WorldWideScience

Sample records for simple shadow shield

  1. Results of substitution of the Nal by a Ge detector in a simple shadow shield whole body counter

    Energy Technology Data Exchange (ETDEWEB)

    Sahre, P.; Schoenmuth, T. [Nuclear Engineering and Analytics Inc. Rossendorf, Dresden (Germany); Thieme, K. [Amersham Buchler Ltd. und Co., Braunschweig (Germany)

    1997-12-01

    Since 1976 a whole body counter (WBC) has been used at the Rossendorf Research Centre for measuring the internal contamination of workers. The WBC with the Germanium detector is given schematically and visually. The WBC is a shadow shield type with a tilted chair having only one detector. Table 1 contains the parameters of the WBC. It can be seen that the WBC is a simple counter. Therefore, taking into account the experiences of McCurdy, a lot of improvements were expected form the simple substitution of a HP Germanium detector for a NaI (TI) detector, i.e. despite a decrease in the sensitive detection volume, an enhancement of all quantifiable results (e.g. lower limit of detection and time for analysis of the spectrum) and above all the reliability and automation of nuclide identification were expected. (orig./SR)

  2. Simple Impact Crater Shapes From Shadows - The Sequel

    Science.gov (United States)

    Chappelow, J. E.

    2008-12-01

    At the last LPSC meeting I presented the outline of a method for determining simple impact crater shapes from shadows. In theory the shadow cast within a simple crater provides enough information to derive its cross-sectional shape from shadow measurements, at least to the maximum depth to which the shadow extends. Under certain simple assumptions, this can be done analytically. If the crater is conic-section - shaped, then it can be shown that the down-sun bound of any shadow cast within it is elliptical, with one axis along the direction of illumination and the other (perpendicular to it) of semi-length D/2 (where D is diameter). The properties of this shadow-ellipse can be related to the parameters of the crater shape conic-section, thus measurements of the shadow-ellipse yield not only crater depth and diameter but also the approximate crater shape, in terms of conic sections. The method also does not depend upon the shadow crossing near the crater center, which avoids a pitfall of older shadow measurement methods. The technique is also amenable to computer implementation, which has already been largely completed. Once computerized, crater measurements can be made rapidly and repeatably. The program reads in an image, its resolution, and the solar elevation and azimuth. The user then defines the crater rim by 'clicking' on three points, and the shadow ellipse by clicking on two more. The program calculates and outputs the diameter, the depth, and parameters describing the crater's approximating conic-section. It is highly applicable to situations where only single-image photography is available, for example MESSENGER flybys of Mercury. At the meeting I will present the finished math for this method and give some examples of its use.

  3. Design, fabrication and commissioning of motorized scanning bed mechanism for shadow shield whole body counting system

    International Nuclear Information System (INIS)

    Arun, B.; Varalakshimi, S.; Manohari, M.; Mathiyarasu, R.

    2012-01-01

    A new scanning bed mechanism for shadow shield counting system is designed, fabricated and commissioned at RSD, IGCAR. The present motorized scanning bed mechanism has varying scan speeds, state of art limit sensors, smooth bed movement, touch screen based software controlled operation parameters with UPS power back-up. In view of the improved personnel safety the entire system has been designed to operate with low voltage power supply (24V). The evaluation demonstrated that the incorporation of the new motorized scanning mechanism has not affected the counting performance of the shadow shield wholebody counting system. (author)

  4. How to use 3D shadows for simple microscopy and vibrometry

    Science.gov (United States)

    Parikesit, Gea O. F.; Kusumaningtyas, Indraswari

    2017-07-01

    In 2014, we reported that shadows can be displayed in 3D using a stereoscopic setup. We now report that the 3D shadows can also be used to perform simple measurements, which are suitable for physics education in schools and colleges. Two different types of measurements are demonstrated, i.e. microscopy and vibrometry. Both types of measurements take advantage of the geometrical optics of the 3D shadows, where the 3D position of an object can be estimated using the coordinates of the colored light sources and the coordinates of the colored shadow images. We also include several student activities that can raise the students’ curiosity and capability.

  5. Application of a simple analytical model to estimate effectiveness of radiation shielding for neutrons

    International Nuclear Information System (INIS)

    Frankle, S.C.; Fitzgerald, D.H.; Hutson, R.L.; Macek, R.J.; Wilkinson, C.A.

    1993-01-01

    Neutron dose equivalent rates have been measured for 800-MeV proton beam spills at the Los Alamos Meson Physics Facility. Neutron detectors were used to measure the neutron dose levels at a number of locations for each beam-spill test, and neutron energy spectra were measured for several beam-spill tests. Estimates of expected levels for various detector locations were made using a simple analytical model developed for 800-MeV proton beam spills. A comparison of measurements and model estimates indicates that the model is reasonably accurate in estimating the neutron dose equivalent rate for simple shielding geometries. The model fails for more complicated shielding geometries, where indirect contributions to the dose equivalent rate can dominate

  6. A simple approach to atom probe sample preparation by using shadow masks.

    Science.gov (United States)

    Felfer, Peter; McCarroll, Ingrid; Macauley, Chandra; Cairney, Julie M

    2016-01-01

    Here, we present a new method that utilises shadow masks in a broad ion beam system to prepare atom probe samples. It is particularly suited to non-conductors and materials with surface layers such as surface oxides, implanted layers or thin films. This new approach bypasses the focused ion beam (FIB) lift-out step, increasing the sample throughput, dramatically reducing the required FIB beam time and decreasing the complexity of sample preparation. Copyright © 2015 Elsevier B.V. All rights reserved.

  7. Simple shielding reduces dose to the contralateral breast during prone breast cancer radiotherapy

    Energy Technology Data Exchange (ETDEWEB)

    Goyal, Uma, E-mail: uma.goyal@gmail.com; Locke, Angela; Smith-Raymond, Lexie; Georgiev, Georgi N.

    2016-07-01

    shielded dose means were 12.68 and 1.54 cGy, respectively. When comparing medial and lateral portions of the contralateral bolus-based doses without and with Pb, the shield significantly reduced dose to both sides of the contralateral breast (medial p = 2.64 × 10{sup −14}, lateral p = 4.91 × 10{sup −6}). The prone 0.2-cm Pb shield significantly reduced scatter dose to the contralateral breast on the order of 2 to 3 times. Reductions may be clinically relevant for women younger than 45 years by decreasing the risk of contralateral radiation-induced breast cancer in patients receiving radiation therapy for breast cancer. This shield is simple as it would be a part of the prone breast board during treatments, but future studies are warranted for safety and efficacy clinically.

  8. A Simple Accounting-based Valuation Model for the Debt Tax Shield

    Directory of Open Access Journals (Sweden)

    Andreas Scholze

    2010-05-01

    Full Text Available This paper describes a simple way to integrate the debt tax shield into an accounting-based valuation model. The market value of equity is determined by forecasting residual operating income, which is calculated by charging operating income for the operating assets at a required return that accounts for the tax benefit that comes from borrowing to raise cash for the operations. The model assumes that the firm maintains a deterministic financial leverage ratio, which tends to converge quickly to typical steady-state levels over time. From a practical point of view, this characteristic is of particular help, because it allows a continuing value calculation at the end of a short forecast period.

  9. A simple technique for an accurate shielding of the lungs during total body irradiation

    Directory of Open Access Journals (Sweden)

    Hana Mekdash

    2017-09-01

    Conclusion: This new technique succeeded in reducing the length of the overall treatment session of the conventional TBI procedure and hence reduced patient discomfort while ensuring accurate shielding of the lungs.

  10. Shadow art

    KAUST Repository

    Mitra, Niloy J.

    2009-01-01

    "To them, I said, the truth would be literally nothing but the shadows of the images." - Plato, The Republic Shadow art is a unique form of sculptural art where the 2D shadows cast by a 3D sculpture are essential for the artistic effect. We introduce computational tools for the creation of shadow art and propose a design process where the user can directly specify the desired shadows by providing a set of binary images and corresponding projection information. Since multiple shadow images often contradict each other, we present a geometric optimization that computes a 3D shadow volume whose shadows best approximate the provided input images. Our analysis shows that this optimization is essential for obtaining physically realizable 3D sculptures. The resulting shadow volume can then be modified with a set of interactive editing tools that automatically respect the often intricate shadow constraints. We demonstrate the potential of our system with a number of complex 3D shadow art sculptures that go beyond what is seen in contemporary art pieces. © 2009 ACM.

  11. Cardiac avoidance in breast radiotherapy: a comparison of simple shielding techniques with intensity-modulated radiotherapy

    International Nuclear Information System (INIS)

    Landau, David; Adams, Elizabeth J.; Webb, Steve; Ross, Gillian

    2001-01-01

    Background and purpose: Adjuvant breast radiotherapy (RT) is now part of the routine care of patients with early breast cancer. However, analysis of the Early Breast Cancer Trialists' Collaborative suggests that patients with the lowest risk of dying of breast cancer are at significant risk of cardiac mortality due to longer relapse-free survival. Patients with a significant amount of heart in the high-dose volume have been shown to be at risk of fatal cardiac events. This study was designed to assess whether conformal planning or intensity-modulated radiotherapy (IMRT) techniques allow reduced cardiac irradiation whilst maintaining full target coverage. Material and methods: Ten patients with early breast cancer were available for computed tomography (CT) planning. Each had at least 1 cm maximum heart depth within the posterior border of conventional tangents. For each patient, plans were generated and compared using dose volume histograms for planning target volume (PTV) and organs at risk. The plans included conventional tangents with and without shielding. The shielding was designed to either completely spare the heart or to shield as much heart as possible without compromising PTV coverage. IMRT plans were also prepared using two- and four-field tangential and six-field arc-like beam arrangements. Results: PTV homogeneity was better for the tangential IMRT techniques. For all patients, cardiac irradiation was reduced by the addition of partial cardiac shielding to conventional tangents, without compromise of PTV coverage. The two- and four-field IMRT techniques also reduced heart doses. The average percentage volume of heart receiving >60% of the prescription dose was 4.4% (range 1.0-7.1%) for conventional tangents, 1.5% (0.2-3.9%) for partial shielding, 2.3% (0.5-4.6%) for the two-field IMRT technique and 2.2% (0.4-5.6%) for the four-field IMRT technique. For patients with larger maximum heart depths the four-field IMRT plan achieved greater heart sparing

  12. A simple method for correcting the neutron self-shielding effect of matrix and improving the analytical response in prompt gamma-ray neutron activation analysis

    International Nuclear Information System (INIS)

    Sudarshan, K.; Tripathi, R.; Nair, A.G.C.; Acharya, R.; Reddy, A.V.R.; Goswami, A.

    2005-01-01

    A simple method using an internal standard is proposed to correct for the self-shielding effect of B, Cd and Gd in a matrix. This would increase the linear dynamic range of PGNAA in analyzing samples containing these elements. The method is validated by analyzing synthetic samples containing large amounts of B, Cd, Hg and Gd, the elements having high neutron absorption cross-section, in aqueous solutions and solid forms. A simple Monte-Carlo simulation to find the extent of self-shielding in the matrix is presented. The method is applied to the analysis of titanium boride alloy containing large amount of boron. The satisfactory results obtained showed the efficacy of the method of correcting for the self-shielding effects in the sample

  13. Dostoevsky's Shadows

    Directory of Open Access Journals (Sweden)

    Ioana Cristina Nicolae

    2016-04-01

    Full Text Available In this paper, I bring to light Jung’s Shadow archetype in Dostoevsky’s works and also analyzes their implications in the structure of his characters. Taking into account that the Russian writer’s creation is vast, I shall select a limited number of his works, namely ‘The Possessed’; ‘Crime and Punishment’; ‘The Brothers Karamazov’; ‘Notes from Underground’ and ‘The Double’. We are all burdened with our Shadow and must strive to overcome it, but what happens if we fail or never even try to master it? Raskolnikov’s attempt to free himself from the chains of his Shadow was too late, he had already committed the murder, but not in vain, he succeeded in redeeming himself, and so his effort must be taken into account. This does not help him to avoid the punishment, but offers him a chance after serving it. On the other hand, Smerdyakov’s case is different: he made no attempt to overcome his Shadow, the only argument that he brought in his favor being that he acted fuelled by the desire of fulfilling his brother’s wish. It is clear that, he has no chance for a better future and the fault lies with him because he did not create that chance. Dostoevsky’s characters always seem to be ruled by a tragic destiny, an unlucky fate from which they cannot escape.

  14. Shadow Soldiering

    DEFF Research Database (Denmark)

    Mynster Christensen, Maya

    question the thesis pursues is how the processes of mobilisation connecting these constellations are facilitated, and how the constellations are constituted in the intersection between local and global formations. Shadow soldiering, it is argued, is not a phenomenon existing in parallel with...

  15. Shadow Soldiering

    DEFF Research Database (Denmark)

    Mynster Christensen, Maya

    The thesis is an inquiry into what is at stake for a surplus population of militia soldiers in the aftermaths of the civil war in Sierra Leone. The analysis takes its point of departure in how militarised networks are transformed and gradualy morph into new constellations of soldiering. The central......, or in the margins of official political economies. Rather, shadow soldiering is a phenomenon that is becoming increasingly central in the context of security outsourcing and militarisation in a global economy....

  16. Syndrome of extended shadow

    International Nuclear Information System (INIS)

    Ginzburg, M.A.

    1987-01-01

    Syndrome of extended shadow is characterized by large (more than one lobe) or total shadow of the lung area. A detailed roentgenological characteristic and intrasyndrome differential diagnosis of extended shadows is given. Ethiology, pathogenesis and pathomorphology as well as clinical picture and methods of investigation of extended shadows are discussed

  17. The little book of light and shadow

    CERN Document Server

    Thornton, Linda

    2013-01-01

    Encourage your Early Learners to becom investigators by exploring the concept of light and shadow. These simple and effective activities can be carried out independently with the focus on natural resources.

  18. MMW [multimegawatt] shielding design and analysis

    International Nuclear Information System (INIS)

    Olson, A.P.

    1988-01-01

    Reactor shielding for multimegawatt (MMW) space power must satisfy a mass constraint as well as performance specifications for neutron fluence and gamma dose. A minimum mass shield is helpful in attaining the launch mass goal for the entire vehicle, because the shield comprises about 1% to 2% of the total vehicle mass. In addition, the shield internal heating must produce tolerable temperatures. The analysis of shield performance for neutrons and gamma rays is emphasized. Topics addressed include cross section preparation for multigroup 2D S/sub n/-transport analyses, and the results of parametric design studies on shadow shield performance and mass versus key shield design variables such as cone angle, number, placement, and thickness of layers of tungsten, and shield top radius. Finally, adjoint methods are applied to the shield in order to spatially map its relative contribution to dose reduction, and to provide insight into further design optimization. 7 refs., 2 figs., 3 tabs

  19. Real-time shadows

    CERN Document Server

    Eisemann, Elmar; Assarsson, Ulf; Wimmer, Michael

    2011-01-01

    Important elements of games, movies, and other computer-generated content, shadows are crucial for enhancing realism and providing important visual cues. In recent years, there have been notable improvements in visual quality and speed, making high-quality realistic real-time shadows a reachable goal. Real-Time Shadows is a comprehensive guide to the theory and practice of real-time shadow techniques. It covers a large variety of different effects, including hard, soft, volumetric, and semi-transparent shadows.The book explains the basics as well as many advanced aspects related to the domain

  20. Shadowing and hyperbolicity

    CERN Document Server

    Pilyugin, Sergei Yu

    2017-01-01

    Focusing on the theory of shadowing of approximate trajectories (pseudotrajectories) of dynamical systems, this book surveys recent progress in establishing relations between shadowing and such basic notions from the classical theory of structural stability as hyperbolicity and transversality. Special attention is given to the study of "quantitative" shadowing properties, such as Lipschitz shadowing (it is shown that this property is equivalent to structural stability both for diffeomorphisms and smooth flows), and to the passage to robust shadowing (which is also equivalent to structural stability in the case of diffeomorphisms, while the situation becomes more complicated in the case of flows). Relations between the shadowing property of diffeomorphisms on their chain transitive sets and the hyperbolicity of such sets are also described. The book will allow young researchers in the field of dynamical systems to gain a better understanding of new ideas in the global qualitative theory. It will also be of int...

  1. Shadowing in dynamical systems

    CERN Document Server

    Pilyugin, Sergei Yu

    1999-01-01

    This book is an introduction to the theory of shadowing of approximate trajectories in dynamical systems by exact ones. This is the first book completely devoted to the theory of shadowing. It shows the importance of shadowing theory for both the qualitative theory of dynamical systems and the theory of numerical methods. Shadowing Methods allow us to estimate differences between exact and approximate solutions on infinite time intervals and to understand the influence of error terms. The book is intended for specialists in dynamical systems, for researchers and graduate students in the theory of numerical methods.

  2. Fading and shadowing in wireless systems

    CERN Document Server

    Shankar, P Mohana

    2017-01-01

    This book offers a comprehensive overview of fading and shadowing in wireless channels. A number of statistical models including simple, hybrid, compound and cascaded ones are presented along with a detailed discussion of diversity techniques employed to mitigate the effects of fading and shadowing. The effects of co-channel interference before and after the implementation of diversity are also analyzed. To facilitate easy understanding of the models and the analysis, the background on probability and random variables is presented with relevant derivations of densities of the sums, products, ratios as well as order statistics of random variables. The book also provides material on digital modems of interest in wireless systems. The updated edition expands the background materials on probability by offering sections on Laplace and Mellin transforms, parameter estimation, statistical testing and receiver operating characteristics. Newer models for fading, shadowing and shadowed fading are included along with th...

  3. How do Institutions Affect Corruption and the Shadow Economy?

    OpenAIRE

    Axel Dreher; Christos Kotsogiannis; Steve McCorriston

    2005-01-01

    This paper analyzes a simple model that captures the relationship between institutional quality, the shadow economy and corruption. It shows that an improvement in institutional quality reduces the shadow economy and affects the corruption market. The exact relationship between corruption and institutional quality is, however, ambiguous and depends on the relative effectiveness of the institutional quality in the shadow and corruption markets. The predictions of the model are empirically test...

  4. Radiation shield

    International Nuclear Information System (INIS)

    Hosoya, Yasuaki

    1993-01-01

    In the present invention, the thickness of the radiation shields is minimized to save the quantity of shields thereby utilizing spaces in a facility effectively. That is, the radiation shields of the present invention comprise first and second shields forming stepwise gaps. They are disposed between a high dose region and a low dose region. The first and second shields have a feature in that the thickness thereof can be set to a size capable of shielding the gaps in accordance with the strength of the radiation source to be shielded. With such a constitution, the thickness of the shields of the radiation processing facility can be minimized. Accordingly, the quantity of the shields can be greatly saved. Spaces in the facility can be utilized effectively. (I.S.)

  5. An Automatic Shadow Detection Method for VHR Remote Sensing Orthoimagery

    Directory of Open Access Journals (Sweden)

    Qiongjie Wang

    2017-05-01

    Full Text Available The application potential of very high resolution (VHR remote sensing imagery has been boosted by recent developments in the data acquisition and processing ability of aerial photogrammetry. However, shadows in images contribute to problems such as incomplete spectral information, lower intensity brightness, and fuzzy boundaries, which seriously affect the efficiency of the image interpretation. In this paper, to address these issues, a simple and automatic method of shadow detection is presented. The proposed method combines the advantages of the property-based and geometric-based methods to automatically detect the shadowed areas in VHR imagery. A geometric model of the scene and the solar position are used to delineate the shadowed and non-shadowed areas in the VHR image. A matting method is then applied to the image to refine the shadow mask. Different types of shadowed aerial orthoimages were used to verify the effectiveness of the proposed shadow detection method, and the results were compared with the results obtained by two state-of-the-art methods. The overall accuracy of the proposed method on the three tests was around 90%, confirming the effectiveness and robustness of the new method for detecting fine shadows, without any human input. The proposed method also performs better in detecting shadows in areas with water than the other two methods.

  6. Electromagnetic shielding

    International Nuclear Information System (INIS)

    Tzeng, Wen-Shian V.

    1991-01-01

    Electromagnetic interference (EMI) shielding materials are well known in the art in forms such as gaskets, caulking compounds, adhesives, coatings and the like for a variety of EMI shielding purposes. In the past, where high shielding performance is necessary, EMI shielding has tended to use silver particles or silver coated copper particles dispersed in a resin binder. More recently, aluminum core silver coated particles have been used to reduce costs while maintaining good electrical and physical properties. (author). 8 figs

  7. Shadow Toll in Colombia

    OpenAIRE

    González Ruiz, Juan David; Botero Botero, Sergio; Arboleda, Carlos Alejandro; Duque Grisales, Eduardo Alexander

    2015-01-01

    The growing development in infrastructure projects in Colombia has been linked to legal adjustments and capital markets. These two last factors have provided important elements for project developers to design funding strategies. Based on the shadow toll scheme, this paper proposes a new financing strategy for funding highway projects. This strategy may be implemented in Colombia. Finally, the paper proposes future research on shadow toll schemes as a financial mechanism.

  8. Shielding container

    International Nuclear Information System (INIS)

    Darling, K.A.M.

    1981-01-01

    A shielding container incorporates a dense shield, for example of depleted uranium, cast around a tubular member of curvilinear configuration for accommodating a radiation source capsule. A lining for the tubular member, in the form of a close-coiled flexible guide, provides easy replaceability to counter wear while the container is in service. Container life is extended, and maintenance costs are reduced. (author)

  9. Shadows behind the computers

    CERN Multimedia

    2007-01-01

    EGEE organized a shadowing day to spur female students to take up careers in the IT field. Eleven female staff from CERN’s IT Department were kept under close surveillance last week, shadowed by female students from the Collège du Léman International School as part of the Enabling Grids for E-sciencE project Gender Action Plan. The shadowing day was aimed at inspiring young women to think of careers in information technology, by passing on the message that careers in science are open to both men and women and can be rewarding and fun. The students were given a tour of the ATLAS physics experiment and the CERN Computer Centre, as well as the opportunity for one-to-one interaction with CERN IT staff. Traditionally, fewer women work in the IT sector; women currently represent 21% of EGEE staff. The shadowing day was held as part of the EGEE Gender Action Plan, reflecting a commitment to reducing this gender gap. Other initiatives in...

  10. Projectors, shadows, and conformal blocks

    Energy Technology Data Exchange (ETDEWEB)

    Simmons-Duffin, David [Jefferson Physical Laboratory, Harvard University,Cambridge, MA 02138 (United States)

    2014-04-24

    We introduce a method for computing conformal blocks of operators in arbitrary Lorentz representations in any spacetime dimension, making it possible to apply bootstrap techniques to operators with spin. The key idea is to implement the “shadow formalism' of Ferrara, Gatto, Grillo, and Parisi in a setting where conformal invariance is manifest. Conformal blocks in d-dimensions can be expressed as integrals over the projective null-cone in the “embedding space' ℝ{sup d+1,1}. Taking care with their analytic structure, these integrals can be evaluated in great generality, reducing the computation of conformal blocks to a bookkeeping exercise. To facilitate calculations in four-dimensional CFTs, we introduce techniques for writing down conformally-invariant correlators using auxiliary twistor variables, and demonstrate their use in some simple examples.

  11. Shielding Effectiveness of Laminated Shields

    Directory of Open Access Journals (Sweden)

    B. P. Rao

    2008-12-01

    Full Text Available Shielding prevents coupling of undesired radiated electromagnetic energy into equipment otherwise susceptible to it. In view of this, some studies on shielding effectiveness of laminated shields with conductors and conductive polymers using plane-wave theory are carried out in this paper. The plane wave shielding effectiveness of new combination of these materials is evaluated as a function of frequency and thickness of material. Conductivity of the polymers, measured in previous investigations by the cavity perturbation technique, is used to compute the overall reflection and transmission coefficients of single and multiple layers of the polymers. With recent advances in synthesizing stable highly conductive polymers these lightweight mechanically strong materials appear to be viable alternatives to metals for EM1 shielding.

  12. REACTOR SHIELD

    Science.gov (United States)

    Wigner, E.P.; Ohlinger, L.E.; Young, G.J.; Weinberg, A.M.

    1959-02-17

    Radiation shield construction is described for a nuclear reactor. The shield is comprised of a plurality of steel plates arranged in parallel spaced relationship within a peripheral shell. Reactor coolant inlet tubes extend at right angles through the plates and baffles are arranged between the plates at right angles thereto and extend between the tubes to create a series of zigzag channels between the plates for the circulation of coolant fluid through the shield. The shield may be divided into two main sections; an inner section adjacent the reactor container and an outer section spaced therefrom. Coolant through the first section may be circulated at a faster rate than coolant circulated through the outer section since the area closest to the reactor container is at a higher temperature and is more radioactive. The two sections may have separate cooling systems to prevent the coolant in the outer section from mixing with the more contaminated coolant in the inner section.

  13. Nuclear shields

    International Nuclear Information System (INIS)

    Linares, R.C.; Nienart, L.F.; Toelcke, G.A.

    1976-01-01

    A process is described for preparing melt-processable nuclear shielding compositions from chloro-fluoro substituted ethylene polymers, particularly PCTFE and E-CTFE, containing 1 to 75 percent by weight of a gadolinium compound. 13 claims, no drawings

  14. Rhetorical shadows : The conceptual representation of incongruent shadows

    NARCIS (Netherlands)

    Schilperoord, J; van Weelden, L.|info:eu-repo/dai/nl/362752877

    2018-01-01

    This article addresses the topic of conceptual representation of shadows. We analyze several examples of contemporary imagery, taken from advertising and cartooning, to shed light on the way shadow depictions are used as rhetorical devices. Instead of being inserted as a natural phenomenon,

  15. Induced Radioactivity in Lead Shielding at the National Synchrotron Light Source.

    Science.gov (United States)

    Ghosh, Vinita J; Schaefer, Charles; Kahnhauser, Henry

    2017-06-01

    The National Synchrotron Light Source (NSLS) at Brookhaven National Laboratory was shut down in September 2014. Lead bricks used as radiological shadow shielding within the accelerator were exposed to stray radiation fields during normal operations. The FLUKA code, a fully integrated Monte Carlo simulation package for the interaction and transport of particles and nuclei in matter, was used to estimate induced radioactivity in this shielding and stainless steel beam pipe from known beam losses. The FLUKA output was processed using MICROSHIELD® to estimate on-contact exposure rates with individually exposed bricks to help design and optimize the radiological survey process. This entire process can be modeled using FLUKA, but use of MICROSHIELD® as a secondary method was chosen because of the project's resource constraints. Due to the compressed schedule and lack of shielding configuration data, simple FLUKA models were developed. FLUKA activity estimates for stainless steel were compared with sampling data to validate results, which show that simple FLUKA models and irradiation geometries can be used to predict radioactivity inventories accurately in exposed materials. During decommissioning 0.1% of the lead bricks were found to have measurable levels of induced radioactivity. Post-processing with MICROSHIELD® provides an acceptable secondary method of estimating residual exposure rates.

  16. Drip Shield Emplacement Gantry Concept

    International Nuclear Information System (INIS)

    Silva, R.A.; Cron, J.

    2000-01-01

    This design analysis has shown that, on a conceptual level, the emplacement of drip shields is feasible with current technology and equipment. A plan for drip shield emplacement was presented using a Drip Shield Transporter, a Drip Shield Emplacement Gantry, a locomotive, and a Drip Shield Gantry Carrier. The use of a Drip Shield Emplacement Gantry as an emplacement concept results in a system that is simple, reliable, and interfaces with the numerous other exising repository systems. Using the Waste Emplacement/Retrieval System design as a basis for the drip shield emplacement concept proved to simplify the system by using existing equipment, such as the gantry carrier, locomotive, Electrical and Control systems, and many other systems, structures, and components. Restricted working envelopes for the Drip Shield Emplacement System require further consideration and must be addressed to show that the emplacement operations can be performed as the repository design evolves. Section 6.1 describes how the Drip Shield Emplacement System may use existing equipment. Depending on the length of time between the conclusion of waste emplacement and the commencement of drip shield emplacement, this equipment could include the locomotives, the gantry carrier, and the electrical, control, and rail systems. If the exisiting equipment is selected for use in the Drip Shield Emplacement System, then the length of time after the final stages of waste emplacement and start of drip shield emplacement may pose a concern for the life cycle of the system (e.g., reliability, maintainability, availability, etc.). Further investigation should be performed to consider the use of existing equipment for drip shield emplacement operations. Further investigation will also be needed regarding the interfaces and heat transfer and thermal effects aspects. The conceptual design also requires further design development. Although the findings of this analysis are accurate for the assumptions made

  17. Is shadow banking really banking?

    OpenAIRE

    Bryan J. Noeth; Rajdeep Sengupta

    2011-01-01

    To those who don't know, the term "shadow banking" probably has a negative connotation. This primer draws parallels between what has been termed the shadow banking sector and the traditional banking sector—showing that they are similar in many ways.

  18. Shielding effect of a thick screen with corrugations

    OpenAIRE

    Albani, M; Piazzesi, P; Capolino, F; Maci, S; Tiberio, R

    1998-01-01

    The shielding effectiveness of a corrugated thick screen is theoretically and experimentally investigated. This screen consists of a half-plane of finite thickness in which corrugations are etched on the smaller side. This structure provides a significant attenuation in the shadow region for both polarizations of the incident field; thus, it can be effectively used for protecting apparatuses from radiating interference as well as for decoupling nearby operating antennas. The shielding propert...

  19. The Moon's Phases and the Self Shadow

    Science.gov (United States)

    Young, Timothy; Guy, Mark

    2008-01-01

    In this article, the authors present a new way of teaching the phases of the Moon. Through the introduction of a "self shadow" (an idea of a shadow that is not well-known), they illuminate students' understanding of the phases of the Moon and help them understand the distinction between the shadows that cause eclipses and the shadows that relate…

  20. Out of shadow / Peeter Linnap

    Index Scriptorium Estoniae

    Linnap, Peeter, 1960-

    2007-01-01

    "Out of shadow" oli näitus Baltimaade 1990. aastate kunstist Ameerika publikule - sõnumiks iseseisvumisjärgsete aastate materiaalse, sotsiaalse ning vaimuelu peegeldused/tõlgendused visuaalses kunstis

  1. Gonad Shielding for Patients Undergoing Conventional Radiological Examinations: Is There Cause for Concern?

    Directory of Open Access Journals (Sweden)

    Karami

    2016-04-01

    Full Text Available Background Gonad shielding is one of the fundamental methods by which to protect reproductive organs in patients undergoing conventional radiological examinations. A lack of or inadequate shielding of the gonads may increase the exposure of these organs and result in malignancies future generations. Objectives The aim of this study is to investigate the prevalence of gonad shielding in patients undergoing conventional radiological examinations and the availability of gonad shields and gonad shielding protocols in radiology departments. Materials and Methods A retrospective, observational cross-sectional study on the application of gonad shielding, the availability of gonad shields and the existence of gonad shielding protocols in radiology departments was performed in five different hospitals in Ahvaz, Iran. Results The highest application of gonad shielding was 6.6% for the pediatric hospital. The prevalence of gonad shielding was less than 0.2%. In 64.3% of the radiography rooms, at least one flat-contact gonad shield of a large size was available. Only large-sized gonad shields were available. Curved-contact and shadow gonad shields did not exist. Gonad shielding protocols were not existence in any of the fourteen radiography rooms investigated. Conclusions Comprehensive protection programs with on-the-job training courses for staff members are strongly recommended, as well as, the provision of radiological shields and gonad shielding protocols in radiology departments to reduce the patient’s radiation dose during radiological examinations.

  2. Unitarity bound for gluon shadowing

    International Nuclear Information System (INIS)

    Kopeliovich, B. Z.; Levin, E.; Potashnikova, I. K.; Schmidt, Ivan

    2009-01-01

    Although at small Bjorken x gluons originated from different nucleons in a nucleus overlap in the longitudinal direction, most of them are still well separated in the transverse plane and therefore cannot fuse. For this reason the gluon density in nuclei cannot drop at small x below a certain bottom bound, which we evaluated in a model independent manner assuming the maximal strength of gluon fusion. We also calculated gluon shadowing in the saturated regime using the Balitsky-Kovchegov equation and found the nuclear ratio to be well above the unitarity bound. The recently updated analysis of parton distributions in nuclei, including BNL Relativistic Heavy Ion Collider (RHIC) data on high-p T hadron production at forward rapidities, led to strong gluon shadowing. Such strong shadowing and therefore the interpretation of the nuclear modification of the p T spectra in dA collisions at RHIC seem to be inconsistent with this unitarity bound.

  3. About the Scythian Shields

    Directory of Open Access Journals (Sweden)

    About the Scythian Shields

    2017-10-01

    Full Text Available Shields played major role in the armament system of the Scythians. Made from organic materials, they are poorly traced on the materials of archaeological excavations. Besides, scaly surface of shields was often perceived in practice as the remnants of the scaly armor. E. V. Chernenko was able to discern the difference between shields’ scaly plates and armor scales. The top edge of the scales was bent inwards, and shield plates had a wire fixation. These observations let significantly increase the number of shields, found in the burial complexes of the Scythians. The comparison of archaeological materials and the images of Scythian warriors allow distinguishing the main forms of Scythian shields. All shields are divided into fencing shields and cover shields. The fencing shields include round wooden shields, reinforced with bronze sheet, and round moon-shaped shields with a notch at the top, with a metal scaly surface. They came to the Scythians under the Greek influence and are known in the monuments of the 4th century BC. Oval shields with scaly surface (back cover shields were used by the Scythian cavalry. They protected the rider in case of frontal attack, and moved back in case of maneuver or closein fighting. Scythian battle tactics were based on rapid approaching the enemy and throwing spears and further rapid withdrawal. Spears stuck in the shields of enemies, forcing them to drop the shields, uncover, and in this stage of the battle the archers attacked the disorganized ranks of the enemy. That was followed by the stage of close fight. Oval form of a wooden shield with leather covering was used by the Scythian infantry and spearmen. Rectangular shields, including wooden shields and the shields pleached from rods, represented a special category. The top of such shield was made of wood, and a pleached pad on leather basis was attached to it. This shield could be a reliable protection from arrows, but it could not protect against javelins

  4. Innocent Body-Shadow Mimics Physical Body

    Directory of Open Access Journals (Sweden)

    Kenri Kodaka

    2017-04-01

    Full Text Available The paradigm of the rubber hand illusion was applied to a shadow to determine whether the body-shadow is a good candidate for the alternative belonging to our body. Three kinds of shadows, a physical hand, a hand-shaped cloth, and a rectangle cloth, were tested for this purpose. The questionnaire results showed that both anatomical similarity and visuo-proprioception correlation were effective in enhancing illusory ownership of the shadow. According to the proprioceptive drift measurement, whether the shadow purely originated from the physical body was a critical factor in yielding the significantly positive drift. Thus, results demonstrated that the shadow can distort illusory ownership with the rubber hand illusion paradigm, but the proprioception was clearly distorted only when the body-shadow was purely applied. This implies the presence of special cognitive processing to discriminate the self-body shadow from the others.

  5. Study on Processing Method of Image Shadow

    Directory of Open Access Journals (Sweden)

    Wang Bo

    2014-07-01

    Full Text Available In order to effectively remove disturbance of shadow and enhance robustness of information processing of computer visual image, this paper makes study on inspection and removal of image shadow. It makes study the continual removal algorithm of shadow based on integration, the illumination surface and texture, it respectively introduces their work principles and realization method, it can effectively carrying processing for shadow by test.

  6. Radiation shielding device

    International Nuclear Information System (INIS)

    Nakagawa, Takahiro; Yamagami, Makoto.

    1996-01-01

    A fixed shielding member made of a radiation shielding material is constituted in perpendicular to an opening formed on radiation shielding walls. The fixed shielding member has one side opened and has other side, the upper portion and the lower portion disposed in close contact with the radiation shielding walls. Movable shielding members made of a radiation shielding material are each disposed openably on both side of the fixed shielding member. The movable shielding member has a shaft as a fulcrum on one side thereof for connecting it to the radiation shielding walls. The other side has a handle attached for opening/closing the movable shielding member. Upon access of an operator, when each one of the movable shielding members is opened/closed on every time, leakage of linear or scattered radiation can be prevented. Even when both of the movable shielding members are opened simultaneously, the fixed shielding member and the movable shielding members form labyrinth to prevent leakage of linear radioactivity. (I.N.)

  7. Creating cloud-free Landsat ETM+ data sets in tropical landscapes: cloud and cloud-shadow removal

    Science.gov (United States)

    Sebastián Martinuzzi; William A. Gould; Olga M. Ramos Gonzalez

    2007-01-01

    Clouds and cloud shadows are common features of visible and infrared remotelysensed images collected from many parts of the world, particularly in humid and tropical regions. We have developed a simple and semiautomated method to mask clouds and shadows in Landsat ETM+ imagery, and have developed a recent cloud-free composite of multitemporal images for Puerto Rico and...

  8. Radiation shielding design considerations for Doublet III

    International Nuclear Information System (INIS)

    Engholm, B.A.

    1980-06-01

    Calculations and measurements were made of the bremsstrahlung (x-ray) doses resulting from runaway electron shots at Doublet III. The analysis considered direct, wall-scattered, and skyshine contributions. Reasonably good agreement was obtained between calculations and measurements. The x-ray dose in the control room was about 1 mR per runaway shot, while that at the north boundary was undetectable, with a calculated value of 0.05 mR per shot. These low doses attest to the adequacy of the 2 ft concrete shadow shield surrounding the Doublet III room. Exploratory shielding analyses were performed for possible neutron generation if Doublet III were operated with neutral beam injection in an aggressive D-D mode

  9. Diffractive production off nuclei-shadow of hadronic bremsstrahlung

    International Nuclear Information System (INIS)

    Bialas, A.; Czyz, W.

    1974-01-01

    Diffractive production on nuclei is calculated using as an input a specific model for diffractive production on nucleons. In this model diffractive production is described as a shadow of non-diffractive multiple production of particles. The mechanism for non-diffractive production is taken to be hadronic bremsstrahlung of independently produced clusters. It is shown that such a model naturally explains the strikingly simple pattern of absorption observed in coherent production on nuclei. Possible generalizations of these results are indicated. (author)

  10. Design of emergency shield

    International Nuclear Information System (INIS)

    Soliman, S.E.

    1993-01-01

    Manufacturing of an emergency movable shield in the hot laboratories center is urgently needed for the safety of personnel in case of accidents or spilling of radioactive materials. In this report, a full design for an emergency shield is presented and the corresponding dose rates behind the shield for different activities (from 1 mCi to 5 Ci) was calculated by using micro shield computer code. 4 figs., 1 tab

  11. Electromagnetically shielded building

    International Nuclear Information System (INIS)

    Takahashi, T.; Nakamura, M.; Yabana, Y.; Ishikawa, T.; Nagata, K.

    1992-01-01

    This invention relates to a building having an electromagnetic shield structure well-suited for application to an information network system utilizing electromagnetic waves, and more particularly to an electromagnetically shielded building for enhancing the electromagnetic shielding performance of an external wall. 6 figs

  12. Shadow imaging of geosynchronous satellites

    Science.gov (United States)

    Douglas, Dennis Michael

    Geosynchronous (GEO) satellites are essential for modern communication networks. If communication to a GEO satellite is lost and a malfunction occurs upon orbit insertion such as a solar panel not deploying there is no direct way to observe it from Earth. Due to the GEO orbit distance of ~36,000 km from Earth's surface, the Rayleigh criteria dictates that a 14 m telescope is required to conventionally image a satellite with spatial resolution down to 1 m using visible light. Furthermore, a telescope larger than 30 m is required under ideal conditions to obtain spatial resolution down to 0.4 m. This dissertation evaluates a method for obtaining high spatial resolution images of GEO satellites from an Earth based system by measuring the irradiance distribution on the ground resulting from the occultation of the satellite passing in front of a star. The representative size of a GEO satellite combined with the orbital distance results in the ground shadow being consistent with a Fresnel diffraction pattern when observed at visible wavelengths. A measurement of the ground shadow irradiance is used as an amplitude constraint in a Gerchberg-Saxton phase retrieval algorithm that produces a reconstruction of the satellite's 2D transmission function which is analogous to a reverse contrast image of the satellite. The advantage of shadow imaging is that a terrestrial based redundant set of linearly distributed inexpensive small telescopes, each coupled to high speed detectors, is a more effective resolved imaging system for GEO satellites than a very large telescope under ideal conditions. Modeling and simulation efforts indicate sub-meter spatial resolution can be readily achieved using collection apertures of less than 1 meter in diameter. A mathematical basis is established for the treatment of the physical phenomena involved in the shadow imaging process. This includes the source star brightness and angular extent, and the diffraction of starlight from the satellite

  13. Shielding benchmark problems, (2)

    International Nuclear Information System (INIS)

    Tanaka, Shun-ichi; Sasamoto, Nobuo; Oka, Yoshiaki; Shin, Kazuo; Tada, Keiko.

    1980-02-01

    Shielding benchmark problems prepared by Working Group of Assessment of Shielding Experiments in the Research Committee on Shielding Design in the Atomic Energy Society of Japan were compiled by Shielding Laboratory in Japan Atomic Energy Research Institute. Fourteen shielding benchmark problems are presented newly in addition to twenty-one problems proposed already, for evaluating the calculational algorithm and accuracy of computer codes based on discrete ordinates method and Monte Carlo method and for evaluating the nuclear data used in codes. The present benchmark problems are principally for investigating the backscattering and the streaming of neutrons and gamma rays in two- and three-dimensional configurations. (author)

  14. Determination of the shielding factors for gamma-ray spectrometers

    International Nuclear Information System (INIS)

    Korun, M.; Vodenik, B.; Zorko, B.

    2014-01-01

    A method for determining the shielding factors for gamma-ray spectrometers is described. The shielding factors are expressed by decomposing the peaked background of the spectrometer into contributions of the detector, spectrometer shield and ambient radiation to the spectrometer background. The dimensions of the sample and its mass-attenuation coefficient are taken into account using a simple model. For six spectrometers, with contributions to the background quantified, the shielding factors were determined for the background based on the thorium decay series and the radon daughters. For a water sample with a diameter of 9 cm and a thickness of 4 cm and the nuclides of the thorium decay series that are in the spectrometer shields, the values of the shielding factors lie in the interval 0.95–1.00. For a spectrometer exhibiting the diffusion of radon into the shielding material, the values of the shielding factors for the same sample for gamma-rays from the radon daughters lie in the interval 0.88–1.00. - Highlights: • A model is described to assess shielding factors for gamma-ray spectrometers. • The background due to the detector, shield and ambient radiation must be known. • The sample attenuation, its dimensions and distance from the crystal are considered. • Shielding factors for gamma-rays from the 232 Th and 226 Ra decay chains are assessed. • For a water sample with a mass of 0.25 kg, shielding factors above 0.88 are obtained

  15. Chromatic Shadow Detection and Tracking for Moving Foreground Segmentation

    DEFF Research Database (Denmark)

    Huerta, Ivan; Holte, Michael Boelstoft; Moeslund, Thomas B.

    2015-01-01

    Advanced segmentation techniques in the surveillance domain deal with shadows to avoid distortions when detecting moving objects. Most approaches for shadow detection are still typically restricted to penumbra shadows and cannot cope well with umbra shadows. Consequently, umbra shadow regions are...

  16. Moving Shadow Detection in Video Using Cepstrum

    Directory of Open Access Journals (Sweden)

    Fuat Cogun

    2013-01-01

    Full Text Available Moving shadows constitute problems in various applications such as image segmentation and object tracking. The main cause of these problems is the misclassification of the shadow pixels as target pixels. Therefore, the use of an accurate and reliable shadow detection method is essential to realize intelligent video processing applications. In this paper, a cepstrum-based method for moving shadow detection is presented. The proposed method is tested on outdoor and indoor video sequences using well-known benchmark test sets. To show the improvements over previous approaches, quantitative metrics are introduced and comparisons based on these metrics are made.

  17. Giant atoms cast long shadow

    International Nuclear Information System (INIS)

    Amato, I.

    1996-01-01

    Atoms swollen with energy can serve as supersensitive detectors. They also probe the shadow realm where the quantum world of the atom gives way to the familiar classical world. Created in the laboratory, where they live for a few milliseconds inside vacuum chambers, Rydberg atoms acquire their girth when one or sometimes two of their electrons are excited to very high energy levels, displacing them far from the nuclear core. This article describes the atoms, the history of their identification, and future possibilities. 2 figs

  18. Shadows Along the Spiritual Pathway.

    Science.gov (United States)

    Humphrey, Caroline

    2015-12-01

    Contemporary spirituality discourses tend to assume that a canopy of light and love overarches all spiritual pathways. Unfortunately, the dark side of humanity cannot be spirited away so easily, and aberrations of personal spiritual development, interpersonal spiritual relationships and new spiritual movements can often be traced to the denial, repression and return of our dark side. Transpersonal psychology offers a way of approaching, reframing and redeeming the unconscious depths of our psyche, with its metaphors of shadows and daimons on the one hand, and its therapeutic practices for symbolically containing and transcending polarities on the other. In its absence, any spirituality which eulogises holistic growth is likely to engender the reverse effect.

  19. Projectors, Shadows, and Conformal Blocks

    OpenAIRE

    Simmons-Duffin, David

    2012-01-01

    We introduce a method for computing conformal blocks of operators in arbitrary Lorentz representations in any spacetime dimension, making it possible to apply bootstrap techniques to operators with spin. The key idea is to implement the “shadow formalism” of Ferrara, Gatto, Grillo, and Parisi in a setting where conformal invariance is manifest. Conformal blocks in d -dimensions can be expressed as integrals over the projective null-cone in the “embedding space” $ \\mathbb{R} $ d +1,1 . Taking ...

  20. Orientation with a Viking sun-compass, a shadow-stick, and two calcite sunstones under various weather conditions.

    Science.gov (United States)

    Bernáth, Balázs; Blahó, Miklós; Egri, Adám; Barta, András; Kriska, György; Horváth, Gábor

    2013-09-01

    It is widely accepted that Vikings used sun-compasses to derive true directions from the cast shadow of a gnomon. It has been hypothesized that when a cast shadow was not formed, Viking navigators relied on crude skylight polarimetry with the aid of dichroic or birefringent crystals, called "sunstones." We demonstrate here that a simple tool, that we call "shadow-stick," could have allowed orientation by a sun-compass with satisfying accuracy when shadows were not formed, but the sun position could have reliably been estimated. In field tests, we performed orientation trials with a set composed of a sun-compass, two calcite sunstones, and a shadow-stick. We show here that such a set could have been an effective orientation tool for Vikings only when clear, blue patches of the sky were visible.

  1. Detection of Cast Shadows in Surveillance Applications

    DEFF Research Database (Denmark)

    Erbou, Søren G.; Sørensen, Helge Bjarne Dissing; Stage, Bjarne

    2005-01-01

    Cast shadows from moving objects reduce the general ability of robust classification and tracking of these objects, in outdoor surveillance applications. A method for segmentation of cast shadows is proposed, combining statistical features with a new similarity feature, derived from a physics...

  2. Self-shielding factors

    International Nuclear Information System (INIS)

    Kaul, D.C.

    1982-01-01

    Throughout the last two decades many efforts have been made to estimate the effect of body self-shielding on organ doses from externally incident neutrons and gamma rays. These began with the use of simple geometry phantoms and have culminated in the use of detailed anthropomorphic phantoms. In a recent effort, adjoint Monte Carlo analysis techniques have been used to determine dose and dose equivalent to the active marrow as a function of energy and angle of neutron fluence externally incident on an anthropomorphic phantom. When combined with fluences from actual nuclear devices, these dose-to-fluence factors result in marrow dose values that demonstrate great sensitivity to variations in device type, range, and body orientation. Under a state-of-the-art radiation transport analysis demonstration program for the Japanese cities, sponsored by the Defense Nuclear Agency at the request of the National Council on Radiation Protection and Measurements, the marrow dose study referred to above is being repeated to obtain spectral distributions within the marrow for externally incident neutrons and gamma rays of arbitrary energy and angle. This is intended to allow radiobiologists and epidemiologists to select and to modify numbers of merit for correlation with health effects and to permit a greater understanding of the relationship between human and laboratory subject dosimetry

  3. Direct solar wind proton access into permanently shadowed lunar polar craters

    Science.gov (United States)

    Zimmerman, M. I.; Farrell, W. M.; Stubbs, T. J.; Halekas, J. S.

    2011-12-01

    Recent analyses of Lunar Prospector neutron spectrometer (LPNS) data have suggested that high abundances of hydrogen exist within cold traps at the lunar poles, and it has often been assumed that hydrogen-bearing volatiles sequestered in permanent shadow are topographically shielded from sputtering by solar wind protons. However, recent simulation results are presented showing that textbf{solar wind protons clearly access the floor of an idealized, shadowed lunar crater} through a combination of thermal and ambipolar processes, in effect creating a plasma "mini-wake". These simulations are the first to model the mini-wake environment in two spatial dimensions with a self-consistent lunar surface-plasma interaction. Progress is reported on constraining the nonzero particle fluxes and energies incident on kilometer-scale shadowed topography, such as a small crater embedded within a larger one. The importance of direct solar wind proton bombardment is discussed within the context of understanding the stability and inventory of hydrogen-bearing volatiles in shadow at the lunar poles. textit{The support of the National Lunar Science Institute, the DREAM Institute, LPROPS, and the NASA Postdoctoral Program at NASA Goddard Space Flight Center administered by ORAU are gratefully acknowledged.}

  4. Direct Solar Wind Proton Access into Permanently Shadowed Lunar Polar Craters

    Science.gov (United States)

    Zimmerman, M. I.; Farrell, W. M.; Stubbs, T. J.; Halekas, J. S.

    2011-01-01

    Recent analyses of Lunar Prospector neutron spectrometer (LPNS) data have suggested that high abundances of hydrogen exist within cold traps at the lunar poles, and it has often been assumed that hydrogen-bearing volatiles sequestered in permanent shadow are topographically shielded from sputtering by solar wind protons. However, recent simulation results are presented showing that solar wind protons clearly access the floor of an idealized, shadowed lunar crater through a combination of thermal and ambipolar processes, in effect creating a plasma "miniwake". These simulations are the first to model the mini-wake environment in two spatial dimensions with a self-consistent lunar surface-plasma interaction. Progress is reported on constraining the nonzero particle fluxes and energies incident on kilometer-scale shadowed topography, such as a small crater embedded within a larger one. The importance of direct solar wind proton bombardment is discussed within the context of understanding the stability and inventory of hydrogen-bearing volatiles in shadow at the lunar poles. The support of the National Lunar Science institute, the DREAM institute, LPROPS, and the NASA Postdoctoral Program at NASA Goddard Space Flight Center administered by ORAU are gratefully acknowledged.

  5. Thermal shielding walls

    International Nuclear Information System (INIS)

    Fujii, Takenori.

    1980-01-01

    Purpose: To suppress the amount of heat released from a pressure vessel and reliably shield neutron fluxes and gamma rays from a reactor core by the addition of cooling ducts in a thermal shielding wall provided with a blower and an air cooling cooler. Constitution: A thermal shielding wall is located on a pedestal so as to surround a pressure vessel and the pressure vessel is located by way of a skirt in the same manner. Heat insulators are disposed between the pressure vessel and the shielding wall while closer to the skirt in the skirt portion and closer to the shielding wall in the vessel body portion. A plurality of cooling ducts are arranged side by side at the inner side in the shielding wall. A through-duct radially passing through the wall is provided in the lower portion thereof and a blower fan for cooling air and a cooler for cooling returned air are connected by way of a communication duct to the other end of the through-duct. This enables to provide a shielding wall capable of suppressing the amount of heat released from the pressure vessel as much as possible and giving more effective cooling. (Kawakami, Y.)

  6. Gaining Control of Iraq's Shadow Economy

    National Research Council Canada - National Science Library

    Ramirez, David S

    2007-01-01

    .... These conditions fuel a sprawling, decades-old shadow economy manipulated by elements of organized crime, militias, and insurgents to fund attacks on Coalition forces, infrastructure and innocent Iraqi civilians...

  7. Gaining Control of Iraq's Shadow Economy

    National Research Council Canada - National Science Library

    Ramirez, David S

    2007-01-01

    .... The shadow economy is also used extensively by the poor and women for subsistence living. The combined effect for Iraqi citizens is they have to survive in a country without adequate institutions and poor governance...

  8. Shielding high energy accelerators

    CERN Document Server

    Stevenson, Graham Roger

    2001-01-01

    After introducing the subject of shielding high energy accelerators, point source, line-of-sight models, and in particular the Moyer model. are discussed. Their use in the shielding of proton and electron accelerators is demonstrated and their limitations noted. especially in relation to shielding in the forward direction provided by large, flat walls. The limitations of reducing problems to those using it cylindrical geometry description are stressed. Finally the use of different estimators for predicting dose is discussed. It is suggested that dose calculated from track-length estimators will generally give the most satisfactory estimate. (9 refs).

  9. Shadow photography method for beam emittance measurement

    International Nuclear Information System (INIS)

    Kashkovskij, V.V.; Lisin, V.A.

    1988-01-01

    Improved technique of shadow photography which allows to measure rather simply and accurately the angular distribution of electrons extracted from betatron is described. Measurement accuracy of particle flight angles is determined by setting of rods relatively to the plane of photographic paper sheet, their diameter and shadow trace length. Incidental angle deviation of rod axes contributes mainly into the error. Mean root-square error constituted 2-3% according to the results of several measurements of angles

  10. Location Verification Systems Under Spatially Correlated Shadowing

    OpenAIRE

    Yan, Shihao; Nevat, Ido; Peters, Gareth W.; Malaney, Robert

    2014-01-01

    The verification of the location information utilized in wireless communication networks is a subject of growing importance. In this work we formally analyze, for the first time, the performance of a wireless Location Verification System (LVS) under the realistic setting of spatially correlated shadowing. Our analysis illustrates that anticipated levels of correlated shadowing can lead to a dramatic performance improvement of a Received Signal Strength (RSS)-based LVS. We also analyze the per...

  11. Investigation of the Stability via Shadowing Property

    Directory of Open Access Journals (Sweden)

    Koh Heejeong

    2009-01-01

    Full Text Available The shadowing property is to find an exact solution to an iterated map that remains close to an approximate solution. In this article, using shadowing property, we show the stability of the following equation in normed group: , where , and is a mapping. And we prove that the even mapping which satisfies the above equation is quadratic and also the Hyers-Ulam stability of the functional equation in Banach spaces.

  12. Evaluation of Digital Shadow Economy Prevention Measures

    Directory of Open Access Journals (Sweden)

    Remeikiene Rita

    2016-06-01

    Full Text Available Although during the past few years the scopes of shadow economy in Lithuania have slightly decreased, different forms of this phenomenon, in particular digital shadow activities, still generate a significant part of the overall value added. As no constant estimations of the scope of digital shadow economy have been made in Lithuania, alleviation of this problem is based on consequence fighting rather than reason elimination. Digital shadow economy poses a significant challenge for law enforcement agencies concerning its investigation and prevention. Hence, it is purposeful to research both theoretical and practical aspects of digital shadow economy prevention in order to identify the measures that could be used for the efficient reduction of the scope of this phenomenon. The aim of this research is to identify the measures of digital shadow economy prevention and compare the attitudes of governmental institutions and consumers towards the efficiency of these measures. The results of the empirical research showed that both consumers and experts agree that the level of tax morale has to be raised not only by using the measures of self-education but also by introducing long-term educational programmes; second, public authorities should ensure business friendly environment, actively implement the principles of justice and officially acknowledge and announce the concept of digital shadow economy; finally, for more efficient detection of the cases of digital shadow activities, it is necessary to reinforce current labour resources that should be specially trained to be able to disclose revenue hiding and tax evasion schemes, employed in e-trade.

  13. Exposing photo manipulation using geometry and shadows

    Science.gov (United States)

    Zheng, Jiangbin; Song, Xuemei; Ren, Jinchang; Zhu, Tingge

    2014-04-01

    It is increasingly easier to manipulate digital images by the sophisticated photo editing software. Often visual inspection cannot definitively distinguish manipulation from authentic images. This paper introduces a forensic technique that focuses on geometric and shadow color inconsistencies which arise when fake objects with shadows are inserted into an image or an object with its shadow in the image are modified. This paper analyzes three underlying geometric relations and shadow color characteristic constrains that occur in image scene. In particular, (i) explore the property of vanishing point in linear perspective project, and evaluate the geometric consistent level of the image based on the uncertain degree of vanishing point;(ii) analyze the relation between illuminated object and its cast shadow which are modeled by the planar homology and use this constrain to estimate the image's geometric consistent level;(iii) locate tempered region by measure the K-L divergence between shadow pairs. Visually plausible forgery images demonstrate the performance of our proposed method.

  14. The shadow response of the cockroach periplaneta americana.

    Science.gov (United States)

    Meyer, D J; Margiotta, J F; Walcott, B

    1981-01-01

    We show that the "escape response" (running) of the cockroach Periplaneta americana is interrupted when the insect runs through a shadow. Shadows were cast by holding an opaque plastic sheet so that the cockroach ran beneath it. In control experiments, a similarly positioned clear plastic sheet was ineffective. Removal of the shadow stimulus allowed running to continue. The likelihood that cockroaches would resume running after removal of the shadow stimulus decreased with the time they were allowed to remain in shadow.

  15. Scintillation counter, segmented shield

    International Nuclear Information System (INIS)

    Olson, R.E.; Thumim, A.D.

    1975-01-01

    A scintillation counter, particularly for counting gamma ray photons, includes a massive lead radiation shield surrounding a sample-receiving zone. The shield is disassembleable into a plurality of segments to allow facile installation and removal of a photomultiplier tube assembly, the segments being so constructed as to prevent straight-line access of external radiation through the shield into radiation-responsive areas. Provisions are made for accurately aligning the photomultiplier tube with respect to one or more sample-transmitting bores extending through the shield to the sample receiving zone. A sample elevator, used in transporting samples into the zone, is designed to provide a maximum gamma-receiving aspect to maximize the gamma detecting efficiency. (U.S.)

  16. Adhesive particle shielding

    Science.gov (United States)

    Klebanoff, Leonard Elliott [Dublin, CA; Rader, Daniel John [Albuquerque, NM; Walton, Christopher [Berkeley, CA; Folta, James [Livermore, CA

    2009-01-06

    An efficient device for capturing fast moving particles has an adhesive particle shield that includes (i) a mounting panel and (ii) a film that is attached to the mounting panel wherein the outer surface of the film has an adhesive coating disposed thereon to capture particles contacting the outer surface. The shield can be employed to maintain a substantially particle free environment such as in photolithographic systems having critical surfaces, such as wafers, masks, and optics and in the tools used to make these components, that are sensitive to particle contamination. The shield can be portable to be positioned in hard-to-reach areas of a photolithography machine. The adhesive particle shield can incorporate cooling means to attract particles via the thermophoresis effect.

  17. Grounding, shielding, and bonding

    Science.gov (United States)

    Catrysse, J.

    1991-06-01

    In the electromagnetic compatibility design (EMC) of systems and circuits, both grounding and shielding are related to the coupling mechanisms of the system with (radiated) electromagnetic fields. Grounding is more related to the source or victim circuit (or system) and determines the characteristic of the coupling mechanism between fields and currents/voltages. Shielding is a way of interacting in the radiation path of an electromagnetic field. The basic principles and practical design rules are discussed.

  18. Radiation shielding member

    International Nuclear Information System (INIS)

    Mizuochi, Akira; Narita, Takuya; Omori, Tetsu; Nemezawa, Isao; Kimura, Kunihiro.

    1997-01-01

    A radiation shielding member comprising a lead plate or a lead fabrication product is covered integrally with a rubber, a synthetic resin or a flame retardant fabric having a thickness greater than that of an oxidation preventive membrane made of a copper material. Radiation rays are shielded by the lead material, and not only oxidation but also failure of the lead material and generation of lead pieces or powder can be prevented by the coating of the rubber, the synthetic resin or the flame retardant fabric. The shape of the radiation shielding member can be conformed to constitutional products, a reinforcing frame or plate is formed integrally with the radiation shielding plate, alternatively, lowering of strength of the structure by fabrication of the shape is reinforced by the reinforcing frame or plate. The radiation shielding member is suspended by hanging a rope on a grommet, or disposed on constitutional products, or adjacent radiation shielding members are combined with each other by fixing metals. The thickness of the coating made of rubber, synthetic rubber or flame retardant fabric is determined to 0.1mm or greater to prevent failures of the lead material or formation of lead powder. (N.H.)

  19. Development of the shadow banking system in Zimbabwe: A blessing from the shadows?

    Directory of Open Access Journals (Sweden)

    Misheck Mutize

    2015-10-01

    Full Text Available The rising of shadow banking institutions in Zimbabwe has been very quick for formal banking institutions and regulators to strategise against the threats that came with their development. This study applied qualitative data analysis and find that, the growth of a shadow banking system was market driven. Lack of confidence and financial innovation on the mainstream banking system to structure financial products that improve intermediation gave space for shadow banking growth. In response to this development, the researcher recommended that regulatory focus should be on the functions of shadow banks rather than institutions; this will be more inclusive and efficient in avoiding innovative creation of new entities that perform the same shadow banking functions. Also, the Zimbabwean formal banking system should be innovative in-line with the development of the international banking models.

  20. Simple Machines Made Simple.

    Science.gov (United States)

    St. Andre, Ralph E.

    Simple machines have become a lost point of study in elementary schools as teachers continue to have more material to cover. This manual provides hands-on, cooperative learning activities for grades three through eight concerning the six simple machines: wheel and axle, inclined plane, screw, pulley, wedge, and lever. Most activities can be…

  1. Improving Students’ Listening Skill Through Shadowing

    Directory of Open Access Journals (Sweden)

    Mukminatus Zuhriyah

    2016-12-01

    Full Text Available Listening is the first part of language skills that everyone gets when learning a language. It comes before speaking, reading, and writing. Meanwhile, most of the students get difficulty to learn listening of a foreign language, especially English. That is why shadowing was applied in the listening class as one of the solutions to make the learners of English listening easy to understand what the speaker says. This collaborative classroom action research was generally to know whether or not shadowing could improve the students listening skill. It was also specifically to know: (1 the lecturer’s activities, (2 the students’ activities, and (3 the students’ responses during the implementation of shadowing in the listening class. The subjects were 18 students of the third semester of English department of education faculty of Hasyim Asy’ari university (UNHASY Tebuireng Jombang in the academic year of 2016/2017. The data were obtained from the observations got from the notes written by the collaborator and the listening test. The students’ listening skill improved after the implementation of shadowing. It could be seen in the improvement of mean score, from 74.2 in cycle one to 75 in cycle two. Then, the precentage of students passing the minimum mastery criteria also improved, from 61% in cycle one to 77.8% in cycle two. Thus, it can be concluded that shadowing could improve students’ listening skill.

  2. Shadows alter facial expressions of Noh masks.

    Directory of Open Access Journals (Sweden)

    Nobuyuki Kawai

    Full Text Available BACKGROUND: A Noh mask, worn by expert actors during performance on the Japanese traditional Noh drama, conveys various emotional expressions despite its fixed physical properties. How does the mask change its expressions? Shadows change subtly during the actual Noh drama, which plays a key role in creating elusive artistic enchantment. We here describe evidence from two experiments regarding how attached shadows of the Noh masks influence the observers' recognition of the emotional expressions. METHODOLOGY/PRINCIPAL FINDINGS: In Experiment 1, neutral-faced Noh masks having the attached shadows of the happy/sad masks were recognized as bearing happy/sad expressions, respectively. This was true for all four types of masks each of which represented a character differing in sex and age, even though the original characteristics of the masks also greatly influenced the evaluation of emotions. Experiment 2 further revealed that frontal Noh mask images having shadows of upward/downward tilted masks were evaluated as sad/happy, respectively. This was consistent with outcomes from preceding studies using actually tilted Noh mask images. CONCLUSIONS/SIGNIFICANCE: Results from the two experiments concur that purely manipulating attached shadows of the different types of Noh masks significantly alters the emotion recognition. These findings go in line with the mysterious facial expressions observed in Western paintings, such as the elusive qualities of Mona Lisa's smile. They also agree with the aesthetic principle of Japanese traditional art "yugen (profound grace and subtlety", which highly appreciates subtle emotional expressions in the darkness.

  3. Neutron shielding material

    International Nuclear Information System (INIS)

    Nodaka, M.; Iida, T.; Taniuchi, H.; Yosimura, K.; Nagahama, H.

    1993-01-01

    From among the neutron shielding materials of the 'kobesh' series developed by Kobe Steel, Ltd. for transport and storage packagings, silicon rubber base type material has been tested for several items with a view to practical application and official authorization, and in order to determine its adaptability to actual vessels. Silicon rubber base type 'kobesh SR-T01' is a material in which, from among the silicone rubber based neutron shielding materials, the hydrogen content is highest and the boron content is most optimized. Its neutron shielding capability has been already described in the previous report (Taniuchi, 1986). The following tests were carried out to determine suitability for practical application; 1) Long-term thermal stability test 2) Pouring test on an actual-scale model 3) Fire test The experimental results showed that the silicone rubber based neutron shielding material has good neutron shielding capability and high long-term fire resistance, and that it can be applied to the advanced transport packaging. (author)

  4. Method for dismantling shields

    International Nuclear Information System (INIS)

    Fukuzawa, Rokuro; Kondo, Nobuhiro; Kamiyama, Yoshinori; Kawasato, Ken; Hiraga, Tomoaki.

    1990-01-01

    The object of the present invention is to enable operators to dismantle shieldings contaminated by radioactivity easily and in a short period of time without danger of radiation exposure. A plurality of introduction pipes are embedded previously to the shielding walls of shielding members which contain a reactor core in a state where both ends of the introduction pipes are in communication with the outside. A wire saw is inserted into the introduction pipes to cut the shieldings upon dismantling. Then, shieldings can be dismantled easily in a short period of time with no radiation exposure to operator's. Further, according to the present invention, since the wire saw can be set easily and a large area can be cut at once, operation efficiency is improved. Further, since remote control is possible, cutting can be conducted in water and complicated places of the reactor. Biting upon starting the wire saw in the introduction pipe is reduced to facilitate startup for the rotation. (I.S.)

  5. Double-layer neutron shield design as neutron shielding application

    Science.gov (United States)

    Sariyer, Demet; Küçer, Rahmi

    2018-02-01

    The shield design in particle accelerators and other high energy facilities are mainly connected to the high-energy neutrons. The deep penetration of neutrons through massive shield has become a very serious problem. For shielding to be efficient, most of these neutrons should be confined to the shielding volume. If the interior space will become limited, the sufficient thickness of multilayer shield must be used. Concrete and iron are widely used as a multilayer shield material. Two layers shield material was selected to guarantee radiation safety outside of the shield against neutrons generated in the interaction of the different proton energies. One of them was one meter of concrete, the other was iron-contained material (FeB, Fe2B and stainless-steel) to be determined shield thicknesses. FLUKA Monte Carlo code was used for shield design geometry and required neutron dose distributions. The resulting two layered shields are shown better performance than single used concrete, thus the shield design could leave more space in the interior shielded areas.

  6. Radiation shielding material

    International Nuclear Information System (INIS)

    Matsumoto, Akio; Isobe, Eiji.

    1976-01-01

    Purpose: To increase the shielding capacity of the radiation shielding material having an abundant flexibility. Constitution: A mat consisting of a lead or lead alloy fibrous material is covered with a cloth, and the two are made integral by sewing in a kilted fashion by using a yarn. Thereafter, the system is covered with a gas-tight film or sheet. The shielding material obtained in this way has, in addition to the above merits, advantages in that (1) it is free from restoration due to elasticity so that it can readily seal contaminants, (2) it can be used in a state consisting of a number of overlapped layers, (3) it fits the shoulder well and is readily portable and (4) it permits attachment of fasteners or the like. (Ikeda, J.)

  7. Hybrid Active-Passive Radiation Shielding System

    Data.gov (United States)

    National Aeronautics and Space Administration — A radiation shielding system is proposed that integrates active magnetic fields with passive shielding materials. The objective is to increase the shielding...

  8. Glove box shield

    Science.gov (United States)

    Brackenbush, L.W.; Hoenes, G.R.

    A shield for a glove box housing radioactive material is comprised of spaced apart clamping members which maintain three overlapping flaps in place therebetween. There is a central flap and two side flaps, the side flaps overlapping at the interior edges thereof and the central flap extending past the intersection of the side flaps in order to insure that the shield is always closed when the user wthdraws his hand from the glove box. Lead loaded neoprene rubber is the preferred material for the three flaps, the extent of lead loading depending upon the radiation levels within the glove box.

  9. Shadowing effects on vector boson production

    Energy Technology Data Exchange (ETDEWEB)

    Vogt, R.

    2000-11-10

    We explore how nuclear modifications to the nucleon structure functions, shadowing, affect massive gauge boson production in heavy ion collisions at different impact parameters. We calculate the dependence of Z{sup 0}, W{sup +} and W{sup -} production on rapidity and impact parameter to next-to-leading order in Pb+Pb collisions at 5.5 TeV/nucleon to study quark shadowing at high Q{sup 2}. We also compare our Pb+Pb results to the pp rapidity distributions at 14 TeV.

  10. Shadow banking, relationship banking, and the economics of depression

    Directory of Open Access Journals (Sweden)

    Antonio Bianco

    2015-12-01

    Full Text Available The paper explores whether a theory of banks doing ‘finance through money creation’ implies a reconsideration of demand-side macro theory as well. To this aim, a simple methodological accounting model of the influence of financial markets over the real economy is presented. The model allows a tidy comparison of relationship and shadow banking, interpreted as alternative schemes of liquidity (not credit risk management. The model emphasizes the interdependencies in entrepreneurs’ animal spirits, liquidity risk management schemes adopted by financial institutions, and effective demand of households. The underlying idea is that fluctuations in the composition of property incomes trigger fluctuations in non-financial investment that, in turn, drive fluctuations in spending. The article finds that both relationship and shadow banking must have a pro-cyclical impact, and differences are essentially based on different liquidity risk management aggregate cost functions. The model developed here suggests that securitisation does not per se affect the financial sustainability of the growth process, but regulatory measures aimed at checking predatory lending and re-securitisation activities are needed to avoid possible adverse impacts on animal spirits. JEL codes: E44, G20, O16.

  11. Detection and Removal of Chromatic Moving Shadows in Surveillance Scenarios

    DEFF Research Database (Denmark)

    Casado, Ivan Huerta; Holte, Michael Boelstoft; Moeslund, Thomas B.

    2009-01-01

      Segmentation in the surveillance domain has to deal with shadows to avoid distortions when detecting moving objects. Most segmentation approaches dealing with shadow detection are typically restricted to penumbra shadows. Therefore, such techniques cannot cope well with umbra shadows....... Consequently, umbra shadows are usually detected as part of moving objects. In this paper we present a novel technique based on gradient and colour models for separating chromatic moving cast shadows from detected moving objects. Firstly, both a chromatic invariant colour cone model and an invariant gradient...... model are built to perform automatic segmentation while detecting potential shadows. In a second step, regions corresponding to potential shadows are grouped by considering "a bluish effect" and an edge partitioning. Lastly, (i) temporal similarities between textures and (ii) spatial similarities...

  12. Hinged Shields for Machine Tools

    Science.gov (United States)

    Lallande, J. B.; Poland, W. W.; Tull, S.

    1985-01-01

    Flaps guard against flying chips, but fold away for tool setup. Clear plastic shield in position to intercept flying chips from machine tool and retracted to give operator access to workpiece. Machine shops readily make such shields for own use.

  13. Electrostatic shielding of transformers

    Energy Technology Data Exchange (ETDEWEB)

    De Leon, Francisco

    2017-11-28

    Toroidal transformers are currently used only in low-voltage applications. There is no published experience for toroidal transformer design at distribution-level voltages. Toroidal transformers are provided with electrostatic shielding to make possible high voltage applications and withstand the impulse test.

  14. Radiation shielding member

    International Nuclear Information System (INIS)

    Tada, Nobuo; Ito, Masato; Nihei, Ken-ichi; Takeshi, Tetsu

    1998-01-01

    A radiation shielding member comprises a metal vessel and a liquid therein, and is disposed to the upper surface of a lower flange of a reactor core shroud. Waterproof hot wires are contained in the liquid and are connected to a power source disposed at the outside. Electric current is supplied to the hot wires to elevate the temperature of the liquid, and the temperature of the vessel is kept higher than an atmospheric temperature thereby suppressing generation of dew condensation or water droplets. In addition, a water repellent coating is applied to the shielding member itself to prevent deposition of water droplets. Further, the bottom of the shielding member is inclined, and a water droplet-recovering vessel is disposed at the lower portion of the shielding member, so that the water droplets collected by the inclination of the bottom are recovered to the water droplet recovering vessel. With such a constitution, access of an operator to the inside of a reactor pressure vessel is facilitated, and at the same time, the working circumstance at the reactor bottom can be improved. (I.N.)

  15. Shield For Flexible Pipe

    Science.gov (United States)

    Ponton, Michael K.; Williford, Clifford B.; Lagen, Nicholas T.

    1995-01-01

    Cylindrical shield designed to fit around flexible pipe to protect nearby workers from injury and equipment from damage if pipe ruptures. Designed as pressure-relief device. Absorbs impact of debris ejected radially from broken flexible pipe. Also redirects flow of pressurized fluid escaping from broken pipe onto flow path allowing for relief of pressure while minimizing potential for harm.

  16. Heat shielding device

    International Nuclear Information System (INIS)

    Yatabe, Hiroshi; Motoya, Koji; Kodama, Hiroshi.

    1997-01-01

    Panel-like water cooling tubes are disposed on a shielding concrete wall as a floor surface on which a reactor pressure vessel of a HTGR type reactor is settled. The panel like water cooling tube comprises a large number of water cooling tubes and fin plates connecting them with each other. A heat shielding device is disposed to the opening of an air vent hole on the shielding concrete wall. The heat shielding device has a plurality of supports are disposed between a disk-like upper support plate larger than the opening of the vent hole and covered with a heat insulation material and a lower support plate having a vent hole at the center. The lower support plate is connected with the fin plate. A portion between the supports is formed as pressure releasing channels. Radiation heat from the reactor pressure vessel is transferred to the fin plate by way of the upper support plate, support and a lower support plate and transferred to cooling water of a water-cooling pipeline. Accordingly, radiation heat of the reactor pressure vessel is not transferred to the vent holes. (I.N.)

  17. Spacecraft Electrostatic Radiation Shielding

    Science.gov (United States)

    2008-01-01

    This project analyzed the feasibility of placing an electrostatic field around a spacecraft to provide a shield against radiation. The concept was originally proposed in the 1960s and tested on a spacecraft by the Soviet Union in the 1970s. Such tests and analyses showed that this concept is not only feasible but operational. The problem though is that most of this work was aimed at protection from 10- to 100-MeV radiation. We now appreciate that the real problem is 1- to 2-GeV radiation. So, the question is one of scaling, in both energy and size. Can electrostatic shielding be made to work at these high energy levels and can it protect an entire vehicle? After significant analysis and consideration, an electrostatic shield configuration was proposed. The selected architecture was a torus, charged to a high negative voltage, surrounding the vehicle, and a set of positively charged spheres. Van de Graaff generators were proposed as the mechanism to move charge from the vehicle to the torus to generate the fields necessary to protect the spacecraft. This design minimized complexity, residual charge, and structural forces and resolved several concerns raised during the internal critical review. But, it still is not clear if such a system is costeffective or feasible, even though several studies have indicated usefulness for radiation protection at energies lower than that of the galactic cosmic rays. Constructing such a system will require power supplies that can generate voltages 10 times that of the state of the art. Of more concern is the difficulty of maintaining the proper net charge on the entire structure and ensuring that its interaction with solar wind will not cause rapid discharge. Yet, if these concerns can be resolved, such a scheme may provide significant radiation shielding to future vehicles, without the excessive weight or complexity of other active shielding techniques.

  18. Shadow mask evaporation through monolayer modified nanostencils

    NARCIS (Netherlands)

    Kolbel, M.; Tjerkstra, R.W.; Brugger, J.P.; van Rijn, C.J.M.; Nijdam, W.; Huskens, Jurriaan; Reinhoudt, David

    2002-01-01

    Gradual clogging of the apertures of nanostencils used as miniature shadow masks in metal evaporations can be reduced by coating the stencil with self-assembled monolayers (SAM). This is quantified by the dimensions (height and volume) of gold features obtained by nanostencil evaporation as measured

  19. Hunting the Shadow, Catching the Light

    DEFF Research Database (Denmark)

    Toft, Anne Elisabeth; Nielsen, Torben

    2009-01-01

    From 28 October to 6 November 2009 twenty-one 3rd year students in interior design from Central Academy of Fine Arts (CAFA), School of Architecture, Beijing participated in the workshop Hunting the Shadow - Catching the Light. The workshop was conceived and led by the Danish architects Torben...

  20. Shadow Science: Astronomy in the Schoolyard

    Science.gov (United States)

    Denney, Janice

    2005-01-01

    It is natural to study astronomy outdoors, but it is not quite as natural to study astronomy during the daytime. This lesson uses the Earth's closest star as a subject of study within the schoolyard. The importance of the rising sun is combined with hands-on inquiry in which students explore the properties of shadows. Students (a) complete a…

  1. Boundary Correct Real-Time Soft Shadows

    DEFF Research Database (Denmark)

    Jacobsen, Bjarke; Christensen, Niels Jørgen; Larsen, Bent Dalgaard

    2004-01-01

    This paper describes a method to determine correct shadow boundaries from an area light source using umbra and penumbra volumes. The light source is approximated by a circular disk as this gives a fast way to extrude the volumes. The method also gives a crude estimate of the visibility of the are...

  2. SHADOW PROCESSES INSTATE BUDGET: CURRENT CONDITION AND DETERMINING FACTORS

    Directory of Open Access Journals (Sweden)

    Z. Varnalii

    2014-12-01

    Full Text Available The most significant factors that move state budget into the shadow are determined. Current condition of shadow processes in state budget is highlighted. The paper also provides an analysis of relationship between political processes and shadow economy in public sector of Ukraine.

  3. Shielding experiments for accelerator facilities

    Energy Technology Data Exchange (ETDEWEB)

    Nakashima, Hiroshi; Tanaka, Susumu; Sakamoto, Yukio [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment] [and others

    2000-06-01

    A series of shielding experiments was carried out by using AVF cyclotron accelerator of TIARA at JAERI in order to validate shielding design methods for accelerator facilities in intermediate energy region. In this paper neutron transmission experiment through thick shields and radiation streaming experiment through a labyrinth are reported. (author)

  4. Shielding experiments for accelerator facilities

    International Nuclear Information System (INIS)

    Nakashima, Hiroshi; Tanaka, Susumu; Sakamoto, Yukio

    2000-01-01

    A series of shielding experiments was carried out by using AVF cyclotron accelerator of TIARA at JAERI in order to validate shielding design methods for accelerator facilities in intermediate energy region. In this paper neutron transmission experiment through thick shields and radiation streaming experiment through a labyrinth are reported. (author)

  5. Shielding Design and Radiation Shielding Evaluation for LSDS System Facility

    International Nuclear Information System (INIS)

    Kim, Younggook; Kim, Jeongdong; Lee, Yongdeok

    2015-01-01

    As the system characteristics, the target in the spectrometer emits approximately 1012 neutrons/s. To efficiently shield the neutron, the shielding door designs are proposed for the LSDS system through a comparison of the direct shield and maze designs. Hence, to guarantee the radiation safety for the facility, the door design is a compulsory course of the development of the LSDS system. To improve the shielding rates, 250x250 covering structure was added as a subsidiary around the spectrometer. In this study, the evaluations of the suggested shielding designs were conducted using MCNP code. The suggested door design and covering structures can shield the neutron efficiently, thus all evaluations of all conditions are satisfied within the public dose limits. From the Monte Carlo code simulation, Resin(Indoor type) and Tungsten(Outdoor type) were selected as the shielding door materials. From a comparative evaluation of the door thickness, In and Out door thickness was selected 50 cm

  6. SmartShadow models and methods for pervasive computing

    CERN Document Server

    Wu, Zhaohui

    2013-01-01

    SmartShadow: Models and Methods for Pervasive Computing offers a new perspective on pervasive computing with SmartShadow, which is designed to model a user as a personality ""shadow"" and to model pervasive computing environments as user-centric dynamic virtual personal spaces. Just like human beings' shadows in the physical world, it follows people wherever they go, providing them with pervasive services. The model, methods, and software infrastructure for SmartShadow are presented and an application for smart cars is also introduced.  The book can serve as a valuable reference work for resea

  7. Do Elementary Science Methods Textbooks Promote Understanding of Shadows?

    Directory of Open Access Journals (Sweden)

    Lloyd H. Barrow

    2016-02-01

    Full Text Available Elementary science methods textbooks can be an important resource for future elementary teachers of science. Since shadows are a common topic in elementary school and Next Generation Science Standards (NGSS Lead States, 2013. A series of ten shadows concepts were formed into a learning progression by Wizman and Fortus (2007. For this research, ten science methods textbook were read and analyzed about how each of the shadow concepts were addressed. These methods textbooks focused on a limited number of shadow concepts. Consequently, as a future reference, they are very limited in addressing all ten shadow concepts.

  8. Shielding container for radioactive isotopes

    International Nuclear Information System (INIS)

    Sumi, Tetsuo; Tosa, Masayoshi; Hatogai, Tatsuaki.

    1975-01-01

    Object: To effect opening and closing bidirectional radiation used particularly for a gamma densimeter or the like by one operation. Structure: This device comprises a rotatable shielding body for receiving radioactive isotope in the central portion thereof and having at least two radiation openings through which radiation is taken out of the isotope, and a shielding container having openings corresponding to the first mentioned radiation openings, respectively. The radioactive isotope is secured to a rotational shaft of the shielding body, and the shielding body is rotated to register the openings of the shielding container with the openings of the shielding body or to shield the openings, thereby effecting radiation and cut off of gamma ray in the bidirection by one operation. (Kamimura, M.)

  9. Primary shield displacement and bowing

    International Nuclear Information System (INIS)

    Scott, K.V.

    1978-01-01

    The reactor primary shield is constructed of high density concrete and surrounds the reactor core. The inlet, outlet and side primary shields were constructed in-place using 2.54 cm (1 in) thick steel plates as the forms. The plates remained as an integral part of the shields. The elongation of the pressure tubes due to thermal expansion and pressurization is not moving through the inlet nozzle hardware as designed but is accommodated by outward displacement and bowing of the inlet and outlet shields. Excessive distortion of the shields may result in gas seal failures, intolerable helium gas leaks, increased argon-41 emissions, and shield cooling tube failures. The shield surveillance and testing results are presented

  10. Light shielding apparatus

    Energy Technology Data Exchange (ETDEWEB)

    Miller, Richard Dean; Thom, Robert Anthony

    2017-10-10

    A light shielding apparatus for blocking light from reaching an electronic device, the light shielding apparatus including left and right support assemblies, a cross member, and an opaque shroud. The support assemblies each include primary support structure, a mounting element for removably connecting the apparatus to the electronic device, and a support member depending from the primary support structure for retaining the apparatus in an upright orientation. The cross member couples the left and right support assemblies together and spaces them apart according to the size and shape of the electronic device. The shroud may be removably and adjustably connectable to the left and right support assemblies and configured to take a cylindrical dome shape so as to form a central space covered from above. The opaque shroud prevents light from entering the central space and contacting sensitive elements of the electronic device.

  11. Shielding benchmark test

    International Nuclear Information System (INIS)

    Kawai, Masayoshi

    1984-01-01

    Iron data in JENDL-2 have been tested by analyzing shielding benchmark experiments for neutron transmission through iron block performed at KFK using CF-252 neutron source and at ORNL using collimated neutron beam from reactor. The analyses are made by a shielding analysis code system RADHEAT-V4 developed at JAERI. The calculated results are compared with the measured data. As for the KFK experiments, the C/E values are about 1.1. For the ORNL experiments, the calculated values agree with the measured data within an accuracy of 33% for the off-center geometry. The d-t neutron transmission measurements through carbon sphere made at LLNL are also analyzed preliminarily by using the revised JENDL data for fusion neutronics calculation. (author)

  12. Exposing image forgery by detecting consistency of shadow.

    Science.gov (United States)

    Ke, Yongzhen; Qin, Fan; Min, Weidong; Zhang, Guiling

    2014-01-01

    We propose two tampered image detection methods based on consistency of shadow. The first method is based on texture consistency of shadow for the first kind of splicing image, in which the shadow as well as main body is copied and pasted from another image. The suspicious region including shadow and nonshadow is first selected. Then texture features of the shadow region and the nonshadow region are extracted. Last, correlation function is used to measure the similarity of the two texture features. By comparing the similarity, we can judge whether the image is tampered. Due to the failure in detecting the second kind of splicing image, in which main body, its shadow, and surrounding regions are copied and pasted from another image, another method based on strength of light source of shadows is proposed. The two suspicious shadow regions are first selected. Then an efficient method is used to estimate the strength of light source of shadow. Last, the similarity of strength of light source of two shadows is measured by correlation function. By combining the two methods, we can detect forged image with shadows. Experimental results demonstrate that the proposed methods are effective despite using simplified model compared with the existing methods.

  13. Exposing Image Forgery by Detecting Consistency of Shadow

    Directory of Open Access Journals (Sweden)

    Yongzhen Ke

    2014-01-01

    Full Text Available We propose two tampered image detection methods based on consistency of shadow. The first method is based on texture consistency of shadow for the first kind of splicing image, in which the shadow as well as main body is copied and pasted from another image. The suspicious region including shadow and nonshadow is first selected. Then texture features of the shadow region and the nonshadow region are extracted. Last, correlation function is used to measure the similarity of the two texture features. By comparing the similarity, we can judge whether the image is tampered. Due to the failure in detecting the second kind of splicing image, in which main body, its shadow, and surrounding regions are copied and pasted from another image, another method based on strength of light source of shadows is proposed. The two suspicious shadow regions are first selected. Then an efficient method is used to estimate the strength of light source of shadow. Last, the similarity of strength of light source of two shadows is measured by correlation function. By combining the two methods, we can detect forged image with shadows. Experimental results demonstrate that the proposed methods are effective despite using simplified model compared with the existing methods.

  14. FIELD INVESTIGATION OF THE DRIFT SHADOW

    International Nuclear Information System (INIS)

    G.W. Su; T.J. Kneafsey

    2006-01-01

    A drift shadow is an area immediately beneath an underground void that, in theory, will be relatively drier than the surrounding rock mass. Numerical and analytical models of water flow through unsaturated rock predict the existence of a drift shadow, but field tests confirming the existence of the drift shadow have yet to be performed. Proving the existence of drift shadows and understanding their hydrologic and transport characteristics could provide a better understanding of how contaminants move in the subsurface if released from waste emplacement drifts such as the proposed nuclear waste repository at Yucca Mountain, Nevada. We describe the field program that will be used to investigate the existence of a drift shadow--and the corresponding hydrological process at the Hazel-Atlas silica-sand mine located at the Black Diamond Mines Regional Preserve in Antioch, California. The location and configuration of this mine makes it an excellent site to observe and measure drift shadow characteristics. The mine is located in a porous sandstone unit of the Domengine formation, an approximately 230 meter thick series of interbedded Eocene-age shales, coals, and massive-bedded sandstones. The mining method used at the mine required the development of two parallel drifts, one above the other, driven along the strike of the mined sandstone stratum. This configuration provides the opportunity to introduce water into the rock mass in the upper drift and to observe and measure its flow around the underlying drift. The passive and active hydrologic tests to be performed are described. In the passive method, cores will be obtained in a radial pattern around a drift and will be sectioned and analyzed for in-situ water content using a gravimetric technique, as well as analyzed for chemistry. With the active hydrologic test, water will be introduced into the upper drift of the two parallel drifts and the flow of the water will be tracked as it passes near the bottom drift

  15. Rural-to-urban migration and the shadow wage in LDCs.

    Science.gov (United States)

    Renard, R

    1984-04-01

    "This paper discusses the amount of rural-to-urban migration which will be forthcoming when a new urban job is created for which an institutionally fixed wage above the market-clearing level is offered. A simple formula is proposed to estimate migration response. It can be used to calculate the shadow wage in cost-benefit analysis (CBA) in less developed countries (LDCs)." excerpt

  16. Neutron shielding materials

    International Nuclear Information System (INIS)

    Tomoshige, Toru; Fujii, Yasumasa; Nifuku, Masataka.

    1985-01-01

    Purpose: To obtain shielding materials excellent in heat and radiation resistance, as well as having mechanical strength in a reduced weight. Constitution: A mixture comprising from 30 to 80 % by weight of epoxy resin, from 5 to 50 % by weight of polyethylene and from 1 to 50 % by weight of inorganic boron compound is cured to prepare a neutron shielding material. The epoxy resin used herein is a compound having more than 18 epoxy groups per one molecule. Polyethylene is a polyethylene homopolymer or a copolymer of ethylene and less than 10 % of other copolymerizable monomer which is preferably powdery and in the grain size of from 10 to 200 μm. The inorganic boric compound can include, for example, boron carbide, boron nitride and anhydrous boric acid. As the curing agent, all sorts of compounds known as the curing agent for epoxy resins can be used. The shielding material is excellent in heat resistance, particularly, in the strength, thermal deformation temperature and the bondability at high temperature and also satisfactory in compression strength and bondability. (Kawakami, Y.)

  17. MPPT-Based Control Algorithm for PV System Using iteration-PSO under Irregular shadow Conditions

    Directory of Open Access Journals (Sweden)

    M. Abdulkadir

    2017-02-01

    Full Text Available The conventional maximum power point tracking (MPPT techniques can hardly track the global maximum power point (GMPP because the power-voltage characteristics of photovoltaic (PV exhibit multiple local peaks in irregular shadow, and therefore easily fall into the local maximum power point. These conditions make it very challenging, and to tackle this deficiency, an efficient Iteration Particle Swarm Optimization (IPSO has been developed to improve the quality of solution and convergence speed of the traditional PSO, so that it can effectively track the GMPP under irregular shadow conditions. This proposed technique has such advantages as simple structure, fast response and strong robustness, and convenient implementation. It is applied to MPPT control of PV system in irregular shadow to solve the problem of multi-peak optimization in partial shadow. In order to verify the rationality of the proposed algorithm, however, recently the dynamic MPPT performance under varying irradiance conditions has been given utmost attention to the PV society. As the European standard EN 50530 which defines the recommended varying irradiance profiles, was released lately, the corresponding researchers have been required to improve the dynamic MPPT performance. This paper tried to evaluate the dynamic MPPT performance using EN 50530 standard. The simulation results show that iterative-PSO method can fast track the global MPP, increase tracking speed and higher dynamic MPPT efficiency under EN 50530 than the conventional PSO.

  18. Fading and Shadowing in Wireless Systems

    CERN Document Server

    Shankar, P Mohana

    2012-01-01

    In recent decades, growth in the field of wireless communications has led to an exponential rise in the number of journals catering to the research community. Still unmet, however, is the need to fully and comprehensively understand the effects of channel degradation brought on by the statistical fluctuations in the channel. These fluctuations mainly manifest as variations in signal power observed in the channel generally modeled using a variety of probability distributions, both in straight forms as well as in compound forms. While the former might explain some of the effects, it is the latter, namely, the compound models, which incorporate both short term and long term power fluctuations in the channel, explain the much more complex nature of the signals in these channels. Fading and Shadowing in Wireless Systems offers a pedagogical approach to the topic, with insight into the modeling and analysis of fading and shadowing. Beginning with statistical background and digital communications, the book is formul...

  19. Fuzzy split and merge for shadow detection

    Directory of Open Access Journals (Sweden)

    Remya K. Sasi

    2015-03-01

    Full Text Available Presence of shadow in an image often causes problems in computer vision applications such as object recognition and image segmentation. This paper proposes a method to detect the shadow from a single image using fuzzy split and merge approach. Split and merge is a classical algorithm used in image segmentation. Predicate function in the classical approach is replaced by a Fuzzy predicate in the proposed approach. The method follows a top down approach of recursively splitting an image into homogeneous quadtree blocks, followed by a bottom up approach by merging adjacent unique regions. The method has been compared with previous approaches and found to be better in performance in terms of accuracy.

  20. Shadow of rotating wormhole in plasma environment

    Science.gov (United States)

    Abdujabbarov, Ahmadjon; Juraev, Bakhtinur; Ahmedov, Bobomurat; Stuchlík, Zdeněk

    2016-07-01

    The massless particle motion around rotating wormhole in the presence of plasma environment has been studied. It has been shown that the presence of the plasma decreases the inner radius of the circular orbits of photons around rotating wormhole. The shadow cast by rotating wormhole surrounded by inhomogeneous plasma with the radial power-law density has been explored. It has been shown that the shape and size of the wormhole shadow is distorted and changed depending on i) plasma parameters, ii) wormhole rotation and iii) inclination angle between observer plane and axis of rotation of wormhole. As an example we have considered an inverse radial distribution of the plasma density and different types of the wormhole solution.

  1. Jig Aligns Shadow Mask On CCD

    Science.gov (United States)

    Matus, Carlos V.

    1989-01-01

    Alignment viewed through microscope. Alignment jig positions shadow mask on charge-coupled device (CCD) so metal film deposited on it precisely. Allows CCD package to be inserted and removed without disturbing alignment of mask. Holds CCD packages securely and isolates it electrostatically while providing electrical contact to each of its pins. When alignment jig assembled with CCD, used to move mask under micrometer control.

  2. Improving Students' Listening Skill Through Shadowing

    OpenAIRE

    Zuhriyah, Mukminatus

    2016-01-01

    Listening is the first part of language skills that everyone gets when learning a language. It comes before speaking, reading, and writing. Meanwhile, most of the students get difficulty to learn listening of a foreign language, especially English. That is why shadowing was applied in the listening class as one of the solutions to make the learners of English listening easy to understand what the speaker says. This collaborative classroom action research was generally to know whether or not s...

  3. The 'Shadow of Succession' in Family Firms

    OpenAIRE

    Diwisch, Sandra Denise; Voithofer, Peter; Weiss, Christoph

    2005-01-01

    The paper analyses the relationship between succession and firm performance. Using a unique panel data set on a sample of roughly 4,000 Austrian family firms we examine empirically the impact of past succession as well as future succession plans on employment growth and investment behaviour. Analysing succession plans, we do not find a 'shadow of succession' effect. No significant difference in employment growth and investment behaviour is found between firms that plan to transfer the firm in...

  4. A contribution to shielding effectiveness analysis of shielded tents

    Directory of Open Access Journals (Sweden)

    Vranić Zoran M.

    2004-01-01

    Full Text Available An analysis of shielding effectiveness (SE of the shielded tents made of the metallised fabrics is given. First, two electromagnetic characteristic fundamental for coupling through electrically thin shield, the skin depth break frequency and the surface resistance or transfer impedance, is defined and analyzed. Then, the transfer function and the SE are analyzed regarding to the frequency range of interest to the Electromagnetic Compatibility (EMC Community.

  5. Shadow Radiation Shield Required Thickness Estimation for Space Nuclear Power Units

    Science.gov (United States)

    Voevodina, E. V.; Martishin, V. M.; Ivanovsky, V. A.; Prasolova, N. O.

    The paper concerns theoretical possibility of visiting orbital transport vehicles based on nuclear power unit and electric propulsion system on the Earth's orbit by astronauts to maintain work with payload from the perspective of radiation safety. There has been done estimation of possible time of the crew's staying in the area of payload of orbital transport vehicles for different reactor powers, which is a consistent part of nuclear power unit.

  6. Measurement of the transient shielding effectiveness of shielding cabinets

    Directory of Open Access Journals (Sweden)

    H. Herlemann

    2008-05-01

    Full Text Available Recently, new definitions of shielding effectiveness (SE for high-frequency and transient electromagnetic fields were introduced by Klinkenbusch (2005. Analytical results were shown for closed as well as for non closed cylindrical shields. In the present work, the shielding performance of different shielding cabinets is investigated by means of numerical simulations and measurements inside a fully anechoic chamber and a GTEM-cell. For the GTEM-cell-measurements, a downscaled model of the shielding cabinet is used. For the simulations, the numerical tools CONCEPT II and COMSOL MULTIPHYSICS were available. The numerical results agree well with the measurements. They can be used to interpret the behaviour of the shielding effectiveness of enclosures as function of frequency. From the measurement of the electric and magnetic fields with and without the enclosure in place, the electric and magnetic shielding effectiveness as well as the transient shielding effectiveness of the enclosure are calculated. The transient SE of four different shielding cabinets is determined and discussed.

  7. Infant Perception of Incongruent Shapes in Cast Shadows

    Directory of Open Access Journals (Sweden)

    Kazuki Sato

    2015-04-01

    Full Text Available A cast shadow occurs when an object blocks the light from an illumination and projects a dark region onto a surface. Previous studies have reported that adults are slower to identify an object when the object has an incongruent cast shadow than when it has a congruent cast shadow (Castiello, 2001. Here, we used the familiarization-novelty preference procedure to examine whether 5- to 8-month-old infants could detect the relationship between object shapes and cast shadows. In Experiment 1, we examined the infants' ability to detect incongruency between objects and cast shadows. Results showed that 7- to 8-month olds could detect incongruence between the object shapes and the cast shadows, whereas 5- to 6-month olds did not. Yet, our control experiment showed that infants could not detect this incongruence from stimuli in which a white outline had been added to the original cast shadow to decrease the possibility of it being perceived as a cast shadow (Experiment 2. The results of these experiments demonstrate that 7- to 8-month olds responded to the congruence of cast shadows and to consistent contrast polarity between the cast shadow and its background.

  8. SU-F-I-71: Fetal Protection During Fluoroscopy: To Shield Or Not to Shield?

    Energy Technology Data Exchange (ETDEWEB)

    Joshi, S; Vanderhoek, M [Henry Ford Health System, Detroit, MI (United States)

    2016-06-15

    Purpose: Lead aprons are routinely used to shield the fetus from radiation during fluoroscopically guided interventions (FGI) involving pregnant patients. When placed in the primary beam, lead aprons often reduce image quality and increase fluoroscopic radiation output, which can adversely affect fetal dose. The purpose of this work is to identify an effective and practical method to reduce fetal dose without affecting image quality. Methods: A pregnant patient equivalent abdominal phantom is set on the table along with an image quality test object (CIRS model 903) representing patient anatomy of interest. An ion chamber is positioned at the x-ray beam entrance to the phantom, which is used to estimate the relative fetal dose. For three protective methods, image quality and fetal dose measurements are compared to baseline (no protection):1. Lead apron shielding the entire abdomen; 2. Lead apron shielding part of the abdomen, including the fetus; 3. Narrow collimation such that fetus is excluded from the primary beam. Results: With lead shielding the entire abdomen, the dose is reduced by 80% relative to baseline along with a drastic deterioration of image quality. With lead shielding only the fetus, the dose is reduced by 65% along with complete preservation of image quality, since the image quality test object is not shielded. However, narrow collimation results in 90% dose reduction and a slight improvement of image quality relative to baseline. Conclusion: The use of narrow collimation to protect the fetus during FGI is a simple and highly effective method that simultaneously reduces fetal dose and maintains sufficient image quality. Lead aprons are not as effective at fetal dose reduction, and if placed improperly, they can severely degrade image quality. Future work aims to investigate a wider variety of fluoroscopy systems to confirm these results across many different system geometries.

  9. Field investigation of the drift shadow

    International Nuclear Information System (INIS)

    Su, Grace W.; Kneafsey, Timothy J.; Ghezzehei, Teamrat A.; Marshall, Brian D.; Cook, Paul J.

    2005-01-01

    A drift shadow is an area immediately beneath an underground void that, in theory, will be relatively drier than the surrounding rockmass. Numerical and analytical models of water flow through unsaturated rock predict the existence of a drift shadow, but field tests confirming its existence have yet to be performed. Proving the existence of drift shadows and understanding their hydrologic and transport characteristics could provide a better understanding of how contaminants move in the subsurface if released from waste emplacement drifts such as the proposed nuclear waste repository at Yucca Mountain, Nevada. We describe the field program that will be used to investigate the existence of a drift shadow and the corresponding hydrological process at the Hazel-Atlas silica-sandmine located at the Black Diamond Mines Regional Preserve in Antioch, California. The location and configuration of this mine makes it an excellent site to observe and measure drift shadow characteristics. The mine is located in a porous sandstone unit of the Domengine Formation, an approximately 230 meter thick series of interbedded Eocene-age shales, coals, and massive-bedded sandstones. The mining method used at the mine required the development of two parallel drifts, one above the other, driven along the strike of the mined sandstone stratum. This configuration provides the opportunity to introduce water into the rockmass in the upper drift and to observe and measure its flow around the underlying drift. The passive and active hydrologic tests to be performed are described. In the passive method, cores will be obtained in a radial pattern around a drift and will be sectioned and analyzed for in-situ water content and chemical constituents. With the active hydrologic test, water will be introduced into the upper drift of the two parallel drifts and the flow of the water will be tracked as it passes near the bottom drift. Tensiometers, electrical resistance probes, neutron probes, and ground

  10. Neutron Shielding composition

    International Nuclear Information System (INIS)

    Seki, Kiiro; Okuda, Hisashi; Harada, Yoshihisa.

    1994-01-01

    1, 3-bis (N, N-diglycidyl aminomethyl) cyclohexane as a specific epoxy resin is used together with a usual epoxy resin. A polyamine mixture and an imidazole type compound are used as a hardening agent. Further, a boron compound and an inorganic filler are added. Such a neutron shielding composition is hardened at a normal temperature without requiring heating, and mechanical strength, especially, compression strength can be kept over a wide range from low temperature to high temperature after the hardening. (T.M.)

  11. A shield against distraction

    OpenAIRE

    Halin, N.; Marsh, J.E.; Hellman, A.; Hellstrom, I.; Sörqvist, Patrik

    2014-01-01

    In this paper, we apply the basic idea of a trade-off between the level of concentration and distractibility to test whether a manipulation of task difficulty can shield against distraction. Participants read, either in quiet or with a speech noise background, texts that were displayed either in an easy-to-read or a hard-to-read font. Background speech impaired prose recall, but only when the text was displayed in the easy-to-read font. Most importantly, recall was better in the background sp...

  12. Neutronic reactor thermal shield

    International Nuclear Information System (INIS)

    Lowe, P.E.

    1976-01-01

    A shield for a nuclear reactor includes at least two layers of alternating wide and narrow rectangular blocks so arranged that the spaces between blocks in adjacent layers are out of registry, each block having an opening therein equally spaced from the sides of the blocks and nearer the top of the block than the bottom, the distance from the top of the block to the opening in one layer being different from this distance in adjacent layers, openings in blocks in adjacent layers being in registry. 1 claim, 7 drawing figures

  13. Selective shielding device for scintiphotography

    International Nuclear Information System (INIS)

    Harper, J.W.; Kay, T.D.

    1976-01-01

    A selective shielding device to be used in combination with a scintillation camera is described. The shielding device is a substantially oval-shaped configuration removably secured to the scintillation camera. As a result of this combination scanning of preselected areas of a patient can be rapidly and accurately performed without the requirement of mounting any type of shielding paraphernalia on the patient. 1 claim, 2 drawing figures

  14. Measuring space radiation shielding effectiveness

    OpenAIRE

    Bahadori Amir; Semones Edward; Ewert Michael; Broyan James; Walker Steven

    2017-01-01

    Passive radiation shielding is one strategy to mitigate the problem of space radiation exposure. While space vehicles are constructed largely of aluminum, polyethylene has been demonstrated to have superior shielding characteristics for both galactic cosmic rays and solar particle events due to the high hydrogen content. A method to calculate the shielding effectiveness of a material relative to reference material from Bragg peak measurements performed using energetic heavy charged particles ...

  15. Shielding considerations and design concepts for space applications

    International Nuclear Information System (INIS)

    Bloomfield, H.S.

    1991-01-01

    This paper presents a summary of shielding considerations and design concepts that have been under investigation at the National Aeronautics and Space Administration's (NASA's) Lewis Research Center for the application of space reactor power systems to a wide range of future NASA missions. The missions are based on the NASA Space Exploration Initiative (SEI) and Mission from Plant Earth programs currently under study. They include both instrument and human-rated applications in cislunar and outer space as well as planet surface locations. The SRPS configurations under consideration are based on advanced reactor and power-generation technologies being developed jointly by the US Department of Energy/NASA/US Department of Defense SP-100 space reactor power system program and the NASA Civil Space Technology Initiative programs. The SP-100 reactor technology employs a UN-fueled, niobium-alloy-clad, pin-type core with high-temperature lithium coolant. Electrical power generation technologies include both direct or static and dynamic thermal-to-electrical conversion techniques, with selection dependent on mission power-level requirements. Shield designs are also highly mission dependent and can range from shadow-shield configurations employing tungsten and lithium hydride (LiH) materials manufactured and assembled on Earth, to the use of indigenous planet surface materials that could be utilized on the moon and Mars

  16. Multifunctional Hot Structure Heat Shield

    Data.gov (United States)

    National Aeronautics and Space Administration — This project is performing preliminary development of a Multifunctional Hot Structure (HOST) heat shield for planetary entry. Results of this development will...

  17. Clustered deep shadow maps for integrated polyhedral and volume rendering

    KAUST Repository

    Bornik, Alexander

    2012-01-01

    This paper presents a hardware-accelerated approach for shadow computation in scenes containing both complex volumetric objects and polyhedral models. Our system is the first hardware accelerated complete implementation of deep shadow maps, which unifies the computation of volumetric and geometric shadows. Up to now such unified computation was limited to software-only rendering . Previous hardware accelerated techniques can handle only geometric or only volumetric scenes - both resulting in the loss of important properties of the original concept. Our approach supports interactive rendering of polyhedrally bounded volumetric objects on the GPU based on ray casting. The ray casting can be conveniently used for both the shadow map computation and the rendering. We show how anti-aliased high-quality shadows are feasible in scenes composed of multiple overlapping translucent objects, and how sparse scenes can be handled efficiently using clustered deep shadow maps. © 2012 Springer-Verlag.

  18. PRECONDITIONS AND DETERMINING CAUSES OF THE SHADOW ECONOMY IN UKRAINE

    Directory of Open Access Journals (Sweden)

    Z. Varnalii

    2014-03-01

    Full Text Available The article analyzes the main processes that led to the high level of the economy shadowing. The historical aspects of the formation of the shadow economy in Ukraine are highlighted. The socio-economic aspects of the shadow economy of Ukraine causality are discussed. The theoretical contribution of foreign and domestic researchers on the preconditions of formation of the shadow economy in transition economies is studied. Theoretical perspective on the factors of the shadowing processes in the economy of Ukraine from the standpoint of modern scientific researches is analyzed. The paper also provides scientific vectors for further development of researches aimed at studying the causes and preconditions of the shadow economy.

  19. SHIELDS Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Jordanova, Vania Koleva [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-10-03

    Predicting variations in the near-Earth space environment that can lead to spacecraft damage and failure, i.e. “space weather”, remains a big space physics challenge. A new capability was developed at Los Alamos National Laboratory (LANL) to understand, model, and predict Space Hazards Induced near Earth by Large Dynamic Storms, the SHIELDS framework. This framework simulates the dynamics of the Surface Charging Environment (SCE), the hot (keV) electrons representing the source and seed populations for the radiation belts, on both macro- and micro-scale. In addition to using physics-based models (like RAM-SCB, BATS-R-US, and iPIC3D), new data assimilation techniques employing data from LANL instruments on the Van Allen Probes and geosynchronous satellites were developed. An order of magnitude improvement in the accuracy in the simulation of the spacecraft surface charging environment was thus obtained. SHIELDS also includes a post-processing tool designed to calculate the surface charging for specific spacecraft geometry using the Curvilinear Particle-In-Cell (CPIC) code and to evaluate anomalies' relation to SCE dynamics. Such diagnostics is critically important when performing forensic analyses of space-system failures.

  20. New Toroid shielding design

    CERN Multimedia

    Hedberg V

    On the 15th of June 2001 the EB approved a new conceptual design for the toroid shield. In the old design, shown in the left part of the figure above, the moderator part of the shielding (JTV) was situated both in the warm and cold areas of the forward toroid. It consisted both of rings of polyethylene and hundreds of blocks of polyethylene (or an epoxy resin) inside the toroid vacuum vessel. In the new design, shown to the right in the figure above, only the rings remain inside the toroid. To compensate for the loss of moderator in the toroid, the copper plug (JTT) has been reduced in radius so that a layer of borated polyethylene can be placed around it (see figure below). The new design gives significant cost-savings and is easier to produce in the tight time schedule of the forward toroid. Since the amount of copper is reduced the weight that has to be carried by the toroid is also reduced. Outgassing into the toroid vacuum was a potential problem in the old design and this is now avoided. The main ...

  1. Limitations of patterning thin films by shadow mask high vacuum chemical vapor deposition

    International Nuclear Information System (INIS)

    Reinke, Michael; Kuzminykh, Yury; Hoffmann, Patrik

    2014-01-01

    A key factor in engineering integrated devices such as electro-optic switches or waveguides is the patterning of high quality crystalline thin films into specific geometries. In this contribution high vacuum chemical vapor deposition (HV-CVD) was employed to grow titanium dioxide (TiO 2 ) patterns onto silicon. The directed nature of precursor transport – which originates from the high vacuum environment during the process – allows shading certain regions on the substrate by shadow masks and thus depositing patterned thin films. While the use of such masks is an emerging field in stencil or shadow mask lithography, their use for structuring thin films within HV-CVD has not been reported so far. The advantage of the employed technique is the precise control of lateral spacing and of the distance between shading mask and substrate surface which is achieved by manufacturing them directly on the substrate. As precursor transport takes place in the molecular flow regime, the precursor impinging rates (and therefore the film growth rates) on the surface can be simulated as function of the reactor and shading mask geometry using a comparatively simple mathematical model. In the current contribution such a mathematical model, which predicts impinging rates on plain or shadow mask structured substrates, is presented. Its validity is confirmed by TiO 2 -deposition on plain silicon substrates (450 °C) using titanium tetra isopropoxide as precursor. Limitations of the patterning process are investigated by the deposition of TiO 2 on structured substrates and subsequent shadow mask lift-off. The geometry of the deposits is according to the mathematical model. Shading effects due to the growing film enables to fabricate deposits with predetermined variations in topography and non-flat top deposits which are complicated to obtain by classical clean room processes. As a result of the enhanced residual pressure of decomposition products and titanium precursors and the

  2. Corruption and the shadow economy: a structural equation model approach

    OpenAIRE

    Buehn, Andreas; Schneider, Friedrich G.

    2009-01-01

    The relationship between corruption and the shadow economy is not clear. Theoretically, they either substitute or complement each other – exhibiting either a negative or positive relationship. This paper – using a structural equation model with two latent variables – extracts information on various dimensions of corruption and the shadow economy to contribute to the debate on their relationship. It presents empirical evidence of a positive relationship between the shadow economy and corruptio...

  3. A case of shadow flicker/flashing: assessment and solution

    International Nuclear Information System (INIS)

    Clarke, A.D.

    1991-01-01

    A short study was carried out investigating a reported problem of shadow flicker and flashing from the blades of a turbine. The incidence of this phenomenon was confirmed and the duration and frequency of occurrence assessed. The shadow flicker period would be short and only occur at certain times, but could cause irritation. A device to stop the turbine when shadow flicker occurred was recommended and is described. A recommendation was made that turbines should be sited at least ten diameters distance from habitations, and more if sited to the East/Southwest, and the shadow path identified. (author)

  4. Applications of a shadow camera system for energy meteorology

    Science.gov (United States)

    Kuhn, Pascal; Wilbert, Stefan; Prahl, Christoph; Garsche, Dominik; Schüler, David; Haase, Thomas; Ramirez, Lourdes; Zarzalejo, Luis; Meyer, Angela; Blanc, Philippe; Pitz-Paal, Robert

    2018-02-01

    Downward-facing shadow cameras might play a major role in future energy meteorology. Shadow cameras directly image shadows on the ground from an elevated position. They are used to validate other systems (e.g. all-sky imager based nowcasting systems, cloud speed sensors or satellite forecasts) and can potentially provide short term forecasts for solar power plants. Such forecasts are needed for electricity grids with high penetrations of renewable energy and can help to optimize plant operations. In this publication, two key applications of shadow cameras are briefly presented.

  5. Radiation shield for PWR reactors

    International Nuclear Information System (INIS)

    Esenov, Amra; Pustovgar, Andrey

    2013-01-01

    One of the chief structures of a reactor pit is a 'dry' shield. Setting up a 'dry' shield includes the technologically complex process of thermal processing of serpentinite concrete. Modern advances in the area of materials technology permit avoiding this complex and demanding procedure, and this significantly decreases the duration, labor intensity, and cost of setting it up. (orig.)

  6. In the shadow of their parents

    DEFF Research Database (Denmark)

    Bjerre, Line Søberg

    with the parents. In important ways, their discussions of families are informed by the traditions of social diagnosing, which have historically been informed by psychiatric and psychoanalytic thinking, particularly the notion of psychological determinism; the child’s perspective remains out of sight....... In this tradition, children are largely constructed as passive victims of the parents’ problems. With the child obscured in the shadow of the parents’ social diagnosis, it remains difficult to implement the intentions of legislation that seeks to foreground the child’s perspective. I conclude that if children...

  7. Shadow Banking y Liquidez en Colombia.

    OpenAIRE

    Pamela Cardozo; Jorge Cely; Andrés MUrcia

    2013-01-01

    En este estudio calculamos un indicador de la actividad de shadow banking en Colombia para el período comprendido entre enero de 2011 y marzo de 2013. Dicho indicador sugiere que esta actividad ha venido incrementándose y representa cerca del 9,9% del PIB de 2012. Adicionalmente, evaluamos el nivel de prociclicidad que puede tener la decisión de apalancamiento de un grupo de intermediarios financieros especialmente asociados a este tipo de actividad, encontrando que dicha prociclicidad está a...

  8. Quarkonium plus prompt photon and shadowing extraction

    Energy Technology Data Exchange (ETDEWEB)

    Machado, M.V.T., E-mail: magnus@if.ufrgs.br [Instituto de Fisica, Universidade Federal do Rio Grande do Sul, Porto Alegre, RS (Brazil); Brenner Mariotto, C., E-mail: mariotto@fisica.furg.br [Instituto de Matematica, Estatistica e Fisica (IMEF). Universidade Federal do Rio Grande (FURG), Rio Grande, RS (Brazil)

    2011-05-15

    In this contribution we investigate the influence of nuclear effects in hadroproduction of quarkonium associated with a photon. At high energies, such processes provide a probe of the QCD dynamics as it is dependent on the nuclear gluon distribution, and could be usefull in constraining the behavior of the nuclear gluon distribution in proton-nucleus and nucleus-nucleus collisions. Here we study the influence of the shadowing effect, in the production of J/{psi}(orY)+{gamma} at the LHC and estimate the p{sub T} dependence of the nuclear modification factors. The theoretical framework considered for quarkonium production is the non-relativistic QCD (NRQCD) factorization formalism.

  9. Welding shield for coupling heaters

    Science.gov (United States)

    Menotti, James Louis

    2010-03-09

    Systems for coupling end portions of two elongated heater portions and methods of using such systems to treat a subsurface formation are described herein. A system may include a holding system configured to hold end portions of the two elongated heater portions so that the end portions are abutted together or located near each other; a shield for enclosing the end portions, and one or more inert gas inlets configured to provide at least one inert gas to flush the system with inert gas during welding of the end portions. The shield may be configured to inhibit oxidation during welding that joins the end portions together. The shield may include a hinged door that, when closed, is configured to at least partially isolate the interior of the shield from the atmosphere. The hinged door, when open, is configured to allow access to the interior of the shield.

  10. Shield calculations, optimization vs. paradigm

    International Nuclear Information System (INIS)

    Cornejo D, N.; Hernandez S, A.; Martinez G, A.

    2006-01-01

    Many shieldings have been designed under the criteria of 'Maximum dose rates of project'. It has created the paradigm of those 'low dose rates', for the one which not few specialists would consider unacceptable levels of dose rate superior to the units of μSv.h -1 , independently of the exposure times. At the present time numerous shieldings are being designed considering dose restrictions in real times of exposure. After these new shieldings, the dose rates could be notably superior to those after traditional shieldings, without it implies inadequate designs or constructive errors. In the work significant differences in levels of dose rates and thickness of shieldings estimated by both methods for some typical facilities. It was concluded that the use of real times of exposure is more adequate for the optimization of the Radiological Protection, although this method demands bigger care in its application. (Author)

  11. Parameters calculation of shielding experiment

    International Nuclear Information System (INIS)

    Gavazza, S.

    1986-02-01

    The radiation transport methodology comparing the calculated reactions and dose rates for neutrons and gama-rays, with experimental measurements obtained on iron shield, irradiated in the YAYOI reactor is evaluated. The ENDF/B-IV and VITAMIN-C libraries and the AMPX-II modular system, for cross sections generation collapsed by the ANISN code were used. The transport calculations were made using the DOT 3.5 code, adjusting the boundary iron shield source spectrum to the reactions and dose rates, measured at the beginning of shield. The neutron and gamma ray distributions calculated on the iron shield presented reasonable agreement with experimental measurements. An experimental arrangement using the IEA-R1 reactor to determine a shielding benchmark is proposed. (Author) [pt

  12. Socket Shield Technique

    OpenAIRE

    Ferreira, João Eduardo Freitas

    2017-01-01

    Nos dias atuais, é cada vez mais comum a realização de extrações de dentes que estejam severamente comprometidos e substituí-los por implantes dentários. Após extração, existe uma reabsorção de osso alveolar que vai resultar numa perda de osso vertical e horizontal, tornando-se um dos fatores que subsequentemente se vai colocar como uma das maiores dificuldades na colocação de implantes. A técnica Socket Shield é uma técnica de preservação de osso alveolar em situações de implantes imediatos,...

  13. Shielded Canister Transporter

    International Nuclear Information System (INIS)

    Eidem, G.G. Jr.; Fages, R.

    1993-01-01

    The Hanford Waste Vitrification Plant (HWVP) will produce canisters filled with high-level radioactive waste immobilized in borosilicate glass. This report discusses a Shielded Canister Transporter (SCT) which will provide the means for safe transportation and handling of the canisters from the Vitrification Building to the Canister Storage Building (CSB). The stainless steel canisters are 0.61 meters in diameter, 3.0 meters tall, and weigh approximately 2,135 kilograms, with a maximum exterior surface dose rate of 90,000 R/hr. The canisters are placed into storage tubes to a maximum of three tall (two for overpack canisters) with an impact limiter placed at the tube bottom and between each canister. A floor plug seals the top of the storage tube at the operating floor level of the CSB

  14. Computational shielding benchmarks

    International Nuclear Information System (INIS)

    The American Nuclear Society Standards Committee 6.2.1 is engaged in the documentation of radiation transport problems and their solutions. The primary objective of this effort is to test computational methods used within the international shielding community. Dissemination of benchmarks will, it is hoped, accomplish several goals: (1) Focus attention on problems whose solutions represent state-of-the-art methodology for representative transport problems of generic interest; (2) Specification of standard problems makes comparisons of alternate computational methods, including use of approximate vs. ''exact'' computer codes, more meaningful; (3) Comparison with experimental data may suggest improvements in computer codes and/or associated data sets; (4) Test reliability of new methods as they are introduced for the solution of specific problems; (5) Verify user ability to apply a given computational method; and (6) Verify status of a computer program being converted for use on a different computer (e.g., CDC vs IBM) or facility

  15. Control rod shadowing and anti-shadowing effects in a large gas-cooled fast reactor

    International Nuclear Information System (INIS)

    Girardin, G.; Chawla, R.; Rimpault, G.; Coddington, P.

    2007-01-01

    An investigation of control rod shadowing and anti-shadowing (interaction) effects has been carried out in the context of a design study of the control rod pattern for the large 2400 MWth Generation IV Gas-cooled Fast Reactor (GFR). For the calculations, the deterministic code system ERANOS-2.0 has been used, in association with a full core model including a European Fast Reactor (EFR)-type pattern for the control rods. More specifically, the core contains a total of 33 control (CSD) and safety (DSD) rods implemented in three banks: -1) a first bank of 6 CSD rods, placed at 64 cm from core centre in the inner fuel zone (Pu content 16.3 % vol.), -2) a safety bank consisting of 9 DSD rods, at an average distance of 118 cm, and -3) a third bank with 18 CSD rods, placed at 171 cm, i.e. at the interface between the inner and outer (Pu content 19.2 % vol.) core regions. Each control rod has been modelled as a homogeneous material containing 90%-enriched B 4 C, steel and helium. Considerable shadowing effects have been observed between the first bank and the safety bank, as also between individual rods within the first bank. Large anti-shadowing effects take place in an even greater number of the studied rod configurations. The largest interaction is between the two CSD banks, the anti-shadowing value being 46% in this case, implying that the total rod worth is increased by a factor of almost 2 when compared to the sum of the individual bank values. Additional investigations have been performed, in particular the computation of the first order eigenvalue and the eigenvalue separation. The main finding is that the interactions are lower when one of the control rod banks is located at a radial position corresponding to half the core radius. (authors)

  16. Ovarian Basaloid Carcinoma with Shadow Cell Differentiation

    Directory of Open Access Journals (Sweden)

    Michal Zamecnik

    2014-01-01

    Full Text Available So-called shadow cell differentiation (SCD is typical for pilomatrixoma and other skin lesions with follicular differentiation, but it was rarely described also in some visceral carcinomas. We report a case of ovarian basaloid carcinoma with SCD. The tumor presented as a 14 cm ovarian mass in a 45-year-old woman, and therefore the adnexectomy and hysterectomy were performed. The tumor was of high stage. Multiple metastases were found in the liver, retroperitoneal and mediastinal lymph nodes, and the lung. Histologically, the tumor showed a pattern of high-grade basaloid carcinoma with numerous shadow cells. Extensive histologic examination did not reveal any glandular or preexisting teratoma component. Immunohistochemically, the tumor expressed markers of squamous cell differentiation, such as p63, cytokeratin 5/6, and high-molecular-weight keratin. Cytokeratin 7 and CA125 were positive in scattered cells of the lesion. Estrogen and progesterone receptor, vimentin, and p53 were negative. Beta-catenin showed nuclear and cytoplasmic positivity, indicating possible tumor proliferation/differentiation via Wnt signaling pathway. To our knowledge, SCD in basaloid carcinoma of the ovary was not described before. In addition to the description of the case, we review the literature on SCD in visceral carcinomas.

  17. Model planetary nebulae: the effect of shadowed filaments on low ionization potential ion radiation

    International Nuclear Information System (INIS)

    Katz, A.

    1977-01-01

    Previous homogeneous model planetary nebulae calculations No. 4 have yielded emission strengths for low ionization potential No. 4 ions which are considerably lower than those observed. Several attempts were to correct this problem by the inclusion of optically thin condensations, the use of energy flux distributions from stellar model calculations instead of blackbody spectrum stars, and the inclusion of dust in the nebulae. The effect that shadowed filaments have on the ionization and thermal structure of model nebulae and the resultant line strengths are considered. These radial filaments are shielded from the direct stellar ionizing radiation by optically thick condensations in the nebula. Theoretical observational evidence exists for the presence of condensations and filaments. Since the only source of ionizing photons in the shadowed filaments is due to diffuse photons produced by recombination, ions of lower ionization potential are expected to exist there in greater numbers than those found in the rest of the nebula. This leads to increased line strengths from these ions and increases their values to match the observational values. It is shown that these line strengths in the filaments increase by over one to two orders of magnitude relative to values found in homogeneous models. This results in an increase of approximately one order of magnitude for these lines when contributions from both components of the nebula are considered. The parameters that determine the exact value of the increase are the radial location of the filaments in the nebula and the fraction of the nebular volume occupied by the filaments

  18. An example of a vector field with the oriented shadowing property

    OpenAIRE

    Tikhomirov, Sergey

    2014-01-01

    We consider shadowing properties for vector fields corresponding to different type of reparametrisations. We give an example of a vector field which has the oriented shadowing properties, but does not have the standard shadowing property.

  19. Radiation shielding for fusion reactors

    International Nuclear Information System (INIS)

    Santoro, R.T.

    2000-01-01

    Radiation shielding requirements for fusion reactors present different problems than those for fission reactors and accelerators. Fusion devices, particularly tokamak reactors, are complicated by geometry constraints that complicate disposition of fully effective shielding. This paper reviews some of these shielding issues and suggested solutions for optimizing the machine and biological shielding. Radiation transport calculations are essential for predicting and confirming the nuclear performance of the reactor and, as such, must be an essential part of the reactor design process. Development and optimization of reactor components from the first wall and primary shielding to the penetrations and containment shielding must be carried out in a sensible progression. Initial results from one-dimensional transport calculations are used for scoping studies and are followed by detailed two- and three-dimensional analyses to effectively characterize the overall radiation environment. These detail model calculations are essential for accounting for the radiation leakage through ports and other penetrations in the bulk shield. Careful analysis of component activation and radiation damage is cardinal for defining remote handling requirements, in-situ replacement of components, and personnel access at specific locations inside the reactor containment vessel. (author)

  20. Lunar Surface Reactor Shielding Study

    International Nuclear Information System (INIS)

    Kang, Shawn; McAlpine, William; Lipinski, Ronald

    2006-01-01

    A nuclear reactor system could provide power to support long term human exploration of the moon. Such a system would require shielding to protect astronauts from its emitted radiations. Shielding studies have been performed for a Gas Cooled Reactor system because it is considered to be the most suitable nuclear reactor system available for lunar exploration, based on its tolerance of oxidizing lunar regolith and its good conversion efficiency. The goals of the shielding studies were to determine a material shielding configuration that reduces the dose (rem) to the required level in order to protect astronauts, and to estimate the mass of regolith that would provide an equivalent protective effect if it were used as the shielding material. All calculations were performed using MCNPX, a Monte Carlo transport code. Lithium hydride must be kept between 600 K and 700 K to prevent excessive swelling from large amounts of gamma or neutron irradiation. The issue is that radiation damage causes separation of the lithium and the hydrogen, resulting in lithium metal and hydrogen gas. The proposed design uses a layer of B4C to reduce the combined neutron and gamma dose to below 0.5Grads before the LiH is introduced. Below 0.5Grads the swelling in LiH is small (less than about 1%) for all temperatures. This approach causes the shield to be heavier than if the B4C were replaced by LiH, but it makes the shield much more robust and reliable

  1. Shadow Enhancement in Synthetic Aperture Sonar Using Fixed Focusing

    NARCIS (Netherlands)

    Groen, J.; Hansen, R.E.; Callow, H.J.; Sabel, J.C.; Sæbø, T.O.

    2009-01-01

    Abstract—A shadow cast by an object on the seafloor is important information for target recognition in synthetic aperture sonar (SAS) images. Synthetic aperture imaging causes a fundamental limitation to shadow clarity because the illuminator is moved during the data collection. This leads to a

  2. Shading and shadowing on Canaletto's Piazza San Marco

    NARCIS (Netherlands)

    Wijntjes, M.W.A.; De Ridder, H.

    2014-01-01

    Whereas the 17th century painter Canaletto was a master in linear perspective of the architectural elements, he seems to have had considerable difficulty with linear perspective of shadows. A common trick to avoid shadow perspective problems is to set the (solar) illumination direction parallel to

  3. Reusable High Aspect Ratio 3-D Nickel Shadow Mask

    Science.gov (United States)

    Shandhi, M.M.H.; Leber, M.; Hogan, A.; Warren, D.J.; Bhandari, R.; Negi, S.

    2017-01-01

    Shadow Mask technology has been used over the years for resistless patterning and to pattern on unconventional surfaces, fragile substrate and biomaterial. In this work, we are presenting a novel method to fabricate high aspect ratio (15:1) three-dimensional (3D) Nickel (Ni) shadow mask with vertical pattern length and width of 1.2 mm and 40 μm respectively. The Ni shadow mask is 1.5 mm tall and 100 μm wide at the base. The aspect ratio of the shadow mask is 15. Ni shadow mask is mechanically robust and hence easy to handle. It is also reusable and used to pattern the sidewalls of unconventional and complex 3D geometries such as microneedles or neural electrodes (such as the Utah array). The standard Utah array has 100 active sites at the tip of the shaft. Using the proposed high aspect ratio Ni shadow mask, the Utah array can accommodate 300 active sites, 200 of which will be along and around the shaft. The robust Ni shadow mask is fabricated using laser patterning and electroplating techniques. The use of Ni 3D shadow mask will lower the fabrication cost, complexity and time for patterning out-of-plane structures. PMID:29056835

  4. Shadow edge detection using geometric and photometric features

    NARCIS (Netherlands)

    Gijsenij, A.; Gevers, T.

    2009-01-01

    The detection of shadow and shading edges is a first step towards reducing the imaging effects that are caused by interactions of the light source with surfaces that are in the scene. As most of the algorithms for shadow edge detection use photometric information, geometric information have been

  5. Shadows of Einstein–dilaton–Gauss–Bonnet black holes

    Energy Technology Data Exchange (ETDEWEB)

    Cunha, Pedro V.P., E-mail: pintodacunha@tecnico.ulisboa.pt [Departamento de Física da Universidade de Aveiro and Centre for Research and Development in Mathematics and Applications (CIDMA), Campus de Santiago, 3810-183 Aveiro (Portugal); CENTRA, Departamento de Física, Instituto Superior Técnico, Universidade de Lisboa, Avenida Rovisco Pais 1, 1049, Lisboa (Portugal); Herdeiro, Carlos A.R., E-mail: herdeiro@ua.pt [Departamento de Física da Universidade de Aveiro and Centre for Research and Development in Mathematics and Applications (CIDMA), Campus de Santiago, 3810-183 Aveiro (Portugal); Kleihaus, Burkhard, E-mail: b.kleihaus@uni-oldenburg.de [Institute of Physics, University of Oldenburg, Oldenburg, 26111 (Germany); Kunz, Jutta, E-mail: jutta.kunz@uni-oldenburg.de [Institute of Physics, University of Oldenburg, Oldenburg, 26111 (Germany); Radu, Eugen, E-mail: eugen.radu@ua.pt [Departamento de Física da Universidade de Aveiro and Centre for Research and Development in Mathematics and Applications (CIDMA), Campus de Santiago, 3810-183 Aveiro (Portugal)

    2017-05-10

    We study the shadows of the fully non-linear, asymptotically flat Einstein–dilaton–Gauss–Bonnet (EdGB) black holes (BHs), for both static and rotating solutions. We find that, in all cases, these shadows are smaller than for comparable Kerr BHs, i.e. with the same total mass and angular momentum under similar observation conditions. In order to compare both cases we provide quantitative shadow parameters, observing in particular that the differences in the shadows mean radii are never larger than the percent level. Therefore, generically, EdGB BHs cannot be excluded by (near future) shadow observations alone. On the theoretical side, we find no clear signature of some exotic features of EdGB BHs on the corresponding shadows, such as the regions of negative (Komar, say) energy density outside the horizon. We speculate that this is due to the fact that the Komar energy interior to the light rings (or more precisely, the surfaces of constant radial coordinate that intersect the light rings in the equatorial plane) is always smaller than the ADM mass, and consequently the corresponding shadows are smaller than those of comparable Kerr BHs. The analysis herein provides a clear example that it is the light ring impact parameter, rather than its “size”, that determines a BH shadow.

  6. Radiation shielding in dental radiography.

    Science.gov (United States)

    Stenström, B; Rehnmark-Larsson, S; Julin, P; Richter, S

    1983-01-01

    The protective effect in the thyroid region from different types of radiation shielding at intraoral radiography has been studied as well as the reduction of the absorbed dose to the sternal and the gonadal regions. The shielding tested were the different types of leaded aprons, of which three had an attached leaded collar and the other two were used in combination with separate soft leaded collars. Furthermore one of the soft leaded collars and an unflexible horizontal leaded shield were tested separately. Two dental x-ray machines of 60 and 65 kVp with rectangular and circular tube collimators were used. The exposure times corresponded to speed group E film. The absorbed doses were measured with two ionization chambers. No significant difference in the protective effect in the thyroid gland could be found between the different types of radiation shieldings. There was a dose reduction by approximately a factor of 2 to the thyroid region down to 0.08 mGy per full survey using parallelling technique, and below 0.001 mGy per single bitewing exposure. The shielding reduced the thyroid dose using bisecting-angle technique by a factor of 5 down to 0.15 mGy per full survey (20 exposures). In the sternal region the combinations of apron and collar reduced the absorbed dose from a full survey to below 2 microGy compared with 18 microGy (parallelling) and 31 microGy (bisecting-angle) without any shielding. With the horizontal leaded shield a reduction by a factor of 6 was obtained, but no significant sternal dose reduction could be detected from the soft collar alone. The gonadal dose could be reduced by a factor of 10 with the horizontal leaded shield, parallelling technique and circular collimator. Using leaded aprons the gonadal was approximately one per cent of the dose without any shielding, i.e. below 0.01 microGy per single intraoral exposure.

  7. Radiation shielding in dental radiography

    Energy Technology Data Exchange (ETDEWEB)

    Stenstroem, B.; Rehnmark-Larsson, S.; Julin, P.; Richter, S.

    1983-01-01

    The protective effect in the thyroid region from different types of radiation shieldings at intraoral radiography has been studied as well as the reduction of the absorbed dose to the sternal and the gonadal regions. The shieldings tested were five different types of leaded aprons, of which three had an attached leaded collar and the other two were used in combination with separate soft leaded collars. Furthermore one of the soft leaded collars and an unflexible horizontal leaded shield were tested separately. Two dental x-ray machines of 60 and 65 kVp with rectangular and circular tube collimators were used. The exposure time corresponded to speed group E film. The absorbed doses were measured with two ionization chambers. No significant difference in the protective effect in the thyroid gland could be found between the different types of radiation shieldings. There was a dose reduction by approximately a factor of 2 to the thyroid region down to 0.08 mGy per full survey using parallelling technique, and below 0.001 mGy per single bitewing exposure. The shieldings reduced the thyroid dose using bisecting-angle technique by a factor of 5 down to 0.15 mGy per full survey (20 exposures). In the sternal region the combinations of apron and collar reduced the absorbed dose from a full survey to below 2 ..mu..Gy compared with 18 ..mu..Gy (parallelling) and 31 ..mu..Gy (biscting-angle) without any shielding. With the horizontal leaded shield a reduction by a factor of 6 was obtained but no significant sternal dose reduction could be detected from the soft collar alone. The gonadal dose could be reduced by a factor of 10 with the horizontal leaded shield, parallelling technique and circular collimator. Using leaded aprons the gonadal dose was approximately one per cent of the dose without any shielding, i.e. below 0.01 ..mu..Gy per single intraoral exposure.

  8. Radiation shielding in dental radiography

    Energy Technology Data Exchange (ETDEWEB)

    Stenstroem, B.; Rehnmark-Larsson, S.; Julin, P.; Richter, S.

    1984-01-01

    The protective effect in the thyroid region from different types of radiation shieldings at intraoral radiography has been studied as well as the reduction of the absorbed dose to the sternal and the gonadal regions. The shieldings tested were five different types of leaded aprons, of which three had an attached leaded collar and the other two were used in combination with separate soft leaded collars. Furthermore one of the soft leaded collars and an unflexible horizontal leaded shield were tested separately. Two dental x-ray machines of 60 and 65 kVp with rectangular and circular tube collimators were used. The exposure time corresponded to speed group E film. The absorbed doses were measured with two ionization chambers. No significant difference in the protective effect in the thyroid gland could be found between the different types of radiation shieldings. There was a dose reduction by approximately a factor of 2 to the thyroid region down to 0.08 mGy per full survey using parallelling technique, and below 0.001 mGy per single bitewing exposure. The shieldings reduced the thyroid dose using bisecting-angle technique by a factor of 5 down to 0.15 mGy per full survey. In the sternal region the combinations of apron and collar reduced the absorbed dose from a full survey to below 2 ..mu..Gy compared with 18 ..mu..Gy (parallelling) and 31 ..mu..Gy (biscting-angle) without any shielding. With the horizontal leaded shield a reduction by a factor of 6 was obtained but no significant sternal dose reduction could be detected from the soft collar alone. The gonadal dose could be reduced by a factor of 10 with the horizontal leaded shield, parallelling technique and circular collimator. Using leaded aprons the gonadal dose was approximately one per cent of the dose without any shielding, i.e. below 0.01 ..mu..Gy per single intraoral exposure.

  9. Morphometry of terrestrial shield volcanoes

    Science.gov (United States)

    Grosse, Pablo; Kervyn, Matthieu

    2018-03-01

    Shield volcanoes are described as low-angle edifices built primarily by the accumulation of successive lava flows. This generic view of shield volcano morphology is based on a limited number of monogenetic shields from Iceland and Mexico, and a small set of large oceanic islands (Hawaii, Galápagos). Here, the morphometry of 158 monogenetic and polygenetic shield volcanoes is analyzed quantitatively from 90-meter resolution SRTM DEMs using the MORVOLC algorithm. An additional set of 24 lava-dominated 'shield-like' volcanoes, considered so far as stratovolcanoes, are documented for comparison. Results show that there is a large variation in shield size (volumes from 0.1 to > 1000 km3), profile shape (height/basal width (H/WB) ratios mostly from 0.01 to 0.1), flank slope gradients (average slopes mostly from 1° to 15°), elongation and summit truncation. Although there is no clear-cut morphometric difference between shield volcanoes and stratovolcanoes, an approximate threshold can be drawn at 12° average slope and 0.10 H/WB ratio. Principal component analysis of the obtained database enables to identify four key morphometric descriptors: size, steepness, plan shape and truncation. Hierarchical cluster analysis of these descriptors results in 12 end-member shield types, with intermediate cases defining a continuum of morphologies. The shield types can be linked in terms of growth stages and shape evolution, related to (1) magma composition and rheology, effusion rate and lava/pyroclast ratio, which will condition edifice steepness; (2) spatial distribution of vents, in turn related to the magmatic feeding system and the tectonic framework, which will control edifice plan shape; and (3) caldera formation, which will condition edifice truncation.

  10. Politics, Time and Space in the Era of Shadow Banking

    DEFF Research Database (Denmark)

    Bryan, Dick; Rafferty, Michael; Wigan, Duncan

    2016-01-01

    In the wake of the Global Financial Crisis, there has been an understandable focus on the financial fragility and contagion aspects of shadow banking. This article argues that shadow banking is important for another set of reasons. It has been well established that shadow banking permits...... challenging earlier spatio-temporal concepts of finance, and the regulatory/jurisdictional order built on them. The article suggests that the longer term significance of shadow banking may not just be its role in financial crisis, or even tax and regulatory arbitrage, but that it was here that innovative...... the transformation of assets and financial claims. It has also been established that fiscal and regulatory arbitrage occurs through shadow banking, and associated offshore financial activities. The article develops the argument that together these are transforming the times and spaces of modern finance, and directly...

  11. Shielding around spallation neutron sources

    International Nuclear Information System (INIS)

    Fragopoulou, M; Manolopoulou, M; Stoulos, S; Brandt, R; Westmeier, W; Krivopustov, M; Sosnin, A; Golovatyuk, S; Zamani, M

    2006-01-01

    Spallation neutron sources provide more intense and harder neutron spectrum than nuclear reactors for which a substantial amount of shielding measurements have been performed. Although the main part of the cost for a spallation station is the cost of the shielding, measurements regarding shielding for the high energy neutron region are still very scarce. In this work calculation of the neutron interaction length in polyethylene moderator for different neutron energies is presented. Measurements which were carried out in Nuclotron accelerator at the Laboratory of High Energies (Joint Institute for Nuclear Research, Dubna) and comparison with calculation are also presented. The measurements were performed with Solid State Nuclear Track Detectors (SSNTDs)

  12. Radiation protection/shield design

    International Nuclear Information System (INIS)

    Disney, R.K.

    1977-01-01

    Radiation protection/shielding design of a nuclear facility requires a coordinated effort of many engineering disciplines to meet the requirements imposed by regulations. In the following discussion, the system approach to Clinch River Breeder Reactor Plant (CRBRP) radiation protection will be described, and the program developed to implement this approach will be defined. In addition, the principal shielding design problems of LMFBR nuclear reactor systems will be discussed in realtion to LWR nuclear reactor system shielding designs. The methodology used to analyze these problems in the U.S. LMFBR program, the resultant design solutions, and the experimental verification of these designs and/or methods will be discussed. (orig.) [de

  13. Survivor shielding. Part C. Improvements in terrain shielding

    International Nuclear Information System (INIS)

    Egbert, Stephen D.; Kaul, Dean C.; Roberts, James A.; Kerr, George D.

    2005-01-01

    A number of atomic-bomb survivors were affected by shielding provided by terrain features. These terrain features can be a small hill, affecting one or two houses, or a high mountain that shields large neighborhoods. In the survivor dosimetry system, terrain shielding can be described by a transmission factor (TF), which is the ratio between the dose with and without the terrain present. The terrain TF typically ranges between 0.1 and 1.0. After DS86 was implemented at RERF, the terrain shielding categories were examined and found to either have a bias or an excessive uncertainty that could readily be removed. In 1989, an improvement in the terrain model was implemented at RERF in the revised DS86 code, but the documentation was not published. It is now presented in this section. The solution to the terrain shielding in front of a house is described in this section. The problem of terrain shielding of survivors behind Hijiyama mountain at Hiroshima and Konpirasan mountain at Nagasaki has also been recognized, and a solution to this problem has been included in DS02. (author)

  14. Simple machines

    CERN Document Server

    Graybill, George

    2007-01-01

    Just how simple are simple machines? With our ready-to-use resource, they are simple to teach and easy to learn! Chocked full of information and activities, we begin with a look at force, motion and work, and examples of simple machines in daily life are given. With this background, we move on to different kinds of simple machines including: Levers, Inclined Planes, Wedges, Screws, Pulleys, and Wheels and Axles. An exploration of some compound machines follows, such as the can opener. Our resource is a real time-saver as all the reading passages, student activities are provided. Presented in s

  15. Design and optimization of HPLWR high pressure Turbine gamma ray shield

    Energy Technology Data Exchange (ETDEWEB)

    Kebwaro, Jeremiah Monari; Zhao, Yaolin, E-mail: zhaoyaolin@mail.xjtu.edu.cn; He, Chaohui

    2015-04-01

    Highlights: • Shield around HPLWR high pressure turbine optimized by Monte Carlo method. • The occupancy period in the turbine building was considered in the optimization. • Shield thickness is significantly reduced when heavy concretes are used. • Shield thickness for BWRs is sufficient for HPWR if heavy concrete is used. - Abstract: This work proposes the optimum gamma ray shield thickness around the HPLWR high pressure turbine for different occupancy periods in the turbine building. Monte Carlo method was employed in the design process and only radioactive nitrogen-16 was considered as the source of radiation. Five grades of concrete (ordinary, magnetite, heavy magnetite, steel magnetite and barite) were used as shielding materials. The isotope source term in the high pressure turbine was estimated by modeling the HPLWR three pass core in MCNP and tracking the inventory using a simple algorithm. The high pressure turbine was thereafter modeled in MCNP with a concrete shield arrayed in layers around it. The surface flux tally and ICRP74 dose conversion coefficients were employed to estimate the dose profile across the shield. For some shielding materials, exponential functions were fitted on the calculated data to extrapolate dose values beyond the model thickness. The optimum shield thickness was determined by comparing the calculated dose profiles with dose limit proposals in the IAEA standard (NS-G-1.13) on radiation protection considerations during nuclear power plant design. It was observed that with a 120 cm thick heavy concrete shield, the turbine building would be safe for most occupancy periods. However for ordinary concrete the shield would require some extension to guarantee safety. For very long occupancy (more than 10 person hours per week), magnetite shield may also require slight extension. It can therefore be concluded that the shield thickness recommended for BWR turbines (which operate on a direct cycle like HPLWR) could be sufficient

  16. Radiation shielding member

    International Nuclear Information System (INIS)

    Nemezawa, Isao; Kimura, Tadahiro; Mizuochi, Akira; Omori, Tetsu

    1998-01-01

    A single body of a radiation shield comprises a bag prepared by welding or bonding a polyurethane sheet which is made flat while interposing metal plates at the upper and the lower portion of the bag. Eyelet fittings are disposed to the upper and the lower portions of the bag passing through the metal plates and the flat portion of the bag. Water supplying/draining ports are disposed to two upper and lower places of the bag at a height where the metal plates are disposed. Reinforcing walls welded or bonded to the inner wall surface of the bag are elongated in vertical direction to divide the inside of the bag to a plurality of cells. The bag is suspended and supported from a frame with S-shaped hooks inserted into the eyelet fittings as connecting means. A plurality of bags are suspended and supported from the frame at a required height by way of the eyelets at the lower portion of the suspended and supported bag and the eyelet fittings at the upper portion of the bag below the intermediate connection means. (I.N.)

  17. K Coverage Probability of 5G Wireless Cognitive Radio Network under Shadow Fading Effects

    Directory of Open Access Journals (Sweden)

    Ankur S. Kang

    2016-09-01

    Full Text Available Land mobile communication is burdened with typical propagation constraints due to the channel characteristics in radio systems.Also,the propagation characteristics vary form place to place and also as the mobile unit moves,from time to time.Hence,the tramsmission path between transmitter and receiver varies from simple direct LOS to the one which is severely obstructed by buildings,foliage and terrain.Multipath propagation and shadow fading effects affect the signal strength of an arbitrary Transmitter-Receiver due to the rapid fluctuations in the phase and amplitude of signal which also determines the average power over an area of tens or hundreds of meters.Shadowing introduces additional fluctuations,so the received local mean power varies around the area –mean.The present section deals with the performance analysis of fifth generation wireless cognitive radio network on the basis of signal and interference level based k coverage probability under the shadow fading effects.

  18. Active Radiation Shield, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — DEC-Shield technology offers the means to generate electric power from cosmic radiation sources and fuse dissimilar systems and functionality into a structural...

  19. Shielding calculations. Optimization vs. Paradigms

    International Nuclear Information System (INIS)

    Cornejo Diaz, Nestor; Hernandez Saiz, Alejandro; Martinez Gonzalez, Alina

    2005-01-01

    Many radiation shielding barriers in Cuba have been designed according to the criterion of Maxi-mum Projected Dose Rates. This fact has created the paradigm of low dose rates. Because of this, dose rate levels greater than units of Sv.h-1 would be considered unacceptable by many specialists, regardless of the real exposure times. Nowadays many shielding barriers are being designed using dose constraints in real exposure times. Behind the new barriers, dose rates could be notably greater than those behind the traditional ones, and it does not imply inadequate designs or constructive errors. In this work were obtained significant differences in dose rate levels and shield-ing thicknesses calculated by both methods for some typical installations. The work concludes that real exposure time approach is more adequate in order to optimise Radiation Protection, although this method should be carefully applied

  20. Modelling the electrical properties of concrete for shielding effectiveness prediction

    International Nuclear Information System (INIS)

    Sandrolini, L; Reggiani, U; Ogunsola, A

    2007-01-01

    Concrete is a porous, heterogeneous material whose abundant use in numerous applications demands a detailed understanding of its electrical properties. Besides experimental measurements, material theoretical models can be useful to investigate its behaviour with respect to frequency, moisture content or other factors. These models can be used in electromagnetic compatibility (EMC) to predict the shielding effectiveness of a concrete structure against external electromagnetic waves. This paper presents the development of a dispersive material model for concrete out of experimental measurement data to take account of the frequency dependence of concrete's electrical properties. The model is implemented into a numerical simulator and compared with the classical transmission-line approach in shielding effectiveness calculations of simple concrete walls of different moisture content. The comparative results show good agreement in all cases; a possible relation between shielding effectiveness and the electrical properties of concrete and the limits of the proposed model are discussed

  1. Modelling the electrical properties of concrete for shielding effectiveness prediction

    Science.gov (United States)

    Sandrolini, L.; Reggiani, U.; Ogunsola, A.

    2007-09-01

    Concrete is a porous, heterogeneous material whose abundant use in numerous applications demands a detailed understanding of its electrical properties. Besides experimental measurements, material theoretical models can be useful to investigate its behaviour with respect to frequency, moisture content or other factors. These models can be used in electromagnetic compatibility (EMC) to predict the shielding effectiveness of a concrete structure against external electromagnetic waves. This paper presents the development of a dispersive material model for concrete out of experimental measurement data to take account of the frequency dependence of concrete's electrical properties. The model is implemented into a numerical simulator and compared with the classical transmission-line approach in shielding effectiveness calculations of simple concrete walls of different moisture content. The comparative results show good agreement in all cases; a possible relation between shielding effectiveness and the electrical properties of concrete and the limits of the proposed model are discussed.

  2. Measuring space radiation shielding effectiveness

    Directory of Open Access Journals (Sweden)

    Bahadori Amir

    2017-01-01

    Full Text Available Passive radiation shielding is one strategy to mitigate the problem of space radiation exposure. While space vehicles are constructed largely of aluminum, polyethylene has been demonstrated to have superior shielding characteristics for both galactic cosmic rays and solar particle events due to the high hydrogen content. A method to calculate the shielding effectiveness of a material relative to reference material from Bragg peak measurements performed using energetic heavy charged particles is described. Using accelerated alpha particles at the National Aeronautics and Space Administration Space Radiation Laboratory at Brookhaven National Laboratory, the method is applied to sample tiles from the Heat Melt Compactor, which were created by melting material from a simulated astronaut waste stream, consisting of materials such as trash and unconsumed food. The shielding effectiveness calculated from measurements of the Heat Melt Compactor sample tiles is about 10% less than the shielding effectiveness of polyethylene. Shielding material produced from the astronaut waste stream in the form of Heat Melt Compactor tiles is therefore found to be an attractive solution for protection against space radiation.

  3. Measuring space radiation shielding effectiveness

    Science.gov (United States)

    Bahadori, Amir; Semones, Edward; Ewert, Michael; Broyan, James; Walker, Steven

    2017-09-01

    Passive radiation shielding is one strategy to mitigate the problem of space radiation exposure. While space vehicles are constructed largely of aluminum, polyethylene has been demonstrated to have superior shielding characteristics for both galactic cosmic rays and solar particle events due to the high hydrogen content. A method to calculate the shielding effectiveness of a material relative to reference material from Bragg peak measurements performed using energetic heavy charged particles is described. Using accelerated alpha particles at the National Aeronautics and Space Administration Space Radiation Laboratory at Brookhaven National Laboratory, the method is applied to sample tiles from the Heat Melt Compactor, which were created by melting material from a simulated astronaut waste stream, consisting of materials such as trash and unconsumed food. The shielding effectiveness calculated from measurements of the Heat Melt Compactor sample tiles is about 10% less than the shielding effectiveness of polyethylene. Shielding material produced from the astronaut waste stream in the form of Heat Melt Compactor tiles is therefore found to be an attractive solution for protection against space radiation.

  4. Geomechanical effects of stress shadow created by large-scale destress blasting

    Directory of Open Access Journals (Sweden)

    Isaac Vennes

    2017-12-01

    Full Text Available This study aims to determine if large-scale choked panel destress blasting can provide sufficient beneficial stress reduction in highly-stressed remnant ore pillar that is planned for production. The orebody is divided into 20 stopes over 2 levels, and 2 panels are choke-blasted in the hanging wall to shield the ore pillar by creating a stress shadow around it. A linear-elastic model of the mining system is constructed with finite difference code FLAC3D. The effect of destress blasting in the panels is simulated by applying a fragmentation factor (α to the rock mass stiffness and a stress reduction factor (β to the current state of stress in the region occupied by the destress panels. As an extreme case, the destress panel is also modeled as a void to obtain the maximum possible beneficial effects of destressing and stress shadow. Four stopes are mined in the stress shadow of the panels in 6 lifts and then backfilled. The effect of destress blasting on the remnant ore pillar is quantified based on stress change and brittle shear ratio (BSR in the stress shadow zone compared to the base case without destress blasting. To establish realistic rock fragmentation and stress reduction factors, model results are compared to measured stress changes reported for case studies at Fraser and Brunswick mines. A 1.5 MPa immediate stress decrease was observed 20 m away from the panel at Fraser Mine, and a 4 MPa immediate stress decrease was observed 25 m away at Brunswick Mine. Comparable results are obtained from the current model with a rock fragmentation factor α of 0.2 and a stress reduction factor β of 0.8. It is shown that a destress blasting with these parameters reduces the major principal stress in the nearest stopes by 10–25 MPa. This yields an immediate reduction of BSR, which is deemed sufficient to reduce volume of ore at risk in the pillar.

  5. The inclusion of shadowing effect in the reaction-rates calculation

    International Nuclear Information System (INIS)

    Monteiro, M.A.M.

    1990-03-01

    A method for the Resonance Integral calculation in the fuel and moderator regions is presented including the Shadowing effect. This effect appears due to the presence of several fuel rods in a infinite moderator region. The method is based on the approximations to the J (ζ, β) function and theirs partial derivatives in relation to β. The dependence of the Resonance Integral in the J (ζ, β) comes from the rational approximation to the neutron escape probability. The final results are obtained in a very simple and fast way, and show the good accuracy of the method. (author)

  6. Modelling and Optimization of Four-Segment Shielding Coils of Current Transformers.

    Science.gov (United States)

    Gao, Yucheng; Zhao, Wei; Wang, Qing; Qu, Kaifeng; Li, He; Shao, Haiming; Huang, Songling

    2017-05-26

    Applying shielding coils is a practical way to protect current transformers (CTs) for large-capacity generators from the intensive magnetic interference produced by adjacent bus-bars. The aim of this study is to build a simple analytical model for the shielding coils, from which the optimization of the shielding coils can be calculated effectively. Based on an existing stray flux model, a new analytical model for the leakage flux of partial coils is presented, and finite element method-based simulations are carried out to develop empirical equations for the core-pickup factors of the models. Using the flux models, a model of the common four-segment shielding coils is derived. Furthermore, a theoretical analysis is carried out on the optimal performance of the four-segment shielding coils in a typical six-bus-bars scenario. It turns out that the "all parallel" shielding coils with a 45° starting position have the best shielding performance, whereas the "separated loop" shielding coils with a 0° starting position feature the lowest heating value. Physical experiments were performed, which verified all the models and the conclusions proposed in the paper. In addition, for shielding coils with other than the four-segment configuration, the analysis process will generally be the same.

  7. Deep-penetration calculations in concrete and iron for shielding of proton therapy accelerators

    International Nuclear Information System (INIS)

    Sheu, Rong-Jiun; Chen, Yen-Fu; Lin, Uei-Tyng; Jiang, Shiang-Huei

    2012-01-01

    Proton accelerators in the energy range of approximately 200 MeV have become increasingly popular for cancer treatment in recent years. These proton therapy facilities usually involve bulky concrete or iron in their shielding design or accelerator structure. Simple shielding data, such as source terms or attenuation lengths for various proton energies and materials are useful in designing accelerator shielding. Understanding the appropriateness or uncertainties associated with these data, which are largely generated from Monte Carlo simulations, is critical to the quality of a shielding design. This study demonstrated and investigated the problems of deep-penetration calculations on the estimation of shielding parameters through an extensive comparison between the FLUKA and MCNPX calculations for shielding against a 200-MeV proton beam hitting an iron target. Simulations of double-differential neutron production from proton bombardment were validated by comparison with experimental data. For the concrete shielding, the FLUKA calculated depth–dose distributions were consistent with the MCNPX results, except for some discrepancies in backward directions. However, for the iron shielding, if FLUKA is used inappropriately then overestimation of neutron attenuation can be expected as shown by this work because of the multigroup treatment for low-energy neutrons in FLUKA. Two neutron energy group structures, three degrees of self-shielding correction, and two iron compositions were considered in this study. Significant variation of the resulting attenuation lengths indicated the importance of problem-dependent multigroup cross sections and proper modeling of iron composition in deep-penetration calculations.

  8. A BRIEF ANALYSIS OF THE SHADOW ECONOMY IN EUROPE

    Directory of Open Access Journals (Sweden)

    Loredana Maftei

    2013-12-01

    Full Text Available Shadow economy affects all country around the world. European countries are affected by undeclared work, under-reporting and tax evasion. This phenomenon increases from West to East, the most affected being the Balkan area. The size of shadow economy is growing due to government actions, such as regulation and tax implementation. From a macroeconomic perspective, the economic cycle sustain the shadow economy levels. To combat this phenomenon it is necessary to adopt electronic payments, to reduce tax implementations and social contributions, to bring encouragement in cash deposits use and broaden credit cards.

  9. The asymptotic average-shadowing property and transitivity for flows

    International Nuclear Information System (INIS)

    Gu Rongbao

    2009-01-01

    The asymptotic average-shadowing property is introduced for flows and the relationships between this property and transitivity for flows are investigated. It is shown that a flow on a compact metric space is chain transitive if it has positively (or negatively) asymptotic average-shadowing property and a positively (resp. negatively) Lyapunov stable flow is positively (resp. negatively) topologically transitive provided it has positively (resp. negatively) asymptotic average-shadowing property. Furthermore, two conditions for which a flow is a minimal flow are obtained.

  10. Transmit antenna selection based on shadowing side information

    KAUST Repository

    Yilmaz, Ferkan

    2011-05-01

    In this paper, we propose a new transmit antenna selection scheme based on shadowing side information. In the proposed scheme, single transmit antenna which has the highest shadowing coefficient is selected. By the proposed technique, usage of the feedback channel and channel estimation complexity at the receiver can be reduced. We consider independent but not identically distributed Generalized-K composite fading model, which is a general composite fading & shadowing channel model for wireless environments. Exact closed-form outage probability, moment generating function and symbol error probability expressions are derived. In addition, theoretical performance results are validated by Monte Carlo simulations. © 2011 IEEE.

  11. Radiation shielding techniques and applications. 3. Analysis of Photon Streaming Through and Around Shield Doors

    International Nuclear Information System (INIS)

    Barnett, Marvin; Hack, Joe; Nathan, Steve; White, Travis

    2001-01-01

    Westinghouse Safety Management Solutions (Westinghouse SMS) has been tasked with providing radiological engineering design support for the new Commercial Light Water Reactor Tritium Extraction Facility (CLWR-TEF) being constructed at the Savannah River Site (SRS). The Remote Handling Building (RHB) of the CLWR-TEF will act as the receiving facility for irradiated targets used in the production of tritium for the U.S. Department of Energy (DOE). Because of the high dose rates, approaching 50 000 rads/h (500 Gy/h) from the irradiated target bundles, significant attention has been made to shielding structures within the facility. One aspect of the design that has undergone intense review is the shield doors. The RHB has six shield doors that needed to be studied with respect to photon streaming. Several aspects had to be examined to ensure that the design meets the radiation dose levels. Both the thickness and streaming issues around the door edges were designed and examined. Photon streaming through and around a shield door is a complicated problem, creating a reliance on computer modeling to perform the analyses. The computer code typically used by the Westinghouse SMS in the evaluation of photon transport through complex geometries is the MCNP Monte Carlo computer code. The complexity of the geometry within the problem can cause problems even with the Monte Carlo codes. Striking a balance between how the code handles transport through the shield door with transport through the streaming paths, particularly with the use of typical variance reduction methods, is difficult when trying to ensure that all important regions of the model are sampled appropriately. The thickness determination used a simple variance reduction technique. In construction, the shield door will not be flush against the wall, so a solid rectangular slab leaves streaming paths around the edges. Administrative controls could be used to control dose to workers; however, 10 CFR 835.1001 states

  12. A simple statistical signal loss model for deep underground garage

    DEFF Research Database (Denmark)

    Nguyen, Huan Cong; Gimenez, Lucas Chavarria; Kovacs, Istvan

    2016-01-01

    In this paper we address the channel modeling aspects for a deep-indoor scenario with extreme coverage conditions in terms of signal losses, namely underground garage areas. We provide an in-depth analysis in terms of path loss (gain) and large scale signal shadowing, and a propose simple...

  13. Shadow Segmentation and Augmentation Using á-overlay Models that Account for Penumbra

    DEFF Research Database (Denmark)

    Nielsen, Michael; Madsen, Claus B.

    2006-01-01

    This paper introduces a new concept within shadow segmentation. Previously, an image is considered to consist of shadow and non-shadow regions. Thus, a binary mask is estimated using various heuristics regarding structural and retinex/color constancy theories. We wish to model natural shadows so...

  14. Shielding analysis of the advanced voloxidation process

    Energy Technology Data Exchange (ETDEWEB)

    Park, Chang Je; Park, J. J.; Lee, J. W.; Shin, J. M.; Park, G. I.; Song, K. C

    2008-09-15

    This report deals describes how much a shielding benefit can be obtained by the Advanced Voloxidation process. The calculation was performed with the MCNPX code and a simple problem was modeled with a spent fuel source which was surrounded by a concrete wall. The source terms were estimated with the ORIGEN-ARP code and the gamma spectrum and the neutron spectrum were also obtained. The thickness of the concrete wall was estimated before and after the voloxidation process. From the results, the gamma spectrum after the voloxidation process was estimated as a 67% reduction compared with that of before the voloxidation process due to the removal of several gamma emission elements such as cesium and rubidium. The MCNPX calculations provided that the thickness of the general concrete wall could be reduced by 12% after the voloxidation process. And the heavy concrete wall provided a 28% reduction in the shielding of the source term after the voloxidation process. This can be explained in that there lots of gamma emission isotopes still exist after the advanced voloxidation process such as Pu-241, Y-90, and Sr-90 which are independent of the voloxidation process.

  15. The Dalkon Shield in perspective.

    Science.gov (United States)

    Pendergast, P; Hirsh, H L

    1986-01-01

    When the Dalkon Shield IUD became clinically available in the early 1970s, it appeared that an ideal contraceptive had been developed, with essentially no adverse effects (very safe) and a very high degree of efficacy. Within a few years, however, it became apparent that the Dalkon Shield had not lived up to expectations. In fact, it caused very severe complications, not infrequently resulting in the loss of reproductive ability and in 17 cases, death. In addition, the pregnancy rate among women using this IUD was significantly high, with many resulting in mid-trimester abortion when the IUD remained in-place. The authors trace the legal consequences of this medical disaster, which has resulted in both the development of new and the extension of old legal theories and doctrines involving negligence and product liability. Dalkon Shield litigation is most likely to continue. Many women are assumed to wear the shield still, and neither the FDA or A.H. Robins, manufacturer of the shield, has issued a formal recall.

  16. Radiation Shielding Materials and Containers Incorporating Same

    Energy Technology Data Exchange (ETDEWEB)

    Mirsky, Steven M.; Krill, Stephen J.; and Murray, Alexander P.

    2005-11-01

    An improved radiation shielding material and storage systems for radioactive materials incorporating the same. The PYRolytic Uranium Compound (''PYRUC'') shielding material is preferably formed by heat and/or pressure treatment of a precursor material comprising microspheres of a uranium compound, such as uranium dioxide or uranium carbide, and a suitable binder. The PYRUC shielding material provides improved radiation shielding, thermal characteristic, cost and ease of use in comparison with other shielding materials. The shielding material can be used to form containment systems, container vessels, shielding structures, and containment storage areas, all of which can be used to house radioactive waste. The preferred shielding system is in the form of a container for storage, transportation, and disposal of radioactive waste. In addition, improved methods for preparing uranium dioxide and uranium carbide microspheres for use in the radiation shielding materials are also provided.

  17. Shadow banking in China: expanding scale, evolving structure

    OpenAIRE

    Li, Cindy

    2013-01-01

    This Asia Focus provides an overview of shadow banking activities in China, their close ties with banks, reasons behind their rapid rise, the range of participants and products, and regulatory issues.

  18. Resource-Aware Navigation for Shadowed and Uncertain Environments

    Data.gov (United States)

    National Aeronautics and Space Administration — Discovery of off-Earth ice will transform space exploration. Volatiles that exist primarily in shadowed polar latitudes of planetary bodes could be harvested to...

  19. Testing General Relativity with the Shadow Size of Sgr A(*).

    Science.gov (United States)

    Johannsen, Tim; Broderick, Avery E; Plewa, Philipp M; Chatzopoulos, Sotiris; Doeleman, Sheperd S; Eisenhauer, Frank; Fish, Vincent L; Genzel, Reinhard; Gerhard, Ortwin; Johnson, Michael D

    2016-01-22

    In general relativity, the angular radius of the shadow of a black hole is primarily determined by its mass-to-distance ratio and depends only weakly on its spin and inclination. If general relativity is violated, however, the shadow size may also depend strongly on parametric deviations from the Kerr metric. Based on a reconstructed image of Sagittarius A^{*} (Sgr A^{*}) from a simulated one-day observing run of a seven-station Event Horizon Telescope (EHT) array, we employ a Markov chain Monte Carlo algorithm to demonstrate that such an observation can measure the angular radius of the shadow of Sgr A^{*} with an uncertainty of ∼1.5  μas (6%). We show that existing mass and distance measurements can be improved significantly when combined with upcoming EHT measurements of the shadow size and that tight constraints on potential deviations from the Kerr metric can be obtained.

  20. Physician shadowing by college students: what do patients think?

    OpenAIRE

    Bing-You, Robert G; Hayes, Victoria M; Skolfield, Jennifer L

    2014-01-01

    Background The objective of this study is to determine patients’ perceptions of physician shadowing by college students. Methods Thirty-two patients who agreed to have a college student shadow their physician participated in semi-structured interviews during July and August 2013 at two outpatient family medicine centers. Qualitative techniques were utilized to analyze the transcripts of the patient interviews and identify common themes. Results The majority of patients (78.1%) felt the colleg...

  1. Observation of the moon shadow in deep underground muon flux

    International Nuclear Information System (INIS)

    Allison, W. W. M.; Alner, G. J.; Ayres, D. S.; Cobb, J. H.; Fields, T. H.; Goodman, M. C.; Joffe-Minor, T.; Marshak, M. L.; Price, L. E.; Seidlein, R.; Thron, J. L.

    1999-01-01

    A shadow of the moon, with a statistical significance of 5σ, has been observed in the underground muon flux at a depth of 2090 mwe using the Soudan 2 detector. The angular resolution of the detector is well described by a Gaussian with σ le0.3degree. The position of the shadow confirms the alignment of the detector to better than 0.15degree. This alignment has remained stable during 10 years of data taking from 1989 through 1998

  2. Nuclear shadowing and the optics of hadronic fluctuations

    Energy Technology Data Exchange (ETDEWEB)

    Mankiewicz, L. E-mail: lech_mankiewicz@camk.edu.pl; Piller, G.; Vaenttinen, M.; Weise, W

    2001-06-04

    A coordinate-space description of shadowing in deep-inelastic lepton-nucleus scattering is presented. The picture in the laboratory frame is that of quark-gluon fluctuations of the high-energy virtual photon, propagating coherently over large light-cone distances in the nuclear medium. We discuss the detailed dependence of the coherence effects on the invariant mass of the fluctuation. We comment on the issue of possible saturation in the shadowing effects at very small Bjorken-x.

  3. On Risk Charges and Shadow Account Options in Pension Funds

    DEFF Research Database (Denmark)

    Jørgensen, Peter Løchte; Gatzert, Nadine

    2015-01-01

    to equityholders and our paper develops a model in which the influence of risk charges and shadow account options on stakeholders’ value can be quantified and studied. Our numerical results show that the value of shadow account options can be significant and thus come at the risk of expropriating policyholder...... wealth. However, our analysis also shows that this risk can be remedied if proper attention is given to the specific contract design and to the fixing of fair contract parameters at the outset....

  4. Light - Shadow Interactions in Italian Medieval Churches

    Science.gov (United States)

    Incerti, Manuela

    In the relationship between architecture and the sky, it is possible to identify three different design issues. The first regards the alignment of buildings with visible points on the horizon that coincide with the rising or setting of a celestial body (sun, planets, stars, or moon) on particular dates during the astronomical year (or liturgical year for sacred buildings). The second is the relationship between planimetric design and the design of the elevations. We are all familiar today with several "light effects", which sometimes have almost hierophanic characteristics that, on certain days of the year, were used to engross, captivate, and amaze the spectator. Contrary to the first two issues, the third comes after the design and building stages and concerns the question of decorative elements. It is reasonable to believe that many years after the works were terminated, certain wall finishings were chosen over others, such as painted frescoes or statues. Whoever did this was fully aware, thanks to direct observation, that such decoration would be struck by a single ray of light on a specific day. This chapter examines light-shadow interactions in some Italian medieval churches.

  5. Celestial shadows eclipses, transits, and occultations

    CERN Document Server

    Westfall, John

    2015-01-01

    Much of what is known about the universe comes from the study of celestial shadows—eclipses, transits, and occultations.  The most dramatic are total eclipses of the Sun, which constitute one of the most dramatic and awe-inspiring events of nature.  Though once a source of consternation or dread, solar eclipses now lead thousands of amateur astronomers and eclipse-chasers to travel to remote points on the globe to savor their beauty and the adrenaline-rush of experiencing totality, and were long the only source of information about the hauntingly beautiful chromosphere and corona of the Sun.   Long before Columbus, the curved shadow of the Earth on the Moon during a lunar eclipse revealed that we inhabit a round world. The rare and wonderful transits of Venus, which occur as it passes between the Earth and the Sun, inspired eighteenth century expeditions to measure the distance from the Earth to the Sun, while the recent transits of 2004 and 2012 were the most widely observed ever--and still produced re...

  6. Identification of Methodology of Indirect Assessment of Economy Shadowing

    Directory of Open Access Journals (Sweden)

    Avhustyn Ruslan R.

    2014-03-01

    Full Text Available The article explains the essence of the shadow economy as an objective phenomenon of socio-economic relations and its influence upon national economy security through instruments of pricing, fiscal restrictions, tax control, and banking and insurance regulation. It proves the necessity of use of the indirect method of assessment of the level of economy shadowing along with methods of direct control over the growth of shadowed economic relations, since such an approach would allow rational approach to identification of volumes and level of shadow activity. In the result of the study the article marks out varieties of indirect assessment of economy shadowing (methods of document, accounting and economic analysis, their specific features, advantages and shortcomings and results of practical use. The article reveals approaches and indicators of economic analysis that allow identification of reasons of deviations from the normal economic activity of economic subjects. It provides examples of the indirect method of assessment of the volume of shadowed economy that deal with analysis of demand on money and comparison of rates of the growth of the money supply with the volume of sight drafts with GDP.

  7. Shadows of Kerr Black Holes with Scalar Hair.

    Science.gov (United States)

    Cunha, Pedro V P; Herdeiro, Carlos A R; Radu, Eugen; Rúnarsson, Helgi F

    2015-11-20

    Using backwards ray tracing, we study the shadows of Kerr black holes with scalar hair (KBHSH). KBHSH interpolate continuously between Kerr BHs and boson stars (BSs), so we start by investigating the lensing of light due to BSs. Moving from the weak to the strong gravity region, BSs-which by themselves have no shadows-are classified, according to the lensing produced, as (i) noncompact, which yield not multiple images, (ii) compact, which produce an increasing number of Einstein rings and multiple images of the whole celestial sphere, and (iii) ultracompact, which possess light rings, yielding an infinite number of images with (we conjecture) a self-similar structure. The shadows of KBHSH, for Kerr-like horizons and noncompact BS-like hair, are analogous to, but distinguishable from, those of comparable Kerr BHs. But for non-Kerr-like horizons and ultracompact BS-like hair, the shadows of KBHSH are drastically different: novel shapes arise, sizes are considerably smaller, and multiple shadows of a single BH become possible. Thus, KBHSH provide quantitatively and qualitatively new templates for ongoing (and future) very large baseline interferometry observations of BH shadows, such as those of the Event Horizon Telescope.

  8. Simple prostatectomy

    Science.gov (United States)

    ... Han M, Partin AW. Simple prostatectomy: open and robot-assisted laparoscopic approaches. In: Wein AJ, Kavoussi LR, ... M. is also a founding member of Hi-Ethics and subscribes to the principles of the Health ...

  9. Simple unification

    International Nuclear Information System (INIS)

    Ponce, W.A.; Zepeda, A.

    1987-08-01

    We present the results obtained from our systematic search of a simple Lie group that unifies weak and electromagnetic interactions in a single truly unified theory. We work with fractionally charged quarks, and allow for particles and antiparticles to belong to the same irreducible representation. We found that models based on SU(6), SU(7), SU(8) and SU(10) are viable candidates for simple unification. (author). 23 refs

  10. Shielding structure analysis for LSDS facility

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Hong Yeop; Kim, Jeong Dong; Lee, Yong Deok; Kim, Ho Dong [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-05-15

    The nuclear material (Pyro, Spent nuclear fuel) itself and the target material to generate neutrons is the LSDS system for isotopic fissile assay release of high intensity neutron and gamma rays. This research was performed to shield from various strong radiation. A shielding evaluation was carried out with a facilities model of LSDS system. The MCNPX 2.5 code was used and a shielding evaluation was performed for the shielding structure and location. The radiation dose based on the hole structure and location of the wall was evaluated. The shielding evaluation was performed to satisfy the safety standard for a normal person (1 μSv/h) and to use enough interior space. The MCNPX2.5 code was used and a dose evaluation was performed for the location of the shielding material, shielding structure, and hole structure. The evaluation result differs according to the shielding material location. The dose rate was small when the shielding material was positioned at the center. The dose evaluation result regarding the location of the shielding material was applied to the facility and the shielding thickness was determined (In 50 cm + Borax 5 cm + Out 45cm). In the existing hole structure, the radiation leak is higher than the standard. A hole structure model to prevent leakage of radiation was proposed. The general public dose limit was satisfied when using the concrete reinforcement and a zigzag structure. The shielding result will be of help to the facility shielding optimization.

  11. Shielding structure analysis for LSDS facility

    International Nuclear Information System (INIS)

    Choi, Hong Yeop; Kim, Jeong Dong; Lee, Yong Deok; Kim, Ho Dong

    2014-01-01

    The nuclear material (Pyro, Spent nuclear fuel) itself and the target material to generate neutrons is the LSDS system for isotopic fissile assay release of high intensity neutron and gamma rays. This research was performed to shield from various strong radiation. A shielding evaluation was carried out with a facilities model of LSDS system. The MCNPX 2.5 code was used and a shielding evaluation was performed for the shielding structure and location. The radiation dose based on the hole structure and location of the wall was evaluated. The shielding evaluation was performed to satisfy the safety standard for a normal person (1 μSv/h) and to use enough interior space. The MCNPX2.5 code was used and a dose evaluation was performed for the location of the shielding material, shielding structure, and hole structure. The evaluation result differs according to the shielding material location. The dose rate was small when the shielding material was positioned at the center. The dose evaluation result regarding the location of the shielding material was applied to the facility and the shielding thickness was determined (In 50 cm + Borax 5 cm + Out 45cm). In the existing hole structure, the radiation leak is higher than the standard. A hole structure model to prevent leakage of radiation was proposed. The general public dose limit was satisfied when using the concrete reinforcement and a zigzag structure. The shielding result will be of help to the facility shielding optimization

  12. Shielding calculations for the design of neutron radiography facility around PARR

    International Nuclear Information System (INIS)

    Ashraf, M.M.; Khan, A.R.

    1989-06-01

    Shielding calculations for neutron radiography facility, proposed to be established around PARR have been carried out using two group diffusion theory and shielding formulae. Gamma radiation penetration calculations have been carried out using simple attenuation methods. The fabrication and installation of the neutron radiography facility would provide the basis for designing a better collimating system and would help establish under water radiography facility for the inspection of highly radioactive materials and components etc. (orig./A.B.)

  13. Measurement of the Shielding Effectiveness of Conducting Enclosures with the Image Theory

    Directory of Open Access Journals (Sweden)

    U. Paoletti

    2005-01-01

    Full Text Available Two simple techniques for the measurement of the shielding efficiency for the electric field of a symmetric enclosure are presented.y They allow measurements in the symmetry plane of the enclosure without disturbances b the cables. Measurements in near and far field regions are possible. Comparisons with simulation results are shown. Both techniques are particularly suitable for the evaluation of numerical techniques. Limits of the concept of shielding efficiency of enclosures at high frequencies are also briefly discussed.

  14. A Novel Radiation Shielding Material Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Radiation shielding simulations showed that epoxy loaded with 10-70% polyethylene would be an excellent shielding material against GCRs and SEPs. Milling produced an...

  15. Simulation of a Shielded Thermocouple

    African Journals Online (AJOL)

    performance of shielded thermocouple designs. A mathematical model of the thermocouple is obtained by derivation of the heat propagation equation in cylindrical coordinates and by considering the ... Here k is the thermal conductivity, p c is the specific heat capacity, ρ is the density,. ∞. T is the ambient temperature, and μ ...

  16. 3D Spatial and Spectral Fusion of Terrestrial Hyperspectral Imagery and Lidar for Hyperspectral Image Shadow Restoration Applied to a Geologic Outcrop

    Science.gov (United States)

    Hartzell, P. J.; Glennie, C. L.; Hauser, D. L.; Okyay, U.; Khan, S.; Finnegan, D. C.

    2016-12-01

    Recent advances in remote sensing technology have expanded the acquisition and fusion of active lidar and passive hyperspectral imagery (HSI) from an exclusively airborne technique to terrestrial modalities. This enables high resolution 3D spatial and spectral quantification of vertical geologic structures for applications such as virtual 3D rock outcrop models for hydrocarbon reservoir analog analysis and mineral quantification in open pit mining environments. In contrast to airborne observation geometry, the vertical surfaces observed by horizontal-viewing terrestrial HSI sensors are prone to extensive topography-induced solar shadowing, which leads to reduced pixel classification accuracy or outright removal of shadowed pixels from analysis tasks. Using a precisely calibrated and registered offset cylindrical linear array camera model, we demonstrate the use of 3D lidar data for sub-pixel HSI shadow detection and the restoration of the shadowed pixel spectra via empirical methods that utilize illuminated and shadowed pixels of similar material composition. We further introduce a new HSI shadow restoration technique that leverages collocated backscattered lidar intensity, which is resistant to solar conditions, obtained by projecting the 3D lidar points through the HSI camera model into HSI pixel space. Using ratios derived from the overlapping lidar laser and HSI wavelengths, restored shadow pixel spectra are approximated using a simple scale factor. Simulations of multiple lidar wavelengths, i.e., multi-spectral lidar, indicate the potential for robust HSI spectral restoration that is independent of the complexity and costs associated with rigorous radiometric transfer models, which have yet to be developed for horizontal-viewing terrestrial HSI sensors. The spectral restoration performance is quantified through HSI pixel classification consistency between full sun and partial sun exposures of a single geologic outcrop.

  17. Exhumation And Evolution Of Al-Taif Metamorphic Core Complex (Western Arabian Shield) During Dextral Transpressional Regime

    Science.gov (United States)

    El-Fakharani, Abdelhamid; El-Shafei, Mohamed; Hamimi, Zakaria

    2013-04-01

    Al-Taif metamorphic belt is a NE-trending belt decorating steeply dipping major transpressional shear zone in western central Arabian Shield. It comprises gneisses and migmatites that were syn-kinematically invaded under relatively high-grade metamorphic conditions by voluminous granitic bodies and a confluence of pegmatitic veins. Field mapping and outcrop investigation reveal that the belt was evolved during at least three Neoproterozoic deformations (D1-D3). D1 and D2 were progressive deformations, took place during a contractional regime, and resulted in SW-mildly plunging isoclinal folds, superimposed by NE- gently to moderately plunging folds. The prevailed tectonic regime during D3was primordially plastic, accompanied with a NE-oriented oblique shearing that was subsequently evolved as semi ductile-semi brittle shearing during an episode of exhumation. Mesoscopic kinematic indicators, as well as microstructural analysis of the collected rock samples, reflect dextral sense of shearing. Such style of shearing is most probably the conjugate trend of the NNW- to NW- oriented sinistral Najd Fault System. Various cross cutting structures and overprinting relations were detected at both the outcrop- and microscopic scales, including; ductile S2folia with ESE-plunging amphibole mineral lineations; narrow, steeply dipping ductile D2 shear zones; and semi brittle to brittle fault zones. S-C' fabrics, asymmetric strain shadows around porphyroclasts and drag fault indicate a top-to-the-NE sense of shear for most structures. The geometry and style of deformation, together with map pattern highlighted in this study attest a simple shear rotational strain origin for the domed mylonitic foliation (S1) and mineral elongation lineation (L1). This result is in congruent with the landform pattern recorded in the inner parts of the metamorphic core complexes.

  18. Simple Interactions

    DEFF Research Database (Denmark)

    and international public. The exhibition Simple Interactions. Sound Art from Japan presents works by 9 Japanese artists at the Museum of Contemporary Art Roskilde. The exhibition mixes installations, performances and documentations, all of which examine how simple interactions can create complex systems...... and patterns. Works and performances by the following artists are presented: Yuji DOGANE - Yukio FUJIMOTO - Atsuhiro ITO - Soichiro MIHARA - Atsushi NISHIJIMA - Jio SHIMIZU - Toshiya TSUNODA - Tetsuya UMEDA - Miki YUI The book presents texts by Minoru HATANAKa; Takashi KOJIMA, Rune SØCHTING and the editors...

  19. A source of illumination for low-noise ‘Violin-Mode’ shadow sensors, intended for use in interferometric gravitational wave detectors

    Science.gov (United States)

    Lockerbie, N. A.; Tokmakov, K. V.; Strain, K. A.

    2014-12-01

    A low-noise source of illumination is described for shadow sensors having a displacement sensitivity of (69  ±  13) picometres (rms)/√Hz, at 500 Hz, over a measuring span of ±0.1 mm. These sensors were designed to detect ‘Violin-Mode’ resonances in the suspension fibres of the test-masses/mirrors for the Advanced LIGO (Laser Interferometer Gravitational wave Observatory) gravitational wave detectors. The source of illumination (emitter) described here used a single column of 8 × miniature near infrared LEDs (λ = 890 nm). These emitters cast the shadows of 400 μm diameter fused silica suspension fibres onto their complementary shadow-displacement detectors, located at a distance of 74 fibre diameters (29.6 mm) behind the axes of the fibres themselves. Violin-Mode vibrations of each fibre were sensed as differential ac photocurrents in the corresponding ‘split-photodiode’ detector. This paper describes the design, construction, noise analysis, and measures that were taken in the conception of the emitters, in order to produce high-contrast shadows at such distant detectors. In this way it proved possible to obtain, simultaneously, a very high transfer sensitivity to Violin-Mode vibration of the fibres, and a very low level of detection noise—close to the fundamental shot noise limit—whilst remaining within the constraints of this simple design of emitter. The shadow detector is described in an accompanying paper.

  20. Device for sealing and shielding a nuclear fuel storage tank

    International Nuclear Information System (INIS)

    Masaki, Gengo.

    1975-01-01

    Object: To provide a shield device for opening and closing a great opening in a relay-storage-tank within a hot cell for temporarily storing a nuclear fuel, in which the device is simplified in construction and which can perform the opening and closing operation in simple, positive and quick manner. Structure: A biological shield is positioned upwardly of an opening of a nuclear fuel storage tank to render an actuator inoperative. A sealing plate, which is pivotally supported by a plurality of support rod devices from the biological shield for parallel movement with respect to the biological shield, comes in contact with a resilient seal disposed along the entire peripheral edge of the opening to form an air-tight seal therebetween. In order to release the opening, the actuator is first actuated and the end of the sealing plate is horizontally pressed by a piston rod thereof. Then, the sealing plate is moved along the line depicted by the end of the support rod in the support rod devices and as a consequence, the plate is moved away from the resilient seal in the peripheral edge of the opening. When a driving device is actuated to travel the plate along the aforesaid line while maintaining the condition as described, the biological device moves along the guide. (Kamimura, M.)

  1. Using Shadow Page Cache to Improve Isolated Drivers Performance

    Directory of Open Access Journals (Sweden)

    Hao Zheng

    2015-01-01

    Full Text Available With the advantage of the reusability property of the virtualization technology, users can reuse various types and versions of existing operating systems and drivers in a virtual machine, so as to customize their application environment. In order to prevent users’ virtualization environments being impacted by driver faults in virtual machine, Chariot examines the correctness of driver’s write operations by the method of combining a driver’s write operation capture and a driver’s private access control table. However, this method needs to keep the write permission of shadow page table as read-only, so as to capture isolated driver’s write operations through page faults, which adversely affect the performance of the driver. Based on delaying setting frequently used shadow pages’ write permissions to read-only, this paper proposes an algorithm using shadow page cache to improve the performance of isolated drivers and carefully study the relationship between the performance of drivers and the size of shadow page cache. Experimental results show that, through the shadow page cache, the performance of isolated drivers can be greatly improved without impacting Chariot’s reliability too much.

  2. Using shadow page cache to improve isolated drivers performance.

    Science.gov (United States)

    Zheng, Hao; Dong, Xiaoshe; Wang, Endong; Chen, Baoke; Zhu, Zhengdong; Liu, Chengzhe

    2015-01-01

    With the advantage of the reusability property of the virtualization technology, users can reuse various types and versions of existing operating systems and drivers in a virtual machine, so as to customize their application environment. In order to prevent users' virtualization environments being impacted by driver faults in virtual machine, Chariot examines the correctness of driver's write operations by the method of combining a driver's write operation capture and a driver's private access control table. However, this method needs to keep the write permission of shadow page table as read-only, so as to capture isolated driver's write operations through page faults, which adversely affect the performance of the driver. Based on delaying setting frequently used shadow pages' write permissions to read-only, this paper proposes an algorithm using shadow page cache to improve the performance of isolated drivers and carefully study the relationship between the performance of drivers and the size of shadow page cache. Experimental results show that, through the shadow page cache, the performance of isolated drivers can be greatly improved without impacting Chariot's reliability too much.

  3. eShadow: A tool for comparing closely related sequences

    Energy Technology Data Exchange (ETDEWEB)

    Ovcharenko, Ivan; Boffelli, Dario; Loots, Gabriela G.

    2004-01-15

    Primate sequence comparisons are difficult to interpret due to the high degree of sequence similarity shared between such closely related species. Recently, a novel method, phylogenetic shadowing, has been pioneered for predicting functional elements in the human genome through the analysis of multiple primate sequence alignments. We have expanded this theoretical approach to create a computational tool, eShadow, for the identification of elements under selective pressure in multiple sequence alignments of closely related genomes, such as in comparisons of human to primate or mouse to rat DNA. This tool integrates two different statistical methods and allows for the dynamic visualization of the resulting conservation profile. eShadow also includes a versatile optimization module capable of training the underlying Hidden Markov Model to differentially predict functional sequences. This module grants the tool high flexibility in the analysis of multiple sequence alignments and in comparing sequences with different divergence rates. Here, we describe the eShadow comparative tool and its potential uses for analyzing both multiple nucleotide and protein alignments to predict putative functional elements. The eShadow tool is publicly available at http://eshadow.dcode.org/

  4. A separable shadow Hamiltonian hybrid Monte Carlo method

    Science.gov (United States)

    Sweet, Christopher R.; Hampton, Scott S.; Skeel, Robert D.; Izaguirre, Jesús A.

    2009-11-01

    Hybrid Monte Carlo (HMC) is a rigorous sampling method that uses molecular dynamics (MD) as a global Monte Carlo move. The acceptance rate of HMC decays exponentially with system size. The shadow hybrid Monte Carlo (SHMC) was previously introduced to reduce this performance degradation by sampling instead from the shadow Hamiltonian defined for MD when using a symplectic integrator. SHMC's performance is limited by the need to generate momenta for the MD step from a nonseparable shadow Hamiltonian. We introduce the separable shadow Hamiltonian hybrid Monte Carlo (S2HMC) method based on a formulation of the leapfrog/Verlet integrator that corresponds to a separable shadow Hamiltonian, which allows efficient generation of momenta. S2HMC gives the acceptance rate of a fourth order integrator at the cost of a second-order integrator. Through numerical experiments we show that S2HMC consistently gives a speedup greater than two over HMC for systems with more than 4000 atoms for the same variance. By comparison, SHMC gave a maximum speedup of only 1.6 over HMC. S2HMC has the additional advantage of not requiring any user parameters beyond those of HMC. S2HMC is available in the program PROTOMOL 2.1. A Python version, adequate for didactic purposes, is also in MDL (http://mdlab.sourceforge.net/s2hmc).

  5. The interrupted power law and the size of shadow banking.

    Science.gov (United States)

    Fiaschi, Davide; Kondor, Imre; Marsili, Matteo; Volpati, Valerio

    2014-01-01

    Using public data (Forbes Global 2000) we show that the asset sizes for the largest global firms follow a Pareto distribution in an intermediate range, that is "interrupted" by a sharp cut-off in its upper tail, where it is totally dominated by financial firms. This flattening of the distribution contrasts with a large body of empirical literature which finds a Pareto distribution for firm sizes both across countries and over time. Pareto distributions are generally traced back to a mechanism of proportional random growth, based on a regime of constant returns to scale. This makes our findings of an "interrupted" Pareto distribution all the more puzzling, because we provide evidence that financial firms in our sample should operate in such a regime. We claim that the missing mass from the upper tail of the asset size distribution is a consequence of shadow banking activity and that it provides an (upper) estimate of the size of the shadow banking system. This estimate-which we propose as a shadow banking index-compares well with estimates of the Financial Stability Board until 2009, but it shows a sharper rise in shadow banking activity after 2010. Finally, we propose a proportional random growth model that reproduces the observed distribution, thereby providing a quantitative estimate of the intensity of shadow banking activity.

  6. Abnormal chest shadow on CT in immunosuppressed patients

    International Nuclear Information System (INIS)

    Tanaka, Nobuyuki; Matsumoto, Tsuneo; Nakamura, Hiroshi

    1992-01-01

    An abnormal chest shadow was observed on CT scans in 25 cases of 23 immunosuppressed patients. Pulmonary disease was pathologically confirmed to be pneumocystis carinii pneumonia (PC pneumonia) in four patients, cytomegalovirus pneumonia (CMV pneumonia) in one, bacterial pneumonia in seven, fungal infection in three, miliary tuberculosis in one, leukemic infiltration in two, lymphangitis carcinomatosa in three, drug-induced pneumonitis in three, and ARDS in one. In almost all patients, especially those with infectious diseases such as PC pneumonia, CMV pneumonia, and bacterial pneumonia, the abnormal shadow was wide and visible in the bilateral lung fields. We presumed that such findings as lobular shadow, centrilobular shadow, and mosaic pattern reflected the extension of disease via the respiratory tract, and that those findings are typical of infectious diseases. Because such findings as abnormal linear shadow and swelling of a broncho-vascular bundle were very frequently recognized in patients with lymphangitis carcinomatosa and frequently recognized in those with drug-induced pneumonitis, these diseases may be distinguished from other diseases. An area of slightly increased density was frequently recognized in patients with PC pneumonia, bacterial pneumonia, and drug-induced pneumonitis. Such lesions were pathologically confirmed to be located in the interstitium and/or alveolus. CT was extremely useful in comprehending the character and extension of particular diseases among various diseases. As the number of patients studied was small, the utility of CT in immunosuppressed patients requires further investigation in a larger number of patients. (author)

  7. Survivor shielding. Part A. Nagasaki factory worker shielding

    International Nuclear Information System (INIS)

    Santoro, Robert T.; Barnes, John M.; Azmy, Yousry Y.; Kerr, George D.; Egbert, Stephen D.; Cullings, Harry M.

    2005-01-01

    Recent investigations based on conventional chromosome aberration data by the RERF suggest that the DS86 doses received by many Nagasaki factory workers may have been overestimated by as much as 40% relative to those for other survivors in Japanese-type houses and other shielding configurations (Kodama et al. 2001). Since the factory workers represent about 25% of the Nagasaki survivors with DS86 doses in excess of 0.5 Gy (50 rad), systematic errors in their dose estimates can have a major impact on the risk coefficients from RERF studies. The factory worker doses may have been overestimated for a number of reasons. The calculation techniques, including the factory building modeling, weapon source spectra and cross-section data used in the DS86 shielding calculations were not detailed enough to replicate actual conditions. The models used did not take into account local shielding provided by machinery, tools, and the internal structure in the buildings. In addition, changes in the disposition of shielding following collapse of the building by the blast wave were not considered. The location of large factory complexes may be uncertain, causing large numbers of factory survivors, correctly located relative to each other, to be uniformly too close to the hypocenter. Any or all of these reasons are sufficient to result in an overestimate of the factory worker doses. During the DS02 studies, factory worker doses have been reassessed by more carefully modeling the factory buildings, incorporating improved radiation transport methods and cross-section data and using the most recent bomb leakage spectra (Chapter 2). Two-dimensional discrete ordinates calculations were carried out initially to estimate the effects of workbenches and tools on worker doses to determine if the inclusion of these components would, in fact, reduce the dose by amounts consistent with the RERF observations (Kodama et al. 2001). (author)

  8. Neutronic design of MYRRHA reactor hall shielding

    Directory of Open Access Journals (Sweden)

    Celik Yurdunaz

    2017-01-01

    Full Text Available The lateral shielding of a 600 MeV proton linear accelerator beam line in the MYRRHA reactor hall has been assessed using neutronic calculations by the MCNPX code complemented with analytical predictions. Continuous beam losses were considered to define the required shielding thickness that meets the requirements for the dose rate limits. Required shielding thicknesses were investigated from the viewpoint of accidental full beam loss as well as beam loss on collimator. The results confirm that the required shielding thicknesses are highly sensitive to the spatial shape of the beam and strongly divergent beam losses. Therefore shielding barrier should be designed according to the more conservative assumptions.

  9. The Dark Shadow of Virtual Reality

    Directory of Open Access Journals (Sweden)

    Claire Su-Yeon Park

    2018-01-01

    Full Text Available Virtual Reality (VR technology are entering nursing education at a rapid speed (Foronda et al., 2017. VR has been reported in the nursing literature to significantly improve students’ performance (Jenson & Forsyth, 2012; Park, 2016; Foronda et al., 2017 even though the body of evidence in terms of the number and research quality of peer reviewed research papers is not yet substantial enough to identify VR technology’s effectiveness. However, VR is not actually reality. VR may not actually reflect reality. Young people (and even adults may not perceive the different between reality and VR. They may not yet be mature enough to distinguish the difference. However, VR technology are going much further than traditional educational methods by allowing humans to experience a much higher level of immersion through a virtual image. Even the gap between advances in VR technology and its application to education science is widening, causing serious concern. The advance in VR technology is value-neutral. As with all things, whether something is good or bad depends on how humans use it. VR can be useful, for example, when it enables scholars to attend an international conference without traveling to the physical convention center. VR provides the ability to speak, listen, and discuss in real time. Those using VR can choose to view a featured or real-time image of the other participants as if they were actually at the conference. Further, remote participants can feel touch through electronic sensors attached to their body. How amazing! The problem with VR lies in the fact that we are not ready to cope with any possible harmful influences caused by advances in VR technology. But what is the “Dark Shadow of VR,” and why does it cause concern, particularly in pedagogy? Luc Besson’s 2017 film Valerian and the City of a Thousand Plants showed an exceptional VR world, “Big Market,” a shopping-focused VR platform. But such a world is no longer strictly

  10. Multiple shooting shadowing for sensitivity analysis of chaotic dynamical systems

    Science.gov (United States)

    Blonigan, Patrick J.; Wang, Qiqi

    2018-02-01

    Sensitivity analysis methods are important tools for research and design with simulations. Many important simulations exhibit chaotic dynamics, including scale-resolving turbulent fluid flow simulations. Unfortunately, conventional sensitivity analysis methods are unable to compute useful gradient information for long-time-averaged quantities in chaotic dynamical systems. Sensitivity analysis with least squares shadowing (LSS) can compute useful gradient information for a number of chaotic systems, including simulations of chaotic vortex shedding and homogeneous isotropic turbulence. However, this gradient information comes at a very high computational cost. This paper presents multiple shooting shadowing (MSS), a more computationally efficient shadowing approach than the original LSS approach. Through an analysis of the convergence rate of MSS, it is shown that MSS can have lower memory usage and run time than LSS.

  11. Ferromagnetic shadow mask for spray coating of polymer patterns

    DEFF Research Database (Denmark)

    Keller, Stephan Sylvest; Bosco, Filippo; Boisen, Anja

    2013-01-01

    We present the fabrication of a wafer-scale shadow mask with arrays of circular holes with diameters of 150–400 μm. Standard UV photolithography is used to define 700 μm thick SU-8 structures followed by electroplating of nickel and etching of the template. The ferromagnetic properties of the sha......We present the fabrication of a wafer-scale shadow mask with arrays of circular holes with diameters of 150–400 μm. Standard UV photolithography is used to define 700 μm thick SU-8 structures followed by electroplating of nickel and etching of the template. The ferromagnetic properties...... of the shadow mask allow magnetic clamping to the substrate and spray coating of well defined polymer patterns....

  12. Shadow corrosion evaluation in the Studsvik R2 reactor

    International Nuclear Information System (INIS)

    Sanders, Ch.; Lysell, G.

    2000-01-01

    Post-irradiation examination has shown that increased corrosion occurs when zirconium alloys are in contact with or in proximity to other metallic objects. The observations indicate an influence of irradiation from the adjacent component as the enhanced corrosion occurs as a 'shadow' of the metallic object on the zirconium surface. This phenomenon could ultimately limit the lifetime of certain zirconium alloy components in the reactor. The Studsvik R2 materials test reactor has an In-Core Autoclave (INCA) test facility especially designed for water chemistry and materials research. The INCA facility has been evaluated and found suitable for shadow corrosion studies. The R2 reactor core containing the INCA facility was modeled with the Monte Carlo N-Particle (MCNP) code in order to evaluate the electron deposition in various materials and to develop a hypothesis of the shadow corrosion mechanism. (authors)

  13. Facility target insert shielding assessment

    Energy Technology Data Exchange (ETDEWEB)

    Mocko, Michal [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-10-06

    Main objective of this report is to assess the basic shielding requirements for the vertical target insert and retrieval port. We used the baseline design for the vertical target insert in our calculations. The insert sits in the 12”-diameter cylindrical shaft extending from the service alley in the top floor of the facility all the way down to the target location. The target retrieval mechanism is a long rod with the target assembly attached and running the entire length of the vertical shaft. The insert also houses the helium cooling supply and return lines each with 2” diameter. In the present study we focused on calculating the neutron and photon dose rate fields on top of the target insert/retrieval mechanism in the service alley. Additionally, we studied a few prototypical configurations of the shielding layers in the vertical insert as well as on the top.

  14. A practical neutron shielding design based on data-base interpolation

    International Nuclear Information System (INIS)

    Jiang, S.H.; Sheu, R.J.

    1993-01-01

    Neutron shielding design is an important part of the construction of nuclear reactors and high-energy accelerators. Neutron shielding design is also indispensable in the packaging and storage of isotopic neutron sources. Most efforts in the development of neutron shielding design have been concentrated on nuclear reactor shielding because of its huge mass and strict requirement of accuracy. Sophisticated computational tools, such as transport and Monte Carlo codes and detailed data libraries have been developed. In principle, now, neutron shielding, in spite of its complexity, can be designed in any detail and with fine accuracy. However, in most practical cases, neutron shielding design is accomplished with simplified methods. Unlike practical gamma-ray shielding design, where exponential attenuation coupled with buildup factors has been applied effectively and accurately, simplified neutron shielding design, either by using removal cross sections or by applying charts or tables of transmission factors such as the National Council on Radiation Protection and Measurements (NCRP) 38 (Ref. 1) for general neutron protection or to NCRP 51 (Ref. 2) for accelerator neutron shielding, is still very primitive and not well established. The available data are limited in energy range, materials, and thicknesses, and the estimated results are only roughly accurate. It is the purpose of this work to establish a simple, convenient, and user-friendly general-purpose computational tool for practical preliminary neutron shielding design that is reasonably accurate. A wide-range (energy, material, and thickness) data base of dose transmission factors has been generated by applying one-dimensional transport calculations in slab geometry

  15. Radiation shield vest and skirt

    International Nuclear Information System (INIS)

    Maine, G.J.

    1982-01-01

    A two-piece garment is described which provides shielding for female workers exposed to radiation. The upper part is a vest, overlapping and secured in the front by adjustable closures. The bottom part is a wraparound skirt, also secured by adjustable closures. The two parts overlap, thus providing continuous protection from shoulder to knee and ensuring that the back part of the body is protected as well as the front

  16. Handbook of radiation shielding data

    International Nuclear Information System (INIS)

    Courtney, J.C.

    1976-07-01

    This handbook is a compilation of data on units, conversion factors, geometric considerations, sources of radiation, and the attenuation of photons, neutrons, and charged particles. It also includes related topics in health physics. Data are presented in tabular and graphical form with sufficient narrative for a least first-approximation solutions to a variety of problems in nuclear radiation protection. Members of the radiation shielding community contributed the information in this document from unclassified and uncopyrighted sources, as referenced

  17. Shielding Idiosyncrasy from Isomorphic Pressures

    DEFF Research Database (Denmark)

    Alvarez, José Luis; Mazza, Carmelo; Strandgaard Pedersen, Jesper

    2003-01-01

    with legitimacyin the field. Our theory of creative actionfor optimal distinctiveness suggests thatfilm directors increase their control bypersonally consolidating artistic andproduction roles, by forming closepartnership with committed producer, andby establishing own production company.Ironically, to escape......Abstract. This paper advances a microtheory of creative action by examining howdistinctive artists shield their idiosyncraticstyles from the isomorphic pressures of afield. It draws on the cases of threeinternationally recognized, distinctiveEuropean film directors - Pedro Almodóvar(Spain), Nanni...

  18. Uranium self-shielding in fast reactor blankets

    Energy Technology Data Exchange (ETDEWEB)

    Kadiroglu, O.K.; Driscoll, M.J.

    1976-03-01

    The effects of heterogeneity on resonance self-shielding are examined with particular emphasis on the blanket region of the fast breeder reactor and on its dominant reaction--capture in /sup 238/U. The results, however, apply equally well to scattering resonances, to other isotopes (fertile, fissile and structural species) and to other environments, so long as the underlying assumptions of narrow resonance theory apply. The heterogeneous resonance integral is first cast into a modified homogeneous form involving the ratio of coolant-to-fuel fluxes. A generalized correlation (useful in its own right in many other applications) is developed for this ratio, using both integral transport and collision probability theory to infer the form of correlation, and then relying upon Monte Carlo calculations to establish absolute values of the correlation coefficients. It is shown that a simple linear prescription can be developed for the flux ratio as a function of only fuel optical thickness and the fraction of the slowing-down source generated by the coolant. This in turn permitted derivation of a new equivalence theorem relating the heterogeneous self-shielding factor to the homogeneous self-shielding factor at a modified value of the background scattering cross section per absorber nucleus. A simple version of this relation is developed and used to show that heterogeneity has a negligible effect on the calculated blanket breeding ratio in fast reactors.

  19. Photonic Bandgap (PBG) Shielding Technology

    Science.gov (United States)

    Bastin, Gary L.

    2007-01-01

    Photonic Bandgap (PBG) shielding technology is a new approach to designing electromagnetic shielding materials for mitigating Electromagnetic Interference (EM!) with small, light-weight shielding materials. It focuses on ground planes of printed wiring boards (PWBs), rather than on components. Modem PSG materials also are emerging based on planar materials, in place of earlier, bulkier, 3-dimensional PBG structures. Planar PBG designs especially show great promise in mitigating and suppressing EMI and crosstalk for aerospace designs, such as needed for NASA's Constellation Program, for returning humans to the moon and for use by our first human visitors traveling to and from Mars. Photonic Bandgap (PBG) materials are also known as artificial dielectrics, meta-materials, and photonic crystals. General PBG materials are fundamentally periodic slow-wave structures in I, 2, or 3 dimensions. By adjusting the choice of structure periodicities in terms of size and recurring structure spacings, multiple scatterings of surface waves can be created that act as a forbidden energy gap (i.e., a range of frequencies) over which nominally-conductive metallic conductors cease to be a conductor and become dielectrics. Equivalently, PBG materials can be regarded as giving rise to forbidden energy gaps in metals without chemical doping, analogous to electron bandgap properties that previously gave rise to the modem semiconductor industry 60 years ago. Electromagnetic waves cannot propagate over bandgap regions that are created with PBG materials, that is, over frequencies for which a bandgap is artificially created through introducing periodic defects

  20. Shielding wall for thermonuclear device

    International Nuclear Information System (INIS)

    Uchida, Takaho.

    1989-01-01

    This invention concerns shielding walls opposing to plasmas of a thermonuclear device and it is an object thereof to conduct reactor operation with no troubles even if a portion of shielding wall tiles should be damaged. That is, the shielding wall tiles are constituted as a dual layer structure in which the lower base tiles are connected by means of bolts to first walls. Further, the upper surface tiles are bolt-connected to the layer base tiles. In this structure, the plasma thermal loads are directly received by the surface layer tiles and heat is conducted by means of conduction and radiation to the underlying base tiles and the first walls. Even upon occurrence of destruction accidents to the surface layer tiles caused by incident heat or electromagnetic force upon elimination of plasmas, since the underlying base tiles remain as they are, the first walls constituted with stainless steels, etc. are not directly exposed to the plasmas. Accordingly, the integrity of the first walls having cooling channels can be maintained and sputtering intrusion of atoms of high atom number into the plasmas can be prevented. (I.S.)

  1. ATLAS Award for Shield Supplier

    CERN Multimedia

    2004-01-01

    ATLAS technical coordinator Dr. Marzio Nessi presents the ATLAS supplier award to Vojtech Novotny, Director General of Skoda Hute.On 3 November, the ATLAS experiment honoured one of its suppliers, Skoda Hute s.r.o., of Plzen, Czech Republic, for their work on the detector's forward shielding elements. These huge and very massive cylinders surround the beampipe at either end of the detector to block stray particles from interfering with the ATLAS's muon chambers. For the shields, Skoda Hute produced 10 cast iron pieces with a total weight of 780 tonnes at a cost of 1.4 million CHF. Although there are many iron foundries in the CERN member states, there are only a limited number that can produce castings of the necessary size: the large pieces range in weight from 59 to 89 tonnes and are up to 1.5 metres thick.The forward shielding was designed by the ATLAS Technical Coordination in close collaboration with the ATLAS groups from the Czech Technical University and Charles University in Prague. The Czech groups a...

  2. Desert Shield - Leader’s Safety Guide

    Science.gov (United States)

    1990-08-01

    surfaces such as glass , mirrors, and windows . • Ensure laser safety filters are installed on binoculars and other optical devices when observing...wadis Q Strong winds (30 mph in p.m.; 75 mph in windstorms ) Q Large fluctuations in day/night temperatures (up to 70°F.) • Sandy deserts a Poor...Monitor shadows cast by near objects such as landing gear or skid shadows during hover. • Keep windscreen and door windows clean of sand and dust

  3. Desert Shield Leader’s Safety Guide

    Science.gov (United States)

    1990-12-01

    lasers. • Caution personnel to fire lasers only at designated targets and to never fire at specular surfaces such as glass , mirrors, and windows ... windstorms ) Q Large fluctuations in day/night temperatures (up to 70°F.) • Sandy deserts Q Poor wheeled vehicle off-road mobility/stability...34 desert during the day. • Monitor shadows cast by near objects such as landing gear or skid shadows during hover. • Keep windscreen and door windows

  4. Medium Access Control for Opportunistic Concurrent Transmissions under Shadowing Channels

    Directory of Open Access Journals (Sweden)

    Seung Min Hur

    2009-06-01

    Full Text Available We study the problem of how to alleviate the exposed terminal effect in multihop wireless networks in the presence of log-normal shadowing channels. Assuming node location information, we propose an extension of the IEEE 802.11 MAC protocol that schedules concurrent transmissions in the presence of log-normal shadowing, thus mitigating the exposed terminal problem and improving network throughput and delay performance. We observe considerable improvements in throughput and delay achieved over the IEEE 802.11 MAC under various network topologies and channel conditions in ns-2 simulations, which justify the importance of considering channel randomness in MAC protocol design for multihop wireless networks.

  5. The Modified Socket Shield Technique.

    Science.gov (United States)

    Han, Chang-Hun; Park, Kwang-Bum; Mangano, Francesco Guido

    2018-03-20

    In the anterior regions, the resorption of the buccal bone after tooth extraction leads to a contraction of the overlying soft tissues, resulting in an esthetic problem, particularly with immediate implant placement. In the socket shield technique, the buccal root section of the tooth is maintained, to preserve the buccal bone for immediate implant placement. The aim of this prospective study was to investigate the survival, stability, and complication rates of implants placed using a "modified" socket shield technique. Over a 2-year period, all patients referred to a dental clinic for treatment with oral implants were considered for inclusion in this study. Inclusion criteria were healthy adult patients who presented nonrestorable single teeth with intact buccal periodontal tissues in the anterior regions of both jaws. Exclusion criteria were teeth with present/past periodontal disease, vertical root fractures on the buccal aspect, horizontal fractures below bone level, and external/internal resorptions. The buccal portion of the root was retained to prevent the resorption of the buccal bone; the shield was 1.5 mm thick with the most coronal portion at the bone crest level. All patients then underwent immediate implants. In the patient with a gap between the implant and shield, no graft material was placed. All implants were immediately restored with single crowns and followed for 1 year. The main outcomes were implant survival, stability, and complications. Thirty patients (15 males, 15 females; mean age was 48.2 ± 15.0 years) were enrolled in the study and installed with 40 immediate implants. After 1 year, all implants were functioning, for a survival rate of 100%; excellent implant stability was reported (mean implant stability quotient at placement: 72.9 ± 5.9; after 1 year: 74.6 ± 2.7). No biologic complications were reported, and the incidence of prosthetic complications was low (2.5%). The "modified" socket shield technique seems to be a

  6. SATIF-2 shielding aspects of accelerators, targets and irradiation facilities

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-31

    Particle accelerators have evolved over the last 50 years from simple devices to powerful machines, and will continue to have an important impact on research, technology and lifestyle. Today they cover a wide range of applications, from television and computer displays in households to the investigation of the origin and structure of matter. It has become common practice to use them for material science and medical applications. In recent years, requirements from new technological and research applications have emerged, such as increased particle beams intensities, higher flexibility, etc., giving rise to new radiation shielding aspects and problems. These proceedings review recent progress in radiation shielding of accelerator facilities, and evaluate advancements with respect to international co-operation in this field.

  7. Gamma ray absorption of cylindrical fissile material with dual shields

    International Nuclear Information System (INIS)

    Wu Chenyan; Cheng Yiying; Huang Yongyi; Lu Fuquan; Yang Fujia

    2005-01-01

    This work analyzed the gamma ray attenuation effect from the self-absorption and shield attenuation perspectively. An exact mathematical equation was given for the geometric factor of the cylindrical fissile material with dual shields. In addition, several approximation approaches suitable for real situation were discussed, especially in the radial and axial directions of the cylinders, since the G-factors have simple forms. Then the space distribution patterns of the G-factor were analyzed based on numerical result and effective ways to solved the geometric information of the cylindrical fissile material, the radii and the heights, were deduced. This method was checked and verified by numerical calculation. Because of the efficiency of the method, it is ideal for application in real situations, such as nuclear safeguards, which demands speed of detection and accuracy of geometric analysis. (authors)

  8. Shielding aspects of accelerators, targets and irradiation facilities - SATIF 5

    International Nuclear Information System (INIS)

    2001-01-01

    Over the last 50 years particle accelerators have evolved from simple devices to powerful machines, and will continue to have an important impact on research, technology and lifestyle. Today, they cover a wide range of applications, from television and computer displays in households to investigating the origin and structure of matter. It has become common practice to use particle accelerators for material science and medical applications. In recent years, requirements from new technological and research applications have emerged, giving rise to new radiation shielding aspects and problems. These workshop proceedings review recent progress in radiation shielding of accelerator facilities, evaluating advancements and discussing further developments needed with respect to international co-operation in this field. (author)

  9. Terrestrial Background Reduction in RPM Systems by Direct Internal Shielding

    International Nuclear Information System (INIS)

    Robinson, Sean M.; Ashbaker, Eric D.; Schweppe, John E.

    2008-01-01

    Gamma-ray detection systems that are close to the earth or other sources of background radiation often require shielding, especially when trying to detect a relatively weak source. One particular case of interest that we address in this paper is that encountered by the Radiation Portal Monitors (RPMs) systems placed at border-crossing Ports of Entry (POE). These RPM systems are used to screen for illicit radiological materials, and they are often placed in situations where terrestrial background is large. In such environments, it is desirable to consider simple physical modifications that could be implemented to reduce the effects from background radiation without affecting the flow of traffic and the normal operation of the portal. Simple modifications include adding additional shielding to the environment, either inside or outside the apparatus. Previous work (2) has shown the utility of some of these shielding configurations for increasing the Signal to Noise Ratio (SNR) of gross-counting RPMs. Because the total cost for purchasing and installing RPM systems can be quite expensive, in the range of hundreds of thousands of dollars for each cargo-screening installation, these shielding variations may offer increases in detection capability for relatively small cost. Several modifications are considered here in regard to their real-world applicability, and are meant to give a general idea of the effectiveness of the schemes used to reduce background for both gross-counting and spectroscopic detectors. These scenarios are modeled via the Monte-Carlo N-Particle (MCNP) code package (1) for ease of altering shielding configurations, as well as enacting unusual scenarios prior to prototyping in the field. The objective of this paper is to provide results representative of real modifications that could enhance the sensitivity of this, as well as the next generation of radiation detectors. The models used in this work were designed to provide the most general results for

  10. Evaluation of a method to shield a welding electron beam from magnetic interference

    Science.gov (United States)

    Wall, W. A.

    1976-01-01

    It is known that electron beams are easily deflected by magnetic and electrostatic fields. Therefore, to prevent weld defects, stray electromagnetic fields are avoided in electron beam welding chambers if at all possible. The successful results of tests conducted at MSFC to evaluate a simple magnetic shield made from steel tubing are reported. Tests indicate that this shield was up to 85 percent effective in reducing magnetic effects on the electron beam of a welding machine. In addition, residual magnetic fields within the shield were so nearly uniform that the net effect on the beam alignment was negligible. It is concluded that the shield, with the addition of a tungsten liner, could be used in production welding.

  11. Tracking the Shadows through GMRT D. Narasimha , N. Kanekar ...

    Indian Academy of Sciences (India)

    R. Narasimhan (Krishtel eMaging) 1461 1996 Oct 15 13:05:22

    Tracking the Shadows through GMRT. D. Narasimha. 1. , N. Kanekar. 2. & J. N. Chengalur. 2. 1Tata Institute of Fundamental Research, Mumbai 400 005. 2NCRA, Tata Institute of Fundamental Research, Pune 411 007. Abstract. The structures of faint high redshift galaxies cannot be observed directly. But if a luminous ...

  12. Shadow Formation at Preschool from a Socio-materiality Perspective

    Science.gov (United States)

    Impedovo, Maria Antonietta; Delserieys-Pedregosa, Alice; Jégou, Corinne; Ravanis, Konstantinos

    2017-06-01

    The paper is set in socio-material farming to offer a way of conceptualising actions and interactions of children in preschool involved in the understanding of scientific concepts. A model of early science education about the physical phenomena of shadow formation is implemented in group work in a French context. The research involved 44 children (13 females and 31 males) of 5-6 years old. The research design was organised in three video recording steps: pre-test, teaching session and post-test. We focus on the analysis of nine teaching sessions to investigate children's `understanding' of shadow formation. A descriptive and qualitative approach was used. In particular, we have identified three main categories (the interaction of the children with the tools, the embodiment and verbal dimension)—with respective indicators—to perform the analysis. From the results, all the categories explored seem to influence each other: all material, human and social dimensions contribute to the children's understanding of shadow formation. Also we have identified some elements that can serve as a potential source of improvement of the teaching session on shadow formation. Finally, the research provides insights on how to improve science activities in preschool with the aim of supporting early understanding of physical phenomena.

  13. Estimating Outdoor Illumination Conditions Based on Detection of Dynamic Shadows

    DEFF Research Database (Denmark)

    Madsen, Claus B.; Lal, Brajesh Behari

    2013-01-01

    into the image stream to achieve realistic Augmented Reality where the shading and the shadowing of virtual objects is consistent with the real scene. Other techniques require the presence of a known object, a light probe, in the scene for estimating illumination. The technique proposed here works in general...

  14. Three-Dimensional Reconstruction Optical System Using Shadows Triangulation

    Science.gov (United States)

    Barba, J. Leiner; Vargas, Q. Lorena; Torres, M. Cesar; Mattos, V. Lorenzo

    2008-04-01

    In this work is developed a three-dimensional reconstruction system using the Shades3D tool of the Matlab® Programming Language and materials of low cost, such as webcam camera, a stick, a weak structured lighting system composed by a desk lamp, and observation plane in which the object is located. The reconstruction is obtained through a triangulation process that is executed after acquiring a sequence of images of the scene with a shadow projected on the object; additionally an image filtering process is done for obtaining only the part of the scene that will be reconstructed. Previously, it is necessary to develop a calibration process for determining the internal camera geometric and optical characteristics (intrinsic parameters), and the 3D position and orientation of the camera frame relative to a certain world coordinate system (extrinsic parameters). The lamp and the stick are used to produce a shadow which scans the object; in this technique, it is not necessary to know the position of the light source, instead the triangulation is obtained using shadow plane produced by intersection between the stick and the illumination pattern. The webcam camera captures all images with the shadow scanning the object, and Shades3D tool processes all information taking into account captured images and calibration parameters. Likewise, this technique is evaluated in the reconstruction of parts of the human body and its application in the detection of external abnormalities and elaboration of prosthesis or implant.

  15. Physician shadowing by college students: what do patients think?

    Science.gov (United States)

    Bing-You, Robert G; Hayes, Victoria M; Skolfield, Jennifer L

    2014-03-14

    The objective of this study is to determine patients' perceptions of physician shadowing by college students. Thirty-two patients who agreed to have a college student shadow their physician participated in semi-structured interviews during July and August 2013 at two outpatient family medicine centers. Qualitative techniques were utilized to analyze the transcripts of the patient interviews and identify common themes. The majority of patients (78.1%) felt the college student had a neutral effect on their visit and denied having concerns about confidentiality (87.5%). No patient felt that having the college student present affected their ability to maintain a trusting relationship with their physician. Three themes emerged from the qualitative analysis: benefits to students, willing participation and sensitive issues. Most patients (78.5%) recognized that the student was in college or was a premedical student. The overwhelming majority of patients stated that they would have a college student shadow their physician again in the future. Despite concerns raised by other authors about the possible negative effects of physician shadowing by college students, this study shows that patients feel the impact to be primarily neutral and that there are many perceived benefits to both student and patient.

  16. Shadow Capital: The Democratization of College Preparatory Education

    Science.gov (United States)

    Cipollone, Kristin; Stich, Amy E.

    2017-01-01

    In this article, we examine the manifestation and consequences of shadow capital within two public, urban, nonselective, college preparatory-designated high schools serving exclusively nondominant students. Informed by three years of ethnographic data, we argue that the transference of a historically elite college preparatory education from…

  17. On Risk Charges and Shadow Account Options in Pension Funds

    DEFF Research Database (Denmark)

    Jørgensen, Peter Løchte; Gatzert, Nadine

    This paper studies the economic implications of regulatory systems which allow equityholders of pension companies to not only charge a specific premium to compensate them for their higher risk (compared to policyholders), but also to accumulate these risk charges in a so-called shadow account in ...

  18. Assessment of multipath and shadowing effects on UHF band in ...

    African Journals Online (AJOL)

    In this work, the multi-path and shadowing effects on signal impairment were investigated through the use of empirical and semi-empirical path loss models analysis in built-up environments. Electromagnetic field strength measurements were conducted using four television transmitters at UHF bands along four major routes ...

  19. Perspective: Dynamic Shadowing Growth and its Energy Applications

    Directory of Open Access Journals (Sweden)

    Yiping eZhao

    2014-09-01

    Full Text Available The unique features of dynamic shadowing growth (DSG in structural and compositional design of nanomaterials are discussed. Their recent applications in energy storage, fuel cell, and solar energy conversion have been reviewed briefly. Future directions for applying DSG nanostructures in renewable energy applications are presented.

  20. EFFECT OF SHADOWING AND MULTIPATH FADING ON THE ...

    African Journals Online (AJOL)

    irrespective of their location. The traditional macro-only network have been proved ineffective when communication signal is required for users located in the cell edge and a certain distance away from the macrocell base station. This is because of excess attenuation of the signal due to fading and shadowing. Multipath ...

  1. Wake models developed during the Wind Shadow Project

    DEFF Research Database (Denmark)

    Larsen, Søren Ejling; Ott, Søren; Pena Diaz, Alfredo

    The Wind Shadow project has developed and validated improved models for determining the wakes losses, and thereby the array efficiency of very large, closely packed wind farms. The rationale behind the project has been that the existing software has been covering these types of wind farms poorly...

  2. Infrasound propagation in tropospheric ducts and acoustic shadow zones.

    Science.gov (United States)

    de Groot-Hedlin, Catherine D

    2017-10-01

    Numerical computations of the Navier-Stokes equations governing acoustic propagation are performed to investigate infrasound propagation in the troposphere and into acoustic shadow zones. An existing nonlinear finite-difference, time-domain (FDTD) solver that constrains input sound speed models to be axisymmetric is expanded to allow for advection and rigid, stair-step topography. The FDTD solver permits realistic computations along a given azimuth. It is applied to several environmental models to examine the effects of nonlinearity, topography, advection, and two-dimensional (2D) variations in wind and sound speeds on the penetration of infrasound into shadow zones. Synthesized waveforms are compared to a recording of a rocket motor fuel elimination event at the Utah Test and Training Range. Results show good agreement in the amplitude, duration, and spectra of synthesized and recorded waveforms for propagation through 2D atmospheric models whether or not topography, advection, or nonlinearity is explicitly included. However, infrasound propagation through a one-dimensional, range-averaged, atmospheric model yields waveforms with lower amplitudes and frequencies, suggesting that small-scale atmospheric variability causes significant scatter within the troposphere, leading to enhanced infrasound penetration into shadow zones. Thus, unresolved fine-scale atmospheric dynamics are not required to explain infrasound propagation into shadow zones.

  3. Shadow-Based Vehicle Detection in Urban Traffic

    Directory of Open Access Journals (Sweden)

    Manuel Ibarra-Arenado

    2017-04-01

    Full Text Available Vehicle detection is a fundamental task in Forward Collision Avoiding Systems (FACS. Generally, vision-based vehicle detection methods consist of two stages: hypotheses generation and hypotheses verification. In this paper, we focus on the former, presenting a feature-based method for on-road vehicle detection in urban traffic. Hypotheses for vehicle candidates are generated according to the shadow under the vehicles by comparing pixel properties across the vertical intensity gradients caused by shadows on the road, and followed by intensity thresholding and morphological discrimination. Unlike methods that identify the shadow under a vehicle as a road region with intensity smaller than a coarse lower bound of the intensity for road, the thresholding strategy we propose determines a coarse upper bound of the intensity for shadow which reduces false positives rates. The experimental results are promising in terms of detection performance and robustness in day time under different weather conditions and cluttered scenarios to enable validation for the first stage of a complete FACS.

  4. Seri Rama: converting a shadow play puppet to Street Fighter.

    Science.gov (United States)

    Ghani, D B A

    2012-01-01

    Shadow puppet plays, a traditional Malaysian theater art, is slowly losing its appeal to adolescents, who prefer computer games. To help reverse this decline, the authors incorporated the traditional Seri Rama character into the Street Fighter video game. Using modeling, texturing, and animation, they developed a 3D Seri Rama prototype. Users can control Seri Rama with a PlayStation game controller.

  5. Shadowing: Who Benefits and How? Uncovering a Booming EFL Teaching Technique for Listening Comprehension

    Science.gov (United States)

    Hamada, Yo

    2016-01-01

    This study examines common claims associated with shadowing. Studies in Japan conclude that shadowing is effective for improving learners' listening skills. Two common claims are that shadowing is effective for lower-proficiency learners and that it enhances learners' phoneme perception, thus improving listening comprehension skills. The former…

  6. Radiation shielding activities at IDOM

    International Nuclear Information System (INIS)

    Ordóñez, César Hueso; Gurpegui, Unai Cano; Valiente, Yelko Chento; Poveda, Imanol Zamora

    2017-01-01

    When human activities have to be performed under ionising radiation environments the safety of the workers must be guaranteed. Usually three principles are used to accomplish with ALARA (As Low As Reasonably Achievable) requirements: the more distance between the source term and the worker, the better; the less time spent to arrange any task, the better; and, once the previous principles are optimized should the exposure of the workers continues being above the regulatory limits, shielding has to be implemented. Through this paper some different examples of IDOM's shielding design activities are presented. Beginning with the gamma collimators for the Jules Horowitz Reactor, nuclear fuel's behaviour researching facility, where the beam path crosses the reactor's containment walls and is steered up to a gamma detector where the fuel spectrum is analysed and where the beam has to be attenuated several orders of magnitude in a short distance. Later it is shown IDOM’s approach for the shielding of the Emergency Control Management Center of Asociación Nuclear Ascó-Vandellòs-II NPPs, a bunker designed to withstand severe accident conditions and to support the involved staff during 30 days, considering the outside radioactive cloud and the inside source term that filtering units become as they filter the incoming air. And finally, a general approach to this kind of problems is presented, since the study of the source term considering all the possible contributions, passing through the material selection and the thicknesses calculation until the optimization of the materials. (author)

  7. Shielded room measurements, Final report

    Energy Technology Data Exchange (ETDEWEB)

    Stanton, J.S.

    1949-02-22

    The attenuation of electro-statically and electro-magnetically shielded rooms in the ``E,`` ``R,`` ``I,`` and ``T`` Buildings was measured so that corrective measure could be taken if the attenuation was found to be low. If remedial measures could not be taken, the shortcomings of the rooms would be known. Also, the men making the measurements should oversee construction and correct errors at the time. The work was performed by measuring the attenuation at spot frequencies over the range of from 150 kilocycles to 1280 megacycles with suitable equipment mounted in small rubber-tried trucks. The attenuation was determined by ``before and after`` shielding and/or ``door open and door closed`` measurements after installation of copper shielding. In general, attenuation in the frequency range of approximately 10 to 150 mc. was good and was of the order expected. At frequencies in the range of 150 mc. to 1280 mc., the attenuation curve was more erratic; that is, at certain frequencies a severe loss of attenuation was noted, while at others, the attenuation was very good. This was mainly due to poor or faulty seals around doors and pass windows. These poor seals existed in the ``T,`` ``E,`` and ``I`` Buildings because the doors were fitted improperly and somewhat inferior material was used. By experience from these difficulties, both causes were corrected in the ``R`` Building, which resulted in the improvement of the very high frequency (v.h.f.) range in this building. In some specific cases, however, the results were about the same. For the range of frequencies below approximately 10 mc., the attenuation, in almost all cases, gradually decreased as the frequency decreased and reached a minimum at .3 to 1.0 mc. This loss of attenuation was attributed to multiple grounding caused by moisture in the insulating timbers and will gradually decrease as the wood dries out.

  8. Radiation shielding activities at IDOM

    Energy Technology Data Exchange (ETDEWEB)

    Ordóñez, César Hueso; Gurpegui, Unai Cano; Valiente, Yelko Chento; Poveda, Imanol Zamora, E-mail: cesar.hueso@idom.com [IDOM, Consulting, Engineering and Architecture, S.A.U, Vizcaya (Spain)

    2017-07-01

    When human activities have to be performed under ionising radiation environments the safety of the workers must be guaranteed. Usually three principles are used to accomplish with ALARA (As Low As Reasonably Achievable) requirements: the more distance between the source term and the worker, the better; the less time spent to arrange any task, the better; and, once the previous principles are optimized should the exposure of the workers continues being above the regulatory limits, shielding has to be implemented. Through this paper some different examples of IDOM's shielding design activities are presented. Beginning with the gamma collimators for the Jules Horowitz Reactor, nuclear fuel's behaviour researching facility, where the beam path crosses the reactor's containment walls and is steered up to a gamma detector where the fuel spectrum is analysed and where the beam has to be attenuated several orders of magnitude in a short distance. Later it is shown IDOM’s approach for the shielding of the Emergency Control Management Center of Asociación Nuclear Ascó-Vandellòs-II NPPs, a bunker designed to withstand severe accident conditions and to support the involved staff during 30 days, considering the outside radioactive cloud and the inside source term that filtering units become as they filter the incoming air. And finally, a general approach to this kind of problems is presented, since the study of the source term considering all the possible contributions, passing through the material selection and the thicknesses calculation until the optimization of the materials. (author)

  9. Magnetic shielding of a limiter

    International Nuclear Information System (INIS)

    Brevnov, N.N.; Stepanov, S.B.; Khimchenko, L.N.; Matthews, G.F.; Goodal, D.H.J.

    1991-01-01

    Localization of plasma interaction with material surfaces in a separate chamber, from where the escape of impurities is hardly realized, i.e. application of magnetic divertors or pump limiters, is the main technique for reduction of the impurity content in a plasma. In this case, the production of a divertor configuration requires a considerable power consumption and results in a less effective utilization of the magnetic field volume. Utilization of a pump limiter, for example the ICL-type, under tokamak-reactor conditions would result in the extremely high and forbidden local heat loadings onto the limiter surface. Moreover, the magnetically-shielded pump limiter (MSL) was proposed to combine positive properties of the divertor and the pump limiter. The idea of magnetic shielding is to locate the winding with current inside the limiter head so that the field lines of the resultant magnetic field do not intercept the limiter surface. In this case the plasma flows around the limiter leading edges and penetrates into the space under the limiter. The shielding magnetic field can be directed either counter the toroidal field or counter the poloidal one of a tokamak, dependent on the concrete diagram of the device. Such a limiter has a number of advantages: -opportunity to control over the particle and impurity recycling without practical influence upon the plasma column geometry, - perturbation of a plasma column magnetic configuration from the side of such a limiter is less than that from the side of the divertor coils. The main deficiency is the necessity to locate active windings inside the discharge chamber. (author) 5 refs., 3 figs

  10. The Shadow Knows: Using Shadows to Investigate the Structure of the Pretransitional Disk of HD 100453

    Energy Technology Data Exchange (ETDEWEB)

    Long, Zachary C.; Fernandes, Rachel B.; Sitko, Michael [Department of Physics, University of Cincinnati, Cincinnati, OH 45221 (United States); Wagner, Kevin [Department of Astronomy/Steward Observatory, The University of Arizona, 933 North Cherry Avenue, Tucson, AZ 85721 (United States); Muto, Takayuki [Division of Liberal Arts, Kogakuin University, 1-24-2 Nishi-Shinjuku, Shinjuku-ku, Tokyo, 163-8677 (Japan); Hashimoto, Jun; Oh, Daehyon; Tamura, Motohide; Yang, Yi [National Astronomical Observatory of Japan, 2-21-1, Osawa, Mitaka, Tokyo, 181-8588 (Japan); Follette, Katherine [Kavli Institute for Particle Astrophysics and Cosmology, Stanford University, Stanford, CA 94305 (United States); Grady, Carol A. [Eureka Scientific, 2452 Delmer Street, Suite 100, Oakland CA 96402 (United States); Fukagawa, Misato [Division of Particle and Astrophysical Science, Graduate School of Science, Nagoya University, Nagoya (Japan); Hasegawa, Yasuhiro [Jet Propulsion Laboratory, California Institute of Technology, Pasadena, CA 91109 (United States); Kluska, Jacques; Kraus, Stefan [University of Exeter Astrophysics Group, School of Physics, Stocker Road, Exeter, Devon EX4 4QL (United Kingdom); Mayama, Satoshi [Department of Astronomical Science, The Graduate University for Advanced Studies (SOKENDAI), Shonan Village, Hayama, Kanagawa 240-0193 (Japan); McElwain, Michael W. [Exoplanets and Stellar Astrophysics Laboratory, Code 667, NASA’s Goddard Space Flight Center, Greenbelt, MD 20771 (United States); Uyama, Taichi [Department of Astronomy and RESCUE, The University of Tokyo, 7-3-1, Hongo, Bunkyo-ku, Tokyo, 113-0033 (Japan); Wisniewski, John P. [Homer L. Dodge Department of Physics, University of Oklahoma, Norman, OK 73071 (United States)

    2017-03-20

    We present Gemini Planet Imager polarized intensity imagery of HD 100453 in Y , J , and K 1 bands that reveals an inner gap (9–18 au), an outer disk (18–39 au) with two prominent spiral arms, and two azimuthally localized dark features that are also present in Spectro-Polarimetric High-contrast Exoplanet REsearch (SPHERE) total intensity images. Spectral energy distribution fitting further suggests that the radial gap extends to 1 au. The narrow, wedge-like shape of the dark features appears similar to predictions of shadows cast by an inner disk that is misaligned with respect to the outer disk. Using the Monte Carlo radiative transfer code HOCHUNCK3D, we construct a model of the disk that allows us to determine its physical properties in more detail. From the angular separation of the features, we measure the difference in inclination between the disks (45°) and their major axes, PA = 140° east of north for the outer disk, and 100° for the inner disk. We find an outer-disk inclination of 25° ± 10° from face-on, in broad agreement with the Wagner et al. measurement of 34°. SPHERE data in J and H bands indicate a reddish disk, which indicates that HD 100453 is evolving into a young debris disk.

  11. Dynamic rotating-shield brachytherapy

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Yunlong [Department of Electrical and Computer Engineering, University of Iowa, 4016 Seamans Center, Iowa City, Iowa 52242 (United States); Flynn, Ryan T.; Kim, Yusung [Department of Radiation Oncology, University of Iowa, 200 Hawkins Drive, Iowa City, Iowa 52242 (United States); Yang, Wenjun [Department of Medical Physics, University of Wisconsin-Madison, 1111 Highland Avenue, Madison, Wisconsin 53705 (United States); Wu, Xiaodong [Department of Electrical and Computer Engineering, University of Iowa, 4016 Seamans Center, Iowa City, Iowa 52242 and Department of Radiation Oncology, University of Iowa, 200 Hawkins Drive, Iowa City, Iowa 52242 (United States)

    2013-12-15

    Purpose: To present dynamic rotating shield brachytherapy (D-RSBT), a novel form of high-dose-rate brachytherapy (HDR-BT) with electronic brachytherapy source, where the radiation shield is capable of changing emission angles during the radiation delivery process.Methods: A D-RSBT system uses two layers of independently rotating tungsten alloy shields, each with a 180° azimuthal emission angle. The D-RSBT planning is separated into two stages: anchor plan optimization and optimal sequencing. In the anchor plan optimization, anchor plans are generated by maximizing the D{sub 90} for the high-risk clinical-tumor-volume (HR-CTV) assuming a fixed azimuthal emission angle of 11.25°. In the optimal sequencing, treatment plans that most closely approximate the anchor plans under the delivery-time constraint will be efficiently computed. Treatment plans for five cervical cancer patients were generated for D-RSBT, single-shield RSBT (S-RSBT), and {sup 192}Ir-based intracavitary brachytherapy with supplementary interstitial brachytherapy (IS + ICBT) assuming five treatment fractions. External beam radiotherapy doses of 45 Gy in 25 fractions of 1.8 Gy each were accounted for. The high-risk clinical target volume (HR-CTV) doses were escalated such that the D{sub 2cc} of the rectum, sigmoid colon, or bladder reached its tolerance equivalent dose in 2 Gy fractions (EQD2 with α/β= 3 Gy) of 75 Gy, 75 Gy, or 90 Gy, respectively.Results: For the patients considered, IS + ICBT had an average total dwell time of 5.7 minutes/fraction (min/fx) assuming a 10 Ci{sup 192}Ir source, and the average HR-CTV D{sub 90} was 78.9 Gy. In order to match the HR-CTV D{sub 90} of IS + ICBT, D-RSBT required an average of 10.1 min/fx more delivery time, and S-RSBT required 6.7 min/fx more. If an additional 20 min/fx of delivery time is allowed beyond that of the IS + ICBT case, D-RSBT and S-RSBT increased the HR-CTV D{sub 90} above IS + ICBT by an average of 16.3 Gy and 9.1 Gy, respectively

  12. Irrigoscopy - irrigography method, dosimetry and radiation shielding

    International Nuclear Information System (INIS)

    Zubanov, Z.; Kolarevic, G.

    1999-01-01

    Use of patient's radiation shielding during radiology diagnostic procedures in our country is insufficiently represent, so patients needlessly receive very high entrance skin doses in body areas which are not in direct x-ray beam. During irrigoscopy, patient's radiation shielding is very complex problem, because of the organs position. In the future that problem must be solved. We hope that some of our suggestions about patient's radiation shielding during irrigoscopy, can be a small step in that way. (author)

  13. Isotopic age of enderbites of Ukrainian shield

    International Nuclear Information System (INIS)

    Bartnitskij, E.N.; Bojko, V.L.; Levkovskaya, N.Yu.; Lesnaya, I.M.; Siroshtan, R.I.; Sharkin, O.P.

    1987-01-01

    Results of determining U-Pb isotopic age of accessory zircons from enderbites of Azov, Dniestrovo-Bug and Ingulo-Ingultsk regions of the Ukrainian shield are presented. The isotopic age values obtained make up from 3400 millions of years for enderbites of Novo-Pavlovsk complex of the Ukrainian shield up to 2100 millions of years for enderbites and charnockites of Berdichev complex. So, enderbites of both Archean and Proterozoic age are found in the Ukrainian shield area which points out to diversification of granulites metamorphism manifestation in various blocks of the Ukrainian shield

  14. Problems of the power plant shield optimization

    International Nuclear Information System (INIS)

    Abagyan, A.A.; Dubinin, A.A.; Zhuravlev, V.I.; Kurachenko, Yu.A.; Petrov, Eh.E.

    1981-01-01

    General approaches to the solution of problems on the nuclear power plant radiation shield optimization are considered. The requirements to the shield parameters are formulated in a form of restrictions on a number of functionals, determined by the solution of γ quantum and neutron transport equations or dimensional and weight characteristics of shield components. Functional determined by weight-dimensional parameters (shield cost, mass and thickness) and functionals, determined by radiation fields (equivalent dose rate, produced by neutrons and γ quanta, activation functional, radiation functional, heat flux, integral heat flux in a particular part of the shield volume, total energy flux through a particular shield surface are considered. The following methods of numerical solution of simplified optimization problems are discussed: semiempirical methods using radiation transport physical leaks, numerical solution of approximate transport equations, numerical solution of transport equations for the simplest configurations making possible to decrease essentially a number of variables in the problem. The conclusion is drawn that the attained level of investigations on the problem of nuclear power plant shield optimization gives the possibility to pass on at present to the solution of problems with a more detailed account of the real shield operating conditions (shield temperature field account, its strength and other characteristics) [ru

  15. Radiation dose reduction by water shield

    International Nuclear Information System (INIS)

    Zeb, J.; Arshed, W.; Ahmad, S.S.

    2007-06-01

    This report is an operational manual of shielding software W-Shielder, developed at Health Physics Division (HPD), Pakistan Institute of Nuclear Science and Technology (PINSTECH), Pakistan Atomic Energy Commission. The software estimates shielding thickness for photons having their energy in the range 0.5 to 10 MeV. To compute the shield thickness, self absorption in the source has been neglected and the source has been assumed as a point source. Water is used as a shielding material in this software. The software is helpful in estimating the water thickness for safe handling, storage of gamma emitting radionuclide. (author)

  16. Optimization of the CMS forward shielding

    CERN Document Server

    Huhtinen, Mika

    2000-01-01

    A first realistic version of the CMS forward shielding was presented in the 1999 Engineering Design Review. It was discovered that the background increased by a factor of 2 with respect to the TDR where an idealized shielding had been assumed. This note describes the optimizations implemented in the realistic shielding with the aim to recover the TDR performance. An optimization of the shielding geometry, the beam pipe and a filling of major cracks has allowed to achieve the goal. Although the differences to the TDR are very minor, these new calculations should be understood as an update to those presented in the TDR.

  17. TPX remote maintenance and shielding

    International Nuclear Information System (INIS)

    Rennich, M.J.; Nelson, B.E.

    1994-01-01

    The Tokamak Physics Experiment machine design incorporates comprehensive planning for efficient and safe component maintenance. Three programmatic decisions have been made to insure the successful implementation of this objective. First, the tokamak incorporates radiation shielding to reduce activation of components and limit the dose rate to personnel working on the outside of the machine. This allows most of the ex-vessel equipment to be maintained through conventional ''hands-on'' procedures. Second, to the maximum extent possible, low activation materials will be used inside the shielding volume. This resulted in the selection of Titanium (Ti-6Al-4V) for the vacuum vessel and PFC structures. The third decision stipulated that the primary in-vessel components will be replaced or repaired via remote maintenance tools specifically provided for the task. The component designers have been given the responsibility of incorporating maintenance design and for proving the maintainability of the design concepts in full-scale mockup tests prior to the initiation of final fabrication. Remote maintenance of the TPX machine is facilitated by general purpose tools provided by a special purpose design team. Major tools will include an in-vessel transporter, a vessel transfer system and a large component transfer container. In addition, tools such as manipulators and remotely operable impact wrenches will be made available to the component designers by this group. Maintenance systems will also provide the necessary controls for this equipment

  18. Channels in tokamak reactor shields

    International Nuclear Information System (INIS)

    Shchipakin, O.L.

    1981-01-01

    The results of calculations of neutron transport through the channels in the tokamak reactor radiation shields, obtained by the Monte Carlo method and by the method of discrete ordinates, are considered. The given data show that the structural materials of the channel and that of the blanket and shields in the regions close to it are subjected to almost the same irradiation as the first wall and therefore they should satisfy the technical requirements. The radiation energy release in the injector channel wall, caused by neutron shooting, substantially depends on the channel dimensions. At the channel large diameter (0.7-10 m) this dependence noticeably decreases. The investigation of the effect of the injector channel cross section form on the neutron flux density through the channel, testifies to weak dependence of shooting radiation intensity on the form of the channel cross section. It is concluded that measures to decrease unfavourable effect of the channels on the safety of the power tokamak reactor operation and maintenance cause substantial changes in reactor design due to which the channel protection must be developed at first stages. The Monte Carlo method is recommended to be used for variant calculations and when calculating the neutron flux functionals in specific points of the system the discrete ordinate method is preferred [ru

  19. Isotope effects on nuclear shielding

    International Nuclear Information System (INIS)

    Hansen, P.E.

    1983-01-01

    This review concentrates upon empirical trends and practical uses of mostly secondary isotope effects, both of the intrinsic and equilibrium types. The text and the tables are arranged in the following fashion. The most 'popular' isotope effect is treated first, deuterium isotope effects on 13 C nuclear shielding, followed by deuterium on 1 H nuclear shieldings, etc. Focus is thus on the isotopes producing the effect rather than on the nuclei suffering the effect. After a brief treatment of each type of isotope effect, general trends are dealt with. Basic trends of intrinsic isotope effects such as additivity, solvent effects, temperature effects, steric effects, substituent effects and hyperconjugation are discussed. Uses of isotope effects for assignment purposes, in stereochemical studies, in hydrogen bonding and in isotopic tracer studies are dealt with. Kinetic studies, especially of phosphates, are frequently performed by utilizing isotope effects. In addition, equilibrium isotope effects are treated in great detail as these are felt to be new and very important and may lead to new uses of isotope effects. Techniques used to obtain isotope effects are briefly surveyed at the end of the chapter. (author)

  20. Continuous electrodeionization through electrostatic shielding

    International Nuclear Information System (INIS)

    Dermentzis, Konstantinos

    2008-01-01

    We report a new continuous electrodeionization cell with electrostatically shielded concentrate compartments or electrochemical Faraday cages formed by porous electronically and ionically conductive media, instead of permselective ion exchange membranes. Due to local elimination of the applied electric field within the compartments, they electrostatically retain the incoming ions and act as 'electrostatic ion pumps' or 'ion traps' and therefore concentrate compartments. The porous media are chemically and thermally stable. Electrodeionization or electrodialysis cells containing such concentrate compartments in place of ion exchange membranes can be used to regenerate ion exchange resins and produce deionized water, to purify industrial effluents and desalinate brackish or seawater. The cells can work by polarity reversal without any negative impact to the deionization process. Because the electronically and ionically active media constituting the electrostatically shielded concentrate compartments are not permselective and coions are not repelled but can be swept by the migrating counterions, the cells are not affected by the known membrane associated limitations, such as concentration polarization or scaling and show an increased current efficiency

  1. Effects of scattering anisotropy approximation in multigroup radiation shielding calculations

    International Nuclear Information System (INIS)

    Altiparmakov, D.

    1983-01-01

    Expansion of the scattering cross sections into Legendre series is the usual way of solving neutron transport problems. Because of the large space gradients of the neutron flux, the effects of that approximation become especially remarkable in the radiation shielding calculations. In this paper, a method taking into account the scattering anisotropy is presented. From the point od view of the accuracy and computing rate, the optimal approximation of the scattering anisotropy is established for the basic protective materials on the basis of simple problem calculations. (author)

  2. A Soft Shadow Detection Method Based on MRF for Remote Sensing Images

    Directory of Open Access Journals (Sweden)

    Pengwei Li

    2015-01-01

    Full Text Available Shadows limit many remote sensing applications such as classification, target detection, and change detection. Most current shadow detection methods utilize the histogram threshold of spectral characteristics to distinguish the shadows and nonshadows directly, called “hard binary shadow.” Obviously, the performance of threshold-based methods heavily rely on the selected threshold. Simultaneously, these threshold-based methods do not take any spatial information into account. To overcome these shortcomings, a soft shadow description method is developed by introducing the concept of opacity into shadow detection, and MRF-based shadow detection method is proposed in order to make use of neighborhood information. Experiments on remote sensing images have shown that the proposed method can obtain more accurate detection results.

  3. Determinants of the Shadow Economy in the Czech Regions: A Region-Level Study

    Directory of Open Access Journals (Sweden)

    Buček Jakub

    2017-09-01

    Full Text Available This paper investigates the size and development of the shadow economy in the Czech Republic on the state-level base over the 2005-2014 period. The multiple indicators multiple causes (MIMIC model is used to assess the estimation of the shadow economy size. I investigate how labour market, number of people with at least one distraint, and the burden of taxation might contribute to the existence of the shadow economy. While the former two are important determinants of the shadow economy, I find no evidence to prove any significant impact of distraints on the shadow economy size. As for the country’s particular regions, I find that those surrounding big cities, especially Prague, have, on average, a smaller shadow economy size, whereas regions in the borderlands (former Sudetenland suffer from a larger shadow economy.

  4. Shadow casted by a Konoplya-Zhidenko rotating non-Kerr black hole

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Mingzhi; Chen, Songbai; Jing, Jiliang, E-mail: wmz9085@126.com, E-mail: csb3752@hunnu.edu.cn, E-mail: jljing@hunnu.edu.cn [Institute of Physics and Department of Physics, Hunan Normal University, Changsha, Hunan 410081 (China)

    2017-10-01

    We have investigated the shadow of a Konoplya-Zhidenko rotating non-Kerr black hole with an extra deformation parameter. The spacetime structure arising from the deformed parameter affects sharply the black hole shadow. With the increase of the deformation parameter, the size of the shadow of black hole increase and its shape becomes more rounded for arbitrary rotation parameter. The D-shape shadow of black hole emerges only in the case a <2√3/3\\, M with the proper deformation parameter. Especially, the black hole shadow possesses a cusp shape with small eye lashes in the cases with a >M, and the shadow becomes less cuspidal with the increase of the deformation parameter. Our result show that the presence of the deformation parameter yields a series of significant patterns for the shadow casted by a Konoplya-Zhidenko rotating non-Kerr black hole.

  5. Riddles in the Dark: Imaging Inside Mercury's Permanently Shadowed Craters

    Science.gov (United States)

    Ernst, C. M.; Chabot, N. L.; Denevi, B. W.; Nair, H.; Deutsch, A. N.; Murchie, S. L.; Robinson, M. S.; Blewett, D. T.; Head, J. W.; Harmon, J. K.; Neumann, G. A.; Solomon, S. C.

    2013-12-01

    Numerous lines of evidence independently point to the presence of water ice in Mercury's polar regions: Earth-based radar shows radar-bright regions; Mariner 10 and MESSENGER Mercury Dual Imaging System (MDIS) images reveal that these regions are permanently (south polar region) or persistently (north polar region) shadowed; neutron spectrometry indicates hydrogen-rich material; thermal models support the presence of water ice; and Mercury Laser Altimeter (MLA) reflectance measurements at 1064 nm show high and low reflectance deposits consistent in location to where models predict surface and buried water ice, respectively. Throughout 2013, MESSENGER executed a campaign dedicated to imaging the permanently shadowed crater floors of Mercury's north polar region using sunlight scattered from nearby terrain. The campaign makes use of the broadband clear filter (central wavelength 700 nm, bandwidth 600 nm) of the MDIS wide-angle camera (WAC) to target and image radar-bright areas within all host craters > 10 km in diameter under multiple lighting conditions. To date, MESSENGER has imaged the interiors of nearly 20 craters that host radar-bright deposits, including the largest such deposits near the north pole that are likely to host surface water ice. The images reveal a variety of surface morphologies, ranging from the smooth crater floor of the fresh Kandinsky crater, to the moderately cratered floor of Tolkien crater, and to the battered floor of Prokofiev crater, in which the permanently shadowed region does not differ morphologically from the rest of the crater floor. Thus, no distinct morphology is identified in association with polar deposits, and craters hosting such material span the typical range of degradation states relative to their illuminated counterparts. MDIS images also reveal albedo differences in craters with floors not fully in permanent shadow. Prokofiev provides a special environment for viewing a radar- and MLA-bright region suspected to host

  6. Shadows and spirals in the protoplanetary disk HD 100453

    Science.gov (United States)

    Benisty, M.; Stolker, T.; Pohl, A.; de Boer, J.; Lesur, G.; Dominik, C.; Dullemond, C. P.; Langlois, M.; Min, M.; Wagner, K.; Henning, T.; Juhasz, A.; Pinilla, P.; Facchini, S.; Apai, D.; van Boekel, R.; Garufi, A.; Ginski, C.; Ménard, F.; Pinte, C.; Quanz, S. P.; Zurlo, A.; Boccaletti, A.; Bonnefoy, M.; Beuzit, J. L.; Chauvin, G.; Cudel, M.; Desidera, S.; Feldt, M.; Fontanive, C.; Gratton, R.; Kasper, M.; Lagrange, A.-M.; LeCoroller, H.; Mouillet, D.; Mesa, D.; Sissa, E.; Vigan, A.; Antichi, J.; Buey, T.; Fusco, T.; Gisler, D.; Llored, M.; Magnard, Y.; Moeller-Nilsson, O.; Pragt, J.; Roelfsema, R.; Sauvage, J.-F.; Wildi, F.

    2017-01-01

    Context. Understanding the diversity of planets requires studying the morphology and physical conditions in the protoplanetary disks in which they form. Aims: We aim to study the structure of the 10 Myr old protoplanetary disk HD 100453, to detect features that can trace disk evolution and to understand the mechanisms that drive these features. Methods: We observed HD 100453 in polarized scattered light with VLT/SPHERE at optical (0.6 μm, 0.8 μm) and near-infrared (1.2 μm) wavelengths, reaching an angular resolution of 0.02'', and an inner working angle of 0.09''. Results: We spatially resolve the disk around HD 100453, and detect polarized scattered light up to 0.42'' ( 48 au). We detect a cavity, a rim with azimuthal brightness variations at an inclination of 38° with respect to our line of sight, two shadows and two symmetric spiral arms. The spiral arms originate near the location of the shadows, close to the semi major axis. We detect a faint feature in the SW that can be interpreted as the scattering surface of the bottom side of the disk, if the disk is tidally truncated by the M-dwarf companion currently seen at a projected distance of 119 au. We construct a radiative transfer model that accounts for the main characteristics of the features with an inner and outer disk misaligned by 72°. The azimuthal brightness variations along the rim are well reproduced with the scattering phase function of the model. While spirals can be triggered by the tidal interaction with the companion, the close proximity of the spirals to the shadows suggests that the shadows could also play a role. The change in stellar illumination along the rim induces an azimuthal variation of the scale height that can contribute to the brightness variations. Conclusions: Dark regions in polarized images of transition disks are now detected in a handful of disks and often interpreted as shadows due to a misaligned inner disk. However, the origin of such a misalignment in HD 100453, and

  7. Analytical model for relativistic corrections to the nuclear magnetic shielding constant in atoms

    International Nuclear Information System (INIS)

    Romero, Rodolfo H.; Gomez, Sergio S.

    2006-01-01

    We present a simple analytical model for calculating and rationalizing the main relativistic corrections to the nuclear magnetic shielding constant in atoms. It provides good estimates for those corrections and their trends, in reasonable agreement with accurate four-component calculations and perturbation methods. The origin of the effects in deep core atomic orbitals is manifestly shown

  8. Analytical model for relativistic corrections to the nuclear magnetic shielding constant in atoms

    Energy Technology Data Exchange (ETDEWEB)

    Romero, Rodolfo H. [Facultad de Ciencias Exactas, Universidad Nacional del Nordeste, Avenida Libertad 5500 (3400), Corrientes (Argentina)]. E-mail: rhromero@exa.unne.edu.ar; Gomez, Sergio S. [Facultad de Ciencias Exactas, Universidad Nacional del Nordeste, Avenida Libertad 5500 (3400), Corrientes (Argentina)

    2006-04-24

    We present a simple analytical model for calculating and rationalizing the main relativistic corrections to the nuclear magnetic shielding constant in atoms. It provides good estimates for those corrections and their trends, in reasonable agreement with accurate four-component calculations and perturbation methods. The origin of the effects in deep core atomic orbitals is manifestly shown.

  9. Optically-transparent radiation-shielding composition

    International Nuclear Information System (INIS)

    Bolles, T.F.; Fleming, P.B.

    1976-01-01

    An optically transparent, essentially colorless radiation shielding material for high energy radiation contains a combination of lead or thallium salts of C 1 to C 5 organic acids and may contain lead or thallium salts of mineral acids. Shields of complex shapes are easily constructed

  10. Improvements in or relating to nuclear shields

    International Nuclear Information System (INIS)

    Hawkins, R.J.; Riley, K.; Powell, C.

    1981-01-01

    A nuclear radiation shield comprises two pieces of steel held together edge to edge by a weld, the depth of which is less than the thickness of either of the edges. As the radiaion shielding effect of the weld will be less than the steel, an insert is bolted or welded over the weld. (U.K.)

  11. Several problems in accelerator shielding study

    International Nuclear Information System (INIS)

    Nakamura, Takashi; Hirayama, Hideo; Ban, Shuichi.

    1980-01-01

    Recently, the utilization of accelerators has increased rapidly, and the increase of accelerating energy and beam intensity is also remarkable. The studies on accelerator shielding have become important, because the amount of radiation emitted from accelerators increased, the regulation of the dose of environmental radiation was tightened, and the cost of constructing shielding rose. As the plans of constructing large accelerators have been made successively, the survey on the present state and the problems of the studies on accelerator shielding was carried out. Accelerators are classified into electron accelerators and proton accelerators in view of the studies on shielding. In order to start the studies on accelerator shielding, first, the preparation of the cross section data is indispensable. The cross sections for generating Bremsstrahlung, photonuclear reactions generating neutrons, generation of neutrons by hadrons, nuclear reaction of neutrons and generation of gamma-ray by hadrons are described. The generation of neutrons and gamma-ray as the problems of thick targets is explained. The shielding problems are complex and diversified, but in this paper, the studies on the shielding, by which basic data are obtainable, are taken up, such as beam damping and side wall shielding. As for residual radioactivity, main nuclides and the difference of residual radioactivity according to substances have been studied. (J.P.N.)

  12. Actively shielded low level gamma - spectrometric system

    International Nuclear Information System (INIS)

    Mrdja, D.; Bikit, I.; Forkapic, S.; Slivka, J.; Veskovic, M.

    2005-01-01

    The results of the adjusting and testing of the actively shielded low level gamma-spectrometry system are presented. The veto action of the shield reduces the background in the energy region of 50 keV to the 2800 keV for about 3 times. (author) [sr

  13. Fundamental Parameters of the SHIELD II Galaxies

    Science.gov (United States)

    Cannon, John

    2014-10-01

    The "Survey of HI in Extremely Low-mass Dwarfs" ("SHIELD") is a multiwavelength, legacy-class observational campaign that is facilitating the study of both internal and global evolutionary processes in 12 low-mass dwarf galaxies discovered in early Arecibo Legacy Fast ALFA (ALFALFA) survey data products. Cycle 19 HST observations of the 12 SHIELD galaxies have allowed us to determine their TRGB distances, thus anchoring the physical scales on which our ongoing analysis is based. Since the inception of SHIELD, the ALFALFA survey has completed data acquisition, thereby populating the faint end of the HI mass function with dozens of SHIELD analogs. In this proposal we request ACS imaging of 18 of these "SHIELD II" galaxies that have already been imaged in the HI spectral line with the WSRT. These data will enable a holistic HST imaging study of the fundamental parameters and characteristics of a statistically robust sample of 30 extremely low-mass galaxies (including 12 SHIELD and 18 SHIELD II systems). The primary science goal is the derivation of TRGB distances; the distance dependence of many fundamental parameters makes HST observations critical for the success of SHIELD II. Additional science goals include an accurate census of the dark matter contents of these galaxies, a spatial and temporal study of star formation within them, and a characterization of the fundamental parameters that change as galaxy masses range from "mini-halo" to star-forming dwarf.

  14. Shielding effectiveness of superconductive particles in plastics

    International Nuclear Information System (INIS)

    Pienkowski, T.; Kincaid, J.; Lanagan, M.T.; Poeppel, R.B.; Dusek, J.T.; Shi, D.; Goretta, K.C.

    1988-09-01

    The ability to cool superconductors with liquid nitrogen instead of liquid helium has opened the door to a wide range of research. The well known Meissner effect, which states superconductors are perfectly diamagnetic, suggests shielding applications. One of the drawbacks to the new ceramic superconductors is the brittleness of the finished material. Because of this drawback, any application which required flexibility (e.g., wire and cable) would be impractical. Therefore, this paper presents the results of a preliminary investigation into the shielding effectiveness of YBa 2 Cu 3 O/sub 7-x/ both as a composite and as a monolithic material. Shielding effectiveness was measured using two separate test methods. One tested the magnetic (near field) shielding, and the other tested the electromagnetic (far field) shielding. No shielding was seen in the near field measurements on the composite samples, and only one heavily loaded sample showed some shielding in the far field. The monolithic samples showed a large amount of magnetic shielding. 5 refs., 5 figs

  15. Infrared shield facilitates optical pyrometer measurements

    Science.gov (United States)

    Eichenbrenner, F. F.; Illg, W.

    1965-01-01

    Water-cooled shield facilitates optical pyrometer high temperature measurements of small sheet metal specimens subjected to tensile stress in fatigue tests. The shield excludes direct or reflected radiation from one face of the specimen and permits viewing of the infrared radiation only.

  16. PC based temporary shielding administrative procedure (TSAP)

    Energy Technology Data Exchange (ETDEWEB)

    Olsen, D.E.; Pederson, G.E. [Sargent & Lundy, Chicago, IL (United States); Hamby, P.N. [Commonwealth Edison Co., Downers Grove, IL (United States)

    1995-03-01

    A completely new Administrative Procedure for temporary shielding was developed for use at Commonwealth Edison`s six nuclear stations. This procedure promotes the use of shielding, and addresses industry requirements for the use and control of temporary shielding. The importance of an effective procedure has increased since more temporary shielding is being used as ALARA goals become more ambitious. To help implement the administrative procedure, a personal computer software program was written to incorporate the procedural requirements. This software incorporates the useability of a Windows graphical user interface with extensive help and database features. This combination of a comprehensive administrative procedure and user friendly software promotes the effective use and management of temporary shielding while ensuring that industry requirements are met.

  17. Technology development for radiation shielding analysis

    International Nuclear Information System (INIS)

    Ha, Jung Woo; Lee, Jae Kee; Kim, Jong Kyung

    1986-12-01

    Radiation shielding analysis in nuclear engineering fields is an important technology which is needed for the calculation of reactor shielding as well as radiation related safety problems in nuclear facilities. Moreover, the design technology required in high level radioactive waste management and disposal facilities is faced on serious problems with rapidly glowing nuclear industry development, and more advanced technology has to be developed for tomorrow. The main purpose of this study is therefore to build up the self supporting ability of technology development for the radiation shielding analysis in order to achieve successive development of nuclear industry. It is concluded that basic shielding calculations are possible to handle and analyze by using our current technology, but more advanced technology is still needed and has to be learned for the degree of accuracy in two-dimensional shielding calculation. (Author)

  18. GFR Sub-Assembly Shielding Design Studies

    Energy Technology Data Exchange (ETDEWEB)

    J. R. Parry

    2006-01-01

    This report presents the methodology and results for a preliminary study for Gas-Cooled Fast Reactor (GFR) subassembly fast neutron shielding configurations. The purpose of the shielding in the subassembly is to protect reactor components from fast (E>0.1 MeV) neutrons. The subassembly is modeled in MCNP version 5 release 1.30. Parametric studies were performed varying the thickness of the shielding and calculating the fast neutron flux at the vessel head and the core grid plate. This data was used to determine the minimum thickness needed to protect the vessel head and the core grid plate. These thicknesses were used to analyze different shielding configurations incorporating coolant passages and also to estimate the neutron and photon energy deposition in the shielding material.

  19. PC based temporary shielding administrative procedure (TSAP)

    International Nuclear Information System (INIS)

    Olsen, D.E.; Pederson, G.E.; Hamby, P.N.

    1995-01-01

    A completely new Administrative Procedure for temporary shielding was developed for use at Commonwealth Edison's six nuclear stations. This procedure promotes the use of shielding, and addresses industry requirements for the use and control of temporary shielding. The importance of an effective procedure has increased since more temporary shielding is being used as ALARA goals become more ambitious. To help implement the administrative procedure, a personal computer software program was written to incorporate the procedural requirements. This software incorporates the useability of a Windows graphical user interface with extensive help and database features. This combination of a comprehensive administrative procedure and user friendly software promotes the effective use and management of temporary shielding while ensuring that industry requirements are met

  20. Practical radiation shielding for biomedical research

    International Nuclear Information System (INIS)

    Klein, R.C.; Reginatto, M.; Party, E.; Gershey, E.L.

    1990-01-01

    This paper reports on calculations which exist for estimating shielding required for radioactivity; however, they are often not applicable for the radionuclides and activities common in biomedical research. A variety of commercially available Lucite shields are being marketed to the biomedical community. Their advertisements may lead laboratory workers to expect better radiation protection than these shields can provide or to assume erroneously that very weak beta emitters require extensive shielding. The authors have conducted a series of shielding experiments designed to simulate exposures from the amounts of 32 P, 51 Cr and 125 I typically used in biomedical laboratories. For most routine work, ≥0.64 cm of Lucite covered with various thicknesses of lead will reduce whole-body occupational exposure rates of < 1mR/hr at the point of contact

  1. Prediction of melanoma metastasis by the Shields index based on lymphatic vessel density

    Directory of Open Access Journals (Sweden)

    Metcalfe Chris

    2010-05-01

    Full Text Available Abstract Background Melanoma usually presents as an initial skin lesion without evidence of metastasis. A significant proportion of patients develop subsequent local, regional or distant metastasis, sometimes many years after the initial lesion was removed. The current most effective staging method to identify early regional metastasis is sentinel lymph node biopsy (SLNB, which is invasive, not without morbidity and, while improving staging, may not improve overall survival. Lymphatic density, Breslow's thickness and the presence or absence of lymphatic invasion combined has been proposed to be a prognostic index of metastasis, by Shields et al in a patient group. Methods Here we undertook a retrospective analysis of 102 malignant melanomas from patients with more than five years follow-up to evaluate the Shields' index and compare with existing indicators. Results The Shields' index accurately predicted outcome in 90% of patients with metastases and 84% without metastases. For these, the Shields index was more predictive than thickness or lymphatic density. Alternate lymphatic measurement (hot spot analysis was also effective when combined into the Shields index in a cohort of 24 patients. Conclusions These results show the Shields index, a non-invasive analysis based on immunohistochemistry of lymphatics surrounding primary lesions that can accurately predict outcome, is a simple, useful prognostic tool in malignant melanoma.

  2. Radiation Shielding Systems Using Nanotechnology

    Science.gov (United States)

    Chen, Bin (Inventor); McKay, Christoper P. (Inventor)

    2011-01-01

    A system for shielding personnel and/or equipment from radiation particles. In one embodiment, a first substrate is connected to a first array or perpendicularly oriented metal-like fingers, and a second, electrically conducting substrate has an array of carbon nanostructure (CNS) fingers, coated with an electro-active polymer extending toward, but spaced apart from, the first substrate fingers. An electric current and electric charge discharge and dissipation system, connected to the second substrate, receives a current and/or voltage pulse initially generated when the first substrate receives incident radiation. In another embodiment, an array of CNSs is immersed in a first layer of hydrogen-rich polymers and in a second layer of metal-like material. In another embodiment, a one- or two-dimensional assembly of fibers containing CNSs embedded in a metal-like matrix serves as a radiation-protective fabric or body covering.

  3. Neutron shielding heat insulation material

    International Nuclear Information System (INIS)

    Aoki, Susumu; Asaumi, Hiroshi; Take, Shigeo; Miyakoshi, Jun-ichi; Takemoto, Hiroshi.

    1979-01-01

    Purpose: To improve decceleration and absorption of neutrons by incorporating neutron moderators and neutron absorbers in asbestos to thereby increase hydrogen concentration. Constitution: A mixture consisting of crysotile asbestos, surface active agent and water is well stirred and compounded to open the crysotile asbestos filaments and prepare a high viscosity slurry. After adding hydroxides such as magnesium hydroxide, hydrated salts such as magnesium borate hydrate or water containing minerals such as alumina cement hydrate, or boron compound to the slurry, the slurry is charged in a predetermined die, and dried and compressed to prepare shielding heat insulation products. The crysotile asbestos has 18 - 15 wt.% of water of crystallinity in the structure and contains a considerably high hydrogen concentration that acts as neutron moderators. (Kawakami, Y.)

  4. Valuing ecosystem services. A shadow price for net primary production

    International Nuclear Information System (INIS)

    Richmond, Amy; Kaufmann, Robert K.; Myneni, Ranga B.

    2007-01-01

    We analyze the contribution of ecosystem services to GDP and use this contribution to calculate an empirical price for ecosystem services. Net primary production is used as a proxy for ecosystem services and, along with capital and labor, is used to estimate a Cobb Douglas production function from an international panel. A positive output elasticity for net primary production probably measures both marketed and nonmarketed contributions of ecosystems services. The production function is used to calculate the marginal product of net primary production, which is the shadow price for ecosystem services. The shadow price generally is greatest for developed nations, which have larger technical scalars and use less net primary production per unit output. The rate of technical substitution indicates that the quantity of capital needed to replace a unit of net primary production tends to increase with economic development, and this rate of replacement may ultimately constrain economic growth. (author)

  5. X-Ray Shadowing Experiments Toward Infrared Dark Clouds

    Science.gov (United States)

    Anderson, L. E.; Snowden, S.; Bania, T. M.

    2009-01-01

    We searched for X-ray shadowing toward two infrared dark clouds (IRDCs) using the MOS detectors on XMM-Newton to learn about the Galactic distribution of X-ray emitting plasma. IRDCs make ideal X-ray shadowing targets of 3/4 keY photons due to their high column densities, relatively large angular sizes, and known kinematic distances. Here we focus on two clouds near 30 deg Galactic longitude at distances of 2 and 5 kpc from the Sun. We derive the foreground and background column densities of molecular and atomic gas in the direction of the clouds. We find that the 3/4 ke V emission must be distributed throughout the Galactic disk. It is therefore linked to the structure of the cooler material of the ISM, and to the birth of stars.

  6. X-RAY SHADOWING EXPERIMENTS TOWARD INFRARED DARK CLOUDS

    International Nuclear Information System (INIS)

    Anderson, L. D.; Bania, T. M.; Snowden, S. L.

    2010-01-01

    We searched for X-ray shadowing toward two infrared dark clouds (IRDCs) using the MOS detectors on XMM-Newton to learn about the Galactic distribution of X-ray emitting plasma. IRDCs make ideal X-ray shadowing targets of 3/4 keV photons due to their high column densities, relatively large angular sizes, and known kinematic distances. Here we focus on two clouds near 30 0 Galactic longitude at distances of 2 and 5 kpc from the Sun. We derive the foreground and background column densities of molecular and atomic gas in the direction of the clouds. We find that the 3/4 keV emission must be distributed throughout the Galactic disk. It is therefore linked to the structure of the cooler material of the interstellar medium and to the birth of stars.

  7. Wake models developed during the Wind Shadow project

    Energy Technology Data Exchange (ETDEWEB)

    Larsen, S.; Ott, S.; Pena, A.; Berg, J.; Nielsen, M.; Rathmann, O.; Joergensen, H.

    2011-11-15

    The Wind Shadow project has developed and validated improved models for determining the wakes losses, and thereby the array efficiency of very large, closely packed wind farms. The rationale behind the project has been that the existing software has been covering these types of wind farms poorly, both with respect to the densely packed turbines and the large fetches needed to describe the collective shadow effects of one farm to the next. Further the project has developed the necessary software for the use of the models. Guidelines with recommendations for the use of the models are included in the model deliverables. The project has been carried out as a collaborative project between Risoe DTU, DONG, Vattenfall, DNV and VESTAS, and it has been financed by energinet.dk grant no. 10086. (Author)

  8. The Permanently Shadowed Regions of Dwarf Planet Ceres

    Science.gov (United States)

    Schorghofer, Norbert; Mazarico, Erwan; Platz, Thomas; Preusker, Frank; Schroeder, Stefan E.; Raymond, Carol A.; Russell, Christopher T.

    2016-01-01

    Ceres has only a small spin axis tilt (4 deg), and craters near its rotational poles can experience permanent shadow and trap volatiles, as is the case on Mercury and on Earth's Moon. Topography derived from stereo imaging by the Dawn spacecraft is used to calculate direct solar irradiance that defines the extent of the permanently shadowed regions (PSRs). In the northern polar region, PSRs cover approximately 1800 sq km or 0.13% of the hemisphere, and most of the PSRs are cold enough to trap water ice over geological time periods. Based on modeling of the water exosphere, water molecules seasonally reside around the winter pole and ultimately an estimated 0.14% of molecules get trapped. Even for the lowest estimates of the amount of available water, this predicts accumulation rates in excess of loss rates, and hence, there should be fresh ice deposits in the cold traps.

  9. Shadow Areas Robust Matching Among Image Sequence in Planetary Landing

    Science.gov (United States)

    Ruoyan, Wei; Xiaogang, Ruan; Naigong, Yu; Xiaoqing, Zhu; Jia, Lin

    2017-01-01

    In this paper, an approach for robust matching shadow areas in autonomous visual navigation and planetary landing is proposed. The approach begins with detecting shadow areas, which are extracted by Maximally Stable Extremal Regions (MSER). Then, an affine normalization algorithm is applied to normalize the areas. Thirdly, a descriptor called Multiple Angles-SIFT (MA-SIFT) that coming from SIFT is proposed, the descriptor can extract more features of an area. Finally, for eliminating the influence of outliers, a method of improved RANSAC based on Skinner Operation Condition is proposed to extract inliers. At last, series of experiments are conducted to test the performance of the approach this paper proposed, the results show that the approach can maintain the matching accuracy at a high level even the differences among the images are obvious with no attitude measurements supplied.

  10. AUTOMATIC SHADOW DETECTION IN AERIAL AND TERRESTRIAL IMAGES

    Directory of Open Access Journals (Sweden)

    Vander Luis de Souza Freitas

    Full Text Available Abstract: Shadows exist in almost all aerial and outdoor images, and they can be useful for estimating Sun position estimation or measuring object size. On the other hand, they represent a problem in processes such as object detection/recognition, image matching, etc., because they may be confused with dark objects and change the image radiometric properties. We address this problem on aerial and outdoor color images in this work. We use a filter to find low intensities as a first step. For outdoor color images, we analyze spectrum ratio properties to refine the detection, and the results are assessed with a dataset containing ground truth. For the aerial case we validate the detections depending of the hue component of pixels. This stage takes into account that, in deep shadows, most pixels have blue or violet wavelengths because of an atmospheric scattering effect.

  11. Medium Access Control for Opportunistic Concurrent Transmissions under Shadowing Channels.

    Science.gov (United States)

    Son, In Keun; Mao, Shiwen; Hur, Seung Min

    2009-01-01

    We study the problem of how to alleviate the exposed terminal effect in multi-hop wireless networks in the presence of log-normal shadowing channels. Assuming node location information, we propose an extension of the IEEE 802.11 MAC protocol that sched-ules concurrent transmissions in the presence of log-normal shadowing, thus mitigating the exposed terminal problem and improving network throughput and delay performance. We observe considerable improvements in throughput and delay achieved over the IEEE 802.11 MAC under various network topologies and channel conditions in ns-2 simulations, which justify the importance of considering channel randomness in MAC protocol design for multi-hop wireless networks.

  12. Preliminary neutron shielding calculations of the electronics in the EAST BES systems focusing on neutron induced displacement damage

    Energy Technology Data Exchange (ETDEWEB)

    Náfrádi, Gábor, E-mail: nafradi@reak.bme.hu [Institute of Nuclear Techniques (NTI), Budapest University of Technology and Economics (BME), H-1111 Budapest (Hungary); Kovácsik, Ákos, E-mail: kovacsik.akos@reak.bme.hu [Institute of Nuclear Techniques (NTI), Budapest University of Technology and Economics (BME), H-1111 Budapest (Hungary); Németh, József, E-mail: nemeth.jozsef@wigner.mta.hu [Institute for Particle and Nuclear Physics, Wigner Research Centre for Physics (Wigner RCP), Hungarian Academy of Sciences (HAS), POB 49, 1525 Budapest (Hungary); Pór, Gábor, E-mail: por@reak.bme.hu [Institute of Nuclear Techniques (NTI), Budapest University of Technology and Economics (BME), H-1111 Budapest (Hungary); Zoletnik, Sándor, E-mail: zoletnik.sandor@wigner.mta.hu [Institute for Particle and Nuclear Physics, Wigner Research Centre for Physics (Wigner RCP), Hungarian Academy of Sciences (HAS), POB 49, 1525 Budapest (Hungary)

    2016-11-15

    Monte Carlo N-Particle (MCNP) calculations were carried out to compare neutron shielding capabilities of three frequently used neutron shielding materials: polyethylene without neutron absorbers, polyethylene with boron absorbers and polyethylene with lithium absorbers, according to Non Ionizing Energy Loss (NIEL). The results of 1D shielding calculations showed that simple neutron moderating materials can provide sufficient and cheap shielding against 2.45 MeV and 14.1 MeV fusion neutrons, in terms of 1 MeV neutron equivalent flux, in silicon targets, which is the most commonly used material of electronic components. Based on these results a new shielding concept is proposed which can be taken into consideration where the reduction of displacement damage is the main goal and the free space available for shielding is limited. Based on this shielding concept detailed 3D calculations were carried out to describe the properties of the neutron shielding of the Beam Emission Spectroscopy (BES) system installed at the EAST tokamak.

  13. The use of nipple shields: A review

    Directory of Open Access Journals (Sweden)

    Selina Chow

    2016-11-01

    Full Text Available A nipple shield is a breastfeeding aid with a nipple-shaped shield that is positioned over the nipple and areola prior to nursing. Nipple shields are usually recommended to mothers with flat nipples or in cases in which there is a failure of the baby to effectively latch onto the breast within the first two days postpartum. The use of nipple shields is a controversial topic in the field of lactation. Its use has been an issue in the clinical literature since some older studies discovered reduced breast milk transfer when using nipple shields, while more recent studies reported successful breastfeeding outcomes. The purpose of this review was to examine the evidence and outcomes with nipple shield use. Methods: A literature search was conducted in Ovid MEDLINE, OLDMEDLINE, EMBASE Classic, EMBASE, Cochrane Central Register of Controlled Trials and CINAHL. The primary endpoint was any breastfeeding outcome following nipple shield use. Secondary endpoints included the reasons for nipple shield use and the average/median length of use. For the analysis, we examined the effect of nipple shield use on physiological responses, premature infants, mothers’ experiences, and health professionals’ experiences. Results: The literature search yielded 261 articles, 14 of which were included in this review. Of these 14 articles, three reported on physiological responses, two reported on premature infants, eight reported on mothers’ experiences, and one reported on health professionals’ experiences. Conclusion: Through examining the use of nipple shields, further insight is provided on the advantages and disadvantages of this practice, thus allowing clinicians and researchers to address improvements on areas that will benefit mothers and infants the most.

  14. Limiting Cash Circulation as a Means to Combat Shadow Economy

    Directory of Open Access Journals (Sweden)

    Galina S. Panova

    2014-01-01

    Full Text Available The article deals with actual problems of modern state and development prospects of cash circulation in Russia and abroad; the comparative analysis of monetization of the economy of Russia and foreign countries; quantitative parameters of aggregate money turnover, including the value of cash and non-cash spheres; the correlations of macroeconomic variables and indicators of cash circulation in Russia. Special attention is given by the authors to the limitations of cash payments and settlements in the fight against shadow economy. In particular, researched the level of shadow economy; the relationship between cash money circulation and shadow economy; the problems encountered by foreign states in imposing administrative limits on the amount of payments in cash; provides specific recommendations and outlines the required steps to introduce such restrictions in Russia. It is concluded that the limitation of the maximum size of payments in cash can lead to simultaneous reduce the underground economy because revenues derived from the hidden and informal economic activities can be translated in non-cash form. However, in the long run, when adopting legislative restrictions on the payment of funds by individuals on their own bank accounts or, for example, need to prove the lawful origin of money if you make them into a bank account to limit payments in cash will be the first step towards the goal of reducing shadow economy in Russia. In general, limiting the cash circulation - multi-factor task - that requires the solution of economic, political, social, administrative, psychological problems. The overall decrease in cash money (up to the optimum, economically justified level, it will lead to lower inflation rates, the level of corruption, will improve the investment climate and the liberalization of the credit market in our country.

  15. Corruption’s Reflection: Iraq’s Shadow Economy

    Science.gov (United States)

    2005-03-01

    prostitution, smuggling, bribery, political corruption , protection rackets; • Transfers—petty theft (e.g. pickpockets), larceny(burglary and armed robbery...importantly the impact that governance failures such as corruption have had on the development of a shadow economy have been extensively documented...after opening my shop a government inspector came, and I just had to pay him a bribe .[25] How widespread these types of government shakedowns were

  16. Shadow-mask evaporation through monolayer-modified nanostencils

    OpenAIRE

    Kolbel, M; Tjerkstra, RW; Brugger, J; van Rijn, CJM; Nijdam, W; Huskens, J; Reinhoudt, DN

    2002-01-01

    Gradual clogging of the apertures of nanostencils used as miniature shadow masks in metal evaporations can be reduced by coating the stencil with self-assembled monolayers (SAM). This is quantified by the dimensions (height and volume) of gold features obtained by nanostencil evaporation as measured by scanning electron microscopy (SEM) and atomic force microscopy (AFM). An increase in material deposition through the apertures by more than 100% can be achieved with SAM-coated stencils, which ...

  17. Corruption, shadow economy and income inequality: evidence from Asia

    OpenAIRE

    Kar, Saibal; Saha, Shrabani

    2012-01-01

    A number of recent studies for Latin America show that as the size of the informal economy grows, corruption is less harmful to inequality. We investigate if this relationship is equally compelling for developing countries in Asia where corruption, inequality and shadow economies are considerably large. We use Panel Least Square and Fixed Effects Models for Asia to find that both 'Corruption Perception Index' and 'ICRG' index are sensitive to a number of important macroeconomic variables. We ...

  18. Shadow Banking – Developments in Times of Financial Crisis

    Directory of Open Access Journals (Sweden)

    Bogdan Munteanu

    2016-01-01

    The paper considers the following entities and activities, without limitation to or completenessof viewpoints: finance companies, asset backed financial instruments, structured investments,financing vehicles, money market funds, asset managers, credit hedge funds and venture capital,providing characteristics of shadow banking and their economic functions relative to the classicbanking system, as they pose a systemic risk due to asymmetric information and gaps created inmatching liquidity tenures with duration, by using synthetic leverage finance.

  19. A shadowing lemma for quasi-hyperbolic strings of flows

    Science.gov (United States)

    Han, Bo; Wen, Xiao

    2018-01-01

    In this paper we prove a shadowing lemma for pseudo orbits made by quasi-hyperbolic strings. We allow singularities in question and hence, in particular, the quasi-hyperbolic strings are formulated by the rescaled linear Poincaré flow instead of the usual linear Poincaré flow. We also introduce the sectional Poincaré map and rescaled sectional Poincaré map for Lipschitz vector fields on Banach spaces in the article.

  20. A 1K shadow RAM for circumvention applications

    International Nuclear Information System (INIS)

    Murray, J.R.

    1991-01-01

    This paper reports that circumvention applications require a memory that retains data through radiation (total dose and transient) and loss of power. Various memory technologies have been reviewed and none, as yet, can meet, these requirements. However, if complementary metal oxide silicon (CMOS) and silicon nitride oxide silicon (SNOS) memories are combined in a shadow RAM (random access memory) configuration, the requirements can be fulfilled

  1. COMPUTER-AIDED DETECTION OF ACINAR SHADOWS IN CHEST RADIOGRAPHS

    Directory of Open Access Journals (Sweden)

    Tao Xu

    2013-05-01

    Full Text Available Despite the technological advances in medical diagnosis, accurate detection of infectious tuberculosis (TB still poses challenges due to complex image features and thus infectious TB continues to be a public health problem of global proportions. Currently, the detection of TB is mainly conducted visually by radiologists examining chest radiographs (CXRs. To reduce the backlog of CXR examination and provide more precise quantitative assessment, computer-aided detection (CAD systems for potential lung lesions have been increasingly adopted and commercialized for clinical practice. CADs work as supporting tools to alert radiologists on suspected features that could have easily been neglected. In this paper, an effective CAD system aimed for acinar shadow regions detection in CXRs is proposed. This system exploits textural and photometric features analysis techniques which include local binary pattern (LBP, grey level co-occurrence matrix (GLCM and histogram of oriented gradients (HOG to analyze target regions in CXRs. Classification of acinar shadows using Adaboost is then deployed to verify the performance of a combination of these techniques. Comparative study in different image databases shows that the proposed CAD system delivers consistent high accuracy in detecting acinar shadows.

  2. Interconnectedness between shadow and traditional banking systems in Europe

    Directory of Open Access Journals (Sweden)

    Popović Svetlana

    2017-01-01

    Full Text Available The financial crisis that emerged in the US quickly spread across Europe, causing a severe banking and sovereign debt crisis. That revealed the importance of short-term financing for traditional banks, which increased their exposure to the financial conditions on the interbank market. Financial innovations, especially the securitization process led to the growing importance of different institutions within the shadow banking system - which undergo a credit, liquidity and maturity transformation, without accessing the central bank liquidity or other forms of guarantees. The European banks had an active role in the US securitization process, but also securitized the products from the European market. The authors used the available data from the ECB statistics on shadow bank entities, broadly and narrowly defined, in order to analyze the various measures of interconnectedness between the shadow and traditional banking systems. The analysis showed that non-regulated financial institutions pose severe systemic risks, not just because of their size, but also due to the strong web of interconnectedness with the regulated banking sector.

  3. Self-shielding characteristics of aqueous self-cooled blankets for next generation fusion devices

    International Nuclear Information System (INIS)

    Pelloni, S.; Cheng, E.T.; Embrechts, M.J.

    1987-11-01

    The present study examines self-shielding characteristics for two aqueous self-cooled tritium producing driver blankets for next generation fusion devices. The aqueous Self-Cooled Blanket concept (ASCB) is a very simple blanket concept that relies on just structural material and coolant. Lithium compounds are dissolved in water to provide for tritium production. An ASCB driver blanket would provide a low technology and low temperature environment for blanket test modules in a next generation fusion reactor. The primary functions of such a blanket would be shielding, energy removal and tritium production. One driver blanket considered in this study concept relates to the one proposed for the Next European Torus (NET), while the second concept is indicative for the inboard shield design for the Engineering Test Reactor proposed by the USA (TIBER II/ETR). The driver blanket for NET is based on stainless steel for the structural material and aqueous solution, while the inboard shielding blanket for TIBER II/ETR is based on a tungsten/aqueous solution combination. The purpose of this study is to investigate self-shielding and heterogeneity effects in aqueous self-cooled blankets. It is found that no significant gains in tritium breeding can be achieved in the stainless steel blanket if spatial and energy self-shielding effects are considered, and the heterogeneity effects are also insignificant. The tungsten blanket shows a 5 percent increase in tritium production in the shielding blanket when energy and spatial self-shielding effects are accounted for. However, the tungsten blanket shows a drastic increase in the tritium breeding ratio due to heterogeneity effects. (author) 17 refs., 9 figs., 9 tabs

  4. Improved Metal-Polymeric Laminate Radiation Shielding, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — In this proposed Phase I program, a multifunctional lightweight radiation shield composite will be developed and fabricated. This structural radiation shielding will...

  5. Foam-Reinforced Polymer Matrix Composite Radiation Shields Project

    Data.gov (United States)

    National Aeronautics and Space Administration — New and innovative lightweight radiation shielding materials are needed to protect humans in future manned exploration vehicles. Radiation shielding materials are...

  6. Foam-Reinforced Polymer Matrix Composite Radiation Shields, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — New and innovative lightweight radiation shielding materials are needed to protect humans in future manned exploration vehicles. Radiation shielding materials are...

  7. Bootstrapping de-shadowing and self-calibration for scanning electron microscope photometric stereo

    International Nuclear Information System (INIS)

    Miyamoto, Atsushi; Chen, Deshan; Kaneko, Shun’ichi

    2014-01-01

    In this paper, we present a novel approach that addresses the blind reconstruction problem in scanning electron microscope (SEM) photometric stereo. Using only two observed images that suffer from shadowing effects, our method automatically calibrates the parameter and resolves shadowing errors for estimating an accurate three-dimensional (3D) shape and underlying shadowless images. We introduce a novel shadowing compensation model using image intensities for both cases of presence and absence of shadowing. With this model, the proposed de-shadowing algorithm iteratively compensates for image intensities and modifies the corresponding 3D surface. Besides de-shadowing, we introduce a practically useful self-calibration criterion by enforcing a good reconstruction. We show that incorrect parameters will engender significant distortions of 3D reconstructions in shadowed regions during the de-shadowing procedure. This motivated us to design the self-calibration criterion by utilizing shadowing to pursue the proper parameter that produces the best reconstruction with least distortions. As a result, we develop a bootstrapping approach for simultaneous de-shadowing and self-calibration in SEM photometric stereo. Extensive experiments on real image data demonstrate the effectiveness of our method. (paper)

  8. SOCIO-ECONOMIC NATURE OF SHADOW ECONOMY AND CAUSES OF ITS DEVELOPMENT IN ENTREPRENEURSHIP

    Directory of Open Access Journals (Sweden)

    I. Mazur

    2017-01-01

    Full Text Available The socio-economic nature of the shadow economy is revealed. The shadow economy has both positive and negative signs for the society; the possibility for the population to survive in conditions of economic crisis, reducing transaction costs authors refer to positive signs, and the destructive economic development to negative. The common (prohibitions and restrictions and partial (high tax burden and inefficient system of its administration; numerous bureaucratic procedures; mistrust to the government institutions and the judiciary; corruption in all levels of the governance, etc. causes of the shadow economy in entrepreneurship are disclosed. It is argued that the shadow economy is neither a sector nor a certain part of the legal economy, it can be in any sector of the legal economy closely interlaced with it, and therefore its limits cannot be clearly identified (determine in the formal economy. The shadow economy is not possible to determine especially in the information society. The categories of the shadow economy and its structuring are suggested. It has been researched the historical roots of the shadow economy spread in entrepreneurship, and lie in the shadow of public-private partnership which carries interests of "civil servant-entrepreneurs" and allows to manage state resources and control market. Therefore, the shadow policy creates favorable conditions for the entrepreneurs to work in the shadow. At the same time, access to the shadow entails stricter regulation by the state. It is proved that corruption is a part of the shadow economy, not an independent phenomenon, so they should be research comprehensively and systematically. Instead of overcoming the shadow economy and its component - corruption has been suggested to establish favorable business environment for their unfavorable existence, that is to carry out deshadowing of the economy.

  9. Development of neutron shielding material for cask

    International Nuclear Information System (INIS)

    Najima, K.; Ohta, H.; Ishihara, N.; Matsuoka, T.; Kuri, S.; Ohsono, K.; Hode, S.

    2001-01-01

    Since 1980's Mitsubishi Heavy Industries, Ltd (MHI) has established transport and storage cask design 'MSF series' which makes higher payload and reliability for long term storage. MSF series transport and storage cask uses new-developed neutron shielding material. This neutron shielding material has been developed for improving durability under high condition for long term. Since epoxy resin contains a lot of hydrogen and is comparatively resistant to heat, many casks employ epoxy base neutron shielding material. However, if the epoxy base neutron shielding material is used under high temperature condition for a long time, the material deteriorates and the moisture contained in it is released. The loss of moisture is in the range of several percents under more than 150 C. For this reason, our purpose was to develop a high durability epoxy base neutron shielding material which has the same self-fire-extinction property, high hydrogen content and so on as conventional. According to the long-time heating test, the weight loss of this new neutron shielding material after 5000 hours heating has been lower than 0.04% at 150 C and 0.35% at 170 C. A thermal test was also performed: a specimen of neutron shielding material covered with stainless steel was inserted in a furnace under condition of 800 C temperature for 30 minutes then was left to cool down in ambient conditions. The external view of the test piece shows that only a thin layer was carbonized

  10. Thermal testing of solid neutron shielding materials

    International Nuclear Information System (INIS)

    Boonstra, R.H.

    1992-09-01

    Two legal-weight truck casks the GA-4 and GA-9, will carry four PWR and nine BWR spent fuel assemblies, respectively. Each cask has a solid neutron shielding material separating the steel body and the outer steel skin. In the thermal accident specified by NRC regulations in 10CFR Part 71, the cask is subjected to an 800 degree C environment for 30 minutes. The neutron shield need not perform any shielding function during or after the thermal accident, but its behavior must not compromise the ability of the cask to contain the radioactive contents. In May-June 1989 the first series of full-scale thermal tests was performed on three shielding materials: Bisco Products NS-4-FR, and Reactor Experiments RX-201 and RX-207. The tests are described in Thermal Testing of Solid Neutron Shielding Materials, GA-AL 9897, R. H. Boonstra, General Atomics (1990), and demonstrated the acceptability of these materials in a thermal accident. Subsequent design changes to the cask rendered these materials unattractive in terms of weight or adequate service temperature margin. For the second test series, a material specification was developed for a polypropylene based neutron shield with a softening point of at least 280 degree F. The neutron shield materials tested were boronated (0.8--4.5%) polymers (polypropylene, HDPE, NS-4). The Envirotech and Bisco materials are not polypropylene, but were tested as potential backup materials in the event that a satisfactory polypropylene could not be found

  11. Shielding concerns at a spallation source

    International Nuclear Information System (INIS)

    Russell, G.J.; Robinson, H.; Legate, G.L.; Woods, R.

    1989-01-01

    Neutrons produced by 800-MeV proton reactions at the Los Alamos Neutron Scattering Center spallation neutron source cause a variety of challenging shielding problems. We identify several characteristics distinctly different from reactor shielding and compute the dose attenuation through an infinite slab/shield composed of iron (100 cm) and borated polyethylene (15 cm). Our calculations show that (for an incident spallation spectrum characteristic of neutrons leaking from a tungsten target at 90/degree/) the dose through the shield is a complex mixture of neutrons and gamma rays. High-energy (> 20 MeV) neutron production from the target is ≅5% of the total, yet causes ≅68% of the dose at the shield surface. Primary low-energy (< 20 MeV) neutrons from the target contribute negligibly (≅0.5%) to the dose at the shield surface yet cause gamma rays, which contribute ≅31% to the total dose at the shield surface. Low-energy neutrons from spallation reactions behave similarly to neutrons with a fission spectrum distribution. 6 refs., 8 figs., 1 tab

  12. Integrated Solar Concentrator and Shielded Radiator

    Science.gov (United States)

    Clark, David Larry

    2010-01-01

    A shielded radiator is integrated within a solar concentrator for applications that require protection from high ambient temperatures with little convective heat transfer. This innovation uses a reflective surface to deflect ambient thermal radiation, shielding the radiator. The interior of the shield is also reflective to provide a view factor to deep space. A key feature of the shield is the parabolic shape that focuses incoming solar radiation to a line above the radiator along the length of the trough. This keeps the solar energy from adding to the radiator load. By placing solar cells along this focal line, the concentration of solar energy reduces the number and mass of required cells. By shielding the radiator, the effective reject temperature is much lower, allowing lower radiator temperatures. This is particularly important for lower-temperature processes, like habitat heat rejection and fuel cell operations where a high radiator temperature is not feasible. Adding the solar cells in the focal line uses the concentrating effect of the shield to advantage to accomplish two processes with a single device. This shield can be a deployable, lightweight Mylar structure for compact transport.

  13. The shadow of a doubt ? Evidence for perceptuo-motor linkage during auditory and audiovisual close shadowing

    Directory of Open Access Journals (Sweden)

    Lucie eScarbel

    2014-06-01

    Full Text Available One classical argument in favor of a functional role of the motor system in speech perception comes from the close shadowing task in which a subject has to identify and to repeat as quickly as possible an auditory speech stimulus. The fact that close shadowing can occur very rapidly and much faster than manual identification of the speech target is taken to suggest that perceptually-induced speech representations are already shaped in a motor-compatible format. Another argument is provided by audiovisual interactions often interpreted as referring to a multisensory-motor framework. In this study, we attempted to combine these two paradigms by testing whether the visual modality could speed motor response in a close-shadowing task. To this aim, both oral and manual responses were evaluated during the perception of auditory and audio-visual speech stimuli, clear or embedded in white noise. Overall, oral responses were faster than manual ones, but it also appeared that they were less accurate in noise, which suggests that motor representations evoked by the speech input could be rough at a first processing stage. In the presence of acoustic noise, the audiovisual modality led to both faster and more accurate responses than the auditory modality. No interaction was however observed between modality and response. Altogether, these results are interpreted within a two-stage sensory-motor framework, in which the auditory and visual streams are integrated together and with internally generated motor representations before a final decision may be available.

  14. Simple evaluation of CT findings in the paranasal sinuses for chronic sinusitis

    Energy Technology Data Exchange (ETDEWEB)

    Miyazaki, Makoto [Saiseikai Shiga Hospital, Ritto (Japan); Dejima, Kenji; Hama, Takemitsu; Ishizaka, Shigeyasu; Yasuda, Shigenobu; Fukushima, Kazuto; Murakami, Yasushi; Hisa, Yasuo

    2000-02-01

    The CT scores and scoring for improvement based on them, which we proposed previously, is a simple and highly reproducible method of evaluation of sinus units before and after an operation for chronic sinusitis. We compared this evaluation method with the results of quantitative assay and showed its advantages and disadvantages. The subjects were 258 sinuses in patients who underwent endonasal sinus surgery (ESS) in the department of otolaryngology, Kyoto Prefectural University of Medicine Hospital from April 1996 to April 1997. The subjects were evaluated according to the following 4 grades negligible shadow in the paranasal sinus CT scored 0, less than 50% shadow scored 1, more than 50% of shadow scored 2, and mostly filled with shadow scored 3. Furthermore, the preoperative and postoperative CT scores were compared and the rate of improvement was rated in the following 3 grades: score 0 for unchanged or aggravated subjects, score 1 for subjects showing improved CT score by 1 grade, and score 2 for those showing improved CT score by 2 grades or a postoperative CT score of 0. Quantitative image analysis was input into a personal computer and the ratio occupied by the shadow was calculated, as the shadow ratio. While some discrepancies were seen in parts in the comparison of the quantitative image analysis and CT scores as the former captures minute shadows, a positive correlation was obtained overall. Attention is needed to accurately evaluate small paranasal sinuses such as the frontal sinus, and small amounts of shadow, which are areas where errors may occur. A satisfactory correlation was obtained between the score for the improvement rate and the difference in the shadow ratios before and after surgery. The CT scores and the scores for the improvement rate showed no difference from the results of other evaluation methods reported in the past, and evaluation of similar precision was possible. It was thought that this simple evaluation method of CT findings in

  15. PWR upper/lower internals shield

    Energy Technology Data Exchange (ETDEWEB)

    Homyk, W.A. [Indian Point Station, Buchanan, NY (United States)

    1995-03-01

    During refueling of a nuclear power plant, the reactor upper internals must be removed from the reactor vessel to permit transfer of the fuel. The upper internals are stored in the flooded reactor cavity. Refueling personnel working in containment at a number of nuclear stations typically receive radiation exposure from a portion of the highly contaminated upper intervals package which extends above the normal water level of the refueling pool. This same issue exists with reactor lower internals withdrawn for inservice inspection activities. One solution to this problem is to provide adequate shielding of the unimmersed portion. The use of lead sheets or blankets for shielding of the protruding components would be time consuming and require more effort for installation since the shielding mass would need to be transported to a support structure over the refueling pool. A preferable approach is to use the existing shielding mass of the refueling pool water. A method of shielding was devised which would use a vacuum pump to draw refueling pool water into an inverted canister suspended over the upper internals to provide shielding from the normally exposed components. During the Spring 1993 refueling of Indian Point 2 (IP2), a prototype shield device was demonstrated. This shield consists of a cylindrical tank open at the bottom that is suspended over the refueling pool with I-beams. The lower lip of the tank is two feet below normal pool level. After installation, the air width of the natural shielding provided by the existing pool water. This paper describes the design, development, testing and demonstration of the prototype device.

  16. Response dependence of an albedo-neutron dosemeter on the properties of shielding

    International Nuclear Information System (INIS)

    Doerschel, B.; Herforth, L.; Schuricht, V.

    1976-07-01

    The ratio of the response of an albedo-neutron dosemeter to the biological neutron dose has been calculated for pile and 14-MeV neutrons in dependence on the thickness of several shielding materials, such as iron, water, and concrete. The results obtained show great differences of this ratio for pile and 14-MeV neutrons. Therefore, errors in estimating the biological neutron dose due to changes in the primary neutron energy spectra beyond shields limit the application of simple albedo-neutron dosemeters

  17. Preparation of non-spherical particles by shell-shield etching for near-field nanopatterning

    International Nuclear Information System (INIS)

    Ye, Jian; Liesbet, Lagae

    2014-01-01

    The shape of polymer particles plays an important role in determining their function. In this paper, we describe a simple and unconventional method called shell-shield etching (SSE) that allows us to prepare freestanding submicrometer- or micrometer-sized polymer particles with various shapes. By precisely varying the time of ultraviolet ozone treatment under the partial shielding effect of the silica shell, we controllably reshape polymer spheres into symmetry-reduced polymer peaches, mushrooms, bowls, and plates. Finite difference time domain simulations indicate that the non-spherical particles obtained from the SSE method might have potential for near-field nanopatterning applications. (papers)

  18. Designing an Optimal Lightning Protection Scheme for Substations Using Shielding Wires

    Directory of Open Access Journals (Sweden)

    A. Khodadadi

    2017-06-01

    Full Text Available An optimal lightning protection scheme for a substation using shielding wires is investigated in this paper through computer software analysis. An economic approach is utilized by choosing a reasonable trade-off between protection, the number of shielding wires and the heights of them from the ground. This study is initially applied to a simple two-wire system and then extended to a sample substation. The solution for each problem is executed in MATLAB and 3-D realization is shown.

  19. Seismic proof test of shielding block walls

    International Nuclear Information System (INIS)

    Ohte, Yukio; Watanabe, Takahide; Watanabe, Hiroyuki; Maruyama, Kazuhide

    1989-01-01

    Most of the shielding block walls used for building nuclear facilities are built by dry process. When a nuclear facility is designed, seismic waves specific at each site are set as input seismic motions and they are adopted in the design. Therefore, it is necessary to assure safety of the shielding block walls for earthquake by performing anti-seismic experiments under the conditions at each site. In order to establish the normal form that can be applied to various seismic conditions in various areas, Shimizu Corp. made an actual-size test samples for the shielding block wall and confirmed the safety for earthquake and validity of normalization. (author)

  20. A source of illumination for low-noise ‘Violin-Mode’ shadow sensors, intended for use in interferometric gravitational wave detectors

    International Nuclear Information System (INIS)

    Lockerbie, N A; Tokmakov, K V; Strain, K A

    2014-01-01

    A low-noise source of illumination is described for shadow sensors having a displacement sensitivity of (69  ±  13) picometres (rms)/√Hz, at 500 Hz, over a measuring span of ±0.1 mm. These sensors were designed to detect ‘Violin-Mode’ resonances in the suspension fibres of the test-masses/mirrors for the Advanced LIGO (Laser Interferometer Gravitational wave Observatory) gravitational wave detectors. The source of illumination (emitter) described here used a single column of 8 × miniature near infrared LEDs (λ = 890 nm). These emitters cast the shadows of 400 μm diameter fused silica suspension fibres onto their complementary shadow-displacement detectors, located at a distance of 74 fibre diameters (29.6 mm) behind the axes of the fibres themselves. Violin-Mode vibrations of each fibre were sensed as differential ac photocurrents in the corresponding ‘split-photodiode’ detector. This paper describes the design, construction, noise analysis, and measures that were taken in the conception of the emitters, in order to produce high-contrast shadows at such distant detectors. In this way it proved possible to obtain, simultaneously, a very high transfer sensitivity to Violin-Mode vibration of the fibres, and a very low level of detection noise—close to the fundamental shot noise limit—whilst remaining within the constraints of this simple design of emitter. The shadow detector is described in an accompanying paper. (paper)

  1. An image-space parallel convolution filtering algorithm based on shadow map

    Science.gov (United States)

    Li, Hua; Yang, Huamin; Zhao, Jianping

    2017-07-01

    Shadow mapping is commonly used in real-time rendering. In this paper, we presented an accurate and efficient method of soft shadows generation from planar area lights. First this method generated a depth map from light's view, and analyzed the depth-discontinuities areas as well as shadow boundaries. Then these areas were described as binary values in the texture map called binary light-visibility map, and a parallel convolution filtering algorithm based on GPU was enforced to smooth out the boundaries with a box filter. Experiments show that our algorithm is an effective shadow map based method that produces perceptually accurate soft shadows in real time with more details of shadow boundaries compared with the previous works.

  2. Particle Tracing Modeling with SHIELDS

    Science.gov (United States)

    Woodroffe, J. R.; Brito, T. V.; Jordanova, V. K.

    2017-12-01

    The near-Earth inner magnetosphere, where most of the nation's civilian and military space assets operate, is an extremely hazardous region of the space environment which poses major risks to our space infrastructure. Failure of satellite subsystems or even total failure of a spacecraft can arise for a variety of reasons, some of which are related to the space environment: space weather events like single-event-upsets and deep dielectric charging caused by high energy particles, or surface charging caused by low to medium energy particles; other space hazards are collisions with natural or man-made space debris, or intentional hostile acts. A recently funded project through the Los Alamos National Laboratory (LANL) Directed Research and Development (LDRD) program aims at developing a new capability to understand, model, and predict Space Hazards Induced near Earth by Large Dynamic Storms, the SHIELDS framework. The project goals are to understand the dynamics of the surface charging environment (SCE), the hot (keV) electrons on both macro- and microscale. These challenging problems are addressed using a team of world-class experts and state-of-the-art physics-based models and computational facilities. We present first results of a coupled BATS-R-US/RAM-SCB/Particle Tracing Model to evaluate particle fluxes in the inner magnetosphere. We demonstrate that this setup is capable of capturing the earthward particle acceleration process resulting from dipolarization events in the tail region of the magnetosphere.

  3. REPOSITORY RADIATION SHIELDING DESIGN GUIDE

    International Nuclear Information System (INIS)

    M. Haas; E.M. Fortsch

    1997-01-01

    The scope of this document includes radiation safety considerations used in the design of facilities for the Yucca Mountain Site Characterization Project (YMP). The purpose of the Repository Radiation Shielding Design Guide is to document the approach used in the radiological design of the Mined Geologic Disposal System (MGDS) surface and subsurface facilities for the protection of workers, the public, and the environment. This document is intended to ensure that a common methodology is used by all groups that may be involved with Radiological Design. This document will also assist in ensuring the long term survivability of the information basis used for radiological safety design and will assist in satisfying the documentation requirements of the licensing body, the Nuclear Regulatory Commission (NRC). This design guide provides referenceable information that is current and maintained under the YMP Quality Assurance (QA) Program. Furthermore, this approach is consistent with maintaining continuity in spite of a changing design environment. This approach also serves to ensure common inter-disciplinary interpretation and application of data

  4. REPOSITORY RADIATION SHIELDING DESIGN GUIDE

    Energy Technology Data Exchange (ETDEWEB)

    M. Haas; E.M. Fortsch

    1997-09-12

    The scope of this document includes radiation safety considerations used in the design of facilities for the Yucca Mountain Site Characterization Project (YMP). The purpose of the Repository Radiation Shielding Design Guide is to document the approach used in the radiological design of the Mined Geologic Disposal System (MGDS) surface and subsurface facilities for the protection of workers, the public, and the environment. This document is intended to ensure that a common methodology is used by all groups that may be involved with Radiological Design. This document will also assist in ensuring the long term survivability of the information basis used for radiological safety design and will assist in satisfying the documentation requirements of the licensing body, the Nuclear Regulatory Commission (NRC). This design guide provides referenceable information that is current and maintained under the YMP Quality Assurance (QA) Program. Furthermore, this approach is consistent with maintaining continuity in spite of a changing design environment. This approach also serves to ensure common inter-disciplinary interpretation and application of data.

  5. Shielding Calculations for PUSPATI TRIGA Reactor (RTP) Fuel Transfer Cask with Micro shield

    International Nuclear Information System (INIS)

    Nurhayati Ramli; Ahmad Nabil Abdul Rahim; Ariff Shah Ismail

    2011-01-01

    The shielding calculations for RTP fuel transfer cask was performed by using computer code Micro shield 7.02. Micro shield is a computer code designed to provide a model to be used for shielding calculations. The results of the calculations can be obtained fast but the code is not suitable for complex geometries with a shielding composed of more than one material. Nevertheless, the program is sufficient for As Low As Reasonable Achievable (ALARA) optimization calculations. In this calculation, a geometry based on the conceptual design of RTP fuel transfer cask was modeled. Shielding material used in the calculations were lead (Pb) and stainless steel 304 (SS304). The results obtained from these calculations are discussed in this paper. (author)

  6. ANALYZING SPECTRAL CHARACTERISTICS OF SHADOW AREA FROM ADS-40 HIGH RADIOMETRIC RESOLUTION AERIAL IMAGES

    Directory of Open Access Journals (Sweden)

    Y.-T. Hsieh

    2016-06-01

    Full Text Available The shadows in optical remote sensing images are regarded as image nuisances in numerous applications. The classification and interpretation of shadow area in a remote sensing image are a challenge, because of the reduction or total loss of spectral information in those areas. In recent years, airborne multispectral aerial image devices have been developed 12-bit or higher radiometric resolution data, including Leica ADS-40, Intergraph DMC. The increased radiometric resolution of digital imagery provides more radiometric details of potential use in classification or interpretation of land cover of shadow areas. Therefore, the objectives of this study are to analyze the spectral properties of the land cover in the shadow areas by ADS-40 high radiometric resolution aerial images, and to investigate the spectral and vegetation index differences between the various shadow and non-shadow land covers. According to research findings of spectral analysis of ADS-40 image: (i The DN values in shadow area are much lower than in nonshadow area; (ii DN values received from shadowed areas that will also be affected by different land cover, and it shows the possibility of land cover property retrieval as in nonshadow area; (iii The DN values received from shadowed regions decrease in the visible band from short to long wavelengths due to scattering; (iv The shadow area NIR of vegetation category also shows a strong reflection; (v Generally, vegetation indexes (NDVI still have utility to classify the vegetation and non-vegetation in shadow area. The spectral data of high radiometric resolution images (ADS-40 is potential for the extract land cover information of shadow areas.

  7. The impact of economic globalization on the shadow economy in Egypt

    OpenAIRE

    Farzanegan, Mohammad Reza; Hassan, Mai

    2017-01-01

    This study examines the economic globalization and the shadow economy nexus in Egypt. Using time series data from 1976 to 2013, the impulse response analysis shows that the response of the shadow economy in Egypt to positive shocks in economic globalization is negative and statistically significant for the first three years following the shock. This finding is obtained by controlling for several intermediary channels in globalization-shadow economy nexus such as education, government spending...

  8. Experimental test of the shadowing effect in Smith-Purcell radiation

    International Nuclear Information System (INIS)

    Naumenko, G.A.; Potylitsyn, A.P.; Popov, Yu.A.; Shevelev, M.V

    2011-01-01

    The observation of a shadowing effect of a relativistic electron Coulomb field for the Smith-Purcell radiation generation is presented in this paper. For this purpose the surface current from the closest surface of grating element to the electron beam was measured for a downstream one shadowed by upstream element. The experimental results showed that shadowing effect for Smith-Purcell radiation depends on grating geometry.

  9. Shielding properties of fibre cement wallboard.

    Science.gov (United States)

    Thiele, D L; Godwin, G A; Coakley, K S

    1998-09-01

    Transmission data for a fibre cement wallboard (villaboard) are determined for use in diagnostic shielding designs. Villaboard is found to be more attenuating than plasterboard e.g. 9 mm of villaboard is equivalent to 16 mm of plasterboard.

  10. Thermal testing of solid neutron shielding materials

    International Nuclear Information System (INIS)

    Boonstra, R.H.

    1990-03-01

    The GA-4 and GA-9 spent fuel shipping casks employ a solid neutron shielding material. During a hypothetical thermal accident, any combustion of the neutron shield must not compromise the ability of the cask to contain the radioactive contents. A two-phase thermal testing program was carried out to assist in selecting satisfactory shielding materials. In the first phase, small-scale screening tests were performed on nine candidate materials using ASTM procedures. From these initial results, three of the nine candidates were chosen for inclusion in the second phase of testing, These materials were Bisco Products NS-4-FR, Reactor Experiments 201-1, and Reactor Experiments 207. In the second phase, each selected material was fabricated into a test article which simulated a full-scale of neutron shield from the cask. The test article was heated in an environmental prescribed by NRC regulations. Results of this second testing phase showed that all three materials are thermally acceptable

  11. Multifunctional BHL Radiation Shield, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Advances in radiation shielding technology remain an important challenge for NASA in order to protect their astronauts, particularly as NASA grows closer to manned...

  12. Thermal testing of solid neutron shielding materials

    International Nuclear Information System (INIS)

    Boonstra, R.N.

    1990-01-01

    The GA-4 and GA-9 spent fuel shipping casks employ a solid neutron shielding material. During a hypothetical thermal accident, any combustion of the neutron shield must not compromise the ability of the cask to contain the radioactive contents. A two-phase thermal testing program was carried out to assist in selecting satisfactory shielding materials. In the first phase, small-scale screening tests were performed on nine candidate materials using ASTM procedures. From these initial results, three of the nine candidates were chosen for inclusion in the second phase of testing. These materials were Bisco Products NS-4-FR, Reactor Experiments 201-1, and Reactor Experiments 207. In the second phase, each selected material was fabricated into a test article which simulated a full-scale section of neutron shield from the cask. The test article was heated in an environment prescribed by NRC regulations. Results of this second testing phase show that all three materials are thermally acceptable

  13. Long Duration Space Shelter Shielding, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Physical Sciences Inc. (PSI) has developed fiber reinforced ceramic composites for radiation shielding that can be used for external walls in long duration manned...

  14. Radiation shielding method for pipes, etc

    International Nuclear Information System (INIS)

    Nagao, Tetsuya; Takahashi, Shuichi.

    1988-01-01

    Purpose: To constitute shielding walls of a dense structure around pipes and enable to reduce the wall thickness thereof upon periodical inspection, etc. for nuclear power plants. Constitution: For those portions of pipes requring shieldings, cylindrical vessels surrounding the portions are disposed and connected to a mercury supply system, a mercury discharge system and a freezing system for solidifying mercury. After charging mercury in a tank by way of a supply hose to the cylindrical vessels, the temperature of the mercury is lowered below the freezing point thereof to solidify the mercury while circulating cooling medium, to thereby form dense cylindrical radioactive-ray shielding walls. The specific gravity of mercury is greater than that of lead and, accordingly, the thickness of the shielding walls can be reduced as compared with the conventional wall thickness of the entire laminates. (Takahashi, M.)

  15. Long Duration Space Shelter Shielding, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — Physical Sciences Inc. (PSI) has developed a ceramic composite material system that is more effective for shielding both GCR and SPE than aluminum. The composite...

  16. Shielding design for better plant availability

    International Nuclear Information System (INIS)

    Biro, G.G.

    1975-01-01

    Design methods are described for providing a shield system for nuclear power plants that will facilitate maintenance and inspection, increase overall plant availability, and ensure that man-rem exposures are as low as practicable

  17. Radiation shielding structure for concrete structure

    International Nuclear Information System (INIS)

    Oya, Hiroshi

    1998-01-01

    Crack inducing members for inducing cracks in a predetermined manner are buried in a concrete structure. Namely, a crack-inducing member comprises integrally a shielding plate and extended plates situated at the center of a wall and inducing plates vertically disposed to the boundary portion between them with the inducing plates being disposed each in a direction perforating the wall. There are disposed integrally a pair of the inducing plate spaced at a predetermined horizontal distance on both sides of the shielding plate so as to form a substantially crank-shaped cross section and extended plates formed in the extending direction of the shielding plate, and the inducing plates are disposed each in a direction perforating the wall. Then, cracks generated when stresses are exerted can be controlled, and generation of cracks passing through the concrete structure can be prevented reliably. The reliability of a radiation shielding effect can be enhanced remarkably. (N.H.)

  18. Technical specifications for the bulk shielding reactor

    International Nuclear Information System (INIS)

    1986-05-01

    This report provides information concerning the technical specifications for the Bulk Shielding Reactor. Areas covered include: safety limits and limiting safety settings; limiting conditions for operation; surveillance requirements; design features; administrative controls; and monitoring of airborne effluents. 10 refs

  19. Passive Shielding for Low Frequency Magnetic Films

    National Research Council Canada - National Science Library

    Damaskos, Nickander

    1997-01-01

    Report developed under SBIR Contract. An approach to low frequency shielding is shown with application to suppression of electromagnetic fields emanating from rail gun barrels and power cable busses. Damaskos, Inc...

  20. Method to produce a neutron shielding

    International Nuclear Information System (INIS)

    Merkle, H.J.

    1978-01-01

    The neutron shielding for armoured vehicles consists of preshaped plastic plates which are coated on the armoured vehicle walls by conversion of the thermoplast. Suitable plastics or thermoplasts are PVC, PVC acetate, or mixtures of these, into which more than 50% B, B 4 C, or BN is embedded. The colour of the shielding may be determined by the choice of the neutron absorber, e.g. a white colour for BN. The plates are produced using an extruder or calender. (DG) [de

  1. Shield structure for a nuclear reactor

    International Nuclear Information System (INIS)

    Rouse, C.A.; Simnad, M.T.

    1979-01-01

    An improved nuclear reactor shield structure is described for use where there are significant amounts of fast neutron flux above an energy level of approximately 70 keV. The shield includes structural supports and neutron moderator and absorber systems. A portion at least of the neutron moderator material is magnesium oxide either alone or in combination with other moderator materials such as graphite and iron. (U.K.)

  2. ANALISIS KESELAMATAN TERMOHIDROLIK BULK SHIELDING REAKTOR KARTINI

    Directory of Open Access Journals (Sweden)

    Azizul Khakim

    2015-10-01

    Full Text Available ABSTRAK ANALISIS KESELAMATAN TERMOHIDROLIK BULK SHIELDING REAKTOR KARTINI. Bulk shielding merupakan fasilitas yang terintegrasi dengan reaktor Kartini yang berfungsi sebagai penyimpanan sementara bahan bakar bekas. Fasilitas ini merupakan fasilitas yang termasuk dalam struktur, sistem dan komponen (SSK yang penting bagi keselamatan. Salah satu fungsi keselamatan dari sistem penanganan dan penyimpanan bahan bakar adalah mencegah kecelakaan kekritisan yang tak terkendali dan membatasi naiknya temperatur bahan bakar. Analisis keselamatan paling kurang harus mencakup analisis keselamatan dari sisi neutronik dan termo hidrolik Bulk shielding. Analisis termo hidrolik ditujukan untuk memastikan perpindahan panas dan proses pendinginan bahan bakar bekas berjalan baik dan tidak terjadi akumulasi panas yang mengancam integritas bahan bakar. Code tervalidasi PARET/ANL digunakan untuk analisis pendinginan dengan mode konveksi alam. Hasil perhitungan menunjukkan bahwa mode pendinginan konvekasi alam cukup memadai dalam mendinginkan panas sisa tanpa mengakibatkan kenaikan temperatur bahan bakar yang signifikan. Kata kunci: Bulk shielding, bahan bakar bekas, konveksi alam, PARET.   ABSTRACT THERMAL HYDRAULIC SAFETY ANALYSIS OF BULK SHIELDING KARTINI REACTOR. Bulk shielding is an integrated facility to Kartini reactor which is used for temporary spent fuels storage. The facility is one of the structures, systems and components (SSCs important to safety. Among the safety functions of fuel handling and storage are to prevent any uncontrolable criticality accidents and to limit the fuel temperature increase. Safety analyses should, at least, cover neutronic and thermal hydraulic calculations of the bulk shielding. Thermal hydraulic analyses were intended to ensure that heat removal and the process of the spent fuels cooling takes place adequately and no heat accumulation that challenges the fuel integrity. Validated code, PARET/ANL was used for analysing the

  3. Radiation shielding of the main injector

    International Nuclear Information System (INIS)

    Bhat, C.M.; Martin, P.S.

    1995-05-01

    The radiation shielding in the Fermilab Main Injector (FMI) complex has been carried out by adopting a number of prescribed stringent guidelines established by a previous safety analysis. Determination of the required amount of radiation shielding at various locations of the FMI has been done using Monte Carlo computations. A three dimensional ray tracing code as well as a code based upon empirical observations have been employed in certain cases

  4. The Absolute Shielding Constants of Heavy Nuclei: Resolving the Enigma of the (119)Sn Absolute Shielding.

    Science.gov (United States)

    Malkin, Elena; Komorovsky, Stanislav; Repisky, Michal; Demissie, Taye B; Ruud, Kenneth

    2013-02-07

    We demonstrate that the apparent disagreement between experimental determinations and four-component relativistic calculations of the absolute shielding constants of heavy nuclei is due to the breakdown of the commonly assumed relation between the electronic contribution to the nuclear spin-rotation constants and the paramagnetic contribution to the NMR shielding constants. We demonstrate that this breakdown has significant consequences for the absolute shielding constant of (119)Sn, leading to errors of about 1000 ppm. As a consequence, we expect that many absolute shielding constants of heavy nuclei will be in need of revision.

  5. Single-Image Shadow Removal Using 3D Intensity Surface Modeling.

    Science.gov (United States)

    He, Kai; Zhen, Rui; Yan, Jiaxing; Ge, Yunfeng

    2017-09-11

    Shadow removal from a single image is a challenging problem, whose solution is proposed in this study using 3D intensity surface modeling. Due to the high-order textural content in the original images, a direct modeling of the intensity surface of shadow image is difficult. In this study, image decomposition technology is used as an edge-preserving filter to remove the textural detail while keeping the local-smoothness pattern of image intensity surface. Using 3D modeling, a proper intensity surface of illumination in shadow region can be obtained based on that corresponding to the same texture in the non-shadow one. Thus, the intensity surface of shadow region can be compensated with a respective shadow-removal. Experimental results demonstrate the effectiveness of the proposed approach in the aspect of single-image shadow removal. In contrast to the alternative methods, it is not limited by additional assumptions or conditions; moreover, it can deal with the non-uniform and curved surface shadows, and is applicable to the shadow regions consisting of different types of textures.

  6. A hardware architecture for real-time shadow removal in high-contrast video

    Science.gov (United States)

    Verdugo, Pablo; Pezoa, Jorge E.; Figueroa, Miguel

    2017-09-01

    Broadcasting an outdoor sports event at daytime is a challenging task due to the high contrast that exists between areas in the shadow and light conditions within the same scene. Commercial cameras typically do not handle the high dynamic range of such scenes in a proper manner, resulting in broadcast streams with very little shadow detail. We propose a hardware architecture for real-time shadow removal in high-resolution video, which reduces the shadow effect and simultaneously improves shadow details. The algorithm operates only on the shadow portions of each video frame, thus improving the results and producing more realistic images than algorithms that operate on the entire frame, such as simplified Retinex and histogram shifting. The architecture receives an input in the RGB color space, transforms it into the YIQ space, and uses color information from both spaces to produce a mask of the shadow areas present in the image. The mask is then filtered using a connected components algorithm to eliminate false positives and negatives. The hardware uses pixel information at the edges of the mask to estimate the illumination ratio between light and shadow in the image, which is then used to correct the shadow area. Our prototype implementation simultaneously processes up to 7 video streams of 1920×1080 pixels at 60 frames per second on a Xilinx Kintex-7 XC7K325T FPGA.

  7. Planetary-like spirals caused by moving shadows in transition discs

    Science.gov (United States)

    Montesinos, Matías; Cuello, Nicolás

    2018-03-01

    Shadows and spirals seem to be common features of transition discs. Among the spiral-triggering mechanisms proposed, only one establishes a causal link between shadows and spirals so far. In fact, provided the presence of shadows in the disc, the combined effect of temperature gradient and differential disc rotation creates strong azimuthal pressure gradients. After several thousand years, grand-design spirals develop in the gas phase. Previous works have only considered static shadows caused by an inclined inner disc. However, in some cases, the inner regions of circumbinary discs can break and precess. Thus, it is more realistic to consider moving shadow patterns in the disc. In this configuration, the intersection between the inner and the outer discs defines the line of nodes at which the shadows are cast. Here, we consider moving shadows and study the resulting circumbinary disc structure. We find that only static and prograde shadows trigger spirals, in contrast to retrograde ones. Interestingly, if a region of the disc corotates with the shadow, a planet-like signature develops at the co-rotation position. The resulting spirals resemble those caused by a planet embedded in the disc, with similar pitch angles.

  8. Robust Lane Sensing and Departure Warning under Shadows and Occlusions

    Directory of Open Access Journals (Sweden)

    Miguel Torres-Torriti

    2013-03-01

    Full Text Available A prerequisite for any system that enhances drivers’ awareness of road conditions and threatening situations is the correct sensing of the road geometry and the vehicle’s relative pose with respect to the lane despite shadows and occlusions. In this paper we propose an approach for lane segmentation and tracking that is robust to varying shadows and occlusions. The approach involves color-based clustering, the use of MSAC for outlier removal and curvature estimation, and also the tracking of lane boundaries. Lane boundaries are modeled as planar curves residing in 3D-space using an inverse perspective mapping, instead of the traditional tracking of lanes in the image space, i.e., the segmented lane boundary points are 3D points in a coordinate frame fixed to the vehicle that have a depth component and belong to a plane tangent to the vehicle’s wheels, rather than 2D points in the image space without depth information. The measurement noise and disturbances due to vehicle vibrations are reduced using an extended Kalman filter that involves a 6-DOF motion model for the vehicle, as well as measurements about the road’s banking and slope angles. Additional contributions of the paper include: (i the comparison of textural features obtained from a bank of Gabor filters and from a GMRF model; and (ii the experimental validation of the quadratic and cubic approximations to the clothoid model for the lane boundaries. The results show that the proposed approach performs better than the traditional gradient-based approach under different levels of difficulty caused by shadows and occlusions.

  9. Reliability Methods for Shield Design Process

    Science.gov (United States)

    Tripathi, R. K.; Wilson, J. W.

    2002-01-01

    Providing protection against the hazards of space radiation is a major challenge to the exploration and development of space. The great cost of added radiation shielding is a potential limiting factor in deep space operations. In this enabling technology, we have developed methods for optimized shield design over multi-segmented missions involving multiple work and living areas in the transport and duty phase of space missions. The total shield mass over all pieces of equipment and habitats is optimized subject to career dose and dose rate constraints. An important component of this technology is the estimation of two most commonly identified uncertainties in radiation shield design, the shielding properties of materials used and the understanding of the biological response of the astronaut to the radiation leaking through the materials into the living space. The largest uncertainty, of course, is in the biological response to especially high charge and energy (HZE) ions of the galactic cosmic rays. These uncertainties are blended with the optimization design procedure to formulate reliability-based methods for shield design processes. The details of the methods will be discussed.

  10. Reactor shielding. Report of a panel

    International Nuclear Information System (INIS)

    1964-01-01

    Reactor shielding is necessary that people may work and live in the vicinity of reactors without receiving detrimental biological effects and that the necessary materials and instrumentation for reactor operation may function properly. Much of the necessary theoretical work and experimental measurement has been accomplished in recent years. Scientists have developed some very sophisticated methods which have contributed to a more thorough understanding of the problems involved and have produced some very reliable results leading to significant reductions in shield configurations. A panel of experts was convened from 9 to 13 March 1964 in Vienna at the Headquarters of the International Atomic Energy Agency to discuss the present status of reactor shielding. The participants were prominent shielding experts from most of the laboratories engaged in this field throughout the world. They presented status reports describing the past history and plans for further development of reactor shielding in their countries and much valuable discussion took place on some of the most relevant aspects of reactor shielding. All this material is presented in this report, together with abstracts of the supporting papers read to the Panel

  11. Shielding requirements for particle bed propulsion systems

    Science.gov (United States)

    Gruneisen, S. J.

    1991-06-01

    Nuclear Thermal Propulsion systems present unique challenges in reliability and safety. Due to the radiation incident upon all components of the propulsion system, shielding must be used to keep nuclear heating in the materials within limits; in addition, electronic control systems must be protected. This report analyzes the nuclear heating due to the radiation and the shielding required to meet the established criteria while also minimizing the shield mass. Heating rates were determined in a 2000 MWt Particle Bed Reactor (PBR) system for all materials in the interstage region, between the reactor vessel and the propellant tank, with special emphasis on meeting the silicon dose criteria. Using a Lithium Hydride/Tungsten shield, the optimum shield design was found to be: 50 cm LiH/2 cm W on the axial reflector in the reactor vessel and 50 cm LiH/2 cm W in a collar extension of the inside shield outside of the pressure vessel. Within these parameters, the radiation doses in all of the components in the interstage and lower tank regions would be within acceptable limits for mission requirements.

  12. Innovative technologies for Faraday shield cooling

    International Nuclear Information System (INIS)

    Rosenfeld, J.H.; Lindemuth, J.E.; North, M.T.; Goulding, R.H.

    1995-01-01

    Alternative advanced technologies are being evaluated for use in cooling the Faraday shields used for protection of ion cyclotron range of frequencies (ICR) antennae in Tokamaks. Two approaches currently under evaluation include heat pipe cooling and gas cooling. A Monel/water heat pipe cooled Faraday shield has been successfully demonstrated. Heat pipe cooling offers the advantage of reducing the amount of water discharged into the Tokamak in the event of a tube weld failure. The device was recently tested on an antenna at Oak Ridge National Laboratory. The heat pipe design uses inclined water heat pipes with warm water condensers located outside of the plasma chamber. This approach can passively remove absorbed heat fluxes in excess of 200 W/cm 2 ;. Helium-cooled Faraday shields are also being evaluated. This approach offers the advantage of no liquid discharge into the Tokamak in the event of a tube failure. Innovative internal cooling structures based on porous metal cooling are being used to develop a helium-cooled Faraday shield structure. This approach can dissipate the high heat fluxes typical of Faraday shield applications while minimizing the required helium blower power. Preliminary analysis shows that nominal helium flow and pressure drop can sufficiently cool a Faraday shield in typical applications. Plans are in progress to fabricate and test prototype hardware based on this approach

  13. Potential of Nanocellulose Composite for Electromagnetic Shielding

    Directory of Open Access Journals (Sweden)

    Nabila Yah Nurul Fatihah

    2017-01-01

    Full Text Available Nowadays, most people rely on the electronic devices for work, communicating with friends and family, school and personal enjoyment. As a result, more new equipment or devices operates in higher frequency were rapidly developed to accommodate the consumers need. However, the demand of using wireless technology and higher frequency in new devices also brings the need to shield the unwanted electromagnetic signals from those devices for both proper operation and human health concerns. This paper highlights the potential of nanocellulose for electromagnetic shielding using the organic environmental nanocellulose composite materials. In addition, the theory of electromagnetic shielding and recent development of green and organic material in electromagnetic shielding application has also been reviewed in this paper. The use of the natural fibers which is nanocelllose instead of traditional reinforcement materials provides several advantages including the natural fibers are renewable, abundant and low cost. Furthermore, added with other advantages such as lightweight and high electromagnetic shielding ability, nanocellulose has a great potential as an alternative material for electromagnetic shielding application.

  14. Asymptotic Ergodic Capacity Analysis of Composite Lognormal Shadowed Channels

    KAUST Repository

    Ansari, Imran Shafique

    2015-05-01

    Capacity analysis of composite lognormal (LN) shadowed links, such as Rician-LN, Gamma-LN, and Weibull-LN, is addressed in this work. More specifically, an exact closed-form expression for the moments of the end-to-end signal-to-noise ratio (SNR) of a single composite link transmission system is presented in terms of well- known elementary functions. Capitalizing on these new moments expressions, we present asymptotically tight lower bounds for the ergodic capacity at high SNR. All the presented results are verified via computer-based Monte-Carlo simulations. © 2015 IEEE.

  15. Polarization-encoded optical shadow-casting logic units: design.

    Science.gov (United States)

    Karim, M A; Awwal, A A; Cherri, A K

    1987-07-15

    A general design algorithm is presented for the multioutput polarization-encoded optical shadow-casting scheme. A set of POSC equations is obtained from the truth table of the desired logic unit and is solved in terms of four possible pixel characteristics (transparent, opaque, vertically polarized, and horizontally polarized) and four possible source characteristics (off, unpolarized, vertically polarized, and horizontally polarized). To demonstrate its feasibility, the algorithm is used to determine the input pixel characteristics of a full adder and a full subtracter.

  16. Shadows and strong gravitational lensing: a brief review

    Science.gov (United States)

    Cunha, Pedro V. P.; Herdeiro, Carlos A. R.

    2018-04-01

    For ultra compact objects, light rings and fundamental photon orbits (FPOs) play a pivotal role in the theoretical analysis of strong gravitational lensing effects, and of BH shadows in particular. In this short review, specific models are considered to illustrate how FPOs can be useful in order to understand some non-trivial gravitational lensing effects. This paper aims at briefly overviewing the theoretical foundations of these effects, touching also some of the related phenomenology, both in general relativity and alternative theories of gravity, hopefully providing some intuition and new insights for the underlying physics, which might be critical when testing the Kerr black hole hypothesis.

  17. CONSTRUCTING A COURSE ON INDONESIAN SHADOW PUPPETS FOR INTERNATIONAL STUDENTS

    Directory of Open Access Journals (Sweden)

    Yosep Bambang Margono Slamet

    2014-12-01

    Full Text Available Abstract: This paper is a course design on Indonesian shadow puppet to promote Indonesian culture to international students as a way of building a cultural bridge to create global citizens. In todays world, it is of paramount importance for every individual from diverse cultural, linguistic, and ethnic backgrounds to understand each other and work together. Creating this course is to introduce and promote an aspect Indonesian culture so that international students are more interested in and knowledgeable of Indonesian people and culture in general. Even though students only learn an aspect of Indonesian culture it is expected that they will be able to explore Indonesian culture in a broad sense.

  18. When a giant falls, dwarfs have no shadow

    OpenAIRE

    Juan Gérvas; Mercedes Pérez Fernández

    2011-01-01

    It is said that in times of war old people bury young men. As we live in times of peace, and we are old, youngsters will need to bury us. It is said that we become good people after we die. But some of us were good before dying. They were good, generous and honored, wise and tender, effectively human. Some who passed away used to give us a cozy and protective shadow, and their absence leaves us unsheltered, alone with danger. A long time ago, one of our children asked to us: “When an old wise...

  19. Congestion management in a smart grid via shadow prices

    DEFF Research Database (Denmark)

    Biegel, Benjamin; Andersen, Palle; Stoustrup, Jakob

    2012-01-01

    We consider a distribution grid interconnecting a number of consumers with flexible power consumption. Each consumer is under the jurisdiction of exactly one balancing responsible party (BRP), who buys energy at a day-ahead electricity market on behalf of the consumer. We illustrate how BRPs can...... utilize the flexibility of the consumers to minimize the imbalance between the consumed and the purchased energy thereby avoiding trading balancing energy at unfavorable prices. Further we show how shadow prices on the distribution lines can be used to resolve grid congestion without information sharing...

  20. Shadow Affect in Urban Digital (Post Screen) Art

    DEFF Research Database (Denmark)

    Toft, Tanya Søndergaard

    2014-01-01

    The paper considers an affective turn in artistic practices with interactive urban digital screen-based art that evokes a behavioral response in the audience, which I propose as a symptom of the post screen. I propose the affective experience as a mode of exploring presence in the artwork through...... “shadow affect”, as an alternative to experiencing self identification and representation. I argue that a phenomenological understanding is necessary in place of a techno-aesthetic perspective, which would allow for more nuanced understandings of human experience in our digital reality....

  1. Development of simplified methods and data bases for radiation shielding calculations for concrete

    Energy Technology Data Exchange (ETDEWEB)

    Bhuiyan, S.I.; Roussin, R.W.; Lucius, J.L.; Marable, J.H.; Bartine, D.A.

    1986-06-01

    Two simplified methods have been developed which allow rapid and accurate calculations of the attenuation of neutrons and gamma rays through concrete shields. One method, called the BEST method, uses sensitivity coefficients to predict changes in the transmitted dose from a fission source that are due to changes in the composition of the shield. The other method uses transmission factors based on adjoint calculations to predict the transmitted dose from an arbitrary source incident on a given shield. The BEST method, utilizing an exponential molecule that is shown to be a significant improvement over the traditional linear model, has been successfully applied to slab shields of standard concrete and rebar concrete. It has also been tested for a special concrete that has been used in many shielding experiments at the ORNL Tower Shielding Facility, as well as for a deep-penetration sodium problem. A comprehensive data base of concrete sensitivity coefficients generated as part of this study is available for use in the BEST model. For problems in which the changes are energy independent, application of the model and data base can be accomplished with a desk calculator. Larger-scale calculations required for problems that are energy dependent are facilitated by employing a simple computer code, which is included, together with the data base and other calculational aids, in a data package that can be obtained from the ORNL Radiation Shielding Information Center (request DLC-102/CONSENT). The transmission factors used by the second method are a byproduct of the sensitivity calculations and are mathematically equivalent to the surface adjoint function phi*, which gives the dose equivalent transmitted through a slab of thickness T due to one particle incident on the surface in the gth energy group and jth direction. 18 refs., 1 fig., 50 tabs.

  2. Numerical Models for the Study of Electromagnetic Shielding

    Directory of Open Access Journals (Sweden)

    POPA Monica

    2012-10-01

    Full Text Available The paper presents 2D and 3D models for the study of electromagnetic shielding of a coil. The magnetic fields are computed for defining the shielding effectiveness. Parametrized numerical studies were performed in order to established the influence of shield thickness and height on magnetic field in certain points located in the exterior of coil – shield setup and on induced power within the shield.

  3. Space Shielding Materials for Prometheus Application

    Energy Technology Data Exchange (ETDEWEB)

    R. Lewis

    2006-01-20

    At the time of Prometheus program restructuring, shield material and design screening efforts had progressed to the point where a down-selection from approximately eighty-eight materials to a set of five ''primary'' materials was in process. The primary materials were beryllium (Be), boron carbide (B{sub 4}C), tungsten (W), lithium hydride (LiH), and water (H{sub 2}O). The primary materials were judged to be sufficient to design a Prometheus shield--excluding structural and insulating materials, that had not been studied in detail. The foremost preconceptual shield concepts included: (1) a Be/B{sub 4}C/W/LiH shield; (2) a Be/B{sub 4}C/W shield; (3) and a Be/B{sub 4}C/H{sub 2}O shield. Since the shield design and materials studies were still preliminary, alternative materials (e.g., {sup nal}B or {sup 10}B metal) were still being screened, but at a low level of effort. Two competing low mass neutron shielding materials are included in the primary materials due to significant materials uncertainties in both. For LiH, irradiation-induced swelling was the key issue, whereas for H{sub 2}O, containment corrosion without active chemistry control was key, Although detailed design studies are required to accurately estimate the mass of shields based on either hydrogenous material, both are expected to be similar in mass, and lower mass than virtually any alternative. Unlike Be, W, and B{sub 4}C, which are not expected to have restrictive temperature limits, shield temperature limits and design accommodations are likely to be needed for either LiH or H{sub 2}O. The NRPCT focused efforts on understanding swelting of LiH, and observed, from approximately fifty prior irradiation tests, that either casting ar thorough out-gassing should reduce swelling. A potential contributor to LiH swelling appears to be LiOH contamination due to exposure to humid air, that can be eliminated by careful processing. To better understand LiH irradiation performance and

  4. Experimental results of neutron fluence outside an iron shield in the forward direction

    International Nuclear Information System (INIS)

    Torres, M.M.C.; Elwyn, A.J.; Fein, D.; James, E.; Johns, K.; Davis, W.; Ciampa, D.P.; Mierkiewicz, E.

    1996-09-01

    Analyses of both lateral shielding measurements and Monte Carlo calculations for beam stop geometry for incident hadrons at energies between 10 GeV and 10 TeV suggests that the dose equivalent can be represented by the expression H = H 0 (E)e -r/λ /r 2 where H, is the source term, r is the radial distance to the point of interest in the shield, and λ is the effective interaction length, or absorption mean free path. However, unlike the lateral shielding case, there is no similarly simple analytical expression that can be used to describe the on-axis longitudinal cascade development. In this study the results from the measurement in the forward direction of neutron fluence spectra (and the derived quantity dose equivalent) for 25 to 150 GeV pions incident on an iron beam stop as a function of thickness of iron are presented. The observed dependence of both fluence and dose equivalent on shield thickness and hadron energy was then quantified in terms of an expression in which a build up factor as well as an attenuation term was included. On the basis of this analysis the conversion factor from fluence to dose equivalent was also determined for these forward going neutrons. This work represents the first systematic study at an high energy accelerator of the depth dependence of neutron fluence in longitudinal shielding

  5. Shielding technology for high energy radiation production facility

    International Nuclear Information System (INIS)

    Lee, Byung Chul; Kim, Heon Il

    2004-06-01

    In order to develop shielding technology for high energy radiation production facility, references and data for high energy neutron shielding are searched and collected, and calculations to obtain the characteristics of neutron shield materials are performed. For the evaluation of characteristics of neutron shield material, it is chosen not only general shield materials such as concrete, polyethylene, etc., but also KAERI developed neutron shields of High Density PolyEthylene (HDPE) mixed with boron compound (B 2 O 3 , H 2 BO 3 , Borax). Neutron attenuation coefficients for these materials are obtained for later use in shielding design. The effect of source shape and source angular distribution on the shielding characteristics for several shield materials is examined. This effect can contribute to create shielding concept in case of no detail source information. It is also evaluated the effect of the arrangement of shield materials using current shield materials. With these results, conceptual shielding design for PET cyclotron is performed. The shielding composite using HDPE and concrete is selected to meet the target dose rate outside the composite, and the dose evaluation is performed by configuring the facility room conceptually. From the result, the proper shield configuration for this PET cyclotron is proposed

  6. Leaking privacy and shadow profiles in online social networks.

    Science.gov (United States)

    Garcia, David

    2017-08-01

    Social interaction and data integration in the digital society can affect the control that individuals have on their privacy. Social networking sites can access data from other services, including user contact lists where nonusers are listed too. Although most research on online privacy has focused on inference of personal information of users, this data integration poses the question of whether it is possible to predict personal information of nonusers. This article tests the shadow profile hypothesis, which postulates that the data given by the users of an online service predict personal information of nonusers. Using data from a disappeared social networking site, we perform a historical audit to evaluate whether personal data of nonusers could have been predicted with the personal data and contact lists shared by the users of the site. We analyze personal information of sexual orientation and relationship status, which follow regular mixing patterns in the social network. Going back in time over the growth of the network, we measure predictor performance as a function of network size and tendency of users to disclose their contact lists. This article presents robust evidence supporting the shadow profile hypothesis and reveals a multiplicative effect of network size and disclosure tendencies that accelerates the performance of predictors. These results call for new privacy paradigms that take into account the fact that individual privacy decisions do not happen in isolation and are mediated by the decisions of others.

  7. Tomographic Particle Image Velocimetry using Smartphones and Colored Shadows

    KAUST Repository

    Aguirre-Pablo, Andres A.

    2017-06-12

    We demonstrate the viability of using four low-cost smartphone cameras to perform Tomographic PIV. We use colored shadows to imprint two or three different time-steps on the same image. The back-lighting is accomplished with three sets of differently-colored pulsed LEDs. Each set of Red, Green & Blue LEDs is shone on a diffuser screen facing each of the cameras. We thereby record the RGB-colored shadows of opaque suspended particles, rather than the conventionally used scattered light. We subsequently separate the RGB color channels, to represent the separate times, with preprocessing to minimize noise and cross-talk. We use commercially available Tomo-PIV software for the calibration, 3-D particle reconstruction and particle-field correlations, to obtain all three velocity components in a volume. Acceleration estimations can be done thanks to the triple pulse illumination. Our test flow is a vortex ring produced by forcing flow through a circular orifice, using a flexible membrane, which is driven by a pressurized air pulse. Our system is compared to a commercial stereoscopic PIV system for error estimations. We believe this proof of concept experiment will make this technique available for education, industry and scientists for a fraction of the hardware cost needed for traditional Tomo-PIV.

  8. Racing the Moon’s shadow with Concorde 001

    CERN Document Server

    Léna, Pierre

    2015-01-01

    This is the unique story of  observing a total solar exlipse for no less than 74 consecutive minutes. On the summer morning of June 30, 1973, the Sun rises on the Canary Islands. But it is strangely indented by the Moon. The eclipse of the century has just begun. From the west, the lunar shadow rushes to the African coast at a velocity of over 2000 kilometers per hour. Astronomers on the ground will enjoy seven short minutes of total eclipse to study the solar corona - too short for Pierre Lena and seven scientists who board the Concorde 001 prototype, an extraordinary plane to become the first commercial supersonic aircraft. With André Turcat as chief pilot and a crew of five, at 17000 m altitude, the aircraft remains in the lunar shadow for 74 minutes, a record time of scientific observations not yet beaten and allowing for exceptional measurements. Science, technology, aviation and history combine in the story of a unique human adventure aboard a legendary aircraft, illustrated with a rich and original ...

  9. Tomographic Particle Image Velocimetry using Smartphones and Colored Shadows.

    Science.gov (United States)

    Aguirre-Pablo, Andres A; Alarfaj, Meshal K; Li, Er Qiang; Hernández-Sánchez, J F; Thoroddsen, Sigurdur T

    2017-06-16

    We demonstrate the viability of using four low-cost smartphone cameras to perform Tomographic PIV. We use colored shadows to imprint two or three different time-steps on the same image. The back-lighting is accomplished with three sets of differently-colored pulsed LEDs. Each set of Red, Green & Blue LEDs is shone on a diffuser screen facing each of the cameras. We thereby record the RGB-colored shadows of opaque suspended particles, rather than the conventionally used scattered light. We subsequently separate the RGB color channels, to represent the separate times, with preprocessing to minimize noise and cross-talk. We use commercially available Tomo-PIV software for the calibration, 3-D particle reconstruction and particle-field correlations, to obtain all three velocity components in a volume. Acceleration estimations can be done thanks to the triple pulse illumination. Our test flow is a vortex ring produced by forcing flow through a circular orifice, using a flexible membrane, which is driven by a pressurized air pulse. Our system is compared to a commercial stereoscopic PIV system for error estimations. We believe this proof of concept experiment will make this technique available for education, industry and scientists for a fraction of the hardware cost needed for traditional Tomo-PIV.

  10. Testing the Concept of Drift Shadow at Yucca Mountain, Nevada

    International Nuclear Information System (INIS)

    J.B. Paces; L.A. Neymark; T. Ghezzehei; P.F. Dobson

    2006-01-01

    If proven, the concept of drift shadow, a zone of reduced water content and slower ground-water travel time beneath openings in fractured rock of the unsaturated zone, may increase performance of a proposed geologic repository for high-level radioactive waste at Yucca Mountain. To test this concept under natural-flow conditions present in the proposed repository horizon, isotopes within the uranium-series decay chain (uranium-238, uranium-234, and thorium-230, or 238 U- 234 U- 230 Th) have been analyzed in samples of rock from beneath four naturally occurring lithophysal cavities. All samples show 234 U depletion relative to parent 238 U, indicating varying degrees of water-rock interaction over the past million years. Variations in 234 U/ 238 U activity ratios indicate that depletion of 234 U relative to 238 U can be either smaller or greater in rock beneath cavity floors relative to rock near cavity margins. These results are consistent with the concept of drift shadow and with numerical simulations of meter-scale spherical cavities in fractured tuff. Differences in distribution patterns of 234 U/ 238 U activity ratios in rock beneath the cavity floors are interpreted to reflect differences in the amount of past seepage into lithophysal cavities, as indicated by the abundance of secondary mineral deposits present on the cavity floors

  11. Tomographic Particle Image Velocimetry Using Colored Shadow Imaging

    KAUST Repository

    Alarfaj, Meshal K.

    2016-02-01

    Tomographic Particle Image Velocimetry Using Colored Shadow Imaging by Meshal K Alarfaj, Master of Science King Abdullah University of Science & Technology, 2015 Tomographic Particle image velocimetry (PIV) is a recent PIV method capable of reconstructing the full 3D velocity field of complex flows, within a 3-D volume. For nearly the last decade, it has become the most powerful tool for study of turbulent velocity fields and promises great advancements in the study of fluid mechanics. Among the early published studies, a good number of researches have suggested enhancements and optimizations of different aspects of this technique to improve the effectiveness. One major aspect, which is the core of the present work, is related to reducing the cost of the Tomographic PIV setup. In this thesis, we attempt to reduce this cost by using an experimental setup exploiting 4 commercial digital still cameras in combination with low-cost Light emitting diodes (LEDs). We use two different colors to distinguish the two light pulses. By using colored shadows with red and green LEDs, we can identify the particle locations within the measurement volume, at the two different times, thereby allowing calculation of the velocities. The present work tests this technique on the flows patterns of a jet ejected from a tube in a water tank. Results from the images processing are presented and challenges discussed.

  12. Improving Shadow Suppression for Illumination Robust Face Recognition

    KAUST Repository

    Zhang, Wuming

    2017-10-13

    2D face analysis techniques, such as face landmarking, face recognition and face verification, are reasonably dependent on illumination conditions which are usually uncontrolled and unpredictable in the real world. An illumination robust preprocessing method thus remains a significant challenge in reliable face analysis. In this paper we propose a novel approach for improving lighting normalization through building the underlying reflectance model which characterizes interactions between skin surface, lighting source and camera sensor, and elaborates the formation of face color appearance. Specifically, the proposed illumination processing pipeline enables the generation of Chromaticity Intrinsic Image (CII) in a log chromaticity space which is robust to illumination variations. Moreover, as an advantage over most prevailing methods, a photo-realistic color face image is subsequently reconstructed which eliminates a wide variety of shadows whilst retaining the color information and identity details. Experimental results under different scenarios and using various face databases show the effectiveness of the proposed approach to deal with lighting variations, including both soft and hard shadows, in face recognition.

  13. Shielding design for positron emission tomography facility

    International Nuclear Information System (INIS)

    Abdallah, I.I.

    2007-01-01

    With the recent advent of readily available tracer isotopes, there has been marked increase in the number of hospital-based and free-standing positron emission tomography (PET) clinics. PET facilities employ relatively large activities of high-energy photon emitting isotopes, which can be dangerous to the health of humans and animals. This coupled with the current dose limits for radiation worker and members of the public can result in shielding requirements. This research contributes to the calculation of the appropriate shielding to keep the level of radiation within an acceptable recommended limit. Two different methods were used including measurements made at selected points of an operating PET facility and computer simulations by using Monte Carlo Transport Code. The measurements mainly concerned the radiation exposure at different points around facility using the survey meter detectors and Thermoluminescent Dosimeters (TLD). Then the set of manual calculation procedures were used to estimate the shielding requirements for a newly built PEF facility. The results from the measurement and the computer simulation were compared to the results obtained from the set manual calculation procedure. In general, the estimated weekly dose at the points of interest is lower than the regulatory limits for the little company of Mary Hospital. Furthermore, the density and the HVL for normal strength concrete and clay bricks are almost similar. In conclusion, PET facilities present somewhat different design requirements and are more likely to require additional radiation shielding. Therefore, existing shields at the little Company of Mary Hospital are in general found to be adequate and satisfactory and additional shielding was found necessary at the new PET facility in the department of Nuclear Medicine of the Dr. George Mukhari Hospital. By use of appropriate design, by implying specific shielding requirements and by maintaining good operating practices, radiation doses to

  14. Application of ceramics for neutron shielding. Proposal of multi-functional shielding materials

    Energy Technology Data Exchange (ETDEWEB)

    Senda, Tetsuya; Akiyama, Shigeru; Matsuoka, Kazuyoshi; Ueki, Kohtaro; Ohashi, Atsuto [Ship Research Inst., Mitaka, Tokyo (Japan); Amada, Shigeyasu [Gunma Univ., Maebashi (Japan)

    1999-09-01

    Radiation shielding is one of the fundamental technologies to ensure the safety of the nuclear plants. Particularly for the nuclear systems as the power plants of ships and undersea vehicles, radiation shielding should be achieved within limited space and weight. Ceramics are of great interest as shielding components, because they can be composed with a wide variation of elements that have different shielding specifications. They are also known as good structural materials at high temperatures. Therefore, ceramics may be promising as 'multi-functional' shielding materials. In the present study, neutron shielding effects are first investigated by a series of the experiments using a {sup 252}Cf neutron source and simulated by using Monte Carlo Code MCNP 4A. The role of each ceramics is discussed particularly in terms of the 'enhancement effect' by medium-heavy elements, such as chromium and titanium. As an advanced technique to evaluate the thermal shock resistance of the materials, a laser irradiation method is proposed and applied to those ceramics that are expected to be neutron shielding components. Detailed discussion is made on the effects of porosity and multiple irradiation resulting in a fatigue-like behavior. Based on the results of these experiments and simulations, a three-layered arrangement, consisting of chromium carbide, titanium boride and boron nitride, is proposed as a multi-functional shielding material that minimizes the dose-equivalent rate and also exhibits good thermal shock resistance. (author)

  15. Comparison of eye shields in radiotherapeutic beams

    International Nuclear Information System (INIS)

    Currie, B.E.; Wellington Hospital, Wellington; Johnson, A.D.

    2004-01-01

    Full text: Both MeV electrons and kV photons are used in the treatment of superficial cancers. The advantages and disadvantages for each of these modalities have been widely reported in the literature (See for example [1-2]). Of particular note in the literature is the use of lead and tungsten eye shields to protect ocular structures during radiotherapy. An investigation addressing issues raised in the literature that are relevant to the Wellington Cancer Centre method of treatment of lesions near the eye shall be summarised. Various small sized fields were irradiated to determine depth dose and profile curves in a water phantom shielded by various commercially available eye shields. Transmission factors relevant to critical ocular structures and particle distribution theories are used to further elucidate the comparison between the use of MeV electrons and kV photons in the treatment of superficial cancers. Superficial X-rays from a Pantak Therapax unit SXT 150 model of HVL 4.90mm Al were used for the lead eye shield measurements and electrons from a Varian Clinac 2100C nominal energies 6MeV and 9MeV (R p 3.00cm and 4.34cm respectively) were used for the tungsten eye shield measurements. For the photon measurements circular applicators of 3cm, 4cm and 5cm diameter were used and for the electrons standard 6x6cm and 10x 10cm applicators were used, with no custom inserts. A Scanditronix RFA-300 water phantom and Scanditronix RFAplus version 5.3 software application were used to collect and collate all data. The eye shields were the Radiation Products Design Inc. medium lead eye shield (item 934-014) and the MED-TEC tungsten eye shields MT-T-45 M and MT-T-45 S. It is demonstrated that electron fields have appreciably greater scatter into the area directly under the eye shields than the photon fields. Similarly at the region of d max for the electron fields the relative dose is appreciably greater than the photon fields at similar depth. The relative merits for

  16. The effect of shadow lines on a low concentrating photovoltaic system

    NARCIS (Netherlands)

    Janssen, H.J.J.; Sonneveld, P.J.; Swinkels, G.L.A.M.; Tuijl, van B.A.J.; Zwart, de H.F.

    2011-01-01

    In order to reduce the energy losses caused by shadow lines, three options are investigated. These are: 1. the use of two types of diodes; 2. the use of an ”ideal” diode based an active bypass by using MOS-FET’s [4] and 3. parallel switching of a number of cells between two shadow lines. The first

  17. The Job Shadow Assignment: Career Perceptions in Hospitality, Recreation and Tourism

    Science.gov (United States)

    Padron, Thomas C.; Fortune, Mary F.; Spielman, Melany; Tjoei, Sylvie

    2017-01-01

    The job shadow study measured student career perceptions related to hospitality, recreation and tourism (HRT) and instructional mode (face-to-face (F2F), hybrid, and online). College students self-selecting into three different course modalities taught by the same instructor job shadowed HRT professionals by using Internet and F2F interviews. The…

  18. Shadow Education in Spain: Examining Social Inequalities through the Analysis of PISA Results

    Science.gov (United States)

    Runte-Geidel, Ariadne; Marzo, Pedro Femia

    2015-01-01

    This article examines the use of shadow education by students of compulsory secondary education in Spain over the period 2000-2010. The study identifies the proportion of the student population that uses this type of education and examines how the use of shadow education has evolved during this period. Data was drawn from the student questionnaire…

  19. Discursive Shadowing in Linguistic Ethnography. Situated Practices and Circulating Discourses in Multilingual Schools

    Science.gov (United States)

    Dewilde, Joke; Creese, Angela

    2016-01-01

    We consider discursive shadowing as methodology in linguistic ethnography and how it refines our analyses of participants' situated practices. In addition to the constant and extended company the researcher and key participant keep with one another in the field, shadowing in a linguistic ethnographic approach includes the ubiquitous…

  20. Observation of the shadowing and antishadowing effects in pion-nucleus interactions

    International Nuclear Information System (INIS)

    Ion, D.B.; Nichitiu, F.

    1977-12-01

    The shadowing and antishadowing effects in the pion-nucleus interaction are investigated by using the available experimental data and the recent interpolations of the π + - p total cross sections. Pronounced shadowing is found in the energy regions of pion-nucleon resonances while the antishadowing effects are systematically observed at energies between two resonances. (author)

  1. Labor Market Institutions and Their Impact on Shadow Economies in Europe

    Czech Academy of Sciences Publication Activity Database

    Fialová, Kamila; Schneider, O.

    2014-01-01

    Roč. 5, č. 1 (2014), s. 1-40 ISSN 2038-1379 R&D Projects: GA ČR(CZ) GA14-15008S Institutional support: RVO:68378025 Keywords : labour market institutions * shadow economy * shadow employment Subject RIV: AH - Economics http://www.rei.unipg.it/rei/article/view/146/137

  2. A Study on Building an Efficient Job Shadowing Management Methodology for the Undergraduate Students

    Science.gov (United States)

    Sakoda, Koichi; Takahashi, Masakazu

    2014-01-01

    This paper describes heuristic knowledge through the job-shadowing project at the International University of Kagoshima, Japan. Job shadowing is one of the conventional in-house trainings given to the executive trainee cadets in North America and proved the effect of training in Leonard's paper for the conventional target such as the executive…

  3. Mapping the ultrasonic defect shadow in a pitch-catch mode

    International Nuclear Information System (INIS)

    Licht, H.; Hallet, J.B.

    1981-06-01

    In ultrasonic testing of metallic structures, the sound reflected from a discontinuity is usually used to determine its location and size. Here is described a technique for locating and sizing a discontinuity by mapping the shadow(s) it casts. A brief description of the technique is given. Results obtained from artificial notches and fatigue cracks are outlined and discussed

  4. Implementing content constraints in alpha-stratified adaptive testing using a shadow test approach

    NARCIS (Netherlands)

    van der Linden, Willem J.; Chang, Hua-Hua

    2001-01-01

    The methods of alpha-stratified adaptive testing and constrained adaptive testing with shadow tests are combined in this study. The advantages are twofold. First, application of the shadow test allows the researcher to implement any type of constraint on item selection in alpha-stratified adaptive

  5. Shadowing corrections to the derivative of the reduced cross-section ...

    Indian Academy of Sciences (India)

    where the shadowing corrections to the derivative of the parton structure functions are given by eqs (6) and (7). After substitution and rearranging [22] we find that the shad- owing correction to the longitudinal structure function is proportional to the shadowing corrections to the gluon distribution function as. Fsh. L (x, Q2) = ...

  6. Qualitative Shadowing as a Research Methodology for Exploring Early Childhood Leadership in Practice

    Science.gov (United States)

    Bøe, Marit; Hognestad, Karin; Waniganayake, Manjula

    2017-01-01

    This article explores qualitative shadowing as an interpretivist methodology, and explains how two researchers participating simultaneously in data collection using a video recorder, contextual interviews and video-stimulated recall interviews, conducted a qualitative shadowing study at six early childhood centres in Norway. This paper emerged…

  7. Art Therapy and Its Shadow: A Jungian Perspective on Professional Identity and Community.

    Science.gov (United States)

    Bouchard, Rene R.

    1998-01-01

    Through the lens of Jungian theory of the shadow, this article identifies ways in which its dynamics and manifestations occur in the field of art therapy. Introduces experiential exercises for discovering and working with the shadow and concludes with recommendations for transforming negative dynamics into creative solutions. (Author/MKA)

  8. effect of shadowing and multipath fading on the area spectral for cell

    African Journals Online (AJOL)

    user

    base station. This is because of excess attenuation of the signal due to fading and shadowing. Multipath fading and shadowing are major causes of performance degradation in mobile communication systems. This phenomenon which arises as a result of propagation effects (like scattering, diffraction and reflection), renders ...

  9. STUDY ON SHADOW EFFECTS OF VARIOUS FEATURES ON CLOSE RANGE THERMAL IMAGES

    Directory of Open Access Journals (Sweden)

    C. L. Liao

    2012-07-01

    Full Text Available Thermal infrared data become more popular in remote sensing investigation, for it could be acquired both in day and night. The change of temperature has special characteristic in natural environment, so the thermal infrared images could be used in monitoring volcanic landform, the urban development, and disaster prevention. Heat shadow is formed by reflecting radiating capacity which followed the objects. Because of poor spatial resolution of thermal infrared images in satellite sensor, shadow effects were usually ignored. This research focus on discussing the shadow effects of various features, which include metals and nonmetallic materials. An area-based thermal sensor, FLIR-T360 was selected to acquire thermal images. Various features with different emissivity were chosen as reflective surface to obtain thermal shadow in normal atmospheric temperature. Experiments found that the shadow effects depend on the distance between sensors and features, depression angle, object temperature and emissivity of reflective surface. The causes of shadow effects have been altered in the experiment for analyzing the variance in thermal infrared images. The result shows that there were quite different impacts by shadow effects between metals and nonmetallic materials. The further research would be produced a math model to describe the shadow effects of different features in the future work.

  10. A new strategy for pressed powder eye shadow analysis: allergenic metal ion content and particle size distribution.

    Science.gov (United States)

    Contado, Catia; Pagnoni, Antonella

    2012-08-15

    Nine cheap eye shadow products were analyzed through graphite furnace atomic absorption spectrometry (GF-AAS) to quantify their Cr, Co and Ni contents, all known to be skin sensitizers. In many cases, the concentrations were higher than 1 or 5 ppm (μg/g), i.e. the limits recommended in the scientific literature to minimize the risk of reaction in particularly sensitive subjects. In most cases, the concentration of Cr was higher than that of Ni and Co, up to a limit case of 150 mg/g. In this particular sample, the potential amount of Cr that could be released in ionic form was determined in sweat simulating solutions by GF-AAS and confirmed through a specific spectrofluorimetric method; the results indicated the presence of approximately 80-90 ppb (ng/g) of Cr(3+). The water dispersible particles were isolated from the eye shadow powders through a simple solvent extraction procedure. The aqueous suspensions were then sorted through sedimentation field flow fractionation (SdFFF) and the particles sizes were calculated from experimental fractograms using theory. For the most part, the computed sizes were in the micron range, as confirmed by some SEM photographs taken on fractions collected during the separations. The SdFFF coupled off-line with the GFAAS enabled elemental characterization of pigment particles as a function of size. This finding reduces the concern that the ingredients of such makeup formulations may contain nanoparticles. Copyright © 2012 Elsevier B.V. All rights reserved.

  11. Radiation shielding fiber and its manufacturing method

    International Nuclear Information System (INIS)

    Tanaka, Koji; Ono, Hiroshi.

    1988-01-01

    Purpose: To manufacture radiation shielding fibers of excellent shielding effects. Method: Fibers containing more than 1 mmol/g of carboxyl groups are bonded with heavy metals, or they are impregnated with an aqueous solution containing water-soluble heavy metal salts dissolved therein. Fibers as the substrate may be any of forms such as short fibers, long fibers, fiber tows, webs, threads, knitting or woven products, non-woven fabrics, etc. It is however necessary that fibers contain more than 1 mmol/g, preferably, from 2 to 7 mmol/g of carboxylic groups. Since heavy metals having radiation shielding performance are bonded to the outer layer of the fibers and the inherent performance of the fibers per se is possessed, excellent radiation shielding performance can be obtained, as well as they can be applied with spinning, knitting or weaving, stitching, etc. thus can be used for secondary fiber products such as clothings, caps, masks, curtains, carpets, cloths, etc. for use in radiation shieldings. (Kamimura, M.)

  12. Hydrogen Induced Cracking of Drip Shield

    Energy Technology Data Exchange (ETDEWEB)

    G. De

    2003-02-24

    One potential failure mechanism for titanium and its alloys under repository conditions is via the absorption of atomic hydrogen in the metal crystal lattice. The resulting decreased ductility and fracture toughness may lead to brittle mechanical fracture called hydrogen-induced cracking (HIC) or hydrogen embrittlement. For the current design of the engineered barrier without backfill, HIC may be a problem since the titanium drip shield can be galvanically coupled to rock bolts (or wire mesh), which may fall onto the drip shield, thereby creating conditions for hydrogen production by electrochemical reaction. The purpose of this scientific analysis and modeling activity is to evaluate whether the drip shield will fail by HIC or not under repository conditions within 10,000 years of emplacement. This Analysis and Model Report (AMR) addresses features, events, and processes related to hydrogen induced cracking of the drip shield. REV 00 of this AMR served as a feed to ''Waste Package Degradation Process Model Report'' and was developed in accordance with the activity section ''Hydrogen Induced Cracking of Drip Shield'' of the development plan entitled ''Analysis and Model Reports to Support Waste Package PMR'' (CRWMS M&O 1999a). This AMR, prepared according to ''Technical Work Plan for: Waste Package Materials Data Analyses and Modeling'' (BSC 2002), is to feed the License Application.

  13. Cosmic Ray Interactions in Shielding Materials

    Energy Technology Data Exchange (ETDEWEB)

    Aguayo Navarrete, Estanislao; Kouzes, Richard T.; Ankney, Austin S.; Orrell, John L.; Berguson, Timothy J.; Troy, Meredith D.

    2011-09-08

    This document provides a detailed study of materials used to shield against the hadronic particles from cosmic ray showers at Earth’s surface. This work was motivated by the need for a shield that minimizes activation of the enriched germanium during transport for the MAJORANA collaboration. The materials suitable for cosmic-ray shield design are materials such as lead and iron that will stop the primary protons, and materials like polyethylene, borated polyethylene, concrete and water that will stop the induced neutrons. The interaction of the different cosmic-ray components at ground level (protons, neutrons, muons) with their wide energy range (from kilo-electron volts to giga-electron volts) is a complex calculation. Monte Carlo calculations have proven to be a suitable tool for the simulation of nucleon transport, including hadron interactions and radioactive isotope production. The industry standard Monte Carlo simulation tool, Geant4, was used for this study. The result of this study is the assertion that activation at Earth’s surface is a result of the neutronic and protonic components of the cosmic-ray shower. The best material to shield against these cosmic-ray components is iron, which has the best combination of primary shielding and minimal secondary neutron production.

  14. Correlated Uncertainties in Radiation Shielding Effectiveness

    Science.gov (United States)

    Werneth, Charles M.; Maung, Khin Maung; Blattnig, Steve R.; Clowdsley, Martha S.; Townsend, Lawrence W.

    2013-01-01

    The space radiation environment is composed of energetic particles which can deliver harmful doses of radiation that may lead to acute radiation sickness, cancer, and even death for insufficiently shielded crew members. Spacecraft shielding must provide structural integrity and minimize the risk associated with radiation exposure. The risk of radiation exposure induced death (REID) is a measure of the risk of dying from cancer induced by radiation exposure. Uncertainties in the risk projection model, quality factor, and spectral fluence are folded into the calculation of the REID by sampling from probability distribution functions. Consequently, determining optimal shielding materials that reduce the REID in a statistically significant manner has been found to be difficult. In this work, the difference of the REID distributions for different materials is used to study the effect of composition on shielding effectiveness. It is shown that the use of correlated uncertainties allows for the determination of statistically significant differences between materials despite the large uncertainties in the quality factor. This is in contrast to previous methods where uncertainties have been generally treated as uncorrelated. It is concluded that the use of correlated quality factor uncertainties greatly reduces the uncertainty in the assessment of shielding effectiveness for the mitigation of radiation exposure.

  15. Shielding Development for Nuclear Thermal Propulsion

    Science.gov (United States)

    Caffrey, Jarvis A.; Gomez, Carlos F.; Scharber, Luke L.

    2015-01-01

    Radiation shielding analysis and development for the Nuclear Cryogenic Propulsion Stage (NCPS) effort is currently in progress and preliminary results have enabled consideration for critical interfaces in the reactor and propulsion stage systems. Early analyses have highlighted a number of engineering constraints, challenges, and possible mitigating solutions. Performance constraints include permissible crew dose rates (shared with expected cosmic ray dose), radiation heating flux into cryogenic propellant, and material radiation damage in critical components. Design strategies in staging can serve to reduce radiation scatter and enhance the effectiveness of inherent shielding within the spacecraft while minimizing the required mass of shielding in the reactor system. Within the reactor system, shield design is further constrained by the need for active cooling with minimal radiation streaming through flow channels. Material selection and thermal design must maximize the reliability of the shield to survive the extreme environment through a long duration mission with multiple engine restarts. A discussion of these challenges and relevant design strategies are provided for the mitigation of radiation in nuclear thermal propulsion.

  16. Short Stories About The Ocean, an Art Integrated Project Into the Elementary Curriculum, Using Shadow Theatre and Video.

    Science.gov (United States)

    Guieu, M.; Scheurle, C.

    2016-02-01

    The holistic aspect of integrated learning reflects the way our world works: everything is interconnected. Integrated Learning connects students, teachers, academic content and the world. It creates bridges between disciplines, encourages invention, experimentation, and problem solving. In an art integrated lesson or project, the students learn in a creative way, exploring a given subject by working on an art project, individually or collectively, using an array of traditional techniques and technology tools. Short Stories about the Ocean is anchored in the 4th and 5th grade curriculum, the art technique is the shadow theatre. The students videotape the performances for documentation and sharing. After giving the students information about different types of human activities that have an impact on the ocean, and discussing them, the students form groups and choose a specific subject - for example over fishing or pipe spilling. They gather more information and create a story with a beginning, a development and an end. Prior to start the project, the teacher prepares a small shadow theatre made of simple material, with a template I provide. The teacher explains the basics in shadow theatre technique. The students work with paper and skewers to create the elements they need for their story. They find solutions to render proportions, movements, actions and timing. Each group rehearses and then presents to the class a two/three minutes performance. The students who watch give a positive critique. Each group takes the time to make changes if the story, the message or the elements need to be clearer. Each group performs in front of the class again. This collaborative work encourages decision making. The students have to define their idea and concept clearly, with enough details but not too many, so that their message is understood by the viewers. It is a challenge for the students to design the shapes they need for their story with minimal material and they must be

  17. Analysis of Shield Construction in Spherical Weathered Granite Development Area

    Science.gov (United States)

    Cao, Quan; Li, Peigang; Gong, Shuhua

    2018-01-01

    The distribution of spherical weathered bodies (commonly known as "boulder") in the granite development area directly affects the shield construction of urban rail transit engineering. This paper is based on the case of shield construction of granite globular development area in Southern China area, the parameter control in shield machine selection and shield advancing during the shield tunneling in this special geological environment is analyzed. And it is suggested that shield machine should be selected for shield construction of granite spherical weathered zone. Driving speed, cutter torque, shield machine thrust, the amount of penetration and the speed of the cutter head of shield machine should be controlled when driving the boulder formation, in order to achieve smooth excavation and reduce the disturbance to the formation.

  18. Evaluation of a permanent reactor vessel head shield

    International Nuclear Information System (INIS)

    Wagner, D.S.; Johnson, T.G.; Tipswork, S.R.

    1988-01-01

    This paper reports that Virginia Power recently completed installing permanent reactor vessel head shields at all four of its nuclear units-Surry 1 and 2 (781-MWe Westinghouse PWRs) and North Anna 1 and 2 (893-MWe Westinghouse PWRs). Permanent shields were chosen over the use of temporary shielding based on a cost/benefit analysis. Factors that were taken into account in the analysis included the cost of the shields, the one-time dose commitment for installation of permanent shields, dose and manpower commitments for installation and removal of temporary shielding during each outage, decontamination and storage of temporary shielding between outages, and projected dose savings for both types of shields. Basically, permanent shields were found to be more cot-effective because each required only a one-time dose commitment for installation

  19. Uniformity Masks Design Method Based on the Shadow Matrix for Coating Materials with Different Condensation Characteristics

    Directory of Open Access Journals (Sweden)

    Lichao Zhang

    2013-01-01

    Full Text Available An intuitionistic method is proposed to design shadow masks to achieve thickness profile control for evaporation coating processes. The proposed method is based on the concept of the shadow matrix, which is a matrix that contains coefficients that build quantitive relations between shape parameters of masks and shadow quantities of substrate directly. By using the shadow matrix, shape parameters of shadow masks could be derived simply by solving a matrix equation. Verification experiments were performed on a special case where coating materials have different condensation characteristics. By using the designed mask pair with complementary shapes, thickness uniformities of better than 98% are demonstrated for MgF2 ( and LaF3 ( simultaneously on a 280 mm diameter spherical substrate with the radius curvature of 200 mm.

  20. Shadow Probability of Detection and False Alarm for Median-Filtered SAR Imagery

    Energy Technology Data Exchange (ETDEWEB)

    Raynal, Ann Marie [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). ISR Analysis and Applications Dept.; Doerry, Armin Walter [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). ISR Mission Engineering Dept.; Miller, John A. [General Atomics Aeronautical Systems, Inc., San Diego, CA (United States). Mission Systems; Bishop, Edward E. [General Atomics Aeronautical Systems, Inc., San Diego, CA (United States). Mission Systems; Horndt, Volker [General Atomics Aeronautical Systems, Inc., San Diego, CA (United States). Mission Systems

    2014-06-01

    Median filtering reduces speckle in synthetic aperture radar (SAR) imagery while preserving edges, at the expense of coarsening the resolution, by replacing the center pixel of a sliding window by the median value. For shadow detection, this approach helps distinguish shadows from clutter more easily, while preserving shadow shape delineations. However, the nonlinear operation alters the shadow and clutter distributions and statistics, which must be taken into consideration when computing probability of detection and false alarm metrics. Depending on system parameters, median filtering can improve probability of detection and false alarm by orders of magnitude. Herein, we examine shadow probability of detection and false alarm in a homogeneous, ideal clutter background after median filter post-processing. Some comments on multi-look processing effects with and without median filtering are also made.

  1. Enhancing Wave Energy Competitiveness through Co-Located Wind and Wave Energy Farms. A Review on the Shadow Effect

    Directory of Open Access Journals (Sweden)

    Sharay Astariz

    2015-07-01

    Full Text Available Wave energy is one of the most promising alternatives to fossil fuels due to the enormous available resource; however, its development may be slowed as it is often regarded as uneconomical. The largest cost reductions are expected to be obtained through economies of scale and technological progress. In this sense, the incorporation of wave energy systems into offshore wind energy farms is an opportunity to foster the development of wave energy. The synergies between both renewables can be realised through these co-located energy farms and, thus, some challenges of offshore wind energy can be met. Among them, this paper focuses on the longer non-operational periods of offshore wind turbines—relative to their onshore counterparts—typically caused by delays in maintenance due to the harsh marine conditions. Co-located wave energy converters would act as a barrier extracting energy from the waves and resulting in a shielding effect over the wind farm. On this basis, the aim of this paper is to analyse wave energy economics in a holistic way, as well as the synergies between wave and offshore wind energy, focusing on the shadow effect and the associated increase in the accessibility to the wind turbines.

  2. Brachytherapy structural shielding calculations using Monte Carlo generated, monoenergetic data

    Energy Technology Data Exchange (ETDEWEB)

    Zourari, K.; Peppa, V.; Papagiannis, P., E-mail: ppapagi@phys.uoa.gr [Medical Physics Laboratory, Medical School, University of Athens, 75 Mikras Asias, 11527 Athens (Greece); Ballester, Facundo [Department of Atomic, Molecular and Nuclear Physics, University of Valencia, Burjassot 46100 (Spain); Siebert, Frank-André [Clinic of Radiotherapy, University Hospital of Schleswig-Holstein, Campus Kiel 24105 (Germany)

    2014-04-15

    Purpose: To provide a method for calculating the transmission of any broad photon beam with a known energy spectrum in the range of 20–1090 keV, through concrete and lead, based on the superposition of corresponding monoenergetic data obtained from Monte Carlo simulation. Methods: MCNP5 was used to calculate broad photon beam transmission data through varying thickness of lead and concrete, for monoenergetic point sources of energy in the range pertinent to brachytherapy (20–1090 keV, in 10 keV intervals). The three parameter empirical model introduced byArcher et al. [“Diagnostic x-ray shielding design based on an empirical model of photon attenuation,” Health Phys. 44, 507–517 (1983)] was used to describe the transmission curve for each of the 216 energy-material combinations. These three parameters, and hence the transmission curve, for any polyenergetic spectrum can then be obtained by superposition along the lines of Kharrati et al. [“Monte Carlo simulation of x-ray buildup factors of lead and its applications in shielding of diagnostic x-ray facilities,” Med. Phys. 34, 1398–1404 (2007)]. A simple program, incorporating a graphical user interface, was developed to facilitate the superposition of monoenergetic data, the graphical and tabular display of broad photon beam transmission curves, and the calculation of material thickness required for a given transmission from these curves. Results: Polyenergetic broad photon beam transmission curves of this work, calculated from the superposition of monoenergetic data, are compared to corresponding results in the literature. A good agreement is observed with results in the literature obtained from Monte Carlo simulations for the photon spectra emitted from bare point sources of various radionuclides. Differences are observed with corresponding results in the literature for x-ray spectra at various tube potentials, mainly due to the different broad beam conditions or x-ray spectra assumed. Conclusions

  3. Determination of the neutron energy and spatial distributions of the neutron beam from the TSR-II in the large beam shield

    International Nuclear Information System (INIS)

    Clifford, C.E.; Muckenthaler, F.J.

    1976-01-01

    The TSR-II reactor of the ORNL Tower Shielding Facility has recently been relocated within a new, fixed shield. A principal feature of the new shield is a beam port of considerably larger area than that of its predecessor. The usable neutron flux has thereby been increased by a factor of approximately 200. The bare beam neutron spectrum behind the new shield has been experimentally determined over the energy range from 0.8 to 16 MeV. A high level of fission product gamma ray background prevented measurement of bare beam spectra below 0.8 MeV, however neutron spectra in the energy range from 8 keV to 1.4 MeV were obtained for two simple, calculable shielding configurations. Also measured in the present work were weighted integral flux distributions and fast neutron dose rates

  4. Passive magnetic shielding in MRI-Linac systems

    Science.gov (United States)

    Whelan, Brendan; Kolling, Stefan; Oborn, Brad M.; Keall, Paul

    2018-04-01

    Passive magnetic shielding refers to the use of ferromagnetic materials to redirect magnetic field lines away from vulnerable regions. An application of particular interest to the medical physics community is shielding in MRI systems, especially integrated MRI-linear accelerator (MRI-Linac) systems. In these systems, the goal is not only to minimize the magnetic field in some volume, but also to minimize the impact of the shield on the magnetic fields within the imaging volume of the MRI scanner. In this work, finite element modelling was used to assess the shielding of a side coupled 6 MV linac and resultant heterogeneity induced within the 30 cm diameter of spherical volume (DSV) of a novel 1 Tesla split bore MRI magnet. A number of different shield parameters were investigated; distance between shield and magnet, shield shape, shield thickness, shield length, openings in the shield, number of concentric layers, spacing between each layer, and shield material. Both the in-line and perpendicular MRI-Linac configurations were studied. By modifying the shield shape around the linac from the starting design of an open ended cylinder, the shielding effect was boosted by approximately 70% whilst the impact on the magnet was simultaneously reduced by approximately 10%. Openings in the shield for the RF port and beam exit were substantial sources of field leakage; however it was demonstrated that shielding could be added around these openings to compensate for this leakage. Layering multiple concentric shield shells was highly effective in the perpendicular configuration, but less so for the in-line configuration. Cautious use of high permeability materials such as Mu-metal can greatly increase the shielding performance in some scenarios. In the perpendicular configuration, magnetic shielding was more effective and the impact on the magnet lower compared with the in-line configuration.

  5. Calculated shielding factors for selected European houses

    International Nuclear Information System (INIS)

    Hedemann Jensen, P.

    1984-12-01

    Shielding factors for gamma radiation from activity deposited on structures and ground surfaces have been calculated with the computer model DEPSHIELD for single-family and multi-storey buildings in France, United Kingdom and Denmark. For all three countries it was found that the shielding factors for single-family houses are approximately a factor of 2 - 10 higher that those for buildings with five or more storeys. Away from doors and windows the shielding factors for French, British, and Danish single-family houses are in the range 0.03 - 0.1, 0.06 - 0.4, and 0.07 - 0.3, respectively. The uncertainties of the calculations are discussed and DEPSHIELD-results are compared with other methods as well as with experimental results. (author)

  6. Radiation safety shield for a syringe

    International Nuclear Information System (INIS)

    Tipton, H.W.

    1976-01-01

    Safety apparatus for use in administering radioactive serums by a syringe, without endangering the health and safety of the medical operators is described. The apparatus consists of a sheath and a shield which can be retracted into the sheath to assay the radioactive serum in an assay well. The shield can be moved from the retracted position into an extended position when the serum is to be injected into the patient. To protect the operator, the shield can be constructed of tantalum or any like high density substance to attenuate the radiation, emanating from the radioactive serums contained in the syringe, from passing to the atmosphere. A lead glass window is provided so that the operator can determine the exact quantity of the radioactive serum which is contained in the syringe

  7. Slipforming of reinforced concrete shield building

    International Nuclear Information System (INIS)

    Hsieh, M.C.; King, J.R.

    1982-01-01

    The unique design and construction features of slipforming the heavily reinforced concrete cylindrical shield walls at the Satsop nuclear plant in Washington, D.C. site are presented. The shield walls were designed in compliance with seismic requirements which resulted in the need for reinforcing steel averaging 326 kg/m/sup 3/. A 7.6 m high, three-deck moving platform was designed to permit easy installation of the reinforcing steel, embedments, and blockouts, and to facilitate concrete placement and finishing. Two circular box trusses, one on each side of the shield wall, were used in combination with a spider truss to meet both the tolerance and strength requirements for the slipform assembly

  8. Final design of ITER thermal shield manifold

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Kyung-Kyu [Mecha T& S, Jinju-si 52811 (Korea, Republic of); Noh, Chang Hyun, E-mail: chnoh@nfri.re.kr [National Fusion Research Institute, Daejeon 34133 (Korea, Republic of); Kim, Yun-Kyu; Park, Sungwoo [Mecha T& S, Jinju-si 52811 (Korea, Republic of); Nam, Kwanwoo [National Fusion Research Institute, Daejeon 34133 (Korea, Republic of); Chung, Wooho [Mecha T& S, Jinju-si 52811 (Korea, Republic of); Kang, Dongkwon; Kang, Kyung-O. [National Fusion Research Institute, Daejeon 34133 (Korea, Republic of); Park, Sungmun [SFA Engineering Corporation, Hwaseong-si 10060 (Korea, Republic of); Bae, Jing Do [Korea Marine Equipment Research Institute, Busan 49111 (Korea, Republic of)

    2016-11-01

    Highlights: • Engineering design of thermal shield manifold is finalized. • Pipe routing, support design and flow balance are verified by analysis. • Mock-ups are fabricated to verify the design. - Abstract: The ITER thermal shield is actively cooled by 80 K pressurized helium gas. The helium coolant flows from the cold valve box to the cooling tubes on the TS panels via manifold piping. This paper describes the final design of thermal shield manifold. Pipe design to accommodate the thermal contraction considering interface with adjacent components and detailed design of support structure are presented. R&D for the pipe branch connection is carried out to find a feasible manufacturing method. Global structural behavior and structural integrity of the manifold including pipe supports are investigated by a finite element analysis based on ASME B31.3 code. Flow analyses are performed to check the flow distribution.

  9. Progress of the ITER Thermal Shields

    Energy Technology Data Exchange (ETDEWEB)

    Her, Namil, E-mail: namil.her@iter.org [ITER Organisation, Route de Vinon-sur-Verdon – CS 90046, 13067 St Paul-lez-Durance Cedex (France); Hick, Robby; Le Barbier, Robin; Arzoumanian, Terenig; Choi, Chang-Ho; Sborchia, Carlo [ITER Organisation, Route de Vinon-sur-Verdon – CS 90046, 13067 St Paul-lez-Durance Cedex (France); Chung, Wooho; Nam, Kwanwoo; Noh, Chang Hyun; Kang, Dong Kwon; Kang, Gyoung-O. [ITER Korea, National Fusion Research Institute, Daejeon 34133 (Korea, Republic of); Kang, Youngkil; Lim, Kisuk [SFA Engineering Corporation, Hwaseong-si, Gyeonggi-do 10060 (Korea, Republic of)

    2016-11-01

    Highlights: • Design improvement of the ITER Thermal Shields was introduced. • Design of TS manifold and TS instrumentation were summarized. • Produced main material of the TS (SS304LN) was summarized. • Status of the VVTS manufacturing and the inspection requirements were summarized. - Abstract: The role of the ITER Thermal Shields (TS) is to minimize the radiation heat load from the warm components such as vacuum vessel and cryostat to magnet operating at 4.5 K. The final design of TS was completed in 2013 and manufacturing of the vacuum vessel thermal shield (VVTS) is now on-going. This paper describes the development status of the TS in particular the design improvements, the fabrication and the requirements.

  10. Electromagnetic Shielding Efficiency Measurement of Composite Materials

    Science.gov (United States)

    Dřínovský, J.; Kejík, Z.

    2009-01-01

    This paper deals with the theoretical and practical aspects of the shielding efficiency measurements of construction composite materials. This contribution describes an alternative test method of these measurements by using the measurement circular flange. The measured results and parameters of coaxial test flange are also discussed. The measurement circular flange is described by measured scattering parameters in the frequency range from 9 kHz up to 1 GHz. The accuracy of the used shielding efficiency measurement method was checked by brass calibration ring. The suitability of the coaxial test setup was also checked by measurements on the EMC test chamber. This data was compared with the measured data on the real EMC chamber. The whole measurement of shielding efficiency was controlled by the program which runs on a personal computer. This program was created in the VEE Pro environment produced by © Agilent Technology.

  11. Radiation shielding performance of some concrete

    International Nuclear Information System (INIS)

    Akkurt, I.; Akyildirim, H.; Mavi, B.; Kilincarslan, S.; Basyigit, C.

    2007-01-01

    The energy consumption is increasing with the increased population of the world and thus new energy sources were discovered such as nuclear energy. Besides using nuclear energy, nuclear techniques are being used in a variety of fields such as medical hospital, industry, agriculture or military issue, the radiation protection becomes one of the important research fields. In radiation protection, the main rules are time, distance and shielding. The most effective radiation shields are materials which have a high density and high atomic number such as lead, tungsten which are expensive. Alternatively the concrete which produced using different aggregate can be used. The effectiveness of radiation shielding is frequently described in terms of the half value layer (HVL) or the tenth value layer (TVL). These are the thicknesses of an absorber that will reduce the radiation to half, and one tenth of its intensity respectively. In this study the radiation protection properties of different types of concrete will be discussed

  12. Accelerator shielding experts meet at CERN

    CERN Multimedia

    CERN Bulletin

    2010-01-01

    Fifteen years after its first CERN edition, the Shielding Aspects of Accelerator, Targets and Irradiation Facility (SATIF) conference was held again here from 2-4 June. Now at its 10th edition, SATIF10 brought together experts from all over the world to discuss issues related to the shielding techniques. They set out the scene for an improved collaboration and discussed novel shielding solutions.   This was the most attended meeting of the series with more than 65 participants from 34 institutions and 14 countries. “We welcomed experts from many different laboratories around the world. We come from different contexts but we face similar problems. In this year’s session, among other things, we discussed ways for improving the effectiveness of calculations versus real data, as well as experimental solutions to investigate the damage that radiation produces on various materials and the electronics”, says Marco Silari, Chair of the conference and member of the DGS/RP gro...

  13. Heating profiles on ICRF antenna Faraday shields

    International Nuclear Information System (INIS)

    Taylor, D.J.; Baity, F.W.; Hahs, C.L.; Riemer, B.W.; Ryan, P.M.; Williamson, D.E.

    1991-01-01

    A conceptual design for an uncooled Faraday shield for the BPX ion cyclotron resonance heating (ICRH) antenna, which should withstand the proposed long-pulse operation, has been completed. A high-heat-flux, uncooled Faraday shield has also been designed for the fast-wave current drive (FWCD) antenna on D3-D. For both components, the improved understanding of the heating profiles made it possible to design for heat fluxes that would otherwise have been too close to mechanically established limits. The analytical effort is described in detail, with emphasis on the design work for the BPX ICRH antenna conceptual design and for the replacement Faraday shield for the D3-D FWCD antenna. Results of analyses are shown, and configuration issues involved in component modeling are discussed. 3 refs., 6 figs., 2 tabs

  14. First Wall, Blanket, Shield Engineering Technology Program

    International Nuclear Information System (INIS)

    Nygren, R.E.

    1982-01-01

    The First Wall/Blanket/Shield Engineering Technology Program sponsored by the Office of Fusion Energy of DOE has the overall objective of providing engineering data that will define performance parameters for nuclear systems in advanced fusion reactors. The program comprises testing and the development of computational tools in four areas: (1) thermomechanical and thermal-hydraulic performance of first-wall component facsimiles with emphasis on surface heat loads; (2) thermomechanical and thermal-hydraulic performance of blanket and shield component facsimiles with emphasis on bulk heating; (3) electromagnetic effects in first wall, blanket, and shield component facsimiles with emphasis on transient field penetration and eddy-current effects; (4) assembly, maintenance and repair with emphasis on remote-handling techniques. This paper will focus on elements 2 and 4 above and, in keeping with the conference participation from both fusion and fission programs, will emphasize potential interfaces between fusion technology and experience in the fission industry

  15. Measuring the CO2 shadow price for wastewater treatment: A directional distance function approach

    International Nuclear Information System (INIS)

    Molinos-Senante, María; Hanley, Nick; Sala-Garrido, Ramón

    2015-01-01

    Highlights: • The shadow price of CO 2 informs about the marginal abatement cost of this pollutant. • It is estimated the shadow price of CO 2 for wastewater treatment plants. • The shadow prices depend on the setting of the directional vectors of the distance function. • Sewage sludge treatment technology affects the CO 2 shadow price. - Abstract: The estimation of the value of carbon emissions has become a major research and policy topic since the establishment of the Kyoto Protocol. The shadow price of CO 2 provides information about the marginal abatement cost of this pollutant. It is an essential element in guiding environmental policy issues, since the CO 2 shadow price can be used when fixing carbon tax rates, in environmental cost-benefit analysis and in ascertaining an initial market price for a trading system. The water industry could play an important role in the reduction of greenhouse gas (GHG) emissions. This paper estimates the shadow price of CO 2 for a sample of wastewater treatment plants (WWTPs), using a parametric quadratic directional distance function. Following this, in a sensitivity analysis, the paper evaluates the impact of different settings of directional vectors on the shadow prices. Applying the Mann–Whitney and Kruskal–Wallis non-parametric tests, factors affecting CO 2 prices are investigated. The variation of CO 2 shadow prices across the WWTPs evaluated argues in favour of a market-based approach to CO 2 mitigation as opposed to command-and-control regulation. The paper argues that the estimation of the shadow price of CO 2 for non-power enterprises can provide incentives for reducing GHG emissions

  16. Fabrication of high-aspect-ratio nano structures using a nano x-ray shadow mask

    International Nuclear Information System (INIS)

    Kim, Yong Chul; Lee, Seung S

    2008-01-01

    This paper describes a novel method for the fabrication of high-aspect-ratio nano structures (HAR-nano structures) using a nano x-ray shadow mask and deep x-ray lithography (DXRL). The nano x-ray shadow mask is fabricated by depositing an x-ray absorber layer (Au, 3 µm) onto the back side of a nano shadow mask. The nano shadow mask is produced with nano-sized apertures whose dimensions are reduced to several tens of nanometers by the accumulation of low-stress silicon nitride (Si x N y ) using the LPCVD process on the shadow mask. A shadow mask containing apertures with a size of 1 µm is fabricated on a bulk micromachined Si x N y membrane. The thickness of an absorber layer must be in the range of several tens of micrometers in order to obtain a contrast of more than 100 for the conventional DXRL process at the Pohang Light Source (PLS). However, a 3 µm thick absorber layer can provide a sufficient contrast if the modified DXRL of the central beam-stop method is used, which blocks high-energy x-rays. A nano shadow mask with 30 nm sized apertures is fabricated and a nano x-ray shadow mask with 250 nm sized apertures is fabricated by depositing a 3 µm thick absorber layer on a nano shadow mask with 500 nm sized apertures. HAR-nano structures (circles with a diameter of 420 nm and lines with a width of 274 nm) with aspect ratios of over 10:1 on a 3.2 µm SU-8 are successfully fabricated by using the nano x-ray shadow mask and the central beam-stop method

  17. Perception of object motion in three-dimensional space induced by cast shadows.

    Science.gov (United States)

    Katsuyama, Narumi; Usui, Nobuo; Nose, Izuru; Taira, Masato

    2011-01-01

    Cast shadows can be salient depth cues in three-dimensional (3D) vision. Using a motion illusion in which a ball is perceived to roll in depth on the bottom or to flow in the front plane depending on the slope of the trajectory of its cast shadow, we investigated cortical mechanisms underlying 3D vision based on cast shadows using fMRI techniques. When modified versions of the original illusion, in which the slope of the shadow trajectory (shadow slope) was changed in 5 steps from the same one as the ball trajectory to the horizontal, were presented to participants, their perceived ball trajectory shifted gradually from rolling on the bottom to floating in the front plane as the change of the shadow slope. This observation suggests that the perception of the ball trajectory in this illusion is strongly affected by the motion of the cast shadow. In the fMRI study, cortical activity during observation of the movies of the illusion was investigated. We found that the bilateral posterior-occipital sulcus (POS) and right ventral precuneus showed activation related to the perception of the ball trajectory induced by the cast shadows in the illusion. Of these areas, it was suggested that the right POS may be involved in the inferring of the ball trajectory by the given spatial relation between the ball and the shadow. Our present results suggest that the posterior portion of the medial parietal cortex may be involved in 3D vision by cast shadows. Copyright © 2010 Elsevier Inc. All rights reserved.

  18. Design of Reflective, Photonic Shields for Atmospheric Reentry

    Science.gov (United States)

    Komarevskiy, Nikolay; Shklover, Valery; Braginsky, Leonid; Hafner, Christian; Fabrichnaya, Olga; White, Susan; Lawson, John

    2010-01-01

    We present the design of one-dimensional photonic crystal structures, which can be used as omnidirectional reflecting shields against radiative heating of space vehicles entering the Earth's atmosphere. This radiation is approximated by two broad bands centered at visible and near-infrared energies. We applied two approaches to find structures with the best omnidirectional reflecting performance. The first approach is based on a band gap analysis and leads to structures composed of stacked Bragg mirrors. In the second approach, we optimize the structure using an evolutionary strategy. The suggested structures are compared with a simple design of two stacked Bragg mirrors. Choice of the constituent materials for the layers as well as the influence of interlayer diffusion at high temperatures are discussed.

  19. Design of a prototype D-D neutron generator and shielding calcuation

    International Nuclear Information System (INIS)

    Kim, I. J.; Kim, S. H.; Choi, H. D.

    2003-01-01

    The design concept of the D-D neutron generator, being developed in Seoul National University, is summarized and the development procedure of the prototype device is described. The designing goal of the neutron generator is; neutron yield 10 8 n/s, D + ion beam current 50 mA, acceleration voltage 120 kV. The detail of the prototype device, aiming at ion beam current 10 mA, acceleration voltage 30 kV, neutron yield 10 4 n/s, is being designed now. In addition, the simple calculation and MCNP simulation, for the radiation shielding against the neutron and ν-ray emitted from the neutron generator, was done on simple geometric condition and the quantitative criterion for the radiation shielding design was established

  20. Self-Shielding Of Transmission Lines

    Energy Technology Data Exchange (ETDEWEB)

    Christodoulou, Christos [Univ. of New Mexico, Albuquerque, NM (United States)

    2017-03-01

    The use of shielding to contend with noise or harmful EMI/EMR energy is not a new concept. An inevitable trade that must be made for shielding is physical space and weight. Space was often not as much of a painful design trade in older larger systems as they are in today’s smaller systems. Today we are packing in an exponentially growing number of functionality within the same or smaller volumes. As systems become smaller and space within systems become more restricted, the implementation of shielding becomes more problematic. Often, space that was used to design a more mechanically robust component must be used for shielding. As the system gets smaller and space is at more of a premium, the trades starts to result in defects, designs with inadequate margin in other performance areas, and designs that are sensitive to manufacturing variability. With these challenges in mind, it would be ideal to maximize attenuation of harmful fields as they inevitably couple onto transmission lines without the use of traditional shielding. Dr. Tom Van Doren proposed a design concept for transmission lines to a class of engineers while visiting New Mexico. This design concept works by maximizing Electric field (E) and Magnetic Field (H) field containment between operating transmission lines to achieve what he called “Self-Shielding”. By making the geometric centroid of the outgoing current coincident with the return current, maximum field containment is achieved. The reciprocal should be true as well, resulting in greater attenuation of incident fields. Figure’s 1(a)-1(b) are examples of designs where the current centroids are coincident. Coax cables are good examples of transmission lines with co-located centroids but they demonstrate excellent field attenuation for other reasons and can’t be used to test this design concept. Figure 1(b) is a flex circuit design that demonstrate the implementation of self-shielding vs a standard conductor layout.

  1. A study on the shielding element using Monte Carlo simulation

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Ki Jeong [Dept. of Radiology, Konkuk University Medical Center, Seoul (Korea, Republic of); Shim, Jae Goo [Dept. of Radiologic Technology, Daegu Health College, Daegu (Korea, Republic of)

    2017-06-15

    In this research, we simulated the elementary star shielding ability using Monte Carlo simulation to apply medical radiation shielding sheet which can replace existing lead. In the selection of elements, mainly elements and metal elements having a large atomic number, which are known to have high shielding performance, recently, various composite materials have improved shielding performance, so that weight reduction, processability, In consideration of activity etc., 21 elements were selected. The simulation tools were utilized Monte Carlo method. As a result of simulating the shielding performance by each element, it was estimated that the shielding ratio is the highest at 98.82% and 98.44% for tungsten and gold.

  2. Lightweight engine containment. [Kevlar shielding

    Science.gov (United States)

    Weaver, A. T.

    1977-01-01

    Kevlar fabric styles and weaves were studied, as well as methods of application for advanced gas turbine engines. The Kevlar material was subjected to high speed impacts by simple projectiles fired from a rifle, as well as more complex shapes such as fan blades released from gas turbine rotors in a spin pit. Just contained data was developed for a variety of weave and/or application techniques, and a comparative containment weight efficiency was established for Kevlar containment applications. The data generated during these tests is being incorporated into an analytical design system so that blade containment trade-off studies between Kevlar and metal case engine structures can be made. Laboratory tests and engine environment tests were performed to determine the survivability of Kevlar in a gas turbine environment.

  3. FLUKA shielding calculations for the FAIR project

    International Nuclear Information System (INIS)

    Fehrenbacher, Georg; Kozlova, Ekaterina; Radon, Torsten; Sokolov, Alexey

    2015-01-01

    FAIR is an international accelerator project being in construction at GSI Helmholtz center for heavy ion research in Darmstadt. The Monte Carlo program FLUKA is used to study radiation protection problems. The contribution deals with general application possibilities of FLUKA and for FAIR with respect the radiation protection planning. The necessity to simulate the radiation transport through shielding of several meters thickness and to determine the equivalent doses outside the shielding with sufficient accuracy is demonstrated using two examples under consideration of the variance reduction. Results of simulation calculations for activation estimation in accelerator facilities are presented.

  4. Thermophysical Properties of Heat Resistant Shielding Material

    International Nuclear Information System (INIS)

    Porter, W.D.

    2004-01-01

    This project was aimed at determining thermal conductivity, specific heat and thermal expansion of a heat resistant shielding material for neutron absorption applications. These data are critical in predicting the structural integrity of the shielding under thermal cycling and mechanical load. The measurements of thermal conductivity and specific heat were conducted in air at five different temperatures (-31 F, 73.4 F, 140 F, 212 F and 302 F). The transient plane source (TPS) method was used in the tests. Thermal expansion tests were conducted using push rod dilatometry over the continuous range from -40 F (-40 C) to 302 F (150 C)

  5. [Electromagnetic Shielding Alters Behaviour of Rats].

    Science.gov (United States)

    Temuryants, N A; Kostyuk, A S; Tumanyants, K N

    2015-01-01

    It has been found that long-term electromagnetic shielding (19 hours per day for 10 days) leads to an increase in the duration of passive swimming time in male rats, decrease the duration of active swimming in the "forced swim" test as well as decrease of libido. On the other hand animals kept under the "open field" conditions do not show significant deviations from their normal behavior. Therefore, one could conclude that moderate electromagnetic shielding causes a depression-like state in rats.

  6. Radiation shielding issues on the FMIT

    International Nuclear Information System (INIS)

    Burke, R.J.; Davis, A.A.; Huang, S.; Morford, R.J.

    1981-05-01

    The Fusion Materials Irradiation Test Facility (FMIT) is being built to study neutron radiation effects in candidate fusion reactor materials. The FMIT will yield high fluence data in a fusion-like neutron radiation environment produced by the interaction of a 0.1A, 35 MeV deuteron beam with a flowing lithium target. The design of the facility as a whole is driven by a high availability requirement. The variety of radiation environments in the facility requires the use of diverse and extensive shielding. Shielding design throughout the FMIT must accommodate the need for maintenance and operations access while providing adequate personnel and equipment protection

  7. WASTE HANDLING BUILDING SHIELD WALL ANALYSIS

    Energy Technology Data Exchange (ETDEWEB)

    D. Padula

    2000-01-13

    The scope of this analysis is to estimate the shielding wall, ceiling or equivalent door thicknesses that will be required in the Waste Handling Building to maintain the radiation doses to personnel within acceptable limits. The shielding thickness calculated is the minimum required to meet administrative limits, and not necessarily what will be recommended for the final design. The preliminary evaluations will identify the areas which have the greatest impact on mechanical and facility design concepts. The objective is to provide the design teams with the necessary information to assure an efficient and effective design.

  8. LOFT shield tank steady state temperatures with addition of gamma and neutron shielding

    International Nuclear Information System (INIS)

    Kyllingstad, G.

    1977-01-01

    The effect of introducing a neutron and gamma shield into the annulus between the reactor vessel and the shield tank is analyzed. This addition has been proposed in order to intercept neutron streaming up the annulus during nuclear operations. Its installation will require removal of approximately 20- 1 / 2 inches of stainless steel foil insulation at the top of the annulus. The resulting conduction path is believed to result in increased water temperatures within the shield tank, possibly beyond the 150 0 F limit, and/or cooling of the reactor vessel nozzles such that adverse thermal stresses would be generated. A two dimensional thermal analysis using the finite element code COUPLE/MOD2 was done for the shield tank system illustrated in the figure (1). The reactor was assumed to be at full power, 55 MW (th), with a loop flow rate of 2.15 x 10 6 lbm/hr (268.4 kg/s) at 2250 psi (15.51 MPa). Calculations indicate a steady state shield tank water temperature of 140 0 F (60 0 C). This is below the 150 0 F (65.56 0 C) limit. Also, no significant changes in thermal gradients within the nozzle or reactor vessel wall are generated. A spacer between the gamma shield and the shield tank is recommended, however, in order to ensure free air circulation through the annulus

  9. Poloidal asymmetries in the limiter shadow plasma of the Alcator C tokamak. Volume 1

    International Nuclear Information System (INIS)

    LaBombard, B.

    1986-05-01

    This thesis investigates conditions which exist in the limiter shadow plasma of the Alcator C tokamak. The understanding of this edge plasma region is approached from both experimental and theoretical points of view. First, a general overview of edge plasma physical processes is presented. Simple edge plasma models and conditions which can theoretically result in a poloidally asymmetric edge plasma are discussed. A review of data obtained from previous diagnostics in the Alcator C edge plasma is then used to motivate the development of a new edge plasma diagnostic system (DENSEPACK) to experimentally investigate poloidal asymmetries in this region. The bulk of this thesis focuses on the marked poloidal asymmetries detected by this poloidal probe array and possible mechanisms which might support such asymmetries on a magnetic flux surface. In processing the probe data, some important considerations on fitting Langmuir probe characteristics are identified. The remainder of this thesis catalogues edge versus central plasma parameter dependences. Regression analysis techniques are applied to characterize edge density for various central plasma parameters. Edge plasma conditions during lower hybrid radio frequency heating and pellet injection are also discussed

  10. Shadow-cone-enhanced secondary-ion mass-spectrometry studies of Ag/110/

    International Nuclear Information System (INIS)

    Chang; Winograd, N.

    1989-01-01

    The yield of particles ejected due to keV ion bombardment of Ag/110/ has been observed to depend strongly on the angle of incidence of the primary ion beam. The desorption angles of these particles are found to reflect both the crystallographic and chemical structure of the surface. Molecular dynamics calculations indicate that the desorption yield of all particles is significantly enhanced when the shadow cone of the incident beam of particles created by a surface atom intersects adjacent surface atoms. These angles may be accurately calculated by use of a full three-dimensional trajectory calculation of the scattering or by simple computation of the angle of this intersection using a two-body Moliere interaction potential function. With this approach it is possible to assign all of the angular anisotropies observed from secondary ions ejected from Ag/110/. Moreover, a detailed analysis suggests that the topmost atomic layer is relaxed inward by (7.8 +- 2.5)% and that the spacing between the first and third layer is contracted by (4.1 +- 2.1)% relative to the bulk spacings. These results are in excellent agreement with recent Rutherford backscattering experiments. A number of new possible applications of this technique to the analysis of chemisorbed overlayers is also discussed

  11. Rainforest metropolis casts 1,000-km defaunation shadow.

    Science.gov (United States)

    Tregidgo, Daniel J; Barlow, Jos; Pompeu, Paulo S; de Almeida Rocha, Mayana; Parry, Luke

    2017-08-08

    Tropical rainforest regions are urbanizing rapidly, yet the role of emerging metropolises in driving wildlife overharvesting in forests and inland waters is unknown. We present evidence of a large defaunation shadow around a rainforest metropolis. Using interviews with 392 rural fishers, we show that fishing has severely depleted a large-bodied keystone fish species, tambaqui ( Colossoma macropomum ), with an impact extending over 1,000 km from the rainforest city of Manaus (population 2.1 million). There was strong evidence of defaunation within this area, including a 50% reduction in body size and catch rate (catch per unit effort). Our findings link these declines to city-based boats that provide rural fishers with reliable access to fish buyers and ice and likely impact rural fisher livelihoods and flooded forest biodiversity. This empirical evidence that urban markets can defaunate deep into rainforest wilderness has implications for other urbanizing socioecological systems.

  12. Quarkonium plus prompt-photon associated hadroproduction and nuclear shadowing

    Energy Technology Data Exchange (ETDEWEB)

    Brenner Mariotto, C. [Universidade Federal do Rio Grande, Instituto de Matematica, Estatistica e Fisica, Caixa Postal 474, Rio Grande, RS (Brazil); Machado, M.V.T. [Universidade Federal do Pampa Campus de Bage, Centro de Ciencias Exatas e Tecnologicas, Bage, RS (Brazil)

    2010-06-15

    Quarkonium hadroproduction in association with a photon at high energies provides a probe of the dynamics of the strong interactions as it is dependent on the nuclear gluon distribution. Therefore, it could be used to constrain the behavior of the nuclear gluon distribution in proton-nucleus and nucleus-nucleus collisions. Such processes are useful to single out the magnitude of the shadowing/antishadowing effects in the nuclear parton densities. In this work we investigate the influence of nuclear effects in the production of J/{psi}+{gamma} and {upsilon}+{gamma} and estimate the transverse momentum dependence of the nuclear modification factors. The theoretical framework considered in the J/{psi} ({upsilon}) production associated with a direct photon at the hadron collider is the non-relativistic QCD (NRQCD) factorization formalism. (orig.)

  13. The Shadow of Big Data: Data-Citizenship and Exclusion

    DEFF Research Database (Denmark)

    Rossi, Luca; Hjelholt, Morten; Neumayer, Christina

    2016-01-01

    The shadow of Big Data: data-citizenship and exclusion Big data are understood as being able to provide insights on human behaviour at an individual as well as at an aggregated societal level (Manyka et al. 2011). These insights are expected to be more detailed and precise than anything before...... thanks to the large volume of digital data and to the unobstrusive nature of the data collection (Fishleigh 2014). Within this perspective, these two dimensions (volume and unobstrusiveness) define contemporary big data techniques as a socio-technical offering to society, a live representation of itself...... this process "data-citizenship" emerges. Data-citizenship assumes that citizens will be visible to the state through the data they produce. On a general level data-citizenship shifts citizenship from an intrinsic status of a group of people to a status achieved through action. This approach assumes equal...

  14. AN ANALYSIS OF THE SHADOW ECONOMY IN EU COUNTRIES

    Directory of Open Access Journals (Sweden)

    Brindusa Mihaela Tudose

    2016-08-01

    Full Text Available The paper aims at analysing the dimension of the underground economy in the EU states between 2003 and 2015. In order to achieve this goal, we use qualitative and quantitative methods. In the first two sections of the study we resort to conceptualisation and bring up to date scientific contributions in the field of the shadow economy both in terms of its definition and the methods of quantifying the phenomenon. In the third section, based on the results of the latest research, we identify the dynamics of the underground economy on three levels: the EU-15 (before and after 2005; the EU-10 (before and after the accession of 10 countries in 2005 and the EU-3 (before and after 2007. The main conclusion is that regardless of the reporting level (national, European, world, the real size of the underground economy remains unknown.

  15. Rainforest metropolis casts 1,000-km defaunation shadow

    Science.gov (United States)

    Tregidgo, Daniel J.; Barlow, Jos; Pompeu, Paulo S.; de Almeida Rocha, Mayana; Parry, Luke

    2017-01-01

    Tropical rainforest regions are urbanizing rapidly, yet the role of emerging metropolises in driving wildlife overharvesting in forests and inland waters is unknown. We present evidence of a large defaunation shadow around a rainforest metropolis. Using interviews with 392 rural fishers, we show that fishing has severely depleted a large-bodied keystone fish species, tambaqui (Colossoma macropomum), with an impact extending over 1,000 km from the rainforest city of Manaus (population 2.1 million). There was strong evidence of defaunation within this area, including a 50% reduction in body size and catch rate (catch per unit effort). Our findings link these declines to city-based boats that provide rural fishers with reliable access to fish buyers and ice and likely impact rural fisher livelihoods and flooded forest biodiversity. This empirical evidence that urban markets can defaunate deep into rainforest wilderness has implications for other urbanizing socioecological systems. PMID:28739913

  16. Extending the Predictability of Rain Shadow Effects Using Spatial Analogs

    Science.gov (United States)

    Frediani, M. E.; Stull, R.

    2017-12-01

    The goal of this study is to improve forecasts of precipitation and cloudiness over southwest British Columbia, Canada. We investigate the predictability of a Rain Shadow Effect (RSE), characterized by atmospheric states in which the downstream precipitation and associated cloud mass are suppressed as a consequence of flow interaction with orography. When upstream low-level flow is perpendicular to the steep terrain over Vancouver Island, downsloping winds and mountain waves develop over the Strait of Georgia. This condition favors a RSE, characterized by cloudiness and precipitation surrounding the metropolitan Vancouver. The RSE is given by a nonlinear relationship between the atmospheric flow and topography. Consequently, to forecast the RSE, NWP models must correctly predict low-level atmospheric flows, and must accurately represent the region's complex topography. Forecasting the RSE over Vancouver is specifically challenging because of the lack of low-level observations over the eastern Pacific in the so-called Pacific Data Void. The sparse upstream observation network weakens forecast skill normally obtained from data assimilation, and prohibits thorough model verification. Consequently, the atmospheric profile associated with the RSE remains unknown. In this study, analog forecasts are created with a similarity measure based on spatial flow patterns obtained from infrared satellite channels. RSE occurrences are identified using radar reflectivity observations, and the corresponding mesoscale spatial pattern from satellite imagery provide the 2-D flow portrait to search for analogous patterns. This analysis will indicate whether spatial similarities in water vapor and cloudiness flows may be used to detect predictive features and inform probabilities of developing rain shadows over the metropolitan Vancouver region.

  17. An experimental study of pressure shadows in partially molten rocks

    Science.gov (United States)

    Qi, Chao; Zhao, Yong-Hong; Kohlstedt, David L.

    2013-11-01

    As a two-phase, solid-melt material flows around rigid particles, melt-depleted and melt-enriched regions (i.e., pressure shadows) develop due to the coupled fluxes of melt and solid driven by pressure gradients around the particles. To study this compaction-decompaction process, samples composed of fine-grained San Carlos olivine plus mid-ocean ridge basalt containing dispersed sub-millimeter-sized, single crystal beads of olivine were deformed in torsion at a temperature of 1473 K and a confining pressure of 300 MPa. Indicated by melt distribution maps obtained from reflected-light optical and backscattered electron microscopy, melt-enriched and melt-depleted regions around the beads became observable at a local shear strain of γ≈1 in samples with an initially homogeneously distributed melt fraction of ϕ≈0.05. The melt-enriched regions (ϕbarhigh≈0.06 to 0.10) and the melt-depleted regions (ϕbarlow≈0.02 to 0.04), extending as far as one radius of the bead, were symmetrically distributed around the bead. The flow field of the olivine matrix determined from crystallographic preferred orientations agrees with theoretical predictions based on two-phase flow analysis. These experiments are the first to produce pressure shadows in partially molten rocks. One implication of this study is that it will be possible to constrain the ratio of bulk to shear viscosity, which is inferred from the distribution of melt using a combination of experimental observations and numerical simulations.

  18. Detection and tracking of moving objects under occlusion and shadow

    Science.gov (United States)

    Ming, Ying; Jiang, Jingjue

    2005-10-01

    This paper presents a system to detect and track multiple moving objects in the presence of mutual occlusion and shadow. A novel change detection algorithm based on Cauchy distribution is proposed. The ratio of pixel's intensities between two images is used as the feature to model and subtract background. The distribution of the ratio of background pixel's intensities between a current image and a reference image can obeys Cauchy distribution, assumed that some observed temporal intensity variation of each pixel in a background image is caused by white noise. By hypothesis testing whose decision thresholds are related to the false alarm rate, robust change detection can be carried out. We exploit spectral and geometrical properties of shadows to recognize and eliminate them in video sequences. Intensity, hue and saturation in the YCbCr color space is employed to this end. In order to solve ambiguity due to occlusion and recover from intermittent tracking failure, we propose a method to implement tracking of multiple moving objects. The method is based on multi-cue and dynamic templates matching in consecutive frames and motion estimation by Kalman filter. In our system, a fast accurate clustering algorithm based on k-nearest neighbor search is employed and the feature space is constructed by extracting the position, color, shape and velocity information of moving objects. In this paper, occlusions are addressed in two classes, i.e. static occlusion and dynamic occlusion. Depend on the prior knowledge of the background scene and the feedback from objects detection and tracking, the distribution of static occlusion region in the scene can be acquired and updated. The bounding box around a static occlusion region is used as an alarm sign to start the process of static occlusion. Dynamic occlusion event can be detected and processed in terms of the proposed tracking scheme and multi-cue and dynamic templates matching approach. Experiment results demonstrate that the

  19. Improvement of system of corporate management organs by forming shadow board

    Directory of Open Access Journals (Sweden)

    V.P. Holiver

    2017-08-01

    Full Text Available The article determines that the current existing system of corporate management organs of ajoint-stock company needs improvement in the direction of preparation of labour reserve. The expediency of forming labour reserve by board of directors in the joint-stock company is considered by the improvement of the system of corporate management organs and forming in its composition an alternative organ called a shadow board. The article determines that the activity of board of directors is carried out on the basis of conservative strategy, which consists of a careful conduct at the acceptance of administrative decisions. It is set that the activity of bord of directors is conservative from dependence on shareholders who appoint them. The paper proves the efficiency of combination of conservative strategy of making decision suggested by the board of directors with the aggressive strategy of the alternative organ, which must be the prototype of board of directors, but it must operate within the limits of aggressive strategy. It is proved that the synergy of conservative and aggressive strategy of forming suggestions by the board of directors of the joint-stock company with the use of additional working organ (shadow board will bring an effect. The effect from such synergy is the upgrading of making decisions by the board of directors. The place of shadow board in the system of corporate management organs is outlined. The analogy of shadow board’s activity similar to the activity of board of directors of the joint-stock company is shown. The features of co-operation of board of directors and shadow board are marked. The features of forming committees as a part of a shadow board and a general committee with a board of directors are outlined. The article deals with the key role of the shadow board in the preparation of skilled reserve of board of directors of the joint-stock company and in providing more aggressive strategy for making decisions. The

  20. Magnetic shielding of an inhomogeneous magnetic field source by a bulk superconducting tube

    International Nuclear Information System (INIS)

    Hogan, K; Fagnard, J-F; Wéra, L; Vanderheyden, B; Vanderbemden, P

    2015-01-01

    Bulk type-II irreversible superconductors can act as excellent passive magnetic shields, with a strong attenuation of low frequency magnetic fields. Up to now, the performances of superconducting magnetic shields have mainly been studied in a homogenous magnetic field, considering only immunity problems, i.e. when the field is applied outside the tube and the inner field should ideally be zero. In this paper, we aim to investigate experimentally and numerically the magnetic response of a high-T c bulk superconducting hollow cylinder at 77 K in an emission problem, i.e. when subjected to the non-uniform magnetic field generated by a source coil placed inside the tube. A bespoke 3D mapping system coupled with a three-axis Hall probe is used to measure the magnetic flux density distribution outside the superconducting magnetic shield. A finite element model is developed to understand how the magnetic field penetrates into the superconductor and how the induced superconducting shielding currents flow inside the shield in the case where the emitting coil is placed coaxially inside the tube. The finite element modelling is found to be in excellent agreement with the experimental data. Results show that a concentration of the magnetic flux lines occurs between the emitting coil and the superconducting screen. This effect is observed both with the modelling and the experiment. In the case of a long tube, we show that the main features of the field penetration in the superconducting walls can be reproduced with a simple analytical 1D model. This model is used to estimate the maximum flux density of the emitting coil that can be shielded by the superconductor. (paper)

  1. A simple model for the nuclear unintegrated gluon distribution

    Energy Technology Data Exchange (ETDEWEB)

    Betemps, M.A. [Universidade Federal de Pelotas, Conjunto Agrotecnico Visconde da Graca, CAVG, Pelotas, RS (Brazil); Machado, M.V.T. [Universidade Federal do Pampa, Centro de Ciencias Exatas e Tecnologicas, Bage, RS (Brazil)

    2010-02-15

    The solution of non-linear evolution equations for dense nuclear gluon density has been suggested as one of the relevant mechanisms of pA and AA collisions at collider energies. Here we study a simple parameterization for the unintegrated gluon distribution using the knowledge of asymptotic solutions of the Balitsky-Kovchegov equation, describing high-energy QCD in the presence of saturation effects. A satisfactory description of nuclear shadowing at small x is obtained and it allows us to understand the qualitative behavior shown by the data. (orig.)

  2. Effects of shielding the radiosensitive superficial organs of ORNL pediatric phantoms on dose reduction in computed tomography.

    Science.gov (United States)

    Akhlaghi, Parisa; Miri-Hakimabad, Hashem; Rafat-Motavalli, Laleh

    2014-10-01

    In computed tomography (CT), some superficial organs which have increased sensitivity to radiation, receive doses that are significant enough to be matter of concern. Therefore, in this study, the effects of using shields on the amount of dose reduction and image quality was investigated for pediatric imaging. Absorbed doses of breasts, eyes, thyroid and testes of a series of pediatric phantoms without and with different thickness of bismuth and lead were calculated by Monte Carlo simulation. Appropriate thicknesses of shields were chosen based on their weights, X-ray spectrum, and the amount of dose reduction. In addition, the effect of lead shield on image quality of a simple phantom was assessed quantitatively using region of interest (ROI) measurements. Considering the maximum reduction in absorbed doses and X-ray spectrum, using a lead shield with a maximum thickness of 0.4 mm would be appropriate for testes and thyroid and two other organs (which are exposed directly) should be protected with thinner shields. Moreover, the image quality assessment showed that lead was associated with significant increases in both noise and CT attenuation values, especially in the anterior of the phantom. Overall, the results suggested that shielding is a useful optimization tool in CT.

  3. Effects of shielding the radiosensitive superficial organs of ORNL pediatric phantoms on dose reduction in computed tomography

    Directory of Open Access Journals (Sweden)

    Parisa Akhlaghi

    2014-01-01

    Full Text Available In computed tomography (CT, some superficial organs which have increased sensitivity to radiation, receive doses that are significant enough to be matter of concern. Therefore, in this study, the effects of using shields on the amount of dose reduction and image quality was investigated for pediatric imaging. Absorbed doses of breasts, eyes, thyroid and testes of a series of pediatric phantoms without and with different thickness of bismuth and lead were calculated by Monte Carlo simulation. Appropriate thicknesses of shields were chosen based on their weights, X-ray spectrum, and the amount of dose reduction. In addition, the effect of lead shield on image quality of a simple phantom was assessed quantitatively using region of interest (ROI measurements. Considering the maximum reduction in absorbed doses and X-ray spectrum, using a lead shield with a maximum thickness of 0.4 mm would be appropriate for testes and thyroid and two other organs (which are exposed directly should be protected with thinner shields. Moreover, the image quality assessment showed that lead was associated with significant increases in both noise and CT attenuation values, especially in the anterior of the phantom. Overall, the results suggested that shielding is a useful optimization tool in CT.

  4. Frustum-Traced Irregular Z-Buffers: Fast, Sub-pixel Accurate Hard Shadows.

    Science.gov (United States)

    Wyman, Chris; Hoetzlein, Rama; Lefohn, Aaron

    2016-05-25

    We further describe and analyze a real-time system for rendering antialiased hard shadows using irregular z-buffers (IZBs) that we first presented in Wyman et al. [1]. We focus on identifying bottlenecks, exploring these from an algorithmic complexity standpoint, and presenting techniques to improve performance. Our system remains interactive on a variety of game assets and CAD models while running at resolutions 1920 1080 and above and imposes no constraints on light, camera or geometry, allowing fully dynamic scenes without precomputation. We render sub-pixel accurate, 32 sample per pixel hard shadows at roughly twice the cost of a single sample per pixel. This allows us to smoothly animate even subpixel shadows from grass or wires without introducing spatial or temporal aliasing. Prior algorithms for irregular z-buffer shadows rely heavily on the GPU's compute pipeline. Instead we leverage the standard rasterization-based graphics pipeline, including hardware conservative raster and early-z culling. Our key observation is noting a duality between irregular z-buffer performance and shadow map quality; irregular z-buffering is most costly exactly where shadow maps exhibit the worst aliasing. This allows us to use common shadow map algorithms, which typically improve aliasing, to instead reduce our cost. Compared to state of the art ray tracers, we spawn similar numbers of triangle intersections per pixel yet completely rebuild our data structure in under 1 ms per frame.

  5. An IMU-Aided Body-Shadowing Error Compensation Method for Indoor Bluetooth Positioning.

    Science.gov (United States)

    Deng, Zhongliang; Fu, Xiao; Wang, Hanhua

    2018-01-20

    Research on indoor positioning technologies has recently become a hotspot because of the huge social and economic potential of indoor location-based services (ILBS). Wireless positioning signals have a considerable attenuation in received signal strength (RSS) when transmitting through human bodies, which would cause significant ranging and positioning errors in RSS-based systems. This paper mainly focuses on the body-shadowing impairment of RSS-based ranging and positioning, and derives a mathematical expression of the relation between the body-shadowing effect and the positioning error. In addition, an inertial measurement unit-aided (IMU-aided) body-shadowing detection strategy is designed, and an error compensation model is established to mitigate the effect of body-shadowing. A Bluetooth positioning algorithm with body-shadowing error compensation (BP-BEC) is then proposed to improve both the positioning accuracy and the robustness in indoor body-shadowing environments. Experiments are conducted in two indoor test beds, and the performance of both the BP-BEC algorithm and the algorithms without body-shadowing error compensation (named no-BEC) is evaluated. The results show that the BP-BEC outperforms the no-BEC by about 60.1% and 73.6% in terms of positioning accuracy and robustness, respectively. Moreover, the execution time of the BP-BEC algorithm is also evaluated, and results show that the convergence speed of the proposed algorithm has an insignificant effect on real-time localization.

  6. An IMU-Aided Body-Shadowing Error Compensation Method for Indoor Bluetooth Positioning

    Directory of Open Access Journals (Sweden)

    Zhongliang Deng

    2018-01-01

    Full Text Available Research on indoor positioning technologies has recently become a hotspot because of the huge social and economic potential of indoor location-based services (ILBS. Wireless positioning signals have a considerable attenuation in received signal strength (RSS when transmitting through human bodies, which would cause significant ranging and positioning errors in RSS-based systems. This paper mainly focuses on the body-shadowing impairment of RSS-based ranging and positioning, and derives a mathematical expression of the relation between the body-shadowing effect and the positioning error. In addition, an inertial measurement unit-aided (IMU-aided body-shadowing detection strategy is designed, and an error compensation model is established to mitigate the effect of body-shadowing. A Bluetooth positioning algorithm with body-shadowing error compensation (BP-BEC is then proposed to improve both the positioning accuracy and the robustness in indoor body-shadowing environments. Experiments are conducted in two indoor test beds, and the performance of both the BP-BEC algorithm and the algorithms without body-shadowing error compensation (named no-BEC is evaluated. The results show that the BP-BEC outperforms the no-BEC by about 60.1% and 73.6% in terms of positioning accuracy and robustness, respectively. Moreover, the execution time of the BP-BEC algorithm is also evaluated, and results show that the convergence speed of the proposed algorithm has an insignificant effect on real-time localization.

  7. SHADOW EFFECT ON PHOTOVOLTAIC POTENTIALITY ANALYSIS USING 3D CITY MODELS

    Directory of Open Access Journals (Sweden)

    N. Alam

    2012-07-01

    Full Text Available Due to global warming, green-house effect and various other drawbacks of existing energy sources, renewable energy like Photovoltaic system is being popular for energy production. The result of photovoltaic potentiality analysis depends on data quality and parameters. Shadow rapidly decreases performance of the Photovoltaic system and it always changes due to the movement of the sun. Solar radiation incident on earth's atmosphere is relatively constant but the radiation at earth's surface varies due to absorption, scattering, reflection, change in spectral content, diffuse component, water vapor, clouds and pollution etc. In this research, it is being investigated that how efficiently real-time shadow can be detected for both direct and diffuse radiation considering reflection and other factors in contrast with the existing shadow detection methods using latest technologies and what is the minimum quality of data required for this purpose. Of course, geometric details of the building geometry and surroundings directly affect the calculation of shadows. In principle, 3D city models or point clouds, which contain roof structure, vegetation, thematically differentiated surface and texture, are suitable to simulate exact real-time shadow. This research would develop an automated procedure to measure exact shadow effect from the 3D city models and a long-term simulation model to determine the produced energy from the photovoltaic system. In this paper, a developed method for detecting shadow for direct radiation has been discussed with its result using a 3D city model to perform a solar energy potentiality analysis.

  8. Summary of Prometheus Radiation Shielding Nuclear Design Analysis

    Energy Technology Data Exchange (ETDEWEB)

    J. Stephens

    2006-01-13

    This report transmits a summary of radiation shielding nuclear design studies performed to support the Prometheus project. Together, the enclosures and references associated with this document describe NRPCT (KAPL & Bettis) shielding nuclear design analyses done for the project.

  9. Neutron shielding material based on colemanite and epoxy resin.

    Science.gov (United States)

    Okuno, Koichi

    2005-01-01

    In recent years, there has been a need for compact shielding design such as self-shielding of a PET cyclotron or upgradation of radiation machinery in existing facilities. In these cases, high performance shielding materials are needed. Concrete or polyethylene have been used for a neutron shield. However, for compact shielding, they fall short in terms of performance or durability. Therefore, a new type of neutron shielding material based on epoxy resin and colemanite has been developed. Slab attenuation experiments up to 40 cm for the new shielding material were carried out using a 252Cf neutron source. Measurement was carried out using a REM-counter, and compared with calculation. The results show that the shielding performance is better than concrete and polyethylene mixed with 10 wt% boron oxide. From the result, we confirmed that the performance of the new material is suitable for practical use.

  10. Early test facilities and analytic methods for radiation shielding: Proceedings

    International Nuclear Information System (INIS)

    Ingersoll, D.T.; Ingersoll, J.K.

    1992-11-01

    This report represents a compilation of eight papers presented at the 1992 American Nuclear Society/European Nuclear Society International Meeting. The meeting is of special significance since it commemorates the fiftieth anniversary of the first controlled nuclear chain reaction. The papers contained in this report were presented in a special session organized by the Radiation Protection and Shielding Division in keeping with the historical theme of the meeting. The paper titles are good indicators of their content and are: (1) The origin of radiation shielding research: The Oak Ridge experience, (2) Shielding research at the hanford site, (3) Aircraft shielding experiments at General Dynamics Fort Worth, 1950-1962, (4) Where have the neutrons gone?, a history of the tower shielding facility, (5) History and evolution of buildup factors, (6) Early shielding research at Bettis atomic power laboratory, (7) UK reactor shielding: then and now, (8) A very personal view of the development of radiation shielding theory

  11. Early test facilities and analytic methods for radiation shielding: Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Ingersoll, D T [comp.; Oak Ridge National Lab., TN (United States); Ingersoll, J K [comp.; Tec-Com, Knoxville, TN (United States)

    1992-11-01

    This report represents a compilation of eight papers presented at the 1992 American Nuclear Society/European Nuclear Society International Meeting. The meeting is of special significance since it commemorates the fiftieth anniversary of the first controlled nuclear chain reaction. The papers contained in this report were presented in a special session organized by the Radiation Protection and Shielding Division in keeping with the historical theme of the meeting. The paper titles are good indicators of their content and are: (1) The origin of radiation shielding research: The Oak Ridge experience, (2) Shielding research at the hanford site, (3) Aircraft shielding experiments at General Dynamics Fort Worth, 1950-1962, (4) Where have the neutrons gone , a history of the tower shielding facility, (5) History and evolution of buildup factors, (6) Early shielding research at Bettis atomic power laboratory, (7) UK reactor shielding: then and now, (8) A very personal view of the development of radiation shielding theory.

  12. A new ceramic material for shielding pulsed neutron scattering instruments

    International Nuclear Information System (INIS)

    Celli, M.; Grazzi, F.; Zoppi, M.

    2006-01-01

    We propose a new ceramic composite, based on boron carbide, to use as a shielding material for pulsed neutron scattering instrumentation. The measured transmission data show characteristics equivalent to crispy mix, a common shielding material used at ISIS (UK)

  13. Summary of Prometheus Radiation Shielding Nuclear Design Analyses , for information

    International Nuclear Information System (INIS)

    J. Stephens

    2006-01-01

    This report transmits a summary of radiation shielding nuclear design studies performed to support the Prometheus project. Together, the enclosures and references associated with this document describe NRPCT (KAPL and Bettis) shielding nuclear design analyses done for the project

  14. Software Tools for Measuring and Calculating Electromagnetic Shielding Effectiveness

    National Research Council Canada - National Science Library

    Tesny, Neal

    2005-01-01

    The evaluation and the analysis of high-altitude electromagnetic pulse response of shielded enclosures require the availability of software tools able to acquire data and calculate shielding effectiveness...

  15. Active Shielding in Measurements of DC Near Biomagnetic Fields

    National Research Council Canada - National Science Library

    Nowak, Hannes

    2001-01-01

    .... An effective SQUID based active shielding system has been developed and installed at the magnetically shielded rooms in the Biomagnetic Center of the University Jena to reduce external low frequency disturbances...

  16. The Tower Shielding Facility: Its glorious past

    Energy Technology Data Exchange (ETDEWEB)

    Muckenthaler, F.J.

    1997-05-07

    The Tower Shielding Facility (TSF) is the only reactor facility in the US that was designed and built for radiation-shielding studies in which both the reactor source and shield samples could be raised into the air to allow measurements to be made without interference from ground scattering or other spurious effects. The TSF proved its usefulness as many different programs were successfully completed. It became active in work for the Defense Atomic Support Agency (DASA) Space Nuclear Auxiliary Power, Defense Nuclear Agency, Liquid Metal Fast Breeder Reactor Program, the Gas-Cooled and High-Temperature Gas-Cooled Reactor programs, and the Japanese-American Shielding Program of Experimental Research, just to mention a few of the more extensive ones. The history of the TSF as presented in this report describes the various experiments that were performed using the different reactors. The experiments are categorized as to the programs which they supported and placed in corresponding chapters. The experiments are described in modest detail, along with their purpose when appropriate. Discussion of the results is minimal, but references are given to more extensive topical reports.

  17. Thermal testing of solid neutron shielding materials

    International Nuclear Information System (INIS)

    Boonstra, R.H.

    1993-01-01

    In May-June 1989 the first series of full-scale thermal tests was performed on three shielding materials: Bisco Products NS-4-FR, and Reactor Experiments RX-201 and RX-207. The tests are described in Thermal Testing of Solid Neutron Shielding Materials, GA-A19897, R.H. Boonstra, General Atomics (1990), and demonstrated the acceptability of these materials in a thermal accident. Subsequent design changes to the cask rendered these materials unattractive in terms of weight or adequate service temperature margin. For the second test series a material specification was developed for a polypropylene based neutron shield with a softening point of at least 280degF. Table 1 lists the neutron shield materials tested. The Envirotech and Bisco materials are not polypropylene, but were tested as potential backup materials in the event that a satisfactory polypropylene could not be found. The Bisco modified NS-4 and Reactor Experiments HMPP are both acceptable materials from a thermal accident standpoint for use in the shipping cask. Tests of the Kobe PP-R01 and Envirotech HDPE were stopped for safety reasons, due to inability to deal with the heavy smoke, before completion of the 30-minute heating phase. However these materials may prove satisfactory if they could undergo the complete heating. (J.P.N.)

  18. The Tower Shielding Facility: Its glorious past

    International Nuclear Information System (INIS)

    Muckenthaler, F.J.

    1997-01-01

    The Tower Shielding Facility (TSF) is the only reactor facility in the US that was designed and built for radiation-shielding studies in which both the reactor source and shield samples could be raised into the air to allow measurements to be made without interference from ground scattering or other spurious effects. The TSF proved its usefulness as many different programs were successfully completed. It became active in work for the Defense Atomic Support Agency (DASA) Space Nuclear Auxiliary Power, Defense Nuclear Agency, Liquid Metal Fast Breeder Reactor Program, the Gas-Cooled and High-Temperature Gas-Cooled Reactor programs, and the Japanese-American Shielding Program of Experimental Research, just to mention a few of the more extensive ones. The history of the TSF as presented in this report describes the various experiments that were performed using the different reactors. The experiments are categorized as to the programs which they supported and placed in corresponding chapters. The experiments are described in modest detail, along with their purpose when appropriate. Discussion of the results is minimal, but references are given to more extensive topical reports

  19. 40 CFR 72.51 - Permit shield.

    Science.gov (United States)

    2010-07-01

    ... REGULATION Acid Rain Permit Contents § 72.51 Permit shield. Each affected unit operated in accordance with the Acid Rain permit that governs the unit and that was issued in compliance with title IV of the Act, as provided in this part and parts 73, 74, 75, 76, 77, and 78 of this chapter shall be deemed to be...

  20. Development of ceramics multifunctional shielding materials

    Energy Technology Data Exchange (ETDEWEB)

    Senda, Tetsuya; Akiyama, Shigeru; Takahashi, Chiori; Matsuoka, Kazuyoshi; Uematsu, Susumu; Ueki, Kotaro; Ohashi, Atsuto; Naruyama, Nobuteru [Ship Research Inst., Tokyo (Japan)

    1999-02-01

    New aspect 'multifunctional shielding materials' with high temperature structure materials and shielding performance was proposed. The enhancement effects of shielding performance by combination of various ceramics were studied and the thermal impulse strength and surface damage-resistance were evaluated. In the case of combination of chromium carbide, titanium borate and boron nitride, the best shielding arrangement was proposed as chromium carbide with intermediate nucleus on the neutron beam source side and boron nitride, light element ceramics, on the other side and titanium borate between them. Each layer showed the special effects such as chromium carbide with the promotion effect of chromium, titanium borate to decrease neutron velocity and absorption and boron nitride to absorb neutron. The thermal shock characteristic value of chromium carbide was PL=3.3 W/mm{sup 2}, about 0.2 times of titanium borate, PL=16.5 W/mm{sup 2}. Accordingly, some thermal shock relaxation layer should be set, when chromium carbide was set on the beam source side. (S.Y.)

  1. MPACT Subgroup Self-Shielding Efficiency Improvements

    International Nuclear Information System (INIS)

    Stimpson, Shane; Liu, Yuxuan; Collins, Benjamin S.; Clarno, Kevin T.

    2016-01-01

    Recent developments to improve the efficiency of the MOC solvers in MPACT have yielded effective kernels that loop over several energy groups at once, rather that looping over one group at a time. These kernels have produced roughly a 2x speedup on the MOC sweeping time during eigenvalue calculation. However, the self-shielding subgroup calculation had not been reevaluated to take advantage of these new kernels, which typically requires substantial solve time. The improvements covered in this report start by integrating the multigroup kernel concepts into the subgroup calculation, which are then used as the basis for further extensions. The next improvement that is covered is what is currently being termed as ''Lumped Parameter MOC''. Because the subgroup calculation is a purely fixed source problem and multiple sweeps are performed only to update the boundary angular fluxes, the sweep procedure can be condensed to allow for the instantaneous propagation of the flux across a spatial domain, without the need to sweep along all segments in a ray. Once the boundary angular fluxes are considered to be converged, an additional sweep that will tally the scalar flux is completed. The last improvement that is investigated is the possible reduction of the number of azimuthal angles per octant in the shielding sweep. Typically 16 azimuthal angles per octant are used for self-shielding and eigenvalue calculations, but it is possible that the self-shielding sweeps are less sensitive to the number of angles than the full eigenvalue calculation.

  2. Subsurface Shielding Source Term Specification Calculation

    International Nuclear Information System (INIS)

    S.Su

    2001-01-01

    The purpose of this calculation is to establish appropriate and defensible waste-package radiation source terms for use in repository subsurface shielding design. This calculation supports the shielding design for the waste emplacement and retrieval system, and subsurface facility system. The objective is to identify the limiting waste package and specify its associated source terms including source strengths and energy spectra. Consistent with the Technical Work Plan for Subsurface Design Section FY 01 Work Activities (CRWMS M and O 2001, p. 15), the scope of work includes the following: (1) Review source terms generated by the Waste Package Department (WPD) for various waste forms and waste package types, and compile them for shielding-specific applications. (2) Determine acceptable waste package specific source terms for use in subsurface shielding design, using a reasonable and defensible methodology that is not unduly conservative. This calculation is associated with the engineering and design activity for the waste emplacement and retrieval system, and subsurface facility system. The technical work plan for this calculation is provided in CRWMS M and O 2001. Development and performance of this calculation conforms to the procedure, AP-3.12Q, Calculations

  3. In-beam background suppression shield

    DEFF Research Database (Denmark)

    Santoro, V.; Cai, Xiao Xiao; DiJulio, D. D.

    2015-01-01

    , which do not use a bender to help mitigate the fast neutron background, are the most challenging. For these beam lines we propose the innovative shielding of placing blocks of material directly into the guide system, which allow a minimum attenuation of the cold and thermal fluxes relative...

  4. Internally shielded beam transport and support system

    International Nuclear Information System (INIS)

    Schildkamp, W.; Brewer, H.

    1996-01-01

    Due to environmental concerns, the Advanced Photon Source has a policy that disallows any exposed lead within the facility. This creates a real problem for the beam transport system, not so much for the pipe but for the flexible coupling (bellows) sections. A complete internally shielded x-ray transport system, consisting of long transport lines joined by flexible coupling sections, has been designed for CARS sector 14 to operate either at high vacuum or as a helium flight tube. It can effectively shield against air scattering of wiggler or undulator white beam with proper placement of apertures, collimators, and masks for direct beam control. The system makes use of male- and female-style fittings that create a labyrinth allowing for continuous shielding through the flexible coupling sections. These parts are precision machined from a ternary hypereutectic lead alloy (cast under 15 inches of head pressure to assure a pinhole-free casting) then pressed into either end (rotatable vacuum flanges) of the bellows assembly. The transport pipe itself consists of a four part construction using a stepped transition ring (Z-ring) to connect an inner tube to the vacuum flange and also to a protective and supportive outer tube. The inner tube is wrapped with 1/16 double-prime pure lead sheet to a predetermined thickness following the shape of the stepped transition ring for continuous shielding. This design has been prototyped and radiation tested. copyright 1996 American Institute of Physics

  5. Shielding Effectiveness Measurements using a Reverberation Chamber

    NARCIS (Netherlands)

    Leferink, Frank Bernardus Johannes; Bergsma, J.G.; Bergsma, Hans; van Etten, Wim

    2006-01-01

    Shielding effectiveness measurements have been performed using a reverberation chamber. The reverberation chamber methodology as we1l as the measurement setup is described and some results are given. Samples include glass reinforced plastic panels, aluminum panels with many holes, wire mesh, among

  6. AP1000 shield building: a constructability challenge

    International Nuclear Information System (INIS)

    Di Giuseppe, Giovanni; Bonanno, Domenico

    2010-01-01

    The AP1000 Shield Building, an enhanced structure which surrounds the containment vessel, consists of standard Reinforced Concrete (RC) and composite Steel and Concrete (SC) construction. In the SC module the surface steel plates, (with attached shear studs and angles) filled with concrete, act as the steel reinforcement in concrete. This is a relatively new design technology that required the appropriate use of structural codes, supplemented with information from applicable tests on similar composite steel and concrete construction. Being a newer design concept, existing codes do not provide explicit guidance on SC construction so a review of literature and test data on composite structures similar to AP1000 shield building was done in order to confirm the technical basis for the design. The SC walls, air inlet structure and roof of the Shield Building will be constructed using modular construction practices and then transported to site and lifted into place. These modules, working also as permanent form-work, will be filled with high strength Self- Consolidating Concrete. (SCC) This paper provides a focused and integrated presentation of the enhanced shield building design methodology, testing, constructability and inspection. (authors)

  7. Estimate of the shielding effect on secondary cancer risk due to cone-beam CT in image-guided radiotherapy

    Energy Technology Data Exchange (ETDEWEB)

    Sung, Jiwon; Baek, Taeseong; Yoon, Myonggeun [Korea University, Seoul (Korea, Republic of); Kim, Dongwook; Kim, Donghyun [Kyung Hee University Hospital at Gangdong, Seoul (Korea, Republic of)

    2014-09-15

    This study evaluated the effect of a simple shielding method using a thin lead sheet on the imaging dose caused by cone-beam computed tomography (CBCT) in image-guided radiation therapy (IGRT). Reduction of secondary doses from CBCT was measured using a radio-photoluminescence glass dosimeter (RPLGD) placed inside an anthropomorphic phantom. The entire body, except for the region scanned by using CBCT, was shielded by wrapping it with a 2-mm lead sheet. Changes in secondary cancer risk due to shielding were calculated using BEIR VII models. Doses to out-of-field organs for head-and-neck, chest, and pelvis scans were decreased 15 ∼ 100%, 23 ∼ 90%, and 23 ∼ 98%, respectively, and the average reductions in lifetime secondary cancer risk due to the 2-mm lead shielding were 1.6, 11.5, and 12.7 persons per 100,000, respectively. These findings suggest that a simple, thin-lead-sheet-based shielding method can effectively decrease secondary doses to out-of-field regions for CBCT, which reduces the lifetime cancer risk on average by 9 per 100,000 patients.

  8. Multihelix rotating shield brachytherapy for cervical cancer

    Energy Technology Data Exchange (ETDEWEB)

    Dadkhah, Hossein [Department of Biomedical Engineering, University of Iowa, 1402 Seamans Center for the Engineering Arts and Sciences, Iowa City, Iowa 52242 (United States); Kim, Yusung; Flynn, Ryan T., E-mail: ryan-flynn@uiowa.edu [Department of Radiation Oncology, University of Iowa, 200 Hawkins Drive, Iowa City, Iowa 52242 (United States); Wu, Xiaodong [Department of Radiation Oncology, University of Iowa, 200 Hawkins Drive, Iowa City, Iowa 52242 and Department of Electrical and Computer Engineering, University of Iowa, 4016 Seamans Center for the Engineering Arts and Sciences, Iowa City, Iowa 52242 (United States)

    2015-11-15

    Purpose: To present a novel brachytherapy technique, called multihelix rotating shield brachytherapy (H-RSBT), for the precise angular and linear positioning of a partial shield in a curved applicator. H-RSBT mechanically enables the dose delivery using only linear translational motion of the radiation source/shield combination. The previously proposed approach of serial rotating shield brachytherapy (S-RSBT), in which the partial shield is rotated to several angular positions at each source dwell position [W. Yang et al., “Rotating-shield brachytherapy for cervical cancer,” Phys. Med. Biol. 58, 3931–3941 (2013)], is mechanically challenging to implement in a curved applicator, and H-RSBT is proposed as a feasible solution. Methods: A Henschke-type applicator, designed for an electronic brachytherapy source (Xoft Axxent™) and a 0.5 mm thick tungsten partial shield with 180° or 45° azimuthal emission angles and 116° asymmetric zenith angle, is proposed. The interior wall of the applicator contains six evenly spaced helical keyways that rigidly define the emission direction of the partial radiation shield as a function of depth in the applicator. The shield contains three uniformly distributed protruding keys on its exterior wall and is attached to the source such that it rotates freely, thus longitudinal translational motion of the source is transferred to rotational motion of the shield. S-RSBT and H-RSBT treatment plans with 180° and 45° azimuthal emission angles were generated for five cervical cancer patients with a diverse range of high-risk target volume (HR-CTV) shapes and applicator positions. For each patient, the total number of emission angles was held nearly constant for S-RSBT and H-RSBT by using dwell positions separated by 5 and 1.7 mm, respectively, and emission directions separated by 22.5° and 60°, respectively. Treatment delivery time and tumor coverage (D{sub 90} of HR-CTV) were the two metrics used as the basis for evaluation and

  9. Proceedings of a meeting on radiation shielding and related topics

    International Nuclear Information System (INIS)

    1978-01-01

    This is a proceedings of a meeting on radiation shielding and related topics held on Feb. 22 and 23 in 1978 at Nuclear Engineering Research Laboratory of University of Tokyo. The reports includes the following items (1) studies on neutronics with accelerators (2) radiation damage (3) shielding design (4) radiation streaming (5) shielding experiments from a point of view of radiation measurements (6) shielding benchmark experiments (7) prospects on the study of neutronics. All items are written in Japanese. (auth.)

  10. Shielding consideration for the SSCL experimental halls

    International Nuclear Information System (INIS)

    Bull, J.; Coyne, J.; Mokhov, N.; Stapleton, G.

    1994-03-01

    The Superconducting Super Collider which is being designed and built in Waxahachie, Texas consists Of series of proton accelerators, culminating in a 20 Te proton on proton collider. The collider will be in a tunnel which will be 87 km in circumference and. on average about 30 meters underground. The present design calls for two large interaction halls on the east side of the ring. The shielding for these halls is being designed for an interaction rate of 10 9 Hz or 10 16 interactions per year, based on 10 7 seconds per operational year. SSC guidelines require that the shielding be designed to meet the criterion of 1mSv per year for open areas off site 2mSv per year for open areas on site, and 2mSv per year for controlled areas. Only radiation workers will be routinely allowed to work in controlled areas. It should be pointed that there is a potential for an accidental full beam loss in either of the experimental halls, and this event would consist of the loss of the full circulating beam up to 4 x 10 14 protons. With the present design. the calculated dose equivalent for this event is about 10% of the annual dose equivalent for the normal p-p interactions, so that die accident condition does not control the shielding. If, for instance, local shielding within the experimental hall is introduced into the calculations, this could change. The shielding requirements presented here are controlled by the normal p-p interactions. Three important questions were addressed in the present calculations. They are (1) the thickness of the roof over the experimental halls, (2) the configuration of the shafts and adits which give access to the halls, and (3) the problem of ground water and air activation

  11. Flux trapping and shielding in irreversible superconductors

    International Nuclear Information System (INIS)

    Frankel, D.J.

    1978-05-01

    Flux trappings and shielding experiments were carried out on Pb, Nb, Pb-Bi, Nb-Sn, and Nb-Ti samples of various shapes. Movable Hall probes were used to measure fields near or inside the samples as a function of position and of applied field. The trapping of transverse multipole magnetic fields in tubular samples was accomplished by cooling the samples in an applied field and then smoothly reducing the applied field to zero. Transverse quadrupole and sextupole fields with gradients of over 2000 G/cm were trapped with typical fidelity to the original impressed field of a few percent. Transverse dipole fields of up to 17 kG were also trapped with similar fidelity. Shielding experiments were carried out by cooling the samples in zero field and then gradually applying an external field. Flux trapping and shielding abilities were found to be limited by two factors, the pinning strength of the material, and the susceptibility of a sample to flux jumping. The trapping and shielding behavior of flat disk samples in axial fields and thin-walled tubular samples in transverse fields was modeled. The models, which were based on the concept of the critical state, allowed a connection to be made between the pinning strength and critical current level, and the flux trapping and shielding abilities. Adiabatic and dynamic stability theories are discussed and applied to the materials tested. Good qualitative, but limited quantitative agreement was obtained between the predictions of the theoretical stability criteria and the observed flux jumping behavior

  12. Radiation shielding calculations for the vista spacecraft

    International Nuclear Information System (INIS)

    Sahin, Suemer; Sahin, Haci Mehmet; Acir, Adem

    2005-01-01

    The VISTA spacecraft design concept has been proposed for manned or heavy cargo deep space missions beyond earth orbit with inertial fusion energy propulsion. Rocket propulsion is provided by fusion power deposited in the inertial confined fuel pellet debris and with the help of a magnetic nozzle. The calculations for the radiation shielding have been revised under the fact that the highest jet efficiency of the vehicle could be attained only if the propelling plasma would have a narrow temperature distribution. The shield mass could be reduced from 600 tons in the original design to 62 tons. Natural and enriched lithium were the principle shielding materials. The allowable nuclear heating in the superconducting magnet coils (up to 5 mW/cm 3 ) is taken as the crucial criterion for dimensioning the radiation shielding structure of the spacecraft. The space craft mass is 6000 tons. Total peak nuclear power density in the coils is calculated as ∼5.0 mW/cm 3 for a fusion power output of 17 500 MW. The peak neutron heating density is ∼2.0 mW/cm 3 , and the peak γ-ray heating density is ∼3.0 mW/cm 3 (on different points) using natural lithium in the shielding. However, the volume averaged heat generation in the coils is much lower, namely 0.21, 0.71 and 0.92 mW/cm 3 for the neutron, γ-ray and total nuclear heating, respectively. The coil heating will be slightly lower if highly enriched 6 Li (90%) is used instead of natural lithium. Peak values are then calculated as 2.05, 2.15 and 4.2 mW/cm 3 for the neutron, γ-ray and total nuclear heating, respectively. The corresponding volume averaged heat generation in the coils became 0.19, 0.58 and 0.77 mW/cm 3

  13. Generalization of dependence between shadow radiation image and intensity of pulses at scanning detector output

    International Nuclear Information System (INIS)

    Nedavnij, O.I.; Udod, V.A.

    2000-01-01

    Dependence of general character is determined between shadow radiation image in nondestructive testing and intensity of electric pulse occasional flux observed at the detector output of testing radiometric system. Model for radiometric system detector operation in counting regime of radiation detection is derived. The model simultaneously accounts: possibility of scanning shadow radiation image of tested object (TO) by unspecified raster, possibility of using detectors with nonuniform spatial radiation sensitivity, effect of shadow radiation TO image averaging by detector in two-dimensional variant. This fact permits to investigate the maximum potential capabilities of radiation testing radiometric systems [ru

  14. Use of Shadowing-Based Learning in an Allied Health Microbiology Course

    Directory of Open Access Journals (Sweden)

    Alex A. Lowrey

    2016-05-01

    Full Text Available Students in an undergraduate microbiology course for health professions majors perform a shadowing-based learning exercise for their course project. Students accomplish this by shadowing a health care professional of their choice, specifically incorporating basic microbiological concept themes into their observations. These concept themes include the biological nature, health effects, detection, and control of microorganisms. Upon completion of the shadowing experience, students present a concise report, which is graded on how well the students connect course scientific concepts with actual clinical practice.

  15. A trial of selective imaging for the breast mass shadow by computed radiography

    International Nuclear Information System (INIS)

    Muramatsu, Yukio; Anan, Mitsuhiro; Tanaka, Takashi; Matsue, Hiroto; Yamada, Tatsuya

    1990-01-01

    CR has ability to make many kinds of images by several imaging processings. Especially, gradation processing is more important than frequency processing to make images in CR mammography. We developed new method to image breast masses selectively with new gradation processing and tried it for 18 patients over sixty years old with breast cancer. All of breast mass shadows were separated selectively from other parencymal shadow. So, we conclude that the auto-recognition of breast mass shadow can be possible in near future in CR system. (author)

  16. Shapes and Positions of Black Hole Shadows in Accretion Disks and Spin Parameters of Black Holes

    OpenAIRE

    Takahashi, Rohta

    2004-01-01

    Can we determine a spin parameter of a black hole by observation of a black hole shadow in an accretion disk? In order to answer this question, we make a qualitative analysis and a quantitative analysis of a shape and a position of a black hole shadow casted by a rotating black hole on an optically thick accretion disk and its dependence on an angular momentum of a black hole. We have found black hole shadows with a quite similar size and a shape for largely different black hole spin paramete...

  17. Cold Nuclear Matter effects on J/psi production at RHIC: comparing shadowing models

    Energy Technology Data Exchange (ETDEWEB)

    Ferreiro, E.G.; /Santiago de Compostela U.; Fleuret, F.; /Ecole Polytechnique; Lansberg, J.P.; /SLAC; Rakotozafindrabe, A.; /SPhN, DAPNIA, Saclay

    2009-06-19

    We present a wide study on the comparison of different shadowing models and their influence on J/{psi} production. We have taken into account the possibility of different partonic processes for the c{bar c}-pair production. We notice that the effect of shadowing corrections on J/{psi} production clearly depends on the partonic process considered. Our results are compared to the available data on dAu collisions at RHIC energies. We try different break up cross section for each of the studied shadowing models.

  18. 30 CFR 56.14213 - Ventilation and shielding for welding.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Ventilation and shielding for welding. 56.14213... Equipment Safety Practices and Operational Procedures § 56.14213 Ventilation and shielding for welding. (a) Welding operations shall be shielded when performed at locations where arc flash could be hazardous to...

  19. Spherical warm shield design for infrared imaging systems

    Science.gov (United States)

    Tian, Qijie; Chang, Songtao; He, Fengyun; Li, Zhou; Qiao, Yanfeng

    2017-09-01

    The F-number matching is the primary means to suppress stray radiation for infrared imaging systems. However, it is difficult to achieve exact F-number matching, owing to the restriction from detectors, or multiple F-number design. Hence, an additional shield is required to block the certain thermal radiation. Typical shield is called flat warm shield, which is flat and operates at room temperature. For flat warm shield, it cannot suppress stray radiation while achieving F-number matching. To overcome the restriction, a spherical reflective warm shield is required. First of all, the detailed theory of spherical warm shield design is developed on basis of the principle that stray radiation cannot directly reach the infrared focal plane array. According to the theory developed above, a polished spherical warm shield, whose radius is 18 mm, is designed to match an F/2 infrared detector with an F/4 infrared imaging system. Then, the performance and alignment errors of the designed spherical warm shield are analyzed by simulation. Finally, a contrast experiment between the designed spherical warm shield and two differently processed flat warm shields is performed in a chamber with controllable inside temperatures. The experimental results indicate that the designed spherical warm shield cannot only achieve F-number matching but suppress stray radiation sufficiently. Besides, it is demonstrated that the theory of spherical warm shield design developed in this paper is valid and can be employed by arbitrary infrared imaging systems.

  20. Advanced materials and design for electromagnetic interference shielding

    CERN Document Server

    Tong, Xingcun Colin

    2008-01-01

    Exploring the role of EMI shielding in EMC design, this book introduces the design guidelines, materials selection, characterization methodology, manufacturing technology, and future potential of EMI shielding. It covers an array of issues in advanced shielding materials and design solutions, including enclosures and composites.