Psychophysical basis for maximum pushing and pulling forces: A review and recommendations.

Science.gov (United States)

Garg, Arun; Waters, Thomas; Kapellusch, Jay; Karwowski, Waldemar

2014-03-01

The objective of this paper was to perform a comprehensive review of psychophysically determined maximum acceptable pushing and pulling forces. Factors affecting pushing and pulling forces are identified and discussed. Recent studies show a significant decrease (compared to previous studies) in maximum acceptable forces for males but not for females when pushing and pulling on a treadmill. A comparison of pushing and pulling forces measured using a high inertia cart with those measured on a treadmill shows that the pushing and pulling forces using high inertia cart are higher for males but are about the same for females. It is concluded that the recommendations of Snook and Ciriello (1991) for pushing and pulling forces are still valid and provide reasonable recommendations for ergonomics practitioners. Regression equations as a function of handle height, frequency of exertion and pushing/pulling distance are provided to estimate maximum initial and sustained forces for pushing and pulling acceptable to 75% male and female workers. At present it is not clear whether pushing or pulling should be favored. Similarly, it is not clear what handle heights would be optimal for pushing and pulling. Epidemiological studies are needed to determine relationships between psychophysically determined maximum acceptable pushing and pulling forces and risk of musculoskeletal injuries, in particular to low back and shoulders.

Pushing and pulling in relation to musculoskeletal complaints

NARCIS (Netherlands)

Hoozemans, M. J M; Van Der Beek, Allard J.; Frings-Dresen, M. H. W.

2000-01-01

The first cross-sectional analyses are presented of a longitudinal study regarding the relationship between pushing and pulling and musculoskeletal disorders. Workers exposed to pushing and pulling and workers who had administrative tasks received a questionnaire. A significant association between

KOMPARASI SISTEM MANUFAKTUR PUSH DAN PULL MELALUI PENDEKATAN SIMULASI

Directory of Open Access Journals (Sweden)

Eric Wibisono

2004-01-01

Full Text Available Manufacturing systems that are often classified as push and pull often invite question: "How far do the differences between those two systems exist?" Many researches have been carried out but succinct answer to the above question is always difficult to reach. The difficulty roots from the variety of definition of the push and pull systems itself and also from the variety of complexity of a manufacturing system. This paper attempts to study the differences in performance between push and pull systems in a relatively simple model that consists of 4 serial processors with buffers located between these processors. Variations being modelled is on the setting of the system's load (high and low and the buffer size with performance being measured include machine utilization, number of outputs and mean flow time of jobs. The approach used is simulation using ProModel software as the tool. From the experiments it can be derived that buffer size turns out to be a very critical factor in system performance. Moreover, it is also proved that when the buffer size is large, push and pull systems do not differ significantly. Abstract in Bahasa Indonesia : Sistem manufaktur yang umumnya dikategorikan menjadi sistem push dan pull sering mengundang pertanyaan: "Seberapa jauh perbedaan dari kedua sistem tersebut ada?" Banyak penelitian telah dilakukan namun jawaban yang lugas atas pertanyaan tersebut sulit diperoleh. Kesulitan ini umumnya berakar dari beragamnya definisi sistem push dan pull itu sendiri serta variasi dari kompleksitas suatu sistem manufaktur. Makalah ini mencoba melihat perbedaan antara kinerja sistem push dan pull dalam suatu model sederhana yang terdiri dari 4 prosesor serial dengan buffer yang diletakkan di antara masing-masing prosesor tersebut. Variasi yang dilakukan adalah pada setting beban kerja sistem (padat dan ringan dan ukuran buffer dengan kinerja yang diukur adalah utilisasi mesin, jumlah output dan rata-rata waktu tinggal job

Evaluation of sulfate reduction at experimentally induced mixing interfaces using small-scale push-pull tests in an aquifer-wetland system

International Nuclear Information System (INIS)

Kneeshaw, Tara A.; McGuire, Jennifer T.; Smith, Erik W.; Cozzarelli, Isabelle M.

2007-01-01

This paper presents small-scale push-pull tests designed to evaluate the kinetic controls on SO 4 2- reduction in situ at mixing interfaces between a wetland and aquifer impacted by landfill leachate at the Norman Landfill research site, Norman, OK. Quantifying the rates of redox reactions initiated at interfaces is of great interest because interfaces have been shown to be zones of increased biogeochemical transformations and thus may play an important role in natural attenuation. To mimic the aquifer-wetland interface and evaluate reaction rates, SO 4 2- -rich anaerobic aquifer water (∼100mg/LSO 4 2- ) was introduced into SO 4 2- -depleted wetland porewater via push-pull tests. Results showed SO 4 2- reduction was stimulated by the mixing of these waters and first-order rate coefficients were comparable to those measured in other push-pull studies. However, rate data were complex involving either multiple first-order rate coefficients or a more complex rate order. In addition, a lag phase was observed prior to SO 4 2- reduction that persisted until the mixing interface between test solution and native water was recovered, irrespective of temporal and spatial constraints. The lag phase was not eliminated by the addition of electron donor (acetate) to the injected test solution. Subsequent push-pull tests designed to elucidate the nature of the lag phase support the importance of the mixing interface in controlling terminal electron accepting processes. These data suggest redox reactions may occur rapidly at the mixing interface between injected and native waters but not in the injected bulk water mass. Under these circumstances, push-pull test data should be evaluated to ensure the apparent rate is actually a function of time and that complexities in rate data be considered

Casing pull tests for directionally drilled environmental wells

International Nuclear Information System (INIS)

Staller, G.E.; Wemple, R.P.; Layne, R.R.

1994-11-01

A series of tests to evaluate several types of environmental well casings have been conducted by Sandia National Laboratories (SNL) and it's industrial partner, The Charles Machine Works, Inc. (CMW). A test bed was constructed at the CMW test range to model a typical shallow, horizontal, directionally drilled wellbore. Four different types of casings were pulled through this test bed. The loads required to pull the casings through the test bed and the condition of the casing material were documented during the pulling operations. An additional test was conducted to make a comparison of test bed vs actual wellbore casing pull loads. A directionally drilled well was emplaced by CMW to closely match the test bed. An instrumented casing was installed in the well and the pull loads recorded. The completed tests are reviewed and the results reported

Casing pull tests for directionally drilled environmental wells

Energy Technology Data Exchange (ETDEWEB)

Staller, G.E.; Wemple, R.P. [Sandia National Labs., Albuquerque, NM (United States); Layne, R.R. [Charles Machine Works, Inc., Perry, OK (United States)

1994-11-01

A series of tests to evaluate several types of environmental well casings have been conducted by Sandia National Laboratories (SNL) and it`s industrial partner, The Charles Machine Works, Inc. (CMW). A test bed was constructed at the CMW test range to model a typical shallow, horizontal, directionally drilled wellbore. Four different types of casings were pulled through this test bed. The loads required to pull the casings through the test bed and the condition of the casing material were documented during the pulling operations. An additional test was conducted to make a comparison of test bed vs actual wellbore casing pull loads. A directionally drilled well was emplaced by CMW to closely match the test bed. An instrumented casing was installed in the well and the pull loads recorded. The completed tests are reviewed and the results reported.

Pushing, pulling and manoeuvring an industrial cart: a psychophysiological study.

Science.gov (United States)

Giagloglou, Evanthia; Radenkovic, Milan; Brankovic, Sasa; Antoniou, Panagiotis; Zivanovic-Macuzic, Ivana

2017-09-18

One of the most frequent manual occupational tasks involves the pushing and pulling of a cart. Although several studies have associated health risks with pushing and pulling, the effects are not clear since occupational tasks have social, cognitive and physical components. The present work investigates a real case of a pushing and pulling occupational task from a manufacturing company. The study initially characterizes the case in accordance with Standard No. ISO 11228-2:2007 as low risk. An experiment with 14 individuals during three modalities of pushing and pulling was performed in order to further investigate the task with the application of electrophysiology. At the end, a simple questionnaire was given. The results show electrophysiological differences among the three modalities of pushing and pulling, with a major difference between action with no load and fully loaded with a full range of motions on the cart to handle.

Push-pull alkenes: structure and p-electron distribution

Directory of Open Access Journals (Sweden)

ERICH KLEINPETER

2006-01-01

Full Text Available Push-pull alkenes are substituted alkenes with one or two electron-donating substituents on one end of C=C double bond and with one or two electron-accepting substituents at the other end. Allowance for p-electron delocalization leads to the central C=C double bond becoming ever more polarized and with rising push-pull character, the p-bond order of this double bond is reduced and, conversely, the corresponding p-bond orders of the C–Don and C–Acc bonds are accordingly increased. This push-pull effect is of decisive influence on both the dynamic behavior and the chemical reactivity of this class of compounds and thus it is of considerable interest to both determine and to quantify the inherent push-pull effect. Previously, the barriers to rotation about the C=C, C–Don and/or C–Acc partial double bonds (DG±, as determined by dynamic NMR spectroscopy or the 13C chemical shift difference of the polarized C=C partial double bond (DdC=C were employed for this purpose. However, these parameters can have serious limitations, viz. the barriers can be immeasurable on the NMR timescale (either by being too high or too low; heavily-biased conformers are present, etc. or DdC=C behaves in a non-additive manner with respect to the combination of the four substituents. Hence, a general parameter to quantify the push-pull effect is not yet available. Ab initio MO calculations on a collection of compounds, together with NBO analysis, provided valuable information on the structure, bond energies, electron occupancies and bonding/antibonding interactions. In addition to DG±C=C (either experimentally determined or theoretically calculated and DdC=C, the bond length of the C=C partial double bond was also examined and it proved to be a reliable parameter to quantify the push-pull effect. Equally so, the quotient of the occupation numbers of the antibonding andbonding p orbitals of the central C=C partial double bond ( p*C=C/ pC=C could also be employed for

Biomechanical study of the final push-pull in archery.

Science.gov (United States)

Leroyer, P; Van Hoecke, J; Helal, J N

1993-02-01

The purpose of this study was to analyse archery performance among eight archers of different abilities by means of displacement pull-hand measurements during the final push-pull phase of the shoot. The archers showed an irregular displacement negatively related to their technical level. Displacement signal analysis showed high power levels in both the 0-5 Hz and 8-12 Hz ranges. The latter peak corresponds to electromyographic tremor observed during a prolonged push-pull effort. The results are discussed in relation to some potentially helpful training procedures such as biofeedback and strength conditioning.

Force direction in pushing and pulling and Musculo-Skeletal load

NARCIS (Netherlands)

Looze, M.P. de; Kuijer, P.P.F.M.

1999-01-01

In pushing and pulling wheeled objects, the effect of the exerted force on local musculo-skeletal loads depends on the direction of force exertion. Several questions about the direction of force exertion in pushing and pulling, the effects of handle height and force level on force direction, and the

Technology and trend management at the interface of technology push and market pull

DEFF Research Database (Denmark)

Maier, Maximilian; Hofmann, Maximilian; Brem, Alexander

2016-01-01

Technology push and market pull innovation strategies are playing an important role for the effective management of ideas, technologies, and trends. The coexistence of these two approaches led to many debates and the focus switched several times from putting more effort into technology push aspects...... to fostering market pull approaches in the last decades. Still, there is no in-depth exploration of the interface of technology push and market pull and only few conceptual models are dealing with the connection between technology push and market pull in particular. Therefore, this study puts an exploratory...... focus on the innovation management processes of a global outdoor manufacturer with a special emphasis on the interface between technology push and market pull. From the case findings and our literature we conceptualise a non-linear innovation model that systematically integrates market pull...

Field evaluation of a push-pull system to reduce malaria transmission.

Directory of Open Access Journals (Sweden)

David J Menger

Full Text Available Malaria continues to place a disease burden on millions of people throughout the tropics, especially in sub-Saharan Africa. Although efforts to control mosquito populations and reduce human-vector contact, such as long-lasting insecticidal nets and indoor residual spraying, have led to significant decreases in malaria incidence, further progress is now threatened by the widespread development of physiological and behavioural insecticide-resistance as well as changes in the composition of vector populations. A mosquito-directed push-pull system based on the simultaneous use of attractive and repellent volatiles offers a complementary tool to existing vector-control methods. In this study, the combination of a trap baited with a five-compound attractant and a strip of net-fabric impregnated with micro-encapsulated repellent and placed in the eaves of houses, was tested in a malaria-endemic village in western Kenya. Using the repellent delta-undecalactone, mosquito house entry was reduced by more than 50%, while the traps caught high numbers of outdoor flying mosquitoes. Model simulations predict that, assuming area-wide coverage, the addition of such a push-pull system to existing prevention efforts will result in up to 20-fold reductions in the entomological inoculation rate. Reductions of such magnitude are also predicted when mosquitoes exhibit a high resistance against insecticides. We conclude that a push-pull system based on non-toxic volatiles provides an important addition to existing strategies for malaria prevention.

Using Metaheuristic and Fuzzy System for the Optimization of Material Pull in a Push-Pull Flow Logistics Network

Directory of Open Access Journals (Sweden)

Afshin Mehrsai

2013-01-01

Full Text Available Alternative material flow strategies in logistics networks have crucial influences on the overall performance of the networks. Material flows can follow push, pull, or hybrid systems. To get the advantages of both push and pull flows in networks, the decoupling-point strategy is used as coordination mean. At this point, material pull has to get optimized concerning customer orders against pushed replenishment-rates. To compensate the ambiguity and uncertainty of both dynamic flows, fuzzy set theory can practically be applied. This paper has conceptual and mathematical parts to explain the performance of the push-pull flow strategy in a supply network and to give a novel solution for optimizing the pull side employing Conwip system. Alternative numbers of pallets and their lot-sizes circulating in the assembly system are getting optimized in accordance with a multi-objective problem; employing a hybrid approach out of meta-heuristics (genetic algorithm and simulated annealing and fuzzy system. Two main fuzzy sets as triangular and trapezoidal are applied in this technique for estimating ill-defined waiting times. The configured technique leads to smoother flows between push and pull sides in complex networks. A discrete-event simulation model is developed to analyze this thesis in an exemplary logistics network with dynamics.

Push-pull optical pumping of pure superposition states

International Nuclear Information System (INIS)

Jau, Y.-Y.; Miron, E.; Post, A.B.; Kuzma, N.N.; Happer, W.

2004-01-01

A new optical pumping method, 'push-pull pumping', can produce very nearly pure, coherent superposition states between the initial and the final sublevels of the important field-independent 0-0 clock resonance of alkali-metal atoms. The key requirement for push-pull pumping is the use of D1 resonant light which alternates between left and right circular polarization at the Bohr frequency of the state. The new pumping method works for a wide range of conditions, including atomic beams with almost no collisions, and atoms in buffer gases with pressures of many atmospheres

Push and pull strategies: applications for health care marketing.

Science.gov (United States)

Kingsley, B R

1987-08-01

As health care markets mature and expand, strategies available in other industries become useful. This article examines how traditional push-pull strategies apply to health care. Marketers using a push strategy recognize that the sale of their services or goods is dependent upon the endorsement of a middleman and promote their product through the middleman. Those using a pull strategy market directly to the consumer. In this article, the author outlines the advantages and disadvantages of using each strategy.

Positioning of microtubule organizing centers by cortical pushing and pulling forces

International Nuclear Information System (INIS)

Pavin, Nenad; Ma Rui; Jülicher, Frank; Laan, Liedewij; Dogterom, Marileen

2012-01-01

Positioning of microtubule (MT) organizing centers with respect to the confining geometry of cells depends on pushing and/or pulling forces generated by MTs that interact with the cell cortex (Dogterom et al 2005 Curr. Opin. Cell Biol. 17 67–74). How, in living cells, these forces lead to proper positioning is still largely an open question. Recently, it was shown by in vitro experiments using artificial microchambers that in a square geometry, MT asters center more reliably by a combination of pulling and pushing forces than by pushing forces alone (Laan et al 2012a Cell 148 502–14). These findings were explained by a physical description of aster mechanics that includes slipping of pushing MT ends along chamber boundaries. In this paper, we extend that theoretical work by studying the influence of the shape of the confining geometry on the positioning process. We find that pushing and pulling forces can have centering or off-centering behavior in different geometries. Pushing forces center in a one-dimensional and a square geometry, but lead to off-centering in a circle if slipping is sufficiently pronounced. Pulling forces, however, do not center in a one-dimensional geometry, but improve centering in a circle and a square. In an elongated stadium geometry, positioning along the short axis depends mainly on pulling forces, while positioning along the long axis depends mainly on pushing forces. Our theoretical results suggest that different positioning strategies could be used by different cell types. (paper)

Push-pull test: a method of evaluating formation adsorption parameters for predicting the environmental effects on in situ coal gasification and uranium recovery

International Nuclear Information System (INIS)

Drever, J.I.; McKee, C.R.

1980-11-01

The push-pull test, which is a simple injection and pumping sequence of groundwater spiked with solutes of interest, is presented as a method of determining the adsorption characteristics of a formation. Adsorption properties are necessary to predict restoration from both in situ coal gasification and in situ uranium extraction. The major problems in applying laboratory measurements to the field concern scaling the effect of particle size and obtaining representative samples. Laboratory measurements are conducted on gram to kilogram scale samples, whereas the push-pull test evaluates a sample weighing approximately 130 to 1000 metric tons, depending on volume injected and porosity. The problem in translating laboratory results to the field appear to be less severe for sedimentary uranium bodies than for coal. Laboratory measurements are useful in delineating ranges in adsorption properties and in planning the field experiment. Two field push-pull tests were conducted on uranium formations in Wyoming. Adsorption properties estimated from these tests on the basis of a simple cell model were compared to the laboratory values. In the first case, excellent agreement was observed between the values estimated from the field test and the values measured in the laboratory. In the second case, the value for K/sub d/ determined in the laboratory was five times higher than the field value. It is recommended that push-pull tests be conducted on coal formations being considered for in situ gasification in view of the great uncertainty in extrapolating laboratory adsorption properties to the field

Push-Pull Ventilation in a Painting Shop for Large Steel Constructions

DEFF Research Database (Denmark)

Svidt, Kjeld; Heiselberg, Per

This paper describes the analysis of a push-pull ventilation system for a painting shop that is used for painting steel chimneys and windmill towers.......This paper describes the analysis of a push-pull ventilation system for a painting shop that is used for painting steel chimneys and windmill towers....

Push-Pull Effects of Three Plant Secondary Metabolites on Oviposition of the Potato Tuber Moth, Phthorimaea operculella

Science.gov (United States)

Ma, Y.F.; Xiao, C.

2013-01-01

The push-pull effects of three plant secondary metabolites, azadirachtin, eucalyptol, and heptanal, on the oviposition choices of potato tubers by the potato tuber moth, Phthorimaea operculella (Zeller) (Lepidoptera: Gelechiidae) were tested in the laboratory. Azadirachtin at concentrations from 1.5 to 12 mg/L had a significant repellent effect on oviposition. Eucalyptol at concentrations from 3 to 12 mg/L promoted oviposition. Heptanal promoted oviposition at low concentrations from 0.1875 to 3.0 mg/L but repelled it at higher concentrations from 12 to 24 mg/L. The combination of azadirachtin (12 mg/L) with eucalyptol (3.0 mg/L) resulted in a significant pushpull effect of 56.3% on oviposition. The average maximum push-pull effects occurred with the combinations of azadirachtin with heptanal (12 and 0.375 mg/L, respectively; 38.7% push-pull effect), heptanal with eucalyptol (12 and 6 mg/L, respectively; 31.4% push-pull effect), and heptanal (high concentration) with heptanal (low concentration) (12.0 and 0.375 mg/L, respectively; 25% push-pull effect). PMID:24786822

A demonstration of NIOSH push-pull ventilation criteria.

Science.gov (United States)

Klein, M K

1987-03-01

This paper summarizes the results of a study performed on an actual chrome plating tank in order to validate criteria for push-pull ventilation systems developed by Huebener and Hughes at NIOSH. Validation of the criteria was made by taking area industrial hygiene samples for hexavalent and total chrome at ten locations around the plating tank. The sampling was performed during actual production runs or while the tank was operating with a dummy load. The sampling data are summarized. The data show that the push-pull system, operating at Huebener's criteria, could control emissions to below the current standards and guidelines. Conclusions and recommendations are included.

Modelling the behaviour of the push-pull gel dosimeter

International Nuclear Information System (INIS)

Bosi, S.G.; Davies, J.B.; Gorjiara, T.; Baldock, C.

2010-01-01

Full text: Recent development of a gel dosimeter based on the radiobleaching pigment, genipin, allows development of a new 3D optically scanned gel dosimeter-the p ush-pull g el. This gel would contain two spectrally complementary pigments, one which darkens with dose and another (e.g. genipin) which bleaches. The two pigments deal separately with the high and low dose ends of the dosimeter's dynamic range. The bleaching pigment would be optimised for high sensitivity and the darkening pigment for low. Employing dual pigments, optimised independently, relaxes the need for compromise between sensitivity at low dose and accuracy at high dose. Such a gel, after exposure, would be read using two successive optical CT scans, at two different wavelengths. The reduction in sensitivity of the darkening pigment (allowed by the use of push-pull) would reduce the occurrence of regions of high optical attenuation which can generate optical CT artefacts. Simulated optical CT reconstructions of the optical density map (Fig. La) scanned at the darkening pigment wavelength of a hypothetical push-pull gel, confirms the reduction in susceptibility to artefacts. Fig. I b shows a profile through the map with no stray light added. The centre of the profile in Fig. I d shows a cupping artefact produced by 10 ppm of stray light. The similarity of Fig. Ic and b show that a 30% sensitivity reduction allowed by push-pull, renders the artefact negligible. This paper presents the results of' these simulations of a push-pull gel scanned using optical CT and also some results of experiments with genipin gel. (author)

Beyond Knut Holt's fusion model, balancing market pull and technology push

NARCIS (Netherlands)

Nagel, A.P.

2003-01-01

Should a firm rely on market pull or on technology push? Some scholars have extreme opinions on this and firms do switch emphasis on push and pull over time. Knut Holt, the first president of ISPIM, presented his so-called Fusion Model in the early 1970s to shed light onto this debate. This paper

Low-back and shoulder complaints among workers with pushing and pulling tasks

NARCIS (Netherlands)

Hoozemans, Marco J. M.; van der Beek, Allard J.; Fring-Dresen, Monique H. W.; van der Woude, Luc H. V.; van Dijk, Frank J. H.

2002-01-01

Objectives Low-back and shoulder complaints were examined in relation to self-reported and objectively assessed exposure to work-related pushing and pulling. Methods Workers from several companies (eg, nursing homes and flower auctions) with pushing and pulling tasks and, as reference, workers

Push versus pull gastrostomy in cancer patients: A single center retrospective analysis of complications and technical success rates.

Science.gov (United States)

Currie, B M; Getrajdman, G I; Covey, A M; Alago, W; Erinjeri, J P; Maybody, M; Boas, F E

2018-04-28

To compare the technical success and complication rates of push versus pull gastrostomy tubes in cancer patients, and to examine their dependence on operator experience. A retrospective review was performed of 304 cancer patients (170 men, 134 women; mean age 60.3±12.6 [SD], range: 19-102 years) referred for primary gastrostomy tube placement, 88 (29%) of whom had a previously unsuccessful attempt at percutaneous endoscopic gastrostomy (PEG) placement. Analyzed variables included method of insertion (push versus pull), indication for gastrostomy, technical success, operator experience, and procedure-related complications within 30 days of placement. Gastrostomy tubes were placed for feeding in 189 patients and palliative decompression in 115 patients. Technical success was 91%: 78% after endoscopy had previously been unsuccessful and 97% when excluding failures associated with prior endoscopy. In the first 30 days, there were 29 minor complications (17.2%) associated with push gastrostomies, and only 8 minor complications (7.5%) with pull gastrostomies (Ptechnical success rates for more versus less experienced operators. Pull gastrostomy tube placement had a lower rate of complications than push gastrostomy tube placement, especially when the indication was decompression. The technical success rate was high, even after a failed attempt at endoscopic placement. Both the rates of success and complications were independent of operator experience. Copyright © 2018 Société française de radiologie. Published by Elsevier Masson SAS. All rights reserved.

Pushing and pulling: an assessment tool for occupational health and safety practitioners.

Science.gov (United States)

Lind, Carl Mikael

2018-03-01

A tool has been developed for supporting practitioners when assessing manual pushing and pulling operations based on an initiative by two global companies in the manufacturing industry. The aim of the tool is to support occupational health and safety practitioners in risk assessment and risk management of pushing and pulling operations in the manufacturing and logistics industries. The tool is based on a nine-multiplier equation that includes a wide range of factors affecting an operator's health risk and capacity in pushing and pulling. These multipliers are based on psychophysical, physiological and biomechanical studies in combination with judgments from an expert group consisting of senior researchers and ergonomists. In order to consider usability, more than 50 occupational health and safety practitioners (e.g., ergonomists, managers, safety representatives and production personnel) participated in the development of the tool. An evaluation by 22 ergonomists supports that the push/pull tool is user friendly in general.

Assessment of a Geothermal Doublet in the Malm Aquifer Using a Push-Pull Tracer Test

Science.gov (United States)

Lafogler, Mark; Somogyi, Gabriella; Nießner, Reinhard; Baumann, Thomas

2013-04-01

Geothermal exploration of the Malm aquifer in Bavaria is highly successful. Data about the long-term operation, however, is still scarce, although detailed knowledge about the processes occurring in the aquifer is a key requirement to run geothermal facilities efficiently and economically. While there usually is a constant flow of data from the production well (temperatures, hydraulic data, hydrochemical conditions, gas composition) not even the temperatures in the immediate surrounding of the reinjection well are accessible or known. In 2011 the geothermal facility in Pullach was extended with a third geothermal well reaching into the Malm aquifer which is now used as a reinjection well. The former reinjection well was converted to a production well after 5 years of operation. This setting offers a unique opportunity to study the processes in the vicinity of a reinjection well and provides the data base to describe the hydraulic, thermal and hydrochemical performance of the reservoir. The viscosity of the reinjected cold water is increasing by 60% compared to the production well, thus one would expect an increase of the reinjection pressure as the cold water plume spreads around the reinjection well. Measurements, however, show a significant decrease of the reinjection pressure, suggesting processes in the aquifer which positively change the hydraulic properties and overcompensate the viscosity effects. Hydrochemical data and modeling indicate that a dissolution of the matrix along the flow pathways is responsible for the decreasing reinjection pressures. The change of the flow direction from reinjection to production was used to conduct a push-pull tracer test. Here, a series of fluorescent dye pulses was added to the reinjected water before the former reinjection well was shut down (push phase). These tracers included a conservative tracer (Fluorescein), surface-sensitive tracers (Eosin/Sulforhodamin B), and a NAPL-sensitive tracer (Na-Naphthionate). After

Benchtop-magnetic resonance imaging (BT-MRI) characterization of push-pull osmotic controlled release systems.

Science.gov (United States)

Malaterre, Vincent; Metz, Hendrik; Ogorka, Joerg; Gurny, Robert; Loggia, Nicoletta; Mäder, Karsten

2009-01-05

The mechanism of drug release from push-pull osmotic systems (PPOS) has been investigated by Magnetic Resonance Imaging (MRI) using a new benchtop apparatus. The signal intensity profiles of both PPOS layers were monitored non-invasively over time to characterize the hydration and swelling kinetics. The drug release performance was well-correlated to the hydration kinetics. The results show that (i) hydration and swelling critically depend on the tablet core composition, (ii) high osmotic pressure developed by the push layer may lead to bypassing the drug layer and incomplete drug release and (iii) the hydration of both the drug and the push layers needs to be properly balanced to efficiently deliver the drug. MRI is therefore a powerful tool to get insights on the drug delivery mechanism of push-pull osmotic systems, which enable a more efficient optimization of such formulations.

Positive Harris recurrence and diffusion scale analysis of a push pull queueing network

NARCIS (Netherlands)

Nazarathy, J.; Weiss, G.

2010-01-01

We consider a push pull queueing network with two servers and two types of job which are processed by the two servers in opposite order, with stochastic generally distributed processing times. This push pull network was introduced by Kopzon and Weiss, who assumed exponential processing times. It is

Simulation of push-pull inverter using wide bandgap devices

Science.gov (United States)

Al-badri, Mustafa; Matin, Mohammed A.

2016-09-01

This paper discusses the use of wide bandgap devices (SiC-MOSFET) in the design of a push-pull inverter which provides inexpensive low power dc-ac inverters. The parameters used were 1200V SiC MOSFET(C2M0040120D) made by power company ROHM. This modeling was created using parameters that were provided from a device datasheet. The spice model is provided by this company to study the effect of adding this component on push-pull inverter ordinary circuit and compared results between SiC MOSFET and silicon MOSFET (IRFP260M). The results focused on Vout and Vmos stability as well as on output power and MOSFET power loss because it is a very crucial aspect on DC-AC inverter design. These results are done using the National Instrument simulation program (Multisim 14). It was found that power loss is better in the 12 and 15 vdc inverter. The Vout in the SIC MOSFET circuit shows more stability in the high current low resistance load in comparison to the Silicon MOSFET circuit and this will improve the overall performance of the circuit.

Comparison of fluoroscopy-guided pull-type percutaneous radiological gastrostomy (pull-type-PRG) with conventional percutaneous radiological gastrostomy (push-type-PRG): clinical results in 253 patients

Energy Technology Data Exchange (ETDEWEB)

Yang, Yang; Schneider, J.; Dueber, C.; Pitton, M.B. [University Medical Center of the Johannes Gutenberg University Mainz, Department of Diagnostic and Interventional Radiology, Mainz (Germany)

2011-11-15

To analyze the clinical results and complications of fluoroscopy guided internal-external pull-type percutaneous radiological gastrostomy (pull-type-PRG) and conventional external-internal percutaneous radiological gastrostomy (push-type-PRG). A total of 253 patients underwent radiological gastrostomy between January 2002 and January 2010. Data were collected retrospectively from radiology reports, Chart review of clinical notes, procedure reports, discharge summaries and subsequent hospital visits. Statistical analysis was performed to compare the two methods for gastrostomy with respect to peri-interventional aspects and clinical results. 128 patients received the Pull-type-PRG whereas the other 125 patients were served with the Push-type-PRG. Indications for gastrostomy were similar in these two groups. The most frequent indications for the both methods were stenotic oesophageal tumors or head/neck tumors (54.7% in pull-type-PRG, 68% in push-type-PRG). Gastrostomy procedures were successful in 98.3% in pull-type-PRG compared to 92% in push-type-PRG. There was no procedure-related mortality. Compared to Push-type-PRG, the peri-interventional complication rate was significantly reduced in pull-type-PRG (14.8% versus 34.4%, P = 0.002). Compared to the external-internal push-type-PRG, the internal-external Pull-type-PRG showed a high primary success rate and a decreased incidence of peri-interventional complications. (orig.)

Comparison of fluoroscopy-guided pull-type percutaneous radiological gastrostomy (pull-type-PRG) with conventional percutaneous radiological gastrostomy (push-type-PRG): clinical results in 253 patients

International Nuclear Information System (INIS)

Yang, Yang; Schneider, J.; Dueber, C.; Pitton, M.B.

2011-01-01

To analyze the clinical results and complications of fluoroscopy guided internal-external pull-type percutaneous radiological gastrostomy (pull-type-PRG) and conventional external-internal percutaneous radiological gastrostomy (push-type-PRG). A total of 253 patients underwent radiological gastrostomy between January 2002 and January 2010. Data were collected retrospectively from radiology reports, Chart review of clinical notes, procedure reports, discharge summaries and subsequent hospital visits. Statistical analysis was performed to compare the two methods for gastrostomy with respect to peri-interventional aspects and clinical results. 128 patients received the Pull-type-PRG whereas the other 125 patients were served with the Push-type-PRG. Indications for gastrostomy were similar in these two groups. The most frequent indications for the both methods were stenotic oesophageal tumors or head/neck tumors (54.7% in pull-type-PRG, 68% in push-type-PRG). Gastrostomy procedures were successful in 98.3% in pull-type-PRG compared to 92% in push-type-PRG. There was no procedure-related mortality. Compared to Push-type-PRG, the peri-interventional complication rate was significantly reduced in pull-type-PRG (14.8% versus 34.4%, P = 0.002). Compared to the external-internal push-type-PRG, the internal-external Pull-type-PRG showed a high primary success rate and a decreased incidence of peri-interventional complications. (orig.)

Removal of Airborne Contaminants from a Surface Tank by a Push-Pull System

DEFF Research Database (Denmark)

Heiselberg, Per; Topp, Claus

Open surface tanks are used in many industrial processes, and local exhaust systems are often designed to capture and remove toxic fumes diffused from materials in the tanks prior to their escape into the workplace environment. The push-pull system seems to be the most efficient local exhaust...... system, but proper design is required to ensure health and safety of the workers and, furthermore, it is very desirable from an energy conservation point of view to determine an optimum and -an efficient design of push-pull hoods which can exhaust all contaminants with a minimum quantity of volume flow....... The paper describes and discusses different design methods and compares designed values with results from a measurement series of push-pull system efficiency....

Pulse width modulated push-pull driven parallel resonant converter with active free-wheel

Science.gov (United States)

Reass, William A.; Schrank, Louis

2004-06-22

An apparatus and method for high frequency alternating power generation to control kilowatts of supplied power in microseconds. The present invention includes a means for energy storage, push-pull switching means, control electronics, transformer means, resonant circuitry and means for excess energy recovery, all in electrical communication. A push-pull circuit works synchronously with a force commutated free-wheel transistor to provide current pulses to a transformer. A change in the conduction angle of the push-pull circuit changes the amount of energy coupled into the transformer's secondary oscillating circuit, thereby altering the induced secondary resonating voltage. At the end of each pulse, the force commutated free-wheel transistor causes residual excess energy in the primary circuit to be transmitted back to the storage capacitor for later use.

Laser pushing or pulling of absorbing airborne particles

Energy Technology Data Exchange (ETDEWEB)

Wang, Chuji, E-mail: cw175@msstate.edu; Gong, Zhiyong [Mississippi State University, Starkville, Mississippi 39759 (United States); Pan, Yong-Le; Videen, Gorden [U.S. Army Research Laboratory, 2800 Powder Mill Road, Adelphi, Maryland 20783 (United States)

2016-07-04

A single absorbing particle formed by carbon nanotubes in the size range of 10–50 μm is trapped in air by a laser trapping beam and concurrently illuminated by another laser manipulating beam. When the trapping beam is terminated, the movement of the particle controlled by the manipulating beam is investigated. We report our observations of light-controlled pushing and pulling motions. We show that the movement direction has little relationship with the particle size and manipulating beam's parameters but is dominated by the particle's orientation and morphology. With this observation, the controllable optical manipulation is now able to be generalized to arbitrary particles, including irregularly shaped absorbing particles that are shown in this work.

Causal assessment of occupational pushing or pulling and low back pain: results of a systematic review.

Science.gov (United States)

Roffey, Darren M; Wai, Eugene K; Bishop, Paul; Kwon, Brian K; Dagenais, Simon

2010-06-01

Low back pain (LBP) is a prevalent and expensive musculoskeletal condition that predominantly occurs in working-age individuals of industrialized nations. Although numerous occupational physical activities have been implicated in its etiology, determining the causation of occupational LBP still remains a challenge. To conduct a systematic review evaluating the causal relationship between occupational pushing or pulling and LBP. Systematic review of the literature. Studies reporting an association between occupational pushing or pulling and LBP. Numerical association between exposure to pushing or pulling and the presence of LBP. A systematic review was performed to identify, evaluate, and summarize the literature related to establishing a causal relationship, according to Bradford-Hill criteria for causation for occupational pushing or pulling and LBP. A search was conducted using Medline, EMBASE, CINAHL, Cochrane Library, and OSH-ROM, gray literature, hand-searching occupational health journals, reference lists of included studies, and expert knowledge. Methodological quality was assessed using a modified Newcastle-Ottawa Scale. This search yielded 2,766 citations. Thirteen studies met the inclusion criteria. Eight were high-quality studies and five were low-quality studies. There was conflicting evidence with one high-quality study demonstrating a positive association between occupational pushing or pulling and LBP and five studies showing no relationship. One study reported a nonstatistically significant dose-response trend, four studies discussed temporality of which one indicated a positive finding, two studies discussed the biological plausibility of a causal link between occupational pushing or pulling and LBP, and no evidence was uncovered to assess the experiment criterion. A qualitative summary of existing studies was not able to find any high-quality studies that fully satisfied any of the Bradford-Hill causation criteria for occupational pushing or

Determinants and magnitudes of manual force strengths and joint moments during two-handed standing maximal horizontal pushing and pulling.

Science.gov (United States)

Chow, Amy Y; Dickerson, Clark R

2016-04-01

Pushing and pulling are common occupational exertions that are increasingly associated with musculoskeletal complaints. This study focuses on the sensitivity of shoulder capacity to gender, handle height, exertion type (push or pull) and handle orientation for these tasks. All factors except for handle orientation influenced unilateral and total manual force strength (p pushing and pulling tasks for a diverse population. Practitioner Summary: pushing and pulling comprise nearly half of all manual materials handling tasks. Practitioners often assess, design or modify these tasks while incorporating constraints, including manual force direction and handle interface. This study provides guidance to aid design of pushing and pulling tasks in the context of shoulder physical capacity.

Biomechanically determined hand force limits protecting the low back during occupational pushing and pulling tasks.

Science.gov (United States)

Weston, Eric B; Aurand, Alexander; Dufour, Jonathan S; Knapik, Gregory G; Marras, William S

2018-06-01

Though biomechanically determined guidelines exist for lifting, existing recommendations for pushing and pulling were developed using a psychophysical approach. The current study aimed to establish objective hand force limits based on the results of a biomechanical assessment of the forces on the lumbar spine during occupational pushing and pulling activities. Sixty-two subjects performed pushing and pulling tasks in a laboratory setting. An electromyography-assisted biomechanical model estimated spinal loads, while hand force and turning torque were measured via hand transducers. Mixed modelling techniques correlated spinal load with hand force or torque throughout a wide range of exposures in order to develop biomechanically determined hand force and torque limits. Exertion type, exertion direction, handle height and their interactions significantly influenced dependent measures of spinal load, hand force and turning torque. The biomechanically determined guidelines presented herein are up to 30% lower than comparable psychophysically derived limits and particularly more protective for straight pushing. Practitioner Summary: This study utilises a biomechanical model to develop objective biomechanically determined push/pull risk limits assessed via hand forces and turning torque. These limits can be up to 30% lower than existing psychophysically determined pushing and pulling recommendations. Practitioners should consider implementing these guidelines in both risk assessment and workplace design moving forward.

What Explains the Survival Gap of Pushed and Pulled Corporate Spin-offs?

DEFF Research Database (Denmark)

Rocha, Vera; Carneiro, Anabela; Varum, Celeste

2015-01-01

Unconditionally, pushed spin-offs are found to survive longer than their pulled counterparts. Using matched employer-employee data and novel multivariate decomposition techniques, we show that pushed spin-offs’ relative survival advantage is mostly explained by their larger human capital endowments...

The push-pull tactic for mitigation of mountain pine beetle (Coleoptera: Curculionidae) damage in lodgepole and whitebark pines.

Science.gov (United States)

Gillette, Nancy E; Mehmel, Constance J; Mori, Sylvia R; Webster, Jeffrey N; Wood, David L; Erbilgin, Nadir; Owen, Donald R

2012-12-01

In an attempt to improve semiochemical-based treatments for protecting forest stands from bark beetle attack, we compared push-pull versus push-only tactics for protecting lodgepole pine (Pinus contorta Douglas ex Loudon) and whitebark pine (Pinus albicaulis Engelm.) stands from attack by mountain pine beetle (Dendroctonus ponderosae Hopkins) in two studies. The first was conducted on replicated 4.04-ha plots in lodgepole pine stands (California, 2008) and the second on 0.81-ha plots in whitebark pine stands (Washington, 2010). In both studies, D. ponderosae population levels were moderate to severe. The treatments were 1) push-only (D. ponderosae antiaggregant semiochemicals alone); 2) push-pull (D. ponderosae antiaggregants plus perimeter traps placed at regular intervals, baited with four-component D. ponderosae aggregation pheromone); and 3) untreated controls. We installed monitoring traps baited with two-component D. ponderosae lures inside each plot to assess effect of treatments on beetle flight. In California, fewer beetles were collected in push-pull treated plots than in control plots, but push-only did not have a significant effect on trap catch. Both treatments significantly reduced the rate of mass and strip attacks by D. ponderosae, but the difference in attack rates between push-pull and push-only was not significant. In Washington, both push-pull and push-only treatments significantly reduced numbers of beetles caught in traps. Differences between attack rates in treated and control plots in Washington were not significant, but the push-only treatment reduced attack rates by 30% compared with both the control and push-pull treatment. We conclude that, at these spatial scales and beetle densities, push-only may be preferable for mitigating D. ponderosae attack because it is much less expensive, simpler, and adding trap-out does not appear to improve efficacy.

Push-Pull and Feedback Mechanisms Can Align Signaling System Outputs with Inputs.

Science.gov (United States)

Andrews, Steven S; Peria, William J; Yu, Richard C; Colman-Lerner, Alejandro; Brent, Roger

2016-11-23

Many cell signaling systems, including the yeast pheromone response system, exhibit "dose-response alignment" (DoRA), in which output of one or more downstream steps closely matches the fraction of occupied receptors. DoRA can improve the fidelity of transmitted dose information. Here, we searched systematically for biochemical network topologies that produced DoRA. Most networks, including many containing feedback and feedforward loops, could not produce DoRA. However, networks including "push-pull" mechanisms, in which the active form of a signaling species stimulates downstream activity and the nominally inactive form reduces downstream activity, enabled perfect DoRA. Networks containing feedbacks enabled DoRA, but only if they also compared feedback to input and adjusted output to match. Our results establish push-pull as a non-feedback mechanism to align output with variable input and maximize information transfer in signaling systems. They also suggest genetic approaches to determine whether particular signaling systems use feedback or push-pull control. Copyright © 2016 Elsevier Inc. All rights reserved.

Range expansions transition from pulled to pushed waves with increasing cooperativity in an experimental microbial population

Science.gov (United States)

Gandhi, Saurabh; Yurtsev, Eugene; Korolev, Kirill; Gore, Jeff

Range expansions are becoming more frequent due to environmental changes and rare long distance dispersal, often facilitated by anthropogenic activities. Simple models in theoretical ecology explain many emergent properties of range expansions, such as a constant expansion velocity, in terms of organism-level properties such as growth and dispersal rates. Testing these quantitative predictions in natural populations is difficult because of large environmental variability. Here, we used a controlled microbial model system to study range expansions of populations with and without intra-specific cooperativity. For non-cooperative growth, the expansion dynamics were dominated by population growth at the low-density front, which pulled the expansion forward. We found these expansions to be in close quantitative agreement with the classical theory of pulled waves by Fisher and Skellam, suitably adapted to our experimental system. However, as cooperativity increased, the expansions transitioned to being pushed, i.e. controlled by growth in the bulk as well as in the front. Although both pulled and pushed waves expand at a constant velocity and appear otherwise similar, their distinct dynamics leads to very different evolutionary consequences. Given the prevalence of cooperative growth in nature, understanding the effects of cooperativity is essential to managing invading species and understanding their evolution.

Initial Assessment of the Acceptability of a Push-Pull Aedes aegypti Control Strategy in Iquitos, Peru and Kanchanaburi, Thailand

Science.gov (United States)

Paz-Soldan, Valerie A.; Plasai, Valaikanya; Morrison, Amy C.; Rios-Lopez, Esther J.; Guedez-Gonzales, Shirly; Grieco, John P.; Mundal, Kirk; Chareonviriyaphap, Theeraphap; Achee, Nicole L.

2011-01-01

As part of a larger research program evaluating chemical threshold levels for a Push-Pull intervention to reduce man-vector (Aedes aegypti) contact, this qualitative study explored local perceptions and strategies associated with mosquito control within dengue-endemic communities in Peru and Thailand. Focus groups were used to provide preliminary information that would identify possible public acceptance issues to the Push-Pull strategy in each site. Nine focus group discussions (total of 102 individuals) conducted between September 2008 and March 2009 examined several themes: 1) current mosquito control practices; 2) perceptions of spatial repellency and contact irritancy versus killing mosquitoes; and 3) initial perceptions toward mosquito host-seeking traps. Results indicate participants use household-level strategies for insect control that reveal familiarity with the concept of spatial repellent and contact irritant actions of chemicals and that placing traps in the peridomestic environment to remove repelled mosquitoes was acceptable. Preliminary evidence suggests a Push-Pull strategy should be well accepted in these locations. These results will be beneficial for developing future large scale push-pull interventions and are currently being used to guide insecticide application strategies in (entomological) proof-of-concept studies using experimental huts. PMID:21292886

Study on pollution control in residential kitchen based on the push-pull ventilation system

DEFF Research Database (Denmark)

Zhou, Bin; Chen, Feng; Dong, Zhibo

2016-01-01

Highlights •The push-pull ventilation system is proposed to improve IAQ inside kitchen, where air is supplied through slot air curtain and then exhausted through range hood. •CO2 reduction efficiency with application of air curtain in experiment and simulation in breathing zone was 23.7% and 23.......1%, respectively. •By orthogonal method, the influence of factors on pollution control of the push-pull ventilation system was presented....

Evaluation of Interhandle Distance During Pushing and Pulling of a Four-Caster Cart for Upper Limb Exertion.

Science.gov (United States)

Ohnishi, Akihiro; Takanokura, Masato; Sugama, Atsushi

2016-09-01

This study examined the relationship between interhandle distances and upper limb exertion during simply pushing and pulling of a cart with four swivel wheels, defined by a roll box pallet (RBP) in a Japanese industrial standard. Six healthy young male participants were asked to push and pull an RBP at a distance of 5.2 m under six conditions corresponding to different interhandle distances (40 cm, 60 cm, and 80 cm) and weights (130 kg and 250 kg). The upper limb exertion was studied by shoulder abduction and flexion, and elbow flexion, as well as surface electromyogram (EMG) in shoulder extensor, and elbow flexor and extensor. Participants were required to provide subjective evaluations on operability after each trial. Subjective operability indicated that a narrower interhandle distance had a better operability for pushing. Interhandle distance was also related to upper limb exertion especially for pushing. A narrow interhandle distance caused smaller shoulder adduction but larger elbow flexion. The normalized EMG data revealed that muscular activity became smaller with a narrow interhandle distance in shoulder extensor. During the pulling task, elbow flexion was smaller at a narrow interhandle distance, although subjective operability and normalized EMG were not significantly varied. A wider interhandle distance, such as 80 cm, was not suitable in the forwardbackward movement of the RBP. Therefore, this study concluded that an interhandle distance of 40 cm would be suitable for pushing and pulling an RBP to protect the workers' hands against the risk of injury by installing inner handles.

Simulation and optimization of a polymer directional coupler electro-optic switch with push pull electrodes

Science.gov (United States)

Zheng, Chuan-Tao; Ma, Chun-Sheng; Yan, Xin; Wang, Xian-Yin; Zhang, Da-Ming

2008-07-01

Structural model and design technique are proposed for a polymer directional coupler electro-optic switch with rib waveguides and push-pull electrodes, of which the electric field distribution is analyzed by the conformal transforming method and image method. In order to get the minimum mode loss and the minimum switching voltage, the parameters of the waveguide and electrode are optimized, such as the core with, core thickness, buffer layer between the core and the electrode, coupling gap between the waveguides, electrode thickness, electrode width and electrode gap. Switching Characteristics are analyzed, which include the output power, insertion loss, and crosstalk. To realize normal switching function, the fabrication error, spectrum shift, and coupling loss between a single mode fiber (SMF) and the waveguide are discussed. Simulation results show that the coupling length is 3082 μm, push-pull switching voltage is 2.14 V, insertion loss is less than 1.17 dB, and crosstalk is less than -30 dB for the designed device.

Trunk response and stability in standing under sagittal-symmetric pull-push forces at different orientations, elevations and magnitudes.

Science.gov (United States)

El Ouaaid, Z; Shirazi-Adl, A; Plamondon, A

2018-03-21

To reduce lifting and associated low back injuries, manual material handling operations often involve pulling-pushing of carts at different weights, orientations, and heights. The loads on spine and risk of injury however need to be investigated. The aim of this study was to evaluate muscle forces, spinal loads and trunk stability in pull-push tasks in sagittal-symmetric, static upright standing posture. Three hand-held load magnitudes (80, 120 and 160 N) at four elevations (0, 20, 40 and 60 cm to the L5-S1) and 24 force directions covering all pull/push orientations were considered. For this purpose, a musculoskeletal finite element model with kinematics measured earlier were used. Results demonstrated that peak spinal forces occur under inclined pull (lift) at upper elevations but inclined push at the lowermost one. Minimal spinal loads, on the other hand, occurred at and around vertical pull directions. Overall, spinal forces closely followed variations in the net external moment of pull-push forces at the L5-S1. Local lumbar muscles were most active in pulls while global extensor muscles in lifts. The trunk stability margin decreased with load elevation except at and around horizontal push; it peaked under pulls and reached minimum at vertical lifts. It also increased with antagonist activity in muscles and intra-abdominal pressure. Results provide insight into the marked effects of variation in the load orientation and elevation on muscle forces, spinal loads and trunk stability and hence offer help in rehabilitation, performance enhancement training and design of safer workplaces. Copyright © 2017 Elsevier Ltd. All rights reserved.

Push-you-pull-you: the boundaried self in close relationships.

Science.gov (United States)

Rempel, John K; Burris, Christopher T

2006-02-01

Based on Amoebic Self Theory, the authors propose that the salience of different threats to the self affects the extent to which an intimate relationship partner is pushed away (excluded) or pulled closer (included). When social threat is salient among persons in relationships, it is hypothesized that partners will attempt to defuse the resulting sense of interpersonal vulnerability: offending partners may be pushed away, whereas offenders themselves may draw closer. When spatial-symbolic threat is salient and the relationship's capacity to function as an identity marker is jeopardized, it is hypothesized that the partner--regardless of his or her role--will be pulled closer to maintain the perception that the relationship is secure. Self-report responses to hypothetical scenarios and perceptions of behaviors during a role-play were generally consistent with these hypotheses, suggesting that both an intimate partner and the relationship with that partner can be incorporated into the self.

Exploring tourists push and pull motivations to visit Mauritius as a tourist destination

Directory of Open Access Journals (Sweden)

Hemant Kassean

2013-01-01

Full Text Available This study examines the motivational push and pull-factors that affect tourists’ decision in their choice of a holiday destination. 200 questionnaires were completed using a face to face interview among specific groups of travellers to Mauritius (English, French, German, Italian and South African tourists at various points on the island. The findings demonstrate that rest and relaxation are the most compelling push motivation forces followed by nostalgia, escape, novelty and social interaction. The key pull based motives were found to be the special climate and weather of Mauritius, the exquisite landscape and scenery, unique flora and fauna, exotic beaches, the exotic ambience and atmosphere, the welcoming nature of Mauritian hospitality and the authentic Mauritian culture. The Push and pull factors between first time visitors and repeat visitors are discussed in this article and the study essentially contributes to our overall understanding of why holiday makers take travel decisions to opt for long- haul destinations like Mauritius, and can therefore help destination marketers develop better marketing programmes to meet the specific needs of their customers.

An innovative and efficient method to control the shape of push-pull membrane deformable mirror

NARCIS (Netherlands)

Polo, A.; Haber, A.; Pereira, S.F.; Verhaegen, M.H.G.; Urbach, H.P.

2012-01-01

We carry out performance characterisation of a commercial push and pull deformable mirror with 48 actuators (Adaptica Srl). We present a detailed description of the system as well as a statistical approach on the identification of the mirror influence function. A new efficient control algorithm to

Are pushing and pulling work-related risk factors for upper extremity symptoms? A systematic review of observational studies.

Science.gov (United States)

Hoozemans, M J M; Knelange, E B; Frings-Dresen, M H W; Veeger, H E J; Kuijer, P P F M

2014-11-01

Systematically review observational studies concerning the question whether workers that perform pushing/pulling activities have an increased risk for upper extremity symptoms as compared to workers that perform no pushing/pulling activities. A search in MEDLINE via PubMed and EMBASE was performed with work-related search terms combined with push/pushing/pull/pulling. Studies had to examine exposure to pushing/pulling in relation to upper extremity symptoms. Two authors performed the literature selection and assessment of the risk of bias in the studies independently. A best evidence synthesis was used to draw conclusions in terms of strong, moderate or conflicting/insufficient evidence. The search resulted in 4764 studies. Seven studies were included, with three of them of low risk of bias, in total including 8279 participants. A positive significant relationship with upper extremity symptoms was observed in all four prospective cohort studies with effect sizes varying between 1.5 and 4.9. Two out of the three remaining studies also reported a positive association with upper extremity symptoms. In addition, significant positive associations with neck/shoulder symptoms were found in two prospective cohort studies with effect sizes of 1.5 and 1.6, and with shoulder symptoms in one of two cross-sectional studies with an effect size of 2.1. There is strong evidence that pushing/pulling is related to upper extremity symptoms, specifically for shoulder symptoms. There is insufficient or conflicting evidence that pushing/pulling is related to (combinations of) upper arm, elbow, forearm, wrist or hand symptoms. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Motivation and Perception of Tourists as Push and Pull Factors to Visit National Park

Science.gov (United States)

Said, Jumrin; Maryono

2018-02-01

Push-pull theoretical framework is a popular theory to explain the reason why the tourists decide to visit the destination rather than other place, the kind of experience they want to get and the type of activity they want to do. In this paper, it is explained the motivation as push factors and the perception as pull factors of the tourist in deciding the destination based on previous literature and research using descriptive method. The framework asumed that tourists are motivated to fulfill their needs, including to reduce the psychological imbalance and to gain recognition of social status. National Park is one of destination based on nature or commonly knowns as ecotourism. In choosing the destination, the tourists tend to classify their alternative choice based on several criteria, such as the domination perception of tourist from one destination (pull factor), self motivation (push factor) and the available time and money (situational constraints).

Push an pull forces in the building and construction industry

NARCIS (Netherlands)

Frings-Dresen, M. H. W.; Windhorst, Judith; Hoozemans, M. J M; Van Der Beek, Allard J.; Van der Molen, Henk F.

2000-01-01

Push and pull activities are increasing in the building and construction industry. These activities can be assumed as one of the risk factors for the development of low back and upper extremity complaints. For a risk evaluation, besides the frequency and the duration of the activities, information

Relationship between interstitial and blood glucose in type 1 diabetes patients: delay and the push-pull phenomenon revisited

NARCIS (Netherlands)

Wentholt, Iris M. E.; Hart, Augustus A. M.; Hoekstra, Joost B. L.; DeVries, J. Hans

2007-01-01

BACKGROUND: Interpretation of glucose sensor results requires clarification of the relationship between interstitial (IG) and blood (BG) glucose. We examined the delay of IG upon BG change and reinvestigated the push-pull phenomenon in type 1 diabetes patients. The push-pull phenomenon postulates

Effect of a powered drive on pushing and pulling forces when transporting bariatric hospital beds.

Science.gov (United States)

Wiggermann, Neal

2017-01-01

Powered drives designed to assist with moving hospital beds are commercially available but no studies have evaluated whether they reduce the push and pull forces likely contributing to injury in caregivers. This study measured hand forces of 10 caregivers maneuvering a manual and powered bariatric bed through simulated hospital environments (hallway, elevator, and ramp). Peak push and pull forces exceeded previously established psychophysical limits for all activities with the manual bed. For the powered bed, peak forces were significantly (p pushing did not differ between beds. Powered drive may reduce the risk of injury or the number of caregivers needed for transport. Copyright © 2016 Elsevier Ltd. All rights reserved.

L4-L5 compression and anterior/posterior joint shear forces in cabin attendants during the initial push/pull actions of airplane meal carts

DEFF Research Database (Denmark)

Sandfeld, Jesper; Rosgaard, Christian; Jensen, Bente Rona

2014-01-01

The aim of the present study was to assess the acute low back load of cabin attendants during cart handling and to identify working situations which present the highest strain on the worker. In a setup, 17 cabin attendants (ten females and seven males) pushed, pulled and turned a 20kg standard meal...... was used to calculate the acute L4-L5 load. No working situations created loads greater than the accepted values for single exertions, however compression and anterior/posterior shear forces during pulling and turning were much higher when compared with pushing. There were significant effects of handling...... the cart on different floor types, at the varying inclinations and with different cart weights. Additionally, when external forces were reduced, the cabin attendants did not decrease push/pull force proportionally and thus the L4-L5 load did not decrease as much as expected....

A push-pull system to reduce house entry of malaria mosquitoes

NARCIS (Netherlands)

Menger, D.J.; Otieno, B.; Rijk, de M.; Mukabana, W.R.; Loon, van J.J.A.; Takken, W.

2014-01-01

Background. Mosquitoes are the dominant vectors of pathogens that cause infectious diseases such as malaria, dengue, yellow fever and filariasis. Current vector control strategies often rely on the use of pyrethroids against which mosquitoes are increasingly developing resistance. Here, a push-pull

Three Levels of Push-Pull Dynamics among Chinese International Students' Decision to Study Abroad in the Canadian Context

Science.gov (United States)

Chen, Jun Mian

2017-01-01

The extant literature on student migration flows generally focus on the traditional push-pull factors of migration at the individual level. Such a tendency excludes the broader levels affecting international student mobility. This paper proposes a hybrid of three levels of push-pull dynamics (micro-individual decision-making, meso-academic…

Inclusion at Risk? Push- and Pull-Out Phenomena in Inclusive School Systems: The Italian and Norwegian Experiences

Science.gov (United States)

Nes, Kari; Demo, Heidrun; Ianes, Dario

2018-01-01

The main objective of this article is to explore and compare research data on pull-out and push-out phenomena within inclusive school systems, discussing if and how they represent a risk for inclusion. The terms pull-out and push-out refer to situations in which some groups of students in regular schools learn in settings apart from their peers.…

The limited role of aquifer heterogeneity on metal reduction in an Atlantic coastal plain determined by push-pull tests

International Nuclear Information System (INIS)

Mailloux, Brian J.; Devlin, Stephanie; Fuller, Mark E.; Onstott, T.C.; De Flaun, Mary F.; Choi, K.-H.; Green-Blum, Maria; Swift, Donald J.P.; McCarthy, John; Dong Hailiang

2007-01-01

Sixty push-pull experiments were conducted to determine the factors controlling Fe(III) and Mn(IV) reduction in a well-characterized, shallow, coastal plain aquifer near Oyster, VA, USA. The five multi-level samplers each equipped with 12 ports sampled a heterogeneous portion of the aquifer from 4.4 to 8m-bgs. Each multi-level sampler (MLS) was injected with groundwater that contained NO 3 - and Br - along with: (1) just groundwater (control treatment), (2) humics, (3) lactate (conducted twice) and (4) lactate plus humics. Microbially mediated Fe(III) reduction caused the aqueous Fe Tot concentrations to increase at every depth in the lactate treatment with significant increases within 1 day even while NO 3 - was present. Little change in the Fe Tot concentrations were observed in the control and humics treatment. Humics may have acted as an electron shuttle to increase Fe(III) reduction in the lactate plus humics treatment. The amount of Mn(IV) reduction was significantly lower than that of Fe(III) reduction. Geochemical modeling indicated that gas formation, sorption on reactive surfaces, and mineral precipitation were important processes and that Fe(III) and SO 4 2- reduction were co-occurring. Conditions were favorable for the precipitation of Fe-carbonates, Fe-sulfides and Fe-silicates. In the lactate treatment protist concentrations increased then decreased and planktonic cell concentrations steadily increased, whereas no change was observed in the control treatment. Correlations of Fe(III) reduction with physical and chemical heterogeneity were weak, probably as a result of the abundance of Fe(III) bearing minerals relative to electron donor abundance and that the push-pull test sampled a representative elemental volume that encompassed the microbial diversity within the aquifer. This work indicates that stimulating metal reduction in aquifer systems is a feasible method for remediating heterogeneous subsurface sites contaminated with metals and

Push-Pull Laser-Atomic Oscillator

International Nuclear Information System (INIS)

Jau, Y.-Y.; Happer, W.

2007-01-01

A vapor of alkali-metal atoms in the external cavity of a semiconductor laser, pumped with a time-independent injection current, can cause the laser to self-modulate at the 'field-independent 0-0 frequency' of the atoms. Push-pull optical pumping by the modulated light drives most of the atoms into a coherent superposition of the two atomic sublevels with an azimuthal quantum number m=0. The atoms modulate the optical loss of the cavity at the sharply defined 0-0 hyperfine frequency. As in a maser, the system is not driven by an external source of microwaves, but a very stable microwave signal can be recovered from the modulated light or from the modulated voltage drop across the laser diode. Potential applications for this new phenomenon include atomic clocks, the production of long-lived coherent atomic states, and the generation of coherent optical combs

Small-scale field evaluation of push-pull system against early- and outdoor-biting malaria mosquitoes in an area of high pyrethroid resistance in Tanzania [version 1; referees: 2 approved

Directory of Open Access Journals (Sweden)

Arnold S. Mmbando

2017-11-01

Full Text Available Background: Despite high coverage of indoor interventions like insecticide-treated nets, mosquito-borne infections persist, partly because of outdoor-biting, early-biting and insecticide-resistant vectors. Push-pull systems, where mosquitoes are repelled from humans and attracted to nearby lethal targets, may constitute effective complementary interventions. Methods: A partially randomized cross-over design was used to test efficacy of push-pull in four experimental huts and four local houses, in an area with high pyrethroid resistance in Tanzania. The push-pull system consisted of 1.1% or 2.2% w/v transfluthrin repellent dispensers and an outdoor lure-and-kill device (odour-baited mosquito landing box. Matching controls were set up without push-pull. Adult male volunteers collected mosquitoes attempting to bite them outdoors, but collections were also done indoors using exit traps in experimental huts and by volunteers in the local houses. The collections were done hourly (1830hrs-0730hrs and mosquito catches compared between push-pull and controls. An. gambiae s.l. and An. funestus s.l. were assessed by PCR to identify sibling species, and ELISA to detect Plasmodium falciparum and blood meal sources. Results: Push-pull in experimental huts reduced outdoor-biting for An. arabiensis and Mansonia species by 30% and 41.5% respectively. However, the reductions were marginal and insignificant for An. funestus (12.2%; p>0.05 and Culex (5%; p>0.05. Highest protection against all species occurred before 2200hrs. There was no significant difference in number of mosquitoes inside exit traps in huts with or without push-pull. In local households, push-pull significantly reduced indoor and outdoor-biting of An. arabiensis by 48% and 25% respectively, but had no effect on other species. Conclusion: This push-pull system offered modest protection against outdoor-biting An. arabiensis, without increasing indoor mosquito densities. Additional experimentation

N -annulated perylene-based push-pull-type sensitizers

KAUST Repository

Qi, Qingbiao; Wang, Xingzhu; Fan, Li; Zheng, Bin; Zeng, Wangdong; Luo, Jie; Huang, Kuo-Wei; Wang, Qing; Wu, Jishan

2015-01-01

Alkoxy-wrapped N-annulated perylene (NP) was synthesized and used as a rigid and coplanar π-linker for three push-pull type metal-free sensitizers QB1-QB3. Their optical and electrochemical properties were tuned by varying the structure of acceptor. These new dyes were applied in Co(II)/(III) based dye-sensitized solar cells, and power conversion efficiency up to 6.95% was achieved, indicating that NP could be used as a new building block for the design of high-performance sensitizers in the future.

N -annulated perylene-based push-pull-type sensitizers

KAUST Repository

Qi, Qingbiao

2015-02-06

Alkoxy-wrapped N-annulated perylene (NP) was synthesized and used as a rigid and coplanar π-linker for three push-pull type metal-free sensitizers QB1-QB3. Their optical and electrochemical properties were tuned by varying the structure of acceptor. These new dyes were applied in Co(II)/(III) based dye-sensitized solar cells, and power conversion efficiency up to 6.95% was achieved, indicating that NP could be used as a new building block for the design of high-performance sensitizers in the future.

Human Body Mechanics of Pushing and Pulling: Analyzing the Factors of Task-related Strain on the Musculoskeletal System.

Science.gov (United States)

Argubi-Wollesen, Andreas; Wollesen, Bettina; Leitner, Martin; Mattes, Klaus

2017-03-01

The purpose of this review is to name and describe the important factors of musculoskeletal strain originating from pushing and pulling tasks such as cart handling that are commonly found in industrial contexts. A literature database search was performed using the research platform Web of Science. For a study to be included in this review differences in measured or calculated strain had to be investigated with regard to: (1) cart weight/ load; (2) handle position and design; (3) exerted forces; (4) handling task (push and pull); or (5) task experience. Thirteen studies met the inclusion criteria and proved to be of adequate methodological quality by the standards of the Alberta Heritage Foundation for Medical Research. External load or cart weight proved to be the most influential factor of strain. The ideal handle positions ranged from hip to shoulder height and were dependent on the strain factor that was focused on as well as the handling task. Furthermore, task experience and subsequently handling technique were also key to reducing strain. Workplace settings that regularly involve pushing and pulling should be checked for potential improvements with regards to lower weight of the loaded handling device, handle design, and good practice guidelines to further reduce musculoskeletal disease prevalence.

Design of band-pass push-pull stages of power amplifiers for UHF transmitters of FM and TV broadcasting

OpenAIRE

Titov, A. A.

2005-01-01

The paper considers principles of construction, peculiarities of design, and techniques of network element calculation of push-pull amplification stages in linear bipolar microwave transistors. An example of calculation and results of experimental tests of an amplifier for transmitters of FM and TV broadcasting are presented.

Optical pulling and pushing forces exerted on silicon nanospheres with strong coherent interaction between electric and magnetic resonances.

Science.gov (United States)

Liu, Hongfeng; Panmai, Mingcheng; Peng, Yuanyuan; Lan, Sheng

2017-05-29

We investigated theoretically and numerically the optical pulling and pushing forces acting on silicon (Si) nanospheres (NSs) with strong coherent interaction between electric and magnetic resonances. We examined the optical pulling and pushing forces exerted on Si NSs by two interfering waves and revealed the underlying physical mechanism from the viewpoint of electric- and magnetic-dipole manipulation. As compared with a polystyrene (PS) NS, it was found that the optical pulling force for a Si NS with the same size is enlarged by nearly two orders of magnitude. In addition to the optical pulling force appearing at the long-wavelength side of the magnetic dipole resonance, very large optical pushing force is observed at the magnetic quadrupole resonance. The correlation between the optical pulling/pushing force and the directional scattering characterized by the ratio of the forward to backward scattering was revealed. More interestingly, it was found that the high-order electric and magnetic resonances in large Si NSs play an important role in producing optical pulling force which can be generated by not only s-polarized wave but also p-polarized one. Our finding indicates that the strong coherent interaction between the electric and magnetic resonances existing in nanoparticles with large refractive indices can be exploited to manipulate the optical force acting on them and the correlation between the optical force and the directional scattering can be used as guidance. The engineering and manipulation of optical forces will find potential applications in the trapping, transport and sorting of nanoparticles.

Modelo híbrido pull-push en el sector de las telecomunicaciones

Directory of Open Access Journals (Sweden)

Cristian Arlex Trejos Taborda

2016-07-01

Full Text Available La industria de las telecomunicaciones cambia rápidamente y las barreras de entrada son bajas implicando que la supervivencia en el mercado sea un verdadero desafío para las empresas. En este artículo estudia como los sistemas Pull y Push pueden ser integrados a la cadena de abastecimiento en el sector de telecomunicaciones en Colombia. Se desarrolló un modelo hibrido Pull y Push utilizando dinámica de sistemas en aras de determinar los niveles óptimos y el costo mínimo de inventario, al igual que el nivel óptimo de prestación de servicio a los clientes. Los resultados de la investigación demuestran que el comportamiento del modelo híbrido permite dar respuesta a las necesidades del mercado y de la empresa a la vez, generando niveles de inventario que son mínimos y suficientes para cubrir la demanda.

Optimal Halbach Permanent Magnet Designs for Maximally Pulling and Pushing Nanoparticles.

Science.gov (United States)

Sarwar, A; Nemirovski, A; Shapiro, B

2012-03-01

Optimization methods are presented to design Halbach arrays to maximize the forces applied on magnetic nanoparticles at deep tissue locations. In magnetic drug targeting, where magnets are used to focus therapeutic nanoparticles to disease locations, the sharp fall off of magnetic fields and forces with distances from magnets has limited the depth of targeting. Creating stronger forces at depth by optimally designed Halbach arrays would allow treatment of a wider class of patients, e.g. patients with deeper tumors. The presented optimization methods are based on semi-definite quadratic programming, yield provably globally optimal Halbach designs in 2 and 3-dimensions, for maximal pull or push magnetic forces (stronger pull forces can collect nano-particles against blood forces in deeper vessels; push forces can be used to inject particles into precise locations, e.g. into the inner ear). These Halbach designs, here tested in simulations of Maxwell's equations, significantly outperform benchmark magnets of the same size and strength. For example, a 3-dimensional 36 element 2000 cm(3) volume optimal Halbach design yields a ×5 greater force at a 10 cm depth compared to a uniformly magnetized magnet of the same size and strength. The designed arrays should be feasible to construct, as they have a similar strength (≤ 1 Tesla), size (≤ 2000 cm(3)), and number of elements (≤ 36) as previously demonstrated arrays, and retain good performance for reasonable manufacturing errors (element magnetization direction errors ≤ 5°), thus yielding practical designs to improve magnetic drug targeting treatment depths.

Evaluation of methods to assess push/pull forces in a construction task

NARCIS (Netherlands)

Hoozemans, M J; Van Der Beek, Allard J.; Frings-Dresena, M H; Van der Molen, Henk F.

2001-01-01

The objective of the present study was to determine the validity of methods to assess push/pull forces exerted in a construction task. Forces assessed using a hand-held digital force gauge were compared to those obtained using a highly accurate measuring frame. No significant differences were found

Control and Modeling of Push-Pull Forward Three-Level Converter for Microgrid

DEFF Research Database (Denmark)

Yao, Zhilei; Xu, Jing; Guerrero, Josep M.

2015-01-01

Renewable energy sources are widely used in microgrid. Output voltage of them is often low and varies widely. Because diodes in three-level legs in traditional three-level (TL) converter are substituted by MOSFETs, the push-pull forward (PPF) TL converter is very suitable for wide and low...

A triphenylamine-based push-pull – σ – C60 dyad as photoactive molecular material for single-component organic solar cells: synthesis, characterizations and photophysical properties

KAUST Repository

Labrunie, Antoine; Gorenflot, Julien; Babics, Maxime; Aleveque, Olivier; Dabos-Seignon, Sylvie; Balawi, Ahmed H.; Kan, Zhipeng; Wohlfahrt, Markus; Levillain, Eric; Hudhomme, Pietrick; Beaujuge, Pierre; Laquai, Fré dé ric; Cabanetos, Clé ment; Blanchard, Philippe

2018-01-01

A push-pull – σ – C60 molecular dyad was synthesized via Huisgen-type click-chemistry and used as photoactive material for single-component organic solar cells. Steady-state photoluminescence (PL) experiments of the dyad in solution show a significant quenching of the emission of the push-pull moiety. Spin-casting of a solution of the dyad results in homogenous and smooth thin-films, which exhibit complete PL quenching in line with ultrafast photo-induced electron-transfer in the solid-state. Spectro-electrochemistry reveals the optical signatures of radical cations and radical anions. Evaluation of the charge carrier mobility by space-charge limited current measurements gives an electron-mobility of μe = 4.3 × 10-4 cm2 V-1 s-1, ca. 50 times higher than the hole-mobility. Single-component organic solar cells yield an open-circuit voltage Voc of 0.73 V and a short-circuit current density of 2.1 mA cm-2 however, a poor fill-factor FF (29%) is obtained, resulting in low power conversion efficiency of only 0.4%. Combined TA and time-delayed collection field (TDCF) experiments show mostly ultrafast photon-to-charge conversion and a small component of diffusion-limited exciton dissociation, revealing the presence of pure fullerene domains. Furthermore, a strong field dependence of charge generation is observed, governing the device fill factor, which is further reduced by a competition between extraction and fast recombination of separated charges.

A triphenylamine-based push-pull – σ – C60 dyad as photoactive molecular material for single-component organic solar cells: synthesis, characterizations and photophysical properties

KAUST Repository

Labrunie, Antoine

2018-04-23

A push-pull – σ – C60 molecular dyad was synthesized via Huisgen-type click-chemistry and used as photoactive material for single-component organic solar cells. Steady-state photoluminescence (PL) experiments of the dyad in solution show a significant quenching of the emission of the push-pull moiety. Spin-casting of a solution of the dyad results in homogenous and smooth thin-films, which exhibit complete PL quenching in line with ultrafast photo-induced electron-transfer in the solid-state. Spectro-electrochemistry reveals the optical signatures of radical cations and radical anions. Evaluation of the charge carrier mobility by space-charge limited current measurements gives an electron-mobility of μe = 4.3 × 10-4 cm2 V-1 s-1, ca. 50 times higher than the hole-mobility. Single-component organic solar cells yield an open-circuit voltage Voc of 0.73 V and a short-circuit current density of 2.1 mA cm-2 however, a poor fill-factor FF (29%) is obtained, resulting in low power conversion efficiency of only 0.4%. Combined TA and time-delayed collection field (TDCF) experiments show mostly ultrafast photon-to-charge conversion and a small component of diffusion-limited exciton dissociation, revealing the presence of pure fullerene domains. Furthermore, a strong field dependence of charge generation is observed, governing the device fill factor, which is further reduced by a competition between extraction and fast recombination of separated charges.

Pushing and pulling in relation to musculoskeletal disorders : a review of risk factors

NARCIS (Netherlands)

Hoozemans, M J; Van Der Beek, Allard J.; Frings-Dresen, M. H. W.; Dijk, F.J.H.; van der Woude, L H

The objective was to review the literature on risk factors for musculoskeletal disorders related to pushing and pulling. The risk factors have been described and evaluated from four perspectives: epidemiology, psychophysics, physiology, and biomechanics. Epidemiological studies have shown, based on

Pushing and pulling in relation to musculoskeletal disorders: a review of risk factors

NARCIS (Netherlands)

Hoozemans, Marco; van der Beek, A.J.; Frings-Dresen, M.H.W.; Dijk, F.J.H.

1998-01-01

The objective was to review the literature on risk factors for musculoskeletal disorders related to pushing and pulling. The risk factors have been described and evaluated from four perspectives: epidemiology, psychophysics, physiology, and biomechanics. Epidemiological studies have shown, based on

Mechanical load on the low back and shoulders during pushing and pulling of two-wheeled waste containers compared with lifting and carrying of bags and bins.

Science.gov (United States)

Schibye, B; Søgaard, K; Martinsen, D; Klausen, K

2001-08-01

Compare the mechanical load on the low back and shoulders during pushing and pulling a two-wheeled container with the load during lifting and carrying the same amount of waste. Only little is known about risk factors and mechanical loads during push/pull operations. A complete 2(3) factor push/pull experiment. A two-wheeled container with 25 or 50 kg was pushed in front of and pulled behind the body by seven waste collectors. Further, the same subjects lifted and carried a paper bag and a dustbin both loaded with 7 and 25 kg. All operations were video recorded and the push/pull force was measured by means of a three-dimensional force transducer. Peak Motus and Watbak software were used for digitising and calculation of torque at L4/L5 and the shoulder joints and compression and shear forces at L4/L5. During pushing and pulling the compression at L4/L5 is from 605 to 1445 N. The extension torque at L4/L5 produced by the push/pull force is counteracted by the forward leaning of the upper body. The shear force is below 202 N in all situations. The torque at the shoulders is between 1 and 38 Nm. In the present experiments the torques at the low back and the shoulders are low during pushing and pulling. No relation exists between the size of the external force and the torque at the low back and the shoulder. Pushing and pulling are common in many workplaces and have often replaced lifting and carrying situations. This has emphasised the need for more knowledge of the internal mechanical load on the body during these activities.

Acceptor number-dependent ultrafast photo-physical properties of push-pull chromophores using time-resolved methods

Science.gov (United States)

Chi, Xiao-Chun; Wang, Ying-Hui; Gao, Yu; Sui, Ning; Zhang, Li-Quan; Wang, Wen-Yan; Lu, Ran; Ji, Wen-Yu; Yang, Yan-Qiang; Zhang, Han-Zhuang

2018-04-01

Three push-pull chromophores comprising a triphenylamine (TPA) as electron-donating moiety and functionalized β-diketones as electron acceptor units are studied by various spectroscopic techniques. The time-correlated single-photon counting data shows that increasing the number of electron acceptor units accelerates photoluminescence relaxation rate of compounds. Transient spectra data shows that intramolecular charge transfer (ICT) takes place from TPA units to β-diketones units after photo-excitation. Increasing the number of electron acceptor units would prolong the generation process of ICT state, and accelerate the excited molecule reorganization process and the relaxation process of ICT state.

''Push-pull'' gastrostomy: a new technique for percutaneous gastrostomy tube insertion in the neonate and young infant

International Nuclear Information System (INIS)

Cahill, A.M.; Kaye, R.D.; Fitz, C.R.; Towbin, R.B.

2001-01-01

Objective. To evaluate a newly developed method combining antegrade and retrograde techniques for percutaneous gastrostomy tube (PGT) insertion in the neonate and young infant. Materials and methods. From January 1994 to December 2000, 85 children (47 male, 38 female), mean age 4.5 months (range 0.44-9.13 months) underwent PGT insertion using the ''push-pull'' technique. With the addition, 57 children had a jejunostomy tube placed as well at or within 24 h of the PGT procedure. The mean weight was 3.74 kg, range 1.5-7.0 kg. The indications for the procedure included failure to thrive in 40 patients (25 %), static encephalopathy in 21 (25 %), neurological/congenital abnormalities in 12 (14 %), aspiration in 7 (8 %), and cardiac problems in 5 (6 %). Results. Eighty-five PGTs were successfully inserted in 85 children. One procedure was initially unsuccessful due to failed conscious sedation and was completed under general anesthesia. Four of 85 patients initially had attempted antegrade placement that failed, and the procedure was successfully completed using the ''push-pull'' method. One major complication occurred: a gastrocolic fistula at day 5 post-procedure, which was surgically repaired without sequelae. Tube-related problems included; tube dislodgement (n = 1) and procedure-related stomal infection (n = 3). Conclusion. The ''push-pull'' gastrostomy technique is a safe, effective method of percutaneous gastrostomy tube placement in neonates. It facilitates successful placement of the PGT in patients in whom the classic antegrade method is not possible. It has become the procedure of choice in this group. (orig.)

Single borehole test sensitivity towards crack and rock parameter. Lesson Hortberg; Einbohrlochtracertestsensitivitaet gegenueber Riss und Gesteinsparametern. Lektion Horstberg

Energy Technology Data Exchange (ETDEWEB)

Ghergut, Iulia; Behrens, Horst; Sauter, Martin [Goettingen Univ. (Germany). Angewandte Geologie

2012-10-16

The novel experiments of the GeoZentrum Hanover (Hanover, Federal Republic of Germany) on geothermal energy at the well bore Horstberg in the south heath also motivated the accompanying tracertest-mindset to move away from the tracer job stereotypes. For some possible designs at the tracertest at this drilling (forced-gradient divergent push by water fracking of Detfurth perforation, single-screen push-pull at Solling perforation, single-screen push-pull at Detfurth perforation, and so forth) the analysis shows how and why the controlling parameter do not comply with the mental basic pattern of the expectations at the tracertests ('tracertest by crack {yields} characterization of the crack', 'tracer residence time {yields} prognosis of the thermal lifetime').

Synthesis and characterization of a push-pull terpolymer based on anthracene, fluorene and benzothiadiazole

Energy Technology Data Exchange (ETDEWEB)

Floriano, Ana Carolina; Silveira, Daiana Santos; Cristovan, Fernando Henrique, E-mail: carolina.floriano@unifesp.br [Universidade Federal de Sao Paulo (UNIFESP), Sao Jose dos Campos, SP (Brazil); Rosa, Gabriel Marques; Liao, Luciano Morais [Universidade Federal de Goias (UFG), Goiania, GO (Brazil); Piovessan, Erick [Universidade Federal de Uberlandia (UFU), MG (Brazil)

2016-07-01

Full text: The development of organic optoelectronic devices with higher efficiency required new forms of polymers with strong donor-acceptor character (D-A), called a push-pull polymers. Most studies of organic polymers used in optoelectronic applications are centered on poly(3-hexylthiophene) with high regioregularity. However, there are other polymers synthesized with monomers that enables the possibility to adapt its electrical and optical properties. Polyfluorene derivatives show interesting chemical and physical properties due to a rigid planar biphenyl unit that are easily substituted at the remote C-9 position, improving the its processability in relation to polyfluorene, so it can be can be processed by spin-coating and many others deposition techniques. Fluorene derivatives copolymers prepared with anthracene unit improve electrochemical properties and present good photo and electroluminescence properties, due to an enhancement of the system conjugation. The benzothiadiazole, known by their environmental stability, planarity and electron-withdrawing nature, are a promising molecule in push−pull type semiconducting polymers. In this study proceed with the terpolymer synthesis containing 9,9-Dihexylfluorene and anthracene as pushing unit and benzothiadiazole as pushing unit. Also we synthesized the poly(9,9-dihexylfluorene)-co-(anthracene) and poly(9,9- dihexylfluorene)-co-(benzothiadiazole) copolymers. The polymers were synthesized using Suzuki coupling and characterized by FT-IR spectroscopy that shows the characteristic monomer bands and the polymer formation were confirmed by {sup 1}H-NMR. Polymerization yield of three polymers were about 50-70%. Polymers present good solubility in common organic solvent such as chloroform. Terpolymer UV-Vis spectra revealed broadband absorbance from 300 to 680nm and absorption maximum at 441 nm. Finally, the preliminary results indicate that the push-pull terpolymer is a promising broadband absorbing polymer for

Synthesis and characterization of a push-pull terpolymer based on anthracene, fluorene and benzothiadiazole

International Nuclear Information System (INIS)

Floriano, Ana Carolina; Silveira, Daiana Santos; Cristovan, Fernando Henrique; Rosa, Gabriel Marques; Liao, Luciano Morais; Piovessan, Erick

2016-01-01

Full text: The development of organic optoelectronic devices with higher efficiency required new forms of polymers with strong donor-acceptor character (D-A), called a push-pull polymers. Most studies of organic polymers used in optoelectronic applications are centered on poly(3-hexylthiophene) with high regioregularity. However, there are other polymers synthesized with monomers that enables the possibility to adapt its electrical and optical properties. Polyfluorene derivatives show interesting chemical and physical properties due to a rigid planar biphenyl unit that are easily substituted at the remote C-9 position, improving the its processability in relation to polyfluorene, so it can be can be processed by spin-coating and many others deposition techniques. Fluorene derivatives copolymers prepared with anthracene unit improve electrochemical properties and present good photo and electroluminescence properties, due to an enhancement of the system conjugation. The benzothiadiazole, known by their environmental stability, planarity and electron-withdrawing nature, are a promising molecule in push−pull type semiconducting polymers. In this study proceed with the terpolymer synthesis containing 9,9-Dihexylfluorene and anthracene as pushing unit and benzothiadiazole as pushing unit. Also we synthesized the poly(9,9-dihexylfluorene)-co-(anthracene) and poly(9,9- dihexylfluorene)-co-(benzothiadiazole) copolymers. The polymers were synthesized using Suzuki coupling and characterized by FT-IR spectroscopy that shows the characteristic monomer bands and the polymer formation were confirmed by 1 H-NMR. Polymerization yield of three polymers were about 50-70%. Polymers present good solubility in common organic solvent such as chloroform. Terpolymer UV-Vis spectra revealed broadband absorbance from 300 to 680nm and absorption maximum at 441 nm. Finally, the preliminary results indicate that the push-pull terpolymer is a promising broadband absorbing polymer for

Optimal Design of a Push-Pull-Forward Half-Bridge (PPFHB) Bidirectional DC–DC Converter With Variable Input Voltage

DEFF Research Database (Denmark)

Zhang, Zhe; Thomsen, Ole Cornelius; Andersen, Michael A. E.

2012-01-01

This paper presents a low-cost bidirectional isolated dc–dc converte, derived from dual-active-bridge converter for the power sources with variable output voltage like supercapacitors. The proposed converter consists of push-pull-forward circuit half-bridge circuit (PPFHB) and a high-frequency tr......This paper presents a low-cost bidirectional isolated dc–dc converte, derived from dual-active-bridge converter for the power sources with variable output voltage like supercapacitors. The proposed converter consists of push-pull-forward circuit half-bridge circuit (PPFHB) and a high...

A centrifuge simulated push-pull manoeuvre with subsequent reduced +Gz tolerance.

Science.gov (United States)

Xu, Yan; Li, Bao-Hui; Zhang, Li-Hui; Jin, Zhao; Wei, Xiao-Yang; Wang, Hong; Wu, San-Yuan; Wang, Hai-Xia; Wang, Quan; Yan, Gui-Ding; Deng, Lue; Geng, Xi-Chen

2012-07-01

The push-pull effect (PPE) has been recognized as a deleterious contributor to fatal flight accidents. The purpose of the study was to establish a push-pull manoeuvre (PPM) simulation with a tri-axes centrifuge, studying the effect of this PPM on the +Gz tolerance, and to make this simulation suitable for pilot centrifuge training. The PPM was realized through pre-programmed acceleration profiles consisting of -1 Gz for 5 s followed by a +Gz plateau for 10 s. Relaxed +Gz tolerance recordings were obtained from 20 healthy male fighter aircraft pilots and 6 healthy male volunteers through exposure to pre-programmed profiles with and without previous -1 Gz exposure. A statistically significant decrease in +Gz tolerance was seen in all subjects after -1 Gz for 5 s exposure, 0.87 ± 0.13 G in the volunteer group and 0.95 ± 0.25 G in the pilot group. The ear opacity pulse as a +Gz tolerance endpoint criterion was sometimes found to be unreliable during the PPM experiments. The simulated PPM in this study elicited a PPE, which was obvious from the significant reduction in +Gz tolerance. The PPM profile appears useful to be included in centrifuge training.

From the Push of Fear, to the Pull of Hope: Learning by design ...

African Journals Online (AJOL)

From the Push of Fear, to the Pull of Hope: Learning by design. S Sterling. Abstract. No Abstract. Full Text: EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT · Creative Commons License This work is licensed under a Creative Commons Attribution 3.0 License.

Mechanical loading of the low back and shoulders during pushing and pulling activities.

NARCIS (Netherlands)

Hoozemans, M.J.M.; Kingma, I.; Dieen, van J.H.; Vries, de W.K.H.; Woude, van der L.H.V.; Veeger, H.E.J.; Frings-Dresen, M.H.W.; Beek, van der A.J.

2004-01-01

The objective of this study was to quantify the mechanical load on the low back and shoulders during pushing and pulling in combination with three task constraints: the use of one or two hands, three cart weights, and two handle heights. The second objective was to explore the relation between the

Mechanical loading of the low back and shoulders during pushing and pulling activities

NARCIS (Netherlands)

Hoozemans, Marco J. M.; Kuijer, P. Paul F. M.; Kingma, Idsart; van Dieën, Jaap H.; de Vries, Wiebe H. K.; van der Woude, Luc H. V.; Veeger, Dirk Jan H. E. J.; van der Beek, Allard J.; Frings-Dresen, Monique H. W.

2004-01-01

The objective of this study was to quantify the mechanical load on the low back and shoulders during pushing and pulling in combination with three task constraints: the use of one or two hands, three cart weights, and two handle heights. The second objective was to explore the relation between the

Voices from the "Working Lives" Project: The Push-Pull of Work and Care

Science.gov (United States)

Fehring, Heather; Herring, Katherine

2012-01-01

A recent policy direction in many OECD countries has been to increase workforce participation for women of childbearing age; a policy direction which seemingly runs counter to a need for improved work-life balance for women themselves. This article explores the impact of this somewhat contradictory "push-pull" of policy by examining some…

Single borehole test sensitivity towards crack and rock parameter. Lesson Hortberg; Einbohrlochtracertestsensitivitaet gegenueber Riss und Gesteinsparametern. Lektion Horstberg

Energy Technology Data Exchange (ETDEWEB)

Ghergut, Iulia; Behrens, Horst; Sauter, Martin [Goettingen Univ. (Germany). Angewandte Geologie

2012-10-16

The novel experiments of the GeoZentrum Hanover (Hanover, Federal Republic of Germany) on geothermal energy at the well bore Horstberg in the south heath also motivated the accompanying tracertest-mindset to move away from the tracer job stereotypes. For some possible designs at the tracertest at this drilling (forced-gradient divergent push by water fracking of Detfurth perforation, single-screen push-pull at Solling perforation, single-screen push-pull at Detfurth perforation, and so forth) the analysis shows how and why the controlling parameter do not comply with the mental basic pattern of the expectations at the tracertests ('tracertest by crack {yields} characterization of the crack', 'tracer residence time {yields} prognosis of the thermal lifetime').

Integration of market pull and technology push in the corporate front end and innovation management - Insights from the German software industry

DEFF Research Database (Denmark)

Brem, Alexander; Voigt, K.-I.

2009-01-01

Within the framework of this paper, an extensive literature overview of technology and innovation management aspects on market pull and technology push will be given. The existing classification of market pull and technology push will be particularly shown and called into question by suggesting...... a conceptual framework. Additionally, the most common front end innovation models will be introduced. Finally, the authors will introduce how a technology-based service company is managing the connection of these two alternatives. A special focus will be laid on the accordant methods in order to search...... will be introduced as to how market pull and technology push activities within the corporate technology and innovation management can be integrated. Hence, the purpose of the paper is to introduce a theory-based conceptual framework that can be used in today’s corporate environment. In this context, technology...

Do PhDs Voluntarily Opt for Private Sector Employment? Evidence of Push and Pull Effects on Mobility Choices

DEFF Research Database (Denmark)

Pedersen, Heidi Skovgaard

2014-01-01

In Denmark, policy makers have increased admissions to PhD programs to ensure the flow of researchers into the private sector, thereby increasing knowledge transfer. However, we know little about the factors influencing the sector mobility of PhD graduates. While opting for employment...... in the private sector might be driven by personal preferences, there might also be external factors pushing PhDs to choose the private sector. This article examines the push and pull effects on mobility choices using duration models to estimate the transition rates to private sector employment. The analyses show...... that the preference for and ability to do academic science reduces transition rates to the private sector, whereas being in a research position and earnings potential are attractors to the private sector. Hence, both push and pull effects determine sector mobility. Once the initial sector choice has been made...

L4-L5 compression and anterior/posterior joint shear forces in cabin attendants during the initial push/pull actions of airplane meal carts.

Science.gov (United States)

Sandfeld, Jesper; Rosgaard, Christian; Jensen, Bente Rona

2014-07-01

The aim of the present study was to assess the acute low back load of cabin attendants during cart handling and to identify working situations which present the highest strain on the worker. In a setup, 17 cabin attendants (ten females and seven males) pushed, pulled and turned a 20 kg standard meal cart (L: 0.5m × W: 0.3 m × H: 0.92 m) loaded with extra 20 kg and 40 kg, respectively on two different surfaces (carpet and linoleum) and at three floor inclinations (-2°, 0° and +2°). Two force transducers were mounted as handles. Two-dimensional movement analysis was performed and a 4D WATBAK modelling tool was used to calculate the acute L4-L5 load. No working situations created loads greater than the accepted values for single exertions, however compression and anterior/posterior shear forces during pulling and turning were much higher when compared with pushing. There were significant effects of handling the cart on different floor types, at the varying inclinations and with different cart weights. Additionally, when external forces were reduced, the cabin attendants did not decrease push/pull force proportionally and thus the L4-L5 load did not decrease as much as expected. Copyright © 2014 Elsevier Ltd and The Ergonomics Society. All rights reserved.

The Effects of Direction of Exertion, Path, and Load Placement in Nursing Cart Pushing and Pulling Tasks: An Electromyographical Study.

Science.gov (United States)

Kao, Huei Chu; Lin, Chiuhsiang Joe; Lee, Yung Hui; Chen, Su Huang

2015-01-01

The purpose of this study was to explore the effects of direction of exertion (DOE) (pushing, pulling), path (walking in a straight line, turning left, walking uphill), and load placement (LP) (the 18 blocks were indicated by X, Y and Z axis; there were 3 levels on the X axis, 2 levels on the Y axis, and 3 levels on the Z axis) on muscle activity and ratings of perceived exertion in nursing cart pushing and pulling tasks. Ten participants who were female students and not experienced nurses were recruited to participate in the experiment. Each participant performed 108 experimental trials in the study, consisting of 2 directions of exertion (push and pull), 3 paths, and 18 load placements (indicated by X, Y and Z axes). A 23kg load was placed into one load placement. The dependent variables were electromyographic (EMG) data of four muscles collected bilaterally as follows: Left (L) and right (R) trapezius (TR), flexor digitorum superficialis (FDS), extensor digitorum (ED), and erector spinae (ES) and subjective ratings of perceived exertion (RPE). Split-split-plot ANOVA was conducted to analyze significant differences between DOE, path, and LP in the EMG and RPE data. Pulling cart tasks produced a significantly higher activation of the muscles (RTR:54.4%, LTR:50.3%, LFDS:57.0%, LED:63.4%, RES:40.7%, LES:36.7%) than pushing cart tasks (RTR:42.4%, LTR:35.1%, LFDS:32.3%, LED:55.1%, RES:33.3%, LES:32.1%). A significantly greater perceived exertion was found in pulling cart tasks than pushing cart tasks. Significantly higher activation of all muscles and perceived exertion were observed for walking uphill than walking in a straight line and turning left. Significantly lower muscle activity of all muscles and subject ratings were observed for the central position on the X axis, the bottom position on the Y axis, and the posterior position on the Z axis. These findings suggest that nursing staff should adopt forward pushing when moving a nursing cart, instead of backward

Subtle trade-off existing between (anti)aromaticity, push-pull interaction, keto-enol tautomerism, and steric hindrance when defining the electronic properties of conjugated structures.

Science.gov (United States)

Kleinpeter, Erich; Bölke, Ute; Koch, Andreas

2010-07-22

The spatial magnetic properties (through space NMR shieldings, TSNMRS) of conjugated structures (benzenoid/quinonoid keto/enol tautomers, 1,3-dihydroxyaryl-2-aldehydes, Don-pi-Acc chromophores with trade-off existing push-pull vs aromatic behavior) have been calculated by the GIAO perturbation method employing the nucleus independent chemical shift (NICS) concept, and visualized as iso-chemical-shielding surfaces (ICSS) of various size and direction. The TSNMRS values, thus obtained, can be successfully employed to quantify and visualize (anti)aromaticity and to identify readily hereby zwitterionic structures due to push-pull behavior of the compounds studied. In addition, the push-pull behavior was quantified by the quotient (pi*/pi) approach of the central partial C=C double bond.

Impact of hand forces and start/stop frequency on physiological responses to three forms of pushing and pulling: a South African perspective.

Science.gov (United States)

Ai, Todd

2012-01-01

There has been limited attention given to the physiological demands of pushing and pulling, especially in industrially developing countries such as South Africa. Two key factors affecting the physiological demands of these tasks are the hand forces exerted and the start/stop frequency. The purpose of the current study was therefore to investigate the physiological responses to pushing and pulling at various loads and start/stop frequencies. 36 male subjects participated in the study and were required to complete a total of 18 conditions (three techniques: pushing, two- and one-handed pulling; three loads: 200, 350 and 500 kg; and two frequencies: 2 and 4 stops per minute). During each condition the heart rate, oxygen uptake and energy expenditure were measured. Pushing was found to elicit significantly lower responses for all three dependent variables than either form of pulling. The start/stop frequency was also found to have a significant impact on subject responses. The findings of this study indicate that the technique adopted to maneuver loads is critical in determining the physical demands placed on the human operator. Furthermore increasing the frequency of start/stops plays an important role, thus the forces exerted during these two phases are important from a physiological perspective.

Ion Concentration- and Voltage-Dependent Push and Pull Mechanisms of Potassium Channel Ion Conduction.

Directory of Open Access Journals (Sweden)

Kota Kasahara

Full Text Available The mechanism of ion conduction by potassium channels is one of the central issues in physiology. In particular, it is still unclear how the ion concentration and the membrane voltage drive ion conduction. We have investigated the dynamics of the ion conduction processes in the Kv1.2 pore domain, by molecular dynamics (MD simulations with several different voltages and ion concentrations. By focusing on the detailed ion movements through the pore including selectivity filter (SF and cavity, we found two major conduction mechanisms, called the III-IV-III and III-II-III mechanisms, and the balance between the ion concentration and the voltage determines the mechanism preference. In the III-IV-III mechanism, the outermost ion in the pore is pushed out by a new ion coming from the intracellular fluid, and four-ion states were transiently observed. In the III-II-III mechanism, the outermost ion is pulled out first, without pushing by incoming ions. Increases in the ion concentration and voltage accelerated ion conductions, but their mechanisms were different. The increase in the ion concentrations facilitated the III-IV-III conductions, while the higher voltages increased the III-II-III conductions, indicating that the pore domain of potassium channels permeates ions by using two different driving forces: a push by intracellular ions and a pull by voltage.

Optimal Halbach permanent magnet designs for maximally pulling and pushing nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Sarwar, A., E-mail: azeem@umd.edu [Fischell Department of Bioengineering, College Park, MD (United States); University of Maryland at College Park (United States); Nemirovski, A. [H. Milton Stewart School of Industrial and Systems Engineering (ISyE), Georgia Institute of Technology (United States); Shapiro, B. [Fischell Department of Bioengineering, College Park, MD (United States); Institute for Systems Research (United States); University of Maryland at College Park (United States)

2012-03-15

Optimization methods are presented to design Halbach arrays to maximize the forces applied on magnetic nanoparticles at deep tissue locations. In magnetic drug targeting, where magnets are used to focus therapeutic nanoparticles to disease locations, the sharp fall off of magnetic fields and forces with distances from magnets has limited the depth of targeting. Creating stronger forces at a depth by optimally designed Halbach arrays would allow treatment of a wider class of patients, e.g. patients with deeper tumors. The presented optimization methods are based on semi-definite quadratic programming, yield provably globally optimal Halbach designs in 2 and 3-dimensions, for maximal pull or push magnetic forces (stronger pull forces can collect nanoparticles against blood forces in deeper vessels; push forces can be used to inject particles into precise locations, e.g. into the inner ear). These Halbach designs, here tested in simulations of Maxwell's equations, significantly outperform benchmark magnets of the same size and strength. For example, a 3-dimensional 36 element 2000 cm{sup 3} volume optimal Halbach design yields a 5 Multiplication-Sign greater force at a 10 cm depth compared to a uniformly magnetized magnet of the same size and strength. The designed arrays should be feasible to construct, as they have a similar strength ({<=}1 T), size ({<=}2000 cm{sup 3}), and number of elements ({<=}36) as previously demonstrated arrays, and retain good performance for reasonable manufacturing errors (element magnetization direction errors {<=}5 Degree-Sign), thus yielding practical designs to improve magnetic drug targeting treatment depths. - Highlights: Black-Right-Pointing-Pointer Optimization methods presented to design Halbach arrays for drug targeting. Black-Right-Pointing-Pointer The goal is to maximize forces on magnetic nanoparticles at deep tissue locations. Black-Right-Pointing-Pointer The presented methods yield provably globally optimal Halbach

Optimal Halbach permanent magnet designs for maximally pulling and pushing nanoparticles

International Nuclear Information System (INIS)

Sarwar, A.; Nemirovski, A.; Shapiro, B.

2012-01-01

Optimization methods are presented to design Halbach arrays to maximize the forces applied on magnetic nanoparticles at deep tissue locations. In magnetic drug targeting, where magnets are used to focus therapeutic nanoparticles to disease locations, the sharp fall off of magnetic fields and forces with distances from magnets has limited the depth of targeting. Creating stronger forces at a depth by optimally designed Halbach arrays would allow treatment of a wider class of patients, e.g. patients with deeper tumors. The presented optimization methods are based on semi-definite quadratic programming, yield provably globally optimal Halbach designs in 2 and 3-dimensions, for maximal pull or push magnetic forces (stronger pull forces can collect nanoparticles against blood forces in deeper vessels; push forces can be used to inject particles into precise locations, e.g. into the inner ear). These Halbach designs, here tested in simulations of Maxwell's equations, significantly outperform benchmark magnets of the same size and strength. For example, a 3-dimensional 36 element 2000 cm 3 volume optimal Halbach design yields a 5× greater force at a 10 cm depth compared to a uniformly magnetized magnet of the same size and strength. The designed arrays should be feasible to construct, as they have a similar strength (≤1 T), size (≤2000 cm 3 ), and number of elements (≤36) as previously demonstrated arrays, and retain good performance for reasonable manufacturing errors (element magnetization direction errors ≤5°), thus yielding practical designs to improve magnetic drug targeting treatment depths. - Highlights: ► Optimization methods presented to design Halbach arrays for drug targeting. ► The goal is to maximize forces on magnetic nanoparticles at deep tissue locations. ► The presented methods yield provably globally optimal Halbach designs in 2D and 3D. ► These designs significantly outperform benchmark magnets of the same size and strength. ► These

Finding the Cell Center by a Balance of Dynein and Myosin Pulling and Microtubule Pushing: A Computational Study

Science.gov (United States)

Zhu, Jie; Burakov, Anton; Rodionov, Vladimir

2010-01-01

The centrosome position in many types of interphase cells is actively maintained in the cell center. Our previous work indicated that the centrosome is kept at the center by pulling force generated by dynein and actin flow produced by myosin contraction and that an unidentified factor that depends on microtubule dynamics destabilizes position of the centrosome. Here, we use modeling to simulate the centrosome positioning based on the idea that the balance of three forces—dyneins pulling along microtubule length, myosin-powered centripetal drag, and microtubules pushing on organelles—is responsible for the centrosome displacement. By comparing numerical predictions with centrosome behavior in wild-type and perturbed interphase cells, we rule out several plausible hypotheses about the nature of the microtubule-based force. We conclude that strong dynein- and weaker myosin-generated forces pull the microtubules inward competing with microtubule plus-ends pushing the microtubule aster outward and that the balance of these forces positions the centrosome at the cell center. The model also predicts that kinesin action could be another outward-pushing force. Simulations demonstrate that the force-balance centering mechanism is robust yet versatile. We use the experimental observations to reverse engineer the characteristic forces and centrosome mobility. PMID:20980619

The strategic ''pull'' and operational ''push'' of total quality management in UK regional electricity service companies

Energy Technology Data Exchange (ETDEWEB)

McAdam, R.; McLean, J.; Henderson, J.

2003-04-30

The aim of this paper is to evaluate whether the UK regional electricity companies (RECs) has used total quality management (TQM) as a ''push'' or as a ''pull'' change methodology. ''Push'' is the operational improvement role of TQM; ''pull'' is the strategic or direction giving, improvement role of TQM. Following the onset of privatisation in 1990 there has been evidence of the RECs adopting TQM in both ''push'' and ''pull'' methodologies with varying degrees of success. An evaluation of the change processes involved will enable improved change models to be developed leading to increased business effectiveness in this 30 billion pounds sterling industry. Other possible benefits include the possible generalisations to other utilities such as water, roads, gas and telecoms. The research methodology includes a comparative case study analysis of five RECs, which have used TQM as their overarching approach to change. One of the cases is analysed to a more in-depth level based on the multiple case findings. The findings indicate that the ''push-pull'' analysis enables the full range of TQM activities to be evaluated in the RECs studied. Overall, there is a need to have a balanced portfolio of operational or ''push''-based TQM activity that is driven by strategic or ''pull'' based TQM planning and activity. (author)

Curvature contributions to the static electrical properties of push-pull molecules

International Nuclear Information System (INIS)

Squitieri, Emilio

2005-01-01

Calculations of the curvature contribution to the diagonals components of the static dipole moment (μ), polarizability (α), first (β) and second (γ) hyperpolarizability of push-pull molecules are presented. This contribution was obtained from the analytical evaluation of electrical properties method using the harmonic zero-point energy. The valence-bond charge-transfer model was employed to obtain the field-dependent force constant and their derivates with respect to electric field. Our results show a relationship between the curvature and electronic contributions. We have also found that the curvature contribution is important in a numerical estimation of β and γ

The "Push-Pull" Approach to Fast-Track Management Development: A Case Study in Scientific Publishing

Science.gov (United States)

Fojt, Martin; Parkinson, Stephen; Peters, John; Sandelands, Eric

2008-01-01

Purpose: The purpose of this paper is to explore how a medium sized business has addressed what it has termed a "push-pull" method of management and organization development, based around an action learning approach. Design/methodology/approach: The paper sets out a methodology that other SMEs might look to replicate in their management and…

Novel family of quasi-Z-source DC/DC converters derived from current-fed push-pull converters

DEFF Research Database (Denmark)

Chub, Andrii; Husev, Oleksandr; Vinnikov, Dmitri

2014-01-01

This paper is devoted to the step-up quasi-Z-source dc/dc push-pull converter family. The topologies in the family are derived from the isolated boost converter family by replacing input inductors with the quasi-Z-source network. Two new topologies are proposed, analyzed and compared. Theoretical...

Achieving food security for one million sub-Saharan African poor through push-pull innovation by 2020.

Science.gov (United States)

Khan, Zeyaur R; Midega, Charles A O; Pittchar, Jimmy O; Murage, Alice W; Birkett, Michael A; Bruce, Toby J A; Pickett, John A

2014-04-05

Food insecurity is a chronic problem in Africa and is likely to worsen with climate change and population growth. It is largely due to poor yields of the cereal crops caused by factors including stemborer pests, striga weeds and degraded soils. A platform technology, 'push-pull', based on locally available companion plants, effectively addresses these constraints resulting in substantial grain yield increases. It involves intercropping cereal crops with a forage legume, desmodium, and planting Napier grass as a border crop. Desmodium repels stemborer moths (push), and attracts their natural enemies, while Napier grass attracts them (pull). Desmodium is very effective in suppressing striga weed while improving soil fertility through nitrogen fixation and improved organic matter content. Both companion plants provide high-value animal fodder, facilitating milk production and diversifying farmers' income sources. To extend these benefits to drier areas and ensure long-term sustainability of the technology in view of climate change, drought-tolerant trap and intercrop plants are being identified. Studies show that the locally commercial brachiaria cv mulato (trap crop) and greenleaf desmodium (intercrop) can tolerate long droughts. New on-farm field trials show that using these two companion crops in adapted push-pull technology provides effective control of stemborers and striga weeds, resulting in significant grain yield increases. Effective multi-level partnerships have been established with national agricultural research and extension systems, non-governmental organizations and other stakeholders to enhance dissemination of the technology with a goal of reaching one million farm households in the region by 2020. These will be supported by an efficient desmodium seed production and distribution system in eastern Africa, relevant policies and stakeholder training and capacity development.

Grip Force and 3D Push-Pull Force Estimation Based on sEMG and GRNN

Directory of Open Access Journals (Sweden)

Changcheng Wu

2017-06-01

Full Text Available The estimation of the grip force and the 3D push-pull force (push and pull force in the three dimension space from the electromyogram (EMG signal is of great importance in the dexterous control of the EMG prosthetic hand. In this paper, an action force estimation method which is based on the eight channels of the surface EMG (sEMG and the Generalized Regression Neural Network (GRNN is proposed to meet the requirements of the force control of the intelligent EMG prosthetic hand. Firstly, the experimental platform, the acquisition of the sEMG, the feature extraction of the sEMG and the construction of GRNN are described. Then, the multi-channels of the sEMG when the hand is moving are captured by the EMG sensors attached on eight different positions of the arm skin surface. Meanwhile, a grip force sensor and a three dimension force sensor are adopted to measure the output force of the human's hand. The characteristic matrix of the sEMG and the force signals are used to construct the GRNN. The mean absolute value and the root mean square of the estimation errors, the correlation coefficients between the actual force and the estimated force are employed to assess the accuracy of the estimation. Analysis of variance (ANOVA is also employed to test the difference of the force estimation. The experiments are implemented to verify the effectiveness of the proposed estimation method and the results show that the output force of the human's hand can be correctly estimated by using sEMG and GRNN method.

Why People Choose to Teach in Urban Schools: The Case for a Push-Pull Factor Analysis

Science.gov (United States)

Knell, Paul F.; Castro, Antonio J.

2014-01-01

This qualitative research study traces the motivations for teaching of 13 teacher candidates enrolled in an urban-based alternative certification program. After using a push-pull factor analysis, the data suggest that most participants left their previous careers due to financial shortcomings or work instability. As a result, these participants…

"Location is surprisingly a lot more important than you think": a critical thematic analysis of push and pull factor messaging used on Caribbean offshore medical school websites.

Science.gov (United States)

Morgan, Jeffrey; Crooks, Valorie A; Sampson, Carla Jackie; Snyder, Jeremy

2017-06-02

Offshore medical schools are for-profit, private enterprises located in the Caribbean that provide undergraduate medical education to students who must leave the region for postgraduate training and also typically to practice. This growing industry attracts many medical students from the US and Canada who wish to return home to practice medicine. After graduation, international medical graduates can encounter challenges obtaining residency placements and can face other barriers related to practice. We conducted a qualitative thematic analysis to discern the dominant messages found on offshore medical school websites. Dominant messages included frequent references to push and pull factors intended to encourage potential applicants to consider attending an offshore medical school. We reviewed 38 English-language Caribbean offshore medical school websites in order to extract and record content pertaining to push and pull factors. We found two push and four pull factors present across most offshore medical school websites. Push factors include the: shortages of physicians in the US and Canada that require new medical trainees; and low acceptance rates at medical schools in intended students' home countries. Pull factors include the: financial benefits of attending an offshore medical school; geographic location and environment of training in the Caribbean; training quality and effectiveness; and the potential to practice medicine in one's home country. This analysis contributes to our understanding of some of the factors behind students' decisions to attend an offshore medical school. Importantly, push and pull factors do not address the barriers faced by offshore medical school graduates in finding postgraduate residency placements and ultimately practicing elsewhere. It is clear from push and pull factors that these medical schools heavily focus messaging and marketing towards students from the US and Canada, which raises questions about who benefits from this

Combining Push Pull Tracer Tests and Microbial DNA and mRNA Analysis to Assess In-Situ Groundwater Nitrate Transformations

Science.gov (United States)

Henson, W.; Graham, W. D.; Huang, L.; Ogram, A.

2015-12-01

Nitrogen transformation mechanisms in the Upper Floridan Aquifer (UFA) are still poorly understood because of karst aquifer complexity and spatiotemporal variability in nitrate and carbon loading. Transformation rates have not been directly measured in the aquifer. This study quantifies nitrate-nitrogen transformation potential in the UFA using single well push-pull tracer injection (PPT) experiments combined with microbial characterization of extracted water via qPCR and RT-qPCR of selected nitrate reduction genes. Tracer tests with chloride and nitrate ± carbon were executed in two wells representing anoxic and oxic geochemical end members in a spring groundwater contributing area. A significant increase in number of microbes with carbon addition suggests stimulated growth. Increases in the activities of denitrification genes (nirK and nirS) as measured by RT-qPCR were not observed. However, only microbes suspended in the tracer were obtained, ignoring effects of aquifer material biofilms. Increases in nrfA mRNA and ammonia concentrations were observed, supporting Dissimilatory Reduction of Nitrate to Ammonia (DNRA) as a reduction mechanism. In the oxic aquifer, zero order nitrate loss rates ranged from 32 to 89 nmol /L*hr with no added carbon and 90 to 240 nmol /L*hr with carbon. In the anoxic aquifer, rates ranged from 18 to 95 nmol /L*hr with no added carbon and 34 to 207 nmol /L*hr with carbon. These loss rates are low; 13 orders of magnitude less than the loads applied in the contributing area each year, however they do indicate that losses can occur in oxic and anoxic aquifers with and without carbon. These rates may include, ammonia adsorption, uptake, or denitrification in aquifer material biofilms. Rates with and without carbon addition for both aquifers were similar, suggesting aquifer redox state and carbon availability alone are insufficient to predict response to nutrient additions without characterization of microbial response. Surprisingly, these

Gender differences in exerted forces and physiological load during pushing and pulling of wheeled cages by postal workers

NARCIS (Netherlands)

Van Der Beek, Allard J.; Kluver, B.D.R.; Frings-Dresen, M. H. W.; Hoozemans, M. J M

The aim was to determine gender differences regarding exerted forces and physiological load during push/pull tasks simulating the daily working practice of postal workers. Eight female and four male workers handled four-wheeled cages under eight conditions corresponding to the cage weight (130, 250,

Evaluation of a peridomestic mosquito trap for integration into an Aedes aegypti (Diptera: Culicidae) push-pull control strategy.

Science.gov (United States)

Salazar, Ferdinand V; Achee, Nicole L; Grieco, John P; Prabaripai, Atchariya; Eisen, Lars; Shah, Pankhil; Chareonviriyaphap, Theeraphap

2012-06-01

We determined the feasibility of using the BG-Sentinel™ mosquito trap (BGS) as the pull component in a push-pull strategy to reduce indoor biting by Aedes aegypti. This included evaluating varying numbers of traps (1-4) and mosquito release numbers (10, 25, 50, 100, 150, 200, and 250) on recapture rates under screen house conditions. Based on these variations in trap and mosquito numbers, release intervals were rotated through a completely randomized design with environmental factors (temperature, relative humidity, and light intensity) and monitored throughout each experiment. Data from four sampling time points (05:30, 09:30, 13:30, and 17:30) indicate a recapture range among treatments of 66-98%. Furthermore, 2-3 traps were as effective in recapturing mosquitoes as 4 traps for all mosquito release numbers. Time trends indicate Day 1 (the day the mosquitoes were released) as the "impact period" for recapture with peak numbers of marked mosquitoes collected at 09:30 or 4 h post-release. Information from this study will be used to guide the configuration of the BGS trap component of a push-pull vector control strategy currently in the proof-of-concept stage of development in Thailand and Peru. © 2012 The Society for Vector Ecology.

Push-pull with recovery stage high-voltage DC converter for PV solar generator

Science.gov (United States)

Nguyen, The Vinh; Aillerie, Michel; Petit, Pierre; Pham, Hong Thang; Vo, Thành Vinh

2017-02-01

A lot of systems are basically developed on DC-DC or DC-AC converters including electronic switches such as MOS or bipolar transistors. The limits of efficiency are quickly reached when high output voltages and high input currents are needed. This work presents a new high-efficiency-high-step-up based on push-pull DC-DC converter integrating recovery stages dedicated to smart HVDC distributed architecture in PV solar energy production systems. Appropriate duty cycle ratio assumes that the recovery stage work with parallel charge and discharge to achieve high step-up voltage gain. Besides, the voltage stress on the main switch is reduced with a passive clamp circuit and thus, low on-state resistance Rdson of the main switch can be adopted to reduce conduction losses. Thus, the efficiency of a basic DC-HVDC converter dedicated to renewable energy production can be further improved with such topology. A prototype converter is developed, and experimentally tested for validation.

Pulled Motzkin paths

International Nuclear Information System (INIS)

Janse van Rensburg, E J

2010-01-01

In this paper the models of pulled Dyck paths in Janse van Rensburg (2010 J. Phys. A: Math. Theor. 43 215001) are generalized to pulled Motzkin path models. The generating functions of pulled Motzkin paths are determined in terms of series over trinomial coefficients and the elastic response of a Motzkin path pulled at its endpoint (see Orlandini and Whittington (2004 J. Phys. A: Math. Gen. 37 5305-14)) is shown to be R(f) = 0 for forces pushing the endpoint toward the adsorbing line and R(f) = f(1 + 2cosh f))/(2sinh f) → f as f → ∞, for forces pulling the path away from the X-axis. In addition, the elastic response of a Motzkin path pulled at its midpoint is shown to be R(f) = 0 for forces pushing the midpoint toward the adsorbing line and R(f) = f(1 + 2cosh (f/2))/sinh (f/2) → 2f as f → ∞, for forces pulling the path away from the X-axis. Formal combinatorial identities arising from pulled Motzkin path models are also presented. These identities are the generalization of combinatorial identities obtained in directed paths models to their natural trinomial counterparts.

Pulled Motzkin paths

Energy Technology Data Exchange (ETDEWEB)

Janse van Rensburg, E J, E-mail: rensburg@yorku.c [Department of Mathematics and Statistics, York University, Toronto, ON, M3J 1P3 (Canada)

2010-08-20

In this paper the models of pulled Dyck paths in Janse van Rensburg (2010 J. Phys. A: Math. Theor. 43 215001) are generalized to pulled Motzkin path models. The generating functions of pulled Motzkin paths are determined in terms of series over trinomial coefficients and the elastic response of a Motzkin path pulled at its endpoint (see Orlandini and Whittington (2004 J. Phys. A: Math. Gen. 37 5305-14)) is shown to be R(f) = 0 for forces pushing the endpoint toward the adsorbing line and R(f) = f(1 + 2cosh f))/(2sinh f) {yields} f as f {yields} {infinity}, for forces pulling the path away from the X-axis. In addition, the elastic response of a Motzkin path pulled at its midpoint is shown to be R(f) = 0 for forces pushing the midpoint toward the adsorbing line and R(f) = f(1 + 2cosh (f/2))/sinh (f/2) {yields} 2f as f {yields} {infinity}, for forces pulling the path away from the X-axis. Formal combinatorial identities arising from pulled Motzkin path models are also presented. These identities are the generalization of combinatorial identities obtained in directed paths models to their natural trinomial counterparts.

Pulled Motzkin paths

Science.gov (United States)

Janse van Rensburg, E. J.

2010-08-01

In this paper the models of pulled Dyck paths in Janse van Rensburg (2010 J. Phys. A: Math. Theor. 43 215001) are generalized to pulled Motzkin path models. The generating functions of pulled Motzkin paths are determined in terms of series over trinomial coefficients and the elastic response of a Motzkin path pulled at its endpoint (see Orlandini and Whittington (2004 J. Phys. A: Math. Gen. 37 5305-14)) is shown to be R(f) = 0 for forces pushing the endpoint toward the adsorbing line and R(f) = f(1 + 2cosh f))/(2sinh f) → f as f → ∞, for forces pulling the path away from the X-axis. In addition, the elastic response of a Motzkin path pulled at its midpoint is shown to be R(f) = 0 for forces pushing the midpoint toward the adsorbing line and R(f) = f(1 + 2cosh (f/2))/sinh (f/2) → 2f as f → ∞, for forces pulling the path away from the X-axis. Formal combinatorial identities arising from pulled Motzkin path models are also presented. These identities are the generalization of combinatorial identities obtained in directed paths models to their natural trinomial counterparts.

Uranium metalla-allenes with carbene imido R_2C=U"I"V=NR' units (R=Ph_2PNSiMe_3; R'=CPh_3): alkali-metal-mediated push-pull effects with an amido auxiliary

International Nuclear Information System (INIS)

Lu, Erli; Tuna, Floriana; Kaltsoyannis, Nikolas; Liddle, Stephen T.; Lewis, William

2016-01-01

We report uranium(IV)-carbene-imido-amide metalla-allene complexes [U(BIPM"T"M"S)(NCPh_3)(NHCPh_3)(M)] (BIPM"T"M"S=C(PPh_2NSiMe_3)_2; M=Li or K) that can be described as R_2C=U=NR' push-pull metalla-allene units, as organometallic counterparts of the well-known push-pull organic allenes. The solid-state structures reveal that the R_2C=U=NR' units adopt highly unusual cis-arrangements, which are also reproduced by gas-phase theoretical studies conducted without the alkali metals to remove their potential structure-directing roles. Computational studies confirm the double-bond nature of the U=NR' and U=CR_2 interactions, the latter increasingly attenuated by potassium then lithium when compared to the hypothetical alkali-metal-free anion. Combined experimental and theoretical data show that the push-pull effect induced by the alkali metal cations and amide auxiliary gives a fundamental and tunable structural influence over the C=U"I"V=N units. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

The 'push-pull' dosimeter: When two pigments are better than one

International Nuclear Information System (INIS)

Bosi, Stephen G; Baldock, Clive; Smee, Robert

2010-01-01

A new kind of gel dosimeter (the 'push-pull' dosimeter) is proposed which would contain two spectrally complementary pigments, one which darkens with increasing dose and another which bleaches. The bleaching pigment would be optimised for high sensitivity and the darkening pigment for low sensitivity. By employing dual pigments optimised independently, the usual requisite compromises between sensitivity at low dose and accuracy at high dose would be relaxed. Such a gel, after exposure would be read using two successive optical CT scans employing two different scan wavelengths. The use of dual pigments could also reduce the occurrence of regions of high optical attenuation which generate artefacts in optical CT. This paper also presents results of simulations of the behaviour of such a gel when scanned using optical cone beam CT.

Generic, Extensible, Configurable Push-Pull Framework for Large-Scale Science Missions

Science.gov (United States)

Foster, Brian M.; Chang, Albert Y.; Freeborn, Dana J.; Crichton, Daniel J.; Woollard, David M.; Mattmann, Chris A.

2011-01-01

The push-pull framework was developed in hopes that an infrastructure would be created that could literally connect to any given remote site, and (given a set of restrictions) download files from that remote site based on those restrictions. The Cataloging and Archiving Service (CAS) has recently been re-architected and re-factored in its canonical services, including file management, workflow management, and resource management. Additionally, a generic CAS Crawling Framework was built based on motivation from Apache s open-source search engine project called Nutch. Nutch is an Apache effort to provide search engine services (akin to Google), including crawling, parsing, content analysis, and indexing. It has produced several stable software releases, and is currently used in production services at companies such as Yahoo, and at NASA's Planetary Data System. The CAS Crawling Framework supports many of the Nutch Crawler's generic services, including metadata extraction, crawling, and ingestion. However, one service that was not ported over from Nutch is a generic protocol layer service that allows the Nutch crawler to obtain content using protocol plug-ins that download content using implementations of remote protocols, such as HTTP, FTP, WinNT file system, HTTPS, etc. Such a generic protocol layer would greatly aid in the CAS Crawling Framework, as the layer would allow the framework to generically obtain content (i.e., data products) from remote sites using protocols such as FTP and others. Augmented with this capability, the Orbiting Carbon Observatory (OCO) and NPP (NPOESS Preparatory Project) Sounder PEATE (Product Evaluation and Analysis Tools Elements) would be provided with an infrastructure to support generic FTP-based pull access to remote data products, obviating the need for any specialized software outside of the context of their existing process control systems. This extensible configurable framework was created in Java, and allows the use of

A new soft switched push pull current fed converter for fuel cell applications

International Nuclear Information System (INIS)

Delshad, Majid; Farzanehfard, Hosein

2011-01-01

In this paper a new zero voltage switching current fed push pull dc-dc converter is proposed for fuel cell generation system. The auxiliary circuit in this converter, not only absorbs the voltage surge across the switches at turn off instance, but also provides zero voltage switching condition for all converter switches. Therefore, the converter efficiency is increased and size and weight of the converter can be decreased. Also implementation of control circuit is very simple since the converter is PWM controlled. In this paper, the proposed dc-dc converter operating modes are analyzed and to verify the converter operation a laboratory prototype is implemented and the experimental results are presented.

Effects of push/pull perfusion and ultrasonication on the extraction efficiencies of phthalate esters in sports drink samples using on-line hollow-fiber liquid-phase microextraction.

Science.gov (United States)

Chao, Yu-Ying; Lee, Chien-Hung; Chien, Tzu-Yang; Shih, Yu-Hsuan; Lu, Yin-An; Kuo, Ting-Hsuan; Huang, Yeou-Lih

2013-08-28

In previous studies, we developed a process, on-line ultrasound-assisted push/pull perfusion hollow-fiber liquid-phase microextraction (UA-PPP-HF-LPME), combining the techniques of push/pull perfusion (PPP) and ultrasonication with hollow-fiber liquid-phase microextraction (HF-LPME), to achieve rapid extraction of acidic phenols from water samples. In this present study, we further evaluated three more-advanced and novel effects of PPP and ultrasonication on the extraction efficiencies of neutral high-molecular-weight phthalate esters (HPAEs) in sports drinks. First, we found that inner-fiber fluid leakage occurs only in push-only perfusion-based and pull-only perfusion-based HF-LPME, but not in the PPP mode. Second, we identified a significant negative interaction between ultrasonication and temperature. Third, we found that the extraction time of the newly proposed system could be shortened by more than 93%. From an investigation of the factors affecting UA-PPP-HF-LPME, we established optimal extraction conditions and achieved acceptable on-line enrichment factors of 92-146 for HPAEs with a sampling time of just 2 min.

Eye Pull, Eye Push: Moving Objects between Large Screens and Personal Devices with Gaze and Touch

OpenAIRE

Turner , Jayson; Alexander , Jason; Bulling , Andreas; Schmidt , Dominik; Gellersen , Hans

2013-01-01

Part 4: Gaze-Enabled Interaction Design; International audience; Previous work has validated the eyes and mobile input as a viable approach for pointing at, and selecting out of reach objects. This work presents Eye Pull, Eye Push, a novel interaction concept for content transfer between public and personal devices using gaze and touch. We present three techniques that enable this interaction: Eye Cut & Paste, Eye Drag & Drop, and Eye Summon & Cast. We outline and discuss several scenarios in...

Voltage inverter with push-pull topology to inject energy into electrical systems with modulation SPWM

Directory of Open Access Journals (Sweden)

Emerson Charles M. Silva

2013-09-01

Full Text Available This paper presents a proposal for a voltage inverter topology based on push-pull converters, switched at high frequency to inject energy into the grid from a source of DC power. A system using two reverse voltage static converters provides the power grid; energy in the form of alternating current, that can work in conjunction with the provision of utility power. Aiming at the possible use of renewable energy sources, that can be stored in the form of voltage continuous, such as wind, solar, hydroelectric and others. The functioning of topology is presented, such as the power and control circuits, as well as sizing components, theoretical and practical results achieved with the assembly of a prototype 100W of power and switching in 40khz, which after filtering provides the frequency of 60Hz, which is compatible with the Brazilian electrical system.

What Makes International Capital Flows So Volatile?: Push vs. Pull Factors in the Case of Korea

Directory of Open Access Journals (Sweden)

Tae-Joon Kim

2010-12-01

Full Text Available This paper analyzes the determinants of financial capital flows in Korea, which provides an intriguing case for examining the volatility of such flows as an almost fully opened capital market. Our empirical analysis finds both pull and push factors have significantly affected all three types of foreign capital flows- foreign equity investment, foreign bond investment and foreign other-type investment- in Korea, though the relative importance of each factor varies by sample period and type of financial capital. First, the determinants of capital inflows changed substantially following the 1997 currency crisis. The impact of push factors on foreign investment strengthened, rendering the Korean stock and bond market more susceptible to external shocks. Second, the global financial crisis, which increased global financial instability and preference for safe assets, appears to have had a negative effect on other-type investment. However, fThis paper analyzes the determinants of financial capital flows in Korea, which provides an intriguing case for examining the volatility of such flows as an almost fully opened capital market. Our empirical analysis finds both pull and push factors have significantly affected all three types of foreign capital flows- foreign equity investment, foreign bond investment and foreign other-type investment- in Korea, though the relative importance of each factor varies by sample period and type of financial capital. First, the determinants of capital inflows changed substantially following the 1997 currency crisis. The impact of push factors on foreign investment strengthened, rendering the Korean stock and bond market more susceptible to external shocks. Second, the global financial crisis, which increased global financial instability and preference for safe assets, appears to have had a negative effect on other-type investment. However, foreign equity investment showed a quick recovery in the wake of global financial

Effects of Bulky Substituents of Push-Pull Porphyrins on Photovoltaic Properties of Dye-Sensitized Solar Cells.

Science.gov (United States)

Higashino, Tomohiro; Kawamoto, Kyosuke; Sugiura, Kenichi; Fujimori, Yamato; Tsuji, Yukihiro; Kurotobi, Kei; Ito, Seigo; Imahori, Hiroshi

2016-06-22

To evaluate the effects of substituent bulkiness around a porphyrin core on the photovoltaic properties of porphyrin-sensitized solar cells, long alkoxy groups were introduced at the meso-phenyl group (ZnPBAT-o-C8) and the anchoring group (ZnPBAT-o-C8Cn, n = 4, 8) of an asymmetrically substituted push-pull porphyrin with double electron-donating diarylamino groups and a single electron-withdrawing carboxyphenylethynyl anchoring group. The spectroscopic and electrochemical properties of ZnPBAT-o-C8 and ZnPBAT-o-C8Cn were found to be superior to those of a push-pull porphyrin reference (YD2-o-C8), demonstrating their excellent light-harvesting and redox properties for dye-sensitized solar cells. A power conversion efficiency (η) of the ZnPBAT-o-C8-sensitized solar cell (η = 9.1%) is higher than that of the YD2-o-C8-sensitized solar cell (η = 8.6%) using iodine-based electrolyte due to the enhanced light-harvesting ability of ZnPBAT-o-C8. In contrast, the solar cells based on ZnPBAT-o-C8Cn, possessing the additional alkoxy chains in the anchoring group, revealed the lower η values of 7.3% (n = 4) and 7.0% (n = 8). Although ZnPBAT-o-C8Cn exhibited higher resistance at the TiO2-dye-electrolyte interface by virtue of the extra alkoxy chains, the reduced amount of the porphyrins on TiO2 by excessive addition of coadsorbent chenodeoxycholic acid (CDCA) for mitigating the aggregation on TiO2 resulted in the low η values. Meanwhile, the ZnPBAT-o-C8-sensitized solar cell showed the lower η value of 8.1% than the YD2-o-C8-sensitized solar cell (η = 9.8%) using cobalt-based electrolyte. The smaller η value of the ZnPBAT-o-C8-sensitized solar cell may be attributed to the insufficient blocking effect of the bulky substituents of ZnPBAT-o-C8 under the cobalt-based electrolyte conditions. Overall, the alkoxy chain length and substitution position around the porphyrin core are important factors to affect the cell performance.

"Pull and push back" concepts of longevity and life span extension.

Science.gov (United States)

Muradian, Khachik

2013-12-01

The negative relation between metabolism and life span is a fundamental gerontological discovery well documented in a variety of ontogenetic and phylogenetic models. But how the long-lived species and populations sustain lower metabolic rate and, in more general terms, what is the efficient way to decline the metabolism? The suggested 'pull and push back' hypothesis assumes that decreased Po2 (hypoxia) and/or increased [Formula: see text] (hypercapnia) may create preconditions for the declined metabolic and aging rates. However, wider implementation of such ideas is compromised because of little advances in modification of the metabolic rate. Artificial atmosphere with controlled [Formula: see text] and [Formula: see text] could be a promising approach because of the minimal external invasions and involvement of the backward and forward loops ensuring physiological self-regulation of the metabolic perturbations. General considerations and existing data indicate that manipulations of [Formula: see text] may be more efficient in life span extension than [Formula: see text]. Thus, maximum life span of mammals positively correlates with the blood [Formula: see text] and HCO3 (-) but not with [Formula: see text]. Yet, proportional decease of the body [Formula: see text] and increase of [Formula: see text] seems the most optimal regime ensuring lower losses of the energy equivalents. Furthermore, especially rewarding results could be expected when such changes are modeled without major external invasions using the animals' inner capacity to consume O2 and generate CO2, as it is typical for the extreme longevity.

A comparison of push and pull production controls under machine breakdown

Directory of Open Access Journals (Sweden)

Prakash, J.

2011-01-01

Full Text Available Production control for high-mix production remains a complex issue. Common pull system replenishment generates large works-in-process (WIPs for each part type, especially under breakdown. This paper attempts to solve this by presenting a production control that classifies parts into two categories. The performances of three production control mechanisms under breakdown are compared. The production control mechanisms in consideration are push, shared constant WIP (CONWIP, and parallel CONWIP. A full-factorial simulation experiment was conducted. ANOVA was performed to determine the significant effects of input factors. Response surface methodology was used to demonstrate the behavior of performance measures in terms of these significant input factors. The results prove that parallel CONWIP is superior over shared CONWIP in terms of the average flow time per part. If categorical dispatch rules are employed, parallel CONWIP outperforms shared CONWIP in terms of service level. With high card count, parallel CONWIP generally produces lower bottleneck utilizations while maintaining a low average flow time per part than shared CONWIP.

Characterization and Performance Comparison of Low-Voltage, High-Speed, Push-Pull and Traveling-Wave Silicon Mach-Zehnder Modulators

Science.gov (United States)

2014-03-27

unloaded transmission line is simply the coplanar strip waveguide (CPS), and is designed to have an impedance higher than 50Ω, as the capacitive load...microwave loss operation, with a junction capacitance of 0.41 fF at 0 V bias. From a macroscopic point of view, the push-pull design uses two electrodes...by ±5°. The chip mount is designed to hold a thermoelectric cooler (TEC) between two copper plates, and a temperature sensor in the top plate, above

Determinants of FDI into Central and Eastern European Countries: Pull or Push Effect?

Directory of Open Access Journals (Sweden)

Burcak Polat

2015-11-01

Full Text Available Despite the growing interest in foreign direct investments (FDI, substantial uncertainty still exists regarding what stimulates foreign investors to operate in a foreign market and uneven distribution of FDI across countries. Using panel data for 2001 -2012 period, the major determinants of the FDI inflows into the Central and Eastern European Countries are analysed in this study. Strong evidence are found that while EU CR indices, EU and USA real GDP growth rates and global financial crisis have power to explain FDI inflows among all other push factors, labour cost, electricity price, real exchange rate and host CR indices have strong influential on FDI as the most effective pull factors. However, study fails to find any effect of openness, tax rates on commercial profits, USA CR indices, interest rate differentials and host real GDP growth on FDI.

Nonlinear Finite Element Analysis of Pull-Out Test

DEFF Research Database (Denmark)

Saabye Ottesen, N

1981-01-01

A specific pull-out test used to determine in-situ concrete compressive strength is analyzed. This test consists of a steel disc that is extracted from the structure. The finite element analysis considers cracking as well as strain hardening and softening in the pre- and post-failure region...

Uranium metalla-allenes with carbene imido R{sub 2}C=U{sup IV}=NR' units (R=Ph{sub 2}PNSiMe{sub 3}; R'=CPh{sub 3}): alkali-metal-mediated push-pull effects with an amido auxiliary

Energy Technology Data Exchange (ETDEWEB)

Lu, Erli; Tuna, Floriana; Kaltsoyannis, Nikolas; Liddle, Stephen T. [School of Chemistry, The University of Manchester (United Kingdom); Lewis, William [School of Chemistry, The University of Nottingham (United Kingdom)

2016-08-08

We report uranium(IV)-carbene-imido-amide metalla-allene complexes [U(BIPM{sup TMS})(NCPh{sub 3})(NHCPh{sub 3})(M)] (BIPM{sup TMS}=C(PPh{sub 2}NSiMe{sub 3}){sub 2}; M=Li or K) that can be described as R{sub 2}C=U=NR' push-pull metalla-allene units, as organometallic counterparts of the well-known push-pull organic allenes. The solid-state structures reveal that the R{sub 2}C=U=NR' units adopt highly unusual cis-arrangements, which are also reproduced by gas-phase theoretical studies conducted without the alkali metals to remove their potential structure-directing roles. Computational studies confirm the double-bond nature of the U=NR' and U=CR{sub 2} interactions, the latter increasingly attenuated by potassium then lithium when compared to the hypothetical alkali-metal-free anion. Combined experimental and theoretical data show that the push-pull effect induced by the alkali metal cations and amide auxiliary gives a fundamental and tunable structural influence over the C=U{sup IV}=N units. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Novel push-pull fluorescent dyes - 7-(diethylamino)furo- and thieno[3,2-c]coumarins derivatives: structure, electronic spectra and TD-DFT study

Science.gov (United States)

Akchurin, Igor O.; Yakhutina, Anna I.; Bochkov, Andrei Y.; Solovjova, Natalya P.; Medvedev, Michael G.; Traven, Valerii F.

2018-05-01

Novel push-pull fluorescent dyes - 7-(diethylamino)furo- and 7-(diethylamino)thieno[3,2-c]coumarins derivatives have been synthesized using formyl derivatives of furo- and thieno[3,2-c]coumarins as starting materials. Electron absorption and fluorescent spectra of the dyes have been recorded in different solvents. Structure and solvent effects on the dyes spectral characteristics were analyzed. The fusion of five-membered heterocycle to coumarin provides a definite increase of Stokes shifts in all solvents and results in higher quantum yields of fluorescence. The absorption and emission bands of thieno[3,2-c] coumarin derivatives are definitely shifted to the red region (3-30 nm) compared to similar derivatives of furo[3,2-c]coumarin. TD-DFT calculations of some of the studied compounds have shown that hybrid DFT functionals and adequate representation of molecular environment are essential for obtaining accurate UV-Vis absorption spectra for the dyes with extended π-system. The longest-wave electron transitions in the studied compounds were computationally shown to be of push-pull nature.

Pushed, pulled, or blocked? The elderly and the labor market in post-Soviet Russia.

Science.gov (United States)

Gerber, Theodore P; Radl, Jonas

2014-05-01

Russia provides an interesting context for studying the labor market experiences of the elderly because of its experience with market transition, its looming growth in the elderly dependency ratio, and its unusual pension policies that do not penalize pensioners for working. We use data from twenty surveys of the Russian population conducted from February 1991 to November 2007 to analyze the labor market participation and earnings of elderly Russians following market transition. Economic desperation, exacerbated by low pension levels, pushed some elderly to seek employment for income on the labor market. Elderly Russians with more education had more opportunities to work, and education differentials increased as market reforms progressed. The correlates of earnings operate similarly for retirement- and pre-retirement age Russians, with several exceptions: unobserved factors favoring employment are negatively associated with earnings for the elderly, occupation mediates most of the effects of education, and patterns of change over time differ somewhat. Elderly Russians are not disproportionately blocked from employment following market reforms. Following the initial transition shock, their labor market activity increased. Overall, both push and pull factors shape the employment and earnings of the elderly, affecting different segments of them. Copyright © 2013 Elsevier Inc. All rights reserved.

Solar cell contact pull strength as a function of pull-test temperature

Science.gov (United States)

Yasui, R. K.; Berman, P. A.

1972-01-01

Four types of solar cell contacts were given pull-strength tests at temperatures between -173 and +165 C. Contacts tested were: (1) solder-coated titanium-silver contacts on n-p cells, (2) palladium-containing titanium-silver contacts on n-p cells, (3) titanium-silver contacts on 0.2-mm-thick n-p cells, and (4) solder-coated electroless-nickel-plated contacts on p-n cells. Maximum pull strength was demonstrated at temperatures significantly below the air mass zero cell equilibrium temperature of +60 C. At the lowest temperatures, the chief failure mechanism was silicon fracture along crystallographic planes; at the highest temperatures, it was loss of solder strength. In the intermediate temperatures, many failure mechanisms operated. Pull-strength tests give a good indication of the suitability of solar cell contact systems for space use. Procedures used to maximize the validity of the results are described.

The United States and international climate cooperation: International 'pull' versus domestic 'push'

International Nuclear Information System (INIS)

Bang, Guri; Froyn, Camilla Bretteville; Hovi, Jon; Menz, Fredric C.

2007-01-01

The US government is being pressured by both international and domestic influences to re-engage in international climate control. This paper considers whether the international 'pull' and the domestic 'push' will be strong enough to accomplish this. First, we discuss whether changes in the architecture of the current climate regime might induce the United States to re-engage at the international level. We argue that the United States is unlikely to rejoin any global climate regime that is based on the Kyoto architecture, even if Kyoto were to be 'reformed'. Second, we discuss whether domestic political developments might eventually cause the United States to re-engage. We conclude that US re-engagement is likely to require the emergence of a new climate regime that basically extends US regulation to other countries. However, the forging of a unified US climate policy is still in the making. Furthermore, a new regime can gain widespread participation only if the Kyoto countries accept the idea of replacing Kyoto with some alternative architecture, which seems unlikely in the near future

The United States and international climate cooperation: international ''pull'' versus domestic ''push''

International Nuclear Information System (INIS)

Bang, G.; Froyn, C.B.; Hovi, J.; Menz, F.C.; Clarkson University, Potsdam, NY

2007-01-01

The US government is being pressured by both international and domestic influences to re-engage in international climate control. This paper considers whether the international ''pull'' and the domestic ''push'' will be strong enough to accomplish this. First, we discuss whether changes in the architecture of the current climate regime might induce the United States to re-engage at the international level. We argue that the United States is unlikely to rejoin any global climate regime that is based on the Kyoto architecture, even if Kyoto were to be ''reformed''. Second, we discuss whether domestic political developments might eventually cause the United States to re-engage. We conclude that US re-engagement is likely to require the emergence of a new climate regime that basically extends US regulation to other countries. However, the forging of a unified US climate policy is still in the making. Furthermore, a new regime can gain widespread participation only if the Kyoto countries accept the idea of replacing Kyoto with some alternative architecture, which seems unlikely in the near future. (author)

A Push-pull Protocol to Reduce Colonization of Bird Nest Boxes by Honey Bees.

Science.gov (United States)

Efstathion, Caroline A; Kern, William H

2016-09-04

Introduction of the invasive Africanized honey bee (AHB) into the Neotropics is a serious problem for many cavity nesting birds, specifically parrots. These bees select cavities that are suitable nest sites for birds, resulting in competition. The difficulty of removing bees and their defensive behavior makes a prevention protocol necessary. Here, we describe a push-pull integrated pest management protocol to deter bees from inhabiting bird boxes by applying a bird safe insecticide, permethrin, to repel bees from nest boxes, while simultaneously attracting them to pheromone-baited swarm traps. Shown here is an example experiment using Barn Owl nest boxes. This protocol successfully reduced colonization of Barn Owl nest boxes by Africanized honey bees. This protocol is flexible, allowing adjustments to accommodate a wide range of bird species and habitats. This protocol could benefit conservation efforts where AHB are located.

Organization and intramolecular charge-transfer enhancement in tripodal tris[(pyridine-4-yl)phenyl]amine push-pull molecules by intercalation into layered materials bearing acidic functionalities

Czech Academy of Sciences Publication Activity Database

Melánová, Klára; Cvejn, D.; Bureš, F.; Zima, Vítězslav; Svoboda, Jan; Beneš, L.; Mikysek, T.; Pytela, O.; Knotek, P.

2014-01-01

Roč. 43, č. 27 (2014), s. 10462-10470 ISSN 1477-9226 R&D Projects: GA ČR(CZ) GA13-01061S Institutional support: RVO:61389013 Keywords : tripodal push-pull molecules * intercalation * zirconium hydrogenphosphate Subject RIV: CA - Inorganic Chemistry Impact factor: 4.197, year: 2014

Impact of the Anchoring Ligand on Electron Injection and Recombination Dynamics at the Interface of Novel Asymmetric Push-Pull Zinc Phthalocyanines and TiO2

NARCIS (Netherlands)

Sharma, Divya; Steen, Gerrit Willem; Korterik, Jeroen P.; Garcia-Iglesias, M.; Vazquez, P; Torres, T.; Herek, Jennifer Lynn; Huijser, Jannetje Maria

2013-01-01

Phthalocyanines are promising photosensitizers for dye-sensitized solar cells (DSSCs). A parameter that has been problematic for a long time involves electron injection (EI) into the TiO2. The development of push-pull phthalocyanines shows great potential to improve the ratio of EI to back electron

On Reducing Delay in Mesh-Based P2P Streaming: A Mesh-Push Approach

Science.gov (United States)

Liu, Zheng; Xue, Kaiping; Hong, Peilin

The peer-assisted streaming paradigm has been widely employed to distribute live video data on the internet recently. In general, the mesh-based pull approach is more robust and efficient than the tree-based push approach. However, pull protocol brings about longer streaming delay, which is caused by the handshaking process of advertising buffer map message, sending request message and scheduling of the data block. In this paper, we propose a new approach, mesh-push, to address this issue. Different from the traditional pull approach, mesh-push implements block scheduling algorithm at sender side, where the block transmission is initiated by the sender rather than by the receiver. We first formulate the optimal upload bandwidth utilization problem, then present the mesh-push approach, in which a token protocol is designed to avoid block redundancy; a min-cost flow model is employed to derive the optimal scheduling for the push peer; and a push peer selection algorithm is introduced to reduce control overhead. Finally, we evaluate mesh-push through simulation, the results of which show mesh-push outperforms the pull scheduling in streaming delay, and achieves comparable delivery ratio at the same time.

Push-pull converter with energy saving circuit for protecting switching transistors from peak power stress

Science.gov (United States)

Mclyman, W. T. (Inventor)

1981-01-01

In a push-pull converter, switching transistors are protected from peak power stresses by a separate snubber circuit in parallel with each comprising a capacitor and an inductor in series, and a diode in parallel with the inductor. The diode is connected to conduct current of the same polarity as the base-emitter juction of the transistor so that energy stored in the capacitor while the transistor is switched off, to protect it against peak power stress, discharges through the inductor when the transistor is turned on, and after the capacitor is discharges through the diode. To return this energy to the power supply, or to utilize this energy in some external circuit, the inductor may be replaced by a transformer having its secondary winding connected to the power supply or to the external circuit.

Simultaneously 'pushing' and 'pulling' graphene oxide into low-polar solvents through a designed interface.

Science.gov (United States)

Liu, Zhen; Liu, Jingquan; Wang, Yichao; Razal, Joselito M; Francis, Paul S; Biggs, Mark J; Barrow, Colin J; Yang, Wenrong

2018-08-03

Dispersing graphene oxide (GO) in low-polar solvents can realize a perfect self-assembly with functional molecules and application in removal of organic impurities that only dissolve in low-polar solvents. The surface chemistry of GO plays an important role in its dispersity in these solvents. The direct transfer of hydrophilic GO into low-polar solvents, however, has remained an experimental challenge. In this study, we design an interface to transfer GO by simultaneously 'pushing and pulling' the nanosheets into low-polar solvents. Our approach is outstanding due to the ability to obtain monolayers of chemically reduced GO (CRGO) with designed surface properties in the organic phase. Using the transferred GO or CRGO dispersions, we have fabricated GO/fullerene nanocomposites and assessed the ability of CRGOs for dye adsorption. We hope our work can provide a universal approach for the phase transfer of other nanomaterials.

Beyond technology-push and demand-pull: Lessons from California's solar policy

International Nuclear Information System (INIS)

Taylor, Margaret

2008-01-01

The scale of the technological transformation required to reduce greenhouse gas emissions to 'safe' levels while minimizing economic impacts necessitates an emphasis on designing climate policy to foster, or at least not impede, environmental innovation. There is only a weak empirical base for policy-makers to stand on regarding the comparative innovation effects of various climate policy options, however. Empirical scholarship in environmental innovation is hindered by the complexity of both the innovation process and the interactions between the dual market failures of pollution and innovation that are in play, and it appears that the field would benefit from the structure provided by a common lexicon. This paper focuses on the issues related to policy categorization in this field; these issues have received little attention in the literature despite their importance to making insights gained from empirical studies generalizable. The paper reviews the origins, strengths, and weaknesses of the dominant policy typology of technology-push versus demand-pull instruments. Its primary contribution, however, is to assemble a comprehensive chronology of solar policy in California and its impacts on innovation, where known, and then use this as a basis for building a new policy categorization that takes advantage of the intuitive resonance of the dominant typology, while encompassing the broader range of policy instruments that are employed in practice in order to stimulate environmental innovation. The most noteworthy aspect of the new categorization is that it introduces a third category of environmental innovation policy instrument that focuses on improving the interface between technology suppliers and users. This reflects developments in the economics of innovation literature as well as considerable evidence in the domain of distributed solar energy technologies that opportunism by some of the actors that work at this interface can be a barrier to innovation

Functional Requirements on the Design of the Detectors and the Interaction Region of an e+e- Linear Collider with a Push-Pull Arrangement of Detectors

International Nuclear Information System (INIS)

Markiewicz, T.

2009-01-01

The Interaction Region of the International Linear Collider is based on two experimental detectors working in a push-pull mode. A time efficient implementation of this model sets specific requirements and challenges for many detector and machine systems, in particular the IR magnets, the cryogenics and the alignment system, the beamline shielding, the detector design and the overall integration. This paper attempts to separate the functional requirements of a push pull interaction region and machine detector interface from any particular conceptual or technical solution that might have been proposed to date by either the ILC Beam Delivery Group or any of the three detector concepts. As such, we hope that it provides a set of ground rules for interpreting and evaluating the MDI parts of the proposed detector concept's Letters of Intent, due March 2009. The authors of the present paper are the leaders of the IR Integration Working Group within Global Design Effort Beam Delivery System and the representatives from each detector concept submitting the Letters Of Intent.

Synthesis and pH-sensing Properties of a Push-Pull Conjugated Fluorophore Based on Dicyanomethylene-1,4-dihydropyridine

International Nuclear Information System (INIS)

Kim, Young Hyun; Kim, Heemoon; Kim, Hyung Jin

2016-01-01

A push-pull conjugated dye with a dicyanomethylene-1,4-dihydropyridine moiety (DCMP) was designed and synthesized for use as an optical pH sensor in acidic solution. The spectroscopic and pH-sensing properties of DCMP were investigated by UV-vis and fluorescence spectroscopy. DCMP displayed a pH-dependent ratiometric absorption property in the range of pH 4.5-12.0. The fluorescence intensity of DCMP around 560 nm, when irradiated at 435 nm, increased when pH was increased in the range of 2.0-7.0, showing a linear response in the pH range of 3.85-6.25.

Next-Practise in University Research Based Open Innovation - From Push to Pull: Case Studies from Denmark

DEFF Research Database (Denmark)

Rønnow Lønholdt, Jens; Wilken Bengtsson, Mille; Karlby, Lone Tolstrup

2013-01-01

-graduate education at DTU in design and management of projects in network. It supports competence development within efficient knowledge transfer. Finally conclusions and recommendations will be presented and discussed based on the above six cases within university research based knowledge transfer. © Springer......How do we ensure knowledge transfer from universities in the most effective and efficient way? What is the right balance between a push and a pull approach? These issues have been discussed at length and various methods of intermediary facilitating and ways to organise the transfer have been tried...... in different contextual settings at universities all over the world. Lessons learned are mixed and naturally varies from country to country. This paper presents a recently completed development project concerning the transfer facility at the Technical University of Denmark (DTU). The project focused...

Push-Pull Tests for Evaluating the Aerobic Cometabolism of Chlorinated Aliphatic Hydrocarbons

National Research Council Canada - National Science Library

Semprini, Lew

2006-01-01

.... This report describes a newly developed single-well technology for evaluating the feasibility of using in situ aerobic cometabolic processes to treat groundwater contaminated with chlorinated solvent mixtures...

Chemo-mechanical pushing of proteins along single-stranded DNA.

Science.gov (United States)

Sokoloski, Joshua E; Kozlov, Alexander G; Galletto, Roberto; Lohman, Timothy M

2016-05-31

Single-stranded (ss)DNA binding (SSB) proteins bind with high affinity to ssDNA generated during DNA replication, recombination, and repair; however, these SSBs must eventually be displaced from or reorganized along the ssDNA. One potential mechanism for reorganization is for an ssDNA translocase (ATP-dependent motor) to push the SSB along ssDNA. Here we use single molecule total internal reflection fluorescence microscopy to detect such pushing events. When Cy5-labeled Escherichia coli (Ec) SSB is bound to surface-immobilized 3'-Cy3-labeled ssDNA, a fluctuating FRET signal is observed, consistent with random diffusion of SSB along the ssDNA. Addition of Saccharomyces cerevisiae Pif1, a 5' to 3' ssDNA translocase, results in the appearance of isolated, irregularly spaced saw-tooth FRET spikes only in the presence of ATP. These FRET spikes result from translocase-induced directional (5' to 3') pushing of the SSB toward the 3' ssDNA end, followed by displacement of the SSB from the DNA end. Similar ATP-dependent pushing events, but in the opposite (3' to 5') direction, are observed with EcRep and EcUvrD (both 3' to 5' ssDNA translocases). Simulations indicate that these events reflect active pushing by the translocase. The ability of translocases to chemo-mechanically push heterologous SSB proteins along ssDNA provides a potential mechanism for reorganization and clearance of tightly bound SSBs from ssDNA.

Push and pull factors determing wine tourism development in the 'Tri Morave' sub-region

Directory of Open Access Journals (Sweden)

Jovanović-Tončev Melita

2016-01-01

Full Text Available The subject of this paper are the factors affecting the decision of wine tourists to take a trip to a particular destination. These factors can be divided into internal (push and external (pull factors. The purpose of this study is to determine the development potential as well as the factors that influence participation in wine tourism in Tri Morave sub-region. In order to do that, two researches were conducted: one on the offer side and another on the demand side. Based on the results of the survey on the offer side, one can conclude that Tri Morave sub-region abounds in natural and anthropological resources that should be turned into an integrated wine product. On the other hand, research concerning tourist demand was conducted by polling winery visitors. The obtained data confirms assumptions about the appearance of modern tourists seeking authentic experience, satisfaction of hedonistic needs, and enjoyment of high-quality wine and food. Based on the results of the survey, the purchase of wine and wine tasting are the highest ranked benefits that tourists expect from visits to wineries. The application of Spearman's correlation coefficient points to statistically significant correlation between respondents, who referred to tasting, wine purchase, and authentic tourist experience as the basic motives of their visit, and future behavior of tourists in terms of revisiting and recommendations of the given wine destination to friends.

Bright and photostable push-pull pyrene dye visualizes lipid order variation between plasma and intracellular membranes.

Science.gov (United States)

Niko, Yosuke; Didier, Pascal; Mely, Yves; Konishi, Gen-ichi; Klymchenko, Andrey S

2016-01-11

Imaging lipid organization in cell membranes requires advanced fluorescent probes. Here, we show that a recently synthesized push-pull pyrene (PA), similarly to popular probe Laurdan, changes the emission maximum as a function of lipid order, but outperforms it by spectroscopic properties. In addition to red-shifted absorption compatible with common 405 nm diode laser, PA shows higher brightness and much higher photostability than Laurdan in apolar membrane environments. Moreover, PA is compatible with two-photon excitation at wavelengths >800 nm, which was successfully used for ratiometric imaging of coexisting liquid ordered and disordered phases in giant unilamellar vesicles. Fluorescence confocal microscopy in Hela cells revealed that PA efficiently stains the plasma membrane and the intracellular membranes at >20-fold lower concentrations, as compared to Laurdan. Finally, ratiometric imaging using PA reveals variation of lipid order within different cellular compartments: plasma membranes are close to liquid ordered phase of model membranes composed of sphingomyelin and cholesterol, while intracellular membranes are much less ordered, matching well membranes composed of unsaturated phospholipids without cholesterol. These differences in the lipid order were confirmed by fluorescence lifetime imaging (FLIM) at the blue edge of PA emission band. PA probe constitutes thus a new powerful tool for biomembrane research.

Solvent-Dependent Dual Fluorescence of the Push-Pull System 2-Diethylamino-7-Nitrofluorene

KAUST Repository

Larsen, Martin A. B.

2018-01-31

The solvent-dependent excited state behavior of the molecular push-pull system 2-diethylamino-7-nitrofluorene has been explored using femtosecond transient absorption spectroscopy in combination with density functional theory calculations. Several excited state minima have been identified computationally, all possessing significant intramolecular charge transfer character. The experimentally observed dual fluorescence is suggested to arise from a planar excited state minimum and another minimum reached by twisting of the aryl-nitrogen bond of the amino group. The majority of the excited state population, however, undergo non-radiative transitions and potential excited deactivation pathways are assessed in the computational investigation. A third excited state conformer, characterized by twisting around the aryl-nitrogen bond of the nitro group, is reasoned to be responsible for the majority of the non-radiative decays and a crossing between the excited state and ground state is localized. Additionally, ultrafast intersystem crossing is observed in the apolar solvent cyclohexane and rationalized to occur via an El-Sayed assisted transition from one of the identified excited state minima. The solvent thus determines more than just the fluorescence lifetime and shapes the potential energy landscape, thereby dictating the available excited state pathways.

Solvent-Dependent Dual Fluorescence of the Push-Pull System 2-Diethylamino-7-Nitrofluorene

KAUST Repository

Larsen, Martin A. B.; Stephansen, Anne B.; Alarousu, Erkki; Pittelkow, Michael; Mohammed, Omar F.; Sø lling, Theis I

2018-01-01

The solvent-dependent excited state behavior of the molecular push-pull system 2-diethylamino-7-nitrofluorene has been explored using femtosecond transient absorption spectroscopy in combination with density functional theory calculations. Several excited state minima have been identified computationally, all possessing significant intramolecular charge transfer character. The experimentally observed dual fluorescence is suggested to arise from a planar excited state minimum and another minimum reached by twisting of the aryl-nitrogen bond of the amino group. The majority of the excited state population, however, undergo non-radiative transitions and potential excited deactivation pathways are assessed in the computational investigation. A third excited state conformer, characterized by twisting around the aryl-nitrogen bond of the nitro group, is reasoned to be responsible for the majority of the non-radiative decays and a crossing between the excited state and ground state is localized. Additionally, ultrafast intersystem crossing is observed in the apolar solvent cyclohexane and rationalized to occur via an El-Sayed assisted transition from one of the identified excited state minima. The solvent thus determines more than just the fluorescence lifetime and shapes the potential energy landscape, thereby dictating the available excited state pathways.

Pull-push mechanism for the 1,2-hydrogen rearrangement of carbenes. Substituent and deuterium isotope effects for thermal decomposition of 1-phenyl-2-diazopropanes

International Nuclear Information System (INIS)

Su, D.T.T.; Thornton, E.R.

1978-01-01

Intramolecular and intermolecular deuterium isotope effects have been measured for the thermal carbene H rearrangements of three substituted 1-phenyl-2-diazopropanes-1-d in hexane at 25 0 C. The isotope effects, k/sub H//k/sub D/, vary from ca. 1.2 to 1.5, increasing with electron-withdrawing substituents, for the formation of both cis- and trans-β-methylstyrenes. Product ratios were determined for these compounds as well as the corresponding undeuterated ones, permitting calculation of intermolecular primary and secondary isotope effects. In addition, the competition among the cis and trans products and the product of H migration from the terminal methyl group permitted determination of Hammett rho values of ca. -1 for the competition between benzylic and terminal migration. The results strongly indicate a ''pull-push'' mechanism, which can be pictured roughly as electrophilic attack on the C--H bond by the phantom p orbital of the carbene along with backside nucleophilic attack by the carbene unshared electron pair to push the H away and form the π bond. The data are believed to be consistent only with a nonzero barrier for the carbene hydrogen rearrangement

Non-paraxial beam to push and pull microparticles

DEFF Research Database (Denmark)

Novitsky, Andrey; Qiu, C.-W.

2011-01-01

We discuss a feasibility of the pulling (backward) force acting on a spherical microparticle in a non-paraxial Bessel beam. The effect can be explained by the strong interaction of particle's multipoles or by the conservation of momentum in the system “photons-particle.” It is remarkable that the...

Pushed news: when the news comes to the cellphone

Directory of Open Access Journals (Sweden)

Antonio Fidalgo

2009-12-01

Full Text Available Combining two findings of recent surveys on the Internet which state that 1 “the Internet will soon surpass all other media as a main source for national and international news” and 2 “the mobile device will be the primary connection tool to the Internet in 2020” leads us to the conclusion that smartphones will soon be the primary source for news access. But if so, how will news come to the Internetconnected cellphones? In accordance with the distinction, already drawn in 1997, between push and pull technologies as two different forms of how content is delivered to the end users, cellphones are characterized as push devices (passive reception, in opposition to computers, classified as pull devices (active reception. The news items that fit cellphones are pushed news. And they will be pushed as SMS, e-mails, tweets and through news aggregators.

PUSHED NEWS: When the news comes to the cellphone

Directory of Open Access Journals (Sweden)

Antonio Fidalgo

2009-12-01

Full Text Available Combining two findings of recent surveys on the Internet whichstate that 1 “the Internet will soon surpass all other media as a main source for national and international news” and 2 “the mobile device will be the primary connection tool to the Internet in 2020” leads us to the conclusion that smartphones will soon be the primary source for news access. But if so, how will news come to the Internetconnected cellphones? In accordance with the distinction, already drawn in 1997, between push and pull technologies as two different forms of how content is delivered to the end users, cellphones are characterized as push devices (passive reception, in opposition to computers, classified as pull devices (active reception. The news items that fit cellphones are pushed news. And they will be pushed as SMS, e-mails, tweets and through news aggregators.

Cavity Pull Rod: Device to Promote Single Crystal Growth from the Melt

Science.gov (United States)

Goldsby, Jon (Inventor)

2017-01-01

A pull rod for use in producing a single crystal from a molten alloy is provided that includes an elongated rod having a first end and a second end, a first cavity defined at the first end and a second cavity defined at the first end and in communication with the first cavity. The first cavity receives the molten alloy and the second cavity vents a gas from the molten alloy to thereby template a single crystal when the pull rod is dipped into and extracted from the molten alloy.

Cyclic deformation behaviour of quenched and tempered 42CrMo4 (AISI 4140) at two-block push-pull-loading; Zum Wechselverformungsverhalten von verguetetem 42CrMo4 bei zweistufiger Zug-Druck-Beanspruchung

Energy Technology Data Exchange (ETDEWEB)

Schulze, V. [Karlsruhe Univ. (T.H.) (Germany). Inst. fuer Werkstoffkunde 1; Lang, K.-H.; Voehringer, O.; Macherauch, E.

1998-11-01

The behaviour of steels in the course of two- and multi-block cyclic loading has been investigated up to now almost exclusively regarding the fatigue life. According to this, only a few papers exist, dealing with the cyclic deformation behaviour at two- and multi-block-push-pull-loading. Therefore, in stress- and total strain-controlled experiments with a single change of the amplitude (two-block-experiments) and multiple changes between two blocks of different lengths and amplitudes (multi-block-experiments) the cyclic deformation processes have been investigated for the quenched and tempered steel grade 42 CrMo 4 (equivalent to AISI 4140). Using the data of stress- and strain-Woehler-curves determined in usual fatigue tests, damages defined according to Miner`s rule were adjoined to the blocks. The Miner-damages at failure observed in the two-block-experiments with changes from high to low amplitudes were smaller than one and at inverse changes of amplitudes larger than one. In contrast to this, in multi-block-experiments no universally valid correlations were observed between the Miner-damages at failure and the test-parameters applied. At all tests cyclic work-softening was observed as in single-step-experiments. However, work-softening processes at high amplitude loadings yield to much larger plastic strain amplitudes after changing to smaller amplitudes than in single-step tests. Contrarily, in multi-block-tests work-softening at higher amplitude loadings reduces with decreasing block-length and increasing portion of the blocks with the smaller amplitude. This is attributed to effects of static strain-ageing. Total-strain-controlled two-block cyclic deformation experiments yield to similar effects as in stress-controlled tests. 18 refs.

An on-line push/pull perfusion-based hollow-fiber liquid-phase microextraction system for high-performance liquid chromatographic determination of alkylphenols in water samples.

Science.gov (United States)

Chao, Yu-Ying; Jian, Zhi-Xuan; Tu, Yi-Ming; Wang, Hsaio-Wen; Huang, Yeou-Lih

2013-06-07

In this study, we employed a novel on-line method, push/pull perfusion hollow-fiber liquid-phase microextraction (PPP-HF-LPME), to extract 4-tert-butylphenol, 2,4-di-tert-butylphenol, 4-n-nonylphenol, and 4-n-octylphenol from river and tap water samples; we then separated and quantified the extracted analytes through high-performance liquid chromatography (HPLC). Using this approach, we overcame the problem of fluid loss across the porous HF membrane to the donor phase, permitting on-line coupling of HF-LPME to HPLC. In our PPP-HF-LPME system, we used a push/pull syringe pump as the driving source to perfuse the acceptor phase, while employing a heating mantle and an ultrasonic probe to accelerate mass transfer. We optimized the experimental conditions such as the nature of the HF supported intermediary phase and the acceptor phase, the composition of the donor and acceptor phases, the sample temperature, and the sonication conditions. Our proposed method provided relative standard deviations of 3.1-6.2%, coefficients of determination (r(2)) of 0.9989-0.9998, and limits of detection of 0.03-0.2 ng mL(-1) for the analytes under the optimized conditions. When we applied this method to analyses of river and tap water samples, our results confirmed that this microextraction technique allows reliable monitoring of alkylphenols in water samples.

Photoinduced Charge Shifts and Electron Transfer in Viologen-Tetraphenylborate Complexes: Push-Pull Character of the Exciplex.

Science.gov (United States)

Santos, Willy G; Budkina, Darya S; Deflon, Victor M; Tarnovsky, Alexander N; Cardoso, Daniel R; Forbes, Malcolm D E

2017-06-14

Viologen-tetraarylborate ion-pair complexes were prepared and investigated by steady-state and time-resolved spectroscopic techniques such as fluorescence and femtosecond transient absorption. The results highlight a charge transfer transition that leads to changes in the viologen structure in the excited singlet state. Femtosecond transient absorption reveals the formation of excited-state absorption and stimulated emission bands assigned to the planar (k obs < 10 12 s -1 ) and twisted (k obs ∼ 10 10 s -1 ) structures between two pyridinium groups in the viologen ion. An efficient photoinduced electron transfer from the tetraphenylborate anionic moiety to the viologen dication was observed less than 1 μs after excitation. This is a consequence of the push-pull character of the electron donor twisted viologen structure, which helps formation of the borate triplet state. The borate triplet state is deactivated further via a second electron transfer process, generating viologen cation radical (V •+ ).

No-Drain Single Incision Liposuction Pull-Through Technique for Gynecomastia.

Science.gov (United States)

Khalil, Ashraf A; Ibrahim, Amr; Afifi, Ahmed M

2017-04-01

Several different methods have been proposed for treatment of gynecomastia, depending on the amount of breast enlargement and skin redundancy. The liposuction pull-through technique has been proposed as an efficacious treatment for many gynecomastia cases. This work aims to study the outcome of this technique when applied as an outpatient procedure, without the use of drains and through a single incision. Fifty-two patients with bilateral gynecomastia without significant skin excess were included in this study. The liposuction pull-through technique was performed through a single incision just above the inframammary fold and without the use of drains. Patients were followed up for 6 months. The proposed technique was able to treat the gynecomastia in all patients, with a revision rate of 1.9% to remove residual glandular tissues. There were no seromas, hematomas, nipple distortion, permanent affection of nipple sensation or wound healing problems. The liposuction pull-through technique is an effective treatment for gynecomastia without significant skin redundancy. It combines the benefits of the direct excision of glandular tissues, with the minimally invasive nature of liposuction. Performing the procedure through a single incision without the use of drains and without general anesthesia is a safe alternative. This journal requires that authors assign a level of evidence to each article. For a full description of these Evidence-Based Medicine ratings, please refer to the Table of Contents or the online Instructions to Authors http://www.springer.com/00266 .

Pushing Back against Push-In: ESOL Teacher Resistance and the Complexities of Coteaching

Science.gov (United States)

McClure, Greg; Cahnmann-Taylor, Melisa

2010-01-01

As U. S. school districts struggle to address persistent achievement gaps between increasing numbers of English language learners (ELLs) and their native-English-speaking counterparts, many districts are moving away from segregative models like pull-out to implement more collaborative approaches such as coteaching, or push-in. In contrast to…

Structural Change Out of Agriculture: Labor Push versus Labor Pull

OpenAIRE

Francisco Alvarez-Cuadrado; Markus Poschke

2011-01-01

The process of economic development is characterized by substantial rural-urban migrations and a decreasing share of agriculture in output and employment. The literature highlights two main engines behind this process of structural change: (i) improvements in agricultural technology combined with the effect of Engel's law of demand push resources out of the agricultural sector (the "labor push" hypothesis), and (ii) improvements in industrial technology attract labor into this sector (the "la...

Push and pull models to manage patient consent and licensing of multimedia resources in digital repositories for case-based reasoning.

Science.gov (United States)

Kononowicz, Andrzej A; Zary, Nabil; Davies, David; Heid, Jörn; Woodham, Luke; Hege, Inga

2011-01-01

Patient consents for distribution of multimedia constitute a significant element of medical case-based repositories in medicine. A technical challenge is posed by the right of patients to withdraw permission to disseminate their images or videos. A technical mechanism for spreading information about changes in multimedia usage licenses is sought. The authors gained their experience by developing and managing a large (>340 cases) repository of virtual patients within the European project eViP. The solution for dissemination of license status should reuse and extend existing metadata standards in medical education. Two methods: PUSH and PULL are described differing in the moment of update and the division of responsibilities between parties in the learning object exchange process. The authors recommend usage of the PUSH scenario because it is better adapted to legal requirements in many countries. It needs to be stressed that the solution is based on mutual trust of the exchange partners and therefore is most appropriate for use in educational alliances and consortia. It is hoped that the proposed models for exchanging consents and licensing information will become a crucial part of the technical frameworks for building case-based repositories.

Evaluating Upper-Body Strength and Power From a Single Test: The Ballistic Push-up.

Science.gov (United States)

Wang, Ran; Hoffman, Jay R; Sadres, Eliahu; Bartolomei, Sandro; Muddle, Tyler W D; Fukuda, David H; Stout, Jeffrey R

2017-05-01

Wang, R, Hoffman, JR, Sadres, E, Bartolomei, S, Muddle, TWD, Fukuda, DH, and Stout, JR. Evaluating upper-body strength and power from a single test: the ballistic push-up. J Strength Cond Res 31(5): 1338-1345, 2017-The purpose of this study was to examine the reliability of the ballistic push-up (BPU) exercise and to develop a prediction model for both maximal strength (1 repetition maximum [1RM]) in the bench press exercise and upper-body power. Sixty recreationally active men completed a 1RM bench press and 2 BPU assessments in 3 separate testing sessions. Peak and mean force, peak and mean rate of force development, net impulse, peak velocity, flight time, and peak and mean power were determined. Intraclass correlation coefficients were used to examine the reliability of the BPU. Stepwise linear regression was used to develop 1RM bench press and power prediction equations. Intraclass correlation coefficient's ranged from 0.849 to 0.971 for the BPU measurements. Multiple regression analysis provided the following 1RM bench press prediction equation: 1RM = 0.31 × Mean Force - 1.64 × Body Mass + 0.70 (R = 0.837, standard error of the estimate [SEE] = 11 kg); time-based power prediction equation: Peak Power = 11.0 × Body Mass + 2012.3 × Flight Time - 338.0 (R = 0.658, SEE = 150 W), Mean Power = 6.7 × Body Mass + 1004.4 × Flight Time - 224.6 (R = 0.664, SEE = 82 W); and velocity-based power prediction equation: Peak Power = 8.1 × Body Mass + 818.6 × Peak Velocity - 762.0 (R = 0.797, SEE = 115 W); Mean Power = 5.2 × Body Mass + 435.9 × Peak Velocity - 467.7 (R = 0.838, SEE = 57 W). The BPU is a reliable test for both upper-body strength and power. Results indicate that the mean force generated from the BPU can be used to predict 1RM bench press, whereas peak velocity and flight time measured during the BPU can be used to predict upper-body power. These findings support the potential use of the BPU as a valid method to evaluate upper-body strength and power.

The United States and international climate cooperation: International 'pull' versus domestic 'push'

Energy Technology Data Exchange (ETDEWEB)

Bang, Guri [Center for International Climate and Environmental Research, Oslo (Norway); Froyn, Camilla Bretteville [Center for International Climate and Environmental Research, Oslo (Norway); Hovi, Jon [Center for International Climate and Environmental Research, Oslo (Norway) and Department of Political Science, University of Oslo, P.O. Box 1097, 0317 Oslo (Norway)]. E-mail: jon.hovi@stv.uio.no; Menz, Fredric C. [Center for International Climate and Environmental Research, Oslo (Norway); School of Business, Clarkson University, Potsdam, NY 13699 (United States)

2007-02-15

The US government is being pressured by both international and domestic influences to re-engage in international climate control. This paper considers whether the international 'pull' and the domestic 'push' will be strong enough to accomplish this. First, we discuss whether changes in the architecture of the current climate regime might induce the United States to re-engage at the international level. We argue that the United States is unlikely to rejoin any global climate regime that is based on the Kyoto architecture, even if Kyoto were to be 'reformed'. Second, we discuss whether domestic political developments might eventually cause the United States to re-engage. We conclude that US re-engagement is likely to require the emergence of a new climate regime that basically extends US regulation to other countries. However, the forging of a unified US climate policy is still in the making. Furthermore, a new regime can gain widespread participation only if the Kyoto countries accept the idea of replacing Kyoto with some alternative architecture, which seems unlikely in the near future.

Single-molecule pull-down (SiMPull) for new-age biochemistry: methodology and biochemical applications of single-molecule pull-down (SiMPull) for probing biomolecular interactions in crude cell extracts.

Science.gov (United States)

Aggarwal, Vasudha; Ha, Taekjip

2014-11-01

Macromolecular interactions play a central role in many biological processes. Protein-protein interactions have mostly been studied by co-immunoprecipitation, which cannot provide quantitative information on all possible molecular connections present in the complex. We will review a new approach that allows cellular proteins and biomolecular complexes to be studied in real-time at the single-molecule level. This technique is called single-molecule pull-down (SiMPull), because it integrates principles of conventional immunoprecipitation with the powerful single-molecule fluorescence microscopy. SiMPull is used to count how many of each protein is present in the physiological complexes found in cytosol and membranes. Concurrently, it serves as a single-molecule biochemical tool to perform functional studies on the pulled-down proteins. In this review, we will focus on the detailed methodology of SiMPull, its salient features and a wide range of biological applications in comparison with other biosensing tools. © 2014 WILEY Periodicals, Inc.

Report on ignitability testing of ''no-flow'' push bit

International Nuclear Information System (INIS)

Witwer, K.S.

1997-01-01

Testing was done to determine if an ignition occurs during a sixty foot drop of a Universal Sampler onto a push-mode bit in a flammable gas environment. Ten drops each of the sampler using both a push-mode and rotary mode insert onto a push-mode bit were completed. No ignition occurred during any of the drops

Customized Pull Systems for Single-Product Flow Lines

NARCIS (Netherlands)

Gaury, E.G.A.; Kleijnen, J.P.C.; Pierreval, H.

1998-01-01

Traditionally pull production systems are managed through classic control systems such as Kanban, Conwip, or Base stock, but this paper proposes ‘customized’ pull control. Customization means that a given production line is managed through a pull control system that in principle connects each stage

Minimizing pulling geometry errors in atomic force microscope single molecule force spectroscopy.

Science.gov (United States)

Rivera, Monica; Lee, Whasil; Ke, Changhong; Marszalek, Piotr E; Cole, Daniel G; Clark, Robert L

2008-10-01

In atomic force microscopy-based single molecule force spectroscopy (AFM-SMFS), it is assumed that the pulling angle is negligible and that the force applied to the molecule is equivalent to the force measured by the instrument. Recent studies, however, have indicated that the pulling geometry errors can drastically alter the measured force-extension relationship of molecules. Here we describe a software-based alignment method that repositions the cantilever such that it is located directly above the molecule's substrate attachment site. By aligning the applied force with the measurement axis, the molecule is no longer undergoing combined loading, and the full force can be measured by the cantilever. Simulations and experimental results verify the ability of the alignment program to minimize pulling geometry errors in AFM-SMFS studies.

Low-Back Biomechanics and Static Stability During Isometric Pushing

Science.gov (United States)

Granata, Kevin P.; Bennett, Bradford C.

2006-01-01

Pushing and pulling tasks are increasingly prevalent in industrial workplaces. Few studies have investigated low-back biomechanical risk factors associated with pushing, and we are aware of none that has quantified spinal stability during pushing exertions. Data recorded from 11 healthy participants performing isometric pushing exertions demonstrated that trunk posture, vector force direction of the applied load, and trunk moment were influenced (p pushing task, and foot position. A biomechanical model was used to analyze the posture and hand force data gathered from the pushing exertions. Model results indicate that pushing exertions provide significantly (p pushing exertions. If one maintains stability by means of cocontraction, additional spinal load is thereby created, increasing the risk of overload injury. Thus it is important to consider muscle cocontraction when evaluating the biomechanics of pushing exertions. Potential applications of this research include improved assessment of biomechanical risk factors for the design of industrial pushing tasks. PMID:16435695

Silicon Nitride Deposition for Flexible Organic Electronic Devices by VHF (162 MHz)-PECVD Using a Multi-Tile Push-Pull Plasma Source.

Science.gov (United States)

Kim, Ki Seok; Kim, Ki Hyun; Ji, You Jin; Park, Jin Woo; Shin, Jae Hee; Ellingboe, Albert Rogers; Yeom, Geun Young

2017-10-19

Depositing a barrier film for moisture protection without damage at a low temperature is one of the most important steps for organic-based electronic devices. In this study, the authors investigated depositing thin, high-quality SiN x film on organic-based electronic devices, specifically, very high-frequency (162 MHz) plasma-enhanced chemical vapor deposition (VHF-PECVD) using a multi-tile push-pull plasma source with a gas mixture of NH 3 /SiH 4 at a low temperature of 80 °C. The thin deposited SiN x film exhibited excellent properties in the stoichiometry, chemical bonding, stress, and step coverage. Thin film quality and plasma damage were investigated by the water vapor transmission rate (WVTR) and by electrical characteristics of organic light-emitting diode (OLED) devices deposited with SiN x , respectively. The thin deposited SiN x film exhibited a low WVTR of 4.39 × 10 -4  g (m 2 · day) -1 for a single thin (430 nm thick) film SiN x and the electrical characteristics of OLED devices before and after the thin SiN x film deposition on the devices did not change, which indicated no electrical damage during the deposition of SiN x on the OLED device.

Analysis of the behavior of orthogonal-core-type push-pull parametric transformer with iron and copper losses. Tetsuson oyobi doson wo koryoshita chokko jishinkei push pull parametric hen prime atsuki no dosa kaiseki

Energy Technology Data Exchange (ETDEWEB)

Tajima, K; Anazawa, Y; Kaga, A [Akita University, Akita (Japan). Mining College; Ichinokura, O [Tohoku University, Sendai (Japan). Faculty of Engineering

1991-04-30

This paper reports on a precise numerical analysis of operating characteristics of the push-pull parametric transformer of orthogonal-core type (proposed by the authors in the preceding papers) made in consideration of both the iron loss of its magnetic core and the copper loss of its windings. A model of magnetic circuit in the core is presented, which involves magnetic reluctances representing saturation characteristics of the core and magnetic inductances representing effects produced by hysteresis. Use is made of the function that expresses the saturation characteristics by a twenty-first power series of magnetic flux, the coefficient of each term being determined by use of experimental data on a specified sample of the magnetic core. Furthermore, recourse is had to the circuit simulator SPICE in order to analyze the operating characteristics of the transformer. Comparing results of the present analysis with experimental results, the following are noted: first, both output voltages and currents of windings of the transformer under the condition of parametric oscillation are calculated with sufficient accuracy; second, the present analysis is capable of evaluating the conversion efficiency of electric power and input power factor of the transformer, and of providing more accurate values of both voltage and current in the case of the maximum output under loading conditions as compared with the analyses so far presented. 8 refs., 11 figs., 2 tabs.

Friction Pull Plug Welding in Aluminum Alloys

Science.gov (United States)

Brooke, Shane A.; Bradford, Vann

2012-01-01

NASA's Marshall Space Flight Center (MSFC) has recently invested much time and effort into the process development of Friction Pull Plug Welding (FPPW). FPPW, is a welding process similar to Friction Push Plug Welding in that, there is a small rotating part (plug) being spun and simultaneously pulled (forged) into a larger part. These two processes differ, in that push plug welding requires an internal reaction support, while pull plug welding reacts to the load externally. FPPW was originally conceived as a post proof repair technique for the Space Shuttle fs External Tank. FPPW was easily selected as the primary weld process used to close out the termination hole on the Constellation Program's ARES I Upper Stage circumferential Self-Reacting Friction Stir Welds (SR-FSW). The versatility of FPPW allows it to also be used as a repair technique for both SR-FSW and Conventional Friction Stir Welds. To date, all MSFC led development has been concentrated on aluminum alloys (2195, 2219, and 2014). Much work has been done to fully understand and characterize the process's limitations. A heavy emphasis has been spent on plug design, to match the various weldland thicknesses and alloy combinations. This presentation will summarize these development efforts including weld parameter development, process control, parameter sensitivity studies, plug repair techniques, material properties including tensile, fracture and failure analysis.

Dual-functional Memory and Threshold Resistive Switching Based on the Push-Pull Mechanism of Oxygen Ions

KAUST Repository

Huang, Yi-Jen

2016-04-07

The combination of nonvolatile memory switching and volatile threshold switching functions of transition metal oxides in crossbar memory arrays is of great potential for replacing charge-based flash memory in very-large-scale integration. Here, we show that the resistive switching material structure, (amorphous TiOx)/(Ag nanoparticles)/(polycrystalline TiOx), fabricated on the textured-FTO substrate with ITO as the top electrode exhibits both the memory switching and threshold switching functions. When the device is used for resistive switching, it is forming-free for resistive memory applications with low operation voltage (<±1 V) and self-compliance to current up to 50 μA. When it is used for threshold switching, the low threshold current is beneficial for improving the device selectivity. The variation of oxygen distribution measured by energy dispersive X-ray spectroscopy and scanning transmission electron microscopy indicates the formation or rupture of conducting filaments in the device at different resistance states. It is therefore suggested that the push and pull actions of oxygen ions in the amorphous TiOx and polycrystalline TiOx films during the voltage sweep account for the memory switching and threshold switching properties in the device.

Push-Pull Tests for Evaluating the Aerobic Cometabolism of Chlorinated Aliphatic Hydrocarbons: Cost & Performance Report

National Research Council Canada - National Science Library

Semprini, Lew

2006-01-01

.... This report describes a newly developed single-well technology for evaluating the feasibility of using in situ aerobic cometabolic processes to treat groundwater contaminated with chlorinated solvent mixtures...

Pushing, pulling and electromagnetic radiation force cloaking by a pair of conducting cylindrical particles

Science.gov (United States)

Mitri, F. G.

2018-02-01

The present analysis shows that two conducting cylindrical particles illuminated by an axially-polarized electric field of plane progressive waves at arbitrary incidence will attract, repel or become totally cloaked (i.e., invisible to the transfer of linear momentum carried by the incident waves), depending on their sizes, the interparticle distance as well as the angle of incidence of the incident field. Based on the rigorous multipole expansion method and the translational addition theorem of cylindrical wave functions, the electromagnetic (EM) radiation forces arising from multiple scattering effects between a pair of perfectly conducting cylindrical particles of circular cross-sections are derived and computed. An effective incident field on a particular particle is determined first, and used subsequently with its corresponding scattered field to derive the closed-form analytical expressions for the radiation force vector components. The mathematical expressions for the EM radiation force components (i.e. longitudinal and transverse) are exact, and have been formulated in partial-wave series expansions in cylindrical coordinates involving the angle of incidence, the interparticle distance and the expansion coefficients. Numerical examples illustrate the analysis for two perfectly conducting circular cylinders in a homogeneous nonmagnetic medium of wave propagation. The computations for the dimensionless radiation force functions are performed with particular emphasis on varying the angle of incidence, the interparticle distance, and the sizes of the particles. Depending on the interparticle distance and angle of incidence, the cylinders yield total neutrality (or invisibility); they experience no force and become unresponsive to the transfer of the EM linear momentum due to multiple scattering cancellation effects. Moreover, pushing or pulling EM forces between the two cylinders arise depending on the interparticle distance, the angle of incidence and their

Attentional Push: Augmenting Salience with Shared Attention Modeling

OpenAIRE

Gorji, Siavash; Clark, James J.

2016-01-01

We present a novel visual attention tracking technique based on Shared Attention modeling. Our proposed method models the viewer as a participant in the activity occurring in the scene. We go beyond image salience and instead of only computing the power of an image region to pull attention to it, we also consider the strength with which other regions of the image push attention to the region in question. We use the term Attentional Push to refer to the power of image regions to direct and man...

Assesing tree-root & soil interaction using pull-out test apparatus

Science.gov (United States)

Wibowo, J.; Corcoran, M. K.; Kala, R.; Leavell, D.

2011-12-01

. When the test begins the load cell and displacement transducers immediately started recording the measurements, and the measurements are stored on a laptop computer. The hydraulic pump controls the rate of loading for a relatively slow pulling displacement rate of 0.08 in./sec. Failure occurred when the root breaks or was pulled out of the soil. Maximum forces and root failure location were noted, as well as any additional observations during and after the test. In the ERDC tests, root diameters (root with bark) ranged between 0.7 and 2.33 in., the pullout force was between 86 and 3513 lb, and the pullout stress was between 56 and 2645 psi. ERDC recorded three different types of tree-root failures: pure root tensile failure, bonding between root and soil failure, and a combination of the two. In tensile failure, a root breaks abruptly and the force versus displacement curve usually shows a steep slope, and there is no residual strength. In a bonding failure, the force versus displacement curve shows a gentler slope, and there is residual strength. A combined failure mode may also occur. For pullout tests conducted for the ERDC research, the combined mode failure was the most prevalent failure mechanism.

Cohesive Zone Model Based Numerical Analysis of Steel-Concrete Composite Structure Push-Out Tests

Directory of Open Access Journals (Sweden)

J. P. Lin

2014-01-01

Full Text Available Push-out tests were widely used to determine the shear bearing capacity and shear stiffness of shear connectors in steel-concrete composite structures. The finite element method was one efficient alternative to push-out testing. This paper focused on a simulation analysis of the interface between concrete slabs and steel girder flanges as well as the interface of the shear connectors and the surrounding concrete. A cohesive zone model was used to simulate the tangential sliding and normal separation of the interfaces. Then, a zero-thickness cohesive element was implemented via the user-defined element subroutine UEL in the software ABAQUS, and a multiple broken line mode was used to define the constitutive relations of the cohesive zone. A three-dimensional numerical analysis model was established for push-out testing to analyze the load-displacement curves of the push-out test process, interface relative displacement, and interface stress distribution. This method was found to accurately calculate the shear capacity and shear stiffness of shear connectors. The numerical results showed that the multiple broken lines mode cohesive zone model could describe the nonlinear mechanical behavior of the interface between steel and concrete and that a discontinuous deformation numerical simulation could be implemented.

RATE-DEPENDENT PULL-OUT BEARING CAPACITY OF PILES BY SIMILITUDE MODEL TESTS USING SEEPAGE FORCE

Science.gov (United States)

Kato, Tatsuya; Kokusho, Takaji

Pull-out test of model piles was conducted by varying the pull-out velocity and skin friction of piles using a seepage force similitude model test apparatus. Due to the seepage consolidation under the pressure of 150kPa, the effective stress distribution in a prototype saturated soil of 17m could be successfully reproduced in the model ground of 28cm thick, in which the pull-out tests were carried out. The pull-out load rose to a peak value at small displacement, and then decreased to a residual value. At the same time, pore pressure in the vicinity of the pile decreased due to suction near the tip and the positive dilatancy near the pile skin. The maximum pull-out load, pile axial load, side friction and the corresponding displacement increased dramatically with increasing pull-out velocity. It was found that these rate-dependent trends become more prominent with increasing skin friction.

Ambiguity in measuring matrix diffusion with single-well injection/recovery tracer tests

Science.gov (United States)

Lessoff, S.C.; Konikow, Leonard F.

1997-01-01

Single-well injection/recovery tracer tests are considered for use in characterizing and quantifying matrix diffusion in dual-porosity aquifers. Numerical modeling indicates that neither regional drift in homogeneous aquifers, nor heterogeneity in aquifers having no regional drift, nor hydrodynamic dispersion significantly affects these tests. However, when drift is coupled simultaneously with heterogeneity, they can have significant confounding effects on tracer return. This synergistic effect of drift and heterogeneity may help explain irreversible flow and inconsistent results sometimes encountered in previous single-well injection/recovery tracer tests. Numerical results indicate that in a hypothetical single-well injection/recovery tracer test designed to demonstrate and measure dual-porosity characteristics in a fractured dolomite, the simultaneous effects of drift and heterogeneity sometimes yields responses similar to those anticipated in a homogeneous dual-porosity formation. In these cases, tracer recovery could provide a false indication of the occurrence of matrix diffusion. Shortening the shut-in period between injection and recovery periods may make the test less sensitive to drift. Using multiple tracers having different diffusion characteristics, multiple tests having different pumping schedules, and testing the formation at more than one location would decrease the ambiguity in the interpretation of test data.

Predicting Bobsled Pushing Ability from Various Combine Testing Events.

Science.gov (United States)

Tomasevicz, Curtis L; Ransone, Jack W; Bach, Christopher W

2018-03-12

The requisite combination of speed, power, and strength necessary for a bobsled push athlete coupled with the difficulty in directly measuring pushing ability makes selecting effective push crews challenging. Current practices by USA Bobsled and Skeleton (USABS) utilize field combine testing to assess and identify specifically selected performance variables in an attempt to best predict push performance abilities. Combine data consisting of 11 physical performance variables were collected from 75 subjects across two winter Olympic qualification years (2009 and 2013). These variables were sprints of 15-, 30-, and 60 m, a flying 30 m sprint, a standing broad jump, a shot toss, squat, power clean, body mass, and dry-land brake and side bobsled pushes. Discriminant Analysis (DA) in addition to Principle Component Analysis (PCA) was used to investigate two cases (Case 1: Olympians vs. non-Olympians; Case 2: National Team vs. non-National Team). Using these 11 variables, DA led to a classification rule that proved capable of identifying Olympians from non-Olympians and National Team members from non-National Team members with 9.33% and 14.67% misclassification rates, respectively. The PCA was used to find similar test variables within the combine that provided redundant or useless data. After eliminating the unnecessary variables, DA on the new combinations showed that 8 (Case 1) and 20 (Case 2) other combinations with fewer performance variables yielded misclassification rates as low as 6.67% and 13.33% respectively. Utilizing fewer performance variables can allow governing bodies in many other sports to create more appropriate combine testing that maximize accuracy, while minimizing irrelevant and redundant strategies.

Push or Pull: Changes in the Relative Risk and Growth of Entrepreneurship Among Older Households.

Science.gov (United States)

Weller, Christian E; Wenger, Jeffrey B; Lichtenstein, Benyamin; Arcand, Carolyn

2018-03-19

Amid insufficient retirement savings and the growing need to work longer, it is important to understand why self-employment, especially entrepreneurship, has grown among older households. Older households may have been pushed into entrepreneurship by the growing risks of wage-and-salary employment as wages and jobs have become less stable. Alternatively, older households may have been pulled into entrepreneurship as the associated risks have declined, for instance, due to greater opportunities to diversify income away from risky business income. We examine the economic causes of the rise in entrepreneurship among older households. We use summary statistics and multinomial logit regressions to analyze the link between economic pressures in wage-and-salary employment, financial strength of entrepreneurship, and the presence and change of entrepreneurship among older households-aged 50 years or older. We use household data from the Federal Reserve's Survey of Consumer Finances from 1989 to 2013. We find little support for the claim that increased economic pressures are correlated with rising entrepreneurship. Instead, our results suggest that the growth of older entrepreneurship is coincident with increasing access to dividend and interest income. We also find some evidence that access to Social Security and other annuity benefits increases the likelihood of self-employment. Implications: Entrepreneurship among older households increasingly correlates with income diversification. Policymakers interested in encouraging more entrepreneurship among older households could consider increased access to income diversification through social insurance.

The Determination of Production and Distribution Policy in Push-Pull Production Chain with Supply Hub as the Junction Point

Science.gov (United States)

Sinaga, A. T.; Wangsaputra, R.

2018-03-01

The development of technology causes the needs of products and services become increasingly complex, diverse, and fluctuating. This causes the level of inter-company dependencies within a production chains increased. To be able to compete, efficiency improvements need to be done collaboratively in the production chain network. One of the efforts to increase efficiency is to harmonize production and distribution activities in the production chain network. This paper describes the harmonization of production and distribution activities by applying the use of push-pull system and supply hub in the production chain between two companies. The research methodology begins with conducting empirical and literature studies, formulating research questions, developing mathematical models, conducting trials and analyses, and taking conclusions. The relationship between the two companies is described in the MINLP mathematical model with the total cost of production chain as the objective function. Decisions generated by the mathematical models are the size of production lot, size of delivery lot, number of kanban, frequency of delivery, and the number of understock and overstock lot.

Azo polymers with electronical push and pull structures prepared via RAFT polymerization and its photoinduced birefringence behavior

Directory of Open Access Journals (Sweden)

2008-08-01

Full Text Available Two methacrylate monomers containing azo and electronical push and pull structure, e.g. 2-Methyl-acrylic-acid-2-{[4-(4-cyano-phenylazo-3-methyl-phenyl]-ethyl-amino-ethyl ester (MACP with cyano substituted and 2-Methylacrylic-acid-2-{ethyl-[4-(4-methoxy-phenylazo-3-methyl-phenyl]-amino}-ethyl ester (MAMP with methoxy substituted, were synthesized and polymerized using 2-cyanoprop-2-yl dithiobenzoate (CPDB as chain transfer agent and 2,2'-azobisisobutyronitrile (AIBN as initiator. The results showed that the polymerization displayed characteristics of ‘living’/controlled free radical polymerization. Thus, the obtained polymers, polyMACP (pMACP and polyMAMP (pMAMP, had controlled molecular weights and narrow molecular weights distribution. The chain extension experiments of pMACP and pMAMP using styrene as the second monomer were successfully carried out. The photo-induced trans-cis-trans isomerization kinetic of pMACP and pMAMP in chloroform solution were described. Marked differences in rate for the trans-cis and cis-trans isomerization of pMACP and pMAMP were observed in chloroform solution due to the different electronic effects in these two polymers. Photoinduced birefringence and surface relief grating (SRG of the pMACP and pMAMP were investigated in thin film state.

The push–pull tactic for mitigation of mountain pine beetle (Coleoptera: Curculionidae) damage in lodgepole and whitebark pines

Science.gov (United States)

Nancy E. Gillette; Constance J. Mehmel; Sylvia R. Mori; Jeffrey N. Webster; David L. Wood; Nadir Erbilgin; Donald R. Owen

2012-01-01

In an attempt to improve semiochemical-based treatments for protecting forest stands from bark beetle attack, we compared push-pull versus push-only tactics for protecting lodgepole pine (Pinus contorta Douglas ex Loudon) and whitebark pine (Pinus albicaulis Engelm.) stands from attack by mountain pine beetle (...

Full-field fabric stress mapping by micro Raman spectroscopy in a yarn push-out test.

Science.gov (United States)

Lei, Z K; Qin, F Y; Fang, Q C; Bai, R X; Qiu, W; Chen, X

2018-02-01

The full-field stress distribution of a two-dimensional plain fabric was mapped using micro Raman spectroscopy (MRS) through a novel yarn push-out test, simulating a quasi-static projectile impact on the fabric. The stress-strain relationship for a single yarn was established using a digital image correlation method in a single-yarn tensile test. The relationship between Raman peak shift and aramid Kevlar 49 yarn stress was established using MRS in a single-yarn tensile test. An out-of-plane loading test was conducted on an aramid Kevlar 49 plain fabric, and the yarn stress was measured using MRS. From the full-field fabric stress distribution, it can be observed that there is a cross-shaped distribution of high yarn stress; this result would be helpful in further studies on load transfer on a fabric during a projectile impact.

Single well surfactant test to evaluate surfactant floods using multi tracer method

Science.gov (United States)

Sheely, Clyde Q.

1979-01-01

Data useful for evaluating the effectiveness of or designing an enhanced recovery process said process involving mobilizing and moving hydrocarbons through a hydrocarbon bearing subterranean formation from an injection well to a production well by injecting a mobilizing fluid into the injection well, comprising (a) determining hydrocarbon saturation in a volume in the formation near a well bore penetrating formation, (b) injecting sufficient mobilizing fluid to mobilize and move hydrocarbons from a volume in the formation near the well bore, and (c) determining the hydrocarbon saturation in a volume including at least a part of the volume of (b) by an improved single well surfactant method comprising injecting 2 or more slugs of water containing the primary tracer separated by water slugs containing no primary tracer. Alternatively, the plurality of ester tracers can be injected in a single slug said tracers penetrating varying distances into the formation wherein the esters have different partition coefficients and essentially equal reaction times. The single well tracer method employed is disclosed in U.S. Pat. No. 3,623,842. This method designated the single well surfactant test (SWST) is useful for evaluating the effect of surfactant floods, polymer floods, carbon dioxide floods, micellar floods, caustic floods and the like in subterranean formations in much less time and at much reduced cost compared to conventional multiwell pilot tests.

Electromigration of single metal atoms observed by scanning tunneling microscopy

NARCIS (Netherlands)

Braun, K.-F.; Soe, W.H.; Flipse, C.F.J.

2007-01-01

The authors show in this letter that single metal atoms on a Ni(111) surface can be pushed by electromigration forces from a scanning tunneling microscope tip. This repulsive interaction is obsd. over a length scale of 6 nm. While for voltages above -300 mV the atoms are pulled by the microscope

Single fiber push-out characterization of interfacial mechanical properties in unidirectional CVI-C/SiC composites by the nano-indentation technique

Science.gov (United States)

Zhang, Lifeng; Ren, Chengzu; Zhou, Changling; Xu, Hongzhao; Jin, Xinmin

2015-12-01

The characterization of interfaces in woven ceramic matrix composites is one of the most challenging problems in composite application. In this investigation, a new model material consisting of the chemical vapor infiltration unidirectional C/SiC composites with PyC fiber coating were prepared and evaluated to predict the interfacial mechanic properties of woven composites. Single fiber push-out/push-back tests with the Berkovich indenter were conducted on the thin sliced specimens using nano-indentation technique. To give a detailed illustration of the interfacial crack propagation and failure mechanism, each sector during the push-out process was analyzed at length. The test results show that there is no detectable difference between testing a fiber in a direct vicinity to an already tested fiber and testing a fiber in vicinity to not-pushed fibers. Moreover, the interface debonding and fiber sliding mainly occur at the PyC coating, and both the fiber and surrounding matrix have no plastic deformation throughout the process. Obtained from the load-displacement curve, the interfacial debonding strength (IDS) and friction stress (IFS) amount to, respectively, 35 ± 5 MPa and 10 ± 1 MPa. Based on the findings, the interfacial properties with PyC fiber coating can be predicted. Furthermore, it is expected to provide a useful guideline for the design, evaluation and optimal application of CVI-C/SiC.

Physical Limits on the Precision of Mitotic Spindle Positioning by Microtubule Pushing forces: Mechanics of mitotic spindle positioning.

Science.gov (United States)

Howard, Jonathon; Garzon-Coral, Carlos

2017-11-01

Tissues are shaped and patterned by mechanical and chemical processes. A key mechanical process is the positioning of the mitotic spindle, which determines the size and location of the daughter cells within the tissue. Recent force and position-fluctuation measurements indicate that pushing forces, mediated by the polymerization of astral microtubules against- the cell cortex, maintain the mitotic spindle at the cell center in Caenorhabditis elegans embryos. The magnitude of the centering forces suggests that the physical limit on the accuracy and precision of this centering mechanism is determined by the number of pushing microtubules rather than by thermally driven fluctuations. In cells that divide asymmetrically, anti-centering, pulling forces generated by cortically located dyneins, in conjunction with microtubule depolymerization, oppose the pushing forces to drive spindle displacements away from the center. Thus, a balance of centering pushing forces and anti-centering pulling forces localize the mitotic spindles within dividing C. elegans cells. © 2017 The Authors. BioEssays published by Wiley Periodicals, Inc.

Intrapartum translabial ultrasound with pushing used to predict the difficulty in vacuum-assisted delivery of fetuses in non-occiput posterior position.

Science.gov (United States)

Antonio Sainz, José; Borrero, Carlota; Aquise, Adriana; García-Mejido, José Antonio; Gutierrez, Laura; Fernández-Palacín, Ana

2016-10-01

Our aim is to evaluate the capacity of intrapartum translabial ultrasound (ITU) with pushing in the prediction of difficulty of fetal extraction in vacuum assisted deliveries. Prospective, observational study performed (2/2015-8/2015) on 75 nulliparous women, ≥37 weeks with singleton pregnancies at full dilatation who had ITU-with-pushing performed, previous to vacuum-placement for fetal extraction. Working on the translabial sagittal-plane, we assessed: Angle-Progression (AoP), Progression-Distance (PD) and Head-Direction (HD); in the axial plane we evaluated: Midline-Angle (MLA) and Head-Perineum-Distance (HPD). Vacuum extractions were classified as easy-difficulty (ED) (≤3 vacuum-pulls), difficult-unsuccessful (DD) (>3 vacuum-pulls). We did not assess occipito-posterior-presentations. Seventy nulliparous were studied (44-ED,26-DD). We observed no differences in obstetric, neonatal or intrapartum characteristics between the two study groups, with the following exceptions: newborn weight (3272 ± 438 g versus 3540 ± 372 g; p = 0.011) and number of vacuum-pulls (1.4-ED-vs-4.4-DD; p pushing was 143.9° ± 14.6° in ED and 115.1°± 12.9° in DD (p Pushing was 42.7 ± 11.3 mm versus 30.4 ± 9.8 mm (p Pushing was 27.6°± 26.6° versus 57.5°±26.5°(p=0.025); HPD-Pushing was 40.8 ± 10.0 mm versus 47.4 ± 10.9 mm (p = 0.039). We identified that the presence of an AoP-Pushing > 128° predicts an Easy-Vacuum-Delivery (≤3 Vacuum-Pulls) in  >85% of cases (Sen 80%-FPR 9.3%).

Comparison of bond strength of different endodontic sealers to root dentin: An in vitro push-out test.

Science.gov (United States)

Madhuri, G Vijaya; Varri, Sujana; Bolla, Nagesh; Mandava, Pragna; Akkala, Lakshmi Swathi; Shaik, Jaheer

2016-01-01

To compare the bond strength of four different endodontic sealers to root dentin through push-out test design. Forty single-rooted teeth with completely formed apices were selected. Teeth were decoronated, and working length was determined. Instrumentation and irrigation were performed. The teeth were divided into four groups based upon the sealer used. Group 1: Bioceramic sealer (Endosequence), Group 2: Mineral trioxide aggregate (MTA) based sealer (MTA Fill apex), Group 3: Epoxy resin based sealer (MM-Seal), and Group 4: Dual cure resin-based sealer (Hybrid Root Seal). Manipulation and application of the sealer was done as per the manufacturer instructions. All the teeth were obturated using 6% gutta-percha. After obturation, each tooth was prepared for push-out test with root slices of 2 mm thickness using universal testing machine. The highest bond strength was found in Group 1 (Endosequence) (P strength was found in Group 2 (MTA Fill apex). Statistical analysis is done by two-way ANOVA and Newman-Keuls multiple post hoc. The push-out bond strength of Bioceramic sealer was highest followed by resin-based sealer and lowest bond strength was observed in MTA-based sealer.

Push-out strength of modified Portland cements and resins.

Science.gov (United States)

Iacono, Francesco; Gandolfi, Maria Giovanna; Huffman, Bradford; Sword, Jeremy; Agee, Kelli; Siboni, Francesco; Tay, Franklin; Prati, Carlo; Pashley, David

2010-02-01

Modified calcium-silicate cements derived from white Portland cement (PC) were formulated to test their push-out strength from radicular dentin after immersion for 1 month. Slabs obtained from 42 single-rooted extracted teeth were prepared with 0.6 mm diameter holes, then enlarged with rotary instruments. After immersion in EDTA and NaOC1, the holes were filled with modified PCs or ProRoot MTA, Vitrebond and Clearfil SE. Different concentrations of phyllosilicate (montmorillonite-MMT) were added to experimental cements. ProRoot MTA was also included as reference material. Vitrebond and Clearfil SE were included as controls. Each group was tested after 1 month of immersion in water or PBS. A thin-slice push-out test on a universal testing machine served to test the push-out strength of materials. Results were statistically analyzed using the least squares means (LSM) method. The modified PCs had push-out strengths of 3-9.5 MPa after 1 month of immersion in water, while ProRoot MTA had 4.8 MPa. The push-out strength of PC fell after incubation in PBS for 1 month, while the push-out strength of ProRoot MTA increased. There were no significant changes in Clearfil SE Bond or Vitrebond after water or PBS storage.

Characterization of Direct Push Vadose Zone Sediments from the 241-U Single-Shell Tank Farm

Energy Technology Data Exchange (ETDEWEB)

Brown, Christopher F.; Valenta, Michelle M.; Serne, R. Jeffrey; Bjornstad, Bruce N.; Lanigan, David C.; Iovin, Cristian; Clayton, Ray E.; Geiszler, Keith N.; Clayton, Eric T.; Kutnyakov, Igor V.; Baum, Steven R.; Lindberg, Michael J.; Orr, Robert D.

2007-12-20

The overall goals of the Tank Farm Vadose Zone Project, led by CH2M HILL Hanford Group, Inc., are 1) to define risks from past and future single-shell tank farm activities, 2) to identify and evaluate the efficacy of interim measures, and 3) to aid, via collection of geochemical information and data, the future decisions that must be made by the U.S. Department of Energy (DOE) regarding the near-term operations, future waste retrieval, and final closure activities for the single-shell tank Waste Management Areas (WMAs). For a more complete discussion of the goals of the Tank Farm Vadose Zone Project, see the overall work plan, Phase 1 RCRA Facility Investigation/Corrective Measures Study Work Plan for the Single-Shell Tank Waste Management Areas (DOE 1999). Specific details on the rationale for activities performed at WMA U are found in Crumpler (2003). To meet these goals, CH2M HILL Hanford Group, Inc., asked scientists from Pacific Northwest National Laboratory (PNNL) to perform detailed analyses of vadose zone sediment collected within the U Single-Shell Tank Farm. Specifically, this report contains all the geochemical and selected physical characterization data collected on vadose zone sediment recovered from ten direct push characterization holes emplaced to investigate vadose zone contamination associated with potential leaks within the 241-U Single-Shell Tank Farm. Specific tanks targeted during this characterization campaign included tanks 241-U-104/241-U-105, 241-U-110, and 241-U-112. Additionally, this report compiles data from direct push samples collected north of tank 241-U-201, as well as sediment collected from the background borehole (C3393). After evaluating all the characterization and analytical data, there is no question that the vadose zone in the vicinity of tanks 241-U-104 and 241-U-105 has been contaminated by tank-related waste. This observation is not new, as gamma logging of drywells in the area has identified uranium contamination at the

[Design on tester of pull-out force for orthodontic micro implant].

Science.gov (United States)

Su, He; Wu, Pei; Wang, Huiyuan; Chen, Yan; Bao, Xuemei

2013-09-01

A special device for measuring the pull-out force of orthodontic micro implant was designed, which has the characteristics of simple construction and easy operation, and can be used to detect the pull-out-force of orthodontic micro implant. The tested data was stored and analyzed by a computer, and as the results, the pull-out-force curve, maximum pull-out force as well as average pull-out force were outputted, which was applied in analyzing or investigating the initial stability and immediate loading property of orthodontic micro implant.

Discussion on well field technology for acid in-situ leaching of uranium at a deposit of Yining uranium mine

International Nuclear Information System (INIS)

Ye Shandong; Wu Yunhui; Yin Guifang

2005-01-01

The characteristics of geology and hydrogeology of a uranium deposit, the make-up and use of lixiviant, equilibrium control of push-pull, improvement of air lift efficiency, layout of well net, and management of well construction are described. (authors)

Special considerations for testing rising rotating stem MOVs

International Nuclear Information System (INIS)

Moffa, A.

1992-01-01

Rising stem gate and globe valves have one plane of motion: linear. The stem is either pushed or pulled into position. For rising and rotating stems however, there are two planes of motion: linear and rotational. The stem is twisted in addition to being pushed or pulled into position. Typical motor operated valve (MOV) sizing equations account only for the linear requirements of the valve to open or close. Theoretical calculations performed for a two-dimensional system predict that in the running load region, rotational torque requirements far exceed the linear requirements. To validate the theoretical model, torque testing of rising rotating stem valves was preformed, using Liberty Technologies Valve Operation Test and Evaluation System (VOTES). Theoretical and empirical data have produced a new perspective for operational requirements and a guideline for testing rising rotating stem valves

USE OF NARROW-DIAMETER DIRECT-PUSH WELLS TO CHARACTERIZE AND REMEDIATE CARBON TETRACHLORIDE IN THE 200 WEST AREA HANFORD SITE, WASHINGTON

International Nuclear Information System (INIS)

Rohay, V.J.

2009-01-01

This single page graphic shows several figures. The Hydraulic Hammer Rig (HHR) direct-push technology has been successfully used to characterize carbon tetrachloride in the vadose zone. Based on their favorable performance and radius of influence, HHR SVE wells have potential for future use in both monitoring and targeted SVE to achieve VOC cleanup goals at the carbon tetrachloride waste sites

Morphisms of Extensions of C*-algebras: Pushing Forward the Busby Invariant

DEFF Research Database (Denmark)

Eilers, Søren; Loring, Terry A.; Pedersen, Gert Kjærgård

1999-01-01

of varying severity, on the given vertical maps and describe the solutions in terms of push-outs and pull-backs of certain diagrams. Our characterization of the universal solution to one of the diagrams yields a concrete description of various amalgamated free products. This leads to new results about the K...

A New Kind of Single-Well Tracer Test for Assessing Subsurface Heterogeneity

Science.gov (United States)

Hansen, S. K.; Vesselinov, V. V.; Lu, Z.; Reimus, P. W.; Katzman, D.

2017-12-01

Single-well injection-withdrawal (SWIW) tracer tests have historically been interpreted using the idealized assumption of tracer path reversibility (i.e., negligible background flow), with background flow due to natural hydraulic gradient being an un-modeled confounding factor. However, we have recently discovered that it is possible to use background flow to our advantage to extract additional information about the subsurface. To wit: we have developed a new kind of single-well tracer test that exploits flow due to natural gradient to estimate the variance of the log hydraulic conductivity field of a heterogeneous aquifer. The test methodology involves injection under forced gradient and withdrawal under natural gradient, and makes use of a relationship, discovered using a large-scale Monte Carlo study and machine learning techniques, between power law breakthrough curve tail exponent and log-hydraulic conductivity variance. We will discuss how we performed the computational study and derived this relationship and then show an application example in which our new single-well tracer test interpretation scheme was applied to estimation of heterogeneity of a formation at the chromium contamination site at Los Alamos National Laboratory. Detailed core hole records exist at the same site, from which it was possible to estimate the log hydraulic conductivity variance using a Kozeny-Carman relation. The variances estimated using our new tracer test methodology and estimated by direct inspection of core were nearly identical, corroborating the new methodology. Assessment of aquifer heterogeneity is of critical importance to deployment of amendments associated with in-situ remediation strategies, since permeability contrasts potentially reduce the interaction between amendment and contaminant. Our new tracer test provides an easy way to obtain this information.

Choices of Destination for Transnational Higher Education: "Pull" Factors in an Asia Pacific Market

Science.gov (United States)

Ahmad, Syed Zamberi; Buchanan, Frederick Robert

2016-01-01

Traditional assumptions favouring native English language countries in transnational higher education (TNHE) overlook experiences of international students in new emerging Asian education hubs. Specifically, there has been limited research relating to international students' choice for studying in Malaysia. Drawing from the "push-pull"…

Tubular bending and pull-out forces in high-curvature well bores

International Nuclear Information System (INIS)

Dareing, D.W.; Ahlers, C.A.

1991-01-01

This paper is concerned with drag forces developed on tubulars in high-curvature well bores typically found in drainhole and horizontal drilling. The dog-leg severity of these types of boreholes are considerably higher than those typically found in conventional directional drilling. The objective of the study was to determine the significance of bending stiffness on drag forces in the pull-out mode. The method of analysis treats the tubular as a multi-spanned curved beam under tension and solves for radial displacements, slope, shear and bending moment over each span. Calculations show that bending stiffness is a minor factor provided there are no locally severe dog legs superimposed in the high-curvature well bore

Push-out tests and evaluation of FRP perfobond rib shear connectors performance

Science.gov (United States)

Kolpasky, Ludvik; Ryjacek, Pavel

2017-09-01

The behavioural characteristics of FRP (fibre-reinforced polymer) perfobond rib shear connector was examined through push-out tests in order to verify the applicability for pedestrian bridge structure. The aim of this study is to determine interaction between high performance concrete slab and handmade FRP plate which represent web of the composite beam. Combination of these modern materials leads to structural system with both great load bearing capacity and also sufficient flexural stiffness of the composite element. Openings cut into the GFRP plate at a variable spacing allow GFRP reinforcement bars to be inserted to act as shear studs. Hand lay-up process can increase suitable properties of FRP for connection by perfobond rib shear connectors. In this study, three push-out tests on fiber-reinforced polymer were performed to investigate their shear behaviour. The results of the push-out tests on FRP perfobond rib shear connector indicates great promise for application in full scale structures.

Fecal incontinence after single-stage Soave's pull-through ...

African Journals Online (AJOL)

Journal Home > Vol 8, No 1 (2012) > ... Demographic, clinical data, preoperative investigations, operative records, postoperative ... Keywords: fecal continence, Hirschsprung's disease, Soave's operation, transanal endorectal pull-through ...

Shoulder joint loading and posture during medicine cart pushing task.

Science.gov (United States)

Xu, Xu; Lin, Jia-Hua; Boyer, Jon

2013-01-01

Excessive physical loads and awkward shoulder postures during pushing and pulling are risk factors for shoulder pain. Pushing a medicine cart is a major component of a work shift for nurses and medical assistants in hospitals and other health care facilities. A laboratory experiment was conducted to examine the effects of common factors (e.g., lane congestion, cart load stability, floor surface friction) on shoulder joint moment and shoulder elevation angle of participants during cart pushing. Participants pushed a medicine cart on straight tracks and turning around right-angle corners. Peak shoulder joint moments reached 25.1 Nm, 20.3 Nm, and 26.8 Nm for initial, transition, and turning phases of the pushing tasks, indicating that shoulder joint loading while pushing a medical cart is comparable to levels previously reported from heavy manual activities encountered in industry (e.g., garbage collection). Also, except for user experience, all other main study factors, including congestion level, cart load stability, location of transition strip, shoulder tendency, surface friction, and handedness, significantly influenced shoulder joint moment and shoulder elevation angle. The findings provide a better understanding of shoulder exposures associated with medicine cart operations and may be helpful in designing and optimizing the physical environment where medicine carts are used.

New devices for measuring forces on the kayak foot bar and on the seat during flat-water kayak paddling: a technical report.

Science.gov (United States)

Nilsson, Johnny E; Rosdahl, Hans G

2014-03-01

The purpose was to develop and validate portable force-measurement devices for recording push and pull forces applied by each foot to the foot bar of a kayak and the horizontal force at the seat. A foot plate on a single-point force transducer mounted on the kayak foot bar underneath each foot allowed the push and pull forces to be recorded. Two metal frames interconnected with 4 linear ball bearings, and a force transducer allowed recording of horizontal seat force. The foot-bar-force device was calibrated by loading each foot plate with weights in the push-pull direction perpendicular to the foot plate surface, while the seat-force device was calibrated to horizontal forces with and without weights on the seat. A strong linearity (r2 = .99-1.0) was found between transducer output signal and load force in the push and pull directions for both foot-bar transducers perpendicular to the foot plate and the seat-force-measuring device. Reliability of both devices was tested by means of a test-retest design. The coefficient of variation (CV) for foot-bar push and pull forces ranged from 0.1% to 1.1%, and the CV for the seat forces varied from 0.6% to 2.2%. The current study opens up a field for new investigations of the forces generated in the kayak and ways to optimize kayak-paddling performance.

A revisit to self-excited push pull vacuum tube radio frequency oscillator for ion sources and power measurements

International Nuclear Information System (INIS)

Hlondo, L. R.; Lalremruata, B.; Punte, L. R. M.; Rebecca, L.; Lalnunthari, J.; Thanga, H. H.

2016-01-01

Self-excited push-pull vacuum tube oscillator is one of the most commonly used oscillators in radio frequency (RF)-ion plasma sources for generation of ions using radio frequency. However, in spite of its fundamental role in the process of plasma formation, the working and operational characteristics are the most frequently skip part in the descriptions of RF ion sources in literatures. A more detailed treatment is given in the present work on the RF oscillator alone using twin beam power tetrodes 829B and GI30. The circuit operates at 102 MHz, and the oscillation conditions, stability in frequency, and RF output power are studied and analyzed. A modified form of photometric method and RF peak voltage detection method are employed to study the variation of the oscillator output power with plate voltage. The power curves obtained from these measurements are quadratic in nature and increase with increase in plate voltage. However, the RF output power as measured by photometric methods is always less than the value calculated from peak voltage measurements. This difference is due to the fact that the filament coil of the ordinary light bulb used as load/detector in photometric method is not a perfect inductor. The effect of inductive reactance on power transfer to load was further investigated and a technique is developed to estimate the amount of power correction needed in the photometric measurement result.

Push-Pull Type Porphyrin Based Sensitizers: The Effect of Donor Structure on the Light-Harvesting Ability and Photovoltaic Performance

KAUST Repository

Qi, Qingbiao; Li, Renzhi; Luo, Jie; Zheng, Bin; Huang, Kuo-Wei; Wang, Peng; Wu, Jishan

2015-01-01

Push-pull type porphyrin-based sensitizers have become promising candidates for high-efficiency dye sensitized solar cells (DSCs). It is of importance to understand the fundamental structure-physical property-photovoltaic performance relationships by varying the donor and acceptor moieties. In this work, two new porphyrin-based sensitizers, WW-7 and WW-8, were synthesized and compared with the known sensitizer YD20. All the three dyes have the same porphyrin core and acceptor group (ethynylbenzoic acid) but their donor groups vary from the triphenylamine in YD20 to meso-diphenylaminoanthracene in WW-7 to N-phenyl carbazole in WW-8. Co(II/III)-based DSC device characterizations revealed that WW-7 showed enhanced light harvesting ability in comparison to YD20 with improved incident photon-to-collected electron conversion efficiencies (IPCEs). As a result, WW-7 displayed much higher short circuit current (Jsc: 13.54 mA cm-2) and open-circuit voltage (Voc: 0.829 V), with a power conversion efficiency (η) as high as 7.7%. Under the same conditions, YD20 cell exhibited a power conversion efficiency of 6.6% and the dye WW-8 showed even lower efficiency (η = 4.6%). Detailed physical measurements and theoretic calculations were conducted to understand the difference and reveal how three different donor structures affect their molecular orbital profile, light-harvesting ability, energy level alignment, and eventually the photovoltaic performance.

Push-Pull Type Porphyrin Based Sensitizers: The Effect of Donor Structure on the Light-Harvesting Ability and Photovoltaic Performance

KAUST Repository

Qi, Qingbiao

2015-06-23

Push-pull type porphyrin-based sensitizers have become promising candidates for high-efficiency dye sensitized solar cells (DSCs). It is of importance to understand the fundamental structure-physical property-photovoltaic performance relationships by varying the donor and acceptor moieties. In this work, two new porphyrin-based sensitizers, WW-7 and WW-8, were synthesized and compared with the known sensitizer YD20. All the three dyes have the same porphyrin core and acceptor group (ethynylbenzoic acid) but their donor groups vary from the triphenylamine in YD20 to meso-diphenylaminoanthracene in WW-7 to N-phenyl carbazole in WW-8. Co(II/III)-based DSC device characterizations revealed that WW-7 showed enhanced light harvesting ability in comparison to YD20 with improved incident photon-to-collected electron conversion efficiencies (IPCEs). As a result, WW-7 displayed much higher short circuit current (Jsc: 13.54 mA cm-2) and open-circuit voltage (Voc: 0.829 V), with a power conversion efficiency (η) as high as 7.7%. Under the same conditions, YD20 cell exhibited a power conversion efficiency of 6.6% and the dye WW-8 showed even lower efficiency (η = 4.6%). Detailed physical measurements and theoretic calculations were conducted to understand the difference and reveal how three different donor structures affect their molecular orbital profile, light-harvesting ability, energy level alignment, and eventually the photovoltaic performance.

Cyclic biomechanical testing of biocomposite lateral row knotless anchors in a human cadaveric model.

Science.gov (United States)

Barber, F Alan; Bava, Eric D; Spenciner, David B; Piccirillo, Justin

2013-06-01

The purpose of this study was to assess the mechanical performance of biocomposite knotless lateral row anchors based on both anchor design and the direction of pull. Two lateral row greater tuberosity insertion sites (anterior and posterior) were identified in matched pairs of fresh-frozen human cadaveric shoulders DEXA (dual energy X-ray absorptiometry) scanned to verify comparability. The humeri were stripped of all soft tissue and 3 different biocomposite knotless lateral row anchors: HEALIX Knotless BR (DePuy Mitek, Raynham MA), BioComposite PushLock (Arthrex, Naples, FL), and Bio-SwiveLock (Arthrex). Fifty-two anchors were distributed among the insertion locations and tested them with either an anatomic or axial pull. A fixed-gauge loop (15 mm) of 2 high-strength sutures from each anchor was created. After a 10-Nm preload, anchors were cycled from 10 to 45 Nm at 0.5 Hz for 200 cycles and tested to failure at 4.23 mm/second. The load to reach 3 mm and 5 mm displacement, ultimate failure load, displacement at ultimate failure, and failure mode were recorded. Threaded anchors (Bio-SwiveLock, P = .03; HEALIX Knotless, P = .014) showed less displacement with anatomic testing than did the nonthreaded anchor (BioComposite PushLock), and the HEALIX Knotless showed less overall displacement than did the other 2 anchors. The Bio-SwiveLock exhibited greater failure loads than did the other 2 anchors (P < .05). Comparison of axial and anatomic loading showed no maximum load differences for all anchors as a whole (P = .1084). Yet, anatomic pulling produced higher failure loads than did axial pulling for the Bio-SwiveLock but not for the BioComposite PushLock or the HEALIX Knotless. The nonthreaded anchor (BioComposite PushLock) displayed lower failure loads than did both threaded anchors with axial pulling. Threaded biocomposite anchors (HEALIX Knotless BR and Bio-SwiveLock) show less anatomic loading displacement and higher axial failure loads than do the nonthreaded

Pengaruh Latihan Traditional Push Up, Plyometric Push Up, dan Incline Push Up Terhadap Kekuatan Otot Lengan, Power Otot Lengan, dan Daya Tahan Otot Lengan

Directory of Open Access Journals (Sweden)

Febriyan Dwi Cahyono

2018-05-01

Full Text Available Tujuan penelitian ini adalah untuk peningkatan performa fisik otot lengan siswa ekstrakulikuler putra SMAN 2 Lamongan yang memiliki kelemahan saat dilakukan evaluasi fisik. Empat puluh siswa sehat dengan melihat status gizi melalui indeks masa tubuh (IMT dipilih sesuai dengan kriteria dan dilakukan pretest dan pemeringkatan sehingga masuk dalam pengelompokan traditional push up, plyometric push up, incline push up dan kelompok kontrol. Push up 30 detik, push up 60 detik dan medicine ball test digunakan untuk mengukur peningkatan kinerja. Ketiga kelompok berpartisipasi dalam penelitian tiga hari dalam seminggu selama enam minggu dan menyelesaikan 18 sesi pelatihan, pada frekuensi 3 sesi per minggu. Hasil uji paired sample t-test dalam kelompok traditional push up menunjukkan pengaruh yang signifikan pada variabel kekuatan dan daya tahan, kelompok plyometric push up menunjukkan pengaruh yang signifikan pada variabel kekuatan dan power, dan kelompok incline push up menunjukkan pengaruh yang signifikan pada variabel kekuatan dan daya tahan.  Disimpulkan dari penelitian ini bahwa pelatihan traditional push up, plyometric push up dan incline push up ketiganya efektif untuk peningkatan kinerja tubuh bagian atas.

Particle Size (Sieving) and Enthalpy (Acid Calorimetry) Analysis of Single-Pull K East Basin Floor and Pit Sludges

International Nuclear Information System (INIS)

Bredt, P.R.; Delegard, C.H.; Schmidt, A.J.; Silvers, K.L.; Thornton, B.M.; Gano, S.

2000-01-01

This report presents the results of particle size analyses and calorimetry testing performed on selected single-pull sludge samples collected from the Hanford K East Basin between December 1998 and June 1999. The samples were collected as isolated cores predominantly from areas that had not been previously sampled (e.g., North Loadout Pit, Dummy Elevator Pit, Tech View Pit), or from areas in which the sludge composition had been altered since the last sampling (e.g., Weasel Pit). Particle size analyses were performed by washing wet sludge samples through a series of four sieves with openings of 250, 500, 1410, and 4000 microm. The loaded sieves were weighed before and after drying to obtain wet and dry particle size distributions. Knowledge of the particle size distribution is needed to design and predict the performance of the systems that will be used to retrieve, transport, and recover sludge. Also, sieving provides an opportunity to observe the components in the sludge. For example, during sieving of the sludge sample from the North Loadout Pit, significant quantities of organic ion exchange beads were observed. The uranium metal content and the particle size of the uranium metal in the K Basin sludge will largely determine the chemical reactivity of the sludge. In turn, the designs for the sludge handling and storage systems must be compatible with the reactivity of the sludge. Therefore, acid calorimetry was performed to estimate the uranium metal content of the sludge. For this testing, sludge samples were dissolved in nitric acid within a calibrated adiabatic calorimeter. The resulting dissolution enthalpy data were then used to discriminate between metallic uranium (minus3750 J/g in nitric acid) and uranium oxide (minus394 J/g in nitric acid). Results from this testing showed that the single-pull sludge samples contained little or no uranium metal

Non-slipping domains of a pulled spool

International Nuclear Information System (INIS)

Wagner, Clemens; Vaterlaus, Andreas

2014-01-01

We have investigated the pulled spool by considering pulling angles up to 360 ∘ . Our focus was on downward pulling forces with pulling angles in the range of 180 ∘ to 360 ∘ . In this range we have found a domain of pulling angles where the spool never starts to slip independent of the strength of the pulling force. The size of the domain depends on the static friction coefficient and on the moment of inertia of the spool. The non-slipping domain is mainly formed around the critical angle where the static friction force becomes zero. For low static friction the non-slipping domain decays into two different domains. We have determined the limiting angles of the non-slipping domains and explored the transitions from a single domain to two separated domains in parameter space. (paper)

Comparative Analysis of Effect of Density, Insertion Angle and Reinsertion on Pull-Out Strength of Single and Two Pedicle Screw Constructs Using Synthetic Bone Model

OpenAIRE

Krishnan, Venkatesh; Varghese, Vicky; Kumar, Gurunathan Saravana

2016-01-01

Study Design Biomechanical study. Purpose To determine the effect of density, insertion angle and reinsertion on pull-out strength of pedicle screw in single and two screw-rod configurations. Overview of Literature Pedicle screw pull-out studies have involved single screw construct, whereas two screws and rod constructs are always used in spine fusions. Extrapolation of results using the single screw construct may lead to using expensive implants or increasing the fusion levels specifically i...

A study on metallic creep-fatigue interaction at elevated temperatures

International Nuclear Information System (INIS)

Ohnami, Masateru; Sakane, Masao

1978-01-01

In order to investigate the difference between the hold-time effect in push-pull low-cycle fatigue and that in torsional one, both types of strain controlled fatigue tests of SUS 316 stainless steel were performed at 600 0 C with or without hold-time. Significant difference between the push-pull and torsional fatigue test data on the basis of equivalent total strain range of Mises' type was not observed in terms of number of cycles to failure, number of cycles to crack initiation and crack propagation rate. More precisely speaking, however, the push-pull test had a larger hold-time effect on the failure life and on the crack behaviors than the torsional test in lower strain range. That is, slower crack propagation rate was observed in the push-pull test without hold-time than in torsional one, but crack propagation was observed in the push-pull test with hold-time. This crack behavior was discussed from the influence of stress triaxiality near the crack tip on the crack propagation rate and also from the effect of hydrostatic stress. (author)

International migration of health professionals and the marketization and privatization of health education in India: from push-pull to global political economy.

Science.gov (United States)

Walton-Roberts, Margaret

2015-01-01

Health worker migration theories have tended to focus on labour market conditions as principal push or pull factors. The role of education systems in producing internationally oriented health workers has been less explored. In place of the traditional conceptual approaches to understanding health worker, especially nurse, migration, I advocate global political economy (GPE) as a perspective that can highlight how educational investment and global migration tendencies are increasing interlinked. The Indian case illustrates the globally oriented nature of health care training, and informs a broader understanding of both the process of health worker migration, and how it reflects wider marketization tendencies evident in India's education and health systems. The Indian case also demonstrates how the global orientation of education systems in source regions is increasingly central to comprehending the place of health workers in the global and Asian rise in migration. The paper concludes that Indian corporate health care training systems are increasingly aligned with the production of professionals orientated to globally integrated health human resource labour markets, and our conceptual analysis of such processes must effectively reflect these tendencies. Copyright © 2014 Elsevier Ltd. All rights reserved.

Establishment of a new pull-out strength testing method to quantify early osseointegration-An experimental pilot study.

Science.gov (United States)

Nonhoff, J; Moest, T; Schmitt, Christian Martin; Weisel, T; Bauer, S; Schlegel, K A

2015-12-01

The animal study aims to evaluate a new experimental model for measuring sole the influence of the surface characteristics independent from implant macro-design on the level of osseointegration by registering the pull-out strength needed for removal of experimental devices with different surfaces from artificial defects. Seventy-two test bodies (36 with the FRIADENT(®) plus surface, 36 with the P15/HAp biofunctionalized surface) were inserted in six adult domestic pigs with artificial calvarial defects. The experimental devices were designed to fit in the defects leaving a gap between the test body and the local bone. After 21 days of healing, the animals were sacrificed and the test bodies were pulled out with a standardised reproducible pull-out device measuring the pull-out strength. The pull-out strength for both groups was compared. Twenty-one days after insertion a mean force of 412 ± 142 N for the P15/HAp group and 183 ± 105 N for the FRIADENT(®) plus group was measured for the removal of the specimens from the calvarial bone. The difference between the groups was statistically significant (p implant surfaces on the early stage of osseointegration. Copyright © 2015 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

Design of an expert system for the development and formulation of push-pull osmotic pump tablets containing poorly water-soluble drugs.

Science.gov (United States)

Zhang, Zhi-hong; Dong, Hong-ye; Peng, Bo; Liu, Hong-fei; Li, Chun-lei; Liang, Min; Pan, Wei-san

2011-05-30

The purpose of this article was to build an expert system for the development and formulation of push-pull osmotic pump tablets (PPOP). Hundreds of PPOP formulations were studied according to different poorly water-soluble drugs and pharmaceutical acceptable excipients. The knowledge base including database and rule base was built based on the reported results of hundreds of PPOP formulations containing different poorly water-soluble drugs and pharmaceutical excipients and the experiences available from other researchers. The prediction model of release behavior was built using back propagation (BP) neural network, which is good at nonlinear mapping and learning function. Formulation design model was established based on the prediction model of release behavior, which was the nucleus of the inference engine. Finally, the expert system program was constructed by VB.NET associating with SQL Server. Expert system is one of the most popular aspects in artificial intelligence. To date there is no expert system available for the formulation of controlled release dosage forms yet. Moreover, osmotic pump technology (OPT) is gradually getting consummate all over the world. It is meaningful to apply expert system on OPT. Famotidine, a water insoluble drug was chosen as the model drug to validate the applicability of the developed expert system. Copyright © 2011 Elsevier B.V. All rights reserved.

Initial SVE Well Testing for the A-Area Miscellaneous Rubble Pile (ARP) Trenches Area

International Nuclear Information System (INIS)

RIHA, BRIAN

2004-01-01

The A-Area Miscellaneous Rubble Pile (ARP) is a 5.9 acre unit located at the southern end of A/M Area at the Savannah River Site (SRS). Disposal activities at ARP began in the early 1950s. The exact dates of operation and material disposed in the unit remain unknown. Within the ARP exists a smaller, approximately 2 acre, sub unit identified as the Trenches Area. The Trenches Area is dominated by a T-shaped trench (approximately 50 feet wide) containing 8 to 12 feet of ash material. This T-shaped trench will be referred to as the ARP Trench. Vegetation has been removed from the Trenches Area and a lower permeability earthen cover now covers the ARP Trench. The ARP active soil vapor extraction (ASVE) remediation system consists of seven extraction wells and twelve monitoring wells that were pushed into the vadose zone of the ARP Trench. The remediation system was designed based on the pre-design study conducted in 2002. The purpose of the initial soil vapor extraction (SVE) well testing was to verify the integrity and functionality of the nineteen wells installed in the ARP Trench. The well integrity was evaluated based on the flow rate, vacuum, and indication that soil gas and not surface air was pulled from the well. Soil gas was defined as gas with levels of carbon dioxide (CO2) above ambient concentrations (400-700 ppmv). Volatile organic compound (VOC) concentrations were measured at each well to determine the initial distribution of the contamination. In addition, the subsurface vacuum distribution was measured around each extraction well as a relative measure of the influence of each well

Pull-off characteristics of double-shanked compared to single-shanked ligation clips: an animal study

Directory of Open Access Journals (Sweden)

Schenk Martin

2016-09-01

Full Text Available The use of surgical ligation clips is considered as the gold standard for the closure of vessels, particularly in laparoscopic surgery. The safety of clips is mainly achieved by the deep indentation of the metal bar with a high retention force. A novel double-shanked (DS titanium clip was compared to two single-shanked clips with respect to axial and radial pull-off forces.

In-situ uranium mining: reservoir engineering aspects of leaching and restoration

International Nuclear Information System (INIS)

Kabir, M.I.

1982-01-01

To establish the feasibility of in-situ mining of uranium, a push-pull test of an in-situ uranium leaching process, which consists of a single injection/production test well and two observation wells, was designed to evaluate the parameters which govern the uranium production and restorability of a solution mined zone. The test procedure itself consists of injection (push cycle) of a preflush followed by lixiviant, a brief soak period (soak cycle), and subsequent production (pull cycle) into the same well. Based on computer modeling, procedures are defined which permit, for a properly designed test, the determination of both restoration and leaching parameters. The test procedure and design recommendations are also outlined. Two numerical simulators which model field scale uranium production and restoration operations are presented. These simulators are able to accommodate various well patterns and irregular reservoir boundaries, physical dispersion, directional permeability variations (if present), and a variety of injection/production strategies. A streamline-concentration balance technique has been used to develop the models. The assumption of time invariant boundary conditions and no transverse dispersion between the streamlines reduces the two dimensional problem to a bundle of one dimensional ones. It has been further shown that the production well effluent histories can easily be obtained by superposing the solution of the concentration balance equations for a single streamline, and thus reducing computation time significantly. Finally, the simulators have been used to study various reservoir engineering aspects to optimize in-situ uranium production from field scale operations

In-situ uranium mining: reservoir engineering aspects of leaching and restoration

Energy Technology Data Exchange (ETDEWEB)

Kabir, M.I.

1982-01-01

To establish the feasibility of in-situ mining of uranium, a push-pull test of an in-situ uranium leaching process, which consists of a single injection/production test well and two observation wells, was designed to evaluate the parameters which govern the uranium production and restorability of a solution mined zone. The test procedure itself consists of injection (push cycle) of a preflush followed by lixiviant, a brief soak period (soak cycle), and subsequent production (pull cycle) into the same well. Based on computer modeling, procedures are defined which permit, for a properly designed test, the determination of both restoration and leaching parameters. The test procedure and design recommendations are also outlined. Two numerical simulators which model field scale uranium production and restoration operations are presented. These simulators are able to accommodate various well patterns and irregular reservoir boundaries, physical dispersion, directional permeability variations (if present), and a variety of injection/production strategies. A streamline-concentration balance technique has been used to develop the models. The assumption of time invariant boundary conditions and no transverse dispersion between the streamlines reduces the two dimensional problem to a bundle of one dimensional ones. It has been further shown that the production well effluent histories can easily be obtained by superposing the solution of the concentration balance equations for a single streamline, and thus reducing computation time significantly. Finally, the simulators have been used to study various reservoir engineering aspects to optimize in-situ uranium production from field scale operations.

A new apparatus and method for mixing solutes for injection tests

African Journals Online (AJOL)

2009-07-17

Jul 17, 2009 ... ISSN 1816-7950 (On-line) = Water SA Vol. 37 No. 2 April 2011 ... the push-pull test, a tracer is introduced to the standing water .... the assembly leak-proof. ..... ment of Rural Water Supply Management Strategies for Secondary.

The string-pulling paradigm in comparative psychology.

Science.gov (United States)

Jacobs, Ivo F; Osvath, Mathias

2015-05-01

String pulling is one of the most widely used paradigms in comparative psychology. First documented 2 millennia ago, it has been a well-established scientific paradigm for a century. More than 160 bird and mammal species have been tested in over 200 studies with countless methodological variations. The paradigm can be used to address a wide variety of issues on animal cognition; for example, what animals understand about contact and connection as well as whether they rely on perceptual feedback, grasp the functionality of strings, generalize across conditions, apply their knowledge flexibly, and possess insight. Mammals are typically tested on a horizontal configuration, birds on a vertical one, making the studies difficult to compare; in particular, pulling a string vertically requires better coordination and attention. A species' performance on the paradigm is often influenced by its ecology, especially concerning whether limbs are used for foraging. Many other factors can be of importance and should be considered. The string-pulling paradigm is easy to administer, vary, and apply to investigate a wide array of cognitive abilities. Although it can be and has been used to compare species, divergent methods and unclear reporting have limited its comparative utility. With increasing research standards, the paradigm is expected to become an even more fundamental tool in comparative psychology. (c) 2015 APA, all rights reserved).

Delayed pull-in transitions in overdamped MEMS devices

Science.gov (United States)

Gomez, Michael; Moulton, Derek E.; Vella, Dominic

2018-01-01

We consider the dynamics of overdamped MEMS devices undergoing the pull-in instability. Numerous previous experiments and numerical simulations have shown a significant increase in the pull-in time under DC voltages close to the pull-in voltage. Here the transient dynamics slow down as the device passes through a meta-stable or bottleneck phase, but this slowing down is not well understood quantitatively. Using a lumped parallel-plate model, we perform a detailed analysis of the pull-in dynamics in this regime. We show that the bottleneck phenomenon is a type of critical slowing down arising from the pull-in transition. This allows us to show that the pull-in time obeys an inverse square-root scaling law as the transition is approached; moreover we determine an analytical expression for this pull-in time. We then compare our prediction to a wide range of pull-in time data reported in the literature, showing that the observed slowing down is well captured by our scaling law, which appears to be generic for overdamped pull-in under DC loads. This realization provides a useful design rule with which to tune dynamic response in applications, including state-of-the-art accelerometers and pressure sensors that use pull-in time as a sensing mechanism. We also propose a method to estimate the pull-in voltage based only on data of the pull-in times.

Push-off tests and strength evaluation of joints combining shrink fitting with bonding

Science.gov (United States)

Yoneno, Masahiro; Sawa, Toshiyuki; Shimotakahara, Ken; Motegi, Yoichi

1997-03-01

Shrink fitted joints have been used in mechanical structures. Recently, joints combining shrink fitting with anaerobic adhesives bonded between the shrink fitted surfaces have been appeared in order to increase the joint strength. In this paper, push-off test was carried out on strength of joints combining shrink fitting with bonding by material testing machine. In addition, the push-off strength of shrink fitting joints without an anaerobic adhesive was also measured. In the experiments, the effects of the shrinking allowance and the outer diameter of the rings on the joint strength are examined. The interface stress distribution in bonded shrink fitted joints subjected to a push-off load is analyzed using axisymmetrical theory of elasticity as a four-body contact problem. Using the interface stress distribution, a method for estimating joint strength is proposed. The experimental results are in a fairly good agreement with the numerical results. It is found that the strength of combination joints is greater than that of shrink fitted joints.

Influence of different adhesive systems on the pull-out bond strength of glass fiber posts.

Science.gov (United States)

da Silva, Luciana Mendonça; Andrade, Andréa Mello de; Machuca, Melissa Fernanda Garcia; da Silva, Paulo Maurício Batista; da Silva, Ricardo Virgolino C; Veronezi, Maria Cecília

2008-01-01

This in vitro study evaluated the tensile bond strength of glass fiber posts (Reforpost - Angelus-Brazil) cemented to root dentin with a resin cement (RelyX ARC - 3M/ESPE) associated with two different adhesive systems (Adper Single Bond - 3M/ESPE and Adper Scotchbond Multi Purpose (MP) Plus - 3M/ESPE), using the pull-out test. Twenty single-rooted human teeth with standardized root canals were randomly assigned to 2 groups (n=10): G1- etching with 37% phosphoric acid gel (3M/ESPE) + Adper Single Bond + #1 post (Reforpost - Angelus) + four #1 accessory posts (Reforpin - Angelus) + resin cement; G2- etching with 37% phosphoric acid gel + Adper Scotchbond MP Plus + #1 post + four #1 accessory posts + resin cement. The specimens were stored in distilled water at 37 degrees C for 7 days and submitted to the pull-out test in a universal testing machine (EMIC) at a crosshead speed of 0.5 mm/min. The mean values of bond strength (kgf) and standard deviation were: G1- 29.163 +/- 7.123; G2- 37.752 +/-13.054. Statistical analysis (Student's t-test; a=0.05 showed no statistically significant difference (pAdhesive bonding failures between resin cement and root canal dentin surface were observed in both groups, with non-polymerized resin cement in the apical portion of the post space when Single Bond was used (G1). The type of adhesive system employed on the fiber post cementation did not influence the pull-out bond strength.

Influence of different adhesive systems on the pull-out bond strength of glass fiber posts

Directory of Open Access Journals (Sweden)

Luciana Mendonça da Silva

2008-06-01

Full Text Available This in vitro study evaluated the tensile bond strength of glass fiber posts (Reforpost - Angelus-Brazil cemented to root dentin with a resin cement (RelyX ARC - 3M/ESPE associated with two different adhesive systems (Adper Single Bond - 3M/ESPE and Adper Scotchbond Multi Purpose (MP Plus - 3M/ESPE, using the pull-out test. Twenty single-rooted human teeth with standardized root canals were randomly assigned to 2 groups (n=10: G1- etching with 37% phosphoric acid gel (3M/ESPE + Adper Single Bond + #1 post (Reforpost - Angelus + four #1 accessory posts (Reforpin - Angelus + resin cement; G2- etching with 37% phosphoric acid gel + Adper Scotchbond MP Plus + #1 post + four #1 accessory posts + resin cement. The specimens were stored in distilled water at 37°C for 7 days and submitted to the pull-out test in a universal testing machine (EMIC at a crosshead speed of 0.5 mm/min. The mean values of bond strength (kgf and standard deviation were: G1- 29.163 ± 7.123; G2- 37.752 ±13.054. Statistical analysis (Student's t-test; a=0.05 showed no statistically significant difference (p<0.05 between the groups. Adhesive bonding failures between resin cement and root canal dentin surface were observed in both groups, with non-polymerized resin cement in the apical portion of the post space when Single Bond was used (G1. The type of adhesive system employed on the fiber post cementation did not influence the pull-out bond strength.

Effect of intercalation and chromophore arrangement on the linear and nonlinear optical properties of model aminopyridine push–pull molecules

Czech Academy of Sciences Publication Activity Database

Bureš, F.; Cvejn, D.; Melánová, Klára; Beneš, L.; Svoboda, Jan; Zima, Vítězslav; Pytela, O.; Mikysek, T.; Růžičková, Z.; Kityk, I. V.; Wojciechowski, A.; AlZayed, N.

2016-01-01

Roč. 4, č. 3 (2016), s. 468-478 ISSN 2050-7526 R&D Projects: GA ČR(CZ) GA13-01061S Institutional support: RVO:61389013 Keywords : push-pull chromophore * intercalation * layered phosphates Subject RIV: CA - Inorganic Chemistry Impact factor: 5.256, year: 2016

Test results of the AGS Booster low frequency RF system

International Nuclear Information System (INIS)

Sanders, R.T.; Cameron, P.; Damm, R.; Dunbar, A.; Goldman, M.; Kasha, D.; McNerney, A.; Meth, M.; Ratti, A.; Spitz, R.

1993-01-01

The Band II RF system was originally built to support the Booster operations during the acceleration of heavy ions. Designed to sweep from 0.6 to 2.5 MHz, it was build and successfully tested over a much broader range reaching 4 MHz. Voltages up to more than 20 kV were reached over the design frequency range. The system consists of two stations, each of which is made of one single gap cavity directly driven by a grounded cathode push pull power amplifier. The low Q high permeability ferrites needed in the coaxial cavity in order to reach the lower end of the band make tuning extremely easy. Both systems were thoroughly tested both at single frequencies and on a sweep and are now installed in the ring, ready for operations. Static measurements showed no high-loss effects. The Band 11 system has been fully described in a previous paper; presented here are the results of the ''bench'' tests that lead to important performance improvements

Static Pull Testing of a New Type of Large Deformation Cable with Constant Resistance

Directory of Open Access Journals (Sweden)

Zhigang Tao

2017-01-01

Full Text Available A new type of energy-absorbing cable, Constant-Resistance Large Deformation cable (CRLD cable with three different specifications, has been recently developed and tested. An effective cable should occupy the ability of absorbing deformation energy from these geodisaster loads and additionally must be able to yield with the sliding mass movements and plastic deformation over large distances at high displacement rates. The new cable mainly consists of constant-resistance casing tube and frictional cone unit that transfers the load from the slope. When experiencing a static or dynamic load and especially the load exceeding the constant resistance force (CR-F, a static friction force derived from the movement of frictional cone unit in casing tube of CRLD cable, the frictional cone unit will move in the casing tube along the axis and absorb deformation energy, accordingly. In order to assess the performance of three different specified cables in situ, a series of field static pull tests have been performed. The results showed that the first type of CRLD cable can yield 2000 mm displacement while acting 850 kN static pull load, which is superior to that of other two types, analyzing based on the length of the displacement and the level of static pull load.

Analysis of CFRP Joints by Means of T-Pull Mechanical Test and Ultrasonic Defects Detection

Directory of Open Access Journals (Sweden)

Caterina Casavola

2018-04-01

Full Text Available Defects detection within a composite component, with the aim of understanding and predicting its mechanical behavior, is of great importance in the aeronautical field because the irregularities of the composite material could compromise functionality. The aim of this paper is to detect defects by means of non-destructive testing (NDT on T-pull samples made by carbon fiber reinforced polymers (CFRP and to evaluate their effect on the mechanical response of the material. Samples, obtained from an industrial stringer having an inclined web and realized with a polymeric filler between cap and web, were subjected to ultrasonic monitoring and then to T-pull mechanical tests. All samples were tested with the same load mode and the same test configuration. An experimental set-up consisting of a semiautomatic C-scan ultrasonic mapping system with a phased array probe was designed and developed, optimizing control parameters and implementing image processing software. The present work is carried out on real composites parts that are characterized by having their intrinsic defectiveness, as opposed to the previous similar results in the literature mainly obtained on composite parts with artificially produced defects. In fact, although samples under study were realized free from defects, ultrasonic mapping found defectiveness inside the material. Moreover, the ultrasonic inspection could be useful in detecting both the location and size of defects. Experimental data were critically analyzed and qualitatively correlated with results of T-pull mechanical tests in order to better understand and explain mechanical behavior in terms of fracture mode.

Analysis of CFRP Joints by Means of T-Pull Mechanical Test and Ultrasonic Defects Detection.

Science.gov (United States)

Casavola, Caterina; Palano, Fania; De Cillis, Francesco; Tati, Angelo; Terzi, Roberto; Luprano, Vincenza

2018-04-18

Defects detection within a composite component, with the aim of understanding and predicting its mechanical behavior, is of great importance in the aeronautical field because the irregularities of the composite material could compromise functionality. The aim of this paper is to detect defects by means of non-destructive testing (NDT) on T-pull samples made by carbon fiber reinforced polymers (CFRP) and to evaluate their effect on the mechanical response of the material. Samples, obtained from an industrial stringer having an inclined web and realized with a polymeric filler between cap and web, were subjected to ultrasonic monitoring and then to T-pull mechanical tests. All samples were tested with the same load mode and the same test configuration. An experimental set-up consisting of a semiautomatic C-scan ultrasonic mapping system with a phased array probe was designed and developed, optimizing control parameters and implementing image processing software. The present work is carried out on real composites parts that are characterized by having their intrinsic defectiveness, as opposed to the previous similar results in the literature mainly obtained on composite parts with artificially produced defects. In fact, although samples under study were realized free from defects, ultrasonic mapping found defectiveness inside the material. Moreover, the ultrasonic inspection could be useful in detecting both the location and size of defects. Experimental data were critically analyzed and qualitatively correlated with results of T-pull mechanical tests in order to better understand and explain mechanical behavior in terms of fracture mode.

Problem solving capabilities of Peach-fronted Conures (Eupsittula aurea) studied by the string-pulling test

DEFF Research Database (Denmark)

Ortiz, Sara Torres; Larsen, Ole Næsbye; Wahlberg, Magnus

Many studies have indicated advanced cognitive abilities in different species of parrots and ravens. Here we investigated basic cognitive skills of Peach-fronted Conures (Eupsittula aurea) using the string-pulling test. These small Middle-American parrots are often compared to dolphins due...... not be obtained by flying or reached from the ground. By varying different spatial configurations of strings and rewards, different cognitive skills could be investigated. Four conures (two females and two males) were tested. All four individuals solved three out of four tested string configurations (four...... straight strings, two slant strings, two contact-no contact strings) within 14 seconds on average, but all failed in a crossed two-string test. Subsequently we tested the birds with a vertical pulley that required the birds to pull the string down to get the food reward within reach from below...

Cyclic Fiber Push-In Test Monitors Evolution of Interfacial Behavior in Ceramic Matrix Composites

Science.gov (United States)

Eldridge, Jeffrey I.

1998-01-01

SiC fiber-reinforced ceramic matrix composites are being developed for high-temperature advanced jet engine applications. Obtaining a strong, tough composite material depends critically on optimizing the mechanical coupling between the reinforcing fibers and the surrounding matrix material. This has usually been accomplished by applying a thin C or BN coating onto the surface of the reinforcing fibers. The performance of these fiber coatings, however, may degrade under cyclic loading conditions or exposure to different environments. Degradation of the coating-controlled interfacial behavior will strongly affect the useful service lifetime of the composite material. Cyclic fiber push-in testing was applied to monitor the evolution of fiber sliding behavior in both C- and BN-coated small-diameter (15-mm) SiC-fiber-reinforced ceramic matrix composites. The cyclic fiber push-in tests were performed using a desktop fiber push-out apparatus. At the beginning of each test, the fiber to be tested was aligned underneath a 10- mm-diameter diamond punch; then, the applied load was cycled between selected maximum and minimum loads. From the measured response, the fiber sliding distance and frictional sliding stresses were determined for each cycle. Tests were performed in both room air and nitrogen. Cyclic fiber push-in tests of C-coated, SiC-fiber-reinforced SiC showed progressive increases in fiber sliding distances along with decreases in frictional sliding stresses for continued cycling in room air. This rapid degradation in interfacial response was not observed for cycling in nitrogen, indicating that moisture exposure had a large effect in immediately lowering the frictional sliding stresses of C-coated fibers. These results indicate that matrix cracks bridged by C-coated fibers will not be stable, but will rapidly grow in moisture-containing environments. In contrast, cyclic fiber push-in tests of both BN-coated, SiC-fiber-reinforced SiC and BNcoated, Si

Diode-pumped laser with Yb:YAG single-crystal fiber grown by the micro-pulling down technique

Science.gov (United States)

Sangla, D.; Aubry, N.; Didierjean, J.; Perrodin, D.; Balembois, F.; Lebbou, K.; Brenier, A.; Georges, P.; Tillement, O.; Fourmigué, J.-M.

2009-02-01

Laser emission obtained from an Yb:YAG single-crystal fiber directly grown by the micro-pulling down technique is demonstrated for the first time. We achieved 11.2 W of continuous wave (CW) output power at 1031 nm for 55 W of incident pump power at 940 nm. In the Q-switched regime, we obtained pulses as short as 17 ns, for an average power of 2.3 W at 2 kHz corresponding to an energy of 1.15 mJ. In both cases, the M 2 factor was 2.5. This single-crystal fiber showed performance similar to a standard rod elaborated by the Czochralski method. The potential of Yb3+-doped single-crystal fibers is presented for scalable high-average and high-peak-power laser systems.

Development of Radon-222 as Natural Tracer for Monitoring the Remediation of NAPL in the Subsurface

International Nuclear Information System (INIS)

Davis, Brian M.; Semprini, Lewis; Istok, Jonathan

2003-01-01

Naturally occurring 222-radon in ground water can potentially be used as an in situ partitioning tracer to characterize dense nonaqueous phase liquid (DNAPL) saturations. The static method involves comparing radon concentrations in water samples from DNAPL-contaminated and non-contaminated portions of an aquifer. During a push-pull test, a known volume of test solution (radon-free water containing a conservation tracer) is first injected (''pushed'') into a well; flow is then reversed and the test solution/groundwater mixture is extracted (''pulled'') from the same well. In the presence of NAPL radon transport is retarded relative to the conservative tracer. Assuming linear equilibrium partitioning, retardation factors for radon can be used to estimate NAPL saturations.The utility of this methodology was evaluated in laboratory and field settings

Pulling cylindrical particles using a soft-nonparaxial tractor beam

DEFF Research Database (Denmark)

Novitsky, Andrey; Ding, Weiqiang; Wang, Maoyan

2017-01-01

In order to pull objects towards the light source a single tractor beam inevitably needs to be strongly nonparaxial. This stringent requirement makes such a tractor beam somewhat hypothetical. Here we reveal that the cylindrical shape of dielectric particles can effectively mitigate the nonparaxi......In order to pull objects towards the light source a single tractor beam inevitably needs to be strongly nonparaxial. This stringent requirement makes such a tractor beam somewhat hypothetical. Here we reveal that the cylindrical shape of dielectric particles can effectively mitigate...... the nonparaxiality requirements, reducing the incidence angle of the partial plane waves of the light beam down to 45 degrees and even to 30 degrees for respectively dipole and dipole-quadrupole objects. The optical pulling force attributed to the interaction of magnetic dipole and magnetic quadrupole moments...... and sorting of targeted particles....

Future application of Czochralski crystal pulling for silicon

Science.gov (United States)

Matlcok, J. H.

1985-08-01

Czochralski (Cz) crystal pulling has been the predominant method used for preparing silicon single crystal for the past twenty years. The fundamental technology used has changed little. However, great strides have been made in learning how to make the crystals bigger and of better quality at ever increasing productivity rates. Currently charge sizes of 50 kg of polycrystal silicon are being used for production and crystals up to ten inches in diameter have been grown without major difficulty. The largest material actually being processed in silicon wafer form is 150 mm (6 inches) in diameter. Growing of crystals in a magnetic field has proved to be particularly useful for microscopic impurity control. Major developments in past years on equipment for Cz crystal pulling have included the automatic growth control of the diameter as well as the starting core of the crystal, the use of magnetic fields and around the crystal puller to supress convection, various recharging schemes for dopant control and the use of continuous liquid feed in the crystal puller. The latter, while far from being a reliable production process, is ideal in concept for major improvement in Cz crystal pulling. The Czochralski process will maintain its dominance of silicon crystal production for many years.

Optical and Photovoltaic Properties of Thieno[3,2-b]thiophene-Based Push-Pull Organic Dyes with Different Anchoring Groups for Dye-Sensitized Solar Cells.

Science.gov (United States)

Fernandes, Sara S M; Castro, M Cidália R; Pereira, Ana Isabel; Mendes, Adélio; Serpa, Carlos; Pina, João; Justino, Licínia L G; Burrows, Hugh D; Raposo, M Manuela M

2017-12-31

The effect of anchoring groups on the optical and electrochemical properties of triphenylamine-thienothiophenes, and on the photovoltaic performance of DSSCs photosensitized with the prepared dyes, was studied using newly synthesized compounds with cyanoacetic acid or rhodanine-3-acetic acid groups. Precursor aldehydes were synthesized through Suzuki cross-coupling, whereas Knoevenagel condensation of these with 2-cyanoacetic acid or rhodanine-3-acetic acid afforded the final push-pull dyes. A comprehensive photophysical study was performed in solution and in the solid state. The femtosecond time-resolved transient absorption spectra for the synthesized dyes were obtained following photoexcitation in solution and for the dyes adsorbed to TiO 2 mesoporous films. Information on conformation, electronic structure, and electron distribution was obtained by density functional theory (DFT) and time-dependent DFT calculations. Triphenylamine-thienothiophene functionalized with a cyanoacetic acid anchoring group displayed the highest conversion efficiency (3.68%) as the dye sensitizer in nanocrystalline TiO 2 solar cells. Coadsorption studies were performed for this dye with the ruthenium-based N719 dye, and they showed dye power conversion efficiencies enhanced by 20-64%. The best cell performance obtained with the coadsorbed N719 and cyanoacetic dye showed an efficiency of 6.05%.

Mechanism of oil-pulling therapy - in vitro study.

Science.gov (United States)

Asokan, Sharath; Rathinasamy, T K; Inbamani, N; Menon, Thangam; Kumar, S Senthil; Emmadi, Pamela; Raghuraman, R

2011-01-01

Oil pulling has been used extensively as a traditional Indian folk remedy without scientific proof for many years for strengthening teeth, gums and jaws and to prevent decay, oral malodor, bleeding gums and dryness of throat and cracked lips. The aim of this study was to evaluate the antibacterial activity of sesame oil and lignans isolated from sesame oil on oral microorganisms and to check whether saponification or emulsification occurs during oil-pulling therapy. The in vitro study was carried out in three different phases: (1) Antibacterial activity of the lignans and sesame oil were tested by minimum inhibitory concentration assay by agar dilution method and agar well diffusion method, respectively. (2) Increase in free fatty acid level of oil and the quantity of sodium hydroxide (NaOH) used up in the titration are good indicators of saponification process. This was assessed using analytical tests for vegetable oils. (3) Swished oil was observed under light microscope to assess the status of the oil, presence of microorganisms, oral debris and foreign bodies. Sesamin and sesamolin isolated from sesame oil did not have any antibacterial effect against oral microorganisms like Streptococcus mutans, Streptococcus mitis and Streptococcus viridans. Emulsification of sesame oil occurs during oil-pulling therapy. Increased consumption of NaOH in titration is a definite indication of a possible saponification process. The myth that the effect of oil-pulling therapy on oral health was just a placebo effect has been broken and there are clear indications of possible saponification and emulsification process, which enhances its mechanical cleaning action.

Push-pull-thinking

DEFF Research Database (Denmark)

Kolodovski, A.

2006-01-01

Scientific innovation takes two distinct paths. Sometimes, companies ask researchers to develop a solution for a specific business problem. This is a demand-driven, “PULL” method. In other cases, scientists develop a technology with new valuablecapabilities, and then search for commercial applica...

Kinematics and kinetics of the bench-press and bench-pull exercises in a strength-trained sporting population.

Science.gov (United States)

Pearson, Simon N; Cronin, John B; Hume, Patria A; Slyfield, David

2009-09-01

Understanding how loading affects power production in resistance training is a key step in identifying the most optimal way of training muscular power - an essential trait in most sporting movements. Twelve elite male sailors with extensive strength-training experience participated in a comparison of kinematics and kinetics from the upper body musculature, with upper body push (bench press) and pull (bench pull) movements performed across loads of 10-100% of one repetition maximum (1RM). 1RM strength and force were shown to be greater in the bench press, while velocity and power outputs were greater for the bench pull across the range of loads. While power output was at a similar level for the two movements at a low load (10% 1RM), significantly greater power outputs were observed for the bench pull in comparison to the bench press with increased load. Power output (Pmax) was maximized at higher relative loads for both mean and peak power in the bench pull (78.6 +/- 5.7% and 70.4 +/- 5.4% of 1RM) compared to the bench press (53.3 +/- 1.7% and 49.7 +/- 4.4% of 1RM). Findings can most likely be attributed to differences in muscle architecture, which may have training implications for these muscles.

Investigation on Bond-Slip Behavior of Z-Pin Interfaces in X-Cor® Sandwich Structures Using Z-Pin Pull-Out Test

Science.gov (United States)

Shan, Hangying; Xiao, Jun; Chu, Qiyi

2018-05-01

The Z-Pin interfacial bond properties play an important role in the structural performance of X-Cor® sandwich structures. This paper presents an experimental investigation on bond-slip behavior of Z-Pin interfaces using Z-Pin pull-out test. Based on the experimental data the whole Z-Pin pull-out process consists of three stages: initial bonding, debonding and frictional sliding. Comparative experimental study on the influence of design parameters on bond-slip behavior of Z-Pin interfaces has also been performed. Numerical analyses were conducted with the ABAQUS finite element (FE) program to simulate the Z-Pins bond-slip response of the pull-out test. The Z-Pins interfacial bond-slip behavior was implemented using nonlinear spring elements characterized with the constitutive relation from experimental results. Numerical results were validated by comparison with experimental data, and reasonably good agreement was achieved between experimental and analytical pull-out force-slip curves.

Experimental Investigations on the Pull-Out Behavior of Tire Strips Reinforced Sands.

Science.gov (United States)

Li, Li-Hua; Chen, Yan-Jun; Ferreira, Pedro Miguel Vaz; Liu, Yong; Xiao, Heng-Lin

2017-06-27

Waste tires have excellent mechanical performance and have been used as reinforcing material in geotechnical engineering; however, their interface properties are poorly understood. To further our knowledge, this paper examines the pull-out characteristics of waste tire strips in a compacted sand, together with uniaxial and biaxial geogrids also tested under the same conditions. The analysis of the results shows that the interlocking effect and pull-out resistance between the tire strip and the sand is very strong and significantly higher than that of the geogrids. In the early stages of the pull-out test, the resistance is mainly provided by the front portion of the embedded tire strips, as the pull-out test continues, more and more of the areas towards the end of the tire strips are mobilized, showing a progressive failure mechanism. The deformations are proportional to the frictional resistance between the tire-sand interface, and increase as the normal stresses increase. Tire strips of different wear intensities were tested and presented different pull-out resistances; however, the pull-out resistance mobilization patterns were generally similar. The pull-out resistance values obtained show that rubber reinforcement can provide much higher pull-out forces than the geogrid reinforcements tested here, showing that waste tires are an excellent alternative as a reinforcing system, regardless of the environmental advantages.

Future Food Production System Development Pulling From Space Biology Crop Growth Testing in Veggie

Science.gov (United States)

Massa, Gioia; Romeyn, Matt; Fritsche, Ralph

2017-01-01

Preliminary crop testing using Veggie indicates the environmental conditions provided by the ISS are generally suitable for food crop production. When plant samples were returned to Earth for analysis, their levels of nutrients were comparable to Earth-grown ground controls. Veggie-grown produce food safety microbiology analysis indicated that space-grown crops are safe to consume. Produce sanitizing wipes were used on-orbit to further reduce risk of foodborne illness. Validation growth tests indicated abiotic challenges of insufficient or excess fluid delivery, potentially reduced air flow leading to excess water, elevated CO2 leading to physiological responses, and microorganisms that became opportunistic pathogens. As NASA works to develop future space food production, several areas of research to define these systems pull from the Veggie technology validation tests. Research into effective, reusable water delivery and water recovery methods for future food production systems arises from abiotic challenges observed. Additionally, impacts of elevated CO2 and refinement of fertilizer and light recipes for crops needs to be assessed. Biotic pulls include methods or technologies to effectively sanitize produce with few consumables and low inputs; work to understand the phytomicrobiome and potentially use it to protect crops or enhance growth; selection of crops with high harvest index and desirable flavors for supplemental nutrition; crops that provide psychosocial benefits, and custom space crop development. Planning for future food production in a deep space gateway or a deep space transit vehicle requires methods of handling and storing seeds, and ensuring space seeds are free of contaminants and long-lived. Space food production systems may require mechanization and autonomous operation, with preliminary testing initiated to identify operations and capabilities that are candidates for automation. Food production design is also pulling from Veggie logistics

Single-well injection-withdrawal tests (SWIW). Investigation of evaluation aspects under heterogeneous crystalline bedrock conditions

International Nuclear Information System (INIS)

Nordqvist, Rune; Gustafsson, Erik

2004-08-01

Single-well injection-withdrawal (SWIW) tracer tests have been identified by SKB as an investigation method for solute transport properties in the forthcoming site investigations. A previous report presents a literature study as well as scoping calculations for SWIW tests in homogeneous crystalline bedrock environments. The present report comprises further scoping calculations under assumptions of heterogeneous bedrock conditions. Simple but plausible homogeneous evaluation models are tested on simulated SWIW tests in hypothetical heterogeneous two-dimensional fractures. The results from this study indicate that heterogeneity may cause effects of flow irreversibility when background hydraulic gradients are significant and the tested section is located in a dominating flow path. This implies that such conditions make it more difficult to interpret results from SWIW tests of longer duration with sorbing and/or diffusing tracers. Sorption and diffusion processes may be best studied when SWIW tests are conducted in borehole sections with low natural flow rates

CAN UPPER EXTREMITY FUNCTIONAL TESTS PREDICT THE SOFTBALL THROW FOR DISTANCE: A PREDICTIVE VALIDITY INVESTIGATION

Science.gov (United States)

Hanney, William J.; Kolber, Morey J.; Davies, George J.; Riemann, Bryan

2011-01-01

Introduction: Understanding the relationships between performance tests and sport activity is important to the rehabilitation specialist. The purpose of this study was two- fold: 1) To identify if relationships exist between tests of upper body strength and power (Single Arm Seated Shot Put, Timed Push-Up, Timed Modified Pull-Up, and The Davies Closed Kinetic Chain Upper Extremity Stability Test, and the softball throw for distance), 2) To determine which variable or group of variables best predicts the performance of a sport specific task (the softball throw for distance). Methods: One hundred eighty subjects (111 females and 69 males, aged 18-45 years) performed the 5 upper extremity tests. The Pearson product moment correlation and a stepwise regression were used to determine whether relationships existed between performance on the tests and which upper extremity test result best explained the performance on the softball throw for distance. Results: There were significant correlations (r=.33 to r=.70, p=0.001) between performance on all of the tests. The modified pull-up test was the best predictor of the performance on the softball throw for distance (r2= 48.7), explaining 48.7% of variation in performance. When weight, height, and age were added to the regression equation the r2 values increased to 64.5, 66.2, and 67.5 respectively. Conclusion: The results of this study indicate that several upper extremity tests demonstrate significant relationships with one another and with the softball throw for distance. The modified pull up test was the best predictor of performance on the softball throw for distance. PMID:21712942

Using three-dimensional rapid prototyping in the design and development of orthopaedic screws in standardised pull-out tests.

Science.gov (United States)

Leslie, Laura Jane; Connolly, Ashley; Swadener, John G; Junaid, Sarah; Theivendran, Kanthan; Deshmukh, Subodh C

2018-05-01

The majority of orthopaedic screws are designed, tested and manufactured by existing orthopaedics companies and are predominantly developed with healthy bone in mind. The timescales and costs involved in the development of a new screw design, for example, for osteoporotic bone, are high. In this study, standard wood screws were used to analyse the concept of using three-dimensional printing, or rapid prototyping, as a viable stage of development in the design of a new bone screw. Six wood screws were reverse engineered and printed in polymeric material using stereolithography. Three of the designs were also printed in Ti6Al4V using direct metal laser sintering; however, these were not of sufficient quality to test further. Both the original metal screws (metal) and polymeric rapid prototyping screws were then tested using standard pull-out tests from low-density polyurethane blocks (Sawbones). Results showed the highest pull-out strengths for screws with the longest thread length and the smallest inner diameter. Of the six screw designs tested, five showed no more than a 17% variance between the metal and rapid prototyping results. A similar pattern of results was shown between the screw designs for both the metal and rapid prototyping screws in five of the six cases. While not producing fully comparable pull-out results to orthopaedic screws, the results from this study do provide evidence of the potential usefulness and cost-effectiveness of rapid prototyping in the early stages of design and testing of orthopaedic screws.

Well installation, single-well testing, and particle-size analysis for selected sites in and near the Lost Creek Designated Ground Water Basin, north-central Colorado, 2003-2004

Science.gov (United States)

Beck, Jennifer A.; Paschke, Suzanne S.; Arnold, L. Rick

2011-01-01

This report describes results from a groundwater data-collection program completed in 2003-2004 by the U.S. Geological Survey in support of the South Platte Decision Support System and in cooperation with the Colorado Water Conservation Board. Two monitoring wells were installed adjacent to existing water-table monitoring wells. These wells were installed as well pairs with existing wells to characterize the hydraulic properties of the alluvial aquifer and shallow Denver Formation sandstone aquifer in and near the Lost Creek Designated Ground Water Basin. Single-well tests were performed in the 2 newly installed wells and 12 selected existing monitoring wells. Sediment particle size was analyzed for samples collected from the screened interval depths of each of the 14 wells. Hydraulic-conductivity and transmissivity values were calculated after the completion of single-well tests on each of the selected wells. Recovering water-level data from the single-well tests were analyzed using the Bouwer and Rice method because test data most closely resembled those obtained from traditional slug tests. Results from the single-well test analyses for the alluvial aquifer indicate a median hydraulic-conductivity value of 3.8 x 10-5 feet per second and geometric mean hydraulic-conductivity value of 3.4 x 10-5 feet per second. Median and geometric mean transmissivity values in the alluvial aquifer were 8.6 x 10-4 feet squared per second and 4.9 x 10-4 feet squared per second, respectively. Single-well test results for the shallow Denver Formation sandstone aquifer indicate a median hydraulic-conductivity value of 5.4 x 10-6 feet per second and geometric mean value of 4.9 x 10-6 feet per second. Median and geometric mean transmissivity values for the shallow Denver Formation sandstone aquifer were 4.0 x 10-5 feet squared per second and 5.9 x 10-5 feet squared per second, respectively. Hydraulic-conductivity values for the alluvial aquifer in and near the Lost Creek Designated

Versatile H+ beam chopper system at LAMPF

International Nuclear Information System (INIS)

Lunsford, J.S.; Lawrence, G.P.; Bentley, R.F.

1979-01-01

The H + chopper system at LAMPF provides two modes (A and B) of beam chopping. Mode A provides single micropulses separated by 1 μs or more. Mode B provides a single pulse 50-ns to 10-μs long at the LAMPF repetition rate of 12 Hz. The mode of operation is selected with coaxial relays which can switch during the dead time between LAMPF macropulses. The chopper consists of 1-m-long push-pull helical-wound slow-wave deflecting structures having an axial pulse velocity of 0.04c, which matches the velocity of the proton beam. The helix ground-planes are biased by a pulser providing push-pull 500-V pulses to deflect the H + beam from the injection channel. In chopping mode A, the helical windings are driven by push-pull, 1000-V, 5-ns pulses delivered by a circuit utilizing avalanche transistors and planar triodes. In mode B, the helical windings are driven by push-pull, 1000-V, 50-ns to 10-μs long pulses, produced by a circuit utilizing beam-power tetrodes and fast SCRs. In both modes, these pulses cancel the ground-plane bias and permit beam pulses to be delivered to the linac

Velocity estimation of an airplane through a single satellite image

Institute of Scientific and Technical Information of China (English)

Zhuxin Zhao; Gongjian Wen; Bingwei Hui; Deren Li

2012-01-01

The motion information of a moving target can be recorded in a single image by a push-broom satellite. A push-broom satellite image is composed of many image lines sensed at different time instants. A method to estimate the velocity of a flying airplane from a single image based on the imagery model of the linear push-broom sensor is proposed. Some key points on the high-resolution image of the plane are chosen to determine the velocity (speed and direction). The performance of the method is tested and verified by experiments using a WorldView-1 image.%The motion information of a moving target can be recorded in a single image by a push-broom satellite.A push-broom satellite image is composed of many image lines sensed at different time instants.A method to estimate the velocity of a flying airplane from a single image based on the imagery model of the linear push-broom sensor is proposed.Some key points on the high-resolution image of the plane are chosen to determine the velocity (speed and direction).The performance of the method is tested and verified by experiments using a WorldView-1 image.

Toward automating Hammersmith pulled-to-sit examination of infants using feature point based video object tracking.

Science.gov (United States)

Dogra, Debi P; Majumdar, Arun K; Sural, Shamik; Mukherjee, Jayanta; Mukherjee, Suchandra; Singh, Arun

2012-01-01

Hammersmith Infant Neurological Examination (HINE) is a set of tests used for grading neurological development of infants on a scale of 0 to 3. These tests help in assessing neurophysiological development of babies, especially preterm infants who are born before (the fetus reaches) the gestational age of 36 weeks. Such tests are often conducted in the follow-up clinics of hospitals for grading infants with suspected disabilities. Assessment based on HINE depends on the expertise of the physicians involved in conducting the examinations. It has been noted that some of these tests, especially pulled-to-sit and lateral tilting, are difficult to assess solely based on visual observation. For example, during the pulled-to-sit examination, the examiner needs to observe the relative movement of the head with respect to torso while pulling the infant by holding wrists. The examiner may find it difficult to follow the head movement from the coronal view. Video object tracking based automatic or semi-automatic analysis can be helpful in this case. In this paper, we present a video based method to automate the analysis of pulled-to-sit examination. In this context, a dynamic programming and node pruning based efficient video object tracking algorithm has been proposed. Pulled-to-sit event detection is handled by the proposed tracking algorithm that uses a 2-D geometric model of the scene. The algorithm has been tested with normal as well as marker based videos of the examination recorded at the neuro-development clinic of the SSKM Hospital, Kolkata, India. It is found that the proposed algorithm is capable of estimating the pulled-to-sit score with sensitivity (80%-92%) and specificity (89%-96%).

Trichotillomania (Hair-Pulling Disorder)

Science.gov (United States)

... pulling Biting, chewing or eating pulled-out hair Playing with pulled-out hair or rubbing it across ... of trichotillomania: Family history. Genetics may play a role in the development of trichotillomania, and the disorder ...

Performance evaluation testing of wells in the gradient control system at a federally operated Confined Disposal Facility using single well aquifer tests, East Chicago, Indiana

Science.gov (United States)

Lampe, David C.; Unthank, Michael D.

2016-12-08

values from the initial air slug test during the 2015 testing period for MW–11A and MW–14A are an order of magnitude less than those derived from the final test during the 2014 testing period indicating the development of a low conductivity skin between the final test of the 2014 testing period and the beginning of the 2015 testing period that created a decrease in the connection of the monitoring well screen to the surrounding aquifer material.Repeated step drawdown and recovery testing of the extraction wells tested during this study provided results that indicate a slight increase in the development of a skin and a decrease in the connectivity of the extraction wells with the Calumet aquifer. Hydraulic conductivity values obtained from the test results were relatively similar in EW–4B and EW–14A but were substantially lower for EW–11C. This difference may be due to the presence of finer grained silt deposits in the area surrounding well nest 11. Skin factors calculated during the step drawdown and recovery analysis were lowest in EW–11C and relatively similar in EW–4B and EW–14A. Calculated skin factors increased slightly in the analysis of data collected in 2015 from that collected in 2014.Comparisons of the specific-capacity values calculated from well development data collected following extraction well installation to those calculated during the single well aquifer tests at EW–4B, EW–14A and EW–11C indicate that the productivity of extraction wells on the CDF property has diminished since 2008. Values calculated for monitoring wells MW–4A, MW–11A, and MW–14A were used to evaluate the decrease in air slug derived hydraulic conductivity for monitoring wells within the groundwater cutoff wall between testing in 2014 and 2015.Results from testing by this study indicate that implementation of an air slug testing regimen of the monitoring wells that control the gradient control system at the CDF throughout the course of a year may help

Effect of the yarn pull-out velocity of shear thickening fluid-impregnated Kevlar fabric on the coefficient of friction

Energy Technology Data Exchange (ETDEWEB)

Aikarami, Sh [Dept. of Mechanical and Aerospace Engineering, Science and Research Branch, Islamic Azad University, Tehran (Iran, Islamic Republic of); Kordani, N. [Dept. of Mechanical Engineering, University of Mazandaran, Mazandaran (Iran, Islamic Republic of); Sadough, Vanini A. [Dept. of Mechanical Engineering, Amirkabir University of Technology, Tehran (Iran, Islamic Republic of); Amiri, H. [Technical Campus, Tehran South Branch, Islamic Azad University, Tehran(Iran, Islamic Republic of)

2016-08-15

This study explains the yarn pull-out process behavior of woven fabrics in relation to their mechanical properties. Empirical research on the relationship between the yarn pull-out behavior and fabric properties are evaluated, along with a detailed comparison of friction between the fabric fibers in static and dynamic modes. Samples are tested in three modes, namely, neat, dissolved liquid, and silica particle- based Shear thickening fluid (STF)-treated fabric. Accordingly, the presence of STF increases friction between the fabrics and the warp and weft yarns, as well as prevents the displacement of the yarns. Increased friction also leads to an increase in the energy absorption of the yarn pull-out process. In this research, the pull-out test has been performed at three different velocities: 50, 250 and 500 mm/min. Results show that increases in the pull-out velocity increase the pull-out force of the neat and dissolved liquid samples. By contrast, the behavior is completely opposite in the STF-treated sample. Comparing the yarn pull-out values indicates that the STF-treated samples have the highest value, which is approximately three times higher than that of the neat sample.

Effect of the yarn pull-out velocity of shear thickening fluid-impregnated Kevlar fabric on the coefficient of friction

International Nuclear Information System (INIS)

Aikarami, Sh; Kordani, N.; Sadough, Vanini A.; Amiri, H.

2016-01-01

This study explains the yarn pull-out process behavior of woven fabrics in relation to their mechanical properties. Empirical research on the relationship between the yarn pull-out behavior and fabric properties are evaluated, along with a detailed comparison of friction between the fabric fibers in static and dynamic modes. Samples are tested in three modes, namely, neat, dissolved liquid, and silica particle- based Shear thickening fluid (STF)-treated fabric. Accordingly, the presence of STF increases friction between the fabrics and the warp and weft yarns, as well as prevents the displacement of the yarns. Increased friction also leads to an increase in the energy absorption of the yarn pull-out process. In this research, the pull-out test has been performed at three different velocities: 50, 250 and 500 mm/min. Results show that increases in the pull-out velocity increase the pull-out force of the neat and dissolved liquid samples. By contrast, the behavior is completely opposite in the STF-treated sample. Comparing the yarn pull-out values indicates that the STF-treated samples have the highest value, which is approximately three times higher than that of the neat sample

Hirschsprung's disease: problems with transition-zone pull-through.

Science.gov (United States)

Ghose, S I; Squire, B R; Stringer, M D; Batcup, G; Crabbe, D C

2000-12-01

It is generally accepted that if surgery for Hirschsprung's disease is to be successful, ganglionic bowel must be anastomosed to the lower rectum or anal canal. Above the aganglionic distal bowel lies a transition zone (TZ) where more subtle abnormalities of innervation are apparent. The significance of this transition zone in respect to the functional outcome of surgery has received little attention. The aim of this study was to identify the incidence of transition zone pull-through (TZPT) in a cohort of children who underwent surgery for Hirschsprung's disease, to identify the reasons why TZPTs occurred, and to identify the functional consequences. The authors report the long-term outcome of these children with emphasis on bowel function and the results of subsequent surgery. A Retrospective study was conducted of children treated at a single institution from 1979 through 1994. TZPT patients were subject to detailed review of surgical records and histopathologic material. Thirteen children were identified with a TZPT. In 12 cases, histopathologic errors contributed to the TZPT: in 5 cases this was caused by single point biopsies missing an asymmetrical TZ, whereas in 7 cases the histopathologic features of the TZ were not recognized. In 1 case the TZPT was caused by surgical error. As a consequence of the TZPT 7 children underwent repeat pull-through. One child is fully continent, one has daytime fecal continence, and 2 others are incontinent. Two children have permanent stomas. One child is clean with antegrade colonic washouts. Repeat pull-throughs were not attempted in 6 children. Two children have achieved full continence, 2 have permanent stomas, 1 is clean with antegrade colonic washouts, and 1 child receives regular suppositories. Transition zone pull-throughs occurred because of a combination of surgical and histopathologic errors. The transition zone may follow an asymmetric course around the circumference of the bowel and may be missed if single

Pull-out test of stud bolts embedded in concrete under an in-plane force

International Nuclear Information System (INIS)

Inada, Y.; Saito, H.; Torita, H.; Takiguchi, K.; Ibe, Y.; Taira, T.

1995-01-01

There are many steel plates with stud bolts embedded in the R C walls of a nuclear reactor building to support equipment and piping. Under a earthquake, the steel plates are submitted to an out-of-plane force due to the inertia force acting upon equipment and piping. Furthermore, the walls are submitted to an in-plane force, and cracks may occur. A large number of experimental studies have been carried out on the pull-out strength of stud bolts embedded in concrete. Few studies have been performed to understand the strength of stud bolts embedded in concrete under an in-plane force and, further, not any one on the strength for concrete under in-plane force simultaneously to stud bolts under out-of-plane force. This paper describes a test performed to understand the pull-out strength determined by this interaction of in-plane and out-of-plane forces. (author). 5 refs., 9 figs., 5 tabs

Isotopic tracers of sources, wells and of CO2 reactivity in geological reservoirs

International Nuclear Information System (INIS)

Assayag, N.

2006-12-01

The aim of this research works consisted in studying the behaviour of the carbonate system (dissolved inorganic carbon: DIC) following a CO 2 injection (artificial or natural), in geological reservoirs. One part of the study consisted in improving an analytical protocol for the measurement of δ 13 C DIC and DIC, using a continuous flow mass spectrometer. As a first study, we have focused our attention on the Pavin Lake (Massif Central, France). Owing to its limnologic characteristics (meromictic lake) and a deep volcanic CO 2 contribution, it can be viewed as a natural analogue of reservoir storing important quantities of CO 2 in the bottom part. Isotopic measurements (δ 18 O, δ 13 C DIC) allowed to better constrain the dynamics of the lake (stratification, seasonal variations), the magnitudes of biological activities (photosynthesis, organic matter decay, methane oxidation, methano-genesis), carbon sources (magmatic, methano-genetic), and the hydrological budgets (sub-lacustrine inputs). The second study was conducted on the Lamont-Doherty test well site (NY, USA). It includes an instrumental borehole which cuts through most of the section of the Palisades sill and into the Newark Basin sediments. Single well push-pull tests were performed: a test solution containing conservative tracers and a reactive tracer (CO 2 ) was injected at a permeable depth interval located in basaltic and meta sedimentary rocks. After an incubation period, the test solution/groundwater mixture was extracted from the hydraulically isolated zone. Isotopic measurements (δ 18 O, δ 13 C DIC) confronted to chemical data (major elements) allowed to investigate the extent of in-situ CO 2 -water-rock interactions: essentially calcite dissolution and at a lesser extend silicate dissolution...and for one of the test, CO 2 degassing. (author)

Estimates of ambient groundwater velocity in the alluvium south of Yucca Mountain from single-well tracer tests

International Nuclear Information System (INIS)

Reimus, P.W.; Umari, M.J.; Roback, R.; Earle, John; Darnell, Jon; Farnham, Irene

2002-01-01

The saturated alluvium located south of Yucca Mountain, Nevada is expected to serve as the final barrier to radionuclide transport from the proposed high-level nuclear waste repository at Yucca Mountain. The alluvium will act as a barrier if radionuclides breach the engineered barriers in the repository, move through the unsaturated zone beneath the repository to the water table, and then migrate through saturated volcanic tuffs to the alluvium. Three single-well injection-withdrawal tracer tests were conducted between December 2000 and April 2001 in the saturated alluviuni at NC-EWDP-19D1, a Nye County-Early Warning Drilling Program well located about 18 km south of Yucca Mountain. The tests had the objectives of (1) distinguishing between a single- and a dual-porosity conceptual radionuclide transport model for the alluvium, and (2) obtaining estimates of ambient groundwater velocity in the alluvium.

Novel silicone compatible cross-linkers for controlled functionalization of PDMS networks

DEFF Research Database (Denmark)

Madsen, Frederikke Bahrt; Daugaard, Anders Egede; Hvilsted, Søren

2013-01-01

. In order to improve the dielectric properties of PDMS a novel system is developed where push-pull dipoles are grafted to a new silicone compatible cross-linker. The grafted cross-linkers are prepared by reaction of two different push-pull dipole alkynes as well as a fluorescent alkyne with the new azide...

Yarn Pull-Out as a Mechanism for Dissipation of Ballistic Impact Energy in Kevlar KM-2 Fabric, Part 1: Quasi-Static Characterization of Yarn Pull-Out

National Research Council Canada - National Science Library

Kirkwood, Keith

2004-01-01

.... This study reports the effects of fabric length, number of yarns pulled, arrangement of yarns, and transverse tension on the force-displacement curves for yarn pull-out tests on Kevlar KM-2 fabric...

Optical pulling of airborne absorbing particles and smut spores over a meter-scale distance with negative photophoretic force

Energy Technology Data Exchange (ETDEWEB)

Lin, Jinda; Hart, Adam G.; Li, Yong-qing, E-mail: liy@ecu.edu [Department of Physics, East Carolina University, Greenville, North Carolina 27858-4353 (United States)

2015-04-27

We demonstrate optical pulling of single light-absorbing particles and smut spores in air over a meter-scale distance using a single collimated laser beam based on negative photophoretic force. The micron-sized particles are pulled towards the light source at a constant speed of 1–10 cm/s in the optical pulling pipeline while undergoing transverse rotation at 0.2–10 kHz. The pulled particles can be manipulated and precisely positioned on the entrance window with an accuracy of ∼20 μm, and their chemical compositions can be characterized with micro-Raman spectroscopy.

Hair Pulling (Trichotillomania)

Science.gov (United States)

... for Families - Vietnamese Spanish Facts for Families Guide Hair Pulling (Trichotillomania) No. 96; Reviewed July 2013 It ... for children and adolescents to play with their hair. However, frequent or obsessive hair pulling can lead ...

Free energy profiles from single-molecule pulling experiments.

Science.gov (United States)

Hummer, Gerhard; Szabo, Attila

2010-12-14

Nonequilibrium pulling experiments provide detailed information about the thermodynamic and kinetic properties of molecules. We show that unperturbed free energy profiles as a function of molecular extension can be obtained rigorously from such experiments without using work-weighted position histograms. An inverse Weierstrass transform is used to relate the system free energy obtained from the Jarzynski equality directly to the underlying molecular free energy surface. An accurate approximation for the free energy surface is obtained by using the method of steepest descent to evaluate the inverse transform. The formalism is applied to simulated data obtained from a kinetic model of RNA folding, in which the dynamics consists of jumping between linker-dominated folded and unfolded free energy surfaces.

Energy requirements of tire pulling.

Science.gov (United States)

Fredriksen, Per M; Mamen, Asgeir

2017-10-01

We have investigated the effect using walking poles and pulling tires at 4 and 6 km·h-1 (1.11 and 1.67 m·s-1) speeds on oxygen uptake (V̇O2) and heart rate. Eleven subjects, 6 males, with a mean (SD) age of 25.2 (6.9) years participated in field tests involving walking without poles, walking with poles and tire pulling with poles. Increasing the load caused the largest increases in energy demand, more than 4 MET. Speed increase also caused substantial energy increase, approximately 4 MET. Increasing the inclination only modestly increased the oxygen uptake, approximately 2 MET. In both level walking and uphill walking, using poles marginally increased oxygen uptake compared to working without poles. Pulling one tire (12.5 kg) required an oxygen uptake of 27 (4) mL·kg-1·min-1 at 4 km·h-1 and 0% inclination. Adding one more tire (6 kg) drove the oxygen uptake further up to 39 (4) mL·kg-1·min-1. This is close to the requirement of level running at 10.5 km·h-1. Pulling both tires at 6 km·h-1 and 5% inclination required a V̇O2 of 54 (6) mL·kg-1·min-1, equal to running uphill at 5% inclination and 12.5 km·h-1 speed. Heart rate rose comparably with oxygen uptake. At 4 km·h-1 and 0% inclination the increase was 29 bpm, from 134 (21) to 163 (22) bpm when going from pulling one tire to two tires. In the hardest exercise, 6 km·h-1 and 5% inclination, heart rate reached 174 (14) bpm. The study showed that tire pulling even at slow speeds has an energy requirement that is so large that the activity may be feasible as endurance training.

Failure conditions from push-out tests of a steel-concrete joint: experimental results

Czech Academy of Sciences Publication Activity Database

Helincks, P.; De Corte, W.; Klusák, Jan; Seitl, Stanislav; Boel, V.; De Schutter, G.

488-489, - (2012), s. 714-717 ISSN 1013-9826. [International Conference on Fracture and Damage Mechanics - FDM 2011 /10./. Dubrovník, 19.09.2011-21.09.2011] R&D Projects: GA ČR GAP108/10/2049 Institutional research plan: CEZ:AV0Z20410507 Keywords : steel-concrete joint * push-out test * shear bond strength Subject RIV: JL - Materials Fatigue, Friction Mechanics

Tracer SWIW tests in propped and un-propped fractures: parameter sensitivity issues, revisited

Science.gov (United States)

Ghergut, Julia; Behrens, Horst; Sauter, Martin

2017-04-01

Single-well injection-withdrawal (SWIW) or 'push-then-pull' tracer methods appear attractive for a number of reasons: less uncertainty on design and dimensioning, and lower tracer quantities required than for inter-well tests; stronger tracer signals, enabling easier and cheaper metering, and shorter metering duration required, reaching higher tracer mass recovery than in inter-well tests; last not least: no need for a second well. However, SWIW tracer signal inversion faces a major issue: the 'push-then-pull' design weakens the correlation between tracer residence times and georeservoir transport parameters, inducing insensitivity or ambiguity of tracer signal inversion w. r. to some of those georeservoir parameters that are supposed to be the target of tracer tests par excellence: pore velocity, transport-effective porosity, fracture or fissure aperture and spacing or density (where applicable), fluid/solid or fluid/fluid phase interface density. Hydraulic methods cannot measure the transport-effective values of such parameters, because pressure signals correlate neither with fluid motion, nor with material fluxes through (fluid-rock, or fluid-fluid) phase interfaces. The notorious ambiguity impeding parameter inversion from SWIW test signals has nourished several 'modeling attitudes': (i) regard dispersion as the key process encompassing whatever superposition of underlying transport phenomena, and seek a statistical description of flow-path collectives enabling to characterize dispersion independently of any other transport parameter, as proposed by Gouze et al. (2008), with Hansen et al. (2016) offering a comprehensive analysis of the various ways dispersion model assumptions interfere with parameter inversion from SWIW tests; (ii) regard diffusion as the key process, and seek for a large-time, asymptotically advection-independent regime in the measured tracer signals (Haggerty et al. 2001), enabling a dispersion-independent characterization of multiple

Directional preference in dogs: Laterality and "pull of the north".

Science.gov (United States)

Adámková, Jana; Svoboda, Jan; Benediktová, Kateřina; Martini, Sabine; Nováková, Petra; Tůma, David; Kučerová, Michaela; Divišová, Michaela; Begall, Sabine; Hart, Vlastimil; Burda, Hynek

2017-01-01

Laterality is a well described phenomenon in domestic dogs. It was shown that dogs, under calm Earth's magnetic field conditions, when marking their home ranges, tend to head about north- or southwards and display thus magnetic alignment. The question arises whether magnetic alignment might be affected or even compromised by laterality and vice versa. We tested the preference of dogs to choose between two dishes with snacks that were placed left and right, in different compass directions (north and east, east and south, south and west or west and north) in front of them. Some dogs were right-lateral, some left-lateral but most of them were ambilateral. There was a preference for the dish placed north compared to the one placed east of the dog ("pull of the north"). This effect was highly significant in small and medium-sized breeds but not in larger breeds, highly significant in females, in older dogs, in lateralized dogs but less significant or not significant in males, younger dogs, or ambilateral dogs. Laterality and "pull of the north" are phenomena which should be considered in diverse tasks and behavioral tests with which dogs or other animals might be confronted. The interaction and possible conflict between lateralization and "pull of the north" might be also considered as a reason for shifted magnetic alignment observed in different animal species in different contexts.

Directional preference in dogs: Laterality and "pull of the north"

Science.gov (United States)

Adámková, Jana; Svoboda, Jan; Benediktová, Kateřina; Martini, Sabine; Nováková, Petra; Tůma, David; Kučerová, Michaela; Divišová, Michaela; Begall, Sabine; Hart, Vlastimil

2017-01-01

Laterality is a well described phenomenon in domestic dogs. It was shown that dogs, under calm Earth's magnetic field conditions, when marking their home ranges, tend to head about north- or southwards and display thus magnetic alignment. The question arises whether magnetic alignment might be affected or even compromised by laterality and vice versa. We tested the preference of dogs to choose between two dishes with snacks that were placed left and right, in different compass directions (north and east, east and south, south and west or west and north) in front of them. Some dogs were right-lateral, some left-lateral but most of them were ambilateral. There was a preference for the dish placed north compared to the one placed east of the dog ("pull of the north"). This effect was highly significant in small and medium-sized breeds but not in larger breeds, highly significant in females, in older dogs, in lateralized dogs but less significant or not significant in males, younger dogs, or ambilateral dogs. Laterality and “pull of the north” are phenomena which should be considered in diverse tasks and behavioral tests with which dogs or other animals might be confronted. The interaction and possible conflict between lateralization and "pull of the north" might be also considered as a reason for shifted magnetic alignment observed in different animal species in different contexts. PMID:28945773

Twinning behavior in the Ti-5at.% Al single crystals during cyclic loading along [0001

International Nuclear Information System (INIS)

Xiao Lin

2005-01-01

Cyclic deformation behavior of Ti-5at.% Al single crystals subjected to pull-push cyclic load along [0001] crystallographic orientation was studied. A higher cyclic stress response was displayed in the Ti-5Al single crystal oriented for [0001] than that oriented for single prism slip. Optical microscopy and transmission electron microscopy examinations show that twinning is a dominant plastic deformation mode in the single crystals during cycling. Trace analysis of prepolished surfaces was used to identify the twin systems primarily responsible for deformation. The major twin type observed was {101-bar 2}, {112-bar 2}, {101-bar 1} and {112-bar 1}. slip was observed in the neighboring region of twins in the fatigued specimens. The activation of multiple twinning systems contributed to the higher cyclic saturation stress in Ti-5Al single crystals oriented for [0001

Effects of pushing techniques during the second stage of labor: A randomized controlled trial.

Science.gov (United States)

Koyucu, Refika Genç; Demirci, Nurdan

2017-10-01

Spontaneous pushing is a method that is used in the management of the second stage of labor and suggested to be more physiological for the mother and infant. The present study aims to evaluate the effects of pushing techniques on the mother and newborn. This randomized prospective study was performed between June 2013-March 2014 in a tertiary maternity clinic in Istanbul. 80 low risk, nulliparous cases were randomized to pushing groups. Valsalva pushing group was told to hold their breath while pushing. No visual-verbal instructions were given to spontaneous pushing group and they were encouraged to push without preventing respiration. Demographic data, second stage period, perineal laceration rates, fetal heart rate patterns, presence of meconium stained amniotic liquid, newborn APGAR scores, POP-Q examination and Q-tip test results were evaluated in these cases. The second stage of labor was significantly longer with spontaneous pushing. Decrease in Hb levels in valsalva pushing group was determined to be higher than spontaneous pushing group. An increased urethral mobility was observed in valsalva pushing group. Although the duration of the second stage of labor was longer compared to valsalva pushing technique, women were able to give birth without requiring any verbal or visual instruction, without exceeding the limit value of two hours and without affecting fetal wellness and neonatal results. Copyright © 2017. Published by Elsevier B.V.

Accurate electrostatic and van der Waals pull-in prediction for fully clamped nano/micro-beams using linear universal graphs of pull-in instability

Science.gov (United States)

Tahani, Masoud; Askari, Amir R.

2014-09-01

In spite of the fact that pull-in instability of electrically actuated nano/micro-beams has been investigated by many researchers to date, no explicit formula has been presented yet which can predict pull-in voltage based on a geometrically non-linear and distributed parameter model. The objective of present paper is to introduce a simple and accurate formula to predict this value for a fully clamped electrostatically actuated nano/micro-beam. To this end, a non-linear Euler-Bernoulli beam model is employed, which accounts for the axial residual stress, geometric non-linearity of mid-plane stretching, distributed electrostatic force and the van der Waals (vdW) attraction. The non-linear boundary value governing equation of equilibrium is non-dimensionalized and solved iteratively through single-term Galerkin based reduced order model (ROM). The solutions are validated thorough direct comparison with experimental and other existing results reported in previous studies. Pull-in instability under electrical and vdW loads are also investigated using universal graphs. Based on the results of these graphs, non-dimensional pull-in and vdW parameters, which are defined in the text, vary linearly versus the other dimensionless parameters of the problem. Using this fact, some linear equations are presented to predict pull-in voltage, the maximum allowable length, the so-called detachment length, and the minimum allowable gap for a nano/micro-system. These linear equations are also reduced to a couple of universal pull-in formulas for systems with small initial gap. The accuracy of the universal pull-in formulas are also validated by comparing its results with available experimental and some previous geometric linear and closed-form findings published in the literature.

On push-forward representations in the standard gyrokinetic model

International Nuclear Information System (INIS)

Miyato, N.; Yagi, M.; Scott, B. D.

2015-01-01

Two representations of fluid moments in terms of a gyro-center distribution function and gyro-center coordinates, which are called push-forward representations, are compared in the standard electrostatic gyrokinetic model. In the representation conventionally used to derive the gyrokinetic Poisson equation, the pull-back transformation of the gyro-center distribution function contains effects of the gyro-center transformation and therefore electrostatic potential fluctuations, which is described by the Poisson brackets between the distribution function and scalar functions generating the gyro-center transformation. Usually, only the lowest order solution of the generating function at first order is considered to explicitly derive the gyrokinetic Poisson equation. This is true in explicitly deriving representations of scalar fluid moments with polarization terms. One also recovers the particle diamagnetic flux at this order because it is associated with the guiding-center transformation. However, higher-order solutions are needed to derive finite Larmor radius terms of particle flux including the polarization drift flux from the conventional representation. On the other hand, the lowest order solution is sufficient for the other representation, in which the gyro-center transformation part is combined with the guiding-center one and the pull-back transformation of the distribution function does not appear

On push-forward representations in the standard gyrokinetic model

Energy Technology Data Exchange (ETDEWEB)

Miyato, N., E-mail: miyato.naoaki@jaea.go.jp; Yagi, M. [Japan Atomic Energy Agency, 2-116 Omotedate, Obuchi, Rokkasho, Aomori 039-3212 (Japan); Scott, B. D. [Max-Planck-Institut für Plasmaphysik, D-85748 Garching (Germany)

2015-01-15

Two representations of fluid moments in terms of a gyro-center distribution function and gyro-center coordinates, which are called push-forward representations, are compared in the standard electrostatic gyrokinetic model. In the representation conventionally used to derive the gyrokinetic Poisson equation, the pull-back transformation of the gyro-center distribution function contains effects of the gyro-center transformation and therefore electrostatic potential fluctuations, which is described by the Poisson brackets between the distribution function and scalar functions generating the gyro-center transformation. Usually, only the lowest order solution of the generating function at first order is considered to explicitly derive the gyrokinetic Poisson equation. This is true in explicitly deriving representations of scalar fluid moments with polarization terms. One also recovers the particle diamagnetic flux at this order because it is associated with the guiding-center transformation. However, higher-order solutions are needed to derive finite Larmor radius terms of particle flux including the polarization drift flux from the conventional representation. On the other hand, the lowest order solution is sufficient for the other representation, in which the gyro-center transformation part is combined with the guiding-center one and the pull-back transformation of the distribution function does not appear.

Full scale model push-off test of reinforced concrete block with 51 mm dia. deformed steel bars

International Nuclear Information System (INIS)

Aoyagi, Y.

1981-01-01

The conclusions of this study are as follows; (1) The equation previously derived from small scale specimens, to predict the shear strength of push-off specimens including both initially cracked and uncracked, can conservatively estimate the experimental data of full scale specimens to the same extent as small scale ones. (2) The equation previously derived from small scale specimens, to predict the shear strength of initially cracked push-off specimens with reinforcements inclined to the shear plane, agrees reasonably well with the experimental data of full scale speciemens. (3) The concrete strength and yield strength of reinforcement theoretically set the balanced reinforcement ratio of the shear area above which the shear strength of specimens is constant. (4) The theoretical shear strength of push-off specimens overestimates the experimental data by about 25%. (orig./HP)

[Development of Biliary Contrast Agents Remote Pushing Device].

Science.gov (United States)

Zhu, Haoyang; Dong, Dinghui; Luo, Yu; Ren, Fenggang; Zhang, Jing; Tan, Wenjun; Shi, Aihua; Hu, Liangshuo; Wu, Rongqian; Lyu, Yi

2018-01-30

A biliary contrast agents pushing device, including a syringe pushing system and a remote controller is introduced. The syringe pushing system comprises an injector card slot, a support platform and an injection bolus fader. A 20 mL syringe can be fitted on the syringe pushing system and kept with the ground about 30 degree. This system can perform air bubble pumping back and contrast agents bolus injection as well as speed adjustment. Remote controller is an infrared remote control which can start and stop the syringe pushing system. With this device, the remote controlled cholangiography technology can be achieved, which can not only protect doctors from X-ray radiation but also improve the traditional T-tube cholangiography and the contrast effect, reduce postoperative complications in patients as well. The application of this device will improve the current diagnosis and treatment system, the device will benefit the majority of doctors and patients.

A sled push stimulus potentiates subsequent 20-m sprint performance.

Science.gov (United States)

Seitz, Laurent B; Mina, Minas A; Haff, G Gregory

2017-08-01

The objective of this study was to examine the potentiating effects of performing a single sprint-style sled push on subsequent unresisted 20m sprint performance. Randomized crossover design. Following a familiarization session, twenty rugby league players performed maximal unresisted 20m sprints before and 15s, 4, 8 and 12min after a single sled push stimulus loaded with either 75 or 125% body mass. The two sled push conditions were performed in a randomized order over a one-week period. The fastest sprint time recorded before each sled push was compared to that recorded at each time point after to determine the post-activation potentiation (PAP) effect. After the 75% body mass sled push, sprint time was 0.26±1.03% slower at the 15s time point (effect size [ES]=0.07) but faster at the 4 (-0.95±2.00%; ES=-0.22), 8 (-1.80±1.43%; ES=-0.42) and 12 (-1.54±1.54%; ES=-0.36)min time points. Sprint time was slower at all the time points after the 125% body mass sled (1.36±2.36%-2.59±2.90%; ESs=0.34-0.64). Twenty-meter sprint performance is potentiated 4-12min following a sled push loaded with 75% body mass while it is impaired after a 125% body mass sled. These results are of great importance for coaches seeking to potentiate sprint performance with the sled push exercise. Copyright © 2017 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

Does delayed pushing in the second stage of labor impact perinatal outcomes?

Science.gov (United States)

Frey, Heather A; Tuuli, Methodius G; Cortez, Sarah; Odibo, Anthony O; Roehl, Kimberly A; Shanks, Anthony L; Macones, George A; Cahill, Alison G

2012-11-01

To estimate maternal, neonatal, and labor outcomes associated with delayed pushing. A retrospective cohort study of all consecutive women admitted to a single institution in labor at term who reached the second stage of labor. Pregnancies with multiple fetuses or major anomalies were excluded. Delayed pushing was defined as initiation of pushing ≥60 minutes after complete dilatation. Primary outcome was mode of delivery. Multivariable logistic regression was used to control for confounding. Of the 5290 women who met inclusion criteria, 471 (8.9%) employed delayed pushing, and 4819 (91.1%) pushed immediately. Delayed pushing was associated with increased rates of cesarean, operative vaginal delivery, maternal fever, and lower arterial cord pH. Duration of the second stage and length of time spent pushing were significantly longer with delayed pushing. Delayed pushing is associated with lower rates of spontaneous vaginal delivery and increased adverse maternal and neonatal outcomes. Thieme Medical Publishers 333 Seventh Avenue, New York, NY 10001, USA.

Single well techniques

International Nuclear Information System (INIS)

Drost, W.

1983-01-01

The single well technique method includes measurement of parameters of groundwater flow in saturated rock. For determination of filtration velocity the dilution of radioactive tracer is measured, for direction logging the collimeter is rotated in the probe linked with the compass. The limiting factor for measurement of high filtration velocities is the occurrence of turbulent flow. The single well technique is used in civil engineering projects, water works and subsurface drainage of liquid waste from disposal sites. The radioactive tracer method for logging the vertical fluid movement in bore-holes is broadly used in groundwater survey and exploitation. (author)

Study on Single-yarn Pullout Test of Ballistic Resistant Fabric under Different Preloads

Science.gov (United States)

Fang, Q. C.; Lei, Z. K.; Y Qin, F.; Li, W. K.; Bai, R. X.

2017-12-01

During bullet penetrating fabric, the pull-out force of yarn in fabric is related to the impact resistance of fabric when the yarn is pulled out from the fabric. The complex uncrimping and friction slip behavior occur during the yarn pullout process, which is critical to learn the impact resistance of fabric. Based on digital image correlation technique, the deformation behavior of Kevlar 49 fabric subjected to preload during the single-yarn pullout process was studied in this paper. The pullout force and displacement curve shows a straight rise and an oscillated decrease. In the linear rise stage, the yarn uncrimping causes a static friction effect. The maximum of the pullout force is not linearly increased with the preload. In the oscillating descending stage, the local descent of the pullout force indicates that the yarn end is gradually withdrawn from the fabric, and the local rise indicates that the yarn end moves to the next weft/warp interaction until the yarn is completely pulled out. The shear deformation of fabric corresponds to the single-yarn pullout process.

Optical Pushing: A Tool for Parallelized Biomolecule Manipulation

NARCIS (Netherlands)

Sitters, G.; Laurens, N.; de Rijk, E.J.; Kress, H.; Peterman, E.J.G.; Wuite, G.J.L.

2016-01-01

The ability to measure and manipulate single molecules has greatly advanced the field of biophysics. Yet, the addition of more single-molecule tools that enable one to measure in a parallel fashion is important to diversify the questions that can be addressed. Here we present optical pushing (OP), a

Ground reaction force characteristics of Tai Chi push hand.

Science.gov (United States)

Chang, Yao-Ting; Chang, Jia-Hao; Huang, Chen-Fu

2014-01-01

Push Hand is an advanced training technique for the Yang-style old frame 108 forms Tai Chi Chuan. It is performed by two practitioners. To clarify how people use forces during Push Hand training, it is important to review the ground reaction force (GRF). Here, we quantify the characteristics of the GRF during Push Hand training. Kinematic data and GRF data from 10 Tai Chi Chuan practitioners (29.9 ± 7.87 years) were synchronously recorded using a three-dimensional motion analysis system (200 frames · s(-1)) and three-dimensional force plates (1000 Hz). The resultant GRF for both feet for the 0%, 50% and 100% phases of attack and defence were compared to body weight using a paired-samples t-test. The differences in the resultant GRF between the 0%, 50% and 100% phases of attack and defence were tested by one-way repeated-measures ANOVA. The significance level was set to 0.05. The total resultant GRF was almost equal to the participant's body weight in push hand. This result was consistent throughout the entire push hand process. Our results revealed that the GRF was comparable to the body weight, implying that practitioners do not push or resist their opponents during the push hand process.

Friction Pull Plug and Material Configuration for Anti-Chatter Friction Pull Plug Weld

Science.gov (United States)

Littell, Justin Anderson (Inventor)

2016-01-01

A friction pull plug is provided for use in forming a plug weld in a hole in a material. The friction pull plug includes a shank and a series of three frustoconical sections. The relative sizes of the sections assure that a central one of the sections defines the initial contact point between the hole's sides. The angle defined by the central one of the sections reduces or eliminates chatter as the plug is pulled into the hole.

An in vitro Comparison of Bond Strength of Different Sealers/Obturation Systems to Root Dentin Using the Push-Out Test at 2 Weeks and 3 Months after Obturation.

Science.gov (United States)

Yap, Wai Ying; Che Ab Aziz, Zeti Adura; Azami, Noor Hayati; Al-Haddad, Afaf Yahya; Khan, Asfand Ali

2017-01-01

To evaluate the push-out bond strength and failure modes of different sealers/obturation systems to intraradicular dentin at 2 weeks and 3 months after obturation compared to AH Plus®/gutta-percha. A total of 180 root slices from 60 single-canal anterior teeth were prepared and assigned to 5 experimental groups (n = 36 in each group), designated as G1 (AH Plus®/gutta-percha), G2 (TotalFill BC™ sealer/BC-coated gutta-percha), G3 (TotalFill BC™ sealer/gutta-percha), G4 (EndoREZ® sealer/EndoREZ®-coated gutta-percha), and G5 (EndoREZ® sealer/gutta-percha). Push-out bond strengths of 18 root slices in each group were assessed at 2 weeks and the other 18 at 3 months after obturation using a universal testing machine. Data were analyzed using repeated measures ANOVA. An independent t test was used to compare the mean push-out bond strength for each group at 2 weeks and 3 months after obturation. The mean push-out bond strengths of G4 and G5 were significantly lower than those of G1, G2, and G3 (p strengths of G2 (3.69 ± 1.20 MPa) and G3 (2.84 ± 0.83 MPa) were higher at 3 months compared to 2 weeks after obturation (G2: 1.74 ± 0.43 MPa, G3: 1.33 ± 0.29 MPa). The TotalFill BC™ obturation system (G2) and the TotalFill BC™ sealer/gutta-percha (G3) showed comparable bond strength to AH Plus®. Their bond strength increased over time, whereas the EndoREZ® obturation system (G4) and EndoREZ sealer (G5) had low push-out bond strength which decreased over time. © 2017 The Author(s) Published by S. Karger AG, Basel.

Effects of Different Relative Loads on Power Performance During the Ballistic Push-up.

Science.gov (United States)

Wang, Ran; Hoffman, Jay R; Sadres, Eliahu; Bartolomei, Sandro; Muddle, Tyler W D; Fukuda, David H; Stout, Jeffrey R

2017-12-01

Wang, R, Hoffman, JR, Sadres, E, Bartolomei, S, Muddle, TWD, Fukuda, DH, and Stout, JR. Effects of different relative loads on power performance during the ballistic push-up. J Strength Cond Res 31(12): 3411-3416, 2017-The purpose of this investigation was to examine the effect of load on force and power performance during a ballistic push-up. Sixty (24.5 ± 4.3 years, 1.75 ± 0.07 m, and 80.8 ± 13.5 kg) recreationally active men who participated in this investigation completed all testing and were included in the data analysis. All participants were required to perform a 1 repetition maximum bench press, and ballistic push-ups without external load (T1), with 10% (T2) and 20% (T3) of their body mass. Ballistic push-ups during T2 and T3 were performed using a weight loaded vest. Peak and mean force, power, as well as net impulse and flight time were determined for each ballistic push-up. Peak and mean force were both significantly greater (p ballistic push-up, regardless of the participants' level of strength.

Understanding Why Students Drop Out of High School, According to Their Own Reports

Directory of Open Access Journals (Sweden)

Jonathan Jacob Doll

2013-10-01

Full Text Available Research on school dropout extends from early 20th-century pioneers until now, marking trends of causes and prevention. However, specific dropout causes reported by students from several nationally representative studies have never been examined together, which, if done, could lead to a better understanding of the dropout problem. Push, pull, and falling out factors provide a framework for understanding dropouts. Push factors include school-consequence on attendance or discipline. Pull factors include out-of-school enticements like jobs and family. Finally, falling out factors refer to disengagement in students not caused by school or outside pulling factors. Since 1966, most nationally representative studies depicted pull factors as ranking the highest. Also, administrators in one study corroborated pull out factors for younger dropouts, not older ones, while most recent research cites push factors as highest overall. One rationale for this change is a response to rising standards from No Child Left Behind (NCLB, which can be ultimately tested only by future dropout research.

The effects of biting and pulling on the forces generated during feeding in the Komodo dragon (Varanus komodoensis).

Science.gov (United States)

D'Amore, Domenic C; Moreno, Karen; McHenry, Colin R; Wroe, Stephen

2011-01-01

In addition to biting, it has been speculated that the forces resulting from pulling on food items may also contribute to feeding success in carnivorous vertebrates. We present an in vivo analysis of both bite and pulling forces in Varanus komodoensis, the Komodo dragon, to determine how they contribute to feeding behavior. Observations of cranial modeling and behavior suggest that V. komodoensis feeds using bite force supplemented by pulling in the caudal/ventrocaudal direction. We tested these observations using force gauges/transducers to measure biting and pulling forces. Maximum bite force correlates with both body mass and total body length, likely due to increased muscle mass. Individuals showed consistent behaviors when biting, including the typical medial-caudal head rotation. Pull force correlates best with total body length, longer limbs and larger postcranial motions. None of these forces correlated well with head dimensions. When pulling, V. komodoensis use neck and limb movements that are associated with increased caudal and ventral oriented force. Measured bite force in Varanus komodoensis is similar to several previous estimations based on 3D models, but is low for its body mass relative to other vertebrates. Pull force, especially in the ventrocaudal direction, would allow individuals to hunt and deflesh with high success without the need of strong jaw adductors. In future studies, pull forces need to be considered for a complete understanding of vertebrate carnivore feeding dynamics.

Failure conditions from push out tests of a steel-concrete joint: fracture mechanics approach

Czech Academy of Sciences Publication Activity Database

Klusák, Jan; Seitl, Stanislav; De Corte, W.; Helincks, P.; Boel, V.; De Schutter, G.

488-489, - (2012), s. 710-713 ISSN 1013-9826. [International Conference on Fracture and Damage Mechanics - FDM 2011 /10./. Dubrovník, 19.09.2011-21.09.2011] R&D Projects: GA ČR GAP108/10/2049 Institutional research plan: CEZ:AV0Z20410507 Keywords : Push out test * generalized linear elastic fracture mechanics * bi-material notch Subject RIV: JL - Materials Fatigue, Friction Mechanics

33 CFR 90.3 - Pushing vessel and vessel being pushed: Composite unit.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Pushing vessel and vessel being... HOMELAND SECURITY INLAND NAVIGATION RULES INLAND RULES: INTERPRETATIVE RULES § 90.3 Pushing vessel and vessel being pushed: Composite unit. Rule 24(b) of the Inland Rules states that when a pushing vessel and...

33 CFR 82.3 - Pushing vessel and vessel being pushed: Composite unit.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Pushing vessel and vessel being... HOMELAND SECURITY INTERNATIONAL NAVIGATION RULES 72 COLREGS: INTERPRETATIVE RULES § 82.3 Pushing vessel and vessel being pushed: Composite unit. Rule 24(b) of the 72 COLREGS states that when a pushing vessel and a...

The effect of a slack-pulling device in reducing operator physiological workload during log winching operations.

Science.gov (United States)

Spinelli, Raffaele; Aalmo, Giovanna Ottaviani; Magagnotti, Natascia

2015-01-01

The authors conducted a comparative test to determine whether the introduction of a hydraulic slack puller allowed reducing the physiological workload of operators assigned to log winching tasks. The tests were conducted in northern Italy, on the mountains near Como. The study involved five volunteer subjects, considered representatives of the regional logging workforce. Physiological workload was determined by measuring the operators' heart rate upon completion of specific tasks. The slack puller improved the efficiency of downhill winching, since it allowed a single operator to pull out the cable on his own, without requiring the assistance of a colleague. However, introduction of the slack puller did not result in any reductions of operator physiological workload. The main stressor when working on a steep slope is moving up and down the slope: pulling a cable is only a secondary stressor. Any measures targeting secondary stressors are unlikely to produce dramatic reductions of operator workload.

The use of horizontal wells for subsurface soil and aquifer remediation

International Nuclear Information System (INIS)

May, D.W.

1994-01-01

The use of directionally controlled horizontal drilling for environmental restoration had its genesis in 1988 when two horizontal remediation wells were drilled at the Savannah River Nuclear Facility near Aiken, South Carolina. Since that time, horizontal remediation wells have been drilled at several Department of Energy and Department of Defense sites as well as on several commercial sites across the country. Directional drilling technology applied to ''Near Surface Horizontal Environmental Drilling'' comes from the oil and gas industry, the utility/pipeline river crossing industry and to a lesser extent the mining industry. Rig designs vary from very small track or wheel mounted rigs using 10 feet (3 meters) drill pipe and having less than 2,500 ft. lb. (3,400 N-m) of torque and 15,000 lb. (67 kN) of push/pull force to extremely large trailer mounted rigs with torques exceeding 60,000 ft. lb. (81,400 N-m) and over 500,000 lb. (2,200 kN) of pull. Vertical depths of horizontal wells drilled to-date have exceeded 250 feet (75 m), but the great majority of contaminant plumes are located at depths of less than 50 feet (15 m). Horizontal well displacements have exceeded 1000 feet (300 m) but most of the projects cover less than 400 feet (120 m). Wells can be drilled ''blind'' (terminate in the earth) or exit back up the earth on the other side of the plume from the drill rig

Study on cord/rubber interface at elevated temperatures by H-pull test method

Science.gov (United States)

Jamshidi, M.; Afshar, F.; Mohammadi, N.; Pourmahdian, S.

2005-08-01

Cords are used as reinforcing materials in rubber compounds. To increase cord/rubber interfacial adhesion, they are coated by an adhesive (usually based on resorcinol-formaldehyde-latex). These composites are used in many sectors such as tire and belt industries. Cord/rubber adhesion strength is an important aspect to determine the durability of system. Due to temperature increase during running tires, the adhesion energy becomes different from initial one. To study cord/rubber interface at elevated temperatures, H-adhesion test method was used. H-pull test is a simple method for adhesion evaluation at ambient temperature, so it is usually used for material quality control. In this research, cord/rubber systems were vulcanized at different temperatures and H-adhesion of samples were evaluated at elevated temperatures. Also cord/rubber interface was studied by ATR analyze to determine interfacial interactions kind.

Single-well tracer methods for hydrogeologic evaluation of target aquifers

International Nuclear Information System (INIS)

Hall, S.H.

1994-11-01

Designing an efficient well field for an aquifer thermal energy storage (ATES) project requires measuring local groundwater flow parameters as well as estimating horizontal and vertical inhomogeneity. Effective porosity determines the volume of aquifer needed to store a given volume of heated or chilled water. Ground-water flow velocity governs the migration of the thermal plume, and dispersion and heat exchange along the flow path reduces the thermal intensity of the recovered plume. Stratigraphic variations in the aquifer will affect plume dispersion, may bias the apparent rate of migration of the plume, and can prevent efficient hydraulic communication between wells. Single-well tracer methods using a conservative flow tracer such as bromide, along with pumping tests and water-level measurements, provide a rapid and cost-effective means for estimating flow parameters. A drift-and-pumpback tracer test yields effective porosity and flow velocity. Point-dilution tracer testing, using new instrumentation for downhole tracer measurement and a new method for calibrating the point-dilution test itself, yields depth-discrete hydraulic conductivity as it is affected by stratigraphy, and can be used to estimate well transmissivity. Experience in conducting both drift-and-pumpback and point-dilution tests at three different test sites has yielded important information that highlights both the power and the limitations of the single-well tracer methods. These sites are the University of Alabama Student Recreation Center (UASRC) ATES well field and the VA Medical Center (VA) ATES well field, both located in Tuscaloosa, Alabama, and the Hanford bioremediation test site north of Richland, Washington

Consumer-oriented functional food development: how well do functional disciplines reflect the 'voice of the consumer'?

NARCIS (Netherlands)

Kleef, van P.W.; Trijp, van J.C.M.; Luning, P.A.; Jongen, W.M.F.

2002-01-01

Food innovation can have its source in either superior understanding of consumer demand (pull) or in superiority at the supply side (science and technology push). However, in either case market success depends on the degree to which the new product reflects unmet consumer needs. The present study

Human push capability.

Science.gov (United States)

Barnett, Ralph L; Liber, Theodore

2006-02-22

Use of unassisted human push capability arises from time to time in the areas of crowd and animal control, the security of locked doors, the integrity of railings, the removal of tree stumps and entrenched vehicles, the manoeuvering of furniture, and athletic pursuits such as US football or wrestling. Depending on the scenario, human push capability involves strength, weight, weight distribution, push angle, footwear/floor friction, and the friction between the upper body and the pushed object. Simple models are used to establish the relationships among these factors.

Growth of Bi 12SiO 20 single crystals by the pulling-down method with continuous feeding

Science.gov (United States)

Maida, Shigeru; Higuchi, Mikio; Kodaira, Kohei

1999-09-01

Bi 12SiO 20 single crystals were successfully grown by the pulling-down method with continuous feeding. As-grown crystals were amber in color and transparent, and had no cracks or inclusions. A crystal with homogeneous composition was obtained from Bi-rich feed powder having a composition of 14.1 mol% SiO 2, whereas precipitates of Bi 4Si 3O 12 were observed on the surface of a crystal grown with stoichiometric powder. The shape of the solid-liquid interface during the crystal growth was estimated to be almost flat, which was favorable to avoid core formation. Average dislocation density was 4×10 3/cm 2, which was comparable to that of Bi 12SiO 20 crystals grown by the Czochralski method.

Pull-pull position control of dual motor wire rope transmission.

Science.gov (United States)

Guo, Quan; Jiao, Zongxia; Yan, Liang; Yu, Qian; Shang, Yaoxing

2016-08-01

Wire rope transmission is very efficient because of the small total moving object mass. The wire rope could only transmit pulling force. Therefore it has to be kept in a tightened state during transmission; in high speed applications the dynamic performance depends on the rope's stiffness, which can be adjusted by the wire rope tension. To improve the system dynamic performance output, this paper proposes a novel pull-pull method based on dual motors connected by wire ropes, for precise, high speed position control applications. The method can regulate target position and wire rope tension simultaneously. Wire ropes remain in a pre-tightening state at all times, which prevents the influence of elasticity and reduces the position tracking error in the changing direction process. Simulations and experiments were conducted; the results indicate that both position precision and superior dynamic performance can be synchronously achieved. The research is relevant to space craft precision pointing instruments.

The effects of biting and pulling on the forces generated during feeding in the Komodo dragon (Varanus komodoensis.

Directory of Open Access Journals (Sweden)

Domenic C D'Amore

Full Text Available In addition to biting, it has been speculated that the forces resulting from pulling on food items may also contribute to feeding success in carnivorous vertebrates. We present an in vivo analysis of both bite and pulling forces in Varanus komodoensis, the Komodo dragon, to determine how they contribute to feeding behavior. Observations of cranial modeling and behavior suggest that V. komodoensis feeds using bite force supplemented by pulling in the caudal/ventrocaudal direction. We tested these observations using force gauges/transducers to measure biting and pulling forces. Maximum bite force correlates with both body mass and total body length, likely due to increased muscle mass. Individuals showed consistent behaviors when biting, including the typical medial-caudal head rotation. Pull force correlates best with total body length, longer limbs and larger postcranial motions. None of these forces correlated well with head dimensions. When pulling, V. komodoensis use neck and limb movements that are associated with increased caudal and ventral oriented force. Measured bite force in Varanus komodoensis is similar to several previous estimations based on 3D models, but is low for its body mass relative to other vertebrates. Pull force, especially in the ventrocaudal direction, would allow individuals to hunt and deflesh with high success without the need of strong jaw adductors. In future studies, pull forces need to be considered for a complete understanding of vertebrate carnivore feeding dynamics.

Pulled elbow in children.

Science.gov (United States)

Yamanaka, Syunsuke; Goldman, Ran D

2018-06-01

Question Our practice is seeing children with relatively minor injuries to their elbows, with a history of "swinging" them when their hands are being held to cross the road. Nothing is usually found on a physical examination. I know that this is likely a "pulled elbow." Can we manage this in the clinic setting rather than sending the family to the emergency department? What would be the best course of action in the clinic setting? Answer Pulled elbow, also called nursemaid's elbow , is a radial head subluxation caused by axial traction or a sudden pull of the extended pronated arm, and it is a very common phenomenon. The practice of swinging children while holding their hands should be abandoned. In the case of pulled elbow, the child usually avoids moving the affected arm, holding it close to his or her body, without considerable pain, and no obvious swelling or deformity can be seen. While a fracture should be excluded, pulled elbow can usually be identified based on this presentation. The reduction procedure can easily be done in the office setting, with an 80% success rate and no complications. The hyperpronation maneuver (holding the elbow at 90° and then firmly pronating the wrist) to reduce pulled elbow has been found to be better than a supination-flexion maneuver (holding the elbow at 90° with one hand, supinating and flexing the elbow rapidly with the other) and should be exercised first. When 2 trials of reduction are unsuccessful, the child's arm should be splinted and the family should be sent for further evaluation. Copyright© the College of Family Physicians of Canada.

Efficient {pi} electrons delocalization in prospective push-pull non-linear optical chromophore 4-[N,N-dimethylamino]-4'-nitro stilbene (DANS): A vibrational spectroscopic study

Energy Technology Data Exchange (ETDEWEB)

Vijayakumar, T.; Hubert Joe, I. [Centre for Molecular and Biophysics Research, Department of Physics, Mar Ivanios College, Thiruvananthapuram 695 015, Kerala (India); Reghunadhan Nair, C.P. [Polymers and Special Chemicals Division, Vikram Sarabhai Space Centre, Thiruvananthapuram 695 022, Kerala (India); Jayakumar, V.S. [Centre for Molecular and Biophysics Research, Department of Physics, Mar Ivanios College, Thiruvananthapuram 695 015, Kerala (India)], E-mail: vsjk@vsnl.net

2008-01-22

A comprehensive investigation on the intramolecular charge transfer (ICT) of an efficient {pi}-conjugated potential push-pull NLO chromophore, 4-[N,N-dimethylamino]-4'-nitro stilbene (DANS), from a strong electron-donor group (dimethylamino-N(CH{sub 3}){sub 2}) to a strong electron-acceptor group (nitro-NO{sub 2}) through the {pi}-conjugated bridge (trans-stilbene) has been carried out from their vibrational spectra. The NIR FT-Raman and FT-IR spectra supported by the density functional theory (DFT) quantum chemical computations have been employed to analyze the effects of intramolecular charge transfer on the geometries and the vibrational modes contributing to the linear electro-optic effect of the organic NLO material. It has been observed that the changes in the endocyclic and exocyclic angles result from the charge-transfer interaction of the phenyl ring and the amino group in the electron-donor side of the NLO chromophore. The strongest vibrational modes contributing to the electro-optic effect have been identified and examined from the concurrent IR and Raman activation of {nu}(C=C/C-C) mode, ring C=C stretching modes, in-plane deformation modes, nitro modes and the umbrella mode of methyl groups. Furthermore, the splitting of the vinyl stretching modes and the electronic effects such as hyperconjugation and backdonation on the methyl hydrogen atoms causing the decrease of stretching frequencies and infrared intensities have also been analyzed in detail. The effect of frontier orbitals transition of electron density transfer and the influence of planarity between the phenyl rings of the stilbene moiety on the first hyperpolarizability have also been discussed.

MEMS and mil/aero: technology push and market pull

Science.gov (United States)

Clifford, Thomas H.

2001-04-01

MEMS offers attractive solutions to high-density fluidics, inertial, optical, switching and other demanding military/aerospace (mil/aero) challenges. However, full acceptance must confront the realities of production-scale producibility, verifiability, testability, survivability, as well as long-term reliability. Data on these `..ilities' are crucial, and are central in funding and deployment decisions. Similarly, mil/aero users must highlight specific missions, environmental exposures, and procurement issues, as well as the quirks of its designers. These issues are particularly challenging in MEMS, because of the laws of physics and business economics, as well as the risks of deploying leading-edge technology into no-fail applications. This paper highlights mil/aero requirements, and suggests reliability/qualification protocols, to guide development effort and to reassure mil/aero users that MEMS labs are mindful of the necessary realities.

Delayed versus immediate pushing in second stage of labor.

Science.gov (United States)

Kelly, Mary; Johnson, Eileen; Lee, Vickie; Massey, Liz; Purser, Debbie; Ring, Karen; Sanderson, Stephanye; Styles, Juanita; Wood, Deb

2010-01-01

Comparison of two different methods for management of second stage of labor: immediate pushing at complete cervical dilation of 10 cm and delayed pushing 90 minutes after complete cervical dilation. This study was a randomized clinical trial in a labor and delivery unit of a not-for-profit community hospital. A sample of 44 nulliparous mothers with continuous epidural anesthesia were studied after random assignment to treatment groups. Subjects were managed with either immediate or delayed pushing during the second stage of labor at the time cervical dilation was complete. The primary outcome measure was the length of pushing during second stage of labor. Secondary outcomes included length of second stage of labor, maternal fatigue and perineal injuries, and fetal heart rate decelerations. Two-tailed, unpaired Student's t-tests and Chi-square analysis were used for data analysis. Level of significance was set at p pushing; N = 16 delayed pushing). The delayed pushing group had significantly shorter amount of time spent in pushing compared with the immediate pushing group (38.9 +/- 6.9 vs. 78.7 +/- 7.9 minutes, respectively, p = .002). Maternal fatigue scores, perineal injuries, and fetal heart rate decelerations were similar for both groups. Delaying pushing for up to 90 minutes after complete cervical dilation resulted in a significant decrease in the time mothers spent pushing without a significant increase in total time in second stage of labor.In clinical practice, healthcare providers sometimes resist delaying the onset of pushing after second stage of labor has begun because of a belief it will increase labor time. This study's finding of a 51% reduction in pushing time when mothers delay pushing for up to 90 minutes, with no significant increase in overall time for second stage of labor, disputes that concern.

Self-Induced Backaction Optical Pulling Force

Science.gov (United States)

Zhu, Tongtong; Cao, Yongyin; Wang, Lin; Nie, Zhongquan; Cao, Tun; Sun, Fangkui; Jiang, Zehui; Nieto-Vesperinas, Manuel; Liu, Yongmin; Qiu, Cheng-Wei; Ding, Weiqiang

2018-03-01

We achieve long-range and continuous optical pulling in a periodic photonic crystal background, which supports a unique Bloch mode with the self-collimation effect. Most interestingly, the pulling force reported here is mainly contributed by the intensity gradient force originating from the self-induced backaction of the object to the self-collimation mode. This force is sharply distinguished from the widely held conception of optical tractor beams based on the scattering force. Also, this pulling force is insensitive to the angle of incidence and can pull multiple objects simultaneously.

10–25 GHz frequency reconfigurable MEMS 5-bit phase shifter using push–pull actuator based toggle mechanism

International Nuclear Information System (INIS)

Dey, Sukomal; Koul, Shiban K

2015-01-01

This paper presents a frequency tunable 5-bit true-time-delay digital phase shifter using radio frequency microelectromechanical system (RF MEMS) technology. The phase shifter is based on the distributed MEMS transmission line (DMTL) concept utilizing a MEMS varactor. The main source of frequency tuning in this work is a bridge actuation mechanism followed by capacitance variation. Two stages of actuation mechanisms (push and pull) are used to achieve a 2:1 tuning ratio. Accurate control of the actuation voltage between the pull to push stages contributes differential phase shift over the band of interest. The functional behavior of the push–pull actuation over the phase shifter application is theoretically established, experimentally investigated and validated with simulation. The phase shifter is fabricated monolithically using a gold based surface micromachining process on an alumina substrate. The individual primary phase-bits (11.25°/22.5°/45°/90°/180°) that are the fundamental building blocks of the complete 5-bit phase shifter are designed, fabricated and experimentally characterized from 10–25 GHz for specific applications. Finally, the complete 5-bit phase shifter demonstrates an average phase error of 4.32°, 2.8°, 1° and 1.58°, an average insertion loss of 3.76, 4.1, 4.2 and 4.84 dB and an average return loss of 11.7, 12, 14 and 11.8 dB at 10, 12, 17.2 and 25 GHz, respectively. To the best of the authors’ knowledge, this is the first reported band tunable stand alone 5-bit phase shifter in the literature which can work over the large spectrum for different applications. The total area of the 5-bit phase shifter is 15.6 mm 2 . Furthermore, the cold-switched reliability of the unit cell and the complete 5-bit MEMS phase shifter are extensively investigated and presented. (paper)

Elastic Properties of Nucleic Acids by Single-Molecule Force Spectroscopy.

Science.gov (United States)

Camunas-Soler, Joan; Ribezzi-Crivellari, Marco; Ritort, Felix

2016-07-05

We review the current knowledge on the use of single-molecule force spectroscopy techniques to extrapolate the elastic properties of nucleic acids. We emphasize the lesser-known elastic properties of single-stranded DNA. We discuss the importance of accurately determining the elastic response in pulling experiments, and we review the simplest models used to rationalize the experimental data as well as the experimental approaches used to pull single-stranded DNA. Applications used to investigate DNA conformational transitions and secondary structure formation are also highlighted. Finally, we provide an overview of the effects of salt and temperature and briefly discuss the effects of contour length and sequence dependence.

Multilevel push pull power converter

DEFF Research Database (Denmark)

2007-01-01

A power converter for converting an input voltage (Vin) into an output voltage (Vout), comprising a first supply potential and a second supply potential established by the input voltage, and at least one primary winding having two terminals, a center tap arranged between the two terminals and con...

In Planta Single-Molecule Pull-Down Reveals Tetrameric Stoichiometry of HD-ZIPIII:LITTLE ZIPPER Complexes.

Science.gov (United States)

Husbands, Aman Y; Aggarwal, Vasudha; Ha, Taekjip; Timmermans, Marja C P

2016-08-01

Deciphering complex biological processes markedly benefits from approaches that directly assess the underlying biomolecular interactions. Most commonly used approaches to monitor protein-protein interactions typically provide nonquantitative readouts that lack statistical power and do not yield information on the heterogeneity or stoichiometry of protein complexes. Single-molecule pull-down (SiMPull) uses single-molecule fluorescence detection to mitigate these disadvantages and can quantitatively interrogate interactions between proteins and other compounds, such as nucleic acids, small molecule ligands, and lipids. Here, we establish SiMPull in plants using the HOMEODOMAIN LEUCINE ZIPPER III (HD-ZIPIII) and LITTLE ZIPPER (ZPR) interaction as proof-of-principle. Colocalization analysis of fluorophore-tagged HD-ZIPIII and ZPR proteins provides strong statistical evidence of complex formation. In addition, we use SiMPull to directly quantify YFP and mCherry maturation probabilities, showing these differ substantially from values obtained in mammalian systems. Leveraging these probabilities, in conjunction with fluorophore photobleaching assays on over 2000 individual complexes, we determined HD-ZIPIII:ZPR stoichiometry. Intriguingly, these complexes appear as heterotetramers, comprising two HD-ZIPIII and two ZPR molecules, rather than heterodimers as described in the current model. This surprising result raises new questions about the regulation of these key developmental factors and is illustrative of the unique contribution SiMPull is poised to make to in planta protein interaction studies. © 2016 American Society of Plant Biologists. All rights reserved.

[Length of pushing efforts: pushing is not playing. Reply to the article of C. Le Ray and F. Audibert].

Science.gov (United States)

Schaal, J-P; Dreyfus, M; Bretelle, F; Carbonne, B; Dupuis, O; Foulhy, C; Goffinet, F; Houfflin-Debarge, V; Langer, B; Martin, A; Mercier, C; Mignon, A; Poulain, P; Simon, A; Teurnier, F; Verspyck, E; Riethmuller, D; Hoffmann, P; Pierre, F

2008-11-01

The aim of this work is to answer constructively to C. Le Ray and F. Audibert who were surprised that the French guidelines recommended an assisted delivery after 30 min pushing, even if the fetal heart rate is reassuring. We first resumed the definition of "second stage of labor", this word including the first phase with no pushing efforts and the second phase with active pushing of the mother. With that definition, the length of the second stage is around 60 min for the primipara and 20 min for the multipara, this length being modified by the use of peridural. We then specified the physiological mechanisms influencing the acidobasic equilibrium during the pushing time. Those mechanisms are difficult to consider because foetal heart rate monitoring is often "lost" during that phase. Altogether, these factors bring incertitude about progressive foetal acidosis and incapacity to diagnose it. Finally, the literature analysis teaches us that increasing the second stage of labor (inactive plus active phases) during the normal pregnancy seems to be at low risk for the foetus within the primiparas, but display a risk for the mother and so might be limited. Comparing the delayed pushing with the immediate pushing only lead us to conclude that delayed pushing is dangerous, as is prolonged second stage. In conclusion, we think that prolonging the second stage of labor is possible but must be by increasing the inactive first phase of the second stage, especially as long as we will not get a noninvasive and reliable method allowing assessing the well-being of the foetus.

A piezo motor based on a new principle with high output force, rigidity and integrity: The Tuna Drive

Science.gov (United States)

Liu, Xiaolong; Lu, Qingyou

2012-11-01

We present a linear piezoelectric motor as simple as one piezoelectric scanner tube (PST) spring-clamping a central shaft at both ends with roughly equal clamping forces. The clamping points are aligned with ±X electrodes at one end and ±Y electrodes at the other end. Thus, the ±X (or ±Y) push-pull motions of the PST can cause the push-pull motions of the clamping points on the shaft (called push-pull rubbing), which reduces the total dynamic friction force at one (or the other) end of the PST. This new piezo motor advances one step by fast push-pull rubbing at one end while slowly retracting the PST followed by fast push-pull rubbing at the other end while slowly elongating the PST. Apart from the obvious advantages of simplicity, rigidity, integrity, etc., we will also show that this motor can produce a large output force, which we believe is because of the huge drop of the clamping friction force when the push-pull rubbing occurs.

Present knowledge about Laboratory Testing of Axial Loading on Suction Caissons

DEFF Research Database (Denmark)

Manzotti, E.; Vaitkunaite, Evelina; Ibsen, Lars Bo

Offshore wind turbines are increasing in both efficiency and size. More economical foundations for such light structures are under investigation, and suction caisson was shown to be particularly suitable for this purpose. In multi-pod foundation configuration, the overturning moment given by loads...... on the structure is resisted by push-pull loads on the vertical axis of each suction caisson. Relevant works where this situation is examined by means of laboratory testing are summarized in this article, then different conclusions are followed by discussion and comparison. In the initial theoretical section...

The influence of the epoxy interlayer on the assessment of failure conditions of push-out test specimens

Czech Academy of Sciences Publication Activity Database

Klusák, Jan; Helincks, P.; Seitl, Stanislav; De Corte, W.; Boel, V.; De Schutter, G.

525-526, č. 1 (2013), s. 61-64 ISSN 1013-9826 R&D Projects: GA ČR GAP108/10/2049; GA ČR(CZ) GAP105/11/1551 Institutional support: RVO:68081723 Keywords : push-out test * generalized fracture mechanics * failure initiation * steel-concrete joint * epoxy adhesive layer Subject RIV: JL - Materials Fatigue, Friction Mechanics

Prone positioning reduces severe pushing behavior: three case studies.

Science.gov (United States)

Fujino, Yuji; Amimoto, Kazu; Sugimoto, Satoshi; Fukata, Kazuhiro; Inoue, Masahide; Takahashi, Hidetoshi; Makita, Shigeru

2016-09-01

[Purpose] Pushing behavior is classically described as a disorder of body orientation in the coronal plane. Most interventions for pushing behavior have focused on correcting the deviation in vertical perception. However, pushing behavior seems to involve erroneous movements associated with excessive motor output by the non-paretic limbs and trunk. The present study aimed to inhibit muscular hyper-activity by placing the non-paretic limbs and trunk in the prone position. [Subjects and Methods] The subjects of the present study were 3 acute stroke patients with severe pushing behavior. The study consisted of the following 3 phases: baseline, intervention, and follow-up. In addition to conventional therapy, patients received relaxation therapy in the prone position for 10 minutes a day over 2 days. The severity of pushing behavior was assessed using the scale for contraversive pushing, and truncal balance was evaluated using the trunk control test. These assessments were performed before and after the baseline phase, and after the intervention and follow-up phases. [Results] At the baseline phase, both scores were poor. Both scores improved after the intervention and follow-up phases, and all the patients could sit independently. [Conclusion] Relaxation therapy in the prone position might ameliorate pushing behavior and impaired truncal balance.

Field Testing of Downgradient Uranium Mobility at an In-Situ Recovery Uranium Mine

Science.gov (United States)

Reimus, P. W.; Clay, J. T.; Rearick, M.; Perkins, G.; Brown, S. T.; Basu, A.; Chamberlain, K.

2015-12-01

In-situ recovery (ISR) mining of uranium involves the injection of O2 and CO2 (or NaHCO3) into saturated roll-front deposits to oxidize and solubilize the uranium, which is then removed by ion exchange at the surface and processed into U3O8. While ISR is economical and environmentally-friendly relative to conventional mining, one of the challenges of extracting uranium by this process is that it leaves behind a geochemically-altered aquifer that is exceedingly difficult to restore to pre-mining geochemical conditions, a regulatory objective. In this research, we evaluated the ability of the aquifer downgradient of an ISR mining area to attenuate the transport of uranium and other problem constituents that are mobilized by the mining process. Such an evaluation can help inform both regulators and the mining industry as to how much restoration of the mined ore zone is necessary to achieve regulatory compliance at various distances downgradient of the mining zone even if complete restoration of the ore zone proves to be difficult or impossible. Three single-well push-pull tests and one cross-well test were conducted in which water from an unrestored, previously-mined ore zone was injected into an unmined ore zone that served as a geochemical proxy for the downgradient aquifer. In all tests, non-reactive tracers were injected with the previously-mined ore zone water to allow the transport of uranium and other constituents to be compared to that of the nonreactive species. In the single-well tests, it was shown that the recovery of uranium relative to the nonreactive tracers ranged from 12-25%, suggesting significant attenuation capacity of the aquifer. In the cross-well test, selenate, molybdate and metavanadate were injected with the unrestored water to provide information on the transport of these potentially-problematic anionic constituents. In addition to the species-specific transport information, this test provided valuable constraints on redox conditions within

Automatic control of oscillatory penetration apparatus

Science.gov (United States)

Lucon, Peter A

2015-01-06

A system and method for controlling an oscillatory penetration apparatus. An embodiment is a system and method for controlling a sonic drill having a displacement and an operating range and operating at a phase difference, said sonic drill comprising a push-pull piston and eccentrics, said method comprising: operating the push-pull piston at an initial push-pull force while the eccentrics are operated at a plurality of different operating frequencies within the operating range of the sonic drill and measuring the displacement at each operating frequency; determining an efficient operating frequency for the material being drilled and operating the eccentrics at said efficient operating frequency; determining the phase difference at which the sonic drill is operating; and if the phase difference is not substantially equal to minus ninety degrees, operating the push-pull piston at another push-pull force.

Single-stage transanal endorectal pull-through for Hirschsprung's disease: perspective from a developing country.

Science.gov (United States)

Pratap, Akshay; Shakya, Vikal Chandra; Biswas, Binay Kumar; Sinha, Arvind; Tiwari, Awadhesh; Agrawal, Chandra Shekhar; Adhikary, Shailesh

2007-03-01

The aim of this study was to evaluate the feasibility, results, and cost-effectiveness of totally transanal endorectal pull-through (TEPT) in the management of rectosigmoid and midsigmoid Hirschsprung's disease (HD) in a low-income country. Between March 2004 and December 2005, 19 children underwent totally TEPT procedure. The patients' ages ranged from 6 days to 13 years. The primary diagnosis in all 19 patients was HD confined to the rectosigmoid region in 15 and midsigmoid in 4. None had a preoperative colostomy. Follow-up period ranged from 4 to 20 months (mean, 8 months). Ages ranged from 0.25 to 65 months, with a mean of 16.24 months. Weights ranged from 3.4 to 13 kg, with a mean of 6.5 kg. Mean time from diagnosis to pull-through procedure was 26 days (range, 6-39 days). The mean length of rectosigmoid resection was 30 cm (range, 20-50 cm). The mean operative time was 95 minutes (range, 75-140 minutes). Mean intraoperative blood loss was 25 mL (range, 15-40 mL). There was one death unrelated to the procedure. One patient had enterocolitis 3 months postoperatively. Average frequency of defecation was 3 (range, 1-6) stools per day. TEPT was associated with a shorter operating time, less blood loss, early return to feeds, and an overall reduced cost. The safety and cost-effective benefits of transanal endorectal pull-through in the treatment of HD are of special interest for a developing country. Our data also suggest that functional outcome following TEPT is highly satisfactory and comparable with other established procedures.

Determination of Fracture System Geometry from Well Testing

International Nuclear Information System (INIS)

Doe, T.W.

1994-01-01

In this paper, the research and development for the description of the hydraulic geometry of fracture networks are discussed. The studies on fracture networks have developed on the premise that the structural geological information on fracture geometries could be used to develop the realistic models of flow. It has been widely recognized that a relatively small portion of natural fracture networks controls a major portion of groundwater flow. The key to efficient network modeling is to identify that portion of networks. It is the main purpose of this paper to discuss the methods for characterizing the hydraulic geometry of fracture flow systems. The methods described in this paper cover three approaches for defining the hydraulic geometry of fracture networks, that is, the determination of conductive fracture frequency in boreholes, the use of transient pressure and flow responses in single holes, and the use of cross hole test to assess connectivity. The information which can be obtained by each test is shown. Flow logging, well test distribution and conductive fracture frequency are discussed. The transient analysis of single hole well test and the cross hole analysis of well test for fracture network geometry are reported. The data taken by various methods together can provide network characterization. (K.I.)

Pull-out bond strength of a self-adhesive resin cement to NaOCl-treated root dentin: effect of antioxidizing agents

Directory of Open Access Journals (Sweden)

Maryam Khoroushi

2014-05-01

Full Text Available Objectives This study evaluated the effect of three antioxidizing agents on pull-out bond strengths of dentin treated with sodium hypochlorite. Materials and Methods Root canals of 75 single-rooted human teeth were prepared. Fifteen teeth were irrigated with normal saline for a negative control group, and the remaining 60 teeth (groups 2 - 5 with 2.5% NaOCl. The teeth in group 2 served as a positive control. Prior to post cementation, the root canals in groups 3 - 5 were irrigated with three antioxidizing agents including 10% rosmarinic acid (RA, Baridge essence, 10% hesperidin (HPN, Sigma, and 10% sodium ascorbate hydrogel (SA, AppliChem. Seventy-five spreaders (#55, taper .02, Produits Dentaires S.A were coated with silica and silanized with the Rocatec system and ceramic bond. All the prepared spreaders were cemented with a self-adhesive resin cement (Bifix SE, Voco Gmbh in the prepared canals. After storage in distilled water (24 h/37℃, the spreaders were pulled out in a universal testing machine at a crosshead speed of 1.0 mm/min. Pull-out strength values were analyzed by one-way ANOVA and Tukey's HSD test (α = 0.05. Results There were significant differences between study groups (p = 0.016. The highest pull-out strength was related to the SA group. The lowest strength was obtained in the positive control group. Conclusions Irrigation with NaOCl during canal preparation decreased bond strength of resin cement to root dentin. Amongst the antioxidants tested, SA had superior results in reversing the diminishing effect of NaOCl irrigation on the bond strength to root dentin.

Single crystal fibers growth of double lithium, lanthanium molybdate and adjustment of a micro-pulling down furnace for high vacuum setup

International Nuclear Information System (INIS)

Silva, Fernando Rodrigues da

2013-01-01

In this work we investigated crystal growth procedures aiming the development of single crystal fiber (SCF) for laser applications. For quality optimization in the fabrication of fluorides SCF a new growth chamber for a micro-pulling down furnace (μ-PD) was constructed targeting the fibers fabrication with strict atmosphere control (high vacuum, gas flux and static atmospheres). Simultaneously, the SCF growth process of rare earth double molybdates was studied. The growth of pure and Nd 3+ -doped SCF of LiLa(MoO 4 ) 2 (LLM) was studied in the range of 0,5 - 10mol% doping. The designed furnace growth chamber with controlled atmosphere was successfully constructed and tested under different conditions. Specially, it was tested with the growth of LiF SFC under CF 4 atmosphere showing the expected results. Transparent and homogeneous SCF of Nd:LLM were grown. In the pure fibers was observed facets formation, however, these defects were minimized after tuning of the growth parameters and additionally with the fibers doping. X-ray analysis showed the crystallization of a single phase (space group I4 1 /a); the optical coherence tomography showed the presence of scattering centers only in regions were some growth stability occurred due to the manual process control. The measured Nd 3+ distribution showed uniform incorporation, indicative of a segregation coefficient close to unity in LLM. The potential laser gain of the system was determined using a numerical solution of the rate equations system for the 805nm, CW pumping regime, showing the maximum laser emission gain at 1.064 μm for a Nd 3+ -doping of 5mol%. (author)

Growth and luminescent properties of the Ce, Pr doped NaCl single crystals grown by the modified micro-pulling-down method

International Nuclear Information System (INIS)

Yokota, Yuui; Yanagida, Takayuki; Fujimoto, Yutaka; Nikl, Martin; Yoshikawa, Akira

2010-01-01

We have investigated luminescent properties of nondope, Ce and Pr doped NaCl [nondope NaCl, Ce:NaCl, Pr:NaCl] single crystals grown by a modified micro-pulling-down method with a removable chamber system. Nondope, Ce 1% and Pr 1% doped NaCl crystals with a single phase of NaCl structure were obtained and the crystals indicated general crystal quality by the X-ray rocking curve measurement. For the nondope NaCl and Pr:NaCl crystals, the transmittance spectra indicated almost more than 60% in the wavelength from 200 to 800 nm and an absorption of Ce 3+ ion was observed in the transmittance spectrum of Ce:NaCl crystal. The emission spectrum originated from Ce 3+ 5d-4f transition appeared around 300 nm in the photoluminescence spectrum and the decay time was 19.7 ns.

Push Attack: Binding Virtual and Real Identities Using Mobile Push Notifications

Directory of Open Access Journals (Sweden)

Pierpaolo Loreti

2018-01-01

Full Text Available Popular mobile apps use push notifications extensively to offer an “always connected” experience to their users. Social networking apps use them as a real-time channel to notify users about new private messages or new social interactions (e.g., friendship request, tagging, etc.. Despite the cryptography used to protect these communication channels, the strict temporal binding between the actions that trigger the notifications and the reception of the notification messages in the mobile device may represent a privacy issue. In this work, we present the push notification attack designed to bind the physical owners of mobile devices with their virtual identities, even if pseudonyms are used. In an online attack, an active attacker triggers a push notification and captures the notification packets that transit in the network. In an offline attack, a passive attacker correlates the social network activity of a user with the received push notification. The push notification attack bypasses the standard ways of protecting user privacy based on the network layer by operating at the application level. It requires no additional software on the victim’s mobile device.

Pull test performance and correlation with falls risk in Parkinson?s disease

Directory of Open Access Journals (Sweden)

Renato P. Munhoz

2014-08-01

Full Text Available Postural instability (PI and falls are major sources of disability in Parkinson’s disease (PD. Our objectives were to evaluate the correlation between the pull-test (PT scores and falls. Patients underwent a standardized data collection including demographic, clinical data, and the UPDRS scores for falls and the PT. Cases with scores >1 for falls were considered frequent fallers. 264 patients were included with mean age 67.6±10 years, mean age of onset 59.1±10.7 years. Comparison between PT scores versus the proportion of frequent fallers and the mean score of the UPDRS for falls showed that for each increase in the PT score, both parameters were significantly worse, with positive linear relationship. For any abnormal PT score, sensibility and negative predictive value were excellent; specificity and positive predictive value improved with worse PT scores. In conclusion, the PT provides important and reliable information regarding PI and the risk of falls in PD.

Push Recovery for Humanoid Robot in Dynamic Environment and Classifying the Data Using K-Mean

Directory of Open Access Journals (Sweden)

Anubha Parashar

2016-12-01

Full Text Available Push recovery is prime ability that is essential to be incorporated in the process of developing a robust humanoid robot to support bipedalism. In real environment it is very essential for humanoid robot to maintain balance. In this paper we are generating a control system and push recovery controller for humanoid robot walking. We apply different kind of pushes to humanoid robot and the algorithm that can bring a change in the walking stage to sustain walking. The simulation is done in 3D environment using Webots. This paper describes techniques for feature selection to foreshow push recovery for hip, ankle and knee joint. We train the system by K-Mean algorithm and testing is done on crouch data and tested results are reported. Random push data of humanoid robot is collected and classified to see whether push lie in safer region and then tested on given proposed system.

August A. Pulle. 1878-1955

NARCIS (Netherlands)

Lanjouw, J.

1955-01-01

On the 28th of February 1955 Prof. Dr A. A. Pulle died at Utrecht after a long and painful illness. August Adriaan Pulle was born on the 10th of January 1878 at Arnhem, where he also attended the primary and the secundary school. During the later years at the high school his interest in plants was

Modifications of micro-pulling-down method for the growth of selected Li-containing crystals for neutron scintillator and VUV scintillation crystals

Science.gov (United States)

Pejchal, J.; Fujimoto, Y.; Chani, V.; Yanagida, T.; Yokota, Y.; Yoshikawa, A.; Nikl, M.; Beitlerova, A.

2012-12-01

To develop new and efficient neutron scintillator, Ti-doped LiAlO2 single crystal was grown by micro-pulling-down method. The X-ray excited radioluminescence spectra and neutron light yield were measured. Positive effect of Mg codoping on the overall scintillation efficiency was found. The BaLu2F8 single crystal was grown by micro-pulling-down method using low temperature gradient at growth interface and applying quenching immediately after growth process.

EFFICACY OF ADDUCTOR PULL BACK EXERCISE ON PAIN AND FUNCTIONAL DISABILITY FOR SACROILIAC JOINT DYSFUNCTION

Directory of Open Access Journals (Sweden)

Sai Kumar .N

2015-08-01

Full Text Available Background: Sacroiliac joint dysfunction (SIJD is a common problem that causes pain and disability. Adductor pull back exercise is widely used for treating sacroiliac joint dysfunction. No yet research has been directly examined the efficacy of adductor pull back exercise for sacroiliac joint dysfunction. The purpose of the study to find the efficacy of adductor pull back exercise on pain and functional disability for subjects with sacroiliac joint dysfunction. Methods: An experimental study design, 40 subjects with unilateral Sacroiliac joint dysfunction were randomized into two groups: study group (n=20, and control group (n=20. Subjects in study group received adductor pull back exercise along with conventional exercise and Subjects in control group received conventional exercise. The duration of treatment was given for two weeks, three times a day, total six days per week. Outcome measures such as pain was measured using Visual analog scale (VAS, and functional disability was measured using Oswestry Disability Index questionnaire (ODI before and after 2 weeks of the treatment in both the groups. Results: When means were analyzed using Independent ‘t’ test as a parametric and Mann Whitney U test as a non-parametric test, there is a statistically significant improvements in means of VAS, and ODI within the groups. When means were compared using Independent ‘t’ and Mann Whitney U test, there is a significant difference in post-means of VAS and ODI between the groups. Conclusion: The present study concludes that the 2 weeks of adductor pull back exercise along with conventional exercise found statistically and clinically significant effect on improving pain, functional disability for subjects with sacroiliac joint dysfunction. Adductors pull back exercise along with conventional exercise techniques shown to have greater percentage of improvement in improving pain and functional disability for subjects with sacroiliac joint dysfunction.

Residual stress and microstructural behaviour of a shot peened steel in fatigue. An X-ray diffraction study

Energy Technology Data Exchange (ETDEWEB)

Bergstroem, J.

1986-01-01

The surface residual stress behaviour during fatigue of the quenched and tempered medium strength low-alloyed steel SS 2244-05, equivalent to AISI 4140, has been investigated. Notched specimens of shot peened and ground surface conditions were used. The residual stresses were measured by the X-ray diffraction sin/sup 2/psi-method at intervals in the fatigue tests. Fatigue testing was performed with constant load amplitude at nominal pull-push and pull-pull cycling. The effects of peak-load and variable amplitude were also examined. It was found that the residual stress relaxation could be linked to a total mean stress relaxation towards zero, to an extent which is ruled by a softening criteria. Fatigue test data of the shot peened and ground surface conditions are also given. An X-ray diffraction line broadening analysis was undertaken to examine the microstructural behaviour due to fatigue loading and its correlation to the residual stress behaviour. Single-peak analysis with a Voigt-function method was used to estimate the microstructural parameters, domain size and microstrain. Multiple-peak analysis according to the Warren-Averbach method was used to verify the single-peak analysis. The dislocation density was found to decrease depending on the load amplitude, while the dislocation arrangement follows a pattern depending on yield history.

Growth and luminescent properties of the Ce, Pr doped NaCl single crystals grown by the modified micro-pulling-down method

Energy Technology Data Exchange (ETDEWEB)

Yokota, Yuui, E-mail: y-yokota@tagen.tohoku.ac.j [Institute of Multidisciplinary Research for Advanced Materials, Tohoku University/2-1-1, Katahira, Aoba-ku, Sendai (Japan); Yanagida, Takayuki; Fujimoto, Yutaka [Institute of Multidisciplinary Research for Advanced Materials, Tohoku University/2-1-1, Katahira, Aoba-ku, Sendai (Japan); Nikl, Martin [Institute of Physics, Academy of Sciences of the Czech Republic/6253, Prague (Czech Republic); Yoshikawa, Akira [Institute of Multidisciplinary Research for Advanced Materials, Tohoku University/2-1-1, Katahira, Aoba-ku, Sendai (Japan); New Industry Creation Hatchery Center (NICHe), Tohoku University/2-1-1, Katahira, Aoba-ku, Sendai (Japan)

2010-03-15

We have investigated luminescent properties of nondope, Ce and Pr doped NaCl [nondope NaCl, Ce:NaCl, Pr:NaCl] single crystals grown by a modified micro-pulling-down method with a removable chamber system. Nondope, Ce 1% and Pr 1% doped NaCl crystals with a single phase of NaCl structure were obtained and the crystals indicated general crystal quality by the X-ray rocking curve measurement. For the nondope NaCl and Pr:NaCl crystals, the transmittance spectra indicated almost more than 60% in the wavelength from 200 to 800 nm and an absorption of Ce{sup 3+} ion was observed in the transmittance spectrum of Ce:NaCl crystal. The emission spectrum originated from Ce{sup 3+} 5d-4f transition appeared around 300 nm in the photoluminescence spectrum and the decay time was 19.7 ns.

A novel method for direct solder bump pull testing using lead-free solders

Science.gov (United States)

Turner, Gregory Alan

This thesis focuses on the design, fabrication, and evaluation of a new method for testing the adhesion strength of lead-free solders, named the Isotraction Bump Pull method (IBP). In order to develop a direct solder joint-strength testing method that did not require customization for different solder types, bump sizes, specific equipment, or trial-and-error, a combination of two widely used and accepted standards was created. First, solder bumps were made from three types of lead free solder were generated on untreated copper PCB substrates using an in-house fabricated solder bump-on-demand generator, Following this, the newly developed method made use of a polymer epoxy to encapsulate the solder bumps that could then be tested under tension using a high precision universal vertical load machine. The tests produced repeatable and predictable results for each of the three alloys tested that were in agreement with the relative behavior of the same alloys using other testing methods in the literature. The median peak stress at failure for the three solders tested were 2020.52 psi, 940.57 psi, and 2781.0 psi, and were within one standard deviation of the of all data collected for each solder. The assumptions in this work that brittle fracture occurred through the Intermetallic Compound layer (IMC) were validated with the use of Energy-Dispersive X-Ray Spectrometry and high magnification of the fractured surface of both newly exposed sides of the test specimens. Following this, an examination of the process to apply the results from the tensile tests into standard material science equations for the fracture of the systems was performed..

STRENGTH ANALYSIS METHODS OF CIRCULAR PULL BROACH COGS

Directory of Open Access Journals (Sweden)

Cosmin MIRIŢOIU

2010-10-01

Full Text Available A very big importance in a pull broach designing is represented by its mechanic computation, which trots out the pull broach resistance on various blank tooling, pull broach productivity and also the loadings which is subdued to and the stresses that appear during the chipping process. The pull broach geometric complexity leads to one difficulty concerning the resistance computing methods application (and implicitly, simplifying assumptions application. This present study presents a resistance computing of pull broach cogs, which dresses a circular hole trotting out more methods which can be used in this computing, and the teoretic aspects are then trotted out by an example of a numerical computation for a particular case.

Petrothermal heat extraction using a single deviated well (Horstberg, revisited)

Science.gov (United States)

Ghergut, Julia; Behrens, Horst; Vogt, Esther; Bartetzko, Anne; Sauter, Martin

2013-04-01

The single-well tracer test conducted (Behrens et al. 2006) in conjunction with waterfrac experiments at Horstberg is re-examined with a view at four basic issues: why single-well? why fracturing? why tracers? does this only work at Horstberg, or can it work almost anywhere else in the Northern-German sedimentary basin? Heat and tracer transport within a composite reservoir (impermeable matrix + waterfrac + permeable layer), as accessed by a single deviated well, turn out to fit into a surprisingly simple description, as the plain (arithmetic) sum of certain petrothermal-type and aquifer-type contributions, whose weighting relative to each other can vary from site to site, depending upon stratigraphy and upon wellbore geometry. At Horstberg, within the particular formations tested ('Volpriehausen', 'Detfurth', 'Solling', comprising mainly claystone and sandstone layers), thermal lifetime results to be petrothermally-dominated, while tracer residence times prove to be 'aquifer'-dominated. Despite this disparity, the reservoir's thermal lifetime can reliably be predicted from tracer test results. What cannot be determined from waterfrac flow-path tracing is the very waterfrac's aperture. Aperture uncertainty, however, does not impede upon thermal lifetime predictability. The results of the semi-analytical approach are confirmed by numerical simulations using a FE model that includes more details of hydrogeological heterogeneity for the Horstberg site. They are complemented by a parameter sensitivity analysis. ACKNOWLEDGEMENT: This study is funded by MWK Niedersachsen (Lower-Saxony's Science and Culture Ministry) and by Baker Hughes (Celle) within task unit G6 of the Collaborative Research Project 'gebo' ('Geothermal Energy and High-Performance Drilling').

Push-out Bond Strength of Calcium Enriched Mixture Exposed to Alkaline Environment

Directory of Open Access Journals (Sweden)

Sobhnamayan F

2015-09-01

Full Text Available Statement of Problem: Calcium hydroxide which is commonly used as an intracanal medicament, changes the pH of dentin and periradicular tissues to an alkaline pH. In some clinical situations, endodontic reparative cements like calcium enriched mixture cement are used after calcium hydroxide therapy. However, the alkaline pH may affect the physical properties of this cement. Objectives: This study was designed to evaluate the effect of alkaline pH on the push-out bond strength of calcium enriched mixture. Materials and Methods: 80 root slices were prepared from single-rooted human teeth and their lumens were instrumented to achieve a diameter of 1.3mm. Calcium enriched mixture (CEM was mixed according to the manufacturer’s instruction and introduced into the lumens of root slices. The specimens were then randomly divided into 4 groups (n = 20 and wrapped in pieces of gauze soaked in synthetic tissue fluid (STF buffered in potassium hydroxide at pH values of 7.4, 8.4, 9.4, or 10.4. The samples were incubated for 4 days at 37°C. The push-out bond strengths were then measured using a universal testing machine. Failure modes were examined under a light microscope at ×20 magnification. The data were analyzed using one-way analysis of variance and Tukey’s post hoc tests. Results: The greatest (1.41 ± 0.193 MPa and lowest (0.8 ± 0.06 MPa mean push-out bond strengths were observed after exposure to pH values of 7.4 and 8.4, respectively. There were significant differences between the neutral group and the groups with pH of 8.4 (p = 0.008 and 10.4 (p = 0.022. The bond failure was predominantly of cohesive type for all experimental groups. Conclusions: Under the condition of this study, alkaline pH adversely affected the Push-out bond strength of CEM cement.

Particle Engulfment and Pushing

Science.gov (United States)

2001-01-01

As a liquefied metal solidifies, particles dispersed in the liquid are either pushed ahead of or engulfed by the moving solidification front. Similar effects can be seen when the ground freezes and pushes large particles out of the soil. The Particle Engulfment and Pushing (PEP) experiment, conducted aboard the fourth U.S. Microgravity Payload (USMP-4) mission in 1997, used a glass and plastic beads suspended in a transparent liquid. The liquid was then frozen, trapping or pushing the particles as the solidifying front moved. This simulated the formation of advanced alloys and composite materials. Such studies help scientists to understand how to improve the processes for making advanced materials on Earth. The principal investigator is Dr. Doru Stefanescu of the University of Alabama. This image is from a video downlink.

High frequency fatigue test of IN 718 alloy – microstructure and fractography evaluation

Directory of Open Access Journals (Sweden)

J. Belan

2015-01-01

Full Text Available INCONEL alloy 718 is a high-strength, corrosion-resistant nickel chromium material used at -253 °C to 705 °C for production of heat resistant parts of aero jet engine mostly. The fatigue test provided on this kind materials were done via low frequency loading up to this time. Nowadays, needs of results at higher volume of loading cycles leads to high frequency loading with aim to shorten testing time. Fatigue test of experimental material was carried out at frequency 20 kHz with stress ration R = - 1 (push – pull at room temperature. It was found that this superalloy can still fracture after exceeding 108 cycles. Besides fatigue test were microstructural characterisation and scanning electron microscopy (SEM fractography evaluation done.

Push-pull effect on the geometrical, optical and charge transfer properties of disubstituted derivatives of mer-tris(4-hydroxy-1,5-naphthyridinato aluminum (mer-AlND3

Directory of Open Access Journals (Sweden)

Rao Joshi Laxmikanth

2016-01-01

Full Text Available To design innovative and novel optical materials with high mobility, two kinds of disubstituted derivatives for mer-tris(4-hydroxy-1,5-naphthyridinato aluminum (mer-AlND3 with push (EDG–pull (EWG substituents have been designed. The structures of mer-tris(8-EDG-2-EWG-4-hydroxy-1,5-naphthyridinato aluminum (type I and mer-tris(8-EWG-2-EDG-4-hydroxy-1,5-naphthyridinato aluminum (type II in the ground and first excited states have been optimized at the B3LYP/6-31G(D and CIS/6-31G(D level of theory, respectively. It can be seen from frontier molecular orbitals analysis, in all these complexes, the highest occupied molecular orbital (HOMO is localized on the pyridine-4-ol ring of A-ligand while lowest unoccupied molecular orbital (LUMO is on the pyridyl ring of B-ligand in ground state irrespective of electron donor/acceptor substitution present on the ligands similar to that of mer-tris(8-hydroxyquinoline aluminum (mer-Alq3 and parent mer-AlND3.The absorption and emission wavelengths have been evaluated at the TD-PBE0/6-31G(D level and it can be see that all the type I derivatives show blue shift while most of the type II derivatives show red shift compared to mer-AlND3. All the disubstituted complexes have showed hypsochromic shifts in both the absorption and emission spectra when compared with the calculated absorption and emission spectra respectively of mer-Alq3. It can be seen that the reorganization energies of some of the disubstituted derivatives are comparable with mer-Alq3 and these derivatives might be good candidates for emitting materials in OLED.

Muscle Activation during Push-Ups with Different Suspension Training Systems.

Science.gov (United States)

Calatayud, Joaquin; Borreani, Sebastien; Colado, Juan C; Martín, Fernando F; Rogers, Michael E; Behm, David G; Andersen, Lars L

2014-09-01

The purpose of this study was to analyze upper extremity and core muscle activation when performing push-ups with different suspension devices. Young fit male university students (n = 29) performed 3 push-ups each with 4 different suspension systems. Push-up speed was controlled using a metronome and testing order was randomized. Average amplitude of the electromyographic root mean square of Triceps Brachii, Upper Trapezius, Anterior Deltoid, Clavicular Pectoralis, Rectus Abdominis, Rectus Femoris, and Lumbar Erector Spinae was recorded. Electromyographic signals were normalized to the maximum voluntary isometric contraction (MVIC). Electromyographic data were analyzed with repeated-measures analysis of variance with a Bonferroni post hoc. Based upon global arithmetic mean of all muscles analyzed, the suspended push-up with a pulley system provided the greatest activity (37.76% of MVIC; p push-up with a pulley system also provided the greatest triceps brachii, upper trapezius, rectus femoris and erector lumbar spinae muscle activation. In contrast, more stable conditions seem more appropriate for pectoralis major and anterior deltoid muscles. Independent of the type of design, all suspension systems were especially effective training tools for reaching high levels of rectus abdominis activation. Key PointsCompared with standard push-ups on the floor, suspended push-ups increase core muscle activation.A one-anchor system with a pulley is the best option to increase TRICEP, TRAPS, LUMB and FEM muscle activity.More stable conditions such as the standard push-up or a parallel band system provide greater increases in DELT and PEC muscle activation.A suspended push-up is an effective method to achieve high muscle activity levels in the ABS.

Motion in the unstable thoracolumbar spine when spine boarding a prone patient

Science.gov (United States)

Conrad, Bryan P.; Marchese, Diana L.; Rechtine, Glenn R.; Horodyski, MaryBeth

2012-01-01

Introduction Previous research has found that the log roll (LR) technique produces significant motion in the spinal column while transferring a supine patient onto a spine board. The purpose of this project was to determine whether log rolling a patient with an unstable spine from prone to supine with a pulling motion provides better thoracolumbar immobilization compared to log rolling with a push technique. Methods A global instability was surgically created at the L1 level in five cadavers. Two spine-boarding protocols were tested (LR Push and LR Pull). Both techniques entailed performing a 180° LR rotation of the prone patient from the ground to the supine position on the spine board. An electromagnetic tracking device registered motion between the T12 and L2 vertebral segments. Six motion parameters were tracked. Repeated-measures statistical analysis was performed to evaluate angular and translational motion. Results Less motion was produced during the LR Push compared to the LR Pull for all six motion parameters. The difference was statistically significant for three of the six parameters (flexion–extension, axial translation, and anterior–posterior (A–P) translation). Conclusions Both the LR Push and LR Pull generated significant motion in the thoracolumbar spine during the prone to supine LR. The LR Push technique produced statistically less motion than the LR Pull, and should be considered when a prone patient with a suspected thoracolumbar injury needs to be transferred to a long spine board. More research is needed to identify techniques to further reduce the motion in the unstable spine during prone to supine LR. PMID:22330191

Spontaneous pushing to prevent postpartum urinary incontinence: a randomized, controlled trial.

Science.gov (United States)

Low, Lisa Kane; Miller, Janis M; Guo, Ying; Ashton-Miller, James A; DeLancey, John O L; Sampselle, Carolyn M

2013-03-01

The risk for urinary incontinence can be 2.6-fold greater in women after pregnancy and childbirth compared with their never-pregnant counterparts, with the incidence increasing with parity. We tested the hypothesis that the incidence of de novo postpartum urinary incontinence in primiparous women is reduced with the use of spontaneous pushing alone or in combination with perineal massage compared with women who experienced traditional directed pushing for second-stage management. This was a prospective clinical trial enrolling and randomizing 249 women into a four-group design: (1) routine care with coached or directed pushing, (2) spontaneous self-directed pushing, (3) prenatal perineal massage initiated in the third trimester, and (4) the combination of spontaneous pushing plus perineal massage. Self-report of incontinence was assessed using analysis of variance (ANOVA) and covariance (ANCOVA) models in 145 remaining women at 12 months postpartum using the Leakage Index, which is sensitive to minor leakage. No statistical difference in the incidence of de novo postpartum incontinence was found based on method of pushing (spontaneous/directed) (P value = 0.57) or in combination with prenatal perineal massage (P value = 0.57). Fidelity to pushing treatment of type was assessed and between-groups crossover detected. Spontaneous pushing did not reduce the incidence of postpartum incontinence experienced by women 1 year after their first birth due to high cross-over between randomization groups.

The fractography analysis of IN718 alloy after three-point flexure fatigue test

Directory of Open Access Journals (Sweden)

Belan Juraj

2018-01-01

Full Text Available In this study, the high cycle fatigue (HCF properties of IN718 superalloy with given chemical composition were investigated at three-point flexure fatigue test at room temperature. INCONEL alloy 718 is nickel-chromium-iron hardenable alloy and due to its unique combination of mechanical properties (high-strength; corrosion-resistant and so on used for production of heat resistant parts of aero jet engine mostly. Mechanical properties of this alloy are strongly dependent on microstructure and on presence of structural features such are principal strengthening phase gamma double prime, gamma prime and due to its morphology less desired delta phases. The mentioned phases precipitate at various temperature ranges and Nb content as well. The three-point flexure fatigue test was performed on ZWICK/ROELL Amsler 150 HFP 5100 test equipment with approximate loading frequency f=150 Hz. The S – N (Stress – Number of cycles curve was obtained after testing. With the help of scanning electron microscope (SEM, fractography analyses were performed to disclose the fracture features of specimens in different life ranges. The brief comparison of three-point flexure and push-pull fatigue loading modes and its influence on fatigue life is discussed as well.

Pushing the Limit: A Class Project

Science.gov (United States)

Odafe, Victor U.

2012-01-01

Instructors are constantly struggling to help students understand mathematical concepts as well as the relevance of mathematics to the real world. In calculus, students possess misconceptions of the limit concept. "Pushing the Limit" refers to a semester-long calculus class project that required students to read about, interview calculus…

Effect of root canal rinsing protocol on dentin bond strength of two resin cements using three different method of test.

Science.gov (United States)

Khoroushi, Maryam; Sheikhi, Mohammadreza; Khalilian-Gourtani, Amirhossein; Soleimani, Bahram

2016-07-01

Different studies have used different tests to evaluate bond strength of resin cements to root dentin. In this in vitrostudy, three different tests were used to evaluate the bond strength of two resin cements to root dentin using two root dentin irrigation protocols. Ninety-six intact single-rooted teeth were selected for this study. Forty-eight teeth, with a root length of 15mm, were randomly divided into two groups and irrigated with normal saline or 2.5% sodium hypochlorite solutions during root canal preparation, respectively. For each 12 specimens from each group, fiber post #1 was bonded using an etch-and-rinse (Duo-Link) and a self-adhesive (BisCem) resin cement, respectively. After incubation, two specimens were prepared for the push-out test from the middle thirds of the roots. In another 24 teeth, after two 1.5-mm sections were prepared from the middle thirds of the prepared roots, sections of the post were bonded in two subgroups with each of the cements mentioned above and the samples were prepared for the pull-out test. For shear test, the crowns of 48 teeth were cut away, the dentin surfaces were prepared, the two irrigation solutions were used, and the resin cements were bonded. Data collected from the three tests were evaluated by ANOVA, post-hoc Tukey and Weibull tests (α=0.05). There were significant differences in the mean bond strength values between the three bond strength tests (Pstrength in all tests (P>0.05). Under the limitations of the present study, the method of the test used had an effect on the recorded bond strength between the resin cement and root dentin. Cement type and irrigation protocol resulted in similar variations with all the tests. Push-out and shear tests exhibited more coherent results. Bond strength, endodontically treated tooth, fiber post, resin cement, sodium hypochlorite.

Magnetic characterization of superparamagnetic nanoparticles pulled through model membranes.

Science.gov (United States)

Barnes, Allison L; Wassel, Ronald A; Mondalek, Fadee; Chen, Kejian; Dormer, Kenneth J; Kopke, Richard D

2007-01-04

To quantitatively compare in-vitro and in vivo membrane transport studies of targeted delivery, one needs characterization of the magnetically-induced mobility of superparamagnetic iron oxide nanoparticles (SPION). Flux densities, gradients, and nanoparticle properties were measured in order to quantify the magnetic force on the SPION in both an artificial cochlear round window membrane (RWM) model and the guinea pig RWM. Three-dimensional maps were created for flux density and magnetic gradient produced by a 24-well casing of 4.1 kilo-Gauss neodymium-iron-boron (NdFeB) disc magnets. The casing was used to pull SPION through a three-layer cell culture RWM model. Similar maps were created for a 4 inch (10.16 cm) cube 48 MGOe NdFeB magnet used to pull polymeric-nanoparticles through the RWM of anesthetized guinea pigs. Other parameters needed to compute magnetic force were nanoparticle and polymer properties, including average radius, density, magnetic susceptibility, and volume fraction of magnetite. A minimum force of 5.04 x 10(-16) N was determined to adequately pull nanoparticles through the in-vitro model. For the guinea pig RWM, the magnetic force on the polymeric nanoparticles was 9.69 x 10-20 N. Electron microscopy confirmed the movement of the particles through both RWM models. As prospective carriers of therapeutic substances, polymers containing superparamagnetic iron oxide nanoparticles were succesfully pulled through the live RWM. The force required to achieve in vivo transport was significantly lower than that required to pull nanoparticles through the in-vitro RWM model. Indeed very little force was required to accomplish measurable delivery of polymeric-SPION composite nanoparticles across the RWM, suggesting that therapeutic delivery to the inner ear by SPION is feasible.

Modelling the Dynamics of Ships with Different Propulsion Systems for Control Purpose

Directory of Open Access Journals (Sweden)

Gierusz Witold

2016-01-01

Full Text Available Two different propulsion systems are analyzed from point of view of future control applications. The traditional one consists of a pushing single screw propeller and a blade rudder. The other system is based on pod (pods: pulling or pushing ones. The equations describing forces and moments generated in both systems, are presented. Exemplary results of a simulation in comparison to the real-time experiments for two ships are also shown.

Gait strategy changes with acceleration to accommodate the biomechanical constraint on push-off propulsion.

Science.gov (United States)

Oh, Keonyoung; Baek, Juhyun; Park, Sukyung

2012-11-15

To maintain steady and level walking, push-off propulsion during the double support phase compensates for the energy loss through heel strike collisions in an energetically optimal manner. However, a large portion of daily gait activities also contains transient gait responses, such as acceleration or deceleration, during which the observed dominance of the push-off work or the energy optimality may not hold. In this study, we examined whether the push-off propulsion during the double support phase served as a major energy source for gait acceleration, and we also studied the energetic optimality of accelerated gait using a simple bipedal walking model. Seven healthy young subjects participated in the over-ground walking experiments. The subjects walked at four different constant gait speeds ranging from a self-selected speed to a maximum gait speed, and then they accelerated their gait from zero to the maximum gait speed using a self-selected acceleration ratio. We measured the ground reaction force (GRF) of three consecutive steps and the corresponding leg configuration using force platforms and an optical marker system, respectively, and we compared the mechanical work performed by the GRF during each single and double support phase. In contrast to the model prediction of an increase in the push-off propulsion that is proportional to the acceleration and minimizes the mechanical energy cost, the push-off propulsion was slightly increased, and a significant increase in the mechanical work during the single support phase was observed. The results suggest that gait acceleration occurs while accommodating a feasible push-off propulsion constraint. Copyright © 2012 Elsevier Ltd. All rights reserved.

Third invitational well-testing symposium: well testing in low permeability environments

Energy Technology Data Exchange (ETDEWEB)

Doe, T.W.; Schwarz, W.J. (eds.)

1981-03-01

The testing of low permeability rocks is common to waste disposal, fossil energy resource development, underground excavation, and geothermal energy development. This document includes twenty-six papers and abstracts, divided into the following sessions: opening session, case histories and related phenomena, well test design in low permeability formations, analysis and interpretation of well test data, and instrumentation for well tests. Separate abstracts were prepared for 15 of the 16 papers; the remaining paper has been previously abstracted. (DLC)

Third invitational well-testing symposium: well testing in low permeability environments

International Nuclear Information System (INIS)

Doe, T.W.; Schwarz, W.J.

1981-03-01

The testing of low permeability rocks is common to waste disposal, fossil energy resource development, underground excavation, and geothermal energy development. This document includes twenty-six papers and abstracts, divided into the following sessions: opening session, case histories and related phenomena, well test design in low permeability formations, analysis and interpretation of well test data, and instrumentation for well tests. Separate abstracts were prepared for 15 of the 16 papers; the remaining paper has been previously abstracted

Ultrasonic Nondestructive Evaluation of Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) During Large-Scale Load Testing and Rod Push-Out Testing

Science.gov (United States)

Johnston, Patrick H.; Juarez, Peter D.

2016-01-01

The Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) is a structural concept developed by the Boeing Company to address the complex structural design aspects associated with a pressurized hybrid wing body (HWB) aircraft configuration. The HWB has long been a focus of NASA's environmentally responsible aviation (ERA) project, following a building block approach to structures development, culminating with the testing of a nearly full-scale multi-bay box (MBB), representing a segment of the pressurized, non-circular fuselage portion of the HWB. PRSEUS is an integral structural concept wherein skins, frames, stringers and tear straps made of variable number of layers of dry warp-knit carbon-fiber stacks are stitched together, then resin-infused and cured in an out-of-autoclave process. The PRSEUS concept has the potential for reducing the weight and cost and increasing the structural efficiency of transport aircraft structures. A key feature of PRSEUS is the damage-arresting nature of the stitches, which enables the use of fail-safe design principles. During the load testing of the MBB, ultrasonic nondestructive evaluation (NDE) was used to monitor several sites of intentional barely-visible impact damage (BVID) as well as to survey the areas surrounding the failure cracks after final loading to catastrophic failure. The damage-arresting ability of PRSEUS was confirmed by the results of NDE. In parallel with the large-scale structural testing of the MBB, mechanical tests were conducted of the PRSEUS rod-to-overwrap bonds, as measured by pushing the rod axially from a short length of stringer.

Laparoscopically assisted anorectal pull-through for rectovestibular ...

African Journals Online (AJOL)

Laparoscopically assisted anorectal pull-through for rectovestibular fistula. Taha Alkhatrawi, Radi Elsherbini, Waheed Alturkistani. Abstract. Purpose Laparoscopically assisted anorectal pull-through (LAARP) has been described as an alternative to posterior sagittal anorectoplasty for the surgical treatment of rectourethral ...

Methods of pushing during vaginal delivery and pelvic floor and perineal outcomes: a review.

Science.gov (United States)

de Tayrac, Renaud; Letouzey, Vincent

2016-12-01

Over the past 20 years, several randomized studies have compared Valsalva and spontaneous pushing techniques during vaginal delivery. This review summarizes current medical knowledge concerning their maternal and fetal consequences, focusing on pelvic and perineal outcomes. We selected nine randomized controlled trials comparing Valsalva and spontaneous pushing, and a secondary analysis of a randomized controlled trial comparing different methods of perineal protection. Two trials showed that spontaneous pushing reduces the risk of perineal tears, but no firm conclusions can be drawn given the heterogeneity and inconsistent results of these studies. Conflicting results have been reported regarding the duration of the second stage of labor. Pushing technique does not seem to affect episiotomy, instrumental delivery or cesarean rates. Maternal satisfaction seems to be better after spontaneous pushing. Spontaneous pushing appears to have no adverse effects on neonatal well being, and one study showed a significant improvement in prenatal fetal parameters during the expulsive phase. Valsalva and spontaneous pushing techniques currently appear comparable in terms of duration, pelvic floor, perineal, and neonatal outcomes. In the absence of strong evidence in favor of either technique, the decision should be guided by patient preference and the clinical situation. Additional, well-designed randomized controlled trials are required.

Arterial cord blood lactate at birth correlates with duration of pushing efforts.

Science.gov (United States)

Dessolle, Lionel; Lebrec, Jeremie; Daraï, Emile

2010-01-01

To evaluate the impact of the duration of pushing efforts on arterial cord blood lactate values. This was a prospective observational study of 124 consecutive normal vaginal deliveries in a tertiary teaching hospital. Arterial cord blood lactate was determined immediately at birth with a test strip method. Univariate and multivariate analyses were performed to check for clinical determinants of lactate levels. The main measure was lactate according to the duration of pushing efforts. Arterial cord lactates increased significantly and were strongly correlated with the duration of pushing efforts, independent of gestational age and birthweight. Women pushing for more than 20 min had higher arterial cord blood lactates (4.9 +/- 1.4 vs. 3.3 +/- 1.16 mM, respectively) and a higher rate of lactates >6 mM (18 vs. 3%) than those pushing for less than 20 min. At normal delivery, arterial cord blood lactates increase significantly with the duration of pushing efforts. Pushing for more than 20 min is associated with an increased risk of metabolic acidosis in the neonate. Further studies are required to evaluate the clinical significance of these observations. 2009 S. Karger AG, Basel.

Single well injection withdrawal tests (SWIW) in fractured rock. Some aspects on interpretation

International Nuclear Information System (INIS)

Neretnieks, Ivars

2007-08-01

Single-Well-Injection-Withdrawal, SWIW, tests are used to try to extract information on fracture apertures, sorption and diffusion properties and dispersion information in individual fractures. It is done by injecting a given amount of traced water into an isolated fracture. After a waiting period water is withdrawn from the fracture and the tracer concentration is measured. The concentration time curve is fitted to a model and the parameter values quantifying the different interaction mechanisms are determined. A number of different mechanisms influence the recovery of the tracer. One or more of the following mechanisms are considered. They include: dispersion due to velocity differences, sorption on fracture surface and on infill, diffusion in rock fragments in the fracture, diffusion between 'streamlines', diffusion into rock matrix and other stagnant water volumes, sorption kinetics and slow drift of the plume caused by the natural gradient. Many of the interaction mechanisms can influence the recovery curve in a similar way. For example, diffusion into rock matrix water and into stagnant water in the fracture adjacent to the flowing channels cannot be distinguished if only one tracer is used. Tracers with different properties can in principle be used but they will encounter different parts of the fracture, the sorbing tracer will move out less from the injection point than a nonsorbing tracer will. Diffusion and sorption in small particles in the flowpath can influence the recovery curve in a similar way as rock matrix diffusion does. Dispersion caused by diffusion between 'streamlines', Taylor dispersion, can give very different results in channels of different shapes. Such dispersion effects can be difficult to distinguish from matrix diffusion effects. Dispersion coefficients obtained in a SWIW test may have little relation to dispersion of a tracer moving from A to B. This is partly due to the different mechanisms and partly due to different time scales

Single well injection withdrawal tests (SWIW) in fractured rock. Some aspects on interpretation

Energy Technology Data Exchange (ETDEWEB)

Neretnieks, Ivars [Dept. of Chemical Engineering and Technology, Royal Inst. of Technology, Stockholm (Sweden)

2007-08-15

Single-Well-Injection-Withdrawal, SWIW, tests are used to try to extract information on fracture apertures, sorption and diffusion properties and dispersion information in individual fractures. It is done by injecting a given amount of traced water into an isolated fracture. After a waiting period water is withdrawn from the fracture and the tracer concentration is measured. The concentration time curve is fitted to a model and the parameter values quantifying the different interaction mechanisms are determined. A number of different mechanisms influence the recovery of the tracer. One or more of the following mechanisms are considered. They include: dispersion due to velocity differences, sorption on fracture surface and on infill, diffusion in rock fragments in the fracture, diffusion between 'streamlines', diffusion into rock matrix and other stagnant water volumes, sorption kinetics and slow drift of the plume caused by the natural gradient. Many of the interaction mechanisms can influence the recovery curve in a similar way. For example, diffusion into rock matrix water and into stagnant water in the fracture adjacent to the flowing channels cannot be distinguished if only one tracer is used. Tracers with different properties can in principle be used but they will encounter different parts of the fracture, the sorbing tracer will move out less from the injection point than a nonsorbing tracer will. Diffusion and sorption in small particles in the flowpath can influence the recovery curve in a similar way as rock matrix diffusion does. Dispersion caused by diffusion between 'streamlines', Taylor dispersion, can give very different results in channels of different shapes. Such dispersion effects can be difficult to distinguish from matrix diffusion effects. Dispersion coefficients obtained in a SWIW test may have little relation to dispersion of a tracer moving from A to B. This is partly due to the different mechanisms and partly due to

The impact of pushed output on accuracy and fluency of Iranian EFL learners’ speaking

Directory of Open Access Journals (Sweden)

Aram Reza Sadeghi Beniss

2014-07-01

Full Text Available The current study attempted to establish baseline quantitative data on the impacts of pushed output on two components of speaking (i.e., accuracy and fluency. To achieve this purpose, 30 female EFL learners were selected from a whole population pool of 50 based on the standard test of IELTS interview and were randomly assigned into an experimental group and a control group. The participants in the experimental group received pushed output treatment while the students in the control group received non-pushed output instruction. The data were collected through IELTS interview and then the interview of each participant was separately tape-recorded and later transcribed and coded to measure accuracy and fluency. Then, the independent samples t-test was employed to analyze the collected data. The results revealed that the experimental group outperformed the control group in accuracy. In contrast, findings substantiated that pushed output had no impact on fluency. The positive impact of pushed output demonstrated in this study is consistent with the hypothesized function of Swain’s (1985 pushed output. The results can provide some useful insights into syllabus design and English language teaching.

Isotopic tracers of sources, wells and of CO{sub 2} reactivity in geological reservoirs; Tracage isotopique des sources, puits et de la reactivite du CO{sub 2} dans les reservoirs geologiques

Energy Technology Data Exchange (ETDEWEB)

Assayag, N

2006-12-15

The aim of this research works consisted in studying the behaviour of the carbonate system (dissolved inorganic carbon: DIC) following a CO{sub 2} injection (artificial or natural), in geological reservoirs. One part of the study consisted in improving an analytical protocol for the measurement of {delta} {sup 13}C DIC and DIC, using a continuous flow mass spectrometer. As a first study, we have focused our attention on the Pavin Lake (Massif Central, France). Owing to its limnologic characteristics (meromictic lake) and a deep volcanic CO{sub 2} contribution, it can be viewed as a natural analogue of reservoir storing important quantities of CO{sub 2} in the bottom part. Isotopic measurements ({delta} {sup 18}O, {delta} {sup 13}C DIC) allowed to better constrain the dynamics of the lake (stratification, seasonal variations), the magnitudes of biological activities (photosynthesis, organic matter decay, methane oxidation, methano-genesis), carbon sources (magmatic, methano-genetic), and the hydrological budgets (sub-lacustrine inputs). The second study was conducted on the Lamont-Doherty test well site (NY, USA). It includes an instrumental borehole which cuts through most of the section of the Palisades sill and into the Newark Basin sediments. Single well push-pull tests were performed: a test solution containing conservative tracers and a reactive tracer (CO{sub 2}) was injected at a permeable depth interval located in basaltic and meta sedimentary rocks. After an incubation period, the test solution/groundwater mixture was extracted from the hydraulically isolated zone. Isotopic measurements ({delta} {sup 18}O, {delta} {sup 13}C DIC) confronted to chemical data (major elements) allowed to investigate the extent of in-situ CO{sub 2}-water-rock interactions: essentially calcite dissolution and at a lesser extend silicate dissolution...and for one of the test, CO{sub 2} degassing. (author)

Push Characteristics in Wheelchair Court Sport Sprinting

NARCIS (Netherlands)

van der Slikke, Rienk M A; Berger, Monique; Bregman, Daan; Veeger, Dirkjan

2016-01-01

Short sprints are important components of most wheelchair court sports, since being faster than the opponent often determines keeping ball possession or not. Sprinting capacity is best measured during a field test, allowing the athlete to freely choose push strategies adapted to their own wheelchair

Push characteristics in wheelchair court sport sprinting

NARCIS (Netherlands)

van der Slikke, R.M.A.; Berger, Monique; Bregman, D.J.J.; Veeger, H.E.J.; van der Helm, FCT; Jansen, AJ

2016-01-01

Short sprints are important components of most wheelchair court sports, since being faster than the opponent often determines keeping ball possession or not. Sprinting capacity is best measured during a field test, allowing the athlete to freely choose push strategies adapted to their own

Effect of push handle height on net moments and forces on the musculoskeletal system during standardized wheelchair pushing tasks

NARCIS (Netherlands)

Van Der Woude, L H; Van Koningsbruggen, C M; Kroes, A L; Kingma, I

1995-01-01

The aim of this investigation was to analyze the external forces and biomechanical loading on the musculoskeletal system during wheelchair pushing, in relation to different push handle heights. In addition, recommendations for wheelchair pushing in accordance with push handle height are made. Eight

Push piece for spent fuel elements magazine

International Nuclear Information System (INIS)

Griveau, R.; Kerlau, D.; Tucoulat, D.; Colas, J.; Pellier, R.

1989-01-01

The push piece permits the displacement of little section elements in a magazine of high section. At the end of cut, the push piece leans its flank against an auxiliary blank holder and the element is pushed by a paddle, the push piece being immobilized [fr

Combined use of ultrasonic liposuction with the pull-through technique for the treatment of gynecomastia.

Science.gov (United States)

Hammond, Dennis C; Arnold, Jame F; Simon, Amy M; Capraro, Philippe A

2003-09-01

The authors present a method of treatment for gynecomastia that combines the use of two techniques of soft-tissue contouring. This method uses ultrasonic liposuction in conjunction with the pull-through technique of direct excision to effectively remove the fibrofatty tissue of the male breast and the fibrous breast bud through a single 1-cm incision. Fifteen patients were treated in this fashion, and each patient demonstrated a smooth, masculine breast contour with a well-concealed scar, which eliminates the stigma of breast surgery. The procedure is technically straightforward and provides consistent results. It is offered as an additional option for the treatment of gynecomastia.

Muscle Activation during Push-Ups with Different Suspension Training Systems

Directory of Open Access Journals (Sweden)

Joaquin Calatayud, Sebastien Borreani, Juan C. Colado, Fernando F Martín, Michael E. Rogers

2014-09-01

Full Text Available The purpose of this study was to analyze upper extremity and core muscle activation when performing push-ups with different suspension devices. Young fit male university students (n = 29 performed 3 push-ups each with 4 different suspension systems. Push-up speed was controlled using a metronome and testing order was randomized. Average amplitude of the electromyographic root mean square of Triceps Brachii, Upper Trapezius, Anterior Deltoid, Clavicular Pectoralis, Rectus Abdominis, Rectus Femoris, and Lumbar Erector Spinae was recorded. Electromyographic signals were normalized to the maximum voluntary isometric contraction (MVIC. Electromyographic data were analyzed with repeated-measures analysis of variance with a Bonferroni post hoc. Based upon global arithmetic mean of all muscles analyzed, the suspended push-up with a pulley system provided the greatest activity (37.76% of MVIC; p < 0.001. Individually, the suspended push-up with a pulley system also provided the greatest triceps brachii, upper trapezius, rectus femoris and erector lumbar spinae muscle activation. In contrast, more stable conditions seem more appropriate for pectoralis major and anterior deltoid muscles. Independent of the type of design, all suspension systems were especially effective training tools for reaching high levels of rectus abdominis activation.

To push or not to push? Affective influences on moral judgment depend on decision frame.

Science.gov (United States)

Pastötter, Bernhard; Gleixner, Sabine; Neuhauser, Theresa; Bäuml, Karl-Heinz T

2013-03-01

People's moods can influence moral judgment. Such influences may arise because moods affect moral emotion, or because moods affect moral thought. The present study provides evidence that, at least in the footbridge dilemma, moods affect moral thought. The results of two experiments are reported in which, after induction of positive, negative, or neutral moods and presentation of the footbridge scenario, participants were asked one of two differentially framed closing questions. In the active frame, participants were asked whether they would be active and push the man, making thoughts about pushing accessible; in the passive frame, they were asked whether they would be passive and not push the man, making thoughts about not pushing accessible. The results show that affective influences on moral judgment depended on participants' decision frame. Compared to neutral moods, positive moods induced utilitarian responding - i.e., deciding to push - in the active decision frame, but induced nonutilitarian responding - i.e., deciding to not push - in the passive decision frame; in negative moods, exactly the opposite picture arose. The results suggest that people's moods affect moral judgment by conferring value on moral thought. Positive moods promote and negative moods inhibit accessible thoughts. Copyright © 2012 Elsevier B.V. All rights reserved.

Analytical Model for Hook Anchor Pull-Out

DEFF Research Database (Denmark)

Brincker, Rune; Ulfkjær, Jens Peder; Adamsen, Peter

1995-01-01

A simple analytical model for the pull-out of a hook anchor is presented. The model is based on a simplified version of the fictitious crack model. It is assumed that the fracture process is the pull-off of a cone shaped concrete part, simplifying the problem by assuming pure rigid body motions...... allowing elastic deformations only in a layer between the pull-out cone and the concrete base. The derived model is in good agreement with experimental results, it predicts size effects and the model parameters found by calibration of the model on experimental data are in good agreement with what should...

Analytical Model for Hook Anchor Pull-out

DEFF Research Database (Denmark)

Brincker, Rune; Ulfkjær, J. P.; Adamsen, P.

A simple analytical model for the pull-out of a hook anchor is presented. The model is based on a simplified version of the fictitious crack model. It is assumed that the fracture process is the pull-off of a cone shaped concrete part, simplifying the problem by assuming pure rigid body motions...... allowing elastic deformations only in a layer between the pull-out cone and the concrete base. The derived model is in good agreement with experimental results, it predicts size effects and the model parameters found by calibration of the model on experimental data are in good agreement with what should...

Hair loss and hair-pulling in rhesus macaques (Macaca mulatta).

Science.gov (United States)

Lutz, Corrine K; Coleman, Kristine; Worlein, Julie; Novak, Melinda A

2013-07-01

Alopecia is a common problem in rhesus macaque colonies. A possible cause of this condition is hair-pulling; however the true relationship between hair-pulling and alopecia is unknown. The purpose of this study was to examine the relationship between hair loss and hair-pulling in 1258 rhesus macaques housed in 4 primate colonies across the United States. Alopecia levels ranged from 34.3% to 86.5% (mean, 49.3%) at the primate facilities. At facilities reporting a sex-associated difference, more female macaques were reported to exhibit alopecia than were males. In contrast, more males were reported to hair-pull. Animals reported to hair-pull were significantly more likely to have some amount of alopecia, but rates of hair-pulling were substantially lower than rates of alopecia, ranging from 0.6% to 20.5% (mean, 7.7%) of the populations. These results further demonstrate that hair-pulling plays only a small role in alopecia in rhesus macaques.

Single-well experimental design for studying residual trapping of superciritcal carbon dioxide

Energy Technology Data Exchange (ETDEWEB)

Zhang, Y.; Freifeld, B.; Finsterle, S.; Leahy, M.; Ennis-King, J.; Paterson, L.; Dance, T.

2010-06-15

The objective of our research is to design a single-well injection-withdrawal test to evaluate residual phase trapping at potential CO{sub 2} geological storage sites. Given the significant depths targeted for CO{sub 2} storage and the resulting high costs associated with drilling to those depths, it is attractive to develop a single-well test that can provide data to assess reservoir properties and reduce uncertainties in the appraisal phase of site investigation. The main challenges in a single-well test design include (1) difficulty in quantifying the amount of CO{sub 2} that has dissolved into brine or migrated away from the borehole; (2) non-uniqueness and uncertainty in the estimate of the residual gas saturation (S{sub gr}) due to correlations among various parameters; and (3) the potential biased S{sub gr} estimate due to unaccounted heterogeneity of the geological medium. To address each of these challenges, we propose (1) to use a physical-based model to simulation test sequence and inverse modeling to analyze data information content and to quantify uncertainty; (2) to jointly use multiple data types generated from different kinds of tests to constrain the Sgr estimate; and (3) to reduce the sensitivity of the designed tests to geological heterogeneity by conducting the same test sequence in both a water-saturated system and a system with residual gas saturation. To perform the design calculation, we build a synthetic model and conduct a formal analysis for sensitivity and uncertain quantification. Both parametric uncertainty and geological uncertainty are considered in the analysis. Results show (1) uncertainty in the estimation of Sgr can be reduced by jointly using multiple data types and repeated tests; and (2) geological uncertainty is essential and needs to be accounted for in the estimation of S{sub gr} and its uncertainty. The proposed methodology is applied to the design of a CO{sub 2} injection test at CO2CRC's Otway Project Site, Victoria

Effect of oil pulling on Streptococcus mutans count in plaque and saliva using Dentocult SM Strip mutans test: A randomized, controlled, triple-blind study

Directory of Open Access Journals (Sweden)

Asokan S

2008-03-01

Full Text Available Background: Oil pulling has been used extensively for many years, without scientific evidence or proof, as a traditional Indian folk remedy to prevent teeth decay, oral malodor, bleeding gums, dryness of throat and cracked lips, and for strengthening the teeth, gums, and jaws. Aims: The aim of this study was to evaluate the effect of oil pulling with sesame oil on the count of Streptococcus mutans in plaque and saliva of children, using the Dentocult SM Strip mutans test, and to compare its efficacy with that of chlorhexidine mouthwash. Materials and Methods: Twenty age-matched adolescent boys were selected based on information obtained through a questionnaire. They were divided randomly into two groups: the control or chlorhexidine group (group I and the study or oil pulling group (group II; there were ten subjects in each group. Plaque and saliva samples were collected from all the 20 subjects on the strips from the Dentocult SM kit and, after incubation, the presence of S. mutans was evaluated using the manufacturers′ chart. The study group practiced oil pulling with sesame oil and the control group used chlorhexidine mouthwash for 10 min every day in the morning before brushing. Samples were collected from both groups after 24 h, 48 h, 1 week, and 2 weeks and the efficacy of oil pulling was compared with that of chlorhexidine mouthwash. Results: There was a reduction in the S. mutans count in the plaque and saliva samples of both the study and the control groups. The reduction in the S. mutans count in the plaque of the study group was statistically significant after 1 and 2 weeks (P = 0.01 and P = 0.008, respectively; the control group showed significant reduction at all the four time points (P = 0.01, P = 0.04, P = 0.005, and P = 0.005, respectively, at 24 h, 48 h, 1 week, and 2 weeks. In the saliva samples, significant reduction in S. mutans count was seen in the control group at 48 h, 1 week, and 2 weeks (P = 0.02, P = 0.02, P = 0

[Methods of pushing at vaginal delivery and pelvi-perineal consequences. Review].

Science.gov (United States)

Ratier, N; Balenbois, E; Letouzey, V; Marès, P; de Tayrac, R

2015-03-01

The main objective of that review was to evaluate the pelvi-perineal consequences of the different methods of pushing at vaginal delivery. A review on PubMed, the Cochrane Library and EM-Premium was performed from 1984 to 2014. Among 29 manuscripts analysed, only nine randomised controlled trials (including one meta-analysis of three trials) comparing Valsalva and spontaneous pushing were selected. A 10 th study, secondary analysis of a randomized controlled trial comparing different methods of perineal protection (warm compresses, massage and manual protection), was also selected. Two trials have shown that spontaneous pushing reduces the risk of perineal tears, but studies were heterogeneous and discordant results do not allowed definitive conclusions. Results on the duration of the second stage of labour are conflicting. The method of pushing does not seem to affect the rate of episiotomy, instrumental delivery and cesarean section. Maternal satisfaction seems to be better after spontaneous pushing. It seems that there is no negative effect of spontaneous pushing on neonate well-being, and one study has shown a significant improvement of prenatal fetal parameters during the expulsive phase. According to current knowledge, both techniques of pushing during the expulsive phase at delivery seem comparable in terms of duration, risk of perineal tears and neonatal outcome. Copyright © 2015 Elsevier Masson SAS. All rights reserved.

Scapular kinematics and muscle activities during pushing tasks.

Science.gov (United States)

Huang, Chun-Kai; Siu, Ka-Chun; Lien, Hen-Yu; Lee, Yun-Ju; Lin, Yang-Hua

2013-01-01

Pushing tasks are functional activities of daily living. However, shoulder complaints exist among workers exposed to regular pushing conditions. It is crucial to investigate the control of shoulder girdles during pushing tasks. The objective of the study was to demonstrate scapular muscle activities and motions on the dominant side during pushing tasks and the relationship between scapular kinematics and muscle activities in different pushing conditions. Thirty healthy adults were recruited to push a four-wheel cart in six pushing conditions. The electromyographic signals of the upper trapezius (UT) and serratus anterior (SA) muscles were recorded. A video-based system was used for measuring the movement of the shoulder girdle and scapular kinematics. Differences in scapular kinematics and muscle activities due to the effects of handle heights and weights of the cart were analyzed using two-way ANOVA with repeated measures. The relationships between scapular kinematics and muscle activities were examined by Pearson's correlation coefficients. The changes in upper trapezius and serratus anterior muscle activities increased significantly with increased pushing weights in the one-step pushing phase. The UT/SA ratio on the dominant side decreases significantly with increased handle heights in the one-step pushing phase. The changes in upward rotation, lateral slide and elevation of the scapula decreased with increased pushing loads in the trunk-forward pushing phase. This study indicated that increased pushing loads result in decreased motions of upward rotation, lateral slide and elevation of the scapula; decreased handle heights result in relatively increased activities of the serratus anterior muscles during pushing tasks.

Effect of different light curing methods on the push-out bond strength of glass fiber post to different root canal regions

Directory of Open Access Journals (Sweden)

Ali Eskandarizadeh

2016-07-01

Full Text Available Background and Aims: Slow polymerization rate in early stage of light curing process leads to higher monomers movement and entering in polymer network that cause higher mechanical properties.The aim of this study was to evaluate the effect of light activation methodes (immediate, 5 and 10 minutes delay on the push-out bond strength of cemented fiber posts in different regions of root canal with two types of resin cements. Materials and Methods: In sixty extracted human single canal, the teeth were decoronated from cement enamel junction and after root canal therapy, FRC postec plus were cemented with two resin cements, Duolink and Variolink 2, in three curing methods; immediate, 5 and 10 minutes of delay. After storing in a dark place for 24 hours, they were cut into three sections: coronal, middle and apical. The push-out bond strength test was performed using a universal testing machine. The failure modes were observed using a stereomicroscope. Data were analyzed using ANOVA and Tukey post hoc test (P0.05. In immediate light curing method, regardless of root region, Duolink had higher push-out bond strength than that of Variolink 2 (P=0.02. In all subgroups, there were reductions in the bond strengths from coronal to apical. Mixed failure at the cement-fiber post interface was predominent in all groups. Conclusion: 5 and 10 minutes delay caused reduction in the push-out bond strength for Variolink 2 but did not have significant effect for Duolink resin cement.

Boris push with spatial stepping

International Nuclear Information System (INIS)

Penn, G; Stoltz, P H; Cary, J R; Wurtele, J

2003-01-01

The Boris push is commonly used in plasma physics simulations because of its speed and stability. It is second-order accurate, requires only one field evaluation per time step, and has good conservation properties. However, for accelerator simulations it is convenient to propagate particles in z down a changing beamline. A 'spatial Boris push' algorithm has been developed which is similar to the Boris push but uses a spatial coordinate as the independent variable, instead of time. This scheme is compared to the fourth-order Runge-Kutta algorithm, for two simplified muon beam lattices: a uniform solenoid field, and a 'FOFO' lattice where the solenoid field varies sinusoidally along the axis. Examination of the canonical angular momentum, which should be conserved in axisymmetric systems, shows that the spatial Boris push improves accuracy over long distances

The usefulness of multi-well aquifer tests in heterogeneous aquifers

International Nuclear Information System (INIS)

Young, S.C.; Benton, D.J.; Herweijer, J.C.; Sims, P.

1990-01-01

Three large-scale (100 m) and seven small-scale (3-7 m) multi-well aquifer tests were conducted in a heterogeneous aquifer to determine the transmissivity distribution across a one-hectare test site. Two of the large-scale tests had constant but different rates of discharge; the remaining large-scale test had a discharge that was pulsed at regulated intervals. The small-scale tests were conducted at two well clusters 20 m apart. The program WELTEST was written to analyze the data. By using the methods of non-linear least squares regression analysis and Broyden's method to solve for non-linear extrema, WELTEST automatically determines the best values of transmissivity and the storage coefficient. The test results show that order of magnitude differences in the calculated transmissivities at a well location can be realized by varying the discharge rate at the pumping well, the duration of the aquifer test, and/or the location of the pumping well. The calculated storage coefficients for the tests cover a five-order magnitude range. The data show a definite trend for the storage coefficient to increase with the distance between the pumping and the observation wells. This trend is shown to be related to the orientation of high hydraulic conductivity zones between the pumping and the observation wells. A comparison among single-well aquifer tests, geological investigations and multi-well aquifer tests indicate that the multi-well tests are poorly suited for characterizing a transmissivity field. (Author) (11 refs., 14 figs.)

A three-dimensional computerized isometric strength measurement system.

Science.gov (United States)

Black, Nancy L; Das, Biman

2007-05-01

The three-dimensional Computerized Isometric Strength Measurement System (CISMS) reliably and accurately measures isometric pull and push strengths in work spaces of paraplegic populations while anticipating comparative studies with other populations. The main elements of the system were: an extendable arm, a vertical supporting track, a rotating platform, a force transducer, stability sensors and a computerized data collection interface. The CISMS with minor modification was successfully used to measure isometric push-up and pull-down strengths of paraplegics and isometric push, pull, push-up and pull-down strength in work spaces for seated and standing able-bodied populations. The instrument has satisfied criteria of versatility, safety and comfort, ease of operation, and durability. Results are accurate within 2N for aligned forces. Costing approximately $1,500 (US) including computer, the system is affordable and accurate for aligned isometric strength measurements.

Interfacial push-out measurements of fully-bonded SiC/SiC composites

International Nuclear Information System (INIS)

Snead, L.L.; Steiner, D.; Zinkle, S.J.

1990-01-01

The direct measurement of interfacial bond strength and frictional resistance to sliding in a fully-bonded SiC/SiC composite is measured. It is shown that a fiber push-out technique can be utilized for small diameter fibers and very thin composite sections. Results are presented for a 22 micron thick section for which 37 out of 44 Nicalon fibers tested were pushed-out within the maximum nanoindentor load of 120 mN. Fiber interfacial yielding, push-out and sliding resistance were measured for each fiber. The distribution of interfacial strengths is treated as being Weibull in form. 14 refs., 5 figs

Pull-Through Capacity in Plywood and OSB

DEFF Research Database (Denmark)

Munch-Andersen, Jørgen; Sørensen, John Dalsgaard

The characteristic pull-through capacity of heads of nails and screws is needed to determine the rope effect for laterally loaded fasteners used to fix sheathing to timberframes. There is no values given in EN 1995 (Eurocode 5) but data for the pull through capacity of nail and screw heads has be...

What Are They Talking About? Analyzing Code Reviews in Pull-Based Development Model

Institute of Scientific and Technical Information of China (English)

Zhi-Xing Li; Yue Yu; Gang Yin; Tao Wang; Huai-Min Wang

2017-01-01

Code reviews in pull-based model are open to community users on GitHub. Various participants are taking part in the review discussions and the review topics are not only about the improvement of code contributions but also about project evolution and social interaction. A comprehensive understanding of the review topics in pull-based model would be useful to better organize the code review process and optimize review tasks such as reviewer recommendation and pull-request prioritization. In this paper, we first conduct a qualitative study on three popular open-source software projects hosted on GitHub and construct a fine-grained two-level taxonomy covering four level-1 categories (code correctness, pull-request decision-making, project management, and social interaction) and 11 level-2 subcategories (e.g., defect detecting, reviewer assigning, contribution encouraging). Second, we conduct preliminary quantitative analysis on a large set of review comments that were labeled by TSHC (a two-stage hybrid classification algorithm), which is able to automatically classify review comments by combining rule-based and machine-learning techniques. Through the quantitative study, we explore the typical review patterns. We find that the three projects present similar comments distribution on each subcategory. Pull-requests submitted by inexperienced contributors tend to contain potential issues even though they have passed the tests. Furthermore, external contributors are more likely to break project conventions in their early contributions.

Giving an insulin injection

Science.gov (United States)

... hand. The bubbles will float to the top. Push the bubbles back into the insulin bottle, then pull back to ... hand. The bubbles will float to the top. Push the bubbles back into the insulin bottle, then pull back to ...

Single crystal fibers growth of double lithium, lanthanium molybdate and adjustment of a micro-pulling down furnace for high vacuum setup; Crescimento de fibras de molibdato duplo de litio e lantanio e adaptacao de sistema de alto vacuo para micro pulling-down

Energy Technology Data Exchange (ETDEWEB)

Silva, Fernando Rodrigues da

2013-07-01

In this work we investigated crystal growth procedures aiming the development of single crystal fiber (SCF) for laser applications. For quality optimization in the fabrication of fluorides SCF a new growth chamber for a micro-pulling down furnace ({mu}-PD) was constructed targeting the fibers fabrication with strict atmosphere control (high vacuum, gas flux and static atmospheres). Simultaneously, the SCF growth process of rare earth double molybdates was studied. The growth of pure and Nd{sup 3+}-doped SCF of LiLa(MoO{sub 4}){sub 2} (LLM) was studied in the range of 0,5 - 10mol% doping. The designed furnace growth chamber with controlled atmosphere was successfully constructed and tested under different conditions. Specially, it was tested with the growth of LiF SFC under CF{sub 4} atmosphere showing the expected results. Transparent and homogeneous SCF of Nd:LLM were grown. In the pure fibers was observed facets formation, however, these defects were minimized after tuning of the growth parameters and additionally with the fibers doping. X-ray analysis showed the crystallization of a single phase (space group I4{sub 1}/a); the optical coherence tomography showed the presence of scattering centers only in regions were some growth stability occurred due to the manual process control. The measured Nd{sup 3+} distribution showed uniform incorporation, indicative of a segregation coefficient close to unity in LLM. The potential laser gain of the system was determined using a numerical solution of the rate equations system for the 805nm, CW pumping regime, showing the maximum laser emission gain at 1.064 {mu}m for a Nd{sup 3+}-doping of 5mol%. (author)

Pulled elbow in infancy: diagnostic role of imaging

International Nuclear Information System (INIS)

Scapinelli, Raffaele; Borgo, Andrea

2005-01-01

Purpose. Pulled elbow is a common injury in infancy. Typically the child, after a sudden pull, refuses to use the arm. The history and clinical findings are sufficient to make the diagnosis, and radiography or ultrasonography are not necessary. When imaging procedures are performed, a few small signs are useful to confirm the diagnosis of pulled elbow. Materials and methods. The authors reviewed the radiographic and ultrasonographic signs reported to be suggestive of pulled elbow (increased radio-condylar distance, increased radio-coronoid distance, proximal radio-ulnar diastasis, deviation of the radio-condylar line) and attempted to confirm their presence in children affected by this trauma. Results. Increased radio-condylar and radio-coronoid distance were present in 8 of 8 cases: proximal radio-ulnar diastasis and deviation of the radio-condylar line were inconsistently present. Ultrasonography gave contradictory results. Conclusions. In typical cases of pulled elbow, radiography or ultrasonography are not necessary for diagnosis and treatment. imaging procedures are recommended only in the case of non typical history, in the presence of deformity or traumatic skin lesions and in children over six years of age. Increased radio-coronoid distance on the affected side is the most frequent and visible sign, which can confirm the diagnosis of pulled elbow. Increased radio-condylar distance is also present, but it is not easy to visualize. Proximal radio-ulnar diastasis and deviation of the radio-condylar line are inconstant. Ultrasonography is difficult to standardize [it

Steady-state Manoeuvring of a Generic ASD Tug in Escort Pull and Bow-rope Aided Push Operation

Directory of Open Access Journals (Sweden)

Jaroslaw Artyszuk

2014-09-01

Full Text Available This paper is devoted to expand the very promising research undertaken in the author's previous work, basically done on simplified modelling the escort push operation. Now, the other two modes of a tug's employment, as stated in the title, are covered. The special focus is again set on the indirect towing in that the towline force is much higher than the thruster force. The ratio of these two forces, referred to as the relative towing force (or amplification ratio is evaluated together with the hull drift angle and the thruster(-s angle for a given escort speed. This mutual relationship is known as the tug performance diagram. Although rather generic (container-type formulas are derived, they are supplied for exemplification purposes with simple, analytically given hull hydrodynamic forces. The aim is also here to provide a basis for further sensitivity analysis of the model and possible improvement/optimisation to the tug design. The obtained charts also could serve as rough and clear guidance for towmasters while escorting.

Effects of Angle Variations in Suspension Push-up Exercise.

Science.gov (United States)

Gulmez, Irfan

2017-04-01

Gulmez, I. Effects of angle variations in suspension push-up exercise. J Strength Cond Res 31(4): 1017-1023, 2017-This study aimed to determine and compare the amount of loads on the TRX Suspension Trainer (TRX) straps and ground reaction forces at 4 different angles during TRX push-ups. Twenty-eight male (mean age, 24.1 ± 2.9 years; height, 179.4 ± 8.0 m; weight, 78.8 ± 9.8 kg) physical education and sports university students participated in this study. The subjects were tested at TRX angles (0, 15, 30, 45°) during the TRX push-ups. Force data were recorded by a force platform and load cells integrated into the TRX straps. The results show that as the TRX angle was reduced, the load applied to the TRX straps increased and simultaneously the load measured by the force platform decreased. This was true for both the elbow joint changing from flexion to extension and vice versa. When the TRX angle was set at 0° and subjects' elbows were at extension during TRX push-up, 50.4% of the subjects' body weight, and when the elbows were at flexion, 75.3% of the body weight was registered by the sensors on the TRX straps. The results of this study can be used in the calculation of the training load and volume (resistance training programming) during TRX push-up exercises at varying angles.

Growth of Yb3+-doped Y2O3 single crystal rods by the micro-pulling-down method

International Nuclear Information System (INIS)

Mun, J.H.; Novoselov, A.; Yoshikawa, A.; Boulon, G.; Fukuda, T.

2005-01-01

The rare-earth sesquioxides (RE 2 O 3 , RE = Lu, Y and Sc) are very promising host crystals for advanced laser diode (LD)-pumped Yb 3+ -doped solid-state lasers due to unusual combination, almost unique of favourable structural, thermal and spectroscopic properties which are described. In spite of these favourable properties, the bulk single crystal growth technology for the rare-earth sesquioxides has not been established yet. The extremely high melting temperature at around 2400 deg. C has prevented it. However, we shall show that yttrium oxide crystals (Yb x Y 1-x ) 2 O 3 , x = 0.0, 0.005, 0.05, 0.08 and 0.15 of cylindrical shape as laser rods with 4.2 mm in diameter and 15-20 mm in length have been grown from rhenium crucibles by the micro-pulling-down method. The crystal quality characterisation of undoped Y 2 O 3 crystal was determined using X-ray rocking curve (XRC) analysis. Yb were homogeneously distributed in Y 2 O 3 host crystal

Volunteer tourists' motivations for choosing homestay in the Kumasi Metropolis of Ghana

Directory of Open Access Journals (Sweden)

Elizabeth Agyeiwaah

2013-01-01

Full Text Available Volunteer tourists’ motivations for choosing homestay accommodation have received little attention from researchers. The objective of this research was to explore the push and pull factors that account for volunteer tourists’ choice of homestay in the Kumasi Metropolis of Ghana. Insights gained from this study will inure better understanding of volunteer tourists’ behaviour to ensure appropriate service delivery by homestay providers. With the help of the "Push and Pull" motivation model by Dann (1977, the findings indicated two main push factors: socio-cultural immersion and economic value; and pull factors: environmental sensitiveness and community service and development. The study found that the most important push and pull factors as perceived by volunteers to Ghana are socio-cultural immersion and environmental sensitiveness. The study confirms the supporting role of homestay for volunteer tourists to Ghana. In the end, the implications of this study are discussed.

Ultrasonic Evaluation of the Pull-Off Adhesion between Added Repair Layer and a Concrete Substrate

Science.gov (United States)

Czarnecki, Slawomir

2017-10-01

This paper concerns the evaluation of the pull-off adhesion between a concrete added repair layer with variable thickness and a concrete substrate, based on parameters assessed using ultrasonic pulse velocity (UPV) method. In construction practice, the experimental determination of pull-off adhesion f b, between added repair layer and a concrete substrate is necessary to assess the quality of repair. This is usually carried out with the use of pull-off method which results in local damage of the added concrete layer in all the testing areas. Bearing this in mind, it is important to describe the method without these disadvantages. The prediction of the pull-off adhesion of the two-layer concrete elements with variable thickness of each layer might be provided by means of UPV method with two-sided access to the investigated element. For this purpose, two-layered cylindrical specimens were obtained by drilling the borehole from a large size specially prepared concrete element. Those two-layer elements were made out of concrete substrate layer and Polymer Cement Concrete (PCC) mortar as an added repair layer. The values of pull-off adhesion f b of the elements were determined before obtaining the samples by using the semi-destructive pull-off method. The ultrasonic wave velocity was determined in samples with variable thickness of each layer and was then compared to theoretical ultrasonic wave velocity predicted for those specimens. The regression curve for the dependence of velocity and pull-off adhesion, determined by the pulloff method, was made. It has been proved that together with an increase of ratio of investigated ultrasonic wave velocity divided by theoretical ultrasonic wave velocity, the pull-off adhesion value f b between added repair layer with variable thickness and a substrate layer also increases.

Electromyographical Comparison of a Traditional, Suspension Device, and Towel Pull-Up

Directory of Open Access Journals (Sweden)

Snarr Ronald L.

2017-08-01

Full Text Available Strengthening muscles of the back may have various implications for improving functions of daily living, aiding in the transfer of power in throwing, and assist in injury prevention of the shoulder complex. While several versions of the pull-up exist, there is currently no literature comparing their differences. The purpose of this investigation was to compare the electromyographical activity of the latissimus dorsi, posterior deltoid, middle trapezius, and biceps brachii while performing three variations of the pull-up. Resistance-trained men and women (n =15, age = 24.87 ± 6.52 years participated in this study by performing traditional pull-ups, suspension device pull-ups, and towel pull-ups in a randomized fashion. Each pull-up was performed for three repetitions with a 1.5 bi-acromial grip-width for each participant. Normalized (%MVC electromyographical values were recorded for each muscle group during each pull-up variation. No significant differences existed within the latissimus dorsi, biceps brachii or posterior deltoid between any of the exercises. For the middle trapezius, towel pull-ups provided significantly lower muscle activity than the traditional pull-up, while no differences between suspension pull-ups and the other variations occurred. In conclusion, only one muscular difference existed between the exercise variations and all versions examined provided electromyographical values, determined by current literature, to invoke a sufficient stimulus to promote increases in muscle strength and hypertrophy. Although further research is needed, practitioners can be confident when programming any of the movement variations examined when attempting to elicit adaptations of muscular strength and hypertrophy.

Interpretation of fracture system geometry using well test data

International Nuclear Information System (INIS)

Doe, T.W.; Geier, J.E.

1990-11-01

This report presents three methods of determining fracture geometry and interconnection from well test information. Method 1 uses evidence for boundary effects in the well test to determine the distance to and type of fracture boundary. Method 2 uses the spatial dimension of the well test to infer the geometry of the fracture-conduit system. Method 3 obtains information of the spacing and transmissivity distribution of individual conductive fractures from fixed-interval-length (FIL) well tests. The three methods are applied to data from the Site Characterization and Validation (SCV) at the 360 m level of the Stripa Mine. The focus of the technology development is the constant-pressure welltest, although the general approaches apply to constant-rate well test, and to a much lesser extent slug or pulse test, which are relatively insensitive to boundaries and spatial dimension. Application of the techniques to the N and W holes in the SCV area shows that there is little evidence for boundary effects in the well test results. There is, on the other hand, considerable variation in the spatial dimension of the well test data ranging from sub-linear (fractures which decrease in conductivity with distance from the hole) to spherical, for three-dimensional fracture systems. The absence of boundary effects suggest that the rock mass in the SCV area contains a well connected fracture system. Major uncertainties in the analysis of well test data limit the use of single borehole measurements. Without assuming the value of specific storage, one can reliably determine only the spatial dimension, and, for two dimensional flow only, the transmissivity. Among the uncertainties are the effective well radius, the degree to which the fracture conduits fill the n-dimensional space in which flow occurs, and the cross-sectional area of the conduits at the wellbore. This report presents a complete development of constant-pressure well test methods for cylindrical flow and flow of arbitrary

Push plate, mounting assembly, circuit board, and method of assembling thereof for ball grid array packages

Science.gov (United States)

Vaughn, Mark R.; Montague, Stephen

2017-05-16

A push plate that includes springs in the form of cantilever flexures and an inspection window is disclosed. The push plate provides a known, uniform, down force and minimal torque to a package to be tested. The cantilevers have a known, calculable down force producing stiffness. The window provides for viewing of the package during testing.

Transport and potential attenuation of nitrogen in shallow groundwaters in the lower Rangitikei catchment, New Zealand.

Science.gov (United States)

Collins, S; Singh, R; Rivas, A; Palmer, A; Horne, D; Manderson, A; Roygard, J; Matthews, A

2017-11-01

Intensive agricultural activities are generally associated with nitrogen leaching from agricultural soils, and this nitrogen has the potential to percolate and contaminate groundwater and surface waters. We assessed surface water and groundwater interactions, and nitrogen leaching and its potential attenuation in shallow groundwater in the lower Rangitikei River catchment (832km 2 ), New Zealand. We combined regional- and local-scale field surveys and experiments, nutrient budget modelling, and hydraulic and geochemical methods, to gain an insight into leaching, transformation and transport of nitrogen via groundwaters to the river in the study area. Concurrent river flow gaugings (in January 2015) and a piezometric map, developed from measured depths to groundwater in 110 bores (in October 2014), suggest groundwater discharges to the Rangitikei River in the upper parts of the study area, while there is groundwater recharge near the coast. The groundwater redox characterisation, based on sampling and analysis of 15 mostly shallow bores (shallow groundwater piezometers (3-6mbgl) using single-well push-pull tests. We found generally low levels (shallow groundwater piezometers (>5mbgl), despite being installed under intensive land uses, such as dairying and cropping. Our in-field push-pull tests showed NO 3 -N reduction at four shallow groundwater piezometers, with the rates of reduction varying from 0.04mgNL -1 h - 1 to 1.57mgNL -1 h - 1 . This highlights the importance of a sound understanding of not only the sources, but also transport and transformation, or fate, of nutrients leached from farms, to mitigate the likely impacts of land use on water quality and ecosystem health in agricultural catchments. Copyright © 2017 Elsevier B.V. All rights reserved.

Characteristics and phenomenology of hair-pulling: an exploration of subtypes.

Science.gov (United States)

du Toit, P L; van Kradenburg, J; Niehaus, D J; Stein, D J

2001-01-01

This study was designed to detail the demographic and phenomenological features of adult chronic hair-pullers. Key possible subtypes were identified a priori. On the basis of the phenomenological data, differences between the following possible subtypes were investigated: hair-pullers with and without DSM-IV trichotillomania (TTM), oral habits, automatic versus focused hair-pulling, positive versus negative affective cues prior to hair-pulling, comorbid self-injurious habits, obsessive-compulsive disorder (OCD), and tics. Forty-seven participants were drawn from an outpatient population of chronic adult hair-pullers. A structured interview that focused on hair-pulling and associated behaviors was administered to participants. Six of the participants (12.8%) were male, and 41 (87.7%) were female. A large number of hair-pullers (63.8%) had comorbid self-injurious habits. A greater proportion of male hair-pullers had comorbid tics when compared with females. Certain subgroups of chronic hair-pullers (e.g., hairpullers with or without automatic/focused hair-pulling, comorbid self-injurious habits, and oral habits) were found to differ on a number of phenomenological and hair-pulling characteristics. However, differences between other possible subgroups (e.g., hair-pullers with or without DSM-IV TTM, comorbid OCD, and negative versus positive affective cues) may reflect greater severity in hair-pulling symptomatology rather than distinct subtypes of chronic hair-pulling. The findings of the present study also indicated that chronic hair-pulling (even in cases where DSM-IV criteria for TTM were not met) has a significant impact on quality of life. The present study provided limited support for the existence of possible subtypes of chronic hair-pulling. Recommendations are made for further investigations into such subtypes. Copyright 2001 by W.B. Saunders Company

Direct push driven in situ color logging tool (CLT): technique, analysis routines, and application

Science.gov (United States)

Werban, U.; Hausmann, J.; Dietrich, P.; Vienken, T.

2014-12-01

Direct push technologies have recently seen a broad development providing several tools for in situ parameterization of unconsolidated sediments. One of these techniques is the measurement of soil colors - a proxy information that reveals to soil/sediment properties. We introduce the direct push driven color logging tool (CLT) for real-time and depth-resolved investigation of soil colors within the visible spectrum. Until now, no routines exist on how to handle high-resolved (mm-scale) soil color data. To develop such a routine, we transform raw data (CIEXYZ) into soil color surrogates of selected color spaces (CIExyY, CIEL*a*b*, CIEL*c*h*, sRGB) and denoise small-scale natural variability by Haar and Daublet4 wavelet transformation, gathering interpretable color logs over depth. However, interpreting color log data as a single application remains challenging. Additional information, such as site-specific knowledge of the geological setting, is required to correlate soil color data to specific layers properties. Hence, we exemplary provide results from a joint interpretation of in situ-obtained soil color data and 'state-of-the-art' direct push based profiling tool data and discuss the benefit of additional data. The developed routine is capable of transferring the provided information obtained as colorimetric data into interpretable color surrogates. Soil color data proved to correlate with small-scale lithological/chemical changes (e.g., grain size, oxidative and reductive conditions), especially when combined with additional direct push vertical high resolution data (e.g., cone penetration testing and soil sampling). Thus, the technique allows enhanced profiling by means of providing another reproducible high-resolution parameter for analysis subsurface conditions. This opens potential new areas of application and new outputs for such data in site investigation. It is our intention to improve color measurements by means method of application and data

Interpretation of Flow Logs from Nevada Test Site Boreholes to Estimate Hydraulic Conductivity Using Numerical Simulations Constrained by Single-Well Aquifer Tests

Science.gov (United States)

Garcia, C. Amanda; Halford, Keith J.; Laczniak, Randell J.

2010-01-01

Hydraulic conductivities of volcanic and carbonate lithologic units at the Nevada Test Site were estimated from flow logs and aquifer-test data. Borehole flow and drawdown were integrated and interpreted using a radial, axisymmetric flow model, AnalyzeHOLE. This integrated approach is used because complex well completions and heterogeneous aquifers and confining units produce vertical flow in the annular space and aquifers adjacent to the wellbore. AnalyzeHOLE simulates vertical flow, in addition to horizontal flow, which accounts for converging flow toward screen ends and diverging flow toward transmissive intervals. Simulated aquifers and confining units uniformly are subdivided by depth into intervals in which the hydraulic conductivity is estimated with the Parameter ESTimation (PEST) software. Between 50 and 150 hydraulic-conductivity parameters were estimated by minimizing weighted differences between simulated and measured flow and drawdown. Transmissivity estimates from single-well or multiple-well aquifer tests were used to constrain estimates of hydraulic conductivity. The distribution of hydraulic conductivity within each lithology had a minimum variance because estimates were constrained with Tikhonov regularization. AnalyzeHOLE simulated hydraulic-conductivity estimates for lithologic units across screened and cased intervals are as much as 100 times less than those estimated using proportional flow-log analyses applied across screened intervals only. Smaller estimates of hydraulic conductivity for individual lithologic units are simulated because sections of the unit behind cased intervals of the wellbore are not assumed to be impermeable, and therefore, can contribute flow to the wellbore. Simulated hydraulic-conductivity estimates vary by more than three orders of magnitude across a lithologic unit, indicating a high degree of heterogeneity in volcanic and carbonate-rock units. The higher water transmitting potential of carbonate-rock units relative

Interpretation of Flow Logs from Nevada Test Site Boreholes to Estimate Hydraulic conductivity Using Numerical Simulations Constrained by Single-Well Aquifer Tests

Energy Technology Data Exchange (ETDEWEB)

Garcia, C. Amanda; Halford, Keith J.; Laczniak, Randell J.

2010-02-12

Hydraulic conductivities of volcanic and carbonate lithologic units at the Nevada Test Site were estimated from flow logs and aquifer-test data. Borehole flow and drawdown were integrated and interpreted using a radial, axisymmetric flow model, AnalyzeHOLE. This integrated approach is used because complex well completions and heterogeneous aquifers and confining units produce vertical flow in the annular space and aquifers adjacent to the wellbore. AnalyzeHOLE simulates vertical flow, in addition to horizontal flow, which accounts for converging flow toward screen ends and diverging flow toward transmissive intervals. Simulated aquifers and confining units uniformly are subdivided by depth into intervals in which the hydraulic conductivity is estimated with the Parameter ESTimation (PEST) software. Between 50 and 150 hydraulic-conductivity parameters were estimated by minimizing weighted differences between simulated and measured flow and drawdown. Transmissivity estimates from single-well or multiple-well aquifer tests were used to constrain estimates of hydraulic conductivity. The distribution of hydraulic conductivity within each lithology had a minimum variance because estimates were constrained with Tikhonov regularization. AnalyzeHOLE simulated hydraulic-conductivity estimates for lithologic units across screened and cased intervals are as much as 100 times less than those estimated using proportional flow-log analyses applied across screened intervals only. Smaller estimates of hydraulic conductivity for individual lithologic units are simulated because sections of the unit behind cased intervals of the wellbore are not assumed to be impermeable, and therefore, can contribute flow to the wellbore. Simulated hydraulic-conductivity estimates vary by more than three orders of magnitude across a lithologic unit, indicating a high degree of heterogeneity in volcanic and carbonate-rock units. The higher water transmitting potential of carbonate-rock units relative

Introduction to nuclear supply chain management. In the context of fuel cycle strategy from LWR cycle system to FR cycle system

International Nuclear Information System (INIS)

Shiotani, Hiroki; Ono, Kiyoshi; Namba, Takashi; Yasumatsu, Naoto; Heta, Masanori

2011-01-01

Supply chain management (SCM) is an important technique to maintain supply and demand balance and to achieve total optimization from upstream to downstream in manufacturers' management. One of the major reasons why SCM receives much attention recently is the trend in production and sales systems from 'Push type' to 'Pull type'. 'Push type' can be restated as 'Make to Stock' (MTS). MTS is a type of supply chain in which the production is not connected to actual demand. On the contrary, 'Pull type' can be restated as 'Make to Order' (MTO) in which the production is connected to actual demand. In this paper, the terminologies and ideas of SCM was introduced into the scenario study to give a fresh perspective for considering LWR cycle to FR cycle transition strategies in Japan. Then, an analytical tool (SCM tool) which has been developed by the authors is used to survey Japanese nuclear energy system in transition with the SCM terminologies and viewpoints. When some of the Japanese nuclear fuel cycle strategies and tools are thought back with the framework of SCM, they tend to treat nuclear fuel cycle system as 'Push type' supply chain in their simulations. For example, a reprocessing plant separates SFs (spent fuels) without considering the actual Pu demand. However, because future reprocessing plants and fuel fabrication plants will act as Pu suppliers (front-end facility) to FR as well as back-end facilities of LWRs, the reasonable plant operation principle can be 'Pull type'. The analysis was conducted by the SCM tool to simulate the behaviors of both MTS and MTO type facilities during the LWR to FR transition period. If there are large uncertainties in the Pu demand or the load factor, etc. of future reprocessing plants, SCM framework is beneficial. Furthermore, the realization of MTO type operation by SCM can reduce the recovered Pu stock in spite of the increase of the SF interim storage. As the result of the investigation on the boundary location of 'Push type

Oblique abdominal muscle activity in response to external perturbations when pushing a cart.

Science.gov (United States)

Lee, Yun-Ju; Hoozemans, Marco J M; van Dieën, Jaap H

2010-05-07

Cyclic activation of the external and internal oblique muscles contributes to twisting moments during normal gait. During pushing while walking, it is not well understood how these muscles respond to presence of predictable (cyclic push-off forces) and unpredictable (external) perturbations that occur in pushing tasks. We hypothesized that the predictable perturbations due to the cyclic push-off forces would be associated with cyclic muscle activity, while external perturbations would be counteracted by cocontraction of the oblique abdominal muscles. Eight healthy male subjects pushed at two target forces and two handle heights in a static condition and while walking without and with external perturbations. For all pushing tasks, the median, the static (10th percentile) and the peak levels (90th percentile) of the electromyographic amplitudes were determined. Linear models with oblique abdominal EMGs and trunk angles as input were fit to the twisting moments, to estimate trunk stiffness. There was no significant difference between the static EMG levels in pushing while walking compared to the peak levels in pushing while standing. When pushing while walking, the additional dynamic activity was associated with the twisting moments, which were actively modulated by the pairs of oblique muscles as in normal gait. The median and static levels of trunk muscle activity and estimated trunk stiffness were significantly higher when perturbations occurred than without perturbations. The increase baseline of muscle activity indicated cocontraction of the antagonistic muscle pairs. Furthermore, this cocontraction resulted in an increased trunk stiffness around the longitudinal axis. Copyright 2010 Elsevier Ltd. All rights reserved.

Power-assisted liposuction and the pull-through technique for the treatment of gynecomastia.

Science.gov (United States)

Lista, Frank; Ahmad, Jamil

2008-03-01

Gynecomastia is a common condition affecting many adolescent and adult males. Surgical techniques utilizing a variety of incisions, excisions, suction-assisted lipectomy, ultrasound-assisted liposuction, power-assisted liposuction, or some combination of these methods have been used in the treatment of gynecomastia. This article describes the authors' method of using power-assisted liposuction and the pull-through technique to treat gynecomastia. This technique involves the use of power-assisted liposuction to remove fatty breast tissue. The pull-through technique is then performed utilizing several instruments to sever the subdermal attachments of fibroglandular breast tissue; this tissue is removed through the incision used for liposuction. Finally, power-assisted liposuction is performed again to contour the remaining breast tissue. A chart review of 99 consecutive patients (197 breasts) treated between January of 2003 and November of 2006 was performed. Ninety-six patients (192 breasts) were successfully treated using this technique. Power-assisted liposuction was performed in all cases, and the average volume aspirated per breast was 459 ml (range, 25 to 1400 ml). Using the pull-through technique, the authors were able to remove between 5 and 70 g of tissue per breast. Complications were minimal (1.0 percent of breasts), and no revisions were required. Since January of 2003, the authors have used this technique to successfully treat 97 percent of their gynecomastia patients. Combining power-assisted liposuction and the pull-through technique has proven to be a versatile approach for the treatment of gynecomastia and consistently produces a naturally contoured male breast while resulting in a single inconspicuous scar.

PEP magnet power supply systems

International Nuclear Information System (INIS)

Jackson, L.T.

1977-01-01

The dc electrical requirements of the PEP magnets fall mainly into two categories: (1) high power and current of single polarity and (2) low-power bi-polar. The first category will be thyristor-chopper controlled off common 600 V dc busses. The second group will utilize continuously controlled push-pull transistor actuators

Interpretation of the lime column penetration test

International Nuclear Information System (INIS)

Liyanapathirana, D S; Kelly, R B

2010-01-01

Dry soil mix (DSM) columns are used to reduce the settlement and to improve the stability of embankments constructed on soft clays. During construction the shear strength of the columns needs to be confirmed for compliance with technical assumptions. A specialized blade shaped penetrometer known as the lime column probe, has been developed for testing DSM columns. This test can be carried out as a pull out resistance test (PORT) or a push in resistance test (PIRT). The test is considered to be more representative of average column shear strength than methods that test only a limited area of the column. Both PORT and PIRT tests require empirical correlations of measured resistance to an absolute measure of shear strength, in a similar manner to the cone penetration test. In this paper, finite element method is used to assess the probe factor, N, for the PORT test. Due to the large soil deformations around the probe, an Arbitrary Lagrangian Eulerian (ALE) based finite element formulation has been used. Variation of N with rigidity index and the friction at the probe-soil interface are investigated to establish a range for the probe factor.

Low pull-in voltage electrostatic MEMS switch using liquid dielectric

KAUST Repository

Zidan, Mohammed A.

2014-08-01

In this paper, we present an electrostatic MEMS switch with liquids as dielectric to reduce the actuation voltage. The concept is verified by simulating a lateral dual gate switch, where the required pull-in voltage is reduced by more than 8 times after using water as a dielectric, to become as low as 5.36V. The proposed switch is simulated using COMSOL multiphysics using various liquid volumes to study their effect on the switching performance. Finally, we propose the usage of the lateral switch as a single switch XOR logic gate.

Incorporating pushing in exclusion-process models of cell migration.

Science.gov (United States)

Yates, Christian A; Parker, Andrew; Baker, Ruth E

2015-05-01

The macroscale movement behavior of a wide range of isolated migrating cells has been well characterized experimentally. Recently, attention has turned to understanding the behavior of cells in crowded environments. In such scenarios it is possible for cells to interact, inducing neighboring cells to move in order to make room for their own movements or progeny. Although the behavior of interacting cells has been modeled extensively through volume-exclusion processes, few models, thus far, have explicitly accounted for the ability of cells to actively displace each other in order to create space for themselves. In this work we consider both on- and off-lattice volume-exclusion position-jump processes in which cells are explicitly allowed to induce movements in their near neighbors in order to create space for themselves to move or proliferate into. We refer to this behavior as pushing. From these simple individual-level representations we derive continuum partial differential equations for the average occupancy of the domain. We find that, for limited amounts of pushing, comparison between the averaged individual-level simulations and the population-level model is nearly as good as in the scenario without pushing. Interestingly, we find that, in the on-lattice case, the diffusion coefficient of the population-level model is increased by pushing, whereas, for the particular off-lattice model that we investigate, the diffusion coefficient is reduced. We conclude, therefore, that it is important to consider carefully the appropriate individual-level model to use when representing complex cell-cell interactions such as pushing.

Two-Man Bobsled Push Start Analysis

Directory of Open Access Journals (Sweden)

Lopes Alexandre Dias

2016-04-01

Full Text Available The importance of push start times on bobsled performance was evidenced by some studies, but at this moment there is no article to the authors’ knowledge that describes the bobsled push start. Thus, the objectives of this study were to describe the two-man bobsled push start, analyze the differences between teams, and estimate the most important variable analyzed. We hypothesized that the pilot and brakeman athletes’ movement patterns during a bobsled pushing start can be described. The images used in this study were obtained during the men’s two-man XIV World Championship of Bobsled (2004. Fifteen best teams participating in the championship were recorded, and four start runs for each team were analyzed. The videos were captured by two digital video cameras. The pilot athletes were analyzed during the moment that they touched the lateral push bar of the sled, and the brakemen were analyzed during the first take-off and first landing. The teams were pooled in three groups of five teams using the final ranking of pushing time. We concluded that there was a distinct pattern movement for pilots and brakemen. The initial position of the majority of the pilots was localized slightly behind the bar. After touching the lateral bar, the pilots remained in a semi-squat position, pushing the sled forward in a pattern of marching movement. All brakemen used the board attached to the track as a support for both feet at the start. The brakeman gave the greatest contribution to break the inertia of the sled. There was no significant difference of movement between the three groups analyzed for the pilot and the brakeman.

Range of Motion of the Ankle According to Pushing Force, Gender and Knee Position.

Science.gov (United States)

Cho, Kang Hee; Jeon, Yumi; Lee, Hyunkeun

2016-04-01

To investigate the difference of range of motion (ROM) of ankle according to pushing force, gender and knee position. One hundred and twenty-eight healthy adults (55 men, 73 women) between the ages of 20 and 51, were included in the study. One examiner measured the passive range of motion (PROM) of ankle by Dualer IQ Inclinometers and Commander Muscle Testing. ROM of ankle dorsiflexion (DF) and plantarflexion (PF) according to change of pushing force and knee position were measured at prone position. There was significant correlation between ROM and pushing force, the more pushing force leads the more ROM at ankle DF and ankle PF. Knee flexion of 90° position showed low PF angle and high ankle DF angle, as compared to the at neutral position of knee joint. ROM of ankle DF for female was greater than for male, with no significant difference. ROM of ankle PF for female was greater than male regardless of the pushing force. To our knowledge, this is the first study to assess the relationship between pushing force and ROM of ankle joint. There was significant correlation between ROM of ankle and pushing force. ROM of ankle PF for female estimated greater than male regardless of the pushing force and the number of measurement. The ROM of the ankle is measured differently according to the knee joint position. Pushing force, gender and knee joint position are required to be considered when measuring the ROM of ankle joint.

Operant Conditioning in Honey Bees (Apis mellifera L.): The Cap Pushing Response.

Science.gov (United States)

Abramson, Charles I; Dinges, Christopher W; Wells, Harrington

2016-01-01

The honey bee has been an important model organism for studying learning and memory. More recently, the honey bee has become a valuable model to understand perception and cognition. However, the techniques used to explore psychological phenomena in honey bees have been limited to only a few primary methodologies such as the proboscis extension reflex, sting extension reflex, and free flying target discrimination-tasks. Methods to explore operant conditioning in bees and other invertebrates are not as varied as with vertebrates. This may be due to the availability of a suitable response requirement. In this manuscript we offer a new method to explore operant conditioning in honey bees: the cap pushing response (CPR). We used the CPR to test for difference in learning curves between novel auto-shaping and more traditional explicit-shaping. The CPR protocol requires bees to exhibit a novel behavior by pushing a cap to uncover a food source. Using the CPR protocol we tested the effects of both explicit-shaping and auto-shaping techniques on operant conditioning. The goodness of fit and lack of fit of these data to the Rescorla-Wagner learning-curve model, widely used in classical conditioning studies, was tested. The model fit well to both control and explicit-shaping results, but only for a limited number of trials. Learning ceased rather than continuing to asymptotically approach the physiological most accurate possible. Rate of learning differed between shaped and control bee treatments. Learning rate was about 3 times faster for shaped bees, but for all measures of proficiency control and shaped bees reached the same level. Auto-shaped bees showed one-trial learning rather than the asymptotic approach to a maximal efficiency. However, in terms of return-time, the auto-shaped bees' learning did not carry over to the covered-well test treatments.

A General Semi-Analytical Solution for Three Types of Well Tests in Confined Aquifers with a Partially Penetrating Well

Directory of Open Access Journals (Sweden)

Shaw-Yang Yang Hund-Der Yeh

2012-01-01

Full Text Available This note develops a general mathematical model for describing the transient hydraulic head response for constant-head test, constant-flux test, and slug test in a radial confined aquifer system with a partially penetrating well. The Laplace-domain solution for the model is derived by applying the Laplace transform with respect to time and finite Fourier cosine transform with respect to the z-direction. This new solution has been shown to reduce to the constant-head test when discounting the wellbore storage and maintaining a constant well water level. This solution can also be reduced to the constant-flux test solution when discounting the wellbore storage and keeping a constant pumping rate in the well. Moreover, the solution becomes the slug test solution when there is no pumping in the well. This general solution can be used to develop a single computer code to estimate aquifer parameters if coupled with an optimization algorithm or to assess the effect of well partial penetration on hydraulic head distribution for three types of aquifer tests.

Pull remanufacturing: A case study

Energy Technology Data Exchange (ETDEWEB)

Levine, L.O.

1992-09-01

This paper describes how pull production methods have been applied to a manual transmission remanufacturing line at Tooele Army Depot in Utah. The paper emphasizes techniques for linking the control of disassembly and cleaning operations to the repair and assembly portions of the production system (PP&C). The primary objective is to show that production planning and control can be simplified when pull mechanisms are combined with shop floor improvements. One approach to applying MRP II to remanufacturing is to use a separate production schedule for the disassembly and assembly portions of the operation. This approach is primarily needed when managing the delivery and inventory of cores is critical to the successful operation of a remanufacturing organization. Because Army depots frequently have an adequate inventory of cores on hand (somewhere on-site), this requirement is usually less significant. Therefore, it is possible to eliminate the use of a master production schedule for disassembly and rely on pull linkages from the repair and assembly operations to control the activity of the disassembly and cleaning operations. In remanufacturing environments having multiple products and adequate buffers of core inventory, effective coordination of disassembly and cleaning functions with assembly production requirements becomes a key production control issue.

Pull remanufacturing: A case study

Energy Technology Data Exchange (ETDEWEB)

Levine, L.O.

1992-09-01

This paper describes how pull production methods have been applied to a manual transmission remanufacturing line at Tooele Army Depot in Utah. The paper emphasizes techniques for linking the control of disassembly and cleaning operations to the repair and assembly portions of the production system (PP C). The primary objective is to show that production planning and control can be simplified when pull mechanisms are combined with shop floor improvements. One approach to applying MRP II to remanufacturing is to use a separate production schedule for the disassembly and assembly portions of the operation. This approach is primarily needed when managing the delivery and inventory of cores is critical to the successful operation of a remanufacturing organization. Because Army depots frequently have an adequate inventory of cores on hand (somewhere on-site), this requirement is usually less significant. Therefore, it is possible to eliminate the use of a master production schedule for disassembly and rely on pull linkages from the repair and assembly operations to control the activity of the disassembly and cleaning operations. In remanufacturing environments having multiple products and adequate buffers of core inventory, effective coordination of disassembly and cleaning functions with assembly production requirements becomes a key production control issue.

'Mister Badger' Pushing Mars Rock

Science.gov (United States)

1976-01-01

Viking's soil sampler collector arm successfully pushed a rock on the surface of Mars during the afternoon of Friday, October 8. The irregular-shaped rock was pushed several inches by the Lander's collector arm, which displaced the rock to the left of its original position, leaving it cocked slightly upward. Photographs and other information verified the successful rock push. Photo at left shows the soil sampler's collector head pushing against the rock, named 'Mister Badger' by flight controllers. Photo at right shows the displaced rock and the depression whence it came. Part of the soil displacement was caused by the collector s backhoe. A soil sample will be taken from the site Monday night, October 11. It will then be delivered to Viking s organic chemistry instrument for a series of analyses during the next few weeks. The sample is being sought from beneath a rock because scientists believe that, if there are life forms on Mars, they may seek rocks as shelter from the Sun s intense ultraviolet radiation.

Effect of honeybee stinger and its microstructured barbs on insertion and pull force.

Science.gov (United States)

Ling, Jintian; Song, Zhenhua; Wang, Jiarui; Chen, Keyun; Li, Jiyu; Xu, Shujia; Ren, Lei; Chen, Zhipeng; Jin, Dianwen; Jiang, Lelun

2017-04-01

Worker honeybee is well-known for its stinger with microscopic backward-facing barbs for self-defense. The natural geometry of the stinger enables painless penetration and adhesion in the human skin to deliver poison. In this study, Apis cerana worker honeybee stinger and acupuncture microneedle (as a barbless stinger) were characterized by Scanning Electron Microscope (SEM). The insertion and pull process of honeybee stinger into rabbit skin was performed by a self-developed mechanical loading equipment in comparison with acupuncture needle. In order to better understand the insertion and pull mechanisms of the stinger and its barbs in human multilayer skin, a nonlinear finite element method (FEM) was conducted. Experimental results showed that the average pull-out force of the stinger was 113.50mN and the average penetration force was only 5.75mN. The average penetration force of the stinger was about one order of magnitude smaller than that of an acupuncture microneedle while the average pull-out force was about 70 times larger than that of an acupuncture microneedle. FEM results showed that the stress concentrations were around the stinger tip and its barbs during the insertion process. The barbs were jammed in and torn the skin during the pull process. The insertion force of the stinger was greatly minimized due to its ultrasharp stinger tip and barbs while the pull force was seriously enhanced due to the mechanical interlocking of the barbs in the skin. These excellent properties are mainly a result of optimal geometry evolved by nature. Such finding may provide an inspiration for the further design of improved tissue adhesives and micro-needles for painless transdermal drug delivery and bio-signal recording. Copyright © 2017 Elsevier Ltd. All rights reserved.

Fixing Affordability: An Approach for Advancing Federalism in the Modern Era. State-Federal Partnerships in Postsecondary Education

Science.gov (United States)

Cooper, Michelle Asha

2016-01-01

There is a constant push and pull between state and the federal governments to find the right balance of federalism. By applying this "push-pull" framework to higher education, this brief looks at past policy interventions and how this framework can help to understand the free college movement.

Selectively Encrypted Pull-Up Based Watermarking of Biometric data

Science.gov (United States)

Shinde, S. A.; Patel, Kushal S.

2012-10-01

Biometric authentication systems are becoming increasingly popular due to their potential usage in information security. However, digital biometric data (e.g. thumb impression) are themselves vulnerable to security attacks. There are various methods are available to secure biometric data. In biometric watermarking the data are embedded in an image container and are only retrieved if the secrete key is available. This container image is encrypted to have more security against the attack. As wireless devices are equipped with battery as their power supply, they have limited computational capabilities; therefore to reduce energy consumption we use the method of selective encryption of container image. The bit pull-up-based biometric watermarking scheme is based on amplitude modulation and bit priority which reduces the retrieval error rate to great extent. By using selective Encryption mechanism we expect more efficiency in time at the time of encryption as well as decryption. Significant reduction in error rate is expected to be achieved by the bit pull-up method.

Prosthetic ankle push-off work reduces metabolic rate but not collision work in non-amputee walking

OpenAIRE

Caputo, Joshua M.; Collins, Steven H.

2014-01-01

Individuals with unilateral below-knee amputation expend more energy than non-amputees during walking and exhibit reduced push-off work and increased hip work in the affected limb. Simple dynamic models of walking suggest a possible solution, predicting that increasing prosthetic ankle push-off should decrease leading limb collision, thereby reducing overall energy requirements. We conducted a rigorous experimental test of this idea wherein ankle-foot prosthesis push-off work was incrementall...

Strategies of Production Control as Tools of Efficient Management of Production Enterprises

Science.gov (United States)

Budynek, Mateusz; Celińska, Elżbieta; Dybikowska, Adrianna; Kozak, Monika; Ratajczak, Joanna; Urban, Jagoda; Materne, Karolina

2016-03-01

The paper discusses the problem of principle methods of production control as a strategy supporting the production system and stimulating efficient solutions in respect management in production enterprises. The article describes MRP, ERP, JIT, KANBAN and TOC methods and focuses on their main goals, principles of functioning as well as benefits resulting from their application. The methods represent two diverse strategies of production control, i.e. pull and push strategies. Push strategies are used when the plans apply to the first and principle part of production and are based on the demand forecasts. Pull strategies are used when all planning decisions apply to the final stage and depend on the actual demand or orders from customers.

Field evaluation of a direct push deployed sensor probe for vertical soil water content profiling

Science.gov (United States)

Vienken, Thomas; Reboulet, Ed; Leven, Carsten; Kreck, Manuel; Zschornack, Ludwig; Dietrich, Peter

2015-04-01

Reliable high-resolution information about vertical variations in soil water content, i.e. total porosity in the saturated zone, is essential for flow and transport predictions within the subsurface. However, porosity measurements are often associated with high efforts and high uncertainties, e.g. caused by soil disturbance during sampling or sensor installation procedures. In hydrogeological practice, commonly applied tools for the investigation of vertical soil water content distribution include gravimetric laboratory analyses of soil samples and neutron probe measurements. A yet less well established technique is the use of direct push-deployed sensor probes. Each of these methods is associated with inherent advantages and limitations due to their underlying measurement principles and operation modes. The presented study describes results of a joint field evaluation of the individual methods under different depositional and hydrogeological conditions with special focus on the performance on the direct push-deployed water content profiler. Therefore, direct push-profiling results from three different test sites are compared with results obtained from gravimetric analysis of soil cores and neutron probe measurements. In direct comparison, the applied direct push-based sensor probe proved to be a suitable alternative for vertical soil water content profiling to neutron probe technology, and, in addition, proved to be advantageous over gravimetric analysis in terms vertical resolution and time efficiency. Results of this study identify application-specific limitations of the methods and thereby highlight the need for careful data evaluation, even though neutron probe measurements and gravimetric analyses of soil samples are well established techniques (see Vienken et al. 2013). Reference: Vienken, T., Reboulet, E., Leven, C., Kreck, M., Zschornack, L., Dietrich, P., 2013. Field comparison of selected methods for vertical soil water content profiling. Journal of

Lifetime of Manet steel in load-cycling tests in vacuum at 20 and 550deg C

International Nuclear Information System (INIS)

Ullmaier, H.; Schmitz, W.

1989-01-01

Fatigue tests in vacuum were carried out on the Manet heat of DIN 1.4914 martensitic steel (X13Cr10.7Ni0.85Mo0.75V0.22) in push-pull type, stress-controlled experiments at room temperature and 823 K. The fatigue life was determined as a function of stress amplitude, mean stress, frequency and hold time. At 823 K creep has a strong influence on the life time, particularly at low frequencies and long hold times in tension. The results are phenomenologically described by a simple linear damage summation approach. Even at room temperature the life time of specimens tested in vacuum is about an order of magnitude higher than of those tested in air. This stresses the importance of providing the correct test environment in collecting fatigue data for the design of fusion devices. (orig./MM)

A single well pumping and recovery test to measure in situ acrotelm transmissivity in raised bogs

NARCIS (Netherlands)

Schaaf, van der S.

2004-01-01

A quasi-steady-state single pit pumping and recovery test to measure in situ the transmissivity of the highly permeable upper layer of raised bogs, the acrotelm, is described and discussed. The basic concept is the expanding depression cone during both pumping and recovery. It is shown that applying

Initial atomic coherences and Ramsey frequency pulling in fountain clocks

Science.gov (United States)

Gerginov, Vladislav; Nemitz, Nils; Weyers, Stefan

2014-09-01

In the uncertainty budget of primary atomic cesium fountain clocks, evaluations of frequency-pulling shifts of the hyperfine clock transition caused by unintentional excitation of its nearby transitions (Rabi and Ramsey pulling) have been based so far on an approach developed for cesium beam clocks. We re-evaluate this type of frequency pulling in fountain clocks and pay particular attention to the effect of initial coherent atomic states. We find significantly enhanced frequency shifts caused by Ramsey pulling due to sublevel population imbalance and corresponding coherences within the state-selected hyperfine component of the initial atom ground state. Such shifts are experimentally investigated in an atomic fountain clock and quantitative agreement with the predictions of the model is demonstrated.

Modeling and Simulation of Two Wheelchair Accessories for Pushing Doors.

Science.gov (United States)

Abdullah, Soran Jalal; Shaikh Mohammed, Javeed

2017-03-27

Independent mobility is vital to individuals of all ages, and wheelchairs have proven to be great personal mobility devices. The tasks of opening and navigating through a door are trivial for healthy people, while the same tasks could be difficult for some wheelchair users. A wide range of intelligent wheelchair controllers and systems, robotic arms, or manipulator attachments integrated with wheelchairs have been developed for various applications, including manipulating door knobs. Unfortunately, the intelligent wheelchairs and robotic attachments are not widely available as commercial products. Therefore, the current manuscript presents the modeling and simulation of a novel but simple technology in the form of a passive wheelchair accessory (straight, arm-like with a single wheel, and arc-shaped with multiple wheels) for pushing doors open from a wheelchair. From the simulations using different wheel shapes and sizes, it was found that the arc-shaped accessory could push open the doors faster and with almost half the required force as compared to the arm-like accessory. Also, smaller spherical wheels were found to be best in terms of reaction forces on the wheels. Prototypes based on the arc-shaped accessory design will be manufactured and evaluated for pushing doors open and dodging or gliding other obstacles.

Targeted Drug Delivery in the Suprachoroidal Space by Swollen Hydrogel Pushing

Science.gov (United States)

Jung, Jae Hwan; Desit, Patcharin; Prausnitz, Mark R.

2018-01-01

Purpose The purpose is to target model drug particles to the posterior region of the suprachoroidal space (SCS) of the eye controlled via pushing by hydrogel swelling. Methods A particle formulation containing 1% hyaluronic acid (HA) with fluorescent polymer particles and a hydrogel formulation containing 4% HA were introduced in a single syringe as two layers without mixing, and injected sequentially into the SCS of the rabbit eye ex vivo and in vivo using a microneedle. Distribution of particles in the eye was determined by microscopy. Results During injection, the particle formulation was pushed toward the middle of the SCS by the viscous hydrogel formulation, but less than 12% of particles reached the posterior SCS. After injection, the particle formulation was pushed further toward the macula and optic nerve in the posterior SCS by hydrogel swelling and spreading. Heating the eye to 37°C, or injecting in vivo decreased viscosity and mechanical strength of the hydrogel, thereby allowing it to swell and flow further in the SCS. A high salt concentration (9% NaCl) in the hydrogel formulation further increased hydrogel swelling due to osmotic flow into the hydrogel. In this way, up to 76% of particles were delivered to the posterior SCS from an injection made near the limbus. Conclusions This study shows that model drug particles can be targeted to the posterior SCS by HA hydrogel swelling and pushing without particle functionalization or administering external driving forces. PMID:29677369

Targeted Drug Delivery in the Suprachoroidal Space by Swollen Hydrogel Pushing.

Science.gov (United States)

Jung, Jae Hwan; Desit, Patcharin; Prausnitz, Mark R

2018-04-01

The purpose is to target model drug particles to the posterior region of the suprachoroidal space (SCS) of the eye controlled via pushing by hydrogel swelling. A particle formulation containing 1% hyaluronic acid (HA) with fluorescent polymer particles and a hydrogel formulation containing 4% HA were introduced in a single syringe as two layers without mixing, and injected sequentially into the SCS of the rabbit eye ex vivo and in vivo using a microneedle. Distribution of particles in the eye was determined by microscopy. During injection, the particle formulation was pushed toward the middle of the SCS by the viscous hydrogel formulation, but less than 12% of particles reached the posterior SCS. After injection, the particle formulation was pushed further toward the macula and optic nerve in the posterior SCS by hydrogel swelling and spreading. Heating the eye to 37°C, or injecting in vivo decreased viscosity and mechanical strength of the hydrogel, thereby allowing it to swell and flow further in the SCS. A high salt concentration (9% NaCl) in the hydrogel formulation further increased hydrogel swelling due to osmotic flow into the hydrogel. In this way, up to 76% of particles were delivered to the posterior SCS from an injection made near the limbus. This study shows that model drug particles can be targeted to the posterior SCS by HA hydrogel swelling and pushing without particle functionalization or administering external driving forces.

Integrated Framework for Assessing Impacts of CO₂ Leakage on Groundwater Quality and Monitoring-Network Efficiency: Case Study at a CO₂ Enhanced Oil Recovery Site.

Science.gov (United States)

Yang, Changbing; Hovorka, Susan D; Treviño, Ramón H; Delgado-Alonso, Jesus

2015-07-21

This study presents a combined use of site characterization, laboratory experiments, single-well push-pull tests (PPTs), and reactive transport modeling to assess potential impacts of CO2 leakage on groundwater quality and leakage-detection ability of a groundwater monitoring network (GMN) in a potable aquifer at a CO2 enhanced oil recovery (CO2 EOR) site. Site characterization indicates that failures of plugged and abandoned wells are possible CO2 leakage pathways. Groundwater chemistry in the shallow aquifer is dominated mainly by silicate mineral weathering, and no CO2 leakage signals have been detected in the shallow aquifer. Results of the laboratory experiments and the field test show no obvious damage to groundwater chemistry should CO2 leakage occur and further were confirmed with a regional-scale reactive transport model (RSRTM) that was built upon the batch experiments and validated with the single-well PPT. Results of the RSRTM indicate that dissolved CO2 as an indicator for CO2 leakage detection works better than dissolved inorganic carbon, pH, and alkalinity at the CO2 EOR site. The detection ability of a GMN was assessed with monitoring efficiency, depending on various factors, including the natural hydraulic gradient, the leakage rate, the number of monitoring wells, the aquifer heterogeneity, and the time for a CO2 plume traveling to the monitoring well.