are quantified. A statistical model was developed to estimate trends in the concentrations, which were tested for significance after accounting for meteorological effects, and to estimate the probability of meeting air quality targets. Results for Christchurch and Timaru are compared to illustrate the impacts of differing levels of intervention on air quality. In Christchurch, approximately 34,000 (76%) open fires and old solid fuel burners were replaced with cleaner heating technology from 2002 to 2009, and total open fires and solid fuel burner numbers decreased by 45%. Over the same time period, estimated PM 10 emissions reduced by 71% and PM 10 concentrations by 52% (maxima), 36% (winter mean), 26% (winter median) and 41% (meteorology-adjusted winter means). In Timaru, just 3000 (50%) open fires and old solid fuel burners were replaced from 2001 to 2008, with total open fire and solid fuel burner numbers reduced by 24%. PM 10 emissions declined by 32%, with low reductions in the PM 10 concentrations (maxima decreased by 7%, winter means by 11% and winter medians by 3%). These findings, supported by the results of the meteorology corrected trend analysis for Christchurch, strongly indicate that the combination of stringent intervention measures and financial incentives has led to substantial air quality

Delay-induced rebounds in CO2 emissions and critical time-scales to meet global warming targets

Science.gov (United States)

Manoli, Gabriele; Katul, Gabriel G.; Marani, Marco

2016-12-01

While climate science debates are focused on the attainment of peak anthropogenic CO2 emissions and policy tools to reduce peak temperatures, the human-energy-climate system can hold "rebound" surprises beyond this peak. Following the second industrial revolution, global per capita CO2 emissions (cc) experienced a punctuated growth of about 100% every 60 years, mainly attributable to technological development and its global spread. A model of the human-energy-climate system capable of reproducing past punctuated dynamics shows that rebounds in global CO2 emissions emerge due to delays intrinsic to the diffusion of innovations. Such intrinsic delays in the adoption and spread of low-carbon emitting technologies, together with projected population growth, upset the warming target set by the Paris Agreement. To avoid rebounds and their negative climate effects, model calculations show that the diffusion of climate-friendly technologies must occur with lags one-order of magnitude shorter (i.e., ˜6 years) than the characteristic timescale of past punctuated growth in cc. Radically new strategies to globally implement the technological advances at unprecedented rates are needed if the current emission goals are to be achieved.

Electron transport in solid targets and in the active mixture of a CO2 laser amplifier

Science.gov (United States)

Galkowski, A.

The paper examines the use of the NIKE code for the Monte Carlo computation of the deposited energy profile and other characteristics of the absorption process of an electron beam in a solid target and the spatial distribution of primary ionization in the active mixture of a CO2 laser amplifier. The problem is considered in connection with the generation of intense electron beams and the acceleration of thin metal foils, as well as in connection with the electric discharge pumping of a CO2 laser amplifier.

The effectiveness of Light Rail transit in achieving regional CO2 emissions targets is linked to building energy use: insights from system dynamics modeling

Science.gov (United States)

Cities worldwide face the challenges of accommodating a growing population, while reducing emissions to meet climate mitigation targets. Public transit investments are often proposed as a way to curb emissions while maintaining healthy urban economies. However, cities face a syst...

A Novel Detection Method for Underwater Moving Targets by Measuring Their ELF Emissions with Inductive Sensors

Directory of Open Access Journals (Sweden)

Jinhong Wang

2017-07-01

Full Text Available In this article, we propose a novel detection method for underwater moving targets by detecting their extremely low frequency (ELF emissions with inductive sensors. The ELF field source of the targets is modeled by a horizontal electric dipole at distances more than several times of the targets’ length. The formulas for the fields produced in air are derived with a three-layer model (air, seawater and seafloor and are evaluated with a complementary numerical integration technique. A proof of concept measurement is presented. The ELF emissions from a surface ship were detected by inductive electronic and magnetic sensors as the ship was leaving a harbor. ELF signals are of substantial strength and have typical characteristic of harmonic line spectrum, and the fundamental frequency has a direct relationship with the ship’s speed. Due to the high sensitivity and low noise level of our sensors, it is capable of resolving weak ELF signals at long distance. In our experiment, a detection distance of 1300 m from the surface ship above the sea surface was realized, which shows that this method would be an appealing complement to the usual acoustic detection and magnetic anomaly detection capability.

Handbook of Applied Solid State Spectroscopy

CERN Document Server

Vij, D. R

2006-01-01

Solid-State spectroscopy is a burgeoning field with applications in many branches of science, including physics, chemistry, biosciences, surface science, and materials science. Handbook of Applied Solid-State Spectroscopy brings together in one volume information about various spectroscopic techniques that is currently scattered in the literature of these disciplines. This concise yet comprehensive volume covers theory and applications of a broad range of spectroscopies, including NMR, NQR, EPR/ESR, ENDOR, scanning tunneling, acoustic resonance, FTIR, auger electron emission, x-ray photoelectron emission, luminescence, and optical polarization, and more. Emphasis is placed on fundamentals and current methods and procedures, together with the latest applications and developments in the field.

Introduction to the physics of electron emission

CERN Document Server

Jensen, Kevin L

2018-01-01

Electron emission is both a fundamental phenomenon and an enabling component that lies at the very heart of modern science and technology. Written by a recognized authority in the field, with expertise in both electron emission physics and electron beam physics, An Introduction to Electron Emission provides an in-depth look at the physics behind thermal, field, photo, and secondary electron emission mechanisms, how that physics affects the beams that result through space charge and emittance growth, and explores the physics behind their utilization in an array of applications. The book addresses mathematical and numerical methods underlying electron emission, describing where the equations originated, how they are related, and how they may be correctly used to model actual sources for devices using electron beams. Writing for the beam physics and solid state communities, the author explores applications of electron emission methodology to solid state, statistical, and quantum mechanical ideas and concepts r...

Ultrafast streak and framing technique for the observation of laser driven shock waves in transparent solid targets

International Nuclear Information System (INIS)

Van Kessel, C.G.M.; Sachsenmaier, P.; Sigel, R.

1975-01-01

Shock waves driven by laser ablation in plane transparent plexiglass and solid hydrogen targets have been observed with streak and framing techniques using a high speed image converter camera, and a dye laser as a light source. The framing pictures have been made by mode locking the dye laser and using a wide streak slit. In both materials a growing hemispherical shock wave is observed with the maximum velocity at the onset of laser radiation. (author)

Simulation and Automation of Microwave Frequency Control in Dynamic Nuclear Polarization for Solid Polarized Targets

Science.gov (United States)

Perera, Gonaduwage; Johnson, Ian; Keller, Dustin

2017-09-01

Dynamic Nuclear Polarization (DNP) is used in most of the solid polarized target scattering experiments. Those target materials must be irradiated using microwaves at a frequency determined by the difference in the nuclear Larmor and electron paramagnetic resonance (EPR) frequencies. But the resonance frequency changes with time as a result of radiation damage. Hence the microwave frequency should be adjusted accordingly. Manually adjusting the frequency can be difficult, and improper adjustments negatively impact the polarization. In order to overcome these difficulties, two controllers were developed which automate the process of seeking and maintaining the optimal frequency: one being a standalone controller for a traditional DC motor and the other a LabVIEW VI for a stepper motor configuration. Further a Monte-Carlo simulation was developed which can accurately model the polarization over time as a function of microwave frequency. In this talk, analysis of the simulated data and recent improvements to the automated system will be presented. DOE.

Solid targetry for compact cyclotrons

International Nuclear Information System (INIS)

Comor, J.

2004-01-01

In this presentation authors present experimental results of solid targetry for compact cyclotrons. It is concluded: Solid targetry is not restricted to large accelerator centers anymore; Small and medium scale radioisotope production is feasible with compact cyclotrons; The availability of versatile solid target systems is expected to boost the radiochemistry of 'exotic' positron emitters

Solid-fuel cook stoves: Fuel efficiency and emissions testing--Austin

Science.gov (United States)

The World Health Organization estimates that approximately 1.6 million people prematurely die each year due to exposure to air pollutants from burning solid fuels for residential cooking and heating (WHO, 2010). Residential solid-fuel use accounts for approximately 25 percent of ...

Contribution of ICT to Climate Targets of Cities. Exploring the potential of Information and Communication Technologies in reducing emissions and energy use from buildings and travel

Energy Technology Data Exchange (ETDEWEB)

Kramers, Anna

2012-07-01

This thesis examines how ICT solutions can assist in lowering energy use and greenhouse gas (GHG) emissions from buildings and travel in order to help cities meet their climate targets. It also provides an overview of relevant research intended to furnish new knowledge about the issues involved and to find solutions to social problems. The first part of the thesis provides an analysis and compilation of critical system boundaries that need to be used for cities to set targets for energy use and GHG emissions. The climate targets of cities are dependent on setting system boundaries and establishing methods of calculations for monitoring whether the targets have been achieved. Today, there is no official standard for how the system boundaries must be set or what calculation methodologies to apply to evaluate the climate targets. Four main categories of system boundaries were identified: the temporal scope, the object of target setting, the unit of target setting, and the target range (e.g. consumer-producer and lifecycle perspective). Eight European cities were examined in relation to how they set climate targets. The examination showed that awareness of what is included in the targets is limited and that there is a need for standardised and consistent protocols and methods of setting climate targets for cities. In the second part of the thesis, leading Advanced Traveller Information Systems (ATIS) and their functionalities were investigated. The relationship between individual decisions on different travel modes and functionalities of ATIS was investigated through a systematic investigation of the functionality of nine ATIS, mainly from Sweden, Germany, UK and USA. This allowed decisions that could lead to lower energy use and emissions of GHG to be identified. It also resulted in a proposal on requirements for new and improved functionality that could support a reduction in energy use and GHG emissions and a shift to renewable energy sources if implemented in next

Lactoferrin bioconjugated solid lipid nanoparticles: a new drug delivery system for potential brain targeting.

Science.gov (United States)

Singh, Indu; Swami, Rajan; Pooja, Deep; Jeengar, Manish Kumar; Khan, Wahid; Sistla, Ramakrishna

2016-01-01

Delivery of drugs to brain is a subtle task in the therapy of many severe neurological disorders. Solid lipid nanoparticles (SLN) easily diffuse the blood-brain barrier (BBB) due to their lipophilic nature. Furthermore, ligand conjugation on SLN surface enhances the targeting efficiency. Lactoferin (Lf) conjugated SLN system is first time attempted for effective brain targeting in this study. Preparation of Lf-modified docetaxel (DTX)-loaded SLN for proficient delivery of DTX to brain. DTX-loaded SLN were prepared using emulsification and solvent evaporation method and conjugation of Lf on SLN surface (C-SLN) was attained through carbodiimide chemistry. These lipidic nanoparticles were evaluated by DLS, AFM, FTIR, XRD techniques and in vitro release studies. Colloidal stability study was performed in biologically simulated environment (normal saline and serum). These lipidic nanoparticles were further evaluated for its targeting mechanism for uptake in brain tumour cells and brain via receptor saturation studies and distribution studies in brain, respectively. Particle size of lipidic nanoparticles was found to be optimum. Surface morphology (zeta potential, AFM) and surface chemistry (FTIR) confirmed conjugation of Lf on SLN surface. Cytotoxicity studies revealed augmented apoptotic activity of C-SLN than SLN and DTX. Enhanced cytotoxicity was demonstrated by receptor saturation and uptake studies. Brain concentration of DTX was elevated significantly with C-SLN than marketed formulation. It is evident from the cytotoxicity, uptake that SLN has potential to deliver drug to brain than marketed formulation but conjugating Lf on SLN surface (C-SLN) further increased the targeting potential for brain tumour. Moreover, brain distribution studies corroborated the use of C-SLN as a viable vehicle to target drug to brain. Hence, C-SLN was demonstrated to be a promising DTX delivery system to brain as it possessed remarkable biocompatibility, stability and efficacy than

Formation of target-specific binding sites in enzymes: solid-phase molecular imprinting of HRP

Science.gov (United States)

Czulak, J.; Guerreiro, A.; Metran, K.; Canfarotta, F.; Goddard, A.; Cowan, R. H.; Trochimczuk, A. W.; Piletsky, S.

2016-05-01

Here we introduce a new concept for synthesising molecularly imprinted nanoparticles by using proteins as macro-functional monomers. For a proof-of-concept, a model enzyme (HRP) was cross-linked using glutaraldehyde in the presence of glass beads (solid-phase) bearing immobilized templates such as vancomycin and ampicillin. The cross-linking process links together proteins and protein chains, which in the presence of templates leads to the formation of permanent target-specific recognition sites without adverse effects on the enzymatic activity. Unlike complex protein engineering approaches commonly employed to generate affinity proteins, the method proposed can be used to produce protein-based ligands in a short time period using native protein molecules. These affinity materials are potentially useful tools especially for assays since they combine the catalytic properties of enzymes (for signaling) and molecular recognition properties of antibodies. We demonstrate this concept in an ELISA-format assay where HRP imprinted with vancomycin and ampicillin replaced traditional enzyme-antibody conjugates for selective detection of templates at micromolar concentrations. This approach can potentially provide a fast alternative to raising antibodies for targets that do not require high assay sensitivities; it can also find uses as a biochemical research tool, as a possible replacement for immunoperoxidase-conjugates.Here we introduce a new concept for synthesising molecularly imprinted nanoparticles by using proteins as macro-functional monomers. For a proof-of-concept, a model enzyme (HRP) was cross-linked using glutaraldehyde in the presence of glass beads (solid-phase) bearing immobilized templates such as vancomycin and ampicillin. The cross-linking process links together proteins and protein chains, which in the presence of templates leads to the formation of permanent target-specific recognition sites without adverse effects on the enzymatic activity. Unlike

Carbon emissions and an equitable emission reduction criterion

International Nuclear Information System (INIS)

Golomb, Dan

1999-01-01

In 1995 the world-wide carbon emissions reached 5.8 billion metric tonnes per year (GTC/y). The Kyoto protocol calls for a reduction of carbon emissions from the developed countries (Annex I countries) of 6-8% below 1990 levels on the average, and unspecified commitments for the less developed (non-Annex I) countries. It is doubtful that the Kyoto agreement will be ratified by some parliaments, especially the USA Congress. Furthermore, it is shown that if the non-Annex I countries will not curtail their carbon emissions drastically, the global emissions will soar to huge levels by the middle of the next century. An equitable emission criterion is proposed which may lead to a sustainable rate of growth of carbon emissions, and be acceptable to all countries of the world. The criterion links the rate of growth of carbon emissions to the rate of growth of the Gross Domestic Product (GDP). A target criterion is proposed R = 0.15 KgC/SGDP, which is the current average for western European countries and Japan. This allows for both the growth of the GDP and carbon emissions. However, to reach the target in a reasonable time, the countries for which R≤ 0.3 would be allowed a carbon emission growth rate of 1%./y, and countries for which R≥ 0.3, 0.75%/y. It is shown that by 2050 the world-wide carbon emissions would reach about 10 GTC/y, which is about 3 times less than the Kyoto agreement would allow. (Author)

International Experience with Key Program Elements of IndustrialEnergy Efficiency or Greenhouse Gas Emissions Reduction Target-SettingPrograms

Energy Technology Data Exchange (ETDEWEB)

Price, Lynn; Galitsky, Christina; Kramer, Klaas Jan

2008-02-02

Target-setting agreements, also known as voluntary ornegotiated agreements, have been used by a number of governments as amechanism for promoting energy efficiency within the industrial sector. Arecent survey of such target-setting agreement programs identified 23energy efficiency or GHG emissions reduction voluntary agreement programsin 18 countries. International best practice related to target-settingagreement programs calls for establishment of a coordinated set ofpolicies that provide strong economic incentives as well as technical andfinancial support to participating industries. The key program elementsof a target-setting program are the target-setting process,identification of energy-saving technologies and measures usingenergy-energy efficiency guidebooks and benchmarking as well as byconducting energy-efficiency audits, development of an energy-savingsaction plan, development and implementation of energy managementprotocols, development of incentives and supporting policies, monitoringprogress toward targets, and program evaluation. This report firstprovides a description of three key target-setting agreement programs andthen describes international experience with the key program elementsthat comprise such programs using information from the three keytarget-setting programs as well as from other international programsrelated to industrial energy efficiency or GHG emissionsreductions.

Neutron pre-emission at the fusion of 11 Li halo nuclei with Si targets

International Nuclear Information System (INIS)

Petrascu, M.; Isbasescu, A.; Petrascu, H.; Bordeanu, C.; David, I.; Lazar, I.; Mihai, I.; Vaman, G.; Tanihata, I.; Kobayashi, T.; Korsheninnikov, A.; Fukuda, S.; Kumagai, H.; Momota, S.; Ozawa, A.; Yoshida, K.; Nikolski, E.; Giurgiu, M.

1997-01-01

In this contribution, the first experiment on fusion of 11 Li halo nuclei with Si targets is reported. A novel effect consisting of a large neutron pre-emission probability in the fusion process was observed. The neutron halo nuclei are characterized by very large matter radii, small separation energy and small internal momentum of the valence neutrons. Until now, the halo nuclei were investigated mostly by elastic, inelastic scattering and breakup processes. It was recently predicted that due to the very large dimension of 11 Li, one may expect, that in a fusion experiment on a light target, the valence neutrons will not be absorbed together with the 9 Li core, but will be emitted in the early stage of the reaction process. The experiment aiming to check this expectation, performed at RIKEN-RIPS facility, is described. In the experimental arrangement, three main parts are present: the first part contains the detectors used for the control, identification and determination of the beam characteristics; the second part consists of a Multiple Sampling Ionisation Chamber (MUSIC), used for identification of the inclusive evaporation residue spectra produced in the detector-target; the third part consists of two wall neutron detectors, each made up of 15 plastic scintillators. This detector was used for the energy and position determination of the neutrons originating from the target. The projectile energy range was 11.2 - 15.2 AMeV, centered at 13 AMeV. The neutrons resulting from the reaction were measured by time-of-light technique. The position on the 'wall' of the detected neutrons could be also determined. The measured neutron spectra from 11 Li and 9 Li are shown. A marked different between the two spectra was found and it is explained by the contribution of a large amount of pre-emission (breakup) processes, in case of 11 Li projectiles. The position spectra point out the evaporation origin of the neutrons in case of 9 Li projectiles while for 11 Li only the

Framework for the analysis of the low-carbon scenario 2020 to achieve the national carbon Emissions reduction target: Focused on educational facilities

International Nuclear Information System (INIS)

Koo, Choongwan; Kim, Hyunjoong; Hong, Taehoon

2014-01-01

Since the increase in greenhouse gas emissions has increased the global warming potential, an international agreement on carbon emissions reduction target (CERT) has been formulated in Kyoto Protocol (1997). This study aimed to develop a framework for the analysis of the low-carbon scenario 2020 to achieve the national CERT. To verify the feasibility of the proposed framework, educational facilities were used for a case study. This study was conducted in six steps: (i) selection of the target school; (ii) establishment of the reference model for the target school; (iii) energy consumption pattern analysis by target school; (iv) establishment of the energy retrofit model for the target school; (v) economic and environmental assessment through the life cycle cost and life cycle CO 2 analysis; and (vi) establishment of the low-carbon scenario in 2020 to achieve the national CERT. This study can help facility managers or policymakers establish the optimal retrofit strategy within the limited budget from a short-term perspective and the low-carbon scenario 2020 to achieve the national CERT from the long-term perspective. The proposed framework could be also applied to any other building type or country in the global environment

Nanosecond Nd-YAG laser induced plasma emission characteristics in low pressure CO{sub 2} ambient gas for spectrochemical application on Mars

Energy Technology Data Exchange (ETDEWEB)

Lie, Zener Sukra; Kurniawan, Koo Hendrik, E-mail: kurnia18@cbn.net.id [Research Center of Maju Makmur Mandiri Foundation, 40/80 Srengseng Raya, Jakarta 11630 (Indonesia); Pardede, Marincan [Department of Electrical Engineering, University of Pelita Harapan, 1100 M.H. Thamrin Boulevard, Lippo Village, Tangerang 15811 (Indonesia); Tjia, May On [Research Center of Maju Makmur Mandiri Foundation, 40/80 Srengseng Raya, Jakarta 11630 (Indonesia); Physics of Magnetism and Photonics Group, Faculty of Mathematics and Natural Sciences, Bandung Institute of Technology, 10 Ganesha, Bandung 40132 (Indonesia); Kagawa, Kiichiro [Fukui Science Education Academy, Takagi Chuou 2 choume, Fukui 910-0804 (Japan); Research Center of Maju Makmur Mandiri Foundation, 40/80 Srengseng Raya, Jakarta 11630 (Indonesia)

2015-08-28

An experimental study is conducted on the possibility and viability of performing spectrochemical analysis of carbon and other elements in trace amount in Mars, in particular, the clean detection of C, which is indispensible for tracking the sign of life in Mars. For this study, a nanosecond Nd-YAG laser is employed to generate plasma emission from a pure copper target in CO{sub 2} ambient gas of reduced pressure simulating the atmospheric condition of Mars. It is shown that the same shock wave excitation mechanism also works this case while exhibiting remarkably long cooling stage. The highest Cu emission intensities induced by 4 mJ laser ablation energy is attained in 600 Pa CO{sub 2} ambient gas. Meanwhile the considerably weaker carbon emission from the CO{sub 2} gas appears relatively featureless over the entire range of pressure variation, posing a serious problem for sensitive trace analysis of C contained in a solid sample. Our time resolved intensity measurement nevertheless reveals earlier appearance of C emission from the CO{sub 2} gas with a limited duration from 50 ns to 400 ns after the laser irradiation, well before the initial appearance of the long lasting C emission from the solid target at about 1 μs, due to the different C-releasing processes from their different host materials. The unwanted C emission from the ambient gas can thus be eliminated from the detected spectrum by a proper time gated detection window. The excellent spectra of carbon, aluminum, calcium, sodium, hydrogen, and oxygen obtained from an agate sample are presented to further demonstrate and verify merit of this special time gated LIBS using CO{sub 2} ambient gas and suggesting its viability for broad ranging in-situ applications in Mars.

Differential exposure and acute health impacts of inhaled solid-fuel emissions from rudimentary and advanced cookstoves in female CD-1 mice.

Science.gov (United States)

Gibbs-Flournoy, Eugene A; Gilmour, M Ian; Higuchi, Mark; Jetter, James; George, Ingrid; Copeland, Lisa; Harrison, Randy; Moser, Virginia C; Dye, Janice A

2018-02-01

There is an urgent need to provide access to cleaner end user energy technologies for the nearly 40% of the world's population who currently depend on rudimentary cooking and heating systems. Advanced cookstoves (CS) are designed to cut emissions and solid-fuel consumption, thus reducing adverse human health and environmental impacts. We hypothesized that, compared to a traditional (Tier 0) three-stone (3-S) fire, acute inhalation of solid-fuel emissions from advanced natural-draft (ND; Tier 2) or forced-draft (FD; Tier 3) stoves would reduce exposure biomarkers and lessen pulmonary and innate immune system health effects in exposed mice. Across two simulated cooking cycles (duration ~ 3h), emitted particulate mass concentrations were reduced 80% and 62% by FD and ND stoves, respectively, compared to the 3-S fire; with corresponding decreases in particles visible within murine alveolar macrophages. Emitted carbon monoxide was reduced ~ 90% and ~ 60%, respectively. Only 3-S-fire-exposed mice had increased carboxyhemoglobin levels. Emitted volatile organic compounds were FD ≪ 3-S-fire ≤ ND stove; increased expression of genes involved in xenobiotic metabolism (COX-2, NQO1, CYP1a1) was detected only in ND- and 3-S-fire-exposed mice. Diminished macrophage phagocytosis was observed in the ND group. Lung glutathione was significantly depleted across all CS groups, however the FD group had the most severe, ongoing oxidative stress. These results are consistent with reports associating exposure to solid fuel stove emissions with modulation of the innate immune system and increased susceptibility to infection. Lower respiratory infections continue to be a leading cause of death in low-income economies. Notably, 3-S-fire-exposed mice were the only group to develop acute lung injury, possibly because they inhaled the highest concentrations of hazardous air toxicants (e.g., 1,3-butadiene, toluene, benzene, acrolein) in association with the greatest number of particles, and

DFT study of electron absorption and emission spectra of pyramidal LnPc(OAc) complexes of some lanthanide ions in the solid state

Science.gov (United States)

Hanuza, J.; Godlewska, P.; Lisiecki, R.; Ryba-Romanowski, W.; Kadłubański, P.; Lorenc, J.; Łukowiak, A.; Macalik, L.; Gerasymchuk, Yu.; Legendziewicz, J.

2018-05-01

The electron absorption and emission spectra were measured for the pyramidal LnPc(OAc) complexes in the solid state and co-doped in silica glass, where Ln = Er, Eu and Ho. The theoretical electron spectra were determined from the quantum chemical DFT calculation using four approximations CAM-B3LYP/LANL2DZ, CAM-B3LYP/CC-PVDZ, B3LYP/LANL2DZ and B3LYP/CC-PVDZ. It was shown that the best agreement between the calculated and experimental structural parameters and spectroscopic data was reached for the CAM-B3LYP/LANL2DZ model. The emission spectra were measured using the excitations both in the ligand and lanthanide absorption ranges. The possibility of energy transfer between the phthalocyanine ligand and excited states of lanthanide ions was discussed. It was shown that the back energy transfer from metal states to phthalocyanine state is responsible for the observed emission of the studied complexes both in the polycrystalline state and silica glass.

Path towards achieving of China's 2020 carbon emission reduction target-A discussion of low-carbon energy policies at province level

International Nuclear Information System (INIS)

Wang Run; Liu Wenjuan; Xiao Lishan; Liu Jian; Kao, William

2011-01-01

Following the announcement of the China's 2020 national target for the reduction of the intensity of carbon dioxide emissions per unit of GDP by 40-45% compared with 2005 levels, Chinese provincial governments prepared to restructure provincial energy policy and plan their contribution to realizing the State reduction target. Focusing on Fujian and Anhui provinces as case studies, this paper reviews two contrasting policies as a means for meeting the national reduction target. That of the coastal province of Fujian proposes to do so largely through the development of nuclear power, whilst the coal-rich province of Anhui proposes to do so through its energy consumption rate rising at a lower rate than that of the rise in GDP. In both cases renewable energy makes up a small proportion of their proposed 2020 energy structures. The conclusion discusses in depth concerns about nuclear power policy, energy efficiency, energy consumption strategy and problems in developing renewable energy. - Research Highlights: → We review two contrasting policies as a means for meeting the national reduction target of carbon emission in two provinces. → Scenario review of energy structure in Fujian and Anhui Provinces to 2020. → We discuss concerns about nuclear power policy, energy efficiency, energy consumption strategy and problems in developing renewable energy.

Experimental and theoretical study of heavy ion slowing down in solid targets

International Nuclear Information System (INIS)

Mehana, A.

1993-06-01

Heavy ion energy losses in C, Al, Cu, Ag, Ta and Au solid targets have been measured at high energy (0.2 to 5 MeV/u), using the backward secondary ion technique, and at low energy (0.1 to 0.25 MeV/u) for the C, N and O ions, using the particle backscatter method. A brief review of the various matter-induced charged particle slowing down theories, and especially the Lindhard dielectric theory, is first presented. Then, the various models for the evaluation of the effective charge and of the high order correction, are discussed and compared. Experimental techniques and data processing methods are described, and the experimental results are compared to calculations derived from the dielectric theory. In particular, the effective charges and the high order corrections (Barkas-Bloch) are examined and compared to the models for the determination of the z 3 and z 4 terms for heavy ions

High-contrast laser acceleration of relativistic electrons in solid cone-wire targets

Energy Technology Data Exchange (ETDEWEB)

Higginson, D. P. [Univ. of California-San Diego, La Jolla, CA (United States); Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Link, A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Sawada, H. [Univ. of California-San Diego, La Jolla, CA (United States); Wilks, S. C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Chawla, S. R. [Univ. of California-San Diego, La Jolla, CA (United States); Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Chen, C. D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Jarrott, L. C. [Univ. of California-San Diego, La Jolla, CA (United States); Flippo, K. A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); McLean, H. S. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Patel, P. K. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Perez, F. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Beg, F. N. [Univ. of California-San Diego, La Jolla, CA (United States); Bartal, T. [Univ. of California-San Diego, La Jolla, CA (United States); Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Wei, M. S. [General Atomics, San Diego, CA (United States)

2015-12-31

Optimization of electron coupling into small solid angles is of extreme importance to applications, such as Fast Ignition, that require maximum electron energy deposition within a small volume. To optimize this coupling, we use the ultra-high-contrast Trident laser, which remains below intensity of 10¹¹ W/cm² until < 0.1 ns before the main pulse, while still attaining high-energy, 75 J, and peak intensity of 5 x 10¹⁹ W/cm². Using a cone-wire target, we find that the coupling into the 40 μm diameter wire is increased by a factor of 2.7x over the low-contrast Titan laser at similar peak intensity. Full-scale simulations are used to model the laser interaction and quantitatively reproduce the experimental results. These show that increase in coupling is due to both a closer interaction, as well as the reduction of laser filamentation and self-focusing.

MANAGEMENT OF SOLID WASTE GENERATED BY THE INTEGRATED STEELWORKS ACTIVITY AND SOLUTIONS TO REDUCE THE ENVIRONMENTAL IMPACT

Directory of Open Access Journals (Sweden)

Anişoara CIOCAN

2010-05-01

Full Text Available The development of steel industry is subject to solve major problems arising from industry-nature relationship, strictly targeted on pollution control and protection of natural resources and energy. In this paper we discussed about the management of solid waste generated by an integrated steelwork located near a major urban area and the adopted solutions for the reduction of environmental impact. There are summarized technical solutions that are currently applied and were proposed some solutions that can be applied in accordance with the environmental legislations. The new solutions are proposed for integrated management of solid wastes in accordance with: the exact quantification (quantitative, qualitative and the generation sources of emissions and solid wastes; controlled storage; minimization of the wastes and its harmfulness; transformation of the wastes into valuable by-products used directly by the company in a subsequent process, or by external down-stream user.

Pomace waste management scenarios in Quebec-Impact on greenhouse gas emissions

International Nuclear Information System (INIS)

Gassara, Fatma; Brar, S.K.; Pelletier, F.; Verma, M.; Godbout, S.; Tyagi, R.D.

2011-01-01

Highlights: → Incineration, landfill, animal feed, enzyme production by fermentation and, composting as apple pomace management strategies. → Reduction of GHG emissions using solid state fermentation of apple pomace → Highest GHG emissions during landfill. - Abstract: Fruit processing industries generate tremendous amount of solid wastes which is almost 35-40% dry weight of the total produce used for the manufacturing of juices. These solid wastes, referred to as, 'pomace' contain high moisture content (70-75%) and biodegradable organic load (high BOD and COD values) so that their management is an important issue. During the management of these pomace wastes by different strategies comprising incineration, landfill, composting, solid-state fermentation to produce high-value enzymes and animal feed, there is production of greenhouse gases (GHG) which must be taken into account. In this perspective, this study is unique that discusses the GHG emission analysis of agro-industrial waste management strategies, especially apple pomace waste management and repercussions of value-addition of these wastes in terms of their sustainability using life cycle assessment (LCA) model. The results of the analysis indicated that, among all the apple pomace management sub-models for a functional unit, solid-state fermentation to produce enzymes was the most effective method for reducing GHG emissions (906.81 tons CO 2 eq. per year), while apple pomace landfill resulted in higher GHG emissions (1841.00 tons CO 2 eq. per year). The assessment and inventory of GHG emissions during solid-state fermentation gave positive indications of environmental sustainability for the use of this strategy to manage apple pomace and other agricultural wastes, particularly in Quebec and also extended to other countries. The analysis and use of parameters in this study were drawn from various analytical approaches and data sources. There was absence of some data in the literature which led to

Pomace waste management scenarios in Quebec-Impact on greenhouse gas emissions

Energy Technology Data Exchange (ETDEWEB)

Gassara, Fatma [INRS-ETE, Universite du Quebec, 490, Rue de la Couronne, Quebec, Canada G1K 9A9 (Canada); Brar, S.K., E-mail: satinder.brar@ete.inrs.ca [INRS-ETE, Universite du Quebec, 490, Rue de la Couronne, Quebec, Canada G1K 9A9 (Canada); Pelletier, F.; Verma, M.; Godbout, S. [Institut de recherche et de developpement en agroenvironnement inc. (IRDA), 2700 rue Einstein, Quebec (Quebec), Canada G1P 3W8 (Canada); Tyagi, R.D. [INRS-ETE, Universite du Quebec, 490, Rue de la Couronne, Quebec, Canada G1K 9A9 (Canada)

2011-09-15

Highlights: {yields} Incineration, landfill, animal feed, enzyme production by fermentation and, composting as apple pomace management strategies. {yields} Reduction of GHG emissions using solid state fermentation of apple pomace {yields} Highest GHG emissions during landfill. - Abstract: Fruit processing industries generate tremendous amount of solid wastes which is almost 35-40% dry weight of the total produce used for the manufacturing of juices. These solid wastes, referred to as, 'pomace' contain high moisture content (70-75%) and biodegradable organic load (high BOD and COD values) so that their management is an important issue. During the management of these pomace wastes by different strategies comprising incineration, landfill, composting, solid-state fermentation to produce high-value enzymes and animal feed, there is production of greenhouse gases (GHG) which must be taken into account. In this perspective, this study is unique that discusses the GHG emission analysis of agro-industrial waste management strategies, especially apple pomace waste management and repercussions of value-addition of these wastes in terms of their sustainability using life cycle assessment (LCA) model. The results of the analysis indicated that, among all the apple pomace management sub-models for a functional unit, solid-state fermentation to produce enzymes was the most effective method for reducing GHG emissions (906.81 tons CO{sub 2} eq. per year), while apple pomace landfill resulted in higher GHG emissions (1841.00 tons CO{sub 2} eq. per year). The assessment and inventory of GHG emissions during solid-state fermentation gave positive indications of environmental sustainability for the use of this strategy to manage apple pomace and other agricultural wastes, particularly in Quebec and also extended to other countries. The analysis and use of parameters in this study were drawn from various analytical approaches and data sources. There was absence of some data

Optical properties of solids

CERN Document Server

Wooten, Frederick

1972-01-01

Optical Properties of Solids covers the important concepts of intrinsic optical properties and photoelectric emission. The book starts by providing an introduction to the fundamental optical spectra of solids. The text then discusses Maxwell's equations and the dielectric function; absorption and dispersion; and the theory of free-electron metals. The quantum mechanical theory of direct and indirect transitions between bands; the applications of dispersion relations; and the derivation of an expression for the dielectric function in the self-consistent field approximation are also encompassed.

Black carbon emissions from biomass and coal in rural China

Science.gov (United States)

Zhang, Weishi; Lu, Zifeng; Xu, Yuan; Wang, Can; Gu, Yefu; Xu, Hui; Streets, David G.

2018-03-01

Residential solid fuel combustion makes a major contribution to black carbon (BC) emissions in China. A new estimation of BC emissions from rural solid biomass and coal consumption has been derived from field survey data. The following new contributions are made: (1) emission factors are collected and reviewed; (2) household energy data are collected from field survey data and from the literature; (3) a new extrapolation method is developed to extend the field survey data to other locations; (4) the ownership and usage of two stove types are estimated and considered in the emission calculations; and (5) uncertainties associated with the estimation results are quantified. It is shown that rural households with higher income will consume less biomass but more coal. Agricultural acreage and temperature also significantly influence the amount of solid fuel consumed in rural areas. It is estimated that 640 ± 245 Gg BC/y were emitted to the atmosphere due to residential solid fuel consumption in rural China in 2014. Emissions of BC from straw, wood, and coal contributed 42 ± 13%, 36 ± 15%, and 22 ± 10% of the total, respectively. We show that effective BC mitigation (a reduction of 47%) could be obtained through widespread introduction of improved stoves in rural households.

Black carbon emissions from biomass and coal in rural China

Energy Technology Data Exchange (ETDEWEB)

Zhang, Weishi; Lu, Zifeng; Xu, Yuan; Wang, Can; Gu, Yefu; Xu, Hui; Streets, David G.

2018-03-01

Residential solid fuel combustion makes a major contribution to black carbon (BC) emissions in China. A new estimation of BC emissions from rural solid biomass and coal consumption has been derived from field survey data. The following new contributions are made: (1) emission factors are collected and reviewed; (2) household energy data are collected from field survey data and from the literature; (3) a new extrapolation method is developed to extend the field survey data to other locations; (4) the ownership and usage of two stove types are estimated and considered in the emission calculations; and (5) uncertainties associated with the estimation results are quantified. It is shown that rural households with higher income will consume less biomass but more coal. Agricultural acreage and temperature also significantly influence the amount of solid fuel consumed in rural areas. It is estimated that 640±245 Gg BC/y were emitted to the atmosphere due to residential solid fuel consumption in rural China in 2014. Emissions of BC from straw, wood, and coal contributed 42±13%, 36±15%, and 22±10% of the total, respectively. We show that effective BC mitigation (a reduction of 47%) could be obtained through widespread introduction of improved stoves in rural households

Proposal for a European standard dealing with measuring methods for fine particulate emissions of solid-fuel fired furnaces; Vorschlag einer europaeischen Staubmessnorm fuer Feststoff-Feuerstaetten - Ausarbeitung und Untersuchung eines Typenpruef-Messverfahrens fuer Staubemissionen

Energy Technology Data Exchange (ETDEWEB)

Gaegauf, Ch. [Oekozentrum, Langenbruck (Switzerland); Griffin, T. [Fachhochschule Nordwestschweiz/ITFE, Muttenz (Switzerland)

2007-10-15

The European standards for type testing of solid fuel burning appliances require only the measurement of carbon monoxide emissions. Many European countries urge the standardisation committees to establish standards for the regulation of fine particulate emissions from flue gases since they face exceeding threshold values of particulate matter in the ambient air. The Technical Committee CEN/TC 295 for the standardisation of solid fuel burning appliances assigned the Centre for Appropriate Technology in Langenbruck, Switzerland with the development of a European Technical Specification (CEN TS) for the determination of particulate emission. The new draft of the TS is based on constant volume sampling (CVS) of the entire flue gas flow in a dilution tunnel. The scientific research has been done in the Swiss test laboratory for solid fuel burning appliances and boilers at the University of Applied Sciences, in Basle. The TS is designed in such a way that it can be integrated into the test cycles required by various European standards. The investigation covered work on parameters such as dilution factor, sampling temperature and isokinetics. Tests with a wood log burning appliance and a pellet stove showed that emissions in the dilution tunnel were between 7% and 26% for the pellet stove and from 40% up to 160% higher if they were sampled directly from the stack using heated gravimetric filters. It was demonstrated that the differences between the emissions seen in the dilution tunnel and those from the stack increased along with increasing levels of incomplete combustion. (author)

Electricity and combined heat and power from municipal solid waste; theoretically optimal investment decision time and emissions trading implications.

Science.gov (United States)

Tolis, Athanasios; Rentizelas, Athanasios; Aravossis, Konstantin; Tatsiopoulos, Ilias

2010-11-01

Waste management has become a great social concern for modern societies. Landfill emissions have been identified among the major contributors of global warming and climate changes with significant impact in national economies. The energy industry constitutes an additional greenhouse gas emitter, while at the same time it is characterized by significant costs and uncertain fuel prices. The above implications have triggered different policies and measures worldwide to address the management of municipal solid wastes on the one hand and the impacts from energy production on the other. Emerging methods of energy recovery from waste may address both concerns simultaneously. In this work a comparative study of co-generation investments based on municipal solid waste is presented, focusing on the evolution of their economical performance over time. A real-options algorithm has been adopted investigating different options of energy recovery from waste: incineration, gasification and landfill biogas exploitation. The financial contributors are identified and the impact of greenhouse gas trading is analysed in terms of financial yields, considering landfilling as the baseline scenario. The results indicate an advantage of combined heat and power over solely electricity production. Gasification, has failed in some European installations. Incineration on the other hand, proves to be more attractive than the competing alternatives, mainly due to its higher power production efficiency, lower investment costs and lower emission rates. Although these characteristics may not drastically change over time, either immediate or irreversible investment decisions might be reconsidered under the current selling prices of heat, power and CO(2) allowances.

Rapid targeted somatic mutation analysis of solid tumors in routine clinical diagnostics.

Science.gov (United States)

Magliacane, Gilda; Grassini, Greta; Bartocci, Paola; Francaviglia, Ilaria; Dal Cin, Elena; Barbieri, Gianluca; Arrigoni, Gianluigi; Pecciarini, Lorenza; Doglioni, Claudio; Cangi, Maria Giulia

2015-10-13

Tumor genotyping is an essential step in routine clinical practice and pathology laboratories face a major challenge in being able to provide rapid, sensitive and updated molecular tests. We developed a novel mass spectrometry multiplexed genotyping platform named PentaPanel to concurrently assess single nucleotide polymorphisms in 56 hotspots of the 5 most clinically relevant cancer genes, KRAS, NRAS, BRAF, EGFR and PIK3CA for a total of 221 detectable mutations. To both evaluate and validate the PentaPanel performance, we investigated 1025 tumor specimens of 6 different cancer types (carcinomas of colon, lung, breast, pancreas, and biliary tract, and melanomas), systematically addressing sensitivity, specificity, and reproducibility of our platform. Sanger sequencing was also performed for all the study samples. Our data showed that PentaPanel is a high throughput and robust tool, allowing genotyping for targeted therapy selection of 10 patients in the same run, with a practical turnaround time of 2 working days. Importantly, it was successfully used to interrogate different DNAs isolated from routinely processed specimens (formalin-fixed paraffin embedded, frozen, and cytological samples), covering all the requirements of clinical tests. In conclusion, the PentaPanel platform can provide an immediate, accurate and cost effective multiplex approach for clinically relevant gene mutation analysis in many solid tumors and its utility across many diseases can be particularly relevant in multiple clinical trials, including the new basket trial approach, aiming to identify appropriate targeted drug combination strategies.

Discussion of the origin of secondary photon and secondary ion emission during energetic particle irradiation of solids. I. The collision cascade

International Nuclear Information System (INIS)

Wright, R.B.; Gruen, D.M.

1980-01-01

Secondary photon and secondary ion emission during energetic particle irradiation of solid surfaces is assumed to arise due to excitation and de-excitation of sputtered particles originating from a collision cascade induced by the incident projectile. The excitation is postulated to occur by two alternative mechanisms: path (a), where excitation occurs at or very near the surface of the solid due to atom--atom or atom--electron collisions; and path (b), where excitation occurs as the sputtered particle leaves the solid, but is still under its influence so that electron exchange processes are permitted. Once the excited and/or ionized sputtered particle is formed nonradiative de-excitation processes are then included in the discussion which allow the excited and/or ionized particle to be de-excited and/or neutralized. The result of these nonradiative de-excitation processes is shown to provide a possible channel for the formation of new excited ''daughters'' by the de-excitation of the initial excited ''parent''. Depending on the initial excitation probability of the parent the new excited daughters are shown to contribute to various energy regions of the excited and/or ionized secondary particle energy distribution. A mathematical formalism is developed based on the neutral sputtered atom energy and velocity distributions assuming a collision cascade origin for these sputtered particles. By including various models for the excitation probability, and the survival probability for excited particles once formed to not undergo nonradiative de-excitation the resulting energy and velocity distributions of the sputtered excited and/or ionized secondary particles are calculated. These distributions are found to be a function of the emission angle depending on the model assumed for the initial excitation. From this formalism the total excited secondary particle yield may be calculated

Emission of muonic hydrogen isotopes from solid hydrogen layers into vacuum

International Nuclear Information System (INIS)

Marshall, G.M.; Bailey, J.M.; Beer, G.A.

1989-10-01

An attempt was made to create in vacuum free muonic hydrogen atoms, muonic protium and muonic deuterium. The method was based on slowing a beam of μ - in a layer of solid hydrogen in vacuum frozen to a cold gold foil substrate. Muonic hydrogen formed near the surface is emitted from it into the vacuum with an energy spectrum determined by the formation and subsequent scattering processes. For a typical total cross section of 10 -19 cm 2 the interaction probability is 0.43 μm -1 . For emission at an energy of order 1 eV, the muonic atom travels about 10 mm in vacuum prior to decay. No corresponding signal was observed with a deuterium layer of 6 mg/cm 2 . The natural abundance of deuterons in hydrogen leads to transfer of the muon in a mean time of about 500 ns, and because of the reduced mass difference, the m u - d obtains a kinetic energy of 45 eV, from which the atom will scatter and slow until the energy of the Ramsauer-Townsend minimum is reached and the hydrogen film becomes nearly transparent to μ - d. The Ramsauer-Townsend effect is also expected to show up for tritium in protium, which means a source of μ - t in vacuum should be possible

Sample preparation techniques in trace element analysis by X-ray emission spectroscopy

International Nuclear Information System (INIS)

Valkovic, V.

1983-11-01

The report, written under a research contract with the IAEA, contains a detailed presentation of the most difficult problem encountered in the trace element analysis by methods of the X-ray emission spectroscopy, namely the sample preparation techniques. The following items are covered. Sampling - with specific consideration of aerosols, water, soil, biological materials, petroleum and its products, storage of samples and their handling. Pretreatment of samples - preconcentration, ashing, solvent extraction, ion exchange and electrodeposition. Sample preparations for PIXE - analysis - backings, target uniformity and homogeneity, effects of irradiation, internal standards and specific examples of preparation (aqueous, biological, blood serum and solid samples). Sample preparations for radioactive sources or tube excitation - with specific examples (water, liquid and solid samples, soil, geological, plants and tissue samples). Finally, the problem of standards and reference materials, as well as that of interlaboratory comparisons, is discussed

Plasma dynamics from laser ablated solid lithium

Indian Academy of Sciences (India)

b; 52.25.-b; 52.70.-m. 1. Introduction. Pulsed laser ablation of a solid sample generates a dense plasma emission in the shape of ... The multichannel analyser plate of the ICCD was gated for as less as 4 ns using ... to explain the atomic collision processes [4]. .... Within duration of laser pulse, there occurs laser-solid interac-.

A Bragg curve counter with an internal production target for the measurement of the double-differential cross-section of fragment production induced by neutrons at energies of tens of MeV

International Nuclear Information System (INIS)

Sanami, T.; Hagiwara, M.; Oishi, T.; Hosokawa, M.; Kamada, S.; Tanaka, Su.; Iwamoto, Y.; Nakashima, H.; Baba, M.

2009-01-01

A Bragg curve counter equipped with an internal production target was developed for the measurements of double-differential cross-sections of fragment production induced by neutrons at energies of tens of MeV. The internal target permitted a large detection solid angle and thus the registration of processes at low production rates. In this specific geometry, the detection solid angle depends on the emission angle and the range of the particle. Therefore the energy, atomic number, and angle of trajectory of the particle have to be taken into account for the determination of the solid angle. For the selection of events with tracks confined within a defined cylindrical volume around the detector axis, a segmented anode was applied. The double-differential cross-sections for neutron-induced production of lithium, beryllium, and boron fragments from a carbon target were measured at 0 deg. for 65 MeV neutrons. The results are in good agreement with theoretical calculation using PHITS code with GEM and ISOBAR model.

The next step in Europe's climate action. Setting targets for 2030. Reviving the EU emissions trading system and bringing EU greenhouse gas emissions on a 2C track. Policy brief

Energy Technology Data Exchange (ETDEWEB)

Hoehne, N.; Gilbert, A.; Hagemann, M.; Fekete, H.; Lam, Long; De Vos, R. [Ecofys, Utrecht (Netherlands)

2013-06-15

This paper explains how setting 2030 targets will reinvigorate the ETS and will put EU emissions on track to limit global temperature increase below two degrees Celsius (2C). This paper describes four key findings for EU policymakers engaged in preparing EU energy and climate measures for 2030 and for the longer term. The European Commission estimates that by 2020, the companies participating in the ETS will have accumulated a surplus of 1.5 to 2.3 billion allowances, which may be banked and used beyond 2020. This is about the same size as the annual emissions budget of ETS companies (just below 2 billion tonnes). Applying equity principles to the global distribution of efforts in reaching the 2C goal, an indicative 'fair' EU contribution would be a reduction of EU greenhouse gas emissions by around 49% (median of a full range from 39 to 79%) by 2030 compared to 1990 levels. The 2030 targets can be set in a way to also accommodate the surplus expected until 2020. If the entire surplus of allowances from the ETS were to be used after 2020, the 2030 target has to become around 7 percentage points more stringent to compensate for that. Alternatively, the trajectory of the target from 2021 to 2030 could be set to compensate for the surplus. In addition, a more ambitious trajectory towards 2030 would cast its shadow on the mitigation in the period 2013-2020. It would strengthen the ETS, in conjunction with any other ETS recalibration options such as shifting the auctioning ('backloading') or cancelling allowances before 2020.

Effect of hydraulic retention time and sludge recirculation on greenhouse gas emission and related microbial communities in two-stage membrane bioreactor treating solid waste leachate.

Science.gov (United States)

Nuansawan, Nararatchporn; Boonnorat, Jarungwit; Chiemchaisri, Wilai; Chiemchaisri, Chart

2016-06-01

Methane (CH4) and nitrous oxide (N2O) emissions and responsible microorganisms during the treatment of municipal solid waste leachate in two-stage membrane bioreactor (MBR) was investigated. The MBR system, consisting of anaerobic and aerobic stages, were operated at hydraulic retention time (HRT) of 5 and 2.5days in each reactor under the presence and absence of sludge recirculation. Organic and nitrogen removals were more than 80% under all operating conditions during which CH4 emission were found highest under no sludge recirculation condition at HRT of 5days. An increase in hydraulic loading resulted in a reduction in CH4 emission from anaerobic reactor but an increase from the aerobic reactor. N2O emission rates were found relatively constant from anaerobic and aerobic reactors under different operating conditions. Diversity of CH4 and N2O producing microorganisms were found decreasing when hydraulic loading rate to the reactors was increased. Copyright © 2016 Elsevier Ltd. All rights reserved.

Design a 10 kJ IS Mather Type Plasma Focus for Solid Target Activation to Produce Short-Lived Radioisotopes 12C(d,n)13N

Science.gov (United States)

Sadat Kiai, S. M.; Adlparvar, S.; Sheibani, S.; Elahi, M.; Safarien, A.; Farhangi, S.; Zirak, A. R.; Alhooie, S.; Mortazavi, B. N.; Khalaj, M. M.; Khanchi, A. R.; Dabirzadeh, A. A.; Kashani, A.; Zahedi, F.

2010-10-01

A 10 kJ (15 kV, 88 μF) IS (Iranian Sun) Mather type plasma focus device has been studied to determine the activity of a compound exogenous carbon solid target through 12C(d,n)13N nuclear reaction. The produced 13N is a short-lived radioisotope with a half-life of 9.97 min and threshold energy of 0.28 MeV. The results indicate that energetic deuterons impinging on the solid target can produce yield of = 6.7 × 10-5 with an activity of A = 6.8 × 104 Bq for one plasma focus shut and A ν = 4 × 105 Bq for 6 shut per mint when the projectile maximum deuterons energy is E max = 3 MeV.

Co-composting of municipal solid waste mixed with matured sewage sludge: The relationship between N2O emissions and denitrifying gene abundance.

Science.gov (United States)

Bian, Rongxing; Sun, Yingjie; Li, Weihua; Ma, Qiang; Chai, Xiaoli

2017-12-01

Aerobic composting is an alternative measure to the disposal of municipal solid waste (MSW). However, it produces nitrous oxide (N 2 O), a highly potent greenhouse via microbial nitrification and denitrification. In this study, the effects of matured sewage sludge (MSS) amendment on N 2 O emissions and the inter-relationships between N 2 O emissions and the abundance of denitrifying bacteria were investigated during aerobic composting of MSW. The results demonstrated that MSW composting with MSS amendments (C1, and C2, with a MSW to MSS ratio of 2:1 and 4:1, (v/v), respectively) significantly increased N 2 O emissions during the initial stage, yet contributed to the mitigation of N 2 O emissions during the cooling and maturation stage. MSS amended composting emitted a total of 18.4%-25.7% less N 2 O than the control treatment without MSS amendment (CK). Matured sewage sludge amendment also significantly altered the abundance of denitrifying bacteria. The quantification of denitrifying functional genes revealed that the N 2 O emission rate had a significant positive correlation with the abundance of the nirS, nirK genes in both treatments with MSS amendment. The nosZ/(nirS + nirK) ratio could be a good indicator for predicting N 2 O emissions. The higher N 2 O emission rate during the initial stage of composting mixed with MSS was characterized by lower nosZ/(nirS + nirK) ratios, compared to CK treatment. Higher ratios of nosZ/(nirS + nirK) were measured during the cooling and maturation stage in treatments with MSS which resulted in a reduction of the N 2 O emissions. These results demonstrated that MSS amendment could be a valid strategy for mitigating N 2 O emissions during MSW composting. Copyright © 2017 Elsevier Ltd. All rights reserved.

40 CFR 63.7541 - How do I demonstrate continuous compliance under the emission averaging provision?

Science.gov (United States)

2010-07-01

... solid fuel boilers participating in the emissions averaging option as determined in § 63.7522(f) and (g... this section. (i) For each existing solid fuel boiler participating in the emissions averaging option... below the applicable limit. (ii) For each group of boilers participating in the emissions averaging...

Assessment of carbon footprint emissions and environmental concerns of solid waste treatment and disposal techniques; case study of Malaysia.

Science.gov (United States)

Malakahmad, Amirhossein; Abualqumboz, Motasem S; Kutty, Shamsul Rahman M; Abunama, Taher J

2017-12-01

Malaysian authorities has planned to minimize and stop when applicable unsanitary dumping of waste as it puts human health and the environment at elevated risk. Cost, energy and revenue are mostly adopted to draw the blueprint of upgrading municipal solid waste management system, while the carbon footprint emissions criterion rarely acts asa crucial factor. This study aims to alert Malaysian stakeholders on the uneven danger of carbon footprint emissions of waste technologies. Hence, three scenarios have been proposed and assessed mainly on the carbon footprint emissions using the 2006 IPCC methodology. The first scenario is waste dumping in sanitary landfills equipped with gas recovery system, while the second scenario includes anaerobic digestion of organics and recycling of recyclable wastes such as plastic, glass and textile wastes. The third scenario is waste incineration. Besides the carbon footprint emissions criterion, other environmental concerns were also examined. The results showed that the second scenario recorded the lowest carbon footprint emissions of 0.251t CO 2 eq./t MSW while the third scenario had the highest emissions of 0.646t CO 2 eq./t MSW. Additionally, the integration between anaerobic digestion and recycling techniques caused the highest avoided CO 2 eq. emissions of 0.74t CO 2 eq./t MSW. The net CO 2 eq. emissions of the second scenario equaled -0.489t CO 2 eq./t MSW due to energy recovery from the biogas and because of recycled plastic, glass and textile wastes that could replace usage of raw material. The outcomes also showed that the first scenario generates huge amount of leachate and hazardous air constituents. The study estimated that a ton of dumped waste inside the landfills generates approximately 0.88m 3 of trace risky compounds and 0.188m 3 of leachate. As for energy production, the results showed that the third scenario is capable of generating 639kWh/t MSW followed by the second scenario with 387.59kWh/t MSW. The first

Integration of a municipal solid waste gasification plant with solid oxide fuel cell and gas turbine

DEFF Research Database (Denmark)

Bellomare, Filippo; Rokni, Masoud

2013-01-01

An interesting source of producing energy with low pollutants emission and reduced environmental impact are the biomasses; particularly using Municipal Solid Waste (MSW) as fuel, can be a competitive solution not only to produce energy with negligible costs but also to decrease the storage...... in landfills. A Municipal Solid Waste Gasification Plant Integrated with Solid Oxide Fuel Cell (SOFC) and Gas Turbine (GT) has been studied and the plant is called IGSG (Integrated Gasification SOFC and GT). Gasification plant is fed by MSW to produce syngas by which the anode side of an SOFC is fed wherein...

Composite hydrogen-solid methane moderators

International Nuclear Information System (INIS)

Picton, D.; Bennington, S.; Ansell, S.; Fernandez-Garcia, J.; Broome, T.

2004-01-01

This paper describes the results of Monte-Carlo calculations for a coupled moderator on a low-power pulsed neutron spallation source and is part of the design study for a second target station for the ISIS spallation source. Various options were compared including hydrogen, solid methane, grooving the solid methane and compound moderators made of hydrogen in front of solid methane. To maximise the neutron current at low energies two strategies appear to emerge from the calculations. For instruments that view a large area of moderator surface a layer of hydrogen in front of a thin solid-methane moderator is optimum, giving a gain of about a factor 10 relative to the current liquid hydrogen moderator on the existing ISIS tantalum target. For instruments that only view a restricted area higher flux, corresponding to a gain of 13.5, can be achieved with the use of a single groove or re-entrant hole in the moderator. (orig.)

Delivery of kinesin spindle protein targeting siRNA in solid lipid nanoparticles to cellular models of tumor vasculature

International Nuclear Information System (INIS)

Ying, Bo; Campbell, Robert B.

2014-01-01

Highlights: • siRNA-lipid nanoparticles are solid particles not lipid bilayers with aqueous core. • High, but not low, PEG content can prevent nanoparticle encapsulation of siRNA. • PEG reduces cellular toxicity of cationic nanoparticles in vitro. • PEG reduces zeta potential while improving gene silencing of siRNA nanoparticles. • Kinesin spindle protein can be an effective target for tumor vascular targeting. - Abstract: The ideal siRNA delivery system should selectively deliver the construct to the target cell, avoid enzymatic degradation, and evade uptake by phagocytes. In the present study, we evaluated the importance of polyethylene glycol (PEG) on lipid-based carrier systems for encapsulating, and delivering, siRNA to tumor vessels using cellular models. Lipid nanoparticles containing different percentage of PEG were evaluated based on their physical chemical properties, density compared to water, siRNA encapsulation, toxicity, targeting efficiency and gene silencing in vitro. siRNA can be efficiently loaded into lipid nanoparticles (LNPs) when DOTAP is included in the formulation mixture. However, the total amount encapsulated decreased with increase in PEG content. In the presence of siRNA, the final formulations contained a mixed population of particles based on density. The major population which contains the majority of siRNA exhibited a density of 4% glucose, and the minor fraction associated with a decreased amount of siRNA had a density less than PBS. The inclusion of 10 mol% PEG resulted in a greater amount of siRNA associated with the minor fraction. Finally, when kinesin spindle protein (KSP) siRNA was encapsulated in lipid nanoparticles containing a modest amount of PEG, the proliferation of endothelial cells was inhibited due to the efficient knock down of KSP mRNA. The presence of siRNA resulted in the formation of solid lipid nanoparticles when prepared using the thin film and hydration method. LNPs with a relatively modest amount of

Greenhouse gases emission from municipal waste management: The role of separate collection.

Science.gov (United States)

Calabrò, Paolo S

2009-07-01

The municipal solid waste management significantly contributes to the emission in the atmosphere of greenhouse gases (e.g. CO(2), CH(4), N(2)O) and therefore the management process from collection to treatment and disposal has to be optimized in order to reduce these emissions. In this paper, starting from the average composition of undifferentiated municipal solid waste in Italy, the effect of separate collection on greenhouse gases emissions from municipal waste management has been assessed. Different combinations of separate collection scenarios and disposal options (i.e. landfilling and incineration) have been considered. The effect of energy recovery from waste both in landfills and incinerators has also been addressed. The results outline how a separate collection approach can have a significant effect on the emission of greenhouse gases and how wise municipal solid waste management, implying the adoption of Best Available Technologies (i.e. biogas recovery and exploitation system in landfills and energy recovery system in Waste to Energy plants), can not only significantly reduce greenhouse gases emissions but, in certain cases, can also make the overall process a carbon sink. Moreover it has been shown that separate collection of plastic is a major issue when dealing with global warming relevant emissions from municipal solid waste management.

Current status of solid state target technologies

International Nuclear Information System (INIS)

Schlyer, David J.; Ferrieri, Richard A.

2000-01-01

In general radioisotopes fall into two basic groups: those that are neutron rich and those that are neutron deficient. Those that are neutron rich are usually made in a nuclear reactor while those that are neutron deficient are produced by bombarding a suitable target with protons, deuterons or helium particles. Particle accelerators and in particular cyclotrons, were very important in the preparation of radioisotopes during the years of 1935 to the end of World War Two. The amount of radioactive material which could be produced in an accelerator was many times greater than the amount which could be produced using the alpha particles from naturally occurring radioactive elements. After World War Two, reactors were used to produce radioactive elements and the use of accelerators for this purpose became less common. However, as the techniques for using radiotracers became more sophisticated, it became clear that reactor produced radionuclides could not satisfy the growing demands and therefore accelerators were needed to produce new radioisotopes which could be used in new ways. There are three major reasons the accelerator produced radioisotopes are used more widely that reactor produced radionuclides. These are: 1) The radioisotopes produced in a reactor may have unfavorable decay characteristics (particle emission, half-life, gamma rays, etc.) for a particular application. 2) The radioisotope cannot be produced in a reactor with high specific activity. 3) Access to a reactor is limited. The number of reactors available has become many fewer than the number of cyclotrons available to the scientific community, or the radioisotope has too short a half-life to be transported to the site where it is needed. There are a wide variety of nuclear reactions which are used in an accelerator to produce the artificial radioactivity. The bombarding particles are usually protons, deuterons, or helium particles. The energies which are used range from a few MeV to hundreds of Me

Fuel-related Emissions from the Croatian Municipal Solid Waste Collection System in 2013: Mixed Municipal Waste

Directory of Open Access Journals (Sweden)

Anamarija Grbeš

2018-01-01

Full Text Available Waste removal (collection and landfilling in the Republic of Croatia is the responsibility of the municipalities and local governments in 21 administrative units (counties. They entrust the respective economic activity to 208 private and public companies specialized in waste collection and treatment. Organised waste collection affects 99 % of the population. The mixed waste from households and enterprises is at various frequencies collected at the door (kerbside collection and transported by truck to a landfill, or processing plant. This article aims to estimate fuel consumption and fuel-related airborne emissions from the collection of mixed municipal waste in Croatia in 2013. The input data and emission results are shown for Croatia and each Croatian county, in total, and relative to the number of inhabitants and mass of collected waste. Annual consumption of diesel for the collection of mixed waste is estimated at 10.6 million litres. At the county level, fuel consumption ranges from 87 thousand litres to 2.2 million litres, on average 504 thousand litres per county. Total emission of CO2 is estimated at 28 000 t, which at county level ranges from 231 to 5711 t. Relative emission ranges from 3.3 to 13 kg CO2 per capita (average 6.6 kg per capita, or 8.6–28.1 kg t−1 of municipal waste (average 17 kg CO2 per ton of municipal waste. The average values of CO2 emission from MSW collection that should also be the target values are 7–9 kg for mixed waste, and 8–15 kg CO2 for separate waste streams. Apart from CO2 emission, this research estimates emission of other, diesel combustion related compounds, such as NOx, CO, lubricant related CO2, NMVOC, PM, f-BC, N2O, SO2, NH3, Pb, ID[1,2,3-cd]P, B[k]F, B[b]F, B[a]P, as well as total distance of transport.

Growth and solid/solid transformation in a Ni-Si eutectic alloy

Energy Technology Data Exchange (ETDEWEB)

Dutra, A.T. [Department of Materials Engineering, State University of Campinas, P.O. Box 6122, Campinas 13083-970, SP (Brazil); Ferrandini, P.L. [Department of Materials Engineering, State University of Campinas, P.O. Box 6122, Campinas 13083-970, SP (Brazil); Costa, C.A.R. [Institute of Chemistry, State University of Campinas, P.O. Box 6154, Campinas 13083-970, SP (Brazil); Goncalves, M.C. [Institute of Chemistry, State University of Campinas, P.O. Box 6154, Campinas 13083-970, SP (Brazil); Caram, R. [Department of Materials Engineering, State University of Campinas, P.O. Box 6122, Campinas 13083-970, SP (Brazil)]. E-mail: rcaram@fem.unicamp.br

2005-08-16

High temperature structural components demand materials that maintain satisfactory mechanical and chemical characteristics. These needs may be met by applying some eutectic alloys, including Ni-Ni{sub 3}Si. This paper deals with the directional solidification of Ni-Ni{sub 3}Si grown under several growth rates. The analysis of the eutectic microstructure was carried out using atomic force microscopy (AFM) and field emission scanning electron microscopy (FESEM). The results obtained provided a precise analysis of the Ni{sub 3}Si phase. It could be noticed that the solid/solid transformations by which Ni{sub 3}Si phase goes through, deeply affects its morphology. In addition, quantitative information on the eutectic structure was obtained. It was confirmed that the growth rate variation deeply affects the final microstructure as it influences the efficiency of atomic diffusion along the solid/liquid interface.

Growth and solid/solid transformation in a Ni-Si eutectic alloy

International Nuclear Information System (INIS)

Dutra, A.T.; Ferrandini, P.L.; Costa, C.A.R.; Goncalves, M.C.; Caram, R.

2005-01-01

High temperature structural components demand materials that maintain satisfactory mechanical and chemical characteristics. These needs may be met by applying some eutectic alloys, including Ni-Ni 3 Si. This paper deals with the directional solidification of Ni-Ni 3 Si grown under several growth rates. The analysis of the eutectic microstructure was carried out using atomic force microscopy (AFM) and field emission scanning electron microscopy (FESEM). The results obtained provided a precise analysis of the Ni 3 Si phase. It could be noticed that the solid/solid transformations by which Ni 3 Si phase goes through, deeply affects its morphology. In addition, quantitative information on the eutectic structure was obtained. It was confirmed that the growth rate variation deeply affects the final microstructure as it influences the efficiency of atomic diffusion along the solid/liquid interface

Thermal drying of the solid fraction from biogas digestate

DEFF Research Database (Denmark)

Pantelopoulos, Athanasios; Magid, Jakob; Jensen, Lars Stoumann

2016-01-01

Drying of solids produced from digestate is prone to N losses through NH3 volatilisation. The applicability of acidification as an NH3 emission mitigation technique during the drying of solids from digestate was assessed in a drying experiment. Operating conditions comprised four drying temperatu...

Design of Solid Form Xenon-124 Target for Producing I-123 Radioisotope Using Computer Simulation Techniques

International Nuclear Information System (INIS)

Kamali Moghaddam, K.; Sadeghi, M.; Kakavand, T.; Shokri Bonab, S.

2006-01-01

Recently in Cyclotron and Nuclear Medicine Department of NRCAM, at Atomic Energy organization of Iran (AEOI), a system for producing 1-123 via Xe-124 gas target technology, has been constructed and installed. One of the major problems in this system is the highly expensive cost of the enriched Xenon-124 gas. Therefore, saving this gas inside the system is very important. Unfortunately, by accidental rupture of the window foil or bad function of O-rings, the whole Xenon gas will escape from the system immediately. In this paper, by using computer codes; ALICE91, SRIM and doing some calculations we are going to demonstrate our latest effort for feasibility study of producing I-123 with the above mentioned reactions, but using Xe-124 solid target instead. According to our suggested design, a conical shaped irradiation vessel made of copper with 1 mm thickness, 1 cm outlet diameter, 5 cm length and 12 deg. angle at summit can be fixed inside a liquid nitrogen housing chamber. The Xenon-124 gas will be sent to the inside of this very cold conical trap and eventually deposited on its surface in solid form. Our calculation shows that during bombardment with 17-28 MeV proton energy, the thickness of solidified Xenon layer will remain around .28 mm. Likewise; thermo-dynamical calculation shows that in order to prevent the evaporation of solidified Xenon, the maximum permissible proton beam current for this system should be less than 1.4 μA. According to these working conditions, the production yield of I-123 can be predicted to be around 150 mCi/μAh. (authors)

The causes of the municipal solid waste and the greenhouse gas emissions from the waste sector in the United States.

Science.gov (United States)

Lee, Seungtaek; Kim, Jonghoon; Chong, Wai K O

2016-10-01

The United States generated approximately 730kg of waste per capita in 2013, which is the highest amount of waste among OECD countries. The waste has adverse effects to human health and the environment. One of the most serious adverse effects is greenhouse gas emissions, especially methane (CH4), which causes global warming. However, the United States' amount of waste generation is not decreasing, and the recycling rate is only 26%, which is lower than other OECD countries. In order to decrease waste generation and greenhouse gas emissions, identifying the causality of the waste generation and greenhouse gas emissions from waste sector should be made a priority. The research objective is to verify whether the Environmental Kuznets Curve relationship is supported for waste generation and GDP across the U.S. Moreover, it also confirmed that total waste generation and recycling of waste influences carbon dioxide emissions from the waste sector. Based on the results, critical insight and suggestions were offered to policymakers, which is the potential way to lower the solid waste and greenhouse gas emissions from the waste sector. This research used annually based U.S. data from 1990 to 2012, and these data were collected from various data sources. To verify the causal relationship, the Granger causality test was applied. The results showed that there is no causality between GDP and waste generation, but total waste and recycling generate significantly increasing and decreasing greenhouse gas emissions from the waste sector, respectively. This implies that waste generation will not decrease even if GDP increases. And, if waste generation decreases or the recycling rate increases, greenhouse gas emission will decrease. Based on these results, increasing the recycling rate is first suggested. The second suggestion is to break the causal relationship between MSW and greenhouse gas emission from the waste sector. The third is that the U.S. government should benchmark a

Life cycle assessment of municipal solid waste management with regard to greenhouse gas emissions: Case study of Tianjin, China

International Nuclear Information System (INIS)

Zhao Wei; Voet, Ester van der; Zhang Yufeng; Huppes, Gjalt

2009-01-01

The environmental impacts of municipal solid waste (MSW) management have been highlighted in China, due to the continually increasing amount of MSW being generated and the limited capacity of waste treatment facilities. Of particular interest is greenhouse gas (GHG) mitigation, aided by the Kyoto Mechanisms. China is an important case study for this global issue; however, an analysis of the entire life cycle of MSW management on GHG emissions is not available for China. This study evaluates the current and possible patterns of MSW management with regard to GHG emissions, using life cycle assessment (LCA), based on the Tianjin case. We assess the baseline scenario, reflecting the existing MSW management system, as well as a set of alternative scenarios, five exploring waste treatment technology innovations and one exploring integrated MSW management, to quantitatively predict potentials of GHG mitigation for Tianjin. Additionally, a sensitivity analysis is used to investigate the influence of landfill gas (LFG) collection efficiency, recycling rate and methodological choice, especially allocation, on the outcomes. The results show GHG emissions from Tianjin's MSW management system amount to 467.34 Mg CO 2 eq. per year, based on the treatment of MSW collected in the central districts in 2006, and the key issue is LFG released. The integrated MSW management scenario, combining different improvement options, shows the highest GHG mitigation potential. Given the limited financial support and the current waste management practice in Tianjin, LFG utilization scenario would be the preferred choice. The sensitivity analysis of recycling rate shows an approximately linear relation of inverse proportion between recycling rate and total GHG emissions. Kitchen waste composting makes a considerable contribution to total GHG emissions reduction. Allocation choices result in differences in total quantitative outcomes, but preference orders and contributions analysis are found to

Life cycle assessment of municipal solid waste management with regard to greenhouse gas emissions: Case study of Tianjin, China

Energy Technology Data Exchange (ETDEWEB)

Zhao Wei [School of Environmental Science and Engineering, Tianjin University, Weijin Road 92, Nankai District 300072 (China); Institute of Environmental Sciences (CML), Leiden University, P. O. Box 9518, 2300RA, Leiden (Netherlands)], E-mail: zhao@cml.leidenuniv.nl; Voet, Ester van der [Institute of Environmental Sciences (CML), Leiden University, P. O. Box 9518, 2300RA, Leiden (Netherlands); Zhang Yufeng [School of Environmental Science and Engineering, Tianjin University, Weijin Road 92, Nankai District 300072 (China); Huppes, Gjalt [Institute of Environmental Sciences (CML), Leiden University, P. O. Box 9518, 2300RA, Leiden (Netherlands)

2009-02-15

The environmental impacts of municipal solid waste (MSW) management have been highlighted in China, due to the continually increasing amount of MSW being generated and the limited capacity of waste treatment facilities. Of particular interest is greenhouse gas (GHG) mitigation, aided by the Kyoto Mechanisms. China is an important case study for this global issue; however, an analysis of the entire life cycle of MSW management on GHG emissions is not available for China. This study evaluates the current and possible patterns of MSW management with regard to GHG emissions, using life cycle assessment (LCA), based on the Tianjin case. We assess the baseline scenario, reflecting the existing MSW management system, as well as a set of alternative scenarios, five exploring waste treatment technology innovations and one exploring integrated MSW management, to quantitatively predict potentials of GHG mitigation for Tianjin. Additionally, a sensitivity analysis is used to investigate the influence of landfill gas (LFG) collection efficiency, recycling rate and methodological choice, especially allocation, on the outcomes. The results show GHG emissions from Tianjin's MSW management system amount to 467.34 Mg CO{sub 2} eq. per year, based on the treatment of MSW collected in the central districts in 2006, and the key issue is LFG released. The integrated MSW management scenario, combining different improvement options, shows the highest GHG mitigation potential. Given the limited financial support and the current waste management practice in Tianjin, LFG utilization scenario would be the preferred choice. The sensitivity analysis of recycling rate shows an approximately linear relation of inverse proportion between recycling rate and total GHG emissions. Kitchen waste composting makes a considerable contribution to total GHG emissions reduction. Allocation choices result in differences in total quantitative outcomes, but preference orders and contributions analysis are

Trapping and re-emission of energetic hydrogen and helium ions in materials

International Nuclear Information System (INIS)

Yamaguchi, Sadae

1981-01-01

The experimental results on the trapping and re-emission of energetic hydrogen and helium ions in materials are explained. The trapping of deuterium and helium in graphite saturates at the concentration of 10 18 ions/cm 2 . The trapping rate of hydrogen depends on the kinds of target materials. In the case of the implantation in Mo over 3 x 10 16 H/cm 2 , hydrogen is hardly trapped. On the other hand, the trapping of hydrogen in Ti, Zr and Ta which form solid solution is easily made. The hydrogen in these metals can diffuse toward the inside of metals. The deuterium retained in 316 SS decreased with time. The trapping rate reached saturation more rapidly at higher implantation temperature. The effective diffusion constant for the explanation of the re-emission process is 1/100 as small as the ordinary value. The radiation damage due to helium irradiation affects on the trapping of deuterium in Mo. The temperature dependence of the trapping rate can be explained by the diffusion model based on the Sievert's law. The re-emission of helium was measured at various temperature. At low temperature, the re-emission was low at first, then the rate increased. At high temperature, the re-emission rate was high from the beginning. (Kato, T.)

Modeling emission rates and exposures from outdoor cooking

Science.gov (United States)

Edwards, Rufus; Princevac, Marko; Weltman, Robert; Ghasemian, Masoud; Arora, Narendra K.; Bond, Tami

2017-09-01

Approximately 3 billion individuals rely on solid fuels for cooking globally. For a large portion of these - an estimated 533 million - cooking is outdoors, where emissions from cookstoves pose a health risk to both cooks and other household and village members. Models that estimate emissions rates from stoves in indoor environments that would meet WHO air quality guidelines (AQG), explicitly don't account for outdoor cooking. The objectives of this paper are to link health based exposure guidelines with emissions from outdoor cookstoves, using a Monte Carlo simulation of cooking times from Haryana India coupled with inverse Gaussian dispersion models. Mean emission rates for outdoor cooking that would result in incremental increases in personal exposure equivalent to the WHO AQG during a 24-h period were 126 ± 13 mg/min for cooking while squatting and 99 ± 10 mg/min while standing. Emission rates modeled for outdoor cooking are substantially higher than emission rates for indoor cooking to meet AQG, because the models estimate impact of emissions on personal exposure concentrations rather than microenvironment concentrations, and because the smoke disperses more readily outdoors compared to indoor environments. As a result, many more stoves including the best performing solid-fuel biomass stoves would meet AQG when cooking outdoors, but may also result in substantial localized neighborhood pollution depending on housing density. Inclusion of the neighborhood impact of pollution should be addressed more formally both in guidelines on emissions rates from stoves that would be protective of health, and also in wider health impact evaluation efforts and burden of disease estimates. Emissions guidelines should better represent the different contexts in which stoves are being used, especially because in these contexts the best performing solid fuel stoves have the potential to provide significant benefits.

Reducing ammonia emissions in Europe

DEFF Research Database (Denmark)

Jacobsen, Brian H.

2011-01-01

The NEC directive has set targets for the 2010 ammonia emissions from a number of European countries. The target will be reached by most EU-countries and the total emission for EU-27 has been reduced by 22% from 1990 to 2007. Denmark is one of the countries with the largest reductions since 1990...

Drug-targeting methodologies with applications: A review

Science.gov (United States)

Kleinstreuer, Clement; Feng, Yu; Childress, Emily

2014-01-01

Targeted drug delivery to solid tumors is a very active research area, focusing mainly on improved drug formulation and associated best delivery methods/devices. Drug-targeting has the potential to greatly improve drug-delivery efficacy, reduce side effects, and lower the treatment costs. However, the vast majority of drug-targeting studies assume that the drug-particles are already at the target site or at least in its direct vicinity. In this review, drug-delivery methodologies, drug types and drug-delivery devices are discussed with examples in two major application areas: (1) inhaled drug-aerosol delivery into human lung-airways; and (2) intravascular drug-delivery for solid tumor targeting. The major problem addressed is how to deliver efficiently the drug-particles from the entry/infusion point to the target site. So far, most experimental results are based on animal studies. Concerning pulmonary drug delivery, the focus is on the pros and cons of three inhaler types, i.e., pressurized metered dose inhaler, dry powder inhaler and nebulizer, in addition to drug-aerosol formulations. Computational fluid-particle dynamics techniques and the underlying methodology for a smart inhaler system are discussed as well. Concerning intravascular drug-delivery for solid tumor targeting, passive and active targeting are reviewed as well as direct drug-targeting, using optimal delivery of radioactive microspheres to liver tumors as an example. The review concludes with suggestions for future work, considereing both pulmonary drug targeting and direct drug delivery to solid tumors in the vascular system. PMID:25516850