WorldWideScience

Sample records for solid electrolyte interphase

  1. Highly Quantitative Electrochemical Characterization of Non-Aqueous Electrolytes & Solid Electrolyte Interphases

    Energy Technology Data Exchange (ETDEWEB)

    Sergiy V. Sazhin; Kevin L. Gering; Mason K. Harrup; Harry W. Rollins

    2012-10-01

    The methods to measure solid electrolyte interphase (SEI) electrochemical properties and SEI formation capability of non-aqueous electrolyte solutions are not adequately addressed in the literature. And yet, there is a strong demand in new electrolyte generations that promote stabilized SEIs and have an influence to resolve safety, calendar life and other limitations of Li-ion batteries. To fill this gap, in situ electrochemical approach with new descriptive criteria for highly quantitative characterization of SEI and electrolytes is proposed. These criteria are: SEI formation capacity, SEI corrosion rate, SEI maintenance rate, and SEI kinetic stability. These criteria are associated with battery parameters like irreversible capacity, self-discharge, shelf-life, power, etc. Therefore, they are especially useful for electrolyte development and standard fast screening, allowing a skillful approach to narrow down the search for the best electrolyte. The characterization protocol also allows retrieving information on interfacial resistance for SEI layers and the electrochemical window of electrolytes, the other important metrics of characterization. The method validation was done on electrolyte blends containing phosphazenes, developed at Idaho National Laboratory, as 1.2M LiPF6 [80 % EC-MEC (2:8) (v/v) + 20% Phosphazene variety] (v/v), which were targeted for safer electrolyte variations.

  2. Confined Solid Electrolyte Interphase Growth Space with Solid Polymer Electrolyte in Hollow Structured Silicon Anode for Li-Ion Batteries.

    Science.gov (United States)

    Ma, Tianyi; Yu, Xiangnan; Cheng, Xiaolu; Li, Huiyu; Zhu, Wentao; Qiu, Xinping

    2017-04-19

    Silicon anodes for lithium-ion batteries are of much interest owing to their extremely high specific capacity but still face some challenges, especially the tremendous volume change which occurs in cycling and further leads to the disintegration of electrode structure and excessive growth of solid electrolyte interphase (SEI). Here, we designed a novel approach to confine the inward growth of SEI by filling solid polymer electrolyte (SPE) into pores of hollow silicon spheres. The as-prepared composite delivers a high specific capacity of more than 2100 mAh g -1 and a long-term cycle stability with a reversible capacity of 1350 mAh g -1 over 500 cycles. The growing behavior of SEI was investigated by electrochemical impedance spectroscopy and differential scanning calorimetry, and the results revealed that SPE occupies the major space of SEI growth and thus confines its excessive growth, which significantly improves cycle performance and Coulombic efficiency of cells embracing hollow silicon spheres.

  3. Electrolyte Volume Effects on Electrochemical Performance and Solid Electrolyte Interphase in Si-Graphite/NMC Lithium-Ion Pouch Cells.

    Science.gov (United States)

    An, Seong Jin; Li, Jianlin; Daniel, Claus; Meyer, Harry M; Trask, Stephen E; Polzin, Bryant J; Wood, David L

    2017-06-07

    This study aims to explore the correlations between electrolyte volume, electrochemical performance, and properties of the solid electrolyte interphase in pouch cells with Si-graphite composite anodes. The electrolyte is 1.2 M LiPF6 in ethylene carbonate:ethylmethyl carbonate with 10 wt % fluoroethylene carbonate. Single layer pouch cells (100 mA h) were constructed with 15 wt % Si-graphite/LiNi0.5Mn0.3CO0.2O2 electrodes. It is found that a minimum electrolyte volume factor of 3.1 times to the total pore volume of cell components (cathode, anode, and separator) is needed for better cycling stability. Less electrolyte causes increases in ohmic and charge transfer resistances. Lithium dendrites are observed when the electrolyte volume factor is low. The resistances from the anodes become significant as the cells are discharged. Solid electrolyte interphase thickness grows as the electrolyte volume factor increases and is nonuniform after cycling.

  4. Artificial Solid Electrolyte Interphase to Address the Electrochemical Degradation of Silicon Electrodes

    Energy Technology Data Exchange (ETDEWEB)

    Dudney, Nancy J [ORNL; Nanda, Jagjit [ORNL; Liang, Chengdu [ORNL; Li, Juchuan [ORNL

    2014-01-01

    Electrochemical degradation on Si anodes prevents them from being successfully used in lithium-ion full cells. Unlike the case of graphite anodes, natural solid electrolyte interphase (SEI) films generated from carbonate electrolyte do not self-passivate on Si and causes continuous electrolyte decomposition. In this work we aim at solving the issue of electrochemical degradation by fabricating artificial SEI films using a solid electrolyte material, lithium phosphor oxynitride (Lipon), that conducts Li ions and blocks electrons. For Si anodes coated with Lipon of 50 nm or thicker, significant effect is observed in suppressing the electrolyte decomposition, while Lipon of thinner than 40 nm has little effect. Ionic and electronic conductivity measurement reveals that the artificial SEI is effective when it is a pure ionic conductor, and the electrolyte decomposition is not suppressed when the artificial SEI is a mixed electronic-ionic conductor. The critical thickness for this transition in conducting behavior is found to be 40~50 nm. This work provides guidance for designing artificial SEI for high capacity lithium-ion battery electrodes using solid electrolyte materials.

  5. Tuning the Solid Electrolyte Interphase for Selective Li- and Na-Ion Storage in Hard Carbon

    Energy Technology Data Exchange (ETDEWEB)

    Soto, Fernando A. [Department of Chemical Engineering, Texas A& M University, College Station TX 77843-3122 USA; Yan, Pengfei [Pacific Northwest National Laboratory, 902 Battelle Boulevard Richland WA 99354 USA; Engelhard, Mark H. [Pacific Northwest National Laboratory, 902 Battelle Boulevard Richland WA 99354 USA; Marzouk, Asma [Qatar Environment and Energy Research Institute, Hamad Bin Khalifa University, P.O. Box 5825 Doha Qatar; Wang, Chongmin [Pacific Northwest National Laboratory, 902 Battelle Boulevard Richland WA 99354 USA; Xu, Guiliang [Chemical Sciences and Engineering Division, Argonne National Laboratory, 9700 South Cass Avenue Argonne IL 60439 USA; Chen, Zonghai [Chemical Sciences and Engineering Division, Argonne National Laboratory, 9700 South Cass Avenue Argonne IL 60439 USA; Amine, Khalil [Chemical Sciences and Engineering Division, Argonne National Laboratory, 9700 South Cass Avenue Argonne IL 60439 USA; Liu, Jun [Pacific Northwest National Laboratory, 902 Battelle Boulevard Richland WA 99354 USA; Sprenkle, Vincent L. [Pacific Northwest National Laboratory, 902 Battelle Boulevard Richland WA 99354 USA; El-Mellouhi, Fedwa [Qatar Environment and Energy Research Institute, Hamad Bin Khalifa University, P.O. Box 5825 Doha Qatar; Balbuena, Perla B. [Department of Chemical Engineering, Texas A& M University, College Station TX 77843-3122 USA; Li, Xiaolin [Pacific Northwest National Laboratory, 902 Battelle Boulevard Richland WA 99354 USA

    2017-03-07

    Solid-electrolyte interphase (SEI) with controllable properties are highly desirable to improve battery performance. In this paper, we use a combined experimental and simulation approach to study the SEI formation on hard carbon in Li and Na-ion batteries. We show that with proper additives, stable SEI can be formed on hard carbon by pre-cycling the electrode materials in Li or Na-ion electrolyte. Detailed mechanistic studies suggest that the ion transport in the SEI layer is kinetically controlled and can be tuned by the applied voltage. Selective Na and Li-ion SEI membranes are produced using the Na or Li-ion based electrolytes respectively. The large Na ion SEI allows easy transport of Li ions, while the small Li ion SEI shuts off the Na-ion transport. Na-ion storage can be manipulated by tuning the SEI with film-forming electrolyte additives or preforming a SEI on the electrodes’ surface. The Na specific capacity can be controlled to <25 mAh/g, ~1/10 of the normal capacity (250 mAh/g). Unusual selective/preferential transport of Li-ion is demonstrated by preforming a SEI on the electrode’s surface and corroborated with a mixed electrolyte. This work may provide new guidance for preparing good ion selective conductors using electrochemical approaches in the future.

  6. Tuning the Solid Electrolyte Interphase for Selective Li- and Na-Ion Storage in Hard Carbon

    Energy Technology Data Exchange (ETDEWEB)

    Soto, Fernando A. [Department of Chemical Engineering, Texas A& M University, College Station TX 77843-3122 USA; Yan, Pengfei [Pacific Northwest National Laboratory, 902 Battelle Boulevard Richland WA 99354 USA; Engelhard, Mark H. [Pacific Northwest National Laboratory, 902 Battelle Boulevard Richland WA 99354 USA; Marzouk, Asma [Qatar Environment and Energy Research Institute, Hamad Bin Khalifa University, P.O. Box 5825 Doha Qatar; Wang, Chongmin [Pacific Northwest National Laboratory, 902 Battelle Boulevard Richland WA 99354 USA; Xu, Guiliang [Chemical Sciences and Engineering Division, Argonne National Laboratory, 9700 South Cass Avenue Argonne IL 60439 USA; Chen, Zonghai [Chemical Sciences and Engineering Division, Argonne National Laboratory, 9700 South Cass Avenue Argonne IL 60439 USA; Amine, Khalil [Chemical Sciences and Engineering Division, Argonne National Laboratory, 9700 South Cass Avenue Argonne IL 60439 USA; Liu, Jun [Pacific Northwest National Laboratory, 902 Battelle Boulevard Richland WA 99354 USA; Sprenkle, Vincent L. [Pacific Northwest National Laboratory, 902 Battelle Boulevard Richland WA 99354 USA; El-Mellouhi, Fedwa [Qatar Environment and Energy Research Institute, Hamad Bin Khalifa University, P.O. Box 5825 Doha Qatar; Balbuena, Perla B. [Department of Chemical Engineering, Texas A& M University, College Station TX 77843-3122 USA; Li, Xiaolin [Pacific Northwest National Laboratory, 902 Battelle Boulevard Richland WA 99354 USA

    2017-03-07

    Solid-electrolyte interphase (SEI) films with controllable properties are highly desirable for improving battery performance. In this paper, a combined experimental and theoretical approach is used to study SEI films formed on hard carbon in Li- and Na-ion batteries. It is shown that a stable SEI layer can be designed by precycling an electrode in a desired Li- or Na-based electrolyte, and that ionic transport can be kinetically controlled. Selective Li- and Na-based SEI membranes are produced using Li- or Na-based electrolytes, respectively. The Na-based SEI allows easy transport of Li ions, while the Li-based SEI shuts off Na-ion transport. Na-ion storage can be manipulated by tuning the SEI layer with film-forming electrolyte additives, or by preforming an SEI layer on the electrode surface. The Na specific capacity can be controlled to < 25 mAh g(-1); approximate to 1/10 of the normal capacity (250 mAh g(-1)). Unusual selective/ preferential transport of Li ions is demonstrated by preforming an SEI layer on the electrode surface and corroborated with a mixed electrolyte. This work may provide new guidance for preparing good ion-selective conductors using electrochemical approaches.

  7. In Situ Chemical Imaging of Solid-Electrolyte Interphase Layer Evolution in Li–S Batteries

    Energy Technology Data Exchange (ETDEWEB)

    Nandasiri, Manjula I.; Camacho-Forero, Luis E.; Schwarz, Ashleigh M.; Shutthanandan, Vaithiyalingam; Thevuthasan, Suntharampillai; Balbuena, Perla B.; Mueller, Karl T.; Murugesan, Vijayakumar

    2017-05-16

    Parasitic reactions of electrolyte and polysulfide with the Li-anode in lithium sulfur (Li-S) batteries lead to the for-mation of solid electrolyte interphase (SEI) layers, which are the major reason behind severe capacity fading in these systems. Despite numerous studies, the evolution mechanism of the SEI layer and specific roles of polysulfides and oth-er electrolyte components are still unclear. We report an in-situ X-ray photoelectron spectroscopy (XPS) and chemical imaging analysis combined with ab initio molecular dynamics (AIMD) computational modeling to gain fundamental understanding regarding the evolution of SEI layers on Li-anodes within Li-S batteries. A multi-modal approach in-volving AIMD modeling and in-situ XPS characterization uniquely reveals the chemical identity and distribution of active participants in parasitic reactions as well as the SEI layer evolution mechanism. The SEI layer evolution has three major stages: the formation of a primary composite mixture phase involving stable lithium compounds (Li2S, LiF, Li2O etc); and formation of a secondary matrix type phase due to cross interaction between reaction products and elec-trolyte components, which is followed by a highly dynamic mono-anionic polysulfide (i.e. LiS5) fouling process. These new molecular-level insights into the SEI layer evolution on Li- anodes are crucial for delineating effective strategies for the development of Li–S batteries.

  8. Polymeric artificial solid/electrolyte interphases for Li-ion batteries

    Directory of Open Access Journals (Sweden)

    Nae-Lih Wu

    2015-12-01

    Full Text Available During the operation of Li-ion batteries (LIBs, solvent and electrolyte decomposition takes place at the electrode surface to form a so-called solid-electrode interphase (SEI passivating-layer. The physical structure and chemical composition of the SEI exert profound effects on various aspects of the electrode performance of the batteries. A new concept of forming polymeric artificial SEIs (A-SEIs based on rational design of multifunctional polymer-blend coating to achieve favorable electrode/A-SEI/electrolyte interfacial properties is described. Three examples using binary and ternary polymer blends to form mechanically robust and highly Li-ion permeable surface coatings with selected functionalities in the cases of graphite and silicon–graphite composite electrodes have demonstrated greatly enhanced capacity, rate and cycle performance. Given the rich chemistry available from polymer blends, this surface preconditioning approach holds great promise for improving the performance of various negative electrodes to meet the requirements for advanced LIBs.

  9. Quantifying lithium in the solid electrolyte interphase layer and beyond using Lithium- Nuclear Reaction Analysis technique

    Science.gov (United States)

    Schulz, Adam; Bakhru, Hassaram; DeRosa, Don; Higashiya, Seiichiro; Rane-Fondacaro, Manisha; Haldar, Pradeep

    2017-08-01

    Accurate knowledge of lithium content within the solid electrolyte interphase (SEI) layer and anode would significantly enhance the current understanding of the lithium ion battery (LIB) degradation mechanisms, enabling knowledge-based improvements in the technology. For the first time, we have demonstrated the capabilities of highly selective Lithium Nuclear Reaction Analysis (Li-NRA) as a non-destructive depth profiling technique for quantifying Li within the SEI and anode without accurate knowledge of the composition, which is unavailable with other depth profiling techniques. The Li-NRA technique detects the gamma radiation resulting from a nuclear reaction at characteristic resonance energy between an incident high-energy proton and Li. The intensity of γ-ray is directly proportional to the Li content, and the energy of the incident proton is increased stepwise to depth profile the sample. We performed Li-NRA on the carbonaceous negative electrodes of commercial LIB coin cells at varying states of charge (SOC) and states of health (SOH) conditions. We used three simple models for the composition of SEI and anode material to show concurrence between theoretical and experimental value for Li content at varying SOC conditions, estimated the average SEI layer thickness, and correlated the residual Li content within the SOH samples with electrochemical data.

  10. Wet Nanoindentation of the Solid Electrolyte Interphase on Thin Film Si Electrodes.

    Science.gov (United States)

    Kuznetsov, Volodymyr; Zinn, Arndt-Hendrik; Zampardi, Giorgia; Borhani-Haghighi, Sara; La Mantia, Fabio; Ludwig, Alfred; Schuhmann, Wolfgang; Ventosa, Edgar

    2015-10-28

    The solid electrolyte interphase (SEI) film formed at the surface of negative electrodes strongly affects the performance of a Li-ion battery. The mechanical properties of the SEI are of special importance for Si electrodes due to the large volumetric changes of Si upon (de)insertion of Li ions. This manuscript reports the careful determination of the Young's modulus of the SEI formed on a sputtered Si electrode using wet atomic force microscopy (AFM)-nanoindentation. Several key parameters in the determination of the Young's modulus are considered and discussed, e.g., wetness and roughness-thickness ratio of the film and the shape of a nanoindenter. The values of the Young's modulus were determined to be 0.5-10 MPa under the investigated conditions which are in the lower range of those previously reported, i.e., 1 MPa to 10 GPa, pointing out the importance of the conditions of its determination. After multiple electrochemical cycles, the polymeric deposits formed on the surface of the SEI are revealed, by force-volume mapping in liquid using colloidal probes, to extend up to 300 nm into bulk solution.

  11. Direct Visualization of Solid Electrolyte Interphase Formation in Lithium-Ion Batteries with In Situ Electrochemical Transmission Electron Microscopy

    Energy Technology Data Exchange (ETDEWEB)

    Unocic, Raymond R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Sun, Xiao-Guang [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Sacci, Robert L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Adamczyk, Leslie A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Alsem, Daan Hein [Hummingbird Scientific, Lacey, WA (United States); Dai, Sheng [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Dudney, Nancy J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); More, Karren Leslie [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2014-08-01

    Complex, electrochemically driven transport processes form the basis of electrochemical energy storage devices. The direct imaging of electrochemical processes at high spatial resolution and within their native liquid electrolyte would significantly enhance our understanding of device functionality, but has remained elusive. In this work we use a recently developed liquid cell for in situ electrochemical transmission electron microscopy to obtain insight into the electrolyte decomposition mechanisms and kinetics in lithium-ion (Li-ion) batteries by characterizing the dynamics of solid electrolyte interphase (SEI) formation and evolution. Here we are able to visualize the detailed structure of the SEI that forms locally at the electrode/electrolyte interface during lithium intercalation into natural graphite from an organic Li-ion battery electrolyte. We quantify the SEI growth kinetics and observe the dynamic self-healing nature of the SEI with changes in cell potential.

  12. Analytical investigations on the solid electrolyte interphase (SEI) film on graphite electrodes in lithium-ion batteries

    Energy Technology Data Exchange (ETDEWEB)

    Vetter, J.; Novak, P

    2003-03-01

    In order to investigate the organic decomposition products of the electrolyte forming the solid electrolyte interphase (SEI) on carbon electrodes in lithium-ion batteries, pre-cycled graphite electrodes were extracted. The extracts were analysed by gas chromatography (GC) and Fourier transform infrared spectroscopy (FTIR). A method for the separation of the compounds by high performance liquid chromatography (HPLC) was developed, and the SEI extracts were classified by comparison with reference substances. The results suggest that the SEI components have a molecular weight of several hundred mass units and a polyethylene oxide (PEO) like structure. (author)

  13. Organosulfide-plasticized solid-electrolyte interphase layer enables stable lithium metal anodes for long-cycle lithium-sulfur batteries.

    Science.gov (United States)

    Li, Guoxing; Gao, Yue; He, Xin; Huang, Qingquan; Chen, Shuru; Kim, Seong H; Wang, Donghai

    2017-10-11

    Lithium metal is a promising anode candidate for the next-generation rechargeable battery due to its highest specific capacity (3860 mA h g-1) and lowest potential, but low Coulombic efficiency and formation of lithium dendrites hinder its practical application. Here, we report a self-formed flexible hybrid solid-electrolyte interphase layer through co-deposition of organosulfides/organopolysulfides and inorganic lithium salts using sulfur-containing polymers as an additive in the electrolyte. The organosulfides/organopolysulfides serve as "plasticizer" in the solid-electrolyte interphase layer to improve its mechanical flexibility and toughness. The as-formed robust solid-electrolyte interphase layers enable dendrite-free lithium deposition and significantly improve Coulombic efficiency (99% over 400 cycles at a current density of 2 mA cm-2). A lithium-sulfur battery based on this strategy exhibits long cycling life (1000 cycles) and good capacity retention. This study reveals an avenue to effectively fabricate stable solid-electrolyte interphase layer for solving the issues associated with lithium metal anodes.The practical application of lithium metal anodes suffers from the poor Coulombic efficiency and growth of lithium dendrites. Here, the authors report an approach to enable the self-formation of stable and flexible solid-electrolyte interphase layers which serve to address both issues.

  14. In Situ Mass Spectrometric Determination of Molecular Structural Evolution at the Solid Electrolyte Interphase in Lithium-Ion Batteries.

    Science.gov (United States)

    Zhu, Zihua; Zhou, Yufan; Yan, Pengfei; Vemuri, Rama Sesha; Xu, Wu; Zhao, Rui; Wang, Xuelin; Thevuthasan, Suntharampillai; Baer, Donald R; Wang, Chong-Min

    2015-09-09

    Dynamic structural and chemical evolution at solid-liquid electrolyte interface is always a mystery for a rechargeable battery due to the challenge to directly probe a solid-liquid interface under reaction conditions. We describe the creation and usage of in situ liquid secondary ion mass spectroscopy (SIMS) for the first time to directly observe the molecular structural evolution at the solid-liquid electrolyte interface for a lithium (Li)-ion battery under dynamic operating conditions. We have discovered that the deposition of Li metal on copper electrode leads to the condensation of solvent molecules around the electrode. Chemically, this layer of solvent condensate tends to be depleted of the salt anions and with reduced concentration of Li(+) ions, essentially leading to the formation of a lean electrolyte layer adjacent to the electrode and therefore contributing to the overpotential of the cell. This observation provides unprecedented molecular level dynamic information on the initial formation of the solid electrolyte interphase (SEI) layer. The present work also ultimately opens new avenues for implanting the in situ liquid SIMS concept to probe the chemical reaction process that intimately involves solid-liquid interface, such as electrocatalysis, electrodeposition, biofuel conversion, biofilm, and biomineralization.

  15. Direct observation of inhomogeneous solid electrolyte interphase on MnO anode with atomic force microscopy and spectroscopy.

    Science.gov (United States)

    Zhang, Jie; Wang, Rui; Yang, Xiaocheng; Lu, Wei; Wu, Xiaodong; Wang, Xiaoping; Li, Hong; Chen, Liwei

    2012-04-11

    Solid electrolyte interphase (SEI) is an in situ formed thin coating on lithium ion battery (LIB) electrodes. The mechanical property of SEI largely defines the cycling performance and the safety of LIBs but has been rarely investigated. Here, we report quantitatively the Young's modulus of SEI films on MnO anodes. The inhomogeneity of SEI film in morphology, structure, and mechanical properties provides new insights to the evolution of SEI on electrodes. Furthermore, the quantitative methodology established in this study opens a new approach to direct investigation of SEI properties in various electrode materials systems. © 2012 American Chemical Society

  16. Artificially-built solid electrolyte interphase via surface-bonded vinylene carbonate derivative on graphite by molecular layer deposition

    Science.gov (United States)

    Chae, Seulki; Lee, Jeong Beom; Lee, Jae Gil; Lee, Tae-jin; Soon, Jiyong; Ryu, Ji Heon; Lee, Jin Seok; Oh, Seung M.

    2017-12-01

    Vinylene carbonate (VC) is attached in a ring-opened form on a graphite surface by molecular layer deposition (MLD) method, and its role as a solid electrolyte interphase (SEI) former is studied. When VC is added into the electrolyte solution of a graphite/LiNi0.5Mn1.5O4 (LNMO) full-cell, it is reductively decomposed to form an effective SEI on the graphite electrode. However, VC in the electrolyte solution has serious adverse effects due to its poor stability against electrochemical oxidation on the LNMO positive electrode. A excessive acid generation as a result of VC oxidation is observed, causing metal dissolution from the LNMO electrode. The dissolved metal ions are plated on the graphite electrode to destroy the SEI layer, eventually causing serious capacity fading and poor Coulombic efficiency. The VC derivative on the graphite surface also forms an effective SEI layer on the graphite negative electrode via reductive decomposition. The detrimental effects on the LNMO positive electrode, however, can be avoided because the bonded VC derivative on the graphite surface cannot move to the LNMO electrode. Consequently, the graphite/LNMO full-cell fabricated with the VC-attached graphite outperforms the cells without VC or with VC in the electrolyte, in terms of Coulombic efficiency and capacity retention.

  17. Single nanowire electrode electrochemistry of silicon anode by in situ atomic force microscopy: solid electrolyte interphase growth and mechanical properties.

    Science.gov (United States)

    Liu, Xing-Rui; Deng, Xin; Liu, Ran-Ran; Yan, Hui-Juan; Guo, Yu-Guo; Wang, Dong; Wan, Li-Jun

    2014-11-26

    Silicon nanowires (SiNWs) have attracted great attention as promising anode materials for lithium ion batteries (LIBs) on account of their high capacity and improved cyclability compared with bulk silicon. The interface behavior, especially the solid electrolyte interphase (SEI), plays a significant role in the performance and stability of the electrodes. We report herein an in situ single nanowire atomic force microscopy (AFM) method to investigate the interface electrochemistry of silicon nanowire (SiNW) electrode. The morphology and Young's modulus of the individual SiNW anode surface during the SEI growth were quantitatively tracked. Three distinct stages of the SEI formation on the SiNW anode were observed. On the basis of the potential-dependent morphology and Young's modulus evolution of SEI, a mixture-packing structural model was proposed for the SEI film on SiNW anode.

  18. New Insights of Graphite Anode Stability in Rechargeable Batteries: Li-Ion Coordination Structures Prevail over Solid Electrolyte Interphases

    KAUST Repository

    Ming, Jun

    2018-01-04

    Graphite anodes are not stable in most noncarbonate solvents (e.g., ether, sulfoxide, sulfone) upon Li ion intercalation, known as an urgent issue in present Li ions and next-generation Li–S and Li–O2 batteries for storage of Li ions within the anode for safety features. The solid electrolyte interphase (SEI) is commonly believed to be decisive for stabilizing the graphite anode. However, here we find that the solvation structure of the Li ions, determined by the electrolyte composition including lithium salts, solvents, and additives, plays a more dominant role than SEI in graphite anode stability. The Li ion intercalation desired for battery operation competes with the undesired Li+–solvent co-insertion, leading to graphite exfoliation. The increase in organic lithium salt LiN(SO2CF3)2 concentration or, more effectively, the addition of LiNO3 lowers the interaction strength between Li+ and solvents, suppressing the graphite exfoliation caused by Li+–solvent co-insertion. Our findings refresh the knowledge of the well-known SEI for graphite stability in metal ion batteries and also provide new guidelines for electrolyte systems to achieve reliable and safe Li–S full batteries.

  19. Surface chemistry and morphology of the solid electrolyte interphase on silicon nanowire lithium-ion battery anodes

    KAUST Repository

    Chan, Candace K.

    2009-04-01

    Silicon nanowires (SiNWs) have the potential to perform as anodes for lithium-ion batteries with a much higher energy density than graphite. However, there has been little work in understanding the surface chemistry of the solid electrolyte interphase (SEI) formed on silicon due to the reduction of the electrolyte. Given that a good, passivating SEI layer plays such a crucial role in graphite anodes, we have characterized the surface composition and morphology of the SEI formed on the SiNWs using X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). We have found that the SEI is composed of reduction products similar to that found on graphite electrodes, with Li2CO3 as an important component. Combined with electrochemical impedance spectroscopy, the results were used to determine the optimal cycling parameters for good cycling. The role of the native SiO2 as well as the effect of the surface area of the SiNWs on reactivity with the electrolyte were also addressed. © 2009 Elsevier B.V. All rights reserved.

  20. New Insights on the Structure of Electrochemically Deposited Lithium Metal and Its Solid Electrolyte Interphases via Cryogenic TEM

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Xuefeng; Zhang, Minghao; Alvarado, Judith; Wang, Shen; Sina, Mahsa; Lu, Bingyu; Bouwer, James; Xu, Wu [Energy; Xiao, Jie [Energy; Zhang, Ji-Guang [Energy; Liu, Jun [Energy; Meng, Ying Shirley

    2017-11-02

    Lithium metal has been considered as the “holy grail” anode material for rechargeable batteries though the dendritic growth and low Coulombic efficiency (CE) have crippled its practical use for decades. Its high chemical reactivity and low stability make it difficult to explore the intrinsic chemical and physical properties of the electrochemically deposited lithium (EDLi) and its accompanied solid electrolyte interphase (SEI). To prevent the dendritic growth and enhance the electrochemical reversibility, it is crucial to understand the nano- and meso- structures of EDLi. However, Li metal is very sensitive to beam damage and has low contrast for commonly used characterization techniques such as electron microscopy. Inspired by biological imaging techniques, this work demonstrates the power of cryogenic (cryo)- electron microscopy to reveal the detailed structure of EDLi and the SEI composition at the nano scale while minimizing beam damage during imaging. Surprisingly, the results show that the nucleation dominated EDLi (five minutes at 0.5 mA cm-2) is amorphous while there is some crystalline LiF present in the SEI. The EDLi grown from various electrolytes with different additives exhibits distinctive surface properties. Consequently, these results highlight the importance of the SEI and its relationship with the CE. Our findings not only illustrate the capabilities of cryogenic microscopy for beam (thermal)-sensitive materials, but it yields crucial structural information of the EDLi evolution with and without electrolyte additives.

  1. New Insights on the Structure of Electrochemically Deposited Lithium Metal and Its Solid Electrolyte Interphases via Cryogenic TEM.

    Science.gov (United States)

    Wang, Xuefeng; Zhang, Minghao; Alvarado, Judith; Wang, Shen; Sina, Mahsa; Lu, Bingyu; Bouwer, James; Xu, Wu; Xiao, Jie; Zhang, Ji-Guang; Liu, Jun; Meng, Ying Shirley

    2017-12-13

    Lithium metal has been considered the "holy grail" anode material for rechargeable batteries despite the fact that its dendritic growth and low Coulombic efficiency (CE) have crippled its practical use for decades. Its high chemical reactivity and low stability make it difficult to explore the intrinsic chemical and physical properties of the electrochemically deposited lithium (EDLi) and its accompanying solid electrolyte interphase (SEI). To prevent the dendritic growth and enhance the electrochemical reversibility, it is crucial to understand the nano- and mesostructures of EDLi. However, Li metal is very sensitive to beam damage and has low contrast for commonly used characterization techniques such as electron microscopy. Inspired by biological imaging techniques, this work demonstrates the power of cryogenic (cryo)-electron microscopy to reveal the detailed structure of EDLi and the SEI composition at the nanoscale while minimizing beam damage during imaging. Surprisingly, the results show that the nucleation-dominated EDLi (5 min at 0.5 mA cm -2 ) is amorphous, while there is some crystalline LiF present in the SEI. The EDLi grown from various electrolytes with different additives exhibits distinctive surface properties. Consequently, these results highlight the importance of the SEI and its relationship with the CE. Our findings not only illustrate the capabilities of cryogenic microscopy for beam (thermal)-sensitive materials but also yield crucial structural information on the EDLi evolution with and without electrolyte additives.

  2. Methods for solid electrolyte interphase formation and anode pre-lithiation of lithium ion capacitors

    Energy Technology Data Exchange (ETDEWEB)

    Raman, Santhanam; Xi, Xiaomei; Ye, Xiang-Rong

    2017-07-18

    A method of pre-doping an anode of an energy storage device can include immersing the anode and a dopant source in an electrolyte, and coupling a substantially constant current between the anode and the dopant source. A method of pre-doping an anode of an energy storage device can include immersing the anode and a dopant source in an electrolyte, and coupling a substantially constant voltage across the anode and the dopant source. An energy storage device can include an anode having a lithium ion pre-doping level of about 60% to about 90%.

  3. Designing Artificial Solid-Electrolyte Interphases for Single-Ion and High-Efficiency Transport in Batteries

    KAUST Repository

    Tu, Zhengyuan

    2017-09-21

    Substrates able to rectify transport of ions based on charge and/or size are ubiquitous in biological systems. Electrolytes and interphases that selectively transport electrochemically active ions are likewise of broad interest in all electrical energy storage technologies. In lithium-ion batteries, electrolytes with single- or near-single-ion conductivity reduce losses caused by ion polarization. In emergent lithium or sodium metal batteries, they maintain high conductivity at the anode and stabilize metal deposition by fundamental mechanisms. We report that 20- to 300-nm-thick, single-ion-conducting membranes deposited at the anode enable electrolytes with the highest combination of cation transference number, ionic conductivity, and electrochemical stability reported. By means of direct visualization we find that single-ion membranes also reduce dendritic deposition of Li in liquids. Galvanostatic measurements further show that the electrolytes facilitate long (3 mAh) recharge of full Li/LiNi0.8Co0.15Al0.05O2 (NCA) cells with high cathode loadings (3 mAh cm−2/19.9 mg cm−2) and at high current densities (3 mA cm−2).

  4. Solid electrolytes

    Science.gov (United States)

    Abraham, Kuzhikalail M.; Alamgir, Mohamed

    1993-06-15

    This invention pertains to Li ion (Li.sup.+) conductive solid polymer electrolytes composed of solvates of Li salts immobilized (encapsulated) in a solid organic polymer matrix. In particular, this invention relates to solid polymer electrolytes derived by immobilizing complexes (solvates) formed between a Li salt such as LiAsF.sub.6, LiCF.sub.3 SO.sub.3 or LiClO.sub.4 and a mixture of aprotic organic solvents having high dielectric constants such as ethylene carbonate (EC) (dielectric constant=89.6) and propylene carbonate (PC) (dielectric constant=64.4) in a polymer matrix such as polyacrylonitrile, poly(tetraethylene glycol diacrylate), or poly(vinyl pyrrolidinone).

  5. Dual-Phase Lithium Metal Anode Containing a Polysulfide-Induced Solid Electrolyte Interphase and Nanostructured Graphene Framework for Lithium-Sulfur Batteries.

    Science.gov (United States)

    Cheng, Xin-Bing; Peng, Hong-Jie; Huang, Jia-Qi; Zhang, Rui; Zhao, Chen-Zi; Zhang, Qiang

    2015-06-23

    Lithium-sulfur (Li-S) batteries, with a theoretical energy density of 2600 Wh kg(-1), are a promising platform for high-energy and cost-effective electrochemical energy storage. However, great challenges such as fast capacity degradation and safety concerns prevent it from widespread application. With the adoption of Li metal as the anode, dendritic and mossy metal depositing on the negative electrode during repeated cycles leads to serious safety concerns and low Coulombic efficiency. Herein, we report a distinctive graphene framework structure coated by an in situ formed solid electrolyte interphase (SEI) with Li depositing in the pores as the anode of Li-S batteries. The graphene-based metal anode demonstated a superior dendrite-inhibition behavior in 70 h of lithiation, while the cell with a Cu foil based metal anode was short-circuited after only 4 h of lithiation at 0.5 mA cm(-2). The graphene-modified Li anode with SEI induced by the polysulfide-containing electrolyte improved the Coulombic efficiency to ∼97% for more than 100 cycles, while the control sample with Cu foil as the current collector exhibited huge fluctuations in Coulombic efficiency. The unblocked ion pathways and high electron conductivities of frameworks in the modified metal anode led to the rapid transfer of Li ions through the SEI and endowed the anode framework with an ion conductivity of 7.81 × 10(-2) mS cm(-1), nearly quintuple that of the Cu foil based Li metal anode. Besides, the polarization in the charge-discharge process was halved to 30 mV. The stable and efficient Li deposition was maintained after 2000 cycles. Our results indicated that nanoscale interfacial electrode engineering could be a promising strategy to tackle the intrinsic problems of lithium metal anodes, thus improving the safety of Li-S cells.

  6. Depth profiling the solid electrolyte interphase on lithium titanate (Li4Ti5O12) using synchrotron-based photoelectron spectroscopy

    DEFF Research Database (Denmark)

    Nordh, Tim; Younesi, Reza; Brandell, Daniel

    2015-01-01

    The presence of a surface layer on lithium titanate (Li4Ti5O12, LTO) anodes, which has been a topic of debate in scientific literature, is here investigated with tunable high surface sensitive synchrotron-based photoelectron spectroscopy (PES) to obtain a reliable depth profile of the interphase....... electrode as such, and an electrode soaked in the electrolyte were analyzed by varying the photon energies enabling depth profiling of the outermost surface layer. The main components of the surface layer were found to be ethers, P-O containing compounds, and lithium fluoride....

  7. Reduction mechanism of fluoroethylene carbonate for stable solid–electrolyte interphase film on silicon anode.

    Science.gov (United States)

    Chen, Xilin; Li, Xiaolin; Mei, Donghai; Feng, Ju; Hu, Mary Y; Hu, Jianzhi; Engelhard, Mark; Zheng, Jianming; Xu, Wu; Xiao, Jie; Liu, Jun; Zhang, Ji-Guang

    2014-02-01

    Fluoroethylene carbonate (FEC) is an effective electrolyte additive that can significantly improve the cycling ability of silicon and other anode materials. However, the fundamental mechanism of this improvement is still not well understood. Based on the results obtained from (6)Li NMR and X-ray photoelectron spectroscopy studies, we propose a molecular-level mechanism for how FEC affects the formation of solid electrolyte interphase (SEI) film: 1) FEC is reduced through the opening of the five-membered ring leading to the formation of lithium poly(vinyl carbonate), LiF, and some dimers; 2) the FEC-derived lithium poly(vinyl carbonate) enhances the stability of the SEI film. The proposed reduction mechanism opens a new path to explore new electrolyte additives that can improve the cycling stability of silicon-based electrodes.

  8. Stable cycling of double-walled silicon nanotube battery anodes through solid–electrolyte interphase control

    KAUST Repository

    Wu, Hui

    2012-03-25

    Although the performance of lithium ion-batteries continues to improve, their energy density and cycle life remain insufficient for applications in consumer electronics, transport and large-scale renewable energy storage 1-5. Silicon has a large charge storage capacity and this makes it an attractive anode material, but pulverization during cycling and an unstable solid-electrolyte interphase has limited the cycle life of silicon anodes to hundreds of cycles 6-11. Here, we show that anodes consisting of an active silicon nanotube surrounded by an ion-permeable silicon oxide shell can cycle over 6,000 times in half cells while retaining more than 85% of their initial capacity. The outer surface of the silicon nanotube is prevented from expansion by the oxide shell, and the expanding inner surface is not exposed to the electrolyte, resulting in a stable solid-electrolyte interphase. Batteries containing these double-walled silicon nanotube anodes exhibit charge capacities approximately eight times larger than conventional carbon anodes and charging rates of up to 20C (a rate of 1C corresponds to complete charge or discharge in one hour). © 2012 Macmillan Publishers Limited. All rights reserved.

  9. Solid Electrolyte Interphase (SEI) at TiO2 Electrodes in Li-Ion Batteries: Defining Apparent and Effective SEI Based on Evidence from X-ray Photoemission Spectroscopy and Scanning Electrochemical Microscopy.

    Science.gov (United States)

    Ventosa, Edgar; Madej, Edyta; Zampardi, Giorgia; Mei, Bastian; Weide, Philipp; Antoni, Hendrik; La Mantia, Fabio; Muhler, Martin; Schuhmann, Wolfgang

    2017-01-25

    The high (de)lithiation potential of TiO2 (ca. 1.7 V vs Li/Li+ in 1 M Li+) decreases the voltage and, thus, the energy density of a corresponding Li-ion battery. On the other hand, it offers several advantages such as the (de)lithiation potential far from lithium deposition or absence of a solid electrolyte interphase (SEI). The latter is currently under controversial debate as several studies reported the presence of a SEI when operating TiO2 electrodes at potentials above 1.0 V vs Li/Li+. We investigate the formation of a SEI at anatase TiO2 electrodes by means of X-ray photoemission spectroscopy (XPS) and scanning electrochemical microscopy (SECM). The investigations were performed in different potential ranges, namely, during storage (without external polarization), between 3.0-2.0 V and 3.0-1.0 V vs Li/Li+, respectively. No SEI is formed when a completely dried and residues-free TiO2 electrode is cycled between 3.0 and 2.0 V vs Li/Li+. A SEI is detected by XPS in the case of samples stored for 6 weeks or cycled between 3.0 and 1.0 V vs Li/Li+. With use of SECM, it is verified that this SEI does not possess the electrically insulating character as expected for a "classic" SEI. Therefore, we propose the term apparent SEI for TiO2 electrodes to differentiate it from the protecting and effective SEI formed at graphite electrodes.

  10. Solid polymer electrolytes

    Science.gov (United States)

    Abraham, Kuzhikalail M.; Alamgir, Mohamed; Choe, Hyoun S.

    1995-01-01

    This invention relates to Li ion (Li.sup.+) conductive solid polymer electrolytes composed of poly(vinyl sulfone) and lithium salts, and their use in all-solid-state rechargeable lithium ion batteries. The lithium salts comprise low lattice energy lithium salts such as LiN(CF.sub.3 SO.sub.2).sub.2, LiAsF.sub.6, and LiClO.sub.4.

  11. Designing solid-liquid interphases for sodium batteries

    KAUST Repository

    Choudhury, Snehashis

    2017-10-06

    Secondary batteries based on earth-abundant sodium metal anodes are desirable for both stationary and portable electrical energy storage. Room-temperature sodium metal batteries are impractical today because morphological instability during recharge drives rough, dendritic electrodeposition. Chemical instability of liquid electrolytes also leads to premature cell failure as a result of parasitic reactions with the anode. Here we use joint density-functional theoretical analysis to show that the surface diffusion barrier for sodium ion transport is a sensitive function of the chemistry of solid–electrolyte interphase. In particular, we find that a sodium bromide interphase presents an exceptionally low energy barrier to ion transport, comparable to that of metallic magnesium. We evaluate this prediction by means of electrochemical measurements and direct visualization studies. These experiments reveal an approximately three-fold reduction in activation energy for ion transport at a sodium bromide interphase. Direct visualization of sodium electrodeposition confirms large improvements in stability of sodium deposition at sodium bromide-rich interphases.

  12. Sulfonate-immobilized artificial cathode electrolyte interphases layer on Ni-rich cathode

    Science.gov (United States)

    Chae, Bum-Jin; Yim, Taeeun

    2017-08-01

    Although lithium nickel cobalt manganese layered oxides with a high nickel composition have gained great attention due to increased overall energy density for energy conversion/storage systems, poor interfacial stability is considered a critical bottleneck impeding its widespread adoption. We propose a new approach based on immobilizing the artificial cathode-electrolyte interphase layer, which effectively reduces undesired surface reactions, leading to high interfacial stability of cathode material. For installation of artificial cathode-electrolyte interphases, a sulfonate-based amphiphilic organic precursor, which effectively suppresses electrolyte decomposition, is synthesized and subjected to immobilization on cathode material via simple wet-coating, followed by heat treatment at low temperature. The sulfonate-based artificial cathode-electrolyte interphase layer is well-developed on the cathode surface, and the cell controlled by the sulfonate-immobilized cathode exhibits remarkable electrochemical performance, including a high average Coulombic efficiency (99.8%) and cycling retention (97.4%) compared with pristine cathode material. The spectroscopic analyses of the cycled cathode show that the sulfonate-based artificial cathode-electrolyte interphase layer effectively mitigates electrolyte decomposition on the cathode surface, resulting in decreased interfacial resistance between electrode and electrolyte.

  13. Solid state electrolyte systems

    Energy Technology Data Exchange (ETDEWEB)

    Pederson, L.R.; Armstrong, B.L.; Armstrong, T.R. [Pacific Northwest Lab., Richland, WA (United States)] [and others

    1997-12-01

    Lanthanum gallates are a new family of solid electrolytes that exhibit high ionic conductivity and are stable to high temperatures. Compositions have been developed that are as much as a factor of two more conductive than yttria-stabilized zirconia at a given temperature, through partial replacement of lanthanum by calcium, strontium, and/or barium and through partial replacement of gallium by magnesium. Oxide powders were prepared using combustion synthesis techniques developed in this laboratory; these were sintered to >95% of theoretical density and consisted of a single crystalline phase. Electrical conductivities, electron and ion transference numbers, thermal expansion, and phase behavior were evaluated as a function of temperature and oxygen partial pressure. A key advantage of the use of lanthanum gallate electrolytes in solid oxide fuel cells is that the temperature of operation may be lowered to perhaps 800 C, yet provide approximately the same power density as zirconia-based cells operating at 1000 C. Ceramic electrolytes that conduct both oxygen ions and electrons are potentially useful to passively separate pure oxygen from an air source at low cost. In such materials, an oxygen ion flux in one direction is charge-compensated by an opposing electron flux. The authors have examined a wide range of mixed ion and electron conducting perovskite ceramics in the system La{sub 1{minus}x}M{sub x}Co{sub 1{minus}y{minus}z}Fe{sub y}N{sub z}O{sub 3{minus}{delta}}, where M = Sr, Ca, and Ba, and N = Pr, Mn, Ni, Cu, Ti, and Al, as well as mixed conducting brownmillerite ceramics, and have characterized oxygen permeation behavior, defect chemistry, structural and phase stability, and performance as cathodes.

  14. Solid polymer electrolyte lithium batteries

    Science.gov (United States)

    Alamgir, Mohamed; Abraham, Kuzhikalail M.

    1993-01-01

    This invention pertains to Lithium batteries using Li ion (Li.sup.+) conductive solid polymer electrolytes composed of solvates of Li salts immobilized in a solid organic polymer matrix. In particular, this invention relates to Li batteries using solid polymer electrolytes derived by immobilizing solvates formed between a Li salt and an aprotic organic solvent (or mixture of such solvents) in poly(vinyl chloride).

  15. Composite solid polymer electrolyte membranes

    Science.gov (United States)

    Formato, Richard M.; Kovar, Robert F.; Osenar, Paul; Landrau, Nelson; Rubin, Leslie S.

    2006-05-30

    The present invention relates to composite solid polymer electrolyte membranes (SPEMs) which include a porous polymer substrate interpenetrated with an ion-conducting material. SPEMs of the present invention are useful in electrochemical applications, including fuel cells and electrodialysis.

  16. Composite solid polymer electrolyte membranes

    Science.gov (United States)

    Formato, Richard M.; Kovar, Robert F.; Osenar, Paul; Landrau, Nelson; Rubin, Leslie S.

    2001-06-19

    The present invention relates to composite solid polymer electrolyte membranes (SPEMs) which include a porous polymer substrate interpenetrated with an ion-conducting material. SPEMs of the present invention are useful in electrochemical applications, including fuel cells and electrodialysis.

  17. Electrolyte for batteries with regenerative solid electrolyte interface

    Energy Technology Data Exchange (ETDEWEB)

    Xiao, Jie; Lu, Dongping; Shao, Yuyan; Bennett, Wendy D.; Graff, Gordon L.; Liu, Jun; Zhang, Ji-Guang

    2017-08-01

    An energy storage device comprising: an anode; and a solute-containing electrolyte composition wherein the solute concentration in the electrolyte composition is sufficiently high to form a regenerative solid electrolyte interface layer on a surface of the anode only during charging of the energy storage device, wherein the regenerative layer comprises at least one solute or solvated solute from the electrolyte composition.

  18. Antireduction Insulator For Solid-Electrolyte Cell

    Science.gov (United States)

    Shlichta, Paul J.

    1990-01-01

    Depletion of oxygen from electrolyte prevented. Proposed to add layer of electrical insulation between solid electrolyte and portion of porous negative electrode under negative metal contact in solid-electrolyte cell. Helps maintain efficiency of cell by preventing "shadow" effect degrading portion of electrolyte under negative contact and sometimes near seals.

  19. Rechargeable solid polymer electrolyte battery cell

    Science.gov (United States)

    Skotheim, Terji

    1985-01-01

    A rechargeable battery cell comprising first and second electrodes sandwiching a solid polymer electrolyte comprising a layer of a polymer blend of a highly conductive polymer and a solid polymer electrolyte adjacent said polymer blend and a layer of dry solid polymer electrolyte adjacent said layer of polymer blend and said second electrode.

  20. Solid electrolytes general principles, characterization, materials, applications

    CERN Document Server

    Hagenmuller, Paul

    1978-01-01

    Solid Electrolytes: General Principles, Characterization, Materials, Applications presents specific theories and experimental methods in the field of superionic conductors. It discusses that high ionic conductivity in solids requires specific structural and energetic conditions. It addresses the problems involved in the study and use of solid electrolytes. Some of the topics covered in the book are the introduction to the theory of solid electrolytes; macroscopic evidence for liquid nature; structural models; kinetic models; crystal structures and fast ionic conduction; interstitial motion in

  1. Solid State Multinuclear Magnetic Resonance Investigation of Electrolyte Decomposition Products on Lithium Ion Electrodes

    Science.gov (United States)

    DeSilva, J .H. S. R.; Udinwe, V.; Sideris, P. J.; Smart, M. C.; Krause, F. C.; Hwang, C.; Smith, K. A.; Greenbaum, S. G.

    2012-01-01

    Solid electrolyte interphase (SEI) formation in lithium ion cells prepared with advanced electrolytes is investigated by solid state multinuclear (7Li, 19F, 31P) magnetic resonance (NMR) measurements of electrode materials harvested from cycled cells subjected to an accelerated aging protocol. The electrolyte composition is varied to include the addition of fluorinated carbonates and triphenyl phosphate (TPP, a flame retardant). In addition to species associated with LiPF6 decomposition, cathode NMR spectra are characterized by the presence of compounds originating from the TPP additive. Substantial amounts of LiF are observed in the anodes as well as compounds originating from the fluorinated carbonates.

  2. Anode-originated SEI migration contributes to formation of cathode-electrolyte interphase layer

    Science.gov (United States)

    Fang, Shuyu; Jackson, David; Dreibelbis, Mark L.; Kuech, Thomas F.; Hamers, Robert J.

    2018-01-01

    Cathode-electrolyte interphase (CEI) formation is a key process that impacts the performance of lithium-ion batteries. In this work, we characterized the composition and stoichiometry of CEI layer on LiNixMnyCo1-x-yO2 (NMC) cathodes via a novel combination of quantitative correlation analysis of X-ray photoelectron spectra and binder-free cathode formulation. By comparing the CEI formation in NMC-based cells with lithium, graphite and lithium titanate anodes, we demonstrate a CEI formation pathway via migration of surface species that originally formed on the anode side. A case study of cathodes coated by atomic layer deposition with a thin layer of Al2O3 demonstrates that anode-to-cathode migration can be mitigated by ALD cathode coatings. This work highlights the importance of anode-mediated processes in order to correctly interpret surface phenomena on the cathode side and to guide further development of surface protection strategies.

  3. Electrode-Electrolyte Interfaces in Lithium-Sulfur Batteries with Liquid or Inorganic Solid Electrolytes.

    Science.gov (United States)

    Yu, Xingwen; Manthiram, Arumugam

    2017-11-21

    Electrode-electrolyte interfacial properties play a vital role in the cycling performance of lithium-sulfur (Li-S) batteries. The issues at an electrode-electrolyte interface include electrochemical and chemical reactions occurring at the interface, formation mechanism of interfacial layers, compositional/structural characteristics of the interfacial layers, ionic transport across the interface, and thermodynamic and kinetic behaviors at the interface. Understanding the above critical issues is paramount for the development of strategies to enhance the overall performance of Li-S batteries. Liquid electrolytes commonly used in Li-S batteries bear resemblance to those employed in traditional lithium-ion batteries, which are generally composed of a lithium salt dissolved in a solvent matrix. However, due to a series of unique features associated with sulfur or polysulfides, ether-based solvents are generally employed in Li-S batteries rather than simply adopting the carbonate-type solvents that are generally used in the traditional Li+-ion batteries. In addition, the electrolytes of Li-S batteries usually comprise an important additive, LiNO3. The unique electrolyte components of Li-S batteries do not allow us to directly take the interfacial theories of the traditional Li+-ion batteries and apply them to Li-S batteries. On the other hand, during charging/discharging a Li-S battery, the dissolved polysulfide species migrate through the battery separator and react with the Li anode, which magnifies the complexity of the interfacial problems of Li-S batteries. However, current Li-S battery development paths have primarily been energized by advances in sulfur cathodes. Insight into the electrode-electrolyte interfacial behaviors has relatively been overshadowed. In this Account, we first examine the state-of-the-art contributions in understanding the solid-electrolyte interphase (SEI) formed on the Li-metal anode and sulfur cathode in conventional liquid-electrolyte Li

  4. Solid electrolyte interphase (SEI) at TiO2 electrodes in li-ion batteries : Defining apparent and effective SEI based on evidence from X-ay photoemission spectroscopy and scanning electrochemical microscopy

    NARCIS (Netherlands)

    Ventosa, Edgar; Madej, Edyta; Zampardi, Giorgia; Mei, Bastian; Weide, Philipp; Antoni, Hendrik; La Mantia, Fabio; Muhler, Martin; Schuhmann, Wolfgang

    2017-01-01

    The high (de)lithiation potential of TiO2 (ca. 1.7 V vs Li/ Li+ in 1 M Li+) decreases the voltage and, thus, the energy density of a corresponding Li-ion battery. On the other hand, it offers several advantages such as the (de)lithiation potential far from lithium deposition or absence of a solid

  5. Response behaviour of oxygen sensing solid electrolytes

    NARCIS (Netherlands)

    Winnubst, Aloysius J.A.; Scharenborg, A.H.A.; Burggraaf, A.J.

    1985-01-01

    The response time (t r) after a step change in oxygen partial pressure was investigated for some solid electrolytes used in Nernst type oxygen sensors. The electrolyte as well as the (porous) electrode material affect the value oft r. Stabilized Bi2O3 materials exhibit slower response rates (largert

  6. On the interfacial charge transfer between solid and liquid Li(+) electrolytes.

    Science.gov (United States)

    Schleutker, Marco; Bahner, Jochen; Tsai, Chih-Long; Stolten, Detlef; Korte, Carsten

    2017-10-11

    The Li(+) ion transfer between a solid and a liquid Li(+) electrolyte has been investigated by DC polarisation techniques. The current density i is measured as a function of the electrochemical potential drop Δ[small mu, Greek, tilde]Li(+) at the interface, using a liquid electrolyte with different Li(+) concentrations. The subject of this experimental study is the interface between the solid electrolyte Ta-substituted lithium lanthanum zirconate (Li6.6La3Zr1.6Ta0.4O12) and a liquid electrolyte consisting of LiPF6 dissolved in ethylene carbonate/dimethyl carbonate (1 : 1). The functional course of i vs. Δ[small mu, Greek, tilde]Li(+) can be described by a serial connection between a constant ohmic resistance Rslei and a current dependent thermally activated ion transfer process. For the present solid-liquid electrolyte interface the areal resistance Rslei of the surface layer is independent of the Li(+) concentration in the liquid electrolyte. At room temperature a value of about 300 Ω cm(2) is found. The constant ohmic resistance Rslei can be attributed to a surface layer on the solid electrolyte with a (relatively) low conductivity (solid-liquid electrolyte interphase). The low conducting surface layer is formed by degradation reactions with the liquid electrolyte. Rslei is considerably increased if a small amount (ppm) of water is added to the liquid electrolyte. The thermally activated ionic transfer process obeys a Butler-Volmer like behaviour, resulting in an exchange current density i0 depending on the Li(+) concentration in the liquid electrolyte by a power-law. At a Li(+) concentration of 1 mol l(-1) a value of 53.1 μA cm(-2) is found. A charge transfer coefficient α of ∼0.44 is measured. The finding of a superposed constant ohmic resistance due to a solid-liquid electrolyte interphase and a current dependent thermally activated ion transfer process is confirmed by the results of two former experimental studies from the literature, performing AC

  7. Solid polymer electrolyte from phosphorylated chitosan

    Energy Technology Data Exchange (ETDEWEB)

    Fauzi, Iqbal, E-mail: arcana@chem.itb.ac.id; Arcana, I Made, E-mail: arcana@chem.itb.ac.id [Inorganic and Physical Chemistry Research Groups, Faculty of Mathematics and Natural Sciences, Institut Teknologi Bandung, Jl. Ganesha 10, Bandung 40132 (Indonesia)

    2014-03-24

    Recently, the need of secondary battery application continues to increase. The secondary battery which using a liquid electrolyte was indicated had some weakness. A solid polymer electrolyte is an alternative electrolytes membrane which developed in order to replace the liquid electrolyte type. In the present study, the effect of phosphorylation on to polymer electrolyte membrane which synthesized from chitosan and lithium perchlorate salts was investigated. The effect of the component’s composition respectively on the properties of polymer electrolyte, was carried out by analyzed of it’s characterization such as functional groups, ion conductivity, and thermal properties. The mechanical properties i.e tensile resistance and the morphology structure of membrane surface were determined. The phosphorylation processing of polymer electrolyte membrane of chitosan and lithium perchlorate was conducted by immersing with phosphoric acid for 2 hours, and then irradiated on a microwave for 60 seconds. The degree of deacetylation of chitosan derived from shrimp shells was obtained around 75.4%. Relative molecular mass of chitosan was obtained by viscometry method is 796,792 g/mol. The ionic conductivity of chitosan membrane was increase from 6.33 × 10{sup −6} S/cm up to 6.01 × 10{sup −4} S/cm after adding by 15 % solution of lithium perchlorate. After phosphorylation, the ionic conductivity of phosphorylated lithium chitosan membrane was observed 1.37 × 10{sup −3} S/cm, while the tensile resistance of 40.2 MPa with a better thermal resistance. On the strength of electrolyte membrane properties, this polymer electrolyte membrane was suggested had one potential used for polymer electrolyte in field of lithium battery applications.

  8. Solid polymer electrolyte from phosphorylated chitosan

    Science.gov (United States)

    Fauzi, Iqbal; Arcana, I. Made

    2014-03-01

    Recently, the need of secondary battery application continues to increase. The secondary battery which using a liquid electrolyte was indicated had some weakness. A solid polymer electrolyte is an alternative electrolytes membrane which developed in order to replace the liquid electrolyte type. In the present study, the effect of phosphorylation on to polymer electrolyte membrane which synthesized from chitosan and lithium perchlorate salts was investigated. The effect of the component's composition respectively on the properties of polymer electrolyte, was carried out by analyzed of it's characterization such as functional groups, ion conductivity, and thermal properties. The mechanical properties i.e tensile resistance and the morphology structure of membrane surface were determined. The phosphorylation processing of polymer electrolyte membrane of chitosan and lithium perchlorate was conducted by immersing with phosphoric acid for 2 hours, and then irradiated on a microwave for 60 seconds. The degree of deacetylation of chitosan derived from shrimp shells was obtained around 75.4%. Relative molecular mass of chitosan was obtained by viscometry method is 796,792 g/mol. The ionic conductivity of chitosan membrane was increase from 6.33 × 10-6 S/cm up to 6.01 × 10-4 S/cm after adding by 15 % solution of lithium perchlorate. After phosphorylation, the ionic conductivity of phosphorylated lithium chitosan membrane was observed 1.37 × 10-3 S/cm, while the tensile resistance of 40.2 MPa with a better thermal resistance. On the strength of electrolyte membrane properties, this polymer electrolyte membrane was suggested had one potential used for polymer electrolyte in field of lithium battery applications.

  9. New Class of LAGP-Based Solid Polymer Composite Electrolyte for Efficient and Safe Solid-State Lithium Batteries.

    Science.gov (United States)

    Guo, Qingpeng; Han, Yu; Wang, Hui; Xiong, Shizhao; Li, Yujie; Liu, Shuangke; Xie, Kai

    2017-12-06

    Inorganic solid electrolytes (SEs) possess substantial safety and electrochemical stability, which make them as key components of safe rechargeable solid-state Li batteries with high energy density. However, complicated integrally molding process and poor wettability between SEs and active materials are the most challenging barriers for the application of SEs. In this regard, we explore composite SEs of the active ceramic Li1+xAlxGe2-x(PO4)3 (LAGP) as the main medium for ion conduction and the polymer P(VDF-HFP) as a matrix. Meanwhile, for the first time, we choice high chemical, thermal, and electrochemical stability of ionic liquid swelled in polymer, which significantly ameliorate the interface in the cell. In addition, a reduced crystallinity degree of the polymer in the electrolyte can also be achieved. All of these lead to good ionic conductivity of the composite electrolyte (LPELCE), at the same time, good compatibility with the lithium electrode. Especially, high mechanical strength and stable solid electrolyte interphase which suppressed the growth of lithium dendrites and high thermal safety stability can also be observed. For further illustration, the solid-state lithium battery of LiFePO4/LPELCE/Li shows relatively satisfactory performance, indicating the promising potentials of using this type of electrolyte to develop high safety and high energy density solid-state lithium batteries.

  10. First Principles Study of Electrochemical and Chemical Stability of the Solid Electrolyte-Electrode Interfaces in All-Solid-State Li-Ion Batteries

    Science.gov (United States)

    Zhu, Yizhou; He, Xingfeng; Mo, Yifei

    All-solid-state Li-ion battery is a promising next-generation energy-storage technology. Using novel ceramic solid electrolyte materials, all-solid-state battery has advantages of intrinsic safety and high energy density compared to current Li-ion batteries based on organic liquid electrolyte. However, the power density achieved in all-solid-state battery is still unsatisfactory. The high interfacial resistance at electrode-electrolyte interface is one of the major limiting factors. Here we demonstrated a computational approach based on first principles calculation to systematically investigate the chemical and electrochemical stability of solid electrolyte materials, and provide insightful understanding of the degradation and passivation mechanisms at the interface. Our calculation revealed that the intrinsic stability of solid electrolyte materials and solid electrolyte-electrode interfaces is limited and the formation of interphase layers are thermodynamically favorable. Our study demonstrated a computational scheme to evaluate the electrochemical and chemical stability of the solid interfaces. Our newly gained understanding provided principles for developing solid electrolyte materials with enhanced stability and for engineering interfaces in all-solid-state Li-ion batteries. This work was supported by Office of Energy Efficiency and Renewable Energy (DE-EE0006860).

  11. Lithium-ion batteries having conformal solid electrolyte layers

    Science.gov (United States)

    Kim, Gi-Heon; Jung, Yoon Seok

    2014-05-27

    Hybrid solid-liquid electrolyte lithium-ion battery devices are disclosed. Certain devices comprise anodes and cathodes conformally coated with an electron insulating and lithium ion conductive solid electrolyte layer.

  12. Solid electrolytes strengthened by metal dispersions

    Science.gov (United States)

    Lauf, R.J.; Morgan, C.S.

    1981-10-05

    An improvement in solid electrolytes of advanced secondary batteries of the sodium-sulfur, sodium-halogen, and like combinations is achieved by providing said battery with a cermet electrolyte containing a metal dispersion ranging from 0.1 to 10.0 vol. % of a substantially nonreactive metal selected from the group consisting essentially of Pt, Cr, Fe, Co, Ni, Nb, their alloys, and their physical mixtures in the elemental or uncombined state, the remainder of said cermet being an ion-conductive ceramic material.

  13. Electrolytic hydrogen fuel production with solid polymer electrolyte technology.

    Science.gov (United States)

    Titterington, W. A.; Fickett, A. P.

    1973-01-01

    A water electrolysis technology based on a solid polymer electrolyte (SPE) concept is presented for applicability to large-scale hydrogen production in a future energy system. High cell current density operation is selected for the application, and supporting cell test performance data are presented. Demonstrated cell life data are included to support the adaptability of the SPE system to large-size hydrogen generation utility plants as needed for bulk energy storage or transmission. The inherent system advantages of the acid SPE electrolysis technology are explained. System performance predictions are made through the year 2000, along with plant capital and operating cost projections.

  14. Materials Development for All-Solid-State Battery Electrolytes

    Science.gov (United States)

    Wang, Weimin

    Solid electrolytes in all solid-state batteries, provide higher attainable energy density and improved safety. Ideal solid electrolytes require high ionic conductivity, a high elastic modulus to prevent dendrite growth, chemical compatibility with electrodes, and ease of fabrication into thin films. Although various materials types, including polymers, ceramics, and composites, are under intense investigation, unifying design principles have not been identified. In this thesis, we study the key ion transport mechanisms in relation to the structural characteristics of polymers and glassy solids, and apply derived material design strategies to develop polymer-silica hybrid materials with improved electrolyte performance characteristics. Poly(ethylene) oxide-based solid electrolytes containing ceramic nanoparticles are attractive alternatives to liquid electrolytes for high-energy density Li batteries. We compare the effect of Li1.3Al0.3Ti 1.7(PO4)3 active nanoparticles, passive TiO 2 nanoparticles and fumed silica. Up to two orders of magnitude enhancement in ionic conductivity is observed for composites with active nanoparticles, attributed to cation migration through a percolating interphase region that develops around the active nanoparticles, even at low nanoparticle loading. We investigate the structural origin of elastic properties and ionic migration mechanisms in sodium borosilicate and sodium borogermanate glass electrolyte system. A new statistical thermodynamic reaction equilibrium model is used in combination with data from nuclear magnetic resonance and Brillouin light scattering measurements to determine network structural unit fractions. The highly coordinated structural units are found to be predominantly responsible for effective mechanical load transmission, by establishing three-dimensional covalent connectivity. A strong correlation exists between bulk modulus and the activation energy for ion conduction. We describe the activated process in

  15. Non-aqueous electrolytes for electrochemical cells

    Science.gov (United States)

    Zhang, Zhengcheng; Dong, Jian; Amine, Khalil

    2016-06-14

    An electrolyte electrochemical device includes an anodic material and an electrolyte, the electrolyte including an organosilicon solvent, a salt, and a hybrid additiving having a first and a second compound, the hybrid additive configured to form a solid electrolyte interphase film on the anodic material upon application of a potential to the electrochemical device.

  16. Anti-perovskite solid electrolyte compositions

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Yusheng; Daemen, Luc Louis

    2015-12-26

    Solid electrolyte antiperovskite compositions for batteries, capacitors, and other electrochemical devices have chemical formula Li.sub.3OA, Li.sub.(3-x)M.sub.x/2OA, Li.sub.(3-x)N.sub.x/3OA, or LiCOX.sub.zY.sub.(1-z), wherein M and N are divalent and trivalent metals respectively and wherein A is a halide or mixture of halides, and X and Y are halides.

  17. Lithium carbon batteries with solid polymer electrolyte; Accumulateur lithium carbone a electrolyte solide polymere

    Energy Technology Data Exchange (ETDEWEB)

    Andrieu, X.; Boudin, F. [Alcatel Alsthom Recherche, 91 - Marcoussis (France)

    1996-12-31

    The lithium carbon batteries studied in this paper use plasticized polymer electrolytes made with passive polymer matrix swollen by a liquid electrolyte with a high ionic conductivity (> 10{sup -3} S/cm at 25 deg. C). The polymers used to prepare the gels are polyacrylonitrile (PAN) and vinylidene poly-fluoride (PVdF). The electrochemical and physical properties of these materials are analyzed according to their composition. The behaviour of solid electrolytes with different materials of lithium ion insertion (graphite and LiNiO{sub 2}) are studied and compared to liquid electrolytes. The parameters taken into account are the reversible and irreversible capacities, the cycling performance and the admissible current densities. Finally, complete lithium ion batteries with gelled electrolytes were manufactured and tested. (J.S.) 2 refs.

  18. Autogenous electrolyte, non-pyrolytically produced solid capacitor structure

    Science.gov (United States)

    Sharp, Donald J.; Armstrong, Pamela S.; Panitz, Janda Kirk G.

    1998-01-01

    A solid electrolytic capacitor having a solid electrolyte comprising manganese dioxide dispersed in an aromatic polyamide capable of further cure to form polyimide linkages, the solid electrolyte being disposed between a first electrode made of valve metal covered by an anodic oxide film and a second electrode opposite the first electrode. The electrolyte autogenously produces water, oxygen, and hydroxyl groups which act as healing substances and is not itself produced pyrolytically. Reduction of the manganese dioxide and the water molecules released by formation of imide linkages result in substantially improved self-healing of anodic dielectric layer defects.

  19. Autogenous electrolyte, non-pyrolytically produced solid capacitor structure

    Energy Technology Data Exchange (ETDEWEB)

    Sharp, D.J.; Armstrong, P.S.; Paintz, J.K.G.

    1998-04-01

    This report discusses the design of a solid electrolytic capacitor having a solid electrolyte comprised of manganese dioxide dispersed in an aromatic polyamide capable of to forming polyimide linkages. This solid electrolyte being disposed between a first electrode made of valve metal covered by an anodic oxide film and a second electrode opposite the first electrode. The electrolyte autogenously produces water, oxygen, and hydroxyl groups which act as healing substances and is not itself produced pyrolytically. Reduction of the manganese dioxide and the water molecules released by formation of imide linkages result in substantially improved self-healing of anodic dielectric layer defects.

  20. Chemical Passivation of Li(exp +)-Conducting Solid Electrolytes

    Science.gov (United States)

    West, William; Whitacre, Jay; Lim, James

    2008-01-01

    Plates of a solid electrolyte that exhibits high conductivity for positive lithium ions can now be passivated to prevent them from reacting with metallic lithium. Such passivation could enable the construction and operation of high-performance, long-life lithium-based rechargeable electrochemical cells containing metallic lithium anodes. The advantage of this approach, in comparison with a possible alternative approach utilizing lithium-ion graphitic anodes, is that metallic lithium anodes could afford significantly greater energy-storage densities. A major impediment to the development of such cells has been the fact that the available solid electrolytes having the requisite high Li(exp +)-ion conductivity are too highly chemically reactive with metallic lithium to be useful, while those solid electrolytes that do not react excessively with metallic lithium have conductivities too low to be useful. The present passivation method exploits the best features of both extremes of the solid-electrolyte spectrum. The basic idea is to coat a higher-conductivity, higher-reactivity solid electrolyte with a lower-conductivity, lower-reactivity solid electrolyte. One can then safely deposit metallic lithium in contact with the lower-reactivity solid electrolyte without incurring the undesired chemical reactions. The thickness of the lower-reactivity electrolyte must be great enough to afford the desired passivation but not so great as to contribute excessively to the electrical resistance of the cell. The feasibility of this method was demonstrated in experiments on plates of a commercial high-performance solid Li(exp +)- conducting electrolyte. Lithium phosphorous oxynitride (LiPON) was the solid electrolyte used for passivation. LiPON-coated solid-electrolyte plates were found to support electrochemical plating and stripping of Li metal. The electrical resistance contributed by the LiPON layers were found to be small relative to overall cell impedances.

  1. MultiLayer solid electrolyte for lithium thin film batteries

    Science.gov (United States)

    Lee, Se -Hee; Tracy, C. Edwin; Pitts, John Roland; Liu, Ping

    2015-07-28

    A lithium metal thin-film battery composite structure is provided that includes a combination of a thin, stable, solid electrolyte layer [18] such as Lipon, designed in use to be in contact with a lithium metal anode layer; and a rapid-deposit solid electrolyte layer [16] such as LiAlF.sub.4 in contact with the thin, stable, solid electrolyte layer [18]. Batteries made up of or containing these structures are more efficient to produce than other lithium metal batteries that use only a single solid electrolyte. They are also more resistant to stress and strain than batteries made using layers of only the stable, solid electrolyte materials. Furthermore, lithium anode batteries as disclosed herein are useful as rechargeable batteries.

  2. Solid polymer electrolyte composite membrane comprising laser micromachined porous support

    Science.gov (United States)

    Liu, Han [Waltham, MA; LaConti, Anthony B [Lynnfield, MA; Mittelsteadt, Cortney K [Natick, MA; McCallum, Thomas J [Ashland, MA

    2011-01-11

    A solid polymer electrolyte composite membrane and method of manufacturing the same. According to one embodiment, the composite membrane comprises a rigid, non-electrically-conducting support, the support preferably being a sheet of polyimide having a thickness of about 7.5 to 15 microns. The support has a plurality of cylindrical pores extending perpendicularly between opposing top and bottom surfaces of the support. The pores, which preferably have a diameter of about 5 microns, are made by laser micromachining and preferably are arranged in a defined pattern, for example, with fewer pores located in areas of high membrane stress and more pores located in areas of low membrane stress. The pores are filled with a first solid polymer electrolyte, such as a perfluorosulfonic acid (PFSA) polymer. A second solid polymer electrolyte, which may be the same as or different than the first solid polymer electrolyte, may be deposited over the top and/or bottom of the first solid polymer electrolyte.

  3. Solid biopolymer electrolytes came from renewable biopolymer

    Science.gov (United States)

    Wang, Ning; Zhang, Xingxiang; Qiao, Zhijun; Liu, Haihui

    2009-07-01

    Solid polymer electrolytes (SPEs) have attracted many attentions as solid state ionic conductors, because of their advantages such as high energy density, electrochemical stability, and easy processing. SPEs obtained from starch have attracted many attentions in recent years because of its abundant, renewable, low price, biodegradable and biocompatible. In addition, the efficient utilization of biodegradable polymers came from renewable sources is becoming increasingly important due to diminishing resources of fossil fuels as well as white pollution caused by undegradable plastics based on petroleum. So N, N-dimethylacetamide (DMAc) with certain concentration ranges of lithium chloride (LiCl) is used as plasticizers of cornstarch. Li+ can complexes with the carbonyl atoms of DMAc molecules to produce a macro-cation and leave the Cl- free to hydrogen bond with the hydroxyl or carbonyl of starch. This competitive hydrogen bond formation serves to disrupt the intra- and intermolecular hydrogen bonding existed in starch. Therefore, melt extrusion process conditions are used to prepare conductive thermoplastic starch (TPS). The improvements of LiCl concentration increase the water absorption and conductance of TPS. The conductance of TPS containing 0.14 mol LiCl achieve to 10-0.5 S cm-1 with 18 wt% water content.

  4. New Solid Polymer Electrolytes for Improved Lithium Batteries

    Science.gov (United States)

    Hehemann, David G.

    2002-01-01

    The objective of this work was to identify, synthesize and incorporate into a working prototype, next-generation solid polymer electrolytes, that allow our pre-existing solid-state lithium battery to function better under extreme conditions. We have synthesized polymer electrolytes in which emphasis was placed on the temperature-dependent performance of these candidate electrolytes. This project was designed to produce and integrate novel polymer electrolytes into a lightweight thin-film battery that could easily be scaled up for mass production and adapted to different applications.

  5. Solid-polymer-electrolyte fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Fuller, T.F.

    1992-07-01

    A transport model for polymer electrolytes is presented, based on concentrated solution theory and irreversible thermodynamics. Thermodynamic driving forces are developed, transport properties are identified and experiments devised. Transport number of water in Nafion 117 membrane is determined using a concentration cell. It is 1.4 for a membrane equilibrated with saturated water vapor at 25{degrees}C, decreases slowly as the membrane is dehydrated, and falls sharply toward zero as the water content approaches zero. The relation between transference number, transport number, and electroosmotic drag coefficient is presented, and their relevance to water-management is discussed. A mathematical model of transport in a solid-polymer-electrolyte fuel cell is presented. A two-dimensional membrane-electrode assembly is considered. Water management, thermal management, and utilization of fuel are examined in detail. The membrane separators of these fuel cells require sorbed water to maintain conductivity; therefore it is necessary to manage the water content in membranes to ensure efficient operation. Water and thermal management are interrelated. Rate of heat removal is shown to be a critical parameter in the operation of these fuel cells. Current-voltage curves are presented for operation on air and reformed methanol. Equations for convective diffusion to a rotating disk are solved numerically for a consolute point between the bulk concentration and the surface. A singular-perturbation expansion is presented for the condition where the bulk concentration is nearly equal to the consolute-point composition. Results are compared to Levich's solution and analysis.

  6. Solid-polymer-electrolyte fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Fuller, Thomas F. [Univ. of California, Berkeley, CA (United States)

    1992-07-01

    A transport model for polymer electrolytes is presented, based on concentrated solution theory and irreversible thermodynamics. Thermodynamic driving forces are developed, transport properties are identified and experiments devised. Transport number of water in Nafion 117 membrane is determined using a concentration cell. It is 1.4 for a membrane equilibrated with saturated water vapor at 25°C, decreases slowly as the membrane is dehydrated, and falls sharply toward zero as the water content approaches zero. The relation between transference number, transport number, and electroosmotic drag coefficient is presented, and their relevance to water-management is discussed. A mathematical model of transport in a solid-polymer-electrolyte fuel cell is presented. A two-dimensional membrane-electrode assembly is considered. Water management, thermal management, and utilization of fuel are examined in detail. The membrane separators of these fuel cells require sorbed water to maintain conductivity; therefore it is necessary to manage the water content in membranes to ensure efficient operation. Water and thermal management are interrelated. Rate of heat removal is shown to be a critical parameter in the operation of these fuel cells. Current-voltage curves are presented for operation on air and reformed methanol. Equations for convective diffusion to a rotating disk are solved numerically for a consolute point between the bulk concentration and the surface. A singular-perturbation expansion is presented for the condition where the bulk concentration is nearly equal to the consolute-point composition. Results are compared to Levich`s solution and analysis.

  7. PEO nanocomposite polymer electrolyte for solid state symmetric ...

    Indian Academy of Sciences (India)

    Physical and electrochemical properties of polyethylene oxide (PEO)-based nanocomposite solid polymer electrolytes (NPEs) were investigated for symmetric capacitor applications. Nanosize fillers, i.e., Al2O3 and SiO2 incorporated polymer electrolyte exhibited higher ionic conductivity than those with filler-free composites ...

  8. Self-Passivating Lithium/Solid Electrolyte/Iodine Cells

    Science.gov (United States)

    Bugga, Ratnakumar; Whitcare, Jay; Narayanan, Sekharipuram; West, William

    2006-01-01

    Robust lithium/solid electrolyte/iodine electrochemical cells that offer significant advantages over commercial lithium/ iodine cells have been developed. At room temperature, these cells can be discharged at current densities 10 to 30 times those of commercial lithium/iodine cells. Moreover, from room temperature up to 80 C, the maximum discharge-current densities of these cells exceed those of all other solid-electrolyte-based cells. A cell of this type includes a metallic lithium anode in contact with a commercial flexible solid electrolyte film that, in turn, is in contact with an iodine/ graphite cathode. The solid electrolyte (the chemical composition of which has not been reported) offers the high ionic conductivity needed for high cell performance. However, the solid electrolyte exhibits an undesirable chemical reactivity to lithium that, if not mitigated, would render the solid electrolyte unsuitable for use in a lithium cell. In this cell, such mitigation is affected by the formation of a thin passivating layer of lithium iodide at the anode/electrolyte interface. Test cells of this type were fabricated from iodine/graphite cathode pellets, free-standing solid-electrolyte films, and lithium-foil anodes. The cathode mixtures were made by grinding together blends of nominally 10 weight percent graphite and 90 weight percent iodine. The cathode mixtures were then pressed into pellets at 36 kpsi (248 MPa) and inserted into coin-shaped stainless-steel cell cases that were coated with graphite paste to minimize corrosion. The solid-electrolyte film material was stamped to form circular pieces to fit in the coin cell cases, inserted in the cases, and pressed against the cathode pellets with polyethylene gaskets. Lithium-foil anodes were placed directly onto the electrolyte films. The layers described thus far were pressed and held together by stainless- steel shims, wave springs, and coin cell caps. The assembled cells were then crimped to form hermetic seals

  9. Graphene quantum dots as the electrolyte for solid state supercapacitors

    National Research Council Canada - National Science Library

    Zhang, Su; Li, Yutong; Song, Huaihe; Chen, Xiaohong; Zhou, Jisheng; Hong, Song; Huang, Minglu

    2016-01-01

    We propose that graphene quantum dots (GQDs) with a sufficient number of acidic oxygen-bearing functional groups such as -COOH and -OH can serve as solution- and solid- type electrolytes for supercapacitor...

  10. Detailed electrical measurements on sago starch biopolymer solid electrolyte

    Science.gov (United States)

    Singh, Rahul; Baghel, Jaya; Shukla, S.; Bhattacharya, B.; Rhee, Hee-Woo; Singh, Pramod K.

    2014-12-01

    The biopolymer solid electrolyte has been synthesized and characterized. Potassium iodide (KI) has been added in polymer matrix to develop solid polymer electrolyte. Relationships between electrical, ionic transport parameter and mechanism have been studied in detail. Impedance spectroscopy reveals the detailed electrical studies and ion transport mechanism. The ion dissociation factor is compared with a measured dielectric constant at a fixed frequency. The dielectric data are calculated which support the ionic conductivity data.

  11. Halogen acid electrolysis in solid polymer electrolyte cells

    Energy Technology Data Exchange (ETDEWEB)

    Balko, E.N.; McElroy, J.F.; LaConti, A.B.

    1981-01-01

    The use of solid polymer electrolyte systems has been extended to the electrolysis of aqueous HCl and HBr. The reduced internal losses in these cells permits the production of hydrogen and the halogen at an energy consumption considerably less than that reported previously. Data are presented for the operational characteristics of the solid polymer electrolyte acid electrolysers operating over a range of current densities, pressures, feedstock compositions, and temperatures.

  12. Design and Characterisation of Solid Electrolytes for All-Solid-State Lithium Batteries

    DEFF Research Database (Denmark)

    Sveinbjörnsson, Dadi Þorsteinn

    The development of all-solid-state lithium batteries, in which the currently used liquid electrolytes are substituted for solid electrolyte materials, could lead to safer batteries offering higher energy densities and longer cycle lifetimes. Designing suitable solid electrolytes with sufficient......, with the formation of Frenkel pairs playing a large role. The charge and discharge performance of all-solid-state batteries with LiBH4- LiI as an electrolyte is reported for the first time. Lithium titanate (Li4Ti5O12) was used for the positive electrode and lithium metal for the negative electrode...... chemical and electrochemical stability, high lithium ion conduction and negligible electronic conduction remains a challenge. The highly lithium ion conducting LiBH4-LiI solid solution is a promising solid electrolyte material. Solid solutions with a LiI content of 6.25%-50% were synthesised by planetary...

  13. Solid lithium ion conducting electrolytes and methods of preparation

    Science.gov (United States)

    Narula, Chaitanya K; Daniel, Claus

    2013-05-28

    A composition comprised of nanoparticles of lithium ion conducting solid oxide material, wherein the solid oxide material is comprised of lithium ions, and at least one type of metal ion selected from pentavalent metal ions and trivalent lanthanide metal ions. Solution methods useful for synthesizing these solid oxide materials, as well as precursor solutions and components thereof, are also described. The solid oxide materials are incorporated as electrolytes into lithium ion batteries.

  14. Solid electrolyte material manufacturable by polymer processing methods

    Science.gov (United States)

    Singh, Mohit; Gur, Ilan; Eitouni, Hany Basam; Balsara, Nitash Pervez

    2012-09-18

    The present invention relates generally to electrolyte materials. According to an embodiment, the present invention provides for a solid polymer electrolyte material that is ionically conductive, mechanically robust, and can be formed into desirable shapes using conventional polymer processing methods. An exemplary polymer electrolyte material has an elastic modulus in excess of 1.times.10.sup.6 Pa at 90 degrees C. and is characterized by an ionic conductivity of at least 1.times.10.sup.-5 Scm-1 at 90 degrees C. An exemplary material can be characterized by a two domain or three domain material system. An exemplary material can include material components made of diblock polymers or triblock polymers. Many uses are contemplated for the solid polymer electrolyte materials. For example, the present invention can be applied to improve Li-based batteries by means of enabling higher energy density, better thermal and environmental stability, lower rates of self-discharge, enhanced safety, lower manufacturing costs, and novel form factors.

  15. Solid polymer electrolyte composite membrane comprising plasma etched porous support

    Science.gov (United States)

    Liu, Han; LaConti, Anthony B.

    2010-10-05

    A solid polymer electrolyte composite membrane and method of manufacturing the same. According to one embodiment, the composite membrane comprises a rigid, non-electrically-conducting support, the support preferably being a sheet of polyimide having a thickness of about 7.5 to 15 microns. The support has a plurality of cylindrical pores extending perpendicularly between opposing top and bottom surfaces of the support. The pores, which preferably have a diameter of about 0.1 to 5 microns, are made by plasma etching and preferably are arranged in a defined pattern, for example, with fewer pores located in areas of high membrane stress and more pores located in areas of low membrane stress. The pores are filled with a first solid polymer electrolyte, such as a perfluorosulfonic acid (PFSA) polymer. A second solid polymer electrolyte, which may be the same as or different than the first solid polymer electrolyte, may be deposited over the top and/or bottom of the first solid polymer electrolyte.

  16. Low temperature solid oxide electrolytes (LT-SOE): A review

    Science.gov (United States)

    Singh, B.; Ghosh, S.; Aich, S.; Roy, B.

    2017-01-01

    Low temperature solid oxide fuel cell (LT-SOFC) can be a source of power for vehicles, online grid, and at the same time reduce system cost, offer high reliability, and fast start-up. A huge amount of research work, as evident from the literature has been conducted for the enhancement of the ionic conductivity of LT electrolytes in the last few years. The basic conduction mechanisms, advantages and disadvantages of different LT oxide ion conducting electrolytes {BIMEVOX systems, bilayer systems including doped cerium oxide/stabilised bismuth oxide and YSZ/DCO}, mixed ion conducting electrolytes {doped cerium oxides/alkali metal carbonate composites}, and proton conducting electrolytes {doped and undoped BaCeO3, BaZrO3, etc.} are discussed here based on the recent research articles. Effect of various material aspects (composition, doping, layer thickness, etc.), fabrication methods (to achieve different microstructures and particle size), design related strategies (interlayer, sintering aid etc.), characterization temperature & environment on the conductivity of the electrolytes and performance of the fuel cells made from these electrolytes are shown in tabular form and discussed. The conductivity of the electrolytes and performance of the corresponding fuel cells are compared. Other applications of the electrolytes are mentioned. A few considerations regarding the future prospects are pointed.

  17. Development of high performance proton-conducting solid electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Linkous, C.A.; Kopitzke, R.W. [Florida Solar Energy Center, Cocoa, FL (United States)

    1998-08-01

    This work seeks to improve the efficiency of fuel cell and electrolyzer operation by developing solid electrolytes that will function at higher temperatures. Two objectives were pursued: (1) determine the mechanism of hydrolytic decomposition of aromatic sulfonic acid ionomers, with the intent of identifying structural weaknesses that can be avoided in future materials; and (2) identify new directions in solid electrolyte development. After evaluating a number of aromatic sulfonates, it became apparent that no common mechanism was going to be found; instead, each polymer had its own sequence of degradation steps, involving some combination of desulfonation and/or chain scission. For electrochemical cell operation at temperatures > 200 C, it will be necessary to develop solid electrolytes that do not require sulfonic acids and do not require water to maintain its conductivity mechanism.

  18. Graphene quantum dots as the electrolyte for solid state supercapacitors

    Science.gov (United States)

    Zhang, Su; Li, Yutong; Song, Huaihe; Chen, Xiaohong; Zhou, Jisheng; Hong, Song; Huang, Minglu

    2016-01-01

    We propose that graphene quantum dots (GQDs) with a sufficient number of acidic oxygen-bearing functional groups such as -COOH and -OH can serve as solution- and solid- type electrolytes for supercapacitors. Moreover, we found that the ionic conductivity and ion-donating ability of the GQDs could be markedly improved by simply neutralizing their acidic functional groups by using KOH. These neutralized GQDs as the solution- or solid-type electrolytes greatly enhanced the capacitive performance and rate capability of the supercapacitors. The reason for the enhancement can be ascribed to the fully ionization of the weak acidic oxygen-bearing functional groups after neutralization. PMID:26763275

  19. Fuel cells with solid polymer electrolyte and their application on vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Fateev, V.

    1996-04-01

    In Russia, solid polymer electrolyte MF-4-SK has been developed for fuel cells. This electrolyte is based on perfluorinated polymer with functional sulfogroups. Investigations on electrolyte properties and electrocatalysts have been carried out.

  20. Fabrication of cylinder type solid electrolyte electrolytic cell. Entojo kotai denkaishitsugata denkai seru no seizo hoho

    Energy Technology Data Exchange (ETDEWEB)

    Kuru, C.; Nagata, K.; Sasai, T.

    1994-03-18

    With the conventional cylinder type solid electrolyte fuel cell (cylinder type SOFC), the fuel electrode is formed on a supporting tube, and then subjected to heat treatment after the electrolyte is formed. At this time, nickel of the fuel electrode melts to block up pores, and nickel of the fuel electrode must be once made to nickel oxide and reduced to nickel again to avoid blocking up. This invention is concerned with sequential formation of the air electrode having comparatively high conductivity in high temperature oxidizing atmosphere and solid electrolyte of perovskite oxide on the periphery of the cylindrical supporting tube of the cylinder type SOFC, densification of the said air electrode and the solid electrolyte by heat treatment under oxidation atmosphere, and the formation of the fuel electrode on the outermost layer. The oxidation and reduction processes of nickel of the fuel electrode can be eliminated by forming the air electrode and electrolyte in sequence on the supporting tube followed by heat treatment. 1 fig.

  1. Nonlinear ion transport in liquid and solid electrolytes

    Science.gov (United States)

    Roling, B.; Patro, L. N.; Burghaus, O.; Gräf, M.

    2017-08-01

    This paper describes nonlinear ion transport properties of liquid and solid electrolytes. Typically, the relation between ionic current density and electric field becomes nonlinear at electric fields above 50-100 kV/cm. We review the 1st and 2nd Wien effect found in classical strong and weak electrolyte solutions as well as the strong nonlinear ion transport effects observed for inorganic glasses and for polymer electrolytes. Furthermore, we give an overview over models describing nonlinear ion transport in electrolyte solutions, in glasses and in polymers. Recent results are presented for the nonlinear ionic conductivity of supercooled ionic liquids. We show that supercooled ionic liquids exhibit anomalous Wien effects, which are clearly distinct from the classical Wien effects. We also discuss the frequency dependence of higher-order conductivity and permittivity spectra of these liquids.

  2. Electrochemical Synthesis of Ammonia in Solid Electrolyte Cells

    Directory of Open Access Journals (Sweden)

    Ioannis eGaragounis

    2014-01-01

    Full Text Available Developed in the early 1900's, the Haber-Bosch synthesis is the dominant NH3 synthesis process. Parallel to catalyst optimization, current research efforts are also focused on the investigation of new methods for ammonia synthesis, including the electrochemical synthesis with the use of solid electrolyte cells. Since the first report on Solid State Ammonia Synthesis (SSAS, more than 30 solid electrolyte materials were tested and at least 15 catalysts were used as working electrodes. Thus far, the highest rate of ammonia formation reported is 1.13×10−8 mol s−1 cm−2, obtained at 80°C with a Nafion solid electrolyte and a mixed oxide, SmFe0.7Cu0.1Ni0.2O3, cathode. At high temperatures (>500oC the maximum rate was 9.5*10-9 mol s−1 cm−2 using Ce0.8Y0.2O2-δ -[Ca3(PO42 -K3PO4] as electrolyte and Ag-Pd as cathode. In this paper, the advantages and the disadvantages of SSAS vs the conventional process and the requirements that must be met in order to promote the electrochemical process into an industrial level, are discussed.

  3. Solid-state graft copolymer electrolytes for lithium battery applications.

    Science.gov (United States)

    Hu, Qichao; Caputo, Antonio; Sadoway, Donald R

    2013-08-12

    Battery safety has been a very important research area over the past decade. Commercially available lithium ion batteries employ low flash point (battery costs and can malfunction which can lead to battery malfunction and explosions, thus endangering human life. Increases in petroleum prices lead to a huge demand for safe, electric hybrid vehicles that are more economically viable to operate as oil prices continue to rise. Existing organic based electrolytes used in lithium ion batteries are not applicable to high temperature automotive applications. A safer alternative to organic electrolytes is solid polymer electrolytes. This work will highlight the synthesis for a graft copolymer electrolyte (GCE) poly(oxyethylene) methacrylate (POEM) to a block with a lower glass transition temperature (Tg) poly(oxyethylene) acrylate (POEA). The conduction mechanism has been discussed and it has been demonstrated the relationship between polymer segmental motion and ionic conductivity indeed has a Vogel-Tammann-Fulcher (VTF) dependence. Batteries containing commercially available LP30 organic (LiPF6 in ethylene carbonate (EC):dimethyl carbonate (DMC) at a 1:1 ratio) and GCE were cycled at ambient temperature. It was found that at ambient temperature, the batteries containing GCE showed a greater overpotential when compared to LP30 electrolyte. However at temperatures greater than 60 °C, the GCE cell exhibited much lower overpotential due to fast polymer electrolyte conductivity and nearly the full theoretical specific capacity of 170 mAh/g was accessed.

  4. Anion Conduction in Solid Electrolytes Probed by Water Transport Measurement

    OpenAIRE

    Takahashi, Hiroki; Takeguchi, Tatsuya; Yamanaka, Toshiro; Ueda, Wataru

    2010-01-01

    The application of inorganic materials as electrolyte of alkaline fuel cell is an important task to achieve noble-metal-free and high-temperature-resistant fuel cells. In the present study, water transport during ion conduction through solid electrolyte was measured to seek inorganic materials with anion conduction. We discovered the anion conduction in layered oxide NaCo2O4. Although LiCoO2 has the similar layered structure to NaCo2O4, this oxide showed cation conduction.

  5. Electrochemical Interphases for High-Energy Storage Using Reactive Metal Anodes

    KAUST Repository

    Wei, Shuya

    2017-12-11

    Conspectus Stable electrochemical interphases play a critical role in regulating transport of mass and charge in all electrochemical energy storage (EES) systems. In state-of-the-art rechargeable lithium ion batteries, they are rarely formed by design but instead spontaneously emerge from electrochemical degradation of electrolyte and electrode components. High-energy secondary batteries that utilize reactive metal anodes (e.g., Li, Na, Si, Sn, Al) to store large amounts of charge by alloying and/or electrodeposition reactions introduce fundamental challenges that require rational design in order to stabilize the interphases. Chemical instability of the electrodes in contact with electrolytes, morphological instability of the metal–electrolyte interface upon plating and stripping, and hydrodynamic-instability-induced electroconvection of the electrolyte at high currents are all known to cause metal electrode–electrolyte interfaces to continuously evolve in morphology, uniformity, and composition. Additionally, metal anodes undergo large changes in volume during lithiation and delithiation, which means that even in the rare cases where spontaneously formed solid electrode–electrolyte interphases (SEIs) are in thermodynamic equilibrium with the electrode, the SEI is under dynamic strain, which inevitably leads to cracking and/or rupture during extended battery cycling. There is an urgent need for interphases that are able to overcome each of these sources of instability with minimal losses of electrolyte and electrode components. Complementary chemical synthesis strategies are likewise urgently needed to create self-limited and mechanically durable SEIs that are able to flex and shrink to accommodate volume change. These needs are acute for practically relevant cells that cannot utilize large excesses of anode and electrolyte as employed in proof-of-concept-type experiments reported in the scientific literature. This disconnect between practical needs and

  6. Interphase chromosomes

    Indian Academy of Sciences (India)

    First page Back Continue Last page Graphics. Interphase chromosomes. Genomes within interphase nuclei occupy discrete, three-dimensional regions known as 'chromosome territories' (Bridger and Bickmore, 1998, Cremer and Cremer, 2001, Parada and Misteli, 2002). The non-randomness of CT organization within an ...

  7. Alkaline solid polymer electrolytes and their application to rechargeable batteries; Electrolytes solides polymeres alcalins application aux generateurs electrochimiques rechargeables

    Energy Technology Data Exchange (ETDEWEB)

    Guinot, S.

    1996-03-15

    A new family of solid polymer electrolytes (SPE) based on polyoxyethylene (POE), KOH and water is investigated in view of its use in rechargeable batteries. After a short review on rechargeable batteries, the preparation of various electrolyte compositions is described. Their characterization by differential scanning calorimetry (DSC), thermogravimetric analysis, X-ray diffraction and microscopy confirm a multi-phasic structure. Conductivity measurements give values up to 10 sup -3 S cm sup -1 at room temperature. Their use in cells with nickel as negative electrode and cadmium or zinc as positive electrode has been tested; cycling possibility has been shown to be satisfactory. (C.B.) 113 refs.

  8. Evaluation of apatite silicates as solid oxide fuel cell electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Marrero-Lopez, D. [Dpto. de Fisica Aplicada I, Laboratorio de Materiales y Superficies (Unidad Asociada al C.S.I.C.), Universidad de Malaga, 29071 Malaga (Spain); Dpto. de Quimica Inorganica, Universidad de La Laguna, 38200 La Laguna, Tenerife (Spain); Martin-Sedeno, M.C.; Aranda, M.A.G. [Dpto. de Quimica Inorganica, Universidad Malaga, 29071 Malaga (Spain); Pena-Martinez, J. [Dpto. de Quimica Inorganica, Universidad de La Laguna, 38200 La Laguna, Tenerife (Spain); Instituto de Energias Renovables, Parque Tecnologico, Universidad de Castilla La Mancha, 02006 Albacete (Spain); Ruiz-Morales, J.C.; Nunez, P. [Dpto. de Quimica Inorganica, Universidad de La Laguna, 38200 La Laguna, Tenerife (Spain); Ramos-Barrado, J.R. [Dpto. de Fisica Aplicada I, Laboratorio de Materiales y Superficies (Unidad Asociada al C.S.I.C.), Universidad de Malaga, 29071 Malaga (Spain)

    2010-05-01

    Apatite-type silicates have been considered as promising electrolytes for Solid Oxide Fuel Cells (SOFC); however studies on the potential use of these materials in SOFC devices have received relatively little attention. The lanthanum silicate with composition La{sub 10}Si{sub 5.5}Al{sub 0.5}O{sub 26.75} has been evaluated as electrolyte with the electrode materials commonly used in SOFC, i.e. manganite, ferrite and cobaltite as cathode materials and NiO-CGO composite, chromium-manganite and Sr{sub 2}MgMoO{sub 6} as anode materials. Chemical compatibility, area-specific resistance and fuel cell studies have been performed. X-ray powder diffraction (XRPD) analysis did not reveal any trace of reaction products between the apatite electrolyte and most of the aforementioned electrode materials. However, the area-specific polarisation resistance (ASR) of these electrodes in contact with apatite electrolyte increased significantly with the sintering temperature, indicating reactivity at the electrolyte/electrode interface. On the other hand, the ASR values are significantly improved using a ceria buffer layer between the electrolyte and electrode materials to prevent reactivity. Maximum power densities of 195 and 65 mWcm{sup -2} were obtained at 850 and 700 C, respectively in H{sub 2} fuel, using an 1 mm-thick electrolyte, a NiO-Ce{sub 0.8}Gd{sub 0.2}O{sub 1.9} composite as anode and La{sub 0.6}Sr{sub 0.4}Co{sub 0.8}Fe{sub 0.2}O{sub 3-{delta}} as cathode materials. This fuel cell was tested for 100 h in 5%H{sub 2}-Ar atmosphere showing stable performance. (author)

  9. Formation of Reversible Solid Electrolyte Interface on Graphite Surface from Concentrated Electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Dongping; Tao, Jinhui; Yan, Pengfei; Henderson, Wesley A.; Li, Qiuyan; Shao, Yuyan; Helm, Monte L.; Borodin, Oleg; Graff, Gordon L.; Polzin, Bryant; Wang, Chong-Min; Engelhard, Mark; Zhang, Ji-Guang; De Yoreo, James J.; Liu, Jun; Xiao, Jie

    2017-02-10

    Interfacial phenomena have always been key determinants for the performance of energy storage technologies. The solid electrolyte interfacial (SEI) layer, pervasive on the surfaces of battery electrodes for numerous chemical couples, directly affects the ion transport, charge transfer and lifespan of the entire energy system. Almost all SEI layers, however, are unstable resulting in the continuous consumption of the electrolyte. Typically, this leads to the accumulation of degradation products on/restructuring of the electrode surface and thus increased cell impedance, which largely limits the long-term operation of the electrochemical reactions. Herein, a completely new SEI formation mechanism has been discovered, in which the electrolyte components reversibly self-assemble into a protective surface coating on a graphite electrode upon changing the potential. In contrast to the established wisdom regarding the necessity of employing the solvent ethylene carbonate (EC) to form a protective SEI layer on graphite, a wide range of EC-free electrolytes are demonstrated for the reversible intercalation/deintercalation of Li+ cations within a graphite lattice, thereby providing tremendous flexibility in electrolyte tailoring for battery couples. This novel finding is broadly applicable and provides guidance for how to control interfacial reactions through the relationship between ion aggregation and solvent decomposition at polarized interfaces.

  10. Stable lithium electrodeposition in liquid and nanoporous solid electrolytes

    KAUST Repository

    Lu, Yingying

    2014-08-10

    Rechargeable lithium, sodium and aluminium metal-based batteries are among the most versatile platforms for high-energy, cost-effective electrochemical energy storage. Non-uniform metal deposition and dendrite formation on the negative electrode during repeated cycles of charge and discharge are major hurdles to commercialization of energy-storage devices based on each of these chemistries. A long-held view is that unstable electrodeposition is a consequence of inherent characteristics of these metals and their inability to form uniform electrodeposits on surfaces with inevitable defects. We report on electrodeposition of lithium in simple liquid electrolytes and in nanoporous solids infused with liquid electrolytes. We find that simple liquid electrolytes reinforced with halogenated salt blends exhibit stable long-term cycling at room temperature, often with no signs of deposition instabilities over hundreds of cycles of charge and discharge and thousands of operating hours. We rationalize these observations with the help of surface energy data for the electrolyte/lithium interface and impedance analysis of the interface during different stages of cell operation. Our findings provide support for an important recent theoretical prediction that the surface mobility of lithium is significantly enhanced in the presence of lithium halide salts. Our results also show that a high electrolyte modulus is unnecessary for stable electrodeposition of lithium.

  11. Stable lithium electrodeposition in liquid and nanoporous solid electrolytes.

    Science.gov (United States)

    Lu, Yingying; Tu, Zhengyuan; Archer, Lynden A

    2014-10-01

    Rechargeable lithium, sodium and aluminium metal-based batteries are among the most versatile platforms for high-energy, cost-effective electrochemical energy storage. Non-uniform metal deposition and dendrite formation on the negative electrode during repeated cycles of charge and discharge are major hurdles to commercialization of energy-storage devices based on each of these chemistries. A long-held view is that unstable electrodeposition is a consequence of inherent characteristics of these metals and their inability to form uniform electrodeposits on surfaces with inevitable defects. We report on electrodeposition of lithium in simple liquid electrolytes and in nanoporous solids infused with liquid electrolytes. We find that simple liquid electrolytes reinforced with halogenated salt blends exhibit stable long-term cycling at room temperature, often with no signs of deposition instabilities over hundreds of cycles of charge and discharge and thousands of operating hours. We rationalize these observations with the help of surface energy data for the electrolyte/lithium interface and impedance analysis of the interface during different stages of cell operation. Our findings provide support for an important recent theoretical prediction that the surface mobility of lithium is significantly enhanced in the presence of lithium halide salts. Our results also show that a high electrolyte modulus is unnecessary for stable electrodeposition of lithium.

  12. Solid-state Graft Copolymer Electrolytes for Lithium Battery Applications

    Science.gov (United States)

    Hu, Qichao; Caputo, Antonio; Sadoway, Donald R.

    2013-01-01

    Battery safety has been a very important research area over the past decade. Commercially available lithium ion batteries employ low flash point (lithium ion batteries are not applicable to high temperature automotive applications. A safer alternative to organic electrolytes is solid polymer electrolytes. This work will highlight the synthesis for a graft copolymer electrolyte (GCE) poly(oxyethylene) methacrylate (POEM) to a block with a lower glass transition temperature (Tg) poly(oxyethylene) acrylate (POEA). The conduction mechanism has been discussed and it has been demonstrated the relationship between polymer segmental motion and ionic conductivity indeed has a Vogel-Tammann-Fulcher (VTF) dependence. Batteries containing commercially available LP30 organic (LiPF6 in ethylene carbonate (EC):dimethyl carbonate (DMC) at a 1:1 ratio) and GCE were cycled at ambient temperature. It was found that at ambient temperature, the batteries containing GCE showed a greater overpotential when compared to LP30 electrolyte. However at temperatures greater than 60 °C, the GCE cell exhibited much lower overpotential due to fast polymer electrolyte conductivity and nearly the full theoretical specific capacity of 170 mAh/g was accessed. PMID:23963203

  13. Solid electrolyte properties of LaF3

    NARCIS (Netherlands)

    Schoonman, J.; Oversluizen, G.; Wapenaar, K.E.D.

    The small-signal ac response of cells with LaF3 or the solid solutions La1-xBaxF3-x and ionically blocking electrodes has been measured in the frequency range 0.1-3 × 104Hz, and for temperatures from 220 to 650 K. The bulk electrolyte conductivity of LaF3 crystals is anisotropic up to 415 K. For

  14. Multinuclear NMR Study of the Solid Electrolyte Interface Formed in Lithium Metal Batteries

    Energy Technology Data Exchange (ETDEWEB)

    Wan, Chuan; Xu, Suochang; Hu, Mary Y.; Cao, Ruiguo; Qian, Jiangfeng; Qin, Zhaohai; Liu, Jun; Mueller, Karl T.; Zhang, Ji-Guang; Hu, Jian Zhi

    2017-04-18

    The composition of the solid electrolyte interphase (SEI) layers associated with a high performance Cu|Li cell using lithium bis(fluorosulfonyi)imide (LiFSI) in 1,2-dimethoxyethane (DME) as electrolyte is determined by a multinuclear (6Li, 19F, 13C and 1H) solid-state MAS NMR study at high magnetic field (850 MHz). This cell can be cycled at high rates (4 mA•cm-2) for more than 1000 cycles with no increase in the cell impedance at high Columbic efficiency (average of 98.4%) in a highly concentrated LiFSI-DME electrolyte (4 M). LiFSI, LiF, Li2O2 (and/or CH3OLi), LiOH, Li2S and Li2O are observed in the SEI and validated by comparing with the spectra acquired on standard compounds and literature reports. To gain further insight into the role of the solute and its concentration dependence on the formation of SEIs while keeping the solvent of DME unchanged, the SEIs from different concentrations of LiFSI-DME and lithium bis(trifluoromethanesulfonyl)imide (LiTFSI)-DME electrolyte are also investigated. It is found that LiF, a lithiated compound with superior mechanical strength and good Li+ ionic conductivity, is observed in the concentrated 4.0 M LiFSI-DME and the 3.0 M LiTFSI-DME systems but not in the diluted 1.0 M LiFSI-DME system. Li2O exists in both low and high concentration of LiFSI-DME while no Li2O is observed in the LiTFSI system. Furthermore, the dead metallic Li is reduced in the 4 M LiFSI-DME system compared with that in the 1 M LiFSI-DME system. Quantitative 6Li MAS results indicate that the SEI associated with the 4 M LiFSI-DEME is denser or thicker than that of the 1 M LiFSI-DME and the 3 M LiTFSI-DME systems. These findings are likely the reasons for explaining the high electrochemical performance associated with the high concentration LiFSI-DME system.

  15. Strain-Induced Lithium Losses in the Solid Electrolyte Interphase on Silicon Electrodes.

    Science.gov (United States)

    Kumar, Ravi; Lu, Peng; Xiao, Xingcheng; Huang, Zhuangqun; Sheldon, Brian W

    2017-08-30

    The chemical and mechanical stability of SEI layers are particularly important for high capacity anode materials such as silicon, which undergoes large volume changes (∼300%) during cycling. In this work, we present a novel approach for applying controlled strains to SEI films with patterned Si electrodes to systematically investigate the impact of large volume changes on SEI formation and evolution. Comparisons between patterned silicon islands and continuous silicon thin films make it possible to correlate the irreversible capacity losses due to expansion and contraction of underlying silicon. The current work demonstrates that strain in the SEI layer leads to more lithium consumption. The combination of in situ AFM and electrochemical lithium loss measurements provides further information on SEI layer growth. These experiments indicate that in-plane strains in the SEI layer lead to substantial increases in the amount of inorganic phase formation, without significantly affecting the overall SEI thickness. These observations are further supported with EIS and TOF-SIMS results. A map of irreversible capacity evolution with strain in the SEI is obtained from the experimental results.

  16. Failure analysis of electrolyte-supported solid oxide fuel cells

    Science.gov (United States)

    Fleischhauer, Felix; Tiefenauer, Andreas; Graule, Thomas; Danzer, Robert; Mai, Andreas; Kuebler, Jakob

    2014-07-01

    For solid oxide fuel cells (SOFCs) one key aspect is the structural integrity of the cell and hence its thermo mechanical long term behaviour. The present study investigates the failure mechanisms and the actual causes for fracture of electrolyte supported SOFCs which were run using the current μ-CHP system of Hexis AG, Winterthur - Switzerland under lab conditions or at customer sites for up to 40,000 h. In a first step several operated stacks were demounted for post-mortem inspection, followed by a fractographic evaluation of the failed cells. The respective findings are then set into a larger picture including an analysis of the present stresses acting on the cell like thermal and residual stresses and the measurements regarding the temperature dependent electrolyte strength. For all investigated stacks, the mechanical failure of individual cells can be attributed to locally acting bending loads, which rise due to an inhomogeneous and uneven contact between the metallic interconnect and the cell.

  17. Na2SO4-based solid electrolytes for SOx sensors

    DEFF Research Database (Denmark)

    Rao, N.; Schoonman, J.; Toft Sørensen, O.

    1992-01-01

    , SEM, EDX, DTA, TGA and impedance spectroscopy. Upon doping with La2 (SO4)3 or Y2(SO4)3 the high-temperature fast-ion conducting phase NaSO4-I can be stabilized down to room temperature. Doping increases the ionic conductivity as well. Of these solid electrolytes the Na2SO4 + 5 mol% Y2(SO4)3 and Na2SO......, the Na2SO4-I structure can be completely stabilized down to room temperature. For the solid electrolytes with x = 5 and y = 4, Na2WO4 was used to further stabilize phase I, and to improve the mechanical properties. In the Na2SO4 + 5 mol% Y2(SO4)3 + m mol% Na2WO4 (M = 5,10,15,20) and Na2SO4 + 4 mol% La2......(SO4)3 + n mol% Na2WO4 (n = 5, 10,15, 20) samples, XRD analysis reveals the Na2SO4-I structure to be stable at room temperature as is illustrated by DTA. Impedance measurements show that doping these solid solutions with Na2WO4 decreases the ionic conductivity. However, their conductivity is still...

  18. Impedance characterization reveals mixed conducting interphases between sulfidic superionic conductors and lithium metal electrodes

    Science.gov (United States)

    Bron, Philipp; Roling, Bernhard; Dehnen, Stefanie

    2017-06-01

    The impedance of the interface between Li metal anodes and solid electrolytes plays an essential role for the power density of solid-state batteries. We have carried out an impedance spectroscopic study on LGPS-type solid electrolytes in contact to metallic lithium over time periods of several hours. The results reveal that in the case of the highly conductive solid electrolytes Li10GeP2S12, Li10SiP2S12 and Li10Si0.3Sn0.7P2S12, the decomposition layer formed at the interface is a mixed ion-electron conductor (mixed conducting interphase = MCI). The resulting chemical diffusion of Li across the MCI causes a continuous decomposition of the solid electrolyte and a continuous growth of the MCI. From the impedance spectra, we obtain values for the ionic and electronic conductivity of the MCI and for the chemical diffusion coefficient of Li in the MCI. Remarkably, we find that the growth of the MCI is much slower than expected from the chemical diffusion coefficient of Li. This indicates that the growth is not diffusion-controlled, but reaction-controlled. In contrast to the MCI-forming electrolytes, the glass-ceramic 0.95 (0.8 Li2S · 0.2 P2S5) · 0.05 LiI forms a long-term stable solid electrolyte interphase (SEI) in contact to metallic lithium.

  19. Solid-State NMR Study of New Copolymers as Solid Polymer Electrolytes

    Directory of Open Access Journals (Sweden)

    Jean-Christophe Daigle

    2018-01-01

    Full Text Available We report the analysis of comb-like polymers by solid-state NMR. The polymers were previously evaluated as solid-polymer-electrolytes (SPE for lithium-polymer-metal batteries that have suitable ionic conductivity at 60 °C. We propose to develop a correlation between 13C solid-state NMR measurements and phase segregation. 13C solid-state NMR is a perfect tool for differentiating polymer phases with fast or slow motions. 7Li was used to monitor the motion of lithium ions in the polymer, and activation energies were calculated.

  20. Strength of an electrolyte supported solid oxide fuel cell

    Science.gov (United States)

    Fleischhauer, Felix; Bermejo, Raul; Danzer, Robert; Mai, Andreas; Graule, Thomas; Kuebler, Jakob

    2015-11-01

    For the proper function of solid oxide fuel cells (SOFC) their structural integrity must be maintained during their whole lifetime. Any cell fracture would cause leakage and partial oxidization of the anode, leading to a reduced performance, if not catastrophic failure of the whole stack. In this study, the mechanical strength of a state of the art SOFC, developed and produced by Hexis AG/Switzerland, was investigated with respect to the influence of temperature and ageing, whilst for the anode side of the cell the strength was measured under reducing and oxidizing atmospheres. Ball-on-3-Ball bending strength tests and fractography conducted on anode and cathode half-cells revealed the underlying mechanisms, which lead to cell fracture. They were found to be different for the cathode and the anode side and that they change with temperature and ageing. Both anode and cathode sides exhibit the lowest strength at T = 850 °C, which is greatly reduced to the initial strength of the bare electrolyte. This reduction is the consequence of the formation of cracks in the electrode layer which either directly penetrate into the electrolyte (anode side) or locally increase the stress intensity level of pre-existing flaws of the electrolytes at the interface (cathode side).

  1. Solid electrolyte for solid-state batteries: Have lithium-ion batteries reached their technical limit?

    Energy Technology Data Exchange (ETDEWEB)

    Kartini, Evvy [Center for Science and Technology of Advanced Materials – National Nuclear Energy Agency, Kawasan Puspiptek Serpong, Tangerang Selatan15314, Banten (Indonesia); Manawan, Maykel [Post Graduate Program of Materials Science, University of Indonesia, Jl.Salemba Raya No.4, Jakarta 10430 (Indonesia)

    2016-02-08

    With increasing demand for electrical power on a distribution grid lacking storage capabilities, utilities and project developers must stabilize what is currently still intermittent energy production. In fact, over half of utility executives say “the most important emerging energy technology” is energy storage. Advanced, low-cost battery designs are providing promising stationary storage solutions that can ensure reliable, high-quality power for customers, but research challenges and questions lefts. Have lithium-ion batteries (LIBs) reached their technical limit? The industry demands are including high costs, inadequate energy densities, long recharge times, short cycle-life times and safety must be continually addressed. Safety is still the main problem on developing the lithium ion battery.The safety issue must be considered from several aspects, since it would become serious problems, such as an explosion in a Japan Airlines 787 Dreamliner’s cargo hold, due to the battery problem. The combustion is mainly due to the leakage or shortcut of the electrodes, caused by the liquid electrolyte and polymer separator. For this reason, the research on solid electrolyte for replacing the existing liquid electrolyte is very important. The materials used in existing lithium ion battery, such as a separator and liquid electrolyte must be replaced to new solid electrolytes, solid materials that exhibits high ionic conductivity. Due to these reasons, research on solid state ionics materials have been vastly growing worldwide, with the main aim not only to search new solid electrolyte to replace the liquid one, but also looking for low cost materials and environmentally friendly. A revolutionary paradigm is also required to design new stable anode and cathode materials that provide electrochemical cells with high energy, high power, long lifetime and adequate safety at competitive manufacturing costs. Lithium superionic conductors, which can be used as solid electrolytes

  2. Solid electrolyte for solid-state batteries: Have lithium-ion batteries reached their technical limit?

    Science.gov (United States)

    Kartini, Evvy; Manawan, Maykel

    2016-02-01

    With increasing demand for electrical power on a distribution grid lacking storage capabilities, utilities and project developers must stabilize what is currently still intermittent energy production. In fact, over half of utility executives say "the most important emerging energy technology" is energy storage. Advanced, low-cost battery designs are providing promising stationary storage solutions that can ensure reliable, high-quality power for customers, but research challenges and questions lefts. Have lithium-ion batteries (LIBs) reached their technical limit? The industry demands are including high costs, inadequate energy densities, long recharge times, short cycle-life times and safety must be continually addressed. Safety is still the main problem on developing the lithium ion battery.The safety issue must be considered from several aspects, since it would become serious problems, such as an explosion in a Japan Airlines 787 Dreamliner's cargo hold, due to the battery problem. The combustion is mainly due to the leakage or shortcut of the electrodes, caused by the liquid electrolyte and polymer separator. For this reason, the research on solid electrolyte for replacing the existing liquid electrolyte is very important. The materials used in existing lithium ion battery, such as a separator and liquid electrolyte must be replaced to new solid electrolytes, solid materials that exhibits high ionic conductivity. Due to these reasons, research on solid state ionics materials have been vastly growing worldwide, with the main aim not only to search new solid electrolyte to replace the liquid one, but also looking for low cost materials and environmentally friendly. A revolutionary paradigm is also required to design new stable anode and cathode materials that provide electrochemical cells with high energy, high power, long lifetime and adequate safety at competitive manufacturing costs. Lithium superionic conductors, which can be used as solid electrolytes

  3. Improved properties of LiBOB-based solid polymer electrolyte by additive incorporation

    Science.gov (United States)

    Ratri, C.; Sabrina, Q.; Lestariningsih, T.; Wigayati, E.

    2017-04-01

    Solid polymer electrolytes comprising of poly(vinylidene fluoride) (PVdF) and lithium bis (oxalato) borate (LiBOB) have been prepared using solution casting technique. Having an important role in lithium-ion battery system, electrolyte is required to have high ability to transfer lithium ions between electrodes. Safety aspect is the main reason for the development of solid polymer electrolyte as advancement from conventional liquid electrolyte. Nevertheless, solid polymer electrolyte generally has lower conductivities compared to liquid electrolyte. In this research, ceramic additives, as well as plasticiser materials, have been incorporated within the solid polymer electrolyte system to improve its conductivity. Addition of TiO2 filler has proven to increase ionic conductivity by two orders of magnitude. Further improvement was seen in the incorporation of PEG plasticiser, where ionic conductivity was enhanced by three orders of magnitude.

  4. PREPARATION AND CHARACTERIZATION OF SOLID ELECTROLYTES: FUEL CELL APPLICATIONS

    Energy Technology Data Exchange (ETDEWEB)

    Rambabu Bobba; Josef Hormes; T. Wang; Jaymes A. Baker; Donald G. Prier; Tommy Rockwood; Dinesha Hawkins; Saleem Hasan; V. Rayanki

    1997-12-31

    Electrolytes. Ionically conducting solid electrolytes are successfully used for battery, fuel cell and sensor applications.

  5. Solid polymer electrolyte composite membrane comprising a porous support and a solid polymer electrolyte including a dispersed reduced noble metal or noble metal oxide

    Science.gov (United States)

    Liu, Han; Mittelsteadt, Cortney K; Norman, Timothy J; Griffith, Arthur E; LaConti, Anthony B

    2015-02-24

    A solid polymer electrolyte composite membrane and method of manufacturing the same. According to one embodiment, the composite membrane comprises a thin, rigid, dimensionally-stable, non-electrically-conducting support, the support having a plurality of cylindrical, straight-through pores extending perpendicularly between opposing top and bottom surfaces of the support. The pores are unevenly distributed, with some or no pores located along the periphery and more pores located centrally. The pores are completely filled with a solid polymer electrolyte, the solid polymer electrolyte including a dispersed reduced noble metal or noble metal oxide. The solid polymer electrolyte may also be deposited over the top and/or bottom surfaces of the support.

  6. Point Electrode Studies of the Solid Electrolyte-Electrode Interface

    DEFF Research Database (Denmark)

    Jacobsen, Torben

    In the development of new electrode materials for high temperature Solid Oxide Fuel Cells methods are needed for the electrochemical evaluation of the catalytic properties of the materials. A major problem in the comparison of materials is how to determine the geometry and the effective length of......$mm diameter) platinum electrodes mounted in a thin alumina tube resting on a polished 8 mol\\% yttria stabilized zirconia electrolyte at $1000^\\circ$C in air. The results where analysed in terms of the equivalent circuit $R_{YSZ}(R_r Q)$ in the frequency range 0.5MHz--1kHz. Fig.\\,1 shows...... capacities calculated from CPA elements can be questioned, this indicates a change in the interfacial structure. It is noted that after the strong activation in step 11-12 the interface slowly (timescale of days) relaxes toward the equilibrium....

  7. Development of solid electrolytes for water electrolysis at higher temperature

    Energy Technology Data Exchange (ETDEWEB)

    Linkous, C.A. [Florida Solar Energy Center, Cocoa, FL (United States)

    1996-10-01

    This report describes efforts in developing new solid polymer electrolytes that will enable operation of proton exchange membrane electrolyzers at higher temperatures than are currently possible. Several ionomers have been prepared from polyetheretherketone (PEEK), polyethersulfone (PES), and polyphenylquinoxaline (PPQ) by employing various sulfonation procedures. By controlling the extent of sulfonation, a range of proton conductivities could be achieved, whose upper limit actually exceeded that of commercially available perfluoralkyl sulfonates. Thermoconductimetric analysis of samples at various degrees of sulfonation showed an inverse relationship between conductivity and maximum operating temperature. This was attributed to the dual effect of adding sulfonate groups to the polymer: more acid groups produce more protons for increased conductivity, but they also increase water uptake, which mechanically weakens the membrane. This situation was exacerbated by the limited acidity of the aromatic sulfonic acids (pK{sub A} {approx} 2-3). The possibility of using partial fluorination to raise the acid dissociation constant is discussed.

  8. All solid-state sheet battery using lithium inorganic solid electrolyte, thio-LISICON

    Energy Technology Data Exchange (ETDEWEB)

    Inada, Taro [Department of Electronic Chemistry, Interdisciplinary Graduate School of Science and Engineering, Tokyo Institute of Technology, Nagatsuta, Midori, Yokohama, 226-8502 (Japan); Research Center, Denki Kagaku Kogyo K.K., Asahi-machi, Machida, Tokyo, 194-8560 (Japan); Kobayashi, Takeshi [Department of Electronic Chemistry, Interdisciplinary Graduate School of Science and Engineering, Tokyo Institute of Technology, Nagatsuta, Midori, Yokohama, 226-8502 (Japan); Materials Science Research Laboratory, Central Research Institute of Electric Power Industry (CRIEPI), 2-11-1, Iwado-kita, Komae, Tokyo, 201-8511 (Japan); Sonoyama, Noriyuki; Yamada, Atsuo; Nagao, Miki; Kanno, Ryoji [Department of Electronic Chemistry, Interdisciplinary Graduate School of Science and Engineering, Tokyo Institute of Technology, Nagatsuta, Midori, Yokohama, 226-8502 (Japan); Kondo, Shigeo [Department of Chemistry for Materials, Faculty of Engineering, Mie University, 1577 Kurimamachiya-cho, Tsu 514-8507 (Japan)

    2009-12-01

    All solid-state sheet lithium battery was developed using inorganic solid electrolyte, thio-LISICON (Li{sub 3.25}Ge{sub 0.25}P{sub 0.75}S{sub 4}), Li-Al anode, and Mo{sub 6}S{sub 8} cathode materials, and the sheet manufacturing process was established. The new sheet-configuration was consisted of the cathode with the grid of current collector, electrolyte sheet with or without mechanical support, and aluminum/lithium composite sheet anode. A sheet battery with a dimension of 30 mm x 30 mm showed good charge-discharge characteristics without any capacity fading at a current of 0.1 mA. (author)

  9. Superior Blends Solid Polymer Electrolyte with Integrated Hierarchical Architectures for All-Solid-State Lithium-Ion Batteries.

    Science.gov (United States)

    Zhang, Dechao; Zhang, Long; Yang, Kun; Wang, Hongqiang; Yu, Chuang; Xu, Di; Xu, Bo; Wang, Li-Min

    2017-10-25

    Exploration of advanced solid electrolytes with good interfacial stability toward electrodes is a highly relevant research topic for all-solid-state batteries. Here, we report PCL/SN blends integrating with PAN-skeleton as solid polymer electrolyte prepared by a facile method. This polymer electrolyte with hierarchical architectures exhibits high ionic conductivity, large electrochemical windows, high degree flexibility, good flame-retardance ability, and thermal stability (workable at 80 °C). Additionally, it demonstrates superior compatibility and electrochemical stability toward metallic Li as well as LiFePO4 cathode. The electrolyte/electrode interfaces are very stable even subjected to 4.5 V at charging state for long time. The LiFePO4/Li all-solid-state cells based on this electrolyte deliver high capacity, outstanding cycling stability, and superior rate capability better than those based on liquid electrolyte. This solid polymer electrolyte is eligible for next generation high energy density all-solid-state batteries.

  10. Electrode property of single-walled carbon nanotubes in all-solid-state lithium ion battery using polymer electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Sakamoto, Y.; Ishii, Y.; Kawasaki, S., E-mail: kawasaki.shinji@nitech.ac.jp [Nagoya Institute of Technology, Gokiso, Showa, Nagoya, Aichi (Japan)

    2016-07-06

    Electrode properties of single-walled carbon nanotubes (SWCNTs) in an all-solid-state lithium ion battery were investigated using poly-ethylene oxide (PEO) solid electrolyte. Charge-discharge curves of SWCNTs in the solid electrolyte cell were successfully observed. It was found that PEO electrolyte decomposes on the surface of SWCNTs.

  11. Yttria-stabilized zirconia solid oxide electrolyte fuel cells: Monolithic solid oxide fuel cells

    Science.gov (United States)

    1990-10-01

    The monolithic solid oxide fuel cell (MSOFC) is currently under development for a variety of applications including coal-based power generation. The MSOFC is a design concept that places the thin components of a solid oxide fuel cell in lightweight, compact, corrugated structure, and so achieves high efficiency and excellent performance simultaneously with high power density. The MSOFC can be integrated with coal gasification plants and is expected to have high overall efficiency in the conversion of the chemical energy of coal to electrical energy. This report describes work aimed at: (1) assessing manufacturing costs for the MSOFC and system costs for a coal-based plant; (2) modifying electrodes and electrode/electrolyte interfaces to improve the electrochemical performance of the MSOFC; and (3) testing the performance of the MSOFC on hydrogen and simulated coal gas. Manufacturing costs for both the coflow and crossflow MSOFC's were assessed based on the fabrication flow charts developed by direct scaleup of tape calendering and other laboratory processes. Integrated coal-based MSOFC systems were investigated to determine capital costs and costs of electricity. Design criteria were established for a coal-fueled 200-Mw power plant. Four plant arrangements were evaluated, and plant performance was analyzed. Interfacial modification involved modification of electrodes and electrode/electrolyte interfaces to improve the MSOFC electrochemical performance. Work in the cathode and cathode/electrolyte interface was concentrated on modification of electrode porosity, electrode morphology, electrode material, and interfacial bonding. Modifications of the anode and anode/electrolyte interface included the use of additives and improvement of nickel distribution. Single cells have been tested for their electrochemical performance. Performance data were typically obtained with humidified H2 or simulated coal gas and air or oxygen.

  12. Chitosan-gold-Lithium nanocomposites as solid polymer electrolyte.

    Science.gov (United States)

    Begum, S N Suraiya; Pandian, Ramanathaswamy; Aswal, Vinod K; Ramasamy, Radha Perumal

    2014-08-01

    Lithium micro batteries are emerging field of research. For environmental safety biodegradable films are preferred. Recently biodegradable polymers have gained wide application in the field of solid polymer electrolytes. To make biodegradable polymers films plasticizers are usually used. However, use of plasticizers has disadvantages such as inhomogenities in phases and mechanical instability that will affect the performance of Lithium micro batteries. We have in this research used gold nanoparticles that are environmentally friendly, instead of plasticizers. Gold nanoparticles were directly template upon chitosan membranes by reduction process so as to enhance the interactions of Lithium with the polymer. In this article, for the first time the characteristics of Chitosan-gold-Lithium nanocomposite films are investigated. The films were prepared using simple solution casting technique. We have used various characterization tools such as Small Angle Neutron Scattering (SANS), XRD, FTIR, Raman, FESEM, and AFM, Light scattering, Dielectric and electrical conductivity measurements. Our investigations show that incorporation of gold results in enhancement of conductivity in Lithium containing Chitosan films. Also it affects the dielectric characteristics of the films. We conclude through various characterization tools that the enhancement in the conductivity was due to the retardation of crystal growth of lithium salt in the presence of gold nanoparticles. A model is proposed regarding the formation of the new nanocomposite. The conductivity of these biodegradable films is comparable to those of the current inorganic Lithium micro batteries. This new chitosan-Au-Li nanocomposite has potential applications in the field of Lithium micro batteries.

  13. Complex hydrides as room-temperature solid electrolytes for rechargeable batteries

    NARCIS (Netherlands)

    de Jongh, P. E.|info:eu-repo/dai/nl/186125372; Blanchard, D.; Matsuo, M.; Udovic, T. J.; Orimo, S.

    A central goal in current battery research is to increase the safety and energy density of Li-ion batteries. Electrolytes nowadays typically consist of lithium salts dissolved in organic solvents. Solid electrolytes could facilitate safer batteries with higher capacities, as they are compatible with

  14. Complex hydrides as room-temperature solid electrolytes for rechargeable batteries

    DEFF Research Database (Denmark)

    Jongh, P. E. de; Blanchard, D.; Matsuo, M.

    2016-01-01

    A central goal in current battery research is to increase the safety and energy density of Li-ion batteries. Electrolytes nowadays typically consist of lithium salts dissolved in organic solvents. Solid electrolytes could facilitate safer batteries with higher capacities, as they are compatible w...

  15. Vapor-Liquid-Solid Equilibria of Sulfur Dioxide in Aqueous Electrolyte Solutions

    DEFF Research Database (Denmark)

    Pereda, Selva; Thomsen, Kaj; Rasmussen, Peter

    2000-01-01

    The Extended UNIQUAC model for electrolyte systems, combined with the Soave-Redlich-Kwong equation of state is used to describe the complex vapor-liquid-solid equilibria of sulfur dioxide in electrolyte solutions. Model parameters based on 1500 experimental data points are presented. The parameters...

  16. Safety of solid-state Li metal battery: Solid polymer versus liquid electrolyte

    Science.gov (United States)

    Perea, Alexis; Dontigny, Martin; Zaghib, Karim

    2017-08-01

    In this article we present the difference in thermal stability of Li/LiFePO4| half cells with liquid and solid polymer electrolytes. After two initial cycles, the cells were charged to two different state of charge (SOC) of 50 and 100%. The thermal stability of the half cells is assessed with an accelerating rate calorimeter, and the thermal runaway parameters are discussed for each experiment: dependence of self-heating rate on temperature, temperature of a first-detected exothermic reaction, and maximum cell temperature. The dependence of those parameters with respect to the SOC is also presented.

  17. Wetting of Nano-Confined Electrodes By Lithium-Ion Battery Electrolytes Using Multiple Beam Interferometry

    OpenAIRE

    Moeremans, Boaz; Cheng, Hsiu-Wei; Garces, Hector; Padture, Nitin; Hardy, An; Renner, Frank Uwe; Valtiner, Markus

    2015-01-01

    The interface with the electrolyte is a decisive feature in the design of composite battery electrodes, which typically contain active material particles, conductive material, and polymer binder. A detailed understanding of the electrolyte layering and wetting of materials such as graphene, graphites, metals such as aluminum or even gold, silicon, and metal oxides are ultimately important for improving crucial lithium-ion battery mechanisms. In particular the solid electrolyte interphase (SEI...

  18. Lithiated and sulphonated poly(ether ether ketone) solid state electrolyte films for supercapacitors

    Energy Technology Data Exchange (ETDEWEB)

    Chiu, K.-F.; Su, S.-H., E-mail: minimono42@gmail.com

    2013-10-01

    Poly(ether ether ketone) (PEEK) films have been synthesised and used as solid-state electrolytes for supercapacitors. In order to increase their ion conductivity, the PEEK films were sulphonated by sulphuric acid, and various amounts of LiClO{sub 4} were added. The solid-state electrolyte films were characterised by Fourier transform infrared spectroscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy, and thermogravimetric analysis. The ionic conductivities of the electrolyte films were analysed by performing electrochemical impedance spectroscopy. The obtained electrolyte films can be sandwiched or directly coated on activated carbon electrodes to form solid-state supercapacitors. The electrochemical characteristics of these supercapacitors were investigated by performing cyclic voltammetry and charge–discharge tests. Under an optimal content of LiClO{sub 4}, the supercapacitor can provide a capacitance as high as 190 F/g. After 1000 cycles, the supercapacitors show almost no capacitance fading, indicating high stability of the solid-state electrolyte films. - Highlights: • Poly(ether ether ketone) (PEEK) films have been used as solid-state electrolytes. • LiClO4 addition can efficiently improve the ionic conductivity. • Supercapacitors using PEEK electrolyte films deliver high capacitance.

  19. Recent Developments of All-Solid-State Lithium Secondary Batteries with Sulfide Inorganic Electrolytes.

    Science.gov (United States)

    Xu, Ruochen; Zhang, Shengzhao; Wang, Xiuli; Xia, Yan; Xia, Xinhui; Wu, Jianbo; Gu, Changdong; Tu, Jiangping

    2017-10-25

    Due to the increasing demand of security and energy density, all-solid-state lithium ion batteries have become the promising next-generation energy storage devices to replace the traditional liquid batteries with flammable organic electrolytes. In this Minireview, we focus on the recent developments of sulfide inorganic electrolytes for all-solid-state batteries. The challenges of assembling bulk-type all-solid-state batteries for industrialization are discussed, including low ionic conductivity of the present sulfide electrolytes, high interfacial resistance and poor compatibility between electrolytes and electrodes. Many efforts have been focused on the solutions for these issues. Although some progresses have been achieved, it is still far away from practical application. The perspectives for future research on all-solid-state lithium ion batteries are presented. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  20. Development of rechargeable lithium-bromine batteries with lithium ion conducting solid electrolyte

    Science.gov (United States)

    Takemoto, Koshin; Yamada, Hirotoshi

    2015-05-01

    Electrochemical performances of a prototype lithium-bromine battery (LBB) employing a solid electrolyte is investigated. The discharge capacity decreases with repeating charge/discharge cycles. Electrochemical impedance analysis reveals that the capacity fading is mainly due to increase in the interfacial resistance between an aqueous active material solution and a solid electrolyte. Based on the results of symmetric cells and structural analysis of the surface of the solid electrolyte immersed in Br2 solutions, it is suggested that a Li+-depletion layer is formed on the surface of the solid electrolyte as a result of contact with bromine. Addition of tetraethylammonium bromide (TEABr) depresses the interfacial resistance, which results in improved cycleability. LBB with 1.0 M LiBr and 0.25 M TEABr shows discharge capacity of 139 mAh/g-LiBr and Coulombic efficiency of 99.6% at 5th cycle.

  1. Lithium ion conducting solid polymer blend electrolyte based on bio ...

    Indian Academy of Sciences (India)

    Lithium ion conducting polymer blend electrolyte films based on poly(vinyl alcohol) (PVA) and poly(vinyl pyrrolidone) (PVP) with different Mwt% of lithium nitrate (LiNO3) salt, using a solution cast technique, have been prepared. The polymer blend electrolyte has been characterized by XRD, FTIR, DSC and impedance ...

  2. Nano-sponge ionic liquid-polymer composite electrolytes for solid-state lithium power sources

    Energy Technology Data Exchange (ETDEWEB)

    Liao, Kang-Shyang; Andreoli, Enrico; Curran, Seamus A. [Department of Physics, University of Houston, Houston, TX 77004 (United States); Sutto, Thomas E. [Naval Research Labs-DC, Materials Science and Technology Division, Washington, DC 20375 (United States); Ajayan, Pulickel [Department of Materials Engineering, Rice University, Houston, TX 77005 (United States); McGrady, Karen A. [Marine Corps System Command, 50 Tech Parkway, Garrisonville, VA 22463 (United States)

    2010-02-01

    Solid polymer gel electrolytes composed of 75 wt.% of the ionic liquid, 1-n-butyl-2,3-dimethylimidazolium bis-trifluoromethanesulfonylimide with 1.0 M lithium bis-trifluoromethanesulfonylimide and 25 wt.% poly(vinylidenedifluoro-hexafluoropropene) are characterized as the electrolyte/separator in solid-state lithium batteries. The ionic conductivity of these gels ranges from 1.5 to 2.0 mS cm{sup -1}, which is several orders of magnitude more conductive than any of the more commonly used solid polymers, and comparable to the best solid gel electrolytes currently used in industry. TGA indicates that these polymer gel electrolytes are thermally stable to over 280 C, and do not begin to thermally decompose until over 300 C; exhibiting a significant advancement in the safety of lithium batteries. Atomic force microscopy images of these solid thin films indicate that these polymer gel electrolytes have the structure of nano-sponges, with a sub-micron pore size. For these thin film batteries, 150 charge-discharge cycles are run for Li{sub x}CoO{sub 2} where x is cycled between 0.95 down to 0.55. Minimal internal resistance effects are observed over the charging cycles, indicating the high ionic conductivity of the ionic liquid solid polymer gel electrolyte. The overall cell efficiency is approximately 98%, and no significant loss in battery efficiency is observed over the 150 cycles. (author)

  3. Accessing the bottleneck in all-solid state batteries, lithium-ion transport over the solid-electrolyte-electrode interface

    NARCIS (Netherlands)

    Yu, C.; Ganapathy, S.; van Eck, Ernst R H; Wang, H.; Basak, S.; Li, Z.; Wagemaker, M.

    2017-01-01

    Solid-state batteries potentially offer increased lithium-ion battery energy density and safety as required for large-scale production of electrical vehicles. One of the key challenges toward high-performance solid-state batteries is the large impedance posed by the electrode-electrolyte

  4. Characterization of Pvp Based Solid Polymer Electrolytes Using Spectroscopic Techniques

    Science.gov (United States)

    Ramya, C. S.; Selvasekarapandian, S.; Bhuvaneswari, M. S.; Savitha, T.

    2006-06-01

    Polymer electrolytes based on poly (vinyl pyrrolidone) - ammonium thiocyanate have beeri prepared by solution cast technique. The interaction of salt with the polymer has been examined using Raman spectroscopy. Results revealed that the interaction of the salt has been found to be through the carbonyl group of the polymer matrix. Conductivity measurements showed that these systems conduct ionically. The possible correlation between the conductivity and the structure of these electrolytic systems was also investigated which shows that the conductivity values are directly related to the total "free anion" concentration. Conductivity analysis showed that the addition of ammonium thiocyanate as a dopant in the polymeric electrolyte system enhanced the ionic conductivity. 20 mol% ammonium thiocyanate doped polymer electrolyte exhibits high ionic conductivity and has been found to be 1.7 × 10-4 S cm-1, at room temperature.

  5. Structural and electrical properties of lithio-borate solid electrolyte thin films

    Science.gov (United States)

    Dzwonkowski, P.; Julien, C.; Balkanski, M.

    1988-09-01

    The effect of deposition conditions on the growth structure of amorphous thin films of lithio-borate solid electrolyte was investigated by means of infrared absorption and complex impedance spectroscopies. Thin films of vitreous solid electrolyte in the alkali-oxide/borate-oxide system were grown by vacuum quasi-flash evaporation. The complex impedance measurements of the thin solid films in the sandwich geometry show a high ionic conductivity. Incorporation of lithium salt dopant has been also studied. The structure was determined using infrared absorption spectra which are sensitive to deposition conditions and to the amount of lithium incorporated.

  6. Hybrid Lithium-Sulfur Batteries with a Solid Electrolyte Membrane and Lithium Polysulfide Catholyte.

    Science.gov (United States)

    Yu, Xingwen; Bi, Zhonghe; Zhao, Feng; Manthiram, Arumugam

    2015-08-05

    Lithium-sulfur (Li-S) batteries are receiving great attention as the most promising next-generation power source with significantly high charge-storage capacity. However, the implementation of Li-S batteries is hampered by a critical challenge because of the soluble nature of the intermediate polysulfide species in the liquid electrolyte. The use of traditional porous separators unavoidably allows the migration of the dissolved polysulfide species from the cathode to the lithium-metal anode and results in continuous loss of capacity. In this study, a LiSICON (lithium super ionic conductor) solid membrane is used as a cation-selective electrolyte for lithium-polysulfide (Li-PS) batteries to suppress the polysulfide diffusion. Ionic conductivity issue at the lithium metal/solid electrolyte interface is successfully addressed by insertion of a "soft", liquid-electrolyte integrated polypropylene interlayer. The solid LiSICON lithium-ion conductor maintains stable ionic conductivity during the electrochemical cycling of the cells. The Li-PS battery system with a hybrid solid/liquid electrolyte exhibits significantly enhanced cyclability relative to the cells with the traditional liquid-electrolyte integrated porous separator.

  7. All-Solid-State Lithium-Ion Batteries with Grafted Ceramic Nanoparticles Dispersed in Solid Polymer Electrolytes.

    Science.gov (United States)

    Lago, Nerea; Garcia-Calvo, Oihane; Lopez del Amo, Juan Miguel; Rojo, Teofilo; Armand, Michel

    2015-09-21

    Lithium-based rechargeable batteries offer superior specific energy and power, and have enabled exponential growth in industries focused on small electronic devices. However, further increases in energy density, for example for electric transportation, face the challenge of harnessing the lithium metal as negative electrode instead of limited-capacity graphite and its heavy copper current collector. All-solid-state batteries utilize solid polymer electrolytes (SPEs) to overcome the safety issues of liquid electrolytes. We demonstrate an all-solid-state lithium-ion battery by using plasticized poly(ethylene oxide)-based SPEs comprising anions grafted or co-grafted onto ceramic nanoparticles. This new approach using grafted ceramic nanoparticles enables the development of a new generation of nanohybrid polymer electrolytes with high ionic conductivity as well as high electrochemical and mechanical stability, enabling Li-ion batteries with long cycle life. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  8. Designer interphases for the lithium-oxygen electrochemical cell

    KAUST Repository

    Choudhury, Snehashis

    2017-04-20

    An electrochemical cell based on the reversible oxygen reduction reaction: 2Li+ + 2e− + O2 ↔ Li2O2, provides among the most energy dense platforms for portable electrical energy storage. Such Lithium-Oxygen (Li-O2) cells offer specific energies competitive with fossil fuels and are considered promising for electrified transportation. Multiple, fundamental challenges with the cathode, anode, and electrolyte have limited practical interest in Li-O2 cells because these problems lead to as many practical shortcomings, including poor rechargeability, high overpotentials, and specific energies well below theoretical expectations. We create and study in-situ formation of solid-electrolyte interphases (SEIs) based on bromide ionomers tethered to a Li anode that take advantage of three powerful processes for overcoming the most stubborn of these challenges. The ionomer SEIs are shown to protect the Li anode against parasitic reactions and also stabilize Li electrodeposition during cell recharge. Bromine species liberated during the anchoring reaction also function as redox mediators at the cathode, reducing the charge overpotential. Finally, the ionomer SEI forms a stable interphase with Li, which protects the metal in high Gutmann donor number liquid electrolytes. Such electrolytes have been reported to exhibit rare stability against nucleophilic attack by Li2O2 and other cathode reaction intermediates, but also react spontaneously with Li metal anodes. We conclude that rationally designed SEIs able to regulate transport of matter and ions at the electrolyte/anode interface provide a promising platform for addressing three major technical barriers to practical Li-O2 cells.

  9. Designer interphases for the lithium-oxygen electrochemical cell.

    Science.gov (United States)

    Choudhury, Snehashis; Wan, Charles Tai-Chieh; Al Sadat, Wajdi I; Tu, Zhengyuan; Lau, Sampson; Zachman, Michael J; Kourkoutis, Lena F; Archer, Lynden A

    2017-04-01

    An electrochemical cell based on the reversible oxygen reduction reaction: 2Li(+) + 2e (-) + O2↔ Li2O2, provides among the most energy dense platforms for portable electrical energy storage. Such Lithium-Oxygen (Li-O2) cells offer specific energies competitive with fossil fuels and are considered promising for electrified transportation. Multiple, fundamental challenges with the cathode, anode, and electrolyte have limited practical interest in Li-O2 cells because these problems lead to as many practical shortcomings, including poor rechargeability, high overpotentials, and specific energies well below theoretical expectations. We create and study in-situ formation of solid-electrolyte interphases (SEIs) based on bromide ionomers tethered to a Li anode that take advantage of three powerful processes for overcoming the most stubborn of these challenges. The ionomer SEIs are shown to protect the Li anode against parasitic reactions and also stabilize Li electrodeposition during cell recharge. Bromine species liberated during the anchoring reaction also function as redox mediators at the cathode, reducing the charge overpotential. Finally, the ionomer SEI forms a stable interphase with Li, which protects the metal in high Gutmann donor number liquid electrolytes. Such electrolytes have been reported to exhibit rare stability against nucleophilic attack by Li2O2 and other cathode reaction intermediates, but also react spontaneously with Li metal anodes. We conclude that rationally designed SEIs able to regulate transport of matter and ions at the electrolyte/anode interface provide a promising platform for addressing three major technical barriers to practical Li-O2 cells.

  10. High temperature lithium cells with solid polymer electrolytes

    Science.gov (United States)

    Yang, Jin; Eitouni, Hany Basam; Singh, Mohit

    2017-03-07

    Electrochemical cells that use electrolytes made from new polymer compositions based on poly(2,6-dimethyl-1,4-phenylene oxide) and other high-softening-temperature polymers are disclosed. These materials have a microphase domain structure that has an ionically-conductive phase and a phase with good mechanical strength and a high softening temperature. In one arrangement, the structural block has a softening temperature of about 210.degree. C. These materials can be made with either homopolymers or with block copolymers. Such electrochemical cells can operate safely at higher temperatures than have been possible before, especially in lithium cells. The ionic conductivity of the electrolytes increases with increasing temperature.

  11. Fermi Potential across Working Solid Oxide Cells with Zirconia or Ceria Electrolytes

    DEFF Research Database (Denmark)

    Jacobsen, Torben; Chatzichristodoulou, Christodoulos; Mogensen, Mogens Bjerg

    2014-01-01

    Two kinds of electrochemical relevant potentials are important in order to describe several observed phenomena in operating electrochemical cells with solid electrolytes. This paper gives illustrative examples of how the profiles of the two potential types, the Galvani potential, φ, and the elect...... stabilized zirconia (YSZ) electrolytes. The nature of the two potential types and the importance of each of them for the cell operation are explained....

  12. Study of lithium glassy solid electrolyte/electrode interface by ...

    Indian Academy of Sciences (India)

    Unknown

    †Present address: Departamento de Engenharia de Materiais, Instituto Superior Technico, Av. Rovisco Pais. 1049-001, LISBOA Codex. MS received 7 April 2000. Abstract. Cells of lithium ion conducting glassy electrolyte Li2SO4–Li2O–B2O3 with different combinations of electrodes (stainless steel blocking electrode, ...

  13. Lithium ion conducting solid polymer blend electrolyte based on bio ...

    Indian Academy of Sciences (India)

    vinyl alcohol) (PVA) and poly(vinyl pyrrolidone) (PVP) with different Mwt% of lithium nitrate (LiNO3) salt, using a solution cast technique, have been prepared. The polymer blend electrolyte has been characterized by XRD, FTIR, DSC and ...

  14. Study of lithium glassy solid electrolyte/electrode interface by ...

    Indian Academy of Sciences (India)

    Cells of lithium ion conducting glassy electrolyte Li2SO4–Li2O–B2O3 with different combinations of electrodes (stainless steel blocking electrode, lithium non-blocking electrode and TiS2 electrode) have been prepared. The a.c. impedance measurements of the cells have been studied at elevated temperature as a function ...

  15. Microwave assisted sintering of gadolinium doped barium cerate electrolyte for intermediate temperature solid oxide fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, Arumugam Senthil, E-mail: senthu.ramp@gmail.com [Department of Physics, PSG College of Technology, Coimbatore, 641 004, Tamilnadu (India); Balaji, Ramamoorthy [Department of Physics, PSG College of Technology, Coimbatore, 641 004, Tamilnadu (India); Jayakumar, Srinivasalu [Department of Physics, PSG Institute of Technology and Applied Research, Coimbatore, 641 062, Tamilnadu (India); Pradeep, Chandran [Department of Physics, Indian Institute of Technology, Madras, 600 036, Tamilnadu (India)

    2016-10-01

    In Solid Oxide Fuel Cell (SOFC), electrolyte plays a vital role to increase the energy conversion efficiency. The main hurdle of such electrolyte in fuel cell is its higher operating temperature (1000 °C) which results in design limitation and higher fabrication cost. In order to reduce the operating temperature of SOFC, a suitable electrolyte has been prepared through co-precipitation method followed by microwave sintering of solid ceramic. The calcination temperature for the as-prepared powder was identified using Differential Scanning Calorimetry. The crystal structure of the sample was found to exhibit its orthorhombic perovskite structure. The particle size was determined using High-Resolution Transmission Electron Microscope with uniform in shape and size, match with XRD results and confirmed from structural analysis. Thus, the sample prepared via co-precipitation method and the solid ceramic sintered through microwave can be a promising electrolyte for fuel cells operated at intermediate temperature. - Highlights: • To synthesis the composite electrolyte by chemical method and sinter using microwave. • To reduce the operating temperature of electrolyte for high ionic conductivity in SOFC's. • To study the phase purity and to develop nanocomposite at reduced temperature.

  16. High efficiency solid state dye sensitized solar cells with graphene-polyethylene oxide composite electrolytes.

    Science.gov (United States)

    Akhtar, M Shaheer; Kwon, Soonji; Stadler, Florian J; Yang, O Bong

    2013-06-21

    Novel and highly effective composite electrolytes were prepared by combining the two dimensional graphene (Gra) and polyethylene oxide (PEO) for the solid electrolyte of dye sensitized solar cells (DSSCs). Gra sheets were uniformly coated by the polymer layer through the ester carboxylate bonding between oxygenated species on Gra sheets and PEO. The Gra-PEO composite electrolyte showed the large scale generation of iodide ions in a redox couple. From rheological analysis, the decrease in viscosity after the addition of LiI and I2 in the Gra-PEO electrolyte might be explained by the dipolar interactions being severely disrupted by the ionic interactions of Li(+), I(-), and I3(-) ions. A composite electrolyte with 0.5 wt% Gra presented a higher ionic conductivity (3.32 mS cm(-1)) than those of PEO and other composite electrolytes at room temperature. A high overall conversion efficiency (∼5.23%) with a very high short circuit current (JSC) of 18.32 mA cm(-2), open circuit voltage (VOC) of 0.592 V and fill factor (FF) of 0.48 was achieved in DSSCs fabricated with the 0.5 wt% Gra-PEO composite electrolyte. This enhanced photovoltaic performance might be attributed to the large scale formation of iodide ions in the redox electrolyte and the relatively high ionic conductivity.

  17. Superior Conductive Solid-like Electrolytes: Nanoconfining Liquids within the Hollow Structures.

    Science.gov (United States)

    Zhang, Jinshui; Bai, Ying; Sun, Xiao-Guang; Li, Yunchao; Guo, Bingkun; Chen, Jihua; Veith, Gabriel M; Hensley, Dale K; Paranthaman, Mariappan Parans; Goodenough, John B; Dai, Sheng

    2015-05-13

    The growth and proliferation of lithium (Li) dendrites during cell recharge are currently unavoidable, which seriously hinders the development and application of rechargeable Li metal batteries. Solid electrolytes with robust mechanical modulus are regarded as a promising approach to overcome the dendrite problems. However, their room-temperature ionic conductivities are usually too low to reach the level required for normal battery operation. Here, a class of novel solid electrolytes with liquid-like room-temperature ionic conductivities (>1 mS cm(-1)) has been successfully synthesized by taking advantage of the unique nanoarchitectures of hollow silica (HS) spheres to confine liquid electrolytes in hollow space to afford high conductivities (2.5 mS cm(-1)). In a symmetric lithium/lithium cell, the solid-like electrolytes demonstrate a robust performance against the Li dendrite problem, preventing the cell from short circuiting at current densities ranging from 0.16 to 0.32 mA cm(-2) over an extended period of time. Moreover, the high flexibility and compatibility of HS nanoarchitectures, in principle, enables broad tunability to choose desired liquids for the fabrication of other kinds of solid-like electrolytes, such as those containing Na(+), Mg(2+), or Al(3+) as conductive media, providing a useful alternative strategy for the development of next generation rechargeable batteries.

  18. Superior Conductive Solid-like Electrolytes: Nanoconfining Liquids within the Hollow Structures

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Jinshui [ORNL; Bai, Ying [ORNL; Sun, Xiao-Guang [ORNL; Li, Yunchao [ORNL; Guo, Bingkun [ORNL; Chen, Jihua [ORNL; Veith, Gabriel M [ORNL; Hensley, Dale K [ORNL; Paranthaman, Mariappan Parans [ORNL; Goodenough, John B [University of Texas at Austin; Dai, Sheng [ORNL

    2015-01-01

    The growth and proliferation of lithium (Li) dendrites during cell recharge is unavoidable, which seriously hinders the development and application of rechargeable Li metal batteries. Solid electrolytes with robust mechanical modulus are regarded as a promising approach to overcome the dendrite problems. However, their room-temperature ionic conductivities are usually too low to reach the level required for normal battery operation. Here, a class of novel solid electrolytes with liquid-like room-temperature ionic conductivities (> 1 mS cm-1) has been successfully synthesized by taking advantage of the unique nanoarchitectures of hollow silica (HS) spheres to confine liquid electrolytes in hollow space to afford high conductivities. In a symmetric lithium/lithium cell, such kind of solid-like electrolytes demonstrates a robust performance against Li dendrite problems, well stabilizing the cell system from short circuiting in a long-time operation at current densities ranging from 0.16 to 0.32 mA cm-2. Moreover, the high flexibility and compatibility of HS nanoarchitectures, in principle, enables broad tunability to choose desired liquids for the fabrication of other kinds of solid-like electrolytes, such as those containing Na+, Mg2+ or Al3+ as conductive media, providing a useful alternative strategy for the development of next generation rechargeable batteries.

  19. Accessing the bottleneck in all-solid state batteries, lithium-ion transport over the solid-electrolyte-electrode interface.

    Science.gov (United States)

    Yu, Chuang; Ganapathy, Swapna; Eck, Ernst R H van; Wang, Heng; Basak, Shibabrata; Li, Zhaolong; Wagemaker, Marnix

    2017-10-20

    Solid-state batteries potentially offer increased lithium-ion battery energy density and safety as required for large-scale production of electrical vehicles. One of the key challenges toward high-performance solid-state batteries is the large impedance posed by the electrode-electrolyte interface. However, direct assessment of the lithium-ion transport across realistic electrode-electrolyte interfaces is tedious. Here we report two-dimensional lithium-ion exchange NMR accessing the spontaneous lithium-ion transport, providing insight on the influence of electrode preparation and battery cycling on the lithium-ion transport over the interface between an argyrodite solid-electrolyte and a sulfide electrode. Interfacial conductivity is shown to depend strongly on the preparation method and demonstrated to drop dramatically after a few electrochemical (dis)charge cycles due to both losses in interfacial contact and increased diffusional barriers. The reported exchange NMR facilitates non-invasive and selective measurement of lithium-ion interfacial transport, providing insight that can guide the electrolyte-electrode interface design for future all-solid-state batteries.

  20. Stability of the solid electrolyte Li{sub 3}OBr to common battery solvents

    Energy Technology Data Exchange (ETDEWEB)

    Schroeder, D.J. [Department of Engineering Technology, College of Engineering and Engineering Technology, Northern Illinois University, 301B Still Gym, DeKalb, IL 60115 (United States); Hubaud, A.A. [Chemical Sciences and Engineering Division, Argonne National Laboratory, 9700 South Cass Avenue, Argonne, IL 60439-4837 (United States); Vaughey, J.T., E-mail: vaughey@anl.gov [Chemical Sciences and Engineering Division, Argonne National Laboratory, 9700 South Cass Avenue, Argonne, IL 60439-4837 (United States)

    2014-01-01

    Graphical abstract: The stability of the anti-perovskite phase Li{sub 3}OBr has been assessed in a variety of battery solvents. - Highlights: • Lithium stable solid electrolyte Li{sub 3}OBr unstable to polar organic solvents. • Solvation with no dissolution destroys long-range structure. • Ion exchange with protons observed. - Abstract: Recently a new class of solid lithium ion conductors was reported based on the anti-perovskite structure, notably Li{sub 3}OCl and Li{sub 3}OBr. For many beyond lithium-ion battery uses, the solid electrolyte is envisioned to be in direct contact with liquid electrolytes and lithium metal. In this study we evaluated the stability of the Li{sub 3}OBr phase against common battery solvents electrolytes, including diethylcarbonate (DEC) and dimethylcarbonate (DMC), as well as a LiPF{sub 6} containing commercial electrolyte. In contact with battery-grade organic solvents, Li{sub 3}OBr was typically found to be insoluble but lost its crystallinity and reacted with available protons and in some cases with the solvent. A low temperature heat treatment was able to restore crystallinity of the samples; however evidence of proton ion exchange was conserved.

  1. Performance of a novel type of electrolyte-supported solid oxide fuel cell with honeycomb structure

    Energy Technology Data Exchange (ETDEWEB)

    Ruiz-Morales, Juan Carlos; Savvin, Stanislav N.; Nunez, Pedro [Departmento de Quimica Inorganica, Universidad de La Laguna, 38200 Tenerife (Spain); Marrero-Lopez, David [Departamento de Fisica Aplicada I, Universidad de Malaga, 29071 Malaga (Spain); Pena-Martinez, Juan; Canales-Vazquez, Jesus [Instituto de Energias Renovables-Universidad de Castilla la Mancha, 02006 Albacete (Spain); Roa, Joan Josep; Segarra, Merce [DIOPMA, Departamento de Ciencia de los Materiales e Ing. Metalurgica, 08028 Barcelona (Spain)

    2010-01-15

    A novel design, alternative to the conventional electrolyte-supported solid oxide fuel cell (SOFC) is presented. In this new design, a honeycomb-electrolyte is fabricated from hexagonal cells, providing high mechanical strength to the whole structure and supporting the thin layer used as electrolyte of a SOFC. This new design allows a reduction of {proportional_to}70% of the electrolyte material and it renders modest performances over 320 mW cm{sup -2} but high volumetric power densities, i.e. 1.22 W cm{sup -3} under pure CH{sub 4} at 900 C, with a high OCV of 1.13 V, using the standard Ni-YSZ cermet as anode, Pt as cathode material and air as the oxidant gas. (author)

  2. Perovskite solid electrolytes: Structure, transport properties and fuel cell applications

    DEFF Research Database (Denmark)

    Bonanos, N.; Knight, K.S.; Ellis, B.

    1995-01-01

    Doped barium cerate perovskites, first investigated by Iwahara and co-workers, have ionic conductivities of the order of 20 mS/cm at 800 degrees C making them attractive as fuel cell electrolytes for this temperature region. They have been used to construct laboratory scale fuel cells, which...... vapour transfer in a cell in which the perovskite is exposed to wet hydrogen on both sides. The evolution of transport properties with temperature is discussed in relation to structure. Neutron diffraction studies of doped and undoped barium cerate are reported, revealing a series of phase transitions...

  3. Toward garnet electrolyte-based Li metal batteries: An ultrathin, highly effective, artificial solid-state electrolyte/metallic Li interface.

    Science.gov (United States)

    Fu, Kun Kelvin; Gong, Yunhui; Liu, Boyang; Zhu, Yizhou; Xu, Shaomao; Yao, Yonggang; Luo, Wei; Wang, Chengwei; Lacey, Steven D; Dai, Jiaqi; Chen, Yanan; Mo, Yifei; Wachsman, Eric; Hu, Liangbing

    2017-04-01

    Solid-state batteries are a promising option toward high energy and power densities due to the use of lithium (Li) metal as an anode. Among all solid electrolyte materials ranging from sulfides to oxides and oxynitrides, cubic garnet-type Li7La3Zr2O12 (LLZO) ceramic electrolytes are superior candidates because of their high ionic conductivity (10(-3) to 10(-4) S/cm) and good stability against Li metal. However, garnet solid electrolytes generally have poor contact with Li metal, which causes high resistance and uneven current distribution at the interface. To address this challenge, we demonstrate a strategy to engineer the garnet solid electrolyte and the Li metal interface by forming an intermediary Li-metal alloy, which changes the wettability of the garnet surface (lithiophobic to lithiophilic) and reduces the interface resistance by more than an order of magnitude: 950 ohm·cm(2) for the pristine garnet/Li and 75 ohm·cm(2) for the surface-engineered garnet/Li. Li7La2.75Ca0.25Zr1.75Nb0.25O12 (LLCZN) was selected as the solid-state electrolyte (SSE) in this work because of its low sintering temperature, stabilized cubic garnet phase, and high ionic conductivity. This low area-specific resistance enables a solid-state garnet SSE/Li metal configuration and promotes the development of a hybrid electrolyte system. The hybrid system uses the improved solid-state garnet SSE Li metal anode and a thin liquid electrolyte cathode interfacial layer. This work provides new ways to address the garnet SSE wetting issue against Li and get more stable cell performances based on the hybrid electrolyte system for Li-ion, Li-sulfur, and Li-oxygen batteries toward the next generation of Li metal batteries.

  4. Fluorine-Doped Antiperovskite Electrolyte for All-Solid-State Lithium-Ion Batteries.

    Science.gov (United States)

    Li, Yutao; Zhou, Weidong; Xin, Sen; Li, Shuai; Zhu, Jinlong; Lü, Xujie; Cui, Zhiming; Jia, Quanxi; Zhou, Jianshi; Zhao, Yusheng; Goodenough, John B

    2016-08-16

    A fluorine-doped antiperovskite Li-ion conductor Li2 (OH)X (X=Cl, Br) is shown to be a promising candidate for a solid electrolyte in an all-solid-state Li-ion rechargeable battery. Substitution of F(-) for OH(-) transforms orthorhombic Li2 OHCl to a room-temperature cubic phase, which shows electrochemical stability to 9 V versus Li(+) /Li and two orders of magnitude higher Li-ion conductivity than that of orthorhombic Li2 OHCl. An all-solid-state Li/LiFePO4 with F-doped Li2 OHCl as the solid electrolyte showed good cyclability and a high coulombic efficiency over 40 charge/discharge cycles. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  5. Novel Molecular Architectures Developed for Improved Solid Polymer Electrolytes for Lithium Polymer Batteries

    Science.gov (United States)

    Meador, Mary Ann B.; Kinder, James D.; Bennett, William R.

    2002-01-01

    Lithium-based polymer batteries for aerospace applications need the ability to operate in temperatures ranging from -70 to 70 C. Current state-of-the-art solid polymer electrolytes (based on amorphous polyethylene oxide, PEO) have acceptable ionic conductivities (10-4 to 10-3 S/cm) only above 60 C. Higher conductivity can be achieved in the current systems by adding solvent or plasticizers to the solid polymer to improve ion transport. However, this can compromise the dimensional and thermal stability of the electrolyte, as well as compatibility with electrode materials. One of NASA Glenn Research Center's objectives in the PERS program is to develop new electrolytes having unique molecular architectures and/or novel ion transport mechanisms, leading to good ionic conductivity at room temperature and below without solvents or plasticizers.

  6. Synthesis and characterization of γ-Bi2O3 based solid electrolyte ...

    Indian Academy of Sciences (India)

    Administrator

    3Chemistry Department, Art and Science Faculty, Nigde University, Nigde, Turkey. MS received 25 April 2013; revised 14 July 2013. Abstract. γ-phase bismuth oxide is a well known high oxygen ion conductor and can be used as an electrolyte for intermediate temperature solid oxide fuel cells (IT-SOFCs). This study aims to ...

  7. Fermi Potential across Working Solid Oxide Cells with Zirconia or Ceria Electrolytes

    DEFF Research Database (Denmark)

    Jacobsen, Torben; Chatzichristodoulou, Christodoulos; Mogensen, Mogens Bjerg

    2014-01-01

    observed for ceria based electrolytes, but also in case of solid oxide electrolyser cells (SOEC) with yttria stabilized zirconia (YSZ) big electronic leak currents have been observed for very high overvoltages on one or both electrodes. Furthermore, it is important to realize that the potential gradient...

  8. Proton-conducting solid acid electrolytes based upon MH(PO3H)

    NARCIS (Netherlands)

    Zhou, W.

    2011-01-01

    Solid acids, such as CsHSO4 and CsH2PO4, are a novel class of anhydrous proton-conducting compounds that can be used as electrolyte in H2/O2 and direct methanol fuel cells. The disordering of the hydrogen-bonded network above the so-called superprotonic phase transition results in an increase of the

  9. Electrocatalysis in Water Electrolysis with Solid Polymer Electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Rasten, Egil

    2001-10-01

    Development and optimization of the electrodes in a water electrolysis system using a polymer membrane as electrolyte have been carried out in this work. A cell voltage of 1.59 V (energy consumption of about 3.8 kWh/Nm{sub 3} H{sub 2}) has been obtained at practical operation conditions of the electrolysis cell (10 kA . m2, 90{sup o}C) using a total noble metal loading of less than 2.4 mg.cm{sub 2} and a Nafion -115 membrane. It is further shown that a cell voltage of less than 1.5 V is possible at the same conditions by combination of the best electrodes obtained in this work. The most important limitation of the electrolysis system using polymer membrane as electrolyte has proven to be the electrical conductivity of the catalysts due to the porous backing/current collector system, which increases the length of the current path and decreases the cross section compared to the apparent one. A careful compromise must therefore be obtained between electrical conductivity and active surface area, which can be tailored by preparation and annealing conditions of the metal oxide catalysts. Anode catalysts of different properties have been developed. The mixed oxide of Ir-Ta (85 mole% Ir) was found to exhibit highest voltage efficiency at a current density of 10 kA.m{sub 2} or below, whereas the mixed oxide of Ir and Ru (60-80 mole% Ir) was found to give the highest voltage efficiency for current densities of above 10 kA.m{sub 2}. Pt on carbon particles, was found to be less suitable as cathode catalyst in water electrolysis. The large carbon particles introduced an unnecessary porosity into the catalytic layer, which resulted in a high ohmic drop. Much better voltage efficiency was obtained by using Pt-black as cathode catalyst, which showed a far better electrical conductivity. Ru-oxide as cathode catalyst in water electrolysis systems using a polymer electrolyte was not found to be of particular interest due to insufficient electrochemical activity and too low

  10. The LiBH4-LiI Solid Solution as an Electrolyte in an All-Solid-State Battery

    DEFF Research Database (Denmark)

    Sveinbjörnsson, Dadi Þorsteinn; Christiansen, Ane Sælland; Viskinde, Rasmus

    2014-01-01

    is compared with a cell with an identical electrode setup but a liquid electrolyte (1 M LiPF6 in EC:DMC). All measurements were carried out at a temperature of 60°C. For the all-solid-state cells, 81% of the theoretical discharge capacity is reached for a discharge rate of 10 μA, but a capacity fade of 1......The charge and discharge performance of an all-solid-state lithium battery with the LiBH4-LiI solid solution as an electrolyte is reported. Lithium titanate (Li4Ti5O12) was used as the positive electrode and lithium metal as the negative electrode. The performance of the all-solid-state cell...... the change in the discharge capacity of the cells and changes in the cell impedance over 200 charge-discharge cycles. This is expectedly due to the possible formation of passivating areas in the cell and/or loss of contact area between the electrolyte and the electrodes....

  11. Carbon nanotubes-polyethylene oxide composite electrolyte for solid-state dye-sensitized solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Shaheer Akhtar, M. [School of Semiconductor and Chemical Engineering and Solar Energy Research Center, Chonbuk National University, Dukjin dong, Dukjin Gu, Jeonju, Jeonbuk 561-756 (Korea, Republic of); Department of Semiconductor Science and Technology, SPRC, Chonbuk National University, Jeonju, Jeonbuk 561-756 (Korea, Republic of); Park, Jung-Geun; Lee, Hyun-Cheol [School of Semiconductor and Chemical Engineering and Solar Energy Research Center, Chonbuk National University, Dukjin dong, Dukjin Gu, Jeonju, Jeonbuk 561-756 (Korea, Republic of); Lee, S.-K. [Department of Semiconductor Science and Technology, SPRC, Chonbuk National University, Jeonju, Jeonbuk 561-756 (Korea, Republic of); Yang, O-Bong, E-mail: obyang@chonbuk.ac.k [School of Semiconductor and Chemical Engineering and Solar Energy Research Center, Chonbuk National University, Dukjin dong, Dukjin Gu, Jeonju, Jeonbuk 561-756 (Korea, Republic of)

    2010-02-28

    Novel carbon nanotubes (CNTs)-polyethylene oxide (PEO) composite electrolyte for dye-sensitized solar cell (DSSC) was prepared and characterized for the first time. The strong bonding and interaction between CNTs and PEO in CNTs-PEO composites was observed by the characterization of X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and Raman spectra. The introduction of CNTs into PEO matrix significantly improved the electrolyte properties of DSSC such as roughness, amorphicity and ionic conductivity. The solid-state DSSC fabricated with the optimum composite electrolyte (added 1% CNTs in PEO matrix, 1%CNT-PEO) achieved maximum conversion efficiency of 3.5%, an open circuit voltage (V{sub OC}) of 0.589 V, short circuit current density (J{sub SC}) of 10.64 mA/cm{sup 2} and fill factor (FF) of 56%. The highest IPCE in the DSSC fabricated with 1%CNT-PEO electrolyte is ascribed to the improved ionic conductivity of composite electrolytes and enhanced interfacial contact between electrode and electrolyte.

  12. Ionic and electronic transport across interfaces in thin electrolyte film, anode supported solid oxide fuel cells

    Science.gov (United States)

    Lim, Hyung-Tae

    In transport studies in oxygen ion conductors, oxygen chemical potential (muO2) has been usually assumed to be equilibrated across gas/solid electrolyte interfaces. However, since the interfaces exhibit different properties from the bulk, they must have their own ionic and electronic properties. In this study, Pt reference electrodes were embedded within the electrolyte (gadolinia-doped ceria; GDC) in an anode-supported solid oxide fuel cell to measure the electrochemical potential of electrons (ϕ) through the bulk electrolyte and its interfaces under fuel cell operating condition. Based on local equilibrium assumption, which leads to relations between electrochemical potentials of charged species and chemical potential of neutral species, the corresponding mu O2 was estimated. When the GDC is protected by a thin layer of a predominantly ionic conductor from reducing atmosphere, the muO2 varied monotonically through the GDC layer, exhibiting a relatively small change across the cathode interface region. By contrast, when the GDC was exposed to hydrogen, it was significantly reduced, resulting in higher electron concentration. The corresponding mu O2 was small through the GDC layer, exhibiting an abrupt change across the cathode interface region. This difference in the muO2 variation depending upon the relative electronic conduction in the electrolyte resulted in a large difference in the cathode overpotential. The direction of ionic/electronic current and the corresponding internal muO2 through the electrolyte can have a profound effect on its stability. If cell imbalance exists in a series-connected fuel cell stack, a "bad" cell characterized by a higher resistance can be operated under a negative voltage. To investigate the SOFC stack failure by simulating abnormal behavior in a single cell test, yttira stabilized zirconia (YSZ) electrolyte cells were tested with an applied DC bias. When operating under a negative voltage, rapid degradation occurred

  13. Correlating the interface resistance and surface adhesion of the Li metal-solid electrolyte interface

    Science.gov (United States)

    Wang, Michael; Sakamoto, Jeff

    2018-02-01

    Solid electrolytes could enable stable cycling of metallic Li anodes, which can offer drastic increases to the capacity of Li-ion batteries. However, little is known about the mechanics of the Li-solid electrolyte interface. This study combines electrochemical and mechanical characterization to correlate interface kinetics with adhesive strength. Cubic garnet with the Li6·25Al0·25La3Zr2O12 (LLZO) formulation was selected as a model solid electrolyte based on its high conductivity and stability against Li metal. Symmetric Li-LLZO cells were tested using electrochemical impedance spectroscopy to determine the interfacial resistance, Rint, and the adhesive strength of the Li-LLZO interface, σadh, was measured using a unique tensile test in an inert atmosphere. It was determined that the Rint is directly correlated to the adhesive strength of Li on LLZO. At the highest Rint in this study, 330 k·cm2 the σadh was 1.1 kPa and at the lowest Rint in this study, 7 ·cm2, σadh was 8 MPa. Furthermore, by optimizing the surface chemistry the wettability of LLZO was enhanced resulting in σadh exceeding the ultimate tensile strength of Li metal. The relationship demonstrated provides a deeper understanding of the mechanical properties of the Li-electrolyte interface, which will play an important role in the design of batteries employing metallic Li anodes.

  14. A solid ceramic electrolyte system for measuring redox conditions in high temperature gas mixing studies

    Science.gov (United States)

    Williams, R. J.

    1972-01-01

    The details of the construction and operation of a gas mixing furnace are presented. A solid ceramic oxygen electrolyte cell is used to monitor the oxygen fugacity in the furnace. The system consists of a standard vertical-quench, gas mixing furnace with heads designed for mounting the electrolyte cell and with facilities for inserting and removing the samples. The system also contains the highinput impedance electronics necessary for measurements and a simplified version of standard gas mixing apparatus. The calibration and maintenance of the system are discussed.

  15. Stability of thin layer electrodeposited copper in solid polymer electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Atchia, S. (Lab. d' Ionique et d' Electrochimie des Solides de Grenoble, I.N.P.G.-E.N.S.E.E.G., 38 - St. Martin d' Heres (France)); Deroo, D. (Lab. d' Ionique et d' Electrochimie des Solides de Grenoble, I.N.P.G.-E.N.S.E.E.G., 38 - St. Martin d' Heres (France)); Petit, J.P. (Lab. d' Ionique et d' Electrochimie des Solides de Grenoble, I.N.P.G.-E.N.S.E.E.G., 38 - St. Martin d' Heres (France)); Armand, M. (Lab. d' Ionique et d' Electrochimie des Solides de Grenoble, I.N.P.G.-E.N.S.E.E.G., 38 - St. Martin d' Heres (France)); Rosman, N. (Lab. d' Ionique et d' Electrochimie des Solides de Grenoble, I.N.P.G.-E.N.S.E.E.G., 38 - St. Martin d' Heres (France))

    1993-03-01

    In the course of our studies on variable reflection windows involving copper deposition, we have proposed to use P(EO)[sub n]KCu[sub x]I[sub 1+x] complexes. The excess I[sup -] ions stabilizes copper (I) through formation of CuI[sub n+1][sup n-] and the transport of copper is solely due to the diffusion of anionic complexes which acts as copper vehicles. Copper electrodeposition has been observed. The stripping of the copper layers strongly depends upon the relaxation time between the copper plating and the beginning of the anodic voltametric scan. The copper deposit slowly vanishes with time. A cathodic current is observed before the copper plating process which we relate to the possible reduction of an oxidizing species present in the electrolyte. The search for such oxidizing species (Cu[sup 2+], I[sub 3][sup -]) has been made using ESR and Raman spectroscopy and we have shown the presence of I[sub 3][sup -]. (orig.)

  16. Development of sulfide solid electrolytes and interface formation processes for bulk-type all-solid-state Li and Na batteries

    Directory of Open Access Journals (Sweden)

    Akitoshi Hayashi

    2016-07-01

    Full Text Available All-solid-state batteries with inorganic solid electrolytes are recognized as an ultimate goal of rechargeable batteries because of their high safety, versatile geometry and good cycle life. Compared to thin-film batteries, increasing the reversible capacity of bulk-type all-solid-state batteries using electrode active material particles is difficult because contact areas at solid–solid interfaces between the electrode and electrolyte particles are limited. Sulfide solid electrolytes have several advantages of high conductivity, wide electrochemical window, and appropriate mechanical properties such as formability, processability, and elastic modulus. Sulfide electrolyte with Li7P3S11 crystal has the highest Li+ ion conductivity of 1.7 × 10-2 S cm-1 at 25 °C. It is far beyond the Li+ ion conductivity of conventional organic liquid electrolytes. The Na+ ion conductivity of 7.4 × 10-4 S cm-1 is achieved for Na3.06P0.94Si0.06S4 with cubic structure. Moreover, formation of favorable solid–solid interfaces between electrode and electrolyte is important for realizing solid-state batteries. Sulfide electrolytes have better formability than oxide electrolytes. Consequently, a dense electrolyte separator and closely attached interfaces with active material particles are achieved via room-temperature sintering of sulfides merely by cold pressing without heat treatment. Elastic moduli for sulfide electrolytes are smaller than that of oxide electrolytes, and Na2S-P2S5 glass electrolytes have smaller Young’s modulus than Li2S-P2S5 electrolytes. Cross-sectional SEM observations for a positive electrode layer reveal that sulfide electrolyte coating on active material particles increases interface areas even with a minimum volume of electrolyte, indicating that the energy density of bulk-type solid-state batteries is enhanced. Both surface coating of electrode particles and preparation of nanocomposite are effective for increasing the reversible

  17. Further studies on the lithium phosphorus oxynitride solid electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Pichonat, Tristan [Institut d' Electronique, de Microelectronique et de Nanotechnologie (IEMN), Universite Lille 1, CNRS UMR 8520 Avenue Poincare, BP 60069, 59652 Villeneuve d' Ascq cedex (France); Institut de Recherche sur les Composants logiciels et materiels pour l' Information et la Communication Avancee (IRCICA), Universite Lille 1, CNRS FR 3024, Parc Scientifique de la Haute Borne, 50 Avenue Halley, 59650 Villeneuve d' Ascq (France); Lethien, Christophe, E-mail: christophe.lethien@iemn.univ-lille1.fr [Institut d' Electronique, de Microelectronique et de Nanotechnologie (IEMN), Universite Lille 1, CNRS UMR 8520 Avenue Poincare, BP 60069, 59652 Villeneuve d' Ascq cedex (France); Institut de Recherche sur les Composants logiciels et materiels pour l' Information et la Communication Avancee (IRCICA), Universite Lille 1, CNRS FR 3024, Parc Scientifique de la Haute Borne, 50 Avenue Halley, 59650 Villeneuve d' Ascq (France); Tiercelin, Nicolas; Godey, Sylvie [Institut d' Electronique, de Microelectronique et de Nanotechnologie (IEMN), Universite Lille 1, CNRS UMR 8520 Avenue Poincare, BP 60069, 59652 Villeneuve d' Ascq cedex (France); Pichonat, Emmanuelle [Laboratoire de Spectrochimie Infrarouge et Raman (LASIR), CNRS UMR 8516, Universite Lille 1, 59655 Villeneuve d' Ascq Cedex (France); Roussel, Pascal; Colmont, Marie [Unite de Catalyse et de Chimie du Solide (UCCS), CNRS UMR 8181, Universite Lille 1, 59655 Villeneuve d' Ascq Cedex (France); Rolland, Paul Alain [Institut d' Electronique, de Microelectronique et de Nanotechnologie (IEMN), Universite Lille 1, CNRS UMR 8520 Avenue Poincare, BP 60069, 59652 Villeneuve d' Ascq cedex (France); Institut de Recherche sur les Composants logiciels et materiels pour l' Information et la Communication Avancee (IRCICA), Universite Lille 1, CNRS FR 3024, Parc Scientifique de la Haute Borne, 50 Avenue Halley, 59650 Villeneuve d' Ascq (France)

    2010-09-01

    First step in the way to the fabrication of an all-solid microbattery for autonomous wireless sensor node, amorphous thin solid films of lithium phosphorus oxynitride (LiPON) were prepared by radio-frequency sputtering of a mixture target of P{sub 2}O{sub 5}/Li{sub 2}O in ambient nitrogen atmosphere. The morphology, composition, and ionic conductivity were characterized by scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy, and A.C. impedance spectroscopy. With a thickness of 1.4 {mu}m, the obtained LiPON amorphous layer provided an ionic conductivity close to 6 x 10{sup -7} S cm{sup -1} at room temperature. MicroRaman UV spectroscopy study was successfully carried out for the first time on LiPON thin films to complete the characterization and bring further information on LiPON structure.

  18. Semiconductor/solid electrolyte junctions for optical information storage. Solid-state electrochromic cell using lutecium diphthalocyanine

    Science.gov (United States)

    Sammells, A. F.; Pujare, N. U.

    1986-01-01

    The overall program goal is to perform a basic investigation of photoelectrochemical and electrochemical effects by electrochromic materials in solid polymer electrolyte (SPE) containing solid-state cells. Initial investigations have been directed towards reversible electrochromic behavior at the interface between lutecium diphthalocyanine deposited onto electronically conducting glass, and the homopolymer poly-2-acrylamido -2-methylpropane sulfonic acid (poly(Amps)). We wish to report here some recent work on solid-state electrochromic cells in which ionic mediation to thin-film deposits of lutecium diphthalocyanine is via the homopolymer poly-2-acrylamido-2-methyl propane sulfonic acid (poly-Amps). Separation between the working (LuH(Pc)2 deposited onto SnO2 conducting glass) and counter (CeCl3 in poly (Amps)) electrodes in these solid-state cells was realized by the use of the insoluble copolymer perfluorosulfonic acid (Nafion). Solid-state electrochromic cells were prepared using the supporting electrolytes (SEs) 0.1M Na2SO4 and 0.1M KCl. Upon subjecting the cell to anodic and cathodic voltage scans, up to four distinct color changes were observed varying from red (at anodic potentials) to violet (at cathodic potentials). Formation of the violet lutecium diphthalocyanine reduction product was not found contingent upon the absence of alkali cations as reported by others.

  19. Bendable and thin sulfide solid electrolyte film: a new electrolyte opportunity for free-standing and stackable high-energy all-solid-state lithium-ion batteries.

    Science.gov (United States)

    Nam, Young Jin; Cho, Sung-Ju; Oh, Dae Yang; Lim, Jun-Muk; Kim, Sung Youb; Song, Jun Ho; Lee, Young-Gi; Lee, Sang-Young; Jung, Yoon Seok

    2015-05-13

    Bulk-type all-solid-state lithium batteries (ASLBs) are considered a promising candidate to outperform the conventional lithium-ion batteries. Unfortunately, the current technology level of ASLBs is in a stage of infancy in terms of cell-based (not electrode-material-based) energy densities and scalable fabrication. Here, we report on the first ever bendable and thin sulfide solid electrolyte films reinforced with a mechanically compliant poly(paraphenylene terephthalamide) nonwoven (NW) scaffold, which enables the fabrication of free-standing and stackable ASLBs with high energy density and high rate capabilities. The ASLB, using a thin (∼70 μm) NW-reinforced SE film, exhibits a 3-fold increase of the cell-energy-density compared to that of a conventional cell without the NW scaffold.

  20. Fabrication method for solid electrolyte fuel cell. Kotai denkaishitsu nenryo denchi no seizo hoho

    Energy Technology Data Exchange (ETDEWEB)

    Inoue, Y.; Kuru, N.; Uchida, S.

    1993-01-29

    In general, CaO stabilized ZrO2, NiO, Y2O3 stabilized ZrO2, and LaCoO3 are used for the substrate tube, fuel electrode, electrolyte and air electrode respectively in the solid oxide electrolyte fuel cell (SOFC). When SOFC generates power at approximately 1,000[degree]C, NiO of the fuel electrode is reduced to become Ni, tensile stress is produced at the fuel electrode at this time, and cracks produced in the fuel electrode propagate to the electrolyte and the air electrode, with a possibility of damaging the entire SOFC. According to this invention, a film of NiO which is the material for the fuel electrode is formed on the substrate tube which is then subjected to heat treatment to reduce NiO to Ni, and the electrolyte and the air electrode are laminated successively. By reduction heat treatment after the formation of the NiO fuel electrode, crack propagation from the fuel electrode to the electrolyte and the fuel electrode can be prevented even if hydrogen is flown during power generation because no NiO-Ni reaction occurs at the fuel electrode. 7 figs.

  1. Flexible thin-film battery based on solid-like ionic liquid-polymer electrolyte

    Science.gov (United States)

    Li, Qin; Ardebili, Haleh

    2016-01-01

    The development of high-performance flexible batteries is imperative for several contemporary applications including flexible electronics, wearable sensors and implantable medical devices. However, traditional organic liquid-based electrolytes are not ideal for flexible batteries due to their inherent safety and stability issues. In this study, a non-volatile, non-flammable and safe ionic liquid (IL)-based polymer electrolyte film with solid-like feature is fabricated and incorporated in a flexible lithium ion battery. The ionic liquid is 1-Ethyl-3-methylimidazolium dicyanamide (EMIMDCA) and the polymer is composed of poly(vinylidene fluoride-co-hexafluoropropene) (PVDF-HFP). The electrolyte exhibits good thermal stability (i.e. no weight loss up to 300 °C) and relatively high ionic conductivity (6 × 10-4 S cm-1). The flexible thin-film lithium ion battery based on solid-like electrolyte film is encapsulated using a thermal-lamination process and demonstrates excellent electrochemical performance, in both flat and bent configurations.

  2. Composite electrolyte with proton conductivity for low-temperature solid oxide fuel cell

    Energy Technology Data Exchange (ETDEWEB)

    Raza, Rizwan, E-mail: razahussaini786@gmail.com [Department of Physics, COMSATS Institute of Information Technology, Lahore 54000 (Pakistan); Department of Energy Technology, Royal Institute of Technology, KTH, Stockholm 10044 (Sweden); Ahmed, Akhlaq; Akram, Nadeem; Saleem, Muhammad; Niaz Akhtar, Majid; Ajmal Khan, M.; Abbas, Ghazanfar; Alvi, Farah; Yasir Rafique, M. [Department of Physics, COMSATS Institute of Information Technology, Lahore 54000 (Pakistan); Sherazi, Tauqir A. [Department of Chemistry, COMSATS Institute of Information Technology, Abbotabad 22060 (Pakistan); Shakir, Imran [Sustainable Energy Technologies (SET) center, College of Engineering, King Saud University, PO-BOX 800, Riyadh 11421 (Saudi Arabia); Mohsin, Munazza [Department of Physics, Lahore College for Women University, Lahore, 54000 (Pakistan); Javed, Muhammad Sufyan [Department of Physics, COMSATS Institute of Information Technology, Lahore 54000 (Pakistan); Department of Applied Physics, Chongqing University, Chongqing 400044 (China); Zhu, Bin, E-mail: binzhu@kth.se, E-mail: zhubin@hubu.edu.cn [Department of Energy Technology, Royal Institute of Technology, KTH, Stockholm 10044 (Sweden); Hubei Collaborative Innovation Center for Advanced Organic Chemical Materials, Faculty of Physics and Electronic Science/Faculty of Computer and Information, Hubei University, Wuhan, Hubei 430062 (China)

    2015-11-02

    In the present work, cost-effective nanocomposite electrolyte (Ba-SDC) oxide is developed for efficient low-temperature solid oxide fuel cells (LTSOFCs). Analysis has shown that dual phase conduction of O{sup −2} (oxygen ions) and H{sup +} (protons) plays a significant role in the development of advanced LTSOFCs. Comparatively high proton ion conductivity (0.19 s/cm) for LTSOFCs was achieved at low temperature (460 °C). In this article, the ionic conduction behaviour of LTSOFCs is explained by carrying out electrochemical impedance spectroscopy measurements. Further, the phase and structure analysis are investigated by X-ray diffraction and scanning electron microscopy techniques. Finally, we achieved an ionic transport number of the composite electrolyte for LTSOFCs as high as 0.95 and energy and power density of 90% and 550 mW/cm{sup 2}, respectively, after sintering the composite electrolyte at 800 °C for 4 h, which is promising. Our current effort toward the development of an efficient, green, low-temperature solid oxide fuel cell with the incorporation of high proton conductivity composite electrolyte may open frontiers in the fields of energy and fuel cell technology.

  3. Super Soft All-Ethylene Oxide Polymer Electrolyte for Safe All-Solid Lithium Batteries

    Science.gov (United States)

    Porcarelli, Luca; Gerbaldi, Claudio; Bella, Federico; Nair, Jijeesh Ravi

    2016-01-01

    Here we demonstrate that by regulating the mobility of classic −EO− based backbones, an innovative polymer electrolyte system can be architectured. This polymer electrolyte allows the construction of all solid lithium-based polymer cells having outstanding cycling behaviour in terms of rate capability and stability over a wide range of operating temperatures. Polymer electrolytes are obtained by UV-induced (co)polymerization, which promotes an effective interlinking between the polyethylene oxide (PEO) chains plasticized by tetraglyme at various lithium salt concentrations. The polymer networks exhibit sterling mechanical robustness, high flexibility, homogeneous and highly amorphous characteristics. Ambient temperature ionic conductivity values exceeding 0.1 mS cm−1 are obtained, along with a wide electrochemical stability window (>5 V vs. Li/Li+), excellent lithium ion transference number (>0.6) as well as interfacial stability. Moreover, the efficacious resistance to lithium dendrite nucleation and growth postulates the implementation of these polymer electrolytes in next generation of all-solid Li-metal batteries working at ambient conditions. PMID:26791572

  4. Atomic Layer Deposition of the Solid Electrolyte Garnet Li7La3Zr2O12

    Energy Technology Data Exchange (ETDEWEB)

    Kazyak, Eric; Chen, Kuan-Hung; Wood, Kevin N.; Davis, Andrew L.; Thompson, Travis; Bielinski, Ashley R.; Sanchez, Adrian; Wang, Xiang; Wang, Chongmin; Sakamoto, Jeff S.; Dasgupta, Neil P.

    2017-04-25

    Lithium solid electrolytes are a promising platform for achieving high energy density, long-lasting, and safe rechargeable batteries, which could have widespread societal impact. In particular, the ceramic oxide garnet Li7La3Zr2O12 (LLZO) has been shown to be a promising electrolyte due to its stability and high ionic conductivity. Two major challenges for commercialization are manufacturing of thin layers and creating stable, low-impedance, interfaces with both anode and cathode materials. Atomic Layer Deposition (ALD) has recently been shown as a potential method for depositing both solid electrolytes and interfacial layers to improve the stability and performance at electrode-electrolyte interfaces in battery systems. Herein we present the first reported ALD process for LLZO, demonstrating the ability to tune composition within the amorphous film and anneal to achieve the desired cubic garnet phase. Formation of the cubic phase was observed at temperatures as low as 555°C, significantly lower than is required for bulk processing. Additionally, challenges associated with achieving a dense garnet phase due to substrate reactivity, morphology changes and Li loss under the necessary high temperature annealing are quantified via in situ synchrotron diffraction.

  5. Super Soft All-Ethylene Oxide Polymer Electrolyte for Safe All-Solid Lithium Batteries.

    Science.gov (United States)

    Porcarelli, Luca; Gerbaldi, Claudio; Bella, Federico; Nair, Jijeesh Ravi

    2016-01-21

    Here we demonstrate that by regulating the mobility of classic -EO- based backbones, an innovative polymer electrolyte system can be architectured. This polymer electrolyte allows the construction of all solid lithium-based polymer cells having outstanding cycling behaviour in terms of rate capability and stability over a wide range of operating temperatures. Polymer electrolytes are obtained by UV-induced (co)polymerization, which promotes an effective interlinking between the polyethylene oxide (PEO) chains plasticized by tetraglyme at various lithium salt concentrations. The polymer networks exhibit sterling mechanical robustness, high flexibility, homogeneous and highly amorphous characteristics. Ambient temperature ionic conductivity values exceeding 0.1 mS cm(-1) are obtained, along with a wide electrochemical stability window (>5 V vs. Li/Li(+)), excellent lithium ion transference number (>0.6) as well as interfacial stability. Moreover, the efficacious resistance to lithium dendrite nucleation and growth postulates the implementation of these polymer electrolytes in next generation of all-solid Li-metal batteries working at ambient conditions.

  6. Producing Gas-selective Electrochemical Microsensors by Tuning Solid Electrolyte Composition

    Directory of Open Access Journals (Sweden)

    1Erika SHOEMAKER ELLIS

    2008-10-01

    Full Text Available Abstract: Monolithic gas sensors, developed at Argonne National Laboratory, employed cyclic voltammetry measurement techniques, YSZ solid electrolyte electrochemical cells and K-nearest neighbor (neural chemometrics techniques to sense multiple components in a gas mixture. These voltammetry-based devices detected most hydrocarbons, displayed no saturation effects and were functional from < 1 ppm to 100 % oxygen concentrations, but were not sensitive to carbon dioxide due to the lack of reactivity within the Pt electrodes. Investigations revealed that specific CO2 sensitivity could be introduced by adding tungsten stabilized bismuth oxide (WBO to the solid electrolyte composition while maintaining the same basic sensor geometry and electrode configuration. The YSZ/WBO sensors are functional in a range of CO2 concentrations from low ppm to 100 %.

  7. Determination of oxygen in fusible metals by use of solid electrolyte cells.

    Science.gov (United States)

    Kunin, L L; Bogdanov, A A; Rodionov, V I

    1987-01-01

    A new method has been devised for determination of oxygen in fusible metals and compounds based on them, viz., by electrochemical extraction of oxygen with the help of a specially designed solid electrolyte cell. The physiocochemical conditions for the method to be used, and the analytical characteristics, are discussed. Results are given for determination of oxygen in a number of high-purity fusible metals. The relative standard deviation is inversely proportional to the mean oxygen concentration in the sample.

  8. Potential of polymethacrylate pseudo crown ethers as solid state polymer electrolytes.

    Science.gov (United States)

    Moins, S; Martins, J C; Krumpmann, A; Lemaur, V; Cornil, J; Delbosc, N; Decroly, A; Dubois, Ph; Lazzaroni, R; Gohy, J-F; Coulembier, O

    2017-06-22

    The association of kinetic studies, DFT calculations and 1 H- 7 Li NMR analyses allowed the control of the cyclo-ATRP of PEG 9 DMA and the production of polymethacrylate pseudo crown-ethers of various molar masses. Their potential to act as a solid-state polymer electrolyte in Li-ion batteries has been highlighted and may come from the supramolecular organization of the cyclo-PEG forming a Li + diffusion channel.

  9. Modifying zirconia solid electrolyte surface property to enhance oxide transport

    Energy Technology Data Exchange (ETDEWEB)

    Liaw, B.Y.; Song, S.Y. [Univ. of Hawaii, Honolulu, HI (United States)

    1996-12-31

    Bismuth-strontium-calcium-copper oxide (Bi{sub 2}Sr{sub 2}CaCu{sub 2}O{sub 8}, BSCCO) is known for its high T{sub c} superconducting behavior and mixed conducting property. The applicability of similar high T{sub c} cuprates for intermediate-temperature solid oxide fuel cell (SOFC) application has been studied recently. We investigated the electrochemical behavior of several Ag{vert_bar}BSCCO{vert_bar}10 mol% yttria-stabilized zirconia (YSZ){vert_bar}Ag and Ag{vert_bar}YSZ{vert_bar}Ag cells using complex impedance spectroscopy. A highly uniform and porous microstructure was observed at the interface of the YSZ and BSCCO. The ionic conductivity determined from the Nyquest plots in the temperature range of 200-700{degrees}C agrees with the values reported in the literature. The specific resistance of the BSCCO{vert_bar}YSZ interface was also determined to be lower than those of the conventional manganite electrode, suggesting that BSCCO seems attractive for cathode applications in SOFC.

  10. The conductivity and stability of polymer composite solid electrolyte upon addition of graphene

    Science.gov (United States)

    Hamid, Farzana Abd.; Salleh, Fauzani Md.; Mohamed, Nor Sabirin

    2017-12-01

    The effect of graphene composition on the conductivity and stability of polymer composite solid electrolyte was studied. These polymer composite solid electrolytes were synthesized by sol gel method and prepared via the solution-casting technique. The compositions of graphene were varied between 10 wt% to 70 wt%. The changes in the functional group of polymer composite after the addition of graphene were characterized by Fourier Transform InfraRed spectroscopy. Electrochemical impedance spectroscopy was conducted at ambient temperature in the frequency range of 10 Hz to 1 MHz to study the conductivity of the polymer composite. The highest conductivity was obtained at 60 wt% graphene with the value of 2.85×10-4 Scm-1. Sample without the addition of graphene showed the lowest conductivity value of 1.77×10-7 Scm-1 and acts as an insulator. The high conductivity at 60 wt% graphene loading is related to dehydration of cellulose. This is supported by the FTIR spectrum where the absorption peaks of C-O stretching vibrations of polymer composite is weakened and the hydroxyl group is slightly shifted compared to the FTIR spectrum without the addition of graphene. Linear sweep voltammetry results demonstrated that the polymer composite solid electrolyte exhibited electrochemical stability up to 3.2 V.

  11. Random-network simulation of an ultracapacitor based on metal-solid-electrolyte composite

    Science.gov (United States)

    Abel, J.; Kornyshev, A. A.

    1996-09-01

    A random-network model of a dense (pore-free) metal-solid-electrolyte composite is developed. Real and imaginary parts of admittance are simulated as a function of frequency and composition by means of the transfer matrix algorithm on a cubic lattice. For a composite without a solid-electrolyte membrane in the middle (insulating with respect to electronic current) the results predict the capacity maximum at the percolation threshold in three dimensions and two maxima in two dimensions as a function of composition; they are compared with the predictions of the effective medium theory. For a composite with an insulating membrane in the middle, typical for ultracapacitors, the maximum of capacitance in three dimensions is at equal portion of metal and solid-electrolyte particles. In contrast to metal dielectric mixtures there are no giant enhancement effects in static capacitance as a function of composition: the upper estimates of the enhancement factor are proportional to the ratio of the size of the sample to the size of the grains.

  12. Polymerizable Ionic Liquid Crystals Comprising Polyoxometalate Clusters toward Inorganic-Organic Hybrid Solid Electrolytes

    Directory of Open Access Journals (Sweden)

    Takeru Ito

    2017-07-01

    Full Text Available Solid electrolytes are crucial materials for lithium-ion or fuel-cell battery technology due to their structural stability and easiness for handling. Emergence of high conductivity in solid electrolytes requires precise control of the composition and structure. A promising strategy toward highly-conductive solid electrolytes is employing a thermally-stable inorganic component and a structurally-flexible organic moiety to construct inorganic-organic hybrid materials. Ionic liquids as the organic component will be advantageous for the emergence of high conductivity, and polyoxometalate, such as heteropolyacids, are well-known as inorganic proton conductors. Here, newly-designed ionic liquid imidazolium cations, having a polymerizable methacryl group (denoted as MAImC1, were successfully hybridized with heteropolyanions of [PW12O40]3− (PW12 to form inorganic-organic hybrid monomers of MAImC1-PW12. The synthetic procedure of MAImC1-PW12 was a simple ion-exchange reaction, being generally applicable to several polyoxometalates, in principle. MAImC1-PW12 was obtained as single crystals, and its molecular and crystal structures were clearly revealed. Additionally, the hybrid monomer of MAImC1-PW12 was polymerized by a radical polymerization using AIBN as an initiator. Some of the resulting inorganic-organic hybrid polymers exhibited conductivity of 10−4 S·cm−1 order under humidified conditions at 313 K.

  13. Compositional effect investigation by addition PEG, PEO plasticiser of LiBOB based solid polymer electrolyte for lithium ion batteries

    Science.gov (United States)

    Sabrina, Qolby; Ratri, Christin Rina

    2017-08-01

    Development polymer electrolyte with high ionic conductivity is main of object in solid state electrolyte will be potential application as electrolyte batteries. Casting method have been used to prepared solid polymer electrolyte. Adding polyethylene(glycol) PEG and Poly(ethylene oxide) PEO as polymer matrix be made of poly(vinylidene fluoride) (PVdF) and lithium bis(oxalato) borate (LiBOB) to improve structure morphology and impedance characterization of solid electrolyte. The ratio of PEG and PEO is varied to study effect on the conductivity. Electro impedance spectroscopy (EIS) studies are carried out on the prepared samples. The impedance measurement show that the conductivity with composition PVdF- PEG- LiBOB 10% better than the other varieties to applied as solid electrolyte batteries. SEM morphology PVdF- PEG- LiBOB 10% sample showed the low crystallinity was caused by interaction between lithium salt and polymer. With their properties the solid polymer electrolyte are considered as promising candidates of applications for lithium ion batteries.

  14. Impedance spectroscopy of ceramic solid electrolytes; Espectroscopia de impedancia de eletrolitos solidos ceramicos

    Energy Technology Data Exchange (ETDEWEB)

    Muccillo, R.; Cosentino, I.C.; Florio, D.Z. de; Franca, Y.V. [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil). Dept. de Engenharia de Materiais

    1996-12-31

    The Impedance Spectroscopy (IS) technique has been used to the study of Th O{sub 2}:Y{sub 2} O{sub 3}, Zr O{sub 2}:La{sub 2} O{sub 3} and Zr O{sub 2}:Y{sub 2} O{sub 3} solid electrolytes. The results show that solid solution has been attained, grain boundaries act as oxygen-ion blockers, and the importance of the IS technique to study phase transformation in ceramics. (author) 6 refs., 6 figs.

  15. Study on Zinc Oxide-Based Electrolytes in Low-Temperature Solid Oxide Fuel Cells.

    Science.gov (United States)

    Xia, Chen; Qiao, Zheng; Feng, Chu; Kim, Jung-Sik; Wang, Baoyuan; Zhu, Bin

    2017-12-28

    Semiconducting-ionic conductors have been recently described as excellent electrolyte membranes for low-temperature operation solid oxide fuel cells (LT-SOFCs). In the present work, two new functional materials based on zinc oxide (ZnO)-a legacy material in semiconductors but exceptionally novel to solid state ionics-are developed as membranes in SOFCs for the first time. The proposed ZnO and ZnO-LCP (La/Pr doped CeO₂) electrolytes are respectively sandwiched between two Ni 0.8 Co 0.15 Al 0.05 Li-oxide (NCAL) electrodes to construct fuel cell devices. The assembled ZnO fuel cell demonstrates encouraging power outputs of 158-482 mW cm -2 and high open circuit voltages (OCVs) of 1-1.06 V at 450-550 °C, while the ZnO-LCP cell delivers significantly enhanced performance with maximum power density of 864 mW cm -2 and OCV of 1.07 V at 550 °C. The conductive properties of the materials are investigated. As a consequence, the ZnO electrolyte and ZnO-LCP composite exhibit extraordinary ionic conductivities of 0.09 and 0.156 S cm -1 at 550 °C, respectively, and the proton conductive behavior of ZnO is verified. Furthermore, performance enhancement of the ZnO-LCP cell is studied by electrochemical impedance spectroscopy (EIS), which is found to be as a result of the significantly reduced grain boundary and electrode polarization resistances. These findings indicate that ZnO is a highly promising alternative semiconducting-ionic membrane to replace the electrolyte materials for advanced LT-SOFCs, which in turn provides a new strategic pathway for the future development of electrolytes.

  16. Production method of solid electrolyte fuel cell; Kotai denkaishitsu nenryo denchi no seizo hoho

    Energy Technology Data Exchange (ETDEWEB)

    Nagata, K.; Kuru, C.

    1995-09-05

    In the conventional cylindrical type laterally grooved solid electrolyte fuel cell (SOFC), the interconnector is thermally sprayed on the electrolyte. Since it is difficult to form a dense interconnector film by thermal spraying, the sealing film is applied underneath the interconnector to prevent the fuel gas from leaking. This invention solves the problem. The interconnector film is formed by means of thermal spraying on the substrate tube before film formation of fuel electrode and electrolyte on the substrate tube. Then it is heat-treated at 1300{degree}C for 2 hours to make the interconnector and the electrolyte dense at the same time. Since then the air electrode film is formed to complete the cylindrical type laterally grooved SOFC. This method can eliminate the sealing film, or the intermediate film, which is required in the conventional fuel cell structure. So that the production process can be simplified remarkably to reduce the production cost. In addition, the heat treatment stabilizes the physical properties of interconnector film. 2 figs.

  17. Structural, Thermal, and Electrical Properties of PVA-Sodium Salicylate Solid Composite Polymer Electrolyte

    Directory of Open Access Journals (Sweden)

    Noorhanim Ahad

    2012-01-01

    Full Text Available Structural, thermal, and electrical properties of solid composite polymer electrolytes based on poly (vinyl alcohol complexed with sodium salicylate were studied. The polymer electrolytes at different weight percent ratios were prepared by solution casting technique. The changes in the structures of the electrolytes were characterized by XRD, which revealed the amorphous domains of the polymer which increased with increase of sodium salicylate concentration. The complexion of the polymer electrolytes were confirmed by FTIR studies. Thermal gravimetric analysis (TGA was used to study the thermal stability of the polymer below 523 K. The decomposition decreases with increasing sodium salicylate concentration. The conductivity and dielectric properties were measured using an impedance analyzer in frequency range of 20 Hz to 1 MHz and narrow temperature range of 303 to 343 K. The conductivity increased with increase of sodium salicylate concentration and temperature. The dielectric constant and dielectric loss increased with the increase in temperature and decreased with the increase in sodium salicylate concentration.

  18. Amperometric detector for gas chromatography based on a silica sol-gel solid electrolyte.

    Science.gov (United States)

    Steinecker, William H; Miecznikowski, Krzysztof; Kulesza, Pawel J; Sandlin, Zechariah D; Cox, James A

    2017-11-01

    An electrochemical cell comprising a silica sol-gel solid electrolyte, a working electrode that protrudes into a gas phase, and reference and counter electrodes that contact the solid electrolyte comprises an amperometric detector for gas chromatography. Under potentiostatic conditions, a current related to the concentration of an analyte in the gas phase is produced by its oxidation at the three-phase boundary among the sol-gel, working electrode, and the gas phase. The sol-gel is processed to contain an electrolyte that also serves as a humidistat to maintain a constant water activity even in the presence the gas chromatographic mobile phase. Response was demonstrated toward a diverse set of analytes, namely hydrogen, 1,2-ethandithiol, phenol, p-cresol, and thioanisole. Using flow injection amperometry of hydrogen with He as the carrier gas, 90% of the steady-state current was achieved in < 1s at a flow rate of 20mLmin(-1). A separation of 1,2-ethandithiol, phenol, p-cresol, and thioanisole at a 2.2mLmin(-1) flow rate was achieved with respective detection limits (k = 3 criterion) of 4, 1, 3, and 70 ppmv when the working electrode potential was 800mV. Copyright © 2017 Elsevier B.V. All rights reserved.

  19. Aqueous liquid feed organic fuel cell using solid polymer electrolyte membrane

    Science.gov (United States)

    Surampudi, Subbarao (Inventor); Narayanan, Sekharipuram R. (Inventor); Vamos, Eugene (Inventor); Frank, Harvey A. (Inventor); Halpert, Gerald (Inventor); Olah, George A. (Inventor); Prakash, G. K. Surya (Inventor)

    1997-01-01

    A liquid organic fuel cell is provided which employs a solid electrolyte membrane. An organic fuel, such as a methanol/water mixture, is circulated past an anode of a cell while oxygen or air is circulated past a cathode of the cell. The cell solid electrolyte membrane is preferably fabricated from Nafion.TM.. Additionally, a method for improving the performance of carbon electrode structures for use in organic fuel cells is provided wherein a high surface-area carbon particle/Teflon.TM.-binder structure is immersed within a Nafion.TM./methanol bath to impregnate the electrode with Nafion.TM.. A method for fabricating an anode for use in a organic fuel cell is described wherein metal alloys are deposited onto the electrode in an electro-deposition solution containing perfluorooctanesulfonic acid. A fuel additive containing perfluorooctanesulfonic acid for use with fuel cells employing a sulfuric acid electrolyte is also disclosed. New organic fuels, namely, trimethoxymethane, dimethoxymethane, and trioxane are also described for use with either conventional or improved fuel cells.

  20. Room-Temperature Performance of Poly(Ethylene Ether Carbonate)-Based Solid Polymer Electrolytes for All-Solid-State Lithium Batteries.

    Science.gov (United States)

    Jung, Yun-Chae; Park, Myung-Soo; Kim, Duck-Hyun; Ue, Makoto; Eftekhari, Ali; Kim, Dong-Won

    2017-12-13

    Amorphous poly(ethylene ether carbonate) (PEEC), which is a copolymer of ethylene oxide and ethylene carbonate, was synthesized by ring-opening polymerization of ethylene carbonate. This route overcame the common issue of low conductivity of poly(ethylene oxide)(PEO)-based solid polymer electrolytes at low temperatures, and thus the solid polymer electrolyte could be successfully employed at the room temperature. Introducing the ethylene carbonate units into PEEC improved the ionic conductivity, electrochemical stability and lithium transference number compared with PEO. A cross-linked solid polymer electrolyte was synthesized by photo cross-linking reaction using PEEC and tetraethyleneglycol diacrylate as a cross-linking agent, in the form of a flexible thin film. The solid-state Li/LiNi0.6Co0.2Mn0.2O2 cell assembled with solid polymer electrolyte based on cross-linked PEEC delivered a high initial discharge capacity of 141.4 mAh g-1 and exhibited good capacity retention at room temperature. These results demonstrate the feasibility of using this solid polymer electrolyte in all-solid-state lithium batteries that can operate at ambient temperatures.

  1. Solid lithium electrolyte via addition of lithium salts to metal-organic frameworks

    Science.gov (United States)

    Wiers, Brian M.; Balsara, Nitash P.; Long, Jeffrey R.

    2016-12-20

    Various embodiments of the invention disclose that the uptake of LiO.sup.iPr in Mg.sub.2(dobdc) (dobdc.sup.4-=1,4-dioxido-2,5-benzenedicarboxylate) followed by soaking in a typical electrolyte solution leads to a new solid lithium electrolyte Mg.sub.2(dobdc).0.35LiO.sup.iPr.0.25LiBF.sub.4.EC.DEC. Two-point ac impedance data show a pressed pellet of this material to have a conductivity of 3.1.times.10.sup.-4 S/cm at 300 K. In addition, the results from variable-temperature measurements reveal an activation energy of approximately 0.15 eV, while single-particle data suggest that intraparticle transport dominates conduction.

  2. Electrode assembly for use in a solid polymer electrolyte fuel cell

    Science.gov (United States)

    Raistrick, Ian D.

    1989-01-01

    A gas reaction fuel cell may be provided with a solid polymer electrolyte membrane. Porous gas diffusion electrodes are formed of carbon particles supporting a catalyst which is effective to enhance the gas reactions. The carbon particles define interstitial spaces exposing the catalyst on a large surface area of the carbon particles. A proton conducting material, such as a perfluorocarbon copolymer or ruthenium dioxide contacts the surface areas of the carbon particles adjacent the interstitial spaces. The proton conducting material enables protons produced by the gas reactions adjacent the supported catalyst to have a conductive path with the electrolyte membrane. The carbon particles provide a conductive path for electrons. A suitable electrode may be formed by dispersing a solution containing a proton conducting material over the surface of the electrode in a manner effective to coat carbon surfaces adjacent the interstitial spaces without impeding gas flow into the interstitial spaces.

  3. All-solid-state lithium organic battery with composite polymer electrolyte and pillar[5]quinone cathode.

    Science.gov (United States)

    Zhu, Zhiqiang; Hong, Meiling; Guo, Dongsheng; Shi, Jifu; Tao, Zhanliang; Chen, Jun

    2014-11-26

    The cathode capacity of common lithium ion batteries (LIBs) using inorganic electrodes and liquid electrolytes must be further improved. Alternatively, all-solid-state lithium batteries comprising the electrode of organic compounds can offer much higher capacity. Herein, we successfully fabricated an all-solid-state lithium battery based on organic pillar[5]quinone (C35H20O10) cathode and composite polymer electrolyte (CPE). The poly(methacrylate) (PMA)/poly(ethylene glycol) (PEG)-LiClO4-3 wt % SiO2 CPE has an optimum ionic conductivity of 0.26 mS cm(-1) at room temperature. Furthermore, pillar[5]quinine cathode in all-solid-state battery rendered an average operation voltage of ∼2.6 V and a high initial capacity of 418 mAh g(-1) with a stable cyclability (94.7% capacity retention after 50 cycles at 0.2C rate) through the reversible redox reactions of enolate/quinonid carbonyl groups, showing favorable prospect for the device application with high capacity.

  4. Influence of strain on local structure and lithium ionic conduction in garnet-type solid electrolyte

    Science.gov (United States)

    Yamada, Hirotoshi; Ito, Tomoko; Hongahally Basappa, Rajendra; Bekarevich, Raman; Mitsuishi, Kazutaka

    2017-11-01

    All-solid-state batteries (ASSBs) have various problems associated with their usage that are normally not encountered in conventional lithium-ion batteries. Stress on interfaces between solid electrolytes and active materials is one of the key issues because the active materials change their volume during charging/discharging. In this work, first, we reveal that garnet-type solid electrolytes, Li6.5La3Zr1.5Ta0.5O12 (LLZT), prepared by the spark plasma sintering (SPS) technique, exhibit a residual tensile stress of more than 100 MPa in the direction of the SPS pressure. Then, the influence of the strain on ionic conduction is investigated in detail. It is demonstrated that the strain causes no change in the bulk resistance, while the grain boundary resistance increases in both the pre-exponential factor and the activation energy. The results suggest the importance of the strength of grain boundaries (including interfaces) for the practical application of ASSBs.

  5. All-Solid-State Lithium-Sulfur Battery based on a nanoconfined LiBH 4 Electrolyte

    NARCIS (Netherlands)

    Das, Supti; Ngene, Peter; Norby, Poul; Vegge, Tejs; de Jongh, P.E.; Blanchard, Didier

    2016-01-01

    In this work we characterize all-solid-state lithium-sulfur batteries based on nano-confined LiBH4in mesoporous silica as solid electrolytes. The nano-confined LiBH4has fast ionic lithium conductivity at room temperature, 0.1 mScm-1, negligible electronic conductivity and its cationic transport

  6. Modeling of vapor-liquid-solid equilibrium in gas - aqueous electrolyte systems

    DEFF Research Database (Denmark)

    Thomsen, Kaj; Rasmussen, Peter

    1999-01-01

    A thermodynamic model for the description of vapor-liquid-solid equilibria is introduced. This model is a combination of the extended UNIQUAC model for electrolytes and the Soave-Redlich-Kwong cubic equation of state. The model has been applied to aqueous systems containing ammonia and/or carbon...... dioxide along with various salts. Model parameters valid in the temperature range 0-110 degrees C, the pressure range from 0-100 bar, and the concentration range up to approximately 80 molal ammonia are given. The model parameters were evaluated on the basis of more than 7000 experimental data points. (C...

  7. Yttria-doped zirconia as solid electrolyte for fuel-cell applications

    Energy Technology Data Exchange (ETDEWEB)

    Butz, Benjamin

    2009-11-27

    7.3-10 mol% yttria-doped zirconia (YDZ) was studied with emphasis on its long-term stability as solid electrolyte. The decomposition of common 8.5YDZ (950 C) was detected by analytical TEM. As second issue, the microstructural and chemical properties of nanocrystalline 7.3YDZ thin films were investigated. Metastable t''-YDZ was found to precipitate in nanoscaled regions in YDZ up to 10 mol% yttria. Furthermore, a revised boundary of the c+t phase field, in which YDZ decomposes, is presented. (orig.)

  8. Correspondence between Experiment and Theory of Bulk Electrocrystallisation at Solid Electrodes in Aqueous Electrolyte

    DEFF Research Database (Denmark)

    Andersen, Jens Enevold Thaulov

    A theory of bulk-metal electrocrystallisation at solid-metal surfaces in aqueous electrolytes is presented. The electrochemical processes in the vicinity of the electrode surface are dynamic interactions between charged and uncharged species. Redox processes in the classical sense constitute only...... position relative to the electrode, the rate of reduction and oxidation may increase thus leading to current densities that exceed the magnitude of conventional diffusion current densities observed in cyclic voltammetry. This result was accomplished by including in the description a depletion layer devoid...

  9. An all-solid-state electrochemical double-layer capacitor based on a plastic crystal electrolyte

    Directory of Open Access Journals (Sweden)

    Ali eaabouimrane

    2015-08-01

    Full Text Available A plastic crystal, solid electrolyte was prepared by mixing tetrabutylammonium hexafluorophosphate salt, (C4H94NPF6, (10 molar % with succinonitrile, SCN, (N C−CH2−CH2−C N, [SCN-10%TBA-PF6]. The resultant waxy material shows a plastic crystalline phase that extend from -36 °C up to its melting at 23 °C. It shows a high ionic conductivity reaching 4 × 10−5 S/cm in the plastic crystal phase (15 °C and ~ 3 × 10−3 S/cm in the molten state (25 °C. These properties along with the high electrochemical stability rendered the use of this material as an electrolyte in an electrochemical double-layer capacitor (EDLC. The EDLC was assembled and its performance was tested by cyclic voltammetry, AC impedance spectroscopy and galvanostatic charge-discharge methods. Specific capacitance values in the range of 4-7 F/g. (of electrode active material were obtained in the plastic crystal phase at 15 °C, that although compare well with those reported for some polymer electrolytes, can be still enhanced with further development of the device and its components, and only demonstrate their great potential use for capacitors as a new application.

  10. Screen-printed SnO2/CNT quasi-solid-state gel-electrolyte supercapacitor

    Science.gov (United States)

    Kuok, Fei-Hong; Liao, Chen-Yu; Chen, Chieh-Wen; Hao, Yu-Chuan; Yu, Ing-Song; Chen, Jian-Zhang

    2017-11-01

    This study investigates a quasi-solid-state gel-electrolyte supercapacitor fabricated with nanoporous SnO2/CNT nanocomposite electrodes and a polyvinyl alcohol/sulfuric acid (PVA/H2SO4) gel electrolyte. First, pastes containing SnO2 nanoparticles, CNTs, ethyl cellulose, and terpineol are screen-printed onto carbon cloth. A tube furnace is then used for calcining the SnO2/CNT electrodes on carbon cloth. After furnace-calcination, the wettability of SnO2/CNT significantly improved; furthermore, the XPS analysis shows that number of C–O bond and oxygen content significantly decrease after furnace-calcination owing to the burnout of the ethyl cellulose by the furnace calcination processes. The furnace-calcined SnO2/CNT electrodes sandwich the PVA/H2SO4 gel electrolyte to form a supercapacitor. The fabricated supercapacitor exhibits an areal capacitance of 5.61 mF cm‑2 when flat and 5.68 mF cm‑2 under bending with a bending radius (R) of 1.0 cm. After a 1000 cycle stability test, the capacitance retention rates of the supercapacitor are 96% and 97% when flat and under bending (R  =  1.0 cm), respectively.

  11. Block Copolymer Electrolytes: Thermodynamics, Ion Transport, and Use in Solid- State Lithium/Sulfur Cells

    Science.gov (United States)

    Teran, Alexander Andrew

    Nanostructured block copolymer electrolytes containing an ion-conducting block and a modulus-strengthening block are of interest for applications in solid-state lithium metal batteries. These materials can self-assemble into well-defined microstructures, creating conducting channels that facilitate ion transport. The overall objective of this dissertation is to gain a better understanding of the behavior of salt-containing block copolymers, and evaluate their potential for use in solid-state lithium/sulfur batteries. Anionically synthesized polystyrene-b-poly(ethylene oxide) (SEO) copolymers doped with lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) salt were used as a model system. This thesis investigates the model system on several levels: from fundamental thermodynamic studies to bulk characterization and finally device assembly and testing. First, the thermodynamics of neat and salt-containing block copolymers was studied. The addition of salt to these materials is necessary to make them conductive, however even small amounts of salt can have significant effects on their phase behavior, and consequently their iontransport and mechanical properties. As a result, the effect of salt addition on block copolymer thermodynamics has been the subject of significant interest over the last decade. A comprehensive study of the thermodynamics of block copolymer/salt mixtures over a wide range of molecular weights, compositions, salt concentrations and temperatures was conducted. Next, the effect of molecular weight on ion transport in both homopolymer and copolymer electrolytes were studied over a wide range of chain lengths. Homopolymer electrolytes show an inverse relationship between conductivity and chain length, with a plateau in the infinite molecular weight limit. This is due to the presence of two mechanisms of ion conduction in homopolymers; the first mechanism is a result of the segmental motion of the chains surrounding the salt ions, 2 creating a liquid

  12. Taichi-inspired rigid-flexible coupling cellulose-supported solid polymer electrolyte for high-performance lithium batteries.

    Science.gov (United States)

    Zhang, Jianjun; Yue, Liping; Hu, Pu; Liu, Zhihong; Qin, Bingsheng; Zhang, Bo; Wang, Qingfu; Ding, Guoliang; Zhang, Chuanjian; Zhou, Xinhong; Yao, Jianhua; Cui, Guanglei; Chen, Liquan

    2014-09-03

    Inspired by Taichi, we proposed rigid-flexible coupling concept and herein developed a highly promising solid polymer electrolyte comprised of poly (ethylene oxide), poly (cyano acrylate), lithium bis(oxalate)borate and robust cellulose nonwoven. Our investigation revealed that this new class solid polymer electrolyte possessed comprehensive properties in high mechanical integrity strength, sufficient ionic conductivity (3 × 10(-4) S cm(-1)) at 60°C and improved dimensional thermostability (up to 160°C). In addition, the lithium iron phosphate (LiFePO4)/lithium (Li) cell using such solid polymer electrolyte displayed superior rate capacity (up to 6 C) and stable cycle performance at 80°C. Furthermore, the LiFePO4/Li battery could also operate very well even at an elevated temperature of 160°C, thus improving enhanced safety performance of lithium batteries. The use of this solid polymer electrolyte mitigates the safety risk and widens the operation temperature range of lithium batteries. Thus, this fascinating study demonstrates a proof of concept of the use of rigid-flexible coupling solid polymer electrolyte toward practical lithium battery applications with improved reliability and safety.

  13. Improvement of cathode-electrolyte interfaces of tubular solid oxide fuel cells by fabricating dense YSZ electrolyte membranes with indented surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Dong, Dehua; Liu, Mingfei; Xie, Kui; Sheng, Jin; Liu, Xingqin; Meng, Guangyao [Department of Materials Science and Engineering, University of Science and Technology of China, Hefei 230026 (China); Wang, Yonghong; Peng, Xiaobo [Institute of Materials Science and Engineering, Hefei University of Technology (China)

    2008-01-03

    To improve cathode-electrolyte interfaces of solid oxide fuel cells (SOFCs), dense YSZ electrolyte membranes with indented surfaces were fabricated on tubular NiO/YSZ anode supports by two comparable methods. Electrochemistry impedance spectroscopy (EIS) and current-voltage tests of the cells were carried out to characterize the cathode-electrolyte interfaces. Results showed that the electrode polarization resistances of the modified cells were reduced by 52% and 35% at 700 C, and the maximum power densities of cells were remarkably increased, even by 146.6% and 117.8% at lower temperature (700 C), respectively. The indented surfaces extended the active zone of cathode and enhanced interfacial adhesion, which led to the major improvement in the cell performance. (author)

  14. Nitrogen dissociation during RF sputtering of Lipon electrolyte for all-solid-states batteries

    DEFF Research Database (Denmark)

    Stamate, Eugen; Christiansen, Ane Sælland; Holtappels, Peter

    2013-01-01

    films in nitrogen gas is investigated by mass appearance spectrometry, optical emission spectroscopy and electrostatic probes and the results are correlated with electrochemical properties of the films. Low pressure and moderate power are found to be most beneficial for the growth of good quality films......Small size and high power density secondary batteries are desired for a large number of applications based on miniature wireless devices and sensors that need to be compatible with the microelectronic fabrication technology. This fact resulted in the development of solid electrolytes, like lithium...... phosphorus oxynitride (Lipon), that can be compacted with the anode and cathode electrodes in an all-solid-states structure where the nitrogen incorporation is considered one of the key parameters for controlling the ionic conductivity. In this work the nitrogen dissociation during RF sputtering of Lipon...

  15. A modified anode/electrolyte structure for a solid oxide electrochemical cell and a method for making said structure

    DEFF Research Database (Denmark)

    2013-01-01

    A novel modified anode/electrolyte structure for a solid oxide electrochemical cell is an assembly comprising (a) an anode consisting of a backbone of electronically conductive perovskite oxides selected from the group of doped strontium titanates and mixtures thereof, (b) a scandia and yttria...... treatments resulted in a distribution of the metallic and/or ceramic interlayers in the electrolyte/anode backbone junction taking place. The structure is prepared by (a) depositing a ceramic interlayer onto one side of the electrolyte, (b) optionally applying a metallic interlayer thereon, (c) repeating...

  16. Fe-doped 8YSZ at different composition for solid electrolyte in solid oxide fuel cell

    Directory of Open Access Journals (Sweden)

    Johar B.

    2016-01-01

    Full Text Available Pure 8 mol% yttria stabilized zirconia (YSZ and Fe-doped (1 mol%, 2 mol% and 3 mol% YSZ electrolyte were prepared and sintered at 1550°C. Transition metal oxide is added into YSZ as sintering aided has a function to reduce the sintering temperature. The microstructure, crystal structure and ionic conductivity of pure YSZ and Fe-doped YSZ at different composition were investigated. The amount of cubic phase decreased as the amount of Fe increased. Fe-doped 8YSZ had higher conductivity than pure 8YSZ. The ionic conductivity of 3FeYSZ is 9.35×10−8 S/cm higher than 1FeYSZ which is 4.72×10−9 S/cm when operated at 300°C.

  17. The NASA "PERS" Program: Solid Polymer Electrolyte Development for Advanced Lithium-Based Batteries

    Science.gov (United States)

    Baldwin, Richard S.; Bennett, William R.

    2007-01-01

    In fiscal year 2000, The National Aeronautics and Space Administration (NASA) and the Air Force Research Laboratory (AFRL) established a collaborative effort to support the development of polymer-based, lithium-based cell chemistries and battery technologies to address the next generation of aerospace applications and mission needs. The ultimate objective of this development program, which was referred to as the Polymer Energy Rechargeable System (PERS), was to establish a world-class technology capability and U.S. leadership in polymer-based battery technology for aerospace applications. Programmatically, the PERS initiative exploited both interagency collaborations to address common technology and engineering issues and the active participation of academia and private industry. The initial program phases focused on R&D activities to address the critical technical issues and challenges at the cell level. Out of a total of 38 proposals received in response to a NASA Research Announcement (NRA) solicitation, 18 proposals (13 contracts and 5 grants) were selected for initial award to address these technical challenges. Brief summaries of technical approaches, results and accomplishments of the PERS Program development efforts are presented. With Agency support provided through FY 2004, the PERS Program efforts were concluded in 2005, as internal reorganizations and funding cuts resulted in shifting programmatic priorities within NASA. Technically, the PERS Program participants explored, to various degrees over the lifetime of the formal program, a variety of conceptual approaches for developing and demonstrating performance of a viable advanced solid polymer electrolyte possessing the desired attributes, as well as several participants addressing all components of an integrated cell configuration. Programmatically, the NASA PERS Program was very successful, even though the very challenging technical goals for achieving a viable solid polymer electrolyte material or

  18. Electrospinning of Ceramic Solid Electrolyte Nanowires for Lithium-Ion Batteries with Enhanced Ionic Conductivity

    Science.gov (United States)

    Yang, Ting

    Solid electrolytes have great potential to address the safety issues of Li-ion batteries, but better synthesis methods are still required for ceramics electrolytes such as lithium lanthanum titanate (LLTO) and lithium lanthanum zirconate (LLZO). Pellets made from ceramic nanopowders using conventional sintering can be porous due to the agglomeration of nanoparticles (NPs). Electrospinning is a simple and versatile technique for preparing oxide ceramic nanowires (NWs) and was used to prepare electrospun LLTO and LLZO NWs. Pellets prepared from the electrospun LLTO NWs had higher density, less void space, and higher Li+ conductivity compared to those comprised of LLTO prepared with conventional sol-gel methods, which demonstrated the potential that electrospinning can provide towards improving the properties of sol-gel derived ceramics. Cubic phase LLZO was stabilized at room temperature in the form of electrospun NWs without extrinsic dopants. Bulk LLZO with tetragonal structure was transformed to the cubic phase using particle size reduction via ball milling. Heating conditions that promoted particle coalescence and grain growth induced a transformation from the cubic to tetragonal phase in both types of nanostructured LLZO. Composite polymer solid electrolyte was fabricated using LLZO NWs as the filler and showed an improved ionic conductivity at room temperature. Nuclear magnetic resonance studies show that LLZO NWs partially modify the polymer matrix and create preferential pathways for Li+ conduction through the modified polymer regions. Doping did not have significant effect on improving the overall conductivity as the interfaces played a predominant role. By comparing fillers with different morphologies and intrinsic conductivities, it was found that both NW morphology and high intrinsic conductivity are desired.

  19. Reshaping Lithium Plating/Stripping Behavior via Bifunctional Polymer Electrolyte for Room-Temperature Solid Li Metal Batteries.

    Science.gov (United States)

    Zeng, Xian-Xiang; Yin, Ya-Xia; Li, Nian-Wu; Du, Wen-Cheng; Guo, Yu-Guo; Wan, Li-Jun

    2016-12-14

    High-energy rechargeable Li metal batteries are hindered by dendrite growth due to the use of a liquid electrolyte. Solid polymer electrolytes, as promising candidates to solve the above issue, are expected to own high Li ion conductivity without sacrificing mechanical strength, which is still a big challenge to realize. In this study, a bifunctional solid polymer electrolyte exactly having these two merits is proposed with an interpenetrating network of poly(ether-acrylate) (ipn-PEA) and realized via photopolymerization of ion-conductive poly(ethylene oxide) and branched acrylate. The ipn-PEA electrolyte with facile processing capability integrates high mechanical strength (ca. 12 GPa) with high room-temperature ionic conductance (0.22 mS cm-1), and significantly promotes uniform Li plating/stripping. Li metal full cells assembled with ipn-PEA electrolyte and cathodes within 4.5 V vs Li+/Li operate effectively at a rate of 5 C and cycle stably at a rate of 1 C at room temperature. Because of its fabrication simplicity and compelling characteristics, the bifunctional ipn-PEA electrolyte reshapes the feasibility of room-temperature solid-state Li metal batteries.

  20. Fuel electrode for solid oxide electrolyte fuel cell. Kotai denkaishitsugata nenryo denchi no nenryo denkyoku

    Energy Technology Data Exchange (ETDEWEB)

    Sawada, A.

    1993-03-19

    Cermet mixed with nickel and stabilized zirconia (YSZ) is normally used for the fuel electrode of the high temperature solid oxide electrolyte fuel cell which uses coal gasification gas or natural gas as the primary fuel. When acidic YSZ is used as the aggregate for this electrode, however, carbon tends to precipitate to shorten the life of the fuel cell. This invention relates to means of preventing direct contact of hydrocarbon with the first porous electrode layer, wherein the first porous electrode layer containing YSZ aggregate and nickel metal or its oxide particles is formed on the surface of the solid electrolyte substrate, on which the second porous electrode layer containing basic aggregate and nickel metal or its oxide particles is formed. MgAl2O4, CaAl2O4, MgO[center dot]2TiO2, and MgO[center dot]ZrO2 are used as the basic aggregates which comprise the second porous electrode layer. 12 figs., 2 tabs.

  1. Development of layered anode structures supported over Apatite-type Solid Electrolytes

    Directory of Open Access Journals (Sweden)

    Pandis P.

    2016-01-01

    Full Text Available Apatite-type lanthanum silicates (ATLS materials have attracted interest in recent literature as solid electrolytes for SOFCs. The fabrication of an ATLS based fuel cell with the state-of-art electrodes (NiO/YSZ as anode and LSCF or LSM as cathode can show degradation after long operation hours due to Si diffusion mainly towards the anode. In this work, we report a “layer-by-layer anodic electrodes” fabrication by means of spin coating and physical spraying. The overall aim of this work is the successful fabrication of such a layered structure including suitable blocking layers towards the inhibition of Si interdiffusion from the apatite electrolyte to the anode. The results showed that the deposition of 3 layers of LFSO/GDC (3μm, NiO/GDC (4μm and the final NiO/YSZ anode layer provided a stable half-cell, with no solid state reaction occurring among the electrodes and no Si diffusion observed towards the anode after thermal treatment at 800°C for 120h.

  2. Solid state NMR investigation of a novel Li ion ceramic electrolyte. Li doped BPO sub 4

    CERN Document Server

    Dodd, A J

    2002-01-01

    Over the last decade lithium ion conducting batteries have emerged as the leading technology in battery materials. Their performance, however, is limited to applications below around 50 deg C by the liquid nature of the electrolytes used. In the quest for a solid state electrolyte for use in high temperature applications the nano-crystalline ceramic lithium doped boron phosphate material was developed. Solid state nuclear magnetic resonance (NMR) has been employed to investigate some of the fundamental properties of this material including ionic mobility, defect structure, sample purity and ionic distribution. The findings of this work show that when synthesised at a reaction temperature above 600 deg C the loss of boron from the structure results in the incorporation of vacancy sites about which the Li ions gather in small clusters. Multiple-pulse multiple-quantum spin counting techniques are employed in an effort to count the number of quadrupolar sup 7 Li nuclei interacting in a cluster though it is ultima...

  3. Improved thermal stability of lithium ion battery by using cresyl diphenyl phosphate as an electrolyte additive

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Qingsong; Ping, Ping; Sun, Jinhua [State Key Laboratory of Fire Science, University of Science and Technology of China, No. 96 Jinzhai Road, Hefei 230026, Anhui (China); Chen, Chunhua [Department of Materials Science and Engineering, University of Science and Technology of China, No. 96 Jinzhai Road, Hefei 230026, Anhui (China)

    2010-11-01

    To enhance the safety of lithium ion battery, cresyl diphenyl phosphate (CDP) is explored as an additive in 1.0 M LiPF{sub 6}/ethylene carbonate (EC) + diethyl carbonate (DEC) (1:1 wt.). The electrochemical performances of LiCoO{sub 2}/CDP-electrolyte/C cells are tested. At the thermal aspect, the thermal stability of the electrolyte with CDP is detected firstly by using a C80 micro-calorimeter, and then the charged LiCoO{sub 2}/CDP-electrolyte/C cells are disassembled and wrapped to detect the thermal behaviors. The results indicate that CDP-containing electrolyte enhances the thermal stabilities of electrolyte and lithium ion battery, and the electrochemical performances of LiCoO{sub 2}/CDP-electrolyte/C cell become slightly worse by using CDP in the electrolyte. Furthermore, the cell with 10% (wt.) CDP-containing electrolyte shows better cycle efficiency than that of other CDP-containing electrolyte, such as containing 5% (wt.) CDP and 15% (wt.) CDP. This maybe because that the mass ratio between CDP and electrolyte is close to the reaction stoichiometric ratio in the 10% (wt.) CDP-containing electrolyte, where stable solid electrolyte interphase (SEI) is formed. Therefore, 10% CDP-containing electrolyte improves the safety of lithium ion battery and keeps its electrochemical performance. (author)

  4. Silica nanoparticle doped organic ionic plastic crystal electrolytes for highly efficient solid-state dye-sensitized solar cells.

    Science.gov (United States)

    Shi, Chengzhen; Qiu, Lihua; Chen, Xiaojian; Zhang, Haigang; Wang, Lei; Yan, Feng

    2013-02-01

    Organic ionic plastic crystal, 1-propyl-1-methylpyrrolidinium iodide (P₁₃I), which possesses a broad plastic phase from -36 to 135 °C, was doped with silica nanoparticles (SiO₂ NPs) and 1-ethyl-3-methylimidazolium iodide (EMII), for the preparation of SiO₂/EMII/P₁₃I solid-state electrolytes for dye-sensitized solar cells (DSSCs). The thermal properties of all the electrolytes, including solid-solid phase transitions and melting temperatures, were investigated by differential scanning calorimetry (DSC). The effect of silica particles on the ionic conductivity, diffusion of I⁻/I₃⁻ redox couple in electrolytes, and photovoltaic performance for solid-state DSSCs were investigated. The fabricated solid-state DSSCs yielded a high power conversion efficiency of 5.25% under simulated air mass 1.5 solar spectrum illuminations at 50 mW cm⁻². Furthermore, the DSSCs based on SiO₂/EMII/P₁₃I solid-state electrolytes show good stability after an accelerating aging test, demonstrating potential practical applications.

  5. Molecular motion in polymer electrolytes. An investigation of methods for improving the conductivity of solid polymer electrolytes

    CERN Document Server

    Webster, M I

    2002-01-01

    Three methods were explored with a view to enhancing the ionic conductivity of polymer electrolytes; namely the addition of an inert, inorganic filler, the addition of a plasticizer and the incorporation of the electrolyte in the pores of silica matrices. There have been a number of reports, which suggest the addition of nanocrystalline oxides to polymer electrolytes increases the ionic conductivities by about a factor of two. In this thesis studies of the polymer electrolyte NaSCN.P(EO) sub 8 with added nanocrystalline alumina powder are reported which show no evidence of enhanced conductivity. The addition of a plasticizer to polymer electrolytes will increase the ionic conductivity. A detailed study was made of the polymer electrolytes LiT.P(EO) sub 1 sub 0 and LiClO sub 4.P(EO) sub 1 sub 0 with added ethylene carbonate plasticizer. The conductivities showed an enhancement, however this disappeared on heating under vacuum. The present work suggests that the plasticised system is not thermodynamically stabl...

  6. All-solid-state lithium-sulfur battery based on a nanoconfined LiBH4 electrolyte

    DEFF Research Database (Denmark)

    Das, Supti; Ngene, Peter; Norby, Poul

    2016-01-01

    In this work we characterize all-solid-state lithium-sulfur batteries based on nano-confined LiBH4 in mesoporous silica as solid electrolytes. The nano-confined LiBH4 has fast ionic lithium conductivity at room temperature, 0.1 mScm-1, negligible electronic conductivity and its cationic transport...... number (t+ = 0.96), close to unity, demonstrates a purely cationic conductor. The electrolyte has an excellent stability against lithium metal. The behavior of the batteries is studied by cyclic voltammetry and repeated charge/discharge cycles in galvanostatic conditions. The batteries show very good...

  7. Fluorine-free electrolytes for all-solid sodium-ion batteries based on percyano-substituted organic salts

    OpenAIRE

    Anna Bitner-Michalska; Gene M. Nolis; Grażyna Żukowska; Aldona Zalewska; Marcin Poterała; Tomasz Trzeciak; Maciej Dranka; Michał Kalita; Piotr Jankowski; Leszek Niedzicki; Janusz Zachara; Marek Marcinek; Władysław Wieczorek

    2017-01-01

    A new family of fluorine-free solid-polymer electrolytes, for use in sodium-ion battery applications, is presented. Three novel sodium salts withdiffuse negative charges: sodium pentacyanopropenide (NaPCPI), sodium 2,3,4,5-tetracyanopirolate (NaTCP) and sodium 2,4,5-tricyanoimidazolate (NaTIM) were designed andtested in a poly(ethylene oxide) (PEO) matrix as polymer electrolytes for anall-solid sodium-ion battery. Due to unique, non-covalent structural configurations of anions, improved ionic...

  8. Study of metal--oxygen solid solutions utilizing solid electrolytic cells

    Energy Technology Data Exchange (ETDEWEB)

    Lauf, Robert John [Univ. of Illinois, Urbana-Champaign, IL (United States)

    1978-10-01

    A study was made of the thermodynamic and kinetic behavior of oxygen in a number of Group V metals and alloys. Investigations were made with a ThO2Y2O3 electrolyte over the temperature range of 600 to 1150°to 1423°K). The activity of oxygen in three Nb--Ta alloys (nominally 25, 50, and 75 at. % Ta) was found to obey Henry's Law up to the solubility limit in each alloy. The standard entropy and enthalpy of solution of oxygen in the three Nb--Ta alloys were intermediate between those for pure niobium and pure tantalum, and varied almost linearly with Nb : Ta content. The diffusion coefficient of oxygen was measured in niobium and vanadium, and the values were found to be in excellent agreement with literature values obtained by a variety of techniques. The diffusion coefficient of oxygen in each of several dilute substitutional niobium alloys was measured and compared to the diffusion coefficient in pure niobium. The addition of 1 to 5% substitutional solutes resulted in as much as an order-of-magnitude decrease in the oxygen diffusivity. This decrease is believed to be due to trapping of oxygen by substitutional solute atoms. The substitutional-oxygen binding or ''trap'' energies (in eV) for several substitutional solutes in niobium were determined to be: Ta: 0.3 ± 0.1; V: 0.55 ± 0.05; Ti: 0.7 ± 0.1; Zr: 0.7 ± 0.05. The trap energy is rationalized as being the sum of a chemical interaction and an elastic interaction. 27 figures, 9 tables.

  9. Investigation of the Reversible Lithiation of an Oxide Free Aluminum Anode by a LiBH4 Solid State Electrolyte

    Directory of Open Access Journals (Sweden)

    Jason A. Weeks

    2017-11-01

    Full Text Available In this study, we analyze and compare the physical and electrochemical properties of an all solid-state cell utilizing LiBH4 as the electrolyte and aluminum as the active anode material. The system was characterized by galvanostatic lithiation/delithiation, cyclic voltammetry (CV, X-ray diffraction (XRD, energy dispersive X-ray spectroscopy (EDS, Raman spectroscopy, electrochemical impedance spectroscopy (EIS, and scanning electron microscopy (SEM. Constant current cycling demonstrated that the aluminum anode can be reversibly lithiated over multiple cycles utilizing a solid-state electrolyte. An initial capacity of 895 mAh/g was observed and is close to the theoretical capacity of aluminum. Cyclic voltammetry of the cell was consistent with the constant current cycling data and showed that the reversible lithiation/delithiation of aluminum occurs at 0.32 V and 0.38 V (vs. Li+/Li respectively. XRD of the aluminum anode in the initial and lithiated state clearly showed the formation of a LiAl (1:1 alloy. SEM-EDS was utilized to examine the morphological changes that occur within the electrode during cycling. This work is the first example of reversible lithiation of aluminum in a solid-state cell and further emphasizes the robust nature of the LiBH4 electrolyte. This demonstrates the possibility of utilizing other high capacity anode materials with a LiBH4 based solid electrolyte in all-solid-state batteries.

  10. Graphene-Analogues Boron Nitride Nanosheets Confining Ionic Liquids: A High-Performance Quasi-Liquid Solid Electrolyte.

    Science.gov (United States)

    Li, Mingtao; Zhu, Wenshuai; Zhang, Pengfei; Chao, Yanhong; He, Qian; Yang, Bolun; Li, Huaming; Borisevich, Albinab; Dai, Sheng

    2016-07-01

    Solid electrolytes are one of the most promising electrolyte systems for safe lithium batteries, but the low ionic conductivity of these electrolytes seriously hinders the development of efficient lithium batteries. Here, a novel class of graphene-analogues boron nitride (g-BN) nanosheets confining an ultrahigh concentration of ionic liquids (ILs) in an interlayer and out-of-layer chamber to give rise to a quasi-liquid solid electrolyte (QLSE) is reported. The electron-insulated g-BN nanosheet host with a large specific surface area can confine ILs as much as 10 times of the host's weight to afford high ionic conductivity (3.85 × 10(-3) S cm(-1) at 25 °C, even 2.32 × 10(-4) S cm(-1) at -20 °C), which is close to that of the corresponding bulk IL electrolytes. The high ionic conductivity of QLSE is attributed to the enormous absorption for ILs and the confining effect of g-BN to form the ordered lithium ion transport channels in an interlayer and out-of-layer of g-BN. Furthermore, the electrolyte displays outstanding electrochemical properties and battery performance. In principle, this work enables a wider tunability, further opening up a new field for the fabrication of the next-generation QLSE based on layered nanomaterials in energy conversion devices. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  11. A novel quasi-solid state electrolyte with highly effective polysulfide diffusion inhibition for lithium-sulfur batteries.

    Science.gov (United States)

    Zhong, Hai; Wang, Chunhua; Xu, Zhibin; Ding, Fei; Liu, Xinjiang

    2016-05-05

    Polymer solid state electrolytes are actively sought for their potential application in energy storage devices, particularly lithium metal rechargeable batteries. Herein, we report a polymer with high concentration salts as a quasi-solid state electrolyte used for lithium-sulfur cells, which shows an ionic conductivity of 1.6 mS cm(-1) at room temperature. The cycling performance of Li-S battery with this electrolyte shows a long cycle life (300 cycles) and high coulombic efficiency (>98%), without any consuming additives in the electrolyte. Moreover, it also shows a remarkably decreased self-discharge (only 0.2%) after storage for two weeks at room temperature. The reason can be attributed to that the electrolyte can suppress polysulfide anions diffusion, due to the high ratio oxygen atoms with negative charges which induce an electrical repulsion to the polysulfide anions, and their relatively long chains which can provide additional steric hindrance. Thus, the polysulfide anions can be located around carbon particles, which result in remarkably improved overall electrochemical performance, and also the electrolyte have a function of suppress the formation of lithium dendrites on the lithium anode surface.

  12. A novel quasi-solid state electrolyte with highly effective polysulfide diffusion inhibition for lithium-sulfur batteries

    Science.gov (United States)

    Zhong, Hai; Wang, Chunhua; Xu, Zhibin; Ding, Fei; Liu, Xinjiang

    2016-01-01

    Polymer solid state electrolytes are actively sought for their potential application in energy storage devices, particularly lithium metal rechargeable batteries. Herein, we report a polymer with high concentration salts as a quasi-solid state electrolyte used for lithium-sulfur cells, which shows an ionic conductivity of 1.6 mS cm−1 at room temperature. The cycling performance of Li-S battery with this electrolyte shows a long cycle life (300 cycles) and high coulombic efficiency (>98%), without any consuming additives in the electrolyte. Moreover, it also shows a remarkably decreased self-discharge (only 0.2%) after storage for two weeks at room temperature. The reason can be attributed to that the electrolyte can suppress polysulfide anions diffusion, due to the high ratio oxygen atoms with negative charges which induce an electrical repulsion to the polysulfide anions, and their relatively long chains which can provide additional steric hindrance. Thus, the polysulfide anions can be located around carbon particles, which result in remarkably improved overall electrochemical performance, and also the electrolyte have a function of suppress the formation of lithium dendrites on the lithium anode surface. PMID:27146645

  13. A Rechargeable Li-Air Fuel Cell Battery Based on Garnet Solid Electrolytes

    Science.gov (United States)

    Sun, Jiyang; Zhao, Ning; Li, Yiqiu; Guo, Xiangxin; Feng, Xuefei; Liu, Xiaosong; Liu, Zhi; Cui, Guanglei; Zheng, Hao; Gu, Lin; Li, Hong

    2017-01-01

    Non-aqueous Li-air batteries have been intensively studied in the past few years for their theoretically super-high energy density. However, they cannot operate properly in real air because they contain highly unstable and volatile electrolytes. Here, we report the fabrication of solid-state Li-air batteries using garnet (i.e., Li6.4La3Zr1.4Ta0.6O12, LLZTO) ceramic disks with high density and ionic conductivity as the electrolytes and composite cathodes consisting of garnet powder, Li salts (LiTFSI) and active carbon. These batteries run in real air based on the formation and decomposition at least partially of Li2CO3. Batteries with LiTFSI mixed with polyimide (PI:LiTFSI) as a binder show rechargeability at 200 °C with a specific capacity of 2184 mAh g-1carbon at 20 μA cm-2. Replacement of PI:LiTFSI with LiTFSI dissolved in polypropylene carbonate (PPC:LiTFSI) reduces interfacial resistance, and the resulting batteries show a greatly increased discharge capacity of approximately 20300 mAh g-1carbon and cycle 50 times while maintaining a cutoff capacity of 1000 mAh g-1carbon at 20 μA cm-2 and 80 °C. These results demonstrate that the use of LLZTO ceramic electrolytes enables operation of the Li-air battery in real air at medium temperatures, leading to a novel type of Li-air fuel cell battery for energy storage.

  14. Fabrication of thin yttria-stabilized-zirconia dense electrolyte layers by inkjet printing for high performing solid oxide fuel cells

    DEFF Research Database (Denmark)

    Esposito, Vincenzo; Gadea, Christophe; Hjelm, Johan

    2015-01-01

    In this work, we present how a low-cost HP Deskjet 1000 inkjet printer was used to fabricate a 1.2 mm thin, dense and gas tight 16 cm2 solid oxide fuel cells (SOFC) electrolyte. The electrolyte was printed using an ink made of highly diluted (...) powders (50 nm in size) in an aqueous medium. The ink was designed to be a highly dispersed, long term stable colloidal suspension, with optimal printability characteristics. The electrolyte was made by a multiple printing procedure, which ensures coverage of the several flaws occurring in a single...... printing pass. Together with an optimized sintering procedure this resulted in good adhesion and densification of the electrolyte. The SOFC exhibited a close-to-theoretical open circuit voltage and a remarkable peak power density above 1.5 W cm-2 at 800 °C....

  15. Ionic conductivity studies of solid oxide fuel cell electrolytes and theoretical modeling of an entire solid oxide fuel cell

    Science.gov (United States)

    Pornprasertsuk, Rojana

    Because of the steep increase in oil prices, the global warming effect and the drive for energy independence, alternative energy research has been encouraged worldwide. The sustainable fuels such as hydrogen, biofuel, natural gas, and solar energy have attracted the attention of researchers. To convert these fuels into a useful energy source, an energy conversion device is required. Fuel cells are one of the energy conversion devices which convert chemical potentials into electricity. Due to their high efficiency, the ease to scale from 1 W range to megawatts range, no recharging requirement and the lack of CO2 and NOx emission (if H2 and air/O 2 are used), fuel cells have become a potential candidate for both stationary power generators and portable applications. This thesis has been focused primarily on solid oxide fuel cell (SOFC) studies due to its high efficiency, varieties of fuel choices, and no water management problem. At the present, however, practical applications of SOFCs are limited by high operating temperatures that are needed to create the necessary oxide-ion vacancy mobility in the electrolyte and to create sufficient electrode reactivities. This thesis introduces several experimental and theoretical approaches to lower losses both in the electrolyte and the electrodes. Yttria stabilized zirconia (YSZ) is commonly used as a solid electrolyte for SOFCs due to its high oxygen-ion conductivity. To improve the ionic conductivity for low temperature applications, an approach that involves dilating the structure by irradiation and introducing edge dislocations into the electrolyte was studied. Secondly, to understand the activation loss in SOFC, the kinetic Monte Carlo (KMC) technique was implemented to model the SOFC operation to determining the rate-limiting step due to the electrodes on different sizes of Pt catalysts. The isotope exchange depth profiling technique was employed to investigate the irradiation effect on the ionic transport in different

  16. Polystyrene-Al2O3 composite solid polymer electrolyte for lithium secondary battery.

    Science.gov (United States)

    Lim, Yu-Jeong; An, Yu-Ha; Jo, Nam-Ju

    2012-01-05

    In a common salt-in-polymer electrolyte, a polymer which has polar groups in the molecular chain is necessary because the polar groups dissolve lithium salt and coordinate cations. Based on the above point of view, polystyrene [PS] that has nonpolar groups is not suitable for the polymer matrix. However, in this PS-based composite polymer-in-salt system, the transport of cations is not by segmental motion but by ion-hopping through a lithium percolation path made of high content lithium salt. Moreover, Al2O3 can dissolve salt, instead of polar groups of polymer matrix, by the Lewis acid-base interactions between the surface group of Al2O3 and salt. Notably, the maximum enhancement of ionic conductivity is found in acidic Al2O3 compared with neutral and basic Al2O3 arising from the increase of free ion fraction by dissociation of salt. It was revealed that PS-Al2O3 composite solid polymer electrolyte containing 70 wt.% salt and 10 wt.% acidic Al2O3 showed the highest ionic conductivity of 9.78 × 10-5 Scm-1 at room temperature.

  17. Electrical and morphological analysis of chitosan:AgTf solid electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Aziz, Shujahadeen B., E-mail: shujaadeen78@yahoo.com [School of Physics, Faculty of Science and Science Education, University of Sulaimani, Kurdistan Regional Government, Sulaimani (Iraq); Abidin, Zul Hazrin Z. [Centre for Ionics University of Malaya (CIUM), Department of Physics, Faculty of Science, University of Malaya, 50603 Kuala Lumpur (Malaysia)

    2014-04-01

    Solution cast technique is employed to prepare solid polymer electrolyte films based on chitosan (host polymer) and silver triflate (AgCF{sub 3}SO{sub 3}, doping salt) using (1%) acetic acid as a common solvent. The effect of salt concentration on both EP and bulk materials dielectric properties has been analyzed. Physically the original relationship between the bulk dielectric constant and DC conductivity has been interpreted. It is demonstrated that the dielectric constant and dielectric loss values decrease at higher temperatures due to the reduction of silver ions. Scanning electron microscopy (SEM) and energy dispersive analysis of X-ray (EDAX) indicate the presence of metallic silver particles. The ac conductivity spectra shows three distinct regions and obeys the Jonscher's power law at high frequency regions. The temperature dependence of frequency exponent (s) shows the crossover from CBH model to SP model. - Highlights: • A strong relationship exists between DC conductivity and dielectric constant. • The decrease of ε′ and ε″ is due to the reduction of silver ions (Ag{sup +} → Ag{sup o}). • The morphological results reveal the formation of silver particles. • The AC conduction models can be applicable for ion conducting polymer electrolytes.

  18. Temperature dependent dielectric properties and ion transportation in solid polymer electrolyte for lithium ion batteries

    Energy Technology Data Exchange (ETDEWEB)

    Sengwa, R. J., E-mail: rjsengwa@rediffmail.com; Dhatarwal, Priyanka, E-mail: dhatarwalpriyanka@gmail.com; Choudhary, Shobhna, E-mail: shobhnachoudhary@rediffmail.com [Dielectric Research Laboratory, Department of Physics, Jai Narain Vyas University, Jodhpur – 342 005 (India)

    2016-05-06

    Solid polymer electrolyte (SPE) film consisted of poly(ethylene oxide) (PEO) and poly(methyl methacrylate) (PMMA) blend matrix with lithium tetrafluroborate (LiBF{sub 4}) as dopant ionic salt and poly(ethylene glycol) (PEG) as plasticizer has been prepared by solution casting method followed by melt pressing. Dielectric properties and ionic conductivity of the SPE film at different temperatures have been determined by dielectric relaxation spectroscopy. It has been observed that the dc ionic conductivity of the SPE film increases with increase of temperature and also the decrease of relaxation time. The temperature dependent relaxation time and ionic conductivity values of the electrolyte are governed by the Arrhenius relation. Correlation observed between dc conductivity and relaxation time confirms that ion transportation occurs with polymer chain segmental dynamics through hopping mechanism. The room temperature ionic conductivity is found to be 4 × 10{sup −6} S cm{sup −1} which suggests the suitability of the SPE film for rechargeable lithium batteries.

  19. Enhanced solid-state electrolytes made of lithium phosphorous oxynitride films

    Energy Technology Data Exchange (ETDEWEB)

    Ribeiro, J.F., E-mail: jribeiro@dei.uminho.pt [University of Minho, Dept Industrial Electronics, Campus Azurem, 4800-058 Guimaraes (Portugal); Sousa, R.; Carmo, J.P.; Goncalves, L.M.; Silva, M.F. [University of Minho, Dept Industrial Electronics, Campus Azurem, 4800-058 Guimaraes (Portugal); Silva, M.M. [University of Minho, Chemistry Centre, Braga (Portugal); Correia, J.H. [University of Minho, Dept Industrial Electronics, Campus Azurem, 4800-058 Guimaraes (Portugal)

    2012-11-01

    This paper presents glassy films of lithium phosphorus oxynitride electrolyte with an amorphous structure and improved ionic conductivity suitable for solid-state batteries. The films of lithium phosphorus oxynitride electrolyte were obtained by deposition using the RF sputtering technique in a reactive N{sub 2} atmosphere. The measurements showed films with ionic conductivities in range of 10{sup -7}-10{sup -6} S{center_dot}cm{sup -1}, for temperatures between 22 Degree-Sign C and 43 Degree-Sign C. The depositions were done at several pressures (0.03 Pa, 0.7 Pa and 1 Pa) and for RF applied powers of 150 W and 200 W, in order to evaluate the best deposition set-point. The highest ionic conductivity of 10{sup -6} S{center_dot}cm{sup -1} was measured under a practical room temperature of 35 Degree-Sign C on the best films. These results are comparable with the related state-of-the-art. - Highlights: Black-Right-Pointing-Pointer Lithium phosphorous oxynitride films obtained by RF sputtering Black-Right-Pointing-Pointer Ionic conductivity correlated with deposition settings Black-Right-Pointing-Pointer Ionic conductivity comparable and correlated with the state-of-the-art.

  20. Hydrogen production by electrochemical decomposition of formic acid via solid polymer electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Kilic, Ebru Oender [KOSGEB Bursa Business Development Center, Besevler Kucuk Sanayi Sitesi 16149 Nilufer/Bursa (Turkey); Koparal, Ali Savas; Oeguetveren, Uelker Bakir [Anadolu University, Iki Eylul Campus, Applied Research Center for Environmental Problems 26555 Eskisehir (Turkey); Anadolu University, Iki Eylul Campus, Department of Environmental Engineering, 26555 Eskisehir (Turkey)

    2009-01-15

    The aim of this work is to investigate the feasibility of simultaneous hydrogen production by electrochemical decomposition of formic acid via solid polymer electrolyte (SPE) in an electrochemical reactor. Titanium oxide coated with iridium oxide as anode and carbon fibre with Pt catalyst as cathode were used in the experiments. Effects of applied current density, flow rates and temperature of formic acid solution, concentration of supporting electrolyte and pH of the solution on performance of the process have been investigated. The effect of membrane thickness has also been examined. The results suggest that electrolysis using SPE is a promising method for the treatment of organic pollutants. Hydrogen with purity of 99.999% at ambient temperature by using carbon fibre cathode with Pt catalyst can be produced simultaneously and COD removal efficiency of 95% has been achieved not requiring any chemical addition and temperature increase. Also complete electrochemical oxidation of formic acid at the original pH to CO{sub 2} and H{sub 2}O without production of intermediate has been proved by HPLC analysis. (author)

  1. Plasma membranes modified by plasma treatment or deposition as solid electrolytes for potential application in solid alkaline fuel cells.

    Science.gov (United States)

    Reinholdt, Marc; Ilie, Alina; Roualdès, Stéphanie; Frugier, Jérémy; Schieda, Mauricio; Coutanceau, Christophe; Martemianov, Serguei; Flaud, Valérie; Beche, Eric; Durand, Jean

    2012-07-30

    In the highly competitive market of fuel cells, solid alkaline fuel cells using liquid fuel (such as cheap, non-toxic and non-valorized glycerol) and not requiring noble metal as catalyst seem quite promising. One of the main hurdles for emergence of such a technology is the development of a hydroxide-conducting membrane characterized by both high conductivity and low fuel permeability. Plasma treatments can enable to positively tune the main fuel cell membrane requirements. In this work, commercial ADP-Morgane® fluorinated polymer membranes and a new brand of cross-linked poly(aryl-ether) polymer membranes, named AMELI-32®, both containing quaternary ammonium functionalities, have been modified by argon plasma treatment or triallylamine-based plasma deposit. Under the concomitant etching/cross-linking/oxidation effects inherent to the plasma modification, transport properties (ionic exchange capacity, water uptake, ionic conductivity and fuel retention) of membranes have been improved. Consequently, using plasma modified ADP-Morgane® membrane as electrolyte in a solid alkaline fuel cell operating with glycerol as fuel has allowed increasing the maximum power density by a factor 3 when compared to the untreated membrane.

  2. Solid Polymer Electrolytes Based on Functionalized Tannic Acids from Natural Resources for All-Solid-State Lithium-Ion Batteries.

    Science.gov (United States)

    Shim, Jimin; Bae, Ki Yoon; Kim, Hee Joong; Lee, Jin Hong; Kim, Dong-Gyun; Yoon, Woo Young; Lee, Jong-Chan

    2015-12-21

    Solid polymer electrolytes (SPEs) for all-solid-state lithium-ion batteries are prepared by simple one-pot polymerization induced by ultraviolet (UV) light using poly(ethylene glycol) methyl ether methacrylate (PEGMA) as an ion-conducting monomeric unit and tannic acid (TA)-based crosslinking agent and plasticizer. The crosslinking agent and plasticizer based on natural resources are obtained from the reaction of TA with glycidyl methacrylate and glycidyl poly(ethylene glycol), respectively. Dimensionally stable free-standing SPE having a large ionic conductivity of 5.6×10(-4)  Scm(-1) at room temperature can be obtained by the polymerization of PEGMA into P(PEGMA) with a very small amount (0.1 wt %) of the crosslinking agent and 2.0 wt % of the plasticizer. The ionic conductivity value of SPE with a crosslinked structure is one order of magnitude larger than that of linear P(PEGMA) in the waxy state. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  3. Plasma Membranes Modified by Plasma Treatment or Deposition as Solid Electrolytes for Potential Application in Solid Alkaline Fuel Cells

    Science.gov (United States)

    Reinholdt, Marc; Ilie, Alina; Roualdès, Stéphanie; Frugier, Jérémy; Schieda, Mauricio; Coutanceau, Christophe; Martemianov, Serguei; Flaud, Valérie; Beche, Eric; Durand, Jean

    2012-01-01

    In the highly competitive market of fuel cells, solid alkaline fuel cells using liquid fuel (such as cheap, non-toxic and non-valorized glycerol) and not requiring noble metal as catalyst seem quite promising. One of the main hurdles for emergence of such a technology is the development of a hydroxide-conducting membrane characterized by both high conductivity and low fuel permeability. Plasma treatments can enable to positively tune the main fuel cell membrane requirements. In this work, commercial ADP-Morgane® fluorinated polymer membranes and a new brand of cross-linked poly(aryl-ether) polymer membranes, named AMELI-32®, both containing quaternary ammonium functionalities, have been modified by argon plasma treatment or triallylamine-based plasma deposit. Under the concomitant etching/cross-linking/oxidation effects inherent to the plasma modification, transport properties (ionic exchange capacity, water uptake, ionic conductivity and fuel retention) of membranes have been improved. Consequently, using plasma modified ADP-Morgane® membrane as electrolyte in a solid alkaline fuel cell operating with glycerol as fuel has allowed increasing the maximum power density by a factor 3 when compared to the untreated membrane. PMID:24958295

  4. Ion beam irradiation as a tool to improve the ionic conductivity in solid polymer electrolyte systems

    Energy Technology Data Exchange (ETDEWEB)

    Manjunatha, H., E-mail: h-manjunath@blr.amrita.edu; Kumaraswamy, G. N. [Department of Physics, Amrita Vishwa Vidyapeetham, Bengaluru-560 035 (India); Damle, R. [Department of Physics, Bangalore University, Bengaluru-560 056 (India)

    2016-05-06

    Solid polymer electrolytes (SPEs) have potential applications in solid state electronic and energy devices. The optimum conductivity of SPEs required for such applications is about 10{sup −1} – 10{sup −3} Scm{sup −1}, which is hard to achieve in these systems. It is observed that ionic conductivity of SPEs continuously increase with increasing concentration of inorganic salt in the host polymer. However, there is a critical concentration of the salt beyond which the conductivity of SPEs decreases due to the formation of ion pairs. In the present study, solid polymer thin films based on poly (ethylene oxide) (PEO) complexed with NaBr salt with different concentrations have been prepared and the concentration at which ion pair formation occurs in PEO{sub x}NaBr is identified. The microstructure of the SPE with highest ionic conductivity is modified by irradiating it with low energy O{sup +1} ion (100 keV) of different fluencies. It is observed that the ionic conductivity of irradiated SPEs increases by one order in magnitude. The increase in ionic conductivity may be attributed to the enhanced segmental motion of the polymer chains due to radiation induced micro structural modification.

  5. Ionic conductivities of solid polymer electrolyte/salt systems: Group-contribution method

    Science.gov (United States)

    Joo, Jae Ho; Bae, Young Chan

    We establish a new group-contribution model based on the Nernst-Einstein equation in which the diffusion coefficient is derived from the modified double-lattice (MDL) model and the Debye-Hückel (DH) theory. The model includes the combinatorial energy contribution that is responsible for the revised Flory-Huggins entropy of mixing, the van der Waals energy contribution from dispersion, and the polar force and the specific energy contribution from hydrogen bonding. The Nernst-Einstein equation takes into account the mobility of the salt and the motion of the polymer host. To describe the segmental motion of the polymer chain, which is the well known conduction mechanism for solid polymer electrolyte (SPE) systems, the effective co-ordinated unit parameter is introduced. Our results show that good agreement is obtained upon comparison with experimental data of various PEO and salt systems in the interested ranges.

  6. Lithium Azide as an Electrolyte Additive for All-Solid-State Lithium-Sulfur Batteries.

    Science.gov (United States)

    Eshetu, Gebrekidan Gebresilassie; Judez, Xabier; Li, Chunmei; Bondarchuk, Oleksandr; Rodriguez-Martinez, Lide M; Zhang, Heng; Armand, Michel

    2017-11-27

    Of the various beyond-lithium-ion battery technologies, lithium-sulfur (Li-S) batteries have an appealing theoretical energy density and are being intensely investigated as next-generation rechargeable lithium-metal batteries. However, the stability of the lithium-metal (Li°) anode is among the most urgent challenges that need to be addressed to ensure the long-term stability of Li-S batteries. Herein, we report lithium azide (LiN3 ) as a novel electrolyte additive for all-solid-state Li-S batteries (ASSLSBs). It results in the formation of a thin, compact and highly conductive passivation layer on the Li° anode, thereby avoiding dendrite formation, and polysulfide shuttling. It greatly enhances the cycling performance, Coulombic and energy efficiencies of ASSLSBs, outperforming the state-of-the-art additive lithium nitrate (LiNO3 ). © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  7. A new percolation model for composite solid electrolytes and dispersed ionic conductors

    Science.gov (United States)

    Risyad Hasyim, Muhammad; Lanagan, Michael T.

    2018-02-01

    Composite solid electrolytes (CSEs) including conductor/insulator composites known as dispersed ionic conductors (DICs) have motivated the development of novel percolation models that describe their conductivity. Despite the long history, existing models lack in one or more key areas: (1) rigorous foundation for their physical theory, (2) explanation for non-universal conductor–insulator transition, (3) classification of DICs, and (4) extension to frequency-domain. This work describes a frequency-domain effective medium approximation (EMA) of a bond percolation model for CSEs. The EMA is derived entirely from Maxwell’s equations and contains basic microstructure parameters. The model was applied successfully to several composite systems from literature. Simulations and fitting of literature data address these key areas and illustrate the interplay between space charge layer properties and bulk microstructure.

  8. IONIC CONDUCTIVITY AND ELECTRICAL PROPERTIES OF CARBOXYMETHYL CELLULOSE - NH4Cl SOLID POLYMER ELECTROLYTES

    Directory of Open Access Journals (Sweden)

    N. H. AHMAD

    2016-06-01

    Full Text Available In this present work, carboxymethyl cellulose (CMC – ammonium chloride (NH4Cl solid polymer electrolyte (SPE films were prepared by solution casting method. The ionic conductivity and electrical properties of SPE films were investigated using Electrical Impedance Spectroscopy. SPE film containing 16 wt. % NH4Cl exhibited the highest ionic conductivity of 1.43 x 10-3 S/cm at ambient temperature, 303K. The temperature dependence SPE films showed an Arrhenius-type relation where the regression values obtained from the log conductivity versus reciprocal temperature is close to unity (R2≈1. The electrical properties have been measured as a function of frequency of Ԑr,Ԑi, Mr, Mi shown a non-Debye type behavior

  9. Nanostructured Gd-CeO2 electrolyte for solid oxide fuel cell by aqueous tape casting

    Science.gov (United States)

    Akbari-Fakhrabadi, A.; Mangalaraja, R. V.; Sanhueza, Felipe A.; Avila, Ricardo E.; Ananthakumar, S.; Chan, S. H.

    2012-11-01

    Gadolinia-doped ceria (Ce0.9Gd0.1O1.95, GDC) electrolyte was fabricated by aqueous-based tape casting method for solid oxide fuel cells (SOFCs). The ceramic powder prepared by combustion synthesis was used with poly acrylic acid (PAA), poly vinyl alcohol (PVA), poly ethylene glycol (PEG), Octanol, 2,4,7,9-tetramethyl-5-decyne-4,7-diol ethoxylate and double distilled water as dispersant, binder, plasticizer, defoamer, surfactant and solvent respectively, to prepare stable GDC slurry. The conditions for preparing stable GDC slurries were studied and optimized by sedimentation, zeta potential and viscosity measurements. Green tapes with smooth surface, flexibility, thickness in the range of 0.35-0.4 mm and 45% relative green density were prepared. Conventional and flash sintering techniques were used and compared for densification which demonstrated the possibility of surpassing sintering at high temperatures and retarding related grain growth.

  10. Dielectric and electrical behaviours of polymeric (PEO/PVP):NaIO4 composite for solid electrolytes

    Science.gov (United States)

    Marinov, Y. G.; Hadjichristov, G. B.; Petrov, A. G.; Koduru, H. K.; Marino, L.; Scaramuzza, N.

    2017-01-01

    Composite material prepared from polyethylene oxide (PEO) and polyvinylpyrrolidone (PVP) doped with Sodium (meta)periodate (NaIO4) salt was studied by complex impedance spectroscopy at room temperature. The polymers PEO and PVP were mixed in a weight ratio 70:30 %, and the concentration of the embedded NaIO4 compound was 7.5 wt.%. The effect from NaIO4 filler on the dielectric permittivity of the three-component mixed system was analyzed in the frequency range 0.1 Hz - 1 MHz. As compared with the two-component polymer host PEO/PVP, a distinctly enhanced electrical and dielectrical response and an increase of the value of dielectric constant of the polymeric (PEO/PVP):NaIO4 composite were present. This suggests the potential of this material for soft electronics and applications such as solid electrolytes.

  11. Ink-jet printing of electrolyte and anode functional layer for solid oxide fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Young, D.; Sukeshini, A.M.; Cummins, R. [Department of Mechanical and Materials Engineering, Wright State University, 3640 Colonel Glenn Highway, Dayton, OH 45430 (United States); Xiao, H. [Aerospace Power and Propulsion, UES Corp., Dayton, OH 45432 (United States); Rottmayer, M.; Reitz, T. [The Air Force Research Laboratory, Propulsion Directorate, 1950 Fifth Street, Building 18, Wright-Patterson Air Force Base, OH 45433 (United States)

    2008-09-15

    In this work, solid oxide fuel cells were fabricated by ink-jet printing. The cells were characterized in order to study the resulting microstructure and electrochemical performance. Scanning electron microscopy revealed a highly conformal 6-12 {mu}m thick dense yttria-stabilized zirconia electrolyte layer, and a porous anode-interlayer. Open circuit voltages ranged from 0.95 to 1.06 V, and a maximum power density of 0.175 W cm{sup -2} was achieved at 750 C. These results suggest that the ink-jet printing technique may be used to fabricate stable SOFC structures that are comparable to those fabricated by more conventional ceramics processing methods. This study also highlights the significance of overall cell microstructural impact on cell performance and stability. (author)

  12. Optimization of spin-coated electrodes for electrolyte-supported solid oxide fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Nobrega, Shayenne Diniz da; Monteiro, Natalia Kondo; Tabuti, Francisco; Fonseca, Fabio Coral, E-mail: shaynnedn@hotmail.com, E-mail: nataliakm@usp.br, E-mail: fntabuti@ipen.br, E-mail: fabiocf@usp.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN-CNEN/SP), Sao Paulo, SP (Brazil); Florio, Daniel Zanetti de, E-mail: daniel.florio@ufabc.edu.br [Universidade Federal do ABC (UFABC), Santo Andre, SP (Brazil)

    2017-01-15

    Electrodes for electrolyte-supported solid oxide fuel cells (SOFC’s) were fabricated by spin coating. Strontium-doped lanthanum manganite (LSM) cathode and nickel yttria-stabilized zirconia cermet anodes were synthesized and processed for enhanced deposition conditions. The influence of electrode microstructural parameters was investigated by a systematic experimental procedure aiming at optimized electrochemical performance of single cells. Polarization curves showed a strong dependence on both electrode thickness and sintering temperature. By a systematic control of such parameters, the performance of single cells was significantly enhanced due to decreasing of polarization resistance from 26 Ω cm² to 0.6 Ω cm² at 800°C. The results showed that spin-coated electrodes can be optimized for fast and cost effective fabrication of SOFCs. (author)

  13. Microwave Crystallization of Lithium Aluminum Germanium Phosphate Solid-State Electrolyte

    Directory of Open Access Journals (Sweden)

    Morsi M. Mahmoud

    2016-06-01

    Full Text Available Lithium aluminum germanium phosphate (LAGP glass-ceramics are considered as promising solid-state electrolytes for Li-ion batteries. LAGP glass was prepared via the regular conventional melt-quenching method. Thermal, chemical analyses and X-ray diffraction (XRD were performed to characterize the prepared glass. The crystallization of the prepared LAGP glass was done using conventional heating and high frequency microwave (MW processing. Thirty GHz microwave (MW processing setup were used to convert the prepared LAGP glass into glass-ceramics and compared with the conventionally crystallized LAGP glass-ceramics that were heat-treated in an electric conventional furnace. The ionic conductivities of the LAGP samples obtained from the two different routes were measured using impedance spectroscopy. These samples were also characterized using XRD and scanning electron microscopy (SEM. Microwave processing was successfully used to crystallize LAGP glass into glass-ceramic without the aid of susceptors. The MW treated sample showed higher total, grains and grain boundary ionic conductivities values, lower activation energy and relatively larger-grained microstructure with less porosity compared to the corresponding conventionally treated sample at the same optimized heat-treatment conditions. The enhanced total, grains and grain boundary ionic conductivities values along with the reduced activation energy that were observed in the MW treated sample was considered as an experimental evidence for the existence of the microwave effect in LAGP crystallization process. MW processing is a promising candidate technology for the production of solid-state electrolytes for Li-ion battery.

  14. Fabrication of All-Solid-State Lithium-ion Cells using Three-Dimensionally Structured Solid Electrolyte Li7La3Zr2O12 Pellets

    Directory of Open Access Journals (Sweden)

    MAO SHOJI

    2016-08-01

    Full Text Available All-solid-state lithium-ion batteries using Li+-ion conducting ceramic electrolytes have been focused on as attractive future batteries for electric vehicles and renewable energy conversion systems because high safety can be realized due to non-flammability of ceramic electrolytes. In addition, a higher volumetric energy density than that of current lithium-ion batteries is expected since the all-solid-state lithium-ion batteries can be made in bipolar cell configurations. However, the special ideas and techniques based on ceramic processing are required to construct the electrochemical interface for all-solid-state lithium-ion batteries since the battery development has been done so far based on liquid electrolyte system over 100 years. As one of promising approaches to develop practical all-solid-state batteries, we have been focusing on three-dimensionally (3D structured cell configurations such as an interdigitated combination of 3D pillars of cathode and anode, which can be realized by using solid electrolyte membranes with hole-array structures. The application of such kinds of 3D structures effectively increases the interface between solid electrode and solid electrolyte per unit volume, lowering the internal resistance of all-solid-state lithium-ion batteries. In this study, Li6.25Al0.25La3Zr2O12 (LLZAl, which is a Al-doped Li7La3Zr2O12 (LLZ with Li+-ion conductivity of ~10–4 S cm–1 at room temperature and high stability against lithium-metal, was used as a solid electrolyte, and its pellets with 700 um depth holes in 700 x 700 um2 area were fabricated to construct 3D-structured all-solid-state batteries with LiCoO2 / LLZAl / lithium-metal configuration. It is expected that the LiCoO2-LLZAl interface is formed by point to point contact even when the LLZAl pellet with 3D hole-array structure is applied. Therefore, the application of mechanically soft Li3BO3 with a low melting point at around 700 °C was also performed as a supporting

  15. A quasi-solid-state rechargeable lithium-oxygen battery based on a gel polymer electrolyte with an ionic liquid.

    Science.gov (United States)

    Jung, Kyu-Nam; Lee, Ji-In; Jung, Jong-Hyuk; Shin, Kyung-Hee; Lee, Jong-Won

    2014-05-28

    A quasi-solid-state lithium-oxygen battery constructed using a gel polymer electrolyte with an ionic liquid is proposed. The battery architecture incorporates a design feature that can be easily scaled up in size for use in large systems. The feasibility study demonstrates that the battery operates successfully for repeated discharge-charge cycles.

  16. A novel temperature-gradient Na±β-alumina solid electrolyte based SOx gas sensor without gaseous reference electrode

    DEFF Research Database (Denmark)

    Rao, N.; Bleek, C.M. Van den; Schoonman, J.

    1992-01-01

    An electrochemical SOx ps sensor with a tubular Na+-beta"-alumina solid electrolyte has been fabricated and tested under non-isothermal conditions. The temperature difference between the reference and working electrode of the sensor cell is about 100-degrees-C, which causes a serious deviation...

  17. Study of SEI forming process with Li BOB-DMS/SL electrolyte in first cycle

    Science.gov (United States)

    Li, Chunlei; Wang, Peng; Li, Bucheng; Li, Shiyou

    2017-10-01

    Lithium bis (oxalate) borate (Li BOB) has attracted much attention as a lithium salt or an additive in no aqueous electrolyte for lithium-ion battery. Tn this work, the formation of a solid electrolyte interphase (SET) film of sulfolane (SL) with Li BOB was studied by employment of dimethyl sulfite (DMS) as mixed solvents. When used in Li/MCMB (mesosphere carbon micro beads) cells, cell with 0.7M Li BOB-zSL/DMS (1:1) electrolyte at high temperature shows lower impedance than that at room temperature. The scanning electron microscope (SEM) results find that 0.7M Li BOB-SL/DMS (1:1) electrolyte at high temperature shows excellent film-forming characteristics than that at room temperature. The Li2SO3, ROSO2Li, Li2S, Li2CO3 substances are found in SET film by X-ray photoelectron spectroscopy (XPS). It suggests that Li BOB-SL/DMS electrolyte has an excellent solid electrolyte interphase formation capacity.

  18. Subcontract Report: Diffusion Mechanisms and Bond Dynamics in Solid Electrolyte Ion-Conductors

    Energy Technology Data Exchange (ETDEWEB)

    Zevgolis, A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hall, A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Alvez, T. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Mehmedovic, Z. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Shea, P. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Varley, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Wood, B. C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Adelstein, N. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2017-10-03

    We employ first-principles molecular dynamics simulations and Maximally Localized Wannier Function (MLWF) analysis to explore how halide substitution and nano-phase microstructures affect diffusivity, through the activation energy barrier - Ea and D0, in the solid electrolyte Li3InBr6-xClx. We find that nano-phase microstructures with x=3 (50-50 Br-Cl) mixed composition have a higher diffusivity compared to x=2 and x=3 solid solutions. There is a positive linear relationship between ln(D0.) and Ea, which suggests that for superionic conductivity optimizing both the activation energy and the D0 is important. Bond frustration due to mismatch in crystal geometry and ideal coordination number leads to especially high diffusivity through a high D0 in the x=3 composition.

  19. Quasi-solid-state dye-sensitized solar cells from hydrophobic poly(hydroxyethyl methacrylate/glycerin)/polyaniline gel electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Li, Qinghua [National Defence Key Discipline Laboratory of Light Alloy Processing Science and Technology, Nanchang Hangkong University, Nanchang 330063 (China); Tang, Qunwei, E-mail: tangqunwei@hotmail.com [Institute of Materials Science and Engineering, Ocean University of China, Shandong Province, Qingdao 266100 (China); Chen, Haiyan [Institute of Materials Science and Engineering, Ocean University of China, Shandong Province, Qingdao 266100 (China); Xu, Haitao; Qin, Yuancheng [National Defence Key Discipline Laboratory of Light Alloy Processing Science and Technology, Nanchang Hangkong University, Nanchang 330063 (China); He, Benlin, E-mail: blhe@ouc.edu.cn [Institute of Materials Science and Engineering, Ocean University of China, Shandong Province, Qingdao 266100 (China); Liu, Zhichao; Jin, Suyue; Chu, Lei [Institute of Materials Science and Engineering, Ocean University of China, Shandong Province, Qingdao 266100 (China)

    2014-04-01

    Hydrophobic poly(hydroxyethyl methacrylate/glycerin) [poly(HEMA/GR)] gel with a three-dimensional (3D) framework was successfully fabricated and employed to integrate with polyaniline (PANi). The resultant poly(HEMA/GR)/PANi gel electrolyte exhibited interconnective porous structure for holding I{sup −}/I{sub 3}{sup −}, giving a similar conduction mechanism and ionic conductivity to that of liquid system but a much enhanced retention of I{sup −}/I{sub 3}{sup −} redox couple. Fourier transform infrared spectroscopy, X-ray diffraction patterns, cyclic voltammograms as well as electrochemical impedance spectroscopy were employed to evaluate the molecular structure, crystallinity, and the electrochemical behaviors, showing that the combination of PANi with poly(HEMA/GR) caused a lower charge-transfer resistance and higher electrocatalytic activity for the I{sub 3}{sup −}/I{sup −} redox reaction in the gel electrolyte. An efficiency of 6.63% was recorded from the quasi-solid-state DSSC assembled with the poly(HEMA/GR)/PANi gel electrolyte at 100 mW cm{sup −2}. - Graphical abstract: A poly(HEMA/GR)/PANi gel electrolyte is synthesized through in situ polymerization of PANi in 3D framework of poly(HEMA/GR) hydrophobic hydrogel. The recorded ionic conductivity and electrochemical performances are significantly enhanced by integrating with PANi The resultant overall photo-to-electric conversion efficiency is 6.63%. The high ionic conductivity, along with good electrolyte retention ability, reasonable DSSC performance, low cost, simple and scalable synthesis procedure, and competitive cost, promises the electrolyte to find applications in quasi-solid-state DSSCs. - Highlights: • Poly(HEMA/GR) was employed to combine with PANi in the 3D framework. • The conductivity and electrochemical performances were enhanced. • The conversion efficiency of the quasi-solid-state DSSC was 6.63%.

  20. A system using solid ceramic oxygen electrolyte cells to measure oxygen fugacities in gas-mixing systems

    Science.gov (United States)

    Williams, R. J.; Mullins, O.

    1976-01-01

    Details are given for the construction and operation of a 101.3 kN/sq m (1 atmosphere) redox control system. A solid ceramic oxygen electrolyte cell is used to monitor the oxygen fugacity in the furnace. The system consists of a vertical quench, gas mixing furnace with heads designed for mounting the electrolyte cell and with facilities for inserting and removing the samples. The system also contains the high input impedance electronics necessary for measurements, a simplified version of a gas mixing apparatus, and devices for experiments under controlled rates of change relative to temperature and redox state. The calibration and maintenance of the system are discussed.

  1. JSC systems using solid ceramic oxygen electrolyte cells to measure oxygen fugacites in gas-mixing systems

    Science.gov (United States)

    Williams, R. J.; Mullins, O.

    1981-01-01

    Details are given for the construction and operation of a 101.3 KN/sq meter (1 atmosphere) redox control system. A solid ceramic oxygen electrolyte cell is used to monitor the oxygen fugacity in the furnace. The system consists of a vertical quench gas mixing furnace with heads designed for mounting the electrolyte cell and with facilities for inserting and removing the samples, a simplified version of a gas mixing apparatus, and devices for experiments under controlled rates of change of temperature. A thermogravimetric analysis system employing these techniques of redox control and measurement is also described. The calibration and maintenance of the system are discussed.

  2. Synthesis, characterization and electrical properties of solid electrolyte for solid oxide fuel cell; Preparacao, caracterizacao e propriedades eletricas de eletrolito solido para celula a combustivel de oxido solido

    Energy Technology Data Exchange (ETDEWEB)

    Berton, Marco Antonio Coelho; Garcia, Carlos Mario; Matos, Jeferson Hrenechen [Instituto de Tecnologia para o Desenvolvimento (LACTEC), Curitiba, PR (Brazil)], Emails: felsky@latec.org.br, garcia@latec.org.br, jeferson.h@latec.org.br

    2010-04-15

    Solid electrolytes of BaCe{sub 08}Gd{sub O29} were prepared by the polymeric precursor method. X-ray diffraction data shows a single phase with orthorhombic crystalline structure. The densification process was followed by scanning electronic microscopy and apparent density measurements. The apparent density was developed for different temperatures of sintering, reaching > 96% for sintered temperature of 1550 {sup 0}C deg . The electrochemical impedance analysis was development in the temperature of 400-700 deg C, in air atmosphere at 700 deg C a value of 30,6 mS.cm{sup -1} was obtained. The results of conductivity have confirmed the gadolinium doped barium cerate has a great potential for use as solid electrolyte for intermediate temperature solid oxide fuel cell, at experimental controlled conditions. (author)

  3. Theoretical voltammetric response of electrodes coated by solid polymer electrolyte membranes

    Energy Technology Data Exchange (ETDEWEB)

    Gómez-Marín, Ana M. [Departamento de Química y Petróleos, Universidad Nacional de Colombia, Sede Medellín, Medellín (Colombia); Hernández-Ortíz, Juan P., E-mail: jphernandezo@unal.edu.co [Departamento de Materiales, Universidad Nacional de Colombia, Sede Medellín, Medellín (Colombia); Biotechnology Center, University of Wisconsin–Madison, Madison, WI (United States)

    2014-09-24

    Highlights: • Discretized model for an interface of covered electrodes. • Two limiting behaviors are capture: double-layer and conductive interfaces. • Additional phenomena are included easily: acid/base equilibrium, ion mobility. • The model provides explanations to observed phenomena that is vaguely explained in the literature. • Implications on electrodes in fuel cells are given and it opens avenues to understand and design such systems. - Abstract: A model for the differential capacitance of metal electrodes coated by solid polymer electrolyte membranes, with acid/base groups attached to the membrane backbone, and in contact with an electrolyte solution is developed. With proper model parameters, the model is able to predict a limit response, given by Mott–Schottky or Gouy–Chapman–Stern theories depending on the dissociation degree and the density of ionizable acid/base groups. The model is also valid for other ionic membranes with proton donor/acceptor molecules as membrane counterions. Results are discussed in light of the electron transfer rate at membrane-coated electrodes for electrochemical reactions that strongly depend on the double layer structure. In this sense, the model provides a tool towards the understanding of the electro-catalytic activity on modified electrodes. It is shown that local maxima and minima in the differential capacitance as a function of the electrode potential may occur as consequence of the dissociation of acid/base molecular species, in absence of specific adsorption of immobile polymer anions on the electrode surface. Although the model extends the conceptual framework for the interpretation of cyclic voltammograms for these systems and the general theory about electrified interfaces, structural features of real systems are more complex and so, presented results only are qualitatively compared with experiments.

  4. Intermediate temperature solid oxide fuel cell based on lanthanum gallate electrolyte

    Science.gov (United States)

    Inagaki, Toru; Nishiwaki, Futoshi; Yamasaki, Satoru; Akbay, Taner; Hosoi, Kei

    The Kansai Electric Power Co. Inc. (KEPCO) and Mitsubishi Materials Corporation (MMC) have been developing intermediate temperature solid oxide fuel cells (IT-SOFCs) which are operable at a temperature range between 600 and 800 °C. There are some significant features in IT-SOFC of KEPCO-MMC: (1) highly conductive lanthanum gallate-based oxide is adopted as an electrolyte to realize high-performance disk-type electrolyte-supported cells; (2) the cell-stacks with seal-less structure using metallic separators allow residual fuel to burn around the stack and the combustion heat is utilized for thermally self-sustainable operation; (3) the separators have flexible arms by which separate compressive forces can be applied for manifold parts and interconnection parts. We are currently participating in the project by New Energy and Industrial Technology Development Organization (NEDO) to develop 10 kW-class combined heat and power (CHP) systems. In FY2006, a 10 kW-class module was developed, with which the electrical efficiency of 50%HHV was obtained based on DC 12.6 kW. In the first quarter of FY2007, the 10 kW-class CHP system using the module gave the electrical efficiency of 41%HHV on AC 10 kW and the overall efficiency of 82%HHV when exhaust heat was recovered as 60 °C hot water. Currently, the operation has been accumulated for about 2500 h to evaluate the long-term stability of the system.

  5. In Situ Generation of Poly (Vinylene Carbonate) Based Solid Electrolyte with Interfacial Stability for LiCoO2 Lithium Batteries.

    Science.gov (United States)

    Chai, Jingchao; Liu, Zhihong; Ma, Jun; Wang, Jia; Liu, Xiaochen; Liu, Haisheng; Zhang, Jianjun; Cui, Guanglei; Chen, Liquan

    2017-02-01

    Nowadays it is extremely urgent to seek high performance solid polymer electrolyte that possesses both interfacial stability toward lithium/graphitic anodes and high voltage cathodes for high energy density solid state batteries. Inspired by the positive interfacial effect of vinylene carbonate additive on solid electrolyte interface, a novel poly (vinylene carbonate) based solid polymer electrolyte is presented via a facile in situ polymerization process in this paper. It is manifested that poly (vinylene carbonate) based solid polymer electrolyte possess a superior electrochemical stability window up to 4.5 V versus Li/Li+ and considerable ionic conductivity of 9.82 × 10-5 S cm-1 at 50 °C. Moreover, it is demonstrated that high voltage LiCoO2/Li batteries using this solid polymer electrolyte display stable charge/discharge profiles, considerable rate capability, excellent cycling performance, and decent safety characteristic. It is believed that poly (vinylene carbonate) based electrolyte can be a very promising solid polymer electrolyte candidate for high energy density lithium batteries.

  6. Ionic Liquid Electrolytes for Li–Air Batteries: Lithium Metal Cycling

    Science.gov (United States)

    Grande, Lorenzo; Paillard, Elie; Kim, Guk-Tae; Monaco, Simone; Passerini, Stefano

    2014-01-01

    In this work, the electrochemical stability and lithium plating/stripping performance of N-butyl-N-methylpyrrolidinium bis(trifluoromethanesulfonyl)imide (Pyr14TFSI) are reported, by investigating the behavior of Li metal electrodes in symmetrical Li/electrolyte/Li cells. Electrochemical impedance spectroscopy measurements and galvanostatic cycling at different temperatures are performed to analyze the influence of temperature on the stabilization of the solid electrolyte interphase (SEI), showing that TFSI-based ionic liquids (ILs) rank among the best candidates for long-lasting Li–air cells. PMID:24815072

  7. Ionic liquid electrolytes for Li-air batteries: lithium metal cycling.

    Science.gov (United States)

    Grande, Lorenzo; Paillard, Elie; Kim, Guk-Tae; Monaco, Simone; Passerini, Stefano

    2014-05-08

    In this work, the electrochemical stability and lithium plating/stripping performance of N-butyl-N-methylpyrrolidinium bis(trifluoromethanesulfonyl)imide (Pyr14TFSI) are reported, by investigating the behavior of Li metal electrodes in symmetrical Li/electrolyte/Li cells. Electrochemical impedance spectroscopy measurements and galvanostatic cycling at different temperatures are performed to analyze the influence of temperature on the stabilization of the solid electrolyte interphase (SEI), showing that TFSI-based ionic liquids (ILs) rank among the best candidates for long-lasting Li-air cells.

  8. Ionic Liquid Electrolytes for Li–Air Batteries: Lithium Metal Cycling

    Directory of Open Access Journals (Sweden)

    Lorenzo Grande

    2014-05-01

    Full Text Available In this work, the electrochemical stability and lithium plating/stripping performance of N-butyl-N-methylpyrrolidinium bis(trifluoromethanesulfonylimide (Pyr14TFSI are reported, by investigating the behavior of Li metal electrodes in symmetrical Li/electrolyte/Li cells. Electrochemical impedance spectroscopy measurements and galvanostatic cycling at different temperatures are performed to analyze the influence of temperature on the stabilization of the solid electrolyte interphase (SEI, showing that TFSI-based ionic liquids (ILs rank among the best candidates for long-lasting Li–air cells.

  9. Conductivity enhancement in K{sup +}-ion conducting dry Solid Polymer Electrolyte (SPE): [PEO: KNO{sub 3}]: A consequence of KI dispersal and nano-ionic effect

    Energy Technology Data Exchange (ETDEWEB)

    Kesharwani, Priyanka; Sahu, Dinesh K.; Mahipal, Y.K.; Agrawal, R.C., E-mail: rakesh_c_agrawal@yahoo.co.in

    2017-06-01

    Flexible films of dry Solid Polymer Electrolytes (SPEs): [PEO: KNO{sub 3}] in varying salt concentrations have been hot-press cast. Salt concentration dependent conductivity study revealed two SPE films: [95PEO: 5KNO{sub 3}] and [70PEO: 30KNO{sub 3}] exhibiting relatively higher room temperature conductivity (σ{sub rt}) ∼ 2.76 × 10{sup -7} S/cm and ∼4.31 × 10{sup -7} S/cm respectively. In order to increase σ{sub rt} further, two strategies have been adopted. Firstly, fractional amount of KI has been dispersed as IInd-phase active filler into above two SPE film compositions which acted as Ist-phase host and Composite Polymer Electrolyte (CPE) films were hot-press cast. Filler particle concentration dependent conductivity study identified CPE films: [(95PEO: 5KNO{sub 3}) + 7KI] and [(70PEO: 30KNO{sub 3}) + 10 KI] as optimum conducting films with σ{sub rt} ∼ 6.15 × 10{sup -6} S/cm and ∼3.98 × 10{sup -6} S/cm respectively. σ{sub rt}-enhancement of approximately an order of magnitude was achieved by this approach. In second approach, dry powder mixture of (KNO{sub 3} + KI), in ratio that of above two CPE films, were subjected to high energy ball-milling separately for different durations prior to casting the films again. The conductivity measurements as a function of milling time identified CPE films: [(95PEO: 5KNO{sub 3}) + 7KI] and [(70PEO: 30KNO{sub 3}) + 10 KI] in which two respective (KNO{sub 3} + KI) ratios milled for 4- and 6-h, exhibited almost similar value of σ{sub rt} ∼ 2.09 × 10{sup -5} S/cm. This approach increased σ{sub rt} further by ∼3–6 fold. The reason attributed for this has been Nano–ionic effect introduced at the interphase boundaries between KNO{sub 3} and KI, as a consequence of milling. These films have been referred to as milled CPE films. Subsequently, all the optimum conducting SPE and CPE (unmilled/milled) films were subjected to various characterization studies in order to evaluate their utility in potential All

  10. High-Performance Flexible Solid-State Supercapacitor with an Extended Nanoregime Interface through in Situ Polymer Electrolyte Generation.

    Science.gov (United States)

    Anothumakkool, Bihag; Torris A T, Arun; Veeliyath, Sajna; Vijayakumar, Vidyanand; Badiger, Manohar V; Kurungot, Sreekumar

    2016-01-20

    Here, we report an efficient strategy by which a significantly enhanced electrode-electrolyte interface in an electrode for supercapacitor application could be accomplished by allowing in situ polymer gel electrolyte generation inside the nanopores of the electrodes. This unique and highly efficient strategy could be conceived by judiciously maintaining ultraviolet-triggered polymerization of a monomer mixture in the presence of a high-surface-area porous carbon. The method is very simple and scalable, and a prototype, flexible solid-state supercapacitor could even be demonstrated in an encapsulation-free condition by using the commercial-grade electrodes (thickness = 150 μm, area = 12 cm(2), and mass loading = 7.3 mg/cm(2)). This prototype device shows a capacitance of 130 F/g at a substantially reduced internal resistance of 0.5 Ω and a high capacitance retention of 84% after 32000 cycles. The present system is found to be clearly outperforming a similar system derived by using the conventional polymer electrolyte (PVA-H3PO4 as the electrolyte), which could display a capacitance of only 95 F/g, and this value falls to nearly 50% in just 5000 cycles. The superior performance in the present case is credited primarily to the excellent interface formation of the in situ generated polymer electrolyte inside the nanopores of the electrode. Further, the interpenetrated nature of the polymer also helps the device to show a low electron spin resonance and power rate and, most importantly, excellent shelf-life in the unsealed flexible conditions. Because the nature of the electrode-electrolyte interface is the major performance-determining factor in the case of many electrochemical energy storage/conversion systems, along with the supercapacitors, the developed process can also find applications in preparing electrodes for the devices such as lithium-ion batteries, metal-air batteries, polymer electrolyte membrane fuel cells, etc.

  11. Alkaline direct ethanol fuel cell performance using alkali-impregnated polyvinyl alcohol/functionalized carbon nano-tube solid electrolytes

    Science.gov (United States)

    Huang, Chien-Yi; Lin, Jia-Shiun; Pan, Wen-Han; Shih, Chao-Ming; Liu, Ying-Ling; Lue, Shingjiang Jessie

    2016-01-01

    This study investigates the application of a polyvinyl alcohol (PVA)/functionalized carbon nano-tubes (m-CNTs) composite in alkaline direct ethanol fuel cells (ADEFC). The m-CNTs are functionalized with PVA using the ozone mediation method, and the PVA composite containing the modified CNTs is prepared. Adding m-CNT into the PVA matrix enhances the alkaline uptake and the ionic conductivity of the KOH-doped electrolyte. Meanwhile, the m-CNT-containing membrane exhibited a lower swelling ratio and suppressed ethanol permeability compared to the pristine PVA film. The optimal condition for the ADEFC is determined to be under operation at an anode feed of 3 M ethanol in a 5 M KOH solution (at a flow rate of 5 cm3 min-1) with a cathode feed of moisturized oxygen (with a flow rate of 100 cm3 min-1) and the KOH-doped PVA/m-CNT electrolyte. We achieved a peak power density value of 65 mW cm-2 at 60 °C, which is the highest among the ADEFC literature data and several times higher than the proton-exchange direct ethanol fuel cells using sulfonated membrane electrolytes. Therefore, the KOH-doped PVA/m-CNT electrolyte is a suitable solid electrolyte for ADEFCs and has potential for commercialization in alkaline fuel cell applications.

  12. Comparison of cathode utilization between polymeric organodisulfide and titanium disulfide in solid polymer electrolyte rechargeable lithium cells

    Energy Technology Data Exchange (ETDEWEB)

    Ue, M. (Mitsubishi Petrochemical Co. Ltd., Tokyo (Japan). Tsukuba Reserch Centre); Visco, S.; Jonghe, L. (Lawrence Berkeley Lab., California, CA (United States))

    1993-12-05

    Cathode utilization of a polymeric organodisulfide prepared from 2,5-dimercapto-1,3,4-thiadiazole (noted as X1)was compared with that of titanium disulfide in an all-solid-state, thin film, rechargeable cell based on a solid polymer electrolyte operated at 95[degree]C. Two kinds of supporting electrolyte salts, LiCF3SO3 and LiN(CF3SO2)2, were used in polyethylene oxide (PEO) electrolytes and their performance in the cell was examined. The discharge-charge curve showed that LiCF3SO3 was inferior to LiClO4 in Li/PEO-LiX1/TiS2 cells. The cathode utilization of the polymeric organodisulfide was remarkably enhanced by the use of LiN(CF3SO2)2 instead of LiCF3SO3 in a polyethylene oxide-based electrolyte and achieved up to 80% (1.3 mAhcm[sup -2]) at a 0.5 mAhcm[sup -2] discharge rate. The cathode utilization of titanium disulfide was almost same as the polymeric organodisulfide at equivalent loading levels on a volume basis. 30 refs., 14 figs., 3 tabs.

  13. Electrolytic Production of Ti5Si3/TiC Composites by Solid Oxide Membrane Technology

    Science.gov (United States)

    Zheng, Kai; Zou, Xingli; Xie, Xueliang; Lu, Changyuan; Chen, Chaoyi; Xu, Qian; Lu, Xionggang

    2018-02-01

    This paper investigated the electrolytic production of Ti5Si3/TiC composites from TiO2/SiO2/C in molten CaCl2. The solid-oxide oxygen-ion-conducting membrane tube filled with carbon-saturated liquid tin was served as the anode, and the pressed spherical TiO2/SiO2/C pellet was used as the cathode. The electrochemical reduction process was carried out at 1273 K and 3.8 V. The characteristics of the obtained cathode products and the reaction mechanism of the electroreduction process were studied by a series of time-dependent electroreduction experiments. It was found that the electroreduction process generally proceeds through the following steps: TiO2/SiO2/C → Ti2O3, CaTiO3, Ca2SiO4, SiC → Ti5Si3, TiC. The morphology observation and the elemental distribution analysis indicate that the reaction routes for Ti5Si3 and TiC products are independent during the electroreduction process.

  14. Lithium scandium phosphate-based electrolytes for solid state lithium rechargeable microbatteries

    Energy Technology Data Exchange (ETDEWEB)

    Amatucci, G.G. (Dept. of Ceramics, Rutgers Univ., Piscataway, NJ (United States)); Safari, A. (Dept. of Ceramics, Rutgers Univ., Piscataway, NJ (United States)); Shokoohi, F.K. (Bellcore, Red Bank, NJ (United States)); Wilkens, B.J. (Bellcore, Red Bank, NJ (United States))

    1993-04-01

    Li[sub 3]Sc[sub 2](PO[sub 4])[sub 3] is a promising candidate for use as an electrolyte in solid state lithium rechargeable microbatteries due to its stability in air, ease of preparation, and resistance to dielectric breakdown. The room temperature ionic conductivity was optimized resulting in an increase of over two orders of magnitude to 3 x 10[sup -6] S/cm. The formation of Li[sub 3](Sc[sub 2-x]M[sub x])(PO[sub 4])[sub 3], where M=Al[sup 3+] of Y[sup 3+], resulted in the decrease of porosity, greater sinterability, and considerable enhancement of the ionic conductivity. Yttrium substitutions enhanced the conductivity slightly while aluminum increased the room temperature ionic conductivity to 1.5 x 10[sup -5] S/cm for x=0.4. Preliminary electron beam evaporation of Li[sub 3]Sc[sub 2](PO[sub 4])[sub 3] yielded amorphous thin films with ionic conductivity as high as 5 x 10[sup -5] S/cm and a composition of Li[sub 4.8]Sc[sub 1.4](PO[sub 4])[sub 3]. (orig.)

  15. Optical and Electrical Characteristics of Silver Ion Conducting Nanocomposite Solid Polymer Electrolytes Based on Chitosan

    Science.gov (United States)

    Aziz, Shujahadeen B.; Rasheed, Mariwan A.; Abidin, Zul H. Z.

    2017-10-01

    Optical and electrical properties of nanocomposite solid polymer electrolytes based on chitosan have been investigated. Incorporation of alumina nanoparticles into the chitosan:silver triflate (AgTf) system broadened the surface plasmon resonance peaks of the silver nanoparticles and shifted the absorption edge to lower photon energy. A clear decrease of the optical bandgap in nanocomposite samples containing alumina nanoparticles was observed. The variation of the direct-current (DC) conductivity and dielectric constant followed the same trend with alumina concentration. The DC conductivity increased by two orders of magnitude, which can be attributed to hindrance of silver ion reduction. Transmission electron microscopy was used to interpret the space-charge and blocking effects of alumina nanoparticles on the DC conductivity and dielectric constant. The ion conduction mechanism was interpreted based on the dependences of the electrical and dielectric parameters. The dependence of the DC conductivity on the dielectric constant is explained empirically. Relaxation processes associated with conductivity and viscoelasticity were distinguished based on the incomplete semicircular arcs in plots of the real and imaginary parts of the electric modulus.

  16. Grain boundary modification to suppress lithium penetration through garnet-type solid electrolyte

    Science.gov (United States)

    Hongahally Basappa, Rajendra; Ito, Tomoko; Morimura, Takao; Bekarevich, Raman; Mitsuishi, Kazutaka; Yamada, Hirotoshi

    2017-09-01

    Garnet-type solid electrolytes are one of key materials to enable practical usage of lithium metal anode for high-energy-density batteries. However, it suffers from lithium growth in pellets on charging, which causes short circuit. In this study, grain boundaries of Li6.5La3Zr1.5Ta0.5O12 (LLZT) pellets are modified with Li2CO3 and LiOH to investigate the influence of the microstructure of grain boundaries on lithium growth and to study the mechanism of the lithium growth. In spite of similar properties (relative density of ca. 96% and total ionic conductivity of 7 × 10-4 S cm-1 at 25 °C), the obtained pellets exhibit different tolerance on the short circuit. The LLZT pellets prepared from LiOH-modified LLZT powders exhibit rather high critical current density of 0.6 mA cm-2, at which short circuit occurs. On the other hand, the LLZT pellets without grain boundary modification short-circuited at 0.15 mA cm-2. Microstructural analyses by means of SEM, STEM and EIS suggest that lithium grows through interconnected open voids, and reveal that surface layers such as Li2CO3 and LiOH are not only plug voids but also facilitate the sintering of LLZT to suppress the lithium growth. The results indicate a strategy towards short-circuit-free lithium metal batteries.

  17. Mechanism for carbon direct electrochemical reactions in a solid oxide electrolyte direct carbon fuel cell

    Science.gov (United States)

    Li, Chen; Shi, Yixiang; Cai, Ningsheng

    The carbon direct electrochemical reactions in a solid oxide electrolyte direct carbon fuel cell (DCFC) are investigated experimentally with CH 4-deposited carbon at the anode as fuel. The surface morphology of the anode cross-sections is characterized using a scanning electron microscope (SEM), the elemental distribution using an energy dispersive spectrometer (EDS) and an X-ray photoelectron spectroscopy (XPS), and the deposited carbon microstructures using a Raman spectrometer. The results indicate that all the carbon deposited on the yttrium-stabilized zirconium (YSZ) particle surfaces, the Ni particle surfaces, as well as the three-phase boundary, can participate in the electrochemical reactions during the fuel cell discharging. The direct electrochemical reactions for carbon require the two conditions that the O 2- in the ionic conductor contact with a carbon reactive site and that the released electrons are conducted to the external circuit. The electrochemical reactions for the deposited carbon are most difficult on the Ni particle surfaces, easier on the YSZ particle surfaces and easiest at the three-phase boundary. Not all the carbon deposited in the anode participates in the direct electrochemical reactions. The deposited carbon and the O 2- in the YSZ react to form the double-bonded adsorbed carbonyl group C dbnd O.

  18. High temperature operation of a composite membrane-based solid polymer electrolyte water electrolyser

    Energy Technology Data Exchange (ETDEWEB)

    Antonucci, V.; Di Blasi, A.; Baglio, V.; Arico, A.S. [CNR-ITAE, Via Salita S. Lucia sopra Contesse 5, 98126 Messina (Italy); Ornelas, R.; Matteucci, F. [Tozzi Apparecchiature Elettriche SpA, Via Zuccherificio, 10-48010 Mezzano (RA) (Italy); Ledesma-Garcia, J.; Arriaga, L.G. [Centro de Investigacion y Desarrollo Tecnologico en Electroquimica, Parque Tecnologico Queretaro, Sanfandila, Pedro Escobedo, C.P. 76703 Queretaro (Mexico)

    2008-10-15

    The high temperature behaviour of a solid polymer electrolyte (SPE) water electrolyser based on a composite Nafion-SiO{sub 2} membrane was investigated and compared to that of a commercial Nafion membrane. The SPE water electrolyser performance was studied from 80 to 120{sup o}C with an operating pressure varying between 1 and 3 bar abs. IrO{sub 2} and Pt were used as oxygen and hydrogen evolution catalysts, respectively. The assemblies were manufactured by using a catalyst-coated membrane (CCM) technique. The performance was significantly better for the composite Nafion-SiO{sub 2} membrane than commercial Nafion 115. Furthermore, the composite membrane allowed suitable water electrolysis at high temperature under atmospheric pressure. The current densities were 2 and 1.2 A cm{sup -2} at a terminal voltage of 1.9 V for Nafion-SiO{sub 2} and Nafion 115, respectively, at 100{sup o}C and atmospheric pressure. By increasing the temperature up to 120{sup o}C, the performance of Nafion 115 drastically decreased; whereas, the cell based on Nafion-SiO{sub 2} membrane showed a further increase of performance, especially when the pressure was increased to 3 bar abs (2.1 A cm{sup -2} at 1.9 V). (author)

  19. Chemically durable polymer electrolytes for solid-state alkaline water electrolysis

    Science.gov (United States)

    Park, Eun Joo; Capuano, Christopher B.; Ayers, Katherine E.; Bae, Chulsung

    2018-01-01

    Generation of high purity hydrogen using electrochemical splitting of water is one of the most promising methods for sustainable fuel production. The materials to be used as solid-state electrolytes for alkaline water electrolyzer require high thermochemical stability against hydroxide ion attack in alkaline environment during the operation of electrolysis. In this study, two quaternary ammonium-tethered aromatic polymers were synthesized and investigated for anion exchange membrane (AEM)-based alkaline water electrolyzer. The membranes properties including ion exchange capacity (IEC), water uptake, swelling degree, and anion conductivity were studied. The membranes composed of all C-C bond polymer backbones and flexible side chain terminated by cation head groups exhibited remarkably good chemical stability by maintaining structural integrity in 1 M NaOH solution at 95 °C for 60 days. Initial electrochemical performance and steady-state operation performance were evaluated, and both membranes showed a good stabilization of the cell voltage during the steady-state operation at the constant current density at 200 mA/cm2. Although both membranes in current form require improvement in mechanical stability to afford better durability in electrolysis operation, the next generation AEMs based on this report could lead to potentially viable AEM candidates which can provide high electrolysis performance under alkaline operating condition.

  20. Electrode and solid electrolyte thin films for secondary lithium-ion batteries

    Science.gov (United States)

    Chen, C. H.; Kelder, E. M.; Schoonman, J.

    Electrostatic spray deposition (ESD) was employed to prepare thin layers of Li 1.2Mn 2O 4 (nominal composition) and BPO 4:0.035Li 2O for all-solid-state thin film lithium-ion batteries. The relationships between layer morphologies and deposition conditions such as solvent composition of the precursor solutions and substrate temperature were investigated. It was found that a low substrate temperature and/or high boiling point of the solvent may lead to a relatively dense structure. Reticular porous structures are formed, if films were deposited at 250°C and a mixture of 85 vol.% butyl carbitol and 15 vol.% ethanol was used as the solvent. The Li 1.2Mn 2O 4 layers, formed in the 250-400°C temperature range, were amorphous or micro-crystalline. After annealing beyond 600 °C, they could be crystallized into a spinel-structured material. Glassy BPO 4:0.035Li 2O layers could fill the pores of porous Li 1.2Mn 2O 4 layers to form a dense intermediate electrolyte layer. Thin-film rocking-chair batteries, Li 1.2Mn 2O 4|BPO 4:0.035Li 2O|Li 1.2Mn 2O 4|Al, were prepared and revealed an open-circuit voltage of about 1.2 V after charging.

  1. Development of bulk-type all-solid-state lithium-sulfur battery using LiBH{sub 4} electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Unemoto, Atsushi, E-mail: unemoto@imr.tohoku.ac.jp; Ikeshoji, Tamio [WPI-Advanced Institute for Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan); Yasaku, Syun; Matsuo, Motoaki [Institute for Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan); Nogami, Genki; Tazawa, Masaru; Taniguchi, Mitsugu [Mitsubishi Gas Chemicals Co., Ltd., 182 Tayuhama Shinwari, Kita-ku, Niigata 950-3112 (Japan); Orimo, Shin-ichi [WPI-Advanced Institute for Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan); Institute for Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan)

    2014-08-25

    Stable battery operation of a bulk-type all-solid-state lithium-sulfur battery was demonstrated by using a LiBH{sub 4} electrolyte. The electrochemical activity of insulating elemental sulfur as the positive electrode was enhanced by the mutual dispersion of elemental sulfur and carbon in the composite powders. Subsequently, a tight interface between the sulfur-carbon composite and the LiBH{sub 4} powders was manifested only by cold-pressing owing to the highly deformable nature of the LiBH{sub 4} electrolyte. The high reducing ability of LiBH{sub 4} allows using the use of a Li negative electrode that enhances the energy density. The results demonstrate the interface modification of insulating sulfur and the architecture of an all-solid-state Li-S battery configuration with high energy density.

  2. The study of effect of solid electrolyte on charge-discharge characteristics of thin-film lithium-ion batteries

    Science.gov (United States)

    Mazaletskiy, L. A.; Lebedev, M. E.; Mironenko, A. A.; Naumov, V. V.; Novozhilova, A. V.; Fedorov, I. S.; Rudy, A. S.

    2017-11-01

    Results of studies of the solid electrolyte effect on capacitance of thin-film electrodes on the basis of Si-O-Al and VxOy nanocomposites are presented. The studies were carried out by comparing the charge-discharge characteristics of two pairs of the identical electrodes, one of which was covered by LiPON film, within prototypes with two lithium electrodes - the counter and the reference electrode.

  3. Mass Transfer Studies with Submerged Impinging Jets in Closed Cylindrical Electrolytic Cell in the Presence of Solids

    Directory of Open Access Journals (Sweden)

    S. Feroz

    2008-12-01

    Full Text Available An experimental study of mass transfer in forced convective flow of fluid electrolyte through submerged jets impinging normal to the target surface in a closed cylindrical cell in the presence of solids (Porcelain beads is reported. The pertinent dynamic and geometric variables of this study are flow rate, diameter of the nozzle, height of the nozzle from the target surface and solids fraction. The mass transfer measurements, made by the electrochemical method propose empirical correlations in the impingement and decreasing coefficient regions.

  4. Grain boundary analysis and ionic conductivity of superplastic cubic zirconia for solid oxide fuel cell electrolytes

    Science.gov (United States)

    Martin, Michael Craig

    Yttrium stabilized zirconia (YSZ) is the material most commonly used for solid oxide fuel cell (SOFC) electrolytes because it has high oxygen ion conductivity at elevated temperatures. Manufacturing and sealing of the SOFC YSZ electrolyte is relatively expensive and cost could be reduced if the ceramic could be net shape formed. Methods to net shape form YSZ by superplastic deformation have been developed by introducing SiO2 as a second phase, but the impact of this approach on ionic conductivity was not known. This dissertation focuses on understanding how SiO2 affects the ionic conductivity of YSZ. The present work necessitated the design and fabrication of an appropriate impedance spectroscopy test capability and the preparation and evaluation of a matrix of samples with various silica amounts and grain sizes. Impedance spectroscopy is the figure of merit used to measure and evaluate ionic conductivity. Impedance spectroscopy at temperatures from 350 to 700°C and analytical electron microscopy were used to characterize grain boundary conductivity and grain boundary segregation of in 8 mol% yttrium cubic stabilized zirconia (8Y-CSZ). 1 to 10 wt% of silica was added as an intergranular phase. Grain growth experiments were conducted at temperatures of 1350°C to 1600°C for times from 0.1 to 100 hours. Grain boundary widths were determined from impedance spectroscopy data using a brick layer model. Average grain boundary widths were also determined from analytical electron microscopy conducted at Oak Ridge National Laboratory and the amount of yttrium and silicon segregation at grain boundaries was determined from chemical composition line scans. Results indicate that the addition of intergranular SiO2 to 8Y-CSZ leads to smaller grain size (due to grain boundary pinning) therefore increased grain boundary area and reduced total ionic conductivity. For a constant grain size, the specific grain boundary and the total ionic conductivity is not significantly affected

  5. Rational coating of Li7P3S11 solid electrolyte on MoS2 electrode for all-solid-state lithium ion batteries

    Science.gov (United States)

    Xu, R. C.; Wang, X. L.; Zhang, S. Z.; Xia, Y.; Xia, X. H.; Wu, J. B.; Tu, J. P.

    2018-01-01

    Large interfacial resistance between electrode and electrolyte limits the development of high-performance all-solid-state batteries. Herein we report a uniform coating of Li7P3S11 solid electrolyte on MoS2 to form a MoS2/Li7P3S11 composite electrode for all-solid-state lithium ion batteries. The as-synthesized Li7P3S11 processes a high ionic of 2.0 mS cm-1 at room temperature. Due to homogeneous union and reduced interfacial resistance, the assembled all-solid-state batteries with the MoS2/Li7P3S11 composite electrode exhibit higher reversible capacity of 547.1 mAh g-1 at 0.1 C and better cycling stability than the counterpart based on untreated MoS2. Our study provides a new reference for design/fabrication of advanced electrode materials for high-performance all-solid-state batteries.

  6. Thermodynamic study of solid solutions in the SnTe-AgSbTe2 system by means of EMF with solid electrolyte Ag4RbI5

    Science.gov (United States)

    Mashadieva, L. F.; Yusibov, Yu. A.; Kevser, Dzh.; Babanly, M. B.

    2017-09-01

    The results from studying the SnTe-AgSbTe2 system by means of EMF with the solid electrolyte Ag4RbI5 in the temperature range of 300-430 K are presented. The formation of a wide (≥80 mol % of AgSbTe2) region of solid solutions based on SnTe is confirmed. Partial thermodynamic functions Δ G̅, Δ H̅, and Δ S̅ of silver in alloys are calculated from the equations for the EMF temperature dependences. Based on the literature data regarding solid-phase equilibria in the Ag2Te-SnTe-Sb2Te3-Te system, potential-determining reactions are identified that allow us to calculate the standard thermodynamic formation functions and standard entropies of solid solutions (2SnTe) x (AgSbTe2)1- x ( x = 0.2, 0.4, 0.6, 0.8, and 0.9).

  7. Solid-state electrolyte sensors for rebreather applications: a preliminary investigation.

    Science.gov (United States)

    Sieber, Arne; Baumann, Rainer; Fasoulas, Stefanos; Krozer, Anatol

    2011-06-01

    Recently developed prototypes of zirconium dioxide and NASICON-based micro solid-state electrolyte oxygen (O2) and carbon dioxide (CO2) sensors were tested for their potential suitability in rebreathers. The O2 sensor has a quasi-indefinite lifetime, whilst that of the CO2 sensor is approximately 700 h. This is a preliminary report of a new technological application. The O2 sensor was tested in a small pressure chamber to a partial pressure of oxygen (PO2) of 405 kPa (4 bar). The CO2 sensor was tested up to 10 kPa CO2. The response times to a step change of pressure were measured, and cross-sensitivity for helium tested using trimix. A rebreather mouthpiece was modified so that breath-by-breath gas recordings could be observed. Power consumption to heat the sensors was measured. The O2 sensor demonstrated non-linearity, particularly above 101.3 kPa (1 bar) PO2, whereas the output of the CO2 sensor showed an inverse logarithmic relationship. Cross-sensitivity to helium was observed. The mean t90 response times were 90 (SD 10) ms for the O2 sensor, and 100 (SD 10) ms for the CO2 sensor. Breath-by-breath recordings showed slight damping of the CO2 trace due to electronic filtering. Power consumption was 1.5-2 W per sensor. The fast response times would allow accurate breath-by-breath measurement. Even though the O2 sensor has a non-linear response, measurement is possible using multi-point calibration. Further design is necessary to allow trimix to be used as the diluent. A major disadvantage is the high power consumption needed to heat the sensors to high temperatures.

  8. Toward garnet electrolyte–based Li metal batteries: An ultrathin, highly effective, artificial solid-state electrolyte/metallic Li interface

    Science.gov (United States)

    Fu, Kun (Kelvin); Gong, Yunhui; Liu, Boyang; Zhu, Yizhou; Xu, Shaomao; Yao, Yonggang; Luo, Wei; Wang, Chengwei; Lacey, Steven D.; Dai, Jiaqi; Chen, Yanan; Mo, Yifei; Wachsman, Eric; Hu, Liangbing

    2017-01-01

    Solid-state batteries are a promising option toward high energy and power densities due to the use of lithium (Li) metal as an anode. Among all solid electrolyte materials ranging from sulfides to oxides and oxynitrides, cubic garnet–type Li7La3Zr2O12 (LLZO) ceramic electrolytes are superior candidates because of their high ionic conductivity (10−3 to 10−4 S/cm) and good stability against Li metal. However, garnet solid electrolytes generally have poor contact with Li metal, which causes high resistance and uneven current distribution at the interface. To address this challenge, we demonstrate a strategy to engineer the garnet solid electrolyte and the Li metal interface by forming an intermediary Li-metal alloy, which changes the wettability of the garnet surface (lithiophobic to lithiophilic) and reduces the interface resistance by more than an order of magnitude: 950 ohm·cm2 for the pristine garnet/Li and 75 ohm·cm2 for the surface-engineered garnet/Li. Li7La2.75Ca0.25Zr1.75Nb0.25O12 (LLCZN) was selected as the solid-state electrolyte (SSE) in this work because of its low sintering temperature, stabilized cubic garnet phase, and high ionic conductivity. This low area-specific resistance enables a solid-state garnet SSE/Li metal configuration and promotes the development of a hybrid electrolyte system. The hybrid system uses the improved solid-state garnet SSE Li metal anode and a thin liquid electrolyte cathode interfacial layer. This work provides new ways to address the garnet SSE wetting issue against Li and get more stable cell performances based on the hybrid electrolyte system for Li-ion, Li-sulfur, and Li-oxygen batteries toward the next generation of Li metal batteries. PMID:28435874

  9. First-Principles Investigation of Electronic Properties in Sodium-Ion Electrolytes for Solid-State Battery Materials

    Science.gov (United States)

    Rush, Larry E., Jr.

    This thesis mainly focuses on characterizing and understanding the electronic properties of sodium-ion electrolytes using first-principles calculations. The core of these calculations is built upon a functional understanding of the relationship between quantum mechanics and the crystalline geometries that contribute to unique properties of materials such as diffusion mechanisms of ions within solid-state materials, conductivity, and ground state structures. The goal of this body of work is to understand how this relationship can give us insight into materials that might have use in an emerging field within battery technology. Sodium-ion solid-state batteries are an auspicious technology because nature has provided us with widely distributed precursor materials in such a way that removes geopolitical constraints in its construction and distribution. This is extremely important to individuals (and a collection of individuals) who want to expedite the wide use of clean and renewable energy from a societal perspective. An example is Morocco's initiative to generate 52% of its total energy consumption from clean and renewable energy sources to eliminate dependencies on foreign countries to supply energy resources. Sodium-ion solid-state batteries are an inexpensive option for large-scale grid storage, so this could play a role in providing a cost-effective option for Morocco. The challenging part is to sift through the large chemical space of sodium-ion solid-state electrolytes to find optimal materials for battery technology, and that is what motivates this body of work.

  10. Structural and electrical properties of NASICON type solid electrolyte nanoscaled glass-ceramic powder by mechanical milling for thin film batteries.

    Science.gov (United States)

    Patil, Vaishali; Patil, Arun; Yoon, Seok-Jin; Choi, Ji-Won

    2013-05-01

    During last two decades, lithium-based glasses have been studied extensively as electrolytes for solid-state secondary batteries. For practical use, solid electrolyte must have high ionic conductivity as well as chemical, thermal and electrochemical stability. Recent progresses have focused on glass electrolytes due to advantages over crystalline solid. Glass electrolytes are generally classified into two types oxide glass and sulfide glass. Oxide glasses do not react with electrode materials and this chemical inertness is advantageous for cycle performances of battery. In this study, major effort has been focused on the improvement of the ion conductivity of nanosized LiAlTi(PO4)3 oxide electrolyte prepared by mechanical milling (MM) method. After heating at 1000 degrees C the material shows good crystallinity and ionic conductivity with low electronic conductivity. In LiTi2(PO4)3, Ti4+ ions are partially substituted by Al3+ ions by heat-treatment of Li20-Al2O3-TiO2-P2O5 glasses at 1000 degrees C for 10 h. The conductivity of this material is 1.09 x 10(-3) S/cm at room temp. The glass-ceramics show fast ion conduction and low E(a) value. It is suggested that high conductivity, easy fabrication and low cost make this glass-ceramics promising to be used as inorganic solid electrolyte for all-solid-state Li rechargeable batteries.

  11. Patternable gel electrolyte infiltrated into all-solid porous Li-ion electrodes

    Science.gov (United States)

    Sun, Ke; Dillon, Shen J.

    2014-06-01

    Gel electrolyte based on 1M LiPF6 in ethylene carbonate:dimethyl carbonate, polyethyleneglycol diacrylate oligomer, and 2,2'-azobis(2-methylpropionitrile) is infiltrated into porous sintered LiCoO2 electrodes and cured in situ. The associated batteries function well, which is consistent with microscopy observations indicating that the gel electrolyte penetrates the electrode well and wets to the electrode particles. Trimethyl silyl acrylate is used to functionalize glass substrates and will cross link with polyethyleneglycol diacrylate during curing to promote bonding between the substrate and the gel electrolyte. The functionalization can localize adhesion allowing the electrolyte to easily release from unfunctionalized glass, which can be used as a mold.

  12. A solid-polymer-electrolyte direct methanol fuel cell (DMFC) with Pt ...

    Indian Academy of Sciences (India)

    polymer-electrolyte direct methanol fuel cell (DMFC) with Pt-Ru nanoparticles supported onto poly(3,4-ethylenedioxythiophene) and polystyrene sulphonic acid polymer composite as anode. K K Tintula S Pitchumani P Sridhar A K Shukla.

  13. A High Efficiency Chlorophyll Sensitized Solar Cell with Quasi Solid PVA Based Electrolyte

    Directory of Open Access Journals (Sweden)

    H. C. Hassan

    2016-01-01

    Full Text Available The objective of this work is to investigate the performance of chlorophyll sensitized solar cells (CSSCs with gel electrolyte based on polyvinyl alcohol (PVA with single iodide salt (potassium iodide (KI and double salt (KI and tetrapropylammonium iodide (TPAI. Chlorophyll was extracted from the bryophyte Hyophila involuta. The CSSC with electrolyte containing only KI salt produced a short circuit current density (Jsc of 4.59 mA cm−2, open circuit voltage (Voc of 0.61 V, fill factor (FF of 0.64, and efficiency (η of 1.77%. However, the CSSC with double salt electrolyte exhibited Jsc of 5.96 mA cm−2, Voc of 0.58 V, fill factor FF of 0.58, and η of 2.00%. Since CSSC with double salt electrolyte showed better efficiency, other cells fabricated will use the double salt electrolyte. On addition of 0.7 M tetrabutyl pyridine (TBP to the double salt electrolyte, the cell’s efficiency increased to 2.17%, Jsc=5.37 mA cm−2, Voc=0.55 V, and FF = 0.73. With 5 mM chenodeoxycholic acid (CDCA added to the chlorophyll, the light to electricity efficiency increased to 2.62% with Jsc of 8.44 mA cm−2, Voc of 0.54 V, and FF of 0.58.

  14. Phase-Field Based Multiscale Modeling of Heterogeneous Solid Electrolytes: Applications to Nanoporous Li3PS4.

    Science.gov (United States)

    Hu, Jia-Mian; Wang, Bo; Ji, Yanzhou; Yang, Tiannan; Cheng, Xiaoxing; Wang, Yi; Chen, Long-Qing

    2017-09-27

    Modeling the effective ion conductivities of heterogeneous solid electrolytes typically involves the use of a computer-generated microstructure consisting of randomly or uniformly oriented fillers in a matrix. However, the structural features of the filler/matrix interface, which critically determine the interface ion conductivity and the microstructure morphology, have not been considered during the microstructure generation. Using nanoporous β-Li3PS4 electrolyte as an example, we develop a phase-field model that enables generating nanoporous microstructures of different porosities and connectivity patterns based on the depth and the energy of the surface (pore/electrolyte interface), both of which are predicted through density functional theory (DFT) calculations. Room-temperature effective ion conductivities of the generated microstructures are then calculated numerically, using DFT-estimated surface Li-ion conductivity (3.14 × 10(-3) S/cm) and experimentally measured bulk Li-ion conductivity (8.93 × 10(-7) S/cm) of β-Li3PS4 as the inputs. We also use the generated microstructures to inform effective medium theories to rapidly predict the effective ion conductivity via analytical calculations. When porosity approaches the percolation threshold, both the numerical and analytical methods predict a significantly enhanced Li-ion conductivity (1.74 × 10(-4) S/cm) that is in good agreement with experimental data (1.64 × 10(-4) S/cm). The present phase-field based multiscale model is generally applicable to predict both the microstructure patterns and the effective properties of heterogeneous solid electrolytes.

  15. A Newly Designed Composite Gel Polymer Electrolyte Based on Poly(Vinylidene Fluoride-Hexafluoropropylene) (PVDF-HFP) for Enhanced Solid-State Lithium-Sulfur Batteries.

    Science.gov (United States)

    Xia, Yan; Wang, Xiuli; Xia, Xinhui; Xu, Ruochen; Zhang, Shengzhao; Wu, Jianbo; Liang, Yanfei; Gu, Changdong; Tu, Jiangping

    2017-10-26

    Developing high-performance solid-state electrolytes is crucial for the innovation of next-generation lithium-sulfur batteries. Herein, a facile method for preparation of a novel gel polymer electrolyte (GPE) based on poly(vinylidene fluoride-hexafluoropropylene) (PVDF-HFP) is reported. Furthermore, Li1.5 Al0.5 Ti1.5 (PO4 )3 (LATP) nanoparticles as the active fillers are uniformly embedded into the GPE to form the final PVDF-HFP/LATP composite gel polymer electrolyte (CPE). Impressively, the obtained CPE demonstrates a high lithium ion transference number of 0.51 and improved electrochemical stability as compared to commercial liquid electrolyte. In addition, the assembled solid-sate Li-S battery with the composite gel polymer electrolyte membrane presents a high initial capacity of 918 mAh g-1 at 0.05 C, and better cycle performance than the counterparts with liquid electrolyte. Our designed PVDF-HFP/LATP composite can be a promising electrolyte for next-generation solid-state batteries with high cycling stability. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  16. Effect of proton-conduction in electrolyte on electric efficiency of multi-stage solid oxide fuel cells

    Science.gov (United States)

    Matsuzaki, Yoshio; Tachikawa, Yuya; Somekawa, Takaaki; Hatae, Toru; Matsumoto, Hiroshige; Taniguchi, Shunsuke; Sasaki, Kazunari

    2015-01-01

    Solid oxide fuel cells (SOFCs) are promising electrochemical devices that enable the highest fuel-to-electricity conversion efficiencies under high operating temperatures. The concept of multi-stage electrochemical oxidation using SOFCs has been proposed and studied over the past several decades for further improving the electrical efficiency. However, the improvement is limited by fuel dilution downstream of the fuel flow. Therefore, evolved technologies are required to achieve considerably higher electrical efficiencies. Here we present an innovative concept for a critically-high fuel-to-electricity conversion efficiency of up to 85% based on the lower heating value (LHV), in which a high-temperature multi-stage electrochemical oxidation is combined with a proton-conducting solid electrolyte. Switching a solid electrolyte material from a conventional oxide-ion conducting material to a proton-conducting material under the high-temperature multi-stage electrochemical oxidation mechanism has proven to be highly advantageous for the electrical efficiency. The DC efficiency of 85% (LHV) corresponds to a net AC efficiency of approximately 76% (LHV), where the net AC efficiency refers to the transmission-end AC efficiency. This evolved concept will yield a considerably higher efficiency with a much smaller generation capacity than the state-of-the-art several tens-of-MW-class most advanced combined cycle (MACC). PMID:26218470

  17. Micromold methods for fabricating perforated substrates and for preparing solid polymer electrolyte composite membranes

    Energy Technology Data Exchange (ETDEWEB)

    Mittelsteadt, Cortney; Argun, Avni; Laicer, Castro; Willey, Jason

    2017-08-08

    In polymer electrolyte membrane (PEM) fuel cells and electrolyzes, attaining and maintaining high membrane conductivity and durability is crucial for performance and efficiency. The use of low equivalent weight (EW) perfluorinated ionomers is one of the few options available to improve membrane conductivity. However, excessive dimensional changes of low EW ionomers upon application of wet/dry or freeze/thaw cycles yield catastrophic losses in membrane integrity. Incorporation of ionomers within porous, dimensionally-stable perforated polymer electrolyte membrane substrates provides improved PEM performance and longevity. The present invention provides novel methods using micromolds to fabricate the perforated polymer electrolyte membrane substrates. These novel methods using micromolds create uniform and well-defined pore structures. In addition, these novel methods using micromolds described herein may be used in batch or continuous processing.

  18. Application of atmospheric-pressure plasma jet processed carbon nanotubes to liquid and quasi-solid-state gel electrolyte supercapacitors

    Science.gov (United States)

    Kuok, Fei-Hong; Kan, Ken-Yuan; Yu, Ing-Song; Chen, Chieh-Wen; Hsu, Cheng-Che; Cheng, I.-Chun; Chen, Jian-Zhang

    2017-12-01

    We use a dc-pulse nitrogen atmospheric-pressure plasma jet (APPJ) to calcine carbon nanotubes (CNTs) pastes that are screen-printed on carbon cloth. 30-s APPJ treatment can efficiently oxidize and vaporize the organic binders, thereby forming porous structures. As indicated by X-ray photoelectron spectroscopy (XPS) and electron probe microanalysis (EPMA), the oxygen content decreases after APPJ treatment owing to the oxidation and vaporization of ethyl cellulose, terpineol, and ethanol. Nitrogen doping was introduced to the materials by the nitrogen APPJ. APPJ-calcination improves the wettability of the CNTs printed on carbon cloth, as evidenced by water contact angle measurement. Raman spectroscopy indicates that reactive species of nitrogen APPJ react violently with CNTs in only 30-s APPJ processing time and introduce defects and/or surface functional groups on CNTs. Carbon cloths with calcined CNT layers are used as electrodes for liquid and quasi-solid-state electrolyte supercapacitors. Under a cyclic voltammetry test with a 2 mV/s potential scan rate, the specific capacitance is 73.84 F/g (areal capacitance = 5.89 mF/cm2) with a 2 M KCl electrolyte and 66.47 F/g (areal capacitance = 6.10 mF/cm2) with a H2SO4/polyvinyl alcohol (PVA) gel electrolyte.

  19. Polypropylene oil as fuel for solid oxide fuel cell with samarium doped-ceria (SDC)-carbonate as electrolyte

    Science.gov (United States)

    Syahputra, R. J. E.; Rahmawati, F.; Prameswari, A. P.; Saktian, R.

    2017-03-01

    The research focusses on converting polypropylene oil as pyrolysis product of polypropylene plastic into an electricity. The converter was a direct liquid fuel-solid oxide fuel cell (SOFC) with cerium oxide based material as electrolyte. The polypropylene vapor flowed into fuel cell, in the anode side and undergo oxidation reaction, meanwhile, the Oxygen in atmosphere reduced into oxygen ion at cathode. The fuel cell test was conducted at 400 - 600 °C. According to GC-MS analysis, the polypropylene oil consist of C8 to C27 hydrocarbon chain. The XRD analysis result shows that Na2CO3 did not change the crystal structure of SDC even increases the electrical conductivity. The maximum power density is 0.079 mW.cm-2 at 773 K. The open circuite voltage is 0.77 volt. Chemical stability test by analysing the single cell at before and after fuel cell test found that ionic migration occured during fuel cell operation. It is supported by the change of elemental composition in the point position of electrolyte and at the electrolyte-electrode interface

  20. Ionic conductivity and dielectric permittivity of PEO-LiClO4 solid polymer electrolyte plasticized with propylene carbonate

    Directory of Open Access Journals (Sweden)

    S. Das

    2015-02-01

    Full Text Available We have studied ionic conductivity and dielectric permittivity of PEO-LiClO4 solid polymer electrolyte plasticized with propylene carbonate. Differential scanning calorimetry and X-ray diffraction studies confirm minimum volume fraction of crystalline phase for the polymer electrolyte with 40 wt. % propylene carbonate. The ionic conductivity exhibits a maximum for the same composition. The temperature dependence of the ionic conductivity has been well interpreted using Vogel-Tamman-Fulcher equation. Ion-ion interactions in the polymer electrolytes have been studied using Raman spectra and the concentrations of free ions, ion-pairs and ion-aggregates have been determined. The ionic conductivity increases due to the increase of free ions with the increase of propylene carbonate content. But for higher content of propylene carbonate, the ionic conductivity decreases due to the increase of concentrations of ion-pairs and ion-aggregates. To get further insights into the ion dynamics, the experimental data for the complex dielectric permittivity have been studied using Havriliak–Negami function. The variation of relaxation time with temperature obtained from this formalism follows Vogel-Tamman-Fulcher equation similar to the ionic conductivity.

  1. Effects of grain boundaries at the electrolyte/cathode interfaces on oxygen reduction reaction kinetics of solid oxide fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Min Gi; Koo, Ja Yang; Ahn, Min Woo; Lee, Won Young [Dept. of Mechanical Engineering, Sungkyunkwan University, Suwon (Korea, Republic of)

    2017-04-15

    We systematically investigated the effects of grain boundaries (GBs) at the electrolyte/cathode interface of two conventional electrolyte materials, i.e., yttria-stabilized zirconia (YSZ) and gadolinia-doped ceria (GDC). We deposited additional layers by pulsed laser deposition to control the GB density on top of the polycrystalline substrates, obtaining significant improvements in peak power density (two-fold for YSZ and three-fold for GDC). The enhanced performance at high GB density in the additional layer could be ascribed to the accumulation of oxygen vacancies, which are known to be more active sites for oxygen reduction reactions (ORR) than grain cores. GDC exhibited a higher enhancement than YSZ, due to the easier formation, and thus higher concentration, of oxygen vacancies for ORR. The strong relation between the concentration of oxygen vacancies and the surface exchange characteristics substantiated the role of GBs at electrolyte/cathode interfaces on ORR kinetics, providing new design parameters for highly performing solid oxide fuel cells.

  2. Improved transport property of proton-conducting solid oxide fuel cell with multi-layered electrolyte structure

    Science.gov (United States)

    Shimada, Hiroyuki; Yamaguchi, Toshiaki; Sumi, Hirofumi; Nomura, Katsuhiro; Yamaguchi, Yuki; Fujishiro, Yoshinobu

    2017-10-01

    A multi-layered electrolyte structure is proposed for proton-conducting solid oxide fuel cells (SOFCs) to achieve higher power density and higher open-circuit voltage (OCV). Although recent proton-conducting SOFCs have demonstrated high power density, their OCVs have been lower than that of conventional SOFCs with stabilized zirconia because proton-conducting oxides intrinsically have electron-hole conduction. The proposed electrolyte structure has a porous BaZr0.1Ce0.7Y0.1Yb0.1O3-δ (BZCYYb) layer deposited on a dense BZCYYb layer. This structure effectively improves both cathode polarization and ionic transport property, resulting in higher power density with higher OCV. Also, discussion based on an equivalent circuit model of proton-conducting SOFCs clearly reveals a mechanism that determines OCV, namely, higher ohmic resistance and lower electrode polarization resistance lead to higher OCV. Our results suggest that higher electrode performance is essential for proton-conducting SOFCs to achieve higher OCV, particularly in the case of anode-supported configurations with thin electrolyte.

  3. Reorientation of Magnetic Graphene Oxide Nanosheets in Crosslinked Quaternized Polyvinyl Alcohol as Effective Solid Electrolyte

    Directory of Open Access Journals (Sweden)

    Jia-Shuin Lin

    2016-11-01

    Full Text Available This work aims to clarify the effect of magnetic graphene oxide (GO reorientation in a polymer matrix on the ionic conduction and methanol barrier properties of nanocomposite membrane electrolytes. Magnetic iron oxide (Fe3O4 nanoparticles were prepared and dispersed on GO nanosheets (GO-Fe3O4. The magnetic GO-Fe3O4 was imbedded into a quaternized polyvinyl alcohol (QPVA matrix and crosslinked (CL- with glutaraldehyde (GA to obtain a polymeric nanocomposite. A magnetic field was applied in the through-plane direction during the drying and film formation steps. The CL-QPVA/GO-Fe3O4 nanocomposite membranes were doped with an alkali to obtain hydroxide-conducting electrolytes for direct methanol alkaline fuel cell (DMAFC applications. The magnetic field-reoriented CL-QPVA/GO-Fe3O4 electrolyte demonstrated higher conductivity and lower methanol permeability than the unoriented CL-QPVA/GO-Fe3O4 membrane or the CL-QPVA film. The reoriented CL-QPVA/GO-Fe3O4 nanocomposite was used as the electrolyte in a DMAFC and resulted in a maximum power density of 55.4 mW·cm−2 at 60 °C, which is 73.7% higher than that of the composite without the magnetic field treatment (31.9 mW·cm−2. In contrast, the DMAFC using the CL-QPVA electrolyte generated only 22.4 mW·cm−2. This research proved the surprising benefits of magnetic-field-assisted orientation of GO-Fe3O4 in facilitating the ion conduction of a polymeric electrolyte.

  4. Record-low sintering-temperature (600 °C) of solid-oxide fuel cell electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Dasari, Hari Prasad, E-mail: energyhari@nitk.edu.in [High-Temperature Energy Materials Research Center, Korea Institute of Science and Technology, Seoul 136-791 (Korea, Republic of); Chemical Engineering Department, National Institute of Technology Karnataka, Mangalore 575025, Karnataka (India); Ahn, Kiyong; Park, Sun-Young; Hong, Jongsup; Kim, Hyoungchul; Yoon, Kyung Joong; Son, Ji-Won; Kim, Byung-Kook; Lee, Hae-Weon [High-Temperature Energy Materials Research Center, Korea Institute of Science and Technology, Seoul 136-791 (Korea, Republic of); Lee, Jong-Ho, E-mail: jongho@kist.re.kr [High-Temperature Energy Materials Research Center, Korea Institute of Science and Technology, Seoul 136-791 (Korea, Republic of)

    2016-07-05

    One of the major problems arising with Solid-Oxide Fuel Cell (SOFC) electrolyte is conventional sintering which requires a very high temperature (>1300 °C) to fully density the electrolyte material. In the present study, the sintering temperature of SOFC electrolyte is drastically decreased down to 600 °C. Combinational effects of particle size reduction, liquid-phase sintering mechanism and microwave sintering resulted in achieving full density in such a record-low sintering temperature. Gadolinium doped Ceria (GDC) nano-particles are synthesized by co-precipitation method, Lithium (Li), as an additional dopant, is used as liquid-phase sintering aid. Microwave sintering of this electrolyte material resulted in decreasing the sintering temperature to 600 °C. Micrographs obtained from Scanning/Transmission Electron Microscopy (SEM/TEM) clearly pointed a drastic growth in grain-size of Li-GDC sample (∼150 nm) than compared to GDC sample (<30 nm) showing the significance of Li addition. The sintered Li-GDC samples displayed an ionic conductivity of ∼1.00 × 10{sup −2} S cm{sup −1} at 600 °C in air and from the conductivity plots the activation energy is found to be 0.53 eV. - Highlights: • Sintering temperature is drastically decreased to 600 °C. • Key factors: Particle size reduction, liquid-phase and microwave sintering. • Nano-Li-GDC sample has ionic conductivity of ∼1.00 × 10{sup −2} S cm{sup −1} at 600 °C in air.

  5. Effect of Poly(Ether Urethane) Introduction on the Performance of Polymer Electrolyte for All-Solid-State Dye-Sensitized Solar Cells

    Science.gov (United States)

    Zhou, Yan-Fang; Xiang, Wan-Chun; Fang, Shi-Bi; Chen, Shen; Zhou, Xiao-Wen; Zhang, Jing-Bo; Lin, Yuan

    2009-12-01

    The introduction of poly(ether urethane) (PEUR) into polymer electrolyte based on poly(ethylene oxide), LiI and I2, has significantly increased the ionic conductivity by nearly two orders of magnitudes. An increment of I-3 diffusion coefficient is also observed. All-solid-state dye-sensitized solar cells are constructed using the polymer electrolytes. It was found that PEUR incorporation has a beneficial effect on the enhancement of open circuit voltage Voc by shifting the band edge of TiO2 to a negative value. Scanning electron microscope images indicate the perfect interfacial contact between the TiO2 electrode and the blend electrolyte.

  6. Estimation of energy density of Li-S batteries with liquid and solid electrolytes

    Science.gov (United States)

    Li, Chunmei; Zhang, Heng; Otaegui, Laida; Singh, Gurpreet; Armand, Michel; Rodriguez-Martinez, Lide M.

    2016-09-01

    With the exponential growth of technology in mobile devices and the rapid expansion of electric vehicles into the market, it appears that the energy density of the state-of-the-art Li-ion batteries (LIBs) cannot satisfy the practical requirements. Sulfur has been one of the best cathode material choices due to its high charge storage (1675 mAh g-1), natural abundance and easy accessibility. In this paper, calculations are performed for different cell design parameters such as the active material loading, the amount/thickness of electrolyte, the sulfur utilization, etc. to predict the energy density of Li-S cells based on liquid, polymeric and ceramic electrolytes. It demonstrates that Li-S battery is most likely to be competitive in gravimetric energy density, but not volumetric energy density, with current technology, when comparing with LIBs. Furthermore, the cells with polymer and thin ceramic electrolytes show promising potential in terms of high gravimetric energy density, especially the cells with the polymer electrolyte. This estimation study of Li-S energy density can be used as a good guidance for controlling the key design parameters in order to get desirable energy density at cell-level.

  7. Thermodynamic stability of Ca{sub 3}TeO{sub 6} determined by a solid electrolyte EMF method

    Energy Technology Data Exchange (ETDEWEB)

    Sukhomlinov, D., E-mail: dmitry.sukhomlinov@aalto.fi [Aalto University School of Chemical Technology, Department of Materials Science and Engineering, Metallurgical Thermodynamics and Modeling Research Group, Vuorimiehentie 2 K, PO Box 16200, FI-00076 Aalto (Finland); Tesfaye, F. [Aalto University School of Chemical Technology, Department of Materials Science and Engineering, Metallurgical Thermodynamics and Modeling Research Group, Vuorimiehentie 2 K, PO Box 16200, FI-00076 Aalto (Finland); Åbo Akademi University, Process Chemistry Centre, Piispankatu 8, FI-20500 Turku (Finland); Taskinen, P. [Aalto University School of Chemical Technology, Department of Materials Science and Engineering, Metallurgical Thermodynamics and Modeling Research Group, Vuorimiehentie 2 K, PO Box 16200, FI-00076 Aalto (Finland)

    2015-09-10

    Highlights: • Gibbs energy of formation of Ca{sub 3}TeO{sub 6} experimentally determined for the first time. • Oxygen concentration galvanic cells based on YSZ solid electrolyte were employed. • In the Ca–Te–O system, Ca{sub 3}TeO{sub 6} coexists with CaO and Te. - Abstract: The standard thermodynamic properties of Ca{sub 3}TeO{sub 6} were determined electrochemically utilizing fast O{sup 2−} ion conducting solid electrolyte yttria-stabilized zirconia. The ternary phase was synthesized from the pure oxides CaO and TeO{sub 2} in excess of CaO. The electromotive force measurements were performed on two similar electrochemical cells of the type Te + CaO + Ca{sub 3}TeO{sub 6}|YSZ|O{sub 2}, within the temperature range from 850 to 949 K. The standard Gibbs energy of formation for the ternary compound Ca{sub 3}TeO{sub 6} was determined for the first time, based on the experimental data obtained.

  8. Effect of epoxidation level on thermal properties and ionic conductivity of epoxidized natural rubber solid polymer nanocomposite electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Harun, Fatin; Chan, Chin Han; Winie, Tan [Faculty of Applied Sciences, UniversitiTeknologi MARA (UiTM), Shah Alam, 40450 Selangor Darul Ehsan (Malaysia); Sim, Lai Har; Zainal, Nurul Fatahah Asyqin [Center of Foundation Studies, PuncakAlam Campus, UniversitiTeknologi MARA, 40430 Selangor Darul Ehsan (Malaysia)

    2015-08-28

    Effect of epoxide content on the thermal and conductivity properties of epoxidized natural rubber (ENR) solid polymer nanocomposite electrolytes was investigated. Commercial available epoxidized natural rubber having 25 (ENR25) and 50 mole% (ENR50) epoxide, respectively were incorporated with lithium perchlorate (LiClO{sub 4}) salt and titanium dioxide (TiO{sub 2}) nanofiller via solution casting method. The solid polymer nanocomposite electrolytes were characterized by differential scanning calorimetry (DSC) and impedance spectroscopy (IS) for their thermal properties and conductivity, respectively. It was evident that introduction of LiClO{sub 4} causes a greater increase in glass transition temperature (T{sub g}) and ionic conductivity of ENR50 as compared to ENR25. Upon addition of TiO{sub 2} in ENR/LiClO{sub 4} system, a remarkable T{sub g} elevation was observed for both ENRs where ENR50 reveals a more pronounced changes. It is interesting to note that they exhibit different phenomenon in ionic conductivity with TiO{sub 2} loading where ENR25 shows enhancement of conductivity while ENR50 shows declination.

  9. Nanocomposite semi-solid redox ionic liquid electrolytes with enhanced charge-transport capabilities for dye-sensitized solar cells.

    Science.gov (United States)

    Rutkowska, Iwona A; Marszalek, Magdalena; Orlowska, Justyna; Ozimek, Weronika; Zakeeruddin, Shaik M; Kulesza, Pawel J; Grätzel, Michael

    2015-08-10

    The ability of Pt nanostructures to induce the splitting of the II bond in iodine (triiodide) molecules is explored here to enhance electron transfer in the iodine/iodide redox couple. Following the dispersal of Pt nanoparticles at 2 % (weight) level, charge transport was accelerated in triiodide/iodide-containing 1,3-dialkylimidazolium room-temperature ionic liquid. If both Pt nanoparticles and multi-walled carbon nanotubes were introduced into the ionic-liquid-based system, a solid-type (nonfluid) electrolyte was obtained. By using solid-state voltammetric (both sandwich-type and microelectrode-based) methodology, the apparent diffusion coefficients for charge transport increased to approximately 1×10(-6)  cm(2)  s(-1) upon the incorporation of the carbon-nanotube-supported iodine-modified Pt nanostructures. A dye-sensitized solar cell comprising TiO2 covered with a heteroleptic Ru(II) -type sensitizer (dye) and the semisolid triiodide/iodide ionic liquid electrolyte admixed with carbon-nanotube-supported Pt nanostructures yielded somewhat higher power conversion efficiencies (up to 7.9 % under standard reporting conditions) than those of the analogous Pt-free system. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Reducing Interfacial Resistance between Garnet-Structured Solid-State Electrolyte and Li-Metal Anode by a Germanium Layer.

    Science.gov (United States)

    Luo, Wei; Gong, Yunhui; Zhu, Yizhou; Li, Yiju; Yao, Yonggang; Zhang, Ying; Fu, Kun Kelvin; Pastel, Glenn; Lin, Chuan-Fu; Mo, Yifei; Wachsman, Eric D; Hu, Liangbing

    2017-06-01

    Substantial efforts are underway to develop all-solid-state Li batteries (SSLiBs) toward high safety, high power density, and high energy density. Garnet-structured solid-state electrolyte exhibits great promise for SSLiBs owing to its high Li-ion conductivity, wide potential window, and sufficient thermal/chemical stability. A major challenge of garnet is that the contact between the garnet and the Li-metal anodes is poor due to the rigidity of the garnet, which leads to limited active sites and large interfacial resistance. This study proposes a new methodology for reducing the garnet/Li-metal interfacial resistance by depositing a thin germanium (Ge) (20 nm) layer on garnet. By applying this approach, the garnet/Li-metal interfacial resistance decreases from ≈900 to ≈115 Ω cm(2) due to an alloying reaction between the Li metal and the Ge. In agreement with experiments, first-principles calculation confirms the good stability and improved wetting at the interface between the lithiated Ge layer and garnet. In this way, this unique Ge modification technique enables a stable cycling performance of a full cell of lithium metal, garnet electrolyte, and LiFePO4 cathode at room temperature. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  11. Excellent stability of a lithium-ion-conducting solid electrolyte upon reversible Li(+) /H(+) exchange in aqueous solutions.

    Science.gov (United States)

    Ma, Cheng; Rangasamy, Ezhiylmurugan; Liang, Chengdu; Sakamoto, Jeffrey; More, Karren L; Chi, Miaofang

    2015-01-02

    Batteries with an aqueous catholyte and a Li metal anode have attracted interest owing to their exceptional energy density and high charge/discharge rate. The long-term operation of such batteries requires that the solid electrolyte separator between the anode and aqueous solutions must be compatible with Li and stable over a wide pH range. Unfortunately, no such compound has yet been reported. In this study, an excellent stability in neutral and strongly basic solutions was observed when using the cubic Li7 La3 Zr2 O12 garnet as a Li-stable solid electrolyte. The material underwent a Li(+) /H(+) exchange in aqueous solutions. Nevertheless, its structure remained unchanged even under a high exchange rate of 63.6 %. When treated with a 2 M LiOH solution, the Li(+) /H(+) exchange was reversed without any structural change. These observations suggest that cubic Li7 La3 Zr2 O12 is a promising candidate for the separator in aqueous lithium batteries. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  12. Ionic Borate-Based Covalent Organic Frameworks: Lightweight Porous Materials for Lithium-Stable Solid State Electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Black, Hayden T; Harrison, Katharine Lee

    2016-10-01

    The synthesis and characterization of the first polyelectrolyte of intrinsic microporosity (PEIM) is described. The novel material was synthesized via reaction between the nitrile group in the polymer backbone and n-butyl lithium, effectively anchoring an imine anion to the porous framework while introducing a mobile lithium counterion. The PEIM was characterized by 13C, 1H, and 7Li NMR experiments, revealing quantitative conversion of the nitrile functionality to the anionic imine. Variable temperature 7Li NMR analysis of the dry PEIM and the electrolyteswollen PEIM revealed that lithium ion transport within the dry PEIM was largely due to interchain hopping of the Li+ ions, and that the mobility of polymer associated Li+ was reduced after swelling in electrolyte solution. Meanwhile, the swollen PEIM supported efficient transport of dissolved Li+ within the expanded pores. These results are discussed in the context of developing novel solid or solid-like lithium ion electrolytes using the new PEIM material.

  13. In situ electron holography of electric potentials inside a solid-state electrolyte: Effect of electric-field leakage

    Energy Technology Data Exchange (ETDEWEB)

    Aizawa, Yuka; Yamamoto, Kazuo; Sato, Takeshi [Nanostructures Research Laboratory, Japan Fine Ceramics Center, 2-4-1 Mutsuno, Atsuta-ku, Nagoya, Aichi 456-8587 (Japan); Murata, Hidekazu [Faculty of Science and Technology, Meijo University, 1-501 Shiogamaguchi, Tempaku-ku, Nagoya, Aichi 468-8502 (Japan); Yoshida, Ryuji; Fisher, Craig A.J. [Nanostructures Research Laboratory, Japan Fine Ceramics Center, 2-4-1 Mutsuno, Atsuta-ku, Nagoya, Aichi 456-8587 (Japan); Kato, Takehisa; Iriyama, Yasutoshi [Department of Materials, Physics and Energy Engineering, Nagoya University, Furo-cho, Chikusa-ku, Nagoya, Aichi 464-8601 (Japan); Hirayama, Tsukasa, E-mail: t-hirayama@jfcc.or.jp [Nanostructures Research Laboratory, Japan Fine Ceramics Center, 2-4-1 Mutsuno, Atsuta-ku, Nagoya, Aichi 456-8587 (Japan)

    2017-07-15

    In situ electron holography is used to observe changes of electric-potential distributions in an amorphous lithium phosphorus oxynitride (LiPON) solid-state electrolyte when different voltages are applied. 2D phase images are simulated by integrating the 3D potential distribution along the electron trajectory through a thin Cu/LiPON/Cu region. Good agreement between experimental and simulated phase distributions is obtained when the influence of the external electric field is taken into account using the 3D boundary-charge method. Based on the precise potential changes, the lithium-ion and lithium-vacancy distributions inside the LiPON layer and electric double layers (EDLs) are inferred. The gradients of the phase drops at the interfaces in relation to EDL widths are discussed. - Highlights: • Solid-state electrolyte LiPON has been observed by in situ electron holography. • Observed phase distributions are compared with those simulated numerically. • 3D electric fields around the specimen are taken into account in the simulation. • Electric-potential distributions inside LiPON have been obtained. • The lithium-ion and lithium-vacancy distributions inside the LiPON are inferred.

  14. Enhancement of the ionic conductivity and the amorphous state of solid polymer electrolytes for rechargeable lithium batteries

    Energy Technology Data Exchange (ETDEWEB)

    Bischoff, H. (Dresden Univ. of Technology, Inst. of Physical Chemistry and Electrochemistry (Germany)); Rahner, D. (Dresden Univ. of Technology, Inst. of Physical Chemistry and Electrochemistry (Germany)); Wiesener, K. (Dresden Univ. of Technology, Inst. of Physical Chemistry and Electrochemistry (Germany)); Steurich, T. (Merseburg Univ., Inst. of Macromolecular Chemistry (Germany)); Sandner, R. (Merseburg Univ., Inst. of Macromolecular Chemistry (Germany))

    1993-04-15

    Complexes of LiCF[sub 3]SO[sub 3] and a polymer obtained by polymerization of triethylene glycol dimethacrylate (TRGDMA) and its copolymerization with acrylonitrile (AN) at molar ratios of 0.67, 2.0 and 4.0, both in the presence of poly(ethylene glycol) dimethylether as a plasticizer, provides a.c. conductivities in the range between 10[sup -5] and 10[sup -4] S/cm at ambient temperature. An increase of conductivities has been found at growing ratios of AN:TRGDMA from 0 to 2.0 and molar ratios of ethylene oxide (EO) units:LiCF[sub 3]SO[sub 3] ranging from 12 to about 26. The conductivity is nearly independent of the content of AN at EO:Li[sup +] = 52. Impedance measurements of cells modified with these solid electrolytes show that the electrochemical behaviour of the composite lithium/PEO-lithium salt-complex is determined by the properties of the phase boundary metal/solid electrolyte. The mechanical stability of the polymer, acting simultaneously as a separator between the active electrodes, determines the cycle life. (orig.)

  15. A High Temperature Electrochemical Energy Storage System Based on Sodium Beta-Alumina Solid Electrolyte (Base)

    Energy Technology Data Exchange (ETDEWEB)

    Anil Virkar

    2008-03-31

    This report summarizes the work done during the period September 1, 2005 and March 31, 2008. Work was conducted in the following areas: (1) Fabrication of sodium beta{double_prime} alumina solid electrolyte (BASE) using a vapor phase process. (2) Mechanistic studies on the conversion of {alpha}-alumina + zirconia into beta{double_prime}-alumina + zirconia by the vapor phase process. (3) Characterization of BASE by X-ray diffraction, SEM, and conductivity measurements. (4) Design, construction and electrochemical testing of a symmetric cell containing BASE as the electrolyte and NaCl + ZnCl{sub 2} as the electrodes. (5) Design, construction, and electrochemical evaluation of Na/BASE/ZnCl{sub 2} electrochemical cells. (6) Stability studies in ZnCl{sub 2}, SnCl{sub 2}, and SnI{sub 4} (7) Design, assembly and testing of planar stacks. (8) Investigation of the effect of porous surface layers on BASE on cell resistance. The conventional process for the fabrication of sodium ion conducting beta{double_prime}-alumina involves calcination of {alpha}-alumina + Na{sub 2}CO{sub 3} + LiNO{sub 3} at 1250 C, followed by sintering powder compacts in sealed containers (platinum or MgO) at {approx}1600 C. The novel vapor phase process involves first sintering a mixture of {alpha}-alumina + yttria-stabilized zirconia (YSZ) into a dense ceramic followed by exposure to soda vapor at {approx}1450 C to convert {alpha}-alumina into beta{double_prime}-alumina. The vapor phase process leads to a high strength BASE, which is also resistant to moisture attack, unlike BASE made by the conventional process. The PI is the lead inventor of the process. Discs and tubes of BASE were fabricated in the present work. In the conventional process, sintering of BASE is accomplished by a transient liquid phase mechanism wherein the liquid phase contains NaAlO{sub 2}. Some NaAlO{sub 2} continues to remain at grain boundaries; and is the root cause of its water sensitivity. In the vapor phase process, Na

  16. Oxides with polyatomic anions considered as new electrolyte materials for solid oxide fuel cells (SOFCs)

    Energy Technology Data Exchange (ETDEWEB)

    Bin Hassan, Oskar Hasdinor

    2010-10-21

    Materials with Polyatomic anions of [Al{sub 2}O{sub 7}]{sup -8}, [Ti{sub 2}O{sub 8}]{sup -8} and [P{sub 2}O{sub 7}]{sup -4} were investigated with respect to their ionic conductivity properties as well as its thermal expansion properties with the aim to use them as SOFCs electrolytes. The polyatomic anion groups selected from the oxy-cuspidine family of Gd{sub 4}Al{sub 2}O{sub 9} and Gd{sub 4}Ti{sub 2}O{sub 10} as well as from pyrophosphate SnP{sub 2}O{sub 7}. The pure oxy-cuspidine Gd{sub 4}Al{sub 2}O{sub 9}, the series of Gd{sub 4}Al{sub 2-x}Mg{sub x}O{sub 9-x/2} with x=0.10-1.0 and Gd{sub 4-x}M{sub x}Al{sub 2}O{sub 9-x/2} (M=Ca, Sr) with x = 0.05-0.5 were prepared successfully by the citrate complexation method. All samples showed the crystal structure of monoclinic oxycuspidine structure with space group of P2{sub 1/c} and Z=4. No solid solution was observed for Gd{sub 4}Al{sub 2-x}Mg{sub x}O{sub 9-x/2} where additional phases of Gd{sub 2}O{sub 3} and MgO were presence. XRD semiquantitative analysis together with SEM-EDX analysis revealed that Mg{sup 2+} was not able to substitute the Al{sup 3+} ions even at low Mg{sup 2+} concentration. The solid solution limit of Gd{sub 4-x}Ca{sub x}Al{sub 2}O{sub 9-x/2} and Gd{sub 4-x}Sr{sub x}Al{sub 2}O{sub 9-x/2} was determined between 0.05-0.10 and 0.01-0.05 mol for Ca and Sr, respectively. Beyond the substitution limit Gd{sub 4}Al{sub 2}O{sub 9}, GdAlO{sub 3} and SrGd{sub 2}Al{sub 2}O{sub 7} appeared as additional phases. The highest electrical conductivity obtained at 900 C yielded {sigma}= 1.49 x 10{sup -4}Scm{sup -1} for Gd{sub 3.95}Ca{sub 0.05}Al{sub 2}O{sub 8.98}. In comparison, the conductivity of pure Gd{sub 4}Al{sub 2}O{sub 9} was {sigma}= 1.73 x 10{sup -5} Scm{sup -1}. The conductivities determined were in a similar range as those of other cuspidine materials investigated previously. The thermal expansion coefficient of Gd{sub 4}Al{sub 2}O{sub 9} at 1000 C was 7.4 x 10{sup -6}K{sup -1}. The earlier reported

  17. In situ gelation of Al(III)-4-tert-butylpyridine based metal-organic gel electrolyte for efficient quasi-solid-state dye-sensitized solar cells

    Science.gov (United States)

    Dong, Yu-Jie; Rao, Hua-Shang; Cao, Yang; Chen, Hong-Yan; Kuang, Dai-Bin; Su, Cheng-Yong

    2017-03-01

    A novel Al(III)-4-tert-butylpyridine (TBP) gel electrolyte is successfully achieved by a simple and facile in situ gelation method and applied as quasi-solid-state electrolyte for dye-sensitized solar cells (DSSCs). Through directly adding Al3+ into the TBP solution, the induced hydrolysis of Al3+ and the coordination interaction between Al3+ and TBP facilitates the formation of metal-organic gels(MOGs), in which such bi-functional TBP molecules will act as both gelators and active additives to tailor the performance of electrolytes. In addition, the gel electrolytes can largely preserve the properties of liquid electrolyte and penetrate well into the TiO2 photoanode film. Both Al3+ and TBP in the gel electrolytes affect the performance of cells. The Jsc of gel electrolytes decrease with the increasing concentration of gelators due to the enhanced strength and viscosity of the gel electrolytes, while the competition between Al3+ and TBP causes conduction band edge shift and electron recombination, leading to a variation of Voc. Herein, by tuning the molar ratio of Al3+/TBP, an impressive conversion efficiency of 8.25% is obtained, indicating a promising protocol of preparing MOGs not only to achieve high performance in solar cells, but also opens up extended scopes in other energy-related fields such as catalysis.

  18. Effects of pored separator films at the anode and cathode sides on concentration changes of electrolyte salt in lithium ion batteries

    Science.gov (United States)

    Yamanaka, Toshiro; Nakagawa, Hiroe; Tsubouchi, Shigetaka; Domi, Yasuhiro; Doi, Takayuki; Abe, Takeshi; Ogumi, Zempachi

    2017-12-01

    The concentration change of ions in the electrolyte solution in deep narrow spaces between electrodes in batteries was studied by in situ multi-probe Raman spectroscopy. When two separator films were placed at the anode and cathode sides, the concentration change became greater, suggesting that the resistance for ion migration at the anode side increased more than that at the cathode side. Thus, there seems to be a concerted effect of the surface film at the anode [solid electrolyte interphase (SEI)] and the adjacent separator film to form an effective diffusion barrier for Li+.

  19. Ab initio investigation of ground-states and ionic motion in particular in zirconia-based solid-oxide electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Hirschfeld, Julian Arndt

    2012-12-11

    Electrolytes with high ionic conductivity at lower temperatures are the prerequisite for the success of Solid Oxide Fuel Cells (SOFC). One candidate is doped zirconia. In the past, the electrical resistance of zirconia based SOFC electrolytes has mainly been decreased by reducing its thickness. But there are limits to reducing the thickness and one can say that nowadays the normal ways are basically exhausted to further enhance the conductivity of well-known electrolyte materials. Hence, new approaches need to be found to discover windows of enhanced ionic conductivity. This can be achieved by understanding the quantum-mechanical oxygen transport in unconventional configurations of doped zirconia. Therefore, such an understanding is of fundamental importance. In this thesis two approaches are pursued, the investigation of the strain dependent ionic migration in zirconia based electrolytes and the designing of an electrolyte material structure with enhanced and strongly anisotropic ionic conductivity. The first approach expands the elementary understanding of oxygen migration in oxide lattices. The migration barrier of the oxygen ion jumps in zirconia is determined by applying the Density Functional Theory (DFT) calculations in connection with the Nudged Elastic Band (NEB) method. These computations show an unexpected window of decreased migration barriers at high compressive strains. Similar to other publications a decrease in the migration barrier for expansive strain is observed. But, in addition, a migration barrier decrease under high compressive strains is found beyond a maximal height of the migration barrier. A simple analytic model offers an explanation. The drop of the migration barrier at high compressions originates from the elevation of the ground-state energy. This means: Increasing ground state energies becomes an interesting alternative to facilitate ionic mobility. The second approach is based on the idea, that actually, only in the direction of ion

  20. Preparation and characterization of solid electrolytes for solid oxide fuel cells. Quarterly report, July 1--September 30, 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-31

    During this quarter, the authors have analyzed EXAFS spectra of rare earth doped ceria and identified Gd and Sm doped ceria electrolytes for further investigations in this project. Although electrical properties of the material have been examined in detail, very little work has considered the microstructural/property relationships, particularly in relationship to atomic and geometric structures of these ceria based oxides. The authors have observed an ionic conductivity of 8.3 {times} 10{sup {minus}2} S/Cm in the (CeO{sub 2}){sub 0.8}(GdO{sub 1.5}){sub 0.2} at 800 C which is approximately four times that of Y{sub 2}O{sub 3} doped ZrO{sub 3} doped ZrO{sub 2} at the same temperature. The fraction of Ce{sup +4} ions reduced to Ce{sup +3} as a function of temperature and oxygen partial pressure. The partial reduction of cerium oxide generates mobile electrons and causes electronic conductivity in the electrolyte at temperatures above 500 C. In this quarter, the authors have attempted to measure the microstructural properties using SEM, TEM and HVC STM techniques. Other parts of this investigation are also discussed.

  1. Study and development of a hydrogen/oxygen fuel cell in solid polymer electrolyte technology

    Energy Technology Data Exchange (ETDEWEB)

    Mosdale, R.

    1992-10-29

    The hydrogen/oxygen fuel cell appears today as the best candidate to the replacing of the internal combustion engine for automobile traction. This system uses the non explosive electrochemical recombination of hydrogen and oxygen. It is a clean generator whom only reactive product is water. This thesis shows a theoretical study of this system, the synthesis of different kinds of used electrodes and finally an analysis of water movements in polymer electrolyte by different original technologies. 70 refs., 73 figs., 15 tabs.

  2. Fuel Cells Using the Protic Ionic Liquid and Rotator Phase Solid Electrolyte Principles

    Science.gov (United States)

    2008-02-13

    Talk “High temperature Polymer Electrolyte Membrane Fuel Cells ( HT -PEMFCs) for Portable Power in Large-Scale Energy Storage Devices”, Paper Number 195...Protic ionic liquids and the PEM fuel cell , 2nd International Congress on Ionic Liquids, poster session, #3P07-081, Yokohama, Japan, August 5-10...Membrane Fuel Cells ( HT -PEMFCs) for Portable Power in Large-Scale Energy Storage Devices”, Paper Number 195, 212th Meeting of the Electrochemical

  3. A novel polysulfide hydrogel electrolyte based on low molecular mass organogelator for quasi-solid-state quantum dot-sensitized solar cells

    Science.gov (United States)

    Huo, Zhipeng; Tao, Li; Wang, Shimao; Wei, Junfeng; Zhu, Jun; Dong, Weiwei; Liu, Feng; Chen, Shuanghong; Zhang, Bing; Dai, Songyuan

    2015-06-01

    A quasi-solid-state quantum dot-sensitized solar cell (QDSSC) is fabricated by using 12-hydroxystearic acid as a low molecular mass organogelator to gelate the polysulfide electrolyte. Noticeably, the gel to liquid transition temperature of this polysulfide hydrogel electrolyte is 96 °C, which contributes to the long-term stability of the quasi-solid-state QDSSC (QS-QDSSC). The influences of gelation on the charge transport, electron recombination and photovoltaic performance of the QS-QDSSC are investigated by electrochemical impedance spectroscopy. Moreover, the network of the hydrogel is investigated by the Field emission scanning electron microscopy and polarized optical light microscopy. It is found that the charge transport is influenced by the network in the hydrogel electrolyte, and the accelerated electron recombination at the photoanode/electrolyte interface leads to the decreased open-circuit voltage. The QS-QDSSC exhibits an energy conversion efficiency of 2.40% at AM 1.5 (100 mW cm-2) which is slightly lower than that of liquid electrolyte based cell (2.88%). However, the QS-QDSSC exhibits significantly improved stability during the accelerated thermal test. Especially, during the accelerated aging test, the short-circuit current density (Jsc) of the liquid electrolyte based QDSSC sharply decreased to nearly 35% of its initial value, while there is relatively less change in the Jsc for the QS-QDSSC.

  4. Highly efficient solid-state dye-sensitized solar cells based on hexylimidazolium iodide ionic polymer electrolyte prepared by in situ low-temperature polymerization

    Science.gov (United States)

    Wang, Guiqiang; Yan, Chao; Zhang, Juan; Hou, Shuo; Zhang, Wei

    2017-03-01

    Solid-state dye-sensitized solar cells (DSCs) are fabricated using a novel ionic polymer electrolyte containing hexylimidazolium iodide (HII) ionic polymer prepared by in situ polymerization of N,N‧-bis(imidazolyl) hexane and 1,6-diiodohexane without an initiator at low temperature (40 °C). The as-prepared HII ionic polymer has a similar structure to alkylimidazolium iodide ionic liquid, and the imidazolium cations are contained in the polymer main chain; so, it can act simultaneously as the redox mediator in the electrolyte. By incorporating an appropriate amount of 1,3-dimethylimidazolium iodide (DMII) in HII ionic polymer (DMII/HII ionic polymer = 0.7:1, weight ratio), the conductivity of the ionic polymer electrolyte is greatly improved due to the formation of Grotthuss bond exchange. In addition, in situ synthesis of ionic polymer electrolyte guarantees a good pore-filling of the electrolyte in the TiO2 photoanode. As a result, the solid-state DSC based on the ionic polymer electrolyte containing HII ionic polymer and DMII without iodine achieves a conversion efficiency of 6.55% under the illumination of 100 mW cm-2 (AM 1.5), which also exhibits a good at-rest stability at room temperature.

  5. Composite electrolytes of polyethylene oxides/garnets interfacially wetted by ionic liquid for room-temperature solid-state lithium battery

    Science.gov (United States)

    Huo, Hanyu; Zhao, Ning; Sun, Jiyang; Du, Fuming; Li, Yiqiu; Guo, Xiangxin

    2017-12-01

    Paramount attention has been paid on solid polymer electrolytes due to their potential in enhancement of energy density as well as improvement of safety. Herein, the composite electrolytes consisting of Li-salt-free polyethylene oxides and 200 nm-sized Li6.4La3Zr1.4Ta0.6O12 particles interfacially wetted by [BMIM]TF2N of 1.8 μL cm-2 have been prepared. Such wetted ionic liquid remains the solid state of membrane electrolytes and decreases the interface impedance between the electrodes and the electrolytes. There is no release of the liquid phase from the PEO matrix when the pressure of 5.0 × 104 Pa being applied for 24 h. The interfacially wetted membrane electrolytes show the conductivity of 2.2 × 10-4 S cm-1 at 20 °C, which is one order of magnitude greater than that of the membranes without the wetted ionic liquids. The conduction mechanism is related to a large number of lithium ions releasing from Li6.4La3Zr1.4Ta0.6O12 particles and the improved conductive paths along the ion-liquid-wetted interfaces between the polymer matrix and ceramic grains. When the membranes being used in the solid-state LiFePO4/Li and LiFe0.15Mn0.85PO4/Li cells at 25 °C, the excellent rate capability and superior cycle stability has been shown. The results provide a new prospect for solid polymer electrolytes used for room-temperature solid-state lithium batteries.

  6. Stable quasi-solid-state dye-sensitized solar cell using ionic gel electrolyte with low molecular mass organogelator

    Energy Technology Data Exchange (ETDEWEB)

    Tao, Li [Key Laboratory of Novel Thin Film Solar Cells, Division of Solar Energy Materials and Engineering, Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Huo, Zhipeng, E-mail: zhipenghuo@163.com [Key Laboratory of Novel Thin Film Solar Cells, Division of Solar Energy Materials and Engineering, Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Dai, Songyuan, E-mail: sydai@ncepu.edu.cn [Key Laboratory of Novel Thin Film Solar Cells, Division of Solar Energy Materials and Engineering, Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Beijing Key Lab of Novel Thin Film Solar Cells, North China Electric Power University, Beijing 102206 (China); Zhu, Jun; Zhang, Changneng; Pan, Xu; Huang, Yang [Key Laboratory of Novel Thin Film Solar Cells, Division of Solar Energy Materials and Engineering, Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Yang, Shangfeng [Hefei National Laboratory for Physical Sciences at Microscale, Department of Materials Science and Engineering, University of Science and Technology of China (USTC), Hefei 230026 (China); Zhang, Bing; Yao, Jianxi [Beijing Key Lab of Novel Thin Film Solar Cells, North China Electric Power University, Beijing 102206 (China)

    2015-02-15

    Long-term stability is essential for the application and commercialization of dye-sensitized solar cells (DSCs). A quasi-solid-state DSC (QS-DSC) with excellent long-term stability is fabricated using ionic gel electrolyte (IGE) with N,N′-methylenebisdodecanamide as low molecular mass organogelator (LMOG). The gel to solution transition temperature (T{sub gel}) of this IGE is 127 °C, well above the working temperature of the device, which contributes to the thermal properties of the IGE and the device. The electrochemical properties of the IGE and the kinetic processes of electron transport and recombination of the QS-DSC are investigated by means of electrochemical impedance spectroscopy (EIS) and controlled intensity modulated photocurrent/photovoltage spectroscopy (IMPS/IMVS). Due to the obstructed diffusion of redox species caused by the network of IGE, the electron recombination at the TiO{sub 2} photoelectrode/electrolyte interface in the QS-DSC is accelerated. More importantly, compared with the ionic liquid electrolyte (ILE) based DSC, the QS-DSC based on the IGE exhibits excellent thermal and light-soaking stabilities during the accelerated aging tests for 1000 h. Especially, there is almost no degradation in the short-circuit current density (J{sub sc}) in the IGE based QS-DSC, while the J{sub sc} of the ILE based DSC decreased to 85–94% of their initial values. - Highlights: • A novel IGE with high T{sub gel} is obtained by using a diamide derivative as LMOG. • The IGE based QS-DSC is very stable during the accelerated aging tests. • The influences of gelation on the electron kinetic processes are investigated.

  7. Ionic conductivity measurement in magnesium aluminate spinel and solid state galvanic cell with magnesium aluminate electrolyte

    Science.gov (United States)

    Lee, Myongjai

    This thesis work is about the experimental measurement of electronic and ionic conductivities in the MgAl2O4 spinel at 500˜600°C range and exploring the fundamental origin of solid-state galvanic cell behavior in the cell of Al|MgAl2O4|Mg, Al|MgAl2O 4|C, and Mg|MgAl2O4|C, in which at least one metal electrode in common with the composition of the electrolyte. For the electronic conductivity measurement, we have used the ion-blocking Gold and Carbon electrodes which are inert with both Mg and Al ions to suppress the ionic conduction from the total conduction. DC polarization method was used to measure the conduction through Au|MgAl2O4|Au and C|MgAl2O4|C specimens. The measured electrical conductivity using Au|MgAl2O4|Au and C|MgAl2O4|C specimens showed 10-9.3 ˜ 10-8.4 (O·cm) -1 at 600˜720°C range following the Arrhenius-type relation. These conductivity data are in agreement with reported data obtained from Pt and Ag ion-blocking electrodes deposited on MgAl2O4 specimens. For the ionic conductivity measurement, we have used the non-blocking Al and Mg electrodes for Al and Mg ionic conductivities, respectively. Ionic conductivity measurement of Al and Mg in separate manner has not been reported yet. In both Al|MgAl2O4|Al and Mg|MgAl2O 4|Mg specimens, gradual increase of conduction was observed once at the initial period before it reaches the steady state conduction. By DC method on the range of 580˜650°C, steady state Al ionic conductivity was measured from Al|MgAl2O4|Al specimen showing 10 -7.7 ˜ 10-6.8 (O·cm)-1 with the activation energy of 1.9eV in sigma = sigma0 exp-QRT formula. There was no difference in the conductivity by the change of the atmosphere from 5%H2 + 95%N2 mixed gas to pure Ar gas. So it was confirmed that the oxygen defect chemistry did not play a role. For Mg ionic conductivity Mg|MgAl2O4|Mg specimen was used and the measured conductivity shows 10-6.7 ˜ 10-4.4 (O·cm)-1 at 400˜550°C with the activation energy of 1.44eV at Ar gas

  8. Low molecular mass organogelator based gel electrolyte with effective charge transport property for long-term stable quasi-solid-state dye-sensitized solar cells.

    Science.gov (United States)

    Huo, Zhipeng; Dai, Songyuan; Zhang, Changneng; Kong, Fantai; Fang, Xiaqin; Guo, Lei; Liu, Weiqing; Hu, Linhua; Pan, Xu; Wang, Kongjia

    2008-10-16

    Stable quasi-solid-state dye-sensitized solar cells (DSC) were fabricated using 12-hydroxystearic acid as a low molecular mass organogelator (LMOG) to form gel electrolyte. TEM image of the gel exhibited the self-assembled network constructed by the LMOG, which hindered flow and volatilization of the liquid. The formation of less-mobile polyiodide ions such as I 3 (-) and I 5 (-) confirmed by Raman spectroscopy increased the conductivity of the gel electrolytes by electronic conduction process, which should be rationalized by the Grotthuss-type electron exchange mechanism caused by rather packed polyiodide species in the electrolytes. The results of the accelerated aging tests showed that the gel electrolyte based dye-sensitized solar cell could retain over 97% of its initial photoelectric conversion efficiency value after successive heating at 60 degrees C for 1000 h and device degradation was also negligible after one sun light soaking with UV cutoff filter for 1000 h.

  9. Highly conductive quasi-coaxial electrospun quaternized polyvinyl alcohol nanofibers and composite as high-performance solid electrolytes

    Science.gov (United States)

    Liao, Guan-Ming; Li, Pin-Chieh; Lin, Jia-Shiun; Ma, Wei-Ting; Yu, Bor-Chern; Li, Hsieh-Yu; Liu, Ying-Ling; Yang, Chun-Chen; Shih, Chao-Ming; Lue, Shingjiang Jessie

    2016-02-01

    Electrospun quaternized polyvinyl alcohol (Q-PVA) nanofibers are prepared, and a potassium hydroxide (KOH)-doped nanofiber mat demonstrates enhanced ionic conductivity compared with a dense Q-PVA film with KOH doping. The Q-PVA composite containing 5.98% electrospun Q-PVA nanofibers exhibits suppressed methanol permeability. Both the high conductivity and suppressed methanol permeability are attributed to the quasi-coaxial structure of the electrospun nanofibers. The core of the fibers exhibits a more amorphous region that forms highly conductive paths, while the outer shell of the nanofibers contains more polymer crystals that serve as a hard sheath surrounding the soft core. This shell induces mass transfer resistance and creates a tortuous fuel pathway that suppresses methanol permeation. Such a Q-PVA composite is an effective solid electrolyte that makes the use of alkaline fuel cells viable. In a direct methanol alkaline fuel cell operated at 60 °C, a peak power density of 54 mW cm-2 is obtained using the electrospun Q-PVA composite, a 36.4% increase compared with a cell employing a pristine Q-PVA film. These results demonstrate that highly conductive coaxial electrospun nanofibers can be prepared through a single-opening spinneret and provide a possible approach for high-performance electrolyte fabrication.

  10. Development of novel strategies for enhancing the cycle life of lithium solid polymer electrolyte batteries. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Macdonald, Digby D.; Urquidi-Macdonald, Mirna; Allcock, Harry; Engelhard, George; Bomberger, N.; Gao, L.; Olmeijer, D.

    2001-04-30

    Lithium/solid polymer electrolyte (Li/SPE) secondary batteries are under intense development as power sources for portable electronic devices as well as electric vehicles. These batteries offer high specific energy, high energy density, very low self-discharge rates, and flexibility in packaging; however, problems have inhibited their introduction into the marketplace. This report summarizes findings to examine processes that occur with Li/SPE secondary batteries upon cyclic charging/discharging. The report includes a detailed analysis of the impedance measured on the Li/SPE/IC and IC/SPE/IC systems. The SPE was a derivative of methoxyethoxyethoxyphosphazene (MEEP) with lithium triflate salt as the electrolyte, while the intercalated cathodes (IC) comprised mixtures of manganese dioxide, carbon powder, and MEEP as a binder. Studies on symmetrical Li/SPE/Li laminates show that cycling results in a significant expansion of the structure over the first few tens of cycles; however, no corresponding increase in the impedance was noted. The cycle life of the intercalation cathode was found to be very sensitive to the method of fabrication. Results indicate that the cycle life is due to the failure of the IC, not to the failure of the lithium/SPE interface. A pattern recognition neural network was developed to predict the cycle life of a battery from the charge/discharge characteristics.

  11. Development of complex hydride-based all-solid-state lithium ion battery applying low melting point electrolyte

    Science.gov (United States)

    Suzuki, Shohei; Kawaji, Jun; Yoshida, Koji; Unemoto, Atsushi; Orimo, Shin-ichi

    2017-08-01

    A thermally durable all-solid-state lithium ion battery composed of a complex hydride, oxide electrolytes, and LiNi1/3Mn1/3Co1/3O2 active material is developed. This battery exhibits a discharge capacity of 56 mAh g-1, and the tenth capacity retention ratio is 29% at 150 °C owing to the large contact resistance between the electrolyte layer and the composite positive electrode layer. This large contact resistance is reduced by introducing an adhesive layer comprised of a mixture of LiBH4 and LiNH2 that is easily melted by thermal treatment and fills the voids and pores at the interface between the two layers. As a result, repeated charge-discharge cycles are successfully demonstrated at 150 °C with a high discharge capacity and discharge capacity retention ratio. The first discharge capacity is enhanced to 114 mAh g-1 and the capacity retention ratio at the tenth cycle is improved to 71%. These results demonstrate that using an adhesive layer is an effective measure to reduce the contact resistance and thereby enhance the performance of the battery.

  12. Performance of Electrolyte Supported Solid Oxide Fuel Cells with STN Anodes

    DEFF Research Database (Denmark)

    Veltzé, Sune; Reddy Sudireddy, Bhaskar; Jørgensen, Peter Stanley

    2013-01-01

    high fuel utilization and redox cycling have been performed to identify the performance limiting parameters in this new type of full ceramic SOFCs. Measured performances and stability have been further tentatively linked to modifications of the nano-sized infiltrates within the anode.......In order to replace the state of the art Ni-cermet as SOFC anode, electrolyte supported cells comprising CGO/Ni infiltrated Nbdoped SrTiO3 anodes, and LSM/YSZ cathodes have been developed and tested as single 5 x 5 cm2 cells. The initial performance reached 0.4 W/cm2 at 850 C. Further tests under...

  13. Lithium ion conducting electrolytes

    Science.gov (United States)

    Angell, Charles Austen; Liu, Changle; Xu, Kang; Skotheim, Terje A.

    1999-01-01

    The present invention relates generally to highly conductive alkali-metal ion non-crystalline electrolyte systems, and more particularly to novel and unique molten (liquid), rubbery, and solid electrolyte systems which are especially well suited for use with high current density electrolytic cells such as primary and secondary batteries.

  14. Lithium ion conducting electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Angell, C.A.; Liu, C.; Xu, K.; Skotheim, T.A.

    1999-10-05

    The present invention relates generally to highly conductive alkali-metal ion non-crystalline electrolyte systems, and more particularly to novel and unique molten (liquid), rubbery, and solid electrolyte systems which are especially well suited for use with high current density electrolytic cells such as primary and secondary batteries.

  15. The effect of isocyanate structure on ionic conductivity of waste cooking oil based polyurethane solid polymer electrolyte

    Science.gov (United States)

    Kamarulzaman, N. A.; Tahir, S. M.

    2017-09-01

    Polyurethane solid polymer electrolyte (SPE) films was prepared via solvent-free method using waste cooking oil-based polyol, diisocyanate, LiTFSI salt and ethylene carbonate as plasticizer. Two types of diisocyanate were chosen; aromatic 4,4-diphenylmethane diisocyanate (MDI) and aliphatic 1,6-hexamethylene diisocyanate (HDI) and the effect of diisocyanate structure on SPE properties were characterized using Fourier Transform Infrared Spectroscopy (FTIR), Electrochemical Impedance Spectroscopy (EIS), Differential Scanning Calorimetry (DSC) and X-Ray Diffractometry (XRD). The highest ionic conductivity achieved was 5.76 × 10-6 S cm-1 using MDI. This was supported with lower crystallinity observed by decrease in peaks intensity in XRD. The findings indicated that aromatic diisocyanate is more suitable to produce polyurethane SPE.

  16. One-pot liquid phase synthesis of (100-x)Li3PS4-xLiI solid electrolytes

    Science.gov (United States)

    Phuc, Nguyen Huu Huy; Hirahara, Eito; Morikawa, Kei; Muto, Hiroyuki; Matsuda, Atsunori

    2017-10-01

    (100-x)Li3PS4-xLiI solid electrolytes are successfully prepared using a simple process proposed in this study. The results show that the heat-treatment process plays a crucial role in the formation of the final product. In the case of x = 33.3%, 2Li3PS4-1LiI, a nearly pure crystalline phase of Li7P2S8I (LPSI), is obtained. The cyclic voltammogram result and DC polarization curves indicate that the interfacial layer between LPSI and the Li metal is stable. Li2S, LiI, Li5P, Li4P2S6, and some unknown substances were detected in the interfacial layer by XRD.

  17. Nickel and its alloys as perspective materials for intermediate temperature steam electrolysers operating on proton conducting solid acids as electrolyte

    DEFF Research Database (Denmark)

    Nikiforov, Aleksey; Petrushina, Irina; Jensen, Jens Oluf

    2012-01-01

    Several stainless steels, nickel-based alloys, Ta-coated stainless steel, niobium, nickel, platinum and gold were evaluated as possible materials for use in the intermediate temperature water electrolysers. The corrosion resistance was measured in molten KH2PO4 as simulated conditions corresponding...... plates and cell housing. It was shown, that nickel, high-nickel alloys and austenitic stainless steels containing small amounts of Ti have high corrosion resistance in this media. © The Electrochemical Society....... to protonconducting solid acids or transition metal phosphates as electrolytes. It was shown that Au is subject to corrosion in molten KH 2PO4 during polarisation. However, Ni and Ta-coated stainless steel (AISI 316L) demonstrated high corrosion stability and can be recommended as a construction material for bipolar...

  18. Effect of Zirconium Oxide Nanofiller and Dibutyl Phthalate Plasticizer on Ionic Conductivity and Optical Properties of Solid Polymer Electrolyte

    Directory of Open Access Journals (Sweden)

    Siti Mariah Mohd Yasin

    2014-01-01

    Full Text Available New solid polymer electrolytes (SPE based on poly(ethylene oxide (PEO doped with lithium trifluoromethanesulfonate (LiCF3SO3, dibutyl phthalate (DBP plasticizer, and zirconium oxide (ZrO2 nanoparticles were prepared by solution-casting technique. The conductivity was enhanced by addition of dibutyl phthalate (DBP plasticizer and ZrO2 nanofiller with maximum conductivity (1.38×10-4 Scm-1. The absorption edge and band gap values showed decreases upon addition of LiSO3CF3, DBP, and ZrO2 due to the formation of localized states in the SPE and the degree of disorder in the films increased.

  19. A supramolecular gel electrolyte formed from amide based co-gelator for quasi-solid-state dye-sensitized solar cell with boosted electron kinetic processes

    Science.gov (United States)

    Huo, Zhipeng; Wang, Lu; Tao, Li; Ding, Yong; Yi, Jinxin; Alsaedi, Ahmed; Hayat, Tasawar; Dai, Songyuan

    2017-08-01

    A supramolecular gel electrolyte (Tgel > 100 °C) is formed from N,N‧-1,8-octanediylbis-dodecanamide and iodoacetamide as two-component co-gelator, and introduced into the quasi-solid-state dye-sensitized solar cells (QS-DSSCs). The different morphologies of microscopic network between two-component and single-component gel electrolytes have influence on the diffusion of redox couple in gel electrolytes and further affect the electron kinetic processes in QS-DSSCs. Compared with the single-component gel electrolyte, the two-component gel electrolyte has less compact gel network and weaker steric hindrance effect, which provides more effective charge transport channel for the diffusion of I3/I- redox couple. Meanwhile, the sbnd NH2 groups of iodoacetamide molecules interact with Li+ and I3-, which also accelerate the transport of I3-/I- and decrease in the I3- concentration in the TiO2/electrolyte interface. As a result, nearly a 12% improvement in short-circuit photocurrent density (Jsc) and much higher open circuit potential (Voc) are found in the two-component gel electrolyte based QS-DSSC. Consequently, the QS-DSSC based on the supramolecular gel electrolyte obtains a 17% enhancement in the photoelectric conversion efficiency (7.32%) in comparison with the QS-DSSC based on the single-component gel electrolyte (6.24%). Furthermore, the degradations of these QS-DSSCs are negligible after one sun light soaking with UV cutoff filter at 50 °C for 1000 h.

  20. Quasi-solid state polymer electrolytes for dye-sensitized solar cells. Effect of the electrolyte components variation on the triiodide ion diffusion properties and charge-transfer resistance at platinum electrode

    Energy Technology Data Exchange (ETDEWEB)

    Nazmutdinova, G.; Sensfuss, S.; Schroedner, M. [Thuringian Institute for Textile and Plastics Research, Breitscheidstrasse 97, 07407 Rudolstadt (Germany); Hinsch, A. [Fraunhofer Institute for Solar Energy Systems, Heidenhofstrasse 2, 79110 Freiburg (Germany); Sastrawan, R. [Freiburg Materials Research Center FMF, Stefan-Meier-Street 21, 79104 Freiburg (Germany); Gerhard, D.; Himmler, S.; Wasserscheid, P. [Friedrich-Alexander-University, Egerlandstrasse 3, 91058 Erlangen (Germany)

    2006-11-30

    Quasi-solid state polymer electrolytes have been prepared from poly(vinylidenefluoride-co-hexafluoropropylene) (PVDF-HFP) as gelator for 1-ethyl-3-methylimidazolium based ionic liquids (with anions like trifluoromethanesulfonate [EMIM][TfO], bis(trifluoromethanesulfonyl)imide [EMIM][Tf{sub 2}N]) and polyacrylonitrile (PAN) for gelation of 1-ethyl-3-methylimidazolium dicyanamide [EMIM][DCA] as well as I{sup -}/I{sub 3}{sup -} as the redox couple. All electrolytes exhibit high ionic conductivity in the range of 10{sup -3} S/cm. The effect of gelation, redox couple concentration, I{sup -}/I{sub 3}{sup -} ratio, choice of cations and additives on the triiodide diffusion and charge-transfer resistance of the platinum/electrolyte interface (R{sub ct}) were studied. The apparent diffusion coefficient of triiodide ion (D(I{sub 3}{sup -})) at various iodide/triiodide ratios in liquid and gelified electrolytes has been calculated from measurements of the diffusion limited current (I{sub lim}) in electrochemical cell resembling the set-up of a dye-sensitized solar cell. The charge-transfer resistance of the platinum/electrolyte interface as well as the capacitance of the electrical double layer (C{sub dl}) have been calculated from impedance measurements. Electrolytes with reduced content of polymer (2.5 wt.%) were doped with Al{sub 2}O{sub 3} particles of different sizes (50 nm, 300 nm, 1 {mu}m). The dispersion of the particles proceeds by speedy stirring of the hot electrolyte and the addition of PAN provides a homogeneous suspension. The addition of Al{sub 2}O{sub 3} particles causes a slight increase of the triiodide diffusion constants. Furthermore the suggested enhancement of the charge transfer rate shows a dependence on the size of the particles. (author)

  1. Estimation of current constriction losses via 3D tomography reconstructions in electrochemical devices: a case study of a solid oxide cell electrode/electrolyte interface

    DEFF Research Database (Denmark)

    Nielsen, Jimmi; Jørgensen, Peter Stanley

    2017-01-01

    In the present study, the methodology for accurate estimations of the current constriction resistance in solid state electrochemical devices via 3D tomography reconstructions is developed. The methodology is used to determine the current constriction resistances at the Ni:YSZ anode/YSZ electrolyte...

  2. Y-doped BaZrO3 as a chemically stable electrolyte for proton-conducting solid oxide electrolysis cells (SOECs)

    KAUST Repository

    Bi, Lei

    2015-01-01

    A proton-conducting solid oxide electrolysis cell using an Y-doped BaZrO3 electrolyte film, which has been demonstrated to be chemically stable, was successfully fabricated for the first time and showed a promising electrolysis performance.

  3. Energetics of perovskite-type materials applied in solid oxide fuel cells (SOFCs): Electrolytes, cathodes and interconnects

    Science.gov (United States)

    Cheng, Jihong

    Perovskite-type oxides (ABO3) find a great variety of applications in solid oxide fuel cells (SOFCs), including solid electrolytes, cathodes and interconnects, which are closely related to the defect chemistry involved. Thermodynamic studies are needed to systematically understand the nature of the structure-property relations and provide guidance to predict and/or select proper materials. High temperature solution calorimetry in molten oxide solvents is a powerful tool and has been applied for several perovskite systems that have simple (undoped) and complex (doped) compositions. LaBO3 perovskites (B = Al, Ga, Sc, In, Cr, Fe, Co, Ni) represent a group of excellent parent materials for electrolytes, cathodes, and interconnects in SOFCs. Their enthalpies of formation from oxides generally exhibit a relationship between stability and the major structural parameter for perovskites, the tolerance factor. As the tolerance factor deviates more from unity, the enthalpy of formation from oxides becomes less exothermic. This work verifies this general trend for A3+B3+O3 type perovskites, joining other two types, i.e., A1+B5+O 3 and A2+B4+O3. In alkaline earth doped perovskites, though structural parameters are likely to continue affecting stability, defects, which are introduced upon doping, actually play a more profound role in defining energetic trends. In the newly developed electrolyte materials, Mg, Sr, and Ba-doped LaGaO 3 perovskites, oxygen vacancies are created to compensate the charge imbalance between dopant and host ions. Oxygen vacancies have a destabilization effect on the structure due to the partial disconnection of the corner-shared BO6 octahedral framework. On the other hand, they tend to order at the short-range scale, forming vacancy-dopant clusters, as evidenced by neutron diffraction. In alkaline earth doped perovskites that contain transition metals, two charge compensation scenarios are possible: oxidation of the transition metal or creation of

  4. Chemical compatibility study of melilite-type gallate solid electrolyte with different cathode materials

    Energy Technology Data Exchange (ETDEWEB)

    Mancini, Alessandro [INSTM R.U. and Department of Chemistry–Physical Chemistry Division, University of Pavia, Pavia I-27100 (Italy); Felice, Valeria; Natali Sora, Isabella [INSTM R.U. and Department of Engineering, University of Bergamo, Dalmine, Bergamo I-24044 (Italy); Malavasi, Lorenzo [INSTM R.U. and Department of Chemistry–Physical Chemistry Division, University of Pavia, Pavia I-27100 (Italy); Tealdi, Cristina, E-mail: cristina.tealdi@unipv.it [INSTM R.U. and Department of Chemistry–Physical Chemistry Division, University of Pavia, Pavia I-27100 (Italy)

    2014-05-01

    Chemical reactivity between cathodes and electrolytes is a crucial issue for long term SOFCs stability and performances. In this study, chemical reactivity between selected cathodic materials and the ionic conducting melilite La{sub 1.50}Sr{sub 0.50}Ga{sub 3}O{sub 7.25} has been extensively investigated by X-ray powder diffraction in a wide temperature range (up to 1573 K). Perovskite-type La{sub 0.8}Sr{sub 0.2}MnO{sub 3−d} and La{sub 0.8}Sr{sub 0.2}Fe{sub 0.8}Cu{sub 0.2}O{sub 3−d} and K{sub 2}NiF{sub 4}-type La{sub 2}NiO{sub 4+d} were selected as cathode materials. The results of this study allow identifying the most suitable electrode material to be used in combination with the melilite-type gallate electrolyte and set the basis for future work on this novel system. - Graphical abstract: Chemical reactivity between cathodes and electrolytes is a crucial issue for long term SOFCs stability and performances. In this study, chemical reactivity between selected cathodic materials and the ionic conducting melilite La{sub 1.50}Sr{sub 0.50}Ga{sub 3}O{sub 7.25} has been extensively investigated by means of X-ray powder diffraction. - Highlights: • Chemical compatibility between melilite-type gallate and cathodes for SOFCs up to 1573 K. • No reactivity observed between La{sub 0.8}Sr{sub 0.2}Fe{sub 0.8}Cu{sub 0.2}O{sub 3−d} and La{sub 1.50}Sr{sub 0.50}Ga{sub 3}O{sub 7.25}. • Reactivity observed between La{sub 0.80}Sr{sub 0.20}MnO{sub 3−d} and La{sub 1.50}Sr{sub 0.50}Ga{sub 3}O{sub 7.25}. • Significant reactivity observed between La{sub 2}NiO{sub 4+d} and La{sub 1.50}Sr{sub 0.50}Ga{sub 3}O{sub 7.25}.

  5. Mixed solid device based on conducting polymer composite and polymer electrolyte

    Directory of Open Access Journals (Sweden)

    Neves Silmara

    2004-01-01

    Full Text Available Tetraethyl orthosilicate (TEOS derived sol-gel porous films have been utilized as template for the electrochemical polymerization of aniline. Polyaniline-silica composites were obtained and the redox behavior and charge/discharge capacities of a lithium polymeric battery using poly (dimethylsiloxane- co-ethylene oxide as gel polymeric electrolyte, were investigated. The composite presented a high initial capacity (140 mA h g-1 and a reversible capacity of 75 mA h g-1 after 100 charge/discharge cycles. The decrease in the specific capacity was attributed to an increase in charge transfer resistance and a decrease in the diffusion coefficient measured by electrochemical impedance spectroscopy.

  6. Boron cross-linked graphene oxide/polyvinyl alcohol nanocomposite gel electrolyte for flexible solid-state electric double layer capacitor with high performance

    KAUST Repository

    Huang, Yi-Fu

    2014-06-01

    A new family of boron cross-linked graphene oxide/polyvinyl alcohol (GO-B-PVA) nanocomposite gels is prepared by freeze-thaw/boron cross-linking method. Then the gel electrolytes saturated with KOH solution are assembled into electric double layer capacitors (EDLCs). Structure, thermal and mechanical properties of GO-B-PVA are explored. The electrochemical properties of EDLCs using GO-B-PVA/KOH are investigated, and compared with those using GO-PVA/KOH gel or KOH solution electrolyte. FTIR shows that boron cross-links are introduced into GO-PVA, while the boronic structure inserted into agglomerated GO sheets is demonstrated by DMA analysis. The synergy effect of the GO and the boron crosslinking benefits for ionic conductivity due to unblocking ion channels, and for improvement of thermal stability and mechanical properties of the electrolytes. Higher specific capacitance and better cycle stability of EDLCs are obtained by using the GO-B-PVA/KOH electrolyte, especially the one at higher GO content. The nanocomposite gel electrolytes with excellent electrochemical properties and solid-like character are candidates for the industrial application in high-performance flexible solid-state EDLCs. © 2014 Elsevier Ltd.

  7. Structural, morphological, and electrical properties of doped ceria as a solid electrolyte for intermediate-temperature solid oxide fuel cells

    KAUST Repository

    Stojmenović, M.

    2015-03-11

    The solid solutions of CeO2 with one or more rare-earth oxides among Yb2O3, Sm2O3, and Gd2O3 are synthesized by either modified glycine nitrate procedure (MGNP) or self-propagating reaction at room temperature (SPRT). The overall mole fraction of rare-earth oxide dopants was x = 0.2. The characterization was committed by XRPD, TEM, BET, and Raman Spectroscopy methods. According to XRPD and Raman spectroscopy, the obtained products presented the single-phase solid solutions with basic fluorite-type CeO2 structure, regardless on the number and the concentration of dopants. Both XRPD and TEM analysis evidenced the nanometer particle dimensions. The defect model was applied to calculate lattice parameters of single-, co-, and multi-doped solids. The sintering of the sample nanopowders was performed at 1550 °C, in air atmosphere. The sintered samples were characterized by XRPD, SEM, and complex impedance methods. The sintering did not affect the concentration ratios of the constituents. The highest conductivity at 700 °C amounting to 2.14 × 10−2 and 1.92 × 10−2 Ω−1 cm−1 was measured for the sample Ce0.8Sm0.08Gd0.12O2−δ, synthesized by SPRT and MGNP methods, respectively. The corresponding activation energies of conductivity, measured in the temperature range 500–700 °C, amounted to 0.24 and 0.23 eV.

  8. Suppression of Lithium Dendrite Formation by Using LAGP-PEO (LiTFSI) Composite Solid Electrolyte and Lithium Metal Anode Modified by PEO (LiTFSI) in All-Solid-State Lithium Batteries.

    Science.gov (United States)

    Wang, Chunhua; Yang, Yifu; Liu, Xingjiang; Zhong, Hai; Xu, Han; Xu, Zhibin; Shao, Huixia; Ding, Fei

    2017-04-19

    The formation of lithium dendrites is suppressed using a Li1.5Al0.5Ge1.5(PO4)3-poly(ethylene oxide) (LAGP-PEO) composite solid electrolyte and a PEO (lithium bis(trifluoromethane)sulfonimide) [PEO (LiTFSI)]-modified lithium metal anode in all-solid-state lithium batteries. The effects on the anode performance based on the PEO content in the composite solid electrolyte and the molecular weight of PEO used to modify the Li anode are studied. The structure, surface morphology, and stability of the composite solid electrolyte are examined by X-ray diffraction spectroscopy, scanning electron microscopy, and electrochemical tests. Results show that the presence of a PEO-500000(LiTFSI) film on a Li anode results in good mechanical properties and satisfactory interface contact features. The film can also prevent Li from reacting with LAGP. Furthermore, the formation of lithium dendrites can be effectively inhibited as the composite solid electrolyte is combined with the PEO film on the Li anode. The ratio of PEO in the composite solid electrolyte can be reduced to a low level of 1 wt %. PEO remains stable even at a high potential of 5.12 V (vs Li/Li(+)). The assembled Li-PEO (LiTFSI)/LAGP-PEO/LiMn0.8Fe0.2PO4 all-solid-state cell can deliver an initial discharge capacity of 160.8 mAh g(-1) and exhibit good cycling stability and rate performance at 50 °C.

  9. Equilibrium composition of interphase boundaries

    Energy Technology Data Exchange (ETDEWEB)

    Wynblatt, P.

    1990-01-01

    Two modeling approaches have been used to investigate segregation effects at interphase boundaries. The first approach is based on the nearest neighbor bond model, used in conjunction with the regular solution approximation, and is an extension of an earlier framework developed to address segregation phenomena at free surfaces. In order to model a semicoherent interphase boundary, we have employed a second modeling approach, based on Monte Carol simulation, in conjunction with the embedded atom method (EAM). The EAM is a powerful new method for describing interatomic interactions in metallic systems. It includes certain many-body interactions that depend on the local environment of an atom. The Monte Carol approach has been applied to semicoherent interphase boundaries in Cu-Ag-Au alloys dilute in Au. These alloys consist of coexisting Cu-rich and Ag-rich phases, which differ in lattice constant by about 12%, such that good matching across in interface occurs when nine structural units of the Cu-rich phase are opposed to eight structural units of the Ag-rich phase. Thus far, interfaces with two different orientations have been studied: {l brace}001{r brace}-Cu//{l brace}001{r brace}-Ag, {l angle}110{r angle}-Cu//{l angle}110{r angle}-Ag; and {l brace}111{r brace}-Cu//{l brace}111{r brace}-Ag, {l angle}110{r angle}-Cu//{l angle}110{r angle}-Ag. These two interfaces will be referred to as the (001) and (111) interphase boundaries, for short. 18 refs.

  10. Effect of Molecular Weight on Mechanical and Electrochemical Performance of All Solid-State Polymer Electrolyte Membranes

    Science.gov (United States)

    He, Ruixuan; Ward, Daniel; Echeverri, Mauricio; Kyu, Thein

    2015-03-01

    Guided by ternary phase diagrams of polyethylene glycol diacrylate (PEGDA), succinonitrile plasticizer, and LiTFSI salt, completely amorphous solid-state transparent polymer electrolyte membranes (ss-PEM) were fabricated by UV irradiation in the isotropic melt state. Effects of PEGDA molecular weight (700 vs 6000 g/mol) on ss-PEM performance were investigated. These amorphous PEMs have superionic room temperature ionic conductivity of ~10-3 S/cm, whereby PEGDA6000-PEM outperforms its PEGDA700 counterpart, which may be ascribed to lower crosslinking density and greater segmental mobility. The longer chain between crosslinked points of PEGDA6000-PEM is responsible for greater extensibility of ~80% versus ~7% of PEGDA700-PEM. Besides, both PEMs exhibited thermal stability up to 120 °C and electrochemical stability versus Li+/Li up to 4.7V. LiFePO4/PEM/Li and Li4Ti5O12 /PEM/Li half-cells exhibited stable cyclic behavior up to 50 cycles tested with a capacity of ~140mAh/g, suggesting that LiFePO4/PEM/Li4Ti5O12 may be a promising full-cell for all solid-state lithium battery. We thank NSF-DMR 1161070 for providing funding of this project.

  11. Coatable Li4 SnS4 Solid Electrolytes Prepared from Aqueous Solutions for All-Solid-State Lithium-Ion Batteries.

    Science.gov (United States)

    Choi, Young Eun; Park, Kern Ho; Kim, Dong Hyeon; Oh, Dae Yang; Kwak, Hi Ram; Lee, Young-Gi; Jung, Yoon Seok

    2017-06-22

    Bulk-type all-solid-state lithium-ion batteries (ASLBs) for large-scale energy-storage applications have emerged as a promising alternative to conventional lithium-ion batteries (LIBs) owing to their superior safety. However, the electrochemical performance of bulk-type ASLBs is critically limited by the low ionic conductivity of solid electrolytes (SEs) and poor ionic contact between the active materials and SEs. Herein, highly conductive (0.14 mS cm-1 ) and dry-air-stable SEs (Li4 SnS4 ) are reported, which are prepared using a scalable aqueous-solution process. An active material (LiCoO2 ) coated by solidified Li4 SnS4 from aqueous solutions results in a significant improvement in the electrochemical performance of ASLBs. Side-effects of the exposure of LiCoO2 to aqueous solutions are minimized by using predissolved Li4 SnS4 solution. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  12. Preparation of hydroxide ion conductive KOH–layered double hydroxide electrolytes for an all-solid-state iron–air secondary battery

    Directory of Open Access Journals (Sweden)

    Taku Tsuneishi

    2014-06-01

    Full Text Available Anion conductive solid electrolytes based on Mg–Al layered double hydroxide (LDH were prepared for application in an all-solid-state Fe–air battery. The ionic conductivity and the conducting ion species were evaluated from impedance and electromotive force measurements. The ion conductivity of LDH was markedly enhanced upon addition of KOH. The electromotive force in a water vapor concentration cell was similar to that of an anion-conducting polymer membrane. The KOH–LDH obtained was used as a hydroxide ion conductive electrolyte for all-solid-state Fe–air batteries. The cell performance of the Fe–air batteries was examined using a mixture of KOH–LDH and iron-oxide-supported carbon as the negative electrode.

  13. Dendrite Suppression by Synergistic Combination of Solid Polymer Electrolyte Crosslinked with Natural Terpenes and Lithium-Powder Anode for Lithium-Metal Batteries.

    Science.gov (United States)

    Shim, Jimin; Lee, Jae Won; Bae, Ki Yoon; Kim, Hee Joong; Yoon, Woo Young; Lee, Jong-Chan

    2017-05-22

    Lithium-metal anode has fundamental problems concerning formation and growth of lithium dendrites, which prevents practical applications of next generation of high-capacity lithium-metal batteries. The synergistic combination of solid polymer electrolyte (SPE) crosslinked with naturally occurring terpenes and lithium-powder anode is promising solution to resolve the dendrite issues by substituting conventional liquid electrolyte/separator and lithium-foil anode system. A series of SPEs based on polysiloxane crosslinked with natural terpenes are prepared by facile thiol-ene click reaction under mild condition and the structural effect of terpene crosslinkers on electrochemical properties is studied. Lithium powder with large surface area is prepared by droplet emulsion technique (DET) and used as anode material. The effect of the physical state of electrolyte (solid/liquid) and morphology of lithium-metal anode (powder/foil) on dendrite growth behavior is systematically studied. The synergistic combination of SPE and lithium-powder anode suggests an effective solution to suppress the dendrite growth owing to the formation of a stable solid-electrolyte interface (SEI) layer and delocalized current density. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. Pile a combustible a electrolyte polymere solide a consommation directe de gaz propane

    Science.gov (United States)

    Rodriguez Varela, Francisco Javier

    A Polymer Electrolyte Membrane Fuel Cell working with propane as the fuel has been studied. The propane was directly introduced into the cell without previous external reforming, resulting in a Direct Propane Fuel Cell (DPFC). Electrodes of composition 40% Pt/C and 40% PtRu/C (commercial), 20% PtOx/C and 20% Pt/C + 10% CrO3 (home-prepared) have been tested as anodes catalysts in the DPFC. Commercial NafionRTM 117 membranes were used as polymer electrolytes. The anode electrocatalysts were also tested in a H2/O2 fuel cell in order to asses their electrocatalytical characteristics. It has been shown by the polarization curves that the anodes based on 40% Pt/C and 40% PtRu/C provide higher current densities from the H2 /O2 fuel cell than the anodes 20% PtOx/C and 20% Pt/C + 10% CrO3. However, a more in-depth analysis has revealed important features of both home-prepared anodes. For example, relatively high current densities were obtained from these electrocatalysts during the oxidation of H2. Also, the lower open circuit anode potential for the oxidation of H2 has been obtained with the anode 20% PtOx/C. On the other hand, the current density at high cell potentials (970 mV) of the fuel cell based on the anode 20% Pt/C + 10% CrO3 was higher than the current densities of 40% Pt/C and 40% PtRu/C. Kinetic data has shown that the catalyst 20% Pt/C + 10% CrO3 provided a more important exchange current density than the rest of the anode catalysts. It has also been shown that 20% Pt/C + 10% CrO3 possess the largest mass activity while the lower mass activity is that of the catalyst 40% Pt/C. These results have revealed that the home-prepared anodes based on 20% PtOx/C and 20% Pt/C + 10% CrO 3 have important electrocatalytic characteristics for PEM fuel cells applications. Samples of the electrocatalysts were analysed by X-ray diffraction and transmission electron microscopy. A polycrystalline structure has been shown for all Pt-based materials except for 20% PtOx/C which

  15. Bilayer electrolyte-anode for solid oxide fuel cell; Obtencao de bicamadas eletrolito-anodo para pilhas a combustivel de oxido solido

    Energy Technology Data Exchange (ETDEWEB)

    Crochemore, G.B.; Marcomini, R.F.; Souza, D.P.F. de [Universidade Federal de Sao Carlos (GEMM/UFSCAR), Sao Carlos, SP (Brazil). Programa de Pos Graduacao em Ciencia e Engenharia de Materiais], Email: dulcina@ufscar.br; Rabelo, A.A. [Universidade Federal do Para (UFPA), Belem, PA (Brazil). Fac. de Engenharia de Materiais

    2010-07-01

    Solid oxide fuel cell is a high efficient device hence it plays a very important role in the hydrogen economy. However, the cell operation temperature must be lower than 800 deg C, what is attainable for thin Yttria stabilized zirconia (YSZ) electrolytes. The tape casting process is the most used technique because it allows a very fine tuning of the tape thickness. In this work it were investigated the processing conditions for obtaining electrolyte-anode (YSZ/ YSZ-NiO) bilayers with no lamination after the sintering process. (author)

  16. Structure and Dynamics of Polymer-Ceramic Interface in Li1.5Al0.5Ge1.5P3O12/Polyether Solid Electrolyte:A Solid-State NMR Study

    Directory of Open Access Journals (Sweden)

    JIANG Ting-ting

    2017-12-01

    Full Text Available All solid state lithium-ion batteries have the advantages of high safety, long cycle life and high energy density, as compared with the conventional lithium-ion batteries, and have been attracting more and more research interest. Solid electrolyte is a crucial component of all solid state lithium-ion batteries, which largely determine the performance of the batteries. In this work, a polymer-lithium-ceramics complex was designed and synthesized. The structure and dynamics of the polymer-ceramic interface was studied with solid-state NMR techniques.

  17. Beyond the continuum: how molecular solvent structure affects electrostatics and hydrodynamics at solid-electrolyte interfaces.

    Science.gov (United States)

    Bonthuis, Douwe Jan; Netz, Roland R

    2013-10-03

    Standard continuum theory fails to predict several key experimental results of electrostatic and electrokinetic measurements at aqueous electrolyte interfaces. In order to extend the continuum theory to include the effects of molecular solvent structure, we generalize the equations for electrokinetic transport to incorporate a space dependent dielectric profile, viscosity profile, and non-electrostatic interaction potential. All necessary profiles are extracted from atomistic molecular dynamics (MD) simulations. We show that the MD results for the ion-specific distribution of counterions at charged hydrophilic and hydrophobic interfaces are accurately reproduced using the dielectric profile of pure water and a non-electrostatic repulsion in an extended Poisson-Boltzmann equation. The distributions of Na(+) at both surface types and Cl(-) at hydrophilic surfaces can be modeled using linear dielectric response theory, whereas for Cl(-) at hydrophobic surfaces it is necessary to apply nonlinear response theory. The extended Poisson-Boltzmann equation reproduces the experimental values of the double-layer capacitance for many different carbon-based surfaces. In conjunction with a generalized hydrodynamic theory that accounts for a space dependent viscosity, the model captures the experimentally observed saturation of the electrokinetic mobility as a function of the bare surface charge density and the so-called anomalous double-layer conductivity. The two-scale approach employed here-MD simulations and continuum theory-constitutes a successful modeling scheme, providing basic insight into the molecular origins of the static and kinetic properties of charged surfaces, and allowing quantitative modeling at low computational cost.

  18. Magnesium Ethylenediamine Borohydride as Solid-State Electrolyte for Magnesium Batteries

    Science.gov (United States)

    Roedern, Elsa; Kühnel, Ruben-Simon; Remhof, Arndt; Battaglia, Corsin

    2017-04-01

    Solid-state magnesium ion conductors with exceptionally high ionic conductivity at low temperatures, 5 × 10-8 Scm-1 at 30 °C and 6 × 10-5 Scm-1 at 70 °C, are prepared by mechanochemical reaction of magnesium borohydride and ethylenediamine. The coordination complexes are crystalline, support cycling in a potential window of 1.2 V, and allow magnesium plating/stripping. While the electrochemical stability, limited by the ethylenediamine ligand, must be improved to reach competitive energy densities, our results demonstrate that partially chelated Mg2+ complexes represent a promising platform for the development of an all-solid-state magnesium battery.

  19. Construction of All-Solid-State Batteries based on a Sulfur-Graphene Composite and Li9.54 Si1.74 P1.44 S11.7 Cl0.3 Solid Electrolyte.

    Science.gov (United States)

    Xu, Ruochen; Wu, Zhang; Zhang, Shenzhao; Wang, Xiuli; Xia, Yan; Xia, Xinhui; Huang, Xiaohua; Tu, Jiangping

    2017-10-09

    Herein an effective way for construction of all-solid-state lithium-sulfur batteries (LSBs) with sulfur/reduced graphene oxide (rGO) and Li9.54 Si1.74 P1.44 S11.7 Cl0.3 solid electrolyte is reported. In the composite cathode, the Li9.54 Si1.74 P1.44 S11.7 Cl0.3 powder is homogeneously mixed with the S/rGO composite to enhance the ionic conductivity. Coupled with a metallic Li anode and solid electrolyte, the designed S/rGO-Li9.54 Si1.74 P1.44 S11.7 Cl0.3 composite cathode exhibits a high specific capacity and good cycling stability. A high initial discharge capacity of 969 mAh g(-1) is achieved at a current density of 80 mA g(-1) at room temperature and the cell retains a reversible capacity of over 827 mAh g(-1) after 60 cycles. The enhanced performance is attributed to the intimate contact between the S/rGO and Li9.54 Si1.74 P1.44 S11.7 Cl0.3 electrolyte, and high electrical conductivity of rGO and high ionic conductivity of the solid electrolyte. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  20. A chemically stable electrolyte with a novel sandwiched structure for proton-conducting solid oxide fuel cells (SOFCs)

    KAUST Repository

    Bi, Lei

    2013-11-01

    A chemically stable electrolyte structure was developed for proton-conducting SOFCs by using two layers of stable BaZr0.7Pr 0.1Y0.2O3 -δ to sandwich a highly-conductive but unstable BaCe0.8Y0.2O 3 -δ electrolyte layer. The sandwiched electrolyte structure showed good chemical stability in both CO2 and H2O atmosphere, indicating that the BZPY layers effectively protect the inner BCY electrolyte, while the BCY electrolyte alone decomposed completely under the same conditions. Fuel cell prototypes fabricated with the sandwiched electrolyte achieved a relatively high performance of 185 mW cm- 2 at 700 C, with a high electrolyte film conductivity of 4 × 10- 3 S cm- 1 at 600 C. © 2013 Elsevier B.V.

  1. Steam Electrolysis by Proton-Conducting Solid Oxide Electrolysis Cells (SOECs) with Chemically Stable BaZrO3-Based Electrolytes

    KAUST Repository

    Bi, Lei

    2015-07-17

    BaZrO3-based material was applied as the electrolyte for proton-conducting solid oxide fuel cells (SOECs). Compared with the instability of BaCeO3-based proton-conductors, BaZrO3-based material could be a more promising candidate for proton-conducting SOECs due to its excellent chemical stability under H2O conditions, but few reports on this aspect has been made due to the processing difficulty for BaZrO3. Our recent pioneering work has demonstrated the feasibility of using BaZrO3-based electrolyte for SOECs and the fabricated cell achieves relatively high cell performance, which is comparable or even higher than that for BaCeO3-based SOECs and offers better chemical stability. Cell performance can be further improved by tailoring the electrolyte and electrode. © The Electrochemical Society.

  2. FY 1999 Report on research and development of power generation by solid electrolyte fuel cell. Research and development of solid electrolyte fuel cell; 1999 nendo nenryo denchi hatsuden gijutsu kaihatsu kotai denkaishitsugata nenryo denchi no kenkyu kaihatsu kenkyu seika

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-06-01

    This project is aimed at establishment of the module basic technology and commercialization of the solid electrolyte fuel cell in the early stage by designing, construction, operation and performance evaluation of a several kW-class module which incorporates the cylindrical cell fabricated by the wet process. The FY 1999 R and D efforts include (1) cell performance demonstration study: the cylindrical single cell fabricated by the wet process is demonstration-tested to determine the initial performance and durability for continuous operation, thereby comparing the external reforming with internal reforming in output, with the internal reforming rate as the parameter, (2) development of a several kW-class module: the adequate cell arrangement structure within the module is studied by the computer-aided simulation, and the tests for confirming thermal cycle durability of the modified bundle are conducted using the module power generation unit and the several kW-class module is tested, and (3) development of the technology for designing a thermally supported module: the effects of, e.g., air and fuel supply conditions on the module performance are analyzed using the analytical model as the base. Expansion of the module level to the process simulation model has been completed, based on these results. (NEDO)

  3. Materials space of solid-state electrolytes: unraveling chemical composition-structure-ionic conductivity relationships in garnet-type metal oxides using cheminformatics virtual screening approaches.

    Science.gov (United States)

    Kireeva, Natalia; Pervov, Vladislav S

    2017-08-09

    The organic electrolytes of most current commercial rechargeable Li-ion batteries (LiBs) are flammable, toxic, and have limited electrochemical energy windows. All-solid-state battery technology promises improved safety, cycling performance, electrochemical stability, and possibility of device miniaturization and enables a number of breakthrough technologies towards the development of new high power and energy density microbatteries for electronics with low processing cost, solid oxide fuel cells, electrochromic devices, etc. Currently, rational materials design is attracting significant attention, which has resulted in a strong demand for methodologies that can accelerate the design of materials with tailored properties; cheminformatics can be considered as an efficient tool in this respect. This study was focused on several aspects: (i) identification of the parameters responsible for high Li-ion conductivity in garnet structured oxides; (ii) development of quantitative models to elucidate composition-structure-Li ionic conductivity relationships, taking into account the experimental details of sample preparation; (iii) circumscription of the materials space of solid garnet-type electrolytes, which is attractive for virtual screening. Several candidate compounds have been recommended for synthesis as potential solid state electrolyte materials.

  4. Surface oxygen exchange properties of bismuth oxide-based solid electrolytes and electrode materials

    NARCIS (Netherlands)

    Boukamp, Bernard A.; Vinke, I.C.; de Vries, K.J.; Burggraaf, A.J.

    1989-01-01

    The surface oxygen exchange coefficient, ks, has been measured for the solid solution (Bi2O3)0.75(Er2O3)0.25 and (Bi2O3)0.6(Tb2O3)0.4 (abbreviated BE25 and BT40), using gas-phase 18O exchange techniques. The activation enth alpy of ks amounts to ΔE=110 kJ/molforBT40 andΔE=130 kJ/molforBE25. The

  5. A Fluorinated Ether Electrolyte Enabled High Performance Prelithiated Graphite/Sulfur Batteries.

    Science.gov (United States)

    Chen, Shuru; Yu, Zhaoxin; Gordin, Mikhail L; Yi, Ran; Song, Jiangxuan; Wang, Donghai

    2017-03-01

    Lithium/sulfur (Li/S) batteries have attracted great attention as a promising energy storage technology, but so far their practical applications are greatly hindered by issues of polysulfide shuttling and unstable lithium/electrolyte interface. To address these issues, a feasible strategy is to construct a rechargeable prelithiated graphite/sulfur batteries. In this work, a fluorinated ether of bis(2,2,2-trifluoroethyl) ether (BTFE) was reported to blend with 1,3-dioxolane (DOL) for making a multifunctional electrolyte of 1.0 M LiTFSI DOL/BTFE (1:1, v/v) to enable high performance prelithiated graphite/S batteries. First, the electrolyte significantly reduces polysulfide solubility to suppress the deleterious polysulfide shuttling and thus improves capacity retention of sulfur cathodes. Second, thanks to the low viscosity and good wettability, the fluorinated electrolyte dramatically enhances the reaction kinetics and sulfur utilization of high-areal-loading sulfur cathodes. More importantly, this electrolyte forms a stable solid-electrolyte interphase (SEI) layer on graphite surface and thus enables remarkable cyclability of graphite anodes. By coupling prelithiated graphite anodes with sulfur cathodes with high areal capacity of ∼3 mAh cm-2, we demonstrate prelithiated graphite/sulfur batteries that show high sulfur-specific capacity of ∼1000 mAh g-1 and an excellent capacity retention of >65% after 450 cycles at C/10.

  6. A Synopsis of Interfacial Phenomena in Lithium-Based Polymer Electrolyte Electrochemical Cells

    Science.gov (United States)

    Baldwin, Richard S.; Bennett, William R.

    2007-01-01

    The interfacial regions between electrode materials, electrolytes and other cell components play key roles in the overall performance of lithium-based batteries. For cell chemistries employing lithium metal, lithium alloy or carbonaceous materials (i.e., lithium-ion cells) as anode materials, a "solid electrolyte interphase" (SEI) layer forms at the anode/electrolyte interface, and the properties of this "passivating" layer significantly affect the practical cell/battery quality and performance. A thin, ionically-conducting SEI on the electrode surface can beneficially reduce or eliminate undesirable side reactions between the electrode and the electrolyte, which can result in a degradation in cell performance. The properties and phenomena attributable to the interfacial regions existing at both anode and cathode surfaces can be characterized to a large extent by electrochemical impedance spectroscopy (EIS) and related techniques. The intention of the review herewith is to support the future development of lithium-based polymer electrolytes by providing a synopsis of interfacial phenomena that is associated with cell chemistries employing either lithium metal or carbonaceous "composite" electrode structures which are interfaced with polymer electrolytes (i.e., "solvent-free" as well as "plasticized" polymer-binary salt complexes and single ion-conducting polyelectrolytes). Potential approaches to overcoming poor cell performance attributable to interfacial effects are discussed.

  7. Electrodeposited polyethylenedioxythiophene with infiltrated gel electrolyte interface: a close contest of an all-solid-state supercapacitor with its liquid-state counterpart.

    Science.gov (United States)

    Anothumakkool, Bihag; Torris A T, Arun; Bhange, Siddheshwar N; Badiger, Manohar V; Kurungot, Sreekumar

    2014-06-07

    We report the design of an all-solid-state supercapacitor, which has charge storage characteristics closely matching that of its liquid-state counterpart even under extreme temperature and humidity conditions. The prototype is made by electro-depositing polyethylenedioxythiophene (PEDOT) onto the individual carbon fibers of a porous carbon substrate followed by intercalating the matrix with polyvinyl alcohol-sulphuric acid (PVA-H2SO4) gel electrolyte. The electrodeposited layer of PEDOT maintained a flower-like growth pattern along the threads of each carbon fiber. This morphology and the alignment of PEDOT led to an enhanced surface area and electrical conductivity, and the pores in the system enabled effective intercalation of the polymer-gel electrolyte. Thus, the established electrode-electrolyte interface nearly mimics that of its counterpart based on the liquid electrolyte. Consequently, the solid device attained very low internal resistance (1.1 Ω cm(-2)) and a high specific capacitance (181 F g(-1)) for PEDOT at a discharge current density of 0.5 A g(-1). Even with a high areal capacitance of 836 mF cm(-2) and volumetric capacitance of 28 F cm(-3), the solid device retained a mass-specific capacitance of 111 F g(-1) for PEDOT. This is in close agreement with the value displayed by the corresponding liquid-state system (112 F g(-1)), which was fabricated by replacing the gel electrolyte with 0.5 M H2SO4. The device also showed excellent charge-discharge stability for 12 000 cycles at 5 A g(-1). The performance of the device was consistent even under wide-ranging humidity (30-80%) and temperature (-10 to 80 °C) conditions. Finally, a device fabricated by increasing the electrode area four times was used to light an LED, which validated the scalability of the process.

  8. Conductivity Optimization of Tysonite-type La1-xBaxF3-x Solid Electrolytes for Advanced Fluoride Ion Battery.

    Science.gov (United States)

    Bhatia, Harshita; Thieu, Duc Tho; Pohl, Alexander Herald; Chakravadhanula, Venkata Sai K; Fawey, Mohammed H; Kübel, Christian; Fichtner, Maximilian

    2017-07-19

    Use of lithium ion batteries is currently the method of choice when it comes to local stationary storage of electrical energy. In the search for an alternative system, fluoride ion batteries (FIBs) emerge as a candidate due to their high theoretical capacity, and no lithium is needed for its operation. To improve the cycling performance and lower the working temperature of a solid-state battery, one of the critical components is the electrolyte, which needs advanced performance. This paper aims at developing an electrolyte with enhanced ionic conductivity for fluoride ions, to be used in a FIB. Tysonite La1-xBaxF3-x (0 ≤ x ≤ 0.15) solid solutions were synthesized by a facile wet chemical method, and its ionic conductivity was analyzed using electrochemical impedance spectroscopy. A composition study shows that the conductivity reaches a maximum of 1.26 × 10-4 S·cm-1 at 60 °C for the La0.95Ba0.05F2.95 pellet sintered at 800 °C for 20 h, which is 1 order of magnitude higher than that for the as-prepared pellet and 2 times higher than the conductivity of sintered ball-milled batches. The reason for this dramatic increment is the more efficient decrement of grain boundary resistance upon sintering. Morphological, chemical, and structural characterizations of solid electrolytes were studied by X-ray diffraction, scanning electron microscopy , energy dispersive X-ray spectroscopy, physisorption by the Brunauer-Emmett-Teller method, and transmission electron microscopy. Electrochemical testing was carried out for the FIB cell using La0.95Ba0.05F2.95 as electrolyte due to its highest conductivity among the compositions, Ce as anode, and BiF3 as a cathode. The cycling performance was found to be considerably improved when compared to our earlier work, which used the ball-milled electrolyte.

  9. Multifunctional graphene incorporated conducting gel electrolytes in enhancing photovoltaic performances of quasi-solid-state dye-sensitized solar cells

    Science.gov (United States)

    Yuan, Shuangshuang; Tang, Qunwei; He, Benlin; Zhao, Yun

    2014-08-01

    Three-dimensional (3D) gel electrolytes are versatile in elevating encapsulation of liquid electrolyte in dye-sensitized solar cells (DSSCs), however, the poor contact at gel electrolyte/Pt counter electrode interface is unfavorable in electrocatalyzing triiodide ions. In the current work, we report the multifunctions of graphene, graphene oxide, or nanographite incorporated microporous poly(acrylic acid)-cetyltrimethylammonium bromide (PAA-CTAB) conducting gel electrolytes in both sealing liquid electrolyte and conducting refluxed electrons (electrons from external circuit to Pt counter electrode) into 3D framework of the conducting gel electrolyte, aiming at elevating liquid electrolyte content in per unit volume of gel electrolyte, increasing electrocatalytic area toward triiodide ions and diminishing charge-transfer resistance. The electrical and electrochemical performances of the resultant conducting gel electrolytes are thoroughly characterized. Light-to-electric power conversion efficiencies of 7.06%, 6.35%, and 6.17% are determined from DSSCs using graphene, graphene oxide, and nanographite incorporated PAA-CTAB conducting gel electrolytes in comparison with 6.07% from pure PAA-CTAB based DSSC.

  10. Synthesis of Beta-Al2O3 Solid Electrolytes by Glycine-nitrate Combustion

    Directory of Open Access Journals (Sweden)

    ZHU Cheng-fei

    2016-08-01

    Full Text Available Beta-Al2O3 precursor powders were synthesized by glycine-nitrate combustion at a low temperature using metal nitrate and GNP as raw materials. The thermal decomposition mechanism of the gel and the formation process of beta-Al2O3 were investigated by XRD, TG/DSC, SEM, NMR and EIS. The results show that beta-Al2O3 precursor powder with the average size of 42.0nm can be obtained at 1150℃, 150℃ lower than the solid state reaction. The precursor powder has good forming and sintering performance. The sample is calcined at 1620℃, then the Al(Ⅳ and the Al(Ⅵ in the structure of the sample is around δ=45 and δ=-6, respectively. The relative density of the sample is 97.6%. The ionic conductivity at 350℃ is 0.046S·cm-1.

  11. Ternary natural deep eutectic solvent (NADES) infused phthaloyl starch as cost efficient quasi-solid gel polymer electrolyte.

    Science.gov (United States)

    Selvanathan, Vidhya; Azzahari, Ahmad Danial; Abd Halim, Adyani Azizah; Yahya, Rosiyah

    2017-07-01

    A first-of-its-kind, eco-friendly quasi-solid bioelectrolyte derived from potato starch was prepared. Starch was chemically modified via phthaloylation to synthesize amorphous, hydrophobic starch derivative and the attachment of the phthaloyl group was confirmed via FTIR which showed phthalate ester peak at 1715cm(-1); and (1)H NMR peaks between 7.30-7.90ppm attributed to the aromatic protons of the phthaloyl group. The resulting starch derivative was then infused with ternary natural deep eutectic solvent (NADES) made from different molar ratios of choline chloride, urea and glycerol. Electrochemical Impedance Spectroscopy (EIS) revealed that the highest ionic conductivity was obtained by the system consisting of NADES with choline chloride:urea:glycerol in molar ratios of 4:6:2, with a magnitude of 2.86mScm(-1), hence validating the prospects of the materials to be further experimented as an alternative electrolyte in various electrochemical devices. Copyright © 2017 Elsevier Ltd. All rights reserved.

  12. High Conductivity, High Strength Solid Electrolytes Formed by in Situ Encapsulation of Ionic Liquids in Nanofibrillar Methyl Cellulose Networks.

    Science.gov (United States)

    Mantravadi, Ramya; Chinnam, Parameswara Rao; Dikin, Dmitriy A; Wunder, Stephanie L

    2016-06-01

    Strong, solid polymer electrolyte ion gels, with moduli in the MPa range, a capacitance of 2 μF/cm(2), and high ambient ionic conductivities (>1 × 10(-3) S/cm), all at room temperature, have been prepared from butyl-N-methyl pyrrolidinium bis(trifluoromethylsulfonyl) imide (PYR14TFSI) and methyl cellulose (MC). These properties are particularly attractive for supercapacitor applications. The ion gels are prepared by codissolution of PYR14TFSI and MC in N,N-dimethylformamide (DMF), which after heating and subsequent cooling form a gel. Evaporation of DMF leave thin, flexible, self-standing ion gels with up to 97 wt % PYR14TFSI, which have the highest combined moduli and ionic conductivity of ion gels to date, with an excellent electrochemical stability window (5.6 V). These favorable properties are attributed to the immiscibility of PYR14TFSI in MC, which permits the ionic conductivity to be independent of the MC at low MC content, and the in situ formation of a volume spanning network of semicrystalline MC nanofibers, which have a high glass transition temperature (Tg = 190 °C) and remain crystalline until they degrade at 300 °C.

  13. Electrochemical characterization on SDC/Na2CO3 nanocomposite electrolyte for low temperature solid oxide fuel cells.

    Science.gov (United States)

    Gao, Zhan; Raza, Rizwan; Zhu, Bin; Mao, Zongqiang

    2011-06-01

    Our previous work has demonstrated that novel core-shell SDC/Na2CO3 nanocomposite electrolyte possesses great potential for the development of low temperature (300-600 degrees C) solid oxide fuel cells. This work further characterizes the nanocomposite SDC/Na2CO3 electrochemical properties and conduction mechanism. The microstructure of the nanocomposite sintered at different temperatures was analyzed through scanning electron microscope (SEM) and X-ray diffraction (XRD). The electrical and electrochemical properties were studied. Significant conductivity enhancement was observed in the H2 atmosphere compared with that of air atmosphere. The ratiocination of proton conduction rather than electronic conduction has been proposed consequently based on the observation of fuel cell performance. The fuel cell performance with peak power density of 375 mW cm(-2) at 550 degrees C has been achieved. A.C. impedance for the fuel cell under open circuit voltage (OCV) conditions illustrates the electrode polarization process is predominant in rate determination.

  14. Structural and ionic conductivity studies on proton conducting solid biopolymer electrolyte based on 2hydroxyethyl cellulose incorporated DTAB

    Science.gov (United States)

    Ahmad, N. H.; Bakar, N. Y.; Isa, M. I. N.

    2017-09-01

    Solid biopolymer electrolytes (SBEs) based on 2hydroxyethyl cellulose (2HEC) complexes with dodecyltrimethyl ammonium bromide (DTAB) salt in various composition (wt. %) were successfully prepared by using solution casting technique. The ion - polymer interaction and structural studies have been reported by Fourier transform infrared spectroscopy (FTIR) supported with X - ray diffraction (XRD) and Electrical impedance spectroscopy (EIS). FTIR spectral shows interaction of 2HEC with DTAB happen at peak 2914cm-1, 2848cm-1, 2353cm-1, 2328cm-1, 1720cm-1, 1437cm-1, 1344cm-1, 1198cm-1 1095cm-1 1051cm-1, 912cm-1 and 872cm-1. The interaction of complexes leads to an increase in number of ion jump into neighboring vacant sites until it reaches the highest conductivity at room temperature which is 2.80 x 10-5 Scm-1 for sample containing 9wt. % of DTAB. The temperature dependence of the SBEs system exhibits Arrhenius behavior and the XRD spectral analysis shows the higher salt loading the crystallinity of the SBEs which also increased.

  15. Bubble-Sheet-Like Interface Design with an Ultrastable Solid Electrolyte Layer for High-Performance Dual-Ion Batteries.

    Science.gov (United States)

    Qin, Panpan; Wang, Meng; Li, Na; Zhu, Haili; Ding, Xuan; Tang, Yongbing

    2017-05-01

    In this work, a bubble-sheet-like hollow interface design on Al foil anode to improve the cycling stability and rate performance of aluminum anode based dual-ion battery is reported, in which, a carbon-coated hollow aluminum anode is used as both anode materials and current collector. This anode structure can guide the alloying position inside the hollow nanospheres, and also confine the alloy sizes within the hollow nanospheres, resulting in significantly restricted volumetric expansion and ultrastable solid electrolyte interface (SEI). As a result, the battery demonstrates an excellent long-term cycling stability within 1500 cycles with ≈99% capacity retention at 2 C. Moreover, this cell displays an energy density of 169 Wh kg(-1) even at high power density of 2113 W kg(-1) (10 C, charge and discharge within 6 min), which is much higher than most of conventional lithium ion batteries. The interfacial engineering strategy shown in this work to stabilize SEI layer and control the alloy forming position could be generalized to promote the research development of metal anodes based battery systems. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  16. An Approach to Solid-State Electrical Double Layer Capacitors Fabricated with Graphene Oxide-Doped, Ionic Liquid-Based Solid Copolymer Electrolytes

    Directory of Open Access Journals (Sweden)

    N. F. A. Fattah

    2016-06-01

    Full Text Available Solid polymer electrolyte (SPE composed of semi-crystalline poly (vinylidene fluoride-hexafluoropropylene [P(VdF-HFP] copolymer, 1-ethyl-3-methylimidazolium bis (trifluoromethyl sulphonyl imide [EMI-BTI] and graphene oxide (GO was prepared and its performance evaluated. The effects of GO nano-filler were investigated in terms of enhancement in ionic conductivity along with the electrochemical properties of its electrical double layer capacitors (EDLC. The GO-doped SPE shows improvement in ionic conductivity compared to the P(VdF-HFP-[EMI-BTI] SPE system due to the existence of the abundant oxygen-containing functional group in GO that assists in the improvement of the ion mobility in the polymer matrix. The complexation of the materials in the SPE is confirmed in X-ray diffraction (XRD and thermogravimetric analysis (TGA studies. The electrochemical performance of EDLC fabricated with GO-doped SPE is examined using cyclic voltammetry and charge–discharge techniques. The maximum specific capacitance obtained is 29.6 F∙g−1, which is observed at a scan rate of 3 mV/s in 6 wt % GO-doped, SPE-based EDLC. It also has excellent cyclic retention as it is able keep the performance of the EDLC at 94% even after 3000 cycles. These results suggest GO doped SPE plays a significant role in energy storage application.

  17. Analyses of ionic conductivity and dielectric behavior of solid polymer electrolyte based 2-hydroxyethyl cellulose doped ammonium nitrate plasticized with ethylene carbonate

    Science.gov (United States)

    Hafiza, M. N.; Isa, M. I. N.

    2017-09-01

    A solid polymer electrolyte (SPE) based 2-hydroxyethyl cellulose (2-HEC) doped ammonium nitrate (NH4NO3) plasticized with ethylene carbonate (EC) has been investigated using electrical impedance spectroscopy (EIS). The highest ionic conductivity of (1.17±0.01) × 10-3 Scm-1 was obtained for 2-HEC-NH4NO3 plasticized with 16 wt.% EC. Dielectric and modulus study showed non-Debye type of 2-HEC-NH4NO3-EC SPE.

  18. Optimization of Pore Structure of Cathodic Carbon Supports for Solvate Ionic Liquid Electrolytes Based Lithium-Sulfur Batteries.

    Science.gov (United States)

    Zhang, Shiguo; Ikoma, Ai; Li, Zhe; Ueno, Kazuhide; Ma, Xiaofeng; Dokko, Kaoru; Watanabe, Masayoshi

    2016-10-04

    Lithium-sulfur (Li-S) batteries are a promising energy-storage technology owing to their high theoretical capacity and energy density. However, their practical application remains a challenge because of the serve shuttle effect caused by the dissolution of polysulfides in common organic electrolytes. Polysulfide-insoluble electrolytes, such as solvate ionic liquids (ILs), have recently emerged as alternative candidates and shown great potential in suppressing the shuttle effect and improving the cycle stability of Li-S batteries. Redox electrochemical reactions in polysulfide-insoluble electrolytes occur via a solid-state process at the interphase between the electrolyte and the composite cathode; therefore, creating an appropriate interface between sulfur and a carbon support is of great importance. Nevertheless, the porous carbon supports established for conventional organic electrolytes may not be suitable for polysulfide-insoluble electrolytes. In this work, we investigated the effect of the porous structure of carbon materials on the Li-S battery performance in polysulfide-insoluble electrolytes using solvate ILs as a model electrolyte. We determined that the pore volume (rather than the surface area) exerts a major influence on the discharge capacity of S composite cathodes. In particular, inverse opal carbons with three-dimensionally ordered interconnected macropores and a large pore volume deliver the highest discharge capacity. The battery performance in both polysulfide-soluble electrolytes and solvate ILs was used to study the effect of electrolytes. We propose a plausible mechanism to explain the different porous structure requirements in polysulfide-soluble and polysulfide-insoluble electrolytes.

  19. High throughput methodology for synthesis, screening, and optimization of solid state lithium ion electrolytes.

    Science.gov (United States)

    Beal, Mark S; Hayden, Brian E; Le Gall, Thierry; Lee, Christopher E; Lu, Xiaojuan; Mirsaneh, Mehdi; Mormiche, Claire; Pasero, Denis; Smith, Duncan C A; Weld, Andrew; Yada, Chihiro; Yokoishi, Shoji

    2011-07-11

    A study of the lithium ion conductor Li(3x)La(2/3-x)TiO(3) solid solution and the surrounding composition space was carried out using a high throughput physical vapor deposition system. An optimum total ionic conductivity value of 5.45 × 10(-4) S cm(-1) was obtained for the composition Li(0.17)La(0.29)Ti(0.54) (Li(3x)La(2/3-x)TiO(3)x = 0.11). This optimum value was calculated using an artificial neural network model based on the empirical data. Due to the large scale of the data set produced and the complexity of synthesis, informatics tools were required to analyze the data. Partition analysis was carried out to determine the synthetic parameters of importance and their threshold values. Multivariate curve resolution and principal component analysis were applied to the diffraction data set. This analysis enabled the construction of phase distribution diagrams, illustrating both the phases obtained and the compositional zones in which they occur. The synthetic technique presented has significant advantages over other thin film and bulk methodologies, in terms of both the compositional range covered and the nature of the materials produced.

  20. Technical Update: Johnson Space Center system using a solid electrolytic cell in a remote location to measure oxygen fugacities in CO/CO2 controlled-atmosphere furnaces

    Science.gov (United States)

    Jurewicz, A. J. G.; Williams, R. J.; Le, L.; Wagstaff, J.; Lofgren, G.; Lanier, A.; Carter, W.; Roshko, A.

    1993-01-01

    Details are given for the design and application of a (one atmosphere) redox-control system. This system differs from that given in NASA Technical Memorandum 58234 in that it uses a single solid-electrolytic cell in a remote location to measure the oxygen fugacities of multiple CO/CO2 controlled-atmosphere furnaces. This remote measurement extends the range of sample-furnace conditions that can be measured using a solid-electrolytic cell, and cuts costs by extending the life of the sensors and by minimizing the number of sensors in use. The system consists of a reference furnace and an exhaust-gas manifold. The reference furnace is designed according to the redox control system of NASA Technical Memorandum 58234, and any number of CO/CO2 controlled-atmosphere furnaces can be attached to the exhaust-gas manifold. Using the manifold, the exhaust gas from individual CO/CO2 controlled atmosphere furnaces can be diverted through the reference furnace, where a solid-electrolyte cell is used to read the ambient oxygen fugacity. The oxygen fugacity measured in the reference furnace can then be used to calculate the oxygen fugacity in the individual CO/CO2 controlled-atmosphere furnace. A BASIC computer program was developed to expedite this calculation.

  1. A structural study of solid electrolyte interface on negative electrode of lithium-Ion battery by electron microscopy.

    Science.gov (United States)

    Matsushita, Tadashi; Watanabe, Jiro; Nakao, Tatsuya; Yamashita, Seiichi

    2014-11-01

    For the last decades, the performance of the lithium-ion battery (LIB) has been significantly improved and its applications have been expanding rapidly. However, its performance has yet to be enhanced.In the lithium-ion battery development, it is important to elucidate the electrode structure change in detail during the charge and discharge cycling. In particular, solid electrolyte interface (SEI) formed by decomposition of the electrolytes on the graphite negative electrode surface should play an important role for battery properties. Therefore, it is essential to control the structure and composition of SEI to improve the battery performance. Here, we conducted a scanning electron microscope (SEM) and transmission electron microscope (TEM) study to elucidate the structures of the SEI during the charge and discharge process using LiNi1/3Co1/3Mn1/3O2 [1] cathode and graphite anode. [2] Since SEI is a lithium-containing compound with high activity, it was observed without being exposed to the atmosphere. The electrodes including SEI were sampled after dismantling batteries with cutoff voltages of 3V and 4.2V for the charge process and 3V for the discharge process. Fig.1 shows SEM images of the graphite electrode surface during the charge and discharge process. The change of the SEI structure during the process was clearly observed. Further, TEM images showed that the SEI grew thicker during the charge process and becomes thinner when discharged. These results with regard to the reversible SEI structure could give a new insight for the battery development.jmicro;63/suppl_1/i21/DFU056F1F1DFU056F1Fig. 1.SEM images of the graphite electrode surface:(a) before charge process;(b) with charge-cutoff voltage of 3.0V; (c) with charge-cutoff voltage of 4.2V; (d) with discharge-cutoff voltage of 3.0V. © The Author 2014. Published by Oxford University Press on behalf of The Japanese Society of Microscopy. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  2. Determination of a partial electronic conduction parameter of solid electrolytes for an oxygen sensor by using AC two terminals method. Koryu 2 tanshi ho ni yoru sanso sensor yo kotai denkaishitsu no denshi dendo sei parameter no sokutei

    Energy Technology Data Exchange (ETDEWEB)

    Sasabe, M. (Chiba Inst. of Tech., Chiba (Japan)); Miyashita, M. (Toshiba Tungalloy Co. Ltd., Kawasaki (Japan)); Hua, J.Z. (Harbin Inst. of Tech., Harbin (China)); Senoo, H. (Osaka Sanso Kogyo Ltd., Osaka (Japan))

    1991-06-01

    An oxygen sensor with a built-in oxygen concentration cell using solid zirconia electrolyte can measure oxygen activity by immersing it in molten steel for ten and some seconds. For measuring oxygen in molten steel, the value of partial electronic conduction parameter of solid electrolyte is important. So far the swinkels method using the polarization electromotive force has been used for measurement, but it has several problematical points. In this research, in order to solve them, a new measuring method of electroconductive parameters of solid electrolyte by the AC two terminal method was designed and measurement was done on various zirconia based solid electrolytes. It was clarified that this method has the following features: The measured values by this method agree with those by the swinkels method which had so far been the sole measuring method. The sufficient size of the electrolyte for the measurement is 2mm in diameter and 10mm in length or more, and in comparison with the swinkels method, a fairly small specimen can be meamsured. There is no restriction on the shape of electrolyte and this method does not dirty solid electrolyte. Its measuring time is shorter than the swinkels method. 17 refs., 13 figs., 2 tabs.

  3. Fast lithium-ion conducting thin-film electrolytes integrated directly on flexible substrates for high-power solid-state batteries.

    Science.gov (United States)

    Ihlefeld, Jon F; Clem, Paul G; Doyle, Barney L; Kotula, Paul G; Fenton, Kyle R; Apblett, Christopher A

    2011-12-15

    By utilizing an equilibrium processing strategy that enables co-firing of oxides and base metals, a means to integrate the lithium-stable fast lithium-ion conductor lanthanum lithium tantalate directly with a thin copper foil current collector appropriate for a solid-state battery is presented. This resulting thin-film electrolyte possesses a room temperature lithium-ion conductivity of 1.5 × 10(-5) S cm(-1) , which has the potential to increase the power of a solid-state battery over current state of the art. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  4. Electrochemical Reduction of Dissolved Oxygen in Alkaline, Solid Polymer Electrolyte Films.

    Science.gov (United States)

    Novitski, David; Kosakian, Aslan; Weissbach, Thomas; Secanell, Marc; Holdcroft, Steven

    2016-11-30

    Mass transport of oxygen through an ionomer contained within the cathode catalyst layer in an anion exchange membrane fuel cell is critical for a functioning fuel cell, yet is relatively unexplored. Moreover, because water is a reactant in the oxygen reduction reaction (ORR) in alkaline media, an adequate supply of water is required. In this work, ORR mass transport behavior is reported for methylated hexamethyl-p-terphenyl polymethylbenzimidazoles (HMT-PMBI), charge balanced by hydroxide ions (IEC from 2.1 to 2.5 mequiv/g), and commercial Fumatec FAA-3 membranes. Electrochemical mass transport parameters are determined by potential step chronoamperometry using a Pt microdisk solid-state electrochemical cell, in air at 60 °C, with relative humidity controlled between 70% and 98%. The oxygen diffusion coefficient (D bO2 ), oxygen concentration (c bO2 ), and oxygen permeability (D bO2 ·c bO2 ) were obtained by nonlinear curve fitting of the current transients using the Shoup-Szabo equation. Mass transport parameters are correlated to water content of the ionomer membrane. It is found that the oxygen diffusion coefficients decreased by 2 orders of magnitude upon reducing the water content of the ionomer membrane by lowering the relative humidity. The limitation of the Shoup-Szabo equation for extracting ORR mass transport parameters using thin ionomer films was evaluated by numerical modeling of the current transients, which revealed that a significant discrepancy (up to 29% under present conditions) was evident for highly hydrated membranes for which the oxygen diffusion coefficient was largest, and in which the oxygen depletion region reached the ionomer/gas interface during the chronoamperometric analysis.

  5. Polyaniline-grafted silica nanocomposites-based gel electrolytes for quasi-solid-state dye-sensitized solar cells

    Science.gov (United States)

    Ma, Pin; Tan, Jing; Cheng, Hongbo; Fang, Yanyan; Wang, Yanan; Dai, Yuhua; Fang, Shibi; Zhou, Xiaowen; Lin, Yuan

    2018-01-01

    Polyaniline-grafted silica nanocomposites (PANI-SiO2), which are synthesized through in-situ surface chemical oxidative polymerization of aniline with the NH2-modified silica nanoparticles, are exploited as gelators in the ionic-liquid electrolytes for dye-sensitized solar cells (DSCs). It can be clearly seen that the PANI-SiO2 nanocomposites have the well-interconnected network structure, which not only serve as gelators to effectively solidfy the ionic-liquid electrolytes, but also significantly improve the ion conductivity of electrolytes and the diffusion coefficient of I3- ions. As a result, an optimal efficiency of 7.15% for DSC using gel electrolyte is achieved due to the enhancement of photocurrent density (Jsc) and fill factor (FF), which is increased by 18.99% than that of the cell using ionic-liquid electrolyte.

  6. Effective Infiltration of Gel Polymer Electrolyte into Silicon-Coated Vertically Aligned Carbon Nanofibers as Anodes for Solid-State Lithium-Ion Batteries.

    Science.gov (United States)

    Pandey, Gaind P; Klankowski, Steven A; Li, Yonghui; Sun, Xiuzhi Susan; Wu, Judy; Rojeski, Ronald A; Li, Jun

    2015-09-23

    This study demonstrates the full infiltration of gel polymer electrolyte into silicon-coated vertically aligned carbon nanofibers (Si-VACNFs), a high-capacity 3D nanostructured anode, and the electrochemical characterization of its properties as an effective electrolyte/separator for future all-solid-state lithium-ion batteries. Two fabrication methods have been employed to form a stable interface between the gel polymer electrolyte and the Si-VACNF anode. In the first method, the drop-casted gel polymer electrolyte is able to fully infiltrate into the open space between the vertically aligned core-shell nanofibers and encapsulate/stabilize each individual nanofiber in the polymer matrix. The 3D nanostructured Si-VACNF anode shows a very high capacity of 3450 mAh g(-1) at C/10.5 (or 0.36 A g(-1)) rate and 1732 mAh g(-1) at 1C (or 3.8 A g(-1)) rate. In the second method, a preformed gel electrolyte film is sandwiched between an Si-VACNF electrode and a Li foil to form a half-cell. Most of the vertical core-shell nanofibers of the Si-VACNF anode are able to penetrate into the gel polymer film while retaining their structural integrity. The slightly lower capacity of 2800 mAh g(-1) at C/11 rate and ∼1070 mAh g(-1) at C/1.5 (or 2.6 A g(-1)) rate have been obtained, with almost no capacity fade for up to 100 cycles. Electrochemical impedance spectroscopy does not show noticeable changes after 110 cycles, further revealing the stable interface between the gel polymer electrolyte and the Si-VACNFs anode. These results show that the infiltrated flexible gel polymer electrolyte can effectively accommodate the stress/strain of the Si shell due to the large volume expansion/contraction during the charge-discharge processes, which is particularly useful for developing future flexible solid-state lithium-ion batteries incorporating Si-anodes.

  7. Solid oxide reversible cells (SORCs) using LaGaO3-based oxide electrolyte and oxide fuel electrode

    Science.gov (United States)

    Ishihara, Tatsumi

    2017-09-01

    Activity of La0.8Sr0.2FeO3 (LSF) to the fuel electrode reaction in Solid Oxide Reversible Cells (SORCs) was investigated by using La0.9Sr0.1Ga0.8Mg0.2O3 (LSGM) and Ba0.6La0.4CoO3 (BLC) as electrolyte and air electrode, respectively. In electrolysis mode (SOEC), LSF electrode exhibited small overpotential under the atmosphere without H2 co-feeding; the current densities reached -1.42, -0.92, -0.36 A/cm2 at 1.4 V at 900, 800, 700 °C, respectively and H2 formation rate is well agreed with that estimated by Faraday's law. On the other hand, in the SOEC-SOFC reversible mode with the gas composition of 20% steam /20%H2/60%Ar, the maximum power densities of 0.42, 0.28, 0.11 W/cm2 were achieved at 900, 800 and 700 °C, respectively. In addition, the cyclic reversible operation was also investigated at 800 °C, and it was found that the cell showed high stability over 30 cycles. DC polarization measurement suggests that the exchange current density of LSF is 14 mA/cm2 at 700 °C, which is almost the same with that of Ni-YSZ reported. XRD measurement and SEM observation after the reversible measurement suggest that LSF is highly stable under SOEC-SOFC cyclic operation condition. Therefore, LSF is promising as the fuel electrode for SORCs, although the conductivity is not sufficiently high as electrode.

  8. Low molecular mass organogelator based gel electrolyte gelated by a quaternary ammonium halide salt for quasi-solid-state dye-sensitized solar cells

    Science.gov (United States)

    Huo, Zhipeng; Zhang, Changneng; Fang, Xiaqin; Cai, Molang; Dai, Songyuan; Wang, Kongjia

    Quasi-solid-state dye-sensitized solar cells (DSC) are fabricated using tetradodecylammonium bromide as a low molecular mass organogelator (LMOG) to form gel electrolyte with a high solution-to-gel transition temperature (T SG) of 75 °C to hinder flow and volatilization of the liquid. The steady-state voltammograms reveal that the diffusion of the I 3 - and I - in the gel electrolyte is hindered by the self-assembled network of the gel. An increased interfacial exchange current density (j 0) of 4.95 × 10 -8 A cm -2 and a decreased electron recombination lifetime (τ) of 117 ms reveal an increased electron recombination at the dyed TiO 2 photoelectrode/electrolyte interface in the DSC after gelation. The results of the accelerated aging tests show that the gel electrolyte based dye-sensitized solar cell can retain over 93% of its initial photoelectric conversion efficiency value after successive heating at 60 °C for 1000 h, and device degradation is negligible after one sun light soaking with UV cutoff filter for 1000 h.

  9. Low molecular mass organogelator based gel electrolyte gelated by a quaternary ammonium halide salt for quasi-solid-state dye-sensitized solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Huo, Zhipeng; Zhang, Changneng; Fang, Xiaqin; Cai, Molang; Dai, Songyuan; Wang, Kongjia [Key Lab of Novel Thin Film Solar Cells, Chinese Academy of Sciences (China); Institute of Plasma Physics, Chinese Academy of Sciences (China)

    2010-07-01

    Quasi-solid-state dye-sensitized solar cells (DSC) are fabricated using tetradodecylammonium bromide as a low molecular mass organogelator (LMOG) to form gel electrolyte with a high solution-to-gel transition temperature (T{sub SG}) of 75 C to hinder flow and volatilization of the liquid. The steady-state voltammograms reveal that the diffusion of the I{sub 3}{sup -} and I{sup -} in the gel electrolyte is hindered by the self-assembled network of the gel. An increased interfacial exchange current density (j{sub 0}) of 4.95 x 10{sup -8} A cm{sup -2} and a decreased electron recombination lifetime ({tau}) of 117 ms reveal an increased electron recombination at the dyed TiO{sub 2} photoelectrode/electrolyte interface in the DSC after gelation. The results of the accelerated aging tests show that the gel electrolyte based dye-sensitized solar cell can retain over 93% of its initial photoelectric conversion efficiency value after successive heating at 60 C for 1000 h, and device degradation is negligible after one sun light soaking with UV cutoff filter for 1000 h. (author)

  10. Effects of crown ethers in nanocomposite silica-gel electrolytes on the performance of quasi-solid-state dye-sensitized solar cells

    KAUST Repository

    Huang, Kuan-Chieh

    2010-04-01

    The effects of crown ethers (CEs) on the performance of quasi-solid-state dye-sensitized solar cells (DSSCs) have been investigated. Nanocomposite silica was used to form gel matrices in the electrolytes, which contained lithium iodide (LiI) and iodine (I2) in 3-methoxypropionitrile (MPN) solvent. Three types of CEs, 12-crown-4 (12-C-4), 15-crown-5 (15-C-5), and 18-crown-6 (18-C-6) were used as additives to the gel electrolytes. DSSCs containing CEs showed enhancements in solar-to-electricity conversion efficiencies (η), with reference to the one without them. The crown ether, 15-C-5, with a size of cavity matching with the size of Li+ in the electrolyte rendered for its DSSC the best performance with an η of 3.60%, under 100 mW/cm2 illumination, as compared to 2.44% for the cell without any CE. Enhancements in the photovoltaic parameters of the cells with the CEs were explained based on the binding abilities of the CEs with lithium ions (Li+) in the electrolyte. Linear sweep voltammetry (LSV) measurements and electrochemical impedance spectra were used to substantiate the explanations. © 2009 Elsevier B.V. All rights reserved.

  11. Tailoring the electrode-electrolyte interface of Solid Oxide Fuel Cells (SOFC) by laser micro-patterning to improve their electrochemical performance

    Science.gov (United States)

    Cebollero, J. A.; Lahoz, R.; Laguna-Bercero, M. A.; Larrea, A.

    2017-08-01

    Cathode activation polarisation is one of the main contributions to the losses of a Solid Oxide Fuel Cell. To reduce this loss we use a pulsed laser to modify the surface of yttria stabilized zirconia (YSZ) electrolytes to make a corrugated micro-patterning in the mesoscale. The beam of the laser source, 5 ns pulse width and emitting at λ = 532 nm (green region), is computer-controlled to engrave the selected micro-pattern on the electrolyte surface. Several laser scanning procedures and geometries have been tested. Finally, we engrave a square array with 28 μm of lattice parameter and 7 μm in depth on YSZ plates. With these plates we prepare LSM-YSZ/YSZ/LSM-YSZ symmetrical cells (LSM: La1-xSrxMnO3) and determine their activation polarisation by Electrochemical Impedance Spectroscopy (EIS). To get good electrode-electrolyte contact after sintering it is necessary to use pressure-assisted sintering with low loads (about 5 kPa), which do not modify the electrode microstructure. The decrease in polarisation with respect to an unprocessed cell is about 30%. EIS analysis confirms that the reason for this decrease is an improvement in the activation processes at the electrode-electrolyte interface.

  12. based gel polymer electrolytes

    Indian Academy of Sciences (India)

    vity at ambient temperature (Wright 1975; Martuscelli et al 1984). Generally solid polymer electrolytes have many advantages, viz. high ionic conductivity, high specific energy, wide electrochemical stability windows, light and easy processibility. Apart from this, polymer electrolyte studies have been carried out in poly(vinyl ...

  13. High-energy-density, all-solid-state microsupercapacitors with three-dimensional interdigital electrodes of carbon/polymer electrolyte composite

    Science.gov (United States)

    Pu, Juan; Wang, Xiaohong; Zhang, Tianyi; Li, Siwei; Liu, Jinghe; Komvopoulos, Kyriakos

    2016-01-01

    Novel all-solid-state microsupercapacitors (MSCs) with three-dimensional (3D) electrodes consisting of active materials (i.e., graphene or activated carbon (AC) particles) and polymer electrolyte (PE) designed for high-energy-density storage applications were fabricated and tested in this work. The incorporation of PE in the electrode material enhances the accessibility of electrolyte ions to the surface of active materials and decreases the ion diffusion path during electrochemical charge/discharge. For a scan rate of 5 mV s-1, the MSCs with graphene/PE and AC/PE composite electrodes demonstrate a very high areal capacitance of 95 and 134 mF cm-2, respectively, comparable to that of 3D MSCs with liquid electrolyte. In addition, the graphene/PE MSCs show a ˜70% increase in specific capacitance after 10 000 charge/discharge cycles, attributed to an electro-activation process resulting from ion intercalation between the graphene nanosheets. The AC/PE MSCs also demonstrate excellent stability. The results of this study illustrate the potential of the present 3D MSCs for various high-density solid-state energy storage applications.

  14. High performance red phosphorus electrode in ionic liquid-based electrolyte for Na-ion batteries

    Science.gov (United States)

    Dahbi, Mouad; Fukunishi, Mika; Horiba, Tatsuo; Yabuuchi, Naoaki; Yasuno, Satoshi; Komaba, Shinichi

    2017-09-01

    Electrochemical performance of the red phosphorus electrode was examined in ionic-liquid electrolyte, 0.25 mol dm-3 sodium bisfluorosulfonylamide (NaFSA) dissolved N-methyl-N-propylpyridinium-bisfluorosulfonylamide (MPPFSA), at room temperature. We compared its electrochemical performance to conventional EC/PC/DEC, EC/DEC, and PC solutions containing 1 mol dm-3 NaPF6. The electrode in NaFSA/MPPFSA demonstrated a reversible capacity of 1480 mAh g-1 and excellent capacity retention of 93% over 80 cycles, which is much better than those in the conventional electrolytes. The difference in capacity retention for the electrolytes correlates to the different solid electrolyte interphase (SEI) layer formed on the phosphorus electrode. To understand the SEI formation in NaFSA/MPPFSA and its evolution during cycling, we investigate the surface layer of the red phosphorus electrodes with hard X-ray photoelectron spectroscopy (HAXPES) and time-of-flight secondary ion mass spectrometry (TOF-SIMS). A detailed analysis of HAXPES spectra demonstrates that SEI layer consists of major inorganic and minor organic species, originating from decomposition of MPP+ and FSA-. Homogenous surface layer is formed during the first cycle in NaFSA/MPPFSA while in alkyl carbonate ester electrolytes, continuous growth of surface film up to the 20th cycle is observed. Possibility of red phosphorous electrode for battery applications with pure ionic liquid is discussed.

  15. Ab initio molecular dynamics simulations of organic electrolytes, electrodes, and lithium ion transport for Li-ion batteries

    Science.gov (United States)

    Kent, P. R. C.; Ganesh, P.; Jiang, De-En; Borodin, O.

    2012-02-01

    Optimizing the choice of electrolyte in lithium ion batteries and an understanding of the solid-electrolyte interphase (SEI) is required to optimize the balance between high-energy storage, high rate capability, and lifetime. We perform accurate ab initio molecular-dynamics simulations of common cyclic carbonates and LiPF6 to build solvation models which explain available Neutron and NMR spectroscopies. Our results corroborate why ethylene carbonate is a preferred choice for battery applications over propylene carbonate and how mixtures with dimethyl carbonate improve Li-ion diffusion. We study the role of functionalization of graphite-anode edges on the reducibility of the electrolyte and the ease of Li-ion intercalation at the initial stages of SEI formation. We find that oxygen terminated edges readily act as strong reductive sites, while hydrogen terminated edges are less reactive and allow faster Li diffusion. Orientational ordering of the solvent molecules precedes reduction at the interphase. Inorganic reductive components are seen to readily migrate to the anode edges, leading to increased surface passivation of the anode. We are currently quantifying Li-intercalation barriers across realistic SEI models, and progress along these lines will be presented.

  16. Anion exchange polymer electrolytes

    Science.gov (United States)

    Kim, Yu Seung; Kim, Dae Sik

    2015-06-02

    Anion exchange polymer electrolytes that include guanidinium functionalized polymers may be used as membranes and binders for electrocatalysts in preparation of anodes for electrochemical cells such as solid alkaline fuel cells.

  17. Investigating continuous co-intercalation of solvated lithium ions and graphite exfoliation in propylene carbonate-based electrolyte solutions

    Science.gov (United States)

    Song, Hee-Youb; Jeong, Soon-Ki

    2018-01-01

    Forming an effective solid electrolyte interphase (SEI) is a significant issue in lithium ion batteries that utilize graphite as a negative electrode material, because the SEI determines the reversibility of the intercalation and de-intercalation of lithium ions into graphite for secondary batteries. In propylene carbonate (PC)-based electrolyte solutions, ceaseless co-intercalation of solvated lithium ions takes place because no effective SEI is formed. It is indisputable that this continuous co-intercalation leads to graphite exfoliation; however, the reason for this is currently not well understood. In this study, we investigate interfacial reactions that contribute to SEI formation on highly oriented pyrolytic graphite (HOPG) in ethylene carbonate (EC) and PC-based electrolyte solutions by in situ atomic force microscopy. The blisters formed on HOPG after the decomposition of solvated lithium ions within the graphite layers do not change over the course of ten electrochemical cycles in an EC-based electrolyte solution. In contrast, when cycling in PC-based electrolytes, the blisters continually change, and the height at the vicinity of the graphite edge plane increases. These morphological changes are attributed to the continuous co-intercalation of solvated lithium ions in PC-based electrolyte solutions.

  18. A Tri-Layer Proton-Conducting Electrolyte for Chemically Stable Operation in Solid Oxide Fuel Cells

    KAUST Repository

    Bi, Lei

    2013-10-07

    Two BaZr0.7Pr0.1Y0.2O3-δ (BZPY) layers were used to sandwich a BaCe0.8Y0.2O3-δ (BCY) layer to produce a tri-layer electrolyte consisting of BZPY/BCY/BZPY. The BZPY layers significantly improved the chemical stability of the BCY electrolyte layer, which was not stable when tested alone, suggesting that the BZPY layer effectively protected the BCY layer from CO2 reaction, which is the major problem of BCY-based materials. A fuel cell with this sandwiched electrolyte supported on a Ni-based composite anode showed a reasonable cell performance, reaching 185 mW cm-2 at 700 oC, in spite of the relatively large electrolyte thickness (about 65 µm).

  19. Millimeter-wave irradiation heating for operation of doped CeO2 electrolyte-supported single solid oxide fuel cell

    Science.gov (United States)

    Che Abdullah, Salmie Suhana Binti; Teranishi, Takashi; Hayashi, Hidetaka; Kishimoto, Akira

    2018-01-01

    High operation temperature of solid oxide fuel cell (SOFC) results in high cell and operation cost, time consuming and fast cell degradation. Developing high performance SOFC that operates at lower temperature is required. Here we demonstrate 24 GHz microwave as a rapid heating source to replace conventional heating method for SOFC operation using 20 mol% Sm doped CeO2 electrolyte-supported single cell. The tested cell shows improvement of 62% in maximum power density at 630 °C under microwave heating. This improvement governs by bulk conductivity of the electrolyte. Investigation of ionic transference number reveals that the value is unchanged under microwave irradiation, confirming the charge carrier is dominated by oxygen ion species. This work shows a potential new concept of high performance as well as cost and energy effective SOFC.

  20. Extended UNIQUAC model for correlation and prediction of vapour-liquid-solid equilibria in aqueous salt systems containing non-electrolytes

    DEFF Research Database (Denmark)

    Iliuta, Maria C.; Thomsen, Kaj; Rasmussen, Peter

    2000-01-01

    to aqueous salt systems containing non-electrolytes in order to demonstrate its ability in representing solid-liquid-vapour (SLV) equilibrium and thermal property data for these strongly non-ideal systems. The model requires only pure component and binary temperature-dependent interaction parameters....... The calculations are based on an extensive database consisting of salt solubility data in pure and mixed solvents, VLE data for solvent mixtures and mixed solvent-electrolyte systems and thermal properties for mixed solvent solutions. Application of the model to the methanol-water system in the presence of several...... ions (Na+, K+, NH4+, Cl-, NO3-, SO42-, CO2- and HCO3-) shows that the Extended UNIQUAC model is able to give an accurate description of VLE and SLE in ternary add quaternary mixtures, using the name set of binary interaction parameters. The capability of the model to predict accurately the phase...

  1. Nanoscale CuO solid-electrolyte-based conductive-bridging, random-access memory cell with a TiN liner

    Science.gov (United States)

    Lee, Jong-Sun; Kim, Dong-Won; Kim, Hea-Jee; Jin, Soo-Min; Song, Myung-Jin; Kwon, Ki-Hyun; Park, Jea-Gun; Jalalah, Mohammed; Al-Hajry, Ali

    2018-01-01

    The Conductive-bridge random-access memory (CBRAM) cell is a promising candidate for a terabit-level non-volatile memory due to its remarkable advantages. We present for the first time TiN as a diffusion barrier in CBRAM cells for enhancing their reliability. CuO solid-electrolyte-based CBRAM cells implemented with a 0.1-nm TiN liner demonstrated better non-volatile memory characteristics such as 106 AC write/erase endurance cycles with 100-μs AC pulse width and a long retention time of 7.4-years at 85 °C. In addition, the analysis of Ag diffusion in the CBRAM cell suggests that the morphology of the Ag filaments in the electrolyte can be effectively controlled by tuning the thickness of the TiN liner. These promising results pave the way for faster commercialization of terabit-level non-volatile memories.

  2. Redefining the Food-Drug Interphase - REVIEW

    African Journals Online (AJOL)

    Bioactive Milk Peptides: Redefining the Food-Drug Interphase - REVIEW. Peer Reviewed ... in genetic engineering which means transgenic plants will be engineered to express ... milk affected both the immune system and the cell proliferation ...

  3. Enhanced performance of a quasi-solid-state dye-sensitized solar cell with aluminum nitride in its gel polymer electrolyte

    KAUST Repository

    Huang, Kuan-Chieh

    2011-08-01

    The effects of incorporation of aluminum nitride (AlN) in the gel polymer electrolyte (GPE) of a quasi-solid-state dye-sensitized solar cell (DSSC) were studied in terms of performance of the cell. The electrolyte, consisting of lithium iodide (LiI), iodine (I2), and 4-tert-butylpyridine (TBP) in 3-methoxypropionitrile (MPN), was solidified with poly(vinyidene fluoride-co-hexafluoro propylene) (PVDF-HFP). The 0.05, 0.1, 0.3, and 0.5 wt% of AlN were added to the electrolyte for this study. XRD analysis showed a reduction of crystallinity in the polymer PVDF-HFP for all the additions of AlN. The DSSC fabricated with a GPE containing 0.1 wt% AlN showed a short-circuit current density (JSC) and power-conversion efficiency (η) of 12.92±0.54 mA/cm2 and 5.27±0.23%, respectively, at 100 mW/cm2 illumination, in contrast to the corresponding values of 11.52±0.21 mA/cm2 and 4.75±0.08% for a cell without AlN. The increases both in JSC and in η of the promoted DSSC are attributed to the higher apparent diffusion coefficient of I- in its electrolyte (3.52×10-6 cm2/s), compared to that in the electrolyte without AlN of a DSSC (2.97×10-6 cm 2/s). At-rest stability of the quasi-solid-state DSSC with 0.1 wt% of AlN was found to decrease hardly by 5% and 7% at room temperature and at 40 °C, respectively, after 1000 h duration. The DSSC with a liquid electrolyte showed a decrease of about 40% at room temperature, while it virtually lost its performance in about 150 h at 40 °C. Explanations are further substantiated by means of electrochemical impedance spectroscopy (EIS), scanning electron microscopy (SEM), and by porosity measurements. © 2010 Elsevier B.V.

  4. Solid Electrolytes and Photoelectrolysis

    Science.gov (United States)

    1974-12-31

    these membranes causes cracking and the formation of leaks. Because /3- and /?"- 2 alumina are layer compounds, they have a highly anisotropic...occupancy of 8b and I6d positions. c. Carnegieites: The aluminosilicates are classic skeleton structures. The zeolites , for example, form molecular...3.20 per 10 Btu for fuel oil : 10 Btu X$0.40/gal =$3.20 . (2 x 10 Btu/lb) (6.5 lb/gal) Improved efficiencies for the

  5. Determination of Gibbs Energy of Mixing of Tungsten-Boron Binary System by Electromotive Force Measurement Using Solid Electrolyte

    Science.gov (United States)

    Yamamoto, Hiroaki; Morishita, Masao; Miyake, Yuta; Hiramatsu, Shusuke

    2017-06-01

    The thermodynamic properties for the tungsten-boron binary system were determined by measuring electromotive forces of galvanic cells using an Y2O3-stabilized ZrO2 solid oxide electrolyte. Assuming that W2B and αWB are the stoichiometric compounds, and W2B5- x and W1- x B3 are the nonstoichiometric compounds having solubility widths of 0.670 ≤ X B ≤ 0.690 and 0.805 ≤ X B ≤ 0.822, respectively, they were treated as the intermediate phases of W0.667B0.333, αW0.50B0.50, W0.330B0.670 W0.310B0.690, and W0.195B0.805 W0.178B0.822. The Gibbs energies of mixing, ∆mix G, determined in the present study are listed as follows: Δ_{{mix}} G({W}_{0.667} {B}_{0.333} )/{{J}} {{mol}}^{ - 1} = {-}78070 + 26.01T ± 70 [1305{-}1422{{ K}}(1032{-}1149°C)], Δ_{{mix}} G(α {W}_{0.50} {B}_{0.50} )/{{J}} {{mol}}^{ - 1} = {-}86140 + 20.19T ± 200 [1310{-}1399{{ K }}(1037{-}1126°C)], Δ_{{mix}} G({W}_{0.330} {B}_{0.670} )/{{J}} {{mol}}^{ - 1} = {-}78910 + 18.11T ± 200 [1228{-}1410{{ K }}(955{-}1137°C)], ; Δ_{{mix}} G({W}_{0.310} {B}_{0.690} )/{{J}} {{mol}}^{ - 1} = {-}77350 + 17.52T ± 500 [1228{-}1410{{ K }}(955{-}1137°C)], Δ_{{mix}} G({W}_{0.195} {B}_{0.805} )/{{J}} {{mol}}^{ - 1} = {-}63920 + 12.08T ± 500 [1170{-}1340{{ K }}(897{-}1067°C)], Δ_{{mix}} G({W}_{0.178} {B}_{0.822} )/{{J}} {{mol}}^{ - 1} = {-}60090 + 11.15T ± 200 [1170{-}1340{{ K }}(897{-}1067°C)]. Using the thermodynamic properties determined in the present study, the composition-oxygen partial pressure diagram of the tungsten-boron-oxygen system was constructed under the conditions at 1273 K (1000 °C) and a total pressure of 1 bar (100 kPa). It is useful to understand the oxidation property of tungsten-boron binary alloys.

  6. Enhanced ionic conductivity with Li{sub 7}O{sub 2}Br{sub 3} phase in Li{sub 3}OBr anti-perovskite solid electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Jinlong, E-mail: jlzhu04@physics.unlv.edu, E-mail: yusheng.zhao@unlv.edu, E-mail: zhaoys@sustc.edu.cn; Li, Shuai; Zhang, Yi; Howard, John W.; Wang, Yonggang; Kumar, Ravhi S.; Wang, Liping [High Pressure Science and Engineering Center, University of Nevada, Las Vegas, Nevada 89154 (United States); Lü, Xujie [Center for Integrated Nanotechnologies and Earth and Environmental Sciences Division, Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States); Li, Yutao [Materials Research Program and The Texas Materials Institute, University of Texas at Austin, Texas 78712 (United States); Zhao, Yusheng, E-mail: jlzhu04@physics.unlv.edu, E-mail: yusheng.zhao@unlv.edu, E-mail: zhaoys@sustc.edu.cn [High Pressure Science and Engineering Center, University of Nevada, Las Vegas, Nevada 89154 (United States); Department of Physics, South University of Science and Technology of China, Guangdong 518055 (China)

    2016-09-05

    Cubic anti-perovskites with general formula Li{sub 3}OX (X = Cl, Br, I) were recently reported as superionic conductors with the potential for use as solid electrolytes in all-solid-state lithium ion batteries. These electrolytes are nonflammable, low-cost, and suitable for thermoplastic processing. However, the primary obstacle of its practical implementation is the relatively low ionic conductivity at room temperature. In this work, we synthesized a composite material consisting of two anti-perovskite phases, namely, cubic Li{sub 3}OBr and layered Li{sub 7}O{sub 2}Br{sub 3,} by solid state reaction routes. The results indicate that with the phase fraction of Li{sub 7}O{sub 2}Br{sub 3} increasing to 44 wt. %, the ionic conductivity increased by more than one order of magnitude compared with pure phase Li{sub 3}OBr. Formation energy calculations revealed the meta-stable nature of Li{sub 7}O{sub 2}Br{sub 3}, which supports the great difficulty in producing phase-pure Li{sub 7}O{sub 2}Br{sub 3} at ambient pressure. Methods of obtaining phase-pure Li{sub 7}O{sub 2}Br{sub 3} will continue to be explored, including both high pressure and metathesis techniques.

  7. Polymer composite electrolytes having core-shell silica fillers with anion-trapping boron moiety in the shell layer for all-solid-state lithium-ion batteries.

    Science.gov (United States)

    Shim, Jimin; Kim, Dong-Gyun; Kim, Hee Joong; Lee, Jin Hong; Lee, Jong-Chan

    2015-04-15

    Core-shell silica particles with ion-conducting poly(ethylene glycol) and anion-trapping boron moiety in the shell layer were prepared to be used as fillers for polymer composite electrolytes based on organic/inorganic hybrid branched copolymer as polymer matrix for all-solid-state lithium-ion battery applications. The core-shell silica particles were found to improve mechanical strength and thermal stability of the polymer matrix and poly(ethylene glycol) and boron moiety in the shell layer increase compatibility between filler and polymer matrix. Furthermore, boron moiety in the shell layer increases both ionic conductivity and lithium transference number of the polymer matrix because lithium salt can be more easily dissociated by the anion-trapping boron. Interfacial compatibility with lithium metal anode is also improved because well-dispersed silica particles serve as protective layer against interfacial side reactions. As a result, all-solid-state battery performance was found to be enhanced when the copolymer having core-shell silica particles with the boron moiety was used as solid polymer electrolyte.

  8. Unraveling the electrolyte properties of Na3SbS4 through computation and experiment

    Science.gov (United States)

    Rush, Larry E.; Hood, Zachary D.; Holzwarth, N. A. W.

    2017-12-01

    Solid-state sodium electrolytes are expected to improve next-generation batteries on the basis of favorable energy density and reduced cost. Na3SbS4 represents a new solid-state ion conductor with high ionic conductivities in the mS/cm range. Here, we explore the tetragonal phase of Na3SbS4 and its interface with metallic sodium anode using a combination of experiments and first-principles calculations. The computed Na-ion vacancy migration energies of 0.1 eV are smaller than the value inferred from experiment, suggesting that grain boundaries or other factors dominate the experimental systems. Analysis of symmetric cells of the electrolyte—Na/Na 3SbS4/Na —show that a conductive solid electrolyte interphase forms. Computer simulations infer that the interface is likely to be related to Na3SbS3 , involving the conversion of the tetrahedral SbS43 - ions of the bulk electrolyte into trigonal pyramidal SbS33 - ions at the interface.

  9. Microwave-assisted reactive sintering and lithium ion conductivity of Li 1.3 Al 0.3 Ti 1.7 (PO 4 ) 3 solid electrolyte

    OpenAIRE

    Hallopeau, Leopold; Bregiroux, Damien; Rousse, Gwenaëlle; Portehault, David; Stevens, Philippe; Toussaint, Gwenaëlle; Laberty-Robert, Christel

    2018-01-01

    International audience; Li1.3Al0.3Ti1.7(PO4)3 (LATP) materials are made of a three−dimensional framework of TiO6 octahedra and PO4 tetrahedra, which provides several positions for Li+ ions. The resulting high ionic conductivity is promising to yield electrolytes for all-solid-state Li-ion batteries. In order to elaborate dense ceramics, conventional sintering methods often use high temperature (≥1000 °C) with long dwelling times (several hours) to achieve high relative density (∼90%). In this...

  10. Research activities in Shanghai Institute of Ceramics, Chinese Academy of Sciences on the solid electrolytes for sodium sulfur batteries

    Science.gov (United States)

    Wen, Zhaoyin; Gu, Zhonghua; Xu, Xiaohe; Cao, Jiadi; Zhang, Fuli; Lin, Zuxiang

    This paper presents the research and development of β″-Al 2O 3 ceramic electrolytes for sodium sulfur battery applications in the Shanghai Institute of Ceramics, Chinese Academy of Sciences (SICCAS). The process to prepare large size β″-Al 2O 3 ceramic tubes is described. Composite electrolytes with ZrO 2 as second phase additives are introduced. The strengthening and toughening effects of the second phase are significant. The results show that high quality β″-Al 2O 3 ceramic electrolytes with diameter as large as 60 mm and length of 500 mm are successfully produced. The composite of β″-Al 2O 3 and tetragonal ZrO 2 displayed much better mechanical properties than the pristine β″-Al 2O 3 ceramics.

  11. Reconfigurable Ion Gating of 2H-MoTe2 Field-Effect Transistors Using Poly(ethylene oxide)-CsClO4 Solid Polymer Electrolyte.

    Science.gov (United States)

    Xu, Huilong; Fathipour, Sara; Kinder, Erich W; Seabaugh, Alan C; Fullerton-Shirey, Susan K

    2015-05-26

    Transition metal dichalcogenides are relevant for electronic devices owing to their sizable band gaps and absence of dangling bonds on their surfaces. For device development, a controllable method for doping these materials is essential. In this paper, we demonstrate an electrostatic gating method using a solid polymer electrolyte, poly(ethylene oxide) and CsClO4, on exfoliated, multilayer 2H-MoTe2. The electrolyte enables the device to be efficiently reconfigured between n- and p-channel operation with ON/OFF ratios of approximately 5 decades. Sheet carrier densities as high as 1.6 × 10(13) cm(-2) can be achieved because of a large electric double layer capacitance (measured as 4 μF/cm(2)). Further, we show that an in-plane electric field can be used to establish a cation/anion transition region between source and drain, forming a p-n junction in the 2H-MoTe2 channel. This junction is locked in place by decreasing the temperature of the device below the glass transition temperature of the electrolyte. The ideality factor of the p-n junction is 2.3, suggesting that the junction is recombination dominated.

  12. Solid-state supercapacitors with ionic liquid gel polymer electrolyte based on poly (3, 4-ethylenedioxythiophene), carbon nanotubes, and metal oxides nanocomposites for electrical energy storage

    Science.gov (United States)

    Obeidat, Amr M.

    Clean and renewable energy systems have emerged as an important area of research having diverse and significant new applications. These systems utilize different energy storage methods such as the batteries and supercapacitors. Supercapacitors are electrochemical energy storage devices that are designed to bridge the gap between batteries and conventional capacitors. Supercapacitors which store electrical energy by electrical double layer capacitance are based on large surface area structured carbons. The materials systems in which the Faradaic reversible redox reactions store electrical energy are the transition metal oxides and electronically conducting polymers. Among the different types of conducting polymers, poly (3, 4- ethylenedioxythiophene) (PEDOT) is extensively investigated owing to its chemical and mechanical stability. Due to instability of aqueous electrolytes at high voltages and toxicity of organic electrolytes, potential of supercapacitors has not been fully exploited. A novel aspect of this work is in utilizing the ionic liquid gel polymer electrolyte to design solid-state supercapacitors for energy storage. Various electrochemical systems were investigated including graphene, PEDOT, PEDOT-carbon nanotubes, PEDOT-manganese oxide, and PEDOT-iron oxide nanocomposites. The electrochemical performance of solid-state supercapacitor devices was evaluated based on cyclic voltammetry (CV), charge-discharge (CD), prolonged cyclic tests, and electrochemical impedance spectroscopy (EIS) techniques. Raman spectroscopy technique was also utilized to analyze the bonding structure of the electrode materials. The graphene solid-state supercapacitor system displayed areal capacitance density of 141.83 mF cm-2 based on high potential window up to 4V. The PEDOT solid-state supercapacitor system was synthesized in acetonitrile and aqueous mediums achieving areal capacitance density of 219.17 mF cm-2. The hybrid structure of solid-state supercapacitors was also

  13. Improved Composite Gel Electrolyte by Layered Vermiculite for Quasi-Solid-State Dye-Sensitized Solar Cells

    Directory of Open Access Journals (Sweden)

    Hongcai He

    2014-01-01

    Full Text Available A composite quasisolid electrolyte is prepared by adding a layered vermiculite (VMT into the iodide/triiodide electrolyte including 4-tert-butylpyridine, which obviously improves the photovoltaic properties of quasisolid dye-sensitized solar cells (DSSCs. When adding 6 wt% VMT, the maximum photovoltaic conversion efficiency of 3.89% is obtained, which reaches more than two times greater than that without VMT. This enhancement effect is primarily explained by studying the Nyquist spectra, dark currents, and photovoltaic conversion efficiency.

  14. Extended UNIQUAC Model for Correlation and Prediction of Vapor-Liquid-Liquid-Solid Equilibria in Aqueous Salt Systems Containing Non-Electrolytes. Part B. Alcohol (Ethanol, Propanols, Butanols) - Water-salt systems

    DEFF Research Database (Denmark)

    Thomsen, Kaj; Iliuta, Maria Cornelia; Rasmussen, Peter

    2004-01-01

    -Redlich-Kwong equation of state. The model only requires binary, temperature-dependent interaction parameters. It has previously been used to describe the excess Gibbs energy for aqueous electrolyte mixtures and aqueous electrolyte systems containing methanol. It has been found to be an adequate model for representing......, and liquid-liquid equilibrium data for solvent mixtures and for mixed solvent-electrolyte systems. The application of this model to represent the vapor-liquid-liquid-solid equilibria in aqueous systems containing various non-electrolytes (ethanol, 1-propanol, 2-propanol, 1-butanol, 2- butanol, 2-methyl I...... solid-liquid-vapor equilibrium and thermal property data for strongly non-ideal systems. In this work, the model is extended to aqueous salt systems containing higher alcohols. The calculations are based on an extensive database consisting of salt solubility data, vapor liquid equilibrium data...

  15. Redox-Active Hydrogel Polymer Electrolytes with Different pH Values for Enhancing the Energy Density of the Hybrid Solid-State Supercapacitor.

    Science.gov (United States)

    Tang, Xiaohui; Lui, Yu Hui; Merhi, Abdul Rahman; Chen, Bolin; Ding, Shaowei; Zhang, Bowei; Hu, Shan

    2017-12-15

    To enhance the energy density of solid-state supercapacitors, a novel solid-state cell, made of redox-active poly(vinyl alcohol) (PVA) hydrogel electrolytes and functionalized carbon nanotube-coated cellulose paper electrodes, was investigated in this work. Briefly, acidic PVA-[BMIM]Cl-lactic acid-LiBr and neutral PVA-[BMIM]Cl-sodium acetate-LiBr hydrogel polymer electrolytes are used as catholyte and anolyte, respectively. The acidic condition of the catholyte contributes to suppression of the undesired irreversible reaction of Br- and extension of the oxygen evolution reaction potential to a higher value than that of the redox potential of Br-/Br3- reaction. The observed Br-/Br3- redox activity at the cathode contributes to enhance the cathode capacitance. The neutral condition of the anolyte helps extend the operating voltage window of the supercapacitor by introducing hydrogen evolution reaction overpotential to the anode. The electrosorption of nascent H on the negative electrode also increases the anode capacitance. As a result, the prepared solid-state hybrid supercapacitor shows a broad voltage window of 1.6 V, with a high Coulombic efficiency of 97.6% and the highest energy density of 16.3 Wh/kg with power density of 932.6 W/kg at 2 A/g obtained. After 10 000 cycles of galvanostatic charge and discharge tests at the current density of 10 A/g, it exhibits great cyclic stability with 93.4% retention of the initial capacitance. In addition, a robust capacitive performance can also be observed from the solid-state supercapacitor at different bending angles, indicating its great potential as a flexible energy storage device.

  16. The effects of lithium doping level on the structural, electrical properties of Li{sup +}-doped BPO{sub 4} solid electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Gao, Shan; Shui, Miao, E-mail: shuimiao@nbu.edu.cn; Zheng, Weidong; Yang, Tianci; Shu, Jie; Cheng, Liangliang; Feng, Lin; Ren, Yuanlong

    2013-08-01

    Graphical abstract: - Highlights: • Better ionic conductivities when 0.05 ≤ x ≤ 0.13. • V{sup ‴}{sub B}+3Li{sub i} model was preferred. • Grain size, lattice strain and Li{sup +}conductivity are closely related. - Abstract: A series of lithium ion conducting solid electrolytes Li{sub x}B{sub 1−x/3}PO{sub 4}(x = 0.01, 0.05, 0.09, 0.13, 0.17, 0.20) is synthesized by a soft-chemistry route. FTIR and XRD measurements reveal that the electrolyte is pure phase of tetragonal structure. AC-impedance spectroscopy (AC-IS) at room temperature shows that Li{sub x}B{sub 1−x/3}PO{sub 4} exhibits higher ionic conductivities in the range 0.05 ≤ x ≤ 0.13, beyond which, the ionic conductivities decrease quickly. Maximum ionic conductivity of the Li{sub x}B{sub 1−x/3}PO{sub 4} reaches 3.35 × 10{sup −5} S cm{sup −1} at room temperature for x = 0.05. Direct current polarizing (DCP) measurement indicates that the decomposition voltage for the solid electrolyte reaches up to 3.7 V. Micro-structure parameters of synthesized Li{sub x}B{sub 1−x/3}PO{sub 4} samples are calculated by Rietveld refinement of X-ray diffraction spectra. The unit-cell parameters, lattice strain, crystal grain size and ionic conductivities of the samples are correlated with the lithium ion doping level x.

  17. Evidence of the chemical stability of the garnet-type solid electrolyte Li5La3Ta2O12 towards lithium by a surface science approach

    Science.gov (United States)

    Fingerle, Mathias; Loho, Christoph; Ferber, Thimo; Hahn, Horst; Hausbrand, René

    2017-10-01

    The chemical stability between Li metal and garnet-type solid electrolytes is currently under debate, mainly catalyzed by theoretical studies. Here, we investigate the stability of Li5La3Ta2O12 (LLTaO) towards lithium experimentally. Using a surface science approach, lithium is stepwise evaporated on an LLTaO thin film grown by CO2-laser assisted chemical vapor deposition. By annealing of the LLTaO thin film, the Li2CO3 surface layer can be removed, leaving only small traces of Li2CO3, Li2O2 and Li2O behind. The interface formation of LLTaO towards lithium is then monitored by means of X-ray and ultraviolet photoelectron spectroscopy. Neither reaction products related to decomposition nor structural changes in the matrix of the Ta-based garnet-type solid-electrolyte can be detected, indicating that LLTaO exhibits chemical stability under equilibrium conditions. Furthermore, a model for the energy level alignment at the LLTaO/Li interface is discussed.

  18. Bi2O3 and La10Si6O27 composite electrolyte for enhanced performance in solid oxide fuel cells

    Science.gov (United States)

    Hairul Absah, H. Q. Hj; Abu Bakar, M. S.; Zaini, J. Hj; Azad, A.; Ming, L. C.

    2016-03-01

    Adding suitable metal oxide into lanthanum silicate apatite can produce a composite with a good oxygen ion-conducting electrolyte that enhances the performance of solid oxide fuel cells (SOFCs). In this paper we present the synthesis and characterisation of Bi2O3 and La10Si6O27 composite prepared by a solid state reaction. The sintering temperature of the composite was 1500°C for 10 hours with the heating and cooling rates of 10°C per minute. The properties of the resulting composite have been characterised by X-ray diffraction (XRD), scanning electron microscopy (SEM), and ionic conductivity measured by an a.c. impedance spectroscopy (IS). Rietveld refinement of XRD data shows that the composition is purely the mixture of Bi2O3 and La10Si6O27 with the unit cell parameters of the main phase as a = 9.9810 (8) and c = 7.3239 (6) Å. The room temperature crystal structure was hexagonal with space group P63/m. The highest ionic conductivity of 1.76 × 10-2 Scm-1 with a corresponding activation energy of 0.39 eV was obtained at 750°C. SEM images show the material is densed enough to use as an electrolyte for SOFCs.

  19. Manufacturing method of a metal interconnector for a solid electrolyte fuel cell; Kotai denkaishitsu nenryo denchiyo kinzoku intakonekuta no seizo hoh

    Energy Technology Data Exchange (ETDEWEB)

    Takatsuki, S.; Kuru, C. [Mitsubishi Heavy Industries Ltd., Tokyo (Japan); Kosaka, K. [Mitsubishi Heavy Industries Ltd., Nagasaki (Japan). Nagasaki Technical Inst.

    1996-04-30

    A previous metal interconnector for a solid electrolyte fuel cell is exposed to both of oxidative and reductive environments so that ceramic coating has been proposed for the improvement of the oxidation resistance, but the metal interconnector cannot tolerate long-term operation due to cracks and exfoliation by thermal stress caused by the difference of the thermal expansion coefficients from the metal after repeated thermal cycle accompanied by starting and stopping. This invention aims to solve this problem and to present a manufacturing method of a metal interconnector for a solid electrolyte fuel cell formed with dense ceramic coating of good adhesion. In this invention, each surface of a metallic material produced in a prescribed shape to be equipped with the fuel electrode and the air electrode is applied with blast treatment followed by the formation of ceramic spraying deposit on the each surface. This procedure improves the adhesion of the metal matrix with the ceramic spraying deposit and enables to improve the heat cycle resistance. 4 figs.

  20. Controllable growth of nanoscale conductive filaments in solid-electrolyte-based ReRAM by using a metal nanocrystal covered bottom electrode.

    Science.gov (United States)

    Liu, Qi; Long, Shibing; Lv, Hangbing; Wang, Wei; Niu, Jiebin; Huo, Zongliang; Chen, Junning; Liu, Ming

    2010-10-26

    Resistive memory (ReRAM) based on a solid-electrolyte insulator is a promising nanoscale device and has great potentials in nonvolatile memory, analog circuits, and neuromorphic applications. The underlying resistive switching (RS) mechanism of ReRAM is suggested to be the formation and rupture of nanoscale conductive filament (CF) inside the solid-electrolyte layer. However, the random nature of the nucleation and growth of the CF makes their formation difficult to control, which is a major obstacle for ReRAM performance improvement. Here, we report a novel approach to resolve this challenge by adopting a metal nanocrystal (NC) covered bottom electrode (BE) to replace the conventional ReRAM BE. As a demonstration vehicle, a Ag/ZrO(2)/Cu NC/Pt structure is prepared and the Cu NC covered Pt BE can control CF nucleation and growth to provide superior uniformity of RS properties. The controllable growth of nanoscale CF bridges between Cu NC and Ag top electrode has been vividly observed by transmission electron microscopy (TEM). On the basis of energy-dispersive X-ray spectroscopy (EDS) and elemental mapping analyses, we further confirm that the chemical contents of the CF are mainly Ag atoms. These testing/metrology results are consistent with the simulation results of electric-field distribution, showing that the electric field will enhance and concentrate on the NC sites and control location and orientation of Ag CFs.

  1. Area-Controllable Stamping of Semicrystalline Copolymer Ionogels for Solid-State Electrolyte-Gated Transistors and Light-Emitting Devices.

    Science.gov (United States)

    Kim, Hyun Je; Yang, Hae Min; Koo, Jaemok; Kang, Moon Sung; Hong, Kihyon; Lee, Keun Hyung

    2017-12-13

    Two types of thin-film electrochemical devices (electrolyte-gated transistors and electrochemical light-emitting cells) are demonstrated using area-controllable ionogel patches generated by transfer-stamping. For the successful transfer of ionogel patches on various target substrates, thermoreversible gelation by phase-separated polymer crystals within the ionogel is essential because it allows the gel to form a conformal contact with the acceptor substrate, thereby lowering the overall Gibbs energy of the system upon transfer of the ionogel. This crystallization-mediated stamping provides a much more efficient deposition route for producing thin films of ionically conductive high-capacitance solid ionogel electrolytes. The lateral dimensions of the transferred ionogels range from 1 mm × 1 mm to 40 mm × 40 mm. These ionogel patches are incorporated in organic p-type and inorganic n-type thin-film transistors and electrochemical light-emitting devices. The resulting transistors show sub-1 V device operation with high transconductance currents, and the optoelectronic devices emit orange light through a series of electrochemical redox reactions. These results demonstrate a simple yet versatile route to employ physical ionogels for various solid-state electrochemical device applications.

  2. POLYMER ELECTROLYTE MEMBRANE FUEL CELLS

    DEFF Research Database (Denmark)

    2001-01-01

    A method for preparing polybenzimidazole or polybenzimidazole blend membranes and fabricating gas diffusion electrodes and membrane-electrode assemblies is provided for a high temperature polymer electrolyte membrane fuel cell. Blend polymer electrolyte membranes based on PBI and various...... thermoplastic polymers for high temperature polymer electrolyte fuel cells have also been developed. Miscible blends are used for solution casting of polymer membranes (solid electrolytes). High conductivity and enhanced mechanical strength were obtained for the blend polymer solid electrolytes...... electrolyte membrane by hot-press. The fuel cell can operate at temperatures up to at least 200 °C with hydrogen-rich fuel containing high ratios of carbon monoxide such as 3 vol% carbon monoxide or more, compared to the carbon monoxide tolerance of 10-20 ppm level for Nafion$m(3)-based polymer electrolyte...

  3. NUMERICAL ANALYSIS OF INTER-PHASE MASS TRANSFER ...

    African Journals Online (AJOL)

    NUMERICAL ANALYSIS OF INTER-PHASE MASS TRANSFER WITH. CHEMICAL REACTION. Nigus Gabbiye, Nurelegne Tefera and Daggupati Venkata Narasaiah. Department of Chemical Engineering. Addis Ababa University. ABSTRACT. The numerical analysis in' the present study simulates interphase mass transfer ...

  4. Separators for Li-Ion and Li-Metal Battery Including Ionic Liquid Based Electrolytes Based on the TFSI− and FSI− Anions

    Science.gov (United States)

    Kirchhöfer, Marija; von Zamory, Jan; Paillard, Elie; Passerini, Stefano

    2014-01-01

    The characterization of separators for Li-ion or Li-metal batteries incorporating hydrophobic ionic liquid electrolytes is reported herein. Ionic liquids made of N-butyl-N-methylpyrrolidinium (PYR14+) or N-methoxyethyl-N-methylpyrrolidinium (PYR12O1+), paired with bis(trifluoromethanesulfonyl)imide (TFSI−) or bis(fluorosulfonyl)imide (FSI−) anions, were tested in combination with separators having different chemistries and morphologies in terms of wetting behavior, Gurley and McMullin number, as well as Li/(Separator + Electrolyte) interfacial properties. It is shown that non-functionalized microporous polyolefin separators are poorly wetted by FSI−-based electrolytes (contrary to TFSI−-based electrolytes), while the ceramic coated separator Separion® allows good wetting with all electrolytes. Furthermore, by comparing the lithium solid electrolyte interphase (SEI) resistance evolution at open circuit and during cycling, depending on separator morphologies and chemistries, it is possible to propose a scale for SEI forming properties in the order: PYR12O1FSI > PYR14FSI > PYR14TFSI > PYR12O1TFSI. Finally, the impact the separator morphology is evidenced by the SEI resistance evolution and by comparing Li electrodes cycled using separators with two different morphologies. PMID:25153637

  5. Separators for Li-Ion and Li-Metal Battery Including Ionic Liquid Based Electrolytes Based on the TFSI− and FSI− Anions

    Directory of Open Access Journals (Sweden)

    Marija Kirchhöfer

    2014-08-01

    Full Text Available The characterization of separators for Li-ion or Li-metal batteries incorporating hydrophobic ionic liquid electrolytes is reported herein. Ionic liquids made of N-butyl-N-methylpyrrolidinium (PYR14+ or N-methoxyethyl-N-methylpyrrolidinium (PYR12O1+, paired with bis(trifluoromethanesulfonylimide (TFSI− or bis(fluorosulfonylimide (FSI− anions, were tested in combination with separators having different chemistries and morphologies in terms of wetting behavior, Gurley and McMullin number, as well as Li/(Separator + Electrolyte interfacial properties. It is shown that non-functionalized microporous polyolefin separators are poorly wetted by FSI−-based electrolytes (contrary to TFSI−-based electrolytes, while the ceramic coated separator Separion® allows good wetting with all electrolytes. Furthermore, by comparing the lithium solid electrolyte interphase (SEI resistance evolution at open circuit and during cycling, depending on separator morphologies and chemistries, it is possible to propose a scale for SEI forming properties in the order: PYR12O1FSI > PYR14FSI > PYR14TFSI > PYR12O1TFSI. Finally, the impact the separator morphology is evidenced by the SEI resistance evolution and by comparing Li electrodes cycled using separators with two different morphologies.

  6. A study of ferrocene diffusion dynamics in network poly(ethylene oxide) polymer electrolyte by solid-state voltammetry

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, M.; Longmire, M.L.; Murray, R.W. (Univ. of North Carolina, Chapel Hill (USA))

    1990-03-22

    The diffusion rates of five ferrocene derivatives dissolved in an amorphous, cross-linked poly(ethylene oxide) (PEO) polymer electrolyte are measured by an electrochemical technique which detects the rate of their transport to an oxidizing microdisk electrode. The diffusion coefficients in dilute ferrocene/polymer solutions at 65{degree}C vary from 3 {times} 10{sup {minus}7} to 2 {times} 10{sup {minus}8} cm{sup 2} s{sup {minus}1} depending on the size of the ferrocene derivative. The diffusion coefficients decrease with increasing ferrocene concentration, increasing LiClO{sub 4} electrolyte concentration, and decreasing temperature; values approaching 10{sup {minus}10} cm{sup 2} s{sup {minus}1} are encountered at room temperature.

  7. Insights into the Self-assembly of Two Diamine Derivatives Low Molecular Mass Organogelators in Quasi-solid-state Electrolytes

    Science.gov (United States)

    Mo, Shu-Fan; Zhang, Bing; Zhou, Kai-Xuan; Yao, Jian-Xi; Dai, Song-Yuan

    2016-05-01

    Electrolyte materials are the key components in dye-sensitized solar cells and are very crucial to the performance and long-term stability of the cells. The diamide derivatives have been proved in our lab to be effective to improve the stability of the traditional liquid electrolyte as low molecular mass organogelator (LMOGs). Our previous experiments and simulations indicated that the relationship between the morphology of the electrolyte and the self-assembly of the LMOGs. In the current study, the self-assembly of two diamine derivatives (N,N'-1,8-octanediylbis-dodecanamide and N,N'-1,9-nonanediylbis-dodecanamide) has been investigated and characterized using molecular dynamics. Although the structure of the two these molecules is only different in one methylene, the simulations revealed that the self-assembly patterns of the two diamine derivatives are quite different. The differences seems to be suitable to explain the diverse morphologies formed by the assembly of the LMOGs.

  8. Direct ceramic inkjet printing of yttria-stabilized zirconia electrolyte layers for anode-supported solid oxide fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Tomov, R.I.; Hopkins, S.C. [Applied Superconductivity and Cryoscience Group, Department of Materials Science and Metallurgy, University of Cambridge, Cambridge CB4 3QZ (United Kingdom); Krauz, M.; Kluczowski, J.R. [Institute of Power Engineering, Ceramic Department CEREL, 36-040 Boguchwala (Poland); Jewulski, J. [Institute of Power Engineering, Fuel Cells Department, 02-981 Warsaw (Poland); Glowacka, D.M. [Detector Physics Group, Cavendish Laboratory, University of Cambridge, Cambridge CB3 0HE (United Kingdom); Glowacki, B.A. [Applied Superconductivity and Cryoscience Group, Department of Materials Science and Metallurgy, University of Cambridge, Cambridge CB4 3QZ (United Kingdom); Institute of Power Engineering, Fuel Cells Department, 02-981 Warsaw (Poland)

    2010-11-01

    Electromagnetic drop-on-demand direct ceramic inkjet printing (EM/DCIJP) was employed to fabricate dense yttria-stabilized zirconia (YSZ) electrolyte layers on a porous NiO-YSZ anode support from ceramic suspensions. Printing parameters including pressure, nozzle opening time and droplet overlapping were studied in order to optimize the surface quality of the YSZ coating. It was found that moderate overlapping and multiple coatings produce the desired membrane quality. A single fuel cell with a NiO-YSZ/YSZ ({proportional_to}6 {mu}m)/LSM + YSZ/LSM architecture was successfully prepared. The cell was tested using humidified hydrogen as the fuel and ambient air as the oxidant. The cell provided a power density of 170 mW cm{sup -2} at 800 C. Scanning electron microscopy (SEM) revealed a highly coherent dense YSZ electrolyte layer with no open porosity. These results suggest that the EM/DCIJP inkjet printing technique can be successfully implemented to fabricate electrolyte coatings for SOFC thinner than 10 {mu}m and comparable in quality to those fabricated by more conventional ceramic processing methods. (author)

  9. Interrelationships among Grain Size, Surface Composition, Air Stability, and Interfacial Resistance of Al-Substituted Li7La3Zr2O12 Solid Electrolytes.

    Science.gov (United States)

    Cheng, Lei; Wu, Cheng Hao; Jarry, Angelique; Chen, Wei; Ye, Yifan; Zhu, Junfa; Kostecki, Robert; Persson, Kristin; Guo, Jinghua; Salmeron, Miquel; Chen, Guoying; Doeff, Marca

    2015-08-19

    The interfacial resistances of symmetrical lithium cells containing Al-substituted Li7La3Zr2O12 (LLZO) solid electrolytes are sensitive to their microstructures and histories of exposure to air. Air exposure of LLZO samples with large grain sizes (∼150 μm) results in dramatically increased interfacial impedances in cells containing them, compared to those with pristine large-grained samples. In contrast, a much smaller difference is seen between cells with small-grained (∼20 μm) pristine and air-exposed LLZO samples. A combination of soft X-ray absorption (sXAS) and Raman spectroscopy, with probing depths ranging from nanometer to micrometer scales, revealed that the small-grained LLZO pellets are more air-stable than large-grained ones, forming far less surface Li2CO3 under both short- and long-term exposure conditions. Surface sensitive X-ray photoelectron spectroscopy (XPS) indicates that the better chemical stability of the small-grained LLZO is related to differences in the distribution of Al and Li at sample surfaces. Density functional theory calculations show that LLZO can react via two different pathways to form Li2CO3. The first, more rapid, pathway involves a reaction with moisture in air to form LiOH, which subsequently absorbs CO2 to form Li2CO3. The second, slower, pathway involves direct reaction with CO2 and is favored when surface lithium contents are lower, as with the small-grained samples. These observations have important implications for the operation of solid-state lithium batteries containing LLZO because the results suggest that the interfacial impedances of these devices is critically dependent upon specific characteristics of the solid electrolyte and how it is prepared.

  10. Interface Re-Engineering of Li10GeP2S12 Electrolyte and Lithium anode for All-Solid-State Lithium Batteries with Ultralong Cycle Life.

    Science.gov (United States)

    Zhang, Zhihua; Chen, Shaojie; Yang, Jing; Wang, Junye; Yao, Lili; Yao, Xiayin; Cui, Ping; Xu, Xiaoxiong

    2018-01-24

    An ingenious interface re-engineering strategy was applied to in situ prepare a manipulated LiH2PO4 protective layer on the surface of Li anode for circumventing the intrinsic chemical stability issues of Li10GeP2S12 (LGPS) to Li metal, specifically the migration of mixed ionic-electronic reactants to the inner of LGPS, and the kinetically sluggish reactions in the interface. As consequence, the stability of LGPS with Li metal increased substantially and the cycling of symmetric Li/Li cell showed that the polarization voltage could keep relative stable for over 950 h at 0.1 mA cm-2 within ±0.05 V. The optimized ASSLiB of LiCoO2 (LCO)/LGPS/Li with interface-engineered structure was able to deliver long cycle life and high capacity, i.e., a reversible discharge capacity of 131.1 mAh g-1 at the initial cycle and 113.7 mAh g-1 at the 500th cycle under 0.1 C with a retention of 86.7%. In addition, the factors effected on the interphases formation of the LGPS/Li interface were analyzed, and the mechanism of the stability between LGPS and Li anode with protective layer was further investigated. Moreover, the probable causes of battery degradation were also explored. Above all, this work would give an alternative strategy for the modification of Li anode in high energy density solid-state lithium metal batteries.

  11. Study on (100-x)(70Li2S-30P2S5)-xLi2ZrO3 glass-ceramic electrolyte for all-solid-state lithium-ion batteries

    Science.gov (United States)

    Lu, Penghao; Ding, Fei; Xu, Zhibin; Liu, Jiaquan; Liu, Xingjiang; Xu, Qiang

    2017-07-01

    A novel glass-ceramic electrolyte of (100-x)(70Li2S-30P2S5)-xLi2ZrO3 (x = 0, 1, 2, 5) is successfully prepared by a vibratory ball-milling method and followed by a heat-treatment process. Composition of the ternary sulfide electrolyte and the heat-treatment process are optimized by physical characterizations and electrochemical measurements. The testing results show that the optimal substitution quantity of Li2ZrO3 into the Li2S-P2S5 electrolyte substrate is 1 mol %. An appropriate heat-treatment temperature of 99(70Li2S-30P2S5)-1Li2ZrO3 glass-ceramic electrolyte is 285 °C. Among the as-prepared ternary electrolyte samples, 99(70Li2S-30P2S5)-1Li2ZrO3 glass-ceramic electrolyte may exhibit the highest conductivity of 2.85 × 10-3 S cm-1 at room temperature, which is much higher than that of the 70Li2S-30P2S5 glass-ceramic electrolyte. Compared to that of the all-solid-state lithium-ion battery of LiCoO2/70Li2S-30P2S5/In-Li, discharge capacities of all-solid-state lithium-ion battery of LiCoO2/99(70Li2S-30P2S5)-1Li2ZrO3/In-Li may increase 41.0% at the 10th charge-discharge cycle and 21.9% at the 50th charge-discharge cycle, respectively. Furthermore, electrochemical impedance spectroscopy (EIS) analyses of all-solid-state lithium-ion batteries reveal that addition of Li2ZrO3 into the Li2S-P2S5 electrolyte substrate may decrease the interfacial resistance between the electrodes and solid electrolyte. The improvement of electrochemical performances of 99(70Li2S-30P2S5)-1Li2ZrO3 glass-ceramic electrolyte is ascribed to both the stable crystal structure and a high lithium-ion diffusion coefficient of Li2ZrO3.

  12. Polymer Electrolytes

    Science.gov (United States)

    Hallinan, Daniel T.; Balsara, Nitash P.

    2013-07-01

    This review article covers applications in which polymer electrolytes are used: lithium batteries, fuel cells, and water desalination. The ideas of electrochemical potential, salt activity, and ion transport are presented in the context of these applications. Potential is defined, and we show how a cell potential measurement can be used to ascertain salt activity. The transport parameters needed to fully specify a binary electrolyte (salt + solvent) are presented. We define five fundamentally different types of homogeneous electrolytes: type I (classical liquid electrolytes), type II (gel electrolytes), type III (dry polymer electrolytes), type IV (dry single-ion-conducting polymer electrolytes), and type V (solvated single-ion-conducting polymer electrolytes). Typical values of transport parameters are provided for all types of electrolytes. Comparison among the values provides insight into the transport mechanisms occurring in polymer electrolytes. It is desirable to decouple the mechanical properties of polymer electrolyte membranes from the ionic conductivity. One way to accomplish this is through the development of microphase-separated polymers, wherein one of the microphases conducts ions while the other enhances the mechanical rigidity of the heterogeneous polymer electrolyte. We cover all three types of conducting polymer electrolyte phases (types III, IV, and V). We present a simple framework that relates the transport parameters of heterogeneous electrolytes to homogeneous analogs. We conclude by discussing electrochemical stability of electrolytes and the effects of water contamination because of their relevance to applications such as lithium ion batteries.

  13. Reactivity between La(Sr)FeO{sub 3} cathode, doped CeO{sub 2} interlayer and yttria-stabilized zirconia electrolyte for solid oxide fuel cell applications

    Energy Technology Data Exchange (ETDEWEB)

    Martinez-Amesti, Ana; Larranaga, Aitor; Aguayo, Andres T.; Pizarro, Jose L.; No, Maria L.; Arriortua, Maria I. [University of the Basque Country (UPV/EHU), Faculty of Science and Technology, B. Sarriena S/N, 48940 Leioa, Vizcaya (Spain); Rodriguez-Martinez, Lide M.; Laresgoiti, Ander [Ikerlan-Energia, Centro Tecnologico, Parque Tecnologico de Alava, Juan de la Cierva 1, 01510 Minano (Spain)

    2008-10-15

    Detailed X-ray diffraction (XRD) analysis of two different Sr-doped LaFeO{sub 3} cathodes, YSZ electrolyte and two Sm/Gd-doped CeO{sub 2} interlayer and their mixtures were used to evaluate the formation of undesired secondary reaction compounds. The analysis of room temperature X-ray diffraction data of the mixtures indicates the crystallization of strontium and/or lanthanum zirconates between the cathode and the electrolyte materials and no detected reaction between the cathode and the interlayer materials. For all the ferrite mixtures a significant shift in the diffraction peaks is observed, which is the result of the unit cell volume expansion and contraction of the cathode (LSF) structures mixed with electrolyte (YSZ), and with interlayers (SDC, GDC), respectively. On the other hand, a complete solid solution was observed between the crystal structures of YSZ electrolyte and SDC or GDC interlayers. The observed cell modifications for the ferrite mixtures were the result of the incorporation of Zr and Ce, in the B and A type positions of the perovskite structure, respectively. The electrolyte/interlayer interface shows the presence of intermediate compositions at high temperature. The electrochemical studies show better results when a Sm-doped CeO{sub 2} is inserted between the cathode and electrolyte material. The best result obtained is for the half-cell prepared with LSF-40 and SDC interlayer on YSZ electrolyte. (author)

  14. High resolution analysis of interphase chromosome domains

    NARCIS (Netherlands)

    Visser, A. E.; Jaunin, F.; Fakan, S.; Aten, J. A.

    2000-01-01

    Chromosome territories need to be well defined at high resolution before functional aspects of chromosome organization in interphase can be explored. To visualize chromosomes by electron microscopy (EM), the DNA of Chinese hamster fibroblasts was labeled in vivo with thymidine analogue BrdU. Labeled

  15. Quasi-solid state electrolyte for semi-transparent bifacial dye-sensitized solar cell with over 10% power conversion efficiency

    Science.gov (United States)

    Hwang, Dae-Kue; Nam, Jung Eun; Jo, Hyo Jeong; Sung, Shi-Joon

    2017-09-01

    In traditional dye-sensitized solar cells (DSSCs), the liquid electrolyte (LE) presents a problem for long-term stability. Herein, we demonstrate a bifacial DSSC by combining a new metal-free organic dye and a quasi-solid state electrolyte (QSSE) that contains poly(vinylidenefluoride-co-hexafluoropropylene) (PVdF-HFP)-based polymer gel. The incident light irradiates the front side of the DSSC, and the transmitted light is reused after reflection on the back side. Owing to the semi-transparent DSSC electrode, the reflected light can penetrate and be absorbed by the dye molecules in the DSSC, thereby enhancing the short-circuit current density and thus the overall power conversion efficiency (PCE). The PCE for the DSSC device with QSSE from bifacial irradiation is 10.37%, a value that is comparable to that obtained with LE-based DSSC (9.89%). The stability of the device is enhanced when the polymer gel containing PVdF-HFP is mixed with the LE, and the effectiveness of PVdF-HFP as a gelator is attributed to its interaction with the Li+ ions. Based on our preliminary results, this architecture can lead to more stable bifacial QSSE-based DSSCs without sacrificing the photovoltaic performance.

  16. CdSe Quantum Dots Sensitized Mesoporous TiO2 Solar Cells with CuSCN as Solid-State Electrolyte

    Directory of Open Access Journals (Sweden)

    Guanbi Chen

    2011-01-01

    Full Text Available Mesoporous TiO2 is functionalized by 3-mercaptopropyl trimethyoxysilane (MPTMS to anchor CdSe quantum dots (QDs. The resulting TiO2/CdSe is combined with solid-state electrolyte (CuSCN to form solar cells. It is found that the efficiency of electron injection from QDs to TiO2 can be improved owing to the substitution of the long chains of organic capping agents at the surface of QDs with MPTMS. The hydrolyzate of MPTMS forms an insulating barrier layer to reduce the recombination at the TiO2/CdSe interface, leading to the increase of open-circuit voltage (Voc.

  17. Operation of Thin-Film Electrolyte Metal-Supported Solid Oxide Fuel Cells in Lightweight and Stationary Stacks: Material and Microstructural Aspects

    Directory of Open Access Journals (Sweden)

    Daniel Roehrens

    2016-09-01

    Full Text Available In this study we report on the development and operational data of a metal-supported solid oxide fuel cell with a thin film electrolyte under varying conditions. The metal-ceramic structure was developed for a mobile auxiliary power unit and offers power densities of 1 W/cm2 at 800 °C, as well as robustness under mechanical, thermal and chemical stresses. A dense and thin yttria-doped zirconia layer was applied to a nanoporous nickel/zirconia anode using a scalable adapted gas-flow sputter process, which allowed the homogeneous coating of areas up to 100 cm2. The cell performance is presented for single cells and for stack operation, both in lightweight and stationary stack designs. The results from short-term operation indicate that this cell technology may be a very suitable alternative for mobile applications.

  18. Mechanical properties at the nanometer scale of GDC and YSZ used as electrolytes for solid oxide fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Morales, M., E-mail: mmorales@ub.edu [Departamento de Ciencia de los Materiales e Ingenieria Metalurgica, Universidad de Barcelona, C/Marti i Franques, 1 08028 Barcelona (Spain)] [Instituto de Ciencia de los Materiales de Barcelona, ICMAB-CSIC, Campus de la UAB, 08193 Bellaterra, Barcelona (Spain); Roa, J.J.; Capdevila, X.G.; Segarra, M. [Departamento de Ciencia de los Materiales e Ingenieria Metalurgica, Universidad de Barcelona, C/Marti i Franques, 1 08028 Barcelona (Spain); Pinol, S. [Instituto de Ciencia de los Materiales de Barcelona, ICMAB-CSIC, Campus de la UAB, 08193 Bellaterra, Barcelona (Spain)

    2010-04-15

    The Young's modulus (E), hardness (H) and fracture toughness (K{sub IC}) of various compositions of gadolinia doped-ceria (GDC, Gd{sub x}Ce{sub 1-x}O{sub 2-x/2}, 0.1 {<=} x {<=} 0.2) and yttria-stabilized zirconia (YSZ, Y{sub 0.08}Zr{sub 0.92}O{sub 1.96}) electrolytes were investigated by nanoindentation. All samples were produced by the sol-gel method, formed by uniaxial pressure and sintered at 1400 deg. C. In order to determine the mechanical properties, a Berkovich diamond tip was employed at applied loads of 5, 10, 30, 100 and 500 mN. The results were interpreted by the Oliver-Pharr method and values of K{sub IC} were determined using the method of Palmqvist cracks. The residual imprints were observed by field emission scanning electron microscopy. The results obtained showed that the H, E and K{sub IC} of GDC decreased with increasing gadolinia concentration, due to the oxygen vacancies generated by the dopant addition. As a result, the mechanical properties of GDC were significantly lower than those of YSZ electrolyte.

  19. Separating bulk from grain boundary Li ion conductivity in the sol–gel prepared solid electrolyte Li1.5Al0.5Ti1.5(PO4)3

    OpenAIRE

    Breuer, Stefan; Prutsch, Denise; Ma, Qianli; Epp, Viktor; Preishuber-Pflügl, Florian; Tietz, Frank; Wilkening, Martin

    2015-01-01

    Lithium aluminium titanium phosphate (LATP) belongs to one of the most promising solid electrolytes. Besides sufficiently high electrochemical stability, its use in lithium-based all-solid-state batteries crucially depends on the ionic transport properties. While many impedance studies can be found in literature that report on overall ion conductivities, a discrimination of bulk and grain boundary electrical responses via conductivity spectroscopy has rarely been reported so far. Here, we too...

  20. Co-solvents with high coulombic efficiency in propylene carbonate based electrolytes

    Science.gov (United States)

    Liu, Gao; Zhao, Hui; Park, Sang-Jae

    2017-06-27

    A homologous series of cyclic carbonate or propylene carbonate (PC) analogue solvents with increasing length of linear alkyl substitutes were synthesized and used as co-solvents with PC for graphite based lithium ion half cells. A graphite anode reaches a capacity around 310 mAh/g in PC and its analogue co-solvents with 99.95% Coulombic efficiency. Cyclic carbonate co-solvents with longer alkyl chains are able to prevent exfoliation of graphite when used as co-solvents with PC. The cyclic carbonate co-solvents of PC compete for solvation of Li ion with PC solvent, delaying PC co-intercalation. Reduction products of PC on graphite surfaces via single-electron path form a stable Solid Electrolyte Interphase (SEI), which allows the reversible cycling of graphite.

  1. Improvements of photocurrent by using modified SiO(2) in the poly(ether urethane)/poly(ethylene oxide) polymer electrolyte for all-solid-state dye-sensitized solar cells.

    Science.gov (United States)

    Zhou, Yanfang; Xiang, Wanchun; Chen, Shen; Fang, Shibi; Zhou, Xiaowen; Zhang, Jingbo; Lin, Yuan

    2009-07-14

    Nanocomposite polymer electrolytes containing poly(ether urethane) (PEUR)/poly(ethylene oxide) (PEO)/modified SiO(2) were prepared for all-solid-state dye-sensitized solar cells with a high efficiency of 4.86% and an active area of 0.25 cm(2) under AM1.5 conditions at 100 mW cm(-2) irradiation.

  2. Performance evaluation of solid oxide fuel cells with thin film electrolyte fabricated by binder-assisted slurry casting

    Energy Technology Data Exchange (ETDEWEB)

    Guo, W.M.; Liu, X.M.; Li, L.J. [Department of Biological and Chemical Engineering, Guangxi University of Technology, Liuzhou 545006 (China); Xiao, Y.F. [Department of Stomatology, Liuzhou Maternity and Child Health Hospital, Liuzhou 545001 (China); Chen, Y. [School of Yingdong Life Science, Shaoguan University, Shaoguan 512005 (China)

    2011-10-15

    A gas-tight yttria-stabilized zirconia (YSZ) electrolyte film was fabricated on porous NiO-YSZ anode substrates by a binder-assisted slurry casting technique. The scanning electron microscope (SEM) results showed that the YSZ film was relatively dense with a thickness of 10 {mu}m. La{sub 0.8}Sr{sub 0.2}MnO{sub 3} (LSM)-YSZ was applied to cathode using a screen-print technique and the single fuel cells were tested in a temperature range from 600 to 800 C. An open circuit voltage (OCV) of over 1.0 V was observed. The maximum power densities at 600, 700, and 800 C were 0.13, 0.44, and 1.1 W cm{sup -2}, respectively. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  3. The counterintuitive impact of separator-electrolyte combinations on the cycle life of graphite-silicon composite electrodes

    Science.gov (United States)

    Schott, Tiphaine; Gómez-Cámer, Juan Luis; Bünzli, Christa; Novák, Petr; Trabesinger, Sigita

    2017-03-01

    Thin polymeric membranes such as Celgard are commonly used as separators in Li-ion batteries to ensure high volumetric energy density. Independently, for silicon-based electrodes fluoroethylene carbonate (FEC) is often added to the electrolyte to improve the cycling stability of the cell. Here we demonstrate that, counterintuitively, this separator-electrolyte combination negatively affects the performance of graphite-Si electrodes in half-cells. In a statistical evaluation of the cycling behavior of C-Si electrode cells with various separators and either with or without FEC addition, we show that by improving the solid electrolyte interphase on the silicon particles, FEC addition leads to inhomogeneous current distribution in the electrodes, therefore favoring lithium dendrite growth and leading to irreversible failure with Celgard. In contrast, self-recovery is observed with simple glass-fiber separators. Without FEC, neither dendrites nor failure are observed, but cells with Celgard suffer from poorer electrochemical performance, due to clogging by the thick polymeric layer formed using standard electrolytes, than cells with thicker and hydrophilic separators.

  4. Proteomics of a fuzzy organelle: interphase chromatin

    Science.gov (United States)

    Kustatscher, Georg; Hégarat, Nadia; Wills, Karen L H; Furlan, Cristina; Bukowski-Wills, Jimi-Carlo; Hochegger, Helfrid; Rappsilber, Juri

    2014-01-01

    Chromatin proteins mediate replication, regulate expression, and ensure integrity of the genome. So far, a comprehensive inventory of interphase chromatin has not been determined. This is largely due to its heterogeneous and dynamic composition, which makes conclusive biochemical purification difficult, if not impossible. As a fuzzy organelle, it defies classical organellar proteomics and cannot be described by a single and ultimate list of protein components. Instead, we propose a new approach that provides a quantitative assessment of a protein's probability to function in chromatin. We integrate chromatin composition over a range of different biochemical and biological conditions. This resulted in interphase chromatin probabilities for 7635 human proteins, including 1840 previously uncharacterized proteins. We demonstrate the power of our large-scale data-driven annotation during the analysis of cyclin-dependent kinase (CDK) regulation in chromatin. Quantitative protein ontologies may provide a general alternative to list-based investigations of organelles and complement Gene Ontology. PMID:24534090

  5. Electrophoretic deposition of 9-YSZ solid electrolyte on Ni- YSZ composite; Estudos de deposicao eletroforetica de ceramicas de 9-YSZ sobre Ni-YSZ

    Energy Technology Data Exchange (ETDEWEB)

    Santos, F.S.; Yoshito, W.K.; Lazar, D.R.R.; Ussui, V., E-mail: vussui@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (CCTM/IPEN/CNEN-SP), Sao Paulo, SP (Brazil). Centro de Ciencia e Tecnologia de Materiais

    2010-07-01

    9-YSZ ceramic and Ni-YSZ metal/ceramic composite are the more commonly used materials for the fabrication of solid oxide fuel cell electrolyte and anode, respectively. The main challenges for these applications are the forming of both materials as superposed double thin layers. In the present work ceramic powder of 9- YSZ was synthesized by a coprecipitation technique and the Ni O-YSZ composite by a combustion technique. The later was formed by uniaxial pressing as cylindrical pellets of 15 mm diameter. Thin ceramic layers of 9-YSZ were deposited on composite pellets from a suspension with 10% solid content by an Electrophoretic Deposition technique. Applied voltage varied in the range of 30 to 200 V and deposition time from 15 to 90 seconds, evaluating the deposited mass, porosity on the interface and adhesion of layers. Resulted ceramics were characterized by X-ray diffraction and were observed in a scanning electron microscope. Results showed that deposited layers are thin ({approx}20{mu}m), dense and have good adhesion on the surface of composite substrate. (author)

  6. Synthesis of 8YSZ-LSGM Composite Thick Film Ceramics for Solid Electrolyte From Nanopowder Utilizing Local Zircon Prepared Using Sol Gel Process

    Science.gov (United States)

    Syarif, Dani Gustaman; Soepriyanto, Syoni; Ismunandar, Korda, Akhmad

    2010-10-01

    Thick film ceramics of 8% mol Y2O3 doped-ZrO2 (8YSZ)-La0.8Sr0.2Ga0.2Mg0.8O3 (LSGM) composite for solid electrolyte have been synthesized from nanopowder. Concentration of LSGM was 0 and 10% weight. A paste for the thick films was made from 8YSZ nanopowder prepared using sol gel method and LSGM powder prepared by solid state reaction. Precursors for the 8YSZ nanopowder preparation were ZrOCl2ṡ8H2O derived from local zircon as byproduct of Tin processing at Bangka Island using caustic fussion method, and Y(NO3)3. The thick films were produced by screen printing technique on alumina substrates. The films were sintered at 1500° C for 2 hours in air. X-ray diffraction (XRD) data showed that the nanopowder of 8YSZ was well produced with broad peaks. The particle size of the 8YSZ powder was about 12 nm as calculated using Debye Scherrer method. The thick films of 8YSZ and 8YSZ-LSGM (90:10 in weight %) composite could be produced, however, the films still contain voids. The ionic conductance of the YSZ-10LSGM films was smaller than that of the YSZ films.

  7. Structure and properties of solid polymer electrolyte based on chitosan and ZrO{sub 2} nanoparticle for lithium ion battery

    Energy Technology Data Exchange (ETDEWEB)

    Sudaryanto,, E-mail: dryanto@batan.go.id; Yulianti, Evi, E-mail: yulianti@batan.go.id [Center for Sains and Technology Advanced Materials – BATAN Kawasan Puspiptek Serpong, Tangerang Selatan, BantenV 15314 (Indonesia); Patimatuzzohrah, E-mail: pzohrah@yahoo.com [Department Of Physics, Mataram University, Jl. Majapahit 62, Mataram, NTB 83125 (Indonesia)

    2016-02-08

    In order to develop all solid lithium ion battery, study on the structure and properties of solid polymer electrolytes (SPE) based on chitosan has been done. The SPE were prepared by adding Zirconia (ZrO{sub 2}) nanoparticle and LiClO{sub 4} as lithium salt into the chitosan solution followed by casting method. Effect of the ZrO{sub 2} and salt concentration to the structure and properties of SPE were elaborated using several methods. The structure of the SPE cast film, were characterized mainly by using X-ray diffractometer (XRD). While the electrical properties of SPE were studied by electrochemical impedance spectrometer (EIS) and ion transference number measurement. XRD profiles show that the addition of ZrO{sub 2} and LiClO{sub 4} disrupts the crystality of chitosan. The decrease in sample crytalinity with the nanoparticle and salt addition may increase the molecular mobility result in the increasing sample conductivity and cathionic transference number as determined by EIS and ion transference number measurement, respectively. The highest ionic conductivity (3.58×10{sup −4} S cm{sup −1}) was obtained when 4 wt% of ZrO{sub 2} nanoparticle and 40 wt% of LiClO{sub 4} salt were added to the chitosan. The ion transference number with that composition was 0.55. It is high enough to be used as SPE for lithium ion battery.

  8. Neutron diffraction and TSDC on Ba1−xUxF2+2x solid electrolytes

    DEFF Research Database (Denmark)

    Ouwerkerk, M.; Andersen, N. H.; Veldkamp, F. F.

    1986-01-01

    The defect structure of fluorite-type Ba1−xUxF2+2x solid solutions, which exhibit fast fluoride ion conductivity, has been investigated by quasi-elastic diffuse neutron scattering (QDNS) experiments, and thermally stimulated depolarisation current (TSDC) measurements. A comparison with model...

  9. Lithium/organosulfur redox cell having protective solid electrolyte barrier formed on anode and method of mixing the same

    Energy Technology Data Exchange (ETDEWEB)

    DeJonghe, L.C.; Visco, S.J.; Liu, M.; Mailhe, C.C.

    1990-04-17

    This patent describes a solid lithium-organosulfur redox cell. It comprises: a solid lithium anode formed from a material selected from the class consisting of elemental lithium and one or more lithium base alloys comprising over 50 wt. % lithium or mixtures thereof; a liquid organosulfur cathode having the formula of (R(S){sub {ital Y}}){sub {ital N}} where y = 1 to 6, n = 2 to 20, and R is one or more different aliphatic or aromatic organic moieties having 1 to 20 carbon atoms, which may include one or more oxygen, sulfur, nitrogen, or fluorine atoms associated with the chain when R comprises an aliphatic chain. The linear chain may be linear or branched, saturated or unsaturated, and wherein either the aliphatic chain or the aromatic ring may have substituted groups thereon; and a barrier layer formed adjacent a surface of the solid lithium anode consisting of a reaction product of the solid lithium anode with the liquid organosulfur cathode.

  10. The effect of water-containing electrolyte on lithium-sulfur batteries

    Science.gov (United States)

    Wu, Heng-Liang; Haasch, Richard T.; Perdue, Brian R.; Apblett, Christopher A.; Gewirth, Andrew A.

    2017-11-01

    Dissolved polysulfides, formed during Li-S battery operation, freely migrate and react with both the Li anode and the sulfur cathode. These soluble polysulfides shuttle between the anode and cathode - the so-called shuttle effect - resulting in an infinite recharge process and poor Columbic efficiency. In this study, water present as an additive in the Li-S battery electrolyte is found to reduce the shuttle effect in Li-S batteries. Batteries where water content was below 50 ppm exhibited a substantial shuttle effect and low charge capacity. Alternatively, addition of 250 ppm water led to stable charge/discharge behavior with high Coulombic efficiency. XPS results show that H2O addition results in the formation of solid electrolyte interphase (SEI) film with more LiOH on Li anode which protects the Li anode from the polysulfides. Batteries cycled without water result in a SEI film with more Li2CO3 likely formed by direct contact between the Li metal and the solvent. Intermediate quantities of H2O in the electrolyte result in high cycle efficiency for the first few cycles which then rapidly decays. This suggests that H2O is consumed during battery cycling, likely by interaction with freshly exposed Li metal formed during Li deposition.

  11. Fluorine-donating electrolytes enable highly reversible 5-V-class Li metal batteries.

    Science.gov (United States)

    Suo, Liumin; Xue, Weijiang; Gobet, Mallory; Greenbaum, Steve G; Wang, Chao; Chen, Yuming; Yang, Wanlu; Li, Yangxing; Li, Ju

    2018-01-19

    Lithium metal has gravimetric capacity ∼10× that of graphite which incentivizes rechargeable Li metal batteries (RLMB) development. A key factor that limits practical use of RLMB is morphological instability of Li metal anode upon electrodeposition, reflected by the uncontrolled area growth of solid-electrolyte interphase that traps cyclable Li, quantified by the Coulombic inefficiency (CI). Here we show that CI decreases approximately exponentially with increasing donatable fluorine concentration of the electrolyte. By using up to 7 m of Li bis(fluorosulfonyl)imide in fluoroethylene carbonate, where both the solvent and the salt donate F, we can significantly suppress anode porosity and improve the Coulombic efficiency to 99.64%. The electrolyte demonstrates excellent compatibility with 5-V LiNi0.5Mn1.5O4 cathode and Al current collector beyond 5 V. As a result, an RLMB full cell with only 1.4× excess lithium as the anode was demonstrated to cycle above 130 times, at industrially significant loading of 1.83 mAh/cm2 and 0.36 C. This is attributed to the formation of a protective LiF nanolayer, which has a wide bandgap, high surface energy, and small Burgers vector, making it ductile at room temperature and less likely to rupture in electrodeposition.

  12. Interphase cytogenetics of workers exposed to benzene

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, L.; Wang, Yunxia; Venkatesh, P. [Univ. of California, Berkeley, CA (United States)] [and others

    1996-12-01

    Fluorescence in situ hybridization (FISH) is a powerful new technique that allows numerical chromosome aberrations (aneuploidy) to be detected in interphase cells. In previous studies, FISH has been used to demonstrate that the benzene metabolites hydroquinone and 1,2,4-benzenetriol induce aneuploidy of chromosomes 7 and 9 in cultures of human cells. In the present study, we used an interphase FISH procedure to perform cytogenetic analyses on the blood cells of 43 workers exposed to benzene (median=31 ppm, 8-hr time-weighted average) and 44 matched controls from Shanghai, China. High benzene exposure (>31 ppm, n=22) increased the hyperdiploid frequency of chromosome 9 (p<0.01), but lower exposure (<31 ppm, n=21) did not. Trisomy 9 was the major form of benzene-induced hyperdiploidy. The level of hyperdiploidy in exposed workers correlated with their urinary phenol level (r= 0.58, p < 0.0001), a measure of internal benzene close. A significant correlation was also found between hyperdiploicly and decreased absolute lymphocyte count, an indicator of benzene hematotoxicity, in the exposed group (r=-0.44, p=0.003) but not in controls (r=-0.09, P=0.58). These results show that high benzene exposure induces aneuploidy of chromosome 9 in nondiseased individuals, with trisomy being the most prevalent form. They further highlight the usefulness of interphase cytogenetics and FISH for the rapid and sensitive detection of aneuploidy in exposed human populations. 35 refs., 3 figs., 2 tabs.

  13. Using 2H labeling with neutron radiography for the study of solid polymer electrolyte water transport properties.

    Science.gov (United States)

    Boillat, P; Oberholzer, P; Seyfang, B C; Kästner, A; Perego, R; Scherer, G G; Lehmann, E H; Wokaun, A

    2011-06-15

    A method combining (2)H labeling of different sources of H atoms (hydrogen, water vapor) with neutron imaging for the analysis of transport parameters in the bulk and at the interfaces of Nafion polymer electrolyte membranes is proposed. The use of different isotope compositions in the steady state allows evaluation of the relation between bulk and interface transport parameters, but relies on literature data for evaluating absolute values. By using transients of isotope composition, absolute values of these parameters including the self-diffusion coefficient of H can be extracted, making this method an attractive alternative to self-diffusion measurements using nuclear magnetic resonance (NMR), allowing measurements in precisely controlled conditions in real fuel cell structures. First measurements were realized on samples with and without electrodes and we report values of the self-diffusion coefficient of the same order of magnitude as values measured using NMR, although with slightly higher numbers. In our particular case, lower interfacial exchange rates for water transport were observed for samples with an electrode.

  14. Rational design of efficient electrode–electrolyte interfaces for solid-state energy storage using ion soft landing

    Science.gov (United States)

    Prabhakaran, Venkateshkumar; Mehdi, B. Layla; Ditto, Jeffrey J.; Engelhard, Mark H.; Wang, Bingbing; Gunaratne, K. Don D.; Johnson, David C.; Browning, Nigel D.; Johnson, Grant E.; Laskin, Julia

    2016-01-01

    The rational design of improved electrode–electrolyte interfaces (EEI) for energy storage is critically dependent on a molecular-level understanding of ionic interactions and nanoscale phenomena. The presence of non-redox active species at EEI has been shown to strongly influence Faradaic efficiency and long-term operational stability during energy storage processes. Herein, we achieve substantially higher performance and long-term stability of EEI prepared with highly dispersed discrete redox-active cluster anions (50 ng of pure ∼0.75 nm size molybdenum polyoxometalate (POM) anions on 25 μg (∼0.2 wt%) carbon nanotube (CNT) electrodes) by complete elimination of strongly coordinating non-redox species through ion soft landing (SL). Electron microscopy provides atomically resolved images of a uniform distribution of individual POM species soft landed directly on complex technologically relevant CNT electrodes. In this context, SL is established as a versatile approach for the controlled design of novel surfaces for both fundamental and applied research in energy storage. PMID:27097686

  15. Lithium/organosulfur redox cell having protective solid electrolyte barrier formed on anode and method of making same

    Energy Technology Data Exchange (ETDEWEB)

    De Jonghe, Lutgard C. (Berkeley, CA); Visco, Steven J. (Berkeley, CA); Liu, Meilin (Albany, CA); Mailhe, Catherine C. (Vevey, CH)

    1990-01-01

    A lithium/organosulfur redox cell is disclosed which comprises a solid lium anode, a liquid organosulfur cathode, and a barrier layer formed adjacent a surface of the solid lithium anode facing the liquid organosulfur cathode consisting of a reaction product of the lithium anode with the organosulfur cathode. The organosulfur cathode comprises a material having the formula (R(S).sub.y).sub.N where y=1 to 6, n=2 to 20 and R is one or more different aliphatic or aromatic organic moieties having 1 to 20 carbon atoms, which may include one or more oxygen, sulfur, nitrogen, or fluorine atoms associated with the chain when R comprises an aliphatic chain, wherein the linear chain may be linear or branched, saturated or unsaturated, and wherein either the aliphatic chain or the aromatic ring may have substituted groups thereon.

  16. Lithium/organosulfur redox cell having protective solid electrolyte barrier formed on anode and method of making same

    Energy Technology Data Exchange (ETDEWEB)

    DeJonghe, L.C.; Visco, S.J.; Liu, M.; Mailhe, C.C.

    1990-04-17

    This patent describes a lithium/organosulfur redox cell. It comprises: a solid lithium anode, a liquid organosulfur cathode, and a barrier layer formed adjacent a surface of the solid lithium anode facing the liquid organosulfur cathode consisting of a reaction product of the lithium anode with the organosulfur cathode. The organosulfur cathode comprises a material having the formula (R(S){sub {ital y}}){sub {ital N}} where y = 1 to 6, n = 2 to 20 and R is one or more different aliphatic or aromatic organic moieties having 1 to 20 carbon atoms, which may include one or more oxygen, sulfur, nitrogen, or fluorine atoms associated with he chain when R comprises an aliphatic chain, wherein the linear chain may be linear or branched, saturated or unsaturated, and wherein either the aliphatic chain or the aromatic ring may have substituted groups thereon.

  17. Spin coating of electrolytes

    Science.gov (United States)

    Stetter, Joseph R.; Maclay, G. Jordan

    1989-01-01

    Methods for spin coating electrolytic materials onto substrates are disclosed. More particularly, methods for depositing solid coatings of ion-conducting material onto planar substrates and onto electrodes are disclosed. These spin coating methods are employed to fabricate electrochemical sensors for use in measuring, detecting and quantifying gases and liquids.

  18. Li-Ion Cells Employing Electrolytes With Methyl Propionate and Ethyl Butyrate Co-Solvents

    Science.gov (United States)

    Smart, Marshall C.; Bugga, Ratnakumar V.

    2011-01-01

    temperature range in MCMB-LiNiCoAlO2 and Li4Ti5O12-LiNi-CoAlO2 prototype cells. These electrolytes have enabled high rate performance at low temperature (i.e., up to 2.0C rates at -50 C and 5.0C rates at -40 C), and good cycling performance over a wide temperature range (i.e., from -40 to +70 C). Current efforts are focused upon improving the high temperature resilience of the methyl propionatebased system through the use of electrolyte additives, which are envisioned to improve the nature of the solid electrolyte interphase (SEI) layers.

  19. Efficient Electrolytes for Lithium–Sulfur Batteries

    OpenAIRE

    Natarajan eAngulakshmi; Arul Manuel Stephan

    2015-01-01

    This review article mainly encompasses on the state-of-the-art electrolytes for lithium–sulfur batteries. Different strategies have been employed to address the issues of lithium–sulfur batteries across the world. One among them is identification of electrolytes and optimization of their properties for the applications in lithium–sulfur batteries. The electrolytes for lithium–sulfur batteries are broadly classified as (i) non-aqueous liquid electrolytes, (ii) ionic liquids, (iii) solid polyme...

  20. Polymer Electrolytes for Lithium/Sulfur Batteries

    OpenAIRE

    The Nam Long Doan; Denise Gosselink; Yongguang Zhang; Mikhail Sadhu; Ho-Jae Cheang; Pu Chen; Yan Zhao

    2012-01-01

    This review evaluates the characteristics and advantages of employing polymer electrolytes in lithium/sulfur (Li/S) batteries. The main highlights of this study constitute detailed information on the advanced developments for solid polymer electrolytes and gel polymer electrolytes, used in the lithium/sulfur battery. This includes an in-depth analysis conducted on the preparation and electrochemical characteristics of the Li/S batteries based on these polymer electrolytes.

  1. Polymer Electrolytes for Lithium/Sulfur Batteries

    Directory of Open Access Journals (Sweden)

    The Nam Long Doan

    2012-08-01

    Full Text Available This review evaluates the characteristics and advantages of employing polymer electrolytes in lithium/sulfur (Li/S batteries. The main highlights of this study constitute detailed information on the advanced developments for solid polymer electrolytes and gel polymer electrolytes, used in the lithium/sulfur battery. This includes an in-depth analysis conducted on the preparation and electrochemical characteristics of the Li/S batteries based on these polymer electrolytes.

  2. Polymer Electrolytes for Lithium/Sulfur Batteries

    Science.gov (United States)

    Zhao, Yan; Zhang, Yongguang; Gosselink, Denise; Doan, The Nam Long; Sadhu, Mikhail; Cheang, Ho-Jae; Chen, Pu

    2012-01-01

    This review evaluates the characteristics and advantages of employing polymer electrolytes in lithium/sulfur (Li/S) batteries. The main highlights of this study constitute detailed information on the advanced developments for solid polymer electrolytes and gel polymer electrolytes, used in the lithium/sulfur battery. This includes an in-depth analysis conducted on the preparation and electrochemical characteristics of the Li/S batteries based on these polymer electrolytes. PMID:24958296

  3. Achievement report for fiscal 1997 on research and development of solid electrolyte fuel cells; Kotai denkaishitsugata nenryo denchi no kenkyu kaihatsu 1997 nendo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-07-01

    This paper describes the achievements in fiscal 1997 on research and development of solid electrolyte fuel cells. Fuji Electric has demonstrated possibilities of film type cells of predominantly metallic flat plate supporting type of a large-area cell lamination system, and seal-less stack structure. Sanyo Electric has discussed making thinner the composite cell lamination type anode, optimization in sintering temperature, and sealing materials. The Fine Ceramic Center has performed a 1,000-hour test on an La(Sr) MnO{sub 3}-YSZ electrode, in which A-site defect amount was decreased to 0.1-0.02 to stabilize micro-structure air electrodes for an extended period of time. Fujikura has discussed functional materials for high dispersion and slanting in a fuel electrode Ni/YSZ. Mitsubishi Heavy Industries has fabricated MgO-based fuel electrodes on a trial basis, and performed internal reformation and power generation tests by using full-size stacks. Murata Manufacturing Company has verified long-term power generation properties and stability of a three-layered co-sintered film of flat plate type. Mitsui Shipbuilding has reached a near final conclusion on the basic structure of gas separator cells. The Central Electric Power Research Institute has completed a conceptual design on a 300-MW class composite power generation system in which SOFC and gas turbines are combined. The Electric Power Development Company has discussed problems in SOFC composite power generation development using coal gasified fuel. (NEDO)

  4. Pyrolysis result of polyethylene waste as fuel for solid oxide fuel cell with samarium doped-ceria (SDC)-carbonate as electrolyte

    Science.gov (United States)

    Syahputra, R. J. E.; Rahmawati, F.; Prameswari, A. P.; Saktian, R.

    2017-02-01

    In this research, the result of pyrolysis on polyethylene was used as fuel for a solid oxide fuel cell (SOFC). The pyrolysis result is a liquid which consists of hydrocarbon chains. According to GC-MS analysis, the hydrocarbons mainly consist of C7 to C20 hydrocarbon chain. Then, the liquid was applied to a single cell of NSDC-L | NSDC | NSDC-L. NSDC is a composite SDC (samarium doped-ceria) with sodium carbonate. Meanwhile, NSDC-L is a composite of NSDC with LiNiCuO (LNC). NSDC and LNC were analyzed by X-ray diffraction to understand their crystal structure. The result shows that presence of carbonate did not change the crystal structure of SDC. SEM EDX analysis for fuel cell before and after being loaded with polyethylene oil to get information of element diffusion to the electrolyte. Meanwhile, the conductivity properties were investigated through impedance measurement. The presence of carbonate even increases the electrical conductivity. The single cell test with the pyrolysis result of polyethylene at 300 - 600 °C, found that the highest power density is at 600 °C with the maximum power density of 0.14 mW/cm2 and open circuit voltage of 0.4 Volt. Elemental analysis at three point spots of single cell NDSC-L |NSDC|NSDC-L found that a migration of ions was occurred during fuel operation at 300 - 600 °C.

  5. Binder for solid electrolyte fuel cell stack and its production method; Kotai denkaishitsugata nenryo denchi sutakku no setsugozai oyobi sono seizo hoho

    Energy Technology Data Exchange (ETDEWEB)

    Murata, K.

    1994-08-12

    In general, the interconnector of the solid electrolyte fuel cell stack consists of such materials as lanthanum chromite system ceramics, heat resistant alloy, and nickel felt. A poor deformability of lanthanum chromite system ceramics at a temperature to joint the electrode membrane of unit cell gives rise to an insufficient contact area, resulting in a large electric resistance. This invention solves the problem. The bonding of the unit cell electrode membrane with the interconnector is done by inserting the bonding material which has a high deformability at the bonding temperature as well as a high electric conductivity into their interface, resulting in being able to keep a wide contact area so as to reduce the electric contact resistance. The bonding material is composed of porous ceramics with porosity of 30 - 80% consisting of nickel thermit such as Ni-ZrO2, Ni-A12O3, and Ni-A12O3-MgO plus 0.1 - 10 wt% SiO2. 2 figs., 1 tab.

  6. Stabilized γ-BIMNVOX solid electrolyte: Ethylene glycol–citrate sol–gel synthesis, microwave-assisted calcination, and structural and electrical characterization

    Energy Technology Data Exchange (ETDEWEB)

    Al-Areqi, Niyazi A.S., E-mail: niyazi.alareqi@gmail.com [Department of Chemistry, Faculty of Applied Science, Taiz University, Taiz, Republic of Yemen (Yemen); Beg, Saba [Department of Chemistry, Aligarh Muslim University, Aligarh 202002 (India); Al-Alas, Ahlam [Department of Chemistry, Faculty of Applied Science, Taiz University, Taiz, Republic of Yemen (Yemen); Hafeez, Shehla [Department of Chemistry, Aligarh Muslim University, Aligarh 202002 (India)

    2013-12-25

    Highlights: •γ-BIMNVOX was synthesized by ethylene glycol–citrate sol–gel route. •γ-BIMNVOX crystallizes by 25-min microwave-assisted calcination. •Smaller particle sizes for microwave calcined BIMNVOX samples. •Best oxide-ion performance for microwave calcined BIMNVOX samples. -- Abstract: Samples of γ-BIMNVOX (Bi{sub 2}V{sub 1−x}Mn{sub x}O{sub 5.5−x/2}; 0.13 ⩽ x ⩽ 0.20) system were synthesized by an ethylene glycol–citrate sol–gel route. The resulting xerogels were then calcined by the microwave heating using a modified domestic microwave oven operated at 2.45 GHz. Microwave-assisted calcination samples in comparison with other conventionally calcined samples were characterized in terms of phase crystallization, stabilization and particle size using simultaneous thermogravimetric–differential thermal analysis (TG–DTA), X-ray powder diffraction (XRPD) and scanning electron microscopy (SEM). The AC impedance spectroscopy was employed for electrical characterization. It was found that the microwave-assisted calcination route successfully produces better crystalline stabilized γ-BIMNVOX samples with appreciably small average particle sizes after only 25 min of microwave heating. The electrical properties of microwave calcined γ-BIMNVOX system make it an advanced low-temperature solid electrolyte suitable for use in oxide-ion based electrochemical applications.

  7. Newly developed EMF cell with zirconia solid electrolyte for measurement of low oxygen potentials in liquid Cu-Cr and Cu-Zr alloys

    Directory of Open Access Journals (Sweden)

    Katayama I.

    2012-01-01

    Full Text Available In order to measure the very low oxygen potential by use of stabilized zirconia solid electrolyte emf method, a new cell construction was devised. The idea was based on Janke but a zirconia rod was used instead of the zirconia crucible which contacts liquid alloy electrode. The cell was used for determination of the oxygen potentials in liquid dilute Cu-Cr and Cu-Zr alloys. The reference electrode was Cr,Cr2O3. Emf measurements were performed in the temperature range of 1400-1580K and composition range of 0.198-3.10at%Cr-Cu alloys, and 1380-1465K, 0.085-0.761at%Zr-Cu alloys. The composition of liquid alloys were determined by picking up from the liquid alloys and ICP analysis. By use of the newly devised cell construction in this study, stable emf values were obtained at each temperature and alloy composition. Emf values were corrected by using the parameter for electronic contribution of the YSZ. Activity of Cr obeys Henry’s law and activity coefficient at infinitely dilute alloys of Cr in Cu-Cr alloys are: lng0 Cr =(3.80 at 1423K, (3.57 at 1473K, (3.38 at 1523K and (3.20 at 1573K. At 1423 K activity coefficient of Zr at infinitely diluted alloy is lnγo Zr = -4.0.

  8. Influence of Indium-Tin Oxide Additive on the Sintering Process and Conductivity of Na3Zr2Si2PO12 Solid Electrolyte

    Science.gov (United States)

    Chen, Dan; Luo, Fa; Gao, Lu; Zhou, Wancheng; Zhu, Dongmei

    2017-11-01

    Because of the poor sintering ability and low phase purity limit in the application of a Na3Zr2Si2PO12 solid electrolyte, it is important to find an effective way to obtain a pure and dense Na3Zr2Si2PO12 ceramic at reduced temperature. In this study, high conductive indium-tin oxide (ITO) was innovatively used as the sintering additive to improve the purity and density of the Na3Zr2Si2PO12 ceramic. The influence of ITO additive on density, phase, microstructure and conductivity of the Na3Zr2Si2PO12 ceramic was investigated. Archimedes method, x-ray diffraction, scanning electron microcopy and complex impedance spectroscopy were used as experimental techniques to evaluate the effect of the additive. The results show that the ITO sintering additive increases not only the purity and density but also the conductivity of the Na3Zr2Si2PO12 ceramic. The Na3Zr2Si2PO12 ceramic with 3 wt.% ITO additive sintered at 1150°C for 4 h possesses a high density of 3.15 g/cm3 and good conductivity of (3.95 ± 0.12) × 10-4 S/cm.

  9. Microwave-assisted reactive sintering and lithium ion conductivity of Li1.3Al0.3Ti1.7(PO4)3 solid electrolyte

    Science.gov (United States)

    Hallopeau, Leopold; Bregiroux, Damien; Rousse, Gwenaëlle; Portehault, David; Stevens, Philippe; Toussaint, Gwenaëlle; Laberty-Robert, Christel

    2018-02-01

    Li1.3Al0.3Ti1.7(PO4)3 (LATP) materials are made of a three-dimensional framework of TiO6 octahedra and PO4 tetrahedra, which provides several positions for Li+ ions. The resulting high ionic conductivity is promising to yield electrolytes for all-solid-state Li-ion batteries. In order to elaborate dense ceramics, conventional sintering methods often use high temperature (≥1000 °C) with long dwelling times (several hours) to achieve high relative density (∼90%). In this work, an innovative synthesis and processing approach is proposed. A fast and easy processing technique called microwave-assisted reactive sintering is used to both synthesize and sinter LATP ceramics with suitable properties in one single step. Pure and crystalline LATP ceramics can be achieved in only 10 min at 890 °C starting from amorphous, compacted LATP's precursors powders. Despite a relative density of 88%, the ionic conductivity measured at ambient temperature (3.15 × 10-4 S cm-1) is among the best reported so far. The study of the activation energy for Li+ conduction confirms the high quality of the ceramic (purity and crystallinity) achieved by using this new approach, thus emphasizing its interest for making ion-conducting ceramics in a simple and fast way.

  10. Electrolytes and Interphasial Chemistry in Li Ion Devices

    Directory of Open Access Journals (Sweden)

    Kang Xu

    2010-01-01

    Full Text Available Since its appearance in 1991, the Li ion battery has been the major power source driving the rapid digitalization of our daily life; however, much of the processes and mechanisms underpinning this newest battery chemistry remains poorly understood. As in any electrochemical device, the major challenge comes from the electrolyte/electrode interfaces, where the discontinuity in charge distribution and extreme disequality in electric forces induce diversified processes that eventually determine the kinetics of Li+ intercalation chemistry. This article will summarize the most recent efforts on the fundamental understanding of the interphases in Li ion devices. Emphasis will be placed on the formation chemistry of the so-called “SEI” on graphitic anode, the effect of solvation sheath structure of Li+ on the intercalation energy barrier, and the feasibility of tailoring a desired interphase. Biologically inspired approaches to an ideal interphase will also be briefly discussed.

  11. All-solid-state lithium batteries – The Mg2FeH6-electrode LiBH4-electrolyte system

    DEFF Research Database (Denmark)

    Huen, Priscilla; Ravnsbæk, Dorthe B.

    2018-01-01

    , respectively, compared to the conventional liquid-electrolyte battery. Through investigations of the conversion reactions of Mg2FeH6, formation of MgH2 as intermediate in the conversion to Mg is discovered the first time. In addition, the effect of mixing procedure for the electrode-electrolyte composite...

  12. Interphase chromosome-specific multicolor banding (ICS-MCB): a new tool for analysis of interphase chromosomes in their integrity.

    Science.gov (United States)

    Iourov, Ivan Y; Liehr, Thomas; Vorsanova, Svetlana G; Yurov, Yuri B

    2007-10-01

    Biomedical research of interphase chromosomes in their integrity is hindered by technical limitations. We introduce a technology using microdissection-based engineering of DNA probes and fluorescence multicolor chromosome banding that allows studying interphase chromosome organization, numbers and rearrangements in somatic cells.

  13. Carbon Nanotube-CoF2 Multifunctional Cathode for Lithium Ion Batteries: Effect of Electrolyte on Cycle Stability.

    Science.gov (United States)

    Wang, Xinran; Gu, Wentian; Lee, Jung Tae; Nitta, Naoki; Benson, Jim; Magasinski, Alexandre; Schauer, Mark W; Yushin, Gleb

    2015-10-01

    Transition metal fluorides (MFx ) offer remarkably high theoretical energy density. However, the low cycling stability, low electrical and ionic conductivity of metal fluorides have severely limited their applications as conversion-type cathode materials for lithium ion batteries. Here, a scalable and low-cost strategy is reported on the fabrication of multifunctional cobalt fluoride/carbon nanotube nonwoven fabric nanocomposite, which demonstrates a combination of high capacity (near-theoretical, 550mAhgCoF2-1) and excellent mechanical properties. Its strength and modulus of toughness exceed that of many aluminum alloys, cast iron, and other structural materials, fulfilling the use of MFx -based materials in batteries with load-bearing capabilities. In the course of this study, cathode dissolution in conventional electrolytes has been discovered as the main reason that leads to the rapid growth of the solid electrolyte interphase layer and attributes to rapid cell degradation. And such largely overlooked degradation mechanism is overcome by utilizing electrolyte comprising a fluorinated solvent, which forms a protective ionically conductive layer on the cathode and anode surfaces. With this approach, 93% capacity retention is achieved after 200 cycles at the current density of 100 mA g(-1) and over 50% after 10 000 cycles at the current density of 1000 mA g(-1) . © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. High Lithium Storage Capacity and Long Cycling Life Fe3S4 Anodes with Reversible Solid Electrolyte Interface Films and Sandwiched Reduced Graphene Oxide Shells.

    Science.gov (United States)

    Zhang, Yu-Jiao; Qu, Jin; Hao, Shu-Meng; Chang, Wei; Ji, Qiu-Yu; Yu, Zhong-Zhen

    2017-11-21

    Increasing demands for lithium-ion batteries (LIBs) with high energy density and high power density require highly reversible electrochemical reactions to enhance the cyclability and capacities of electrodes. As the reversible formation/decomposition of the solid electrolyte interface (SEI) film during the lithiation/delithiation process of Fe3S4 could bring about a higher capacity than its theoretical value, in the present work, synthesized Fe3S4 nanoparticles are sandwich-wrapped with reduced graphene oxide (RGO) to fabricate highly reversible and long cycling life anode materials for high-performance LIBs. The micron-sized long slit between sandwiched RGO sheets effectively prevents the aggregation of intermediate phases during the discharge/charge process and thus increases cycling capacity because of the reversible formation/decomposition of the SEI film driven by Fe nanoparticles. Furthermore, the RGO sheets interconnect with each other by a face-to-face mode to construct a more efficiently conductive network, and the maximum interfacial oxygen bridge bonds benefit the fast electron hopping from RGO to Fe3S4, improving the depth of the electrochemical reactions and facilitating the highly reversible lithiation/delithiation of Fe3S4. Thus, the resultant Fe3S4/RGO hybrid shows a highly reversible charge capacity of 1324 mA h g(-1) over 275 cycles at a current density of 100 mA g(-1), even retains 480 mA h g(-1) over 500 cycles at 1000 mA g(-1), which are much higher than reported values.

  15. Intergranular and inter-phased boundaries in the materials; Joints intergranulaires et interphases dans les materiaux

    Energy Technology Data Exchange (ETDEWEB)

    Aslanides, A. [Electricite de France, Dept. CIMA, 77 - Moret sur Loing (France); Backhaus-Ricoult, M. [Centre d' Etudes de Chimie metallurgique, 94 - Vitry-sur-Seine (France); Bayle-Guillemaud, P. [CEA Grenoble, Dept. de Recherche Fondamentale sur la Matiere Condensee, 38 (France)] [and others

    2000-07-01

    This document collects the abstracts of the talks presented during the colloquium J2IM on the intergranular and inter-phased boundaries in the materials. Around the themes of the interfaces behaviour and grain boundaries defects in materials, these days dealt with the microstructure behaviour in many domains such as the interfaces in batteries, the irradiation damages and the special case of the fuel-cladding interactions, the stressed interfaces, the alumina or silicon carbides substrates. (A.L.B.)

  16. Highly effective Ir(x)Sn(1-x)O2 electrocatalysts for oxygen evolution reaction in the solid polymer electrolyte water electrolyser.

    Science.gov (United States)

    Li, Guangfu; Yu, Hongmei; Wang, Xunying; Sun, Shucheng; Li, Yongkun; Shao, Zhigang; Yi, Baolian

    2013-02-28

    We developed an advanced surfactant-assistant method for the Ir(x)Sn(1-x)O(2) (0 < x ≤ 1) nanoparticle (NP) preparation, and examined the OER performances by a series of half-cell and full-cell tests. In contrast to the commercial Ir black, the collective data confirmed the outstanding activity and stability of the fabricated Ir(x)Sn(1-x)O(2) (x = 1, 0.67 and 0.52) NPs, which could be ascribed to the amorphous structure, good dispersion, high pore volume, solid-solution state and Ir-rich surface for bi-metal oxides, and relatively large size (10-11 nm), while Ir(0.31)Sn(0.69) exhibited poor electro-catalytic activity because of the separated two phases, a SnO(2)-rich phase and an IrO(2)-rich phase. Furthermore, compared with highly active IrO(2), the improved durability, precious-metal Ir utilization efficiency and correspondingly reduced Ir loading were realized by the addition of Sn component. When the Ir(0.52)Sn(0.48)O(2) cell operated at 80 °C using Nafion® 115 membrane and less than 0.8 mg cm(-2) of the noble-metal Ir loading, the cell voltages we achieved were 1.631 V at 1000 mA cm(-2), and 1.821 V at 2000 mA cm(-2). The IR-free voltage at the studied current density was very close to the onset voltage of oxygen evolution. The only 50 μV h(-1) of voltage increased for the 500 h durability test at 500 mA cm(-2). In fact, these results are exceptional compared to the performances for OER in SPEWE cells known so far. This work highlights the potential of using highly active and stable IrO(2)-SnO(2) amorphous NPs to enhance the electrolysis efficiency, reduce the noble-metal Ir loading and thus the cost of hydrogen production from the solid polymer electrolyte water electrolysis.

  17. Chromosome Dynamics in the Yeast Interphase Nucleus

    Science.gov (United States)

    Heun, Patrick; Laroche, Thierry; Shimada, Kenji; Furrer, Patrick; Gasser, Susan M.

    2001-12-01

    Little is known about the dynamics of chromosomes in interphase nuclei. By tagging four chromosomal regions with a green fluorescent protein fusion to lac repressor, we monitored the movement and subnuclear position of specific sites in the yeast genome, sampling at short time intervals. We found that early and late origins of replication are highly mobile in G1 phase, frequently moving at or faster than 0.5 micrometers/10 seconds, in an energy-dependent fashion. The rapid diffusive movement of chromatin detected in G1 becomes constrained in S phase through a mechanism dependent on active DNA replication. In contrast, telomeres and centromeres provide replication-independent constraint on chromatin movement in both G1 and S phases.

  18. Electrolyte decomposition on Li-metal surfaces from first-principles theory

    Science.gov (United States)

    Ebadi, Mahsa; Brandell, Daniel; Araujo, C. Moyses

    2016-11-01

    An important feature in Li batteries is the formation of a solid electrolyte interphase (SEI) on the surface of the anode. This film can have a profound effect on the stability and the performance of the device. In this work, we have employed density functional theory combined with implicit solvation models to study the inner layer of SEI formation from the reduction of common organic carbonate electrolyte solvents (ethylene carbonate, propylene carbonate, dimethyl carbonate, and diethyl carbonate) on a Li metal anode surface. Their stability and electronic structure on the Li surface have been investigated. It is found that the CO producing route is energetically more favorable for ethylene and propylene carbonate decomposition. For the two linear solvents, dimethyl and diethyl carbonates, no significant differences are observed between the two considered reduction pathways. Bader charge analyses indicate that 2 e- reductions take place in the decomposition of all studied solvents. The density of states calculations demonstrate correlations between the degrees of hybridization between the oxygen of adsorbed solvents and the upper Li atoms on the surface with the trend of the solvent adsorption energies.

  19. Comprehensive Insights into the Reactivity of Electrolytes Based on Sodium Ions.

    Science.gov (United States)

    Eshetu, Gebrekidan Gebresilassie; Grugeon, Sylvie; Kim, Huikyong; Jeong, Sangsik; Wu, Liming; Gachot, Gregory; Laruelle, Stephane; Armand, Michel; Passerini, Stefano

    2016-03-08

    We report a systematic investigation of Na-based electrolytes that comprise various NaX [X=hexafluorophosphate (PF6 ), perchlorate (ClO4 ), bis(trifluoromethanesulfonyl)imide (TFSI), fluorosulfonyl-(trifluoromethanesulfonyl)imide (FTFSI), and bis(fluorosulfonyl)imide (FSI)] salts and solvent mixtures [ethylene carbonate (EC)/dimethyl carbonate (DMC), EC/diethyl carbonate (DEC), and EC/propylene carbonate (PC)] with respect to the Al current collector stability, formation of soluble degradation compounds, reactivity towards sodiated hard carbon (Nax -HC), and solid-electrolyte interphase (SEI) layer formation. Cyclic voltammetry demonstrates that the stability of Al is highly influenced by the nature of the anions, solvents, and additives. GC-MS analysis reveals that the formation of SEI telltales depends on the nature of the linear alkyl carbonates and the battery chemistry (Li(+) vs. Na(+) ). FTIR spectroscopy shows that double alkyl carbonates are the main components of the SEI layer on Nax -HC. In the presence of Na salts, EC/DMC and EC/DEC presented a higher reactivity towards Nax -HC than EC/PC. For a fixed solvent mixture, the onset temperature follows the sequence NaClO4

  20. Cytoskeletal dynamics in interphase, mitosis and cytokinesis analysed through Agrobacterium-mediated transient transformation of tobacco BY-2 cells.

    Science.gov (United States)

    Buschmann, H; Green, P; Sambade, A; Doonan, J H; Lloyd, C W

    2011-04-01

    Transient transformation with Agrobacterium is a widespread tool allowing rapid expression analyses in plants. However, the available methods generate expression in interphase and do not allow the routine analysis of dividing cells. Here, we present a transient transformation method (termed 'TAMBY2') to enable cell biological studies in interphase and cell division. Agrobacterium-mediated transient gene expression in tobacco BY-2 was analysed by Western blotting and quantitative fluorescence microscopy. Time-lapse microscopy of cytoskeletal markers was employed to monitor cell division. Double-labelling in interphase and mitosis enabled localization studies. We found that the transient transformation efficiency was highest when BY-2/Agrobacterium co-cultivation was performed on solid medium. Transformants produced in this way divided at high frequency. We demonstrated the utility of the method by defining the behaviour of a previously uncharacterized microtubule motor, KinG, throughout the cell cycle. Our analyses demonstrated that TAMBY2 provides a flexible tool for the transient transformation of BY-2 with Agrobacterium. Fluorescence double-labelling showed that KinG localizes to microtubules and to F-actin. In interphase, KinG accumulates on microtubule lagging ends, suggesting a minus-end-directed function in vivo. Time-lapse studies of cell division showed that GFP-KinG strongly labels preprophase band and phragmoplast, but not the metaphase spindle. © 2010 The Authors. New Phytologist © 2010 New Phytologist Trust.

  1. High Capacity, Superior Cyclic Performances in All-Solid-State Lithium-Ion Batteries Based on 78Li2S-22P2S5 Glass-Ceramic Electrolytes Prepared via Simple Heat Treatment.

    Science.gov (United States)

    Zhang, Yibo; Chen, Rujun; Liu, Ting; Shen, Yang; Lin, Yuanhua; Nan, Ce-Wen

    2017-08-30

    Highly Li-ion conductive 78Li2S-22P2S5 glass-ceramic electrolytes were prepared by simple heat treatment of the glass phase obtained via mechanical ball milling. A high ionic conductivity of ∼1.78 × 10(-3) S cm(-1) is achieved at room temperature and is attributed to the formation of a crystalline phase of high lithium-ion conduction. All-solid-state lithium-ion batteries based on these glass-ceramic electrolytes are assembled by using Li2S nanoparticles or low-cost commercially available FeS2 as active cathode materials and Li-In alloys as anode. A high discharge capacity of 535 mAh g(-1) is achieved after at least 50 cycles for the all-solid-state cells with Li2S as cathode materials, suggesting a rather high capacity retention of 97.4%. Even for the cells using low-cost FeS2 as cathode materials, same high discharge capacity of 560 mAh g(-1) is also achieved after at least 50 cycles. Moreover, the Coulombic efficiency remain at ∼99% for these all-solid-state cells during the charge-discharge cycles.

  2. Efficient Electrolytes for Lithium-Sulfur Batteries

    Directory of Open Access Journals (Sweden)

    Natarajan eAngulakshmi

    2015-05-01

    Full Text Available This review article mainly encompasses on the state-of-the-art electrolytes for lithium–sulfur batteries. Different strategies have been employed to address the issues of lithium-sulfur batteries across the world. One among them is identification of electrolytes and optimization of their properties for the applications in lithium-sulfur batteries. The electrolytes for lithium-sulfur batteries are broadly classified as (i non-aqueous liquid electrolytes, (ii ionic liquids, (iii solid polymer and (iv glass-ceramic electrolytes. This article presents the properties, advantages and limitations of each type of electrolytes. Also the importance of electrolyte additives on the electrochemical performance of Li-S cells is discussed.

  3. Flexible all-solid-state supercapacitors based on graphene/carbon black nanoparticle film electrodes and cross-linked poly(vinyl alcohol)-H2SO4 porous gel electrolytes

    Science.gov (United States)

    Fei, Haojie; Yang, Chongyang; Bao, Hua; Wang, Gengchao

    2014-11-01

    Flexible all-solid-state supercapacitors (SCs) are fabricated using graphene/carbon black nanoparticle (GCB) film electrodes and cross-linked poly(vinyl alcohol)-H2SO4 porous gel electrolytes (gPVAP-H2SO4). The GCB composite films, with carbon black (CB) nanoparticles uniformly distributed in the graphene nanosheets, greatly improve the active surface areas and ion transportation of pristine graphene film. The porous structure of as-prepared gPVAP-H2SO4 membrane improves the equilibrium swelling ratio in electrolyte and provides interconnected ion transport channels. The chemical crosslinking solves the fluidity problem of PVA-H2SO4 gel electrolyte at high temperature. As-fabricated GCB//gPVAP(20)-H2SO4//GCB flexible SC displays an increased specific capacitance (144.5 F g-1 at 0.5 A g-1) and a higher specific capacitance retention (67.9% from 0.2 to 4 A g-1). More importantly, the flexible SC possesses good electrochemical performance at high temperature (capacitance retention of 78.3% after 1000 cycles at 70 °C).

  4. Electrolyte Racers

    Science.gov (United States)

    Kellie, Shawn; Kellie, Tonya; Corbin-Tipton, Elizabeth

    2006-01-01

    A fast way to teach investigative skills in science is to tie them to NASCAR using Hot Wheels Formula Fuelers Race Cars. These inexpensive toy cars travel different distances based on the strength of the "electrolyte" (a substance that conducts electricity when dissolved in water) in their "fuel" tanks. Advertisements for these race cars urge kids…

  5. Interphase Chromosome Profiling: A Method for Conventional Banded Chromosome Analysis Using Interphase Nuclei.

    Science.gov (United States)

    Babu, Ramesh; Van Dyke, Daniel L; Dev, Vaithilingam G; Koduru, Prasad; Rao, Nagesh; Mitter, Navnit S; Liu, Mingya; Fuentes, Ernesto; Fuentes, Sarah; Papa, Stephen

    2017-10-05

    - Chromosome analysis on bone marrow or peripheral blood samples fails in a small proportion of attempts. A method that is more reliable, with similar or better resolution, would be a welcome addition to the armamentarium of the cytogenetics laboratory. - To develop a method similar to banded metaphase chromosome analysis that relies only on interphase nuclei. - To label multiple targets in an equidistant fashion along the entire length of each chromosome, including landmark subtelomere and centromere regions. Each label so generated by using cloned bacterial artificial chromosome probes is molecularly distinct with unique spectral characteristics, so the number and position of the labels can be tracked to identify chromosome abnormalities. - Interphase chromosome profiling (ICP) demonstrated results similar to conventional chromosome analysis and fluorescence in situ hybridization in 55 previously studied cases and obtained useful ICP chromosome analysis results on another 29 cases in which conventional methods failed. - ICP is a new and powerful method to karyotype peripheral blood and bone marrow aspirate preparations without reliance on metaphase chromosome preparations. It will be of particular value for cases with a failed conventional analysis or when a fast turnaround time is required.

  6. Fluorine-ion conductivity of different technological forms of solid electrolytes R 1- y M y F3- y (LaF3 Type ) ( M = Ca, Sr, Ba; R Are Rare Earth Elements)

    Science.gov (United States)

    Sorokin, N. I.; Sobolev, B. P.

    2016-05-01

    We have investigated the conductivity of some representatives of different technological forms of fluoride-conducting solid electrolytes R 1- y M y F3- y ( M = Ca, Sr, Ba; R are rare earth elements) with an LaF3 structure: single crystals, cold- and hot-pressing ceramics based on a charge prepared in different ways (mechanochemical synthesis, solid-phase synthesis, and fragmentation of single crystals), polycrystalline alloys, etc. It is shown (by impedance spectroscopy), that different technological forms of identical chemical composition ( R, M, y) exhibit different electrical characteristics. The maximum conductivity is observed for the single-crystal form of R 1- y M y F3- y tysonite phases, which provides (in contrast to other technological forms) the formation of true volume ion-conducting characteristics.

  7. Preparation of NASICON-Type Nanosized Solid Electrolyte Li1.4Al0.4Ti1.6(PO4)3 by Evaporation-Induced Self-Assembly for Lithium-Ion Battery.

    Science.gov (United States)

    Liu, Xingang; Fu, Ju; Zhang, Chuhong

    2016-12-01

    A simple and practicable evaporation-induced self-assembly (EISA) method is introduced for the first time to prepare nanosized solid electrolyte Li1.4Al0.4Ti1.6(PO4)3 (LATP) for all-solid-state lithium-ion batteries. A pure Na+ super ion conductor (NASICON) phase is confirmed by X-ray diffraction (XRD) analysis, and its primary particle size is down to 70 nm by optimizing evaporation rate of the solvent. Excellent room temperature bulk and total lithium-ion conductivities of 2.09 × 10-3 S cm-1 and 3.63 × 10-4 S cm-1 are obtained, with an ion-hopping activation energy as low as 0.286 eV.

  8. Solid electrolyte membranes and the system to produce hydrogen from thermally decomposed water by solar energy; Taiyo energy riyo ni yoru mizu no chokusetsu netsubunkai kara no suiso seizoyo

    Energy Technology Data Exchange (ETDEWEB)

    Nigara, K.; Watanabe, K.; Kawamura, K.; Kawada, T.; Mizusaki, J.; Ishigame, M. [Tohoku University, Sendai (Japan). Research Institute for Scientific Measurements

    1996-10-27

    For conversion of solar heat to transportable energy, hydrogen production by direct thermal decomposition of water using concentrated high-temperature solar heat was studied. Water vapor is injected into the tubular target with high melting point and high oxygen permeability at high temperature while heating the target by concentrated solar heat over 2000K. Oxygen in decomposed gas is discharged through an oxygen permeable membrane to extract hydrogen. Solid electrolyte is used as one of the target materials. Oxygen gas in the high-oxygen partial pressure site changes into oxygen ion by accepting two electrons at the target surface, and returns to neutral oxygen gas in the low-oxygen partial pressure site by discharging two electrons at the surface after permeation through oxygen vacancy. In the case of n-type solid electrolyte, to obtain constant permeation of a large amount of oxygen, flow of a large amount of electrons is indispensable in the opposite direction to oxygen ion. Among [(ZrO2)(1-x)(CeO2)x](0.9)(CaO)(0.1), materials of 0.4-0.5 in x seems to be useful as the target material. 7 refs., 7 figs.

  9. Positively charged polysilsesquioxane/iodide lonic liquid as a quasi solid-state redox electrolyte for dye-sensitized photo electrochemical cells: infrared, 29 Si NMR, and electrical studies

    Directory of Open Access Journals (Sweden)

    2006-01-01

    Full Text Available A new sol-gel precursor based on 1-methyl-3-[3-(trimethoxy- λ 4 -silylpropyl]-1 H -imidazolium iodide (MTMSPI + I − was synthesized and investigated as a potential novel quasi solid-state ionic liquid redox electrolyte for dye-synthesized photoelectrochemical (DSPEC cells of the Graetzel type. MTMSPI + I − was hydrolyzed with acidified water and the reaction products of the sol-gel condensation reactions assessed with the help of 29 Si NMR and infrared spectroscopic techniques. Results of the time-dependent spectra analyses showed the formation of positively charged polyhedral cube-like silsesquioxane species that still contained a small amount of silanol end groups, which were removed after heating at 200 ° C . After cooling, the resulting material formed is a tough, yellowish, and transparent solid, which could be reheated again and used for assembling DSPEC cells. The addition of iodine increased the specific conductivity of the hydrolyzed and nonhydrolyzed MTMSPI + I − , which we attributed to the formation of triiodide ions contributed to the conductivity via the Grotthus mechanism. DSPEC cells based on a titania-dye system with MTMSPI + I − electrolyte containing iodine (0.1 M reached an overall efficiency between 3.3–3.7%.

  10. Low temperature pulsed laser deposition of garnet Li6.4La3Zr1.4Ta0.6O12 films as all solid-state lithium battery electrolytes

    Science.gov (United States)

    Saccoccio, Mattia; Yu, Jing; Lu, Ziheng; Kwok, Stephen C. T.; Wang, Jian; Yeung, Kan Kan; Yuen, Matthew M. F.; Ciucci, Francesco

    2017-10-01

    With its stability against Li and good ionic conductivity, Li7La3Zr2O12 (LLZO) has emerged as a promising electrolyte material for lithium-based solid-state batteries (SSBs). Thin layers of solid electrolyte are needed to enable the practical use of SSBs. We report the first deposition of Li-conductive crystalline Ta-doped LLZO thin films on MgO (100) substrates via pulsed laser deposition. Further, we investigate the impact of laser fluence, deposition temperature (in the 50 °C-700 °C range), and post-deposition annealing on the structural, compositional, and transport properties of the film. We analyze the structure of the deposited films via grazing incident X-ray diffraction, their morphology via scanning electron microscopy, and the composition via depth profiling X-ray photoelectron spectroscopy and time-of-flight secondary ion mass spectrometry. The Li ionic conductivity is investigated via electrochemical impedance spectroscopy. Contrary to previous reports for LLZO films, the crystalline Ta-doped films presents a pure cubic LLZO structure for deposition temperatures as low as 50 °C, with resulting conductivities not significantly influenced by the temperature deposition. Instead, the laser fluence has a major effect on the growth rate of the thin films.

  11. Drug delivery device including electrolytic pump

    KAUST Repository

    Foulds, Ian G.

    2016-03-31

    Systems and methods are provided for a drug delivery device and use of the device for drug delivery. In various aspects, the drug delivery device combines a “solid drug in reservoir” (SDR) system with an electrolytic pump. In various aspects an improved electrolytic pump is provided including, in particular, an improved electrolytic pump for use with a drug delivery device, for example an implantable drug delivery device. A catalytic reformer can be incorporated in a periodically pulsed electrolytic pump to provide stable pumping performance and reduced actuation cycle.

  12. Effects of aneuploidy on genome structure, expression, and interphase organization in Arabidopsis thaliana.

    Directory of Open Access Journals (Sweden)

    Bruno Huettel

    2008-10-01

    Full Text Available Aneuploidy refers to losses and/or gains of individual chromosomes from the normal chromosome set. The resulting gene dosage imbalance has a noticeable affect on the phenotype, as illustrated by aneuploid syndromes, including Down syndrome in humans, and by human solid tumor cells, which are highly aneuploid. Although the phenotypic manifestations of aneuploidy are usually apparent, information about the underlying alterations in structure, expression, and interphase organization of unbalanced chromosome sets is still sparse. Plants generally tolerate aneuploidy better than animals, and, through colchicine treatment and breeding strategies, it is possible to obtain inbred sibling plants with different numbers of chromosomes. This possibility, combined with the genetic and genomics tools available for Arabidopsis thaliana, provides a powerful means to assess systematically the molecular and cytological consequences of aberrant numbers of specific chromosomes. Here, we report on the generation of Arabidopsis plants in which chromosome 5 is present in triplicate. We compare the global transcript profiles of normal diploids and chromosome 5 trisomics, and assess genome integrity using array comparative genome hybridization. We use live cell imaging to determine the interphase 3D arrangement of transgene-encoded fluorescent tags on chromosome 5 in trisomic and triploid plants. The results indicate that trisomy 5 disrupts gene expression throughout the genome and supports the production and/or retention of truncated copies of chromosome 5. Although trisomy 5 does not grossly distort the interphase arrangement of fluorescent-tagged sites on chromosome 5, it may somewhat enhance associations between transgene alleles. Our analysis reveals the complex genomic changes that can occur in aneuploids and underscores the importance of using multiple experimental approaches to investigate how chromosome numerical changes condition abnormal phenotypes and

  13. Highly Stable Sr-Free Cobaltite-Based Perovskite Cathodes Directly Assembled on a Barrier-Layer-Free Y2 O3 -ZrO2 Electrolyte of Solid Oxide Fuel Cells.

    Science.gov (United States)

    Ai, Na; Li, Na; Rickard, William D A; Cheng, Yi; Chen, Kongfa; Jiang, San Ping

    2017-03-09

    Direct assembly is a newly developed technique in which a cobaltite-based perovskite (CBP) cathode can be directly applied to a barrier-layer-free Y2 O3 -ZrO2 (YSZ) electrolyte with no high-temperature pre-sintering steps. Solid oxide fuel cells (SOFCs) based on directly assembled CBPs such as La0.6 Sr0.4 Co0.2 Fe0.8 O3-δ show high performance initially but degrade rapidly under SOFC operation conditions at 750 °C owing to Sr segregation and accumulation at the electrode/electrolyte interface. Herein, the performance and interface of Sr-free CBPs such as LaCoO3-δ (LC) and Sm0.95 CoO3-δ (SmC) and their composite cathodes directly assembled on YSZ electrolyte was studied systematically. The LC electrode underwent performance degradation, most likely owing to cation demixing and accumulation of La on the YSZ electrolyte under polarization at 500 mA cm-2 and 750 °C. However, the performance and stability of LC electrodes could be substantially enhanced by the formation of LC-gadolinium-doped ceria (GDC) composite cathodes. Replacement of La by Sm increased the cell stability, and doping of 5 % Pd to form Sm0.95 Co0.95 Pd0.05 O3-δ (SmCPd) significantly improved the electrode activity. An anode-supported YSZ-electrolyte cell with a directly assembled SmCPd-GDC composite electrode exhibited a peak power density of 1.4 W cm-2 at 750 °C, and an excellent stability at 750 °C for over 240 h. The higher stability of SmC as compared to that of LC is most likely a result of the lower reactivity of SmC with YSZ. This study demonstrates the new opportunities in the design and development of intermediate-temperature SOFCs based on the directly assembled high-performance and durable Sr-free CBP cathodes. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. The single cell of low temperature solid oxide fuel cell with sodium carbonate-SDC (samarium-doped ceria) as electrolyte and biodiesel as fuel

    Science.gov (United States)

    Rahmawati, F.; Nuryanto, A.; Nugrahaningtyas, K. D.

    2016-02-01

    In this research NSDC (composite of Na2CO3-SDC) was prepared by the sol-gel method to produce NSDC1 and also by the ceramic method to produce NSDC2. The prepared NSDC then were analyzed by XRD embedded with Le Bail refinement to study the change of characteristic peaks, their crystal structure, and their cell parameters. Meanwhile, the measurement of impedance was conducted to study the electrical conductivity of the prepared materials. A single cell was prepared by coating NSDC-L (a composite of NSDC with Li0.2Ni0.7Cu0.1O2) on both surfaces of NSDC. The NSDC-L was used as anode and cathode. The ionic conductivity of NSDC1 and NSDC2 at 400 oC are 4.1109 x 10-2 S.cm-1 and 1.6231 x 10-2 S.cm-1, respectively. Both electrolytes have ionic conductivity higher than 1 x 10-4 S.cm-1, therefore, can be categorized as good electrolyte [1]. However, the NSDC1 shows electrodeelectrolyte conduction. It indicates the existence of electronic migration from electrolyte- electrode or vice versa. Those may cause a short circuit during fuel cell operation and will reduce the fuel cell performance fastly. The single cell tests were conducted at 300, 400, 500 and 600 °C. The single fuel cell with NSDC1 and NSDC2 as electrolyte show maximum power density at 400 °C with the power density of 3.736 x 10-2 mW.cm-2 and 2.245 x 10-2 mW.cm-2, respectively.

  15. Human interphase chromosomes: a review of available molecular cytogenetic technologies

    Directory of Open Access Journals (Sweden)

    Yurov Yuri B

    2010-01-01

    Full Text Available Abstract Human karyotype is usually studied by classical cytogenetic (banding techniques. To perform it, one has to obtain metaphase chromosomes of mitotic cells. This leads to the impossibility of analyzing all the cell types, to moderate cell scoring, and to the extrapolation of cytogenetic data retrieved from a couple of tens of mitotic cells to the whole organism, suggesting that all the remaining cells possess these genomes. However, this is far from being the case inasmuch as chromosome abnormalities can occur in any cell along ontogeny. Since somatic cells of eukaryotes are more likely to be in interphase, the solution of the problem concerning studying postmitotic cells and larger cell populations is interphase cytogenetics, which has become more or less applicable for specific biomedical tasks due to achievements in molecular cytogenetics (i.e. developments of fluorescence in situ hybridization -- FISH, and multicolor banding -- MCB. Numerous interphase molecular cytogenetic approaches are restricted to studying specific genomic loci (regions being, however, useful for identification of chromosome abnormalities (aneuploidy, polyploidy, deletions, inversions, duplications, translocations. Moreover, these techniques are the unique possibility to establish biological role and patterns of nuclear genome organization at suprachromosomal level in a given cell. Here, it is to note that this issue is incompletely worked out due to technical limitations. Nonetheless, a number of state-of-the-art molecular cytogenetic techniques (i.e multicolor interphase FISH or interpahase chromosome-specific MCB allow visualization of interphase chromosomes in their integrity at molecular resolutions. Thus, regardless numerous difficulties encountered during studying human interphase chromosomes, molecular cytogenetics does provide for high-resolution single-cell analysis of genome organization, structure and behavior at all stages of cell cycle.

  16. Preparation of anode-electrolyte structures using graphite, sodium bicarbonate or citric acid as pore forming agents for application in solid oxide fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Paz Fiuza, Raigenis da; Silva, Marcos Aurelio da; Guedes, Bruna C.; Pontes, Luiz A.; Boaventura, Jaime Soares [UFBA, Salvador, Bahia (Brazil). Energy and Materials Science Group

    2010-07-01

    Cermets based on Ni supported on YSZ or GDC were prepared for use as anode in direct reform SOFCs. NaHCO3 (Na-Ni-YSZ and Na-Ni-GDC) or citric acid (Ac-Ni-YSZ and Ac-Ni-GDC) were used as pore forming agents (PFAs). The SOFC anode was also prepared using graphite (G-Ni-YSZ and G-Ni-GDC) as PFA for the purposes of comparison. The testing unitary SOFC, planar type, was made by pressing the anode-electrolyte assembly, followed by sintering at 1500 C. After this, LSM (lanthanum and strontium manganite) paint was used for the cathode deposition. The powdered cermets were evaluated in ethanol steam reforming at 650 C. The ethanol conversion was 84% and 32% for cermets Na-Ni-YSZ and G-Ni-YSZ, respectively and the selectivity to H{sub 2} was 32 and 20% for the two cermets, respectively. The Na-Ni-YSZ cermet was ten times more resistant to carbon deposition than the G-Ni-YSZ cermet. SEM micrographs of the anode-electrolyte assembly showed that the use of NaHCO{sub 3} as PFA created a well formed interface between layers with homogeneously distributed pores. In contrast, graphite as PFA formed a loose interface between anode and electrolyte. The performance of the unitary SOFC was evaluated using ethanol, hydrogen or methane as fuel. The cell operated well using any of these fuels; however, they exhibited different electrochemical behavior. (orig.)

  17. Fabrication of a large area cathode-supported thin electrolyte film for solid oxide fuel cells via tape casting and co-sintering techniques

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Chunhua; Liu, Renzhu; Wang, Shaorong; Wen, Tinglian [Shanghai Institute of Ceramics, Chinese Academy of Sciences (SICCAS), 1295 Dingxi Road, Shanghai 200050 (China)

    2009-04-15

    A large area cathode-supported electrolyte film, comprising porous (La{sub 0.8}Sr{sub 0.2}){sub 0.95}MnO{sub 3} (LSM95) cathode substrate, LSM95/Zr{sub 0.89}Sc{sub 0.1}Ce{sub 0.01}O{sub 2-x} (SSZ) cathode active layer, and SSZ electrolyte, has been successfully fabricated by tape casting and co-sintering techniques. The interface reaction between cathode and electrolyte was inhibited by using A-site deficient LSM. A dense enough SSZ thin film with a thickness of {proportional_to}26 {mu}m was obtained at 1250 C. By using Pt as anode, the obtained single cell reached the maximum power density of 0.54 W cm{sup -2} at 800 C in O{sub 2}/humidified H{sub 2}, with open circuit voltage (OCV) value of 1.08 V. (author)

  18. Electrolyte salts for nonaqueous electrolytes

    Science.gov (United States)

    Amine, Khalil; Zhang, Zhengcheng; Chen, Zonghai

    2012-10-09

    Metal complex salts may be used in lithium ion batteries. Such metal complex salts not only perform as an electrolyte salt in a lithium ion batteries with high solubility and conductivity, but also can act as redox shuttles that provide overcharge protection of individual cells in a battery pack and/or as electrolyte additives to provide other mechanisms to provide overcharge protection to lithium ion batteries. The metal complex salts have at least one aromatic ring. The aromatic moiety may be reversibly oxidized/reduced at a potential slightly higher than the working potential of the positive electrode in the lithium ion battery. The metal complex salts may also be known as overcharge protection salts.

  19. Multi-layered proton-conducting electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Tae H.; Dorris, Stephen E.; Balachandran, Uthamalingam

    2017-06-27

    The present invention provides a multilayer anode/electrolyte assembly comprising a porous anode substrate and a layered solid electrolyte in contact therewith. The layered solid electrolyte includes a first dense layer of yttrium-doped barium zirconate (BZY), optionally including another metal besides Y, Ba, and Zr (e.g., a lanthanide metal such as Pr) on one surface thereof, a second dense layer of yttrium-doped barium cerate (BCY), and an interfacial layer between and contacting the BZY and BCY layers. The interfacial layer comprises a solid solution of the BZY and BCY electrolytes. The porous anode substrate comprises at least one porous ceramic material that is stable to carbon dioxide and water (e.g., porous BZY), as well as an electrically conductive metal and/or metal oxide (e.g., Ni, NiO, and the like).

  20. Quantitative 3-D texture analysis of interphase cell nuclei

    NARCIS (Netherlands)

    Strasters, K.C.; Smeulders, A.W.M.; van der Voort, H.T.M.; Young, I.T.; Nanninga, N.; Young, I.T.

    1992-01-01

    In order to investigate the spatio-temporal structure of chromatin in interphase nuclei the authors present two 3-D texture parameters based on the grey-weighted distance transform that quantify the accessibility and the homogeneity of a nucleus. Results of experiments on computer generated textures

  1. Cell-fusion method to visualize interphase nuclear pore formation.

    Science.gov (United States)

    Maeshima, Kazuhiro; Funakoshi, Tomoko; Imamoto, Naoko

    2014-01-01

    In eukaryotic cells, the nucleus is a complex and sophisticated organelle that organizes genomic DNA to support essential cellular functions. The nuclear surface contains many nuclear pore complexes (NPCs), channels for macromolecular transport between the cytoplasm and nucleus. It is well known that the number of NPCs almost doubles during interphase in cycling cells. However, the mechanism of NPC formation is poorly understood, presumably because a practical system for analysis does not exist. The most difficult obstacle in the visualization of interphase NPC formation is that NPCs already exist after nuclear envelope formation, and these existing NPCs interfere with the observation of nascent NPCs. To overcome this obstacle, we developed a novel system using the cell-fusion technique (heterokaryon method), previously also used to analyze the shuttling of macromolecules between the cytoplasm and the nucleus, to visualize the newly synthesized interphase NPCs. In addition, we used a photobleaching approach that validated the cell-fusion method. We recently used these methods to demonstrate the role of cyclin-dependent protein kinases and of Pom121 in interphase NPC formation in cycling human cells. Here, we describe the details of the cell-fusion approach and compare the system with other NPC formation visualization methods. Copyright © 2014 Elsevier Inc. All rights reserved.

  2. Trichostatin A induced histone acetylation causes decondensation of interphase chromatin.

    NARCIS (Netherlands)

    T.A. Knoch (Tobias); M. Wachsmuth (Malte); M. Frank-Stöhr (Monika); M. Stöhr (Michael); C.P. Bacher (Christian); K. Rippe (Karsten)

    2004-01-01

    textabstractThe effect of trichostatin A (TSA)-induced histone acetylation on the interphase chromatin structure was visualized in vivo with a HeLa cell line stably expressing histone H2A, which was fused to enhanced yellow fluorescent protein. The globally increased histone acetylation caused a

  3. High elastic modulus polymer electrolytes

    Science.gov (United States)

    Balsara, Nitash Pervez; Singh, Mohit; Eitouni, Hany Basam; Gomez, Enrique Daniel

    2013-10-22

    A polymer that combines high ionic conductivity with the structural properties required for Li electrode stability is useful as a solid phase electrolyte for high energy density, high cycle life batteries that do not suffer from failures due to side reactions and dendrite growth on the Li electrodes, and other potential applications. The polymer electrolyte includes a linear block copolymer having a conductive linear polymer block with a molecular weight of at least 5000 Daltons, a structural linear polymer block with an elastic modulus in excess of 1.times.10.sup.7 Pa and an ionic conductivity of at least 1.times.10.sup.-5 Scm.sup.-1. The electrolyte is made under dry conditions to achieve the noted characteristics.

  4. Novel Li[(CF3SO2)(n-C4F9SO2)N]-Based Polymer Electrolytes for Solid-State Lithium Batteries with Superior Electrochemical Performance.

    Science.gov (United States)

    Ma, Qiang; Qi, Xingguo; Tong, Bo; Zheng, Yuheng; Feng, Wenfang; Nie, Jin; Hu, Yong-Sheng; Li, Hong; Huang, Xuejie; Chen, Liquan; Zhou, Zhibin

    2016-11-02

    Solid polymer electrolytes (SPEs) would be promising candidates for application in high-energy rechargeable lithium (Li) batteries to replace the conventional organic liquid electrolytes, in terms of the enhanced safety and excellent design flexibility. Herein, we first report novel perfluorinated sulfonimide salt-based SPEs, composed of lithium (trifluoromethanesulfonyl)(n-nonafluorobutanesulfonyl)imide (Li[(CF3SO2)(n-C4F9SO2)N], LiTNFSI) and poly(ethylene oxide) (PEO), which exhibit relatively efficient ionic conductivity (e.g., 1.04 × 10-4 S cm-1 at 60 °C and 3.69 × 10-4 S cm-1 at 90 °C) and enough thermal stability (>350 °C), for rechargeable Li batteries. More importantly, the LiTNFSI-based SPEs could not only deliver the excellent interfacial compatibility with electrodes (e.g., Li-metal anode, LiFePO4 and sulfur composite cathodes), but also afford good cycling performances for the Li|LiFePO4 (>300 cycles at 1C) and Li-S cells (>500 cycles at 0.5C), in comparison with the conventional LiTFSI (Li[(CF3SO2)2N])-based SPEs. The interfacial impedance and morphology of the cycled Li-metal electrodes are also comparatively analyzed by electrochemical impedance spectra and scanning electron microscopy, respectively. These indicate that the LiTNFSI-based SPEs would be potential alternatives for application in high-energy solid-state Li batteries.

  5. Effects of some rare earth and carbonate-based co-dopants on structural and electrical properties of samarium doped ceria (SDC) electrolytes for solid oxide fuel cells

    Science.gov (United States)

    Anwar, Mustafa; Khan, Zuhair S.; Mustafa, Kamal; Rana, Akmal

    2015-09-01

    In the present study, samarium doped ceria (SDC) and SDC-based composite with the addition of K2CO3 were prepared by co-precipitation route and effects of pH of the solution and calcination temperature on microstructure of SDC and SDC-K2CO3, respectively, were investigated. Furthermore, experimentation was performed to investigate into the ionic conductivity of pure SDC by co-doping with yttrium i.e., YSDC, XRD and SEM studies show that the crystallite size and particle size of SDC increases with the increase in pH. The SEM images of all the samples of SDC synthesized at different pH values showed the irregular shaped and dispersed particles. SDC-K2CO3 was calcined at 600∘C, 700∘C and 800∘C for 4 h and XRD results showed that crystallite size increases while lattice strain, decreases with the increase in calcination temperature and no peaks were detected for K2CO3 as it is present in an amorphous form. The ionic conductivity of the electrolytes increases with the increase in temperature and SDC-K2CO3 shows the highest value of ionic conductivity as compared to SDC and YSDC. Chemical compatibility tests were performed between the co-doped electrolyte and lithiated NiO cathode at high temperature. It revealed that the couple could be used up to the temperature of 700∘C.

  6. Tailoring Ba3Ca1.18Nb1.82O9-δ with NiO as electrolyte for proton-conducting solid oxide fuel cells

    Science.gov (United States)

    Zhu, Zhiwen; Guo, Enyan; Wei, Zhaoling; Wang, Huiqiang

    2018-01-01

    A strategy of tailoring Ba3Ca1.18Nb1.82O9-δ (BCN) is proposed, aiming to improve the sinterability and conductivity of BCN material for fuel cell applications. The new Ba3Ca1.18Nb1.77Ni0.05O9-δ (BCNNi) material shows a significant improvement in sinterability compared with BCN, leading to a high densification for BCNNi after sintering at as low as 1400 °C. In addition, the BCNNi exhibits a conductivity of 4.59 × 10-3 S cm-1 at 700 °C that is not only higher than that for BCN which only reaches 3.45 × 10-3 S cm-1 at the same temperature but also shows a significant improvement compared with that for BCN-based materials in literature reports. As a result, the cell with the BCNNi electrolyte shows a peak power density of 84 mW cm-2 at 700 °C which is also one of the largest ever reported for this type of cells. Further electrochemical studies indicate that the high conductivity of BCNNi electrolyte membrane benefits the fuel cell performance.

  7. Highly mobile segments in crystalline poly(ethylene oxide)8:NaPF6 electrolytes studied by solid-state NMR spectroscopy

    Science.gov (United States)

    Luo, Huan; Liang, Xinmiao; Wang, Liying; Zheng, Anmin; Liu, Chaoyang; Feng, Jiwen

    2014-02-01

    Two types of high-crystallinity poly(ethylene oxide)/NaPF6 electrolytes with ethylene oxide (EO)/Na molar ratios of 8:1 and 6:1, termed as PEO8:NaPF6 and PEO6:NaPF6 with Mw = 6000 g mol-1 were prepared, and their ionic conductivity, structure, and segmental motions were investigated and compared. PEO8:NaPF6 polymer electrolyte exhibits the room-temperature ionic conductivity 7.7 × 10-7 S cm-1 which is about five times higher than the PEO6:NaPF6. By variable-temperature measurements of static powder spectra and 1H spin-lattice relaxation time in rotation frame (1H T1ρ), we demonstrate that crystalline segments are more highly mobile in the crystalline PEO8:NaPF6 with higher ionic conductivity than in the PEO6:NaPF6 with lower ionic conductivity. The large-angle reorientation motion of polymer segments in the PEO8:NaPF6 onsets at lower temperature (˜233 K) with a low activation energy 0.31 eV that is comparable with that of the pure PEO crystal. Whereas, the large-angle reorientation motion of polymer segments in the PEO6:NaPF6 starts around 313 K with a high activation energy of 0.91 eV. As a result of the temperature-enhanced large-angle reorientations, the 13C static powder lineshape changes markedly from a low-temperature wide pattern with apparent principal values of chemical shift δ33 δ22 (δ11). It is suggested that the segmental motion in crystalline PEO-salt complex promotes ionic conductivity.

  8. Electrolyte materials containing highly dissociated metal ion salts

    Energy Technology Data Exchange (ETDEWEB)

    Lee, H.S.; Geng, L.; Skotheim, T.A.

    1996-07-23

    The present invention relates to metal ion salts which can be used in electrolytes for producing electrochemical devices, including both primary and secondary batteries, photoelectrochemical cells and electrochromic displays. The salts have a low energy of dissociation and may be dissolved in a suitable polymer to produce a polymer solid electrolyte or in a polar aprotic liquid solvent to produce a liquid electrolyte. The anion of the salts may be covalently attached to polymer backbones to produce polymer solid electrolytes with exclusive cation conductivity. 2 figs.

  9. Electrolyte materials containing highly dissociated metal ion salts

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Hung-Sui (East Setauket, NY); Geng, Lin (Coram, NY); Skotheim, Terje A. (Shoreham, NY)

    1996-07-23

    The present invention relates to metal ion salts which can be used in electrolytes for producing electrochemical devices, including both primary and secondary batteries, photoelectrochemical cells and electrochromic displays. The salts have a low energy of dissociation and may be dissolved in a suitable polymer to produce a polymer solid electrolyte or in a polar aprotic liquid solvent to produce a liquid electrolyte. The anion of the salts may be covalently attached to polymer backbones to produce polymer solid electrolytes with exclusive cation conductivity.

  10. Patterning of lithium lanthanum titanium oxide films by soft lithography as electrolyte for all-solid-state Li-ion batteries

    NARCIS (Netherlands)

    Kokal, I.; Göbel, Ole; van den Ham, E.J.; ten Elshof, Johan E.; Notten, P.H.L.; Hintzen, H.T.

    2015-01-01

    The combination of sol–gel processing and soft-lithographic patterning presents a promising route towards three-dimensional (3D) micro Li-ion electrodes, and may offer a viable approach for the fabrication of all-solid-state 3D Li-ion batteries. The methods are relatively simple and therefore cheap

  11. Highly mobile segments in crystalline poly(ethylene oxide){sub 8}:NaPF{sub 6} electrolytes studied by solid-state NMR spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Luo, Huan; Liang, Xinmiao [State Key Laboratory of Magnetic Resonance and Atomic and Molecular Physics, Wuhan Center for Magnetic Resonance, Wuhan Institute of Physics and Mathematics, Chinese Academy of Science, Wuhan 430071 (China); University of Chinese Academy of Science, Beijing 100029 (China); Wang, Liying; Zheng, Anmin; Liu, Chaoyang; Feng, Jiwen, E-mail: jwfeng@wipm.ac.cn [State Key Laboratory of Magnetic Resonance and Atomic and Molecular Physics, Wuhan Center for Magnetic Resonance, Wuhan Institute of Physics and Mathematics, Chinese Academy of Science, Wuhan 430071 (China)

    2014-02-21

    Two types of high-crystallinity poly(ethylene oxide)/NaPF{sub 6} electrolytes with ethylene oxide (EO)/Na molar ratios of 8:1 and 6:1, termed as PEO{sub 8}:NaPF{sub 6} and PEO{sub 6}:NaPF{sub 6} with M{sub w} = 6000 g mol{sup −1} were prepared, and their ionic conductivity, structure, and segmental motions were investigated and compared. PEO{sub 8}:NaPF{sub 6} polymer electrolyte exhibits the room-temperature ionic conductivity 7.7 × 10{sup −7} S cm{sup −1} which is about five times higher than the PEO{sub 6}:NaPF{sub 6}. By variable-temperature measurements of static powder spectra and {sup 1}H spin-lattice relaxation time in rotation frame ({sup 1}H T{sub 1ρ}), we demonstrate that crystalline segments are more highly mobile in the crystalline PEO{sub 8}:NaPF{sub 6} with higher ionic conductivity than in the PEO{sub 6}:NaPF{sub 6} with lower ionic conductivity. The large-angle reorientation motion of polymer segments in the PEO{sub 8}:NaPF{sub 6} onsets at lower temperature (∼233 K) with a low activation energy 0.31 eV that is comparable with that of the pure PEO crystal. Whereas, the large-angle reorientation motion of polymer segments in the PEO{sub 6}:NaPF{sub 6} starts around 313 K with a high activation energy of 0.91 eV. As a result of the temperature-enhanced large-angle reorientations, the {sup 13}C static powder lineshape changes markedly from a low-temperature wide pattern with apparent principal values of chemical shift δ{sub 33} < δ{sub 22} < δ{sub 11} to a high-temperature narrow pattern of uniaxial chemical shift anisotropy δ{sub 33} > δ{sub 22} (δ{sub 11}). It is suggested that the segmental motion in crystalline PEO-salt complex promotes ionic conductivity.

  12. Multifunctionality in epoxy/glass fibers composites with graphene interphase

    OpenAIRE

    Mahmood, Haroon

    2017-01-01

    In this project, the synergetic effect of a graphene interphase in epoxy/glass fibers composites was investigated by coating glass fibers (GF) with graphene oxide (GO) and reduced graphene oxide (rGO) nanosheets by an electrophoretic deposition (EPD) technique. Graphite oxide was prepared using modified Hummers method in which raw graphite powder was oxidized using potassium permanganate (KMnO4) in acidic solution. Using ultrasonic technique, the graphite oxide was dispersed homogenously in w...

  13. Growth of the Mammalian Golgi Apparatus during Interphase.

    Science.gov (United States)

    Sin, Alex T-W; Harrison, Rene E

    2016-09-15

    During the cell cycle, genetic materials and organelles are duplicated to ensure that there is sufficient cellular content for daughter cells. While Golgi growth in interphase has been observed in lower eukaryotes, the elaborate ribbon structure of the mammalian Golgi apparatus has made it challenging to monitor. Here we demonstrate the growth of the mammalian Golgi apparatus in its protein content and volume during interphase. Through ultrastructural analyses, physical growth of the Golgi apparatus was revealed to occur by cisternal elongation of the individual Golgi stacks. By examining the timing and regulation of Golgi growth, we established that Golgi growth starts after passage through the cell growth checkpoint at late G1 phase and continues in a manner highly correlated with cell size growth. Finally, by identifying S6 kinase 1 as a major player in Golgi growth, we revealed the coordination between cell size and Golgi growth via activation of the protein synthesis machinery in early interphase. Copyright © 2016, American Society for Microbiology. All Rights Reserved.

  14. Promoters active in interphase are bookmarked during mitosis by ubiquitination.

    Science.gov (United States)

    Arora, Mansi; Zhang, Jie; Heine, George F; Ozer, Gulcin; Liu, Hui-wen; Huang, Kun; Parvin, Jeffrey D

    2012-11-01

    We analyzed modification of chromatin by ubiquitination in human cells and whether this mark changes through the cell cycle. HeLa cells were synchronized at different stages and regions of the genome with ubiquitinated chromatin were identified by affinity purification coupled with next-generation sequencing. During interphase, ubiquitin marked the chromatin on the transcribed regions of ∼70% of highly active genes and deposition of this mark was sensitive to transcriptional inhibition. Promoters of nearly half of the active genes were highly ubiquitinated specifically during mitosis. The ubiquitination at the coding regions in interphase but not at promoters during mitosis was enriched for ubH2B and dependent on the presence of RNF20. Ubiquitin labeling of both promoters during mitosis and transcribed regions during interphase, correlated with active histone marks H3K4me3 and H3K36me3 but not a repressive histone modification, H3K27me3. The high level of ubiquitination at the promoter chromatin during mitosis was transient and was removed within 2 h after the cells exited mitosis and entered the next cell cycle. These results reveal that the ubiquitination of promoter chromatin during mitosis is a bookmark identifying active genes during chromosomal condensation in mitosis, and we suggest that this process facilitates transcriptional reactivation post-mitosis.

  15. Y and Ni Co-Doped BaZrO3 as a Proton-Conducting Solid Oxide Fuel Cell Electrolyte Exhibiting Superior Power Performance

    KAUST Repository

    Shafi, Shahid P.

    2015-10-16

    The fabrication of anode supported single cells based on BaZr0.8Y0.2O3-δ (BZY20) electrolyte is challenging due to its poor sinteractive nature. The acceleration of shrinkage behavior, improved sinterability and larger grain size were achieved by the partial substitution of Zr with Ni in the BZY perovskite. Phase pure Ni-doped BZY powders of nominal compositions BaZr0.8-xY0.2NixO3-δ were synthesized up to x = 0.04 using a wet chemical combustion synthesis route. BaZr0.76Y0.2Ni0.04O3-δ (BZYNi04) exhibited adequate total conductivity and the open circuit voltage (OCV) values measured on the BZYNi04 pellet suggested lack of significant electronic contribution. The improved sinterability of BZYNi04 assisted the ease in film fabrication and this coupled with the application of an anode functional layer and a suitable cathode, PrBaCo2O5+δ (PBCO), resulted in a superior fuel cell power performance. With humidified hydrogen and static air as the fuel and oxidant, respectively, a peak power density value of 428 and 240 mW cm−2 was obtained at 700 and 600°C, respectively.

  16. Yttrium and Nickel Co-Doped BaZrO3 as a Proton-Conducting Electrolyte for Intermediate Temperature Solid Oxide Fuel Cells

    KAUST Repository

    Shafi, S. P.

    2015-07-17

    High temperature proton conducting oxides, due to their lower activation energy for proton conduction, can achieve high conductivity at relatively low temperatures (500-700°C). Though BaZr0.8Y0.2O3-δ (BZY) perovskite exhibits good chemical stability and high bulk conductivity, high grain boundary resistance decreases its total conductivity. This work focuses on substitution of Zr4+ with Ni2+ in the perovskite B-site in a targeted fashion in order to promote the sinterability of BZY. Powder X-ray diffraction analysis showed the formation of single phases for Ba0.8-xY0.2NixO3-δ compositions up to x = 0.04. Scanning electron microscopy (SEM) image analysis demonstrated that densification is promoted by increasing the Ni-content, reaching a fully dense microstructure for Ba0.76Y0.2Ni0.04O3-δ (BZYNi04). An anode supported single cell based on BZYNi04 electrolyte showed superior power performance, achieving 240 and 428 mW cm-2 at 600 and 700°C, respectively. © The Electrochemical Society.

  17. Analytic and computational micromechanics of clustering and interphase effects in carbon nanotube composites.

    Energy Technology Data Exchange (ETDEWEB)

    Seidel, Gary D.; Hammerand, Daniel Carl; Lagoudas, Dimitris C. (Texas A& M University, College Station, TX)

    2006-01-01

    Effective elastic properties for carbon nanotube reinforced composites are obtained through a variety of micromechanics techniques. Using the in-plane elastic properties of graphene, the effective properties of carbon nanotubes are calculated utilizing a composite cylinders micromechanics technique as a first step in a two-step process. These effective properties are then used in the self-consistent and Mori-Tanaka methods to obtain effective elastic properties of composites consisting of aligned single or multi-walled carbon nanotubes embedded in a polymer matrix. Effective composite properties from these averaging methods are compared to a direct composite cylinders approach extended from the work of Hashin and Rosen (1964) and Christensen and Lo (1979). Comparisons with finite element simulations are also performed. The effects of an interphase layer between the nanotubes and the polymer matrix as result of functionalization is also investigated using a multi-layer composite cylinders approach. Finally, the modeling of the clustering of nanotubes into bundles due to interatomic forces is accomplished herein using a tessellation method in conjunction with a multi-phase Mori-Tanaka technique. In addition to aligned nanotube composites, modeling of the effective elastic properties of randomly dispersed nanotubes into a matrix is performed using the Mori-Tanaka method, and comparisons with experimental data are made. Computational micromechanical analysis of high-stiffness hollow fiber nanocomposites is performed using the finite element method. The high-stiffness hollow fibers are modeled either directly as isotropic hollow tubes or equivalent transversely isotropic effective solid cylinders with properties computed using a micromechanics based composite cylinders method. Using a representative volume element for clustered high-stiffness hollow fibers embedded in a compliant matrix with the appropriate periodic boundary conditions, the effective elastic properties

  18. [Application of interphase FISH on cell smears in detection of hematological diseases].

    Science.gov (United States)

    Sun, Wan-Ling; Liu, Cong-Yan; Li, Hui; He, Jing-Juan; Sun, Xue-Jing; Xu, Juan

    2010-02-01

    The study was aimed to investigate the application value of interphase fluorescence in situ hybridization (FISH) on cell smears in hematological diseases. Both interphase FISH on peripheral blood smears and bone marrow smears treated by methanol/acetic acid, and routine interphase FISH of bone marrow cells dropped on slides were done at the same time, in order to detect Ph chromosome by BCR/ABL dual color, dual fusion probe in 20 patients with chronic myelogenous leukemia or acute lymphoblastic leukemia which had been proven to display Ph chromosome positive. The results indicated that as compared with routine interphase FISH, the interphase FISH on cell smears could also offer reliable result. It is concluded that interphase FISH on cell smears is a kind of reliable and time-saving technique, which is also suitable for retrospective research and worthy to further apply in clinic.

  19. Synthesis and ceramic processing of zirconia alumina composites for application as solid oxide fuel cell electrolytes; Sintese e processamento de compositos de zirconia-alumina para aplicacao como eletrolito em celulas a combustivel de oxido solido

    Energy Technology Data Exchange (ETDEWEB)

    Garcia, Rafael Henrique Lazzari

    2007-07-01

    The global warmness and the necessity to obtain clean energy from alternative methods than petroleum raises the importance of developing cleaner and more efficient systems of energy generation, among then, the solid oxide fuel cell (SOFC). Cubic stabilized zirconia (CSZ) has been the most studied material as electrolyte in SOFC, due to its ionic conductivity and great stability at operation conditions. However, its low fracture toughness difficulties its application as a thin layer, what could lead to an improvement of cell efficiency. In this sense, the alumina addition in CSZ forms a composite, which can shift its mechanical properties, without compromising its electrical properties. In this work, coprecipitation synthesis route and ceramic processing of zirconia-alumina composites were studied, in order to establish optimum conditions to attain high density, homogeneous microstructure, and better mechanical properties than CSZ, without compromising ionic conductivity. For this purpose, composites containing up to 40 wt % of alumina, in a 9 mol % yttria-stabilized zirconia (9Y-CSZ) matrix were evaluated. In order to optimize the synthesis of the composites, a preliminary study of powder obtaining and processing were carried out, at compositions containing 20 wt % of alumina, in 9Y-CSZ. The ceramic powders were characterized by helium picnometry, X-ray diffraction, scanning electronic microscopy, transmission electronic microscopy, thermogravimetry, differential scanning calorimetry, granulometry by laser diffraction and gas adsorption (BET). The characterization of sinterized compacts were performed by X-ray diffraction, scanning electron microscopy, optical microscopy, density measurements, Vickers indentation and impedance spectroscopy. The obtained results show that the alumina addition, in the 9Y-CSZ matrix powders, raises the specific surface area, promotes deagglomeration of powders and elevates the oxides crystallization temperature, requiring higher

  20. 1,2,4-Triazolium perfluorobutanesulfonate as an archetypal pure protic organic ionic plastic crystal electrolyte for all-solid-state fuel cells

    DEFF Research Database (Denmark)

    Luo, Jiangshui; Jensen, Annemette Hindhede; Brooks, Neil R.

    2015-01-01

    1,2,4-Triazolium perfluorobutanesulfonate (1), a novel, pure protic organic ionic plastic crystal (POIPC) with a wide plastic crystalline phase, has been explored as a proof-of-principle anhydrous proton conductor for all-solid-state high temperature hydrogen/air fuel cells. Its physicochemical...... properties, including thermal, mechanical, structural, morphological, crystallographic, spectral, and ion-conducting properties, as well as fuel cell performances, have been studied comprehensively in both fundamental and device-oriented aspects. With superior thermal stability, 1 exhibits crystal (phase III...... patterns further illustrate the structural changes. Electrochemical hydrogen pumping tests confirm the protonic nature of the ionic conduction observed in the lower plateau region. Finally, measurements of the open circuit voltages (OCVs) and the polarization curves of a dry hydrogen/air fuel cell prove...