WorldWideScience

Sample records for skimmers

  1. New oil skimmer from shell

    Energy Technology Data Exchange (ETDEWEB)

    1978-06-01

    Under a program initiated by the US Coast Guard (USCG), Shell Development Co. has developed the Zero-Relative Velocity Skimmer (ZRVS) (Abstract No. 24-30285) which can recover spilled oil in currents up to eight knots. Tests of a full-scale mockup of the system gave excellent results up to the test limit of eight knots and in waves up to 2 ft high. Conventional oil skimmers slow down the floating oil relative to the water so that it can be contained and collected. But when the relative velocity of water and skimmer exceeds 1 to 2 knots, turbulence caused by the skimmer's surface piercing equipment leads to oil escaping. The ZRVS combats this by laying twin floating, adsorbent belts on the surface so they move at the same speed as the water and oil relative to the skimmer. With no relative velocity between them, turbulence is removed, allowing the skimmer to operate effectively in fast currents. The skimmer is a 41 ft catamaran, built in three sections so it can be transported in two aircraft and assembled at the port nearest the spill. The first prototype is due to be completed at the USCG shipyard in the summer of 1978.

  2. The Chalk River helium jet and skimmer system

    International Nuclear Information System (INIS)

    Schmeing, H.; Koslowsky, V.; Wightman, M.; Hardy, J.C.; MacDonald, J.A.; Faestermann, T.; Andrews, H.R.; Geiger, J.S.; Graham, R.L.

    1976-01-01

    A helium jet and skimmer system intended as an interface between a target location at the Chalk River tandem accelerator and the ion source of an on-line separator presently under construction has been developed. The system consists of a target chamber, a 125 cm long capillary, and a one stage skimmer chamber. The designs of the target and skimmer chambers allow one to vary a large number of independent flow and geometrical parameters with accurate reproducibility. Experiments with the β-delayed proton emitter 25 Si (tsub(1/2)=218 ms) produced in the reaction 24 Mg( 3 He,2n) 25 Si show that under optimized conditions about 75% of the reaction products leaving the target are transported to the skimmer. Of those, more than 90% pass through the skimmer orifice, which separates off 97.5% of the transport gas, helium. By introducing an additional helium flow across the skimming orifice the amount of helium separated off the transport jet can be increased to beyond 99.85%, leaving the high throughput of recoils unaffected. (Auth.)

  3. Giant jem wing skimmer and separator for oil and other floating materials, liquids

    International Nuclear Information System (INIS)

    Meier, D.G.

    1991-01-01

    A skimmer and separation process are provided for cleaning oil spills, in which both water and oil can be handled in large amounts. One version of the skimmer is designed for attachment to a ship and includes a floating winglike body for skimming oil comprising flotation tanks, a water passage for minimizing buildup of water in front of the skimmer, vacuum chambers and screens for receiving overflowing oil and water, vacuum pipes for oil and water transfer to a distribution tank, a deflector shield to keep oil and water in front of the skimmer, automatic control valves for flooding, emptying, and depth-setting of the skimmer, an operating platform and control center for observation and operation of the skimmer, a curved oilguiding plate to direct oil to the front of the skimmer, and a swivel attachment for providing free movement of the skimmer when attaching it to the ship's hull. A variant of this skimmer, without the oil-guiding plate and water passage, is provided for stationary operation in the case where oil must be skimmed from a water surface adjacent to a stationary leaking oil source. An associated overflow and separation system consists of pumps, transfer pipes, flotation vessels, separation equipment, and collector tanks. 13 figs

  4. Tank testing of skimmers with waxy and viscous oils

    International Nuclear Information System (INIS)

    1989-10-01

    A series of tests of four offshore skimmers (Framo ACW-400, GT-185, Walosep W2, Heavy Oil Skimmer) was conducted in a 120-by-60-meter wave basin. Each skimmer was tested with each of 3 oils: a conventional crude, a waxy crude, and a bunker oil. Each test involved 4-6 h of skimming, partly conducted in waves having a period of 4 s and heights of 0.4-0.8 m. Near the end of selected tests, the additive Elastol was applied to the oil and its effect on recovery parameters evaluated. All the optimum results were obtained in calm conditions. In general, waves had no effect on the performance of the Walosep W2, had little effect on the performance of the GT-185, and greatly reduced the performance of the Framo. The experimental Heavy Oil Skimmer failed to recover oil at significant rates without addition of Elastol to the oils. The fluid recovery rate less the water entrainment rate generally declined as oil viscosity increased. For a waxy oil, recovery rates under conditions typical of the Grand Banks in summer would be 30-40% less than for a conventional crude with the Framo skimmer and about the same as the recovery rates for conventional crude with the Walosep and GT-185 skimmers. The Walosep, unlike the other skimmers, did not entrain more water when skimming waxy oil compared to conventional oil. Adding Elastol to the oils improved the corrected recovery rates of the Walosep by ca 15% and had no effect on its water entrainment rate. For the Framo, Elastol addition had no effect on the recovery rate but increased its water entrainment rate. Elastol reduced the GT-185's recovery rate by 25-35% and increased its water entrainment rate. Adding Elastol had several negative effects on subsequent downstream operations. 11 refs., 55 figs., 14 tabs

  5. Oil Skimmer apparatus

    International Nuclear Information System (INIS)

    Halter, H.

    1992-01-01

    This patent describes a skimmer craft for collecting and separating liquid pollutants spilled on a body of water. It comprises: a separation tank in the bow of the craft, an intake port to the separation tank disposed at the upper forward end of the separation tank, a sea sled comprising an upper planning surface and a lower buoyant member, and bellows mounted on the bow of the craft, the sea sled, bellows and intake port forming a passageway from the body of water into the separation tanks

  6. KE basin recirculation/skimmer/IX systems restart acceptance test report

    International Nuclear Information System (INIS)

    Derosa, D.C.

    1996-01-01

    The 105 KE Basin Recirculation System and Skimmer Loop have been upgraded to provide the flexibility to run the Ion Exchange Modules on either system to support spent fuel removal for the Spent Nuclear Fuel Project. This Acceptance Test Report Provides the documentation of the leak Testing for the construction work associated with the IXM inlet and outlet piping, places the cartridge filters back in service and provides the functional testing of the IXM's on the recirculation and skimmer systems

  7. Atom Skimmers and Atom Lasers Utilizing Them

    Science.gov (United States)

    Hulet, Randall; Tollett, Jeff; Franke, Kurt; Moss, Steve; Sackett, Charles; Gerton, Jordan; Ghaffari, Bita; McAlexander, W.; Strecker, K.; Homan, D.

    2005-01-01

    Atom skimmers are devices that act as low-pass velocity filters for atoms in thermal atomic beams. An atom skimmer operating in conjunction with a suitable thermal atomic-beam source (e.g., an oven in which cesium is heated) can serve as a source of slow atoms for a magneto-optical trap or other apparatus in an atomic-physics experiment. Phenomena that are studied in such apparatuses include Bose-Einstein condensation of atomic gases, spectra of trapped atoms, and collisions of slowly moving atoms. An atom skimmer includes a curved, low-thermal-conduction tube that leads from the outlet of a thermal atomic-beam source to the inlet of a magneto-optical trap or other device in which the selected low-velocity atoms are to be used. Permanent rare-earth magnets are placed around the tube in a yoke of high-magnetic-permeability material to establish a quadrupole or octupole magnetic field leading from the source to the trap. The atoms are attracted to the locus of minimum magnetic-field intensity in the middle of the tube, and the gradient of the magnetic field provides centripetal force that guides the atoms around the curve along the axis of the tube. The threshold velocity for guiding is dictated by the gradient of the magnetic field and the radius of curvature of the tube. Atoms moving at lesser velocities are successfully guided; faster atoms strike the tube wall and are lost from the beam.

  8. Applications for skimmer coupling systems, combining simultaneous thermal analysers with mass spectrometers

    International Nuclear Information System (INIS)

    Kaisersberger, E.; Post, E.

    1998-01-01

    The sensitivity of the Skimmer coupling for combining the simultaneous thermal analysis (STA) method TG-DTA/DSC and mass spectrometry (MS) is further improved by a factor of three using an automatic vacuum control device. Especially high mass numbers are detected without the common condensation problems met in capillary couplings, as is shown by application of the skimmer coupling for coal, CuGaSe 2 -semiconductor material and polystyrene. The basic idea of the novel pulse thermal analysis technique (PTA) is demonstrated. (Copyright (c) 1998 Elsevier Science B.V., Amsterdam. All rights reserved.)

  9. Oil spill encounter rate: A means of estimating advancing skimmer performance

    International Nuclear Information System (INIS)

    Schulze, R.

    1993-01-01

    A high rate of oil spill recovery can only be achieved if the spilled oil can be collected fast enough for the skimming and pumping systems to operate at their rated capacity. For advancing skimmers, recovery capacity depends on the rate at which the skimming system encounters the oil slick. For these systems, encounter rate depends on skimming speed, sweep width, and the amount of oil available, in this case measured in terms of slick thickness. The computation of the spill encounter rate is described, and a chart is provided that permits the user to determine encounter rate for candidate skimming systems by inspection. Furthermore, a contingency planning worksheet for advancing skimmers is provided that allows the user to evaluate a particular response system. The resulting data can be used to determine the oil slick area that can be covered in a period of time, the volume of oil that can be expected to be recovered in that time based on oil spill planning scenarios, the pumping capacity required for skimming and transfer systems, and the storage requirements for recovered oil. Finally, suggestions are presented on how computations of oil spill encounter rate can be used to make important decisions in procuring advancing skimmers for specific applications. 1 fig., 1 tab

  10. Horizontal, floating, plastic hose oil skimmer

    Energy Technology Data Exchange (ETDEWEB)

    1978-04-01

    A horizontal, floating, plastic hose oil skimmer operates at -20/sup 0/ to +100/sup 0/C as a moving belt driven by a motor at 0.7 kw at 1400 rpm to pick up oil by adhesion from a surface such as that of used cooling water or cutting oil for subsequent stripping and collection by gravity flow. Two models provide collection rates of 10-45 l./hr for diesel oil, 35-115 l./hr for hydraulic oil, and 170-455 l./hr for gear oils and heavy heating oils.

  11. Use of a nesting platform by Gull-billed Terns and Black Skimmers at the Salton Sea, California

    Science.gov (United States)

    Molina, Kathy C.; Ricca, Mark A.; Miles, A. Keith; Schoneman, Christian

    2009-01-01

    In 2006, we constructed an elevated nesting platform at the Salton Sea, California, and monitored its use by Gull-billed Terns and Black Skimmers over three subsequent breeding seasons. Black Skimmers were the first to colonize the platform with a total of five nests in 2006. In 2007 Gull-billed Terns colonized the platform with a total of 28 nests and the number of Black Skimmer nests increased to 20. Neither species nested on the platform in 2008. Low success for both species was probably influenced by at least two factors. First, when both species nested on the platform, nest densities were higher than is typical of their colonies on larger, earthen islands, and colony success may have been reduced by overcrowding. Second, lack of access to water may have reduced chicks' ability to thermoregulate effectively in the hot environment of the Salton Sea. Refinements to the size, design, and location of artificial nesting habitats are necessary to enhance productivity of colonial groundnesting birds at the Salton Sea successfully.

  12. Effect of Skimmer Cone Material on the Spectra of Inductively Coupled Plasma Mass Spectrometry

    International Nuclear Information System (INIS)

    Amr, M.A.; Zahran, N.F.; Helal, A.I.

    2002-01-01

    The inductively coupled plasma ion source for mass spectrometry is very sensitive for multielement analysis with detection limits down to sub part per trillion (ppt). Polyatomic ions which could be formed in the mass spectra may interfere in the analysis of some element. Experimental conditions have great influences on the formation of polyatomic ions. The present work demonstrates that the skimmer materials (Au, Ag, Ni, and Cu) are participating in the formation of polyatomic ions, meanwhile the sampler materials have no real effect. The mechanism of formation of polyatomic ions is explained. Heats of formation of polyatomic species formed from the skimmer materials such as: Au X, Ag X, Ni X and Cu X; where X= Ar, O, N, C and H are calculated by Gaussian program (G 94 W)

  13. Daily survival rates for nests of Black Skimmers from a core breeding area of the Southeastern USA

    Science.gov (United States)

    Brooks, Gillian L.; Sanders, Felicia J.; Gerard, Patrick D.; Jodice, Patrick G.R.

    2014-01-01

    Little is known about the reproductive success of Black Skimmers (Rynchops niger) throughout the southeastern USA where availability of undisturbed beaches for nesting is limited. Daily survival rates (DSR) of nests were examined at three nesting sites in Cape Romain National Wildlife Refuge (CRNWR), South Carolina, USA, 2009–2010. The percent of successful nests (n  =  346 nests) ranged from 42–69% among colony sites when data were pooled across both years. The DSR of nests was primarily related to colony site, predation risk, height of high tide, and clutch size. Predation and overwash were the principal causes of identifiable nest loss, each accounting for ∼33% of nest failures during the two study years. Because of the challenges of resighting skimmer chicks, we were not able to measure chick survival effectively and therefore accurate measures of productivity remain elusive. High variability in nest success among sites within close proximity to each other (stressors such as tropical storms or food availability. Although time-intensive techniques to control predators do exist, management options to limit flooding and overwash are far more limited. Conservation of Black Skimmers in the southeastern USA would benefit from coordinated, multi-state efforts to measure nest and chick survival.

  14. Further development of a mobile oil skimmer catamaran. Weiterentwicklung eines mobilen Oelabschoepfkataramans

    Energy Technology Data Exchange (ETDEWEB)

    Binek, H

    1984-04-01

    Experiments with gushing ramps with different contours have been carried out on a wooden model (No. 1191) of an oil skimmer catamaran. The experiments were carried out on an oil-covered water surface. Further studies, e.g. stability studies, pitching experiments in air and water, determination of water flow rates in the water outlet, and observations of the oil flow inside the catamaran, will be carried out on a plastic model with bulkheads, web frames, plexiglass windows, and side ports. The optimum position of the transversal pipe preventing eddy formation has been determined in systematic experiments. Finally, manoeuvring and circular navigation were investigated. (GB).

  15. The subspecific characters and distribution of the New World Skimmers - Rynchops nigra The subspecific characters and distribution of the New World Skimmers - Rynchops nigra

    Directory of Open Access Journals (Sweden)

    Wetmore Alexander

    1944-09-01

    Full Text Available The distribution of the forms of the New World rayador, or skimmer, Rynchops nigra, and the characters that mark the geographic races, have been matters of interest to me for a number of years, an interest heightened by recent discussions in current literature of the identity of the birds found on the Pacific coast of Mexico, and far to the south in Chile. Investigation into these matters with the material available in the National Museum not being conclusive, specimens from Mexico and the West Indies southward to Argentina and Chile in other large collections in the United states have been assembled through the courtesy of Dr. Robert Cushman Murphy of the American Museum of Natural History, James l.. Peters of the Museum of Comparative Zoology,W. E. C. Todd of the Carnegie Museum, and Dr. Karl P. Schmidt of the Field Museum of Natural History. I have also to thank Dr. Alden H. Miller for the use of one specimen from Chubut in the Museum of Vertebrate Zoology, and Dean Amadon for certain notes on this group of birds that he had assembled.The distribution of the forms of the New World rayador, or skimmer, Rynchops nigra, and the characters that mark the geographic races, have been matters of interest to me for a number of years, an interest heightened by recent discussions in current literature of the identity of the birds found on the Pacific coast of Mexico, and far to the south in Chile. Investigation into these matters with the material available in the National Museum not being conclusive, specimens from Mexico and the West Indies southward to Argentina and Chile in other large collections in the United states have been assembled through the courtesy of Dr. Robert Cushman Murphy of the American Museum of Natural History, James l.. Peters of the Museum of Comparative Zoology,W. E. C. Todd of the Carnegie Museum, and Dr. Karl P. Schmidt of the Field Museum of Natural History. I have also to thank Dr. Alden H. Miller for the use of one specimen

  16. Birds of Two Oceans? Trans-Andean and Divergent Migration of Black Skimmers (Rynchops niger cinerascens) from the Peruvian Amazon.

    Science.gov (United States)

    Davenport, Lisa C; Goodenough, Katharine S; Haugaasen, Torbjørn

    2016-01-01

    Seasonal flooding compels some birds that breed in aquatic habitats in Amazonia to undertake annual migrations, yet we know little about how the complex landscape of the Amazon region is used seasonally by these species. The possibility of trans-Andes migration for Amazonian breeding birds has largely been discounted given the high geographic barrier posed by the Andean Cordillera and the desert habitat along much of the Pacific Coast. Here we demonstrate a trans-Andes route for Black Skimmers (Rynchops niger cinerascens) breeding on the Manu River (in the lowlands of Manu National Park, Perú), as well as divergent movement patterns both regionally and across the continent. Of eight skimmers tracked with satellite telemetry, three provided data on their outbound migrations, with two crossing the high Peruvian Andes to the Pacific. A third traveled over 1800 km to the southeast before transmissions ended in eastern Paraguay. One of the two trans-Andean migrants demonstrated a full round-trip migration back to its tagging location after traveling down the Pacific Coast from latitude 9° South to latitude 37° S, spending the austral summer in the Gulf of Arauco, Chile. This is the first documentation of a trans-Andes migration observed for any bird breeding in lowland Amazonia. To our knowledge, this research also documents the first example of a tropical-breeding waterbird migrating out of the tropics to spend the non-breeding season in the temperate summer, this being the reverse pattern with respect to seasonality for austral migrants in general.

  17. Structure characterization of lipocyclopeptide antibiotics, aspartocins A, B & C, by ESI-MSMS and ESI-nozzle-skimmer-MSMS.

    Science.gov (United States)

    Siegel, Marshall M; Kong, Fangming; Feng, Xidong; Carter, Guy T

    2009-12-01

    Three lipocyclopeptide antibiotics, aspartocins A (1), B (2), and C (3), were obtained from the aspartocin complex by HPLC separation methodology. Their structures were elucidated using previously published chemical degradation results coupled with spectroscopic studies including ESI-MS, ESI-Nozzle Skimmer-MSMS and NMR. All three aspartocin compounds share the same cyclic decapeptide core of cyclo [Dab2 (Asp1-FA)-Pip3-MeAsp4-Asp5-Gly6-Asp7-Gly8-Dab9-Val10-Pro11]. They differ only in the fatty acid side chain moiety (FA) corresponding to (Z)-13-methyltetradec-3-ene-carbonyl, (+,Z)-12-methyltetradec-3-ene-carbonyl and (Z)-12-methyltridec-3-ene-carbonyl for aspartocins A (1), B (2), and C (3), respectively. All of the sequence ions were observed by ESI-MSMS of the doubly charged parent ions. However, a number of the sequence ions observed were of low abundance. To fully sequence the lipocyclopeptide antibiotic structures, these low abundance sequence ions together with complementary sequence ions were confirmed by ESI-Nozzle-Skimmer-MSMS of the singly charged linear peptide parent fragment ions H-Asp5-Gly6-Asp7-Gly8-Dab9-Val10-Pro11-Dab2(1+)-Asp1-FA. Cyclization of the aspartocins was demonstrated to occur via the beta-amino group of Dab2 from ions of moderate intensity in the ESI-MSMS spectra. As the fatty acid moieties do not undergo internal fragmentations under the experimental ESI mass spectral conditions used, the 14 Da mass difference between the fatty acid moieties of aspartocins A (1) and B (2) versus aspartocin C (3) was used as an internal mass tag to differentiate fragment ions containing fatty acid moieties and those not containing the fatty acid moieties. The most numerous and abundant fragment ions observed in the tandem mass spectra are due to the cleavage of the tertiary nitrogen amide of the pipecolic acid residue-3 (16 fragment ions) and the proline residue-11 (7 fragment ions). In addition, the neutral loss of ethanimine from alpha

  18. Fundamental studies of the plasma extraction and ion beam formation processes in inductively coupled plasma mass spectrometry

    International Nuclear Information System (INIS)

    Niu, Hongsen.

    1995-01-01

    The fundamental and practical aspects are described for extracting ions from atmospheric pressure plasma sources into an analytical mass spectrometer. Methodologies and basic concepts of inductively coupled plasma mass spectrometry (ICP-MS) are emphasized in the discussion, including ion source, sampling interface, supersonic expansion, slumming process, ion optics and beam focusing, and vacuum considerations. Some new developments and innovative designs are introduced. The plasma extraction process in ICP-MS was investigated by Langmuir measurements in the region between the skimmer and first ion lens. Electron temperature (T e ) is in the range 2000--11000 K and changes with probe position inside an aerosol gas flow. Electron density (n e ) is in the range 10 8 --10 10 -cm at the skimmer tip and drops abruptly to 10 6 --10 8 cm -3 near the skimmer tip and drops abruptly to 10 6 --10 8 cm -3 downstream further behind the skimmer. Electron density in the beam leaving the skimmer also depends on water loading and on the presence and mass of matrix elements. Axially resolved distributions of electron number-density and electron temperature were obtained to characterize the ion beam at a variety of plasma operating conditions. The electron density dropped by a factor of 101 along the centerline between the sampler and skimmer cones in the first stage and continued to drop by factors of 10 4 --10 5 downstream of skimmer to the entrance of ion lens. The electron density in the beam expansion behind sampler cone exhibited a 1/z 2 intensity fall-off (z is the axial position). An second beam expansion originated from the skimmer entrance, and the beam flow underwent with another 1/z 2 fall-off behind the skimmer. Skimmer interactions play an important role in plasma extraction in the ICP-MS instrument

  19. Development of an oil skimming and separating system to combat oil spills at sea

    Energy Technology Data Exchange (ETDEWEB)

    Klimek, R.; Clauss, G.

    1983-02-01

    For efficiently combatting oil pollution at sea, it is intended to combine a hopper dredger with two oil skimmers. This system consists of two oil skimmers, which are permanently stowed on deck of the ship. In case of operation, the oil skimmers work connected beside the ship, but decoupled from the ship concerning motions of sea. Hopper dredgers have already sufficient pump and tank capacity and are well-suited for operation in offshore areas and river deltas. They are characterized by low draught and are capable of lightening their cargo very quickly so that they are ready for oil skimming operation within 2 hours. Model tests with regard to the behaviour and function of the oil skimmer system were carried out at scales of 1:15, 1:10, and 1:5. Tests with the system ship/oil skimmer were performed at a scale of 1:15.

  20. Discovery of riblets in a bird beak (Rynchops) for low fluid drag.

    Science.gov (United States)

    Martin, Samuel; Bhushan, Bharat

    2016-08-06

    Riblet structures found on fast-swimming shark scales, such as those found on a mako shark, have been shown to reduce fluid drag. In previous experimental and modelling studies, riblets have been shown to provide drag reduction by lifting vortices formed in turbulent flow, decreasing overall shear stresses. Skimmer birds (Rynchops) are the only birds to catch fish in flight by flying just above the water surface with a submerged beak to fish for food. Because they need to quickly catch prey, reducing drag on their beak is advantageous. For the first time, riblet structures found on the beak of the skimmer bird have been studied experimentally and computationally for low fluid drag properties. In this study, skimmer replicas were studied for drag reduction through pressure drop in closed-channel, turbulent water flow. Pressure drop measurements are compared for black and yellow skimmer beaks in two configurations, and mako shark skin. In addition, two configurations of skimmer beak were modelled to compare drag properties and vortex structures. Results are discussed, and a conceptual model is presented to explain a possible drag reduction mechanism in skimmers.This article is part of the themed issue 'Bioinspired hierarchically structured surfaces for green science'. © 2016 The Author(s).

  1. Mechanical recovery of oil in ice

    International Nuclear Information System (INIS)

    Solsberg, L.B.; McGrath, M.

    1992-01-01

    A literature review was performed on the mechanical systems used for removing oil in ice. The most promising spill cleanup techniques were identified along with recommendations for future work. Catalogued data in the review focused on skimmers, of which rope mop machines were considered as having the most versatile approach. The performance of the Foxtail VAB 8-14 skimmer was then assessed in North Slope crude oil and diesel fuel at a test site in Alaska. The skimmer operates through a remote power pack and pump, and incorporates eight vertically oriented rope mops. It weighs 900 kg and is suspended from a crane when deployed. Three independent test parameters were measured: oil type, slick thickness, and ice cover. A test strategy was devised to isolate the effects of individual parameters on skimming in order to optimize machine performance. Skimmer performance was based on the percent oil in the recovered oil/water mixture and the net oil collection rate. Skimmer performance was found to be optimal at rope mop speeds of 0.2-0.3 m/s in medium range viscosity oils. The unit tested was significantly less effective in diesel. Overall, the Foxtail skimmer was found to comprise an oil recovery concept that has excellent potential and affords versatility for many oil-in-ice applications. 4 figs., 1 tab

  2. Oil slick skimmer

    International Nuclear Information System (INIS)

    Karterman, D.S.

    1993-01-01

    A craft for removing an oil slick from a body of water is described comprising: a pair of spacedly arranged paralleled positioned elongated floats, a platform mounted on and extending between said floats, a weir mounted on said platform between said floats and being movable independently and substantially vertical of the longitudinal axis of said floats to a position below the surface of said body of water, a submersible oil receiving and storage means detachedly mounted to said platform between said floats and having an inlet port at one level and comprising a substantially enclosed oil accumulator having an outlet port at a lower level, said weir comprising a sluice gate constructed and arranged to admit into said inlet port of said oil receiving and storage means under the effects of gravity a portion of an oil stick comprising a water and oil mixture skimmed from said body of water, and a first pump connected to said outlet port of said accumulator to control the movement of water from the inside lower level of said accumulator out of said accumulator to thereby control the amount of the oil slick flowing into said accumulator

  3. 78 FR 9024 - Sea Turtle Conservation; Shrimp Trawling Requirements

    Science.gov (United States)

    2013-02-07

    ... restriction and require all skimmer trawls, pusher-head trawls, and wing nets (butterfly trawls) rigged for... purposes of this notice, skimmer trawls, pusher-head trawls, and wing nets (butterfly trawls) will be... trawls, pusher-head trawls, and wing nets (butterfly trawls) in the Gulf of Mexico to use TEDs in their...

  4. Heavy Oil Recovery Ohmsett Test Report

    Science.gov (United States)

    2012-06-01

    U.S. The first phase of separation is to refloat the oil for physical collection using a conveyor belt or rope mop oil skimmer. The open discharge is...inverted cone-shroud installed in the Frac tank for physical collection using a conveyor belt or rope mop oil skimmer. Heavy Oil Recovery Ohmsett Test...develop and test viable designs for systems which can detect and recover oil from subsurface environments. This is the second major report within this

  5. Assessment of the TRANSREC-350 mechanical recovery capacity of the oil spill response equipment in Prince William Sound

    International Nuclear Information System (INIS)

    Provant, S.G.

    1992-01-01

    Studies were conducted to determine the compliance of oil spill response equipment in Prince William Sound, Alaska, to state standards. Data on the observed performance of the Framo TRANSREC skimmer, which represents a large portion of the initial response skimming capability of the Sound's equipment, were obtained from Norwegian experience. The results of the analysis are based on the level of performance expected from well-trained skimmer crews responding to a 300,000 bbl spill under the worst average weather conditions over a 72-h period. Certain assumptions are made about volumes of evaporation and decanting. Results indicate that the volume of oil expected to be recovered would be 188,900 bbl, which would expand via emulsion formation to 303,000 bbl. In addition, a volume of free water would be taken in with the emulsion, which would be reduced by decanting. The overall storage capacity needed would then be 382,300 bbl. With the present available configuration of skimmers and barges, the maximum available storage capacity is 370,000 bbl. Skimmer capability can be maximized by matching storage capacity to recovery capability or by developing and demonstrating a capability to offload the recovered oil effectively such that transfer operations do not materially affect recovery operations. Recommendations are made for spill response organizations to improve their operations. 4 refs., 9 figs

  6. Fipronil application on rice paddy fields reduces densities of common skimmer and scarlet skimmer

    Science.gov (United States)

    Kasai, Atsushi; Hayashi, Takehiko I.; Ohnishi, Hitoshi; Suzuki, Kazutaka; Hayasaka, Daisuke; Goka, Koichi

    2016-01-01

    Several reports suggested that rice seedling nursery-box application of some systemic insecticides (neonicotinoids and fipronil) is the cause of the decline in dragonfly species noted since the 1990s in Japan. We conducted paddy mesocosm experiments to investigate the effect of the systemic insecticides clothianidin, fipronil and chlorantraniliprole on rice paddy field biological communities. Concentrations of all insecticides in the paddy water were reduced to the limit of detection within 3 months after application. However, residuals of these insecticides in the paddy soil were detected throughout the experimental period. Plankton species were affected by clothianidin and chlorantraniliprole right after the applications, but they recovered after the concentrations decreased. On the other hand, the effects of fipronil treatment, especially on Odonata, were larger than those of any other treatment. The number of adult dragonflies completing eclosion was severely decreased in the fipronil treatment. These results suggest that the accumulation of these insecticides in paddy soil reduces biodiversity by eliminating dragonfly nymphs, which occupy a high trophic level in paddy fields. PMID:26979488

  7. Spill response trade-offs in a very large spill

    International Nuclear Information System (INIS)

    Schulze, R.

    1990-01-01

    This paper examines the physical limitaions on spill encounter rate and how these limitaions affect the are that can be covered in spill response. Since mechanical recovery devices may not be able to cover the affected area in a large spill, in situ burning must be considered as a response option. Further, effective recovered oil logistics is essential to successful response operations and keeping skimmers operating. A successful spill response effort in a very large oil spill often depends on: Prompt response, Skimmer encounter rate, Making a decision for in situ burning, Recovered oil logistics

  8. Combined cooling and purification system for nuclear reactor spent fuel pit, refueling cavity, and refueling water storage tank

    Science.gov (United States)

    Corletti, Michael M.; Lau, Louis K.; Schulz, Terry L.

    1993-01-01

    The spent fuel pit of a pressured water reactor (PWR) nuclear power plant has sufficient coolant capacity that a safety rated cooling system is not required. A non-safety rated combined cooling and purification system with redundant branches selectively provides simultaneously cooling and purification for the spent fuel pit, the refueling cavity, and the refueling water storage tank, and transfers coolant from the refueling water storage tank to the refueling cavity without it passing through the reactor core. Skimmers on the suction piping of the combined cooling and purification system eliminate the need for separate skimmer circuits with dedicated pumps.

  9. Differential Power Analysis as a digital forensic tool.

    Science.gov (United States)

    Souvignet, T; Frinken, J

    2013-07-10

    Electronic payment fraud is considered a serious international crime by Europol. An important part of this fraud comes from payment card data skimming. This type of fraud consists of an illegal acquisition of payment card details when a user is withdrawing cash at an automated teller machine (ATM) or paying at a point of sale (POS). Modern skimming devices, also known as skimmers, use secure crypto-algorithms (e.g. Advanced Encryption Standard (AES)) to protect skimmed data stored within their memory. In order to provide digital evidence in criminal cases involving skimmers, law enforcement agencies (LEAs) must retrieve the plaintext skimmed data, generally without having knowledge of the secret key. This article proposes an alternative to the current solution at the Bundeskriminalamt (BKA) to reveal the secret key. The proposed solution is non-invasive, based on Power Analysis Attack (PAA). This article first describes the structure and the behaviour of an AES skimmer, followed by the proposal of the full operational PAA process, from power measurements to attack computation. Finally, it presents results obtained in several cases, explaining the latest improvements and providing some ideas for further developments. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

  10. Renovate produced-water-treating facilities to handle increased water cuts

    International Nuclear Information System (INIS)

    Murti, D.G.K.; Al-Nuaimi, H.R.

    1991-01-01

    This paper reports on the modified skimmer tanks that have consistently demonstrated superior oil recovery characteristics compared to conventional design in an oil field tank battery system. The modified tanks have been in continuous service for more than 3 years in one of the oldest oil fields in the Arabian Gulf. The new design has helped recover skimmed oil from a mere 6 bpd (1.0 m 3 ) to more than 55 bpd (8.75 m 3 ) from produced water in a tank battery system alone. The recovery is expected to improve by up to 200 bpd (31.8 m 3 ) once skimmer tanks in all the tank batteries are upgraded to the new design

  11. 77 FR 38266 - Sea Turtle Conservation; Shrimp Trawling Requirements; Public Hearing

    Science.gov (United States)

    2012-06-27

    ... withdraw the alternative tow time restriction and require all skimmer trawls, pusher-head trawls, and wing nets (butterfly trawls) rigged for fishing to use turtle excluder devices (TEDs) in their nets, which...

  12. Connection of a He-jet recoil transport system to an ion source

    International Nuclear Information System (INIS)

    Sheppard, G.A.

    1977-02-01

    In an effort to make non-gaseous fission products available for on-line separation and study with the TRISTAN facility, an investigation of the operational characteristics of a He-jet recoil transport system and a TRISTAN-type ion source was conducted after interfacing them with a skimmer. So that experimental results could be understood and controlled, studies of the dynamics of choked flow in a capillary and of the transport characteristics were made. Satisfactory performance of the He-jet system was obtained, but large temperature and pressure gradients thwarted early attempts to efficiently couple the He-jet to the ion source. The pressure-related difficulties have been overcome by employing a skimmer to remove extraneous gases before injection of the activities into the ion source, but efforts to conquer the temperature-related problems continue

  13. Basic studies of a gas-jet-coupled ion source for on-line isotope separation

    International Nuclear Information System (INIS)

    Anderl, R.A.; Novick, V.J.; Greenwood, R.C.

    1980-01-01

    A hollow-cathode ion source was used in a gas-jet-coupled configuration to produce ion beams of fission products transported to it from a 252 Cf fission source. Solid aerosols of NaCl and Ag were used effectively as activity carriers in the gas-jet system. Flat-plate skimmers provided an effective coupling of the ion source to the gas jet. Ge(Li) spectrometric measurements of the activity deposited on an ion-beam collector relative to that deposited on a pre-skimmer collector were used to obtain separation efficiencies ranging from 0.1% to > 1% for Sr, Y, Tc, Te, Cs, Ba, Ce, Pr, Nd and Sm. The use of CCl 4 as a support gas resulted in a significant enhancement of the alkaline-earth and rare-earth separation efficiencies

  14. Organizing export strategies.

    OpenAIRE

    G. Lojacono; M. Venzin

    2014-01-01

    The article unfolds as follows: after a brief introduction on the relevance of international trade and the characteristics of export strategies, we describe four distinct archetypes: export manager, centralistic export developer, export skimmer, integrated export developer.

  15. Recovery of light nonaqueous-phase liquids without groundwater pumping

    International Nuclear Information System (INIS)

    Markley, D.E.; Prince-Larsen, N.

    1995-01-01

    This paper outlines recovery of light nonaqueous-phase liquids (LNAPL) encountered in the subsurface at a remote natural gas facility. Remediation of LNAPL in the subsurface usually begins with dual pumping of LNAPL and groundwater. However, regulations required that only LNAPL be recovered. Methods were sought for recovering LNAPL from groundwater without pumping groundwater to the surface. Alternative methods of LNAPL recovery, using a variety of skimming pumps, included: LNAPL recovery from large-diameter wells; LNAPL recovery from trenches; LNAPL recovery from small-diameter wells; and vacuum-enhanced recovery of LNAPL while skimming with a belt skimmer. Based on the goals of the site owner and the costs associated with each alternative examined, the recommended method for recovering LNAPL without groundwater pumping was recovery of LNAPL while skimming with a belt skimmer. This paper discusses both the advantages and limitations of this technique

  16. Gas dynamics considerations in a non-invasive profile monitor for charged particle beams

    CERN Document Server

    Tzoganis, Vasilis; Welsch, Carsten P

    2014-01-01

    A non-invasive, gas jet-based, beam profile monitor has been developed in the QUASAR Group at the Cockcroft Institute, UK. This allows on-line measurement of the 2-dimensional transverse profile of particle beams with negligible disturbance to either primary beam or accelerator vacuum. The monitor is suitable for use with beams across a wide range of energies and intensities. In this setup a nozzle-skimmer system shapes a thin supersonic gas jet into a curtain. However, the small dimensions of the gas inlet nozzle and subsequent skimmers were shown to be the cause of many operational problems. In this paper, the dynamics of gas jet formation transport and shaping is discussed before an image-processing based alignment technique is introduced. Furthermore, experimental results obtained with a 5 keV electron beam are discussed and the effects of gas stagnation pressure on the acquired beam are presented.

  17. 40 CFR 112.8 - Spill Prevention, Control, and Countermeasure Plan requirements for onshore facilities (excluding...

    Science.gov (United States)

    2010-07-01

    ... exhaust lines through a settling tank, skimmer, or other separation or retention system. (8) Engineer or... located outside containment walls or where tank truck discharges may occur outside the loading area) to.... (2) Construct all bulk storage tank installations (except mobile refuelers and other non...

  18. Absolute intensities of supersonic beams

    International Nuclear Information System (INIS)

    Beijerinck, H.C.W.; Habets, A.H.M.; Verster, N.F.

    1977-01-01

    In a molecular beam experiment the center-line intensity I(0) (particles s -1 sterad -1 ) and the flow rate dN/dt (particles s -1 ) of a beam source are important features. To compare the performance of different types of beam sources the peaking factor, kappa, is defined as the ratio kappa=π(I(0)/dN/dt). The factor π is added to normalize to kappa=1 for an effusive source. The ideal peaking factor for the supersonic flow from a nozzle follows from continuum theory. Numerical values of kappa are available. Experimental values of kappa for an argon expansion are presented in this paper, confirming these calculations. The actual center-line intensity of a supersonic beam source with a skimmer is reduced in comparison to this ideal intensity if the skimmer shields part of the virtual source from the detector. Experimental data on the virtual source radius are given enabling one to predict this shielding quantitatively. (Auth.)

  19. The effect of varying air injection rates on tall oil soap skimming efficiency for low fatty acid/resin acid ratio soaps produced by pulping mountain pine beetle-infected wood

    Energy Technology Data Exchange (ETDEWEB)

    Uloth, V.; Guy, E. [FPInnovations, Prince George, BC (Canada). PAPRICAN Div.

    2009-07-01

    This study was conducted to assess the impact of higher air injection rates on the skimmer performance of an evaporator soap skimmer at a mill in British Columbia (BC). Tests previously indicated that only 13 to 38 percent of the total soap in the feed liquor was skimmed for low acid number and low fatty acid and resin acid ratio soaps. A 2-day trial demonstrated that there were extended periods when soap skimming stopped completely and soap levels in the liquor equalled or exceeded levels observed in the feed liquor. Higher air injection rates had little impact on soap-skimming efficiency. The higher air injection rates decreased soap density by approximately 8 percent, and increased black liquor entrainment in the skimmed soap by approximately 35 percent. The use of higher air injection rates was not recommended, as high percentages of black liquor are known to cause high H{sub 2}S emissions during soap acidulation. 16 refs., 1 tab., 5 figs.

  20. Modeling and experiments on differential pumping in linear plasma generators operating at high gas flows

    NARCIS (Netherlands)

    Eck, van H.J.N.; Koppers, W.R.; Rooij, van G.J.; Goedheer, W.J.; Engeln, R.A.H.; Schram, D.C.; Lopes Cardozo, N.J.; Kleyn, A.W.

    2009-01-01

    The direct simulation Monte Carlo (DSMC) method was used to investigate the efficiency of differential pumping in linear plasma generators operating at high gas flows. Skimmers are used to separate the neutrals from the plasma beam, which is guided from the source to the target by a strong axial

  1. 40 CFR 112.12 - Spill Prevention, Control, and Countermeasure Plan requirements.

    Science.gov (United States)

    2010-07-01

    ... exhaust lines through a settling tank, skimmer, or other separation or retention system. (8) Engineer or... potential for a discharge (such as where piping is located outside containment walls or where tank truck... conditions of storage such as pressure and temperature. (2) Construct all bulk storage tank installations...

  2. 76 FR 58649 - Endangered and Threatened Wildlife and Plants; 12-Month Finding on a Petition To List Van Rossem...

    Science.gov (United States)

    2011-09-21

    .... FOR FURTHER INFORMATION CONTACT: Jim Bartel, Field Supervisor, Carlsbad Fish and Wildlife Office, 6010... elegans) (Collins et al. 1991, pp. 393-395) and the black skimmer (Rynchops niger) (Palacios and Alfaro 1992, pp. 173-176; Collins and Garrett 1996, pp. 127-135; Danemann and Carmona 2000, p. 197). Black...

  3. NOFI oil Vee-Sweep and extension boom test at OHMSETT

    International Nuclear Information System (INIS)

    Bitting, K.R.; Vicedomine, J.

    1993-01-01

    The NOFI Vee-Sweep is an inflatable oil collection boom held in a V configuration by cross netting attached to the skirt of the boom. The NOFI 600S is an inflatable oil boom used to divert oil into the Vee-Sweep. The lower section of the 600S skirt consists of a feather net and a ballast chain. The booms are designed for open-ocean skimming where a skimmer is placed in the Vee-Sweep apex to remove the collected oil. During testing, the booms were preloaded with oil and towed in the OHMSETT tank at various speeds and wave conditions. Each boom was tested for its first and gross (continuous) oil loss speeds. The Vee-Sweep was also evaluated for wave performance, oil thickness vs tow speed, oil loss rate, and critical tow speed. Finally, a DESMI-250 oil skimmer was placed in the Vee-Sweep apex and oil loss tests were run while the skimmer was operating. During the critical tow speed testing, failures occurred due to apex submergence at ca 3.5 knots in calm water and short-crested waves, and 2.4 knots in harbor chop. The oil loss tests showed that the Vee-Sweep retains oil at speeds significantly higher than conventional booms. First oil loss speeds ranged from 1.3 knots in calm water to 1.0 knot in regular waves. The Vee-Sweep's high buoyancy/weight ratio gave it good wave performance in all conditions tested. The 600S oil loss speeds were higher than those of most conventional booms, and performance was better when the feather net was attached. 1 ref., 4 figs., 4 tabs

  4. Low-cost wave characterization modules for oil spill response

    Directory of Open Access Journals (Sweden)

    E.D. Skinner

    2018-06-01

    Full Text Available Marine oil spills can be remediated by mechanical skimmers in calm waters, but performance degrades with increased wave height. We have developed and demonstrated a system that quantifies local wave characteristics with an uncertainty of four inches of heave. Our system is intended for the measurement of wave characteristics during oil spill recovery. It conveys this information to coordinators and responders in real time via WiFi and remote reporting through a satellite network. This information will allow for enhanced situational awareness during an oil spill response, assisting stakeholders and optimizing mechanical skimming operations. Our wave characterization module (WCM uses accelerometer outputs from a very small inertial measurement unit (IMU to generate wave statistics and calculate wave characteristics. It is configured such that a WCM can either be attached to a skimmer float or incorporated into a microbuoy. Wave height and period are transmitted via WiFi and/or a satellite-enabled mesh-grid network to a cloud-hosted geographic information system (GIS. Here, we discuss the bare-bones sensors-plus-algorithm approach we developed by using spring-mass systems to approximate the wave height and period regime of interest. We then describe open water tests carried out using that development system both mounted to a weir skimmer mockup and packaged in a microbuoy. Finally, we present controlled tests in the wave tank at Ohmsett, the National Oil Spill Response Test Facility in New Jersey, with the WCMs communicating the wave characteristics via WiFi to tankside laptops and via satellite to the cloud-based GIS. Snapshot determinations of wave height calculated using the scalar magnitude of the three-axis accelerometer in the IMU were within four inches of the benchmark wave measurement system at Ohmsett. Keywords: Oil spill, Wave characterization module, Inertial measurement unit, Microbuoy

  5. A sextupole ion beam guide to improve the efficiency and beam quality at IGISOL

    International Nuclear Information System (INIS)

    Karvonen, P.; Moore, I.D.; Sonoda, T.; Kessler, T.; Penttilae, H.; Peraejaervi, K.; Ronkanen, P.; Aystoe, J.

    2008-01-01

    The laser ion source project at the IGISOL facility, Jyvaeskylae, has motivated the development and construction of an rf sextupole ion beam guide (SPIG) to replace the original skimmer electrode. The SPIG has been tested both off-line and on-line in proton-induced fission, light-ion and heavy-ion induced fusion-evaporation reactions and, in each case, has been directly compared to the skimmer system. For both fission and light-ion induced fusion, the SPIG has improved the mass-separated ion yields by a factor of typically 4-8. Correspondingly, the transmission efficiency of both systems has been studied in simulations with and without space charge effects. The transport capacity of the SPIG has been experimentally determined to be ∼10 12 ions s -1 before space charge effects start to take effect. A direct comparison with the simulation has been made using data obtained via light-ion fusion evaporation. Both experiment and simulation show an encouraging agreement as a function of current extracted from the ion guide.

  6. Institutionalizing Emerging Technology Assessment Process into National Incident Response

    Science.gov (United States)

    2013-10-01

    mechanical methods, devices, and products, including oil sensors, booms, skimmers, decontamination , and waste minimization technologies...handling). • Alternative Oil Spill Response Technologies (in situ burning , dispersants, etc.). • Oil Spill Damage Assessment and Restoration. The TETs...deaths of eleven crewmembers and a subsequent uncontrolled oil spill that tested the government’s ability to respond to a spill of this magnitude as

  7. The Elevation of LC-ESI-Q-TOF-MS Response in the Analysis of Isoquinoline Alkaloids from Some Papaveraceae and Berberidaceae Representatives.

    Science.gov (United States)

    Kukula-Koch, Wirginia

    2017-01-01

    Twenty-five methanol extracts obtained from various representatives of Papaveraceae and Berberidaceae botanical families (genera: Papaver , Argemone , Eschscholzia , Chelidonium , Glaucium , and Berberis ) were screened for their alkaloid content in an optimized method suitable for the LC-ESI-Q-TOF-MS analysis. Twelve pharmacologically important isoquinoline alkaloids from four groups, aporphines, benzylisoquinolines, protoberberines, and benzophenanthridines, present in these traditionally used plant species were quantitatively determined in each studied sample, providing their alkaloid profile. A Zorbax Stable Bond RP-18 column and a mobile phase composed of 0.1% formic acid and 0.1% formic acid in acetonitrile (v/v) were used at the flow rate of 0.2 mL/min. A profound study on the optimization of MS response to four groups of isoquinoline alkaloids (validation of capillary voltage, gas flows, nebulizer pressure, skimmer, and fragmentor voltages), repeatability of results, and stability and linearity of measurements were described, showing, among others, 3000 V of capillary voltage, 350°C of gas temperature, 12 L/min of gas flows, nebulizer pressure of 35 psig, 65 V for skimmer voltage, and 30 V for collision energy as the most advantageous operation parameters.

  8. The Elevation of LC-ESI-Q-TOF-MS Response in the Analysis of Isoquinoline Alkaloids from Some Papaveraceae and Berberidaceae Representatives

    Directory of Open Access Journals (Sweden)

    Wirginia Kukula-Koch

    2017-01-01

    Full Text Available Twenty-five methanol extracts obtained from various representatives of Papaveraceae and Berberidaceae botanical families (genera: Papaver, Argemone, Eschscholzia, Chelidonium, Glaucium, and Berberis were screened for their alkaloid content in an optimized method suitable for the LC-ESI-Q-TOF-MS analysis. Twelve pharmacologically important isoquinoline alkaloids from four groups, aporphines, benzylisoquinolines, protoberberines, and benzophenanthridines, present in these traditionally used plant species were quantitatively determined in each studied sample, providing their alkaloid profile. A Zorbax Stable Bond RP-18 column and a mobile phase composed of 0.1% formic acid and 0.1% formic acid in acetonitrile (v/v were used at the flow rate of 0.2 mL/min. A profound study on the optimization of MS response to four groups of isoquinoline alkaloids (validation of capillary voltage, gas flows, nebulizer pressure, skimmer, and fragmentor voltages, repeatability of results, and stability and linearity of measurements were described, showing, among others, 3000 V of capillary voltage, 350°C of gas temperature, 12 L/min of gas flows, nebulizer pressure of 35 psig, 65 V for skimmer voltage, and 30 V for collision energy as the most advantageous operation parameters.

  9. Bag filters at biofuelled plants, reliability and economy of operation; Slangfilter vid bioeldade anlaeggningar, tillfoerlitlighet och driftsekonomi

    Energy Technology Data Exchange (ETDEWEB)

    Lindau, Leif [SYCON Energikonsult, Malmoe (Sweden)

    2002-04-01

    The background to this work is the increased requirements on dust emission control for smaller (2-50 MW) biofuel plants in Sweden, where established technology consisting of multi cyclones cannot meet the emission demands, and where the specific cost of the large scale established technology (electrostatic precipitators) quickly increases with decreased plant size. Operational experience of bag filters on Swedish biofuel plants down to a size of 2 MW has been collected. The operational experience is remarkably uniform and positive and availability is high. Bag life, being the most important operational cost factor, is between two and eleven years. Most frequent material used is aramide, but also PPS is employed and the experience of both materials is good. The cost relation between bag filter (including an upstream skimmer) and electrostatic precipitator has been studied based on supplier quotations. Bag filter always has the lowest first cost. At one year bag life, the total cost of a bag filter is less than that for an electrostatic precipitator for plants smaller than 15 MW, and at more than one year's bag life, the bag filter has the lowest total cost for plants up to 50 MW. For plants smaller than 5-10 MW, the difference in total cost is very high. With some simple means for quality assurance of new bags, premature failure rate can be reduced. Following up cleaning interval and/or emission during operation time, gives information about the development of bag condition and necessary bag change can be foreseen. Since bag filters are more prone to damage by fire than electrostatic precipitators, the process of damage due to entrained sparks has been analysed based on practical observations and a thermal calculation. This consideration shows that this damage mode can be eliminated by an upstream skimmer having moderate but reliable performance. The result is well in coherence with the practical operational experience found that with an adequate skimmer

  10. Investigation into the behavior of metal-argon polyatomic ions (MAr+) in the extraction region of inductively coupled plasma-mass spectrometry

    International Nuclear Information System (INIS)

    Ebert, Chris H.; Witte, Travis M.; Houk, R.S.

    2012-01-01

    The abundances of metal-argon polyatomic ions (MAr + ) are determined in inductively coupled plasma-mass spectrometry (ICP-MS). The ratios of MAr + abundance to that for M + ions are measured experimentally. These ratios are compared to expected values, calculated for typical plasma conditions using spectroscopic data. For all metals studied (Ti, V, Cr, Mn, Fe, Co, Ni, Cu, and Zn), the measured ratios are significantly lower than the calculated ratios. Increasing the plasma potential (and thereby increasing the ion kinetic energy) by means of a homemade guard electrode with a wide gap further reduces the MAr + /M + ratio. Implementing a skimmer cone designed for high transmission of light ions increases the MAr + abundance. Considering this evidence, the scarcity of MAr + ions is attributed to collision induced dissociation (CID), likely due to a shock wave at the tip of or in the throat of the skimmer cone. - Highlights: ► MAr + ions are less abundant in the mass spectrum than expected from the ICP. ► Increasing the plasma potential reduces their abundance further. ► The extraction lens voltage does not greatly affect the MAr + abundances. ► The weakly-bound MAr + ions are probably dissociated by collisions during extraction.

  11. Experimental investigation of molecular beam injection in HL-1 tokamak

    International Nuclear Information System (INIS)

    Yao Lianghua; Diao Guangyao; Wang Zhanhe; Deng Huichen; Luo Junlin; Duan Xuru; Cui Zhengying

    1993-07-01

    A new method of gas puffing is presented. The molecular beam, formed by high pressure deuterium gas through Larval nozzle and skimmer slit, is injected into the HL-1 vacuum vessel. The deuterium molecular current from the nozzle passing through the skimmer is about 3 x 10 20 /s. At the line average electron density of 5.2 x 10 19 m -3 , the beam velocity is about 100 m/s. As the plasma density and temperature increasing, the influxes of deuterium particles attenuate quickly. When the molecular beam injection (MBI) just returned to normal gas puffing, the D α emission rapidly decreases, meanwhile, the particles move toward plasma center, the electron density is continuously peaking. The line average electron density rising lasts 45 ms. The thermal energy of plasma and confinement time for particles and energy are also increasing. the MBI is a direct and efficient gas fuelling mode, and the injected particles can reach to inside about 8 cm of plasma and q ≅ 2 confinement region. Its efficiency of injection is about 50%. After the MBI, the particle recycling coefficient R on the wall is 0.6 which is 10% lower than that of normal gas puffing

  12. Challenges and prospects of population genetic studies in terns (Charadriiformes, Aves

    Directory of Open Access Journals (Sweden)

    Patrícia J. Faria

    2007-01-01

    Full Text Available Little information is available about the population structure of communally nesting terns (Sternidae and skimmers (Rynchopidae throughout the world. In order to fill this gap, a survey of molecular markers was carried out for six species of terns (Anous stolidus, Sterna hirundinacea, S. fuscata, S. superciliaris, Thalasseus maximus and Phaetusa simplex and one species of skimmer (Rynchops niger. First, we describe the results of the construction of genomic DNA libraries and document problems encountered during this procedure. Secondly, we tested the cross-amplification of 18 microsatellite loci previously described for related species (the number of polymorphic loci ranged from three to seven. Thirdly, we tested the usefulness of mtDNA (control region, ND2, Cytochrome b and ATPase 6/8 for phylogeographic studies in this group of birds. The occurrence of nuclear copies of the mitochondrial control region is reported. Nucleotide divergence in the mtDNA genes analyzed ranged from 0.0 to 0.006. Despite the difficulties associated with the selection of variable markers in this group of seabirds, we were able to select polymorphic markers for each species tested and we anticipate these results will help the development of genetic studies concerning important biological questions in terns.

  13. Edible Oil Industry Wastewater Treatment by Microfiltration with Ceramic Membrane

    OpenAIRE

    Zita Šereš; Dragana Šoronja Simović; Ljubica Dokić; Lidietta Giorno; Biljana Pajin; Cecilia Hodur; Nikola Maravić

    2016-01-01

    Membrane technology is convenient for separation of suspended solids, colloids and high molecular weight materials that are present. The idea is that the waste stream from edible oil industry, after the separation of oil by using skimmers is subjected to microfiltration and the obtained permeate can be used again in the production process. The wastewater from edible oil industry was used for the microfiltration. For the microfiltration of this effluent a tubular membrane was used with a pore ...

  14. Arctic Oil Spill Response Guide for the Alaskan Beaufort Sea

    Science.gov (United States)

    1988-03-01

    skimmers. Oiled soil and debris, which could not be cleaned by this technique, was removed and placed in heavy duty plastic bags and 55-gallon drums. 6.5.9...burned in a smokeless flare burner. Oiled debris was burned in the Coast Guard Trecan Incinerator which was set up at Prudhoe Bay. Oiled soil was placed...skeletons that form diatomite . Dinoflagellates: any of an order to planktonic forms important in aquatic food chains and including forms causing red tides

  15. Multistage method and apparatus for separating substances of different atomic weights using a plasma centrifuge

    International Nuclear Information System (INIS)

    Hirshfield, J.L.; Krishnan, M.

    1986-01-01

    This invention provides a method and apparatus for separating isotopes using a plasma centrifuge; in particular, it provides a multistage method and apparatus wherein a laser-initiated vacuum arc is used to fully ionize and form a plasma of the substances to be separated. The substances to be separated are positioned in an evacuated vessel which has a longitudinal axis. A magnetic field is generated in the vessel parallel to the axis of the vessel, and a target comprised of the substances to be separated is positioned at one end of the vessel. Pulsed laser energy is focused on the substances, thereby completely ionizing at least a portion of the substances and forming a plasma. Immediately following the arrival of the laser energy, a current is passed through the substances to be separated, which causes further complete ionization. The plasma is rotated and moved from the target to the collector by the application of a magnetic field. A plurality of skimmers is positioned in the vessel between the target and the collector such that a portion of the rotating plasma strikes the skimmer and is collected thereon. The remainder of the plasma continues moving towards the collector. The material which finally strikes the collector is only a percentage of the starting material, but it is highly enriched or concentrated

  16. Investigations into the origins of polyatomic ions in inductively coupled plasma-mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    McIntyre, Sally M. [Iowa State Univ., Ames, IA (United States)

    2010-01-01

    An inductively coupled plasma-mass spectrometer (ICP-MS) is an elemental analytical instrument capable of determining nearly all elements in the periodic table at limits of detection in the parts per quadrillion and with a linear analytical range over 8-10 orders of magnitude. Three concentric quartz tubes make up the plasma torch. Argon gas is spiraled through the outer tube and generates the plasma powered by a looped load coil operating at 27.1 or 40.6 MHz. The argon flow of the middle channel is used to keep the plasma above the innermost tube through which solid or aqueous sample is carried in a third argon stream. A sample is progressively desolvated, atomized and ionized. The torch is operated at atmospheric pressure. To reach the reduced pressures of mass spectrometers, ions are extracted through a series of two, approximately one millimeter wide, circular apertures set in water cooled metal cones. The space between the cones is evacuated to approximately one torr. The space behind the second cone is pumped down to, or near to, the pressure needed for the mass spectrometer (MS). The first cone, called the sampler, is placed directly in the plasma plume and its position is adjusted to the point where atomic ions are most abundant. The hot plasma gas expands through the sampler orifice and in this expansion is placed the second cone, called the skimmer. After the skimmer traditional MS designs are employed, i.e. quadrupoles, magnetic sectors, time-of-flight. ICP-MS is the leading trace element analysis technique. One of its weaknesses are polyatomic ions. This dissertation has added to the fundamental understanding of some of these polyatomic ions, their origins and behavior. Although mainly continuing the work of others, certain novel approaches have been introduced here. Chapter 2 includes the first reported efforts to include high temperature corrections to the partition functions of the polyatomic ions in ICP-MS. This and other objections to preceeding

  17. Identifying bioaccumulative halogenated organic compounds using a nontargeted analytical approach: seabirds as sentinels.

    Directory of Open Access Journals (Sweden)

    Christopher J Millow

    Full Text Available Persistent organic pollutants (POPs are typically monitored via targeted mass spectrometry, which potentially identifies only a fraction of the contaminants actually present in environmental samples. With new anthropogenic compounds continuously introduced to the environment, novel and proactive approaches that provide a comprehensive alternative to targeted methods are needed in order to more completely characterize the diversity of known and unknown compounds likely to cause adverse effects. Nontargeted mass spectrometry attempts to extensively screen for compounds, providing a feasible approach for identifying contaminants that warrant future monitoring. We employed a nontargeted analytical method using comprehensive two-dimensional gas chromatography coupled to time-of-flight mass spectrometry (GC×GC/TOF-MS to characterize halogenated organic compounds (HOCs in California Black skimmer (Rynchops niger eggs. Our study identified 111 HOCs; 84 of these compounds were regularly detected via targeted approaches, while 27 were classified as typically unmonitored or unknown. Typically unmonitored compounds of note in bird eggs included tris(4-chlorophenylmethane (TCPM, tris(4-chlorophenylmethanol (TCPMOH, triclosan, permethrin, heptachloro-1'-methyl-1,2'-bipyrrole (MBP, as well as four halogenated unknown compounds that could not be identified through database searching or the literature. The presence of these compounds in Black skimmer eggs suggests they are persistent, bioaccumulative, potentially biomagnifying, and maternally transferring. Our results highlight the utility and importance of employing nontargeted analytical tools to assess true contaminant burdens in organisms, as well as to demonstrate the value in using environmental sentinels to proactively identify novel contaminants.

  18. A catalog of Louisiana's nesting seabird colonies

    Science.gov (United States)

    Fontenot, William R.; Cardiff, Steve W.; DeMay, Richard A.; Dittmann, Donna L.; Hartley, Stephen B.; Jeske, Clinton W.; Lorenz, Nicole; Michot, Thomas C.; Purrington, Robert Dan; Seymour, Michael; Vermillion, William G.

    2012-01-01

    Summarizing his colonial nesting waterbird survey experiences along the northern coast of the Gulf of Mexico in a paper presented to the Colonial Waterbird Group of the Waterbird Society (Portnoy 1978), bird biologist John W. Portnoy stated, “This huge concentration of nesting waterbirds, restricted almost entirely to the wetlands and estuaries of southern Louisiana, is unmatched in all of North America; for example, a 1975 inventory of wading birds along the Atlantic Coast from Maine to Florida [Custer and Osborn, in press], tallied 250,000 breeding [waterbirds] of 14 species, in contrast with the 650,000 birds of 15 species just from Sabine Pass to Mobile Bay.” The “650,000 birds” to which Portnoy referred, were tallied by him in a 1976 survey of coastal Louisiana, Mississippi, and Alabama (see below, under “Major Surveys” section). According to the National Atlas of Coastal Waterbird Colonies in the Contiguous United States: 1976-82 (Spendelow and Patton 1988), the percentages of the total U.S. populations of Laughing Gull (11%), Forster's Tern (52%), Royal Tern (16%), Sandwich Tern (77%), and Black Skimmer (44%) which annually nest in Louisiana are significant – perhaps crucially so in the cases of Forster's Tern, Sandwich Tern, and Black Skimmer. Nearly three decades after Spendelow and Patton's determinations above, coastal Louisiana still stands out as the major center of colonial wading bird and seabird nesting in all of the United States. Within those three intervening decades, however, the

  19. Capture, transport and husbandry of Naucrates ductor

    Directory of Open Access Journals (Sweden)

    Francisco De Vaissier Ferro Mauricio

    2014-06-01

    Full Text Available This is a report on the capture, transport, and husbandry of Naucrates ductor, also known as pilot fish. Approximately 100 individuals were collected by Flying Sharks in the sequence of an order from multiple public aquaria. Because there is vely limited knowledge about the capture, husbandry and transport of this species, it became necessary to investigate how to achieve this while causing minimum mortality and ensuring animal welfare. Collection was done in the Azores Islands, approximately 20 nautical miles from Horta, using a standard fishing rod and hook, after attracting blue sharks with bait. The animals were transported to shore inside plastic vats and introduced to large 2,0 m wide holding tanks at the Porto Pim Aquarium, where they were held for 2 months. Multiple treatments for wounds, and parasite control, were used and are reported. Transport to mainland Portugal was done aboard a commercial vessel, inside 2,4 m wide polyethylene vats with mechanical and chemical filtration consisting of cartridge filters and protein skimmers, respectively. Once docked on shore the 40 ft. container was then moved to a truck, where it traveled to Spain and France over 6 days. The total transport time of those animals delivered last was therefore 11 days and no mortalities were sustained in transit. The remaining animals were kept in Peniche for 2 more months inside 2,4 m wide polyethylene vats, with filtration consisting of cartridge and protein skimmers, as well as daily water changes. Multiple challenges faced during the collection, holding and transport processes are presented in this presentation.

  20. Interaction of intense electromagnetic fields with SF6 molecules and clusters in supersonic expansion

    International Nuclear Information System (INIS)

    Airoldi, V.J.T.

    1987-01-01

    A method of measuring SF 6 cluster formation and inhibition in pulsed supersonic expansion in the presence of intense electromagnetic radiation is presented. The characterization of the expansion of SF 6 molecules was done and, the extension of the collision region was determined. An improved unidimensional theory of supersonic expansion showed good agreement with the experimental results. The spectra of multiphoton absorption of SF 6 molecules in supersonic jet and the average energy absorved by each molecule were determined. The absorption spectra of molecule in the collision region present absorption maxima different from those obtained in the collisionless region. The results, if compared with the literature data, show good agreement, with a small difference in the spetra corresponding to the collisionless region. This difference was observed, for the first time in the multiphoton absorption and is attribuited to cluster formation in the jet. A new technique for measuring cluster formation in the supersonic jet, based on determination of the spatial distribution of the energy of molecules in the jet after passing through a skimmer located in the collision region is shown. The inhibition of cluster formation, due to the incidence of intense electromagnetic radiation from a CO 2 -TEA pulsed laser in the initial collision region of the jet, causes a second expansion in the skimmer. The results obtained show that this method can lead to a new isotope separation process. All the parts of the experimental set up, for example, high vacuum system, pulsed valve and pyroelectric detector, were developed and constructed specially for the experiment. (Author) [pt

  1. Quantification of nucleotides by ICPMS: coupling of ICPMS with capillary electrophoresis or capillary HPLC

    International Nuclear Information System (INIS)

    Inagaki, K.; Fujii, S.; Takatsu, A.; Yarita, T.; Zhu, Y.; Chiba, K.

    2009-01-01

    Full text: Quantification of nucleotides in small volumes of biological samples has eagerly been demanded. A method using ICPMS coupled with capillary electrophoresis or capillary liquid chromatography is reported. A new interface system, which consists of a double tube nebulizer inserted with a fused silica capillary tube and a cylinder mini-chamber with a sheath gas inlet, was designed. Moreover, the surface conditions of the sampling and skimmer cones, and the introduction of H 2 gas into the plasma were found to significantly improve the signal/background ratio for phosphorus determination at m/z 31. (author)

  2. Simple setup for gas-phase h/d exchange mass spectrometry coupled to electron transfer dissociation and ion mobility for analysis of polypeptide structure on a liquid chromatographic time scale

    DEFF Research Database (Denmark)

    Mistarz, Ulrik Hvid; Brown, Jeffery M; Haselmann, Kim F

    2014-01-01

    gas immediately upstream or downstream of the primary skimmer cone. The approach was implemented on three commercially available mass spectrometers and required no or minor fully reversible reconfiguration of gas-inlets of the ion source. Results from gas-phase HDX-MS of peptides using the aqueous ND3....../D2O as HDX reagent indicate that labeling is facilitated exclusively through gaseous ND3, yielding similar results to the infusion of purified ND3-gas, while circumventing the complications associated with the use of hazardous purified gases. Comparison of the solution-phase- and gas-phase deuterium...

  3. Numerical modelling of the jet nozzle enrichment process

    International Nuclear Information System (INIS)

    Vercelli, P.

    1983-01-01

    A numerical model was developed for the simulation of the isotopic enrichment produced by the jet nozzle process. The flow was considered stationary and under ideal gas conditions. The model calculates, for any position of the skimmer piece: (a) values of radial mass concentration profiles for each isotopic species and (b) values of elementary separation effect (Σ sub(A)) and uranium cut (theta). The comparison of the numerical results obtained with the experimental values given in the literature proves the validity of the present work as an initial step in the modelling of the process. (Author) [pt

  4. Remedial design for petroleum hydrocarbons: Soil vapor extraction, product skimmers, and air stripping

    International Nuclear Information System (INIS)

    Anastasi, F.S.; Loftin, H.J.

    1994-01-01

    Site characterization activities at an Army installation in Virginia performed prior to closure identified a significant release of gasoline from underground storage tanks and piping associated with the post exchange service station. Floating liquid-phase petroleum hydrocarbons (FLPH) observed in the subsurface over an area of approximately 80,000 square feet ranged up to 5 feet in thickness. Ground water was found to be contaminated with dissolved components of gasoline over an area of approximately 150,000 square feet. A nearby lake and adjacent streams were not impacted by either free-phase or dissolved contamination. Interim remedial measures, including pilot testing of FLPH, vapor-phase, and ground water recovery technologies, were implemented following discovery of the release. Over 5,000 gallons of free-phase product were recovered by skimming and approximately 1,450 gallons of product equivalent were recovered during pilot testing of a soil vapor extraction (SVE) system. At the conclusion of these actions, hydrocarbons remain distributed in the subsurface in the adsorbed-, dissolved-, and vapor-phase. The majority of residual on-site contamination is believed to be either adsorbed to soil particles or as FLPH. The final design of an integrated remediation system based on the pilot test results addressed these conditions

  5. Extending temporary storage capacity with emulsion breakers

    International Nuclear Information System (INIS)

    Buist, I.; Guarino, A.; DeVitis, D.; Nolan, K.; Lewis, A.; Smith, B.; Lane, J.

    2002-01-01

    The use of emulsion breakers injected into an oil spill recovery system was examined in both laboratory testing and at the OHMSETT test facility. The tests were designed to assess the injection/mixing/settling regimes needed for optimum water-removal performance from a meso-stable water-in-oil emulsion with an oil spill demulsifier. Different types of injection locations and mixing technologies were examined, including skimmer heads, cargo lines, tank inlets, as well as static in-line and mechanical technologies. During laboratory testing, water-in-oil emulsions and free water was pumped through various lengths of piping loops, an in-line mixer and 8 settling tanks. Following the injection of a demulsifier, the fluid was decanted to observe the emulsion breaking. At the OHMSETT test facility, a Desmi Terminator skimmer recovered the same emulsion from a polluted water surface. Different slick thicknesses, wave heights and recovery rates were used. A demulsifier was also injected into the recovered fluid which was allowed to separate in recovery tanks. The demulsifier efficiency was then measured. It was determined that the demulsifier significantly reduced the volume of water in the recovery tanks and the water content of the remaining emulsion. If free water content was greater than 60 per cent, then the effect of the surfactant was greatly reduced. If no free water was present, the level of turbulence was insufficient to promote emulsion breaking. More than 33 per cent free water content is needed to reduce the bulk viscosity of the fluid and to promote emulsion breaking. The degree of emulsion breaking also increased with increasing mixing energy. 10 refs., 5 tabs., 8 figs

  6. Resonance ionization in a gas cell: a feasibility study for a laser ion source

    International Nuclear Information System (INIS)

    Qamhieh, Z.N.; Vandeweert, E.; Silverans, R.E.; Duppen, P. van; Huyse, M.; Vermeeren, L.

    1992-01-01

    A laser ion source based on resonance photo-ionization in a gas cell is proposed. The gas cell, filled with helium, consists of a target chamber in which the recoil products are stopped and neutralized, and an ionization chamber where the atoms of interest are selectively ionized by the laser light. The extraction of the ions from the ionization chamber through the exit hole-skimmer setup is similar to the ion-guide system. The conditions to obtain an optimal system are given. The results of a two-step one-laser resonance photo-ionization of nickel and the first results of laser ionization in a helium buffer gas cell are presented. (orig.)

  7. Fundamental and applied measurements in ICP MS

    International Nuclear Information System (INIS)

    Carter, Julian Robert

    2002-01-01

    Fundamental and applied aspects of ICP-MS have been investigated to gain an increased understanding of the technique and improve on its analytical capabilities. Dissociation temperatures of polyatomic ions were calculated using a double-focusing sector instrument, to obtain more reliable mass spectral data with controlled vapour introduction via a Dreschel bottle to allow accurate calculation of the ingredients in the plasma. The equilibrium temperature for the plasma, operated at 1280 W calculated using CO + and C 2 + as the thermometric probes, was c.a. 5800 - 7400 K, while using ArO + and ArC + as the thermometric probes the temperature calculated was c.a. 2000 - 7000 K. Calculated dissociation temperatures were used to elucidate the site of formation of these ions. Results confirmed that strongly bound ions such as CO + and C 2 + were formed in the plasma whereas weakly bound ions such as ArO + and ArC + were formed in the interface region due to gross deviation of the calculated temperatures from those expected for a system in thermal equilibrium. The use of helium gas in a hexapole collision cell attenuated the signals of ArH + Ar + , ArO + , ArC + , ArCl + and Ar 2 + allowing improved determination of 39 K + , 40 Ca + , 56 Fe + , 52 Cr + , 75 As + and 80 Se + in standard solutions. The use of the hexapole collision cell also resulted in an enhancement of analyte signals due to the thermalisation of the ion beam. The ion kinetic energy of ions sampled from the plasma and those sampled from the skimmer cone were determined using a modified lens stack to assess the significance for memory effects of material deposited on the skimmer cone. The most probable kinetic energy of Be + ions sampled from the skimmer cone was found to be 2.4 eV, which was considerably lower than the most probable kinetic energy of Be + ions sampled from the plasma, which was found to be 9.5 eV. The low kinetic energy of the ions deposited on the skimmer cone means they will only

  8. Oil spill cleanup in severe weather and open ocean conditions

    International Nuclear Information System (INIS)

    Kowalski, T.

    1993-01-01

    Most serious oil spills occur in open water under severe weather conditions. At first the oil stays on the surface, where it is spread by winds and water currents. The action of the waves then mixes the oil into the water column. With time the light elements of crude oil evaporate. The remaining residue is of very low commercial value, but of significant environmental impact. The oil spill can move either out to sea or inshore, where it ends up on the beaches. Normal procedures are to let outbound oil disperse by evaporation and mixing into the water column, and to let the inbound oil collect on the beaches, where the cleanup operations are concentrated. The reason for this is that there is no capability to clean the surface of the water in wave conditions-present-day oil skimmers are ineffective in waves approaching 4 ft in height. It would be simpler, more effective and environmentally more beneficial to skim the oil right at the spill location. This paper describes a method to do this. In the case of an oil spill in open water and high wave conditions, it is proposed to reduce the height of the ocean waves by the use of floating breakwaters to provide a relatively calm area. In such protected areas existing oil skimmers can be used to recover valuable oil and clean up the spill long before it hits the beaches. A floating breakwater developed at the University of Rhode Island by the author can be of great benefit in oil spill cleanup for open ocean conditions. This breakwater is constructed from scrap automobile tires. It is built in units of 20 tires each, which are easily transportable and can be connected together at the spill site to form any desired configuration

  9. Skimmers, dippers, and divers : Campfire’s Steve Coulson on transmedia marketing and audience participation

    NARCIS (Netherlands)

    Hassler-Forest, Dan

    In this interview, Campfire’s creative director Steve Coulson talks about his work in activating fan communities as part of the publicity campaign for storytelling franchises. His marketing firm specializes in creating immersive experiences that encourage fans to participate in transmedia

  10. Skimmers, dippers, and divers : Campfire’s Steve Coulson on transmedia marketing and audience participation

    OpenAIRE

    Hassler-Forest, Dan

    2016-01-01

    In this interview, Campfire’s creative director Steve Coulson talks about his work in activating fan communities as part of the publicity campaign for storytelling franchises. His marketing firm specializes in creating immersive experiences that encourage fans to participate in transmedia storyworlds. Focusing the discussion on his experience on the campaign for Game of Thrones, Coulson reflects on the changing nature of fandom, the possibilities and limitations of transmedia storytelling, fa...

  11. High resolution studies of the origins of polyatomic ions in inductively coupled plasma-mass spectrometry, Part I. Identification methods and effects of neutral gas density assumptions, extraction voltage, and cone material

    International Nuclear Information System (INIS)

    Ferguson, Jill Wisnewski; Houk, R.S.

    2006-01-01

    Common polyatomic ions (ArO + , NO + , H 2 O + , H 3 O + , Ar 2 + , ArN + , OH + , ArH + , O 2 + ) in inductively coupled plasma-mass spectrometry (ICP-MS) are identified using high mass resolution and studied using kinetic gas temperatures (T gas ) determined from a dissociation reaction approach. Methods for making accurate mass measurements, confirming ion identifications, and correcting for mass bias are discussed. The effects of sampler and skimmer cone composition and extraction voltage on polyatomic ion formation are also explored. Neutral species densities at several locations in the extraction interface are estimated and the corresponding effects of the T gas value are calculated. The results provide information about the origins of background ions and indicate possible locations for their formation or removal

  12. Fundamental and applied measurements in ICP MS

    Energy Technology Data Exchange (ETDEWEB)

    Carter, Julian Robert

    2002-07-01

    Fundamental and applied aspects of ICP-MS have been investigated to gain an increased understanding of the technique and improve on its analytical capabilities. Dissociation temperatures of polyatomic ions were calculated using a double-focusing sector instrument, to obtain more reliable mass spectral data with controlled vapour introduction via a Dreschel bottle to allow accurate calculation of the ingredients in the plasma. The equilibrium temperature for the plasma, operated at 1280 W calculated using CO{sup +} and C{sub 2}{sup +} as the thermometric probes, was c.a. 5800 - 7400 K, while using ArO{sup +} and ArC{sup +} as the thermometric probes the temperature calculated was c.a. 2000 - 7000 K. Calculated dissociation temperatures were used to elucidate the site of formation of these ions. Results confirmed that strongly bound ions such as CO{sup +} and C{sub 2}{sup +} were formed in the plasma whereas weakly bound ions such as ArO{sup +} and ArC{sup +} were formed in the interface region due to gross deviation of the calculated temperatures from those expected for a system in thermal equilibrium. The use of helium gas in a hexapole collision cell attenuated the signals of ArH{sup +} Ar{sup +}, ArO{sup +}, ArC{sup +}, ArCl{sup +} and Ar{sub 2}{sup +} allowing improved determination of {sup 39}K{sup +}, {sup 40}Ca{sup +}, {sup 56}Fe{sup +}, {sup 52}Cr{sup +}, {sup 75}As{sup +} and {sup 80}Se{sup +} in standard solutions. The use of the hexapole collision cell also resulted in an enhancement of analyte signals due to the thermalisation of the ion beam. The ion kinetic energy of ions sampled from the plasma and those sampled from the skimmer cone were determined using a modified lens stack to assess the significance for memory effects of material deposited on the skimmer cone. The most probable kinetic energy of Be{sup +} ions sampled from the skimmer cone was found to be 2.4 eV, which was considerably lower than the most probable kinetic energy of Be{sup +} ions

  13. Endocranial anatomy of the charadriiformes: sensory system variation and the evolution of wing-propelled diving.

    Directory of Open Access Journals (Sweden)

    N Adam Smith

    Full Text Available Just as skeletal characteristics provide clues regarding behavior of extinct vertebrates, phylogenetically-informed evaluation of endocranial morphology facilitates comparisons among extinct taxa and extant taxa with known behavioral characteristics. Previous research has established that endocranial morphology varies across Aves; however, variation of those systems among closely related species remains largely unexplored. The Charadriiformes (shorebirds and allies are an ecologically diverse clade with a comparatively rich fossil record, and therefore, are well suited for investigating interspecies variation, and potential links between endocranial morphology, phylogeny, ecology and other life history attributes. Endocranial endocasts were rendered from high resolution X-ray computed tomography data for 17 charadriiforms (15 extant and two flightless extinct species. Evaluation of endocranial character state changes on a phylogeny for Charadriiformes resulted in identification of characters that vary in taxa with distinct feeding and locomotor ecologies. In comparison with all other charadriiforms, stem and crown clade wing-propelled diving Pan-Alcidae displayed compressed semicircular canals, and indistinct occipital sinuses and cerebellar fissures. Flightless wing-propelled divers have relatively smaller brains for their body mass and smaller optic lobes than volant pan-alcids. Observed differences between volant and flightless wing-propelled sister taxa are striking given that flightless pan-alcids continue to rely on the flight stroke for underwater propulsion. Additionally, the brain of the Black Skimmer Rynchops niger, a taxon with a unique feeding ecology that involves continuous forward aerial motion and touch-based prey detection used both at day and night, is discovered to be unlike that of any other sampled charadriiform in having an extremely large wulst as well as a small optic lobe and distinct occipital sinus. Notably, the

  14. In situ sulfur isotopes (δ{sup 34}S and δ{sup 33}S) analyses in sulfides and elemental sulfur using high sensitivity cones combined with the addition of nitrogen by laser ablation MC-ICP-MS

    Energy Technology Data Exchange (ETDEWEB)

    Fu, Jiali [State Key Laboratory of Geological Processes and Mineral Resources, China University of Geosciences, Wuhan 430074 (China); Hu, Zhaochu, E-mail: zchu@vip.sina.com [State Key Laboratory of Geological Processes and Mineral Resources, China University of Geosciences, Wuhan 430074 (China); The Beijing SHRIMP Center, Institute of Geology, Chinese Academy of Geological Sciences, Beijing 102206 (China); Zhang, Wen [State Key Laboratory of Geological Processes and Mineral Resources, China University of Geosciences, Wuhan 430074 (China); Yang, Lu [State Key Laboratory of Geological Processes and Mineral Resources, China University of Geosciences, Wuhan 430074 (China); National Research Council Canada, 1200 Montreal Rd., Ottawa, Ontario K1A 0R6 (Canada); Liu, Yongsheng; Li, Ming; Zong, Keqing; Gao, Shan; Hu, Shenghong [State Key Laboratory of Geological Processes and Mineral Resources, China University of Geosciences, Wuhan 430074 (China)

    2016-03-10

    The sulfur isotope is an important geochemical tracer in diverse fields of geosciences. In this study, the effects of three different cone combinations with the addition of N{sub 2} on the performance of in situ S isotope analyses were investigated in detail. The signal intensities of S isotopes were improved by a factor of 2.3 and 3.6 using the X skimmer cone combined with the standard sample cone or the Jet sample cone, respectively, compared with the standard arrangement (H skimmer cone combined with the standard sample cone). This signal enhancement is important for the improvement of the precision and accuracy of in situ S isotope analysis at high spatial resolution. Different cone combinations have a significant effect on the mass bias and mass bias stability for S isotopes. Poor precisions of S isotope ratios were obtained using the Jet and X cones combination at their corresponding optimum makeup gas flow when using Ar plasma only. The addition of 4–8 ml min{sup −1} nitrogen to the central gas flow in laser ablation MC-ICP-MS was found to significantly enlarge the mass bias stability zone at their corresponding optimum makeup gas flow in these three different cone combinations. The polyatomic interferences of OO, SH, OOH were also significantly reduced, and the interference free plateaus of sulfur isotopes became broader and flatter in the nitrogen mode (N{sub 2} = 4 ml min{sup −1}). However, the signal intensity of S was not increased by the addition of nitrogen in this study. The laser fluence and ablation mode had significant effects on sulfur isotope fractionation during the analysis of sulfides and elemental sulfur by laser ablation MC-ICP-MS. The matrix effect among different sulfides and elemental sulfur was observed, but could be significantly reduced by line scan ablation in preference to single spot ablation under the optimized fluence. It is recommended that the d{sub 90} values of the particles in pressed powder pellets for accurate

  15. Photoelectron spectrometer for attosecond spectroscopy of liquids and gases

    Energy Technology Data Exchange (ETDEWEB)

    Jordan, I.; Huppert, M.; Wörner, H. J., E-mail: hwoerner@ethz.ch [Laboratory of Physical Chemistry, ETH Zurich, Vladimir-Prelog-Weg 2, 8093 Zurich (Switzerland); Brown, M. A. [Laboratory for Surface Science and Technology, Department of Materials, ETH Zurich, Vladimir-Prelog-Weg 5, 8093 Zurich (Switzerland); Bokhoven, J. A. van [Institute for Chemical and Bioengineering, ETH Zurich, Vladimir-Prelog-Weg 1, 8093 Zurich (Switzerland); Laboratory for Catalysis and Sustainable Chemistry, Paul Scherrer Institute, 5232 Villigen (Switzerland)

    2015-12-15

    A new apparatus for attosecond time-resolved photoelectron spectroscopy of liquids and gases is described. It combines a liquid microjet source with a magnetic-bottle photoelectron spectrometer and an actively stabilized attosecond beamline. The photoelectron spectrometer permits venting and pumping of the interaction chamber without affecting the low pressure in the flight tube. This pressure separation has been realized through a sliding skimmer plate, which effectively seals the flight tube in its closed position and functions as a differential pumping stage in its open position. A high-harmonic photon spectrometer, attached to the photoelectron spectrometer, exit port is used to acquire photon spectra for calibration purposes. Attosecond pulse trains have been used to record photoelectron spectra of noble gases, water in the gas and liquid states as well as solvated species. RABBIT scans demonstrate the attosecond resolution of this setup.

  16. Photoelectron spectrometer for attosecond spectroscopy of liquids and gases

    International Nuclear Information System (INIS)

    Jordan, I.; Huppert, M.; Wörner, H. J.; Brown, M. A.; Bokhoven, J. A. van

    2015-01-01

    A new apparatus for attosecond time-resolved photoelectron spectroscopy of liquids and gases is described. It combines a liquid microjet source with a magnetic-bottle photoelectron spectrometer and an actively stabilized attosecond beamline. The photoelectron spectrometer permits venting and pumping of the interaction chamber without affecting the low pressure in the flight tube. This pressure separation has been realized through a sliding skimmer plate, which effectively seals the flight tube in its closed position and functions as a differential pumping stage in its open position. A high-harmonic photon spectrometer, attached to the photoelectron spectrometer, exit port is used to acquire photon spectra for calibration purposes. Attosecond pulse trains have been used to record photoelectron spectra of noble gases, water in the gas and liquid states as well as solvated species. RABBIT scans demonstrate the attosecond resolution of this setup

  17. Photoelectron spectrometer for attosecond spectroscopy of liquids and gases

    Science.gov (United States)

    Jordan, I.; Huppert, M.; Brown, M. A.; van Bokhoven, J. A.; Wörner, H. J.

    2015-12-01

    A new apparatus for attosecond time-resolved photoelectron spectroscopy of liquids and gases is described. It combines a liquid microjet source with a magnetic-bottle photoelectron spectrometer and an actively stabilized attosecond beamline. The photoelectron spectrometer permits venting and pumping of the interaction chamber without affecting the low pressure in the flight tube. This pressure separation has been realized through a sliding skimmer plate, which effectively seals the flight tube in its closed position and functions as a differential pumping stage in its open position. A high-harmonic photon spectrometer, attached to the photoelectron spectrometer, exit port is used to acquire photon spectra for calibration purposes. Attosecond pulse trains have been used to record photoelectron spectra of noble gases, water in the gas and liquid states as well as solvated species. RABBIT scans demonstrate the attosecond resolution of this setup.

  18. Laboratory evaluation of hot metal de siliconizing process in ladle; Avaliacao laboratorial do processo de dessiliciacao do gusa na panela

    Energy Technology Data Exchange (ETDEWEB)

    Passos, Sergio R.M.; Furtado, Henrique S.; Bentes, Miguel A.G.; Almeida, Pedro S. de [Companhia Siderurgica Nacional, Volta Redonda, RJ (Brazil). Centro de Pesquisas

    1996-12-31

    The attractiveness of hot metal de siliconizing in ladle, relative to the process in blast furnace runner, is the previous knowledge of silicon content of hot metal, without the constraints of slag removing by skimmer met in torpedo car, and the better efficiency in low range silicon content, making easier the process controllability. Meanwhile, the main question about this technology is the extent of the resulfurization of hot metal that may occur due to process be performed after the desulfurization. This work simulates de de siliconizing process in ladle by experiments in induction furnace to compare the efficiencies of various de siliconizing agents available at CSN iron and steel making plant, and to evaluate the resulfurization intensity able to occur during the process, as well as, unexpected increasing of refractory wear. (author) 4 refs., 8 figs., 6 tabs.

  19. North Slope mobile technology and its application to spill response

    International Nuclear Information System (INIS)

    Mabile, N.J.; Helinski, R.

    1992-01-01

    At ARCO Alaska's Prudhoe Bay operation, improved preparedness for oil spill response has been achieved by applying mobile technology according to an innovative concept. To ensure safe and efficient deployment of resources during a spill response, a rapid deployment equipment delivery system was developed. This multi-functional, modularized system was based on a previously developed chemical delivery system consisting of a primary transport truck equipped with a Dempsey Dumpster Dinosaur skid. This same modularized concept was used for spill response with the substitution of function-specific spill response vans in place of chemical transport tanks. Within this concept, skid-mounted mission-specific vans are rapidly deployed to multiple sites in a fire brigade type of response. Skid-mounted units include land and water containment, recovery, boom deployment, command center, generator skid, restroom facility, and skimmer units. 4 figs

  20. Ion sampling and transport in Inductively Coupled Plasma Mass Spectrometry

    Science.gov (United States)

    Farnsworth, Paul B.; Spencer, Ross L.

    2017-08-01

    Quantitative accuracy and high sensitivity in inductively coupled plasma mass spectrometry (ICP-MS) depend on consistent and efficient extraction and transport of analyte ions from an inductively coupled plasma to a mass analyzer, where they are sorted and detected. In this review we examine the fundamental physical processes that control ion sampling and transport in ICP-MS and compare the results of theory and computerized models with experimental efforts to characterize the flow of ions through plasma mass spectrometers' vacuum interfaces. We trace the flow of ions from their generation in the plasma, into the sampling cone, through the supersonic expansion in the first vacuum stage, through the skimmer, and into the ion optics that deliver the ions to the mass analyzer. At each stage we consider idealized behavior and departures from ideal behavior that affect the performance of ICP-MS as an analytical tool.

  1. Characterization of primaquine imidazolidin-4-ones with antimalarial activity by electrospray ionization-ion trap mass spectrometry

    Science.gov (United States)

    Vale, Nuno; Moreira, Rui; Gomes, Paula

    2008-02-01

    The extensive characterization by electrospray ionization-ion trap mass spectrometry (ESI-MSn) of 20 imidazolidin-4-ones derived from the antimalarial primaquine was well obtained. These compounds are being under investigation as potential antimalarials, as they have been previously found to be active against rodent P. berghei malaria and to be highly stable under physiological conditions. Experiments by collision-induced dissociation (CID) in the nozzle-skimmer region or by tandem-MS have shown the title compounds to be remarkably stable. Mechanisms are proposed to explain the major fragmentations observed in ESI-MSn experiments. Overall, this work represents an unprecedented contribution to a deeper insight into imidazolidin-4-one antimalarials based on a classic 8-aminoquinolinic scaffold. Data herein reported and discussed may be an useful guide for future studies on therapeutically relevant molecules possessing either the 8-aminoquinoline or the imidazolidin-4-one motifs.

  2. Measurement of the density profile of pure and seeded molecular beams by femtosecond ion imaging

    Energy Technology Data Exchange (ETDEWEB)

    Meng, Congsen [LaserLaB Amsterdam, VU University Amsterdam, de Boelelaan 1083, 1081 HV Amsterdam (Netherlands); Department of Physics, National University of Defense Technology, Changsha 410073 (China); Janssen, Maurice H. M. [LaserLaB Amsterdam, VU University Amsterdam, de Boelelaan 1083, 1081 HV Amsterdam (Netherlands)

    2015-02-15

    Here, we report on femtosecond ion imaging experiments to measure the density profile of a pulsed supersonic molecular beam. Ion images are measured for both a molecular beam and bulk gas under identical experimental conditions via femtosecond multiphoton ionization of Xe atoms. We report the density profile of the molecular beam, and the measured absolute density is compared with theoretical calculations of the centre line beam density. Subsequently, we discuss reasons accounting for the differences between measurements and calculations and propose that strong skimmer interference is the most probable cause for the differences. Furthermore, we report on experiments measuring the centre line density of seeded supersonic beams. The femtosecond ion images show that seeding the heavy Xe atom at low relative seed fractions (1%-10%) in a light carrier gas like Ne results in strong relative enhancements of up to two orders of magnitude.

  3. Water management

    International Nuclear Information System (INIS)

    Anon.

    1996-01-01

    Manitoba Hydro's efforts to maximize production efficiency while meeting safety and environmental concerns regarding water management were discussed. The four-step dam safety program was outlined, consisting of inspection, repairs and improvements, flooding studies, and emergency preparedness plans. An oil spill which occurred in 1995 on the Nelson River after a transformer at the Kettle Generating Station failed, was described. A boom was used to contain the oil, and a skimmer unit was used to remove oil and soot from the surface of the water. Manitoba Hydro is also conducting studies to find ways to protect the generating stations from zebra mussels, and precautions are being taken to prevent old lead-based paint from reaching the Winnipeg River. It was noted that the drought which hit northern Manitoba during the spring and summer of 1995 reduced the water supplies to the lowest levels ever recorded at the Churchill River Diversion. 2 figs

  4. Water management

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-31

    Manitoba Hydro`s efforts to maximize production efficiency while meeting safety and environmental concerns regarding water management were discussed. The four-step dam safety program was outlined, consisting of inspection, repairs and improvements, flooding studies, and emergency preparedness plans. An oil spill which occurred in 1995 on the Nelson River after a transformer at the Kettle Generating Station failed, was described. A boom was used to contain the oil, and a skimmer unit was used to remove oil and soot from the surface of the water. Manitoba Hydro is also conducting studies to find ways to protect the generating stations from zebra mussels, and precautions are being taken to prevent old lead-based paint from reaching the Winnipeg River. It was noted that the drought which hit northern Manitoba during the spring and summer of 1995 reduced the water supplies to the lowest levels ever recorded at the Churchill River Diversion. 2 figs.

  5. FY 2000 report on the results of the regional consortium R and D project - Regional consortium R and D field. First year report. Development of an on-line/real-time dioxin measuring system; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium kenkyu kaihatsu bun'ya. Dioxin no on line real time keisoku sochi no kaihatsu (dai 1 nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With the supersonic molecular jet resonance multiple photon ionization mass analysis method (SSJ method) as basement technology, the development was proceeded with of a portable dioxin spectrometer to measure dioxins emitted from incinerator on line and at real time and to control/improve the state of combustion. Studies were made in the following three fields: 1) development of pico second wavelength variable color laser; 2) development of a flight hour type mass spectrometer; 3) development of the pretreatment technology suitable for analysis of dioxins, precursors, etc. by supersonic molecular jet spectroscopy. In 1), the prototype was fabricated to assess the performance, and it was confirmed that the prototype has the targeted characteristics. In 2), as to the coaxial ionization and ring double skimmer electrode system, the convergence and mass resolution of ion were measured, and a possibility of the commercialization was obtained. In 3), it was confirmed that there is a possibility in rapid pretreatment by alumina fiber filter. (NEDO)

  6. Pool water cleaning facility

    Energy Technology Data Exchange (ETDEWEB)

    Yoshikawa, Kazuhiro; Kinoshita, Shoichiro [Hitachi Ltd., Tokyo (Japan); Asano, Takashi

    1998-05-29

    Only one system comprising a suppression poor water cleaning system (SPCU) and a filtration desalting tower (F/D) is connected for a plurality of nuclear power plants. Pipelines/valves for connecting the one system of the SPCU pump, the F/D and the plurality of nuclear power plants are disposed, and the system is used in common with the plurality of nuclear power plants. Pipelines/valves for connecting a pipeline for passing SP water to the commonly used SPCU pump and a skimmer surge tank are disposed, and fuel pool water is cooled and cleaned by the commonly used SPCU pump and the commonly used F/D. The number of SPCU pumps and the F/D facilities can be reduced, and a fuel pool water cooling operation mode and a fuel pool water cleaning operation mode which were conducted by an FPC pump so far are conducted by the SPCU pump. (N.H.)

  7. Maximum tech, minimum time. Response and cleanup of the Fidalgo Bay oil spill

    International Nuclear Information System (INIS)

    Pintler, L.R.

    1991-01-01

    A booster pump failure on a pipeline at Texaco's Anacortes refinery spilled more than 17,000 gallons of oil into Fidalgo Bay. A description is given of the spill control measures taken under Texaco's Spill Prevention and Control Countermeasures and facility contingency plans. The spill was addressed quickly, and containment booms were used to cordon off the spill. Vacuum trucks, rope mop machines and disk skimmers were used to collect the thickest concentrations of oil, and the oil and water collected was separated at the refinery's wastewater treatment centre. Nonwoven polypropylene sorbent pads, sweeps, booms and oil snares were used to clean up thinner concentrations of oil. Essential steps for a smooth spill response include the following: a comprehensive spill prevention and control countermeasures plan, training and regular drills and testing; immediate notification of appropriate regulatory agencies and company emergency response personnel; and the use of professional oil spill management contractors to assist in spill cleanup. 2 figs

  8. Graphene stirrer with designed movements: Targeting on environmental remediation and supercapacitor applications

    Directory of Open Access Journals (Sweden)

    Yang Huang

    2018-01-01

    Full Text Available Beyond the traditional focus on improvements in mechanical, electronic and absorption properties, controllability, actuation, and dynamic response of monoliths have received increasing attentions for practical applications. However, most of them could only realize simple response to constant conditions (e.g. a stationary magnetic field while carrying out humdrum motions. By controlling distribution of metal organic framework obtained carbon-enriched Fe3O4 nanoparticles in self-assembly reduced graphene oxide (RGO monoliths, we could achieve two distinctive RGO–Fe3O4 stirrers that could dynamically respond to the rapidly changing magnetic field while executing designed movements precisely: rotating with lying down posture or standing straight posture. These stirrers can not only be applied in environmental remediation (e.g. suction skimmer, but also be recycled as electrode active materials for supercapacitors after fulfilling their destiny, realizing transformation of trash to treasure, which will inspire other dynamically responsive monoliths for various applications.

  9. Laser Desorption of Tryptophan from Tryptophan-HCl Salt on a Graphite Substrate

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Hae Jun; Kim, Jeong Jin; Kang, Hyuk [Ajou University, Suwon (Korea, Republic of)

    2016-03-15

    Laser spectroscopy of biological molecules in the gas phase has been pioneered by Levy and coworkers when they first produced a supersonic molecular beam of tryptophan (Trp) and obtained its electronic spectrum. They were able to obtain enough vapor pressure needed for spectroscopy by heating a powder sample of Trp, although a special thermal spray was used to minimize fragmentation during heating. Many amine compounds, including biomolecules like amino acids and peptides, are usually available only as HCl salt form in order to prevent oxidation in air. Chemical processing is required to recover a neutral amine compound from its salt, thus limiting the applicability of laser-desorption spectroscopy of biomolecules. The experimental setup is a standard molecular beam machine composed of a pulsed valve with a laser-desorption module in a vacuum chamber, a second buffer chamber, a skimmer that separates the first and the second chambers, and a third vacuum chamber that is a time-of-flight mass spectrometer (TOF MS)

  10. Fundamental and methodological investigations for the improvement of elemental analysis by inductively coupled plasma mass soectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Ebert, Christopher Hysjulien [Ames Lab., Ames, IA (United States)

    2012-01-01

    This dissertation describes a variety of studies meant to improve the analytical performance of inductively coupled plasma mass spectrometry (ICP-MS) and laser ablation (LA) ICP-MS. The emission behavior of individual droplets and LA generated particles in an ICP is studied using a high-speed, high frame rate digital camera. Phenomena are observed during the ablation of silicate glass that would cause elemental fractionation during analysis by ICP-MS. Preliminary work for ICP torch developments specifically tailored for the improvement of LA sample introduction are presented. An abnormal scarcity of metal-argon polyatomic ions (MAr{sup +}) is observed during ICP-MS analysis. Evidence shows that MAr{sup +} ions are dissociated by collisions with background gas in a shockwave near the tip of the skimmer cone. Method development towards the improvement of LA-ICP-MS for environmental monitoring is described. A method is developed to trap small particles in a collodion matrix and analyze each particle individually by LA-ICP-MS.

  11. Effectiveness of the stormwater quality devices to improve water quality at Putrajaya

    International Nuclear Information System (INIS)

    Sidek, L M; Basri, H; Puad, A H Mohd; Noh, M N Md; Ainan, A

    2013-01-01

    Development of Putrajaya has changed the character of the natural landform by covering the land with impervious surfaces. Houses, office buildings, commercial place and shopping centres have provided places to live and work. The route between buildings is facilitated and encouraged by a complex network of roads and car parks. However, this change from natural landforms and vegetative cover to impervious surfaces has major effect on stormwater which are water quality (non-point source pollution). This paper describes the effectiveness of the stormwater quality devices to improve water quality at selected Putrajaya for demonstration in order to evaluate low cost storm inlet type devices in the Putrajaya Catchment. Five stormwater quality devices were installed and monitored during the study. The devices include Ultra Drain Guard Recycle model, Ultra Curb Guard Plus, Ultra Grate Guard, Absorbent Tarp and Ultra Passive Skimmer. This paper will provide information on the benefits and costs of these devices, including operations and maintenance requirements. Applicability of these devices in gas stations, small convenience stores, residential and small parking lots in the catchment are possible due to their low cost.

  12. Alyeska/SERVS technological innovations for oil spill response

    International Nuclear Information System (INIS)

    Hillman, S.O.

    1996-01-01

    An overview of technological innovations in spill response by Alyeska Pipeline Service Company/SERVS (ship escort response vessel system), was presented. The company has developed a number of spill response techniques which have needed new strategies and modified equipment for fulfillment of the Prince William Sound Tanker Oil Discharge Prevention and Contingency Plan. One of the strategies was the training of personnel to be ready to deploy massive quantities of equipment on short notice to potential spill sites over an 11,000 square mile water body with more than 3,200 miles of wilderness shoreline. Specific response equipment and decision-making tools have been developed in direct support of large scale programs. Along with oil slick tracking buoys and mini barges, SERVS has developed high capacity skimmers with recovery capacities approaching 2,000 to 3,000 barrels of liquid per hour and strategy boom-towing vessels which divert oil into a long U shaped containment boom. SERVS fishing vessel program, hatchery protection and remote response center equipment program, and wildlife treatment facilities were also described. 10 refs., 13 figs

  13. STATUS REPORT ON DEVELOPMENT OF A HIGH-SPEED HIGH-INTENSITY MOLECULAR BEAM

    Energy Technology Data Exchange (ETDEWEB)

    Knuth, Eldon L.

    1963-07-15

    Status of a high-speed high-intensity molecular beam under development is described. Bases for designs of the several components are presented. Using an arc-heated source and a hypersonic jet, molecular energies exceeding 1 ev and beam intensities of the order of 10/sup 16/ molecules/ cm/sup 2/ sec are anticipated. A two-disk beam chopper and speed selector provides a means for analyzing the speed distribution in the generated beam, for chopping the beam into bursts of nearly monoenergetic molecules suitable for scattering studies using the time-of-flight technique, and for modulating the beam in order to facilitate detection. A through-flow ionization detector possesses the versatility required for scattering studies using the time-of-flight technique. A sorption pump and a turbo pump serve as central components of alternative pumping systems for the collimating chamber. Using the arc-heated source, the converging nozzle, the conduction-radiation-cooled skimmer, the turbo pump (turning at 3400 rpm), the chopperselector (acting only as a chopper), and the detector, an arc-heated beam is generated and detected. (auth)

  14. Optimal beam sources for Stark decelerators in collision experiments: a tutorial review

    International Nuclear Information System (INIS)

    Vogels, Sjoerd N.; Gao, Zhi; Meerakker, Sebastiaan Y.T. van de

    2015-01-01

    With the Stark deceleration technique, packets of molecules with a tunable velocity, a narrow velocity spread, and a high state purity can be produced. These tamed molecular beams find applications in high resolution spectroscopy, cold molecule trapping, and controlled scattering experiments. The quality and purity of the packets of molecules emerging from the decelerator critically depend on the specifications of the decelerator, but also on the characteristics of the molecular beam pulse with which the decelerator is loaded. We consider three frequently used molecular beam sources, and discuss their suitability for molecular beam deceleration experiments, in particular with the application in crossed beam scattering in mind. The performance of two valves in particular, the Nijmegen Pulsed Valve and the Jordan Valve, is illustrated by decelerating ND 3 molecules in a 2.6 meter-long Stark decelerator. We describe a protocol to characterize the valve, and to optimally load the pulse of molecules into the decelerator. We characterize the valves regarding opening time duration, optimal valve-to-skimmer distance, mean velocity, velocity spread, state purity, and relative intensity. (orig.)

  15. Campargue-type supersonic beam sources : absolute intensities, skimmer transmission and scaling laws for mono-atomic gases He, Ne and Ar

    NARCIS (Netherlands)

    Beijerinck, H.C.W.; van Gerwen, R.J.F.; Kerstel, E.R.T.; Martens, J.F.M.; van Vliembergen, E.J.W.; Smits, M.R.T.; Kaashoek, G.H.

    1985-01-01

    The process of beam formation in a supersonic expansion into a high pressure (10-2 -1 Torr) expansion chamber, a so-called Campargue-type beam source, has been investigated, using the theoretical frame work of an ideal undisturbed expansion as a reference. Absolute values of the centre-line

  16. AMOP (Arctic Marine Oil Spill Program) studies reviewed

    Energy Technology Data Exchange (ETDEWEB)

    1978-06-05

    A discussion of the Arctic Marine Oil Spill Program organized in 1976 by the Canadian Federal Government includes: an Arctic Atlas compiled by Fenco Consultants Ltd. to give background information necessary for developing marine oil spill countermeasures for the Arctic north of 60/sup 0/ including the west Greenland coast and the Labrador shelf (geology, meteorology and oceanography, ice conditions, biology, and social factors); program in emergency transport of spill-combatting equipment; and the factors which influence the choice of conveyance, i.e., accessibility of the site, urgency for response, and quantity of material required; laboratory studies involving the release of oil under artificial sea ice in simulated ice formation and decay purposes to determine the interaction of crude oil and first-year sea ice; inability of companies and government to control a major spill in the Labrador Sea because of poor and inadequate transport facilities, communications, and navigational aids, severe environmental conditions, and logistics problems; and studies on the effects of oil-well blowouts in deep water, including formation of oil and gas hydrates, design of oil skimmers, the use of hovercraft, and specifications for an airborne multisensor system for oil detection in ice-infested waters.

  17. Performance of the cluster-jet target for PANDA

    Energy Technology Data Exchange (ETDEWEB)

    Hergemoeller, Ann-Katrin; Bonaventura, Daniel; Grieser, Silke; Hetz, Benjamin; Koehler, Esperanza; Khoukaz, Alfons [Institut fuer Kernphysik, Westfaelische Wilhelms-Universitaet Muenster, 48149 Muenster (Germany)

    2016-07-01

    The success of storage ring experiments strongly depends on the choice of the target. For this purpose, a very appropriate internal target for such an experiment is a cluster-jet target, which will be the first operated target at the PANDA experiment at FAIR. In this kind of target the cluster beam itself is formed due to the expansion of pre-cooled gases within a Laval nozzle and is prepared afterwards via two orifices, the skimmer and the collimator. The target prototype, operating successfully for years at the University of Muenster, provides routinely target thicknesses of more than 2 x 10{sup 15} (atoms)/(cm{sup 2}) in a distance of 2.1 m behind the nozzle. Based on the results of the performance of the cluster target prototype the final cluster-jet target source was designed and set into operation in Muenster as well. Besides the monitoring of the cluster beam itself and the thickness with two different monitoring systems at this target, investigations on the cluster mass via Mie scattering will be performed. In this presentation an overview of the cluster target design, its performance and the Mie scattering method are presented and discussed.

  18. Options for cleaning up subsurface contamination at Alberta sour gas plants

    International Nuclear Information System (INIS)

    Hardisty, P.; Dabrowski, T.L.

    1992-01-01

    At the conclusion of two major phases of a study on subsurface treatment technologies for Alberta sour gas plants, a candidate site was selected for a remediation technologies demonstration project. The plant has an extensive groundwater monitoring network in place, monitoring records for a period exceeding 10 years, ten recovery wells with aquifer test data and four reinjection wells. Hydrogeological exploration determined the presence and delineated a plume of free phase natural gas condensate. Aquifer remediation efforts at the site began in 1990 with the installation of recovery wells. Recovered groundwater was treated using a pilot scale air stripping system with pretreatment for iron, manganese and hardness. Dual pump system, water depression and free product skimmers were installed in the wells and tested. The nature and extent of contamination, study methodology, technology-dependent criteria, assessment of technology, and conceptual design are discussed for the three demonstration projects selected, which are enhanced soil vapour extraction with off-gas treatment, pump-and-treat with soil vapour extraction, biological treatment and air sparging, and treatment of dissolved process chemicals by advanced oxidation. 5 refs., 1 fig., 1 tab

  19. Mass spectrometric measurements of the freestream composition in the T4 free-piston shock-tunnel

    Science.gov (United States)

    Boyce, R. R.; Takahashi, M.; Stalker, R. J.

    2005-12-01

    The freestream composition is an important parameter in ground-based aerodynamic testing, and direct measurement of it is very important. This paper reports extensive composition measurements in the freestream of the T4 free-piston shock-tunnel, employing a recently improved time-of-flight mass spectrometer. A wide range of nozzle reservoir conditions were used. The results show good agreement between measured and theoretical values for nitric oxide over the entire enthalpy range reported (2.5 13 MJ/kg). This provides confidence that the chemistry model is correctly predicting sudden freezing of NO in the nozzle expansion. On the other hand, no monatomic species have been measured other than those produced by dissociative ionisation within the mass spectrometer, even at flow conditions where significant freestream dissociation is expected. Furthermore, excess diatomic oxygen is detected at high enthalpies. These observations are consistent with the possibility that oxygen recombination is not correctly predicted in the nozzle expansion, with sudden freezing occurring significantly later than predicted. However, the observations are also consistent with possible catalytic recombination in the skimmer system. The possibility for producing an empirical correlation between the freestream composition and the reservoir entropy has also been observed.

  20. Isolated Bacterial Spores at High-velocity Survive Surface Impacts in Vacuum

    Science.gov (United States)

    Austin, Daniel; Barney, Brandon

    We present experiments in which bacterial spores were found to survive being accelerated in vacuum to velocities in the range 30-120 m/s and impacted on a dense target. In these experiments, spores of Bacillus subtilis spores were charged using electrospray at atmospheric pressure, dried, and then introduced into high vacuum. Through choice of skimmers and beam tubes, different velocity ranges were achieved. An image-charge detector observed the charged spores, providing total charge and velocity. The spores then impacted a glass target within a collection vessel. After the experiment, the collection vessel contents were extracted and cultured. Several positive and negative controls were used, including the use of antibiotic-resistant spores and antibiotic-containing (rifampicin) agar for culturing. These impact velocities are of particular interest for possible transport of bacterial spores from Mars to Phobos, and may have implications for planetary protection in a Phobos sample return mission. In addition, bacteria may reach similar velocities during a spacecraft crash (e.g., within components, or from spacecraft to surface materials during impact, etc.), raising concerns about forward contamination. The velocities of interest to transport of life between planets (panspermia) are somewhat higher, but these results complement shock-based experiments and contribute to the general discussion of impact survivability of organisms.

  1. Influence of throttling of the heavy fraction on the uranium isotope separation in the separation nozzle

    International Nuclear Information System (INIS)

    Bley, P.; Ehrfeld, W.; Heiden, U.

    1978-04-01

    In a separation nozzle cascade for enrichment of U-235 the cut of the separation elements is adjusted by throttling the heavy fraction. This control process influences directly the flow properties in the nozzle and may noticeably change its separation characteristics. This paper deals with an experimental investigation of the throttling effect on the separation and control characteristics of the separation nozzle operated with a H 2 /UF 6 mixture. In consideration of the extremely small characteristic dimensions of commercial separation nozzle elements the influence of manufacturing tolerances on the characteristics of the throttled nozzle was analysed in detail. It appears, that the elementary effect of isotope separation increases by throttling of the heavy fraction up to 5% without changing the optimum operating conditions. This increase of the elementary effect is not only obtained for separation nozzles with zero tolerances but also for separation nozzles having finite tolerances of the skimmer position. Tolerances of the nozzle width, however, become increasingly detrimental, when the heavy fraction is throttled. Regarding the control characteristics of the separation nozzle it was found out, that the UF 6 -cut of the throttled nozzle reacts more sensitively to alterations of the operating pressures and less sensitively to alterations of the UF 6 -concentration of the process gas mixture. (orig.) [de

  2. Technology needs for the later phases of an oil spill. Volume 1

    International Nuclear Information System (INIS)

    Goodman, R.

    2007-01-01

    The phases of an oil spill response can be classified as initial response, project phase, end phase and the monitoring phase. The initial on-water phase of the response or shoreline cleanup includes the development of contingency planning, stockpiling of equipment and research into response equipment for removing oil on water. Lack of planning for a response can lead to an initial response that has less than satisfactory results. An initial assessment of the oil spill response begins at the moment the spill occurs and continues for days, depending on the quality of the initial response. This phase includes the use of booms, skimmers, dispersants and in-situ burning. It was emphasized that oil spill research should focus on gathering scientific information needed to make decisions during the project phase and beyond. Typically, this will involve the study of long-term impacts and should be undertaken in a research environment in order to apply new data to any spill scenario. This paper highlighted knowledge needs to support decisions in the cleanup phase. The Exxon Valdez incident provided information on the long-term impacts of a variety of cleanup techniques. This paper also addressed damage assessment and restoration issues along with the decision to terminate a response. Once a response has been terminated, long-term monitoring of the ecosystem begins in order to identify the spill impact. 9 refs., 6 figs

  3. Electron beam fluorescence spectrometry of internal state populations in nozzle beams of nitrogen and nitrogen/rare gas mixtures

    International Nuclear Information System (INIS)

    Faubel, M.; Weiner, E.R.

    1981-01-01

    Rotational level populations of N 2 were measured downstream from the skimmer in beams of pure N 2 and in mixtures of N 2 with He, Ne, and Ar expanded from room temperature nozzles. The range of p 0 D was from 5 to 50 Torr cm. The formation of dimers and higher condensates of beam species was monitored during the runs. The effect of condensation energy release on rotational populations and parallel temperatures was readily observed. Two different methods for evaluating the rotational population distributions were compared. One method is based on a dipole-excitation model and the other on an excitation matrix obtained empirically. Neither method proved clearly superior. Both methods indicated nonequilibrium rotational populations for all of our room temperature nozzle expansion conditions. Much of the nonequilibrium character appears to be due to the behavior of the K = 2 and K = 4 levels, which may be accounted for in terms of the rotational energy level spacing. In particular, the overpopulation of the K = 4 level is explained by a near-resonant transfer of rotational energy between molecules in the K = 6 and K = 0 states, to give two molecules in the K = 4 state. Rotational and vibrational temperatures were determined for pure N 2 beams from nozzles heated up to 1700 0 K. The heated nozzle experiments indicated a 40% increase in the rotational collision number between 300 and 1700 0 K

  4. Development of a cluster-jet target for PANDA

    International Nuclear Information System (INIS)

    Gruber, A.; Marton, J.; Widmann, E.; Zmeskal, J.; Orth, H.; Luehning, J.

    2008-01-01

    Full text: The Stefan Meyer Institut (SMI) is part of the international PANDA collaboration. The universal detector will be constructed at the future high-energy antiproton storage ring HESR at FAIR (Facility for Antiproton and Ion Research, GSI/Darmstadt). PANDA will use antiproton beams (1.5 to 15 GeV/c) for hadron physics in the charmonium region. The physics program of PANDA will encompass charmonium spectroscopy below and above open charm threshold, search for exotics (glueballs, hybrids), lambda and double-lambda hypernuclei studies and the investigation of in-medium modifications of charmed mesons - an experimentally unexplored field. SMI contributes to major parts of the PANDA detector like the hydrogen cluster-jet target and the vacuum system of the antiproton - target interaction zone. In order to reach the desired target density, an optimization of the cold head, the nozzle and the skimmer arrangement is essential. A density-profile monitor for the cluster-jet was designed and built at SMI. Several nozzle types will be studied using different gases, temperatures and inlet pressures. Additionally we, together with the cluster-jet target group at GSI, are carrying out R and D for improving the jet-density. The Genova/Fermilab cluster-jet target used for these measurements has been in use at Fermilab for the experiments E760 and E835 and has been transferred to GSI for this purpose. The setup of the density-profile monitor at SMI and several measurements at GSI will be presented. (author)

  5. Development of a cluster-jet target for PANDA

    International Nuclear Information System (INIS)

    Gruber, A.; Marton, J.; Widmann, E.; Zmeskal, J.; PANDA Cluster Jet Target Group

    2006-01-01

    Full text: The Stefan Meyer Institute (SMI) is part of the international PANDA collaboration. The universal detector will be constructed for the future high-energy antiproton storage ring HESR at FAIR (Facility for Antiproton and Ion Research, GSI/Darmstadt). PANDA will use antiproton beams (1.5 to 15 GeV/c) for hadron physics in the charmonium region. The physics program of PANDA will comprehend charmonium spectroscopy below and above open charm threshold, search for exotics (glueballs, hybrids), lambda and double-lambda hypernuclei studies and the investigation of in-medium modifications of charmed mesons - an experimentally unexplored field. SMI contributes to major parts of the PANDA detector like the hydrogen cluster-jet target and the antiproton - cluster jet interaction zone: in order to reach the desired target density, an optimization of the nozzle and the skimmer arrangement is essential. A density-profile monitor for the cluster-jet was designed and built at SMI. Several nozzle types have been studied using different gases, temperatures and inlet pressures. To ensure low background the residual gas load in the interaction zone has to be minimized. The installation of NEG (non-evaporative-getter) coated beam pipes is planned. A prototype of the interaction zone has been set up at SMI. The pumping capacity of NEG and the reactivation cycles were tested. The status of the development of the cluster-jet target and studies of the interaction region will be presented (author)

  6. Temperature-dependent release of volatile organic compounds of eucalypts by direct analysis in real time (DART) mass spectrometry.

    Science.gov (United States)

    Maleknia, Simin D; Vail, Teresa M; Cody, Robert B; Sparkman, David O; Bell, Tina L; Adams, Mark A

    2009-08-01

    A method is described for the rapid identification of biogenic, volatile organic compounds (VOCs) emitted by plants, including the analysis of the temperature dependence of those emissions. Direct analysis in real time (DART) enabled ionization of VOCs from stem and leaf of several eucalyptus species including E. cinerea, E. citriodora, E. nicholii and E. sideroxylon. Plant tissues were placed directly in the gap between the DART ionization source skimmer and the capillary inlet of the time-of-flight (TOF) mass spectrometer. Temperature-dependent emission of VOCs was achieved by adjusting the temperature of the helium gas into the DART ionization source at 50, 100, 200 and 300 degrees C, which enabled direct evaporation of compounds, up to the onset of pyrolysis of plant fibres (i.e. cellulose and lignin). Accurate mass measurements facilitated by TOF mass spectrometry provided elemental compositions for the VOCs. A wide range of compounds was detected from simple organic compounds (i.e. methanol and acetone) to a series of monoterpenes (i.e. pinene, camphene, cymene, eucalyptol) common to many plant species, as well as several less abundant sesquiterpenes and flavonoids (i.e. naringenin, spathulenol, eucalyptin) with antioxidant and antimicrobial properties. The leaf and stem tissues for all four eucalypt species showed similar compounds. The relative abundances of methanol and ethanol were greater in stem wood than in leaf tissue suggesting that DART could be used to investigate the tissue-specific transport and emissions of VOCs. Copyright (c) 2009 John Wiley & Sons, Ltd.

  7. Feasibility of treating emulsified oily and salty wastewaters through coagulation and bio-regenerated GAC filtration.

    Science.gov (United States)

    Mancini, Giuseppe; Panzica, Michele; Fino, Debora; Cappello, Simone; Yakimov, Michail M; Luciano, Antonella

    2017-12-01

    In the present study, chemical oxygen demand (COD) removal by coagulation and packed-columns of both fresh and bioregenerated granular activated carbon (GAC) is reported as a feasible treatment for saline and oily wastewaters (slops) generated from marine oil tankers cleaning. The use of Ferric chloride (FeCl 3 ), Aluminium sulphate (Al 2 (SO 4 ) 3 ) and Polyaluminum chloride (Al 2 (OH 3 )Cl 3 ) was evaluated in the pre-treatment by coagulation of a real slop, after a de-oiling phase in a tank skimmer Comparison of coagulation process indicated that Polyaluminum chloride and Aluminium sulphate operate equally well (20-30% of COD removal) when applied at their optimal dose (40 and 90 mg/l respectively) but the latter should be preferred in order to significantly control the sludge production. The results from the column filtration tests indicated the feasibility of using the selected GAC (Filtrasorb 400 -Calgon Carbon Corporation) to achieve the respect of the discharge limits in the slops treatment with a carbon usage rate in the range 0.1-0.3 kg/m 3 of treated effluent. Moreover, biological regeneration through Alcalinovorax borkumensis SK2 was proved to be a cost-effective procedure since the reuse of spent GAC through such regeneration process for further treatment could still achieve approximately 90% of the initial sorption capacity, reducing then costs for the use of new sorbents and also the need for waste disposal. Copyright © 2016 Elsevier Ltd. All rights reserved.

  8. Basic features of boron isotope separation by SILARC method in the two-step iterative static model

    Science.gov (United States)

    Lyakhov, K. A.; Lee, H. J.

    2013-05-01

    In this paper we develop a new static model for boron isotope separation by the laser assisted retardation of condensation method (SILARC) on the basis of model proposed by Jeff Eerkens. Our model is thought to be adequate to so-called two-step iterative scheme for isotope separation. This rather simple model helps to understand combined action on boron separation by SILARC method of all important parameters and relations between them. These parameters include carrier gas, molar fraction of BCl3 molecules in carrier gas, laser pulse intensity, gas pulse duration, gas pressure and temperature in reservoir and irradiation cells, optimal irradiation cell and skimmer chamber volumes, and optimal nozzle throughput. A method for finding optimal values of these parameters based on some objective function global minimum search was suggested. It turns out that minimum of this objective function is directly related to the minimum of total energy consumed, and total setup volume. Relations between nozzle throat area, IC volume, laser intensity, number of nozzles, number of vacuum pumps, and required isotope production rate were derived. Two types of industrial scale irradiation cells are compared. The first one has one large throughput slit nozzle, while the second one has numerous small nozzles arranged in parallel arrays for better overlap with laser beam. It is shown that the last one outperforms the former one significantly. It is argued that NO2 is the best carrier gas for boron isotope separation from the point of view of energy efficiency and Ar from the point of view of setup compactness.

  9. In situ bioremediation strategies for oiled shoreline environments

    International Nuclear Information System (INIS)

    Lee, K.; Mora, S. de

    1999-01-01

    Despite advances in preventative measures, recent events have demonstrated that accidental oil spills at sea will still occur. While physical (e.g. booms and skimmers) and chemical (e.g. chemical dispersants) methods have been developed to recover and/or disperse oil spilled at sea, they are not 100% effective and are frequently limited by operational constraints attributed to sea state and/or nature of the contamination. As a result, oil spills frequently impact shoreline environments. In situ bioremediation, the addition of substances or modification of habitat at contaminated sites to accelerate natural biodegradation processes, is now recognised as an alternative spill response technology of the remediation of these sites. Recommended for use following the physical removal of bulk oil, this treatment strategy has an operational advantage in that it breaks down and/or removes the residual contamination in place. Laboratory experiments and field trials have demonstrated the feasibility and success of bioremediation strategies such as nutrient enrichment to enhance bacterial degradation of oil on cobble, sand beach and salt marsh environments. With improved knowledge of the factors that limit natural oil degradation rates, the feasibility of other strategies such as phytoremediation, enhanced oil-mineral fines interaction and the addition of oxygen or alternative electron acceptors are now being evaluated. Laboratory and field test protocols are being refined for the selection of effective bioremediation agents and methods of application. It is recommended that future operational guidelines include real time product efficacy test and environmental effects monitoring programs. Termination of treatment should be implemented when: 1) it is no longer effective; 2) the oil has degraded to acceptable biologically benign concentrations; or 3) toxicity due to the treatment is increasing. (Author)

  10. Molecular beam mass spectrometer equipped with a catalytic wall reactor for in situ studies in high temperature catalysis research

    International Nuclear Information System (INIS)

    Horn, R.; Ihmann, K.; Ihmann, J.; Jentoft, F.C.; Geske, M.; Taha, A.; Pelzer, K.; Schloegl, R.

    2006-01-01

    A newly developed apparatus combining a molecular beam mass spectrometer and a catalytic wall reactor is described. The setup has been developed for in situ studies of high temperature catalytic reactions (>1000 deg. C), which involve besides surface reactions also gas phase reactions in their mechanism. The goal is to identify gas phase radicals by threshold ionization. A tubular reactor, made from the catalytic material, is positioned in a vacuum chamber. Expansion of the gas through a 100 μm sampling orifice in the reactor wall into differentially pumped nozzle, skimmer, and collimator chambers leads to the formation of a molecular beam. A quadrupole mass spectrometer with electron impact ion source designed for molecular beam inlet and threshold ionization measurements is used as the analyzer. The sampling time from nozzle to detector is estimated to be less than 10 ms. A detection time resolution of up to 20 ms can be reached. The temperature of the reactor is measured by pyrometry. Besides a detailed description of the setup components and the physical background of the method, this article presents measurements showing the performance of the apparatus. After deriving the shape and width of the energy spread of the ionizing electrons from measurements on N 2 and He we estimated the detection limit in threshold ionization measurements using binary mixtures of CO in N 2 to be in the range of several hundreds of ppm. Mass spectra and threshold ionization measurements recorded during catalytic partial oxidation of methane at 1250 deg. C on a Pt catalyst are presented. The detection of CH 3 · radicals is successfully demonstrated

  11. Molecular beam mass spectrometer equipped with a catalytic wall reactor for in situ studies in high temperature catalysis research

    Science.gov (United States)

    Horn, R.; Ihmann, K.; Ihmann, J.; Jentoft, F. C.; Geske, M.; Taha, A.; Pelzer, K.; Schlögl, R.

    2006-05-01

    A newly developed apparatus combining a molecular beam mass spectrometer and a catalytic wall reactor is described. The setup has been developed for in situ studies of high temperature catalytic reactions (>1000°C), which involve besides surface reactions also gas phase reactions in their mechanism. The goal is to identify gas phase radicals by threshold ionization. A tubular reactor, made from the catalytic material, is positioned in a vacuum chamber. Expansion of the gas through a 100μm sampling orifice in the reactor wall into differentially pumped nozzle, skimmer, and collimator chambers leads to the formation of a molecular beam. A quadrupole mass spectrometer with electron impact ion source designed for molecular beam inlet and threshold ionization measurements is used as the analyzer. The sampling time from nozzle to detector is estimated to be less than 10ms. A detection time resolution of up to 20ms can be reached. The temperature of the reactor is measured by pyrometry. Besides a detailed description of the setup components and the physical background of the method, this article presents measurements showing the performance of the apparatus. After deriving the shape and width of the energy spread of the ionizing electrons from measurements on N2 and He we estimated the detection limit in threshold ionization measurements using binary mixtures of CO in N2 to be in the range of several hundreds of ppm. Mass spectra and threshold ionization measurements recorded during catalytic partial oxidation of methane at 1250°C on a Pt catalyst are presented. The detection of CH3• radicals is successfully demonstrated.

  12. Hydrodynamic analysis application of contaminated groundwater remediation to oil hydrocarbons

    Directory of Open Access Journals (Sweden)

    Pajić Predrag R.

    2017-01-01

    Full Text Available In this paper, the application of the hydrodynamic analysis in the selected ‘pumping and treatment’ remediation method of groundwater hydrocarbon pollution in the case of the Pancevo oil refinery is examined. The applied hydrodynamic analysis represents a regular and necessary approach in modern hydrogeology. Previous chemical analysis of soil and groundwater samples at observation objects revealed their pollution by oil products. New researches included the constraction of 12 piezometric boreholes of varying depths, geoelectric soil sounding, ‘in situ’ measurement of the present contaminant, detected as a hydrophobic phase of LNAPL, chemical analysis of soil and groundwater samples with emphasis on total petroleum hydrocarbons (TPH content, total fats and mineral oils, mercury cations and other characteristic compounds, etc. These researches define the volume of contamination issued by the ‘light’ (LNAPL contamination phase. The selected remediation method for this type of pollution is the ‘Pump and Treat’ method, which implies the pumping of contaminated groundwater from aquifer and their subsequent treatment. A hydrodynamic method was used to select the optimal hydrotechnical solution for LNAPL extraction. On the mathematical model, the prediction calculations for two variant solutions were carried out (‘hydraulic isolation’ and complex for the application of groundwater contamination remediation characterized as front pollution substance (by extraction and injection wells or infiltration pool. By extraction wells performing, it would be possible to remove the LNAPL from the surface of the water with special pumps-skimmers. The importance of the hydrodynamic method application is, in addition to the hydrotechnical solution selection for the LNAPL drainage, the provision of quality basis for the dimensioning of these objects based on the results of the groundwater balance.

  13. CFD Simulations of Soap Separation; CFD-simulering av avsaapning

    Energy Technology Data Exchange (ETDEWEB)

    Birkestad, Per

    2010-07-01

    A part of Vaermeforsk, the 'Skogsindustriella programmet', has identified the possibility to increase the production of tall oil, and hence the competitiveness, in Swedish pulp mills through an increase in the efficiency of the soap separation tanks. Currently, soap is extracted from the black liquor through a sedimentation process where the less dense soap rise to the top of the liquor tank where it is removed through a over-flow ducting at the top of the tank. Vaermeforsk seeks a better understanding of the detailed flow and the separation mechanisms within the liquor tanks and has initiated a study of computational fluid dynamics (CFD) of the tanks. The aim of the study has been threefold; To develop CFD-methods for use in the study of soap separation processes, to investigate the detailed flow within two Swedish liquor tanks and one North American soap skimmer and lastly to develop new design rules for use in future designs of soap separation tanks. The project shows that CFD is a useful tool for the investigation of black liquor and soap flow within a soap separation tank. The CFD simulations of three existing liquor tanks show that the previously used design-rules based on surface loads are inadequate as the actual flow velocities within the tanks are two orders of magnitude larger than those previously used as reference (the surface load). The CFD simulations also show that the black liquor flow, and hence the soap separation, is very sensitive to density variations on the black liquor inlet and temperature variations as small as 1 deg C can significantly affect the liquor flow.

  14. Molecular analysis of bacterial communities and detection of potential pathogens in a recirculating aquaculture system for Scophthalmus maximus and Solea senegalensis.

    Science.gov (United States)

    Martins, Patrícia; Cleary, Daniel F R; Pires, Ana C C; Rodrigues, Ana Maria; Quintino, Victor; Calado, Ricardo; Gomes, Newton C M

    2013-01-01

    The present study combined a DGGE and barcoded 16S rRNA pyrosequencing approach to assess bacterial composition in the water of a recirculating aquaculture system (RAS) with a shallow raceway system (SRS) for turbot (Scophthalmus maximus) and sole (Solea senegalensis). Barcoded pyrosequencing results were also used to determine the potential pathogen load in the RAS studied. Samples were collected from the water supply pipeline (Sup), fish production tanks (Pro), sedimentation filter (Sed), biofilter tank (Bio), and protein skimmer (Ozo; also used as an ozone reaction chamber) of twin RAS operating in parallel (one for each fish species). Our results revealed pronounced differences in bacterial community composition between turbot and sole RAS, suggesting that in the systems studied there is a strong species-specific effect on water bacterial communities. Proteobacteria was the most abundant phylum in the water supply and all RAS compartments. Other important taxonomic groups included the phylum Bacteriodetes. The saltwater supplied displayed a markedly lower richness and appeared to have very little influence on bacterial composition. The following potentially pathogenic species were detected: Photobacterium damselae in turbot (all compartments), Tenacibaculum discolor in turbot and sole (all compartments), Tenacibaculum soleae in turbot (all compartments) and sole (Pro, Sed and Bio), and Serratia marcescens in turbot (Sup, Sed, Bio and Ozo) and sole (only Sed) RAS. Despite the presence of these pathogens, no symptomatic fish were observed. Although we were able to identify potential pathogens, this approach should be employed with caution when monitoring aquaculture systems, as the required phylogenetic resolution for reliable identification of pathogens may not always be possible to achieve when employing 16S rRNA gene fragments.

  15. Molecular analysis of bacterial communities and detection of potential pathogens in a recirculating aquaculture system for Scophthalmus maximus and Solea senegalensis.

    Directory of Open Access Journals (Sweden)

    Patrícia Martins

    Full Text Available The present study combined a DGGE and barcoded 16S rRNA pyrosequencing approach to assess bacterial composition in the water of a recirculating aquaculture system (RAS with a shallow raceway system (SRS for turbot (Scophthalmus maximus and sole (Solea senegalensis. Barcoded pyrosequencing results were also used to determine the potential pathogen load in the RAS studied. Samples were collected from the water supply pipeline (Sup, fish production tanks (Pro, sedimentation filter (Sed, biofilter tank (Bio, and protein skimmer (Ozo; also used as an ozone reaction chamber of twin RAS operating in parallel (one for each fish species. Our results revealed pronounced differences in bacterial community composition between turbot and sole RAS, suggesting that in the systems studied there is a strong species-specific effect on water bacterial communities. Proteobacteria was the most abundant phylum in the water supply and all RAS compartments. Other important taxonomic groups included the phylum Bacteriodetes. The saltwater supplied displayed a markedly lower richness and appeared to have very little influence on bacterial composition. The following potentially pathogenic species were detected: Photobacterium damselae in turbot (all compartments, Tenacibaculum discolor in turbot and sole (all compartments, Tenacibaculum soleae in turbot (all compartments and sole (Pro, Sed and Bio, and Serratia marcescens in turbot (Sup, Sed, Bio and Ozo and sole (only Sed RAS. Despite the presence of these pathogens, no symptomatic fish were observed. Although we were able to identify potential pathogens, this approach should be employed with caution when monitoring aquaculture systems, as the required phylogenetic resolution for reliable identification of pathogens may not always be possible to achieve when employing 16S rRNA gene fragments.

  16. The Aegean Sea incident: A quantitative evaluation of the fate of the oil

    International Nuclear Information System (INIS)

    Bergueiro Lopez, J.R.; Morales Correas, N.; Dominguez Laseca, F.

    1993-01-01

    In December 1992, the tanker Aegean Sea was shipwrecked at the entrance to a harbor in northwest Spain. The accident was partly due to bad weather conditions and possibly also to the poor condition of the ship, which subsequently broke in two and caught fire. The tanker was carrying 79,000 tons of low-viscosity light oil, of which 40-60% burned. The oil slick coming from the wrecked ship spread westward and northward into nearby bays, impacting 100-200 km of coast with varying degrees of severity. Strong winds and stormy sea conditions at the time of the incident favored evaporation and natural dispersion of much of the spilled oil. Spill response and countermeasures included restriction of fishing zones, manual and mechanical cleaning of beaches and nearby rocks, use of pumps and skimmers to recover oil from water and shore, and stirring oil-penetrated sand to ca 50 cm depth to facilitate oxygenation and ensure degradation of oil traces. About 6,000 m 3 of emulsified oil were collected from the water and another 1,000 m 3 from the shore; 5,000-6,000 tons of unspilled oil was recovered from the tanker. A simulation model estimated that if no burning had occurred, 2/3 of the oil would have dispersed in the sea or evaporated into the air in ca 3 d. Ecological impacts on plankton, benthos, and pelagic and bird communities appears to have been minor or at least relatively localized. Long-term ecological impacts are being studied. However, zones of fish/shellfish breeding were affected, with short-term damages estimated at over $45 million. 9 refs., 5 figs., 1 tab

  17. Matrix effects in inductively coupled plasma mass spectrometry

    International Nuclear Information System (INIS)

    Chen, Xiaoshan.

    1995-01-01

    The inductively coupled plasma is an electrodeless discharge in a gas (usually Ar) at atmospheric pressure. Radio frequency energy generated by a RF power source is inductively coupled to the plasma gas through a water cooled load coil. In ICP-MS the open-quotes Fasselclose quotes TAX quartz torch commonly used in emission is mounted horizontally. The sample aerosol is introduced into the central flow, where the gas kinetic temperature is about 5000 K. The aerosol is vaporized, atomized, excited and ionized in the plasma, and the ions are subsequently extracted through two metal apertures (sampler and skimmer) into the mass spectrometer. In ICP-MS, the matrix effects, or non-spectroscopic interferences, can be defined as the type of interferences caused by dissolved concomitant salt ions in the solution. Matrix effects can be divided into two categories: (1) signal drift due to the deposition of solids on the sampling apertures; and/or (2) signal suppression or enhancement by the presence of the dissolved salts. The first category is now reasonably understood. The dissolved salts, especially refractory oxides, tend to deposit on the cool tip of the sampling cone. The clogging of the orifices reduces the ion flow into the ICP-MS, lowers the pressure in the first stage of ICP-MS, and enhances the level of metal oxide ions. Because the extent of the clogging increases with the time, the signal drifts down. Even at the very early stage of the development of ICP-MS, matrix effects had been observed. Houk et al. found out that the ICP-MS was not tolerant to solutions containing significant amounts of dissolved solids

  18. Department of Defense support to spill response operations

    International Nuclear Information System (INIS)

    Ducey, D.L. Jr.; Walker, A.H.

    1993-01-01

    The Department of Defense (DOD), operating through the Directorate of Military Support in the Department of the Army, supports state, local and other federal agency response operations in a wide range of natural and man-caused emergencies. Examples within the past six years include the Ashland Oil tank collapse in Floreffe, Pennsylvania, Exxon Valdez cleanup, Loma Prieta earthquake, hurricanes Hugo and Andrew, Mexico City earthquake, Armero (Columbia) volcanic eruption, and Puerto Rico floods and mud slides. From March 24 to September 27, 1989, the period of the Exxon Valdez initial cleanup operations, DOD provided military and civilian personnel, US Navy ships for housing response workers, cargo and medical evacuation aircraft (fixed wing and helicopters), skimmers, modified dredges, landing craft, Dracones, Zodiak boats, radios, computers, and other miscellaneous equipment. This was in addition to assets of the Alaska Army and Air National Guard, which were committed by the governor. Support was provided to the US Coast Guard on scene coordinator and supervised by the Alaska Oil Spill Joint Task Force. The General Accounting Office, in its January 1990 report, Federal Costs Resulting from the Exxon Valdez Oil Spill, estimated that DOD spent $62.8 million through September 30, 1989, the largest expenditure by any federal agency. Use of military resources is a realistic scenario in certain situations. Primary responders at the federal and state level should understand how to request and employ these assets. This paper provides a background on DOD support to disaster relief operations, and discusses the types of support available to agencies responding to natural or man-caused emergencies, request and approval mechanisms, the Department of Defence organization to provide support, and reimbursement of the department

  19. Tanker self-help spill recovery systems

    Energy Technology Data Exchange (ETDEWEB)

    Smedley, J B; Wainwright, J G; Ehman, T K

    1991-12-01

    An investigation was conducted of the circumstances in which oil spills occur from tankers at sea by analyzing available historical oil spill data. A data base of marine oil spills greater than 134 tonnes occurring from 1974 and June 1990, included in an appendix, was among the information analyzed. The analysis showed that marine oil spills of 5,000 tonnes and greater account for 39.4% of the accidents yet 94.7% of the total spilled quantity; 84% of those spills occur in vessels of 20,000 deadweight tonnes and larger. Of spills over 5,000 tonnes, 78.5% occur outside of harbor or pier areas where spill response equipment may not be readily available. Over 50% of spills are caused by groundings or collisions where the vessel crew might be able to respond in mitigating and controlling the outflow of oil. The review suggested that tanker self-help systems warrant serious consideration. Potential self-help systems are described, ranging from additives such as bioremediation, dispersants, and solidifiers to equipment such as portable pumps, booms, and skimmers. Candidate systems were examined in terms of their safety, ease of operation, practicability, and effectiveness. Their possible performance was then assessed for the case of major marine oil spills that have occurred in Canadian waters. Four systems are identified as potential candidates for further evaluation and possible implementation: internal oil transfer, hydrostatic loading, external oil lightering, and contingency planning. A system design is evaluated and its benefits and possible implementation are outlined, based on integration of the preferred attributes of the above four options. Recommendations for implementation are also provided. 28 refs., 6 figs., 33 tabs.

  20. Some aspects of floating ice related to sea surface operations in the Barents sea

    International Nuclear Information System (INIS)

    Loeset, S.

    1993-01-01

    The present work highlights some aspects of floating ice related to sea surface operations in the Barents sea. The thesis consists of eight papers which fall into two main categories; one part deals with numerical modeling of the temperature distribution and ablation of icebergs (three papers), and the other part studies the behavior of broken ice, focusing on both laboratory experiments and numerical modeling. The temperature distribution within an iceberg affects the mechanical strength of the ice and is therefore crucial in engineering applications when estimating loads from impinging icebergs on offshore structures. A numerical model which simulates the temperature distribution and ablation of icebergs has been developed. The model shows that the depth of the thermal disturbance and slope of the temperature gradient of an iceberg depend on the boundary conditions and the time at sea. By about 12 m into the ice, the temperature is virtually free of any thermal boundary influence. Oil spill response techniques are vulnerable to the presence of sea ice. Deflecting ice upstream of a spill site by means of a flexible boom will facilitate the application of conventional oil spill recovery systems such as oil skimmers and booms. Experiments with such an ice deflecting boom were conducted in an ice tank to determine the loads on the boom and to study the ice-free wake. The study indicated the technical feasibility of the ice boom concept as an operational tool for oil spill cleanups. A two-dimensional discrete element model has been developed. This model simulates the dynamics and interaction forces between distinct ice floes in a broken ice field. The numerical model was applied to estimate the loads on a boom used for ice management. 121 refs., 70 figs., 10 tabs

  1. Long-Term Observations of Epibenthic Fish Zonation in the Deep Northern Gulf of Mexico

    Science.gov (United States)

    Wei, Chih-Lin; Rowe, Gilbert T.; Haedrich, Richard L.; Boland, Gregory S.

    2012-01-01

    A total of 172 bottom trawl/skimmer samples (183 to 3655-m depth) from three deep-sea studies, R/V Alaminos cruises (1964–1973), Northern Gulf of Mexico Continental Slope (NGoMCS) study (1983–1985) and Deep Gulf of Mexico Benthos (DGoMB) program (2000 to 2002), were compiled to examine temporal and large-scale changes in epibenthic fish species composition. Based on percent species shared among samples, faunal groups (≥10% species shared) consistently reoccurred over time on the shelf-break (ca. 200 m), upper-slope (ca. 300 to 500 m) and upper-to-mid slope (ca. 500 to 1500 m) depths. These similar depth groups also merged when the three studies were pooled together, suggesting that there has been no large-scale temporal change in depth zonation on the upper section of the continental margin. Permutational multivariate analysis of variance (PERMANOVA) also detected no significant species changes on the limited sites and areas that have been revisited across the studies (P>0.05). Based on the ordination of the species shared among samples, species replacement was a continuum along a depth or macrobenthos biomass gradient. Despite the well-known, close, negative relationship between water depth and macrofaunal biomass, the fish species changed more rapidly at depth shallower than 1,000 m, but the rate of change was surprisingly slow at the highest macrofaunal biomass (>100 mg C m−2), suggesting that the composition of epibenthic fishes was not altered in response to the extremely high macrofaunal biomass in the upper Mississippi and De Soto Submarine Canyons. An alternative is that the pattern of fish species turnover is related to the decline in macrofaunal biomass, the presumptive prey of the fish, along the depth gradient. PMID:23056412

  2. Long-term observations of epibenthic fish zonation in the deep northern Gulf of Mexico.

    Directory of Open Access Journals (Sweden)

    Chih-Lin Wei

    Full Text Available A total of 172 bottom trawl/skimmer samples (183 to 3655-m depth from three deep-sea studies, R/V Alaminos cruises (1964-1973, Northern Gulf of Mexico Continental Slope (NGoMCS study (1983-1985 and Deep Gulf of Mexico Benthos (DGoMB program (2000 to 2002, were compiled to examine temporal and large-scale changes in epibenthic fish species composition. Based on percent species shared among samples, faunal groups (≥10% species shared consistently reoccurred over time on the shelf-break (ca. 200 m, upper-slope (ca. 300 to 500 m and upper-to-mid slope (ca. 500 to 1500 m depths. These similar depth groups also merged when the three studies were pooled together, suggesting that there has been no large-scale temporal change in depth zonation on the upper section of the continental margin. Permutational multivariate analysis of variance (PERMANOVA also detected no significant species changes on the limited sites and areas that have been revisited across the studies (P>0.05. Based on the ordination of the species shared among samples, species replacement was a continuum along a depth or macrobenthos biomass gradient. Despite the well-known, close, negative relationship between water depth and macrofaunal biomass, the fish species changed more rapidly at depth shallower than 1,000 m, but the rate of change was surprisingly slow at the highest macrofaunal biomass (>100 mg C m(-2, suggesting that the composition of epibenthic fishes was not altered in response to the extremely high macrofaunal biomass in the upper Mississippi and De Soto Submarine Canyons. An alternative is that the pattern of fish species turnover is related to the decline in macrofaunal biomass, the presumptive prey of the fish, along the depth gradient.

  3. Long-term observations of epibenthic fish zonation in the deep northern Gulf of Mexico.

    Science.gov (United States)

    Wei, Chih-Lin; Rowe, Gilbert T; Haedrich, Richard L; Boland, Gregory S

    2012-01-01

    A total of 172 bottom trawl/skimmer samples (183 to 3655-m depth) from three deep-sea studies, R/V Alaminos cruises (1964-1973), Northern Gulf of Mexico Continental Slope (NGoMCS) study (1983-1985) and Deep Gulf of Mexico Benthos (DGoMB) program (2000 to 2002), were compiled to examine temporal and large-scale changes in epibenthic fish species composition. Based on percent species shared among samples, faunal groups (≥10% species shared) consistently reoccurred over time on the shelf-break (ca. 200 m), upper-slope (ca. 300 to 500 m) and upper-to-mid slope (ca. 500 to 1500 m) depths. These similar depth groups also merged when the three studies were pooled together, suggesting that there has been no large-scale temporal change in depth zonation on the upper section of the continental margin. Permutational multivariate analysis of variance (PERMANOVA) also detected no significant species changes on the limited sites and areas that have been revisited across the studies (P>0.05). Based on the ordination of the species shared among samples, species replacement was a continuum along a depth or macrobenthos biomass gradient. Despite the well-known, close, negative relationship between water depth and macrofaunal biomass, the fish species changed more rapidly at depth shallower than 1,000 m, but the rate of change was surprisingly slow at the highest macrofaunal biomass (>100 mg C m(-2)), suggesting that the composition of epibenthic fishes was not altered in response to the extremely high macrofaunal biomass in the upper Mississippi and De Soto Submarine Canyons. An alternative is that the pattern of fish species turnover is related to the decline in macrofaunal biomass, the presumptive prey of the fish, along the depth gradient.

  4. Hematological indices of injury to lightly oiled birds from the Deepwater Horizon oil spill

    Science.gov (United States)

    Fallon, Jesse A.; Smith, Eric P.; Schoch, Nina; Paruk, James D.; Adams, Evan A.; Evers, David C.; Jodice, Patrick G. R.; Perkins, Christopher; Schulte, Shiloh A.; Hopkins, William A.

    2018-01-01

    Avian mortality events are common following large‐scale oil spills. However, the sublethal effects of oil on birds exposed to light external oiling are not clearly understood. We found that American oystercatchers (area of potential impact n = 42, reference n = 21), black skimmers (area of potential impact n = 121, reference n = 88), brown pelicans (area of potential impact n = 91, reference n = 48), and great egrets (area of potential impact n = 57, reference n = 47) captured between 20 June 2010 and 23 February 2011 following the Deepwater Horizon oil spill experienced oxidative injury to erythrocytes, had decreased volume of circulating erythrocytes, and showed evidence of a regenerative hematological response in the form of increased reticulocytes compared with reference populations. Erythrocytic inclusions consistent with Heinz bodies were present almost exclusively in birds from sites impacted with oil, a finding pathognomonic for oxidative injury to erythrocytes. Average packed cell volumes were 4 to 19% lower and average reticulocyte counts were 27 to 40% higher in birds with visible external oil than birds from reference sites. These findings provide evidence that small amounts of external oil exposure are associated with hemolytic anemia. Furthermore, we found that some birds captured from the area impacted by the spill but with no visible oiling also had erythrocytic inclusion bodies, increased reticulocytes, and reduced packed cell volumes when compared with birds from reference sites. Thus, birds suffered hematologic injury despite no visible oil at the time of capture. Together, these findings suggest that adverse effects of oil spills on birds may be more widespread than estimates based on avian mortality or severe visible oiling.

  5. Multielement analysis of Zanthoxylum bungeanum Maxim. essential oil using ICP-MS/MS.

    Science.gov (United States)

    Fu, Liang; Xie, Hualin; Shi, Shuyun

    2018-04-12

    The concentrations of trace elements (Cr, Ni, As, Cd, Hg, and Pb) in Zanthoxylum bungeanum Maxim. essential oil (ZBMEO) were determined by inductively coupled plasma tandem mass spectrometry. The ZBMEO sample was directly analyzed after simple dilution with n-hexane. Aiming for a relatively high vapor pressure of n-hexane and its resultant loading on plasma, we used a narrow injector torch and optimized plasma radio frequency power and carrier gas flow to ensure stable operation of the plasma. An optional gas flow of 20% O 2 in Ar was added to the carrier gas to prevent the incomplete combustion of highly concentrated organic carbon in plasma and the deposition of carbon on the sampling and skimmer cone orifices. In tandem mass spectrometry mode, O 2 was added to the collision/reaction cell to eliminate the interferences. The limits of detection for Cr, Ni, As, Cd, Hg, and Pb were 2.26, 1.64, 2.02, 1.35, 1.76, and 0.97 ng L -1 , respectively. After determination of 23 ZBMEO samples from different regions in China, we found that the average concentration ranges of trace elements in the 23 ZBMEO samples were 0.72-6.02 ng g -1 , 0.09-2.87 ng g -1 , 0.21-5.84 ng g -1 , 0.16-2.15 ng g -1 , 0.13-0.92 ng g -1 , and 0.17-0.73 ng g -1 for Cr, Ni, As, Cd, Hg, and Pb, respectively. The trace elements in ZBMEO differed significantly when different extraction technologies were used. The study revealed that the contents of the toxic elements As, Cd, Hg, and Pb were extremely low, and hence they are unlikely to pose a health risk following ZBMEO ingestion. Graphical abstract The working mechanism of sample analysis by ICP-MS/MS.

  6. The USCG/environment Canada/ASTM standards development program

    International Nuclear Information System (INIS)

    Whittaker, H.

    1992-01-01

    Environment Canada's Emergencies Engineering Division (EED) has been charged, as a result of the Public Review Panel on Tanker Safety and Marine Emergency Response report, with increased R ampersand D in marine oil spills. This activity will, of necessity, include development of standards and guidelines for the testing and/or usage of oil spill cleanup equipment. The United States Coast Guard (USCG) has been charged with implementing the provisions of the Oil Pollution Act of 1990 (OPA-90), as it pertains to marine transportation vessels and facilities. Among the provisions are requirements for vessel and facility owners and operators to develop comprehensive response plans that specifically match response resources to spill removal requirements. Meeting the response plan provisions of OPA-90 requires common standards for testing, selecting and assigning resources to anticipated response needs and objectively evaluating response plans for adequacy. In August of 1991, the USCG OPA-90 office approached ASTM to determine the feasibility of developing standards through that organizations procedures. Meetings were then held between the OPA-90 staff and members of the ASTM Committee F-20 on Hazardous Substances and Oil Spill Response. An agreement was reached to commence standards development in the areas of: Barriers, Skimmers, Treating Agents, Pumps, Beach Clean-up, Sorbents, Bioremediation, In-situ Burning, Temporary Storage Devices, Communications, Remote Sensing. It was recognized that ASTM and other organizational standards existed in several of these areas, but there were those where none were known to exist. Standards development was, therefore, expected to be a complicated and time-consuming process. Both the USCG OPA-90 and EC/EED offices required standards to be developed quickly, without subverting the ASTM process. Mechanical containment and recovery was considered to be the primary area of concern for both groups

  7. Vacuum recovery of free phased leaded gasoline plume Naval Air Station Oceana, Virginia Beach, Virginia

    International Nuclear Information System (INIS)

    Conway, J.D.; DeLattre, E.L.S.; Beatty, T.R.

    1999-01-01

    Much attention has been paid to the remediation and site restoration of contaminated sites resulting from gasoline and diesel underground storage tanks. These sites are generally associated with fuel delivery systems and are readily visible to the public. One such site is located within the Naval Air Station (NAS) Oceana, Virginia Beach, Virginia. The remediation site is located on an active gas station within NAS Oceana. The scope of the project was to construct a dual-phase remediation system for the removal of free product and the treatment of contaminated groundwater. Contaminated groundwater was to have been collected form recovery wells and conveyed via an underground conveyance system to the treatment system. The treatment system would have contained all the necessary equipment to extract groundwater from the subsurface. The estimated effluent limit for lead would necessitate removal of lead with associated modifications to the treatment system design. Such modifications were financially unfeasible; thus, an alternative remediation scheme had to be designed. LANTDIV decided on a remediation scheme that involved product-only recovery via solar-powered product skimmers and free product removal through vapor extraction. The estimated volume of product in the ground prior to starting the system was 18,000 gallons. The volume of product in the ground after one year of operation is estimated to be 11,700 gallons, reducing the total volume by one-third in the first year of operation. Project thickness that was originally measured at >1.0 foot in six monitoring wells in October 1997 is now present in only three wells at a thickness >0.5 feet. This remediation was accomplished using a treatment system that required minimal capital cost and is simple to operate, thereby keeping operation and maintenance (O and M) cost to a minimum

  8. Threatened and Endangered Species Survey for Patrick Air Force Base, Florida

    Science.gov (United States)

    Oddy, Donna M.; Stolen, Eric D.; Schmalzer, Paul A.; Larson, Vickie L.; Hall, Patrice; Hensley, Melissa A.

    1997-01-01

    characteristic of species that occur in the Indian River Lagoon system. Twenty-five species of waterbirds were observed during quarterly surveys on PAFB, including five species listed as species of special concern by the state of Florida: Snowy Egret (Egretta thula), Little Blue Heron (Egretta caerulea), Tricolored Heron (Egretta tricolo4, White Ibis (Eudocimus albus), and Brown Pelican (Pelecanus occidentalis). The Golf Course was used extensively by almost all species of waterbirds on PAFB. Twenty-two species of shorebirds were observed on PAFB. Although no listed species were observed, the potential exists for several protected species of shorebirds to use the beach at PAFB during some parts of the year. The Airfield runways and associated grass areas were important sites at PAFB for loafing and feeding for some shorebirds. Surveys of rooftop nesting by Least Terns (Stema antillarum) on PAFB found a large colony on a rooftop in the PAFB Industrial Area. This colony produced some independent young. Two rooftop Least Tern colonies reported from previous years were inactive during 1996. A small number of Black Skimmers (Rhynchops nigee attempted to nest at the Least Ten colony but were unsuccessful. Surveys for the gopher tortoise (Gopherus polyphemus) revealed burrows and tortoises only at the Waste Study Site; five burrows and three tortoises were observed. No Florida scrub lizards (Sceloporus woodi), eastern indigo snakes (Drymarchon corais couperl), or diamondback terrapins (Malademys terrapin terrapin) were observed. American alligators (Alligator mississippiensis) were observed on the Golf Course and using ditches, ponds, and areas along the Banana River. The amount of dune habitat could be expanded by not mowing areas adjacent to the dunes to allow dune species to colonize and expand. Planting dune species as part of the beach renourishment project will also increase this habitat. Exotic plants dominate several areas on the base and are used by threatened, endangered, and

  9. Analytical strategy for the determination of various arsenic species in landfill leachate containing high concentrations of chlorine and organic carbon by HPLC-ICPMS

    Science.gov (United States)

    Bae, J.; An, J.; Kim, J.; Jung, H.; Kim, K.; Yoon, C.; Yoon, H.

    2012-12-01

    As a variety of wastes containing arsenic are disposed of in landfills, such facilities can play a prominent role in disseminating arsenic sources to the environment. Since it is widely recognized that arsenic toxicity is highly dependent on its species, accurate determination of various arsenic species should be considered as one of the essential goals to properly account for the potential health risk of arsenic in human and the environment. The inductively coupled plasma mass spectrometry linked to high performance liquid chromatography (HPLC-ICPMS) is acknowledged as one of the most important tools for the trace analysis of metallic speciation because of its superior separation capability and detectability. However, the complexity of matrices can cause severe interferences in the analysis results, which is the problem often encountered with HPLC-ICPMS system. High concentration of organic carbon in a sample solution causes carbon build-up on the skimmer and sampling cone, which reduces analytical sensitivity and requires a high maintenance level for its cleaning. In addition, argon from the plasma and chlorine from the sample matrix may combine to form 40Ar35Cl, which has the same nominal mass to charge (m/z) ratio as arsenic. In this respect, analytical strategy for the determination of various arsenic species (e.g., inorganic arsenite and arsenate, monomethylarsonic acid, dimethylarsinic acid, dimethyldithioarsinic acid, and arsenobetaine) in landfill leachate containing high concentrations of chlorine and organic carbon was developed in the present study. Solid phase extraction disk (i.e., C18 disk), which does not significantly adsorb any target arsenic species, was used to remove organic carbon in sample solutions. In addition, helium (He) gas was injected into the collision reaction cell equipped in ICPMS to collapse 40Ar35Cl into individual 40Ar and 35Cl. Although He gas also decreased arsenic intensity by blocking 75As, its signal to noise ratio

  10. Research on using oil herding surfactants to thicken oil slicks in pack ice for in situ burning

    International Nuclear Information System (INIS)

    Buist, I.; Morrison, J.

    2005-01-01

    The severe limitations of conventional containment and recovery systems for oil spills in pack ice have been demonstrated during skimmer tests conducted in the Alaskan Beaufort Sea. In-situ burning may be one of the few viable alternatives to quickly remove oil spilled in pack ice, but the slicks are often too thin, preventing effective ignition or burning. This study examined ways to thicken the slicks to the 2- to 5-mm range so that effective burns could be carried out. Specific chemical surface-active agents known as oil herders or oil collecting agents can be used to clear and contain oil slicks on water surfaces. Since these agents can spread quickly on water, only a small quantity is needed to clear thin films of oil from large areas of water. Applying a chemical herder around the periphery of spilled oil can contract the oil into a thicker slick. Two chemical products were developed and tested in the 1970s and 1980s: Shell Herder and Exxon OC-5 Oil Collector. However, they are no longer used because they were effective only in very calm conditions. Corexit EC9580 which exhibits similar slick herding abilities and which has a spreading pressure of 39.5 mN/m is still commercially available. This study tested formulations of herding agents for use in pack ice. Concerns regarding the potential toxicity risk of using these agents in pack ice were also addressed. The agents should not harm the environment because they have low toxicity and only very small quantities are used. Two series of tests conducted to assess the potential for herding agents to help ignite and effectively burn thin oil slicks in loose pack ice conditions. The agents proved to be effective on cold water and on thick slicks. The composition of the oil played an important role in determining potential efficiency. It was concluded that applying herders to thin oil slicks in pack ice shows considerable promise for thickening them for in-situ burning. 12 refs., 4 tabs., 17 figs

  11. Simple setup for gas-phase H/D exchange mass spectrometry coupled to electron transfer dissociation and ion mobility for analysis of polypeptide structure on a liquid chromatographic time scale.

    Science.gov (United States)

    Mistarz, Ulrik H; Brown, Jeffery M; Haselmann, Kim F; Rand, Kasper D

    2014-12-02

    Gas-phase hydrogen/deuterium exchange (HDX) is a fast and sensitive, yet unharnessed analytical approach for providing information on the structural properties of biomolecules, in a complementary manner to mass analysis. Here, we describe a simple setup for ND3-mediated millisecond gas-phase HDX inside a mass spectrometer immediately after ESI (gas-phase HDX-MS) and show utility for studying the primary and higher-order structure of peptides and proteins. HDX was achieved by passing N2-gas through a container filled with aqueous deuterated ammonia reagent (ND3/D2O) and admitting the saturated gas immediately upstream or downstream of the primary skimmer cone. The approach was implemented on three commercially available mass spectrometers and required no or minor fully reversible reconfiguration of gas-inlets of the ion source. Results from gas-phase HDX-MS of peptides using the aqueous ND3/D2O as HDX reagent indicate that labeling is facilitated exclusively through gaseous ND3, yielding similar results to the infusion of purified ND3-gas, while circumventing the complications associated with the use of hazardous purified gases. Comparison of the solution-phase- and gas-phase deuterium uptake of Leu-Enkephalin and Glu-Fibrinopeptide B, confirmed that this gas-phase HDX-MS approach allows for labeling of sites (heteroatom-bound non-amide hydrogens located on side-chains, N-terminus and C-terminus) not accessed by classical solution-phase HDX-MS. The simple setup is compatible with liquid chromatography and a chip-based automated nanoESI interface, allowing for online gas-phase HDX-MS analysis of peptides and proteins separated on a liquid chromatographic time scale at increased throughput. Furthermore, online gas-phase HDX-MS could be performed in tandem with ion mobility separation or electron transfer dissociation, thus enabling multiple orthogonal analyses of the structural properties of peptides and proteins in a single automated LC-MS workflow.

  12. The exotic mute swan (Cygnus olor) in Chesapeake Bay, USA

    Science.gov (United States)

    Perry, M.C.; Perry, M.C.

    2002-01-01

    The exotic mute swan (Cygnus olor) has increased its population size in Chesapeake Bay (Maryland and Virginia) to approximately 4,500 since 1962 when five swans were released in the Bay. The Bay population of mute swans now represents 30% of the total Atlantic Flyway population (12,600) and has had a phenomenal increase of 1,200% from 1986 to 1999. Unlike the tundra swans (Cygnus columbianus) that migrate to the Bay for the winter, the mute swan is a year-long resident, and, therefore, reports of conflicts with nesting native waterbirds and the consumption of submerged aquatic vegetation (SAV) have raised concerns among resource managers. Populations of black skimmers (Rynchops niger) and least terns (Sterna antillarum) nesting on beaches and oyster shell bars have been eliminated by molting mute swans. Although data on the reduction of SAV by nesting mute swans and their offspring during the spring and summer are limited, food habits data show that mute swans rely heavily on SAV during these months. Widgeon grass (Ruppia maritima) constituted 56% and eel grass (Zostera marina) constituted 43% of the gullet food of mute swans. Other SAV and invertebrates (including bryozoans, shrimp, and amphipods) formed a much smaller amount of the food percentage (1%). Invertebrates are believed to have been selected accidently within the vegetation eaten by the swans. Corn (Zea mays) fed to swans by Bay residents during the winter probably supplement limited vegetative food resources in late winter. A program to control swan numbers by the addling of eggs and the killing of adult swans has been a contentious issue with some residents of the Bay area. A management plan is being prepared by a diverse group of citizens appointed by the Governor to advise the Maryland Department of Natural Resources on viable and optimum options to manage mute swans in the Maryland portion of Chesapeake Bay. Hopefully, the implementation of the plan will alleviate the existing conflicts to the

  13. US Coast Guard national spill response resource inventory

    International Nuclear Information System (INIS)

    Giraitis, D.M.

    1993-01-01

    The Oil Pollution Act of 1990 (OPA 90) mandated the establishment of a National Response Unit, now renamed the National Strike Force Coordination Center (NSFCC). Among the duties OPA 90 assigned to this new Coast Guard unit was to compile and maintain a comprehensive list of spill removal resources, personnel, and equipment that is available to Federal and State agencies and to the public. The Coast Guard's Research and Development Center has been developing this project, the Response Resource Inventory (RRI), for one year. The RRI is expected to be operational, with resource data from industry in the data base, by the time of the International Oil Spill Conference in March 1993. The RRI will contain data on skimmers, specialized oil recovery vessels, oil/water separators, dispersants and delivery systems, etc. Previous attempts to maintain a national data base of these response resources, including an earlier Coast Guard system called the Spill Cleanup Equipment Inventory System (SKIM), fell into disuse for a number of reasons. Inaccuracies caused by inadvertent double counting of equipment and outdated information coupled with difficulties in accessing the information were common shortfalls of early systems. During the development of the RRI, user-group meetings were held to determine system requirements and study the failures of previous systems. Methods of obtaining and entering data were a major concern during RRI development. A data collection system that supplies the resource holder with a DOS-formatted diskette containing a collection program will be used. The program will make extensive use of pick lists to minimize the data entry burden on the resource holder and maintain standard entries. When the program is completed, the diskette will be mailed to the NSFCC, where the data will be transferred quickly to the RRI data base. Easy access to the data for the public and industry will be afforded mainly through a computer bulletin board

  14. Characterisation of chemically-modified proteins by electrospray ionisation mass spectrometry

    International Nuclear Information System (INIS)

    Bennett, K.L.

    1996-09-01

    Electrospray mass spectrometry (ESI-MS) has been used to examine a range of intact monoclonal antibodies (MAbs), antibody fragments such as F(ab') 2 , F ab and F c , chemically-modified fragments and a range of other chemically-modified peptides and proteins as part of a broader study aimed at establishing ESI-MS as a method for the characterisation of radioimmunoconjugates (radiolabelled monoclonal antibodies). For example, the addition of up to 10 biotin molecules to the 'papain-sensitive' 50 kDa F ab fragment can be easily detected in ESI mass spectra. For intact MAbs, however, it is only possible to detect average shifts in the mass of intact antibodies following modification. Successful ESI-MS analysis of complexes formed between chelators and other small molecules conjugated to synthetic peptides, hen egg-white Iysozyme (HEL) (M r 14 306) and horse heart myoglobin (M r 16 951) has been demonstrated. ESI-MS offers considerable advantages compared with existing methods for the characterisation of chemically-conjugated proteins including speed and sensitivity of analysis and the capability for obtaining specific structural information. The conditions for ESI-MS of intact MAbs and MAb fragments have been examined in detail and it was found that 150 kDa MAbs generally required lower sample concentration and higher skimmer potentials compared with the 50 kDa F ab fragment and other lower molecular weight proteins. In addition, the m/z range over which ions from MAbs were observed was higher (m/z ∼2000-4500) than for smaller proteins. ESI-MS was also found to be useful for probing the action of the protease papain, that is used to generate MAb fragments (F(ab) '2, F ab and F c ). Further, different sensitivities to papain for different MAb preparations was demonstrated. Finally, the tandem mass spectra of a range of peptides modified by iodine and biotin were examined. In the case of biotinylated peptides, a characteristic fragment ion was identified that could

  15. Petrol contaminated groundwater treatment with air-stripper in Balassagyarmat, Hungary

    International Nuclear Information System (INIS)

    Szabo, Peter; Bernath, Balazs

    2005-01-01

    Hydrocarbon contaminated groundwater is a common environmental problem in Hungary. Leakage of underground storage tanks, pipe break or illegal tapping as well as lorry accidents can be mentioned as main reasons. MEGATERRA Ltd. elaborated, adopted and tested several groundwater clean-up methods. These methods are based on detailed survey and investigation, sampling and analysis, delineation of contaminated groundwater, risk assessment, establishment of monitoring wells, pumping tests and remediation action plan. One of these methods was implemented by MEGATERRA Ltd. in Balassagyarmat, Hungary. Contamination source was a 10 m 3 vol. simple wall underground fuel-storage tank, which had been emptied. When the remediation started in April 1998, the petrol had already been accumulated on the ground water table forming a 5-7 m wide and 10-15 m long plume being expanded to SSE-NNW direction. The area of the dissolved hydrocarbon contaminated groundwater-body was 1 000 m 2 and its concentration reached up to 30-40 mg/l TPH. The free-phase hydrocarbon layer was 10 cm thick. For the remediation of contaminated groundwater MEGATERRA Ltd. applied pump and treat method, namely groundwater pumping using extraction well, skimming of free-phase hydrocarbon, stripping of the contaminated ground water in air-stripper tower and draining of the treated groundwater into a drainage ditch. In the centre of the plume we established an extraction well with 300 mm diameter in a 500 mm borehole. Peristaltic skimmer pump was used inside the extraction well to remove the free phase petrol from the ground water surface.Because of the intense volatility of the pollutant we applied aeration (stripping) technology. The extracted contaminated groundwater was cleaned in air-stripper equipment being able to eliminate efficiently the volatile pollutants from the water. The aeration tower is a compact cylindrical shaped column with 650 mm in diameter. Its height depends on the pollutant's type The

  16. Diversidade e abundância sazonal da avifauna em duas planícies de maré no estuário da baía da Babitonga, norte de Santa Catarina Diversity and abundance of birds in two tidal flat in Babitonga Bay estuary, north of Santa Catarina state, Brazil

    Directory of Open Access Journals (Sweden)

    Alexandre V. Grose

    2013-03-01

    Full Text Available Informações sobre a ocorrência de aves nos ambientes estuarinos de Santa Catarina ainda são escassas. O objetivo deste trabalho foi registrar a diversidade, abundância e variação sazonal das aves em duas planícies de maré na baía da Babitonga. As amostragens foram realizadas durante um ano (maio de 2006 a abril 2007. No total foram identificadas 25 espécies, sendo 15 no Linguado (LG e 24 na desembocadura do Monte de Trigo (MT. Apenas uma espécie foi exclusiva no LG Himantopus melanurus (Vieillot, 1817, enquanto dez espécies ocorreram apenas no MT. O número de espécies em MT foi superior ao encontrado em LG. A espécie mais abundante em MT foi Rynchops niger (Linnaeus, 1758 e em LG foi Egretta caerulea (Linnaeus, 1758. Durante alguns meses foram registradas espécies migratórias neárticas em ambas as áreas, o que representou um acréscimo na diversidade. A extensa planície de maré formada pelo fechamento do canal do Linguado tem sido muito ocupada por aves, possivelmente pela maior disponibilidade de alimento.Information of birds in estuaries of Santa Catarina is scarce. This work aimed to collect data on diversity, abundance and seasonal variation on this community. Sampling of birds in two tidal flats in Babitonga Bay estuary was carried out during one year (May 2006 to April 2007. A total of 25 species were identified, being 15 in Linguado (LG and 24 in Monte de Trigo (MT. Only one species was unique in LG (Himantopus melanurus Vieillot, 1817 and 10 in MT. The number of species in MT was higher than in LG due to the conservation condition. The most abundant species on MT was the Black Skimmer [Rynchops niger (Linnaeus, 1758] and in the LG was the Little Blue Heron [Egretta caerulea (Linnaeus, 1758]. During some months Nearctic migratory species were recorded in both areas, representing an increase in diversity. The extensive tidal flat formed by the closure of the channel in LG is widely used by birds, possibly because of

  17. New techniques on oil spill modelling applied in the Eastern Mediterranean sea

    Science.gov (United States)

    Zodiatis, George; Kokinou, Eleni; Alves, Tiago; Lardner, Robin

    2016-04-01

    Small or large oil spills resulting from accidents on oil and gas platforms or due to the maritime traffic comprise a major environmental threat for all marine and coastal systems, and they are responsible for huge economic losses concerning the human infrastructures and the tourism. This work aims at presenting the integration of oil-spill model, bathymetric, meteorological, oceanographic, geomorphological and geological data to assess the impact of oil spills in maritime regions such as bays, as well as in the open sea, carried out in the Eastern Mediterranean Sea within the frame of NEREIDs, MEDESS-4MS and RAOP-Med EU projects. The MEDSLIK oil spill predictions are successfully combined with bathymetric analyses, the shoreline susceptibility and hazard mapping to predict the oil slick trajectories and the extend of the coastal areas affected. Based on MEDSLIK results, oil spill spreading and dispersion scenarios are produced both for non-mitigated and mitigated oil spills. MEDSLIK model considers three response combating methods of floating oil spills: a) mechanical recovery using skimmers or similar mechanisms; b) destruction by fire, c) use of dispersants or other bio-chemical means and deployment of booms. Shoreline susceptibility map can be compiled for the study areas based on the Environmental Susceptibility Index. The ESI classification considers a range of values between 1 and 9, with level 1 (ESI 1) representing areas of low susceptibility, impermeable to oil spilt during accidents, such as linear shorelines with rocky cliffs. In contrast, ESI 9 shores are highly vulnerable, and often coincide with natural reserves and special protected areas. Additionally, hazard maps of the maritime and coastal areas, possibly exposed to the danger on an oil spill, evaluate and categorize the hazard in levels from low to very high. This is important because a) Prior to an oil spill accident, hazard and shoreline susceptibility maps are made available to design

  18. Operational Satellite-based Surface Oil Analyses (Invited)

    Science.gov (United States)

    Streett, D.; Warren, C.

    2010-12-01

    During the Deepwater Horizon spill, NOAA imagery analysts in the Satellite Analysis Branch (SAB) issued more than 300 near-real-time satellite-based oil spill analyses. These analyses were used by the oil spill response community for planning, issuing surface oil trajectories and tasking assets (e.g., oil containment booms, skimmers, overflights). SAB analysts used both Synthetic Aperture Radar (SAR) and high resolution visible/near IR multispectral satellite imagery as well as a variety of ancillary datasets. Satellite imagery used included ENVISAT ASAR (ESA), TerraSAR-X (DLR), Cosmo-Skymed (ASI), ALOS (JAXA), Radarsat (MDA), ENVISAT MERIS (ESA), SPOT (SPOT Image Corp.), Aster (NASA), MODIS (NASA), and AVHRR (NOAA). Ancillary datasets included ocean current information, wind information, location of natural oil seeps and a variety of in situ oil observations. The analyses were available as jpegs, pdfs, shapefiles and through Google, KML files and also available on a variety of websites including Geoplatform and ERMA. From the very first analysis issued just 5 hours after the rig sank through the final analysis issued in August, the complete archive is still publicly available on the NOAA/NESDIS website http://www.ssd.noaa.gov/PS/MPS/deepwater.html SAB personnel also served as the Deepwater Horizon International Disaster Charter Project Manager (at the official request of the USGS). The Project Manager’s primary responsibility was to acquire and oversee the processing and dissemination of satellite data generously donated by numerous private companies and nations in support of the oil spill response including some of the imagery described above. SAB has begun to address a number of goals that will improve our routine oil spill response as well as help assure that we are ready for the next spill of national significance. We hope to (1) secure a steady, abundant and timely stream of suitable satellite imagery even in the absence of large-scale emergencies such as

  19. Waterbirds (other than Laridae nesting in the middle section of Laguna Cuyutlán, Colima, México

    Directory of Open Access Journals (Sweden)

    Eric Mellink

    2008-03-01

    Full Text Available Laguna de Cuyutlán, in the state of Colima, Mexico, is the only large coastal wetland in a span of roughly 1150 km. Despite this, the study of its birds has been largely neglected. Between 2003 and 2006 we assessed the waterbirds nesting in the middle portion of Laguna Cuyutlán, a large tropical coastal lagoon, through field visits. We documented the nesting of 15 species of non-Laridae waterbirds: Neotropic Cormorant (Phalacrocorax brasilianus, Tricolored Egret (Egretta tricolor, Snowy Egret (Egretta thula, Little Blue Heron (Egretta caerulea, Great Egret (Ardea alba, Cattle Egret (Bubulcus ibis, Black-crowned Nightheron (Nycticorax nycticorax, Yellow-crowned Night-heron (Nyctanassa violacea, Green Heron (Butorides virescens, Roseate Spoonbill (Platalea ajaja, White Ibis (Eudocimus albus, Black-bellied Whistling-duck (Dendrocygna autumnalis, Clapper Rail (Rallus longirostris, Snowy Plover (Charadrius alexandrinus, and Black-necked Stilt (Himantopus mexicanus. These add to six species of Laridae known to nest in that area: Laughing Gulls (Larus atricilla, Royal Terns (Thalasseus maximus, Gull-billed Terns (Gelochelidon nilotica, Forster’s Terns (S. forsteri, Least Terns (Sternula antillarum, and Black Skimmer (Rynchops niger, and to at least 57 species using it during the non-breeding season. With such bird assemblages, Laguna Cuyutlán is an important site for waterbirds, which should be given conservation status. Rev. Biol. Trop. 56 (1: 391-397. Epub 2008 March 31.Durante la prospección de la parte media de la Laguna Cuyutlán, una gran laguna costera en Colima, México, entre 2003 y 2006, documentamos la anidación de 15 especies de aves acuáticas que no pertenecer a la familia Laridae: Phalacrocorax brasilianus, Egretta tricolor, Egretta thula, Egretta caerulea, Ardea alba, Bubulcus ibis, Nycticorax nycticorax, Nyctanassa violacea, Butorides virescens, Platalea ajaja, Eudocimus albus, Dendrocygna autumnalis, Rallus longirostris

  20. Measurement of argon concentrations in a TRIGA Mark-III pool

    Energy Technology Data Exchange (ETDEWEB)

    Simms, R [California State University, Northridge, CA (United States)

    1974-07-01

    {sup 40}A concentration increases slightly below this point, but the distribution is relatively more uniform throughout the pool than assumed by the usual argon release model. The {sup 41}A count rate distribution, a relative measure, suggests that the dissolved {sup 41}A distribution is also relatively uniform throughout the pool, an apparent consequence of the recirculation rate provided by the pool cooling system. Although unsubstantiated, reductions in {sup 40}A concentration might be achieved by redesign of the pool skimmer and the diffuser pump to reduce air input into the lower pool region. (author)

  1. Pre-electrospray ionisation manifold methylation and post-electrospray ionisation manifold cleavage/ion cluster formation observed during electrospray ionisation of chloramphenicol in solutions of methanol and acetonitrile for liquid chromatography-mass spectrometry employing a commercial quadrupole ion trap mass analyser.

    Science.gov (United States)

    Sichilongo, Kwenga F; Famuyiwa, Samson O; Kibechu, Rose

    2011-01-01

    the tube lens offset voltage is swung to +40 V, thus decelerating the ions through the capillary skimmer region via the tube lens, the traditionally observed spectra with m/z 321, m/z 323 and m/z 325 were observed.

  2. On the simultaneous deployment of two single-particle mass spectrometers at an urban background and a roadside site during SAPUSS

    Directory of Open Access Journals (Sweden)

    M. Dall'Osto

    2016-08-01

    types mainly containing organic carbon were found spiking at different types of the day, also showing a complex single-particle mixing state relationship between organic carbon and nitrate. This ATOFMS study clearly shows that the composition of atmospheric fine particles in Barcelona, and likely other Mediterranean urban areas, is complex, with a wide range of local and regional sources combining with chemical processing to produce at least 22 different particle types exhibiting different temporal behaviour. The advantage of using two ATOFMS instruments is also demonstrated, with the nozzle-skimmer configuration enabling detection of coarse dust particles and the aerodynamic lens configuration allowing better identification of particles rich in organic carbon and amines. Overall, we find that organic nitrogen is a considerable fraction of the single particles detected, especially at the traffic-dominated RS site. Further studies are needed, especially at high time resolution, to better understand the sources and properties of particulate organic nitrogen.

  3. Authenticated, private, and secured smart cards (APS-SC)

    Science.gov (United States)

    Szu, Harold; Mehmood, Amir

    2006-04-01

    -software combined hybrid approach because of a too limited phase space of a single RFID for any meaningful encryption approach. Furthermore, a useful biological lesson is not to put all eggs in one basket, "if you don't get it all, you can't hack it". According to the Radar physics, we can choose the amplitude, the frequency, the phase, the polarization, and two radiation energy supply principles, the capacitance coupling (~6m) and the inductance coupling (<1m), to code the pair of tags differently. A casual skimmer equipped with single-mode reader can not read all. We consider near-field and mid-field applications each in this paper. The near-field is at check-out counters or the convey-belt inventory involving sensitive and invariant data. The mid-field search & rescue involves not only item/person identification, but also the geo-location. If more RF power becomes cheaper & portable for longer propagation distance in the near future, then a triangulation with pair of secured readers, located at known geo-locations, could interrogate and identify items/persons and their locations in a GPS-blind environment.

  4. Process Optimization for Solid Extraction, Flavor Improvement and Fat Removal in the Production of Soymilk From Full Fat Soy Flakes

    Energy Technology Data Exchange (ETDEWEB)

    Prawiradjaja, Stanley [Iowa State Univ., Ames, IA (United States)

    2003-01-01

    lower than the undeodorized triple null and HPSF soymilk. The triple null soymilk was perceived to be more bitter than the HPSF soymilk by the sensory panel due to oxidation on the triple null soy flakes. This oxidation may produce other aroma that was not analyzed using the GC but noticed by the panelists. The sensory evaluation results did show that the deodorizer was able to reduce the soymilk aroma in HPSF soymilk so it would be similar to triple null soymilk at 8 °Brix level. Regardless of skimming method and solids levels, the fat from the whole soybean milk was removed less efficiently than soy flake milk (7 to 30% fat extraction in contrast to 50 to 80% fat extraction respectively). In soy flake milk, less fat was removed as the % solid increases regardless of the processing method. In whole soybean milk, the fat was removed less efficiently at lower solids level milk using the commercial dairy skimmer and more efficient at lower solids level using the centrifuge-decant method. Based on the Hunter L, a, b measurement, the color of the reduced fat soy flake milk yielded a darker, greener and less yellow colored milk than whole soymilk (α < 0.05), whereas no differences were noticed in reduced fat soybean milk (α < 0.05). Color comparison of whole and skim cow's milk showed the same the same trend as in the soymilk.