Comparative Demonstration of Active and Semi-Passive In Situ Bioremediation Approaches for Perchlorate Impacted Groundwater: Active In Situ Bioremediation Demonstration

Science.gov (United States)

2013-04-01

http://www.itrcweb.org/Documents/PERC-1.pdf • ITRC Perchlorate Team. 2008. Remediation Technologies for Perchlorate Contamination in Water and Soil ...pdf • Solutions EIS. 2006. Protocol for Enhanced In Situ Bioremediation Using Emulsified Vegetable Oil . Prepared for ESTCP. May 2006. • http...Air Force. 2007. Protocol for In Situ Bioremediation of Chlorinated Solvents Using Edible Oil . Prepared for AFCEC - Environmental Science Division

In-situ bioremediation of TCE-contaminated groundwater

Energy Technology Data Exchange (ETDEWEB)

Travis, B.J. [Los Alamos National Lab., NM (United States); Rosenberg, N.D. [Lawrence Livermore National Lab., CA (United States)

1998-12-31

This is the final report of a two-year, Laboratory Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). A barrier to wider use of in situ bioremediation technology is that results are often variable and difficult to predict. In situ bioremediation has shown some very notable and well publicized successes, but implementation of the technology is complex. An incomplete understanding of the effects of variable site characteristics and the lack of adequate tools to predict and measure success have made the design, control and validation of bioremediation more empirical than desired. The long-term objective of this project is to improve computational tools used to assess and optimize the expected performance of bioremediation at a site. An important component of the approach is the explicit inclusion of uncertainties and their effect on the end result. The authors have extended their biokinetics model to include microbial competition and predation processes. Predator species can feed on the microbial species that degrade contaminants, and the simulation studies show that species interactions must be considered when designing in situ bioremediation systems. In particular, the results for TCE indicate that protozoan grazing could reduce the amount of biodegradation by about 20%. These studies also indicate that the behavior of barrier systems can become complex due to predator grazing.

Reduction and immobilization of uranium in the subsurface: controls, mechanisms, and implications for in situ bioremediation

Energy Technology Data Exchange (ETDEWEB)

Stylo, M. A.

2015-07-01

Decades of uranium (U) mining, milling and military use left a legacy of U contamination around the world. The radioactivity and chemical toxicity of U at contaminated sites pose an acute and long-term hazard to human health and the surrounding environment. In order to diminish the risk, in situ bioremediation methods, which contribute to contaminant immobilization, are proposed. Nevertheless, the reported prevalent formation of labile and non-crystalline U(IV) species as a result of microbial U(VI) reduction, in contrast to more stable and crystalline uraninite, undermines the effectiveness of the applied bioremediation. Therefore, a holistic understanding of the controls and mechanisms that govern the formation of non-crystalline U(IV) in the environment is at the core of this thesis. Presence of common groundwater solutes (sulfate, silicate and phosphate) were shown to induce the production of bacterial extracellular polymeric substances (biofilm matrix components), which in turn increases the formation of non-crystalline U(IV) as a result of microbial U reduction. In contrast, a field study suggested that non-crystalline U(IV) was a product of abiotic U reduction followed by the sequestration of U(IV) ions by the biofilm matrix. Those contrasting theories, motivated us to look for an indicator capable of differentiating between biotic and abiotic U reduction in the environment. Uranium isotope fractionation proved to be an excellent tool. Based on our results, the isotopic signature of biotic U reduction (accumulation of {sup 238}U in the reduced phase) is easily distinguishable from the abiotic U reduction signature (either no isotopic fractionation or fractionation in the opposite direction). When contrasted with U isotope signatures recorded in the sediments, the findings of this study indicated that biological activity contributed to the formation of many ancient and modern U(IV) deposits. Equipped with a tool capable of assessing the origin of the U

Reduction and immobilization of uranium in the subsurface: controls, mechanisms, and implications for in situ bioremediation

International Nuclear Information System (INIS)

Stylo, M. A.

2015-01-01

Decades of uranium (U) mining, milling and military use left a legacy of U contamination around the world. The radioactivity and chemical toxicity of U at contaminated sites pose an acute and long-term hazard to human health and the surrounding environment. In order to diminish the risk, in situ bioremediation methods, which contribute to contaminant immobilization, are proposed. Nevertheless, the reported prevalent formation of labile and non-crystalline U(IV) species as a result of microbial U(VI) reduction, in contrast to more stable and crystalline uraninite, undermines the effectiveness of the applied bioremediation. Therefore, a holistic understanding of the controls and mechanisms that govern the formation of non-crystalline U(IV) in the environment is at the core of this thesis. Presence of common groundwater solutes (sulfate, silicate and phosphate) were shown to induce the production of bacterial extracellular polymeric substances (biofilm matrix components), which in turn increases the formation of non-crystalline U(IV) as a result of microbial U reduction. In contrast, a field study suggested that non-crystalline U(IV) was a product of abiotic U reduction followed by the sequestration of U(IV) ions by the biofilm matrix. Those contrasting theories, motivated us to look for an indicator capable of differentiating between biotic and abiotic U reduction in the environment. Uranium isotope fractionation proved to be an excellent tool. Based on our results, the isotopic signature of biotic U reduction (accumulation of 238 U in the reduced phase) is easily distinguishable from the abiotic U reduction signature (either no isotopic fractionation or fractionation in the opposite direction). When contrasted with U isotope signatures recorded in the sediments, the findings of this study indicated that biological activity contributed to the formation of many ancient and modern U(IV) deposits. Equipped with a tool capable of assessing the origin of the U(IV) product

In-Situ Bioremediation of Perchlorate in Groundwater and Soil

OpenAIRE

Jin, Liyan

2012-01-01

Historical, uncontrolled disposal practices have made perchlorate a significant threat to drinking water supplies in the United States. In-situ bioremediation (ISB) technologies are cost effective and provide an environmental friendly solution for treating contaminated groundwater and soil. In situ bioremediation was considered as an option for treatment of perchlorate in groundwater and soil in Lockheed Martin Corporation's Beaumont Site 2 (Beaumont, CA). Based on the perchlorate distribu...

Influence of heterogeneous ammonium availability on bacterial community structure and the expression of nitrogen fixation and ammonium transporter genes during in situ bioremediation of uranium-contaminated groundwater

Energy Technology Data Exchange (ETDEWEB)

Mouser, P.J.; N' Guessan, A.L.; Elifantz, H.; Holmes, D.E.; Williams, K.H.; Wilkins, M.J.; Long, P.E.; Lovley, D.R.

2009-04-01

The impact of ammonium availability on microbial community structure and the physiological status and activity of Geobacter species during in situ bioremediation of uranium-contaminated groundwater was evaluated. Ammonium concentrations varied by as much as two orders of magnitude (<4 to 400 {micro}M) across the study site. Analysis of 16S rRNA gene sequences suggested that ammonium influenced the composition of the microbial community prior to acetate addition with Rhodoferax species predominating over Geobacter species at the site with the highest ammonium, and Dechloromonas species dominating at sites with lowest ammonium. However, once acetate was added, and dissimilatory metal reduction was stimulated, Geobacter species became the predominant organisms at all locations. Rates of U(VI) reduction appeared to be more related to the concentration of acetate that was delivered to each location rather than the amount of ammonium available in the groundwater. In situ mRNA transcript abundance of the nitrogen fixation gene, nifD, and the ammonium importer gene, amtB, in Geobacter species indicated that ammonium was the primary source of nitrogen during in situ uranium reduction, and that the abundance of amtB transcripts was inversely correlated to ammonium levels across all sites examined. These results suggest that nifD and amtB expression by subsurface Geobacter species are closely regulated in response to ammonium availability to ensure an adequate supply of nitrogen while conserving cell resources. Thus, quantifying nifD and amtB expression appears to be a useful approach for monitoring the nitrogen-related physiological status of Geobacter species in subsurface environments during bioremediation. This study also emphasizes the need for more detailed analysis of geochemical/physiological interactions at the field scale, in order to adequately model subsurface microbial processes.

In-situ bioremediation at the French Limited Site

International Nuclear Information System (INIS)

Woodward, R.; Ramsden, D.

1990-01-01

In situ biodegradation of petrochemical wastes at the French Limited Superfund Site was stimulated by providing the appropriate pH, essential nutrients, oxygen, and substrate availability. Fourteen wastewater treatment parameters, plus toxicity, were monitored to document the program of bioremediation. Periodic, organic priority pollutant analysis of mixed liquor, settled sludges and subsoils provided data for kinetics interpretation and half life calculation. The half lives of thirteen PAH compounds ranged from 27 to 46 days, in contrast to the degradation rate, in months, reported for these compounds in LTUs. An ambitious air monitoring program measured fugitive emissions at lagoon side, fenceline, and from the lagoon surface by floating flux chamber. The amount of volatiles lost never exceeded 1/2 of the OSHA 8 hr TLV and it could be readily managed by adjusting the intensity and frequency of mixing and aeration. The demonstration confirmed the feasibility of in situ bioremediation and led to one of the first US EPA Record of Decisions to use bioremediation for cleanup of a large Superfund site. A consent Decree outlining the site remedial action program was signed by the PRP task group and published in the Federal Register. This represents a landmark project for in situ bioremediation and has established precedence for use of this technology at CERCLA and RCRA sites nationwide

Biotransformations Involved in Sustained Reductive Removal of Uranium in Contaminated Aquifers. Final report

International Nuclear Information System (INIS)

Lovley, Derek R.

2008-01-01

The studies completed under this grant significantly advanced the understanding and design of strategies for in situ uranium bioremediation. Novel strategies identified show promise to make in situ uranium bioremediation technically simpler and less expensive. As detailed, important findings included: (1) Development of an electron donor delivery strategy to prolong the in situ activity of Geobacter species and enhance the removal of uranium from the groundwater; (2) Demonstration that reproducible year-to-year field experiments were possible at the ERSP study site in Rifle, CO, making hypothesis-driven field experimentation possible; (3) Elucidation of the geochemical and microbiological heterogeneities with the subsurface during in situ uranium bioremediation, which must be accounted for to accurately model the bioremediation process; (4) The discovery that most of the U(VI) contamination at the Rifle site is sediment-associated rather than mobile in the groundwater, as previously considered; (5) The finding that unlike soluble U(VI), sediment-associated U(VI) is not microbially reducible; (6) The demonstration that electrodes may be an effective alternative to acetate as an electron donor to promote microbial U(VI) reduction in the subsurface with the added benefit that electrode-promoted microbial U(VI) reduction offers the possibility of removing the immobilized uranium from the subsurface; and (7) The finding that, after extended acetate inputs, U(VI) continues to be removed from groundwater long after the introduction of acetate into the subsurface is terminated and that this appears to be due to adsorption onto biomass. This potentially will make in situ uranium bioremediation much less expensive than previously envisioned.

Biotransformation involved in sustained reductive removal of uranium in contaminant aquifers

International Nuclear Information System (INIS)

Lovley, Derek R.

2005-01-01

This report summarizes progress made from August 2004 to July 2005. During this period research focused primarily on obtaining a better understanding of the factors controlling the reduction of U(VI) during in situ uranium bioremediation as well as investigating the potential for using electrodes as an alternative electron donor to promote in situ uranium reduction. Analysis of the 2003 experiment at the field study site in Rifle, CO was completed. The results demonstrated the substantial heterogeneity of the zone undergoing bioremediation, both in terms of geochemistry and microbiology. The lack of U(VI) reduction under sulfate-reducing conditions was clearly documented. The need for more detailed sampling both with time and with depth in the aquifer was demonstrated. For the first time a comparison between the composition of the microbial community in the sediments and the microbes in the corresponding groundwater was attempted. The findings from this study are important not only in further demonstrating the potential for in situ uranium bioremediation, but also for indicating how methods and sampling approaches should be improved in the future. A manuscript summarizing these findings has been accepted for publication in Applied and Environmental Microbiology. In summer of 2004 a new field experiment was conducted at the Rifle site. A novel feature of this study was much more intensive sampling in order to better define the progression of microbial processes during in situ uranium bioremediation. The results demonstrated that stimulation of in situ uranium bioremediation with added acetate was a repeatable phenomenon and that U(VI) reduction was clearly linked to the presence and activity of microorganisms in the family Geobacteraceae. A manuscript summarizing these results is in preparation. A surprising result of the field studies at the Rifle site was that although Geobacter species actively reduced U(VI) in the groundwater, removing it from solution, a high

Cost effectiveness of in situ bioremediation at Savannah River

International Nuclear Information System (INIS)

Saaty, R.P.; Showalter, W.E.; Booth, S.R.

1995-01-01

In situ bioremediation (ISBR) is an innovative new remediation technology for the removal of chlorinated solvents from contaminated soils and groundwater. The principal contaminant at the Savannah River Integrated Demonstration is tricloroethylene (TCE) a volatile organic compound (VOC). A 384-day test run at Savannah River, sponsored by the US Department of Energy (DOE), Office of Technology Development (EM-50), furnished information about the performance and applications of ISBR. In situ bioremediation, as tested, is based on two distinct processes occurring simultaneously; the physical process of in situ air stripping and the biological process of bioremediation. Both processes have the potential to remediate some amount of contamination. A quantity of VOCs, directly measured from the extracted airstream, was removed from the test area by the physical process of air stripping. The biological process is difficult to examine. However, the results of several tests performed at the SRID and independent numerical modeling determined that the biological process remediated an additional 40% above the physical process. Given these data, the cost effectiveness of this new technology can be evaluated

IPCS: An integrated process control system for enhanced in-situ bioremediation

International Nuclear Information System (INIS)

Huang, Y.F.; Wang, G.Q.; Huang, G.H.; Xiao, H.N.; Chakma, A.

2008-01-01

To date, there has been little or no research related to process control of subsurface remediation systems. In this study, a framework to develop an integrated process control system for improving remediation efficiencies and reducing operating costs was proposed based on physical and numerical models, stepwise cluster analysis, non-linear optimization and artificial neural networks. Process control for enhanced in-situ bioremediation was accomplished through incorporating the developed forecasters and optimizers with methods of genetic algorithm and neural networks modeling. Application of the proposed approach to a bioremediation process in a pilot-scale system indicated that it was effective in dynamic optimization and real-time process control of the sophisticated bioremediation systems. - A framework of process control system was developed to improve in-situ bioremediation efficiencies and reducing operating costs

The role indigenous bacterial isolates for bioremediation agent in the uranium contaminated aquatic environment

International Nuclear Information System (INIS)

Mochd Yazid

2014-01-01

A Research on the role of indigenous bacterial isolates for bio-remediation agent of the uranium contaminated in the aquatic environment has been conducted. The objective of the research is to study the role of Pseudomonas sp and Bacillus sp. have been isolated from low level uranium waste for bioremediation agent in their environment, such as the determination of efficiency of the uranium binding compared by the non indigenous bacterial, location of these binding and the influences of added acethyl acid stimulant. The uranium reduction studied was measured by weighting bacterial biomass and uranium concentration was measured by spectrophotometer. The acethyl acid stimulant addition has been done with the variation of concentration and volume. The efficiency of the uranium reduction by indigenous bacterial isolate such as Pseudomonas sp were 84.99 % and Bacillus sp were 52.70 %, so the reduction efficiency by non indigenous bacterial such as Pseudomonas aerogenes were 78.47 % and Bacillus subtilis were 45.22 % for 54 hours incubation time. The result of this research can be concluded that Pseudomonas sp and Bacillus sp. Indigenous bacterial have been isolates from the liquid uranium waste can contributed in bioremediation agent for uranium radionuclide in the environment for 60 ppm concentration with reduction efficiency 52.70 %-84.99 %, that is higher non indigenous bacterial for 54 hours incubation time, the stimulant addition of acethyl acid, the efficiency can be increased up to 99.8 %. (author)

Modeling In Situ Bioremediation of Perchlorate-Contaminated Groundwater

National Research Council Canada - National Science Library

Secody, Roland E

2007-01-01

.... An innovative technology was recently developed which uses dual-screened treatment wells to mix an electron donor into perchlorate-contaminated groundwater in order to effect in situ bioremediation...

Groundbreaking technology: in-situ anaerobic bioremediation for treatment of contaminated soil and groundwater

International Nuclear Information System (INIS)

Fernandes, K.A.

2002-01-01

Anaerobic in-situ bioremediation is a technique often used to cleanse contaminated soil and groundwater. 'Anaerobic in-situ bioremediation' is a phrase with distinct terms all having relevance in the application of this technique. Anaerobic implies the absence of dissolved oxygen, while 'in-situ' simply means that the environmental cleansing occurs with out removing, displacing, or significantly disturbing the specimen or surrounding area. 'Bioremediation' is a term used to describe the biological use of microbes or plants to detoxify the environment. In order to properly implement this complex process, one must have an understanding of microbiology, biochemistry, genetics, metabolic processes, and structure and function of natural microbial communities. (author)

Mineral transformation and biomass accumulation associated with uranium bioremediation at Rifle, Colorado.

Science.gov (United States)

Li, Li; Steefel, Carl I; Williams, Kenneth H; Wilkins, Michael J; Hubbard, Susan S

2009-07-15

Injection of organic carbon into the subsurface as an electron donor for bioremediation of redox-sensitive contaminants like uranium often leads to mineral transformation and biomass accumulation, both of which can alter the flow field and potentially bioremediation efficacy. This work combines reactive transport modeling with a column experiment and field measurements to understand the biogeochemical processes and to quantify the biomass and mineral transformation/accumulation during a bioremediation experiment at a uranium contaminated site near Rifle, Colorado. We use the reactive transport model CrunchFlow to explicitly simulate microbial community dynamics of iron and sulfate reducers, and their impacts on reaction rates. The column experiment shows clear evidence of mineral precipitation, primarily in the form of calcite and iron monosulfide. At the field scale, reactive transport simulations suggest that the biogeochemical reactions occur mostly close to the injection wells where acetate concentrations are highest, with mineral precipitate and biomass accumulation reaching as high as 1.5% of the pore space. This work shows that reactive transport modeling coupled with field data can bean effective tool for quantitative estimation of mineral transformation and biomass accumulation, thus improving the design of bioremediation strategies.

Engineered and subsequent intrinsic in situ bioremediation of a diesel fuel contaminated aquifer

Science.gov (United States)

Hunkeler, Daniel; Höhener, Patrick; Zeyer, Josef

2002-12-01

A diesel fuel contaminated aquifer in Menziken, Switzerland was treated for 4.5 years by injecting aerated groundwater, supplemented with KNO 3 and NH 4H 2PO 4 to stimulate indigenous populations of petroleum hydrocarbon (PHC) degrading microorganisms. After dissolved PHC concentrations had stabilized at a low level, engineered in situ bioremediation was terminated. The main objective of this study was to evaluate the efficacy of intrinsic in situ bioremediation as a follow-up measure to remove PHC remaining in the aquifer after terminating engineered in situ bioremediation. In the first 7 months of intrinsic in situ bioremediation, redox conditions in the source area became more reducing as indicated by lower concentrations of SO 42- and higher concentrations of Fe(II) and CH 4. In the core of the source area, strongly reducing conditions prevailed during the remaining study period (3 years) and dissolved PHC concentrations were higher than during engineered in situ bioremediation. This suggests that biodegradation in the core zone was limited by the availability of oxidants. In lateral zones of the source area, however, gradually more oxidized conditions were reestablished again, suggesting that PHC availability increasingly limited biodegradation. The total DIC production rate in the aquifer decreased within 2 years to about 25% of that during engineered in situ bioremediation and remained at that level. Stable carbon isotope analysis confirmed that the produced DIC mainly originated from PHC mineralization. The total rate of DIC and CH 4 production in the source area was more than 300 times larger than the rate of PHC elution. This indicates that biodegradation coupled to consumption of naturally occurring oxidants was an important process for removal of PHC which remained in the aquifer after terminating engineered measures.

Enhanced ex-situ bioremediation of soil contaminated with ...

African Journals Online (AJOL)

contaminated soil. Thus, the objective of this study was to investigate the feasibility and effectiveness of using electrical biostimulation processes to enhance ex-situ bioremediation of soils contaminated with organic pollutants. The effect of ...

In situ bioremediation under high saline conditions

International Nuclear Information System (INIS)

Bosshard, B.; Raumin, J.; Saurohan, B.

1995-01-01

An in situ bioremediation treatability study is in progress at the Salton Sea Test Base (SSTB) under the NAVY CLEAN 2 contract. The site is located in the vicinity of the Salon Sea with expected groundwater saline levels of up to 50,000 ppm. The site is contaminated with diesel, gasoline and fuel oils. The treatability study is assessing the use of indigenous heterotrophic bacteria to remediate petroleum hydrocarbons. Low levels of significant macro nutrients indicate that nutrient addition of metabolic nitrogen and Orthophosphate are necessary to promote the process, requiring unique nutrient addition schemes. Groundwater major ion chemistry indicates that precipitation of calcium phosphorus compounds may be stimulated by air-sparging operations and nutrient addition, which has mandated the remedial system to include pneumatic fracturing as an option. This presentation is tailored at an introductory level to in situ bioremediation technologies, with some emphasize on innovations in sparge air delivery, dissolved oxygen uptake rates, nutrient delivery, and pneumatic fracturing that should keep the expert's interest

Pilot-scale feasibility of petroleum hydrocarbon-contaminated soil in situ bioremediation

International Nuclear Information System (INIS)

Walker, J.F. Jr.; Walker, A.B.

1995-01-01

An environmental project was conducted to evaluate in situ bioremediation of petroleum hydrocarbon-contaminated soils on Kwajalein Island, a US Army Kwajalein Atoll base in the Republic of the Marshall Islands. Results of laboratory column studies determined that nutrient loadings stimulated biodegradation rates and that bioremediation of hydrocarbon-contaminated soils at Kwajalein was possible using indigenous microbes. The column studies were followed by an ∼10-month on-site demonstration at Kwajalein to further evaluate in situ bioremediation and to determine design and operating conditions necessary to optimize the process. The demonstration site contained low levels of total petroleum hydrocarbons (diesel fuel) in the soil near the ground surface, with concentrations increasing to ∼10,000 mg/kg in the soil near the groundwater. The demonstration utilized 12 in situ plots to evaluate the effects of various combinations of water, air, and nutrient additions on both the microbial population and the hydrocarbon concentration within the treatment plots as a function of depth from the ground surface

Performance parameters for ex situ bioremediation systems

International Nuclear Information System (INIS)

Wade, D.R.

1994-01-01

The potential of biotechnology to reduce the concentration of undesirable hydrocarbons, i.e. gasoline and diesel fuel pollution, is very attractive due to its apparent benign nature and potentially low cost. When good industrial practices are used in the design, construction, and administration of the bioremediation system, the performance of the technology can be predicted and monitored. Some of the principles behind the design, construction, and operation of ex situ bioremediation systems and facilities are described. Biological considerations include creation of a favorable environment for hydrocarbon degrading bacteria in the soils, selection of bacteria, and bacterial byproducts. Chemical considerations include nutrient augmentation, oxygen availability, and the use of surfactants and dispersants. Physical considerations include soil textures and structures, soil temperatures, moisture content, and the use of bulking agents. Experience has shown that indigenous microbes will usually be sufficient to implement bioremediation of petroleum hydrocarbons if encouraged through the application of fertilizers. The introduction of additional carbon sources may be considered if rapid bioremediation rates are desired or if soil conditions are poor. Adjustments to a bioremediation system may be made to enhance the performance of the bacterial community by introducing bulking agents and external temperature sources. Surfactants may be helpful in promoting bacteria-hydrocarbon contact and may be particularly useful for mobilization of free-phase hydrocarbons. 7 refs

Numerical simulations in support of the in situ bioremediation demonstration at Savannah River

International Nuclear Information System (INIS)

Travis, B.J.; Rosenberg, N.D.

1994-06-01

This report assesses the performance of the in situ bioremediation technology demonstrated at the Savannah River Integrated Demonstration (SRID) site in 1992--1993. The goal of the technology demonstration was to stimulate naturally occurring methanotrophic bacteria at the SRID site with injection of methane, air and air-phase nutrients (nitrogen and phosphate) such that significant amounts of the chlorinated solvent present in the subsurface would be degraded. Our approach is based on site-specific numerical simulations using the TRAMP computer code. In this report, we discuss the interactions among the physical and biochemical processes involved in in situ bioremediation. We also investigate improvements to technology performance, make predictions regarding the performance of this technology over long periods of time and at different sites, and compare in situ bioremediation with other remediation technologies

In Situ Bioremediation of 1,4-Dioxane by Methane Oxidizing Bacteria in Coupled Anaerobic-Aerobic Zones

Science.gov (United States)

2016-02-11

FINAL REPORT In Situ Bioremediation of 1,4-Dioxane by Methane Oxidizing Bacteria in Coupled Anaerobic-Aerobic Zones SERDP Project ER-2306...volatile organic compound (CVOCs), ethene and ethane in groundwater at Raritan Arsenal Area 18C after in situ bioremediation . 4 List of...aquifers, the bioremediation approach most commonly used for chlorinated solvents. The ability of methanotrophs to biodegrade 1,4-dioxane was

In situ bioremediation using horizontal wells. Innovative technology summary report

International Nuclear Information System (INIS)

1995-04-01

In Situ Bioremediation (ISB) is the term used in this report for Gaseous Nutrient Injection for In Situ Bioremediation. This process (ISB) involves injection of air and nutrients (sparging and biostimulation) into the ground water and vacuum extraction to remove Volatile Organic Compounds (VOCs) from the vadose zone concomitant with biodegradation of the VOCs. This process is effective for remediation of soils and ground water contaminated with VOCs both above and below the water table. A full-scale demonstration of ISB was conducted as part of the Savannah River Integrated Demonstration: VOCs in Soils and Ground Water at Nonarid Sites. This demonstration was performed at the Savannah River Site from February 1992 to April 1993

In situ bioremediation of chlorinated solvent with natural gas

International Nuclear Information System (INIS)

Rabold, D.E.

1996-01-01

A bioremediation system for the removal of chlorinated solvents from ground water and sediments is described. The system involves the the in-situ injection of natural gas (as a microbial nutrient) through an innovative configuration of horizontal wells

An integrated numerical and physical modeling system for an enhanced in situ bioremediation process

International Nuclear Information System (INIS)

Huang, Y.F.; Huang, G.H.; Wang, G.Q.; Lin, Q.G.; Chakma, A.

2006-01-01

Groundwater contamination due to releases of petroleum products is a major environmental concern in many urban districts and industrial zones. Over the past years, a few studies were undertaken to address in situ bioremediation processes coupled with contaminant transport in two- or three-dimensional domains. However, they were concentrated on natural attenuation processes for petroleum contaminants or enhanced in situ bioremediation processes in laboratory columns. In this study, an integrated numerical and physical modeling system is developed for simulating an enhanced in situ biodegradation (EISB) process coupled with three-dimensional multiphase multicomponent flow and transport simulation in a multi-dimensional pilot-scale physical model. The designed pilot-scale physical model is effective in tackling natural attenuation and EISB processes for site remediation. The simulation results demonstrate that the developed system is effective in modeling the EISB process, and can thus be used for investigating the effects of various uncertainties. - An integrated modeling system was developed to enhance in situ bioremediation processes

BIOREMEDIATION OF CONTAMINATED WASTE BY CADMIUM (Cd IN WATERS USING INDIGEN BACTERIUM WITH EX-SITU WAY

Directory of Open Access Journals (Sweden)

Titik Wijayanti

2017-10-01

Full Text Available The bioremediation technique for a contaminated liquid waste of heavy metals using indigenous bacteria is a convenient alternative to steps continues to be developed. The research aims to find out the effectiveness of an indigenous bacterial consortium in bioremediation of contaminated liquid waste by cadmium by ex-situ. Experiments were arranged in RAL made in ex-situ where a liquid waste industry was given five treatments, namely control and four indigenous bacterial consortia (A, D, E, and J obtained from the isolation of bacteria originating from cadmium-contaminated of waste in Pasuruan district. Furthermore conducted observations of BOD5, COD, d.o. and Cd for seven days to find out the effectiveness of bioremediation. The results showed the four indigenous bacteria consortia have the bioremediation ability to reduce levels of cadmium, BOD5, COD, and increasing levels of DO. Indigenous bacterial consortia D has the best ability of liquid industrial waste bioremediation by ex-situ. Indigenous bacterial consortia J has the best of capacity reduction levels of cadmium, then the other of indigenous bacterial consortia.

Inherently safe in situ uranium recovery

Science.gov (United States)

Krumhansl, James L; Brady, Patrick V

2014-04-29

An in situ recovery of uranium operation involves circulating reactive fluids through an underground uranium deposit. These fluids contain chemicals that dissolve the uranium ore. Uranium is recovered from the fluids after they are pumped back to the surface. Chemicals used to accomplish this include complexing agents that are organic, readily degradable, and/or have a predictable lifetime in an aquifer. Efficiency is increased through development of organic agents targeted to complexing tetravalent uranium rather than hexavalent uranium. The operation provides for in situ immobilization of some oxy-anion pollutants under oxidizing conditions as well as reducing conditions. The operation also artificially reestablishes reducing conditions on the aquifer after uranium recovery is completed. With the ability to have the impacted aquifer reliably remediated, the uranium recovery operation can be considered inherently safe.

ENGINEERING ISSUE: IN SITU BIOREMEDIATION OF CONTAMINATED UNSATURATED SUBSURFACE SOILS

Science.gov (United States)

An emerging technology for the remediation of unsaturated subsurface soils involves the use of microorganisms to degrade contaminants which are present in such soils. Understanding the processes which drive in situ bioremediation, as well as the effectiveness and efficiency of th...

Process, engineering and design aspects of contaminated soil bioremediation. Pt. 1 In situ treatments

International Nuclear Information System (INIS)

De Fraja Frangipane, E.; Andreottola, G.; Tatano, F.

1995-01-01

The present paper is an up-to-date overview of contaminated soil bioremediation techniques, which are analyzed in detail with regard to main process, engineering and design aspects. General biochemical/kinetic aspects of bioremediation of contaminated soil, and in situ treatments, are discussed in this part one

The Study of Isolated Bacteria Application for Bioremediation Agent of Uranium Radionuclide in the Environment

International Nuclear Information System (INIS)

Yazid, Mochd

2007-01-01

Application of the isolated bacteria on the Low Level Uranium Waste as uranium bioremediation agent in the environment has been studied. The objective of this research is to study the possibility of isolated bacteria to be used on uranium remediation process. The isolation of uranium resistance bacteria was carried out on the selective medium SBS containing 10 mg/l uranium, incubated at 37°C until the growth was visible. Selection of binding uranium bacteria was carried out based on their ability to grow on liquid medium containing various concentration of uranium that shacked on 120 rpm speed. The isolated bacteria with the highest specific growth rate constant (μ) were selected for biochemical characterization and identification by matching profile method. The result of this research showed that three selected isolate bacteria were able to grow well on liquid SBS medium until 100 mg/l uranium concentration. The identification results showed that two of them were suspected belong to the genus Pseudomonas and one isolates belong to the genus of Bacillus. The uranium reduction studied was performed by growing up the isolated bacteria on the SBS liquid medium that containing 40 mg/l uranium. Bacterial growth were measured by weighted of bacterial biomass and uranium concentration were measured by spectrophotometer. The research result showed that the selected isolates bacteria may applicable for bioremediation agent because of their ability to grow well on liquid SBS medium and their ability on uranium concentration reduction. The efficiency of reduction by Pseudomonas in the isolated bacteria one were 78.51 % and in the isolated bacteria three were 91.47 % , and Bacillus in the isolate bacteria six were 52.73%. (author)

Key Factors Controlling the Applicability and Efficiency of Bioremediation of Chlorinated Ethenes In Situ

Science.gov (United States)

Zhang, M.; Yoshikawa, M.; Takeuchi, M.; Komai, T.

2012-12-01

Bioremediation has been considered as one of environmentally friendly and cost effective approaches for cleaning up the sites polluted by organic contaminants, such as chlorinated ethenes. Although bioremediation, in its widest sense, is not new, and many researches have been performed on bioremediation of different kinds of pollutants, an effective design and implication of in situ bioremediation still remains a challenging problem because of the complexity. Many factors may affect the applicability and efficiency of bioremediation of chlorinated ethenes in situ, which include the type and concentration of contaminants, biological, geological and hydro-geological conditions of the site, physical and chemical characteristics of groundwater and soils to be treated, as well as the constraints in engineering. In this presentation, an overview together with a detailed discussion on each factor will be provided. The influences of individual factors are discussed using the data obtained or cited from different sites and experiments, and thus under different environmental conditions. The results of this study illustrated that 1) the establishment of microbial consortium is of crucial importance for a complete degradation of chlorinated ethenes, 2) in situ control of favorable conditions for increasing microbial activities for bio-degradation through a designed pathway is the key to success, 3) the focus of a successful remediation system is to design an effective delivery process that is capable of producing adequate amendment mixing of contaminant-degrading bacteria, appropriate concentrations of electron acceptors, electron donors, and microbial nutrients in the subsurface treatment area.

In situ bioremediation of Hanford groundwater

International Nuclear Information System (INIS)

Skeen, R.S.; Roberson, K.R.; Workman, D.J.; Petersen, J.N.; Shouche, M.

1992-04-01

Liquid wastes containing radioactive, hazardous, and regulated chemicals have been generated throughout the 40+ years of operations at the US Department of Energy's (DOE) Hanford Site. Some of these wastes were discharged to the soil column and many of the waste components, including nitrate, carbon tetrachloride (CCl 4 ), and several radionuclides, have been detected in the Hanford groundwater. Current DOE policy prohibits the disposal of contaminated liquids directly to the environment, and remediation of existing contaminated groundwaters may be required. In situ bioremediation is one technology currently being developed at Hanford to meet the need for cost effective technologies to clean groundwater contaminated with CCl 4 , nitrate, and other organic and inorganic contaminants. This paper focuses on the latest results of an on going effort to develop effective in situ remediation strategies through the use of predictive simulations

Molecular analysis of phosphate limitation in Geobacteraceae during the bioremediation of a uranium-contaminated aquifer

Energy Technology Data Exchange (ETDEWEB)

N' Guessan, L.A.; Elifantz, H.; Nevin, K.P.; Mouser, P.J.; Methe, B.; Woodard, T. L.; Manley, K.; Williams, K. H.; Wilkins, M. J.; Larsen, J.T.; Long, P. E.; Lovley, D. R.

2009-09-01

Nutrient limitation is an environmental stress that may reduce the effectiveness of bioremediation strategies, especially when the contaminants are organic compounds or when organic compounds are added to promote microbial activities such as metal reduction. Genes indicative of phosphate-limitation were identified via microarray analysis of chemostat cultures of Geobacter sulfureducens. This analysis revealed that genes in the pst-pho operon, which is associated with a high affinity phosphate uptake system in other microorganisms, had significantly higher transcript abundance under phosphate-limiting conditions, with the genes pstB and phoU the most up-regulated. Quantitative PCR analysis of pstB and phoU transcript levels in G. sulfurreducens grown in chemostats demonstrated that the expression of these genes increased when phosphate was removed from the culture medium. Transcripts of pstB and phoU within the subsurface Geobacter species predominating during an in situ uranium bioremediation field experiment were more abundant than in chemostat cultures of G. sulfurreducens that were not limited for phosphate. Addition of phosphate to incubations of subsurface sediments did not stimulate dissimilatory metal reduction. The added phosphate was rapidly adsorbed onto the sediments. The results demonstrate that Geobacter species can effectively reduce U(VI) even when experiencing suboptimal phosphate concentrations and that increasing phosphate availability with phosphate additions is difficult to achieve due to the high reactivity of this compound. This transcript-based approach developed for diagnosing phosphate limitation should be applicable to assessing the potential need for additional phosphate in other bioremediation processes.

Augmented In Situ Subsurface Bioremediation Process™BIO-REM, Inc. - Demonstration Bulletin

Science.gov (United States)

The Augmented In Situ Subsurface Bioremediation Process™ developed by BIO-REM, Inc., uses microaerophilic bacteria and micronutrients (H-10) and surface tension depressants/penetrants for the treatment of hydrocarbon contaminated soils and groundwater. The bacteria utilize hydroc...

Synchrotron X-ray characterization of mackinawite and uraninite relevant to bio-remediation of groundwater contaminated with uranium

Science.gov (United States)

Carpenter, J.; Hyun, S.; Hayes, K. F.

2010-12-01

Uranium (U) originating from mining operations for weapon manufacturing and nuclear energy production is a significant radionuclide contaminant in groundwater local to uranium mining, uranium milling, and uranium mill tailing (UMT) storage sites. In the USA, the Department of Energy (DOE) is currently overseeing approximately 24 Uranium Mill Tailing Remediation Action (UMTRA) sites which have collectively processed over 27 million tons of uranium ore1,2. In-Situ microbial bio-reduction of the highly mobile U6+ ion into the dramatically less mobile U4+ ion has been demonstrated as an effective remedial process to inhibit uranium migration in the aqueous phase3. The resistance of this process to oxidization and possible remobilization of U when bioremediation stops (and oxidants such as oxygen from the air or nitrate in water diffuse into the formation) in the long term is not known. UMTRA site studies3 have shown that iron sulfide solids are produced by sulfate reducing bacteria (SRB) during U bioremediation, and some forms of these iron sulfide solids are known to be effective oxidant scavengers, potentially protecting against re-oxidation and thus remobilization of U. This work is investigating the role of iron sulfide solids in the long-term immobilization of reduced U compounds after bioremediation is completed in groundwater local to UMTRA sites. Re-oxidation tests are being performed in packed media columns loaded with both FeS and U solids. High quality mackinawite (FeS), and uraninite (UO2) have been synthesized in our laboratory via a wet chemistry approach. These synthetic materials are expected to mimic the naturally occurring and biogenic materials present in biologically stimulated UMTRA sites. In order to establish the initial conditions of the prepared experimental columns and to compare synthetic and biogenic FeS and UO2, these synthesized materials have been characterized with synchrotron radiation at the Stanford Synchrotron Radiation Lightsource

Biosurfactants during in situ bioremediation: factors that influence the production and challenges in evalution.

Science.gov (United States)

Decesaro, Andressa; Machado, Thaís Strieder; Cappellaro, Ângela Carolina; Reinehr, Christian Oliveira; Thomé, Antônio; Colla, Luciane Maria

2017-09-01

Research on the influence of biosurfactants on the efficiency of in situ bioremediation of contaminated soil is continuously growing. Despite the constant progress in understanding the mechanisms involved in the effects of biosurfactants, there are still many factors that are not sufficiently elucidated. There is a lack of research on autochthonous or exogenous microbial metabolism when biostimulation or bioaugmentation is carried out to produce biosurfactants at contaminated sites. In addition, studies on the application of techniques that measure the biosurfactants produced in situ are needed. This is important because, although the positive influence of biosurfactants is often reported, there are also studies where no effect or negative effects have been observed. This review aimed to examine some studies on factors that can improve the production of biosurfactants in soils during in situ bioremediation. Moreover, this work reviews the methodologies that can be used for measuring the production of these biocomposts. We reviewed studies on the potential of biosurfactants to improve the bioremediation of hydrocarbons, as well as the limitations of methods for the production of these biomolecules by microorganisms in soil.

In situ closed-loop bioremediation: Rapid closure in a northern climate

International Nuclear Information System (INIS)

Weymann, D.F.; Hammerbeck, L.M.

1995-01-01

In situ closed-loop bioremediation was employed to achieve site closure at a former railyard in Minneapolis, Minnesota. Soil and groundwater were contaminated with gasoline. The closed-loop remediation system design incorporated three downgradient groundwater recovery wells and a low-pressure pipe infiltration gallery. Aboveground treatment of recovered groundwater was provided by a fixed-film bioreactor. The total reported benzene, toluene, ethylbenzene, and xylenes (BTEX)-removal efficiency of the bioreactor ranged from 98.8% to 100%. Concentrations of BTEX components in groundwater wells were reduced by 45% to 98%. The cleanup goals set by the Minnesota Pollution Control Agency were met within the first 6 months of treatment, and the remediation system was shut down after 20 months of operation. This project further demonstrates the effectiveness of reactor-based, closed-loop in situ bioremediation at sites with favorable conditions

In Situ Bioremediation of Chlorinated Ethenes in Hydraulically-Tight Sediments: Challenges and Limitations

Science.gov (United States)

Zhang, M.; Yoshikawa, M.; Takeuchi, M.; Komai, T.

2011-12-01

Chlorinated ethenes, like perchloroethene (PCE) and trichloroethene (TCE), have been widely used by many industries, especially in developed countries like Japan. Because of their wide applications, lack of proper regulation, poor handing, storage and disposal practices in the past, chlorinated ethenes have become a type of the most prevalent contaminants for soils and groundwater pollution. For the sake of their degradability, bioremediation has been considered as a potentially cost-effective and environmentally friendly approach for cleanup of chlorinated ethenes in situ. In this presentation, we briefly overview the status of soil and groundwater pollution, the recent amendment of the Soil Contamination Countermeasures Act in Japan, comparison between the bioremediation and other techniques like pump and treat, and the mechanisms of reductive dechlorination, direct oxidation and co-metabolism of chlorinated ethenes. We then introduce and discuss some recent challenges and advancements in in-situ bioremediation including technologies for accelerating bio-degradation of chlorinated ethenes, technologies for assessing diffusive properties of dissolved hydrogen in hydraulically-tight soil samples, and combination of bioremediation with other techniques like electro-kinetic approach. Limiting factors that may cause incomplete remediation and/or ineffectiveness of bioremediation are examined from biochemical, geochemical and hydro-geological aspects. This study reconfirmed and illustrated that: 1) The key factor for an effective bioremediation is how to disperse a proper accelerating agent throughout the polluted strata, 2) The effective diffusion coefficient of dissolved hydrogen in geologic media is relatively big and is almost independent on their permeability, and 3) To effectively design and perform an accelerated bioremediation, a combination of natural migration with pressurized injection and/or other approaches, like electro-migration, for stimulating mass

BIOREMEDIATION OF CONTAMINATED WASTE BY CADMIUM (Cd) IN WATERS USING INDIGEN BACTERIUM WITH EX-SITU WAY

OpenAIRE

Titik Wijayanti; Dinna Eka Graha Lestari

2017-01-01

The bioremediation technique for a contaminated liquid waste of heavy metals using indigenous bacteria is a convenient alternative to steps continues to be developed. The research aims to find out the effectiveness of an indigenous bacterial consortium in bioremediation of contaminated liquid waste by cadmium by ex-situ. Experiments were arranged in RAL made in ex-situ where a liquid waste industry was given five treatments, namely control and four indigenous bacterial consortia (A, D, E, and...

Ex-situ bioremediation of petroleum contaminated soil

International Nuclear Information System (INIS)

Minier, M.R.

1994-01-01

The use of stress acclimated bacteria and nutrient supplements to enhance the biodegradation of petroleum contaminated soil can be a cost effective and reliable treatment technology to reduce organic contaminant levels to below established by local, state, and federal regulatory clean-up criteria. This paper will summarize the results of a field study in which 12,000 yds 3 of petroleum contaminated soil was successfully treated via ex-situ bioremediation and through management of macro and micronutrient concentrations, as well as, other site specific environmental factors that are essential for optimizing microbial growth

In situ bioremediation: Cost effectiveness of a remediation technology field tested at the Savannah River

International Nuclear Information System (INIS)

Saaty, R.P.; Showalter, W.E.; Booth, S.R.

1995-01-01

In Situ Bioremediation (ISBR) is an innovative new remediation technology for the removal of chlorinated solvents from contaminated soils and groundwater. The principal contaminant at the SRID is the volatile organic compound (VOC), tricloroetylene(TCE). A 384 day test run at Savannah River, sponsored by the US Department of Energy, Office of Technology Development (EM-50), furnished information about the performance and applications of ISBR. In Situ Bioremediation, as tested, is based on two distinct processes occurring simultaneously; the physical process of in situ air stripping and the biolgoical process of bioremediation. Both processes have the potential to remediate some amount of contamination. A quantity of VOCs, directly measured from the extracted air stream, was removed from the test area by the physical process of air stripping. The biological process is difficult to examine. However, the results of several tests performed at the SRID and independent numerical modeling determined that the biological process remediated an additional 40% above the physical process. Given this data, the cost effectiveness of this new technology can be evaluated

77 FR 33782 - License Amendment To Construct and Operate New In Situ Leach Uranium Recovery Facility; Uranium...

Science.gov (United States)

2012-06-07

... and Operate New In Situ Leach Uranium Recovery Facility; Uranium One Americas; Ludeman AGENCY: Nuclear... provided the first time that a document is referenced. The Ludeman facility In Situ Leach Uranium Recovery... request to amend Source Material License SUA-1341 to construct and operate a new in situ leach uranium...

Real-Time Speciation of Uranium During Active Bioremediation and U(IV) Reoxidation

International Nuclear Information System (INIS)

Komlos, J.; Mishra, B.; Lanzirotti, A.; Myneni, S.; Jaffe, P.

2008-01-01

The biological reduction of uranium from soluble U(VI) to insoluble U(IV) has shown potential to prevent uranium migration in groundwater. To gain insight into the extent of uranium reduction that can occur during biostimulation and to what degree U(IV) reoxidation will occur under field relevant conditions after biostimulation is terminated, X-ray absorption near edge structure (XANES) spectroscopy was used to monitor: (1) uranium speciation in situ in a flowing column while active reduction was occurring; and (2) in situ postbiostimulation uranium stability and speciation when exposed to incoming oxic water. Results show that after 70 days of bioreduction in a high (30 mM) bicarbonate solution, the majority (>90%) of the uranium in the column was immobilized as U(IV). After acetate addition was terminated and oxic water entered the column, in situ real-time XANES analysis showed that U(IV) reoxidation to U(VI) (and subsequent remobilization) occurred rapidly (on the order of minutes) within the reach of the oxygen front and the spatial and temporal XANES spectra captured during reoxidation allowed for real-time uranium reoxidation rates to be calculated.

In situ groundwater and sediment bioremediation: barriers and perspectives at European contaminated sites.

Science.gov (United States)

Majone, Mauro; Verdini, Roberta; Aulenta, Federico; Rossetti, Simona; Tandoi, Valter; Kalogerakis, Nicolas; Agathos, Spiros; Puig, Sebastià; Zanaroli, Giulio; Fava, Fabio

2015-01-25

This paper contains a critical examination of the current application of environmental biotechnologies in the field of bioremediation of contaminated groundwater and sediments. Based on analysis of conventional technologies applied in several European Countries and in the US, scientific, technical and administrative barriers and constraints which still need to be overcome for an improved exploitation of bioremediation are discussed. From this general survey, it is evident that in situ bioremediation is a highly promising and cost-effective technology for remediation of contaminated soil, groundwater and sediments. The wide metabolic diversity of microorganisms makes it applicable to an ever-increasing number of contaminants and contamination scenarios. On the other hand, in situ bioremediation is highly knowledge-intensive and its application requires a thorough understanding of the geochemistry, hydrogeology, microbiology and ecology of contaminated soils, groundwater and sediments, under both natural and engineered conditions. Hence, its potential still remains partially unexploited, largely because of a lack of general consensus and public concerns regarding the lack of effectiveness and control, poor reliability, and possible occurrence of side effects, for example accumulation of toxic metabolites and pathogens. Basic, applied and pre-normative research are all needed to overcome these barriers and make in situ bioremediation more reliable, robust and acceptable to the public, as well as economically more competitive. Research efforts should not be restricted to a deeper understanding of relevant microbial reactions, but also include their interactions with the large array of other relevant phenomena, as a function of the truly variable site-specific conditions. There is a need for a further development and application of advanced biomolecular tools for site investigation, as well as of advanced metabolic and kinetic modelling tools. These would allow a

J.R. SIMPLOT EX-SITU BIOREMEDIATION TECHNOLOGY FOR TREATMENT OF TNT-CONTAMINATED SOILS - INNOVATIVE TECHNOLOGY EVALUATION REPORT

Science.gov (United States)

This report summarizes the findings of the second evaluation of the J.R. Simplot Ex-situ Bioremediation Technology also known as the Simplot Anaerobic Bioremediation (SABRE™) process. This technology was developed by the J.R. Simplot Company to biologically degrade nitroaromatic...

In situ bio-remediation of contaminated soil in a uranium deposit

International Nuclear Information System (INIS)

Groudev, St.; Spasova, I.; Nicolova, M.; Georgiev, P.

2005-01-01

The uranium deposit Curilo, located in Western Bulgaria, for a long period of time was a site of intensive mining activities including both the open-pit and underground techniques as well as in situ leaching of uranium. The mining operations were ended in 1990 but until now both the surface and ground waters and soils within and near the deposit are heavily polluted with radionuclides (mainly uranium and radium) and heavy metals (mainly copper, zinc and cadmium). Laboratory experiments carried out with soil samples from the deposit revealed that an efficient removal of the above-mentioned contaminants was achieved by their solubilizing and washing the soil profile by means of acidified water solutions. The solubilization was connected with the activity of the indigenous soil microflora, mainly with the activity of some acidophilic chemo-litho-trophic bacteria. It was possible to enhance considerably this activity by suitable changes in the levels of some essential environmental factors such as pH and water, oxygen and nutrient contents in the soil. Such treatment was successfully applied also under real field conditions in the deposit. The effluents from the soil profile during the operation above-mentioned contained the pollutants as well as other heavy metals such as iron and manganese dissolved from the soil in concentrations usually higher than the relevant permissible levels for waters intended for use in the agriculture and/or industry. For that reason, these effluents were efficiently cleaned up by means of a natural wetland located near the treated soil. However, such treatment as any other method for treatment of polluted waters is connected with additional costs which increase the total costs for the soil cleanup. A possible way to avoid or at least largely to facilitate the cleanup of the soil effluents is to apply a biotechnological method in which the soil contaminants solubilized in the upper soil layers (mainly in the horizon A) are transferred into

Technology assessment of in situ uranium mining

International Nuclear Information System (INIS)

Cowan, C.E.

1981-01-01

The objective of the PNL portion of the Technology Assessment project is to provide a description of the current in situ uranium mining technology; to evaluate, based on available data, the environmental impacts and, in a limited fashion, the health effects; and to explore the impediments to development and deployment of the in situ uranium mining technology

Combined in-situ and ex-situ bioremediation of petroleum hydrocarbon contaminated soils by closed-loop soil vapor extraction and air injection

International Nuclear Information System (INIS)

Hu, S.S.; Buckler, M.J.

1993-01-01

Treatment and restoration of petroleum hydrocarbon contaminated soils at a bulk petroleum above-ground storage tank (AST) site in Michigan is being conducted through in-situ and ex-situ closed-loop soil vapor extraction (SVE), soil vapor treatment, and treated air injection (AI) processes. The soil vapor extraction process applies a vacuum through the petroleum hydrocarbon affected soils in the ex-situ bio-remediation pile (bio-pile) and along the perimeter of excavated area (in-situ area) to remove the volatile or light petroleum hydrocarbons. This process also draws ambient air into the ex-situ bio-pile and in-situ vadose zone soil along the perimeter of excavated area to enhance biodegradation of light and heavy petroleum hydrocarbons in the soil. The extracted soil vapor is treated using a custom-designed air bio-remediation filter (bio-filter) to degrade the petroleum hydrocarbon compounds in the soil vapor extraction air streams. The treated air is then injected into a flush grade soil bed in the backfill area to perform final polishing of the air stream, and to form a closed-loop air flow with the soil vapor extraction perforated pipes along the perimeter of the excavated area

Technical and Regulatory Requirements for Enhanced In Situ Bioremediation of Chlorinated Solvents in Groundwater

National Research Council Canada - National Science Library

1998-01-01

Enhanced in situ bioremediation (EISB) of chlorinated solvents in groundwater involves the input of an organic carbon source, nutrients, electron acceptors, and/or microbial cultures to stimulate degradation...

Proteogenomic monitoring of Geobacter physiology during stimulated uranium bioremediation

Energy Technology Data Exchange (ETDEWEB)

Wilkins, M.J.; VerBerkmoes, N.C.; Williams, K.H.; Callister, S.J.; Mouser, P.J.; Elifantz, H.; N' Guessan, A.L.; Thomas, B.C.; Nicora, C.D.; Shah, M.B.; Lipton, M.S.; Lovley, D.R.; Hettich, R.L.; Long, P.E.; Banfield, J.F.; Abraham, P.

2009-08-01

Implementation of uranium bioremediation requires methods for monitoring the membership and activities of the subsurface microbial communities that are responsible for reduction of soluble U(VI) to insoluble U(IV). Here, we report a proteomics-based approach for simultaneously documenting the strain membership and microbial physiology of the dominant Geobacter community members during in situ acetate amendment of the U-contaminated Rifle, CO, aquifer. Three planktonic Geobacter-dominated samples were obtained from two wells down-gradient of acetate addition. Over 2,500 proteins from each of these samples were identified by matching liquid chromatography-tandem mass spectrometry spectra to peptides predicted from seven isolate Geobacter genomes. Genome-specific peptides indicate early proliferation of multiple M21 and Geobacter bemidjiensis-like strains and later possible emergence of M21 and G. bemidjiensis-like strains more closely related to Geobacter lovleyi. Throughout biostimulation, the proteome is dominated by enzymes that convert acetate to acetyl-coenzyme A and pyruvate for central metabolism, while abundant peptides matching tricarboxylic acid cycle proteins and ATP synthase subunits were also detected, indicating the importance of energy generation during the period of rapid growth following the start of biostimulation. Evolving Geobacter strain composition may be linked to changes in protein abundance over the course of biostimulation and may reflect changes in metabolic functioning. Thus, metagenomics-independent community proteogenomics can be used to diagnose the status of the subsurface consortia upon which remediation biotechnology relies.

Inherently safe in situ uranium recovery

International Nuclear Information System (INIS)

Krumhansl, James Lee; Beauheim, Richard Louis; Brady, Patrick Vane; Arnold, Bill Walter; Kanney, Joseph F.; McKenna, Sean Andrew

2009-01-01

Expansion of uranium mining in the United States is a concern to some environmental groups and sovereign Native American Nations. An approach which may alleviate some problems is to develop inherently safe in situ uranium recovery ('ISR') technologies. Current ISR technology relies on chemical extraction of trace levels of uranium from aquifers that, once mined, can still contain dissolved uranium and other trace metals that are a health concern. Existing ISR operations are few in number; however, high uranium prices are driving the industry to consider expanding operations nation-wide. Environmental concerns and enforcement of the new 30 ppb uranium drinking water standard may make opening new mining operations more difficult and costly. Here we propose a technological fix: the development of inherently safe in situ recovery (ISISR) methods. The four central features of an ISISR approach are: (1) New 'green' leachants that break down predictably in the subsurface, leaving uranium, and associated trace metals, in an immobile form; (2) Post-leachant uranium/metals-immobilizing washes that provide a backup decontamination process; (3) An optimized well-field design that increases uranium recovery efficiency and minimizes excursions of contaminated water; and (4) A combined hydrologic/geochemical protocol for designing low-cost post-extraction long-term monitoring. ISISR would bring larger amounts of uranium to the surface, leave fewer toxic metals in the aquifer, and cost less to monitor safely - thus providing a 'win-win-win' solution to all stakeholders.

Process for in-situ leaching of uranium

International Nuclear Information System (INIS)

Espenscheid, W.F.; Yan, F.Y.

1983-01-01

The present invention relates to the recovery of uranium from subterranean ore deposits, and more particularly to an in-situ leaching operation employing an aqueous solution of sulfuric acid and carbon dioxide as the lixiviant. Uranium is solubilized in the lixiviant as it traverses the subterranean uranium deposit. The lixiviant is subsequently recovered and treated to remove the uranium

In-situ bioremediation: Or how to get nutrients to all the contaminated soil

International Nuclear Information System (INIS)

Jackson, D.S.; Scovazzo, P.

1994-01-01

Petroleum contamination is a pervasive environmental problem. Bioremediation is winning favor primarily because the soil may be treated on site and systems can be installed to operate without interfering with facility activities. Although bioremediation has been utilized for many years, its acceptance as a cost-effective approach is only now being realized. KEMRON applied in-situ bioremediation at a retired rail yard which had maintained a diesel locomotive refueling station supplied by two 20,000 gallon above ground storage tanks. Contamination originated from both spillage at the pumps and leaking fuel distribution lines. The contamination spread over a 3 acre area from the surface to a depth of up to 20 feet. Levels of diesel contamination found in the soil ranged from less than a 100 ppm to more than 25,000 ppm. The volume of soil which ultimately required treatment was more than 60,000 cubic yards. Several remedial options were examined including excavation and disposal. Excavation was rejected because it would have been cost prohibitive due to the random distribution of the contaminated soil. In-situ Bioremediation was selected as the only alternative which could successfully treat all the contaminated soils. This paper focuses on how KEMRON solved four major problems which would have prevented a successful remediation project. These problems were: soil compaction, random distribution of contaminated soils, potential free product, and extremely high levels of dissolved iron in the groundwater

In situ vadose zone bioremediation of soil contaminated with nonvolatile hydrocarbons

International Nuclear Information System (INIS)

Hogg, D.S.; Burden, R.J.; Riddell, P.J.

1992-01-01

In situ bioremediation has been successfully carried out on petroleum hydrocarbon-contaminated soil at a decommissioned bulk storage terminal in New Zealand. The site soils were contaminated mainly with diesel fuel and spent oil at concentrations ranging up to 95,000 mg/kg of total recoverable petroleum hydrocarbons. The in situ remediation system combines an enhanced bioremediation with vapor extraction and is installed almost entirely below grade, thereby allowing above ground activities to continue unimpeded. Laboratory-scale feasibility testing indicated that although appreciable volatilization of low molecular weight components would occur initially, biodegradation would be the primary mechanism by which contaminated soil would be remediated. During the remedial design phase, preliminary field testing was conducted to evaluate the optimum spacing for extraction wells and inlet vents. A pilot-scale system was installed in a 15-m by 35-m area of the site in June 1989 and operated for approximately 1 year. Soil monitoring performed approximately every 3 months indicated an overall reduction in soil petroleum hydrocarbon concentrations of 87% for the period from June 1989 to May 1991

Hydrodynamics of foam flows for in situ bioremediation of DNAPL-contaminated subsurface

International Nuclear Information System (INIS)

Bouillard, J.X.; Enzien, M.; Peters, R.W.; Frank, J.; Botto, R.E.; Cody, G.

1995-01-01

In situ remediation technologies such as (1) pump-and-treat, (2) soil vacuum extraction, (3) soil flushing/washing, and (4) bioremediation are being promoted for cleanup of contaminated sites. However, these technologies are limited by flow channeling of chemical treatment agents. Argonne National Laboratory (ANL), the Gas Research Institute, and the Institute of Gas Technology are collaboratively investigating a new bioremediation technology using foams. The ability of a foam to block pores and limit flow bypassing makes it ideal for DNAPL remediation. The hydrodynamics of gas/liquid foam flows differ significantly from the hydrodynamics of single and multiphase nonfoaming flows. This is illustrated using a multiphase flow hydrodynamic computer model and a two-dimensional flow visualization cell. A state-of-the-art, nonintrusive, three-dimensional magnetic resonance imaging technique was developed to visualize DNAPL mobilization in three dimensions. Mechanisms to be investigated are in situ DNAPL interactions with the foam, DNAPL emulsification, DNAPL scouring by the foam, and subsequent DNAPL mobilization/redeposition in the porous media

Deploying in situ bioremediation at the Hanford Site

International Nuclear Information System (INIS)

Truex, M.J.; Johnson, C.D.; Newcomer, D.R.; Doremus, L.A.; Hooker, B.S.; Peyton, B.M.; Skeen, R.S.; Chilakapati, A.

1994-11-01

An innovative in-situ bioremediation technology was developed by Pacific Northwest Laboratory (PNL) to destroy nitrate and carbon tetrachloride (CC1 4 ) in the Hanford ground water. The goal of this in-situ treatment process is to stimulate native microorganisms to degrade nitrate and CCl 4 . Nutrient solutions are distributed in the contaminated aquifer to create a biological treatment zone. This technology is being demonstrated at the US Department of Energy's Hanford Site to provide the design, operating, and cost information needed to assess its effectiveness in contaminated ground water. The process design and field operations for demonstration of this technology are influenced by the physical, chemical, and microbiological properties observed at the site. A description of the technology is presented including the well network design, nutrient injection equipment, and means for controlling the hydraulics and microbial reactions of the treatment process

Uranium in situ leach mining in the United States. Information circular

International Nuclear Information System (INIS)

Larson, W.C.

1978-01-01

This report discusses uranium in situ leach mining in the United States; the purpose of which is to acquaint the reader with an overview of this emerging mining technology. This report is not a technical discussion of the subject matter, but rather should be used as a reference source for information on in situ leaching. An in situ leaching bibliography is included as well as engineering data tables for almost all of the active pilot-scale and commercial uranium in situ leaching operators. These tables represent a first attempt at consolidating operational data in one source, on a regional scale. Additional information is given which discusses the current Bureau of Mines uranium in situ leaching research program. Also included is a listing of various State and Federal permitting agencies, and a summary of the current uranium in situ leaching operators. Finally, a glossary of terms has been added, listing some of the more common terms used in uranium in situ leach mining

Multi-Objective Optimization of an In situ Bioremediation Technology to Treat Perchlorate-Contaminated Groundwater

Science.gov (United States)

The presentation shows how a multi-objective optimization method is integrated into a transport simulator (MT3D) for estimating parameters and cost of in-situ bioremediation technology to treat perchlorate-contaminated groundwater.

Evaluation and analysis of geological condition of in-situ fragmentation leaching uranium

International Nuclear Information System (INIS)

Yang Jianming; Tan Kaixuan; Huang Xiaonai

2003-01-01

The ore geological condition, hydrogeological condition, engineering geological condition and technological mineralogical character of in-situ fragmentation leaching uranium are analyzed, and it is considered that the implementation of in-situ fragmentation leaching uranium technology is decided by different geological factor. Previously prospecting and geological condition evaluation of uranium ore is based on traditional mining method. If in-situ fragmentation leaching uranium method is adopted, one must re-evaluate previously prospected deposits before they are mined, or one must evaluate new prospecting deposits according to geological conditions of in-situ fragmentation leaching uranium method. The feasibility evaluation method of uranium deposit by in-situ fragmentation leaching uranium put forward by B. N. Mociniets is introducd, and it is considered that B. N. Mociniets method has guidable significance for geological condition evaluation before uranium deposits are mined. A feasibility study is done by applying B. N. Mociniets method to a uranium deposit. (authors)

In situ leaching of uranium: Technical, environmental and economic aspects

International Nuclear Information System (INIS)

1989-01-01

Within the framework of its activities in nuclear raw materials the International Atomic Energy Agency has convened a series of meetings to discuss various aspects of uranium ore processing technology, recovery of uranium from non-conventional resources and development of projects for the production of uranium concentrates including economic aspects. As part of this continuing effort to discuss and document important aspects of uranium production the IAEA convened a Technical Committee Meeting on Technical, Economic and Environmental Aspects of In-Situ Leaching. Although the use of this technique is limited by geological and economic constraints, it has a significant potential to produce uranium at competitive prices. This is especially important in the current uranium market which is mainly characterised by large inventories, excess production capability and low prices. This situation is not expected to last indefinitely but it is unlikely to change drastically in the next ten years or so. This Technical Committee Meeting was held in Vienna from 3 to 6 November 1987 with the attendance of 24 participants from 12 countries. Eight papers were presented. Technical sessions covered in-situ mining research, environmental and licensing aspects and restoration of leached orebodies; the technological status of in-situ leaching, the current status and future prospects of in-situ leaching of uranium in Member States, general aspects of planning and implementation of in-situ projects and the economics of in-situ leaching. Refs, figs and tabs

IRP, Aerobic Cometabolic In Situ Bioremediation Technology Guidance Manual and Screening Software User's Guide

National Research Council Canada - National Science Library

1998-01-01

...) have been documented. These compounds can pose a serious threat to human health or the environment. Aerobic cometabolic in situ bioremediation is an innovative technology being used for treatment of groundwater contaminated with CAHs, especially TCE...

Bioreduction and immobilization of uranium in situ: a case study at a USA Department of Energy radioactive waste site, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

Wu, Weimin; Carley, Jack M.; Watson, David B.; Gu, Baohua; Brooks, Scott C.; Kelly, Shelly D.; Kemner, Kenneth M.; Van Nostrand, Joy; Wu, Liyou; Zhou, Jizhong; Luo, Jian; Cardenas, Erick; Fields, Matthew Wayne; Marsh, Terence; Tiedje, James; Green, Stefan; Kostka, Joel; Kitanidis, Peter K.; Jardine, Philip; Criddle, Craig

2011-01-01

Bioremediation of uranium contaminated groundwater was tested by delivery of ethanol as an electron donor source to stimulate indigenous microbial bioactivity for reduction and immobilization of uranium in situ, followed by tests of stability of uranium sequestration in the bioreduced area via delivery of dissolved oxygen or nitrate at the US Department of energy's Integrated Field Research Challenge site located at Oak Ridge, Tennessee, USA. After long term treatment that spanned years, uranium in groundwater was reduced from 40-60 mg · L -1 to -1 , below the USA EPA standard for drinking water. The bioreduced uranium was stable under anaerobic or anoxic conditions, but addition of DO and nitrate to the bioreduced zone caused U remobilization. The change in the microbial community and functional microorganisms related to uranium reduction and oxidation were characterized. The delivery of ethanol as electron donor stimulated the activities of indigenous microorganisms for reduction of U(VI) to U(IV). Results indicated that the immobilized U could be partially remobilized by D0 and nitrate via microbial activity. An anoxic environmental condition without nitrate is essential to maintain the stability of bioreduced uranium.

Selection of electron acceptors and strategies for in situ bioremediation

International Nuclear Information System (INIS)

Norris, R.D.

1995-01-01

The most critical aspect of designing in situ bioremediation systems is, typically, the selection and method of delivery of the electron acceptor. Nitrate, sulfate, and several forms of oxygen can be introduced, depending on the contaminants and the site conditions. Oxygen can be added as air, pure oxygen, hydrogen peroxide, or an oxygen release compound. Simplistic cost calculations can illustrate the advantages of some methods over others, providing technical requirements can be met

Laboratory-scale in situ bioremediation in heterogeneous porous media: biokinetics-limited scenario.

Science.gov (United States)

Song, Xin; Hong, Eunyoung; Seagren, Eric A

2014-03-01

Subsurface heterogeneities influence interfacial mass-transfer processes and affect the application of in situ bioremediation by impacting the availability of substrates to the microorganisms. However, for difficult-to-degrade compounds, and/or cases with inhibitory biodegradation conditions, slow biokinetics may also limit the overall bioremediation rate, or be as limiting as mass-transfer processes. In this work, a quantitative framework based on a set of dimensionless coefficients was used to capture the effects of the competing interfacial and biokinetic processes and define the overall rate-limiting process. An integrated numerical modeling and experimental approach was used to evaluate application of the quantitative framework for a scenario in which slow-biokinetics limited the overall bioremediation rate of a polycyclic aromatic hydrocarbon (naphthalene). Numerical modeling was conducted to simulate the groundwater flow and naphthalene transport and verify the system parameters, which were used in the quantitative framework application. The experiments examined the movement and biodegradation of naphthalene in a saturated, heterogeneous intermediate-scale flow cell with two layers of contrasting hydraulic conductivities. These experiments were conducted in two phases: Phase I, simulating an inhibited slow biodegradation; and Phase II, simulating an engineered bioremediation, with system perturbations selected to enhance the slow biodegradation rate. In Phase II, two engineered perturbations to the system were selected to examine their ability to enhance in situ biodegradation. In the first perturbation, nitrogen and phosphorus in excess of the required stoichiometric amounts were spiked into the influent solution to mimic a common remedial action taken in the field. The results showed that this perturbation had a moderate positive impact, consistent with slow biokinetics being the overall rate-limiting process. However, the second perturbation, which was to

In situ leaching of uranium

International Nuclear Information System (INIS)

Martin, B.

1980-01-01

A process is described for the in-situ leaching of uranium-containing ores employing an acidic leach liquor containing peroxymonosulphuric acid. Preferably, additionally, sulphuric acid is present in the leach liquor. (author)

In situ bioremediation for the Hanford carbon tetrachloride plume. Innovative technology summary report

International Nuclear Information System (INIS)

1999-04-01

The 200 Area at Hanford (also called the Central Plateau) contains approximately 817 waste sites, 44 facilities to be demolished, and billions of gallons of contaminated groundwater resulting from chemical processing plants and associated waste facilities (e.g., waste tanks). From 1955 to 1973, carbon tetrachloride, nitrate, and other materials were discharged to subsurface liquid waste disposal facilities in the 200 Area. As much as 600,000 kilograms of carbon tetrachloride may have entered the soil column and a portion of this has contaminated the underlying aquifer. In Situ Bioremediation for the Hanford Carbon Tetrachloride Plume (ISB), which is the term used in this report for an in situ treatment process using indigenous micro-organisms with a computer based Accelerated Bioremediation Design Tool (ABDT), remediates groundwater contaminated with volatile organic compounds (VOCs) and nitrates under anaerobic conditions. ISB involves the injection of nutrients into the groundwater and subsequent extraction and re-injection of the groundwater to provide nutrient distribution in the aquifer

Testing of in situ and ex situ bioremediation approaches for an oil-contaminated peat bog following a pipeline break

International Nuclear Information System (INIS)

Wilson, J.J.; Lee, D.W.; Yeske, B.M.; Kuipers, F.

2000-01-01

The feasibility of treating a 1985 pipeline spill of light Pembina Cardium crude oil at a bog near Violet Grove, Alberta was discussed. Pembina Pipeline Corporation arranged for a treatability test to be conducted on oil-contaminated sphagnum peat moss from the site to determine effective in situ or ex situ remediation options for the site. The test was used to evaluate the biodegradation potential of contaminants. Four tests were designed to simulate field different field treatment approaches and to collect critical data on toxicity and leachability of the peat moss. The tests included a bioslurry test, a soil microcosm test, an aerated water saturated peat column test, and a standard toxicity characteristic leachate potential test. The first three tests gave similar results of at least 74 per cent biodegradation of the residual crude oil on the peat solids and no residual toxicity as measured by the Microtox Assay. It was determined that both in situ bioremediation using an aerated water injection system or an ex situ landfarming approach would achieve required criteria and no fertilizers would be necessary to maintain active bioremediation. The new gas-liquid reactor (GLR) aeration technology used in these tests creates a constant supply of hyperoxygenated water prior to column injection. The continuous release of tiny air bubbles maximizes air surface area and increases the gas transfer rates. 3 tabs., 3 figs

Current status and prospects of uranium geology developments of foreign in-situ leachable sandstone type uranium deposits

International Nuclear Information System (INIS)

Wang Zhengbang

2002-01-01

Firstly, with emphasis on in-situ leachable sandstone-type uranium deposits, the prospecting history of uranium deposits worldwide and its scientific research development are generally reviewed in four steps, and their basic historical experience is also summarized. Secondly, based on the detailed description of current development status of uranium geology of foreign in-situ leachable sandstone-type uranium deposits the important strategic position of sandstone-type uranium deposits in overall uranium resources all-over-the-world and its classification, spatial-temporal distribution and regulation, and metallogenic condition of sandstone-type uranium deposits are analysed thoroughly in five aspects: techtonics, paleo-climate, hydrogeology, sedimentary facies and lithology, as well as uranium sources: Afterwards, evaluation principles of three type of hyper-genic, epigenetic infiltrated sandstone-type uranium deposits are summarized. Based on sandstone-type uranium deposits located two important countries: the United States and Russia, the current development status of prospecting technology for in-situ leachable sandstone-type uranium deposits in foreign countries is outlined. Finally, according to the prospects of supply-demand development of global uranium resources, the author points out seriously that Chinese uranium geology is faced with a severe challenge, and proposes directly four strategic measures that should be taken

In situ bioremediation strategies for oiled shoreline environments

International Nuclear Information System (INIS)

Lee, K.; Mora, S. de

1999-01-01

Despite advances in preventative measures, recent events have demonstrated that accidental oil spills at sea will still occur. While physical (e.g. booms and skimmers) and chemical (e.g. chemical dispersants) methods have been developed to recover and/or disperse oil spilled at sea, they are not 100% effective and are frequently limited by operational constraints attributed to sea state and/or nature of the contamination. As a result, oil spills frequently impact shoreline environments. In situ bioremediation, the addition of substances or modification of habitat at contaminated sites to accelerate natural biodegradation processes, is now recognised as an alternative spill response technology of the remediation of these sites. Recommended for use following the physical removal of bulk oil, this treatment strategy has an operational advantage in that it breaks down and/or removes the residual contamination in place. Laboratory experiments and field trials have demonstrated the feasibility and success of bioremediation strategies such as nutrient enrichment to enhance bacterial degradation of oil on cobble, sand beach and salt marsh environments. With improved knowledge of the factors that limit natural oil degradation rates, the feasibility of other strategies such as phytoremediation, enhanced oil-mineral fines interaction and the addition of oxygen or alternative electron acceptors are now being evaluated. Laboratory and field test protocols are being refined for the selection of effective bioremediation agents and methods of application. It is recommended that future operational guidelines include real time product efficacy test and environmental effects monitoring programs. Termination of treatment should be implemented when: 1) it is no longer effective; 2) the oil has degraded to acceptable biologically benign concentrations; or 3) toxicity due to the treatment is increasing. (Author)

In situ remediation of uranium contaminated groundwater

International Nuclear Information System (INIS)

Dwyer, B.P.; Marozas, D.C.

1997-01-01

In an effort to develop cost-efficient techniques for remediating uranium contaminated groundwater at DOE Uranium Mill Tailing Remedial Action (UMTRA) sites nationwide, Sandia National Laboratories (SNL) deployed a pilot scale research project at an UMTRA site in Durango, CO. Implementation included design, construction, and subsequent monitoring of an in situ passive reactive barrier to remove Uranium from the tailings pile effluent. A reactive subsurface barrier is produced by emplacing a reactant material (in this experiment various forms of metallic iron) in the flow path of the contaminated groundwater. Conceptually the iron media reduces and/or adsorbs uranium in situ to acceptable regulatory levels. In addition, other metals such as Se, Mo, and As have been removed by the reductive/adsorptive process. The primary objective of the experiment was to eliminate the need for surface treatment of tailing pile effluent. Experimental design, and laboratory and field results are discussed with regard to other potential contaminated groundwater treatment applications

Feasibility testing of in situ vitrification of uranium-contaminated soils

International Nuclear Information System (INIS)

Ikuse, H.; Tsuchino, S.; Tasaka, H.; Timmerman, C.L.

1989-01-01

Process feasibility studies using in situ vitrification (ISV) were successfully performed on two different uranium-contaminated wastes. In situ vitrification is a thermal treatment process that converts contaminated soils into durable glass and crystalline form. Of the two different wastes, one waste was uranium mill tailings, while the other was uranium-contaminated soils which had high water contents. Analyses of the data from the two tests are presented

Ex-situ bioremediation of U(VI from contaminated mine water using Acidithiobacillus ferrooxidans strains

Directory of Open Access Journals (Sweden)

Maria eRomero-Gonzalez

2016-05-01

Full Text Available The ex-situ bioremoval of U(VI from contaminated water using Acidithiobacillus ferrooxidans strain 8455 and 13538 was studied under a range of pH and uranium concentrations. The effect of pH on the growth of bacteria was evaluated across the range 1.5 – 4.5 pH units. The respiration rate of At. ferrooxidans at different U(VI concentrations was quantified as a measure of the rate of metabolic activity over time using an oxygen electrode. The biosorption process was quantified using a uranyl nitrate solution, U-spiked growth media and U-contaminated mine water. The results showed that both strains of At. ferrooxidans are able to remove U(VI from solution at pH 2.5 – 4.5, exhibiting a buffering capacity at pH 3.5. The respiration rate of the micro-organism was affected at U(VI concentration of 30 mg L-1. The kinetics of the sorption fitted a pseudo-first order equation, and depended on the concentration of U(VI. The KD obtained from the biosorption experiments indicated that strain 8455 is more efficient for the removal of U(VI. A bioreactor designed to treat a solution of 100 mg U(VI L-1 removed at least 50% of the U(VI in water. The study demonstrated that At. ferrooxidans can be used for the ex-situ bioremediation of U(VI contaminated mine water.

Ex situ bioremediation of oil-contaminated soil.

Science.gov (United States)

Lin, Ta-Chen; Pan, Po-Tsen; Cheng, Sheng-Shung

2010-04-15

An innovative bioprocess method, Systematic Environmental Molecular Bioremediation Technology (SEMBT) that combines bioaugmentation and biostimulation with a molecular monitoring microarray biochip, was developed as an integrated bioremediation technology to treat S- and T-series biopiles by using the landfarming operation and reseeding process to enhance the bioremediation efficiency. After 28 days of the bioremediation process, diesel oil (TPH(C10-C28)) and fuel oil (TPH(C10-C40)) were degraded up to approximately 70% and 63% respectively in the S-series biopiles. When the bioaugmentation and biostimulation were applied in the beginning of bioremediation, the microbial concentration increased from approximately 10(5) to 10(6) CFU/g dry soil along with the TPH biodegradation. Analysis of microbial diversity in the contaminated soils by microarray biochips revealed that Acinetobacter sp. and Pseudomonas aeruginosa were the predominant groups in indigenous consortia, while the augmented consortia were Gordonia alkanivorans and Rhodococcus erythropolis in both series of biopiles during bioremediation. Microbial respiration as influenced by the microbial activity reflected directly the active microbial population and indirectly the biodegradation of TPH. Field experimental results showed that the residual TPH concentration in the complex biopile was reduced to less than 500 mg TPH/kg dry soil. The above results demonstrated that the SEMBT technology is a feasible alternative to bioremediate the oil-contaminated soil. Crown Copyright 2009. Published by Elsevier B.V. All rights reserved.

Preliminary discussion on uranium metallogenic models of China's in-situ leachable sandstone-type uranium deposits

International Nuclear Information System (INIS)

Zhang Jindai; Xu Gaozhong; Chen Anping; Wang Cheng

2005-01-01

By comprehensively analyzing metallogenic environments and main ore-controlling factors of important uranium metallogenic regions of in-situ leachable sandstone-type uranium deposits at the southern margin of Yili basin, at the south-western margin of Turpan-Hami basin and in the northeastern Ordos basin, the authors of this paper discuss the metallogenic models of China's in-situ leachable sandstone-type uranium deposits, and suggest that the interlayer oxidation zone type uranium deposits in Yili and Turpan-Hami basins are basically controlled by favourable structures, sedimentary formations and interlayer oxidation zone, and are characterized by multistage uranium concentration, namely the uranium pre-concentration of ore-hosting sedimentary formation, the uranium ore-formation in the stage of supergenic epigenetic reworking, and the further superimposition enrichment of post-ore tectonic activity. However, the interlayer oxidation zone type uranium deposit in the northeastern Ordos was formed after the formation of the secondary reduction. So, paleo-interlayer oxidation zone type uranium mineralization has the mineralization size much greater than the former two. (authors)

Field Implementation Plan for the In-Situ Bioremediation Treatability Study at the Technical Area-V Groundwater Area of Concern

Energy Technology Data Exchange (ETDEWEB)

Li, Jun [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2016-10-31

This Field Implementation Plan (FIP) was prepared by Sandia National Laboratories, New Mexico (SNL/NM) and provides instruction on conducting a series of in-situ bioremediation (ISB) tests as described in the Revised Treatability Study Work Plan for In-Situ Bioremediation at the Technical Area-V Groundwater Area of Concern, referred to as the Revised Work Plan in this FIP. The Treatability Study is designed to gravity inject an electron-donor substrate and bioaugmentation bacteria into groundwater via three injection wells to perform bioremediation of the constituents of concern (COCs), nitrate and trichloroethene (TCE), in the regions with the highest concentrations at the Technical Area-V Groundwater (TAVG) Area of Concern (AOC). The Treatability Study will evaluate the effectiveness of bioremediation solution delivery and COC treatment over time. This FIP is designed for SNL/NM work planning and management. It is not intended to be submitted for regulator’s approval. The technical details presented in this FIP are subject to change based on field conditions, availability of equipment and materials, feasibility, and inputs from Sandia personnel and Aboveground Injection System contractor.

Field Implementation Plan for the In-Situ Bioremediation Treatability Study at the Technical Area-V Groundwater Area of Concern

International Nuclear Information System (INIS)

Li, Jun

2016-01-01

This Field Implementation Plan (FIP) was prepared by Sandia National Laboratories, New Mexico (SNL/NM) and provides instruction on conducting a series of in-situ bioremediation (ISB) tests as described in the Revised Treatability Study Work Plan for In-Situ Bioremediation at the Technical Area-V Groundwater Area of Concern, referred to as the Revised Work Plan in this FIP. The Treatability Study is designed to gravity inject an electron-donor substrate and bioaugmentation bacteria into groundwater via three injection wells to perform bioremediation of the constituents of concern (COCs), nitrate and trichloroethene (TCE), in the regions with the highest concentrations at the Technical Area-V Groundwater (TAVG) Area of Concern (AOC). The Treatability Study will evaluate the effectiveness of bioremediation solution delivery and COC treatment over time. This FIP is designed for SNL/NM work planning and management. It is not intended to be submitted for regulator's approval. The technical details presented in this FIP are subject to change based on field conditions, availability of equipment and materials, feasibility, and inputs from Sandia personnel and Aboveground Injection System contractor.

Uranium in situ leaching: its advantages, practice, problems and computer simulation

International Nuclear Information System (INIS)

Hancock, B.A.

1977-01-01

In situ leaching for the recovery of uranium from low grade sandstone deposits is one of the newest technological advances in the mineral industry. It is rapidly developing into a commercially feasible mining system which has economic, environmental, and social advantages over conventional mining systems. Because of the current uranium shortage, development of in situ leaching into a sophisticated system has gained new impetus. In situ leaching will become an important mining technique in the future, which will greatly help to supply uranium for the United States' energy needs. In this paper, the author gives an overview of the merits of the system, as well as the technology problems, and research in solution mining of uranium. 17 references

Process for the in-situ leaching of uranium

International Nuclear Information System (INIS)

Habib, E.T.; Vogt, T.C.

1982-01-01

Process for the in-situ leaching of uranium employing an alkaline lixiviant and an alkali metal or alkaline earth metal hypochlorite as an oxidizing agent. The use of the hypochlorite oxidant results in significantly higher uranium recoveries and leaching rates than those attained by the use of conventional oxidants. The invention is particularly suitable for use in subterranean deposits in which the uranium mineral is associated with carbonaceous material which retards access to the uranium by the lixiviant

Optimal design of an in-situ bioremediation system using support vector machine and particle swarm optimization

Science.gov (United States)

ch, Sudheer; Kumar, Deepak; Prasad, Ram Kailash; Mathur, Shashi

2013-08-01

A methodology based on support vector machine and particle swarm optimization techniques (SVM-PSO) was used in this study to determine an optimal pumping rate and well location to achieve an optimal cost of an in-situ bioremediation system. In the first stage of the two stage methodology suggested for optimal in-situ bioremediation design, the optimal number of wells and their locations was determined from preselected candidate well locations. The pumping rate and well location in the first stage were subsequently optimized in the second stage of the methodology. The highly nonlinear system of equations governing in-situ bioremediation comprises the equations of flow and solute transport coupled with relevant biodegradation kinetics. A finite difference model was developed to simulate the process of in-situ bioremediation using an Alternate-Direction Implicit technique. This developed model (BIOFDM) yields the spatial and temporal distribution of contaminant concentration for predefined initial and boundary conditions. BIOFDM was later validated by comparing the simulated results with those obtained using BIOPLUME III for the case study of Shieh and Peralta (2005). The results were found to be in close agreement. Moreover, since the solution of the highly nonlinear equation otherwise requires significant computational effort, the computational burden in this study was managed within a practical time frame by replacing the BIOFDM model with a trained SVM model. Support Vector Machine which generates fast solutions in real time was considered to be a universal function approximator in the study. Apart from reducing the computational burden, this technique generates a set of near optimal solutions (instead of a single optimal solution) and creates a re-usable data base that could be used to address many other management problems. Besides this, the search for an optimal pumping pattern was directed by a simple PSO technique and a penalty parameter approach was adopted

Optimal design of an in-situ bioremediation system using support vector machine and particle swarm optimization.

Science.gov (United States)

ch, Sudheer; Kumar, Deepak; Prasad, Ram Kailash; Mathur, Shashi

2013-08-01

A methodology based on support vector machine and particle swarm optimization techniques (SVM-PSO) was used in this study to determine an optimal pumping rate and well location to achieve an optimal cost of an in-situ bioremediation system. In the first stage of the two stage methodology suggested for optimal in-situ bioremediation design, the optimal number of wells and their locations was determined from preselected candidate well locations. The pumping rate and well location in the first stage were subsequently optimized in the second stage of the methodology. The highly nonlinear system of equations governing in-situ bioremediation comprises the equations of flow and solute transport coupled with relevant biodegradation kinetics. A finite difference model was developed to simulate the process of in-situ bioremediation using an Alternate-Direction Implicit technique. This developed model (BIOFDM) yields the spatial and temporal distribution of contaminant concentration for predefined initial and boundary conditions. BIOFDM was later validated by comparing the simulated results with those obtained using BIOPLUME III for the case study of Shieh and Peralta (2005). The results were found to be in close agreement. Moreover, since the solution of the highly nonlinear equation otherwise requires significant computational effort, the computational burden in this study was managed within a practical time frame by replacing the BIOFDM model with a trained SVM model. Support Vector Machine which generates fast solutions in real time was considered to be a universal function approximator in the study. Apart from reducing the computational burden, this technique generates a set of near optimal solutions (instead of a single optimal solution) and creates a re-usable data base that could be used to address many other management problems. Besides this, the search for an optimal pumping pattern was directed by a simple PSO technique and a penalty parameter approach was adopted

Test plan for in situ bioremediation demonstration of the Savannah River Integrated Demonstration Project DOE/OTD TTP No.: SR 0566-01. Revision 3

Energy Technology Data Exchange (ETDEWEB)

Hazen, T.C.

1991-09-18

This project is designed to demonstrate in situ bioremediation of groundwater and sediment contaminated with chlorinated solvents. Indigenous microorganisms will be simulated to degrade trichloroethylene (TCE), tetrachloroethylene (PCE) and their daughter products in situ by addition of nutrients to the contaminated zone. in situ biodegradation is a highly attractive technology for remediation because contaminants are destroyed, not simply moved to another location or immobilized, thus decreasing costs, risks, and time, while increasing efficiency and public and regulatory acceptability. Bioremediation has been found to be among the least costly technologies in applications where it will work.

Field-scale evaluation of biological uranium reduction and reoxidation in the near-source zone at the NABIR Field Research Center in Oak Ridge, TN

International Nuclear Information System (INIS)

Craig S. Criddle; Peter Kitanidis; Scott Fendorf; Weimin Wu; Philip M. Jardine; Jizhong Zhou; Baohua Gu

2006-01-01

The primary objective of the project is to advance the understanding and predictive capability of coupled hydrological, geochemical, and microbiological processes that control the in situ transport and bioremediation radionuclides and co-contaminants at multiple scales. Specific objectives include: (1) Investigate the feasibility of in situ bioremediation of uranium in a highly contaminated region within the subsurface of Area 3 of the DoE ERSP FRC (2) Using a variety of tracer strategies, develop and model a system that establishes hydraulic control of the target region for biostimulation (3) Perform long term in situ biostimulation studies that create a microbial communities capable of reducing residual nitrate to N2 and mobile U(VI) to sparingly soluble U(IV) (4) Use a variety of solid and solution phase interrogation techniques to quantify the extent of in situ reduction and immobilization of U(VI). (5) Investigate a variety of geochemical factors that influence the stability and possible reoxidation of reduced uranium

Stakeholder acceptance analysis: In-well vapor stripping, in-situ bioremediation, gas membrane separation system (membrane separation)

International Nuclear Information System (INIS)

Peterson, T.

1995-12-01

This document provides stakeholder evaluations on innovative technologies to be used in the remediation of volatile organic compounds from soils and ground water. The technologies evaluated are; in-well vapor stripping, in-situ bioremediation, and gas membrane separation

Bioremediation of Uranium-Contaminated Groundwater using Engineered Injection and Extraction

Science.gov (United States)

Greene, J. A.; Neupauer, R.; Ye, M.; Kasprzyk, J. R.; Mays, D. C.; Curtis, G. P.

2017-12-01

During in-situ remediation of contaminated groundwater, a treatment chemical is injected into the contaminated groundwater to react with and degrade the contaminant, with reactions occurring where the treatment chemical contacts the contaminant. Traditional in-situ groundwater remediation relies on background groundwater flow for spreading of treatment chemicals into contaminant plumes. Engineered Injection and Extraction (EIE), in which time-varying induced flow fields are used to actively spread the treatment chemical into the contaminant plume, has been developed to increase contact between the contaminant and treatment chemical, thereby enhancing contaminant degradation. EIE has been investigated for contaminants that degrade through irreversible bimolecular reaction with a treatment chemical, but has not been investigated for a contaminant governed by reversible reactions. Uranium primarily occurs in its aqueous, mobile form, U(VI), in the environment but can be bioreduced to its sparingly soluble, immobile form, U(IV), by iron reducing bacteria stimulated by an acetate amendment. In this study, we investigate the ability of EIE to facilitate and sustain favorable conditions to immobilize uranium during remediation, and to prevent re-mobilization of uranium into the aqueous phase after active remediation has ended. Simulations in this investigation are conducted using a semi-synthetic model based on physical and chemical conditions at the Naturita Uranium Mill Tailings Remedial Action (UMTRA) site in southwestern Colorado and the Old Rifle UMTRA site in western Colorado. The EIE design is optimized for the synthetic model using the Borg multi-objective evolutionary algorithm.

Bioremediation of Metals and Radionuclides: What It Is and How It Works (2nd Edition)

Energy Technology Data Exchange (ETDEWEB)

Palmisano, Anna; Hazen, Terry

2003-09-30

This primer is intended for people interested in environmental problems of the U.S. Department of Energy (DOE) and in their potential solutions. It will specifically look at some of the more hazardous metal and radionuclide contaminants found on DOE lands and at the possibilities for using bioremediation technology to clean up these contaminants. The second edition of the primer incorporates recent findings by researchers in DOE's Natural and Accelerated Bioremediation Research (NABIR) Program. Bioremediation is a technology that can be used to reduce, eliminate, or contain hazardous waste. Over the past two decades, it has become widely accepted that microorganisms, and to a lesser extent plants, can transform and degrade many types of contaminants. These transformation and degradation processes vary, depending on the physical-chemical environment, microbial communities, and nature of the contaminant. This technology includes intrinsic bioremediation, which relies on naturally occurring processes, and accelerated bioremediation, which enhances microbial degradation or transformation through the addition of nutrients (biostimulation) or inoculation with microorganisms (bioaugmentation). Over the past few years, interest in bioremediation has increased. It has become clear that many organic contaminants such as hydrocarbon fuels can be degraded to relatively harmless products such as CO{sub 2} (the end result of the degradation process). Waste water managers and scientists have also found that microorganisms can interact with metals and convert them from one chemical form to another. Laboratory tests and ex situ bioremediation applications have shown that microorganisms can change the valence, or oxidation state, of some heavy metals (e.g., chromium and mercury) and radionuclides (e.g., uranium) by using them as electron acceptors. In some cases, the solubility of the altered species decreases and the contaminant is immobilized in situ, i.e., precipitated into

Investigating the biogeochemical interactions involved in simultaneous TCE and Arsenic in situ bioremediation

Science.gov (United States)

Cook, E.; Troyer, E.; Keren, R.; Liu, T.; Alvarez-Cohen, L.

2016-12-01

The in situ bioremediation of contaminated sediment and groundwater is often focused on one toxin, even though many of these sites contain multiple contaminants. This reductionist approach neglects how other toxins may affect the biological and chemical conditions, or vice versa. Therefore, it is of high value to investigate the concurrent bioremediation of multiple contaminants while studying the microbial activities affected by biogeochemical factors. A prevalent example is the bioremediation of arsenic at sites co-contaminated with trichloroethene (TCE). The conditions used to promote a microbial community to dechlorinate TCE often has the adverse effect of inducing the release of previously sequestered arsenic. The overarching goal of our study is to simultaneously evaluate the bioremediation of arsenic and TCE. Although TCE bioremediation is a well-understood process, there is still a lack of thorough understanding of the conditions necessary for effective and stable arsenic bioremediation in the presence of TCE. The objective of this study is to promote bacterial activity that stimulates the precipitation of stable arsenic-bearing minerals while providing anaerobic, non-extreme conditions necessary for TCE dechlorination. To that end, endemic microbial communities were examined under various conditions to attempt successful sequestration of arsenic in addition to complete TCE dechlorination. Tested conditions included variations of substrates, carbon source, arsenate and sulfate concentrations, and the presence or absence of TCE. Initial arsenic-reducing enrichments were unable to achieve TCE dechlorination, probably due to low abundance of dechlorinating bacteria in the culture. However, favorable conditions for arsenic precipitation in the presence of TCE were eventually discovered. This study will contribute to the understanding of the key species in arsenic cycling, how they are affected by various concentrations of TCE, and how they interact with the key

Manual of acid in situ leach uranium mining technology

International Nuclear Information System (INIS)

2001-08-01

In situ leaching (ISL) technology recovers uranium using two alternative chemical leaching systems - acid and alkaline. This report brings together information from several technical disciplines that are an essential part of ISL technology. They include uranium geology, geohydrology, chemistry as well as reservoir engineering and process engineering. This report provides an extensive description of acid ISL uranium mining technology

Manual of acid in situ leach uranium mining technology

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-08-01

In situ leaching (ISL) technology recovers uranium using two alternative chemical leaching systems - acid and alkaline. This report brings together information from several technical disciplines that are an essential part of ISL technology. They include uranium geology, geohydrology, chemistry as well as reservoir engineering and process engineering. This report provides an extensive description of acid ISL uranium mining technology.

An evaluation of in-situ bioremediation processes

International Nuclear Information System (INIS)

Cole, L.L.; Rashidi, M.

1996-08-01

Remediation of petroleum hydrocarbons in groundwater was the primary focus in the initial application of in-situ bioremediation which, from its development in the 1970s, has grown to become one of the most promising technologies for the degradation of a wide variety of organic contaminants. The degradation of contaminants in subsurface soils is the current new focus of the technology. While the need for improvements in the technology does exist, the indisputable fact remains that this technology is by far the least expensive and that it has the capability to provide long term reduced levels of contaminants or long term complete remediation of contaminated sites. The aim of this paper is to disclose pertinent information related to current conditions and current feelings in the area of new research, novel applications, new government regulations, and an overview of new topics on the horizon that relate to the overall technology

An evaluation of in-situ bioremediation processes

Energy Technology Data Exchange (ETDEWEB)

Cole, L.L. [Prairie View A and M Univ., TX (United States); Rashidi, M. [Lawrence Livermore National Lab., CA (United States). Environmental Programs Directorate

1996-08-01

Remediation of petroleum hydrocarbons in groundwater was the primary focus in the initial application of in-situ bioremediation which, from its development in the 1970s, has grown to become one of the most promising technologies for the degradation of a wide variety of organic contaminants. The degradation of contaminants in subsurface soils is the current new focus of the technology. While the need for improvements in the technology does exist, the indisputable fact remains that this technology is by far the least expensive and that it has the capability to provide long term reduced levels of contaminants or long term complete remediation of contaminated sites. The aim of this paper is to disclose pertinent information related to current conditions and current feelings in the area of new research, novel applications, new government regulations, and an overview of new topics on the horizon that relate to the overall technology.

Microbes safely, effectively bioremediate oil field pits

International Nuclear Information System (INIS)

Shaw, B.; Block, C.S.; Mills, C.H.

1995-01-01

Natural and augmented bioremediation provides a safe, environmental, fast, and effective solution for removing hydrocarbon stains from soil. In 1992, Amoco sponsored a study with six bioremediation companies, which evaluated 14 different techniques. From this study, Amoco continued using Environmental Protection Co.'s (EPC) microbes for bioremediating more than 145 sites near Farmington, NM. EPC's microbes proved effective on various types of hydrocarbon molecules found in petroleum stained soils from heavy crude and paraffin to volatiles such as BTEX (benzene, toluene, ethylbenzene, xylene) compounds. Controlled laboratory tests have shown that these microbes can digest the hydrocarbon molecules with or without free oxygen present. It is believed that this adaptation gives these microbes their resilience. The paper describes the bioremediation process, environmental advantages, in situ and ex situ bioremediation, goals of bioremediation, temperature effects, time, cost, and example sites that were treated

Radiological aspects of in situ uranium recovery

International Nuclear Information System (INIS)

BROWN, STEVEN H.

2007-01-01

In the last few years, there has been a significant increase in the demand for Uranium as historical inventories have been consumed and new reactor orders are being placed. Numerous mineralized properties around the world are being evaluated for Uranium recovery and new mining / milling projects are being evaluated and developed. Ore bodies which are considered uneconomical to mine by conventional methods such as tunneling or open pits, can be candidates for non-conventional recovery techniques, involving considerably less capital expenditure. Technologies such as Uranium in situ leaching in situ recovery (ISL / ISR), have enabled commercial scale mining and milling of relatively small ore pockets of lower grade, and may make a significant contribution to overall world wide uranium supplies over the next ten years. Commercial size solution mining production facilities have operated in the US since 1975. Solution mining involves the pumping of groundwater, fortified with oxidizing and complexing agents into an ore body, solubilizing the uranium in situ, and then pumping the solutions to the surface where they are fed to a processing plant. Processing involves ion exchange and may also include precipitation, drying or calcining and packaging operations depending on facility specifics. This paper presents an overview of the ISR process and the health physics monitoring programs developed at a number of commercial scale ISL / ISR Uranium recovery and production facilities as a result of the radiological character of these processes. Although many radiological aspects of the process are similar to that of conventional mills, conventional-type tailings as such are not generated. However, liquid and solid byproduct materials may be generated and impounded. The quantity and radiological character of these by products are related to facility specifics. Some special monitoring considerations are presented which are required due to the manner in which Radon gas is evolved in

Situ leaching uranium mining conditions of the pilot phase of the safety management

International Nuclear Information System (INIS)

Liu Wenyuan

2014-01-01

With China's large, very large sandstone type uranium deposits have been discovered in the Ordos Basin, Inner Mongolia and its surrounding for uranium mining in the region has been carried out. Sandstone-type uranium mining, mainly used in China is 'to dip' and the technology is relatively mature. Situ leaching mining process, the deposit conditions Test conditions pilot phase, however, limited by cost control and field conditions, equipment shabby, out in the conditions of the pilot phase of security issues in the larger securityrisks. This will be Ordos ongoing test conditions situ leaching uranium mines, for example, raised situ leaching uranium mining conditions of the pilot phase a few safety measures recommended. (author)

J.R. SIMPLOT EX-SITU BIOREMEDIATION TECHNOLOGY FOR TREATMENT OF DINOSEB-CONTAMINATED SOILS - INNOVATIVE TECHNOLOGY REPORT

Science.gov (United States)

This report summarizes the findings of an evaluation of the J.R. Simplot Ex-Situ Bioremediation Technology on the degradation of dinoseb (2-set-butyl-4,6-dinitrophenol) an agricultural herbicide. This technology was developed by the J.R. Simplot Company (Simplot) to biologically ...

Natural carriers in bioremediation: A review

Directory of Open Access Journals (Sweden)

Anna Dzionek

2016-09-01

Full Text Available Bioremediation of contaminated groundwater or soil is currently the cheapest and the least harmful method of removing xenobiotics from the environment. Immobilization of microorganisms capable of degrading specific contaminants significantly promotes bioremediation processes, reduces their costs, and also allows for the multiple use of biocatalysts. Among the developed methods of immobilization, adsorption on the surface is the most common method in bioremediation, due to the simplicity of the procedure and its non-toxicity. The choice of carrier is an essential element for successful bioremediation. It is also important to consider the type of process (in situ or ex situ, type of pollution, and properties of immobilized microorganisms. For these reasons, the article summarizes recent scientific reports about the use of natural carriers in bioremediation, including efficiency, the impact of the carrier on microorganisms and contamination, and the nature of the conducted research.

Bioremediation: A natural solution

International Nuclear Information System (INIS)

Hicks, B.N.; Caplan, J.A.

1993-01-01

Bioremediation is an attractive remediation alternative because most full-scale bioremediation projects involve cost-effective contaminant treatment on-site. Recently, large scale bioremediation projects have included cleanups of ocean tanker spills, land-based chemical spills, and leaking chemical and petroleum storage tanks. Contaminated matrices have included beaches, soils, groundwater, surface waters (i.e., pits, ponds, lagoons), process waste streams and grease traps. Bioremediation is especially cost-effective when both soil and groundwater matrices are impacted because one remediation treatment system can be design to treat both media simultaneously in place. The primary advantages of in situ bioremediation include: on-site destruction of contaminants; accelerated cleanup time; minimal disruption to operations; lower remediation costs; and reduction of future liability

Chattanooga shale: uranium recovery by in situ processing

International Nuclear Information System (INIS)

Jackson, D.D.

1977-01-01

The increasing demand for uranium as reactor fuel requires the addition of sizable new domestic reserves. One of the largest potential sources of low-grade uranium ore is the Chattanooga shale--a formation in Tennessee and neighboring states that has not been mined conventionally because it is expensive and environmentally disadvantageous to do so. An in situ process, on the other hand, might be used to extract uranium from this formation without the attendant problems of conventional mining. We have suggested developing such a process, in which fracturing, retorting, and pressure leaching might be used to extract the uranium. The potential advantages of such a process are that capital investment would be reduced, handling and disposing of the ore would be avoided, and leaching reagents would be self-generated from air and water. If successful, the cost reductions from these factors could make the uranium produced competitive with that from other sources, and substantially increase domestic reserves. A technical program to evaluate the processing problems has been outlined and a conceptual model of the extraction process has been developed. Preliminary cost estimates have been made, although it is recognized that their validity depends on how successfully the various processing steps are carried out. In view of the preliminary nature of this survey (and our growing need for uranium), we have urged a more detailed study on the feasibility of in situ methods for extracting uranium from the Chattanooga shale

Bioremediation in Germany: Markets, technologies, and leading companies

International Nuclear Information System (INIS)

Raphael, T.; Glass, D.J.

1995-01-01

Bioremediation has become an internationally accepted remediation tool. Commercial bioremediation activities take place in many European countries, but Germany and the Netherlands are the clear European leaders, with both having a long history of public and private sector activity in biological technologies. The German bioremediation market has been driven by government regulation, in particular the waste laws that apply to contaminated soils. The 1994 German market for bioremediation is estimated at $70 to 100 million (US $). There are at least 150 companies active in bioremediation in Germany, most of which practice bioremediation of hydrocarbon-contaminated soils, either in situ or ex situ. Because of their predominance in the current European market, German firms are well positioned to expand into those nations in the European Union (EU) currently lacking an environmental business infrastructure

PROTOCOL FOR DETERMINING BIOAVAILABILITY AND BIOKINETICS OF ORGANIC POLLUTANTS IN DISPERSED, COMPACTED AND INTACT SOIL SYSTEMS TO ENHANCE IN SITU BIOREMEDIATION

Science.gov (United States)

The development of effective in situ and on-site bioremediation technologies can facilitate the cleanup of chemically-contaminated soil sites. Knowledge of biodegradation kinetics and bioavailability of organic pollutants can facilitate decisions on the efficacy of in situ and o...

The method for the in-situ leaching of a uranium mining

International Nuclear Information System (INIS)

Chen Zhen; Xu Xianyi; Wang Xuemin

2011-01-01

The paper reviews the main factors of in-situ leaching for uranium mining. A kind of technique called dilution with few reagent is put forward to the in-situ leaching of sandstone-type uranium deposit with high TDS. This technique can not only effectively prevent the pipe plug, but also can improve the economic benefits. (authors)

In situ spectroscopy and spectroelectrochemistry of uranium in high-temperature alkali chloride molten salts.

Science.gov (United States)

Polovov, Ilya B; Volkovich, Vladimir A; Charnock, John M; Kralj, Brett; Lewin, Robert G; Kinoshita, Hajime; May, Iain; Sharrad, Clint A

2008-09-01

Soluble uranium chloride species, in the oxidation states of III+, IV+, V+, and VI+, have been chemically generated in high-temperature alkali chloride melts. These reactions were monitored by in situ electronic absorption spectroscopy. In situ X-ray absorption spectroscopy of uranium(VI) in a molten LiCl-KCl eutectic was used to determine the immediate coordination environment about the uranium. The dominant species in the melt was [UO 2Cl 4] (2-). Further analysis of the extended X-ray absorption fine structure data and Raman spectroscopy of the melts quenched back to room temperature indicated the possibility of ordering beyond the first coordination sphere of [UO 2Cl 4] (2-). The electrolytic generation of uranium(III) in a molten LiCl-KCl eutectic was also investigated. Anodic dissolution of uranium metal was found to be more efficient at producing uranium(III) in high-temperature melts than the cathodic reduction of uranium(IV). These high-temperature electrolytic processes were studied by in situ electronic absorption spectroelectrochemistry, and we have also developed in situ X-ray absorption spectroelectrochemistry techniques to probe both the uranium oxidation state and the uranium coordination environment in these melts.

Groundwater restoration with in situ uranium leach mining

International Nuclear Information System (INIS)

Charbeneau, R.J.

1984-01-01

In situ leach mining of uranium has developed into a major mining technology. Since 1975, when the first commercial mine was licensed in the United States, the percentage or uranium produced by in situ mining has steadily grown from 0.6 to 10 percent in 1980. Part of the reason for this growth is that in situ mining offers less initial capital investment, shorter start-up times, greater safety, and less labor than conventional mining methods. There is little disturbance of the surface terrain or surface waters, no mill tailings piles, and no large open pits, but in situ leaching mining does have environmental disadvantages. During the mining, large amounts of ground water are cirulated and there is some withdrawal from an area where aquifers constitute a major portion of the water supply for other purposes. When an ammonia-based leach system is used, the ammonium ion is introduced into an area where cation exchange on clays (and some production of nitrate) may occur. Also, injection of an oxidant with the leach solution causes valence and phase changes of indigenous elements such as As, Cu, Fe, Mo, Se, S, and V as well as U. Furthermore, the surrounding ground water can become contaminated by escape of the leach solution from the mining zone. This chapter presents an overview of the in situ mining technology, including uranium deposition, mining techniques, and ground water restoration alternatives. The latter part of the chapter covers the situation in South Texas. Economics and development of the industry, groundwater resources, regulation, and restoration activities are also reviewed

Bioremediation of oil contaminated soils

International Nuclear Information System (INIS)

Beeson, D.L.; Hogue, J.I.; Peterson, J.C.; Guerra, G.W.

1994-01-01

The Baldwin Waste Oil Site was an abandoned waste oil recycling facility located in Robstown, Nueces County, Texas. As part of their site assessment activities, the US Environmental Protection Agency (EPA) requested that the Ecology and Environment, Inc., Technical Assistance Team (TAT) investigate the feasibility of using in-situ bioremediation to remediate soils contaminated with oil and grease components, petroleum hydrocarbons, and volatile organic compounds. Bioremediation based on the land treatment concept was tested. The land treatment concept uses techniques to optimize indigenous microbial populations and bring them in contact with the contaminants. The study was designed to collect data upon which to base conclusions on the effectiveness of bioremediation, to demonstrate the effectiveness of bioremediation under field conditions, and to identify potential problems in implementing a full-scale project. Bioremediation effectiveness was monitored through total petroleum hydrocarbons (TPH) and Oil and Grease (O and G) analyses. Site specific treatment goals for the pilot project were concentrations of less than 1% for O and G and less than 10,000 mg/kg for TPH. Based on the reduction of TPH and O and G concentrations and the cost effectiveness of bioremediation based on the land treatment concept, full-scale in-situ bioremediation was initiated by the EPA at the Baldwin Waste Oil Site in February of 1993

Technique for in situ leach simulation of uranium ores

International Nuclear Information System (INIS)

Grant, D.C.; Seidel, D.C.; Nichols, I.L.

1985-01-01

In situ uranium mining offers the advantages of minimal environmental disturbance, low capital and operating costs, and reduced mining development time. It is becoming an increasingly attractive mining method for the recovery of uranium from secondary ore deposits. In order to better understand the process, a laboratory technique was developed and used to study and simulate both the chemical and physical phenomena occurring in ore bodies during in situ leaching. The laboratory simulation technique has been used to determine effects of leaching variables on permeability, uranium recovery, and post-leach aquifer restoration. This report describes the simulation system and testing procedure in sufficient detail to allow the construction of the system, and to perform the desired leaching tests. With construction of such a system, in situ leaching of a given ore using various leach conditions can be evaluated relatively rapidly in the laboratory. Not only could optimum leach conditions be selected for existing ore bodies, but also exploitation of new ore bodies could be accelerated. 8 references, 8 figures, 2 tables

Bioremediation/Biorecovery of uranium from aquatic resource/waste: the Cyano-Deino story

International Nuclear Information System (INIS)

Apte, Shree Kumar

2015-01-01

Terrestrial sources of uranium are getting depleted fast and may be exhausted in the next few decades. This has triggered a search for alternate or secondary resources for this precious metal. Nearly 4.5 billion tons of uranium on our planet resides in seawater, albeit at very low concentrations of 3 ppb. Recovering uranium from such low concentrations is a major challenge. Two marine cyanobacteria, the unicellular Synechococcus elongatus and the filamentous Anabaena torulosa, were found to be capable of rapidly sequestering uranyl carbonate (the predominant uranyl species at the sea-water pH of 7.8) from aqueous solutions, including simulated sea-water. While Synechococcus strain adsorbed the metal as carbonato complexes on cell surface ligands, A. torulosa trapped it in novel surface-associated polyphosphate bodies. The uranium binding potential of cyanobacterial biomass was comparable to, if not better than, the currently in use polyamidoxime resin. The bound uranium could be desorbed easily and the biomass reused a few times. The method has eminently higher application potential in uranium-contaminated terrestrial waters, where the metal concentration is several times higher. Low concentrations (<1 to few mM) of uranium are also found in acidic/alkaline nuclear waste and arise from metal extraction or during reprocessing of fuel. Removal of uranium from such solutions is very desirable for safer disposal of such waste. Biological agents to be employed in such situations also need to be tolerant to and stable in high radiation environments, unless dead cells can be used. To address such bioremediation, the extremely radio-resistant microbe Deinococcus radiodurans was genetically engineered to express either a non-specific acid phosphatase PhoN or a highly active novel alkaline phosphatase PhoK. Apart from the need for high expression of desired protein, such engineering is also fraught with problems of stability, localization and activity of the expressed

Ecotoxicological evaluation of in situ bioremediation of soils contaminated by the explosive 2,4,6-trinitrotoluene (TNT)

International Nuclear Information System (INIS)

Frische, Tobias

2003-01-01

The luminescent bacteria assay, using soil leachates, was the most sensitive toxicity indicator. - To evaluate the environmental relevance of in situ bioremediation of contaminated soils, effective and reliable monitoring approaches are of special importance. The presented study was conducted as part of a research project investigating in situ bioremediation of topsoils contaminated by the explosive 2,4,6-trinitrotoluene (TNT). Changes in soil toxicity within different experimental fields at a former ordnance factory were evaluated using a battery of five bioassays (plant growth, Collembola reproduction, soil respiration, luminescent bacteria acute toxicity and mutagenicity test) in combination to chemical contaminant analysis. Resulting data reveal clear differences in sensitivities between methods with the luminescent bacteria assay performed with soil leachates as most sensitive toxicity indicator. Complete test battery results are presented in so-called soil toxicity profiles to visualise and facilitate the interpretation of data. Both biological and chemical monitoring results indicate a reduction of soil toxicity within 17 months of remediation

Bioremediation of oil spills

International Nuclear Information System (INIS)

Foght, J.M.; Westlake, D.W.S.

1992-01-01

In-situ bioremediation of crude oil spills relies on either the indigenous microbes at the polluted site, whose degradative abilities are accelerated by adding such agents as fertilizers or dispersants, or on introducing pollutant-degrading microbes into the site (possibly accompanied by stimulatory chemicals). The bioremediation method to be used at a specific site must be selected to be suitable for that site and its environmental conditions. The basic components of bioremediation are outlined and the background information needed to understand the chemical and biological limitations of the technique are presented. Specifically, the microbial community, the crude oil substrate composition, and biological limiting factors are discussed. Generalized examples of bioremediation applications are illustrated. 10 refs

Solution (in situ leach) mining of uranium: an overview

International Nuclear Information System (INIS)

Kuhaida, A.J. Jr.; Kelly, M.J.

1978-01-01

Increases in the demand for and price of uranium have made in-situ mining an attractive alternative to the open-pit and underground U mining methods. Up to 50% of the known ore-bearing sandstone in the western U.S. can be mined using the in-situ mining method. In-situ mining also offers a significant environmental advantage. Restoration of the contaminated groundwater is discussed

In situ bioremediation (natural attenuation) at a gas plant waste site

International Nuclear Information System (INIS)

Ginn, J.S.; Sims, R.C.

1995-01-01

A former manufactured gas plant (MGP) waste site in New York was evaluated with regard to natural attenuation of polycyclic aromatic hydrocarbons (PAHs). Parent-compound concentrations of PAHs within an aquifer plume were observed to decrease with time subsequent to source removal of coal tar. Biotransformation-potential studies indicated that indigenous microorganisms in soil from the site were capable of degrading naphthalene and phenanthrene. A biochemical metabolite of phenanthrene degradation, 1-hydroxy-2-naphthoic acid (1H2NA), was tentatively characterized in coal-tar-contaminated soil from the site-based on liquid chromatographic retention time. Kinetic information was developed for the disappearance of phenanthrene and 1H2NA in nonspiked contaminated soil at the site. The Microtox trademark bioassay was used to evaluate toxicity trends in contaminated soil at the site. Results from the Microtox trademark indicated a decreasing trend in toxicity with respect to time in contaminated site soil. Research results were evaluated with regard to the National Research Council's guidelines for evaluating in situ bioremediation, and were used to enhance site characterization and monitoring information for evaluating the role of bioremediation as part of natural attenuation of PAHs at coal-tar-contaminated sites

Remediation of soil/concrete contaminated with uranium and radium by biological method

International Nuclear Information System (INIS)

Gye-Nam Kim; Seung-Su Kim; Hye-Min Park; Won-Suk Kim; Uk-Ryang Park; Jei-Kwon Moon

2013-01-01

Biological method was studied for remediation of soil/concrete contaminated with uranium and radium. Optimum experiment conditions for mixing ratios of penatron and soil, and the pH of soil was obtained through several bioremediations with soil contaminated with uranium and radium. It was found that an optimum mixing ratio of penatron for bioremediation of uranium soil was 1 %. Also, the optimum pH condition for bioremediation of soil contaminated with uranium and radium was 7.5. The removal efficiencies of uranium and radium from higher concentration of soil were rather reduced in comparison with those from lower concentration of soil. Meanwhile, the removal of uranium and radium in concrete by bioremediation is possible but the removal rate from concrete was slower than that from soil. The removal efficiencies of uranium and radium from soil under injection of 1 % penatron at pH 7.5 for 120 days were 81.2 and 81.6 %, respectively, and the removal efficiencies of uranium and radium from concrete under the same condition were 63.0 and 45.2 %, respectively. Beyond 30 days, removal rates of uranium and radium from soil and concrete by bioremediation was very slow. (author)

Biological reduction of uranium-From the laboratory to the field

International Nuclear Information System (INIS)

Dullies, Frank; Lutze, Werner; Gong, Weiliang; Nuttall, H. Eric

2010-01-01

The chemical and biological processes underlying in situ bioremediation of uranium-contaminated groundwater have been studied in the laboratory and in the field. This article focuses on the long-term stability of uraninite (UO 2 ) in the underground. A large tailings pond, 'Daenkritz 1' in Germany, was selected for this investigation. A single-pass flow-through experiment was run in a 100-liter column: bioremediation for 1 year followed by infiltration of tap water (2.5 years) saturated with oxygen, sufficient to oxidize the precipitated uraninite in two months. Instead, only 1 wt.% uraninite was released over 2.4 years at concentrations typically less than 20 μg/L. Uraninite was protected against oxidation by the mineral mackinawite (FeS 0.9 ), a considerable amount of which had formed, together with uraninite. A confined field test was conducted adjacent to the tailings pond, which after bio-stimulation showed similarly encouraging results as in the laboratory. Taking Daenkritz 1 as an example we show that in situ bioremediation can be a viable option for long-term site remediation, if the process is designed based on sufficient laboratory and field data. The boundary conditions for the site in Germany are discussed.

A demonstration of in situ bioremediation of CCL4 at the Hanford Site

International Nuclear Information System (INIS)

Hooker, B.S.; Skeen, R.S.; Truex, M.J.; Peyton, B.M.

1994-11-01

The United States Department of Energy's VOC-Arid Integrated Demonstration Program (VOC/Arid-ID) is developing an in situ bioremediation technology to meet the need for a cost-effective method to clean ground water contaminated with chlorinated solvents, nitrates, or other organic and inorganic contaminants. Currently, a field demonstration of the technology is being conducted at the Hanford site in southeastern Washington state. The goal of this demonstration is to stimulate native denitrifying microorganisms to destroy carbon tetrachloride and nitrate. Contaminants are destroyed by mixing an electron donor (acetate) and an electron acceptor (nitrate) into the aquifer, using a matrix of recirculation wells. This work also evaluates the effectiveness.of applying scale-up techniques developed in the petrochemical industry to bioremediation. The scale-up process is based on combining fluid mixing and transport predictions with numerical descriptions for biological transport and reaction kinetics. This paper focuses on the necessity of this design approach to select nutrient feeding strategies that limit biofouling while actively destroying contaminants

Surfactant-aided recovery/in situ bioremediation for oil-contaminated sites

International Nuclear Information System (INIS)

Ducreaux, J.; Baviere, M.; Seabra, P.; Razakarisoa, O.; Shaefer, G.; Arnaud, C.

1995-01-01

Bioremediation has been the most commonly used method way for in situ cleaning of soils contaminated with low-volatility petroleum products such as diesel oil. However, whatever the process (bioventing, bioleaching, etc.), it is a time-consuming technique that may be efficiency limited by both accessibility and too high concentrations of contaminants. A currently developed process aims at quickly recovering part of the residual oil in the vadose and capillary zones by surfactant flushing, then activating in situ biodegradation of the remaining oil in the presence of the same or other surfactants. The process has been tested in laboratory columns and in an experimental pool, located at the Institut Franco-Allemand de Recherche sur l'Environnement (IFARE) in Strasbourg, France. Laboratory column studies were carried out to fit physico-chemical and hydraulic parameters of the process to the field conditions. The possibility of recovering more than 80% of the oil in the flushing step was shown. For the biodegradation step, forced aeration as a mode of oxygen supply, coupled with nutrient injection aided by surfactants, was tested

Management of groundwater in-situ bioremediation system using reactive transport modelling under parametric uncertainty: field scale application

Science.gov (United States)

Verardo, E.; Atteia, O.; Rouvreau, L.

2015-12-01

In-situ bioremediation is a commonly used remediation technology to clean up the subsurface of petroleum-contaminated sites. Forecasting remedial performance (in terms of flux and mass reduction) is a challenge due to uncertainties associated with source properties and the uncertainties associated with contribution and efficiency of concentration reducing mechanisms. In this study, predictive uncertainty analysis of bio-remediation system efficiency is carried out with the null-space Monte Carlo (NSMC) method which combines the calibration solution-space parameters with the ensemble of null-space parameters, creating sets of calibration-constrained parameters for input to follow-on remedial efficiency. The first step in the NSMC methodology for uncertainty analysis is model calibration. The model calibration was conducted by matching simulated BTEX concentration to a total of 48 observations from historical data before implementation of treatment. Two different bio-remediation designs were then implemented in the calibrated model. The first consists in pumping/injection wells and the second in permeable barrier coupled with infiltration across slotted piping. The NSMC method was used to calculate 1000 calibration-constrained parameter sets for the two different models. Several variants of the method were implemented to investigate their effect on the efficiency of the NSMC method. The first variant implementation of the NSMC is based on a single calibrated model. In the second variant, models were calibrated from different initial parameter sets. NSMC calibration-constrained parameter sets were sampled from these different calibrated models. We demonstrate that in context of nonlinear model, second variant avoids to underestimate parameter uncertainty which may lead to a poor quantification of predictive uncertainty. Application of the proposed approach to manage bioremediation of groundwater in a real site shows that it is effective to provide support in

Bioremediation techniques-classification based on site of application: principles, advantages, limitations and prospects.

Science.gov (United States)

Azubuike, Christopher Chibueze; Chikere, Chioma Blaise; Okpokwasili, Gideon Chijioke

2016-11-01

Environmental pollution has been on the rise in the past few decades owing to increased human activities on energy reservoirs, unsafe agricultural practices and rapid industrialization. Amongst the pollutants that are of environmental and public health concerns due to their toxicities are: heavy metals, nuclear wastes, pesticides, green house gases, and hydrocarbons. Remediation of polluted sites using microbial process (bioremediation) has proven effective and reliable due to its eco-friendly features. Bioremediation can either be carried out ex situ or in situ, depending on several factors, which include but not limited to cost, site characteristics, type and concentration of pollutants. Generally, ex situ techniques apparently are more expensive compared to in situ techniques as a result of additional cost attributable to excavation. However, cost of on-site installation of equipment, and inability to effectively visualize and control the subsurface of polluted sites are of major concerns when carrying out in situ bioremediation. Therefore, choosing appropriate bioremediation technique, which will effectively reduce pollutant concentrations to an innocuous state, is crucial for a successful bioremediation project. Furthermore, the two major approaches to enhance bioremediation are biostimulation and bioaugmentation provided that environmental factors, which determine the success of bioremediation, are maintained at optimal range. This review provides more insight into the two major bioremediation techniques, their principles, advantages, limitations and prospects.

Microbial communities associated with uranium in-situ recovery mining process are related to acid mine drainage assemblages.

Science.gov (United States)

Coral, Thomas; Descostes, Michaël; De Boissezon, Hélène; Bernier-Latmani, Rizlan; de Alencastro, Luiz Felippe; Rossi, Pierre

2018-07-01

A large fraction (47%) of the world's uranium is mined by a technique called "In Situ Recovery" (ISR). This mining technique involves the injection of a leaching fluid (acidic or alkaline) into a uranium-bearing aquifer and the pumping of the resulting solution through cation exchange columns for the recovery of dissolved uranium. The present study reports the in-depth alterations brought to autochthonous microbial communities during acidic ISR activities. Water samples were collected from a uranium roll-front deposit that is part of an ISR mine in operation (Tortkuduk, Kazakhstan). Water samples were obtained at a depth of ca 500 m below ground level from several zones of the Uyuk aquifer following the natural redox zonation inherited from the roll front deposit, including the native mineralized orebody and both upstream and downstream adjacent locations. Samples were collected equally from both the entrance and the exit of the uranium concentration plant. Next-generation sequencing data showed that the redox gradient shaped the community structures, within the anaerobic, reduced, and oligotrophic habitats of the native aquifer zones. Acid injection induced drastic changes in the structures of these communities, with a large decrease in both cell numbers and diversity. Communities present in the acidified (pH values acid mine drainage, with the dominance of Sulfobacillus sp., Leptospirillum sp. and Acidithiobacillus sp., as well as the archaean Ferroplasma sp. Communities located up- and downstream of the mineralized zone under ISR and affected by acidic fluids were blended with additional facultative anaerobic and acidophilic microorganisms. These mixed biomes may be suitable communities for the natural attenuation of ISR mining-affected subsurface through the reduction of metals and sulfate. Assessing the effect of acidification on the microbial community is critical to evaluating the potential for natural attenuation or active bioremediation strategies

Geology, hydrology, chemistry, and microbiology of the in situ bioremediation demonstration site

International Nuclear Information System (INIS)

Newcomer, D.R.; Doremus, L.A.; Hall, S.H.; Truex, M.J.; Vermeul, V.R.; Engelman, R.E.

1995-03-01

This report summarizes characterization information on the geology, hydrology, microbiology, contaminant distribution, and ground-water chemistry to support demonstration of in situ bioremediation at the Hanford Site. The purpose of this information is to provide baseline conditions, including a conceptual model of the aquifer being utilized for in situ bioremediation. Data were collected from sampling and other characterization activities associated with three wells drilled in the upper part of the suprabasalt aquifer. Results of point-dilution tracer tests, conducted in the upper 9 m (30 ft) of the aquifer, showed that most ground-water flow occurs in the upper part of this zone, which is consistent with hydraulic test results and geologic and geophysical data. Other tracer test results indicated that natural ground-water flow velocity is equal to or less than about 0.03 m/d (0.1 ft/d). Laboratory hydraulic conductivity measurements, which represent the local distribution of vertical hydraulic conductivity, varied up to three orders of magnitude. Based on concentration data from both the vadose and saturated zone, it is suggested that most, if not all, of the carbon tetrachloride detected is representative of the aqueous phase. Concentrations of carbon tetrachloride, associated with a contaminant plume in the 200-West Area, ranged from approximately 500 to 3,800 μg/L in the aqueous phase and from approximately 10 to 290 μg/L in the solid phase at the demonstration site. Carbon tetrachloride gas was detected in the vadose zone, suggesting volatilization and subsequent upward migration from the saturated zone

Study of lixiviant damage of a sandstone deposit during in-situ leaching of uranium

International Nuclear Information System (INIS)

Liao Wensheng; Wang Limin; Jiang Yan; Jiang Guoping; Tan Yahui

2014-01-01

The permeability of sandstone deposit is a key factor for economical uranium recovery during in-situ leaching uranium. Low permeability sandstone uranium deposits behave low push-pull capacity, and show formation damage in leaching operations. It is important to study formation damage of permeability, therefore, and to stabilize even improve the push-pull power of drillholes during in-situ leaching. In this paper, formation damage caused by lixiviants was investigated based on a low permeability sandstone uranium deposit. The resulted showed that, under the conditions of in-situ leaching, the salinity of leaching fluid has no harm to formation permeability, on the contrary, the increment of salinity of lixiviant during in-situ leaching improve the permeability of the deposit. The alkalinity, hydrogen peroxide and productivity of the lixiviant cause no significant formation damage. But the fine particles in the lixiviant shows formation damage significantly, and the quantity of the particles should be controlled during production. (authors)

Study of the impact of environmental bacteria ob uranium speciation in order to engage bioremediation process

International Nuclear Information System (INIS)

Untereiner, G.

2008-11-01

Uranium is both a radiological and a chemical toxic. Its concentration in the environment is low except when human activities have caused pollution. Uranium is a heavy reactive element, and thus it is easily complexed with soil component like minerals or organic molecules. These different complexes can be more or less bioavailable for microorganisms and plants, and then get in the human food chain. The knowledge and the understanding of transfer mechanisms and also the fate of toxic elements in the biosphere are a key issue to estimate health and ecological hazards. The knowledge of the speciation is very important for bioremediation processes. Here, we focused on the microorganisms effects onto uranium speciation in environment. Bacteria can accumulate and/or transform uranium depending on the initial form of the element. Thus, its bioavailability could be changed. The species used in this work are Cupriavidus metallidurans CH34, which is an environmental bacteria with a high resistance to heavy metal, Deinococcus radiodurans R1, which is known for his radiological resistance, and Rhodopseudomonas palustris, which is a purple photo-trophic bacteria capable of degrading aromatic compounds. Two forms of uranium were used with these bacteria, a mineral one, uranyl carbonate, and an organic one, uranyl citrate. In a first step, the growth media were modified in order to stabilize uranium complexes thanks to a simulation program. Then, the capacity of the bacteria to accumulate or transform uranium was studied. We saw a difference between minimal inhibition concentrations of these two speciation which is due to a difference between phosphate bioavailability. No accumulation was observed with environmental pH but uranium precipitation was observed with acidic pH (pH 1). Uranium speciation seemed to be well controlled in the growth media and the precipitates were uranyl phosphate. (author)

In situ bioremediation of a diesel fuel spill in northern Manitoba

International Nuclear Information System (INIS)

Hryhoruk, C.D.

1994-01-01

At a northern Manitoba airport, a site was contaminated with diesel fuel, which was confined within the unsaturated zone in silt and silty sand. A two-phase bioremediation process was designed and implemented in-situ in a pilot test. The first phase, ground surface spraying, involved mixing nutrients (ammonium-nitrogen and orthophosphate) with water in a tank and then spraying the mixture on the ground surface above the diesel plume. The second phase, a pump-cycle system, involved pumping groundwater from below the diesel plume into one of two tanks in series. The groundwater underwent both nutrient addition (weekly) and aeration in the tanks, then it was pumped into eight feeder wells which circumscribed an extraction well. Soil testing revealed that both remediation processes aided in increasing subsurface nutrient concentrations and the moisture content within the diesel plume. In addition, high total coliform counts were observed in both the silt and silty sand layers. This implied that conditions for suitable bioremediation can be developed in relatively fine-grained soil. Intermittent soil sampling at three locations over a 14-month period revealed that the diesel plume decreased in size by ca 30% and contaminant concentrations (diesel fuel) also decreased. Plume movement also occurred. The pump-cycle system remains operational. 67 refs., 77 figs., 9 tabs

In situ bioremediation of a diesel fuel spill in northern Manitoba

Energy Technology Data Exchange (ETDEWEB)

Hryhoruk, C D

1994-01-01

At a northern Manitoba airport, a site was contaminated with diesel fuel, which was confined within the unsaturated zone in silt and silty sand. A two-phase bioremediation process was designed and implemented in-situ in a pilot test. The first phase, ground surface spraying, involved mixing nutrients (ammonium-nitrogen and orthophosphate) with water in a tank and then spraying the mixture on the ground surface above the diesel plume. The second phase, a pump-cycle system, involved pumping groundwater from below the diesel plume into one of two tanks in series. The groundwater underwent both nutrient addition (weekly) and aeration in the tanks, then it was pumped into eight feeder wells which circumscribed an extraction well. Soil testing revealed that both remediation processes aided in increasing subsurface nutrient concentrations and the moisture content within the diesel plume. In addition, high total coliform counts were observed in both the silt and silty sand layers. This implied that conditions for suitable bioremediation can be developed in relatively fine-grained soil. Intermittent soil sampling at three locations over a 14-month period revealed that the diesel plume decreased in size by ca 30% and contaminant concentrations (diesel fuel) also decreased. Plume movement also occurred. The pump-cycle system remains operational. 67 refs., 77 figs., 9 tabs.

76 FR 41308 - Strata Energy, Inc., Ross In Situ Recovery Uranium Project, Crook County, WY; Notice of Materials...

Science.gov (United States)

2011-07-13

..., Inc., Ross In Situ Recovery Uranium Project, Crook County, WY; Notice of Materials License Application...-4737, or by e-mail to [email protected] . The Ross In Situ Recovery Uranium Project License... source and byproduct materials license at its Ross In Situ Recovery Uranium Project site located in Crook...

Enhancing in situ bioremediation with pneumatic fracturing

International Nuclear Information System (INIS)

Anderson, D.B.; Peyton, B.M.; Liskowitz, J.L.; Fitzgerald, C.; Schuring, J.R.

1994-04-01

A major technical obstacle affecting the application of in situ bioremediation is the effective distribution of nutrients to the subsurface media. Pneumatic fracturing can increase the permeability of subsurface formations through the injection of high pressure air to create horizontal fracture planes, thus enhancing macro-scale mass-transfer processes. Pneumatic fracturing technology was demonstrated at two field sites at Tinker Air Force Base, Oklahoma City, Oklahoma. Tests were performed to increase the permeability for more effective bioventing, and evaluated the potential to increase permeability and recovery of free product in low permeability soils consisting of fine grain silts, clays, and sedimentary rock. Pneumatic fracturing significantly improved formation permeability by enhancing secondary permeability and by promoting removal of excess soil moisture from the unsaturated zone. Postfracture airflows were 500% to 1,700% higher than prefracture airflows for specific fractured intervals in the formation. This corresponds to an average prefracturing permeability of 0.017 Darcy, increasing to an average of 0.32 Darcy after fracturing. Pneumatic fracturing also increased free-product recovery rates of number 2 fuel from an average of 587 L (155 gal) per month before fracturing to 1,647 L (435 gal) per month after fracturing

Some implications of in situ uranium mining technology development

International Nuclear Information System (INIS)

Cowan, C.E.; Parkhurst, M.A.; Cole, R.J.; Keller, D.; Mellinger, P.J.; Wallace, R.W.

1980-09-01

A technology assessment was initiated in March 1979 of the in-situ uranium mining technology. This report explores the impediments to development and deployment of this technology and evaluates the environmental impacts of a generic in-situ facility. The report is divided into the following sections: introduction, technology description, physical environment, institutional and socioeconomic environment, impact assessment, impediments, and conclusions

The application of geophysical logging at in-situ leaching uranium mine in China

International Nuclear Information System (INIS)

Liu Zeyao; Xu Shusheng; Li Zhongqiu

1999-01-01

The status of work, instrument and method employed for geophysical logging in different stages at in-situ leaching uranium mine are discussed and the development of software, electrical current logging and gamma ray logging are presented based on the requirement of in-situ leaching of uranium. In addition, new function and method with regard to home instrument are proposed for future work

Variably Saturated Flow and Multicomponent Biogeochemical Reactive Transport Modeling of a Uranium Bioremediation Field Experiment

International Nuclear Information System (INIS)

Yabusaki, Steven B.; Fang, Yilin; Williams, Kenneth H.; Murray, Christopher J.; Ward, Anderson L.; Dayvault, Richard; Waichler, Scott R.; Newcomer, Darrell R.; Spane, Frank A.; Long, Philip E.

2011-01-01

Field experiments at a former uranium mill tailings site have identified the potential for stimulating indigenous bacteria to catalyze the conversion of aqueous uranium in the +6 oxidation state to immobile solid-associated uranium in the +4 oxidation state. This effectively removes uranium from solution resulting in groundwater concentrations below actionable standards. Three-dimensional, coupled variably-saturated flow and biogeochemical reactive transport modeling of a 2008 in situ uranium bioremediation field experiment is used to better understand the interplay of transport rates and biogeochemical reaction rates that determine the location and magnitude of key reaction products. A comprehensive reaction network, developed largely through previous 1-D modeling studies, was used to simulate the impacts on uranium behavior of pulsed acetate amendment, seasonal water table variation, spatially-variable physical (hydraulic conductivity, porosity) and geochemical (reactive surface area) material properties. A principal challenge is the mechanistic representation of biologically-mediated terminal electron acceptor process (TEAP) reactions whose products significantly alter geochemical controls on uranium mobility through increases in pH, alkalinity, exchangeable cations, and highly reactive reduction products. In general, these simulations of the 2008 Big Rusty acetate biostimulation field experiment in Rifle, Colorado confirmed previously identified behaviors including (1) initial dominance by iron reducing bacteria that concomitantly reduce aqueous U(VI), (2) sulfate reducing bacteria that become dominant after ∼30 days and outcompete iron reducers for the acetate electron donor, (3) continuing iron-reducer activity and U(VI) bioreduction during dominantly sulfate reducing conditions, and (4) lower apparent U(VI) removal from groundwater during dominantly sulfate reducing conditions. New knowledge on simultaneously active metal and sulfate reducers has been

Geochemical and microbiological characteristics during in situ chemical oxidation and in situ bioremediation at a diesel contaminated site.

Science.gov (United States)

Sutton, Nora B; Kalisz, Mariusz; Krupanek, Janusz; Marek, Jan; Grotenhuis, Tim; Smidt, Hauke; de Weert, Jasperien; Rijnaarts, Huub H M; van Gaans, Pauline; Keijzer, Thomas

2014-02-18

While in situ chemical oxidation with persulfate has seen wide commercial application, investigations into the impacts on groundwater characteristics, microbial communities and soil structure are limited. To better understand the interactions of persulfate with the subsurface and to determine the compatibility with further bioremediation, a pilot scale treatment at a diesel-contaminated location was performed consisting of two persulfate injection events followed by a single nutrient amendment. Groundwater parameters measured throughout the 225 day experiment showed a significant decrease in pH and an increase in dissolved diesel and organic carbon within the treatment area. Molecular analysis of the microbial community size (16S rRNA gene) and alkane degradation capacity (alkB gene) by qPCR indicated a significant, yet temporary impact; while gene copy numbers initially decreased 1-2 orders of magnitude, they returned to baseline levels within 3 months of the first injection for both targets. Analysis of soil samples with sequential extraction showed irreversible oxidation of metal sulfides, thereby changing subsurface mineralogy and potentially mobilizing Fe, Cu, Pb, and Zn. Together, these results give insight into persulfate application in terms of risks and effective coupling with bioremediation.

In-situ bioremediation of a hydrocarbon-contaminated pond at Hall Beach, Northwest Territories

International Nuclear Information System (INIS)

Eno, R.; Rogers, J.; Heroux, J.; Reimer, K.

1999-01-01

The effectiveness of in-situ bioremediation as a means of cleaning up fuel spills in Arctic regions is demonstrated by a case study involving a former fuel tank farm site at Hall Beach, Northwest Territories. An in-situ treatment method, based on the theory of a completely mixed batch wastewater system, was used in this instance. The treatment centred around a commercial floating aerator, which was installed in the pond to provide oxygen. Pre-calculated amounts of nutrients in the form of ammonium chloride and sodium phosphate were also added. The treatment was repeated in the following thawing season to verify initial results. The study is still ongoing; analysis results of the samples collected during the second season are not yet available. However, initial results looked promising and were consistent with what would be expected of increased biological activity. 4 figs

Study on tertiary in-situ leachable uranium mineralization conditions in South Songliao basin

International Nuclear Information System (INIS)

Zhang Zhenqiang; Li Guokuan; Zhao Zonghua; Zhang Jingxun

2001-01-01

Tertiary in-situ leachable mineralization in Songliao Basin was analyzed in theory in the past. Since 1998, regional investigation at 1:200000 scale has been done with about 120 holes drilled. Based on drill holes recording, section compiling and sample analysis, the authors investigate into the Tertiary in-situ leachable conditions including rock character, sedimentary facies, rock chemistry, organic substances, uranium content, sandstone porosity, sandstone bodies, interlayer oxidation, and hydro-dynamic value. The study would play important role in prospecting for in-situ leachable uranium in South Songliao basin

Aquifer restoration techniques for in-situ leach uranium mines

International Nuclear Information System (INIS)

Deutsch, W.J.; Bell, N.E.; Mercer, B.W.; Serne, R.J.; Shade, J.W.; Tweeton, D.R.

1984-02-01

In-situ leach uranium mines and pilot-scale test facilities are currently operating in the states of Wyoming, Texas, New Mexico and Colorado. This report summarizes the technical considerations involved in restoring a leached ore zone and its aquifer to the required level. Background information is provided on the geology and geochemistry of mineralized roll-front deposits and on the leaching techniques used to extract the uranium. 13 references, 13 figures, 4 tables

Economic evaluation of in situ extraction for copper, gold, and uranium

International Nuclear Information System (INIS)

Lewis, F.M.; Chase, C.K.; Bhappu, R.B.

1976-01-01

In situ extraction for copper, gold, and uranium, generally involves several common alternative processes and techniques. These include dump leaching, heap leaching, leaching of fractured ore in-place or bore hole mining and unit operations such as cementation, solvent extraction, ion-exchange, or carbon-in-pulp. Since the metallurgical effectiveness and economics of such processes and unit operations are well established, it would be possible to select the optimum alternative for extracting either copper, gold, or uranium from their ores using in situ extraction technology. Efforts made to provide metallurgical evaluation as well as capital and operating costs for the various processes and unit operations are reported. These costs are used in preparing feasibility studies for in situ extraction of these metals

77 FR 70486 - Supplemental Environmental Impact Statement for Proposed Dewey-Burdock In-Situ Uranium Recovery...

Science.gov (United States)

2012-11-26

... Proposed Dewey- Burdock In-Situ Uranium Recovery Project in Custer and Fall River Counties, SD AGENCY... draft Supplemental Environmental Impact Statement (Draft SEIS) for the Dewey-Burdock In-Situ Uranium... NRC for a new source materials license for the Dewey-Burdock ISR Project. Powertech is proposing to...

Introduction to in situ leaching technique and facility at Smith Ranch uranium project in USA

International Nuclear Information System (INIS)

Xu Lechang; Wang Delin; Sun Xianrong; Gao Shangxiong

2005-01-01

The history of in situ leaching of uranium in USA is reviewed. Some techniques and parameters of alkaline in situ leach at Smith Ranch uranium project are introduced, including well field, sorption, elution, precipitation, filter and drying, automatic control, radiation protection, safety and environmental protection. (authors)

Contamination-remedying technology based on biotechnology. ; Bioremediation. Biotechnology wo mochiita osen shufuku gijutsu. ; Bioremediation

Energy Technology Data Exchange (ETDEWEB)

Nishimura, M [The Japan Research Institute, Ltd., Osaka (Japan)

1993-08-01

Bioremediation technology is outlined. The bioremediation technology is a contamination-remedying technology for the injurious chemical matter discharged in the environment to be made innocuous by utilizing the decomposing ability of microorganisms. That technology is characterized by its energywise economical performance, secondary waste which is not producible and remedy which is possible on site against the contamination. As a treatment system, that technology comprises solid phase bioremediation (The contaminated soil is purified in a soil treatment unit.), slurry phase bioremediation (The contaminated soil is made slurry and decomposed by microorganisms.) and in-situ bioremediation (The treatment is made by injecting nutrients and microorganisms underground.). As for how to use the microorganisms, there are two methods: One in which living groups of microorganisms are activated and the other in which microorganisms are artificially cultivated. As contaminants in the US, listed are organic solvent, wood preservative, high-molecular aromatic halide, agricultural chemical, military waste, heavy metal waste and radioactive waste. 11 refs., 5 figs., 1 tab.

Applied bioremediation of hazardous, petroleum, and industrial wastes

International Nuclear Information System (INIS)

Ulm, D.J.; McGuire, P.N.; Lynch, E.R.

1994-01-01

Blasland and Bouck Engineers, P.C. (Blasland and Bouck) conducted a large-scale soil bioremediation pilot study at an inactive hazardous waste site in Upstate New York. Remediation of soils at the site is regulated in accordance with a Consent Order entered into with the New York State Department of Environmental Conservation. The chemicals of concern in soils at the site consist of a wide range of volatile and semi-volatile organic compounds including: trichloroethylene, methylene chloride, methanol, aniline, and N,N-dimethylaniline. The large-scale soil Bioremediation Pilot Study consisted of evaluating the effectiveness of two bioremediation techniques: ex-situ solid phase treatment of excavation soils; and in-situ solid phase treatment with soil mixing. The feasibility of bioremediation for soils at this site was evaluated in the field at pilot scale due to the generally high sensitivity of the technology's effectiveness and feasibility from site to site

Getting results in bioremediation

International Nuclear Information System (INIS)

Konzuk, Julie

2014-01-01

Bioremediation can be a sustainable, low-cost solution for many contaminated sites, but it is important to know which sites are suitable and be aware of common pitfalls. Chlorinated solvents, lighter petroleum hydrocarbons, non-aqueous phase liquids have all be demonstrated to be readily biodegradable. However, the success of enhanced in situ bioremediation (EISB) depends on the successful growth and establishment of a viable, mature microbial community. Low or high pH groundwater, or high concentrations of some chemicals can inhibit microbial activity.

A comparison of bioaugmentation and intrinsic in situ bioremediation of a PAH contaminated site

International Nuclear Information System (INIS)

Geddes, T.; Mortier, N.; Chaparian, M.

1995-01-01

Polycyclic aromatic hydrocarbons (PAHs) are one of the most common environmental hazards, naturally occurring in petroleum and its by-products. They are encountered at nearly all UST sites, and present an impediment to the use of cost effective intrinsic in situ bioremediation due to their recalcitrant nature. Even bacteria isolated specifically for their ability to degrade PAHs in the laboratory have shown no significant degradative capabilities in the field. This is due to the unique balance that exists at every contaminated site between the microbial ecology, chemical, physical, and environmental factors. Therefore, bacteria indigenous to the site and acclimated to these environmental parameters should be well suited for use in bioaugmentation. Based on this assumption, a new and innovative approach to bioaugmentation has been developed which consists of a series of scientifically-sound, rational steps in the use of this technology. Initially, careful chemical and biological analyses of site samples are conducted using conventional analytical instrumentation and state-of-the-art microbiological, biochemical, and molecular biological techniques. Bacteria from site samples that demonstrate potential PAH degradative capability are isolated. The bacteria are then enriched in culture and re-introduced to the site with appropriate nutrients. Further, this approach encompasses the proposed guidelines for proving the efficacy of in situ bioremediation as set forth by the National Science Foundation. To demonstrate the effectiveness of this approach, data are presented here of a laboratory-scale trial of a PAH contaminated site

Identification of chemical processes influencing constituent mobility during in-situ uranium leaching

International Nuclear Information System (INIS)

Sherwood, D.R.; Hostetler, C.J.; Deutsch, W.J.

1984-07-01

In-situ leaching of uranium has become a widely accepted method for production of uranium concentrate from ore zones that are too small, too deep, and/or too low in grade to be mined by conventional techniques. One major environmental concern that exists with in-situ leaching of uranium is the possible adverse effects mining might have on regional ground water quality. The leaching solution (lixiviant), which extracts uranium from the ore zone, might also mobilize other potential contaminants (As, Se, Mo, and SO 4 ) associated with uranium ore. Column experiments were performed to investigate the geochemical interactions between a lixiviant and a uranium ore during in-situ leaching and to identify chemical processes that might influence contaminant mobility. The analytical composition data for selected column effluents were used with the MINTEQ code to develop a computerized geochemical model of the system. MINTEQ was used to calculate saturation indices for solid phases based on the composition of the solution. A potential constraint on uranium leaching efficiency appears to be the solubility control of schoepite. Gypsum and powellite solubilities may limit the mobilities of sulfate and molybdenum, respectively. In contrast, the mobilities of arsenic and selenium were not limited by solubility constraints, but were influenced by other chemical interaction between the solution and sediment, perhaps adsorption. Bulk chemical and mineralogical analyses were performed on both the original and leached ores. Using these analyses together with the column effluent data, mass balance calculations were performed on five constituents based on solution chemical analysis and bulk chemical and γ-spectroscopy analysis for the sediment. 6 references, 10 figures, 10 tables

In Situ Immobilization of Uranium in Structured Porous Media via Biomineralization at the Fracture/Matrix Interface – Subproject to Co-PI Eric E. Roden

Energy Technology Data Exchange (ETDEWEB)

Eric E. Roden

2007-11-02

Although the biogeochemical processes underlying in situ bioremediation technologies are increasingly well understood, field-scale heterogeneity (both physical and biogeochemical) remains a major obstacle to successful field-scale implementation. In particular, slow release of contamination from low-permeability regions (primarily by diffusive/dispersive mass transfer) can hinder the effectiveness of remediation. The research described in this report was conducted in conjunction with a project entitled “In Situ Immobilization of Uranium in Structured Porous Media via Biomineralization at the Fracture/Matrix Interface”, which was funded through the Field Research element of the former NABIR Program (now the Environmental Remediation Sciences Program) within the Office of Biological and Environmental Research. Dr. Timothy Scheibe (Pacific Northwest National Laboratory) was the overall PI/PD for the project, which included Scott Brooks (Oak Ridge National Laboratory) and Eric Roden (formerly at The University of Alabama, now at the University of Wisconsin) as separately-funded co-PIs. The overall goal of the project was to evaluate strategies that target bioremediation at interfaces between high- and low-permeability regions of an aquifer in order to minimize the rate of contaminant transfer into high-permeability/high fluid flow zones. The research was conducted at the Area 2 site of the Field Research Center (FRC) at Oak Ridge National Laboratory (ORNL). Area 2 is a shallow pathway for migration of contaminated groundwater to seeps in the upper reach of Bear Creek at ORNL, mainly through a ca. 1 m thick layer of gravel located 4-5 m below the ground surface. Hydrological tracer studies indicate that the gravel layer receives input of uranium from both upstream sources and from diffusive mass transfer out of highly contaminated fill and saprolite materials above and below the gravel layer. We sought to test the hypothesis that injection of electron donor into

In-situ uranium mining: reservoir engineering aspects of leaching and restoration

International Nuclear Information System (INIS)

Kabir, M.I.

1982-01-01

To establish the feasibility of in-situ mining of uranium, a push-pull test of an in-situ uranium leaching process, which consists of a single injection/production test well and two observation wells, was designed to evaluate the parameters which govern the uranium production and restorability of a solution mined zone. The test procedure itself consists of injection (push cycle) of a preflush followed by lixiviant, a brief soak period (soak cycle), and subsequent production (pull cycle) into the same well. Based on computer modeling, procedures are defined which permit, for a properly designed test, the determination of both restoration and leaching parameters. The test procedure and design recommendations are also outlined. Two numerical simulators which model field scale uranium production and restoration operations are presented. These simulators are able to accommodate various well patterns and irregular reservoir boundaries, physical dispersion, directional permeability variations (if present), and a variety of injection/production strategies. A streamline-concentration balance technique has been used to develop the models. The assumption of time invariant boundary conditions and no transverse dispersion between the streamlines reduces the two dimensional problem to a bundle of one dimensional ones. It has been further shown that the production well effluent histories can easily be obtained by superposing the solution of the concentration balance equations for a single streamline, and thus reducing computation time significantly. Finally, the simulators have been used to study various reservoir engineering aspects to optimize in-situ uranium production from field scale operations

In-situ uranium mining: reservoir engineering aspects of leaching and restoration

Energy Technology Data Exchange (ETDEWEB)

Kabir, M.I.

1982-01-01

To establish the feasibility of in-situ mining of uranium, a push-pull test of an in-situ uranium leaching process, which consists of a single injection/production test well and two observation wells, was designed to evaluate the parameters which govern the uranium production and restorability of a solution mined zone. The test procedure itself consists of injection (push cycle) of a preflush followed by lixiviant, a brief soak period (soak cycle), and subsequent production (pull cycle) into the same well. Based on computer modeling, procedures are defined which permit, for a properly designed test, the determination of both restoration and leaching parameters. The test procedure and design recommendations are also outlined. Two numerical simulators which model field scale uranium production and restoration operations are presented. These simulators are able to accommodate various well patterns and irregular reservoir boundaries, physical dispersion, directional permeability variations (if present), and a variety of injection/production strategies. A streamline-concentration balance technique has been used to develop the models. The assumption of time invariant boundary conditions and no transverse dispersion between the streamlines reduces the two dimensional problem to a bundle of one dimensional ones. It has been further shown that the production well effluent histories can easily be obtained by superposing the solution of the concentration balance equations for a single streamline, and thus reducing computation time significantly. Finally, the simulators have been used to study various reservoir engineering aspects to optimize in-situ uranium production from field scale operations.

Operations Support of Phase 2 Integrated Demonstration In Situ Bioremediation. Volume 1, Final report: Final report text data in tabular form, Disk 1

Energy Technology Data Exchange (ETDEWEB)

Hazen, T.C. [Westinghouse Savannah River Co., Aiken, SC (United States)

1993-09-01

This project was designed to demonstrate in situ bioremediation of ground water and sediment contaminated with chlorinated solvents. Indigenous microorganisms were stimulated to degrade trichlorethylene (TCE), tetrachloroethylene (PCE) and their daughter products in situ by addition of nutrients to the contaminated aquifer and adjacent vadose zone. The principle carbon/energy source nutrient used in this demonstration was methane (natural gas). In situ biodegradation is a highly attractive technology for remediation because contaminants are destroyed, not simply moved to another location or immobilized, thus decreasing costs, risks, and time, while increasing efficiency, safety, and public and regulatory acceptability. This report describes the preliminary results of the demonstration and provides conclusions only for those measures that the Bioremediation Technical Support Group felt were so overwhelmingly convincing that they do not require further analyses. Though this report is necessarily superficial it does intend to provide a basis for further evaluating the technology and for practitioners to immediately apply some parts of the technology.

Introduction to In Situ Bioremediation of Groundwater

Science.gov (United States)

Bioremediation is an engineered technology that modifies environmental conditions (physical, chemical, biochemical, or microbiological) to encourage microorganisms to destroy or detoxify organic and inorganic contaminants in the environment.

Following the electroreduction of uranium dioxide to uranium in LiCl–KCl eutectic in situ using synchrotron radiation

Energy Technology Data Exchange (ETDEWEB)

Brown, L.D.; Abdulaziz, R.; Jervis, R.; Bharath, V.J. [Electrochemical Innovation Lab, Dept. Chemical Engineering, UCL, London WC1E 7JE (United Kingdom); Atwood, R.C.; Reinhard, C.; Connor, L.D. [Diamond Light Source, Harwell Science and Innovation Campus, Didcot, Oxfordshire OX11 0DE (United Kingdom); Simons, S.J.R.; Inman, D.; Brett, D.J.L. [Electrochemical Innovation Lab, Dept. Chemical Engineering, UCL, London WC1E 7JE (United Kingdom); Shearing, P.R., E-mail: p.shearing@ucl.ac.uk [Electrochemical Innovation Lab, Dept. Chemical Engineering, UCL, London WC1E 7JE (United Kingdom)

2015-09-15

Highlights: • We investigated the electroreduction of UO{sub 2} to U in LiCl/KCL eutectic molten salt. • Combined electrochemical measurement and in situ XRD is utilised. • The electroreduction appears to occur in a single, 4-electron-step, process. • No intermediate compounds were observed. - Abstract: The electrochemical reduction of uranium dioxide to metallic uranium has been investigated in lithium chloride–potassium chloride eutectic molten salt. Laboratory based electrochemical studies have been coupled with in situ energy dispersive X-ray diffraction, for the first time, to deduce the reduction pathway. No intermediate phases were identified using the X-ray diffraction before, during or after electroreduction to form α-uranium. This suggests that the electrochemical reduction occurs via a single, 4-electron-step, process. The rate of formation of α-uranium is seen to decrease during electrolysis and could be a result of a build-up of oxygen anions in the molten salt. Slow transport of O{sup 2−} ions away from the UO{sub 2} working electrode could impede the electrochemical reduction.

Bioremediation at a petroleum refinery

International Nuclear Information System (INIS)

Carson, A.W.; Jarvis, J.; Richardson, K.E.

1994-01-01

This paper presents a summary of three projects at the Mobil Refinery in Torrance, California where bioremediation technologies were successfully employed for the remediation of hydrocarbon contaminated soil. The three projects represent variations of implementation of bioremediation, both in-situ and ex-situ. Soil from all of the projects was considered non-hazardous designated waste under the California Code of Regulations, Title 23, section 2522. The projects were permitted and cleanup requirements were defined with the Los Angeles Regional Water Quality Control Board. In all of the projects, different methods were used for supplying water, oxygen, and nutrients to the hydrocarbon degrading bacteria to stimulate growth. The Stormwater Retention Basin Project utilized in-situ mechanical mixing of soils to supply solid nutrients and oxygen, and a self-propelled irrigation system to supply water. The Tank Farm Lake project used an in-situ active bioventing technology to introduce oxygen, moisture, and vapor phase nutrients. The Tank 1340X247 project was an ex-situ bioventing remediation project using a drip irrigation system to supply water and dissolved nutrients, and a vapor extraction system to provide oxygen

In Situ Immobilization of Uranium in Structured Porous Media via Biomineralization at the Fracture/Matrix Interface - Subproject to Co-PI Eric E. Roden. Final report

International Nuclear Information System (INIS)

Roden, Eric E.

2007-01-01

Although the biogeochemical processes underlying in situ bioremediation technologies are increasingly well understood, field-scale heterogeneity (both physical and biogeochemical) remains a major obstacle to successful field-scale implementation. In particular, slow release of contamination from low-permeability regions (primarily by diffusive/dispersive mass transfer) can hinder the effectiveness of remediation. The research described in this report was conducted in conjunction with a project entitled ''In Situ Immobilization of Uranium in Structured Porous Media via Biomineralization at the Fracture/Matrix Interface'', which was funded through the Field Research element of the former NABIR Program (now the Environmental Remediation Sciences Program) within the Office of Biological and Environmental Research. Dr. Timothy Scheibe (Pacific Northwest National Laboratory) was the overall PI/PD for the project, which included Scott Brooks (Oak Ridge National Laboratory) and Eric Roden (formerly at The University of Alabama, now at the University of Wisconsin) as separately-funded co-PIs. The overall goal of the project was to evaluate strategies that target bioremediation at interfaces between high- and low-permeability regions of an aquifer in order to minimize the rate of contaminant transfer into high-permeability/high fluid flow zones. The research was conducted at the Area 2 site of the Field Research Center (FRC) at Oak Ridge National Laboratory (ORNL). Area 2 is a shallow pathway for migration of contaminated groundwater to seeps in the upper reach of Bear Creek at ORNL, mainly through a ca. 1 m thick layer of gravel located 4-5 m below the ground surface. Hydrological tracer studies indicate that the gravel layer receives input of uranium from both upstream sources and from diffusive mass transfer out of highly contaminated fill and saprolite materials above and below the gravel layer. We sought to test the hypothesis that injection of electron donor into this

Restoration of uranium in-situ leaching sites

International Nuclear Information System (INIS)

Hill, A.D.; Silberberg, I.H.; Walsh, M.P.; Breland, W.M.; Humenick, M.J.; Schechter, R.S.

1980-01-01

Ammonium ions introduced into the formation during in-situ uranium leach mining must be removed by a restoration process. Ion exchange processes to strip sorbed ammonium cation from the clays have been modeled and studied experimentally. It is concluded that ammonium removal can be accomplished best by a high-ionic-strength flush. The migration of uncovered ammonium cation in groundwater also is studied. 19 refs

Creosote-contaminated sites: their potential for bioremediation

Energy Technology Data Exchange (ETDEWEB)

Mueller, J G; Chapman, P J; Pritchard, P H [US EPA Environmental Research Laboratory, Gulf Breeze, FL (USA)

1989-10-01

Coal tar creosote contamination is generally associated with surface soils, waters in treatment lagoons or evaporation areas, and groundwater contaminated with leachate from the above sources. The basic principle of bioremediation is to exploit the ability of microorganisms to catabolize a wide range of organic substrates. There are limitations which much be addressed if in situ bioremediation is to be successful: the pollutant must be in a chemical state conducive to microbial utilization, aeration and nutrient supplementation are essential elements of many in situ treatments, and there must be present an acclimated microbial population capable of degrading the pollutant. 35 refs., 3 tabs.

Contaminants at DOE sites and their susceptibility to bioremediation

International Nuclear Information System (INIS)

Lenhard, R.J.; Skeen, R.S.; Brouns, T.M.

1993-11-01

Contaminants at DOE sites encompass a range of common industrial pollutants. However, the prevalence of contaminant mixtures including organics, metals, and radionuclides is relatively unique to DOE's facilities. Bioremediation has been shown to be effective for destruction of many of the organic pollutants. The technology also has promise for application to many of the metals and radionuclides; however, field demonstrations for these applications have not yet been attempted. Because of the complexity of biodegradation of even a single-compound class, little has been done to develop or demonstrate in situ bioremediation technologies for multicompound combinations. The current bioremediation demonstration on CCl 4 and nitrates within the VOC-Arid Integrated Demonstration is one the first efforts to address inorganic and organic co-contaminants simultaneously. Additional research, technology development, and field demonstrations are needed to evaluate the applicability of in situ bioremediation to DOE's most common contaminant mixtures

Bioremediation of marine oil pollution

International Nuclear Information System (INIS)

Gutnick, D.L.

1991-11-01

An assessment is presented of the scientific and technological developments in the area of bioremediation and biodegradation of marine oil pollution. A number of allied technologies are also considered. The basic technology in bioremediation involves adding fertilizers to an oil spill to enhance the natural process of oil biodegradation. Bioremediation can be applied to open systems such as beach or land spills, or in closed and controlled environments such as storage containers, specially constructed or modified bioreactors, and cargo tanks. The major advantage of using closed environments is the opportunity to control the physical and nutritional parameters to optimize the rate of biodegradation. An evaluation of the state of the art of bioremediation in Canada is also included. Recommendations are made to involve the Canadian Transportation Development Centre in short-term research projects on bioremediation. These projects would include the use of a barge as a mobile bioreactor for the treatment of off-loaded oily waste products, the use of in-situ bioremediation to carry out extensive cleaning, degassing, and sludge remediation on board an oil tanker, and the use of a barge as a mobile bioreactor and facility for the bioremediation of bilges. 51 refs., 4 figs., 14 tabs

Bioremediation of marine oil pollution

Energy Technology Data Exchange (ETDEWEB)

Gutnick, D L

1991-11-01

An assessment is presented of the scientific and technological developments in the area of bioremediation and biodegradation of marine oil pollution. A number of allied technologies are also considered. The basic technology in bioremediation involves adding fertilizers to an oil spill to enhance the natural process of oil biodegradation. Bioremediation can be applied to open systems such as beach or land spills, or in closed and controlled environments such as storage containers, specially constructed or modified bioreactors, and cargo tanks. The major advantage of using closed environments is the opportunity to control the physical and nutritional parameters to optimize the rate of biodegradation. An evaluation of the state of the art of bioremediation in Canada is also included. Recommendations are made to involve the Canadian Transportation Development Centre in short-term research projects on bioremediation. These projects would include the use of a barge as a mobile bioreactor for the treatment of off-loaded oily waste products, the use of in-situ bioremediation to carry out extensive cleaning, degassing, and sludge remediation on board an oil tanker, and the use of a barge as a mobile bioreactor and facility for the bioremediation of bilges. 51 refs., 4 figs., 14 tabs.

78 FR 19330 - Supplemental Environmental Impact Statement for the Ross In-Situ Uranium Recovery Project in...

Science.gov (United States)

2013-03-29

... Ross In-Situ Uranium Recovery Project in Crook County, Wyoming AGENCY: Nuclear Regulatory Commission... Commission (NRC) for a new source materials license for the proposed Ross In-Situ Uranium Recovery (ISR) Project (Ross Project) proposed to be located in Crook County, Wyoming. The NRC is issuing for public...

Application of anatectic mineralization to prospecting in-situ leachable sandstone type uranium ore in South Songliao Basin

International Nuclear Information System (INIS)

Zhao Zhonghua

2001-01-01

The deep ore-forming origin is a new theory for prospecting in-situ leachable sandstone type uranium. Tectonics, lithologic and geochemistry are basic forecasting criteria. Previous unconsolidated sand, source area and geochemical barrier are three essential conditions for forming uranium deposit. Metallogenic environment and prospective region are found. Tertiary system is prospective layer for prospecting in-situ leachable sandstone type uranium ore in south Songliao Basin

Aluminum chloride restoration of in situ leached uranium ores

International Nuclear Information System (INIS)

Grant, D.C.; Burgman, M.A.

1982-01-01

During in situ uranium mining using ammonium bicarbonate lixiviant, the ammonium exchanges with cations on the ore's clay. After mining is complete, the ammonium may desorb into post-leach ground water. For the particular ore studied, other chemicals (i.e., uranium and selenium) which are mobilized during the leach process, have also been found in the post-leach ground water. Laboratory column tests, used to simulate the leaching process, have shown that aluminum chloride can rapidly remove ammonium from the ore and thus greatly reduce the subsequent ammonium leakage level into ground water. The aluminum chloride has also been found to reduce the leakage levels of uranium and selenium. In addition, the aluminum chloride treatment produces a rapid improvement in permeability

Supplementary recovery of uranium by in-situ leaching at the Brugeaud deposit (Limousin, France)

International Nuclear Information System (INIS)

Lyaudet, G.

1980-01-01

The actual mining operations at the Brugeaud Deposit (West Brugeaud and East Brugeaud) were followed by supplementary recoveries of uranium by means of in-situ leaching. There were a number of factors which favoured consideration of these operations: the amounts of uranium present at the edge of the stoped areas; the underground mining infrastructure, which did not require supplementary operations for the recovery of solutions; the nature of the rock, which presented a dense network of fractures and micro-fractures conducive to impregnation by the acid solutions; and the immediate proximity of a concentration plant. The amount of uranium recovered by in-situ leaching is close to 200 t. This production is approximately nine per cent of all the uranium extracted from the deposit. The cost of the metal obtained in this way was always less than FF 100 (FF of 1978) per kilogram of uranium. (author)

Magnesium bicarbonate as an in situ uranium lixiviant

International Nuclear Information System (INIS)

Sibert, J.W.

1984-01-01

In the subsurface solution mining of mineral values, especially uranium, in situ, magnesium bicarbonate leaching solution is used instead of sodium, potassium and ammonium carbonate and bicarbonates. The magnesium bicarbonate solution is formed by combining carbon dioxide with magnesium oxide and water. The magnesium bicarbonate lixivant has four major advantages over prior art sodium, potassium and ammonium bicarbonates

In-situ leaching opens new uranium reserves in Texas

International Nuclear Information System (INIS)

White, L.

1975-01-01

A commercial in-situ uranium leaching operation that is quite probably the largest ever built started up in April, 10 mi southwest of George West, Tex. Producing from a pattern of 66 injection wells and 46 extraction wells occupying an area of less than 3 acres, the Clay West mine and plant are expected to reach design capacity of 250,000 lb per year of yellowcake by the end of the summer. By late May, results were sufficiently favorable to make the owners think seriously about an early expansion. Built at a cost of $7 million by joint ventures Atlantic Richfield (50 percent owner and operator), Dalco (25 percent), and US Steel (25 percent), the Clay West mine may be only the first of several mines to extract U 3 O 8 from a uranium province that stretches from north of Houston to Brownsville, at the southernmost tip of the state. Westinghouse subsidiary Wyoming Minerals is building a 250,000-lb-per-year plant near Bruni, with startup planned before the end of 1975, and Mobil Oil is setting up a pilot-scale plant in the same area. A number of other companies are reported to be actively interested in development of in-situ uranium leaching in Texas. (U.S.)

In situ leaching of uranium in South Australia

International Nuclear Information System (INIS)

Matthews, D.

1998-01-01

The proposed two new uranium mines at Beverley and Honeymoon, South Australia plan to use the cheap but potentially polluting process of in situ leaching (ISL) and permission has already been given for experimental underground leaching at Beverley. The mining industry describes ISL as environmentally benign because, instead of excavating, a corrosive liquid such as sulphuric acid is used. The liquid, sometimes 10000 times more acid than the aquifer water, is pumped into the ground in order to leach out the uranium and the resulting solution is then pumped to the surface where the uranium is extracted. Because the groundwater is salty and radioactive, the mining companies regard it as useless, so its contamination by ISL is considered of no concern. Salty radioactive water can be purified or desalinated and such processes are commonly used by mining companies such as Western Mining Corporation at Roxby Downs. (author)

Sensitivity Analysis and Parameter Estimation for a Reactive Transport Model of Uranium Bioremediation

Science.gov (United States)

Meyer, P. D.; Yabusaki, S.; Curtis, G. P.; Ye, M.; Fang, Y.

2011-12-01

A three-dimensional, variably-saturated flow and multicomponent biogeochemical reactive transport model of uranium bioremediation was used to generate synthetic data . The 3-D model was based on a field experiment at the U.S. Dept. of Energy Rifle Integrated Field Research Challenge site that used acetate biostimulation of indigenous metal reducing bacteria to catalyze the conversion of aqueous uranium in the +6 oxidation state to immobile solid-associated uranium in the +4 oxidation state. A key assumption in past modeling studies at this site was that a comprehensive reaction network could be developed largely through one-dimensional modeling. Sensitivity analyses and parameter estimation were completed for a 1-D reactive transport model abstracted from the 3-D model to test this assumption, to identify parameters with the greatest potential to contribute to model predictive uncertainty, and to evaluate model structure and data limitations. Results showed that sensitivities of key biogeochemical concentrations varied in space and time, that model nonlinearities and/or parameter interactions have a significant impact on calculated sensitivities, and that the complexity of the model's representation of processes affecting Fe(II) in the system may make it difficult to correctly attribute observed Fe(II) behavior to modeled processes. Non-uniformity of the 3-D simulated groundwater flux and averaging of the 3-D synthetic data for use as calibration targets in the 1-D modeling resulted in systematic errors in the 1-D model parameter estimates and outputs. This occurred despite using the same reaction network for 1-D modeling as used in the data-generating 3-D model. Predictive uncertainty of the 1-D model appeared to be significantly underestimated by linear parameter uncertainty estimates.

Bioremediation of a crude oil polluted tropical rain forest soil ...

African Journals Online (AJOL)

These results suggest that Biostimulation with tilling (nutrient enhanced in-situ bioremediation) and or the combination ofBiostimulation and Bioaugumentation with indigenous hydrocarbon utilizers would be effective in the remediation of crude oil polluted tropical soils. Key Words: Bioremediation, Bioaugumentation, ...

TECHNOLOGIES FOR BIOREMEDIATION OF SOILS CONTAMINATED WITH PETROLEUM PRODUCTS

Directory of Open Access Journals (Sweden)

Roxana Gabriela POPA

2012-05-01

Full Text Available Biological methods for remediation of soils is based on the degradation of pollutants due to activity of microorganisms (bacteria, fungi. Effectiveness of biological decontamination of soils depends on the following factors: biodegradation of pollutants, type of microorganisms used, choice of oxidant and nutrient and subject to clean up environmental characteristics. Ex situ techniques for bioremediation of soils polluted are: composting (static / mechanical agitation, land farming and biopiles. Techniques in situ bioremediation of soils polluted are: bioventingul, biospargingul and biostimulation – bioaugumentarea.

Analysis of groundwater criteria and recent restoration attempts after in situ uranium leaching. Open file report

International Nuclear Information System (INIS)

Buma, G.; Johnson, P.H.; Bienek, G.K.; Watson, C.G.; Noyes, H.J.

1981-10-01

Groundwater restoration is an important aspect of in situ uranium leaching. Information on the effectiveness of the current technology, costs, and the current State and Federal Government permitting regulations is of vital importance to in situ leach operators and firms considering in situ leaching. This study describes (1) all recent restoration attempts at commercial in situ leaching operations, (2) restoration costs reported by the industry, (3) empirical equations that predict the amount of groundwater flushing required to meet the current restoration criteria, and (4) in situ uranium permit requirements for the States of Texas, Wyoming, New Mexico, Utah, Montana, Colorado, and South Dakota, and Federal requirements

Ex situ bioremediation of a soil contaminated by mazut (heavy residual fuel oil)--a field experiment.

Science.gov (United States)

Beškoski, Vladimir P; Gojgić-Cvijović, Gordana; Milić, Jelena; Ilić, Mila; Miletić, Srdjan; Solević, Tatjana; Vrvić, Miroslav M

2011-03-01

Mazut (heavy residual fuel oil)-polluted soil was exposed to bioremediation in an ex situ field-scale (600 m(3)) study. Re-inoculation was performed periodically with biomasses of microbial consortia isolated from the mazut-contaminated soil. Biostimulation was conducted by adding nutritional elements (N, P and K). The biopile (depth 0.4m) was comprised of mechanically mixed polluted soil with softwood sawdust and crude river sand. Aeration was improved by systematic mixing. The biopile was protected from direct external influences by a polyethylene cover. Part (10 m(3)) of the material prepared for bioremediation was set aside uninoculated, and maintained as an untreated control pile (CP). Biostimulation and re-inoculation with zymogenous microorganisms increased the number of hydrocarbon degraders after 50 d by more than 20 times in the treated soil. During the 5 months, the total petroleum hydrocarbon (TPH) content of the contaminated soil was reduced to 6% of the initial value, from 5.2 to 0.3 g kg(-1) dry matter, while TPH reduced to only 90% of the initial value in the CP. After 150 d there were 96%, 97% and 83% reductions for the aliphatic, aromatic, and nitrogen-sulphur-oxygen and asphaltene fractions, respectively. The isoprenoids, pristane and phytane, were more than 55% biodegraded, which indicated that they are not suitable biomarkers for following bioremediation. According to the available data, this is the first field-scale study of the bioremediation of mazut and mazut sediment-polluted soil, and the efficiency achieved was far above that described in the literature to date for heavy fuel oil. Copyright © 2011 Elsevier Ltd. All rights reserved.

In situ gamma-ray spectrometric measurements of uranium in phosphates soil

International Nuclear Information System (INIS)

Lavi, N.; Ne'eman, E.; Brenner, S.; Haquin, G.; Nir-El, Y.

1997-01-01

Abstract Radioactivity concentration of 238 U in a phosphate ores quarry was measured in situ. Independently, soil samples collected in the site were measured in the laboratory. It was disclosed that radon emanation from the soil lowers in situ results that are derived from radon daughters. Uranium concentration was found to be 121.6±1.9 mg kg -1 (authors)

Resource impact evaluation of in-situ uranium groundwater restoration

International Nuclear Information System (INIS)

Charbeneau, R.J.; Rohlich, G.A.

1981-11-01

The purpose of this study was to determine the impact of restoration on the groundwater following in-situ uranium solution mining in South Texas. Restoration is necessary in order to reduce the amounts of undesired chemical constituents left in solution after mining operations have ceased, and thus return the groundwater to a quality consistent with pre-mining use and potential use. Various restoration strategies have been proposed and are discussed. Of interest are the hydrologic, environmental, social, and economic impacts of these restoration alternatives. Much of the discussion concerning groundwater restoration is based on the use of an ammonium carbonate-bicarbonate leach solution in the mining process. This has been the principal leach solution used during the early period of mining in South Texas. Recently, because of apparent difficulties in restoring ammonium to proposed or required levels, many of the companies have changed to the use of other leach solutions. Because little is known about restoration with these other leach solutions they have not been specifically addressed in this report. Likewise, we have not addressed the question of the fate of heavy metals. Following a summary of the development of South Texas in-situ mining in Chapter Two, Chapter Three describes the surface and groundwater resources of the uranium mining district. Chapter Four addresses the economics of water use, and Chapter Five is concerned with regulation of the in-situ uranium industry in Texas. A discussion of groundwater restoration alternatives and impacts is presented in Chapter Six. Chapter Seven contains a summary and a discussion, and conclusions derived from this study. Two case histories are presented in Appendices A and B

Bioremediation of soils

International Nuclear Information System (INIS)

Woodward, D.

1991-01-01

Bioremediation of hydrocarbon contaminated soils has evolved from the refinery land treatment units of thirty years ago to the modern slurry reactors of today. Modifications in the process include engineering controls designed to prevent the migration of hydrocarbons into the unsaturated zone, the saturated zone and groundwater, and the atmosphere. Engineering innovations in the area of composting and bioaugmentation that have focused on further process control and the acceleration of the treatment process will form the basis for future improvements in bioremediation technology. Case studies for established methods that have survived this development process and continue to be used as cost effective biological treatments like engineered land farms, soil heap treatment and in situ treatment will be discussed

A study on prediction of uranium concentration in pregnant solution from in-situ leaching

International Nuclear Information System (INIS)

Yi Weiping; Zhou Quan; Yu Yunzhen; Wang Shude; Yang Yihan; Lei Qifeng

2005-01-01

The modeling course on prediction of uranium concentration in pregnant solution from in-situ leaching of uranium is described, a mathematical model based on grey system theory is put forward, and a set of computer application software is correspondingly developed. (authors)

Aquifer restoration at uranium in situ leach sites

International Nuclear Information System (INIS)

Anastasi, F.S.; Williams, R.E.

1985-01-01

In situ mining of uranium involves injection of a leaching solution (lixiviant) into an ore-bearing aquifer. Frequently, the ground water in the mined aquifer is a domestic or livestock water supply. As the lixiviant migrates through the ore body, uranium and various associated elements such as arsenic, selenium, molybdenum, vanadium and radium-226 are mobilized in the ground water. Aquifer restoration after in situ mining is not fully understood. Several methods have been developed to restore mined aquifers to pre-mining (baseline) quality. Commonly used methods include ground water sweeping, clean water injection, and treatment by ion exchange and reverse osmosis technologies. Ammonium carbonate lixiviant was used at one RandD in situ mine. Attempts were made to restore the aquifer using a variety of methods. Efforts were successful in reducing concentrations of the majority of contaminants to baseline levels. Concentrations of certain parameters, however, remained at levels above baseline six months after restoration ceased. Relatively large quantities of ground water were processed in the restoration attempt considering the small size of the project (1.25 acre). More thorough characterization of the hydrogeology of the site may have enhanced the effectiveness of restoration and reduced potential environmental impacts associated with the project. This paper presents some of the findings of a research project conducted by the Mineral Resources Waste Management Team at the University of Idaho in Moscow, Idaho. Views contained herein do not reflect U.S. Nuclear Regulatory Commission policy

Microbial Communities in Contaminated Sediments, Associated with Bioremediation of Uranium to Submicromolar Levels▿

Science.gov (United States)

Cardenas, Erick; Wu, Wei-Min; Leigh, Mary Beth; Carley, Jack; Carroll, Sue; Gentry, Terry; Luo, Jian; Watson, David; Gu, Baohua; Ginder-Vogel, Matthew; Kitanidis, Peter K.; Jardine, Philip M.; Zhou, Jizhong; Criddle, Craig S.; Marsh, Terence L.; Tiedje, James M.

2008-01-01

Microbial enumeration, 16S rRNA gene clone libraries, and chemical analysis were used to evaluate the in situ biological reduction and immobilization of uranium(VI) in a long-term experiment (more than 2 years) conducted at a highly uranium-contaminated site (up to 60 mg/liter and 800 mg/kg solids) of the U.S. Department of Energy in Oak Ridge, TN. Bioreduction was achieved by conditioning groundwater above ground and then stimulating growth of denitrifying, Fe(III)-reducing, and sulfate-reducing bacteria in situ through weekly injection of ethanol into the subsurface. After nearly 2 years of intermittent injection of ethanol, aqueous U levels fell below the U.S. Environmental Protection Agency maximum contaminant level for drinking water and groundwater (reducers were detected, including Desulfovibrio, Geobacter, Anaeromyxobacter, Desulfosporosinus, and Acidovorax spp. The predominant sulfate-reducing bacterial species were Desulfovibrio spp., while the iron reducers were represented by Ferribacterium spp. and Geothrix spp. Diversity-based clustering revealed differences between treated and untreated zones and also within samples of the treated area. Spatial differences in community structure within the treatment zone were likely related to the hydraulic pathway and to electron donor metabolism during biostimulation. PMID:18456853

Functional environmental proteomics: elucidating the role of a c-type cytochrome abundant during uranium bioremediation.

Science.gov (United States)

Yun, Jiae; Malvankar, Nikhil S; Ueki, Toshiyuki; Lovley, Derek R

2016-02-01

Studies with pure cultures of dissimilatory metal-reducing microorganisms have demonstrated that outer-surface c-type cytochromes are important electron transfer agents for the reduction of metals, but previous environmental proteomic studies have typically not recovered cytochrome sequences from subsurface environments in which metal reduction is important. Gel-separation, heme-staining and mass spectrometry of proteins in groundwater from in situ uranium bioremediation experiments identified a putative c-type cytochrome, designated Geobacter subsurface c-type cytochrome A (GscA), encoded within the genome of strain M18, a Geobacter isolate previously recovered from the site. Homologs of GscA were identified in the genomes of other Geobacter isolates in the phylogenetic cluster known as subsurface clade 1, which predominates in a diversity of Fe(III)-reducing subsurface environments. Most of the gscA sequences recovered from groundwater genomic DNA clustered in a tight phylogenetic group closely related to strain M18. GscA was most abundant in groundwater samples in which Geobacter sp. predominated. Expression of gscA in a strain of Geobacter sulfurreducens that lacked the gene for the c-type cytochrome OmcS, thought to facilitate electron transfer from conductive pili to Fe(III) oxide, restored the capacity for Fe(III) oxide reduction. Atomic force microscopy provided evidence that GscA was associated with the pili. These results demonstrate that a c-type cytochrome with an apparent function similar to that of OmcS is abundant when Geobacter sp. are abundant in the subsurface, providing insight into the mechanisms for the growth of subsurface Geobacter sp. on Fe(III) oxide and suggesting an approach for functional analysis of other Geobacter proteins found in the subsurface.

Multi-coupling dynamic model and 3d simulation program for in-situ leaching of uranium mining

International Nuclear Information System (INIS)

Tan Kaixuan; Zeng Sheng; Sang Xiao; Sun Bing

2010-01-01

The in-situ leaching of uranium mining is a very complicated non-linear dynamic system, which involves couplings and positive/negative feedback among many factors and processes. A comprehensive, coupled multi-factors and processes dynamic model and simulation method was established to study the in-situ leaching of uranium mining. The model accounts for most coupling among various processes as following: (1) rock texture mechanics and its evolution, (2)the incremental stress rheology of rock deformation, (3) 3-D viscoelastic/ plastic multi-deformation processes, (4) hydrofracturing, (5) tensorial (anisotropic) fracture and rock permeability, (6) water-rock interactions and mass-transport (both advective and diffusive), (7) dissolution-induced chemical compaction, (8) multi-phase fluid flow. A 3-D simulation program was compiled based on Fortran and C++. An example illustrating the application of this model to simulating acidification, production and terminal stage of in situ leaching of uranium mining is presented for the some mine in Xinjiang, China. This model and program can be used for theoretical study, mine design, production management, the study of contaminant transport and restoration in groundwater of in-situ leaching of uranium mining. (authors)

Groundwater restoration of in-situ uranium mines

International Nuclear Information System (INIS)

Anon.

1994-01-01

In-situ leaching is a relatively new uranium production technology that is expected to account for a growing share of future output. Depending upon the leaching solution used, the process may have considerable impact on the ground water. Since restoration of ground water quality is required in most countries and since this restoration is by far the most costly aspect of reclamation of an in-situ mine, it is necessary to utilize a process that lends itself both to the efficiency of the leaching process and the restoration process. This article examines a number of techniques that may be used in the restoration efforts. These include: (1) groundwater sweep, (2) reverse osmosis, (3) chemical restoration, and (4) electrodialysis. The article also discusses disposal of the excess fluids used in the restoration process

Enhanced Uranium Immobilization and Reduction by Geobacter sulfurreducens Biofilms

Science.gov (United States)

Cologgi, Dena L.; Speers, Allison M.; Bullard, Blair A.; Kelly, Shelly D.

2014-01-01

Biofilms formed by dissimilatory metal reducers are of interest to develop permeable biobarriers for the immobilization of soluble contaminants such as uranium. Here we show that biofilms of the model uranium-reducing bacterium Geobacter sulfurreducens immobilized substantially more U(VI) than planktonic cells and did so for longer periods of time, reductively precipitating it to a mononuclear U(IV) phase involving carbon ligands. The biofilms also tolerated high and otherwise toxic concentrations (up to 5 mM) of uranium, consistent with a respiratory strategy that also protected the cells from uranium toxicity. The enhanced ability of the biofilms to immobilize uranium correlated only partially with the biofilm biomass and thickness and depended greatly on the area of the biofilm exposed to the soluble contaminant. In contrast, uranium reduction depended on the expression of Geobacter conductive pili and, to a lesser extent, on the presence of the c cytochrome OmcZ in the biofilm matrix. The results support a model in which the electroactive biofilm matrix immobilizes and reduces the uranium in the top stratum. This mechanism prevents the permeation and mineralization of uranium in the cell envelope, thereby preserving essential cellular functions and enhancing the catalytic capacity of Geobacter cells to reduce uranium. Hence, the biofilms provide cells with a physically and chemically protected environment for the sustained immobilization and reduction of uranium that is of interest for the development of improved strategies for the in situ bioremediation of environments impacted by uranium contamination. PMID:25128347

Diversity and characterization of sulfate-reducing bacteria in groundwater at a uranium mill tailings site

International Nuclear Information System (INIS)

Chang, Yun-Juan; Peacock, A D.; Long, Philip E.; Stephen, John R.; McKinley, James P.; Mcnaughton, Sarah J.; Hussain, A K M A.; Saxton, A M.; White, D C.

2000-01-01

Microbially mediated reduction and immobilization of U(VI) to U(TV) plays a role in both natural attenuation and accelerated bioremediation of uranium contaminated sites. To realize bioremediation potential and accurately predict natural attenuation, it is important to first understand the microbial diversity of such sites. In this paper, the distribution of sulfate-reducing bacteria (SRB) in contaminated groundwater associated with a uranium mill tailings disposal site at Shiprock, N.Mex,, was investigated. Two culture-independent analyses were employed: sequencing of clone libraries of PCR-amplified dissimilatory sulfite reductase (DSR) gene fragments and phospholipid fatty acid (PLFA) biomarker analysis. A remarkable diversity among the DSR sequences was revealed, including sequences from F-Proteobacteria, gram-positive organisms, and the Nitrospira division. PLFA analysis detected at least,52 different mid-chain-branched saturate PLFA and included a high proportion of 10me16:0, Desulfotomaculum and Desulfotomaculum-like sequences were the most dominant DSR genes detected. Those belonging to SRB within F-Proteobacteria were mainly recovered from low-uranium (less than or equal to 302 ppb) samples. One Desulfotomaculum like sequence cluster overwhelmingly dominated high-U (> 1,500 ppb) sites. Logistic regression showed a significant influence of uranium concentration over the dominance of this cluster of sequences (P= 0.0001), This strong association indicates that Desulfotomaculum has remarkable tolerance and adaptation to high levels of uranium and suggests the organism's possible involvement in natural attenuation of uranium. The in situ activity level of Desulfotomaculum in uranium-contaminated environments and its comparison to the activities of other SRB and other functional groups should be an important area for future research

Initial characterization of a highly contaminated high explosives outfall in preparation for in situ bioremediation

Energy Technology Data Exchange (ETDEWEB)

Betty A. Strietelmeier; Patrick J. Coyne; Patricia A. Leonard; W. Lamar Miller; Jerry R. Brian

1999-12-01

In situ bioremediation is a viable, cost-effective treatment for environmental contamination of many kinds. The feasibility of using biological techniques to remediate soils contaminated with high explosives (HE) requires laboratory evaluation before proceeding to a larger scale field operation. Laboratory investigations have been conducted at pilot scale which indicate that an anaerobic process could be successful at reducing levels of HE, primarily HMX, RDX and TNT, in contaminated soils. A field demonstration project has been designed to create an anaerobic environment for the degradation of HE materials. The first step in this project, initial characterization of the test area, was conducted and is the subject of this report. The levels of HE compounds found in the samples from the test area were higher than the EPA Method 8330 was able to extract without subsequent re-precipitation; therefore, a new method was developed using a superior extractant system. The test area sampling design was relatively simple as one might expect in an initial characterization. A total of 60 samples were each removed to a depth of 4 inches using a 1 inch diameter corer. The samples were spaced at relatively even intervals across a 20 foot cross-section through the middle of four 7-foot-long adjacent plots which are designed to be a part of an in situ bioremediation experiment. Duplicate cores were taken from each location for HE extraction and analysis in order to demonstrate and measure the heterogeneity of the contamination. Each soil sample was air dried and ball-milled to provide a homogeneous solid for extraction and analysis. Several samples had large consolidated pieces of what appeared to be solid HE. These were not ball-milled due to safety concerns, but were dissolved and the solutions were analyzed. The new extraction method was superior in that results obtained for several of the contaminants were up to 20 times those obtained with the EPA extraction method. The

Method for in situ or ex situ bioremediation of hexavalent chromium contaminated soils and/or groundwater

Science.gov (United States)

Turick, Charles E.; Apel, William W.

1997-10-28

A method of reducing the concentration of Cr(VI) in a liquid aqueous residue comprises the steps of providing anaerobic Cr(VI) reducing bacteria, mixing the liquid aqueous residue with a nutrient medium to form a mixture, and contacting the mixture with the anaerobic Cr(VI) reducing bacteria such that Cr(VI) is reduced to Cr(III). The anaerobic Cr(VI) reducing bacteria appear to be ubiquitous in soil and can be selected by collecting a soil sample, diluting the soil sample with a sterile diluent to form a diluted sample, mixing the diluted sample with an effective amount of a nutrient medium and an effective amount of Cr(VI) to form a mixture, and incubating the mixture in the substantial absence of oxygen such that growth of Cr(VI) sensitive microorganisms is inhibited and growth of the anaerobic Cr(VI) reducing bacteria is stimulated. A method of in situ bioremediation of Cr(VI) contaminated soil and/or groundwater is also disclosed.

Entomoremediation - A Novel In-Situ Bioremediation Approach ...

African Journals Online (AJOL)

In this paper entomoremediation as a novel concept was critically projected as a bioremediation technique that needs to be harnessed in line with global realities of involving organisms like microorganisms and earthworms in soil decontamination. Entomoremediation is defined as a type of remediation in which insects are ...

Monitoring Genetic and Metabolic Potential for In-Site Bioremediation: Mass Spectrometry

International Nuclear Information System (INIS)

Buchanan, M.V.

2000-01-01

A number of DOE sites are contaminated with mixtures of dense non-aqueous phase liquids (DNAPLs) such as carbon tetrachloride, chloroform, perchloroethylene, and trichloroethylene. At many of these sites, in situ microbial bioremediation is an attractive strategy for cleanup, since it has the potential to degrade DNAPLs in situ without the need for pump-and-treat or soil removal procedures, and without producing toxic byproducts. A rapid screening method to determine broad range metabolic and genetic potential for contaminant degradation would greatly reduce the cost and time involved in assessment for in situ bioremediation, as well as for monitoring ongoing bioremediation treatment. The objective of this project was the development of mass-spectrometry-based methods to screen for genetic potential for both assessment and monitoring of in situ bioremediation of DNAPLs. These methods were designed to provide more robust and routine methods for DNA-based characterization of the genetic potential of subsurface microbes for degrading pollutants. Specifically, we sought to (1) Develop gene probes that yield information equivalent to conventional probes, but in a smaller size that is more amenable to mass spectrometric detection, (2) Pursue improvements to matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS) methodology in order to allow its more general application to gene probe detection, and (3) Increase the throughput of microbial characterization by integrating gene probe preparation, purification, and MALDI-MS analysis

Quantification of the effect of in-situ generated uranium metal on the experimentally determined O/U ratio of a sintered uranium dioxide fuel pellet

International Nuclear Information System (INIS)

Narasimha Murty, B.; Bharati Misra, U.; Yadav, R.B.; Srivastava, R.K.

2005-01-01

This paper describes quantitatively the effect of in-situ generated uranium metal (that could be formed due to the conducive manufacturing conditions) in a sintered uranium dioxide fuel pellet on the experimentally determined O/U ratio using analytical methods involving dissolution of the pellet material. To quantify the effect of in-situ generated uranium metal in the fuel pellet, a mathematical expression is derived for the actual O/U ratio in terms of the O/U ratio as determined by an experiment involving dissolution of the material and the quantity of uranium metal present in the uranium dioxide pellet. The utility of this derived mathematical expression is demonstrated by tabulating the calculated actual O/U ratios for varying amounts of uranium metal (from 5 to 95% in 5% intervals) and different O/U ratio values (from 2.001 to 2.015 in 0.001 intervals). This paper brings out the necessity of care to be exercised while interpreting the experimentally determined O/U ratio and emphasizes the fact that it is always safer to produce the nuclear fuel with oxygen to uranium ratios well below the specified maximum limit of 2.015. (author)

In situ aquifer bioremediation of organics including cyanide and carbon disulfide

International Nuclear Information System (INIS)

Abou-Rizk, J.A.M.; Leavitt, M.E.; Graves, D.A.

1995-01-01

Low levels (< 1 mg/L) of acetone, cyanide, phenol, naphthalene, 2-methylnaphthalene, and carbon disulfide from an inactive industrial landfill were found above background levels in a shallow aquifer at an eastern coastal site. In situ biodegradation was evaluated for treatment of these contaminants. Two soil samples and three groundwater samples were taken from the site for a laboratory bioassessment and a biotreatability test. The positive results of the bioassessment suggested moving forward with biotreatability testing. Biotreatability test results indicated suitable site conditions for bioremediation and that all the contaminants of concern at the site could be biodegraded to nondetect or very low levels (< 50 microg/L) with oxygen only; i.e., addition of nutrients was not required. Pilot-scale testing was undertaken on site to provide information for full-scale design, including oxygen requirements and air injection well spacing. This report describes the approach, the results, and their impact on the full-scale remediation system

Bioremediation of uranium contaminated soils and wastes

International Nuclear Information System (INIS)

Francis, A.J.

1998-01-01

Contamination of soils, water, and sediments by radionuclides and toxic metals from uranium mill tailings, nuclear fuel manufacturing and nuclear weapons production is a major concern. Studies of the mechanisms of biotransformation of uranium and toxic metals under various microbial process conditions has resulted in the development of two treatment processes: (1) stabilization of uranium and toxic metals with reduction in waste volume and (2) removal and recovery of uranium and toxic metals from wastes and contaminated soils. Stabilization of uranium and toxic metals in wastes is accomplished by exploiting the unique metabolic capabilities of the anaerobic bacterium, Clostridium sp. The radionuclides and toxic metals are solubilized by the bacteria directly by enzymatic reductive dissolution, or indirectly due to the production of organic acid metabolites. The radionuclides and toxic metals released into solution are immobilized by enzymatic reductive precipitation, biosorption and redistribution with stable mineral phases in the waste. Non-hazardous bulk components of the waste volume. In the second process uranium and toxic metals are removed from wastes or contaminated soils by extracting with the complexing agent citric acid. The citric-acid extract is subjected to biodegradation to recover the toxic metals, followed by photochemical degradation of the uranium citrate complex which is recalcitrant to biodegradation. The toxic metals and uranium are recovered in separate fractions for recycling or for disposal. The use of combined chemical and microbiological treatment process is more efficient than present methods and should result in considerable savings in clean-up and disposal costs

Principles of Bioremediation Assessment

Science.gov (United States)

Madsen, E. L.

2001-12-01

Although microorganisms have successfully and spontaneously maintained the biosphere since its inception, industrialized societies now produce undesirable chemical compounds at rates that outpace naturally occurring microbial detoxification processes. This presentation provides an overview of both the complexities of contaminated sites and methodological limitations in environmental microbiology that impede the documentation of biodegradation processes in the field. An essential step toward attaining reliable bioremediation technologies is the development of criteria which prove that microorganisms in contaminated field sites are truly active in metabolizing contaminants of interest. These criteria, which rely upon genetic, biochemical, physiological, and ecological principles and apply to both in situ and ex situ bioremediation strategies include: (i) internal conservative tracers; (ii) added conservative tracers; (iii) added radioactive tracers; (iv) added isotopic tracers; (v) stable isotopic fractionation patterns; (vi) detection of intermediary metabolites; (vii) replicated field plots; (viii) microbial metabolic adaptation; (ix) molecular biological indicators; (x) gradients of coreactants and/or products; (xi) in situ rates of respiration; (xii) mass balances of contaminants, coreactants, and products; and (xiii) computer modeling that incorporates transport and reactive stoichiometries of electron donors and acceptors. The ideal goal is achieving a quantitative understanding of the geochemistry, hydrogeology, and physiology of complex real-world systems.

Use of a mathematical model for prediction of optimum feeding strategies for in situ bioremediation

International Nuclear Information System (INIS)

Shouche, M.; Petersen, J.N.

1992-05-01

Liquid wastes containing radioactive, hazardous, and regulated chemicals have been generated throughout the 40+ years of operations at the US Department of Energy (DOE) Hanford site. Some of these wastes were discharged to the soil column and many of the waste components, including nitrate, carbon tetrachloride (CCL 4 ), and several radionuclides, have been detected in the Hanford groundwater. Current DOE policy prohibits the disposal of the contaminated liquids directly to the environment, and remediation of the existing contaminated groundwaters may be required. In-situ bioremediation is one technology currently being developed at the Hanford to meet the need for cost effective technologies to clean groundwater contaminated with CCL 4 , nitrate, and other organic and inorganic contaminants. This paper focuses on the latest results of an on-going effort to develop effective in-situ remediation strategies through the use of predictive simulations. In particular, strategies for nutrient injection are developed which minimize biomass accumulation within the flow field and thus extend the life of injection wells

Bioremediation of oil-contaminated sites

Energy Technology Data Exchange (ETDEWEB)

Balba, T. [Conestoga-Rovers and Associates, Calgary, AB (Canada)

2003-07-01

One of the most prevalent contaminants in subsurface soil and groundwater are petroleum hydrocarbons. This paper presented bioremediation of petroleum hydrocarbons as one of the most promising treatment technologies. Petroleum hydrocarbons are categorized into four simple fractions: saturates, aromatics, resins, and asphaltenes. Bioremediation refers to the treatment process whereby contaminants are metabolized into less toxic or nontoxic compounds by naturally occurring organisms. The various strategies include: use of constitutive enzymes, enzyme induction, co-metabolism, transfer of plasmids coding for certain metabolic pathways, and production of biosurfactants to enhance bioavailability of hydrophobic compounds. Three case studies were presented: (1) bioremediation of heavy oils in soil at a locomotive maintenance yard in California, involving a multi-step laboratory treatability study followed by a field demonstration achieving up to 94 per cent removal of TPH in less than 16 weeks, (2) bioremediation of light oils in soil at an oil refinery in Germany where a dual process was applied (excavation and in-situ treatment), achieving an 84 per cent reduction within 24 weeks, and (3) bioremediation of oil-contaminated desert soil in Kuwait which involved landfarming, composting piles, and bioventing soil piles, achieving an 80 per cent reduction within 12 months. 7 refs., 1 tab., 3 figs.

Best practice in situ recovery uranium mining in Australia

International Nuclear Information System (INIS)

Lambert, I.B.; McKay, A.D.; Carson, L.J.

2010-01-01

The Australian Government policy is to ensure that uranium mining, milling and rehabilitation is based on world best practice standards. A best practice guide for in situ recovery (ISR) uranium mining has been developed to communicate the Australian Government's expectations with a view to achieving greater certainty that ISR mining projects meet Australian Government policy and consistency in the assessment of ISR mine proposals within multiple government regulatory processes. The guide focuses on the main perceived risks; impacts on groundwaters, disposal of mining residues, and radiation protection. World best practice does not amount to a universal template for ISR mining because the characteristics of individual ore bodies determine the best practice. (author)

Two US EPA bioremediation field initiative studies: Evaluation of in-situ bioventing

International Nuclear Information System (INIS)

Sayles, G.D.; Brenner, R.C.; Hinchee, R.E.; Vogel, C.M.; Miller, R.N.

1992-01-01

Bioventing is the process of supplying oxygen in-situ to oxygen-deprived soil microbes by forcing air through contaminated soil at low air flow rates. Unlike soil venting or soil vacuum extraction technologies, bioventing attempts to stimulate biodegradative activity while minimizing stripping of volatile organics. The process destroys the toxic compounds in the ground. Bioventing technology is especially valuable for treating contaminated soils in areas where structures and utilities cannot be disturbed because the equipment needed (air injection/withdrawal wells, air blower, and soil gas monitoring wells) is relatively non-invasive. The US EPA Risk Reduction Engineering Laboratory, with resources from the US EPA Bioremediation Field Initiative, began two parallel 2-year field studies of in-situ of 1991 in collaboration with the US Air Force. The field sites are located at Eielson Air Force Base (AFB) near Fairbanks, Alaska, and Hill AFB near Salt Lake City, Utah. Each site has jet fuel JP-4 contaminated unsaturated soil where a spill has occurred in association with a fuel distribution network. With the pilot-scale experience gained in these studies and others, bioventing should be available in the very near future as an inexpensive, unobtrusive means of treating large quantities of organically contaminated soils. 5 figs

Efficiency of consortium for in-situ bioremediation and CO2 evolution method of refines petroleum oil in microcosms study

OpenAIRE

Dutta, Shreyasri; Singh, Padma

2017-01-01

An in-situ bioremediation study was conducted in a laboratory by using mixed microbial consortium. An indigenous microbial consortium was developed by assemble of two Pseudomonas spp. and two Aspergillus spp. which were isolated from various oil contaminated sites of India. The laboratory feasibility study was conducted in a 225 m2 block. Six treatment options-Oil alone, Oil+Best remediater, Oil+Bacterial consortium, Oil+Fungal consortium, Oil+Mixed microbial consortium, Oil+Indigenous microf...

Field test for treatment verification of an in-situ enhanced bioremediation study

International Nuclear Information System (INIS)

Taur, C.K.; Chang, S.C.

1995-01-01

Due to a leakage from a 12-inch pressurized diesel steel pipe four years ago, an area of approximately 30,000 square meters was contaminated. A pilot study applying the technology of in-situ enhanced bioremediation was conducted. In the study, a field test kit and on-site monitoring equipment were applied for site characterization and treatment verification. Physically, the enhanced bioremediation study consisted of an air extraction and air supply system, and a nutrition supply network. Certain consistent sampling methodology was employed. Progress was verified by daily monitoring and monthly verification. The objective of this study was to evaluate the capabilities of indigenous microorganisms to biodegrade the petroleum hydrocarbons with provision of oxygen and nutrients. Nine extraction wells and eight air sparging wells were installed. The air sparging wells injected the air into geoformation and the extraction wells provided the underground air circulation. The soil samples were obtained monthly for treatment verification by a Minuteman drilling machine with 2.5-foot-long hollow-stem augers. The samples were analyzed on site for TPH-diesel concentration by a field test kit manufactured by HNU-Hanby, Houston, Texas. The analytical results from the field test kit were compared with the results from an environmental laboratory. The TVPH concentrations of the air extracted from the vadose zone by a vacuum blower and the extraction wells were routinely monitored by a Foxboro FID and Cosmos XP-311A combustible air detector. The daily monitoring of TVPH concentrations provided the reliable data for assessing the remedial progress

Quantifying Temporal Autocorrelations for the Expression of Geobacter species mRNA Gene Transcripts at Variable Ammonium Levels during in situ U(VI) Bioremediation

Science.gov (United States)

Mouser, P. J.

2010-12-01

In order to develop decision-making tools for the prediction and optimization of subsurface bioremediation strategies, we must be able to link the molecular-scale activity of microorganisms involved in remediation processes with biogeochemical processes observed at the field-scale. This requires the ability to quantify changes in the in situ metabolic condition of dominant microbes and associate these changes to fluctuations in nutrient levels throughout the bioremediation process. It also necessitates a need to understand the spatiotemporal variability of the molecular-scale information to develop meaningful parameters and constraint ranges in complex bio-physio-chemical models. The expression of three Geobacter species genes (ammonium transporter (amtB), nitrogen fixation (nifD), and a housekeeping gene (recA)) were tracked at two monitoring locations that differed significantly in ammonium (NH4+) concentrations during a field-scale experiment where acetate was injected into the subsurface to simulate Geobacteraceae in a uranium-contaminated aquifer. Analysis of amtB and nifD mRNA transcript levels indicated that NH4+ was the primary form of fixed nitrogen during bioremediation. Overall expression levels of amtB were on average 8-fold higher at NH4+ concentrations of 300 μM or more than at lower NH4+ levels (average 60 μM). The degree of temporal correlation in Geobacter species mRNA expression levels was calculated at both locations using autocorrelation methods that describe the relationship between sample semi-variance and time lag. At the monitoring location with lower NH4+, a temporal correlation lag of 8 days was observed for both amtB and nifD transcript patterns. At the location where higher NH4+ levels were observed, no discernable temporal correlation lag above the sampling frequency (approximately every 2 days) was observed for amtB or nifD transcript fluctuations. Autocorrelation trends in recA expression levels at both locations indicated that

The computerized semi-quantitative comprehensive identification-evaluation model for the large-sized in-situ leachable sandstone type uranium deposits in Northern Xinjiang, China

Energy Technology Data Exchange (ETDEWEB)

Zhengbang, Wang; Mingkuan, Qin; Ruiquan, Zhao; Shenghuang, Tang [Beijing Research Inst. of Uranium Geology, CNNC (China); Baoqun, Wang; Shuangxing, Lin [Geo-prospecting Team No. 216, CNNC (China)

2001-08-01

The process of establishment of the model includes following steps: (1) Systematically studying a known typical in-situ leachable sandstone type uranium deposit--Deposit No. 512 in Yili basin, analyzing its controlling factors and establishing its metallogenetic model; (2) Establishing the metallogenetic models of this type of uranium deposit and uranium-bearing area on the basis of comparison study on the deposit No. 512 with the same type uranium deposits in the world; (3) Creating the computerized semi-quantitative comprehensive identification-evaluation model for the large-sized in-situ leachable sandstone type uranium deposits in northern Xinjiang; (4) Determining the standards of giving a evaluation-mark for each controlling factor of in-situ leachable sandstone type uranium deposit and uranium-bearing area; (5) Evaluating uranium potential and prospect of the unknown objective target.

The computerized semi-quantitative comprehensive identification-evaluation model for the large-sized in-situ leachable sandstone type uranium deposits in Northern Xinjiang, China

International Nuclear Information System (INIS)

Wang Zhengbang; Qin Mingkuan; Zhao Ruiquan; Tang Shenghuang; Wang Baoqun; Lin Shuangxing

2001-01-01

The process of establishment of the model includes following steps: (1) Systematically studying a known typical in-situ leachable sandstone type uranium deposit--Deposit No. 512 in Yili basin, analyzing its controlling factors and establishing its metallogenetic model; (2) Establishing the metallogenetic models of this type of uranium deposit and uranium-bearing area on the basis of comparison study on the deposit No. 512 with the same type uranium deposits in the world; (3) Creating the computerized semi-quantitative comprehensive identification-evaluation model for the large-sized in-situ leachable sandstone type uranium deposits in northern Xinjiang; (4) Determining the standards of giving a evaluation-mark for each controlling factor of in-situ leachable sandstone type uranium deposit and uranium-bearing area; (5) Evaluating uranium potential and prospect of the unknown objective target

Ross In Situ Uranium Recovery Project NESHAP Subpart W Construction Approval

Science.gov (United States)

On May 5, 2015, EPA issued a Construction Approval under the National Emission Standards for Hazardous Air Pollutants (NESHAPs) at 40 CFR Part 61, subpart W, to Strata Energy, Inc., for their Ross In Situ Recovery (ISR) Uranium Project in Crook County, WY.

Initial assessment of intrinsic and assisted bioremediation potential for diesel fuel impacted soils at Eureka, NWT

International Nuclear Information System (INIS)

Wilson, J. J.; Yeske, B.; Lee, D.; Nahir, M.

1999-01-01

Two diesel fuel-impacted soil columns prepared to simulate in situ conditions for assessing intrinsic bioremediation were studied. The samples were from Eureka in the Northwest Territories. Two soil jars that were mixed periodically to simulate the ex situ land treatment bioremediation option, were also part of the treatability study. Results strongly suggest that bioremediation at Eureka is a viable option, although the slow rate of biodegradation and the short operating season will necessitate treatment over several years to achieve the remediation endpoint. The intrinsic bioremediation process can be accelerated using periodic addition of a water soluble nitrogen fertilizer, as shown by the nitrogen-amended soil column test. Ex situ bioremediation also appears to be possible judged by the response of the natural bacterial population to periodic mixing and oxygen uptake at 5 degrees C. The principal challenge will be to adequately mix the soil at the surface and to prevent it from drying out. The addition of organic bulking material may be required. 1 ref., 3 tabs., 4 figs

Treatment of a mud pit by bioremediation.

Science.gov (United States)

Avdalović, Jelena; Đurić, Aleksandra; Miletić, Srdjan; Ilić, Mila; Milić, Jelena; Vrvić, Miroslav M

2016-08-01

The mud generated from oil and natural gas drilling, presents a considerable ecological problem. There are still insufficient remedies for the removal and minimization of these very stable emulsions. Existing technologies that are in use, more or less successfully, treat about 20% of generated waste drilling mud, while the rest is temporarily deposited in so-called mud pits. This study investigated in situ bioremediation of a mud pit. The bioremediation technology used in this case was based on the use of naturally occurring microorganisms, isolated from the contaminated site, which were capable of using the contaminating substances as nutrients. The bioremediation was stimulated through repeated inoculation with a zymogenous microbial consortium, along with mixing, watering and biostimulation. Application of these bioremediation techniques reduced the concentration of total petroleum hydrocarbons from 32.2 to 1.5 g kg(-1) (95% degradation) during six months of treatment. © The Author(s) 2016.

Elucidating the fate of a mixed toluene, DHM, methanol, and i-propanol plume during in situ bioremediation

Science.gov (United States)

Verardo, E.; Atteia, O.; Prommer, H.

2017-06-01

Organic pollutants such as solvents or petroleum products are widespread contaminants in soil and groundwater systems. In-situ bioremediation is a commonly used remediation technology to clean up the subsurface to eliminate the risks of toxic substances to reach potential receptors in surface waters or drinking water wells. This study discusses the development of a subsurface model to analyse the performance of an actively operating field-scale enhanced bioremediation scheme. The study site was affected by a mixed toluene, dihydromyrcenol (DHM), methanol, and i-propanol plume. A high-resolution, time-series of data was used to constrain the model development and calibration. The analysis shows that the observed failure of the treatment system is linked to an inefficient oxygen injection pattern. Moreover, the model simulations also suggest that additional contaminant spillages have occurred in 2012. Those additional spillages and their associated additional oxygen demand resulted in a significant increase in contaminant fluxes that remained untreated. The study emphasises the important role that reactive transport modelling can play in data analyses and for enhancing remediation efficiency.

In situ bioremediation: A network model of diffusion and flow in granular porous media

Energy Technology Data Exchange (ETDEWEB)

Griffiths, S.K.; Nilson, R.H.; Bradshaw, R.W.

1997-04-01

In situ bioremediation is a potentially expedient, permanent and cost- effective means of waste site decontamination. However, permeability reductions due to the transport and deposition of native fines or due to excessive microorganism populations may severely inhibit the injection of supplemental oxygen in the contamination zone. To help understand this phenomenon, we have developed a micro-mechanical network model of flow, diffusion and particle transport in granular porous materials. The model differs from most similar models in that the network is defined by particle positions in a numerically-generated particle array. The model is thus widely applicable to computing effective transport properties for both ordered and realistic random porous media. A laboratory-scale apparatus to measure permeability reductions has also been designed, built and tested.

Study on U-Ra equilibrium coefficient of the in-situ leaching sandstone-type uranium deposits: A case study of Qianjiadian uranium deposit

International Nuclear Information System (INIS)

Xia Yuliang; Xiu Qunye; Han Jun; Li Linqiang; Zheng Jiwei

2013-01-01

This paper investigated the U-Ra equilibrium coefficient (K-p) of mineralized sandstone and mudstone, and unmineralized sandstone and mudstone for the in-situ leaching sandstone-type uranium deposits. It is surprised that all of the mineralized sandstone and mudstone are both relatively to be partial to uranium, but all of the unmineralized sandstone and mudstone are both relatively to be partial to radium. Meanwhile the uranium in mineralized mudstone is relatively richer than that in mineralized sandstone, and the radium in unmineralized mudstone is relatively richer than that in unmineralized sandstone. It is suggested that mudstones were permeable at the uranium mineralized phase and the unmineralized mudstone and sandstone could serve as important mineralized uranium source. (authors)

Recovering uranium from coal in-situ. Final report, February 1980-July 1981

International Nuclear Information System (INIS)

1981-01-01

In Situ Technology, Inc., ''InTech,'' has designed a new process for recovery of uranium from coal in situ. Prime objectives of the program reported herein are to reduce two uncertainties related to eventual commercialization of the process. The first uncertainty concerns appropriate field sites and their potential. The work involved laboratory tests and analysis of field samples, burning the samples to ash and leaching uranium from residual ash at laboratory scale, and burning the samples to ash and leaching uranium from residual ash at pilot plant scale. Laboratory and pilot plant tests were designed to simulate significant elements of the underground process. Field samples from New Mexico averaged 0.061% U 3 O 8 and from North Dakota 0.058% of U 3 O 8 in the coal, both on a dry basis. Phase I laboratory tests on New Mexico field samples were successfully conducted with no difficulties in reducing uraniferous coal to ash. Leaching tests resulted in uranium recoveries to 77.9% with acid leach and to 56% with alkaline leach. Phase II laboratory and pilot plant scale tests were successfully conducted on North Dakota field samples, but required supplemental fuel and/or enrichment for reducing uraniferous coal to ash. Acid leaching of residual ash resulted in uranium recoveries to 83.8%. Acid consumption was 71.0 pounds per ton during pilot plant scale leaching tests. The overall analysis and test program is considered to be highly successful and resulted in significant reduction of the uncertainties for eventual commercialization of the process. 3 refs

Report on the feasibility of the in situ radiometric determination of uranium grade in Witwatersrand gold and uranium mines

International Nuclear Information System (INIS)

Smit, C.J.B.; Wesolinski, E.S.; Corner, B.

1982-08-01

The chip-sampling technique currently employed by the South African gold and uranium-mining industry, for the prediction of face grade, has several drawbacks, namely: 1) it is labour-intensive; 2) sample volumes are often unrepresentative and prone to human error; and 3) the uranium mineralisation may be very erratic along the reef. In situ radiometric assaying for uranium along the reef, on the other hand, is a rapid, essentially one-man operation, enabling a much larger and hence a more representative sample volume to be measured. The high radiometric background inherent in any uranium mine necessitates some form of high-density shielding in order to facilitate quantitative in situ assaying. This report, therefore, briefly outlines the origin, nature, detection and shielding of gamma rays. Results obtained with a frontally shielded total-count instrument showed that radiometric estimates of uranium grade are comparable to those obtained by batch mining and can be used for the prediction of face grades, provided that the ore is in radiometric equilibrium and that thorium and potassium are either not present, or vary sympathetically with the uranium grade. Spectral analysis showed, however, that these circumstances will also permit the use of a collimated (side-shielded) detector of acceptable weight, provided that only the low-energy portion of the spectrum is measured. The advantages of a collimated detector over a frontally shielded detector are also noteworthy, viz.: 1) only one reading is taken per sample point rather than two, as is the case with the frontally shielded system, thus improving counting statistics; and 2) the shielding is permanently fixed to the detector. Comprehensive design considerations for a compact, portable instrument are suggested and methods for determining background radiation as applicable to a collimated detector are described

Uranium redox transition pathways in acetate-amended sediments

Science.gov (United States)

Bargar, John R.; Williams, Kenneth H.; Campbell, Kate M.; Long, Philip E.; Stubbs, Joanne E.; Suvorova, Elenal I.; Lezama-Pacheco, Juan S.; Alessi, Daniel S.; Stylo, Malgorzata; Webb, Samuel M.; Davis, James A.; Giammar, Daniel E.; Blue, Lisa Y.; Bernier-Latmani, Rizlan

2013-01-01

Redox transitions of uranium [from U(VI) to U(IV)] in low-temperature sediments govern the mobility of uranium in the environment and the accumulation of uranium in ore bodies, and inform our understanding of Earth’s geochemical history. The molecular-scale mechanistic pathways of these transitions determine the U(IV) products formed, thus influencing uranium isotope fractionation, reoxidation, and transport in sediments. Studies that improve our understanding of these pathways have the potential to substantially advance process understanding across a number of earth sciences disciplines. Detailed mechanistic information regarding uranium redox transitions in field sediments is largely nonexistent, owing to the difficulty of directly observing molecular-scale processes in the subsurface and the compositional/physical complexity of subsurface systems. Here, we present results from an in situ study of uranium redox transitions occurring in aquifer sediments under sulfate-reducing conditions. Based on molecular-scale spectroscopic, pore-scale geochemical, and macroscale aqueous evidence, we propose a biotic–abiotic transition pathway in which biomass-hosted mackinawite (FeS) is an electron source to reduce U(VI) to U(IV), which subsequently reacts with biomass to produce monomeric U(IV) species. A species resembling nanoscale uraninite is also present, implying the operation of at least two redox transition pathways. The presence of multiple pathways in low-temperature sediments unifies apparently contrasting prior observations and helps to explain sustained uranium reduction under disparate biogeochemical conditions. These findings have direct implications for our understanding of uranium bioremediation, ore formation, and global geochemical processes.

Biotechnology for uranium extraction and environmental control

International Nuclear Information System (INIS)

Natarajan, K.A.

2012-01-01

India is looking forward to augmenting mining and extraction of uranium mineral for its nuclear energy needs. Being a radio-active mineral, mining and processing of uranium ore deposits need be carried out in an environmentally acceptable fashion. In this respect, a biotechnological approach holds great promise since it is environment-friendly, cost-effective and energy-efficient. There are several types of microorganisms which inhabit uranium ore bodies and biogenesis plays an important role in the mineralisation and transport of uranium-bearing minerals under the earth's crust. Uranium occurrences in India are only meagre and it becomes essential to tap effectively all the available resources. Uraninite and pitchblende occurring along with sulfide mineralisation such as pyrite are ideal candidates for bioleaching. Acidithiobacillus ferrooxidans present ubiquitously in the ore deposits can be isolated, cultured and utilised to bring about efficient acidic dissolution of uranium. Many such commercial attempts to extract uranium from even lean ores using acidophilic autotrophic bacteria have been made in different parts of the world. Anaerobes such a Geobacter and Sulfate Reducing Bacteria (SRB) can be effectively used in uranium mining for environmental control. Radioactive uranium mined wastes and tailing dumps can be cleaned and protected using microorganisms. In this lecture use of biotechnology in uranium extraction and bioremediation is illustrated with practical examples. Applicability of environment-friendly biotechnology for mining and extraction of uranium from Indian deposits is outlined. Commercial potentials for bioremediation in uranium-containing wastes are emphasised. (author)

Ex-situ bioremediation of Brazilian soil contaminated with plasticizers process wastes

Directory of Open Access Journals (Sweden)

I. D. Ferreira

2012-03-01

Full Text Available The aim of this research was to evaluate the bioremediation of a soil contaminated with wastes from a plasticizers industry, located in São Paulo, Brazil. A 100-kg soil sample containing alcohols, adipates and phthalates was treated in an aerobic slurry-phase reactor using indigenous and acclimated microorganisms from the sludge of a wastewater treatment plant of the plasticizers industry (11gVSS kg-1 dry soil, during 120 days. The soil pH and temperature were not corrected during bioremediation; soil humidity was corrected weekly to maintain 40%. The biodegradation of the pollutants followed first-order kinetics; the removal efficiencies were above 61% and, among the analyzed plasticizers, adipate was removed to below the detection limit. Biological molecular analysis during bioremediation revealed a significant change in the dominant populations initially present in the reactor.

Uranium Biominerals Precipitated by an Environmental Isolate of Serratia under Anaerobic Conditions

Science.gov (United States)

Newsome, Laura; Morris, Katherine; Lloyd, Jonathan. R.

2015-01-01

Stimulating the microbially-mediated precipitation of uranium biominerals may be used to treat groundwater contamination at nuclear sites. The majority of studies to date have focussed on the reductive precipitation of uranium as U(IV) by U(VI)- and Fe(III)-reducing bacteria such as Geobacter and Shewanella species, although other mechanisms of uranium removal from solution can occur, including the precipitation of uranyl phosphates via bacterial phosphatase activity. Here we present the results of uranium biomineralisation experiments using an isolate of Serratia obtained from a sediment sample representative of the Sellafield nuclear site, UK. When supplied with glycerol phosphate, this Serratia strain was able to precipitate 1 mM of soluble U(VI) as uranyl phosphate minerals from the autunite group, under anaerobic and fermentative conditions. Under phosphate-limited anaerobic conditions and with glycerol as the electron donor, non-growing Serratia cells could precipitate 0.5 mM of uranium supplied as soluble U(VI), via reduction to nano-crystalline U(IV) uraninite. Some evidence for the reduction of solid phase uranyl(VI) phosphate was also observed. This study highlights the potential for Serratia and related species to play a role in the bioremediation of uranium contamination, via a range of different metabolic pathways, dependent on culturing or in situ conditions. PMID:26132209

Polyphosphate Amendments for In-Situ Immobilization of Uranium Plumes

International Nuclear Information System (INIS)

Wellman, Dawn M.; Icenhower, Jonathan P.; Pierce, Eric M.; McNamara, Bruce K.; Burton, Sarah D.; Geiszler, Keith N.; Baum, Steven R.; Butler, Bart C.; R.F. Olfenbuttel; P.J. White

2005-01-01

A multi-faceted approach has been taken to address basic science questions with regards to the efficacy of utilizing phosphate amendments for subsurface immobilization of uranium plumes. Hydraulically saturated and unsaturated column tests demonstrate the ability of polyphosphate compounds to control the precipitation kinetics of insoluble phosphate minerals and optimize conditions for controlled application of phosphate amendments for subsurface remediation. X-Ray micro-focus tomography results illustrate long-term effects of phosphate mineralization on hydraulic conductivity. 31P NMR has been utilized to quantify the effect of sedimentary and aqueous components on the in-situ hydrolysis kinetics of condensed polyphosphates. Single-pass flow-through (SPFT) tests have been conducted to evaluate the longevity and quantify the effects of aqueous organic material on the dissolution kinetics of autunite minerals, X1-2[(UO2)(PO4)]2nH2O. Preliminary results indicate: (1) autunite minerals will precipitate within 1-2 months given a 0.05 M phosphate concentration and 10-6 M aqueous uranium concentration, under hydraulically saturated conditions; (2) polyphosphate chain lengths can be optimized for specific site conditions, given thorough knowledge of the subsurface environment; (3) the release of uranium from autunite minerals appears to be 6-7 order of magnitude slower than uranium (UO2) minerals formed by iron barrier reduction; and (4) understanding secondary uranyl-phase formation is necessary for predicting the long-term fate of uranium in the environment

Bioremediation of copper-contaminated soils by bacteria.

Science.gov (United States)

Cornu, Jean-Yves; Huguenot, David; Jézéquel, Karine; Lollier, Marc; Lebeau, Thierry

2017-02-01

Although copper (Cu) is an essential micronutrient for all living organisms, it can be toxic at low concentrations. Its beneficial effects are therefore only observed for a narrow range of concentrations. Anthropogenic activities such as fungicide spraying and mining have resulted in the Cu contamination of environmental compartments (soil, water and sediment) at levels sometimes exceeding the toxicity threshold. This review focuses on the bioremediation of copper-contaminated soils. The mechanisms by which microorganisms, and in particular bacteria, can mobilize or immobilize Cu in soils are described and the corresponding bioremediation strategies-of varying levels of maturity-are addressed: (i) bioleaching as a process for the ex situ recovery of Cu from Cu-bearing solids, (ii) bioimmobilization to limit the in situ leaching of Cu into groundwater and (iii) bioaugmentation-assisted phytoextraction as an innovative process for in situ enhancement of Cu removal from soil. For each application, the specific conditions required to achieve the desired effect and the practical methods for control of the microbial processes were specified.

The Honeymoon project: Australia's first in situ leach uranium project

International Nuclear Information System (INIS)

Ackland, M.C.

1997-01-01

The Honeymoon uranium deposit is one of several roll front uranium deposits in South Australia. It was discovered in 1971, the project developed in the 1970's, and was ready for demonstration of the In Situ Leaching (ISL) production techniques by January 1983, when the project was stopped, despite it having met the environmental approvals to proceed, due to the Australian Labour Party's 'three mines policy'. From 1983 until March 1996 the project was mothballed. In late 1996 Southern Cross Resources Inc. (SCRI) reached agreement with Mount Isa Mining (MIM) to purchase its uranium interests in Honeymoon, Goulds Dam and EL 2310 whilst simultaneously acquiring Sedimentary Holdings NL's interests in EL 2310. By April 1997 these interests were consolidated in SCRI's wholly owned subsidiary, Southern Cross Resources Australia Ply Ltd which is the operating company. Activities are presently underway to rehabilitate the existing treatment plant and continue the program that was outlined in the approved 1981 Honeymoon Environmental Impact Statement

Effects of Triton X-100 and Quillaya Saponin on the ex situ bioremediation of a chronically polychlorobiphenyl-contaminated soil

Energy Technology Data Exchange (ETDEWEB)

Fava, F.; Di Gioia, D. [Bologna Univ. (Italy). Dept. of Applied Chemistry and Material Science

1998-12-31

The possibility of enhancing the ex situ bioremediation of a chronically polychlorinated biphenyl (PCB)-contaminated soil by using Triton X-100 or Quillaya Saponin, a synthetic and a biogenic surfactant, respectively, was studied. The soil, which contained about 350 mg/kg of PCBs and indigenous aerobic bacteria capable of growing on biphenyl or on monochlorobenzoic acids, was amended with inorganic nutrients and biphenyl, saturated with water and treated in aerobic batch slurry- and fixed-phase reactors. Triton X-100 and Quillays Saponin were added to the reactors at a final concentration of 10 g/l at the 42nd day of treatment, and at the 43rd and 100th day, respectively. Triton X-100 was not metabolised by the soil microflora and it exerted inhibitory effects on the indigenous bacteria. Quillaya Saponin, on the contrary, was readily metabolised by the soil microflora. Under slurry-phase conditions, Triton X-100 negatively influenced the soil bioremediation process by affecting the availability of the chlorobenzoic acid degrading indigenous bacteria, wheres Quillays Saponin slightly enhanced the biological degradation and dechlorination of the soil PCBs. In the fixed-phase reactors, where both the surfactant availability and the mixing of the soil were lower, Triton X-100 did not exert inhibitory effects on the soil biomass and enhanced significantly the soil PCB depletion, whereas Quillays Saponin did not influence the bioremediation process. (orig.)

A economic evaluation system software on in-situ leaching mining sandstone uranium deposits

International Nuclear Information System (INIS)

Yao Yixuan; Su Xuebin; Xie Weixing; Que Weimin

2001-01-01

The author presents the study results of applying computer technology to evaluate quantitatively the technical-economic feasibility of in-situ leaching mining sandstone uranium deposits. A computer system software have been developed. Under specifying deposit conditions and given production size per year, the application of the software will generate total capital and mine life operating costs as well as solve for the movable and static financial assessment targets through discounted cash flow analysis. According to the characters of two kinds of sandstone uranium deposits, a data bases of economic and technique parameters of in-situ leaching have been designed. Also the system software can be used to study the economic value of deposits and to optimize the key project parameters. Its features, data input method and demand, main functions, structure and operating environments are described

Application of radioisotope induced EDXRF in bioremediation studies

International Nuclear Information System (INIS)

Joseph, D.; Choudhury, R.K.; Acharya, C.; Narasimha, A.; Apte, S.K.

2010-01-01

Bioremediation is an emerging technology that employs the use of certain microbes for the clean up of heavy metals/radionuclides contaminated environments. Progress in this field is however handicapped by limited knowledge of the biological processes involved in microbial metal uptake, translocation, tolerance and microbe-metal interactions. Therefore a better understanding of the basic biological processes involved in cell/soil/contaminant interactions would allow further optimization of bioremediation technologies. Advanced analytical techniques have proven to be instrumental in understanding the metal microbe interactions. It is important that in bioremediation studies, the analytical procedures used for elemental determination in cells should be fast, cheap, non-destructive, with easy, sample preparation, good sensitivity and accuracy. The present paper demonstrates the utility of Energy Dispersive X-ray Fluorescence Spectroscopy in detection of uranium and tellurium associated with the microbial cells. This technique was found to be convenient and suitable for such metal microbial interactive studies

Environmental bioremediation technologies

Energy Technology Data Exchange (ETDEWEB)

Singh, S.N.; Tripathi, R.D. (eds.) [National Botanical Research Institute, Lucknow (India). Ecotoxicology and Bioremediation

2007-07-01

The rapid expansion and increasing sophistication of various industries in the past century has remarkably increased the amount and complexity of toxic waste effluents, which may be bioremediated by suitable plants and microbes, either natural occurring or tailor-made for the specific purpose. This technology is termed as bioremediation. Bioremediation is an eco- friendly, cost-effective and natural technology targeted to remove heavy metals, radionuclides, xenobiotic compounds, organic waste, pesticides etc. from contaminated sites or industrial discharges through biological means. Since this technology is used in in-situ conditions, it does not physically disturb the site unlike conventional methods i.e. chemical or mechanical methods. In this technology, higher plants or microbes are used alone or in combination for phytoextraction of heavy metals from metal contaminated sites. Through microbial interventions, either the metals are immobilized or mobilized through redox conversions at contaminated sites. If mobilized, metal accumulating plants are put in place to accumulate metals in their body. Thereafter, metal-loaded plants are harvested and incinerated to reduce the volume of waste and then disposed off as hazardous materials or used for recovery of precious metals, if possible. In case of immobilization, metals are no longer available to be toxic to organisms. (orig.)

Non-radioactive disposal facility-bioremediation horizontal well installation project

International Nuclear Information System (INIS)

Kupar, J.; Hasek, M.

1998-01-01

The Sanitary Landfill Corrective Action Plan proposes a two pronged approach to remediation. The first part of the total remediation strategy is the placement of a RCRA style closure cap to provide source control of contaminants into the groundwater. The second part of the proposed remediation package is a phased approach primarily using an in situ bioremediation system for groundwater clean up of the Constituents of Concern (COCs) that exceed their proposed Alternate Concentration Limits (ACL). The phased in approach of groundwater clean up will involve operation of the in situ bioremediation system, followed by evaluation of the Phase 1 system and, if necessary, additional phased remediation strategies. This document presents pertinent information on operations, well locations, anticipated capture zones, monitoring strategies, observation wells and other information which will allow a decision on the acceptability of the remedial strategy as an interim corrective action prior to permit application approval. The proposed interim phase of the remediation program will position two horizontal bioremediation wells such that the respective zones of influence will intersect the migration path for the highest concentrations of each plume

Relationship between characteristics of fan-delta sandstone bodies and in-situ leachable sandstone-type uranium mineralization

International Nuclear Information System (INIS)

Nie Fengjun; Zhou Weixun; Guan Taiyang; Li Sitian

2000-01-01

Like normal deltas, fan-deltas are composed of three parts, i.e., fan-delta plain, fan-delta front and pre-fin-delta, In-situ leachable uranium deposits are commonly distributed along the margins of in-land basins. The author analyzes the possible relationship between the basic characteristics of fan-delta sandstone bodies and uranium mineralization. Two examples, e.g., the fan delta depositional systems in the eastern part of Jungger basin and the southern part of Yili basin, are given to illustrate the fan-delta vertical sequence and planar distribution of sedimentary facies. It has been pointed out that the braided channel sandstone bodies on delta plain, sub-aqueous distributional channel sandstone bodies and delta front sandstone bodies may be the favourable host rocks for in-situ leachable sandstone uranium deposits

Application of microbial biomass and activity measures to assess in situ bioremediation of chlorinated solvents

International Nuclear Information System (INIS)

Phelps, T.J.; Herbes, S.E.; Palumbo, A.V.; Pfiffner, S.M.; Mackowski, R.; Ringelberg, D.; White, D.C.; Tennessee Univ., Knoxville, TN

1993-01-01

Evaluating the effectiveness of chlorinated solvent remediation in the subsurface can be a significant problem given uncertainties in estimating the total mass of contaminants present. If the remediation technique is a biological activity, information on the progress and success of the remediation may be gained by monitoring changes in the mass and activities of microbial populations. The in situ bioremediation demonstration at the US Department of Energy (DOE) Savannah River Site (SRS) is designed to test the effectiveness of methane injection for the stimulation of in sediments. Past studies have shown the potential for degradation by native microbial populations. The design and implementation of the SRS Integrated Demonstration is described in this volume. A control phase without treatment was followed by a phase withdrawing air. The next phase included vacuum extraction plus air injection into the lower horizontal well located below the water table. The next period included the injection of 1% methane in air followed by injection of 4% methane in air. Based on the literature, it was hypothesized that the injection of methane would stimulate methanotrophic populations and thus accelerate biological degradation of TCE. Measuring the success of bioremediation is a complex effort that includes monitoring of changes in microbial populations associated with TCE degradation. These monitoring efforts are described in this paper and in related papers in this volume

Problem-oriented software for the managing of uranium mining by in-situ leaching

International Nuclear Information System (INIS)

Noskov, M.D.; Gutsul, M.V.; Istomin, A.D.; Kesler, A.G.; Noskova, S.N.; Cheglokov, A.A.

2013-01-01

The problem-oriented software consisting of interconnected geological geoinformation, technological information, geotechnological modeling and expert-analytical systems is presented. The software application procedure for the managing of uranium field development by in-situ leaching is considered [ru

Bioremediation of soils and sediments containing PAHs and PCP using Daramend trademark

International Nuclear Information System (INIS)

Seech, A.; Burwell, S.; Marvan, I.

1994-01-01

A full-scale demonstration of Grace Dearborn's Daramend trademark for bioremediation of soil containing chlorinated phenols, PAHs and petroleum hydrocarbons is being conducted at an industrial wood treatment site in Ontario. A pilot-scale demonstration of Daramend for the clean-up of sediments contaminated with PAHs was also conducted. The full-scale demonstration, which includes bioremediation of approximately 4,500 m 3 of soil, was initiated at a wood preserving facility in Ontario, in the summer of 1993. The soil contains chlorinated phenols, PAHs and total petroleum hydrocarbons at concentrations of up to 700, 1,400 and 6,300 mg/kg respectively. Full-scale bioremediation at this site employs the same Daramend protocols and organic amendment treatments that were used at the pilot-scale phase where the PAH, total petroleum hydrocarbon, and pentachlorophenol concentrations were reduced to below the Canadian clean-up guidelines for industrial soils. In addition, the toxicity of the soil to earthworms was eliminated while the rate of seed germination was increased to that of an agricultural soil during the pilot scale demonstration phase. The ex-situ portion of the full-scale demonstration is currently being audited by the EPA under the SITE program. This paper will focus on the ex-situ work. The pilot-scale demonstration of sediment remediation consisted of ex-situ bioremediation of approximately 90 tonnes of PAH-contaminated sediment in a confined treatment area

Evaluation of in-situ methanotrophic bioremediation for contaminated groundwater, St. Joseph, Michigan. Final report, January 1989-December 1989

International Nuclear Information System (INIS)

McCarty, P.L.; Semprini, L.; Dolan, M.E.; Harmon, T.C.; Just, S.

1990-09-01

A feasibility study of utilizing indigenous bacteria that use methane as a source of cell carbon and energy (methanotrophs) for in-situ bioremediation of groundwater contaminants at the St. Joseph site is summarized. The contaminants, compounds, can be biotransformed by methanotrophic bacteria, which are found in some locations of the site in adequate populations. The process involves stimulating the growth of native populations of methanotrophs by injecting water containing dissolved methane and oxygen into the aquifer. The stimulated population of methanotrophs in turn has the capability to degrade trichloroethylene, 1,2-cis-dichloroethylene, 1,2-trans-dichloroethylene, and vinyl chloride

Washing technology development for gravel contaminated with uranium

Energy Technology Data Exchange (ETDEWEB)

Park, Uk Ryang; Kim, Gye Nam; Kim, Seung Soo; Kim, Wan Suk; Moon, Jai Kwon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2013-10-15

The soil washing method has a short decontamination time and is economical. In addition, methods including phytoremediation, solidification/stabilization and bioremediation exist. Phytoremediation and bioremediation are economical, but have low remedial efficiency. In addition, bioremediation causes washing wastewater because it requires a washing process for the separation of microorganisms from the soils. In addition, solidification/stabilization is a commonly used methods, but eventually increases the volume of wastes. As mentioned above, many researches involved in the decontamination of radioactively contaminated soils have been actively processed. On the other hand, researches for decontaminating radioactively contaminated gravels are not being currently processed. In this study, we performed basic experiments using decontamination methods to decontaminate radioactively contaminated gravel. First, we measured the concentration of uranium in gravel included in uranium-contaminated soils and performed a washing experiment to monitor the tendency of uranium removal. In addition, when managing gravel with a low uranium-decontamination rate, we tried to satisfy the radioactivity concentration criteria for self-disposal in the wastes (0.4Bq/g or less) by performing a washing experiment after only a physical crushing process. We performed washing experiments to satisfy the radioactivity concentration criteria for self-disposal (0.4 Bq/g or less) in gravel included in radioactively contaminated soil. We performed washing experiments for gravel whose initial average concentration of uranium was 1.3Bq/g. In addition, the average concentration of uranium was 0.8Bq/g. Too increase the decontamination rate, we crushed the gravel with a jaw crusher and performed the washing experiments. The results were similar to the results without crushing. In addition, it was determined that the smaller the size of the gravel particles, the more efficient the uranium decontamination

Waste water treatment of CO2+O2 in-situ leaching uranium

International Nuclear Information System (INIS)

Xu Lechang; Liu Naizhong; Du Zhiming; Wang Hongying

2012-01-01

An in-situ leaching uranium mine located in Northern China uses CO 2 +O 2 leaching process to leach uranium. The consumption of industrial reagent and water, and generation and discharge of waste water are minimized by comprehensive waste water treatment technology with process water recycle, reverse osmosis and natural evaporation. The process water of the mine that can be recycled and reused includes barren fluid, solution washing loaded resin, precipitating mother solution and filtered liquor of yellow cake. Solution regenerating barren resin is treated by reverse osmosis. Concentrated water from reverse osmosis and solution washing barren resin are naturally evaporated. (authors)

In-situ leaching of Crownpoint, New Mexico, uranium ore: Part 7 - laboratory study of chemical agents for molybdenum restoration

International Nuclear Information System (INIS)

Strom, E.T.; Vogt, T.C.

1985-01-01

While in-situ leaching has significant advantages over conventional uranium recovery methods, one possible drawback to its use is the potential release of previously insoluble chemical species into the formation water. Before Mobil began a pilot test of in-situ uranium leaching at Crownpoint, New Mexico, extensive laboratory studies were undertaken to develop chemical methods for treating one possible contaminant, molybdenum (Mo). In-situ production of uranium entails oxidizing uranium from the insoluble +4 oxidation state to the soluble, readily complexed +6 state. However, this process also transforms insoluble Mo +4 compounds such as molybdenite or jordesite, MoS 2 , into the soluble T6 form, molybdate, Mo0 4 2- . New Mexico regulations restrict the amount of Mo permissible in formation waters after leaching to less than one ppm. Conceptually, Mo restoration after leaching can be dealt with in one of two ways. (1) The oxidizing environment can be left unchanged with something added to render the molybdate ion insoluble or (2) the environment can be changed to a reducing one, converting the Mo back to the less soluble +4 oxidation state

Field Testing of Downgradient Uranium Mobility at an In-Situ Recovery Uranium Mine

Science.gov (United States)

Reimus, P. W.; Clay, J. T.; Rearick, M.; Perkins, G.; Brown, S. T.; Basu, A.; Chamberlain, K.

2015-12-01

In-situ recovery (ISR) mining of uranium involves the injection of O2 and CO2 (or NaHCO3) into saturated roll-front deposits to oxidize and solubilize the uranium, which is then removed by ion exchange at the surface and processed into U3O8. While ISR is economical and environmentally-friendly relative to conventional mining, one of the challenges of extracting uranium by this process is that it leaves behind a geochemically-altered aquifer that is exceedingly difficult to restore to pre-mining geochemical conditions, a regulatory objective. In this research, we evaluated the ability of the aquifer downgradient of an ISR mining area to attenuate the transport of uranium and other problem constituents that are mobilized by the mining process. Such an evaluation can help inform both regulators and the mining industry as to how much restoration of the mined ore zone is necessary to achieve regulatory compliance at various distances downgradient of the mining zone even if complete restoration of the ore zone proves to be difficult or impossible. Three single-well push-pull tests and one cross-well test were conducted in which water from an unrestored, previously-mined ore zone was injected into an unmined ore zone that served as a geochemical proxy for the downgradient aquifer. In all tests, non-reactive tracers were injected with the previously-mined ore zone water to allow the transport of uranium and other constituents to be compared to that of the nonreactive species. In the single-well tests, it was shown that the recovery of uranium relative to the nonreactive tracers ranged from 12-25%, suggesting significant attenuation capacity of the aquifer. In the cross-well test, selenate, molybdate and metavanadate were injected with the unrestored water to provide information on the transport of these potentially-problematic anionic constituents. In addition to the species-specific transport information, this test provided valuable constraints on redox conditions within

Radiometric determination in situ of the face grades in Witwatersrand gold and uranium mines

International Nuclear Information System (INIS)

Smit, C.J.B.

1985-01-01

A prototype collimated radiometric face scanner was tested in the Harmony Gold Mine. The results obtained during the pilot study indicate that in situ radiometric uranium assays are statistically indistinguishable from those obtained conventionally from channel chip samples. In addition, the study demonstrated that reasonably reliable gold estimates can be deduced from the radiometric measurements, by use of the ratio of gold to uranium within a mine. The instrumentation, calibration procedures, and background determination are described briefly

Biostimulation of Iron Reduction and Uranium Immobilization: Microbial and Mineralogical Controls

International Nuclear Information System (INIS)

Joel E. Kostka; Lainie Petrie; Nadia North; David L. Balkwill; Joseph W. Stucki; Lee Kerkhof

2004-01-01

The overall objective of our project is to understand the microbial and geochemical mechanisms controlling the reduction and immobilization of U(VI) during biostimulation in subsurface sediments of the Field Research Center (FRC) which are cocontaminated with uranium and nitrate. The focus will be on activity of microbial populations (metal- and nitrate-reducing bacteria) and iron minerals which are likely to make strong contributions to the fate of uranium during in situ bioremediation. The project will: (1) quantify the relationships between active members of the microbial communities, iron mineralogy, and nitrogen transformations in the field and in laboratory incubations under a variety of biostimulation conditions, (2) purify and physiologically characterize new model metal-reducing bacteria isolated from moderately acidophilic FRC subsurface sediments, and (3) elucidate the biotic and abiotic mechanisms by which FRC aluminosilicate clay minerals are reduced and dissolved under environmental conditions resembling those during biostimulation. Active microbial communities will be assessed using quantitative molecular techniques along with geochemical measurements to determine the different terminal-electron-accepting pathways. Iron minerals will be characterized using a suite of physical, spectroscopic, and wet chemical methods. Monitoring the activity and composition of the denitrifier community in parallel with denitrification intermediates during nitrate removal will provide a better understanding of the indirect effects of nitrate reduction on uranium speciation. Through quantification of the activity of specific microbial populations and an in-depth characterization of Fe minerals likely to catalyze U sorption/precipitation, we will provide important inputs for reaction-based biogeochemical models which will provide the basis for development of in situ U bioremediation strategies. In collaboration with Jack Istok and Lee Krumholz, we have begun to study the

Heavy Metal Polluted Soils: Effect on Plants and Bioremediation Methods

Directory of Open Access Journals (Sweden)

G. U. Chibuike

2014-01-01

Full Text Available Soils polluted with heavy metals have become common across the globe due to increase in geologic and anthropogenic activities. Plants growing on these soils show a reduction in growth, performance, and yield. Bioremediation is an effective method of treating heavy metal polluted soils. It is a widely accepted method that is mostly carried out in situ; hence it is suitable for the establishment/reestablishment of crops on treated soils. Microorganisms and plants employ different mechanisms for the bioremediation of polluted soils. Using plants for the treatment of polluted soils is a more common approach in the bioremediation of heavy metal polluted soils. Combining both microorganisms and plants is an approach to bioremediation that ensures a more efficient clean-up of heavy metal polluted soils. However, success of this approach largely depends on the species of organisms involved in the process.

The Honeymoon project: Australia`s first in situ leach uranium project

Energy Technology Data Exchange (ETDEWEB)

Ackland, M.C. [Southern Cross Resources Inc. Toowond, QLD (Australia)

1997-12-31

The Honeymoon uranium deposit is one of several roll front uranium deposits in South Australia. It was discovered in 1971, the project developed in the 1970`s, and was ready for demonstration of the In Situ Leaching (ISL) production techniques by January 1983, when the project was stopped, despite it having met the environmental approvals to proceed, due to the Australian Labour Party`s `three mines policy`. From 1983 until March 1996 the project was mothballed. In late 1996 Southern Cross Resources Inc. (SCRI) reached agreement with Mount Isa Mining (MIM) to purchase its uranium interests in Honeymoon, Goulds Dam and EL 2310 whilst simultaneously acquiring Sedimentary Holdings NL`s interests in EL 2310. By April 1997 these interests were consolidated in SCRI`s wholly owned subsidiary, Southern Cross Resources Australia Ply Ltd which is the operating company. Activities are presently underway to rehabilitate the existing treatment plant and continue the program that was outlined in the approved 1981 Honeymoon Environmental Impact Statement. 2 tabs., 3 figs.

In situ carbonate leaching and recovery of uranium from ore deposits

International Nuclear Information System (INIS)

Hunkin, G.G.; Fife, T.P.; Stano, J.R.

1979-01-01

Uranium is leached from redox roll ore deposits by selective in-situ leaching with a solution of pH 7.4 to 9 (preferably 7.5 to 8.5) containing from about 0.5 to 5g/l of NH 4 HCO 3 and from about 0.1 to 3g/l of peroxide (preferably aqueous H 2 O 2 ), and sufficient NH 3 to maintain the desired pH. The leach solution is then withdrawn from the ore deposit and contacted with a strong base anion exchange material to strip the uranium from the leach solution. The uranium is eluted from the anion exchange material by an aqueous eluant, and the uranium is recovered from the eluate by first acidifying it and then treating it with ammonia to produce a precipitate of relatively pure ammonium diuranate. The content of the three components in the stripped leach solution is adjusted, and then the leach solution is recirculated through the ore deposit. After the uranium ore is removed to the extent economically practicable, the leach solution is replaced with an aqueous reducing solution which when passed into the ore deposit precipitates and renders insoluble any uranium and elements such as vanadium, molybdenum, and selenium. This process produces above ground a very low volume of impurities and waste solutions requiring disposal and does not cause material contamination of the underground deposit or any aquifer associated with the deposit

Shifts in microbial community structure during in situ surfactant-enhanced bioremediation of polycyclic aromatic hydrocarbon-contaminated soil.

Science.gov (United States)

Wang, Lingwen; Li, Feng; Zhan, Yu; Zhu, Lizhong

2016-07-01

This study aims to reveal the microbial mechanism of in situ surfactant-enhanced bioremediation (SEBR). Various concentrations of rhamnolipids, Tween 80, and sodium dodecyl benzenesulfonate (SDBS) were separately sprayed onto soils contaminated with polycyclic aromatic hydrocarbons (PAHs) for years. Within 90 days, the highest level of degradation (95 %) was observed in the soil treated with rhamnolipids (10 mg/kg), followed by 92 % degradation with Tween 80 (50 mg/kg) and 90 % degradation with SDBS (50 mg/kg). The results of the microbial phospholipid fatty acids (PLFAs) suggest that bacteria dominated the enhanced PAH biodegradation (94 % of the maximum contribution). The shift of bacterial community structure during the surfactant treatment was analyzed by using the 16S rRNA gene high-throughput sequencing. In the presence of surfactants, the number of the operational taxonomic units (OTUs) associated with Bacillus, Pseudomonas, and Sphingomonas increased from 2-3 to 15-30 % at the end of the experiment (two to three times of control). Gene prediction with phylogenetic investigation of communities by reconstruction of unobserved states (PICRUSt) shows that the PAH-degrading genes, such as 1-hydroxy-2-naphthoate dioxygenase and PAH dioxygenase large subunit, significantly increased after the surfactant applications (p bioremediation.

Molecular analyis of rates of metal reductions and metabolic state of Geobacter species

International Nuclear Information System (INIS)

Lovley, Derek R.

2008-01-01

This project began with the simple goal of trying to understand the diversity of dissimilatory metal-reducing microorganisms that might be found in subsurface environments. It ended with a sophisticated understanding not only of what microorganisms are important for metal reduction in uranium-contaminated subsurface environments, but also their physiological status during in situ uranium bioremediation. These findings have provided unprecedented insight into uranium bioremediation and the methods by which this process might be optimized. A brief summary of the major accomplishments of the project is given.

From Nanowires to Biofilms: An Exploration of Novel Mechanisms of Uranium Transformation Mediated by Geobacter Bacteria

Energy Technology Data Exchange (ETDEWEB)

REGUERA, GEMMA [Michigan State University

2014-01-16

One promising strategy for the in situ bioremediation of radioactive groundwater contaminants that has been identified by the SBR Program is to stimulate the activity of dissimilatory metal-reducing microorganisms to reductively precipitate uranium and other soluble toxic metals. The reduction of U(VI) and other soluble contaminants by Geobacteraceae is directly dependent on the reduction of Fe(III) oxides, their natural electron acceptor, a process that requires the expression of Geobacter’s conductive pili (pilus nanowires). Expression of conductive pili by Geobacter cells leads to biofilm development on surfaces and to the formation of suspended biogranules, which may be physiological closer to biofilms than to planktonic cells. Biofilm development is often assumed in the subsurface, particularly at the matrix-well screen interface, but evidence of biofilms in the bulk aquifer matrix is scarce. Our preliminary results suggest, however, that biofilms develop in the subsurface and contribute to uranium transformations via sorption and reductive mechanisms. In this project we elucidated the mechanism(s) for uranium immobilization mediated by Geobacter biofilms and identified molecular markers to investigate if biofilm development is happening in the contaminated subsurface. The results provided novel insights needed in order to understand the metabolic potential and physiology of microorganisms with a known role in contaminant transformation in situ, thus having a significant positive impact in the SBR Program and providing novel concept to monitor, model, and predict biological behavior during in situ treatments.

Bioremediation: is it the solution to reclamation of heavy oil contaminated soils in the Canadian climate?

International Nuclear Information System (INIS)

Goodman, R.; Nicholson, P.; Varga, M.; Boadi, D.; Yang, A.

1997-01-01

The issue of bioremediation of heavy oil contaminated soils in cold climates was discussed. No model of the bioremediation system for cold climates exists. Environmental groups use three environmental concepts as the basis to evaluate petroleum activities: (1) cradle to grave responsibility, (2) the precautionary principle, and (3) sustainable development. The reclamation of an abandoned petroleum production facility must meet stringent standards. Most sites are contaminated with weathered hydrocarbons, brine and other chemicals that have been used at the location. Bioremediation, either in-situ or ex-situ, is one of the lowest cost remediation techniques available and has been used extensively by the downstream petroleum industry in warm climates. However, there are many unresolved issues with the use of bioremediation in cold climates, for heavy or weathered crude oil products and in areas of clay or other low permeability. Some of these unresolved issues are highlighted

Engineering Deinococcus geothermailis for Bioremediation of High-Temperature Radioactive Waste Environments

International Nuclear Information System (INIS)

Brim, Hassan; Venkateswaran, Amudhan; Kostandarithes, Heather M.; Fredrickson, Jim K.; Daly, Michael J.

2003-01-01

Deinococcus geothermalis is an extremely radiation-resistant thermophilic bacterium closely related to the mesophile Deinococcus radiodurans, which is being engineered for in situ bioremediation of radioactive wastes

Laboratory study on leaching of a sandstone-type uranium deposit for acid in-situ leaching

International Nuclear Information System (INIS)

Wen Zhenqian; Yao Yixuan; Zheng Jianping; Jiang Yan; Cui Xin; Xing Yongguo; Hao Jinting; Tang Huazhang

2013-01-01

Ore samples were took from in-situ leaching experiment boreholes in a sandstone-type uranium deposit. Technological mineralogy study, agitating leaching and column leaching experiments were carried. The results show that the content of minerals consuming acid and deoxidized minerals is low. When sulfuric acid concentration was 1O g/L, initial uranium content was 0.0224%, and liquid-to-solid ratio was l.91, leaching rate of column leaching experiments is 89.19%, acid consumption is 8.2 kg/t ore, acid consumption is 41.88 t/tU. Acid leaching, technology is recommend for field in-situ leaching experiment, sulfuric acid concentration in confecting solution is 10 g/L, and oxidizing agent is needless during leaching process. (authors)

Uranium resource technology, Seminar 3, 1980

International Nuclear Information System (INIS)

Morse, J.G.

1980-01-01

This conference proceedings contains 20 papers and 1 panel discussion on uranium mining and ore treatment, taking into account the environmental issues surrounding uranium supply. Topics discussed include: the US uranium resource base, the technology and economics of uranium recovery from phosphate resources, trends in preleash materials handling of sandstone uranium ores, groundwater restoration after in-situ uranium leaching, mitigation of the environmental impacts of open pit and underground uranium mining, remedial actions at inactive uranium mill tailings sites, environmental laws governing in-situ solution mining of uranium, and the economics of in-situ solution mining. 16 papers are indexed separately

Execution of pilot tests for an uranium in situ leaching project

International Nuclear Information System (INIS)

Koch, H.J.

1983-01-01

Urangesellschaft is presently evaluating the technical and economic feasibility of an in situ leaching (ISL) project in Wyoming/USA. This report describes the basic technical principles for ISL-uranium projects and gives the reasons for conducting pilot tests prior to the construction of a commercial plant. It further describes the licensing requirements for an ISL-pilot plant and evaluates the results of the pilot tests. (orig.) [de

Modeling the migration of radioactive contaminants in groundwater of in situ leaching uranium mine

International Nuclear Information System (INIS)

Li Chunguang; Tai Kaixuan

2011-01-01

The radioactive contamination of groundwater from in situ leaching (ISL) of uranium mining is a widespread environmental problem. This paper analyzed the monitor results of groundwater contaminations for a in situ leaching uranium mine. A dynamic model of contaminants transport in groundwater in ISL well field was established. The processes and mechanisms of contaminant transport in groundwater were simulated numerically for a ISL well field. A small quantity of U and SO 4 2- migrate to outside of well field during ISL production stage. But the migration velocity and distance of contaminations is small, and the concentration is low. Contaminants migrate as anomalistic tooth-shape. The migration trend of U and SO 4 2- is consistent. Numerical modeling can provide an effective approach to analyse the transport mechanism, and forecast and control the migration of contaminants in groundwater in ISL well field. (authors)

A multi-objective simulation-optimization model for in situ bioremediation of groundwater contamination: Application of bargaining theory

Science.gov (United States)

Raei, Ehsan; Nikoo, Mohammad Reza; Pourshahabi, Shokoufeh

2017-08-01

In the present study, a BIOPLUME III simulation model is coupled with a non-dominating sorting genetic algorithm (NSGA-II)-based model for optimal design of in situ groundwater bioremediation system, considering preferences of stakeholders. Ministry of Energy (MOE), Department of Environment (DOE), and National Disaster Management Organization (NDMO) are three stakeholders in the groundwater bioremediation problem in Iran. Based on the preferences of these stakeholders, the multi-objective optimization model tries to minimize: (1) cost; (2) sum of contaminant concentrations that violate standard; (3) contaminant plume fragmentation. The NSGA-II multi-objective optimization method gives Pareto-optimal solutions. A compromised solution is determined using fallback bargaining with impasse to achieve a consensus among the stakeholders. In this study, two different approaches are investigated and compared based on two different domains for locations of injection and extraction wells. At the first approach, a limited number of predefined locations is considered according to previous similar studies. At the second approach, all possible points in study area are investigated to find optimal locations, arrangement, and flow rate of injection and extraction wells. Involvement of the stakeholders, investigating all possible points instead of a limited number of locations for wells, and minimizing the contaminant plume fragmentation during bioremediation are new innovations in this research. Besides, the simulation period is divided into smaller time intervals for more efficient optimization. Image processing toolbox in MATLAB® software is utilized for calculation of the third objective function. In comparison with previous studies, cost is reduced using the proposed methodology. Dispersion of the contaminant plume is reduced in both presented approaches using the third objective function. Considering all possible points in the study area for determining the optimal locations

DOE In Situ Remediation Integrated Program

International Nuclear Information System (INIS)

Yow, J.L. Jr.

1993-01-01

The In Situ Remediation Integrated Program (ISRP) supports and manages a balanced portfolio of applied research and development activities in support of DOE environmental restoration and waste management needs. ISRP technologies are being developed in four areas: containment, chemical and physical treatment, in situ bioremediation, and in situ manipulation (including electrokinetics). the focus of containment is to provide mechanisms to stop contaminant migration through the subsurface. In situ bioremediation and chemical and physical treatment both aim to destroy or eliminate contaminants in groundwater and soils. In situ manipulation (ISM) provides mechanisms to access contaminants or introduce treatment agents into the soil, and includes other technologies necessary to support the implementation of ISR methods. Descriptions of each major program area are provided to set the technical context of the ISM subprogram. Typical ISM needs for major areas of in situ remediation research and development are identified

Recent developments in uranium resources and production with emphasis on in situ leach mining. Proceedings of a technical meeting

International Nuclear Information System (INIS)

2004-06-01

An important role of the International Atomic Energy Agency is establishing contacts between Member States in order to foster the exchange of scientific and technical information on uranium production technologies. In situ leach (ISL) mining is defined as, the extraction of uranium from the host sandstone by chemical solutions and the recovery of uranium at the surface. ISL extraction is conducted by injecting a suitable leach solution into the ore zone below the water table; oxidizing, complexing, and mobilizing the uranium; recovering the pregnant solutions through production wells; and, finally, pumping the uranium bearing solution to the surface for further processing. As compared with conventional mining, in situ leach is recognized as having economic and environmental advantages when properly employed by knowledgeable specialists to extract uranium from suitable sandstone type deposits. Despite its limited applicability to specific types of uranium deposits, in recent years ISL uranium mining has been producing 15 to 21 per cent of world output. In 2002, ISL production was achieved in Australia, China, Kazakhstan, the United States of America and Uzbekistan. Its importance is expected to increase with new projects in Australia, China, Kazakhstan and the Russian Federation. The Technical Meeting on Recent Development in Uranium Resources and Production with Special Emphasis on In Situ Leach Mining, was held in Beijing from 18 to 20 September 2002, followed by the visit of the Yili ISL mine, Xinjiang Autonomous Region, China, from 21 to 23 September 2002. The meeting, held in cooperation with the Bureau of Geology, China National Nuclear Cooperation, was successful in bringing together 59 specialists representing 18 member states and one international organization (OECD/Nuclear Energy Agency). The papers describe a wide variety of activities related to the theme of the meeting. Subjects such as geology, resources evaluation, licensing, and mine restoration were

Monitoring an in-situ uranium mining site with radio tomography

International Nuclear Information System (INIS)

Stolarczyk, L.; Mondt, W.; Mays, W.

1991-01-01

A field test site has been developed to monitor ground water restoration in an in-situ uranium mining project. Uranium deposited in a shallow buried fluvial sandstone channel (aquifer) has been mined by the injection and recovery of ammonia carbonate leachant from a constellation of drillholes. Ground water restoration is accomplished by injecting clean water into a well and recovering contaminated water from companion wells. The restoration process exchanges clean water for contaminated water in the aquifer. The stratigraphic cross section of the aquifer and the hydro-dynamics of the ground water restoration process is currently being investigated with radio wave tomography. Crosshole continuous wave (CW) radio signals are propagated from a well to a second well in the constellation of drillholes. The magnitude and phase of the radio wave are measured in the second well with Radio Imaging Method (RIM) instruments. The acquired data is processed in tomography algorithms to determine the EM wave propagation constants (attenuation rate [α] and phase constant [β]) in each pixel that covers the image plane between wells. The in-situ electrical conductivity values are computed from the pixel propagation constants. Contaminated ground water causes the conductivity of the local zone of the aquifer to increase. This paper describes the initial radio tomography mapping of the deposit lithology and compares radio tomography and E log conductivity values

In situ leach uranium mining. Proceedings of a technical committee meeting. Working material

International Nuclear Information System (INIS)

2002-03-01

At the beginning of 1996 there were 437 nuclear power plants in operation with a combined electricity generating capacity of 344 GWe (net gigawatts electric). This represents nearly a 100% increase over the last decade. In 1995 over 2228 TWh (terawatt hours) electricity were generated, equivalent to about 17% of the world's total electricity. To achieve this, about 61 400 tonnes U were required as nuclear fuel. The 15 year decline of the spot uranium price, as indicated by Nuexco Exchange Value (NEV) and other indices, which reached an all time low annual average in 1994 of $18.33/kg U ($7.05/pound U 3 O 8 ), has had a profound impact on uranium related activities. This led to the massive reduction and realignment of all uranium related activities as the worldwide uranium market adjusted from over-production. Because of the economic advantages of properly run in situ leach technology on carefully selected uranium orebodies, relatively more ISL mining facilities have been kept in operation than conventional mining operations. In 1995 world uranium production of about 34 000 t uranium met only about 55% of world requirements. An estimated 16% of production came from ISL mining. In 1996 ISL mining was estimated to have produced over 5600 tU, or over 15% of estimated world production of 36 400 tU. The importance of ISL mining is expected to increase, as the technology has economic and environmental advantages for producing uranium from carefully selected deposits when projects are properly designed and operated by experienced personnel. Several countries host sandstone type uranium deposits, the only type where commercial ISL projects have been developed. ISL uranium mining technology was developed independently in the USA and the former Soviet Union and associated non-WOCA (world outside centrally planned economic areas) countries starting in the 1960s and 1970s. Since the opening of relations between the two areas in the early 1990s there has been a high level of

Electrokinetic-enhanced bioremediation of organic contaminants: a review of processes and environmental applications.

Science.gov (United States)

Gill, R T; Harbottle, M J; Smith, J W N; Thornton, S F

2014-07-01

There is current interest in finding sustainable remediation technologies for the removal of contaminants from soil and groundwater. This review focuses on the combination of electrokinetics, the use of an electric potential to move organic and inorganic compounds, or charged particles/organisms in the subsurface independent of hydraulic conductivity; and bioremediation, the destruction of organic contaminants or attenuation of inorganic compounds by the activity of microorganisms in situ or ex situ. The objective of the review is to examine the state of knowledge on electrokinetic bioremediation and critically evaluate factors which affect the up-scaling of laboratory and bench-scale research to field-scale application. It discusses the mechanisms of electrokinetic bioremediation in the subsurface environment at different micro and macroscales, the influence of environmental processes on electrokinetic phenomena and the design options available for application to the field scale. The review also presents results from a modelling exercise to illustrate the effectiveness of electrokinetics on the supply electron acceptors to a plume scale scenario where these are limiting. Current research needs include analysis of electrokinetic bioremediation in more representative environmental settings, such as those in physically heterogeneous systems in order to gain a greater understanding of the controlling mechanisms on both electrokinetics and bioremediation in those scenarios. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

TREATMENT TESTS FOR EX SITU REMOVAL OF CHROMATE & NITRATE & URANIUM (VI) FROM HANFORD (100-HR-3) GROUNDWATER FINAL REPORT

Energy Technology Data Exchange (ETDEWEB)

BECK MA; DUNCAN JB

1994-01-03

This report describes batch and ion exchange column laboratory scale studies investigating ex situ methods to remove chromate (chromium [VI]), nitrate (NO{sub 3}{sup -}) and uranium (present as uranium [VI]) from contaminated Hanford site groundwaters. The technologies investigated include: chemical precipitation or coprecipitation to remove chromate and uranium; and anion exchange to remove chromate, uranium and nitrate. The technologies investigated were specified in the 100-HR-3 Groundwater Treatability Test Plan. The method suggested for future study is anion exchange.

In situ leach method for recovering uranium and related values

International Nuclear Information System (INIS)

Yan, T.Y.

1981-01-01

A process is provided for in-situ leaching of uranium from a calcium-containing clay which does not result in contamination of the clay formation by any cations not already present. A lixiviant is prepared by dissolving carbon dioxide into water having essentially the same cationic composition as that of the formation connate water. The solution is injected along with an oxidant, for example oxygen, into the formation. Calcium that has become dissolved in the lixiviant must be removed to control the pH, preferably by the addition of lime in a calcium precipitator. After calcium removal the lixiviant is filtered to remove suspended solids and is passed through an ion exchange resin or other uranium extraction means. The barren solution goes to a mix tank where carbon dioxide is added, and the fresh lixiviant is injected along with additional oxidant into the formation

Sensibility test for uranium ores from Qianjiadian sandstone type uranium deposit

International Nuclear Information System (INIS)

Zhang Mingyu

2005-01-01

Sensibility tests for uranium ores from Qianjiadian sandstone type uranium deposit in Songliao Basin which is suitable to in-situ leach are carried out, including water sensibility, velocity sensibility, salt sensibility, acid sensibility and alkaline sensibility. The sensibility critical value of this ore is determined. Some references on mining process and technical parameter are provided for in-situ leaching of uranium. (authors)

Challenging oil bioremediation at deep-sea hydrostatic pressure

Directory of Open Access Journals (Sweden)

Alberto Scoma

2016-08-01

Full Text Available The Deepwater Horizon (DWH accident has brought oil contamination of deep-sea environments to worldwide attention. The risk for new deep-sea spills is not expected to decrease in the future, as political pressure mounts to access deep-water fossil reserves, and poorly tested technologies are used to access oil. This also applies to the response to oil-contamination events, with bioremediation the only (biotechnology presently available to combat deep-sea spills. Many questions about the fate of petroleum-hydrocarbons at deep-sea remain unanswered, as much as the main constraints limiting bioremediation under increased hydrostatic pressures and low temperatures. The microbial pathways fueling oil take up are unclear, and the mild upregulation observed for beta-oxidation-related genes in both water and sediments contrasts with the high amount of alkanes present in the spilled-oil. The fate of solid alkanes (tar and that of hydrocarbons degradation rates was largely overlooked, as the reason why the most predominant hydrocarbonoclastic genera were not enriched at deep-sea, despite being present at hydrocarbon seeps at the Gulf of Mexico. This mini-review aims at highlighting the missing information in the field, proposing a holistic approach where in situ and ex situ studies are integrated to reveal the principal mechanisms accounting for deep-sea oil bioremediation.

Uranium biomineralization by a metal resistant Pseudomonas aeruginosa strain isolated from contaminated mine waste

Energy Technology Data Exchange (ETDEWEB)

Choudhary, Sangeeta [Department of Biotechnology, Indian Institute of Technology, Kharagpur 721302 (India); Sar, Pinaki, E-mail: sarpinaki@yahoo.com [Department of Biotechnology, Indian Institute of Technology, Kharagpur 721302 (India)

2011-02-15

Uranium biomineralization by a metal-resistant Pseudomonas aeruginosa strain isolated from uranium mine waste was characterized for its potential in bioremediation. Uranium resistance, its cellular localization and chemical nature of uranium-bacteria interaction were elucidated. Survival and uranium biomineralization from mine water were investigated using microcosm experiments. The selected bacterium showed U resistance and accumulation (maximum of 275 mg U g{sup -1} cell dry wt.) following incubation in 100 mg U L{sup -1}, pH 4.0, for 6 h. Transmission electron microscopy and X-ray diffraction analyses revealed that bioaccumulated uranium was deposited within the cell envelope as needle shaped U-phosphate compounds that attain crystallinity only at pH 4.0. A synergistic involvement of deprotonated phosphate and carboxyl moieties in facilitating bioprecipitation of uranium was evident from FTIR analysis. Based on these findings we attribute the localized U sequestration by this bacterium as innocuous complex to its possible mechanism of uranium resistance. Microcosm data confirmed that the strain can remove soluble uranium (99%) and sequester it as U oxide and phosphate minerals while maintaining its viability. The study showed that indigenous bacteria from contaminated site that can survive uranium and other heavy metal toxicity and sequester soluble uranium as biominerals could play important role in uranium bioremediation.

The use of vinasse as an amendment to ex-situ bioremediation of soil and groundwater contaminated with diesel oil

Directory of Open Access Journals (Sweden)

Adriano Pinto Mariano

2009-08-01

Full Text Available This work investigated the possibility of using vinasse as an amendment in ex-situ bioremediation processes. Groundwater and soil samples were collected at petrol stations. The soil bioremediation was simulated in Bartha biometer flasks, used to measure the microbial CO2 production, during 48 days, where vinasse was added at a concentration of 33 mL.Kg-1of soil. Biodegradation efficiency was also measured by quantifying the total petroleum hydrocarbons (TPH by gas chromatography. The groundwater bioremediation was carried out in laboratory experiments simulating aerated (bioreactors and not aerated (BOD flasks conditions. In both the cases, the concentration of vinasse was 5 % (v/v and different physicochemical parameters were evaluated during 20 days. Although an increase in the soil fertility and microbial population were obtained with the vinasse, it demonstrated not to be adequate to enhance the bioremediation efficiency of diesel oil contaminated soils. The addition of the vinasse in the contaminated groundwaters had negative effects on the biodegradation of the hydrocarbons, since vinasse, as a labile carbon source, was preferentially consumed.Este trabalho investigou a possibilidade de se usar a vinhaça como um agente estimulador de processos de biorremediação ex-situ. Amostras de água subterrânea e solo foram coletadas em três postos de combustíveis. A biorremediação do solo foi simulada em frascos de Bartha, usados para medir a produção de CO2, durante 48 dias, onde a vinhaça foi adicionada a uma concentração de 33 mL.Kg-1 de solo. A eficiência de biodegradação também foi medida pela quantificação de hidrocarbonetos totais de petróleo (TPH por cromatografia gasosa. A biorremediação da água subterrânea foi realizada em experimentos laboratoriais simulando condições aeradas (bioreatores e não aeradas (frascos de DBO. Em ambos os casos, a concentração de vinhaça foi de 5 % (v/v e diferentes parâmetros f

Laboratory studies on natural restoration of ground water after in-situ leach uranium mining

International Nuclear Information System (INIS)

Bell, N.E.; Deutsch, W.J.; Serne, R.J.

1983-05-01

When uranium is mined using in-situ leach techniques, the chemical quality of the ground water in the ore-zone aquifer is affected. This could lead to long-term degradation of the ground water if restoration techniques are not applied after the leaching is completed. Pacific Northwest Laboratory (PNL), is conducting an NRC-sponsored research project on natural restoration and induced-restoration techniques. Laboratory studies were designed to evaluate the ability of the natural system (ore-zone sediments and groundwater) to mitigate the effects of mining on aquifer chemistry. Using batch and flow-through column experiments [performed with lixiviant (leaching solution) and sediments from the reduced zone of an ore-zone aquifer], we found that the natural system can lower uranium and bicarbonate concentrations in solutions and reduce the lixiviant redox potential (Eh). The change in redox potential could cause some of the contaminants that were dissolved during the uranium leaching operation to precipitate, thereby lowering their solution concentration. The concentrations of other species such as calcium, potassium, and sulfate increased, possibly as a result of mineral dissolution and ion exchange. In this paper, we describe the experimentally determined mobility of contaminants after in-situ leach mining, and discuss the possible chemical process affecting mobility

Laboratory studies on natural restoration of ground water after in-situ leach uranium mining

Energy Technology Data Exchange (ETDEWEB)

Bell, N.E.; Deutsch, W.J.; Serne, R.J.

1983-05-01

When uranium is mined using in-situ leach techniques, the chemical quality of the ground water in the ore-zone aquifer is affected. This could lead to long-term degradation of the ground water if restoration techniques are not applied after the leaching is completed. Pacific Northwest Laboratory (PNL), is conducting an NRC-sponsored research project on natural restoration and induced-restoration techniques. Laboratory studies were designed to evaluate the ability of the natural system (ore-zone sediments and groundwater) to mitigate the effects of mining on aquifer chemistry. Using batch and flow-through column experiments (performed with lixiviant (leaching solution) and sediments from the reduced zone of an ore-zone aquifer), we found that the natural system can lower uranium and bicarbonate concentrations in solutions and reduce the lixiviant redox potential (Eh). The change in redox potential could cause some of the contaminants that were dissolved during the uranium leaching operation to precipitate, thereby lowering their solution concentration. The concentrations of other species such as calcium, potassium, and sulfate increased, possibly as a result of mineral dissolution and ion exchange. In this paper, we describe the experimentally determined mobility of contaminants after in-situ leach mining, and discuss the possible chemical process affecting mobility.

The development and application of engineered proteins for bioremediation

Energy Technology Data Exchange (ETDEWEB)

Trewhella, J. [ed.

1995-09-26

Clean up of the toxic legacy of the Cold War is projected to be the most expensive domestic project the nation has yet undertaken. Remediation of the Department of Energy and Department of Defense toxic waste sites alone are projected to cost {approximately}$1 trillion over a 20-30 year period. New, cost effective technologies are needed to attack this enormous problem. Los Alamos has put together a cross-divisional team of scientist to develop science based bioremediation technology to work toward this goal. In the team we have expertise in: (1) molecular, ecosystem and transport modeling; (2) genetic and protein engineering; (3) microbiology and microbial ecology; (4) structural biology; and (5) bioinorganic chemistry. This document summarizes talks at a workshop of different aspects of bioremediation technology including the following: Introducing novel function into a Heme enzyme: engineering by excavation; cytochrome P-450: ideal systems for bioremediation?; selection and development of bacterial strains for in situ remediation of cholorinated solvents; genetic analysis and preparation of toluene ortho-monooxygenase for field application in remediation of trichloroethylene; microbial ecology and diversity important to bioremediation; engineering haloalkane dehalogenase for bioremediation; enzymes for oxidative biodegradation; indigenous bacteria as hosts for engineered proteins; performance of indigenous bacterial, hosting engineered proteins in microbial communities.

Novel Sensor for the In Situ Measurement of Uranium Fluxes

Energy Technology Data Exchange (ETDEWEB)

Hatfield, Kirk [Univ. of Florida, Gainesville, FL (United States)

2015-02-10

The goal of this project was to develop a sensor that incorporates the field-tested concepts of the passive flux meter to provide direct in situ measures of flux for uranium and groundwater in porous media. Measurable contaminant fluxes [J] are essentially the product of concentration [C] and groundwater flux or specific discharge [q ]. The sensor measures [J] and [q] by changes in contaminant and tracer amounts respectively on a sorbent. By using measurement rather than inference from static parameters, the sensor can directly advance conceptual and computational models for field scale simulations. The sensor was deployed in conjunction with DOE in obtaining field-scale quantification of subsurface processes affecting uranium transport (e.g., advection) and transformation (e.g., uranium attenuation) at the Rifle IFRC Site in Rifle, Colorado. Project results have expanded our current understanding of how field-scale spatial variations in fluxes of uranium, groundwater and salient electron donor/acceptors are coupled to spatial variations in measured microbial biomass/community composition, effective field-scale uranium mass balances, attenuation, and stability. The coupling between uranium, various nutrients and micro flora can be used to estimate field-scale rates of uranium attenuation and field-scale transitions in microbial communities. This research focuses on uranium (VI), but the sensor principles and design are applicable to field-scale fate and transport of other radionuclides. Laboratory studies focused on sorbent selection and calibration, along with sensor development and validation under controlled conditions. Field studies were conducted at the Rifle IFRC Site in Rifle, Colorado. These studies were closely coordinated with existing SBR (formerly ERSP) projects to complement data collection. Small field tests were conducted during the first two years that focused on evaluating field-scale deployment procedures and validating sensor performance under

Identification of groundwater microorganisms capable of assimilating RDX-derived nitrogen during in-situ bioremediation

Energy Technology Data Exchange (ETDEWEB)

Cho, Kun-Ching [Zachry Department of Civil Engineering, Texas A& M University, College Station, TX 77843-3136 (United States); Fuller, Mark E.; Hatzinger, Paul B. [CB& I Federal Services, Lawrenceville, NJ 08648 (United States); Chu, Kung-Hui, E-mail: kchu@civil.tamu.edu [Zachry Department of Civil Engineering, Texas A& M University, College Station, TX 77843-3136 (United States)

2016-11-01

Hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), a nitroamine explosive, is commonly detected in groundwater at military testing and training sites. The objective of this study was to characterize the microbial community capable of using nitrogen derived from the RDX or RDX intermediates during in situ bioremediation. Active groundwater microorganisms capable of utilizing nitro-, ring- or fully-labeled {sup 15}N-RDX as a nitrogen source were identified using stable isotope probing (SIP) in groundwater microcosms prepared from two wells in an aquifer previously amended with cheese whey to promote RDX biodegradation. A total of fifteen 16S rRNA gene sequences, clustered in Clostridia, β-Proteobacteria, and Spirochaetes, were derived from the {sup 15}N-labeled DNA fractions, suggesting the presence of metabolically active bacteria capable of using RDX and/or RDX intermediates as a nitrogen source. None of the derived sequences matched RDX-degrading cultures commonly studied in the laboratory, but some of these genera have previously been linked to RDX degradation in site groundwater via {sup 13}C-SIP. When additional cheese whey was added to the groundwater samples, 28 sequences grouped into Bacteroidia, Bacilli, and α-, β-, and γ-Proteobacteria were identified. The data suggest that numerous bacteria are capable of incorporating N from ring- and nitro-groups in RDX during anaerobic bioremediation, and that some genera may be involved in both C and N incorporation from RDX. - Highlights: • Cheese whey addition resulted in 28 different clones associated with RDX degradation. • The 28 clones belong to Bacteroidia, Bacilli, and α-, β-, and γ-Proteobacteria. • SIP identified 15 clones using RDX and/or its metabolites as a nitrogen source. • The clones clustered in Clostridia, β-Proteobacteria, and Spirochaetes.

Identification of groundwater microorganisms capable of assimilating RDX-derived nitrogen during in-situ bioremediation

International Nuclear Information System (INIS)

Cho, Kun-Ching; Fuller, Mark E.; Hatzinger, Paul B.; Chu, Kung-Hui

2016-01-01

Hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), a nitroamine explosive, is commonly detected in groundwater at military testing and training sites. The objective of this study was to characterize the microbial community capable of using nitrogen derived from the RDX or RDX intermediates during in situ bioremediation. Active groundwater microorganisms capable of utilizing nitro-, ring- or fully-labeled "1"5N-RDX as a nitrogen source were identified using stable isotope probing (SIP) in groundwater microcosms prepared from two wells in an aquifer previously amended with cheese whey to promote RDX biodegradation. A total of fifteen 16S rRNA gene sequences, clustered in Clostridia, β-Proteobacteria, and Spirochaetes, were derived from the "1"5N-labeled DNA fractions, suggesting the presence of metabolically active bacteria capable of using RDX and/or RDX intermediates as a nitrogen source. None of the derived sequences matched RDX-degrading cultures commonly studied in the laboratory, but some of these genera have previously been linked to RDX degradation in site groundwater via "1"3C-SIP. When additional cheese whey was added to the groundwater samples, 28 sequences grouped into Bacteroidia, Bacilli, and α-, β-, and γ-Proteobacteria were identified. The data suggest that numerous bacteria are capable of incorporating N from ring- and nitro-groups in RDX during anaerobic bioremediation, and that some genera may be involved in both C and N incorporation from RDX. - Highlights: • Cheese whey addition resulted in 28 different clones associated with RDX degradation. • The 28 clones belong to Bacteroidia, Bacilli, and α-, β-, and γ-Proteobacteria. • SIP identified 15 clones using RDX and/or its metabolites as a nitrogen source. • The clones clustered in Clostridia, β-Proteobacteria, and Spirochaetes

Aquifer restoration at in-situ leach uranium mines: evidence for natural restoration processes

International Nuclear Information System (INIS)

Deutsch, W.J.; Serne, R.J.; Bell, N.E.; Martin, W.J.

1983-04-01

Pacific Northwest Laboratory conducted experiments with aquifer sediments and leaching solution (lixiviant) from an in-situ leach uranium mine. The data from these laboratory experiments and information on the normal distribution of elements associated with roll-front uranium deposits provide evidence that natural processes can enhance restoration of aquifers affected by leach mining. Our experiments show that the concentration of uranium (U) in solution can decrease at least an order of magnitude (from 50 to less than 5 ppM U) due to reactions between the lixiviant and sediment, and that a uranium solid, possibly amorphous uranium dioxide, (UO 2 ), can limit the concentration of uranium in a solution in contact with reduced sediment. The concentrations of As, Se, and Mo in an oxidizing lixiviant should also decrease as a result of redox and precipitation reactions between the solution and sediment. The lixiviant concentrations of major anions (chloride and sulfate) other than carbonate were not affected by short-term (less than one week) contact with the aquifer sediments. This is also true of the total dissolved solids level of the solution. Consequently, we recommend that these solution parameters be used as indicators of an excursion of leaching solution from the leach field. Our experiments have shown that natural aquifer processes can affect the solution concentration of certain constituents. This effect should be considered when guidelines for aquifer restoration are established

Use of gene probes to assess the impact and effectiveness of aerobic in situ bioremediation of TCE

Energy Technology Data Exchange (ETDEWEB)

Hazen, Terry C.; Chakraborty, Romy; Fleming, James M.; Gregory, Ingrid R.; Bowman, John P.; Jimenez, Luis; Zhang, Dai; Pfiffner, Susan M.; Brockman, Fred J.; Sayler, Gary S.

2009-03-15

Gene probe hybridization was used to determine distribution and expression of co-metabolic genes at a contaminated site as it underwent in situ methanotrophic bioremediation of trichloroethylene (TCE). The bioremediation strategies tested included a series of air, air:methane, and air:methane:nutrient pulses of the test plot using horizontal injection wells. During the test period, the levels of TCE reduced drastically in almost all test samples. Sediment core samples (n = 367) taken from 0 m (surface)-43 m depth were probed for gene coding for methanotrophic soluble methane monooxygenase (sMMO) and heterotrophic toluene dioxygenase (TOD), which are known to co-metabolize TCE. The same sediment samples were also probed for genes coding for methanol dehydrogenase (MDH) (catalyzing the oxidation of methanol to formaldehyde) to assess specifically changes in methylotrophic bacterial populations in the site. Gene hybridization results showed that the frequency of detection of sMMO genes were stimulated approximately 250% following 1% methane:air (v/v) injection. Subsequent injection of 4% methane:air (v/v) resulted in an 85% decline probably due to nutrient limitations, since addition of nutrients (gaseous nitrogen and phosphorus) thereafter caused an increase in the frequency of detection of sMMO genes. Detection of TOD genes declined during the process, and eventually they were non-detectable by the final treatment, suggesting that methanotrophs displaced the TOD gene containing heterotrophs. Active transcription of sMMO and TOD was evidenced by hybridization to mRNA. These analyses combined with results showing the concomitant decline in TCE concentrations, increases in chloride concentration and increases in methanotroph viable counts, provide multiple lines of evidence that TCE remediation was caused specifically by methanotrophs. Our results suggest that sMMO genes are responsible for most, if not all, of the observed biodegradation of TCE. This study

Microbial reduction of uranium(VI) by anaerobic microorganisms isolated from a former uranium mine

Energy Technology Data Exchange (ETDEWEB)

Gerber, Ulrike; Krawczyk-Baersch, Evelyn [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Biogeochemistry; Arnold, Thuro [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Inst. of Resource Ecology; Scheinost, Andreas C. [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Molecular Structures

2017-06-01

The former uranium mine Koenigstein (Germany) is currently in the process of controlled flooding by reason of remediation purposes. However, the flooding water still contains high concentrations of uranium and other heavy metals. For that reason the water has to be cleaned up by a conventional waste water treatment plant. The aim of this study was to investigate the interactions between anaerobic microorganisms and uranium for possible bioremediation approaches, which could be an great alternative for the intensive and expensive waste water treatment. EXAFS (extended X-ray absorption fine structure) and XANES (X-ray absorption near edge structure) measurements were performed and revealed a complete reduction of U(VI) to U(IV) only by adding 10 mM glycerol.

Microbial reduction of uranium(VI) by anaerobic microorganisms isolated from a former uranium mine

International Nuclear Information System (INIS)

Gerber, Ulrike; Krawczyk-Baersch, Evelyn; Arnold, Thuro; Scheinost, Andreas C.

2017-01-01

The former uranium mine Koenigstein (Germany) is currently in the process of controlled flooding by reason of remediation purposes. However, the flooding water still contains high concentrations of uranium and other heavy metals. For that reason the water has to be cleaned up by a conventional waste water treatment plant. The aim of this study was to investigate the interactions between anaerobic microorganisms and uranium for possible bioremediation approaches, which could be an great alternative for the intensive and expensive waste water treatment. EXAFS (extended X-ray absorption fine structure) and XANES (X-ray absorption near edge structure) measurements were performed and revealed a complete reduction of U(VI) to U(IV) only by adding 10 mM glycerol.

Bioremediation without earth moving. Biologische Altlastensanierung ohne Erdaushub

Energy Technology Data Exchange (ETDEWEB)

Franz, B; Knapp, A; Mueller, D

1992-05-01

According to rough estimates, there are 70,000 sites in the pre-unification Federal Republic of Germany where contamination is suspected. Some 50 to 60% of the contaminated sites are suitable for bioremediation. The Bioux-S process permits in-situ cleanup without any need for complicated and expensive earth moving operations. The culture conditions of the aerobic microorganisms already present in the soil are improved by the introduction of pure oxygen and special nutrients. Such microorganisms are already ideally adapted to the contaminants present and utilise them partly as nutrients and partly to maintain their energy balance. The process has already been successfully used for bioremediation of refinery and gasworks as well as chemical production sites. (orig.).

Hanford Site 100-N Area In Situ Bioremediation of UPR-100-N-17, Deep Petroleum Unplanned Release - 13245

International Nuclear Information System (INIS)

Saueressig, Daniel G.

2013-01-01

In 1965 and 1966, approximately 303 m 3 of Number 2 diesel fuel leaked from a pipeline used to support reactor operations at the Hanford Site's N Reactor. N Reactor was Hanford's longest operating reactor and served as the world's first dual purpose reactor for military and power production needs. The Interim Action Record of Decision for the 100-N Area identified in situ bioremediation as the preferred alternative to remediate the deep vadose zone contaminated by this release. A pilot project supplied oxygen into the vadose zone to stimulate microbial activity in the soil. The project monitored respiration rates as an indicator of active biodegradation. Based on pilot study results, a full-scale system is being constructed and installed to remediate the vadose zone contamination. (authors)

Remediation of Soil Contaminated with Uranium using a Biological Method

International Nuclear Information System (INIS)

Park, Hye Min; Kim, Gye Nam; Shon, Dong Bin; Lee, Ki Won; Chung, Un Soo; Moon, Jai Kwon

2011-01-01

Bioremediation is a method to cleanup contaminants in soil or ground water with microorganisms. The biological method can reduce the volume of waste solution and the construction cost and operation cost of soil remediation equipment. Bioremediation can be divided into natural attenuation, bioaugmentation, biostimulation. Biostimulation is technology to improve natural purification by adding nutritional substances, supplying oxygen and controlling pH. In this study, penatron, that is a nutritional substances, was mixed with soil. Optimum conditions for mixing ratios of penatron and soil, and the pH of soil was determined through several bioremediation experiments with soil contaminated with uranium. Also, under optimum experiment conditions, the removal efficiencies of soil and concrete according to reaction time were measured for feasibility analysis of soil and concrete bioremediations

Bioremediation of contaminated soil: Strategy and case histories

International Nuclear Information System (INIS)

Balba, M.T.; Ying, A.C.; McNeice, T.G.

1991-01-01

Microorganisms are capable of degrading many kinds of xenobiotic compounds and toxic chemicals. These microorganisms are ubiquitous in nature and there are numerous cases in which long-term contamination of soil and groundwater has been observed. The persistence of the contamination is usually caused by the inability of micro-organisms to metabolize these compounds under the prevailing environmental conditions. Two general reasons account for the failure of microbes to degrade pollutants in any environment: (1) inherent molecular recalcitrance of the contaminants and (2) environmental factors. The inherent molecular recalcitrance is usually associated with xenobiotic compounds where the chemical structure of the molecule is such that microbes and enzymes required for its catabolism have not evolved yet in nature. The environmental factors include a range of physicochemical conditions which influence microbial growth and activity. Biological remediation of contaminated sites can be accomplished using naturally-occurring microorganisms to treat the contaminants. Only particular groups of microorganisms are capable of decomposing specific compounds. The development of a bioremediation program for a specific contaminated soil system usually includes: thorough site/soil/waste characterization; treatability studies; and design and implementation of the bioremediation plan. The results of in situ and ex situ treatment programs involving the cleanup of petroleum hydrocarbon-contaminated soil will be discussed in detail. The paper will address key issues affecting the success of the bioremediation process such as nutrient transport, metal precipitation and potential soil clogging, microbial inoculation, etc

Uranium biomineralization by a metal resistant Pseudomonas aeruginosa strain isolated from contaminated mine waste.

Science.gov (United States)

Choudhary, Sangeeta; Sar, Pinaki

2011-02-15

Uranium biomineralization by a metal-resistant Pseudomonas aeruginosa strain isolated from uranium mine waste was characterized for its potential in bioremediation. Uranium resistance, its cellular localization and chemical nature of uranium-bacteria interaction were elucidated. Survival and uranium biomineralization from mine water were investigated using microcosm experiments. The selected bacterium showed U resistance and accumulation (maximum of 275 mg U g(-1)cell dry wt.) following incubation in 100 mg U L(-1), pH 4.0, for 6 h. Transmission electron microscopy and X-ray diffraction analyses revealed that bioaccumulated uranium was deposited within the cell envelope as needle shaped U-phosphate compounds that attain crystallinity only at pH 4.0. A synergistic involvement of deprotonated phosphate and carboxyl moieties in facilitating bioprecipitation of uranium was evident from FTIR analysis. Based on these findings we attribute the localized U sequestration by this bacterium as innocuous complex to its possible mechanism of uranium resistance. Microcosm data confirmed that the strain can remove soluble uranium (99%) and sequester it as U oxide and phosphate minerals while maintaining its viability. The study showed that indigenous bacteria from contaminated site that can survive uranium and other heavy metal toxicity and sequester soluble uranium as biominerals could play important role in uranium bioremediation. Copyright © 2010 Elsevier B.V. All rights reserved.

Recovery of microbial diversity and activity during bioremediation following chemical oxidation of diesel contaminated soils

NARCIS (Netherlands)

Sutton, N.B.; Langenhoff, A.A.M.; Hidalgo Lasso, D.; Zaan, van der B.M.; Gaans, van P.; Maphosa, F.; Smidt, H.; Grotenhuis, J.T.C.; Rijnaarts, H.H.M.

2014-01-01

To improve the coupling of in situ chemical oxidation and in situ bioremediation, a systematic analysis was performed of the effect of chemical oxidation with Fenton's reagent, modified Fenton's reagent, permanganate, or persulfate, on microbial diversity and activity during 8 weeks of incubation in

The evaluation of in-situ leaching hydrological-geologic condition in a sandstone-type uranium deposits of a low-grade and thick ledge

International Nuclear Information System (INIS)

Jiang Yan

2014-01-01

The ore aquifer of a sandstone-type uranium deposits is thick, the grade, and uranium amount per square meter is low. To demonstrate the economic rationality of the in-situ leaching deposit, the Pumping test on the spot, recovery of water levels test, Pumping test and Injection test, Injection test in a Drilling hole, the pumping and injection balance test are carried out. And the hydro geological parameters of mineral aquifer are acquired. The parameters includes coefficient of transmissibility, Coefficient of permeability, Specific discharge of a well and Water injection. Radius of influence etc. The relation between discharge of drilling and Drawdown is researched. The capability of pumping and injection by a drilling hole is determined. The Hydraulic between the aquifer with mineral and the upper and lower aquifer is researched. The reasonable Mining drawdown is testified, the hydrogeological conditions of in-Situ leaching of the mining deposit is found out, this provides necessary parameters and basis for this kind of Situ-leach uranium mining wells, the designing of Spacing of wells, and the economic evaluation of In-situ leaching technology. (author)

Some factors affecting agitation leach test during in-situ leaching of uranium

International Nuclear Information System (INIS)

Liao Wensheng; Jiang Yan; Wang Limin; Shi Zhenfeng; Zhao Qiaofu; MARMAR

2014-01-01

The agitation leaching test is one of the most fundamental research works in in-situ leaching of uranium. Some factors affecting the test results were analyzed including stirring, leaching time, oxidizer used in alkaline leach, washing solution, the amount and size of ore samples. The results indicate that stirring can enhance diffusion velocity. The leach time l or 2 days is suitable for the samples containing accessible uranium and low acid consumption minerals; whereas 3 or 4 days for those containing refractory ore to leach and slowly acid consuming minerals. For the oxidizer used in alkaline leach, potassium permanganate is better than hydrogen peroxide. Recovery calculated by the leach solution can be directly obtained by its uranium level and the original volume of lixiviant without analyzing and calculating the washing solution. The appropriate amount and size of ore samples for the agitation leaching test are 60 g and <1 mm. By controlling the above factors, the agitation leach test can improve the applicability of the different ore samples and give the more reliable data. (authors)

An investigation of the potential for in situ bioremediation of oil sands tailings

International Nuclear Information System (INIS)

Herman, D.C.; Costerton, J.W.; Fedorak, P.M.; Mackinnon, M.D.

1993-01-01

Oil sand tailings water has been shown to be acutely toxic to aquatic organisms. Naphthenic acids have been shown to be the primary source of this toxicity within oil sand tailings waste. The potential for in-situ bioremediation of oil sand tailings was investigated by determining the ability of indigenous bacteria to biodegrade naphthenic acids. A mixed bacterial culture enriched from oil sand tailings was found to be capable of growth on a commercially available naphthenic acid mixture. When sodium naphthenates (30 mg/l) were added to a minimal salts medium and inoculated with the mixed bacterial culture, gas chromatography revealed that many components of the naphthenic acid mixture were biodegraded within eight days of incubation. The same culture was also tested against the naphthenic acid fraction extracted directly from oil sand tailings. The tailings extract was diluted into the minimal salts medium in sealed flasks and inoculated with the enrichment culture. The production of CO 2 indicated microbial mineralization of components within the oil sands extract. Microtox analysis determined that microbial activity resulted in a reduction in the acute toxicity of the tailings extract. 5 refs., 3 figs

Reverse osmosis treatment in CO_2 + O_2 to the application of the in-situ leaching of uranium

International Nuclear Information System (INIS)

Ruan Zhilong; Li Xilong; Yang Shaowu

2014-01-01

Advantages and disadvantages of various groundwater management methods, combined with CO_2 + O_2 characteristics of in situ leaching uranium mining process, use reverse osmosis wastewater treatment technology, has carried on the laboratory test, field condition test and industrial test. Obtained by indoor experiment and field conditions for Cl"- ion concentration variation characteristics; Reverse osmosis treatment effect of wastewater is verified by industrial test, obtained the technical parameters and consumption data, as well as the leaching liquid and adsorption tail liquid pH, SO_4"2"-; Cl"- in the plasma concentration monitoring, and further prove that the reverse osmosis treatment technology is suitable for in-situ leaching of uranium in CO_2 + O_2 in wastewater treatment. (authors)

Field Evaluation of the Restorative Capacity of the Aquifer Downgradient of a Uranium In-Situ Recovery Mining Site

Energy Technology Data Exchange (ETDEWEB)

Reimus, Paul William [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-05-22

A two-part field study was conducted in Smith Ranch-Highland in-situ recovery (ISR) near Douglas, Wyoming, to evaluate the restorative capacity of the aquifer downgradient (i.e., hydrologically downstream) of a Uranium ISR mining site with respect to the transport of uranium and other potential contaminants in groundwater after mining has ceased. The study was partially conducted by checking the Uranium content and the alkalinity of separate wells, some wells had been restored and others had not. A map and in-depth procedures of the study are included.

Streamline-concentration balance model for in-situ uranium leaching and site restoration

International Nuclear Information System (INIS)

Bommer, P.M.; Schechter, R.S.; Humenick, M.J.

1981-03-01

This work presents two computer models. One describes in-situ uranium leaching and the other describes post leaching site restoration. Both models use a streamline generator to set up the flow field over the reservoir. The leaching model then uses the flow data in a concentration balance along each streamline coupled with the appropriate reaction kinetics to calculate uranium production. The restoration model uses the same procedure except that binary cation exchange is used as the restoring mechanism along each streamline and leaching cation clean up is simulated. The mathematical basis for each model is shown in detail along with the computational schemes used. Finally, the two models have been used with several data sets to point out their capabilities and to illustrate important leaching and restoration parameters and schemes

Streamline-concentration balance model for in situ uranium leaching and site restoration

International Nuclear Information System (INIS)

Bommer, P.M.

1979-01-01

This work presents two computer models. One describes in situ uranium leaching and the other describes post leaching site restoration. Both models use a streamline generator to set up the flow field over the reservoir. The leaching model then uses the flow data in a concentration balance along each streamline coupled with the appropriate reaction kinetics to calculate uranium production. The restoration model uses the same procedure ecept that binary cation exchange is used as the restoring mechanism along each streamline and leaching cation clean up is stimulated. The mathematical basis for each model is shown in detail along with the computational schemes used. Finally, the two models have been used with several data sets to point out their capabilities and to illustrate important leaching and restoration parameters and schemes

In situ production of bio-surfactants: An alternative method for dispersing and bioremediating marine oil spills

International Nuclear Information System (INIS)

Josefsen, K.D.; Sveum, P.; Ramstad, P.; Markussen, S.; Folkvord, K.; Krigsvoll, K.; Aune, R.; Storroe, I.

1995-01-01

Some oil degrading bacteria are able to produce surfactants. These biosurfactants enhance dispersion of oil droplets into the water column. A large number of surfactant producing bacterial strains have been isolated from seawater samples collected at different sites around the world. Strains isolated from seawater samples collected in cold regions generally had better properties than strains isolated from warm seawater. Many of the isolated strains were able to disperse crude oils with a large variation of composition, as well as the water-in-emulsion (chocolate mousse) formed during weathering of crude oil in the sea. The results show that in situ application of surfactant producing bacteria can be a viable tool in future oil spill contingency, and that dispersion of oil may increase the biodegradation rate. Work is in progress to examine the use of such bacteria in the bioremediation of oil contaminated shorelines. 10 refs., 3 figs., 2 tabs

Using proteomic data to assess a genome-scale "in silico" model of metal reducing bacteria in the simulation of field-scale uranium bioremediation

Science.gov (United States)

Yabusaki, S.; Fang, Y.; Wilkins, M. J.; Long, P.; Rifle IFRC Science Team

2011-12-01

A series of field experiments in a shallow alluvial aquifer at a former uranium mill tailings site have demonstrated that indigenous bacteria can be stimulated with acetate to catalyze the conversion of hexavalent uranium in a groundwater plume to immobile solid-associated uranium in the +4 oxidation state. While this bioreduction of uranium has been shown to lower groundwater concentrations below actionable standards, a viable remediation methodology will need a mechanistic, predictive and quantitative understanding of the microbially-mediated reactions that catalyze the reduction of uranium in the context of site-specific processes, properties, and conditions. At the Rifle IFRC site, we are investigating the impacts on uranium behavior of pulsed acetate amendment, acetate-oxidizing iron and sulfate reducing bacteria, seasonal water table variation, spatially-variable physical (hydraulic conductivity, porosity) and geochemical (reactive surface area) material properties. The simulation of three-dimensional, variably saturated flow and biogeochemical reactive transport during a uranium bioremediation field experiment includes a genome-scale in silico model of Geobacter sp. to represent the Fe(III) terminal electron accepting process (TEAP). The Geobacter in silico model of cell-scale physiological metabolic pathways is comprised of hundreds of intra-cellular and environmental exchange reactions. One advantage of this approach is that the TEAP reaction stoichiometry and rate are now functions of the metabolic status of the microorganism. The linkage of in silico model reactions to specific Geobacter proteins has enabled the use of groundwater proteomic analyses to assess the accuracy of the model under evolving hydrologic and biogeochemical conditions. In this case, the largest predicted fluxes through in silico model reactions generally correspond to high abundances of proteins linked to those reactions (e.g. the condensation reaction catalyzed by the protein

Factoring uncertainty into restoration modeling of in-situ leach uranium mines

Science.gov (United States)

Johnson, Raymond H.; Friedel, Michael J.

2009-01-01

Postmining restoration is one of the greatest concerns for uranium in-situ leach (ISL) mining operations. The ISL-affected aquifer needs to be returned to conditions specified in the mining permit (either premining or other specified conditions). When uranium ISL operations are completed, postmining restoration is usually achieved by injecting reducing agents into the mined zone. The objective of this process is to restore the aquifer to premining conditions by reducing the solubility of uranium and other metals in the ground water. Reactive transport modeling is a potentially useful method for simulating the effectiveness of proposed restoration techniques. While reactive transport models can be useful, they are a simplification of reality that introduces uncertainty through the model conceptualization, parameterization, and calibration processes. For this reason, quantifying the uncertainty in simulated temporal and spatial hydrogeochemistry is important for postremedial risk evaluation of metal concentrations and mobility. Quantifying the range of uncertainty in key predictions (such as uranium concentrations at a specific location) can be achieved using forward Monte Carlo or other inverse modeling techniques (trial-and-error parameter sensitivity, calibration constrained Monte Carlo). These techniques provide simulated values of metal concentrations at specified locations that can be presented as nonlinear uncertainty limits or probability density functions. Decisionmakers can use these results to better evaluate environmental risk as future metal concentrations with a limited range of possibilities, based on a scientific evaluation of uncertainty.

Monitoring bioremediation of weathered diesel NAPL using oxygen depletion profiles

International Nuclear Information System (INIS)

Davis, G.B.; Johnston, C.D.; Patterson, B.M.; Barber, C.; Bennett, M.

1995-01-01

Semicontinuous logging of oxygen concentrations at multiple depths has been used to evaluate the progress of an in situ bioremediation trial at a site contaminated by weathered diesel nonaqueous-phase liquid (NAPL). The evaluation trial consisted of periodic addition of nutrients and aeration of a 100-m 2 trial plot. During the bioremediation trial, aeration was stopped periodically, and decreases in dissolved and gaseous oxygen concentrations were monitored using data loggers attached to in situ oxygen sensors placed at multiple depths above and within a thin NAPL-contaminated zone. Oxygen usage rate coefficients were determined by fitting zero- and first-order rate equations to the oxygen depletion curves. For nutrient-amended sites within the trial plot, estimates of oxygen usage rate coefficients were significantly higher than estimates from unamended sites. These rates also converted to NPL degradation rates, comparable to those achieved in previous studies, despite the high concentrations and weathered state of the NAPL at this test site

Bioassays with caged hyalella azteca to determine in situ toxicity downstream of two Saskatchewan, Canada, uranium operations.

Science.gov (United States)

Robertson, Erin L; Liber, Karsten

2007-11-01

The main objectives of this in situ study were to evaluate the usefulness of an in situ bioassay to determine if downstream water bodies at the Key Lake and Rabbit Lake uranium operations (Saskatchewan, Canada) were toxic to Hyalella azteca and, if toxicity was observed, to differentiate between the contribution of surface water and sediment contamination to in situ toxicity. These objectives were achieved by performing 4-d in situ bioassays with laboratory-reared H. azteca confined in specially designed, paired, surface water and sediment exposure chambers. Results from the in situ bioassays revealed significant mortality, relative to the respective reference site, at the exposure sites at both Key Lake (p situ mortality of H. azteca at both operations, although this relationship was stronger at Key Lake. At Key Lake, the primary cause of aquatic toxicity to H. azteca did not appear to be correlated with the variables measured in this study, but most likely with a pulse of organic mill-process chemicals released during the time of the in situ study-a transient event that was caused by a problem with the mill's solvent extraction process. The suspected cause of in situ toxicity to H. azteca at Rabbit Lake was high levels of uranium in surface water, sediment, and pore water.

Characterization of nano-bubbles as an oxygen carrier for in-situ bioremediation of organic pollutants in the subsurface

Science.gov (United States)

KIM, E.; Jung, J.; Kang, S.; Choi, Y.

2016-12-01

In-situ bioremediation using bubbles as an oxygen carrier has shown its applicability for aerobic biodegradation of organic pollutants in the subsurface. By recent progresses, generation of nano-sized bubbles is possible, which have enhanced oxygen transfer efficiencies due to their high interfacial area and stability. We are developing an in-situ bioremediation technique using nano-bubbles as an oxygen carrier. In this study, nano-bubbles were characterized for their size and oxygen supply capacity. Nano-bubbles were generated with pure oxygen and pure helium gas. The stable nano-bubbles suspended in water were sonicated to induce the bubbles to coalesce, making them to rise and be released out of the water. By removing the bubbles, the water volume was decreased by 0.006%. The gas released from the bubble suspension was collected to measure the amount of gas in the nano-bubbles. For sparingly soluble helium gas 17.9 mL/L was released from the bubble suspension, while for oxygen 46.2 mL/L was collected. For the oxygen nano-bubble suspension, it is likely that the release of dissolved oxygen (DO) contributed to the collected gas volume. After removing the oxygen nano-bubbles, 36.0 mg/L of DO was still present in water. Altogether, the oxygen nano-bubble suspension was estimated to have 66.2 mg/L of oxygen in a dissolved form and 25.6 mg/L as nano-bubbles. A high DO level in the water was possible because of their large Laplace pressure difference across the fluid interface. Applying Young-Laplace equation and ideal gas law, the bubble diameter was estimated to be approximately 10 nm, having an internal pressure of 323 atm. Considering the saturation DO of 8.26 mg/L for water in equilibrium with the atmosphere, the total oxygen content of 91.8 mg/L in the nano-bubble suspension suggests its great potential as an oxygen carrier. Studies are underway to verify the enhanced aerobic biodegradation of organic pollutants in soils by injecting nano-bubble suspensions.

Soil bioremediation at CFB Trenton: evaluation of bioremediation processes

International Nuclear Information System (INIS)

Ouellette, L.; Cathum, S.; Avotins, J.; Kokars, V.; Cooper, D.

1996-01-01

Bioremediation processes and their application in the cleanup of contaminated soil, were discussed. The petroleum contaminated soil at CFB Trenton, was evaluated to determine which bioremediation process or combination of processes would be most effective. The following processes were considered: (1) white hot fungus, (2) Daramend proprietary process, (3) composting, (4) bioquest proprietary bioremediation processes, (5) Hobbs and Millar proprietary bioremediation process, and (6) farming. A brief summary of each of these options was included. The project was also used as an opportunity to train Latvian and Ukrainian specialists in Canadian field techniques and laboratory analyses. Preliminary data indicated that bioremediation is a viable method for treatment of contaminated soil. 18 refs., 3 figs

An evaluation of health risk to the public as a consequence of in situ uranium mining in Wyoming, USA.

Science.gov (United States)

Ruedig, Elizabeth; Johnson, Thomas E

2015-12-01

In the United States there is considerable public concern regarding the health effects of in situ recovery uranium mining. These concerns focus principally on exposure to contaminants mobilized in groundwater by the mining process. However, the risk arising as a result of mining must be viewed in light of the presence of naturally occurring uranium ore and other constituents which comprise a latent hazard. The United States Environmental Protection Agency recently proposed new guidelines for successful restoration of an in situ uranium mine by limiting concentrations of thirteen groundwater constituents: arsenic, barium, cadmium, chromium, lead, mercury, selenium, silver, nitrate (as nitrogen), molybdenum, radium, total uranium, and gross α activity. We investigated the changes occurring to these constituents at an ISR uranium mine in Wyoming, USA by comparing groundwater quality at baseline measurement to that at stability (post-restoration) testing. Of the groundwater constituents considered, only uranium and radium-226 showed significant (p < 0.05) deviation from site-wide baseline conditions in matched-wells. Uranium concentrations increased by a factor of 5.6 (95% CI 3.6-8.9 times greater) while radium-226 decreased by a factor of about one half (95% CI 0.42-0.75 times less). Change in risk was calculated using the RESRAD (onsite) code for an individual exposed as a resident-farmer; total radiation dose to a resident farmer decreased from pre-to post-mining by about 5.2 mSv y(-1). Higher concentrations of uranium correspond to increased biomarkers of nephrotoxicity, however the clinical significance of this increase is unclear. Published by Elsevier Ltd.

Uranium Mobility During In Situ Redox Manipulation of the 100 Areas of the Hanford Site

International Nuclear Information System (INIS)

Resch, C.T.; Szecsody, J.E.; Fruchter, J.S.; Cantrell, K.J.; Krupka, K.M.; Williams, M.D.

1998-01-01

A series of laboratory experiments and computer simulations was conducted to assess the extent of uranium remobilization that is likely to occur at the end of the life cycle of an in situ sediment reduction process. The process is being tested for subsurface remediation of chromate- and chlorinated solvent-contaminated sediments at the Hanford Site in southeastern Washington. Uranium species that occur naturally in the +6 valence state ∼(VI) at 10 ppb in groundwater at Hanford will accumulate as U(N) through the reduction and subsequent precipitation conditions of the permeable barrier created by in situ redox manipulation. The precipitated uranium will W remobilized when the reductive capacity of the barrier is exhausted and the sediment is oxidized by the groundwater containing dissolved oxygen and other oxidants such as chromate. Although U(N) accumulates from years or decades of reduction/precipitation within the reduced zone, U(W) concentrations in solution are only somewhat elevated during aquifer oxidation because oxidation and dissolution reactions that release U(N) precipitate to solution are slow. The release rate of uranium into solution was found to be controlled mainly by the oxidation/dissolution rate of the U(IV) precipitate (half-life 200 hours) and partially by the fast oxidation of adsorbed Fe(II) (half- life 5 hours) and the slow oxidation of Fe(II)CO 3 (half-life 120 hours) in the reduced sediment. Simulations of uranium transport that incorporated these and other reactions under site-relevant conditions indicated that 35 ppb U(VI) is the maximum concentration likely to result from mobilization of the precipitated U(IV) species. Experiments also indicated that increasing the contact time between the U(IV) precipitates and the reduced sediment, which is likely to occur in the field, results in a slower U(IV) oxidation rate, which, in turn, would lower the maximum concentration of mobilized U(W). A six-month-long column experiment confirmed that

Understanding Uranium Behavior in a Reduced Aquifer

Science.gov (United States)

Janot, N.; Lezama-Pacheco, J. S.; Williams, K. H.; Bernier-Latmani, R.; Long, P. E.; Davis, J. A.; Fox, P. M.; Yang, L.; Giammar, D.; Cerrato, J. M.; Bargar, J.

2012-12-01

Uranium contamination of groundwater is a concern at several US Department of Energy sites, such Old Rifle, CO. Uranium transport in the environment is mainly controlled by its oxidation state, since oxidized U(VI) is relatively mobile, whereas U(IV) is relatively insoluble. Bio-remediation of contaminated aquifers aims at immobilizing uranium in a reduced form. Previous laboratory and field studies have shown that adding electron donor (lactate, acetate, ethanol) to groundwater stimulates the activity of metal- and sulfate-reducing bacteria, which promotes U(VI) reduction in contaminated aquifers. However, obtaining information on chemical and physical forms of U, Fe and S species for sediments biostimulated in the field, as well as kinetic parameters such as U(VI) reduction rate, is challenging due to the low concentration of uranium in the aquifers (typically bio-remediation experiment at the Old Rifle site, CO, from early iron-reducing conditions to the transition to sulfate-reducing conditions. Several in-well chromatographic columns packed with sediment were deployed and were sampled at different days after the start of bio-reduction. X-ray absorption spectroscopy and X-ray microscopy were used to obtain information on Fe, S and U speciation and distribution. Chemical extractions of the reduced sediments have also been performed, to determine the rate of Fe(II) and U(IV) accumulation.

Fast-track aquifer characterization and bioremediation of groundwater

International Nuclear Information System (INIS)

Owen, S.B.; Erskine, J.A.; Adkisson, C.

1995-01-01

A short duration step-drawdown pumping test has been used to characterize a highly permeable aquifer contaminated with petroleum hydrocarbons in support of an in situ, closed loop extraction and reinjection bioremediation system for groundwater. The short-term pumping test produces a manageable quantity of contaminated groundwater while yielding a range of values for transmissivity and specific yield parameters. This range of aquifer coefficients is used in an analytical model to estimate a range of groundwater extraction rates that provide a suitable radius of influence for the extraction and reinjection system. A multi-enzyme complex catalyzed bioremediation process has been used to aerobically degrade petroleum hydrocarbons. Enzymes, amino acids, and biosurfactants are supplied to the extracted groundwater to significantly speed up the degradation by naturally occurring bacteria. During the process, amino acids promote the rapid growth of the microbial population while enzymes and bacteria attach to hydrocarbons forming a transformation state complex that degrades to fatty acids, carbon dioxide, and water. This paper presents a case study of a fast-track bioremediation using pumping test data, analytical modeling, and an enzyme technology

Hanford Site 100-N Area In Situ Bioremediation of UPR-100-N-17, Deep Petroleum Unplanned Release - 13245

Energy Technology Data Exchange (ETDEWEB)

Saueressig, Daniel G. [Washington Closure Hanford, 2620 Fermi, Richland, Washington, 99354 (United States)

2013-07-01

In 1965 and 1966, approximately 303 m{sup 3} of Number 2 diesel fuel leaked from a pipeline used to support reactor operations at the Hanford Site's N Reactor. N Reactor was Hanford's longest operating reactor and served as the world's first dual purpose reactor for military and power production needs. The Interim Action Record of Decision for the 100-N Area identified in situ bioremediation as the preferred alternative to remediate the deep vadose zone contaminated by this release. A pilot project supplied oxygen into the vadose zone to stimulate microbial activity in the soil. The project monitored respiration rates as an indicator of active biodegradation. Based on pilot study results, a full-scale system is being constructed and installed to remediate the vadose zone contamination. (authors)

The use of bench- and field-scale data for design of an in situ carbon tetrachloride bioremediation system

International Nuclear Information System (INIS)

Peyton, B.M.; Truex, M.J.; Skeen, R.S.

1995-04-01

A suite of simulation models were developed as a design tool in support of an in situ bioremediation demonstration at the Hanford site in Washington state. The design tool, calibrated with field - and bench-scale data, was used to answer four field-scale system design questions: (1) What are the important reaction processes and kinetics? (2) How will biomass distribute in the aquifer in response to injected substrate? (3) What well configuration best ensures proper nutrient transport and process control? (4) What operating and monitoring strategy should be used to confirm effective remediation? This paper does not describe the design tool itself, but describes how the design tool was used to optimize field site design parameters such as well spacing, hydraulic control, contaminant destruction, and nutrient injection strategies

In-situ leaching of crownpoint, NM, uranium ore: Part 7 - Laboratory study of chemical agents for molybdenum restoration

International Nuclear Information System (INIS)

Strom, E.T.; Vogt, T.C.

1987-01-01

One possible drawback to the use of an in-situ leaching to recover uranium is the potential release of previously insoluble chemical species into the formation water. Before a pilot test of in-situ uranium leaching at Crownpoint, NM, was begun, extensive laboratory studies were undertaken to develop chemical methods for treating one possible contaminant, molybdenum (Mo). New Mexico regulations restrict the amount of Mo permissable in formation waters after leaching to less than 1 ppm. Two techniques to restore Mo after leaching were studied with core and pack tests. These studies suggest that if Mo restoration problems occur in the field, the use of precipitating agents such as Ca/sup 2+/ or reducing agents such as Fe/sup 2+/ may be helpful in ameliorating such problems

An analysis of prominent prospect of in-situ sandstone type uranium deposits in Yanji basins group, Jilin province

International Nuclear Information System (INIS)

Peng Zhidong; Zhang Shuyi

2003-01-01

In Mesozoic-Cenozoic era, many medium-small-sized sedimentary basins had been formed in Yanbian draped-faulted region of Jilin Province. The basement of these basins is constituted of U-riched granite body produced during late Hercynian-early Yanshan period. Uranium-mineralization has been found in coal-bearing formation, oil-bearing formation and in tint layer of red formation. On the bases of analyzing of uranium source, geologic tectonic, paleoclimatology, paleogeography, hydrogeology and reconstruction, it is concluded that there is a prominent prospect to discover large in-situ sandstone-type uranium deposits in Yanji basins. (authors)

In situ bioremediation of the saturated zone: It can be done

International Nuclear Information System (INIS)

Maher, A.; Kennel, N.D.; Jaworski, C.

1994-01-01

Bioremediation is being used to successfully reduce contaminant levels at a site located in central Iowa. At this site, indigenous microbial populations are being stimulated by the addition of nutrients and oxygen to degrade the contaminants of interest. The site is a former service station and an automobile repair facility. Gasoline and diesel fuel stored underground and/or dispensed through pumps leaked into the subsurface over a period of forty years. A site assessment revealed that significant adsorbed, dissolved, and phase separated contamination was present beneath the surface. A pump and treat system was installed in 1990 by others to treat the ground water contamination and achieve hydraulic control. Biotreatability studies indicated that bioremediation would be an effective remedial option for this site and in May 1992, the treatment system was retrofitted in order to expedite remediation. Microbial populations, ionic nutrient concentrations, physical, and contaminant data were evaluated over time to optimize treatment

BTEX AND MTBE BIOREMEDIATION: BIONETS™ CONTAINING SOS, PM1 AND ISOLITE®

Science.gov (United States)

MTBE and BTEX (benzene, toluene, ethylbenzene, and xylenes) are major problems of many sites in the United States. The objective of this study was to determine if biologically active in situ BioNets could bioremediate MTBE and BTEX contaminated groundwater. Seven BioNets w...

Bioremediation of soil and groundwater contaminated with stoddard solvent and mop oil using the PetroClean bioremediation system

International Nuclear Information System (INIS)

Schmitt, E.K.; Lieberman, M.T.; Caplan, J.A.; Blaes, D.; Keating, P.; Richards, W.

1991-01-01

This paper reports that Environmental Science and Engineering Inc. (ESE) was contracted by a confidential industrial client to perform a three-phased project. Phase I involved characterizing the site and delineating the extent of subsurface contamination. Phase II included biofeasibility and pilot-scale evaluations, determining remedial requirements, and designing the full-scale treatment system. Phase III involved implementing and operating the designed in situ bioremediation system (i.e., PetroClean 4000) to achieve site closure

Combining in situ chemical oxidation, stabilization, and anaerobic bioremediation in a single application to reduce contaminant mass and leachability in soil

Energy Technology Data Exchange (ETDEWEB)

Cassidy, Daniel P., E-mail: daniel.cassidy@wmich.edu [Department of Geosciences, Western Michigan University, Kalamazoo, MI 49008 (United States); Srivastava, Vipul J., E-mail: vipul.srivastava@ch2m.com [CH2M HILL, 125S Wacker, Ste 3000, Chicago, IL 60606 (United States); Dombrowski, Frank J., E-mail: frank.dombrowski@we-energies.com [We Energies, 333W Everett St., A231, Milwaukee, WI 53203 (United States); Lingle, James W., E-mail: jlingle@epri.com [Electric Power Research Institute (EPRI), 4927W Willow Road, Brown Deer, WI 53223 (United States)

2015-10-30

Highlights: • Portland cement and lime activated persulfate by increasing pH and temperature. • Chemical oxidation achieved BTEX and PAH removal ranging from 55% to 75%. • Activating persulfate with ISS amendments reduced leachability more than NaOH. • Native sulfate-reducing bacteria degraded PAHs within weeks after ISCO finished. • ISCO, ISS, and anaerobic bioremediation were combined in a single application. - Abstract: Laboratory batch reactors were maintained for 32 weeks to test the potential for an in situ remedy that combines chemical oxidation, stabilization, and anaerobic bioremediation in a single application to treat soil from a manufactured gas plant, contaminated with polycyclic aromatic hydrocarbons (PAH) and benzene, toluene, ethylbenzene, and xylenes (BTEX). Portland cement and slaked lime were used to activate the persulfate and to stabilize/encapsulate the contaminants that were not chemically oxidized. Native sulfate-reducing bacteria degraded residual contaminants using the sulfate left after persulfate activation. The ability of the combined remedy to reduce contaminant mass and leachability was compared with NaOH-activated persulfate, stabilization, and sulfate-reducing bioremediation as stand-alone technologies. The stabilization amendments increased pH and temperature sufficiently to activate the persulfate within 1 week. Activation with both stabilization amendments and NaOH removed between 55% and 70% of PAH and BTEX. However, combined persulfate and stabilization significantly reduced the leachability of residual BTEX and PAH compared with NaOH activation. Sulfide, 2-naphthoic acid, and the abundance of subunit A of the dissimilatory sulfite reductase gene (dsrA) were used to monitor native sulfate-reducing bacteria, which were negatively impacted by activated persulfate, but recovered completely within weeks.

Combining in situ chemical oxidation, stabilization, and anaerobic bioremediation in a single application to reduce contaminant mass and leachability in soil

International Nuclear Information System (INIS)

Cassidy, Daniel P.; Srivastava, Vipul J.; Dombrowski, Frank J.; Lingle, James W.

2015-01-01

Highlights: • Portland cement and lime activated persulfate by increasing pH and temperature. • Chemical oxidation achieved BTEX and PAH removal ranging from 55% to 75%. • Activating persulfate with ISS amendments reduced leachability more than NaOH. • Native sulfate-reducing bacteria degraded PAHs within weeks after ISCO finished. • ISCO, ISS, and anaerobic bioremediation were combined in a single application. - Abstract: Laboratory batch reactors were maintained for 32 weeks to test the potential for an in situ remedy that combines chemical oxidation, stabilization, and anaerobic bioremediation in a single application to treat soil from a manufactured gas plant, contaminated with polycyclic aromatic hydrocarbons (PAH) and benzene, toluene, ethylbenzene, and xylenes (BTEX). Portland cement and slaked lime were used to activate the persulfate and to stabilize/encapsulate the contaminants that were not chemically oxidized. Native sulfate-reducing bacteria degraded residual contaminants using the sulfate left after persulfate activation. The ability of the combined remedy to reduce contaminant mass and leachability was compared with NaOH-activated persulfate, stabilization, and sulfate-reducing bioremediation as stand-alone technologies. The stabilization amendments increased pH and temperature sufficiently to activate the persulfate within 1 week. Activation with both stabilization amendments and NaOH removed between 55% and 70% of PAH and BTEX. However, combined persulfate and stabilization significantly reduced the leachability of residual BTEX and PAH compared with NaOH activation. Sulfide, 2-naphthoic acid, and the abundance of subunit A of the dissimilatory sulfite reductase gene (dsrA) were used to monitor native sulfate-reducing bacteria, which were negatively impacted by activated persulfate, but recovered completely within weeks

On bacteria oxidizing enlargement scale test for uranium in-situ leaching at. 381 mine

International Nuclear Information System (INIS)

Hu Kaiguang; Wang Qingliang; Liu Yingjiu; Shi Wenge; Hu Shihe; Hu Yincai; Fang Qiu

1999-01-01

The results of enlarged scale test of bacteria as oxidizer for uranium in-situ leaching at No 381 mine showed that redox potential of the oxidized absorbed tailing water by bacteria is more than 510 mV, without any effects on after treatments by using bacteria as oxidizer and reduce oxidizer costs 70% compared with H 2 O 2 as oxidizer

In-situ grouting of uranium-mill-tailings piles: an assessment

International Nuclear Information System (INIS)

Tamura, T.; Boegly, W.J. Jr.

1983-05-01

Passage in 1978 of the Uranium Mill Tailings Radiation Control Act (UMTRCA) initiated a program of remedial action for 22 existing mill tailings piles generated in the period 1940 to 1970 as part of the nation's defense and nuclear power programs. The presence of these piles poses potential health and environmental contamination concerns. Possible remedial actions proposed include multilayer covers over the piles to reduce water infiltration, reduce radon gas releases, and reduce airborne transport of tailings fines. In addition, suggested remedial actions include (1) the use of liners to prevent groundwater contamination by leachates from the piles and (2) chemical stabilization of the tailings to retain the radioactive and nonradioactive sources of contamination. Lining of the piles would normally be applicable only to piles that are to be moved from their present location such that the liner could be placed between the tailings and the groundwater. However, by using civil engineering techniques developed for grouting rocks and soils for strength and water control, it may be possible to produce an in situ liner for piles that are not to be relocated. The Department of Energy (DOE) Uranium Mill Tailings Remedial Action Project Office requested that ORNL assess the potential application of grouting as a remedial action. This report examines the types of grouts, the equipment available, and the costs, and assesses the possibility of applying grouting technology as a remedial action alternative for uranium mill tailings piles

In-situ grouting of uranium-mill-tailings piles: an assessment

Energy Technology Data Exchange (ETDEWEB)

Tamura, T.; Boegly, W.J. Jr.

1983-05-01

Passage in 1978 of the Uranium Mill Tailings Radiation Control Act (UMTRCA) initiated a program of remedial action for 22 existing mill tailings piles generated in the period 1940 to 1970 as part of the nation's defense and nuclear power programs. The presence of these piles poses potential health and environmental contamination concerns. Possible remedial actions proposed include multilayer covers over the piles to reduce water infiltration, reduce radon gas releases, and reduce airborne transport of tailings fines. In addition, suggested remedial actions include (1) the use of liners to prevent groundwater contamination by leachates from the piles and (2) chemical stabilization of the tailings to retain the radioactive and nonradioactive sources of contamination. Lining of the piles would normally be applicable only to piles that are to be moved from their present location such that the liner could be placed between the tailings and the groundwater. However, by using civil engineering techniques developed for grouting rocks and soils for strength and water control, it may be possible to produce an in situ liner for piles that are not to be relocated. The Department of Energy (DOE) Uranium Mill Tailings Remedial Action Project Office requested that ORNL assess the potential application of grouting as a remedial action. This report examines the types of grouts, the equipment available, and the costs, and assesses the possibility of applying grouting technology as a remedial action alternative for uranium mill tailings piles.

Bioremediation of hydrocarbon polluted soil - Improvement of in situ bioremediation by bioaugmentation with endogenous and exogenous strains

OpenAIRE

Tarayre, Cédric

2010-01-01

Petroleum pollution has now become a real problem because hydrocarbons are persistent contaminants in soils and water. Contamination problems increase when ages of relevant facilities, such as oil storage tanks and pipelines, increase over time. The evolution of Legislation concerning soil pollution has led to the need of efficient techniques able to restore the polluted ground. Unfortunately, these techniques are expensive. Bioremediation of hydrocarbon polluted soils has been recognized as...

Trace Metal Bioremediation: Assessment of Model Components from Laboratory and Field Studies to Identify Critical Variables

International Nuclear Information System (INIS)

Peter Jaffe; Herschel Rabitz

2003-01-01

The objective of this project was to gain an insight into the modeling support needed for the understanding, design, and operation of trace metal/radionuclide bioremediation. To achieve this objective, a workshop was convened to discuss the elements such a model should contain. A ''protomodel'' was developed, based on the recommendations of the workshop, and was used to perform sensitivity analysis as well as some preliminary simulations in support for bioremediation test experiments at UMTRA sites. To simulate the numerous biogeochemical processes that will occur during the bioremediation of uranium contaminated aquifers, a time-dependent one-dimensional reactive transport model has been developed. The model consists of a set of coupled, steady state mass balance equations, accounting for advection, diffusion, dispersion, and a kinetic formulation of the transformations affecting an organic substrate, electron acceptors, corresponding reduced species, and uranium. This set of equations is solved numerically, using a finite element scheme. The redox conditions of the domain are characterized by estimating the pE, based on the concentrations of the dominant terminal electron acceptor and its corresponding reduced specie. This pE and the concentrations of relevant species are passed to a modified version of MINTEQA2, which calculates the speciation and solubilities of the species of interest. Kinetics of abiotic reactions are described as being proportional to the difference between the actual and equilibrium concentration. A global uncertainty assessment, determined by Random Sampling High Dimensional Model Representation (RS-HDMR), was performed to attain a phenomenological understanding of the origins of output variability and to suggest input parameter refinements as well as to provide guidance for field experiments to improve the quality of the model predictions. Results indicated that for the usually high nitrate contents found ate many DOE sites, overall

Combined use of flow cytometry and microscopy to study the interactions between the gram-negative betaproteobacterium Acidovorax facilis and uranium(VI)

Energy Technology Data Exchange (ETDEWEB)

Gerber, U., E-mail: u.gerber@hzdr.de [Helmholtz-Zentrum Dresden-Rossendorf, Institute of Resource Ecology, P.O. Box 510119, 01314 Dresden (Germany); Zirnstein, I. [Research Institute of Leather and Plastic Sheeting (FILK) gGmbH, Meissner Ring 1-5, 09599 Freiberg (Germany); Krawczyk-Bärsch, E. [Helmholtz-Zentrum Dresden-Rossendorf, Institute of Resource Ecology, P.O. Box 510119, 01314 Dresden (Germany); Lünsdorf, H. [Helmholtz Centre for Infection Research, Central Facility for Microscopy, Inhoffenstr. 7, D-38124 Braunschweig (Germany); Arnold, T. [Helmholtz-Zentrum Dresden-Rossendorf, Institute of Resource Ecology, P.O. Box 510119, 01314 Dresden (Germany); Merroun, M.L. [University of Granada, Department of Microbiology, Campus Fuentenueva, E-18071 Granada (Spain)

2016-11-05

Highlights: • Acidovorax facilis is able to remove 130 mg U/g dry biomass from solution. • Kinetically temperature-dependent uranium removal was studied. • Cell viability and metabolic activity was tested by flow cytometry. • Uranium was removed by active biosorption and passive bioaccumulation. - Abstract: The former uranium mine Königstein (Saxony, Germany) is currently in the process of remediation by means of controlled underground flooding. Nevertheless, the flooding water has to be cleaned up by a conventional wastewater treatment plant. In this study, the uranium(VI) removal and tolerance mechanisms of the gram-negative betaproteobacterium Acidovorax facilis were investigated by a multidisciplinary approach combining wet chemistry, flow cytometry, and microscopy. The kinetics of uranium removal and the corresponding mechanisms were investigated. The results showed a biphasic process of uranium removal characterized by a first phase where 95% of uranium was removed within the first 8 h followed by a second phase that reached equilibrium after 24 h. The bacterial cells displayed a total uranium removal capacity of 130 mg U/g dry biomass. The removal of uranium was also temperature-dependent, indicating that metabolic activity heavily influenced bacterial interactions with uranium. TEM analyses showed biosorption on the cell surface and intracellular accumulation of uranium. Uranium tolerance tests showed that A. facilis was able to withstand concentrations up to 0.1 mM. This work demonstrates that A. facilis is a suitable candidate for in situ bioremediation of flooding water in Königstein as well as for other contaminated waste waters.

In situ production of 36CI in uranium ore: a hydrogeological assessment tool

International Nuclear Information System (INIS)

Cornett, R.J.; Cramer, J.; Andrews, H.R.; Chant, L.A.; Davies, W.; Greiner, B.F.; Imahori, Y.; Koslowsky, V.; McKay, J.; Milton, G.M.; Milton, J.C.D.

1996-01-01

In situ neutron activation of 35 Cl within the rock and groundwater of geologic deposits that have elevated concentrations of uranium provides a hydrogeological tracer. We determine the production rate and mobility of 36 Cl in the 1.3-billion-year-old Cigar Lake uranium ore deposit. Accelerator mass spectrometry was used to map the Concentrations of 36 Cl in the ore and in the groundwater that were up to 100 times greater than those encountered in unmineralized portions of the host sandstone aquifer. The residence time of this mobile anion in groundwater within the mineralized zone ranged from 14 to 280 kyr. These residence times are consistent with the hydraulic and geochemical data, suggesting significant control of Cl - and groundwater movement by the clay-rich matrix of the mineralized zone. (author)

Combining in situ chemical oxidation, stabilization, and anaerobic bioremediation in a single application to reduce contaminant mass and leachability in soil.

Science.gov (United States)

Cassidy, Daniel P; Srivastava, Vipul J; Dombrowski, Frank J; Lingle, James W

2015-10-30

Laboratory batch reactors were maintained for 32 weeks to test the potential for an in situ remedy that combines chemical oxidation, stabilization, and anaerobic bioremediation in a single application to treat soil from a manufactured gas plant, contaminated with polycyclic aromatic hydrocarbons (PAH) and benzene, toluene, ethylbenzene, and xylenes (BTEX). Portland cement and slaked lime were used to activate the persulfate and to stabilize/encapsulate the contaminants that were not chemically oxidized. Native sulfate-reducing bacteria degraded residual contaminants using the sulfate left after persulfate activation. The ability of the combined remedy to reduce contaminant mass and leachability was compared with NaOH-activated persulfate, stabilization, and sulfate-reducing bioremediation as stand-alone technologies. The stabilization amendments increased pH and temperature sufficiently to activate the persulfate within 1 week. Activation with both stabilization amendments and NaOH removed between 55% and 70% of PAH and BTEX. However, combined persulfate and stabilization significantly reduced the leachability of residual BTEX and PAH compared with NaOH activation. Sulfide, 2-naphthoic acid, and the abundance of subunit A of the dissimilatory sulfite reductase gene (dsrA) were used to monitor native sulfate-reducing bacteria, which were negatively impacted by activated persulfate, but recovered completely within weeks. Copyright © 2015 Elsevier B.V. All rights reserved.

In situ leaching process for recording uranium values

International Nuclear Information System (INIS)

McKnight, W.M.; Timmins, T.H.; Sherry, H.S.

1977-01-01

A method of recovering uranium values from a subterranean deposit comprising: injecting an alkaline carbonate lixiviant into said deposit; flowing said alkaline carbonate lixiviant through said deposit to dissolve said uranium values into said lixiviant; producing said lixiviant and said dissolved uranium values from said deposit; flowing said lixiviant and said dissolved uranium values through an adsorption material to adsorp said uranium values from said lixiviant; eluting said adsorption material with an eluant of ammonium carbonate to desorb said uranium values from said adsorption material into said eluate in a concentration greater than in said lixiviant; heating said eluate and said desorbed uranium values to vaporize off ammonia and carbon dioxide therefrom, thereby causing uranium values to crystallize from the eluate; and recovering said solid uranium values

MICROBIAL ANALYSIS OF MTBE, BTEX BIOREMEDIATION: BIONETS CONTAINING PM1, SOS, ISOLITE.

Science.gov (United States)

MTBE and BTEX (benzene, toluene, ethylbenzene, and xylene) are major problems of many sites in the United States. The objective of this study was to determine if biologically active in-situ BioNets could bioremediation MTBE and BTEX contaminated groundwater. Seven BioNets were ...

MICROBIAL ANALYSIS OF MTBE, BTEX BIOREMEDIATION: BIONETS CONTAINING PM1, SOS, ISOLITE�

Science.gov (United States)

MTBE and BTEX (benzene, toluene, ethylbenzene, and xylene) are major problems of many sites in the United States. The objective of this study was to determine if biologically active in-situ BioNets could bioremediate MTBE and BTEX contaminated groundwater. Seven BioNets were plac...

Impact of organic carbon and nutrients mobilized during chemical oxidation on subsequent bioremediation of a diesel-contaminated soil

NARCIS (Netherlands)

Sutton, N.B.; Grotenhuis, J.T.C.; Rijnaarts, H.H.M.

2014-01-01

Remediation with in situ chemical oxidation (ISCO) impacts soil organic matter (SOM) and the microbial community, with deleterious effects on the latter being a major hurdle to coupling ISCO with in situ bioremediation (ISB). We investigate treatment of a diesel-contaminated soil with Fenton’s

A feasibility study on geological and hydrogeological setting or in-situ leaching mining in a sandstone-type uranium deposit

International Nuclear Information System (INIS)

Guo Sanmin.

1992-01-01

A comparative study is made of various conditions for in-situ leaching mining in a sandstone-type uranium deposit in Inner Mongolia with those of same types at home and abroad based on a large number of practical information. It is concluded that the deposit basically exhibits the geological conditions for in-situ leaching mining, and tentative plan and suggestion for further work are presented

Environmental impact assessment for uranium mine, mill and in situ leach projects

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-11-01

Environmental impact assessments and/or statements are an inherent part of any uranium mining project and are a prerequisite for the future opening of an exploitation and its final closure and decommissioning. Since they contain all information related to the physical, biological, chemical and economic condition of the areas where industrial projects are proposed or planned, they present invaluable guidance for the planning and implementation of environmental mitigation as well as environmental restoration after the mine is closed. They further yield relevant data on the socio-economic impacts of a project. The present report provides guidance on the environmental impact assessment of uranium mining and milling projects, including in situ leach projects which will be useful for companies in the process of planning uranium developments as well as for the regional or national authorities who will assess such developments. Additional information and advice is given through environmental case histories from five different countries. Those case histories are not meant to be prescriptions for conducting assessments nor even firm recommendations, but should serve as examples for the type and extent of work involved in assessments. A model assessment and licensing process is recommended based on the experience of the five countries. 1 fig., 5 tabs.

Environmental impact assessment for uranium mine, mill and in situ leach projects

International Nuclear Information System (INIS)

1997-11-01

Environmental impact assessments and/or statements are an inherent part of any uranium mining project and are a prerequisite for the future opening of an exploitation and its final closure and decommissioning. Since they contain all information related to the physical, biological, chemical and economic condition of the areas where industrial projects are proposed or planned, they present invaluable guidance for the planning and implementation of environmental mitigation as well as environmental restoration after the mine is closed. They further yield relevant data on the socio-economic impacts of a project. The present report provides guidance on the environmental impact assessment of uranium mining and milling projects, including in situ leach projects which will be useful for companies in the process of planning uranium developments as well as for the regional or national authorities who will assess such developments. Additional information and advice is given through environmental case histories from five different countries. Those case histories are not meant to be prescriptions for conducting assessments nor even firm recommendations, but should serve as examples for the type and extent of work involved in assessments. A model assessment and licensing process is recommended based on the experience of the five countries

The development and application of quantitative methods for the determination of in-situ radiometric uranium grade on the Witwatersrand gold and uranium mines

International Nuclear Information System (INIS)

Symons, G.

1985-12-01

A detailed investigation of background radiation levels near the reef zone in the uranium section of the Western Areas Mine was conducted using a collimated radiometric face scanner. This study demonstrated that these radiation levels can be high; 25% or more of the counts measured when sampling a reef face may originate from a background source, especially from uranium ore rubble on the footwall close to the reef face. A method using a 20mm frontal shield was devised to obtain an accurate background correction. Three calibration schemes, the Area method, the Gamlog method, and the Deconvolution method were implemented for the production of accurate in-situ radiometric uranium grades. This involved the construction of a step-response calibration pad at Pelindaba together with the establisment of appropriate software and underground radiometric sampling procedures. Radiometric grades generated by these calibration procedures from 60 channel sections were on average 10% below those procured from conventional chip sampling. A correlation between gold and uranium grades was also evident. Crushed rock samples were collected to investigate the thorium problem and are still undergoing analysis at the time of writing. Refinements in the design of the collimated face scanner are also described

Bioremediation: Effective treatment of petroleum-fuel-contaminated soil, a common environmental problem at industrial and governmental agency sites

International Nuclear Information System (INIS)

Jolley, R.L.; Donaldson, T.L.; Siegrist, R.L.; Walker, J.F.; MacNeill, J.J.; Ott, D.W.; Machanoff, R.A.; Adler, H.I.; Phelps, T.J.

1992-01-01

Bioremediation methods are receiving increased attention for degradation of petroleum-fuel-hydrocarbon contamination in soils. An in situ bioremediation demonstration is being conducted on petroleum-fuel-contaminated soil at Kwajalein Island, a remote Pacific site. Bioreaction parameters studied include water, air, nutrient, and microorganism culture addition. This paper presents planning and design aspects of the demonstration that is scheduled to be completed in 1993

A rapid in situ method for determining the ages of uranium oxide minerals: Evolution of the Cigar Lake deposit, Athabasca Basin

International Nuclear Information System (INIS)

Fayek, M.; Harrison, T.M.; Grove, M.; Coath, C.D.

2000-01-01

The authors present a rapid and accurate technique for making in situ U-Pb isotopic measurements of uranium oxide minerals that utilizes both electron and ion microprobes. U and Pb concentrations are determined using an electron microprobe, whereas the isotopic composition of Pb for the same area is measured using a high-resolution ion microprobe. The advantages of this approach are: mineral separation and chemical digestion are unnecessary; homogeneous uranium oxide standards, which are difficult to obtain, are not required; and precise and accurate U-Pb ages on ∼10 microm spots can be obtained in a matter of hours. The authors have applied their method to study the distribution of U-Pb ages in complexly intergrown uranium oxides from the unconformity-type Cigar Lake uranium deposit, Saskatchewan, Canada. In situ U-Pb results from early formed uraninite define a well-correlated array on concordia with upper and lower intercepts of 1,467 ± 63 Ma and 443 ± 96 Ma (±1σ), respectively. The 1,467 Ma age is interpreted as the minimum age of mineralization and is consistent with the age of clay-mineral alteration (approximately1477 Ma) and magnetization of diagenetic hematite (1,650 to 1,450 Ma) that is associated with these unconformity-type uranium deposits and early diagenesis of the Athabasca Basin sediments. In situ U-Pb isotopic analysis of uraninite and coffinite can document the Pb*/U heterogeneities that can occur on a scale of 15 to 30 microm, thus providing relatively accurate information regarding the timing of fluid interactions associated with the evolution of these deposits

Selection of lixiviants for in situ uranium leaching. Information circular

International Nuclear Information System (INIS)

Tweeton, D.R.; Peterson, K.A.

1981-10-01

This Bureau of Mines publication provides information to assist in selecting a lixiviant (leach solution) for in situ uranium leaching. The cost, advantages, and disadvantages of lixiviants currently used and proposed are presented. Laboratory and field tests are described, and applications of geochemical models are discussed. Environmental, economic, and technical factors should all be considered. Satisfying environmental regulations on restoring groundwater quality is becoming an overriding factor, favoring sodium bicarbonate or dissolved carbon dioxide over ammonium carbonate. The cheapest lixiviant is dissolved carbon dioxide, but it is not effective in all deposits. Technical factors include clay swelling by sodium, acid consumption by calcite, and the low solubility of oxygen in shallow deposits

Cometabolic bioremediation

Energy Technology Data Exchange (ETDEWEB)

Hazen, Terry C.

2009-02-15

Cometabolic bioremediation is probably the most under appreciated bioremediation strategy currently available. Cometabolism strategies stimulate only indigenous microbes with the ability to degrade the contaminant and cosubstrate e.g. methane, propane, toluene and others. This highly targeted stimulation insures that only those microbes that can degrade the contaminant are targeted, thus reducing amendment costs, well and formation plugging, etc. Cometabolic bioremediation has been used on some of the most recalcitrant contaminants, e.g. PCE, TCE, MTBE, TNT, dioxane, atrazine, etc. Methanotrophs have been demonstrated to produce methane monooxygense, an oxidase that can degrade over 300 compounds. Cometabolic bioremediation also has the advantage of being able to degrade contaminants to trace concentrations, since the biodegrader is not dependent on the contaminant for carbon or energy. Increasingly we are finding that in order to protect human health and the environment that we must remediate to lower and lower concentrations, especially for compounds like endocrine disrupters, thus cometabolism may be the best and maybe the only possibility that we have to bioremediate some contaminants.

In-Situ Air Sparaing: Engineering and Design

Science.gov (United States)

2008-01-31

removal (Adams and Reddy 2000). The potential for remediation of less volatile LNAPLs (e.g., diesel or fuel oils) is less promising, relying more on...pure nitrogen, or nitrous oxide) may enhance the speed at which bioremediation proceeds or alter the conditions under which it occurs. The USDOE Sa...region below the water table is directly related to in- situ bioremediation . IAS can be an alternative to other means of introducing oxygen into the

TECHNOLOGIES FOR BIOREMEDIATION OF SOILS CONTAMINATED WITH PETROLEUM PRODUCTS

OpenAIRE

Roxana Gabriela POPA

2012-01-01

Biological methods for remediation of soils is based on the degradation of pollutants due to activity of microorganisms (bacteria, fungi). Effectiveness of biological decontamination of soils depends on the following factors: biodegradation of pollutants, type of microorganisms used, choice of oxidant and nutrient and subject to clean up environmental characteristics. Ex situ techniques for bioremediation of soils polluted are: composting (static / mechanical agitation), land farming and biop...

In Situ Microbial Community Control of the Stability of Bio-reduced Uranium

International Nuclear Information System (INIS)

Baldwin, Brett R.; Peacock, Aaron D.; Resch, Charles T.; Arntzen, Evan; Smithgall, Amanda N.; Pfiffner, Susan; Gan, M.; McKinley, James P.; Long, Philip E.; White, David C.

2008-01-01

In aerobic aquifers typical of many Department of Energy (DOE) legacy waste sites, uranium is present in the oxidized U(VI) form which is more soluble and thus more mobile. Field experiments at the Old Rifle UMTRA site have demonstrated that biostimulation by electron donor addition (acetate) promotes biological U(VI) reduction (2). However, U(VI) reduction is reversible and oxidative dissolution of precipitated U(IV) after the cessation of electron donor addition remains a critical issue for the application of biostimulation as a treatment technology. Despite the potential for oxidative dissolution, field experiments at the Old Rifle site have shown that rapid reoxidation of bio-reduced uranium does not occur and U(VI) concentrations can remain at approximately 20% of background levels for more than one year. The extent of post-amendment U(VI) removal and the maintenance of bioreduced uranium may result from many factors including U(VI) sorption to iron-containing mineral phases, generation of H2S or FeS0.9, or the preferential sorption of U(VI) by microbial cells or biopolymers, but the processes controlling the reduction and in situ reoxidation rates are not known. To investigate the role of microbial community composition in the maintenance of bioreduced uranium, in-well sediment incubators (ISIs) were developed allowing field deployment of amended and native sediments during on-going experiments at the site. Field deployment of the ISIs allows expedient interrogation of microbial community response to field environmental perturbations and varying geochemical conditions.

In Situ Microbial Community Control of the Stability of Bio-reduced Uranium

Energy Technology Data Exchange (ETDEWEB)

Baldwin, Brett, R.; Peacock, Aaron, D.; Resch, Charles, T.; Arntzen, Evan; Smithgall, Amanda, N.; Pfiffner, Susan; Gan, M.; McKinley, James, P.; Long, Philip, E.; White, David, C.

2008-03-28

In aerobic aquifers typical of many Department of Energy (DOE) legacy waste sites, uranium is present in the oxidized U(VI) form which is more soluble and thus more mobile. Field experiments at the Old Rifle UMTRA site have demonstrated that biostimulation by electron donor addition (acetate) promotes biological U(VI) reduction (2). However, U(VI) reduction is reversible and oxidative dissolution of precipitated U(IV) after the cessation of electron donor addition remains a critical issue for the application of biostimulation as a treatment technology. Despite the potential for oxidative dissolution, field experiments at the Old Rifle site have shown that rapid reoxidation of bio-reduced uranium does not occur and U(VI) concentrations can remain at approximately 20% of background levels for more than one year. The extent of post-amendment U(VI) removal and the maintenance of bioreduced uranium may result from many factors including U(VI) sorption to iron-containing mineral phases, generation of H2S or FeS0.9, or the preferential sorption of U(VI) by microbial cells or biopolymers, but the processes controlling the reduction and in situ reoxidation rates are not known. To investigate the role of microbial community composition in the maintenance of bioreduced uranium, in-well sediment incubators (ISIs) were developed allowing field deployment of amended and native sediments during on-going experiments at the site. Field deployment of the ISIs allows expedient interrogation of microbial community response to field environmental perturbations and varying geochemical conditions.

Assessment of trace ground-water contaminants release from south Texas in-situ uranium solution-mining sites

Energy Technology Data Exchange (ETDEWEB)

Kidwell, J.R.; Humenick, M.J.

1981-01-01

The future of uranium solution mining in south Texas depends heavily on the industry's ability to restore production zone ground water to acceptable standards. This study investigated the extent of trace contaminant solubilization during mining and subsequent restoration attempts, first through a literature search centered on uranium control mechanisms, and then by laboratory experiments simulating the mining process. The literature search indicated the complexity of the situation. The number of possible interactions between indigenous elements and materials pointed on the site specificity of the problem. The column studies evaluated three different production area ores. Uranium, molybdenum, arsenic, vanadium, and selenium were analyzed in column effluents. After simulated mining operations were completed, uranium was found to be the most persistent trace element. However, subsequent ground water flushing of the columns could restore in-situ water to EPA recommended drinking water concentrations. Limited data indicated that ground water flowing through mined areas may solubilize molybdenum present in down gradient areas adjacent to the production zone due to increased oxidation potential of ground water if adequate restoration procedures are not followed.

The theory and method of two-well field test for in-situ leaching uranium

International Nuclear Information System (INIS)

Yao Yixuan; Huo Jiandang; Xiang Qiulin; Tang Baobin

2007-01-01

Because leaching area in field test for in-situ leaching uranium is not accounted exactly, the reliability of obtaining parameters by calculating can not be ensured, and the whole test needs a long time and great investment. In two-well field test, lixiviant is injected from one well, pregnant solution is pumped out from the other, flow rate of the production well is more than that of the injection well, and uranium is not recoveried. In the case of keeping invariable ratio of pumping capacity to injecting capacity during the testing process, leaching area is not variable, can be exactly calculated. The full field test needs six months to one year. Two-well test is a scientific, rapid, minimal spending field test method, and is widely used in Commonwealth of Independent States. (authors)

Bioremediation of chlorinated solvents and diesel soils

International Nuclear Information System (INIS)

Huismann, S.S.; Peterson, M.A.; Jardine, R.J.

1995-01-01

The US Army, in a cooperative effort with the Tennessee Valley Authority (TVA) and its cooperator, ENSR, performed an innovative enhanced bioremediation project at Fort Gillem in Atlanta, Georgia. The objective of the project was to remediate six hundred cubic yards of soil affected by a mixture of chlorinated compounds and petroleum hydrocarbons which posed a threat to uppermost groundwater and private drinking water wells. ENSR completed a demonstration project to measure the effects of bioremediation on both chlorinated compounds (primarily TCE) and petroleum hydrocarbons (number-sign 2 diesel). Contaminated soil was placed on top of a bermed polyethylene liner to construct an ex-situ biovault. Nutrients were added to the soil as it was loaded onto the liner. Contaminated soil was also used to construct a control vault. A methane barrier cover was placed over both piles. The cover was designed to prevent short circuiting of induced airflow in and around the enhanced pile, and to prevent the release of fugitive emissions from either pile

Influence of a precepitator on bioremedial processes

Directory of Open Access Journals (Sweden)

Nježić Zvonko B.

2010-01-01

Full Text Available Natural environment represents a dynamic bioreactor with numerous chemical, biochemical and microbiological processes through which harmful materials are destroyed, so that living organisms and human beings are not endanger. Controlled anthropogenic actions can assist the natural ecosystem to become an efficient bioremedial unit and to reduce the level of effluents produced in the biotechnological transformations during massive food production. In this study, a monitoring system for the chemical oxygen demand (COD and the heavy metal levels in water was established, followed by construction and building of a precipitator in order to prevent discharging of sludge. The results contribute to the hypothesis of existence of in situ bioremedial processes in the observed ecosystem. The significant influence of the precipitator on the decrease of pollution was demonstrated: a decrease of both the COD value and the heavy metal levels downstream from the precipitator for about 15%. Therefore it can be concluded that the precipitator significantly contributes to the ecosystem by the reduction of pollutant level.

A review on slurry bioreactors for bioremediation of soils and sediments

Directory of Open Access Journals (Sweden)

Poggi-Varaldo Héctor M

2008-02-01

Full Text Available Abstract The aim of this work is to present a critical review on slurry bioreactors (SB and their application to bioremediation of soils and sediments polluted with recalcitrant and toxic compounds. The scope of the review encompasses the following subjects: (i process fundamentals of SB and analysis of advantages and disadvantages; (ii the most recent applications of SB to laboratory scale and commercial scale soil bioremediation, with a focus on pesticides, explosives, polynuclear aromatic hydrocarbons, and chlorinated organic pollutants; (iii trends on the use of surfactants to improve availability of contaminants and supplementation with degradable carbon sources to enhance cometabolism of pollutants; (iv recent findings on the utilization of electron acceptors other than oxygen; (v bioaugmentation and advances made on characterization of microbial communities of SB; (vi developments on ecotoxicity assays aimed at evaluating bioremediation efficiency of the process. From this review it can be concluded that SB is an effective ad situ and ex situ technology that can be used for bioremediation of problematic sites, such as those characterized by soils with high contents of clay and organic matter, by pollutants that are recalcitrant, toxic, and display hysteretic behavior, or when bioremediation should be accomplished in short times under the pressure and monitoring of environmental agencies and regulators. SB technology allows for the convenient manipulation and control of several environmental parameters that could lead to enhanced and faster treatment of polluted soils: nutrient N, P and organic carbon source (biostimulation, inocula (bioaugmentation, increased availability of pollutants by use of surfactants or inducing biosurfactant production inside the SB, etc. An interesting emerging area is the use of SB with simultaneous electron acceptors, which has demonstrated its usefulness for the bioremediation of soils polluted with

A review on slurry bioreactors for bioremediation of soils and sediments.

Science.gov (United States)

Robles-González, Ireri V; Fava, Fabio; Poggi-Varaldo, Héctor M

2008-02-29

The aim of this work is to present a critical review on slurry bioreactors (SB) and their application to bioremediation of soils and sediments polluted with recalcitrant and toxic compounds. The scope of the review encompasses the following subjects: (i) process fundamentals of SB and analysis of advantages and disadvantages; (ii) the most recent applications of SB to laboratory scale and commercial scale soil bioremediation, with a focus on pesticides, explosives, polynuclear aromatic hydrocarbons, and chlorinated organic pollutants; (iii) trends on the use of surfactants to improve availability of contaminants and supplementation with degradable carbon sources to enhance cometabolism of pollutants; (iv) recent findings on the utilization of electron acceptors other than oxygen; (v) bioaugmentation and advances made on characterization of microbial communities of SB; (vi) developments on ecotoxicity assays aimed at evaluating bioremediation efficiency of the process.From this review it can be concluded that SB is an effective ad situ and ex situ technology that can be used for bioremediation of problematic sites, such as those characterized by soils with high contents of clay and organic matter, by pollutants that are recalcitrant, toxic, and display hysteretic behavior, or when bioremediation should be accomplished in short times under the pressure and monitoring of environmental agencies and regulators. SB technology allows for the convenient manipulation and control of several environmental parameters that could lead to enhanced and faster treatment of polluted soils: nutrient N, P and organic carbon source (biostimulation), inocula (bioaugmentation), increased availability of pollutants by use of surfactants or inducing biosurfactant production inside the SB, etc. An interesting emerging area is the use of SB with simultaneous electron acceptors, which has demonstrated its usefulness for the bioremediation of soils polluted with hydrocarbons and some

Mapping of depleted uranium with in situ spectrometry and soil samples

International Nuclear Information System (INIS)

Shebell, P.; Reginatto, M.; Monetti, M.; Faller, S.; Davis, L.

1999-01-01

Depleted uranium (DU) has been developed in the past two decades as a highly effective material for armor penetrating rounds and vehicle shielding. There is now a growing interest in the defense community to determine the presence and extent of DU contamination quickly and with a minimum amount of intrusive sampling. We report on a new approach using deconvolution techniques to quantitatively map DU contamination in surface soil. This approach combines data from soil samples with data from in situ gamma-ray spectrometry measurements to produce an accurate and detailed map of DU contamination. Results of a field survey at the Aberdeen Proving Ground are presented. (author)

Geochemical data from groundwater at the proposed Dewey Burdock uranium in-situ recovery mine, Edgemont, South Dakota

Science.gov (United States)

Johnson, Raymond H.

2012-01-01

This report releases groundwater geochemistry data from samples that were collected in June 2011 at the Dewey Burdock proposed uranium in-situ recovery site near Edgemont, South Dakota. The sampling and analytical methods are summarized, and all of the data, including quality assurance/quality control information are provided in data tables.

Effectiveness of bioremediation for the Prestige fuel spill : a summary of case studies

Energy Technology Data Exchange (ETDEWEB)

Gallego, J.R. [Oviedo Univ., Asturias (Spain); Gonzalez-Rojas, E.; Pelaez, A.I.; Sanchez, J [Oviedo Univ., Asturias (Spain). Inst. de Biotecnologia de Asturias; Garcia-Martinez, M.J.; Llamas, J.F. [Univ. Polictenica de Madrid, Madrid (Spain). Laboratorio de Estratigrafia Biomolecular

2006-07-01

This paper described novel bioremediation strategies used to remediate coastal areas in Spain impacted by the Prestige fuel oil spill in 2002. The bioremediation techniques were applied after hot pressurized water washing was used to remove hydrocarbons adhering to shorelines and rocks. Bioremediation strategies included monitored natural attenuation as well as accelerating biodegradation by stimulating indigenous populations through the addition of exogenous microbial populations. The sites selected for bioremediation were rocky shorelines of heterogenous granitic sediments with grain sizes ranging from sands to huge boulders; limestone-sandstone pebbles and cobbles; and fuel-coated limestone cliffs. Total surface area covered by the fuel was determined through the use of image analysis calculations. A statistical measurement of the fuel layer thickness was calculated by averaging the weights of multiple-fuel sampling increments. Bioremediation products included the use of oleophilic fertilizers; a biodegradable surfactant; and a microbial seeding agent. Determinations of saturate, aromatic, resins, and asphaltene (SARA) were performed using maltenes extraction and liquid chromatography. Microbial plating and selective enrichment with fuel as the sole carbon source were used to monitor the evolution of microbial populations in a variety of experiments. It was concluded that the biostimulation technique enhanced the efficiency of the in situ oleophilic fertilizers. 17 refs., 2 tabs., 6 figs.

Effectiveness of bioremediation for the Prestige fuel spill : a summary of case studies

International Nuclear Information System (INIS)

Gallego, J.R.; Gonzalez-Rojas, E.; Pelaez, A.I.; Sanchez, J; Garcia-Martinez, M.J.; Llamas, J.F.

2006-01-01

This paper described novel bioremediation strategies used to remediate coastal areas in Spain impacted by the Prestige fuel oil spill in 2002. The bioremediation techniques were applied after hot pressurized water washing was used to remove hydrocarbons adhering to shorelines and rocks. Bioremediation strategies included monitored natural attenuation as well as accelerating biodegradation by stimulating indigenous populations through the addition of exogenous microbial populations. The sites selected for bioremediation were rocky shorelines of heterogenous granitic sediments with grain sizes ranging from sands to huge boulders; limestone-sandstone pebbles and cobbles; and fuel-coated limestone cliffs. Total surface area covered by the fuel was determined through the use of image analysis calculations. A statistical measurement of the fuel layer thickness was calculated by averaging the weights of multiple-fuel sampling increments. Bioremediation products included the use of oleophilic fertilizers; a biodegradable surfactant; and a microbial seeding agent. Determinations of saturate, aromatic, resins, and asphaltene (SARA) were performed using maltenes extraction and liquid chromatography. Microbial plating and selective enrichment with fuel as the sole carbon source were used to monitor the evolution of microbial populations in a variety of experiments. It was concluded that the biostimulation technique enhanced the efficiency of the in situ oleophilic fertilizers. 17 refs., 2 tabs., 6 figs

Microbial decontamination of uranium mine drainage

International Nuclear Information System (INIS)

Hard, B.C.; Babel, W.

2001-01-01

One of the problems one is faced with when uranium mines are closed is the decontamination of acid mine drainage (AMD) from tailings and flooding of the underground mines. The high concentrations of sulfates and metals in mining water make it impossible to dispose of the water into rivers without having to decontaminate it first. A bioremediation process is proposed in which sulfate-reducing bacteria are used to remove metals, neutralize the water and reduce the sulfate concentrations. Methylotrophic sulfate-reducing strains have been isolated which can be used in such a process. Lab scale experiments with different reactor types were carried out in order to find the optimum design for this bioremediation process. Comparisons were made between methanol and other electron donors with regards to their suitability as substrate for this process. Methanol was found to be most suited. Laboratory data suggest that immobilizing the bacteria on pumice particles increases the sulfate-reduction rate (SRR) up to three fold to 18 mg/l.h, compared to the rates of free flowing cells of between 3.7 and 6.8 mg/l.h. Preliminary experiments on a larger scale (15 l) using acid mine drainage pH 2.5 show SRR of 0.71 mg/l.h. In biosorption experiments up to 140 mg of aluminium per g biomass was removed from the water. One strain was found to reduce uranium VI, thus changing it from the soluble to the insoluble form. The application of the proposed process with regards to bioremediation of AMD are discussed. (orig.)

Bicarbonate leaching of uranium

International Nuclear Information System (INIS)

Mason, C.

1998-01-01

The alkaline leach process for extracting uranium from uranium ores is reviewed. This process is dependent on the chemistry of uranium and so is independent on the type of mining system (conventional, heap or in-situ) used. Particular reference is made to the geochemical conditions at Crownpoint. Some supporting data from studies using alkaline leach for remediation of uranium-contaminated sites is presented

Bicarbonate leaching of uranium

Energy Technology Data Exchange (ETDEWEB)

Mason, C.

1998-12-31

The alkaline leach process for extracting uranium from uranium ores is reviewed. This process is dependent on the chemistry of uranium and so is independent on the type of mining system (conventional, heap or in-situ) used. Particular reference is made to the geochemical conditions at Crownpoint. Some supporting data from studies using alkaline leach for remediation of uranium-contaminated sites is presented.

Bacterial Community Succession During in situ Uranium Bioremediation: Spatial Similarities Along Controlled Flow Paths

International Nuclear Information System (INIS)

Hwang, Chiachi; Wu, Weimin; Gentry, Terry J.; Carley, Jack; Corbin, Gail A.; Carroll, Sue L.; Watson, David B.; Jardine, Phil M.; Zhou, Jizhong; Criddle, Craig S.; Fields, Matthew W.

2009-01-01

Bacterial community succession was investigated in a field-scale subsurface reactor formed by a series of wells that received weekly ethanol additions to re-circulating groundwater. Ethanol additions stimulated denitrification, metal reduction, sulfate reduction, and U(VI) reduction to sparingly soluble U(IV). Clone libraries of SSU rRNA gene sequences from groundwater samples enabled tracking of spatial and temporal changes over a 1.5 y period. Analyses showed that the communities changed in a manner consistent with geochemical variations that occurred along temporal and spatial scales. Canonical correspondence analysis revealed that the levels of nitrate, uranium, sulfide, sulfate, and ethanol strongly correlated with particular bacterial populations. As sulfate and U(VI) levels declined, sequences representative of sulfate-reducers and metal-reducers were detected at high levels. Ultimately, sequences associated with sulfate-reducing populations predominated, and sulfate levels declined as U(VI) remained at low levels. When engineering controls were compared to the population variation via canonical ordination, changes could be related to dissolved oxygen control and ethanol addition. The data also indicated that the indigenous populations responded differently to stimulation for bio-reduction; however, the two bio-stimulated communities became more similar after different transitions in an idiosyncratic manner. The strong associations between particular environmental variables and certain populations provide insight into the establishment of practical and successful remediation strategies in radionuclide-contaminated environments with respect to engineering controls and microbial ecology.

Bacterial Community Succession During in situ Uranium Bioremediation: Spatial Similarities Along Controlled Flow Paths

Energy Technology Data Exchange (ETDEWEB)

Hwang, Chiachi; Wu, Weimin; Gentry, Terry J.; Carley, Jack; Corbin, Gail A.; Carroll, Sue L.; Watson, David B.; Jardine, Phil M.; Zhou, Jizhong; Criddle, Craig S.; Fields, Matthew W.

2009-05-22

Bacterial community succession was investigated in a field-scale subsurface reactor formed by a series of wells that received weekly ethanol additions to re-circulating groundwater. Ethanol additions stimulated denitrification, metal reduction, sulfate reduction, and U(VI) reduction to sparingly soluble U(IV). Clone libraries of SSU rRNA gene sequences from groundwater samples enabled tracking of spatial and temporal changes over a 1.5 y period. Analyses showed that the communities changed in a manner consistent with geochemical variations that occurred along temporal and spatial scales. Canonical correspondence analysis revealed that the levels of nitrate, uranium, sulfide, sulfate, and ethanol strongly correlated with particular bacterial populations. As sulfate and U(VI) levels declined, sequences representative of sulfate-reducers and metal-reducers were detected at high levels. Ultimately, sequences associated with sulfate-reducing populations predominated, and sulfate levels declined as U(VI) remained at low levels. When engineering controls were compared to the population variation via canonical ordination, changes could be related to dissolved oxygen control and ethanol addition. The data also indicated that the indigenous populations responded differently to stimulation for bio-reduction; however, the two bio-stimulated communities became more similar after different transitions in an idiosyncratic manner. The strong associations between particular environmental variables and certain populations provide insight into the establishment of practical and successful remediation strategies in radionuclide-contaminated environments with respect to engineering controls and microbial ecology.

Experimental study and numerical modelling of geochemical reactions occurring during uranium in situ recovery (ISR) mining

International Nuclear Information System (INIS)

Ben Simon, R.

2011-09-01

The in situ Recovery (ISR) method consists of ore mining by in situ chemical leaching with acid or alkaline solutions. ISR takes place underground and is therefore limited to the analysis of the pumped solutions, hence ISR mine management is still empirical. Numerical modelling has been considered to achieve more efficient management of this process. Three different phenomena have to be taken into account for numerical simulations of uranium ISR mining: (1) geochemical reactions; (2) the kinetics of these reactions, and (3) hydrodynamic transport with respect to the reaction kinetics. Leaching tests have been conducted on ore samples from an uranium mine in Tortkuduk (Kazakhstan) where ISR is conducted by acid leaching. Two types of leaching experiments were performed: (1) tests in batch reactors; and (2) extraction in flow through columns. The assumptions deduced from the leaching tests were tested and validated by modelling the laboratory experiments with the numerical codes CHESS and HYTEC, both developed at the Geosciences research center of Mines ParisTech. A well-constrained 1D hydrogeochemical transport model of the ISR process at laboratory-scale was proposed. It enables to translate the chemical release sequence that is observed during experiments into a geochemical reaction sequence. It was possible to highlight the controlling factors of uranium dissolution, and the precipitation of secondary mineral phase in the deposit, as well as the determination of the relative importance of these factors. (author)

Persistent U(IV) and U(VI) following in-situ recovery (ISR) mining of a sandstone uranium deposit, Wyoming, USA

Science.gov (United States)

Gallegos, Tanya J.; Campbell, Kate M.; Zielinski, Robert A.; Reimus, P.W.; J.T. Clay,; N. Janot,; J. J. Bargar,; Benzel, William M.

2015-01-01

Drill-core samples from a sandstone-hosted uranium (U) deposit in Wyoming were characterized to determine the abundance and distribution of uranium following in-situ recovery (ISR) mining with oxygen- and carbon dioxide-enriched water. Concentrations of uranium, collected from ten depth intervals, ranged from 5 to 1920 ppm. A composite sample contained 750 ppm uranium with an average oxidation state of 54% U(VI) and 46% U(IV). Scanning electron microscopy (SEM) indicated rare high uranium (∼1000 ppm U) in spatial association with P/Ca and Si/O attributed to relict uranium minerals, possibly coffinite, uraninite, and autunite, trapped within low permeability layers bypassed during ISR mining. Fission track analysis revealed lower but still elevated concentrations of U in the clay/silica matrix and organic matter (several 10 s ppm) and yet higher concentrations associated with Fe-rich/S-poor sites, likely iron oxides, on altered chlorite or euhedral pyrite surfaces (but not on framboidal pyrite). Organic C (mining, the likely sequestration of uranium within labile iron oxides following mining and sensitivity to changes in redox conditions requires careful attention during groundwater restoration.

Bioremediation of soil and water: application to chemical and nuclear pollutions

International Nuclear Information System (INIS)

Vavasseur, Alain

2014-06-01

Bioremediation is a branch of biotechnology that uses natural or diverted biological mechanisms to address environmental problems. The biological agents can be simple organic molecules, such as DNA or antibodies, or live or dead organisms (bacteria, microalgae, fungi, higher algae and plants). Phyto-remediation refers more specifically to using plants to decontaminate polluted soil, water, or air. Unlike organic pollutants such as PCBs1, TNT2, TCE3, which can be metabolized by soil microorganisms and plant roots, radionuclides - like most heavy metals - cannot be degraded. Thus, bioremediation strategies for radionuclides will consist into: - stabilization/mineralization to reduce their bioavailability through a change in their redox state; - for soil, their extraction using the plant nutrition mechanisms; - for polluted solutions, their extraction using the 'cation traps' properties of plant cell walls. Compared to physicochemical methods conventionally used to decontaminate soils but which lead to a sharp decline in fertility and productivity, bioremediation is considered a friendly environmental technology. An important advantage of this technique is its cost, much lower than traditional remediation techniques. By cons, bioremediation cannot be applied in an emergency, because processing times are spread over several years - even decades - depending on the degree of pollution. Therefore current research focuses on optimizing the processing time. We present in this paper several examples of in situ bioremediation of heavy metals and radionuclides, and we discuss in conclusion the negative and positive aspects of this technique. (author)

Degradability of n-alkanes during ex situ natural bioremediation of soil contaminated by heavy residual fuel oil (mazut

Directory of Open Access Journals (Sweden)

Ali Ramadan Mohamed Muftah

2013-01-01

Full Text Available It is well known that during biodegradation of oil in natural geological conditions, or oil pollutants in the environment, a degradation of hydrocarbons occurs according to the well defined sequence. For example, the major changes during the degradation process of n-alkanes occur in the second, slight and third, moderate level (on the biodegradation scale from 1 to 10. According to previous research, in the fourth, heavy level, when intensive changes of phenanthrene and its methyl isomers begin, n-alkanes have already been completely removed. In this paper, the ex situ natural bioremediation (unstimulated bioremediation, without addition of biomass, nutrient substances and biosurfactant of soil contaminated with heavy residual fuel oil (mazut was conducted during the period of 6 months. Low abundance of n-alkanes in the fraction of total saturated hydrocarbons in the initial sample (identification was possible only after concentration by urea adduction technique showed that the investigated oil pollutant was at the boundary between the third and the fourth biodegradation level. During the experiment, an intense degradation of phenanthrene and its methyl-, dimethyl-and trimethyl-isomers was not followed by the removal of the remaining n-alkanes. The abundance of n-alkanes remained at the initial low level, even at end of the experiment when the pollutant reached one of the highest biodegradation levels. These results showed that the unstimulated biodegradation of some hydrocarbons, despite of their high biodegradability, do not proceed completely to the end, even at final degradation stages. In the condition of the reduced availability of some hydrocarbons, microorganisms tend to opt for less biodegradable but more accessible hydrocarbons.

In-situ uranium leaching

International Nuclear Information System (INIS)

Dotson, B.J.

1986-01-01

This invention provides a method for improving the recovery of mineral values from ore bodies subjected to in-situ leaching by controlling the flow behaviour of the leaching solution. In particular, the invention relates to an in-situ leaching operation employing a foam for mobility control of the leaching solution. A foam bank is either introduced into the ore bed or developed in-situ in the ore bed. The foam then becomes a diverting agent forcing the leaching fluid through the previously non-contacted regions of the deposit

Investigation of disposal of nitrate-bearing effluent from in-situ leaching process by natural evaporation in Yining uranium mine

International Nuclear Information System (INIS)

Huang Chongyuan; Li Weicai; Zhang Yutai; Gao Xizhen

2000-01-01

Experiments indicated, after lime neutralization and precipitation of nitrate-bearing effluent from in-situ leaching process, uranium concentration increase with the increasing of nitrate concentration. Only when nitrate concentration is <0.5 mg/L, uranium concentration can drop from 1.5-2.0 mg/L to about 1.0 mg/L. The permeability coefficient of soil is about 1.0-1.1 m/d in the place which is scheduled for building natural evaporation pool. After lime neutralization of nitrate-bearing effluent, it can drop to 0.03-0.01 m/d. Setting up water-proof layer in natural evaporation pool can reduce pollution of underground water by uranium, nitrate and ammonium

Experience with restoration of ore-bearing aquifers after in situ leach uranium mining

International Nuclear Information System (INIS)

Yazikov, V.G.; Zabaznov, V.U.

2002-01-01

In many cases the most important environmental issue for in situ leach uranium mining technology is the impact on groundwater. Usually the greatest issue is the chemical condition of the ore bearing aquifer following the completion of leaching. Based on experience gained during post leach monitoring, it has been found that in properly selected sites the impact following leaching is greatly reduced because of the process of self restoration, otherwise known as natural attenuation. This paper provides ground water monitoring data from 1985 to 1997 following completion of leaching at the Irkol uranium deposit, Kazakhstan. It shows the evolution of the pH, and other chemical parameters over this period. The monitoring results demonstrate that at this site the process of natural attenuation appears to have effectively reduced the impact on groundwater at the site, as well as to keep contaminated leaching fluids from moving more than a few hundreds of metres from the wellfield. (author)

Biodegradation and bioremediation

DEFF Research Database (Denmark)

Albrechtsen, H.-J.

1996-01-01

Anmeldelse af Alexander,M.: Biodegradation and bioremediation. Academic Press, Sandiego, USA, 1994......Anmeldelse af Alexander,M.: Biodegradation and bioremediation. Academic Press, Sandiego, USA, 1994...

MICROBIAL ANALYSIS OF MTBE, BTEX BIOREMEDIATION: BIONETS(TM) CONTAINING PM1, SOS, ISOLITE (R)

Science.gov (United States)

MTBE and BTEX (benzene, toluene, ethylbenzene, and xylene) are major problems of many sites in the United States. The objective of this study was to determine if biologically active in-situ BioNets could bioremediation MTBE and BTEX contaminated groundwater. Seven BioNets were ...

Impact of organic carbon and nutrients mobilized during chemical oxidation on subsequent bioremediation of a diesel-contaminated soil.

Science.gov (United States)

Sutton, Nora B; Grotenhuis, Tim; Rijnaarts, Huub H M

2014-02-01

Remediation with in situ chemical oxidation (ISCO) impacts soil organic matter (SOM) and the microbial community, with deleterious effects on the latter being a major hurdle to coupling ISCO with in situ bioremediation (ISB). We investigate treatment of a diesel-contaminated soil with Fenton's reagent and modified Fenton's reagent coupled with a subsequent bioremediation phase of 187d, both with and without nutrient amendment. Chemical oxidation mobilized SOM into the liquid phase, producing dissolved organic carbon (DOC) concentrations 8-16 times higher than the untreated field sample. Higher aqueous concentrations of nitrogen and phosphorous species were also observed following oxidation; NH4(+) increased 14-172 times. During the bioremediation phase, dissolved carbon and nutrient species were utilized for microbial growth-yielding DOC concentrations similar to field sample levels within 56d of incubation. In the absence of nutrient amendment, the highest microbial respiration rates were correlated with higher availability of nitrogen and phosphorus species mobilized by oxidation. Significant diesel degradation was only observed following nutrient amendment, implying that nutrients mobilized by chemical oxidation can increase microbial activity but are insufficient for bioremediation. While all bioremediation occurred in the first 28d of incubation in the biotic control microcosm with nutrient amendment, biodegradation continued throughout 187d of incubation following chemical oxidation, suggesting that chemical treatment also affects the desorption of organic contaminants from SOM. Overall, results indicate that biodegradation of DOC, as an alternative substrate to diesel, and biological utilization of mobilized nutrients have implications for the success of coupled ISCO and ISB treatments. Copyright © 2013 Elsevier Ltd. All rights reserved.

Development of the integrated in situ Lasagna process

International Nuclear Information System (INIS)

Ho, S.; Athmer, C.; Sheridan, P.

1995-01-01

Contamination in deep, low permeability soils poses a significant technical challenge to in-situ remediation efforts. Poor accessibility to the contaminants and difficulty in uniform delivery of treatment reagents have rendered existing in-situ methods such as bioremediation, vapor extraction, and pump and treat rather ineffective when applied to low permeability soils present at many contaminated sites

Uranium 2000 : International symposium on the process metallurgy of uranium

International Nuclear Information System (INIS)

Ozberk, E.; Oliver, A.J.

2000-01-01

The International Symposium on the Process Metallurgy of Uranium has been organized as the thirtieth annual meeting of the Hydrometallurgy Section of the Metallurgical Society of the Canadian Institute of Mining, Metallurgy and Petroleum (CIM). This meeting is jointly organized with the Canadian Mineral Processors Division of CIM. The proceedings are a collection of papers from fifteen countries covering the latest research, development, industrial practices and regulatory issues in uranium processing, providing a concise description of the state of this industry. Topics include: uranium industry overview; current milling operations; in-situ uranium mines and processing plants; uranium recovery and further processing; uranium leaching; uranium operations effluent water treatment; tailings disposal, water treatment and decommissioning; mine decommissioning; and international regulations and decommissioning. (author)

Literature review and assessment of various approaches to bioremediation of oil and associated hydrocarbons in soil and groundwater

International Nuclear Information System (INIS)

1993-08-01

A study was conducted of available techniques for the biological treatment of oil and associated hydrocarbon contamination in soil and groundwater. The study involved a detailed literature search and review, as well as discussions with the users and developers of a number of the bioremediation techniques assessed. The result is a compendium of selected state-of-the-art bioremediation technologies which can serve to guide the selection process for treatment technology for a particular site subject to remediation. Background is provided on the various classes of sites on which petroleum-related contamination could occur, and the nature of contaminants typical of such sites. The mechanisms of hydrocarbon biodegradation are outlined along with various approaches to bioremediation such as in-situ, on-site, bioreactors, landfarming, composting, and physical/chemical treatments. Field trials required to characterize the site and provide an indication of the suitability of bioremediation and the most appropriate bioremediation approach are described. Commercially available bioremediation technologies are briefly discussed. A number of the bioremedial techniques reviewed are compared to more conventional treatment processes in terms of such criteria as operating cost, effectiveness, advantages, risks, applicability, equipment and manpower requirements, and considerations regarding usage in Canadian conditions. 15 figs., 17 tabs

Literature review and assessment of various approaches to bioremediation of oil and associated hydrocarbons in soil and groundwater

Energy Technology Data Exchange (ETDEWEB)

1993-08-01

A study was conducted of available techniques for the biological treatment of oil and associated hydrocarbon contamination in soil and groundwater. The study involved a detailed literature search and review, as well as discussions with the users and developers of a number of the bioremediation techniques assessed. The result is a compendium of selected state-of-the-art bioremediation technologies which can serve to guide the selection process for treatment technology for a particular site subject to remediation. Background is provided on the various classes of sites on which petroleum-related contamination could occur, and the nature of contaminants typical of such sites. The mechanisms of hydrocarbon biodegradation are outlined along with various approaches to bioremediation such as in-situ, on-site, bioreactors, landfarming, composting, and physical/chemical treatments. Field trials required to characterize the site and provide an indication of the suitability of bioremediation and the most appropriate bioremediation approach are described. Commercially available bioremediation technologies are briefly discussed. A number of the bioremedial techniques reviewed are compared to more conventional treatment processes in terms of such criteria as operating cost, effectiveness, advantages, risks, applicability, equipment and manpower requirements, and considerations regarding usage in Canadian conditions. 15 figs., 17 tabs.

The Influence of Soil Chemical Factors on In Situ Bioremediation of Soil Contamination

Energy Technology Data Exchange (ETDEWEB)

Breedveld, Gijs D.

1997-12-31

Mineral oil is the major energy source in Western society. Production, transport and distribution of oil and oil products cause serious contamination problems of water, air and soil. The present thesis studies the natural biodegradation processes in the soil environment which can remove contamination by oil products and creosote. The main physical/chemical processes determining the distribution of organic contaminants between the soil solid, aqueous and vapour phase are discussed. Then a short introduction to soil microbiology and environmental factors important for biodegradation is given. There is a discussion of engineered and natural bioremediation methods and the problems related to scaling up laboratory experiments to field scale remediation. Bioremediation will seldom remove the contaminants completely; a residue remains. Factors affecting the level of residual contamination and the consequences for contaminant availability are discussed. Finally, the main findings of the work are summarized and recommendations for further research are given. 111 refs., 41 figs., 19 tabs.

Electron transport chains in organohalide-respiring bacteria and bioremediation implications.

Science.gov (United States)

Wang, Shanquan; Qiu, Lan; Liu, Xiaowei; Xu, Guofang; Siegert, Michael; Lu, Qihong; Juneau, Philippe; Yu, Ling; Liang, Dawei; He, Zhili; Qiu, Rongliang

2018-04-06

In situ remediation employing organohalide-respiring bacteria represents a promising solution for cleanup of persistent organohalide pollutants. The organohalide-respiring bacteria conserve energy by utilizing H 2 or organic compounds as electron donors and organohalides as electron acceptors. Reductive dehalogenase (RDase), a terminal reductase of the electron transport chain in organohalide-respiring bacteria, is the key enzyme that catalyzes halogen removal. Accumulating experimental evidence thus far suggests that there are distinct models for respiratory electron transfer in organohalide-respirers of different lineages, e.g., Dehalococcoides, Dehalobacter, Desulfitobacterium and Sulfurospirillum. In this review, to connect the knowledge in organohalide-respiratory electron transport chains to bioremediation applications, we first comprehensively review molecular components and their organization, together with energetics of the organohalide-respiratory electron transport chains, as well as recent elucidation of intramolecular electron shuttling and halogen elimination mechanisms of RDases. We then highlight the implications of organohalide-respiratory electron transport chains in stimulated bioremediation. In addition, major challenges and further developments toward understanding the organohalide-respiratory electron transport chains and their bioremediation applications are identified and discussed. Copyright © 2018 Elsevier Inc. All rights reserved.

Engineered in situ bioremediation of a petroleum hydrocarbon-contaminated aquifer: assessment of mineralization based on alkalinity, inorganic carbon and stable carbon isotope balances

Science.gov (United States)

Hunkeler, Daniel; Höhener, Patrick; Bernasconi, Stefano; Zeyer, Josef

1999-04-01

A concept is proposed to assess in situ petroleum hydrocarbon mineralization by combining data on oxidant consumption, production of reduced species, CH 4, alkalinity and dissolved inorganic carbon (DIC) with measurements of stable isotope ratios. The concept was applied to a diesel fuel contaminated aquifer in Menziken, Switzerland, which was treated by engineered in situ bioremediation. In the contaminated aquifer, added oxidants (O 2 and NO 3-) were consumed, elevated concentrations of Fe(II), Mn(II), CH 4, alkalinity and DIC were detected and the DIC was generally depleted in 13C compared to the background. The DIC production was larger than expected based on the consumption of dissolved oxidants and the production of reduced species. Stable carbon isotope balances revealed that the DIC production in the aquifer originated mainly from microbial petroleum hydrocarbon mineralization, and that geochemical reactions such as carbonate dissolution produced little DIC. This suggests that petroleum hydrocarbon mineralization can be underestimated if it is determined based on concentrations of dissolved oxidants and reduced species.

Research and transference of the ICES over Malargue, Mendoza, uranium bioremediation

International Nuclear Information System (INIS)

Scotti, A.; Barbero, N.; Castano-Ganan, A.R; Ramires, A.; Ojeda, C.; Meza, Juan C.; Lopez, S.; Salgan, Laura; Diaz Isenrath, G.

2009-01-01

The origin of the International Center for Earth Sciences (ICES) dates back to 2002 when the Acoustic Emission Station on Volcano Peteroa was installed. Up to now, it represents the first of its kind in the entire Andean Cordillera. This scientific activity is jointly coordinated by scientists from Italy and Argentina. At the First Conference on Acoustic Emission held on 2004, a letter of intent for the establishment of ICES was signed. Presently, ICES is composed by 4 departments: Environment and Climate; Anthropology; Environmental and Territorial Environmental Risk; Resources and Exploration Geophysics. One of the primary objectives of ICES is to promoting applied research and development in the broad field of Earth Sciences. The experimental work consists of main 4 steps listed below: The 'Helianthus annus' (sunflower) has proven its ability to raise Uranium (U) in hydroponic systems and was widely used in the model U rizophyiltration extraction of groundwater in Ashtabula, Ohio, USA. Hydroponic trial design consists of 6 treatments and 4 repetitions plants witnesses without minimum level of U, U witnesses plants without and 4 with various levels of U (Stage 1). The Glomus intraradices is a mycorrhizal fungus used in strategies of U phyto-stabilization. Test consists in the cultivation of sunflower with roots inoculated with Glomus intraradices to determine their uptake and translocation of U (Stage 2). The inoculation of 'Glomus intraradices' in 'Helianthus annus' produces an effective symbiosis with the type of strain and its genetic diversity, some genotypes are highly suitable for this. There have been experiences of this kind in the basic research in several countries. In this work, we use the system in 'Helianthus-Glomus' phyto-stabilization or rizophyiltration soil as a strategy for bioremediation of U at the Malargue area, Province of Mendoza (Stage 3). It will launch a pilot test of the transfer plan, which involves creating a garden for the growth of

Remote-sensing and geological information for prospective area selection of in-situ leachable sandstone-type uranium deposit in Songliao and Liaohe faulted-depressed basins

International Nuclear Information System (INIS)

Yu Baoshan

1998-01-01

On the basis of remote-sensing information and geological environments for the formation of in-situ leachable sandstone-type uranium deposits such as geomorphic features, distribution of drainage system, and paleo-alluvial (diluvial) fans and time-space distribution regularities of orehosting rocks and sandstone bodies in Songliao and Liaohe faulted-depressed basins, image features, tectonic patterns and paleo-geographic environment of the prospective areas are discussed for both basins, and based on a great number of petroleum-geological data and comparison analysis, a remote sensing-geological prospecting model for in-situ leachable sandstonetype uranium deposits in the region is established, providing indications for selection of prospective area

Network succession reveals the importance of competition in response to emulsified vegetable oil amendment for uranium bioremediation.

Science.gov (United States)

Deng, Ye; Zhang, Ping; Qin, Yujia; Tu, Qichao; Yang, Yunfeng; He, Zhili; Schadt, Christopher Warren; Zhou, Jizhong

2016-01-01

Discerning network interactions among different species/populations in microbial communities has evoked substantial interests in recent years, but little information is available about temporal dynamics of microbial network interactions in response to environmental perturbations. Here, we modified the random matrix theory-based network approach to discern network succession in groundwater microbial communities in response to emulsified vegetable oil (EVO) amendment for uranium bioremediation. Groundwater microbial communities from one control and seven monitor wells were analysed with a functional gene array (GeoChip 3.0), and functional molecular ecological networks (fMENs) at different time points were reconstructed. Our results showed that the network interactions were dramatically altered by EVO amendment. Dynamic and resilient succession was evident: fairly simple at the initial stage (Day 0), increasingly complex at the middle period (Days 4, 17, 31), most complex at Day 80, and then decreasingly complex at a later stage (140-269 days). Unlike previous studies in other habitats, negative interactions predominated in a time-series fMEN, suggesting strong competition among different microbial species in the groundwater systems after EVO injection. Particularly, several keystone sulfate-reducing bacteria showed strong negative interactions with their network neighbours. These results provide mechanistic understanding of the decreased phylogenetic diversity during environmental perturbations. © 2015 Society for Applied Microbiology and John Wiley & Sons Ltd.

Restoration of groundwater quality after in situ uranium leaching. Open file report (final) October 1977-August 1979

International Nuclear Information System (INIS)

Riding, J.R.; Rosswog, F.J.

1979-08-01

In situ solution mining of uranium has several environmental advantages over other mining techniques. The leaching of uranium, however, alters the ground water in the aquifer where the leaching occurs. A requirement of the mining technique is the control of objectionable materials that are introduced into the water. This report reviews the state of the art in restoring ground water quality. Current restoration practices discussed include disposal wells and solar evaporation ponds. Sweeping techniques by producing water flow from all wells during restoration and recirculating techniques by recharging water from a surface purification plant are evaluated. Methods for predicting the effectiveness and costs of current methods are presented. Possible alternatives for restoration of the ground water quality are described

In situ bioremediation of petroleum hydrocarbons and chlorinated hydrocarbons: Three case studies

International Nuclear Information System (INIS)

Bost, R.C.; Perry, R.G.; Barber, T.

1997-01-01

In situ biodegradation of organic contaminants is one of the most cost-effective means of site remediation. This method has proven successful in soils, ground water, and slurries. Bacteria capable of degrading organic contaminants within an aquifer include many species from a wide spectrum of genera, e.g. Pseudomonas, Corynebacterium, Bacillus, etc. In most cases, a mixture of bacterial strains is required to completely oxidize a complex organic contaminant. Each strain of an organism may target a specific compound, working together with other organisms to ultimately degrade each intermediate until complete degradation, also known as mineralization, occurs. One or more of the following mechanisms are utilized by bacteria for organic chemical degradation: (1) aerobic, (2) anaerobic, and (3) co-metabolic. During aerobic oxidation of organic chemicals, bacteria utilize the pollutant as an electron and hydrogen source and oxygen acts as the electron and hydrogen acceptor, resulting in water. As the bacterial enzymes cleave the compound, oxidized products are produced along with energy for the reaction to proceed. This is the most rapid and widely utilized mechanism. Dehalogenation occurs under aerobic, or perhaps more often, under anoxic conditions. This process occurs in the presence of alternate electron acceptors and replaces chlorine with hydrogen. The mechanism of co-metabolism can be aerobic or anaerobic, but is more often aerobic. This process requires a separate energy source for the bacterial cell because the pollutant is not utilized as an energy source. The role of bioremediation in site remediation is demonstrated below by three case studies: (1) a refinery, (2) a municipal landfill and (3) a pesticide formulation plant

Solid-phase data from cores at the proposed Dewey Burdock uranium in-situ recovery mine, near Edgemont, South Dakota

Science.gov (United States)

Johnson, Raymond H.; Diehl, Sharon F.; Benzel, William M.

2013-01-01

This report releases solid-phase data from cores at the proposed Dewey Burdock uranium in-situ recovery site near Edgemont, South Dakota. These cores were collected by Powertech Uranium Corporation, and material not used for their analyses were given to the U.S. Geological Survey for additional sampling and analyses. These additional analyses included total carbon and sulfur, whole rock acid digestion for major and trace elements, 234U/238U activity ratios, X-ray diffraction, thin sections, scanning electron microscopy analyses, and cathodoluminescence. This report provides the methods and data results from these analyses along with a short summary of observations.

Bio-chemical remediation of under-ground water contaminated by uranium in-situ leaching

International Nuclear Information System (INIS)

Wang Qingliang; Li Qian; Zhang Hongcan; Hu Eming; Chen Yongbo

2014-01-01

In the process of uranium in-situ leaching, it was serious that strong acid, uranium and heavy metals, and SO_4"2"-, NO_3"- could contaminate underground water. To remedy these pollutants, conventional methods are high-cost and low-efficient, so a bio-chemical remediation method was proposed to cope with the under-ground water pollution in this study. The results showed, in the chemical treatment with Ca(OH)_2 neutralization, pH went up from 2.0 to 7.0, the removal rates of U, Mn"2"+, Zn"2"+, Pb"2"+, SO_4"2"-, NO_3"- were 91.5%, 78.3%, 85.1%, 100%, 71.4% and 2.6% respectively, SO_4"2"- and NO_3"- need to be treated again by bio-method. In the biological process, the Hydraulic Retention Time (HRT) of bioreactor was controlled at 42 h, and 100% NO_3"- and 70% SO_4"2"- in the contaminated water were removed; Acidithiobacillus ferrooxidans (A. f) liquid to H_2S showed better absorption effect, can fully meet the process requirements of H_2S removal. (authors)

Theoretical stability assessment of uranyl phosphates and apatites: Selection of amendments for in situ remediation of uranium

International Nuclear Information System (INIS)

Raicevic, S.; Wright, J.V.; Veljkovic, V.; Conca, J.L.

2006-01-01

Addition of an amendment or reagent to soil/sediment is a technique that can decrease mobility and reduce bioavailability of uranium (U) and other heavy metals in the contaminated site. According to data from literature and results obtained in field studies, the general mineral class of apatites was selected as a most promising amendment for in situ immobilization/remediation of U. In this work we presented theoretical assessment of stability of U(VI) in four apatite systems (hydroxyapatite (HAP), North Carolina Apatite (NCA), Lisina Apatite (LA), and Apatite II) in order to determine an optimal apatite soil amendment which could be used for in situ remediation of uranium. In this analysis we used a theoretical criterion which is based on calculation of the ion-ion interaction potential, representing the main term of the cohesive energy of the matrix/pollutant system. The presented results of this analysis indicate (i) that the mechanism of immobilization of U by natural apatites depends on their chemical composition and (ii) that all analyzed apatites represent, from the point of view of stability, promising materials which could be used in field remediation of U-contaminated sites

In Situ Bioreduction of Uranium (VI) to Submicromolar Levels and Reoxidation by Dissolved Oxygen

International Nuclear Information System (INIS)

Wu, Weimin; Carley, Jack M.; Luo, Jian; Ginder-Vogel, Matthew A.; Cardenas, Erick; Leigh, Mary Beth; Hwang, Chaichi; Kelly, Shelly D.; Ruan, Chuanmin; Wu, Liyou; Van Nostrand, Joy; Gentry, Terry J.; Lowe, Kenneth Alan; Mehlhorn, Tonia L.; Carroll, Sue L.; Luo, Wensui; Fields, Matthew Wayne; Gu, Baohua; Watson, David B.; Kemner, Kenneth M.; Marsh, Terence; Tiedje, James; Zhou, Jizhong; Fendorf, Scott; Kitanidis, Peter K.; Jardine, Philip M.; Criddle, Craig

2007-01-01

Groundwater within Area 3 of the U.S. Department of Energy (DOE) Environmental Remediation Sciences Program (ERSP) Field Research Center at Oak Ridge, TN (ORFRC) contains up to 135 (micro)M uranium as U(VI). Through a series of experiments at a pilot scale test facility, we explored the lower limits of groundwater U(VI) that can be achieved by in-situ biostimulation and the effects of dissolved oxygen on immobilized uranium. Weekly 2 day additions of ethanol over a 2-year period stimulated growth of denitrifying, Fe(III)-reducing, and sulfate-reducing bacteria, and immobilization of uranium as U(IV), with dissolved uranium concentrations decreasing to low levels. Following sulfite addition to remove dissolved oxygen, aqueous U(VI) concentrations fell below the U.S. Environmental Protection Agency maximum contaminant limit (MCL) for drinking water ( -1 or 0.126 (micro)M). Under anaerobic conditions, these low concentrations were stable, even in the absence of added ethanol. However, when sulfite additions stopped, and dissolved oxygen (4.0-5.5 mg L -1 ) entered the injection well, spatially variable changes in aqueous U(VI) occurred over a 60 day period, with concentrations increasing rapidly from <0.13 to 2.0 (micro)M at a multilevel sampling (MLS) well located close to the injection well, but changing little at an MLS well located further away. Resumption of ethanol addition restored reduction of Fe(III), sulfate, and U(VI) within 36 h. After 2 years of ethanol addition, X-ray absorption near-edge structure spectroscopy (XANES) analyses indicated that U(IV) comprised 60-80% of the total uranium in sediment samples. At the completion of the project (day 1260), U concentrations in MLS wells were less than 0.1 (micro)M. The microbial community at MLS wells with low U(VI) contained bacteria that are known to reduce uranium, including Desulfovibrio spp. and Geobacter spp., in both sediment and groundwater. The dominant Fe(III)-reducing species were Geothrix spp

Large Scale Bioremediation of Petroleum Hydrocarbon Contaminated Waste at Various Installations of ONGC. India: Case Studies

OpenAIRE

Mandal, Ajoy Kumar; Sarma, Priyangshu Manab; Jeyaseelan, C Paul; Channashettar, Veeranna A; Singh, Bina; Agnihotri, Anil; Lal, Banwari; Datta, Jayati

2014-01-01

In situ and ex situ bioremediation of oil contaminated effluent pits, sludge pits, oil spilled land and tank bottom, and effluent treatment plant (ETP) oily sludge was carried out at Ankleshwar, Mehsana, Assam and Cauvery Asset of Oil and Natural Gas Corporation Limited (ONGC), India. The types of contaminant were heavy paraffinic, asphaltic and light crude oil and emulsified oily sludge /contaminated soil. An indigenous microbial consortium was developed by assembling four species of bacteri...

Biostimulation of indigenous microbial community for bioremediation of petroleum refinery sludge.

Directory of Open Access Journals (Sweden)

Jayeeta Sarkar

2016-09-01

Full Text Available Nutrient deficiency severely impairs the catabolic activity of indigenous microorganisms in hydrocarbon rich environments (HREs and limits the rate of intrinsic bioremediation. The present study aimed to characterize the microbial community in refinery waste and evaluate the scope for biostimulation based in situ bioremediation. Samples recovered from the wastewater lagoon of Guwahati refinery revealed a hydrocarbon enriched high total petroleum hydrocarbon (TPH, oxygen-, moisture-limited, reducing environment. Intrinsic biodegradation ability of the indigenous microorganisms was enhanced significantly (>80% reduction in TPH by 90 days with nitrate amendment. Preferred utilization of both higher- (>C30 and middle- chain (C20-30 length hydrocarbons were evident from GC-MS analysis. Denaturing gradient gel electrophoresis (DGGE and community level physiological profiling (CLPP analyses indicated distinct shift in community’s composition and metabolic abilities following nitrogen (N amendment. High throughput deep sequencing of 16S rRNA gene showed that the native community was mainly composed of hydrocarbon degrading, syntrophic, methanogenic, nitrate/iron/sulfur reducing facultative anaerobic bacteria and archaebacteria, affiliated to γ- and δ-Proteobacteria and Euryarchaeota respectively. Genes for aerobic and anaerobic alkane metabolism (alkB and bssA, methanogenesis (mcrA, denitrification (nirS and narG and N2 fixation (nifH were detected. Concomitant to hydrocarbon degradation, lowering of dissolve O2 and increase in oxidation-reduction potential (ORP marked with an enrichment of N2 fixing, nitrate reducing aerobic/facultative anaerobic members e.g., Azovibrio, Pseudoxanthomonas and Commamonadaceae members was evident in N amended microcosm. This study highlighted that indigenous community of refinery sludge was intrinsically diverse, yet appreciable rate of in situ bioremediation could be achieved by supplying adequate N sources.

Biostimulation of Indigenous Microbial Community for Bioremediation of Petroleum Refinery Sludge

Science.gov (United States)

Sarkar, Jayeeta; Kazy, Sufia K.; Gupta, Abhishek; Dutta, Avishek; Mohapatra, Balaram; Roy, Ajoy; Bera, Paramita; Mitra, Adinpunya; Sar, Pinaki

2016-01-01

Nutrient deficiency severely impairs the catabolic activity of indigenous microorganisms in hydrocarbon rich environments (HREs) and limits the rate of intrinsic bioremediation. The present study aimed to characterize the microbial community in refinery waste and evaluate the scope for biostimulation based in situ bioremediation. Samples recovered from the wastewater lagoon of Guwahati refinery revealed a hydrocarbon enriched [high total petroleum hydrocarbon (TPH)], oxygen-, moisture-limited, reducing environment. Intrinsic biodegradation ability of the indigenous microorganisms was enhanced significantly (>80% reduction in TPH by 90 days) with nitrate amendment. Preferred utilization of both higher- (>C30) and middle- chain (C20-30) length hydrocarbons were evident from GC-MS analysis. Denaturing gradient gel electrophoresis and community level physiological profiling analyses indicated distinct shift in community’s composition and metabolic abilities following nitrogen (N) amendment. High throughput deep sequencing of 16S rRNA gene showed that the native community was mainly composed of hydrocarbon degrading, syntrophic, methanogenic, nitrate/iron/sulfur reducing facultative anaerobic bacteria and archaebacteria, affiliated to γ- and δ-Proteobacteria and Euryarchaeota respectively. Genes for aerobic and anaerobic alkane metabolism (alkB and bssA), methanogenesis (mcrA), denitrification (nirS and narG) and N2 fixation (nifH) were detected. Concomitant to hydrocarbon degradation, lowering of dissolve O2 and increase in oxidation-reduction potential (ORP) marked with an enrichment of N2 fixing, nitrate reducing aerobic/facultative anaerobic members [e.g., Azovibrio, Pseudoxanthomonas and Comamonadaceae members] was evident in N amended microcosm. This study highlighted that indigenous community of refinery sludge was intrinsically diverse, yet appreciable rate of in situ bioremediation could be achieved by supplying adequate N sources. PMID:27708623

Final Project Report, DE-SC0001280, Characterizing the Combined Roles of Iron and Transverse Mixing on Uranium Bioremediation in Groundwater using Microfluidic Devices

Energy Technology Data Exchange (ETDEWEB)

Finneran, Kevin [Clemson Univ., SC (United States); Werth, Charles [Univ. of Texas, Austin, TX (United States); Strathmann, Timothy [Univ. of Illinois, Urbana-Champaign, IL (United States)

2015-01-10

In situ bioremediation of U(VI) involves amending groundwater with an appropriate electron donor and limiting nutrients to promote biological reduction to the less soluble and mobile U(IV) oxidation state. Groundwater flow is laminar; mixing is controlled by hydrodynamic dispersion. Recent studies indicate that transverse dispersion along plume margins can limit mixing of the amended electron donor and accepter (such as U(VI) in remediation applications). As a result, microbial growth, and subsequently contaminant reaction, may be limited to these transverse mixing zones during bioremediation. The primary objective of this work was to characterize the combined effects of hydrology, geochemistry, and biology on the (bio)remediation of U(VI). Our underlying hypothesis was that U(VI) reaction in groundwater is controlled by transverse mixing with an electron donor along plume margins, and that iron bioavailability in these zones affects U(VI) reduction kinetics and U(IV) re-oxidation. Our specific objectives were to a) quantify reaction kinetics mediated by biological versus geochemical reactions leading to U(VI) reduction and U(IV) re-oxidation, b) understand the influence of bioavailable iron on U(VI) reduction and U(IV) re-oxidation along the transverse mixing zones, c) determine how transverse mixing limitations and the presence of biomass in pores affects these reactions, and d) identify how microbial populations that develop along transverse mixing zones are influenced by the presence of iron and the concentration of electron donor. In the completed work, transverse mixing zones along plume margins were re-created in microfluidic pore networks, referred to as micromodels. We conducted a series of experiments that allowed us to distinguish among the hydraulic, biological, and geochemical mechanisms that contribute to U(VI) reduction, U(IV) re-oxidation, and U(VI) abiotic reaction with the limiting biological nutrient HP042-. This systematic approach may lead to a

Risk-based approach for bioremediation of fuel hydrocarbons at a major airport

International Nuclear Information System (INIS)

Wiedemeier, T.H.; Guest, P.R.; Blicker, B.R.

1994-01-01

This paper describes a risk-based approach for bioremediation of fuel-hydrocarbon-contaminated soil and ground water at a major airport in Colorado. In situ bioremediation pilot testing, natural attenuation modeling, and full-scale remedial action planning and implementation for soil and ground water contamination has conducted at four airport fuel farms. The sources of fuel contamination were leaking underground storage tanks (USTs) or pipelines transporting Jet A fuel and aviation gasoline. Continuing sources of contamination were present in several small cells of free-phase product and in fuel residuals trapped within the capillary fringe at depths 15 to 20 feet below ground surface. Bioventing pilot tests were conducted to assess the feasibility of using this technology to remediate contaminated soils. The pilot tests included measurement of initial soil gas chemistry at the site, determination of subsurface permeability, and in situ respiration tests to determine fuel biodegradation rates. A product recovery test was also conducted. ES designed and installed four full-scale bioventing systems to remediate the long-term sources of continuing fuel contamination. Benzene, toluene, ethylbenzene, and xylenes (BTEX) and total petroleum hydrocarbons (TPH) were detected in ground water at concentrations slightly above regulatory guidelines

An enhanced aerobic bioremediation system at a central production facility -- system design and data analysis

International Nuclear Information System (INIS)

Chiang, C.; Petkovsky, P.; Beltz, M.; Rouse, S.; Boyd, T.; Newell, C.; McHugh, T.

1993-01-01

A successful field demonstration of the enhanced in-situ aerobic bioremediation with remarkable results took place during the period of August 1, 1991 through year-end 1992 at a central production facility in Michigan. The in-situ soil logging and groundwater sampling by the cone penetrometer/porous probe system provided a real-time definition of the groundwater flow ''channel'' and a clear delineation of the plume extent. That facilitated the design of the closed-loop bioremediation system, consisting of two downgradient pumping wells to completely capture the plume and two pairs of bi-level injection wells located upgradient of the plume. The purged groundwater from the two pumping wells after amending with dissolved oxygen is directly reinjected to the two pairs of upgradient bi-level injection wells. In addition, the performance of the system is monitored by 17 multilevel piezometers. Each piezometer consists of four vertical sampling levels, providing a total of 68 sampling points to fully define the three-dimensional characteristics of the BTEX and DO plumes. Based on a hydrograph analysis of the groundwater data, the closed-loop bioremediation system has been operating properly. In addition, a particle tracking analysis showed groundwater flowlines converge to the pumping wells demonstrating the effectiveness of the plume capture. The trend analysis showed a consistent decline of BTEX concentrations at all of the 68 sampling points

Bioprecipitation of uranium from alkaline waste solutions using recombinant Deinococcus radiodurans

Energy Technology Data Exchange (ETDEWEB)

Kulkarni, Sayali; Ballal, Anand; Apte, Shree Kumar, E-mail: aptesk@barc.gov.in

2013-11-15

Highlights: • Deinococcus radiodurans was genetically engineered to overexpress alkaline phosphatase (PhoK). • Deino-PhoK bioprecipitated U efficiently over a wide range of input U concentration. • A maximal loading of 10.7 g U/g of biomass at 10 mM input U was observed. • Radioresistance and U precipitation by Deino-PhoK remained unaffected by γ radiation. • Immobilization of Deino-PhoK facilitated easy separation of precipitated U. -- Abstract: Bioremediation of uranium (U) from alkaline waste solutions remains inadequately explored. We engineered the phoK gene (encoding a novel alkaline phosphatase, PhoK) from Sphingomonas sp. for overexpression in the radioresistant bacterium Deinococcus radiodurans. The recombinant strain thus obtained (Deino-PhoK) exhibited remarkably high alkaline phosphatase activity as evidenced by zymographic and enzyme activity assays. Deino-PhoK cells could efficiently precipitate uranium over a wide range of input U concentrations. At low uranyl concentrations (1 mM), the strain precipitated >90% of uranium within 2 h while a high loading capacity of around 10.7 g U/g of dry weight of cells was achieved at 10 mM U concentration. Uranium bioprecipitation by Deino-PhoK cells was not affected in the presence of Cs and Sr, commonly present in intermediate and low level liquid radioactive waste, or after exposure to very high doses of ionizing radiation. Transmission electron micrographs revealed the extracellular nature of bioprecipitated U, while X-ray diffraction and fluorescence analysis identified the precipitated uranyl phosphate species as chernikovite. When immobilized into calcium alginate beads, Deino-PhoK cells efficiently removed uranium, which remained trapped in beads, thus accomplishing physical separation of precipitated uranyl phosphate from solutions. The data demonstrate superior ability of Deino-PhoK, over earlier reported strains, in removal of uranium from alkaline solutions and its potential use in

Uranium oxidation kinetics monitored by in-situ X-ray diffraction

Energy Technology Data Exchange (ETDEWEB)

Zalkind, S., E-mail: shimonzl@nrcn.org.il; Rafailov, G.; Halevy, I.; Livneh, T.; Rubin, A.; Maimon, H.; Schweke, D.

2017-03-15

The oxidation kinetics of U-0.1 wt%Cr at oxygen pressures of 150 Torr and the temperature range of 90–150 °C was studied by means of in-situ X-ray diffraction (XRD). A “breakaway” in the oxidation kinetics is found at ∼0.25 μm, turning from a parabolic to a linear rate law. At the initial stage of oxidation the growth plane of UO{sub 2}(111) is the prominent one. As the oxide thickens, the growth rate of UO{sub 2}(220) plane increases and both planes grow concurrently. The activation energies obtained for the oxide growth are Q{sub parabolic} = 17.5 kcal/mol and Q{sub linear} = 19 kcal/mol. Enhanced oxidation around uranium carbide (UC) inclusions is clearly observed by scanning electron microscopy (SEM).

Two Pilot Plant Reactors Designed for the In Situ Bioremediation of Chlorobenzene-contaminated Ground Water: Hydrogeological and Chemical Characteristics and Bacterial Consortia

Energy Technology Data Exchange (ETDEWEB)

Vogt, Carsten, E-mail: vogt@umb.ufz.de; Alfreider, Albin [UFZ Centre for Environmental Research, Department of Environmental Microbiology (Germany); Lorbeer, Helmut [University of Technology Dresden, Institute of Waste Management and Contaminated Site Treatment (Germany); Ahlheim, Joerg; Feist, Bernd [UFZ Centre for Environmental Research, Department of Industrial and Mining Landscapes (Germany); Boehme, Olaf [GFE GmbH Halle (Germany); Weiss, Holger [UFZ Centre for Environmental Research, Department of Industrial and Mining Landscapes (Germany); Babel, Wolfgang; Wuensche, Lothar [UFZ Centre for Environmental Research, Department of Environmental Microbiology (Germany)

2002-05-15

The SAFIRA in situ pilot plant in Bitterfeld, Saxonia-Anhalt, Germany, currently serves as the test site for eight different in situ approaches to remediate anoxic chlorobenzene (CB)-contaminated ground water. Two reactors, both filled with original lignite-containing aquifer material, are designed for the microbiological in situ remediation of the ground water by the indigenous microbial consortia. In this study, the hydrogeological, chemical and microbiological conditions of the in flowing ground water and reactor filling material are presented,in order to establish the scientific basis for the start of the bioremediation process itself. The reactors were put into operation in June 1999. In the following, inflow CB concentrations in the ground water varied between 22 and 33 mg L{sup -1}; a chemical steady state for CB in both reactors was reached after 210 till 260 days operation time. The sediments were colonized by high numbers of aerobic, iron-reducing and denitrifying bacteria, as determined after 244 and 285 days of operation time. Furthermore, aerobic CB-degrading bacteria were detected in all reactor zones. Comparative sequence analysis of16S rDNA gene clone libraries suggest the dominance of Proteobacteria (Comamonadaceae, Alcaligenaceae, Gallionella group, Acidithiobacillus) and members of the class of low G+C gram-positive bacteria in the reactor sediments. In the inflowing ground water, sequences with phylogenetic affiliation to sulfate-reducing bacteria and sequences not affiliated with the known phyla of Bacteria, were found.

Two Pilot Plant Reactors Designed for the In Situ Bioremediation of Chlorobenzene-contaminated Ground Water: Hydrogeological and Chemical Characteristics and Bacterial Consortia

International Nuclear Information System (INIS)

Vogt, Carsten; Alfreider, Albin; Lorbeer, Helmut; Ahlheim, Joerg; Feist, Bernd; Boehme, Olaf; Weiss, Holger; Babel, Wolfgang; Wuensche, Lothar

2002-01-01

The SAFIRA in situ pilot plant in Bitterfeld, Saxonia-Anhalt, Germany, currently serves as the test site for eight different in situ approaches to remediate anoxic chlorobenzene (CB)-contaminated ground water. Two reactors, both filled with original lignite-containing aquifer material, are designed for the microbiological in situ remediation of the ground water by the indigenous microbial consortia. In this study, the hydrogeological, chemical and microbiological conditions of the in flowing ground water and reactor filling material are presented,in order to establish the scientific basis for the start of the bioremediation process itself. The reactors were put into operation in June 1999. In the following, inflow CB concentrations in the ground water varied between 22 and 33 mg L -1 ; a chemical steady state for CB in both reactors was reached after 210 till 260 days operation time. The sediments were colonized by high numbers of aerobic, iron-reducing and denitrifying bacteria, as determined after 244 and 285 days of operation time. Furthermore, aerobic CB-degrading bacteria were detected in all reactor zones. Comparative sequence analysis of16S rDNA gene clone libraries suggest the dominance of Proteobacteria (Comamonadaceae, Alcaligenaceae, Gallionella group, Acidithiobacillus) and members of the class of low G+C gram-positive bacteria in the reactor sediments. In the inflowing ground water, sequences with phylogenetic affiliation to sulfate-reducing bacteria and sequences not affiliated with the known phyla of Bacteria, were found

Bioremediation of fossil fuel contaminated soils

International Nuclear Information System (INIS)

Atlas, R.M.

1991-01-01

Bioremediation involves the use of microorganisms and their biodegradative capacity to remove pollutants. The byproducts of effective bioremediation, such as water and carbon dioxide, are nontoxic and can be accommodated without harm to the environment and living organisms. This paper reports that using bioremediation to remove pollutants has many advantages. This method is cheap, whereas physical methods for decontaminating the environment are extraordinarily expensive. Neither government nor private industry can afford the cost to clean up physically the nation's known toxic waste sites. Therefore, a renewed interest in bioremediation has developed. Whereas current technologies call for moving large quantities of toxic waste and its associated contaminated soil to incinerators, bioremediation can be done on site and requires simple equipment that is readily available. Bioremediation, though, is not the solution for all environmental pollution problems. Like other technologies, bioremediation has limitations

Heavy Metal Polluted Soils: Effect on Plants and Bioremediation Methods

OpenAIRE

Chibuike, G. U.; Obiora, S. C.

2014-01-01

Soils polluted with heavy metals have become common across the globe due to increase in geologic and anthropogenic activities. Plants growing on these soils show a reduction in growth, performance, and yield. Bioremediation is an effective method of treating heavy metal polluted soils. It is a widely accepted method that is mostly carried out in situ; hence it is suitable for the establishment/reestablishment of crops on treated soils. Microorganisms and plants employ different mechanisms for...

The design and construction of the bottom working for in-situ leaching of fragmented uranium ore by blasting in No. 745 mine

International Nuclear Information System (INIS)

Ding Dexin; Yang Shijiao; Li Ming

1998-11-01

Bottom working is a very important structure for in-situ leaching of fragmented uranium ore by blasting. Its design and construction should simultaneously satisfy the requirements for receiving fragmented ore, transporting the ore, providing relief space for blast operation, passage for workers and fresh air for the slope and collecting the pregnant solution from spraying over the fragmented ore. The author deals with the design and construction of the complete water cutoff bottom working for collecting the pregnant solution for in-situ leaching of fragmented uranium ore by long hole blast in No. 745 mine in Guangdong Province. The preparation system for the block, the undercutting, the construction process and method of the bottom working and the measures to guide the solution leaked into the surrounding rock mass to the bottom of the block are described in detail

Application of a new technology for reprocessing of wastes within the framework of rehabilitation of uranium mines operated by in situ leaching - 59403

International Nuclear Information System (INIS)

Martoyan, Gagik; Nalbandyan, Garik; Gagiyan, Lavrenti; Karamyan, Gagik; Barseghyan, Artak; Brutyan, Gagik

2012-01-01

It is essential the environmentally safe industrial production of nuclear fuel especially in the case of uranium extraction by In Situ Leaching, when the environment and the deep extraction of uranium are important problems. In the presented paper it is studied the feasibility of the application of an electro-dialysis method for the deep extraction of uranium and radium from liquid (acid) streams. It is proposed to apply a new electro-hydro-metallurgical [1] extraction and refining method to ensure the necessary extraction level of elements. In the same time the new method ensures the recycling of acids used in the process. The above mentioned two different demonstrations of the new electro-hydro-metallurgical technology show that important environmental problems, such as the removal of harmful liquid-radioactive wastes, are solved in the most economical and energy efficient manner, while a new avenue has also opened for its large-scale use in mining industry. In particular, we offer this method to reprocess the huge quantity of wastes accumulated on uranium mines sites within the rehabilitation work of uranium mines operated by In Situ Leaching. A corresponding electro-hydro-metallurgical plant (mobile and stationary units) is designed for the large-scale extraction and refining of all elements from the wastes of uranium mines, which has a very high level of environmental safety, for an industry that so far has caused considerable environmental harm. The new plant design has no smokestacks, nor the emission of environmentally hazardous elements and its operation is characterized by high energy efficiency, which translates to high economy, while all materials used in the processing stages are fully reconstituted and recycled. (authors)

Molecular interactions of Leucoagaricus naucinus with uranium(VI) and europium(III)

Energy Technology Data Exchange (ETDEWEB)

Wollenberg, Anne; Raff, Johannes [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Biogeochemistry; Guenther, A. [Helmholtz Institute Freiberg for Resource Technology, Freiberg (Germany)

2017-06-01

With regard to a molecular understanding of the interaction of fungal mycelium with radionuclides and its possible application for precautionary radiation protection and bio-remediation, the binding mechanism of the radionuclide uranium and the metal europium, as surrogate for trivalent actinides, where investigated with different starting conditions by the living fungal cells of Leucoagaricus naucinus.

Molecular interactions of Leucoagaricus naucinus with uranium(VI) and europium(III)

International Nuclear Information System (INIS)

Wollenberg, Anne; Raff, Johannes

2017-01-01

With regard to a molecular understanding of the interaction of fungal mycelium with radionuclides and its possible application for precautionary radiation protection and bio-remediation, the binding mechanism of the radionuclide uranium and the metal europium, as surrogate for trivalent actinides, where investigated with different starting conditions by the living fungal cells of Leucoagaricus naucinus.

Uranium industry in the USSR

International Nuclear Information System (INIS)

Nikipelov, B.V.; Chernov, A.G.

1990-01-01

A brief historical account of the Soviet production of natural and enriched uranium is given. The geological and geographical location of major uranium deposits are mentioned. The processing of natural ores including in-situ leaching (ISL) is also briefly described. Gas centrifuges play a large part in uranium enrichment. The role of Techsnabexport for the export of nuclear materials is explained

Bioremediation studies of tailing ponds of uranium mines

International Nuclear Information System (INIS)

Sudhakar, G.; Muralidhar Rao, C.; Swaminathan, Siva Kumar

2012-01-01

A study was undertaken for three years to evaluate the potential of native plant species for the phytoremediation of tailing ponds of Uranium mines, Jaduguda, Jharkhand. Five sampling stations: three at Jaduguda (TP1, TP2, and TP3), one at Turamdih (TTP) and one at Effluent Treatment Plant (ETP) were selected. pH, Electrical conductivity (EC), 12 metals (- AI, V, Cr, Mn, Fe, Ni, Cu, Zn, As, Se, Cd, Pb) and 3 radionuclides - Co, Sr and U) were analysed. From the analysis of sediment/soil/water/effluent of tailing ponds, 4 elements - U, Mn, AI and Fe were found to be significantly in higher concentrations in water, and 8-elements (U, Mn, V, Fe, Ni, Cu and Zn) were found to be in higher concentrations in soils. U and Mn were found to be the predominant contaminants. 26 plant species were screened for their ability to accumulate and remediate the contaminated soils of which only four plant species - one fern (Pteris vittata - P. vittata), one terrestrial (Saccharum spontaneum - S. spontaneum ) and two aquatic species (Typha latifolia - T. latifolia, Cyperus compressus - C. compressus) were shortlisted for phytoremediation studies in laboratory condition and transfer factors were calculated. The results of the study under controlled conditions indicate that P. vittata, S. spontaneum, T. latifolia and C. compressus were found to be the candidate species for phytoremediation of Uranium mine tailings. (author)

Use of thermophilic bacteria for bioremediation of petroleum contaminants

International Nuclear Information System (INIS)

Al-Maghrabi, I.M.A.; Bin Aqil, A.O.; Chaalal, O.; Islam, M.R.

1999-01-01

Several strains of thermophilic bacteria were isolated from the environment of the United Arab Emirates. These bacteria show extraordinary resistance to heat and have their maximum growth rate around 60--80 C. This article investigates the potential of using these facultative bacteria for both in situ and ex situ bioremediation of petroleum contaminants. In a series of batch experiments, bacterial growth was observed using a computer image analyzer following a recently developed technique. These experiments showed clearly that the growth rate is enhanced in the presence of crude oil. This is coupled with a rapid degradation of the crude oil. These bacteria were found to be ideal for breaking down long-chain organic molecules at a temperature of 40 C, which is the typical ambient temperature of the Persian Gulf region. The same strains of bacteria are also capable of surviving in the presence of the saline environment that can prevail in both sea water and reservoir connate water. This observation prompted further investigation into the applicability of the bacteria in microbial enhanced oil recovery. In the United Arab Emirates, the reservoirs are typically at a temperature of around 85 C. Finally, the performance of the bacteria is tested in a newly developed bioreactor that uses continuous aeration through a transverse slotted pipe. This reactor also uses mixing without damaging the filamentous bacteria. In this process, the mechanisms of bioremediation are identified

Licensing Status of New and Expanding In-Situ Recovery Uranium Projects in the United States

Energy Technology Data Exchange (ETDEWEB)

Catchpole, G.; Thomas, M., E-mail: gccatchpole@uranerz.com [Uranerz Energy Corporation (URZ), Casper, WY (United States)

2014-05-15

The authors investigated the licensing status of new in-situ recovery (“ISR”) uranium projects, as well as the expansion of existing projects, within the United States (“US”). Specific emphasis and analysis is placed on those projects within the states of Texas and Wyoming. Of note, information used to prepare this paper was obtained from public sources that included company web sites, the US Securities and Exchange Commission, the US Nuclear Regulatory Commission (“NRC”), the US Energy Information Agency (“EIA”), and the relevant state regulatory agencies. The renewed interest in the production of natural uranium has been motivated, in part, by the increased sale price of yellowcake beginning around 2003 resulting in numerous new and existing natural resources companies acquiring mineral rights in the United States. Because of the economic favorability in terms of both operating and capital costs of ISR mines versus conventional mines in the US (with its relatively low grade of uranium ore), the model for most companies was to acquire mineral properties that had the potential for being mined using the ISR method. There were, however, exceptions to this model. The Uravan mineral district in southwest Colorado and southeast Utah, where relatively high-grade, shallow uranium deposits have the potential to be mined using underground methods, is one such exception. However, the focus of this paper will be on ISR projects. In Wyoming, which has been the top producer of natural uranium among the 50 states for the past seven years, there is one producing ISR mine (Bill Smith — Highland), one ISR mine on standby (Christensen Ranch), and two ISR uranium projects licensed but not yet built (Gas Hills and North Butte). Cameco Resources is planning to develop two ISR projects in Wyoming that have been licensed but not yet constructed. Additionally, three new uranium companies (Ur-Energy, Uranerz and Uranium One) have filed applications with the federal and

Arctic bioremediation

International Nuclear Information System (INIS)

Lidell, B.V.; Smallbeck, D.R.; Ramert, P.C.

1991-01-01

Cleanup of oil and diesel spills on gravel pads in the Arctic has typically been accomplished by utilizing a water flushing technique to remove the gross contamination or excavating the spill area and placing the material into a lined pit, or a combination of both. Enhancing the biological degradation of hydrocarbon (bioremediation) by adding nutrients to the spill area has been demonstrated to be an effective cleanup tool in more temperate locations. However, this technique has never been considered for restoration in the Arctic because the process of microbial degradation of hydrocarbon in this area is very slow. The short growing season and apparent lack of nutrients in the gravel pads were thought to be detrimental to using bioremediation to cleanup Arctic oil spills. This paper discusses the potential to utilize bioremediation as an effective method to clean up hydrocarbon spills in the northern latitudes

36Cl production in situ, and groundwater transport in a uranium ore deposit

International Nuclear Information System (INIS)

Cornett, R.J.; Andrews, H.R.; Brown, R.M.; Chant, L.A.; Cramer, J.; Davies, W.G.; Greiner, B.F.; Imahori, Y.; Koslowsky, V.T.; McKay, J.W.; Milton, G.M.; Milton, J.D.C.

1992-01-01

The authors have used AMS to measure 36 Cl concentrations produced in situ in ore and in groundwater within the 1.3 billion year old Cigar Lake uranium ore deposit. 36 Cl concentrations are up to 300 times higher in the ore zone than in the surrounding aquifer. Based on 36 Cl ingrowth, the authors calculate the residence time of water within the ore zone to be 100,000 to 300,000 years. Since the geologic setting of this deposit is a very close natural analogue to a proposed nuclear fuel waste repository, this analysis demonstrates that natural geological barriers can effectively isolate mobile radionuclides from an open, regional groundwater flow system over millennia

In silico Analysis for Laccase-mediated Bioremediation of the Emerging Pharmaceutical Pollutants

Directory of Open Access Journals (Sweden)

Anjali Singh

2015-12-01

Full Text Available Laccases, a copper oxidase enzyme, has been employed for bioremediation of anthropogenic pollutants in the recent past. Laccase has a broad range of substrate specificity which offers the prospect for screening in numerable xenobiotics. The present study was aimed to use protein-ligand docking as a tool for prediction of biodegradation of selected pharmaceutical pollutants. A comparative study was also done to determine the binding efficacy of bacterial and fungal laccase for those selected pollutants. The laccase-pollutant docking was carried out using HEX software. The docking scores of bacterial and fungal laccase for predefined pollutants were comparable to ABTS, a substrate for laccase, which suggested that laccase might be able to degrade emerging pharmaceutical pollutants. The docking analysis approach can be useful in prediction of binding competence of pharmaceutical pollutants with laccase for in situ laccase-mediated bioremediation.

An evaluation of bioremediation of oiled sediments buried within a mudflat environment

International Nuclear Information System (INIS)

Swannell, R. P. J.; Mitchell, D. J.; Jones, D. M.; Willis, A. L.; Lee, K.

1997-01-01

An investigation was carried out to determine the potential of bioremediation to treat an oil-contaminated shoreline sediment in the southwest of England. The specific objective was to determine whether periodic additions of inorganic nitrate and phosphate could be used to enhance the biodegradation rate of weathered and emulsified Arabian Light crude oil-contaminated sediment stranded on the beach at a depth of about 15 cm. To measure the potential for successful treatment, changes in the chemical composition and concentration of residual hydrocarbons, microbial carbon dioxide production rates in situ and in the hydrocarbon-degrading microbial community, were monitored. Results showed that regular additions of inorganic nutrients significantly enhanced the rate of oil biodegradation in comparison with unfertilized oil sediments, indicating that bioremediation could be successful in treating buried oil in aerobic fine sediments.17 refs., 4 tabs., 4 figs

Site characterization for the in situ bioremediation of the vadose zone

International Nuclear Information System (INIS)

Montemagno, C.D.; Leo, A.; Craig, J.

1993-01-01

Studies were conducted to determine whether bioremediation can be used to treat a diesel fuel spill in the deep vadose zone (>30 m). After laboratory studies confirmed the ability of the natural population of organisms to degrade the diesel fuel, the technological issue of transporting the required mass of nutrients to the contaminated soils was addressed. Laboratory studies demonstrated that nutrient and oxygen transport can be enhanced by the addition of divalent cations to injected waters. This addition of minerals caused the observed hydraulic conductivity to be maintained at elevated levels that allowed the macronutrient nitrogen, provided as ammonium ion, to be more uniformly distributed to target soil domains

Laser-induced breakdown spectroscopy measurements of uranium and thorium powders and uranium ore

Energy Technology Data Exchange (ETDEWEB)

Judge, Elizabeth J. [Chemistry Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Barefield, James E., E-mail: jbarefield@lanl.gov [Chemistry Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Berg, John M. [Manufacturing Engineering and Technology Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Clegg, Samuel M.; Havrilla, George J.; Montoya, Velma M.; Le, Loan A.; Lopez, Leon N. [Chemistry Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States)

2013-05-01

Laser-induced breakdown spectroscopy (LIBS) was used to analyze depleted uranium and thorium oxide powders and uranium ore as a potential rapid in situ analysis technique in nuclear production facilities, environmental sampling, and in-field forensic applications. Material such as pressed pellets and metals, has been extensively studied using LIBS due to the high density of the material and more stable laser-induced plasma formation. Powders, on the other hand, are difficult to analyze using LIBS since ejection and removal of the powder occur in the laser interaction region. The capability of analyzing powders is important in allowing for rapid analysis of suspicious materials, environmental samples, or trace contamination on surfaces since it most closely represents field samples (soil, small particles, debris etc.). The rapid, in situ analysis of samples, including nuclear materials, also reduces costs in sample collection, transportation, sample preparation, and analysis time. Here we demonstrate the detection of actinides in oxide powders and within a uranium ore sample as both pressed pellets and powders on carbon adhesive discs for spectral comparison. The acquired LIBS spectra for both forms of the samples differ in overall intensity but yield a similar distribution of atomic emission spectral lines. - Highlights: • LIBS analysis of mixed actinide samples: depleted uranium oxide and thorium oxide • LIBS analysis of actinide samples in powder form on carbon adhesive discs • Detection of uranium in a complex matrix (uranium ore) as a precursor to analyzing uranium in environmental samples.

Biosurfactant-enhanced soil bioremediation

Energy Technology Data Exchange (ETDEWEB)

Kosaric, N.; Lu, G.; Velikonja, J. [Univ. of Western Ontario, London, Ontario (Canada)

1995-12-01

Bioremediation of soil contaminated with organic chemicals is a viable alternative method for clean-up and remedy of hazardous waste sites. The final objective in this approach is to convert the parent toxicant into a readily biodegradable product which is harmless to human health and/or the environment. Biodegradation of hydrocarbons in soil can also efficiently be enhanced by addition or in-situ production of biosufactants. It was generally observed that the degradation time was shortened and particularly the adaptation time for the microbes. More data from our laboratories showed that chlorinated aromatic compounds, such as 2,4-dichlorophenol, a herbicide Metolachlor, as well as naphthalene are degraded faster and more completely when selected biosurfactants are added to the soil. More recent data demonstrated an enhanced biodegradation of heavy hydrocarbons in petrochemical sludges, and in contaminated oil when biosurfactants were present or were added prior to the biodegradation process.

Study and application of new chelating resin to recovery uranium from in-situ leach solution with high content saline chloride ion

International Nuclear Information System (INIS)

Zhang Jianguo; Qiu Yueshuang; Feng Yu; Deng Huidong; Zhao Chaoya

2014-01-01

Research on the adsorption and elution property of D814 chelating resin was carried out aiming at the difficult separation of uranium from high content saline chloride ion in situ leach liquor and the adsorption mechanism is also discussed. Influence factors such as contact time, pH value, Ca"2"+, Mg"2"+ and Cl"- concentration etc. to the resin adsorption were studied. Experimental results show that adsorption rate is lowly which need 6h to arrive at the adsorption equilibrium. The resin adsorption uranium pH in the solution is from l.33 to 9. When total salinity is over 20 g/L, calcium ion, and magnesium ion is about 3 g/L, there are no big influence on resin adsorption capacity. The resin has good chloride ion resistance. When chloride ion is over 60 g/L, it is no influence on resin adsorption uranium. Column experiment results indicate that ratio of saturation volume to break-through point volume is l.82, resin saturation uranium capacity is 40.5 mg. U/_g_(_∓_)_R. When elution volume bed number is 23, the eluted solution uranium concentration is below 80 mg/L. The elution rate of the uranium is 96.2%. (authors)

In-situ neutron diffraction characterization of temperature dependence deformation in α-uranium

Science.gov (United States)

Calhoun, C. A.; Garlea, E.; Sisneros, T. A.; Agnew, S. R.

2018-04-01

In-situ strain neutron diffraction measurements were conducted at temperature on specimens coming from a clock-rolled α-uranium plate, and Elasto-Plastic Self-Consistent (EPSC) modeling was employed to interpret the findings. The modeling revealed that the active slip systems exhibit a thermally activated response, while deformation twinning remains athermal over the temperature ranges explored (25-150 °C). The modeling also allowed assessment of the effects of thermal residual stresses on the mechanical response during compression. These results are consistent with those from a prior study of room-temperature deformation, indicating that the thermal residual stresses strongly influence the internal strain evolution of grain families, as monitored with neutron diffraction, even though accounting for these residual stresses has little effect on the macroscopic flow curve, except in the elasto-plastic transition.

78 FR 17450 - Notice of Issuance of Materials License Renewal, Operating License SUA-1341, Uranium One USA, Inc...

Science.gov (United States)

2013-03-21

... License Renewal, Operating License SUA-1341, Uranium One USA, Inc., Willow Creek Uranium In Situ Recovery.... SUA- 1341 to Uranium One USA, Inc. (Uranium One) for its Willow Creek Uranium In Situ Recovery (ISR... Commission License No. SUA-1341 For Uranium One USA, Inc., Irigaray and Christensen Ranch Projects (Willow...

Arctic bioremediation

International Nuclear Information System (INIS)

Liddell, B.V.; Smallbeck, D.R.; Ramert, P.C.

1991-01-01

Cleanup of oil and diesel spills on gravel pads in the Arctic has typically been accomplished by utilizing a water flushing technique to remove the gross contamination or excavating the spill area and placing the material into a lined pit, or a combination of both. This paper discusses the potential to utilize bioremediation as an effective method to clean up hydrocarbon spills in the northern latitudes. Discussed are the results of a laboratory bioremediation study which simulated microbial degradation of hydrocarbon under arctic conditions

Remediation of uranium in-situ leaching area at Straz Pod Ralskem, Czech Republic

Energy Technology Data Exchange (ETDEWEB)

Vokal, Vojtech; Muzak, Jiri; Ekert, Vladimir [DIAMO, s. e., TUU, Pod Vinici 84, Straz pod Ralskem, 471 27 (Czech Republic)

2013-07-01

A large-scale development in exploration and production of uranium ores in the Czech Republic was done in the 2nd half of the 20. century. Many uranium deposits were discovered in the territory of the Czech Republic. One of the most considerable deposits in the Czech Republic is the site Hamr na Jezere - Straz pod Ralskem where both mining methods - the underground mining and the acidic in-situ leaching - were used. The extensive production of uranium led to widespread environmental impacts and contamination of ground waters. Over the period of 'chemical' leaching of uranium (ca. 32 years), a total of more than 4 million tons of sulphuric acid and other chemicals have been injected into the ground. Most of the products (approx. 99.5 %) of the acids reactions with the rocks are located in the Cenomanian aquifer. The contamination of Cenomanian aquifer covers the area larger then 27 km{sup 2}. The influenced volume of groundwater is more than 380 million m{sup 3}. The total amount of dissolved SO{sub 4}{sup 2-} is about 3.6 million tons. After 1990 a large-scale environmental program was established and the Czech government decided to liquidate the ISL Mine and start the remediation in 1996. The remediation consists of contaminated groundwater pumping, removing of the contaminants and discharging or reinjection of treated water. Nowadays four main remedial technological installations with sufficient capacity for reaching of the target values of remedial parameters in 2037 are used - the 'Station for Acid Solutions Liquidation No. One', the 'Mother liquor reprocessing' station, the 'Neutralization and Decontamination Station NDS 6' and the 'Neutralization and Decontamination Station NDS 10'. It is expected that the amount of withdrawn contaminants will vary from 80 000 to 120 000 tons per year. Total costs of all remediation activities are expected to be in excess of 2 billion EUR. (authors)

Bioremediation protocols

National Research Council Canada - National Science Library

Sheehan, David

1997-01-01

... . . .. .. . . . .. . . .. . . . . . .. . . . . . .. . . . .. . .. . . . . . . .. . . . .., . .. . . . . *... *.. . . . . . . .. . .. . . . . . . . .. .. .. . . . . . v IX PART I. OVERVIEW ., .,... . ,.. .. . . . . . . .. .. . . ., 7 1 Uses Emer of Bacteria Colleran in Bioremediation...

Bioclogging Effects Relevant to In-Situ Bioremediation of Organic Contaminants

Science.gov (United States)

Bielefeldt, A. R.; Illangasekare, T.

2002-05-01

environments. The implications of ignoring bioclogging effects of the magnitude measured in the experimental systems when predicting contaminant plumes in the subsurface will be illustrated using simple models that incorporate biokinetics and hydrodynamic effects. The models will show the importance of including bioclogging effects when designing enhanced in-situ bioremediation systems.

Working and benefit project by the in-situ leaching of the copper-uranium ore of the deposit named Luz del Cobre, in the municipality of Soyopa, state of Sonora, Mexico

International Nuclear Information System (INIS)

Parga P, J.de J.

1976-01-01

This research was carried out with the object to recover the existing uranium in the copper-uranium deposit of Luz del Cobre located at 1300 Kms. approximately of the NW of Mexico City in the state of Sonora this deposit is geologically formed by a partially mineralized chimney which contains 572,732 tons of uranium ore with an average of 362.26g. of U 3 O 8 per ton, which represents 207,374 tons of U 3 O 8 in situ. To recover the uranium from this deposit, the only technical and economical possibility which presents a real interest is the system of leaching in situ. This operation will consist in the selective dissolution of the copper and uranium through leaching solution with a pH varying from 2.2 to 2.5, leaving the gangue on the ground and collecting the enriched solutions at the lower level of the mine, precipitating the copper subsequently through scrap iron and recovering the uranium from the tails of the copper precipitation plant through an ionic interchange process in counter current and its subsequent elution solvent extraction, reextraction and precipitation. This system makes possible to recover an uranium concentrate up to 98% of U 3 O 8 and practically free from impurities. The production cost would cost exceeding $300.00 Mexican currency per Kg of U 3 O 8 . (author)

Characterization of uranium bioaccumulation on a fungal isolate Geotrichum sp. dwc-1 as investigated by FTIR, TEM and XPS

International Nuclear Information System (INIS)

Changsong Zhao; Congcong Ding; Jiali Liao; Jijun Yang; Yuanyou Yang; Jun Tang; Ning Liu; Qun Sun

2016-01-01

In this paper, TEM-EDX, FTIR, XPS, PIXE, and EPBS were employed to identify the uranium biosorption behavior and the potential mechanism on cells of Geotrichum sp. dwc-1, isolated from soils. These results displayed that the biosorption behavior was greatly dependent on pH and uranium was absorbed by bounding to amino, phosphate as well as carboxyl functional groups. Uranium biosorption behavior on Geotrichum sp. dwc-1 involves bioaccumulation, electrostatic interaction and ion exchange process. This work throws further light on potential fungal roles these mechanisms for elemental recovery and bioremediation. (author)

Push-pull test: a method of evaluating formation adsorption parameters for predicting the environmental effects on in situ coal gasification and uranium recovery

International Nuclear Information System (INIS)

Drever, J.I.; McKee, C.R.

1980-11-01

The push-pull test, which is a simple injection and pumping sequence of groundwater spiked with solutes of interest, is presented as a method of determining the adsorption characteristics of a formation. Adsorption properties are necessary to predict restoration from both in situ coal gasification and in situ uranium extraction. The major problems in applying laboratory measurements to the field concern scaling the effect of particle size and obtaining representative samples. Laboratory measurements are conducted on gram to kilogram scale samples, whereas the push-pull test evaluates a sample weighing approximately 130 to 1000 metric tons, depending on volume injected and porosity. The problem in translating laboratory results to the field appear to be less severe for sedimentary uranium bodies than for coal. Laboratory measurements are useful in delineating ranges in adsorption properties and in planning the field experiment. Two field push-pull tests were conducted on uranium formations in Wyoming. Adsorption properties estimated from these tests on the basis of a simple cell model were compared to the laboratory values. In the first case, excellent agreement was observed between the values estimated from the field test and the values measured in the laboratory. In the second case, the value for K/sub d/ determined in the laboratory was five times higher than the field value. It is recommended that push-pull tests be conducted on coal formations being considered for in situ gasification in view of the great uncertainty in extrapolating laboratory adsorption properties to the field

Postremediation bioremediation

International Nuclear Information System (INIS)

Brown, R.A.; Hicks, P.M.; Hicks, R.J.; Leahy, M.C.

1995-01-01

In applying remediation technology, an important question is when to stop operations. Conventional wisdom states that each site has a limit of treatability. Beyond a point, the site conditions limit access to residual contaminants and, therefore, treatment effectiveness. In the treatment of petroleum hydrocarbons, the issue in ceasing remedial operations is not what is the limit of treatment, but what should be the limit of effort. Because hydrocarbons are inherently biodegradable, there is a point in remediation where natural or intrinsic bioremediation is adequate to complete the remedial process. This point is reached when the rate of residual carbon release is the limiting factor, not the rate of oxygen or nutrient supply. At such a point, the rate and degree of remediation is the same whether an active system is being applied or whether nothing is being actively done. This paper presents data from several bioremediation projects where active remediation was terminated above the desired closure levels. These site data illustrate that intrinsic bioremediation is as effective in site closure as continued active remediation

Bioremediation potential of a newly isolate solvent tolerant strain Bacillus thermophilus PS11

Directory of Open Access Journals (Sweden)

PAYEL SARKAR

2012-01-01

Full Text Available The increased generation of solvent waste has been stated as one of the most critical environmental problems. Though microbial bioremediation has been widely used for waste treatment but their application in solvent waste treatment is limited since the solvents have toxic effects on the microbial cells. A solvent tolerant strain of Bacillus thermophilus PS11 was isolated from soil by cyclohexane enrichment. Transmission electron micrograph of PS11 showed convoluted cell membrane and accumulation of solvents in the cytoplasm, indicating the adaptation of the bacterial strain to the solvent after 48h of incubation. The strain was also capable of growing in presence of wide range of other hydrophobic solvents with log P-values below 3.5. The isolate could uptake 50 ng/ml of uranium in its initial 12h of growth, exhibiting both solvent tolerance and metal resistance property. This combination of solvent tolerance and metal resistance will make the isolated Bacillus thermophilus PS11 a potential tool for metal bioremediation in solvent rich wastewaters.

75 FR 62153 - Notice of the Nuclear Regulatory Commission Issuance of Materials License SUA-1596 for Uranium...

Science.gov (United States)

2010-10-07

... Commission Issuance of Materials License SUA-1596 for Uranium One Americas, Inc. Moore Ranch In Situ Recovery.... SUPPLEMENTARY INFORMATION: The Nuclear Regulatory Commission (NRC) has issued a license to Uranium One Americas, Inc. (Uranium One) for its Moore Ranch uranium in situ recovery (ISR) facility in Campbell County...

Effectiveness of bioremediation in reducing toxicity in oiled intertidal sediments

International Nuclear Information System (INIS)

Lee, K.; Tremblay, G.H.

1995-01-01

A 123-day field study was conducted with in situ enclosures to compare the effectiveness of bioremediation strategies based in inorganic and organic fertilizer additions to accelerate the biodegradation rates and reduce the toxicity of Venture trademark condensate stranded within sand-beach sediments. Comparison of the two fertilizer formulations with identical nitrogen and phosphorus concentrations showed that the organic fertilizer stimulated bacterial productivity within the oiled sediments to the greatest extent. However, detailed chemical analysis indicated that inorganic fertilizer additions were the most effective in enhancing condensate biodegradation rates. The Microtox reg-sign Solid-Phase Test (SPT) bioassay was determined to be sensitive to Venture Condensate in laboratory tests. Subsequent application of this procedure to oiled sediment in the field showed a reduction in sediment toxicity over time. However, the Microtox reg-sign bioassay procedure did not identify significant reductions in sediment toxicity following bioremediation treatment. An observed increase in toxicity following periodic additions of the organic fertilizer was attributed to rapid biodegradation rates of the fertilizer, which resulted in the production of toxic metabolic products

To meet new tasks of scientific research on uranium geology in new century

International Nuclear Information System (INIS)

Chen Zuyi

2000-01-01

The author analyses the new situation that the scientific research on uranium geology is facing in the coming new century, and proposes that the guiding idea of the scientific research on uranium geology is to coordinate the general policy of Bureau of Geology--to give the first priority to in-situ leachable sandstone-type uranium deposits. The specific tasks for the scientific research on uranium geology are: to implement regional evaluation and target area selection of in-situ leachable sandstone-type uranium deposits; to develop new techniques and methods of detecting buried in-situ leachable sandstone-type uranium deposits; to turn the genetic model of uranium deposit and deposit model to prospecting model; to strengthen the research on economic geology and the dynamic assessment system of uranium resources and to build up and improve the data base of Meso-Cenozoic basins and sandstone-type uranium deposits. In order to guarantee the successful implementation of the above tasks it is necessary for the Beijing Research Institute of Uranium Geology--the leading unit in scientific research on uranium geology to accelerate bringing up large numbers of young outstanding researchers; to have clear consciousness of market economy and product quality; to given play to advantages of qualified personnel, advanced equipment and modern technology

In situ biorestauratie van een met olie verontreinigde bodem: Resultaten van het onderzoek in ongestoorde grondkolommen

NARCIS (Netherlands)

Scheuter AJ; Berg R van den; LBG

1996-01-01

Column experiments were carried out for the project "in situ bioremediation of an oil-polluted subsoil". The experiments were aimed at examining the possibility of remediating soil in situ with the help of microorganisms. The six undisturbed columns were filled at a location contaminated with petrol

In situ pilot test for bioremediation of energetic compound-contaminated soil at a former military demolition range site.

Science.gov (United States)

Jugnia, Louis B; Manno, Dominic; Drouin, Karine; Hendry, Meghan

2018-05-04

Bioremediation was performed in situ at a former military range site to assess the performance of native bacteria in degrading hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) and 2,4-dinitrotoluene (2,4-DNT). The fate of these pollutants in soil and soil pore water was investigated as influenced by waste glycerol amendment to the soil. Following waste glycerol application, there was an accumulation of organic carbon that promoted microbial activity, converting organic carbon into acetate and propionate, which are intermediate compounds in anaerobic processes. This augmentation of anaerobic activity strongly correlated to a noticeable reduction in RDX concentrations in the amended soil. Changes in concentrations of RDX in pore water were similar to those observed in the soil suggesting that RDX leaching from the soil matrix, and treatment with waste glycerol, contributed to the enhanced removal of RDX from the water and soil. This was not the case with 2,4-DNT, which was neither found in pore water nor affected by the waste glycerol treatment. Results from saturated conditions and Synthetic Precipitation Leaching Procedure testing, to investigate the environmental fate of 2,4-DNT, indicated that 2,4-DNT found on site was relatively inert and was likely to remain in its current state on the site.

Bioremediation protocols

National Research Council Canada - National Science Library

Sheehan, David

1997-01-01

..., .. . . . . .. ,. . . .. . . . . . . . .. . . . . .. . . .. . .. 3 2 Granular Nina Sludge Christiansen, Consortia lndra for Bioremediation, M. Mathrani, and Birgitte K. Ahring . 23 PART II PROTOCOLS...

Uranium: Memories of the Little Big Horn

International Nuclear Information System (INIS)

White, G. Jr.

1985-01-01

In this work the author discusses the future of the uranium industry. The author believes that uranium prices are unlikely to rise to a level that predicates the rebirth of the uranium industry, and doubts that U.S. production of uranium will exceed 30 to 35 percent of U.S. requirements. The author doubts that the U.S. government will take any action toward protecting the U.S. uranium production industry, but he does believe that a U.S. uranium production industry will survive and include in-situ and by product producers and producers with higher grades and rigorous cost control

Raoultella sp. SM1, a novel iron-reducing and uranium-precipitating strain.

Science.gov (United States)

Sklodowska, Aleksandra; Mielnicki, Sebastian; Drewniak, Lukasz

2018-03-01

The main aim of this study was the characterisation of novel Raoutella isolate, an iron-reducing and uranium-precipitating strain, originating from microbial mats occurring in the sediments of a closed down uranium mine in Kowary (SW Poland). Characterisation was done in the context of its potential role in the functioning of these mats and the possibility to use them in uranium removal/recovery processes. In our experiment, we observed the biological precipitation of iron and uranium's secondary minerals containing oxygen, potassium, sodium and phosphor, which were identified as ningyoite-like minerals. The isolated strain, Raoultella sp. SM1, was also able to dissimilatory reduce iron (III) and uranium (VI) in the presence of citrate as an electron donor. Our studies allowed us to characterise a new strain which may be used as a model microorganism in the study of Fe and U respiratory processes and which may be useful in the bioremediation of uranium-contaminated waters and sediments. During this process, uranium may be immobilised in ningyoite-like minerals and can then be recovered in nano/micro-particle form, which may be easily transformed to uraninite. Copyright © 2017 Elsevier Ltd. All rights reserved.

Bioremediation of diesel from a rocky shoreline in an arid tropical climate.

Science.gov (United States)

Guerin, Turlough F

2015-10-15

A non invasive sampling and remediation strategy was developed and implemented at shoreline contaminated with spilt diesel. To treat the contamination, in a practical, cost-effective, and safe manner (to personnel working on the stockpiles and their ship loading activity), a non-invasive sampling and remediation strategy was designed and implemented since the location and nature of the impacted geology (rock fill) and sediment, precluded conventional ex-situ and any in-situ treatment where drilling is required. A bioremediation process using surfactant, and added N & P and increased aeration, increased the degradation rate allowing the site owner to meet their regulatory obligations. Petroleum hydrocarbons decreased from saturation concentrations to less than detectable amounts at the completion of treatment. Copyright © 2015 Elsevier Ltd. All rights reserved.

Uranium speciation and stability after reductive immobilization in aquifer sediments

Science.gov (United States)

Sharp, Jonathan O.; Lezama-Pacheco, Juan S.; Schofield, Eleanor J.; Junier, Pilar; Ulrich, Kai-Uwe; Chinni, Satya; Veeramani, Harish; Margot-Roquier, Camille; Webb, Samuel M.; Tebo, Bradley M.; Giammar, Daniel E.; Bargar, John R.; Bernier-Latmani, Rizlan

2011-11-01

It has generally been assumed that the bioreduction of hexavalent uranium in groundwater systems will result in the precipitation of immobile uraninite (UO 2). In order to explore the form and stability of uranium immobilized under these conditions, we introduced lactate (15 mM for 3 months) into flow-through columns containing sediments derived from a former uranium-processing site at Old Rifle, CO. This resulted in metal-reducing conditions as evidenced by concurrent uranium uptake and iron release. Despite initial augmentation with Shewanella oneidensis, bacteria belonging to the phylum Firmicutes dominated the biostimulated columns. The immobilization of uranium (˜1 mmol U per kg sediment) enabled analysis by X-ray absorption spectroscopy (XAS). Tetravalent uranium associated with these sediments did not have spectroscopic signatures representative of U-U shells or crystalline UO 2. Analysis by microfocused XAS revealed concentrated micrometer regions of solid U(IV) that had spectroscopic signatures consistent with bulk analyses and a poor proximal correlation (μm scale resolution) between U and Fe. A plausible explanation, supported by biogeochemical conditions and spectral interpretations, is uranium association with phosphoryl moieties found in biomass; hence implicating direct enzymatic uranium reduction. After the immobilization phase, two months of in situ exposure to oxic influent did not result in substantial uranium remobilization. Ex situ flow-through experiments demonstrated more rapid uranium mobilization than observed in column oxidation studies and indicated that sediment-associated U(IV) is more mobile than biogenic UO 2. This work suggests that in situ uranium bioimmobilization studies and subsurface modeling parameters should be expanded to account for non-uraninite U(IV) species associated with biomass.

Development of a stable uranium recovery regulatory framework for uranium recovery activities in the United States

International Nuclear Information System (INIS)

Layton, M.C.; Abrams, C.E.

2000-01-01

The U.S. Nuclear Regulatory Commission (NRC) has historically regulated operations at all uranium and thorium recovery facilities under the authority of the Atomic Energy Act of 1954, as amended. Uranium recovery facilities are those plants, or portions of facilities that process uranium- or thorium-bearing material primarily for its source material content. The uranium recovery industry expressed some concerns over several aspects of the NRC's practices, as described in the NRC's guidance documents. In April 1998, the National Mining Association submitted a report to the Commission, that identified specific concerns with NRC's current position and guidance regarding concurrent jurisdiction at uranium mills; dual regulatory authority at in situ leach facilities; the use of mill tailings impoundments for disposal of radioactive material other than 11e.(2) byproduct material; and the ability to process alternate feed material at uranium mills. The NRC staff addressed most of these concerns in two SECY (staff recommendations) papers that were concurrently provided to the Commission, along with a SECY paper on a draft rulemaking plan relating to these and other issues. The issues addressed in these papers included a new rulemaking, disposal of materials other than 11 e.(2) byproduct material, processing of materials other than natural ores, and improved efficiency for regulating in situ leach uranium facilities. The Commission issued final policy decisions on these issues and directions for NRC staff to implement those decisions in July 2000. (author)

Advancements in exploration and In-Situ Recovery of sedimentary hosted uranium

International Nuclear Information System (INIS)

Märten, H.; Marsland-Smith, A.; Ross, J.; Haschke, M.; Kalka, H.; Schubert, J.

2014-01-01

This paper describes recent advancements in exploration technologies for sedimentary-hosted uranium deposits as basis for improved model-based planning and optimization of in-situ recovery (ISR). High-resolution shallow (<500 m depth) seismic in combination with refraction tomography is used for high-fidelity imaging of true-depth stratigraphy of sedimentary formations, tectonic faults and specific structures for the improved understanding of (hydro)geology in general and as potential indicator for uranium mineralization in particular. A new-generation geophysical downhole-wireline tool with pulsed neutron generator has been developed (i) to accurately measure U grade (PFN [prompt fission neutron] method with important intool corrections for systematic influences), (ii) to determine geophysical parameters including porosity, density, macroscopic neutron cross section (clay content) and deduced permeability, and (iii) to log the mineral composition (based on element-specific gamma ray spectroscopy applied to natural gamma rays as well as gamma rays from inelastic neutron scattering, thermal-neutron capture and neutron activation) – all by one tool. This new data - together with conventional geophysical and geochemical information – provides an excellent aid to the assessment of ISR feasibility, the design of wellfields and planning of wellfield operation. A new kinetic leaching model (reactive transport) has been specifically adjusted to acidic leaching conditions considering kinetic rates of the main neutralizing and redox reactions as function of both pH and oxidation potential (balance of e- acceptor species). It is used as an effective tool for predicting wellfield recovery curves, estimating chemicals’ consumption and optimizing leaching chemistry (i.e. dosage of chemicals to injection lixiviant) in dependence on mineralogical conditions (abundance of main reactants). (author)

Bioremediation case study: Fuel-contaminated soil cleanup in the Marshall Islands

International Nuclear Information System (INIS)

Machanoff, R.

1992-01-01

Using microbes to degrade fuels in contaminated soils is becoming increasingly more attractive as an approach to environmental restoration. Removing contamination by traditional methods is costly, does not always eliminate the problem, and often just moves it somewhere else. Biodegradation of contaminants can often be accomplished in situ, resulting in the actual destruction of the contaminants by microbial conversion to harmless by-products. Bioremediation is not applicable to all forms of environmental contamination but has been demonstrated to be particularly effective on petroleum hydrocarbon based fuels. Bioremediation can offer a cost-effective means for site cleanup, particularly where challenging logistical considerations have to be factored into cleanup projects. Logistical considerations have made bioremediation the method of choice for the decontamination of fuel-containing soils on Kwajalein Island, Republic of the Marshall Islands. Kwajalein is located more than 2,100 miles west of Hawaii in the southernmost part of the North Pacific. The site of a major missile range of the Strategic Defense Command (SDC), Kwajalein has been the center of US defense activities for almost 50 years. The island is part of a typical coral atoll and is only 2.5 miles long and 0.5 miles wide. Mission-related activities over the past 5 decades have resulted in about 10% of the island being contaminated with diesel, gasoline, and jet fuels. SDC has executed an agreement with the Department of Energy for the Hazardous Waste Remedial Actions Program (HAZWRAP), a division of Martin Marietta Energy Systems, Inc., to assist the US Army Kwajalein Atoll (USAKA) in the management of the Base restoration activities on Kwajalein Atoll. HAZWRAP initiated sampling and feasibility studies to determine whether bioremediation was a viable choice for site cleanup at USAKA

Advances in speed and performance of on-site bioremediation

International Nuclear Information System (INIS)

Shearon, M.S.; Autry, A.R.; Archer, B.

1991-01-01

SafeSoil is a proprietary additive and ex-situ treatment process which mediates and enhances biodegradation of environmental pollutants. The additive itself contains natural surfactants, organic and inorganic nutrients, and enzymes (primarily oxygenases). The treatment is an ex-situ process involving excavation and stockpiling of contaminated soil, mixing of the excavated soil with the authors proprietary additive in a mixer, and then the placement of the treated soil in curing piles, during which time biodegradation is actively occurring. SafeSoil was proven effective at treating approximately 35,000 cubic yards of soil contaminated with gasoline, diesel fuel, kerosene, motor oil, and transmission fluid to below specified action levels (50 ppm for TFH, and five ppm for total BTEX) in a full-scale remedial action for the channel Gateway Development project at Marina del Rey, California, within 15 days for 70 to 75% of the soil mass treated. More time was required for successful bioremediation of some of the more recalcitrant (persistent) contaminants, principally longer chain aliphatic hydrocarbons

Solubility measurement of uranium in uranium-contaminated soils

International Nuclear Information System (INIS)

Lee, S.Y.; Elless, M.; Hoffman, F.

1993-08-01

A short-term equilibration study involving two uranium-contaminated soils at the Fernald site was conducted as part of the In Situ Remediation Integrated Program. The goal of this study is to predict the behavior of uranium during on-site remediation of these soils. Geochemical modeling was performed on the aqueous species dissolved from these soils following the equilibration study to predict the on-site uranium leaching and transport processes. The soluble levels of total uranium, calcium, magnesium, and carbonate increased continually for the first four weeks. After the first four weeks, these components either reached a steady-state equilibrium or continued linearity throughout the study. Aluminum, potassium, and iron, reached a steady-state concentration within three days. Silica levels approximated the predicted solubility of quartz throughout the study. A much higher level of dissolved uranium was observed in the soil contaminated from spillage of uranium-laden solvents and process effluents than in the soil contaminated from settling of airborne uranium particles ejected from the nearby incinerator. The high levels observed for soluble calcium, magnesium, and bicarbonate are probably the result of magnesium and/or calcium carbonate minerals dissolving in these soils. Geochemical modeling confirms that the uranyl-carbonate complexes are the most stable and dominant in these solutions. The use of carbonate minerals on these soils for erosion control and road construction activities contributes to the leaching of uranium from contaminated soil particles. Dissolved carbonates promote uranium solubility, forming highly mobile anionic species. Mobile uranium species are contaminating the groundwater underlying these soils. The development of a site-specific remediation technology is urgently needed for the FEMP site

Remotely operated facility for in situ solidification of fissile uranium

International Nuclear Information System (INIS)

McGinnis, C.P.; Collins, E.D.; Patton, B.D.

1986-01-01

A heavily shielded, remotely operated facility, located within the Radiochemical processing Plant at Oak Ridge National Laboratory (ORNL), has been designed and is being operated to convert approx.1000 kg of fissile uranium (containing approx.75% 235 U, approx.10% 233 U, and approx.140 ppM 232 U) from a nitrate solution (130 g of uranium per L) to a solid oxide form. This project, the Consolidated Edison Uranium Solidification Program (CEUSP), is being carried out in order to prepare a stable uranium form for longterm storage. This paper describes the solidification process selected, the equipment and facilities required, the experimental work performed to ensure successful operation, some problems that were solved, and the initial operations

Profiling microbial community structures across six large oilfields in China and the potential role of dominant microorganisms in bioremediation.

Science.gov (United States)

Sun, Weimin; Li, Jiwei; Jiang, Lei; Sun, Zhilei; Fu, Meiyan; Peng, Xiaotong

2015-10-01

Successful bioremediation of oil pollution is based on a comprehensive understanding of the in situ physicochemical conditions and indigenous microbial communities as well as the interaction between microorganisms and geochemical variables. Nineteen oil-contaminated soil samples and five uncontaminated controls were taken from six major oilfields across different geoclimatic regions in China to investigate the spatial distribution of the microbial ecosystem. Microbial community analysis revealed remarkable variation in microbial diversity between oil-contaminated soils taken from different oilfields. Canonical correspondence analysis (CCA) further demonstrated that a suite of in situ geochemical parameters, including soil moisture and sulfate concentrations, were among the factors that influenced the overall microbial community structure and composition. Phylogenetic analysis indicated that the vast majority of sequences were related to the genera Arthrobacter, Dietzia, Pseudomonas, Rhodococcus, and Marinobacter, many of which contain known oil-degrading or oil-emulsifying species. Remarkably, a number of archaeal genera including Halalkalicoccus, Natronomonas, Haloterrigena, and Natrinema were found in relatively high abundance in some of the oil-contaminated soil samples, indicating that these Euryarchaeota may play an important ecological role in some oil-contaminated soils. This study offers a direct and reliable reference of the diversity of the microbial community in various oil-contaminated soils and may influence strategies for in situ bioremediation of oil pollution.

Treatability testing of intrinsic bioremediation, biostimulation, and bioaugmentation of diesel-oil contaminated soil at 5 degrees C

International Nuclear Information System (INIS)

Wilson, J. J.

1997-01-01

The likely success of in-situ bioremediation on diesel-contaminated soil was studied at 5 degrees C under four conditions of soil amendments. The four conditions were: (1) intrinsic bioremediation where the soil received only water, (2) biostimulation with one application of slow-release fertilizer, (3) bioaugmentation with one application of fertilizer and a cold-adapted hydrocarbon-degrading bacterial culture, and (4) surfactant enhanced bioavailability, where the soil received one application of fertilizer and treatment with a biodegradable surfactant solution. All tests showed significant reduction in diesel range under aerobic conditions after a 40-day incubation. The intrinsic control (No.1) was least effective, with 66 per cent of extractable hydrocarbons (TEH) at 5 degrees C. The biostimulated soil (No.2) was most effective, allowing a reduction in TEH of 86 per cent. The bioaugmented soil and surfactant treated soil allowed TEH reduction of about 75 per cent. Based on these results, biostimulation with slow-release fertilizer will be implemented as the most cost-effective means of bioremediation, combined with appropriate monitoring of results. 2 refs., 3 tabs., 4 figs

Assessing TCE source bioremediation by geostatistical analysis of a flux fence.

Science.gov (United States)

Cai, Zuansi; Wilson, Ryan D; Lerner, David N

2012-01-01

Mass discharge across transect planes is increasingly used as a metric for performance assessment of in situ groundwater remediation systems. Mass discharge estimates using concentrations measured in multilevel transects are often made by assuming a uniform flow field, and uncertainty contributions from spatial concentration and flow field variability are often overlooked. We extend our recently developed geostatistical approach to estimate mass discharge using transect data of concentration and hydraulic conductivity, so accounting for the spatial variability of both datasets. The magnitude and uncertainty of mass discharge were quantified by conditional simulation. An important benefit of the approach is that uncertainty is quantified as an integral part of the mass discharge estimate. We use this approach for performance assessment of a bioremediation experiment of a trichloroethene (TCE) source zone. Analyses of dissolved parent and daughter compounds demonstrated that the engineered bioremediation has elevated the degradation rate of TCE, resulting in a two-thirds reduction in the TCE mass discharge from the source zone. The biologically enhanced dissolution of TCE was not significant (~5%), and was less than expected. However, the discharges of the daughter products cis-1,2, dichloroethene (cDCE) and vinyl chloride (VC) increased, probably because of the rapid transformation of TCE from the source zone to the measurement transect. This suggests that enhancing the biodegradation of cDCE and VC will be crucial to successful engineered bioremediation of TCE source zones. © 2012, The Author(s). Ground Water © 2012, National Ground Water Association.

Bioremediation of petroleum contaminated soil

International Nuclear Information System (INIS)

Autry, A.R.; Ellis, G.M.

1992-01-01

This paper reports on bioremediation, which offers a cost-competitive, effective remediation alternative for soil contaminated with petroleum products. These technologies involve using microorganisms to biologically degrade organic constituents in contaminated soil. All bioremediation applications must mitigate various environmental rate limiting factors so that the biodegradation rates for petroleum hydrocarbons are optimized in field-relevant situations. Traditional bioremediation applications include landfarming, bioreactors, and composting. A more recent bioremediation application that has proven successful involves excavation of contaminated soil. The process involves the placement of the soils into a powerscreen, where it is screened to remove rocks and larger debris. The screened soil is then conveyed to a ribbon blender, where it is mixed in batch with nutrient solution containing nitrogen, phosphorus, water, and surfactants. Each mixed soil batch is then placed in a curing pile, where it remains undisturbed for the remainder of the treatment process, during which time biodegradation by naturally occurring microorganisms, utilizing biochemical pathways mediated by enzymes, will occur

Bioremediation--Why doesn't it work sometimes?

International Nuclear Information System (INIS)

Block, R.; Stroo, H.; Swett, G.H.

1993-01-01

Biological treatment has rapidly become the technology of choice for remediation of soils contaminated by petroleum constituents. Since the mid-1980s, bioremediation has been used at more than 100 locations to cost-effectively remediate hundreds of thousands of cubic yards of contaminated soil. However, despite the excellent track record of bioremediation, during the past few years bioremediation was not successful at several sites. The same type of contaminated soils has been treated successfully at numerous other sites. The treatment process was the same, but bioremediation was not effective. Testing identified other sites where bioremediation was unsuccessful for remediating petroleum constituents, and the factors that contributed to the failures were explored in greater depth. This article outlines a quick and inexpensive screening technique that allows one to determine whether bioremediation is practical and also provides an assessment of the time and cost factors. It involves four steps: (1) Site study; (2) Regulatory analysis; (3) Biological screening; (4) Treatability testing. The methodology can be reduced to a set of decision trees to simplify the screening process

Fungi outcompete bacteria under increased uranium concentration in culture media

International Nuclear Information System (INIS)

Mumtaz, Saqib; Streten-Joyce, Claire; Parry, David L.; McGuinness, Keith A.; Lu, Ping; Gibb, Karen S.

2013-01-01

As a key part of water management at the Ranger Uranium Mine (Northern Territory, Australia), stockpile (ore and waste) runoff water was applied to natural woodland on the mine lease in accordance with regulatory requirements. Consequently, the soil in these Land Application Areas (LAAs) presents a range of uranium concentrations. Soil samples were collected from LAAs with different concentrations of uranium and extracts were plated onto LB media containing no (0 ppm), low (3 ppm), medium (250 ppm), high (600 ppm) and very high (1500 ppm) uranium concentrations. These concentrations were similar to the range of measured uranium concentrations in the LAAs soils. Bacteria grew on all plates except for the very high uranium concentrations, where only fungi were recovered. Identifications based on bacterial 16S rRNA sequence analysis showed that the dominant cultivable bacteria belonged to the genus Bacillus. Members of the genera Paenibacillus, Lysinibacillus, Klebsiella, Microbacterium and Chryseobacterium were also isolated from the LAAs soil samples. Fungi were identified by sequence analysis of the intergenic spacer region, and members of the genera Aspergillus, Cryptococcus, Penicillium and Curvularia were dominant on plates with very high uranium concentrations. Members of the Paecilomyces and Alternaria were also present but in lower numbers. These findings indicate that fungi can tolerate very high concentrations of uranium and are more resistant than bacteria. Bacteria and fungi isolated at the Ranger LAAs from soils with high concentrations of uranium may have uranium binding capability and hence the potential for uranium bioremediation. -- Highlights: ► Fungi outcompete bacteria under increased uranium concentration in culture media. ► Soil microorganisms isolated from the Ranger Land Application Areas (LAAs) were resistant to uranium. ► Bacillus was the most abundant cultivable genus retrieved from the Ranger LAAs soils. ► Uranium in LAAs soils is

Uranium exploration, mining and ore enrichment techniques

International Nuclear Information System (INIS)

Fuchs, H.D.; Wentzlau, D.

1985-01-01

The paper describes the different types of uranium deposits and their importance. It is shown that during the present depressed uranium market situation, mainly high grade deposits such as unconformity-related deposits can be mined economically. The different successive exploration steps are outlined including methods used for uranium. Uranium mining does not greatly differ from normal mining, but the uranium metallurgy needs its own specialized but already classic technology. Only a relative small amount of uranium can be expected from projects where uranium is produced by in situ leach methods or by extraction from phosphoric acid. A short summary of investment costs and operating costs is given for an average uranium mine. The last chapter deals with the definition of different reserve categories and outlines the uranium reserves of the western world including the uranium production (1983) and the expected uranium production capacity for 1985 and 1990. (orig.) [de

Uranium production and the environment in Kazakhstan

International Nuclear Information System (INIS)

Fyodorov, G.V.

2002-01-01

The production of uranium from open-pit and underground mines in Kazakhstan has terminated. Currently, uranium is extracted in Kazakhstan only by the In Situ Leaching (ISL) method. This method has a number of economical and ecological advantages. During a short period in the 70s-80s, Kazakhstan created a firm basis for developing uranium extraction by the ISL method. Now more than half of the world's uranium reserves amenable to the ISL method are located in Kazakhstan. By 2005, a significant increase in uranium production is planned. Thereby, Kazakhstan has the ability to grow into a world leader in uranium extraction through a lower cost and low environmental impact operations using the ISL method. (author)

In situ diesel fuel bioremediation: A case history

International Nuclear Information System (INIS)

Rhodes, D.K.; Burke, G.K.; Smith, N.; Clark, D.

1995-01-01

As a result of a ruptured fuel line, the study site had diesel fuel soil contamination and free product more than 2 ft (0.75 m) thick on the groundwater surface. Diesel fuel, which is composed of a high percentage of nonvolatile compounds, has proven difficult to remediate using conventional extraction remediation techniques. A number of remedial alternatives were reviewed, and the patented in situ biodegradation BioSparge SM technology was selected for the site and performed under license by a specialty contractor. BioSparge SM is a field-proven closed-loop (no vapor emissions) system that supplies a continuous, steady supply of oxygen, moisture, and additional heat to enhance microorganism activity. The system injects an enriched airstream beneath the groundwater surface elevation and/or within the contaminant plume and removes residual vapors from vadose zone soil within and above the contaminant plume. The technology has no air discharge, which is critical in areas where strict air discharge regulations apply. The focus of this paper is the viability of in situ biodegradation as an effective remediation alternative for reducing nonvolatile petroleum products

Bioremediation of contaminated sites

International Nuclear Information System (INIS)

Schneider, C.

1996-01-01

By volatilizing aromatic compounds through aeration, landfarming is a recognized approach to the bioremediation of hydrocarbon contaminated soil. With this method, the soil is cultivated and aided with fertilizer amendment to provide a nutrient source for the microbial population involved in the degradation of hydrocarbons. The effectiveness of bioremediation will depend on several factors, including topographic features, soil properties, and biochemistry. Since bioremediation is inhibited by anaerobic conditions, sites that are sloped or have trenches to collect runoff water are preferable. As for soil properties, the percentage of sand should not be too high, but aeration is essential to avoid anaerobic conditions. Addition of straw is generally beneficial, and fertilizers with nitrogen, phosphorous and potassium will help degrading hydrocarbons. Temperature, pH, and salt content are also important factors since they facilitate microbial activity. 3 refs

Study in situ of the natural uranium, 60 Co and 137 Cs bioaccumulation factor in fish (Cyprinus carpio)

International Nuclear Information System (INIS)

Todoran, A.; Toma, A.; Dulama, C.; Horhoianu, V.; Hirica, O.; Patriche, N.; Tenciu, M.; Talpes, M.; Cristea, V.

2006-01-01

The paper presents the results of the 'in situ' research, aiming to determine the bioaccumulation factor of natural uranium, 60 Co and 137 Cs in fish (Cyprinus carpio) - the find link in aquatic ecosystems. The work performed is a part of a radioecological study achieved in the experimental pool of S.C.N. Pitesti. The objective of the research was to evaluate the release of the radioactive materials in the environment as well as to establish the transfer mechanisms of the radionuclides in the trophic chains from the aquatic ecosystem. (authors)