Acetate self-mixing and direct thermal reaction for preparation of LiCoO2

International Nuclear Information System (INIS)

Jung, Bum-Young; Kang, Hyun-Koo; Jeong, In-Seong; Han, Kyoo-Seung; Lee, Youngil; Choo, Jaebum; Ryu, Kwang Sun

2004-01-01

Layered LiCoO 2 as a cathode material for rechargeable lithium battery is prepared using the acetate self-mixing method. Using this method, the preparation procedure consists of just two steps: spontaneous and homogeneous mixing of molten acetates at 80 deg. C, as well as direct thermal reaction at high temperature without any pulverization, grinding, agglomeration, particle morphology controlling, particle size controlling, and even artificial stirring of reactants. When lithium and cobalt acetates are exposed to the temperature of 80 deg. C, they can be fluidized substances by themselves without any solvents and spontaneously mixed together. In this way, layered LiCoO 2 phase is prepared by just simple heat treatment. The heating at 350 deg. C is interposed to accomplish steady intermediate phase translation without any intermittent cooling. The 7 Li MAS NMR and Raman spectra upon the thermal exposure of the reactants demonstrate the feature of the spontaneous mixing process of the molten reactants. The LiCoO 2 prepared by the acetate self-mixing method show quite prospective properties as a cathode material for lithium rechargeable battery, an initial discharge capacity of 149.5 mAh/g and the discharge capacity retention of 98.9% and 97.5% after 10 and 20 cycles, respectively

Influence of the Mixing Ways of Reactants on ZnO Morphology

Directory of Open Access Journals (Sweden)

Lining Yang

2013-01-01

Full Text Available ZnO particles with various morphologies were synthesized by mixing ZnSO4 and NaOH solutions at 25°C followed by aging of the suspensions at 40–80°C for 2.0 h, keeping the initial molar ratio of Zn2+ to OH− at 1 : 4. ZnO irregular plates were prepared by adding NaOH to ZnSO4 while ε-Zn(OH2 rhombic particles were produced using the opposite mixing way. After aging of the slurries at 80°C for 2.0 h, the ZnO plates were kept stable while the ε-Zn(OH2 rhombic particles were converted to ZnO whiskers with a length of 1.0–4.0 μm and a diameter of 0.03–0.3 μm. Thermodynamic analysis indicated that the formation of the Zn-bearing precipitates (ZnO or ε-Zn(OH2 at room temperature was connected closely with the solution composition.

Single Vs Mixed Organic Cation for Low Temperature Processed Perovskite Solar Cells

International Nuclear Information System (INIS)

Mahmud, Md Arafat; Elumalai, Naveen Kumar; Upama, Mushfika Baishakhi; Wang, Dian; Wright, Matthew; Chan, Kah Howe; Xu, Cheng; Haque, Faiazul; Uddin, Ashraf

2016-01-01

Highlights: • Low temperature processed ZnO based single & mixed organic cation perovskite device. • 37% higher PCE in mixed cation perovskite solar cells (PSCs) than single cation ones. • Mixed cation PSCs exhibit significantly reduced photocurrent hysteresis. • Mixed cation PSCs demonstrate three fold higher device stability than single cation PSCs. • Electronic properties are analyzed using Electrochemical Impedance Spectroscopy. - Abstract: The present work reports a comparative study between single and mixed organic cation based MAPbI 3 and MA 0.6 FA 0.4 PbI 3 perovskite devices fabricated in conjunction with low temperature processed (<150 °C) ZnO electron transport layers. MA 0.6 FA 0.4 PbI 3 perovskite devices demonstrate 37% higher power conversion efficiency compared to MAPbI 3 perovskite devices developed on the ZnO ETL. In addition, MA 0.6 FA 0.4 PbI 3 devices exhibit very low photocurrent hysteresis and they are three-fold more stable than conventional MAPbI 3 PSCs (perovskite solar cells). An in-depth analysis on the charge transport properties in both fresh and aged devices has been carried out using electrochemical impedance spectroscopy analysis to comprehend the enhanced device stability of the mixed perovskite devices developed on the ZnO ETL. The study also investigates into the interfacial charge transfer characteristics associated with the ZnO/mixed organic cation perovskite interface and concomitant influence on the inherent electronic properties.

Low temperature synthesis of Mo2C/W2C superlattices via ultra-thin modulated reactants

International Nuclear Information System (INIS)

Johnson, C.D.; Johnson, D.C.

1996-01-01

The authors report here a synthesis method of preparing carbide superlattices using ultra-thin modulated reactants. Initial investigations into the synthesis of the binary systems, Mo 2 C and W 2 C using ultra-thin modulated reactants revealed that both can be formed at relatively low temperatures (500 and 600 C respectively). DSC and XRD data suggested a two step reaction pathway involving interdiffusion of the initial modulated reactant followed by crystallization of the final product, if the modulation length is on the order of 10 angstrom. This information was used to form Mo 2 C/W 2 C superlattices using the structure of the ultra-thin modulated reactant to control the final superlattice period. Relatively large superlattice modulations were kinetically trapped by having several repeat units of each binary within the total repeat of the initial reactant. DSC and XRD data again are consistent with a two step reaction pathway leading to the formation of carbide superlattices

Single-event effects in analog and mixed-signal integrated circuits

International Nuclear Information System (INIS)

Turflinger, T.L.

1996-01-01

Analog and mixed-signal integrated circuits are also susceptible to single-event effects, but they have rarely been tested. Analog circuit single-particle transients require modified test techniques and data analysis. Existing work is reviewed and future concerns are outlined

Age-dependent mixing of deep-sea sediments

International Nuclear Information System (INIS)

Smith, C.R.; Maggaard, L.; Pope, R.H.; DeMaster, D.J.

1993-01-01

Rates of bioturbation measured in deep-sea sediments commonly are tracer dependent; in particular, shorter lived radiotracers (such as 234 Th) often yield markedly higher diffusive mixing coefficients than their longer-lived counterparts (e.g., 210 Pb). At a single station in the 1,240-m deep Santa Catalina Basin, the authors document a strong negative correlation between bioturbation rate and tracer half-life. Sediment profiles of 234 Th (half-life = 24 days) yield an average mixing coefficient (60 cm 2 y -1 ) two orders of magnitude greater than that for 210 Pb (half-life = 22 y, mean mixing coefficient = 0.4 cm 2 y -1 ). A similar negative relationship between mixing rate and tracer time scale is observed at thirteen other deep-sea sites in which multiple radiotracers have been used to assess diffusive mixing rates. This relationship holds across a variety of radiotracer types and time scales. The authors hypothesize that this negative relationship results from age-dependent mixing, a process in which recently sedimented, food-rich particles are ingested and mixed at higher rates by deposit feeders than are older, food-poor particles. Results from an age-dependent mixing model demonstrate that this process indeed can yield the bioturbation-rate vs. tracer-time-scale correlations observed in deep-sea sediments. Field data on mixing rates of recently sedimented particles, as well as the radiotracer activity of deep-sea deposit feeders, provide strong support for the age-dependent mixing model. The presence of age-dependent mixing in deep-sea sediments may have major implications for diagenetic modeling, requiring a match between the characteristic time scales of mixing tracers and modeled reactants. 102 refs., 6 figs., 5 tabs

Synthesis of new thermoelectrics using modulated elemental reactants

Energy Technology Data Exchange (ETDEWEB)

Hornbostel, M D; Sellinschegg, H; Johnson, D C

1997-07-01

A series of new, metastable ternary crystalline compounds with the skutterudite crystal structure have been synthesized using modulated elemental reactants. The initial reactants are made up of multiple repeats of a {approximately}25 {angstrom} thick unit containing elemental layers of the desired ternary metal, iron and antimony. Low temperature annealing (150 C) results in interdiffusion of the elemental layers to form amorphous reaction intermediates. Annealing these intermediates at temperatures between 200 C and 250 C results in exothermic crystallization of the desired skutterudite crystal structure. Most of the new compounds prepared are only kinetically stable, decomposing exothermically to form thermodynamically more stable mixtures of binary compounds and elements. Low angle x-ray diffraction studies show that the resulting films are exceedingly smooth. These films have an ideal geometry for measuring properties of importance for thermoelectric devices--the Seebeck coefficient and the electrical conductivity. Thermal conductivity can be measured using a modification of the 3{omega} technique of Cahill. Samples can be produced rapidly, allowing for systematic screening and subsequent optimization as a function of composition and doping levels.

Detailed high-resolution three-dimensional simulations of OMEGA separated reactants inertial confinement fusion experiments

Energy Technology Data Exchange (ETDEWEB)

Haines, Brian M., E-mail: bmhaines@lanl.gov; Fincke, James R.; Shah, Rahul C.; Boswell, Melissa; Fowler, Malcolm M.; Gore, Robert A.; Hayes-Sterbenz, Anna C.; Jungman, Gerard; Klein, Andreas; Rundberg, Robert S.; Steinkamp, Michael J.; Wilhelmy, Jerry B. [Los Alamos National Laboratory, MS T087, Los Alamos, New Mexico 87545 (United States); Grim, Gary P. [Lawrence Livermore National Laboratory, Livermore, California 94550 (United States); Forrest, Chad J.; Silverstein, Kevin; Marshall, Frederic J. [Laboratory for Laser Energetics, University of Rochester, Rochester, New York 14623 (United States)

2016-07-15

We present results from the comparison of high-resolution three-dimensional (3D) simulations with data from the implosions of inertial confinement fusion capsules with separated reactants performed on the OMEGA laser facility. Each capsule, referred to as a “CD Mixcap,” is filled with tritium and has a polystyrene (CH) shell with a deuterated polystyrene (CD) layer whose burial depth is varied. In these implosions, fusion reactions between deuterium and tritium ions can occur only in the presence of atomic mix between the gas fill and shell material. The simulations feature accurate models for all known experimental asymmetries and do not employ any adjustable parameters to improve agreement with experimental data. Simulations are performed with the RAGE radiation-hydrodynamics code using an Implicit Large Eddy Simulation (ILES) strategy for the hydrodynamics. We obtain good agreement with the experimental data, including the DT/TT neutron yield ratios used to diagnose mix, for all burial depths of the deuterated shell layer. Additionally, simulations demonstrate good agreement with converged simulations employing explicit models for plasma diffusion and viscosity, suggesting that the implicit sub-grid model used in ILES is sufficient to model these processes in these experiments. In our simulations, mixing is driven by short-wavelength asymmetries and longer-wavelength features are responsible for developing flows that transport mixed material towards the center of the hot spot. Mix material transported by this process is responsible for most of the mix (DT) yield even for the capsule with a CD layer adjacent to the tritium fuel. Consistent with our previous results, mix does not play a significant role in TT neutron yield degradation; instead, this is dominated by the displacement of fuel from the center of the implosion due to the development of turbulent instabilities seeded by long-wavelength asymmetries. Through these processes, the long

Mixing and solid suspension in a stirred precipitator

International Nuclear Information System (INIS)

Chang, T.P.

1986-04-01

Full-scale mixing and solid suspension studies have been conducted to determine the optimum agitator design for precipitators used in plutonium processing. Design considerations include the geometry of precipitator vessels, feed locations, flow patterns, and product requirements. Evaluations of various agitator designs are based on their capabilities: (1) to achieve uniform mixing of reactants in minimum time, (2) to suspend slurry uniformly throughout the vessel, and (3) to minimize power consumption without inducing air entrainment. Tests of full-scale agitator designs showed that significant improvements in mixing, solid suspension, and energy consumption were achieved

Evaluation of the effect of reactant gases mass flow rates on power density in a polymer electrolyte membrane fuel cell

Science.gov (United States)

Kahveci, E. E.; Taymaz, I.

2018-03-01

In this study it was experimentally investigated the effect of mass flow rates of reactant gases which is one of the most important operational parameters of polymer electrolyte membrane (PEM) fuel cell on power density. The channel type is serpentine and single PEM fuel cell has an active area of 25 cm2. Design-Expert 8.0 (trial version) was used with four variables to investigate the effect of variables on the response using. Cell temperature, hydrogen mass flow rate, oxygen mass flow rate and humidification temperature were selected as independent variables. In addition, the power density was used as response to determine the combined effects of these variables. It was kept constant cell and humidification temperatures while changing mass flow rates of reactant gases. From the results an increase occurred in power density with increasing the hydrogen flow rates. But oxygen flow rate does not have a significant effect on power density within determined mass flow rates.

The effects of combined therapy of rheumatoid arthritis on the acute phase reactants.

Science.gov (United States)

Rexhepi, Sylejman; Rexhepi, Mjellma; Sahatçiu-Meka, Vjollca; Pllana, Ejup; Dragusha, Gani; Gashi, Masar; Rexhepi, Blerta

2009-01-01

The paper presents the results of studies of acute phase reactants in the 60 treated patients with rheumatoid arthritis. Patients were divided into two groups, depending on the applied treatment: group I (n = 30) was treated with methotrexate, sulfasalazine and hydroxychloroquine, and group II (n = 30) with methotrexate. The results of our study shows that there is a statistically significant reduction in the value of acute phase reactants and clinical parameters after treatment in both investigated groups of patients, and also a significant statistical difference between the first and second group of treated patients.

Acute-phase reactants in periodontal disease: current concepts and future implications.

Science.gov (United States)

Archana, Vilasan; Ambili, Ranjith; Nisha, Krishnavilasam Jayakumary; Seba, Abraham; Preeja, Chandran

2015-05-01

Periodontal disease has been linked to adverse cardiovascular events by unknown mechanisms. C-reactive protein is a systemic marker released during the acute phase of an inflammatory response and is a prognostic marker for cardiovascular disease, with elevated serum levels being reported during periodontal disease. Studies also reported elevated levels of various other acute-phase reactants in periodontal disease. It has been reported extensively in the literature that treatment of periodontal infections can significantly lower serum levels of C-reactive protein. Therefore, an understanding of the relationship between acute-phase response and the progression of periodontal disease and other systemic health complications would have a profound effect on the periodontal treatment strategies. In view of this fact, the present review highlights an overview of acute-phase reactants and their role in periodontal disease. © 2014 Wiley Publishing Asia Pty Ltd.

Risk of recurrence after a single manic or mixed episode - a systematic review and meta-analysis

DEFF Research Database (Denmark)

Kessing, Lars Vedel; Andersen, Per Kragh; Vinberg, Maj

2017-01-01

OBJECTIVES: For the first time to estimate the risk of recurrence among patients with a single manic/mixed episode by systematically reviewing prior studies on cohorts of adults, and cohorts of children and adolescents, respectively. METHODS: A systematic literature search up to August 2017...... was carried out including studies in which mixed episode at inclusion. RESULTS: Three studies including a total of 293 adult patients with a single manic or mixed episode...... as children and adolescents. It is important that clinicians and patients as well as relatives are well informed about these high risks when deciding to start maintenance treatment or not following onset of a single manic or mixed episode....

Biodegradation of used motor oil by single and mixed cultures of ...

African Journals Online (AJOL)

This study was carried out to evaluate the potential of single and mixed cultures of Nostoc hatei and Synechocystis aquatilis in the biodegradation of 10% used motor oil. The rates of biodegradation of the oil were studied for a period of 21 days under laboratory conditions. Single cultures of N. hatei performed best in the ...

Modeling of the reactant conversion rate in a turbulent shear flow

Science.gov (United States)

Frankel, S. H.; Madnia, C. K.; Givi, P.

1992-01-01

Results are presented of direct numerical simulations (DNS) of spatially developing shear flows under the influence of infinitely fast chemical reactions of the type A + B yields Products. The simulation results are used to construct the compositional structure of the scalar field in a statistical manner. The results of this statistical analysis indicate that the use of a Beta density for the probability density function (PDF) of an appropriate Shvab-Zeldovich mixture fraction provides a very good estimate of the limiting bounds of the reactant conversion rate within the shear layer. This provides a strong justification for the implementation of this density in practical modeling of non-homogeneous turbulent reacting flows. However, the validity of the model cannot be generalized for predictions of higher order statistical quantities. A closed form analytical expression is presented for predicting the maximum rate of reactant conversion in non-homogeneous reacting turbulence.

Elementary Girls' Attitudes toward Mathematics in Mixed-Gender and Single-Gender Classrooms

Science.gov (United States)

Tichenor, Mercedes; Welsh, Alyssa; Corcoran, Carol; Piechura, Kathy; Heins, Elizabeth

2016-01-01

By the time girls are second graders, they may be exhibiting negative attitudes toward math (Cvencek, Meltzoff, & Greenwald, 2011). McFarland, Benson and McFarland (2011) examined girls' math achievement in single-gender and mixed-gender classrooms and suggest that single-gendered formats can help females. In this study, we compare the math…

Transesterification of castor oil usingMgO/SiO2 catalyst and coconutoilas co-reactant

OpenAIRE

Kamisah D. Pandiangan; Novesar Jamarun; Syukri Arief; Wasinton Simanjuntak

2016-01-01

This paper describes the transesterification of castor oil with the use of coconut oil as co-reactant and MgO/SiO2as heterogeneous base catalyst. The catalyst was preparedfrom rice husk silica and magnesium nitrate by sol-gel method, with MgO load of 20% relative to silica, and then subjected to sintering treatment at 600 oC for 6 hours. A series of experiments was carried out, indicating that the use of coconut oil as co-reactant significantly promoted the conversion of castor oil into b...

Mixing subattolitre volumes in a quantitative and highly parallel manner with soft matter nanofluidics

DEFF Research Database (Denmark)

Christensen, Sune M.; Bolinger, Pierre-Yves; Hatzakis, Nikos

2012-01-01

Handling and mixing ultrasmall volumes of reactants in parallel can increase the throughput and complexity of screening assays while simultaneously reducing reagent consumption. Microfabricated silicon and plastic can provide reliable fluidic devices, but cannot typically handle total volumes sma...

The Effects of Single versus Mixed Gender Treatment for Adolescent Girls with ADHD

Science.gov (United States)

Babinski, Dara E.; Sibley, Margaret H.; Ross, J. Megan; Pelham, William E.

2013-01-01

This study evaluated the social behavior of adolescents with attention deficit hyperactivity disorder (ADHD) in single and mixed gender treatment settings. We collected ratings of social behavior (i.e., prosocial peer interactions, assertiveness, self-management, compliance, physical aggression, relational aggression) during single and mixed…

Synthesis of nanoparticles from malleable and ductile metals using powder-free, reactant-assisted mechanical attrition.

Science.gov (United States)

McMahon, Brandon W; Perez, Jesus Paulo L; Yu, Jiang; Boatz, Jerry A; Anderson, Scott L

2014-11-26

A reactant-assisted mechanochemical method was used to produce copious nanoparticles from malleable/ductile metals, demonstrated here for aluminum, iron, and copper. The milling media is intentionally degraded via a reactant-accelerated wear process, where the reactant aids particle production by binding to the metal surfaces, enhancing particle production, and reducing the tendency toward mechanochemical (cold) welding. The mechanism is explored by comparing the effects of different types of solvents and solvent mixtures on the amount and type of particles produced. Particles were functionalized with oleic acid to aid in particle size separation, enhance dispersion in hydrocarbon solvents, and protect the particles from oxidation. For aluminum and iron, the result is air-stable particles, but for copper, the suspended particles are found to dissolve when exposed to air. Characterization was performed using electron microscopy, dynamic light scattering, Fourier transform infrared spectroscopy, solid state nuclear magnetic resonance, and X-ray photoelectron spectroscopy. Density functional theory was used to examine the nature of carboxylic acid binding to the aluminum surface, confirming the dominance of bridging bidentate binding.

High efficiency rubrene based inverted top-emission organic light emitting devices with a mixed single layer

International Nuclear Information System (INIS)

Wang, Zhaokui; Lou, Yanhui; Naka, Shigeki; Okada, Hiroyuki

2010-01-01

Inverted top-emission organic light emitting devices (TEOLEDs) with a mixed single layer by mixing of electron transport materials (PyPySPyPy and Alq 3 ), hole transport material (α-NPD) and dope material (rubrene) were investigated. Maximum power efficiency of 3.5 lm/W and maximum luminance of 7000 cd/m 2 were obtained by optimizing the mixing ratio of PyPySPyPy:Alq 3 :α-NPD:rubrene=25:50:25:1. Luminance and power efficiency of mixed single layer device were two times improved compared to bi-layer heterojunction device and tri-layer heterojunction device. Lifetime test also shows that the mixed single layer device exhibits longer operational lifetimes of 343 h, which is three times longer than the 109 h for tri-layer device, and two times longer than the 158 h for bi-layer device. In addition, the maximum luminance and power efficiency were obtained at 20,000 cd/m 2 and 7.5 lm/W, respectively, when a TPD layer of 45 nm was capped onto the top metal electrode.

Accuracy of Single-Step versus 2-Step Double-Mix Impression Technique

DEFF Research Database (Denmark)

Franco, Eduardo Batista; da Cunha, Leonardo Fernandes; Herrera, Francyle Simões

2011-01-01

Objective. To investigate the accuracy of dies obtained from single-step and 2-step double-mix impressions. Material and Methods. Impressions (n = 10) of a stainless steel die simulating a complete crown preparation were performed using a polyether (Impregum Soft Heavy and Light body) and a vinyl...

Apparatus and method for continuous production of materials

Science.gov (United States)

Chang, Chih-hung; Jin, Hyungdae

2014-08-12

Embodiments of a continuous-flow injection reactor and a method for continuous material synthesis are disclosed. The reactor includes a mixing zone unit and a residence time unit removably coupled to the mixing zone unit. The mixing zone unit includes at least one top inlet, a side inlet, and a bottom outlet. An injection tube, or plurality of injection tubes, is inserted through the top inlet and extends past the side inlet while terminating above the bottom outlet. A first reactant solution flows in through the side inlet, and a second reactant solution flows in through the injection tube(s). With reference to nanoparticle synthesis, the reactant solutions combine in a mixing zone and form nucleated nanoparticles. The nucleated nanoparticles flow through the residence time unit. The residence time unit may be a single conduit, or it may include an outer housing and a plurality of inner tubes within the outer housing.

The general theory of multistage geminate reactions of isolated pairs of reactants. III. Two-stage reversible dissociation in geminate reaction A + A↔C↔B + B

Energy Technology Data Exchange (ETDEWEB)

Kipriyanov, Alexey A.; Kipriyanov, Alexander A.; Doktorov, Alexander B. [Voevodsky Institute of Chemical Kinetics and Combustion, Siberian Branch of the Russian Academy of Sciences, Novosibirsk 630090, Russia and Novosibirsk State University, Novosibirsk 630090 (Russian Federation)

2016-04-14

Specific two-stage reversible reaction A + A↔C↔B + B of the decay of species C reactants by two independent transition channels is considered on the basis of the general theory of multistage reactions of isolated pairs of reactants. It is assumed that at the initial instant of time, the reacting system contains only reactants C. The employed general approach has made it possible to consider, in the general case, the inhomogeneous initial distribution of reactants, and avoid application of model concepts of a reaction system structure (i.e., of the structure of reactants and their molecular mobility). Slowing of multistage reaction kinetics as compared to the kinetics of elementary stages is established and physically interpreted. To test approximations (point approximation) used to develop a universal kinetic law, a widely employed specific model of spherical particles with isotropic reactivity diffusing in solution is applied. With this particular model as an example, ultimate kinetics of chemical conversion of reactants is investigated. The question concerning the depths of chemical transformation at which long-term asymptotes are reached is studied.

C-C Coupling on Single-Atom-Based Heterogeneous Catalyst.

Science.gov (United States)

Zhang, Xiaoyan; Sun, Zaicheng; Wang, Bin; Tang, Yu; Nguyen, Luan; Li, Yuting; Tao, Franklin Feng

2018-01-24

Compared to homogeneous catalysis, heterogeneous catalysis allows for ready separation of products from the catalyst and thus reuse of the catalyst. C-C coupling is typically performed on a molecular catalyst which is mixed with reactants in liquid phase during catalysis. This homogeneous mixing at a molecular level in the same phase makes separation of the molecular catalyst extremely challenging and costly. Here we demonstrated that a TiO 2 -based nanoparticle catalyst anchoring singly dispersed Pd atoms (Pd 1 /TiO 2 ) is selective and highly active for more than 10 Sonogashira C-C coupling reactions (R≡CH + R'X → R≡R'; X = Br, I; R' = aryl or vinyl). The coupling between iodobenzene and phenylacetylene on Pd 1 /TiO 2 exhibits a turnover rate of 51.0 diphenylacetylene molecules per anchored Pd atom per minute at 60 °C, with a low apparent activation barrier of 28.9 kJ/mol and no cost of catalyst separation. DFT calculations suggest that the single Pd atom bonded to surface lattice oxygen atoms of TiO 2 acts as a site to dissociatively chemisorb iodobenzene to generate an intermediate phenyl, which then couples with phenylacetylenyl bound to a surface oxygen atom. This coupling of phenyl adsorbed on Pd 1 and phenylacetylenyl bound to O ad of TiO 2 forms the product molecule, diphenylacetylene.

Study of gel grown mixed crystals of Bax Ca ((IO3) 4

Indian Academy of Sciences (India)

The growth of mixed crystals of BaCa1–(IO3)4 were carried out with simple gel method. The effect of various parameters such as pH of gel solution, gel concentration, gel setting time, concentration of reactants on the growth was studied. Crystals having different morphologies and habits were obtained. The grown ...

Study of the ionization of alkane-electron scavenger reactant mixtures irradiated by 60Co gamma rays

International Nuclear Information System (INIS)

Bonnet, Jacques.

1977-01-01

This study deals with ionization of alkane-electron scavenger reactant mixtures, irradiated by 60 Co γ-rays. It is shown that the extrapolated free-ion yields (extrapolated yield method) decrease with the reactant concentration. On the basis of ONSAGER model and theoretical treatment of MOZUMDER, the cross sections of epithermal electron attachment in hexane, cyclohexane, 2,2-dimethylbutane, cyclopentane, 2,2,4-trimethylpentane for CCl 4 , C 7 F 14 , C 6 H 5 Br, C 6 H 5 Cl, C 6 F 14 , (C 6 H 5 ) 2 are determined. A comparison between gas-phase and liquid-phase cross sections is established [fr

Experimental investigation of laminar LPG-H{sub 2} jet diffusion flame with preheated reactants

Energy Technology Data Exchange (ETDEWEB)

D.P. Mishra; P. Kumar [Indian Institute of Technology, Kanpur (India). Combustion Laboratory, Department of Aerospace Engineering

2008-10-15

This paper presents an experimental investigation of the effect of H{sub 2} addition on flame length, soot free length fraction (SFLF), flame radiant fraction, gas temperature and emission level in LPG-H{sub 2} composite fuel jet diffusion flame for two preheated cases namely, (i) preheated air and (ii) preheated air and fuel. Results show that the H{sub 2} addition leads to a reduction in flame length which may be caused due to an increased gas temperature. Besides this, the flame length is also observed to be reduced with increasing reactants temperature. The soot free length fraction (SFLF) increases as H{sub 2} is added to fuel stream. This might have been caused by decrease in the C/H ratio in the flame and is favorable to attenuate PAH formation rate. Interestingly, the SFLF is observed to be reduced with increasing reactants temperature that may be due to reduction in induction period of soot formation caused by enhanced flame temperature. Moreover, the decreased radiant heat fraction with hydrogen addition is pertinent with the reduction in soot concentration level. The reduction in NOx emission level with H{sub 2} addition to the fuel stream is also observed. On the contrary, NOx emission level is found to be enhanced significantly with reactant temperature that can be attributed to the increase in thermal NOx through Zeldovich mechanism. 31 refs., 4 figs., 2 tabs.

Intercomparison of model simulations of mixed-phase clouds observed during the ARM Mixed-Phase Arctic Cloud Experiment. Part I: Single layer cloud

Energy Technology Data Exchange (ETDEWEB)

Klein, S A; McCoy, R B; Morrison, H; Ackerman, A; Avramov, A; deBoer, G; Chen, M; Cole, J; DelGenio, A; Golaz, J; Hashino, T; Harrington, J; Hoose, C; Khairoutdinov, M; Larson, V; Liu, X; Luo, Y; McFarquhar, G; Menon, S; Neggers, R; Park, S; Poellot, M; von Salzen, K; Schmidt, J; Sednev, I; Shipway, B; Shupe, M; Spangenberg, D; Sud, Y; Turner, D; Veron, D; Falk, M; Foster, M; Fridlind, A; Walker, G; Wang, Z; Wolf, A; Xie, S; Xu, K; Yang, F; Zhang, G

2008-02-27

Results are presented from an intercomparison of single-column and cloud-resolving model simulations of a cold-air outbreak mixed-phase stratocumulus cloud observed during the Atmospheric Radiation Measurement (ARM) program's Mixed-Phase Arctic Cloud Experiment. The observed cloud occurred in a well-mixed boundary layer with a cloud top temperature of -15 C. The observed liquid water path of around 160 g m{sup -2} was about two-thirds of the adiabatic value and much greater than the mass of ice crystal precipitation which when integrated from the surface to cloud top was around 15 g m{sup -2}. The simulations were performed by seventeen single-column models (SCMs) and nine cloud-resolving models (CRMs). While the simulated ice water path is generally consistent with the observed values, the median SCM and CRM liquid water path is a factor of three smaller than observed. Results from a sensitivity study in which models removed ice microphysics indicate that in many models the interaction between liquid and ice-phase microphysics is responsible for the large model underestimate of liquid water path. Despite this general underestimate, the simulated liquid and ice water paths of several models are consistent with the observed values. Furthermore, there is some evidence that models with more sophisticated microphysics simulate liquid and ice water paths that are in better agreement with the observed values, although considerable scatter is also present. Although no single factor guarantees a good simulation, these results emphasize the need for improvement in the model representation of mixed-phase microphysics. This case study, which has been well observed from both aircraft and ground-based remote sensors, could be a benchmark for model simulations of mixed-phase clouds.

A Nanofluidic Mixing Device for High-throughput Fluorescence Sensing of Single Molecules

NARCIS (Netherlands)

Mathwig, Klaus; Fijen, C.; Fontana, M.; Lemay, S.G.; Hohlbein, J.C.

2017-01-01

We introduce a nanofluidic mixing device entirely fabricated in glass for the fluorescence detection of single molecules. The design consists of a nanochannel T-junction and allows the continuous monitoring of chemical or enzymatic reactions of analytes as they arrive from two independent inlets.

Modeling of the interplay between single-file diffusion and conversion reaction in mesoporous systems

Energy Technology Data Exchange (ETDEWEB)

Wang, Jing [Iowa State Univ., Ames, IA (United States)

2013-01-11

We analyze the spatiotemporal behavior of species concentrations in a diffusion-mediated conversion reaction which occurs at catalytic sites within linear pores of nanometer diameter. A strict single-file (no passing) constraint occurs in the diffusion within such narrow pores. Both transient and steady-state behavior is precisely characterized by kinetic Monte Carlo simulations of a spatially discrete lattice–gas model for this reaction–diffusion process considering various distributions of catalytic sites. Exact hierarchical master equations can also be developed for this model. Their analysis, after application of mean-field type truncation approximations, produces discrete reaction–diffusion type equations (mf-RDE). For slowly varying concentrations, we further develop coarse-grained continuum hydrodynamic reaction–diffusion equations (h-RDE) incorporating a precise treatment of single-file diffusion (SFD) in this multispecies system. Noting the shortcomings of mf-RDE and h-RDE, we then develop a generalized hydrodynamic (GH) formulation of appropriate gh-RDE which incorporates an unconventional description of chemical diffusion in mixed-component quasi-single-file systems based on a refined picture of tracer diffusion for finite-length pores. The gh-RDE elucidate the non-exponential decay of the steady-state reactant concentration into the pore and the non-mean-field scaling of the reactant penetration depth. Then an extended model of a catalytic conversion reaction within a functionalized nanoporous material is developed to assess the effect of varying the reaction product – pore interior interaction from attractive to repulsive. The analysis is performed utilizing the generalized hydrodynamic formulation of the reaction-diffusion equations which can reliably capture the complex interplay between reaction and restricted transport for both irreversible and reversible reactions.

Intercomparison of model simulations of mixed-phase clouds observed during the ARM Mixed-Phase Arctic Cloud Experiment. Part I: Single layer cloud

Energy Technology Data Exchange (ETDEWEB)

Klein, Stephen A.; McCoy, Renata B.; Morrison, Hugh; Ackerman, Andrew S.; Avramov, Alexander; de Boer, Gijs; Chen, Mingxuan; Cole, Jason N.S.; Del Genio, Anthony D.; Falk, Michael; Foster, Michael J.; Fridlind, Ann; Golaz, Jean-Christophe; Hashino, Tempei; Harrington, Jerry Y.; Hoose, Corinna; Khairoutdinov, Marat F.; Larson, Vincent E.; Liu, Xiaohong; Luo, Yali; McFarquhar, Greg M.; Menon, Surabi; Neggers, Roel A. J.; Park, Sungsu; Poellot, Michael R.; Schmidt, Jerome M.; Sednev, Igor; Shipway, Ben J.; Shupe, Matthew D.; Spangenberg, Douglas A.; Sud, Yogesh C.; Turner, David D.; Veron, Dana E.; von Salzen, Knut; Walker, Gregory K.; Wang, Zhien; Wolf, Audrey B.; Xie, Shaocheng; Xu, Kuan-Man; Yang, Fanglin; Zhang, Gong

2009-02-02

Results are presented from an intercomparison of single-column and cloud-resolving model simulations of a cold-air outbreak mixed-phase stratocumulus cloud observed during the Atmospheric Radiation Measurement (ARM) program's Mixed-Phase Arctic Cloud Experiment. The observed cloud occurred in a well-mixed boundary layer with a cloud top temperature of -15 C. The observed average liquid water path of around 160 g m{sup -2} was about two-thirds of the adiabatic value and much greater than the average mass of ice crystal precipitation which when integrated from the surface to cloud top was around 15 g m{sup -2}. The simulations were performed by seventeen single-column models (SCMs) and nine cloud-resolving models (CRMs). While the simulated ice water path is generally consistent with the observed values, the median SCM and CRM liquid water path is a factor of three smaller than observed. Results from a sensitivity study in which models removed ice microphysics suggest that in many models the interaction between liquid and ice-phase microphysics is responsible for the large model underestimate of liquid water path. Despite this general underestimate, the simulated liquid and ice water paths of several models are consistent with the observed values. Furthermore, there is evidence that models with more sophisticated microphysics simulate liquid and ice water paths that are in better agreement with the observed values, although considerable scatter is also present. Although no single factor guarantees a good simulation, these results emphasize the need for improvement in the model representation of mixed-phase microphysics.

High-accuracy self-mixing interferometer based on single high-order orthogonally polarized feedback effects.

Science.gov (United States)

Zeng, Zhaoli; Qu, Xueming; Tan, Yidong; Tan, Runtao; Zhang, Shulian

2015-06-29

A simple and high-accuracy self-mixing interferometer based on single high-order orthogonally polarized feedback effects is presented. The single high-order feedback effect is realized when dual-frequency laser reflects numerous times in a Fabry-Perot cavity and then goes back to the laser resonator along the same route. In this case, two orthogonally polarized feedback fringes with nanoscale resolution are obtained. This self-mixing interferometer has the advantages of higher sensitivity to weak signal than that of conventional interferometer. In addition, two orthogonally polarized fringes are useful for discriminating the moving direction of measured object. The experiment of measuring 2.5nm step is conducted, which shows a great potential in nanometrology.

The effect of layer thickness and composition on the kinetics of solid state reactions in the niobium-selenium system studied using superlattice reactants

International Nuclear Information System (INIS)

Fukuto, M.; Kevan, S.D.

1997-01-01

The ability to form an amorphous reaction intermediate by the low temperature interdiffusion of a modulated elemental reactant is shown to be a function of the overall composition as well as elemental layer thicknesses in the niobium-selenium system. For niobium-rich reactants, an amorphous reaction intermediate was observed to form upon low temperature annealing of reactants with modulation thicknesses less than 60 A. Further annealing of the amorphous intermediates led to the crystallization of Nb 2 Se, Nb 5 Se 4 or Nb 3 Se 4 depending upon the overall composition of the amorphous intermediate. Modulated elemental reactants with overall compositions containing more than two-thirds selenium were found to heterogeneously nucleate NbSe 2 at the reacting interfaces. The formation of the thermodynamically expected compounds Nb 2 Se 3 , NbSe 3 , and Nb 2 Se 9 at their respective compositions required extended high temperature annealing to react the dichalcogenide with the remaining elemental reactants. A striking difference between the evolution of the low angle diffraction patterns in these two composition regimes suggests the differences in the reaction kinetics result from a composition dependence of the diffusion coefficients. (orig.)

Physics of reshock and mixing in single-mode Richtmyer-Meshkov instability

International Nuclear Information System (INIS)

Schilling, O; Latini, M; Don, W

2006-01-01

The ninth-order weighted essentially non-oscillatory (WENO) shock-capturing method is used to investigate the physics of reshock and mixing in two-dimensional single-mode Richtmyer-Meshkov instability to late times. The initial conditions and computational domain were adapted from the Mach 1.21 air(acetone)/SF 6 shock tube experiment of Collins and Jacobs [J. Fluid Mech. 464, 113 (2002)]: the growth of the bubble and spike perturbation amplitudes from fifth- and ninth-order WENO simulations of this experiment were compared to the predictions of amplitude growth models, and were shown to be in very good agreement with the experimental data prior to reshock [Latini, Schilling and Don, Phys. Fluids (2007), in press]. In the present investigation, the density, vorticity, baroclinic vorticity production, and simulated density Schlieren fields are first presented to qualitatively describe reshock. The baroclinic circulation deposition on the interface is shown to agree with the predictions of the Samtaney and Zabusky [J. Fluid Mech. 269, 45 (1994)] model and linear instability theory. The time-evolution of the positive and negative circulation on the interface is considered before and after reshock: it is shown that the circulations are equal before, as well as after reshock, until the interaction of the reflected rarefaction with the layer leads to flow symmetry breaking and different evolutions of the positive and negative circulation. The post-reshock mixing layer growth is shown to be in very good agreement with three models predicting linear growth for a short time following reshock. Next, a comprehensive investigation of local and global mixing properties as a function of time is performed. The distribution and amount of mixed fluid along the shock propagation direction is characterized using averaged mole fraction profiles, a fast kinetic reaction model, and molecular mixing fractions. The modal distribution of energy in the mixing layer is quantified using the

Large-Scale Mixed Temperate Forest Mapping at the Single Tree Level using Airborne Laser Scanning

Science.gov (United States)

Scholl, V.; Morsdorf, F.; Ginzler, C.; Schaepman, M. E.

2017-12-01

Monitoring vegetation on a single tree level is critical to understand and model a variety of processes, functions, and changes in forest systems. Remote sensing technologies are increasingly utilized to complement and upscale the field-based measurements of forest inventories. Airborne laser scanning (ALS) systems provide valuable information in the vertical dimension for effective vegetation structure mapping. Although many algorithms exist to extract single tree segments from forest scans, they are often tuned to perform well in homogeneous coniferous or deciduous areas and are not successful in mixed forests. Other methods are too computationally expensive to apply operationally. The aim of this study was to develop a single tree detection workflow using leaf-off ALS data for the canton of Aargau in Switzerland. Aargau covers an area of over 1,400km2 and features mixed forests with various development stages and topography. Forest type was classified using random forests to guide local parameter selection. Canopy height model-based treetop maxima were detected and maintained based on the relationship between tree height and window size, used as a proxy to crown diameter. Watershed segmentation was used to generate crown polygons surrounding each maximum. The location, height, and crown dimensions of single trees were derived from the ALS returns within each polygon. Validation was performed through comparison with field measurements and extrapolated estimates from long-term monitoring plots of the Swiss National Forest Inventory within the framework of the Swiss Federal Institute for Forest, Snow, and Landscape Research. This method shows promise for robust, large-scale single tree detection in mixed forests. The single tree data will aid ecological studies as well as forest management practices. Figure description: Height-normalized ALS point cloud data (top) and resulting single tree segments (bottom) on the Laegeren mountain in Switzerland.

Serum levels of chicken mannan-binding lectin (MBL) during virus infections; indication that chicken MBL is an acute phase reactant

DEFF Research Database (Denmark)

Nielsen, O.L.; Jensenius, J. C.; Jørgensen, Poul Henrik

1999-01-01

Mannan-binding lectin (MBL) is a serum collectin which is believed to be an opsonin of the innate immune defence against various microorganisms. MBL is a minor acute phase reactant in man. We investigated the concentration of serum MBL in chickens infected with infectious bronchitis virus (IBV...... levels returned to normal values 6-10 days after infection. The results indicated that MBL is a minor acute phase reactant in chickens....

The general theory of multistage geminate reactions of isolated pairs of reactants. III. Two-stage reversible dissociation in geminate reaction A + A ↔ C ↔ B + B.

Science.gov (United States)

Kipriyanov, Alexey A; Kipriyanov, Alexander A; Doktorov, Alexander B

2016-04-14

Specific two-stage reversible reaction A + A ↔ C ↔ B + B of the decay of species C reactants by two independent transition channels is considered on the basis of the general theory of multistage reactions of isolated pairs of reactants. It is assumed that at the initial instant of time, the reacting system contains only reactants C. The employed general approach has made it possible to consider, in the general case, the inhomogeneous initial distribution of reactants, and avoid application of model concepts of a reaction system structure (i.e., of the structure of reactants and their molecular mobility). Slowing of multistage reaction kinetics as compared to the kinetics of elementary stages is established and physically interpreted. To test approximations (point approximation) used to develop a universal kinetic law, a widely employed specific model of spherical particles with isotropic reactivity diffusing in solution is applied. With this particular model as an example, ultimate kinetics of chemical conversion of reactants is investigated. The question concerning the depths of chemical transformation at which long-term asymptotes are reached is studied.

Solubilization of Polycyclic Aromatic Hydrocarbons by Single and Binary Mixed Rhamnolipid-Sophorolipid Biosurfactants.

Science.gov (United States)

Song, Dandan; Liang, Shengkang; Yan, Lele; Shang, Yujun; Wang, Xiuli

2016-07-01

Biosurfactants are promising additives for surfactant enhanced remediation (SER) technologies due to their low toxicity and high biodegradability. To develop green and efficient additives for SER, the aqueous solubility enhancements of polycyclic aromatic hydrocarbons (PAHs; naphthalene, phenanthrene, and pyrene) by rhamnolipid (RL) and sophorolipid (SL) biosurfactants were investigated in single and binary mixed systems. The solubilization capacities were quantified in terms of the solubility enhancement factor, molar solubilization ratio (MSR), and micelle-water partition coefficient (). Rughbin's model was applied to evaluate the interaction parameters (β) in the mixed RL-SL micelles. The solubility of the PAHs increased linearly with the glycolipid concentration above the critical micelle concentration (CMC) in both single and mixed systems. Binary RL-SL mixtures exhibited greater solubilization than individual glycolipids. At a SL molar fraction of 0.7 to 0.8, the solubilization capacity was the greatest, and the MSR and reached their maximum values, and β values became positive. These results suggest that the two biosurfactants act synergistically to increase the solubility of the PAHs. The solubilization capacity of the RL-SL mixtures increased with increasing temperature and decreased with increasing salinity. The aqueous solubility of phenanthrene reached a maximum value at pH of 5.5. Moreover, the mixed RL-SL systems exhibited a strong ability to solubilize PAHs, even in the presence of heavy metal ions. These mixed biosurfactant systems have the potential to improve the performance of SER technologies using biosurfactants to solubilize hydrophobic organic contaminants by decreasing the applied biosurfactant concentration, which reduces the costs of remediation. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Effect of single and mixed polycyclic aromatic hydrocarbon contamination on plant biomass yield and PAH dissipation during phytoremediation.

Science.gov (United States)

Afegbua, Seniyat Larai; Batty, Lesley Claire

2018-04-27

Polycyclic aromatic hydrocarbon (PAH)-contaminated sites have a mixture of PAH of varying concentration which may affect PAH dissipation differently to contamination with a single PAH. In this study, pot experiments investigated the impact of PAH contamination on Medicago sativa, Lolium perenne, and Festuca arundinacea biomass and PAH dissipation from soils spiked with phenanthrene (Phe), fluoranthene (Flu), and benzo[a]pyrene (B[a]P) in single and mixed treatments. Stimulatory or inhibitory effects of PAH contamination on plant biomass yields were not different for the single and mixed PAH treatments. Results showed significant effect of PAH treatments on plant growth with an increased root biomass yield for F. arundinacea in the Phe (175%) and Flu (86%) treatments and a root biomass decrease in the mixed treatment (4%). The mean residual PAHs in the planted treatments and unplanted control for the single treatments were not significantly different. B[a]P dissipation was enhanced for single and mixed treatments (71-72%) with F. arundinacea compared to the unplanted control (24-50%). On the other hand, B[a]P dissipation was inhibited with L. perenne (6%) in the single treatment and M. sativa (11%) and L. perenne (29%) in the mixed treatment. Abiotic processes had greater contribution to PAH dissipation compared to rhizodegradation in both treatments. In most cases, a stimulatory effect of PAH contamination on plant biomass yield without an enhancement of PAH dissipation was observed. Plant species among other factors affect the relative contribution of PAH dissipation mechanisms during phytoremediation. These factors determine the effectiveness and suitability of phytoremediation as a remedial strategy for PAH-contaminated sites. Further studies on impact of PAH contamination, plant selection, and rhizosphere activities on soil microbial community structure and remediation outcome are required.

Electrogenerated chemiluminescence of tris(2,2' bipyridine)ruthenium(II) using common biological buffers as co-reactant, pH buffer and supporting electrolyte.

Science.gov (United States)

Kebede, Noah; Francis, Paul S; Barbante, Gregory J; Hogan, Conor F

2015-11-07

A series of aliphatic tertiary amines (HEPES, POPSO, EPPS and BIS-TRIS) commonly used to buffer the pH in biological experiments, were examined as alternative, non-toxic co-reactants for the electrogenerated chemiluminescence (ECL) of tris(2,2'-bipyridine)ruthenium(ii) ([Ru(bpy)3](2+)). These were found to be very attractive as "multi-tasking" reagents, serving not only as co-reactants, but also fulfiling the roles of pH buffer and supporting electrolyte within an aqueous environment; thus significantly simplifying the overall ECL analysis. Sub-nanomolar detection limits were obtained for [Ru(bpy)3](2+) in the presence of BIS-TRIS, making this species an valuable option for co-reactant ECL-based bioanalytical applications.

Catalytic membrane in denitrification of water: a means to facilitate intraporous diffusion of reactants

NARCIS (Netherlands)

Ilinich, O.M.; Cuperus, F.P.; Gemert, van R.W.; Gribov, E.N.; Nosova, L.V.

2000-01-01

The series of mono- and bi-metallic catalysts with Pd and/or Cu supported over γ-Al 2O 3 was investigated with respect to reduction of nitrate and nitrite ions in water by hydrogen. Pronounced limitations of catalytic performance due to intraporous diffusion of the reactants were observed in the

Attempts at estimating mixed venous carbon dioxide tension by the single-breath method.

Science.gov (United States)

Ohta, H; Takatani, O; Matsuoka, T

1989-01-01

The single-breath method was originally proposed by Kim et al. [1] for estimating the blood carbon dioxide tension and cardiac output. Its reliability has not been proven. The present study was undertaken, using dogs, to compare the mixed venous carbon dioxide tension (PVCO2) calculated by the single-breath method with the PVCO2 measured in mixed venous blood, and to evaluate the influence of variations in the exhalation duration and the volume of expired air usually discarded from computations as the deadspace. Among the exhalation durations of 15, 30 and 45 s tested, the 15 s duration was found to be too short to obtain an analyzable O2-CO2 curve, but at either 30 or 45 s, the calculated values of PVCO2 were comparable to the measured PVCO2. A significant agreement between calculated and measured PVCO2 was obtained when the expired gas with PCO2 less than 22 Torr was considered as deadspace gas.

Female Students' Experiences of Computer Technology in Single- versus Mixed-Gender School Settings

Science.gov (United States)

Burke, Lee-Ann; Murphy, Elizabeth

2006-01-01

This study explores how female students compare learning computer technology in a single- versus a mixed- gender school setting. Twelve females participated, all of whom were enrolled in a grade 12 course in Communications' Technology. Data collection included a questionnaire, a semi-structured interview and focus groups. Participants described…

In situ generation of steam and alkaline surfactant for enhanced oil recovery using an exothermic water reactant (EWR)

Science.gov (United States)

Robertson, Eric P

2011-05-24

A method for oil recovery whereby an exothermic water reactant (EWR) encapsulated in a water soluble coating is placed in water and pumped into one or more oil wells in contact with an oil bearing formation. After the water carries the EWR to the bottom of the injection well, the water soluble coating dissolves and the EWR reacts with the water to produce heat, an alkali solution, and hydrogen. The heat from the EWR reaction generates steam, which is forced into the oil bearing formation where it condenses and transfers heat to the oil, elevating its temperature and decreasing the viscosity of the oil. The aqueous alkali solution mixes with the oil in the oil bearing formation and forms a surfactant that reduces the interfacial tension between the oil and water. The hydrogen may be used to react with the oil at these elevated temperatures to form lighter molecules, thus upgrading to a certain extent the oil in situ. As a result, the oil can flow more efficiently and easily through the oil bearing formation towards and into one or more production wells.

Evaluation of Aerosol Mixing State Classes in the GISS Modele-matrix Climate Model Using Single-particle Mass Spectrometry Measurements

Science.gov (United States)

Bauer, Susanne E.; Ault, Andrew; Prather, Kimberly A.

2013-01-01

Aerosol particles in the atmosphere are composed of multiple chemical species. The aerosol mixing state, which describes how chemical species are mixed at the single-particle level, provides critical information on microphysical characteristics that determine the interaction of aerosols with the climate system. The evaluation of mixing state has become the next challenge. This study uses aerosol time-of-flight mass spectrometry (ATOFMS) data and compares the results to those of the Goddard Institute for Space Studies modelE-MATRIX (Multiconfiguration Aerosol TRacker of mIXing state) model, a global climate model that includes a detailed aerosol microphysical scheme. We use data from field campaigns that examine a variety of air mass regimens (urban, rural, and maritime). At all locations, polluted areas in California (Riverside, La Jolla, and Long Beach), a remote location in the Sierra Nevada Mountains (Sugar Pine) and observations from Jeju (South Korea), the majority of aerosol species are internally mixed. Coarse aerosol particles, those above 1 micron, are typically aged, such as coated dust or reacted sea-salt particles. Particles below 1 micron contain large fractions of organic material, internally-mixed with sulfate and black carbon, and few external mixtures. We conclude that observations taken over multiple weeks characterize typical air mass types at a given location well; however, due to the instrumentation, we could not evaluate mass budgets. These results represent the first detailed comparison of single-particle mixing states in a global climate model with real-time single-particle mass spectrometry data, an important step in improving the representation of mixing state in global climate models.

Growth and study of some gel grown group II single crystals of iodate

Indian Academy of Sciences (India)

Unknown

Abstract. Single crystals of calcium iodate and barium iodate were grown by simple gel technique by single diffusion method. The optimum conditions were established by varying various parameters such as pH of gel solution, gel concentration, gel setting time, concentration of the reactants etc. Crystals having different.

Determination of DB10B values of single and mixed cultures of ...

African Journals Online (AJOL)

The survi-ving fraction of isolates decreased with increased irradiation doses. DB10B values of E. coli, S. aureus and S. parat-hyphi B were respectively 0.27, 0.33 and 0.44 kGy when inoculated as single cultures, and 0.24, 0.28 and 0.32 kGy respectively when inoculated as mixed cultures. DB10B values were lower for ...

Teachers' Misconceptions about the Effects of Addition of More Reactants or Products on Chemical Equilibrium

Science.gov (United States)

Cheung, Derek; Ma, Hong-jia; Yang, Jie

2009-01-01

The importance of research on misconceptions about chemical equilibrium is well recognized by educators, but in the past, researchers' interest has centered on student misconceptions and has neglected teacher misconceptions. Focusing on the effects of adding more reactants or products on chemical equilibrium, this article discusses the various…

Antiphase dual-color correlation in a reactant-product pair imparts ultrasensitivity in reaction-linked double-photoswitching fluorescence imaging.

Science.gov (United States)

Wan, Wei; Zhu, Ming-Qiang; Tian, Zhiyuan; Li, Alexander D Q

2015-04-08

A pair of reversible photochemical reactions correlates their reactant and product specifically, and such a correlation uniquely distinguishes their correlated signal from others that are not linked by this reversible reaction. Here a nanoparticle-shielded fluorophore is photodriven to undergo structural dynamics, alternating between a green-fluorescence state and a red-fluorescence state. As time elapses, the fluorophore can be in either state but not both at the same time. Thus, the red fluorescence is maximized while the green fluorescence is minimized and vice versa. Such an antiphase dual-color (AD) corelationship between the red and green fluorescence maxima as well as between their minima can be exploited to greatly improve the signal-to-noise ratio, thus enhancing the ultimate detection limit. Potential benefits of this correlation include elimination of all interferences originating from single-color dyes and signal amplification of AD photoswitching molecules by orders of magnitude.

Design optimization of single mixed refrigerant LNG process using a hybrid modified coordinate descent algorithm

Science.gov (United States)

Qyyum, Muhammad Abdul; Long, Nguyen Van Duc; Minh, Le Quang; Lee, Moonyong

2018-01-01

Design optimization of the single mixed refrigerant (SMR) natural gas liquefaction (LNG) process involves highly non-linear interactions between decision variables, constraints, and the objective function. These non-linear interactions lead to an irreversibility, which deteriorates the energy efficiency of the LNG process. In this study, a simple and highly efficient hybrid modified coordinate descent (HMCD) algorithm was proposed to cope with the optimization of the natural gas liquefaction process. The single mixed refrigerant process was modeled in Aspen Hysys® and then connected to a Microsoft Visual Studio environment. The proposed optimization algorithm provided an improved result compared to the other existing methodologies to find the optimal condition of the complex mixed refrigerant natural gas liquefaction process. By applying the proposed optimization algorithm, the SMR process can be designed with the 0.2555 kW specific compression power which is equivalent to 44.3% energy saving as compared to the base case. Furthermore, in terms of coefficient of performance (COP), it can be enhanced up to 34.7% as compared to the base case. The proposed optimization algorithm provides a deep understanding of the optimization of the liquefaction process in both technical and numerical perspectives. In addition, the HMCD algorithm can be employed to any mixed refrigerant based liquefaction process in the natural gas industry.

Polyimide resin composites via in situ polymerization of monomeric reactants

Science.gov (United States)

Cavano, P. J.

1974-01-01

Thermo-oxidatively stable polyimide/graphite-fiber composites were prepared using a unique in situ polymerization of monomeric reactants directly on reinforcing fibers. This was accomplished by using an aromatic diamine and two ester-acids in a methyl alcohol solvent, rather than a previously synthesized prepolymer varnish, as with other A-type polyimides. A die molding procedure was developed and a composite property characterization conducted with high modulus graphite fiber tow. Flexure, tensile, compressive, and shear tests were conducted at temperatures from 72 to 650 F on laminates before and after exposures at the given temperatures in an air environment for times up to 1000 hours. The composite material was determined to be oxidatively, thermally, and hydrolytically stable.

Quantum-CEP trademark for mixed waste processing

International Nuclear Information System (INIS)

Nahass, P.; Sekula-Moise, P.A.; Chanenchuk, C.A.

1994-01-01

No commercially available technology exists to effectively treat the hundreds of thousands of tons of mixed waste stored and generated in the United States and worldwide. Catalytic Extraction Processing (CEP) is an innovative flexible recycling technology which has inherent advantages for processing mixed wastes in a wide variety of chemical and physical forms. CEP uses a molten metal bath to completely dissociate feeds and recombine them with selected reactants to form useful products. Dissolved carbon in the metal bath creates a reducing atmosphere, readily converting hydrocarbons to synthesis gas, metals to alloys in their reduced state, and inorganics to an engineered ceramic phase. Process conditions can be manipulated to strongly favor partitioning of select radionuclides to a nonleachable vitreous phase, ready for final form disposal. Molten Metal Technology has adapted its CEP technology for radioactive processing and has delivered Quantum-CEP trademark units to customers for demonstration of mixed waste processing leading to commercial scale installations for reducing both private and government inventories. Agreements have also been reached to build commercial CEP facilities to recycle hazardous and industrial wastes

Steady state RANS simulations of temperature fluctuations in single phase turbulent mixing

International Nuclear Information System (INIS)

Kickhofel, J.; Fokken, J.; Kapulla, R.; Prasser, H. M.

2012-01-01

Single phase turbulent mixing in nuclear power plant circuits where a strong temperature gradient is present is known to precipitate pipe failure due to thermal fatigue. Experiments in a square mixing channel offer the opportunity to study the phenomenon under simple and easily reproducible boundary conditions. Measurements of this kind have been performed extensively at the Paul Scherrer Inst. in Switzerland with a high density of instrumentation in the Generic Mixing Experiment (GEMIX). As a fundamental mixing phenomena study closely related to the thermal fatigue problem, the experimental results from GEMIX are valuable for the validation of CFD codes striving to accurately simulate both the temperature and velocity fields in single phase turbulent mixing. In the experiments two iso-kinetic streams meet at a shallow angle of 3 degrees and mix in a straight channel of square cross-section under various degrees of density, temperature, and viscosity stratification over a range of Reynolds numbers ranging from 5*10 3 to 1*10 5 . Conductivity measurements, using wire-mesh and wall sensors, as well as optical measurements, using particle image velocimetry, were conducted with high temporal and spatial resolutions (up to 2.5 kHz and 1 mm in the case of the wire mesh sensor) in the mixing zone, downstream of a splitter plate. The present paper communicates the results of RANS modeling of selected GEMIX tests. Steady-state CFD calculations using a RANS turbulence model represent an inexpensive method for analyzing large and complex components in commercial nuclear reactors, such as the downcomer and reactor pressure vessel heads. Crucial to real world applicability, however, is the ability to model turbulent heat fluctuations in the flow; the Turbulent Heat Flux Transport model developed by ANSYS CFX is capable, by implementation of a transport equation for turbulent heat fluxes, of readily modeling these values. Furthermore, the closure of the turbulent heat flux

Determination of D10 values of single and mixed cultures of bacteria after gamma irradiation

International Nuclear Information System (INIS)

Adu-Gyamfi, A.; Nketsia-Tabiri, J.; Boatin, R.

2009-01-01

The D 10 value of bacteria represents the absorbed radiation dose required to inactivate 90 % of a viable population or reduce the population by a factor of 10. D 10 values of 3 bacterial isolates (Escherichia coli, Staphylococcus aureus and Salmonella parathyphi B) were determined using single and mixed cultures to assess the effect of microbial competition on radiosensitivity. The isolates were inoculated into wakye substrate and exposed to γ-radiation doses of 0, 100, 300, 450, 600, 750, 850 Gy from a 6O Co source at a dose rate of 2.20 kGy/h in air. Enumeration of survivors of the isolates was carried out using serial dilution and pour plate methods. The surviving fraction of isolates decreased with increased irradiation doses. D 10 values of E. coli, S. aureus and S. parathyphi B were respectively 0.27, 0.33 and 0.44 kGy when inoculated as single cultures, and 0.24, 0.28 and 0.32 kGy respectively when inoculated as mixed cultures. D 10 values were lower for mixed cultures compared to single cultures, which might indicate reduced resistance to γ-radiation as a result of competition among the isolates. Microbiological challenge tests based on the D 10 values may result in delivery of higher irradiation doses, but the extra dose could serve as safety margin to enhance the food preservative capacity of radiation processing. (au)

Students' and teachers' perceptions of single-sex and mixed-sex mathematics classes

Science.gov (United States)

Rennie, Léonie J.; Parker, Lesley H.

1997-11-01

This study examines students' perceptions of the learning settings in single-sex and mixed-sex mathematics classes, and teachers' responses to those different classroom contexts. Nearly 300 students in four coeducational secondary schools gave their views of the nature of their participation and interaction in their mathematics classrooms, and data were also obtained from their teachers. There was congruence between students' and teachers' perceptions of the environment in the two kinds of classrooms. Overall, it was perceived that single-sex classrooms provided a more supportive environment for girls, but a rather less supportive environment for boys. Teachers used different strategies with the two kinds of classes and, although many experienced initial difficulty with unruly boys' classes, these problems were overcome. The single-sex environment provided opportunities for teachers to address apparent shortcomings arising from boys' and girls' previous educational experience, which resulted in improved attitudes and performance.

The influence of tertiary butyl hydrazine as a co-reactant on the atomic layer deposition of silver

Energy Technology Data Exchange (ETDEWEB)

Golrokhi, Zahra; Marshall, Paul A.; Romani, Simon [Centre for Materials and Structures, School of Engineering,The University of Liverpool, Liverpool L69 3GH (United Kingdom); Rushworth, Simon [EpiValence, The Wilton Centre, Redcar, Cleveland, TS10 4RF (United Kingdom); Chalker, Paul R. [Centre for Materials and Structures, School of Engineering,The University of Liverpool, Liverpool L69 3GH (United Kingdom); Potter, Richard J., E-mail: rjpott@liverpool.ac.uk [Centre for Materials and Structures, School of Engineering,The University of Liverpool, Liverpool L69 3GH (United Kingdom)

2017-03-31

Highlights: • We demonstrate metallic silver growth by direct liquid injection thermal ALD. • A substituted hydrazine is used as a powerful reducing agent for the first time. • The hydrazine extends the ALD temperature window compared with alcohol. • Hydrazine promotes a more planar growth mode compared to alcohol. • Film adhesion is improved using hydrazine compared with alcohol. - Abstract: Ultra-thin conformal silver films are the focus of development for applications such as anti-microbial surfaces, optical components and electronic devices. In this study, metallic silver films have been deposited using direct liquid injection thermal atomic layer deposition (ALD) using (hfac)Ag(1,5-COD) ((hexafluoroacetylacetonato)silver(I)(1,5-cyclooctadiene)) as the metal source and tertiary butyl hydrazine (TBH) as a co-reactant. The process provides a 23 °C wide ‘self-limiting’ ALD temperature window between 105 and 128 °C, which is significantly wider than is achievable using alcohol as a co-reactant. A mass deposition rate of ∼20 ng/cm{sup 2}/cycle (∼0.18 Å/cycle) is observed under self-limiting growth conditions. The resulting films are crystalline metallic silver with a near planar film-like morphology which are electrically conductive. By extending the temperature range of the ALD window by the use of TBH as a co-reactant, it is envisaged that the process will be exploitable in a range of new low temperature applications.

From single-species advice to mixed-species management: taking the next step

DEFF Research Database (Denmark)

Vinther, Morten; Reeves, S.A.; Patterson, K.R.

2004-01-01

Fishery management advice has traditionally been given on a stock-by-stock basis. Recent problems in implementing this advice, particularly for the demersal fisheries of the North Sea, have highlighted the limitations of the approach. In the long term, it would be desirable to give advice...... that accounts for mixed-fishery effects, but in the short term there is a need for approaches to resolve the conflicting management advice for different species within the same fishery, and to generate catch or effort advice that accounts for the mixed-species nature of the fishery. This paper documents...... a recent approach used to address these problems. The approach takes the single-species advice for each species in the fishery as a starting point, then attempts to resolve it into consistent catch or effort advice using fleet-disaggregated catch forecasts in combination with explicitly stated management...

Single-phase and two-phase gas-liquid turbulent mixing between subchannels in a simulated rod bundle

International Nuclear Information System (INIS)

Sadatomi, Michio; Kawahara, Akimaro; Sato, Yoshifusa; Tomino, Takayoshi.

1996-01-01

This study is concerned with turbulent mixing which is one of the three mechanisms of cross flows between subchannels in a nuclear fuel rod bundle. The channel used in this experiments was a vertical simulated rod bundle having two subchannels connected through 1 to 3 gaps between two rods and/or rod and channel wall. The number of the gaps was changed to investigate the effect of the number on the turbulent mixing. Turbulent mixing rates of air and water and fluctuations of pressure difference between the subchannels were measured for single-phase and two-phase gas-liquid flows under hydrodynamic equilibrium flow conditions. It has been confirmed that the turbulent mixing rate is affected strongly by the fluctuations especially for liquid phase in two-phase slug or churn flow. (author)

Use of periodic variations of reactant concentrations in time resolved ftir studies of CO oxidation on Pd/ZrO{sub 2} catalysts

Energy Technology Data Exchange (ETDEWEB)

Ortelli, E; Wokaun, A [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

1999-08-01

Sine wave modulation of feed concentrations was used to induce dynamic variations in the concentrations of products, intermediates and reactants, which were monitored in a diffuse reflectance FTIR (DRIFT) cell. The phase shift {Delta}{phi} between the external perturbation of the feed and the signals of products, intermediates and reactants was examined in dependence on the modulation frequency {omega}. Reaction constants of a simplified model mechanism were estimated for a Pd{sub 25}Zr{sub 75} based catalyst for CO oxidation. (author) 1 fig., 2 refs.

Quantitative determination of carbonaceous particle mixing state in Paris using single particle mass spectrometer and aerosol mass spectrometer measurements

Science.gov (United States)

Healy, R. M.; Sciare, J.; Poulain, L.; Crippa, M.; Wiedensohler, A.; Prévôt, A. S. H.; Baltensperger, U.; Sarda-Estève, R.; McGuire, M. L.; Jeong, C.-H.; McGillicuddy, E.; O'Connor, I. P.; Sodeau, J. R.; Evans, G. J.; Wenger, J. C.

2013-04-01

Single particle mixing state information can be a powerful tool for assessing the relative impact of local and regional sources of ambient particulate matter in urban environments. However, quantitative mixing state data are challenging to obtain using single particle mass spectrometers. In this study, the quantitative chemical composition of carbonaceous single particles has been estimated using an aerosol time-of-flight mass spectrometer (ATOFMS) as part of the MEGAPOLI 2010 winter campaign in Paris, France. Relative peak areas of marker ions for elemental carbon (EC), organic aerosol (OA), ammonium, nitrate, sulphate and potassium were compared with concurrent measurements from an Aerodyne high resolution time-of-flight aerosol mass spectrometer (HR-ToF-AMS), a thermal/optical OCEC analyser and a particle into liquid sampler coupled with ion chromatography (PILS-IC). ATOFMS-derived mass concentrations reproduced the variability of these species well (R2 = 0.67-0.78), and ten discrete mixing states for carbonaceous particles were identified and quantified. Potassium content was used to identify particles associated with biomass combustion. The chemical mixing state of HR-ToF-AMS organic aerosol factors, resolved using positive matrix factorization, was also investigated through comparison with the ATOFMS dataset. The results indicate that hydrocarbon-like OA (HOA) detected in Paris is associated with two EC-rich mixing states which differ in their relative sulphate content, while fresh biomass burning OA (BBOA) is associated with two mixing states which differ significantly in their OA/EC ratios. Aged biomass burning OA (OOA2-BBOA) was found to be significantly internally mixed with nitrate, while secondary, oxidized OA (OOA) was associated with five particle mixing states, each exhibiting different relative secondary inorganic ion content. Externally mixed secondary organic aerosol was not observed. These findings demonstrate the heterogeneity of primary and

Quantitative determination of carbonaceous particle mixing state in Paris using single-particle mass spectrometer and aerosol mass spectrometer measurements

Directory of Open Access Journals (Sweden)

R. M. Healy

2013-09-01

Full Text Available Single-particle mixing state information can be a powerful tool for assessing the relative impact of local and regional sources of ambient particulate matter in urban environments. However, quantitative mixing state data are challenging to obtain using single-particle mass spectrometers. In this study, the quantitative chemical composition of carbonaceous single particles has been determined using an aerosol time-of-flight mass spectrometer (ATOFMS as part of the MEGAPOLI 2010 winter campaign in Paris, France. Relative peak areas of marker ions for elemental carbon (EC, organic aerosol (OA, ammonium, nitrate, sulfate and potassium were compared with concurrent measurements from an Aerodyne high-resolution time-of-flight aerosol mass spectrometer (HR-ToF-AMS, a thermal–optical OCEC analyser and a particle into liquid sampler coupled with ion chromatography (PILS-IC. ATOFMS-derived estimated mass concentrations reproduced the variability of these species well (R2 = 0.67–0.78, and 10 discrete mixing states for carbonaceous particles were identified and quantified. The chemical mixing state of HR-ToF-AMS organic aerosol factors, resolved using positive matrix factorisation, was also investigated through comparison with the ATOFMS dataset. The results indicate that hydrocarbon-like OA (HOA detected in Paris is associated with two EC-rich mixing states which differ in their relative sulfate content, while fresh biomass burning OA (BBOA is associated with two mixing states which differ significantly in their OA / EC ratios. Aged biomass burning OA (OOA2-BBOA was found to be significantly internally mixed with nitrate, while secondary, oxidised OA (OOA was associated with five particle mixing states, each exhibiting different relative secondary inorganic ion content. Externally mixed secondary organic aerosol was not observed. These findings demonstrate the range of primary and secondary organic aerosol mixing states in Paris. Examination of the

Quantitative determination of carbonaceous particle mixing state in Paris using single-particle mass spectrometer and aerosol mass spectrometer measurements

Science.gov (United States)

Healy, R. M.; Sciare, J.; Poulain, L.; Crippa, M.; Wiedensohler, A.; Prévôt, A. S. H.; Baltensperger, U.; Sarda-Estève, R.; McGuire, M. L.; Jeong, C.-H.; McGillicuddy, E.; O'Connor, I. P.; Sodeau, J. R.; Evans, G. J.; Wenger, J. C.

2013-09-01

Single-particle mixing state information can be a powerful tool for assessing the relative impact of local and regional sources of ambient particulate matter in urban environments. However, quantitative mixing state data are challenging to obtain using single-particle mass spectrometers. In this study, the quantitative chemical composition of carbonaceous single particles has been determined using an aerosol time-of-flight mass spectrometer (ATOFMS) as part of the MEGAPOLI 2010 winter campaign in Paris, France. Relative peak areas of marker ions for elemental carbon (EC), organic aerosol (OA), ammonium, nitrate, sulfate and potassium were compared with concurrent measurements from an Aerodyne high-resolution time-of-flight aerosol mass spectrometer (HR-ToF-AMS), a thermal-optical OCEC analyser and a particle into liquid sampler coupled with ion chromatography (PILS-IC). ATOFMS-derived estimated mass concentrations reproduced the variability of these species well (R2 = 0.67-0.78), and 10 discrete mixing states for carbonaceous particles were identified and quantified. The chemical mixing state of HR-ToF-AMS organic aerosol factors, resolved using positive matrix factorisation, was also investigated through comparison with the ATOFMS dataset. The results indicate that hydrocarbon-like OA (HOA) detected in Paris is associated with two EC-rich mixing states which differ in their relative sulfate content, while fresh biomass burning OA (BBOA) is associated with two mixing states which differ significantly in their OA / EC ratios. Aged biomass burning OA (OOA2-BBOA) was found to be significantly internally mixed with nitrate, while secondary, oxidised OA (OOA) was associated with five particle mixing states, each exhibiting different relative secondary inorganic ion content. Externally mixed secondary organic aerosol was not observed. These findings demonstrate the range of primary and secondary organic aerosol mixing states in Paris. Examination of the temporal

Corrosion of Bronzes by Extended Wetting with Single versus Mixed Acidic Pollutants

Directory of Open Access Journals (Sweden)

Liliana Gianni

2014-04-01

Full Text Available The corrosion of bronzes was examined in the context of single-acid versus mixed-acid (as in urban acid rain solutions. Two bi-component bronzes (copper with either 3% Sn or 7% Sn that closely represent those of historic artifacts were immersed for five weeks in conditions designed to replicate those experienced by statues and ornaments in cities where rainfall and humidity constantly produce an electrolyte layer on the surfaces of bronzes. Ions, acids, and particles of pollutants can dissolve in this layer, resulting in a variety of harsh corrosion processes. The kinetics of corrosion and the properties of the resulting patinas were monitored weekly by electrochemical impedance spectroscopy and open-circuit potential measurements. The sizes and appearances of the corrosion products were monitored and used to estimate the progress of the corrosion, whose crystalline structures were visualized using scanning electron microscopy with energy dispersive spectroscopy, identified by X-ray diffraction, and characterized by spectrocolorimetry. The electrochemical measurements demonstrated that greater damage (in terms of color change and corrosion product formation did not correspond to deficiencies in protection. The mixed-acid solution did not corrode the bronzes, as would be expected from the additive effects of the single acids. The postulated mechanisms of metal dissolution appear to be specific to a particular bronze alloy, with the tin component playing an important role.

Ferrimagnetic Properties of Bond Dilution Mixed Blume-Capel Model with Random Single-Ion Anisotropy

International Nuclear Information System (INIS)

Liu Lei; Yan Shilei

2005-01-01

We study the ferrimagnetic properties of spin 1/2 and spin-1 systems by means of the effective field theory. The system is considered in the framework of bond dilution mixed Blume-Capel model (BCM) with random single-ion anisotropy. The investigation of phase diagrams and magnetization curves indicates the existence of induced magnetic ordering and single or multi-compensation points. Special emphasis is placed on the influence of bond dilution and random single-ion anisotropy on normal or induced magnetic ordering states and single or multi-compensation points. Normal magnetic ordering states take on new phase diagrams with increasing randomness (bond and anisotropy), while anisotropy induced magnetic ordering states are always occurrence no matter whether concentration of anisotropy is large or small. Existence and disappearance of compensation points rely strongly on bond dilution and random single-ion anisotropy. Some results have not been revealed in previous papers and predicted by Neel theory of ferrimagnetism.

Mixed-layered bismuth--oxygen--iodine materials for capture and waste disposal of radioactive iodine

Science.gov (United States)

Krumhansl, James L; Nenoff, Tina M

2015-01-06

Materials and methods of synthesizing mixed-layered bismuth oxy-iodine materials, which can be synthesized in the presence of aqueous radioactive iodine species found in caustic solutions (e.g. NaOH or KOH). This technology provides a one-step process for both iodine sequestration and storage from nuclear fuel cycles. It results in materials that will be durable for repository conditions much like those found in Waste Isolation Pilot Plant (WIPP) and estimated for Yucca Mountain (YMP). By controlled reactant concentrations, optimized compositions of these mixed-layered bismuth oxy-iodine inorganic materials are produced that have both a high iodine weight percentage and a low solubility in groundwater environments.

Mixed-layered bismuth-oxygen-iodine materials for capture and waste disposal of radioactive iodine

Science.gov (United States)

Krumhansl, James L; Nenoff, Tina M

2013-02-26

Materials and methods of synthesizing mixed-layered bismuth oxy-iodine materials, which can be synthesized in the presence of aqueous radioactive iodine species found in caustic solutions (e.g. NaOH or KOH). This technology provides a one-step process for both iodine sequestration and storage from nuclear fuel cycles. It results in materials that will be durable for repository conditions much like those found in Waste Isolation Pilot Plant (WIPP) and estimated for Yucca Mountain (YMP). By controlled reactant concentrations, optimized compositions of these mixed-layered bismuth oxy-iodine inorganic materials are produced that have both a high iodine weight percentage and a low solubility in groundwater environments.

The conversion of BTEX compounds by single and defined mixed cultures to medium-chain-length polyhydroxyalkanoate.

Science.gov (United States)

Nikodinovic, Jasmina; Kenny, Shane T; Babu, Ramesh P; Woods, Trevor; Blau, Werner J; O'Connor, Kevin E

2008-09-01

Here, we report the use of petrochemical aromatic hydrocarbons as a feedstock for the biotechnological conversion into valuable biodegradable plastic polymers--polyhydroxyalkanoates (PHAs). We assessed the ability of the known Pseudomonas putida species that are able to utilize benzene, toluene, ethylbenzene, p-xylene (BTEX) compounds as a sole carbon and energy source for their ability to produce PHA from the single substrates. P. putida F1 is able to accumulate medium-chain-length (mcl) PHA when supplied with toluene, benzene, or ethylbenzene. P. putida mt-2 accumulates mcl-PHA when supplied with toluene or p-xylene. The highest level of PHA accumulated by cultures in shake flask was 26% cell dry weight for P. putida mt-2 supplied with p-xylene. A synthetic mixture of benzene, toluene, ethylbenzene, p-xylene, and styrene (BTEXS) which mimics the aromatic fraction of mixed plastic pyrolysis oil was supplied to a defined mixed culture of P. putida F1, mt-2, and CA-3 in the shake flasks and fermentation experiments. PHA was accumulated to 24% and to 36% of the cell dry weight of the shake flask and fermentation grown cultures respectively. In addition a three-fold higher cell density was achieved with the mixed culture grown in the bioreactor compared to shake flask experiments. A run in the 5-l fermentor resulted in the utilization of 59.6 g (67.5 ml) of the BTEXS mixture and the production of 6 g of mcl-PHA. The monomer composition of PHA accumulated by the mixed culture was the same as that accumulated by single strains supplied with single substrates with 3-hydroxydecanoic acid occurring as the predominant monomer. The purified polymer was partially crystalline with an average molecular weight of 86.9 kDa. It has a thermal degradation temperature of 350 degrees C and a glass transition temperature of -48.5 degrees C.

Race, Identity and the Transference/Countertransference: A Mixed –Race Patient and a Mixed-Race Therapist- A Single Case Study

OpenAIRE

Millar, Tennyson

2014-01-01

This thesis is a single case-study of a child and adolescent psychotherapist working with a fourteen year old female adolescent patient of similar mixed ethnic background. The thesis presents the completed two year therapeutic work which included periods of intensive therapy (3-4 times-a-week work) following less intensive work.\\ud The patient’s early life was marked by witnessing parental domestic violence and parents who divorced. She subsequently struggled with maintaining relationships an...

Non-Fermi Liquid Behavior in the Single-Impurity Mixed Valence Problem

Science.gov (United States)

Zhang, Guang-Ming; Su, Zhao-Bin; Yu, Lu

An effective Hamiltonian of the Anderson single-impurity model with finite-range Coulomb interactions is derived near a particular limit, which is analogous to the Toulouse limit of the ordinary Kondo problem, and the physical properties around the mixed valence quantum critical point are calculated. At this quantum critical point, the local moment is only partially quenched and X-ray edge singularities are exhibited. Around this point, a new type of non-Fermi liquid behavior is predicted with an extra specific heat Cimp ~ T1/4 + AT ln T and spin-susceptibility χimp ~T-3/4 + B ln T.

N-of-1-pathways MixEnrich: advancing precision medicine via single-subject analysis in discovering dynamic changes of transcriptomes.

Science.gov (United States)

Li, Qike; Schissler, A Grant; Gardeux, Vincent; Achour, Ikbel; Kenost, Colleen; Berghout, Joanne; Li, Haiquan; Zhang, Hao Helen; Lussier, Yves A

2017-05-24

Transcriptome analytic tools are commonly used across patient cohorts to develop drugs and predict clinical outcomes. However, as precision medicine pursues more accurate and individualized treatment decisions, these methods are not designed to address single-patient transcriptome analyses. We previously developed and validated the N-of-1-pathways framework using two methods, Wilcoxon and Mahalanobis Distance (MD), for personal transcriptome analysis derived from a pair of samples of a single patient. Although, both methods uncover concordantly dysregulated pathways, they are not designed to detect dysregulated pathways with up- and down-regulated genes (bidirectional dysregulation) that are ubiquitous in biological systems. We developed N-of-1-pathways MixEnrich, a mixture model followed by a gene set enrichment test, to uncover bidirectional and concordantly dysregulated pathways one patient at a time. We assess its accuracy in a comprehensive simulation study and in a RNA-Seq data analysis of head and neck squamous cell carcinomas (HNSCCs). In presence of bidirectionally dysregulated genes in the pathway or in presence of high background noise, MixEnrich substantially outperforms previous single-subject transcriptome analysis methods, both in the simulation study and the HNSCCs data analysis (ROC Curves; higher true positive rates; lower false positive rates). Bidirectional and concordant dysregulated pathways uncovered by MixEnrich in each patient largely overlapped with the quasi-gold standard compared to other single-subject and cohort-based transcriptome analyses. The greater performance of MixEnrich presents an advantage over previous methods to meet the promise of providing accurate personal transcriptome analysis to support precision medicine at point of care.

Catalysis on singly dispersed bimetallic sites

Science.gov (United States)

Zhang, Shiran; Nguyen, Luan; Liang, Jin-Xia; Shan, Junjun; Liu, Jingyue; Frenkel, Anatoly I.; Patlolla, Anitha; Huang, Weixin; Li, Jun; Tao, Franklin

2015-08-01

A catalytic site typically consists of one or more atoms of a catalyst surface that arrange into a configuration offering a specific electronic structure for adsorbing or dissociating reactant molecules. The catalytic activity of adjacent bimetallic sites of metallic nanoparticles has been studied previously. An isolated bimetallic site supported on a non-metallic surface could exhibit a distinctly different catalytic performance owing to the cationic state of the singly dispersed bimetallic site and the minimized choices of binding configurations of a reactant molecule compared with continuously packed bimetallic sites. Here we report that isolated Rh1Co3 bimetallic sites exhibit a distinctly different catalytic performance in reduction of nitric oxide with carbon monoxide at low temperature, resulting from strong adsorption of two nitric oxide molecules and a nitrous oxide intermediate on Rh1Co3 sites and following a low-barrier pathway dissociation to dinitrogen and an oxygen atom. This observation suggests a method to develop catalysts with high selectivity.

Mixed Schools versus Single-Sex Schools: Are There Differences in the Academic Results for Boys and Girls in Catalonia?

Science.gov (United States)

Garcia-Gracia, Maribel; Donoso Vázquez, Trinidad

2016-01-01

This study carries out a comparative analysis of achievement according to gender between mixed and single-sex schools in the region of Catalonia, Spain, for the subjects of Spanish, Catalan, English and Mathematics. After a brief contextualisation, a review of the main findings from international studies on differences in results for mixed schools…

Probing the type of anomalous diffusion with single-particle tracking.

Science.gov (United States)

Ernst, Dominique; Köhler, Jürgen; Weiss, Matthias

2014-05-07

Many reactions in complex fluids, e.g. signaling cascades in the cytoplasm of living cells, are governed by a diffusion-driven encounter of reactants. Yet, diffusion in complex fluids often exhibits an anomalous characteristic ('subdiffusion'). Since different types of subdiffusion have distinct effects on timing and equilibria of chemical reactions, a thorough determination of the reactants' type of random walk is key to a quantitative understanding of reactions in complex fluids. Here we introduce a straightforward and simple approach for determining the type of subdiffusion from single-particle tracking data. Unlike previous approaches, our method also is sensitive to transient subdiffusion phenomena, e.g. obstructed diffusion below the percolation threshold. We validate our strategy with data from experiment and simulation.

Kinetics of the glucose/glycine Maillard reaction pathways: influences of pH and reactant initial concentrations

NARCIS (Netherlands)

Martins, S.I.F.S.; Boekel, van M.A.J.S.

2005-01-01

A previously proposed kinetic model for the glucose/glycine Maillard reaction pathways has been validated by changing the initial pH (4.8, 5.5, 6.0, 6.8 and 7.5) of the reaction and reactant initial concentrations (1:2 and 2:1 molar ratios were compared to the 1:1 ratio). The model consists of 10

Generalized hydrodynamic treatment of the interplay between restricted transport and catalytic reactions in nanoporous materials.

Science.gov (United States)

Ackerman, David M; Wang, Jing; Evans, James W

2012-06-01

Behavior of catalytic reactions in narrow pores is controlled by a delicate interplay between fluctuations in adsorption-desorption at pore openings, restricted diffusion, and reaction. This behavior is captured by a generalized hydrodynamic formulation of appropriate reaction-diffusion equations (RDE). These RDE incorporate an unconventional description of chemical diffusion in mixed-component quasi-single-file systems based on a refined picture of tracer diffusion for finite-length pores. The RDE elucidate the nonexponential decay of the steady-state reactant concentration into the pore and the non-mean-field scaling of the reactant penetration depth.

Modification of the liquid cooling channel of PEMFCs for their operation with dry reactant gases

International Nuclear Information System (INIS)

Shyu, Jin-Cherng; Hsueh, Kan-Lin; Tsau, Fanghei; Chen, Fa-Lin

2011-01-01

In order to tackle both water and thermal problems, a modified PEMFC is proposed in the present study for its operation with dry reactant gases via the modification of liquid cooling channel with circulating liquid electrolyte. Fuel cell with both circulating liquid electrolyte and solid polymer membrane operated with either dry or humidified H 2 /O 2 is compared in the present study at temperatures of 40, 50, 65, and 80 o C, respectively. The measured E-I data show that such single cell can be operated at 80 o C without humidification. Besides, a semi-empirical equation to predict the current/voltage relationship, and the electrochemical impedance method are also employed in the present study for cell resistance analysis. The analysis results show that the high interfacial resistance should be one of the major reasons for the inferior performance of the present cell. Based on the discovery, an improvement of the present fuel cell is further proposed by Nafion ionomer spreading on the electrode before the assembly of membrane and electrode. The maximum power density of the cell after electrode treatment reaches 75 mW/cm 2 for dry H 2 /O 2 operation at 0.4 V, which is almost threefold improvement compared with that without electrode treatment.

Measurements of an ablator-gas atomic mix in indirectly driven implosions at the National Ignition Facility.

Science.gov (United States)

Smalyuk, V A; Tipton, R E; Pino, J E; Casey, D T; Grim, G P; Remington, B A; Rowley, D P; Weber, S V; Barrios, M; Benedetti, L R; Bleuel, D L; Bradley, D K; Caggiano, J A; Callahan, D A; Cerjan, C J; Clark, D S; Edgell, D H; Edwards, M J; Frenje, J A; Gatu-Johnson, M; Glebov, V Y; Glenn, S; Haan, S W; Hamza, A; Hatarik, R; Hsing, W W; Izumi, N; Khan, S; Kilkenny, J D; Kline, J; Knauer, J; Landen, O L; Ma, T; McNaney, J M; Mintz, M; Moore, A; Nikroo, A; Pak, A; Parham, T; Petrasso, R; Sayre, D B; Schneider, M B; Tommasini, R; Town, R P; Widmann, K; Wilson, D C; Yeamans, C B

2014-01-17

We present the first results from an experimental campaign to measure the atomic ablator-gas mix in the deceleration phase of gas-filled capsule implosions on the National Ignition Facility. Plastic capsules containing CD layers were filled with tritium gas; as the reactants are initially separated, DT fusion yield provides a direct measure of the atomic mix of ablator into the hot spot gas. Capsules were imploded with x rays generated in hohlraums with peak radiation temperatures of ∼294  eV. While the TT fusion reaction probes conditions in the central part (core) of the implosion hot spot, the DT reaction probes a mixed region on the outer part of the hot spot near the ablator-hot-spot interface. Experimental data were used to develop and validate the atomic-mix model used in two-dimensional simulations.

Mixed-mode modelling mixing methodologies for organisational intervention

CERN Document Server

Clarke, Steve; Lehaney, Brian

2001-01-01

The 1980s and 1990s have seen a growing interest in research and practice in the use of methodologies within problem contexts characterised by a primary focus on technology, human issues, or power. During the last five to ten years, this has given rise to challenges regarding the ability of a single methodology to address all such contexts, and the consequent development of approaches which aim to mix methodologies within a single problem situation. This has been particularly so where the situation has called for a mix of technological (the so-called 'hard') and human­ centred (so-called 'soft') methods. The approach developed has been termed mixed-mode modelling. The area of mixed-mode modelling is relatively new, with the phrase being coined approximately four years ago by Brian Lehaney in a keynote paper published at the 1996 Annual Conference of the UK Operational Research Society. Mixed-mode modelling, as suggested above, is a new way of considering problem situations faced by organisations. Traditional...

Experimental analysis of the effects of the operating variables on the performance of a single PEMFC

International Nuclear Information System (INIS)

Santarelli, M.G.; Torchio, M.F.

2007-01-01

This paper shows and discusses the results obtained after an experimental session devoted to characterization of the behavior of a single proton exchange membrane fuel cell (PEMFC) with variation of the values of six operation variables: cell temperature; anode flow temperature in saturation and dry conditions; cathode flow temperature in saturation and dry conditions; and reactants pressure. The fuel cell employed for the experiments is a single PEMFC with a 25 cm 2 Nafion[reg] 115 membrane. As expected, a higher cell temperature increases the membrane conductivity and the exchange current density with an improvement of the cell behaviour. An increase in the reactant saturation temperature also leads to a better performance, especially in the case of low and medium loads. Conversely, in the case of a low cell temperature, it is better to reduce the water inlet mass flow at high loads to avoid electrode flooding. With an increase of the reactant operating pressure, the maximum of the power curve shifts to higher current densities, and this could be linked to the corresponding shift of the limiting current density. A combined effect of humidification and operating pressure was observed: the increase of operating pressure did not offer a significant improvement when the reactants were dry, while leading to improvements when a partial humidification (only at the anode) was adopted. The best improvements due to a pressure increase were observed when both anode and cathode are humidified. Finally, some tests of other authors at the same operation conditions have been considered, and a comparison has been done

Single and multiple ionization of sulfur atoms by electron impact

International Nuclear Information System (INIS)

Ziegler, D.L.

1982-01-01

Laboratory measurements of the cross sections for single, double, triple, and quadruple ionization of sulfur atoms by electron impact are presented for collision energies from threshold to 500 eV. The cross sections for single ionization of sulfur are measured relative to those of several elements whose absolute cross sections for single ionization are known. Cross sections for each multiple ionization process are then measured relative to those for single ionization. The configuration and operation of the apparatus for these measurements are described. The possible effects of excited sulfur reactants are examined, and the reported cross sections are felt to be characteristic of ground state sulfur atoms

Computational Modelling of Thermal Stability in a Reactive Slab with Reactant Consumption

Directory of Open Access Journals (Sweden)

O. D. Makinde

2012-01-01

Full Text Available This paper investigates both the transient and the steady state of a one-step nth-order oxidation exothermic reaction in a slab of combustible material with an insulated lower surface and an isothermal upper surface, taking into consideration reactant consumption. The nonlinear partial differential equation governing the transient reaction-diffusion problem is solved numerically using a semidiscretization finite difference technique. The steady-state problem is solved using a perturbation technique together with a special type of the Hermite-Padé approximants. Graphical results are presented and discussed quantitatively with respect to various embedded parameters controlling the systems. The crucial roles played by the boundary conditions in determining the thermal ignition criticality are demonstrated.

Non-equilibrium reactive flux: A unified framework for slow and fast reaction kinetics.

Science.gov (United States)

Bose, Amartya; Makri, Nancy

2017-10-21

The flux formulation of reaction rate theory is recast in terms of the expectation value of the reactive flux with an initial condition that corresponds to a non-equilibrium, factorized reactant density. In the common case of slow reactive processes, the non-equilibrium expression reaches the plateau regime only slightly slower than the equilibrium flux form. When the reactants are described by a single quantum state, as in the case of electron transfer reactions, the factorized reactant density describes the true initial condition of the reactive process. In such cases, the time integral of the non-equilibrium flux expression yields the reactant population as a function of time, allowing characterization of the dynamics in cases where there is no clear separation of time scales and thus a plateau regime cannot be identified. The non-equilibrium flux offers a unified approach to the kinetics of slow and fast chemical reactions and is ideally suited to mixed quantum-classical methods.

Degenerate mixing of plasma waves on cold, magnetized single-species plasmas

Science.gov (United States)

Anderson, M. W.; O'Neil, T. M.; Dubin, D. H. E.; Gould, R. W.

2011-10-01

In the cold-fluid dispersion relation ω =ωp/[1+(k⊥/kz)2]1/2 for Trivelpiece-Gould waves on an infinitely long magnetized plasma cylinder, the transverse and axial wavenumbers appear only in the combination k⊥/kz. As a result, for any frequency ω plasma column, these degenerate waves reflect into one another at the ends; thus, each standing-wave normal mode of the bounded plasma is a mixture of many degenerate waves, not a single standing wave as is often assumed. A striking feature of the many-wave modes is that the short-wavelength waves often add constructively along resonance cones given by dz /dr=±(ωp2/ω2-1)1/2. Also, the presence of short wavelengths in the admixture for a predominantly long-wavelength mode enhances the viscous damping beyond what the single-wave approximation would predict. Here, numerical solutions are obtained for modes of a cylindrical plasma column with rounded ends. Exploiting the fact that the modes of a spheroidal plasma are known analytically (the Dubin modes), a perturbation analysis is used to investigate the mixing of low-order, nearly degenerate Dubin modes caused by small deformations of a plasma spheroid.

Time resolved FTIR study of the catalytic CO oxidation under periodic variation of the reactant concentration

Energy Technology Data Exchange (ETDEWEB)

Kritzenberger, J; Wokaun, A [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

1997-06-01

Oxidation of CO over palladium/zirconia catalyst obtained from an amorphous Pd{sub 25}Zr{sub 75} precursor was investigated by time resolved FTIR spectroscopy. Sine wave shaped modulation of the reactant concentration, i.e. variation of CO or O{sub 2} partial pressure, was used to induce variations of the IR signals of product (CO{sub 2}) and unconverted reactant (CO), which were detected in a multi-pass absorption cell. The phase shift {phi} between external perturbation and variation of the CO{sub 2} signal was examined in dependence on temperature (100{sup o}C{<=}T{<=}350{sup o}C) and modulation frequency (1.39x10{sup -4}Hz{<=}{omega}{<=}6.67x10{sup -2}Hz). From the phase shift values, a simple Eley-Rideal mechanism is excluded, and the rate limiting step of the Langmuir-Hinshelwood mechanism for the CO oxidation may be identified. Adsorption and possible surface movement of CO to the actual reaction site determine the rate of the CO oxidation on the palladium/zirconia catalyst used in our study. The introduction of an external perturbation is a first step towards the application of two-dimensional infrared spectroscopy to heterogeneous catalyzed reactions. (author) 3 figs., 4 refs.

Kinetic of formation for single carbon dioxide and mixed carbon dioxide and tetrahydrofuran hydrates in water and sodium chloride aqueous solution

NARCIS (Netherlands)

Sabil, K.M.; Duarte, A.R.C.; Zevenbergen, J.F.; Ahmad, M.M.; Yusup, S.; Omar, A.A.; Peters, C.J.

2010-01-01

A laboratory-scale reactor system is built and operated to measure the kinetic of formation for single and mixed carbon dioxide-tetrahydrofuran hydrates. The T-cycle method, which is used to collect the kinetic data, is briefly discussed. For single carbon dioxide hydrate, the induction time

General theory of the multistage geminate reactions of the isolated pairs of reactants. II. Detailed balance and universal asymptotes of kinetics.

Science.gov (United States)

Kipriyanov, Alexey A; Doktorov, Alexander B

2014-10-14

The analysis of general (matrix) kinetic equations for the mean survival probabilities of any of the species in a sample (or mean concentrations) has been made for a wide class of the multistage geminate reactions of the isolated pairs. These kinetic equations (obtained in the frame of the kinetic approach based on the concept of "effective" particles in Paper I) take into account various possible elementary reactions (stages of a multistage reaction) excluding monomolecular, but including physical and chemical processes of the change in internal quantum states carried out with the isolated pairs of reactants (or isolated reactants). The general basic principles of total and detailed balance have been established. The behavior of the reacting system has been considered on macroscopic time scales, and the universal long-term kinetics has been determined.

Sub-ensemble monitoring of DNA strand displacement using multiparameter single-molecule FRET

OpenAIRE

Baltierra Jasso, Laura; Morten, Michael; Magennis, Steven William

2018-01-01

Non-enzymatic DNA strand displacement is an important mechanism in dynamic DNA nanotechnology. Here we show that the large parameter space that is accessible by single-molecule FRET is ideal for the simultaneous monitoring of multiple reactants and products of DNA strand exchange reactions. We monitored the strand displacement from double-stranded DNA (dsDNA) by single-stranded DNA (ssDNA) at 37 °C; the data were modelled as a second-order reaction approaching equilibrium, with a rate constan...

Prediction of the single-phase turbulent mixing rate between two parallel subchannels using a subchannel geometry factor

International Nuclear Information System (INIS)

Sadatomi, M.; Kawahara, A.; Sato, Y.

1996-01-01

This paper presents a simple method for predicting the single-phase turbulent mixing rate between adjacent subchannels in nuclear fuel bundles. In this method, the mixing rate is computed as the sum of the two components of turbulent diffusion and convective transfer. Of these, the turbulent diffusion component is calculated using a newly defined subchannel geometry factor F* and the mean turbulent diffusivity for each subchannel which is computed from Elder's equation. The convective transfer component is evaluated from a mixing Stanton number correlation obtained empirically in this study. In order to confirm the validity of the proposed method, experimental data on turbulent mixing rate were obtained using a tracer technique under adiabatic conditions with three test channels, each consisting of two subchannels. The range of Reynolds number covered was 5000-66 000. From comparisons of the predicted turbulent mixing rates with the experimental data of other investigators as well as the authors, it has been confirmed that the proposed method can predict the data in a range of gap clearance to rod diameter ratio of 0.02-0.4 within about ±25% for square array bundles and about ±35% for triangular array bundles. (orig.)

Solid-state photoelectrochemical H2 generation with gaseous reactants

International Nuclear Information System (INIS)

Iwu, Kingsley O.; Galeckas, Augustinas; Kuznetsov, Andrej Yu.; Norby, Truls

2013-01-01

Photocurrent and H 2 production were demonstrated in an all solid-state photoelectrochemical cell employing gaseous methanol and water vapour at the photoanode. Open circuit photovoltage of around −0.4 V and short circuit photocurrent of up to 250 μA/cm 2 were obtained. At positive bias, photocurrent generation was limited by the irradiance, i.e., the amount of photogenerated charge carriers at the anode. Time constants and impedance spectra showed an electrochemical capacitance of the cell of about 15 μF/cm 2 in the dark, which increased with increasing irradiance. With only water vapour at the anode, the short circuit photocurrent was about 6% of the value with gaseous methanol and water vapour. The photoanode and electrocatalyst on carbon paper support were affixed to the proton conducting membrane using Nafion ® as adhesive, an approach that yielded photocurrents up to 15 times better than that of a cell assembled by hot-pressing, in spite of the overall cell resistance of the latter being up to five times less than that of the former. This is attributed, at least partially, to reactants being more readily available at the photoanode of the better performing cell

Spectrally pure heralded single photons by spontaneous four-wave mixing in a fiber: reducing impact of dispersion fluctuations

DEFF Research Database (Denmark)

Koefoed, Jacob Gade; Friis, Søren Michael Mørk; Christensen, Jesper Bjerge

2017-01-01

We model the spectral quantum-mechanical purity of heralded single photons from a photon-pair source based on nondegenerate spontaneous four-wave mixing taking the impact of distributed dispersion fluctuations into account. The considered photon-pair-generation scheme utilizes pump-pulse walk...

Assessing the concordance between child reports and adult observations of single and mixed emotion in children’s drawings of themselves or another child

OpenAIRE

Burkitt, Esther

2017-01-01

The present study assessed concordance between child reported and adult observed strategies to depict single and mixed emotion in the same human figure drawings. 205 children (104 boys, 101 girls) aged 6 years 2 months to 8 year 3 months formed two age groups (6 yrs. 2 mo. - 7 yrs.2 mo. and 7 yrs.-3 mo. -8 yrs. - 3 mo.) across two conditions drawing either themselves or another child. They heard vignettes designed to elicit single and mixed emotion and drew a baseline drawing, counterbalanced...

Effect of reactant concentration on the structural properties of hydrothermally-grown ZnO rods on seed-layer ZnO / polyethylene terephthalate substrates

Energy Technology Data Exchange (ETDEWEB)

Jeong, Y. I.; Shin, C. M.; Heo, J. H.; Ryu, H. [Inje University, Gimhae (Korea, Republic of); Lee, W. J. [Dong-Eui University, Busan (Korea, Republic of); Son, C. S. [Silla University, Busan (Korea, Republic of); Choi, H. [Pukyong National University, Busan (Korea, Republic of)

2011-09-15

The morphology and the structural properties were studied for zinc-oxide (ZnO) rods hydrothermally grown on seed-layer ZnO/polyethylene terephthalate (PET) substrates at various reactant concentrations. Dissolved solutions with de-ionized water, zinc nitrate hexahydrate (Zn(NO{sub 3}){sub 2}{center_dot}6H{sub 2}O, ZNH) and hexamethylenetetramine (C{sub 6}H{sub 12}N{sub 4}, HMT) were employed as reactants for hydrothermal growth of ZnO. The transparency of the mixtures (ZNH+HMT) with increasing reactant concentration from 0.025 to 0.25 M changed from transparent to translucent to opaque (white colors) due to Zn(OH){sub 2} precipitates. When the concentration was increased, the density of the ZnO rods increased, and the morphology of the ZnO rods changed from a hexagonal flat-end shape to a sharp-end or flake-like structure. The sharp-end rods with increasing concentration from 0.1 to 0.15 M resulted from the etching process at a lower pH condition (less than pH 6) after the ZnO rod growth, and the flake-like structure was due to a high growth rate. The ZnO seed layer might have improved the alignment of ZnO rods and made a high density of ZnO rods. In addition, the structural properties were improved at lower concentrations by inserting a seed layer.

Journal of Chemical Sciences | Indian Academy of Sciences

Indian Academy of Sciences (India)

Excited state intramolecular charge transfer reaction of 4-(morpholenyl) benzonitrile in solution: Effects ... in (mixed solvent + electrolyte) systems: Role of reactant-solvent and reactant-ion interactions .... A molecular dynamics simulation study.

Evaluation of Fermentative Hydrogen Production from Single and Mixed Fruit Wastes

Directory of Open Access Journals (Sweden)

Julius Akinbomi

2015-05-01

Full Text Available The economic viability of employing dark fermentative hydrogen from whole fruit wastes as a green alternative to fossil fuels is limited by low hydrogen yield due to the inhibitory effect of some metabolites in the fermentation medium. In exploring means of increasing hydrogen production from fruit wastes, including orange, apple, banana, grape and melon, the present study assessed the hydrogen production potential of singly-fermented fruits as compared to the fermentation of mixed fruits. The fruit feedstock was subjected to varying hydraulic retention times (HRTs in a continuous fermentation process at 55 °C for 47 days. The weight distributions of the first, second and third fruit mixtures were 70%, 50% and 20% orange share, respectively, while the residual weight was shared equally by the other fruits. The results indicated that there was an improvement in cumulative hydrogen yield from all of the feedstock when the HRT was five days. Based on the results obtained, apple as a single fruit and a fruit mixture with 20% orange share have the most improved cumulative hydrogen yields of 504 (29.5% of theoretical yield and 513 mL/g volatile solid (VS (30% of theoretical yield , respectively, when compared to other fruits.

Low-sensitivity, low-bounce, high-linearity current-controlled oscillator suitable for single-supply mixed-mode instrumentation system.

Science.gov (United States)

Hwang, Yuh-Shyan; Kung, Che-Min; Lin, Ho-Cheng; Chen, Jiann-Jong

2009-02-01

A low-sensitivity, low-bounce, high-linearity current-controlled oscillator (CCO) suitable for a single-supply mixed-mode instrumentation system is designed and proposed in this paper. The designed CCO can be operated at low voltage (2 V). The power bounce and ground bounce generated by this CCO is less than 7 mVpp when the power-line parasitic inductance is increased to 100 nH to demonstrate the effect of power bounce and ground bounce. The power supply noise caused by the proposed CCO is less than 0.35% in reference to the 2 V supply voltage. The average conversion ratio KCCO is equal to 123.5 GHz/A. The linearity of conversion ratio is high and its tolerance is within +/-1.2%. The sensitivity of the proposed CCO is nearly independent of the power supply voltage, which is less than a conventional current-starved oscillator. The performance of the proposed CCO has been compared with the current-starved oscillator. It is shown that the proposed CCO is suitable for single-supply mixed-mode instrumentation systems.

The effects of reactants ratios, reaction temperatures and times on Maillard reaction products of the L-ascorbic acid/L-glutamic acid system

Directory of Open Access Journals (Sweden)

Yong-Yan ZHOU

2016-01-01

Full Text Available Abstract The transformation law of the Maillard reaction products with three different reactants ratios - equimolar reactants, excess L-glutamic acid and excess L-ascorbic acid reaction respectively, five different temperatures, and different time conditions for the L-ascorbic acid / L-glutamic acid system were investigated. Results showed that, the increase of the reaction time and temperature led to the increase of the browning products, uncoloured intermediate products, as well as aroma compounds. Compared with the equimolar reaction system, the excess L-ascorbic acid reaction system produced more browning products and uncoloured intermediate products, while the aroma compounds production remained the same. In the excess L-glutamic acid system, the uncoloured intermediate products increased slightly, the browning products remained the same, while the aroma compounds increased.

Flame stabilization and mixing characteristics in a Stagnation Point Reverse Flow combustor

Science.gov (United States)

Bobba, Mohan K.

A novel combustor design, referred to as the Stagnation Point Reverse-Flow (SPRF) combustor, was recently developed that is able to operate stably at very lean fuel-air mixtures and with low NOx emissions even when the fuel and air are not premixed before entering the combustor. The primary objective of this work is to elucidate the underlying physics behind the excellent stability and emissions performance of the SPRF combustor. The approach is to experimentally characterize velocities, species mixing, heat release and flame structure in an atmospheric pressure SPRF combustor with the help of various optical diagnostic techniques: OH PLIF, chemiluminescence imaging, PIV and Spontaneous Raman Scattering. Results indicate that the combustor is primarily stabilized in a region downstream of the injector that is characterized by low average velocities and high turbulence levels; this is also the region where most of the heat release occurs. High turbulence levels in the shear layer lead to increased product entrainment levels, elevating the reaction rates and thereby enhancing the combustor stability. The effect of product entrainment on chemical timescales and the flame structure is illustrated with simple reactor models. Although reactants are found to burn in a highly preheated (1300 K) and turbulent environment due to mixing with hot product gases, the residence times are sufficiently long compared to the ignition timescales such that the reactants do not autoignite. Turbulent flame structure analysis indicates that the flame is primarily in the thin reaction zones regime throughout the combustor, and it tends to become more flamelet like with increasing distance from the injector. Fuel-air mixing measurements in case of non-premixed operation indicate that the fuel is shielded from hot products until it is fully mixed with air, providing nearly premixed performance without the safety issues associated with premixing. The reduction in NOx emissions in the SPRF

Mixed methods research.

Science.gov (United States)

Halcomb, Elizabeth; Hickman, Louise

2015-04-08

Mixed methods research involves the use of qualitative and quantitative data in a single research project. It represents an alternative methodological approach, combining qualitative and quantitative research approaches, which enables nurse researchers to explore complex phenomena in detail. This article provides a practical overview of mixed methods research and its application in nursing, to guide the novice researcher considering a mixed methods research project.

Mixing ratio sensor of alcohol mixed fuel

Energy Technology Data Exchange (ETDEWEB)

Miyata, Shigeru; Matsubara, Yoshihiro

1987-08-07

In order to improve combustion efficiency of an internal combustion engine using gasoline-alcohol mixed fuel and to reduce harmful substance in its exhaust gas, it is necessary to control strictly the air-fuel ratio to be supplied and the ignition timing and change the condition of control depending upon the mixing ratio of the mixed fuel. In order to detect the mixing ratio of the mixed fuel, the above mixing ratio has so far been detected by casting a ray of light to the mixed fuel and utilizing a change of critical angle associated with the change of the composition of the fluid of the mixed fuel. However, in case when a light emitting diode is used for the light source above, two kinds of sensors are further needed. Concerning the two kinds of sensors above, this invention offers a mixing ratio sensor for the alcohol mixed fuel which can abolish a temperature sensor to detect the environmental temperature by making a single compensatory light receiving element deal with the compensation of the amount of light emission of the light emitting element due to the temperature change and the compensation of the critical angle caused by the temperature change. (6 figs)

GPS data processing of networks with mixed single- and dual-frequency receivers for deformation monitoring

Science.gov (United States)

Zou, X.; Deng, Z.; Ge, M.; Dick, G.; Jiang, W.; Liu, J.

2010-07-01

In order to obtain crustal deformations of higher spatial resolution, existing GPS networks must be densified. This densification can be carried out using single-frequency receivers at moderate costs. However, ionospheric delay handling is required in the data processing. We adapt the Satellite-specific Epoch-differenced Ionospheric Delay model (SEID) for GPS networks with mixed single- and dual-frequency receivers. The SEID model is modified to utilize the observations from the three nearest dual-frequency reference stations in order to avoid contaminations from more remote stations. As data of only three stations are used, an efficient missing data constructing approach with polynomial fitting is implemented to minimize data losses. Data from large scale reference networks extended with single-frequency receivers can now be processed, based on the adapted SEID model. A new data processing scheme is developed in order to make use of existing GPS data processing software packages without any modifications. This processing scheme is evaluated using a sub-network of the German SAPOS network. The results verify that the new scheme provides an efficient way to densify existing GPS networks with single-frequency receivers.

SHS synthesis of Si-SiC composite powders using Mg and reactants from industrial waste

Science.gov (United States)

Chanadee, Tawat

2017-11-01

Si-SiC composite powders were synthesized by self-propagating high-temperature synthesis (SHS) using reactants of fly ash-based silica, sawdust-based activated carbon, and magnesium. Fly ash-based silica and sawdust-based activated carbon were prepared from coal mining fly ash and Para rubber-wood sawdust, respectively. The work investigated the effects of the synthesis atmosphere (air and Ar) on the phase and morphology of the SHS products. The SHS product was leached by a two-step acid leaching processes, to obtain the Si-SiC composite powder. The SHS product and SHS product after leaching were characterized by X-ray diffractometry, scanning electron microscopy and energy dispersive X-ray spectrometry. The results indicated that the SHS product synthesized in air consisted of Si, SiC, MgO, and intermediate phases (SiO2, Mg, Mg2SiO4, Mg2Si), whereas the SHS product synthesized in Ar consisted of Si, SiC, MgO and a little Mg2SiO4. The SiC content in the leached-SHS product was higher when Ar was used as the synthesis atmosphere. As well as affecting the purity, the synthesis atmospheres also affected the average crystalline sizes of the products. The crystalline size of the product synthesized in Ar was smaller than that of the product synthesized in air. All of the results showed that fly ash and sawdust could be effective waste-material reactants for the synthesis of Si-SiC composite powders.

Temperature-dependent ion beam mixing

International Nuclear Information System (INIS)

Rehn, L.E.; Alexander, D.E.

1993-08-01

Recent work on enhanced interdiffusion rates during ion-beam mixing at elevated temperatures is reviewed. As discussed previously, expected increase in ion-beam mixing rates due to 'radiation-enhanced diffusion' (RED), i.e. the free migration of isolated vacancy and interstitial defects, is well documented in single-crystal specimens in the range of 0.4 to 0.6 of absolute melting temperature. In contrast, the increase often observed at somewhat lower temperatures during ion-beam mixing of polycrystalline specimens is not well understood. However, sufficient evidence is available to show that this increase reflects intracascade enhancement of a thermally-activated process that also occurs without irradiation. Recent evidence is presented which suggests that this process is Diffusion-induced Grain-Boundary Migration (DIGM). An important complementary conclusion is that because ion-beam mixing in single-crystal specimens exhibits no significant temperature dependence below that of RED, models that invoke only irradiation-specific phenomena, e.g., cascade-overlap, thermal-spikes, or liquid-diffusion, and hence which predict no difference in mixing behavior between single- or poly-crystalline specimens, cannot account for the existing results

Degenerate mixing of plasma waves on cold, magnetized single-species plasmas

International Nuclear Information System (INIS)

Anderson, M. W.; O'Neil, T. M.; Dubin, D. H. E.; Gould, R. W.

2011-01-01

In the cold-fluid dispersion relation ω=ω p /[1+(k perpendicular /k z ) 2 ] 1/2 for Trivelpiece-Gould waves on an infinitely long magnetized plasma cylinder, the transverse and axial wavenumbers appear only in the combination k perpendicular /k z . As a result, for any frequency ω p , there are infinitely many degenerate waves, all having the same value of k perpendicular /k z . On a cold finite-length plasma column, these degenerate waves reflect into one another at the ends; thus, each standing-wave normal mode of the bounded plasma is a mixture of many degenerate waves, not a single standing wave as is often assumed. A striking feature of the many-wave modes is that the short-wavelength waves often add constructively along resonance cones given by dz/dr=±(ω p 2 /ω 2 -1) 1/2 . Also, the presence of short wavelengths in the admixture for a predominantly long-wavelength mode enhances the viscous damping beyond what the single-wave approximation would predict. Here, numerical solutions are obtained for modes of a cylindrical plasma column with rounded ends. Exploiting the fact that the modes of a spheroidal plasma are known analytically (the Dubin modes), a perturbation analysis is used to investigate the mixing of low-order, nearly degenerate Dubin modes caused by small deformations of a plasma spheroid.

CATALYST-FREE REACTIONS UNDER SOLVENT-FEE CONDITIONS: MICROWAVE-ASSISTED SYNTHESIS OF HETEROCYCLIC HYDRAZONES BELOW THE MELTING POINT OF NEAT REACTANTS: JOURNAL ARTICLE

Science.gov (United States)

NRMRL-CIN-1437 Jeselnik, M., Varma*, R.S., Polanc, S., and Kocevar, M. Catalyst-free Reactions under Solvent-fee Conditions: Microwave-assisted Synthesis of Heterocyclic Hydrazones below the Melting Point of Neat Reactants. Published in: Chemical Communications 18:1716-1717 (200...

Selectivity of single, mixed, and modified pseudostationary phases in electrokinetic chromatography.

Science.gov (United States)

Fuguet, Elisabet; Ràfols, Clara; Bosch, Elisabeth; Abraham, Michael H; Rosés, Martí

2006-05-01

The selectivity of a compilation of single, mixed, and modified EKC pseudostationary phases, described in the literature and characterized through the solvation parameter model, is analyzed. Not only have micellar systems of different nature been included but also microemulsions, polymeric, and liposomial phases. In order to compare the systems, a principal component analysis of the coefficients of the solvation equation is performed. From this analysis, direct information of the system properties, differences in selectivity, as well as evidence of lack of accuracy in some system characterizations are obtained. These results become a very useful tool to perform separations with mixtures of surfactants, since it is possible to know which mixtures will provide a greater selectivity variation by changing only the composition of the pseudostationary phases. Furthermore, the variation of the selectivity of some mixtures, as well as the effect of the addition of organic solvents on selectivity, is also discussed.

One size fits all? Mixed methods evaluation of the impact of 100% single-room accommodation on staff and patient experience, safety and costs

Science.gov (United States)

Maben, Jill; Penfold, Clarissa; Simon, Michael; Anderson, Janet E; Robert, Glenn; Pizzo, Elena; Hughes, Jane; Murrells, Trevor; Barlow, James

2016-01-01

Background and objectives There is little strong evidence relating to the impact of single-room accommodation on healthcare quality and safety. We explore the impact of all single rooms on staff and patient experience; safety outcomes; and costs. Methods Mixed methods pre/post ‘move’ comparison within four nested case study wards in a single acute hospital with 100% single rooms; quasi-experimental before-and-after study with two control hospitals; analysis of capital and operational costs associated with single rooms. Results Two-thirds of patients expressed a preference for single rooms with comfort and control outweighing any disadvantages (sense of isolation) felt by some. Patients appreciated privacy, confidentiality and flexibility for visitors afforded by single rooms. Staff perceived improvements (patient comfort and confidentiality), but single rooms were worse for visibility, surveillance, teamwork, monitoring and keeping patients safe. Staff walking distances increased significantly post move. A temporary increase of falls and medication errors in one ward was likely to be associated with the need to adjust work patterns rather than associated with single rooms per se. We found no evidence that single rooms reduced infection rates. Building an all single-room hospital can cost 5% more with higher housekeeping and cleaning costs but the difference is marginal over time. Conclusions Staff needed to adapt their working practices significantly and felt unprepared for new ways of working with potentially significant implications for the nature of teamwork in the longer term. Staff preference remained for a mix of single rooms and bays. Patients preferred single rooms. PMID:26408568

Ultrafast Single-Shot Optical Oscilloscope based on Time-to-Space Conversion due to Temporal and Spatial Walk-Off Effects in Nonlinear Mixing Crystal

Science.gov (United States)

Takagi, Yoshihiro; Yamada, Yoshifumi; Ishikawa, Kiyoshi; Shimizu, Seiji; Sakabe, Shuji

2005-09-01

A simple method for single-shot sub-picosecond optical pulse diagnostics has been demonstrated by imaging the time evolution of the optical mixing onto the beam cross section of the sum-frequency wave when the interrogating pulse passes over the tested pulse in the mixing crystal as a result of the combined effect of group-velocity difference and walk-off beam propagation. A high linearity of the time-to-space projection is deduced from the process solely dependent upon the spatial uniformity of the refractive indices. A snap profile of the accidental coincidence between asynchronous pulses from separate mode-locked lasers has been detected, which demonstrates the single-shot ability.

Mixing state of particles with secondary species by single particle aerosol mass spectrometer in an atmospheric pollution event

Science.gov (United States)

Xu, Lingling; Chen, Jinsheng

2016-04-01

Single particle aerosol mass spectrometer (SPAMS) was used to characterize size distribution, chemical composition, and mixing state of particles in an atmospheric pollution event during 20 Oct. - 5 Nov., 2015 in Xiamen, Southeast China. A total of 533,012 particle mass spectra were obtained and clustered into six groups, comprising of industry metal (4.5%), dust particles (2.6%), carbonaceous species (70.7%), K-Rich particles (20.7%), seasalt (0.6%) and other particles (0.9%). Carbonaceous species were further divided into EC (70.6%), OC (28.5%), and mixed ECOC (0.9%). There were 61.7%, 58.3%, 4.0%, and 14.6% of particles internally mixed with sulfate, nitrate, ammonium and C2H3O, respectively, indicating that these particles had undergone significant aging processing. Sulfate was preferentially mixed with carbonaceous particles, while nitrate tended to mix with metal-containing and dust particles. Compared to clear days, the fractions of EC-, metal- and dust particles remarkably increased, while the fraction of OC-containing particles decreased in pollution days. The mixing state of particles, excepted for OC-containing particles with secondary species was much stronger in pollution days than that in clear days, which revealed the significant influence of secondary particles in atmospheric pollution. The different activity of OC-containing particles might be related to their much smaller aerodynamic diameter. These results could improve our understanding of aerosol characteristics and could be helpful to further investigate the atmospheric process of particles.

Reversible Single-Crystal-to-Single-Crystal Structural Transformation in a Mixed-Ligand 2D Layered Metal-Organic Framework: Structural Characterization and Sorption Study

Directory of Open Access Journals (Sweden)

Chih-Chieh Wang

2017-12-01

Full Text Available A 3D supramolecular network, [Cd(bipy(C4O4(H2O2]·3H2O (1 (bipy = 4,4′-bipyridine and C4O42− = dianion of H2C4O4, constructed by mixed-ligand two-dimensional (2D metal-organic frameworks (MOFs has been reported and structurally determined by the single-crystal X-ray diffraction method and characterized by other physicochemical methods. In 1, the C4O42− and bipy both act as bridging ligands connecting the Cd(II ions to form a 2D layered MOF, which are then extended to a 3D supramolecular network via the mutually parallel and interpenetrating arrangements among the 2D-layered MOFs. Compound 1 shows a two-step dehydration process with weight losses of 11.0% and 7.3%, corresponding to the weight-loss of three guest and two coordinated water molecules, respectively, and exhibits an interesting reversible single-crystal-to-single-crystal (SCSC structural transformation upon de-hydration and re-hydration for guest water molecules. The SCSC structural transformation have been demonstrated and monitored by single-crystal and X-ray powder diffraction, and thermogravimetic analysis studies.

Modelling and simulation of a direct ethanol fuel cell considering multistep electrochemical reactions, transport processes and mixed potentials

International Nuclear Information System (INIS)

Meyer, Marco; Melke, Julia; Gerteisen, Dietmar

2011-01-01

Highlights: → A DEFC model considering the mixed potential formation at cathode and anode. → The low cell voltage at open circuit is due to the parasitic reaction of ethanol and oxygen. → Under load, only the parasitic oxidation of ethanol is significant. → Inhibiting the parasitic reactions can approximately double the current density. - Abstract: In this work a one-dimensional mathematical model of a direct ethanol fuel cell (DEFC) is presented. The electrochemical oxidation of ethanol in the catalyst layers is described by several reaction steps leading to surface coverage with adsorbed intermediates (CH 3 CO, CO, CH 3 and OH) and to the final products acetaldehyde, acetic acid and CO 2 . A bifunctional reaction mechanism is assumed for the activation of water on a binary catalyst favouring the further oxidation of adsorbates blocking active catalyst sites. The chemical reactions are highly coupled with the charge and reactant transport. The model accounts for crossover of the reactants through the membrane leading to the phenomenon of cathode and anode mixed potentials due to the parasitic oxidation and reduction of ethanol and oxygen, respectively. Polarisation curves of a DEFC were recorded for various ethanol feed concentrations and were used as reference data for the simulation. Based on one set of model parameters the characteristic of electronic and protonic potential, the relative surface coverage and the parasitic current densities in the catalyst layers were studied.

Redox flow batteries with serpentine flow fields: Distributions of electrolyte flow reactant penetration into the porous carbon electrodes and effects on performance

Science.gov (United States)

Ke, Xinyou; Prahl, Joseph M.; Alexander, J. Iwan D.; Savinell, Robert F.

2018-04-01

Redox flow batteries with flow field designs have been demonstrated to boost their capacities to deliver high current density and power density in medium and large-scale energy storage applications. Nevertheless, the fundamental mechanisms involved with improved current density in flow batteries with serpentine flow field designs have been not fully understood. Here we report a three-dimensional model of a serpentine flow field over a porous carbon electrode to examine the distributions of pressure driven electrolyte flow penetrations into the porous carbon electrodes. We also estimate the maximum current densities associated with stoichiometric availability of electrolyte reactant flow penetrations through the porous carbon electrodes. The results predict reasonably well observed experimental data without using any adjustable parameters. This fundamental work on electrolyte flow distributions of limiting reactant availability will contribute to a better understanding of limits on electrochemical performance in flow batteries with serpentine flow field designs and should be helpful to optimizing flow batteries.

TA Treatment of Depression - A Hermeneutic Single-Case Efficacy Design Study - ‘Linda’ - a mixed outcome case

Directory of Open Access Journals (Sweden)

Mark Widdowson

2013-07-01

Full Text Available Hermeneutic Single-Case EfficacyDesign (HSCED is a systematic case study research method involving the cross-examination of mixed method data to generate both plausible arguments that the client changed due to therapy and alternative explanations. The present study is the fourth article of a case series which has investigated the process and outcome of transactional analysis psychotherapy using Hermeneutic Single-Case Efficacy Design (Elliott 2002. The client, Linda, was a 45 yearold white British woman with mild depression who attended nine sessions of therapy. The conclusion of the judges was that this was a mixed-outcome case:whilst the client improved over the course of therapy and was positive about her experience of therapy, her changes did not last when she experienced considerable stressful events during follow-up. Linda provided a detailed and idiosyncratic description of the aspects of the therapy which were most helpful for her. A cross-case comparison with other cases in this series suggests several interesting features which are worthy of further investigation. Specifically, the use of a shared theoretical framework and an egalitarian therapeutic relationship were helpful. As with other cases in this series, the client experienced positive changes in her interpersonal relationships suggesting that this outcome of TA therapy warrants further investigation

Double-strand breaks in genome-sized DNA caused by mechanical stress under mixing: Quantitative evaluation through single-molecule observation

Science.gov (United States)

Kikuchi, Hayato; Nose, Keiji; Yoshikawa, Yuko; Yoshikawa, Kenichi

2018-06-01

It is becoming increasingly apparent that changes in the higher-order structure of genome-sized DNA molecules of more than several tens kbp play important roles in the self-control of genome activity in living cells. Unfortunately, it has been rather difficult to prepare genome-sized DNA molecules without damage or fragmentation. Here, we evaluated the degree of double-strand breaks (DSBs) caused by mechanical mixing by single-molecule observation with fluorescence microscopy. The results show that DNA breaks are most significant for the first second after the initiation of mechanical agitation. Based on such observation, we propose a novel mixing procedure to significantly decrease DSBs.

Replacing Chlorine with Hydrogen Chloride as a Possible Reactant for Synthesis of Titanium Carbide Derived Carbon Powders for High-Technology Devices

International Nuclear Information System (INIS)

Tallo, Indrek; Thomberg, Thomas; Jänes, Alar; Lust, Enn

2013-01-01

Micro- and mesoporous carbide-derived carbons were synthesized from titanium carbide (TiC) powder via gas phase reaction by using different reactants (Cl 2 and HCl) within the temperature range from 700 to 1100 °C. Analysis of XRD results show that TiC-derived carbons (TiC-CDC) consist mainly of graphitic crystallites. The first-order Raman spectra showed the graphite-like absorption peaks at ∼1577 cm 1 and the disorder-induced peaks at ∼1338 cm- 1 . The energy-related properties of supercapacitors based on 1 M (C 2 H 5 ) 3 CH 3 NBF 4 in acetonitrile and carbide-derived carbons (TiC-CDC (Cl 2 ) and TiC-CDC (HCl)) as electrode materials were also investigated using cyclic voltammetry, electrochemical impedance spectroscopy, galvanostatic charge/discharge and constant power methods. The Ragone plots for carbide-derived carbons prepared by using different reactants (Cl 2 , HCl) are quite similar and at high power loads TiC-CDC (Cl 2 ) material synthesized at 900 °C, i.e. materials with optimal porous structure, deliver higher power at constant energy

Depth and Extent of Gas-Ablator Mix in Symcap Implosions at the National Ignition Facility

Science.gov (United States)

Pino, Jesse; Ma, T.; MacLaren, S. A.; Salmonson, J. D.; Ho, D.; Khan, S. F.; Masse, L.; Ralph, J. E.; Czajka, C.; Casey, D.; Sacks, R.; Smalyuk, V. A.; Tipton, R. E.; Kyrala, G. A.

2017-10-01

A longstanding question in ICF physics has been the extent to which capsule ablator material mixes into the burning fusion fuel and degrades performance. Several recent campaigns at the National Ignition Facility have examined this question through the use of separated reactants. A layer of CD plastic is placed on the inner surface of the CH shell and the shell is filled with a gas mixture of H and T. This allows for simultaneous neutron signals that inform different aspects of the physics; we get core TT neutron yield, atomic mix from the DT neutrons, and information about shell heating from the DD neutron signal. By systematically recessing the CD layer away from the gas boundary we gain an inference of the depth of the mixing layer. This presentation will cover three campaigns to look at mixing depth: An ignition-like design (``Low-foot'') at two convergence ratios, as well as a robust, nearly one-dimensional, low convergence, symmetric platform designed to minimize ablation front feed-through (HED 2-shock). We show that the 2-shock capsule has less ablator-gas mix, and compare the experimental results to mix-model simulations. This work was performed under the auspices of the U.S. Department of Energy by LLNL under Contract DE-AC52-07NA27344, LLNS, LLC.

Direct single-molecule dynamic detection of chemical reactions.

Science.gov (United States)

Guan, Jianxin; Jia, Chuancheng; Li, Yanwei; Liu, Zitong; Wang, Jinying; Yang, Zhongyue; Gu, Chunhui; Su, Dingkai; Houk, Kendall N; Zhang, Deqing; Guo, Xuefeng

2018-02-01

Single-molecule detection can reveal time trajectories and reaction pathways of individual intermediates/transition states in chemical reactions and biological processes, which is of fundamental importance to elucidate their intrinsic mechanisms. We present a reliable, label-free single-molecule approach that allows us to directly explore the dynamic process of basic chemical reactions at the single-event level by using stable graphene-molecule single-molecule junctions. These junctions are constructed by covalently connecting a single molecule with a 9-fluorenone center to nanogapped graphene electrodes. For the first time, real-time single-molecule electrical measurements unambiguously show reproducible large-amplitude two-level fluctuations that are highly dependent on solvent environments in a nucleophilic addition reaction of hydroxylamine to a carbonyl group. Both theoretical simulations and ensemble experiments prove that this observation originates from the reversible transition between the reactant and a new intermediate state within a time scale of a few microseconds. These investigations open up a new route that is able to be immediately applied to probe fast single-molecule physics or biophysics with high time resolution, making an important contribution to broad fields beyond reaction chemistry.

Flapping model of scalar mixing in turbulence

International Nuclear Information System (INIS)

Kerstein, A.R.

1991-01-01

Motivated by the fluctuating plume model of turbulent mixing downstream of a point source, a flapping model is formulated for application to other configurations. For the scalar mixing layer, simple expressions for single-point scalar fluctuation statistics are obtained that agree with measurements. For a spatially homogeneous scalar mixing field, the family of probability density functions previously derived using mapping closure is reproduced. It is inferred that single-point scalar statistics may depend primarily on large-scale flapping motions in many cases of interest, and thus that multipoint statistics may be the principal indicators of finer-scale mixing effects

Rhizospheric salt tolerant bacteria improving plant growth in single and mixed culture inoculations under NaCl stress (abstract)

International Nuclear Information System (INIS)

Afrasayab, S.; Hasnain, S.

2005-01-01

Salt tolerant bacterial strains isolated from rhizosphere of Mazus plant (inhabitant of salt range) were used singly (ST -1; ST -2; ST -3; ST -4) and in mixed combinations (ST -1,3,4; ST -2,3,4) to improve the growth to Tricticum aestivum in the pot experiments. Growth and yield of T. aestivum var. Inqlab-91 plants exposed to NaCl stress (0.75% NaCl) was markedly affected. Na/sup +//K/sup +/ ratios in shoots and roots were profoundly increased under NaCl stress. Bacterial inoculations improved plant growth under salt stress. Bacterial combinations ST - 1,3,4 and ST -2,3,4 were more effective in stimulating growth and showed prominent results as compared to their pure cultures. Mono and mixed bacterial inoculations improved yield parameters of wheat. ST -1,3,4 mixed culture inoculation maximally improved yield under salt stress. Generally bacterial inoculations resulted in increase in Na/sup +//K/sup +/ ratios in shoots and roots under salt free and salt stress conditions. Overall ST -1,3,4 mixed inoculation yielded promising results under NaCl stress, hence 168 rRNA gene sequence analysis of its pure cultures was obtained for their identification to genus level. (author)

Teachers' implementation of gender-inclusive instructional strategies in single-sex and mixed-sex science classrooms

Science.gov (United States)

Parker, Lesley H.; Rennie, Léonie J.

2002-09-01

Debate continues over the benefits, or otherwise, of single-sex classes in science and mathematics, particularly for the performance of girls. Previous research and analyses of the circumstances surrounding the implementation of single-sex classes warn that the success of the strategy requires due consideration of the nature of the instructional environment for both boys and girls, together with appropriate support for the teachers involved. This article reports the circumstances under which teachers were able to implement gender-inclusive strategies in single-sex science classes in coeducational high schools and documents some of the difficulties faced. The study was part of the Single-Sex Education Pilot Project (SSEPP) in ten high schools in rural and urban Western Australia. Qualitative and quantitative data were gathered during the project from teachers, students and classroom observations. Overall, it was apparent that single-sex grouping created environments in which teachers could implement gender-inclusive science instructional strategies more readily and effectively than in mixed-sex settings. Teachers were able to address some of the apparent shortcomings of the students' previous education (specifically, the poor written and oral communication of boys and the limited experience of girls with 'hands-on' activities and open-ended problem solving). Further, in same-sex classrooms, sexual harassment which inhibited girls' learning was eliminated. The extent to which teachers were successful in implementing gender-inclusive instructional strategies, however, depended upon their prior commitment to the SSEPP as a whole, and upon the support or obstacles encountered from a variety of sources, including parents, the community, students, and non-SSEPP teachers.

Single-phase cross-mixing measurements in a 4 x 4 rod bundle

International Nuclear Information System (INIS)

Yloenen, Arto; Bissels, Wilhelm-Martin; Prasser, Horst-Michael

2011-01-01

Highlights: → The wire-mesh sensor technique has been successfully introduced into a fuel rod bundle geometry. → Quantitative information on the turbulent dispersion of the fluid was obtained. → In full spatial and temporal resolution, the data is interesting for the unsteady CFD validation. - Abstract: The wire-mesh sensor technique has been successfully introduced into a fuel rod bundle geometry for the first time. In this context, a dedicated test facility (SUBFLOW) has been designed and constructed at Paul Scherrer Institut (PSI) in a co-operation with the Swiss Federal Institute of Technology (ETH Zuerich). Two wire-mesh sensors designed and built in-house were installed in the upper part of the vertical test section of SUBFLOW, and single-phase experiments on the turbulent mass exchange between neighboring sub-channels were performed. For this purpose, salt tracer was injected locally in one of the sub-channels and conductivity distributions in the bundle measured by the wire-mesh sensor. Both flow rate and distance from the injection point were varied. The latter was achieved by using injection nozzles at different heights. In this way, the sensor located in the upper part of the channel could be used to characterize the progress of the mixing along the flow direction, and the degree of cross-mixing assessed using the quantity of tracer arriving in the neighboring sub-channels. Fluctuations of the tracer concentration in time were used for statistical evaluations, such as the calculation of standard deviations and two-point correlations.

Ab Initio Modeling of Structure and Properties of Single and Mixed Alkali Silicate Glasses.

Science.gov (United States)

Baral, Khagendra; Li, Aize; Ching, Wai-Yim

2017-10-12

A density functional theory (DFT)-based ab initio molecular dynamics (AIMD) has been applied to simulate models of single and mixed alkali silicate glasses with two different molar concentrations of alkali oxides. The structural environments and spatial distributions of alkali ions in the 10 simulated models with 20% and 30% of Li, Na, K and equal proportions of Li-Na and Na-K are studied in detail for subtle variations among the models. Quantum mechanical calculations of electronic structures, interatomic bonding, and mechanical and optical properties are carried out for each of the models, and the results are compared with available experimental observation and other simulations. The calculated results are in good agreement with the experimental data. We have used the novel concept of using the total bond order density (TBOD), a quantum mechanical metric, to characterize internal cohesion in these glass models. The mixed alkali effect (MAE) is visible in the bulk mechanical properties but not obvious in other physical properties studied in this paper. We show that Li doping deviates from expected trend due to the much stronger Li-O bonding than those of Na and K doping. The approach used in this study is in contrast with current studies in alkali-doped silicate glasses based only on geometric characterizations.

Kinetics of diffusion-controlled and ballistically-controlled reactions

International Nuclear Information System (INIS)

Redner, S.

1995-01-01

The kinetics of diffusion-controlled two-species annihilation, A+B → O and single-species ballistically-controlled annihilation, A+A → O are investigated. For two-species annihilation, we describe the basic mechanism that leads to the formation of a coarsening mosaic of A- and B-domains. The implications of this picture on the distribution of reactants is discussed. For ballistic annihilation, dimensional analysis shows that the concentration and rms velocity decay as c∼t -α and v∼t -β , respectively, with α+β = 1 in any spatial dimension. Analysis of the Boltzmann equation for the evolution of the velocity distribution yields accurate predictions for the kinetics. New phenomena associated with discrete initial velocity distributions and with mixed ballistic and diffusive reactant motion are also discussed. (author)

Electrical detection and quantification of single and mixed DNA nucleotides in suspension

Science.gov (United States)

Ahmad, Mahmoud Al; Panicker, Neena G.; Rizvi, Tahir A.; Mustafa, Farah

2016-09-01

High speed sequential identification of the building blocks of DNA, (deoxyribonucleotides or nucleotides for short) without labeling or processing in long reads of DNA is the need of the hour. This can be accomplished through exploiting their unique electrical properties. In this study, the four different types of nucleotides that constitute a DNA molecule were suspended in a buffer followed by performing several types of electrical measurements. These electrical parameters were then used to quantify the suspended DNA nucleotides. Thus, we present a purely electrical counting scheme based on the semiconductor theory that allows one to determine the number of nucleotides in a solution by measuring their capacitance-voltage dependency. The nucleotide count was observed to be similar to the multiplication of the corresponding dopant concentration and debye volume after de-embedding the buffer contribution. The presented approach allows for a fast and label-free quantification of single and mixed nucleotides in a solution.

A Chebyshev method for state-to-state reactive scattering using reactant-product decoupling: OH + H2 → H2O + H.

Science.gov (United States)

Cvitaš, Marko T; Althorpe, Stuart C

2013-08-14

We extend a recently developed wave packet method for computing the state-to-state quantum dynamics of AB + CD → ABC + D reactions [M. T. Cvitaš and S. C. Althorpe, J. Phys. Chem. A 113, 4557 (2009)] to include the Chebyshev propagator. The method uses the further partitioned approach to reactant-product decoupling, which uses artificial decoupling potentials to partition the coordinate space of the reaction into separate reactant, product, and transition-state regions. Separate coordinates and basis sets can then be used that are best adapted to each region. We derive improved Chebyshev partitioning formulas which include Mandelshtam-and-Taylor-type decoupling potentials, and which are essential for the non-unitary discrete variable representations that must be used in 4-atom reactive scattering calculations. Numerical tests on the fully dimensional OH + H2 → H2O + H reaction for J = 0 show that the new version of the method is as efficient as the previously developed split-operator version. The advantages of the Chebyshev propagator (most notably the ease of parallelization for J > 0) can now be fully exploited in state-to-state reactive scattering calculations on 4-atom reactions.

A Regime Diagram for Autoignition of Homogeneous Reactant Mixtures with Turbulent Velocity and Temperature Fluctuations

KAUST Repository

Im, Hong G.

2015-04-02

A theoretical scaling analysis is conducted to propose a diagram to predict weak and strong ignition regimes for a compositionally homogeneous reactant mixture with turbulent velocity and temperature fluctuations. The diagram provides guidance on expected ignition behavior based on the thermo-chemical properties of the mixture and the flow/scalar field conditions. The analysis is an extension of the original Zeldovich’s analysis by combining the turbulent flow and scalar characteristics in terms of the characteristic Damköhler and Reynolds numbers of the system, thereby providing unified and comprehensive understanding of the physical and chemical mechanisms controlling ignition characteristics. Estimated parameters for existing experimental measurements in a rapid compression facility show that the regime diagram predicts the observed ignition characteristics with good fidelity.

A Regime Diagram for Autoignition of Homogeneous Reactant Mixtures with Turbulent Velocity and Temperature Fluctuations

KAUST Repository

Im, Hong G.; Pal, Pinaki; Wooldridge, Margaret S.; Mansfield, Andrew B.

2015-01-01

A theoretical scaling analysis is conducted to propose a diagram to predict weak and strong ignition regimes for a compositionally homogeneous reactant mixture with turbulent velocity and temperature fluctuations. The diagram provides guidance on expected ignition behavior based on the thermo-chemical properties of the mixture and the flow/scalar field conditions. The analysis is an extension of the original Zeldovich’s analysis by combining the turbulent flow and scalar characteristics in terms of the characteristic Damköhler and Reynolds numbers of the system, thereby providing unified and comprehensive understanding of the physical and chemical mechanisms controlling ignition characteristics. Estimated parameters for existing experimental measurements in a rapid compression facility show that the regime diagram predicts the observed ignition characteristics with good fidelity.

Writing a Mixed Methods Report in Social Work Research

Science.gov (United States)

Bronstein, Laura R.; Kovacs, Pamela J.

2013-01-01

This article briefly chronicles the development of mixed methods research and its use in social work. We then move onto a discussion of terms and designs, reasons for (and for not) using mixed methods. Drawing upon exemplars, we address how to write up a mixed methods study when (1) the sample is single; single for one part, with a subset for the…

Polymeric Electrolyte Membrane Photoelectrochemical (PEM-PEC Cell with a Web of Titania Nanotube Arrays as Photoanode and Gaseous Reactants

Directory of Open Access Journals (Sweden)

Tsampas M.N.

2017-01-01

Photoanodes of titania nanotube arrays, TNTAs, were developed, for the first time, on a Ti-web of microfiber substrates, by electrochemical anodization. The performance of TNTAs/Ti-web photoanodes were evaluated in both gaseous and liquid reactants. Due to the presence of reliable reference electrode in gas phase direct comparison of the results was possible. Gas phase operation with He or Air as carrier gases and only 2.5% of water content exhibits very promising photoefficiency in comparison with conventional PEC cells.

Influence of Incomplete Mixing on the OH-Isoprene Reaction in the Lower Troposphere - Measurements Above the Amazon Rain Forest and General Considerations

Science.gov (United States)

Sörgel, M.; Dlugi, R. J. W.; Berger, M.; Mallik, C.; Tsokankunku, A.; Zelger, M.; Acevedo, O. C.; Dias, N. L.; Hofzumahaus, A.; Kesselmeier, J.; Kramm, G.; Marno, D. R.; Martinez, M.; Nölscher, A.; H G, O.; Pfannerstill, E.; Bourtsoukidis, E.; Rohrer, F.; Tauer, S.; Williams, J.; Yanez Serrano, A. M.; Andreae, M. O.; Harder, H.

2017-12-01

Incomplete mixing of reactants in the atmosphere (segregation) causes reduced reaction rates compared to laboratory values derived for well mixed conditions. To adequately determine the actual reaction rates in a variety of natural environments where the distribution of sources and sinks leads to inhomogeneous distribution of reactants, the intensity of segregation (IS) has to be taken into account. Although, there has been considerable progress in modeling IS in the boundary layer within the last 30 years, calculations from direct observations are still sparse as high time resolution and time synchronization are required. OH-radicals are the most important oxidizing agent in the atmosphere, and are therefore regarded as the detergent of the atmosphere, reacting with the majority of atmospheric pollutants and therefore accelerating their removal from the atmosphere. Hence, to understand atmospheric self-cleansing, we need to quantify and understand the budgets (sources and sinks) of OH. As it is a fast reacting compound, for some of its reactants mixing will limit the reaction rate. The reaction of isoprene and OH radicals has gained considerable interest in recent years since large discrepancies between modeled and measured OH have been found mainly in high isoprene environments. This motivated not only laboratory studies on unknown recycling mechanisms for OH in this reaction, but also modeling work and field studies on the effect of segregation on this reaction. We measured OH radicals, isoprene and other species that are either precursors of OH or promote OH recycling (e.g. O3, NOx, HO2, H2O) with high time resolution (1-10 Hz) closely above a rain forest canopy (at 41 m above ground level) at the ATTO (Amazon Tall Tower Observatory) site (02°08'38.8''S, 58°59'59.5''W). The site is characterized by high isoprene (up to 20 ppb) and low NO (50 -500 ppt). Simultaneous measurements of OH and isoprene with high time resolution so far have been sparse. To our

Results from MARBLE DT Experiments on the National Ignition Facility: Implosion of Foam-Filled Capsules for Studying Thermonuclear Burn in the Presence of Heterogeneous Mix

Science.gov (United States)

Murphy, T. J.; Douglas, M. R.; Cardenas, T.; Cooley, J. H.; Gunderson, M. A.; Haines, B. M.; Hamilton, C. E.; Kim, Y.; Lee, M. N.; Oertel, J. A.; Olson, R. E.; Randolph, R. B.; Shah, R. C.; Smidt, J. M.

2017-10-01

The MARBLE campaign on NIF investigates the effect of heterogeneous mix on thermonuclear burn for comparison to a probability distribution function (PDF) burn model. MARBLE utilizes plastic capsules filled with deuterated plastic foam and tritium gas. The ratio of DT to DD neutron yield is indicative of the degree to which the foam and the gas atomically mix. Platform development experiments have been performed to understand the behavior of the foam and of the gas separately using two types of capsule. The first experiments using deuterated foam and tritium gas have been performed. Results of these experiments, and the implications for our understanding of thermonuclear burn in heterogeneously mixed separated reactant experiments will be discussed. This work is supported by US DOE/NNSA, performed at LANL, operated by LANS LLC under contract DE-AC52-06NA25396.

Production of L-lactic acid from Cassava peel wastes using single and mixed cultures of Rhizopus oligosporus and Lactobacillus plantarum

Directory of Open Access Journals (Sweden)

Nwokoro Ogbonnaya

2014-01-01

Full Text Available Production of L-lactic acid using cultures of Rhizopus oligosporus and Lactobacillus plantarum was investigated. Cassava peels were hydrolyzed by boiling for 1 h in either NaOH or HCl solutions followed by neutralization to a pH of 6.2. Reducing sugar produced from the hydrolysates increased with increasing concentrations of alkali or acid. Samples hydrolyzed with HCl produced a maximum reducing sugar concentration of 402 mg/g substrate while alkali hydrolyzed samples produced a maximum reducing sugar concentration of 213 mg/g substrate. Hydrolysates were amended with 0.5% ammonium sulphate solution and inoculated with either single or mixed cultures of Rhizopus oligosporus and Lactobacillus plantarum and incubated for 48 h for lactic acid production. The best lactic acid production of 50.2 g/100g substrate was observed in a mixed culture fermentation of acid hydrolyzed peels. Mixed culture fermentation of alkali hydrolyzed peels produced a maximum lactic acid concentration of 36.4 g/100g substrate. Un hydrolyzed cassava peels inoculated with a mixed culture of the microorganisms produced only 4.6 g/100g substrate. This work reports an efficient use of cassava peels for bio-product formation through microbial fermentation.

Single-implant overdentures retained by the Novaloc attachment system: study protocol for a mixed-methods randomized cross-over trial.

Science.gov (United States)

de Souza, Raphael F; Bedos, Christophe; Esfandiari, Shahrokh; Makhoul, Nicholas M; Dagdeviren, Didem; Abi Nader, Samer; Jabbar, Areej A; Feine, Jocelyne S

2018-04-23

Overdentures retained by a single implant in the midline have arisen as a minimal implant treatment for edentulous mandibles. The success of this treatment depends on the performance of a single stud attachment that is susceptible to wear-related retention loss. Recently developed biomaterials used in attachments may result in better performance of the overdentures, offering minimal retention loss and greater patient satisfaction. These biomaterials include resistant polymeric matrixes and amorphous diamond-like carbon applied on metallic components. The objective of this explanatory mixed-methods study is to compare Novaloc, a novel attachment system with such characteristics, to a traditional alternative for single implants in the mandible of edentate elderly patients. We will carry out a randomized cross-over clinical trial comparing Novaloc attachments to Locators for single-implant mandibular overdentures in edentate elderly individuals. Participants will be followed for three months with each attachment type; patient-based, clinical, and economic outcomes will be gathered. A sample of 26 participants is estimated to be required to detect clinically relevant differences in terms of the primary outcome (patient ratings of general satisfaction). Participants will choose which attachment they wish to keep, then be interviewed about their experiences and preferences with a single implant prosthesis and with the two attachments. Data from the quantitative and qualitative assessments will be integrated through a mixed-methods explanatory strategy. A last quantitative assessment will take place after 12 months with the preferred attachment; this latter assessment will enable measurement of the attachments' long-term wear and maintenance requirements. Our results will lead to evidence-based recommendations regarding these systems, guiding providers and patients when making decisions on which attachment systems and implant numbers will be most appropriate for

Multiplicative mixing of object identity and image attributes in single inferior temporal neurons.

Science.gov (United States)

Ratan Murty, N Apurva; Arun, S P

2018-04-03

Object recognition is challenging because the same object can produce vastly different images, mixing signals related to its identity with signals due to its image attributes, such as size, position, rotation, etc. Previous studies have shown that both signals are present in high-level visual areas, but precisely how they are combined has remained unclear. One possibility is that neurons might encode identity and attribute signals multiplicatively so that each can be efficiently decoded without interference from the other. Here, we show that, in high-level visual cortex, responses of single neurons can be explained better as a product rather than a sum of tuning for object identity and tuning for image attributes. This subtle effect in single neurons produced substantially better population decoding of object identity and image attributes in the neural population as a whole. This property was absent both in low-level vision models and in deep neural networks. It was also unique to invariances: when tested with two-part objects, neural responses were explained better as a sum than as a product of part tuning. Taken together, our results indicate that signals requiring separate decoding, such as object identity and image attributes, are combined multiplicatively in IT neurons, whereas signals that require integration (such as parts in an object) are combined additively. Copyright © 2018 the Author(s). Published by PNAS.

Mixed Reality Systems

OpenAIRE

Dieter Müller

2009-01-01

Currently one of the most challenging aspects of human computer interaction design is the integration of physical and digital worlds in a single environment. This fusion involves the development of "Mixed Reality Systems”, including various technologies from the domains of augmented and virtual reality. In this paper I will present related concepts and discuss lessons learned from our own research and prototype development. Our recent work involves the use of mixed reality (as opposed to ‘pur...

Preparation of single phase molybdenum boride

International Nuclear Information System (INIS)

Camurlu, Hasan Erdem

2011-01-01

Highlights: → Formation of Mo and a mixture of molybdenum boride phases take place in preparation of molybdenum borides. → It is intricate to prepare single phase molybdenum borides. → Formation of single phase MoB from MoO 3 + B 2 O 3 + Mg mixtures has not been reported previously. → Single phase MoB was successfully prepared through a combination of mechanochemical synthesis and annealing process. - Abstract: The formation of MoB through volume combustion synthesis (VCS), and through mechanochemical synthesis (MCS) followed by annealing has been investigated. MoO 3 , B 2 O 3 and Mg were used as reactants while MgO and NaCl were introduced as diluents. Products were leached in dilute HCl solution and were subjected to X-ray diffraction (XRD) analysis and scanning electron microscopy (SEM) examinations. Mo was the major phase component in the VCS products under all the experimental conditions. Mo 2 B, MoB, MoB 2 and Mo 2 B 5 were found as minor phases. Products of MCS contained a mixture of Mo 2 B, MoB, MoB 2 and Mo. After annealing the MCS product at 1400 deg. C for 3 h, single phase α-MoB was obtained.

Thermal properties of the mixed spin-1 and spin-3/2 Ising ferrimagnetic system with two different random single-ion anisotropies

Science.gov (United States)

Pereira, J. R. V.; Tunes, T. M.; de Arruda, A. S.; Godoy, M.

2018-06-01

In this work, we have performed Monte Carlo simulations to study a mixed spin-1 and spin-3/2 Ising ferrimagnetic system on a square lattice with two different random single-ion anisotropies. This lattice is divided in two interpenetrating sublattices with spins SA = 1 in the sublattice A and SB = 3 / 2 in the sublattice B. The exchange interaction between the spins on the sublattices is antiferromagnetic (J single-ion anisotropies, DiA and DjB , on the sublattices A and B, respectively. We have determined the phase diagram of the model in the critical temperature Tc versus strength of the random single-ion anisotropy D plane and we shown that it exhibits only second-order phase transition lines. We also shown that this system displays compensation temperatures for some cases of the random single-ion distribution.

9 CFR 114.6 - Mixing biological products.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Mixing biological products. 114.6... BIOLOGICAL PRODUCTS § 114.6 Mixing biological products. Each biological product, when in liquid form, shall be mixed thoroughly in a single container. During bottling operations, the product shall be...

Mixed methods for telehealth research.

Science.gov (United States)

Caffery, Liam J; Martin-Khan, Melinda; Wade, Victoria

2017-10-01

Mixed methods research is important to health services research because the integrated qualitative and quantitative investigation can give a more comprehensive understanding of complex interventions such as telehealth than can a single-method study. Further, mixed methods research is applicable to translational research and program evaluation. Study designs relevant to telehealth research are described and supported by examples. Quality assessment tools, frameworks to assist in the reporting and review of mixed methods research, and related methodologies are also discussed.

Impact of growth conditions and role of sigB on Listeria monocytogenes fitness in single and mixed biofilms cultured with Lactobacillus plantarum

NARCIS (Netherlands)

Saa Ibusquiza, P.; Nierop Groot, M.N.; Deban Valles, A.; Abee, T.; Besten, den H.M.W.

2015-01-01

The role of sigB, a major transcriptional regulator of stress response genes, was assessed in formation of single and mixed species biofilms of Listeria monocytogenes EGD-e and Lactobacillus plantarum WCFS1 as secondary species at 20 °C and 30 °C using different medium compositions (nutrient-rich

Mixed quantization dimensions of self-similar measures

International Nuclear Information System (INIS)

Dai Meifeng; Wang Xiaoli; Chen Dandan

2012-01-01

Highlights: ► We define the mixed quantization dimension of finitely many measures. ► Formula of mixed quantization dimensions of self-similar measures is given. ► Illustrate the behavior of mixed quantization dimension as a function of order. - Abstract: Classical multifractal analysis studies the local scaling behaviors of a single measure. However recently mixed multifractal has generated interest. The purpose of this paper is some results about the mixed quantization dimensions of self-similar measures.

Switching from Reactant to Substrate Engineering in the Selective Synthesis of Graphene Nanoribbons.

Science.gov (United States)

Merino-Díez, Néstor; Lobo-Checa, Jorge; Nita, Pawel; Garcia-Lekue, Aran; Basagni, Andrea; Vasseur, Guillaume; Tiso, Federica; Sedona, Francesco; Das, Pranab K; Fujii, Jun; Vobornik, Ivana; Sambi, Mauro; Pascual, José Ignacio; Ortega, J Enrique; de Oteyza, Dimas G

2018-04-27

The challenge of synthesizing graphene nanoribbons (GNRs) with atomic precision is currently being pursued along a one-way road, based on the synthesis of adequate molecular precursors that react in predefined ways through self-assembly processes. The synthetic options for GNR generation would multiply by adding a new direction to this readily successful approach, especially if both of them can be combined. We show here how GNR synthesis can be guided by an adequately nanotemplated substrate instead of by the traditionally designed reactants. The structural atomic precision, unachievable to date through top-down methods, is preserved by the self-assembly process. This new strategy's proof-of-concept compares experiments using 4,4''-dibromo-para-terphenyl as a molecular precursor on flat Au(111) and stepped Au(322) substrates. As opposed to the former, the periodic steps of the latter drive the selective synthesis of 6 atom-wide armchair GNRs, whose electronic properties have been further characterized in detail by scanning tunneling spectroscopy, angle resolved photoemission, and density functional theory calculations.

Unidirectional ring-laser operation using sum-frequency mixing

DEFF Research Database (Denmark)

Tidemand-Lichtenberg, Peter; Cheng, Haynes Pak Hay; Pedersen, Christian

2010-01-01

A technique enforcing unidirectional operation of ring lasers is proposed and demonstrated. The approach relies on sum-frequency mixing between a single-pass laser and one of the two counterpropagating intracavity fields of the ring laser. Sum-frequency mixing introduces a parametric loss for the...... where lossless second-order nonlinear materials are available. Numerical modeling and experimental demonstration of parametric-induced unidirectional operation of a diode-pumped solid-state 1342 nm cw ring laser are presented.......A technique enforcing unidirectional operation of ring lasers is proposed and demonstrated. The approach relies on sum-frequency mixing between a single-pass laser and one of the two counterpropagating intracavity fields of the ring laser. Sum-frequency mixing introduces a parametric loss...

Solar fuel production in a novel polymeric electrolyte membrane photoelectrochemical (PEM-PEC) cell with a web of titania nanotube arrays as photoanode and gaseous reactants

NARCIS (Netherlands)

Stoll, T.; Zafeiropoulos, G.; Tsampas, M. N.

2016-01-01

A novel photoelectrochemical (PEC) cell design is proposed and investigated for H-2 production with gaseous reactants. The core of the cell is a membrane electrode assembly (MEA) that consists of a TiO2 nanotube arrays photoanode, a Pt/C cathode, a Pt/C reference electrode and a proton conducting

Numerical modeling of two-phase binary fluid mixing using mixed finite elements

KAUST Repository

Sun, Shuyu

2012-07-27

Diffusion coefficients of dense gases in liquids can be measured by considering two-phase binary nonequilibrium fluid mixing in a closed cell with a fixed volume. This process is based on convection and diffusion in each phase. Numerical simulation of the mixing often requires accurate algorithms. In this paper, we design two efficient numerical methods for simulating the mixing of two-phase binary fluids in one-dimensional, highly permeable media. Mathematical model for isothermal compositional two-phase flow in porous media is established based on Darcy\\'s law, material balance, local thermodynamic equilibrium for the phases, and diffusion across the phases. The time-lag and operator-splitting techniques are used to decompose each convection-diffusion equation into two steps: diffusion step and convection step. The Mixed finite element (MFE) method is used for diffusion equation because it can achieve a high-order and stable approximation of both the scalar variable and the diffusive fluxes across grid-cell interfaces. We employ the characteristic finite element method with moving mesh to track the liquid-gas interface. Based on the above schemes, we propose two methods: single-domain and two-domain methods. The main difference between two methods is that the two-domain method utilizes the assumption of sharp interface between two fluid phases, while the single-domain method allows fractional saturation level. Two-domain method treats the gas domain and the liquid domain separately. Because liquid-gas interface moves with time, the two-domain method needs work with a moving mesh. On the other hand, the single-domain method allows the use of a fixed mesh. We derive the formulas to compute the diffusive flux for MFE in both methods. The single-domain method is extended to multiple dimensions. Numerical results indicate that both methods can accurately describe the evolution of the pressure and liquid level. © 2012 Springer Science+Business Media B.V.

Intercomparison of model simulations of mixed-phase clouds observed during the ARM Mixed-Phase Arctic Cloud Experiment. Part II: Multi-layered cloud

Energy Technology Data Exchange (ETDEWEB)

Morrison, H; McCoy, R B; Klein, S A; Xie, S; Luo, Y; Avramov, A; Chen, M; Cole, J; Falk, M; Foster, M; Genio, A D; Harrington, J; Hoose, C; Khairoutdinov, M; Larson, V; Liu, X; McFarquhar, G; Poellot, M; Shipway, B; Shupe, M; Sud, Y; Turner, D; Veron, D; Walker, G; Wang, Z; Wolf, A; Xu, K; Yang, F; Zhang, G

2008-02-27

Results are presented from an intercomparison of single-column and cloud-resolving model simulations of a deep, multi-layered, mixed-phase cloud system observed during the ARM Mixed-Phase Arctic Cloud Experiment. This cloud system was associated with strong surface turbulent sensible and latent heat fluxes as cold air flowed over the open Arctic Ocean, combined with a low pressure system that supplied moisture at mid-level. The simulations, performed by 13 single-column and 4 cloud-resolving models, generally overestimate the liquid water path and strongly underestimate the ice water path, although there is a large spread among the models. This finding is in contrast with results for the single-layer, low-level mixed-phase stratocumulus case in Part I of this study, as well as previous studies of shallow mixed-phase Arctic clouds, that showed an underprediction of liquid water path. The overestimate of liquid water path and underestimate of ice water path occur primarily when deeper mixed-phase clouds extending into the mid-troposphere were observed. These results suggest important differences in the ability of models to simulate Arctic mixed-phase clouds that are deep and multi-layered versus shallow and single-layered. In general, models with a more sophisticated, two-moment treatment of the cloud microphysics produce a somewhat smaller liquid water path that is closer to observations. The cloud-resolving models tend to produce a larger cloud fraction than the single-column models. The liquid water path and especially the cloud fraction have a large impact on the cloud radiative forcing at the surface, which is dominated by the longwave flux for this case.

Mixed Reality Systems

Directory of Open Access Journals (Sweden)

Dieter Müller

2009-11-01

Full Text Available Currently one of the most challenging aspects of human computer interaction design is the integration of physical and digital worlds in a single environment. This fusion involves the development of "Mixed Reality Systems”, including various technologies from the domains of augmented and virtual reality. In this paper I will present related concepts and discuss lessons learned from our own research and prototype development. Our recent work involves the use of mixed reality (as opposed to ‘pure’ virtual reality techniques to support seamless collaborative work between remote and hands-on laboratories.

Using mixed methods in health research.

OpenAIRE

Tariq, S.; Woodman, J.

2013-01-01

Mixed methods research is the use of quantitative and qualitative methods in a single study or series of studies. It is an emergent methodology which is increasingly used by health researchers, especially within health services research. There is a growing literature on the theory, design and critical appraisal of mixed methods research. However, there are few papers that summarize this methodological approach for health practitioners who wish to conduct or critically engage with mixed method...

Automatically varying the composition of a mixed refrigerant solution for single mixed refrigerant LNG (liquefied natural gas) process at changing working conditions

International Nuclear Information System (INIS)

Xu, Xiongwen; Liu, Jinping; Cao, Le; Pang, Weiqiang

2014-01-01

The SMR (single mixed refrigerant) process is widely used in the small- and medium-scale liquefaction of NG (natural gas). Operating the MR (mixed-refrigerant) process outside of the design specifications is difficult but essential to save energy. Nevertheless, it is difficult to realize because the process needs to alter the working refrigerant composition. To address this challenge, this study investigated the performance diagnosis mechanism for SMR process. A control strategy was then proposed to control the changes in working refrigerant composition under different working conditions. This strategy separates the working refrigerant flow in the SMR process into three flows through two phase separators before it flows into the cold box. The first liquid flow is rich in the high-temperature component (isopentane). The second liquid flow is rich in the middle-temperature components (ethylene and propane), and the gas flow is rich in the low-temperature components (nitrogen and methane). By adjusting the flow rates, it is easy to decouple the control variables and automate the system. Finally, this approach was validated by process simulation and shown to be highly adaptive and exergy efficient in response to changing working conditions. - Highlights: • The performance diagnosis mechanism of SMR LNG process is studied. • A measure to automatically change the operation composition as per the working conditions is proposed for SMR process. • SMR process simulation is performed to verify the validity of the control solution. • The control solution notably improves the energy efficiency of SMR process at changing working condition

Investigations on mixing phenomena in single-phase flow in a T-junction geometry

International Nuclear Information System (INIS)

Walker, C.; Simiano, M.; Zboray, R.; Prasser, H.-M.

2009-01-01

The paper deals with T-junction mixing experiments carried out with wire-mesh sensors. The mixing of coolant streams of different temperature in pipe junctions leads to temperature fluctuations that may cause thermal fatigue in the pipe wall. This is practical background for an increased interest in measuring and predicting the transient flow field and the turbulent mixing pattern downstream of a T-junction. Experiments were carried out at a perpendicular connection of two pipes of 51 mm inner diameter. The straight and the side branches were supplied by water of different electrical conductivity, which replaced the temperature in the thermal mixing process. A set of three wire-mesh sensors with a grid of 16 x 16 measuring points each was used to record conductivity distributions downstream of the T-junction. Besides the measurement of profiles of the time averaged mixing scalar over extended measuring domains, the high resolution in time and space of the mesh sensors allow a statistic characterization of the stochastic fluctuations of the mixing scalar in a wide range of frequencies. Information on the scale of turbulent mixing patterns is obtained by cross-correlating the signal fluctuations recorded at different locations within the measuring plane of a sensor

Mixed Methods and Action Research: similar or different?

OpenAIRE

Wiśniewska, Danuta

2011-01-01

This article attempts to analyse and compare ELT studies grounded solely in mixed methods and ELT action research studies based on a mixed methods approach in order to identify to what degree action research studies combining different methods in a single study comply with the principles of rigorous mixed methods study.

Comparing a single case to a control group - Applying linear mixed effects models to repeated measures data.

Science.gov (United States)

Huber, Stefan; Klein, Elise; Moeller, Korbinian; Willmes, Klaus

2015-10-01

In neuropsychological research, single-cases are often compared with a small control sample. Crawford and colleagues developed inferential methods (i.e., the modified t-test) for such a research design. In the present article, we suggest an extension of the methods of Crawford and colleagues employing linear mixed models (LMM). We first show that a t-test for the significance of a dummy coded predictor variable in a linear regression is equivalent to the modified t-test of Crawford and colleagues. As an extension to this idea, we then generalized the modified t-test to repeated measures data by using LMMs to compare the performance difference in two conditions observed in a single participant to that of a small control group. The performance of LMMs regarding Type I error rates and statistical power were tested based on Monte-Carlo simulations. We found that starting with about 15-20 participants in the control sample Type I error rates were close to the nominal Type I error rate using the Satterthwaite approximation for the degrees of freedom. Moreover, statistical power was acceptable. Therefore, we conclude that LMMs can be applied successfully to statistically evaluate performance differences between a single-case and a control sample. Copyright © 2015 Elsevier Ltd. All rights reserved.

Achieving maximum sustainable yield in mixed fisheries

NARCIS (Netherlands)

Ulrich, Clara; Vermard, Youen; Dolder, Paul J.; Brunel, Thomas; Jardim, Ernesto; Holmes, Steven J.; Kempf, Alexander; Mortensen, Lars O.; Poos, Jan Jaap; Rindorf, Anna

2017-01-01

Achieving single species maximum sustainable yield (MSY) in complex and dynamic fisheries targeting multiple species (mixed fisheries) is challenging because achieving the objective for one species may mean missing the objective for another. The North Sea mixed fisheries are a representative example

Cowpea viruses: Effect of single and mixed infections on symptomatology and virus concentration

Directory of Open Access Journals (Sweden)

Nsa Imade Y

2007-09-01

Full Text Available Abstract Natural multiple viral infections of cultivated cowpeas have been reported in Nigeria. In this study, three Nigerian commercial cowpea cultivars ("Olo 11", "Oloyin" and "White" and two lines from the IITA (IT86D- 719 and TVU 76 were mechanically inoculated with Cowpea aphid-borne mosaic virus (CABMV, Bean southern mosaic virus (SBMV and Cowpea mottle virus (CMeV singly, as well as in all possible combinations at 10, 20 and 30 days after planting (DAP. Samples of leaves or stems were collected at 10, 20 and 30 days after inoculation (DAI and analyzed for relative virus concentration by Enzyme-Linked Immunosrbent Assay. All the cultivars and lines {CVS/L} were susceptible to the viruses but the commercial CVS showed more severe symptoms and had relatively higher viral concentration. In single virus infections, CABMV which induced the most severe symptoms had absorbance values (at 405 nm of 0.11 to 0.46 while SBMV and CMeV which induced moderate symptoms had virus titre of 0.74 to 1.99 and 0.11 to 0.90 respectively. Plants inoculated 10 DAP had significantly higher virus concentration than those inoculated 30 DAP. In mixed infections involving CABMV (10 DAP apical necrosis and death were observed in commercial cultivars "Olo 11" and "White". Enhancement of CMeV titers were observed in plants infected with CMeV + CABMV. Multiple viral infections of cowpeas may result in complete yield loss, hence, the availability of seeds of cultivars with a high level of multiple virus resistance is recommended as a means of control.

Exactly solved mixed spin-(1,1/2) Ising–Heisenberg diamond chain with a single-ion anisotropy

International Nuclear Information System (INIS)

Lisnyi, Bohdan; Strečka, Jozef

2015-01-01

The mixed spin-(1,1/2) Ising–Heisenberg diamond chain with a single-ion anisotropy is exactly solved through the generalized decoration–iteration transformation and the transfer-matrix method. The decoration–iteration transformation is first used for establishing a rigorous mapping equivalence with the corresponding spin-1 Blume–Emery–Griffiths chain, which is subsequently exactly treated within the transfer-matrix technique. Apart from three classical ground states the model exhibits three striking quantum ground states in which a singlet-dimer state of the interstitial Heisenberg spins is accompanied either with a frustrated state or a polarized state or a non-magnetic state of the nodal Ising spins. It is evidenced that two magnetization plateaus at zero and/or one-half of the saturation magnetization may appear in low-temperature magnetization curves. The specific heat may display remarkable temperature dependences with up to three and four distinct round maxima in a zero and non-zero magnetic field, respectively. - Highlights: • Mixed spin-(1,1/2) Ising–Heisenberg diamond chain is exactly solved. • Quantum ground states with a singlet-dimer state of the Heisenberg spins are found. • Magnetization curve displays intermediate plateaus at zero and half of full magnetization. • Thermal dependences of specific heat may display up to four distinct peaks

Reconfigurable Mixed Mode Universal Filter

Directory of Open Access Journals (Sweden)

Neelofer Afzal

2014-01-01

Full Text Available This paper presents a novel mixed mode universal filter configuration capable of working in voltage and transimpedance mode. The proposed single filter configuration can be reconfigured digitally to realize all the five second order filter functions (types at single output port. Other salient features of proposed configuration include independently programmable filter parameters, full cascadability, and low sensitivity figure. However, all these features are provided at the cost of quite large number of active elements. It needs three digitally programmable current feedback amplifiers and three digitally programmable current conveyors. Use of six active elements is justified by introducing three additional reduced hardware mixed mode universal filter configurations and its comparison with reported filters.

Mixing Ventilation System in a Single-Aisle Aircraft Cabin

DEFF Research Database (Denmark)

Nielsen, Peter Vilhelm; Zhang, Chen; Wojcik, Kamil

2014-01-01

. It is also proven possible to create an acceptable draught level in the cabin. Experiments with tracer gas indicated that the contaminant from exhalation of one manikin is fully mixed in the cabin, and the experiment with personalised ventilation did not show much improvement in this situation....

Influence of basic properties of Mg,Al-mixed oxides on their catalytic activity in knoevenagel condensation between benzaldehyde and phenylsulfonylacetonitrile

Directory of Open Access Journals (Sweden)

Caridad Noda Pérez

2009-01-01

Full Text Available The catalytic performance of Mg,Al-mixed oxides (MO20, MO25 and MO33 derived from hydrotalcites was evaluated in the Knoevenagel reaction between benzaldehyde and phenylsulfonylacetonitrile at 373 and 383 K. The best results were obtained for the sample MO20 that presented the highest basic sites density and external area and the smallest crystallite sizes. The relative amount of basic sites with weak to intermediate strength also played an important role on catalytic performance. By increasing the catalyst content from 1 to 5 wt.% at 383 K, a complete conversion of the reactants is attained, producing α-phenylsulfonylcinnamonitrile with a selectivity of 100%.

Temperature modulation and quadrature detection for selective titration of two-state exchanging reactants.

Science.gov (United States)

Zrelli, K; Barilero, T; Cavatore, E; Berthoumieux, H; Le Saux, T; Croquette, V; Lemarchand, A; Gosse, C; Jullien, L

2011-04-01

Biological samples exhibit huge molecular diversity over large concentration ranges. Titrating a given compound in such mixtures is often difficult, and innovative strategies emphasizing selectivity are thus demanded. To overcome limitations inherent to thermodynamics, we here present a generic technique where discrimination relies on the dynamics of interaction between the target of interest and a probe introduced in excess. Considering an ensemble of two-state exchanging reactants submitted to temperature modulation, we first demonstrate that the amplitude of the out-of-phase concentration oscillations is maximum for every compound involved in a reaction whose equilibrium constant is equal to unity and whose relaxation time is equal to the inverse of the excitation angular frequency. Taking advantage of this feature, we next devise a highly specific detection protocol and validate it using a microfabricated resistive heater and an epifluorescence microscope, as well as labeled oligonucleotides to model species displaying various dynamic properties. As expected, quantification of a sought for strand is obtained even if interfering reagents are present in similar amounts. Moreover, our approach does not require any separation and is compatible with imaging. It could then benefit some of the numerous binding assays performed every day in life sciences.

Re-Examination of Mixed Media Communication: The Impact of Voice, Data Link, and Mixed Air Traffic Control Environments on the Flight Deck

Science.gov (United States)

Dunbar, Melisa; McGann, Alison; Mackintosh, Margaret-Anne; Lozito, Sandra; Ashford, Rose (Technical Monitor)

2001-01-01

A simulation in the B747-400 was conducted at NASA Ames Research Center that compared how crews handled voice and data link air traffic control (ATC) messages in a single medium versus a mixed voice and data link ATC environment The interval between ATC messages was also varied to examine the influence of time pressure in voice, data link, and mixed ATC environments. For messages sent via voice, transaction times were lengthened in the mixed media environment for closely spaced messages. The type of environment did not affect data link times. However, messages times were lengthened in both single and mixed-modality environments under time pressure. Closely spaced messages also increased the number of requests for clarification for voice messages in the mixed environment and review menu use for data link messages. Results indicated that when time pressure is introduced, the mix of voice and data link does not necessarily capitalize on the advantages of both media. These findings emphasize the need to develop procedures for managing communication in mixed voice and data link environments.

Unsteady single-phase natural circulation flow mixing prediction using CATHARE three-dimensional capabilities

Energy Technology Data Exchange (ETDEWEB)

Salah, Anis Bousbia; Vlassenbroeck, Jacques [Bel V - Subsidiary of the Belgian Federal Agency for Nuclear Contro, Brussels (Belize)

2017-04-15

Coolant mixing under natural circulation flow regime constitutes a key parameter that may play a role in the course of an accidental transient in a nuclear pressurized water reactor. This issue has motivated some experimental investigations carried out within the OECD/NEA PKL projects. The aim was to assess the coolant mixing phenomenon in the reactor pressure vessel downcomer and the core lower plenum under several asymmetric steady and unsteady flow conditions, and to provide experimental data for code validations. Former studies addressed the mixing phenomenon using, on the one hand, one-dimensional computational approaches with cross flows that are not fully validated under transient conditions and, on the other hand, expensive computational fluid dynamic tools that are not always justified for large-scale macroscopic phenomena. In the current framework, an unsteady coolant mixing experiment carried out in the Rossendorf coolant mixing test facility is simulated using the three-dimensional porous media capabilities of the thermal–hydraulic system CATHARE code. The current study allows highlighting the current capabilities of these codes and their suitability for reproducing the main phenomena occurring during asymmetric transient natural circulation mixing conditions.

Two series of reactant's ratio-dependent lanthanide organic frameworks derived from nicotinic acid N-oxide and oxalate: synthesis, crystal structures and luminescence properties.

Science.gov (United States)

Yu, Yanyan; Zhang, Lijuan; Zhou, Yunshan; Zuhra, Zareen

2015-03-14

Two series of lanthanide(III)–organic frameworks with the molecular formula [Ln2(NNO)2(OX)2(H2O)4]n (Ln = Eu 1, Tb 2, Sm 3, Dy 4, Gd 5) and [Ln2(NNO)4(OX)(H2O)2]n (Ln = Eu 6, Tb 7, Sm 8, Dy 9, Gd 10) were synthesized successfully under the same hydrothermal conditions with nicotinic N-oxide (HNNO) and oxalic acid (H2OX) as the mixed ligands merely through varying the molar ratio of the reactants. The compounds were characterized by IR, elemental analysis, UV, TG-DTA and powder X-ray diffraction (XRD). X-ray single-crystal diffraction analyses of compounds 1 and 7 selected as representatives and powder XRD analysis of the compounds revealed that both the series of compounds feature three-dimensional (3-D) open frameworks, and crystallize in the triclinic P1 space group while with different unit cell parameters. In compound 1, pairs of Eu(3+) ions and pairs of NNO(−) ligands connect with each other alternately to form a 1-D infinite Eu-NNO double chain, the adjacent 1-D double-chains are then joined together through OX(2−) ligands leading to a 2D layer, the 2-D layers are further ‘pillared’ by OX(2−) ligands resulting in a 3-D framework. In compound 7, the 1-D Tb-NNO infinite chain and its 2-D layer are formed in an almost similar fashion to that in compound 1. The difference between the structures of the two compounds 1 and 7 is that the adjacent 2-D layers in compound 7 are further connected by NNO(−) ligands resulting in a 3-D framework. The photoluminescence properties and energy transfer mechanism of the compounds were studied systematically. The energy level of the lowest triplet states of the HNNO ligand (23148 cm(−1)) was determined based on the phosphorescence spectrum of compound 5 at 77 K. The (5)D0 (Eu(3+)) and (5)D4 (Tb(3+)) emission lifetimes are 0.46 ms, 0.83 ms, 0.69 ms and 0.89 ms and overall quantum yields are 1.03%, 3.29%, 2.58% and 3.78% for the compounds 1, 2, 6 and 7, respectively.

Preliminary Single-Phase Mixing Test using Wire Mesh System in a wire-wrapped 37-rod Bundle

International Nuclear Information System (INIS)

Bae, Hwang; Kim, Hyungmo; Lee, Dong Won; Choi, Hae Seob; Choi, Sun Rock; Chang, Seokkyu; Kim, Seok; Euh, Dongjin; Lee, Hyeongyeon

2014-01-01

In this paper, preliminary tests of the wire-mesh sensor are introduced before measuring of mixing coefficient in the wire-wrapped 37-pin fuel assembly for a sodium-cooled fast reactor. Through this preliminary test, it was confirmed that city water can be used as a tracer for demineralized water as a base. A simple test was performed to evaluate the characteristics of a wire mesh with of a short pipe shape. The conductivity of de-mineralized water and city water is linearly increased for the limited temperature ranges as the temperature is increased. The reliability of the wire mesh sensor was estimated based on the averages and standard deviations of the plane image using the cross points. A wire mesh sensor is suitable to apply to a single-phase flow measurement for a mixture with de-mineralized water and city water. A wire mesh sensor and system have been traditionally used to measure the void fraction of a two-phase flow field with gas and liquid. Recently, Ylonen et al. successfully designed and commissioned a measurement system for a single-phase flow using a wire mesh sensor

CFD Simulations of a Single-phase Mixing Experiment

International Nuclear Information System (INIS)

Bertolotto, Davide; Chawla, Rakesh; Manera, Annalisa; Prasser, Horst-Michael

2008-01-01

The current paper reports on an investigation of the capabilities of CFD codes to model multidimensional mixing phenomena in a loop. For the purpose, a test facility consisting of two loops connected by a double T-junction has been built at the Paul Scherrer Institut (PSI). Experiments were carried out, in which a tracer was injected in one loop and the tracer distribution before and after the T-junction was measured by means of wire-mesh sensors located at the outlets of the junction. The tracer distribution after the T-junction is strongly dependent on 3D mixing phenomena, which are dominant due to the particular geometry of the set-up. For the CFD analysis, a 3D model of the double T-junction was created, and different simulations were performed with ANSYS-CFX to study the sensitivity of the results with respect to parameters such as mesh refinement, integration time step, turbulence model, profiles for inlet velocity and injected tracer concentration. Thereafter, these results were compared with the experimental data. The comparisons have clearly pointed out that 3D modelling is able to reproduce (at least qualitatively) the experimental results. Moreover, it has been found that the CFD results are strongly influenced by the velocity profile assumptions at the inlets of the double T-junction. (authors)

Mixed Methods Research Designs in Counseling Psychology

Science.gov (United States)

Hanson, William E.; Creswell, John W.; Clark, Vicki L. Plano; Petska, Kelly S.; Creswell, David J.

2005-01-01

With the increased popularity of qualitative research, researchers in counseling psychology are expanding their methodologies to include mixed methods designs. These designs involve the collection, analysis, and integration of quantitative and qualitative data in a single or multiphase study. This article presents an overview of mixed methods…

Charm mixing at LHCb

CERN Document Server

Di Canto, Angelo

2013-01-01

We report a measurement of the time-dependent ratio of $D^0\\to K^+\\pi^-$ to $D^0\\to K^-\\pi^+$ decay rates in $D^{*+}$-tagged events using 1.0\\,fb$^{-1}$ of integrated luminosity recorded by the LHCb experiment. We measure the mixing parameters $x'^2=(-0.9\\pm1.3)\\times10^{-4}$, $y'=(7.2\\pm2.4)\\times10^{-3}$ and the ratio of doubly-Cabibbo-suppressed to Cabibbo-favored decay rates $R_D=(3.52\\pm0.15)\\times10^{-3}$. The result excludes the no-mixing hypothesis with a probability corresponding to 9.1 standard deviations and represents the first observation of charm mixing from a single measurement

A three-dimensional numerical investigation of trapezoid baffles effect on non-isothermal reactant transport and cell net power in a PEMFC

International Nuclear Information System (INIS)

Perng, Shiang-Wuu; Wu, Horng-Wen

2015-01-01

Highlights: • We study how angle and height of trapezoid baffle affect PEMFC net power. • The jet-type, trapping, and blockage effects augment non-isothermal transport in flow channel. • Greater angles and heights of trapezoid baffles provide more reactant to the catalyst layer. • Baffles of 1.5 mm and 90° fully block flow channel to show bad heat transfer and large pressure drop. • Maximum enhancement of cell net power is 90% with baffles of 60° angle and 1.125 mm height. - Abstract: The present study performed a three-dimensional numerical simulation to observe how trapezoid baffles affect non-isothermal reactant transports and cell net power in the proton exchange membrane fuel cell (PEMFC) by the SIMPLE-C method. The geometric parameters of trapezoid baffles installed in the gas channel employed in this study include the angle and height with the same gas diffusion and catalyst layers to realize the cell net power considering the effect of liquid water formation on the fluid flow field. The cell net power is adopted to evaluate the real enhancement of cell performance due to the additional pumping power induced by the pressure loss through the PEMFC. The results illustrated that compared with traditional gas channel without baffles, the novel gas channel with trapezoid baffles, whose angle is 60° and height is 1.125 mm, enhances the cell net power best by approximately 90% among all trapezoid baffle designs

PIV measurement of turbulent bubbly mixing layer flow with polymer additives

International Nuclear Information System (INIS)

Ning, T; Guo, F; Chen, B; Zhang, X

2009-01-01

Based on experimental investigation of single-phase turbulent mixing layer flow with polymer additives, bubbly mixing layer was experimentally investigated by PIV. The velocity ratio between high and low speed is 4:1 and the Reynolds number based on the velocity difference of two steams and hydraulic diameter of the channel ranges is 73333. Gas bubbles with about 0.5% gas fraction were injected into pure water mixing layer with/without polymer additives from three different parts at the end of the splitter plate. The comparison between single phase and bubbly mixing layer shows clearly that the dynamic development of mixing layer is great influenced by the bubble injection. Similar with single phase, the Reynolds stress and vorticity still concentrate in a coniform area of central mixing flow field part and the width will increase with increasing the Reynolds number. Mean Reynolds stress will decrease with bubble injection in high Reynolds numbers and the decreasing of Reynolds stress with polymer additives is much more than pure water case.

Pattern of neutrino mixing in grand unified theories

International Nuclear Information System (INIS)

Milton, K.; Tanaka, K.

1981-01-01

It was found previously in SO(10) grand unified theories that if the neutrinos have a Dirac mass and a right-handed Majorana mass (approx. 10 15 GeV) but no left-handed Majorana mass, there is small ν/sub e/ mixing but ν/sub μ/ - ν/sub tau/ mixing can be substantial. This problem is reexamined on the basis of a formalism that assumes that the up, down, lepton, and neutrino mass matrices arise from a single complex 10 and a single 126 Higgs boson. This formalism determines the Majorana mass matrix in terms of quark mass matrices. Adopting three different sets of quark mass matrices that produce acceptable fermion mass ratios and Cabbibo mixing produces results consistent with the above; however, in the optimum case, ν/sub e/ - ν/sub μ/ mixing can be of the order of the Cabbibo angle

Study of temperature, air dew point temperature and reactant flow effects on proton exchange membrane fuel cell performances using electrochemical spectroscopy and voltammetry techniques

Energy Technology Data Exchange (ETDEWEB)

Wasterlain, S.; Hissel, D. [FC LAB, Techn' Hom, rue Thierry Mieg, 90010 Belfort Cedex (France); FEMTO-ST (UMR CNRS 6174), ENISYS Department, University of Franche-Comte, Techn' Hom, rue Thierry Mieg, 90010 Belfort Cedex (France); Candusso, D.; Harel, F. [FC LAB, Techn' Hom, rue Thierry Mieg, 90010 Belfort Cedex (France); INRETS, The French National Institute for Transport and Safety Research, Techn' Hom, rue Thierry Mieg, 90010 Belfort Cedex (France); Bergman, P.; Menard, P.; Anwar, M. [University of Connecticut, Connecticut Global Fuel Cell Center Department of Electrical and Computer Engineering, 44 Weaver Road, Unit 5233, Storrs, CT 06269-5233 (United States)

2010-02-15

A single PEMFC has been operated by varying the assembly temperature, the air dew point temperature and the anode/cathode stoichiometry rates with the aim to identify the parameters and combinations of factors affecting the cell performance. Some of the experiments were conducted with low humidified reactants (relative humidity of 12%). The FC characterizations tests have been conducted using in situ electrochemical methods based on load current and cell voltage signal analysis, namely: polarization curves, EIS measurements, cyclic and linear sweep voltammetries (CV and LSV). The impacts of the parameters on the global FC performances were observed using the polarization curves whereas EIS, CV and LSV test results were used to discriminate the different voltage loss sources. The test results suggest that some parameter sets allow maximal output voltages but can also induce material degradation. For instance, higher FC temperature and air flow values can induce significant electrical efficiency benefits, notably by increasing the reversible potential and the reaction kinetics. However, raising the cell temperature can also gradually dry the FC and increase the risk of membrane failure. LSV has also shown that elevated FC temperature and relative humidity can also accelerate the electrolyte degradation (i.e. slightly higher fuel crossover rate) and reduce the lifetime consequently. (author)

Study of temperature, air dew point temperature and reactant flow effects on proton exchange membrane fuel cell performances using electrochemical spectroscopy and voltammetry techniques

Science.gov (United States)

Wasterlain, S.; Candusso, D.; Hissel, D.; Harel, F.; Bergman, P.; Menard, P.; Anwar, M.

A single PEMFC has been operated by varying the assembly temperature, the air dew point temperature and the anode/cathode stoichiometry rates with the aim to identify the parameters and combinations of factors affecting the cell performance. Some of the experiments were conducted with low humidified reactants (relative humidity of 12%). The FC characterizations tests have been conducted using in situ electrochemical methods based on load current and cell voltage signal analysis, namely: polarization curves, EIS measurements, cyclic and linear sweep voltammetries (CV and LSV). The impacts of the parameters on the global FC performances were observed using the polarization curves whereas EIS, CV and LSV test results were used to discriminate the different voltage loss sources. The test results suggest that some parameter sets allow maximal output voltages but can also induce material degradation. For instance, higher FC temperature and air flow values can induce significant electrical efficiency benefits, notably by increasing the reversible potential and the reaction kinetics. However, raising the cell temperature can also gradually dry the FC and increase the risk of membrane failure. LSV has also shown that elevated FC temperature and relative humidity can also accelerate the electrolyte degradation (i.e. slightly higher fuel crossover rate) and reduce the lifetime consequently.

Phase transitions and multicritical points in the mixed spin-32 and spin-2 Ising system with a single-ion anisotropy

International Nuclear Information System (INIS)

Bobak, A.; Dely, J.

2007-01-01

The effect of a single-ion anisotropy on the phase diagram of the mixed spin-32 and spin-2 Ising system is investigated by the use of a mean-field theory based on the Bogoliubov inequality for the free energy. Topologically different kinds of phase diagrams are achieved by changing values of the parameter in the model Hamiltonian. Besides second-order transitions, lines of first-order transitions terminating either at a tricritical point or an isolated critical point, are found

On entanglement in neutrino mixing and oscillations

International Nuclear Information System (INIS)

Blasone, Massimo; Dell'Anno, Fabio; De Siena, Silvio; Illuminati, Fabrizio

2010-01-01

We report on recent results about entanglement in the context of particle mixing and oscillations. We study in detail single-particle entanglement arising in two-flavor neutrino mixing. The analysis is performed first in the context of Quantum Mechanics, and then for the case of Quantum Field Theory.

On entanglement in neutrino mixing and oscillations

Energy Technology Data Exchange (ETDEWEB)

Blasone, Massimo; Dell' Anno, Fabio; De Siena, Silvio; Illuminati, Fabrizio, E-mail: blasone@sa.infn.i [Dipartimento di Matematica e Informatica, Universita degli Studi di Salerno, Via Ponte don Melillo, I-84084 Fisciano (Italy)

2010-06-01

We report on recent results about entanglement in the context of particle mixing and oscillations. We study in detail single-particle entanglement arising in two-flavor neutrino mixing. The analysis is performed first in the context of Quantum Mechanics, and then for the case of Quantum Field Theory.

THE INFLUENCE OF BENZENE AS A TRACE REACTANT IN TITAN AEROSOL ANALOGS

Energy Technology Data Exchange (ETDEWEB)

Trainer, Melissa G. [Planetary Environments Laboratory, Code 699, NASA Goddard Space Flight Center, Greenbelt, MD 20771 (United States); Sebree, Joshua A. [NASA Postdoctoral Program Fellow, Code 699, Goddard Space Flight Center, Greenbelt, MD 20771 (United States); Heidi Yoon, Y.; Tolbert, Margaret A., E-mail: melissa.trainer@nasa.gov [Cooperative Institute for Research in Environmental Sciences, University of Colorado at Boulder, Box 216 UCB, Boulder, CO 80309 (United States)

2013-03-20

Benzene has been detected in Titan's atmosphere by Cassini instruments, with concentrations ranging from sub-ppb in the stratosphere to ppm in the ionosphere. Sustained levels of benzene in the haze formation region could signify that it is an important reactant in the formation of Titan's organic aerosol. To date, there have not been laboratory investigations to assess the influence of benzene on aerosol properties. We report a laboratory study on the chemical composition of organic aerosol formed from C{sub 6}H{sub 6}/CH{sub 4}/N{sub 2} via far ultraviolet irradiation (120-200 nm). The compositional results are compared to those from aerosol generated by a more ''traditional Titan'' mixture of CH{sub 4}/N{sub 2}. Our results show that even a trace amount of C{sub 6}H{sub 6} (10 ppm) has significant impact on the chemical composition and production rates of organic aerosol. There are several pathways by which photolyzed benzene may react to form larger molecules, both with and without the presence of CH{sub 4}, but many of these reaction mechanisms are only beginning to be explored for the conditions at Titan. Continued work investigating the influence of benzene in aerosol growth will advance understanding of this previously unstudied reaction system.

Use of Gas Transported Reactants for Uranium Remediation in Vadose Zone Sediments

International Nuclear Information System (INIS)

Szecsody, James E.; Zhong, Lirong; Truex, Michael J.; Resch, Charles T.; Williams, Mark D.

2010-01-01

This laboratory-scale investigation is focused on decreasing mobility of uranium in subsurface contaminated sediments in the vadose zone by in situ geochemical manipulation at low water content. This geochemical manipulation of the sediment surface phases included reduction, pH change (acidic and alkaline), and additions of chemicals (phosphate, ferric iron) to form specific precipitates. Reactants were advected into 1-D columns packed with Hanford 200 area U-contaminated sediment as a reactive gas (for CO2, NH3, H2S, SO2), with a 0.1% water content mist (for NaOH, Fe(III), HCl, PO4) and with a 1% water content foam (for PO4). Because uranium is present in the sediment in multiple phases, changes in U surface phases were evaluated with a series of liquid extractions that dissolve progressively less soluble phases and electron microbe identification of mineral phases. In terms of the short-term decrease in U mobility (in decreasing order), NH3, NaOH mist, CO2, HCl mist, and Fe(III) mist showed 20% to 35% change in U surface phases. The two reductive gas treatments (H2S and SO2) showed little change. For long-term decrease in U transport, mineral phases created that had low solubility (phosphates, silicates) were desired, so NH3, phosphates (mist and foam delivered), and NaOH mist showed the greatest formation of these minerals.

Metal-doped single-walled carbon nanotubes and production thereof

Science.gov (United States)

Dillon, Anne C.; Heben, Michael J.; Gennett, Thomas; Parilla, Philip A.

2007-01-09

Metal-doped single-walled carbon nanotubes and production thereof. The metal-doped single-walled carbon nanotubes may be produced according to one embodiment of the invention by combining single-walled carbon nanotube precursor material and metal in a solution, and mixing the solution to incorporate at least a portion of the metal with the single-walled carbon nanotube precursor material. Other embodiments may comprise sputter deposition, evaporation, and other mixing techniques.

Effect of experimental factors on magnetic properties of nickel nanoparticles produced by chemical reduction method using a statistical design

International Nuclear Information System (INIS)

Vaezi, M.R.; Barzgar Vishlaghi, M.; Farzalipour Tabriz, M.; Mohammad Moradi, O.

2015-01-01

Highlights: • Superparamagnetic nickel nanoparticles are synthesized by wet chemical reduction. • Effects of synthesis parameters on magnetic properties are studied. • Central composite experimental design is used for building an empirical model. • Solvents ratio was more influential than reactants mixing rate. - Abstract: Nickel nanoparticles were synthesized by chemical reduction method in the absence of any surface capping agent. The effect of reactants mixing rate and the volume ratio of methanol/ethanol as solvent on the morphology and magnetic properties of nickel nanoparticles were studied by design of experiment using central composite design. X-ray diffraction (XRD) technique and Transmission Electron Microscopy (TEM) were utilized to characterize the synthesized nanoparticles. Size distribution of particles was studied by Dynamic Light Scattering (DLS) technique and magnetic properties of produced nanoparticles were investigated by Vibrating Sample Magnetometer (VSM) apparatus. The results showed that the magnetic properties of nickel nanoparticles were more influenced by volume ratio of methanol/ethanol than the reactants mixing rate. Super-paramagnetic nickel nanoparticles with size range between 20 and 50 nm were achieved when solvent was pure methanol and the reactants mixing rate was kept at 70 ml/h. But addition of more ethanol to precursor solvent leads to the formation of larger particles with broader size distribution and weak ferromagnetic or super-paramagnetic behavior

Metal Catalysts for Heterogeneous Catalysis: From Single Atoms to Nanoclusters and Nanoparticles.

Science.gov (United States)

Liu, Lichen; Corma, Avelino

2018-05-23

Metal species with different size (single atoms, nanoclusters, and nanoparticles) show different catalytic behavior for various heterogeneous catalytic reactions. It has been shown in the literature that many factors including the particle size, shape, chemical composition, metal-support interaction, and metal-reactant/solvent interaction can have significant influences on the catalytic properties of metal catalysts. The recent developments of well-controlled synthesis methodologies and advanced characterization tools allow one to correlate the relationships at the molecular level. In this Review, the electronic and geometric structures of single atoms, nanoclusters, and nanoparticles will be discussed. Furthermore, we will summarize the catalytic applications of single atoms, nanoclusters, and nanoparticles for different types of reactions, including CO oxidation, selective oxidation, selective hydrogenation, organic reactions, electrocatalytic, and photocatalytic reactions. We will compare the results obtained from different systems and try to give a picture on how different types of metal species work in different reactions and give perspectives on the future directions toward better understanding of the catalytic behavior of different metal entities (single atoms, nanoclusters, and nanoparticles) in a unifying manner.

Integrating reaction and analysis: investigation of higher-order reactions by cryogenic trapping

Directory of Open Access Journals (Sweden)

Skrollan Stockinger

2013-09-01

Full Text Available A new approach for the investigation of a higher-order reaction by on-column reaction gas chromatography is presented. The reaction and the analytical separation are combined in a single experiment to investigate the Diels–Alder reaction of benzenediazonium-2-carboxylate as a benzyne precursor with various anthracene derivatives, i.e. anthracene, 9-bromoanthracene, 9-anthracenecarboxaldehyde and 9-anthracenemethanol. To overcome limitations of short reaction contact times at elevated temperatures a novel experimental setup was developed involving a cooling trap to achieve focusing and mixing of the reactants at a defined spot in a fused-silica capillary. This trap functions as a reactor within the separation column in the oven of a gas chromatograph. The reactants are sequentially injected to avoid undefined mixing in the injection port. An experimental protocol was developed with optimized injection intervals and cooling times to achieve sufficient conversions at short reaction times. Reaction products were rapidly identified by mass spectrometric detection. This new approach represents a practical procedure to investigate higher-order reactions at an analytical level and it simultaneously provides valuable information for the optimization of the reaction conditions.

The Case for Mixed-Age Grouping in Early Education.

Science.gov (United States)

Katz, Lilian G.; And Others

In six brief chapters, mixed-age grouping of young children in schools and child care centers is explored and advocated. Chapter 1 defines mixed-age grouping, examines limitations of single-age grouping, and points out positive characteristics of mixed-age classes. Chapter 2 discusses social development as seen in children's interactions in…

A correlation for single phase turbulent mixing in square rod arrays under highly turbulent conditions

International Nuclear Information System (INIS)

Jeong, Hae Yong; Ha, Kwi Seok; Kwon, Young Min; Chang, Won Pyo; Lee, Yong Bum

2006-01-01

The existing experimental data related to the turbulent mixing factor in rod arrays is examined and a new definition of the turbulent mixing factor is introduced to take into account the turbulent mixing of fluids with various Prandtl numbers. The new definition of the mixing factor is based on the eddy diffusivity of energy. With this definition of the mixing factor, it was found that the geometrical parameter, δ ij /D h , correlates the turbulent mixing data better than S/d, which has been used frequently in existing correlations. Based on the experimental data for a highly turbulent condition in square rod arrays, a correlation describing turbulent mixing dependent on the parameter δ ij /D h has been developed. The correlation is insensitive to the Re number and it takes into account the effect of the turbulent Prandtl number. The proposed correlation predicts a reasonable mixing even at a lower S/d ratio

KBr-Li Br and KBr-LiBr doped with Ti mixed single crystal by Czochralski method and glow curve studies

International Nuclear Information System (INIS)

Faripour, H.; Faripour, N.

2003-01-01

Mixed-single Crystals: pure KBr-LiBr and KBr-LiBr with Ti dopant were grown by Czochralski method. Because of difference between lattice parameters of KBr and LiBr, the growth speed of crystals were relatively low, and they were annealed in a special temperature condition providing some cleavages. They were exposed by β radiation and the glow curve was analysed for each crystal. Analysing of glow curve, showed that Ti impurity has been the curves of main peak curve appearance temperature decreasing

Raman spectroscopy of isotopically pure ({sup 12}C, {sup 13}C) and isotopically mixed ({sup 12.5}C) diamond single crystals at ultrahigh pressures

Energy Technology Data Exchange (ETDEWEB)

Enkovich, P. V., E-mail: enkovich@hppi.troitsk.ru; Brazhkin, V. V.; Lyapin, S. G.; Novikov, A. P. [Russian Academy of Sciences, Troitsk, Institute for High-Pressure Physics (Russian Federation); Kanda, H. [National Institute for Materials Science (Japan); Stishov, S. M. [Russian Academy of Sciences, Troitsk, Institute for High-Pressure Physics (Russian Federation)

2016-09-15

The Raman scattering by isotopically pure {sup 12}C and {sup 13}C diamond single crystals and by isotopically mixed {sup 12.5}C diamond single crystals is studied at a high accuracy. The studies are performed over a wide pressure range up to 73 GPa using helium as a hydrostatic pressure-transferring medium. It is found that the quantum effects, which determine the difference between the ratio of the Raman scattering frequencies in the {sup 12}C and {sup 13}C diamonds and the classical ratio (1.0408), increase to 30 GPa and then decrease. Thus, inversion in the sign of the quantum contribution to the physical properties of diamond during compression is detected. Our data suggest that the maximum possible difference between the bulk moduli of the {sup 12}C and {sup 13}C diamonds is 0.15%. The investigation of the isotopically mixed {sup 12.5}C diamond shows that the effective mass, which determines the Raman frequency, decreases during compression from 12.38 au at normal pressure to 12.33 au at 73 GPa.

Highly efficient quenching of tris(2,2'-bipyridyl)ruthenium(II) electrochemiluminescence by ozone using formaldehyde, methylglyoxal, and glyoxalate as co-reactants and its application to ozone sensing.

Science.gov (United States)

Gao, Ying; Liu, Xiaoyun; Qi, Wenjing; Gao, Wenyue; Li, Yunhui; Xu, Guobao

2015-06-21

Most electrochemiluminescence (ECL) systems require high concentrations of quencher to totally quench ECL. In this study, we found that ozone can quench tris(2,2'-bipyridyl)ruthenium(II) ECL using formaldehyde, methylglyoxal, or glyoxalate as co-reactants at a glassy carbon electrode with remarkable efficiencies even when the concentration of ozone is merely 0.25% of that of the co-reactant. The strongest quenching is observed with the tris(2,2'-bipyridyl)ruthenium(II)/formaldehyde ECL system. The tris(2,2'-bipyridyl)ruthenium(II)/formaldehyde ECL intensities decrease linearly with the ozone concentration over the range of 0.025-25 μM (r = 0.9947) with a limit of detection of 8 nM. The method is more sensitive and faster than most methods. It shows high selectivity in the presence of other ROS or oxidants and some metal ions, such as H2O2, ClO(-), Mg(2+), Ni(2+), etc. The method exhibits high recoveries for the detection of ozone in a ventilated photocopy room.

A Comparison and Integration of MiSeq and MinION Platforms for Sequencing Single Source and Mixed Mitochondrial Genomes.

Directory of Open Access Journals (Sweden)

Michael R Lindberg

Full Text Available Single source and multiple donor (mixed samples of human mitochondrial DNA were analyzed and compared using the MinION and the MiSeq platforms. A generalized variant detection strategy was employed to provide a cursory framework for evaluating the reliability and accuracy of mitochondrial sequences produced by the MinION. The feasibility of long-read phasing was investigated to establish its efficacy in quantitatively distinguishing and deconvolving individuals in a mixture. Finally, a proof-of-concept was demonstrated by integrating both platforms in a hybrid assembly that leverages solely mixture data to accurately reconstruct full mitochondrial genomes.

The intrinsic role of nanoconfinement in chemical equilibrium: evidence from DNA hybridization.

Science.gov (United States)

Rubinovich, Leonid; Polak, Micha

2013-05-08

Recently we predicted that when a reaction involving a small number of molecules occurs in a nanometric-scale domain entirely segregated from the surrounding media, the nanoconfinement can shift the position of equilibrium toward products via reactant-product reduced mixing. In this Letter, we demonstrate how most-recently reported single-molecule fluorescence measurements of partial hybridization of ssDNA confined within nanofabricated chambers provide the first experimental confirmation of this entropic nanoconfinement effect. Thus, focusing separately on each occupancy-specific equilibrium constant, quantitatively reveals extra stabilization of the product upon decreasing the chamber occupancy or size. Namely, the DNA hybridization under nanoconfined conditions is significantly favored over the identical reaction occurring in bulk media with the same reactant concentrations. This effect, now directly verified for DNA, can be relevant to actual biological processes, as well as to diverse reactions occurring within molecular capsules, nanotubes, and other functional nanospaces.

Sensitivity of Cirrus and Mixed-phase Clouds to the Ice Nuclei Spectra in McRAS-AC: Single Column Model Simulations

Science.gov (United States)

Betancourt, R. Morales; Lee, D.; Oreopoulos, L.; Sud, Y. C.; Barahona, D.; Nenes, A.

2012-01-01

The salient features of mixed-phase and ice clouds in a GCM cloud scheme are examined using the ice formation parameterizations of Liu and Penner (LP) and Barahona and Nenes (BN). The performance of LP and BN ice nucleation parameterizations were assessed in the GEOS-5 AGCM using the McRAS-AC cloud microphysics framework in single column mode. Four dimensional assimilated data from the intensive observation period of ARM TWP-ICE campaign was used to drive the fluxes and lateral forcing. Simulation experiments where established to test the impact of each parameterization in the resulting cloud fields. Three commonly used IN spectra were utilized in the BN parameterization to described the availability of IN for heterogeneous ice nucleation. The results show large similarities in the cirrus cloud regime between all the schemes tested, in which ice crystal concentrations were within a factor of 10 regardless of the parameterization used. In mixed-phase clouds there are some persistent differences in cloud particle number concentration and size, as well as in cloud fraction, ice water mixing ratio, and ice water path. Contact freezing in the simulated mixed-phase clouds contributed to transfer liquid to ice efficiently, so that on average, the clouds were fully glaciated at T approximately 260K, irrespective of the ice nucleation parameterization used. Comparison of simulated ice water path to available satellite derived observations were also performed, finding that all the schemes tested with the BN parameterization predicted 20 average values of IWP within plus or minus 15% of the observations.

CFD analysis of supercritical water flow and heat transfer in single channel with mixing vane

International Nuclear Information System (INIS)

Zuo Guoping; Xie Hongyan; Yu Tao

2012-01-01

Three-dimensional rectangular channel with the mixing wane in supercritical water reactor is investigated with CFX. The mixing vane elevation influenced on temperature distribution and flow field are simulated in the model. The results showed the mixing vane cause fluid circumferential flow, making flow hot and cold fluids mixed and fluid temperature uniform distribution, effectively improve the fuel rod surface temperature distribution and reduced hot temperature. Among the mixing wing elevation of 15, 30, 45, 50, 60 and 70 angle, the 30 angle is the best case in improving temperature distribution. (authors)

Why, and how, mixed methods research is undertaken in health services research in England: a mixed methods study

Science.gov (United States)

O'Cathain, Alicia; Murphy, Elizabeth; Nicholl, Jon

2007-01-01

Background Recently, there has been a surge of international interest in combining qualitative and quantitative methods in a single study – often called mixed methods research. It is timely to consider why and how mixed methods research is used in health services research (HSR). Methods Documentary analysis of proposals and reports of 75 mixed methods studies funded by a research commissioner of HSR in England between 1994 and 2004. Face-to-face semi-structured interviews with 20 researchers sampled from these studies. Results 18% (119/647) of HSR studies were classified as mixed methods research. In the documentation, comprehensiveness was the main driver for using mixed methods research, with researchers wanting to address a wider range of questions than quantitative methods alone would allow. Interviewees elaborated on this, identifying the need for qualitative research to engage with the complexity of health, health care interventions, and the environment in which studies took place. Motivations for adopting a mixed methods approach were not always based on the intrinsic value of mixed methods research for addressing the research question; they could be strategic, for example, to obtain funding. Mixed methods research was used in the context of evaluation, including randomised and non-randomised designs; survey and fieldwork exploratory studies; and instrument development. Studies drew on a limited number of methods – particularly surveys and individual interviews – but used methods in a wide range of roles. Conclusion Mixed methods research is common in HSR in the UK. Its use is driven by pragmatism rather than principle, motivated by the perceived deficit of quantitative methods alone to address the complexity of research in health care, as well as other more strategic gains. Methods are combined in a range of contexts, yet the emerging methodological contributions from HSR to the field of mixed methods research are currently limited to the single

Atomic layer deposition of Ru thin film using N{sub 2}/H{sub 2} plasma as a reactant

Energy Technology Data Exchange (ETDEWEB)

Hong, Tae Eun [Busan Center, Korea Basic Science Institute, 1275 Jisadong, Gangseogu, Busan, 618-230 (Korea, Republic of); Mun, Ki-Yeung; Choi, Sang-Kyung; Park, Ji-Yoon [School of Materials Science and Engineering Yeungnam University 214-1, Dae-dong, Gyeongsan-si, Gyeongsangbuk-do, 712-749 (Korea, Republic of); Kim, Soo-Hyun, E-mail: soohyun@ynu.ac.kr [School of Materials Science and Engineering Yeungnam University 214-1, Dae-dong, Gyeongsan-si, Gyeongsangbuk-do, 712-749 (Korea, Republic of); Cheon, Taehoon [Center for Core Research Facilities, Daegu Gyeongbuk Institute of Science and Technology, Sang-ri, Hyeonpung-myeon, Dalseong-gun, Daegu (Korea, Republic of); Kim, Woo Kyoung [School of Chemical Engineering, Yeungnam University, 214-1, Dae-dong, Gyeongsan-si, Gyeongsangbuk-do, 712-749 (Korea, Republic of); Lim, Byoung-Yong; Kim, Sunjung [School of Materials Science and Engineering, University of Ulsan, Mugeo-dong, Nam-go, Ulsan, 680-749 (Korea, Republic of)

2012-07-31

Ruthenium (Ru) thin films were grown by atomic layer deposition using IMBCHRu [({eta}6-1-Isopropyl-4-MethylBenzene)({eta}4-CycloHexa-1,3-diene)Ruthenium(0)] as a precursor and a nitrogen-hydrogen mixture (N{sub 2}/H{sub 2}) plasma as a reactant, at the substrate temperature of 270 Degree-Sign C. In the wide range of the ratios of N{sub 2} and total gas flow rates (fN{sub 2}/N{sub 2} + H{sub 2}) from 0.12 to 0.70, pure Ru films with negligible nitrogen incorporation of 0.5 at.% were obtained, with resistivities ranging from {approx} 20 to {approx} 30 {mu} Ohm-Sign cm. A growth rate of 0.057 nm/cycle and negligible incubation cycle for the growth on SiO{sub 2} was observed, indicating the fast nucleation of Ru. The Ru films formed polycrystalline and columnar grain structures with a hexagonal-close-packed phase. Its resistivity was dependent on the crystallinity, which could be controlled by varying the deposition parameters such as plasma power and pulsing time. Cu was electroplated on a 10-nm-thick Ru film. Interestingly, it was found that the nitrogen could be incorporated into Ru at a higher reactant gas ratio of 0.86. The N-incorporated Ru film ({approx} 20 at.% of N) formed a nanocrystalline and non-columnar grain structure with the resistivity of {approx} 340 {mu} Ohm-Sign cm. - Highlights: Black-Right-Pointing-Pointer Atomic layer deposition (ALD) of Ru and N-incorporated Ru film using N{sub 2}/H{sub 2} plasma. Black-Right-Pointing-Pointer The growth rate of 0.057 nm/cycle and negligible incubation cycle. Black-Right-Pointing-Pointer A low resistivity of Ru ({approx} 16.5 {mu} Ohm-Sign cm) at the deposition temperature of 270 Degree-Sign C. Black-Right-Pointing-Pointer Electroplating of Cu on a 10-nm-thick ALD-Ru film.

A continuous flow microfluidic calorimeter: 3-D numerical modeling with aqueous reactants

International Nuclear Information System (INIS)

Sen, Mehmet A.; Kowalski, Gregory J.; Fiering, Jason; Larson, Dale

2015-01-01

Highlights: • A co-flow microreactor is modeled in flow, reaction/diffusion, and thermal domains. • Analysis shows how arrayed temperature sensors can provide enthalpy of reaction. • Optical plasmonic temperature sensors could be arrayed suitably for calorimetry. • The reactor studied has a volume of 25 nL. - Abstract: A computational analysis of the reacting flow field, species diffusion and heat transfer processes with thermal boundary layer effects in a microchannel reactor with a coflow configuration was performed. Two parallel adjacent streams of aqueous reactants flow along a wide, shallow, enclosed channel in contact with a substrate, which is affixed to a temperature controlled plate. The Fluent computational fluid dynamics package solved the Navier–Stokes, mass transport and energy equations. The energy model, including the enthalpy of reaction as a nonuniform heat source, was validated by calculating the energy balance at several control volumes in the microchannel. Analysis reveals that the temperature is nearly uniform across the channel thickness, in the direction normal to the substrate surface; hence, measurements made by sensors at or near the surface are representative of the average temperature. Additionally, modeling the channel with a glass substrate and a silicone cover shows that heat transfer is predominantly due to the glass substrate. Finally, using the numerical results, we suggest that a microcalorimeter could be based on this configuration, and that temperature sensors such as optical nanohole array sensors could have sufficient spatial resolution to determine enthalpy of reaction

A continuous flow microfluidic calorimeter: 3-D numerical modeling with aqueous reactants

Energy Technology Data Exchange (ETDEWEB)

Sen, Mehmet A., E-mail: mehmet.sen@mathworks.com [Northeastern University, Department of Mechanical and Industrial Engineering, 360 Hungtington Avenue, 334 Snell Engineering Center, Boston, MA 02115 (United States); Kowalski, Gregory J., E-mail: gkowal@coe.neu.edu [Northeastern University, Department of Mechanical and Industrial Engineering, 360 Hungtington Avenue, 334 Snell Engineering Center, Boston, MA 02115 (United States); Fiering, Jason, E-mail: jfiering@draper.com [Charles Stark Draper Laboratory, 555 Technology Square, Cambridge, MA 02139 (United States); Larson, Dale, E-mail: dlarson@draper.com [Charles Stark Draper Laboratory, 555 Technology Square, Cambridge, MA 02139 (United States)

2015-03-10

Highlights: • A co-flow microreactor is modeled in flow, reaction/diffusion, and thermal domains. • Analysis shows how arrayed temperature sensors can provide enthalpy of reaction. • Optical plasmonic temperature sensors could be arrayed suitably for calorimetry. • The reactor studied has a volume of 25 nL. - Abstract: A computational analysis of the reacting flow field, species diffusion and heat transfer processes with thermal boundary layer effects in a microchannel reactor with a coflow configuration was performed. Two parallel adjacent streams of aqueous reactants flow along a wide, shallow, enclosed channel in contact with a substrate, which is affixed to a temperature controlled plate. The Fluent computational fluid dynamics package solved the Navier–Stokes, mass transport and energy equations. The energy model, including the enthalpy of reaction as a nonuniform heat source, was validated by calculating the energy balance at several control volumes in the microchannel. Analysis reveals that the temperature is nearly uniform across the channel thickness, in the direction normal to the substrate surface; hence, measurements made by sensors at or near the surface are representative of the average temperature. Additionally, modeling the channel with a glass substrate and a silicone cover shows that heat transfer is predominantly due to the glass substrate. Finally, using the numerical results, we suggest that a microcalorimeter could be based on this configuration, and that temperature sensors such as optical nanohole array sensors could have sufficient spatial resolution to determine enthalpy of reaction.

The mixing of fluids

International Nuclear Information System (INIS)

Ottino, J.M.

1989-01-01

What do the eruption of Krakatau, the manufacture of puff pastry and the brightness of stars have in common? Each involves some aspect of mixing. Mixing also plays a critical role in modern technology. Chemical engineers rely on mixing to ensure that substances react properly, to produce polymer blends that exhibit unique properties and to disperse drag-reducing agents in pipelines. Yet in spite of its of its ubiquity in nature and industry, mixing is only imperfectly under-stood. Indeed, investigators cannot even settle on a common terminology: mixing is often referred to as stirring by oceanographers and geophysicists, as blending by polymer engineers and as agitation by process engineers. Regardless of what the process is called, there is little doubt that it is exceedingly complex and is found in a great variety of systems. In constructing a theory of fluid mixing, for example, one has to take into account fluids that can be miscible or partially miscible and reactive or inert, and flows that are slow and orderly or very fast and turbulent. It is therefore not surprising that no single theory can explain all aspect of mixing in fluids and that straightforward computations usually fail to capture all the important details. Still, both physical experiments and computer simulations can provide insight into the mixing process. Over the past several years the authors and his colleague have taken both approaches in an effort to increase understanding of various aspect of the process-particularly of mixing involving slow flows and viscous fluids such as oils

Novel high explosive compositions

Science.gov (United States)

Perry, D.D.; Fein, M.M.; Schoenfelder, C.W.

1968-04-16

This is a technique of preparing explosive compositions by the in-situ reaction of polynitroaliphatic compounds with one or more carboranes or carborane derivatives. One or more polynitroaliphatic reactants are combined with one or more carborane reactants in a suitable container and mixed to a homogeneous reaction mixture using a stream of inert gas or conventional mixing means. Ordinarily the container is a fissure, crack, or crevice in which the explosive is to be implanted. The ratio of reactants will determine not only the stoichiometry of the system, but will effect the quality and quantity of combustion products, the explosive force obtained as well as the impact sensitivity. The test values can shift with even relatively slight changes or modifications in the reaction conditions. Eighteen illustrative examples accompany the disclosure. (46 claims)

Applications of mixed-methods methodology in clinical pharmacy research.

Science.gov (United States)

Hadi, Muhammad Abdul; Closs, S José

2016-06-01

Introduction Mixed-methods methodology, as the name suggests refers to mixing of elements of both qualitative and quantitative methodologies in a single study. In the past decade, mixed-methods methodology has gained popularity among healthcare researchers as it promises to bring together the strengths of both qualitative and quantitative approaches. Methodology A number of mixed-methods designs are available in the literature and the four most commonly used designs in healthcare research are: the convergent parallel design, the embedded design, the exploratory design, and the explanatory design. Each has its own unique advantages, challenges and procedures and selection of a particular design should be guided by the research question. Guidance on designing, conducting and reporting mixed-methods research is available in the literature, so it is advisable to adhere to this to ensure methodological rigour. When to use it is best suited when the research questions require: triangulating findings from different methodologies to explain a single phenomenon; clarifying the results of one method using another method; informing the design of one method based on the findings of another method, development of a scale/questionnaire and answering different research questions within a single study. Two case studies have been presented to illustrate possible applications of mixed-methods methodology. Limitations Possessing the necessary knowledge and skills to undertake qualitative and quantitative data collection, analysis, interpretation and integration remains the biggest challenge for researchers conducting mixed-methods studies. Sequential study designs are often time consuming, being in two (or more) phases whereas concurrent study designs may require more than one data collector to collect both qualitative and quantitative data at the same time.

Mixed Methods in Biomedical and Health Services Research

OpenAIRE

Curry, Leslie A.; Krumholz, Harlan M.; O’Cathain, Alicia; Plano Clark, Vicki L.; Cherlin, Emily; Bradley, Elizabeth H.

2013-01-01

Mixed methods studies, in which qualitative and quantitative methods are combined in a single program of inquiry, can be valuable in biomedical and health services research, where the complementary strengths of each approach can yield greater insight into complex phenomena than either approach alone. Although interest in mixed methods is growing among science funders and investigators, written guidance on how to conduct and assess rigorous mixed methods studies is not readily accessible to th...

The reactants equation of state for the tri-amino-tri-nitro-benzene (TATB) based explosive PBX 9502

Science.gov (United States)

Aslam, Tariq D.

2017-07-01

The response of high explosives (HEs), due to mechanical and/or thermal insults, is of great importance for both safety and performance. A major component of how an HE responds to these stimuli stems from its reactant equation of state (EOS). Here, the tri-amino-tri-nitro-benzene based explosive PBX 9502 is investigated by examining recent experiments. Furthermore, a complete thermal EOS is calibrated based on the functional form devised by Wescott, Stewart, and Davis [J. Appl. Phys. 98, 053514 (2005)]. It is found, by comparing to earlier calibrations, that a variety of thermodynamic data are needed to sufficiently constrain the EOS response over a wide range of thermodynamic state space. Included in the calibration presented here is the specific heat as a function of temperature, isobaric thermal expansion, and shock Hugoniot response. As validation of the resulting model, isothermal compression and isentropic compression are compared with recent experiments.

Single-reactor process for producing liquid-phase organic compounds from biomass

Science.gov (United States)

Dumesic, James A [Verona, WI; Simonetti, Dante A [Middleton, WI; Kunkes, Edward L [Madison, WI

2011-12-13

Disclosed is a method for preparing liquid fuel and chemical intermediates from biomass-derived oxygenated hydrocarbons. The method includes the steps of reacting in a single reactor an aqueous solution of a biomass-derived, water-soluble oxygenated hydrocarbon reactant, in the presence of a catalyst comprising a metal selected from the group consisting of Cr, Mn, Fe, Co, Ni, Cu, Mo, Tc, Ru, Rh, Pd, Ag, W, Re, Os, Ir, Pt, and Au, at a temperature, and a pressure, and for a time sufficient to yield a self-separating, three-phase product stream comprising a vapor phase, an organic phase containing linear and/or cyclic mono-oxygenated hydrocarbons, and an aqueous phase.

Evaluation of mixing downstream of tees in duct systems with respect to single point representative air sampling.

Science.gov (United States)

Kim, Taehong; O'Neal, Dennis L; Ortiz, Carlos

2006-09-01

Air duct systems in nuclear facilities must be monitored with continuous sampling in case of an accidental release of airborne radionuclides. The purpose of this work is to identify the air sampling locations where the velocity and contaminant concentrations fall below the 20% coefficient of variation required by the American National Standards Institute/Health Physics Society N13.1-1999. Experiments of velocity and tracer gas concentration were conducted on a generic "T" mixing system which included combinations of three sub ducts, one main duct, and air velocities from 0.5 to 2 m s (100 to 400 fpm). The experimental results suggest that turbulent mixing provides the accepted velocity coefficients of variation after 6 hydraulic diameters downstream of the T-junction. About 95% of the cases achieved coefficients of variation below 10% by 6 hydraulic diameters. However, above a velocity ratio (velocity in the sub duct/velocity in the main duct) of 2, velocity profiles were uniform in a shorter distance downstream of the T-junction as the velocity ratio went up. For the tracer gas concentration, the distance needed for the coefficients of variation to drop 20% decreased with increasing velocity ratio due to the sub duct airflow momentum. The results may apply to other duct systems with similar geometries and, ultimately, be a basis for selecting a proper sampling location under the requirements of single point representative sampling.

Agent-based simulation of reactions in the crowded and structured intracellular environment: Influence of mobility and location of the reactants

Directory of Open Access Journals (Sweden)

Lapin Alexei

2011-05-01

Full Text Available Abstract Background In this paper we apply a novel agent-based simulation method in order to model intracellular reactions in detail. The simulations are performed within a virtual cytoskeleton enriched with further crowding elements, which allows the analysis of molecular crowding effects on intracellular diffusion and reaction rates. The cytoskeleton network leads to a reduction in the mobility of molecules. Molecules can also unspecifically bind to membranes or the cytoskeleton affecting (i the fraction of unbound molecules in the cytosol and (ii furthermore reducing the mobility. Binding of molecules to intracellular structures or scaffolds can in turn lead to a microcompartmentalization of the cell. Especially the formation of enzyme complexes promoting metabolic channeling, e.g. in glycolysis, depends on the co-localization of the proteins. Results While the co-localization of enzymes leads to faster reaction rates, the reduced mobility decreases the collision rate of reactants, hence reducing the reaction rate, as expected. This effect is most prominent in diffusion limited reactions. Furthermore, anomalous diffusion can occur due to molecular crowding in the cell. In the context of diffusion controlled reactions, anomalous diffusion leads to fractal reaction kinetics. The simulation framework is used to quantify and separate the effects originating from molecular crowding or the reduced mobility of the reactants. We were able to define three factors which describe the effective reaction rate, namely f diff for the diffusion effect, f volume for the crowding, and f access for the reduced accessibility of the molecules. Conclusions Molecule distributions, reaction rate constants and structural parameters can be adjusted separately in the simulation allowing a comprehensive study of individual effects in the context of a realistic cell environment. As such, the present simulation can help to bridge the gap between in vivo and in vitro

Comparison of single and mixed ion implantation effects on the changes of the surface hardness, light transmittance, and electrical conductivity of polymeric materials

International Nuclear Information System (INIS)

Park, J. W.; Lee, J. H.; Lee, J. S.; Kil, J. G.; Choi, B. H.; Han, Z. H.

2001-01-01

Single or mixed ions of N, He, C were implanted onto the transparent PET(Polyethylen Terephtalate) with the ion energies of less than 100 keV and the surface hardness, light transmittance and electrical conductivity were examined. As measured with nanoindentation, mixed ion implantations such as N + +He + or N + + C + exhibited more increase in the surface hardness than the single ion implantation. Especially, implantation of C+N ions increased the surface hardness by about three times as compared to the implantation of N ion alone, which means more than 10 times increase than the untreated PET. Surface electrical conductivity was increased along with the hardness increase. The conductivity increase was more proportional to the hardness when used the higher ion energy and ion dose, while it did not show any relationship at as low as 50 keV of ion energy. The light at the 550 nm wavelength (visual range) transmitted more than 85%, which is close to that of as-received PET, and at the wavelength below 300 nm(UV range) the rays were absorbed more than 95% as traveling through the sheet, implying that there are processing parameters which the ion implanted PET maintains the transparency and absorbs the UV rays

Assessing the Concordance between Child Reports and Adult Observations of Single and Mixed Emotion in Children's Drawings of Themselves or Another Child

Science.gov (United States)

Burkitt, Esther

2018-01-01

The present study assessed concordance between child reported and adult observed strategies to depict single and mixed emotion in the same human figure drawings. 205 children (104 boys, 101 girls) aged 6 years 2 months to 8 years 3 months formed two age groups (6 years 2 months-7 years 2 months and 7 years 3 months-8 years 3 months) across two…

Mixed beams for the nuclear microprobe

Energy Technology Data Exchange (ETDEWEB)

Saint, A.; Breese, M.B.H.; Legge, G.L.F. [Melbourne Univ., Parkville, VIC (Australia). School of Physics

1996-12-31

Recently the Micro-Analytical Research Centre (MARC) at Melbourne University has developed a technique to provide mixed beams of ions for a magnetically focussed nuclear microprobe. Such a mixed beam is defined as two (or more) beams of different species ions that can quickly and easily be made to have the same magnetic rigidity R{sub m} = (mE/q{sup 2}) and therefore be transported, focused and scanned the same in a magnetic nuclear microprobe. The production of mixed beams in an electrostatically focussed micro- probe have already been demonstrated. This paper will show how mixed beams can be produced on a single-ended accelerator. Indications of how to produce them on a tandem will also be given. Applications of these mixed beams in micro-lithography, scanning transmission ion microscopy (STIM) imaging and ion beam induced charge (IBIC) imaging will also be presented. 3 refs., 3 figs.

Mixed beams for the nuclear microprobe

Energy Technology Data Exchange (ETDEWEB)

Saint, A; Breese, M B.H.; Legge, G L.F. [Melbourne Univ., Parkville, VIC (Australia). School of Physics

1997-12-31

Recently the Micro-Analytical Research Centre (MARC) at Melbourne University has developed a technique to provide mixed beams of ions for a magnetically focussed nuclear microprobe. Such a mixed beam is defined as two (or more) beams of different species ions that can quickly and easily be made to have the same magnetic rigidity R{sub m} = (mE/q{sup 2}) and therefore be transported, focused and scanned the same in a magnetic nuclear microprobe. The production of mixed beams in an electrostatically focussed micro- probe have already been demonstrated. This paper will show how mixed beams can be produced on a single-ended accelerator. Indications of how to produce them on a tandem will also be given. Applications of these mixed beams in micro-lithography, scanning transmission ion microscopy (STIM) imaging and ion beam induced charge (IBIC) imaging will also be presented. 3 refs., 3 figs.

Reflections on Mixing Methods in Applied Linguistics Research

Science.gov (United States)

Hashemi, Mohammad R.

2012-01-01

This commentary advocates the use of mixed methods research--that is the integration of qualitative and quantitative methods in a single study--in applied linguistics. Based on preliminary findings from a research project in progress, some reflections on the current practice of mixing methods as a new trend in applied linguistics are put forward.…

Single and mixed formulations of inoculants with diazotrophic bacteria, under different nitrogen rates and on the paddy rice crop

Directory of Open Access Journals (Sweden)

Paula Bianchet

2013-12-01

Full Text Available The use of diazotrophic bacteria as a biological input for the production of paddy rice can reduce nitrogen fertilizer applications and contribute to plant development. The use of mixed inoculants’ formulations can increase the efficiency of nitrogen fixation biological process. The objective of this study was to evaluate the effect of single and mixed formulations of inoculants with diazotrophic bacteria on the initial growth of paddy rice plants under different levels of N. The experiment was set in a greenhouse. Treatments consisted of four types of inoculation (no inoculation, inoculation with the isolated AI UDESC 27, inoculation with the isolated FE UDESC 22, and inoculation with the mixed formulation of isolated AI UDESC UDESC 27 and FE UDESC 22; and two levels of mineral nitrogen (30 and 60 mg kg-1 of N. The cultivar used was Epagri 109, which presents late maturity (over 140 days and high yield potential. Treatments were arranged in a factorial design (4 x 2 with five replicates. The experimental design was completely randomized. Inoculation with diazotrophic bacteria reduced by 18% and 26% shoot and root dry matter of rice plants, respectively. Plants also presented lower root area and volume when they were inoculated. There was no significant effect of inoculation and nitrogen rates on the number of leaves and tillers produced per plant or shoot nitrogen accumulation. The results showed that the isolated used in this work were not effective to stimulate shoot and root growth of cv Epagri 109, regardless of formulation type and rate of N.

Image quality optimization and evaluation of linearly mixed images in dual-source, dual-energy CT

International Nuclear Information System (INIS)

Yu Lifeng; Primak, Andrew N.; Liu Xin; McCollough, Cynthia H.

2009-01-01

In dual-source dual-energy CT, the images reconstructed from the low- and high-energy scans (typically at 80 and 140 kV, respectively) can be mixed together to provide a single set of non-material-specific images for the purpose of routine diagnostic interpretation. Different from the material-specific information that may be obtained from the dual-energy scan data, the mixed images are created with the purpose of providing the interpreting physician a single set of images that have an appearance similar to that in single-energy images acquired at the same total radiation dose. In this work, the authors used a phantom study to evaluate the image quality of linearly mixed images in comparison to single-energy CT images, assuming the same total radiation dose and taking into account the effect of patient size and the dose partitioning between the low-and high-energy scans. The authors first developed a method to optimize the quality of the linearly mixed images such that the single-energy image quality was compared to the best-case image quality of the dual-energy mixed images. Compared to 80 kV single-energy images for the same radiation dose, the iodine CNR in dual-energy mixed images was worse for smaller phantom sizes. However, similar noise and similar or improved iodine CNR relative to 120 kV images could be achieved for dual-energy mixed images using the same total radiation dose over a wide range of patient sizes (up to 45 cm lateral thorax dimension). Thus, for adult CT practices, which primarily use 120 kV scanning, the use of dual-energy CT for the purpose of material-specific imaging can also produce a set of non-material-specific images for routine diagnostic interpretation that are of similar or improved quality relative to single-energy 120 kV scans.

Physiological effects of diet mixing on consumer fitness: a meta-analysis.

Science.gov (United States)

Lefcheck, Jonathan S; Whalen, Matthew A; Davenport, Theresa M; Stone, Joshua P; Duffy, J Emmett

2013-03-01

The degree of dietary generalism among consumers has important consequences for population, community, and ecosystem processes, yet the effects on consumer fitness of mixing food types have not been examined comprehensively. We conducted a meta-analysis of 161 peer-reviewed studies reporting 493 experimental manipulations of prey diversity to test whether diet mixing enhances consumer fitness based on the intrinsic nutritional quality of foods and consumer physiology. Averaged across studies, mixed diets conferred significantly higher fitness than the average of single-species diets, but not the best single prey species. More than half of individual experiments, however, showed maximal growth and reproduction on mixed diets, consistent with the predicted benefits of a balanced diet. Mixed diets including chemically defended prey were no better than the average prey type, opposing the prediction that a diverse diet dilutes toxins. Finally, mixed-model analysis showed that the effect of diet mixing was stronger for herbivores than for higher trophic levels. The generally weak evidence for the nutritional benefits of diet mixing in these primarily laboratory experiments suggests that diet generalism is not strongly favored by the inherent physiological benefits of mixing food types, but is more likely driven by ecological and environmental influences on consumer foraging.

TRAFFIC SIMULATION FOR MIXED TRAFFIC SYSTEMS

African Journals Online (AJOL)

EGETE

2012-05-04

May 4, 2012 ... Traffic problem is classified into single and mixed, especially in most developing countries, where motorbikes are ..... The traffic light control system presented by its location on ... multi-destination dynamic routing and real-time.

Glycerol transesterification with ethyl acetate to synthesize acetins using ethyl acetate as reactant and entrainer

Directory of Open Access Journals (Sweden)

Amin Shafiei

2017-03-01

Full Text Available Transesterification of glycerol with ethyl acetate was performed over acidic catalysts in the batch and semi-batch systems. Ethyl acetate was used as reactant and entrainer to remove the produced ethanol during the reaction, through azeotrope formation. Since the azeotrope of ethyl acetate and ethanol forms at 70 oC, all the experiments were performed at this temperature. Para-toluene sulfonic acid, sulfuric acid, and Amberlyst 36 were used as catalyst. The effect of process parameters including ethyl acetate to glycerol molar ratio (6-12, reaction time (3-9 h, and the catalyst to glycerol weight (2.5-9.0%, on the conversion and products selectivities were investigated. Under reflux conditions, 100% glycerol conversion was obtained with 45%, 44%, and 11% selectivity to monoacetin, diacetin, and triacetin, respectively. Azeotropic reactive distillation led to 100% conversion of glycerol with selectivities of 3%, 48% and 49% for monoacetin, diacetin, and triacetin. During the azeotropic reactive distillation, it was possible to remove ethanol to shift the equilibrium towards diacetin and triacetin. Therefore, the total selectivity to diacetin and triacetin was increased from 55% to 97% through azeotropic distillation.

A new method to manipulate broiler chicken growth and metabolism: Response to mixed LED light system

Science.gov (United States)

Yang, Yefeng; Yu, Yonghua; Pan, Jinming; Ying, Yibin; Zhou, Hong

2016-05-01

Present study introduced a new method to manipulate broiler chicken growth and metabolism by mixing the growth-advantage LED. We found that the green/blue LED mixed light system (G-B and G × B) have the similar stimulatory effect on chick body weight with single green light and single blue light (G and B), compared with normal artificial light (P = 0.028). Moreover, the percentage of carcass was significantly greater in the mixed light (G × B) when compared with the single light (P = 0.003). Synchronized with body weight, the mixed light (G-B and G × B) had a significant improved influence on the feed conversion of birds compared with normal light (P = 0.002). A significant improvement in feed conversion were found in mixed light (G × B) compared with single LED light (P = 0.037). G group resulted in a greater high-density lipoprotein cholesterol level than B group (P = 0.002), whereas B group resulted in a greater low-density lipoprotein cholesterol level than G group (P = 0.017). The mixed light significantly increased the birds’ glucose level in comparison with the single light (P = 0.003). This study might establish an effective strategy for maximizing growth of chickens by mixed LED technology.

Experimental studies of Z-pinches of mixed wire array with aluminum and tungsten

International Nuclear Information System (INIS)

Ning Cheng; Li Zhenghong; Hua Xinsheng; Xu Rongkun; Peng Xianjue; Xu Zeping; Yang Jianlun; Guo Cun; Jiang Shilun; Feng Shuping; Yang Libing; Yan Chengli; Song Fengjun; Smirnov, V.P.; Kalinin, Yu.G.; Kingsep, A.S.; Chernenko, A.S.; Grabovsky, E.V.

2004-01-01

In the form of joint experiment between China and Russia, the experimental studies of Z-pinches of mixed wire array of aluminum (A1) and tungsten (W) were carried out on S-300 generator, which was located on Kurchatov Institute of Russia. The experimental results were compared with those of single A1 array and single W array, respectively. There are obvious difference between mixed one and single one in their photon spectral distributions. The intensity of K-series emission lines from the mixed wire array Z-pinch is lower than that from single A1 array. The radiated lines with wavelengths less than 1.6 nm were not found in single W array Z-pinches. In the Z-pinch processes, the area radiating x-rays in mixed wire array is smaller than that of single A1 array, but is slightly lower than that from single W array. The FWHM of x-ray pulse with a maximal power 0.3-0.5 TW and total energy 10-20 kJ is about 25 ns, which radiated from Z-pinches with a radial convergence of 4-5 on S-300 generator. The shadow photograph of the mixed wire-array Z-pinch plasma by laser probe shows that the core-corona configuration was formed and the corona was moving toward the center axis during the wire-array plasma formation, that the interface of the plasma is not clear, and that there are a number structures inside. They also suggests that there was an obvious development of Magneto Rayleigh-Taylor instability in the Z-pinch process as well

Cosmeceutical potentials and bioactive compounds of rice bran fermented with single and mix culture of Aspergillus oryzae and Rhizopus oryzae

Directory of Open Access Journals (Sweden)

Dang Lelamurni Abd Razak

2017-04-01

Full Text Available In the present study, rice bran, one of the most abundant agricultural by-products in Malaysia, was fermented with single and mixed cultures of Aspergillus oryzae and Rhizopus oryzae. The fermented rice bran extracts were tested for their functional properties and compared to the non-fermented counterparts. Antioxidant activities as well as phenolics and organic acid contents were evaluated. Skincare-related functionalities were also tested by evaluating tyrosinase and elastase inhibition activities. Tyrosinase inhibition activity, measured to determine the anti-pigmentation effect of extracts, was found to be the highest in the extract of rice bran fermented with A. oryzae (56.18% compared to other extracts. In determining the anti-aging effect of fermented rice bran extracts, the same extract showed the highest elastase inhibition activity with a value of 60.52%. Antioxidant activities were found to be highest in the mix-cultured rice bran extract. The results of phenolic and organic acid content were varied; the major phenolic acid detected was ferulic acid with a value of 43.19 μg/ml in the mix-cultured rice bran extract. On the other hand, citric acid was the major organic acid detected, with the highest content found in the same extract (214.6 mg/g. The results of this study suggest that the fermented rice bran extracts may have the potential to be further exploited as ingredients in cosmetics as well as in antioxidant-rich products.

Atmospheric pressure flow reactor: Gas phase chemical kinetics under tropospheric conditions without wall effects

Science.gov (United States)

Koontz, Steven L. (Inventor); Davis, Dennis D. (Inventor)

1991-01-01

A flow reactor for simulating the interaction in the troposphere is set forth. A first reactant mixed with a carrier gas is delivered from a pump and flows through a duct having louvers therein. The louvers straighten out the flow, reduce turbulence and provide laminar flow discharge from the duct. A second reactant delivered from a source through a pump is input into the flowing stream, the second reactant being diffused through a plurality of small diffusion tubes to avoid disturbing the laminar flow. The commingled first and second reactants in the carrier gas are then directed along an elongated duct where the walls are spaced away from the flow of reactants to avoid wall interference, disturbance or turbulence arising from the walls. A probe connected with a measuring device can be inserted through various sampling ports in the second duct to complete measurements of the first and second reactants and the product of their reaction at selected XYZ locations relative to the flowing system.

The Case for Mixed-Age Grouping in Early Childhood Education Programs.

Science.gov (United States)

Katz, Lilian G.; And Others

The seven brief chapters of this paper advocate mixed-age grouping in schools and child care centers. Discussion defines mixed-age grouping and examines some limitations of single-age grouping. Research findings on social and cognitive aspects of mixed-age grouping are reviewed. Social aspects are discussed by considering in turn the following…

Short wave infrared hyperspectral imaging for recovered post-consumer single and mixed polymers characterization

Science.gov (United States)

Bonifazi, Giuseppe; Palmieri, Roberta; Serranti, Silvia

2015-03-01

Postconsumer plastics from packing and packaging represent about the 60% of the total plastic wastes (i.e. 23 million of tons) produced in Europe. The EU Directive (2014/12/EC) fixes as target that the 60%, by weight, of packaging waste has to be recovered, or thermally valorized. When recovered, the same directive established that packaging waste has to be recycled in a percentage ranging between 55% (minimum) and 60% (maximum). The non-respect of these rules can produce that large quantities of end-of-life plastic products, specifically those utilized for packaging, are disposed-off, with a strong environmental impact. The application of recycling strategies, finalized to polymer recovery, can represent an opportunity to reduce: i) not renewable raw materials (i.e. oil) utilization, ii) carbon dioxide emissions and iii) amount of plastic waste disposed-off. Aim of this work was to perform a full characterization of different end-of-life polymers based products, constituted not only by single polymers but also of mixtures, in order to realize their identification for quality control and/or certification assessment. The study was specifically addressed to characterize the different recovered products as resulting from a recycling plant where classical processing flow-sheets, based on milling, classification and separation, are applied. To reach this goal, an innovative sensing technique, based on the utilization of a HyperSpectral[b] I[/b]maging (HSI) device working in the SWIR region (1000-2500 nm), was investigated. Following this strategy, single polymers and/or mixed polymers recovered were correctly recognized. The main advantage of the proposed approach is linked to the possibility to perform "on-line" analyses, that is directly on the different material flow streams, as resulting from processing, without any physical sampling and classical laboratory "off-line" determination.

Method for solid state crystal growth

Science.gov (United States)

Nolas, George S.; Beekman, Matthew K.

2013-04-09

A novel method for high quality crystal growth of intermetallic clathrates is presented. The synthesis of high quality pure phase crystals has been complicated by the simultaneous formation of both clathrate type-I and clathrate type-II structures. It was found that selective, phase pure, single-crystal growth of type-I and type-II clathrates can be achieved by maintaining sufficient partial pressure of a chemical constituent during slow, controlled deprivation of the chemical constituent from the primary reactant. The chemical constituent is slowly removed from the primary reactant by the reaction of the chemical constituent vapor with a secondary reactant, spatially separated from the primary reactant, in a closed volume under uniaxial pressure and heat to form the single phase pure crystals.

The behavior of exciplex decay processes and interplay of radiationless transition and preliminary reorganization mechanisms of electron transfer in loose and tight pairs of reactants.

Science.gov (United States)

Kuzmin, Michael G; Soboleva, Irina V; Dolotova, Elena V

2007-01-18

Exciplex emission spectra and rate constants of their decay via internal conversion and intersystem crossing are studied and discussed in terms of conventional radiationless transition approach. Exciplexes of 9-cyanophenanthrene with 1,2,3-trimethoxybenzene and 1,3,5-trimethoxybenzene were studied in heptane, toluene, butyl acetate, dichloromethane, butyronitrile, and acetonitrile. A better description of spectra and rate constants is obtained using 0-0 transition energy and Gauss broadening of vibrational bands rather than the free energy of electron transfer and reorganization energy. The coincidence of parameters describing exciplex emission spectra and dependence of exciplex decay rate constants on energy gap gives the evidence of radiationless quantum transition mechanism rather than thermally activated medium reorganization mechanism of charge recombination in exciplexes and excited charge transfer complexes (contact radical ion pairs) as well as in solvent separated radical ion pairs. Radiationless quantum transition mechanism is shown to provide an appropriate description also for the main features of exergonic excited-state charge separation reactions if fast mutual transformations of loose and tight pairs of reactants are considered. In particular, very fast electron transfer (ET) in tight pairs of reactants with strong electronic coupling of locally excited and charge transfer states can prevent the observation of an inverted region in bimolecular excited-state charge separation even for highly exergonic reactions.

Quantification of African cassava mosaic virus (ACMV) and East African cassava mosaic virus (EACMV-UG) in single and mixed infected Cassava (Manihot esculenta Crantz) using quantitative PCR.

Science.gov (United States)

Naseem, Saadia; Winter, Stephan

2016-01-01

The quantity of genomic DNA-A and DNA-B of African cassava mosaic virus (ACMV) and East African cassava mosaic virus Uganda (Uganda variant, EACMV-UG) was analysed using quantitative PCR to assess virus concentrations in plants from susceptible and tolerant cultivars. The concentrations of genome components in absolute and relative quantification experiments in single and mixed viral infections were determined. Virus concentration was much higher in symptomatic leaf tissues compared to non-symptomatic leaves and corresponded with the severity of disease symptoms. In general, higher titres were recorded for EACMV-UG Ca055 compared to ACMV DRC6. The quantitative assessment also showed that the distribution of both viruses in the moderately resistant cassava cv. TMS 30572 was not different from the highly susceptible cv. TME 117. Natural mixed infections with both viruses gave severe disease symptoms. Relative quantification of virus genomes in mixed infections showed higher concentrations of EACMV-UG DNA-A compared to ACMV DNA-A, but a marked reduction of EACMV-UG DNA-B. The higher concentrations of EACMV-UG DNA-B compared to EACMV DNA-A accumulation in single infections were consistent. Since DNA-B is implicated in virus cell-to-cell spread and systemic movement, the abundance of the EACMV-UG DNA-B may be an important factor driving cassava mosaic disease epidemic. Copyright © 2015 Elsevier B.V. All rights reserved.

Probing Intranuclear Environments at the Single-Molecule Level

Science.gov (United States)

Grünwald, David; Martin, Robert M.; Buschmann, Volker; Bazett-Jones, David P.; Leonhardt, Heinrich; Kubitscheck, Ulrich; Cardoso, M. Cristina

2008-01-01

Genome activity and nuclear metabolism clearly depend on accessibility, but it is not known whether and to what extent nuclear structures limit the mobility and access of individual molecules. We used fluorescently labeled streptavidin with a nuclear localization signal as an average-sized, inert protein to probe the nuclear environment. The protein was injected into the cytoplasm of mouse cells, and single molecules were tracked in the nucleus with high-speed fluorescence microscopy. We analyzed and compared the mobility of single streptavidin molecules in structurally and functionally distinct nuclear compartments of living cells. Our results indicated that all nuclear subcompartments were easily and similarly accessible for such an average-sized protein, and even condensed heterochromatin neither excluded single molecules nor impeded their passage. The only significant difference was a higher frequency of transient trappings in heterochromatin, which lasted only tens of milliseconds. The streptavidin molecules, however, did not accumulate in heterochromatin, suggesting comparatively less free volume. Interestingly, the nucleolus seemed to exclude streptavidin, as it did many other nuclear proteins, when visualized by conventional fluorescence microscopy. The tracking of single molecules, nonetheless, showed no evidence for repulsion at the border but relatively unimpeded passage through the nucleolus. These results clearly show that single-molecule tracking can provide novel insights into mobility of proteins in the nucleus that cannot be obtained by conventional fluorescence microscopy. Our results suggest that nuclear processes may not be regulated at the level of physical accessibility but rather by local concentration of reactants and availability of binding sites. PMID:18065482

Incorporation of chemical kinetic models into process control

International Nuclear Information System (INIS)

Herget, C.J.; Frazer, J.W.

1981-01-01

An important consideration in chemical process control is to determine the precise rationing of reactant streams, particularly when a large time delay exists between the mixing of the reactants and the measurement of the product. In this paper, a method is described for incorporating chemical kinetic models into the control strategy in order to achieve optimum operating conditions. The system is first characterized by determining a reaction rate surface as a function of all input reactant concentrations over a feasible range. A nonlinear constrained optimization program is then used to determine the combination of reactants which produces the specified yield at minimum cost. This operating condition is then used to establish the nominal concentrations of the reactants. The actual operation is determined through a feedback control system employing a Smith predictor. The method is demonstrated on a laboratory bench scale enzyme reactor

Mixed mobile ion effect in fluorozincate glasses

International Nuclear Information System (INIS)

Ghosh, S; Ghosh, A

2005-01-01

The mixed mobile ion effect has been investigated for the first time in zinc fluoride glasses where in addition to alkali cations fluorine anions also participate in the diffusion process, unlike mixed alkali oxide glasses. The minimum in the conductivity, conductivity relaxation frequency, crossover frequency and decoupling index indicates the existence of the mixed mobile ion effect in these fluoride glasses. It has been observed that the non-exponential parameter and the frequency exponent are independent of temperature. It has been established that alkali ions and fluorine anions exhibit lower dimensionality of the conduction pathways in mixed alkali zinc fluoride glasses than that in the single alkali lithium based zinc fluoride glasses while they are migrating. From the scaling of the conductivity spectra, it has been established that the relaxation dynamics in mixed alkali zinc fluoride glasses is independent of temperature and composition

Internal validation of STRmix™ for the interpretation of single source and mixed DNA profiles.

Science.gov (United States)

Moretti, Tamyra R; Just, Rebecca S; Kehl, Susannah C; Willis, Leah E; Buckleton, John S; Bright, Jo-Anne; Taylor, Duncan A; Onorato, Anthony J

2017-07-01

The interpretation of DNA evidence can entail analysis of challenging STR typing results. Genotypes inferred from low quality or quantity specimens, or mixed DNA samples originating from multiple contributors, can result in weak or inconclusive match probabilities when a binary interpretation method and necessary thresholds (such as a stochastic threshold) are employed. Probabilistic genotyping approaches, such as fully continuous methods that incorporate empirically determined biological parameter models, enable usage of more of the profile information and reduce subjectivity in interpretation. As a result, software-based probabilistic analyses tend to produce more consistent and more informative results regarding potential contributors to DNA evidence. Studies to assess and internally validate the probabilistic genotyping software STRmix™ for casework usage at the Federal Bureau of Investigation Laboratory were conducted using lab-specific parameters and more than 300 single-source and mixed contributor profiles. Simulated forensic specimens, including constructed mixtures that included DNA from two to five donors across a broad range of template amounts and contributor proportions, were used to examine the sensitivity and specificity of the system via more than 60,000 tests comparing hundreds of known contributors and non-contributors to the specimens. Conditioned analyses, concurrent interpretation of amplification replicates, and application of an incorrect contributor number were also performed to further investigate software performance and probe the limitations of the system. In addition, the results from manual and probabilistic interpretation of both prepared and evidentiary mixtures were compared. The findings support that STRmix™ is sufficiently robust for implementation in forensic laboratories, offering numerous advantages over historical methods of DNA profile analysis and greater statistical power for the estimation of evidentiary weight, and

The single-particle mixing state and cloud scavenging of black carbon: a case study at a high-altitude mountain site in southern China

Science.gov (United States)

Zhang, Guohua; Lin, Qinhao; Peng, Long; Bi, Xinhui; Chen, Duohong; Li, Mei; Li, Lei; Brechtel, Fred J.; Chen, Jianxin; Yan, Weijun; Wang, Xinming; Peng, Ping'an; Sheng, Guoying; Zhou, Zhen

2017-12-01

In the present study, a ground-based counterflow virtual impactor (GCVI) was used to sample cloud droplet residual (cloud RES) particles, while a parallel PM2.5 inlet was used to sample cloud-free or cloud interstitial (cloud INT) particles. The mixing state of black carbon (BC)-containing particles and the mass concentrations of BC in the cloud-free, RES and INT particles were investigated using a single-particle aerosol mass spectrometer (SPAMS) and two aethalometers, respectively, at a mountain site (1690 m a. s. l. ) in southern China. The measured BC-containing particles were extensively internally mixed with sulfate and were scavenged into cloud droplets (with number fractions of 0.05-0.45) to a similar (or slightly lower) extent as all the measured particles (0.07-0.6) over the measured size range of 0.1-1.6 µm. The results indicate the preferential activation of larger particles and/or that the production of secondary compositions shifts the BC-containing particles towards larger sizes. BC-containing particles with an abundance of both sulfate and organics were scavenged less than those with sulfate but limited organics, implying the importance of the mixing state on the incorporation of BC-containing particles into cloud droplets. The mass scavenging efficiency of BC with an average of 33 % was similar for different cloud events independent of the air mass. This is the first time that both the mixing state and cloud scavenging of BC in China have been reported. Our results would improve the knowledge on the concentration, mixing state, and cloud scavenging of BC in the free troposphere.

Progress in the development of the MARBLE platform for studying thermonuclear burn in the presence of heterogeneous mix on OMEGA and the National Ignition Facility

Science.gov (United States)

Murphy, T. J.; Douglas, M. R.; Fincke, J. R.; Olson, R. E.; Cobble, J. A.; Haines, B. M.; Hamilton, C. E.; Lee, M. N.; Oertel, J. A.; Parra-Vasquez, N. A. G.; Randolph, R. B.; Schmidt, D. W.; Shah, R. C.; Smidt, J. M.; Tregillis, I. L.

2016-05-01

Mix of ablator material into fuel of an ICF capsule adds non-burning material, diluting the fuel and reducing burn. The amount of the reduction is dependent in part on the morphology of the mix. A probability distribution function (PDF) burn model has been developed [6] that utilizes the average concentration of mixed materials as well as the variance in this quantity across cells provided by the BHR turbulent transport model [3] and its revisions [4] to describe the mix in terms of a PDF of concentrations of fuel and ablator material, and provides the burn rate in mixed material. Work is underway to develop the MARBLE ICF platform for use on the National Ignition Facility in experiments to quantify the influence of heterogeneous mix on fusion burn. This platform consists of a plastic (CH) capsule filled with a deuterated plastic foam (CD) with a density of a few tens of milligrams per cubic centimeter, with tritium gas filling the voids in the foam. This capsule will be driven using x-ray drive on NIF, and the resulting shocks will induce turbulent mix that will result in the mixing of deuterium from the foam with the tritium gas. In order to affect the morphology of the mix, engineered foams with voids of diameter up to 100 microns will be utilized. The degree of mix will be determined from the ratio of DT to DD neutron yield. As the mix increases, the yield from reactions between the deuterium of the CD foam with tritium from the gas will increase. The ratio of DT to DD neutrons will be compared to a variation of the PDF burn model that quantifies reactions from initially separated reactants.

Effect of mixed and single crops on disease suppressiveness of soils

NARCIS (Netherlands)

Hiddink, G.A.; Termorshuizen, A.J.; Raaijmakers, J.M.; Bruggen, van A.H.C.

2005-01-01

The effect of mixed cropping on disease suppressiveness of soils was tested for two cropping systems, Brussels sprouts¿barley and triticale¿white clover. Disease suppressiveness of field soils was evaluated in bioassays for the soilborne pathogens Rhizoctonia solani, Fusarium oxysporum f. sp. lini,

Quark-lepton universality and large leptonic mixing

International Nuclear Information System (INIS)

Joshipura, Anjan S.; Smirnov, A.Yu.

2006-01-01

A unified description of fermionic mixing is proposed which assumes that in certain basis (i) a single complex unitary matrix V diagonalizes mass matrices of all fermions to the leading order (ii) the SU(5) relation M d =M l T exists between the mass matrices of the down quarks and the charged leptons, and (iii) M d - bar =M d . These assumptions automatically lead to different mixing patterns for quarks and leptons: Quarks remain unmixed to leading order (i.e. V CKM =1) while leptons have non-trivial mixing given by a symmetric unitary matrix V PMNS 0 =V T V. V depends on two physical mixing angles and for values of these angles ∼20 o -25 o it reproduces the observed mixing patterns rather well. We identify conditions under which the universal mixing V follows from the universal mass matrices of fermions. Relatively small perturbations to the leading order structure lead to the CKM mixing and corrections to V PMNS 0 . We find that if the correction matrix equals the CKM matrix, the resulting lepton mixing agrees well with data and predicts (V PMNS ) e3 >0.08

Group-Level EEG-Processing Pipeline for Flexible Single Trial-Based Analyses Including Linear Mixed Models.

Science.gov (United States)

Frömer, Romy; Maier, Martin; Abdel Rahman, Rasha

2018-01-01

Here we present an application of an EEG processing pipeline customizing EEGLAB and FieldTrip functions, specifically optimized to flexibly analyze EEG data based on single trial information. The key component of our approach is to create a comprehensive 3-D EEG data structure including all trials and all participants maintaining the original order of recording. This allows straightforward access to subsets of the data based on any information available in a behavioral data structure matched with the EEG data (experimental conditions, but also performance indicators, such accuracy or RTs of single trials). In the present study we exploit this structure to compute linear mixed models (LMMs, using lmer in R) including random intercepts and slopes for items. This information can easily be read out from the matched behavioral data, whereas it might not be accessible in traditional ERP approaches without substantial effort. We further provide easily adaptable scripts for performing cluster-based permutation tests (as implemented in FieldTrip), as a more robust alternative to traditional omnibus ANOVAs. Our approach is particularly advantageous for data with parametric within-subject covariates (e.g., performance) and/or multiple complex stimuli (such as words, faces or objects) that vary in features affecting cognitive processes and ERPs (such as word frequency, salience or familiarity), which are sometimes hard to control experimentally or might themselves constitute variables of interest. The present dataset was recorded from 40 participants who performed a visual search task on previously unfamiliar objects, presented either visually intact or blurred. MATLAB as well as R scripts are provided that can be adapted to different datasets.

Quark flavor mixing, CP violation, and all that

International Nuclear Information System (INIS)

Gilman, F.J.

1988-04-01

We review the present state of knowledge of the mixing of quark flavors under weak interactions and the associated explanation of CP violation inherent in the single nontrivial phase present in the three-generation mixing matrix. In this context we present the phenomenological basis for the increasing possibility that large CP violation asymmetries can be experimentally observed in the B meson system. 39 refs., 11 figs.,

Investigating the Differences of Single-Vehicle and Multivehicle Accident Probability Using Mixed Logit Model

Directory of Open Access Journals (Sweden)

Bowen Dong

2018-01-01

Full Text Available Road traffic accidents are believed to be associated with not only road geometric feature and traffic characteristic, but also weather condition. To address these safety issues, it is of paramount importance to understand how these factors affect the occurrences of the crashes. Existing studies have suggested that the mechanisms of single-vehicle (SV accidents and multivehicle (MV accidents can be very different. Few studies were conducted to examine the difference of SV and MV accident probability by addressing unobserved heterogeneity at the same time. To investigate the different contributing factors on SV and MV, a mixed logit model is employed using disaggregated data with the response variable categorized as no accidents, SV accidents, and MV accidents. The results indicate that, in addition to speed gap, length of segment, and wet road surfaces which are significant for both SV and MV accidents, most of other variables are significant only for MV accidents. Traffic, road, and surface characteristics are main influence factors of SV and MV accident possibility. Hourly traffic volume, inside shoulder width, and wet road surface are found to produce statistically significant random parameters. Their effects on the possibility of SV and MV accident vary across different road segments.

Observation of charm mixing at LHCb

CERN Multimedia

CERN. Geneva

2012-01-01

Meson-antimeson mixing has been observed in the K0−K0bar, B0−B0bar and B0s−B0sbar systems. Evidence of mixing in the charm system has been reported by three experiments using different D0 decay channels, but only the combination of these results provides confirmation of D0−D0bar mixing with more than 5σ significance. We report a measurement of charm mixing using the time-dependent ratio of D0 → K+π− to D0 → K−π+ decay rates in D∗+-tagged events reconstructed in 1.0 fb−1 of integrated luminosity recorded by the LHCb experiment in 2011. We measure the mixing parameters x'2 = (−0.9 ± 1.3) × 10−4, y' = (7.2 ± 2.4) × 10−3 and the ratio of doubly-Cabibbo-suppressed to Cabibbo-favored decay rates RD = (3.52 ± 0.15) × 10−3. The result excludes the no-mixing hypothesis with a probability corresponding to 9.1σ and represents the first observation of D0−D0bar oscillations from a single measurement.

Optical calorimetry in microfluidic droplets.

Science.gov (United States)

Chamoun, Jacob; Pattekar, Ashish; Afshinmanesh, Farzaneh; Martini, Joerg; Recht, Michael I

2018-05-29

A novel microfluidic calorimeter that measures the enthalpy change of reactions occurring in 100 μm diameter aqueous droplets in fluoropolymer oil has been developed. The aqueous reactants flow into a microfluidic droplet generation chip in separate fluidic channels, limiting contact between the streams until immediately before they form the droplet. The diffusion-driven mixing of reactants is predominantly restricted to within the droplet. The temperature change in droplets due to the heat of reaction is measured optically by recording the reflectance spectra of encapsulated thermochromic liquid crystals (TLC) that are added to one of the reactant streams. As the droplets travel through the channel, the spectral characteristics of the TLC represent the internal temperature, allowing optical measurement with a precision of ≈6 mK. The microfluidic chip and all fluids are temperature controlled, and the reaction heat within droplets raises their temperature until thermal diffusion dissipates the heat into the surrounding oil and chip walls. Position resolved optical temperature measurement of the droplets allows calculation of the heat of reaction by analyzing the droplet temperature profile over time. Channel dimensions, droplet generation rate, droplet size, reactant stream flows and oil flow rate are carefully balanced to provide rapid diffusional mixing of reactants compared to thermal diffusion, while avoiding thermal "quenching" due to contact between the droplets and the chip walls. Compared to conventional microcalorimetry, which has been used in this work to provide reference measurements, this new continuous flow droplet calorimeter has the potential to perform titrations ≈1000-fold faster while using ≈400-fold less reactants per titration.

Mixed-Methods Design in Biology Education Research: Approach and Uses

Science.gov (United States)

Warfa, Abdi-Rizak M.

2016-01-01

Educational research often requires mixing different research methodologies to strengthen findings, better contextualize or explain results, or minimize the weaknesses of a single method. This article provides practical guidelines on how to conduct such research in biology education, with a focus on mixed-methods research (MMR) that uses both…

Pressure drop and flow distribution characteristics of single and parallel serpentine flow fields for polymer electrolyte membrane fuel cells

International Nuclear Information System (INIS)

Baek, Seung Man; Kim, Charn Jung; Jeon, Dong Hyup; Nam, Jin Hyun

2012-01-01

This study numerically investigates pressure drop and flow distribution characteristics of serpentine flow fields (SFFs) that are designed for polymer electrolyte membrane fuel cells, which consider the Poiseuille flow with secondary pressure drop in the gas channel (GC) and the Darcy flow in the porous gas diffusion layer (GDL). The numerical results for a conventional SFF agreed well with those obtained via computational fluid dynamics simulations, thus proving the validity of the present flow network model. This model is employed to characterize various single and parallel SFFs, including multi-pass serpentine flow fields (MPSFFs). Findings reveal that under rib convection (convective flow through GDL under an interconnector rib) is an important transport process for conventional SFFs, with its intensity being significantly enhanced as GDL permeability increases. The results also indicate that under rib convection can be significantly improved by employing MPSFFs as the reactant flow field, because of the closely interlaced structure of GC regions that have different path lengths from the inlet. However, reactant flow rate through GCs proportionally decreases as under rib convection intensity increases, suggesting that proper optimization is required between the flow velocity in GCs and the under rib convection intensity in GDLs

Mixed-linker zeolitic imidazolate framework mixed-matrix membranes for aggressive CO2 separation from natural gas

KAUST Repository

Thompson, Joshua A.

2014-07-01

Zeolitic imidazolate framework (ZIF) materials are a promising subclass of metal-organic frameworks (MOF) for gas separations. However, due to the deleterious effects of gate-opening phenomena associated with organic linker rotation near the limiting pore apertures of ZIFs, there have been few demonstrations of improved gas separation properties over pure polymer membranes when utilizing ZIF materials in composite membranes for CO2-based gas separations. Here, we report a study of composite ZIF/polymer membranes, containing mixed-linker ZIF materials with ZIF-8 crystal topologies but composed of different organic linker compositions. Characterization of the mixed-linker ZIFs shows that the mixed linker approach offers control over the porosity and pore size distribution of the materials, as determined from nitrogen physisorption and Horváth-Kawazoe analysis. Single gas permeation measurements on mixed-matrix membranes reveal that inclusion of mixed-linker ZIFs yields membranes with better ideal CO2/CH4 selectivity than membranes containing ZIF-8. This improvement is shown to likely occur from enhancement in the diffusion selectivity of the membranes associated with controlling the pore size distribution of the ZIF filler. Mixed-gas permeation experiments show that membranes with mixed-linker ZIFs display an effective plasticization resistance that is not typical of the pure polymeric matrix. Overall, we demonstrate that mixed-linker ZIFs can improve the gas separation properties in composite membranes and may be applicable to aggressive CO2 concentrations in natural gas feeds. © 2013 Elsevier Inc. All rights reserved.

Sub-Ensemble Monitoring of DNA Strand Displacement Using Multiparameter Single-Molecule FRET.

Science.gov (United States)

Baltierra-Jasso, Laura E; Morten, Michael J; Magennis, Steven W

2018-03-05

Non-enzymatic DNA strand displacement is an important mechanism in dynamic DNA nanotechnology. Here, we show that the large parameter space that is accessible by single-molecule FRET is ideal for the simultaneous monitoring of multiple reactants and products of DNA strand exchange reactions. We monitored the strand displacement from double-stranded DNA (dsDNA) by single-stranded DNA (ssDNA) at 37 °C; the data were modelled as a second-order reaction approaching equilibrium, with a rate constant of 10 m -1  s -1 . We also followed the displacement from a DNA three-way junction (3WJ) by ssDNA. The presence of three internal mismatched bases in the middle of the invading strand did not prevent displacement from the 3WJ, but reduced the second-order rate constant by about 50 %. We attribute strand exchange in the dsDNA and 3WJ to a zero-toehold pathway from the blunt-ended duplex arms. The single-molecule approach demonstrated here will be useful for studying complex DNA networks. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Effects of balneotherapy on the reactants of acute inflammation phase in Ankylosing spondylitis

Directory of Open Access Journals (Sweden)

Stamenković Bojana

2009-01-01

Full Text Available Introduction. Ankylosing spondylitis (AS is a chronic inflammatory disease that affects sacroiliac joints, spinal column and peripheral joints. Beside medication therapy, physical and balneotherapy play an important role in its complex treatment. Objective. The aim of the research was to establish serum concentrations of C-reactive protein (CRP, α 1-acid glycoprotein (α 1-AGP, ceruloplasmine (CP and erythrocyte sedimentation rate (SE before and after the balneotherapy in ankylosing spondylitis. Methods. The research included 50 AS patients according to the revised New York criteria, of mean age 43 years, who were treated for 14 days on the average at the Clinic for Rheumatology of the Institute 'Niška Banja'. All the patients received medications and balneotherapy (radioactive oligomineral baths, peloid, massage, kinesitherapy; the serum concentrations of CRP, α1-AGP, CP and SE were measured before and after balneotherapy. Serum proteins were determined using original Nor Partigen plates Boehringer. Erythrocyte sedimentation rate was measured by Westergreen method. Balneotherapy was applied individually, intensively or mildly, depending on the AS stage and activity phase. Results. After dosed balneotherapy, a significant decrease in the concentrations of CP (p<0.05, α1-AGP (p<0.01 and CRP (p<0.05 was registered in the serums of AS patients. ESR was not significantly reduced. Conclusion. The research proved that α 1-acid glycoprotein, ceruloplasmine and C-reactive protein represent more sensitive inflammation markers as compared to erythrocyte sedimentation rate. The identification of acute phase reactants is important in the evaluation of dosed balneotherapy efficiency in the treatment of ankylosing spondylitis.

Scalar Glueball-Quarkonium Mixing and the Structure of the QCD Vacuum

CERN Document Server

Ellis, Jonathan Richard; Kharzeev, Dima E

1999-01-01

We use Ward identities of broken scale invariance to infer the amount of scalar glueball--$\\bar{q}q$ meson mixing from the ratio of quark and gluon condensates in the QCD vacuum. Assuming dominance by a single scalar state, as suggested by a phase-shift analysis, we find a mixing angle $\\gamma \\sim 36^{\\circ}$, corresponding to near-maximal mixing of the glueball and

Simulating mixed-phase Arctic stratus clouds: sensitivity to ice initiation mechanisms

Directory of Open Access Journals (Sweden)

G. McFarquhar

2009-07-01

Full Text Available The importance of Arctic mixed-phase clouds on radiation and the Arctic climate is well known. However, the development of mixed-phase cloud parameterization for use in large scale models is limited by lack of both related observations and numerical studies using multidimensional models with advanced microphysics that provide the basis for understanding the relative importance of different microphysical processes that take place in mixed-phase clouds. To improve the representation of mixed-phase cloud processes in the GISS GCM we use the GISS single-column model coupled to a bin resolved microphysics (BRM scheme that was specially designed to simulate mixed-phase clouds and aerosol-cloud interactions. Using this model with the microphysical measurements obtained from the DOE ARM Mixed-Phase Arctic Cloud Experiment (MPACE campaign in October 2004 at the North Slope of Alaska, we investigate the effect of ice initiation processes and Bergeron-Findeisen process (BFP on glaciation time and longevity of single-layer stratiform mixed-phase clouds. We focus on observations taken during 9–10 October, which indicated the presence of a single-layer mixed-phase clouds. We performed several sets of 12-h simulations to examine model sensitivity to different ice initiation mechanisms and evaluate model output (hydrometeors' concentrations, contents, effective radii, precipitation fluxes, and radar reflectivity against measurements from the MPACE Intensive Observing Period. Overall, the model qualitatively simulates ice crystal concentration and hydrometeors content, but it fails to predict quantitatively the effective radii of ice particles and their vertical profiles. In particular, the ice effective radii are overestimated by at least 50%. However, using the same definition as used for observations, the effective radii simulated and that observed were more comparable. We find that for the single-layer stratiform mixed-phase clouds simulated, process

Simulating mixed-phase Arctic stratus clouds: sensitivity to ice initiation mechanisms

Science.gov (United States)

Sednev, I.; Menon, S.; McFarquhar, G.

2009-07-01

The importance of Arctic mixed-phase clouds on radiation and the Arctic climate is well known. However, the development of mixed-phase cloud parameterization for use in large scale models is limited by lack of both related observations and numerical studies using multidimensional models with advanced microphysics that provide the basis for understanding the relative importance of different microphysical processes that take place in mixed-phase clouds. To improve the representation of mixed-phase cloud processes in the GISS GCM we use the GISS single-column model coupled to a bin resolved microphysics (BRM) scheme that was specially designed to simulate mixed-phase clouds and aerosol-cloud interactions. Using this model with the microphysical measurements obtained from the DOE ARM Mixed-Phase Arctic Cloud Experiment (MPACE) campaign in October 2004 at the North Slope of Alaska, we investigate the effect of ice initiation processes and Bergeron-Findeisen process (BFP) on glaciation time and longevity of single-layer stratiform mixed-phase clouds. We focus on observations taken during 9-10 October, which indicated the presence of a single-layer mixed-phase clouds. We performed several sets of 12-h simulations to examine model sensitivity to different ice initiation mechanisms and evaluate model output (hydrometeors' concentrations, contents, effective radii, precipitation fluxes, and radar reflectivity) against measurements from the MPACE Intensive Observing Period. Overall, the model qualitatively simulates ice crystal concentration and hydrometeors content, but it fails to predict quantitatively the effective radii of ice particles and their vertical profiles. In particular, the ice effective radii are overestimated by at least 50%. However, using the same definition as used for observations, the effective radii simulated and that observed were more comparable. We find that for the single-layer stratiform mixed-phase clouds simulated, process of ice phase initiation

Nature of the magnetic ground state in the mixed valence compound CeRuSn: a single-crystal study

International Nuclear Information System (INIS)

Fikáček, J; Prokleška, J; Prchal, J; Custers, J; Sechovský, V

2013-01-01

We report on detailed low-temperature measurements of the magnetization, the specific heat and the electrical resistivity on high-quality CeRuSn single crystals. The compound orders antiferromagnetically at T N = 2.8 K with the Ce 3+ ions locked within the a–c plane of the monoclinic structure. Magnetization shows that below T N CeRuSn undergoes a metamagnetic transition when applying a magnetic field of 1.5 and 0.8 T along the a- and c-axis, respectively. This transition manifests in a tremendous negative jump of ∼25% in the magnetoresistance. The value of the saturated magnetization along the easy magnetization direction (c-axis) and the magnetic entropy above T N derived from specific heat data correspond to the scenario of only one third of the Ce ions in the compound being trivalent and carrying a stable Ce 3+ magnetic moment, whereas the other two thirds of the Ce ions are in a nonmagnetic tetravalent and/or mixed valence state. This is consistent with the low-temperature CeRuSn crystal structure i.e., a superstructure consisting of three unit cells of the CeCoAl type piled up along the c-axis, and in which the Ce 3+ ions are characterized by large distances from the Ru ligands while the Ce–Ru distances of the other Ce ions are much shorter causing a strong 4f-ligand hybridization and hence leading to tetravalent and/or mixed valence Ce ions. (paper)

ADVANCED MIXING MODELS

Energy Technology Data Exchange (ETDEWEB)

Lee, S; Dimenna, R; Tamburello, D

2011-02-14

The process of recovering and processing High Level Waste (HLW) the waste in storage tanks at the Savannah River Site (SRS) typically requires mixing the contents of the tank with one to four mixers (pumps) located within the tank. The typical criteria to establish a mixed condition in a tank are based on the number of pumps in operation and the time duration of operation. To ensure that a mixed condition is achieved, operating times are typically set conservatively long. This approach results in high operational costs because of the long mixing times and high maintenance and repair costs for the same reason. A significant reduction in both of these costs might be realized by reducing the required mixing time based on calculating a reliable indicator of mixing with a suitably validated computer code. The focus of the present work is to establish mixing criteria applicable to miscible fluids, with an ultimate goal of addressing waste processing in HLW tanks at SRS and quantifying the mixing time required to suspend sludge particles with the submersible jet pump. A single-phase computational fluid dynamics (CFD) approach was taken for the analysis of jet flow patterns with an emphasis on the velocity decay and the turbulent flow evolution for the farfield region from the pump. Literature results for a turbulent jet flow are reviewed, since the decay of the axial jet velocity and the evolution of the jet flow patterns are important phenomena affecting sludge suspension and mixing operations. The work described in this report suggests a basis for further development of the theory leading to the identified mixing indicators, with benchmark analyses demonstrating their consistency with widely accepted correlations. Although the indicators are somewhat generic in nature, they are applied to Savannah River Site (SRS) waste tanks to provide a better, physically based estimate of the required mixing time. Waste storage tanks at SRS contain settled sludge which varies in

Associated equilibria with participatian of single and mixed silver, lead and cadmium halide complexes in mixtures of molten alkali and alkaline earth metal nitrates

International Nuclear Information System (INIS)

Gouk, Kh.S.; Gupta, R.K.; Vekma, K.V.

1983-01-01

Associated equilibria in the systems, which contain single and mixed silver, cadmium and lead halide complexes in the KNO 3 -Ba(N0 3 ) 2 (87.6:12.4 and 89:11 mol.%) and NaNO 3 -Ba(NO 3 ) 2 (94.2-5.8 mol%) melts in the temperature range from 568.2 up to 698.2 K are investigated. Applicability of equations derivated on the base of quasi-lattice model to description of temperature coefficients of association constants is analized

Body-esteem of pupils who attended single-sex versus mixed-sex schools: a cross-sectional study of intrasexual competition and peer victimization.

Science.gov (United States)

Lereya, Suzet Tanya; Eryigit-Madzwamuse, Suna; Patra, Chanchala; Smith, Joshua H; Wolke, Dieter

2014-10-01

In intrasexual competition (competition for reproductive resources), bullying can be viewed as a tool to devalue competitors, gain a high status and a powerful, dominant position in the peer group which may lead to beneficial gains such as access to potential romantic partners. This study investigated the relationship between intrasexual competition, bullying victimization and body-esteem, in single-sex versus mixed-sex schools. 420 participants completed a body-esteem scale, a retrospective bullying questionnaire, and intrasexual competition scales. Our results showed that relational victimization was associated with low body-esteem for both females and males. Females in single-sex schools experienced higher intrasexual competition which in turn was associated with their body-esteem directly and indirectly via relational victimization. In males, intrasexual competition was indirectly associated with body-esteem via relational victimization. Interventions to improve body esteem may focus on reducing intrasexual competition and peer victimization. Copyright © 2014 The Foundation for Professionals in Services for Adolescents. Published by Elsevier Ltd. All rights reserved.

Mixed-Methods Design in Biology Education Research: Approach and Uses

Science.gov (United States)

Warfa, Abdi-Rizak M.

2016-01-01

Educational research often requires mixing different research methodologies to strengthen findings, better contextualize or explain results, or minimize the weaknesses of a single method. This article provides practical guidelines on how to conduct such research in biology education, with a focus on mixed-methods research (MMR) that uses both quantitative and qualitative inquiries. Specifically, the paper provides an overview of mixed-methods design typologies most relevant in biology education research. It also discusses common methodological issues that may arise in mixed-methods studies and ways to address them. The paper concludes with recommendations on how to report and write about MMR. PMID:27856556

Systematic analysis of the impact of mixing locality on Mixing-DAC linearity for multicarrier GSM

NARCIS (Netherlands)

Bechthum, E.; Radulov, G.I.; Briaire, J.; Geelen, G.; Roermund, van A.H.M.

2012-01-01

In an RF transmitter, the function of the mixer and the DAC can be combined in a single block: the Mixing-DAC. For the generation of multicarrier GSM signals in a basestation, high dynamic linearity is required, i.e. SFDR>85dBc, at high output signal frequency, i.e. ƒout ˜ 4GHz. This represents a

Chiral Selectivity in Inter-reactant Recognition and Electron Transfer of the Oxidation of Horse Heart Cytochrome c by Trioxalatocobaltate(III)

DEFF Research Database (Denmark)

Nazmutdinov, Renat R.; Bronshtein, Michael D.; Zinkicheva, Tamara T.

2016-01-01

We have studied electron transfer between cytochrome c and the chiral transition-metal complex pair Λ- and Δ-[Co(Ox)3]3− (Ox2− = oxalate) via strong ion-pair formation. Chirality was found in both ion-pair formation and electron transfer, with the Λ enantiomer the more strongly bound and faster r...... reacting. Investigations of the chirality using electron-transfer theory combined with quantum-chemical and statistical-mechanical calculations showed that chirality is solely in inter-reactant interaction and electronic overlap.......We have studied electron transfer between cytochrome c and the chiral transition-metal complex pair Λ- and Δ-[Co(Ox)3]3− (Ox2− = oxalate) via strong ion-pair formation. Chirality was found in both ion-pair formation and electron transfer, with the Λ enantiomer the more strongly bound and faster...

Realistic multisite lattice-gas modeling and KMC simulation of catalytic surface reactions: Kinetics and multiscale spatial behavior for CO-oxidation on metal (1 0 0) surfaces

Science.gov (United States)

Liu, Da-Jiang; Evans, James W.

2013-12-01

A realistic molecular-level description of catalytic reactions on single-crystal metal surfaces can be provided by stochastic multisite lattice-gas (msLG) models. This approach has general applicability, although in this report, we will focus on the example of CO-oxidation on the unreconstructed fcc metal (1 0 0) or M(1 0 0) surfaces of common catalyst metals M = Pd, Rh, Pt and Ir (i.e., avoiding regimes where Pt and Ir reconstruct). These models can capture the thermodynamics and kinetics of adsorbed layers for the individual reactants species, such as CO/M(1 0 0) and O/M(1 0 0), as well as the interaction and reaction between different reactant species in mixed adlayers, such as (CO + O)/M(1 0 0). The msLG models allow population of any of hollow, bridge, and top sites. This enables a more flexible and realistic description of adsorption and adlayer ordering, as well as of reaction configurations and configuration-dependent barriers. Adspecies adsorption and interaction energies, as well as barriers for various processes, constitute key model input. The choice of these energies is guided by experimental observations, as well as by extensive Density Functional Theory analysis. Model behavior is assessed via Kinetic Monte Carlo (KMC) simulation. We also address the simulation challenges and theoretical ramifications associated with very rapid diffusion and local equilibration of reactant adspecies such as CO. These msLG models are applied to describe adsorption, ordering, and temperature programmed desorption (TPD) for individual CO/M(1 0 0) and O/M(1 0 0) reactant adlayers. In addition, they are also applied to predict mixed (CO + O)/M(1 0 0) adlayer structure on the nanoscale, the complete bifurcation diagram for reactive steady-states under continuous flow conditions, temperature programmed reaction (TPR) spectra, and titration reactions for the CO-oxidation reaction. Extensive and reasonably successful comparison of model predictions is made with experimental

Teleportations of Mixed States and Multipartite Quantum States

Institute of Scientific and Technical Information of China (English)

YU Chang-Shui; WANG Ya-Hong; SONG He-Shan

2007-01-01

In this paper, we propose a protocol to deterministically teleport an unknown mixed state of qubit by utilizing a maximally bipartite entangled state of qubits as quantum channel. Ifa non-maximally entangled bipartite pure state is employed as quantum channel, the unknown mixed quantum state of qubit can be teleported with 1 - √1 - C2 probability, where C is the concurrence of the quantum channel. The protocol can also be generalized to teleport a mixed state of qudit or a multipartite mixed state. More important purpose is that, on the basis of the protocol, the teleportation of an arbitrary multipartite (pure or mixed) quantum state can be decomposed into the teleportation of each subsystem by employing separate entangled states as quantum channels. In the case of deterministic teleportation,Bob only needs to perform unitary transformations on his single particles in order to recover the initial teleported multipartite quantum state.

Mixed-mode elastic-plastic fracture of 2024-T351 aluminium alloy

International Nuclear Information System (INIS)

Sakata, Masaru; Aoki, Shigeru; Kishimoto, Kikuo; Chikugo, Hiroshi; Takizawa, Masakazu.

1985-01-01

In order to evaluate accurately the strength and structural soundness of the structures made of high toughness materials, it is necessary to clarify the fracture behavior under the loading condition of mixed mode such as oblique cracks as well as the elasto-plastic fracture behavior of the materials in the case of single opening displacement type mode. About the fracture condition in the state of mixed mode, various theories based on the linear fracture mechanics have been proposed. In this study, the elasto-plastic fracture toughness test of mixed mode was carried out by using an aluminum alloy as the subject, and the behavior of dulling and development of cracks was observed with a scanning electron microscope. Moreover, the state of deformation of the test pieces was analyzed by elasto-plastic finite element method, thus the parameters controlling the elasto-plastic fracture of mixed mode were examined. In the range of this study, the limiting stretch zone width in the case of loading of mixed mode was 12 μm similarly to the case of single mode. Also in the case of mixed mode, there was distinct difference between the inclination of a dulling straight line and an R-curve, and the limit value of J intergral was determined by their intersection. (Kako, I.)

Pressure supression pool thermal mixing

International Nuclear Information System (INIS)

Cook, D.H.

1984-10-01

A model is developed and verified to describe the thermal mixing that occurs in the pressure suppression pool (PSP) of a commercial BWR. The model is designed specifically for a Mark-I containment and is intended for use in severe accident sequence analyses. The model developed in this work produces space and time dependent temperature results throughout the PSP and is useful for evaluating the bulk PSP thermal mixing, the condensation effectiveness of the PSP, and the long-term containment integrity. The model is designed to accommodate single or multiple discharging T-quenchers, a PSP circumferential circulation induced by the residual heat removal system discharge, and the thermal stratification of the pool that occurs immediately after the relief valves close. The PSP thermal mixing is verified by comparing the model-predicted temperatures to experimental temperatures that were measured in an operating BWR suppression pool. The model is then used to investigate several PSP thermal mixing problems that include the time to saturate at full relief valve flow, the temperature response to a typical stuck open relief valve scenario, and the effect of operator rotation of the relief valve discharge point

Pressure suppression pool thermal mixing

International Nuclear Information System (INIS)

Cook, D.H.

1984-01-01

A model is developed and verified to describe the thermal mixing that occurs in the pressure suppression pool (PSP) of a commercial BWR. The model is designed specifically for a Mark-I containment and is intended for use in severe accident sequence analyses. The model produces space and time dependent temperature results throughout the PSP and is useful for evaluating the bulk PSP thermal mixing, the condensation effectiveness of the PSP, and the long-term containment integrity. The model is designed to accommodate single or multiple discharging T-quenchers, a PSP circumferential circulation induced by the residual heat removal system discharge, and the thermal stratification of the pool that occurs immediately after the relief valves close. The PSP thermal mixing model is verified by comparing the model predicted temperatures to experimental temperatures that were measured in an operating BWR suppression pool. The model is then used to investigate several PSP thermal mixing problems that include the time to saturate at full relief valve flow, the temperature response to a typical stuck open relief valve scenario, and the effect of operator rotation of the relief valve discharge point

Invisible nursing research: thoughts about mixed methods research and nursing practice.

Science.gov (United States)

Fawcett, Jacqueline

2015-04-01

In this this essay, the author addresses the close connection between mixed methods research and nursing practice. If the assertion that research and practice are parallel processes is accepted, then nursing practice may be considered "invisible mixed methods research," in that almost every encounter between a nurse and a patient involves collection and integration of qualitative (word) and quantitative (number) information that actually is single-case mixed methods research. © The Author(s) 2015.

Assessment of mixed-layer height estimation from single-wavelength ceilometer profiles

Directory of Open Access Journals (Sweden)

T. N. Knepp

2017-10-01

Full Text Available Differing boundary/mixed-layer height measurement methods were assessed in moderately polluted and clean environments, with a focus on the Vaisala CL51 ceilometer. This intercomparison was performed as part of ongoing measurements at the Chemistry And Physics of the Atmospheric Boundary Layer Experiment (CAPABLE site in Hampton, Virginia and during the 2014 Deriving Information on Surface Conditions from Column and Vertically Resolved Observations Relevant to Air Quality (DISCOVER-AQ field campaign that took place in and around Denver, Colorado. We analyzed CL51 data that were collected via two different methods (BLView software, which applied correction factors, and simple terminal emulation logging to determine the impact of data collection methodology. Further, we evaluated the STRucture of the ATmosphere (STRAT algorithm as an open-source alternative to BLView (note that the current work presents an evaluation of the BLView and STRAT algorithms and does not intend to act as a validation of either. Filtering criteria were defined according to the change in mixed-layer height (MLH distributions for each instrument and algorithm and were applied throughout the analysis to remove high-frequency fluctuations from the MLH retrievals. Of primary interest was determining how the different data-collection methodologies and algorithms compare to each other and to radiosonde-derived boundary-layer heights when deployed as part of a larger instrument network. We determined that data-collection methodology is not as important as the processing algorithm and that much of the algorithm differences might be driven by impacts of local meteorology and precipitation events that pose algorithm difficulties. The results of this study show that a common processing algorithm is necessary for light detection and ranging (lidar-based MLH intercomparisons and ceilometer-network operation, and that sonde-derived boundary layer heights are higher (10–15 % at

Mixed-substrate (glycerol tributyrate and fibrin) zymography for simultaneous detection of lipolytic and proteolytic enzymes on a single gel.

Science.gov (United States)

Choi, Nack-Shick; Choi, Jong Hyun; Kim, Bo-Hye; Han, Yun-Jon; Kim, Joong Su; Lee, Seung-Goo; Song, Jae Jun

2009-06-01

A new zymography method for simultaneous detection of two different enzymatic activities (lipolytic and proteolytic) using a single SDS-containing or native-conformation gel and a mixed-substrate (glycerol tributyrate and fibrin) (MS)(1) gel was developed. After routine electrophoresis, SDS in the gel was removed by treatment with Triton X-100. Gel proteins were electrotransferred to the MS gel. To visualize lipolytic activity, the MS gel was incubated at 37 degrees C (for 6 or 24 h) until clear bands against an opaque background were observed. To detect proteolytic activity, the same MS gel was stained with Coomassie brilliant blue. Using this method, we show that six lipolytic enzymes from Staphylococcus pasteuri NJ-1 and four proteolytic enzymes from two Bacillus strains, B. licheniformis DJ-2 and B. licheniformis NJ-5, isolated from soil, can be simultaneously detected.

Mixed Methods in Biomedical and Health Services Research

Science.gov (United States)

Curry, Leslie A.; Krumholz, Harlan M.; O’Cathain, Alicia; Plano Clark, Vicki L.; Cherlin, Emily; Bradley, Elizabeth H.

2013-01-01

Mixed methods studies, in which qualitative and quantitative methods are combined in a single program of inquiry, can be valuable in biomedical and health services research, where the complementary strengths of each approach can yield greater insight into complex phenomena than either approach alone. Although interest in mixed methods is growing among science funders and investigators, written guidance on how to conduct and assess rigorous mixed methods studies is not readily accessible to the general readership of peer-reviewed biomedical and health services journals. Furthermore, existing guidelines for publishing mixed methods studies are not well known or applied by researchers and journal editors. Accordingly, this paper is intended to serve as a concise, practical resource for readers interested in core principles and practices of mixed methods research. We briefly describe mixed methods approaches and present illustrations from published biomedical and health services literature, including in cardiovascular care, summarize standards for the design and reporting of these studies, and highlight four central considerations for investigators interested in using these methods. PMID:23322807

Enhanced solubilization of curcumin in mixed surfactant vesicles.

Science.gov (United States)

Kumar, Arun; Kaur, Gurpreet; Kansal, S K; Chaudhary, Ganga Ram; Mehta, S K

2016-05-15

Self-assemblies of equimolar double and single chain mixed ionic surfactants, with increasing numbers of carbon atoms of double chain surfactant, were analyzed on the basis of fluorescence and conductivity results. Attempts were also made to enhance the solubilization of curcumin in aqueous equimolar mixed surfactant systems. Mixed surfactant assembly was successful in retarding the degradation of curcumin in alkaline media (only 25-28 40% degraded in 10h at pH 13). Fluorescence spectroscopy and fluorescence quenching methods were employed to predict the binding position and mechanism of curcumin with self-assemblies. Results indicate that the interactions take place according to both dynamic and static quenching mechanisms and curcumin was distributed in a palisade layer of mixed aggregates. Antioxidant activity (using DPPH radical) and biocompatibility (using calf-thymus DNA) of curcumin-loaded mixed surfactant formulations were also evaluated. The prepared systems improved the stability, solubility and antioxidant activity of curcumin and additionally are biocompatible. Copyright © 2015 Elsevier Ltd. All rights reserved.

Single-Sex Education in Public School Settings

Science.gov (United States)

Crawford-Ferre, Heather Glynn; Wiest, Lynda R.

2013-01-01

Although researchers have studied the effectiveness of single-sex education (SSE), the findings have been mixed. This exploratory study reports the perceived goals and effectiveness of single-sex education based on interviews with a small group of educators involved with SSE in various ways. Research participants included a school principal and…

Seebeck and Nernst effects in the mixed state of YBa2Cu3Oy single crystals: A probe for the scattering rate of quasiparticles

International Nuclear Information System (INIS)

Sato, Y.; Terasaki, I.; Tajima, S.

1996-01-01

Transport properties under a temperature gradient were investigated in the mixed state of YBa 2 Cu 3 O y single crystals. The ratio of the Seebeck coefficient S xx to the resistivity ρ xx , which is proportional to the thermal current, exhibits a remarkable magnetic field dependence. This implies that the quasiparticles driven by the temperature gradient are scattered by vortices to reduce their lifetime. Quantitative investigation for the H dependence of S xx /ρ xx reveals the lifetime enhancement of the quasiparticle below T c . copyright 1996 The American Physical Society

Basal cell carcinoma of the skin with mixed histomorphology: a comparative study.

Science.gov (United States)

Bartoš, Vladimír; Kullová, Milada

Basal cell carcinoma (BCC) of the skin exhibits a very heterogeneous histomorphology, on the basis of which it is classified into several subtypes and variants. In many cases, however, a definite categorization remains difficult, because BCC may consist of more than one histopathological subtype. There are limited data exploring the characteristics of these mixed BCCs, since they have not been specifically analysed. The aim of this study was to estimate the prevalence of BCCs with mixed histomorphology observed in a set of primary BCCs and to compare their clinicopathological features with a single type BCC subgroup. A total of 911 histologically proven primary BCCs from 697 patients were investigated. Prevalence of single and mixed type BCCs was 64.9 % and 35.1 %, respectively. In mixed type BCC subgroup, a very heterogeneous histomorphology was found comprising a mixture of two to four different subtypes in various proportions. The most frequent combinations included nodular-infiltrative, superficial-nodular, nodular-trichoepithelial and nodular-micronodular subtype. Comparative analysis of the two given subgroups showed that mixed type BCCs were significantly more frequently localized on the extrafacial regions of the head (30.0 % vs. 20.0 %, p = 0.02) and less often on the face (37.2 % vs. 45.2 %, p = 0.03). There were not convincing differences in the occurrence of single vs mixed type BCCs in other parts of the body. Histologically, mixed type BCCs exhibited an aggressive-growth pattern more frequently (64.6 % vs. 13.0 %, p < 0.0001). Positive surgical margins were significantly more common in mixed type BCC subgroup (17.8 % vs. 12.6 %, p = 0.02). Cutaneous BCCs with mixed histomorphology represented about one third of the cases. It is a common finding in routine pathological practice, probably suggestive of evolution and phenotypic transformation of the cancer. Since mixed type BCCs are frequently composed of aggressive histological subtypes, regardless the

Off-diagonal generalization of the mixed-state geometric phase

International Nuclear Information System (INIS)

Filipp, Stefan; Sjoeqvist, Erik

2003-01-01

The concept of off-diagonal geometric phases for mixed quantal states in unitary evolution is developed. We show that these phases arise from three basic ideas: (1) fulfillment of quantum parallel transport of a complete basis, (2) a concept of mixed-state orthogonality adapted to unitary evolution, and (3) a normalization condition. We provide a method for computing the off-diagonal mixed-state phases to any order for unitarities that divide the parallel transported basis of Hilbert space into two parts: one part where each basis vector undergoes cyclic evolution and one part where all basis vectors are permuted among each other. We also demonstrate a purification based experimental procedure for the two lowest-order mixed-state phases and consider a physical scenario for a full characterization of the qubit mixed-state geometric phases in terms of polarization-entangled photon pairs. An alternative second order off-diagonal mixed-state geometric phase, which can be tested in single-particle experiments, is proposed

Does the thermal spike affect low energy ion-induced interfacial mixing?

International Nuclear Information System (INIS)

Suele, P.; Menyhard, M.; Nordlund, K.

2003-01-01

Molecular dynamics simulations have been used to obtain the three-dimensional distribution of interfacial mixing and cascade defects in Ti/Pt multilayer system due to single 1 keV Ar + impact at grazing angle of incidence. The Ti/Pt system was chosen because of its relatively high heat of mixing in the binary alloy and therefore a suitable candidate for testing the effect of heat of mixing on ion-beam mixing. However, the calculated mixing profile is not sensitive to the heat of mixing. Therefore the thermal spike model of mixing is not fully supported under these irradiation conditions. Instead we found that the majority of mixing occurs after the thermal spike during the relaxation process. These conclusions are supported by liquid, vacancy as well as adatom analysis. The interfacial mixing is in various aspects anomalous in this system: the time evolution of mixing is leading to a phase delay for Ti mixing, and Pt exhibits an unexpected double peaked mixing evolution. The reasons to these effects are discussed

Reactivity in inverse micelles

International Nuclear Information System (INIS)

Brochette, Pascal

1987-01-01

This research thesis reports the study of the use of micro-emulsions of water in oil as reaction support. Only the 'inverse micelles' domain of the ternary mixing (water/AOT/isooctane) has been studied. The main addressed issues have been: the micro-emulsion disturbance in presence of reactants, the determination of reactant distribution and the resulting kinetic theory, the effect of the interface on electron transfer reactions, and finally protein solubilization [fr

Improvements in the treatment of zirconium containing ores

International Nuclear Information System (INIS)

Fletcher, G.W.

1975-01-01

A method of conducting an aluminothermic reduction of an oxide of a reactive metal comprising melting in a vessel in an induction furnace a conductive susceptor metal and thereafter adding the required intimately mixed reactants to the molten mass in the container wherein the rate of addition of the reactants and the power input to the induction furnace are controlled to maintain the temperature of the molten mass above a predetermined minimum

LIDAR forest inventory with single-tree, double- and single-phase procedures

Science.gov (United States)

Robert C. Parker; David L. Evans

2009-01-01

Light Detection and Ranging (LIDAR) data at 0.5- to 2-m postings were used with doublesample, stratified inventory procedures involving single-tree attribute relationships in mixed, natural, and planted species stands to yield sampling errors (one-half the confidence interval expressed as a percentage of the mean) ranging from ±2.1 percent to ±11.5...

Mixed finite element simulations in two-dimensional groundwater flow problems

International Nuclear Information System (INIS)

Kimura, Hideo

1989-01-01

A computer code of groundwater flow in two-dimensional porous media based on the mixed finite element method was developed for accurate approximations of Darcy velocities in safety evaluation of radioactive waste disposal. The mixed finite element procedure solves for both the Darcy velocities and pressure heads simultaneously in the Darcy equation and continuity equation. Numerical results of a single well pumping at a constant rate in a uniform flow field showed that the mixed finite element method gives more accurate Darcy velocities nearly 50 % on average error than standard finite element method. (author)

Theoretical studies of potential energy surfaces and computational methods

Energy Technology Data Exchange (ETDEWEB)

Shepard, R. [Argonne National Laboratory, IL (United States)

1993-12-01

This project involves the development, implementation, and application of theoretical methods for the calculation and characterization of potential energy surfaces involving molecular species that occur in hydrocarbon combustion. These potential energy surfaces require an accurate and balanced treatment of reactants, intermediates, and products. This difficult challenge is met with general multiconfiguration self-consistent-field (MCSCF) and multireference single- and double-excitation configuration interaction (MRSDCI) methods. In contrast to the more common single-reference electronic structure methods, this approach is capable of describing accurately molecular systems that are highly distorted away from their equilibrium geometries, including reactant, fragment, and transition-state geometries, and of describing regions of the potential surface that are associated with electronic wave functions of widely varying nature. The MCSCF reference wave functions are designed to be sufficiently flexible to describe qualitatively the changes in the electronic structure over the broad range of geometries of interest. The necessary mixing of ionic, covalent, and Rydberg contributions, along with the appropriate treatment of the different electron-spin components (e.g. closed shell, high-spin open-shell, low-spin open shell, radical, diradical, etc.) of the wave functions, are treated correctly at this level. Further treatment of electron correlation effects is included using large scale multireference CI wave functions, particularly including the single and double excitations relative to the MCSCF reference space. This leads to the most flexible and accurate large-scale MRSDCI wave functions that have been used to date in global PES studies.

The impact of reactants composition and temperature on the flow structure in a wake stabilized laminar lean premixed CH4/H2/air flames; mechanism and scaling

KAUST Repository

Michaels, D.

2016-11-11

In this paper we investigate the role of reactants composition and temperature in defining the steady flow structure in bluff body stabilized premixed flames. The study was motivated by experiments which showed that the flow structure and stability map for different fuels and inlet conditions collapse using the extinction strain rate as the chemical time scale. The investigation is conducted using a laminar lean premixed flame stabilized on a heat conducting bluff-body. Calculations are performed for a wide range of mixtures of CH4/H2/air (0.35 ≤ ϕ ≤ 0.75, 0 ≤ %H2 ≤ 40, 300 ≤ Tin [K] ≤ 500) in order to systematically vary the burning velocity (2.0–35.6 cm/s), dilatation ratio (2.7–6.4), and extinction strain rate (106–2924 1/s). The model is based on a fully resolved unsteady two-dimensional flow with detailed chemistry and species transport, and with no artificial flame anchoring boundary conditions. Calculations reveal that the recirculation zone length correlates with a chemical time scale based on the flame extinction strain rate corresponding to the inlet fuel composition, stoichiometry, pressure and temperature; and are consistent with experimental data in literature. It was found that in the wake region the flame is highly stretched and its location and interaction with the flow is governed by the reactants combustion characteristics under high strain.

Process for producing uranium oxide rich compositions from uranium hexafluoride

International Nuclear Information System (INIS)

DeHollander, W.R.; Fenimore, C.P.

1978-01-01

Conversion of gaseous uranium hexafluoride to a uranium dioxide rich composition in the presence of an active flame in a reactor defining a reaction zone is achieved by separately introducing a first gaseous reactant comprising a mixture of uranium hexafluoride and a reducing carrier gas, and a second gaseous reactant comprising an oxygen-containing gas. The reactants are separated by a shielding gas as they are introduced to the reaction zone. The shielding gas temporarily separates the gaseous reactants and temporarily prevents substantial mixing and reacting of the gaseous reactants. The flame occurring in the reaction zone is maintained away from contact with the inlet introducing the mixture to the reaction zone. After suitable treatment, the uranium dioxide rich composition is capable of being fabricated into bodies of desired configuration for loading into nuclear fuel rods. Alternatively, an oxygen-containing gas as a third gaseous reactant is introduced when the uranium hexafluoride conversion to the uranium dioxide rich composition is substantially complete. This results in oxidizing the uranium dioxide rich composition to a higher oxide of uranium with conversion of any residual reducing gas to its oxidized form

Resolving Mixed Algal Species in Hyperspectral Images

Directory of Open Access Journals (Sweden)

Mehrube Mehrubeoglu

2013-12-01

Full Text Available We investigated a lab-based hyperspectral imaging system’s response from pure (single and mixed (two algal cultures containing known algae types and volumetric combinations to characterize the system’s performance. The spectral response to volumetric changes in single and combinations of algal mixtures with known ratios were tested. Constrained linear spectral unmixing was applied to extract the algal content of the mixtures based on abundances that produced the lowest root mean square error. Percent prediction error was computed as the difference between actual percent volumetric content and abundances at minimum RMS error. Best prediction errors were computed as 0.4%, 0.4% and 6.3% for the mixed spectra from three independent experiments. The worst prediction errors were found as 5.6%, 5.4% and 13.4% for the same order of experiments. Additionally, Beer-Lambert’s law was utilized to relate transmittance to different volumes of pure algal suspensions demonstrating linear logarithmic trends for optical property measurements.

Parents' Views on Mixed and Single-Sex Secondary Schools.

Science.gov (United States)

West, Anne; Hunter, Jay

1993-01-01

Reports on two studies of British parental attitudes toward coeducational and single-sex secondary schools. Finds few differences between the parents of primary school girls and boys who will attend secondary schools in the future. Also finds a large majority of boys' parents believe that social advantages accrue for boys educated with girls. (CFR)

Cord Blood Acute Phase Reactants Predict Early Onset Neonatal Sepsis in Preterm Infants.

Directory of Open Access Journals (Sweden)

Leena B Mithal

Full Text Available Early onset sepsis (EOS is a major cause of morbidity and mortality in preterm infants, yet diagnosis remains inadequate resulting in missed cases or prolonged empiric antibiotics with adverse consequences. Evaluation of acute phase reactant (APR biomarkers in umbilical cord blood at birth may improve EOS detection in preterm infants with intrauterine infection.In this nested case-control study, infants (29.7 weeks gestation, IQR: 27.7-32.2 were identified from a longitudinal cohort with archived cord blood and placental histopathology. Patients were categorized using culture, laboratory, clinical, and antibiotic treatment data into sepsis groups: confirmed sepsis (cEOS, n = 12; presumed sepsis (PS, n = 30; and no sepsis (controls, n = 30. Nine APRs were measured in duplicate from cord blood using commercially available multiplex immunoassays (Bio-Plex Pro™. In addition, placental histopathologic data were linked to biomarker results.cEOS organisms were Escherichia coli, Streptococcus agalactiae, Proteus mirabilis, Haemophilus influenzae and Listeria monocytogenes. C-reactive protein (CRP, serum amyloid A (SAA, haptoglobin (Hp, serum amyloid P and ferritin were significantly elevated in cEOS compared to controls (p<0.01. SAA, CRP, and Hp were elevated in cEOS but not in PS (p<0.01 and had AUCs of 99%, 96%, and 95% respectively in predicting cEOS. Regression analysis revealed robust associations of SAA, CRP, and Hp with EOS after adjustment for covariates. Procalcitonin, fibrinogen, α-2-macroglobulin and tissue plasminogen activator were not significantly different across groups. Placental acute inflammation was associated with APR elevation and was present in all cEOS, 9 PS, and 17 control infants.This study shows that certain APRs are elevated in cord blood of premature infants with EOS of intrauterine origin. SAA, CRP, and Hp at birth have potential diagnostic utility for risk stratification and identification of infants with EOS.

Mixing of ν/sub e/ and ν/sub μ/ in SO(10) models

International Nuclear Information System (INIS)

Milton, K.; Nandi, S.; Tanaka, K.

1982-01-01

We found previously in SO(10) grand unified theories that if the neutrinos have a Dirac mass and a right-handed Majorana mass (approx.10 15 GeV) but no left-handed Majorana mass, there is small ν/sub e/ mixing but ν/sub μ/-ν/sub tau/ mixing can be substantial. We reexamine this problem on the basis of a formalism that assumes that the up, down, lepton, and neutrino mass matrices arise from a single complex 10 and a single 126 Higgs boson. This formalism determines the Majorana mass matrix in terms of quark mass matrices. Adopting three different sets of quark mass matrices that produce acceptable fermion mass ratios and Cabbibo mixing, we obtain results consistent with the above; however, in the optimum case, ν/sub e/-ν/sub μ/ mixing can be of the order of the Cabbibo angle. In an extension of this model wherein the Witten mechanism generates the Majorana mass, we illustrate quantitatively how the parameter characterizing the Majorana sector must be tuned in order to achieve large ν/sub e/-ν/sub μ/ mixing

Mixed Uranium/Refractory Metal Carbide Fuels for High Performance Nuclear Reactors

International Nuclear Information System (INIS)

Knight, Travis; Anghaie, Samim

2002-01-01

Single phase, solid-solution mixed uranium/refractory metal carbides have been proposed as an advanced nuclear fuel for advanced, high-performance reactors. Earlier studies of mixed carbides focused on uranium and either thorium or plutonium as a fuel for fast breeder reactors enabling shorter doubling owing to the greater fissile atom density. However, the mixed uranium/refractory carbides such as (U, Zr, Nb)C have a lower uranium densities but hold significant promise because of their ultra-high melting points (typically greater than 3700 K), improved material compatibility, and high thermal conductivity approaching that of the metal. Various compositions of (U, Zr, Nb)C were processed with 5% and 10% metal mole fraction of uranium. Stoichiometric samples were processed from the constituent carbide powders, while hypo-stoichiometric samples with carbon-to-metal (C/M) ratios of 0.92 were processed from uranium hydride, graphite, and constituent refractory carbide powders. Processing techniques of cold uniaxial pressing, dynamic magnetic compaction, sintering, and hot pressing were investigated to optimize the processing parameters necessary to produce high density (low porosity), single phase, solid-solution mixed carbide nuclear fuels for testing. This investigation was undertaken to evaluate and characterize the performance of these mixed uranium/refractory metal carbides for high performance, ultra-safe nuclear reactor applications. (authors)

Effects of annealing on the properties of atomic layer deposited Ru thin films deposited by NH{sub 3} and H{sub 2} as reactants

Energy Technology Data Exchange (ETDEWEB)

Lee, Seung-Joon; Kim, Soo-Hyun, E-mail: soohyun@ynu.ac.kr

2016-08-01

Atomic layer deposition (ALD) of Ru using a non-oxidizing reactant is indispensable considering its application as a seed layer for Cu electroplating and a bottom electrode for dynamic random access memory capacitors. In this study, ALD-Ru films were deposited using a sequential supply of dicarbonyl-bis(5-methyl-2,4-hexanediketonato) Ru(II) (C{sub 16}H{sub 22}O{sub 6}Ru) and potential non-oxidizing reducing agents, NH{sub 3} or H{sub 2}, as the reactants at a substrate temperature of 250 °C, and the effects of post-annealing in a H{sub 2} ambient on the film properties were investigated. The highly conformal deposition of Ru films was possible using the present reaction scheme but its resistivity was as high as ~ 750 μΩ-cm due to carbon incorporation into the film and the formation of an amorphous structure. Low temperature annealing at 300 °C at H{sub 2} ambient after deposition was found to improve the properties significantly in terms of the resistivity, impurities contents and crystallinity. For example, the film resistivity was decreased drastically to ~ 40 μΩ-cm with both the release of C in the film and crystallization after annealing based on secondary ion mass spectrometry and transmission electron microscopy, whereas perfect step coverage at a very small-sized dual trench (aspect ratio: ~ 3, the top opening size of 45 nm and bottom size of 20 nm) was maintained after annealing. - Highlights: • Ru thin films were deposited by atomic layer deposition (ALD) using NH{sub 3} and H{sub 2} molecules. • Effects of low temperature (300 °C) post-annealing on the film properties were investigated. • Post annealing improved the properties of ALD-Ru films. • Perfect step coverage of ALD-Ru was confirmed at trench structure (top opening width: 45 nm).

Ratiometric, single-dye, pH-sensitive inhibited laser-induced fluorescence for the characterization of mixing and mass transfer

Science.gov (United States)

Lacassagne, Tom; Simoëns, Serge; El Hajem, Mahmoud; Champagne, Jean-Yves

2018-01-01

Inhibited planar laser-induced fluorescence (I-PLIF) techniques are widely used for heat and mass transfer studies in fluid mechanics. They allow the visualization of instantaneous two-dimensional field of a passive or reactive scalar, providing that this scalar acts as an inhibitor to the fluorescence of a specific molecule, and that this molecule is homogeneously mixed in the fluid at a known concentration. Local scalar values are deduced from fluorescence recordings thanks to preliminary calibration procedure. When confronted with non-optically thin systems, however, the knowledge of the excitation intensity distribution in the region of interest is also required, and this information is most of the time hard to obtain. To overcome that problem, two-color ratiometric PLIF techniques ( {I}^ {r}-PLIF) have been developed. In these methods, the ratio of two different fluorescence wavelengths triggered by the same excitation is used as an indicator of the scalar value. Such techniques have been used for temperature measurements in several studies but never, to the author's knowledge, for pH tracking and acid-base mixing, despite the frequent use of the one-color version in mass transfer studies. In the present work, a ratiometric pH-sensitive-inhibited PLIF technique ( {I}_ {pH}^ {r}-PLIF) using fluorescein sodium as a single dye and applicable to complex geometries and flows is developed. Theoretical considerations show that the ratio of the two-color fluorescence intensities should only depend on the dye's spectral quantum yield, itself pH-dependent. A detailed spectrofluorimetric study of fluorescein reveals that this ratio strictly increases with the pH for two well-chosen spectral bands (fluorescence colors). A similar trend is found when using sCmos cameras equipped with optical filters to record fluorescence signals. The method is then experimented on a test flow, a turbulent acidic jet injected in an initially pH-neutral volume of fluid. The results obtained

Laser synthesis of a copper–single-walled carbon nanotube nanocomposite via molecular-level mixing and non-equilibrium solidification

International Nuclear Information System (INIS)

Tu, Jay F; Rajule, Nilesh; Molian, Pal; Liu, Yi

2016-01-01

A copper–single-walled carbon nanotube (Cu–SWCNT) metal nanocomposite could be an ideal material if it can substantially improve the strength of copper while preserving the metal’s excellent thermal and electrical properties. However, synthesis of such a nanocomposite is highly challenging, because copper and SWCNTs do not form intermetallic compounds and are insoluble; as a result, there are serious issues regarding wettability and fine dispersion of SWCNTs within the copper matrix. In this paper we present a novel wet process, called the laser surface implantation process (LSI), to synthesize Cu–SWCNT nanocomposites by mixing SWCNTs into molten copper. The LSI process includes drilling several microholes on a copper substrate, filling the microholes with SWCNTs suspended in solution, and melting the copper substrate to create a micro-well of molten copper. The molten copper advances radially outward to engulf the microholes with pre-deposited SWCNTs to form the Cu–SWCNT implant upon solidification. Rapid and non-equilibrium solidification is achieved due to copper’s excellent heat conductivity, so that SWCNTs are locked in position within the copper matrix without agglomerating into large clusters. This wet process is very different from the typical dry processes used in powder metallurgy. Very high hardness improvement, up to 527% over pure copper, was achieved, confirmed by micro-indentation tests, with only a 0.23% SWCNT volume fraction. The nanostructure of the nanocomposite was characterized by TEM imaging, energy-dispersive x-ray spectroscopy mapping and spectroscopy measurements. The SWCNTs were found to be finely dispersed within the copper matrix with cluster sizes in the range of nanometers, achieving the goal of molecular-level mixing. (paper)

On ternary species mixing and combustion in isotropic turbulence at high pressure

Science.gov (United States)

Lou, Hong; Miller, Richard S.

2004-05-01

Effects of Soret and Dufour cross-diffusion, whereby both concentration and thermal diffusion occur in the presence of mass fraction, temperature, and pressure gradients, are investigated in the context of both binary and ternary species mixing and combustion in isotropic turbulence at large pressure. The compressible flow formulation is based on a cubic real-gas state equation, and includes generalized forms for heat and mass diffusion derived from nonequilibrium thermodynamics and fluctuation theory. A previously derived formulation of the generalized binary species heat and mass fluxes is first extended to the case of ternary species, and appropriate treatment of the thermal and mass diffusion factors is described. Direct numerical simulations (DNS) are then conducted for both binary and ternary species mixing and combustion in stationary isotropic turbulence. Mean flow temperatures and pressures of =700 K and =45 atm are considered to ensure that all species mixtures remain in the supercritical state such that phase changes do not occur. DNS of ternary species systems undergoing both pure mixing and a simple chemical reaction of the form O2+N2→2NO are then conducted. It is shown that stationary scalar states previously observed for binary mixing persist for the ternary species problem as well; however, the production and magnitude of the scalar variance is found to be altered for the intermediate molecular weight species as compared to the binary species case. The intermediate molecular weight species produces a substantially smaller scalar variance than the remaining species for all flows considered. For combustion of nonstoichiometric mixtures, a binary species mixture, characterized by stationary scalar states, results at long times after the lean reactant is depleted. The form of this final scalar distribution is observed to be similar to that found in the binary flow situation. A series of lower resolution simulations for a variety of species is then

Mixed chemical-induced oxidative stress in occupational exposure ...

African Journals Online (AJOL)

Mixed chemical-induced oxidative stress in occupational exposure in Nigerians. JI Anetor, SA Yaqub, GO Anetor, AC Nsonwu, FAA Adeniyi, S Fukushima. Abstract. Exposure to single chemicals and associated disorders in occupational environments has received significant attention. Understanding these events holds ...

Mixed-methods approaches in health research in Nepal

OpenAIRE

Simkhada, Padam; Van Teijlingen, Edwin; Wasti, Sharada Prasad; Sathian, B.

2014-01-01

Combining and integrating a mixture of qualitative and quantitative methods in one single study is widely used in health and social care research in high-income countries. This editorial adds a few words of advice to the novice mixed-methods researcher in Nepal.

Entropy and chemical change. 1: Characterization of product (and reactant) energy distributions in reactive molecular collisions: Information and enthropy deficiency

Science.gov (United States)

Bernstein, R. B.; Levine, R. D.

1972-01-01

Optimal means of characterizing the distribution of product energy states resulting from reactive collisions of molecules with restricted distributions of initial states are considered, along with those for characterizing the particular reactant state distribution which yields a given set of product states at a specified total energy. It is suggested to represent the energy-dependence of global-type results in the form of square-faced bar plots, and of data for specific-type experiments as triangular-faced prismatic plots. The essential parameters defining the internal state distribution are isolated, and the information content of such a distribution is put on a quantitative basis. The relationship between the information content, the surprisal, and the entropy of the continuous distribution is established. The concept of an entropy deficiency, which characterizes the specificity of product state formation, is suggested as a useful measure of the deviance from statistical behavior. The degradation of information by experimental averaging is considered, leading to bounds on the entropy deficiency.

Defect-induced mix experiment for NIF

Directory of Open Access Journals (Sweden)

Schmitt M.J.

2013-11-01

Full Text Available The Defect Induced Mix Experiment (DIME-II will measure the implosion and mix characteristics of CH capsules filled with 5 atmospheres of DT by incorporating mid-Z dopant layers of Ge and Ga. This polar direct drive (PDD experiment also will demonstrate the filling of a CH capsule at target chamber center using a fill tube. Diagnostics for these experiments include areal x-ray backlighting to obtain early time images of the implosion trajectory and a multiple-monochromatic imager (MMI to collect spectrally-resolved images of the capsule dopant line emission near bangtime. The inclusion of two (or more thin dopant layers at separate depths within the capsule shell facilitates spatial correlation of mix between the layers and the hot gas core on a single shot. The dopant layers are typically 2 μm thick and contain dopant concentrations of 1.5%. Three dimensional Hydra simulations have been performed to assess the effects of PDD asymmetry on capsule performance.

Performance simulation of planar SOFC using mixed hydrogen and carbon monoxide gases as fuel

Energy Technology Data Exchange (ETDEWEB)

Inui, Y. [Department of Electrical and Electronic Engineering, Toyohashi University of Technology, Tempaku-cho, Toyohashi 441-8580 (Japan)]. E-mail: inui@eee.tut.ac.jp; Urata, A. [Department of Electrical and Electronic Engineering, Toyohashi University of Technology, Tempaku-cho, Toyohashi 441-8580 (Japan); Ito, N. [Department of Electrical and Electronic Engineering, Toyohashi University of Technology, Tempaku-cho, Toyohashi 441-8580 (Japan); Nakajima, T. [Department of Electrical and Electronic Engineering, Toyohashi University of Technology, Tempaku-cho, Toyohashi 441-8580 (Japan); Tanaka, T. [Department of Electrical and Electronic Engineering, Toyohashi University of Technology, Tempaku-cho, Toyohashi 441-8580 (Japan)

2006-08-15

The authors investigate in detail the influence of the mixing ratio of hydrogen and carbon monoxide in the fuel on the cell performance of the SOFC through numerical simulations for a single cell plate of the co-flow type planar cell. It is made clear that the cell performance is almost the same and excellent, independent of the mixing ratio of hydrogen and carbon monoxide under the nominal operating condition. The electromotive force of the hydrogen rich fuel gas is a little higher than that of the carbon monoxide rich fuel gas. The internal voltage drop in the cell decreases as the fraction of carbon monoxide becomes high. Since the value of the single cell voltage is determined by the balance of these two phenomena, the lowering of the electromotive force is dominant and the single cell voltage of the hydrogen rich fuel gas is higher when the inlet gas temperature is high, whereas the voltage drop reduction is dominant and the single cell voltage of the carbon monoxide rich fuel gas is higher when the temperature is low. The effect of the additional gases of water vapor and carbon dioxide is restricted to the single cell voltage shift, and the qualitative dependence of the single cell voltage on the inlet gas temperature is determined by the mixing ratio of hydrogen and carbon monoxide.

Performance simulation of planar SOFC using mixed hydrogen and carbon monoxide gases as fuel

International Nuclear Information System (INIS)

Inui, Y.; Urata, A.; Ito, N.; Nakajima, T.; Tanaka, T.

2006-01-01

The authors investigate in detail the influence of the mixing ratio of hydrogen and carbon monoxide in the fuel on the cell performance of the SOFC through numerical simulations for a single cell plate of the co-flow type planar cell. It is made clear that the cell performance is almost the same and excellent, independent of the mixing ratio of hydrogen and carbon monoxide under the nominal operating condition. The electromotive force of the hydrogen rich fuel gas is a little higher than that of the carbon monoxide rich fuel gas. The internal voltage drop in the cell decreases as the fraction of carbon monoxide becomes high. Since the value of the single cell voltage is determined by the balance of these two phenomena, the lowering of the electromotive force is dominant and the single cell voltage of the hydrogen rich fuel gas is higher when the inlet gas temperature is high, whereas the voltage drop reduction is dominant and the single cell voltage of the carbon monoxide rich fuel gas is higher when the temperature is low. The effect of the additional gases of water vapor and carbon dioxide is restricted to the single cell voltage shift, and the qualitative dependence of the single cell voltage on the inlet gas temperature is determined by the mixing ratio of hydrogen and carbon monoxide

Mean-Field Studies of a Mixed Spin-3/2 and Spin-2 and a Mixed Spin-3/2 and Spin-5/2 Ising System with Different Anisotropies

International Nuclear Information System (INIS)

Wei Guozhu; Miao Hailing

2009-01-01

The magnetic properties of a mixed spin-3/2 and spin-2 and a mixed spin-3/2 and spin-5/2 Ising ferromagnetic system with different anisotropies are studied by means of mean-field theory (MFT). The dependence of the phase diagram on single-ion anisotropy strengths is studied too. In the mixed spin-3/2 and spin-2 Ising model, besides the second-order phase transition, the first order-disorder phase transition and the tricritical line are found. In the mixed spin-3/2 and spin-5/2 Ising model, there is no first-order transition and tricritical line. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

Integrated aeroelastic vibrator for fluid mixing in open microwells

Science.gov (United States)

Xia, H. M.; Jin, X.; Zhang, Y. Y.; Wu, J. W.; Zhang, J.; Wang, Z. P.

2018-01-01

Fluid mixing in micro-wells/chambers is required in a variety of biological and biochemical processes. However, mixing fluids of small volumes is usually difficult due to increased viscous effects. In this study, we propose a new method for mixing enhancement in microliter-scale open wells. A thin elastic diaphragm is used to seal the bottom of the mixing microwell, underneath which an air chamber connects an aeroelastic vibrator. Driven by an air flow, the vibrator produces self-excited vibrations and causes pressure oscillations in the air chamber. Then the elastic diaphragm is actuated to mix the fluids in the microwell. Two designs that respectively have one single well and 2  ×  2 wells were prototyped. Testing results show that for liquids with a volume ranging from 10-60 µl and viscosity ranging from 1-5 cP, complete mixing can be obtained within 5-20 s. Furthermore, the device is operable with an air micropump, and hence facilitating the miniaturization and integration of lab-on-a-chip and microbioreactor systems.

Morphology development during single droplet drying of mixed component formulations and milk

NARCIS (Netherlands)

Both, E.M.; Nuzzo, N.; Millqvist-Fureby, A.; Boom, R.M.; Schutyser, M.A.I.

2018-01-01

We report on the influence of selected components and their mixtures on the development of the morphology during drying of single droplets and extend the results to the morphology of whole milk powder particles. Sessile single droplet drying and acoustic levitation methods were employed to study

QCD sum-rules analysis of vector (1-) heavy quarkonium meson-hybrid mixing

Science.gov (United States)

Palameta, A.; Ho, J.; Harnett, D.; Steele, T. G.

2018-02-01

We use QCD Laplace sum rules to study meson-hybrid mixing in vector (1-) heavy quarkonium. We compute the QCD cross-correlator between a heavy meson current and a heavy hybrid current within the operator product expansion. In addition to leading-order perturbation theory, we include four- and six-dimensional gluon condensate contributions as well as a six-dimensional quark condensate contribution. We construct several single and multiresonance models that take known hadron masses as inputs. We investigate which resonances couple to both currents and so exhibit meson-hybrid mixing. Compared to single resonance models that include only the ground state, we find that models that also include excited states lead to significantly improved agreement between QCD and experiment. In the charmonium sector, we find that meson-hybrid mixing is consistent with a two-resonance model consisting of the J /ψ and a 4.3 GeV resonance. In the bottomonium sector, we find evidence for meson-hybrid mixing in the ϒ (1 S ) , ϒ (2 S ), ϒ (3 S ), and ϒ (4 S ).

Structural Complexity and Ecosystem Functions in a Natural Mixed Forest under a Single-Tree Selection Silviculture

Directory of Open Access Journals (Sweden)

Toshiya Yoshida

2017-11-01

Full Text Available The objective of forest management has become broader, and it is essential to harmonize timber production with conservation of the forest ecosystem. Selection cutting is recognized as a major alternative of clear-cutting, because it can maintain the complexity and heterogeneity of a natural forest; however, its long-term evaluations are limited. This study compared various attributes of stand structures, which are indicators of biodiversity and ecosystem carbon stock between managed and unmanaged blocks (12.6 ha area in total in a natural mixed forest in Hokkaido, the northernmost island of Japan. We found that 30 years’ implementation of single-tree selection did not affect the volume, size structure, species diversity nor spatial distribution of overstory trees in the managed stands. Also, the total carbon stock in the managed stands was almost equal to that of the unmanaged stands. In contrast, several structural attributes and indicator elements that are significant for biodiversity (such as large-diameter live trees, dead trees, cavities, epiphytic bryophytes, and some avian guilds showed marked decrease in the managed stands. We conclude that it is required to leave these structures and elements to some extent for deriving the merit of the management as an alternative silvicultural regime in the region.

A mixed-methods approach to systematic reviews.

Science.gov (United States)

Pearson, Alan; White, Heath; Bath-Hextall, Fiona; Salmond, Susan; Apostolo, Joao; Kirkpatrick, Pamela

2015-09-01

There are an increasing number of published single-method systematic reviews that focus on different types of evidence related to a particular topic. As policy makers and practitioners seek clear directions for decision-making from systematic reviews, it is likely that it will be increasingly difficult for them to identify 'what to do' if they are required to find and understand a plethora of syntheses related to a particular topic.Mixed-methods systematic reviews are designed to address this issue and have the potential to produce systematic reviews of direct relevance to policy makers and practitioners.On the basis of the recommendations of the Joanna Briggs Institute International Mixed Methods Reviews Methodology Group in 2012, the Institute adopted a segregated approach to mixed-methods synthesis as described by Sandelowski et al., which consists of separate syntheses of each component method of the review. Joanna Briggs Institute's mixed-methods synthesis of the findings of the separate syntheses uses a Bayesian approach to translate the findings of the initial quantitative synthesis into qualitative themes and pooling these with the findings of the initial qualitative synthesis.

Perturbation treatment of mixing in Josephson junctions

International Nuclear Information System (INIS)

Levinsen, M.T.; Ulrich, B.T.

1975-01-01

A current biased, resistively shunted Josephson Junction irradiated at two frequencies is considered. The perturbation technique introduced by Aslamasov and Larkin is used in the calculations, and both signals are treated as perturbations. The second order calculation yields the size of the mixing steps at V/sub +-/ = h(ω 1 +- ω 2 )/2e. As in the case of a single frequency, subharmonic mixing steps are absent. The amplitude of the voltage oscillation at the difference and sum frequencies is shown to be non-zero at all voltages. The microwave resistance is calculated for one frequency ω 2 to third order in the perturbation. There are negative resistance regions near V/sub +-/ (as well as near V 2 = hω 2 /2e). Near V/sub -/, the negative resistance region appears for bias voltage V just above V/sub -/, while near V the region appears for V just below V/sub +/. This means that when an incident frequency mixes with a cavity mode, the mixing step at V/sub -/ will be inverted compared to the cavity step itself

Flow structure of steam-water mixed spray

International Nuclear Information System (INIS)

Sanada, Toshiyuki; Mitsuhashi, Yuki; Mizutani, Hiroya; Saito, Takayuki

2010-01-01

In this study, the flow structure of a steam-water mixed spray is studied both numerically and experimentally. The velocity and pressure profiles of single-phase flow are calculated using numerical methods. On the basis of the calculated flow fields, the droplet behavior is predicted by a one-way interaction model. This numerical analysis reveals that the droplets are accelerated even after they are sprayed from the nozzle. Experimentally, the mixed spray is observed using an ultra-high-speed video camera, and the velocity field is measured by using the oarticle image velocimetry (PIV) technique. Along with this PIV velocity field measurement, the velocities and diameters of droplets are measured by phase Doppler anemometry. Furthermore, the mixing process of steam and water and the atomization process of a liquid film are observed using a transparent nozzle. High-speed photography observations reveal that the flow inside the nozzle is annular flow and that most of the liquid film is atomized at the nozzle throat and nozzle outlet. Finally, the optimum mixing method for steam and water is determined.

Flow structure of steam-water mixed spray

Energy Technology Data Exchange (ETDEWEB)

Sanada, Toshiyuki, E-mail: ttsanad@ipc.shizuoka.ac.j [Department of Mechanical Engineering, Shizuoka University, 3-5-1 Johoku, Naka-ku, Hamamatsu 432-8561, Shizuoka (Japan); Mitsuhashi, Yuki; Mizutani, Hiroya; Saito, Takayuki [Department of Mechanical Engineering, Shizuoka University, 3-5-1 Johoku, Naka-ku, Hamamatsu 432-8561, Shizuoka (Japan)

2010-12-15

In this study, the flow structure of a steam-water mixed spray is studied both numerically and experimentally. The velocity and pressure profiles of single-phase flow are calculated using numerical methods. On the basis of the calculated flow fields, the droplet behavior is predicted by a one-way interaction model. This numerical analysis reveals that the droplets are accelerated even after they are sprayed from the nozzle. Experimentally, the mixed spray is observed using an ultra-high-speed video camera, and the velocity field is measured by using the oarticle image velocimetry (PIV) technique. Along with this PIV velocity field measurement, the velocities and diameters of droplets are measured by phase Doppler anemometry. Furthermore, the mixing process of steam and water and the atomization process of a liquid film are observed using a transparent nozzle. High-speed photography observations reveal that the flow inside the nozzle is annular flow and that most of the liquid film is atomized at the nozzle throat and nozzle outlet. Finally, the optimum mixing method for steam and water is determined.

Synthesis, spectral and single crystal X-ray structural studies on bis(2,2’-bipyridinesulphidoM(II (M = Cu or Zn and diaqua 2,2’-bipyridine zinc(IIsulphate dihydrate

Directory of Open Access Journals (Sweden)

ARUMUGAM MANOHAR

2010-08-01

Full Text Available Reaction of bis(diethanoldithiocarbamatocopper(II, [Cu(deadtc2] and bis(di-n-propyldithiocarbamatozinc(II, [Zn(dnpdtc2] complexes with 2,2’-bipyridine (2,2’-bipy (1:1 ratio in ethanol was investigated. Simple mixing of the reactants in 1:1 ratio resulted in five-coordinated [Cu(2,2’--bipy2S]•CH3CH2OSO3H (1 and [Zn(2,2’-bipy2S]•CH3CH2OSO3H·2H2O (2. Refluxing the reactants and cooling the contents result in the formation of [Zn(2,2’-bipy(H2O2]SO4 (3 and [Cu(2,2’-bipy(H2O2]SO4 (4. Complexes 1 and 2 are monomeric with trigonal bipyramidal geometry. A distorted octahedral environment was observed in complexes 3 and 4. The crystal structure of 4 has already been reported in the literature. Crystal structures of 1, 2 and 3 are reported in this paper. The M–S distances in 1 and 2 are 2.318(1 Å and 2.323 Å, respectively. The N–M–S angles are larger than the N–M–N angles due to the steric requirements.

Independent Orbiter Assessment (IOA): Assessment of the electrical power generation/power reactant storage and distribution subsystem FMEA/CIL

Science.gov (United States)

Ames, B. E.

1988-01-01

The results of the Independent Orbiter Assessment (IOA) of the Failure Modes and Effects Analysis (FMEA) and Critical Items List (CIL) is presented. The IOA effort first completed an analysis of the Electrical Power Generation/Power Reactant Storage and Distribution (EPG/PRSD) subsystem hardware, generating draft failure modes and potential critical items. To preserve independence, this analysis was accomplished without reliance upon the results contained within the NASA FMEA/CIL documentation. The IOA results were then compared to the NASA FMEA/CIL baselines with proposed Post 51-L updates included. A resolution of each discrepancy from the comparison is provided through additional analysis as required. The results of that comparison are documented for the Orbiter EPG/PRSD hardware. The comparison produced agreement on all but 27 FMEAs and 9 CIL items. The discrepancy between the number of IOA findings and NASA FMEAs can be partially explained by the different approaches used by IOA and NASA to group failure modes together to form one FMEA. Also, several IOA items represented inner tank components and ground operations failure modes which were not in the NASA baseline.

Characterization of Cr-rich Cr-Sb multilayer films: Syntheses of a new metastable phase using modulated elemental reactants

International Nuclear Information System (INIS)

Regus, Matthias; Mankovsky, Sergiy; Polesya, Svitlana; Kuhn, Gerhard; Ditto, Jeffrey; Schürmann, Ulrich; Jacquot, Alexandre; Bartholomé, Kilian; Näther, Christian; Winkler, Markus; König, Jan D.; Böttner, Harald; Kienle, Lorenz; Johnson, David C.; Ebert, Hubert; Bensch, Wolfgang

2015-01-01

The new metastable compound Cr 1+x Sb with x up to 0.6 has been prepared via a thin film approach using modulated elemental reactants and investigated by in-situ X-ray reflectivity, X-ray diffraction, differential scanning calorimetry, energy dispersive X-ray analysis as well as transmission electron microscopy and atomic force microscopy. The new Cr-rich antimonide crystallizes in a structure related to the Ni 2 In-type structure, where the crystallographic position (1/3, 2/3, 3/4) is partially occupied by excess Cr. The elemental layers of the pristine material interdiffused significantly before Cr 1+x Sb crystallized. A change in the activation energy was observed for the diffusion process when crystal growth starts. First-principles electronic structure calculations provide insight into the structural stability, magnetic properties and resistivity of Cr 1+x Sb. - Graphical abstract: 1 amorphous multilayered film 2 interdiffused amorphous film 3 metastable crystalline phase 4 thermodynamic stable phase (and by-product). - Highlights: • Interdiffusion of amorphous Cr and Sb occurs before crystallization. • Crystallization of a new metastable phase Cr 1.6 Sb in Ni 2 In-type structure. • The new Cr-rich phase shows half-metallic behavior

Effects of Single-Gender Middle School Classes on Science Achievement and Attitude

Science.gov (United States)

Brooks, Tanisha

Many girls continue to achieve below their male counterparts and portray negative attitudes towards science classes. Some school districts are using single-gender education as a way to shrink the gender gap in school achievement and science related attitude. The purpose of this study was to compare achievement and science-related attitudes of 7th grade girls in single-gender education to 7th grade girls in mixed-gender education. The theoretical base for this study included knowledge from brain-based learning and assimilation, accommodation and age factors of Piaget's theory of cognitive development. The 12-week study included 48 7th grade girls, 21 in the single-gender classroom and 14 in each mixed-gender classroom. This quantitative randomized posttest only control group design utilized the TerraNova Science Assessment and the Test of Science Related Attitudes. Analysis of Variance (ANOVA) was used to determine if significant differences existed in the achievement and attitudes of girls in single and mixed-gender science classes. ANOVA analyses revealed that the girls in the single-gender classroom showed a significantly higher achievement level when compared to girls in the mixed-gender classrooms. Results showed no significant difference in attitude between the two groups. The results of this study contribute to social change by raising awareness about gender issues in science achievement and attitude, addressing a deficiency in the single-gender science education literature, and assisting educational systems in decision making to address achievement gaps while moving toward adequate yearly progress and meeting the requirements of the No Child Left Behind Act of 2001.

Effects of sludge recirculation rate and mixing time on performance of a prototype single-stage anaerobic digester for conversion of food wastes to biogas and energy recovery.

Science.gov (United States)

Ratanatamskul, Chavalit; Saleart, Tawinan

2016-04-01

Food wastes have been recognized as the largest waste stream and accounts for 39.25 % of total municipal solid waste in Thailand. Chulalongkorn University has participated in the program of in situ energy recovery from food wastes under the Ministry of Energy (MOE), Thailand. This research aims to develop a prototype single-stage anaerobic digestion system for biogas production and energy recovery from food wastes inside Chulalongkorn University. Here, the effects of sludge recirculation rate and mixing time were investigated as the main key parameters for the system design and operation. From the results obtained in this study, it was found that the sludge recirculation rate of 100 % and the mixing time of 60 min per day were the most suitable design parameters to achieve high efficiencies in terms of chemical oxygen demand (COD), total solids (TS), and total volatile solid (TVS) removal and also biogas production by this prototype anaerobic digester. The obtained biogas production was found to be 0.71 m(3)/kg COD and the composition of methane was 61.6 %. Moreover, the efficiencies of COD removal were as high as 82.9 % and TVS removal could reach 83.9 % at the optimal condition. Therefore, the developed prototype single-stage anaerobic digester can be highly promising for university canteen application to recover energy from food wastes via biogas production.

The physical and chemical properties of nanostructured mixed-metal catalysts

Energy Technology Data Exchange (ETDEWEB)

Liu, Li [Texas A & M Univ., College Station, TX (United States); Goodman, David Wayne [Texas A & M Univ., College Station, TX (United States)

2016-04-21

The main targets of this study has been to synthesize well-defined nanoclusters of Ni, Co, Pt, Rh and Pd as well as mixed-metal nanoclusters on ultrathin oxide surfaces and to characterize their detailed morphology using scanning probe techniques. The focus of the research is an understanding of the effects of metal-substrate interactions and overall composition on the structure/stability of single metal and mixed-metal nanoclusters and their catalytic activity.

Mixed waste treatment using the ChemChar thermolytic detoxification technique

Energy Technology Data Exchange (ETDEWEB)

Kuchynka, D. [Mirage Systems, Sunnyvale, CA (United States)

1995-10-01

The diversity of mixed waste matrices contained at Department of Energy sites that require treatment preclude a single, universal treatment technology capable of handling sludges, solids, heterogeneous debris, aqueous and organic liquids and soils. This report describes the ChemChar thermolytic detoxification process. The process is a thermal, chemically reductive technology that converts the organic portion of mixed wastes to a synthesis gas, while simultaneously absorbing volatile inorganics on a carbon-based char.

Using mixed methods research in medical education: basic guidelines for researchers.

Science.gov (United States)

Schifferdecker, Karen E; Reed, Virginia A

2009-07-01

Mixed methods research involves the collection, analysis and integration of both qualitative and quantitative data in a single study. The benefits of a mixed methods approach are particularly evident when studying new questions or complex initiatives and interactions, which is often the case in medical education research. Basic guidelines for when to use mixed methods research and how to design a mixed methods study in medical education research are not readily available. The purpose of this paper is to remedy that situation by providing an overview of mixed methods research, research design models relevant for medical education research, examples of each research design model in medical education research, and basic guidelines for medical education researchers interested in mixed methods research. Mixed methods may prove superior in increasing the integrity and applicability of findings when studying new or complex initiatives and interactions in medical education research. They deserve an increased presence and recognition in medical education research.

Design optimization of single mixed refrigerant natural gas liquefaction process using the particle swarm paradigm with nonlinear constraints

International Nuclear Information System (INIS)

Khan, Mohd Shariq; Lee, Moonyong

2013-01-01

The particle swarm paradigm is employed to optimize single mixed refrigerant natural gas liquefaction process. Liquefaction design involves multivariable problem solving and non-optimal execution of these variables can waste energy and contribute to process irreversibilities. Design optimization requires these variables to be optimized simultaneously; minimizing the compression energy requirement is selected as the optimization objective. Liquefaction is modeled using Honeywell UniSim Design ™ and the resulting rigorous model is connected with the particle swarm paradigm coded in MATLAB. Design constraints are folded into the objective function using the penalty function method. Optimization successfully improved efficiency by reducing the compression energy requirement by ca. 10% compared with the base case. -- Highlights: ► The particle swarm paradigm (PSP) is employed for design optimization of SMR NG liquefaction process. ► Rigorous SMR process model based on UniSim is connected with PSP coded in MATLAB. ► Stochastic features of PSP give more confidence in the optimality of complex nonlinear problems. ► Optimization with PSP notably improves energy efficiency of the SMR process.

Pore-Scale Study of Transverse Mixing Induced CaCO ₃ Precipitation and Permeability Reduction in a Model Subsurface Sedimentary System

Energy Technology Data Exchange (ETDEWEB)

Zhang, Changyong; Dehoff, Karl; Hess, Nancy; Oostrom, Mart; Wietsma, Thomas W.; Valocchi, Albert J.; Fouke, Bruce W.; Werth, Charles J.

2010-10-15

A microfluidic pore structure etched into a silicon wafer was used as a two-dimensional model subsurface sedimentary system (i.e., a micromodel) to study mineral precipitation and permeability reduction relevant to groundwater remediation and geological carbon sequestration. Solutions containing CaCl₂ and Na₂CO₃ at four different saturation states (Ω = [Ca²⁺] [CO^32-] / KspCaCO₃) were introduced through two separate inlets and they mixed by diffusion transverse to the main flow direction along the center of the micromodel resulting in CaCO₃ precipitation. Precipitation rates increased and the total amount of precipitates decreased with increasing saturation state, and only vaterite and calcite crystals were formed (no aragonite). The relative amount of vaterite increased from 80% at the lowest saturation (Ω_v = 2.8 for vaterite) state to 95% at the highest saturation state (Ω_v = 4.5). Fluorescent tracer tests conducted before and after CaCO₃ precipitation indicate that pore spaces were completely occluded by CaCO₃ precipitates along the transverse mixing zone, thus significantly reducing porosity and permeability, and potentially limiting transformation from vaterite to the more stable calcite. The results suggest that mineral precipitation along plume margins can decrease both reactant mixing during groundwater remediation, and injection and storage efficiency during CO₂ sequestration.

Mixed methods research - the best of both worlds?

Science.gov (United States)

van Griensven, Hubert; Moore, Ann P; Hall, Valerie

2014-10-01

There has been a bias towards quantitative research approaches within manual therapy, which may have resulted in a narrow understanding of manual therapy practice. The aim of this Masterclass is to make a contribution to the expansion of methodologies used in manual therapy enquiry by discussing mixed methods research (MMR), a methodology which utilises both qualitative and quantitative methods within a single study in order to provide more comprehensive insights. To review rationales for MMR, as well as some of the common design options and potential difficulties. The paper also discusses theoretical frameworks that have been used to underpin qualitative and quantitative research, and ongoing debates about the possibility of combining them. Complexities associated with health and manual therapy cannot always be investigated satisfactorily by using a single research method. Some issues require a more comprehensive understanding, which may be provided by combining the strengths of quantitative and qualitative methods in a mixed methods study. Copyright © 2014 Elsevier Ltd. All rights reserved.

Mixing in Circular and Non-circular Jets in Crossflow

DEFF Research Database (Denmark)

Salewski, Mirko; Stankovic, D.; Fuchs, L.

2008-01-01

orthogonal decomposition of the transverse velocity indicates that coherent structures may be responsible for this phenomenon. Nozzles which have a single-peaked distribution have stronger modes in transverse direction. The global mixing performance is superior for these nozzle types. This is the case......Coherent structures and mixing in the flow field of a jet in crossflow have been studied using computational (large eddy simulation) and experimental (particle image velocimetry and laser-induced fluorescence) techniques. The mean scalar fields and turbulence statistics as determined by both...

[Effects of long-term mixed application of organic and inorganic fertilizers on canopy apparent photosynthesis and yield of winter wheat].

Science.gov (United States)

Zhao, Jun; Dong, Shu-ting; Liu, Peng; Zhang, Ji-wang; Zhao, Bin

2015-08-01

A field experiment was conducted using the winter wheat (Triticum aestivum) variety Shimai 15. The source of organic nitrogen was cow manure, and four fertilization treatments were included, i.e., no N fertilizer application, single application of urea, single application of cow manure, and mixed application of urea and cow manure. The effects of different applications of inorganic and organic nitrogen on canopy apparent photosynthesis (CAP), photosynthetic rate of flag leaves (Pn), leaf area index (LAI), florescence parameters and grain yield of winter wheat were determined. The results showed that urea had the largest effect on the early growth period, as at this stage the CAP, Pn and LAI of the single application of urea were the highest, which was followed by the mixed application and the single application of cow manure. However, 10 days after anthesis, the single application of cow manure and the mixed application delayed the leaf senescence process when compared with the single application of urea. This could be due to the two treatments having higher anti-oxidant enzyme activity and promoting a longer green leaf duration, which could maintain a higher photosynthetic capability. What' s more, the mixed application had a better performance and got the highest grain yield. Consequently, the mixed application of organic and inorganic fertilizers could delay leaf senescence and maintain a better canopy structure and higher photosynthesis capability at the late grain filling stage, which resulted in a higher grain yield.

Analysis of the Δ(X) - L intervalley mixing in group-IV heterostructures

Science.gov (United States)

Kiselev, A. A.; Kim, K. W.; Yablonovitch, E.

2005-06-01

We provide a treatment of the problem of Δ(X) - L intervalley mixing in differently oriented SiGe heterostructures in the transparent effective mass method. Mixing potentials can be calculated, considering changes in the constituent Concentrations of individual heterolayers from some "virtual crystal level" as a bunch of microscopic single-ion perturbations. Strong mixing between lowest localized Δ and L states can be achieved in (113) structures, making them favorable for the electrically controlled gigantic intervalley g factor modulation. We provide estimates for the mixing potential and further consider limitations related to the strength of the in-plane localization and quality of the interface.

Jet mixing long horizontal storage tanks

International Nuclear Information System (INIS)

Perona, J.J.; Hylton, T.D.; Youngblood, E.L.; Cummins, R.L.

1994-12-01

Large storage tanks may require mixing to achieve homogeneity of contents for several reasons: prior to sampling for mass balance purposes, for blending in reagents, for suspending settled solids for removal, or for use as a feed tank to a process. At ORNL, mixed waste evaporator concentrates are stored in 50,000-gal tanks, about 12 ft in diameter and 60 ft long. This tank configuration has the advantage of permitting transport by truck and therefore fabrication in the shop rather than in the field. Jet mixing experiments were carried out on two model tanks: a 230-gal (1/6-linear-scale) Plexiglas tank and a 25,000-gal tank (about 2/3 linear scale). Mixing times were measured using sodium chloride tracer and several conductivity probes distributed through the tanks. Several jet sizes and configurations were tested. One-directional and two-directional jets were tested in both tanks. Mixing times for each tank were correlated with the jet Reynolds number. Mixing times were correlated for the two tank sizes using the recirculation time for the developed jet. When the recirculation times were calculated using the distance from the nozzle to the end of the tank as the length of the developed jet, the correlation was only marginally successful. Data for the two tank sizes were correlated empirically using a modified effective jet length expressed as a function of the Reynolds number raised to the 1/3 power. Mixing experiments were simulated using the TEMTEST computer program. The simulations predicted trends correctly and were within the scatter of the experimental data with the lower jet Reynolds numbers. Agreement was not as good at high Reynolds numbers except for single nozzles in the 25,000-gal tank, where agreement was excellent over the entire range

Mixing with applications to inertial-confinement-fusion implosions

Science.gov (United States)

Rana, V.; Lim, H.; Melvin, J.; Glimm, J.; Cheng, B.; Sharp, D. H.

2017-01-01

Approximate one-dimensional (1D) as well as 2D and 3D simulations are playing an important supporting role in the design and analysis of future experiments at National Ignition Facility. This paper is mainly concerned with 1D simulations, used extensively in design and optimization. We couple a 1D buoyancy-drag mix model for the mixing zone edges with a 1D inertial confinement fusion simulation code. This analysis predicts that National Ignition Campaign (NIC) designs are located close to a performance cliff, so modeling errors, design features (fill tube and tent) and additional, unmodeled instabilities could lead to significant levels of mix. The performance cliff we identify is associated with multimode plastic ablator (CH) mix into the hot-spot deuterium and tritium (DT). The buoyancy-drag mix model is mode number independent and selects implicitly a range of maximum growth modes. Our main conclusion is that single effect instabilities are predicted not to lead to hot-spot mix, while combined mode mixing effects are predicted to affect hot-spot thermodynamics and possibly hot-spot mix. Combined with the stagnation Rayleigh-Taylor instability, we find the potential for mix effects in combination with the ice-to-gas DT boundary, numerical effects of Eulerian species CH concentration diffusion, and ablation-driven instabilities. With the help of a convenient package of plasma transport parameters developed here, we give an approximate determination of these quantities in the regime relevant to the NIC experiments, while ruling out a variety of mix possibilities. Plasma transport parameters affect the 1D buoyancy-drag mix model primarily through its phenomenological drag coefficient as well as the 1D hydro model to which the buoyancy-drag equation is coupled.

Spatial Variability of Sources and Mixing State of Atmospheric Particles in a Metropolitan Area.

Science.gov (United States)

Ye, Qing; Gu, Peishi; Li, Hugh Z; Robinson, Ellis S; Lipsky, Eric; Kaltsonoudis, Christos; Lee, Alex K Y; Apte, Joshua S; Robinson, Allen L; Sullivan, Ryan C; Presto, Albert A; Donahue, Neil M

2018-05-30

Characterizing intracity variations of atmospheric particulate matter has mostly relied on fixed-site monitoring and quantifying variability in terms of different bulk aerosol species. In this study, we performed ground-based mobile measurements using a single-particle mass spectrometer to study spatial patterns of source-specific particles and the evolution of particle mixing state in 21 areas in the metropolitan area of Pittsburgh, PA. We selected sampling areas based on traffic density and restaurant density with each area ranging from 0.2 to 2 km 2 . Organics dominate particle composition in all of the areas we sampled while the sources of organics differ. The contribution of particles from traffic and restaurant cooking varies greatly on the neighborhood scale. We also investigate how primary and aged components in particles mix across the urban scale. Lastly we quantify and map the particle mixing state for all areas we sampled and discuss the overall pattern of mixing state evolution and its implications. We find that in the upwind and downwind of the urban areas, particles are more internally mixed while in the city center, particle mixing state shows large spatial heterogeneity that is mostly driven by emissions. This study is to our knowledge, the first study to perform fine spatial scale mapping of particle mixing state using ground-based mobile measurement and single-particle mass spectrometry.

Biofilm extracellular DNA enhances mixed species biofilms of Staphylococcus epidermidis and Candida albicans.

Science.gov (United States)

Pammi, Mohan; Liang, Rong; Hicks, John; Mistretta, Toni-Ann; Versalovic, James

2013-11-14

Polymicrobial infections are responsible for significant mortality and morbidity in adults and children. Staphylococcus epidermidis and Candida albicans are the most frequent combination of organisms isolated from polymicrobial infections. Vascular indwelling catheters are sites for mixed species biofilm formation and pose a significant risk for polymicrobial infections. We hypothesized that enhancement of biofilms in a mixed species environment increases patient mortality and morbidity. Mixed species biofilms of S. epidermidis and C. albicans were evaluated in vitro and in a subcutaneous catheter infection model in vivo. Mixed species biofilms were enhanced compared to single species biofilms of either S. epidermidis or C. albicans. A mixed species environment increased catheter infection and increased dissemination of S. epidermidis in mice. Microarrays were used to explore differential gene expression of S. epidermidis in the mixed species biofilms. In mixed species biofilms, compared to single species S. epidermidis biofilms, 2.7% of S. epidermidis genes were upregulated and 6% were down regulated. Staphylococcal autolysis repressors lrgA and lrgB were down regulated 36-fold and 27-fold respectively. The role of biofilm extracellular DNA was investigated by quantitation and by evaluating the effects of DNAse in a concentration and time dependent manner. S. epidermidis specific eDNA was increased in mixed species biofilms and further confirmed by degradation with DNAse. Mixed-species biofilms are enhanced and associated with increased S. epidermidis-specific eDNA in vitro and greater systemic dissemination of S. epidermidis in vivo. Down regulation of the lrg operon, a repressor of autolysis, associated with increased eDNA suggests a possible role for bacterial autolysis in mixed species biofilms. Enhancement and systemic dissemination of S. epidermidis may explain adverse outcomes after clinical polymicrobial infections of S. epidermidis and C. albicans.

Biofilm extracellular DNA enhances mixed species biofilms of Staphylococcus epidermidis and Candida albicans

Science.gov (United States)

2013-01-01

Background Polymicrobial infections are responsible for significant mortality and morbidity in adults and children. Staphylococcus epidermidis and Candida albicans are the most frequent combination of organisms isolated from polymicrobial infections. Vascular indwelling catheters are sites for mixed species biofilm formation and pose a significant risk for polymicrobial infections. We hypothesized that enhancement of biofilms in a mixed species environment increases patient mortality and morbidity. Results Mixed species biofilms of S. epidermidis and C. albicans were evaluated in vitro and in a subcutaneous catheter infection model in vivo. Mixed species biofilms were enhanced compared to single species biofilms of either S. epidermidis or C. albicans. A mixed species environment increased catheter infection and increased dissemination of S. epidermidis in mice. Microarrays were used to explore differential gene expression of S. epidermidis in the mixed species biofilms. In mixed species biofilms, compared to single species S. epidermidis biofilms, 2.7% of S. epidermidis genes were upregulated and 6% were down regulated. Staphylococcal autolysis repressors lrgA and lrgB were down regulated 36-fold and 27-fold respectively. The role of biofilm extracellular DNA was investigated by quantitation and by evaluating the effects of DNAse in a concentration and time dependent manner. S. epidermidis specific eDNA was increased in mixed species biofilms and further confirmed by degradation with DNAse. Conclusions Mixed-species biofilms are enhanced and associated with increased S. epidermidis-specific eDNA in vitro and greater systemic dissemination of S. epidermidis in vivo. Down regulation of the lrg operon, a repressor of autolysis, associated with increased eDNA suggests a possible role for bacterial autolysis in mixed species biofilms. Enhancement and systemic dissemination of S. epidermidis may explain adverse outcomes after clinical polymicrobial infections of S

SU-E-T-319: Dosimetric Evaluation of IMRT with Mix-Energy Beam for Deep Seated Targets

Energy Technology Data Exchange (ETDEWEB)

Sharma, S; Manigandan, D; Gandhi, A; Sharma, D; Subramani, V; Chander, S; Julkha, P [Fortis Hospital, Mohali, Punjab (India); Rath, G

2015-06-15

Purpose: IMRT is preferred in the range of 6–10MV X-rays. Partially adding high energy (>10MV) treatment fields, may provide advantage of both higher and lower energies. To study IMRT dose distribution obtained from treatment plans with single (6MV) and mixed-energy (6MV and 15MV) for deep seated targets (separation more than 30cm). Methods: Five patients of carcinoma of cervix were studied using eclipse planning system. Two different dynamic IMRT plans were generated for Varian CL2300C/D linear accelerator; one is by using 6MV X-ray with seven equally spaced coplanar beams. In second plan, 2 lateral oblique fields (gantry angle 102°, 255°) beam energy was modified to 15MV by keeping all other parameters and dose volume constraints constant. Dose prescription for the planning target volume (PTV) was (5040cGy/28f). For plan comparison, dose volume histogram (DVH) was used and PTV coverage index (CI=Target volume covered by prescription dose/Target volume), heterogeneity index (D5/D95), mean dose to organ at risk (OAR) and normal tissue integral dose (NTID, liter-Gray) was also noted. Total monitor unit (MU) required to deliver a plan was also noted. Results: Mixed-energy plan showed a better conformity and CI values were 0.942±0.032 and 0.960±0.040 for single-energy and mixed-energy plan, respectively. In addition, HI value of mixed energy beam is comparable to that of single energy and the values were within 1.084±0.034 and 1.082±0.032 for single energy and mixed-energy plan, respectively. Variation in mean dose to bladder, rectum and bowel were within 1.05%, 0.87% and 0.90%. NTID was lesser for mixed-energy beam due to use of two high-energy fields. NTID were 1573.40±214.60 and 1510.20±249.80 litre-Gray for single energy and mixed-energy plan. MU needed to deliver a plan was similar in both plans and MUs were 238±45 and 237±47. Conclusion: Partial use of 15MV treatment fields in IMRT plan for deep seated targets showed dosimetric advantage over 6MV

Concentrations of the acute phase reactants high-sensitive C-reactive protein and YKL-40 and of interleukin-6 before and after treatment in patients with acromegaly and growth hormone deficiency

DEFF Research Database (Denmark)

Andreassen, Mikkel; Vestergaard, Henrik; Kristensen, Lars Østergaard

2007-01-01

Acromegaly is accompanied by increased cardiovascular mortality and a cluster of proatherogenic risk factors. In the general population, ischaemic heart disease (IHD) is associated with elevated levels of inflammatory markers. The acute phase reactant (APR) C-reactive protein (CRP) has been...... reported to be reduced in acromegaly and increase after treatment, suggesting that excess of GH/IGF-I could have anti-inflammatory effects. This is in accordance with results obtained in patients with growth hormone deficiency (GHD), where increased levels of CRP have been reported....

Lepton mixing in A_5 family symmetry and generalized CP

International Nuclear Information System (INIS)

Li, Cai-Chang; Ding, Gui-Jun

2015-01-01

We study lepton mixing patterns which can be derived from the A_5 family symmetry and generalized CP. We find five phenomenologically interesting mixing patterns for which one column of the PMNS matrix is (√(((5+√5)/10)),(1/(√(5+√5))),(1/(√(5+√5))))"T (the first column of the golden ratio mixing), (√(((5−√5)/10)),(1/(√(5−√5))),(1/(√(5−√5))))"T (the second column of the golden ratio mixing), (1,1,1)"T/√3 or (√5+1,−2,√5−1)"T/4. The three lepton mixing angles are determined in terms of a single real parameter θ, and agreement with experimental data can be achieved for certain values of θ. The Dirac CP violating phase is predicted to be trivial or maximal while Majorana phases are trivial. We construct a supersymmetric model based on A_5 family symmetry and generalized CP. The lepton mixing is exactly the golden ratio pattern at leading order, and the mixing patterns of case III and case IV are reproduced after higher order corrections are considered.

Wave mixing spectroscopy

International Nuclear Information System (INIS)

Smith, R.W.

1980-08-01

Several new aspects of nonlinear or wave mixing spectroscopy were investigated utilizing the polarization properties of the nonlinear output field and the dependence of this field upon the occurrence of multiple resonances in the nonlinear susceptibility. First, it is shown theoretically that polarization-sensitive detection may be used to either eliminate or controllably reduce the nonresonant background in coherent anti-Stokes Raman spectroscopy, allowing weaker Raman resonances to be studied. The features of multi-resonant four-wave mixing are examined in the case of an inhomogeneously broadened medium. It is found that the linewidth of the nonlinear output narrows considerably (approaching the homogeneous width) when the quantum mechanical expressions for the doubly- and triply-resonant susceptibilities are averaged over a Doppler or strain broadened profile. Experimental studies of nonlinear processes in Pr +3 :LaF 3 verify this linewidth narrowing, but indicate that this strain broadened system cannot be treated with a single broadening parameter as in the case of Doppler broadening in a gas. Several susceptibilities are measured from which are deduced dipole matrix elements and Raman polarizabilities related to the 3 H 4 , 3 H 6 , and 3 P 0 levels of the praseodymium ions

Signs of tops from highly mixed stops

Energy Technology Data Exchange (ETDEWEB)

Backović, Mihailo [Center for Cosmology, Particle Physics and Phenomenology - CP3,Universite Catholique de Louvain, Louvain-la-neuve (Belgium); Mariotti, Alberto [Theoretische Natuurkunde and IIHE/ELEM, Vrije Universiteit Brussel,and International Solvay Institutes, Pleinlaan 2, B-1050 Brussels (Belgium); Spannowsky, Michael [Institute for Particle Physics Phenomenology, Department of Physics,Durham University, Durham DH1 3LE (United Kingdom)

2015-06-17

Supersymmetric extensions of the Standard Model with highly mixed squark flavours beyond minimal flavour violation provide interesting scenarios of new physics, which have so far received limited attention. We propose a calculable realization of such scenarios in models of gauge mediation augmented with an extra interaction between the messengers and the up type squark. We compute the supersymmetric spectrum and analyze the flavour physics constraints on such models. In a simplified model approach, we show that scenarios with maximal squark flavour mixing result in interesting phenomenological signatures at the LHC. We show that the model can be probed up to masses of m{sub ũ}≲950 GeV in the single-top event topology at LHC14 with as little as 300 fb{sup −1}. The most distinctive signature of highly mixed scenarios, the same sign positive charge di-top, can be also probed to comparable squark masses at high luminosity LHC14.

CFD simulation on reactor flow mixing phenomena

International Nuclear Information System (INIS)

Kwon, T.S.; Kim, K.H.

2016-01-01

A pre-test calculation for multi-dimensional flow mixing in a reactor core and downcomer has been studied using a CFD code. To study the effects of Reactor Coolant Pump (RCP) and core zone on the boron mixing behaviors in a lower downcomer and core inlet, a 1/5-scale CFD model of flow mixing test facility for the APR+ reference plant was simulated. The flow paths of the 1/5-scale model were scaled down by the linear scaling method. The aspect ratio (L/D) of all flow paths was preserved to 1. To preserve a dynamic similarity, the ratio of Euler number was also preserved to 1. A single phase water flow at low pressure and temperature conditions was considered in this calculation. The calculation shows that the asymmetric effect driven by RCPs shifted the high velocity field to the failed pump's flow zone. The borated water flow zone at the core inlet was also shifted to the failed RCP side. (author)

Single-collision studies of hot atom energy transfer and chemical reaction

International Nuclear Information System (INIS)

Valentini, J.J.

1991-01-01

This report discusses research in the collision dynamics of translationally hot atoms, with funding with DOE for the project ''Single-Collision Studies of Hot Atom Energy Transfer and Chemical Reaction,'' Grant Number DE-FG03-85ER13453. The work reported here was done during the period September 9, 1988 through October 31, 1991. During this period this DOE-funded work has been focused on several different efforts: (1) experimental studies of the state-to-state dynamics of the H + RH → H 2 R reactions where RH is CH 4 , C 2 H 6 , or C 3 H 8 , (2) theoretical (quasiclassical trajectory) studies of hot hydrogen atom collision dynamics, (3) the development of photochemical sources of translationally hot molecular free radicals and characterization of the high resolution CARS spectroscopy of molecular free radicals, (4) the implementation of stimulated Raman excitation (SRE) techniques for the preparation of vibrationally state-selected molecular reactants

Growth and characterization of gel grown pure and mixed iron ...

Indian Academy of Sciences (India)

Unknown

is to grow pure and mixed iron (II)–manganese levo-tartrate crystals by the single diffusion gel growth technique and characterize them by several methods. 2. ... also attracted several researchers to grow different crystals for various ...

Development of Mixed Mode MPI / OpenMP Applications

Directory of Open Access Journals (Sweden)

Lorna Smith

2001-01-01

Full Text Available MPI / OpenMP mixed mode codes could potentially offer the most effective parallelisation strategy for an SMP cluster, as well as allowing the different characteristics of both paradigms to be exploited to give the best performance on a single SMP. This paper discusses the implementation, development and performance of mixed mode MPI / OpenMP applications. The results demonstrate that this style of programming will not always be the most effective mechanism on SMP systems and cannot be regarded as the ideal programming model for all codes. In some situations, however, significant benefit may be obtained from a mixed mode implementation. For example, benefit may be obtained if the parallel (MPI code suffers from: poor scaling with MPI processes due to load imbalance or too fine a grain problem size, memory limitations due to the use of a replicated data strategy, or a restriction on the number of MPI processes combinations. In addition, if the system has a poorly optimised or limited scaling MPI implementation then a mixed mode code may increase the code performance.

Monoclonal antibody fragment removal mediated by mixed mode resins.

Science.gov (United States)

O'Connor, Ellen; Aspelund, Matthew; Bartnik, Frank; Berge, Mark; Coughlin, Kelly; Kambarami, Mutsa; Spencer, David; Yan, Huiming; Wang, William

2017-05-26

Efforts to increase monoclonal antibody expression in cell culture can result in the presence of fragmented species requiring removal in downstream processing. Capto adhere, HEA Hypercel, and PPA Hypercel anion exchange/hydrophobic interaction mixed mode resins were evaluated for their fragment removal capabilities and found to separate large hinge IgG1 antibody fragment (LHF) from monomer. Removal of greater than 75% of LHF population occurred at pH 8 and low conductivity. The mechanism of fragment removal was investigated in two series of experiments. The first experimental series consisted of comparison to chromatographic behavior on corresponding single mode resins. Both single mode anion exchange and hydrophobic interaction resins failed to separate LHF. The second experimental series studied the impact of phase modifiers, ethylene glycol, urea, and arginine on the mixed mode mediated removal. The addition of ethylene glycol decreased LHF removal by half. Further decreases in LHF separation were seen upon incubation with urea and arginine. Therefore, it was discovered that the purification is the result of a mixed mode phenomena dominated by hydrophobic interaction and hydrogen bonding effects. The site of interaction between the LHF and mixed mode resin was determined by chemical labeling of lysine residues with sulfo-NHS acetate. The labeling identified the antibody hinge and light chain regions as mediating the fragment separation. Sequence analysis showed that under separation conditions, a hydrophobic proline patch and hydrogen bonding serine and threonine residues mediate the hinge interaction with the Capto adhere ligand. Additionally, a case study is presented detailing the optimization of fragment removal using Capto adhere resin to achieve purity and yield targets in a manufacturing facility. This study demonstrated that mixed mode resins can be readily integrated into commercial antibody platform processes when additional chromatographic abilities

SEL Hardness Assurance in a Mixed Radiation Field

CERN Document Server

Garcia Alia, Ruben; Danzeca, Salvatore; Ferlet-Cavrois, Veronique; Frost, Christopher; Gaillard, Remi; Mekki, Julien; Saigné, Frédéric; Thornton, Adam; Uznanski, Slawosz; Worbel, Frédéric; CERN. Geneva. ATS Department

2015-01-01

This paper explores the relationship between monoenergetic and mixed-field Single Event Latchup (SEL) cross sections, concluding for components with a very strong energy dependence and highly-energetic environments, test results from monoenergetic or soft mixed-field spectra can significantly underestimate the operational failure rate. We introduce a semi-empirical approach that can be used to evaluate the SEL rate for such environments based on monoenergetic measurements and information or assumptions on the respective sensitive volume and materials surrounding it. We show that the presence of high-Z materials such as tungsten is particularly important in determining the hadron cross section energy dependence for components with relatively large LET thresholds.

Species mixing effects on forest productivity in the Netherlands

NARCIS (Netherlands)

Lu, Huicui

2017-01-01

Many monoculture forests (dominated by a single tree species) have been converted to mixed-species forests (dominated by more than one tree species) in Europe over the last decades. The main reason for this conversion was to increase productivity, including timber production, and enhance other

Two-phase flow and cross-mixing measurements in a rod bundle

International Nuclear Information System (INIS)

Yloenen, A.; Prasser, H.-M.

2011-01-01

The wire-mesh sensor technique has been used for the first time to study two-phase flow and liquid mixing in a rod bundle. A dedicated test facility (SUBFLOW) was constructed at Paul Scherrer Institut (PSI) in a co-operation with the Swiss Federal Institute of Technology (ETH Zurich). Simultaneous injection of salt water as tracer and air bubbles can be used to quantify the enhancement of liquid mixing in two-phase flow when the results are compared with the single-phase mixing experiment with the same test parameters. The second aspect in the current experiments is the two-phase flow in bundle geometry. (author)

In-core LOCA-s: analytical solution for the delayed mixing model for moderator poison concentration

International Nuclear Information System (INIS)

Firla, A.P.

1995-01-01

Solutions to dynamic moderator poison concentration model with delayed mixing under single pressure tube / calandria tube rupture scenario are discussed. Such a model is described by a delay differential equation, and for such equations the standard ways of solution are not directly applicable. In the paper an exact, direct time-domain analytical solution to the delayed mixing model is presented and discussed. The obtained solution has a 'marching' form and is easy to calculate numerically. Results of the numerical calculations based on the analytical solution indicate that for the expected range of mixing times the existing uniform mixing model is a good representation of the moderator poison mixing process for single PT/CT breaks. However, for postulated multi-pipe breaks ( which is very unlikely to occur ) the uniform mixing model is not adequate any more; at the same time an 'approximate' solution based on Laplace transform significantly overpredicts the rate of poison concentration decrease, resulting in excessive increase in the moderator dilution factor. In this situation the true, analytical solution must be used. The analytical solution presented in the paper may also serve as a bench-mark test for the accuracy of the existing poison mixing models. Moreover, because of the existing oscillatory tendency of the solution, special care must be taken in using delay differential models in other applications. (author). 3 refs., 3 tabs., 8 figs

Mixed methods research design for pragmatic psychoanalytic studies.

Science.gov (United States)

Tillman, Jane G; Clemence, A Jill; Stevens, Jennifer L

2011-10-01

Calls for more rigorous psychoanalytic studies have increased over the past decade. The field has been divided by those who assert that psychoanalysis is properly a hermeneutic endeavor and those who see it as a science. A comparable debate is found in research methodology, where qualitative and quantitative methods have often been seen as occupying orthogonal positions. Recently, Mixed Methods Research (MMR) has emerged as a viable "third community" of research, pursuing a pragmatic approach to research endeavors through integrating qualitative and quantitative procedures in a single study design. Mixed Methods Research designs and the terminology associated with this emerging approach are explained, after which the methodology is explored as a potential integrative approach to a psychoanalytic human science. Both qualitative and quantitative research methods are reviewed, as well as how they may be used in Mixed Methods Research to study complex human phenomena.

Investigations on the role of mixed-solvent for improved efficiency in perovskite solar cell

Science.gov (United States)

Singh, Ranbir; Suranagi, Sanjaykumar R.; Kumar, Manish; Shukla, Vivek Kumar

2017-12-01

The morphology of the spin-coated photoactive layer is one of the major factors affecting the performance of perovskite solar cells. In this work, we have employed a mixed-solvent strategy to obtain a high quality MAPbI3 (MA = CH3NH3) perovskite film, without pinholes and reduced grain boundaries. Perovskite films formed with single and mixed-solvents are systematically characterized for their optical, structural, and morphological properties using UV-vis absorption, photoluminescence (PL), X-ray diffraction (XRD), atomic force microscopy (AFM), and scanning electron microscopy (SEM) tools. The power conversion efficiency (PCE) of the devices fabricated using the mixed-solvent showed better performance than the devices made using the single solvent. The best-optimized mixed-solvent perovskite film exhibited a PCE of 15.2% with uniform film coverage on the substrate, better charge generation, and a high hole mobility of 1.16 × 10-4cm2/V s. The disparities in photovoltaic properties have been analyzed with the intensity dependent current density-voltage (J-V), transient photovoltage (TPV), and relationship between photocurrent (Jph) and effective voltage (Veff).

Fast mental states decoding in mixed reality.

Directory of Open Access Journals (Sweden)

Daniele eDe Massari

2014-11-01

Full Text Available The combination of Brain-Computer Interface technology, allowing online monitoring and decoding of brain activity, with virtual and mixed reality systems may help to shape and guide implicit and explicit learning using ecological scenarios. Real-time information of ongoing brain states acquired through BCI might be exploited for controlling data presentation in virtual environments. In this context, assessing to what extent brain states can be discriminated during mixed reality experience is critical for adapting specific data features to contingent brain activity. In this study we recorded EEG data while participants experienced a mixed reality scenario implemented through the eXperience Induction Machine (XIM. The XIM is a novel framework modeling the integration of a sensing system that evaluates and measures physiological and psychological states with a number of actuators and effectors that coherently reacts to the user's actions. We then assessed continuous EEG-based discrimination of spatial navigation, reading and calculation performed in mixed reality, using LDA and SVM classifiers. Dynamic single trial classification showed high accuracy of LDA and SVM classifiers in detecting multiple brain states as well as in differentiating between high and low mental workload, using a 5 s time-window shifting every 200 ms. Our results indicate overall better performance of LDA with respect to SVM and suggest applicability of our approach in a BCI-controlled mixed reality scenario. Ultimately, successful prediction of brain states might be used to drive adaptation of data representation in order to boost information processing in mixed reality.

Effect of Mixing on Microorganism Growth in Loop Bioreactors

Directory of Open Access Journals (Sweden)

A. M. Al Taweel

2012-01-01

Full Text Available The impact of mixing on the promotion of microorganism growth rate has been analyzed using a multiphase forced-circulation pipe-loop reactor model capable of identifying conditions under which it is possible to convert natural gas into Single-Cell Protein. The impact of mixing in the interphase mass transfer was found to exert a critical role in determining the overall productivity of the bioreactor, particularly at the high cell loadings needed to reduce the capital costs associated with the large-scale production needed for the production of relatively low-value SCP in a sustainable manner.

Channel coupling in heavy quarkonia: Energy levels, mixing, widths, and new states

International Nuclear Information System (INIS)

Danilkin, I. V.; Simonov, Yu. A.

2010-01-01

The mechanism of channel coupling via decay products is used to study energy shifts, level mixing as well as the possibility of new near-threshold resonances in cc, bb systems. The Weinberg eigenvalue method is formulated in the multichannel problems, which allows one to describe coupled-channel resonances and wave functions in a unitary way, and to predict new states due to channel coupling. Realistic wave functions for all single-channel states and decay matrix elements computed earlier are exploited, and no new fitting parameters are involved. Examples of level shifts, widths, and mixings are presented; the dynamical origin of X(3872) and the destiny of the single-channel 2 3 P 1 (cc) state are clarified. As a result a sharp and narrow peak in the state with quantum numbers J PC =1 ++ is found at 3.872 GeV, while the single-channel resonance originally around 3.940 GeV becomes increasingly broad and disappears with growing coupling to open channels.

Nanoscale Mixing of Soft Solids

International Nuclear Information System (INIS)

Choi, Soo-Hyung; Lee, Sangwoo; Soto, Haidy E.; Lodge, Timothy P.; Bates, Frank S.

2011-01-01

Assessing the state of mixing on the molecular scale in soft solids is challenging. Concentrated solutions of micelles formed by self-assembly of polystyrene-block-poly(ethylene-alt-propylene) (PS-PEP) diblock copolymers in squalane (C 30 H 62 ) adopt a body-centered cubic (bcc) lattice, with glassy PS cores. Utilizing small-angle neutron scattering (SANS) and isotopic labeling ( 1 H and 2 H (D) polystyrene blocks) in a contrast-matching solvent (a mixture of squalane and perdeuterated squalane), we demonstrate quantitatively the remarkable fact that a commercial mixer can create completely random mixtures of micelles with either normal, PS(H), or deuterium-labeled, PS(D), cores on a well-defined bcc lattice. The resulting SANS intensity is quantitatively modeled by the form factor of a single spherical core. These results demonstrate both the possibility of achieving complete nanoscale mixing in a soft solid and the use of SANS to quantify the randomness.

Microwave-Assisted Solvent-Free Synthesis of Zeolitic Imidazolate Framework-67

Directory of Open Access Journals (Sweden)

Heng Zhang

2016-01-01

Full Text Available A microporous metal-organic framework (MOF, cobalt-based zeolitic imidazolate framework-67 (ZIF-67, was synthesized by the combination of solvent-free hand-mill and microwave irradiation, without any organic solvent and within 30 minutes. The hand-milling process can mix the reactants well by the virtue of high moisture/water absorption capacity of reactants. In addition, the outstanding electromagnetic wave absorption capability of cobalt leads to efficient conversion to MOF structures before carbonization. The obtained ZIF-67 possesses high surface area and micropore volume.

MIXING OF INCOMPATIBLE MATERIALS IN WASTE TANKS TECHNICAL BASIS DOCUMENT

International Nuclear Information System (INIS)

SANDGREN, K.R.

2006-01-01

This document presents onsite radiological, onsite toxicological, and offsite toxicological consequences, risk binning, and control decision results for the mixing of incompatible materials in waste tanks representative accident. Revision 4 updates the analysis to consider bulk chemical additions to single shell tanks (SSTs)

Trichoderma Reesei single cell protein production from rice straw pulp in solid state fermentation

Science.gov (United States)

Zaki, M.; Said, S. D.

2018-04-01

The dependency on fish meal as a major protein source for animal feed can lead toit priceinstability in line with the increasing in meat production and consumption in Indonesia. In order todeal with this problem, an effort to produce an alternative protein sources production is needed. This scenario is possible due to the abundantavailability of agricultural residues such as rice straw whichcould be utilized as substrate for production of single cell proteins as an alternative proteinsource. This work investigated the potential utilization of rice straw pulp and urea mixture as substrate for the production of local Trichoderma reesei single cell protein in solid state fermentation system. Some parameters have been analyzed to evaluate the effect of ratio of rice straw pulp to urea on mixed single cell protein biomass (mixed SCP biomass) composition, such as total crude protein (analyzed by kjedhal method) and lignin content (TAPPI method).The results showed that crude protein content in mixed SCP biomassincreases with the increasing in fermentation time, otherwise it decreases with the increasing insubstrate carbon to nitrogen (C/N) ratio. Residual lignin content in mixed SCP biomass decreases from 7% to 0.63% during fermentationproceeded of 21 days. The highest crude protein content in mixed SCP biomasswas obtained at substrate C/N ratio 20:1 of 25%.

The single-ion anisotropy effects in the mixed-spin ternary-alloy

Science.gov (United States)

Albayrak, Erhan

2018-04-01

The effect of single-ion anisotropy on the thermal properties of the ternary-alloy in the form of ABpC1-p is investigated on the Bethe lattice (BL) in terms of exact recursion relations. The simulation on the BL consists of placing A atoms (spin-1/2) on the odd shells and randomly placing B (spin-3/2) or C (spin-5/2) atoms with concentrations p and 1 - p, respectively, on the even shells. The phase diagrams are calculated in possible planes spanned by the system parameters: temperature, single-ion anisotropy, concentration and ratio of the bilinear interaction parameters for z = 3 corresponding to the honeycomb lattice. It is found that the crystal field drives the system to the lowest possible state therefore reducing the temperatures of the critical lines in agreement with the literature.

The Effect of Diet Mixing on a Nonselective Herbivore.

Directory of Open Access Journals (Sweden)

Sophie Groendahl

Full Text Available The balanced-diet hypothesis states that a diverse prey community is beneficial to consumers due to resource complementarity among the prey species. Nonselective consumer species cannot differentiate between prey items and are therefore not able to actively regulate their diet intake. We thus wanted to test whether the balanced-diet hypothesis is applicable to nonselective consumers. We conducted a laboratory experiment in which a nonselective model grazer, the freshwater gastropod Lymnaea stagnalis, was fed benthic green algae as single species or as a multi-species mixture and quantified the snails' somatic growth rates and shell lengths over a seven-week period. Gastropods fed the mixed diet were found to exhibit a higher somatic growth rate than the average of the snails fed single prey species. However, growth on the multi-species mixture did not exceed the growth rate obtained on the best single prey species. Similar results were obtained regarding the animals' shell height increase over time. The mixed diet did not provide the highest growth rate, which confirms our hypothesis. We thus suggest that the balanced-diet hypothesis is less relevant for non-selective generalist consumers, which needs to be considered in estimates of secondary production.

Growth promotion of peanut (Arachis hypogaea L.) and maize (Zea mays L.) plants by single and mixed cultures of efficient phosphate solubilizing bacteria that are tolerant to abiotic stress and pesticides.

Science.gov (United States)

Anzuay, María Soledad; Ciancio, María Gabriela Ruiz; Ludueña, Liliana Mercedes; Angelini, Jorge Guillermo; Barros, Germán; Pastor, Nicolás; Taurian, Tania

2017-06-01

The aims of this study were, to analyze in vitro phosphate solubilization activity of six native peanut bacteria and to determine the effect of single and mixed inoculation of these bacteria on peanut and maize plants. Ability to produce organic acids and cofactor PQQ, to solubilize FePO 4 and AlPO 4 and phosphatase activity were analyzed. Also, the ability to solubilize phosphate under abiotic stress and in the presence of pesticides of the selected bacteria was determined. The effect of single and mixed bacterial inocula was analyzed on seed germination, maize plant growth and in a crop rotation plant assay with peanut and maize. The six strains produced gluconic acid and five released cofactor PQQ into the medium. All bacteria showed ability to solubilize phosphate from FePO 4 and AlPO 4 and phosphatase activity. The ability of the bacteria to solubilize tricalcium phosphate under abiotic stress and in presence of pesticides indicated encouraging results. Bacterial inoculation on peanut and maize increased seed germination, plant́s growth and P content. Phosphate solubilizing bacteria used in this study showed efficient phosphate mineralizing and solubilization ability and would be potential P-biofertilizers for peanut and maize. Copyright © 2017 Elsevier GmbH. All rights reserved.

Mixing ratio sensor for alcohol mixed fuel

Energy Technology Data Exchange (ETDEWEB)

Miyata, Shigeru; Matsubara, Yoshihiro

1987-08-24

In order to improve the combustion efficiency of an internal combustion engine using gasoline-alcohol mixed fuel and to reduce harmful substance in its exhaust gas, it is necessary to control strictly the air-fuel ratio to be supplied and the ignition timing. In order to detect the mixing ratio of the mixed fuel, a mixing ratio sensor has so far been proposed to detect the above mixing ratio by casting a ray of light to the mixed fuel and utilizing a change of critical angle associated with the change of the composition of the fluid of the mixed fuel. However, because of the arrangement of its transparent substance in the fuel passage with the sealing material in between, this sensor invited the leakage of the fluid due to deterioration of the sealing material, etc. and its cost became high because of too many parts to be assembled. In view of the above, in order to reduce the number of parts, to lower the cost of parts and the assembling cost and to secure no fluid leakage from the fuel passage, this invention formed the above fuel passage and the above transparent substance both concerning the above mixing ratio sensor in an integrated manner using light transmitting resin. (3 figs)

High-dose nifuratel for simple and mixed aerobic vaginitis: A single-center prospective open-label cohort study.

Science.gov (United States)

Liang, Qian; Li, Nan; Song, Shurong; Zhang, Aihua; Li, Ni; Duan, Ying

2016-10-01

The efficacy and safety of two nifuratel dosages for the treatment of aerobic vaginitis (AV) were compared. This was a prospective open-label cohort study of patients diagnosed and treated at the Tianjin Third Central Hospital between January 2012 and December 2013. The co-presence of bacterial vaginosis (BV), vulvovaginal candidiasis (VVC), or/and trichomonal vaginitis (TV; mixed AV) was determined. Patients were randomized to nifuratel-500 (500 mg nifuratel, intravaginal, 10 days) or nifuratel-250 (250 mg nifuratel, intravaginal, 10 days), and followed-up for three to seven days after treatment completion. Primary and secondary outcomes were recovery rate and adverse events, respectively. The study included 142 patients with AV. Age was not significantly different between the groups (n = 71 each), and disease distribution was identical: 29 (40.85%) simple AV and 42 (59.15%) mixed AV (AV + BV, 42.86 %; AV + VVC, 30.95%; AV + TV, 26.19%). In patients with simple AV, the recovery rate did not differ significantly between the nifuratel-500 (26/29, 89.66%) and nifuratel-250 (22/29, 75.86%) groups. In patients with mixed AV, recovery rates were significantly higher in the nifuratel-500 than in the nifuratel-250 group (AV + BV, 88.89% vs 50.00 %; AV + VVC, 76.92 % vs 30.77 %; AV + TV, 90.91 % vs 36.36%; all P < 0.05). Only one patient (nifuratel-500) reported an adverse event (mild anaphylactic reaction). Nifuratel 500 mg showed good clinical efficacy for the treatment of AV, particularly mixed AV, and is superior to the 250 mg dosage in the treatment of mixed AV. © 2016 Japan Society of Obstetrics and Gynecology.

[Case-mix index and length of hospitalization].

Science.gov (United States)

D'Andrea, V; Catania, A; Di Matteo, F M; Savino, G; Greco, R; Di Marco, C; De Antoni, E

2010-05-01

The ACG (Adjusted Clinical Groups) case-mix system is a classification method of diseases of patients, focused on the person. Depending on the pattern of these morbid conditions, the ACG system assigns each patient to a single group (an ACG group), which allows to capture the effects of a group of diseases in estimates of resource use. Diseases are classified into a diagnostic group (ADG) according to 5 clinical dimensions: duration (acute, recurrent or chronic), severity (minor/major vs stable/unstable), diagnostic assessment (symptoms vs diseases), etiology (infectious, traumatic or other), specialty (medical, surgical, obstetric, ...). All diseases can be classified into these dimensions and into one of 32 groups. The ACG case-mix system uses an algorithm to classify each patient into one of 93 ACG categories. Each person is assigned to an ACG according to his ADG combination, his age and his gender. With the repayment system "case-mix", surgery has become central for all great hospitals in virtue of its great productive potential. The case-mix index is one of the factors which influence the duration of hospitalization. The case-mix system has emphasized the importance of the duration of hospitalization, encouraging the planning of programs in order to discharge patients early after surgical operations. It has also stimulated the surgical activity in operating units with "budget" forecasts in which resources are provided according to an expected level of specialist surgery.

A novel extended architecture with 4 6·6 4 topology based on mixed-valence Wells-Dawson arsenotungstate and mixed-ligand Cu(I) units

Science.gov (United States)

Tong, Ruizhan; Ren, Xiaoyu; Li, Zuoxi; Liu, Bin; Hu, Huaiming; Xue, Ganglin; Fu, Feng; Wang, Jiwu

2010-09-01

A novel inorganic-organic hybrid compound based on mixed-valence Wells-Dawson arsenotungstate and mixed-ligand Cu(I) units, Cu 8I(imi) 4(bpy) 6(H 2O)[As 2VW 2VW 16VlO 62]·2H 2O ( 1) (bpy=4,4'-bipydine; imi=imidazole), has been hydrothermally synthesized and characterized by elemental analysis, IR spectroscopy, thermal gravimetric analysis, luminescent spectrum and single crystal X-ray diffraction. Single-crystal X-ray diffraction revealed that four terminal and three bridging oxygen atoms of the Wells-Dawson cluster are coordinated to Cu(I) ions and form an unprecedented hepta-supporting polyoxometalate. The functionalized arsenotungstates are further connected by two kinds of tridentate linkers, Imi-Cu-(bpy)-Cu-(bpy)-Cu-(bpy)-Cu-Imi and Imi-Cu-(bpy)-Cu-(bpy)-Cu-H 2O, to construct a 3D framework with 4 6·6 4 topology. The hybrid material has an intense emission at about 397 nm.

Turbulent Mixing of Primary and Secondary Flow Streams in a Rocket-Based Combined Cycle Engine

Science.gov (United States)

Cramer, J. M.; Greene, M. U.; Pal, S.; Santoro, R. J.; Turner, Jim (Technical Monitor)

2002-01-01

This viewgraph presentation gives an overview of the turbulent mixing of primary and secondary flow streams in a rocket-based combined cycle (RBCC) engine. A significant RBCC ejector mode database has been generated, detailing single and twin thruster configurations and global and local measurements. On-going analysis and correlation efforts include Marshall Space Flight Center computational fluid dynamics modeling and turbulent shear layer analysis. Potential follow-on activities include detailed measurements of air flow static pressure and velocity profiles, investigations into other thruster spacing configurations, performing a fundamental shear layer mixing study, and demonstrating single-shot Raman measurements.

Combining cationic and anionic mixed-mode sorbents in a single cartridge to extract basic and acidic pharmaceuticals simultaneously from environmental waters.

Science.gov (United States)

Salas, Daniela; Borrull, Francesc; Fontanals, Núria; Marcé, Rosa Maria

2018-01-01

The aim of the present study is to broaden the applications of mixed-mode ion-exchange solid-phase extraction sorbents to extract both basic and acidic compounds simultaneously by combining the sorbents in a single cartridge and developing a simplified extraction procedure. Four different cartridges containing negative and positive charges in the same configuration were evaluated and compared to extract a group of basic, neutral, and acidic pharmaceuticals selected as model compounds. After a thorough optimization of the extraction conditions, the four different cartridges showed to be capable of retaining basic and acidic pharmaceuticals simultaneously through ionic interactions, allowing the introduction of a washing step with 15 mL methanol to eliminate interferences retained by hydrophobic interactions. Using the best combined cartridge, a method was developed, validated, and further applied to environmental waters to demonstrate that the method is promising for the extraction of basic and acidic compounds from very complex samples.

Mixed-Methods Design in Biology Education Research: Approach and Uses.

Science.gov (United States)

Warfa, Abdi-Rizak M

Educational research often requires mixing different research methodologies to strengthen findings, better contextualize or explain results, or minimize the weaknesses of a single method. This article provides practical guidelines on how to conduct such research in biology education, with a focus on mixed-methods research (MMR) that uses both quantitative and qualitative inquiries. Specifically, the paper provides an overview of mixed-methods design typologies most relevant in biology education research. It also discusses common methodological issues that may arise in mixed-methods studies and ways to address them. The paper concludes with recommendations on how to report and write about MMR. © 2016 L. A.-R. M. Warfa. CBE—Life Sciences Education © 2016 The American Society for Cell Biology. This article is distributed by The American Society for Cell Biology under license from the author(s). It is available to the public under an Attribution–Noncommercial–Share Alike 3.0 Unported Creative Commons License (http://creativecommons.org/licenses/by-nc-sa/3.0).

Optics of Water Cloud Droplets Mixed with Black-Carbon Aerosols

Science.gov (United States)

Mishchenko, Michael I.; Liu, Li; Cairns, Brian; Mackowski, Daniel W.

2014-01-01

We use the recently extended superposition T-matrix method to calculate scattering and absorption properties of micrometer-sized water droplets contaminated by black carbon. Our numerically exact results reveal that, depending on the mode of soot-water mixing, the soot specific absorption can vary by a factor exceeding 6.5. The specific absorption is maximized when the soot material is quasi-uniformly distributed throughout the droplet interior in the form of numerous small monomers. The range of mixing scenarios captured by our computations implies a wide range of remote sensing and radiation budget implications of the presence of black carbon in liquid-water clouds. We show that the popular Maxwell-Garnett effective-medium approximation can be used to calculate the optical cross sections, single-scattering albedo, and asymmetry parameter for the quasi-uniform mixing scenario, but is likely to fail in application to other mixing scenarios and in computations of the elements of the scattering matrix.

"It All depends...": Middle School Teachers Evaluate Single-Sex Classes

Science.gov (United States)

Spielhagen, Frances R.

2011-01-01

This mixed-methods study explored the effectiveness of single-sex classes according to key stakeholders in this educational reform--the teachers who choose or are hired to teach in single-sex classes and schools. Specifically, this study examined the on-the-ground experiences of middle school teachers as they attempted to implement a relatively…

In situ enhanced soil mixing. Innovative technology summary report

International Nuclear Information System (INIS)

1996-02-01

In Situ Enhanced Soil Mixing (ISESM) is a treatment technology that has been demonstrated and deployed to remediate soils contaminated with volatile organic compounds (VOCs). The technology has been developed by industry and has been demonstrated with the assistance of the U.S. Department of Energy's Office of Science and Technology and the Office of Environmental Restoration. The technology is particularly suited to shallow applications, above the water table, but can be used at greater depths. ISESM technologies demonstrated for this project include: (1) Soil mixing with vapor extraction combined with ambient air injection. [Contaminated soil is mixed with ambient air to vaporize volatile organic compounds (VOCs). The mixing auger is moved up and down to assist in removal of contaminated vapors. The vapors are collected in a shroud covering the treatment area and run through a treatment unit containing a carbon filter or a catalytic oxidation unit with a wet scrubber system and a high efficiency particulate air (HEPA) filter.] (2) soil mixing with vapor extraction combined with hot air injection [This process is the same as the ambient air injection except that hot air or steam is injected.] (3) soil mixing with hydrogen peroxide injection [Contaminated soil is mixed with ambient air that contains a mist of diluted hydrogen peroxide (H 2 O 2 ) solution. The H 2 O 2 solution chemically oxidizes the VOCs to carbon dioxide (CO 2 ) and water.] (4) soil mixing with grout injection for solidification/stabilization [Contaminated soil is mixed as a cement grout is injected under pressure to solidify and immobilize the contaminated soil in a concrete-like form.] The soils are mixed with a single-blade auger or with a combination of augers ranging in diameter from 3 to 12 feet

Sandwich-type mixed tetrapyrrole rare-earth triple-decker compounds. Effect of the coordination geometry on the single-molecule-magnet nature.

Science.gov (United States)

Kan, Jinglan; Wang, Hailong; Sun, Wei; Cao, Wei; Tao, Jun; Jiang, Jianzhuang

2013-08-05

Employment of the raise-by-one step method starting from M(TClPP)(acac) (acac = monoanion of acetylacetone) and [Pc(OPh)8]M'[Pc(OPh)8] led to the isolation and free modulation of the two rare-earth ions in the series of four mixed tetrapyrrole dysprosium sandwich complexes {(TClPP)M[Pc(OPh)8]M'[Pc(OPh)8]} [1-4; TClPP = dianion of meso-tetrakis(4-chlorophenyl)porphyrin; Pc(OPh)8 = dianion of 2,3,9,10,16,17,23,24-octa(phenoxyl)phthalocyanine; M-M' = Dy-Dy, Y-Dy, Dy-Y, and Y-Y]. Single-crystal X-ray diffraction analysis reveals different octacoordination geometries for the two metal ions in terms of the twist angle (defined as the rotation angle of one coordination square away from the eclipsed conformation with the other) between the two neighboring tetrapyrrole rings for the three dysprosium-containing isostructural triple-decker compounds, with the metal ion locating between an inner phthalocyanine ligand and an outer porphyrin ligand with a twist angle of 9.64-9.90° and the one between two phthalocyanine ligands of 25.12-25.30°. Systematic and comparative studies over the magnetic properties reveal magnetic-field-induced single-molecule magnet (SMM), SMM, and non-SMM nature for 1-3, respectively, indicating the dominant effect of the coordination geometry of the spin carrier, instead of the f-f interaction, on the magnetic properties. The present result will be helpful for the future design and synthesis of tetrapyrrole lanthanide SMMs with sandwich molecular structures.

Synthesis of (U,Zr)C solid solutions under exothermic conditions

International Nuclear Information System (INIS)

Wang, L.L.; Moore, H.G.; Gladson, J.W.

1993-01-01

The reactions of forming (U,Zr)C solid solutions from their elemental components or similarly less stable reactants such as UC 2 are strongly exothermic due to the high stability of these solid solutions. A simple approach of utilizing this heat of formation energy to assist the solid solution reaction process is to intimately mix the less stable reactant powders and then pressed them into a compact. The compact is then heated to the ignition temperature of the reaction. The feasibility of this reaction method to synthesize (U,Zr)C solid solutions has been demonstrated in this study. The preliminary results also show that both the initial composition and the heating rate have a significant effect on the nature of the reaction process. As expected the degree of powder mixing was also found to affect the completeness of the reaction

Effect of fiber positioning on mixed-mode fracture of interfacial debonding in composites

DEFF Research Database (Denmark)

Ashouri Vajari, Danial; Sørensen, Bent F.; Legarth, Brian Nyvang

2015-01-01

along the interface is due to mixed mode I/II fracture. The aim of this study is to explore ways to stabilize the early stage of debonding so that it becomes possible to determine the mixed mode interfacial fracture properties for the entire mode-mixity range by in-situ observations. Therefore...... instead of a single fiber in order to ease the characterization of interfacial properties. [All rights reserved Elsevier]....

Mixed field dose equivalent measuring instruments

International Nuclear Information System (INIS)

Brackenbush, L.W.; McDonald, J.C.; Endres, G.W.R.; Quam, W.

1985-01-01

In the past, separate instruments have been used to monitor dose equivalent from neutrons and gamma rays. It has been demonstrated that it is now possible to measure simultaneously neutron and gamma dose with a single instrument, the tissue equivalent proportional counter (TEPC). With appropriate algorithms dose equivalent can also be determined from the TEPC. A simple ''pocket rem meter'' for measuring neutron dose equivalent has already been developed. Improved algorithms for determining dose equivalent for mixed fields are presented. (author)

Single oral dose toxicity test of polycalcium, a mixed composition of polycan and calcium lactate-gluconate 1:9 (G/G) in SD rat.

Science.gov (United States)

Kim, Joo-Wan; Choi, Jae-Suk; Ha, Yu-Mi; Choi, In Soon; Kim, Ki-Young; Cho, Hyung-rae; Rha, Chae-hun; Ku, Sae-Kwang

2013-11-01

The object of this study was to obtain acute oral toxicity information of Polycalcium, a mixed composition of Polycan and Calcium lactate-gluconate 1:9 (g/g), in Sprague-Dawely (SD) rats. In order to investigate the toxicity and identify target organs, Polycalcium were once orally administered to female and male SD rats at dose levels of 2000, 1000, 500 and 0 (control) mg/kg body weights. The mortality, changes on body weight and clinical signs were monitored during 14 days after treatment with gross observation, changes on the organ weights and histopathology of principle organs and treatment sites based on the recommendation of KFDA Guidelines [2009-116, 2009]. As the results of single oral treatment of Polycalcium, no treatment related mortalities were observed within 14 days after end of treatment up to 2000 mg/kg, the limited dosage of rodents in the both genders. In addition, no Polycalcium treatment related changes on the body and organ weights, clinical signs, necropsy and histopathological findings were detected. The results obtained in this study suggest that the Polycalcium is non-toxic in rats. The LD50 and approximate LD in rats after single oral dose of Polycalcium were considered over 2000 mg/kg in both female and male, respectively.

Hybrid framework for the simulation of stochastic chemical kinetics

International Nuclear Information System (INIS)

Duncan, Andrew; Erban, Radek; Zygalakis, Konstantinos

2016-01-01

Stochasticity plays a fundamental role in various biochemical processes, such as cell regulatory networks and enzyme cascades. Isothermal, well-mixed systems can be modelled as Markov processes, typically simulated using the Gillespie Stochastic Simulation Algorithm (SSA) [25]. While easy to implement and exact, the computational cost of using the Gillespie SSA to simulate such systems can become prohibitive as the frequency of reaction events increases. This has motivated numerous coarse-grained schemes, where the “fast” reactions are approximated either using Langevin dynamics or deterministically. While such approaches provide a good approximation when all reactants are abundant, the approximation breaks down when one or more species exist only in small concentrations and the fluctuations arising from the discrete nature of the reactions become significant. This is particularly problematic when using such methods to compute statistics of extinction times for chemical species, as well as simulating non-equilibrium systems such as cell-cycle models in which a single species can cycle between abundance and scarcity. In this paper, a hybrid jump-diffusion model for simulating well-mixed stochastic kinetics is derived. It acts as a bridge between the Gillespie SSA and the chemical Langevin equation. For low reactant reactions the underlying behaviour is purely discrete, while purely diffusive when the concentrations of all species are large, with the two different behaviours coexisting in the intermediate region. A bound on the weak error in the classical large volume scaling limit is obtained, and three different numerical discretisations of the jump-diffusion model are described. The benefits of such a formalism are illustrated using computational examples.

Hybrid framework for the simulation of stochastic chemical kinetics

Science.gov (United States)

Duncan, Andrew; Erban, Radek; Zygalakis, Konstantinos

2016-12-01

Stochasticity plays a fundamental role in various biochemical processes, such as cell regulatory networks and enzyme cascades. Isothermal, well-mixed systems can be modelled as Markov processes, typically simulated using the Gillespie Stochastic Simulation Algorithm (SSA) [25]. While easy to implement and exact, the computational cost of using the Gillespie SSA to simulate such systems can become prohibitive as the frequency of reaction events increases. This has motivated numerous coarse-grained schemes, where the "fast" reactions are approximated either using Langevin dynamics or deterministically. While such approaches provide a good approximation when all reactants are abundant, the approximation breaks down when one or more species exist only in small concentrations and the fluctuations arising from the discrete nature of the reactions become significant. This is particularly problematic when using such methods to compute statistics of extinction times for chemical species, as well as simulating non-equilibrium systems such as cell-cycle models in which a single species can cycle between abundance and scarcity. In this paper, a hybrid jump-diffusion model for simulating well-mixed stochastic kinetics is derived. It acts as a bridge between the Gillespie SSA and the chemical Langevin equation. For low reactant reactions the underlying behaviour is purely discrete, while purely diffusive when the concentrations of all species are large, with the two different behaviours coexisting in the intermediate region. A bound on the weak error in the classical large volume scaling limit is obtained, and three different numerical discretisations of the jump-diffusion model are described. The benefits of such a formalism are illustrated using computational examples.

Hybrid framework for the simulation of stochastic chemical kinetics

Energy Technology Data Exchange (ETDEWEB)

Duncan, Andrew, E-mail: a.duncan@imperial.ac.uk [Department of Mathematics, Imperial College, South Kensington Campus, London, SW7 2AZ (United Kingdom); Erban, Radek, E-mail: erban@maths.ox.ac.uk [Mathematical Institute, University of Oxford, Radcliffe Observatory Quarter, Woodstock Road, Oxford, OX2 6GG (United Kingdom); Zygalakis, Konstantinos, E-mail: k.zygalakis@ed.ac.uk [School of Mathematics, University of Edinburgh, Peter Guthrie Tait Road, Edinburgh, EH9 3FD (United Kingdom)

2016-12-01

Stochasticity plays a fundamental role in various biochemical processes, such as cell regulatory networks and enzyme cascades. Isothermal, well-mixed systems can be modelled as Markov processes, typically simulated using the Gillespie Stochastic Simulation Algorithm (SSA) [25]. While easy to implement and exact, the computational cost of using the Gillespie SSA to simulate such systems can become prohibitive as the frequency of reaction events increases. This has motivated numerous coarse-grained schemes, where the “fast” reactions are approximated either using Langevin dynamics or deterministically. While such approaches provide a good approximation when all reactants are abundant, the approximation breaks down when one or more species exist only in small concentrations and the fluctuations arising from the discrete nature of the reactions become significant. This is particularly problematic when using such methods to compute statistics of extinction times for chemical species, as well as simulating non-equilibrium systems such as cell-cycle models in which a single species can cycle between abundance and scarcity. In this paper, a hybrid jump-diffusion model for simulating well-mixed stochastic kinetics is derived. It acts as a bridge between the Gillespie SSA and the chemical Langevin equation. For low reactant reactions the underlying behaviour is purely discrete, while purely diffusive when the concentrations of all species are large, with the two different behaviours coexisting in the intermediate region. A bound on the weak error in the classical large volume scaling limit is obtained, and three different numerical discretisations of the jump-diffusion model are described. The benefits of such a formalism are illustrated using computational examples.

Mixed methods in psychotherapy research: A review of method(ology) integration in psychotherapy science.

Science.gov (United States)

Bartholomew, Theodore T; Lockard, Allison J

2018-06-13

Mixed methods can foster depth and breadth in psychological research. However, its use remains in development in psychotherapy research. Our purpose was to review the use of mixed methods in psychotherapy research. Thirty-one studies were identified via the PRISMA systematic review method. Using Creswell & Plano Clark's typologies to identify design characteristics, we assessed each study for rigor and how each used mixed methods. Key features of mixed methods designs and these common patterns were identified: (a) integration of clients' perceptions via mixing; (b) understanding group psychotherapy; (c) integrating methods with cases and small samples; (d) analyzing clinical data as qualitative data; and (e) exploring cultural identities in psychotherapy through mixed methods. The review is discussed with respect to the value of integrating multiple data in single studies to enhance psychotherapy research. © 2018 Wiley Periodicals, Inc.

Evaluation of the glycemic indices of three commonly eaten mixed meals in Okada, Edo State

OpenAIRE

Omage, Kingsley; Omage, Sylvia O.

2017-01-01

Abstract People do not generally eat single or individual meals; rather they eat mixed meals, consisting of two or more individual meals. These mixed meals usually have glycemic indices which differ from that of the individual food type. This study was aimed at evaluating the glycemic indices of three commonly consumed mixed meals eaten in Okada; rice and beans (test food 1), rice and plantain (test food 2), beans and plantain (test food 3). Two hundred and forty healthy subjects aged between...

Deep amplicon sequencing reveals mixed phytoplasma infection within single grapevine plants

DEFF Research Database (Denmark)

Nicolaisen, Mogens; Contaldo, Nicoletta; Makarova, Olga

2011-01-01

The diversity of phytoplasmas within single plants has not yet been fully investigated. In this project, deep amplicon sequencing was used to generate 50,926 phytoplasma sequences from 11 phytoplasma-infected grapevine samples from a PCR amplicon in the 5' end of the 16S region. After clustering ...

Antibiofilm Effect of DNase against Single and Mixed Species Biofilm

Science.gov (United States)

Sharma, Komal

2018-01-01

Biofilms are aggregates of microorganisms that coexist in socially coordinated micro-niche in a self-produced polymeric matrix on pre-conditioned surfaces. The biofilm matrix reduces the efficacy of antibiofilm strategies. DNase degrades the extracellular DNA (e-DNA) present in the matrix, rendering the matrix weak and susceptible to antimicrobials. In the current study, the effect of DNase I was evaluated during biofilm formation (pre-treatment), on preformed biofilms (post-treatment) and both (dual treatment). The DNase I pre-treatment was optimized for P. aeruginosa PAO1 (model biofilm organism) at 10 µg/mL and post-treatment at 10 µg/mL with 15 min of contact duration. Inclusion of Mg2+ alongside DNase I post-treatment resulted in 90% reduction in biofilm within only 5 min of contact time (irrespective of age of biofilm). On extension of these findings, DNase I was found to be less effective against mixed species biofilm than individual biofilms. DNase I can be used as potent antibiofilm agent and with further optimization can be effectively used for biofilm prevention and reduction in situ. PMID:29562719

Extrusion-mixing compared with hand-mixing of polyether impression materials?

Science.gov (United States)

McMahon, Caroline; Kinsella, Daniel; Fleming, Garry J P

2010-12-01

The hypotheses tested were two-fold (a) whether altering the base:catalyst ratio influences working time, elastic recovery and strain in compression properties of a hand-mixed polyether impression material and (b) whether an extrusion-mixed polyether impression material would have a significant advantage over a hand-mixed polyether impression material mixed to the optimum base:catalyst ratio. The polyether was hand-mixed at the optimum (manufacturers recommended) base:catalyst ratios (7:1) and further groups were made by increasing or decreasing the catalyst length by 25%. Additionally specimens were also made from an extrusion-mixed polyether impression material and compared with the optimum hand-mixed base:catalyst ratio. A penetrometer assembly was used to measure the working time (n=5). Five cylindrical specimens for each hand-mixed and extrusion mixed group investigated were employed for elastic recovery and strain in compression testing. Hand-mixing polyether impression materials with 25% more catalyst than that recommended significantly decreased the working time while hand-mixing with 25% less catalyst than that recommended significantly increased the strain in compression. The extrusion-mixed polyether impression material provided similar working time, elastic recovery and strain in compression to the hand-mixed polyether mixed at the optimum base:catalyst ratio.

Force-induced chemical reactions on the metal centre in a single metalloprotein molecule

Science.gov (United States)

Zheng, Peng; Arantes, Guilherme M.; Field, Martin J.; Li, Hongbin

2015-01-01

Metalloproteins play indispensable roles in biology owing to the versatile chemical reactivity of metal centres. However, studying their reactivity in many metalloproteins is challenging, as protein three-dimensional structure encloses labile metal centres, thus limiting their access to reactants and impeding direct measurements. Here we demonstrate the use of single-molecule atomic force microscopy to induce partial unfolding to expose metal centres in metalloproteins to aqueous solution, thus allowing for studying their chemical reactivity in aqueous solution for the first time. As a proof-of-principle, we demonstrate two chemical reactions for the FeS4 centre in rubredoxin: electrophilic protonation and nucleophilic ligand substitution. Our results show that protonation and ligand substitution result in mechanical destabilization of the FeS4 centre. Quantum chemical calculations corroborated experimental results and revealed detailed reaction mechanisms. We anticipate that this novel approach will provide insights into chemical reactivity of metal centres in metalloproteins under biologically more relevant conditions. PMID:26108369

Plasma streams mixing in two-channel t-shaped magnetic filter

International Nuclear Information System (INIS)

Aksyonov, D.S.; Aksenov, I.I.; Luchaninov, A.A.; Reshetnyak, E.N.; Strel'nitskij, V.E.

2011-01-01

Ti-Al-N films were deposited by vacuum arc method. T-shaped magnetic filter with two channels was used for films preparation. Deposition was performed after aluminum and titanium separate plasma streams from two plasma sources were mixed into single one inside plasma duct having weakened magnetic field near its output. Obtained films have uniform distribution of composition and thickness on 180 mm diameter substrate surface. It was found that mixing and homogenization degree depends on nitrogen pressure, output magnetic field intensity and output- to-substrate distance. Film self-sputtering and aluminum preferential sputtering were observed for elevated negative substrate bias potentials.

Pore Structure Control of Ordered Mesoporous Silica Film Using Mixed Surfactants

Directory of Open Access Journals (Sweden)

Tae-Jung Ha

2011-01-01

Full Text Available Materials with nanosized and well-arranged pores have been researched actively in order to be applied to new technology fields. Especially, mesoporous material containing various pore structures is expected to have different pore structure. To form a mixed pore structure, ordered mesoporous silica films were prepared with a mixture of surfactant; Brij-76 and P-123 block copolymer. In mixed surfactant system, mixed pore structure was observed in the region of P-123/(Brij-76 + P-123 with about 50.0 wt.% while a single pore structure was observed in regions which have large difference in ratio between Brij-76 and P-123 through the X-ray diffraction analysis. Regardless of surfactant ratio, porosity was retained almost the same. It is expected that ordered mesoporous silica film with mixed pore structure can be one of the new materials which has distinctive properties.

Photon-Pair Sources Based on Intermodal Four-Wave Mixing in Few-Mode Fibers

Directory of Open Access Journals (Sweden)

Karsten Rottwitt

2018-05-01

Full Text Available Four-wave mixing in optical fibers has been proven to have many applications within processing of classical optical signals. In addition, recent developments in multimode fibers have made it possible to achieve the necessary phase-matching for efficient four-wave mixing over a very wide bandwidth. Thus, the combination of multimode fiber optics and four-wave mixing is very attractive for various applications. This is especially the case for applications in quantum communication, for example in photon-pair generation. This is the subject of this work, where we discuss the impact of fluctuations in core radius on the quality of the heralded single-photon states and demonstrate experimental results of intermodal spontaneous four-wave mixing for photon-pair generation.

Third family corrections to tri-bimaximal lepton mixing and a new sum rule

International Nuclear Information System (INIS)

Antusch, Stefan; King, Stephen F.; Malinsky, Michal

2009-01-01

We investigate the theoretical stability of the predictions of tri-bimaximal neutrino mixing with respect to third family wave-function corrections. Such third family wave-function corrections can arise from either the canonical normalisation of the kinetic terms or renormalisation group running effects. At leading order both sorts of corrections can be subsumed into a single universal parameter. For hierarchical neutrinos, this leads to a new testable lepton mixing sum rule s=rcosδ+2/3 a (where s,r,a describe the deviations of solar, reactor and atmospheric mixing angles from their tri-bimaximal values, and δ is the observable Dirac CP phase) which is stable under all leading order third family wave-function corrections, as well as Cabibbo-like charged lepton mixing effects

Using Aspen simulation package to determine solubility of mixed salts in TRU waste evaporator bottoms

Energy Technology Data Exchange (ETDEWEB)

Hatchell, J.L.

1998-03-01

Nitric acid from plutonium process waste is a candidate for waste minimization by recycling. Process simulation software packages, such as Aspen, are valuable tools to estimate how effective recovery processes can be, however, constants in equations of state for many ionic components are not in their data libraries. One option is to combine single salt solubility`s in the Aspen model for mixed salt system. Single salt solubilities were regressed in Aspen within 0.82 weight percent of literature values. These were combined into a single Aspen model and used in the mixed salt studies. A simulated nitric acid waste containing mixed aluminum, calcium, iron, magnesium and sodium nitrate was tested to determine points of solubility between 25 and 100 C. Only four of the modeled experimental conditions, at 50 C and 75 C, produced a saturated solution. While experimental results indicate that sodium nitrate is the first salt to crystallize out, the Aspen computer model shows that the most insoluble salt, magnesium nitrate, the first salt to crystallize. Possible double salt formation is actually taking place under experimental conditions, which is not captured by the Aspen model.

Mixed-methods research in pharmacy practice: basics and beyond (part 1).

Science.gov (United States)

Hadi, Muhammad Abdul; Alldred, David Phillip; Closs, S José; Briggs, Michelle

2013-10-01

This is the first of two papers which explore the use of mixed-methods research in pharmacy practice. In an era of evidence-based medicine and policy, high-quality research evidence is essential for the development of effective pharmacist-led services. Over the past decade, the use of mixed-methods research has become increasingly common in healthcare, although to date its use has been relatively limited in pharmacy practice research. In this article, the basic concepts of mixed-methods research including its definition, typologies and advantages in relation to pharmacy practice research are discussed. Mixed-methods research brings together qualitative and quantitative methodologies within a single study to answer or understand a research problem. There are a number of mixed-methods designs available, but the selection of an appropriate design must always be dictated by the research question. Importantly, mixed-methods research should not be seen as a 'tool' to collect qualitative and quantitative data, rather there should be some degree of 'integration' between the two data sets. If conducted appropriately, mixed-methods research has the potential to generate quality research evidence by combining strengths and overcoming the respective limitations of qualitative and quantitative methodologies. © 2012 Royal Pharmaceutical Society.

Split-step scheme for photon-pair generation through spontaneous four-wave mixing

DEFF Research Database (Denmark)

Koefoed, Jacob Gade; Christensen, Jesper Bjerge; Rottwitt, Karsten

2017-01-01

The rapid development of quantum information technology requires the ability to reliably create and distribute single photons [1]. Photon-pair production through spontaneous four-wave mixing (SpFWM) allows heralded single photons to be generated at communication wavelengths and in fiber, compatible...... with conventional communication systems, with small losses. Creating single photons in desired quantum states require careful design of waveguide structures. This is greatly facilitated by a general numerical approach as presented here. Additionally, such a numerical approach allows detailed analysis of real...... systems where all relevent effects are included....

Non-mix fragrances are top sensitizers in consecutive dermatitis patients – a cross-sectional study of the 26 EU-labelled fragrance allergens

DEFF Research Database (Denmark)

Bennike, Niels H.; Zachariae, Claus; Johansen, Jeanne D.

2017-01-01

Background: For cosmetics, it is mandatory to label 26 fragrance substances, including all constituents of fragrance mix I (FM I) and fragrance mix II (FM II). Earlier reports have not included oxidized R-limonene [hydroperoxides of R-limonene (Lim-OOH)] and oxidized linalool [hydroperoxides...... patients were ‘FM II-negative but constituent-positive’ than ‘FM I-negative but constituent-positive’ (12.4% versus 3.2%, p = 0.0008). Conclusions: Non-mix fragrances are the most important single fragrance allergens among consecutive patients. The test concentration of the single FM I constituents should...

Pb and Hg heavy metal tolerance of single- and mixedspecies biofilm (Rhodotorula mucilaginosa and Escherichia coli

Directory of Open Access Journals (Sweden)

Buzejić Anica

2016-01-01

Full Text Available The aim of this study was to examine heavy metal tolerance (lead (Pb2+ and mercury (Hg2+ of single- and mixed-species biofilms, formed by yeast Rhodotorula mucilaginosa and bacteria Escherichia coli LM1. Single- and mixed-species biofilms were quantified by crystal violet test and the absorbance was measured using microplate reader (OD570. The minimal inhibitory concentration (MIC and the minimal lethal concentration (MLC were determined and the results were confirmed by fluorescence microscopy. The significant difference in lead tolerance was observed between the mixed- and the single-species biofilms. The MIC of lead (Pb2+ for the examined biofilms (E. coli LM1, R. mucilaginosa and R. mucilaginosa / E. coli was recorded at concentrations of 4000 μg/ml, 4000 μg/ml and 16000 μg/ml, respectively. The MIC of mercury (Hg2+ for the biofilms was noticed at concentrations of 31.25 μg/ml, 250 μg/ml and 250 μg/ml, respectively. Standard antibiotics (amphotericin B and tetracycline were used as positive control. Results obtained for single-species biofilms were compared in between and with the results obtained for mixed-species biofilm. The tolerance of the mixed- species biofilm was higher in comparison to the singlespecies biofilms and the results were confirmed by a fluoresecence microscope. The obtained results suggest that the R. mucilaginosa / E. coli biofilm may have a potential to be used in bioremediation of wastewaters contaminated with lead and mercury.

A model for quasi parity-doublet spectra with strong coriolis mixing

International Nuclear Information System (INIS)

Minkov, N.; Drenska, S.; Strecker, M.

2013-01-01

The model of coherent quadrupole and octupole motion (CQOM) is combined with the reflection-asymmetric deformed shell model (DSM) in a way allowing fully microscopic description of the Coriolis decoupling and K-mixing effects in the quasi parity-doublet spectra of odd-mass nuclei. In this approach the even-even core is considered within the CQOM model, while the odd nucleon is described within DSM with pairing interaction. The Coriolis decoupling/mixing factors are calculated through a parity-projection of the single-particle wave function. Expressions for the Coriolis mixed quasi parity-doublet levels are obtained in the second order of perturbation theory, while the K-mixed core plus particle wave function is obtained in the first order. Expressions for the B(E1), B(E2) and B(E3) reduced probabilities for transitions within and between different quasi-doublets are obtained by using the total K-mixed wave function. The model scheme is elaborated in a form capable of describing the yrast and non-yrast quasi parity-doublet spectra in odd-mass nuclei. (author)

Modeling of particle mixing in the atmosphere

International Nuclear Information System (INIS)

Zhu, Shupeng

2015-01-01

assessment and mitigation) in January 2010 where the composition of individual particles was measured. One simulation assumes that particles are internally mixed, while the other explicitly models the mixing state with SCRAM. The simulation results of both bulk concentrations of chemical species and concentrations of individual particle classes are compared with the measurements. Then, the single particle diversity and the mixing-state index are computed using a quantification approach based on information theoretic entropy, and they are compared to those derived from the measurements at a urban site in Paris: the simulated mixing-state index is equal to 69% against 59% from the measurements, indicating that particles are not internally mixed over Paris. (author) [fr

Radioactivity reveals how crisps mix

Energy Technology Data Exchange (ETDEWEB)

Parker, David [School of Physics and Astronomy, University of Birmingham, Birmingham (United Kingdom)

2000-01-01

Many of the ''fluids'' processed in the food industry have strange flow properties that cannot easily be predicted. This is an important question in industry, since engineers need to know how such systems flow through pipes in production plants or how different components mix together. To counter this lack of knowledge, the fluids are generally processed for longer than necessary, which often proves expensive and may affect the quality of the final product. The University of Birmingham Positron Imaging Centre has developed a powerful technique to study the behaviour of crisps, yoghurt and ice cream - together with many other granular materials and viscous fluids - in a variety of industrial processes. In one case, the group labelled a single crisp using a positron-emitting radioisotope and added it to a rotating drum full of crisps. By tracking the movement of the labelled crisp, they could determine how uniformly the crisps were exposed to the flavouring that was added in the mixing process. In this article the author describes the research at the university's Positron Imaging Centre. (UK)

Radioactivity reveals how crisps mix

International Nuclear Information System (INIS)

Parker, David

2000-01-01

Many of the ''fluids'' processed in the food industry have strange flow properties that cannot easily be predicted. This is an important question in industry, since engineers need to know how such systems flow through pipes in production plants or how different components mix together. To counter this lack of knowledge, the fluids are generally processed for longer than necessary, which often proves expensive and may affect the quality of the final product. The University of Birmingham Positron Imaging Centre has developed a powerful technique to study the behaviour of crisps, yoghurt and ice cream - together with many other granular materials and viscous fluids - in a variety of industrial processes. In one case, the group labelled a single crisp using a positron-emitting radioisotope and added it to a rotating drum full of crisps. By tracking the movement of the labelled crisp, they could determine how uniformly the crisps were exposed to the flavouring that was added in the mixing process. In this article the author describes the research at the university's Positron Imaging Centre. (UK)

Bimaximal fermion mixing from the quark and leptonic mixing matrices

International Nuclear Information System (INIS)

Ohlsson, Tommy

2005-01-01

In this Letter, we show how the mixing angles of the standard parameterization add when multiplying the quark and leptonic mixing matrices, i.e., we derive explicit sum rules for the quark and leptonic mixing angles. In this connection, we also discuss other recently proposed sum rules for the mixing angles assuming bimaximal fermion mixing. In addition, we find that the present experimental and phenomenological data of the mixing angles naturally fulfill our sum rules, and thus, give rise to bilarge or bimaximal fermion mixing

Reactivity to sorbitan sesquioleate affects reactivity to fragrance mix I.

Science.gov (United States)

Geier, Johannes; Schnuch, Axel; Lessmann, Holger; Uter, Wolfgang

2015-11-01

Fragrance mix I (FM I) and its single constituents contain 5% and 1% sorbitan sesquioleate (SSO), respectively. SSO is a rare sensitizer and a potential irritant. To determine whether the outcome of the FM I breakdown test is affected by positive patch test reactivity to SSO. A retrospective analysis of data from the Information Network of Departments of Dermatology, 1998-2013, was performed. The full FM I breakdown test including SSO was tested in 2952 patients. Of these, 154 (5.2%) had a positive patch test reaction to SSO 20% pet. and 2709 (91.8%) had a negative patch test reaction. Positive reactions to one or more of the single fragrances contained in the mix were significantly more common (82.5% versus 57.3%) in SSO-positive patients, who also had more multiple reactions than FM I-positive patients with negative SSO reactions (61.5% versus 21.3% patients with reactions to two or more fragrances). Our results indicate that reactivity to SSO markedly affects the outcome of patch testing with FM I and its single constituents. SSO must be an obligatory part of the full FM I breakdown test, and should ideally be included in the baseline series. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

A new first-order turbulence mixing model for the stable atmospheric boundary-layer: development and testing in large-eddy and single column models

Science.gov (United States)

Huang, J.; Bou-Zeid, E.; Golaz, J.

2011-12-01

Parameterization of the stably-stratified atmospheric boundary-layer is of crucial importance to different aspects of numerical weather prediction at regional scales and climate modeling at global scales, such as land-surface temperature forecasts, fog and frost prediction, and polar climate. It is well-known that most operational climate models require excessive turbulence mixing of the stable boundary-layer to prevent decoupling of the atmospheric component from the land component under strong stability, but the performance of such a model is unlikely to be satisfactory under weakly and moderately stable conditions. In this study we develop and test a general turbulence mixing model of the stable boundary-layer which works under different stabilities and for steady as well as unsteady conditions. A-priori large-eddy simulation (LES) tests are presented to motivate and verify the new parameterization. Subsequently, an assessment of this model using the GFDL single-column model (SCM) is performed. Idealized test cases including continuously varying stability, as well as stability discontinuity, are used to test the new SCM against LES results. A good match of mean and flux profiles is found when the new parameterization is used, while other traditional first-order turbulence models using the concept of stability function perform poorly. SCM spatial resolution is also found to have little impact on the performance of the new turbulence closure, but temporal resolution is important and a numerical stability criterion based on the model time step is presented.

CFD simulations to study the effects of wall protrusions on microfluidic mixing

Science.gov (United States)

Sarkar, Sourav; Singh, K. K.; Shankar, V.; Shenoy, K. T.

2015-08-01

In this study the effects of different types of wall protrusions on microfluidic mixing are studied using computational fluid dynamics (CFD) simulations. Two new protrusions, single first bracket protrusions and double opposite first bracket protrusions (DOFBPs), are conceptualized, evaluated through CFD simulations and compared to protrusions having standard geometrical shapes, e.g. rectangular protrusions, triangular protrusions and semicircular protrusions. In the range of Reynolds numbers covered in this study, the microchannel having an opposed T-junction and DOFBPs is found to provide good mixing. A hybrid approach relying on the modification of microfluidic junctions as well as wall protrusions for enhancing microfluidic mixing is also evaluated. The microchannel based on the hybrid approach of an OA 10°-20°-165° WY-junction and DOFBPs is also found to provide very good mixing for a wide range of Reynolds numbers.

Temporally uncorrelated photon-pair generation by dual-pump four-wave mixing

DEFF Research Database (Denmark)

Christensen, Jesper Bjerge; McKinstrie, C. J.; Rottwitt, Karsten

2016-01-01

We study the preparation of heralded single-photon states using dual-pump spontaneous four-wave mixing. The dual-pump configuration, which in our case employs cross-polarized pumps, allows for a gradual variation of the nonlinear interaction strength enabled by a birefringence-induced walk...

Silver nanocrystal-decorated polyoxometalate single-walled nanotubes as nanoreactors for desulfurization catalysis at room temperature.

Science.gov (United States)

Zhang, Hao; Xu, Xiaobin; Lin, Haifeng; Ud Din, Muhammad Aizaz; Wang, Haiqing; Wang, Xun

2017-09-14

Ultrathin nanocrystals generally provide a remarkable catalytic performance due to their high specific surface area and exposure of certain active sites. However, deactivation caused by growth and gathering limits the catalytic application of ultrathin nanocrystals. Here we report Ag nanocrystal-decorated polyoxometalate (Ag-POM) single-walled nanotubes assembled via a concise, surfactant-free soaking method as a new kind of well-defined core-sheath nanoreactor. The diameter of Ag nanocrystals inside polyoxometalate nanotubes can be controlled via simply adjusting the reactant concentration. Ag-POM provided outstanding oxidative desulfurization (ODS) catalytic performance for aromatic sulfocompounds at room temperature. It was suggested that Ag nanocrystals decorated on the inner surface played a key role in adjusting the electronic distribution and enhancing the catalytic activity. The as-prepared Ag-POM nanotubes are promising candidate catalysts with enhanced performance for practical catalytic applications in the gasoline desulfurization industry.

Turbulence closure for mixing length theories

Science.gov (United States)

Jermyn, Adam S.; Lesaffre, Pierre; Tout, Christopher A.; Chitre, Shashikumar M.

2018-05-01

We present an approach to turbulence closure based on mixing length theory with three-dimensional fluctuations against a two-dimensional background. This model is intended to be rapidly computable for implementation in stellar evolution software and to capture a wide range of relevant phenomena with just a single free parameter, namely the mixing length. We incorporate magnetic, rotational, baroclinic, and buoyancy effects exactly within the formalism of linear growth theories with non-linear decay. We treat differential rotation effects perturbatively in the corotating frame using a novel controlled approximation, which matches the time evolution of the reference frame to arbitrary order. We then implement this model in an efficient open source code and discuss the resulting turbulent stresses and transport coefficients. We demonstrate that this model exhibits convective, baroclinic, and shear instabilities as well as the magnetorotational instability. It also exhibits non-linear saturation behaviour, and we use this to extract the asymptotic scaling of various transport coefficients in physically interesting limits.

Simulating double-peak hydrographs from single storms over mixed-use watersheds

Science.gov (United States)

Yang Yang; Theodore A. Endreny; David J. Nowak

2015-01-01

Two-peak hydrographs after a single rain event are observed in watersheds and storms with distinct volumes contributing as fast and slow runoff. The authors developed a hydrograph model able to quantify these separate runoff volumes to help in estimation of runoff processes and residence times used by watershed managers. The model uses parallel application of two...

Mixed oxide fuel pellet and manufacturing method thereof

International Nuclear Information System (INIS)

Yuda, Ryoichi; Ito, Ken-ichi; Masuda, Hiroshi.

1993-01-01

In a method of manufacturing nuclear fuel pellets which comprises compression molding a mixed oxide powder containing UO 2 and PuO 2 followed by sintering, a sintering agent having a composition comprising about 40 to 80 wt% of SiO 2 and the balance of Al 2 O 3 is mixed to a mixed oxide at a ratio of about 40ppm to about 0.5 wt% based on the total amount of the mixed oxide and the sintering agent, to prepare a mixture. The mixture is molded into a compression product and then sintered at a weakly acidic atmosphere at a temperature of about 1500degC to 1800degC. With such procedures, the sintering agent forms an eutectic product of a single liquid phase, PuO 2 is dispersed over the entire region of the pellet by way of the liquid phase, formation of a solid solution phase is promoted to annihilate a free PuO 2 phase. Further, growth of crystal grains is promoted. Accordingly, since the MOX fuel pellets prepared according to the present invention have a uniform solid solution state, and no free PuO 2 phase remains, increase of FP gas emission due to local nuclear fission of Pu can be avoided. (T.M.)

Single crystal growth and structure refinements of CsMxTe2-xO6 (M = Al, Ga, Ge, In) pyrochlores

International Nuclear Information System (INIS)

Siritanon, Theeranun; Sleight, A.W.; Subramanian, M.A.

2011-01-01

Graphical abstract: Single crystals of CsM x Te 2-x O 6 pyrochlores with M = Al, Ga, Ge, and In have been grown and structure refinements indicate deviations from ideal stoichiometry presumably related to mixed valency of tellurium. Highlights: → Single crystals of CsM x Te 2-x O 6 pyrochlores with M = Al, Ga, Ge, and In have been grown. → Structure refinements from single crystal X-ray diffraction data confirm e structure. → Deviations from ideal stoichiometry suggest mixed valency of tellurium and hence conductivity. -- Abstract: Single crystals of CsM x Te 2-x O 6 pyrochlores with M = Al, Ga, Ge, and In have been grown from a TeO 2 flux. Structure refinements from single crystal X-ray diffraction data are reported. These results are used to discuss deviations from ideal stoichiometry that result in electronic conductivity presumably related to mixed valency of tellurium.

Elucidation of reactive wavepackets by two-dimensional resonance Raman spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Guo, Zhenkun; Molesky, Brian P.; Cheshire, Thomas P.; Moran, Andrew M., E-mail: ammoran@email.unc.edu [Department of Chemistry, University of North Carolina at Chapel Hill, Chapel Hill, North Carolina 27599 (United States)

2015-09-28

Traditional second-order kinetic theories fail to describe sub-picosecond photochemical reactions when solvation and vibrational dephasing undermine the assumption of equilibrium initial conditions. Four-wave mixing spectroscopies may reveal insights into such non-equilibrium processes but are limited by the single “population time” available in these types of experiments. Here, we use two-dimensional resonance Raman (2DRR) spectroscopy to expose correlations between coherent nuclear motions of the reactant and product in the photodissociation reaction of triiodide. It is shown that the transition of a nuclear wavepacket from the reactant (triiodide) to product (diiodide) states gives rise to a unique pattern of 2DRR resonances. Peaks associated with this coherent reaction mechanism are readily assigned, because they are isolated in particular quadrants of the 2DRR spectrum. A theoretical model in which the chemical reaction is treated as a vibronic coherence transfer transition from triiodide to diiodide reproduces the patterns of 2DRR resonances detected in experiments. These signal components reveal correlation between the nonequilibrium geometry of triiodide and the vibrational coherence frequency of diiodide. The 2DRR signatures of coherent reaction mechanisms established in this work may generalize to studies of ultrafast energy and charge transfer processes.

Study on effect of mixing mechanism by the transverse gaseous injection flow in scramjet engine with variable parameters

Science.gov (United States)

Yadav, Siddhita; Pandey, K. M.

2018-04-01

In scramjet engine the mixing mechanism of fuel and atmospheric air is very complicated, because the fuel have time in milliseconds for mixing with atmospheric air in combustion chamber having supersonic speed. Mixing efficiency of fuel and atmospheric air depends on mainly these parameters: Aspect ratio of injector, vibration amplitude, shock type, number of injector, jet to transverse flow momentum flux ratio, injector geometry, injection angle, molecular weight, incoming air stream angle, jet to transverse flow pressure ratio, spacing variation, mass flow rate of fuel etc. here is a very brief study of these parameters from previously done research on these parameters for the improvement of mixing efficiency. The mixing process have the significant role for the working of engine, and mixing between the atmospheric air and the jet fuel is significant factor for improving the overall thrust of the engine. The results obtained by study of papers are obtained by the 3D-Reynolds Average-Nervier-Stokes(RANS) equations along with the 2-equation k-ω shear-stress-transport (SST) turbulence model. Engine having multi air jets have 60% more mixing efficiency than single air jet, thus if the jets are increased, the mixing efficiency of engine can also be increased up to 150% by changing jet from 1 to 16. When using delta shape of injector the mixing efficiency is inversely proportional to the pressure ratio. When the fuel is injected inside the combustor from the top and bottom walls of the engine efficiency of mixing in reacting zone is higher than the single wall injection and in comparison to parallel flow, the transverse type flow is better as the atmospheric air jet can penetrate smoothly in the fuel jets and mixes well in less time. Hence this study of parameters and their effects on mixing can enhance the efficiency of mixing in engine.

Traffic simulation for mixed traffic systems | Mbam | Global Journal of ...

African Journals Online (AJOL)

Traffic problem is classified into single and mixed, especially in most developing countries, where motorbikes are used as the most popular transportation system. The aim of this paper is to introduce the motorbike symbol into the traffic light control system to separate cars/lorries indicator from that of motorbike. This is likely ...

Mixed gated/exhaustive service in a polling model with priorities

NARCIS (Netherlands)

Boon, M.A.A.; Adan, I.J.B.F.

2008-01-01

In this paper we consider a single-server polling system with switch-over times. We introduce a new service discipline, mixed gated/exhaustive service, that can be used for queues with two types of customers: high and low priority customers. At the beginning of a visit of the server to such a queue,

European mixed forests

DEFF Research Database (Denmark)

Bravo-Oviedo, Andres; Pretzsch, Hans; Ammer, Christian

2014-01-01

Aim of study: We aim at (i) developing a reference definition of mixed forests in order to harmonize comparative research in mixed forests and (ii) review the research perspectives in mixed forests. Area of study: The definition is developed in Europe but can be tested worldwide. Material...... and Methods: Review of existent definitions of mixed forests based and literature review encompassing dynamics, management and economic valuation of mixed forests. Main results: A mixed forest is defined as a forest unit, excluding linear formations, where at least two tree species coexist at any...... density in mixed forests, (iii) conversion of monocultures to mixed-species forest and (iv) economic valuation of ecosystem services provided by mixed forests. Research highlights: The definition is considered a high-level one which encompasses previous attempts to define mixed forests. Current fields...

A comparison of patient-centered and case-mix reimbursement for nursing home care.

Science.gov (United States)

Willemain, T R

1980-01-01

The trend in payment for nursing home services has been toward making finer distinctions amont patients and the rates at which their care is reimbursed. The ultimate in differentiation is patient-centered reimbursement, whereas each patient's rate is individually determined. This paper introduces a model of overpayment and under-payment for comparing the potential performance of alternative reimbursement schemes. The model is used in comparing the patient-centered approach with case-mix reimbursement, which assigns a single rate to all patients in a nursing home on the basis of the facility's case mix. Roughly speaking, the case-mix approach is preferable whenever the differences between patient's needs are smaller than the errors in needs assessment. Since this condition appears to hold in practice today, case-mix reimbursement seems preferable for the short term.

Mixed Lactobacillus plantarum Strains Inhibit Staphylococcus aureus Induced Inflammation and Ameliorate Intestinal Microflora in Mice.

Science.gov (United States)

Ren, Dayong; Gong, Shengjie; Shu, Jingyan; Zhu, Jianwei; Rong, Fengjun; Zhang, Zhenye; Wang, Di; Gao, Liangfeng; Qu, Tianming; Liu, Hongyan; Chen, Ping

2017-01-01

Objective . Staphylococcus aureus is an important pathogen that causes intestinal infection. We examined the immunomodulatory function of single and mixed Lactobacillus plantarum strains, as well as their impacts on the structure of the microbiome in mice infected with Staphylococcus aureus . The experiment was divided into three groups: protection, treatment, and control. Serum IFN- γ and IL-4 levels, as well as intestinal sIgA levels, were measured during and 1 week after infection with Staphylococcus aureus with and without Lactobacillus plantarum treatment. We used 16s rRNA tagged sequencing to analyze microbiome composition. IFN- γ /IL-4 ratio decreased significantly from infection to convalescence, especially in the mixed Lactobacillus plantarum group. In the mixed Lactobacillus plantarum group the secretion of sIgA in the intestine of mice (9.4-9.7 ug/mL) was significantly higher than in the single lactic acid bacteria group. The dominant phyla in mice are Firmicutes , Bacteroidetes , and Proteobacteria . Treatment with mixed lactic acid bacteria increased the anti-inflammatory factor and the secretion of sIgA in the intestine of mice infected with Staphylococcus aureus and inhibited inflammation.

Soluplus/TPGS mixed micelles for dioscin delivery in cancer therapy.

Science.gov (United States)

Zhao, Jing; Xu, Youwei; Wang, Changyuan; Ding, Yanfang; Chen, Manyu; Wang, Yifei; Peng, Jinyong; Li, Lei; Lv, Li

2017-07-01

Dioscin has shown cytotoxicity against cancer cells, but its poor solubility and stability have limited its clinical application. In this study, we designed mixed micelles composed of TPGS and Soluplus ® copolymers entrapping the poorly soluble anticancer drug dioscin. In order to improve the aqueous solubility and bioactivity of dioscin, TPGS/Soluplus ® mixed micelles with an optimal ratio were prepared using a thin-film hydration method, and their physicochemical properties were characterized. Cellular cytotoxicity and uptake of the dioscin-loaded TPGS/Soluplus ® mixed micelles were studied in MCF-7 breast cancer cells and A2780s ovarian cancer cells. The pharmacokinetics of free dioscin and dioscin-loaded TPGS/Soluplus ® mixed micelles was studied in vivo in male Sprague-Dawley rats via a single intravenous injection in the tail vein. The average size of the optimized mixed micelle was 67.15 nm, with 92.59% drug encapsulation efficiency and 4.63% drug loading efficiency. The in vitro release profile showed that the mixed micelles presented sustained release behavior compared to the anhydrous ethanol solution of dioscin. In vitro cytotoxicity assays were conducted on human cancer cell lines including A2780s ovarian cancer cells and MCF-7 breast cancer cells. The mixed micelles exhibited better antitumor activity compared to free dioscin against all cell lines, which may benefit from the significant increase in the cellular uptake of dioscin from mixed micelles compared to free dioscin. The pharmacokinetic study showed that the mixed micelle formulation achieved a 1.3 times longer mean residual time (MRT) in circulation and a 2.16 times larger area under the plasma concentration-time curve (AUC) than the free dioscin solution. Our results suggest that the dioscin-loaded mixed micelles developed in this study might be a potential nano drug-delivery system for cancer chemotherapy.

Performance evaluation of rotating pump jet mixing of radioactive wastes in Hanford Tanks 241-AP-102 and -104

International Nuclear Information System (INIS)

Onishi, Y.; Recknagle, K.P.

1998-07-01

The purpose of this study was to confirm the adequacy of a single mixer pump to fully mix the wastes that will be stored in Tanks 241-AP-102 and -104. These Hanford double-shell tanks (DSTs) will be used as staging tanks to receive low-activity wastes from other Hanford storage tanks and, in turn, will supply the wastes to private waste vitrification facilities for eventual solidification. The TEMPEST computer code was applied to Tanks AP-102 and -104 to simulate waste mixing generated by the 60-ft/s rotating jets and to determine the effectiveness of the single rotating pump to mix the waste. TEMPEST simulates flow and mass/heat transport and chemical reactions (equilibrium and kinetic reactions) coupled together. Section 2 describes the pump jet mixing conditions the authors evaluated, the modeling cases, and their parameters. Section 3 reports model applications and assessment results. The summary and conclusions are presented in Section 4, and cited references are listed in Section 5

Impact of mixed modes on measurement errors and estimates of change in panel data

Directory of Open Access Journals (Sweden)

Alexandru Cernat

2015-07-01

Full Text Available Mixed mode designs are receiving increased interest as a possible solution for saving costs in panel surveys, although the lasting effects on data quality are unknown. To better understand the effects of mixed mode designs on panel data we will examine its impact on random and systematic error and on estimates of change. The SF12, a health scale, in the Understanding Society Innovation Panel is used for the analysis. Results indicate that only one variable out of 12 has systematic differences due to the mixed mode design. Also, four of the 12 items overestimate variance of change in time in the mixed mode design. We conclude that using a mixed mode approach leads to minor measurement differences but it can result in the overestimation of individual change compared to a single mode design.

Utilization of the heat of mixing in open-circuit throttle refrigerators

International Nuclear Information System (INIS)

Zhakharov, N.D.; Anikeev, G.N.; Grezin, A.K.

1986-01-01

Open-circuit throttle refrigerators based on gas mixtures operate, as a rule, according to a single-stream scheme. The refrigerating effect is determined by the isothermal throttling effect of the mixture in the cylinder under the conditions at the inlet to the cryogenic unit. The authors use the heat of mixing of the cryogenic mixtures to increase the available refrigerating effect. Data are presented on mixtures of nitrogen and Freon-13; the thermodynamic properties of these compounds have been investigated experimentally over a wide range of parameters. It was found that in the case of correct selection of the scheme and complex optimization of the parameters, two-stream throttle refrigerators exceed the single-stream throttle refrigerators by at least a factor of 1.5 with respect to relative useful energy. With account taken of the design, technological, and operational parameters, that which is most promising is the scheme with mixing of the components in reverse flow

Experimental detection of nonclassical correlations in mixed-state quantum computation

International Nuclear Information System (INIS)

Passante, G.; Moussa, O.; Trottier, D. A.; Laflamme, R.

2011-01-01

We report on an experiment to detect nonclassical correlations in a highly mixed state. The correlations are characterized by the quantum discord and are observed using four qubits in a liquid-state nuclear magnetic resonance quantum information processor. The state analyzed is the output of a DQC1 computation, whose input is a single quantum bit accompanied by n maximally mixed qubits. This model of computation outperforms the best known classical algorithms and, although it contains vanishing entanglement, it is known to have quantum correlations characterized by the quantum discord. This experiment detects nonvanishing quantum discord, ensuring the existence of nonclassical correlations as measured by the quantum discord.

A study of the mixing state of black carbon in urban zone

Science.gov (United States)

Mallet, M.; Roger, J. C.; Despiau, S.; Putaud, J. P.; Dubovik, O.

2004-02-01

The knowledge of the mixing state of black carbon particle with other aerosol species is critical for adequate simulations of the direct radiative effect of black carbon particles and its effect on climate. This paper reports the investigation of the mixing state of black carbon aerosol in the urban zone. The study uses a combination of in situ and ground-based remote sensing observations conducted during the ESCOMPTE experiment, which took place in industrialized region in France in summer of 2001. The criteria we used for identifying mixing state relies on the known enhancement of absorption for aerosol composed by internal versus external mixtures of black carbon with weakly absorbing aerosol components. First, using in situ aerosol data, we performed Mie computations and reconstructed the single scattering albedo of aerosol for the two different mixing assumptions: black carbon mixed externally or internally with other aerosol species. Then, we compared the obtained values ωo,int and ωo,ext with the retrievals of ωo from independent AERONET Sun-photometric measurements. The aerosol single scattering albedo (ωo,aer.) derived from the AERONET photometer observations (with the mean value equal to 0.84 ± 0.04) was found to be close to ωo,ext reconstructed from in situ observation under assumptions of external mixture. This similarity between AERONET values and external mixture simulations was observed during all the days studied. Our conclusion on external mixture of black carbon aerosol with other particles in urban zone during ESCOMPTE (close to the pollution source) is coherent with observations made during other independent studies reported in a number of recent publications.

Mobile Mixed Reality for Experiential Learning and Simulation in Medical and Health Sciences Education

Directory of Open Access Journals (Sweden)

James Birt

2018-01-01

Full Text Available New accessible learning methods delivered through mobile mixed reality are becoming possible in education, shifting pedagogy from the use of two dimensional images and videos to facilitating learning via interactive mobile environments. This is especially important in medical and health education, where the required knowledge acquisition is typically much more experiential, self-directed, and hands-on than in many other disciplines. Presented are insights obtained from the implementation and testing of two mobile mixed reality interventions across two Australian higher education classrooms in medicine and health sciences, concentrating on student perceptions of mobile mixed reality for learning physiology and anatomy in a face-to-face medical and health science classroom and skills acquisition in airways management focusing on direct laryngoscopy with foreign body removal in a distance paramedic science classroom. This is unique because most studies focus on a single discipline, focusing on either skills or the learner experience and a single delivery modality rather than linking cross-discipline knowledge acquisition and the development of a student’s tangible skills across multimodal classrooms. Outcomes are presented from post-intervention student interviews and discipline academic observation, which highlight improvements in learner motivation and skills, but also demonstrated pedagogical challenges to overcome with mobile mixed reality learning.

EFFECTS OF ROTATIONALLY INDUCED MIXING IN COMPACT BINARY SYSTEMS WITH LOW-MASS SECONDARIES AND IN SINGLE SOLAR-TYPE STARS

International Nuclear Information System (INIS)

Chatzopoulos, E.; Robinson, Edward L.; Wheeler, J. Craig

2012-01-01

Many population synthesis and stellar evolution studies have addressed the evolution of close binary systems in which the primary is a compact remnant and the secondary is filling its Roche lobe, thus triggering mass transfer. Although tidal locking is expected in such systems, most studies have neglected the rotationally induced mixing that may occur. Here we study the possible effects of mixing in mass-losing stars for a range of secondary star masses and metallicities. We find that tidal locking can induce rotational mixing prior to contact and thus affect the evolution of the secondary star if the effects of the Spruit-Tayler dynamo are included both for angular momentum and chemical transport. Once contact is made, the effect of mass transfer tends to be more rapid than the evolutionary timescale, so the effects of mixing are no longer directly important, but the mass-transfer strips matter to inner layers that may have been affected by the mixing. These effects are enhanced for secondaries of 1-1.2 M ☉ and for lower metallicities. We discuss the possible implications for the paucity of carbon in the secondaries of the cataclysmic variable SS Cyg and the black hole candidate XTE J1118+480 and for the progenitor evolution of Type Ia supernovae. We also address the issue of the origin of blue straggler stars in globular and open clusters. We find that for models that include rotation consistent with that observed for some blue straggler stars, evolution is chemically homogeneous. This leads to tracks in the H-R diagram that are brighter and bluer than the non-rotating main-sequence turn-off point. Rotational mixing could thus be one of the factors that contribute to the formation of blue stragglers.

Effect of aluminum and silicon reactants and process parameters on glass-ceramic waste form characteristics for immobilization of high-level fluorinel-sodium calcined waste

International Nuclear Information System (INIS)

Vinjamuri, K.

1993-06-01

In this report, the effects of aluminum and silicon reactants, process soak time and the initial calcine particle size on glass-ceramic waste form characteristics for immobilization of the high-level fluorinel-sodium calcined waste stored at the Idaho Chemical Processing Plant (ICPP) are investigated. The waste form characteristics include density, total and normalized elemental leach rates, and microstructure. Glass-ceramic waste forms were prepared by hot isostatically pressing (HIPing) a pre-compacted mixture of pilot plant fluorinel-sodium calcine, Al, and Si metal powders at 1050 degrees C, 20,000 psi for 4 hours. One of the formulations with 2 wt % Al was HIPed for 4, 8, 16 and 24 hours at the same temperature and pressure. The calcine particle size range include as calcined particle size smaller than 600 μm (finer than -30 mesh, or 215 μm Mass Median Diameter, MMD) and 180 μm (finer than 80 mesh, or 49 μm MMD)

Multiple Estimation Architecture in Discrete-Time Adaptive Mixing Control

Directory of Open Access Journals (Sweden)

Simone Baldi

2013-05-01

Full Text Available Adaptive mixing control (AMC is a recently developed control scheme for uncertain plants, where the control action coming from a bank of precomputed controller is mixed based on the parameter estimates generated by an on-line parameter estimator. Even if the stability of the control scheme, also in the presence of modeling errors and disturbances, has been shown analytically, its transient performance might be sensitive to the initial conditions of the parameter estimator. In particular, for some initial conditions, transient oscillations may not be acceptable in practical applications. In order to account for such a possible phenomenon and to improve the learning capability of the adaptive scheme, in this paper a new mixing architecture is developed, involving the use of parallel parameter estimators, or multi-estimators, each one working on a small subset of the uncertainty set. A supervisory logic, using performance signals based on the past and present estimation error, selects the parameter estimate to determine the mixing of the controllers. The stability and robustness properties of the resulting approach, referred to as multi-estimator adaptive mixing control (Multi-AMC, are analytically established. Besides, extensive simulations demonstrate that the scheme improves the transient performance of the original AMC with a single estimator. The control scheme and the analysis are carried out in a discrete-time framework, for easier implementation of the method in digital control.

Mixed frequency excitation of an electrostatically actuated resonator

KAUST Repository

Ramini, Abdallah

2015-04-24

We investigate experimentally and theoretically the dynamics of a capacitive resonator under mixed frequency excitation of two AC harmonic signals. The resonator is composed of a proof mass suspended by two cantilever beams. Experimental measurements are conducted using a laser Doppler vibrometer to reveal the interesting dynamics of the system when subjected to two-source excitation. A nonlinear single-degree-of-freedom model is used for the theoretical investigation. The results reveal combination resonances of additive and subtractive type, which are shown to be promising to increase the bandwidth of the resonator near primary resonance frequency. Our results also demonstrate the ability to shift the combination resonances to much lower or much higher frequency ranges. We also demonstrate the dynamic pull-in instability under mixed frequency excitation. © 2015 Springer-Verlag Berlin Heidelberg

Mixing enhancement in a scramjet combustor using fuel jet injection swirl

Science.gov (United States)

Flesberg, Sonja M.

The scramjet engine has proven to be a viable means of powering a hypersonic vehicle, especially after successful flights of the X-51 WaveRider and various Hy-SHOT test vehicles. The major challenge associated with operating a scramjet engine is the short residence time of the fuel and oxidizer in the combustor. The fuel and oxidizer have only milliseconds to mix, ignite and combust in the combustion chamber. Combustion cannot occur until the fuel and oxidizer are mixed on a molecular level. Therefore the improvement of mixing is of utmost interest since this can increase combustion efficiency. This study investigated mixing enhancement of fuel and oxidizer within the combustion chamber of a scramjet by introducing swirl to the fuel jet. The investigation was accomplished with numerical simulations using STAR-CCM+ computational fluid dynamic software. The geometry of the University of Virginia Supersonic Combustion Facility was used to model the isolator, combustor and nozzle of a scramjet engine for simulation purposes. Experimental data from previous research at the facility was used to verify the simulation model before investigating the effect of fuel jet swirl on mixing. The model used coaxial fuel jet with a swirling annular jet. Single coaxial fuel jet and dual coaxial fuel jet configurations were simulated for the investigation. The coaxial fuel jets were modelled with a swirling annular jet and non-swirling core jet. Numerical analysis showed that fuel jet swirl not only increased mixing and entrainment of the fuel with the oxidizer but the mixing occurred further upstream than without fuel jet swirl. The burning efficiency was calculated for the all the configurations. An increase in burning efficiency indicated an increase in the mixing of H2 with O2. In the case of the single fuel jet models, the maximum burning efficiency increase due to fuel injection jet swirl was 23.3%. The research also investigated the possibility that interaction between two

Simulation of Turbulent Wake at Mixing of Two Confined Horizontal Flows

Directory of Open Access Journals (Sweden)

Rok Krpan

2018-01-01

Full Text Available The development of a turbulent mixing layer at mixing of two horizontal water streams with slightly different densities is studied by the means of numerical simulation. The mixing of such flows can be modelled as the flow of two components, where the concentration of one component in the mixing region is described as a passive scalar. The velocity field remains common over the entire computational domain, where the density and viscosity difference due to the concentration mainly affects the turbulent fluctuations in the mixing region. The numerical simulations are performed with the open source code OpenFOAM using two different approaches for turbulence modelling, Reynolds Averaged Navier Stokes equations (RANS and Large Eddy Simulation (LES. The simulation results are discussed and compared with the benchmark experiment obtained within the frame of OECD/NEA benchmark test. A good agreement with experimental results is obtained in the case of the single liquid experiment. A high discrepancy between the simulated and the experimental velocity fluctuations in the case of mixing of the flows with the slightly different densities and viscosities triggered a systematic investigation of the modelling approaches that helped us to find out and interpret the main reasons for the disagreement.

Effects of Pretreatment of Single and Mixed Lignocellulosic Substrates on Production of Endoglucanase by Bacillus aerius S5.2

Directory of Open Access Journals (Sweden)

Mushafau Adebayo Oke

2016-06-01

Full Text Available A mixed substrate (MS comprising oil palm empty fruit bunch (EFB, oil palm frond (OPF, and rice husk (RH was evaluated for endoglucanase production by Bacillus aerius S5.2. Effects of sulphuric acid, sodium hydroxide, N-methylmorpholine-N-oxide (NMMO, and hydrothermal pretreatments on endoglucanase production were investigated. Endoglucanase production by B. aerius on the untreated (0.677 U/mL and pretreated MS (0.305 – 0.630 U/mL was generally similar, except that the acid (0.305 U/mL and hydrothermal (0.549 U/mL pretreatments that were more severe consequently produced significantly lower titres. Alkali pretreatment supported the highest enzyme production (0.630 U/mL among all pretreatments that were studied. When endoglucanase production on the alkali-pretreated MS and single substrates (SS was compared, alkali-pretreated EFB produced a titre (0.655 U/mL similar to the MS, and this was significantly higher than titres recorded on OPF (0.504 U/mL and RH (0.525 U/mL. Lower enzyme production was found to be consistent with higher pretreatment severity and greater removal of amorphous regions in all the pretreatments. Furthermore, combining the SS showed no adverse effects on endoglucanase production.

Mixing Phenomena in a Bottom Blown Copper Smelter: A Water Model Study

Science.gov (United States)

Shui, Lang; Cui, Zhixiang; Ma, Xiaodong; Akbar Rhamdhani, M.; Nguyen, Anh; Zhao, Baojun

2015-03-01

The first commercial bottom blown oxygen copper smelting furnace has been installed and operated at Dongying Fangyuan Nonferrous Metals since 2008. Significant advantages have been demonstrated in this technology mainly due to its bottom blown oxygen-enriched gas. In this study, a scaled-down 1:12 model was set up to simulate the flow behavior for understanding the mixing phenomena in the furnace. A single lance was used in the present study for gas blowing to establish a reliable research technique and quantitative characterisation of the mixing behavior. Operating parameters such as horizontal distance from the blowing lance, detector depth, bath height, and gas flow rate were adjusted to investigate the mixing time under different conditions. It was found that when the horizontal distance between the lance and detector is within an effective stirring range, the mixing time decreases slightly with increasing the horizontal distance. Outside this range, the mixing time was found to increase with increasing the horizontal distance and it is more significant on the surface. The mixing time always decreases with increasing gas flow rate and bath height. An empirical relationship of mixing time as functions of gas flow rate and bath height has been established first time for the horizontal bottom blowing furnace.

Mixing and mass transfer in a pilot scale U-loop bioreactor

DEFF Research Database (Denmark)

Petersen, Leander Adrian Haaning; Villadsen, John; Jørgensen, Sten Bay

2017-01-01

A system capable of handling a large volumetric gas fraction while providing a high gas to liquid mass transfer is a necessity if the metanotrophic bacterium Methylococcus capsulatus is to be used in single cell protein (SCP) production. In this study mixing time and mass transfer coefficients we...

Laser‐Self‐Mixing Interferometry for Mechatronics Applications

Directory of Open Access Journals (Sweden)

Gaetano Scamarcio

2009-05-01

Full Text Available We report on the development of an all-interferometric optomechatronic sensor for the detection of multi-degrees-of-freedom displacements of a remote target. The prototype system exploits the self-mixing technique and consists only of a laser head, equipped with six laser sources, and a suitably designed reflective target. The feasibility of the system was validated experimentally for both single or multi-degrees-of-freedom measurements, thus demonstrating a simple and inexpensive alternative to costly and bulky existing systems.

Laser-self-mixing interferometry for mechatronics applications.

Science.gov (United States)

Ottonelli, Simona; Dabbicco, Maurizio; De Lucia, Francesco; di Vietro, Michela; Scamarcio, Gaetano

2009-01-01

We report on the development of an all-interferometric optomechatronic sensor for the detection of multi-degrees-of-freedom displacements of a remote target. The prototype system exploits the self-mixing technique and consists only of a laser head, equipped with six laser sources, and a suitably designed reflective target. The feasibility of the system was validated experimentally for both single or multi-degrees-of-freedom measurements, thus demonstrating a simple and inexpensive alternative to costly and bulky existing systems.

Mixing it but not mixed-up: mixed methods research in medical education (a critical narrative review).

Science.gov (United States)

Maudsley, Gillian

2011-01-01

Some important research questions in medical education and health services research need 'mixed methods research' (particularly synthesizing quantitative and qualitative findings). The approach is not new, but should be more explicitly reported. The broad search question here, of a disjointed literature, was thus: What is mixed methods research - how should it relate to medical education research?, focused on explicit acknowledgement of 'mixing'. Literature searching focused on Web of Knowledge supplemented by other databases across disciplines. Five main messages emerged: - Thinking quantitative and qualitative, not quantitative versus qualitative - Appreciating that mixed methods research blends different knowledge claims, enquiry strategies, and methods - Using a 'horses for courses' [whatever works] approach to the question, and clarifying the mix - Appreciating how medical education research competes with the 'evidence-based' movement, health services research, and the 'RCT' - Being more explicit about the role of mixed methods in medical education research, and the required expertise Mixed methods research is valuable, yet the literature relevant to medical education is fragmented and poorly indexed. The required time, effort, expertise, and techniques deserve better recognition. More write-ups should explicitly discuss the 'mixing' (particularly of findings), rather than report separate components.

From UV/IR mixing to closed strings

International Nuclear Information System (INIS)

Lopez, Esperanza

2003-01-01

It was shown in [1] that the leading UV/IR mixing effects in noncommutative gauge theories on D-branes are able to capture information about the closed string spectrum of the parent string theory. The analysis was carried out for D-branes on nonsupersymmetric C 3 /Z N orbifolds of Type IIB. In this paper we consider D-branes on twisted circles compactifications of Type II string theory. We find that the signs of the leading UV/IR mixing effects know about the (mass) 2 gap between the lowest modes in NSNS and RR closed string towers. Moreover, the relevant piece of the field theory effective action can be reproduced purely in the language of closed strings. Remarkably, this approach unifies in a single structure, that of a closed string exchange between D-branes, both the leading planar and nonplanar effects associated to the absence of supersymmetry. (author)

Mixing and solid suspension of up-down agitators in a slab tank

International Nuclear Information System (INIS)

Ramsey, C.J.

1989-01-01

Seven different up-down agitators were studied for their ability to produce mixing and solid suspension in a slab tank. Mixing times were measured as the time needed to disperse injected dye. The solid suspension studies determined the minimum stroke frequency of the agitators needed for complete off-bottom suspension. The effects of stroke frequency, n; amplitude, a; blade width, w; blade clearance, c; and liquid depth, h, and weight percent solids, X, were studied. The most effective geometry, in terms of mixing, solid suspension and design simplicity, was a single flat blade with minimum off-bottom clearance and a blade width/tank thickness ratio, w/T, of 0.74 at the maximum stroke amplitude studied. 15 refs., 7 figs

Broadband Shock Noise in Internally-Mixed Dual-Stream Jets

Science.gov (United States)

Bridges, James E.

2009-01-01

Broadband shock noise (BBSN) has been studied in some detail in single-flow jets and recently in dual-stream jets with separate flow exhaust systems. Shock noise is of great concern in these latter cases because of the noise created for the aircraft cabin by the underexpanded nozzle flow at cruise. Another case where shock noise is of concern is in the case of future supersonic aircraft that are expected to have bypass ratios small enough to justify internally mixed exhaust systems, and whose mission will push cycles to the point of imperfectly expanded flows. Dual-stream jets with internally mixed plume have some simplifying aspects relative to the separate flow jets, having a single shock structure given by the common nozzle pressure. This is used to separate the contribution of the turbulent shear layer to the broadband shock noise. Shock structure is held constant while the geometry and strength of the inner and merged shear layers are varying by changing splitter area ratio and core stream temperature. Flow and noise measurements are presented which document the efforts at separating the contribution of the inner shear layer to the broadband shock noise.

A mathematical model for turbulent incompressible flows through mixing grids

International Nuclear Information System (INIS)

Allaire, G.

1989-01-01

A mathematical model is proposed for the computation of turbulent incompressible flows through mixing grids. This model is obtained as follows: in a three-dimentional-domain we represent a mixing grid by small identical wings of size ε 2 periodically distributed at the nodes of a plane regular mesh of size ε, and we consider incompressible Navier-Stokes equations with a no-slip condition on the wings. Using an appropriate homogenization process we pass to the limit when ε tends to zero and we obtain a Brinkman equation, i.e. a Navier-Stokes equation plus a zero-order term for the velocity, in a homogeneous domain without anymore wings. The interest of this model is that the spatial discretization is simpler in a homogeneous domain, and, moreover, the new term, which expresses the grid's mixing effect, can be evaluated with a local computation around a single wing

Growth and study of barium oxalate single crystals in agar gel

Indian Academy of Sciences (India)

Barium oxalate was grown in agar gel at ambient temperature. The effect of various parameters like gel concentration, gel setting time and concentration of the reactants on the growth of these crystals was studied. Prismatic platy shaped spherulites and dendrites were obtained. The grown crystals were characterized by ...

Yield of single-strand breaks in the DNA of E. coli 10 msec after irradiation

Energy Technology Data Exchange (ETDEWEB)

Fox, R A; Fielden, E M; Sapora, O [Institute of Cancer Research, Sutton (UK). Surrey Branch

1976-04-01

The rapid mixing of 0.3M alkali with a suspension of E.coli B/r 6 +- 3 and 144 +- 3 msec after irradiation with electrons (4.3 MeV, 0 to 50 krad) has been used to make a comparison of the yields of single strand breaks in the presence and absence of oxygen. No significant difference was observed between the numbers of single strand breaks appearing at 6 and 144 msec after irradiation. Assuming that mixing with alkali inactivates the cellular repair enzymes within several milliseconds, these results indicate that enzymic repair does not operate within this time scale. It seems probable that radiation chemical processes are responsible for the initial oxygen effect on single strand breaks.

Study on HCl Driving Force for the Reaction of NaCl-Maleic Acid Mixing Single Droplet Using Micro-FTIR Spectroscopy

Science.gov (United States)

He, Xiang; Zhang, Yunhong

2016-04-01

Chemical aging is the one of the most important physicochemical process in atmospheric aerosols. Mixing of sea salt and water-soluble organic components has profound effects on the volatile characteristic and evolving chemical composition of the anthropogenic origin aerosols, which are poorly understood. In this study, the chemical reaction behavior of the mixture of NaCl and maleic acid (H2MA) micron-level single droplet was investigated using a gas-flow system combined with microscopic Fourier transform infrared (micro-FTIR) spectrometer over the range of relative humidity (63˜95% RH) for the first time. The results showed that the mixture of NaCl and H2MA single droplet could react to form monosodium maleate salt (NaHMA) at the constant RH from the characterization of the FTIR. The reaction is a result of an acid displacement reaction R1, which is driven by high volatility of the HCl product. NaCl(aq)+H2MA(aq)=NaHMA(aq)+HCl(aq,g) (R1) According to the change tendency of the absorbance values of 1579 cm-1 COO- stretching band of the NaHMA dependent upon reaction times at different RHs, the growth range of the trend which could lead to the faster reaction rate was obvious at lower RH. The water content of the droplet was also more likely to reduce rapidly with the loss of the RH from the absorbance changes of 3400 cm-1H2O stretching band dependent upon reaction times. These may be due to irreversible evaporation of HCl gas which is the main driving force for this type of reaction and the NaHMA is a less hygroscopic component compared to H2MA. And the HCl gas is more likely to evaporate faster from the single droplet and promote the reaction rate and the consumption of water content at lower RH. These results could help in understanding the chemical conversion processes of water-soluble dicarboxylic acids to dicarboxylate salts, as well as the consumption of Cl in sea salt aerosols by organic acids in the atmosphere.

Degree of coupling in high-rise mixed shear walls structures

Indian Academy of Sciences (India)

A simple method of analysis is presented to determine the influence of single shear walls (SSW) on the degree of coupling DoC and on the peak shear demand PSD for beams of coupled shear walls (CSW) in mixed shear wall structures (MSW). Non-coupled lateral load resisting structures such as singular planar walls and ...

Reversible conversion of valence-tautomeric copper metal-organic frameworks dependent single-crystal-to-single-crystal oxidation/reduction: a redox-switchable catalyst for C-H bonds activation reaction.

Science.gov (United States)

Huang, Chao; Wu, Jie; Song, Chuanjun; Ding, Ran; Qiao, Yan; Hou, Hongwei; Chang, Junbiao; Fan, Yaoting

2015-06-28

Upon single-crystal-to-single-crystal (SCSC) oxidation/reduction, reversible structural transformations take place between the anionic porous zeolite-like Cu(I) framework and a topologically equivalent neutral Cu(I)Cu(II) mixed-valent framework. The unique conversion behavior of the Cu(I) framework endowed it as a redox-switchable catalyst for the direct arylation of heterocycle C-H bonds.

Hazardous and mixed waste management at UMTRA sites

International Nuclear Information System (INIS)

Hampill, H.G.

1988-01-01

During the early stages of the Uranium Mill Tailings Remedial Action Project, there were some serious questions regarding the ownership of and consequently the responsibility for disposal of hazardous wastes at UMTRA sites. In addition to State and Indian Tribe waste disposal regulations, UMTRA must also conform to guidelines established by the NRC, OSHA, EPA, and DOT. Because of the differing regulatory thrusts of these agencies, UMTRA has to be vigilant in order to ensure that the disposal of each parcel of waste material is in compliance with all regulations. Mixed-waste disposal presents a particularly difficult problem. No single agency is willing to lay claim to the regulation of mixed-wastes, and no conventional waste disposal facility is willing to accept it. Consequently, the disposal of each lot of mixed-waste at UMTRA sites must be handled on a case by case basis. A recently published position paper which spells out UMTRA policy on waste materials indicates that wastes found at UMTRA sites are either residual radioactive wastes, or mixed-wastes, or for the disposal of hazardous waste is determined by the time the original material arrived. If it arrived prior to the termination of the AEC uranium supply contract, its disposal is the responsibility of UMTRA. If it arrived after the end of the contract, the responsibility for disposal lies with the former operator

Solution-grown organic single-crystalline p-n junctions with ambipolar charge transport.

Science.gov (United States)

Fan, Congcheng; Zoombelt, Arjan P; Jiang, Hao; Fu, Weifei; Wu, Jiake; Yuan, Wentao; Wang, Yong; Li, Hanying; Chen, Hongzheng; Bao, Zhenan

2013-10-25

Organic single-crystalline p-n junctions are grown from mixed solutions. First, C60 crystals (n-type) form and, subsequently, C8-BTBT crystals (p-type) nucleate heterogeneously on the C60 crystals. Both crystals continue to grow simultaneously into single-crystalline p-n junctions that exhibit ambipolar charge transport characteristics. This work provides a platform to study organic single-crystalline p-n junctions. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Effectiveness of anode in a solid oxide fuel cell with hydrogen/oxygen mixed gases

Energy Technology Data Exchange (ETDEWEB)

Kellogg, Isaiah D. [Department of Mechanical and Aerospace Engineering, Missouri University of Science and Technology, Rolla, MO (United States); Department of Materials Science and Engineering, Missouri University of Science and Technology, Rolla, MO (United States); Koylu, Umit O. [Department of Mechanical and Aerospace Engineering, Missouri University of Science and Technology, Rolla, MO (United States); Petrovsky, Vladimir; Dogan, Fatih [Department of Materials Science and Engineering, Missouri University of Science and Technology, Rolla, MO (United States)

2009-06-15

A porous Ni/YSZ cermet in mixed hydrogen and oxygen was investigated for its ability to decrease oxygen activity as the anode of a single chamber SOFC. A cell with a dense 300 {mu}m YSZ electrolyte was operated in a double chamber configuration. The Ni-YSZ anode was exposed to a mixture of hydrogen and oxygen of varying compositions while the cathode was exposed to oxygen. Double chamber tests with mixed gas on the anode revealed voltage oscillations linked to lowered power generation and increased resistance. Resistance measurements of the anode during operation revealed a Ni/NiO redox cycle causing the voltage oscillations. The results of these tests, and future tests of similar format, could be useful in the development of single chamber SOFC using hydrogen as fuel. (author)

Mixing states of aerosols over four environmentally distinct atmospheric regimes in Asia: coastal, urban, and industrial locations influenced by dust.

Science.gov (United States)

Ramachandran, S; Srivastava, Rohit

2016-06-01

Mixing can influence the optical, physical, and chemical characteristics of aerosols, which in turn can modify their life cycle and radiative effects. Assumptions on the mixing state can lead to uncertain estimates of aerosol radiative effects. To examine the effect of mixing on the aerosol characteristics, and their influence on radiative effects, aerosol mixing states are determined over four environmentally distinct locations (Karachi, Gwangju, Osaka, and Singapore) in Asia, an aerosol hot spot region, using measured spectral aerosol optical properties and optical properties model. Aerosol optical depth (AOD), single scattering albedo (SSA), and asymmetry parameter (g) exhibit spectral, spatial, and temporal variations. Aerosol mixing states exhibit large spatial and temporal variations consistent with aerosol characteristics and aerosol type over each location. External mixing of aerosol species is unable to reproduce measured SSA over Asia, thus providing a strong evidence that aerosols exist in mixed state. Mineral dust (MD) (core)-Black carbon (BC) (shell) is one of the most preferred aerosol mixing states. Over locations influenced by biomass burning aerosols, BC (core)-water soluble (WS, shell) is a preferred mixing state, while dust gets coated by anthropogenic aerosols (BC, WS) over urban regions influenced by dust. MD (core)-sea salt (shell) mixing is found over Gwangju corroborating the observations. Aerosol radiative forcing exhibits large seasonal and spatial variations consistent with features seen in aerosol optical properties and mixing states. TOA forcing is less negative/positive for external mixing scenario because of lower SSA. Aerosol radiative forcing in Karachi is a factor of 2 higher when compared to Gwangju, Osaka, and Singapore. The influence of g on aerosol radiative forcing is insignificant. Results emphasize that rather than prescribing one single aerosol mixing state in global climate models regionally and temporally varying aerosol

Generation of a single-cycle optical pulse

International Nuclear Information System (INIS)

Shverdin, M.Y.; Walker, D.R.; Yavuz, D.D.; Yin, G.Y.; Harris, S.E.

2005-01-01

We make use of coherent control of four-wave mixing to the ultraviolet as a diagnostic and describe the generation of a periodic optical waveform where the spectrum is sufficiently broad that the envelope is approximately a single-cycle in length, and where the temporal shape of this envelope may be synthesized by varying the coefficients of a Fourier series. Specifically, using seven sidebands, we report the generation of a train of single-cycle optical pulses with a pulse width of 1.6 fs, a pulse separation of 11 fs, and a peak power of 1 MW

Effect of Mixing Process on Polypropylene Modified Bituminous Concrete Mix Properties

OpenAIRE

Noor Zainab Habib; Ibrahim Kamaruddin; Madzalan Napiah; Isa Mohd Tan

2011-01-01

This paper presents a research conducted to investigate the effect of mixing process on polypropylene (PP) modified bitumen mixed with well graded aggregate to form modified bituminous concrete mix. Two mode of mixing, namely dry and wet with different concentration of polymer polypropylene was used with 80/100 pen bitumen, to evaluate the bituminous concrete mix properties. Three percentages of polymer varying from 1-3% by the weight of bitumen was used in this study. Three mixes namely cont...

Local correlations of mixed two-qubit states

International Nuclear Information System (INIS)

Zhang Fulin; Chen Jingling; Ren Changliang; Shi Mingjun

2010-01-01

The quantum probability distribution arising from single-copy von Neumann measurements on an arbitrary two-qubit state is decomposed into the local and nonlocal parts, in the approach of Elitzur, Popescu and Rohrlich [A. Elitzur, S. Popescu, D. Rohrlich, Phys. Lett. A 162 (1992) 25]. A lower bound of the local weight is proved being connected with the concurrence of the state p L max =1-C(ρ). The local probability distributions for two families of mixed states are constructed independently, which accord with the lower bound.

Dynamics of Mixed- Candida Species Biofilms in Response to Antifungals.

Science.gov (United States)

Vipulanandan, G; Herrera, M; Wiederhold, N P; Li, X; Mintz, J; Wickes, B L; Kadosh, D

2018-01-01

Oral infections caused by Candida species, the most commonly isolated human fungal pathogen, are frequently associated with biofilms. Although Candida albicans is the predominant organism found in patients with oral thrush, a biofilm infection, there is an increasing incidence of oral colonization and infections caused by non- albicans Candida species, including C. glabrata, C. dubliniensis, and C. tropicalis, which are frequently more resistant to antifungal treatment. While single-species Candida biofilms have been well studied, considerably less is known about the dynamics of mixed- Candida species biofilms and how these dynamics are altered by antifungal treatment. To address these questions, we developed a quantitative polymerase chain reaction-based approach to determine the precise species composition of mixed- Candida species biofilms formed by clinical isolates and laboratory strains in the presence and absence of clinically relevant concentrations of 3 commonly used antifungals: fluconazole, caspofungin, and amphotericin B. In monospecies biofilms, fluconazole exposure favored growth of C. glabrata and C. tropicalis, while caspofungin generally favored significant growth of all species to a varying degree. Fluconazole was not effective against preformed mixed- Candida species biofilms while amphotericin B was potent. As a general trend, in mixed- Candida species biofilms, C. albicans lost dominance in the presence of antifungals. Interestingly, presence in mixed versus monospecies biofilms reduced susceptibility to amphotericin B for C. tropicalis and C. glabrata. Overall, our data suggest that antifungal treatment favors the growth of specific non- albicans Candida species in mixed- Candida species biofilms.

Harnessing the mode mixing in optical fiber-tip cavities

International Nuclear Information System (INIS)

Podoliak, Nina; Horak, Peter; Takahashi, Hiroki; Keller, Matthias

2017-01-01

We present a systematic numerical study of Fabry–Pérot optical cavities with Gaussian-shape mirrors formed between tips of optical fibers. Such cavities can be fabricated by laser machining of fiber tips and are promising systems for achieving strong coupling between atomic particles and an optical field as required for quantum information applications. Using a mode mixing matrix method, we analyze the cavity optical eigenmodes and corresponding losses depending on a range of cavity-shape parameters, such as mirror radius of curvature, indentation depth and cavity length. The Gaussian shape of the mirrors causes mixing of optical modes in the cavity. We investigate the effect of the mode mixing on the coherent atom-cavity coupling as well as the mode matching between the cavity and a single-mode optical fiber. While the mode mixing is associated with increased cavity losses, it can also lead to an enhancement of the local optical field. We demonstrate that around the resonance between the fundamental and 2nd order Laguerre–Gaussian modes of the cavity it is possible to obtain 50% enhancement of the atom-cavity coupling at the cavity center while still maintaining low cavity losses and high cavity-fiber optical coupling. (paper)

Formation of mixed and patterned self-assembled films of alkylphosphonates on commercially pure titanium surfaces

Energy Technology Data Exchange (ETDEWEB)

Rudzka, Katarzyna; Sanchez Treviño, Alda Y.; Rodríguez-Valverde, Miguel A., E-mail: marodri@ugr.es; Cabrerizo-Vílchez, Miguel A.

2016-12-15

Highlights: • Chemically-tailored titanium surfaces were prepared by self-assembly of alkylphosphonates. • Mixed self-assembled films were prepared with aqueous mixtures of two alkylphosphonates. • Single self-assembled films were altered by laser abrasion. • Mixed and patterned self-assembled films on titanium may guide the bone-like formation. - Abstract: Titanium is extensively employed in biomedical devices, in particular as implant. The self-assembly of alkylphosphonates on titanium surfaces enable the specific adsorption of biomolecules to adapt the implant response against external stimuli. In this work, chemically-tailored cpTi surfaces were prepared by self-assembly of alkylphosphonate molecules. By bringing together attributes of two grafting molecules, aqueous mixtures of two alkylphosphonates were used to obtain mixed self-assembled films. Single self-assembled films were also altered by laser abrasion to produce chemically patterned cpTi surfaces. Both mixed and patterned self-assembled films were confirmed by AFM, ESEM and X-ray photoelectron spectroscopy. Water contact angle measurements also revealed the composition of the self-assembly films. Chemical functionalization with two grafting phosphonate molecules and laser surface engineering may be combined to guide the bone-like formation on cpTi, and the future biological response in the host.

A Bayesian analysis of the mixed labelling phenomenon in two-target tracking

NARCIS (Netherlands)

Aoki, E.H.; Boers, Y.; Svensson, L.; Mandal, Pranab K.; Bagchi, Arunabha

In mulit-target tracking and labelling (MTTL), mixed labelling corresponds to a situation where there is ambiguity in labelling, i.e. in the assignment of labels to locations (where a "location" here means simply an unlabelled single-target state. The phenomenon is well-known in literature, and

Experimental investigation of turbulent mixing by Rayleigh-Taylor instability

International Nuclear Information System (INIS)

Youngs, D.L.

1992-01-01

A key feature of compressible turbulent mixing is the generation of vorticity via the ∇px ∇(1/ρ) term. This source of vorticity is also present in incompressible flows involving the mixing of fluids of different density, for example Rayleigh-Taylor unstable flows. This paper gives a summary of an experimental investigation of turbulent mixing at a plane boundary between two fluids, of densities ρ 1 , and ρ 2 . (ρ 1 > ρ 2 ) due to Rayleigh-Taylor instability. The two fluids are near incompressible and mixing occurs when an approximately constant acceleration, g, is applied normal to the interface with direction from fluid 2 to fluid 1. Full details of the experimental programme are given in a set of three reports. Some of the earlier experiments are also described by Read. Previous experimental work and much of the theoretical research has concentrated on studying the growth of the instability from a single wavelength perturbation rather than turbulent mixing. Notable exceptions are published in the Russian literature. A related process, turbulent mixing induced by the passage of shock waves though an interface between fluids of different density is described by Andronov et al. The major purpose of the experiments described here was to study the evolution of the instability from small random perturbations where it is found that large and larger structures appear as time proceeds. A novel technique was used to provide the desired acceleration. The two fluids were enclosed in a rectangular tank, the lighter fluid 2 initially resting on top of the denser fluid 1. One or more rocket motors were then used to drive the tank vertically downwards. The aim of the experimental programme is to provide data for the calibration of a turbulence model used to predict mixing in real situations

Chemical vapor composites (CVC)

International Nuclear Information System (INIS)

Reagan, P.

1993-01-01

The Chemical Vapor Composite, CVC trademark , process fabricates composite material by simply mixing particles (powders and or fibers) with CVD reactants which are transported and co-deposited on a hot substrate. A key feature of the CVC process is the control provided by varing the density, geometry (aspect ratio) and composition of the entrained particles in the matrix material, during deposition. The process can fabricate composite components to net shape (± 0.013 mm) on a machined substrate in a single step. The microstructure of the deposit is described and several examples of different types of particles in the matrix are illustrated. Mechanical properties of SiC composite material fabricated with SiC powder and fiber will be presented. Several examples of low cost ceramic composite products will be shown. (orig.)

Distributed simulation of mixing flow of dough

International Nuclear Information System (INIS)

Baloch, A.

2005-01-01

This paper reports on a study concerned with the numerical simulation of incompressible complex mixing flows of viscoelastic fluids is of industrial importance, particularly relevance in the food processing industry, such as occurs in dough mixing. The flows considered are in a complex domain setting. The present problem is one of this form, expressed as the flow between an outer rotating cylindrical vessel all and a stationary cylindrical/stirrers. The context is one of mixing with in a cylindrical vessel, where stirrers are located on the mixing vessel lid, and placed in a concentric/eccentric position with respect to the central cylindrical axis of the vessel. Here, the motion is considered as driven by the rotation of the outer vessel wall, with various stirrer locations. Two dough mixers at various rotation speeds are studied; one with one stirrer and the other with two stirrers. With a singular circular stirrer, an eccentric configuration is adopted. A further eccentric case with two circular stirrers is also contrasted against the above, where a symmetrical arrangement is assumed. Numerical simulations are based on two dimensions in the cylindrical polar co-ordinates system. The results reflected close agreement with the equivalent experimental results. The motivation for this work is to develop and advance technology to model the mixing of dough. The ultimate target is to predict and adjust the design of dough mixers, so that optimal dough processing may be achieved notably, with reference to work input on the dough. The hardware platform is a network combination of homogeneous Intel Linux clusters of workstations. A semi-implicit time-stepping Taylor-Galerkin scheme is employed with PVM (Parallel Virtual Machine) message passing libraries as the message passing protocol. Parallel results are compared against single processor (sequentially) solutions, using the parallelism paradigm of domain decomposition. Linear speed-up with the number of processors is

White-light phosphorescence emission from a single molecule: application to OLED.

Science.gov (United States)

Bolink, Henk J; De Angelis, Filippo; Baranoff, Etienne; Klein, Cédric; Fantacci, Simona; Coronado, Eugenio; Sessolo, Michele; Kalyanasundaram, K; Grätzel, Michael; Nazeeruddin, Md K

2009-08-21

A simple mononuclear cyclometallated iridium(iii) complex exhibits white photo- and electro- luminescence in the wavelength range from 440 to 800 nm, which originates from a single emitting excited state of mixed character.

Multiple scattering of light by water cloud droplets with external and internal mixing of black carbon aerosols

International Nuclear Information System (INIS)

Wang Hai-Hua; Sun Xian-Ming

2012-01-01

The mixture of water cloud droplets with black carbon impurities is modeled by external and internal mixing models. The internal mixing model is modeled with a two-layered sphere (water cloud droplets containing black carbon (BC) inclusions), and the single scattering and absorption characteristics are calculated at the visible wavelength of 0.55 μm by using the Lorenz—Mie theory. The external mixing model is developed assuming that the same amount of BC particles are mixed with the water droplets externally. The multiple scattering characteristics are computed by using the Monte Carlo method. The results show that when the size of the BC aerosol is small, the reflection intensity of the internal mixing model is bigger than that of the external mixing model. However, if the size of the BC aerosol is big, the absorption of the internal mixing model will be larger than that of the external mixing model. (electromagnetism, optics, acoustics, heat transfer, classical mechanics, and fluid dynamics)

Mixed Cultures Fermentation for the Production of Poly-ß-hydroxybutyrate

Directory of Open Access Journals (Sweden)

Thomas Shalin

2014-10-01

Full Text Available Poly-ß-hydroxybutyrate (PHB is a biodegradable intracellular microbial product produced by many bacteria and it is comparable to some of the petrochemical derived thermoplastics such as polypropylene. One of the main barriers for the commercial exploitation is the high cost of the substrate for the production of biopolymer. The utilization of mixed microbial cultures facilitates the use of complex substrates thereby reducing the cost of PHB production. In the present study, mixed culture systems were evaluated for PHB production. Bacillus firmus NII 0830 was used for the production of PHB since it accumulates a large amount of PHB and a second organism Lactobacillus delbrueckii NII 0925 was used to provide lactic acid. FTIR and 1H NMR analyses revealed that the PHB extracted from pure culture and mixed culture showed exact match to that of standard PHB. Biodegradation studies of the PHB blends showed 87% degradation. It was also found that a consortium of organisms degraded the films faster than a single organism.

A microfluidic galvanic cell on a single layer of paper

Science.gov (United States)

Purohit, Krutarth H.; Emrani, Saina; Rodriguez, Sandra; Liaw, Shi-Shen; Pham, Linda; Galvan, Vicente; Domalaon, Kryls; Gomez, Frank A.; Haan, John L.

2016-06-01

Paper microfluidics is used to produce single layer galvanic and hybrid cells to produce energy that could power paper-based analytical sensors. When two aqueous streams are absorbed onto paper to establish co-laminar flow, the streams stay in contact with each other with limited mixing. The interface at which mixing occurs acts as a charge-transfer region, eliminating the need for a salt bridge. We designed a Cusbnd Zn galvanic cell that powers an LED when two are placed in series. We also used more powerful redox couples (formate and silver, formate and permanganate) to produce higher power density (18 and 3.1 mW mg-1 Pd). These power densities are greater than previously reported paper microfluidic fuel cells using formate or methanol. The single layer design is much more simplified than previous reports of multi-layer galvanic cells on paper.

Summary of Group Development and Testing for Single Shell Tank Closure at Hanford

International Nuclear Information System (INIS)

Harbour, John R.

2005-01-01

This report is a summary of the bench-scale and large scale experimental studies performed by Savannah River National Laboratory for CH2M HILL to develop grout design mixes for possible use in producing fill materials as a part of Tank Closure of the Single-Shell Tanks at Hanford. The grout development data provided in this report demonstrates that these design mixes will produce fill materials that are ready for use in Hanford single shell tank closure. The purpose of this report is to assess the ability of the proposed grout specifications to meet the current requirements for successful single shell tank closure which will include the contracting of services for construction and operation of a grout batch plant. The research and field experience gained by SRNL in the closure of Tanks 17F and 20F at the Savannah River Site was leveraged into the grout development efforts for Hanford. It is concluded that the three Hanford grout design mixes provide fill materials that meet the current requirements for successful placement. This conclusion is based on the completion of recommended testing using Hanford area materials by the operators of the grout batch plant. This report summarizes the regulatory drivers and the requirements for grout mixes as tank fill material. It is these requirements for both fresh and cured grout properties that drove the development of the grout formulations for the stabilization, structural and capping layers

Transition States from Empirical Force Fields

DEFF Research Database (Denmark)

Jensen, Frank; Norrby, Per-Ola

2003-01-01

This is an overview of the use of empirical force fields in the study of reaction mechanisms. EVB-type methods (including RFF and MCMM) produce full reaction surfaces by mixing, in the simplest case, known force fields describing reactants and products. The SEAM method instead locates approximate...

Direct numerical simulation of turbulent mixing in grid-generated turbulence

International Nuclear Information System (INIS)

Nagata, Kouji; Suzuki, Hiroki; Sakai, Yasuhiko; Kubo, Takashi; Hayase, Toshiyuki

2008-01-01

Turbulent mixing of passive scalar (heat) in grid-generated turbulence (GGT) is simulated by means of direct numerical simulation (DNS). A turbulence-generating grid, on which the velocity components are set to zero, is located downstream of the channel entrance, and it is numerically constructed on the staggered mesh arrangement using the immersed boundary method. The grid types constructed are: (a) square-mesh biplane grid, (b) square-mesh single-plane grid, (c) composite grid consisting of parallel square-bars and (d) fractal grid. Two fluids with different temperatures are provided separately in the upper and lower streams upstream of the turbulence-generating grids, generating the thermal mixing layer behind the grids. For the grid (a), simulations for two different Prandtl numbers of 0.71 and 7.1, corresponding to air and water flows, are conducted to investigate the effect of the Prandtl number. The results show that the typical grid turbulence and shearless mixing layer are generated downstream of the grids. The results of the scalar field show that a typical thermal mixing layer is generated as well, and the effects of the Prandtl numbers on turbulent heat transfer are observed.

Direct numerical simulation of turbulent mixing in grid-generated turbulence

Energy Technology Data Exchange (ETDEWEB)

Nagata, Kouji; Suzuki, Hiroki; Sakai, Yasuhiko; Kubo, Takashi [Department of Mechanical Science and Engineering, Nagoya University, Nagoya 464-8603 (Japan); Hayase, Toshiyuki [Institute of Fluid Science, Tohoku University, Sendai 980-8577 (Japan)], E-mail: nagata@nagoya-u.jp, E-mail: hsuzuki@nagoya-u.jp, E-mail: ysakai@mech.nagoya-u.ac.jp, E-mail: t-kubo@nagoya-u.jp, E-mail: hayase@ifs.tohoku.ac.jp

2008-12-15

Turbulent mixing of passive scalar (heat) in grid-generated turbulence (GGT) is simulated by means of direct numerical simulation (DNS). A turbulence-generating grid, on which the velocity components are set to zero, is located downstream of the channel entrance, and it is numerically constructed on the staggered mesh arrangement using the immersed boundary method. The grid types constructed are: (a) square-mesh biplane grid, (b) square-mesh single-plane grid, (c) composite grid consisting of parallel square-bars and (d) fractal grid. Two fluids with different temperatures are provided separately in the upper and lower streams upstream of the turbulence-generating grids, generating the thermal mixing layer behind the grids. For the grid (a), simulations for two different Prandtl numbers of 0.71 and 7.1, corresponding to air and water flows, are conducted to investigate the effect of the Prandtl number. The results show that the typical grid turbulence and shearless mixing layer are generated downstream of the grids. The results of the scalar field show that a typical thermal mixing layer is generated as well, and the effects of the Prandtl numbers on turbulent heat transfer are observed.

Two-phase turbulent mixing and buoyancy drift in rod bundles

International Nuclear Information System (INIS)

Carlucci, L.N.; Hammouda, N.; Rowe, D.S.

2004-01-01

This paper describes the development of generalized relationships for single- and two-phase inter subchannel turbulent mixing in vertical and horizontal flows, and lateral buoyancy drift in horizontal flows. The relationships for turbulent mixing, together with a recommended one for void drift, have been implemented in a subchannel thermal hydraulics code, and assessed using a range of data on enthalpy migration in vertical steam-water lows under BWR and PWR diabatic conditions. The intent of this assessment as to optimize these relationships to give the best agreement with the enthalpy migration data for vertical flows. The optimized turbulent mixing relationships were then used as a basis to benchmark a proposed buoyancy rift model to give the best predictions of void and enthalpy migration data n horizontal flows typical of PHWR CANDU reactor operation under normal and off-normal conditions. Overall, the optimized turbulent mixing and buoyancy drift relationships have been found to predict the available data quite well, nd generally better and more consistently than currently used models. This is expected to result in more accurate calculations of subchannel distributions of phasic flows, and hence, in improved predictions of critical heat flux (CHF)

Design of a High Intensity Turbulent Combustion System

Science.gov (United States)

2015-05-01

mixing of the reactants in chemical reactors, boilers , furnaces and mixing of fuel and air in engines take place in turbulent flow. One of the most...determining flame speed. When a tube containing combustible mixture, the flame speed is the propagation speed of the flame front towards the unburned...stress criteria is effective when the material is ductile in nature. This stress theory is developed from the 44 ’distortion energy failure theory

Invisible Higgs decays from Higgs-graviscalar mixing

International Nuclear Information System (INIS)

Dominici, Daniele; Gunion, John F.

2009-01-01

We recompute the invisible Higgs decay width arising from Higgs-graviscalar mixing in the Arkani-Hamed, Dimopoulos, Dvali model, comparing the original derivation in the nondiagonal mass basis to that in a diagonal mass basis. The results obtained are identical (and differ by a factor of 2 from the original calculation) but the diagonal-basis derivation is pedagogically useful for clarifying the physics of the invisible width from mixing. We emphasize that both derivations make it clear that a direct scan in energy for a process such as WW→WW mediated by Higgs plus graviscalar intermediate resonances would follow a single Breit-Wigner form with total width given by Γ tot =Γ h SM +Γ invisible . We also compute the additional contributions to the invisible width due to direct Higgs to graviscalar-pair decays. We find that the invisible width due to the latter is relatively small, unless the Higgs mass is comparable to or larger than the effective extra-dimensional Planck mass.

Yield of single-strand breaks in the DNA of E.coli 10 msec after irradiation

International Nuclear Information System (INIS)

Fox, R.A.; Fielden, E.M.; Sapora, O.

1976-01-01

The rapid mixing of 0.3M alkali with a suspension of E.coli B/r 6 +- 3 and 144 +- 3 msec after irradiation with electrons (4.3 MeV, 0 to 50 krad) has been used to make a comparison of the yields of single strand breaks in the presence and absence of oxygen. No significant difference was observed between the numbers of single strand breaks appearing at 6 and 144 msec after irradiation. Assuming that mixing with alkali inactivates the cellular repair enzymes within several milliseconds, these results indicate that enzymic repair does not operate within this time scale. It seems probable that radiation chemical processes are responsible for the initial oxygen effect on single strand breaks. (U.K.)

Catalytic distillation process

Science.gov (United States)

Smith, L.A. Jr.

1982-06-22

A method is described for conducting chemical reactions and fractionation of the reaction mixture comprising feeding reactants to a distillation column reactor into a feed zone and concurrently contacting the reactants with a fixed bed catalytic packing to concurrently carry out the reaction and fractionate the reaction mixture. For example, a method for preparing methyl tertiary butyl ether in high purity from a mixed feed stream of isobutene and normal butene comprising feeding the mixed feed stream to a distillation column reactor into a feed zone at the lower end of a distillation reaction zone, and methanol into the upper end of said distillation reaction zone, which is packed with a properly supported cationic ion exchange resin, contacting the C[sub 4] feed and methanol with the catalytic distillation packing to react methanol and isobutene, and concurrently fractionating the ether from the column below the catalytic zone and removing normal butene overhead above the catalytic zone.

Ion beam mixing isotopic metal bilayers

Energy Technology Data Exchange (ETDEWEB)

Fell, C.J. [Newcastle Univ., NSW (Australia). Dept. of Physics; Kenny, M.J. [CSIRO, Lindfield, NSW (Australia). Div. of Applied Physics

1993-12-31

In order to obtain an insight into the mechanisms of ion-solid interactions, bilayer targets can be prepared from two different isotopes. A mixing study SIMS is to be carried out using specially grown monocrystalline bilayers of {sup 58}Ni / {sup 60}Ni. An important aspect of the work is the preparation of high quality single-crystal thin films. The Ni layers will be grown on the (110) surface of pure Ni and verified for crystallinity using Reflection High-Energy Electron Diffraction and Rutherford Backscattering channelling analysis. The Pd bilayers will be grown on a Pd (100) surface. RHEED will be used to confirm the two-dimensional crystallinity of the surface before and after deposition of each layer, and channelling used to confirm bulk film crystallinity. Single crystal substrates are currently being prepared. Analysis of the Ni (110) surface using RHEED at 9 kV shows a streak spacing which corresponds to a lattice spacing of 2.47 {+-} 0.09 Angstroms. 9 refs., 1 fig.

Ion beam mixing isotopic metal bilayers

Energy Technology Data Exchange (ETDEWEB)

Fell, C J [Newcastle Univ., NSW (Australia). Dept. of Physics; Kenny, M J [CSIRO, Lindfield, NSW (Australia). Div. of Applied Physics

1994-12-31

In order to obtain an insight into the mechanisms of ion-solid interactions, bilayer targets can be prepared from two different isotopes. A mixing study SIMS is to be carried out using specially grown monocrystalline bilayers of {sup 58}Ni / {sup 60}Ni. An important aspect of the work is the preparation of high quality single-crystal thin films. The Ni layers will be grown on the (110) surface of pure Ni and verified for crystallinity using Reflection High-Energy Electron Diffraction and Rutherford Backscattering channelling analysis. The Pd bilayers will be grown on a Pd (100) surface. RHEED will be used to confirm the two-dimensional crystallinity of the surface before and after deposition of each layer, and channelling used to confirm bulk film crystallinity. Single crystal substrates are currently being prepared. Analysis of the Ni (110) surface using RHEED at 9 kV shows a streak spacing which corresponds to a lattice spacing of 2.47 {+-} 0.09 Angstroms. 9 refs., 1 fig.

Analysis of baseline, average, and longitudinally measured blood pressure data using linear mixed models.

Science.gov (United States)

Hossain, Ahmed; Beyene, Joseph

2014-01-01

This article compares baseline, average, and longitudinal data analysis methods for identifying genetic variants in genome-wide association study using the Genetic Analysis Workshop 18 data. We apply methods that include (a) linear mixed models with baseline measures, (b) random intercept linear mixed models with mean measures outcome, and (c) random intercept linear mixed models with longitudinal measurements. In the linear mixed models, covariates are included as fixed effects, whereas relatedness among individuals is incorporated as the variance-covariance structure of the random effect for the individuals. The overall strategy of applying linear mixed models decorrelate the data is based on Aulchenko et al.'s GRAMMAR. By analyzing systolic and diastolic blood pressure, which are used separately as outcomes, we compare the 3 methods in identifying a known genetic variant that is associated with blood pressure from chromosome 3 and simulated phenotype data. We also analyze the real phenotype data to illustrate the methods. We conclude that the linear mixed model with longitudinal measurements of diastolic blood pressure is the most accurate at identifying the known single-nucleotide polymorphism among the methods, but linear mixed models with baseline measures perform best with systolic blood pressure as the outcome.

Optimization of gas mixing system of premixed burner based on CFD analysis

International Nuclear Information System (INIS)

Zhang, Tian-Hu; Liu, Feng-Guo; You, Xue-Yi

2014-01-01

Highlights: • New multi-ejectors gas mixing system for premixed combustion burner is provided. • Two measures are proposed to improve the flow uniformity at the outlet of GMS. • Small improvement of uniformity induces significant decrease of pollutant emission. • Uniformity of velocity and fuel–gas mixing of ejector increases 234.2% and 2.9%. • Uniformity of flow rate and fuel–gas mixing of ejectors increases 1.9% and 2.2%. - Abstract: The optimization of gas mixing system (GMS) of premixed burner is presented by Computational Fluid Dynamics (CFD) and the uniformity at the outlet of GMS is proved experimentally to have strong influence on pollutant emission. To improve the uniformity at the outlet of GMS, the eleven distribution orifice plates and a diversion plate are introduced. The quantified analysis shows that the uniformity at the outlet of GMS is improved significantly. With applying the distribution orifice plates, the uniformity of velocity and fuel–gas mixing of single ejector is increased by 234.2% and 2.9%, respectively. With applying the diversion plate, the uniformity of flow rate and fuel–gas mixing of different ejectors is increased by 1.9% and 2.2%, respectively. The optimal measures and geometrical parameters provide an applicable guidance for the design of commercial premixed burner

Impacts of Subgrid Heterogeneous Mixing between Cloud Liquid and Ice on the Wegner-Bergeron-Findeisen Process and Mixed-phase Clouds in NCAR CAM5

Science.gov (United States)