Analysis of barium hydroxide and calcium hydroxide slurry carbonation reactors

International Nuclear Information System (INIS)

Patch, K.D.; Hart, R.P.; Schumacher, W.A.

1980-05-01

The removal of CO 2 from air was investigated by using a continuous-agitated-slurry carbonation reactor containing either barium hydroxide [Ba(OH) 2 ] or calcium hydroxide [Ca(OH) 2 ]. Such a process would be applied to scrub 14 CO 2 from stack gases at nuclear-fuel reprocessing plants. Decontamination factors were characterized for reactor conditions which could alter hydrodynamic behavior. An attempt was made to characterize reactor performance with models assuming both plug flow and various degrees of backmixing in the gas phase. The Ba(OH) 2 slurry enabled increased conversion, but apparently the process was controlled under some conditions by phenomena differing from those observed for carbonation by Ca(OH) 2 . Overall reaction mechanisms are postulated

Comparative evaluation of different forms of calcium hydroxide in apexification

OpenAIRE

Subhankar Ghosh; Dibyendu Mazumdar; Pradip Kumar Ray; Bhaswar Bhattacharya

2014-01-01

Background: One out of every two children sustains a dental injury most often between 8 and 10 years of age. Majority of these teeth subsequently become non-vital and most often with immature apex. Management of these teeth is an enormous challenge for lack of apical stop. Calcium hydroxide in various formulations has maximum literature support in favor of "successful apexification or induced apical closure." Aim: The aim of the following study is to determine the efficacy of calcium hydroxid...

Clinical effect of calcium hydroxide paste combined with triple antibiotic paste on root canal disinfection

Directory of Open Access Journals (Sweden)

Chen QU

2014-03-01

Full Text Available Objective　To compare the efficacy in disinfection and pain control of calcium hydroxide paste and triple antibiotic paste (ornidazole, ciprofloxacin and minocycline used individually or jointly for root canal disinfection. Methods　Two hundred and thirty-five patients with chronic apical periodontitis (235 teeth were involved in the present study and divided into 2 groups: fistula group (n=118 and no fistula group (n=117. Each group was then randomly divided into 4 subgroups: calcium hydroxide paste group, triple antibiotic paste group, calcium hydroxide + triple antibiotic paste group, and camphor phenol group. After regular root canal preparation, root canals of patients in 4 groups were filled with tiny paper ends impregnated with fore 4 different drugs respectively. Visual analogue scales (VAS of pain were given to the patients with a guide for filling the scale. One week later, both the data of the scales and the effects of root canal disinfection were recorded and analyzed. Results　Seven days after treatment, the clinical efficacy of calcium hydroxide paste, triple antibiotic paste and calcium hydroxide + triple antibiotic paste was similar (P>0.05 either in fistula group or in no fistula group, but all better than that of camphor phenol (P<0.05. VAS score analysis showed that, at least on the first 3 days after sealing medicine in the root canal, calcium hydroxide + triple antibiotic paste achieved better result of pain control than the other three groups (P<0.05 no matter with or without fistula. Conclusions 　Calcium hydroxide paste, triple antibiotic paste, calcium hydroxide + triple antibiotic paste are effective in treatment of chronic apical periodontitis whether with or without fistula. However, the combined use of calcium hydroxide and three antibiotic pastes is better for controlling the pain after root canal preparation than other treatments, which is therefore worthy of clinical application. DOI: 10.11855/j.issn.0577-7402.2014.02.12

Clinical Survey of Successfulness of DPC with MTA and Calcium Hydroxide

Directory of Open Access Journals (Sweden)

E.Yasini

2005-02-01

Full Text Available Statement of Problem: The pulp may be exposed during remove of caries or by traumatic and iatrogenicinjuries. The material used to DPC, must be biocompatible, scalable and prevent bacterial leakage.Furthermore, it is better to stimulate dentinogenesis. Calcium hydroxide is most usual material for DPC. But itcannot provide a suitablcbiologic seal. Mineral irioxide aggregate (MTA is also a suitable material for DPC.Purpose: The aim of this study was to compare the clinical success of DPC done with MTA or calciumhydroxide cement.Materials and Methods: In this study eighteen posterior teeth without previous spontaneous pain thatinvolved mechanicaly exposure was randomly selected and capped with MTA or calcium hydroxide. These teeth were evaluated by clinical vitality test and radiograph after 3 and 12 months, and patients werequestioned about irritative or spontancus pain in this period. Statistical analysis was carried out by Usher exacttest (a-0.05.Results: This study showed that in calcium hydroxid groud three had irreversible pulpitis and two teeth had symptom and signs of reversible pulpitis. While, In MTA group all cases were normaL and no clinical sign was evident.Conclusion: MTA exhibited better results than calcium hydroxide cement for the capping of the pulp in human

In vitro antibacterial effect of calcium hydroxide combined with chlorhexidine or iodine potassium iodide on Enterococcus faecalis.

Science.gov (United States)

Sirén, Eva K; Haapasalo, Markus P P; Waltimo, Tuomas M T; Ørstavik, Dag

2004-08-01

Several studies have shown a higher success rate of root canal therapy when the canal is free from bacteria at the time of obturation. Treatment strategies that are designed to eliminate this microflora should include agents that can effectively disinfect the root canal. Enterococcus faecalis is often associated with persistent endodontic infections. While in vivo studies have indicated calcium hydroxide to be the most effective all-purpose intracanal medicament, iodine potassium iodide (IKI) and chlorhexidine (CHX) may be able to kill calcium hydroxide-resistant bacteria. Supplementing the antibacterial activity of calcium hydroxide with IPI or CHX preparations was studied in bovine dentine blocks. While calcium hydroxide was unable to kill E. faecalis in the dentine, calcium hydroxide combined with IKI or CHX effectively disinfected the dentine. The addition of CHX or IKI did not affect the alkalinity of the calcium hydroxide suspensions. It may be assumed that combinations also have the potential to be used as long-term medication. Cytotoxicity tests using the neutral red method indicated that the combinations were no more toxic than their pure components.

Accidental periapical extrusion of non-setting calcium hydroxide: Unusual bone response and management

Directory of Open Access Journals (Sweden)

Divya S Sharma

2014-01-01

Full Text Available Premixed non-setting calcium hydroxide is frequently used as interim root canal dressing in endodontically involved permanent teeth and as obturating paste in deciduous teeth in pediatric dentistry. Wide apex in both cases makes it more prone for deliberate extrusion especially when applied with pressure delivery systems. Contrary to common belief the mix was not resorbed in two years with the complaint of insufficiency in mastication. Large mass of calcium hydroxide in bone delayed healing process even after its removal. The present case report intends to demonstrate unusual behavior of bone in response to oily non-setting preparation of calcium hydroxide. Therefore its application with pressure syringe should be reconsidered in pediatric dentistry.

The Effect of Calcium Hydroxide As an Intracanal Medication of The Apical Microleakage

Directory of Open Access Journals (Sweden)

Heshmat Mohajer AR

2011-12-01

Full Text Available Background and Aims: Nowadays, calcium hydroxide is used as a dressing for canal sterilization and repair progression of apical lesions. The aim of this study was to investigate the effect of calcium hydroxide as an intracanal medicament on the apical microleakage of root filling.Materials and Methods: In this experimental study, 46 extracted single-rooted human teeth were instrumented with step-back technique to master apical file (MAF size 35. Specimens were randomly divided into 2 groups (n = 20. In group 1, the specimens were treated with calcium hydroxide intracanal medication; and in group 2, the samples did not receive any medication. The teeth were incubated in 100% humidity at 37°C for one week. After that, calcium hydroxide was removed using irrigation with normal saline and reaming with MAF. The root canals were obturated with gutta- percha and AH26 sealer using lateral compaction technique. Specimens were incubated in 100% humility at 37°C for 72 hours and then immersed in India ink for 1 week. Finally, the teeth were cleared and the maximum linear dye penetration was measured under a stereomicroscope at 4X magnification. The data were analyzed by T-test and Chi-square.Results: There was no significant difference between the two experimental groups (P=0.068. Conclusion: The findings of this study indicated that using calcium hydroxide as an intracanal medicament did not influence the apical microleakage after final obturation of the root canal system.

Carbonation as a binding mechanism for coal/calcium hydroxide pellets. Final technical report, 1 September, 1992--31 August, 1993

Energy Technology Data Exchange (ETDEWEB)

Rapp, D.; Lytle, J.; Hackley, K.; Dagamac, M. [Illinois State Geological Survey, Champaign, IL (United States); Berger, R. [Univ. of Illinois, Urbana, IL (United States); Schanche, G. [Army Construction Engineering Research Lab., Champaign, IL (United States)

1993-12-31

This research was an investigation of calcium hydroxide, a sulfur-capturing sorbent, as a binder for coal fines. The reaction of carbon dioxide with calcium hydroxide, referred to as carbonation, was studied as a method for improving pellet quality. Carbonation forms a cementitious matrix of calcium carbonate. Research has demonstrated that calcium hydroxide is a viable binder for coal fines and that a roller-and-die pellet mill is an effective method of pellet formation. From a minus 28 mesh preparation plant fine coal sample, a roller-and-die pellet mill produced strong pellets when 5 and 10% calcium hydroxide was used as a binder. The pellets containing 10% calcium hydroxide strengthened considerably when air cured. This increase in strength was attributed to carbonation via atmospheric carbon dioxide. Pellets containing 10 wt% calcium hydroxide were produced using an extruder but pellets formed in this manner were much weaker than pellets produced with the roller-and-die mill. In tests performed using a laboratory hydraulic press, the effect of particle size and compaction pressure on pellet strength was studied. Particle distributions with mean sizes of 200, 90 and 40 microns were tested. The results indicate that pellet strength increased with decreasing particle size and increasing compaction pressure when calcium hydroxide was used as a binder. Pellets containing 10 wt% calcium hydroxide increased in strength by approximately 40% when air dried for one day. As above, this increase in strength was attributed to carbonation of the calcium hydroxide via atmospheric carbon dioxide.

Effect of supplementation with barley and calcium hydroxide on intake of Mediterranean shrubs

Directory of Open Access Journals (Sweden)

Dragan Skobic

2011-04-01

Full Text Available Maquis plant communities are one of the most varied vegetation types in the Mediterranean region and an important habitat for wild and domestic herbivores. Although the majority of these shrubs are nutritious, the secondary compounds are main impediments that reduce their forage value. In five experiments we determined the effect of supplementing goats with calcium hydroxide plus barley, and barley alone on intake of five dominant shrubs (Quercus ilex, Erica multiflora, Arbutus unedo, Viburnum tinus and Pistacia lentiscus of the Mediterranean maquis community. The combination of calcium hydroxide plus barley and barley alone increased utilization of all five investigated Mediterranean shrubs; therewith that intake of Arbutus unedo and Viburnum tinus was not statistically significant. Supplemented goats with calcium hydroxide plus barley or barley alone could be effective in controlling secondary compounds-rich Mediterranean shrubs where their abundance threatens biodiversity. This control can be facilitated by browsing dominant Mediterranean shrubs, which has been shown to be effective in managing Mediterranean maquis density. Calcium hydroxide and barley (energy enhance use of secondary compounds-containing plants, which may increase production of alternate forages and create a more diverse mix of plant species in the Mediterranean maquis plant community.

CALCIUM HYDROXIDE IN ENDODONTIC TREATMENT OF PERIAPICALLY INFECTED TEETH

Directory of Open Access Journals (Sweden)

Rahmi Alma Farah Adang

2006-04-01

Full Text Available An inadequate endodontic treatment may affect the root canal system and spread beyond its apical foramina that elicit periodontal tissue developing into abscess, granuloma and radicular cyst. Periodical lesions can be treated with non surgical endodontic treatment using calcium hydroxide dressing. This case study is reporting teeth 11 with periodical lesions and infection. Evidence of a clinical healing and radiographic assessments were followed by a non surgical endodontic therapy. Successful treatment outcome is related to the elimination of infection agents from the root canal. This can activate a stimulation zone to promote regeneration. Calcium hydroxide used as a root canal dressing may promote alkalinity at the adjacent tissue , create favourable environmental condition in which hard tissue formation can occur, interfere the bactericidal activity, increase mineralization, and induce healing.

The effect of radiopacifiers agents on pH, calcium release, radiopacity, and antimicrobial properties of different calcium hydroxide dressings.

Science.gov (United States)

Ordinola-Zapata, Ronald; Bramante, Clovis Monteiro; García-Godoy, Franklin; Moldauer, Bertram Ivan; Gagliardi Minotti, Paloma; Tercília Grizzo, Larissa; Duarte, Marco Antonio Hungaro

2015-07-01

The aim of this study was to evaluate the antimicrobial activity, pH level, calcium ion release, and radiopacity of calcium hydroxide pastes associated with three radiopacifying agents (iodoform, zinc oxide, and barium sulfate). For the pH and calcium release tests, 45 acrylic teeth were utilized and immersed in ultrapure water. After 24 h, 72 h, and 7 days the solution was analyzed by using a pH meter and an atomic absorption spectrophotometer. Polyethylene tubes filled with the pastes were used to perform the radiopacity test. For the antimicrobial test, 25 dentin specimens were infected intraorally in order to induce the biofilm colonization and treated with the pastes for 7 days. The Live/Dead technique and a confocal microscope were used to obtain the ratio of live cells. Parametric and nonparametric statistical tests were performed to show differences among the groups (P calcium release test on the 7th day (P > 0.05). The calcium hydroxide/iodoform samples had the highest radiopacity and antimicrobial activity against the biofilm-infected dentin in comparison to the other pastes (P Calcium hydroxide mixed with 17% iodoform and 35% propylene glycol into a paste had the highest pH, calcium ion release, radiopacity, and the greatest antimicrobial action versus similar samples mixed with BaSO4 or ZnO. © 2015 Wiley Periodicals, Inc.

Comparison of Calcium Hydroxide and Bioactive Glass after Direct Pulp Capping in Primary Teeth

Directory of Open Access Journals (Sweden)

R. Haghgoo

2007-12-01

Full Text Available Objective: Bioactive glass is often used as a filler material for repair of dental bone defects.In different studies osteogenic potential of this material was proved, but its dentinogenesisproperty is in doubt. The purpose of this study was to evaluate the histological pulp responses of Calcium hydroxide and Bioactive glass placed directly on exposed pulp tissues.Materials and Methods: Twenty teeth to be extracted due to orthodontic reasons were selected. These teeth were divided into two groups and treated with direct pulp capping.Calcium hydroxide was used for 10 teeth and Bioactive glass for 10 teeth. After 60 daysthe teeth were extracted and prepared for histological evaluation. Finally the data was analyzed with exact Fisher test.Results: All teeth treated with Calcium hydroxide showed inflammation. Internal resorption was seen in six teeth, abscess in five teeth and dentinal bridge in two teeth. Inflammationwas seen in three Bioactive glass samples and dentinal bridge in seven teeth, but internal resorption and abscess were not seen.Conclusion: Bioactive glass appears to be superior to Calcium hydroxide as a pulp capping agent in primary teeth.

40 CFR 721.10018 - Calcium hydroxide oxide silicate (Ca6(OH)2O2(Si2O5)3).

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Calcium hydroxide oxide silicate (Ca6... New Uses for Specific Chemical Substances § 721.10018 Calcium hydroxide oxide silicate (Ca6(OH)2O2... substance identified as calcium hydroxide oxide silicate (Ca6(OH)2O2(Si2O5)3) (PMN P-01-442; CAS No. 13169...

Effect of the Association of Nonsteroidal Anti-inflammatory and Antibiotic Drugs on Antibiofilm Activity and pH of Calcium Hydroxide Pastes.

Science.gov (United States)

de Freitas, Rafaela Pignatti; Greatti, Vanessa Raquel; Alcalde, Murilo Priori; Cavenago, Bruno Cavalini; Vivan, Rodrigo Ricci; Duarte, Marco Antonio Hungaro; Weckwerth, Ana Carolina Villas Bôas; Weckwerth, Paulo Henrique

2017-01-01

The objective of the present study was to evaluate the in vitro antibiofilm activity and pH of calcium hydroxide associated with different nonsteroidal anti-inflammatory drugs (NSAIDs). The groups analyzed were as follows: group 1, calcium hydroxide paste with propylene glycol; group 2, calcium hydroxide paste with propylene glycol + 5% diclofenac sodium; group 3, calcium hydroxide paste with propylene glycol + 5% ibuprofen; group 4, calcium hydroxide paste with propylene glycol + 5% ciprofloxacin; and group 6, positive control (without medication). For analysis of the pH, the pastes were inserted into tubes and immersed in flasks containing ultrapure water. At the time intervals of 3, 24, 72, and 168 hours, the pH was measured with a calibrated pH meter. For microbial analysis, biofilm was induced in 30 bovine dentin blocks for 21 days. Subsequently, the pastes were placed on the blocks with biofilm for 7 days. Afterward, the pastes were removed by irrigation with sterile water, and the specimens were analyzed with a laser scanning confocal microscope with the 50 μL Live/Dead BacLight Bacterial Viability solution L7012 Kit (Molecular Probes, Inc, Eugene, OR). Data were subjected to statistical analysis at a significance level of 5%. The highest pH values were found for calcium hydroxide associated with ciprofloxacin in all periods analyzed. With the exception of pure calcium hydroxide paste, the other groups showed statistically significant differences (P antibiotic did not interfere with the pH of calcium hydroxide paste and increased the antimicrobial action of calcium hydroxide paste against Enterococcus faecalis biofilm formation. Published by Elsevier Inc.

Root canal treatment of pulpless immature teeth using calcium hydroxide paste. Roentgenographic study

International Nuclear Information System (INIS)

Leite, R.M.G.V.; Abbud, R.

1986-01-01

Calcium hydroxide paste was used as a temporary dressing and the renewal was done each three months in the root treatment of immature teeth with open apex and necrotic pulps. Clinical and radiographic controls were made to observe foraminal closure. After that, the root canals were filled, employing the conventional technique with gutta-percha cones and zinc oxide eugenol cements. The calcium hydroxide paste was applied in the apical region before the root canal filling. The follow-up was done periodically and the cases have more than two years of control. (author) [pt

Inhibition of Apical Root Resorption by Calcium Hydroxide During Orthodontic Treatment: A Case Report

OpenAIRE

Pacheco, Cinthia Mara da Fonseca; Pacheco, Daniela da Fonseca; Motta, Patrícia Gonçalves da

2016-01-01

Apical root resorption is a common outcome of orthodontic treatment. The present article reports a case of absence of apical root resorption in a left maxillary lateral incisor filled with calcium hydroxide paste throughout orthodontic movement. After orthodontic treatment was completed the tooth was subsequently obturatedwith gutta-percha and the patient followed for 18 months. The presence of a periapical lesion and the properties of calcium hydroxide as a root resorption inhibitor were dec...

Calcium hydroxide induced apexification with apical root development: a clinical case report.

Science.gov (United States)

Soares, J; Santos, S; César, C; Silva, P; Sá, M; Silveira, F; Nunes, E

2008-08-01

To report the induction of apical root development by calcium hydroxide in teeth with pulp necrosis and periapical radiolucency. A 10-year-old male patient was admitted to the clinic complaining of an intense pain and oedema on the anterior facial region, compatible with an acute dentoalveolar abscess. There was a previous history of dental trauma; only tooth 11 was negative to pulp sensitivity tests. Radiographically, tooth 11 exhibited incomplete root formation, characterized by a wide root canal, thin and fragile dentinal walls, and an extensive, divergent foraminal opening associated with an apical radiolucency. The first appointment focused on urgent local and systemic treatment. Apexification treatment commenced at the second session after 7 days, by means of chemo-mechanical debridement throughout the entire root canal, using K-files and irrigation with a 2.5% sodium hypochlorite solution. Subsequently, a calcium hydroxide paste was applied and changed four times over 8 months, when radiographic examination revealed complete closure of the foraminal opening, resulting in resolution of the periapical radiolucency and associated with 5 mm of additional root development. The root canal was filled by thermomechanical compaction of gutta-percha and sealer. A 3-year follow-up revealed normal periapical tissues and the absence of symptoms. * In young patients, dental trauma may cause pulp necrosis and arrest of root formation. * Under certain circumstances, chemo-mechanical debridement, including the use of a calcium hydroxide paste, is a valid alternative to mineral trioxide aggregate and or surgery for root-end closure. * In teeth with incompletely formed roots associated with periapical lesions, calcium hydroxide can induce periapical repair through the closure of the foramen and apical root development.

The effect of calcium hydroxide treatment on the nutritive and feeding value of Albizia procera for growing goats

Energy Technology Data Exchange (ETDEWEB)

Alam, M.R. [Department of Animal Science, Bangladesh Agricultural University, Mymensingh (Bangladesh)]. E-mail: mralam@royalten.net.bd; Kabir, A.K.M.A.; Amin, M.R. [Department of Animal Science, Bangladesh Agricultural University, Mymensingh (Bangladesh); McNeill, D.M. [Faculty of Veterinary Science, University of Sydney, Camden, NSW (Australia)

2005-08-19

Albizia procera (Albizia) is widely planted in Bangladesh for timber and the leaves are also used as forage. In the dry season the leaves are less palatable than in the wet season and this may be a consequence of an excessive content of tannin. Albizia foliage was collected in the wet (June) and dry (January) seasons from six agro-ecological zones across Bangladesh and chemical composition, for tannins in particular, was determined. Variation in the tannin content across the six zones proved to be minimal. However, the concentration of tannins was almost two-fold higher in the dry compared to the wet season. To assess the potential for deactivating the tannins in Albizia so as to improve its nutritive value, leaves were treated with alkali (either calcium hydroxide or potassium carbonate) or polyethylene glycol (PEG). Alkali treatment reduced the concentrations of extractable tannin by as much as 92%. The ability of calcium hydroxide to deactivate tannin was then tested in vivo. Young goats, fed a basal diet of hay and wheat bran, were allocated to 4 equal groups (n = 4 per group) and supplemented with fresh Albizia foliage (at 300 g/kg of the diet) that was either untreated, or treated with either PEG, calcium hydroxide or calcium hydroxide + PEG. The supplements were fed daily for 9 weeks to allow the effects of chemical treatment on intake and growth rate to be defined. In vivo digestibility, nitrogen (N) balance, and microbial N supply were measured over the 5th week. Intakes of feed dry matter (DM) and the digestibility of DM were similar across treatments (mean intake 32 g/(kg LW day), mean DM digestibility 0.63). However, both the PEG and the PEG + calcium hydroxide treatments, compared to the control and calcium hydroxide only treatments, increased N digestibility (0.72, 0.70 versus 0.60, 0.61), N retention (0.43, 0.48 mg N/mg versus 0.26, 0.27 mg N/mg N intake), and microbial N supply (23.7, 21.4 g/day versus 14.2, 12.4 g/day). These increases translated

The effect of calcium hydroxide treatment on the nutritive and feeding value of Albizia procera for growing goats

International Nuclear Information System (INIS)

Alam, M.R.; Kabir, A.K.M.A.; Amin, M.R.; McNeill, D.M.

2005-01-01

Albizia procera (Albizia) is widely planted in Bangladesh for timber and the leaves are also used as forage. In the dry season the leaves are less palatable than in the wet season and this may be a consequence of an excessive content of tannin. Albizia foliage was collected in the wet (June) and dry (January) seasons from six agro-ecological zones across Bangladesh and chemical composition, for tannins in particular, was determined. Variation in the tannin content across the six zones proved to be minimal. However, the concentration of tannins was almost two-fold higher in the dry compared to the wet season. To assess the potential for deactivating the tannins in Albizia so as to improve its nutritive value, leaves were treated with alkali (either calcium hydroxide or potassium carbonate) or polyethylene glycol (PEG). Alkali treatment reduced the concentrations of extractable tannin by as much as 92%. The ability of calcium hydroxide to deactivate tannin was then tested in vivo. Young goats, fed a basal diet of hay and wheat bran, were allocated to 4 equal groups (n = 4 per group) and supplemented with fresh Albizia foliage (at 300 g/kg of the diet) that was either untreated, or treated with either PEG, calcium hydroxide or calcium hydroxide + PEG. The supplements were fed daily for 9 weeks to allow the effects of chemical treatment on intake and growth rate to be defined. In vivo digestibility, nitrogen (N) balance, and microbial N supply were measured over the 5th week. Intakes of feed dry matter (DM) and the digestibility of DM were similar across treatments (mean intake 32 g/(kg LW day), mean DM digestibility 0.63). However, both the PEG and the PEG + calcium hydroxide treatments, compared to the control and calcium hydroxide only treatments, increased N digestibility (0.72, 0.70 versus 0.60, 0.61), N retention (0.43, 0.48 mg N/mg versus 0.26, 0.27 mg N/mg N intake), and microbial N supply (23.7, 21.4 g/day versus 14.2, 12.4 g/day). These increases translated

Flare-ups incidence and severity after using calcium hydroxide as intracanal dressing.

Science.gov (United States)

Ghoddusi, Jamileh; Javidi, Maryam; Zarrabi, Mohammad Hasan; Bagheri, Hossein

2006-01-01

Acute pain and swelling following endodontic treatment are a challenge for both the patient and the dentist. According to previous studies, the incidence of flare-ups increases after endodontic treatment of teeth with necrotic pulps. Calcium hydroxide is currently used as a multi-purpose drug in root canal therapy. The aim of this study was to evaluate the incidence and severity of flare-ups after treatment of pulpless teeth using calcium hydroxide as an intracanal dressing. Sixty patients with single-root necrotic teeth participated in this study. These patients were randomly divided into three groups of 20. The patients were treated in Group A in a single-visit approach, in group B with a two-visit approach without any intracanal dressing and group C with a two-visit approach using calcium hydroxide as an intracanal dressing for one week. All of the patients were followed for 72 hours after each treatment session. The information about the incidence and severity of pain and swelling was recorded in tables, using a modified Visual Analogue Scale for pain severity measurement and a scale with four degrees for measuring the severity of swelling. The data were analyzed by chi-square test and GENMODE procedure.

Evaluation of interference of calcium hydroxide-based intracanal medication in filling root canal systems.

Science.gov (United States)

Vilela, Deyla Duarte; Neto, Manoel Matos; Villela, Alexandre Mascarenhas; Pithon, Matheus Melo

2011-09-01

To evaluate the interference of the intracanal medication Calen® (SSWhite, Sao Paulo, Brazil) on the filling of simulated lateral canals. Twenty human anterior teeth were used. Before the endodontic filling procedures the access of cavity was made, and after this root canals were made in all the teeth to simulate the presence of lateral canals. After preparation, the teeth were randomly divided into two groups (n=10). In group I, the root canal system was filled directly after chemicalmechanical preparation; in group II, endodontic treatment was performed in multiple sessions, and after preparation the calcium hydroxide-based intracanal medication Calen® was inserted. After the period of 7 days, the root canals were vigorously irrigated and then they were filled. Next, the teeth were radiographed to verify the quality of the filling. The results demonstrated that the teeth treated in a single session, without calcium hydroxide medication, presented 47 canals out of 60 with radiographic evidence of filling, whereas the teeth in which intracanal medication was used, only 07 presented a radiographic image compatible with filling (p < 0.05). The use of the calcium hydroxide-based medication Calen made it difficult to obtain a hermetic filling of the root canal system. The clinical significance of this work basing on the fact that once the dentist knowing that property obliteration of calcium hydroxide can be taken care when they are used in the presence of lateral canals.

Mixing Acid Salts and Layered Double Hydroxides in Nanoscale under Solid Condition.

Science.gov (United States)

Nakayama, Hirokazu; Hayashi, Aki

2014-07-30

The immobilization of potassium sorbate, potassium aspartate and sorbic acid in layered double hydroxide under solid condition was examined. By simply mixing two solids, immobilization of sorbate and aspartate in the interlayer space of nitrate-type layered double hydroxide, so called intercalation reaction, was achieved, and the uptakes, that is, the amount of immobilized salts and the interlayer distances of intercalation compounds were almost the same as those obtained in aqueous solution. However, no intercalation was achieved for sorbic acid. Although intercalation of sorbate and aspartate into chloride-type layered double hydroxide was possible, the uptakes for these intercalation compounds were lower than those obtained using nitrate-type layered double hydroxide. The intercalation under solid condition could be achieved to the same extent as for ion-exchange reaction in aqueous solution, and the reactivity was similar to that observed in aqueous solution. This method will enable the encapsulation of acidic drug in layered double hydroxide as nano level simply by mixing both solids.

Mixing Acid Salts and Layered Double Hydroxides in Nanoscale under Solid Condition

Directory of Open Access Journals (Sweden)

Hirokazu Nakayama

2014-07-01

Full Text Available The immobilization of potassium sorbate, potassium aspartate and sorbic acid in layered double hydroxide under solid condition was examined. By simply mixing two solids, immobilization of sorbate and aspartate in the interlayer space of nitrate-type layered double hydroxide, so called intercalation reaction, was achieved, and the uptakes, that is, the amount of immobilized salts and the interlayer distances of intercalation compounds were almost the same as those obtained in aqueous solution. However, no intercalation was achieved for sorbic acid. Although intercalation of sorbate and aspartate into chloride-type layered double hydroxide was possible, the uptakes for these intercalation compounds were lower than those obtained using nitrate-type layered double hydroxide. The intercalation under solid condition could be achieved to the same extent as for ion-exchange reaction in aqueous solution, and the reactivity was similar to that observed in aqueous solution. This method will enable the encapsulation of acidic drug in layered double hydroxide as nano level simply by mixing both solids.

Production of calcium hydroxide from the waste of Cariri stone

International Nuclear Information System (INIS)

Alves, T.M.E.; Santos, A.M.M.; Brasileiro, M.I.; Pinheiro, S.F.L.; Prado, A.C.A.

2016-01-01

The extraction of Cariri stone in the northeast is a frequent activity because of its ornamental application as well as for the construction sector. However, by this extraction, untapped waste formation grows and becomes a problem for the environment. The objective of this work is to produce calcium hydroxide, from this limestone residue, with controlled porosity, solubility and particle size. The waste was characterized with X-Ray Diffraction (XRD), X-Ray Fluorescence (XRF) and thermal analysis (TGA). The limestone was calcined at 850°C and 950°C for 45 minutes and three hours, being characterized by XRD, XRF and TGA. Once calcined, it was hydrated with 17,5g and 22g oxide to 100mL water and manually mixed for 15 and 25 minutes. The calcium hydroxides have been submitted for tests in vivo in rats and will be characterized by XRD, Scanning Electron Microscopy (SEM) and Infrared. (author)

Efficacy of NiTi rotary instruments in removing calcium hydroxide dressing residues from root canal walls

Directory of Open Access Journals (Sweden)

Milton Carlos Kuga

2012-02-01

Full Text Available The aim of this study was to evaluate the efficacy of three rotary instrument systems (K3, ProTaper and Twisted File in removing calcium hydroxide residues from root canal walls. Thirty-four human mandibular incisors were instrumented with the ProTaper System up to the F2 instrument, irrigated with 2.5% NaOCl followed by 17% EDTA, and filled with a calcium hydroxide intracanal dressing. After 7 days, the calcium hydroxide dressing was removed using the following rotary instruments: G1 - NiTi size 25, 0.06 taper, of the K3 System; G2 - NiTi F2, of the ProTaper System; or G3 - NiTi size 25, 0.06 taper, of the Twisted File System. The teeth were longitudinally grooved on the buccal and lingual root surfaces, split along their long axis, and their apical and cervical canal thirds were evaluated by SEM (×1000. The images were scored and the data were statistically analyzed using the Kruskall Wallis test. None of the instruments removed the calcium hydroxide dressing completely, either in the apical or cervical thirds, and no significant differences were observed among the rotary instruments tested (p > 0.05.

Antimicrobial Activity and Physicochemical Properties of Calcium Hydroxide Pastes Used as Intracanal Medication.

Science.gov (United States)

Zancan, Rafaela Fernandes; Vivan, Rodrigo Ricci; Milanda Lopes, Marcelo Ribeiro; Weckwerth, Paulo Henrique; de Andrade, Flaviana Bombarda; Ponce, José Burgos; Duarte, Marco Antonio Hungaro

2016-12-01

The aim of the present study was to evaluate the pH, calcium release, solubility, and antimicrobial action against biofilms of calcium hydroxide + saline solution, Calen (SS White Artigos Dentários Ltd, Rio de Janeiro, Brazil) (CH/P), Calen camphorated paramonochlorophenol (CMCP) (CH/CMPC), and calcium hydroxide + chlorhexidine (CH/CHX) pastes. The pH of the pastes was determined with a calibrated pH meter placed in direct contact with each paste. The root canals of acrylic teeth (N = 10) were filled with the previously mentioned intracanal dressings and immersed in ultrapure water to measure hydroxyl (pH meter) and calcium ion release (atomic absorption spectrophotometer) at time intervals of 3, 7, 15, and 30 days. To assess solubility, the root canals of acrylic teeth (N = 10) were filled with the previously mentioned pastes and scanned by micro-computed tomographic imaging before (initial) and after 7, 15, and 30 days of immersion in ultrapure water. The solubility of each specimen was the difference between the initial and final volume scanning. For antimicrobial analysis, monospecies and dual-species biofilms were in vitro induced on dentin blocks (N = 20). Afterward, they were treated with the pastes for 7 days. Live/dead dye and a confocal microscope were used to measure the percentage of living cells. Data were statistically compared (P calcium hydroxide + saline solution, CH/P, and CH/CMCP pastes to kill bacterial cells in the biofilms studied. Chlorhexidine added to CH favored greater effectiveness against the previously mentioned bacterial biofilms. Copyright © 2016 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Effects of irrigation solutions and Calcium hydroxide dressing on root canal treatments of periapical lesions

Directory of Open Access Journals (Sweden)

Vita Nirmala

2006-03-01

Full Text Available The preparation of root canal in endodontic treatment plays an important role in treating non vital teeth with periapical lesion. Some factors influence the success of root canal treatment in short and long terms are the irrigation of root canal using antiseptic solution and the use of root canal medicament. The aim of this literature study is to determined the effect of irrigation solution and Calcium hydroxide dressing in root canal treatment of periapical lesions. The use of root canal medicament during the endodontic treatment could sterilized and decreased the number of pathogenic microorganism of root canal. An effective root canal irrigation solution must be able to dissolve organic and anorganic debris, lubricate endodontic instruments, disinfect microorganisms, non toxic and economical. The best irrigation solution has maximum antimicrobial effect with minimum toxicity. Division of calcium hydroxide into Calcium and hydroxyl ions is responsible for alkalinization of cavity, subsequently it makes the condition of cavity to be inappropriate for bacterial endotoxin in vitro as well as in vivo, and considered as the only clinically effective medicament in inactivating bacterial endotoxin. Calcium hydroxide is the only medication which has the ability to clinically inactive bacterial endotoxin in vitro in vivo and accepted as the best of root canal medication.

Impact analysis of calcium hydroxide on the juveniles of the river ...

African Journals Online (AJOL)

The use of inorganic chemicals to boost agro production has recently been extended to other environmental purposes. This study thus was carried out to assess the potential lethal impact of calcium hydroxide (Ca (OH)2) on aquatic environment using the brackish river prawn as the indicator organism. The prawns were ...

Calcium and lanthanum solid base catalysts for transesterification

Science.gov (United States)

Ng, K. Y. Simon; Yan, Shuli; Salley, Steven O.

2015-07-28

In one aspect, a heterogeneous catalyst comprises calcium hydroxide and lanthanum hydroxide, wherein the catalyst has a specific surface area of more than about 10 m.sup.2/g. In another aspect, a heterogeneous catalyst comprises a calcium compound and a lanthanum compound, wherein the catalyst has a specific surface area of more than about 10 m.sup.2/g, and a total basicity of about 13.6 mmol/g. In further another aspect, a heterogeneous catalyst comprises calcium oxide and lanthanum oxide, wherein the catalyst has a specific surface area of more than about 10 m.sup.2/g. In still another aspect, a process for preparing a catalyst comprises introducing a base precipitant, a neutral precipitant, and an acid precipitant to a solution comprising a first metal ion and a second metal ion to form a precipitate. The process further comprises calcining the precipitate to provide the catalyst.

Calcium Hydroxide-induced Proliferation, Migration, Osteogenic Differentiation, and Mineralization via the Mitogen-activated Protein Kinase Pathway in Human Dental Pulp Stem Cells.

Science.gov (United States)

Chen, Luoping; Zheng, Lisha; Jiang, Jingyi; Gui, Jinpeng; Zhang, Lingyu; Huang, Yan; Chen, Xiaofang; Ji, Jing; Fan, Yubo

2016-09-01

Calcium hydroxide has been extensively used as the gold standard for direct pulp capping in clinical dentistry. It induces proliferation, migration, and mineralization in dental pulp stem cells (DPSCs), but the underlying mechanisms are still unclear. The aim of this study was to investigate the role of the mitogen-activated protein (MAP) kinase pathway in calcium hydroxide-induced proliferation, migration, osteogenic differentiation, and mineralization in human DPSCs. Human DPSCs between passages 3 and 6 were used. DPSCs were preincubated with inhibitors of MAP kinases and cultured with calcium hydroxide. The phosphorylated MAP kinases were detected by Western blot analysis. Cell viability was analyzed via the methylthiazol tetrazolium assay. Cell migration was estimated using the wound healing assay. Alkaline phosphatase (ALP) expression was analyzed using the ALP staining assay. Mineralization was studied by alizarin red staining analysis. Calcium hydroxide significantly promoted the phosphorylation of the c-Jun N-terminal kinase (JNK), p38, and extracellular signal-regulated kinase. The inhibition of JNK and p38 signaling abolished calcium hydroxide-induced proliferation of DPSCs. The inhibition of JNK, p38, and extracellular signal-regulated kinase signaling suppressed the migration, ALP expression, and mineralization of DPSCs. Our study showed that the MAP kinase pathway was involved in calcium hydroxide-induced proliferation, migration, osteogenic differentiation, and mineralization in human DPSCs. Copyright © 2016 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Early age hydration of calcium sulfoaluminate (synthetic ye'elimite, ) in the presence of gypsum and varying amounts of calcium hydroxide

KAUST Repository

Hargis, Craig W.; Kirchheim, Ana Paula; Monteiro, Paulo J.M.; Gartner, Ellis M.

2013-01-01

Suspensions of synthetic ye'elimite (C4A3S̄) in a saturated gypsum (CS̄H2) and calcium hydroxide (CH) solution were examined in-situ in a wet cell by soft X-ray transmission microscopy and ex-situ by scanning electron microscopy. The most voluminous hydration product observed was ettringite. Ettringite commonly displayed acicular, filiform, reticulated, and stellate crystal habits. Additionally, pastes with C 4A3S̄, 15% CS̄H2, and varying amounts of CH were prepared and examined with X-ray diffraction (XRD) and isothermal calorimetry. The XRD experiments showed that increasing CH content caused more solid solution (SO4 2 -/OH-) AFm phases to form at early ages (< 1 d) and more monosulfate to form at later ages (> 1 d). Calorimetry indicated that the increased production of solid solution AFm was accompanied with an increase in the initial (< 30 min) rate of heat evolution, and increasing CH generally reduced the time till the second maximum rate of heat evolution due to the formation of ettringite and monosulfate. © 2013 Elsevier Ltd.

Early age hydration of calcium sulfoaluminate (synthetic ye'elimite, ) in the presence of gypsum and varying amounts of calcium hydroxide

KAUST Repository

Hargis, Craig W.

2013-06-01

Suspensions of synthetic ye\\'elimite (C4A3S̄) in a saturated gypsum (CS̄H2) and calcium hydroxide (CH) solution were examined in-situ in a wet cell by soft X-ray transmission microscopy and ex-situ by scanning electron microscopy. The most voluminous hydration product observed was ettringite. Ettringite commonly displayed acicular, filiform, reticulated, and stellate crystal habits. Additionally, pastes with C 4A3S̄, 15% CS̄H2, and varying amounts of CH were prepared and examined with X-ray diffraction (XRD) and isothermal calorimetry. The XRD experiments showed that increasing CH content caused more solid solution (SO4 2 -/OH-) AFm phases to form at early ages (< 1 d) and more monosulfate to form at later ages (> 1 d). Calorimetry indicated that the increased production of solid solution AFm was accompanied with an increase in the initial (< 30 min) rate of heat evolution, and increasing CH generally reduced the time till the second maximum rate of heat evolution due to the formation of ettringite and monosulfate. © 2013 Elsevier Ltd.

Efficacy of calcium oxide and calcium hydroxide nanoparticles on the elimination of Enterococcus faecalis in human root dentin.

Science.gov (United States)

Louwakul, Phumisak; Saelo, Attapon; Khemaleelakul, Saengusa

2017-04-01

The objective of this study was to compare the antibacterial effect of calcium oxide nanoparticles (CONPs) and calcium hydroxide nanoparticles (CHNPs) against Enterococcus faecalis in a dentinal block model. E. faecalis strain JCM 7783 was introduced into dentinal tubules of semicylindrical dentin specimens by centrifugation and incubated for 1 week. Fifty microliters of CONPs or CHNPs was placed on the root canal side of the infected dentin specimens. The specimens were then incubated in aerobic condition at 37 °C and 100 % relative humidity for 1 week. The treated dentin specimens were subjected to fluorescent staining and confocal laser scanning microscopy (CLSM) to analyze the proportions of non-vital and vital bacterial cells inside the dentinal tubules. Scanning electron microscopy (SEM) was used to confirm the effect of the medicaments on the bacteria in the dentinal tubules. Calcium oxide (CO) and calcium hydroxide (CH) were used as controls. Based on the CLSM and SEM analyses, CHNPs were more efficient than CONPs in the elimination of the bacteria in the dentinal tubules. CONPs significantly killed more E. faecalis than CO and CH (P < .05). Neither CO nor CH was able to kill the bacteria. CHNPs were more effective than CONPs in the elimination of E. faecalis in dentinal tubules. CHNPs are effective nanoparticles in killing endodontic bacteria present in dentinal tubules. They have potential as an intracanal medicament, which may be beneficial in root canal therapy.

Improving the quality of rice straw by urea and calcium hydroxide on rumen ecology, microbial protein synthesis in beef cattle.

Science.gov (United States)

Polyorach, S; Wanapat, M

2015-06-01

Four rumen-fistulated beef cattle were randomly assigned to four treatments according to a 4 × 4 Latin square design to study the influence of urea and calcium hydroxide [Ca(OH)2 ] treatment of rice straw to improve the nutritive value of rice straw. Four dietary treatments were as follows: untreated rice straw, 50 g/kg urea-treated rice straw, 20 g/kg urea + 20 g/kg calcium hydroxide-treated rice straw and 30 g/kg urea + 20 g/kg calcium hydroxide-treated rice straw. All animals were kept in individual pens and fed with concentrate at 0.5 g/kg of BW (DM), rice straw was fed ad libitum. The experiment was conducted for four periods, and each period lasted for 21 days. During the first 14 days, DM feed intake measurements were made while during the last 7 days, all cattle were moved to metabolism crates for total faeces and urine collections. The results revealed that 20 g/kg urea + 20 g/kg calcium hydroxide-treated rice straw improved the nutritive value of rice straw, in terms of dry matter intake, digestibility, ruminal volatile fatty acids, population of bacteria and fungi, nitrogen retention and microbial protein synthesis. Based on this study, it could be concluded that using urea plus calcium hydroxide was one alternative method to improve the nutritive value of rice straw, rumen ecology and fermentation and thus a reduction of treatment cost. Journal of Animal Physiology and Animal Nutrition © 2014 Blackwell Verlag GmbH.

Pulp revascularization after root canal decontamination with calcium hydroxide and 2% chlorhexidine gel.

Science.gov (United States)

Soares, Adriana de Jesus; Lins, Fernanda Freitas; Nagata, Juliana Yuri; Gomes, Brenda Paula Figueiredo de Almeida; Zaia, Alexandre Augusto; Ferraz, Caio Cezar Randi; de Almeida, José Flávio Affonso; de Souza-Filho, Francisco José

2013-03-01

Pulp revascularization may be considered a promising alternative for necrotic immature teeth. Many studies have accomplished passive decontamination associated with an antibiotic paste. To date, there is no report evaluating calcium hydroxide associated with 2% chlorhexidine gel for revascularization therapy. The aim of this case report was to describe a new proposal for pulp revascularization with mechanical decontamination and intracanal medication composed of calcium hydroxide and 2% chlorhexidine gel. The patient, a 9-year-old girl, suffered an intrusion associated with pulp exposure caused by an enamel-dentin fracture in her maxillary left central incisor. After diagnosis, treatment consisted of revascularization therapy with gentle manual instrumentation of the cervical and medium thirds of the root in addition to intracanal medication with calcium hydroxide and 2% chlorhexidine gel for 21 days. In the second session, a blood clot was stimulated up to the cervical third of the root canal. Mineral trioxide aggregate (MTA; Angelus, Londrina, Paraná, Brazil) was used for cervical sealing of the canal. Coronal sealing was performed with temporary filling material and composite resin. During the follow-up period, the root canal space showed a progressive decrease in width, mineralized tissue deposition on root canal walls, and apical closure. A cone-beam computed tomography scan taken at the 2-year follow-up confirmed these findings and did not show complete root canal calcification. This new proposal for revascularization therapy with 2% chlorhexidine gel may be used for the treatment of necrotic immature root canals. Copyright © 2013 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Mixing Acid Salts and Layered Double Hydroxides in Nanoscale under Solid Condition

OpenAIRE

Nakayama, Hirokazu; Hayashi, Aki

2014-01-01

The immobilization of potassium sorbate, potassium aspartate and sorbic acid in layered double hydroxide under solid condition was examined. By simply mixing two solids, immobilization of sorbate and aspartate in the interlayer space of nitrate-type layered double hydroxide, so called intercalation reaction, was achieved, and the uptakes, that is, the amount of immobilized salts and the interlayer distances of intercalation compounds were almost the same as those obtained in aqueous solution...

Preparation of hydroxide ion conductive KOH–layered double hydroxide electrolytes for an all-solid-state iron–air secondary battery

Directory of Open Access Journals (Sweden)

Taku Tsuneishi

2014-06-01

Full Text Available Anion conductive solid electrolytes based on Mg–Al layered double hydroxide (LDH were prepared for application in an all-solid-state Fe–air battery. The ionic conductivity and the conducting ion species were evaluated from impedance and electromotive force measurements. The ion conductivity of LDH was markedly enhanced upon addition of KOH. The electromotive force in a water vapor concentration cell was similar to that of an anion-conducting polymer membrane. The KOH–LDH obtained was used as a hydroxide ion conductive electrolyte for all-solid-state Fe–air batteries. The cell performance of the Fe–air batteries was examined using a mixture of KOH–LDH and iron-oxide-supported carbon as the negative electrode.

Diode Laser and Calcium Hydroxide for Elimination of Enterococcus Faecalis in Root Canal

Directory of Open Access Journals (Sweden)

Neda Naghavi

2014-06-01

Full Text Available Introduction: The ultimate goal of endodontic treatment is to eliminate the bacterial infection in the root canal system. While mechanical debridement combined with chemical irrigation removes the bulk of microorganisms, residual bacteria are readily detectable in approximately one-half of teeth just prior to obturation. Laser light can be used to destroy bacteria. This in vitro study was performed to evaluate the effect of diode laser and calcium hydroxide on mono-infected dental canals.Methods: Fifty five single-rooted human premolars were prepared and contaminated with Enterococcus faecalis. After three weeks of incubation, the samples were divided into three experimental groups (n = 15 and two control groups (n = 5. In the first and second groups, the teeth were rinsed for 5 min with either sterile saline or 5.25% NaOCl and irradiated with a 810-nm diode laser at 1.5 W output for 5 × 4s. In the third group, the teeth were rinsed with 5.25% NaOCl and then Ca(OH2 paste was inserted in the canals for 1 week. Intracanal bacterial sampling was done and the samples were plated to determine the CFU count. Results: 5.25% NaOCl plus laser was as effective as calcium hydroxide and significantly more effective than sterile saline (P>0.05 in elimination of E. faecalis. Complete elimination of E. faecalis was seen only for the one week calcium hydroxide treatment. Conclusion: Combination therapy with NaOCl irrigation and diode laser irradiation can be recommended as an effective treatment option for elimination of E. faecalis from the root canal system.

Evaluation of permeability and swelling pressure of compacted bentonite using a calcium hydroxide solution

International Nuclear Information System (INIS)

Aoyagi, Takayoshi; Maeda, Munehiro; Mihara, Morihiro; Tanaka, Masuhiro

1998-12-01

Tests to determine the swelling pressure, permeability, compressive strength and elastic modulus of Ca-Na exchanged bentonite, Na-bentonite and Ca-bentonite at the Power Reactor and Nuclear Fuel Development Corporation have mainly used distilled water. However, disposal facilities for TRU waste will use cementateous material for packaging, backfill as well as structural support. In this case, a large amount of calcium will dissolve in groundwater flowing through the cementateous material. Therefore, it is important to investigate the mechanical properties of bentonite in calcium-rich water as part of the disposal research program for TRU waste. In order to understand the effect of the chemical composition of water on the basic mechanical properties of bentonite - part of evaluating the disposal concepts for TRU waste disposal - we tested the permeability of compacted bentonite under saturated conditions using a calcium hydroxide solution. The aqueous solution represents water dominated by the calcium component. Na-bentonite, Ca-Na exchanged bentonite and Ca-bentonite were used for swelling pressure measurement tests and permeability testing. Measures of the maximum and equilibrium swelling pressure as well as permeability we obtained. The dry density of bentonite was varied between tests. Results show that swelling pressure and permeability are dependent on dry density. In separate tests using Ca-bentonite, the bentonite-mixing rate was varied as an independent parameter. Results show that there is little change in the swelling pressure and permeability between tests using calcium hydroxide solution and distilled water for all bentonite types. (author)

Diffusion of hydroxyl ions from calcium hydroxide and Aloe vera pastes.

Science.gov (United States)

Batista, Victor Eduardo de Souza; Olian, Douglas Dáquila; Mori, Graziela Garrido

2014-01-01

This study evaluated the diffusion through the dentinal tubules of hydroxyl ions from different calcium hydroxide (CH) pastes containing Aloe vera. Sixty single-rooted bovine teeth were used. The tooth crowns were removed, the root canals were instrumented and the specimens were assigned to 4 groups (n=15) according to the intracanal medication: Group CH/S - CH powder and saline paste; Group CH/P - CH powder and propylene glycol paste; Group CH/A - calcium hydroxide powder and Aloe vera gel paste; Group CH/A/P - CH powder, Aloe vera powder and propylene glycol paste. After placement of the root canal dressings, the teeth were sealed coronally and apically with a two-step epoxy adhesive. The teeth were placed in identified flasks containing deionized water and stored in an oven with 100% humidity at 37 °C. After 3 h, 24 h, 72 h, 7 days, 15 days and 30 days, the deionized water in the flasks was collected and its pH was measured by a pH meter. The obtained data were subjected to statistical analysis at a significance level of 5%. The results demonstrated that all pastes provided diffusion of hydroxyl ions through the dentinal tubules. The combination of Aloe vera and CH (group CH/A) provided a constant release of calcium ions. Group CH/A/P showed the highest pH at 24 and 72 h. In conclusion, the experimental pastes containing Aloe vera were able to enable the diffusion of hydroxyl ions through the dentinal tubules.

Magnesium hydroxide as the neutralizing agent for radioactive hydrochloric acid solutions

International Nuclear Information System (INIS)

Palmer, M.J.; Fife, K.W.

1995-10-01

The current technology at Los Alamos for removing actinides from acidic chloride waste streams is precipitation with approximately 10 M potassium hydroxide. Although successful, there are many inherent drawbacks to this precipitation technique which will be detailed in this paper. Magnesium hydroxide (K sp = 1.3 x 10 -11 ) has limited solubility in water and as a result of the common ion effect, cannot generate a filtrate with a pH greater than 9. At a pH of 9, calcium (K sp = 5.5 x 10 -6 ) will not coprecipitate as the hydroxide. This is an important factor since many acidic chloride feeds to hydroxide precipitation contain significant amounts of calcium. In addition, neutralization with Mg(OH) 2 produces a more filterable precipitate because neutralization occurs as the Mg(OH) 2 is dissolved by the acid rather than as a result of the much faster liquid/liquid reaction of KOH with the waste acid. This slower solid/liquid reaction allows time for crystal growth to occur and produces more easily filterable precipitates. On the other hand, neutralization of spent acid with strong KOH that yields numerous hydroxide ions in solution almost instantaneously forming a much larger volume of small crystallites that result in gelatinous, slow-filtering precipitates. Magnesium hydroxide also offers a safety advantage. Although mildly irritating, it is a weak base and safe and easy to handle. From a waste minimization perspective, Mg(OH) 2 offers many advantages. First, the magnesium hydroxide is added as a solid. This step eliminates the diluent water used in KOH neutralizations. Secondly, because the particle size of the precipitate is larger, more actinides are caught on the filter paper resulting in a smaller amount of actinide being transferred to the TA-50 Liquid Waste Treatment Facility. Third, the amount of solids that must be reprocessed is significantly smaller resulting in less waste generation from the downstream processes

Apexification of an Immature Permanent Incisor with the Use of Calcium Hydroxide: 16-Year Follow-Up of a Case

Directory of Open Access Journals (Sweden)

Camila Maggi Maia Silveira

2015-01-01

Full Text Available Apexification is a process of forming a mineralized apical barrier and had been performed by using calcium hydroxide paste, due to its biological and healing performances in cases of existent trauma. This clinical report aims to report the results of a 16-year follow-up study of an apexification treatment applied to nonvital tooth 22 of a healthy 8-year-old male after a trauma. Clinical inspection of the tooth showed fractures of the incisal edge and mesial angle, absence of coronal mobility, and negative pulp vitality under cold testing. Radiographic analysis of the root revealed incomplete apex formation. The possibility of fracture into the root or luxation injury was rejected, and the diagnosis of pulp necrosis was verified. Apexification by calcium hydroxide and subsequent endodontic treatment were planned. Initial formation of the mineralized apical barrier was observed after 3 months, and the barrier was considered to be completed after 8 months. Clinical, radiographic, and CBCT examinations after 16 years verified the success of the treatment, although the choice of calcium hydroxide for apexification treatment is discussed.

Radiopacity evaluation of root canal sealers containing calcium hydroxide and MTA

Directory of Open Access Journals (Sweden)

Juliane Maria Guerreiro- Tanomaru

2009-06-01

Full Text Available The purpose of this study was to evaluate the radiopacity of root canal sealers containing calcium hydroxide and MTA (Acroseal, Sealer 26, Sealapex, Endo CPM Sealer, Epiphany and Intrafill. Five disc-shaped specimens (10 x 1 mm were fabricated from each material, according to the ISO 6876/2001 standard. After setting of the materials, radiographs were taken using occlusal film and a graduated aluminum stepwedge varying from 2 to 16 mm in thickness. The dental X-ray unit (GE1000 was set at 50 kVp, 10 mA, 18 pulses/s and distance of 33.5 cm. The radiographs were digitized and the radiopacity compared to that of the aluminum stepwedge using VIXWIN-2000 software (Gendex. The data (mmAl were analyzed statistically by ANOVA and Tukey's test at the 5% significance level. Epiphany and Intrafill presented the highest radiopacity values (8.3 mmAl and 7.5 mmAl respectively, p < 0.05 followed by Sealer 26 (6.3 mmAl, Sealapex (6.1 mmAl and Endo CPM Sealer (6 mmAl. Acroseal was the least radiopaque material (4 mmAl, p < 0.05. In conclusion, the calcium hydroxide- and MTA-containing root canal sealers had different radiopacities. However, all materials presented radiopacity values above the minimum recommended by the ISO standard.

The calcium oxide influence on formation of manganese, calcium pyrovanadate solid solutions

International Nuclear Information System (INIS)

Vatolin, N.A.; Volkova, P.I.; Sapozhnikova, T.V.; Ovchinnikova, L.A.

1988-01-01

The X-ray graphic, derivatographic, microscopic and chemical methods are used to study solid solutions of manganese, calcium pyrovanadates containing 1-10 mass% CaO and the products of interaction of reprocessing charges of vanadium-containing converter slags intended for he formation of manganese and calcium pyrovanadates with additions of calcium oxide within 10-90 mass%. It is established that in the case of 1-6 mass% CaO content in manganese pyrovanadate solid interstitial solutions appear, while at 6-20 mass% CaO - solid substitution solutions form. The results of calculating elementary cell parameters as well as melting temperatures and pyrovanadate solid solution solubility depending on CaO content are presented. The best solubility of introduction solid solutions during vanadium extraction according to the lime technology is found

Effects of calcium hydroxide addition on the physical and chemical properties of a calcium silicate-based sealer.

Science.gov (United States)

Kuga, Milton Carlos; Duarte, Marco Antonio Hungaro; Sant'anna-Júnior, Arnaldo; Keine, Kátia Cristina; Faria, Gisele; Dantas, Andrea Abi Rached; Guiotti, Flávia Angélica

2014-06-01

Recently, various calcium silicate-based sealers have been introduced for use in root canal filling. The MTA Fillapex is one of these sealers, but some of its physicochemical properties are not in accordance with the ISO requirements. The aim of this study was to evaluate the flowability, pH level and calcium release of pure MTA Fillapex (MTAF) or containing 5% (MTAF5) or 10% (MTAF10) calcium hydroxide (CH), in weight, in comparison with AH Plus sealer. The flowability test was performed according to the ISO 6876:2001 requirements. For the pH level and calcium ion release analyses, the sealers were placed individually (n=10) in plastic tubes and immersed in deionized water. After 24 hours, 7 and 14 days, the water in which each specimen had been immersed was evaluated to determine the pH level changes and calcium released. Flowability, pH level and calcium release data were analyzed statistically by the ANOVA test (α=5%). In relation to flowability: MTAF>AH Plus>MTAF5>MTAF10. In relation to the pH level, for 24 h: MTAF5=MTAF10=MTAF>AH Plus; for 7 and 14 days: MTAF5=MTAF10>MTAF>AH Plus. For the calcium release, for all periods: MTAF>MTAF5=MTAF10>AH Plus. The addition of 5% CH to the MTA Fillapex (in weight) is an alternative to reduce the high flowability presented by the sealer, without interfering in its alkalization potential.

Accidental injury of the inferior alveolar nerve due to the extrusion of calcium hydroxide in endodontic treatment: a case report

Directory of Open Access Journals (Sweden)

Yooseok Shin

2016-02-01

Full Text Available During clinical endodontic treatment, we often find radiopaque filling material beyond the root apex. Accidental extrusion of calcium hydroxide could cause the injury of inferior alveolar nerve, such as paresthesia or continuous inflammatory response. This case report presents the extrusion of calcium hydroxide and treatment procedures including surgical intervention. A 48 yr old female patient experienced Calcipex II extrusion in to the inferior alveolar canal on left mandibular area during endodontic treatment. After completion of endodontic treatment on left mandibular first molar, surgical intervention was planned under general anesthesia. After cortical bone osteotomy and debridement, neuroma resection and neurorrhaphy was performed, and prognosis was observed. But no improvement in sensory nerve was seen following surgical intervention after 20 mon. A clinician should be aware of extrusion of intracanal medicaments and the possibility of damage on inferior alveolar canal. Injectable type of calcium hydroxide should be applied with care for preventing nerve injury. The alternative delivery method such as lentulo spiral was suggested on the posterior mandibular molar.

Leaching of both calcium hydroxide and C-S-H from cement paste: Modeling the mechanical behavior

International Nuclear Information System (INIS)

Carde, C.; Torrenti, J.M.; Francois, R.

1996-01-01

This paper deals with the effect of the leaching process of cement based materials on their mechanical properties. This process induces mainly a total leaching of Ca(OH) 2 and a progressive decalcification of C-S-H which leads to a gradient of C/S ratio in the leaching zone. In a previous work, the authors venture the hypothesis that the dissolution of calcium hydroxide was the essential parameter governing both decrease in strength and increase in porosity in the case of a paste sample made with an OPC cement which leads to a 20% content of calcium. In order to quantify the effect of the decrease of C/S ratio in C-S-H, the authors have performed experiments on paste samples with the admixture of silica fume to reduce the content of calcium hydroxide and thus emphasize the effect of C/S ratio decrease of the C-S-H. The leaching process was achieved by the use of a 50% concentrate solution of ammonium nitrate. Compression tests were conducted on micro-cylinder samples (10, 12, 14, 20 and 30 mm of diameter) because of the slow kinetics of degradation due to the leaching. The deterioration of the cement paste and the mortar exposed to the action of the ammonium nitrate was indicated by a peripheral zone of less resistance. The experimental results allow the modeling of the mechanical behavior of cement pastes in relation to the ratio of degraded area over total area of the sample A d /A t . The model thus defined allows separation of the effect of calcium hydroxide leaching and C-S-H leaching, and shows the importance of the first one. The current research program tries to characterize the deterioration of the mechanical properties of the concrete surrounding radioactive wastes, due to the water flow during storage

Development of composite calcium hydroxide sorbent in mechanical operations and evaluation of its basic sorption properties

Directory of Open Access Journals (Sweden)

Gara Paweł

2017-01-01

Full Text Available This article presents the results of research carried out on the possibility of obtaining composite calcium hydroxide sorbent in the process of two-step granulation, containing additional compounds of Al, Mg and Fe, and their textural and sorption studies. For this purpose, attempts were undertaken to compact commercial calcium hydroxide powder with six additives in the laboratory roll press. The resulting compacts were crushed and sieved in order to achieve the assumed sieve fraction. Based on the obtained results, basic parameters of the process of formation of composite sorbent have been determined. Both, the selected composite sorbents fractions and additives were subsequently subjected to textural studies (determination of the specific surface area and porosity and sorption capacity performance. In addition, for the better interpretation of the results, thermogravimetric studies were carried out both for the additives and composite sorbents, as well as the grain size distribution of the additives. The results of the physicochemical tests of the obtained composite sorbents were compared with analogic results from the study on fine-grained hydroxide sorbent without additives and carbonate sorbent. The presented results showed that in a two-step granulation process it is possible to obtain the granular Ca(OH2 sorbent, as well as composite sorbents possessing better SO2 sorption capacity in comparison to the powder Ca(OH2 and/or to the calcium carbonate sorbent. This can be attributed to the combination of capability of the sorbent to appropriate thermal decomposition and the formation of a group of pores in the range of 0.07-0.3 microns.

Layered Metal Hydroxides Containing Calcium and Their Structural Analysis

Energy Technology Data Exchange (ETDEWEB)

Kim, Tae Hyun; Heo, Il; Lee, Sung Han; Oh, Jae Min [College of Science and Technology, Yonsei University, Wonju (Korea, Republic of); Paek, Seung Min [Kyungpook National University, Daegu (Korea, Republic of); Park, Chung Berm; Choi, Ae Jin [National Institute of Horticultural and Herbal Science of R and D Eumseong (Korea, Republic of); Choy, Jin Ho [Ewha Womans University, Seoul (Korea, Republic of)

2012-06-15

Layered metal hydroxides (LMHs) containing calcium were synthesized by coprecipitation in solution having two different trivalent metal ions, iron and aluminum. Two mixed metal solutions (Ca{sup 2+}/Al{sup 3+} and Ca{sup 2+}/Fe{sup 3+} = 2/1) were added to sodium hydroxide solution and the final pH was adjusted to {approx}11.5 and {approx}13 for CaAl-and CaFe-LMHs. Powder X-ray diffraction (XRD) for the two LMH samples showed well developed (00l) diffractions indicating 2-dimensional crystal structure of the synthesized LMHs. Rietveld refinement of the X-ray diffraction pattern, the local structure analysis through X-ray absorption spectroscopy, and thermal analysis also confirmed that the synthesized precipitates show typical structure of LMHs. The chemical formulae, Ca{sub 2.04}Al{sub 1}(OH){sub 6}(NO{sub 3}){center_dot}5.25H{sub 2}O and Ca{sub 2.01}Fe{sub 1}(OH){sub 6}(NO{sub 3}){center_dot}4.75H{sub 2}O were determined by inductively coupled plasma-atomic emission spectroscopy (ICP-AES). Particle morphology and thermal behavior for the synthesized LMHs were examined by field emission scanning electron microscopy and thermogravimetric differential scanning calorimetry

Comparison of the removal of calcium hydroxide medicaments on the root canal treatment irrigated with manual and sonic agitation technique

Directory of Open Access Journals (Sweden)

Anna Muryani

2017-11-01

Full Text Available Introduction: Irrigation of the root canal system is an important part of the endodontic treatment principle which aims to improve the hygiene of the root canal system from any debris and medicament residue with the hydrodynamic system. Root irrigation technique can be done with the manual and sonic system by using 2.5% NaOCI irrigation solution. Calcium hydroxide is used as a medicament for root canal sterilization. Root canal treatment will fail due to the imperfect removal of calcium hydroxide residue. The objective of this research was to analyze the comparison of the removal of calcium hydroxide medicaments on the root canal treatment irrigated with manual and sonic agitation technique using 2.5% sodium hypochlorite solution. Methods: The methods used in this study was experimental laboratory. The sample used was 30 maxillary incisors. The teeth were then divided into two groups randomly, then the root canal preparation was done by the crown down technique with manual irrigation using 2.5% NaOCI solution. The radicular part of the teeth was then split longitudinally, given a standardized groove in the one-third of the apical part, then applied with water-solved calcium hydroxide. The teeth were unified afterwards by using flowable composites, then soaked in the artificial saliva at the temperature of 37ºC. The sample of the 1st group was irrigated by manual agitation technique, and the sample of the 2nd group 2 was irrigated by sonic agitation technique, then both were viewed by stereo microscope. The data results were analyzed by Kruskal-Wallis and Mann-Whitney tests. Results: The results of calcium hydroxide removal were different between the root canals that were irrigated using 2.5% sodium hypochlorite irrigation solution by manual agitation technique compared to the sonic agitation technique. Irrigation using 2.5% sodium hypochlorite irrigation solution with the sonic agitation techniques were proven to be more effective in lifting Ca

Potential of PIXE for the elemental analysis of calcium hydroxide used in dentistry

International Nuclear Information System (INIS)

Suciu, Ioana; Ionescu, Ecaterina; Bodnar, Dan; Preoteasa, Eugen A.; Gurban, Dan

2006-01-01

Calcium hydroxide is used in dentistry and generally shows a clinically acceptable biocompatibility. However various commercial assortments show differences in their clinical performances, suggesting that certain aspects of their action are not completely understood and pointing to the necessity of new investigation methods. We report a preliminary study on two types of calcium hydroxide products carried out by thick target PIXE with 3.0 MeV protons, aiming to assess the potential of this method for the analysis of such biomaterials used in endodontic dentistry. (Semi)quantitative analysis was performed by use of reference materials, and relative concentrations of elements with respect to Ca were determined with an accuracy of about 30%; tentative absolute concentrations were also estimated by using Ca as a reference element. In both formulations, a number of trace elements (Mn, Fe, Zn and Sr, and possibly Cu and Pb - probably impurities from the raw materials) were evidenced. These trace elements together with the Ba/Ca ratio are reliable fingerprints for the identification of the materials, and evidenced a different origin for the Ca(OH) 2 used in the two specimens. Possible applications of PIXE in dental research may bring relevant compositional insight, and further studies of such materials are suggested. (authors)

Calcium hydroxide as intracanal dressing for teeth with apical periodontitis

Directory of Open Access Journals (Sweden)

Sari Dewiyani

2011-03-01

Full Text Available Background: Root canal infection and periapical diseases are caused by bacteria and their products. Long term infection may spread bacteria throughout the root canal system. Apical periodontitis caused by infectious microbe that persistent in root canals can cause radiographic and histopathology periapical changes. Chemomechanical preparation and intracanal dressing then are recommended to be conducted and used in between visits to eliminate microbes in root canals. Calcium hydroxide (Ca(OH2 can be used as intracanal dressing since it can be used as musical physical defense barrier to eliminate re-infection in root canal and to disturb nutrition supply for bacterial development. Purpose: The aim of this study is observe the effectiveness of Ca(OH2 in treating endodontic teeth with apical periodontitis. Cases: Case 1 and 3 are about patients whose left posterior mandibular teeth had spontaneous intermittent pain. Case 2 is about a patient whose left posterior maxillary teeth had gingival abscess and fracture history. Based on the radiographic examination, it was known that the filling of root canal was incomplete and there was radiolucency in the apical area. Case management: The cases were treated with triad endodontics, which involves preparation, disinfection by using 2.5% NaOCl as irrigation substance and calcium hydroxide as intracanal dressing, and then the filling of root canal with gutta percha and endomethasone root canal cement. Evaluations were conducted one month, 12 months, and 24 months after the treatment. Conclusion: Calcium hydroxide is effective to be used as intracanal dressing in apical periodontitis cases.Latar belakang: Infeksi saluran akar dan penyakit periapeks disebabkan oleh mikroba dan produknya. Infeksi yang berlangsung lama memungkinkan bakteri masuk ke dalam seluruh sistem saluran akar. Periodontitis apikal disebabkan oleh infeksi persisten mikroba di dalam sistem saluran akar disertai perubahan radiografik dan

Nanoparticles for cultural heritage conservation: calcium and barium hydroxide nanoparticles for wall painting consolidation.

Science.gov (United States)

Giorgi, Rodorico; Ambrosi, Moira; Toccafondi, Nicola; Baglioni, Piero

2010-08-16

Nanotechnology provides new concepts and materials for the consolidation and protection of wall paintings. In particular, humble calcium and barium hydroxide nanoparticles offer a versatile and highly efficient tool to combat the main degradation processes altering wall paintings. Clear example of the efficacy and potentiality of nanotechnology is represented by the conservation in situ of Maya wall paintings in the archaeological area in Calakmul (Mexico).

Effect of a calcium hydroxide-based root canal dressing on periapical repair in dogs: a histological study.

Science.gov (United States)

Leonardo, Mario R; Hernandez, Maria E F T; Silva, Léa A B; Tanomaru-Filho, Mário

2006-11-01

To compare the periapical repair of teeth with periapical lesion following root canal treatment by using a calcium hydroxide-based intracanal dressing for several time periods or filling in a single visit. After induction of periapical lesions in 4 dogs, the root canals were prepared using 5.25% sodium hypochlorite for irrigation, and animals were separated into 4 experimental groups; in group I, root canals were filled in a single session; in groups II, III, and IV, a calcium hydroxide-based dressing was kept in place for 15, 30, or 180 days, respectively. Root canals from groups I, II, and III were filled with gutta-percha cones and AH Plus sealer. After 180 days, animals were killed and histological sections were stained with hematoxylin-eosin to evaluate periapical repair. Periapical repair was better in groups II, III, and IV (intracanal dressing) compared with group I (single session; P session treatment.

Automated solid-phase extraction of phenolic acids using layered double hydroxide-alumina-polymer disks.

Science.gov (United States)

Ghani, Milad; Palomino Cabello, Carlos; Saraji, Mohammad; Manuel Estela, Jose; Cerdà, Víctor; Turnes Palomino, Gemma; Maya, Fernando

2018-01-26

The application of layered double hydroxide-Al 2 O 3 -polymer mixed-matrix disks for solid-phase extraction is reported for the first time. Al 2 O 3 is embedded in a polymer matrix followed by an in situ metal-exchange process to obtain a layered double hydroxide-Al 2 O 3 -polymer mixed-matrix disk with excellent flow-through properties. The extraction performance of the prepared disks is evaluated as a proof of concept for the automated extraction using sequential injection analysis of organic acids (p-hydroxybenzoic acid, 3,4-dihydroxybenzoic acid, gallic acid) following an anion-exchange mechanism. After the solid-phase extraction, phenolic acids were quantified by reversed-phase high-performance liquid chromatography with diode-array detection using a core-shell silica-C18 stationary phase and isocratic elution (acetonitrile/0.5% acetic acid in pure water, 5:95, v/v). High sensitivity and reproducibility were obtained with limits of detection in the range of 0.12-0.25 μg/L (sample volume, 4 mL), and relative standard deviations between 2.9 and 3.4% (10 μg/L, n = 6). Enrichment factors of 34-39 were obtained. Layered double hydroxide-Al 2 O 3 -polymer mixed-matrix disks had an average lifetime of 50 extractions. Analyte recoveries ranged from 93 to 96% for grape juice and nonalcoholic beer samples. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Effect of ultrasonic streaming on intra-dentinal disinfection and penetration of calcium hydroxide paste in endodontic treatment

Directory of Open Access Journals (Sweden)

Marcela Paola Castro ARIAS

Full Text Available ABSTRACT Objective The antimicrobial effect of ultrasonic agitation of calcium hydroxide (CH pastes in infected bovine dentin and their penetrability were evaluated using confocal laser scanning microscopy (CLSM and microbiological culture. Material and Methods Fifty-two bovine teeth were infected with Enterococcus faecalis using a new contamination protocol; then they received CH paste and were divided into groups with or without ultrasound. Ultrasonic agitation was conducted for 1 min with a plain point insert. After 15 d, the CLSM analyzed the viable and dead bacteria with Live and Dead assay. The dentinal wall debris was collected by burs, and the colony forming units (CFU/mL were counted. The penetrability of the paste inside dentinal tubules was tested using the B-rodamine dye. Results The calcium hydroxide paste showed better results with the use of ultrasonic agitation (p<0.05. Conclusion The ultrasonic agitation of CH paste increased its antimicrobial action and was responsible for intradentinal penetration with the fulfilment of the tubules.

Effect of calcium hydroxide application to feedlot pen surface material on ammonia, odor, and greenhouse gas emissions

Science.gov (United States)

Calcium hydroxide (lime) is used to reduce microorganisms and odors in human biosolids, animal and poultry manures, and abattoir wastes. In the cattle industry, lime has been used as a disinfectant and is spread on the pen surface to control infections such as diarrhea and foot rot. The increase in ...

Oily calcium hydroxide suspension (Osteoinductal) used as an adjunct to guided bone regeneration: an experimental study in rats.

NARCIS (Netherlands)

Stavropoulos, A.; Geenen, C.; Nyengaard, J.R.; Karring, T.; Sculean, A.

2007-01-01

OBJECTIVES: To evaluate whether an oily calcium hydroxide suspension (OCHS) promotes bone healing when used as an adjunct to guided bone regeneration (GBR). MATERIAL AND METHODS: Rigid, hemispherical, teflon capsules were placed with their open part facing the lateral surface of the ramus on both

The reductive decomposition of calcium sulphate I. Kinetics of the apparent solid-solid reaction

NARCIS (Netherlands)

Kamphuis, B.; Potma, A.W.; Prins, W.; van Swaaij, Willibrordus Petrus Maria

1992-01-01

The reductive decomposition of calcium sulphate by hydrogen is used for the regeneration of calcium-based atmospheric fluidized bed combustion (AFBC) SO2 sorbents. The apparent solid¿solid reaction between CaS and CaSO4, one of the steps involved in the reaction mechanism of the reductive

Duration for Apical Barrier Formation in Necrotic Immature Permanent Incisors Treated With Calcium Hydroxide Apexification Using Ultrasonic or Hand Filing

Directory of Open Access Journals (Sweden)

Li-Wan Lee

2010-08-01

Conclusion: Ultrasonic filing with 0.2% chlorhexidine as an irrigant is effective for disinfection of the root canal and can shorten the duration for apical barrier formation in necrotic permanent incisors treated with calcium hydroxide apexification.

Antioxidant and cytoprotective activities of Piper betle, Areca catechu, Uncaria gambir and betel quid with and without calcium hydroxide.

Science.gov (United States)

Sazwi, Nordin Nur; Nalina, Thurairajah; Abdul Rahim, Zubaidah Haji

2013-12-11

Betel quid chewing is a popular habit in Southeast Asia. It is believed that chewing betel quid could reduce stress, strengthen teeth and maintain oral hygiene. The aim of this study was to investigate the antioxidant and cytoprotective activities of each of the ingredients of betel quid and compared with betel quid itself (with and without calcium hydroxide). The correlation of their cytoprotective and antioxidant activities with phenolic content was also determined. Five samples (betel leaf, areca nut, gambir, betel quid and betel quid containing calcium hydroxide) were extracted in deionized distilled water for 12 hours at 37°C. Antioxidant activities were evaluated for radical scavenging activity using DPPH assay, ferric reducing activity using FRAP assay and lipid peroxidation inhibition activity using FTC assay. Total phenolic content (TPC) was determined using Folin-Ciocalteu procedure. Phenolic composition was analyzed using LC-MS/MS. Cytoprotective activity towards human gingival fibroblast cells was examined using MTT assay. Among the ingredients of betel quid, gambir demonstrated the highest antioxidant (DPPH - IC50 = 6.4 ± 0.8 μg/mL, FRAP - 5717.8 ± 537.6 μmol Fe(II)/mg), total phenolic content (TPC - 1142.5 ± 106.8 μg TAE/mg) and cytoprotective (100.1 ± 4.6%) activities. Betel quid when compared with betel quid containing calcium hydroxide has higher antioxidant (DPPH - IC50 =59.4 ± 4.4 μg/mL, FRAP - 1022.2 ± 235.7 μmol Fe(II)/mg), total phenolic content (TPC - 140.0 ± 22.3 μg TAE/mg), and cytoprotective (113.5 ± 15.9%) activities. However, all of the five samples showed good lipid peroxidation inhibition compared to vitamin E. LC-MS/MS analysis revealed the presence of quinic acid as the major compound of gambir and betel quid. A positive correlation was observed between TPC and radical scavenging (r = 0.972), reducing power (r = 0.981) and cytoprotective activity (r = 0.682). The betel quid has higher TPC, and antioxidant and

Microstructure of amorphous aluminum hydroxide in belite-calcium sulfoaluminate cement

Energy Technology Data Exchange (ETDEWEB)

Song, Fei; Yu, Zhenglei; Yang, Fengling; Lu, Yinong, E-mail: yinonglu@njtech.edu.cn; Liu, Yunfei, E-mail: yfliu@njtech.edu.cn

2015-05-15

Belite-calcium sulfoaluminate (BCSA) cement is a promising low-CO{sub 2} alternative to ordinary Portland cement. Herein, aluminum hydroxide (AH{sub 3}), the main amorphous hydration product of BCSA cement, was investigated in detail. The microstructure of AH{sub 3} with various quantities of gypsum was investigated via scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). The AH{sub 3} with various morphologies were observed and confirmed in the resulting pastes. Particular attention was paid to the fact that AH{sub 3} always contained a small amount of Ca according to the results of EDS analysis. The AH{sub 3} was then characterized via high resolution transmission electron microscopy (HRTEM). The results of HRTEM indicated that Ca arose from nanosized tricalcium aluminate hexahydrate which existed in the AH{sub 3}.

Effects of instrumentation, irrigation and dressing with calcium hydroxide on infection in pulpless teeth with periapical bone lesions

NARCIS (Netherlands)

Peters, LB; van Winkelhoff, AJ; Buijs, JF; Wesselink, PR

Aim The aim of this study was to evaluate the fate of microorganisms in root canals of teeth with infected pulps and periapical bone lesions with and without the use of calcium hydroxide medication. Methodology Endodontic samples were cultured and microorganisms were counted and identified in 4 3

Dual nutraceutical nanohybrids of folic acid and calcium containing layered double hydroxides

Energy Technology Data Exchange (ETDEWEB)

Kim, Tae-Hyun; Oh, Jae-Min, E-mail: jaemin.oh@yonsei.ac.kr

2016-01-15

Dual nutraceutical nanohybrids consisting of organic nutrient, folic acid (FA), and mineral nutrient, calcium, were prepared based on layered double hydroxide (LDH) structure. Among various hybridization methods such as coprecipitation, ion exchange, solid phase reaction and exfoliation-reassembly, it was found that exfoliation-reassembly was the most effective in terms of intercalation of FA moiety between Ca-containing LDH layers. X-ray diffraction patterns and infrared spectra indicated that FA molecules were well stabilized in the interlayer space of LDHs through electrostatic interaction. From the atomic force and scanning electron microscopic studies, particle thickness of LDH was determined to be varied with tens, a few and again tens of nanometers in pristine, exfoliated and reassembled state, respectively, while preserving particle diameter. The result confirmed layer-by-layer hybrid structure of FA and LDHs was obtained by exfoliation-reassembly. Solid UV–vis spectra showed 2-dimensional molecular arrangement of FA moiety in hybrid, exhibiting slight red shift in n→π* and π→π* transition. The chemical formulae of FA intercalated Ca-containing LDH were determined to Ca{sub 1.30}Al(OH){sub 4.6}FA{sub 0.74}·3.33H{sub 2}O and Ca{sub 1.53}Fe(OH){sub 5.06}FA{sub 2.24}·9.94H{sub 2}O by inductively coupled plasma-atomic emission spectroscopy, high performance liquid chromatography and thermogravimetry, showing high nutraceutical content of FA and Ca. - Highlights: • We successfully intercalated FA molecules into Ca-containing LDHs. • Exfoliation-reassembly was proven to be the most effective. • The interaction between LDH and FA were studied by FT-IR and UV–vis spectra. • Thermal stability of FA were enhanced by electrostatic interaction with LDH layers.

Interaction of natural borates with potassium hydroxide solution

International Nuclear Information System (INIS)

Azarova, L.A.; Vinogradov, E.E.; Kudinov, I.B.; Panasyuk, G.P.; Danilov, V.P.

2000-01-01

Interaction of natural borates - inyoite, ulexite and hydroboracite MgCa[B 3 O 4 (OH) 3 ] 2 ·3H 2 O with KOH solution is studied at 50 Deg C by the methods of chemical, x- ray phase, differential thermal analyses and IR spectroscopy. IR spectra points out on island character of forming borates and confirms the data of x-ray phase and chemical analyses about presence of asharite and calcium hydrous borate in resulting products. Hydroboracite (chain structure) under the action of potassium hydroxide passes into borates of magnesium and calcium with island structure and in this case boron transforms partially into liquid phase. When potassium hydroxide interacts with inyoite and ulexite calcium hydroxide and roentgenoamorphous boron-containing product precipitate [ru

Thermal reactions of some calcium, strontium, and barium chromates

International Nuclear Information System (INIS)

Piekarska-Piesse, B.; Gontarz, Z.; Ostrowski, A.; Kucharski, R.

2000-01-01

Thermal decomposition of calcium chromates and solid state reactions of barium and strontium chromates(VI) with barium and strontium hydroxides and carbonates, as well as the reduction of chromates by carbon and hydrogen, have been investigated. The mechanisms of individual stages of the thermal decomposition have been proposed on the basis of morphological classification. (author)

In vitro antimicrobial and anti-endotoxin action of Zingiber Officinale as auxiliary chemical and medicament combined to calcium hydroxide and chlorhexidine.

Science.gov (United States)

Valera, Marcia Carneiro; Cardoso, Flávia Goulart da Rosa; Maekawa, Lilian Eiko; Camargo, Carlos Henrique Ribeiro; de Oliveira, Luciane Dias; Carvalho, Cláudio Antônio Talge

2015-01-01

This study was conducted in vitro to compare the effectiveness of Zingiber Officinale as an auxiliary chemical substance followed by placement of different intra-canal medication in removing endotoxins and cultivable micro-organisms from infected root canals. Seventy-two root canals were contaminated with Enterococcus faecalis, Candida albicans and Escherichia coli for 28 days. After, the teeth were instrumented using Zingiber Officinale and divided into six groups according to the intra-canal medication: chlorhexidine gel; calcium hydroxide + chlorhexidine gel; glycolic ginger extract; calcium hydroxide + glycolic ginger extract; calcium hydroxide + saline solution and saline solution (control). Sample collections were performed after root canal contamination (Baseline; S1), after instrumentation (S2), 7 days after instrumentation (S3), after 14 days with intra-canal medication (S4) and 7 days after removal of intra-canal medication (S5). The results were analyzed by the Kruskal-Wallis and Dunn tests. It was observed that in S2 and S3 there was significant reduction of the micro-organisms and the quantity of endotoxins after instrumentation. In samples S4 and S5 there was complete elimination of micro-organisms and significant reduction of endotoxins. It was concluded that Zingiber Officinale as an auxiliary chemical substance was effective on the micro-organisms tested, yet was unable to eliminate the endotoxins. Similarly, the intra-canal medication were effective on micro-organisms, yet did not completely eliminate the endotoxins.

Structural and nano-mechanical properties of Calcium Silicate Hydrate (C-S-H) formed from alite hydration in the presence of sodium and potassium hydroxide

International Nuclear Information System (INIS)

Mendoza, Oscar; Giraldo, Carolina; Camargo, Sergio S.; Tobón, Jorge I.

2015-01-01

This research evaluates the effect of sodium and potassium hydroxide on the structure and nano-mechanical properties of Calcium Silicate Hydrate (C-S-H) formed from the hydration of pure alite. Monoclinic (MIII) alite was synthesized and hydrated, using water-to-alite ratios of 0.5 and 0.6 and additions of 10% NaOH and KOH by weight of alite. Based on results of X-ray diffraction, isothermal calorimetry, thermogravimetric analysis, Nuclear Magnetic Resonance and nanoindentation, two different effects of the alkaline hydroxides on the hydration reaction of alite, both at early and later ages, can be identified: (i) a differentiated hydration process, attributed to an enhancement in calcium hydroxide (CH) precipitation and a stimulation of the C-S-H nuclei; and (ii) an increase in the elastic modulus of the C-S-H aggregations, attributed to an electrostatic attraction between positive charges from the alkaline cations and negative charges from the C-S-H structure

Structural and nano-mechanical properties of Calcium Silicate Hydrate (C-S-H) formed from alite hydration in the presence of sodium and potassium hydroxide

Energy Technology Data Exchange (ETDEWEB)

Mendoza, Oscar, E-mail: oamendoz@unal.edu.co [Grupo del Cemento y Materiales de Construcción (CEMATCO). Universidad Nacional de Colombia, Facultad de Minas, Medellín (Colombia); Giraldo, Carolina [Cementos Argos S.A., Medellín (Colombia); Camargo, Sergio S. [Engenharia Metalúrgica e de Materiais, Universidade Federal do Rio de Janeiro/COPPE, Rio de Janeiro (Brazil); Tobón, Jorge I. [Grupo del Cemento y Materiales de Construcción (CEMATCO). Universidad Nacional de Colombia, Facultad de Minas, Medellín (Colombia)

2015-08-15

This research evaluates the effect of sodium and potassium hydroxide on the structure and nano-mechanical properties of Calcium Silicate Hydrate (C-S-H) formed from the hydration of pure alite. Monoclinic (MIII) alite was synthesized and hydrated, using water-to-alite ratios of 0.5 and 0.6 and additions of 10% NaOH and KOH by weight of alite. Based on results of X-ray diffraction, isothermal calorimetry, thermogravimetric analysis, Nuclear Magnetic Resonance and nanoindentation, two different effects of the alkaline hydroxides on the hydration reaction of alite, both at early and later ages, can be identified: (i) a differentiated hydration process, attributed to an enhancement in calcium hydroxide (CH) precipitation and a stimulation of the C-S-H nuclei; and (ii) an increase in the elastic modulus of the C-S-H aggregations, attributed to an electrostatic attraction between positive charges from the alkaline cations and negative charges from the C-S-H structure.

Effects of irrigation solutions and Calcium hydroxide dressing on root canal treatments of periapical lesions

OpenAIRE

Nirmala, Vita

2006-01-01

The preparation of root canal in endodontic treatment plays an important role in treating non vital teeth with periapical lesion. Some factors influence the success of root canal treatment in short and long terms are the irrigation of root canal using antiseptic solution and the use of root canal medicament. The aim of this literature study is to determined the effect of irrigation solution and Calcium hydroxide dressing in root canal treatment of periapical lesions. The use of root canal med...

Chemically and compositionally modified solid solution disordered multiphase nickel hydroxide positive electrode for alkaline rechargeable electrochemical cells

Science.gov (United States)

Ovshinsky, Stanford R.; Corrigan, Dennis; Venkatesan, Srini; Young, Rosa; Fierro, Christian; Fetcenko, Michael A.

1994-01-01

A high capacity, long cycle life positive electrode for use in an alkaline rechargeable electrochemical cell comprising: a solid solution nickel hydroxide material having a multiphase structure that comprises at least one polycrystalline .gamma.-phase including a polycrystalline .gamma.-phase unit cell comprising spacedly disposed plates with at least one chemical modifier incorporated around the plates, the plates having a range of stable intersheet distances corresponding to a 2.sup.+ oxidation state and a 3.5.sup.+, or greater, oxidation state; and at least one compositional modifier incorporated into the solid solution nickel hydroxide material to promote the multiphase structure.

An in vitro investigation of a newer intracanal medicament Nisin on Enterococcus faecalis in comparison with chlorhexidine and calcium hydroxide

Directory of Open Access Journals (Sweden)

Suneel Kumar Chinni

2011-01-01

Full Text Available Aim: To determine the antibacterial efficacy of Nisin in comparison with Calcium hydroxide and Chlorhexidine. Materials and Methods: Fifty extracted lower premolar single-rooted teeth were collected and were instrumented with K3 rotary files. Then, root canals were inoculated with a bacterial solution of Enterococcus faecalis. After 21 days, the canals were inoculated with Saline, Nisin, Vancomycin, Calcium hydroxide, and Chlorhexidine. The roots were left for 7 days and on the 8 th day, to investigate the degree of infection of the radicular dentin, specimens of the dentin chips from the full length of the root canal were harvested using a sterile rotary K3 instrument (size 25 6% taper. Results: The results of the present study showed that Nisin and Chlorhexidine showed none of Colony Forming Units (CFU in their respective group. Conclusion: Within the limits of the study, Nisin was effective in eradicating E. faecalis cells in pure culture and root canal dentin.

Aerobic Oxidation of 5-(Hydroxymethyl)furfural in Ionic Liquids with Solid Ruthenium Hydroxide Catalysts

DEFF Research Database (Denmark)

Ståhlberg, Tim Johannes Bjarki; Eyjolfsdottir, Ester; Gorbanev, Yury

2012-01-01

The aerobic oxidation of 5-(hydroxymethyl)furfural was investigated over solid ruthenium hydroxide catalysts in ionic liquids at elevated temperatures and pressures. Several different catalyst supports were tested in combination with various ionic liquids. The best result was obtained in [EMIm...

Investigation into process of solid-phase synthesis of calcium vanadates

International Nuclear Information System (INIS)

Fotiev, A.A.; Krasnenko, T.I.; Slobodin, B.V.

1983-01-01

Processes of solid-phase synthesis of calcium vanadates by Toubandt method, measuring electric conductivity and Ca 45 and V 48 radioactive indicators are investigated. It is shown that reaction diffusion during calcium vanadates production from oxides is ensured by calcium and oxygen ions or calcium ions and electrons through the product layer, as to oxygen - through the gas phase

Calcium hydroxide nanoparticles for the conservation of cultural heritage: new formulations for the deacidification of cellulose-based artifacts

Science.gov (United States)

Poggi, G.; Toccafondi, N.; Melita, L. N.; Knowles, J. C.; Bozec, L.; Giorgi, R.; Baglioni, P.

2014-03-01

Alkaline earth metal hydroxide nanoparticles dispersions have demonstrated to be efficient for the preservation of cellulose-based artifacts, providing a stable neutral environment and, if in excess, turning into mild alkaline species. New formulations tailored for specific conservation issues have been recently obtained via a solvothermal reaction, starting from bulk metal, and short chain alcohols. Using this synthetic procedure, stable, and high concentrated calcium hydroxide nanoparticles dispersions can be obtained. The characterization of nanoparticles was carried out by dynamic light scattering, transmission electron microscopy and X-ray powder diffraction and showed that the dispersed systems are particularly suitable for the application on porous substrates. In a direct application of this technology, acidic paper and canvas samples were artificially aged after deacidification using calcium hydroxide nanoparticles dispersed in short chain alcohols. Cellulose viscosimetric polymerization degree (DPv), cellulose pyrolysis temperature, and samples' pH were evaluated upon the aging and in terms of protective action arising from the applied treatment. In particular, determinations of DPv clearly showed that the degradation of acidic paper and canvas samples proceeds at higher rates with respect to deacidified samples. These evidences were also confirmed by the thermogravimetric analysis of samples, in which the benefits due to the deacidification treatments are measured in terms of pyrolysis temperature of cellulose. These new formulations of nanoparticles dispersions expand the palette of available tools for the conservation of cellulose-based works of art, such as easel paintings, and manuscripts, potentially opening the way for the intervention on parchment and leather, whose preservation is a particularly challenging task.

Precursor preparation for Ca-Al layered double hydroxide to remove hexavalent chromium coexisting with calcium and magnesium chlorides

Energy Technology Data Exchange (ETDEWEB)

Zhong, Lihua; He, Xiaoman; Qu, Jun; Li, Xuewei; Lei, Zhiwu; Zhang, Qiwu [School of Resources and Environment Engineering, Wuhan University of Technology, Wuhan 430070 (China); Liu, Xinzhong [College of Ecological Environment and Urban Construction, Fujian University of Technology, Fuzhou 350118 (China)

2017-01-15

Al(OH){sub 3} and Ca(OH){sub 2} powders are co-ground to prepare a precursor which hydrates into a layered double hydroxide (LDH) phase by agitation in aqueous solution with target hexavalent chromium (Cr(VI)) at room temperature, to achieve an obvious improvement in removal efficiency of Cr(VI) through an easy incorporation into the structure. Although the prepared precursor transforms into LDH phases also when agitated in the solutions of calcium and magnesium chlorides, it incorporates Cr(VI) preferentially to the chloride salts when they coexist. The adsorption isotherm and kinetic studies show that the phenomena occurring on the Al-Ca precursor fit a pseudo-second-order kinetics with a Langmuir adsorption capacity of 59.45 mg/g. Besides, characterizations of the prepared precursor and the samples after adsorption are also performed by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), Transmission electron microscope (TEM) to understand the reason of the preferential incorporation of Cr(VI) to the coexisting chloride salts during the LDH phase formation. - Graphical abstract: Activated Ca-Al hydroxides (C{sub 3}A) transformed into Ca-Al-OH compound when agitated in water. Ca-Al precursor (C{sub 3}A) was agitated in a hexavalent chromium (Cr(VI)) solution to form Al-Ca-CrO{sub 4} LDH product. Ca-Al-CrO{sub 4} LDH phase occurred preferentially to Ca-Al-MCl{sub 2} LDH phases in the solutions of calcium and magnesium chlorides, it incorporates Cr(VI) preferentially to the chloride salts when they coexist. - Highlights: • Activated Ca-Al hydroxides transformed into LDH when agitated in water with some inorganic substances. • Hexavalent Cr was incorporated in the LDH structure at high adsorption capacity. • Ca-Al-Cr LDH phase occurred preferentially to Ca-Al-MCl{sub 2} LDH phases with coexistence. • The prepared Ca-Al hydroxides had high performance as adsorbent even with high salinity of the solution.

Precursor preparation for Ca-Al layered double hydroxide to remove hexavalent chromium coexisting with calcium and magnesium chlorides

International Nuclear Information System (INIS)

Zhong, Lihua; He, Xiaoman; Qu, Jun; Li, Xuewei; Lei, Zhiwu; Zhang, Qiwu; Liu, Xinzhong

2017-01-01

Al(OH) 3 and Ca(OH) 2 powders are co-ground to prepare a precursor which hydrates into a layered double hydroxide (LDH) phase by agitation in aqueous solution with target hexavalent chromium (Cr(VI)) at room temperature, to achieve an obvious improvement in removal efficiency of Cr(VI) through an easy incorporation into the structure. Although the prepared precursor transforms into LDH phases also when agitated in the solutions of calcium and magnesium chlorides, it incorporates Cr(VI) preferentially to the chloride salts when they coexist. The adsorption isotherm and kinetic studies show that the phenomena occurring on the Al-Ca precursor fit a pseudo-second-order kinetics with a Langmuir adsorption capacity of 59.45 mg/g. Besides, characterizations of the prepared precursor and the samples after adsorption are also performed by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), Transmission electron microscope (TEM) to understand the reason of the preferential incorporation of Cr(VI) to the coexisting chloride salts during the LDH phase formation. - Graphical abstract: Activated Ca-Al hydroxides (C 3 A) transformed into Ca-Al-OH compound when agitated in water. Ca-Al precursor (C 3 A) was agitated in a hexavalent chromium (Cr(VI)) solution to form Al-Ca-CrO 4 LDH product. Ca-Al-CrO 4 LDH phase occurred preferentially to Ca-Al-MCl 2 LDH phases in the solutions of calcium and magnesium chlorides, it incorporates Cr(VI) preferentially to the chloride salts when they coexist. - Highlights: • Activated Ca-Al hydroxides transformed into LDH when agitated in water with some inorganic substances. • Hexavalent Cr was incorporated in the LDH structure at high adsorption capacity. • Ca-Al-Cr LDH phase occurred preferentially to Ca-Al-MCl 2 LDH phases with coexistence. • The prepared Ca-Al hydroxides had high performance as adsorbent even with high salinity of the solution.

Calcium chromate process related investigations

International Nuclear Information System (INIS)

Dillard, B.M.

1979-01-01

A pilot plant for production of calcium chromate has been scaled up to a small production facility at the General Electric Neutron Devices Department. In preparation for this scale-up, the process and final product were studied in order to evaluate problems not considered previously. The variables and processes studied included: (1) the determination of optimum drying temperature and time for product analysis; (2) the effect of the grade of lime used as the precipitating agent on the purity of the calcium chromate; (3) product purity when calcium chromate is precipitated by the addition of ammonium chromate to slaked lime; (4) the reagents best suited for cleaning calcium chromate spills; and (5) methods for determining hydroxide ion concentration in calcium chromate. The optimum drying time for the product before analysis is four hours at 600 0 C. Gases evolved at various temperatures during the drying process were carbon dioxide and water vapor. Technical grade lime produced calcium chromate of the highest purity. Both nitric and acetic acids were efficient dissolvers of calcium chromate spills. Direct titration of hydroxide ion with sulfuric acid gave an average recovery of 93% for samples spiked with calcium hydroxide. 1 figure, 17 tables

Production of calcium hydroxide from the waste of Cariri stone; Producao de hidroxido de calcio a partir de residuo da pedra Cariri

Energy Technology Data Exchange (ETDEWEB)

Alves, T.M.E.; Santos, A.M.M.; Brasileiro, M.I.; Pinheiro, S.F.L.; Prado, A.C.A., E-mail: tiagomaiaea@gmail.com [Universidade Federal do Cariri (UFCA), Juazeiro do Norte, CE (Brazil)

2016-07-01

The extraction of Cariri stone in the northeast is a frequent activity because of its ornamental application as well as for the construction sector. However, by this extraction, untapped waste formation grows and becomes a problem for the environment. The objective of this work is to produce calcium hydroxide, from this limestone residue, with controlled porosity, solubility and particle size. The waste was characterized with X-Ray Diffraction (XRD), X-Ray Fluorescence (XRF) and thermal analysis (TGA). The limestone was calcined at 850°C and 950°C for 45 minutes and three hours, being characterized by XRD, XRF and TGA. Once calcined, it was hydrated with 17,5g and 22g oxide to 100mL water and manually mixed for 15 and 25 minutes. The calcium hydroxides have been submitted for tests in vivo in rats and will be characterized by XRD, Scanning Electron Microscopy (SEM) and Infrared. (author)

Effect of calcium hydroxide on mechanical strength and biological properties of bioactive glass.

Science.gov (United States)

Shah, Asma Tufail; Batool, Madeeha; Chaudhry, Aqif Anwar; Iqbal, Farasat; Javaid, Ayesha; Zahid, Saba; Ilyas, Kanwal; Bin Qasim, Saad; Khan, Ather Farooq; Khan, Abdul Samad; Ur Rehman, Ihtesham

2016-08-01

In this manuscript for the first time calcium hydroxide (Ca(OH)2) has been used for preparation of bioactive glass (BG-2) by co-precipitation method and compared with glass prepared using calcium nitrate tetrahydrate Ca(NO3)2·4H2O (BG-1), which is a conventional source of calcium. The new source positively affected physical, biological and mechanical properties of BG-2. The glasses were characterized by Fourier transform infrared (FTIR), X-Ray Diffractometer (XRD), Scanning Electron Microscopy (SEM), Thermogravimetric Analysis/Differential Scanning Calorimetry (TGA-DSC), BET surface area analysis and Knoop hardness. The results showed that BG-2 possessed relatively larger surface properties (100m(2)g(-1) surface area) as compared to BG-1 (78m(2)g(-1)), spherical morphology and crystalline phases (wollastonite and apatite) after sintering at lower than conventional temperature. These properties contribute critical role in both mechanical and biological properties of glasses. The Knoop hardness measurements revealed that BG-2 possessed much better hardness (0.43±0.06GPa at 680°C and 2.16±0.46GPa at 980°C) than BG-1 (0.24±0.01 at 680°C and 0.57±0.07GPA at 980°C) under same conditions. Alamar blue Assay and confocal microscopy revealed that BG-2 exhibited better attachment and proliferation of MG63 cells. Based on the improved biological properties of BG-2 as a consequent of novel calcium source selection, BG-2 is proposed as a bioactive ceramic for hard tissue repair and regeneration applications. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effect of calcium hydroxide and triple antibiotic paste as intracanal medicaments on the incidence of inter-appointment flare-up in diabetic patients: An in vivo study

Science.gov (United States)

Pai, Swathi; Vivekananda Pai, A. R.; Thomas, Manuel S.; Bhat, Vishal

2014-01-01

Aim: To evaluate and compare the effect of antibacterial intracanal medicaments on inter-appointment flare-up in diabetic patients. Materials and Methods: Fifty diabetic patients requiring root canal treatment were assigned into groups I, II, and III. In group I, no intracanal medicament was placed. In groups II and III, calcium hydroxide and triple antibiotic pastes were placed as intracanal medicaments, respectively. Patients were instructed to record their pain on days 1, 2, 3, 7, and 14. Inter-appointment flare-up was evaluated using verbal rating scale (VRS). Results: Overall incidence of inter-appointment flare-up among diabetic patients was found to be 16%. In group I, 50% of the patients and in group II, 15% of the patients developed inter-appointment flare-up. However, no patients in group III developed inter-appointment flare-up. The comparison of these results was found to be statistically significant (P = 0.002; χ2 = 12.426). However, with respect to intergroup comparison, only the difference between groups I and III was found to be statistically significant (P = 0.002; χ2 = 12.00). Conclusions: Calcium hydroxide and triple antibiotic paste are effective for managing inter-appointment flare-ups in diabetic patients. Triple antibiotic paste is more effective than calcium hydroxide in preventing the occurrence of flare-up in diabetic patients. PMID:24944440

A randomized clinical trial on the use of medical Portland cement, MTA and calcium hydroxide in indirect pulp treatment.

Science.gov (United States)

Petrou, Marina Agathi; Alhamoui, Fadi Alhaddad; Welk, Alexander; Altarabulsi, Mohammed Basel; Alkilzy, Mohammed; H Splieth, Christian

2014-01-01

Studies on indirect pulp treatment (IPT) show varying success rates of 73 to 97 %. The necessity of re-opening the cavity and the question of the optimal capping material is still under debate. The aim of this prospective in vivo study was to compare the clinical and microbiological outcomes of mineral trioxide aggregate (MTA), medical Portland cement, and calcium hydroxide on the dentin-pulp complex of permanent and primary teeth treated with two-step IPT. In 86 regular patients (51 % men; 49 % women; age 17.2 years ±13.8), one deep carious lesion each was treated with incomplete caries removal, randomly selected capping with either calcium hydroxide (n = 31), medical Portland cement (29) or white MTA (26), and re-entry (6.3 months ±1.0). Clinical (color, humidity, and consistency of dentin) and microbiological (Lactobacilli/Mutans Strep. counts) parameters were recorded at the first and second treatment. The IPT had a high success rate of 90.3 % regardless of the material used (p = 0.72). The arrested lesions showed consistently darker, dry, and therefore, sclerotic dentine (p Portland cement. The findings of this study could promote the improvement of the IPT as a one-step treatment of deep carious lesions when the remaining demineralized dentin would be sealed with durable restorations.

Solid-state NMR studies of form I of atorvastatin calcium.

Science.gov (United States)

Wang, Wei David; Gao, Xudong; Strohmeier, Mark; Wang, Wei; Bai, Shi; Dybowski, Cecil

2012-03-22

Solid-state (13)C, (19)F, and (15)N magic angle spinning NMR studies of Form I of atorvastatin calcium are reported, including chemical shift tensors of all resolvable carbon sites and fluorine sites. The complete (13)C and (19)F chemical shift assignments are given based on an extensive analysis of (13)C-(1)H HETCOR and (13)C-(19)F HETCOR results. The solid-state NMR data indicate that the asymmetric unit of this material contains two atorvastatin molecules. A possible structure of Form I of atorvastatin calcium (ATC-I), derived from solid-state NMR data and density functional theory calculations of various structures, is proposed for this important active pharmaceutical ingredient (API).

Influence of Calcium on Microbial Reduction of Solid Phase Uranium (VI)

International Nuclear Information System (INIS)

Liu, Chongxuan; Jeon, Byong-Hun; Zachara, John M.; Wang, Zheming

2007-01-01

The effect of calcium on microbial reduction of a solid phase U(VI), sodium boltwoodite (NaUO2SiO3OH · 1.5H2O), was evaluated in a culture of a dissimilatory metal-reducing bacterium (DMRB), Shewanella oneidensis strain MR-1. Batch experiments were performed in a non-growth bicarbonate medium with lactate as electron donor at pH 7 buffered with PIPES. Calcium increased both the rate and extent of Na-boltwoodite dissolution by increasing its solubility through the formation of a ternary aqueous calcium-uranyl-carbonate species. The ternary species, however, decreased the rates of microbial reduction of aqueous U(VI). Laser-induced fluorescence spectroscopy (LIFS) and transmission electron microscopy (TEM) revealed that microbial reduction of solid phase U(VI) is a sequentially coupled process of Na-boltwoodite dissolution, U(VI) aqueous speciation, and microbial reduction of dissolved U(VI) to U(IV) that accumulated on bacterial surfaces/periplasm. The overall rates of microbial reduction of solid phase U(VI) can be described by the coupled rates of dissolution and microbial reduction that were both influenced by calcium. The results demonstrated that dissolved U(VI) concentration during microbial reduction was a complex function of solid phase U(VI) dissolution kinetics, aqueous U(VI) speciation, and microbial activity

Selective Aerobic Oxidation of 5-Hydroxymethylfurfural in Water Over Solid Ruthenium Hydroxide Catalysts with Magnesium-Based Supports

DEFF Research Database (Denmark)

Gorbanev, Yury; Kegnæs, Søren; Riisager, Anders

2011-01-01

Solid catalyst systems comprised of ruthenium hydroxide supported on magnesium-based carrier materials (spinel, magnesium oxide and hydrotalcite) were investigated for the selective, aqueous aerobic oxidation of the biomass-derived chemical 5-hydroxymethylfurfural into 2,5-furandicarboxylic acid...

A preliminary report on histological outcome of pulpotomy with endodontic biomaterials vs calcium hydroxide.

Science.gov (United States)

Nosrat, Ali; Peimani, Ali; Asgary, Saeed

2013-11-01

The purpose of the study was to evaluate human dental pulp response to pulpotomy with calcium hydroxide (CH), mineral trioxide aggregate (MTA), and calcium enriched mixture (CEM) cement. A total of nine erupted third molars were randomly assigned to each pulpotomy group. The same clinician performed full pulpotomies and coronal restorations. The patients were followed clinically for six months; the teeth were then extracted and prepared for histological assessments. The samples were blindly assessed by an independent observer for pulp vitality, pulp inflammation, and calcified bridge formation. All patients were free of clinical signs/symptoms of pulpal/periradicular diseases during the follow up period. In CH group, one tooth had necrotic radicular pulp; other two teeth in this group had vital uninflamed pulps with complete dentinal bridge formation. In CEM cement and MTA groups all teeth had vital uninflamed radicular pulps. A complete dentinal bridge was formed beneath CEM cement and MTA in all roots. Odontoblast-like cells were present beneath CEM cement and MTA in all samples. This study revealed that CEM cement and MTA were reliable endodontic biomaterials in full pulpotomy treatment. In contrast, the human dental pulp response to CH might be unpredictable.

Comparative evaluation of the antimicrobial activity of natural extracts of Morinda citrifolia, papain and aloe vera (all in gel formulation), 2% chlorhexidine gel and calcium hydroxide, against Enterococcus faecalis: An in vitro study.

Science.gov (United States)

Bhardwaj, Anuj; Ballal, Suma; Velmurugan, Natanasabapathy

2012-07-01

A comparative evaluation of the antimicrobial activity of natural extracts of Morinda citrifolia, papain, and aloe vera (all in gel formulations), 2% chlorhexidine gel and calcium hydroxide, against Enterococcus faecalis-an in vitro study. The antimicrobial efficacy was assessed in vitro using dentin shavings collected at 2 depths of 200 and 400 μm. The total colony forming units at the end of 1, 3, and 5 days were assessed. The overall percentage inhibition of bacterial growth (200 and 400 μm depth) was 100% with chlorhexidine gel. This was followed by M. citrifolia gel (86.02%), which showed better antimicrobial efficacy as compared with aloe vera gel (78.9%), papain gel (67.3%), and calcium hydroxide (64.3%). There was no statistical difference between data at 200 and 400 μm depth. Chlorhexidine gel showed the maximum antimicrobial activity against E. faecalis, whereas calcium hydroxide showed the least. Among the natural intracanal medicaments, M. citrifolia gel consistently exhibited good inhibition up to the 5(th) day followed by aloe vera gel and papain gel.

Biopharmaceutical characterisation of ciprofloxacin-metallic ion interactions: comparative study into the effect of aluminium, calcium, zinc and iron on drug solubility and dissolution.

Science.gov (United States)

Stojković, Aleksandra; Tajber, Lidia; Paluch, Krzysztof J; Djurić, Zorica; Parojčić, Jelena; Corrigan, Owen I

2014-03-01

Ciprofloxacin bioavailability may be reduced when ciprofloxacin is co-administered with metallic ion containing preparations. In our previous study, physicochemical interaction between ciprofloxacin and ferrous sulphate was successfully simulated in vitro. In the present work, comparative in vitro ciprofloxacin solubility and dissolution studies were performed in the reactive media containing aluminium hydroxide, calcium carbonate or zinc sulphate. Solid phases collected from the dissolution vessel with aluminium hydroxide, calcium carbonate and zinc sulphate were investigated for their properties. The results obtained indicate that different types of adducts may form and retard ciprofloxacin solubility and dissolution. In the case of aluminium, no phase changes were observed. The solid phase generated in the presence of calcium carbonate was identified as hydrated ciprofloxacin base. Similarly to iron, a new complex consistent with Zn(SO4)2(Cl)2(ciprofloxacin)2 × nH2O stoichiometry was generated in the presence of relatively high concentrations of ciprofloxacin hydrochloride and zinc sulphate, indicating that small volume dissolution experiments can be useful for biorelevant dissolution tests.

Biopharmaceutical characterisation of ciprofloxacin-metallic ion interactions: Comparative study into the effect of aluminium, calcium, zinc and iron on drug solubility and dissolution

Directory of Open Access Journals (Sweden)

Stojković Aleksandra

2014-03-01

Full Text Available Ciprofloxacin bioavailability may be reduced when ciprofloxacin is co-administered with metallic ion containing preparations. In our previous study, physicochemical interaction between ciprofloxacin and ferrous sulphate was successfully simulated in vitro. In the present work, comparative in vitro ciprofloxacin solubility and dissolution studies were performed in the reactive media containing aluminium hydroxide, calcium carbonate or zinc sulphate. Solid phases collected from the dissolution vessel with aluminium hydroxide, calcium carbonate and zinc sulphate were investigated for their properties. The results obtained indicate that different types of adducts may form and retard ciprofloxacin solubility and dissolution. In the case of aluminium, no phase changes were observed. The solid phase generated in the presence of calcium carbonate was identified as hydrated ciprofloxacin base. Similarly to iron, a new complex consistent with Zn(SO42(Cl2(ciprofloxacin2 × nH2O stoichiometry was generated in the presence of relatively high concentrations of ciprofloxacin hydrochloride and zinc sulphate, indicating that small volume dissolution experiments can be useful for biorelevant dissolution tests.

Will mineral trioxide aggregate replace calcium hydroxide in treating pulpal and periodontal healing complications subsequent to dental trauma?

DEFF Research Database (Denmark)

Bakland, Leif K; Andreasen, Jens O

2012-01-01

Mineral trioxide aggregate (MTA) has over the last two decades begun to take the place of calcium hydroxide (CH) in the treatment of a variety of pulpal and periodontal healing complications following dental trauma. These conditions include teeth with: (i) exposed pulps, (ii) immature roots......, the quality of such induced hard tissues, and finally the dentin weakening effect of CH, which in some instances lead to cervical root fractures in immature teeth. MTA appears, from a relatively few clinical studies, to overcome these shortcomings of CH. The lack of long-term clinical studies, however, may...

Reaction Mechanism of Calcium Hydroxide with Gaseous Hydrogen Chloride Mécanisme de réaction de l'hydroxyde de calcium avec de l'acide chlorhydrique gazeux

Directory of Open Access Journals (Sweden)

Allal K. M.

2006-12-01

Full Text Available The reduction of acid gas content in combustion or incineration flue gases can be carried out by reaction with dry, fine alkaline sorbents such as calcium oxide or calcium hydroxide. In the present work, in addition to the thermodynamic study of the different reactions involved in the dechlorination process, an experimental study to identify the reaction products by means of X-ray diffraction, electron microscopy and thermogravimetry has been carried out. It has been shown that the reaction of hydrochloric acid with hydrated lime leads to the formation of not only calcium chloride but calcium hydroxichloride. La diminution de la teneur en gaz acides dans les effluents provenant des unités de combustion ou d'incinération peut être accomplie en faisant réagir ces gaz polluants avec des absorbants alcalins tels que l'oxyde ou l'hydroxyde de calcium. Dans cet article, à l'étude thermodynamique des différentes réactions mises en jeu durant le processus de déchloruration, s'ajoute une étude expérimentale menant à l'identification des produits finaux en utilisant la diffraction X, la microscopie électronique ainsi que la thermogravimétrie. A l'issue de cette étude, il a été montré que la réaction de Ca(OH2 avec HCl entraîne la formation non seulement de CaCI2 mais aussi CaCIOH.

Surface tension of calcium hydroxide associated with different substances Tensão superficial do hidróxido de cálcio associado a diferentes substâncias

Directory of Open Access Journals (Sweden)

Carlos Estrela

2005-06-01

Full Text Available The purpose of this study was to evaluate the surface tension of calcium hydroxide (CH associated with different substances (deionized distilled water, camphorated paramonochlorophenol, 2% chlorhexidine digluconate, Otosporin, 3% sodium lauryl ether sulphate; Furacin, PMC Furacin using tensiometer. The action of the substances studied on the dentinal structure enhances the property of surface tension. This method consists in the application of force to separate a platinum ring immersed in the substances. Thus, torsion was applied to the screw until the platinum ring separated during substances testing. Considering the methodology applied, the following can be concluded: distilled water alone or associated with CH presented a high surface tension (70.00 and 68.40 dynes/cm; calcium hydroxide in association with anionic detergent showed low surface tension (31.60 dynes/cm; camphorated paramonochlorophenol plus CH presented low surface tension (37.50 dynes/cm; 2% chlorhexidine associated with calcium hydroxide showed high surface tension values (58.00 dynes/cm; Otosporin plus calcium hydroxide showed low surface tension (35.40 dynes/cm; paramonochlorophenol Furacin mixed with calcium hydroxide presented surface tension equal to 45.50 dynes/cm; sodium hypochlorite presented high surface tension (75.00 dynes/cm. Antimicrobial agents more indicated in endodontics, i.e. CH, chlorhexidine and hypochlorite, presented the highest surface tension.Estudou-se a tensão superficial do hidróxido de cálcio associado a diferentes substâncias (água destilada deionizada, paramonoclorofenol canforado, digluconato de clorexidina 2%, Otosporin, sulfato éter lauril sódio 3%, furacin, PMC furacin usando tensiômetro. O modelo experimental consistiu na aplicação de uma força para separar um anel de platina imerso na superfície das substâncias, exercido por um tensiômetro. Considerando a metodologia aplicada, pode-se concluir: a água destilada isolada ou

21 CFR 573.240 - Calcium periodate.

Science.gov (United States)

2010-04-01

... with calcium hydroxide or calcium oxide to form a substance consisting of not less than 60 percent by... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Calcium periodate. 573.240 Section 573.240 Food... Additive Listing § 573.240 Calcium periodate. The food additive calcium periodate may be safely used in...

Evaluation of layered zinc hydroxide nitrate and zinc/nickel double hydroxide salts in the removal of chromate ions from solutions

International Nuclear Information System (INIS)

Bortolaz de Oliveira, Henrique; Wypych, Fernando

2016-01-01

Layered zinc hydroxide nitrate (ZnHN) and Zn/Ni layered double hydroxide salts were synthesized and used to remove chromate ions from solutions at pH 8.0. The materials were characterized by many instrumental techniques before and after chromate ion removal. ZnHN decomposed after contact with the chromate solution, whereas the layered structure of Zn/Ni hydroxide nitrate (Zn/NiHN) and Zn/Ni hydroxide acetate (Zn/NiHA) remained their layers intact after the topotactic anionic exchange reaction, only changing the basal distances. ZnHN, Zn/NiHN, and Zn/NiHA removed 210.1, 144.8, and 170.1 mg of CrO 4 2− /g of material, respectively. Although the removal values obtained for Zn/NiHN and Zn/NiHA were smaller than the values predicted for the ideal formulas of the solids (194.3 and 192.4 mg of CrO 4 2− /g of material, respectively), the measured capacities were higher than the values achieved with many materials reported in the literature. Kinetic experiments showed the removal reaction was fast. To facilitate the solid/liquid separation process after chromium removal, Zn/Ni layered double hydroxide salts with magnetic supports were also synthesized, and their ability to remove chromate was evaluated. - Highlights: • Zinc hydroxide nitrate and Zn/Ni hydroxide nitrate or acetate were synthesized. • The interlayer anions were replaced by chromate anions at pH=8.0. • Only Zn/Ni hydroxide nitrate or acetate have the structure preserved after exchange. • Fast exchange reaction and high capacity of chromate removal were observed. • Magnetic materials were obtained to facilitate the solids removal the from solutions.

Comparison of the adjuvant activity of aluminum hydroxide and calcium phosphate on the antibody response towards Bothrops asper snake venom.

Science.gov (United States)

Olmedo, Hidekel; Herrera, María; Rojas, Leonardo; Villalta, Mauren; Vargas, Mariángela; Leiguez, Elbio; Teixeira, Catarina; Estrada, Ricardo; Gutiérrez, José María; León, Guillermo; Montero, Mavis L

2014-01-01

The adjuvanticity of aluminum hydroxide and calcium phosphate on the antibody response in mice towards the venom of the snake Bothrops asper was studied. It was found that, in vitro, most of the venom proteins are similarly adsorbed by both mineral salts, with the exception of some basic phospholipases A2, which are better adsorbed by calcium phosphate. After injection, the adjuvants promoted a slow release of the venom, as judged by the lack of acute toxicity when lethal doses of venom were administered to mice. Leukocyte recruitment induced by the venom was enhanced when it was adsorbed on both mineral salts; however, venom adsorbed on calcium phosphate induced a higher antibody response towards all tested HPLC fractions of the venom. On the other hand, co-precipitation of venom with calcium phosphate was the best strategy for increasing: (1) the capacity of the salt to couple venom proteins in vitro; (2) the venom ability to induce leukocyte recruitment; (3) phagocytosis by macrophages; and (4) a host antibody response. These findings suggest that the chemical nature is not the only one determining factor of the adjuvant activity of mineral salts.

21 CFR 184.1207 - Calcium lactate.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Calcium lactate. 184.1207 Section 184.1207 Food and... Substances Affirmed as GRAS § 184.1207 Calcium lactate. (a) Calcium lactate (C6H10CaO6.xH2O, where x is any... calcium carbonate or calcium hydroxide. (b) The ingredient meets the specifications of the Food Chemicals...

Evaluation of layered zinc hydroxide nitrate and zinc/nickel double hydroxide salts in the removal of chromate ions from solutions

Energy Technology Data Exchange (ETDEWEB)

Bortolaz de Oliveira, Henrique; Wypych, Fernando, E-mail: wypych@ufpr.br

2016-11-15

Layered zinc hydroxide nitrate (ZnHN) and Zn/Ni layered double hydroxide salts were synthesized and used to remove chromate ions from solutions at pH 8.0. The materials were characterized by many instrumental techniques before and after chromate ion removal. ZnHN decomposed after contact with the chromate solution, whereas the layered structure of Zn/Ni hydroxide nitrate (Zn/NiHN) and Zn/Ni hydroxide acetate (Zn/NiHA) remained their layers intact after the topotactic anionic exchange reaction, only changing the basal distances. ZnHN, Zn/NiHN, and Zn/NiHA removed 210.1, 144.8, and 170.1 mg of CrO{sub 4}{sup 2−}/g of material, respectively. Although the removal values obtained for Zn/NiHN and Zn/NiHA were smaller than the values predicted for the ideal formulas of the solids (194.3 and 192.4 mg of CrO{sub 4}{sup 2−}/g of material, respectively), the measured capacities were higher than the values achieved with many materials reported in the literature. Kinetic experiments showed the removal reaction was fast. To facilitate the solid/liquid separation process after chromium removal, Zn/Ni layered double hydroxide salts with magnetic supports were also synthesized, and their ability to remove chromate was evaluated. - Highlights: • Zinc hydroxide nitrate and Zn/Ni hydroxide nitrate or acetate were synthesized. • The interlayer anions were replaced by chromate anions at pH=8.0. • Only Zn/Ni hydroxide nitrate or acetate have the structure preserved after exchange. • Fast exchange reaction and high capacity of chromate removal were observed. • Magnetic materials were obtained to facilitate the solids removal the from solutions.

Research of calcium oxide hydration in calcium nitrate solutions

Directory of Open Access Journals (Sweden)

M.A. Oliynyk

2016-09-01

Full Text Available Mineral fertilizers are one of the important factors of agriculture intensification and increasing of food products quantity. The volume of fertilizers production and its domestic consumption in Ukraine indicate that nitrogen fertilizer using only comes nearer to the required number of science-based. One of the most widespread artificial fertilizers is the calcium nitrate. Aim: The aim is to study and theoretically substantiate the processes occurring in the preparation of suspensions of calcium hydroxide Са(ОН2 in solution of calcium nitrate Ca(NО32. Materials and Methods: The technical calcium oxide (quicklime DSTU BV.2.7-90-99, solutions of calcium nitrate of 15, 20, 25, 30, 35 and 40% Ca(NО32 concentrations were used in the work. The content of lime in the preparation of a suspension in the solution changed (in terms of calcium oxide CaO from 150 g/dm3 to the maximum possible. Each of these solutions saturated at 40°С in lime to maximum concentration. Suitable for use in these experiments and in the technology of calcium nitrate obtaining are considered the solutions (suspensions that within 12 hours did not lose their mobility (transportability. Results: The experimental results show that increasing of the concentration of calcium nitrate in solution within the range 15...40%, the amount of lime that you can put into the solution without loss of transportability decreases. Further increasing of lime quantity in solutions concentrations causes to its solidifying, loss of mobility (transportability. Calculations showed that in the presence of calcium nitrate the solubility of Са(ОН2 is reduced nearly by order that can lead to the formation of calcium oxide CaO the solid phase Са(ОН2 on the surface, which also can form hydrogen bonds with the components of the solution. As the probability of formation of hydrogen bonds in solutions is high, there is a possibility of formation of clusters.

Dissolution mechanism of aluminum hydroxides in acid media

Science.gov (United States)

Lainer, Yu. A.; Gorichev, I. G.; Tuzhilin, A. S.; Gololobova, E. G.

2008-08-01

The effects of the concentration, temperature, and potential at the hydroxide/electrolyte interface on the aluminum hydroxide dissolution in sulfuric, hydrochloric, and perchloric acids are studied. The limiting stage of the aluminum hydroxide dissolution in the acids is found to be the transition of the complexes that form on the aluminum hydroxide surface from the solid phase into the solution. The results of the calculation of the acid-base equilibrium constants at the oxide (hydroxide)/solution interface using the experimental data on the potentiometric titration of Al2O3 and AlOOH suspensions are analyzed. A mechanism is proposed for the dissolution of aluminum hydroxides in acid media.

A prospective clinical trial on the influence of a triamcinolone/demeclocycline and a calcium hydroxide based temporary cement on pain perception

Directory of Open Access Journals (Sweden)

Willershausen Brita

2012-03-01

Full Text Available Abstract Introduction The aim of this clinical trial was to compare the degree of short term post-operative irritation after application of a triamcinolone/demeclocycyline based or a calcium hydroxide based provisional cement. Methods A total of 109 patients (55 female and 54 male; mean age: 51 ± 14 years with primary or secondary dentinal caries were randomly assigned to the two treatment groups of this biomedical clinical trial (phase III. Selection criteria were good systemic health and treated teeth, which were vital and showed no symptoms of pulpitis. Up to three teeth were prepared for indirect metallic restorations, and the provisional restorations were cemented with a triamcinolone/demeclocycyline (Ledermix or a calcium hydroxide (Provicol based material. The intensity of post-operative pain experienced was documented according to the VAS (4, 12, 20, 24, and 82 h and compared to VAS baseline. Results A total of 159 teeth were treated (Ledermix: 83 teeth, Provicol: 76 teeth. The minor irritation of the teeth, experienced prior to treatment, was similar in both groups; however, 4 h after treatment this value was significantly higher in the Provicol group than in the Ledermix group (p Conclusions The patients had no long term post-operative pain experience in both groups. However, within the first hours after cementation the sensation of pain was considerably higher in the Provicol group than in the Ledermix group.

Characteristics of Solid-State Calcium Ion Sensors Based on Photocurable and Selfplasticising Polyacrylate Matrices

Directory of Open Access Journals (Sweden)

Lee Yook Heng

2017-11-01

Full Text Available New membrane materials based on cross-linked poly(n-butyl acrylate (nBA, have been used successfully as calcium ion-selective membranes. These membrane materials possess selfplasticising property and hence do not require plasticisers. The photocurability and good adhesion characteristics of these polymer matrices enable workable solid-state calcium ion sensors to be fabricated by simple photocure procedures employing the calcium ionophore ETH5234 and a lipophilic additive as ion sensing components. The calcium ion-selectivity of the sensors can be controlled by varying the chemical composition of the photocured  membrane. An optimum amount of the cross-linker 2,2-hexanedioldiacrylate (HDDA and the incorporation of n-heptyl acrylate (nHA led to improvement in the calcium ion-selectivity. The best calcium ion-selectivity was obtained from a copolymer membrane with composition: nBA = 74 wt-%, nHA = 20 wt-% and HDDA = 0.1 wt-%. The selectivity coefficients of calcium over major cations were: LogKCaPot,Na= -4.4,  LogKCaPot,K = -3.6, LogKCa,PotLi = -5.9, LogKCaPot,Mg= -4.4 with a Nernstian slope (29.1 ± 0.8 mV/decade under buffered conditions. This potentiometric performance is comparable to other solid-state calcium ion sensors with various plasticised polymer membranes.

Periodontal and endodontic infectious/inflammatory profile in primary periodontal lesions with secondary endodontic involvement after a calcium hydroxide-based intracanal medication.

Science.gov (United States)

Duque, Thais M; Prado, Maira; Herrera, Daniel R; Gomes, Brenda P F A

2018-03-23

The aim of the present study was to investigate the effects of a calcium hydroxide-based intracanal medication (ICM) on periodontal and endodontic infectious/inflammatory contents and on periodontal clinical parameters in teeth with primary periodontal lesion and secondary endodontic involvement. Ten patients with abnormal pulp test results and deep probing depth derived from primary periodontal disease with secondary endodontic involvement were included. Samples were collected from root canals (RC) and periodontal pockets (PP) in order to investigate the microbiological status, levels of endotoxin (LPS), cytokines, and matrix metalloproteinases (MMP), before and after ICM. PCR was used for microbiological assessment. The kinetic-chromogenic LAL assay was used for LPS quantification. Quantikine ELISA kits were used for measurement of IL-1 α, IL-1 β, TNF-α, PGE 2 , MMP-2, MMP-3, MMP-8, MMP-9, and MMP-13 levels. The statistical analyses were made using the Friedman and Wilcoxon tests (p  0.05); however, the levels of the other MMPs and cytokines were reduced (p < 0.05). After 1 year of the root canal treatment, tooth mobility was significantly reduced (p ≤ 0.05). The use of a calcium hydroxide-based ICM showed positive effects for periodontal treatment prognosis, as it reduced LPS, cytokine, and MMP levels in periodontal pockets. Patients presenting deep probing depth and undergoing periodontal treatment for at least 6 months, with no positive response to periodontal therapy, might benefit with the endodontic treatment.

MTA and calcium hydroxide for pulp capping MTA e hidróxido de cálcio para proteção pulpar direta

Directory of Open Access Journals (Sweden)

Alexandra Mussolino de Queiroz

2005-06-01

Full Text Available This study evaluated the biocompatibility of mineral trioxide aggregate (MTA after direct capping of exposed pulp tissue in dog's teeth. Class I cavities were prepared in 26 teeth from 3 adult dogs. MTA was applied over the exposed pulp in 13 teeth and paste of calcium hydroxide plus distilled water (control was applied in the remaining 13 teeth. After 90 days, the animals were killed; the maxilla and mandible were dissected and sectioned to obtain individual roots. The samples were processed histologically. The pulp and periapical response observed with the use of MTA was similar to that of calcium hydroxide paste. In all specimens, there was a dentin bridge obliterating the exposure, an intact odontoblastic layer, no inflammatory cells, normal connective pulp tissue, normal apical and periapical regions and no bone tissue changes. Similar to calcium hydroxide, MTA presented excellent response when used for direct pulp capping.O objetivo deste trabalho foi avaliar a biocompatibilidade do agregado de trióxido mineral (MTA, após proteção pulpar direta em dentes de cães. Foram preparadas cavidades de Classe I, em 26 dentes de 3 cães adultos. O MTA foi aplicado sobre 13 dentes e a pasta de hidróxido de cálcio (grupo controle foi aplicada sobre os 13 dentes remanescentes. Após 90 dias, os animais foram mortos, a maxila e a mandíbula foram dissecadas e os dentes foram seccionados para obtenção de raízes individualizadas. Os espécimes foram processados histologicamente. A resposta do tecido pulpar e periapical foi semelhante para o MTA e o hidróxido de cálcio. Em todos os espécimes havia ponte de dentina obliterando o local da exposição pulpar, camada odontoblástica íntegra, ausência de células inflamatórias, tecido pulpar normal, e ausência de alterações na região periapical e óssea. Da mesma maneira que o hidróxido de cálcio, o MTA apresentou excelente biocompatibilidade quando usado para proteção pulpar direta.

Evaluation of layered zinc hydroxide nitrate and zinc/nickel double hydroxide salts in the removal of chromate ions from solutions

Science.gov (United States)

de Oliveira, Henrique Bortolaz; Wypych, Fernando

2016-11-01

Layered zinc hydroxide nitrate (ZnHN) and Zn/Ni layered double hydroxide salts were synthesized and used to remove chromate ions from solutions at pH 8.0. The materials were characterized by many instrumental techniques before and after chromate ion removal. ZnHN decomposed after contact with the chromate solution, whereas the layered structure of Zn/Ni hydroxide nitrate (Zn/NiHN) and Zn/Ni hydroxide acetate (Zn/NiHA) remained their layers intact after the topotactic anionic exchange reaction, only changing the basal distances. ZnHN, Zn/NiHN, and Zn/NiHA removed 210.1, 144.8, and 170.1 mg of CrO42-/g of material, respectively. Although the removal values obtained for Zn/NiHN and Zn/NiHA were smaller than the values predicted for the ideal formulas of the solids (194.3 and 192.4 mg of CrO42-/g of material, respectively), the measured capacities were higher than the values achieved with many materials reported in the literature. Kinetic experiments showed the removal reaction was fast. To facilitate the solid/liquid separation process after chromium removal, Zn/Ni layered double hydroxide salts with magnetic supports were also synthesized, and their ability to remove chromate was evaluated.

Solid State Characterization of Commercial Crystalline and Amorphous Atorvastatin Calcium Samples

OpenAIRE

Shete, Ganesh; Puri, Vibha; Kumar, Lokesh; Bansal, Arvind K.

2010-01-01

Atorvastatin calcium (ATC), an anti-lipid BCS class II drug, is marketed in crystalline and amorphous solid forms. The objective of this study was to perform solid state characterization of commercial crystalline and amorphous ATC drug samples available in the Indian market. Six samples each of crystalline and amorphous ATC were characterized using X-ray powder diffractometry (XRPD), differential scanning calorimetry (DSC), thermogravimetric analysis, Karl Fisher titrimetry, microscopy (hot s...

Hydroxide catalysts for lignin depolymerization

Science.gov (United States)

Beckham, Gregg T; Biddy, Mary J.; Kruger, Jacob S.; Chmely, Stephen C.; Sturgeon, Matthew

2017-10-17

Solid base catalysts and their use for the base-catalyzed depolymerization (BCD) of lignin to compounds such as aromatics are presented herein. Exemplary catalysts include layered double hydroxides (LDHs) as recyclable, heterogeneous catalysts for BCD of lignin.

Hydroxide catalysts for lignin depolymerization

Energy Technology Data Exchange (ETDEWEB)

Beckham, Gregg T.; Biddy, Mary J.; Chmely, Stephen C.; Sturgeon, Matthew

2017-04-25

Solid base catalysts and their use for the base-catalyzed depolymerization (BCD) of lignin to compounds such as aromatics are presented herein. Exemplary catalysts include layered double hydroxides (LDHs) as recyclable, heterogeneous catalysts for BCD of lignin.

A titration model for evaluating calcium hydroxide removal techniques

Directory of Open Access Journals (Sweden)

Mark PHILLIPS

2015-02-01

Full Text Available Objective Calcium hydroxide (Ca(OH2 has been used in endodontics as an intracanal medicament due to its antimicrobial effects and its ability to inactivate bacterial endotoxin. The inability to totally remove this intracanal medicament from the root canal system, however, may interfere with the setting of eugenol-based sealers or inhibit bonding of resin to dentin, thus presenting clinical challenges with endodontic treatment. This study used a chemical titration method to measure residual Ca(OH2 left after different endodontic irrigation methods. Material and Methods Eighty-six human canine roots were prepared for obturation. Thirty teeth were filled with known but different amounts of Ca(OH2 for 7 days, which were dissolved out and titrated to quantitate the residual Ca(OH2 recovered from each root to produce a standard curve. Forty-eight of the remaining teeth were filled with equal amounts of Ca(OH2 followed by gross Ca(OH2 removal using hand files and randomized treatment of either: 1 Syringe irrigation; 2 Syringe irrigation with use of an apical file; 3 Syringe irrigation with added 30 s of passive ultrasonic irrigation (PUI, or 4 Syringe irrigation with apical file and PUI (n=12/group. Residual Ca(OH2 was dissolved with glycerin and titrated to measure residual Ca(OH2 left in the root. Results No method completely removed all residual Ca(OH2. The addition of 30 s PUI with or without apical file use removed Ca(OH2 significantly better than irrigation alone. Conclusions This technique allowed quantification of residual Ca(OH2. The use of PUI (with or without apical file resulted in significantly lower Ca(OH2 residue compared to irrigation alone.

Nonsurgical Clinical Management of Periapical Lesions Using Calcium Hydroxide-Iodoform-Silicon-Oil Paste

Science.gov (United States)

Al Khasawnah, Qusai; Hassan, Fathi; Malhan, Deeksha; Engelhardt, Markus; Daghma, Diaa Eldin S.; Obidat, Dima; Lips, Katrin S.; Heiss, Christian

2018-01-01

Background The study aim is to avoid tooth extraction by nonsurgical treatment of periapical lesion. It assesses healing progress in response to calcium hydroxide-iodoform-silicon oil paste (CHISP). Numeric Pain Rating Scale was used to validate the approach. Furthermore, CHISP was used to treat cystic lesions secondary to posttraumatic avulsion of permanent teeth. Materials and Methods Over 200 patients with radicular cysts were treated with CHISP through the root canal. Radiographs were used to verify lesion size and position, ensure correct delivery to the site, and monitor the progress of bone healing in the lesion area. Ten males and 10 females were randomly selected for statistical assessment. Results No severe pain, complications, or failure in cyst healing was reported. Complete healing was achieved in an average of 75 days. Furthermore, healing of radicular cyst secondary to posttraumatic tooth avulsion was successful. Conclusion CHISP indicated an antiseptic effect, which enhanced and shortened healing time of periapical lesions. The less invasive procedure avoids tooth extraction and reduces bone resorption. Cyst management with CHISP can remedy failed root canal treatments. The results show a bone regenerative capacity of CHISP suggested in first rapid phase and a second slow phase. PMID:29619378

Determination of haloacetic acids in water using layered double hydroxides as a sorbent in dispersive solid-phase extraction followed by liquid chromatography with tandem mass spectrometry.

Science.gov (United States)

Alsharaa, Abdulnaser; Sajid, Muhammad; Basheer, Chanbasha; Alhooshani, Khalid; Lee, Hian Kee

2016-09-01

In the present study, highly efficient and simple dispersive solid-phase extraction procedure for the determination of haloacetic acids in water samples has been established. Three different types of layered double hydroxides were synthesized and used as a sorbent in dispersive solid-phase extraction. Due to the interesting behavior of layered double hydroxides in an acidic medium (pH˂4), the analyte elution step was not needed; the layered double hydroxides are simply dissolved in acid immediately after extraction to release the analytes which are then directly introduced into a liquid chromatography with tandem mass spectrometry system for analysis. Several dispersive solid-phase extraction parameters were optimized to increase the extraction efficiency of haloacetic acids such as temperature, extraction time and pH. Under optimum conditions, good linearity was achieved over the concentration range of 0.05-100 μg/L with detection limits in the range of 0.006-0.05 μg/L. The relative standard deviations were 0.33-3.64% (n = 6). The proposed method was applied to different water samples collected from a drinking water plant to determine the concentrations of haloacetic acids. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Alkali Silica Reaction In The Presence Of Metakaolin - The Significant Role of Calcium Hydroxide

Science.gov (United States)

Zapała-Sławeta, Justyna

2017-10-01

Reducing the internal corrosion, which is the result of reactions between alkalis and reactive aggregates is especially important in ensuring durability properties of concrete. One of the methods of inhibiting the reaction is using some mineral additives which have pozzolanic properties. This paper presents the efficacy of high-reactivity metakaolin in reducing expansion due to alkali-silica reaction. It was demonstrated that metakaolin in the amount from 5% to 20% by mass of Portland cement reduce linear expansion of mortar bars with opal aggregate. Nevertheless, the safe expansion level in the specimens, classified as non-destructive to concrete, was recorded for the mortars prepared with 20% addition of metakaolin. Depletion of free calcium hydroxide content was considered as one of the most beneficial effects of metakaolin in controlling alkali silica reaction. Based on thermogravimetric analysis (TGA) performed on mortar bars with and without metakaolin the differences in portlandite content were determined. Microstructural observation of the specimens containing metakaolin indicated the presence of a reaction products but fewer in number than those forming in the mortars without mineral additives.

Valorization of Calcium Carbonate-Based Solid Wastes for the Treatment of Hydrogen Sulfide from the Gas Phase

OpenAIRE

Pham Xuan , Huynh; Pham Minh , Doan; Galera Martinez , Marta; Nzihou , Ange; Sharrock , Patrick

2015-01-01

International audience; This paper focuses on the valorization of calcium carbonate-based solid wastes for theremoval of hydrogen sulfide from gas phase. Two solid wastes taken from industrial sites for theproduction of sodium carbonate and sodium bicarbonate by the Solvay process® were analyzedby different physico-chemical methods. Calcium carbonate was found as the main component ofboth the solid wastes. Trace amounts of other elements such as Mg, Al, Fe, Si, Cl, Na etc. werealso present in...

Aluminum Hydroxide and Magnesium Hydroxide

Science.gov (United States)

Aluminum Hydroxide, Magnesium Hydroxide are antacids used together to relieve heartburn, acid indigestion, and upset stomach. They ... They combine with stomach acid and neutralize it. Aluminum Hydroxide, Magnesium Hydroxide are available without a prescription. ...

Evaluation of a consolidation treatment in dolostones by mean of calcium hydroxide nanoparticles in high relative humidity conditions

International Nuclear Information System (INIS)

Gomez-Villalba, L. s.; Lopez-Arce, P.; Zornoza, A.; Alvares de Buergo, M.; Fort, R.

2011-01-01

In this article, the results of a treatment applied to dolomitic stones using an isopropyl colloidal solution based on calcium hydroxide nanoparticles with a concentration of 2.0g/l are presented. The consolidation process in the stone has been checked before and after 28 days of exposure to 75% relative humidity. Morphologic and structural studies of the consolidating product confirmed the carbonation process. X ray diffraction, electron microscopy (TEM and ESEM), and electron diffraction carried out on the consolidating product have confirmed the transformation of portlandite phase to calcium carbonate polymorph, calcite, aragonite and vaterite. Petrophysical tests performed on the stone before and after the application of the product have shown the improvement in the physical and hydrical properties due to the increase in the ultrasound velocity and density of the material, and a decrease in the capillarity coefficient and open porosity without significant changes in colour and brightness. The application of the consolidating product in the proposed experimental conditions is a natural method, compatible with the petrological characteristics of the substrate, without secondary damages on the stone, being an effective method to improve the durability of carbonate stones. (Author) 26 refs.

The effectiveness of sodium hydroxide (NaOH) and sodium carbonate (Na2CO3) on the impurities removal of saturated salt solution

Science.gov (United States)

Pujiastuti, C.; Ngatilah, Y.; Sumada, K.; Muljani, S.

2018-01-01

Increasing the quality of salt can be done through various methods such as washing (hydro-extraction), re-crystallization, ion exchange methods and others. In the process of salt quality improvement by re-crystallization method where salt product diluted with water to form saturated solution and re-crystallized through heating process. The quality of the salt produced is influenced by the quality of the dissolved salt and the crystallization mechanism applied. In this research is proposed a concept that before the saturated salt solution is recrystallized added a chemical for removal of the impurities such as magnesium ion (Mg), calcium (Ca), potassium (K) and sulfate (SO4) is contained in a saturated salt solution. The chemical reagents that used are sodium hydroxide (NaOH) 2 N and sodium carbonate (Na2CO3) 2 N. This research aims to study effectiveness of sodium hydroxide and sodium carbonate on the impurities removal of magnesium (Mg), calcium (Ca), potassium (K) and sulfate (SO4). The results showed that the addition of sodium hydroxide solution can be decreased the impurity ions of magnesium (Mg) 95.2%, calcium ion (Ca) 45%, while the addition of sodium carbonate solution can decreased magnesium ion (Mg) 66.67% and calcium ion (Ca) 77.5%, but both types of materials are not degradable sulfate ions (SO4). The sodium hydroxide solution more effective to decrease magnesium ion than sodium carbonate solution, and the sodium carbonate solution more effective to decrease calcium ion than sodium hydroxide solution.

Comparing the reinforcing effects of a resin modified glassionomer cement, Flowable compomer, and Flowable composite in the restoration of calcium hydroxide-treated immature roots in vitro

Directory of Open Access Journals (Sweden)

S Prathibha Rani

2011-01-01

Full Text Available One hundred and sixty human permanent central incisors were enlarged to a 120 file size after crown removal procedure to simulate immature teeth. The root canals were filled with calcium hydroxide and stored for 15 days (phase I, 30 days (phase II, 90 days (phase III, and 180 days (Phase IV. At the end of these selected time periods, calcium hydroxide was cleaned off the root canals of forty teeth that were randomly selected and obturated with gutta-percha points in the apical 2 mm of the root canals with a sealer. The specimens were further equally divided into four groups. Unrestored Group I served as control and the root canals of teeth in the other three group specimens were reinforced with resin modified glassionomer cement (RMGIC (Group II, Flowable Compomer (Group III, and Flowable Composite (Group IV, respectively, using a translucent curing post. All specimens were subjected to compressive force using an Instron Testing machine, until fracture occurred. All the materials evaluated substantially reinforced the root specimens compared to the control. At the end of 180 days, Flowable composites showed maximum reinforcement compared to the other groups; however, no significant differences were found between the reinforcement capabilities of Flowable Compomer and RMGIC.

The effect of magnesium hydroxide, hydromagnesite and layered double hydroxide on the heat stability and fire performance of plasticized poly(vinyl chloride)

CSIR Research Space (South Africa)

Molefe, DM

2015-09-01

Full Text Available . The other samples contained, in addition, minor amounts of iron, manganese nickel and calcium as impurities. Table 2. XRF composition analysis data of samples roasted at 1000 C Concentration, wt.% SiO2 Al2O3 Fe2O3 MnO MgO CaO NiO MgAl-LDH 1.59 36.85 0... additives aluminium trihydrate, magnesium hydroxide (MH), hydromagnesite (HM) and layered double hydroxide (LDH) have utility as endothermic flame retardants and smoke suppressants for PVC as well as other polymers (10-14). Their flame retardant action...

Effectiveness of Various Irrigation Protocols in Removing Calcium Hydroxide from Root Canals

Directory of Open Access Journals (Sweden)

Hakan Göktürk

2018-04-01

Full Text Available Objective: The purpose of this study was to investigate the removal efficiency of calcium hydroxide (CH by CanalBrush, Vibringe, laser-activated irrigation (LAI, conventional syringe irrigation (CSI, XP-endo Finisher, and passive ultrasonic irrigation (PUI in the root canal walls. Materials and Methods: Ninety-eight human mandibular premolar teeth were prepared. Root canals were filled with CH. The roots were divided into six experimental groups (n=15/group according to the irrigation protocol used: group 1 (CSI, group 2 (Vibringe, group 3 (CanalBrush, group 4 (XP-endo Finisher, group 5 (PUI, and group 6 (LAI. The amount of residual CH in the canal walls for each canal third was scored. Data were analysed by using Kruskal-Wallis and Bonferroni-correction Mann-Whitney U tests. Results: None of the investigated protocols renders the root canal walls free of CH remnants. Significant differences were found between tooth regions in terms of CH removal (p<0.05, and all groups except group 6 (LAI showed more residual CH in the apical region. PUI and LAI eliminated significantly more CH than CSI from the middle and apical thirds of the root canal, respectively. Conclusion: The activation of sodium hypochlorite with various devices increased CH removal at the apical and middle part of the canal. LAI and PUI produce better results in the apical and middle thirds, respectively.

Subcutaneous tissue reaction to castor oil bean and calcium hydroxide in rats

Directory of Open Access Journals (Sweden)

Samira Esteves Afonso Camargo

2010-06-01

Full Text Available Castor oil bean cement (COB is a new material that has been used as an endodontic sealer, and is a candidate material for direct pulp capping. OBJECTIVE: The purpose of this study was to evaluate the biocompatibility of a new formulation of COB compared to calcium hydroxide cement (CH and a control group without any material, in the subcutaneous tissue of rats. MATERIAL AND METHODS: The materials were prepared, packed into polyethylene tubes, and implanted in the rat dorsal subcutaneous tissue. Animals were sacrificed at the 7th and 50th days after implantation. A quantitative analysis of inflammatory cells was performed and data were subjected to ANOVA and Tukey's tests at 5% significance level. RESULTS: Comparing the mean number of inflammatory cells between the two experimental groups (COB and CH and the control group, statistically significant difference (p=0.0001 was observed at 7 and 50 days. There were no significant differences (p=0.111 between tissue reaction to CH (382 inflammatory cells and COB (330 inflammatory cells after 7 days. After 50 days, significantly more inflammatory cells (p=0.02 were observed in the CH group (404 inflammatory cells than in the COB group (177 inflammatory cells. CONCLUSIONS: These results demonstrate that the COB cement induces less inflammatory response within long periods.

Production of the Lax Ca1-x Cry Al1-y O3 compound through hydroxide precipitation

International Nuclear Information System (INIS)

Martins, L.C.; Machado, A.J.S.

1996-01-01

Purposing to reduce the cost of preparation of the lanthanum chromite doped with calcium and aluminum, it was made a study of the condition of hydroxide precipitation, using calcium, chromium and aluminum nitrates and lanthanum oxide, as precursors and as precipitate agent was used potassium hydroxide. In this study are showed results about the reaction kinetic, x-ray diffraction and yield as function of the pH. These results suggest a high yield for also elements studied. The phase of stoichiometry, La 0.8 Ca 0.2 Cr 0.75 Al 0.25 O 3 was obtained in low temperature. In fact, this process is viable to produce of lanthanum chromite doped with calcium and aluminum. (author)

Nonsurgical Clinical Management of Periapical Lesions Using Calcium Hydroxide-Iodoform-Silicon-Oil Paste

Directory of Open Access Journals (Sweden)

Qusai Al Khasawnah

2018-01-01

Full Text Available Background. The study aim is to avoid tooth extraction by nonsurgical treatment of periapical lesion. It assesses healing progress in response to calcium hydroxide-iodoform-silicon oil paste (CHISP. Numeric Pain Rating Scale was used to validate the approach. Furthermore, CHISP was used to treat cystic lesions secondary to posttraumatic avulsion of permanent teeth. Materials and Methods. Over 200 patients with radicular cysts were treated with CHISP through the root canal. Radiographs were used to verify lesion size and position, ensure correct delivery to the site, and monitor the progress of bone healing in the lesion area. Ten males and 10 females were randomly selected for statistical assessment. Results. No severe pain, complications, or failure in cyst healing was reported. Complete healing was achieved in an average of 75 days. Furthermore, healing of radicular cyst secondary to posttraumatic tooth avulsion was successful. Conclusion. CHISP indicated an antiseptic effect, which enhanced and shortened healing time of periapical lesions. The less invasive procedure avoids tooth extraction and reduces bone resorption. Cyst management with CHISP can remedy failed root canal treatments. The results show a bone regenerative capacity of CHISP suggested in first rapid phase and a second slow phase.

Local environment and composition of magnesium gallium layered double hydroxides determined from solid-state 1H and 71Ga NMR spectroscopy

DEFF Research Database (Denmark)

Boisen Staal, Line; Lipton, Andrew S.; Zorin, Vadim

2014-01-01

Ordering of gallium(III) in a series of magnesium gallium (MgGa) layered double hydroxides (LDHs), [Mg1−xGax(OH)2(NO3)x·yH2O] was investigated using solid-state 1H and 71Ga NMR spectroscopy as well as powder X-ray diffraction. Three different proton environments from Mg3single bondOH, Mg2Gasingle...... analysis show that the synthesized MgGa LDH׳s had a lower Mg:Ga ratio than that of the starting reactant solution. The origin of this is the formation of soluble [Ga(OH)4]− complexes formed during synthesis, and not due to formation of insoluble gallium (oxy)hydroxides. No sign of Gasingle bondOsingle bond...

Action of Chlorhexidine, Zingiber officinale, and Calcium Hydroxide on Candida albicans, Enterococcus faecalis, Escherichia coli, and Endotoxin in the Root Canals.

Science.gov (United States)

Valera, Marcia C; Oliveira, Sarah Ac; Maekawa, Lilian E; Cardoso, Flávia Gr; Chung, Adriana; Silva, Stephanie Fp; Carvalho, Cláudio At

2016-02-01

The purpose of this in vitro study was to evaluate the antimicrobial activity of 2% chlorhexidine gel (CHX) as auxiliary chemical substance and intracanal medications on Candida albicans, Enterococcus faecalis, Escherichia coli, and their endotoxins in the root canals. The study was conducted on 48 single-rooted human teeth divided into four groups (n = 12), according to intracanal medications used: (1) Calcium hydroxide + apyrogenic saline solution (Ca(OH)2 + SS), (2) 20% ginger glycolic extract (GEN), (3) calcium hydroxide + 20% ginger glycolic extract (Ca(OH)2 + GEN), (4) apyrogenic SS (control). Collections were made from the root canal content before preparation (baseline-S1), immediately after instrumentation (S2), 7 days after instrumentation (S3), after 14 days the action of intracanal medication (S4), and 7 days after removal of the intracanal medication (S5). The antimicrobial activity and endotoxin content were analyzed for all collections. The results were statistically analyzed by the Kruskal-Wallis and Dunn tests at a significance level of 5%. After instrumentation with CHX, there was complete elimination of E. coli and C. albicans, except for E. faecalis, which was significantly reduced and then completely eliminated after intracanal medication. There was significant reduction of endotoxin after instrumentation. Comparison of collection after instrumentation and intracanal medication revealed reduction of endotoxins in all groups; this reduction was greater in group Ca(OH)2 followed by the group GEN. It was concluded that the instrumentation using CHX and intracanal medication used were able to eliminate the microorganisms from the root canal; the endotoxins were reduced, yet not completely eliminated. This study is important and relevant for searching alternatives during endodontic therapy, since it aims to study the effect of Zingiber officinale on microorganisms and endotoxins present in root canals.

Carbon-Based Solid-State Calcium Ion-Selective Microelectrode and Scanning Electrochemical Microscopy: A Quantitative Study of pH-Dependent Release of Calcium Ions from Bioactive Glass.

Science.gov (United States)

Ummadi, Jyothir Ganesh; Downs, Corey J; Joshi, Vrushali S; Ferracane, Jack L; Koley, Dipankar

2016-03-15

Solid-state ion-selective electrodes are used as scanning electrochemical microscope (SECM) probes because of their inherent fast response time and ease of miniaturization. In this study, we report the development of a solid-state, low-poly(vinyl chloride), carbon-based calcium ion-selective microelectrode (Ca(2+)-ISME), 25 μm in diameter, capable of performing an amperometric approach curve and serving as a potentiometric sensor. The Ca(2+)-ISME has a broad linear response range of 5 μM to 200 mM with a near Nernstian slope of 28 mV/log[a(Ca(2+))]. The calculated detection limit for Ca(2+)-ISME is 1 μM. The selectivity coefficients of this Ca(2+)-ISME are log K(Ca(2+),A) = -5.88, -5.54, and -6.31 for Mg(2+), Na(+), and K(+), respectively. We used this new type of Ca(2+)-ISME as an SECM probe to quantitatively map the chemical microenvironment produced by a model substrate, bioactive glass (BAG). In acidic conditions (pH 4.5), BAG was found to increase the calcium ion concentration from 0.7 mM ([Ca(2+)] in artificial saliva) to 1.4 mM at 20 μm above the surface. In addition, a solid-state dual SECM pH probe was used to correlate the release of calcium ions with the change in local pH. Three-dimensional pH and calcium ion distribution mapping were also obtained by using these solid-state probes. The quantitative mapping of pH and Ca(2+) above the BAG elucidates the effectiveness of BAG in neutralizing and releasing calcium ions in acidic conditions.

Precursor preparation for Ca-Al layered double hydroxide to remove hexavalent chromium coexisting with calcium and magnesium chlorides

Science.gov (United States)

Zhong, Lihua; He, Xiaoman; Qu, Jun; Li, Xuewei; Lei, Zhiwu; Zhang, Qiwu; Liu, Xinzhong

2017-01-01

Al(OH)3 and Ca(OH)2 powders are co-ground to prepare a precursor which hydrates into a layered double hydroxide (LDH) phase by agitation in aqueous solution with target hexavalent chromium (Cr(VI)) at room temperature, to achieve an obvious improvement in removal efficiency of Cr(VI) through an easy incorporation into the structure. Although the prepared precursor transforms into LDH phases also when agitated in the solutions of calcium and magnesium chlorides, it incorporates Cr(VI) preferentially to the chloride salts when they coexist. The adsorption isotherm and kinetic studies show that the phenomena occurring on the Al-Ca precursor fit a pseudo-second-order kinetics with a Langmuir adsorption capacity of 59.45 mg/g. Besides, characterizations of the prepared precursor and the samples after adsorption are also performed by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), Transmission electron microscope (TEM) to understand the reason of the preferential incorporation of Cr(VI) to the coexisting chloride salts during the LDH phase formation. Ca-Al precursor (C3A) was agitated in a hexavalent chromium (Cr(VI)) solution to form Al-Ca-CrO4 LDH product. Ca-Al-CrO4 LDH phase occurred preferentially to Ca-Al-MCl2 LDH phases in the solutions of calcium and magnesium chlorides, it incorporates Cr(VI) preferentially to the chloride salts when they coexist.

REGIOSELECTIVE REACTIONS OF 3-ALKYL-1-PHENYL-2-PYRAZOLIN-5-ONES WITH ACYL HALIDES IN THE PRECENCE OF NONOSIZED MAGNESIUM HYDROXIDE AS A HIGHLY EFFECTIVE HETEROGENOUS BASE CATALYST Regioselektive Reaktionen von 3-Alkyl-1-PHENYL-2-pyrazolin-5-ONES Mit Acylhalogeniden IN DER PRECENCE DER NONOSIZED MAGNESIUM HYDROXIDE als hochwirksame heterogene BASE CATALYST

OpenAIRE

Hassan Sheibani and Bahman Massomi Nejad

2012-01-01

4-Acyl-3-alkyl-1-phenyl-2-pyrazolin-5-one derivatives were prepared by the regioselective acylation of 3-alkyl-1-phenyl-2-pyrazolin-5-ones in the presence of base catalysts such as calcium hydroxide [Ca(OH)2], magnesium hydroxide [Mg(OH)2] and nanosized magnesium hydroxide. In the presence of nanosized magnesium hydroxide, excellent yields of products were obtained and reaction times were significantly reduced.

Studies on Pu(IV)/(III)-oxalate precipitation from nitric acid containing high concentration of calcium and fluoride ions

International Nuclear Information System (INIS)

Kalsi, P.K.; Pawar, S.M.; Ghadse, D.R.; Joshi, A.R.; Ramakrishna, V.V.; Vaidya, V.N.; Venugopal, V.

2003-01-01

Plutonium (IV)/(III) oxalate precipitation from nitric acid solution, containing large amount of calcium and fluoride ions was investigated. It was observed that direct precipitation of Pu (IV) oxalate from nitric acid containing large amount of calcium and fluoride ions did not give good decontamination of Pu from calcium and fluoride impurities. However, incorporation of hydroxide precipitation using ammonium hydroxide prior to Pu (IV) oxalate precipitation results into PuO 2 with much less calcium and fluoride impurities. Whereas, good decontamination from calcium and fluoride impurities could be obtained by employing Pu (III) oxalate precipitation directly from nitric acid containing large amount of calcium and fluoride ions. A method was also developed to recover Pu from the oxalate waste containing calcium and fluoride ions. (author)

Neutralization of Hydroxide Ion in Melt-Grown NaCl Crystals

Science.gov (United States)

Otterson, Dumas A.

1961-01-01

Many recent studies of solid-state phenomena, particularly in the area of crystal imperfections, have involved the use of melt-grown NaCl single crystals. Quite often trace impurities in these materials have had a prominent effect on these phenomena. Trace amounts of hydroxide ion have been found in melt-grown NaCl crystals. This paper describes a nondestructive method of neutralizing the hydroxide ion in such crystals. Crystals of similar hydroxide content are maintained at an elevated temperature below the melting point of NaCl in a flowing atmosphere containing. dry hydrogen chloride. Heat treatment is continued until an analysis of the test specimens shows no excess hydroxide ion. A colorimetric method previously described4 is used for this analysis.

Assessment of a synchrotron X-ray method for quantitative analysis of calcium hydroxide

International Nuclear Information System (INIS)

Williams, P. Jason; Biernacki, Joseph J.; Bai Jianming; Rawn, Claudia J.

2003-01-01

Thermogravimetric analysis (TGA) and quantitative X-ray diffraction (QXRD) are widely used to determine the calcium hydroxide (CH) content in cementitious systems containing blends of Portland cement, fly ash, blast furnace slag, silica fume and other pozzolanic and hydraulic materials. These techniques, however, are destructive to cement samples and subject to various forms of error. While precise weight losses can be measured by TGA, extracting information from samples with multiple overlapping thermal events is difficult. And, however, while QXRD can offer easier deconvolution, the accuracy for components below about 5 wt.% is typically poor when a laboratory X-ray source is used. Furthermore, the destructive nature of both techniques prevents using them to study the in situ hydration of a single contiguous sample for kinetic analysis. In an attempt to overcome these problems, the present research evaluated the use of synchrotron X-rays for quantitative analysis of CH. A synchrotron X-ray source was used to develop calibration data for quantification of the amount of CH in mixtures with fly ash. These data were compared to conventional laboratory XRD data for like samples. While both methods were found to offer good quantification, synchrotron XRD (SXRD) provided a broader range of detectability and higher accuracy than laboratory diffraction and removed the subjectivity as compared to TGA analysis. Further, the sealed glass capillaries used with the synchrotron source provided a nondestructive closed, in situ environment for tracking hydrating specimens from zero to any desired age

The effects of lithium hydroxide solution on alkali silica reaction gels created with opal

International Nuclear Information System (INIS)

Mitchell, Lyndon D.; Beaudoin, James J.; Grattan-Bellew, Patrick

2004-01-01

The reaction of Nevada opal with calcium hydroxide, potassium hydroxide and lithium hydroxide solutions was investigated. In addition, opal was exposed to a combined solution of these three hydroxides. The progress of the three reactions was followed using X-ray diffraction (XRD), 29 Si nuclear magnetic resonance (NMR) and scanning electron microscopy (SEM). The XRD results indicated the presence of a low-angle peak exclusive to the lithium-based reactions. The NMR results suggested a change in the silicate structure in the presence of lithium. These techniques indicated that the reaction of the alkali with the opal starting material is inhibited and perhaps stopped in the presence of lithium hydroxide. SEM revealed that the morphology of the reaction products on the surface of the reacted opal grains is markedly different invariably. It was concluded that evidence to support the theory of a protective layer exists and that the nature of the layer varies with ion type

Important role of calcium chloride in preventing carbon monoxide generation during desflurane degradation with alkali hydroxide-free carbon dioxide absorbents.

Science.gov (United States)

Ando, Takahiro; Mori, Atsushi; Ito, Rie; Nishiwaki, Kimitoshi

2017-12-01

We investigated whether calcium chloride (CaCl 2 ), a supplementary additive in carbon dioxide (CO 2 ) absorbents, could affect carbon monoxide (CO) production caused by desflurane degradation, using a Japanese alkali-free CO 2 absorbent Yabashi Lime ® -f (YL-f), its CaCl 2 -free and 1% CaCl 2 -added derivatives, and other commercially available alkali-free absorbents with or without CaCl 2 . The reaction between 1 L of desflurane gas (3-10%) and 20 g of desiccated specimen was performed in an artificial closed-circuit anesthesia system for 3 min at 20 or 40 °C. The CO concentration was measured using a gas chromatograph equipped with a semiconductor sensor detector. The systems were validated by detecting dose-dependent CO production with an alkali hydroxide-containing CO 2 absorbent, Sodasorb ® . Compared with YL-f, the CaCl 2 -free derivative caused the production of significantly more CO, while the 1% CaCl 2 -added derivative caused the production of a comparable amount of CO. These phenomena were confirmed using commercially available absorbents AMSORB ® PLUS, an alkali-free absorbent with CaCl 2 , and LoFloSorb™, an alkali-free absorbent without CaCl 2 . These results suggest that CaCl 2 plays an important role in preventing CO generation caused by desflurane degradation with alkali hydroxide-free CO 2 absorbents like YL-f.

Solid-state chelation of metal ions by ethylenediaminetetraacetate intercalated in a layered double hydroxide.

Science.gov (United States)

Tarasov, Konstantin A; O'Hare, Dermot; Isupov, Vitaly P

2003-03-24

The solid-state chelation of transition metal ions (Co(2+), Ni(2+), and Cu(2+)) from aqueous solutions into the lithium aluminum layered double hydroxide ([LiAl(2)(OH)(6)]Cl x 0.5H(2)O or LDH) which has been pre-intercalated with EDTA (ethylenediaminetetraacetate) ligand has been investigated. The intercalated metal cations form [M(edta)](2)(-) complexes between the LDH layers as indicated by elemental analysis, powder X-ray diffraction, and IR and UV-vis spectroscopies. If metal chloride or nitrate salts are used in the reaction with the LDH then co-intercalation of either the Cl(-) or NO(3)(-) anions is observed. In the case of metal acetate salts the cations intercalate without the accompanying anion. This can be explained by the different intercalation selectivity of the anions in relation to the LDH. In the latter case the introduction of the positive charge into LDH structure was compensated for by the release from the solid of the equivalent quantity of lithium and hydrogen cations. Time-resolved in-situ X-ray diffraction measurements have revealed that the chelation/intercalation reactions proceed very quickly. The rate of the reaction found for nickel acetate depends on concentration as approximately k[Ni(Ac)(2)](3).

40 CFR 268.42 - Treatment standards expressed as specified technologies.

Science.gov (United States)

2010-07-01

... such as copper, zinc, nickel, gold, and sulfur that result in a nonliquid, semi-solid amalgam and..., hydroxides, carbonates, sulfides, sulfates, chlorides, flourides, or phosphates. The following reagents (or... hydroxides of calcium and/or magnesium; (2) caustic (i.e., sodium and/or potassium hydroxides; (3) soda ash...

Calcium phosphate bioceramics prepared from wet chemically precipitated powders

Directory of Open Access Journals (Sweden)

Kristine Salma

2010-03-01

Full Text Available In this work calcium phosphates were synthesized by modified wet chemical precipitation route. Contrary to the conventional chemical precipitation route calcium hydroxide was homogenized with planetary mill. Milling calcium oxide and water in planetary ball mill as a first step of synthesis provides a highly dispersed calcium hydroxide suspension. The aim of this work was to study the influence of main processing parameters of wet chemical precipitation synthesis product and to control the morphology, phase and functional group composition and, consequently, thermal stability and microstructure of calcium phosphate bioceramics after thermal treatment. The results showed that it is possible to obtain calcium phosphates with different and reproducible phase compositions after thermal processing (hydroxyapatite [HAp], β-tricalcium phosphate [β-TCP] and HAp/β-TCP by modified wet-chemical precipitation route. The β-TCP phase content in sintered bioceramics samples is found to be highly dependent on the changes in technological parameters and it can be controlled with ending pH, synthesis temperature and thermal treatment. Pure, crystalline and highly thermally stable (up to 1300°C HAp bioceramics with homogenous grainy microstructure, grain size up to 200–250 nm and high open porosity can be successfully obtained by powder synthesized at elevated synthesis temperature of 70°C and stabilizing ending pH at 9.

The effect of peracetic acid on removing calcium hydroxide from the root canals.

Science.gov (United States)

Sağsen, Burak; Ustün, Yakup; Aslan, Tuğrul; Canakçi, Burhan Can

2012-09-01

The goal of this study was to evaluate the efficiencies of different irrigation solutions in the removal of calcium hydroxide (CH). Forty-eight maxillary central incisor teeth were used. Root canals were prepared with the ProTaper system (Dentsply Maillefer, Baillagues, Switzerland). Five milliliters 2% NaOCl, 5 mL 17% EDTA, and 10 mL saline were used for final irrigation. The canals were filled with CH paste. Specimens were randomly divided into 4 experimental groups (n = 10) according to irrigation protocols. Positive and negative control groups (n = 4) were used. Group 1 used 2.5 mL 17% EDTA, group 2 used 2.5 mL 2.5% NaOCl + 2.5 mL 17% EDTA, group 3 used 2.5 mL 1% peracetic acid (PAA), and group 4 used 2.5 mL 0.5% PAA. The specimens were evaluated with scanning electron microscope analysis and scored. Kruskal-Wallis and Student Newman-Keuls post hoc tests were used for statistical analysis. In the apical thirds, 1% PAA was superior to the other groups (P .05). In the middle thirds, no significant differences were found among the groups (P > .05). In the coronal thirds, 1% PAA was superior to the other groups. There were significant differences among all the other groups (P < .05). According to the findings of the present study, 1% PAA could be recommended for the removal of CH from the root canals. Crown Copyright © 2012. Published by Elsevier Inc. All rights reserved.

Interaction between calcium and phosphate adsorption on goethite.

Science.gov (United States)

Rietra, R P; Hiemstra, T; van Riemsdijk, W H

2001-08-15

Quantitatively, little is known about the ion interaction processes that are responsible for the binding of phosphate in soil, water, and sediment, which determine the bioavailability and mobility of phosphate. Studies have shown that metal hydroxides are often responsible for the binding of PO4 in soils and sediments, but the binding behavior of PO4 in these systems often differs significantly from adsorption studies on metal hydroxides in laboratory. The interaction between PO4 and Ca adsorption was studied on goethite because Ca can influence the PO4 adsorption equilibria. Since adsorption interactions are very difficult to discriminate from precipitation reactions, conditions were chosen to prevent precipitation of Ca-PO4 solids. Adsorption experiments of PO4 and Ca, individually and in combination, show a strong interaction between adsorbed Ca and PO4 on goethite for conditions below the saturation index of apatite. It is shown that it is possible to predict the adsorption and interaction of PO4 and Ca on electrostatic arguments using the model parameter values derived from the single-ion systems and without invoking ternary complex formation or precipitation. The model enables the prediction of the Ca-PO4 interaction for environmentally relevant calcium and phosphate concentrations.

Predictive Mechanical Characterization of Macro-Molecular Material Chemistry Structures of Cement Paste at Nano Scale - Two-phase Macro-Molecular Structures of Calcium Silicate Hydrate, Tri-Calcium Silicate, Di-Calcium Silicate and Calcium Hydroxide

Science.gov (United States)

Padilla Espinosa, Ingrid Marcela

Concrete is a hierarchical composite material with a random structure over a wide range of length scales. At submicron length scale the main component of concrete is cement paste, formed by the reaction of Portland cement clinkers and water. Cement paste acts as a binding matrix for the other components and is responsible for the strength of concrete. Cement paste microstructure contains voids, hydrated and unhydrated cement phases. The main crystalline phases of unhydrated cement are tri-calcium silicate (C3S) and di-calcium silicate (C2S), and of hydrated cement are calcium silicate hydrate (CSH) and calcium hydroxide (CH). Although efforts have been made to comprehend the chemical and physical nature of cement paste, studies at molecular level have primarily been focused on individual components. Present research focuses on the development of a method to model, at molecular level, and analysis of the two-phase combination of hydrated and unhydrated phases of cement paste as macromolecular systems. Computational molecular modeling could help in understanding the influence of the phase interactions on the material properties, and mechanical performance of cement paste. Present work also strives to create a framework for molecular level models suitable for potential better comparisons with low length scale experimental methods, in which the sizes of the samples involve the mixture of different hydrated and unhydrated crystalline phases of cement paste. Two approaches based on two-phase cement paste macromolecular structures, one involving admixed molecular phases, and the second involving cluster of two molecular phases are investigated. The mechanical properties of two-phase macromolecular systems of cement paste consisting of key hydrated phase CSH and unhydrated phases C3S or C2S, as well as CSH with the second hydrated phase CH were calculated. It was found that these cement paste two-phase macromolecular systems predicted an isotropic material behavior. Also

Application of magnesium hydroxide and barium hydroxide for the ...

African Journals Online (AJOL)

Application of magnesium hydroxide and barium hydroxide for the removal of metals and sulphate from mine water. ... equivalent to the Ba(OH)2 dosage. During CO2-dosing, CaCO3 is precipitated to the saturation level of CaCO3. Keywords: Magnesium hydroxide; barium hydroxide; sulphate removal; water treatment ...

Biocompatibility of bio based calcium carbonate nanocrystals ...

African Journals Online (AJOL)

Background: Currently, there has been extensive research interest for inorganic nanocrystals such as calcium phosphate, iron oxide, silicone, carbon nanotube and layered double hydroxide as a drug delivery system especially in cancer therapy. However, toxicological screening of such particles is paramount importance ...

Thermodynamic Properties of Alkali Metal Hydroxides. Part II. Potassium, Rubidium, and Cesium Hydroxides

International Nuclear Information System (INIS)

Gurvich, L.V.; Bergman, G.A.; Gorokhov, L.N.; Iorish, V.S.; Leonidov, V.Y.; Yungman, V.S.

1997-01-01

The data on thermodynamic and molecular properties of the potassium, rubidium and cesium hydroxides have been collected, critically reviewed, analyzed, and evaluated. Tables of the thermodynamic properties [C p circ , Φ=-(G -H(0)/T, S, H -H(0), Δ f H, Δ f G)] of these hydroxides in the condensed and gaseous states have been calculated using the results of the analysis and some estimated values. The recommendations are compared with earlier evaluations given in the JANAF Thermochemical Tables and Thermodynamic Properties of Individual Substances. The properties considered are: the temperature and enthalpy of phase transitions and fusion, heat capacities, spectroscopic data, structures, bond energies, and enthalpies of formation at 298.15 K. The thermodynamic functions in solid, liquid, and gaseous states are calculated from T=0 to 2000 K for substances in condensed phase and up to 6000 K for gases. copyright 1997 American Institute of Physics and American Chemical Society

Ion-exchange synthesis of compounds based on low-water niobium hydroxide

International Nuclear Information System (INIS)

Ivanova, N.E.; Sakharov, V.E.; Korovin, S.S.

1977-01-01

Ordinary physico-chemical methods have been used for studying the possibilities of the ion-exchange synthesis of niobates of alkaline and alkaline-earth elements based on low-water niobium hydroxide small at relatively low temperatures. It has been established that cation-exchange properties of low-water niobium hydroxide are revealed in a wide range of pH (from 8.95 to 12.4 for alkaline-earth elements and from 6.7 to 12.0 for alkaline elements). Physico-chemical study of solid phases points that there is a monophase with low-water niobium hydroxide. The rate of crystallization ageing of amorphous phases based on low-water niobium hydroxide is rather small for the samples with a M:Nb ratio less than 1.0 whereas mixed hydroxides with M:Nb ratio more than 1.0 reveal on X-ray diffraction patterns diffusion reflections after keeping in mother liquor for 5 hours-1 day

In vitro antimicrobial activity of root canal sealers and calcium hydroxide paste

Directory of Open Access Journals (Sweden)

Alessandro L Cavalcanti

2010-01-01

Full Text Available Aim: To evaluate the in vitro antimicrobial activity of different root canal sealers and calcium hydroxide (CH paste. Materials and Methods: The sample was composed of two sealers (Fill Canal® and Sealer 26® , one CH cement (Hydro C® , and a CH paste. The agar diffusion test was performed in Petri dishes inoculated with the following microorganisms: Streptococcus salivarius, Streptococcus oralis, Streptococcus mitis, Lactobacillus casei, Streptococcus mutans, Candida albicans, Candida krusei, and Candida tropicalis. The diameters of the zones of microbial growth inhibition were measured after 24 h. The tests were performed in triplicate. Data were analyzed statistically by ANOVA and Tukey′s test at 5% significance level. Results: Fill Canal® exhibited the largest mean zone of microbial growth inhibition against the Candida species and differed significantly from the other groups (P < 0.001. When inhibition was observed against S. mitis and S. oralis, the CH paste presented a larger mean zone of microbial growth inhibition than those of the other materials (P < 0.05. Regarding the inhibition of S. mutans, a statistically significant difference was observed only between the CH paste and Hydro C® (P < 0.05; the paste produced the largest mean zone of microbial growth inhibition against this microorganism. Regarding the inhibition of S. salivarius, Fill Canal® presented smaller mean zone of microbial growth inhibition than Sealer 26® and CH paste (P < 0.05. Conclusion: All the materials presented zones of microbial growth inhibition against all the test bacteria. Fill Canal® presented the largest mean zone of inhibition against the Candida species. For the Streptococcus cultures, none of the sealers presented inhibition superior to that of the CH paste.

The effect of dentin on the pulp tissue dissolution capacity of sodium hypochlorite and calcium hydroxide.

Science.gov (United States)

Slutzky-Goldberg, Iris; Hanut, Aiham; Matalon, Shlomo; Baev, Valery; Slutzky, Hagay

2013-08-01

Sodium hypochlorite (NaOCl) and calcium hydroxide (Ca[OH]2) have tissue dissolution capacity. The aim of this study was to evaluate the potential effect of dentin on their tissue dissolution capacity in a novel dentin model. Dentin models were prepared from 25 freshly extracted human molar teeth; the crowns were separated from the roots, and a rectangular inner shape was prepared. Pulp tissue samples adjusted to similar weights of 6.5 ± 0.2 mg were randomly divided into 6 groups: NaOCl groups in test tubes or dentin models for 1 hour, Ca(OH)2 groups in test tubes or dentin models for 1 week, and control groups saline in test tubes or dentin models for 1 week. The final weights after the experimental period were checked and compared with the initial weights. The differences were statistically analyzed. The tissue dissolution capacity of Ca(OH)2 was affected by the presence of dentin. Similarly, NaOCl lost its effect on the pulp tissue after incubation in dentin. Comparison between all test groups showed highly significant differences (P interactions between local endodontic medicaments, dentin, and pulp tissue. Copyright © 2013 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Antibacterial Efficacy of Calcium Hydroxide and Chlorhexidine Mixture for Treatment of Teeth with Primary Endodontic Lesions: A Randomized Clinical Trial.

Science.gov (United States)

Donyavi, Zakiyeh; Ghahari, Parastoo; Esmaeilzadeh, Mohammad; Kharazifard, Mohammadjavad; Yousefi-Mashouf, Rasoul

2016-01-01

This study compared the root canal microbial count of necrotic teeth after irrigation with 6% sodium hypochlorite (NaOCl) (single session treatment) and two-session root canal treatment with two-week application of calcium hydroxide (CH) mixed with 0.2% chlorhexidine (CHX) as intracanal medicament. In this randomized clinical trial, single-rooted necrotic teeth were divided into two groups. Root canal was irrigated with 2 mL of 6% NaOCl in one group, and a mixture of 0.2% CHX and CH powder as an intracanal medicament for two weeks, in the other group. Root canal samples were obtained before and after the intervention and number of colony forming units (CFUs) was counted in each phase. The reduction of Enterococcus faecalis CFU was not significantly different between the two groups ( P =0.233) but the CFU of aerobic and anaerobic bacteria was significantly lower in CH+CHX group ( P endodontic lesions in two sessions with intracanal medicaments to achieve predictable results.

Synthesis of beta alumina from aluminum hydroxide and oxyhydroxide precursors

CSIR Research Space (South Africa)

Van Zyl, A

1993-02-01

Full Text Available Two aluminium oxyhydroxides, boehmite and pseudoboehmite, and two aluminium hydroxides, bayerite and gibbsite, have been investigated as precursors for the synthesis of the solid electrolyte, beta alumina. Reaction pathways and products have been...

Nickel hydroxide electrode. 3: Thermogravimetric investigations of nickel (II) hydroxides

Science.gov (United States)

Dennstedt, W.; Loeser, W.

1982-01-01

Water contained in Ni hydroxide influences its electrochemical reactivity. The water content of alpha and beta Ni hydroxides is different with respect to the amount and bond strength. Thermogravimetric experiments show that the water of the beta Ni hydroxides exceeding the stoichiometric composition is completely removed at 160 deg. The water contained in the interlayers of the beta hydroxide, however, is removed only at higher temperatures, together with the water originating from the decomposition of the hydroxide. These differences are attributed to the formation of II bonds within the interlayers and between interlayers and adjacent main layers. An attempt is made to explain the relations between water content and the oxidizability of the Ni hydroxides.

Isomorfic Substitutions of Calcium by Strontium in Calcium Hydroxyapatite

International Nuclear Information System (INIS)

Christensen, Hilbert

1962-12-01

By means of homogeneous precipitation it has been possible to synthesize crystalline solid solutions of calcium strontium hydroxyapatite from aqueous solutions. The lattice constants for the solid solutions were measured in the range Ca 9 Sr(PO 4 ) 6 (OH) 2 - CaSr 9 (PO 4 ) 6 (OH) 2 . The investigations show that the discrimination of strontium against calcium is considerably smaller than reported elsewhere (1). Strontium is preferentially built into the c-axis direction of the apatite lattice

An in vitro study: Evaluation of intracanal calcium hydroxide removal with different file systems

Directory of Open Access Journals (Sweden)

Atul Jain

2017-01-01

Full Text Available Background: Calcium hydroxide (Ca(OH2 is the most commonly used intracanal material; it needs to be removed in entirety before obturation. Several techniques have been used for the same including use of various hand and rotary files. Aim: This study was carried out to compare the efficacy of Hand K files and single and multiple rotary file system in removal of Ca(OH2. Methodology: Distobuccal root of 45 maxillary molars were selected on the basis of specified inclusion and exclusion criteria. They were divided into three groups - Group 1 (H and K file, Group 2 (HERO Shaper, and Group 3 (One Shape. Biomechanical preparation (BMP was carried out as per the manufacturer's instructions; 2.5% sodium hypochlorite was used as the irrigant and 17% ethylenediaminetetraacetic acid as the penultimate irrigant. Ca(OH2powder was mixed with normal saline to obtain a paste; canals were filled with this paste using a Lentulo spiral and were sealed. After 7 days, Ca(OH2was removed, using the same file system as that used for BMP. Samples were sectioned longitudinally and evaluated under a stereomicroscope. Statistical Analysis: Statistical analysis of the obtained data was carried out using one-way analysis of variance test. Results: HERO Shaper displayed better removal of Ca(OH2than One Shape and Hand K file. Moreover, removal was better in the middle third of canal than apical third. Conclusion: Multiple rotary file system (HERO Shaper is more effective in removal of Ca(OH2than the single file system (One Shape

Calculated solubility isotherm of a system of alkaline earth sulfates and hydroxides in water

International Nuclear Information System (INIS)

MOshinskii, A.S.; TIkomirova, K.A.

1986-01-01

Tis paper examines the calculation of the isothermal solubility diagram of a system of alkaline earth sulfates and hydroxides in water which makes it possible to substantiate, to a considerable extent, the natural physicochemical mineralization of natural waters, in particular water from geochemical sources. The present paper investigates the solubility of the equilibrium solid phases of a system of alkaline earth sulfates and hydroxides in water. A projection is shown of the composition prism of the quinary reciprocal system with demarcation of the crystallization areas of each sulfate and hydroxide of the component subsystems. The computational formulas for calculating solubility were derived from the solubility product principle, with allowance for ion activity coefficients in saturated hydroxide solutions

Analysis of Zr++++ dan ZrO++ cations through their Hydroxide precipitate with thermal differential analysis method

International Nuclear Information System (INIS)

Simbolon, Sahat; Ratmi-Herlani

1996-01-01

Hydroxide of zirconyl and zirconium, made by reacting zirconium and zirconyl solution with NH 4 OH 25 % solution, were analysed by thermal differential analysis (TDA). It was also done TDA method for hydroxide of zirconyl and zirconium, made by reacting zirconyl chloride and zirconium chloride solid with NH 4 OH 25 % solution directly. It was found that TDA of hydroxide precipitate made through solution had a clear TDA counter, meanwhile TDA thermogram of hydroxide precipitate made by direct adding NH 4 OH 25 % solution to zirconyl and zirconium hydroxide had no clear TDA thermogram. Precipitate Zr O(OH) 2 and Zr(OH) 4 found through solution could be differentiated each other based on their TDA thermograms

Efficacy of XP-endo Finisher File in Removing Calcium Hydroxide from Simulated Internal Resorption Cavity.

Science.gov (United States)

Keskin, Cangül; Sariyilmaz, Evren; Sariyilmaz, Öznur

2017-01-01

The aim of this study was to evaluate the effect of supplementary use of XP-endo Finisher file, passive ultrasonic activation (PUI), EndoActivator (EA), and CanalBrush (CB) on the removal of calcium hydroxide (CH) paste from simulated internal resorption cavities. The root canals of 110 extracted single-rooted teeth with straight canals were prepared up to size 50. The specimens were split longitudinally, and standardized internal resorption cavities were prepared with burs. The cavities and root canals were filled with CH paste. The specimens were divided into 5 groups as follows: XP-endo Finisher, EA, PUI, CB, and syringe irrigation (SI). The root canals were irrigated with 5.25% NaOCl and 17% EDTA for 2 minutes, respectively. Apart from the SI group, both solutions were activated by using tested techniques for 1 minute. The quantity of CH remnants on resorption cavities was scored. Data were analyzed by using Kruskal-Wallis H and Mann-Whitney U tests. XP-endo Finisher and PUI removed significantly more CH than SI, EA, and CB (P  .05). Differences among SI, EA, and CB were also non-significant (P > .05). None of the tested techniques render the simulated internal resorption cavities free of CH debris. XP-endo Finisher and PUI were superior to SI, CB, and EA. Copyright © 2016 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

The thickness of odontoblast-like cell layer after induced by propolis extract and calcium hydroxide

Directory of Open Access Journals (Sweden)

Irfan Dwiandhono

2016-12-01

Full Text Available Background: Propolis is a substance made from resin collected by bees (Apis mellifera from variety of plants, mixed with its saliva and various enzymes to build a nest. Propolis has potential antimicrobial and antiinflammatory agents with some advantages over calcium hydroxide (Ca(OH2. Ca(OH2 has been considered as the “gold standard” of direct pulp-capping materials, but there are still some weakness of its application. First, it can induce pulp inflammation which last up to 3 months. Second, the tissue response to Ca(OH2 is not always predictable. Third, the tunnel defect can probably formed in dentinal bridge with possible bacterial invasion in that gap. Purpose: This study was aimed to determine and compare the thickness of odontoblast-like cells layer after induced by propolis extract and Ca(OH2 in rat’s pulp tissue. Method: Class 1 preparation was done in maxillary first molar tooth of wistar mice until the pulp opened. The Ca(OH2 and propolis extract was applied to induce the formation of odontoblast-like cells, the cavity was filled with RMGIC. The teeth were extracted (after 14 and 28 days of induction. The samples were then processed for histological evaluation. Result: There were significant differences between the thickness of odontoblast-like cells after induced by propolis extract and Ca(OH2. Conclusion: The propolis extract as the direct pulp capping agent produces thicker odontoblast-like cell layer compared to Ca(OH2.

Effect of the leaching of calcium hydroxide from cement paste on mechanical and physical properties

International Nuclear Information System (INIS)

Carde, C.; Francois, R.

1997-01-01

This paper deals with the effect of the leaching process of cement based materials on their mechanical and physical properties. In order to characterize this effect, the authors have performed experiments on cement paste samples. The leaching process was achieved by the use of a 50% concentrate solution of ammonium nitrate. Both compression tests and water porosity tests were conducted on micro-cylinder samples (10, 12, 14 and 20 mm of diameter) because of the slow kinetics of degradation due to the leaching. The deterioration of the cement paste and the mortar exposed to the action of the ammonium nitrate was manifested by a peripheral zone of less resistance. This process induces mainly a total leaching of Ca(OH) 2 and a progressive decalcification of C-S-H which leads to a gradient of C/S ratio in the leaching zone. Both mechanical tests and water porosity tests show that there is a linear variation of the loss of strength and the increase in porosity in relation to the ratio of degraded area over total area of the sample A d /A t . It means that both compressive resistance and water porosity of the leaching zone are constant whatever the size of the degraded zone and then whatever the time of exposure to the chemical attack. So the authors could venture the hypothesis that the dissolution of calcium hydroxide is the essential parameter governing both decrease in strength and increase in porosity

Effects of chopping, and soaking in water, hydrochloric acidic and calcium hydroxide solutions on the nutritional value of Acacia villosa for goats

Energy Technology Data Exchange (ETDEWEB)

Wina, E. [Research Institute for Animal Production, Bogor (Indonesia)]. E-mail: winabudi@yahoo.com; Tangendjaja, B.; Susana, I.W.R. [Research Institute for Animal Production, Bogor (Indonesia)

2005-08-19

Acacia villosa, a thornless shrub legume, has potential as a feed supplement for ruminants if anti-nutritional factors, especially tannins, can be overcome. The effects of chopping and soaking the leaves on the amounts of tannin in the extracting solution and that left in the recovered leaves were studied. The tannin and non-tannin phenolics were solubilized in the extracting solution and the amount was increased with the soaking time. Soaking in calcium hydroxide solution, hydrochloric acid or water removed 41-76% of tannin and total phenolics removed from the recovered leaves. Soaking of the leaves also removed fermentable materials and reduced the gas production. In the first of two digestibility experiments, three groups of goats received one of these diets, those were: (1) sugar cane tops: unsoaked Acacia leaves (7:3), (2) sugar cane tops: water soaked Acacia leaves (7:3) and (3) sugar cane tops: water soaked Acacia leaves (7:3) + 100 g/day of cassava flour. Live weight of goats was measured every 2 weeks and a large increase in average daily gain was obtained for goats fed diet containing water soaked leaves and cassava flour (71 g/day) compared to those fed diet containing unsoaked leaves and water soaked leaves (38.9 and 44.7 g/day, respectively) (P < 0.05). In the second digestibility experiment, the three diets were: (1) sugar cane tops: unsoaked Acacia (7:3), (2) sugar cane tops water soaked Acacia (7:3), (3) sugar cane tops: calcium hydroxide soaked Acacia (7:3). A supplement of 100 g/day of cassava flour was added to each of these three diets. In both digestibility experiments, soaking improved intake and digestibility of Acacia leaves, and cassava flour increased the intake, but when all the diets contained cassava flour, there was no significant difference (P > 0.05) found in intake or digestibility between unsoaked and soaked leaves. In conclusion, soaking reduced tannin in Acacia leaves, improved digestibility and intake of Acacia leaves. In the

Role of calcium-enriched mixture in endodontics

Directory of Open Access Journals (Sweden)

Pradeep Kabbinale

2015-01-01

Full Text Available Calcium-enriched mixture (CEM has been recently introduced as a hydrophilic tooth-colored cement. The CEM cement powder is composed of calcium oxide, calcium sulfate, phosphorus oxide, and silica as major elements. CEM is alkaline cement (pH~11 that releases calcium hydroxide (CH during and after setting. The physical properties of CEM, such as flow, film thickness, and primary setting time are favorable. This cement is biocompatible and induces formation of cementum, dentin, bone and periodontal tissues. This novel cement has an antibacterial effect comparable to CH and superior to mineral trioxide aggregate (MTA and sealing ability similar to MTA. Its clinical applications include pulp capping, pulpotomy, root-end filling and perforation repair. This review describes the composition, properties and clinical applications of CEM in endodontics.

A NEW PROCESS DEVELOPED FOR SEPARATION OF LIGNIN FROM AMMONIUM HYDROXIDE PRETREATMENT SOLUTIONS

Energy Technology Data Exchange (ETDEWEB)

Sherman, S.; Gorensek, M.; Milliken, C.

2010-12-14

A method is described for separating lignin from liquid solutions resulting from the pretreatment of lignocellulosic materials such as switchgrass with ammonium hydroxide. The method involves a sequence of steps including acidification, evaporation, and precipitation or centrifugation that are performed under defined conditions, and results in a relatively pure, solid lignin product. The method is tested on ammonium hydroxide solutions containing lignin extracted from switchgrass. Experimental results show that the method is capable of recovering between 66-95% of dissolved lignin as a precipitated solid. Cost estimates of pilot-scale and industrial-scale expressions of the process indicate that breakeven lignin prices of $2.36/kg and $0.78/kg, respectively, may be obtainable with this recovery method.

MgAl-Layered Double Hydroxide Solid Base Catalysts for Henry Reaction: A Green Protocol

Directory of Open Access Journals (Sweden)

Magda H. Abdellattif

2018-03-01

Full Text Available A series of MgAl-layered double hydroxide (MgAl-HT, the calcined form at 500 °C (MgAlOx, and the rehydrated one at 25 °C (MgAl-HT-RH were synthesized. Physicochemical properties of the catalysts were characterized by X-ray diffraction (XRD and scanning electron microscopy (SEM. Surface area of the as-synthesized, calcined, and rehydrated catalysts was determined by N2 physisorption at −196 °C. CO2 temperature-programmed desorption (CO2-TPD was applied to determine the basic sites of catalysts. The catalytic test reaction was carried out using benzaldehyde and their derivatives with nitromethane and their derivatives. The Henry products (1–15 were obtained in a very good yield using MgAl-HT-RH catalyst either by conventional method at 90 °C in liquid phase or under microwave irradiation method. The mesoporous structure and basic nature of the rehydrated solid catalyst were responsible for its superior catalytic efficiency. The robust nature was determined by using the same catalyst five times, where the product % yield was almost unchanged significantly.

Isomorfic Substitutions of Calcium by Strontium in Calcium Hydroxyapatite

Energy Technology Data Exchange (ETDEWEB)

Christensen, Hilbert

1962-12-15

By means of homogeneous precipitation it has been possible to synthesize crystalline solid solutions of calcium strontium hydroxyapatite from aqueous solutions. The lattice constants for the solid solutions were measured in the range Ca{sub 9}Sr(PO{sub 4}){sub 6}(OH){sub 2} - CaSr{sub 9}(PO{sub 4}){sub 6}(OH){sub 2}. The investigations show that the discrimination of strontium against calcium is considerably smaller than reported elsewhere (1). Strontium is preferentially built into the c-axis direction of the apatite lattice.

Determination of calcium and magnesium in nuclear grade alumina by ion chromatography technique

International Nuclear Information System (INIS)

Hespanhol, E.C.B.; Pires, M.A.F.; Atalla, L.T.

1987-07-01

A simple method for solubilization of alumina and separation of magnesium and calcium from alumina matrix was developed by initial coprecipitation of those elements with iron(III) hydroxide. Calcium and magnesium were later separated from iron chloride anionic complex in a Dowex 1-X 10 anionic exchange resin. The ion chromatography tecnnique was employed for the analysis of calcium and magnesium. One hundred percent recovery for calcium and magnesium was obtained in their separation from alumina. A precision of 6% and 10% for magnesium and calcium, respectively, was obtained in alumina samples analysis which contain less than 0,02% of magnesium and less than 0,08% of calcium. (Author) [pt

Characterization of Chlorhexidine-Loaded Calcium-Hydroxide Microparticles as a Potential Dental Pulp-Capping Material

Directory of Open Access Journals (Sweden)

Balasankar M. Priyadarshini

2017-06-01

Full Text Available This study explores the delivery of novel calcium hydroxide [Ca(OH2] microparticles loaded with chlorhexidine (CHX for potential dental therapeutic and preventive applications. Herein, we introduce a new approach for drug-delivery to deep dentin-surfaces in the form of drug-loaded microparticles. Unloaded Ca(OH2 [Ca(OH2/Blank] and CHX-loaded/Ca(OH2 microparticles were fabricated by aqueous chemical-precipitation technique. The synthesized-microparticles were characterized in vitro for determination of surface-morphology, crystalline-features and thermal-properties examined by energy-dispersive X-ray scanning and transmission electron-microscopy (EDX-SEM/TEM, Fourier-transform infrared-spectroscopy (FTIR, X-ray diffraction (XRD, thermogravimetric analysis (TGA and differential scanning-calorimetry (DSC. Time-related pH changes, initial antibacterial/biofilm-abilities and cytotoxicity of CHX-loaded/Ca(OH2 microparticles were evaluated. Microparticles were delivered to dentin-surfaces with subsequent SEM examination of treated dentin-substrates. The in vitro and ex vivo CHX-release profiles were characterized. Ca(OH2/Blank were hexagonal-shaped with highest z-average diameter whereas CHX-inclusion evidenced micro-metric spheres with distinguishable surface “rounded deposits” and a negative-shift in diameter. CHX:Ca(OH2/50 mg exhibited maximum encapsulation-efficiency with good antibacterial and cytocompatible properties. SEM examination revealed an intact layer of microparticles on exposed dentin-surfaces with retention of spherical shape and smooth texture. Microparticles loaded on dentin-surfaces showed prolonged release of CHX indicating substantial retention on dentin-substrates. This study validated the inherent-applicability of this novel drug-delivery approach to dentin-surfaces using micro-metric CHX-loaded/Ca(OH2 microparticles.

Generation of Hydrogen, Lignin and Sodium Hydroxide from Pulping Black Liquor by Electrolysis

Directory of Open Access Journals (Sweden)

Guangzai Nong

2015-12-01

Full Text Available Black liquor is generated in Kraft pulping of wood or non-wood raw material in pulp mills, and regarded as a renewable resource. The objective of this paper was to develop an effective means to remove the water pollutants by recovery of both lignin and sodium hydroxide from black liquor, based on electrolysis. The treatment of a 1000 mL of black liquor (122 g/L solid contents consumed 345.6 kJ of electric energy, and led to the generation of 30.7 g of sodium hydroxide, 0.82 g of hydrogen gas and 52.1 g of biomass solids. Therefore, the recovery ratios of elemental sodium and biomass solids are 80.4% and 76%, respectively. Treating black liquor by electrolysis is an environmentally friendly technology that can, in particular, be an alternative process in addressing the environmental issues of pulping waste liquor to the small-scale mills without black liquor recovery.

Genotoxicity test of propolis extract, mineral trioksida aggregat, and calcium hydroxide on fibroblast BHK-21 cell cultures

Directory of Open Access Journals (Sweden)

Ceples Dian Kartika W.P

2015-03-01

Full Text Available Background: Health industry has always used natural products as an alternative. Propolis, a natural antibiotic, is a resinous yellow brown or dark brown substance derived from honey bees (Apis mellifera. The main chemical compounds contained in propolis are flavonoids, phenolics and other various aromatic compounds. Flavonoids are well known plant compounds that have antibacterial, antifungal, antiviral, antioxidant and anti-inflammatory proprieties. Propolis is expected to be an alternative used for root canal treatment with lower toxicity compared to calcium hydroxide (Ca(OH2 . Over the last decade, a new material, mineral trioxide aggregate (MTA was developed, and has been used as the gold standard. All materials used in mouth should be biocompatible. The initial level of material biocompatibility evaluation involves toxicity and genotoxicity tests. Purpose: This research is aimed to conduct comparison test of genotoxicity effect of propolis extract, MTA and Ca(OH2 on fibroblast BHK-21 cell culture. Methods: This research was conducted with single-cell gel electrophoresis method. Results: The results indicate that propolis extract cannot cause DNA damage, while MTA can cause apoptosis and Ca(OH2 can cause neucrosis. Conclusion: It can be concluded that propolis extract has genotoxicity effect lower than MTA and Ca(OH2 , but MTA has lower effect on fibroblast BHK-21 cell culture.

Magnesium Hydroxide

Science.gov (United States)

Magnesium hydroxide is used on a short-term basis to treat constipation.This medication is sometimes prescribed ... Magnesium hydroxide come as a tablet and liquid to take by mouth. It usually is taken as ...

Aluminum Hydroxide

Science.gov (United States)

Aluminum hydroxide is used for the relief of heartburn, sour stomach, and peptic ulcer pain and to ... Aluminum hydroxide comes as a capsule, a tablet, and an oral liquid and suspension. The dose and ...

Magnesium hydroxide extracted from a magnesium-rich mineral for CO2 sequestration in a gas-solid system.

Science.gov (United States)

Lin, Pao-Chung; Huang, Cheng-Wei; Hsiao, Ching-Ta; Teng, Hsisheng

2008-04-15

Magnesium hydroxide extracted from magnesium-bearing minerals is considered a promising agent for binding CO2 as a carbonate mineral in a gas-solid reaction. An efficient extraction route consisting of hydrothermal treatment on serpentine in HCl followed by NaOH titration for Mg(OH)2 precipitation was demonstrated. The extracted Mg(OH)2 powder had a mean crystal domain size as small as 12 nm and an apparent surface area of 54 m2/g. Under one atmosphere of 10 vol% CO2/N2, carbonation of the serpentine-derived Mg(OH)2 to 26% of the stoichiometric limit was achieved at 325 degrees C in 2 h; while carbonation of a commercially available Mg(OH)2, with a mean crystal domain size of 33 nm and an apparent surface area of 3.5 m2/g, reached only 9% of the stoichiometric limit. The amount of CO2 fixation was found to be inversely proportional to the crystal domain size of the Mg(OH)2 specimens. The experimental data strongly suggested that only a monolayer of carbonates was formed on the crystal domain boundary in the gas-solid reaction, with little penetration of the carbonates into the crystal domain.

Solid state characterization of commercial crystalline and amorphous atorvastatin calcium samples.

Science.gov (United States)

Shete, Ganesh; Puri, Vibha; Kumar, Lokesh; Bansal, Arvind K

2010-06-01

Atorvastatin calcium (ATC), an anti-lipid BCS class II drug, is marketed in crystalline and amorphous solid forms. The objective of this study was to perform solid state characterization of commercial crystalline and amorphous ATC drug samples available in the Indian market. Six samples each of crystalline and amorphous ATC were characterized using X-ray powder diffractometry (XRPD), differential scanning calorimetry (DSC), thermogravimetric analysis, Karl Fisher titrimetry, microscopy (hot stage microscopy, scanning electron microscopy), contact angle, and intrinsic dissolution rate (IDR). All crystalline ATC samples were found to be stable form I, however one sample possessed polymorphic impurity, evidenced in XRPD and DSC analysis. Amongst the amorphous ATC samples, XRPD demonstrated five samples to be amorphous 'form 27', while, one matched amorphous 'form 23'. Thermal behavior of amorphous ATC samples was compared to amorphous ATC generated by melt quenching in DSC. ATC was found to be an excellent glass former with T(g)/T(m) of 0.95. Residual crystallinity was detected in two of the amorphous samples by complementary use of conventional and modulated DSC techniques. The wettability and IDR of all amorphous samples was found to be higher than the crystalline samples. In conclusion, commercial ATC samples exhibited diverse solid state behavior that can impact the performance and stability of the dosage forms.

Effect of cetyl trimethyl ammonium bromide concentration on structure, morphology and carbon dioxide adsorption capacity of calcium hydroxide based sorbents

International Nuclear Information System (INIS)

Hlaing, Nwe Ni; Vignesh, K.; Sreekantan, Srimala; Pung, Swee-Yong; Hinode, Hirofumi; Kurniawan, Winarto; Othman, Radzali; Thant, Aye Aye; Mohamed, Abdul Rahman; Salim, Chris

2016-01-01

Graphical abstract: Carbonation conversions of (a) CC, (b) CH-2, (c) CH-4, (d) CH-6, (e) CH-8 precursor adsorbents for 10 cycles. - Highlights: • Ca(OH)_2 precursor was synthesized using precipitation method. • The effect of CTAB concentration on the synthesis of Ca(OH)_2 was studied. • The sorbent synthesized using 0.8 M of CTAB showed good CO_2 adsorption capacity. • The cyclic stability of Ca(OH)_2 was increased with increase of CTAB concentration. - Abstract: Calcium hydroxide (Ca(OH)_2) has been proposed as an important material for industrial, architectural, and environmental applications. In this study, calcium acetate was used as a precursor and cetyl trimethyl ammonium bromide (CTAB) was used as a surfactant to synthesize Ca(OH)_2 based adsorbents for carbon dioxide (CO_2) capture. The effect of CTAB concentration (0.2–0.8 M) on the structure, morphology and CO_2 adsorption performance of Ca(OH)_2 was studied in detail. The synthesized samples were characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, field emission scanning electron microscopy (FESEM), BET surfaced area and thermogravimetry-differential thermal analysis (TG–DTA) techniques. The phase purity, crystallite size, Brunauer–Emmett–Teller (BET) surface area and CO_2 adsorption performance of Ca(OH)_2 precursor adsorbents were significantly increased when the concentration of CTAB was increased. XRD results showed that pure Ca(OH)_2 phase was obtained at the CTAB concentration of 0.8 M. TGA results exhibited that 0.8 M of CTAB-assisted Ca(OH)_2 precursor adsorbent possessed a residual carbonation conversion of ∼56% after 10 cycles.

Error causes in the determination of the acid-base reactivity of oxi-hydroxides

International Nuclear Information System (INIS)

Duc, M.; Lefevre, G.; Fedoroff, M.

2004-01-01

The long term safety of radioactive waste depositories is based on the sorption of radionuclides from underground water onto engineered and natural barriers. For a quantitative prediction of the migration in such barriers, we need accurate sorption data. Models should be in agreement with the sorption mechanism. Surface complexation is the most often used model for oxides and hydroxides. In fact, there are several types of surface complexation models such as 1-pK and 2-pK monosite, 1-pK and 2-pK multisite, pK-distribution models. Furthermore, there are several ways to describe the distribution of the electrostatic potential in the vicinity of the solid surface (CCM, DLM, BSM, TLM,..). However, all these models are based on the acid-base properties of superficial hydroxide or oxide groups of the solid. It is necessary to determine the surface charge versus pH (titration curves), the point of zero charge (pzc), the surface density of sites active towards protons and hydroxides in aqueous solutions, the acid-base constants of these sites. These parameters are then used for calculating the sorption constants of ions other than protons and hydroxide ions. It is therefore important to determine these parameters very accurately. A comparison of acid-base parameters published in the literature shows a large scatter for the ''same'' oxides [1,2]. Several causes could explain this scatter. One reason is the use of different models, each electrostatic models leading to different values of site density and constants. However, titration curves and pzc are independent of the model chosen. Another reason may be uncontrolled differences in the composition and purity of oxides. Finally, other causes could be found in the titration procedure, in the solubility and the stability of the solid. In order to understand more about the acid-base properties of oxides and about the origin of the discrepancies between measurements, we have performed a systematic experimental study of several

Role of oxidative stress, mitochondrial membrane potential, and calcium homeostasis in human lymphocyte death induced by nickel carbonate hydroxide in vitro

Energy Technology Data Exchange (ETDEWEB)

M' Bemba-Meka, Prosper [Faculty of Medicine, Universite de Montreal, QC (Canada); University of Louisville, Department of Pharmacology and Toxicology, Center for Genetics and Molecular Medicine, Louisville, KY (United States); Lemieux, Nicole [Universite de Montreal, Department of Pathology and Cellular Biology, Main Station, P.O. Box 6128, Montreal, QC (Canada); Chakrabarti, Saroj K. [Faculty of Medicine, Universite de Montreal, QC (Canada)

2006-07-15

When isolated human lymphocytes were treated in vitro with various concentrations of soluble form of nickel carbonate hydroxide (NiCH) (0-1 mM), at 37 C for 4 h, both concentration- and time-dependent effects of NiCH on lymphocyte death were observed. Increased generation of hydrogen peroxide (H{sub 2}O{sub 2}), superoxide anion (O{sub 2} {sup -}), depletion of both no protein (NP-) and protein (P-) sulfhydryl (SH) contents and lipid peroxidation (LPO) were induced by NiCH. Pretreatment of lymphocytes with either catalase (H{sub 2}O{sub 2} scavenger), or deferoxamine (DFO) (iron chelator), or excess glutathione (GSH) (an antioxidant) not only significantly reduced the NiCH-induced generation of H{sub 2}O{sub 2} and LPO, but also increased the NP-SH and P-SH contents initially reduced by NiCH. NiCH-induced generation of excess O{sub 2} {sup -} but not excess LPO was significantly reduced by pretreatment with superoxide dismutase (SOD). NiCH-induced lymphocyte death was significantly prevented by pre-treatment with either catalase, or dimethylthiourea/mannitol (hydroxyl radical scavengers), or DFO, or excess GSH/N-acetylcysteine. NiCH-induced lymphocyte death was also significantly prevented by pretreatment with excess SOD. Thus, various types of oxidative stresses play an important role in NiCH-induced lymphocyte death. Cotreatment with cyclosporin A, a specific inhibitor of alteration in mitochondrial membrane potential ({delta}{psi}{sub m}), not only inhibited NiCH-induced alteration in {delta}{psi}{sub m}, but also significantly prevented Ni-compound-induced lymphocyte death. Furthermore, NiCH-induced destabilization of cellular calcium homeostasis. As such, NiCH-induced lymphocyte death was significantly prevented by modulating intracellular calcium fluxes such as Ca{sup 2+} channel blockers and intracellular Ca{sup 2+} antagonist. Thus, the mechanism of NiCH (soluble form)-induced activation of lymphocyte death signalling pathways involves not only the excess

Interactions between iron(III)-hydroxide polymaltose complex and commonly used medications / laboratory studies in rats.

Science.gov (United States)

Funk, Felix; Canclini, Camillo; Geisser, Peter

2007-01-01

Simple iron salts, such as iron sulphate, often interact with food and other medications reducing bioavailability and tolerability. Iron(III)-hydroxide polymaltose complex (IPC, Maltofer) provides a soluble form of non-ionic iron, making it an ideal form of oral iron supplementation. The physicochemical properties of IPC predict a low potential for interactions. The effects of co-administration with aluminium hydroxide (CAS 21645-51-2), acetylsalicylic acid (CAS 50-78-2), bromazepam (CAS 1812-30-2), calcium acetate (CAS 62-54-4), calcium carbonate (CAS 471-34-1), auranofin (CAS 34031-32-8), magnesium-L-aspartate hydrochloride (CAS 28184-71-6), methyldopa sesquihydrate (CAS 41372-08-1), paracetamol (CAS 103-90-2), penicillamine (CAS 52-67-5), sulfasalazine (CAS 599-79-1), tetracycline hydrochloride (CAS 64-75-5), calcium phosphate (CAS 7757-93-9) in combination with vitamin D3 (CAS 67-97-0), and a multi-vitamin preparation were tested in rats fed an iron-deficient diet. Uptake of iron from radiolabelled IPC with and without concomitant medications was compared. None of the medicines tested had a significant effect on iron uptake. Iron-59 retrieval from blood and major storage organs was 64-76% for IPC alone compared with 59-85% following co-administration with other medications. It is concluded that, under normal clinical conditions, IPC does not interact with these medications.

Synthesis, characterization and stability of Cr(III) and Fe(III) hydroxides

Energy Technology Data Exchange (ETDEWEB)

Papassiopi, N.; Vaxevanidou, K.; Christou, C.; Karagianni, E.; Antipas, G.S.E., E-mail: gantipas@metal.ntua.gr

2014-01-15

Highlights: • Fe(III)–Cr(III) hydroxides enhance groundwater quality better than pure Cr(III) compounds. • Crystalline Cr(OH){sub 3}·3H{sub 2}O was unstable, with a solubility higher than 50 μg/l. • Amorphous Cr(OH){sub 3}(am) was stable with a solubility lower than 50 μg/l in the range 5.7 < pH < 11. • For mixed Fe{sub 0.75}Cr{sub 0.25}(OH){sub 3}, the stability region was extended to 4.8 < pH < 13.5. -- Abstract: Chromium is a common contaminant of soils and aquifers and constitutes a major environmental problem. In nature, chromium usually exists in the form of two oxidation states, trivalent, Cr(III), which is relatively innocuous for biota and for the aquatic environment, and hexavalent, Cr(VI) which is toxic, carcinogenic and very soluble. Accordingly, the majority of wastewater and groundwater treatment technologies, include a stage where Cr(VI) is reduced to Cr(III), in order to remove chromium from the aqueous phase and bind the element in the form of environmentally stable solid compounds. In the absence of iron the final product is typically of the form Cr(OH){sub 3}·xH{sub 2}O whereas in the presence of iron the precipitate is a mixed Fe{sub (1−x)}Cr{sub x}(OH){sub 3} phase. In this study, we report on the synthesis, characterisation and stability of mixed (Fe{sub x},Cr{sub 1−x})(OH){sub 3} hydroxides as compared to the stability of Cr(OH){sub 3}. We established that the plain Cr(III) hydroxide, abiding to the approximate molecular formula Cr(OH){sub 3}·3H{sub 2}O, was crystalline, highly soluble, i.e. unstable, with a tendency to transform into the stable amorphous hydroxide Cr(OH){sub 3}(am) phase. Mixed Fe{sub 0.75}Cr{sub 0.25}(OH){sub 3} hydroxides were found to be of the ferrihydrite structure, Fe(OH){sub 3}, and we correlated their solubility to that of a solid solution formed by plain ferrihydrite and the amorphous Cr(III) hydroxide. Both our experimental results and thermodynamic calculations indicated that mixed Fe

Effectiveness of different irrigation protocols on calcium hydroxide removal from simulated immature teeth after apexification

Directory of Open Access Journals (Sweden)

Evren Ok

2015-01-01

Full Text Available Aim: To evaluate the effectiveness of different irrigation solutions and ultrasonic activation of the irrigation solutions on the removal of calcium hydroxide (Ca(OH2 from the simulated immature root canals after apexification. Materials and methods: One-hundred and one single-rooted teeth were used. The root canals were shaped with ProTaper rotary files up to F5. Simulation of roots with immature apices was carried out using size 4 Unicore drills. An injectable Ca(OH2 was injected into each root canal, and packed to the working length. Then, cotton pellets were placed over canal orifices, and apical and coronal parts of the roots were sealed with resin-modified glass ionomer cement, and light cured. Specimens were stored in distilled water for 3 months at 37°C. After 3 months, the temporary coronal seal was removed and the samples were randomly divided into: (a saline (n = 20, (b ultrasonic activation of saline (n = 20, (c sodium hypochlorite (NaOCl (n = 20, (d ultrasonic activation of NaOCl (n = 15, (e chlorhexidine digluconate (CHX (n = 20 and one positive control group (n = 3 and one negative control group (n = 3. The amount of remaining Ca(OH2 on the canal walls was measured under stereomicroscope with 30× magnification. Comparisons between groups were made by the non-parametric Kruskal-Wallis test and Dunn post-test at a significance level of p  0.05 groups. Conclusions: Irrigation solutions and ultrasonic activation of the irrigation solutions could not completely remove Ca(OH2 from the simulated immature root canals.

Influence of porosity and relative humidity on consolidation of dolostone with calcium hydroxide nanoparticles: Effectiveness assessment with non-destructive techniques

International Nuclear Information System (INIS)

Lopez-Arce, P.; Gomez-Villalba, L.S.; Pinho, L.; Fernandez-Valle, M.E.; Alvarez de Buergo, M.; Fort, R.

2010-01-01

Slaked lime (Ca(OH) 2 ) nanoparticles were exposed at 33% and 75% relative humidity (RH) to consolidate dolostone samples used in historical buildings. Non-destructive techniques (NDT) were applied to determine the chemical, morphological, physical and hydric properties of the stone samples, before and after 20 days treatment. Morphological and mineralogical characterisation of the nanoparticles was performed. 75% RH favors the consolidation process studied under Environmental Scanning Electron Microscopy (ESEM-EDS), spectrophotometry, capillarity, water absorption under vacuum, ultrasound velocity, Nuclear Magnetic Resonance (imaging and relaxometry) and Optical Surface Roughness analyses. At 75% RH the nanoparticles fill the pores and inter-crystalline dolomite grain contacts but do not favor calcite re-crystallization as it occurs at 33% RH. The ESEM, XRD and TEM analyses under 75% RH reveal the fast transformation of portlandite (Ca(OH) 2 ) into vaterite (CaCO 3 ), monohydrocalcite (CaCO 3 . H 2 O) and calcite (CaCO 3 ), and eventually the physical and hydric properties of the stones significantly improve. New insights are provided for the assessment of consolidation effectiveness of porous carbonate stones with calcium hydroxide nanoparticles under optimum RH conditions combining several NDT.

Influence of porosity and relative humidity on consolidation of dolostone with calcium hydroxide nanoparticles: Effectiveness assessment with non-destructive techniques

Energy Technology Data Exchange (ETDEWEB)

Lopez-Arce, P., E-mail: plopezar@geo.ucm.es [Group of Applied Petrology to Heritage Conservation, Institute of Economic Geology (CSIC-UCM), Madrid 28040 (Spain); Gomez-Villalba, L.S. [Group of Applied Petrology to Heritage Conservation, Institute of Economic Geology (CSIC-UCM), Madrid 28040 (Spain); Pinho, L. [Center of Construction Studies, Engineering Faculty, Oporto University, Oporto 4200-465 (Portugal); Fernandez-Valle, M.E. [Research Assistance Center, Nuclear Magnetic Resonance (Pluridisciplinar Institute), Complutense University of Madrid (UCM), Madrid 28040 (Spain); Alvarez de Buergo, M.; Fort, R. [Group of Applied Petrology to Heritage Conservation, Institute of Economic Geology (CSIC-UCM), Madrid 28040 (Spain)

2010-02-15

Slaked lime (Ca(OH){sub 2}) nanoparticles were exposed at 33% and 75% relative humidity (RH) to consolidate dolostone samples used in historical buildings. Non-destructive techniques (NDT) were applied to determine the chemical, morphological, physical and hydric properties of the stone samples, before and after 20 days treatment. Morphological and mineralogical characterisation of the nanoparticles was performed. 75% RH favors the consolidation process studied under Environmental Scanning Electron Microscopy (ESEM-EDS), spectrophotometry, capillarity, water absorption under vacuum, ultrasound velocity, Nuclear Magnetic Resonance (imaging and relaxometry) and Optical Surface Roughness analyses. At 75% RH the nanoparticles fill the pores and inter-crystalline dolomite grain contacts but do not favor calcite re-crystallization as it occurs at 33% RH. The ESEM, XRD and TEM analyses under 75% RH reveal the fast transformation of portlandite (Ca(OH){sub 2}) into vaterite (CaCO{sub 3}), monohydrocalcite (CaCO{sub 3} . H{sub 2}O) and calcite (CaCO{sub 3}), and eventually the physical and hydric properties of the stones significantly improve. New insights are provided for the assessment of consolidation effectiveness of porous carbonate stones with calcium hydroxide nanoparticles under optimum RH conditions combining several NDT.

The effects of different irrigation protocols on removing calcium ...

African Journals Online (AJOL)

2015-11-02

Nov 2, 2015 ... acid (PAA) is suitable for final irrigation of root canals.[10] PAA ... others to remix, tweak, and build upon the work non-commercially, as long as the author is ..... particles could not find a reservoir opening such as an opened .... calcium hydroxide/chlorhexidine medicaments from the root canal. Int Endod.

Clinical and radiographic evaluation of indirect pulp treatment with MTA and calcium hydroxide in primary teeth (in-vivo study

Directory of Open Access Journals (Sweden)

Vimi George

2015-01-01

Full Text Available Objectives: Clinical and radiographic effects of mineral trioxide aggregate (white MTA and calcium hydroxide (Dycal in indirect pulp treatment (IPT of primary teeth over a period of 6 months. Materials and Methods: A clinical trial with sample size of 40 primary molars between the age group of 5-9 years, of which, 20 teeth were considered, each for MTA and Dycal. Measurements on the digitized radiographs were performed at baseline, third and sixth month, increase in dentin was then measured using Corel Draw software. Result: Independent t-test had indicated that at the end of 3 months and 6 months, a statistically significant increase in dentin thickness with both MTA and Dycal (P-value ≤ 0.001 was found. Within the MTA group, the thickness of dentin formed was 0.089 mm ± 0.031 mm at first 3 months and 0.055 ± 0.022 mm at the second 3 months, (P ≤ 0.001 evaluated using paired t-test. In the Dycal group, increment in dentin deposited was 0.068 mm at the first 3 months and second 3 months, it was 0.030 mm (P-value ≤ 0.001. Conclusion: Clinically and radiographically, MTA is superior to Dycal as a good IPT medicament in primary teeth.

Clinical and radiographic evaluation of indirect pulp treatment with MTA and calcium hydroxide in primary teeth (in-vivo study).

Science.gov (United States)

George, Vimi; Janardhanan, Suresh Kumar; Varma, Balagopal; Kumaran, Parvathy; Xavier, Arun Mamachan

2015-01-01

Clinical and radiographic effects of mineral trioxide aggregate (white MTA) and calcium hydroxide (Dycal) in indirect pulp treatment (IPT) of primary teeth over a period of 6 months. A clinical trial with sample size of 40 primary molars between the age group of 5-9 years, of which, 20 teeth were considered, each for MTA and Dycal. Measurements on the digitized radiographs were performed at baseline, third and sixth month, increase in dentin was then measured using Corel Draw software. Independent t-test had indicated that at the end of 3 months and 6 months, a statistically significant increase in dentin thickness with both MTA and Dycal (P-value ≤ 0.001) was found. Within the MTA group, the thickness of dentin formed was 0.089 mm ± 0.031 mm at first 3 months and 0.055 ± 0.022 mm at the second 3 months, (P ≤ 0.001) evaluated using paired t-test. In the Dycal group, increment in dentin deposited was 0.068 mm at the first 3 months and second 3 months, it was 0.030 mm (P-value ≤ 0.001). Clinically and radiographically, MTA is superior to Dycal as a good IPT medicament in primary teeth.

Synthesis, characterization and stability of Cr(III) and Fe(III) hydroxides

International Nuclear Information System (INIS)

Papassiopi, N.; Vaxevanidou, K.; Christou, C.; Karagianni, E.; Antipas, G.S.E.

2014-01-01

Highlights: • Fe(III)–Cr(III) hydroxides enhance groundwater quality better than pure Cr(III) compounds. • Crystalline Cr(OH) 3 ·3H 2 O was unstable, with a solubility higher than 50 μg/l. • Amorphous Cr(OH) 3 (am) was stable with a solubility lower than 50 μg/l in the range 5.7 0.75 Cr 0.25 (OH) 3 , the stability region was extended to 4.8 3 ·xH 2 O whereas in the presence of iron the precipitate is a mixed Fe (1−x) Cr x (OH) 3 phase. In this study, we report on the synthesis, characterisation and stability of mixed (Fe x ,Cr 1−x )(OH) 3 hydroxides as compared to the stability of Cr(OH) 3 . We established that the plain Cr(III) hydroxide, abiding to the approximate molecular formula Cr(OH) 3 ·3H 2 O, was crystalline, highly soluble, i.e. unstable, with a tendency to transform into the stable amorphous hydroxide Cr(OH) 3 (am) phase. Mixed Fe 0.75 Cr 0.25 (OH) 3 hydroxides were found to be of the ferrihydrite structure, Fe(OH) 3 , and we correlated their solubility to that of a solid solution formed by plain ferrihydrite and the amorphous Cr(III) hydroxide. Both our experimental results and thermodynamic calculations indicated that mixed Fe(III)–Cr(III) hydroxides are more effective enhancers of groundwater quality, in comparison to the plain amorphous or crystalline Cr(III) hydroxides, the latter found to have a solubility typically higher than 50 μg/l (maximum EU permitted Cr level in drinking water), while the amorphous Cr(OH) 3 (am) phase was within the drinking water threshold in the range 5.7 0.75 Cr 0.25 (OH) 3 hydroxides studied were of extended stability in the 4.8 < pH < 13.5 range

Push-out Bond Strength of Calcium Enriched Mixture Exposed to Alkaline Environment

Directory of Open Access Journals (Sweden)

Sobhnamayan F

2015-09-01

Full Text Available Statement of Problem: Calcium hydroxide which is commonly used as an intracanal medicament, changes the pH of dentin and periradicular tissues to an alkaline pH. In some clinical situations, endodontic reparative cements like calcium enriched mixture cement are used after calcium hydroxide therapy. However, the alkaline pH may affect the physical properties of this cement. Objectives: This study was designed to evaluate the effect of alkaline pH on the push-out bond strength of calcium enriched mixture. Materials and Methods: 80 root slices were prepared from single-rooted human teeth and their lumens were instrumented to achieve a diameter of 1.3mm. Calcium enriched mixture (CEM was mixed according to the manufacturer’s instruction and introduced into the lumens of root slices. The specimens were then randomly divided into 4 groups (n = 20 and wrapped in pieces of gauze soaked in synthetic tissue fluid (STF buffered in potassium hydroxide at pH values of 7.4, 8.4, 9.4, or 10.4. The samples were incubated for 4 days at 37°C. The push-out bond strengths were then measured using a universal testing machine. Failure modes were examined under a light microscope at ×20 magnification. The data were analyzed using one-way analysis of variance and Tukey’s post hoc tests. Results: The greatest (1.41 ± 0.193 MPa and lowest (0.8 ± 0.06 MPa mean push-out bond strengths were observed after exposure to pH values of 7.4 and 8.4, respectively. There were significant differences between the neutral group and the groups with pH of 8.4 (p = 0.008 and 10.4 (p = 0.022. The bond failure was predominantly of cohesive type for all experimental groups. Conclusions: Under the condition of this study, alkaline pH adversely affected the Push-out bond strength of CEM cement.

The effects of different irrigation protocols on removing calcium ...

African Journals Online (AJOL)

Objective: The aim of this study was to evaluate the efficiencies of different irrigation protocols and solutions in the removal of calcium hydroxide (Ca[OH]2). Materials and Methods: Sixty-eight maxillary incisors were used. Root canals were prepared and filled with Ca(OH)2. Two control (n = 4) and six experimental groups (n ...

A solid state NMR study of layered double hydroxides intercalated with para-amino salicylate, a tuberculosis drug

DEFF Research Database (Denmark)

Jensen, Nicholai Daugaard; Bjerring, Morten; Nielsen, Ulla Gro

2016-01-01

Para-amino salicylate (PAS), a tubercolosis drug, was intercalated in three different layered double hydroxides (MgAl, ZnAl, and CaAl-LDH) and the samples were studied by multi-nuclear (1H, 13C, and 27Al) solid state NMR (SSNMR) spectroscopy in combination with powder X-ray diffraction (PXRD....... Moreover, 13C MAS NMR and infra-red spectroscopy show that PAS did not decompose during synthesis. Large amounts (20-41%) of amorphous aluminum impurities were detected in the structure using 27Al single pulse and 3QMAS NMR spectra, which in combination with 1H single and double quantum experiments also...... showed that the M(II):Al ratio was higher than predicted from the bulk metal composition of MgAl-PAS and ZnAl-PAS. Moreover, the first high-resolution 1H SSNMR spectra of a CaAl LDH is reported and assigned using 1H single and double quantum experiments in combination with 27Al{1H} HETCOR....

Effect of cetyl trimethyl ammonium bromide concentration on structure, morphology and carbon dioxide adsorption capacity of calcium hydroxide based sorbents

Energy Technology Data Exchange (ETDEWEB)

Hlaing, Nwe Ni, E-mail: nwenihlaing76@gmail.com [School of Materials and Mineral Resources Engineering, Engineering Campus, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia); Department of International Development Engineering, Tokyo Institute of Technology, 2-12-1 Ookayama, Meguro-ku, Tokyo (Japan); Department of Physics, University of Yangon, 11041 Kamayut, Yangon (Myanmar); Vignesh, K., E-mail: vignesh134@gmail.com [School of Materials and Mineral Resources Engineering, Engineering Campus, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia); Anano Sphere Sdn Bhd, Lorong Industri 11, Kawasan Industri Bukit Panchor, 14300 Nibong Tebal, Penang (Malaysia); Sreekantan, Srimala, E-mail: srimala@usm.my [School of Materials and Mineral Resources Engineering, Engineering Campus, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia); Pung, Swee-Yong [School of Materials and Mineral Resources Engineering, Engineering Campus, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia); Hinode, Hirofumi; Kurniawan, Winarto [Department of International Development Engineering, Tokyo Institute of Technology, 2-12-1 Ookayama, Meguro-ku, Tokyo (Japan); Othman, Radzali [Faculty of Manufacturing Engineering, Universiti Teknikal Malaysia Melaka, Hang Tuah Jaya, 76100 Durian Tunggal, Malacca (Malaysia); Thant, Aye Aye [Department of Physics, University of Yangon, 11041 Kamayut, Yangon (Myanmar); Mohamed, Abdul Rahman [Low Carbon Economy (LCE) Research Group, School of Chemical Engineering, Engineering Campus, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia); Salim, Chris [Department of Environmental Engineering, Surya University, Tangerang 15810, Banten (Indonesia)

2016-02-15

Graphical abstract: Carbonation conversions of (a) CC, (b) CH-2, (c) CH-4, (d) CH-6, (e) CH-8 precursor adsorbents for 10 cycles. - Highlights: • Ca(OH){sub 2} precursor was synthesized using precipitation method. • The effect of CTAB concentration on the synthesis of Ca(OH){sub 2} was studied. • The sorbent synthesized using 0.8 M of CTAB showed good CO{sub 2} adsorption capacity. • The cyclic stability of Ca(OH){sub 2} was increased with increase of CTAB concentration. - Abstract: Calcium hydroxide (Ca(OH){sub 2}) has been proposed as an important material for industrial, architectural, and environmental applications. In this study, calcium acetate was used as a precursor and cetyl trimethyl ammonium bromide (CTAB) was used as a surfactant to synthesize Ca(OH){sub 2} based adsorbents for carbon dioxide (CO{sub 2}) capture. The effect of CTAB concentration (0.2–0.8 M) on the structure, morphology and CO{sub 2} adsorption performance of Ca(OH){sub 2} was studied in detail. The synthesized samples were characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, field emission scanning electron microscopy (FESEM), BET surfaced area and thermogravimetry-differential thermal analysis (TG–DTA) techniques. The phase purity, crystallite size, Brunauer–Emmett–Teller (BET) surface area and CO{sub 2} adsorption performance of Ca(OH){sub 2} precursor adsorbents were significantly increased when the concentration of CTAB was increased. XRD results showed that pure Ca(OH){sub 2} phase was obtained at the CTAB concentration of 0.8 M. TGA results exhibited that 0.8 M of CTAB-assisted Ca(OH){sub 2} precursor adsorbent possessed a residual carbonation conversion of ∼56% after 10 cycles.

Effect of rotary or manual instrumentation, with or without a calcium hydroxide/1% chlorhexidine intracanal dressing, on the healing of experimentally induced chronic periapical lesions.

Science.gov (United States)

De Rossi, Andiara; Silva, Léa A B; Leonardo, Mario R; Rocha, Lenaldo B; Rossi, Marcos A

2005-05-01

To evaluate the healing of experimentally induced chronic periapical lesions in dogs at 30, 75, and 120 days after root canal instrumentation with rotary NiTi files or manual K-files, with or without a calcium hydroxide/1% chlorhexidine paste intracanal dressing. The second, third, and fourth mandibular premolars and the second and third maxillary premolars of 5 dogs (12 to 18 months of age, weighing 8 to 15 kg) were selected for treatment (a total of 82 root canals). After pulp removal, the root canals were left exposed to the oral cavity for 7 days to allow microbial contamination, after which the root canals were sealed with ZOE cement until periapical lesions were confirmed with radiography. Group I and II teeth were instrumented with manual K-files using the crown-down technique. In group III and IV teeth, NiTi rotary files were used. The apical delta was perforated by using #20 to #30 K-files at the length of the tooth, thus creating a standardized apical opening. The apical stop was enlarged to size 70, with 2.5% sodium hypochlorite irrigation at each file change. Teeth in groups II and IV were dressed with calcium hydroxide (Ca(OH) 2 )/1% chlorhexidine (CHX) paste for 15 days before root filling. Group I and III teeth did not receive an intracanal dressing. The access openings of the teeth were permanently restored with silver amalgam condensed on a glass ionomer cement base. Pairs of standardized periapical radiographs were taken at the beginning of the treatment (0 days) and at 30, 75, and 120 days after filling. There was no significant difference in the rate of radiographic healing of the periapical lesions between manual and rotary instrumentation. Radiographs taken at 120 days showed that the treatment with Ca(OH) 2 /1% CHX paste resulted in a significant reduction in mean size of the periapical lesions in comparison to single-session treatment. These findings were also true for histologic observations. The findings support the hypothesis that

Use of Incineration Solid Waste Bottom Ash as Cement Mixture in Cement Production

Science.gov (United States)

Jun, N. H.; Abdullah, M. M. A. B.; Jin, T. S.; Kadir, A. A.; Tugui, C. A.; Sandu, A. V.

2017-06-01

Incineration solid waste bottom ash was use to examine the suitability as a substitution in cement production. This study enveloped an innovative technology option for designing new equivalent cement that contains incineration solid waste bottom ash. The compressive strength of the samples was determined at 7, 14, 28 and 90 days. The result was compared to control cement with cement mixture containing incineration waste bottom ash where the result proved that bottom ash cement mixture able achieve its equivalent performance compared to control cement which meeting the requirement of the standards according to EN 196-1. The pozzolanic activity index of bottom ash cement mixture reached 0.92 at 28 days and 0.95 at 90 and this values can be concluded as a pozzolanic material with positive pozzolanic activity. Calcium hydroxide in Portland cement decreasing with the increasing replacement of bottom ash where the reaction occur between Ca(OH)2 and active SiO2.

Utilization of Magnesium Hydroxide Produced by Magnesia Hydration as Fire Retardant for Nylon 6-6,6

Directory of Open Access Journals (Sweden)

Rocha Sônia D.F.

2001-01-01

Full Text Available The present work investigates the use of magnesium hydroxide, produced by magnesia hydration, as a fire retardant in polymers. The hydration was carried out in an autoclave, at temperature of 130°C for 1 hour, and the product was further submitted to cominution in a jet mill. The solids were characterized with regard to their chemical composition, particle size distribution, surface area and morphology. The performance evaluation of the hydroxide as a flame retardant for a copolymer of nylon 6-6,6 was carried out according to the UL94 specifications for vertical burning tests. V-0 flammability rating at 1.6 mm (60% magnesium hydroxide-filled nylon composite and at 3.2 mm (40% magnesium hydroxide filled nylon composite were achieved. Mechanical properties were maintained at the desired values. These results indicate that the hydroxide obtained from magnesia hydration can be successfully employed as a fire retardant for nylon 6-6,6.

Comparison of calcium carbonate and aluminium hydroxide as phosphate binders on biochemical bone markers, PTH(1-84), and bone mineral content in dialysis patients

DEFF Research Database (Denmark)

Jespersen, B; Jensen, J D; Nielsen, H K

1991-01-01

Bone mineral content, estimated by single-photon absorptiometry of the forearm, serum values of intact parathyroid hormone (PTH(1-84], osteocalcin, alkaline phosphatase, 1,25-dihydroxycholecalciferol (1,25(OH)2D3), and aluminium were determined during treatment with calcium carbonate (CaCO3......) or aluminium hydroxide (Al(OH)3) in 11 dialysis patients participating in a randomised cross-over study. Each treatment period lasted 6 months. Serum phosphorus was maintained in the range 1.5-2.0 mmol/l. During Al(OH)3 treatment bone mineral content (BMC) decreased by 11% per half-year (mean), but only by 3...... 0.05), osteocalcin decreased (89% versus 117%, P less than 0.01), alkaline phosphatase decreased (92% versus 116%, P less than 0.05), and aluminium decreased (56% versus 189%, P less than 0.05). 1,25(OH)2D3 remained unchanged in both periods. No increase in soft-tissue calcification was demonstrated...

Sodium hydroxide poisoning

Science.gov (United States)

Sodium hydroxide is a very strong chemical. It is also known as lye and caustic soda. This ... poisoning from touching, breathing in (inhaling), or swallowing sodium hydroxide. This article is for information only. Do ...

Holey nickel hydroxide nanosheets for wearable solid-state fiber-supercapacitors.

Science.gov (United States)

Shi, Peipei; Chen, Rong; Li, Li; An, Jianing; Hua, Li; Zhou, Jinyuan; Liu, Bin; Chen, Peng; Huang, Wei; Sun, Gengzhi

2018-03-28

Holey nickel hydroxide (Ni(OH) 2 ) nanosheets with a mean thickness of 2 nm are facilely synthesized, and then embedded in carbon nanotube (CNT) scaffolds to construct a hybrid fiber electrode, which shows a high volumetric capacitance of 335.9 F cm -3 at 0.8 A cm -3 and superior rate performance. The hybrid supercapacitor made from the Ni(OH) 2 /CNT fiber can deliver a high specific capacitance of 24.8 F cm -3 and an energy density of 5.8 mW h cm -3 with outstanding mechanical stability under repeated bending conditions.

Investigation into the role of NaOH and calcium ions in the synthesis of calcium phosphate nanoshells

Directory of Open Access Journals (Sweden)

C. H. Yeo

2012-03-01

Full Text Available Calcium phosphate (CaP nanoshells were prepared using negatively charged liposomes (1,2-dioleoyl-sn-glycero-3-phosphate sodium salt (DOPA as a template by base titration synthesis at various concentrations of NaOH and calcium ions. The elemental composition, morphology, particle size, particle size distribution and zeta potential of the products were determined via various characterisation techniques, such as energy-dispersive X-ray spectrometry (EDX, transmission electron microscopy (TEM, dynamic light scattering (DLS, laser Doppler velocimetry (LDV and Fourier transform infrared spectroscopy (FTIR. The best results showed that stable spherical CaP nanoshells with a mean particle size of 197.5 ± 5.8 nm and a zeta potential of -34.5 ± 0.6 mV were successfully formed when 0.100 M sodium hydroxide (NaOH and 0.100 M calcium ions were used. Moreover, an optimal pH of 10.52 and a final Ca/P molar ratio of 0.97 were achieved under these conditions.

Grout formulation for disposal of low-level and hazardous waste streams containing fluoride

Science.gov (United States)

McDaniel, E.W.; Sams, T.L.; Tallent, O.K.

1987-06-02

A composition and related process for disposal of hazardous waste streams containing fluoride in cement-based materials is disclosed. the presence of fluoride in cement-based materials is disclosed. The presence of fluoride in waste materials acts as a set retarder and as a result, prevents cement-based grouts from setting. This problem is overcome by the present invention wherein calcium hydroxide is incorporated into the dry-solid portion of the grout mix. The calcium hydroxide renders the fluoride insoluble, allowing the grout to set up and immobilize all hazardous constituents of concern. 4 tabs.

Direct Pulp Capping with Calcium Hydroxide, Mineral Trioxide Aggregate, and Biodentine in Permanent Young Teeth with Caries: A Randomized Clinical Trial.

Science.gov (United States)

Brizuela, Claudia; Ormeño, Andrea; Cabrera, Carolina; Cabezas, Roxana; Silva, Carolina Inostroza; Ramírez, Valeria; Mercade, Montse

2017-11-01

Direct pulp capping treatment is intended to preserve pulp vitality, to avoid or retard root canal treatment, and, in cases with an open apex, to allow continued root development. Historically, calcium hydroxide (CH) was the gold standard material, but nowadays calcium silicate materials (CSMs) are displacing CH because of their high bioactivity, biocompatibility, sealing ability, and mechanical properties. However, more randomized clinical trials are needed to confirm the appropriateness of CSMs as replacement materials for CH in direct pulp capping procedures. A randomized clinical trial was conducted that included 169 patients (mean age, 11.3 years) from the Maipo district (Chile). The inclusion criterion was patients with 1 carious permanent tooth with pulpal exposure, a candidate for a direct pulp capping procedure. The patients were randomly allocated to one of the experimental groups (CH, Biodentine, or mineral trioxide aggregate [MTA]). Clinical follow-up examinations were performed at 1 week, 3 months, 6 months, and 1 year. The Fisher exact test was performed. At the follow-up examination at 1 week, the patients showed 100% clinical success. At 3 months, there was 1 failure in the CH group. At 6 months, there were 4 new failures (1 in the CH group and 3 in the MTA group). At 1 year, there was another failure in the CH group. There were no statistically significant differences among the experimental groups. CSMs appear to be suitable materials to replace CH. Although no significant differences were found among the materials studied, Biodentine and MTA offered some advantages over CH. Copyright © 2017 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Effect of substrate nature on the electrochemical deposition of calcium-deficient hydroxyapatites

Science.gov (United States)

Gualdrón-Reyes, A. F.; Domínguez-Vélez, V.; Morales-Morales, J. A.; Cabanzo, R.; Meléndez, A. M.

2017-01-01

Calcium phosphates were obtained by reducing nitrate ions to produce hydroxide ions on TiO2/stainless steel and TiO2/titanium electrodes. TiO2 coatings on metallic substrates were prepared by sol-gel dip-coating method. The morphology of deposits was observed by FESEM. Chemical nature of calcium phosphate deposits was identified by Raman micro-spectroscopy and FESEM/EDS microanalysis. Electrochemical behavior of nitrate and nitrite reduction on stainless steel and titanium electrodes was studied by linear sweep voltammetry. In addition, voltammetric study of the calcium phosphate electrodeposition on both electrodes was performed. From these measurements was selected the potential to form a calcium phosphate. A catalytic current associated to nitrate reduction reaction was obtained for stainless steel electrode, leading to significant deposition of calcium phosphate. Ca/P ratio for both substrates was less than 1.67. The formation of calcium deficient hydroxyapatite was confirmed by Raman spectroscopy.

Contribution to the study of sorption mechanisms at solid-liquid interfaces: application to the cases of apatites and oxy-hydroxides

International Nuclear Information System (INIS)

Duc, M.

2002-11-01

Sorption-desorption phenomena play an important role in the transport of toxic and radioactive elements in surface and underground water in contact with solid matter. Selenium, which is one of the long-lived radionuclides present in radioactive waste, is characterized by several oxidation states and by anionic species in aqueous solutions. In order to predict its transport, we need a good knowledge of its sorption processes. We have studied the sorption of Se(IV) and Se(VI) on two types of solids present in natural media or which have been proposed as additives to active barriers: hydroxy-apatites, fluoro-apatite and iron oxi-hydroxides (goethite and hematite). Sorption mechanisms have been studied through an approach including several different and complementary methods: titrimetry, zeta-metry, scanning and transmission electron microscopy, infrared spectroscopy, X-ray diffraction, X-ray photo electron spectroscopy, etc... Results showed that Se(VI) is much less sorbed than Se(VI) on both types of solids. For Se(IV) the sorption mechanisms are different for iron oxides and apatites. On oxides, sorption increases when pH decreases. It can be interpreted by a surface complexation model, essentially through an inner sphere complex (monodentate or bidentate). Modelling of Se sorption curves was performed after the determination of acido-basic properties of oxides. However, the determination of the intrinsic properties of oxides is disturbed by several parameters identified as impurities, evolution of the solid in solution, kinetic and solubility of the solid. For apatites, selenium sorption proceeds by exchange with superficial groups, with a maximum of fixation at approximately pH 8. Thanks to XPS measurements and the elaboration of a mathematical model, we could determine the depth of penetration of both selenium and cadmium on apatites. (author)

The effects of potassium and rubidium hydroxide on the alkali-silica reaction

International Nuclear Information System (INIS)

Shomglin, K.; Turanli, L.; Wenk, H.-R.; Monteiro, P.J.M.; Sposito, G.

2003-01-01

Expansion of mortar specimens prepared with an aggregate of mylonite from the Santa Rosa mylonite zone in southern California was studied to investigate the effect of different alkali ions on the alkali-silica reaction in concrete. The expansion tests indicate that mortar has a greater expansion when subjected to a sodium hydroxide bath than in a sodium-potassium-rubidium hydroxide bath. Electron probe microanalysis (EPMA) of mortar bars at early ages show that rubidium ions, used as tracer, were present throughout the sample by the third day of exposure. The analysis also shows a high concentration of rubidium in silica gel from mortar bars exposed to bath solutions containing rubidium. The results suggest that expansion of mortar bars using ASTM C 1260 does not depend on the diffusion of alkali ions. The results indicate that the expansion of alkali-silica gel depends on the type of alkali ions present. Alkali-silica gel containing rubidium shows a lower concentration of calcium, suggesting competition for the same sites

Production of edible carbohydrates from formaldehyde in a spacecraft. pH variations in the calcium hydroxide catalyzed formose reaction. Final Report, 1 Jul. 1973 - 30 Jun. 1974. M.S. Thesis

Science.gov (United States)

Weiss, A. H.; Kohler, J. T.; John, T.

1974-01-01

The study of the calcium hydroxide catalyzed condensation of formaldehyde was extended to a batch reactor system. Decreases in pH were observed, often in the acid regime, when using this basic catalyst. This observation was shown to be similar to results obtained by others using less basic catalysts in the batch mode. The relative rates of these reactions are different in a batch reactor than in a continuous stirred tank reactor. This difference in relative rates is due to the fact that at any degree of advancement in the batch system, the products have a history of previous products, pH, and dissolved catalyst. The relative rate differences can be expected to yield a different nature of product sugars for the two types of reactors.

Magnesium alloys and graphite wastes encapsulated in cementitious materials: Reduction of galvanic corrosion using alkali hydroxide activated blast furnace slag

Energy Technology Data Exchange (ETDEWEB)

Chartier, D., E-mail: david.chartier@cea.fr [Commissariat à l' Energie Atomique et aux Energies Alternatives, CEA, DEN, DTCD, SPDE, F-30207 Bagnols-sur-Cèze (France); Muzeau, B. [DEN-Service d’Etude du Comportement des Radionucléides (SECR), CEA, Université Paris-Saclay, F-91191, Gif-sur-Yvette (France); Stefan, L. [AREVA NC/D& S - France/Technical Department, 1 place Jean Millier 92084 Paris La Défense (France); Sanchez-Canet, J. [Commissariat à l' Energie Atomique et aux Energies Alternatives, CEA, DEN, DTCD, SPDE, F-30207 Bagnols-sur-Cèze (France); Monguillon, C. [DEN-Service d’Etude du Comportement des Radionucléides (SECR), CEA, Université Paris-Saclay, F-91191, Gif-sur-Yvette (France)

2017-03-15

Highlights: • Embedded in cement, magnesium is corroded by residual water present in porosity of the matrix. • Corrosion is enhanced by galvanic phenomenon when magnesium is in contact with graphite. • Galvanic corrosion of magnesium in contact with graphite debris is shown to be severe with ordinary Portland cement. • Galvanic corrosion is significantly lowered in high alkali medium such as sodium hydroxide. • Sodium hydroxide activated blast furnace slag is a convenient binder to embed magnesium. - Abstract: Magnesium alloys and graphite from spent nuclear fuel have been stored together in La Hague plant. The packaging of these wastes is under consideration. These wastes could be mixed in a grout composed of industrially available cement (Portland, calcium aluminate…). Within the alkaline pore solution of these matrixes, magnesium alloys are imperfectly protected by a layer of Brucite resulting in a slow corrosion releasing hydrogen. As the production of this gas must be considered for the storage safety, and the quality of wasteform, it is important to select a cement matrix capable of lowering the corrosion kinetics. Many types of calcium based cements have been tested and most of them have caused strong hydrogen production when magnesium alloys and graphite are conditioned together because of galvanic corrosion. Exceptions are binders based on alkali hydroxide activated ground granulated blast furnace slag (BFS) which are presented in this article.

Magnesium alloys and graphite wastes encapsulated in cementitious materials: Reduction of galvanic corrosion using alkali hydroxide activated blast furnace slag

International Nuclear Information System (INIS)

Chartier, D.; Muzeau, B.; Stefan, L.; Sanchez-Canet, J.; Monguillon, C.

2017-01-01

Highlights: • Embedded in cement, magnesium is corroded by residual water present in porosity of the matrix. • Corrosion is enhanced by galvanic phenomenon when magnesium is in contact with graphite. • Galvanic corrosion of magnesium in contact with graphite debris is shown to be severe with ordinary Portland cement. • Galvanic corrosion is significantly lowered in high alkali medium such as sodium hydroxide. • Sodium hydroxide activated blast furnace slag is a convenient binder to embed magnesium. - Abstract: Magnesium alloys and graphite from spent nuclear fuel have been stored together in La Hague plant. The packaging of these wastes is under consideration. These wastes could be mixed in a grout composed of industrially available cement (Portland, calcium aluminate…). Within the alkaline pore solution of these matrixes, magnesium alloys are imperfectly protected by a layer of Brucite resulting in a slow corrosion releasing hydrogen. As the production of this gas must be considered for the storage safety, and the quality of wasteform, it is important to select a cement matrix capable of lowering the corrosion kinetics. Many types of calcium based cements have been tested and most of them have caused strong hydrogen production when magnesium alloys and graphite are conditioned together because of galvanic corrosion. Exceptions are binders based on alkali hydroxide activated ground granulated blast furnace slag (BFS) which are presented in this article.

Histologic evaluation of pulpotomy performed with ethyl-cyanoacrylate and calcium hydroxide Avaliação histológica de pulpotomia realizada com etil-cianoacrilato e com hidróxido de cálcio

Directory of Open Access Journals (Sweden)

Diana Santana de Albuquerque

2006-09-01

Full Text Available The aim of this study was to evaluate histological aspects of the pulp-dentin complex of dogs submitted to pulpotomy and capped with ethyl-cyanoacrylate and calcium hydroxide. Thirty dog teeth were divided into 2 groups of 15 as follows: Group 1 - ethyl-cyanoacrylate; Group 2 - calcium hydroxide. The pulpotomies were carried out following all of the treatment precautions recommended for dogs. After 30 days the specimens were submitted to histological preparation and were then blindly evaluated by a histologist. Data were analyzed statistically by the Fisher exact test, comparing the two groups. After 30 days, the presence of a hard tissue barrier was observed in 83.3% of Group 1, and in 100% of Group 2 (p = 0.478. A continuous hard tissue barrier was observed in 50% of the ethyl-cyanoacrylate group and 75% of the calcium hydroxide group (p = 0.652. It can be concluded that both materials induced hard tissue barrier formation, but Group 2 had a higher percentage than Group 1, with no significant statistical differences; the differences observed between the different barriers (continuous/non-continuous were not significant between groups and there was no pulpal necrosis in either group.O objetivo do presente estudo foi avaliar o aspecto histológico do complexo dentino-pulpar de cachorros quando capeado após a pulpotomia com etil-cianoacrilato e hidróxido de cálcio. Trinta dentes de cães foram divididos em 2 grupos de 15 da seguinte forma: Grupo 1 - Etil-cianoacrilato; Grupo 2 - Hidróxido de cálcio. A pesquisa foi realizada tomando-se todos os cuidados recomendados para o tratamento com os cães. Após 30 dias do procedimento realizado os espécimes foram submetidos ao preparo histológico e logo após foram avaliados de forma cega por um histologista. Os resultados foram analisados estatisticamente através do Teste Exato de Fisher. No grupo 1, 83,3% e no grupo 2, 100% dos dentes apresentaram a barreira de tecido duro (p = 0,478. A barreira

Effect of substrate nature on the electrochemical deposition of calcium-deficient hydroxyapatites

International Nuclear Information System (INIS)

Gualdrón-Reyes, A F; Cabanzo, R; Meléndez, A M; Domínguez-Vélez, V; Morales-Morales, J A

2017-01-01

Calcium phosphates were obtained by reducing nitrate ions to produce hydroxide ions on TiO 2 /stainless steel and TiO 2 /titanium electrodes. TiO 2 coatings on metallic substrates were prepared by sol-gel dip-coating method. The morphology of deposits was observed by FESEM. Chemical nature of calcium phosphate deposits was identified by Raman micro-spectroscopy and FESEM/EDS microanalysis. Electrochemical behavior of nitrate and nitrite reduction on stainless steel and titanium electrodes was studied by linear sweep voltammetry. In addition, voltammetric study of the calcium phosphate electrodeposition on both electrodes was performed. From these measurements was selected the potential to form a calcium phosphate. A catalytic current associated to nitrate reduction reaction was obtained for stainless steel electrode, leading to significant deposition of calcium phosphate. Ca/P ratio for both substrates was less than 1.67. The formation of calcium deficient hydroxyapatite was confirmed by Raman spectroscopy. (paper)

ACTIVATION AND REACTIVITY OF NOVEL CALCIUM-BASED SORBENTS FOR DRY SO2 CONTROL IN BOILERS

Science.gov (United States)

Chemically modified calcium hydroxide (Ca(OH)2) sorbents developed in the U.S. Environmental Protection Agency's Air and Energy Engineering Research Laboratory (AEERL) for sulfur dioxide (SO2) control in utility boilers were tested in an electrically heated, bench-scale isotherma...

Preparation and properties of calcium zirconate

International Nuclear Information System (INIS)

Dudek, M.; Bucko, M.; Rog, G.

2001-01-01

Dense samples of calcium zirconate were prepared. Electrical conductivity of the samples were measured in the temperature range 873 - 1273 K by both the d.c. four probe and the impedance spectroscopy methods. Calcium zirconate with small excess of calcium oxide appeared to be oxygen ion conductor. It was applied as an electrolyte in solid-state galvanic cells. (author)

Gold Nanoparticles on Layered Double Hydroxide Nanosheets and Its Electrocatalysis for Glucose Oxidation

Energy Technology Data Exchange (ETDEWEB)

Cho, Hye Ran; Lee, Jong Hyeon [The Catholic University of Korea, Bucheon (Korea, Republic of); Cho, Se Hee; Ji, Hong Geun [H and A PharmaChem, Bucheon (Korea, Republic of)

2016-03-15

We developed a new way to form the well-defined nanocomposite of Au NPs and exfoliated LDH nanosheet by in situ chemical reduction with NaBH{sub 4}. The optical and structural studies indicate that the Au NPs are highly dispersed and immobilized on the surface of LDH nanosheets. The Au/LDH nanosheet exhibited an excellent electrocatalysis toward glucose oxidation reaction. The results strongly demonstrate that the nanoscopic natures and dense positive charges of LDH nanosheet effectively stabilized the Au NPs to maintain their inherent properties during the synthesis and the electrocatalysis. The use of the double hydroxide nanosheets as nanoscopic support materials for the transition-metal NPs will dramatically improve their functionalities in heterogeneous catalysis. Recently, two-dimensional nanosheet of exfoliated layered double hydroxide (LDH) has emerged as a new type of solid support to immobilize the diverse metal NPs because of the large metal hydroxide area, good biochemical stability, and highly charged positive potential of 1- to 2-nm thick LDH layers. LDHs consist of a continuous stack of positively charged metal hydroxide layers with counter anions and water molecules placed in interlayer spaces.

21 CFR 184.1631 - Potassium hydroxide.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Potassium hydroxide. 184.1631 Section 184.1631 Food... Specific Substances Affirmed as GRAS § 184.1631 Potassium hydroxide. (a) Potassium hydroxide (KOH, CAS Reg... pellets, flakes, sticks, lumps, and powders. Potassium hydroxide is obtained commercially from the...

Synthesis of hydroxyapatite with the use of calcium carbonate as of the biological precursor

International Nuclear Information System (INIS)

Aguilar, M.S.; Di Lello, B.C.; Queiroz, F.; Campos, N.C.; Campos, J.B.

2014-01-01

This work describes the synthesis of hydroxyapatite from calcium from biological materials such as shells carbonate. In the syntheses performed, the calcium carbonate of biological origin was used as the precursor and through a precipitation reaction with phosphoric acid, was converted into calcium hydroxide. Sequentially, the precipitate was aged, filtered, washed, dried and calcined, and then transformed into hydroxyapatite. The characterization of the powders was performed by X-DR (X-ray diffraction) and SEM (scanning electron microscopy). DR-X as determined hydroxyapatite calcium phosphate phase calcium. SEM revealed a morphology of finely divided particles. The method B.E.T. showed values of specific area and volume of micropores consistent with the literature. The results of the characterizations proved feasible to use for obtaining biological hydroxyapatite materials used in the reaction conditions.(author)

Recovery of calcium carbonate from steelmaking slag and utilization for acid mine drainage pre-treatment

CSIR Research Space (South Africa)

Mulopo, J

2012-06-01

Full Text Available The conversion of steelmaking slag (a waste product of the steelmaking process) to calcium carbonate (CaCO3) was tested using hydrochloric acid, ammonium hydroxide and carbon dioxide via a pH-swing process. Batch reactors were used to assess...

Formation of mixed hydroxides in the thorium chloride-iron chloride-sodium hydroxide system

International Nuclear Information System (INIS)

Krivokhatskij, A.S.; Prokudina, A.F.; Sapozhnikova, T.V.

1976-01-01

The process of formation of mixed hydroxides in the system thorium chloride-iron chloride-NaOH was studied at commensurate concentrations of Th and Fe in solution (1:1 and 1:10 mole fractions, respectively) with ionic strength 0.3, 2.1, and 4.1, created with the electrolyte NaCl, at room temperature 22+-1degC. By the methods of chemical, potentiometric, thermographic, and IR-spectrometric analyses, it was shown that all the synthesized precipitates are mechanical mixtures of two phases - thorium hydroxide and iron hydroxide - and not a new hydrated compound. The formal solubility of the precipitates of mixed hydroxides was determined. It was shown that the numerical value of the formal solubility depends on the conditions of formation and age of the precipitates

Alkali Influence on Synthesis of Solid Electrolyte Based on Alkali Nitrate-Alumina

International Nuclear Information System (INIS)

Yustinus Purwamargapratala; Purnama, S.; Purwanto, P.

2008-01-01

Research of solid electrolyte based on alumina with addition of alkali materials of barium nitrate, calcium nitrate, sodium nitrate and lithium nitrate has been done. Aluminium hydroxide and alkali nitrate were mixed in mole ratio of 1 : 1 in water media and pyrolyzed at 300 o C for 1 hour Pyrolysis result were then mixed with alumina in mole ratio of 1 : 1, compacted and heated at 600 o C for 3 hours. To characterize the sample, XRD (X-Ray Diffractometers) and LCR meter (impedance, capacitance, and resistance) were used for analysis the phase and conductivity properties. The result showed formation of alkali-aluminate in which Li-base have the highest room temperature conductivity of 3.1290 x 10 -5 S.cm -1 , while Ba-base have the lowest conductivity of 5.7266 x 10 -8 S.cm -1 . (author)

The formation reaction of calcium hexa-aluminate

International Nuclear Information System (INIS)

Tuganova, S.Kh.; Sirajiddinov, N.A.

1990-01-01

The formation reaction of CaAl 12 O 19 at interaction of calcium oxide and aluminium in solid form has been studied. Some physical-chemical characteristics of calcium hexa-aluminate are given. (author)

Effect of Postharvest Oxalic Acid and Calcium Chloride on Quality Attributes of Sweet Cherry (Prunus avium L.

Directory of Open Access Journals (Sweden)

M. Safa

2016-02-01

Full Text Available Introduction: Fruits and vegetables have special importance as a very important part of the human food supply. And from the beginnings of life, man has used these products to supply a part of his food. Nowadays, horticultural products are widely used in the diet. Cherry is one of the deciduous trees in the temperate regions, which is potassium rich. Use of Oxalic acid significantly reduces frost injury in pomegranate fruits during storage at a temperature of 2° C. In fruit trees, the importance of calcium is due to a delay in fruit ripening process and this way products have better portability. Materials and Methods: Firmness test was measured using the FT011 model of penetrometer. For determination of titratable acidity, the 0.1 N sodium hydroxide (NaOH titration method was used. Total Soluble solids content (SSC of fruit was measured by a digital refractometer (PAL-1. For determination of vitamin C in fruit juices, titration method with the indicator, 2,6-di-chlorophenolindophenol was used. Fruit juice pH was measured using pH meter model HI 9811.In order to investigate the effect of postharvest soaking treatment with Oxalic acid on the qualitative specifications and storage life of single grain sweet cherry fruit a research was conducted. This experience was conducted in a completely randomized design with 3 replications separately for the two materials. In this experiment Oxalic acid, in four levels (0,4,6 and 8 mM and Calcium chloride in four levels (0, 40, 55 and 70 mM were applied on the single grain sweet cherry fruit in the form of soaking and sampleswith7-day intervals for a period of 28 days from the fridge out and quanti tate and qualitative traits such as stiffness, weight loss, Titratable acidity, total soluble solids, vitamin C and pH were measured. Results and Discussion: The results showed that compared with control ones all of the concentrations of Oxalic acid and Calcium chloride caused significant differences in the amount

Pyrochemical recovery of plutonium from calcium fluoride reduction slag

Science.gov (United States)

Christensen, D.C.

A pyrochemical method of recovering finely dispersed plutonium metal from calcium fluoride reduction slag is claimed. The plutonium-bearing slag is crushed and melted in the presence of at least an equimolar amount of calcium chloride and a few percent metallic calcium. The calcium chloride reduces the melting point and thereby decreases the viscosity of the molten mixture. The calcium reduces any oxidized plutonium in the mixture and also causes the dispersed plutonium metal to coalesce and settle out as a separate metallic phase at the bottom of the reaction vessel. Upon cooling the mixture to room temperature, the solid plutonium can be cleanly separated from the overlying solid slag, with an average recovery yield on the order of 96 percent.

Mineralogy of C-S-H belite hydrates incorporating Zn-Al-Ti layered double hydroxides

Directory of Open Access Journals (Sweden)

Amor F.

2018-01-01

Full Text Available Recently, the belitic cements with low alite content were the subject of several research works which aimed to replace the Ordinary Portland Clinker (OPC for ecological reasons (reduction of CO2 emissions, so to understand the reactivity of this cement, the hydration study of the C2S “dicalcium silicate” phase is primordial research step. As well for a clean environment, the TiO2 photocatalyst has been extensively applied in the science of building materials because of its ability to degrade the cement surface pollutants. New photocatalyst based layered double hydroxides (LDH associated with zinc, aluminium and TiO2 was introduced to increase the compatibility with mortars. The present work is subjected to investigate the effect of the layered double hydroxides on the hydration of C2S in following the evolution of hydration by X-ray diffraction at 2, 7, 28 and 90 days and analyzing the calcium/silicon ratio of different formed hydrates.

A histological evaluation of bone tissue response to a sealer based on calcium hydroxide: An experimental study

Directory of Open Access Journals (Sweden)

Nikolić Marija

2017-01-01

Full Text Available Introduction/Objective. The success of endodontic treatment depends on the effective removal of root content, the elimination of infection, and the hermetical sealing of the root system using a compatible material. The objective of this paper was to evaluate the tissue response to the implant of endodontic material based on calcium hydroxide into the bone in the artificially prepared defect in a rat mandible. Methods. The research was carried out on 40 Wistar rats. The artificial defect was made between the midline and the mental foramen on the left side of the mandible. The prepared defect was left to heal spontaneously in animals of the control group, while among the animals of the experimental group the sealer Apexit (Ivoclar Vivadent, Schaan, Lichtenstein was implanted into the experimental defect. The tissue samples consisting of the experimental field and the surrounding bone were microscopically analyzed with a light microscope. Results. During the initial phase, 15 days after the implantation, signs of chronic inflammation were noted and expansion of the Volkmann’s and Haversian canals. On the 30th day after the implantation, osteosynthetic activity and filling with newly-formed bone were noted. Changes were also noted in cement lines in the wider region of the experimental defect. Sixty days following the implantation, the bone was gradually remodeled. Ninety days after the implantation, a restitutio ad integrum was noted. Conclusion. Apexit does not lead to any disruptions in normal reparation processes nor in morphofunctional relations in bone tissue during the remodeling phase. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. 175061: The antioxidant protection and potentials for differentiation and regeneration of mesenchymal stem cells from different tissues during the aging process

Direct transformation of calcium sulfite to {alpha}-calcium sulfate hemihydrate in a concentrated Ca-Mg-Mn chloride solution under atmospheric pressure

Energy Technology Data Exchange (ETDEWEB)

Baohong Guan; Hailu Fu; Jie Yu; Guangming Jiang; Bao Kong; Zhongbiao Wu [Zhejiang University, Hangzhou (China). Department of Environmental Engineering

2011-01-15

Massive quantities of sulfite-rich flue gas desulfurization (FGD) scrubber sludge have been generated by coal burning power plants. Utilization of the sulfite-rich sludge for preparing {alpha}-calcium sulfate hemihydrate ({alpha}-HH), an important kind of cementitious material, is of particular interest to electric utilities and environmental preservation. In the experiment, calcium sulfite hemihydrate was directly transformed to {alpha}-HH without the occurrence of calcium sulfate dihydrate (DH). The transformation was performed in a concentrated CaCl{sub 2} solution containing Mg{sup 2+} and Mn{sup 2+} at 95{sup o}C, atmospheric pressure and low pH. The oxidation of calcium sulfite and the subsequent crystallization of {alpha}-HH constitute the whole conversion, during which the oxidation turns out to be the rate controlling step. Solid solution comprised of calcium sulfite hemihydrate and calcium sulfate was found to coexist with {alpha}-HH in the suspension. Calcium sulfate increases and calcium sulfite decreases spontaneously until the solid solution disappears. Thus, it is a potential alternative to utilize sulfite-rich FGD scrubber sludge for the direct preparation of {alpha}-HH. 36 refs., 10 figs., 1 tab.

Short-term vs long-term calcium hydroxide therapy after immediate tooth replantation: a histomorphometric study in monkey's teeth.

Science.gov (United States)

Panzarini, Sônia Regina; Gulinelli, Jéssica Lemos; Saito, Célia T M H; Poi, Wilson Roberto; Sonoda, Celso Koogi; Américo de Oliveira, José; Melo, Moriel Evangelista; de Souza Gomes, Weglis Dyanne

2012-06-01

Endodontic treatment is an important step of tooth replantation protocols, but the ideal moment for definitive obturation of replanted teeth has not yet been established. In this study, a histomorphometric analysis was undertaken to evaluate the repair process on immediate replantation of monkey's teeth after calcium hydroxide (CH) therapy for 1 and 6 months followed by root canal filling with a CH-based sealer (Sealapex(®) ). The maxillary and mandibular lateral incisors of five female Cebus apella monkeys were extracted, kept in sterile saline for 15 min, replanted and splinted with stainless steel orthodontic wire and composite resin for 10 days. In Group I (control), definitive root canal filling was performed before tooth extraction. In Groups II and III, CH therapy started after removal of splint, and definitive root canal filling was performed 1 and 6 months later, respectively. The animals were euthanized 9 months after replantation, and specimens were processed for histomorphometric analysis. In all groups, epithelial attachment occurred at the cementoenamel junction or very close to this region; the areas of resorption on root surface had small extension and depth and were repaired by newly formed cementum; and the periodontal ligament was organized. Statistical analysis of the scores obtained for the histomorphometric parameters did not show any statistically significant difference (P = 0.1221) among the groups. The results suggests that when endodontic treatment is initiated 10 days after immediate replantation and an antibiotic regimen is associated, definitive root canal filling can be performed after a short-term CH therapy. © 2011 John Wiley & Sons A/S.

Influence of calcium hydroxide on dyes for dentin labeling, anlyzed by means of a new methodology Influência do hidróxido de cálcio sobre corantes na marcação dentinária, analisada por meio de uma nova metodologia

Directory of Open Access Journals (Sweden)

Ivaldo Gomes de Moraes

2005-09-01

Full Text Available The objective of this study was to evaluate the influence of calcium hydroxide in intracanal dressing on the ability of the dyes rhodamine B and methylene blue to label the dentine. Forty extracted human mandibular premolars had their canals instrumented and were divided into four groups: in two groups, the canals were filled with a calcium hydroxide paste and the others remained in distilled water. After 15 days, in two groups (with and without dressing, the canals were obturated with sealer containing methylene blue, whereas the others contained rhodamine B. For analysis, the roots were transversally sectioned in their cervical, medium and apical thirds, and the labeling was analyzed. The Mann-Whitney test showed statistically significant difference between the dressing/methylene blue group and the others. Based on these results, it was concluded that calcium hydroxide in intracanal dressing negatively interferes with the labeling ability of methylene blue.Objetivou-se avaliar a influência do curativo intracanal de hidróxido de cálcio sobre a capacidade dos corantes azul de metileno e rhodamine B de marcar a dentina, quando incorporados à massa obturadora, no momento da espatulação. Quarenta pré-molares inferiores humanos extraídos tiveram seus canais instrumentados sendo, então, divididos em quatro grupos. Em dois grupos, os canais foram preenchidos com pasta de hidróxido de cálcio e propilenoglicol por 15 dias. Os outros, permaneceram em água destilada. Após a remoção do curativo, todos os canais foram obturados com condensação lateral e cimento de óxido de zinco e eugenol acrescidos de azul de metileno ou rhodamine B. Assim, em dois grupos (com e sem curativo, os canais foram obturados com cimento contendo azul de metileno e os outros, rhodamine B. Decorridos 15 dias, as raízes foram seccionadas transversalmente nos terços cervical, médio e apical, procedendo-se à análise da marcação, com atribuição de escores �

The in vitro antibacterial effect of iodine-potassium iodide and calcium hydroxide in infected dentinal tubules at different time intervals.

Science.gov (United States)

Lin, Shaul; Kfir, Anda; Laviv, Amir; Sela, Galit; Fuss, Zvi

2009-03-01

The aim of this study was to evaluate the antibacterial effect of iodine-potassium iodide (IKI) and calcium hydroxide (CH) on dentinal tubules infected with Enterococcus faecalis (E. faecalis) at different time intervals. Hollow cylinders of bovine root dentin (n=45) were infected and divided into three equal groups filled with either IKI or CH and a positive control. After placing each medicament in the infected cylinders for time periods of 10 minutes, 48 hours and 7 days, microbiological samples were analyzed. At the end of each period, four 100 microm thick inner dentin layers (400 microm thick from each specimen) were removed using dental burs of increasing diameters. Dentin powder was cultured on agar plates to quantitatively assess their infection, expressed in colony forming units (cfu). In all layers of the positive control group, heavy bacterial infection was observed. After 10 minutes, IKI reduced the amount of viable bacteria more efficiently than CH, whereas at later time intervals CH showed the best results. For short periods of exposure, IKI has a more efficient antibacterial effect in the dentinal tubules than CH but CH performs better after longer durations of exposure. This research indicates the use of IKI is a better choice for disinfecting the root canal than CH if only a short duration of exposure is used because of its more efficient antibacterial effect. However, if a longer exposure time is used, then CH is a better choice because of its better disinfecting effect over time.

Structural characterization of pure and doped calcium phosphate bioceramics prepared by simple solid state method

International Nuclear Information System (INIS)

Ahmed, S.; Kabir, H.; Nigar, F.

2011-01-01

Calcium Phosphate based bioceramic materials, in pure and doped forms have been successfully synthesized from egg shells by using solid-state method for the first time. Considering the diverse role of zinc and fluoride in biological functions, these two ions were chosen to develop the substituted bioceramic materials. Structural characterizations of these developed bioceramics were performed by using FTIR, XRD, SEM and EDS techniques. The results revealed that the fluoride doped apatite was formed in single phase containing hydroxyapatite while pure and Zinc doped apatites contained -TCP with hydroxyapatite. Experimental results and the crystallographic parameters matched well with the literature values indicating that the present experimental protocol favoured the formation of the desired bioceramics. However, to synthesize the (Ca (PO)) based bioceramic materials, such a simple solid-state approach would obviously be very helpful, not only in making the process economically feasible, but also in creating an effective material recycling technology for waste-management. (author)

21 CFR 582.1631 - Potassium hydroxide.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Potassium hydroxide. 582.1631 Section 582.1631 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Additives § 582.1631 Potassium hydroxide. (a) Product. Potassium hydroxide. (b) Conditions of use. This...

Solid Soap Production using Plantain Peel Ash as Source of Alkali ...

African Journals Online (AJOL)

A neat soap, which was milky white in colour, was obtained when the improved ash extract was reacted with the bleached oil blend. This was also the colour of two other soaps made from pure potassium hydroxide and pure sodium hydroxide alkalis, respectively and the same bleached oil blend. It was concluded that solid ...

Radium behaviour during ferric oxi-hydroxides crystallization

International Nuclear Information System (INIS)

Bassot, S.; Stammose, D.; Benitah, S.

2004-01-01

In uranium mill tailings, oxides and oxi-hydroxides are responsible of about 70% of the radium immobilization, half being associated to amorphous forms (mainly hydrous ferric oxides and hydrous manganese oxides). With time, crystallization of these amorphous forms can occur, inducing a redistribution of radium between solid and solution. If the amount of mobile radium increases, the impact of these tailings on the environment may become significant. The aim of this study is to determine the amount of radium released in solution during the crystallization process of hydrous ferric oxide (HFO). The transformation of Ra-HFO co-precipitate in crystallized forms (goethite, hematite, is studied by ageing at 40 deg C for different solution compositions. Both solids and solutions are sampled for different times and analysed. The solid evolution is followed by specific area measurements (about 250 m2/g for HFO and about 10-20 m 2 /g for crystallized form) and by determination of the amorphous fraction according to a selective extraction procedure. The solutions were analysed for 226 radium activity, iron concentration and pH. In order to discriminate the part of radium included in the solid and the part of radium fixed on the solid surface, radium sorption onto HFO and crystallized forms is studied as a function of pH. The modelling of the sorption curves with JCHESS 2.0 code allow to point out the mechanisms responsible of the 226-radium distribution between solid and solution during the crystallization process of HFO. (author)

Calcium ion binding to a soil fulvic acid using a Donnan Potential model

International Nuclear Information System (INIS)

Marinsky, J.A.

1999-01-01

Calcium ion binding to a soil fulvic acid (Armadale Bh Horizon) was evaluated over a range of calcium ion concentrations, from pH 3.8 to 7.3, using potentiometric titrations and calcium ion electrode measurements. Fulvic acid concentration was constant (100 milligrams per liter) and calcium ion concentration varied up to 8 x 10 -4 moles per liter. Experiments discussed here included: (1) titrations of fulvic acid-calcium ion containing solutions with sodium hydroxide; and (2) titrations of fully neutralized fulvic acid with calcium chloride solutions. Apparent binding constants (expressed as the logarithm of the value, log β app ) vary with solution pH, calcium ion concentration, degree of acid dissociation, and ionic strength (from log β app =2.5 to 3.9) and are similar to those reported by others. Fulvic acid charge, and the associated Donnan Potential, influences calcium ion-fulvic acid ion pair formation. A Donnan Potential correction term allowed calculation of intrinsic calcium ion-fulvic acid binding constants. Intrinsic binding constants vary from 1.2 to 2.5 (the average value is about log β=1.6) and are similar to, but somewhat higher than, stability constants for calcium ion-carboxylic acid monodentate complexes. (orig.)

Evaluation of the Chemical and Mechanical Properties of Hardening High-Calcium Fly Ash Blended Concrete.

Science.gov (United States)

Fan, Wei-Jie; Wang, Xiao-Yong; Park, Ki-Bong

2015-09-07

High-calcium fly ash (FH) is the combustion residue from electric power plants burning lignite or sub-bituminous coal. As a mineral admixture, FH can be used to produce high-strength concrete and high-performance concrete. The development of chemical and mechanical properties is a crucial factor for appropriately using FH in the concrete industry. To achieve sustainable development in the concrete industry, this paper presents a theoretical model to systematically evaluate the property developments of FH blended concrete. The proposed model analyzes the cement hydration, the reaction of free CaO in FH, and the reaction of phases in FH other than free CaO. The mutual interactions among cement hydration, the reaction of free CaO in FH, and the reaction of other phases in FH are also considered through the calcium hydroxide contents and the capillary water contents. Using the hydration degree of cement, the reaction degree of free CaO in FH, and the reaction degree of other phases in FH, the proposed model evaluates the calcium hydroxide contents, the reaction degree of FH, chemically bound water, porosity, and the compressive strength of hardening concrete with different water to binder ratios and FH replacement ratios. The evaluated results are compared to experimental results, and good consistencies are found.

Experimental investigation of the effect of latex solid/water ratio on latex modified co-matrix mechanical properties

Directory of Open Access Journals (Sweden)

Ahmed M. Diab

2013-03-01

Full Text Available Numerous researches were performed on latex modified concretes and associated properties, however; some vital factors were not given attention in previous works. This study focus on new factor which significantly affects the properties of latex modified cement paste, mortar or concrete. This factor is termed as ‘latex solid/water ratio’ which is defined herein as the ratio of weight of solid latex to weight of total water content of cement composite including the water in latex itself. The effect of this factor on some properties of cement paste, mortar and concrete were experimentally evaluated. Properties of cement paste include the produced calcium hydroxide and ettringite content during hydration process, while those of cement mortar take account of absorption and effect of temperature on compressive strength. Furthermore, the effect of this factor on the compressive and flexural strengths, modulus of elasticity, water penetration depth and drying shrinkage of concrete were explored. Based on experimental evidences, and spite of using different cement contents, sources of latex, water–cement ratios and slump values, it can be generally concluded that the latex solid/water ratio is a dominant factor affecting different properties of latex modified mortars and concrete.

Two-way Valorization of Blast Furnace Slag: Synthesis of Precipitated Calcium Carbonate and Zeolitic Heavy Metal Adsorbent.

Science.gov (United States)

Georgakopoulos, Evangelos; Santos, Rafael M; Chiang, Yi Wai; Manovic, Vasilije

2017-02-21

The aim of this work is to present a zero-waste process for storing CO2 in a stable and benign mineral form while producing zeolitic minerals with sufficient heavy metal adsorption capacity. To this end, blast furnace slag, a residue from iron-making, is utilized as the starting material. Calcium is selectively extracted from the slag by leaching with acetic acid (2 M CH3COOH) as the extraction agent. The filtered leachate is subsequently physico-chemically purified and then carbonated to form precipitated calcium carbonate (PCC) of high purity (Sodium hydroxide is added to neutralize the regenerated acetate. The morphological properties of the resulting calcitic PCC are tuned for its potential application as a filler in papermaking. In parallel, the residual solids from the extraction stage are subjected to hydrothermal conversion in a caustic solution (2 M NaOH) that leads to the predominant formation of a particular zeolitic mineral phase (detected by XRD), namely analcime (NaAlSi2O6∙H2O). Based on its ability to adsorb Ni 2+ , as reported from batch adsorption experiments and ICP-OES analysis, this product can potentially be used in wastewater treatment or for environmental remediation applications.

Mechanisms of scale formation and carbon dioxide partial pressure influence. Part I. Elaboration of an experimental method and a scaling model.

Science.gov (United States)

Gal, Jean-Yves; Fovet, Yannick; Gache, Nathalie

2002-02-01

Scale formation in industrial or domestic installations is still an important economic problem. The existence of a metastable domain for calcium carbonate supersaturated solutions and its breakdown are observed under conditions rarely well defined. In most cases it is the pH rise caused by the carbon dioxide loss that involves calcium carbonate precipitation. Before studying this problem, we suggest in this first part, a new model for the evolution of the calcocarbonic system that takes into account the hydrated forms of CaCO3: CaCO3 amorphous, CaCO3 x 6H2O (ikaite) and CaCO3 x H2O (monohydrate). According to this model, the precipitation of any one of these hydrated forms could be responsible for the breakdown of the metastable state. After this first step, the solids evolve into dehydrated forms. At first, the metastable domain spread of the calcium carbonate supersaturated solutions was studied by the elaboration of computer programs in which the formation of CaCO3(0)(aq) ion pairs was taken into account. These ion pairs are supposed to evolve through dehydration to form the various calcium carbonate solid form precursors. This thermodynamic study was then compared to the experimental methods of the critical pH. Here the pH rise was caused by adding sodium hydroxide under different conditions for sodium hydroxide addition speed, agitation mode and ageing of solutions. For the highest speed of sodium hydroxide addition, the CaCO3 ionic product reached the value of the amorphous calcium carbonate solubility product, and the reaction of the amorphous calcium carbonate precipitation was of the homogenous type. Decreasing the reagent's addition speed caused an extension of the titration time. Then, the breakdown of the metastable state was obtained with the CaCO3 x H2O heterogeneous precipitation. This clearly illustrates the probable ageing of the precursors of the solid states that are considered in this model.

Effect of pH on Separation of Solid Content from Paint Contained Wastewater by a Coagulant-flocculant Compound

Directory of Open Access Journals (Sweden)

Mojtaba Semnani Rahbar

2014-05-01

Full Text Available Chemical wastewater treatment is one of the attracting and common methods for wastewater treatment among the currently employed chemical unit processes. The use of coagulant-flocculant compound is one of the efficient methods for separating of paint and recovery of water. In this research, it was introduced and the effect of pH on removal of solid content from solution was studied experimentally. For this purpose, sludge and suspended solid content of the solution were determined in a jar test by measurement of UV absorption of treated solution and solid separation percentage. The results showed that in pH range 9.5-10.5, maximum efficiency of solid content removal was up to 95%. Consequently, maximum paint removal was obtained in this range of pH. The separation of solid content of the solution was due to formation of aluminum hydroxide. As shown by the results, the reduction of potassium hydroxide as pH adjuster caused decrease of pH and consequently decreases of aluminum hydroxide and solid content removal.  

Radiochemical study of the sorption of iodate ions on iron(III) hydroxide precipitate

International Nuclear Information System (INIS)

Music, S.; Sipalo-Zuljevic, J.; Wolf, R.H.H.

1980-01-01

The sorption of iodate ions on iron(III) hydroxide in dependence on the pH, the aging time of the precipitate and the duration of the contact between the sorbate and the sorbent have been studied. Na 131 IO 3 was used as a radioactive indicator. The sorption mechanism has been discussed in terms of electrostatic and ion-exchange processes at the solid/liquid interface. (author)

Structural transformation of nickel hydroxide films during anodic oxidation

Energy Technology Data Exchange (ETDEWEB)

Crocker, Robert W. [Univ. of California, Berkeley, CA (United States); Muller, Rolf H. [Univ. of California, Berkeley, CA (United States)

1992-05-01

The transformation of anodically formed nickel hydroxide/oxy-hydroxide electrodes has been investigated. A mechanism is proposed for the anodic oxidation reaction, in which the reaction interface between the reduced and oxidized phases of the electrode evolves in a nodular topography that leads to inefficient utilization of the active electrode material. In the proposed nodular transformation model for the anodic oxidation reaction, nickel hydroxide is oxidized to nickel oxy-hydroxide in the region near the metal substrate. Since the nickel oxy-hydroxide is considerably more conductive than the surrounding nickel hydroxide, as further oxidation occurs, nodular features grow rapidly to the film/electrolyte interface. Upon emerging at the electrolyte interface, the reaction boundary between the nickel hydroxide and oxy-hydroxide phases spreads laterally across the film/electrolyte interface, creating an overlayer of nickel oxy-hydroxide and trapping uncharged regions of nickel hydroxide within the film. The nickel oxy-hydroxide overlayer surface facilitates the oxygen evolution side reaction. Scanning tunneling microscopy of the electrode in its charged state revealed evidence of 80 - 100 Angstrom nickel oxy-hydroxide nodules in the nickel hydroxide film. In situ spectroscopic ellipsometer measurements of films held at various constant potentials agree quantitatively with optical models appropriate to the nodular growth and subsequent overgrowth of the nickel oxy-hydroxide phase. A two-dimensional, numerical finite difference model was developed to simulate the current distribution along the phase boundary between the charged and uncharged material. The model was used to explore the effects of the physical parameters that govern the electrode behavior. The ratio of the conductivities of the nickel hydroxide and oxy-hydroxide phases was found to be the dominant parameter in the system.

Structural transformation of nickel hydroxide films during anodic oxidation

Energy Technology Data Exchange (ETDEWEB)

Crocker, R.W.; Muller, R.H.

1992-05-01

The transformation of anodically formed nickel hydroxide/oxy-hydroxide electrodes has been investigated. A mechanism is proposed for the anodic oxidation reaction, in which the reaction interface between the reduced and oxidized phases of the electrode evolves in a nodular topography that leads to inefficient utilization of the active electrode material. In the proposed nodular transformation model for the anodic oxidation reaction, nickel hydroxide is oxidized to nickel oxy-hydroxide in the region near the metal substrate. Since the nickel oxy-hydroxide is considerably more conductive than the surrounding nickel hydroxide, as further oxidation occurs, nodular features grow rapidly to the film/electrolyte interface. Upon emerging at the electrolyte interface, the reaction boundary between the nickel hydroxide and oxy-hydroxide phases spreads laterally across the film/electrolyte interface, creating an overlayer of nickel oxy-hydroxide and trapping uncharged regions of nickel hydroxide within the film. The nickel oxy-hydroxide overlayer surface facilitates the oxygen evolution side reaction. Scanning tunneling microscopy of the electrode in its charged state revealed evidence of 80 {endash} 100 Angstrom nickel oxy-hydroxide nodules in the nickel hydroxide film. In situ spectroscopic ellipsometer measurements of films held at various constant potentials agree quantitatively with optical models appropriate to the nodular growth and subsequent overgrowth of the nickel oxy-hydroxide phase. A two-dimensional, numerical finite difference model was developed to simulate the current distribution along the phase boundary between the charged and uncharged material. The model was used to explore the effects of the physical parameters that govern the electrode behavior. The ratio of the conductivities of the nickel hydroxide and oxy-hydroxide phases was found to be the dominant parameter in the system.

Sorption of sulphur dioxide in calcium chloride and nitrate chloride liquids

International Nuclear Information System (INIS)

Trzepierczynska, I.; Gostomczyk, M.A.

1989-01-01

Flue gas desulphurization via application of suspensions has one inherent disadvantage: fixation of sulphur dioxide is very poor. This should be attributed to the low content of calcium ions which results from the solubility of the sorbing species. The solubility of sparingly soluble salts (CaO, CaCO 3 ) may be increased by decreasing the pH of the solution; yet, there is a serious limitation in this method: the corrosivity of the scrubber. The objective of this paper was to assess the sorbing capacity of two soluble calcium salts, calcium chloride and calcium nitrate, as a function of calcium ion concentration in the range of 20 to 82 kg/m 3 . It has been found that sorbing capacity increases with the increasing calcium ion concentration until the calcium concentration in the calcium chloride solution reaches the level of 60 kg/m 3 which is equivalent to the chloride ion content of ∼ 110 kg/m 3 . Addition of calcium hydroxide to the solutions brings about an increase in the sorbing capacity up to 1.6 kg/m 3 and 2.2 kg/m 3 for calcium chloride and calcium nitrate, respectively, as a result of the increased sorbent alkalinity. The sorption capacity of the solutions is considerably enhanced by supplementing them by acetate ions (2.8 to 13.9 kg/m 3 ). Increase in the sorption capacity of calcium nitrate solutions enriched with calcium acetate was approximately 30% as high as that of the chloride solutions enriched with calcium acetate was approximately 30% as high as that of the chloride solutions supplemented in the same way. (author). 12 refs, 7 refs, 4 tabs

Desalination and hydrogen, chlorine, and sodium hydroxide production via electrophoretic ion exchange and precipitation.

Science.gov (United States)

Shkolnikov, Viktor; Bahga, Supreet S; Santiago, Juan G

2012-08-28

We demonstrate and analyze a novel desalination method which works by electrophoretically replacing sodium and chloride in feed salt water with a pair of ions, calcium and carbonate, that react and precipitate out. The resulting calcium carbonate precipitate is benign to health, and can be filtered or settled out, yielding low ionic strength product water. The ion exchange and precipitation employs self-sharpening interfaces induced by movement of multiple ions in an electric field to prevent contamination of the product water. Simultaneously, the electrolysis associated with the electromigration produces hydrogen gas, chlorine gas, and sodium hydroxide. We conducted an experimental study of this method's basic efficacy to desalinate salt water from 100 to 600 mol m(-3) sodium chloride. We also present physicochemical models of the process, and analyze replacement reagents consumption, permeate recovery ratio, and energy consumption. We hypothesize that the precipitate can be recycled back to replacement reagents using the well-known, commercially implemented Solvay process. We show that the method's permeate recovery ratio is 58% to 46%, which is on par with that of reverse osmosis. We show that the method's energy consumption requirement over and above that necessary to generate electrolysis is 3 to 10 W h l(-1), which is on par with the energy consumed by state-of-the-art desalination methods. Furthermore, the method operates at ambient temperature and pressure, and uses no specialized membranes. The process may be feasible as a part of a desalination-co-generation facility: generating fresh water, hydrogen and chlorine gas, and sodium hydroxide.

Preparation, physical-chemical characterisation and cytocompatibility of calcium carbonate cements

OpenAIRE

Combes, Christèle; Miao, Baoji; Bareille, Reine; Rey, Christian

2006-01-01

The feasibility of calcium carbonate cements involving the recrystallisation of metastable calcium carbonate varieties has been demonstrated. Calcium carbonate cement compositions presented in this paper can be prepared straightforwardly by simply mixing water (liquid phase) with two calcium carbonate phases (solid phase) which can be easily obtained by precipitation. An original cement composition was obtained by mixing amorphous calcium carbonate and vaterite with an aqueous medium. The cem...

CH3SH adsorption properties and mechanism of deodorant filter made of iron hydroxide on porous iron frame; Tetsu takotaisei dasshu filter no methyl mercaptan jokyo seino to jokyo kiko

Energy Technology Data Exchange (ETDEWEB)

Noda, T. [Nippon Steel Corp., Tokyo (Japan)

1998-05-10

It is suggested that methyl mercaptan is decomposed to methyl sulfide and hydrogen by reaction with the a-iron hydroxide, and then the methyl sulfide combines with sulfur crystal and the hydrogen changes into water by the chemical reaction with the {alpha}-iron hydroxide. A deodorant filter was made by treating porous metallic iron with an aqueous solution of L-ascorbic acid, iron (II) sulfate and calcium hydroxide aqueous solution to deposit the iron ascorbate and the {alpha}-iron hydroxide on it. Then the deodorant filter was exposed to the hydrogen sulfide to yield the sulfur crystals on the surface of the deodorant filter. The methyl mercaptan removal capacity of the deodorant filter was studied with repetition of removal tests. Results show that the methyl mercaptan removal capacity of the deodorant filter is a little smaller than that of conventional granular activated carbon. 6 refs., 6 figs., 3 tabs.

Chromium and yttrium-doped magnesium aluminum oxides prepared from layered double hydroxides

Science.gov (United States)

García-García, J. M.; Pérez-Bernal, M. E.; Ruano-Casero, R. J.; Rives, V.

2007-12-01

Layered double hydroxides with the hydrotalcite-like structures, containing Mg 2+ and Al 3+, doped with Cr 3+ and Y 3+, have been prepared by precipitation at constant pH. The weight percentages of Cr 3+ and Y 3+ were 1, 2, or 3%, and 0.5 or 1%, respectively. Single phases were obtained in all cases, whose crystallinity decreased as the content in Cr and Y was increased. The solids have been characterised by element chemical analysis, powder X-ray diffraction, thermal analyses (differential, thermogravimetric and programmed reduction), FT-IR and UV-vis spectroscopies; the specific surface areas have been determined from nitrogen adsorption isotherms at -196 °C. Upon calcination at 1200 °C for 5 h in air all solids display a mixed structure (spinel and rock salt for MgO); these solids have also been characterised by these techniques and their chromatic coordinates (CIE - L∗a∗b∗) have been determined. Their pink colour makes these solids suitable for being used as ceramic pigments.

Fabrication of porous aluminium with directional pores through thermal decomposition method

International Nuclear Information System (INIS)

Nakajima, H; Kim, S Y; Park, J S

2009-01-01

Lotus-type porous metals were fabricated by unidirectional solidification in pressurized gas atmosphere. The elongated pres are evolved by insoluble gas resulted from the solubility gap between liquid and solid when the melt is solidified. Recently we developed a novel fabrication technique, in which gas compounds are used as a source of dissolving gas instead of the high pressure. In the present work this gas compound method was applied to fabrication of lotus aluminium. Hydrogen decomposed from calcium hydroxide, sodium bicarbonate and titanium hydride evolves cylindrical pores in aluminium. The porosity is about 20%. The pore size decreases and the pore number density increases with increasing amount of calcium hydroxide, which is explained by increase in pore nucleation sites.

Nickel-cobalt hydroxide nanosheets: Synthesis, morphology and electrochemical properties.

Science.gov (United States)

Schneiderová, Barbora; Demel, Jan; Zhigunov, Alexander; Bohuslav, Jan; Tarábková, Hana; Janda, Pavel; Lang, Kamil

2017-08-01

This paper reports the synthesis, characterization, and electrochemical performance of nickel-cobalt hydroxide nanosheets. The hydroxide nanosheets of approximately 0.7nm thickness were prepared by delamination of layered nickel-cobalt hydroxide lactate in water and formed transparent colloids that were stable for months. The nanosheets were deposited on highly oriented pyrolytic graphite by spin coating, and their electrochemical behavior was investigated by cyclic voltammetry in potassium hydroxide electrolyte. Our method of electrode preparation allows for studying the electrochemistry of nanosheets where the majority of the active centers can participate in the charge transfer reaction. The observed electrochemical response was ascribed to mutual compensation of the cobalt and nickel response via electron sharing between these metals in the hydroxide nanosheets, a process that differentiates the behavior of nickel-cobalt hydroxide nanosheets from single nickel hydroxide or cobalt hydroxide nanosheets or their physical mixture. The presence of cobalt in the nickel-cobalt hydroxide nanosheets apparently decreases the time of electrochemical activation of the nanosheet layer, which for the nickel hydroxide nanosheets alone requires more potential sweeps. Copyright © 2017 Elsevier Inc. All rights reserved.

Synthesis of calcium hydroxyapatite from calcium carbonate and different orthophosphate sources: A comparative study

International Nuclear Information System (INIS)

Pham Minh, Doan; Lyczko, Nathalie; Sebei, Haroun; Nzihou, Ange; Sharrock, Patrick

2012-01-01

Highlights: ► Calcium hydroxyapatite was synthesized from CaCO 3 and four orthophosphates. ► Only H 3 PO 4 led to the complete precipitation of orthophosphate species. ► H 3 PO 4 was also the most efficient for calcium dissolution. ► Reaction pathway was dissolution-precipitation accompanied by agglomeration step. - Abstract: The synthesis of calcium hydroxyapatite (Ca-HA) starting from calcium carbonate and different orthophosphate sources, including orthophosphoric acid, potassium, sodium and ammonium dihydrogen orthophosphates, was investigated under ambient conditions. The reaction started with calcium carbonate dissolution in an acid medium, followed by rapid precipitation of calcium cations with orthophosphate species to form calcium phosphate based particles which were in the size range of 0.4–1 μm. These particles then agglomerated into much larger ones, up to 350 μm in diameter (aggregates). These aggregates possessed an unstable porous structure which was responsible for the porosity of the final products. The highest specific surface area and pore volume were obtained with potassium dihydrogen orthophosphate. On the other hand, orthophosphoric acid led to the highest dissolution of calcium carbonate and the complete precipitation of orthophosphate species. Under ambient conditions, calcium phosphate based solid products of low crystallinity were formed. Different intermediates were identified and a reaction pathway proposed.

Preparation of magnesium hydroxide nanoflowers from boron mud via anti-drop precipitation method

Energy Technology Data Exchange (ETDEWEB)

Ma, Xi [School of Materials Science and Technology, China University of Geosciences, Beijing 100083 (China); Blue Sky Technology Corporation, Beijing 100083 (China); Ma, Hongwen, E-mail: mahw@cugb.edu.cn [School of Materials Science and Technology, China University of Geosciences, Beijing 100083 (China); Jiang, Xiaoqian [School of Materials Science and Technology, China University of Geosciences, Beijing 100083 (China); Jiang, Zhouqing [School of Materials Science and Technology, China University of Geosciences, Beijing 100083 (China); Blue Sky Technology Corporation, Beijing 100083 (China)

2014-08-15

Highlights: • We use the anti-drop precipitation method for synthesis of magnesium hydroxide. • Boron mud which is solid waste from a borax factory is used as the magnesium source. • The magnesium hydroxide nanoflowers are prepared in a short time. • The as-prepared magnesium hydroxide can be used as an effective flame retardant. - Abstract: Using boron mud as the starting material, the flower-like magnesium hydroxide (MH) has been successfully prepared via anti-drop precipitation method. The effect of NH{sub 3}·H{sub 2}O concentration, aging time, and surfactant on the morphology of MH was investigated. The optimum precipitation conditions are dropping MgSO{sub 4} solution in 5% NH{sub 3}·H{sub 2}O solution, with 3% polyethylene glycol as surfactant, aging for 30 min. XRD, SEM, FI-IR, and TG/DTA have been employed to characterize the as-prepared samples. XRD reveals that MH with high purity has the brucite structure. SEM images show that the flower-like MH exists in the form of mono-disperse well uniform spherical aggregation with diameter of 3–5 μm. TG/DTA shows a total percentage of weight loss 33.6% with a well-defined endothermic peak near 381.3 °C corresponding to the decomposition of MH. Furthermore, it reports that the extremely fast primary nucleation is of significance for crystal growth of MH.

21 CFR 73.2326 - Chromium hydroxide green.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Chromium hydroxide green. 73.2326 Section 73.2326... COLOR ADDITIVES EXEMPT FROM CERTIFICATION Cosmetics § 73.2326 Chromium hydroxide green. (a) Identity and specifications.The color additive chromium hydroxide green shall conform in identity and specifications to the...

Antibacterial effect of calcium hydroxide combined with chlorhexidine on Enterococcus faecalis: a systematic review and meta-analysis

Directory of Open Access Journals (Sweden)

Masoud SAATCHI

2014-10-01

Full Text Available Objective: Enterococcus faecalis (E. faecalis is the most frequently isolated strain in failed endodontic therapy cases since it is resistant to calcium hydroxide (CH. Whether a combination of CH and chlorhexidine (CHX is more effective than CH alone against E. faecalis is a matter of controversy. Thus, the aim of this study was to conduct a systematic review and meta-analysis of the literature. Material and Methods: A comprehensive search in PubMed, EMbase, EBSCOhost, The Cochrane Library, SciELO, and BBO databases, Clinical trials registers, Open Grey, and conference proceedings from the earliest available date to February 1, 2013 was carried out and the relevant articles were identified by two independent reviewers. Backward and forward search was performed and then inclusion and exclusion criteria were applied. The included studies were divided into "comparisons" according to the depth of sampling and dressing period of each medicament. Meta-analysis was performed using Stata software 10.0. The level of significance was set at 0.05. Results: Eighty-five studies were retrieved from databases and backward/forward searches. Fortyfive studies were considered as relevant (5 in vivo, 18 in vitro, 18 ex vivo, and 4 review articles. Nine studies were included for meta-analysis. Inter-observer agreement (Cohen kappa was 0.93. The included studies were divided into 21 comparisons for meta-analysis. Chi-square test showed the comparisons were heterogeneous (p<0.001. Random effect model demonstrated no significant difference between CH/CHX mixture and CH alone in their effect on E. faecalis (p=0.115. Conclusions: According to the evidence available now, mixing CH with CHX does not significantly increase the antimicrobial activity of CH against E. faecalis. It appears that mixing CH with CHX does not improve its ex vivo antibacterial property as an intracanal medicament against E. faecalis. Further in vivo studies are necessary to confirm and correlate

Antibacterial effect of calcium hydroxide combined with chlorhexidine on Enterococcus faecalis: a systematic review and meta-analysis

Science.gov (United States)

SAATCHI, Masoud; SHOKRANEH, Ali; NAVAEI, Hooman; MARACY, Mohammad Reza; SHOJAEI, Hasan

2014-01-01

Objective Enterococcus faecalis (E. faecalis) is the most frequently isolated strain in failed endodontic therapy cases since it is resistant to calcium hydroxide (CH). Whether a combination of CH and chlorhexidine (CHX) is more effective than CH alone against E. faecalis is a matter of controversy. Thus, the aim of this study was to conduct a systematic review and meta-analysis of the literature. Material and Methods A comprehensive search in PubMed, EMbase, EBSCOhost, The Cochrane Library, SciELO, and BBO databases, Clinical trials registers, Open Grey, and conference proceedings from the earliest available date to February 1, 2013 was carried out and the relevant articles were identified by two independent reviewers. Backward and forward search was performed and then inclusion and exclusion criteria were applied. The included studies were divided into "comparisons" according to the depth of sampling and dressing period of each medicament. Meta-analysis was performed using Stata software 10.0. The level of significance was set at 0.05. Results Eighty-five studies were retrieved from databases and backward/forward searches. Fortyfive studies were considered as relevant (5 in vivo, 18 in vitro, 18 ex vivo, and 4 review articles). Nine studies were included for meta-analysis. Inter-observer agreement (Cohen kappa) was 0.93. The included studies were divided into 21 comparisons for meta-analysis. Chi-square test showed the comparisons were heterogeneous (p<0.001). Random effect model demonstrated no significant difference between CH/CHX mixture and CH alone in their effect on E. faecalis (p=0.115). Conclusions According to the evidence available now, mixing CH with CHX does not significantly increase the antimicrobial activity of CH against E. faecalis. It appears that mixing CH with CHX does not improve its ex vivo antibacterial property as an intracanal medicament against E. faecalis. Further in vivo studies are necessary to confirm and correlate the findings of

Novel understanding of calcium silicate hydrate from dilute hydration

KAUST Repository

Zhang, Lina

2017-05-13

The perspective of calcium silicate hydrate (C-S-H) is still confronting various debates due to its intrinsic complicated structure and properties after decades of studies. In this study, hydration at dilute suspension of w/s equaling to 10 was conducted for tricalcium silicate (C3S) to interpret long-term hydration process and investigate the formation, structure and properties of C-S-H. Based on results from XRD, IR, SEM, NMR and so forth, loose and dense clusters of C-S-H with analogous C/S ratio were obtained along with the corresponding chemical formulae proposed as Ca5Si4O13∙6.2H2O. Crystalline structure inside C-S-H was observed by TEM, which was allocated at the foil-like proportion as well as the edge of wrinkles of the product. The long-term hydration process of C3S in dilute suspension could be sketchily described as migration of calcium hydroxide and in-situ growth of C-S-H with equilibrium silicon in aqueous solution relatively constant and calcium varied.

21 CFR 73.1326 - Chromium hydroxide green.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Chromium hydroxide green. 73.1326 Section 73.1326... COLOR ADDITIVES EXEMPT FROM CERTIFICATION Drugs § 73.1326 Chromium hydroxide green. (a) Identity. (1) The color additive chromium hydroxide green is principally hydrated chromic sesquioxide (Cr2O3·XH2O...

Preparation of an anionic azo pigment-pillared layered double hydroxide and the thermo- and photostability of the resulting intercalated material

Science.gov (United States)

Guo, Shengchang; Li, Dianqing; Zhang, Weifeng; Pu, Min; Evans, David G.; Duan, Xue

2004-12-01

A large anionic pigment has been intercalated into a layered double hydroxide (LDH) host by ion-exchange of an Mg/Al LDH-nitrate precursor with a solution of C.I. Pigment Red 48:2 (the calcium salt of 4-((5-chloro-4-methyl-2-sulfophenyl)azo)-3-hydroxy-2-naphthalene-carboxylic acid), in ethane-1,2-diol. After intercalation of the pigment, the interlayer distance in the LDH increases from 0.86 to 1.72 nm. Infrared spectra and TG-DTA curves reveal the presence of a complex system of supramolecular host-guest interactions. The UV-visible diffuse reflectance spectra of C.I. Pigment Red 48:2 show marked changes after heating at 200 °C and above, whereas there are no significant changes in the spectra of the intercalated pigment after heating at temperatures up to 300 °C, showing that the thermostability is markedly enhanced by intercalation in the LDH host. The pigment-intercalated LDHs exhibits much higher photostability to UV light than the pristine pigment, in the case of both the pure solids and their composites with polypropylene, as shown by measurement of CIE 1976 L*a*b* color difference ( ΔE) values.

Calcium modified edible Canna (Canna edulis L) starch for controlled released matrix

Science.gov (United States)

Putri, A. P.; Ridwan, M.; Darmawan, T. A.; Darusman, F.; Gadri, A.

2017-07-01

Canna edulis L starch was modified with calcium chloride in order to form controlled released matrix. Present study aim to analyze modified starch characteristic. Four different formulation of ondansetron granules was used to provide dissolution profile of controlled released, two formula consisted of 15% and 30% modified starch, one formula utilized matrix reference standards and the last granules was negative control. Methocel-hydroxypropyl methyl cellulose was used as controlled released matrix reference standards in the third formula. Calcium starch was synthesized in the presence of sodium hydroxide to form gelatinized mass and calcium chloride as the cross linking agent. Physicochemical and dissolution properties of modified starch for controlled released application were investigated. Modified starch has higher swelling index, water solubility and compressibility index. Three of four different formulation of granules provide dissolution profile of controlled released. The profiles indicate granules which employed calcium Canna edulis L starch as matrix are able to resemble controlled drug released profile of matrix reference, however their bigger detain ability lead to lower bioavailability.

Universal chemiluminescence flow-through device based on directed self-assembly of solid-state organic chromophores on layered double hydroxide matrix.

Science.gov (United States)

Wang, Zhihua; Teng, Xu; Lu, Chao

2013-02-19

In this work, a universal chemiluminescence (CL) flow-through device suitable for various CL resonance energy transfer (CRET) systems has been successfully fabricated. Highly efficient CRET in solid-state photoactive organic molecules can be achieved by assembling them on the surface of layered double hydroxides (LDHs). We attribute these observations to the suppression of the intermolecular π-π stacking interactions among aromatic rings and the improvement of molecular orientation and planarity in the LDH matrix, enabling a remarkable increase in fluorescence lifetime and quantum yield of organic molecules. Under optimal conditions, using peroxynitrous acid-fluorescein dianion (FLUD) as a model CRET system, trace FLUD (10 μM) was assembled on the surface of LDHs. Peroxynitrous acid/nitrite could be assayed in the range of 1.0-500 μM, and the detection limit for peroxynitrous acid/nitrite (S/N = 3) was 0.6 μM. This CL flow-through device exhibited operational stability, high reproducibility, and long lifetime. While LDHs were immobilized in a flow-through device in the absence of FLUD, the detection limit for peroxynitrous acid/nitrite was 100 μM. On the other hand, FLUD at the same concentration can not enhance the CL intensity of peroxynitrous acid system. This fabricated CL flow-through column has been successfully applied to determine nitrite in sausage samples with recoveries of 98-102%. These satisfactory results demonstrated that our studies pave a novel way toward flow-through column-based CRET using solid-state organic molecules as acceptors for signal amplification.

Management of Cyst-like Periapical Lesions by Orthograde Decompression and Long-term Calcium Hydroxide/Chlorhexidine Intracanal Dressing: A Case Series.

Science.gov (United States)

Santos Soares, Suelleng Maria Cunha; Brito-Júnior, Manoel; de Souza, Flávia Kelly; Zastrow, Eduardo Von; Cunha, Carla Oliveira da; Silveira, Frank Ferreira; Nunes, Eduardo; César, Carlos Augusto Santos; Glória, José Cristiano Ramos; Soares, Janir Alves

2016-07-01

Cyst-like periapical lesions should be treated initially with conservative nonsurgical procedures. In this case series, we describe the clinical and radiographic outcomes of large cyst-like lesions that were treated by orthograde decompression and long-term intracanal use of calcium hydroxide [Ca(OH)2] mixed with 2% chlorhexidine digluconate. Ten cases of cyst-like periapical lesions involving 15 teeth from 10 patients were selected. Maximal radiographic diameters of the lesions ranged from 11 to 28 mm. Nonsurgical procedures were performed, including apical patency, orthograde puncture of cyst-like exudates, chemomechanical preparation, and placement of intracanal Ca(OH)2/CHX dressings, which were periodically replaced during 6-10 months. The root canals were then filled with gutta-percha and sealer. The follow-up periods ranged from 6 to 24 months, and the outcome was classified as healed, healing, or failure. Nine lesions drained copious exudates after canal patency. One lesion only drained bloody serous exudate after periapical overinstrumentation. In 9 patients, intracanal exudation ceased in the first follow-up visit. At the 24-month follow-up, 6 lesions (60.0%) had healed, and 3 lesions (30.0%) were healing, with the corresponding patients being without clinical signs or symptoms. The case of treatment failure was submitted to surgical treatment. Microscopically, the lesion appeared to be an apical cyst with exuberant extraradicular bacterial biofilms attached to the sectioned root apex. This case series supports the use of nonsurgical methods to resolve larger cyst-like periapical lesions. Published by Elsevier Inc.

An in vitro comparison of irrigation using photon-initiated photoacoustic streaming, ultrasonic, sonic and needle techniques in removing calcium hydroxide.

Science.gov (United States)

Arslan, H; Akcay, M; Capar, I D; Saygili, G; Gok, T; Ertas, H

2015-03-01

To evaluate the effect of various techniques including photon-initiated photoacoustic streaming (PIPS), ultrasonic, sonic and needle irrigation on the removal of calcium hydroxide [Ca(OH)2 ] from artificial grooves created in root canals. The root canals of 48 extracted single-rooted teeth with straight canals were prepared using ProTaper rotary instruments up to size 40. After the specimens had been split longitudinally, a standardized groove was prepared in the apical part of one segment that was filled with Ca(OH)2 powder mixed with distilled water. Each tooth was reassembled and the apices closed with wax. The specimens were irrigated for 60 s with one of the following techniques: needle irrigation using 17% EDTA, PIPS with 17% EDTA, ultrasonic irrigation using 17% EDTA and sonic irrigation (EndoActivator) using 17% EDTA. The root segments were then disassembled, and the amount of remaining Ca(OH)2 evaluated under a stereomicroscope at 25× magnification. A pixel count of Ca(OH)2 remaining on the artificially created grooves was recorded as a percentage of the overall groove surface. The data were evaluated statistically using one-way analysis of variance and the least significant difference post hoc tests at 95% confidence level (P = 0.05). Photon-initiated photoacoustic streaming was superior in removing Ca(OH)2 as compared to needle irrigation (P streaming provided complete removal of Ca(OH)2 from artificial grooves in straight root canals. Ultrasonic irrigation enhanced the Ca(OH)2 removal capacity of irrigating solution but did not provide complete removal from artificial grooves. © 2014 International Endodontic Journal. Published by John Wiley & Sons Ltd.

Physicochemical characterization of atorvastatin calcium/ezetimibe amorphous nano-solid dispersions prepared by electrospraying method.

Science.gov (United States)

Jahangiri, Azin; Barzegar-Jalali, Mohammad; Javadzadeh, Yousef; Hamishehkar, Hamed; Adibkia, Khosro

2017-09-01

In the present study, electrospraying was applied as a novel method for the fabrication of amorphous nano-solid dispersions (N-SDs) of atorvastatin calcium (ATV), ezetimibe (EZT), and ATV/EZT combination as poorly water-soluble drugs. N-SDs were prepared using polyvinylpyrrolidone K30 as an amorphous carrier in 1:1 and 1:5 drug to polymer ratios and the total solid (including drug and polymer) concentrations of 10 and 20% (w/v). The prepared formulations were further investigated for their morphological, physicochemical, and dissolution properties. Scanning electron microscopy studies indicated that the morphology and diameter of the electrosprayed samples (ESs) were influenced by the solution concentration and drug:polymer ratio, so that an increase in the solution concentration resulted in fiber formation while an increase in the polymer ratio led to enhancement of the particle diameter. Differential scanning calorimetry and X-ray powder diffraction studies together with in vitro dissolution test revealed that the ESs were present in an amorphous form with improved dissolution properties. Infrared spectroscopic studies showed hydrogen-bonding interaction between the drug and polymer in ESs. Since the electrospraying method benefits from the both amorphization and nanosizing effect, this novel approach seems to be an efficient method for the fabrication of N-SDs of poorly water-soluble drugs.

Evaluation of a consolidation treatment in dolostones by mean of calcium hydroxide nanoparticles in high relative humidity conditions; Evaluacion del tratamiento de consolidacion de dolomias mediante nanoparticulas de hidroxido de calcio en condiciones de alta humedad relativa

Energy Technology Data Exchange (ETDEWEB)

Gomez-Villalba, L. s.; Lopez-Arce, P.; Zornoza, A.; Alvares de Buergo, M.; Fort, R.

2011-07-01

In this article, the results of a treatment applied to dolomitic stones using an isopropyl colloidal solution based on calcium hydroxide nanoparticles with a concentration of 2.0g/l are presented. The consolidation process in the stone has been checked before and after 28 days of exposure to 75% relative humidity. Morphologic and structural studies of the consolidating product confirmed the carbonation process. X ray diffraction, electron microscopy (TEM and ESEM), and electron diffraction carried out on the consolidating product have confirmed the transformation of portlandite phase to calcium carbonate polymorph, calcite, aragonite and vaterite. Petrophysical tests performed on the stone before and after the application of the product have shown the improvement in the physical and hydrical properties due to the increase in the ultrasound velocity and density of the material, and a decrease in the capillarity coefficient and open porosity without significant changes in colour and brightness. The application of the consolidating product in the proposed experimental conditions is a natural method, compatible with the petrological characteristics of the substrate, without secondary damages on the stone, being an effective method to improve the durability of carbonate stones. (Author) 26 refs.

Calcium silicate-based sealers: Assessment of physicochemical properties, porosity and hydration.

Science.gov (United States)

Marciano, Marina Angélica; Duarte, Marco Antonio Hungaro; Camilleri, Josette

2016-02-01

Investigation of hydration, chemical, physical properties and porosity of experimental calcium silicate-based sealers. Experimental calcium silicate-based sealers with calcium tungstate and zirconium oxide radio-opacifiers were prepared by mixing 1g of powder to 0.3 mL of 80% distilled water and 20% propylene glycol. MTA and MTA Fillapex were used as controls. The raw materials and set sealers were characterized using a combination of scanning electron microscopy, energy dispersive spectroscopy and X-ray diffraction. Physical properties were analyzed according to ANSI/ADA. The pH and calcium ion release were assessed after 3, 24, 72 and 168 h. The porosity was assessed using mercury intrusion porosimetry. The analysis of hydration of prototype sealers revealed calcium hydroxide as a by-product resulting in alkaline pH and detection of calcium ion release, with high values in initial periods. The radiopacity was similar to MTA for the sealers containing high amounts of radio-opacifiers (p>0.05). Flowability was higher and film thickness was lower for resinous MTA Fillapex sealer (p0.05). The prototype sealers presented adequate hydration, elevated pH and calcium ion release. Regarding physical properties, elevated proportions of radio-opacifiers were necessary to accomplish adequate radiopacity, enhance flowability and reduce film thickness. All the tested sealers presented water sorption and porosity similar to MTA. Copyright © 2015 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Kinetics and Mechanism of Calcium Hydroxide Conversion into Calcium Alkoxides: Implications in Heritage Conservation Using Nanolimes.

Science.gov (United States)

Rodriguez-Navarro, Carlos; Vettori, Irene; Ruiz-Agudo, Encarnacion

2016-05-24

Nanolimes are alcohol dispersions of Ca(OH)2 nanoparticles used in the conservation of cultural heritage. Although it was believed that Ca(OH)2 particles were inert when dispersed in short-chain alcohols, it has been recently shown that they can undergo transformation into calcium alkoxides. Little is known, however, about the mechanism and kinetics of such a phase transformation as well as its effect on the performance of nanolimes. Here we show that Ca(OH)2 particles formed after lime slaking react with ethanol and isopropanol and partially transform (fractional conversion, α up to 0.08) into calcium ethoxide and isopropoxide, respectively. The transformation shows Arrhenius behavior, with apparent activation energy Ea of 29 ± 4 and 37 ± 6 kJ mol(-1) for Ca-ethoxide and Ca-isopropoxide conversion, respectively. High resolution transmission electron microscopy analyses of reactant and product phases show that the alkoxides replace the crystalline structure of Ca(OH)2 along specific [hkl] directions, preserving the external hexagonal (platelike) morphology of the parent phase. Textural and kinetic results reveal that this pseudomorphic replacement involves a 3D diffusion-controlled deceleratory advancement of the reaction front. The results are consistent with an interface-coupled dissolution-precipitation replacement mechanism. Analysis of the carbonation of Ca(OH)2 particles with different degree of conversion into Ca-ethoxide (α up to 0.08) and Ca-isopropoxide (α up to 0.04) exposed to air (20 °C, 80% relative humidity) reveals that Ca-alkoxides significantly reduce the rate of transformation into cementing CaCO3 and induce the formation of metastable vaterite, as opposed to stable calcite which forms in untransformed Ca(OH)2 samples. Similar effects are obtained when a commercial nanolime partially transformed into Ca-ethoxide is subjected to carbonation. Such effects may hamper/delay the strengthening or consolidation effects of nanolimes, thus having

Rapid Synthesis of Lead Oxide Nanorods by One-step Solid-state Chemical Reaction at Room Temperature

Institute of Scientific and Technical Information of China (English)

CAO, Ya-Li(曹亚丽); JIA, Dian-Zeng(贾殿赠); LIU, Lang(刘浪); LUO, Jian-Min(骆建敏)

2004-01-01

A simple and facile method was reported to synthesize lead oxide nanorods. Nanorods of lead oxide were obtained directly from grinding solid metal salt and sodium hydroxide in agate mortar with the assistance of a suitable nonionic surfactant in only one step, which is different from the result of hydroxide in solution. The product has been characterized by XRD, TEM and SEM. The formation mechanism of rod-like morphology is discussed and the surfactant plays an important soft-template role in modifying the interface of solid-state reaction and according process of rod-formation.

21 CFR 73.1010 - Alumina (dried aluminum hydroxide).

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Alumina (dried aluminum hydroxide). 73.1010... GENERAL LISTING OF COLOR ADDITIVES EXEMPT FROM CERTIFICATION Drugs § 73.1010 Alumina (dried aluminum hydroxide). (a) Identity. (1) The color additive alumina (dried aluminum hydroxide) is a white, odorless...

Oxidation of Dodecanoate Intercalated Iron(II)–Iron(III) Layered Double Hydroxide to Form 2D Iron(III) (Hydr)oxide Layers

DEFF Research Database (Denmark)

Huang, Li‐Zhi; Ayala‐Luis, Karina B.; Fang, Liping

2013-01-01

hydroxide planar layer were preserved during the oxidation, as shown by FTIR spectroscopy. The high positive charge in the hydroxide layer produced by the oxidation of iron(II) to iron(III) is partially compensated by the deprotonation of hydroxy groups, as shown by X‐ray photoelectron spectroscopy...... between the alkyl chains of the intercalated dodecanoate anions play a crucial role in stabilizing the structure and hindering the collapse of the iron(II)–iron(III) (hydr)oxide structure during oxidation. This is the first report describing the formation of a stable planar layered octahedral iron......(III) (hydr)oxide. oxGRC12 shows promise as a sorbent and host for hydrophobic reagents, and as a possible source of single planar layers of iron(III) (hydr)oxide....

Time-dependent antibacterial effects of Aloe vera and Zataria multiflora plant essential oils compared to calcium hydroxide in teeth infected with Enterococcus faecalis.

Science.gov (United States)

Abbaszadegan, Abbas; Sahebi, Safoora; Gholami, Ahmad; Delroba, Alireza; Kiani, Amin; Iraji, Aida; Abbott, Paul Vincent

2016-02-01

In the present in vitro study, we investigated the time-related antimicrobial efficacy of Aloe vera and Zataria multiflora (Z. multiflora) plant essential oils compared to calcium hydroxide ([Ca[OH]2 ) to eliminate Enterococcus faecalis (E. faecalis) from root canals. A new strain of E. faecalis (Enterococcus spp. AGH04) was isolated from a previously root-filled tooth with persistent apical periodontitis. The 16S rRNA sequence was analyzed and deposited in GeneBank under accession number KF465681. A total of 108 extracted human single-rooted teeth were contaminated with this bacterial strain and treated with Aloe vera essential oil, Z. multiflora essential oil, and Ca(OH)2 for 1, 7, and 14 days. Gas chromatography-mass spectrometry (GC-MS) was used to determine the chemical composition of the oils. The percentage reduction from initial c.f.u./mL counts were calculated and analyzed. Carvacrol, thymol, and linalool were the main constituents of both essential oils. The c.f.u./mL count reductions significantly increased for all three medicaments when the contact time was extended. A statistically-significant difference was observed between the medicaments after 1 and 7 days, but there was no significant difference after 14 days. Both medicinal herbs showed equal antimicrobial efficiency against E. faecalis, comparable to Ca(OH)2 for the prolonged contact time of 14 days. © 2014 Wiley Publishing Asia Pty Ltd.

Interaction of radium with fresh water sediments and their mineral components Pt. 1. Ferris hydroxide and quartz

Energy Technology Data Exchange (ETDEWEB)

Benes, P; Strejc, P; Lukavec, Z [Ceske Vysoke Uceni Technicke, Prague (Czechoslovakia). Katedra Jaderne Chemie

1984-05-01

The radiotracer method has been used for investigation of the adsorption and desorption of radium traces on ferric hydroxide and quartz under conditions similar to those prevailing in waste and surface waters. The effects of pH, liquid to solid ratio, ionic strength and presence of Ca/sup 2 +/ or SO/sub 4//sup 2 -/ ions have been studied. It is concluded that at pH less than 7 and at concentration of suspended sediments of common composition less than 100 mg.1/sup -1/, ferric hydroxide and quartz have negligible effect on the state and migration of radium in surface waters. Radium adsorbed on quartz can be easily desorbed with dilute solutions of hydrochloric acid or sodium chloride. 14 refs.

Pore size distribution, strength, and microstructure of portland cement paste containing metal hydroxide waste

Energy Technology Data Exchange (ETDEWEB)

Majid, Z.A.; Mahmud, H.; Shaaban, M.G.

1996-12-31

Stabilization/solidification of hazardous wastes is used to convert hazardous metal hydroxide waste sludge into a solid mass with better handling properties. This study investigated the pore size development of ordinary portland cement pastes containing metal hydroxide waste sludge and rice husk ash using mercury intrusion porosimetry. The effects of acre and the addition of rice husk ash on pore size development and strength were studied. It was found that the pore structures of mixes changed significantly with curing acre. The pore size shifted from 1,204 to 324 {angstrom} for 3-day old cement paste, and from 956 to 263 {angstrom} for a 7-day old sample. A reduction in pore size distribution for different curing ages was also observed in the other mixtures. From this limited study, no conclusion could be made as to any correlation between strength development and porosity. 10 refs., 6 figs., 3 tabs.

Effects of soaking and acidification on physicochemical properties of calcium-fortified rice.

Science.gov (United States)

Sirisoontaralak, Porntip; Limboon, Pailin; Jatuwong, Sujitra; Chavanalikit, Arusa

2016-06-01

Calcium-fortified rice was prepared by soaking milled rice in calcium lactate solution, steaming and drying, and physicochemical properties were determined to evaluate effects of calcium concentration (0, 30, 50 g L(-1) ), soaking temperature (ambient temperature, 40 °C, 60 °C) and acidification. Calcium-fortified rice had less lightness. More total solid loss was observed, especially at high soaking temperature. Harder texture was detected with increased calcium concentration. Calcium fortification lowered pasting viscosity of milled rice. Panelists accepted all fortified rice; however, only rice soaked at 50 g L(-1) concentration could be claimed as a good source of calcium. Increasing of soaking temperature induced more penetration of calcium to rice kernels but calcium was lost more easily after washing. With addition of acetic acid to the soaking solution, enriched calcium content was comparable to that of high soaking temperature but with better retention after washing and calcium solubility was improved. Acid induced reduction of lightness and cooked rice hardness but increased total solid loss and pasting viscosity. Although the taste of acetic acid remained, panelists still accepted the fortified rice. Calcium-fortified rice (190.47-194.3 mg 100 g(-1) ) could be successfully produced by soaking milled rice in 50 g L(-1) calcium lactate solution at 40 °C or at ambient temperature with acidification. © 2015 Society of Chemical Industry. © 2015 Society of Chemical Industry.

Comparison between one-session root canal treatment with aPDT and two-session treatment with calcium hydroxide-based antibacterial dressing, in dog's teeth with apical periodontitis.

Science.gov (United States)

Hidalgo, Lidia Regina da Costa; da Silva, Léa Assed Bezerra; Nelson-Filho, Paulo; da Silva, Raquel Assed Bezerra; de Carvalho, Fabrício Kitazono; Lucisano, Marília Pacífico; Novaes, Arthur Belem

2016-09-01

To evaluate one-session endodontic treatment with aPDT and two-session treatment with calcium hydroxide (CH)-based dressing in dog's teeth with apical periodontitis. After experimental induction of apical periodontitis, 48 teeth were randomly assigned to the following groups: groups OS/aPDT120d and OS/aPDT180d (one-session treatment with aPDT) and groups TS/CH120d and TS/CH180d (two-session treatment with CH-based dressing-control groups). The animals were euthanized after 120 and 180 days. After histotechnical processing, microscopic and radiographic analyses were performed. Data were analyzed by Kruskal-Wallis and Fisher's exact tests (α = 0.05). Groups TS/CHs presented repaired resorbed cemental areas, with collagen bundles and few inflammatory cells. In groups OS/aPDTs, the areas of cemental resorption were not repaired with reduced presence of cells and fibers. In the analysis of the apical closure, fluorescence microscopy and percentage of radiographic reduction of lesions, there was significant difference between groups TS/CH120d and OS/aPDT120d and between TS/CH180d and OS/aPDT180d (p session endodontic treatment using a CH-based dressing in teeth with apical periodontitis.

Hydrothermal crystallization of zirconia and zirconia solid solutions

International Nuclear Information System (INIS)

Pyda, W.; Haberko, K.; Bucko, M.M.

1991-01-01

Zirconia as well as yttria-zirconia and calcia-zirconia solid-solution powders were crystallized under hydrothermal conditions from (co)precipitated hydroxides. The morphology of the power particles is strongly dependent on the crystallization conditions. The powders crystallized in a water solution of Na, K, and Li hydroxides show elongated particles of much larger sizes than those which result from the process carried out in pure water or a water solution of Na, K, or Li chlorides. The shapes of the latter particles are isometric. In this paper the growth mechanism of the elongated particles is suggested

Efficacy of sonic and ultrasonic activation for removal of calcium hydroxide from mesial canals of mandibular molars: a microtomographic study.

Science.gov (United States)

Wiseman, Anne; Cox, Timothy C; Paranjpe, Avina; Flake, Natasha M; Cohenca, Nestor; Johnson, James D

2011-02-01

The purpose of this study was to use micro-computed tomography (micro-CT) scanning to evaluate the efficacy of sonic and passive ultrasonic irrigation (PUI) on calcium hydroxide (Ca[OH](2)) removal and to measure the volume and percentage of Ca(OH)(2) remaining in the root canal system. The root canals of 46 extracted human mandibular molar teeth were prepared with rotary instruments and randomly assigned to two experimental groups (n = 40) as well as positive and negative controls (n = 6). In each experimental group, 20 teeth were assigned to each irrigation protocol, sonic or passive ultrasonic irrigation. All experimental teeth and the positive controls were filled with Ca(OH)(2), whereas the negative control teeth did not receive Ca(OH)(2). All teeth were scanned using micro-CT scanning to determine the dressing volume. After 7 days, the Ca(OH)(2) was removed in the experimental groups using rotary instrumentation only, and the teeth were again scanned using micro-CT scanning to calculate volume and percentage of Ca(OH)(2) removed. Positive control teeth were not subjected to rotary instrumentation. Experimental samples were then irrigated using either sonic or passive ultrasonic and the volume of remaining Ca(OH)(2) was calculated using micro-CT. Remnants of Ca(OH)(2) were found in all experimental groups. No Ca(OH)(2) was found in the negative controls, whereas a mean of 8.7 mm(3) of Ca(OH)(2) was recorded in the positive controls. Rotary plus passive ultrasonic irrigation removed significantly more Ca(OH)(2) (85.7%) than rotary plus sonic irrigation (71.5%) (p < 0.001). The combination of rotary instrumentation and passive ultrasonic activation for 3 periods of 20 seconds results in significantly lower amounts of Ca(OH)(2) remnants in the canal compared with sonic irrigation. Copyright © 2011. Published by Elsevier Inc.

Nucleation and growth kinetics of zirconium hydroxide by precipitation with ammonium hydroxide

International Nuclear Information System (INIS)

Carleson, T.E.; Chipman, N.A.

1987-01-01

The results of a study of the nucleation and growth kinetics of the precipitation of zirconium hydroxide from the reaction of hexafluorozirconate solution with ammonium hydroxide are reported. The McCabe linear growth rate model was used to correlate the results. The growth rate decreased with residence time and supersaturation for studies with 7 residence times (3.5 - 90 minutes and two supersaturation ratios (0.03 - 0.04, and 0.4). The nucleation rate increased with residence time and supersaturation. A negative kinetic order of nucleation was observed that may be due to the inhibition of particle growth by adsorption of reacting species on the crystal surfaces

Effect of Calcium Ions on the Disintegration of Enteric-Coated Solid Dosage Forms.

Science.gov (United States)

Al-Gousous, Jozef; Langguth, Peter

2016-02-01

To investigate the effect of calcium ions on the disintegration of enteric-coated dosage forms, disintegration testing was performed on enteric-coated aspirin tablets in the presence and absence of calcium in the test media. The results show that the presence of calcium ions retards the disintegration of enteric-coated dosage forms. This finding, which has not been reported in scientific literature, sheds light on the importance of conducting well-designed detailed investigations into the potential of calcium from dietary sources, calcium supplements, antacids, and/or phosphate binders affecting the absorption of drugs formulated into enteric-coated dosage forms. Moreover, it shows the necessity to investigate the potential of the occurrence of additional nutrient-excipient interactions. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Modification of Alumina and Spinel Inclusions by Calcium in Liquid Steel

Science.gov (United States)

Verma, Neerav

2011-12-01

Steel Cleanliness plays a crucial role in determining steel properties such as toughness, ductility, formability, corrosion resistance and surface quality. The production of clean steel often involves the elimination or chemical and morphological modification of oxide and sulfide inclusions. Along with deteriorating the steel properties, solid inclusions can affect steel castability through nozzle clogging. Nozzle clogging occurs when solid inclusions accumulate in the caster pouring system such as the ladle shroud or submerged entry nozzle (SEN). Thus, it is important to understand how to achieve desired inclusion characteristics (shape, size and chemistry) through the steelmaking process. Among the various practices adopted in industries to counteract the effect of solid inclusions, modification of solid inclusions to liquid or partially liquid state through calcium treatment is one of the methods. Calcium can be used because it has a strong ability to form oxides and sulfides. In Al-killed steels, the most common inclusions are alumina (Al2O3) inclusions, which are solid at steelmaking temperatures. On calcium treatment, solid alumina inclusions are converted to calcium aluminates, which have liquidus temperatures lower than steelmaking temperature (1600°C) [14]. It has been found that alumina inclusions may contain some MgO and such inclusions are termed alumina magnesia spinels (Al2O3.xMgO) [18]. These spinels are more stable than alumina and it has been suggested that they might be more difficult to modify [18]. But, some authors have proposed that MgO can actually help in the liquefaction of inclusions, and have demonstrated successful modification of spinels by Ca treatment [20, 21]. In the present research, the mechanism of transformation of alumina and spinel inclusions upon calcium treatment was studied by characterizing transient evolution of inclusions. A vacuum induction was used for melting, making additions (Al, Al-Mg and CaSi2) and sampling. The

Comparative evaluation of antimicrobial action of MTA, calcium hydroxide and Portland cement Avaliação comparativa da ação antimicrobiana do MTA, hidróxido de cálcio e cimento Portland

Directory of Open Access Journals (Sweden)

Caroline Sousa Ribeiro

2006-10-01

Full Text Available The present study aimed to evaluate and compare the antimicrobial effect of MTA Dentsply, MTA Angelus, Calcium Hydroxide and Portland cement. Four reference bacterial strains were used: Pseudomonas aeruginosa, Escherichia coli, Bacteroides fragilis, and Enterococcus faecalis. Plates containing Mueller-Hinton agar supplemented with 5% sheep blood, hemin, and menadione were inoculated with the bacterial suspensions. Subsequently, wells were prepared and immediately filled with materials and incubated at 37ºC for 48 hours under anaerobic conditions, except P. aeruginosa. The diameters of inhibition zones were measured, and data analyzed using ANOVA and the Tukey test with 1% level of significance. MTA Dentsply, MTA Angelus and Portland cement inhibited the growth of P. aeruginosa. Calcium Hydroxide was effective against P. aeruginosa and B. fragillis. Under anaerobic conditions, which may hamper the formation of reactive oxygen species, the materials failed to inhibit E. faecalis, and E. coli.O objetivo do presente trabalho foi avaliar e comparar o efeito antimicrobiano do MTA Dentsply, MTA Angelus, hidróxido de cálcio e cimento Portland sobre quatro cepas bacterianas: Pseudomonas aeruginosa, Escherichia coli, Bacteroides fragilis, e Enterococcus faecalis. Placas contendo agar Muller-Hinton suplementadas com 5% de sangue de carneiro, hemina e menadiona foram inoculadas com as suspensões bacterianas. Poços foram confeccionados com auxílio de perfuradores e imediatamente preenchidos com os materiais, e incubados a 37ºC por 48 horas em atmosfera de anaerobiose, exceto P. aeruginosa. O diâmetro dos halos de inibição foi medido e os dados analisados usando o teste estatístico ANOVA e o de Tukey com nível de significância de 1%. O MTA Dentsply, MTA Angelus e Cimento Portland inibiram o crescimento da P.aeruginosa. O hidróxido de cálcio foi efetivo contra P. aeruginosa e B. fragillis. Sob atmosfera de anaerobiose, condição que pode

Monitoring the progression of calcium and protein solubilisation as affected by calcium chelators during small-scale manufacture of casein-based food matrices.

Science.gov (United States)

McIntyre, Irene; O'Sullivan, Michael; O'Riordan, Dolores

2017-12-15

Calcium and protein solubilisation during small-scale manufacture of semi-solid casein-based food matrices was investigated and found to be very different in the presence or absence of calcium chelating salts. Calcium concentrations in the dispersed phase increased and calcium-ion activity (A Ca ++ ) decreased during manufacture of the matrices containing calcium chelating salts; with ∼23% of total calcium solubilised by the end of manufacture. In the absence of calcium chelating salts, these concentrations were significantly lower at equivalent processing times and remained unchanged as did A Ca ++ , throughout manufacture. The protein content of the dispersed phase was low (≤3% of total protein), but was significantly higher for matrices containing calcium chelating salts. This study elucidates the critical role of calcium chelating salts in modulating casein hydration and dispersion and gives an indication of the levels of soluble calcium and protein required to allow matrix formation during manufacture of casein-based food structures e.g. processed and analogue cheese. Copyright © 2017 Elsevier Ltd. All rights reserved.

Layered zinc hydroxide salts: Delamination, preferred orientation of hydroxide lamellae, and formation of ZnO nanodiscs

Czech Academy of Sciences Publication Activity Database

Demel, Jan; Pleštil, Josef; Bezdička, Petr; Janda, Pavel; Klementová, Mariana; Lang, Kamil

2011-01-01

Roč. 360, č. 2 (2011), s. 532-539 ISSN 0021-9797 R&D Projects: GA MŠk ME09058; GA ČR GAP207/10/1447 Institutional research plan: CEZ:AV0Z40320502; CEZ:AV0Z40500505; CEZ:AV0Z40400503 Keywords : layered zinc hydroxide * delamination * exfoliation * hydroxide layer * ZnO Subject RIV: CA - Inorganic Chemistry Impact factor: 3.070, year: 2011

CRACK2 - Modelling calcium carbonate deposition from bicarbonate solution in cracks in concrete

International Nuclear Information System (INIS)

Brodersen, K.

2003-03-01

The numerical CRACK2 model simulates precipitation of calcite from calcium bicarbonate solution (e.g. groundwater) passing through cracks in concrete or other cementitious materials. A summary of experimental work is followed by a detailed description of the model. Hydroxyl ions are transported by diffusion in pore systems in columns of cementitious materials. The hydroxyl is precipitating calcite from a flow of bicarbonate solution in a crack connecting the ends of a row of such columns. The cementitious material is simulated as calcium hydroxide mixed with inert material but with sodium hydroxide dissolved in the pore solution. Diffusive migration of cesium as radioactive isotope is also considered. Electrical interaction of the migrating ions is taken into account. Example calculations demonstrate effects of parameter variations on distribution of precipitated calcite in the crack and on the composition of the outflowing solution, which can be compared directly with experimental results. Leaching behavior of sodium can be used to tune the model to experimental observations. The calcite is mostly precipitated on top of the original crack surface and may under certain circumstances fill the crack. The produced thin layers of low porosity calcite act as a diffusion barrier limiting contact between cement and solution. Pore closure mechanisms in such layers are discussed. Implications for safety assessment of radioactive waste disposal are shortly mentioned. The model is also relevant for conventional uses of concrete. (au)

Polysulfide intercalated layered double hydroxides for metal capture applications

Energy Technology Data Exchange (ETDEWEB)

Kanatzidis, Mercouri G.; Ma, Shulan

2017-04-04

Polysulfide intercalated layered double hydroxides and methods for their use in vapor and liquid-phase metal capture applications are provided. The layered double hydroxides comprise a plurality of positively charged host layers of mixed metal hydroxides separated by interlayer spaces. Polysulfide anions are intercalated in the interlayer spaces.

Strategy for synthesizing quantum dot-layered double hydroxide nanocomposites and their enhanced photoluminescence and photostability.

Science.gov (United States)

Cho, Seungho; Jung, Sungwook; Jeong, Sanghwa; Bang, Jiwon; Park, Joonhyuck; Park, Youngrong; Kim, Sungjee

2013-01-08

Layered double hydroxide-quantum dot (LDH-QD) composites are synthesized via a room temperature LDH formation reaction in the presence of QDs. InP/ZnS (core/shell) QD, a heavy metal free QD, is used as a model constituent. Interactions between QDs (with negative zeta potentials), decorated with dihydrolipoic acids, and inherently positively charged metal hydroxide layers of LDH during the LDH formations are induced to form the LDH-QD composites. The formation of the LDH-QD composites affords significantly enhanced photoluminescence quantum yields and thermal- and photostabilities compared to their QD counterparts. In addition, the fluorescence from the solid LDH-QD composite preserved the initial optical properties of the QD colloid solution without noticeable deteriorations such as red-shift or deep trap emission. Based on their advantageous optical properties, we also demonstrate the pseudo white light emitting diode, down-converted by the LDH-QD composites.

Effects of mineral trioxide aggregate, BiodentineTM and calcium hydroxide on viability, proliferation, migration and differentiation of stem cells from human exfoliated deciduous teeth

Directory of Open Access Journals (Sweden)

Leandro Borges Araújo

2018-02-01

Full Text Available Abstract Objective: The aim of the study was to evaluate the effects of the capping materials mineral trioxide aggregate (MTA, calcium hydroxide (CH and BiodentineTM (BD on stem cells from human exfoliated deciduous teeth (SHED in vitro. Material and Methods: SHED were cultured for 1 – 7 days in medium conditioned by incubation with MTA, BD or CH (1 mg/mL, and tested for viability (MTT assay and proliferation (SRB assay. Also, the migration of serum-starved SHED towards conditioned media was assayed in companion plates, with 8 μm-pore-sized membranes, for 24 h. Gene expression of dentin matrix protein-1 (DMP-1 was evaluated by reverse-transcription polymerase chain reaction. Regular culture medium with 10% FBS (without conditioning and culture medium supplemented with 20% FBS were used as controls. Results: MTA, CH and BD conditioned media maintained cell viability and allowed continuous SHED proliferation, with CH conditioned medium causing the highest positive effect on proliferation at the end of the treatment period (compared with BD and MTA (p<0.05. In contrast, we observed increased SHED migration towards BD and MTA conditioned media (compared with CH (p<0.05. A greater amount of DMP-1 gene was expressed in MTA group compared with the other groups from day 7 up to day 21. Conclusion: Our results show that the three capping materials are biocompatible, maintain viability and stimulate proliferation, migration and differentiation in a key dental stem cell population.

Laboratory Synthesized Calcium Oxide and Calcium Hydroxide Grains: A Candidate to Explain the 6.8 Micron Band

Science.gov (United States)

Kimura, Yuki; Nuth, Joseph A., III

2005-01-01

We will demonstrate that CaO and Ca(OH)2 are excellent candidates to explain the 6.8 microns feature, which is one of the most obscure features in young stellar objects. We discuss the condensation of CaO grains and the potential formation of a Ca(OH)2 surface layer. The infrared spectra of these grains are compared with the spectra of fifteen young stellar objects. We note that CaO-rich grains are seen in all meteoritic CAIs (calcium-aluminum-rich inclusions) and the 6.8 micron feature has only been observed in young stellar objects. Therefore, we consider CaO grains to be a plausible candidate to explain the 6.8 microns feature and hypothesize that they are produced in the hot interiors of young stellar environments.

Solid-phase characterization in flammable-gas-tank sludges by electron microscopy

International Nuclear Information System (INIS)

Liu, J.; Pederson, L.R.; Qang, L.Q.

1995-09-01

The crystallinity, morphology, chemical composition, and crystalline phases of several Tank 241-SY-101 (hereinafter referred to as SY-101) and Tank 241-SY-103 (hereinafter referred to as SY-103) solid samples were studied by transmission electron microscopy (TEM), electron energy dispersive spectroscopy (EDS), and electron diffraction. The main focus is on the identification of aluminum hydroxide thought to be present in these tank samples. Aluminum hydroxide was found in SY-103, but not in SY-101. This difference can be explained by the different OH/Al ratios found in the two tank samples: a high OH/Al ratio in SY-101 favors the formation of sodium aluminate, but a low OH/Al ratio in SY-103 favors aluminum hydroxide. These results were confirmed by a magnetic resonance study on SY-101 and SY-103 simulant. The transition from aluminum hydroxide to sodium aluminate occurs at an OH/Al molar ratio of 3.6. It is believed that the study of Al(OH) 3 was not affected by sample preparation because all Al(OH) 3 is in the solid form according to the NMR experiments. There is no Al(OH) 3 in the liquid. It is, therefore, most likely that the observation of Al(OH) 3 is representative of the real sludge sample, and is not affected by drying. Similar conclusions also apply to other insoluble phases such as iron and chromium

Effects of chopping, and soaking in water, hydrochloric acidic and calcium hydroxide solutions on the nutritional value of Acacia villosa for goats

International Nuclear Information System (INIS)

Wina, E.; Tangendjaja, B.; Susana, I.W.R.

2005-01-01

Acacia villosa, a thornless shrub legume, has potential as a feed supplement for ruminants if anti-nutritional factors, especially tannins, can be overcome. The effects of chopping and soaking the leaves on the amounts of tannin in the extracting solution and that left in the recovered leaves were studied. The tannin and non-tannin phenolics were solubilized in the extracting solution and the amount was increased with the soaking time. Soaking in calcium hydroxide solution, hydrochloric acid or water removed 41-76% of tannin and total phenolics removed from the recovered leaves. Soaking of the leaves also removed fermentable materials and reduced the gas production. In the first of two digestibility experiments, three groups of goats received one of these diets, those were: (1) sugar cane tops: unsoaked Acacia leaves (7:3), (2) sugar cane tops: water soaked Acacia leaves (7:3) and (3) sugar cane tops: water soaked Acacia leaves (7:3) + 100 g/day of cassava flour. Live weight of goats was measured every 2 weeks and a large increase in average daily gain was obtained for goats fed diet containing water soaked leaves and cassava flour (71 g/day) compared to those fed diet containing unsoaked leaves and water soaked leaves (38.9 and 44.7 g/day, respectively) (P 0.05) found in intake or digestibility between unsoaked and soaked leaves. In conclusion, soaking reduced tannin in Acacia leaves, improved digestibility and intake of Acacia leaves. In the presence of cassava flour, soaking improved average daily gain. Diets supplemented with water soaked Acacia leaves probably also need an energy supplement and cassava flour is one of the feed ingredients that is satisfactory. (author)

Intercalation studies of zinc hydroxide chloride: Ammonia and amino acids

International Nuclear Information System (INIS)

Arízaga, Gregorio Guadalupe Carbajal

2012-01-01

Zinc hydroxide chloride (ZHC) is a layered hydroxide salt with formula Zn 5 (OH) 8 Cl 2 ·2H 2 O. It was tested as intercalation matrix for the first time and results were compared with intercalation products of the well-known zinc hydroxide nitrate and a Zn/Al layered double hydroxide. Ammonia was intercalated into ZHC, while no significant intercalation occurred in ZHN. Aspartic acid intercalation was only achieved by co-precipitation at pH=10 with ZHC and pH=8 with zinc hydroxide nitrate. Higher pH resistance in ZHC favored total deprotonation of both carboxylic groups of the Asp molecule. ZHC conferred more thermal protection against Asp combustion presenting exothermic peaks even at 452 °C while the exothermic event in ZHN was 366 °C and in the LDH at 276 °C. - Graphical abstract: The zinc hydroxide chloride (ZHC) with formula Zn 5 (OH) 8 Cl 2 ·2H 2 O was tested as intercalation matrix. In comparison with the well-known zinc hydroxide nitrate (ZHN) and layered double hydroxides (LDH), ZHC was the best matrix for thermal protection of Asp combustion, presenting exothermic peaks even at 452 °C, while the highest exothermic event in ZHN was at 366 °C, and in the LDH it was at 276 °C. Highlights: ► Zinc hydroxide chloride (ZHC) was tested as intercalation matrix for the first time. ► ZHC has higher chemical and thermal stability than zinc hydroxide nitrate and LDH. ► NH 3 molecules can be intercalated into ZHC. ► The amino group of amino acids limits the intercalation by ion-exchange.

Effects of Leaching Behavior of Calcium Ions on Compression and Durability of Cement-Based Materials with Mineral Admixtures

Science.gov (United States)

Cheng, An; Chao, Sao-Jeng; Lin, Wei-Ting

2013-01-01

Leaching of calcium ions increases the porosity of cement-based materials, consequently resulting in a negative effect on durability since it provides an entry for aggressive harmful ions, causing reinforcing steel corrosion. This study investigates the effects of leaching behavior of calcium ions on the compression and durability of cement-based materials. Since the parameters influencing the leaching behavior of cement-based materials are unclear and diverse, this paper focuses on the influence of added mineral admixtures (fly ash, slag and silica fume) on the leaching behavior of calcium ions regarding compression and durability of cemented-based materials. Ammonium nitrate solution was used to accelerate the leaching process in this study. Scanning electron microscopy, X-ray diffraction analysis, and thermogravimetric analysis were employed to analyze and compare the cement-based material compositions prior to and after calcium ion leaching. The experimental results show that the mineral admixtures reduce calcium hydroxide quantity and refine pore structure through pozzolanic reaction, thus enhancing the compressive strength and durability of cement-based materials. PMID:28809247

Investigation of Solid Dispersion of Atorvastatin Calcium in ...

African Journals Online (AJOL)

ATC), a poorly watersoluble 3-hydroxy 3-methyl glutaryl CoA (HMG-CoA) reductase inhibitor, by a solid dispersion technique using polyethylene glycol 6000 (PEG 6000) or polyvinylpyrrolidone k30 (PVP K30). Methods: The solid dispersions were ...

Inclusion of calcium hydroxide-treated corn stover as a partial forage replacement in diets for lactating dairy cows.

Science.gov (United States)

Casperson, Brittany A; Wertz-Lutz, Aimee E; Dunn, Jim L; Donkin, Shawn S

2018-03-01

Chemical treatment may improve the nutritional value of corn crop residues, commonly referred to as corn stover, and the potential use of this feed resource for ruminants, including lactating dairy cows. The objective of this study was to determine the effect of prestorage chopping, hydration, and treatment of corn stover with Ca(OH) 2 on the feeding value for milk production, milk composition, and dry matter intake (DMI). Multiparous mid-lactation Holstein cows (n = 30) were stratified by parity and milk production and randomly assigned to 1 of 3 diets. Corn stover was chopped, hydrated, and treated with 6% Ca(OH) 2 (as-fed basis) and stored in horizontal silo bags. Cows received a control (CON) total mixed ration (TMR) or a TMR in which a mixture of treated corn stover and distillers grains replaced either alfalfa haylage (AHsub) or alfalfa haylage and an additional portion of corn silage (AH+CSsub). Treated corn stover was fed in a TMR at 0, 15, and 30% of the diet DM for the CON, AHsub, and AH+CSsub diets, respectively. Cows were individually fed in tiestalls for 10 wk. Milk production was not altered by treatment. Compared with the CON diet, DMI was reduced when the AHsub diet was fed and tended to be reduced when cows were fed the AH+CSsub diet (25.9, 22.7, and 23.1 ± 0.88 kg/d for CON, AHsub, and AH+CSsub diets, respectively). Energy-corrected milk production per unit of DMI (kg/kg) tended to increase with treated corn stover feeding. Milk composition, energy-corrected milk production, and energy-corrected milk per unit of DMI (kg/kg) were not different among treatments for the 10-wk feeding period. Cows fed the AHsub and AH+CSsub diets had consistent DMI over the 10-wk treatment period, whereas DMI for cows fed the CON diet increased slightly over time. Milk production was not affected by the duration of feeding. These data indicate that corn stover processing, prestorage hydration, and treatment with calcium hydroxide can serve as an alternative to

Preparation, physical-chemical characterisation and cytocompatibility of calcium carbonate cements.

Science.gov (United States)

Combes, C; Miao, Baoji; Bareille, Reine; Rey, Christian

2006-03-01

The feasibility of calcium carbonate cements involving the recrystallisation of metastable calcium carbonate varieties has been demonstrated. Calcium carbonate cement compositions presented in this paper can be prepared straightforwardly by simply mixing water (liquid phase) with two calcium carbonate phases (solid phase) which can be easily obtained by precipitation. An original cement composition was obtained by mixing amorphous calcium carbonate and vaterite with an aqueous medium. The cement set and hardened within 2h at 37 degrees C in an atmosphere saturated with water and the final composition of the cement consisted mostly of aragonite. The hardened cement was microporous and showed poor mechanical properties. Cytotoxicity tests revealed excellent cytocompatibility of calcium carbonate cement compositions. Calcium carbonates with a higher solubility than the apatite formed for most of the marketed calcium phosphate cements might be of interest to increase biomedical cement resorption rates and to favour its replacement by bone tissue.

Influence of carbonate intercalation in the surface-charging behavior of Zn-Cr layered double hydroxides

International Nuclear Information System (INIS)

Rojas, R.; Barriga, C.; De Pauli, C.P.; Avena, M.J.

2010-01-01

The influence of interlayer composition in the surface charge and reactivity of layered double hydroxides (LDHs) has been explored. With this purpose, a chloride-intercalated Zn-Cr-LDH has been synthesized by the constant pH coprecipitation method and afterwards exchanged with carbonate to obtain solids with different Cl - /CO 3 2- ratios. The solids structure has been characterized by elemental chemical analysis, powder X-ray diffraction and infrared spectroscopy, while its surface-charging behavior and reactivity have been studied by acid-base potentiometric titrations and electrophoretic mobility determinations. The chloride-intercalated sample shows an increasing hydroxyl adsorption with increasing pH and decreasing support electrolyte concentration and the particles present positive electrophoretic mobility in the measured pH range. As carbonate content increases in the samples, the total OH - uptake diminishes and the samples show an isoelectric point at pH around 10. When the gallery is totally occupied by carbonate anions, the OH uptake vs. pH curves registered at different electrolyte concentrations merge at around pH 10. A LDH-water interface model has been used to give an interpretation to the experimental data. The model indicates that as carbonate content increases, the sample behavior becomes similar to that of a metal (hydr)oxide and that surface (bi)carbonate anions undergo acid-base reactions.

Influence of carbonate intercalation in the surface-charging behavior of Zn-Cr layered double hydroxides

Energy Technology Data Exchange (ETDEWEB)

Rojas, R., E-mail: rrojas@mail.fcq.unc.edu.ar [INFIQC, Departamento de Fisicoquimica, Facultad de Ciencias Quimicas, Universidad Nacional de Cordoba, Ciudad Universitaria, 5000 Cordoba (Argentina); Barriga, C. [Departamento de Quimica Inorganica e Ingenieria Quimica, Edificio Marie Curie, Campus de Rabanales, Universidad de Cordoba, 14071 Cordoba (Spain); De Pauli, C.P. [INFIQC, Departamento de Fisicoquimica, Facultad de Ciencias Quimicas, Universidad Nacional de Cordoba, Ciudad Universitaria, 5000 Cordoba (Argentina); Avena, M.J. [Departamento de Quimica, Universidad Nacional del Sur, Avenida Alem 1253, 8000 Bahia Blanca (Argentina)

2010-01-15

The influence of interlayer composition in the surface charge and reactivity of layered double hydroxides (LDHs) has been explored. With this purpose, a chloride-intercalated Zn-Cr-LDH has been synthesized by the constant pH coprecipitation method and afterwards exchanged with carbonate to obtain solids with different Cl{sup -}/CO{sub 3}{sup 2-} ratios. The solids structure has been characterized by elemental chemical analysis, powder X-ray diffraction and infrared spectroscopy, while its surface-charging behavior and reactivity have been studied by acid-base potentiometric titrations and electrophoretic mobility determinations. The chloride-intercalated sample shows an increasing hydroxyl adsorption with increasing pH and decreasing support electrolyte concentration and the particles present positive electrophoretic mobility in the measured pH range. As carbonate content increases in the samples, the total OH{sup -} uptake diminishes and the samples show an isoelectric point at pH around 10. When the gallery is totally occupied by carbonate anions, the OH uptake vs. pH curves registered at different electrolyte concentrations merge at around pH 10. A LDH-water interface model has been used to give an interpretation to the experimental data. The model indicates that as carbonate content increases, the sample behavior becomes similar to that of a metal (hydr)oxide and that surface (bi)carbonate anions undergo acid-base reactions.

Ion Implantation of Calcium and Zinc in Magnesium for Biodegradable Implant Applications

Directory of Open Access Journals (Sweden)

Sahadev Somasundaram

2018-01-01

Full Text Available In this study, magnesium was implanted with calcium-ion and zinc-ion at fluences of 1015, 1016, and 1017 ion·cm−2, and its in vitro degradation behaviour was evaluated using electrochemical techniques in simulated body fluid (SBF. Rutherford backscattering spectrometry (RBS revealed that the implanted ions formed layers within the passive magnesium-oxide/hydroxide layers. Electrochemical impedance spectroscopy (EIS results demonstrated that calcium-ion implantation at a fluence of 1015 ions·cm−2 increased the polarisation resistance by 24%, but higher fluences showed no appreciable improvement. In the case of zinc-ion implantation, increase in the fluence decreased the polarisation resistance. A fluence of 1017 ion·cm−2 decreased the polarisation resistance by 65%, and fluences of 1015 and 1016 showed only marginal effect. Similarly, potentiodynamic polarisation results also suggested that low fluence of calcium-ion decreased the degradation rate by 38% and high fluence of zinc-ion increased the degradation rate by 61%. All the post-polarized ion-implanted samples and the bare metal revealed phosphate and carbonate formation. However, the improved degradative behaviour in calcium-ion implanted samples can be due to a relatively better passivation, whereas the reduction in degradation resistance in zinc-ion implanted samples can be attributed to the micro-galvanic effect.

SAP buran injury management of mangoes (mangifera indica L.) in sri lanka

International Nuclear Information System (INIS)

Krishnapillai, N.

2016-01-01

Sap burn injury is one of the major postharvest disorders that causes postharvest losses of mangoes. Popular dessert mango fruits from northern Sri Lanka were selected for this study. Mature mango fruits - Willard, Karuthakolumban, Chembaddan and Ambalavi - were harvested carefully with 5cm stalk for different treatments to minimize sap burn injury. Stalks were removed and fruits were dipped in GRAS compounds of 1 and 5% sodium chloride (Table salt) and 0.5 and 1% calcium hydroxide separately for 5 minutes. De-stemming and dipping fruits in 5% sodium chloride and 1% calcium hydroxide were effective in reducing sap burn injury in Karuthakolumban. However, 1% table salt and 0.5% calcium hydroxide successfully reduced sap burn injury in Willard, Chembaddan and Ambalavi mangoes. Fruit quality was measured in terms of pH, Total Soluble Solids (TSS) and marketability. Quality parameters of treated fruits were not significantly different (P=0.05) from non chemical treated good quality mango fruits. Sap management dynamics was very useful in controlling sap burn in Chembaddan and Ambalavi mangoes. No latex exudation was observed in these mangoes when stalk was broken by next day after harvesting. These results suggest that low cost environmentally friendly methods could be used to reduce sap burn injury in mangoes. (author)

An improved kilogram-scale preparation of atorvastatin calcium.

Science.gov (United States)

Novozhilov, Yuri V; Dorogov, Mikhail V; Blumina, Maria V; Smirnov, Alexey V; Krasavin, Mikhail

2015-01-01

If literature protocols are followed, conversion of an advanced ketal ester intermediate (available in kilogram quantities via a published Paal-Knorr synthesis) to cholesterol-lowering drug atorvastatin calcium is hampered by several process issues, particularly at the final stage where the hemi-calcium salt is obtained. We developed a high-yielding synthesis of atorvastatin calcium salt on 7 kg scale that affords >99.5% product purities by introducing the following key improvements: i. isolating the pure product of the ketal deprotection step as crystalline solid, and ii. using a convenient ethyl acetate extraction procedure to isolate the pure atorvastatin calcium at the ester hydrolysis and counter-ion exchange step. The convenient and operationally simple conversion of an advanced intermediate of atorvastatin to the clinically used hemi-calcium salt form of the drug that is superior to the methods obtainable from the literature is now available to facilitate the production of atorvastatin calcium on industrial scale. Graphical abstractStepwise ketal and tert-butyl ester group hydrolysis and a modified work-up protocol lead to a more convenient preparation of API-grade atorvastatin calcium.

Carbon Dioxide Adsorption by Calcium Zirconate at Higher Temperature

Directory of Open Access Journals (Sweden)

K. B. Kale

2012-12-01

Full Text Available The CO2 adsorption by calcium zirconate was explored at pre- and post- combustion temperature condition. The several samples of the calcium zirconate were prepared by different methods such as sol-gel, solid-solid fusion, template and micro-emulsion. The samples of the calcium zirconate were characterized by measurement of surface area, alkalinity/acidity, and recording the XRD patterns and SEM images. The CO2 adsorptions by samples of the calcium zirconate were studied in the temperature range 100 to 850 oC and the CO2 adsorptions were observed in the ranges of 6.88 to 40.6 wt % at 600 0C and 8 to 16.82 wt% at in between the temperatures 200 to 300 oC. The effect of Ca/Zr mol ratio in the samples of the calcium zirconate on the CO2 adsorption and alkalinity were discussed. The adsorbed moisture by the samples of the calcium zirconate was found to be useful for the CO2 adsorption. The promoted the samples of the calcium zirconate by K+, Na+, Rb+, Cs+, Ag+ and La3+ showed the increased CO2 adsorption. The exposure time of CO2 on the samples of the calcium zirconate showed the increased CO2 adsorption. The samples of the calcium zirconate were found to be regenerable and reusable several times for the adsorption of CO2 for at the post- and pre-combustion temperature condition. Copyright © 2012 by BCREC Undip. All rights reservedReceived: 23rd June 2012, Revised: 28th August 2012, Accepted: 30th August 2012[How to Cite: K. B. Kale, R. Y. Raskar, V. H. Rane and A. G.  Gaikwad (2012. Carbon Dioxide Adsorption by Calcium Zirconate at Higher Temperature. Bulletin of Chemical Reaction Engineering & Catalysis, 7 (2: 124-136. doi:10.9767/bcrec.7.2.3686.124-136] [How to Link / DOI: http://dx.doi.org/10.9767/bcrec.7.2.3686.124-136 ] | View in 

Preparation of plate-shape nano-magnesium hydroxide from asbestos tailings

International Nuclear Information System (INIS)

Du Gaoxiang; Zheng Shuilin

2009-01-01

To prepare magnesium hydroxide is one of the effective methods to the comprehensive utilization of asbestos tailings. Nano-scale magnesium hydroxide was prepared and mechanisms of in-situ surface modification were characterized in the paper. Process conditions of preparation of magnesium hydroxide from purified hydrochloric acid leachate of asbestos tailings were optimized and in-situ surface modification of the product was carried out. Results showed that optimum process conditions for preparing nano-scale magnesium hydroxide were as follows: initial concentration of Mg 2+ in the leachate was 22.75g/L, precipitant was NaOH solution (mass concentration 20%), reaction temperature was 50 deg. C, and reaction time was 5min. The diameter and thickness of the plate nano-scale magnesium hydroxide powder prepared under optimal conditions were about 100 nm and 10 nm, respectively. However, particle agglomeration was obvious, the particle size increased to micron-grade. Dispersity of the magnesium hydroxide powder could be elevated by in-situ modification by silane FR-693, titanate YB-502 and polyethylene glycol and optimum dosages were 1.5%, 1.5% and 0.75% of the mass of magnesium hydroxide, respectively. All of the modifiers adsorbed chemically on surfaces of magnesium hydroxide particles, among which Si-O-Mg bonds formed among silane FR-693 and the particle surfaces and Ti-O-Mg among titanate YB-502 and the surfaces.

Structural Properties of the Cr(III)-Fe(III) (Oxy)Hydroxide Compositional Series: Insights for a Nanomaterial 'Solid Solution'

International Nuclear Information System (INIS)

Tang, Y.; Zhang, L.; Michel, F.M.; Harrington, R.; Parise, J.B.; Reeder, R.J.

2010-01-01

Chromium(III) (oxy)hydroxide and mixed Cr(III)-Fe(III) (oxy)hydroxides are environmentally important compounds for controlling chromium speciation and bioaccessibility in soils and aquatic systems and are also industrially important as precursors for materials and catalyst synthesis. However, direct characterization of the atomic arrangements of these materials is complicated because of their amorphous X-ray properties. This study involves synthesis of the complete Cr(III)-Fe(III) (oxy)hydroxide compositional series, and the use of complementary thermal, microscopic, spectroscopic, and scattering techniques for the evaluation of their structural properties. Thermal analysis results show that the Cr end member has a higher hydration state than the Fe end member, likely associated with the difference in water exchange rates in the first hydration spheres of Cr(III) and Fe(III). Three stages of weight loss are observed and are likely related to the loss of surface/structural water and hydroxyl groups. As compared to the Cr end member, the intermediate composition sample shows lower dehydration temperatures and a higher exothermic transition temperature. XANES analysis shows Cr(III) and Fe(III) to be the dominant oxidation states. XANES spectra also show progressive changes in the local structure around Cr and Fe atoms over the series. Pair distribution function (PDF) analysis of synchrotron X-ray total scattering data shows that the Fe end member is nanocrystalline ferrihydrite with an intermediate-range order and average coherent domain size of ∼27 (angstrom). The Cr end member, with a coherent domain size of ∼10 (angstrom), has only short-range order. The PDFs show progressive structural changes across the compositional series. High-resolution transmission electron microscopy (HRTEM) results also show the loss of structural order with increasing Cr content. These observations provide strong structural evidence of chemical substitution and progressive structural

Arsenic species in weathering mine tailings and biogenic solids at the Lava Cap Mine Superfund Site, Nevada City, CA

Directory of Open Access Journals (Sweden)

Ashley Roger P

2011-01-01

Full Text Available Abstract Background A realistic estimation of the health risk of human exposure to solid-phase arsenic (As derived from historic mining operations is a major challenge to redevelopment of California's famed "Mother Lode" region. Arsenic, a known carcinogen, occurs in multiple solid forms that vary in bioaccessibility. X-ray absorption fine-structure spectroscopy (XAFS was used to identify and quantify the forms of As in mine wastes and biogenic solids at the Lava Cap Mine Superfund (LCMS site, a historic "Mother Lode" gold mine. Principal component analysis (PCA was used to assess variance within water chemistry, solids chemistry, and XAFS spectral datasets. Linear combination, least-squares fits constrained in part by PCA results were then used to quantify arsenic speciation in XAFS spectra of tailings and biogenic solids. Results The highest dissolved arsenic concentrations were found in Lost Lake porewater and in a groundwater-fed pond in the tailings deposition area. Iron, dissolved oxygen, alkalinity, specific conductivity, and As were the major variables in the water chemistry PCA. Arsenic was, on average, 14 times more concentrated in biologically-produced iron (hydroxide than in mine tailings. Phosphorous, manganese, calcium, aluminum, and As were the major variables in the solids chemistry PCA. Linear combination fits to XAFS spectra indicate that arsenopyrite (FeAsS, the dominant form of As in ore material, remains abundant (average: 65% in minimally-weathered ore samples and water-saturated tailings at the bottom of Lost Lake. However, tailings that underwent drying and wetting cycles contain an average of only 30% arsenopyrite. The predominant products of arsenopyrite weathering were identified by XAFS to be As-bearing Fe (hydroxide and arseniosiderite (Ca2Fe(AsO43O3•3H2O. Existence of the former species is not in question, but the presence of the latter species was not confirmed by additional measurements, so its identification is

Physical and chemical properties of calcium doped neodymium manganite

International Nuclear Information System (INIS)

Tikhonova, L.A.; Zhuk, P.P.; Tonoyan, A.A.; Vecher, A.A.

1991-01-01

Physical and chemical properties of calcium doped neodymium manganite were investigated. It was shown that structure of perovskite with O'-orthorhombic distortion was characteristic for solid solutions of Nd 1-x Ca x MnO 3 (x=0-0.5). Maximum of conductivity for samples with x=0.2 was determined. Inversion of conductivity from p- (x=0) to n-type (x=0.5) was observed in increase of concentration of calcium doped addition. Values of thermal expansion coefficient of studied solid solutions of Nd 1-x Ca x MnO 3 didn't depend on concentration of doped addition within the range 700 to 1200 K and were (9.9-11.3)·10 -6 K -1

Preparation of Silicon by Calcium Reduction of Purified Rice Husk Ash

International Nuclear Information System (INIS)

Swe Zin Tun

2011-12-01

This research has studied on the possibility of production and preparation of silicon powder from rice husk ash (RHA) as raw material. RHA from gasifier, a waste product of the rice mill is rich in silica which contains 90.43% of silica. RHAs were purified by precipitation method using 1.5N, 2N, 2.5N and 3N of sodium hydroxide solution and 4.5N, 5N, 5.5N and 6.5N of sulphuric acid solution. The highest yield percent of silica was given by using 2.5N sodium hydroxide solution and 5N sulphuric acid solution X-ray fluoresence (XRF), X-rays diffraction (HRD) and Fourier transform infrared (FTRI) spectra were applied for determination of mineral content and chemical bonding in extracted silica and rice husk ash. Metallothermic reduction of purified extracted silica with calcium was investigated within the temperacture range of 700-900 C. The reduction product was characterized by XRD, XRF and scanning electron microcopy (SEM). The effect of temperature and reaction time in which reduction process was studied in this research.

Calcium phosphates: what is the evidence?

Science.gov (United States)

Larsson, Sune

2010-03-01

A number of different calcium phosphate compounds such as calcium phosphate cements and solid beta-tricalcium phosphate products have been introduced during the last decade. The chemical composition mimics the mineral phase of bone and as a result of this likeness, the materials seem to be remodeled as for normal bone through a cell-mediated process that involves osteoclastic activity. This is a major difference when compared with, for instance, calcium sulphate compounds that after implantation dissolve irrespective of the new bone formation rate. Calcium phosphates are highly biocompatible and in addition, they act as synthetic osteoconductive scaffolds after implantation in bone. When placed adjacent to bone, osteoid is formed directly on the surface of the calcium phosphate with no soft tissue interposed. Remodeling is slow and incomplete, but by adding more and larger pores, like in ultraporous beta-tricalcium phosphate, complete or nearly complete resorption can be achieved. The indications explored so far include filling of metaphyseal fracture voids or bone cysts, a volume expander in conjunction with inductive products, and as a carrier for various growth factors and antibiotics. Calcium phosphate compounds such as calcium phosphate cement and beta-tricalcium phosphate will most certainly be part of the future armamentarium when dealing with fracture treatment. It is reasonable to believe that we have so far only seen the beginning when it comes to clinical applications.

Solid-soluted content of cerium in solid solution of sphene

International Nuclear Information System (INIS)

Zhao Wei; Teng Yuancheng; Li Yuxiang; Ren Xuetan; Huang Junjun

2010-01-01

The sphene solid solution was synthesized by solid-state method,with calcium carbonate, silica, titanium dioxide, cerium oxalate and alumina as raw materials. The solid-soluted content of cerium in sphene was researched by means of X-ray diffraction (XRD), backscattering scanning electron microscopy (BSE), energy dispersive spectroscopy (EDS) and so on. The influence of A l3+ ion introduction to sphene on the solid-soluted content of cerium in sphene solid solution was studied. The results indicate that when introducing Al 3+ to sphene as electrovalence compensation, Ce 4+ could be well solidified to Ca 1-x Ce x Ti 1-2x A l2x SiO 5 , and the solid-soluted content is approximately 12.61%. With no electrovalence compensation, Ce 4+ could be solidified to Ca 1-2x Ce x TiSiO 5 , and the solid-soluted content is approximately 10.98%. The appropriate synthesis temperature of sphene solid solution is 1 260 degree C.(authors)

Nickel and cobalt bimetallic hydroxide catalysts for urea electro-oxidation

International Nuclear Information System (INIS)

Yan Wei; Wang Dan; Botte, Gerardine G.

2012-01-01

Nickel–Cobalt bimetallic hydroxide electrocatalysts, synthesized through a one-step electrodeposition method, were evaluated for the oxidation of urea in alkaline conditions with the intention of reducing the oxidation overpotential for this reaction. The Nickel–Cobalt bimetallic hydroxide catalysts were characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDXS), Raman spectroscopy, cyclic voltammetry (CV), and polarization techniques. A significant reduction in the overpotential (150 mV) of the reaction was observed with the Nickel–Cobalt bimetallic hydroxide electrode (ca. 43% Co content) when compared to a nickel hydroxide electrode. The decrease of the urea oxidation potential on the Nickel–Cobalt bimetallic hydroxide electrodes reveals great potential for future applications of urea electro-oxidation, including wastewater remediation, hydrogen production, sensors, and fuel cells.

Iodine Sequestration Using Delafossites and Layered Hydroxides

International Nuclear Information System (INIS)

J.D. Pless; J.B. Chwirka; J.L. Krumhansl

2006-01-01

The objective of this document is to report on early success for sequestering 129 I. Sorption coefficients (K d ) for I - and IO 3 - onto delafossites, spinels and layered metal hydroxides were measured in order to compare their applicability for sequestering 129 I. The studies were performed using a dilute fluid composition representative of groundwater indigenous to the Yucca mountain area. Delafossites generally exhibited relatively poor sorption coefficients ( 1.7 mL/g). In contrast, the composition of the layered hydroxides significantly affects their ability to sorb I. Cu/Al and Cu/Cr layered hydroxide samples exhibit K d 's greater than 10 3 mL/g for both I - and IO 3 -

Preparation of calcium phosphate paste

International Nuclear Information System (INIS)

Mohd Reusmaazran Yusof; Norzita Yaacob; Idris Besar; Che Seman Mahmood; Rusnah Mustafa

2010-01-01

Calcium phosphate paste were prepared by mixing between calcium sodium potassium phosphate, Ca 2 NaK (PO 4 ) 2 (CSPP) and monocalcium phosphate monohydrate, Ca(H 2 PO 4 ) 2 .H 2 O (MCPM). CSPP were obtained by reaction between calcium hydrogen phosphate (CaHPO 4 ), potassium carbonate (K 2 CO 3 ) and sodium carbonate (Na 2 CO 3 ) in solid state sintering process followed by quenching in air at 1000 degree Celsius. The paste was aging in simulated body fluid (SBF) for 0.5, 1, 3, 6, 12, 24, 48 hrs, 3, 7 and 14 days. The morphological investigation indicated the formation of apatite crystal were first growth after 24 hours. The obvious growth of apatite crystal was shown at 3 days. The obvious growth of apatite crystal was shown in 7 and 14 days indicated the prediction of paste would have rapid reaction with bone after implantation. (author)

Nickel-cobalt hydroxide nanosheets: Synthesis, morphology and electrochemical properties

Czech Academy of Sciences Publication Activity Database

Schneiderová, Barbora; Demel, Jan; Zhigunov, Alexander; Bohuslav, Jan; Tarábková, Hana; Janda, Pavel; Lang, Kamil

2017-01-01

Roč. 499, AUG (2017), s. 138-144 ISSN 0021-9797 Institutional support: RVO:61388980 ; RVO:61389013 ; RVO:61388955 Keywords : Hydroxide nanosheets * Delamination * Exfoliation * Layered nickel hydroxide * Layered cobalt hydroxide * Electrode material Subject RIV: CA - Inorganic Chemistry; CF - Physical ; Theoretical Chemistry (UFCH-W); CD - Macromolecular Chemistry (UMCH-V) OBOR OECD: Inorganic and nuclear chemistry; Physical chemistry (UFCH-W); Polymer science (UMCH-V) Impact factor: 4.233, year: 2016

Enhancing the antibacterial activity of the gold standard intracanal medicament with incorporation of silver zeolite: An in vitro study.

Science.gov (United States)

Ghatole, Kiran; Gowdra, Ramesh Halebathi Giriyappa; Azher, Samer; Sabharwal, Sumit; Singh, Veerandar T; Sundararajan, Bharath Vardhana

2016-01-01

Enterococcus faecalis is a persistent organism that plays a major role in the etiology of persistent periradicular lesions after root canal treatment has been associated with different forms of periradicular disease including primary endodontic infections and persistent infections. The present study compares the antibacterial activities of calcium hydroxide, calcium hydroxide mixed with silver zeolite, and calcium hydroxide mixed with 2% chlorhexidine against E. faecalis using direct contact test. The test materials of the in vitro experimental study were grouped as group 1-calcium hydroxide mixed with sterile water, group 2-2% silver zeolite added in calcium hydroxide mixed with sterile water, and group 3-calcium hydroxide mixed with 2% chlorhexidine. The bottom of microtiter plate were coated with freshly mixed tested material and a 10 μL of bacterial suspension was placed. After 1 h of incubation at 37°C, brain-heart infusion (BHI) broth (245 μL) was added and mixed for 2 min. These were designated as "subgroup 1" wells. A volume of 15 μL of broth then transferred from subgroup 1 wells to an adjacent set of four wells containing fresh BHI medium (215 μL); these wells were designated as "subgroup 2"' wells. The optical density was measured by a spectrophotometer after the first day, third day, and seventh day. One-way analysis of variance (ANOVA) and Tukey tests were performed for the analysis. Calcium hydroxide mixed with silver zeolite showed maximum antibacterial activity. Silver zeolite can be added in calcium hydroxide to enhance the latter's antibacterial activity against E. faecalis.

Aluminum hydroxide issue closure package

International Nuclear Information System (INIS)

Bergman, T.B.

1998-01-01

Aluminum hydroxide coatings on fuel elements stored in aluminum canisters in K West Basin were measured in July and August 1998. Good quality data was produced that enabled statistical analysis to determine a bounding value for aluminum hydroxide at a 99% confidence level. The updated bounding value is 10.6 kg per Multi-Canister Overpack (MCO), compared to the previously estimated bounding value of 8 kg/MCO. Thermal analysis using the updated bounding value, shows that the MCO generates oxygen concentrate that are below the lower flammability limits during the 40-year interim storage period and are, therefore, acceptable

Mg-doped biphasic calcium phosphate by a solid state reaction route: Characterization and evaluation of cytotoxicity

Energy Technology Data Exchange (ETDEWEB)

Webler, Geovana D. [Instituto de Física, Universidade Federal de Alagoas, Maceió-AL 57072970 (Brazil); Correia, Ana C.C.; Barreto, Emiliano [Laboratório de Biologia Celular, Universidade Federal de Alagoas, Maceió-AL 57072970 (Brazil); Fonseca, Eduardo J.S., E-mail: eduardo@fis.ufal.br [Instituto de Física, Universidade Federal de Alagoas, Maceió-AL 57072970 (Brazil)

2015-07-15

Hydroxyapatite (HAP) and β-tricalcium phosphate (β-TCP) are widely used in tissue engineering because of their chemical similarity to the inorganic bone phase. In this work, we prepare biphasic calcium phosphate (BCP, a mixture of HAP and β-TCP) doped with different concentrations of magnesium to investigate the influence of magnesium on the BCP crystal structure. Magnesium is known to be an important element in the composition of bones and teeth. Recent research has shown that the doping of magnesium into BCP improves its bone metabolism and mechanical properties without affecting its biocompatibility. The samples were prepared by solid-state reaction from calcium carbonate, monobasic ammonium phosphate, and magnesium nitrate hexahydrate. Varying concentrations of magnesium were used and its modifications were examined by different characterization techniques. The phase composition and morphology of the ceramic powders were characterized by X-ray diffraction and scanning electron microscopy, respectively. The functional groups were analyzed using Fourier transform infrared spectroscopy and Raman spectroscopy. Cell viability experiments, using macrophage-like cell lines J774, showed that the synthesized Mg-doped BCP did not exhibit cytotoxicity regardless of the doses assayed or the different concentrations of magnesium used, suggesting it as a good material for potential biological applications. - Highlights: • Simple and fast method for the preparation of the Mg-BCP. • Study of the influence of the incorporation of Mg in the BCP. • Cell viability showed that the synthesized Mg-BCP did not exhibit cytotoxicity.

Mg-doped biphasic calcium phosphate by a solid state reaction route: Characterization and evaluation of cytotoxicity

International Nuclear Information System (INIS)

Webler, Geovana D.; Correia, Ana C.C.; Barreto, Emiliano; Fonseca, Eduardo J.S.

2015-01-01

Hydroxyapatite (HAP) and β-tricalcium phosphate (β-TCP) are widely used in tissue engineering because of their chemical similarity to the inorganic bone phase. In this work, we prepare biphasic calcium phosphate (BCP, a mixture of HAP and β-TCP) doped with different concentrations of magnesium to investigate the influence of magnesium on the BCP crystal structure. Magnesium is known to be an important element in the composition of bones and teeth. Recent research has shown that the doping of magnesium into BCP improves its bone metabolism and mechanical properties without affecting its biocompatibility. The samples were prepared by solid-state reaction from calcium carbonate, monobasic ammonium phosphate, and magnesium nitrate hexahydrate. Varying concentrations of magnesium were used and its modifications were examined by different characterization techniques. The phase composition and morphology of the ceramic powders were characterized by X-ray diffraction and scanning electron microscopy, respectively. The functional groups were analyzed using Fourier transform infrared spectroscopy and Raman spectroscopy. Cell viability experiments, using macrophage-like cell lines J774, showed that the synthesized Mg-doped BCP did not exhibit cytotoxicity regardless of the doses assayed or the different concentrations of magnesium used, suggesting it as a good material for potential biological applications. - Highlights: • Simple and fast method for the preparation of the Mg-BCP. • Study of the influence of the incorporation of Mg in the BCP. • Cell viability showed that the synthesized Mg-BCP did not exhibit cytotoxicity

Thermodynamics of calcium-isotope-exchange reactions. 1. Exchange between isotopic calcium carbonates and aqueous calcium ions

International Nuclear Information System (INIS)

Zhang, R.S.; Nash, C.P.; Rock, P.A.

1988-01-01

This paper reports the authors results for the direct experimental determination of the equilibrium constant for the calcium-isotope-exchange reaction 40 CaCO 3 (s) + 44 CaCl 2 (aq) reversible 44 CaCO 2 (s) + 40 CaCl 2 (aq). The reaction was studied in electrochemical double cells without liquid junction of the type shown in eq 2. The experimental value of the equilibrium constant at 295 +/- 2 K is K = 1.08 +/- 0.02. The experimental value for K is compared with the values of K calculated for various model reactions according to the statistical thermodynamic theory of isotope effects. The isotopic solid carbonates were modeled according to both the Debye and Kieffer theories. No structured models of solvated isotopic aqueous calcium ions yield calculated equilibrium constants in agreement with their experimental results. This conclusion is in agreement with published molecular dynamics calculations which show that the aqueous solvation of Ca 2 =(aq) is essentially unstructured

Aluminium hydroxide-induced granulomas in pigs

DEFF Research Database (Denmark)

Valtulini, S; Macchi, C; Ballanti, P

2005-01-01

The effect of intramuscular injection of 40 mg/2 ml aluminium hydroxide in the neck of pigs was examined in a number of ways. The investigation followed repeated slaughterhouse reports, according to which 64.8% of pigs from one particular farm were found at slaughter to have one or more nodules...... in the muscles of the neck (group slaughtered). The pigs had been injected with a vaccine containing 40 mg/2 ml dose of aluminium hydroxide as adjuvant. Research consisted of two phases: first, an epidemiological study was carried out, aimed at determining the risk factors for the granulomas. The results...... and adjuvant) to pigs inoculated twice with apyrogenic bi-distilled water (group water) and to pigs inoculated once with the adjuvant and once with apyrogenic bi-distilled water (group adjuvant/water). Both studies agreed in their conclusions, which indicate that the high amount of aluminium hydroxide...

Electrochemical characterization of calcium cobaltite based porous electrodes

International Nuclear Information System (INIS)

Fulgencio, E.B.G.A.; Vasconcelos, K.; Silva, R.M.; Melo, P.; Caetano, A.A.; Campos, L.F.A.; Dutra, R.P.S.; Macedo, D.A.

2016-01-01

Materials based on alkali metal oxides and alkaline earth metal have shown high technological interest in recent years. Among these materials, calcium and cobalt oxide composition Ca_3Co_4O_9 (C349) has emerged as thermoelectric material and, more recently, as cathode for solid oxide fuel cell (SOFC). In this study, C349 powder was obtained by solid state reaction of a mixture containing cobalt oxide and calcium carbonate from shellfish shells (CaCO_3 ∼ 98%), previously calcined at 550° C. Symmetrical cells (cathode / substrate / cathode) were prepared by screen printing of C349 electrodes in gadolinium-doped ceria substrates. The characterization by electrochemical impedance spectroscopy revealed that the C349 obtained in this work has an area specific resistance compatible with electrodes obtained by chemical routes (from literature). (author)

In vitro evaluation of the morphologic changes on the root dentine irradiated by CO2 laser associated or not to calcium hydroxide application

International Nuclear Information System (INIS)

Romano, Ana Cristina Cury Camargo

2003-01-01

This in vitro study has evaluated the structural changes on the root dentine irradiated by a CO 2 laser associated or not to calcium hydroxide application, from the irradiated surface analysis by means of Scanning Electronic Microscopy (SEM). The purpose of this evaluation has been the study of an alternative method for the treatment of dentine hypersensitivity. Fourteen human teeth were utilized, third molars, divided into 7 groups. Group I (control group) to which no treatment was applied; Groups II, III and IV were given an application of Ca (OH) 2 paste followed by C0 2 laser irradiation, lasting 5 seconds each with intervals of 10 seconds between each application, with continuous emission, power of 0.5 W (Group II), 1.0 W (Group III), and 1.5 W (Group IV); Groups V, VI, and VII were given laser irradiations without the Ca (OH) 2 paste following the same parameters applied to groups II, III, and IV respectively. Morphologic changes suggesting to fusion and re-solidification have been observed, as well as the presence of material obstructing the whole analyzed surface on groups II, III, and IV (laser + Ca (OH) 2 ). As for groups V, VI, and VII, it has been observed fusion, re-solidification, and cracks, and these results being statistically significant when compared the '(Ca (OH) 2 )' groups to the laser groups. No statistically significant differences were observed regarding the different powers applied in the groups that used the same treatment. Despite this result, it can be stated that powers above 1.0 W (DP = 125,38 W/cm 2 ) are unfavorable due to the undesirable morphologic alterations and aesthetic compromising. (author)

Behavior of hydroxide at the water/vapor interface

Science.gov (United States)

Winter, Bernd; Faubel, Manfred; Vácha, Robert; Jungwirth, Pavel

2009-06-01

Hydroxide and hydronium, which represent the ionic products of water autolysis, exhibit a peculiar surface behavior. While consensus has been established that the concentration of hydronium cations is enhanced at the surface with respect to the bulk, the affinity of hydroxide anions for the water/vapor interface has been a subject of an ongoing controversy. On the one hand, electrophoretic and titration measurements of air bubbles or oil droplets in water have been interpreted in terms of a dramatic interfacial accumulation of OH -. On the other hand, surface-selective non-linear spectroscopies, surface tension measurements, and molecular simulations show no or at most a weak surface affinity of hydroxide ions. Here, we summarize the current situation and provide new evidence for the lack of appreciable surface enhancement of OH -, based on photoelectron spectroscopy from a liquid jet and on molecular dynamics simulations with polarizable potentials at varying hydroxide concentrations.

Antimony removal from aqueous solutions using Zirconium hydroxide

International Nuclear Information System (INIS)

Petrescu, D.; Velciu, L.; Bucur, C.

2016-01-01

In this paper it is presented an experimental test for non-radioactive antimony removal from aqueous solutions using zirconium hydroxide powder. Also, it was studied how the temperature and pH influences antimony adsorption onto zirconium hydroxide surface. After the adsorption, solutions were filtered on Cellulose Mixed Ester Membrane with 0.2 μm pore size to remove the zirconium powder and then the aqueous solutions were sent to Inductively Coupled Plasma Optic Emission Spectrometry (ICP-OES) for quantitative analysis of Sb. Zirconium hydroxide powders were examined by optical microscopy. For the solutions that were tested at pH 4.5 and 10.2 the antimony concentration dropped below the detection limit of ICP-OES device, proof of antimony adsorption on zirconium hydroxide. Also, for the other tested solutions which had pH=12 the antimony concentration reduced with 77% and 80%. The temperature had no influence upon adsorption mechanism. (authors)

Electrochemical properties of lanthanum nitride with calcium nitride additions

International Nuclear Information System (INIS)

Lesunova, R.P.; Fishman, L.S.

1986-01-01

This paper reports on the electrochemical properties of lanthanum nitride with calcium nitride added. The lanthanum nitride was obtained by nitriding metallic lanthanum at 870 K in an ammonia stream. The product contained Cl, Pr, Nd, Sm, Fe, Ca, Cu, Mo, Mg, Al, Si, and Be. The calcium nitride was obtained by nitriding metallic calcium in a nitrogen stream. The conductivity on the LaN/C 3 N 2 system components are shown as a function of temperature. A table shows the solid solutions to be virtually electronic conductors and the lanthanum nitride a mixed conductor

Layered double hydroxides

DEFF Research Database (Denmark)

López Rayo, Sandra; Imran, Ahmad; Hansen, Hans Chr. Bruun

2017-01-01

A novel zinc (Zn) fertilizer concept based on Zn doped layered double hydroxides (Zn-doped Mg-Fe-LDHs) has been investigated. Zn-doped Mg-Fe-LDHs were synthetized, their chemical composition was analyzed and their nutrient release was studied in buffered solutions with different pH values. Uptake...

Synthesis of hydroxyapatite with the use of calcium carbonate as of the biological precursor; Sintese de hidroxiapatita com o uso de carbonato de calcio de origem biologica como precurssor

Energy Technology Data Exchange (ETDEWEB)

Aguilar, M.S.; Di Lello, B.C.; Queiroz, F.; Campos, N.C., E-mail: marilzasa@oi.com.br [Universidade Estacio de Sa (UESA), Rio de Janeiro, RJ (Brazil). Departamento de Engenharia; Campos, J.B. [Universidade do Estado do Rio de Janeiro (PPGEM/UERJ), RJ (Brazil). Programa de Pos-Graduacao em Engenharia Mecanica

2014-07-01

This work describes the synthesis of hydroxyapatite from calcium from biological materials such as shells carbonate. In the syntheses performed, the calcium carbonate of biological origin was used as the precursor and through a precipitation reaction with phosphoric acid, was converted into calcium hydroxide. Sequentially, the precipitate was aged, filtered, washed, dried and calcined, and then transformed into hydroxyapatite. The characterization of the powders was performed by X-DR (X-ray diffraction) and SEM (scanning electron microscopy). DR-X as determined hydroxyapatite calcium phosphate phase calcium. SEM revealed a morphology of finely divided particles. The method B.E.T. showed values of specific area and volume of micropores consistent with the literature. The results of the characterizations proved feasible to use for obtaining biological hydroxyapatite materials used in the reaction conditions.(author)

Qualitative Analysis of Fourteen White Solids and Two Mixtures Using Household Chemicals.

Science.gov (United States)

Oliver-Hoyo, Maria; Allen, DeeDee; Solomon, Sally; Brook, Bryan; Ciraolo, Justine; Daly, Shawn; Jackson, Leia

2001-01-01

Describes a laboratory experiment in which students identify 11 white solids readily available in drugstores and supermarkets. Investigates solubility, pH, copper reduction, evolution of carbon dioxide bubbles, formation of starch-iodine complex, and formation of an insoluble hydroxide. (YDS)

Single sheet metal oxides and hydroxides

DEFF Research Database (Denmark)

Huang, Lizhi

The synthesis of layered double hydroxides (LDHs) provides a relatively easy and traditional way to build versatile chemical compounds with a rough control of the bulk structure. The delamination of LDHs to form their single host layers (2D nanosheets) and the capability to reassemble them offer......) Delamination of the LDHs structure (oxGRC12) with the formation of single sheet iron (hydr)oxide (SSI). (3) Assembly of the new 2D nanosheets layer by layer to achieve desired functionalities....

[Comparative study of the antimicrobial effect of various cavity liners used in conservative dentistry].

Science.gov (United States)

Pumarola Suñé, J; Espias Gómez, A; Canalda Sahli, C

1989-01-01

We have compared the microbiological activity of the following cavity liners: Life, Dycal II, Calcipulpe, Pure calcium hydroxide and Cavitec; against five different bacterial strains: Veillonella parvula, Bacteroides fragilis, Peptococcus s.p., Staphylococcus aureus, and Streptococcus beta hemolytic: The results demonstrate the higher antimicrobial activity of the manufactured cavity liners with calcium hydroxide base in comparison with the pure calcium hydroxide.

Synthesis of polymer nanocomposites using layered hydroxide salts (LHS)

International Nuclear Information System (INIS)

Machado, Paula F. de M.P.B.; Lona, Liliane M.F.; Marangoni, Rafael; Wypych, Fernando

2011-01-01

In this work latexes of poly (methyl methacrylate) were synthesized via emulsion polymerization using layered hydroxide salts (LHS) as reinforcements: zinc hydroxide nitrate (Zn 5 (OH) 8 (NO 3 ) 2 ·2H 2 O) and copper hydroxide acetate (Cu 2 (OH) 3 CH 3 COO.H 2 O). The LHSs were characterized by X-ray powder diffraction (XRPD). Mastersizer analysis indicated the particle diameter of the latexes. Molecular weights and conversion data were also obtained. (author)

Synthesis Of Magnesium-Aluminum Layered Double Hydroxides By Mechanochemical Method And Its Solid State Reaction Kinetics

Directory of Open Access Journals (Sweden)

Hongbo Y.

2015-06-01

Full Text Available A mechanochemical method is developed in preparing magnesium-aluminum-layered double hydroxides (MgAl-LDHs. This approach includes activation process and diffusion process. In order to verify the LDHs structure and study the reaction kinetics, X-ray diffraction (XRD patterns, inductively coupled plasma(ICP and physical adsorption instrument were characterized. The results show that activation time can change the surface of particles and affect the reaction grade. During the diffusion process, reaction time is the most important factor. The reaction energy (ΔQ was calculated that is 6kJ/mol.

Modification of oxide inclusions in calcium-treated Al-killed high sulphur steels

NARCIS (Netherlands)

Gollapalli, Veerababu; Rao, M.B.Venkata; Karamched, P.S.; Borra, C.R.; Roy, G.G.; Srirangam, Prakash

2018-01-01

A study has been carried out to understand the modification of alumina inclusions in Al-killed high sulphur steel with calcium treatment. For calcium treatment to be effective, a general practice is to desulphurise the steel to prevent the formation of solid CaS inclusions that are harmful to

Discharge Characteristics of the Nickel Hydroxide Electrode in 30% KOH

International Nuclear Information System (INIS)

Kim, Young Jin

1989-01-01

The discharge behavior of the nickel hydroxide electrode has been investigated in 30% KOH at 25 .deg. C. Two voltage plateaus are displayed on the discharge curve of C/20. It is shown that the impedance of the nickel hydroxide electrode increases with decrease of the discharge potential. The discharge behavior of the nickel hydroxide electrode has been investigated in 30% KOH indicating the reduction of the β-NiOOH to the β-Ni(OH) 2 by proton diffusion process and hence the electronic conductivity change of the nickel hydroxide electrode. Furthermore, the γ-NiOOH, produced by prolonged oxidation of the β-NiOOH in 30% KOH, discharges at a slightly lower potential than the β-Ni(OH) 2 that could result in the life-limiting factor of several alkaline electrolyte storage batteries using the nickel hydroxide electrode as the positive plate

Adsorption of procion red using layer double hydroxide Mg/Al

Directory of Open Access Journals (Sweden)

Muhammad Imron

2017-07-01

Full Text Available Layer double hydroxide Mg/Al was synthesized by inorganic synthetic method. Material was characterized using FTIR and XRD analyses and used as adsorbent of procion red dye in aqueous medium.  Factors that affect the adsorption process are adsorption time as the kinetic parameter; and the temperature and concentration of procion red as the thermodynamic parameter. FTIR spectra of layer double hydroxides showed unique vibration at wavenumber 1300 cm-1 and 1600 cm-1. Characterization using XRD shows diffraction angles at 29o, 27o, and 28o, which are typical of Mg/Al double layer hydroxides. Adsorption of procion red using layer double hydroxide Mg/Al resulted adsorption rate 7.1 minutes-1, maximum adsorption capacity 111.1 mg/g at 60 oC with increasing energy by increasing adsorption temperature.   Keywords: Layered double hydroxides, adsorption, procion red.

Intercalation studies of zinc hydroxide chloride: Ammonia and amino acids

Science.gov (United States)

Arízaga, Gregorio Guadalupe Carbajal

2012-01-01

Zinc hydroxide chloride (ZHC) is a layered hydroxide salt with formula Zn5(OH)8Cl2·2H2O. It was tested as intercalation matrix for the first time and results were compared with intercalation products of the well-known zinc hydroxide nitrate and a Zn/Al layered double hydroxide. Ammonia was intercalated into ZHC, while no significant intercalation occurred in ZHN. Aspartic acid intercalation was only achieved by co-precipitation at pH=10 with ZHC and pH=8 with zinc hydroxide nitrate. Higher pH resistance in ZHC favored total deprotonation of both carboxylic groups of the Asp molecule. ZHC conferred more thermal protection against Asp combustion presenting exothermic peaks even at 452 °C while the exothermic event in ZHN was 366 °C and in the LDH at 276 °C.

Crystal growth and characterization of calcium metaborate scintillators

Czech Academy of Sciences Publication Activity Database

Fujimoto, Y.; Yanagida, T.; Kawaguchi, N.; Fukuda, K.; Totsuka, D.; Watanabe, K.; Yamazaki, A.; Chani, V.; Nikl, Martin; Yoshikawa, A.

2013-01-01

Roč. 703, MAR (2013), s. 7-10 ISSN 0168-9002 Institutional support: RVO:68378271 Keywords : Czochralski method * single crystal * scintillator * calcium metaborate * luminescence Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.316, year: 2013

Contribution to the study of sorption mechanisms at solid-liquid interfaces: application to the cases of apatites and oxy-hydroxides; Contribution a l'etude des mecanismes de sorption aux interfaces solide-liquide: application aux cas des apatites et des oxy-hydroxydes

Energy Technology Data Exchange (ETDEWEB)

Duc, M

2002-11-15

Sorption-desorption phenomena play an important role in the transport of toxic and radioactive elements in surface and underground water in contact with solid matter. Selenium, which is one of the long-lived radionuclides present in radioactive waste, is characterized by several oxidation states and by anionic species in aqueous solutions. In order to predict its transport, we need a good knowledge of its sorption processes. We have studied the sorption of Se(IV) and Se(VI) on two types of solids present in natural media or which have been proposed as additives to active barriers: hydroxy-apatites, fluoro-apatite and iron oxi-hydroxides (goethite and hematite). Sorption mechanisms have been studied through an approach including several different and complementary methods: titrimetry, zeta-metry, scanning and transmission electron microscopy, infrared spectroscopy, X-ray diffraction, X-ray photo electron spectroscopy, etc... Results showed that Se(VI) is much less sorbed than Se(VI) on both types of solids. For Se(IV) the sorption mechanisms are different for iron oxides and apatites. On oxides, sorption increases when pH decreases. It can be interpreted by a surface complexation model, essentially through an inner sphere complex (monodentate or bidentate). Modelling of Se sorption curves was performed after the determination of acido-basic properties of oxides. However, the determination of the intrinsic properties of oxides is disturbed by several parameters identified as impurities, evolution of the solid in solution, kinetic and solubility of the solid. For apatites, selenium sorption proceeds by exchange with superficial groups, with a maximum of fixation at approximately pH 8. Thanks to XPS measurements and the elaboration of a mathematical model, we could determine the depth of penetration of both selenium and cadmium on apatites. (author)

On reactions of polymerization of p-element hydroxides in aqueous solutions

International Nuclear Information System (INIS)

Tikavyj, V.F.; Lesnikovich, A.I.

1978-01-01

The tendency of p-element hydroxides towards polymerization in aqueous solutions has been considered with respect to their location in the Periodic Table. Stable hydroxides of d-elements are practically all polymerized; among s-elements only berillium and magnesium hydroxides polymerize as the least dissociated ones. Hydroxides of the elements located to the right of the 4 Group and above the 5-th Period do not polymerize in aqueous solutions. The structure and tendency towards polymerization of In, Te, and I compounds have been studied. The tendency to polymerization of all hydroxides of p-elements located below the 4-th Period is explained from the standpoint of electron structure and the simplest thermodynamic analysis (entropy, enthalpy)

Effect of Arsenic on the Formation and Adsorption Property of Ferric Hydroxide Precipitates in ZVI Treatment

Energy Technology Data Exchange (ETDEWEB)

Peng, Xing; Xi, Beidou; Zhao, Ying; Shi, Qiantao; Meng, Xiaoguang; Mao, Xuhui; Jiang, Yonghai; Ma, Zhifei; Tan, Wenbing; Liu, Hongliang; Gong, Bin (Stevens); (Beijing NU); (CRAES); (Wuhan)

2017-08-14

Treatment of arsenic by zerovalent iron (ZVI) has been studied extensively. However, the effect of arsenic on the formation of ferric hydroxide precipitates in the ZVI treatment has not been investigated. We discovered that the specific surface area (ca. 187 m2/g) and arsenic content (ca. 67 mg/g) of the suspended solids (As-containing solids) generated in the ZVI treatment of arsenic solutions were much higher than the specific surface area (ca. 37 m2/g) and adsorption capacity (ca.12 mg/g) of the suspended solids (As-free solids) generated in the arsenic-free solutions. Arsenic in the As-containing solids was much more stable than the adsorbed arsenic in As-free solids. XRD, SEM, TEM, and selected area electron diffraction (SAED) analyses showed that the As-containing solids consisted of amorphous nanoparticles, while the As-free solids were composed of micron particles with weak crystallinity. Extended X-ray absorption fine structure (EXAFS) analysis determined that As(V) was adsorbed on the As-containing suspended solids and magnetic solid surfaces through bidentate binuclear complexation; and As(V) formed a mononuclear complex on the As-free suspended solids. The formation of the surface As(V) complexes retarded the bonding of free FeO6 octahedra to the oxygen sites on FeO6 octahedral clusters and prevented the growth of the clusters and their development into 3-dimensional crystalline phases.

The crystallinity of calcium phosphate powders influenced by the conditions of neutralized procedure with citric acid additions

International Nuclear Information System (INIS)

Li Chengfeng

2009-01-01

Calcium phosphate powders with nano-sized crystallinity were synthesized by neutralization using calcium hydroxide and orthophosphoric acid with the assistance of citric acid. The influence of processing parameters, such as free or additive citric acid, synthetic temperature and ripening time, on the crystallinity of hydroxyapatite were investigated. The results of X-ray diffraction and microstructure observations showed that the crystallinity and morphology of nano-sized hydroxyapatite particles were influenced by the presence or absence of citric acid. It was found that the crystallinities and crystallite sizes of hydroxyapatite powders prepared with the additive citric acid increased with increasing synthetic temperature and ripening time. Especially, the crystallinities of (h k 0) planes were raised and more homogeneously grown particles were obtained with increasing synthetic temperature

Photoluminescence studies on holmium (III) and praseodymium (III) doped calcium borophosphate (CBP) phosphors

Science.gov (United States)

Reddy Prasad, V.; Damodaraiah, S.; Devara, S. N.; Ratnakaram, Y. C.

2018-05-01

Using solid state reaction method, Ho3+ and Pr3+ doped calcium borophosphate (CBP) phosphors were prepared. These phosphors were characterized using XRD, SEM, FT-IR, 31P solid state NMR, photoluminescence (PL) and decay profiles. Structural details were discussed from XRD and FT-IR spectra. From 31P NMR spectra of these phosphors, mono-phosphate complexes Q0-(PO43-) were observed. Photoluminescence spectra were measured for both Ho3+ and Pr3+ doped calcium borophosphate phosphors and the spectra were studied for different concentrations. Decay curves were obtained for the excited level, 5F4+5S2 of Ho3+ and 1D2 level of Pr3+ in these calcium borophosphate phosphors and lifetimes were measured. CIE color chromaticity diagrams are drawn for these two rare earth ions in calcium borophosphate phosphors. Results show that Ho3+ and Pr3+ doped CBP phosphors might be served as green and red luminescence materials.

The use of dissolvable layered double hydroxide components in an in situ solid-phase extraction for chromatographic determination of tetracyclines in water and milk samples.

Science.gov (United States)

Phiroonsoontorn, Nattaphorn; Sansuk, Sira; Santaladchaiyakit, Yanawath; Srijaranai, Supalax

2017-10-13

This research presents a simple and green in situ solid phase extraction (is-SPE) combined with high-performance liquid chromatography (HPLC) for the simultaneous analysis of tetracyclines (TCs) including tetracycline, oxytetracycline, and chlortetracycline. In is-SPE, TCs were efficiently extracted through the precipitation formation of dissolvable layered double hydroxides (LDHs) by mixing the LDH components such as magnesium and aluminum ions (both in metal chloride salts) thoroughly in an alkaline sample solution. After the centrifugation, the precipitate was completely dissolved with trifluoroacetic acid to release the enriched TCs, and then analyzed by HPLC. Under optimized conditions, this method gave good enrichment factors (EFs) of 41-93 with low limits of detection (LODs) of 0.7-6μg/L and limits of quantitation (LOQs) of 3-15μg/L. Also, the proposed method was successfully applied for the determination of TCs in water and milk samples with the recoveries ranging from 81.7-108.1% for water and 55.7-88.7% for milk. Copyright © 2017 Elsevier B.V. All rights reserved.

Enhancing the antibacterial activity of the gold standard intracanal medicament with incorporation of silver zeolite: An in vitro study

OpenAIRE

Ghatole, Kiran; Gowdra, Ramesh Halebathi Giriyappa; Azher, Samer; Sabharwal, Sumit; Singh, Veerandar T.; Sundararajan, Bharath Vardhana

2016-01-01

Background: Enterococcus faecalis is a persistent organism that plays a major role in the etiology of persistent periradicular lesions after root canal treatment has been associated with different forms of periradicular disease including primary endodontic infections and persistent infections. The present study compares the antibacterial activities of calcium hydroxide, calcium hydroxide mixed with silver zeolite, and calcium hydroxide mixed with 2% chlorhexidine against E. faecalis using dir...

Thermochemical heat storage for high temperature applications. A review

Energy Technology Data Exchange (ETDEWEB)

Felderhoff, Michael [Max-Planck-Institut fuer Kohlenforschung, Muelheim an der Ruhr (Germany); Urbanczyk, Robert; Peil, Stefan [Institut fuer Energie- und Umwelttechnik e.V. (IUTA), Duisburg (Germany)

2013-07-01

Heat storage for high temperature applications can be performed by several heat storage techniques. Very promising heat storage methods are based on thermochemical gas solid reactions. Most known systems are metal oxide/steam (metal hydroxides), carbon dioxide (metal carbonates), and metal/hydrogen (metal hydrides) systems. These heat storage materials posses high gravimetric and volumetric heat storage densities and because of separation of the reaction products and their storage in different locations heat losses can be avoided. The reported volumetric heat storage densities are 615, 1340 and 1513 [ kWh m{sup -3}] for calcium hydroxide Ca(OH){sub 2}, calcium carbonate CaCO{sub 3} and magnesium iron hydride Mg{sub 2}FeH{sub 6} respectively. Additional demands for gas storage decrease the heat storage density, but metal hydride systems can use available hydrogen storage possibilities for example caverns, pipelines and chemical plants. (orig.)

The solubilities and solubility products of zirconium hydroxide and oxide after aging at 278, 313, and 333 K

Energy Technology Data Exchange (ETDEWEB)

Kobayashi, Taishi; Uemura, Takuya; Sasaki, Takayuki; Takagi, Ikuji [Kyoto Univ. (Japan). Dept. of Nuclear Engineering; Moriyama, Hirotake [Kyoto Univ. (Japan). Research Reactor Inst.

2016-07-01

The solubilities of zirconium hydroxide and oxide after aging at 278, 313, and 333 K were measured at 278, 298, 313, and 333 K in the pH{sub c} range of 0.3-7 in a 0.5 M ionic strength solution of NaClO{sub 4} and HClO{sub 4}. Size distributions of the colloidal species were investigated by ultrafiltration using membranes with different pore sizes, and the solid phases were examined by X-ray diffraction. The apparent solubility of zirconium amorphous hydroxide (Zr(OH){sub 4}(am)), prepared by the oversaturation method, decreased with increasing aging temperature (T{sub a}), and the size distributions obtained after aging at elevated temperatures indicated the growth of the colloidal species. We, therefore, suggested that agglomeration of the colloidal species and dehydration and crystallization of Zr(OH){sub 4}(am) as the solubility-limiting solid phase occurred over the course of aging at elevated temperatures. For sample solutions of the crystalline oxide (ZrO{sub 2}(cr)), the aging temperature had no significant effect on the solubility, but the solubility data at lower temperatures were found to be slightly higher than those at higher temperatures, implying a small fraction of the amorphous components. In the analysis of different solid phases (Zr(OH){sub 4}(s,T{sub a}), T{sub a} = 278, 313, and 333 K) depending on the aging temperatures, the solubility products (K{sub sp}, T{sub a}) were determined at different measurement temperatures, and the enthalpy change (Δ{sub r}H {sup circle}) for Zr{sup 4+} 4OH{sup -} <=> Zr(OH){sub 4}(s,T{sub a}) was calculated using the van't Hoff equation. The solid-phase-transformation process at elevated temperatures was also analyzed based on the obtained K{sub sp}, T{sub a} and Δ{sub r}H {sup circle} values.

Leaching characteristics of calcium-based compounds in MSWI Residues: From the viewpoint of clogging risk.

Science.gov (United States)

Xia, Yi; Zhang, Hua; Phoungthong, Khamphe; Shi, Dong-Xiao; Shen, Wen-Hui; Shao, Li-Ming; He, Pin-Jing

2015-08-01

Leachate collection system (LCS) clogging caused by calcium precipitation would be disadvantageous to landfill stability and operation. Meanwhile, calcium-based compounds are the main constituents in both municipal solid waste incineration bottom ash (MSWIBA) and stabilized air pollution control residues (SAPCR), which would increase the risk of LCS clogging once these calcium-rich residues were disposed in landfills. The leaching behaviors of calcium from the four compounds and municipal solid waste incineration (MSWI) residues were studied, and the influencing factors on leaching were discussed. The results showed that pH was the crucial factor in the calcium leaching process. CaCO3 and CaSiO3 began leaching when the leachate pH decreased to less than 7 and 10, respectively, while Ca3(PO4)2 leached at pHleaching rate for the different calcium-based compounds is as follows: CaSiO3>Ca3(PO4)2>CaCO3. The calcium leaching from the MSWIBA and SAPCR separately started from pHleaching respectively, which was proven by the X-ray diffraction results. Based on the leaching characteristics of the different calcium compounds and the mineral phase of calcium in the incineration residues, simulated computation of their clogging potential was conducted, providing the theoretical basis for the risk assessment pertaining to LCS clogging in landfills. Copyright © 2015 Elsevier Ltd. All rights reserved.

Rapid collection of iron hydroxide for determination of Th isotopes in seawater

Energy Technology Data Exchange (ETDEWEB)

Okubo, Ayako, E-mail: okubo.ayako@jaea.go.jp [Japan Atomic Energy Agency, Research Group for Analytical Chemistry (Japan); Obata, Hajime, E-mail: obata@aori.u-tokyo.ac.jp [Atmosphere Ocean Research Institute, The University of Tokyo (Japan); Magara, Masaaki, E-mail: magara.masaaki@jaea.go.jp [Japan Atomic Energy Agency, Research Group for Analytical Chemistry (Japan); Kimura, Takaumi, E-mail: kimura.takaumi@jaea.go.jp [Japan Atomic Energy Agency, Research Group for Analytical Chemistry (Japan); Ogawa, Hiroshi, E-mail: hogawa@aori.u-tokyo.ac.jp [Atmosphere Ocean Research Institute, The University of Tokyo (Japan)

2013-12-04

Graphical abstract: -- Highlights: •DIAION CR-20 chelating resin has successfully collected iron-hydroxide with Th isotopes. •Ferric ions in the iron hydroxide were bonded to functional groups of the chelating resin. •The time of preconcentration step was markedly reduced from a few days to 3–4 h. -- Abstract: This work introduces a novel method of recovery of iron hydroxide using a DIAION CR-20 chelating resin column to determine Th isotopes in seawater with a sector field (SF) inductively coupled plasma mass spectrometer (ICP-MS). Thorium isotopes in seawater were co-precipitated with iron hydroxide, and this precipitate was sent to chelating resin column. Ferric ions in the iron hydroxide were bonded to functional groups of the chelating resin directly, resulting in a pH increase of the effluent by release of hydroxide ion from the iron hydroxide. The co-precipitated thorium isotopes were quantitatively collected within the column, which indicated that thorium was retained on the iron hydroxide remaining on the chelating column. The chelating column quantitatively collected {sup 232}Th with iron hydroxide in seawater at flow rates of 20–25 mL min{sup −1}. Based on this flow rate, a 5 L sample was processed within 3–4 h. The >20 h aging of iron hydroxide tends to reduce the recovery of {sup 232}Th. The rapid collection method was successfully applied to the determination of {sup 230}Th and {sup 232}Th in open-ocean seawater samples.

Acid mine water neutralisation with ammonium hydroxide and ...

African Journals Online (AJOL)

This study showed that NH4OH can be used for treatment of acid mine drainage rich in sulphates and NH4OH can be recycled in the process. Hydrated lime treatment resulted in removal of the remaining ammonia using a rotary evaporator. Keywords: acid mine water, ammonium hydroxide, barium hydroxide, sulphate ...

Method of processing radioactive liquid wastes

International Nuclear Information System (INIS)

Kurumada, Norimitsu; Shibata, Setsuo; Wakabayashi, Toshikatsu; Kuribayashi, Hiroshi.

1984-01-01

Purpose: To facilitate the procession of liquid wastes containing insoluble salts of boric acid and calcium in a process for solidifying under volume reduction of radioactive liquid wastes containing boron. Method: A soluble calcium compound (such as calcium hydroxide, calcium oxide and calcium nitrate) is added to liquid wastes whose pH value is adjusted neutral or alkaline such that the molar ratio of calcium to boron in the liquid wastes is at least 0.2. Then, they are agitated at a temperature between 40 - 70 0 C to form insoluble calcium salt containing boron. Thereafter, the liquid is maintained at a temperature less than the above-mentioned forming temperature to age the products and, thereafter, the liquid is evaporated to condensate into a liquid concentrate containing 30 - 80% by weight of solid components. The concentrated liquid is mixed with cement to solidify. (Ikeda, J.)

Effect of surface states of layered double hydroxides on conductive and transport properties of nanocomposite polymer electrolytes

International Nuclear Information System (INIS)

Liao, C.-S.; Ye, W.-B.

2004-01-01

All solid-state poly(ethylene oxide) (PEO) nanocomposite electrolytes were made containing nanoscale fillers of layered double hydroxides (LDHs). Two kinds of LDHs with different surface states were prepared by aqueous co-precipitation method. The LDHs were added into PEO matrix to study the structures, conductivities and ionic transport properties of nanocomposite electrolytes. The structures of LDHs were characterized by infrared spectra, thermogravimetric analysis and wide-angle X-ray diffraction. With enhanced compatibility of LDH sheets by oligo(ethylene oxide) surface modification, the PEO/OMLDH nanocomposite electrolyte exhibits an amorphous morphology and an enhancement of conductivity by three orders of magnitude as compared to pure PEO electrolyte. The lithium ion transference number T Li + of PEO/LDH nanocomposite electrolyte measured with a value of 0.42 is two times higher than the one of pure PEO electrolyte, which can be attributed to the Lewis acid-base interaction between surface states of metal hydroxides and counter anions of lithium salts

Preparation And Characterization Of Modified Calcium Oxide From Natural Sources And Their Application In The Transesterification Of Palm Oil

Directory of Open Access Journals (Sweden)

Aqliliriana

2015-08-01

Full Text Available Abstract Calcium oxide catalysts were prepared from natural calcium sources such as limestone and mud creeper shell and the catalytic activities were evaluated in the transesterification of palm oil. The raw material which mainly composed of calcium carbonate can be easily converted to calcium oxide CaO after calcination above 1000 K for few hours. Abundant cheap sources benign high conversion and nontoxic become main advantages of these catalysts. The catalysts were characterized by XRF TGA XRD CO2-TPD SEM and BET methods. Thermal decomposition of CaCO3 will produced CaO which later will be converted into calcium hydroxide CaOH2 via simple hydration technique. Under optimum reaction condition methanol to oil ratio 151 catalyst loading 3 wt. reaction temperature 338 K for 5 hours the highest conversion of palm oil to methyl ester recorded were 98 and 94 when using modified limestone and mud creeper shell respectively. The results observed an increment up to 80 by using modified catalysts with characterization results showed high in basicity and surface area. Hence promising materials via simple and cheap method can be achieved.

Formation and filtration characteristics of solids generated in a high level liquid waste treatment process. Solids formation behavior from simulated high level liquid waste

International Nuclear Information System (INIS)

Kondo, Y.; Kubota, M.

1997-01-01

The solids formation behavior in a simulated high level liquid waste (HLLW) was experimentally examined, when the simulated HLLW was treated in the ordinary way of actual HLLW treatment process. Solids formation conditions and mechanism were closely discussed. The solids formation during a concentration step can be explained by considering the formation of zirconium phosphate, phosphomolybdic acid and precipitation of strontium and barium nitrates and their solubilities. For the solids formation during the denitration step, at least four courses were observed; formation of an undissolved material by a chemical reaction with each other of solute elements (zirconium, molybdenum, tellurium) precipitation by reduction (platinum group metals) formation of hydroxide or carbonate compounds (chromium, neodymium, iron, nickel, strontium, barium) and a physical adsorption to stable solid such as zirconium molybdate (nickel, strontium, barium). (author)

Dehydration-rehydration behaviour of zirconium hydroxide and aluminium hydroxide coprecipitated hydrogel

International Nuclear Information System (INIS)

Mitra, N.K.; Guha, P.; Basumajumdar, A.

1989-01-01

Equilibrium dehydration loss experiments on zirconium and aluminium hydroxide coprecipitated hyrogels were carried out up to 600deg and the above heat treated samples were subjected to rehydration at various humidities in order to study the structural flexibilties of the above hydrogel with respect to orientation of water molecules. (author). 6 refs., 3 tabs

Effect of calcium hydroxide and double and triple antibiotic pastes on the bond strength of epoxy resin-based sealer to root canal dentin.

Science.gov (United States)

Akcay, Merve; Arslan, Hakan; Topcuoglu, Hüseyin Sinan; Tuncay, Oznur

2014-10-01

The aim of this study was to evaluate the effects of calcium hydroxide (CH) and triple (TAP) and double (DAP) antibiotic pastes on the bond strength of an epoxy resin-based sealer (AH Plus Jet; Dentsply DeTrey, Konstanz, Germany) to the root canal dentin. Sixty-four single-rooted human mandibular premolars were decoronated and prepared using the rotary system to size 40. The specimens were randomly divided into a control group (without intracanal dressing) and 3 experimental groups that received an intracanal dressing with either CH, DAP, or TAP (n = 16). The intracanal dressing was removed by rinsing with 10 mL 17% EDTA followed by 10 mL 2.5% sodium hypochlorite. The root canals were then obturated with gutta-percha and AH Plus Jet sealer. A push-out test was used to measure the bond strength between the root canal dentin and the sealer. The data were analyzed using 2-way analysis of variance and Tukey post hoc tests to detect the effect of the independent variables (intracanal medicaments and root canal thirds) and their interactions on the push-out bond strength of the root canal filling material to the root dentin (P = .05). The push-out bond strength values were significantly affected by the intracanal medicaments (P .05). In the middle and apical third, the bond strength of the TAP group was higher than those of the CH and DAP groups (P < .05). The DAP and CH did not affect the bond strength of the epoxy resin-based sealer. Additionally, the TAP improved the bond strength of the epoxy resin-based sealer in the middle and apical thirds. Copyright © 2014 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Removal of calcium hydroxide from Weine Type II systems using photon-induced photoacoustic streaming, passive ultrasonic, and needle irrigation: a microcomputed tomography study

Directory of Open Access Journals (Sweden)

Adam LLOYD

Full Text Available ABSTRACT Objective This study compared the effectiveness of Er:YAG laser-activated irrigation (PIPS, passive ultrasonic irrigation (PUI with EndoUltra and standard needle irrigation (SNI in the removal of calcium hydroxide [Ca(OH2] from the mesial roots of Weine Type II mandibular molars. Material and Methods Thirty mandibular molars were screened by µCT for the presence of mesial roots with complex intra-canal anatomy and a common apical foramen. The teeth were enlarged to a standardized 25/.06 preparation and filled with Ca(OH2 paste. Specimens were divided into three groups (n=10 according to the technique used for Ca(OH2 removal: PIPS, at 15 Hz and 20 mJ using a 9 mm long, 600 µm diameter tip; PUI using a 15/.02 tip; and SNI (30 Ga. side-vented needle. Equal volumes of 8.25% NaOCl and 17% EDTA were used in all groups. µCT was used to measure the initial amount of Ca(OH2 present and to assess the residual volume of Ca(OH2 following each irrigation protocol. Data were analyzed using Tukey HSD and Kruskal-Wallis tests (α=5%. Results The mean volume of Ca(OH2 before removal was significantly higher in the coronal third than in the middle and apical third (p0.05. PIPS (median 0%; IQR: 0-0 showed significant higher Ca(OH2 removal in the apical third than PUI (median 100%, IQR: 85-100 and SNI (median 47%; IQR: 16-72 (p<0.001. Conclusions PIPS laser-activation was more effective for the removal of Ca(OH2 from mesial roots of mandibular molars with Weine Type II canal configurations than PUI with EndoUltra and SNI.

Cation interdiffusion in polycrystalline calcium and strontium titanate

International Nuclear Information System (INIS)

Butler, E.P.; Jain, H.; Smyth, D.M.

1991-01-01

This paper discusses a method that has been developed to study bulk lattice interdiffusion between calcium and strontium titanate by fabrication of a diffusion couple using cosintering. The measured interdiffusion coefficients, D(C), indicate that strontium impurity diffusion in calcium titanate occurs at a faster rate than calcium impurity diffusion in strontium titanate. These interdiffusion coefficients are composition independent when the concentration of the calcium cation exceeds that of the strontium cation; otherwise D(C) is strongly composition dependent. Investigations into the effect of cation nonstoichiometry give results that are consistent with a defect incorporation reaction in which excess TiO 2 , within the solid solubility limit, produces A-site cation vacancies as compensating defects. The interdiffusion coefficients increase with increasing concentrations of TiO 2 , so it is concluded that interdiffusion of these alkaline-earth cations in their titanates occurs via a vacancy mechanism

Determination of Iodate in Food, Environmental, and Biological Samples after Solid-Phase Extraction with Ni-Al-Zr Ternary Layered Double Hydroxide as a Nanosorbent

Directory of Open Access Journals (Sweden)

Hossein Abdolmohammad-Zadeh

2012-01-01

Full Text Available Nanostructured nickel-aluminum-zirconium ternary layered double hydroxide was successfully applied as a solid-phase extraction sorbent for the separation and pre-concentration of trace levels of iodate in food, environmental and biological samples. An indirect method was used for monitoring of the extracted iodate ions. The method is based on the reaction of the iodate with iodide in acidic solution to produce iodine, which can be spectrophotometrically monitored at 352 nm. The absorbance is directly proportional to the concentration of iodate in the sample. The effect of several parameters such as pH, sample flow rate, amount of nanosorbent, elution conditions, sample volume, and coexisting ions on the recovery was investigated. In the optimum experimental conditions, the limit of detection (3s and enrichment factor were 0.12 μg mL−1 and 20, respectively. The calibration graph using the preconcentration system was linear in the range of 0.2–2.8 μg mL−1 with a correlation coefficient of 0.998. In order to validate the presented method, a certified reference material, NIST SRM 1549, was also analyzed.

COMPARISON OF SELECTED PHYSICAL PROPERTIES OF TESTED NANOSUSPENSIONS – THE RESULTS OF THE EXPERIMENTAL RESEARCH OF THE DEGREE OF SEDIMENTATION AND THE DEPTH OF PENETRATION IN REFERENCE MATERIALS IN LABORATORY CONDITIONS

Directory of Open Access Journals (Sweden)

Klára Kroftová

2017-10-01

Full Text Available Between used and already verified technologies for the reinforcement of plasters mainly include nanosuspension containing nanoparticles of calcium hydroxide and nanomaterials based on magnesium hydroxide and barium carbonate. Individual lime nanosuspension, which consists of nanoparticles of calcium hydroxide, are dispersed in an alcoholic environment and they differ from each concentration and type of alcohol. When the material is cured, carbonatation occurs, as well as in the case of fresh plaster, where the calcium hydroxide reacts with atmospheric carbon dioxide to produce calcium carbonate. Due to the deposition of calcium carbonate in the damaged material, occurs re-strengthened ties and its hardening. The undoubted advantage of the consolidation of plaster using nanolime is the low number of impregnation cycles, where after a few applications nanosuspension occurs to the reinforcement of degraded material.

Deactivation of nickel hydroxide-gold modified electrodes

OpenAIRE

Caram, Bruno; Tucceri, Ricardo

2013-01-01

The aim of the present work was to study how the charge-transport process of a nickel hydroxide film electrochemically synthesized on a gold substrate is modified when the electrode is stored for a long time. It was found that nickel hydroxide films are deactivated under storage, that is, films became less conductive than films immediately prepared (nondeactivated). This study was carried out in the context of the rotating disc electrode voltammetry when the modified electrode contacts an ele...

Influence of calcium and lithium on the densification and electrical conductivity of gadolinia-doped ceria

International Nuclear Information System (INIS)

Porfirio, Tatiane Cristina

2011-01-01

In this work, the use of calcium and lithium as sintering aid to gadolinia-doped ceria was systematically investigated. The main purpose was to verify the influence of these additives on the densification and electrical conductivity of sintered ceramics. Powder compositions containing up to 1.5 mol% (metal basis) of calcium or lithium were prepared by both solid state reaction and oxalate coprecipitation methods. The main characterization techniques were thermal analyses, X-ray diffraction, scanning electron microscopy and electrical conductivity by impedance spectroscopy. Both additives promoted densification of gadolinia-doped ceria. The densification increases with increasing the additive content. Different effects on microstructure and electrical conductivity result from the method of preparation, e.g., solid state reaction or coprecipitation. Calcium addition greatly enhances the grain growth compared to lithium addition. The electrical conductivity of specimens containing a second additive is lower than that of pure gadolinia-doped ceria. Both additives influence the intergranular conductivity and favor the exudation of gadolinium out of the solid solution. (author)

Textural and chemical characterizations of adsorbent prepared from palm shell by potassium hydroxide impregnation at different stages.

Science.gov (United States)

Guo, Jia; Lua, Aik Chong

2002-10-15

Preparation and characterization of activated carbon from palm shell, a carbonaceous agricultural solid waste, by potassium hydroxide treatment at different stages were studied. The effects of activation temperature and chemical to sample ratio on the characteristics of the activated carbon were investigated. Fixed-bed adsorption of sulfur dioxide (SO(2)) gas was carried out to evaluate the adsorptive capacity of the samples. Desorption tests were conducted to verify the occurrence of chemisorption due to some surface functional groups or of chemical reaction between SO(2) and KOH. It was found that pre-impregnation of raw palm shell was involved in replacement of some hydrogen ions with potassium ions to form cross-linked complexes, which retarded the tar formation during carbonization, resulting in a relatively high yield. Moreover, these potassium ions accelerated the reaction as catalysts during gasification of chars by carbon dioxide. For chars with mid-impregnation, potassium hydroxide acted in two ways: (i) formation of metallic potassium by dehydration and (ii) conversion into potassium carbonate. Metallic potassium intercalated to the carbon matrix accounted for pore development and potassium carbonate layer prevented the sample from over burn-off. Post-impregnation of final products modified the textural characteristics of the sample as some pore entrances were blocked by chemicals. However, potassium hydroxide enhanced the amount of SO(2) uptaken via formation of potassium sulfite.

Corrosion resistance of biomimetic calcium phosphate coatings on magnesium due to varying pretreatment time

Energy Technology Data Exchange (ETDEWEB)

Waterman, J., E-mail: jay.waterman@pg.canterbury.ac.nz [Department of Mechanical Engineering, University of Canterbury, Christchurch (New Zealand); Pietak, A. [Department of Anatomy and Structural Biology, University of Otago, Dunedin (New Zealand); Birbilis, N. [Department of Materials Engineering, Monash University (Australia); Woodfield, T. [Department of Mechanical Engineering, University of Canterbury, Christchurch (New Zealand); Department of Orthopaedic Surgery, University of Otago, Christchurch (New Zealand); Dias, G. [Department of Anatomy and Structural Biology, University of Otago, Dunedin (New Zealand); Staiger, M.P., E-mail: mark.staiger@canterbury.ac.nz [Department of Mechanical Engineering, University of Canterbury, Christchurch (New Zealand)

2011-12-15

Calcium phosphate coatings were prepared on magnesium substrates via a biomimetic coating process. The effects of a magnesium hydroxide pretreatment on the formation and the ultimate corrosion protection of the coatings were studied. The pretreatment layer was found to affect the amount of defects present in the coatings. Corrosion resistance of the coatings was studied in vitro using two simulated body fluids, 0.8% NaCl and Hanks solution. In NaCl, the resistance to corrosion of all samples decreases with time as corrosion proceeded through cracks and other defects in the coatings. Samples with no pretreatment displayed the highest corrosion resistance as these samples had the fewest defects in the coating. However, in Hanks solution, corrosion resistance increased with time due to additional nucleation of calcium phosphate from the fluid on to the substrate. In this solution, additional pretreatment time was beneficial to the overall corrosion resistance.

Arsenic removal from contaminated brackish sea water by sorption onto Al hydroxides and Fe phases mobilized by land-use.

Science.gov (United States)

Yu, Changxun; Peltola, Pasi; Nystrand, Miriam I; Virtasalo, Joonas J; Österholm, Peter; Ojala, Antti E K; Hogmalm, Johan K; Åström, Mats E

2016-01-15

This study examines the spatial and temporal distribution patterns of arsenic (As) in solid and aqueous materials along the mixing zone of an estuary, located in the south-eastern part of the Bothnian Bay and fed by a creek running through an acid sulfate (AS) soil landscape. The concentrations of As in solution form (<1 kDa) increase steadily from the creek mouth to the outer estuary, suggesting that inflowing seawater, rather than AS soil, is the major As source in the estuary. In sediments at the outer estuary, As was accumulated and diagenetically cycled in the surficial layers, as throughout much of the Bothnian Bay. In contrast, in sediments in the inner estuary, As concentrations and accumulation rates showed systematical peaks at greater depths. These peaks were overall consistent with the temporal trend of past As discharges from the Rönnskär smelter and the accompanied As concentrations in past sea-water of the Bothnian Bay, pointing to a connection between the historical smelter activities and the sediment-bound As in the inner estuary. However, the concentrations and accumulation rates of As peaked at depths where the smelter activities had already declined, but a large increase in the deposition of Al hydroxides and Fe phases occurred in response to intensified land-use in the mid 1960's and early 1970's. This correspondence suggests that, apart from the inflowing As-contaminated seawater, capture by Al hydroxides, Fe hydroxides and Fe-organic complexes is another important factor for As deposition in the inner estuary. After accumulating in the sediment, the solid-phase As was partly remobilized, as reflected by increased pore-water As concentrations, a process favored by As(V) reduction and high concentrations of dissolved organic matter. Copyright © 2015 Elsevier B.V. All rights reserved.

Luminescent materials based on Tb, Eu-containing layered double hydroxides

International Nuclear Information System (INIS)

Zhuravleva, N.G.; Eliseev, A.A.; Lukashin, A.V.; Kinast, U.; Tret'yakov, Yu.D.

2004-01-01

Luminescent materials on the basis of magnesium-aluminium layered double hydroxides with intercalated anionic complexes of terbium and europium picolinates were synthesized. Relying on data of spectroscopy, elementary and X-ray phase analyses, the change in the rare earth complex structure and metal/ligand ratio, depending on the hydroxide layer charge, determined by Mg/Al ratio in the double hydroxide, were ascertained. The values of quantum yields of luminescence for terbium-containing samples amounted to 30-50% [ru

Gas-Solid Reaction Properties of Fluorine Compounds and Solid Adsorbents for Off-Gas Treatment from Semiconductor Facility

Directory of Open Access Journals (Sweden)

Shinji Yasui

2012-01-01

Full Text Available We have been developing a new dry-type off-gas treatment system for recycling fluorine from perfluoro compounds present in off-gases from the semiconductor industry. The feature of this system is to adsorb the fluorine compounds in the exhaust gases from the decomposition furnace by using two types of solid adsorbents: the calcium carbonate in the upper layer adsorbs HF and converts it to CaF2, and the sodium bicarbonate in the lower layer adsorbs HF and SiF4 and converts them to Na2SiF6. This paper describes the fluorine compound adsorption properties of both the solid adsorbents—calcium carbonate and the sodium compound—for the optimal design of the fixation furnace. An analysis of the gas-solid reaction rate was performed from the experimental results of the breakthrough curve by using a fixed-bed reaction model, and the reaction rate constants and adsorption capacity were obtained for achieving an optimal process design.

Stabilization of ZnCl2-Containing Waste Using Calcium Sulfoaluminate Cement

International Nuclear Information System (INIS)

Cau Dit Coumes, C.; Berger, S.; Le Bescop, P.; Damidot, D.

2013-01-01

The potential of calcium sulfoaluminate (CSA) cement was investigated to solidify and stabilize radwastes containing large amounts of soluble zinc chloride (a strong inhibitor of Portland cement hydration). Hydration of pastes and mortars prepared with a 0.5 mol/L ZnCl 2 mixing solution was characterized over one year as a function of the gypsum content of the binder and the thermal history of the material. Blending the CSA clinker with 20% gypsum enabled rapid hydration, with only very small delay compared with a reference prepared with pure water. It also improved the compressive strength of the hardened material and significantly reduced its expansion under wet curing. Moreover, the hydrate assemblage was less affected by a thermal treatment at early age simulating the temperature rise and fall occurring in a large-volume drum of cemented waste. Fully hydrated materials contained ettringite, amorphous aluminum hydroxide, straetlingite, together with AFm phases (Kuzel's salt associated with monosulfoaluminate or Friedel's salt depending on the gypsum content of the binder), and possibly C-(A)-S-H. Zinc was readily insolubilized and could not be detected in the pore solution extracted from cement pastes, or in their leachates after 3 months of leaching by pure water at pH 7. The good retention of zinc by the cement matrix was mainly attributed to the precipitation of a hydrated and well crystallized phase with platelet morphology (which may belong to the layered double hydroxides family) at early age ≤ 1 day), and to chemisorption onto aluminum hydroxide at later age. (author)

Thermochemical properties of the alkali hydroxides: A review

International Nuclear Information System (INIS)

Konings, R.J.M.; Cordfunke, E.H.P.

1989-01-01

The formation of volatile alkali hydroxides as a result of high-temperature steam corrosion plays an important role in nuclear technology. For the modeling of the volatilization processes, reliable thermodynamic data are required. In the present paper recent physico-chemical experiments by the authors will be discussed and the thermochemical properties of the alkali hydroxide series will be evaluated. (orig.)

Distribution of cadmium between calcium carbonate and solution, 2

International Nuclear Information System (INIS)

Kitano, Yasushi; Kanamori, Nobuko; Fujiyoshi, Ryoko

1978-01-01

The distribution coefficient of cadmium between calcite and solution has been measured in the calcium bicarbonate solution containing cadmium and chloride ions, which forms complexes with cadmium ions. It has been confirmed experimentally that cadmium carbonate is present as a solid solution between calcitic calcium carbonate and cadmium carbonate in the carbonate precipitate formed in the solution system. However, the constant value of the thermodynamic distribution coefficient of cadmium between calcite and solution has not been obtained experimentally in the calcium bicarbonate solution containing cadmium and chloride ions. It may have been caused by the very specific behavior of cadmium ions, but the exact reason remains unsolved and must be studied. (Kobatake, H.)

Development of a degradable cement of calcium phosphate and calcium sulfate composite for bone reconstruction

International Nuclear Information System (INIS)

Guo, H; Wei, J; Liu, C S

2006-01-01

A new type of composite bone cement was prepared and investigated by adding calcium sulfate (CS) to calcium phosphate cement (CPC). This composite cement can be handled as a paste and easily shaped into any contour, which can set within 5-20 min, the setting time largely depending on the liquid-solid (L/S) ratio; adding CS to CPC had little effect on the setting time of the composite cements. No obvious temperature increase and pH change were observed during setting and immersion in simulated body fluid (SBF). The compressive strength of the cement decreased with an increase in the content of CS. The degradation rate of the composite cements increased with time when the CS content was more than 20 wt%. Calcium deficient apatite could form on the surface of the composite cement because the release of calcium into SBF from the dissolution of CS and the apatite of the cement induced the new apatite formation; increasing the content of CS in the composite could improve the bioactivity of the composite cements. The results suggested that composite cement has a reasonable setting time, excellent degradability and suitable mechanical strength and bioactivity, which shows promising prospects for development as a clinical cement

Potassium hydroxide: an alternative reagent to perform the modified apt test.

Science.gov (United States)

Chicaiza, Henry; Hellstrand, Karl; Lerer, Trudy; Smith, Sharon; Sylvester, Francisco

2014-09-01

We tested the performance of potassium hydroxide (KOH) in the modified Apt test under different experimental conditions using sodium hydroxide as a positive control. Like sodium hydroxide, KOH differentiated fresh fetal and adult blood stains on a cloth but not dried blood. KOH may be used to perform the Apt test at the bedside. Copyright © 2014 Elsevier Inc. All rights reserved.

Average formation number n-barOH of colloid-type indium hydroxide

International Nuclear Information System (INIS)

Stefanowicz, T.; Szent-Kirallyine Gajda, J.

1983-01-01

Indium perchlorate in perchloric acid solution was titrated with sodium hydroxide solution to various pH values. Indium hydroxide colloid was removed by ultracentrifugation and supernatant solution was titrated with base to neutral pH. The two-stage titration data were used to calculate the formation number of indium hydroxide colloid, which was found to equal n-bar OH = 2.8. (author)

DOUBLE-SHELL TANK (DST) HYDROXIDE DEPLETION MODEL FOR CARBON DIOXIDE ABSORPTION

International Nuclear Information System (INIS)

OGDEN DM; KIRCH NW

2007-01-01

This document generates a supernatant hydroxide ion depletion model based on mechanistic principles. The carbon dioxide absorption mechanistic model is developed in this report. The report also benchmarks the model against historical tank supernatant hydroxide data and vapor space carbon dioxide data. A comparison of the newly generated mechanistic model with previously applied empirical hydroxide depletion equations is also performed

Effect of calcium on adsorptive removal of As(III) and As(V) by iron oxide-based adsorbents

KAUST Repository

Uwamariya, V.

2014-06-25

The effects of calcium on the equilibrium adsorption capacity of As(III) and As(V) onto iron oxide-coated sand (IOCS) and granular ferric hydroxide (GFH) were investigated through batch experiments, rapid small-scale column tests (RSSCT) and kinetics modelling. Batch experiments showed that at calcium concentrations≤20 mg/L, high As(III) and As(V) removal efficiencies by IOCS and GFH are achieved at pH 6. An increase of the calcium concentration to 40 and 80 mg/L reversed this trend, giving higher removal efficiencies at higher pH (8). The adsorption capacities of IOCS and GFH at an equilibrium arsenic concentration of 10 g/L were found to be between 2.0 and 3.1 mg/g for synthetic water without calcium and between 2.8 and 5.3 mg/g when 80 mg/L of calcium was present at the studied pH values. After 10 hours of filter run in RSSCT, approximately 1000 empty bed volumes, the ratios of C/Co for As(V) were 26% and 18% for calcium-free model water; and only 1% and 0.2% after addition of 80 mg/L of Ca for filter columns with IOCS and GFH, respectively. The adsorption of As(III) and As(V) onto GFH follows a second-order reaction, with and without addition of calcium. The adsorption of As(III) and As(V) onto IOCS follows a first-order reaction without calcium addition, and moves to the second-reaction-order kinetics when calcium is added. Based on the intraparticle diffusion model, the main controlling mechanism for As(III) adsorption is intraparticle diffusion, while surface diffusion contributes greatly to the adsorption of As(V).

Demonstration of Entrained Solids and Sr/TRU Removal Processes with Archived AN-107 Waste

International Nuclear Information System (INIS)

Hallen, R.T.; Brooks, K.P.; Jagoda, L.K.

2000-01-01

Archived AN-107 waste was used to evaluate entrained solids removal, Sr/TRU decontamination of supernatant, and Sr/TRU solids removal. Even though most of the entrained solids had been previously removed from the archived sample, the residual entrained solids rapidly fouled the filter element resulting in very poor filter performance. An attempt to run at higher pressure resulted in more fouling, and reduced filter performance. Filtration efforts to remove entrained solids were abandoned and the waste was treated for Sr/TRU removal with the entrained solids present. The new processing scheme for Sr/TRU removal involving precipitation by added strontium and permanganate worked well. The decontamination factors for Sr and TRU components were significantly greater than the ILAW DF requirements for higher reagent concentrations of 1M hydroxide, 0.075M Sr, and 0.05M permanganate and lower reagent concentrations of 0.8M hydroxide, 0.05M Sr, and 0.03M permanganate. These results support the use of lower concentration of reagent additions in future tests. Optimization studies should be conducted to examine the reduction in added hydroxide from 1M to 0.5 M, reduction of Sr from 0.075M to 0.05M, and reduction in permanganate from 0.05M to 0.03M and the impact this reduction has on filtration performance with new samples from Tank AN-107. The combined entrained solids and Sr/TRU precipitate were successfully filtered in the single element, crossflow filtration unit. The filtrate flux was high, >0.1 gpm/ft 2 , at the initial test conditions of 53 psi and 11.2ft/s for the treated archived AN-107 sample. The filter flux rate dropped significantly with time as testing progressed and appears to be a result of shearing the agglomerated solids and fouling of the filter element by the resulting fine particles. The relatively low clean water flux rates obtained at the end of the test also indicate filter fouling. Chemical cleaning was required to restore clean water flux rates to pre

Adsorption Mechanisms of Trivalent Gold onto Iron Oxy-Hydroxides: From the Molecular Scale to the Model

International Nuclear Information System (INIS)

Cances, Benjamin; Benedetti, Marc; Farges, Francois; Brown, Gordon E. Jr.

2007-01-01

Gold is a highly valuable metal that can concentrate in iron-rich exogenetic horizons such as laterites. An improved knowledge of the retention mechanisms of gold onto highly reactive soil components such as iron oxy-hydroxides is therefore needed to better understand and predict the geochemical behavior of this element. In this study, we use EXAFS information and titration experiments to provide a realistic thermochemical description of the sorption of trivalent gold onto iron oxy-hydroxides. Analysis of Au LIII-edge XAFS spectra shows that aqueous Au(III) adsorbs from chloride solutions onto goethite surfaces as inner-sphere square-planar complexes (Au(III)(OH,Cl)4), with dominantly OH ligands at pH > 6 and mixed OH/Cl ligands at lower pH values. In combination with these spectroscopic results, Reverse Monte Carlo simulations were used to constraint the possible sorption sites on the surface of goethite. Based on this structural information, we calculated sorption isotherms of Au(III) on Fe oxy-hydroxides surfaces, using the CD-MUSIC (Charge Distribution - MUlti SIte Complexation) model. The various Au(III)-sorbed species were identified as a function of pH, and the results of these EXAFS+CD-MUSIC models are compared with titration experiments. The overall good agreement between the predicted and measured structural models shows the potential of this combined approach to better model sorption processes of transition elements onto highly reactive solid surfaces such as goethite and ferrihydrite

Physical-Mechanical Properties and Micromorphology of Calcium Cements Exposed to Polyacrylic and Phosphoric Acids.

Science.gov (United States)

de Souza, Gustavo Fernandes; Arrais, Ana Beatriz; Aragão, Cícero Flávio Soares; Ferreira, Isana Alvares; Borges, Boniek Castillo Dutra

2018-01-01

To evaluate if physical and mechanical properties of self-curing calcium hydroxide cements were affected by contact with polyacrylic and phosphoric acids. Resin-containing (Life (LF)) and resin-free (Hydro C (HyC)) materials were subjected to polyacrylic acid conditioning and rinsing (POL); phosphoric acid conditioning and rinsing (PHO); rinsing only; and no treatment ( n = 10). Water sorption/solubility, release of hydroxyl ions (pH), roughness (Ra), and impact resistance were evaluated. Additional samples ( n = 1) were prepared for scanning electron microscopy (SEM) analysis of the surface morphology. Data were analyzed by two-way ANOVA and Tukey post hoc test ( P < 0.05). Water sorption was significantly higher for LF when in contact with PHO and lower for POL ( P < 0.05). The mean solubility was higher with POL for both cements ( P < 0.05). PHO increased the mean surface roughness for HyC ( P < 0.01); a significant decrease was noted for LF after contact with both acids ( P < 0.01). PHO promoted lower release of hydroxyl ions on both cements ( P < 0.05). For LF, rinsing, PHO, and POL presented similar morphology, differing from the control group. For HyC, PHO and POL presented similar morphology, differing from the control group. PHO had a negative effect on the physical properties of the cements tested, except for the solubility test. POL affected roughness and solubility of HyC cement. Clinical procedures that require polyacrylic and phosphoric acid conditioning must be done carefully on self-curing calcium hydroxide cements in order to avoid negative impact on their properties.

HYDROGEN PEROXIDE BLEACHING OF CMP PULP USING MAGNESIUM HYDROXIDE

Directory of Open Access Journals (Sweden)

Farhad Zeinaly

2009-11-01

Full Text Available Conventional bleaching of hardwood CMP pulp with magnesium hydroxide (Mg(OH2 show significant benefits over bleaching with sodium hydroxide (NaOH under various conditions. Magnesium hydroxide bleaching generate higher optical properties, higher pulp yield and lower effluent COD at the same chemical charge, but the physical properties were found to be similar for both processes. The initial freeness of the bleached pulps and refining value to reach a target freeness (about 350 ml. CSF were more for the Mg(OH2-based process. The residual peroxide of filtrate from the Mg(OH2-based process was very high as compared to conventional bleaching.

A convenient procedure for the solid-phase synthesis of hydroxamic acids on PEGA resins

DEFF Research Database (Denmark)

Nandurkar, Nitin Subhash; Petersen, Rico; Qvortrup, Katrine

2011-01-01

An efficient method for the solid-phase synthesis of hydroxamic acids is described. The method comprises the nucleophilic displacement of esters immobilized on PEGA resins with hydroxylamine/sodium hydroxide in isopropanol. The hydroxyaminolysis protocol is compatible with a broad range of PEGA...

Comparative evaluation of platelet-rich fibrin, mineral trioxide aggregate, and calcium hydroxide as pulpotomy agents in permanent molars with irreversible pulpitis: A randomized controlled trial

Science.gov (United States)

Kumar, Varun; Juneja, Ruchi; Duhan, Jigyasa; Sangwan, Pankaj; Tewari, Sanjay

2016-01-01

Background: Pulpotomy has been proposed as an alternative for the management of irreversible pulpitis in permanent molars with closed apices. Aim: To compare the performances of calcium hydroxide (CH), mineral trioxide aggregate (MTA), and platelet-rich fibrin (PRF) as pulpotomy agents in mature permanent molars with irreversible pulpitis. Materials and Methods: Fifty-four permanent mandibular molars with carious exposure and symptoms of irreversible pulpitis were randomly allocated to three groups, and full pulpotomy was performed using CH, MTA, or PRF as pulpotomy agents. Pain intensity was recorded using numeric rating scale score at baseline, 24 h, 7 days, 6 months, and 1 year. Clinical and radiographic assessments were done at 6 months and 1 year. Statistical Analysis: Kruskal–Wallis test and Friedman test were used for intergroup and intragroup comparison of pain scores, respectively. The radiographic outcomes between the three study arms were compared using Chi-square test. Results: Clinical success rate was 94.4% at 7 days, which dropped to 85.4% at 12 months. All three agents were equally effective in providing pain relief at all the intervals tested, with no significant difference between them (P > 0.05 at all intervals). However, at 6 months and 12 months, 26.2% and 52.4% teeth depicted slight widening of periodontal ligament space. No significant difference was observed between the radiographic success rates observed with the three groups (P = 0.135 at 6 months, 0.717 at 12 months). Conclusion: Pulpotomy exhibited a high clinical success rate in mature molars with irreversible pulpitis and selection of biomaterial did not affect its outcome. PMID:27994420

The effectiveness of various chelates used alone or in combination with sodium hypochlorite in the removal of calcium hydroxide from root canals

Directory of Open Access Journals (Sweden)

Emel Uzunoglu

2015-01-01

Full Text Available Aim: To evaluate the effectiveness of various chelates used alone or in combination with sodium hypochlorite (NaOCl in the removal of calcium hydroxide (Ca(OH2 from root canals. Materials and Methods: The root canals of 72 mandibular incisors were prepared up to the ProTaper F2 file. Among these, six randomly selected teeth were used as negative and positive controls, while the root canals of the remaining 66 were filled with Ca(OH2 paste for 1 week. Then, the experimental group specimens were divided into six groups (n = 11. The access cavities were reopened and the Ca(OH2 paste in each group was removed using the following solutions: 2.5 mL ethylenediaminetetraacetic acid (EDTA; Group 1, 2.5 mL peracetic acid (PAA; Group 2, 2.5 mL QMix (Group 3, 2.5 mL NaOCl/2.5 mL EDTA (Group 4, 2.5 mL NaOCl/2.5 mL PAA (Group 5, and 2.5 mL NaOCl/2.5 mL QMix (Group 6. Digital photographs of longitudinally split specimens were imported into image analyzer software, and the amount of residual Ca (OH 2 was recorded as a percentage of the overall canal surface area. The results were analyzed using Kruskal–Wallis and Conover–Dunn tests. Results: The canal walls in the positive control group were completely covered with Ca(OH 2 compared with those in the negative control group. The lowest Ca(OH2 removal efficiency was observed for Group 4 (P < 0.001, while Group 6 showed favorable results (P < 0.05. Conclusions: QMix combined with NaOCl can remove Ca(OH2 from root canals as effectively as 17% EDTA and 1% PAA. The type and sequence of irrigants are more important than the total irrigant volume for effective Ca(OH 2 removal.

The study of the thermal behavior of solid mixtures of metakaolin and sodium hydroxide by isoconversional model-free analyzes

Science.gov (United States)

Gordina, Natalya E.; Prokof'ev, Valery Yu; Smirnov, Nikolay N.; Khramtsova, Alexandra P.

2017-11-01

Interactions in solid mixtures of 6Al2Si2O7: 12NaOH and 6Al2Si2O7: 12NaOH: 2Al2O3 under thermal treatment were studied. Ultrasonic pre-treatment of suspensions with a frequency of 22 kHz was applied. X-ray phase analysis, scanning electron microscopy, and synchronous thermal analysis were used in this research. It was shown that after evaporation of the suspensions, the hydrated LTA zeolite and sodium hydroaluminate are synthesized. During thermal treatment up to 500 °C, the adsorption water is removed first and then the dehydration of the zeolite and hydroaluminate occurs. Calcination at temperatures above 500° C leads to the synthesis of Na6Al4Si4O17 and Na8Al4Si4O18 by the interaction of metakaolin and zeolite with sodium hydroxide. At temperatures above 700 °C, the formation of mullite and nepheline occurs in the temperature range of 500-800 °C. The kinetic parameters have been calculated using Friedman analysis (differential method), Kissinger-Akahira-Sunose and Ozawa-Flynn-Wall analyzes (integral methods). It was shown that all analyzes give similar dependences of the apparent activation energy vs the conversion extent and the values of E are in the range of 70-350 kJ mol-1. It was established that ultrasonic pre-treatment allows to reduce the values of the apparent activation energy. It was discovered that the Al2O3 excess over the stoichiometry of the LTA zeolite synthesis is an inhibitor of the mullite and nepheline formation reactions.

Sorption of chromium(VI) and chromium(III) on aluminium hydroxide

International Nuclear Information System (INIS)

Music, S.

1986-01-01

Factors that influence the sorption of Cr(VI) and Cr(III) on aluminium hydroxide were investigated. The sorption of chromates decreases as the pH of the suspension increases. The mechanism of CrOsub(4)sup(2-) sorption was interpreted in terms of reactions between chromates and -OH and/or Hsub(2)O groups at the hydroxide/liquid interface. It was shown that chromates are more tightly sorbed on aluminium hydroxide compared to other anions, e.g. chlorides. On the other hand, specifically absorbed anions, such as molybdates, compete strongly with chromates for the sorption sites. The sorption of chromium(III) increases with the pH of the suspension. Also, the sorption of chromium(III) is suppressed in the presence of citrate ions. The best conditions for the fixation of Cr(VI) and Cr(III) by aluminium hydroxide are presented. (author)

Crystallite size effects in stacking faulted nickel hydroxide and its electrochemical behaviour

International Nuclear Information System (INIS)

Ramesh, T.N.

2009-01-01

β-Nickel hydroxide comprises a long range periodic arrangement of atoms with a stacking sequence of AC AC AC-having an ideal composition Ni(OH) 2 . Variation in the preparative conditions can lead to the changes in the stacking sequence (AC AC BA CB AC AC or AC AC AB AC AC). This type of variation in stacking sequence can result in the formation of stacking fault in nickel hydroxide. The stability of the stacking fault depends on the free energy content of the sample. Stacking faults in nickel hydroxide is essential for better electrochemical activity. Also there are reports correlating particle size to the better electrochemical activity. Here we present the effect of crystallite size on the stacking faulted nickel hydroxide samples. The electrochemical performance of stacking faulted nickel hydroxide with small crystallite size exchanges 0.8e/Ni, while the samples with larger crystallite size exchange 0.4e/Ni. Hence a right combination of crystallite size and stacking fault content has to be controlled for good electrochemical activity of nickel hydroxide

Synthesis of hydroxide type sorbents from industry high-iron wastes

International Nuclear Information System (INIS)

Stepanenko, E.K.; Smirnov, A.L.

1986-01-01

Article presents the results of studies on possibility of using of technological iron containing wastes for the obtaining of hydroxide type sorbents in granular form. The scheme of technology of synthesis of hydroxide type sorbents from high-iron wastes is elaborated.

Physical and chemical properties of calcium doped gadolinium cobaltite

International Nuclear Information System (INIS)

Zhuk, P.P.; Kharton, V.V.; Tonoyan, A.A.; Naumovich, E.N.

1991-01-01

The effect of calcium doping additions on electrical and tharmal properties of gadolinium cobaltite was investigated. It was established that solid solutions of Gd 1-x Ca x CoO 3 (x=0-0.5) composition had cubic perovskite structure with orthorhombic distortion. Calcium doping of gadolinium cobaltite increases its conductivity by two orders. Parameter of resistance of electronic layer of ρ/d for a sample of Gd 0.9 Ca 0.1 CoO 3 composition at d≥40mg/sm 2 was by an order higher than in compact samples

Palm oil trans-esterification with methanol via hetereogeneous catalysis

Directory of Open Access Journals (Sweden)

Julian Andrés Parra Garrido

2005-05-01

Full Text Available Four different solid catalyst' catalytic activity was studied in refined palm oil methanolysis: barium hydroxide, calcium oxide, magenesium oxide and tin oxide (IV. The last two presented low catalytic activity; they were thus discarded. The catalysts were used in powder form suspended in the reaction medium. HPLC was used for testing catalyic activity by measuring the glycerlo produced at the end of the reaction. Experiments were conducted at different pressures: 75 kPa (the pressure in Bogotá, 760 kPa, 1.800 kPa, 5.900 kPa and 11.400 kPa., 125°C (760 kPa and 160°C (1.800 kPa. Three different percentages of catalyser were assayed at 75 kPa and two experiments were done at very high pressure (10.9 psi around methanol's critical point (5.900 and 11.400 kPa. Both barium hidroxide and calcium oxide presented high catalytic activity. 75% - 80% conversion was obtained with them in 8-10 hours at 63.3°C and 1.5 and 3 hours using calcium oxide and barium hydroxide (respectively at high temperatures and pressures.

Adsorption of arsenic by activated carbon, calcium alginate and their composite beads.

Science.gov (United States)

Hassan, A F; Abdel-Mohsen, A M; Elhadidy, H

2014-07-01

The present investigation deals with preparation of three different adsorbent materials namely; potassium hydroxide activated carbon based apricot stone (C), calcium alginate beads (G) and calcium alginate/activated carbon composite beads (GC) were used for the removal of arsenic. The prepared adsorbent materials were characterized by scanning electron microscope (SEM), Fourier transform infrared spectroscopy (FTIR), N2-adsorption at -196°C and point of zero charge. From the obtained results, it was found that the porosity, surface area and total pore volume of the adsorbent material C>GC>G respectively, however, the G adsorbent has more acidic function group than the other adsorbents. The influence of pH, time, temperature and initial concentration of arsenic(V) were studied and optimized. GC exhibits the maximum As(V) adsorption (66.7mg/g at 30°C). The adsorption of arsenic ions was observed to follow pseudo-second order mechanism as well as the thermodynamic parameters confirm also the endothermic spontaneous and a physisorption process. Copyright © 2014 Elsevier B.V. All rights reserved.

Concentration of 99Tc in seawater by coprecipitation with iron hydroxide

International Nuclear Information System (INIS)

Momoshima, Noriyuki; Eto, Ichiro; Muhammad Sayad; Takashima, Yoshimasa

1991-01-01

A method for accumulation of 99 Tc in seawater has been developed. Technetium tracer in +VII oxidation state was added to the seawater together with reducing agent, potassium pyrosulfite, and coprecipitation agent, ferric chloride. After reduction of Tc(VII) at pH 4, Tc(IV) was coprecipitated as iron hydroxide by addition of sodium hydroxide to pH 9. The reduction and coprecipitation was quantitative and overall recovery of Tc was more than 98%. The green color of iron precipitate formed at pH 9 suggested that Tc(VII) as well as ferric ion was reduced under this condition. Adsorption of Tc(IV), however, was poor for iron hydroxide which was prepared in advance indicating active surface of freshly precipitated iron hydroxide is necessary for quantitative recovery of Tc(IV). A repeating coprecipitation technique was examined for enrichment of Tc in seawater that the same iron was used repeatedly as coprecipitater. After separation of iron hydroxide with Tc(IV) from supernatant, the precipitate was dissolved by addition of acid and then new seawater which contained reducing agent and Tc(VII) was added. Reduction and coprecipitation was again carried out. Good recovery was attained for 7 repeats. The proposed repeating coprecipitation technique was applicable to a large amount of seawater without increasing the amount of iron hydroxide which is subjected to radiochemical analysis. (author)

Aluminum Coprecipitates with Fe (hydr)oxides: Does Isomorphous Substitution of Al3plus for Fe3plus in Goethite Occur

Energy Technology Data Exchange (ETDEWEB)

E Bazilevskaya; D Archibald; M Aryanpour; J Kubicki; C Martinez

2011-12-31

Iron (hydr)oxides are common in natural environments and typically contain large amounts of impurities, presumably the result of coprecipitation processes. Coprecipitation of Al with Fe (hydr)oxides occurs, for example, during alternating reduction-oxidation cycles that promote dissolution of Fe from Fe-containing phases and its re-precipitation as Fe-Al (hydr)oxides. We used chemical and spectroscopic analyses to study the formation and transformation of Al coprecipitates with Fe (hydr)oxides. In addition, periodic density functional theory (DFT) computations were performed to assess the structural and energetic effects of isolated or clustered Al atoms at 8 and 25 mol% Al substitution in the goethite structure. Coprecipitates were synthesized by raising the pH of dilute homogeneous solutions containing a range of Fe and Al concentrations (100% Fe to 100% Al) to 5. The formation of ferrihydrite in initial suspensions with {<=}20 mol% Al, and of ferrihydrite and gibbsite in initial suspensions with {>=}25 mol% Al was confirmed by infrared spectroscopic and synchrotron-based X-ray diffraction analyses. While base titrations showed a buffer region that corresponded to the hydrolysis of Fe in initial solutions with {<=}25 mol% Al, all of the Al present in these solutions was retained by the solid phases at pH 5, thus indicating Al coprecipitation with the primary Fe hydroxide precipitate. In contrast, two buffer regions were observed in solutions with 30 mol% Al (at pH {approx}2.25 for Fe{sup 3+} and at pH {approx}4 for Al{sup 3+}), suggesting the formation of Fe and Al (hydr)oxides as two separate phases. The Al content of initial coprecipitates influenced the extent of ferrihydrite transformation and of its transformation products as indicated by the presence of goethite, hematite and/or ferrihydrite in aged suspensions. DFT experiments showed that: (i) optimized unit cell parameters for Al-substituted goethites (8 and 25 Mol% Al) in clustered arrangement (i.e., the

Kinetics of intercalation of fluorescent probes in magnesium–aluminium layered double hydroxide within a multiscale reaction–diffusion framework

Science.gov (United States)

Saliba, Daniel

2016-01-01

We report the synthesis of magnesium–aluminium layered double hydroxide (LDH) using a reaction–diffusion framework (RDF) that exploits the multiscale coupling of molecular diffusion with chemical reactions, nucleation and growth of crystals. In an RDF, the hydroxide anions are allowed to diffuse into an organic gel matrix containing the salt mixture needed for the precipitation of the LDH. The chemical structure and composition of the synthesized magnesium–aluminium LDHs are determined using powder X-ray diffraction (PXRD), thermo-gravimetric analysis, differential scanning calorimetry, solid-state nuclear magnetic resonance (SSNMR), Fourier transform infrared and energy dispersive X-ray spectroscopy. This novel technique also allows the investigation of the mechanism of intercalation of some fluorescent probes, such as the neutral three-dimensional rhodamine B (RhB) and the negatively charged two-dimensional 8-hydroxypyrene-1,3,6-trisulfonic acid (HPTS), using in situ steady-state fluorescence spectroscopy. The incorporation of these organic dyes inside the interlayer region of the LDH is confirmed via fluorescence microscopy, solid-state lifetime, SSNMR and PXRD. The activation energies of intercalation of the corresponding molecules (RhB and HPTS) are computed and exhibit dependence on the geometry of the involved probe (two or three dimensions), the charge of the fluorescent molecule (anionic, cationic or neutral) and the cationic ratio of the corresponding LDH. This article is part of the themed issue ‘Multiscale modelling at the physics–chemistry–biology interface’. PMID:27698034

Kinetics of intercalation of fluorescent probes in magnesium-aluminium layered double hydroxide within a multiscale reaction-diffusion framework

Science.gov (United States)

Saliba, Daniel; Al-Ghoul, Mazen

2016-11-01

We report the synthesis of magnesium-aluminium layered double hydroxide (LDH) using a reaction-diffusion framework (RDF) that exploits the multiscale coupling of molecular diffusion with chemical reactions, nucleation and growth of crystals. In an RDF, the hydroxide anions are allowed to diffuse into an organic gel matrix containing the salt mixture needed for the precipitation of the LDH. The chemical structure and composition of the synthesized magnesium-aluminium LDHs are determined using powder X-ray diffraction (PXRD), thermo-gravimetric analysis, differential scanning calorimetry, solid-state nuclear magnetic resonance (SSNMR), Fourier transform infrared and energy dispersive X-ray spectroscopy. This novel technique also allows the investigation of the mechanism of intercalation of some fluorescent probes, such as the neutral three-dimensional rhodamine B (RhB) and the negatively charged two-dimensional 8-hydroxypyrene-1,3,6-trisulfonic acid (HPTS), using in situ steady-state fluorescence spectroscopy. The incorporation of these organic dyes inside the interlayer region of the LDH is confirmed via fluorescence microscopy, solid-state lifetime, SSNMR and PXRD. The activation energies of intercalation of the corresponding molecules (RhB and HPTS) are computed and exhibit dependence on the geometry of the involved probe (two or three dimensions), the charge of the fluorescent molecule (anionic, cationic or neutral) and the cationic ratio of the corresponding LDH. This article is part of the themed issue 'Multiscale modelling at the physics-chemistry-biology interface'.

Synthesis of aluminum oxy-hydroxide nanofibers from porous anodic alumina

Energy Technology Data Exchange (ETDEWEB)

Jha, Himendra; Kikuchi, Tatsuya; Sakairi, Masatoshi; Takahashi, Hideaki [Laboratory of Interface Microstructure Analysis (LIMSA), Division of Materials Science and Engineering, Graduate School of Engineering, Hokkaido University, Sapporo 060-8628 (Japan)], E-mail: himendra@eng.hokudai.ac.jp

2008-10-01

A novel method for the synthesis of aluminum oxy-hydroxide nanofibers from a porous anodic oxide film of aluminum is demonstrated. In the present method, the porous anodic alumina not only acts as a template, but also serves as the starting material for the synthesis. The porous anodic alumina film is hydrothermally treated for pore-sealing, which forms aluminum oxy-hydroxide inside the pores of the oxide film as well as on the surface of the film. The hydrothermally sealed porous oxide film is immersed in the sodium citrate solution, which selectively etches the porous aluminum oxide from the film, leaving the oxy-hydroxide intact. The method is simple and gives highly uniform aluminum oxy-hydroxide nanofibers. Moreover, the diameter of the nanofibers can be controlled by controlling the pore size of the porous anodic alumina film, which depends on the anodizing conditions. Nanofibers with diameters of about 38-85 nm, having uniform shape and size, were successfully synthesized using the present method.

Synthesis of aluminum oxy-hydroxide nanofibers from porous anodic alumina

International Nuclear Information System (INIS)

Jha, Himendra; Kikuchi, Tatsuya; Sakairi, Masatoshi; Takahashi, Hideaki

2008-01-01

A novel method for the synthesis of aluminum oxy-hydroxide nanofibers from a porous anodic oxide film of aluminum is demonstrated. In the present method, the porous anodic alumina not only acts as a template, but also serves as the starting material for the synthesis. The porous anodic alumina film is hydrothermally treated for pore-sealing, which forms aluminum oxy-hydroxide inside the pores of the oxide film as well as on the surface of the film. The hydrothermally sealed porous oxide film is immersed in the sodium citrate solution, which selectively etches the porous aluminum oxide from the film, leaving the oxy-hydroxide intact. The method is simple and gives highly uniform aluminum oxy-hydroxide nanofibers. Moreover, the diameter of the nanofibers can be controlled by controlling the pore size of the porous anodic alumina film, which depends on the anodizing conditions. Nanofibers with diameters of about 38-85 nm, having uniform shape and size, were successfully synthesized using the present method

Enhanced tortuosity for electrolytes in microwave irradiated self-organized carbon-doped Ni/Co hydroxide nanocomposite electrodes with higher Ni/Co atomic ratio and rate capability for an asymmetric supercapacitor.

Science.gov (United States)

Kumar, Niraj; Kumar, Viresh; Panda, H S

2017-11-03

We demonstrate a green, facile and rapid microwave-mediated process for fabricating carbon black (CB) incorporated Ni/Co hydroxide porous nanocomposites and study the effect of various mass loading of CB on supercapacitor performance. The structure and interactions between CB and Ni/Co hydroxide are characterized by using x-ray diffraction, Fourier-transform infrared spectroscopy and x-ray photoelectron spectroscopy, which suggest the miniaturization of the single-phase Ni/Co hydroxide formation time. A morphology study reveals that the addition of CB into Ni/Co hydroxide develops a loose network structure with well-defined architectural pores. In addition, the nanocomposites demonstrate noticeable improvements in porosity and atomic ratio of Ni/Co with an increasing percentage of carbon, which results in a higher diffusion of electrolytes, and hence electrical conduction. The developed electrode materials exhibit a maximum specific capacitance value of 1526 Fg -1 at current density 1 Ag -1 with excellent cyclic stability (92% retention at 5000 cycles), energy density (76 Wh Kg -1 ), power density (250 W Kg -1 ) and rate capability. A solid state asymmetric supercapacitor device is fabricated and utilized to brighten a commercial LED effectively for validating real usage.

Enhanced tortuosity for electrolytes in microwave irradiated self-organized carbon-doped Ni/Co hydroxide nanocomposite electrodes with higher Ni/Co atomic ratio and rate capability for an asymmetric supercapacitor

Science.gov (United States)

Kumar, Niraj; Kumar, Viresh; Panda, H. S.

2017-11-01

We demonstrate a green, facile and rapid microwave-mediated process for fabricating carbon black (CB) incorporated Ni/Co hydroxide porous nanocomposites and study the effect of various mass loading of CB on supercapacitor performance. The structure and interactions between CB and Ni/Co hydroxide are characterized by using x-ray diffraction, Fourier-transform infrared spectroscopy and x-ray photoelectron spectroscopy, which suggest the miniaturization of the single-phase Ni/Co hydroxide formation time. A morphology study reveals that the addition of CB into Ni/Co hydroxide develops a loose network structure with well-defined architectural pores. In addition, the nanocomposites demonstrate noticeable improvements in porosity and atomic ratio of Ni/Co with an increasing percentage of carbon, which results in a higher diffusion of electrolytes, and hence electrical conduction. The developed electrode materials exhibit a maximum specific capacitance value of 1526 Fg-1 at current density 1 Ag-1 with excellent cyclic stability (92% retention at 5000 cycles), energy density (76 Wh Kg-1), power density (250 W Kg-1) and rate capability. A solid state asymmetric supercapacitor device is fabricated and utilized to brighten a commercial LED effectively for validating real usage.

Antimicrobial activity and pH of a endodontic sealer containing MTA

DEFF Research Database (Denmark)

Maliza, Amanda GA; de Andrade, Flaviana Bombarda; Arias, Marcela C

Objective: To investigate the antimicrobial activity, calcium release, and pH of a new mineral trioxide aggregate endodontic sealer when compared to endodontic sealers containing calcium hydroxide and/or epoxy resin. Method: Specimens were fabricated from MTA Fillapex, Sealer 26, Sealapex, and AH...... Plus immediately, 24 or 48 hours prior to the tests. The antimicrobial activity against Enterococcus faecalis and Candida albicans was evaluated by the direct contact and the agar diffusion methods. Calcium release was determined by atomic absorption spectrometry. The pH from solutions containing...... in solution with an alkaline pH. Conclusion: The new mineral trioxide aggregate endodontic sealer presented higher antimicrobial activity when compared to the sealers containing calcium hydroxide and/or epoxy resin. As for pH and calcium release, the sealers containing calcium hydroxide resulted in presented...

Preparation and structure of carbonated calcium hydroxyapatite substituted with heavy rare earth ions

Energy Technology Data Exchange (ETDEWEB)

Yasukawa, Akemi, E-mail: yasukawa@cc.hirosaki-u.ac.jp [School of Home Economics, Faculty of Education, Hirosaki University, 1-bunkyo, Hirosaki, Aomori 036-8560 (Japan); Kandori, Kazuhiko [School of Chemistry, Osaka University of Education, 4-698-1 Asahigaoka, Kashiwara, Osaka 582-8582 (Japan); Tanaka, Hidekazu [Department of Material Science, Faculty of Science and Engineering, Shimane University, 1060 Nishikawatsu, Matsue, Shimane 690-8504 (Japan); Gotoh, Keiko [Faculty of Human Life and Environment, Nara Women' s University, Kita-uoya-nishi, Nara 630-8506 (Japan)

2012-05-15

Highlights: Black-Right-Pointing-Pointer LnCaHap solid solution particles were prepared using five types of heavy rare earth ions by a precipitation method. Black-Right-Pointing-Pointer The length and the crystallinity of the LnCaHap particles first increased and then decreased with increasing Ln{sup 3+} contents. Black-Right-Pointing-Pointer A series of YCaHap solid solution particles formed with Y/(Y + Ca) = 0-0.10 were investigated using various methods in detail. -- Abstract: Calcium hydroxyapatite (CaHap) particles substituted five types of heavy rare earth ions (Ln: Y{sup 3+}, Gd{sup 3+}, Dy{sup 3+}, Er{sup 3+} and Yb{sup 3+}) were synthesized using a precipitation method and characterized using various means. These Ln ions strongly affected the crystal phases and the structures of the products. With increasing Ln/(Ln + Ca) in the starting solution ([X{sub Ln}]), the length and the crystallinity of the particles first increased and then decreased. The rare earth metal-calcium hydroxyapatite (LnCaHap) solid solution particles were obtained at [X{sub Y}] {<=} 0.10 for substituting Y system and at [X{sub Ln}] {<=} 0.01-0.03 for substituting the other Ln systems. LnPO{sub 4} was mixed with LnCaHap at higher [X{sub Ln}] for all Ln systems. A series of yttrium-calcium hydroxyapatite (YCaHap) solid solutions with [X{sub Y}] = 0-0.10 were investigated using XRD, TEM, ICP-AES, IR and TG-DTA in detail.

Preparation and structure of carbonated calcium hydroxyapatite substituted with heavy rare earth ions

International Nuclear Information System (INIS)

Yasukawa, Akemi; Kandori, Kazuhiko; Tanaka, Hidekazu; Gotoh, Keiko

2012-01-01

Highlights: ► LnCaHap solid solution particles were prepared using five types of heavy rare earth ions by a precipitation method. ► The length and the crystallinity of the LnCaHap particles first increased and then decreased with increasing Ln 3+ contents. ► A series of YCaHap solid solution particles formed with Y/(Y + Ca) = 0–0.10 were investigated using various methods in detail. -- Abstract: Calcium hydroxyapatite (CaHap) particles substituted five types of heavy rare earth ions (Ln: Y 3+ , Gd 3+ , Dy 3+ , Er 3+ and Yb 3+ ) were synthesized using a precipitation method and characterized using various means. These Ln ions strongly affected the crystal phases and the structures of the products. With increasing Ln/(Ln + Ca) in the starting solution ([X Ln ]), the length and the crystallinity of the particles first increased and then decreased. The rare earth metal-calcium hydroxyapatite (LnCaHap) solid solution particles were obtained at [X Y ] ≤ 0.10 for substituting Y system and at [X Ln ] ≤ 0.01–0.03 for substituting the other Ln systems. LnPO 4 was mixed with LnCaHap at higher [X Ln ] for all Ln systems. A series of yttrium-calcium hydroxyapatite (YCaHap) solid solutions with [X Y ] = 0–0.10 were investigated using XRD, TEM, ICP-AES, IR and TG–DTA in detail.

Calcium paradox and calcium entry blockers

NARCIS (Netherlands)

Ruigrok, T.J.C.; Slade, A.M.; Nayler, W.G.; Meijler, F.L.

1984-01-01

Reperfusion of isolated hearts with calcium-containing solution after a short period of calcium-free perfusion results in irreversible cell damage (calcium paradox). This phenomenon is characterized by an excessive influx of calcium into the cells, the rapid onset of myocardial contracture,

Formation of crystalline Zn-Al layered double hydroxide precipitates on γ-alumina: the role of mineral dissolution.

Science.gov (United States)

Li, Wei; Livi, Kenneth J T; Xu, Wenqian; Siebecker, Matthew G; Wang, Yujun; Phillips, Brian L; Sparks, Donald L

2012-11-06

To better understand the sequestration of toxic metals such as nickel (Ni), zinc (Zn), and cobalt (Co) as layered double hydroxide (LDH) phases in soils, we systematically examined the presence of Al and the role of mineral dissolution during Zn sorption/precipitation on γ-Al(2)O(3) (γ-alumina) at pH 7.5 using extended X-ray absorption fine structure spectroscopy (EXAFS), high-resolution transmission electron microscopy (HR-TEM), synchrotron-radiation powder X-ray diffraction (SR-XRD), and (27)Al solid-state NMR. The EXAFS analysis indicates the formation of Zn-Al LDH precipitates at Zn concentration ≥0.4 mM, and both HR-TEM and SR-XRD reveal that these precipitates are crystalline. These precipitates yield a small shoulder at δ(Al-27) = +12.5 ppm in the (27)Al solid-state NMR spectra, consistent with the mixed octahedral Al/Zn chemical environment in typical Zn-Al LDHs. The NMR analysis provides direct evidence for the existence of Al in the precipitates and the migration from the dissolution of γ-alumina substrate. To further address this issue, we compared the Zn sorption mechanism on a series of Al (hydr)oxides with similar chemical composition but differing dissolubility using EXAFS and TEM. These results suggest that, under the same experimental conditions, Zn-Al LDH precipitates formed on γ-alumina and corundum but not on less soluble minerals such as bayerite, boehmite, and gibbsite, which point outs that substrate mineral surface dissolution plays an important role in the formation of Zn-Al LDH precipitates.

Chemical looping coal gasification with calcium ferrite and barium ferrite via solid–solid reactions

International Nuclear Information System (INIS)

Siriwardane, Ranjani; Riley, Jarrett; Tian, Hanjing; Richards, George

2016-01-01

Highlights: • BaFe 2 O 4 and CaFe 2 O 4 are excellent for chemical looping coal gasification. • BaFe 2 O 4 and CaFe 2 O 4 have minimal reactivity with synthesis gas. • Steam enhances the gasification process with these oxygen carriers. • Reaction rates of steam gasification of coal with CaFe 2 O 4 was better than with gaseous oxygen. • Coal gasification appears to be via solid–solid interaction with the oxygen carrier. - Abstract: Coal gasification to produce synthesis gas by chemical looping was investigated with two oxygen carriers, barium ferrite (BaFe 2 O 4 ) and calcium ferrite (CaFe 2 O 4 ). Thermo-gravimetric analysis (TGA) and fixed-bed flow reactor data indicated that a solid–solid interaction occurred between oxygen carriers and coal to produce synthesis gas. Both thermodynamic analysis and experimental data indicated that BaFe 2 O 4 and CaFe 2 O 4 have high reactivity with coal but have a low reactivity with synthesis gas, which makes them very attractive for the coal gasification process. Adding steam increased the production of hydrogen (H 2 ) and carbon monoxide (CO), but carbon dioxide (CO 2 ) remained low because these oxygen carriers have minimal reactivity with H 2 and CO. Therefore, the combined steam–oxygen carrier produced the highest quantity of synthesis gas. It appeared that neither the water–gas shift reaction nor the water splitting reaction promoted additional H 2 formation with the oxygen carriers when steam was present. Wyodak coal, which is a sub-bituminous coal, had the best gasification yield with oxygen carrier–steam while Illinois #6 coal had the lowest. The rate of gasification and selectivity for synthesis gas production was significantly higher when these oxygen carriers were present during steam gasification of coal. The rates and synthesis gas yields during the temperature ramps of coal–steam with oxygen carriers were better than with gaseous oxygen.

A strategy of precipitated calcium carbonate (CaCO3) fillers for enhancing the mechanical properties of polypropylene polymers

International Nuclear Information System (INIS)

Thenepalli, Thriveni; Ahn, Ji Whan; Ahn, Young Jun; Han, Choon; Ramakrishna, Chilakala

2015-01-01

A wide variety of fillers are currently used in more than twenty types of polymer resins, although four of them alone (polypropylene, polyamides, thermoplastic polyesters, and polyvinyl chloride) account for 90% of the market of mineral fillers in plastics. Polypropylene (PP) and PVC dominate the market for calcium carbonate. PP is a versatile reinforcement material that can meet engineering and structural specifications and is widely used for automotive components, home appliances, and industrial applications. Talc, mica, clay, kaolin, wollastonite, calcium carbonates, feldspar, aluminum hydroxide, glass fibers, and natural fibers are commonly used in fillers. Among these, calcium carbonate (both natural and synthetic) is the mos abundant and affords the possibility of improved surface finishing, control over the manufacture of products, and increased electric resistance and impact resistance. Meeting the global challenge to reduce the weight of vehicles by using plastics is a significant issue. The current the global plastic and automobile industry cannot survive without fillers, additives, and reinforcements. Polypropylene is a major component of the modern plastic industry, and currently is used in dashboards, wheel covers, and some engine parts in automobiles. This article reports that the use of calcium carbonate fillers with polypropylene is the best choice to enhance the mechanical properties of plastic parts used in automobiles

Utilization of municipal solid waste incineration (MSWI) fly ash in blended cement

International Nuclear Information System (INIS)

Aubert, J.E.; Husson, B.; Sarramone, N.

2006-01-01

This paper is the first of a series of two articles dealing with the processes applied to MSWI fly ash with a view to reusing it safely in cement-based materials. Part 1 presents two stabilization processes and Part 2 deals with the use of the two treated fly ashes (TFA) in mortars. Two types of binder were used: an Ordinary Portland Cement (OPC) containing more than 95% clinker (CEM I 52.5R) and a binary blend cement composed of 70% ground granulated blast furnace slag and 30% clinker (CEM III-B 42.5N). In this first part, two stabilization processes are presented: the conventional process, called 'A', based on the washing, phosphation and calcination of the ash, and a modified process, called 'B', intended to eliminate metallic aluminum and sulfate contained in the ash. The physical, chemical and mineralogical characteristics of the two TFA were comparable. The main differences observed were those expected, i.e. TFA-B was free of metallic aluminum and sulfate. The mineralogical characterization of the two TFAs highlighted the presence of large amounts of a calcium aluminosilicate phase taking two forms, a crystalline form (gehlenite) and an amorphous form. Hydration studies on pastes containing mixed TFA and calcium hydroxide showed that this phase reacted with calcium hydroxide to form calcium aluminate hydrates. This formation of hydrates was accompanied by a hardening of the pastes. These results are very encouraging for the reuse of such TFA in cement-based materials because they can be considered as pozzolanic additions and could advantageously replace a part of the cement in cement-based materials. Finally, leaching tests were carried out to evaluate the environmental impact of the two TFAs. The elements which were less efficiently stabilized by process A were zinc, cadmium and antimony but, when the results of the leaching tests were compared with the thresholds of the European landfill directive, TFA-A could nevertheless be accepted at landfills for non

Utilization of municipal solid waste incineration (MSWI) fly ash in blended cement

Energy Technology Data Exchange (ETDEWEB)

Aubert, J.E. [Laboratoire Materiaux et Durabilite des Constructions (L.M.D.C.), INSA-UPS, 135 avenue de Rangueil, 31077 Toulouse cedex 4 (France)]. E-mail: aubert@insa-toulouse.fr; Husson, B. [Laboratoire Materiaux et Durabilite des Constructions (L.M.D.C.), INSA-UPS, 135 avenue de Rangueil, 31077 Toulouse cedex 4 (France); Sarramone, N. [Laboratoire Materiaux et Durabilite des Constructions (L.M.D.C.), INSA-UPS, 135 avenue de Rangueil, 31077 Toulouse cedex 4 (France)

2006-08-25

This paper is the first of a series of two articles dealing with the processes applied to MSWI fly ash with a view to reusing it safely in cement-based materials. Part 1 presents two stabilization processes and Part 2 deals with the use of the two treated fly ashes (TFA) in mortars. Two types of binder were used: an Ordinary Portland Cement (OPC) containing more than 95% clinker (CEM I 52.5R) and a binary blend cement composed of 70% ground granulated blast furnace slag and 30% clinker (CEM III-B 42.5N). In this first part, two stabilization processes are presented: the conventional process, called 'A', based on the washing, phosphation and calcination of the ash, and a modified process, called 'B', intended to eliminate metallic aluminum and sulfate contained in the ash. The physical, chemical and mineralogical characteristics of the two TFA were comparable. The main differences observed were those expected, i.e. TFA-B was free of metallic aluminum and sulfate. The mineralogical characterization of the two TFAs highlighted the presence of large amounts of a calcium aluminosilicate phase taking two forms, a crystalline form (gehlenite) and an amorphous form. Hydration studies on pastes containing mixed TFA and calcium hydroxide showed that this phase reacted with calcium hydroxide to form calcium aluminate hydrates. This formation of hydrates was accompanied by a hardening of the pastes. These results are very encouraging for the reuse of such TFA in cement-based materials because they can be considered as pozzolanic additions and could advantageously replace a part of the cement in cement-based materials. Finally, leaching tests were carried out to evaluate the environmental impact of the two TFAs. The elements which were less efficiently stabilized by process A were zinc, cadmium and antimony but, when the results of the leaching tests were compared with the thresholds of the European landfill directive, TFA-A could nevertheless be accepted at

Synthesis of modified calcium aluminate with lanthanum manganite (LSM) for possible use in solid oxide fuel cell (SOFC)

International Nuclear Information System (INIS)

Veiga, F.C.T.; Jurado, J.; Sousa, V.C. de

2016-01-01

The fuel cells solid oxide (SOFC) is made up of three basic elements: two electrodes, the anode and cathode and a conductive electrolyte ions. The objective of this work consists of calcium aluminate synthesis modified LSM in a 1: 1 by combustion synthesis method with a view to its use as a cathode in SOFC. The characterization of the post was carried out by the methods of XRD, TEM and EIS. After heat treatment at 1200°C/4 hours it was possible to obtain Ca0.5Sr1.5MnO4 and CaMnO2.56 phases. The material showed a semiconductor characteristics because with increasing temperature the electrical resistance value tends to decrease obtaining electrical conductivity greater than 10-6S / cm featuring an extrinsic semiconductor with an activation energy of 0.12. Therefore, with an activation energy value within the range of materials used for a SOFC cathodes. (author)

Preparation of a sinterable beryllium oxide through decomposition of beryllium hydroxide (1963)

International Nuclear Information System (INIS)

Bernier, M.

1963-01-01

In the course of the present study, we have attempted to precise the factors which among the ones effective in the course of the preparation of the beryllium hydroxide and oxide and during the sintering have an influence on the final result: the density and homogeneity of the sintered body. Of the several varieties of hydroxides precipitated from a sulfate solution the β-hydroxide only is always contaminated with beryllium sulfate and cannot be purified even by thorough washing. We noticed that those varieties of the hydroxide (gel, α, β) have different decomposition rates; this behaviour is used to identify and even to dose the different species in (α, β) mixtures. The various hydroxides transmit to the resulting oxides the shape they had when precipitated. Accordingly the history of the oxide is revealed by its behaviour during its fabrication and sintering. By comparing the results of the sintering operation with the various measurements performed on the oxide powders we are led to the conclusion that an oxide obtained from beryllium hydroxide is sinterable under vacuum if the following conditions are fulfilled: the particle size must lie between 0.1 and 0.2 μ and the BeSO 4 content of the powder must be less than 0.25 per cent wt (expressed as SO 3 /BeO). The best fitting is obtained with the oxide issued from an α-hydroxide precipitated as very small aggregates and with a low sulfur-content. We have observed that this is also the case for the oxide obtained by direct calcination of beryllium sulfate. (author) [fr

Functionalization of lanthanum hydroxide nanowires by atom transfer radical polymerization

International Nuclear Information System (INIS)

Zhou Mi; Yuan Jinying; Yuan Weizhong; Yin Yingwu; Hong Xiaoyin

2007-01-01

Atom transfer radical polymerization (ATRP) has been used to prepare a core-shell hybrid nanostructure successfully: a hard core of single-crystalline lanthanum hydroxide nanowires and a soft shell of polystyrene (PS) brushes. Transmission electron microscopy (TEM) images indicated that the resulting products presented special structures and different thicknesses of polymer layers. The chemical components and grafted PS quantities of the samples were measured by Fourier transform infrared (FT-IR) spectroscopy and thermogravimetric analysis (TGA). The polymers showed narrow polydispersity, which proved that the lanthanum hydroxide nanowires initiated the 'living'/controlled polymerization of styrene. With the modifiability of lanthanum hydroxide nanowires, the solubility increased, which affords a new way to functionalize nanowires

Structural perturbation of diphtheria toxoid upon adsorption to aluminium hydroxide adjuvant

NARCIS (Netherlands)

Regnier, M.; Metz, B.; Tilstra, W.; Hendriksen, C.; Jiskoot, W.; Norde, W.; Kersten, G.

2012-01-01

Aluminium-containing adjuvants are often used to enhance the potency of vaccines. In the present work we studied whether adsorption of diphtheria toxoid to colloidal aluminium hydroxide induces conformational changes of the antigen. Diphtheria toxoid has a high affinity for the aluminium hydroxide

Determination of basic state parameters and characterization of optical, dielectric and fluorescence properties of calcium boro lactate (CaBL)

International Nuclear Information System (INIS)

Vijayalakshmi, A.; Balraj, V.

2016-01-01

This paper describes the calculation of basic solid state parameters like penn gap, plasma energy, polarizability and fermi energy for calcium boro lactate single crystal. calcium boro lactate crystals were developed by solution growth method. Single crystal diffraction studies carried out and calculated basic solid state criterion for the CaBL compound. optical nature of these compound explained by using UV-Visible spectrum. Electro-optic behaviour of the crystal explained by dielectric studies. Light emitting properties explained by fluorescence studies. (author)

Synthesis of Zn–Fe layered double hydroxides via an oxidation process and structural analysis of products

Energy Technology Data Exchange (ETDEWEB)

Morimoto, Kazuya, E-mail: kazuya.morimoto@aist.go.jp [Institute for Geo-Resources and Environment, National Institute of Advanced Industrial Science and Technology (AIST), 1-1-1 Higashi, Tsukuba, Ibaraki 305-8567 (Japan); Tamura, Kenji [Environmental Remediation Materials Unit, National Institute for Materials Science (NIMS), 1-1 Namiki, Tsukuba, Ibaraki 305-0044 (Japan); Anraku, Sohtaro [Graduate School of Engineering, Hokkaido University, Kita 13 Nishi 8, Kita-ku, Sapporo 060-8628 (Japan); Sato, Tsutomu [Faculty of Engineering, Hokkaido University, Kita 13 Nishi 8, Kita-ku, Sapporo 060-8628 (Japan); Suzuki, Masaya [Institute for Geo-Resources and Environment, National Institute of Advanced Industrial Science and Technology (AIST), 1-1-1 Higashi, Tsukuba, Ibaraki 305-8567 (Japan); Yamada, Hirohisa [Environmental Remediation Materials Unit, National Institute for Materials Science (NIMS), 1-1 Namiki, Tsukuba, Ibaraki 305-0044 (Japan)

2015-08-15

The synthesis of Zn–Fe(III) layered double hydroxides was attempted, employing different pathways using either Fe(II) or Fe(III) species together with Zn as the initial reagents. The product derived from the synthesis employing Fe(II) was found to transition to a Zn–Fe(III) layered double hydroxides phase following oxidation process. In contrast, the product obtained with Fe(III) did not contain a layered double hydroxides phase, but rather consisted of simonkolleite and hydrous ferric oxide. It was determined that the valency of the Fe reagent used in the initial synthesis affected the generation of the layered double hydroxides phase. Fe(II) species have ionic radii and electronegativities similar to those of Zn, and therefore are more likely to form trioctahedral hydroxide layers with Zn species. - Graphical abstract: The synthesis of Zn–Fe(III) layered double hydroxides was attempted, employing different pathways using either Fe(II) or Fe(III) species together with Zn as the initial reagents. - Highlights: • Iron valency affected the generation of Zn–Fe layered double hydroxides. • Zn–Fe layered double hydroxides were successfully synthesized using Fe(II). • Fe(II) species were likely to form trioctahedral hydroxide layers with Zn species.

Nanostructural Deformation Analysis of Calcium Silicate Hydrate in Portland Cement Paste by Atomic Pair Distribution Function

Directory of Open Access Journals (Sweden)

Hiroshi Suzuki

2016-01-01

Full Text Available The deformation of nanostructure of calcium silicate hydrate (C-S-H in Portland cement (PC paste under compression was characterized by the atomic pair distribution function (PDF, measured using synchrotron X-ray diffraction. The PDF of the PC paste exhibited a unique deformation behavior for a short-range order below 2.0 nm, close to the size of the C-S-H globule, while the deformation for a long-range order was similar to that of a calcium hydroxide phase measured by Bragg peak shift. The compressive deformation of the C-S-H nanostructure was comprised of three stages with different interactions between globules. This behavior would originate from the granular nature of C-S-H, which deforms with increasing packing density by slipping the interfaces between globules, rearranging the overall C-S-H nanostructure. This new approach will lead to increasing applications of the PDF technique to understand the deformation mechanism of C-S-H in PC-based materials.

Vibrational dynamics of aqueous hydroxide solutions probed using broadband 2DIR spectroscopy

International Nuclear Information System (INIS)

Mandal, Aritra; Tokmakoff, Andrei

2015-01-01

We employed ultrafast transient absorption and broadband 2DIR spectroscopy to study the vibrational dynamics of aqueous hydroxide solutions by exciting the O–H stretch vibrations of the strongly hydrogen-bonded hydroxide solvation shell water and probing the continuum absorption of the solvated ion between 1500 and 3800 cm −1 . We observe rapid vibrational relaxation processes on 150–250 fs time scales across the entire probed spectral region as well as slower vibrational dynamics on 1–2 ps time scales. Furthermore, the O–H stretch excitation loses its frequency memory in 180 fs, and vibrational energy exchange between bulk-like water vibrations and hydroxide-associated water vibrations occurs in ∼200 fs. The fast dynamics in this system originate in strong nonlinear coupling between intra- and intermolecular vibrations and are explained in terms of non-adiabatic vibrational relaxation. These measurements indicate that the vibrational dynamics of the aqueous hydroxide complex are faster than the time scales reported for long-range transport of protons in aqueous hydroxide solutions

Variation in photoreactivity of iron hydroxides taken from an acidic mountain stream

International Nuclear Information System (INIS)

Hrncir, D.C.; McKnight, D.

1998-01-01

The photoreduction of iron hydroxides is known to exert significant influence over many biogeochemical processes in streams impacted by acid main drainage. Using laboratory and in-stream measurements, the variation in reactivity of iron hydroxides taken from a stream receiving acid mine drainage (AMD) was studied. The reactivity decreased for material collected at sites progressively downstream from the AMD inflow. In the presence of two simple organic ligands, photoreduction increased for the fresher iron hydroxides but remained unchanged for the older hydroxides. The importance of ligand coordination to the enhancement of photoreduction in natural waters was further demonstrated in experiments using two types of fulvic acids. In-stream measurements of hydrogen peroxide concentration are consistent with the conclusions drawn from the batch experiments. Iron hydroxides were observed to age over time, becoming less photoreactive. This aging was accompanied by an increase in crystallinity. The loss of photoreactivity for the older material can be explained by a decrease in the number of active surface sites, a change in the nature of the surface sites, or a combination of both

A model of propagating calcium-induced calcium release mediated by calcium diffusion

NARCIS (Netherlands)

Backx, P. H.; de Tombe, P. P.; van Deen, J. H.; Mulder, B. J.; ter Keurs, H. E.

1989-01-01

The effect of sudden local fluctuations of the free sarcoplasmic [Ca++]i in cardiac cells on calcium release and calcium uptake by the sarcoplasmic reticulum (SR) was calculated with the aid of a simplified model of SR calcium handling. The model was used to evaluate whether propagation of calcium

Efficacy and safety of topical application of 15% and 10% potassium hydroxide for the treatment of Molluscum contagiosum.

Science.gov (United States)

Teixidó, Concepció; Díez, Olga; Marsal, Josep R; Giner-Soriano, Maria; Pera, Helena; Martinez, Mireia; Galindo-Ortego, Gisela; Schoenenberger, Joan A; Real, Jordi; Cruz, Ines; Morros, Rosa

2018-02-26

Molluscum contagiosum is the most common skin infection in children. One topical treatment used for Molluscum contagiosum is potassium hydroxide. The objective of this study was to compare the efficacy of potassium hydroxide topical treatment at different concentrations with that of placebo in terms of complete clearing of Molluscum contagiosum lesions and to assess the safety and tolerance of potassium hydroxide topical treatment. This was a double-blind randomized clinical trial of three treatments (potassium hydroxide 10%, potassium hydroxide 15%, placebo) applied once daily up to complete clearing of lesions (maximum duration 60 days) in 53 children aged 2-6 years in primary health care pediatric offices in Catalonia, Spain. In the intention-to-treat analysis, potassium hydroxide 10% (58.8%, P = .03) and potassium hydroxide 15% (64.3%, P = .02) had efficacy superior to that of placebo (18.8%). The number of Molluscum contagiosum lesions was significantly reduced with potassium hydroxide 10% and 15%. The main efficacy outcome was achieved in 58.8% of children in the potassium hydroxide 10% group (P = .03 vs placebo) and in 64.3% of children in the potassium hydroxide 15% group (P = .02 vs placebo). Potassium hydroxide 10% and 15% were not significantly different in efficacy from each other. Potassium hydroxide 10% and placebo were better tolerated than potassium hydroxide 15%. No adverse events were reported during the study period. Potassium hydroxide 10% and 15% demonstrated high rates of efficacy in clearing Molluscum contagiosum lesions, with potassium hydroxide 10% being better tolerated. © 2018 Wiley Periodicals, Inc.

COMBINED ALUMINIUM SULFATE/HYDROXIDE PROCESS FOR ...

African Journals Online (AJOL)

sulfate, and used for fluoride removal from water by combining with Nalgonda Technique. ... effects on human health and could result in fluorosis. ... [23], nanoscale aluminium oxide hydroxide (AlOOH) [24] and natural zeolite [25], were among.

Calcium looping process for high purity hydrogen production integrated with capture of carbon dioxide, sulfur and halides

Science.gov (United States)

Ramkumar, Shwetha; Fan, Liang-Shih

2013-07-30

A process for producing hydrogen comprising the steps of: (i) gasifying a fuel into a raw synthesis gas comprising CO, hydrogen, steam, sulfur and halide contaminants in the form of H.sub.2S, COS, and HX, wherein X is a halide; (ii) passing the raw synthesis gas through a water gas shift reactor (WGSR) into which CaO and steam are injected, the CaO reacting with the shifted gas to remove CO.sub.2, sulfur and halides in a solid-phase calcium-containing product comprising CaCO.sub.3, CaS and CaX.sub.2; (iii) separating the solid-phase calcium-containing product from an enriched gaseous hydrogen product; and (iv) regenerating the CaO by calcining the solid-phase calcium-containing product at a condition selected from the group consisting of: in the presence of steam, in the presence of CO.sub.2, in the presence of synthesis gas, in the presence of H.sub.2 and O.sub.2, under partial vacuum, and combinations thereof.

F-radiographic study of uranium distribution in iron hydroxides from crusts of weathering

International Nuclear Information System (INIS)

Zhmodik, S.M.; Mironov, A.G.; Nemirovskaya, N.A.

1980-01-01

Presented are the results of study of uranium concentrations and peculiarities of its distribution in iron hydroxides from crusts of weathering of aluminium silicate and carbonate rocks. The age of one crusts of weathering is Quaternary, of others - Tertiary. The effect of climatic conditions, composition of source rocks, hydrochemical zoning of the crust of weathering on the uranium fixation by iron hydroxides has been studied. Gamma-spectroscopy, luminescence and autoradiography methods have been used. The mechanism of formation of increased uranium concentrations in iron hydroxides is considered. A conclusion is made that increased uranium concentrations in iron hydroxides may appear in the process of weathering both of aluminium-silicate and carbonate-containing rocks as a result of uranium sorption by fine dispersed iron hydrates. The use of iron hydroxides with increased (anomalous) uranium concentrations as a direct search feature without additional investigations can lead to wrong conclusions

Alkali metal and alkali metal hydroxide intercalates of the layered transition metal disulfides

International Nuclear Information System (INIS)

Kanzaki, Y.; Konuma, M.; Matsumoto, O.

1981-01-01

The intercalation reaction of some layered transition metal disulfides with alkali metals, alkali metal hydroxides, and tetraalkylammonium hydroxides were investigated. The alkali metal intercalates were prepared in the respective metal-hexamethylphosphoric triamide solutions in vaccuo, and the hydroxide intercalates in aqueous hydroxide solutions. According to the intercalation reaction, the c-lattice parameter was increased, and the increase indicated the expansion of the interlayer distance. In the case of alkali metal intercalates, the expansion of the interlayer distance increased continuously, corresponding to the atomic radius of the alkali metal. On the other hand, the hydroxide intercalates showed discrete expansion corresponding to the effective ionic radius of the intercalated cation. All intercalates of TaS 2 amd NbS 2 were superconductors. The expansion of the interlayer distance tended to increase the superconducting transition temperature in the intercalates of TaS 2 and vice versa in those of NbS 2 . (orig.)

Reductive dehalogenation by layered iron(II)-iron(III) hydroxides and related iron(II) containing solids

DEFF Research Database (Denmark)

Yin, Weizhao

In the present PhD project, novel synthesis and modifications of layered Fe(II)-Fe(III) hydroxides (green rusts, GRs) were investigated with focus on improved dehalogenation of carbon tetrachloride by using modified green rusts and/or altered reaction conditions. The Ph.D. project has comprised: 1...... sulphate green rust formation by aerial oxidation of FeII or co-precipitation by adding Fe(III) salt to Fe(II). In comparison with traditional green rust synthesis, pure GRs were synthesized in minutes. 2. Enhanced dehalogenation of CT by GR in presence of selected amino acids. In presence of glycine......, chloroform (CF) formation is effectively suppressed: less than 10% of CT is transformed to CF, and more than 90% of dehalogenation products are found to be formic acid and carbon monoxide in presence of 60 mM glycine; while a 80% of CF recovery was obtained without amino acids addition. 3. A “switch...

Layered double hydroxide films on nanoporous anodic aluminum oxide/aluminum wire: a new fiber for rapid analysis of Origanum vulgare essential oils.

Science.gov (United States)

Piryaei, Marzieh

2018-01-01

Zn/Al layered double hydroxide (LDH) films were fabricated in situ with anodic aluminium oxide aluminium as both the substrate and the sole aluminium source by means of urea hydrolysis. Headspace solid phase microextraction using LDH fibre in combination with capillary GC-MS was utilised as a monitoring technique for the collection and detection of the volatile compounds of Origanum vulgare. Experimental parameters, including the sample weight, microwave power, extraction time and humidity effect, were examined and optimised.

Mechanisms of mineral membrane fouling growth modulated by pulsed modes of current during electrodialysis: evidences of water splitting implications in the appearance of the amorphous phases of magnesium hydroxide and calcium carbonate.

Science.gov (United States)

Cifuentes-Araya, Nicolás; Astudillo-Castro, Carolina; Bazinet, Laurent

2014-07-15

Experiments revealed the fouling nature evolutions along different electrodialysis (ED) trials, and how it disappears when current pulsation acts repetitively on the interfaces of ion-exchange membranes (IEMs). Fouling was totally controlled on the diluate side of cation-exchange membrane (CEM) by the repetitive pulsation frequency of the higher on-duty ratios applied. They created steady water splitting proton-barriers that neutralized OH(-) leakage through the membrane, decreasing the interfacial pH, and fouling of the concentrate side. The anion-exchange membrane (AEM) on the diluate side was similarly protected, but it was fouled once water splitting OH(-) generation became either intense enough or excessively weak. Interestingly, amorphous magnesium hydroxide (AMH) stemmed on the CEM-diluate side from brucite under intense water splitting OH(-) generation, and/or strong OH(-) leakage electromigration through the membrane. Water dissociation and overlimiting current regimes triggered drastic water molecule removal from crystal lattices through an accelerated cascade water splitting reaction. Also, amorphous calcium carbonate (ACC) appeared on CEM under intense water splitting reaction, and disappeared once intense OH(-) leakage was allowed by the water splitting proton-barrier dissipation. Our findings have implications for membrane fouling control, as well as for the understanding of the growth behavior of CaCO3 and Mg(OH)2 species on electromembrane interfaces. Copyright © 2014 Elsevier Inc. All rights reserved.

A strategy of precipitated calcium carbonate (CaCO{sub 3}) fillers for enhancing the mechanical properties of polypropylene polymers

Energy Technology Data Exchange (ETDEWEB)

Thenepalli, Thriveni; Ahn, Ji Whan [Korea Institute of Geoscience and Mineral Resources (KIGAM), Daejeon (Korea, Republic of); Ahn, Young Jun; Han, Choon [Kwangwoon University, Seoul (Korea, Republic of); Ramakrishna, Chilakala [Hanil Cement, Danyang (Korea, Republic of)

2015-06-15

A wide variety of fillers are currently used in more than twenty types of polymer resins, although four of them alone (polypropylene, polyamides, thermoplastic polyesters, and polyvinyl chloride) account for 90% of the market of mineral fillers in plastics. Polypropylene (PP) and PVC dominate the market for calcium carbonate. PP is a versatile reinforcement material that can meet engineering and structural specifications and is widely used for automotive components, home appliances, and industrial applications. Talc, mica, clay, kaolin, wollastonite, calcium carbonates, feldspar, aluminum hydroxide, glass fibers, and natural fibers are commonly used in fillers. Among these, calcium carbonate (both natural and synthetic) is the mos abundant and affords the possibility of improved surface finishing, control over the manufacture of products, and increased electric resistance and impact resistance. Meeting the global challenge to reduce the weight of vehicles by using plastics is a significant issue. The current the global plastic and automobile industry cannot survive without fillers, additives, and reinforcements. Polypropylene is a major component of the modern plastic industry, and currently is used in dashboards, wheel covers, and some engine parts in automobiles. This article reports that the use of calcium carbonate fillers with polypropylene is the best choice to enhance the mechanical properties of plastic parts used in automobiles.

Nickel oxide/hydroxide nanoplatelets synthesized by chemical precipitation for electrochemical capacitors

International Nuclear Information System (INIS)

Wu, M.-S.; Hsieh, H.-H.

2008-01-01

Nickel hydroxide powder prepared by directly chemical precipitation method at room temperature has a nanoplatelet-like morphology and could be converted into nickel oxide at annealing temperature higher than 300 deg. C, confirmed by the thermal gravimetric analysis and X-ray diffraction. Annealing temperature influences significantly both the electrical conductivity and the specific surface area of nickel oxide/hydroxide powder, and consequently determines the capacitor behavior. Electrochemical capacitive behavior of the synthesized nickel hydroxide/oxide film is investigated by cyclic voltammetry and electrochemical impedance spectroscope methods. After 300 deg. C annealing, the highest specific capacitance of 108 F g -1 is obtained at scan rate of 10 mV s -1 . When annealing temperature is lower than 300 deg. C, the electrical conductivity of nickel hydroxide dominates primarily the capacitive behavior. When annealing temperature is higher than 300 deg. C, both electrical conductivity and specific surface area of the nickel oxide dominate the capacitive behavior

Pilot-scale demonstration of the OSCAR process for high-temperature multipollutant control of coal combustion flue gas, using carbonated fly ash and mesoporous calcium carbonate

Energy Technology Data Exchange (ETDEWEB)

Gupta, H.; Thomas, T.J.; Park, A.H.A.; Iyer, M.V.; Gupta, P.; Agnihotri, R.; Jadhav, R.A.; Walker, H.W.; Weavers, L.K.; Butalia, T.; Fan, L.S. [Ohio State University, Columbus, OH (United States)

2007-07-15

A pilot-scale study of the Ohio State Carbonation Ash Reactivation (OSCAR) process was performed to demonstrate the reactivity of two novel calcium-based sorbents toward sulfur and trace heavy metal (arsenic, selenium, and mercury) capture in the furnace sorbent injection (FSI) mode on a 0.365 m{sup 3}/s slipstream of a bituminous coal-fired stoker boiler. The sorbents were synthesized by bubbling CO{sub 2} to precipitate calcium carbonate (a) from the unreacted calcium present in the lime spray dryer ash and (b) from calcium hydroxide slurry that contained a negatively charged dispersant. The heterogeneous reaction between these sorbents and SO{sub 2} gas occurred under entrained flow conditions by injecting fine sorbent powders into the flue gas slipstream. The reacted sorbents were captured either in a hot cyclone (about 650{sup o}C) or in the relatively cooler downstream baghouse (about 230{sup o}C). The baghouse samples indicated about 90% toward sulfation and captured arsenic, selenium and mercury to 800 ppmw, 175 ppmw and 3.6 ppmw, respectively.

Cementing Material From Rice Husk-Broken Bricks-Spent Bleaching Earth-Dried Calcium Carbide Residue

Directory of Open Access Journals (Sweden)

Muthengia Jackson Washira

2012-10-01

Full Text Available A cementious material, coded CSBR (Carbide residue Spent bleaching earth Broken bricks and Rice husks, was made from dried calcium carbide residue (DCCR and an incinerated mix of rice husks (RH, broken bricks (BB and spent bleaching earth (SBE. Another material, coded SBR (Spent bleaching earth Broken bricks and Rice husk ash, was made from mixing separately incinerated RH, SBE and ground BB in the same ash ratio as in CSBR. When CSBR was inter-ground with Ordinary Portland Cement (OPC, it showed a continued decrease in Ca(OH2 in the hydrating cement as a function of curing time and replacement levels of the cement. Up to 45 % replacement of the OPC by CSBR produced a Portland pozzolana cement (PPC material that passed the relevant Kenyan Standard. Incorporation of the CSBR in OPC reduces the resultant calcium hydroxide from hydrating Portland cement. The use of the waste materials in production of cementitious material would rid the environment of wastes and lead to production of low cost cementitious material.

Kinetic concepts of thermally stimulated reactions in solids

Science.gov (United States)

Vyazovkin, Sergey

Historical analysis suggests that the basic kinetic concepts of reactions in solids were inherited from homogeneous kinetics. These concepts rest upon the assumption of a single-step reaction that disagrees with the multiple-step nature of solid-state processes. The inadequate concepts inspire such unjustified anticipations of kinetic analysis as evaluating constant activation energy and/or deriving a single-step reaction mechanism for the overall process. A more adequate concept is that of the effective activation energy, which may vary with temperature and extent of conversion. The adequacy of this concept is illustrated by literature data as well as by experimental data on the thermal dehydration of calcium oxalate monohydrate and thermal decomposition of calcium carbonate, ammonium nitrate and 1,3,5,7- tetranitro-1,3,5,7-tetrazocine.

Nickel hydroxide modified electrodes for urea determination

Directory of Open Access Journals (Sweden)

Luiz Henrique Dall´Antonia

2007-03-01

Full Text Available Nickel hydroxide films were prepared by electrodeposition from a solution Ni(NO32 0,05 mol L ?¹ on ITO electrodes (Tin oxide doped with Indium on PET-like plastic film, applying a current of - 0,1 A cm ?² during different time intervals between 1800 and 7200 s. The electrochemical behavior of the nickel hydroxide electrode was investigated through a cyclic voltammogram, in NaOH 1,0 mol L ?¹, where it was observed two peaks in the profile in 0,410 and 0,280 V, corresponding to redox couple Ni(II/Ni(III. A sensor for urea presenting a satisfactory answer can be obtained when, after the deposit of the film of Ni(OH2 on the electrode of nickel, it is immersed in a solution of NaOH 1,0 mol L ?¹ and applying a potential of + 0,435 V, where the maximum of the anodic current occurs in the cyclic voltammogram. Analyzing the results it can be observed that, for a range of analite concentration between 5 to 50 m mol L ?¹, the behavior is linear and the sensibility found was of 20,3 mA cm?² (mol L?¹?¹, presenting reproducibility confirming the nickel hydroxide electrodes utilization for the determination of urea.

Long term mechanical properties of alkali activated slag

Science.gov (United States)

Zhu, J.; Zheng, W. Z.; Xu, Z. Z.; Leng, Y. F.; Qin, C. Z.

2018-01-01

This article reports a study on the microstructural and long-term mechanical properties of the alkali activated slag up to 180 days, and cement paste is studied as the comparison. The mechanical properties including compressive strength, flexural strength, axis tensile strength and splitting tensile strength are analyzed. The results showed that the alkali activated slag had higher compressive and tensile strength, Slag is activated by potassium silicate (K2SiO3) and sodium hydroxide (NaOH) solutions for attaining silicate modulus of 1 using 12 potassium silicate and 5.35% sodium hydroxide. The volume dosage of water is 35% and 42%. The results indicate that alkali activated slag is a kind of rapid hardening and early strength cementitious material with excellent long-term mechanical properties. Single row of holes block compressive strength, single-hole block compressive strength and standard solid brick compressive strength basically meet engineering requirements. The microstructures of alkali activated slag are studied by X-ray diffraction (XRD). The hydration products of alkali-activated slag are assured as hydrated calcium silicate and hydrated calcium aluminate.

Removal of uranium and priority pollutant metals from Fernald Environmental Management Project wastewater utilizing potassium ferrate

International Nuclear Information System (INIS)

Hampshire, Lyle H.; Potts, Michael E.

1992-01-01

A side-by-side treatment comparison between calcium hydroxide and TRU/Clear '4', a potassium ferrate based wastewater treatment chemical, was performed in a process wastewater and stormwater treatment facility. Results from the full-scale plant testing demonstrated that potassium ferrate could achieve the same treatment levels as calcium hydroxide while generating 55% less sludge than the calcium hydroxide treatment. The testing also showed that utilization of potassium ferrate would minimize the volume of sludge generated and assist in the reduction of total waste management costs associated with storage, monitoring, transportation, and final disposition of generated sludge. (author)

The effect of polymers onto the size of zinc layered hydroxide salt and its calcined product

Science.gov (United States)

Hussein, Mohd Zobir bin; Ghotbi, Mohammad Yeganeh; Yahaya, Asmah Hj; Abd Rahman, Mohd Zaki

2009-02-01

Zinc hydroxide nitrate, a brucite-like layered material was synthesized using pH control method. Poly(vinyl alcohol) and poly(ethylene glycol) were used at various percentages as size decreasing agents during the synthesis of zinc hydroxide nitrate. SEM and PXRD showed the decrease of size and thickness of the resultant zinc hydroxide nitrates. TG and surface area data confirmed the decrease of the particle sizes, too. When zinc hydroxide nitrates were heat treated at 500 °C, the physical properties of nano zinc oxides obtained depended on the parent material, zinc hydroxide nitrate.

Analysis of Aloe vera cytotoxicity and genotoxicity associated with endodontic medication and laser photobiomodulation.

Science.gov (United States)

Carvalho, Nayane Chagas; Guedes, Simone Alves Garcez; Albuquerque-Júnior, Ricardo Luiz Cavalcanti; de Albuquerque, Diana Santana; de Souza Araújo, Adriano Antunes; Paranhos, Luiz Renato; Camargo, Samira Esteves Afonso; Ribeiro, Maria Amália Gonzaga

2018-01-01

This study aims to evaluate, in vitro, the effect of Aloe vera associated with endodontic medication, with or without laser photobiomodulation (FTL) irradiation in FP6 human pulp fibroblasts. The materials were divided into eight groups: CTR - control; CL - FTL alone; AA - Aloe vera with distilled water; AL - Aloe vera with distilled water and FTL; HA - calcium hydroxide P.A. with distilled water; HL - calcium hydroxide P.A. with distilled water and FTL; HAA - calcium hydroxide P.A. with Aloe vera and distilled water; HAL - calcium hydroxide P.A. with Aloe vera, distilled water, and FTL. The cytotoxicity was evaluated by MTT assay at 24, 48, and 72h and the genotoxicity by micronucleus test assay. This study was performed in triplicate. Data obtained in both tests were statistically analyzed by ANOVA and Tukey's tests (p≤0.05). Group AA presented high genotoxicity and low cytotoxicity. After 24, 48, and 72h, the group HAA significantly reduced the cell viability. Interaction with FTL showed slightly increase cell viability after 24 and 48h in groups CL and HL (pAloe vera allowed higher cell viability in human pulp fibroblasts in the presence of calcium hydroxide or with FTL separately, but genotoxicity increased in these associations. Copyright © 2017 Elsevier B.V. All rights reserved.

Mammary-Specific Ablation of the Calcium-Sensing Receptor During Lactation Alters Maternal Calcium Metabolism, Milk Calcium Transport, and Neonatal Calcium Accrual

Science.gov (United States)

Mamillapalli, Ramanaiah; VanHouten, Joshua; Dann, Pamela; Bikle, Daniel; Chang, Wenhan; Brown, Edward

2013-01-01

To meet the demands for milk calcium, the lactating mother adjusts systemic calcium and bone metabolism by increasing dietary calcium intake, increasing bone resorption, and reducing renal calcium excretion. As part of this adaptation, the lactating mammary gland secretes PTHrP into the maternal circulation to increase bone turnover and mobilize skeletal calcium stores. Previous data have suggested that, during lactation, the breast relies on the calcium-sensing receptor (CaSR) to coordinate PTHrP secretion and milk calcium transport with calcium availability. To test this idea genetically, we bred BLG-Cre mice with CaSR-floxed mice to ablate the CaSR specifically from mammary epithelial cells only at the onset of lactation (CaSR-cKO mice). Loss of the CaSR in the lactating mammary gland did not disrupt alveolar differentiation or milk production. However, it did increase the secretion of PTHrP into milk and decreased the transport of calcium from the circulation into milk. CaSR-cKO mice did not show accelerated bone resorption, but they did have a decrease in bone formation. Loss of the mammary gland CaSR resulted in hypercalcemia, decreased PTH secretion, and increased renal calcium excretion in lactating mothers. Finally, loss of the mammary gland CaSR resulted in decreased calcium accrual by suckling neonates, likely due to the combination of increased milk PTHrP and decreased milk calcium. These results demonstrate that the mammary gland CaSR coordinates maternal bone and calcium metabolism, calcium transport into milk, and neonatal calcium accrual during lactation. PMID:23782944

X-Ray Diffraction Studies on the Thermal Stability of Calcium ...

African Journals Online (AJOL)

Calcium-Strontium hydroxyapatite (HAP) solid solutions in the presence and absence of diethylamine (DEA) were prepared by the method of co-precipitation from basic media. The samples were heated at 773.15K in a furnace. Characterization of the samples by x-ray powder diffractometry, atomic absorption spectroscopy ...

Removal of ammonia nitrogen from leachate of Muribeca municipal solid waste landfill, Pernambuco, Brazil, using natural zeolite as part of a biochemical system.

Science.gov (United States)

Lins, Cecilia Maria M S; Alves, Maria Cristina M; Campos, Juacyara C; Silva, Fabrícia Maria S; Jucá, José Fernando T; Lins, Eduardo Antonio M

2015-01-01

The inadequate disposal of leachate is one of the key factors in the environmental impact of urban solid waste landfills in Brazil. Among the compounds present in the leachates from Brazilian landfills, ammonia nitrogen is notable for its high concentrations. The purpose of this study was to assess the efficiency of a permeable reactive barrier filled with a natural zeolite, which is part of a biochemical system for the tertiary treatment of the leachate from Muribeca Municipal Solid Waste Landfill in Pernambuco, Brazil, to reduce its ammonia nitrogen concentration. This investigation initially consisted of kinetic studies and batch equilibrium tests on the natural zeolite to construct the sorption isotherms, which showed a high sorption capacity, with an average of 12.4 mg NH4+.L(-1), a value close to the sorption rates found for the aqueous ammonium chloride solution. A permeable reactive barrier consisting of natural zeolite, as simulated by the column test, was efficient in removing the ammonia nitrogen present in the leachate pretreated with calcium hydroxide. Nevertheless, the regenerated zeolite did not satisfactorily maintain the sorption properties of the natural zeolite, and an analysis of their cation-exchange properties showed a reduced capacity of 54 meq per 100 g for the regenerated zeolite compared to 150 meq per 100 g for the natural zeolite.

Effects of calcium impurity on phase relationship, ionic conductivity ...

Indian Academy of Sciences (India)

Home; Journals; Bulletin of Materials Science; Volume 39; Issue 3. Effects of calcium impurity on phase relationship, ionic conductivity and microstructure of Na + - β / b e t a " -alumina solid electrolyte. SUNG-TAE LEE DAE-HAN LEE SANG-MIN LEE SANG-SOO HAN SANG-HYUNG LEE SUNG-KI LIM. Volume 39 Issue 3 ...

Calcium disodium hexathiodiphosphate(IV octahydrate

Directory of Open Access Journals (Sweden)

Claus Ehrhardt

2010-08-01

Full Text Available Single crystals of the title compound, CaNa2(P2S6·8H2O, were obtained by adding calcium hydroxide to an aqueous solution of Na4(P2S6·6H2O. The structure is isotypic with that of its strontium analogue and consists of one Ca2+ cation, two Na+ cations, one-half of a centrosymmetric (P2S64− anion with staggered confirmation and four water molecules in the asymmetric unit. The crystal structure can be described as being built up from layers of cations and anions extending parallel to (101. Within a layer, each CaO8 polyhedron is connected via edge-sharing to two NaO4S2 octahedra and to one NaO2S4 octaedron. The NaO4S2 octahedra are, in turn, linked with two (P2S64− anions through common corners. Various O—H...S hydrogen-bonding interactions lead to cohesion of adjacent layers. The Ca2+ and one Na+ cation are situated on a twofold rotation axis and the second Na+ cation is situated on an inversion centre.

Study of the radium sorption/desorption on goethite

International Nuclear Information System (INIS)

Bassot, S.; Stammose, D.; Mallet, C.; Lefebvre, C.; Ferreux, J.-M.

2000-01-01

The oxi-hydroxides, present at trace level in uranium mill tailings, are responsible of about 70% of the 226 radium sorption, half being fixed on crystallized forms. This radionuclide (half time=1622y), present at high level (50 to 100kBq.kg -1 ), can be released in groundwater, involving a possible contamination of the food chain (actual concentration limit=0.37Bq.1 -1 ). So, it is very important to point out the mechanisms of the radium sorption/desorption on crystallized oxi-hydroxides as a function of chemical conditions of the system. The radium sorption on synthetic goethite α-FeOOH has been studied as a function of contact time, initial radium activity, pH, sodium and calcium concentrations. The results show that, after one hour of contact time (necessary to reach equilibrium), the radium sorption increases widely in a pH range 6-7. The increase of Na + concentration is without influence on the radium sorption, indicating the low interactions between sodium and surface sites. At the opposite, the presence of calcium in solution decreases widely the radium sorption, that indicates a competition between calcium and radium for the same kind of sorption sites of the oxi-hydroxide surface. The percentage of radium desorbed increases widely with time, from 1 to 120h and becomes constant at a time higher than 120h. This long equilibrium time for desorption in comparison with sorption one can be explain by a local evolution of the sorption sites of the solid, which become less accessible for the solution in contact. (author)

Leaching characteristics of calcium-based compounds in MSWI Residues: From the viewpoint of clogging risk

International Nuclear Information System (INIS)

Xia, Yi; Zhang, Hua; Phoungthong, Khamphe; Shi, Dong-Xiao; Shen, Wen-Hui; Shao, Li-Ming; He, Pin-Jing

2015-01-01

Highlights: • The leaching behavior of Ca-based compounds commonly in MSWI residues was studied. • pH is the crucial factor for calcium leaching process. • CaCO 3 was the most sensitive to leaching temperature and Ca 3 (PO 4 ) 2 was the least. • Ca leaching of MSWIBA and SAPCR attributed to CaCO 3 and Ca 3 (PO 4 ) 2 respectively. • Potential clogging ability of MSWI residues leachate in open air was calculated. - Abstract: Leachate collection system (LCS) clogging caused by calcium precipitation would be disadvantageous to landfill stability and operation. Meanwhile, calcium-based compounds are the main constituents in both municipal solid waste incineration bottom ash (MSWIBA) and stabilized air pollution control residues (SAPCR), which would increase the risk of LCS clogging once these calcium-rich residues were disposed in landfills. The leaching behaviors of calcium from the four compounds and municipal solid waste incineration (MSWI) residues were studied, and the influencing factors on leaching were discussed. The results showed that pH was the crucial factor in the calcium leaching process. CaCO 3 and CaSiO 3 began leaching when the leachate pH decreased to less than 7 and 10, respectively, while Ca 3 (PO 4 ) 2 leached at pH < 12. CaSO 4 could hardly dissolve in the experimental conditions. Moreover, the sequence of the leaching rate for the different calcium-based compounds is as follows: CaSiO 3 > Ca 3 (PO 4 ) 2 > CaCO 3 . The calcium leaching from the MSWIBA and SAPCR separately started from pH < 7 and pH < 12, resulting from CaCO 3 and Ca 3 (PO 4 ) 2 leaching respectively, which was proven by the X-ray diffraction results. Based on the leaching characteristics of the different calcium compounds and the mineral phase of calcium in the incineration residues, simulated computation of their clogging potential was conducted, providing the theoretical basis for the risk assessment pertaining to LCS clogging in landfills

Solid adsorbents for removal of hydrogen sulphide from hot gas

Energy Technology Data Exchange (ETDEWEB)

Furimsky, E.; Yumura, Motoo

1986-04-01

A wide range of solids have been tested as potential adsorbents for H/sub 2/S removal from hot gas. These solids can be divided into two main groups, i.e., the adsorbents containing alkaline earth metals and those containing transition metals. Among the former, calcium oxide and naturally occurring materials such as limestone, dolomite and calcium silicate have attracted a great deal of attention. The adsorbents of the second group include iron oxide alone or in combination with some supports, zinc oxide, zinc ferrite and manganese oxide. The materials containing both the alkaline earth metals and transition metals, e.g., manganese nodules, fly ash and the reject from the aluminium industry (red mud) have been evaluated as well.

Hydrothermal synthesis and formation mechanism of hexagonal yttrium hydroxide fluoride nanobundles

International Nuclear Information System (INIS)

Tian, Li; Sun, QiLiang; Zhao, RuiNi; He, HuiLin; Xue, JianRong; Lin, Jun

2013-01-01

Graphical abstract: The formation of yttrium hydroxide fluorides nanobundles can be expressed as a precipitation transformation from cubic NaYF 4 to hexagonal NaYF 4 and to hexagonal Y(OH) 2.02 F 0.98 owing to ion exchange. - Highlights: • Novel Y(OH) 2.02 F 0.98 nanobundles have been successfully prepared by hydrothermal method. • The branched nanobundles composed of numerous oriented-attached nanoparticles has been studied. • The growth mechanism is proposed to be ion exchange and precipitation transformation. - Abstract: This article presents the fabrication of hexagonal yttrium hydroxide fluoride nanobundles via one-pot hydrothermal process, using yttrium nitrate, sodium hydroxide and ammonia fluoride as raw materials to react in propanetriol solvent. The X-ray diffraction pattern clearly reveals that the grown product is pure yttrium hydroxide fluoride, namely Y(OH) 2.02 F 0.98 . The morphology and microstructure of the synthesized product is testified to be nanobundles composed of numerous oriented-attached nanoparticles as observed from the field emission scanning electron microscopy (FESEM). The chemical composition was analyzed by the energy dispersive spectrum (EDS), confirming the phase transformation of the products which was clearly consistent with the result of XRD analysis. It is proposed that the growth of yttrium hydroxide fluoride nanobundles be attributed to ion exchange and precipitation transformation

Synthesis of calcium phosphates and porous hydroxyapatite beads prepared by emulsion method

Energy Technology Data Exchange (ETDEWEB)

Chen, B.-H. [Faculty of Biotechnology, Kaohsiung Medical University, 100 Shih-Chuan 1st Road, Kaohsiung 807, Taiwan (China); Chen, K.-I [Department of Electronics Engineering and Computer Science, Tung-Fang Institute of Technology, 100 Dungfang Road, Hunei, Kaohsiung, Taiwan (China); Ho, M.-L. [Department of Physiology, Kaohsiung Medical University, Kaohsiung 807, Taiwan (China); Chen, H.-N. [Faculty of Medicinal and Applied Chemistry, Kaohsiung Medical University, 100 Shih-Chuan 1st Road, Kaohsiung 807, Taiwan (China); Chen, W.-C. [Faculty of Dentistry, Kaohsiung Medical University, Kaohsiung 807, Taiwan (China); Wang, C.-K. [Faculty of Medicinal and Applied Chemistry, Kaohsiung Medical University, 100 Shih-Chuan 1st Road, Kaohsiung 807, Taiwan (China)], E-mail: ckwang@kmu.edu.tw

2009-01-15

Raw calcium phosphates were synthesized via a chemical reaction between 0.5 M orthophosphoric acid and 0.5 M calcium hydroxide. Hydroxyapatite (HAp), {beta}-tricalcium phosphate ({beta}-TCP) or biphase calcium phosphate (BCP) comprising HAp and {beta}-TCP were obtained by changing pH value, Ca/P ratio, and the addition of glycerol. The as-synthesized and heat-treated powders were analyzed by X-ray diffraction (XRD) and Fourier transformation infrared spectrometry (FTIR). Thermal stability of the pure apatite phase was obtained to be 1300 deg. C, while synthesis was done at the pH value of 10.0 with a Ca/P ratio of 2.0 and a temperature of 37 deg. C. Besides, the {beta}-TCP phase (with higher purity) was achieved at 800 deg. C, whose synthesis was done at pH 6.4 with a Ca/P ratio of 1.5 and a temperature of 37 deg. C. Therefore, the biphase bioceramics comprising of HAp and {beta}-TCP could be obtained, since it was manipulated suitably. The HAp raw material was subjected to a simple emulsion method for the preparation of porous beads. They should have the advantage of exhibiting higher adsorptive ability and osteoconductivity in comparison with the sintered dense apatite. Additionally, the porous beads of apatite were demonstrated to be non-toxic to cells, and should be suitable for the use as a scaffold of cultured bone and bone graft material, as well as for drug delivery systems.

Solid state synthesis and structural refinement of polycrystalline ...

Indian Academy of Sciences (India)

Unknown

This makes them a potential material for nuclear waste management in synthetic ... solid solution of lanthanum substituted calcium titanate. The SEM and EDAX .... symmetry operations to complete the coverage (figure 3). The plots are square ...

Reduction of orthophosphates loss in agricultural soil by nano calcium sulfate.

Science.gov (United States)

Chen, Dong; Szostak, Paul; Wei, Zongsu; Xiao, Ruiyang

2016-01-01

Nutrient loss from soil, especially phosphorous (P) from farmlands to natural water bodies via surface runoff or infiltration, have caused significant eutrophication problems. This is because dissolved orthophosphates are usually the limiting nutrient for algal blooms. Currently, available techniques to control eutrophication are surprisingly scarce. Calcium sulfate or gypsum is a common soil amendment and has a strong complexation to orthophosphates. The results showed that calcium sulfate reduced the amount of water extractable P (WEP) through soil incubation tests, suggesting less P loss from farmlands. A greater decrease in WEP occurred with a greater dosage of calcium sulfate. Compared to conventional coarse calcium sulfate, nano calcium sulfate further reduced WEP by providing a much greater specific surface area, higher solubility, better contact with the fertilizer and the soil particles, and superior dispersibility. The enhancement of the nano calcium sulfate for WEP reduction is more apparent for a pellet- than a powdered- fertilizer. At the dosage of Ca/P weight ratio of 2.8, the WEP decreased by 31±5% with the nano calcium sulfate compared to 20±5% decrease with the coarse calcium sulfate when the pellet fertilizer was used. Computation of the chemical equilibrium speciation shows that calcium hydroxyapatite has the lowest solubility. However, other mineral phases such as hydroxydicalcium phosphate, dicalcium phosphate dihydrate, octacalcium phosphate, and tricalcium phosphate might form preceding to calcium hydroxyapatite. Since calcium sulfate is the major product of the flue gas desulfurization (FGD) process, this study demonstrates a potential beneficial reuse and reduction of the solid FGD waste. Copyright © 2015 Elsevier B.V. All rights reserved.

High-temperature CO2 capture cycles of hydrated limestone prepared with aluminum (hydr)oxides derived from kaolin

International Nuclear Information System (INIS)

Wang, Ke; Zhao, Pengfei; Guo, Xin; Han, Dongtai; Chao, Yang

2014-01-01

Highlights: • Hydrated limestone exhibited a higher reactivity and stability. • Microstructure of hydrated limestone was significantly improved. • Hydrated limestone still suffered less loss-incapacity. • Hydrated limestone sorbents with kaolin-based binders were prepared and characterized. • Sorbents prepared from hydrated limestone and Al(OH) 3 binder are a promising sorbent. - Abstract: A simple and convenient process was used to improve the utilization of natural limestone and kaolin for calcium looping technology and environmental applications. The calcined natural limestone modified with the distilled water (denoted as Limestone-W), was systematically studied and compared with the other CaO sorbents (calcium acetate, calcium D-gluconate and calcined natural limestone). These CaO-based sorbents were tested for their CO 2 capture behavior through 20 carbonation/calcination cycles in a thermo-gravimetric analyzer (TGA). Their morphology, pore structure and phase composition before and after carbonation/calcination cycles were determined by scanning electron microscopy, nitrogen adsorption, and X-ray diffraction. The first-cycle and multicycle sorption results revealed that the Limestone-W sorbent exhibited a relatively faster reaction rate and higher cyclic CO 2 capture. The characterization data indicated that the Limestone-W was composed of a special calcium oxide structure with lower crystalline and higher porosity nanoparticles, which appeared to be the main reasons for its higher CO 2 capture capability. However, the Limestone-W still suffered loss of reactivity, even though it was less pronounced than the other CaO sorbent. To avoid this unfavorable effect, a thermally stable inert material (aluminum hydroxide derived from kaolin) was incorporated into the Limestone-W structure. This new sorbent revealed higher stability because the formation of a stable framework of Ca 12 Al 14 O 33 particles hindered densification and sintering of the CaO phase

Lubrication performance and mechanisms of Mg/Al-, Zn/Al-, and Zn/Mg/Al-layered double hydroxide nanoparticles as lubricant additives

International Nuclear Information System (INIS)

Li, Shuo; Bhushan, Bharat

2016-01-01

Highlights: • Mg/Al-, Zn/Al- and Zn/Mg/Al-layered double hydroxide were synthesized. • Mg/Al-LDH had superior tribological performance compared to other LDHs. • The best thermal stability of Mg/Al-LDH was responsible for its friction property. - Abstract: Solid lubricant particles are commonly used as oil additives for low friction and wear. Mg/Al-, Zn/Al-, and Zn/Mg/Al-layered double hydroxides (LDH) were synthesized by coprecipitation method. The benefits of LDH nanoparticles are that they can be synthesized using chemical methods where size and shape can be controlled, and can be modified organically to allow dispersal in fluids. The LDH nanoparticles were characterized by X-ray diffraction, scanning electron microscope, thermogravimetry, and differential scanning calorimetry. A pin-on-disk friction and wear tester was used for evaluating the friction and wear properties of LDH nanoparticles as lubricant additives. LDH nanoparticles have friction-reducing and anti-wear properties compared to oil without LDHs. Mg/Al-LDH has the best lubrication, possibly due to better thermal stability in severe conditions.

Lubrication performance and mechanisms of Mg/Al-, Zn/Al-, and Zn/Mg/Al-layered double hydroxide nanoparticles as lubricant additives

Energy Technology Data Exchange (ETDEWEB)

Li, Shuo [School of Materials Science and Technology, China University of Geosciences (Beijing), 29 Xueyuan Road, Haidian Distract, Beijing 100083 (China); Nanoprobe Laboratory for Bio- & Nanotechnology and Biomimetics (NLBB), The Ohio State University, 201 W. 19th Avenue Columbus, OH 43210-1142 (United States); Bhushan, Bharat, E-mail: bhushan.2@osu.edu [Nanoprobe Laboratory for Bio- & Nanotechnology and Biomimetics (NLBB), The Ohio State University, 201 W. 19th Avenue Columbus, OH 43210-1142 (United States)

2016-08-15

Highlights: • Mg/Al-, Zn/Al- and Zn/Mg/Al-layered double hydroxide were synthesized. • Mg/Al-LDH had superior tribological performance compared to other LDHs. • The best thermal stability of Mg/Al-LDH was responsible for its friction property. - Abstract: Solid lubricant particles are commonly used as oil additives for low friction and wear. Mg/Al-, Zn/Al-, and Zn/Mg/Al-layered double hydroxides (LDH) were synthesized by coprecipitation method. The benefits of LDH nanoparticles are that they can be synthesized using chemical methods where size and shape can be controlled, and can be modified organically to allow dispersal in fluids. The LDH nanoparticles were characterized by X-ray diffraction, scanning electron microscope, thermogravimetry, and differential scanning calorimetry. A pin-on-disk friction and wear tester was used for evaluating the friction and wear properties of LDH nanoparticles as lubricant additives. LDH nanoparticles have friction-reducing and anti-wear properties compared to oil without LDHs. Mg/Al-LDH has the best lubrication, possibly due to better thermal stability in severe conditions.

Precipitation of the rare earth double sodium and rare earths from the sulfuric liquor and the conversion into rare earth hydroxides through meta ethic reaction

International Nuclear Information System (INIS)

Abreu, Renata D.; Oliveira, Ester F.; Brito, Walter de; Morais, Carlos A.

2007-01-01

This work presents the purification study of the rare earths through precipitation of rare earth and sodium (Na TR (SO 4 ) 2 . x H 2 O)) double sulfate and his conversion to rare earths hydroxide TR(OH) 3 by meta ethic reaction through the addition of sodium hydroxide solution to the solid double sulfate. The study used the sulfuric liquor as rare earth sample, generated in the chemical processing of the monazite with sulfuric acid by the Industrias Nucleares do Brasil - INB, Brazil, after the thorium and uranium extraction. The work investigated the influence of the main variables involved in the precipitation of Na TR(SO 4 ) 2 .xH 2 O and in the conversion for the TR(OH) 3 , as follows: type and excess of the precipitation agent, temperature and time reaction. The obtained solid composites were characterized by X-ray diffraction, infrared and chemical analysis. The double sulfate diffractogram indicated the Na TR(SO 4 ) 2 mono-hydrated. The characterization of the metatese products has shown that, for obtaining the complete conversion of NaTR(SO 4 ) 2 .H 2 O into TR(OH) 3 , the reaction must be hot processed (∼70 deg C) and with small excess of Na OH (≤ 5 percent). (author)

On Calcium Carbonates: from Fundamental Research to Application

OpenAIRE

Brečević, Ljerka; Kralj, Damir

2007-01-01

Appearance of a solid phase from aqueous solution, known as precipitation, is responsible for the formation of numerous natural materials and technological products. Therefore, the knowledge on mechanisms of elementary processes involved in precipitation should be considered in the areas such as geology, oceanology, biomineralization, medicine, basic chemical and pharmaceutical industries, analytical and materials chemistry in particular. Calcium carbonates are a very suitable model system fo...

Magnetic susceptibilities of Ca/sub y/U/sub 1-y/O/sub 2+x/ solid solutions

International Nuclear Information System (INIS)

Hinatsu, Y.; Fujino, T.

1988-01-01

Magnetic susceptibilities of Ca/sub y/U/sub 1-y/O/sub 2+x/ solid solutions with fluorite structure were measured from 4.2 K to room temperature. An antiferromagnetic transition was observed for all the solid solutions examined in this study (y ≤ 0.33). The Neel temperature of the oxygen-hypostoichiometric solid solutions (x 2 solid solutions, but different from that of (U,Th)O 2 solid solutions. The effective magnetic moment decreased with increasing calcium concentration, which indicates the oxidation of uranium in the solid solutions. From the analysis of the magnetic susceptibility data, it was found that the oxidation state of uranium was either tetravalent or pentavalent. The Neel temperature of the hyperstoichiometric solid solutions (x > 0) did not change appreciably with calcium concentrations. From the comparison of the magnetic susceptibility data of the hypostoichiometric solid solutions with those of the hyperstoichiometric solid solutions, the effect of oxygen vacancies is more significant than that of interstitial oxygens on the decrease of magnetic interactions between uranium ions