Pegasus project. DLC coating and low viscosity oil reduce energy losses significantly

Energy Technology Data Exchange (ETDEWEB)

Doerwald, Dave; Jacobs, Ruud [Hauzer Techno Coating (Netherlands). Tribological Coatings

2012-03-15

Pegasus, the flying horse from Greek mythology, is a suitable name for the research project initiated by a German automotive OEM with participation of Hauzer Techno Coating and several automotive suppliers. It will enable future automotive vehicles to reduce fuel consumption without losing power. The project described in this article focuses on the rear differential, because reducing friction here can contribute considerably to efficiency improvement of the whole vehicle. Surfaces, coating and oil viscosity have been investigated and interesting conclusions have been reached. (orig.)

Reducing CO2 emissions and energy consumption of heat-integrated distillation systems.

Science.gov (United States)

Gadalla, Mamdouh A; Olujic, Zarko; Jansens, Peter J; Jobson, Megan; Smith, Robin

2005-09-01

Distillation systems are energy and power intensive processes and contribute significantly to the greenhouse gases emissions (e.g. carbon dioxide). Reducing CO2 emissions is an absolute necessity and expensive challenge to the chemical process industries in orderto meetthe environmental targets as agreed in the Kyoto Protocol. A simple model for the calculation of CO2 emissions from heat-integrated distillation systems is introduced, considering typical process industry utility devices such as boilers, furnaces, and turbines. Furnaces and turbines consume large quantities of fuels to provide electricity and process heats. As a result, they produce considerable amounts of CO2 gas to the atmosphere. Boilers are necessary to supply steam for heating purposes; besides, they are also significant emissions contributors. The model is used in an optimization-based approach to optimize the process conditions of an existing crude oil atmospheric tower in order to reduce its CO2 emissions and energy demands. It is also applied to generate design options to reduce the emissions from a novel internally heat-integrated distillation column (HIDiC). A gas turbine can be integrated with these distillation systems for larger emissions reduction and further energy savings. Results show that existing crude oil installations can save up to 21% in energy and 22% in emissions, when the process conditions are optimized. Additionally, by integrating a gas turbine, the total emissions can be reduced further by 48%. Internal heat-integrated columns can be a good alternative to conventional heat pump and other energy intensive close boiling mixtures separations. Energy savings can reach up to 100% with respect to reboiler heat requirements. Emissions of these configurations are cut down by up to 83%, compared to conventional units, and by 36%, with respect to heat pump alternatives. Importantly, cost savings and more profit are gained in parallel to emissions minimization.

All about size? – The potential of downsizing in reducing energy demand

International Nuclear Information System (INIS)

Huebner, Gesche M.; Shipworth, David

2017-01-01

Highlights: • Building size has huge impact on residential energy consumption. • There is significant underoccupation in English homes, even in cities. • Huge energy savings are possible if people downsize (move into smaller homes). • Lack of alternative, smaller accommodation structural barrier to downsizing. - Abstract: Residential energy consumption is one of the main contributors to CO_2 emissions in the UK. One strategy aimed at reducing emissions is to increase retrofitting rates of buildings. In this paper, an alternative approach is discussed and its potential impact on energy use assessed, that of downsizing (moving to smaller homes). Reviews of previous research show that a wide range of what can be termed psychological barriers exist to downsizing, such as the loss of ownership and independence, concern about what to do with possessions, not having enough space for visitors, and attachment to one’s home. Benefits of downsizing from a personal perspective are economic, with lower bills and/or rent, release of capital, lower maintenance costs, and also potential lifestyle improvements including living in easier-to-maintain and more age-appropriate housing. Wider societal benefits include the potential to significantly reduce energy consumption, and mitigating the housing crisis in cities where not enough properties are available. Empirical analysis on a nationally representative sample in England showed that building size alone accounts for 24% of the variability in energy consumption (compared to 11% of household size). If single-person households with more than two bedrooms downsized by one bedroom, energy-savings of 8% could be achieved, and if single-person households occupied only one bedroom, savings of 27%. Data also showed a significant amount of underoccupation, with almost two-thirds of households having more bedrooms than considered necessary compared to the bedroom-standard. However, analysis also revealed a structural barrier to

Comparison of three methods to reduce energy density: effects on daily energy intake

OpenAIRE

Williams, Rachel A.; Roe, Liane S.; Rolls, Barbara J.

2013-01-01

Reductions in food energy density can decrease energy intake, but it is not known if the effects depend on the way that energy density is reduced. We investigated whether three methods of reducing energy density (decreasing fat, increasing fruit and vegetables, and adding water) differed in their effects on energy intake across the day. In a crossover design, 59 adults ate breakfast, lunch, and dinner in the laboratory once a week for four weeks. Across conditions, the entrées were either sta...

Environment, Renewable Energy and Reduced Carbon Emissions

Science.gov (United States)

Sen, S.; Khazanov, G.; Kishimoto, Y.

2011-01-01

Increased energy security and reduced carbon emissions pose significant challenges for science and technology. However, they also create substantial opportunities for innovative research and development. In this review paper, we highlight some of the key opportunities and mention public policies that are needed to enable the efforts and to maximize the probability of their success. Climate is among the uttermost nonlinear behaviors found around us. As recent studies showed the possible effect of cosmic rays on the Earth's climate, we investigate how complex interactions between the planet and its environment can be responsible for climate anomalies.

The elastic strain energy of crystallographic shear planes in reduced tungsten trioxide

International Nuclear Information System (INIS)

Iguchi, E.; Tilley, R.J.D.

1977-01-01

Calculations of the elastic strain energy due to crystallographic shear (c.s.) planes lying upon 102, 103 and 001 planes in reduced tungsten trioxide crystals have been made. The cases analysed in detail are for both isolated c.s. planes and for pairs of c.s. planes. These results are used to determine the elastic strain energy per unit volume for crystals containing ordered arrays of c.s. planes. It was found that the magnitude of the elastic strain energy was in the sequence 001 < 102 < 103 and that at relatively small inter-c.s. spacings the curves of elastic strain energy against c.s. plane separation take the form of a series of peaks and valleys. These results are compared with experimental observations of c.s. plane spacings in substantially reduced crystals containing quasi-ordered arrays of c.s. planes and with observations of c.s. plane nucleation and growth in both slightly and more appreciably reduced crystals. It was found that the elastic strain energy plays a significant part in controlling the microstructure of c.s. plane arrays in such cases. (author)

Incorporation of air into a snack food reduces energy intake.

Science.gov (United States)

Osterholt, Kathrin M; Roe, Liane S; Rolls, Barbara J

2007-05-01

This study investigated how the air content of a familiar snack food affected energy intake and whether varying the method of serving the snack modified intake. We tested two versions of an extruded snack (cheese puffs) that were equal in energy density (5.7 kcal/g), but differed in energy per volume (less-aerated snack: 1.00 kcal/ml; more-aerated snack: 0.45 kcal/ml). In a within-subjects design, 16 women and 12 men consumed the snacks ad libitum in the laboratory during four afternoon sessions. A standard volume (1250 ml) of each snack was served once in a bowl and once in an opaque bag. Results showed significant differences in intake of the two snacks by energy (p=0.0003) and volume (psnack than the less-aerated snack, although they consumed a 73% greater volume of the more-aerated snack (239+/-24 ml). These findings suggest that subjects responded to both the weight and volume of the snack. Despite differences in intake, hunger and fullness ratings did not differ across conditions. The serving method did not significantly affect intake. Results from this study indicate that incorporating air into food provides a strategy to reduce energy intake from energy-dense snacks.

Energy activity guide : simple steps to reduce your household energy use

Energy Technology Data Exchange (ETDEWEB)

Byckalo-Khan, F; Wallace, C L [ed.

2003-07-01

This guide presents 13 practical activities that can help households reduce energy consumption in order to create a more sustainable lifestyle and to help meet Canada's Kyoto commitment to reduce greenhouse gas emissions. Most energy sources create pollution that harms both human health and the Earth. The burning of fossil fuels creates greenhouse gas emissions that contribute to climate change, smog, pollution and adverse health effects. This guide offers suggestions on how households can reduce the impact on the environment while saving money. Some of the initiatives include lowering the thermostat, replacing incandescent light bulbs with compact fluorescent light bulbs, turning off appliances when not in use, weatherising building envelopes, using a clothes line to dry clothes instead of a dryer, laundering clothes with cold water, and proper maintenance of heating equipment. An energy use chart is included with this guide to help track activities and to estimate how much time and money is required by each activity. refs., figs.

Energy activity guide : simple steps to reduce your household energy use

Energy Technology Data Exchange (ETDEWEB)

Byckalo-Khan, F.; Wallace, C.L. (ed.)

2003-07-01

This guide presents 13 practical activities that can help households reduce energy consumption in order to create a more sustainable lifestyle and to help meet Canada's Kyoto commitment to reduce greenhouse gas emissions. Most energy sources create pollution that harms both human health and the Earth. The burning of fossil fuels creates greenhouse gas emissions that contribute to climate change, smog, pollution and adverse health effects. This guide offers suggestions on how households can reduce the impact on the environment while saving money. Some of the initiatives include lowering the thermostat, replacing incandescent light bulbs with compact fluorescent light bulbs, turning off appliances when not in use, weatherising building envelopes, using a clothes line to dry clothes instead of a dryer, laundering clothes with cold water, and proper maintenance of heating equipment. An energy use chart is included with this guide to help track activities and to estimate how much time and money is required by each activity. refs., figs.

Device interactions in reducing the cost of tidal stream energy

International Nuclear Information System (INIS)

Vazquez, A.; Iglesias, G.

2015-01-01

Highlights: • Numerical modelling is used to estimate the levelised cost of tidal stream energy. • As a case study, a model of Lynmouth (UK) is implemented and successfully validated. • The resolution of the model allows the demarcation of individual devices on the model grid. • Device interactions reduce the available tidal resource and the cost increases significantly. - Abstract: The levelised cost of energy takes into account the lifetime generated energy and the costs associated with a project. The objective of this work is to investigate the effects of device interactions on the energy output and, therefore, on the levelised cost of energy of a tidal stream project, by means of numerical modelling. For this purpose, a case study is considered: Lynmouth (North Devon, UK), an area in the Bristol Channel in which the first tidal stream turbine was installed − a testimony of its potential as a tidal energy site. A state-of-the-art hydrodynamics model is implemented on a high-resolution computational grid, which allows the demarcation of the individual devices. The modification to the energy output resulting from interaction between turbines within the tidal farm is thus resolved for each individual turbine. The results indicate that significant changes in the levelised cost of energy values, of up to £0.221 kW h −1 , occur due to the aforementioned modifications, which should not be disregarded if the cost of tidal stream energy is to be minimised

Reducing carbon emissions through improved household energy efficiency in the UK

International Nuclear Information System (INIS)

Ekins, P.; Hargreaves, C.

2002-01-01

A number of schemes to increase household energy efficiency have operated in the UK over the last 5-10 years. This paper evaluates their effectiveness in terms of reducing household energy use, carbon emissions and fuel poverty. It then draws on the quantitative results of these schemes, and published plans for their continuation, to model an extended and expanded Household Energy Efficiency Scenario to 2020, using an integrated economy-energy-environment model of the UK. The results suggest that while such schemes can play a significant role in reducing carbon emissions from households, much more ambitious schemes than those currently implemented will be necessary to offset the underlying growth in these emissions. Finally, the results are compared with the UK government's own estimates, in its Climate Change Programme, of carbon emission reductions from such schemes to 2010. The paper concludes that the government's estimates are somewhat optimistic, and that it will need substantial new policy measures beyond those already announced if its carbon reduction targets in this area are to be met. (author)

Saving energy and reducing CO2 with electricity

International Nuclear Information System (INIS)

Yau, T.S.; Zaininger, H.W.

1991-10-01

Surprising potential exists for new and enhanced electric technologies to reduce energy use and CO 2 emission. Widespread deployment of these technologies could reduce energy use by up to 7 quads in 2010 and a corresponding reduction in carbon dioxide emission of up to 440 million tons. Electricity's unique high form value allows for efficiency at the point of end-use that is multiples of the efficiency possible in gas- or oil-fueled systems. The efficiency advantage at the point of end use more than offset the disadvantage of the high losses in the production of electricity. Hence, widespread deployment of many electric end uses will reduce the nation's total energy requirements. Major technologies which hold the greatest potential include electric process heating, industrial electrotechnologies, electric vehicles, information technologies that substitute electronic communication for transportation of people, and electric heat pumps for space heating, cooling and water heating. Wider use of these beneficial technologies in combination with the efficient use of electricity can reduce the nation's primary energy use and Co 2 emissions from electric generation by more than a quarter. 35 refs., 50 figs., 69 tabs

A systems approach to reduce urban rail energy consumption

International Nuclear Information System (INIS)

González-Gil, A.; Palacin, R.; Batty, P.; Powell, J.P.

2014-01-01

Highlights: • An insightful overview of energy usage in urban rail systems is given. • The principal measures to reduce urban rail energy consumption are appraised. • A methodology is proposed to help implement energy saving schemes in urban rail. • Regenerative braking is shown to offer the greatest energy saving potential. - Abstract: There is increasing interest in the potential of urban rail to reduce the impact of metropolitan transportation due to its high capacity, reliability and absence of local emissions. However, in a context characterised by increasing capacity demands and rising energy costs, and where other transport modes are considerably improving their environmental performance, urban rail must minimise its energy use without affecting its service quality. Urban rail energy consumption is defined by a wide range of interdependent factors; therefore, a system wide perspective is required, rather than focusing on energy savings at subsystem level. This paper contributes to the current literature by proposing an holistic approach to reduce the overall energy consumption of urban rail. Firstly, a general description of this transport mode is given, which includes an assessment of its typical energy breakdown. Secondly, a comprehensive appraisal of the main practices, strategies and technologies currently available to minimise its energy use is provided. These comprise: regenerative braking, energy-efficient driving, traction losses reduction, comfort functions optimisation, energy metering, smart power management and renewable energy micro-generation. Finally, a clear, logical methodology is described to optimally define and implement energy saving schemes in urban rail systems. This includes general guidelines for a qualitative assessment and comparison of measures alongside a discussion on the principal interdependences between them. As a hypothetical example of application, the paper concludes that the energy consumption in existing urban

Reduced energy conservation law for magnetized plasma

International Nuclear Information System (INIS)

Sosenko, P.P.; Decyk, V.K.

1994-01-01

A global energy conservation law for a magnetized plasma is studied within the context of a quasiparticle description. A reduced energy conservation law is derived for low-frequency, as compared to the gyromagnetic frequency, plasma motions with regard to both non-uniform mean flows and fluctuations in the plasma. The mean value of plasma energy is calculated and sufficient stability conditions for non-equilibrium plasmas are derived. (orig.)

Using REDUCE in high energy physics

International Nuclear Information System (INIS)

Grozin, A.G.

1997-01-01

This book describes the use of the symbolic manipulation language REDUCE in particle physics. There are several general purpose mathematics packages available to physicists, including Mathematica, Maple, and REDUCE. Each has advantages and disadvantages, but REDUCE has been found to be both powerful and convenient in solving a wide range of problems. This book introduces the reader to REDUCE and demonstrates its utility as a mathematical tool in physics. The first chapter of the book describes the REDUCE system, including some library packages. The following chapters show the use of REDUCE in examples from classical mechanics, hydrodynamics, general relativity, and quantum mechanics. The rest of the book systematically presents the Standard Model of particle physics (QED, weak interactions, QCD). A large number of scattering and decay processes are calculated with REDUCE. All example programs from the book can be downloaded via Internet. The emphasis throughout is on learning through worked examples. This will be an essential introduction and reference for high energy and theoretical physicists. (author)

Hidden vegetables: an effective strategy to reduce energy intake and increase vegetable intake in adults.

Science.gov (United States)

Blatt, Alexandria D; Roe, Liane S; Rolls, Barbara J

2011-04-01

The overconsumption of energy-dense foods leads to excessive energy intakes. The substitution of low-energy-dense vegetables for foods higher in energy density can help decrease energy intakes but may be difficult to implement if individuals dislike the taste of vegetables. We investigated whether incorporating puréed vegetables to decrease the energy density of entrées at multiple meals reduced daily energy intakes and increased daily vegetable intakes. In this crossover study, 20 men and 21 women ate ad libitum breakfast, lunch, and dinner in the laboratory once a week for 3 wk. Across conditions, entrées at meals varied in energy density from standard versions (100% condition) to reduced versions (85% and 75% conditions) by the covert incorporation of 3 or 4.5 times the amount of puréed vegetables. Entrées were accompanied by unmanipulated side dishes. Participants rated their hunger and fullness before and after meals. Subjects consumed a consistent weight of foods across conditions of energy density; thus, the daily energy intake significantly decreased by 202 ± 60 kcal in the 85% condition (P kcal in the 75% condition (P Daily vegetable consumption significantly increased from 270 ± 17 g of vegetables in the 100% condition to 487 ± 25 g of vegetables in the 75% condition (P < 0.0001). Despite the decreased energy intake, ratings of hunger and fullness did not significantly differ across conditions. Entrées were rated as similar in palatability across conditions. Large amounts of puréed vegetables can be incorporated into various foods to decrease the energy density. This strategy can lead to substantial reductions in energy intakes and increases in vegetable intakes. This trial was registered at clinicaltrials.gov as NCT01165086.

Acute oral administration of lauric acid reduces energy intake in healthy male

DEFF Research Database (Denmark)

Feltrin, K. L.; Brennan, I.M.; Rades, Thomas

2014-01-01

12 would result in a dose-related suppression of appetite and subsequent energy intake at breakfast and lunch. Methods 14 healthy men were studied on four separate occasions in double-blind, randomised fashion. Following ingestion of C12 (2 g (77 kJ), 4 g (153 kJ), or 6 g (230 kJ)) or control, energy...... intake at breakfast (30 min after C12 ingestion), perceptions of appetite, nausea and bloating (for 180 min following breakfast), and energy intake at lunch (180 min after breakfast), were measured. Results C12 ingestion did not induce nausea or bloating. While there was no effect of C12 on energy intake...... at breakfast, energy intake at lunch was reduced significantly after ingestion of both C12(2 g) (by 13.7%, P

Spring-like Ankle Foot Orthoses reduce the energy cost of walking by taking over ankle work.

Science.gov (United States)

Bregman, D J J; Harlaar, J; Meskers, C G M; de Groot, V

2012-01-01

In patients with central neurological disorders, gait is often limited by a reduced ability to push off with the ankle. To overcome this reduced ankle push-off, energy-storing, spring-like carbon-composite Ankle Foot Orthoses (AFO) can be prescribed. It is expected that the energy returned by the AFO in late stance will support ankle push-off, and reduce the energy cost of walking. In 10 patients with multiple sclerosis and stroke the energy cost of walking, 3D kinematics, joint power, and joint work were measured during gait, with and without the AFO. The mechanical characteristics of the AFO were measured separately, and used to calculate the contribution of the AFO to the ankle kinetics. We found a significant decrease of 9.8% in energy cost of walking when walking with the AFO. With the AFO, the range of motion of the ankle was reduced by 12.3°, and the net work around the ankle was reduced by 29%. The total net work in the affected leg remained unchanged. The AFO accounted for 60% of the positive ankle work, which reduced the total amount of work performed by the leg by 11.1% when walking with the AFO. The decrease in energy cost when walking with a spring-like energy-storing AFO in central neurological patients is not induced by an augmented net ankle push-off, but by the AFO partially taking over ankle work. Copyright © 2011 Elsevier B.V. All rights reserved.

Polaron interaction energies in reduced tungsten trioxide

International Nuclear Information System (INIS)

Iguchi, E.; Salje, E.; Tilley, R.J.D.

1981-01-01

Consideration of the properties of reduced tungsten trioxide suggest that the mobile charge carriers are polarons. As it is uncertain how the presence of polarons will influence the microstructures of the crystallographic shear (CS) planes present in reduced tungsten trioxide we have calculated both the polaron-CS plane and polaron-polaron interaction energy for a variety of circumstances. Three CS plane geometries were considered, (102), (103), and (001) CS plane arrays, and the nominal compositions of the crystals ranged from WO 2 70 to WO 3 0 . The polarons were assumed to have radii from 0.6 to 1.0 nm and the polaron-CS plane electrostatic interaction was assumed to be screened. The results suggest that for the most part the total interaction energy is small and is unlikely to be of major importance in controlling the microstructures found in CS planes. However, at very high polaron densities the interaction energy could be appreciable and may have some influence on the existence range of CS phases

Effect of exercise and dietary restraint on energy intake of reduced-obese women.

Science.gov (United States)

Keim, N L; Canty, D J; Barbieri, T F; Wu, M M

1996-02-01

Self-selected food intake of 15 reduced-obese women living in a metabolic ward was studied for 14 consecutive days to determine the effect of exercise and other metabolic and behavioral variables on energy intake. A choice of prepared food items were offered at breakfast, lunch and dinner, and a variety of additional food items were available continuously 24 h/day. Subjects performed either moderate intensity aerobic exercise (A-EX) (n = 8) expending 354 +/- 76 kcal/session or low intensity resistance weight training (R-EX)(n =7) expending 96 +/- kcal/session, 5 days/week. Mean energy intakes (kcal/day, +/- SEM) of the exercise groups were similar: 1867 +/- 275 for A-EX, 1889 +/- 294 for R-EX. Mean energy intakes of individuals ranged from 49 to 157% of the predetermined level required for weight maintenance. Resting metabolic rate per kg 0.75 and the Eating Inventory hunger score contributed significantly to the between subject variance in energy intake, whereas exercise energy expenditure did not. Regardless of exercise, eight women consistently restricted their energy intake (undereaters), and seven other consumed excess energy (overeaters). Overeaters were distinguished by higher Eating Inventory disinhibition (P = 0.023) and hunger (p = 0.004) scores. The overeaters' diet had a higher fat content 34 +/- 1% (p = 0.007). Also, overeaters took a larger percentage of their daily energy, than that of undereaters, 27 +/- 1 energy intake in the evening, 13 +/- 2%, compared to undereaters, 7 +/- 1% (p = 0.005). We conclude that the Eating Inventory is useful for identifying reduced-obese women at risk of overeating, and these individuals may benefit from dietary counseling aimed at reducing fat intake and evening snacking.

IMPORTANCE OF MANGROVE TO REDUCE THE TSUNAMI WAVE ENERGY

Directory of Open Access Journals (Sweden)

Anastasia Neni Candra Purnamasari

2017-09-01

Full Text Available Mangrove has a very important role to reduce the tsunami wave energy. It is shown that the coastal areas have no vegetation or in this case will have an impact Mangrove forests greater damage due to tsunami waves than the coastal areas of vegetation. The purpose of the Term Paper is proved the importance of Mangrove to reduce the tsunami wave energy by comparing the various methods that have been observed in some case studies on the impact of the tsunami that occurred in several Asian countries in 2004 and case studies on ocean waves on the Gulf coast of south Florida. Based on the research results that could dampen Mangrove Tsunami wave energy. Tsunami wave energy can be reduced by several factors, namely mangrove species, tree size, vast mangrove forest, nature tree structure, and the size limit Mangrove forest (as far as how much of the ocean to the surface.

An Energy Policy Analysis and Proposed Remedial Actions to Reduce Energy Crises in Pakistan

Directory of Open Access Journals (Sweden)

GHOUS BUX NAREJO

2017-04-01

Full Text Available Pakistan energy demand has grown exponentially over the last 2 decades. Reason behind increasing energy demand is excessive mobility of rural population to cities, rapid progression in industrial and transport sector, lack of policy making and implementation on the developed policies and improvements in living style. At present, Pakistan witness 5000-7000 MW power deficit in summer. To reduce the demand and supply gap, power plants across Pakistan are planned to be installed while some are under development phase. Power expansion plans cannot cope with the current energy shortfall since several years are required for them to get fully operational. Effective energy policy is the only key to address the existing shortfall. This paper discusses the initiatives that may be taken to reduce the power shortfall using energy efficiency and conservation, deployment of microgrids, utilization of renewable energy resources and effective research and development in energy sector. Since another most important issue evaluated in the research regarding the energy crises is energy efficiency and lack of compliance to government regulations for energy efficiency and conservation. Implementation on the policies developed for energy efficiencies and conservation has not been witnessed. Possible solutions on short term basis to lessen the energy crises have also been discussed in the paper

Making renewable energy competitive in India: Reducing financing costs via a government-sponsored hedging facility

International Nuclear Information System (INIS)

Farooquee, Arsalan Ali; Shrimali, Gireesh

2016-01-01

In India, a significant barrier to market-competitiveness of renewable energy is a shortage of attractive debt. Domestic debt has high cost, short tenors, and variable interest rates, adding 30% to the cost of renewable energy compared to renewable energy projects elsewhere. Foreign debt is as expensive as domestic debt because it requires costly market-based currency hedging solutions. We investigate a government-sponsored foreign exchange facility as an alternative to reducing hedging costs. Using the geometric Brownian motion (GBM) as a representative stochastic model of the INR–USD foreign exchange rate, we find that the expected cost of providing a currency hedge via this facility is 3.5 percentage points, 50% lower than market. This leads to an up to 9% reduction in the per unit cost of renewable energy. However, this requires the government to manage the risks related to unexpected currency movements appropriately. One option to manage these risks is via a capital buffer; for the facility to obtain India's sovereign rating, the capital buffer would need to be almost 30% of the underlying loan. Our findings have significant policy implications given that the Indian government can use this facility to make renewable energy more competitive and, therefore, hasten its deployment. - Highlights: • We analyze a government-sponsored foreign exchange facility in India. •We use geometric Brownian motion to represent the INR–USD exchange rate. •This facility can reduce the currency hedging costs by 50%. •This facility can reduce the levelized cost of renewable energy by 9%. •The capital buffer to reach India's sovereign rating is 30% of the original loan.

Reducing the energy penalty costs of postcombustion CCS systems with amine-storage.

Science.gov (United States)

Patiño-Echeverri, Dalia; Hoppock, David C

2012-01-17

Carbon capture and storage (CCS) can significantly reduce the amount of CO(2) emitted from coal-fired power plants but its operation significantly reduces the plant's net electrical output and decreases profits, especially during times of high electricity prices. An amine-based CCS system can be modified adding amine-storage to allow postponing 92% of all its energy consumption to times of lower electricity prices, and in this way has the potential to effectively reduce the cost of CO(2) capture by reducing the costs of the forgone electricity sales. However adding amine-storage to a CCS system implies a significant capital cost that will be outweighed by the price-arbitrage revenue only if the difference between low and high electricity prices is substantial. In this paper we find a threshold for the variability in electricity prices that make the benefits from electricity price arbitrage outweigh the capital costs of amine-storage. We then look at wholesale electricity markets in the Eastern Interconnect of the United States to determine profitability of amine-storage systems in this region. Using hourly electricity price data from years 2007 and 2008 we find that amine storage may be cost-effective in areas with high price variability.

Eating energy-Identifying possibilities for reduced energy use in the future food supply system

International Nuclear Information System (INIS)

Wallgren, Christine; Hoejer, Mattias

2009-01-01

This paper explores the possibilities for reducing future energy use for eating to a sustainable level. A backcasting approach is used to generate an image of the future where energy use for eating is 60% lower in 2050 than in 2000. The currently known potential to reduce energy use in the food supply system for producing, transporting, storing, cooking and eating food is explored and described in terms of a number of distinct changes that are numbered consecutively and presented in both a quantitative and qualitative way. Sweden is used as the case and all data regarding energy use apply for Swedish conditions. An exercise like this illustrates the possible outcome of taking sustainability seriously. If sustainability is to be achieved, some images of the future are needed so that potential targets can be identified. This paper does not present forecasts, but illustrates the kind of changes needed in order to achieve sustainable energy use in the food system.

Drops of energy: conserving urban water to reduce greenhouse gas emissions.

Science.gov (United States)

Zhou, Yuanchun; Zhang, Bing; Wang, Haikun; Bi, Jun

2013-10-01

Water and energy are two essential resources of modern civilization and are inherently linked. Indeed, the optimization of the water supply system would reduce energy demands and greenhouse gas emissions in the municipal water sector. This research measured the climatic cobenefit of water conservation based on a water flow analysis. The results showed that the estimated energy consumption of the total water system in Changzhou, China, reached approximately 10% of the city's total energy consumption, whereas the industrial sector was found to be more energy intensive than other sectors within the entire water system, accounting for nearly 70% of the total energy use of the water system. In addition, four sustainable water management scenarios would bring the cobenefit of reducing the total energy use of the water system by 13.9%, and 77% of the energy savings through water conservation was indirect. To promote sustainable water management and reduce greenhouse gas emissions, China would require its water price system, both for freshwater and recycled water, to be reformed.

MO-FG-204-03: Using Edge-Preserving Algorithm for Significantly Improved Image-Domain Material Decomposition in Dual Energy CT

International Nuclear Information System (INIS)

Zhao, W; Niu, T; Xing, L; Xiong, G; Elmore, K; Min, J; Zhu, J; Wang, L

2015-01-01

Purpose: To significantly improve dual energy CT (DECT) imaging by establishing a new theoretical framework of image-domain material decomposition with incorporation of edge-preserving techniques. Methods: The proposed algorithm, HYPR-NLM, combines the edge-preserving non-local mean filter (NLM) with the HYPR-LR (Local HighlY constrained backPRojection Reconstruction) framework. Image denoising using HYPR-LR framework depends on the noise level of the composite image which is the average of the different energy images. For DECT, the composite image is the average of high- and low-energy images. To further reduce noise, one may want to increase the window size of the filter of the HYPR-LR, leading resolution degradation. By incorporating the NLM filtering and the HYPR-LR framework, HYPR-NLM reduces the boost material decomposition noise using energy information redundancies as well as the non-local mean. We demonstrate the noise reduction and resolution preservation of the algorithm with both iodine concentration numerical phantom and clinical patient data by comparing the HYPR-NLM algorithm to the direct matrix inversion, HYPR-LR and iterative image-domain material decomposition (Iter-DECT). Results: The results show iterative material decomposition method reduces noise to the lowest level and provides improved DECT images. HYPR-NLM significantly reduces noise while preserving the accuracy of quantitative measurement and resolution. For the iodine concentration numerical phantom, the averaged noise levels are about 2.0, 0.7, 0.2 and 0.4 for direct inversion, HYPR-LR, Iter- DECT and HYPR-NLM, respectively. For the patient data, the noise levels of the water images are about 0.36, 0.16, 0.12 and 0.13 for direct inversion, HYPR-LR, Iter-DECT and HYPR-NLM, respectively. Difference images of both HYPR-LR and Iter-DECT show edge effect, while no significant edge effect is shown for HYPR-NLM, suggesting spatial resolution is well preserved for HYPR-NLM. Conclusion: HYPR

Optimizing residence time, temperature and speed to improve TMP pulp properties and reduce energy

Energy Technology Data Exchange (ETDEWEB)

Sabourin, M.; Xu, E.; Cort, B.; Boileau, I.; Waller, A.

1997-04-01

The concept of reducing energy consumption in pulp mills by increasing the disc speed of refining has been established using single disc and double disc refiners in both pilot plant and mill applications. The RTS study evaluated in this paper reviews the effect of high-speed single disc refining coupled with shortdwell-high pressure retention conditions. Coupling these variables permitted evaluation of an optimum residence time, temperature and speed (RTS) operational window. The objective of the RTS conditions to sufficiently soften the wood chips through high temperature such that the fibre is more receptive to initial defiberization at high intensity. The improved pulp from the primary refiner at high intensity could potentially demonstrate improvements in physical pulp properties at a reduced specific energy requirement. The spruce/fir RTS-TMP described here required significantly less specific energy and produced TMP with slightly improved strength properties and equivalent optical properties compared to conventional TMP pulp. Studies on the radiate pine furnish indicated that the physical pulp property/specific energy relationships could be adjusted by manipulating the residence time. 4 refs., 10 tabs., 10 figs.

Dynamic energy conservation model REDUCE. Extension with experience curves, energy efficiency indicators and user's guide

International Nuclear Information System (INIS)

Uyterlinde, M.A.; Rijkers, F.A.M.

1999-12-01

The main objective of the energy conservation model REDUCE (Reduction of Energy Demand by Utilization of Conservation of Energy) is the evaluation of the effectiveness of economical, financial, institutional, and regulatory measures for improving the rational use of energy in end-use sectors. This report presents the results of additional model development activities, partly based on the first experiences in a previous project. Energy efficiency indicators have been added as an extra tool for output analysis in REDUCE. The methodology is described and some examples are given. The model has been extended with a method for modelling the effects of technical development on production costs, by means of an experience curve. Finally, the report provides a 'users guide', by describing in more detail the input data specification as well as all menus and buttons. 19 refs

Reducing heat loss from the energy absorber of a solar collector

Science.gov (United States)

Chao, Bei Tse; Rabl, Ari

1976-01-01

A device is provided for reducing convective heat loss in a cylindrical radiant energy collector. It includes a curved reflective wall in the shape of the arc of a circle positioned on the opposite side of the exit aperture from the reflective side walls of the collector. Radiant energy exiting the exit aperture is directed by the curved wall onto an energy absorber such that the portion of the absorber upon which the energy is directed faces downward to reduce convective heat loss from the absorber.

Spectroscopic probes of vibrationally excited molecules at chemically significant energies

Energy Technology Data Exchange (ETDEWEB)

Rizzo, T.R. [Univ. of Rochester, NY (United States)

1993-12-01

This project involves the application of multiple-resonance spectroscopic techniques for investigating energy transfer and dissociation dynamics of highly vibrationally excited molecules. Two major goals of this work are: (1) to provide information on potential energy surfaces of combustion related molecules at chemically significant energies, and (2) to test theoretical modes of unimolecular dissociation rates critically via quantum-state resolved measurements.

Fructo-oligosaccharides reduce energy intake but do not affect adiposity in rats fed a low-fat diet but increase energy intake and reduce fat mass in rats fed a high-fat diet.

Science.gov (United States)

Hadri, Zouheyr; Rasoamanana, Rojo; Fromentin, Gilles; Azzout-Marniche, Dalila; Even, Patrick C; Gaudichon, Claire; Darcel, Nicolas; Bouras, Abdelkader Dilmi; Tomé, Daniel; Chaumontet, Catherine

2017-12-01

The ingestion of low or high lipid diets enriched with fructo-oligosaccharide (FOS) affects energy homeostasis. Ingesting protein diets also induces a depression of energy intake and decreases body weight. The goal of this study was to investigate the ability of FOS, combined or not with a high level of protein (P), to affect energy intake and body composition when included in diets containing different levels of lipids (L). We performed two studies of similar design over a period of 5weeks. During the first experiment (exp1), after a 3-week period of adaptation to a normal protein-low fat diet, the rats received one of the following four diets for 5weeks (6 rats per group): (i) normal protein (14% P/E (Energy) low fat (10% L/E) diet, (ii) normal protein, low fat diet supplemented with 10% FOS, (iii) high protein (55%P/E) low fat diet, and (iv) high protein, low fat diet supplemented with 10% FOS. In a second experiment (exp2) after the 3-week period of adaptation to a normal protein-high fat diet, the rats received one of the following 4 diets for 5weeks (6 rats per group): (i) normal protein, high fat diet (35% of fat), (ii) normal protein, high fat diet supplemented with 10% FOS, (iii) high protein high fat diet and (iv) high protein high fat diet supplemented with 10% FOS. In low-fat fed rats, FOS did not affect lean body mass (LBM) and fat mass but the protein level reduced fat mass and tended to reduce adiposity. In high-fat fed rats, FOS did not affect LBM but reduced fat mass and adiposity. No additive or antagonistic effects between FOS and the protein level were observed. FOS reduced energy intake in low-fat fed rats, did not affect energy intake in normal-protein high-fat fed rats but surprisingly, and significantly, increased energy intake in high-protein high-fat fed rats. The results thus showed that FOS added to a high-fat diet reduced body fat and body adiposity. Published by Elsevier Inc.

Noninvasive ventilation reduces energy expenditure in amyotrophic lateral sclerosis.

Science.gov (United States)

Georges, Marjolaine; Morélot-Panzini, Capucine; Similowski, Thomas; Gonzalez-Bermejo, Jesus

2014-02-07

Amyotrophic lateral sclerosis (ALS) leads to chronic respiratory failure. Diaphragmatic dysfunction, a major driver of dyspnea and mortality, is associated with a shift of the burden of ventilation to extradiaphragmatic inspiratory muscles, including neck muscles. Besides, energy expenditure is often abnormally high in ALS, and this is associated with a negative prognostic value. We hypothesized that noninvasive ventilation (NIV) would relieve inspiratory neck muscles and reduce resting energy expenditure (REE). Using indirect calorimetry, we measured REE during spontaneous breathing (REESB) and NIV (REENIV) in 16 ALS patients with diaphragmatic dysfunction, during the first 3 months of NIV. Measured values were compared with predicted REE (REEpred)(Harris-Benedict equation). NIV abolished inspiratory neck muscle activity. Even though our patients were not hypermetabolic, on the contrary, with a REESB that was lower than REEpred (average 11%), NIV did reduce energy expenditure. Indeed, median REENIV, in this population with a mean body mass index of 21.4 kg.m-2, was 1149 kcal/24 h [interquartile 970-1309], lower than REESB (1197 kcal/24 h, 1054-1402; mean difference 7%; p = 0.03, Wilcoxon). REESB and REENIV were correlated with forced vital capacity and maximal inspiratory pressure. NIV can reduce energy expenditure in ALS patients probably by alleviating the ventilatory burden imposed on inspiratory neck muscles to compensate diaphragm weakness. It remains to be elucidated whether or not, in which population, and to what extent, NIV can be beneficial in ALS through the corresponding reduction in energy expenditure.

Significant decimal digits for energy representation on short-word computers

International Nuclear Information System (INIS)

Sartori, E.

1989-01-01

The general belief that single precision floating point numbers have always at least seven significant decimal digits on short word computers such as IBM is erroneous. Seven significant digits are required however for representing the energy variable in nuclear cross-section data sets containing sharp p-wave resonances at 0 Kelvin. It is suggested that either the energy variable is stored in double precision or that cross-section resonances are reconstructed to room temperature or higher on short word computers

Lorcaserin, a 5-HT(2C) receptor agonist, reduces body weight by decreasing energy intake without influencing energy expenditure.

Science.gov (United States)

Martin, Corby K; Redman, Leanne M; Zhang, Jinkun; Sanchez, Matilde; Anderson, Christen M; Smith, Steven R; Ravussin, Eric

2011-03-01

Lorcaserin, a selective 5-hydroxytryptamine (5-HT)(2C) receptor agonist, reduces body weight. It is unclear whether weight loss is due to reduced energy intake (EI) or also to enhanced energy expenditure (EE). This study tested the effect of lorcaserin on EI and EE. In a double-blind, randomized, placebo-controlled trial, 57 (39 women) overweight and obese (body mass index, 27-45 kg/m(2)) adults were randomized to placebo (n = 28) or 10 mg twice daily lorcaserin (n = 29) for 56 d. Weight maintenance was imposed during d 1-7. Beginning on d 8, participants followed a diet and exercise plan targeting a 600 kcal/d deficit. At baseline and after 7 and 56 d of treatment, we measured body weight, body composition (dual x-ray absorptiometry), blood pressure, heart rate, EI at lunch and dinner, subjective appetite ratings, and 24-h EE and 24-h-respiratory quotient (RQ), measured by indirect calorimetry in a respiratory chamber. After 7 d of weight maintenance, EI was significantly (P kcal; placebo, -147 ± 89 kcal). After 56 d, lorcaserin resulted in significantly larger reductions in body weight (lorcaserin, -3.8 ± 0.4 kg; placebo, -2.2 ± 0.5 kg; P kcal; placebo, -205 ± 91 kcal; P < .05), and appetite ratings than in placebo. Changes in 24-h EE and 24-h RQ did not differ between groups, even after 24-h EE was adjusted for body weight and composition. Compared with placebo, lorcaserin had no effect on systolic or diastolic blood pressure or heart rate after 56 d. Lorcaserin reduces body weight through reduced EI, not altered EE or RQ.

Low-energy shock wave preconditioning reduces renal ischemic reperfusion injury caused by renal artery occlusion.

Science.gov (United States)

Xue, Yuquan; Xu, Zhibin; Chen, Haiwen; Gan, Weimin; Chong, Tie

2017-07-01

To evaluate whether low energy shock wave preconditioning could reduce renal ischemic reperfusion injury caused by renal artery occlusion. The right kidneys of 64 male Sprague Dawley rats were removed to establish an isolated kidney model. The rats were then divided into four treatment groups: Group 1 was the sham treatment group; Group 2, received only low-energy (12 kv, 1 Hz, 200 times) shock wave preconditioning; Group 3 received the same low-energy shock wave preconditioning as Group 2, and then the left renal artery was occluded for 45 minutes; and Group 4 had the left renal artery occluded for 45 minutes. At 24 hours and one-week time points after reperfusion, serum inducible nitric oxide synthase (iNOS), neutrophil gelatinase-associated lipocalin (NGAL), kidney injury molecule-1 (KIM-1), creatinine (Cr), and cystatin C (Cys C) levels were measured, malondialdehyde (MDA) in kidney tissue was detected, and changes in nephric morphology were evaluated by light and electron microscopy. Twenty-four hours after reperfusion, serum iNOS, NGAL, Cr, Cys C, and MDA levels in Group 3 were significantly lower than those in Group 4; light and electron microscopy showed that the renal tissue injury in Group 3 was significantly lighter than that in Group 4. One week after reperfusion, serum NGAL, KIM-1, and Cys C levels in Group 3 were significantly lower than those in Group 4. Low-energy shock wave preconditioning can reduce renal ischemic reperfusion injury caused by renal artery occlusion in an isolated kidney rat model.

The Role of Secure Access to Sustainable Energy in Reducing ...

African Journals Online (AJOL)

The Role of Secure Access to Sustainable Energy in Reducing Women's ... of poverty, such as low education levels, inadequate health care and limited ... women in relation to energy will help governments promote overall development goals ...

Control Motion Approach of a Lower Limb Orthosis to Reduce Energy Consumption

Directory of Open Access Journals (Sweden)

Daniel Sanz-Merodio

2012-12-01

Full Text Available By analysing the dynamic principles of the human gait, an economic gait-control analysis is performed, and passive elements are included to increase the energy efficiency in the motion control of active orthoses. Traditional orthoses use position patterns from the clinical gait analyses (CGAs of healthy people, which are then de-normalized and adjusted to each user. These orthoses maintain a very rigid gait, and their energy cost is very high, reducing the autonomy of the user. First, to take advantage of the inherent dynamics of the legs, a state machine pattern with different gains in each state is applied to reduce the actuator energy consumption. Next, different passive elements, such as springs and brakes in the joints, are analysed to further reduce energy consumption. After an off-line parameter optimization and a heuristic improvement with genetic algorithms, a reduction in energy consumption of 16.8% is obtained by applying a state machine control pattern, and a reduction of 18.9% is obtained by using passive elements. Finally, by combining both strategies, a more natural gait is obtained, and energy consumption is reduced by 24.6% compared with a pure CGA pattern.

Design and implementation of Ad-Hoc collaborative proxying scheme for reducing network energy waste

Directory of Open Access Journals (Sweden)

Rafiullah Khan

2017-05-01

Full Text Available Network devices are equipped with low power states but they are rarely activated due to their inability of maintaining network connectivity. Recently, Network Connectivity Proxy (NCP concept has been proposed in literature as an effective mechanism to exploit full potential of low power features on network devices by impersonating their virtual presence. However, the NCP concept faces several open issues and challenges especially related to proxying of TCP connections and majority of daily used proprietary closed-source applications. This paper presents a new approach for reducing network energy waste through intelligent collaboration among daily used devices (e.g., desktop computers, laptops, tablets, smartphones, etc. It guarantees to run applications on only and only one user device that is under active use at that specific moment. To reduce energy waste and allow idle devices to sleep, our approach also takes benefit from a light-weight home gateway proxy with very basic practically realizable functionalities. The proposed system not just reduces energy waste of fixed devices but also enables mobile devices to significantly improve their battery life. Our developed software prototypes allow devices to autonomously and seamlessly collaborate with each other without requiring any configuration or user input. Further, this paper also presents the basic performance evaluation of developed prototypes in real networking environments.

Columbia, Missouri: Using Energy Data to Reduce Emissions and Achieve Low-Income Household Energy Savings (City Energy: From Data to Decisions)

Energy Technology Data Exchange (ETDEWEB)

Office of Strategic Programs, Strategic Priorities and Impact Analysis Team

2017-09-29

This fact sheet "Columbia, Missouri: Using Energy Data to Reduce Emissions and Achieve Low-Income Household Energy Savings" explains how the City of Columbia used data from the U.S. Department of Energy's Cities Leading through Energy Analysis and Planning (Cities-LEAP) and the State and Local Energy Data (SLED) programs to inform its city energy planning. It is one of ten fact sheets in the "City Energy: From Data to Decisions" series.

Identifying opportunities to reduce the consumption of energy across mining and processing plants

Energy Technology Data Exchange (ETDEWEB)

Sterling, David; Johnson, Greg

2010-09-15

In addition to meeting Government Policy on Energy Efficiency Opportunities (EEOs), mining and mineral processing companies are increasing energy efficiency to reduce costs in the current financial conditions. One of the major issues with EEOs is the lack of data available on energy use, and more importantly the energy use linked to production data, that identify energy reduction opportunities. This paper looks at expanding the use of a Manufacturing Execution Systems by integrating with Energy Solutions. This will provide automatic, timely information, at a granularity that makes it easier to identify EEOs, reduce energy costs, and better predict energy use.

Energy-efficient pulse-coupled synchronization strategy design for wireless sensor networks through reduced idle listening

Science.gov (United States)

Wang, Yongqiang; Núñez, Felipe; Doyle, Francis J.

2013-01-01

Synchronization is crucial to wireless sensor networks due to their decentralized structure. We propose an energy-efficient pulse-coupled synchronization strategy to achieve this goal. The basic idea is to reduce idle listening by intentionally introducing a large refractory period in the sensors’ cooperation. The large refractory period greatly reduces idle listening in each oscillation period, and is analytically proven to have no influence on the time to synchronization. Hence, it significantly reduces the total energy consumption in a synchronization process. A topology control approach tailored for pulse-coupled synchronization is given to guarantee a k-edge strongly connected interaction topology, which is tolerant to communication-link failures. The topology control approach is totally decentralized and needs no information exchange among sensors, and it is applicable to dynamic network topologies as well. This facilitates a completely decentralized implementation of the synchronization strategy. The strategy is applicable to mobile sensor networks, too. QualNet case studies confirm the effectiveness of the synchronization strategy. PMID:24307831

Reducing supply chain energy use in next-generation vehicle lightweighting

Energy Technology Data Exchange (ETDEWEB)

Hanes, Rebecca J.; Das, Sujit; Carpenter, Alberta

2016-09-29

Vehicle lightweighting reduces the amount of fuel consumed in a vehicle's use phase, but depending on what lightweight materials replace the conventional materials, and in what amounts, the manufacturing energy may increase or decrease. For carbon fiber reinforced polymer (CFRP), a next-generation lightweighting material, the increase in vehicle manufacturing energy is greater than the fuel savings, resulting in a net increase in energy consumption over a vehicle's manufacturing and use relative to a standard non-lightweighted car. [1] This work explores ways to reduce the supply chain energy of CFRP lightweighted vehicles through alternative production technologies and energy efficiency improvements. The objective is to determine if CFRP can offer energy savings comparable to or greater than aluminum, a conventional lightweighting material. Results of this analysis can be used to inform additional research and development efforts in CFRP production and future directions in lightweight vehicle production. The CFRP supply chain is modeled using the Material Flows through Industry (MFI) scenario modeling tool, which calculates 'mine to materials' energy consumption, material inventories and greenhouse gas emissions for industrial supply chains. In this analysis, the MFI tool is used to model the supply chains of two lightweighted vehicles, an aluminum intensive vehicle (AIV) and a carbon fiber intensive vehicle (CFV), under several manufacturing scenarios. Vehicle specifications are given in [1]. Scenarios investigated cover alternative carbon fiber (CF) feedstocks and energy efficiency improvements at various points in the vehicle supply chains. The alternative CF feedstocks are polyacrylonitrile, lignin and petroleum-derived mesophase pitch. Scenarios in which the energy efficiency of CF and CFRP production increases are explored using sector efficiency potential values, which quantify the reduction in energy consumption achievable when process

Potential for the Use of Energy Savings Performance Contracts to Reduce Energy Consumption and Provide Energy and Cost Savings in Non-Building Applications

Energy Technology Data Exchange (ETDEWEB)

Williams, Charles; Green, Andrew S.; Dahle, Douglas; Barnett, John; Butler, Pat; Kerner, David

2013-08-01

The findings of this study indicate that potential exists in non-building applications to save energy and costs. This potential could save billions of federal dollars, reduce reliance on fossil fuels, increase energy independence and security, and reduce greenhouse gas emissions. The Federal Government has nearly twenty years of experience with achieving similar energy cost reductions, and letting the energy costs savings pay for themselves, by applying energy savings performance contracts (ESPC) inits buildings. Currently, the application of ESPCs is limited by statute to federal buildings. This study indicates that ESPCs can be a compatible and effective contracting tool for achieving savings in non-building applications.

Reducing Operating Costs and Energy Consumption at Water Utilities

Science.gov (United States)

Due to their unique combination of high energy usage and potential for significant savings, utilities are turning to energy-efficient technologies to help save money. Learn about cost and energy saving technologies from this brochure.

Easing the natural gas crisis: Reducing natural gas prices through increased deployment of renewable energy and energy efficiency

Energy Technology Data Exchange (ETDEWEB)

Wiser, Ryan; Bolinger, Mark; St. Clair, Matt

2004-12-21

Heightened natural gas prices have emerged as a key energy-policy challenge for at least the early part of the 21st century. With the recent run-up in gas prices and the expected continuation of volatile and high prices in the near future, a growing number of voices are calling for increased diversification of energy supplies. Proponents of renewable energy and energy efficiency identify these clean energy sources as an important part of the solution. Increased deployment of renewable energy (RE) and energy efficiency (EE) can hedge natural gas price risk in more than one way, but this paper touches on just one potential benefit: displacement of gas-fired electricity generation, which reduces natural gas demand and thus puts downward pressure on gas prices. Many recent modeling studies of increased RE and EE deployment have demonstrated that this ''secondary'' effect of lowering natural gas prices could be significant; as a result, this effect is increasingly cited as justification for policies promoting RE and EE. This paper summarizes recent studies that have evaluated the gas-price-reduction effect of RE and EE deployment, analyzes the results of these studies in light of economic theory and other research, reviews the reasonableness of the effect as portrayed in modeling studies, and develops a simple tool that can be used to evaluate the impact of RE and EE on gas prices without relying on a complex national energy model. Key findings are summarized.

Steam Pressure-Reducing Station Safety and Energy Efficiency Improvement Project

Energy Technology Data Exchange (ETDEWEB)

Lower, Mark D [ORNL; Christopher, Timothy W [ORNL; Oland, C Barry [ORNL

2011-06-01

The Facilities and Operations (F&O) Directorate is sponsoring a continuous process improvement (CPI) program. Its purpose is to stimulate, promote, and sustain a culture of improvement throughout all levels of the organization. The CPI program ensures that a scientific and repeatable process exists for improving the delivery of F&O products and services in support of Oak Ridge National Laboratory (ORNL) Management Systems. Strategic objectives of the CPI program include achieving excellence in laboratory operations in the areas of safety, health, and the environment. Identifying and promoting opportunities for achieving the following critical outcomes are important business goals of the CPI program: improved safety performance; process focused on consumer needs; modern and secure campus; flexibility to respond to changing laboratory needs; bench strength for the future; and elimination of legacy issues. The Steam Pressure-Reducing Station (SPRS) Safety and Energy Efficiency Improvement Project, which is under the CPI program, focuses on maintaining and upgrading SPRSs that are part of the ORNL steam distribution network. This steam pipe network transports steam produced at the ORNL steam plant to many buildings in the main campus site. The SPRS Safety and Energy Efficiency Improvement Project promotes excellence in laboratory operations by (1) improving personnel safety, (2) decreasing fuel consumption through improved steam system energy efficiency, and (3) achieving compliance with applicable worker health and safety requirements. The SPRS Safety and Energy Efficiency Improvement Project being performed by F&O is helping ORNL improve both energy efficiency and worker safety by modifying, maintaining, and repairing SPRSs. Since work began in 2006, numerous energy-wasting steam leaks have been eliminated, heat losses from uninsulated steam pipe surfaces have been reduced, and deficient pressure retaining components have been replaced. These improvements helped ORNL

The significance of reduced respiratory chain enzyme activities: clinical, biochemical and radiological associations.

Science.gov (United States)

Mordekar, S R; Guthrie, P; Bonham, J R; Olpin, S E; Hargreaves, I; Baxter, P S

2006-03-01

Mitochondrial diseases are an important group of neurometabolic disorders in children with varied clinical presentations and diagnosis that can be difficult to confirm. To report the significance of reduced respiratory chain enzyme (RCE) activity in muscle biopsy samples from children. Retrospective odds ratio was used to compare clinical and biochemical features, DNA studies, neuroimaging, and muscle biopsies in 18 children with and 48 without reduced RCE activity. Children with reduced RCE activity were significantly more likely to have consanguineous parents, to present with acute encephalopathy and lactic acidaemia and/or within the first year of life; to have an axonal neuropathy, CSF lactate >4 mmol/l; and/or to have signal change in the basal ganglia. There were positive associations with a maternal family history of possible mitochondrial cytopathy; a presentation with failure to thrive and lactic acidaemia, ragged red fibres, reduced fibroblast fatty acid oxidation and with an abnormal allopurinol loading test. There was no association with ophthalmic abnormalities, deafness, epilepsy or myopathy. The association of these clinical, biochemical and radiological features with reduced RCE activity suggests a possible causative link.

High-efficiency pumps drastically reduce energy consumption

Energy Technology Data Exchange (ETDEWEB)

Anon

2002-05-01

Wilo's Stratos pumps for air conditioning and other domestic heating applications combine the advantages of wet runner technology with an innovative electronic commutator motor. The energy consumption of these high-efficiency pumps is halved compared with similar wet runner designs. With vast numbers of pumps used in buildings across Europe alone, the adoption of this technology potentially offers significant energy sayings. (Author)

Development of the Croatian Energy Sector by 2050 in Terms of Reducing Carbon Dioxide Emissions

International Nuclear Information System (INIS)

Granic, G.; Pesut, D.; Tot, M.; Juric, Z.; Horvath, L.; Bacan, A.; Kulisic, B.; Majstorovic, G.

2012-01-01

The paper analyzes the question: is it possible to achieve and what would be the consequences of energy development while reducing CO 2 emissions by 80% by year 2050. Thereby, the growth of costs is not the only expected consequence, but there are also desirable and possible impacts of the energy sector on technological development, science, the economy and increasing the added value. In paper, the development of the energy sector by 2050 is modeled and simulated using two models for the evaluation of the energy systems: model for the analysis of energy consumption (MAED - Model for Energy System Analysis ) and model for optimization of energy supply systems (MESSAGE - Model for Energy Supply Strategy Alternatives and their General Environmental Impacts ). MESSAGE use the results of MAED model as input assumptions and data. Development opportunities in the sectors of industry, households, services and transport were modeled in the simulation, i.e. possible trajectories of development were considered, in order to achieve the objectives of the sectoral reducing of CO 2 emissions in line with the stated objectives which are discussed at the EU level. The average cost of electricity production in year 2050 will increase by nearly 140% compared to the year 2015. The answer is: the reduction of CO 2 emissions in Croatia by 80% in total and by 95% in the power sector is possible from a technical and technological point of view, but with the high financial impact and significant changes in the energy sector, to which should precede changes in scientific and industrial development.(author)

Basking hamsters reduce resting metabolism, body temperature and energy costs during rewarming from torpor.

Science.gov (United States)

Geiser, Fritz; Gasch, Kristina; Bieber, Claudia; Stalder, Gabrielle L; Gerritsmann, Hanno; Ruf, Thomas

2016-07-15

Basking can substantially reduce thermoregulatory energy expenditure of mammals. We tested the hypothesis that the largely white winter fur of hamsters (Phodopus sungorus), originating from Asian steppes, may be related to camouflage to permit sun basking on or near snow. Winter-acclimated hamsters in our study were largely white and had a high proclivity to bask when resting and torpid. Resting hamsters reduced metabolic rate (MR) significantly (>30%) when basking at ambient temperatures (Ta) of ∼15 and 0°C. Interestingly, body temperature (Tb) also was significantly reduced from 34.7±0.6°C (Ta 15°C, not basking) to 30.4±2.0°C (Ta 0°C, basking), which resulted in an extremely low (thermal conductance. Induced torpor (food withheld) during respirometry at Ta 15°C occurred on 83.3±36.0% of days and the minimum torpor MR was 36% of basal MR at an average Tb of 22.0±2.6°C; movement to the basking lamp occurred at Tb50%) during radiant heat-assisted rewarming; however, radiant heat per se without an endogenous contribution by animals did not strongly affect metabolism and Tb during torpor. Our data show that basking substantially modifies thermal energetics in hamsters, with a drop of resting Tb and MR not previously observed and a reduction of rewarming costs. The energy savings afforded by basking in hamsters suggest that this behaviour is of energetic significance not only for mammals living in deserts, where basking is common, but also for P. sungorus and probably other cold-climate mammals. © 2016. Published by The Company of Biologists Ltd.

Synthesis and Exciton Dynamics of Donor-Orthogonal Acceptor Conjugated Polymers: Reducing the Singlet–Triplet Energy Gap

KAUST Repository

Freeman, David M. E.; Musser, Andrew J.; Frost, Jarvist M.; Stern, Hannah L.; Forster, Alexander K.; Fallon, Kealan J.; Rapidis, Alexandros G.; Cacialli, Franco; McCulloch, Iain; Clarke, Tracey M.; Friend, Richard H.; Bronstein, Hugo

2017-01-01

The presence of energetically low-lying triplet states is a hallmark of organic semiconductors. Even though they present a wealth of interesting photophysical properties, these optically dark states significantly limit optoelectronic device performance. Recent advances in emissive charge-transfer molecules have pioneered routes to reduce the energy gap between triplets and

Synthesis and Exciton Dynamics of Donor-Orthogonal Acceptor Conjugated Polymers: Reducing the Singlet–Triplet Energy Gap

KAUST Repository

Freeman, David M. E.

2017-06-09

The presence of energetically low-lying triplet states is a hallmark of organic semiconductors. Even though they present a wealth of interesting photophysical properties, these optically dark states significantly limit optoelectronic device performance. Recent advances in emissive charge-transfer molecules have pioneered routes to reduce the energy gap between triplets and

Partial Sleep Deprivation Reduces the Efficacy of Orexin-A to Stimulate Physical Activity and Energy Expenditure.

Science.gov (United States)

DePorter, Danielle P; Coborn, Jamie E; Teske, Jennifer A

2017-10-01

Sufficient sleep is required for weight maintenance. Sleep deprivation due to noise exposure stimulates weight gain by increasing hyperphagia and reducing energy expenditure (EE). Yet the mechanistic basis underlying the weight gain response is unclear. Orexin-A promotes arousal and negative energy balance, and orexin terminals project to the ventrolateral preoptic area (VLPO), which is involved in sleep-to-wake transitions. To determine whether sleep deprivation reduces orexin function in VLPO and to test the hypothesis that sleep deprivation would attenuate the orexin-A-stimulated increase in arousal, physical activity (PA), and EE. Electroencephalogram, electromyogram, distance traveled, and EE were determined in male Sprague-Dawley rats following orexin-A injections into VLPO both before and after acute (12-h) and chronic (8 h/d, 9 d) sleep deprivation by noise exposure. Orexin-A in the VLPO significantly increased arousal, PA, total EE, and PA-related EE and reduced sleep and respiratory quotient before sleep deprivation. In contrast to after acute sleep deprivation in which orexin-A failed to stimulate EE during PA only, orexin-A failed to significantly increase arousal, PA, fat oxidation, total EE, and PA-related EE after chronic sleep deprivation. Sleep deprivation may reduce sensitivity to endogenous stimuli that enhance EE due to PA and thus stimulate weight gain. © 2017 The Obesity Society.

The High Costs of Low-Grade Inflammation: Persistent Fatigue as a Consequence of Reduced Cellular-Energy Availability and Non-adaptive Energy Expenditure.

Science.gov (United States)

Lacourt, Tamara E; Vichaya, Elisabeth G; Chiu, Gabriel S; Dantzer, Robert; Heijnen, Cobi J

2018-01-01

Chronic or persistent fatigue is a common, debilitating symptom of several diseases. Persistent fatigue has been associated with low-grade inflammation in several models of fatigue, including cancer-related fatigue and chronic fatigue syndrome. However, it is unclear how low-grade inflammation leads to the experience of fatigue. We here propose a model of an imbalance in energy availability and energy expenditure as a consequence of low-grade inflammation. In this narrative review, we discuss how chronic low-grade inflammation can lead to reduced cellular-energy availability. Low-grade inflammation induces a metabolic switch from energy-efficient oxidative phosphorylation to fast-acting, but less efficient, aerobic glycolytic energy production; increases reactive oxygen species; and reduces insulin sensitivity. These effects result in reduced glucose availability and, thereby, reduced cellular energy. In addition, emerging evidence suggests that chronic low-grade inflammation is associated with increased willingness to exert effort under specific circumstances. Circadian-rhythm changes and sleep disturbances might mediate the effects of inflammation on cellular-energy availability and non-adaptive energy expenditure. In the second part of the review, we present evidence for these metabolic pathways in models of persistent fatigue, focusing on chronic fatigue syndrome and cancer-related fatigue. Most evidence for reduced cellular-energy availability in relation to fatigue comes from studies on chronic fatigue syndrome. While the mechanistic evidence from the cancer-related fatigue literature is still limited, the sparse results point to reduced cellular-energy availability as well. There is also mounting evidence that behavioral-energy expenditure exceeds the reduced cellular-energy availability in patients with persistent fatigue. This suggests that an inability to adjust energy expenditure to available resources might be one mechanism underlying persistent fatigue.

Excavation-drier method of energy-peat extraction reduces long-term climatic impact

Energy Technology Data Exchange (ETDEWEB)

Silvan, N.; Silvan, K.; Laine, J. [Finnish Forest Research Inst., Parkano (Finland)], e-mail: niko.silvan@metla.fi; Vaisanen, S.; Soukka, R. [Lappeenranta Univ.of Techology (Finland)

2012-11-01

Climatic impacts of energy-peat extraction are of increasing concern due to EU emissions trading requirements. A new excavation-drier peat extraction method has been developed to reduce the climatic impact and increase the efficiency of peat extraction. To quantify and compare the soil GHG fluxes of the excavation drier and the traditional milling methods, as well as the areas from which the energy peat is planned to be extracted in the future (extraction reserve area types), soil CO{sub 2}, CH{sub 4} and N{sub 2}O fluxes were measured during 2006-2007 at three sites in Finland. Within each site, fluxes were measured from drained extraction reserve areas, extraction fields and stockpiles of both methods and additionally from the biomass driers of the excavation-drier method. The Life Cycle Assessment (LCA), described at a principal level in ISO Standards 14040:2006 and 14044:2006, was used to assess the long-term (100 years) climatic impact from peatland utilisation with respect to land use and energy production chains where utilisation of coal was replaced with peat. Coal was used as a reference since in many cases peat and coal can replace each other in same power plants. According to this study, the peat extraction method used was of lesser significance than the extraction reserve area type in regards to the climatic impact. However, the excavation-drier method seems to cause a slightly reduced climatic impact as compared with the prevailing milling method. (orig.)

New Hampshire Carbon Challenge: Reducing Residential Energy Use and Greenhouse Gas Emissions

Science.gov (United States)

Schloss, A. L.; Bartlett, D.; Blaha, D.; Skoglund, C.; Dundorf, J.; Froburg, E.; Pasinella, B.

2007-12-01

The New Hampshire Carbon Challenge is an initiative of the Institute for the Study of Earth, Oceans and Space at the University of New Hampshire. Our goal is to educate New Hampshire residents about climate change and also encourage them to reduce their household greenhouse gas emissions by 10,000 pounds. The Northeast region is undergoing climate changes consistent with those expected due to increasing levels of CO2 in the atmosphere, while also contributing to climate change as the world's seventh largest source of CO2 emissions. In the USA, approximately 40 percent of CO2 emissions from fossil fuel combustion come from residential energy consumption for space heating, electricity usage, and transportation. Homeowners typically are not aware that modest energy reductions can result in significant carbon savings. Most campaigns that raise awareness of climate change and residential energy usage disseminate information to consumers through newspaper articles, brochures, websites, or other traditional means of communication. These information-only campaigns have not been very effective in changing residential energy consumption. Bombarded with information in their daily lives, the public has become quite adept at tuning most of it out. When much of the information they receive about climate change is confusing and contradictory, residents have even less incentive to change their behavior. The Challenge is unique in that it couples accurate information about climate change with concrete actions homeowners can take to reduce their carbon emissions. Our strategy is to utilize the tools of Community Based Social Marketing, which has been shown to be effective in changing behavior, and also to leverage existing networks including the NH Department of Environmental Services, UNH Cooperative Extension, faith-based communities, municipal energy committees and Climate Project volunteers, to effectively reach residents throughout the state. The response to our program has

Reduced-cost second-order algebraic-diagrammatic construction method for excitation energies and transition moments

Science.gov (United States)

Mester, Dávid; Nagy, Péter R.; Kállay, Mihály

2018-03-01

A reduced-cost implementation of the second-order algebraic-diagrammatic construction [ADC(2)] method is presented. We introduce approximations by restricting virtual natural orbitals and natural auxiliary functions, which results, on average, in more than an order of magnitude speedup compared to conventional, density-fitting ADC(2) algorithms. The present scheme is the successor of our previous approach [D. Mester, P. R. Nagy, and M. Kállay, J. Chem. Phys. 146, 194102 (2017)], which has been successfully applied to obtain singlet excitation energies with the linear-response second-order coupled-cluster singles and doubles model. Here we report further methodological improvements and the extension of the method to compute singlet and triplet ADC(2) excitation energies and transition moments. The various approximations are carefully benchmarked, and conservative truncation thresholds are selected which guarantee errors much smaller than the intrinsic error of the ADC(2) method. Using the canonical values as reference, we find that the mean absolute error for both singlet and triplet ADC(2) excitation energies is 0.02 eV, while that for oscillator strengths is 0.001 a.u. The rigorous cutoff parameters together with the significantly reduced operation count and storage requirements allow us to obtain accurate ADC(2) excitation energies and transition properties using triple-ζ basis sets for systems of up to one hundred atoms.

A reduced energy supply strategy in active vibration control

Science.gov (United States)

Ichchou, M. N.; Loukil, T.; Bareille, O.; Chamberland, G.; Qiu, J.

2011-12-01

In this paper, a control strategy is presented and numerically tested. This strategy aims to achieve the potential performance of fully active systems with a reduced energy supply. These energy needs are expected to be comparable to the power demands of semi-active systems, while system performance is intended to be comparable to that of a fully active configuration. The underlying strategy is called 'global semi-active control'. This control approach results from an energy investigation based on management of the optimal control process. Energy management encompasses storage and convenient restitution. The proposed strategy monitors a given active law without any external energy supply by considering purely dissipative and energy-demanding phases. Such a control law is offered here along with an analysis of its properties. A suboptimal form, well adapted for practical implementation steps, is also given. Moreover, a number of numerical experiments are proposed in order to validate test findings.

A reduced energy supply strategy in active vibration control

International Nuclear Information System (INIS)

Ichchou, M N; Loukil, T; Bareille, O; Chamberland, G; Qiu, J

2011-01-01

In this paper, a control strategy is presented and numerically tested. This strategy aims to achieve the potential performance of fully active systems with a reduced energy supply. These energy needs are expected to be comparable to the power demands of semi-active systems, while system performance is intended to be comparable to that of a fully active configuration. The underlying strategy is called 'global semi-active control'. This control approach results from an energy investigation based on management of the optimal control process. Energy management encompasses storage and convenient restitution. The proposed strategy monitors a given active law without any external energy supply by considering purely dissipative and energy-demanding phases. Such a control law is offered here along with an analysis of its properties. A suboptimal form, well adapted for practical implementation steps, is also given. Moreover, a number of numerical experiments are proposed in order to validate test findings

Microencapsulated bitter compounds (from Gentiana lutea) reduce daily energy intakes in humans.

Science.gov (United States)

Mennella, Ilario; Fogliano, Vincenzo; Ferracane, Rosalia; Arlorio, Marco; Pattarino, Franco; Vitaglione, Paola

2016-11-10

Mounting evidence showed that bitter-tasting compounds modulate eating behaviour through bitter taste receptors in the gastrointestinal tract. This study aimed at evaluating the influence of microencapsulated bitter compounds on human appetite and energy intakes. A microencapsulated bitter ingredient (EBI) with a core of bitter Gentiana lutea root extract and a coating of ethylcellulose-stearate was developed and included in a vanilla microencapsulated bitter ingredient-enriched pudding (EBIP). The coating masked bitterness in the mouth, allowing the release of bitter secoiridoids in the gastrointestinal tract. A cross-over randomised study was performed: twenty healthy subjects consumed at breakfast EBIP (providing 100 mg of secoiridoids) or the control pudding (CP) on two different occasions. Blood samples, glycaemia and appetite ratings were collected at baseline and 30, 60, 120 and 180 min after breakfast. Gastrointestinal peptides, endocannabinoids (EC) and N-acylethanolamines (NAE) were measured in plasma samples. Energy intakes were measured at an ad libitum lunch 3 h after breakfast and over the rest of the day (post lunch) through food diaries. No significant difference in postprandial plasma responses of gastrointestinal hormones, glucose, EC and NAE and of appetite between EBIP and CP was found. However, a trend for a higher response of glucagon-like peptide-1 after EBIP than after CP was observed. EBIP determined a significant 30 % lower energy intake over the post-lunch period compared with CP. These findings were consistent with the tailored release of bitter-tasting compounds from EBIP along the gastrointestinal tract. This study demonstrated that microencapsulated bitter secoiridoids were effective in reducing daily energy intake in humans.

Energy spectrum, dissipation, and spatial structures in reduced Hall magnetohydrodynamic

Energy Technology Data Exchange (ETDEWEB)

Martin, L. N.; Dmitruk, P. [Departamento de Fisica, Facultad de Ciencias Exactas y Naturales, Universidad de Buenos Aires and IFIBA, CONICET, Ciudad Universitaria, 1428 Buenos Aires (Argentina); Gomez, D. O. [Departamento de Fisica, Facultad de Ciencias Exactas y Naturales, Universidad de Buenos Aires and IFIBA, CONICET, Ciudad Universitaria, 1428 Buenos Aires (Argentina); Instituto de Astronomia y Fisica del Espacio, CONICET, Buenos Aires (Argentina)

2012-05-15

We analyze the effect of the Hall term in the magnetohydrodynamic turbulence under a strong externally supported magnetic field, seeing how this changes the energy cascade, the characteristic scales of the flow, and the dynamics of global magnitudes, with particular interest in the dissipation. Numerical simulations of freely evolving three-dimensional reduced magnetohydrodynamics are performed, for different values of the Hall parameter (the ratio of the ion skin depth to the macroscopic scale of the turbulence) controlling the impact of the Hall term. The Hall effect modifies the transfer of energy across scales, slowing down the transfer of energy from the large scales up to the Hall scale (ion skin depth) and carrying faster the energy from the Hall scale to smaller scales. The final outcome is an effective shift of the dissipation scale to larger scales but also a development of smaller scales. Current sheets (fundamental structures for energy dissipation) are affected in two ways by increasing the Hall effect, with a widening but at the same time generating an internal structure within them. In the case where the Hall term is sufficiently intense, the current sheet is fully delocalized. The effect appears to reduce impulsive effects in the flow, making it less intermittent.

Generation and Use of Thermal Energy in the U.S. Industrial Sector and Opportunities to Reduce its Carbon Emissions

Energy Technology Data Exchange (ETDEWEB)

McMillan, Colin [National Renewable Energy Lab. (NREL), Golden, CO (United States); Boardman, Richard [Idaho National Lab. (INL), Idaho Falls, ID (United States); McKellar, Michael [Idaho National Lab. (INL), Idaho Falls, ID (United States); Sabharwall, Piyush [Idaho National Lab. (INL), Idaho Falls, ID (United States); Ruth, Mark [National Renewable Energy Lab. (NREL), Golden, CO (United States); Bragg-Sitton, Shannon [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2016-12-01

This report quantifies greenhouse gas (GHG) emissions from the industrial sector and identifies opportunities for non-GHG-emitting thermal energy sources to replace the most significant GHG-emitting U.S. industries based on targeted, process-level analysis of industrial heat requirements. The intent is to provide a basis for projecting opportunities for clean energy use. This provides a prospectus for small modular nuclear reactors (including nuclear-renewable hybrid energy systems), solar industrial process heat, and geothermal energy. This report provides a complement to analysis of process-efficiency improvement by considering how clean energy delivery and use by industry could reduce GHG emissions.

Renewable and nuclear sources of energy reduce the share of fossil fuels

International Nuclear Information System (INIS)

Koprda, V.

2009-01-01

In this paper author presents a statistical data use of nuclear energy, renewable sources and fossil fuels in the share of energy production in the Slovak Republic. It is stated that use of nuclear energy and renewable sources reduce the share of fossil fuels.

Significantly Elevated Dielectric and Energy Storage Traits in Boron Nitride Filled Polymer Nano-composites with Topological Structure

Science.gov (United States)

Feng, Yefeng; Zhang, Jianxiong; Hu, Jianbing; Li, Shichun; Peng, Cheng

2018-03-01

Interface induced polarization has a prominent influence on dielectric properties of 0-3 type polymer based composites containing Si-based semi-conductors. The disadvantages of composites were higher dielectric loss, lower breakdown strength and energy storage density, although higher permittivity was achieved. In this work, dielectric, conductive, breakdown and energy storage properties of four nano-composites have been researched. Based on the cooperation of fluoropolymer/alpha-SiC layer and fluoropolymer/hexagonal-BN layer, it was confirmed constructing the heterogeneous layer-by-layer composite structure rather than homogeneous mono-layer structure could significantly reduce dielectric loss, promote breakdown strength and increase energy storage density. The former worked for a larger dielectric response and the latter layer acted as a robust barrier of charge carrier transfer. The best nano-composite could possess a permittivity of 43@100 Hz ( 3.3 times of polymer), loss of 0.07@100 Hz ( 37% of polymer), discharged energy density of 2.23 J/cm3@249 kV/cm ( 10 times of polymer) and discharged energy efficiency of 54%@249 kV/cm ( 5 times of polymer). This work might enlighten a facile route to achieve the promising high energy storage composite dielectrics by constructing the layer-by-layer topological structure.

Improving mine-mill water network design by reducing water and energy requirements

Energy Technology Data Exchange (ETDEWEB)

Gunson, A.J.; Klein, B.; Veiga, M. [British Columbia Univ., Vancouver, BC (Canada). Norman B. Keevil Inst. of Mining Engineering

2010-07-01

Mining is an energy-intensive industry, and most processing mills use wet processes to separate minerals from ore. This paper discussed water reduction, reuse and recycling options for a mining and mill operation network. A mine water network design was then proposed in order to identify and reduce water and system energy requirements. This included (1) a description of site water balance, (2) a description of potential water sources, (3) a description of water consumers, (4) the construction of energy requirement matrices, and (5) the use of linear programming to reduce energy requirements. The design was used to determine a site water balance as well as to specify major water consumers during mining and mill processes. Potential water supply combinations, water metering technologies, and recycling options were evaluated in order to identify the most efficient energy and water use combinations. The method was used to highlight potential energy savings from the integration of heating and cooling systems with plant water systems. 43 refs., 4 tabs., 3 figs.

Reducing global NOx emissions: developing advanced energy and transportation technologies.

Science.gov (United States)

Bradley, Michael J; Jones, Brian M

2002-03-01

Globally, energy demand is projected to continue to increase well into the future. As a result, global NOx emissions are projected to continue on an upward trend for the foreseeable future as developing countries increase their standards of living. While the US has experienced improvements in reducing NOx emissions from stationary and mobile sources to reduce ozone, further progress is needed to reduce the health and ecosystem impacts associated with NOx emissions. In other parts of the world, (in developing countries in particular) NOx emissions have been increasing steadily with the growth in demand for electricity and transportation. Advancements in energy and transportation technologies may help avoid this increase in emissions if appropriate policies are implemented. This paper evaluates commercially available power generation and transportation technologies that produce fewer NOx emissions than conventional technologies, and advanced technologies that are on the 10-year commercialization horizon. Various policy approaches will be evaluated which can be implemented on the regional, national and international levels to promote these advanced technologies and ultimately reduce NOx emissions. The concept of the technology leap is offered as a possibility for the developing world to avoid the projected increases in NOx emissions.

New Air Cleaning Strategies for Reduced Commercial Building Ventilation Energy

Energy Technology Data Exchange (ETDEWEB)

Sidheswaran, Meera; Destaillats, Hugo; Sullivan, Douglas P.; Fisk, William J.

2010-10-27

Approximately ten percent of the energy consumed in U.S. commercial buildings is used by HVAC systems to condition outdoor ventilation air. Reducing ventilation rates would be a simple and broadly-applicable energy retrofit option, if practical counter measures were available that maintained acceptable concentrations of indoor-generated air pollutants. The two general categories of countermeasures are: 1) indoor pollutant source control, and 2) air cleaning. Although pollutant source control should be used to the degree possible, source control is complicated by the large number and changing nature of indoor pollutant sources. Particle air cleaning is already routinely applied in commercial buildings. Previous calculations indicate that particle filtration consumes only 10percent to 25percent of the energy that would otherwise be required to achieve an equivalent amount of particle removal with ventilation. If cost-effective air cleaning technologies for volatile organic compounds (VOCs) were also available, outdoor air ventilation rates could be reduced substantially and broadly in the commercial building stock to save energy. The research carried out in this project focuses on developing novel VOC air cleaning technologies needed to enable energy-saving reductions in ventilation rates. The minimum required VOC removal efficiency to counteract a 50percent reduction in ventilation rate for air cleaning systems installed in the HVAC supply airstream is modest (generally 20percent or less).

Holocene reef development where wave energy reduces accommodation

Science.gov (United States)

Grossman, Eric E.; Fletcher, Charles H.

2004-01-01

Analyses of 32 drill cores obtained from the windward reef of Kailua Bay, Oahu, Hawaii, indicate that high wave energy significantly reduced accommodation space for reef development in the Holocene and produced variable architecture because of the combined influence of sea-level history and wave exposure over a complex antecedent topography. A paleostream valley within the late Pleistocene insular limestone shelf provided accommodation space for more than 11 m of vertical accretion since sea level flooded the bay 8000 yr BP. Virtually no net accretion (pile-up of fore-reef-derived rubble (rudstone) and sparse bindstone, and (3) a final stage of catch-up bindstone accretion in depths > 6 m. Coral framestone accreted at rates of 2.5-6.0 mm/yr in water depths > 11 m during the early Holocene; it abruptly terminated at ~4500 yr BP because of wave scour as sea level stabilized. More than 4 m of rudstone derived from the upper fore reef accreted at depths of 6 to 13 m below sea level between 4000 and 1500 yr BP coincident with late Holocene relative sea-level fall. Variations in the thickness, composition, and age of these reef facies across spatial scales of 10-1000 m within Kailua Bay illustrate the importance of antecedent topography and wave-related stress in reducing accommodation space for reef development set by sea level. Although accommodation space of 6 to 17 m has existed through most of the Holocene, the Kailua reef has been unable to catch up to sea level because of persistent high wave stress.

The significance of energy for the economy

International Nuclear Information System (INIS)

Spreng, D.; Schwarz, J.

1993-01-01

The importance of energy for the economy is described here in practical terms. This is meant for the works and workshop manager, maintenance chief, energy specialist, sales staff of industrial and business organisations. The term 'potential for saving energy' is extensively discussed. Statistical research shows a clear connection between energy application and growth of the economy. Fact: a rational use of energy is worth while in many aspects. figs., tabs., 14 refs

Reduced graphene oxide synthesis by high energy ball milling

Energy Technology Data Exchange (ETDEWEB)

Mondal, O. [Department of Physics, M.U.C Women' s College, Burdwan 713104 (India); Mitra, S. [MLS Prof' s Unit, Indian Association for the Cultivation of Science, Kolkata 700032 (India); Pal, M. [CSIR-Central Glass and Ceramic Research Institute, Kolkata 700032 (India); Datta, A. [University School of Basic and Applied Science (USBAS), Guru Gobind Singh Indraprastha University, New Delhi 110075 (India); Dhara, S. [Surface and Nanoscience Division, Indira Gandhi Centre for Atomic Research, Kalpakkam 603102 (India); Chakravorty, D., E-mail: mlsdc@iacs.res.in [MLS Prof' s Unit, Indian Association for the Cultivation of Science, Kolkata 700032 (India)

2015-07-01

Graphene oxide is transformed to reduced graphene oxide by high energy ball milling in inert atmosphere. The process of ball milling introduces defects and removes oxygen functional groups, thereby creating the possibility of fine tuning the band gap of all intermediate stages of the structural evolution. A limit of the backbone sp{sup 2} network structure has been found which should be able to accommodate defects, before amorphization sets in. The amorphization of graphene oxide is achieved rather quickly in comparison to that of graphite. From thermogravimetric and differential scanning calorimetric analysis along with Fourier transform infrared (FTIR) and Raman spectroscopic studies, it is found that the number of oxygen-containing groups decreases at a faster rate than that of aromatic double bonds with increasing ball milling time with a maximum limit of 3 h. Several characterization techniques (FTIR, Raman, UV–Visible and X-ray photoelectron spectroscopy) have confirmed that the material synthesized is, indeed, reduced graphene oxide. - Highlights: • Graphene oxide is transformed to reduced graphene oxide by high energy ball milling in inert atmosphere. • Fine tuning the band gap by introducing defects and removing oxygen functional groups. • Introduction of excess defects leads to amorphization. • Photoluminescence has been observed in the UV-blue region.

Reducing rotor weight

Energy Technology Data Exchange (ETDEWEB)

Cheney, M.C. [PS Enterprises, Inc., Glastonbury, CT (United States)

1997-12-31

The cost of energy for renewables has gained greater significance in recent years due to the drop in price in some competing energy sources, particularly natural gas. In pursuit of lower manufacturing costs for wind turbine systems, work was conducted to explore an innovative rotor designed to reduce weight and cost over conventional rotor systems. Trade-off studies were conducted to measure the influence of number of blades, stiffness, and manufacturing method on COE. The study showed that increasing number of blades at constant solidity significantly reduced rotor weight and that manufacturing the blades using pultrusion technology produced the lowest cost per pound. Under contracts with the National Renewable Energy Laboratory and the California Energy Commission, a 400 kW (33m diameter) turbine was designed employing this technology. The project included tests of an 80 kW (15.5m diameter) dynamically scaled rotor which demonstrated the viability of the design.

Estimation of energy saving thanks to a reduced-model-based approach: Example of bread baking by jet impingement

International Nuclear Information System (INIS)

Alamir, M.; Witrant, E.; Della Valle, G.; Rouaud, O.; Josset, Ch.; Boillereaux, L.

2013-01-01

In this paper, a reduced order mechanistic model is proposed for the evolution of temperature and humidity during French bread baking. The model parameters are identified using experimental data. The resulting model is then used to estimate the potential energy saving that can be obtained using jet impingement technology when used to increase the heat transfer efficiency. Results show up to 16% potential energy saving under certain assumptions. - Highlights: ► We developed a mechanistic model of heat and mass transfer in bread including different and multiple energy sources. ► An optimal control system permits to track references trajectories with a minimization of energy consuming. ► The methodology is evaluated with jet impingement technique. ► Results show a significant energy saving of about 17% of energy with reasonable actuator variations

Think Green: Teach Students Smart Ways to Reduce Home Energy Use

Science.gov (United States)

Roman, Harry T.

2008-01-01

Energy conservation and reducing heat loss in buildings is a very powerful way to lower energy costs. Sometimes great savings can be realized with simple measures. This subject provides a great vehicle for teaching science content that is very relevant to everyone's daily life--and financial well-being. In this article, the author first discusses…

Significantly reduced c-axis thermal diffusivity of graphene-based papers

Science.gov (United States)

Han, Meng; Xie, Yangsu; Liu, Jing; Zhang, Jingchao; Wang, Xinwei

2018-06-01

Owing to their very high thermal conductivity as well as large surface-to-volume ratio, graphene-based films/papers have been proposed as promising candidates of lightweight thermal interface materials and lateral heat spreaders. In this work, we study the cross-plane (c-axis) thermal conductivity (k c ) and diffusivity (α c ) of two typical graphene-based papers, which are partially reduced graphene paper (PRGP) and graphene oxide paper (GOP), and compare their thermal properties with highly-reduced graphene paper and graphite. The determined α c of PRGP varies from (1.02 ± 0.09) × 10‑7 m2 s‑1 at 295 K to (2.31 ± 0.18) × 10‑7 m2 s‑1 at 12 K. This low α c is mainly attributed to the strong phonon scattering at the grain boundaries and defect centers due to the small grain sizes and high-level defects. For GOP, α c varies from (1.52 ± 0.05) × 10‑7 m2 s‑1 at 295 K to (2.28 ± 0.08) × 10‑7 m2 s‑1 at 12.5 K. The cross-plane thermal transport of GOP is attributed to the high density of functional groups between carbon layers which provide weak thermal transport tunnels across the layers in the absence of direct energy coupling among layers. This work sheds light on the understanding and optimizing of nanostructure of graphene-based paper-like materials for desired thermal performance.

Reduced energy density of close-up diets decrease ruminal pH and increase concentration of volatile fatty acids postpartum in Holstein cows.

Science.gov (United States)

Huang, Wenming; Tian, Yujia; Li, Shengli; Wu, Zhaohai; Cao, Zhijun

2017-11-01

The objective of this study was to determine the effect of reduced energy density of close-up diets on ruminal fermentation parameters in transition cows. Fourteen Holstein dry cows were blocked and assigned randomly to three groups fed a high energy density diet (HD, 1.62 Mcal of net energy for lactation (NE L )/kg dry matter (DM)), or a middle energy density diet (MD, 1.47 Mcal NE L /kg DM), or a low energy density diet (LD, 1.30 Mcal NE L /kg DM) prepartum, and were fed the same diet postpartum. The reduced energy density diets decreased the average dry matter intake (DMI) prepartum and tended to increase the DMI postpartum. The ruminal pH of the LD group was significantly higher prepartum and lower during the first week of lactation compared with the other two groups. The reduced energy density diet depressed the average ruminal concentration of propionate and butyrate prepartum, and increased the average concentration of total volatile fatty acids (VFA) postpartum. The LD group had higher populations of Butyrivibrio fibrisolvens and Ruminococcus flavefaciens relative to HD and MD groups on 7 days in milk. In conclusion, the cows fed reduced energy density diet prepartum had higher VFA concentration, but were more susceptible to subacute ruminal acidosis postpartum. © 2017 Japanese Society of Animal Science.

Passive Method to Reduce Solar Energy Effect on the Cooling Load in Buildings

Directory of Open Access Journals (Sweden)

Orfi J.

2012-10-01

Full Text Available Energy needed for cooling residential and industrial buildings in hot weather countries is the major issue. The period needed for cooling or comfort conditions in those countries exceeds five months and outdoor temperature reaches more than 40 °C. Also, the solar intensity usually high and can reach about one kW per m2. Hence, any attempt to reduce the effect of solar energy on the cooling load is worthy to investigate. The present work analyzes using artificial, naturally ventilated, shading covers to reduce the effect of solar energy. Analytical and numerical analyzes were performed on the effect of adding a ventilated cover to walls and roof exposed to the solar energy.

The Role of Cellars in Reducing Energy Consumption in the Residential Architecture of Iran

Directory of Open Access Journals (Sweden)

Hossein Soltanzadeh

2015-03-01

Full Text Available According to research, between 15 to 20 percent of the total energy consumption of every country is used for residential spaces. This amount is explanatory of the high cost and will follow the destruction of natural resources and environmental demolition. The aim of this research is to recognize earth thermal ability and its usage in public buildings and especially in private buildings in order to reduce energy consumption which can lead to huge savings in natural resources. It is intended to pay attention to the role of cellars as underground spaces in reducing energy consumption in residential spaces in this research. Cellars which are one of the climatic elements were very useful in residential spaces in the past and underground spaces in cities and public spaces are using in the contemporary era. Native Iranian architecture has exclusive features in residential spaces. One of the reducing energy consumption techniques is using ground depth and underground spaces in private and public buildings. Pit gardens, Shovadan, aqueducts, lavers, cellars with natural abilities in coldness, warmness and support are examples of underground space uses (providing cooling, heating and storing food and goods in Iranian cities. The Main questions of this research are: what the role of undergrounds or cellars was in native Iranian architecture and how impressionable it was in reducing energy consumption. The theoretical framework of this study indicates that several factors had positive impacts on reducing energy consumption in cellars. To do this research, descriptive-analytical methods were uses and were analyzed according to case studies in Qazvin houses. The results of this study reveal that cellars had a main role in human thermal comfort and they caused reducing energy consumption in residential and even public spaces. Also, several factors such as the cellar's depth, height and dimensions had impacts on the reduction amount of energy consumption and the

China's numerical management system for reducing national energy intensity

International Nuclear Information System (INIS)

Li, Huimin; Zhao, Xiaofan; Yu, Yuqing; Wu, Tong; Qi, Ye

2016-01-01

In China, the national target for energy intensity reduction, when integrated with target disaggregation and information feedback systems, constitutes a numerical management system, which is a hallmark of modern governance. This paper points out the technical weaknesses of China's current numerical management system. In the process of target disaggregation, the national target cannot be fully disaggregated to local governments, sectors and enterprises without omissions. At the same time, governments at lower levels face pressure for reducing energy intensity that exceeds their respective jurisdictions. In the process of information feedback, information failure is inevitable due to statistical inaccuracy. Furthermore, the monitoring system is unable to correct all errors, and data verification plays a limited role in the examination system. To address these problems, we recommend that the government: use total energy consumption as the primary indicator of energy management; reform the accounting and reporting of energy statistics toward greater consistency, timeliness and transparency; clearly define the responsibility of the higher levels of government. - Highlights: •We assess drawbacks of China's numerical management system for energy intensity. •The national energy intensity target cannot be fully disaggregated without omissions. •Data distortion is due to failures in statistics, monitoring and examination system. •Lower-level governments’ ability to meet energy target is weaker than their pressure. •We provide three policy recommendations for China's policy-makers.

Psychological strategies to reduce energy consumption: project summary report

Energy Technology Data Exchange (ETDEWEB)

Becker, L J; Seligman, C; Darley, J M

1979-06-30

This report reviews the research conducted in connection with a project to apply psychological theory and procedures to the problems of encouraging residential energy conservation. A major part of the project involved surveys of residents' energy-related attitudes. The best (and only consistent) attitudinal predictor of residents' actual energy consumption was their attitude about thermal comfort. A number of other attitudes that could conceivably have been related to consumption, such as attitudes about the reality of the crisis, were not found to be related to consumption. Another major focus of the project was on the effectiveness of feedback (that is, giving residents information about their energy use) as an aid to residents' conservation efforts. A series of experiments demonstrated that frequent, credible energy-consumption feedback, coupled with encouragement to adopt a reasonable but difficult energy-conservation goal, could facilitate conservation. However, these studies also demonstrated that residents could not be given just any kind of information about their energy use as feedback and that even proper feedback would not lead to conservation in all households. Conditions that are crucial for the success of feedback as a conservation aid are discussed. Other studies conducted by the project looked at the effect on energy consumption of (1) a device to reduce air-conditioning waste by signalling when it is cool outside, (2) an automatic multi-setback thermostat, and (3) utility companies' average payment plans. A survey of residents' knowledge of their energy use also was conducted. 23 references.

Energy deposition and the formation of biologically significant lesions by accelerated ions

International Nuclear Information System (INIS)

Kiefer, J.

1985-01-01

The assumption that the number of biologically significant lesions depends only on the amount of of energy absorbed in a critical cellular site is not able to explain the increase of RBE with LET and leads to large discrepancies between predicted and measured inactivation cross sections in the LET range between 20 and 200 keV.μm -1 . It has, therefore, to be concluded that not only the amount of energy absorbed but also the spatial pattern of this deposition plays a decisive role. In the model presented it is postulated that two or more energy deposition events in nanometre sites are required for the formation of biologically significant lesions. This cooperative action has to take place in very short times so that only interactions within a single particle track contribute. The mathematical treatment will be outlined and qualitatively shown that the model is able to predict RBE-LET relationships. The calculations use a track structure model based on classical collision mechanics. It is compared with existing experimental results showing good agreement at least for higher particle energies. (author)

Energy crops as a strategy for reducing greenhouse gas emissions

International Nuclear Information System (INIS)

Olesen, J.E.

2002-01-01

Miscanthus harvested in April resulted in an emission reduction of 447 kt CO 2 eq yr -1 , growing Miscanthus for harvest in November gave a reduction of 355 kt CO 2 eq yr -1 , and growing triticale gave a reduction of 265 kt CO 2 eq yr -1 . Hence, taking nitrous oxide emissions, C sequestration and energy use into account slightly reduced the value of triticale, but significantly increased the value of Miscanthus as a CO 2 mitigation option. (au)

The potential for energy savings when reducing the water consumption in a kraft pulp mill

Energy Technology Data Exchange (ETDEWEB)

Wising, Ulrika; Berntsson, Thore [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Chemical Engineering and Environmental Science; Stuart, Paul [Ecole Polytechnique, Montreal (Canada). Dept. of Chemical Engineering

2004-05-01

In this paper an existing pulp and paper mill has been studied in a systematic way regarding the reduction of water consumption, and the resulting increased potential for energy integration. It has been found that when the mill's hot water consumption is decreased, the live steam demand for the mill also decreases. Also when decreasing the hot water consumption, the quantity and temperature of available excess heat increases. This excess heat can be used for evaporation, thereby reducing the live steam demand further by up to 1.5 GJ/t. A pinch analysis was performed at an existing mill and it was found that if pinch violations are removed, the hot water consumption is not an important factor any more. Removing all the pinch violations and using the remaining excess heat for evaporation yields a significantly larger energy savings for the mill (4.0 GJ/t). From an economic optimum perspective it is probably most profitable to do a combination of reducing water consumption, removing pinch violations, and use the remaining excess heat for evaporation.

Male circumcision significantly reduces prevalence and load of genital anaerobic bacteria.

Science.gov (United States)

Liu, Cindy M; Hungate, Bruce A; Tobian, Aaron A R; Serwadda, David; Ravel, Jacques; Lester, Richard; Kigozi, Godfrey; Aziz, Maliha; Galiwango, Ronald M; Nalugoda, Fred; Contente-Cuomo, Tania L; Wawer, Maria J; Keim, Paul; Gray, Ronald H; Price, Lance B

2013-04-16

Male circumcision reduces female-to-male HIV transmission. Hypothesized mechanisms for this protective effect include decreased HIV target cell recruitment and activation due to changes in the penis microbiome. We compared the coronal sulcus microbiota of men from a group of uncircumcised controls (n = 77) and from a circumcised intervention group (n = 79) at enrollment and year 1 follow-up in a randomized circumcision trial in Rakai, Uganda. We characterized microbiota using16S rRNA gene-based quantitative PCR (qPCR) and pyrosequencing, log response ratio (LRR), Bayesian classification, nonmetric multidimensional scaling (nMDS), and permutational multivariate analysis of variance (PerMANOVA). At baseline, men in both study arms had comparable coronal sulcus microbiota; however, by year 1, circumcision decreased the total bacterial load and reduced microbiota biodiversity. Specifically, the prevalence and absolute abundance of 12 anaerobic bacterial taxa decreased significantly in the circumcised men. While aerobic bacterial taxa also increased postcircumcision, these gains were minor. The reduction in anaerobes may partly account for the effects of circumcision on reduced HIV acquisition. The bacterial changes identified in this study may play an important role in the HIV risk reduction conferred by male circumcision. Decreasing the load of specific anaerobes could reduce HIV target cell recruitment to the foreskin. Understanding the mechanisms that underlie the benefits of male circumcision could help to identify new intervention strategies for decreasing HIV transmission, applicable to populations with high HIV prevalence where male circumcision is culturally less acceptable.

Considerations for reducing food system energy demand while scaling up urban agriculture

Science.gov (United States)

Mohareb, Eugene; Heller, Martin; Novak, Paige; Goldstein, Benjamin; Fonoll, Xavier; Raskin, Lutgarde

2017-12-01

There is an increasing global interest in scaling up urban agriculture (UA) in its various forms, from private gardens to sophisticated commercial operations. Much of this interest is in the spirit of environmental protection, with reduced waste and transportation energy highlighted as some of the proposed benefits of UA; however, explicit consideration of energy and resource requirements needs to be made in order to realize these anticipated environmental benefits. A literature review is undertaken here to provide new insight into the energy implications of scaling up UA in cities in high-income countries, considering UA classification, direct/indirect energy pressures, and interactions with other components of the food-energy-water nexus. This is followed by an exploration of ways in which these cities can plan for the exploitation of waste flows for resource-efficient UA. Given that it is estimated that the food system contributes nearly 15% of total US energy demand, optimization of resource use in food production, distribution, consumption, and waste systems may have a significant energy impact. There are limited data available that quantify resource demand implications directly associated with UA systems, highlighting that the literature is not yet sufficiently robust to make universal claims on benefits. This letter explores energy demand from conventional resource inputs, various production systems, water/energy trade-offs, alternative irrigation, packaging materials, and transportation/supply chains to shed light on UA-focused research needs. By analyzing data and cases from the existing literature, we propose that gains in energy efficiency could be realized through the co-location of UA operations with waste streams (e.g. heat, CO2, greywater, wastewater, compost), potentially increasing yields and offsetting life cycle energy demands relative to conventional approaches. This begs a number of energy-focused UA research questions that explore the

Motor Challenge: Improving Efficiency of Tube Drawing Bench Reduces Energy Use by 34%

International Nuclear Information System (INIS)

Erika Ericksen

1999-01-01

The case study reveals how a manufacturer of high-precision, small-diameter steel tubing has reduced energy consumption and realized considerable electrical, labor, and materials cost savings with a more energy-efficient motor

Methods for Reducing the Energy Consumption of Mobile Broadband Networks

DEFF Research Database (Denmark)

Micallef, Gilbert

2010-01-01

Up until recently, very little consideration has been given towards reducing the energy consumption of the networks supporting mobile communication. This has now become an important issue since with the predicted boost in traffic, network operators are required to upgrade and extend their networks......, increasing also their overall energy consumption. However, traffic analysis shows that during a 24 hour period, the volume of carried traffic varies continuously, with the network operating anywhere close to its full capacity for very short periods of time. The problem is that during hours of low network...... traffic the energy consumption remains high. This article proposes two major solutions for mitigating this problem. In the first case, an energy saving between 14% and 36% is observed by allowing the network to dynamically optimize its available capacity based on the traffic being carried. In the second...

Mussel-inspired Fluoro-Polydopamine Functionalization of Titanium Dioxide Nanowires for Polymer Nanocomposites with Significantly Enhanced Energy Storage Capability

Science.gov (United States)

Wang, Guanyao; Huang, Xingyi; Jiang, Pingkai

2017-01-01

High-dielectric-constant polymer nanocomposites are demonstrated to show great promise as energy storage materials. However, the large electrical mismatch and incompatibility between nanofillers and polymer matrix usually give rise to significantly reduced breakdown strength and weak energy storage capability. Therefore, rational selection and elaborate functionalization of nanofillers to optimize the performance of polymer nanocomposites are vital. Herein, inspired by adhesive proteins in mussels, a facile modification by fluoro-polydopamine is employed to reinforce the compatibility of TiO2 nanowires in the fluoropolymer matrix. The loading of 2.5 vol % f-DOPA@TiO2 NWs leads to an ultrahigh discharged energy density of 11.48 J cm−3 at 530 MV m−1, more than three times of commercial biaxial-oriented polypropylene (BOPP, 3.56 J cm−3 at 600 MV m−1). A gratifying high energy density of 9.12 J cm−3 has also been obtained with nanofiller loading as high as 15 vol % at 360 MV m−1, which is nearly double to that of pure P(VDF-HFP) (4.76 J cm−3 at 360 MV m−1). This splendid energy storage capability seems to rival or exceed most of previously reported nano-TiO2 based nanocomposites. The methods presented here provide deep insights into the design of polymer nanocomposites for energy storage applications. PMID:28225047

Mussel-inspired Fluoro-Polydopamine Functionalization of Titanium Dioxide Nanowires for Polymer Nanocomposites with Significantly Enhanced Energy Storage Capability

Science.gov (United States)

Wang, Guanyao; Huang, Xingyi; Jiang, Pingkai

2017-02-01

High-dielectric-constant polymer nanocomposites are demonstrated to show great promise as energy storage materials. However, the large electrical mismatch and incompatibility between nanofillers and polymer matrix usually give rise to significantly reduced breakdown strength and weak energy storage capability. Therefore, rational selection and elaborate functionalization of nanofillers to optimize the performance of polymer nanocomposites are vital. Herein, inspired by adhesive proteins in mussels, a facile modification by fluoro-polydopamine is employed to reinforce the compatibility of TiO2 nanowires in the fluoropolymer matrix. The loading of 2.5 vol % f-DOPA@TiO2 NWs leads to an ultrahigh discharged energy density of 11.48 J cm-3 at 530 MV m-1, more than three times of commercial biaxial-oriented polypropylene (BOPP, 3.56 J cm-3 at 600 MV m-1). A gratifying high energy density of 9.12 J cm-3 has also been obtained with nanofiller loading as high as 15 vol % at 360 MV m-1, which is nearly double to that of pure P(VDF-HFP) (4.76 J cm-3 at 360 MV m-1). This splendid energy storage capability seems to rival or exceed most of previously reported nano-TiO2 based nanocomposites. The methods presented here provide deep insights into the design of polymer nanocomposites for energy storage applications.

Quilting after mastectomy significantly reduces seroma formation

African Journals Online (AJOL)

reduce or prevent seroma formation among mastectomy patients ... of this prospective study is to evaluate the effect of surgical quilting ... Seroma was more common in smokers (p=0.003) and was not decreased by the .... explain its aetiology.

The energetic significance of cooking.

Science.gov (United States)

Carmody, Rachel N; Wrangham, Richard W

2009-10-01

While cooking has long been argued to improve the diet, the nature of the improvement has not been well defined. As a result, the evolutionary significance of cooking has variously been proposed as being substantial or relatively trivial. In this paper, we evaluate the hypothesis that an important and consistent effect of cooking food is a rise in its net energy value. The pathways by which cooking influences net energy value differ for starch, protein, and lipid, and we therefore consider plant and animal foods separately. Evidence of compromised physiological performance among individuals on raw diets supports the hypothesis that cooked diets tend to provide energy. Mechanisms contributing to energy being gained from cooking include increased digestibility of starch and protein, reduced costs of digestion for cooked versus raw meat, and reduced energetic costs of detoxification and defence against pathogens. If cooking consistently improves the energetic value of foods through such mechanisms, its evolutionary impact depends partly on the relative energetic benefits of non-thermal processing methods used prior to cooking. We suggest that if non-thermal processing methods such as pounding were used by Lower Palaeolithic Homo, they likely provided an important increase in energy gain over unprocessed raw diets. However, cooking has critical effects not easily achievable by non-thermal processing, including the relatively complete gelatinisation of starch, efficient denaturing of proteins, and killing of food borne pathogens. This means that however sophisticated the non-thermal processing methods were, cooking would have conferred incremental energetic benefits. While much remains to be discovered, we conclude that the adoption of cooking would have led to an important rise in energy availability. For this reason, we predict that cooking had substantial evolutionary significance.

A Bit String Content Aware Chunking Strategy for Reduced CPU Energy on Cloud Storage

Directory of Open Access Journals (Sweden)

Bin Zhou

2015-01-01

Full Text Available In order to achieve energy saving and reduce the total cost of ownership, green storage has become the first priority for data center. Detecting and deleting the redundant data are the key factors to the reduction of the energy consumption of CPU, while high performance stable chunking strategy provides the groundwork for detecting redundant data. The existing chunking algorithm greatly reduces the system performance when confronted with big data and it wastes a lot of energy. Factors affecting the chunking performance are analyzed and discussed in the paper and a new fingerprint signature calculation is implemented. Furthermore, a Bit String Content Aware Chunking Strategy (BCCS is put forward. This strategy reduces the cost of signature computation in chunking process to improve the system performance and cuts down the energy consumption of the cloud storage data center. On the basis of relevant test scenarios and test data of this paper, the advantages of the chunking strategy are verified.

Electric power and its significance as the energy for innovation and progress

International Nuclear Information System (INIS)

Klinger, H.; Boehmer, T.

1999-01-01

The significance of electric power as the essential form of energy to support innovation and progress well into the future is explained with respect to four major domains of application: 1. Innovative activities in microelectronics and semiconductor technology, for applications such as automation and computer technology, instrumentation and control technology, facility and systems management and control. 2. Energy efficiency programmes and schemes for increasing the penetration of energiy from renewable sources in the market. Example: Heat pump technology. 3. Electric power as an energy boosting innovation in industrial production processes. Examples are given from the transportation sector. (orig./CB) [de

Reduce energy use and greenhouse gas emissions from global dairy processing facilities

Energy Technology Data Exchange (ETDEWEB)

Xu Tengfang, E-mail: ttxu@lbl.go [International Energy Studies Group, Environmental Energy Technologies Division, Lawrence Berkeley National Laboratory, 1 Cyclotron Road, Berkeley, CA 94720 (United States); Flapper, Joris [International Energy Studies Group, Environmental Energy Technologies Division, Lawrence Berkeley National Laboratory, 1 Cyclotron Road, Berkeley, CA 94720 (United States); Centre for Energy and Environmental Studies, University of Groningen, IVEM, Nijenborgh 4, 9747, AG Groningen (Netherlands)

2011-01-15

Global butter, concentrated milk, and milk powder products use approximately 15% of annual raw milk production. Similar to cheese and fluid milk, dairy processing of these products can be energy intensive. In this paper, we analyzed production and energy data compiled through extensive literature reviews on butter, concentrated milk, milk and whey powder processing across various countries and plants. Magnitudes of national final and primary specific energy consumption (SEC) exhibited large variations across dairy products; in addition, the final SEC of individual plants and products exhibited significant variations within a country and between countries. Furthermore, we quantified national energy intensity indicators (EIIs) accounting for dairy product mixes and technological advancement. The significant variations of SEC and EII values indicate a high degree of likelihood that there is significant potential for energy savings in the global dairy processing industry. Based upon the study samples, we estimate potential energy savings for dairy processing industry in selected countries, and estimates annual reduction of 9-14 million metric-ton carbon-equivalent could be achieved if measures are implemented to lower SEC values by 50-80% in half of global dairy plants. The paper calls for publication of more energy data from the dairy processing industry. - Research highlights: {yields} The specific energy consumption exhibited large variations across dairy products, plants, and countries. {yields} National energy intensity indicators also exhibited significant variations. {yields} There is a large global potential for energy savings and carbon reduction in dairy processing plants. {yields} The paper calls for publication of more energy data from the dairy processing industry.

Retrofitting Inefficient Rooftop Air-Conditioning Units Reduces U.S. Navy Energy Use (Fact Sheet)

Energy Technology Data Exchange (ETDEWEB)

None, None

2014-04-01

As part of the U.S. Navy's overall energy strategy, the National Renewable Energy Laboratory (NREL) partnered with the Naval Facilities Engineering Command (NAVFAC) to demonstrate market-ready energy efficiency measures, renewable energy generation, and energy systems integration. One such technology - retrofitting rooftop air-conditioning units with an advanced rooftop control system - was identified as a promising source for reducing energy use and costs, and can contribute to increasing energy security.

Reducing Energy Demand Using Wheel-Individual Electric Drives to Substitute EPS-Systems

Directory of Open Access Journals (Sweden)

Jürgen Römer

2018-01-01

Full Text Available The energy demand of vehicles is influenced, not only by the drive systems, but also by a number of add-on systems. Electric vehicles must satisfy this energy demand completely from the battery. Hence, the use of power steering systems directly result in a range reduction. The “e2-Lenk” joint project funded by the German Federal Ministry of Education and Research (BMBF involves a novel steering concept for electric vehicles to integrate the function of steering assistance into the drive-train. Specific distribution of driving torque at the steered axle allows the steering wheel torque to be influenced to support the steering force. This provides a potential for complete substitution of conventional power steering systems and reduces the vehicle’s energy demand. This paper shows the potential of wheel-individual drives influencing the driver’s steering torque using a control technique based on classical EPS control plans. Compared to conventional power-assisted steering systems, a reduced energy demand becomes evident over a wide range of operating conditions.

The Carbon and Global Warming Potential Impacts of Organic Farming: Does It Have a Significant Role in an Energy Constrained World?

Directory of Open Access Journals (Sweden)

Ralph C. Martin

2011-01-01

Full Text Available About 130 studies were analyzed to compare farm-level energy use and global warming potential (GWP of organic and conventional production sectors. Cross cutting issues such as tillage, compost, soil carbon sequestration and energy offsets were also reviewed. Finally, we contrasted E and GWP data from the wider food system. We concluded that the evidence strongly favours organic farming with respect to whole-farm energy use and energy efficiency both on a per hectare and per farm product basis, with the possible exception of poultry and fruit sectors. For GWP, evidence is insufficient except in a few sectors, with results per ha more consistently favouring organic farming than GWP per unit product. Tillage was consistently a negligible contributor to farm E use and additional tillage on organic farms does not appear to significantly deplete soil C. Energy offsets, biogas, energy crops and residues have a more limited role on organic farms compared to conventional ones, because of the nutrient and soil building uses of soil organic matter, and the high demand for organic foods in human markets. If farm E use represents 35% of total food chain E use, improvements shown of 20% or more in E efficiency through organic farm management would reduce food-chain E use by 7% or more. Among other food supply chain stages, wholesale/retail (including cooling and packaging and processing often each contribute 30% or more to total food system E. Thus, additional improvements can be obtained with reduced processing, whole foods and food waste minimization.

Significant thermal energy reduction in lactic acid production process

International Nuclear Information System (INIS)

Mujtaba, Iqbal M.; Edreder, Elmahboub A.; Emtir, Mansour

2012-01-01

Lactic acid is widely used as a raw material for the production of biodegradable polymers and in food, chemical and pharmaceutical industries. The global market for lactic acid is expected to reach 259 thousand metric tons by the year 2012. For batch production of lactic acid, the traditional process includes the following steps: (i) esterification of impure lactic acid with methanol in a batch reactor to obtain methyl lactate (ester), (ii) separation of the ester in a batch distillation, (iii) hydrolysis of the ester with water in a batch reactor to produce lactic acid and (iv) separation of lactic acid (in high purity) in a batch distillation. Batch reactive distillation combines the benefit of both batch reactor and batch distillation and enhances conversion and productivity (Taylor and Krishna, 2000 ; Mujtaba and Macchietto, 1997 ). Therefore, the first and the last two steps of the lactic acid production process can be combined together in batch reactive distillation () processes. However, distillation (batch or continuous) is an energy intensive process and consumes large amount of thermal energy (via steam). This paper highlights how significant (over 50%) reduction in thermal energy consumption can be achieved for lactic acid production process by carefully controlling the reflux ratio but without compromising the product specification. In this paper, only the simultaneous hydrolysis of methyl lactate ester and the separation of lactic acid using batch reactive distillation is considered.

Using passive cooling strategies to improve thermal performance and reduce energy consumption of residential buildings in U.A.E. buildings

Directory of Open Access Journals (Sweden)

Hanan M. Taleb

2014-06-01

Full Text Available Passive design responds to local climate and site conditions in order to maximise the comfort and health of building users while minimising energy use. The key to designing a passive building is to take best advantage of the local climate. Passive cooling refers to any technologies or design features adopted to reduce the temperature of buildings without the need for power consumption. Consequently, the aim of this study is to test the usefulness of applying selected passive cooling strategies to improve thermal performance and to reduce energy consumption of residential buildings in hot arid climate settings, namely Dubai, United Arab Emirates. One case building was selected and eight passive cooling strategies were applied. Energy simulation software – namely IES – was used to assess the performance of the building. Solar shading performance was also assessed using Sun Cast Analysis, as a part of the IES software. Energy reduction was achieved due to both the harnessing of natural ventilation and the minimising of heat gain in line with applying good shading devices alongside the use of double glazing. Additionally, green roofing proved its potential by acting as an effective roof insulation. The study revealed several significant findings including that the total annual energy consumption of a residential building in Dubai may be reduced by up to 23.6% when a building uses passive cooling strategies.

Hypothalamic over-expression of VGF in the Siberian hamster increases energy expenditure and reduces body weight gain.

Science.gov (United States)

Lewis, Jo E; Brameld, John M; Hill, Phil; Cocco, Cristina; Noli, Barbara; Ferri, Gian-Luca; Barrett, Perry; Ebling, Francis J P; Jethwa, Preeti H

2017-01-01

VGF (non-acronymic) was first highlighted to have a role in energy homeostasis through experiments involving dietary manipulation in mice. Fasting increased VGF mRNA in the Arc and levels were subsequently reduced upon refeeding. This anabolic role for VGF was supported by observations in a VGF null (VGF-/-) mouse and in the diet-induced and gold-thioglucose obese mice. However, this anabolic role for VGF has not been supported by a number of subsequent studies investigating the physiological effects of VGF-derived peptides. Intracerebroventricular (ICV) infusion of TLQP-21 increased resting energy expenditure and rectal temperature in mice and protected against diet-induced obesity. Similarly, ICV infusion of TLQP-21 into Siberian hamsters significantly reduced body weight, but this was due to a decrease in food intake, with no effect on energy expenditure. Subsequently NERP-2 was shown to increase food intake in rats via the orexin system, suggesting opposing roles for these VGF-derived peptides. Thus to further elucidate the role of hypothalamic VGF in the regulation of energy homeostasis we utilised a recombinant adeno-associated viral vector to over-express VGF in adult male Siberian hamsters, thus avoiding any developmental effects or associated functional compensation. Initially, hypothalamic over-expression of VGF in adult Siberian hamsters produced no effect on metabolic parameters, but by 12 weeks post-infusion hamsters had increased oxygen consumption and a tendency to increased carbon dioxide production; this attenuated body weight gain, reduced interscapular white adipose tissue and resulted in a compensatory increase in food intake. These observed changes in energy expenditure and food intake were associated with an increase in the hypothalamic contents of the VGF-derived peptides AQEE, TLQP and NERP-2. The complex phenotype of the VGF-/- mice is a likely consequence of global ablation of the gene and its derived peptides during development, as well

IMPROVING ENERGY EFFICIENCY AND REDUCING COSTS IN THE DRINKING WATER SUPPLY INDUSTRY: An ENERGY STAR Resource Guide for Energy and Plant Managers

Energy Technology Data Exchange (ETDEWEB)

Melody, Moya; Dunham Whitehead, Camilla; Brown, Richard

2010-09-30

As American drinking water agencies face higher production costs, demand, and energy prices, they seek opportunities to reduce costs without negatively affecting the quality of the water they deliver. This guide describes resources for cost-effectively improving the energy efficiency of U.S. public drinking water facilities. The guide (1) describes areas of opportunity for improving energy efficiency in drinking water facilities; (2) provides detailed descriptions of resources to consult for each area of opportunity; (3) offers supplementary suggestions and information for the area; and (4) presents illustrative case studies, including analysis of cost-effectiveness.

Energy Management Systems to Reduce Electrical Energy Consumption

OpenAIRE

Oriti, Giovanna

2015-01-01

EXECUTIVE SUMMARY An energy management system comprises an electrical energy storage element such as a battery, renewable electrical energy sources such as solar and wind, a digital signal processing controller and a solid state power converter to interface the elements together. This hardware demonstration in the lab at the Naval Postgraduate School will focus on solid state power conversion methods to improve the reliability and efficiency of electrical energy consumption by Navy facilit...

Performances of low-dose dual-energy CT in reducing artifacts from implanted metallic orthopedic devices

Energy Technology Data Exchange (ETDEWEB)

Filograna, Laura [Catholic University of Rome, School of Medicine, University Hospital ' ' A. Gemelli' ' , Department of Radiological Sciences, Institute of Radiology, Rome (Italy); University of Zurich, Department of Forensic Medicine and Imaging, Institute of Forensic Medicine, Zurich (Switzerland); Magarelli, Nicola; Leone, Antonio; Bonomo, Lorenzo [Catholic University of Rome, School of Medicine, University Hospital ' ' A. Gemelli' ' , Department of Radiological Sciences, Institute of Radiology, Rome (Italy); De Waure, Chiara; Calabro, Giovanna Elisa [Catholic University of Rome, School of Medicine, University Hospital ' ' A. Gemelli' ' , Research Centre for Health Technology Assessment, Department of Public Health, Section of Hygiene, Rome (Italy); Finkenstaedt, Tim [University Hospital Zurich, Institute of Diagnostic and Interventional Radiology, Zurich (Switzerland); Thali, Michael John [University of Zurich, Department of Forensic Medicine and Imaging, Institute of Forensic Medicine, Zurich (Switzerland)

2016-07-15

The objective was to evaluate the performances of dose-reduced dual-energy computed tomography (DECT) in decreasing metallic artifacts from orthopedic devices compared with dose-neutral DECT, dose-neutral single-energy computed tomography (SECT), and dose-reduced SECT. Thirty implants in 20 consecutive cadavers underwent both SECT and DECT at three fixed CT dose indexes (CTDI): 20.0, 10.0, and 5.0 mGy. Extrapolated monoenergetic DECT images at 64, 69, 88, 105, 120, and 130 keV, and individually adjusted monoenergy for optimized image quality (OPTkeV) were generated. In each group, the image quality of the seven monoenergetic images and of the SECT image was assessed qualitatively and quantitatively by visually rating and by measuring the maximum streak artifact respectively. The comparison between SECT and OPTkeV evaluated overall within all groups showed a significant difference (p <0.001), with OPTkeV images providing better images. Comparing OPTkeV with the other DECT images, a significant difference was shown (p <0.001), with OPTkeV and 130-keV images providing the qualitatively best results. The OPTkeV images of 5.0-mGy acquisitions provided percentages of images with scores 1 and 2 of 36 % and 30 % respectively, compared with 0 % and 33.3 % of the corresponding SECT images of 10- and 20-mGy acquisitions. Moreover, DECT reconstructions at the OPTkeV of the low-dose group showed higher CT numbers than the SECT images of dose groups 1 and 2. This study demonstrates that low-dose DECT permits a reduction of artifacts due to metallic implants to be obtained in a similar manner to neutral-dose DECT and better than reduced or neutral-dose SECT. (orig.)

Finding of no significant impact for the joint DOE/EPA program on national industrial competitiveness through energy efficiency and economics (NICE{sup 3})

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The Department of Energy (DOE) has prepared a Programmatic Environmental Assessment (PEA), to assess the environment impacts associated with a joint DOE/EPA cost-sharing grant program named National Industrial Competitiveness through Energy Efficiency, Environment and Economics (NICE{sup 3}). The purpose of the NICE{sup 3} Program is to encourage waste minimization technology in industry by funding projects that develop activities and process improvements to conserve energy and reduce pollution. The proposed action would provide Federal financial assistance in the form of grants to industry in order to promote pollution prevention, energy efficiency, and cost competitiveness. Based on the analysis presented in the PEA, DOE has determined that the proposed action (providing NICE{sup 3} grants for projects which are consistent with the goals of the PPA and EPACT) does not constitute a major Federal action significantly affecting the quality of the human environment within the meaning of NEPA. Therefore, the preparation of an Environmental Impact Statement is not needed and the Department is issuing this Finding of No Significant Impact.

If Canada is serious about reducing greenhouse gases, we need nuclear energy

International Nuclear Information System (INIS)

Lemieux, C.

2003-01-01

Canada's energy options are reviewed in light of the need to find practical solutions to supply the nation's growing demand for power, coupled with equally pressing need to reduce greenhouse gas emissions to meet Kyoto commitments, and to do so without costing Canadians jobs and economic disaster. Among the options available - renewable, hydro, fossil fuels, nuclear -- nuclear power is identified as the only one that promises to meet the growing demand for power without the practical, economic and environmental disadvantages associated with the alternatives. Based on Canadian experience with nuclear power in the past, it is pointed out that between 1971 and 2000 Canada , by using nuclear fuel , has averted the production of 32 million tonnes of acid gases, millions of tonnes of other pollutants and well over a billion tonnes of carbon dioxide, while producing only 14 per cent of its energy requirements from nuclear fuel The principal argument made is that given our position as the world's leading supplier of uranium to electric utilities, the safety record of our CANDU reactors , and the fact that nuclear power is one of the cleanest large-scale energy source, nuclear power has the potential to make significant contribution to Canada's ability to meet its future energy requirements, and achieve the GHG emission reduction targets imposed by the Kyoto Agreement, without causing serious harm to the economy. The author goes as far as to say that without serious consideration being given to nuclear power, Canada has no chance even to come close to its Kyoto greenhouse emission targets without disastrous consequences to the economy. (author)

Reduced-order modeling of piezoelectric energy harvesters with nonlinear circuits under complex conditions

Science.gov (United States)

Xiang, Hong-Jun; Zhang, Zhi-Wei; Shi, Zhi-Fei; Li, Hong

2018-04-01

A fully coupled modeling approach is developed for piezoelectric energy harvesters in this work based on the use of available robust finite element packages and efficient reducing order modeling techniques. At first, the harvester is modeled using finite element packages. The dynamic equilibrium equations of harvesters are rebuilt by extracting system matrices from the finite element model using built-in commands without any additional tools. A Krylov subspace-based scheme is then applied to obtain a reduced-order model for improving simulation efficiency but preserving the key features of harvesters. Co-simulation of the reduced-order model with nonlinear energy harvesting circuits is achieved in a system level. Several examples in both cases of harmonic response and transient response analysis are conducted to validate the present approach. The proposed approach allows to improve the simulation efficiency by several orders of magnitude. Moreover, the parameters used in the equivalent circuit model can be conveniently obtained by the proposed eigenvector-based model order reduction technique. More importantly, this work establishes a methodology for modeling of piezoelectric energy harvesters with any complicated mechanical geometries and nonlinear circuits. The input load may be more complex also. The method can be employed by harvester designers to optimal mechanical structures or by circuit designers to develop novel energy harvesting circuits.

Nonlinear image blending for dual-energy MDCT of the abdomen: can image quality be preserved if the contrast medium dose is reduced?

Science.gov (United States)

Mileto, Achille; Ramirez-Giraldo, Juan Carlos; Marin, Daniele; Alfaro-Cordoba, Marcela; Eusemann, Christian D; Scribano, Emanuele; Blandino, Alfredo; Mazziotti, Silvio; Ascenti, Giorgio

2014-10-01

The objective of this study was to compare the image quality of a dual-energy nonlinear image blending technique at reduced load of contrast medium with a simulated 120-kVp linear blending technique at a full dose during portal venous phase MDCT of the abdomen. Forty-five patients (25 men, 20 women; mean age, 65.6 ± 9.7 [SD] years; mean body weight, 74.9 ± 12.4 kg) underwent contrast-enhanced single-phase dual-energy CT of the abdomen by a random assignment to one of three different contrast medium (iomeprol 400) dose injection protocols: 1.3, 1.0, or 0.65 mL/kg of body weight. The contrast-to-noise ratio (CNR) and noise at the portal vein, liver, aorta, and kidney were compared among the different datasets using the ANOVA. Three readers qualitatively assessed all datasets in a blinded and independent fashion. Nonlinear blended images at a 25% reduced dose allowed a significant improvement in CNR (p < 0.05 for all comparisons), compared with simulated 120-kVp linear blended images at a full dose. No statistically significant difference existed in CNR and noise between the nonlinear blended images at a 50% reduced dose and the simulated 120-kVp linear blended images at a full dose. Nonlinear blended images at a 50% reduced dose were considered in all cases to have acceptable image quality. The dual-energy nonlinear image blending technique allows reducing the dose of contrast medium up to 50% during portal venous phase imaging of the abdomen while preserving image quality.

Daily exposure to either a high- or low-energy-dense snack food reduces its reinforcing value in adolescents.

Science.gov (United States)

Temple, Jennifer L; Van der Kloet, Erika; Atkins, Amanda M; Crandall, Amanda K; Ziegler, Amanda M

2017-02-01

To examine the impact of daily exposure to a low-energy-dense (LED) or a high-energy-dense (HED) snack food on its reinforcing value (RRV) in adolescents with healthy weight, overweight, or obesity. A parallel-group, randomized trial was used to assess RRV of LED or HED snack food at baseline and again after exposure to that snack food daily for 2 weeks in 77 adolescents, aged 13 to 17 years. Information on eating-related subject characteristics was also collected at baseline. After 2 weeks of daily exposure, the RRV of the snack foods was significantly reduced in all participants, regardless of energy density or participant weight status. Among individuals who were high in dietary restraint only, those randomized to LED food found their snack food less reinforcing at baseline than those who were randomized to HED food. Baseline eating-related variables also differed as a function of weight status. Daily exposure to snack food in adolescents reduces the RRV of that food regardless of snack food energy density or weight status of the adolescent. This finding differs from adults, suggesting that increases in RRV of HED food after repeated exposure may develop after adolescence. © 2017 The Obesity Society.

Defibrillator charging before rhythm analysis significantly reduces hands-off time during resuscitation

DEFF Research Database (Denmark)

Hansen, L. K.; Folkestad, L.; Brabrand, M.

2013-01-01

BACKGROUND: Our objective was to reduce hands-off time during cardiopulmonary resuscitation as increased hands-off time leads to higher mortality. METHODS: The European Resuscitation Council (ERC) 2005 and ERC 2010 guidelines were compared with an alternative sequence (ALT). Pulseless ventricular...... physicians were included. All had prior experience in advanced life support. Chest compressions were shorter interrupted using ALT (mean, 6.7 vs 13.0 seconds). Analyzing data for ventricular tachycardia scenarios only, hands-off time was shorter using ALT (mean, 7.1 vs 18.2 seconds). In ERC 2010 vs ALT, 12...... physicians were included. Two physicians had not prior experience in advanced life support. Hands-off time was reduced using ALT (mean, 3.9 vs 5.6 seconds). Looking solely at ventricular tachycardia scenarios, hands-off time was shortened using ALT (mean, 4.5 vs 7.6 seconds). No significant reduction...

Pulmonary arterial hypertension reduces energy efficiency of right, but not left, rat ventricular trabeculae.

Science.gov (United States)

Pham, Toan; Nisbet, Linley; Taberner, Andrew; Loiselle, Denis; Han, June-Chiew

2018-04-01

Pulmonary arterial hypertension (PAH) triggers right ventricle (RV) hypertrophy and left ventricle (LV) atrophy, which progressively leads to heart failure. We designed experiments under conditions mimicking those encountered by the heart in vivo that allowed us to investigate whether consequent structural and functional remodelling of the ventricles affects their respective energy efficiencies. We found that peak work output was lower in RV trabeculae from PAH rats due to reduced extent and velocity of shortening. However, their suprabasal enthalpy was unaffected due to increased activation heat, resulting in reduced suprabasal efficiency. There was no effect of PAH on LV suprabasal efficiency. We conclude that the mechanism underlying the reduced energy efficiency of hypertrophied RV tissues is attributable to the increased energy cost of Ca 2+ cycling, whereas atrophied LV tissues still maintain normal mechano-energetic performance. Pulmonary arterial hypertension (PAH) greatly increases the afterload on the right ventricle (RV), triggering RV hypertrophy, which progressively leads to RV failure. In contrast, the disease reduces the passive filling pressure of the left ventricle (LV), resulting in LV atrophy. We investigated whether these distinct structural and functional consequences to the ventricles affect their respective energy efficiencies. We studied trabeculae isolated from both ventricles of Wistar rats with monocrotaline-induced PAH and their respective Control groups. Trabeculae were mounted in a calorimeter at 37°C. While contracting at 5 Hz, they were subjected to stress-length work-loops over a wide range of afterloads. They were subsequently required to undergo a series of isometric contractions at various muscle lengths. In both protocols, stress production, length change and suprabasal heat output were simultaneously measured. We found that RV trabeculae from PAH rats generated higher activation heat, but developed normal active stress. Their

Impacts of Using Distributed Energy Resources to Reduce Peak Loads in Vermont

Energy Technology Data Exchange (ETDEWEB)

Ruth, Mark F. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Lunacek, Monte S. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Jones, Birk [Univ. of New Mexico, Albuquerque, NM (United States); Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-11-28

To help the United States develop a modern electricity grid that provides reliable power from multiple resources as well as resiliency under extreme conditions, the U.S. Department of Energy (DOE) is leading the Grid Modernization Initiative (GMI) to help shape the future of the nation's grid. Under the GMI, DOE funded the Vermont Regional Initiative project to provide the technical support and analysis to utilities that need to mitigate possible impacts of increasing renewable generation required by statewide goals. Advanced control of distributed energy resources (DER) can both support higher penetrations of renewable energy by balancing controllable loads to wind and photovoltaic (PV) solar generation and reduce peak demand by shedding noncritical loads. This work focuses on the latter. This document reports on an experiment that evaluated and quantified the potential benefits and impacts of reducing the peak load through demand response (DR) using centrally controllable electric water heaters (EWHs) and batteries on two Green Mountain Power (GMP) feeders. The experiment simulated various hypothetical scenarios that varied the number of controllable EWHs, the amount of distributed PV systems, and the number of distributed residential batteries. The control schemes were designed with several objectives. For the first objective, the primary simulations focused on reducing the load during the independent system operator (ISO) peak when capacity charges were the primary concern. The second objective was to mitigate DR rebound to avoid new peak loads and high ramp rates. The final objective was to minimize customers' discomfort, which is defined by the lack of hot water when it is needed. We performed the simulations using the National Renewable Energy Laboratory's (NREL's) Integrated Energy System Model (IESM) because it can simulate both electric power distribution feeder and appliance end use performance and it includes the ability to simulate

Enzyme Supplementation of Broiler Feeds with Reduced Mineral and Energy Levels

Directory of Open Access Journals (Sweden)

JO Nunes

2015-12-01

Full Text Available ABSTRACT An experiment was conducted with the purpose of evaluating enzyme blends on the performance, carcass traits, and bone mineralization of broilers. In total, 928 one-day-old Cobb 500 male chicks of were used. A completely randomized design with four treatments with eight replicates of 29 birds each was adopted. The evaluated treatments were: 1- Positive Control (PC, feed containing the nutritional recommendations of the genetic company's manual; 2- Negative Control (NC, feed with reductions of 75 kcal/kg AME and 0.10 and 0.12 percent points of phosphorus and calcium, respectively; 3 - NC + enzyme blend (amylase + b-glucanase, xylanase, and phytase; 250 g/t of feed and 4 - NC + enzyme complex (phytase, amylase, xylanase, glucanase, pectinase, cellulase, and protease; 200 g/t of feed. Birds fed the diet with reduced nutrient levels (NC presented the worst performance (p0.05 carcass or parts yields. The broilers fed the reduced-nutrient and energy diet presented lower (p<0.05 tibial ash, calcium, and phosphorus contents that the other treatments. The use of enzyme combinations improved the performance of broilers fed diets with reduced nutrient and energy levels.

Spring-like Ankle Foot Orthoses reduce the energy cost of walking by taking over ankle work

NARCIS (Netherlands)

Bregman, D.J.J.; Harlaar, J.; Meskers, C.G.M.; de Groot, V.

2012-01-01

In patients with central neurological disorders, gait is often limited by a reduced ability to push off with the ankle. To overcome this reduced ankle push-off, energy-storing, spring-like carbon-composite Ankle Foot Orthoses (AFO) can be prescribed. It is expected that the energy returned by the

Heat storage in forest biomass significantly improves energy balance closure particularly during stable conditions

Science.gov (United States)

Lindroth, A.; Mölder, M.; Lagergren, F.

2009-08-01

Temperature measurements in trunks and branches in a mature ca. 100 years-old mixed pine and spruce forest in central Sweden were used to estimate the heat storage in the tree biomass. The estimated heat flux in the sample trees and data on biomass distributions were used to scale up to stand level biomass heat fluxes. The rate of change of sensible and latent heat storage in the air layer below the level of the flux measurements was estimated from air temperature and humidity profile measurements and soil heat flux was estimated from heat flux plates and soil temperature measurements. The fluxes of sensible and latent heat from the forest were measured with an eddy covariance system in a tower. The analysis was made for a two-month period in summer of 1995. The tree biomass heat flux was the largest of the estimated storage components and varied between 40 and -35 W m-2 on summer days with nice weather. Averaged over two months the diurnal maximum of total heat storage was 45 W m-2 and the minimum was -35 W m-2. The soil heat flux and the sensible heat storage in air were out of phase with the biomass flux and they reached maximum values that were about 75% of the maximum of the tree biomass heat storage. The energy balance closure improved significantly when the total heat storage was added to the turbulent fluxes. The slope of a regression line with sum of fluxes and storage as independent and net radiation as dependent variable, increased from 0.86 to 0.95 for half-hourly data and the scatter was also reduced. The most significant finding was, however, that during nights with strongly stable conditions when the sensible heat flux dropped to nearly zero, the total storage matched the net radiation nearly perfectly. Another interesting result was that the mean energy imbalance started to increase when the Richardson number became more negative than ca. -0.1. In fact, the largest energy deficit occurred at maximum instability. Our conclusion is that eddy

Supplemental Perioperative Oxygen to Reduce Surgical Site Infection after High Energy Fracture Surgery

Science.gov (United States)

2017-10-01

AWARD NUMBER: W81XWH-12-1-0588 TITLE: Supplemental Perioperative Oxygen to Reduce Surgical Site Infection after High- Energy Fracture Surgery...High- Energy Fracture Surgery 5a. CONTRACT NUMBER W81XWH-12-1-0588 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Robert V. O’Toole, MD...14 4 1. INTRODUCTION: The overall scope of this project is to address the treatment of high- energy military fractures, which has

If Canada is serious about reducing greenhouse gases, we need nuclear energy

Energy Technology Data Exchange (ETDEWEB)

Lemieux, C.

2003-07-01

Canada's energy options are reviewed in light of the need to find practical solutions to supply the nation's growing demand for power, coupled with equally pressing need to reduce greenhouse gas emissions to meet Kyoto commitments, and to do so without costing Canadians jobs and economic disaster. Among the options available -- renewable, hydro, fossil fuels, nuclear -- nuclear power is identified as the only one that promises to meet the growing demand for power without the practical, economic and environmental disadvantages associated with the alternatives. Based on Canadian experience with nuclear power in the past, it is pointed out that between 1971 and 2000 Canada, by using nuclear fuel, has averted the production of 32 million tonnes of acid gases, millions of tonnes of other pollutants and well over a billion tonnes of carbon dioxide, while producing only 14 per cent of its energy requirements from nuclear fuel. The principal argument made is that given our position as the world's leading supplier of uranium to electric utilities, the safety record of our CANDU reactors, and the fact that nuclear power is one of the cleanest large-scale energy source, nuclear power has the potential to make significant contribution to Canada's ability to meet its future energy requirements, and achieve the GHG emission reduction targets imposed by the Kyoto Agreement, without causing serious harm to the economy. The author goes as far as to say that without serious consideration being given to nuclear power, Canada has no chance even to come close to its Kyoto greenhouse emission targets without disastrous consequences to the economy.

Reduce energy use and greenhouse gas emissions from global dairy processing facilities

Energy Technology Data Exchange (ETDEWEB)

Xu, Tengfang [International Energy Studies Group, Environmental Energy Technologies Division, Lawrence Berkeley National Laboratory, 1 Cyclotron Road, Berkeley, CA 94720 (United States); Flapper, Joris [International Energy Studies Group, Environmental Energy Technologies Division, Lawrence Berkeley National Laboratory, 1 Cyclotron Road, Berkeley, CA 94720 (United States); Centre for Energy and Environmental Studies, University of Groningen, IVEM, Nijenborgh 4, 9747, AG Groningen (Netherlands)

2011-01-15

Global butter, concentrated milk, and milk powder products use approximately 15% of annual raw milk production. Similar to cheese and fluid milk, dairy processing of these products can be energy intensive. In this paper, we analyzed production and energy data compiled through extensive literature reviews on butter, concentrated milk, milk and whey powder processing across various countries and plants. Magnitudes of national final and primary specific energy consumption (SEC) exhibited large variations across dairy products; in addition, the final SEC of individual plants and products exhibited significant variations within a country and between countries. Furthermore, we quantified national energy intensity indicators (EIIs) accounting for dairy product mixes and technological advancement. The significant variations of SEC and EII values indicate a high degree of likelihood that there is significant potential for energy savings in the global dairy processing industry. Based upon the study samples, we estimate potential energy savings for dairy processing industry in selected countries, and estimates annual reduction of 9-14 million metric-ton carbon-equivalent could be achieved if measures are implemented to lower SEC values by 50-80% in half of global dairy plants. The paper calls for publication of more energy data from the dairy processing industry. (author)

Reducing the operational energy demand in buildings using building information modeling tools and sustainability approaches

Directory of Open Access Journals (Sweden)

Mojtaba Valinejad Shoubi

2015-03-01

Full Text Available A sustainable building is constructed of materials that could decrease environmental impacts, such as energy usage, during the lifecycle of the building. Building Information Modeling (BIM has been identified as an effective tool for building performance analysis virtually in the design stage. The main aims of this study were to assess various combinations of materials using BIM and identify alternative, sustainable solutions to reduce operational energy consumption. The amount of energy consumed by a double story bungalow house in Johor, Malaysia, and assessments of alternative material configurations to determine the best energy performance were evaluated by using Revit Architecture 2012 and Autodesk Ecotect Analysis software to show which of the materials helped in reducing the operational energy use of the building to the greatest extent throughout its annual life cycle. At the end, some alternative, sustainable designs in terms of energy savings have been suggested.

Energy efficiency through energy audit

International Nuclear Information System (INIS)

Esan, A. A.

2000-08-01

Energy is an essential factor to economic and social development and improved standards of living in developing countries. Nigeria in particular. There is a strong need for greater energy efficiency in every sector of economy in order to reduce costs. enhance competitiveness, conserve energy resources and reduce environmental impacts associated with production, distribution and use of energy. Energy auditing and monitoring has a significant role in any energy management and conservation project. Energy auditing as an important part of industrial energy management on plant level, represents a complex of activities aiming at the efficient use of energy. The activities are undertaken by a team of experts who use a set of measuring instruments to monitor and evaluate all the necessary data to elaborate a package of recommendations on improvements in the field of energy efficiency and possible product quality. The inefficient conversion and use of energy have been identified as a central problem for all developing countries, Nigeria inclusive, since they all consume significantly higher amounts of energy per unit of GDP than OECD countries. This aggravates energy-related environmental problems and is also a burden on domestic resources and foreign exchange. Energy prices have risen drastically in many developing countries, while energy intensities remain high. Price changes alone are not rapidly translating energy efficiency improvements. Identifying and removing the obstacles to greater energy efficiency should be priority for government in developing countries. This is why the Energy Commission, an apex organ of government on Energy matters in all its ramifications is out to encourage relatively low-cost energy audits for the Textile industries - such audits can identify ''good house-keeping's' measures, such as simply process improvements, that reduce energy consumption and operating costs. This will be followed by the training of plant workers/energy managers

Sodium-Reduced Meat and Poultry Products Contain a Significant Amount of Potassium from Food Additives.

Science.gov (United States)

Parpia, Arti Sharma; Goldstein, Marc B; Arcand, JoAnne; Cho, France; L'Abbé, Mary R; Darling, Pauline B

2018-05-01

counterparts (mean difference [95% CI]: 486 [334-638]; Padditives appearing on the product label ingredient list, did not significantly differ between the two groups. Potassium additives are frequently added to sodium-reduced MPPs in amounts that significantly contribute to the potassium load for patients with impaired renal handling of potassium caused by chronic kidney disease and certain medications. Patients requiring potassium restriction should be counseled to be cautious regarding the potassium content of sodium-reduced MPPs and encouraged to make food choices accordingly. Copyright © 2018 Academy of Nutrition and Dietetics. Published by Elsevier Inc. All rights reserved.

The Value of CO2-Geothermal Bulk Energy Storage to Reducing CO2 Emissions Compared to Conventional Bulk Energy Storage Technologies

Science.gov (United States)

Ogland-Hand, J.; Bielicki, J. M.; Buscheck, T. A.

2016-12-01

Sedimentary basin geothermal resources and CO2 that is captured from large point sources can be used for bulk energy storage (BES) in order to accommodate higher penetration and utilization of variable renewable energy resources. Excess energy is stored by pressurizing and injecting CO2 into deep, porous, and permeable aquifers that are ubiquitous throughout the United States. When electricity demand exceeds supply, some of the pressurized and geothermally-heated CO2 can be produced and used to generate electricity. This CO2-BES approach reduces CO2 emissions directly by storing CO2 and indirectly by using some of that CO2 to time-shift over-generation and displace CO2 emissions from fossil-fueled power plants that would have otherwise provided electricity. As such, CO2-BES may create more value to regional electricity systems than conventional pumped hydro energy storage (PHES) or compressed air energy storage (CAES) approaches that may only create value by time-shifting energy and indirectly reducing CO2 emissions. We developed and implemented a method to estimate the value that BES has to reducing CO2 emissions from regional electricity systems. The method minimizes the dispatch of electricity system components to meet exogenous demand subject to various CO2 prices, so that the value of CO2 emissions reductions can be estimated. We applied this method to estimate the performance and value of CO2-BES, PHES, and CAES within real data for electricity systems in California and Texas over the course of a full year to account for seasonal fluctuations in electricity demand and variable renewable resource availability. Our results suggest that the value of CO2-BES to reducing CO2 emissions may be as much as twice that of PHES or CAES and thus CO2-BES may be a more favorable approach to energy storage in regional electricity systems, especially those where the topography is not amenable to PHES or the subsurface is not amenable to CAES.

FLUKA simulations of a moderated reduced weight high energy neutron detection system

Energy Technology Data Exchange (ETDEWEB)

Biju, K., E-mail: bijusivolli@gmail.com [Health Physics Division, Bhabha Atomic Research Centre, Mumbai 400085 (India); Tripathy, S.P.; Sunil, C.; Sarkar, P.K. [Health Physics Division, Bhabha Atomic Research Centre, Mumbai 400085 (India)

2012-08-01

Neutron response of the systems containing high density polyethylene (HDPE) spheres coupled with different external metallic converters has been studied using the FLUKA Monte Carlo simulation code. A diameter of 17.8 cm (7 in.) of the moderating sphere is found to be optimum to obtain the maximum response when used with the neutron converter shells like W, Pb and Zr. Enhancement ratios of the neutron response due to the induced (n, xn) reactions in the outer converters made of W, Pb and Zr are analyzed. It is observed that the enhancement in the response by 1 cm thick Zr shell is comparable to that of 1 cm thick Pb in the energy region of 10-50 MeV. An appreciable enhancement is observed in the case of Zr converter for the higher energy neutrons. Thus, by reducing the dimension of the moderating sphere and using a Zr converter shell, the weight of the system reduces to 10 kg which is less compared to the presently available extended high energy neutron rem meters. The normalized energy dependent ambient dose equivalent response of the zirconium based rem counter (ZReC) at high energies is found to be in good agreement with the energy differential H{sup Low-Asterisk }(10) values suggested by the International Commission on Radiological Protection (ICRP). Based on this study, it is proposed that a rem meter made of 17.8 cm diameter HDPE sphere with 1 cm thick Zr can be used effectively and conveniently for routine monitoring in the accelerator environment.

Exchanging and Storing Energy. Reducing Energy Demand through Heat Exchange between Functions and Temporary Storage

Energy Technology Data Exchange (ETDEWEB)

Sillem, E.

2011-06-15

As typical office buildings from the nineties have large heating and cooling installations to provide heat or cold wherever and whenever needed, more recent office buildings have almost no demand for heating due to high internal heat loads caused by people, lighting and office appliances and because of the great thermal qualities of the contemporary building envelope. However, these buildings still have vast cooling units to cool down servers and other energy consuming installations. At the same time other functions such as dwellings, swimming pools, sporting facilities, archives and museums still need to be heated most of the year. In the current building market there is an increasing demand for mixed-use buildings or so called hybrid buildings. The Science Business Centre is no different and houses a conference centre, offices, a museum, archives, an exhibition space and a restaurant. From the initial program brief it seemed that the building will simultaneously house functions that need cooling most of the year and functions that will need to be heated the majority of the year. Can this building be equipped with a 'micro heating and cooling network' and where necessary temporarily store energy? With this idea a research proposal was formulated. How can the demand for heating and cooling of the Science Business Centre be reduced by using energy exchange between different kinds of functions and by temporarily storing energy? In conclusion the research led to: four optimized installation concepts; short term energy storage in pavilion concept and museum; energy exchange between the restaurant and archives; energy exchange between the server space and the offices; the majority of heat and cold will be extracted from the soil (long term energy storage); the access heat will be generated by the energy roof; PV cells from the energy roof power all climate installations; a total energy plan for the Science Business Centre; a systematic approach for exchanging

A feasibility study of microgrids for reducing energy use and GHG emissions in an industrial application

International Nuclear Information System (INIS)

Li, Mengyu; Zhang, Xiongwen; Li, Guojun; Jiang, Chaoyang

2016-01-01

Highlights: • A life cycle assessment is conducted on the microgrids for an industry application. • The effect of renewable energy on the LCA performances of microgrids is illustrated. • The minimal life cycle energy use and GHG emissions of microgrids are evaluated. • The LCA of different pathways for electricity, heat and hydrogen are presented. - Abstract: Microgrids provide a new energy paradigm with the benefits of higher energy supply reliability, lower greenhouse gas (GHG) emissions through a higher penetration of renewable sources, higher energy efficiencies through the use of local waste heat and the avoidance of losses in transmission and distribution. This study reports a life cycle assessment (LCA) of microgrids for an industry application of an ammonia plant in central Inner Mongolia, China. The life cycle energy use and GHG emissions of the microgrids are evaluated and compared to the existing fossil fuel-based energy system. The electricity, heat and hydrogen fuel loads of the ammonia plant are all modelled in the study. An optimization model is developed to estimate the minimum life cycle energy use and GHG emissions with the microgrids under three scenarios (natural gas (NG)-based, optimized, and maximum renewable energy microgrids). The results indicate that the use of wind and solar in the NG-based microgrid can only slightly reduce the energy use and GHG emissions. If there are no land area limitations on the deployment of solar and wind power, the maximum renewable energy microgrid offers significant reductions of fossil fuel energy of up to 56.9% and GHG emissions reductions of up to 66.3% compared to the existing energy system.

A chimpanzee recognizes synthetic speech with significantly reduced acoustic cues to phonetic content.

Science.gov (United States)

Heimbauer, Lisa A; Beran, Michael J; Owren, Michael J

2011-07-26

A long-standing debate concerns whether humans are specialized for speech perception, which some researchers argue is demonstrated by the ability to understand synthetic speech with significantly reduced acoustic cues to phonetic content. We tested a chimpanzee (Pan troglodytes) that recognizes 128 spoken words, asking whether she could understand such speech. Three experiments presented 48 individual words, with the animal selecting a corresponding visuographic symbol from among four alternatives. Experiment 1 tested spectrally reduced, noise-vocoded (NV) synthesis, originally developed to simulate input received by human cochlear-implant users. Experiment 2 tested "impossibly unspeechlike" sine-wave (SW) synthesis, which reduces speech to just three moving tones. Although receiving only intermittent and noncontingent reward, the chimpanzee performed well above chance level, including when hearing synthetic versions for the first time. Recognition of SW words was least accurate but improved in experiment 3 when natural words in the same session were rewarded. The chimpanzee was more accurate with NV than SW versions, as were 32 human participants hearing these items. The chimpanzee's ability to spontaneously recognize acoustically reduced synthetic words suggests that experience rather than specialization is critical for speech-perception capabilities that some have suggested are uniquely human. Copyright © 2011 Elsevier Ltd. All rights reserved.

Denton, Texas: Using Transportation Data to Reduce Fuel Consumption (City Energy: From Data to Decisions)

Energy Technology Data Exchange (ETDEWEB)

Office of Strategic Programs, Strategic Priorities and Impact Analysis Team

2017-09-29

This fact sheet "Denton, Texas: Using Transportation Data to Reduce Fuel Consumption" explains how the City of Denton used data from the U.S. Department of Energy's Cities Leading through Energy Analysis and Planning (Cities-LEAP) and the State and Local Energy Data (SLED) programs to inform its city energy planning. It is one of ten fact sheets in the "City Energy: From Data to Decisions" series.

Intensity-modulated radiotherapy significantly reduces xerostomia compared with conventional radiotherapy

International Nuclear Information System (INIS)

Braam, Petra M.; Terhaard, Chris H.J. M.D.; Roesink, Judith M.; Raaijmakers, Cornelis P.J.

2006-01-01

Purpose: Xerostomia is a severe complication after radiotherapy for oropharyngeal cancer, as the salivary glands are in close proximity with the primary tumor. Intensity-modulated radiotherapy (IMRT) offers theoretical advantages for normal tissue sparing. A Phase II study was conducted to determine the value of IMRT for salivary output preservation compared with conventional radiotherapy (CRT). Methods and Materials: A total of 56 patients with oropharyngeal cancer were prospectively evaluated. Of these, 30 patients were treated with IMRT and 26 with CRT. Stimulated parotid salivary flow was measured before, 6 weeks, and 6 months after treatment. A complication was defined as a stimulated parotid flow rate <25% of the preradiotherapy flow rate. Results: The mean dose to the parotid glands was 48.1 Gy (SD 14 Gy) for CRT and 33.7 Gy (SD 10 Gy) for IMRT (p < 0.005). The mean parotid flow ratio 6 weeks and 6 months after treatment was respectively 41% and 64% for IMRT and respectively 11% and 18% for CRT. As a result, 6 weeks after treatment, the number of parotid flow complications was significantly lower after IMRT (55%) than after CRT (87%) (p = 0.002). The number of complications 6 months after treatment was 56% for IMRT and 81% for CRT (p = 0.04). Conclusions: IMRT significantly reduces the number of parotid flow complications for patients with oropharyngeal cancer

Measuring the Efficacy of an Energy and Environmental Awareness Campaign to Effectively Reduce Water Consumption

Science.gov (United States)

Miller, Laura Little

2010-01-01

Increased energy costs and a move toward environmental stewardship are driving many organizations, including universities, to engage in awareness efforts to reduce both energy consumption and their carbon footprint. The purpose of this paper is to determine whether organizational programs aimed at energy and environmental awareness have a…

Experimental Evaluation of Simple Thermal Storage Control Strategies in Low-Energy Solar Houses to Reduce Electricity Consumption during Grid On-Peak Periods

Directory of Open Access Journals (Sweden)

Kyoung-Ho Lee

2015-08-01

Full Text Available There is growing interest in zero-energy and low-energy buildings, which have a net energy consumption (on an annual basis of almost zero. Because they can generate both electricity and thermal energy through the use of solar photovoltaic (PV and solar thermal collectors, and with the help of reduced building thermal demand, low-energy buildings can not only make a significant contribution to energy conservation on an annual basis, but also reduce energy consumption and peak demand. This study focused on electricity consumption during the on-peak period in a low-energy residential solar building and considers the use of a building’s thermal mass and thermal storage to reduce electricity consumption in summer and winter by modulation of temperature setpoints for heat pump and indoor thermostats in summer and additional use of a solar heating loop in winter. Experiments were performed at a low-energy solar demonstration house that has solar collectors, hot water storage, a ground-coupled heat pump, and a thermal storage tank. It was assumed that the on-peak periods were from 2 pm to 5 pm on hot summer days and from 5 pm to 8 pm on cold winter days. To evaluate the potential for utilizing the building’s thermal storage capacity in space cooling and heating, the use of simple control strategies on three test days in summer and two test days in the early spring were compared in terms of net electricity consumption and peak demand, which also considered the electricity generation from solar PV modules on the roof of the house.

Potential for reducing GHG emissions and energy consumption from implementing the aluminum intensive vehicle fleet in China

International Nuclear Information System (INIS)

Du, J.D.; Han, W.J.; Peng, Y.H.; Gu, C.C.

2010-01-01

The automobile industry in China has rapidly developed in recent years which resulted in an increase in gasoline usage and greenhouse gas (GHG) emissions. Focus on climate change has also accelerated to grow pressure on reducing vehicle weight and improving fuel efficiency. Aluminum (Al) as a light metal has demonstrated a great potential for weight savings in applications such as engine blocks, cylinder heads, wheels, hoods, tailgates etc. However, primary Al production requires intensive energy and the cost of Al is more than traditional steel, which may affect the total benefits realized from using Al in automobiles. Therefore, it is very essential to conduct a study to quantify the life cycle GHG emissions and energy consumption if the plan is to achieve fleet-wide Al intensive vehicles. This paper describes a life cycle assessment (LCA) methodology and the general modeling assumptions used to evaluate the impact of Al intensive vehicle on GHG emissions and energy consumption. The results indicated that the reductions in life cycle GHG emissions and energy consumption were not significant when the maximum Al content in an automobile is 145 kg, which is the average level of Al usage in automobiles in North America. A neural network methodology was used to forecast the vehicle stock in China from 2010 to 2020 and a vehicle fleet model was established to track GHG emissions and energy consumption of the vehicle fleet. A material availability factor was also introduced into the LCA methodology to further assist decision makers in providing rational proposals for a widespread implementation of Al in automobiles. A sensitivity analysis was also conducted to study the impact of the Al content in a vehicle on the final outcomes. The GHG emissions and energy consumption could be further reduced when the Al content in an automobile increases.

A Pathway to Reduce Energy Consumption in the Thermal Stabilization Process of Carbon Fiber Production

Directory of Open Access Journals (Sweden)

Srinivas Nunna

2018-05-01

Full Text Available Process parameters, especially in the thermal stabilization of polyacrylonitrile (PAN fibers, play a critical role in controlling the cost and properties of the resultant carbon fibers. This study aimed to efficiently handle the energy expense areas during carbon fiber manufacturing without reducing the quality of carbon fibers. We introduced a new parameter (recirculation fan frequency in the stabilization stage and studied its influence on the evolution of the structure and properties of fibers. Initially, the progress of the cyclization reaction in the fiber cross-sections with respect to fan frequencies (35, 45, and 60 Hz during stabilization was analyzed using the Australian Synchrotron-high resolution infrared imaging technique. A parabolic trend in the evolution of cyclic structures was observed in the fiber cross-sections during the initial stages of stabilization; however, it was transformed to a uniform trend at the end of stabilization for all fan frequencies. Simultaneously, the microstructure and property variations at each stage of manufacturing were assessed. We identified nominal structural variations with respect to fan frequencies in the intermediate stages of thermal stabilization, which were reduced during the carbonization process. No statistically significant variations were observed between the tensile properties of fibers. These observations suggested that, when using a lower fan frequency (35 Hz, it was possible to manufacture carbon fibers with a similar performance to those produced using a higher fan frequency (60 Hz. As a result, this study provided an opportunity to reduce the energy consumption during carbon fiber manufacturing.

Variational minimization of atomic and molecular ground-state energies via the two-particle reduced density matrix

International Nuclear Information System (INIS)

Mazziotti, David A.

2002-01-01

Atomic and molecular ground-state energies are variationally determined by constraining the two-particle reduced density matrix (2-RDM) to satisfy positivity conditions. Because each positivity condition corresponds to correcting the ground-state energies for a class of Hamiltonians with two-particle interactions, these conditions collectively provide a new approach to many-body theory that, unlike perturbation theory, can capture significantly correlated phenomena including the multireference effects of potential-energy surfaces. The D, Q, and G conditions for the 2-RDM are extended through generalized lifting operators inspired from the formal solution of N-representability. These lifted conditions agree with the hierarchy of positivity conditions presented by Mazziotti and Erdahl [Phys. Rev. A 63, 042113 (2001)]. The connection between positivity and the formal solution explains how constraining higher RDMs to be positive semidefinite improves the N representability of the 2-RDM and suggests using pieces of higher positivity conditions that computationally scale like the D condition. With the D, Q, and G conditions as well as pieces of higher positivity the electronic energies for Be, LiH, H 2 O, and BH are computed through a primal-dual interior-point algorithm for positive semidefinite programming. The variational method produces potential-energy surfaces that are highly accurate even far from the equilibrium geometry where single-reference perturbation-based methods often fail to produce realistic energies

Applying Smart Grid Technology For Reducing Electric Energy Consumption

Energy Technology Data Exchange (ETDEWEB)

Hoffman, Roy

2010-09-15

In recent years the term 'Smart Grid' has become a widely used buzz word with respect to the operation of Electric Power Systems. One analysis has suggested that a Smart Grid could potentially reduce annual energy consumption in the USA by 56 to 203 billion kWh in 2030, corresponding to a 1.2 to 4.3% reduction in projected retail electricity sales in 2030. This paper discusses some of the smart grid technologies pertaining to the operation of electric power distribution networks.

Whey protein consumption after resistance exercise reduces energy intake at a post-exercise meal.

Science.gov (United States)

Monteyne, Alistair; Martin, Alex; Jackson, Liam; Corrigan, Nick; Stringer, Ellen; Newey, Jack; Rumbold, Penny L S; Stevenson, Emma J; James, Lewis J

2018-03-01

Protein consumption after resistance exercise potentiates muscle protein synthesis, but its effects on subsequent appetite in this context are unknown. This study examined appetite and energy intake following consumption of protein- and carbohydrate-containing drinks after resistance exercise. After familiarisation, 15 resistance training males (age 21 ± 1 years, body mass 78.0 ± 11.9 kg, stature 1.78 ± 0.07 m) completed two randomised, double-blind trials, consisting of lower-body resistance exercise, followed by consumption of a whey protein (PRO 23.9 ± 3.6 g protein) or dextrose (CHO 26.5 ± 3.8 g carbohydrate) drink in the 5 min post-exercise. An ad libitum meal was served 60 min later, with subjective appetite measured throughout. Drinks were flavoured and matched for energy content and volume. The PRO drink provided 0.3 g/kg body mass protein. Ad libitum energy intake (PRO 3742 ± 994 kJ; CHO 4172 ± 1132 kJ; P = 0.007) and mean eating rate (PRO 339 ± 102 kJ/min; CHO 405 ± 154 kJ/min; P = 0.009) were lower during PRO. The change in eating rate was associated with the change in energy intake (R = 0.661, P = 0.007). No interaction effects were observed for subjective measures of appetite. The PRO drink was perceived as creamier and thicker, and less pleasant, sweet and refreshing (P consumption after resistance exercise reduces subsequent energy intake, and this might be partially mediated by a reduced eating rate. Whilst this reduced energy intake is unlikely to impair hypertrophy, it may be of value in supporting an energy deficit for weight loss.

Reducing Idle Power Consumption in Office Spaces Saves U.S. Navy in Energy Costs (Fact Sheet)

Energy Technology Data Exchange (ETDEWEB)

None, None

2014-04-01

As part of a two-year project to demonstrate energy efficiency measures, renewable energy generation, and energy systems integration, the National Renewable Energy Laboratory (NREL) has identified advanced plug load controls as a promising technology for reducing energy use and related costs in the U.S. Navy's Naval Facilities Engineering Command (NAVFAC) office spaces.

Assessing the potential of hybrid energy technology to reduce exhaust emissions from global shipping

International Nuclear Information System (INIS)

Dedes, Eleftherios K.; Hudson, Dominic A.; Turnock, Stephen R.

2012-01-01

The combination of a prime mover and an energy storage device for reduction of fuel consumption has successfully been used in automotive industry. The shipping industry has utilised this for conventional submarines. The potential of a load levelling strategy through use of a hybrid battery–diesel–electric propulsion system is investigated. The goal is to reduce exhaust gas emissions by reducing fuel oil consumption through consideration of a re-engineered ship propulsion system. This work is based on operational data for a shipping fleet containing all types of bulk carriers. The engine loading and the energy requirements are calculated, and sizing of suitable propulsion and the battery storage system are proposed. The changes in overall emissions are estimated and the potential for fuel savings identified. The efficiency of the system depends on the storage medium type, the availability of energy and the displacement characteristics of the examined vessels. These results for the global fleet indicate that savings depending on storage system, vessel condition and vessel type could be up to 0.32 million tonnes in NO x , 0.07 million tonnes in SO x and 4.1 million tonnes in CO 2 . These represent a maximum 14% of reduction in dry bulk sector and 1.8% of world's fleet emissions. - Highlights: ► Global shipping makes a significant contribution to CO 2 , SO x and NO x emissions. ► We examine noon reports from a fleet of bulk carriers to identify the amount engine is operating off design. ► A hybrid propulsion system is proposed that uses multiple diesel–electric generators and battery storage. ► Analysis indicates hybrid may give an attractive rate of return as well as emissions savings in emissions. ► Implementation will require review of class society regulations.

Implementation strategy to reduce environmental impact of energy related activities in Zimbabwe

International Nuclear Information System (INIS)

1997-01-01

In 1992 UNEP-Collaborating Centre on Energy and Environment (UNEP-CCEE), Denmark and Southern Centre for Energy and Environment (SCEE), Zimbabwe, prepared a country report for Zimbabwe on Greenhouse Gas (GHG) Abatement Costing. Abatement technologies for both supply and demand side were identified in order to reduce GHG emission. The present study addresses environmental impacts of the entire energy cycle focusing on coal use in industry and power generation. Zimbabwe has proven coal reserves of more than 700 million tonnes, and the potential of geological coal resources is estimated beyond 30 billion tonnes. The conventional applications of coal include electricity generation, steam traction in railway transport, industrial boilers, tobacco curing and coking. As coal is the major source of energy for Zimbabwe, the present study aims at identification of environmental impacts of the entire coal cycle from mining to end-users of electrical energy. (EG)

An e-health intervention designed to increase workday energy expenditure by reducing prolonged occupational sitting habits.

Science.gov (United States)

Pedersen, Scott J; Cooley, Paul D; Mainsbridge, Casey

2014-01-01

Desk-based employees face multiple workplace health hazards such as insufficient physical activity and prolonged sitting. The objective of this study was to increase workday energy expenditure by interrupting prolonged occupational sitting time and introducing short-bursts of physical activity to employees' daily work habits. Over a 13-week period participants (n=17) in the intervention group were regularly exposed to a passive prompt delivered through their desktop computer that required them to stand up and engage in a short-burst of physical activity, while the control group (n=17) was not exposed to this intervention. Instead, the control group continued with their normal work routine. All participants completed a pre- and post- intervention survey to estimate workplace daily energy expenditure (calories). There was a significant 2 (Group) × 2 (Test) interaction, F (1, 32)=9.26, p employee work-related energy expenditure. Engaging employees in regular short-bursts of physical activity during the workday resulted in reduced sitting time, which may have long-term effects on the improvement of employee health.

The electric vehicles as a mean to reduce CO2 emissions and energy costs in isolated regions. The São Miguel (Azores) case study

International Nuclear Information System (INIS)

Camus, Cristina; Farias, Tiago

2012-01-01

Most of small islands around the world today, are dependent on imported fossil fuels for the majority of their energy needs especially for transport activities and electricity production. The use of locally renewable energy resources and the implementation of energy efficiency measures could make a significant contribution to their economic development by reducing fossil fuel imports. An electrification of vehicles has been suggested as a way to both reduce pollutant emissions and increase security of supply of the transportation sector by reducing the dependence on oil products imports and facilitate the accommodation of renewable electricity generation, such as wind and, in the case of volcanic islands like São Miguel (Azores) of the geothermal energy whose penetration has been limited by the valley electricity consumption level. In this research, three scenarios of EV penetration were studied and it was verified that, for a 15% LD fleet replacement by EVs with 90% of all energy needs occurring during the night, the accommodation of 10 MW of new geothermal capacity becomes viable. Under this scenario, reductions of 8% in electricity costs, 14% in energy, 23% in fossil fuels use and CO 2 emissions for the transportation and electricity production sectors could be expected. - Highlights: ► EVs impacts on the electric system in energy and power profiles, costs and emissions. ► At least an EV penetration of 15% is needed to allow new geothermal power production. ► Reductions in energy, fossil fuels use and CO 2 emissions of 9%, 16% and 17% respectively. ► Electricity production with more % of renewable technologies reduces unit costs.

Templated assembly of photoswitches significantly increases the energy-storage capacity of solar thermal fuels.

Science.gov (United States)

Kucharski, Timothy J; Ferralis, Nicola; Kolpak, Alexie M; Zheng, Jennie O; Nocera, Daniel G; Grossman, Jeffrey C

2014-05-01

Large-scale utilization of solar-energy resources will require considerable advances in energy-storage technologies to meet ever-increasing global energy demands. Other than liquid fuels, existing energy-storage materials do not provide the requisite combination of high energy density, high stability, easy handling, transportability and low cost. New hybrid solar thermal fuels, composed of photoswitchable molecules on rigid, low-mass nanostructures, transcend the physical limitations of molecular solar thermal fuels by introducing local sterically constrained environments in which interactions between chromophores can be tuned. We demonstrate this principle of a hybrid solar thermal fuel using azobenzene-functionalized carbon nanotubes. We show that, on composite bundling, the amount of energy stored per azobenzene more than doubles from 58 to 120 kJ mol(-1), and the material also maintains robust cyclability and stability. Our results demonstrate that solar thermal fuels composed of molecule-nanostructure hybrids can exhibit significantly enhanced energy-storage capabilities through the generation of template-enforced steric strain.

Waste-to-energy incineration plants as greenhouse gas reducers: a case study of seven Japanese metropolises.

Science.gov (United States)

Tabata, Tomohiro

2013-11-01

Municipal solid waste (MSW) incineration is a greenhouse gas (GHG) emitter; however, if GHG reductions, achieved by accounting for waste-to-energy, exceed GHG emissions, incineration can be considered as a net GHG reducer. In Japan, only 24.5% of MSW incineration plants perform energy recovery despite 80% of MSW being incinerated; therefore, there is great potential to extract more energy from MSW. In this study, the factors that should be considered to achieve net GHG reductions from incineration were analysed from a life cycle perspective. These considerations were then applied to the energy supply requirements in seven Japanese metropolises. Firstly, the carbon footprints of approximately 1500 incineration plants in Japan were calculated. Then, the incineration plants with negative carbon footprint values were classified as net GHG reducers. Next, the processes that contribute to the carbon footprint were evaluated, and two processes-plastic burning and electricity savings-were found to have the greatest influence. Based on the results, the energy supply requirements were analysed and discussed for seven metropolises (Sapporo, Tokyo, Nagoya, Osaka, Kobe, Takamatsu and Fukuoka) taking into account the energy demands of households. In Kobe, 16.2% of the electricity demand and 25.0% of the hot water demand could be satisfied by incineration to realise a net GHG reducer, although urban design for energy utilisation would be required.

Mixed-waste pyrolysis of biomass and plastics waste – A modelling approach to reduce energy usage

International Nuclear Information System (INIS)

Oyedun, Adetoyese Olajire; Gebreegziabher, Tesfaldet; Ng, Denny K.S.; Hui, Chi Wai

2014-01-01

Thermal co-processing of waste mixtures had gained a lot of attention in the last decade. This is largely due to certain synergistic effects such as higher quantity and better quality of oil, limited supply of certain feedstock and improving the overall pyrolysis process. Many experiments have been conducted via TGA analysis and different reactors to achieve the stated synergistic effects in co-pyrolysis of biomass and plastic wastes. The thermal behaviour of plastics during pyrolysis is different from that of biomass because its decomposition happens at a high temperature range with sudden release of volatile compared to biomass which have a wide range of thermal decomposition. A properly designed recipe and operational strategy of mixing feedstock can ease the operational difficulties and at the same time decrease energy consumption and/or improve the product yield. Therefore it is worthwhile to study the possible synergistic effects on the overall energy used during co-pyrolysis process. In this work, two different modelling approaches were used to study the energy related synergistic effect between polystyrene (PS) and bamboo waste. The mass loss and volatile generation profiles show that significant interactions between the two feedstocks exist. The results also show that both modelling approaches give an appreciable synergy effect of reduction in overall energy when PS and bamboo are co-pyrolysed together. However, the second approach which allows interaction between the two feedstocks gives a more reduction in overall energy usage up to 6.2% depending on the ratio of PS in the mixed blend. - Highlights: • Proposed the mixed-waste pyrolysis modelling via two modelling approaches. • Study the energy related synergistic effects when plastics and biomass are pyrolysed together. • Mass loss and volatile generation profiles show the existence of significant interactions. • Energy usage can be reduced by up to 6.2% depending on the percentage of the plastic

Advanced air distribution: Improving health and comfort while reducing energy use

DEFF Research Database (Denmark)

Melikov, Arsen Krikor

2015-01-01

-quality indoor environments at the same time as low-energy consumption. Advanced air distribution, designed to supply clean air where, when, and as much as needed, makes it possible to efficiently achieve thermal comfort, control exposure to contaminants, provide high-quality air for breathing and minimizing......Indoor environment affects the health, comfort, and performance of building occupants. The energy used for heating, cooling, ventilating, and air conditioning of buildings is substantial. Ventilation based on total volume air distribution in spaces is not always an efficient way to provide high...... the risk of airborne cross-infection while reducing energy use. This study justifies the need for improving the present air distribution design in occupied spaces, and in general the need for a paradigm shift from the design of collective environments to the design of individually controlled environments...

Non-Q-wave myocardial infarction: impaired myocardial energy metabolism in regions with reduced 99mTc-MIBI accumulation.

Science.gov (United States)

Moka, D; Baer, F M; Theissen, P; Schneider, C A; Dietlein, M; Erdmann, E; Schicha, H

2001-05-01

Reduced regional technetium-99m methoxyisobutylisonitrile (99mTc-MIBI) accumulation in patients with chronic non-Q-wave infarction (NQWI) but without significant coronary artery stenosis indicates non-transmural damage of the myocardial wall. The aim of this study was to characterise cardiac energy metabolism after NQWI using phosphorus-31 magnetic resonance spectroscopy (31P-MRS) and to compare the biochemical remodelling with changes in regional 99mTc-MIBI uptake and with morphological and functional parameters assessed by magnetic resonance imaging (MRI). Fifteen patients with a history of NQWI, exclusion of significant coronary artery stenosis (energy metabolism. Spectroscopic measurements were performed in the infarct-related myocardial region. Corresponding gradient-echo MR images and myocardial 99mTc-MIBI single-photon emission tomography images were acquired for exact localisation of the infarct region. All examinations were performed at rest under anti-ischaemic medication. Data were compared with those of patients in whom coronary artery disease had been excluded by angiography (group B, n=10). All patients of group A displayed anterior wall hypokinesia in the infarcted area on both ventriculography and MRI, with a reduced myocardial accumulation of 99mTc-MIBI (66.3%+/-11.8% vs 95.6%+/-2.2% in group B). The mean wall thickness during the complete cardiac cycle (9.5+/-1.8 mm vs 13.1+/-1.1 mm in group B, Penergy metabolism.

Large-scale Manufacturing of Nanoparticulate-based Lubrication Additives for Improved Energy Efficiency and Reduced Emissions

Energy Technology Data Exchange (ETDEWEB)

Erdemir, Ali [Argonne National Laboratory

2013-09-26

This project was funded under the Department of Energy (DOE) Lab Call on Nanomanufacturing for Energy Efficiency and was directed toward the development of novel boron-based nanocolloidal lubrication additives for improving the friction and wear performance of machine components in a wide range of industrial and transportation applications. Argonne's research team concentrated on the scientific and technical aspects of the project, using a range of state-of-the art analytical and tribological test facilities. Argonne has extensive past experience and expertise in working with boron-based solid and liquid lubrication additives, and has intellectual property ownership of several. There were two industrial collaborators in this project: Ashland Oil (represented by its Valvoline subsidiary) and Primet Precision Materials, Inc. (a leading nanomaterials company). There was also a sub-contract with the University of Arkansas. The major objectives of the project were to develop novel boron-based nanocolloidal lubrication additives and to optimize and verify their performance under boundary-lubricated sliding conditions. The project also tackled problems related to colloidal dispersion, larger-scale manufacturing and blending of nano-additives with base carrier oils. Other important issues dealt with in the project were determination of the optimum size and concentration of the particles and compatibility with various base fluids and/or additives. Boron-based particulate additives considered in this project included boric acid (H{sub 3}BO{sub 3}), hexagonal boron nitride (h-BN), boron oxide, and borax. As part of this project, we also explored a hybrid MoS{sub 2} + boric acid formulation approach for more effective lubrication and reported the results. The major motivation behind this work was to reduce energy losses related to friction and wear in a wide spectrum of mechanical systems and thereby reduce our dependence on imported oil. Growing concern over greenhouse

In situ evaluation of water and energy consumptions at the end use level: The influence of flow reducers and temperature in baths.

Science.gov (United States)

Matos, C; Briga-Sá, A; Bentes, I; Faria, D; Pereira, S

2017-05-15

Nowadays, water and energy consumption is intensifying every year in most of the countries. This perpetual increase will not be supportable in the long run, making urgently to manage these resources on a sustainable way. Domestic consumptions of water and electric energy usually are related and it's important to study that relation, identifying opportunities for use efficient improvement. In fact, without an understanding of water-energy relations, there are water efficiency measures that may lead to unintentional costs in the energy efficiency field. In order to take full advantage of combined effect between water and energy water management methodologies, it is necessary to collect data to ensure that the efforts are directed through the most effective paths. This paper presents a study based in the characterization, measurement and analysis of water and electricity consumption in a single family house (2months period) in order to find an interdependent relationship between consumptions at the end user level. The study was carried out on about 200 baths, divided in four different scenarios where the influence of two variables was tested: the flow reducer valve and the bath temperature. Data showed that the presence of flow reducer valve decreased electric energy consumption and water consumption, but increased the bath duration. Setting a lower temperature in water-heater, decreased electric consumption, water consumption and bath duration. Analysing the influence of the flow reducer valve and 60°C temperature simultaneously, it was concluded that it had a significant influence on electric energy consumption and on the baths duration but had no influence on water consumption. Copyright © 2017 The Author(s). Published by Elsevier B.V. All rights reserved.

Asheville, North Carolina: Reducing Electricity Demand through Building Programs & Policies (City Energy: From Data to Decisions)

Energy Technology Data Exchange (ETDEWEB)

Office of Strategic Programs, Strategic Priorities and Impact Analysis Team

2017-09-29

This fact sheet "Asheville, North Carolina: Reducing Electricity Demand through Building Programs & Policies" explains how the City of Asheville used data from the U.S. Department of Energy's Cities Leading through Energy Analysis and Planning (Cities-LEAP) and the State and Local Energy Data (SLED) programs to inform its city energy planning. It is one of ten fact sheets in the "City Energy: From Data to Decisions" series.

Estimating the energy-saving benefit of reduced-flow and/or multi-speed commercial kitchen ventilation systems

Energy Technology Data Exchange (ETDEWEB)

Fisher, D.; Schmid, F.; Spata, A.J.

1999-07-01

Kitchen exhaust ventilation systems are recognized as a major energy user within commercial food service facilities and restaurants. Minimizing the design ventilation rate of an appliance/hood system by optimizing hood performance in the laboratory is a viable strategy for reducing the makeup air heating and cooling loads as well as the exhaust and supply fan energy. Cutting back the exhaust flow under conditions of noncooking (appliance idle) can further reduce the energy load associated with a kitchen ventilation system. An optimized, two-speed exhaust system was installed within the scope of an energy-efficient, quick service restaurant (QSR) design and demonstration project. This paper evaluates the energy benefit of this variable-flow strategy as well as the savings associated with reducing the design ventilation rate (compared to an off-the-shelf exhaust hood). The paper describes a new public-domain software tool for estimating heating and cooling loads associated with the makeup air requirements of commercial kitchens. This bin-based software provides ASHRAE engineers with an alternative to hand calculations or more sophisticated hour-by-hour simulation. The dramatic impact that both makeup air set point and geographic location have on the outdoor air load is illustrated. The paper concludes with an industry-wide projection of energy savings associated with optimizing the design and operation of commercial kitchen ventilation (CKV) systems.

Consumption of fuels and energy in the coking industry and ways of reducing consumption

Energy Technology Data Exchange (ETDEWEB)

Vasil' ev, Yu.S.; Tsel' ik, M.P.; Belkina, T.V. (Khar' kovskii Nauchno-Issledovatel' skii Uglekhimicheski Institut (USSR))

1989-08-01

Coking plants in the USSR consume 4,000 million kWh electric energy, 100 million GJ heat energy and 35,000 million m{sup 3} gaseous fuels per year. Structure of energy consumption is the following: 68% gaseous fuels, 24% steam and 8% electric energy. Processes of coal preparation, crushing, mixing, coking and quenching are analyzed from the point of view of energy consumption. The following methods for reducing energy consumption are discussed: using the FM-25 flotation machines for flotation of coking coal slurries, briquetting the whole coal charge for coking, optimization of air supply rates for combustion of gases used for coke oven heating, use of control systems for coke oven heating considering coal charge density, waste heat utilization from quenching. 4 refs.

Nano-CL-20/HMX Cocrystal Explosive for Significantly Reduced Mechanical Sensitivity

Directory of Open Access Journals (Sweden)

Chongwei An

2017-01-01

Full Text Available Spray drying method was used to prepare cocrystals of hexanitrohexaazaisowurtzitane (CL-20 and cyclotetramethylene tetranitramine (HMX. Raw materials and cocrystals were characterized using scanning electron microscopy, X-ray diffraction, differential scanning calorimetry, Raman spectroscopy, and Fourier transform infrared spectroscopy. Impact and friction sensitivity of cocrystals were tested and analyzed. Results show that, after preparation by spray drying method, microparticles were spherical in shape and 0.5–5 µm in size. Particles formed aggregates of numerous tiny plate-like cocrystals, whereas CL-20/HMX cocrystals had thicknesses of below 100 nm. Cocrystals were formed by C–H⋯O bonding between –NO2 (CL-20 and –CH2– (HMX. Nanococrystal explosives exhibited drop height of 47.3 cm, and friction demonstrated explosion probability of 64%. Compared with raw HMX, cocrystals displayed significantly reduced mechanical sensitivity.

Evaluation of Strategies to Reducing Traction Energy Consumption of Metro Systems Using an Optimal Train Control Simulation Model

Directory of Open Access Journals (Sweden)

Shuai Su

2016-02-01

Full Text Available Increasing attention is being paid to the energy efficiency in metro systems to reduce the operational cost and to advocate the sustainability of railway systems. Classical research has studied the energy-efficient operational strategy and the energy-efficient system design separately to reduce the traction energy consumption. This paper aims to combine the operational strategies and the system design by analyzing how the infrastructure and vehicle parameters of metro systems influence the operational traction energy consumption. Firstly, a solution approach to the optimal train control model is introduced, which is used to design the Optimal Train Control Simulator(OTCS. Then, based on the OTCS, the performance of some important energy-efficient system design strategies is investigated to reduce the trains’ traction energy consumption, including reduction of the train mass, improvement of the kinematic resistance, the design of the energy-saving gradient, increasing the maximum traction and braking forces, introducing regenerative braking and timetable optimization. As for these energy-efficient strategies, the performances are finally evaluated using the OTCS with the practical operational data of the Beijing Yizhuang metro line. The proposed approach gives an example to quantitatively analyze the energy reduction of different strategies in the system design procedure, which may help the decision makers to have an overview of the energy-efficient performances and then to make decisions by balancing the costs and the benefits.

Cost Benefit Analysis of Using Clean Energy Supplies to Reduce Greenhouse Gas Emissions of Global Automotive Manufacturing

Directory of Open Access Journals (Sweden)

Xiang Zhao

2011-09-01

Full Text Available Automotive manufacturing is energy-intensive. The consumed energy contributes to the generation of significant amounts of greenhouse gas (GHG emissions by the automotive manufacturing industry. In this paper, a study is conducted on assessing the application potential of such clean energy power systems as solar PV, wind and fuel cells in reducing the GHG emissions of the global auto manufacturing industry. The study is conducted on the representative solar PV, wind and fuel cell clean energy systems available on the commercial market in six representative locations of GM’s global facilities, including the United States, Mexico, Brazil, China, Egypt and Germany. The results demonstrate that wind power is superior to other two clean energy technologies in the economic performance of the GHG mitigation effect. Among these six selected countries, the highest GHG emission mitigation potential is in China, through wind power supply. The maximum GHG reduction could be up to 60 tons per $1,000 economic investment on wind energy supply in China. The application of wind power systems in the United States and Germany could also obtain relatively high GHG reductions of between 40–50 tons per $1,000 economic input. When compared with wind energy, the use of solar and fuel cell power systems have much less potential for GHG mitigation in the six countries selected. The range of median GHG mitigation values resulting from solar and wind power supply are almost at the same level.

NASA Fixed Wing Project Propulsion Research and Technology Development Activities to Reduce Thrust Specific Energy Consumption

Science.gov (United States)

Hathaway, Michael D.; DelRasario, Ruben; Madavan, Nateri K.

2013-01-01

This paper presents an overview of the propulsion research and technology portfolio of NASA Fundamental Aeronautics Program Fixed Wing Project. The research is aimed at significantly reducing the thrust specific fuel/energy consumption of notional advanced fixed wing aircraft (by 60 % relative to a baseline Boeing 737-800 aircraft with CFM56-7B engines) in the 2030-2035 time frame. The research investments described herein are aimed at improving propulsive efficiency through higher bypass ratio fans, improving thermal efficiency through compact high overall pressure ratio gas generators, and exploring the potential benefits of boundary layer ingestion propulsion and hybrid gas-electric propulsion concepts.

Energy harvesting solar, wind, and ocean energy conversion systems

CERN Document Server

Khaligh, Alireza

2009-01-01

Also called energy scavenging, energy harvesting captures, stores, and uses ""clean"" energy sources by employing interfaces, storage devices, and other units. Unlike conventional electric power generation systems, renewable energy harvesting does not use fossil fuels and the generation units can be decentralized, thereby significantly reducing transmission and distribution losses. But advanced technical methods must be developed to increase the efficiency of devices in harvesting energy from environmentally friendly, ""green"" resources and converting them into electrical energy.Recognizing t

Control Strategies to Reduce the Energy Consumption of Central Domestic Hot Water Systems

Energy Technology Data Exchange (ETDEWEB)

Dentz, Jordan [The Levy Partnership, Inc., New York, NY (United States). Advanced Residential Integrated Energy Solutions; Ansanelli, Eric [The Levy Partnership, Inc., New York, NY (United States). Advanced Residential Integrated Energy Solutions; Henderson, Hugh [The Levy Partnership, Inc., New York, NY (United States). Advanced Residential Integrated Energy Solutions; Varshney, Kapil [The Levy Partnership, Inc., New York, NY (United States). Advanced Residential Integrated Energy Solutions

2016-06-23

Domestic hot water (DHW) heating is the second largest energy end use in U.S. buildings, exceeded only by space conditioning. Recirculation systems consisting of a pump and piping loop(s) are commonly used in multifamily buildings to reduce wait time for hot water at faucets; however, constant pumping increases energy consumption by exposing supply and return line piping to continuous heat loss, even during periods when there is no demand for hot water. In this study, ARIES installed and tested two types of recirculation controls in a pair of buildings in order to evaluate their energy savings potential. Demand control, temperature modulation controls, and the simultaneous operation of both were compared to the baseline case of constant recirculation. Additionally, interactive effects between DHW control fuel reductions and space conditioning (heating and cooling) were estimated in order to make more realistic predictions of the payback and financial viability of retrofitting DHW systems with these controls. Results showed that DHW fuel consumption reduced by 7% after implementing the demand control technique, 2% after implementing temperature modulation, and 15% after implementing demand control and temperature modulation techniques simultaneously; recirculation pump runtime was reduced to 14 minutes or less per day. With space heating and cooling interactions included, the estimated annual cost savings were 8%, 1%, and 14% for the respective control techniques. Possible complications in the installation, commissioning and operation of the controls were identified and solutions offered.

Control Strategies to Reduce the Energy Consumption of Central Domestic Hot Water Systems

Energy Technology Data Exchange (ETDEWEB)

Dentz, Jordan; Ansanelli, Eric; Henderson, Hugh; Varshney, Kapil

2016-06-03

Domestic hot water (DHW) heating is the second largest energy end use in U.S. buildings, exceeded only by space conditioning. Recirculation systems consisting of a pump and piping loop(s) are commonly used in multifamily buildings to reduce wait time for hot water at faucets; however, constant pumping increases energy consumption by exposing supply and return line piping to continuous heat loss, even during periods when there is no demand for hot water. In this study, ARIES installed and tested two types of recirculation controls in a pair of buildings in order to evaluate their energy savings potential. Demand control, temperature modulation controls, and the simultaneous operation of both were compared to the baseline case of constant recirculation. Additionally, interactive effects between DHW control fuel reductions and space conditioning (heating and cooling) were estimated in order to make more realistic predictions of the payback and financial viability of retrofitting DHW systems with these controls. Results showed that DHW fuel consumption reduced by 7% after implementing the demand control technique, 2% after implementing temperature modulation, and 15% after implementing demand control and temperature modulation techniques simultaneously; recirculation pump runtime was reduced to 14 minutes or less per day. With space heating and cooling interactions included, the estimated annual cost savings were 8%, 1%, and 14% for the respective control techniques. Possible complications in the installation, commissioning and operation of the controls were identified and solutions offered.

Facile synthesis of reduced graphene oxide/peroxomolybdate(VI)-citrate composite and its potential energy storage application

Energy Technology Data Exchange (ETDEWEB)

Ciszewski, Mateusz; Benke, Grzegorz; Leszczynska-Sejda, Katarzyna; Kopyto, Dorota [Institute of Non Ferrous Metals, Department of Hydrometallurgy, Gliwice (Poland)

2017-11-15

A new energy storage material based on molybdate active species has been presented. Molybdenum seems to be a perspective material in supercapacitors because of numerous possible metal oxidation states, electrolyte storage by means of various chemical reactions and availability in comparison to other refractory metals. Material synthesized within this research was composed of reduced graphene oxide matrix and peroxomolybdate(VI)-citrate active dimers. It was showed that peroxomolybdate(VI)-citrate structure enhanced electrochemical activity of symmetric supercapacitor. Simple methodology was used to synthesize a composite with pH adjustment as the key step. The specific capacity calculated from galvanostatic charge/discharge curves was as high as 250 F/g. Material was distinguished by good cyclability with 5% capacity loss after 1000 cycles. The increase in charge transfer resistance, induced by metal-oxygen compound within the carbon matrix was relatively low, compared to parent reduced graphene oxide. Amorphous structure of peroxomolybdate(VI)-modified material was observed with slight increase in the interlayer distance in comparison to parent reduced graphene oxide. The height and lateral size of crystallites were also determined. Significant decrease in the specific surface area of peroxomolybdate(VI)-modified composite was observed, in comparison to the parent reduced graphene oxide. (orig.)

Facile synthesis of reduced graphene oxide/peroxomolybdate(VI)-citrate composite and its potential energy storage application

International Nuclear Information System (INIS)

Ciszewski, Mateusz; Benke, Grzegorz; Leszczynska-Sejda, Katarzyna; Kopyto, Dorota

2017-01-01

A new energy storage material based on molybdate active species has been presented. Molybdenum seems to be a perspective material in supercapacitors because of numerous possible metal oxidation states, electrolyte storage by means of various chemical reactions and availability in comparison to other refractory metals. Material synthesized within this research was composed of reduced graphene oxide matrix and peroxomolybdate(VI)-citrate active dimers. It was showed that peroxomolybdate(VI)-citrate structure enhanced electrochemical activity of symmetric supercapacitor. Simple methodology was used to synthesize a composite with pH adjustment as the key step. The specific capacity calculated from galvanostatic charge/discharge curves was as high as 250 F/g. Material was distinguished by good cyclability with 5% capacity loss after 1000 cycles. The increase in charge transfer resistance, induced by metal-oxygen compound within the carbon matrix was relatively low, compared to parent reduced graphene oxide. Amorphous structure of peroxomolybdate(VI)-modified material was observed with slight increase in the interlayer distance in comparison to parent reduced graphene oxide. The height and lateral size of crystallites were also determined. Significant decrease in the specific surface area of peroxomolybdate(VI)-modified composite was observed, in comparison to the parent reduced graphene oxide. (orig.)

Scoring predictive models using a reduced representation of proteins: model and energy definition.

Science.gov (United States)

Fogolari, Federico; Pieri, Lidia; Dovier, Agostino; Bortolussi, Luca; Giugliarelli, Gilberto; Corazza, Alessandra; Esposito, Gennaro; Viglino, Paolo

2007-03-23

Reduced representations of proteins have been playing a keyrole in the study of protein folding. Many such models are available, with different representation detail. Although the usefulness of many such models for structural bioinformatics applications has been demonstrated in recent years, there are few intermediate resolution models endowed with an energy model capable, for instance, of detecting native or native-like structures among decoy sets. The aim of the present work is to provide a discrete empirical potential for a reduced protein model termed here PC2CA, because it employs a PseudoCovalent structure with only 2 Centers of interactions per Amino acid, suitable for protein model quality assessment. All protein structures in the set top500H have been converted in reduced form. The distribution of pseudobonds, pseudoangle, pseudodihedrals and distances between centers of interactions have been converted into potentials of mean force. A suitable reference distribution has been defined for non-bonded interactions which takes into account excluded volume effects and protein finite size. The correlation between adjacent main chain pseudodihedrals has been converted in an additional energetic term which is able to account for cooperative effects in secondary structure elements. Local energy surface exploration is performed in order to increase the robustness of the energy function. The model and the energy definition proposed have been tested on all the multiple decoys' sets in the Decoys'R'us database. The energetic model is able to recognize, for almost all sets, native-like structures (RMSD less than 2.0 A). These results and those obtained in the blind CASP7 quality assessment experiment suggest that the model compares well with scoring potentials with finer granularity and could be useful for fast exploration of conformational space. Parameters are available at the url: http://www.dstb.uniud.it/~ffogolari/download/.

Monosodium L-glutamate in soup reduces subsequent energy intake from high-fat savoury food in overweight and obese women.

Science.gov (United States)

Miyaki, Takashi; Imada, Toshifumi; Hao, Susan Shuzhen; Kimura, Eiichiro

2016-01-14

The umami seasoning, monosodium L-glutamate (MSG), has been shown to increase satiety in normal body weight adults, although the results have not been consistent. The satiety effect of MSG in overweight and obese adults has not been examined yet. The objective of the present study was to investigate the effect of MSG in a vegetable soup on subsequent energy intakes as well as food selection in overweight and obese adult women without eating disorders. A total of sixty-eight overweight and obese women (BMI range: 25·0-39·9 kg/m²), otherwise healthy, were recruited to our study. A fixed portion (200 ml) of control vegetable soup or the same soup with added MSG (0·5 g/100 ml) was provided 10 min before an ad libitum lunch and an ad libitum snack in the mid-afternoon. The control soup had equivalent amount of Na to the soup with added MSG. Energy intakes at the ad libitum lunch and ad libitum snack time after the soup preload were assessed using a randomised, double-blind, two-way cross-over design. The soup with MSG in comparison with the control soup resulted in significantly lower consumption of energy at lunch. The addition of MSG in the soup also reduced energy intake from high-fat savoury foods. The soup with MSG showed lower but no significant difference in energy intake at mid-afternoon. The addition of umami seasoning MSG in a vegetable soup may decrease subsequent energy intake in overweight and obese women who do not have eating disorders.

We forgot half of the population! The significance of gender in Danish energy renovation projects

DEFF Research Database (Denmark)

Tjørring, Lise

2016-01-01

that the way people live their everyday lives plays a crucial role in understanding why they choose whether to perform an energy renovation. This study is based on an anthropological investigation of ten Danish families and their decision-making process while receiving free energy advice, which, in many cases......, ended as an energy renovation project in the home. During the study, gender emerged as a significant factor in two ways. First, energy renovations were perceived differently by men and women as a consequence of their different everyday practices. Second, there was a cultural norm about the division...... that contains different gender practices and cultural influences....

The impact of state energy programs and other contextual factors on U.S. buildings energy consumption

Science.gov (United States)

Ofori-Boadu, Andrea N. Y. A.

High energy consumption in the United States has been influenced by populations, climates, income and other contextual factors. In the past decades, U.S. energy policies have pursued energy efficiency as a national strategy for reducing U.S. environmental degradation and dependence on foreign oils. The quest for improved energy efficiency has led to the development of energy efficient technologies and programs. The implementation of energy programs in the complex U.S. socio-technical environment is believed to promote the diffusion of energy efficiency technologies. However, opponents doubt the fact that these programs have the capacity to significantly reduce U.S. energy consumption. In order to contribute to the ongoing discussion, this quantitative study investigated the relationships existing among electricity consumption/ intensity, energy programs and contextual factors in the U.S. buildings sector. Specifically, this study sought to identify the significant predictors of electricity consumption and intensity, as well as estimate the overall impact of selected energy programs on electricity consumption and intensity. Using state-level secondary data for 51 U.S. states from 2006 to 2009, seven random effects panel data regression models confirmed the existence of significant relationships among some energy programs, contextual factors, and electricity consumption/intensity. The most significant predictors of improved electricity efficiency included the price of electricity, public benefits funds program, building energy codes program, financial and informational incentives program and the Leadership in Energy and Environmental Design (LEED) program. Consistently, the Southern region of the U.S. was associated with high electricity consumption and intensity; while the U.S. commercial sector was the greater benefactor from energy programs. On the average, energy programs were responsible for approximately 7% of the variation observed in electricity consumption

Energy supply and energy saving in Ukraine

Directory of Open Access Journals (Sweden)

V.M. Ilchenko

2015-09-01

Full Text Available The article examines the main problems and solutions of energy saving and energy supply in Ukraine. Low energy efficiency has become one of the main factors of the crisis in the Ukrainian economy. The most relevant scientific and methodical approaches to assessment of the level of energy consumption and saving are indicated. The comparative analysis of annual energy use has been made. A potential to solve energy supply problems is strongly correlated with the ability to ensure the innovative development of economy for efficient and economical use of existing and imported energy resources. The ways for reducing of energy resource consumption have been suggested. Creation of technological conditions for the use of alternative energy sources is considered to be rational also. The development of renewable sources of energy (alternative and renewable energy sources will provide a significant effect in reducing the use of traditional energy sources, harmful emissions and greenhouse gas. Under these conditions, increasing of energy efficiency of economy and its competitiveness can be real. Improvement of environmental and social conditions of citizens of the country will mark a positive step towards the EU, and also will cancel some problems of the future generation.

The significance of sensory appeal for reduced meat consumption.

Science.gov (United States)

Tucker, Corrina A

2014-10-01

Reducing meat (over-)consumption as a way to help address environmental deterioration will require a range of strategies, and any such strategies will benefit from understanding how individuals might respond to various meat consumption practices. To investigate how New Zealanders perceive such a range of practices, in this instance in vitro meat, eating nose-to-tail, entomophagy and reducing meat consumption, focus groups involving a total of 69 participants were held around the country. While it is the damaging environmental implications of intensive farming practices and the projected continuation of increasing global consumer demand for meat products that has propelled this research, when asked to consider variations on the conventional meat-centric diet common to many New Zealanders, it was the sensory appeal of the areas considered that was deemed most problematic. While an ecological rationale for considering these 'meat' alternatives was recognised and considered important by most, transforming this value into action looks far less promising given the recurrent sensory objections to consuming different protein-based foods or of reducing meat consumption. This article considers the responses of focus group participants in relation to each of the dietary practices outlined, and offers suggestions on ways to encourage a more environmentally viable diet. Copyright © 2014 Elsevier Ltd. All rights reserved.

Significant change of local atomic configurations at surface of reduced activation Eurofer steels induced by hydrogenation treatments

Energy Technology Data Exchange (ETDEWEB)

Greculeasa, S.G.; Palade, P.; Schinteie, G. [National Institute for Materials Physics, P.O. Box MG-7, 77125, Bucharest-Magurele (Romania); Kuncser, A.; Stanciu, A. [National Institute for Materials Physics, P.O. Box MG-7, 77125, Bucharest-Magurele (Romania); University of Bucharest, Faculty of Physics, 77125, Bucharest-Magurele (Romania); Lungu, G.A. [National Institute for Materials Physics, P.O. Box MG-7, 77125, Bucharest-Magurele (Romania); Porosnicu, C.; Lungu, C.P. [National Institute for Laser, Plasma and Radiation Physics, 77125, Bucharest-Magurele (Romania); Kuncser, V., E-mail: kuncser@infim.ro [National Institute for Materials Physics, P.O. Box MG-7, 77125, Bucharest-Magurele (Romania)

2017-04-30

Highlights: • Engineering of Eurofer slab properties by hydrogenation treatments. • Hydrogenation modifies significantly the local atomic configurations at the surface. • Hydrogenation increases the expulsion of the Cr atoms toward the very surface. • Approaching binomial atomic distribution by hydrogenation in the next surface 100 nm. - Abstract: Reduced-activation steels such as Eurofer alloys are candidates for supporting plasma facing components in tokamak-like nuclear fusion reactors. In order to investigate the impact of hydrogen/deuterium insertion in their crystalline lattice, annealing treatments in hydrogen atmosphere have been applied on Eurofer slabs. The resulting samples have been analyzed with respect to local structure and atomic configuration both before and after successive annealing treatments, by X-ray diffractometry (XRD), scanning electron microscopy and energy dispersive spectroscopy (SEM-EDS), X-ray photoelectron spectroscopy (XPS) and conversion electron Mössbauer spectroscopy (CEMS). The corroborated data point out for a bcc type structure of the non-hydrogenated alloy, with an average alloy composition approaching Fe{sub 0.9}Cr{sub 0.1} along a depth of about 100 nm. EDS elemental maps do not indicate surface inhomogeneities in concentration whereas the Mössbauer spectra prove significant deviations from a homogeneous alloying. The hydrogenation increases the expulsion of the Cr atoms toward the surface layer and decreases their oxidation, with considerable influence on the surface properties of the steel. The hydrogenation treatment is therefore proposed as a potential alternative for a convenient engineering of the surface of different Fe-Cr based alloys.

New Building Principles In Consequence Of Legislative Demands For Reduced Energy Consumption In Danish Housing

DEFF Research Database (Denmark)

Jessen, Rasmus Zederkof; Brohus, Henrik; Kirkegaard, Poul Henning

2006-01-01

The increasing restrictions in coming building codes regarding energy consumption in housing generate a need to rethink the building design as well as the building process. This paper discusses the need to change/challenge the way structures are conceived in order to accommodate new legislative...... demands regarding energy consumption. More often than not sustainable aspects like the need for reduced energy consumption are implemented late in the design process. This paper investigates the affect of incorporating aspects like solar heat gain and energy consumption in the initial concept...

Single-source dual-energy spectral multidetector CT of pancreatic adenocarcinoma: Optimization of energy level viewing significantly increases lesion contrast

International Nuclear Information System (INIS)

Patel, B.N.; Thomas, J.V.; Lockhart, M.E.; Berland, L.L.; Morgan, D.E.

2013-01-01

V was 31 ± 25 HU (p = 0.007). Conclusion: Significantly increased pancreatic lesion contrast was noted at lower viewing energies using spectral MDCT. Individual patient CNR-optimized energy level images have the potential to improve lesion conspicuity.

Methodology for reducing energy and resource costs in construction of trenchless crossover of pipelines

Science.gov (United States)

Toropov, V. S.

2018-05-01

The paper suggests a set of measures to select the equipment and its components in order to reduce energy costs in the process of pulling the pipeline into the well in the constructing the trenchless pipeline crossings of various materials using horizontal directional drilling technology. A methodology for reducing energy costs has been developed by regulating the operation modes of equipment during the process of pulling the working pipeline into a drilled and pre-expanded well. Since the power of the drilling rig is the most important criterion in the selection of equipment for the construction of a trenchless crossover, an algorithm is proposed for calculating the required capacity of the rig when operating in different modes in the process of pulling the pipeline into the well.

Predictive Maintenance (PdM) Centralization for Significant Energy Savings

Energy Technology Data Exchange (ETDEWEB)

Smith, Dale

2010-09-15

Cost effective predictive maintenance (PdM) technologies and basic energy calculations can mine energy savings form processes or maintenance activities. Centralizing and packaging this information correctly empowers facility maintenance and reliability professionals to build financial justification and support for strategies and personnel to weather global economic downturns and competition. Attendees will learn how to: Systematically build a 'pilot project' for applying PdM and tracking systems; Break down a typical electrical bill to calculate energy savings; Use return on investment (ROI) calculations to identify the best and highest value options, strategies and tips for substantiating your energy reduction maintenance strategies.

Bookending the Opportunity to Lower Wind’s LCOE by Reducing the Uncertainty Surrounding Annual Energy Production

Energy Technology Data Exchange (ETDEWEB)

Bolinger, Mark [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Energy Analysis and Environmental Impacts Div.

2017-06-01

Reducing the performance risk surrounding a wind project can potentially lead to a lower weighted-average cost of capital (WACC), and hence a lower levelized cost of energy (LCOE), through an advantageous shift in capital structure, and possibly also a reduction in the cost of capital. Specifically, a reduction in performance risk will move the 1-year P99 annual energy production (AEP) estimate closer to the P50 AEP estimate, which in turn reduces the minimum debt service coverage ratio (DSCR) required by lenders, thereby allowing the project to be financed with a greater proportion of low-cost debt. In addition, a reduction in performance risk might also reduce the cost of one or more of the three sources of capital that are commonly used to finance wind projects: sponsor or cash equity, tax equity, and/or debt. Preliminary internal LBNL analysis of the maximum possible LCOE reduction attainable from reducing the performance risk of a wind project found a potentially significant opportunity for LCOE reduction of ~$10/MWh, by reducing the P50 DSCR to its theoretical minimum value of 1.0 (Bolinger 2015b, 2014) and by reducing the cost of sponsor equity and debt by one-third to one-half each (Bolinger 2015a, 2015b). However, with FY17 funding from the U.S. Department of Energy’s Atmosphere to Electrons (A2e) Performance Risk, Uncertainty, and Finance (PRUF) initiative, LBNL has been revisiting this “bookending” exercise in more depth, and now believes that its earlier preliminary assessment of the LCOE reduction opportunity was overstated. This reassessment is based on two new-found understandings: (1) Due to ever-present and largely irreducible inter-annual variability (IAV) in the wind resource, the minimum required DSCR cannot possibly fall to 1.0 (on a P50 basis), and (2) A reduction in AEP uncertainty will not necessarily lead to a reduction in the cost of capital, meaning that a shift in capital structure is perhaps the best that can be expected (perhaps

Earthworms influenced by reduced tillage, conventional tillage and energy forest in Swedish agricultural field experiments

Energy Technology Data Exchange (ETDEWEB)

Lagerloef, Jan (SLU, Department of Ecology, Swedish University of Agricultural Sciences, Uppsala (Sweden)), Email: Jan.Lagerlof@ekol.slu.se; Paalsson, Olof; Arvidsson, Johan (SLU, Department of Soil and Environment, Swedish University of Agricultural Sciences, Uppsala (Sweden))

2012-03-15

We compared earthworm density, depth distribution and species composition in three soil cultivation experiments including the treatments ploughless tillage and mouldboard ploughing. Sampling was done in September 2005 and for one experiment also in 1994. By yearly sampling 1995-2005, earthworms in an energy forest of Salix viminalis were compared with those in an adjacent arable field. Sampling method was digging of soil blocks and hand sorting and formalin sampling in one cultivation experiment. Both methods were used in the energy forest and arable land comparison. In two soil cultivation experiments, highest abundances or biomass were found in ploughless tillage. Earthworm density was higher in the upper 10 cm, especially in the ploughless tillage. Earthworm density was significantly higher in the energy forest than in the arable field. Formalin sampling revealed c. 36% of the earthworm numbers found by digging in the energy forest and gave almost no earthworms in the arable field. In all treatments with soil cultivation, species living and feeding in the rhizosphere and soil dominated. One such species, Allolobophora chlorotica, was more abundant under mouldboard ploughing than ploughless tillage. Lumbricus terrestris, browsing on the surface and producing deep vertical burrows, was more common in the ploughless tillage. Species living and feeding close to the soil surface were almost only found in the energy forest, which had not been soil cultivated since 1984. The findings support earlier studies pointing out possibilities to encourage earthworms by reduced soil cultivation. This is one of the first published studies that followed earthworm populations in an energy forest plantation during several years. Explanation of earthworm reactions to management and environmental impacts should be done with consideration of the ecology of species or species groups. Earthworm sampling by formalin must always be interpreted with caution and calibrated by digging and

Metagenomics shows that low-energy anaerobic-aerobic treatment reactors reduce antibiotic resistance gene levels from domestic wastewater.

Science.gov (United States)

Christgen, Beate; Yang, Ying; Ahammad, S Z; Li, Bing; Rodriquez, D Catalina; Zhang, Tong; Graham, David W

2015-02-17

Effective domestic wastewater treatment is among our primary defenses against the dissemination of infectious waterborne disease. However, reducing the amount of energy used in treatment processes has become essential for the future. One low-energy treatment option is anaerobic-aerobic sequence (AAS) bioreactors, which use an anaerobic pretreatment step (e.g., anaerobic hybrid reactors) to reduce carbon levels, followed by some form of aerobic treatment. Although AAS is common in warm climates, it is not known how its compares to other treatment options relative to disease transmission, including its influence on antibiotic resistance (AR) in treated effluents. Here, we used metagenomic approaches to contrast the fate of antibiotic-resistant genes (ARG) in anaerobic, aerobic, and AAS bioreactors treating domestic wastewater. Five reactor configurations were monitored for 6 months, and treatment performance, energy use, and ARG abundance and diversity were compared in influents and effluents. AAS and aerobic reactors were superior to anaerobic units in reducing ARG-like sequence abundances, with effluent ARG levels of 29, 34, and 74 ppm (198 ppm influent), respectively. AAS and aerobic systems especially reduced aminoglycoside, tetracycline, and β-lactam ARG levels relative to anaerobic units, although 63 persistent ARG subtypes were detected in effluents from all systems (of 234 assessed). Sulfonamide and chloramphenicol ARG levels were largely unaffected by treatment, whereas a broad shift from target-specific ARGs to ARGs associated with multi-drug resistance was seen across influents and effluents. AAS reactors show promise for future applications because they can reduce more ARGs for less energy (32% less energy here), but all three treatment options have limitations and need further study.

Energy efficiency improvement potentials and a low energy demand scenario for the global industrial sector

NARCIS (Netherlands)

Kermeli, Katerina; Graus, Wina H J; Worrell, Ernst

2014-01-01

The adoption of energy efficiency measures can significantly reduce industrial energy use. This study estimates the future industrial energy consumption under two energy demand scenarios: (1) a reference scenario that follows business as usual trends and (2) a low energy demand scenario that takes

Energy conservation and environmental benefits that may be realized from Superconducting Magnetic Energy Storage

International Nuclear Information System (INIS)

Baumann, P.D.

1992-01-01

This paper discusses the Superconducting Magnetic Energy Storage (SMES) technology which has the capability to significantly improve electrical system operations within electric utility systems. This has been demonstrated by Bonneville Power Administration in a 30-MJ SMES demonstration unit. Savings in utility operations from improved system efficiency, increased reliability, and reduced maintenance requirements contribute to the economic justification of SMES. Beyond these benefits, there are additional benefits which in the long run may significantly outweigh the electrical operational benefits. These benefits are the energy conservation and environmental benefits. Since SMES can uncouple generation from load, it can shift generation around, thereby changing the operational characteristics of the system. The technology has the capability of reducing fuel consumption which can in turn reduce emissions. In a regional setting it can potentially shift emissions both in volumes and in physical areas to avoid problem situations. With its capability to strategically shift generation and significantly affect emissions and air quality it can stretch clean energy generation options. With these attributes, SMES can be recognized as an energy and environmental management technology and tool

Boise, Idaho: Improving Air Quality through Alternative Fuels & Reduced Vehicular Travel (City Energy: From Data to Decisions)

Energy Technology Data Exchange (ETDEWEB)

Strategic Priorities and Impact Analysis Team, Office of Strategic Programs

2017-11-01

This fact sheet "Boise, Idaho: Improving Air Quality through Alternative Fuels & Reduced Vehicular Travel" explains how the City of Boise used data from the U.S. Department of Energy's Cities Leading through Energy Analysis and Planning (Cities-LEAP) and the State and Local Energy Data (SLED) programs to inform its city energy planning. It is one of ten fact sheets in the "City Energy: From Data to Decisions" series.

An evaluation of the impact of reducing energy subsidies on living expenses of households

International Nuclear Information System (INIS)

Saboohi, Y.

2001-01-01

A policy of subsidizing energy has been pursued in the Islamic Republic of Iran to help the poor and to utilize the relative advantages of the country. But it has been realized that energy subsidy has led to market distortion and welfare loss. Hence, elimination of energy subsidy is considered as a crucial matter. Changes in energy policy are hindered by the uncertainty on the impact of reducing energy subsidy on the living expenses of population. In the present article the distribution of resources through energy subsidy is evaluated; and the direct and indirect effect of eliminating energy subsidies on the living expenses is estimated with the help of an analytical tool that has been developed. It is then concluded that additional financial resources obtained from reduction of energy subsidies could be allocated for compensating the decrease in purchasing power of households. The results of analysis reveal that more egalitarian distribution of resources and helping the poor could be achieved through implementation of a progressive policy of social security that is supported by financial resources available from elimination of energy subsidies. (author)

Nordic Energy Technologies : Enabling a sustainable Nordic energy future

Energy Technology Data Exchange (ETDEWEB)

Vik, Amund; Smith, Benjamin

2009-10-15

A high current Nordic competence in energy technology and an increased need for funding and international cooperation in the field are the main messages of the report. This report summarizes results from 7 different research projects relating to policies for energy technology, funded by Nordic Energy Research for the period 2007-2008, and provides an analysis of the Nordic innovation systems in the energy sector. The Nordic countries possess a high level of competence in the field of renewable energy technologies. Of the total installed capacity comprises a large share of renewable energy, and Nordic technology companies play an important role in the international market. Especially distinguished wind energy, both in view of the installed power and a global technology sales. Public funding for energy research has experienced a significant decline since the oil crisis of the 1970s, although the figures in recent years has increased a bit. According to the IEA, it will require a significant increase in funding to reduce greenhouse gas emissions and limit further climate change. The third point highlighted in the report is the importance of international cooperation in energy research. Nordic and international cooperation is necessary in order to reduce duplication and create the synergy needed if we are to achieve our ambitious policy objectives in the climate and energy issue. (AG)

An assessment of available measures to reduce traction energy use in railway networks

International Nuclear Information System (INIS)

Douglas, Heather; Roberts, Clive; Hillmansen, Stuart; Schmid, Felix

2015-01-01

Highlights: • Railway networks are defined in terms of their distinguishing features. • Current energy saving measures are reviewed and categorised by the energy use they target. • The achievable energy savings of different measures are compared dependent on the network type. • The success of a measure depends on the characteristics of the network, vehicle and service. • Measures should be evaluated at system level due to interdependencies. - Abstract: Rail is becoming an increasingly popular choice to satisfy transportation demands locally, nationally and internationally, due to its inherent efficiency and high capacity. Despite this, operators are facing pressure to reduce rail energy consumption to meet efficiency targets, whilst still maintaining service quality and managing increased demand. A number of individual measures have been proposed to reduce energy in the rail sector, often showing good results on specific case studies. It is generally agreed that the attainable savings of a given measure change dependant on the route, vehicle and service characteristics. However, there is little information in the literature specifically regarding which measures are most suitable for given network types, or how they interact. This paper therefore aims to begin evaluating the available measures in terms of their suitability for different systems. Firstly, networks are defined in terms of their distinguishing features. As traction accounts for the majority of all energy use in the rail sector, the traction flow through a vehicle is considered as the starting point for an evaluation of measures. Current technologies and procedures are reviewed and categorised based on which area of traction use they target. Thought is given to the factors that affect implementation and the networks where they are applied. A key output of this paper is a comparison of the achievable energy savings of different measures dependent on the network type. It is hoped that this will

Shortening Delivery Times of Intensity Modulated Proton Therapy by Reducing Proton Energy Layers During Treatment Plan Optimization

Energy Technology Data Exchange (ETDEWEB)

Water, Steven van de, E-mail: s.vandewater@erasmusmc.nl [Department of Radiation Oncology, Erasmus MC Cancer Institute, Rotterdam (Netherlands); Kooy, Hanne M. [F. H. Burr Proton Therapy Center, Department of Radiation Oncology, Massachusetts General Hospital and Harvard Medical School, Boston, Massachusetts (United States); Heijmen, Ben J.M.; Hoogeman, Mischa S. [Department of Radiation Oncology, Erasmus MC Cancer Institute, Rotterdam (Netherlands)

2015-06-01

Purpose: To shorten delivery times of intensity modulated proton therapy by reducing the number of energy layers in the treatment plan. Methods and Materials: We have developed an energy layer reduction method, which was implemented into our in-house-developed multicriteria treatment planning system “Erasmus-iCycle.” The method consisted of 2 components: (1) minimizing the logarithm of the total spot weight per energy layer; and (2) iteratively excluding low-weighted energy layers. The method was benchmarked by comparing a robust “time-efficient plan” (with energy layer reduction) with a robust “standard clinical plan” (without energy layer reduction) for 5 oropharyngeal cases and 5 prostate cases. Both plans of each patient had equal robust plan quality, because the worst-case dose parameters of the standard clinical plan were used as dose constraints for the time-efficient plan. Worst-case robust optimization was performed, accounting for setup errors of 3 mm and range errors of 3% + 1 mm. We evaluated the number of energy layers and the expected delivery time per fraction, assuming 30 seconds per beam direction, 10 ms per spot, and 400 Giga-protons per minute. The energy switching time was varied from 0.1 to 5 seconds. Results: The number of energy layers was on average reduced by 45% (range, 30%-56%) for the oropharyngeal cases and by 28% (range, 25%-32%) for the prostate cases. When assuming 1, 2, or 5 seconds energy switching time, the average delivery time was shortened from 3.9 to 3.0 minutes (25%), 6.0 to 4.2 minutes (32%), or 12.3 to 7.7 minutes (38%) for the oropharyngeal cases, and from 3.4 to 2.9 minutes (16%), 5.2 to 4.2 minutes (20%), or 10.6 to 8.0 minutes (24%) for the prostate cases. Conclusions: Delivery times of intensity modulated proton therapy can be reduced substantially without compromising robust plan quality. Shorter delivery times are likely to reduce treatment uncertainties and costs.

Reducing the energy consumption of an earth–air heat exchanger with a PID control system

International Nuclear Information System (INIS)

Diaz-Mendez, S.E.; Patiño-Carachure, C.; Herrera-Castillo, J.A.

2014-01-01

Highlights: • The application of control actions to green technologies has been simulated. • Energy consumption of green technologies can be reduced even more. • The efficiency of green technologies can be raised. • Environmental concerns can be diminished. • The sustainability of the planet can be increased. - Abstract: Reducing environmental emissions is one of the challenges that human being has to overcome. It can only be reached with a proper energetic efficiency and management of the processes that exist in the society nowadays. Several academic works have mentioned that raising the efficiency of a process it also increases sustainability and in turn decreases the environmental impact. One process that requires much attention is the cooling and heating of buildings; this process contributes to the major part of the electric bill, in particular, if a conventional and old air conditioning is used as commonly occurs in many countries. In recent years there have been developed new alternatives that are used in few countries, such as the earth–air heat exchanger, where air is passed through a heat exchanger buried a few meters below the ground. The heat exchanger takes advantage of the well-known difference between the temperature of the surrounding air and the temperature of the ground for cooling or heating the air that is subsequently injected into the buildings. This process requires less energy, then in the present work is thought that a PID (Proportional, Integral and Derivative) controller can be applied to an earth–air heat exchanger to reduce even more the energy consumption. Therefore, a simulation of a thermodynamic model of an earth–air heat exchanger was done and used along with a PID controller, to estimate savings in energy consumption. The results show that the energy consumption can be reduced up to 87% with the PID control, hence the efficiency of the process is increased as well as the sustainability of the planet and thus the

Synthesis and Summary Report on State of the Art, Drivers and Stakeholders of Energy Efficiency in Agricullture, and Potential of Energy Saving Measures

NARCIS (Netherlands)

Visser, de C.L.M.; Buisonje, de F.E.; Ellen, H.H.; Stanghellini, C.; Voort, van der M.P.J.

2012-01-01

Improvements in the energy efficiency of agricultural production have the potential to significantly reduce energy inputs and thereby reducing production costs and greenhouse gas emissions. Energy efficiency analysis depicts the distribution of energy inputs in a given agricultural production system

How effective are energy efficiency and renewable energy in curbing CO2 emissions in the long run? A heterogeneous panel data analysis

International Nuclear Information System (INIS)

Özbuğday, Fatih Cemil; Erbas, Bahar Celikkol

2015-01-01

Energy efficiency and renewable energy are considered to be two indispensable solutions to control GHG (greenhouse gas) emissions. Moreover, industrialization is at the center of discussions on the roles of countries to reduce CO 2 emissions. However, the literature is underprovided to understand the long run contribution of energy efficiency, renewable energy and industrial composition in reducing GHG emissions at the macro level. In this study, we differentiate the effects of economic activity, energy efficiency, economic structure and use of renewable energy resources on CO 2 emissions. We develop energy efficiency indices for thirty six countries for the period of 1971–2009 and use a CCE (common correlated effects) estimator model that is consistent under heterogeneity and cross-sectional dependence. We find a positive significant effect of energy efficiency on CO 2 emissions in the long-run. Similarly, substituting renewable energy for non-renewable energy reduces CO 2 emissions in the long-run. Our results ensure widely discussed roles of energy efficiency and renewable energy in curbing CO 2 emissions. Furthermore, the scale of economic activity measured by real income and industrialization have significant positive effect on CO 2 emissions. - Highlights: • We model long-run effects of energy efficiency and renewable energy on CO 2 . • Energy efficiency significantly reduces CO 2 emissions over the long term. • Replacing non-renewable energy sources with renewable ones reduces CO 2 emissions. • CO 2 emissions rise with increases in real income. • Industrial composition affects CO 2 emissions

Enhanced charge efficiency and reduced energy use in capacitive deionization by increasing the discharge voltage.

Science.gov (United States)

Kim, T; Dykstra, J E; Porada, S; van der Wal, A; Yoon, J; Biesheuvel, P M

2015-05-15

Capacitive deionization (CDI) is an electrochemical method for water desalination using porous carbon electrodes. A key parameter in CDI is the charge efficiency, Λ, which is the ratio of salt adsorption over charge in a CDI-cycle. Values for Λ in CDI are typically around 0.5-0.8, significantly less than the theoretical maximum of unity, due to the fact that not only counterions are adsorbed into the pores of the carbon electrodes, but at the same time coions are released. To enhance Λ, ion-exchange membranes (IEMs) can be implemented. With membranes, Λ can be close to unity because the membranes only allow passage for the counterions. Enhancing the value of Λ is advantageous as this implies a lower electrical current and (at a fixed charging voltage) a reduced energy use. We demonstrate how, without the need to include IEMs, the charge efficiency can be increased to values close to the theoretical maximum of unity, by increasing the cell voltage during discharge, with only a small loss of salt adsorption capacity per cycle. In separate constant-current CDI experiments, where after some time the effluent salt concentration reaches a stable value, this value is reached earlier with increased discharge voltage. We compare the experimental results with predictions of porous electrode theory which includes an equilibrium Donnan electrical double layer model for salt adsorption in carbon micropores. Our results highlight the potential of modified operational schemes in CDI to increase charge efficiency and reduce energy use of water desalination. Copyright © 2014 Elsevier Inc. All rights reserved.

Mobile operators have set ambitious targets – Is it possible to boost network capacity while reducing its energy consumption?

DEFF Research Database (Denmark)

Micallef, Gilbert; Mogensen, Preben; Scheck, Hans-Otto

2012-01-01

While operators have to upgrade the capacity of their networks, they have committed themselves to reduce their CO2 emissions, partly by reducing their energy consumption. This article investigates the challenges faced by operators and quantifies, through a number of case studies, the impact...... the possible savings by adopting an energy-efficient capacity evolution together with an equipment replacement and site upgrade strategy. Results show that network operators can get relatively close to their targets, with energy reductions of up to 40% noted. While this can be improved further through software...... based energy saving features, further CO2 emissions can be offset through carbon-neutral energy sources....

Single-source dual-energy spectral multidetector CT of pancreatic adenocarcinoma: optimization of energy level viewing significantly increases lesion contrast.

Science.gov (United States)

Patel, B N; Thomas, J V; Lockhart, M E; Berland, L L; Morgan, D E

2013-02-01

.007). Significantly increased pancreatic lesion contrast was noted at lower viewing energies using spectral MDCT. Individual patient CNR-optimized energy level images have the potential to improve lesion conspicuity. Copyright © 2012 The Royal College of Radiologists. Published by Elsevier Ltd. All rights reserved.

Empowering Sedentary Adults to Reduce Sedentary Behavior and Increase Physical Activity Levels and Energy Expenditure: A Pilot Study

Directory of Open Access Journals (Sweden)

Faisal A. Barwais

2015-01-01

Full Text Available Objective: The purpose of this study was to assess the effectiveness of a 4-week intervention in which an online personal activity monitor (Gruve-Technologies™ was used to reduce sedentary behavior among sedentary adults. Method: Eighteen, sedentary adult volunteers (12 men, six women, mean age 29 ± 4.0 years were recruited to participate in the study. Time spent in sedentary activities and light-, moderate-, and vigorous-intensity physical activity and energy expenditure were assessed during waking hours using the monitor and the 7-day SLIPA Log at both baseline and post-intervention. Results: A significant decrease of 33% (3.1 h/day; p < 0.001 was found between the time spent in sedentary activities measured at baseline (9.4 ± 1.1 h/day and at the end of the 4-week intervention (6.3 ± 0.8 h/day. Consequent to the changes in sedentary time, significant increases were found in the amount of time spent in light- (45% (2.6 h/day, p < 0.001, moderate- (33% (1 h/day p < 0.001, vigorous-intensity physical activity (39% (0.16 h/day, p < 0.001, and energy expenditure (47% (216.7 kcal/day, p < 0.001. Conclusion: This monitor contributes to a meaningful reduction in time spent in sedentary activities and has a large effect on energy expenditure and physical activity patterns.

A significant shift in favor of nuclear energy since 2005

International Nuclear Information System (INIS)

Anon.

2008-01-01

A new opinion poll shows a general trend in Europe in favor of nuclear energy: 44% of the people interrogated are for nuclear energy while only 37% were for in 2005. About 40% of the people against nuclear energy would change their mind if a safe and definitive solution for the management of radioactive waste was found. The survey also shows that more people are aware of the assets of nuclear energy in terms of energy independence and greenhouse gas emission. The countries where the support is the strongest are the Czech Republic (64%), Lithuania (64%), Sweden (62%) and Finland (61%). In France, the biggest nuclear energy producer in Europe, the rate of favorable opinion for nuclear energy remains constant at 52%. (A.C.)

A ‘Carbon Saving Multiplier’ as an alternative to rebound in considering reduced energy supply chain requirements from energy efficiency?

International Nuclear Information System (INIS)

Turner, Karen; Katris, Antonios

2017-01-01

A growing area of research into rebound effects from increased energy efficiency involves application of demand-driven input-output models to consider indirect energy consumption effects associated with re-spending decisions by households with reduced energy spending requirements. However, there is often a lack of clarity in applied studies as to how indirect effects involving energy use and/or carbon emissions in supply chains of both energy and non-energy goods and services have been calculated. We propose that more transparency for policymakers may be introduced by replacing consideration of what are often referred to as ‘indirect rebound’ effects with a simple Carbon Saving Multiplier metric. We illustrate using results from a demand-driven input-output model that tracks supply chain activity at national and/or global level. We argue that this captures and conveys the same information on quantity adjustments in energy used in supply chain activity but does so in a manner that is more positive, transparent, understandable and useful for a policy audience. This is achieved by focusing (here via carbon emissions) on the net benefits of changes in different types of energy use at both household and supply chain levels when energy efficiency improves in households. - Highlights: • Considers energy supply adjustments when household energy efficiency improves. • Focuses on energy supply chain impacts that may offset direct rebound effects. • Carbon Saving Multiplier proposed as a useful indicator of net energy use benefits.

Opportunities to improve energy efficiency and reduce greenhouse gas emissions in the US pulp and paper industry

Energy Technology Data Exchange (ETDEWEB)

Martin, Nathan; Anglani, N.; Einstein, D.; Khrushch, M.; Worrell, E.; Price, L.K.

2000-07-01

The pulp and paper industry accounts for over 12% of total manufacturing energy use in the US (US EIA 1997a), contributing 9% to total manufacturing carbon dioxide emissions. In the last twenty-five years primary energy intensity in the pulp and paper industry has declined by an average of 1% per year. However, opportunities still exist to reduce energy use and greenhouse gas emissions in the manufacture of paper in the US This report analyzes the pulp and paper industry (Standard Industrial Code (SIC) 26) and includes a detailed description of the processes involved in the production of paper, providing typical energy use in each process step. We identify over 45 commercially available state-of-the-art technologies and measures to reduce energy use and calculate potential energy savings and carbon dioxide emissions reductions. Given the importance of paper recycling, our analysis examines two cases. Case A identifies potential primary energy savings without accounting for an increase in recycling, while Case B includes increasing paper recycling. In Case B the production volume of pulp is reduced to account for additional pulp recovered from recycling. We use a discount rate of 30% throughout our analysis to reflect the investment decisions taken in a business context. Our Case A results indicate that a total technical potential primary energy savings of 31% (1013 PJ) exists. For case A we identified a cost-effective savings potential of 16% (533 PJ). Carbon dioxide emission reductions from the energy savings in Case A are 25% (7.6 MtC) and 14% (4.4 MtC) for technical and cost-effective potential, respectively. When recycling is included in Case B, overall technical potential energy savings increase to 37% (1215 PJ) while cost-effective energy savings potential is 16%. Increasing paper recycling to high levels (Case B) is nearly cost-effective assuming a cut-off for cost-effectiveness of a simple payback period of 3 years. If this measure is included, then the

Economic implications of reducing carbon emissions from energy use and industrial processes in Brazil.

Science.gov (United States)

Chen, Y-H Henry; Timilsina, Govinda R; Landis, Florian

2013-11-30

This study assesses the economy-wide impacts of cutting CO2 emissions on the Brazilian economy. It finds that in 2040, the business-as-usual CO2 emissions from energy use and industrial processes would be almost three times as high as those in 2010 and would account for more than half of total national CO2 emissions. The current policy aims to reduce deforestation by 70 percent by 2017 and lower emissions intensity of the overall economy by 36-39 percent by 2020. If the policy were implemented as planned and continued to 2040, there would be no need to cut CO2 emissions from energy use and industrial processes until 2035, as emissions reduction through controlling deforestation would be enough to meet the voluntary carbon mitigation target of Brazil. The study also finds that using the carbon tax revenue to subsidize wind power can effectively increase the country's wind power output if that is the policy priority. Further, it finds evidence supporting the double dividend hypothesis, i.e., using revenue from a hypothetical carbon tax to finance a cut in labor income tax can significantly lower the GDP impacts of the carbon tax. Copyright © 2013 Elsevier Ltd. All rights reserved.

Use of Local Intelligence to Reduce Energy Consumption of Wireless Sensor Nodes in Elderly Health Monitoring Systems

Directory of Open Access Journals (Sweden)

Thomas J. Lampoltshammer

2014-03-01

Full Text Available The percentage of elderly people in European countries is increasing. Such conjuncture affects socio-economic structures and creates demands for resourceful solutions, such as Ambient Assisted Living (AAL, which is a possible methodology to foster health care for elderly people. In this context, sensor-based devices play a leading role in surveying, e.g., health conditions of elderly people, to alert care personnel in case of an incident. However, the adoption of such devices strongly depends on the comfort of wearing the devices. In most cases, the bottleneck is the battery lifetime, which impacts the effectiveness of the system. In this paper we propose an approach to reduce the energy consumption of sensors’ by use of local sensors’ intelligence. By increasing the intelligence of the sensor node, a substantial decrease in the necessary communication payload can be achieved. The results show a significant potential to preserve energy and decrease the actual size of the sensor device units.

Use of Local Intelligence to Reduce Energy Consumption of Wireless Sensor Nodes in Elderly Health Monitoring Systems

Science.gov (United States)

Lampoltshammer, Thomas J.; de Freitas, Edison Pignaton; Nowotny, Thomas; Plank, Stefan; da Costa, João Paulo Carvalho Lustosa; Larsson, Tony; Heistracher, Thomas

2014-01-01

The percentage of elderly people in European countries is increasing. Such conjuncture affects socio-economic structures and creates demands for resourceful solutions, such as Ambient Assisted Living (AAL), which is a possible methodology to foster health care for elderly people. In this context, sensor-based devices play a leading role in surveying, e.g., health conditions of elderly people, to alert care personnel in case of an incident. However, the adoption of such devices strongly depends on the comfort of wearing the devices. In most cases, the bottleneck is the battery lifetime, which impacts the effectiveness of the system. In this paper we propose an approach to reduce the energy consumption of sensors' by use of local sensors' intelligence. By increasing the intelligence of the sensor node, a substantial decrease in the necessary communication payload can be achieved. The results show a significant potential to preserve energy and decrease the actual size of the sensor device units. PMID:24618777

The Effect of Varying Ultrafast Pulse Laser Energies on the Electrical Properties of Reduced Graphene Oxide Sheets in Solution

Science.gov (United States)

Ibrahim, Khaled H.; Irannejad, Mehrdad; Wales, Benjamin; Sanderson, Joseph; Musselman, Kevin P.; Yavuz, Mustafa

2018-02-01

Laser treatment of graphene oxide solution among other techniques is a well-established technique for producing reduced graphene sheets. However, production of high-quality ultra-low sheet resistance reduced graphene oxide (rGO) sheets in solution has been a challenge due to their high degree of randomness, defect-rich medium, and lack of controlability. Recent studies lack an in-depth analytic comparison of laser treatment parameters that yield the highest quality rGO sheets with a low defect ratio. Hence, in this study, we implement a comprehensive comparison of laser treatment parameters and their effect on the yielded rGO sheets from an electronic and physical standpoint. Ultra-low sheet resistance graphene oxide sheets were fabricated using ultrafast laser irradiation with different laser pulse energies in the range of 0.25-2 mJ. Laser treatment for 10 min using a pulse energy of 1 mJ resulted in an increase in the defect spacing, accompanied by a large red shift in the optical absorption of the C=C bond, indicating significant restoration of the s p 2 carbon bonds. These enhancements resulted in a significant reduction in the electrical resistance of the rGO flakes (up to 2 orders of magnitude), raising the electron mobility of the films produced using the irradiated graphene oxide a step closer to that of pristine graphene films. From this study, we can also deduce which exposure regimes result in the fabrication of quantum dots and continuous defect-free films.

Possibilities for reducing CO2 emissions by rational energy used as viewed by enterprises

International Nuclear Information System (INIS)

Preuss, H.J.

1993-01-01

From the view of the industry, energy conservation offers many options for CO 2 reduction. CO 2 reduction in electric power generation is particularly important. The global CO 2 problem cannot be solved by any single measure, but international efforts are required in all production and consumption sectors. Providing energy for the growing world population while at the same time reducing CO 2 is one of the biggest challenges ever faced by mankind. (orig./UA) [de

System dynamics analysis of strategies to reduce energy use in aluminum-intensive sectors

Energy Technology Data Exchange (ETDEWEB)

Hanes, Rebecca J.; Nicholson, Scott; 25-29 June 2017, Carpenter, Alberta

2017-07-13

Aluminum is one of the most widely used materials in industry, with applications in buildings, vehicles, aircraft, and consumer products. Its ubiquity is also on the rise: aluminum is beginning to supplant steel in lightweight vehicles and aircraft, and is used in many green or LEED-certified buildings. Although aluminum tends to be highly recycled, particularly by manufacturers of aluminum products, the sector as a whole is still far from a closed system. As a result, the increase in aluminum consumption also means an increase in primary aluminum production-an energy-intensive process-and an increase in consumption of the raw material bauxite, which in the U.S. is almost entirely imported. Our objectives for this study are to identify and analyze aluminum sector technologies and practices that reduce the energy required to manufacture aluminum products and reduce U.S. dependence on imported aluminum and bauxite. To accomplish these objectives, we will develop a system dynamics (SD) model of aluminum production, use and recycling in key application areas, including aerospace, ground vehicles and consumer products. The model will cover the entire aluminum supply chain as it exists in the U.S., from bauxite importing and refining, to the manufacture of products, to the product use phase and end-of-life processing steps. Aluminum flows throughout the model will be determined by the annual domestic demand for each application area as well as demand projections that extend to 2030. Energy consumption will be tracked based on the flows of aluminum through each step of the supply chain. Using the SD model, we will evaluate several technologies and practices that have the potential to reduce energy consumption and reliance on imported bauxite. These include implementation of advanced primary aluminum production technologies, increased recycling within and between application areas, increased material efficiency and increased product lifetimes. Each of these strategies

Framework for Energy Neutral Treatment for the 21st Century Through Energy Efficient Aeration (WERF Report INFR2R12)

Science.gov (United States)

Aeration is commonly identified as the most significant energy use in the treatment of wastewater and therefore garners significant focus in reducing energy use in the ultimate aspirational goal of achieving net energy neutrality for water resource recovery. This research establi...

Energy use in Denmark

International Nuclear Information System (INIS)

Schipper, L.; Howarth, R.; Andersson, B.; Price, L.

1993-01-01

This paper reviews the evolution of energy use in Denmark since the early 1970s, in order to shed light on the future path of energy use in Denmark, with particular emphasis on the role of energy efficiency. Improvements in end-use energy efficiency reduced primary energy requirements in Denmark by 22% between 1972 and 1988. This change accounts for two thirds of the decline in the ratio of energy use to gross domestic product that occurred during this time: the rest of the decline was caused by changes in the mix of goods and services produced and consumed by the Danes. Total energy savings achieved between 1972 and 1988 in Denmark ranked among the highest measured in any major OECD country. Overall, most of the energy savings in Denmark were brought about through improvements in technology. Short-term changes in consumer behaviour were significant in reducing energy needs for space heating and transport. An important stimulus for improved efficiency was higher energy prices, led in no small part by significant taxes imposed on small consumers of heating oil, electricity and motor fuels. (author). 21 refs, 20 figs, 2 tabs

Iron oxide/aluminum/graphene energetic nanocomposites synthesized by atomic layer deposition: Enhanced energy release and reduced electrostatic ignition hazard

Energy Technology Data Exchange (ETDEWEB)

Yan, Ning; Qin, Lijun [Laboratory of Material Surface Engineering and Nanofabrication, Xi’an Modern Chemistry Research Institute, Shaanxi (China); Science and Technology on Combustion and Explosion Laboratory, Xi’an Modern Chemistry Research Institute, Shaanxi (China); Hao, Haixia [Science and Technology on Combustion and Explosion Laboratory, Xi’an Modern Chemistry Research Institute, Shaanxi (China); Hui, Longfei [Laboratory of Material Surface Engineering and Nanofabrication, Xi’an Modern Chemistry Research Institute, Shaanxi (China); Science and Technology on Combustion and Explosion Laboratory, Xi’an Modern Chemistry Research Institute, Shaanxi (China); Zhao, Fengqi [Science and Technology on Combustion and Explosion Laboratory, Xi’an Modern Chemistry Research Institute, Shaanxi (China); Feng, Hao, E-mail: fenghao98@hotmail.com [Laboratory of Material Surface Engineering and Nanofabrication, Xi’an Modern Chemistry Research Institute, Shaanxi (China); State Key Laboratory of Fluorine and Nitrogen Chemicals, Xi’an Modern Chemistry Research Institute, Shaanxi (China)

2017-06-30

Highlights: • Energetic rGO/Al@Fe{sub 2}O{sub 3}nanocompositeswerefabricatedbyatomiclayerdepositionapproach. • A novel Al@Fe{sub 2}O{sub 3} unit featuring core-shell structure was decorated on the graphene nanosheet. • RGO/Al@Fe{sub 2}O{sub 3} nanocomposite exhibits superior energy release and reduced electrostatic ignition hazard. - Abstract: Nanocomposites consisting of iron oxide (Fe{sub 2}O{sub 3}) and nano-sized aluminum (Al), possessing outstanding exothermic redox reaction characteristics, are highly promising nanothermite materials. However, the reactant diffusion inhibited in the solid state system makes the fast and complete energy release very challenging. In this work, Al nanoparticles anchored on graphene oxide (GO/Al) was initially prepared by a solution assembly approach. Fe{sub 2}O{sub 3} was deposited on GO/Al substrates by atomic layer deposition (ALD). Simultaneously thermal reduction of GO occurs, resulting in rGO/Al@Fe{sub 2}O{sub 3} energetic composites. Differential scanning calorimetry (DSC) analysis reveals that rGO/Al@Fe{sub 2}O{sub 3} composite containing 4.8 wt% of rGO exhibits a 50% increase of the energy release compared to the Al@Fe{sub 2}O{sub 3} nanothermite synthesized by ALD, and an increase of about 130% compared to a random mixture of rGO/Al/Fe{sub 2}O{sub 3} nanoparticles. The enhanced energy release of rGO/Al@Fe{sub 2}O{sub 3} is attributed to the improved spatial distribution as well as the increased interfacial intimacy between the oxidizer and the fuel. Moreover, the rGO/Al@Fe{sub 2}O{sub 3} composite with an rGO content of 9.6 wt% exhibits significantly reduced electrostatic discharge sensitivity. These findings may inspire potential pathways for engineering energetic nanocomposites with enhanced energy release and improved safety characteristics.

Iron oxide/aluminum/graphene energetic nanocomposites synthesized by atomic layer deposition: Enhanced energy release and reduced electrostatic ignition hazard

International Nuclear Information System (INIS)

Yan, Ning; Qin, Lijun; Hao, Haixia; Hui, Longfei; Zhao, Fengqi; Feng, Hao

2017-01-01

Highlights: • Energetic rGO/Al@Fe 2 O 3 nanocompositeswerefabricatedbyatomiclayerdepositionapproach. • A novel Al@Fe 2 O 3 unit featuring core-shell structure was decorated on the graphene nanosheet. • RGO/Al@Fe 2 O 3 nanocomposite exhibits superior energy release and reduced electrostatic ignition hazard. - Abstract: Nanocomposites consisting of iron oxide (Fe 2 O 3 ) and nano-sized aluminum (Al), possessing outstanding exothermic redox reaction characteristics, are highly promising nanothermite materials. However, the reactant diffusion inhibited in the solid state system makes the fast and complete energy release very challenging. In this work, Al nanoparticles anchored on graphene oxide (GO/Al) was initially prepared by a solution assembly approach. Fe 2 O 3 was deposited on GO/Al substrates by atomic layer deposition (ALD). Simultaneously thermal reduction of GO occurs, resulting in rGO/Al@Fe 2 O 3 energetic composites. Differential scanning calorimetry (DSC) analysis reveals that rGO/Al@Fe 2 O 3 composite containing 4.8 wt% of rGO exhibits a 50% increase of the energy release compared to the Al@Fe 2 O 3 nanothermite synthesized by ALD, and an increase of about 130% compared to a random mixture of rGO/Al/Fe 2 O 3 nanoparticles. The enhanced energy release of rGO/Al@Fe 2 O 3 is attributed to the improved spatial distribution as well as the increased interfacial intimacy between the oxidizer and the fuel. Moreover, the rGO/Al@Fe 2 O 3 composite with an rGO content of 9.6 wt% exhibits significantly reduced electrostatic discharge sensitivity. These findings may inspire potential pathways for engineering energetic nanocomposites with enhanced energy release and improved safety characteristics.

Combining climate and energy policies: synergies or antagonism? Modeling interactions with energy efficiency instruments

International Nuclear Information System (INIS)

Lecuyer, Oskar; Bibas, Ruben

2012-01-01

In addition to the already present Climate and Energy package, the European Union (EU) plans to include a binding target to reduce energy consumption. We analyze the rationales the EU invokes to justify such an overlapping and develop a minimal common framework to study interactions arising from the combination of instruments reducing emissions, promoting renewable energy (RE) production and reducing energy demand through energy efficiency (EE) investments. We find that although all instruments tend to reduce GHG emissions and although a price on carbon tends also to give the right incentives for RE and EE, the combination of more than one instrument leads to significant antagonisms regarding major objectives of the policy package. The model allows to show in a single framework and to quantify the antagonistic effects of the joint promotion of RE and EE. We also show and quantify the effects of this joint promotion on ETS permit price, on wholesale market price and on energy production levels. (authors)

Power-generating process of obtaining gas-energy carrier and reducer from coal

International Nuclear Information System (INIS)

Tleugabulov, S.; Duncheva, E.; Zubkevich, M.

1999-01-01

The manufacture of power-generating gas has the important economic value for Kazakhstan having large territory, raw and fuel resources especially power coal and clean coal wastes. The technology of reception of gas-energy carrier and reducer from power coal is developed. The basic product of technological process is heated reducing gas. Reducing potential of the gas is characterized by a volumetric share of components (CO+H 2 )-RC in relation to volume of whole mix of gases received with gasification of coal. The value of parameter RC is regulated by a degree of enrichment of air by oxygen r 0 , and the temperature - by the charge of a parity of endothermic reaction in the chamber of gas regeneration. The dependence of the gas structure and temperature on the degree of enrichment of air by oxygen is shown and the circuit of the gas generator is given. (author)

Heuristic Scheduling in Grid Environments: Reducing the Operational Energy Demand

Science.gov (United States)

Bodenstein, Christian

In a world where more and more businesses seem to trade in an online market, the supply of online services to the ever-growing demand could quickly reach its capacity limits. Online service providers may find themselves maxed out at peak operation levels during high-traffic timeslots but too little demand during low-traffic timeslots, although the latter is becoming less frequent. At this point deciding which user is allocated what level of service becomes essential. The concept of Grid computing could offer a meaningful alternative to conventional super-computing centres. Not only can Grids reach the same computing speeds as some of the fastest supercomputers, but distributed computing harbors a great energy-saving potential. When scheduling projects in such a Grid environment however, simply assigning one process to a system becomes so complex in calculation that schedules are often too late to execute, rendering their optimizations useless. Current schedulers attempt to maximize the utility, given some sort of constraint, often reverting to heuristics. This optimization often comes at the cost of environmental impact, in this case CO 2 emissions. This work proposes an alternate model of energy efficient scheduling while keeping a respectable amount of economic incentives untouched. Using this model, it is possible to reduce the total energy consumed by a Grid environment using 'just-in-time' flowtime management, paired with ranking nodes by efficiency.

Energy efficiency optimum strategies for low carbon development in ...

International Development Research Centre (IDRC) Digital Library (Canada)

Sound energy efficiency policies play a critical role in fighting climate change. They are considered vital to reducing energy bills and reducing emissions and air pollution, while also improving energy security and sovereignty, and increasing access to energy. However, there are still significant barriers to the effective ...

Low energy availability in exercising men is associated with reduced leptin and insulin but not with changes in other metabolic hormones.

Science.gov (United States)

Koehler, Karsten; Hoerner, Neele R; Gibbs, Jenna C; Zinner, Christoph; Braun, Hans; De Souza, Mary Jane; Schaenzer, Wilhelm

2016-10-01

Low energy availability, defined as low caloric intake relative to exercise energy expenditure, has been linked to endocrine alterations frequently observed in chronically energy-deficient exercising women. Our goal was to determine the endocrine effects of low energy availability in exercising men. Six exercising men (VO2peak: 49.3 ± 2.4 ml · kg(-1) · min(-1)) underwent two conditions of low energy availability (15 kcal · kg(-1) fat-free mass [FFM] · day(-1)) and two energy-balanced conditions (40 kcal · kg(-1) FFM · day(-1)) in randomised order. During one low energy availability and one balanced condition, participants exercised to expend 15 kcal · kg(-1) FFM · day(-1); no exercise was conducted during the other two conditions. Metabolic hormones were assessed before and after each 4-day period. Following both low energy availability conditions, leptin (-53% to -56%) and insulin (-34% to -38%) were reduced (P exercise (P > 0.80). Low energy availability did not significantly impact ghrelin, triiodothyronine, testosterone and IGF-1 (all P > 0.05). The observed reductions in leptin and insulin were in the same magnitude as changes previously reported in sedentary women. Further research is needed to understand why other metabolic hormones are more robust against low energy availability in exercising men than those in sedentary and exercising women.

Personnel β-dosimetry method for reducing energy dependence

International Nuclear Information System (INIS)

Gesell, T.F.; Jones, D.E.; Gupta, V.P.; Kalbeitzer, F.L.; Cusimano, J.P.

1979-03-01

Current practices for the measurement of skin dose are reviewed and found to be inadequate. The current INEL dosimeter was examined for systematic and random error. Systematic (i.e., variation with energy) error was found to range over a factor of 10 while the random error was reasonably small for the larger β/γ ratios. Other designs with thicker windows as is more common would show even larger systematic errors. Various methods for improving beta dosimetry were reviewed. A new dosimeter design utilizing three chips, each having a window of difference thickness, was proposed. According to the calculations, this dosimeter should markedly reduce systematic error but will introduce somewhat more random error. Preliminary measurements were carried out related to angular dependence and charged particle equilibrium. The proposed dosimeter design was tested with betas from a uranium slab. The average of the seven results was in excellent agreement with the known dose rate and the standard deviation of the result was 16%

Optimisation of a Swedish district heating system with reduced heat demand due to energy efficiency measures in residential buildings

International Nuclear Information System (INIS)

Åberg, M.; Henning, D.

2011-01-01

The development towards more energy efficient buildings, as well as the expansion of district heating (DH) networks, is generally considered to reduce environmental impact. But the combined effect of these two progressions is more controversial. A reduced heat demand (HD) due to higher energy efficiency in buildings might hamper co-production of electricity and DH. In Sweden, co-produced electricity is normally considered to displace electricity from less efficient European condensing power plants. In this study, a potential HD reduction due to energy efficiency measures in the existing building stock in the Swedish city Linköping is calculated. The impact of HD reduction on heat and electricity production in the Linköping DH system is investigated by using the energy system optimisation model MODEST. Energy efficiency measures in buildings reduce seasonal HD variations. Model results show that HD reductions primarily decrease heat-only production. The electricity-to-heat output ratio for the system is increased for HD reductions up to 30%. Local and global CO 2 emissions are reduced. If co-produced electricity replaces electricity from coal-fired condensing power plants, a 20% HD reduction is optimal for decreasing global CO 2 emissions in the analysed DH system. - Highlights: ► A MODEST optimisation model of the Linköping district heating system is used. ► The impact of heat demand reduction on heat and electricity production is examined. ► Model results show that heat demand reductions decrease heat-only production. ► Local and global CO 2 emissions are reduced. ► The system electricity-to-heat output increases for reduced heat demand up to 30%.

HVAC system operational strategies for reduced energy consumption in buildings with intermittent occupancy: The case of mosques

International Nuclear Information System (INIS)

Budaiwi, I.; Abdou, A.

2013-01-01

Highlights: • Proper operational zoning in the early design phase of mosques can lead to up to 30% reduction in the annual cooling energy. • Energy performance index of 71.0 kW h/m 2 yr for an insulated mosque can be realized with A/C proper intermitted operation. • 23% energy saving can be achieved when a properly oversized A/C is operated intermittently for 1 h during each prayer. • 13% reduction in cooling energy use can be achieved when A/C operation precedes worshippers’ occupancy in mosques. • Envelope insulation and A/C intermittent operation with proper operational zoning leads to more than 46% savings in energy. - Abstract: Mosques are places of worship for Muslims with unique functional requirements and operational characteristics. They are partially or fully occupied for about an hour for five intermittent periods during the day. In hot climates, maintaining indoor thermal comfort requires a considerable amount of energy that can be reduced by proper operational zoning and effective HVAC operation strategies. The objective of this paper is to investigate the impact of operational zoning and HVAC system intermittent operation strategies on the energy performance of mosques while thermal comfort is maintained. Energy simulation modeling is used for evaluating alternative zoning and HVAC operation strategies. Results indicate that up to 23% reduction in annual cooling energy is achieved by employing suitable HVAC operation strategy and system over-sizing, and 30% reduction is achieved by appropriate operational zoning. Comparing the cooling energy consumption of HVAC summer continuous operation of an un-insulated mosque with the consumption of the insulated mosque with properly oversized HVAC system operated for 1 h during each prayer, indicated that as much as 46% of cooling energy reduction can be achieved. Furthermore, utilizing proper operational zoning and HVAC operation strategies is expected to bring about an additional significant energy

Solid Fuel - Oxygen Fired Combustion for Production of Nodular Reduced Iron to Reduce CO2 Emissions and Improve Energy Efficiencies

Energy Technology Data Exchange (ETDEWEB)

Donald R. Fosnacht; Richard F. Kiesel; David W. Hendrickson; David J. Englund; Iwao Iwasaki; Rodney L. Bleifuss; Mathew A. Mlinar

2011-12-22

The current trend in the steel industry is an increase in iron and steel produced in electric arc furnaces (EAF) and a gradual decline in conventional steelmaking from taconite pellets in blast furnaces. In order to expand the opportunities for the existing iron ore mines beyond their blast furnace customer base, a new material is needed to satisfy the market demands of the emerging steel industry while utilizing the existing infrastructure and materials handling capabilities. This demand creates opportunity to convert iron ore or other iron bearing materials to Nodular Reduced Iron (NRI) in a recently designed Linear Hearth Furnace (LHF). NRI is a metallized iron product containing 98.5 to 96.0% iron and 2.5 to 4% C. It is essentially a scrap substitute with little impurity that can be utilized in a variety of steelmaking processes, especially the electric arc furnace. The objective of this project was to focus on reducing the greenhouse gas emissions (GHG) through reducing the energy intensity using specialized combustion systems, increasing production and the use of biomass derived carbon sources in this process. This research examined the use of a solid fuel-oxygen fired combustion system and compared the results from this system with both oxygen-fuel and air-fuel combustion systems. The solid pulverized fuels tested included various coals and a bio-coal produced from woody biomass in a specially constructed pilot scale torrefaction reactor at the Coleraine Minerals Research Laboratory (CMRL). In addition to combustion, the application of bio-coal was also tested as a means to produce a reducing atmosphere during key points in the fusion process, and as a reducing agent for ore conversion to metallic iron to capture the advantage of its inherent reduced carbon footprint. The results from this study indicate that the approaches taken can reduce both greenhouse gas emissions and the associated energy intensity with the Linear Hearth Furnace process for converting

COMPANY AIKIDO – IT SEEMS TO BE A PRACTICAL METHOD TO REDUCE STRESS AND INCREASE A PERSON’S ENERGY

Directory of Open Access Journals (Sweden)

Andronicus TORP

2016-05-01

Full Text Available Companies are increasingly using methods such as massage, sports, mindfulness, etc. in order for example to improve employee well-being, reduce stress, or increase the energy level of the employees. This article examines, based on a case study, if Aikido may be a practical way to reduce stress and/or increase energy. The empirical study is based on measuring the energy and stress level of the practitioners before and after the practice of Aikido by the use of the ElectroPhotonic Imaging Device developed by Prof. Dr. Korotkov.

Reduced energy consumption for melting in foundries

Energy Technology Data Exchange (ETDEWEB)

Skov-Hansen, S.

2007-09-15

By improving the gating technology in traditional gating systems it is possible to reduce the amount of metal to be re-melted, and hence reduce the energy consumption for melting in foundries. Traditional gating systems are known for a straight tapered down runner a well base and 90 deg. bends in the runner system. In the streamlined gating systems there are no sharp changes in direction and a large effort is done to confine and control the flow of the molten metal during mould filling. Experiments in real production lines have proven that using streamlined gating systems improves yield by decreasing the poured weight compared to traditional layouts. In a layout for casting of valve housings in a vertically parted mould the weight of the gating system was reduced by 1,1kg which is a 20% weight reduction for the gating system. In a layout for horizontally parted moulds the weight of the gating system has been reduced by 3,7kg which is a weight reduction of 60% for the gating system. The experiments casting valve housings in ductile iron also proved that it is possible to lower the pouring temperature from 1400 deg. C to 1300 deg. C without the risk of cold runs. Glass plate fronted moulds have been used to study the flow of melt during mould filling. These experiments have also been used for studying the flow pattern when ceramic filters are used. The thorough study of the use of filters revealed that the metal passing through the filter is divided into a number of small jets. This proves that filters do not have the claimed positive effect on the flow of metal. The volumes necessary on either side of the filter is not filled till a backpressure is build up and results in formation of pressure shocks when backfilled. These pressure shocks result in more turbulence inside the casting than the same gating system with no filter. Not using filters can mean a reduction in poured weight of 0,6kg. To examine if the experiments using glass plate fronted moulds give

An Analysis of the Use of Energy Audits, Solar Panels, and Wind Turbines to Reduce Energy Consumption from Non Renewable Energy Sources

Science.gov (United States)

2015-04-15

a need to reduce water consumption whenever possible. Congress issued the initial guidelines for flow control in various plumbing products via the...Base • Florida Solar Energy Center ( Cocoa , FL) • Houston County Solid Waste Disposal Facility (Kathleen, GA) Certification CDEP interns each... PRODUCTS · COMPIOP AGG $ 2,000,000 POUCY ~rg: LOC $ ~"’~"~ ~~~INGlE UMIT s All’f AUTO BODILY INJURY (Por pononj $ ........ ~~,~~ BODILY INJURY (Por

Significance of atmospheric effects of heat rejection from energy centers in the semi arid northwest

International Nuclear Information System (INIS)

Ramsdell, J.V.; Drake, R.L.; Young, J.R.

1976-01-01

The results presented in this paper have been obtained using simple atmospheric models in an attempt to optimize heat sink management in a conceptual nuclear energy center (NEC) at Hanford. The models have been designed to be conservatice in the sense that they are biased toward over prediction of the impact of cooling system effluents on humidity and fog. Thus the models are screening tools to be used to identify subjects for further, more realistic examination. Within this context the following conclusions have been reached: the evaluation of any atmospheric impact postulated for heat dissipation must be conducted in quantitative terms which can be used to determine the significance of the impact; of the potential atmospheric impacts of large heat releases from energy centers, the one most amenable to quantitative evaluation in meaningful terms as the increase in fog; a postulated increase in frequency of fog can be translated into terms of visibility and both can be evaluated statistically; the translation of a increase in fog to visibility terms permits economic evaluation of the impact; and the predicted impact of the HNEC on fog and visibility is statistically significant whether the energy center consists of 20 or 40 units

Potential for reducing paper mill energy use and carbon dioxide emissions through plant-wide energy audits: A case study in China

International Nuclear Information System (INIS)

Kong, Lingbo; Price, Lynn; Hasanbeigi, Ali; Liu, Huanbin; Li, Jigeng

2013-01-01

Highlights: ► We audited a paper mill in China to reduce its energy use and CO 2 emissions. ► The energy use and CO 2 emissions of the mill and each paper machine are presented. ► The energy saving potential for the paper machine is estimated at 8–37%. ► The energy saving potential is 967.8 TJ, equal to 14.4% of the mill’s energy use. ► The CO 2 reduction potential is 93,453 tonnes CO 2 for the studied paper mill. -- Abstract: The pulp and paper industry is one of the most energy-intensive industries worldwide. In 2007, it accounted for 5% of total global industrial energy consumption and 2% of direct industrial carbon dioxide (CO 2 ) emissions. An energy audit is a primary step toward improving energy efficiency at the facility level. This paper describes a plant-wide energy audit aimed at identifying energy conservation and CO 2 mitigation opportunities at a paper mill in Guangdong province, China. We describe the energy audit methods, relevant Chinese standards, methods of calculating energy and carbon indicators, baseline energy consumption and CO 2 emissions of the audited paper mill, and nine energy-efficiency improvement opportunities identified by the audit. For each of the nine options, we evaluate the energy conservation and associated CO 2 mitigation potential. The total technical energy conservation potential for these nine opportunities is 967.8 terajoules (TJ), and the total CO 2 mitigation potential is equal to 93,453 tonnes CO 2 annually, representing 14.4% and 14.7%, respectively, of the mill’s total energy consumption and CO 2 emissions during the audit period.

Energy strategy 2050. From coal, oil and gas to green energy; Danish Government's energy policy; Energistrategi 2050 - fra kul, olie og gas til groen energi

Energy Technology Data Exchange (ETDEWEB)

2011-02-15

The Danish Government's ''Energy strategy 2050'' describes how the country can achieve its independence from coal, oil and gas by the year 2050 and significantly reduce its greenhouse gas emissions. The strategy contains a raft of initiatives that will reduce the energy industry's use of fossil fuels by 33 % in 2020, compared with 2009. The reduction will put Denmark well on its way to complete independence of fossil fuels by 2050. The strategy calls for a significant increase in renewable energy obtained from wind, biomass and biogas which over the next decade will increase the share of renewable to 33 % of energy consumption, if the initiatives in the strategy are implemented. The strategy offers an economically responsible path to the conversion of the Danish energy supply, and includes specific initiatives, that are all fully financed and which will not damage the nation's competitiveness. Homeowners will experience moderate increases in the costs of heat and electricity, but will also be given opportunities to lower their energy expenses through greater efficiency. Companies can expect added expenses amounting to 0.1 % of the rise in their gross revenue growth by 2020. (ln)

Opportunities to improve energy efficiency and reduce greenhouse gas emissions in the U.S. pulp and paper industry

Energy Technology Data Exchange (ETDEWEB)

Martin, Nathan; Anglani, N.; Einstein, D.; Khrushch, M.; Worrell, E.; Price, L.K.

2000-07-01

The pulp and paper industry accounts for over 12% of total manufacturing energy use in the U.S. (U.S. EIA 1997a), contributing 9% to total manufacturing carbon dioxide emissions. In the last twenty-five years primary energy intensity in the pulp and paper industry has declined by an average of 1% per year. However, opportunities still exist to reduce energy use and greenhouse gas emissions in the manufacture of paper in the U.S. This report analyzes the pulp and paper industry (Standard Industrial Code (SIC) 26) and includes a detailed description of the processes involved in the production of paper, providing typical energy use in each process step. We identify over 45 commercially available state-of-the-art technologies and measures to reduce energy use and calculate potential energy savings and carbon dioxide emissions reductions. Given the importance of paper recycling, our analysis examines two cases. Case A identifies potential primary energy savings without accounting for an increase in recycling, while Case B includes increasing paper recycling. In Case B the production volume of pulp is reduced to account for additional pulp recovered from recycling. We use a discount rate of 30% throughout our analysis to reflect the investment decisions taken in a business context. Our Case A results indicate that a total technical potential primary energy savings of 31% (1013 PJ) exists. For case A we identified a cost-effective savings potential of 16% (533 PJ). Carbon dioxide emission reductions from the energy savings in Case A are 25% (7.6 MtC) and 14% (4.4 MtC) for technical and cost-effective potential, respectively. When recycling is included in Case B, overall technical potential energy savings increase to 37% (1215 PJ) while cost-effective energy savings potential is 16%. Increasing paper recycling to high levels (Case B) is nearly cost-effective assuming a cut-off for cost-effectiveness of a simple payback period of 3 years. If this measure is included, then

Reducing cooling energy consumption in data centres and critical facilities

Science.gov (United States)

Cross, Gareth

Given the rise of our everyday reliance on computers in all walks of life, from checking the train times to paying our credit card bills online, the need for computational power is ever increasing. Other than the ever-increasing performance of home Personal Computers (PC's) this reliance has given rise to a new phenomenon in the last 10 years ago. The data centre. Data centres contain vast arrays of IT cabinets loaded with servers that perform millions of computational equations every second. It is these data centres that allow us to continue with our reliance on the internet and the PC. As more and more data centres become necessary due to the increase in computing processing power required for the everyday activities we all take for granted so the energy consumed by these data centres rises. Not only are more and more data centres being constructed daily, but operators are also looking at ways to squeeze more processing from their existing data centres. This in turn leads to greater heat outputs and therefore requires more cooling. Cooling data centres requires a sizeable energy input, indeed to many megawatts per data centre site. Given the large amounts of money dependant on the successful operation of data centres, in particular for data centres operated by financial institutions, the onus is predominantly on ensuring the data centres operate with no technical glitches rather than in an energy conscious fashion. This report aims to investigate the ways and means of reducing energy consumption within data centres without compromising the technology the data centres are designed to house. As well as discussing the individual merits of the technologies and their implementation technical calculations will be undertaken where necessary to determine the levels of energy saving, if any, from each proposal. To enable comparison between each proposal any design calculations within this report will be undertaken against a notional data facility. This data facility will

Optimal distributed energy resources and the cost of reduced greenhouse gas emissions in a large retail shopping centre

International Nuclear Information System (INIS)

Braslavsky, Julio H.; Wall, Josh R.; Reedman, Luke J.

2015-01-01

Highlights: • Optimal options for distributed energy resources are analysed for a shopping centre. • A multiobjective optimisation model is formulated and solved using DER-CAM. • Cost and emission trade-offs are compared in four key optimal investment scenarios. • Moderate investment in DER technologies lowers emissions by 29.6% and costs by 8.5%. • Larger investment in DER technologies lowers emissions by 72% at 47% higher costs. - Abstract: This paper presents a case study on optimal options for distributed energy resource (DER) technologies to reduce greenhouse gas emissions in a large retail shopping centre located in Sydney, Australia. Large retail shopping centres take the largest share of energy consumed by all commercial buildings, and present a strong case for adoption of DER technologies to reduce energy costs and emissions. However, the complexity of optimally designing and operating DER systems has hindered their widespread adoption in practice. This paper examines and demonstrates the value of DER in reducing the carbon footprint of the shopping centre by formulating and solving a multiobjective optimisation problem using the Distributed Energy Resources Customer Adoption Model (DER-CAM) tool. An economic model of the shopping centre is developed in DER-CAM using on-site-specific demand, tariffs, and performance data for each DER technology option available. Four key optimal DER technology investment scenarios are then analysed by comparing: (1) solution trade-offs of costs and emissions, (2) the cost of reduced emissions attained in each investment scenario, and (3) investment benefits with respect to the business-as-usual scenario. The analysis shows that a moderate investment in combined cooling, heat and power (CCHP) technology alone can reduce annual energy costs by 8.5% and carbon dioxide-equivalent emissions by 29.6%. A larger investment in CCHP technology, in conjunction with on-site solar photovoltaic (PV) generation, can deliver

A pilot weight reduction program over one year significantly reduced DNA strand breaks in obese subjects

Directory of Open Access Journals (Sweden)

Karl-Heinz Wagner

2015-05-01

Conclusion: A sustainable lifestyle change under supervision including physical activity and diet quality over a period of one year was not only responsible to reduce body weight and BMI but also led to significant reduction in all parameters of the comet assay. These results underline the importance of body weight reduction and highlight the positive changes in DNA stability.

Exploring energy loss by vector flow mapping in children with ventricular septal defect: Pathophysiologic significance.

Science.gov (United States)

Honda, Takashi; Itatani, Keiichi; Takanashi, Manabu; Kitagawa, Atsushi; Ando, Hisashi; Kimura, Sumito; Oka, Norihiko; Miyaji, Kagami; Ishii, Masahiro

2017-10-01

Vector flow mapping is a novel echocardiographic flow visualization method, and it has enabled us to quantitatively evaluate the energy loss in the left ventricle (intraventricular energy loss). Although intraventricular energy loss is assumed to be a part of left ventricular workload itself, it is unclear what this parameter actually represents. The aim of the present study was to elucidate the characteristics of intraventricular energy loss. We enrolled 26 consecutive children with ventricular septal defect (VSD). On echocardiography vector flow mapping, intraventricular energy loss was measured in the apical 3-chamber view. We measured peak energy loss and averaged energy loss in the diastolic and systolic phases, and subsequently compared these parameters with catheterization parameters and serum brain natrium peptide (BNP) level. Diastolic, peak, and systolic energy loss were strongly and positively correlated with right ventricular systolic pressure (r=0.76, 0.68, and 0.56, p<0.0001, = 0.0001, and 0.0029, respectively) and right ventricular end diastolic pressure (r=0.55, 0.49, and 0.49, p=0.0038, 0.0120, and 0.0111, respectively). In addition, diastolic, peak, and systolic energy loss were significantly correlated with BNP (r=0.75, 0.69 and 0.49, p<0.0001, < 0.0001, and=0.0116, respectively). In children with VSD, elevated right ventricular pressure is one of the factors that increase energy loss in the left ventricle. The results of the present study encourage further studies in other study populations to elucidate the characteristics of intraventricular energy loss for its possible clinical application. Copyright © 2017 Elsevier B.V. All rights reserved.

Energy-loss return gate via liquid dielectric polarization.

Science.gov (United States)

Kim, Taehun; Yong, Hyungseok; Kim, Banseok; Kim, Dongseob; Choi, Dukhyun; Park, Yong Tae; Lee, Sangmin

2018-04-12

There has been much research on renewable energy-harvesting techniques. However, owing to increasing energy demands, significant energy-related issues remain to be solved. Efforts aimed at reducing the amount of energy loss in electric/electronic systems are essential for reducing energy consumption and protecting the environment. Here, we design an energy-loss return gate system that reduces energy loss from electric/electronic systems by utilizing the polarization of liquid dielectrics. The use of a liquid dielectric material in the energy-loss return gate generates electrostatic potential energy while reducing the dielectric loss of the electric/electronic system. Hence, an energy-loss return gate can make breakthrough impacts possible by amplifying energy-harvesting efficiency, lowering the power consumption of electronics, and storing the returned energy. Our study indicates the potential for enhancing energy-harvesting technologies for electric/electronics systems, while increasing the widespread development of these systems.

Geological subsurface will contribute significantly to the implementation of the energy policy towards renewables in Germany

Science.gov (United States)

Martens, Sonja; Kühn, Michael

2015-04-01

The demands to exploit the geological subsurface are increasing. In addition to the traditional production of raw materials such as natural gas and petroleum, or potable groundwater extraction the underground will most likely also be used to implement the climate and energy policy objectives in the context of the energy transition to renewables. These include the storage of energy from renewable sources (e.g. hydrogen and methane), the use of geothermal energy and possibly the long-term storage of carbon dioxide to reduce the release of greenhouse gases into the atmosphere. The presentation addresses the question which realistic contribution can be expected from the geo-resource subsurface for the energy revolution, the detachment of fossil and nuclear fuels as well as the reduction of CO2 emissions. The study of Henning and Palzer [1] that models the energy balance of the electricity and heat sector including all renewable energy converters, storage components and loads for a future German energy system shows that provision with 100% renewables is economically feasible by 2050. Based on their work, our estimates underline that already in 2015 more than 100% of the required methane storage capacities therein are available and more than 100% of the heat pump demands might be covered by shallow and deep geothermal energy production in the future. In addition we show that a newly developed energy storage system [2-3] could be applied to store 20-60% of the surplus energy from renewables expected for 2050 with integrated gas storage of methane and CO2. [1] Henning H-M, Palzer A (2014) A comprehensive model for the German electricity and heat sector in a future energy system with a dominant contribution from renewable energy technologies -- Part I: Methodology. Renewable and Sustainable Energy Reviews 30, 1003-1018. doi: 10.1016/j.rser.2013.09.012 [2] Kühn M, Nakaten N, Streibel M, Kempka T (2014) CO2 geological storage and utilization for a carbon neutral "power

The Energy Efficient Enterprise

Energy Technology Data Exchange (ETDEWEB)

Ahmad, Bashir

2010-09-15

Since rising energy costs have become a crucial factor for the economy of production processes, the optimization of energy efficiency is of essential importance for industrial enterprises. Enterprises establish energy saving programs, specific to their needs. The most important elements of these energy efficiency programs are energy savings, energy controlling, energy optimization, and energy management. This article highlights the industrial enterprise approach to establish sustainable energy management programs based on the above elements. Globally, if organizations follow this approach, they can significantly reduce the overall energy consumption and cost.

Power to change: Analysis of household participation in a renewable energy and energy efficiency programme in Central Australia

International Nuclear Information System (INIS)

Havas, Lisa; Ballweg, Julie; Penna, Chris; Race, Digby

2015-01-01

The Australian government funded a national Solar City program (2008–2013) to support communities to increase adoption of energy efficiency measures and renewable energy technology. One community was Alice Springs, a town with about 9000 households in the geographic centre of Australia. The programme offered a package of support: free energy audits, discounts for the purchase of renewable energy technology and energy efficiency measures, and ongoing information. Households that adopted solar hot water and photovoltaic systems reduced their electricity usage immediately after adoption by 10% and 34% respectively, and this was maintained in the long term. A small rebound effect of 15% was observed in the photovoltaic adopters. It was observed that, on average, households that adopted only energy efficiency measures did not have a significant reduction in their electricity usage over the long term. However, consistent with expectations, this study did show that there was a significant correlation between the number of energy efficiency measures adopted and the greatest household reduction in electricity usage. These contrary results indicate that there are additional factors involved. The connection between the effective use of measures, coincident behavioural change or increased energy awareness and greater energy reduction is discussed. - Highlights: • Households adopting solar hot water systems reduced total electricity usage by 10%. • Households adopting photovoltaic systems reduced total electricity usage by 34%. • 15% rebound effect in electricity usage by adopters of photovoltaic systems. • Excluding renewable energy no significant reduction in average electricity use.

Energy supply measures to reduce regional carbon intensity: opportunities and constraints

Energy Technology Data Exchange (ETDEWEB)

McEvoy, D.; Gibbs, D.C.; Longhurst, J.W.S. [University of Hull, Hull (United Kingdom). Dept. of Geography

1998-07-01

The perceived threat of `enhanced` global warming has become a widespread public concern since the late 1980s, with the balance of informed opinion urging world-wide collaboration on combating the causes of global warming. The increasingly globalised status of the majority of late twentieth century economies ensures that remedial action will ultimately require a degree of international cooperation. Although the formulation of environmentally friendly energy policies, including carbon reduction strategies, can be framed at international and national levels, recent trends are for CO{sub 2} reduction measures to be instigated by regional, or local, authorities. This paper focuses on the city-region of Greater Manchester, UK, and reviews both existing and potential energy supply options for reducing regional CO{sub 2} emissions, highlighting the benefits and obstacles facing carbon reduction measures implemented at a `local` scale. Mitigation action at this level is considered desirable as remedial measures have most chance of success when accompanied by the supportive involvement of local people. 73 refs.

Genetic Engineering of Energy Crops to Reduce Recalcitrance and Enhance Biomass Digestibility

Directory of Open Access Journals (Sweden)

Monika Yadav

2018-06-01

Full Text Available Bioenergy, biofuels, and a range of valuable chemicals may be extracted from the abundantly available lignocellulosic biomass. To reduce the recalcitrance imposed by the complex cell wall structure, genetic engineering has been proposed over the years as a suitable solution to modify the genes, thereby, controlling the overall phenotypic expression. The present review provides a brief description of the plant cell wall structure and its compositional array i.e., lignin, cellulose, hemicellulose, wall proteins, and pectin, along with their effect on biomass digestibility. Also, this review discusses the potential to increase biomass by gene modification. Furthermore, the review highlights the potential genes associated with the regulation of cell wall structure, which can be targeted for achieving energy crops with desired phenotypes. These genetic approaches provide a robust and assured method to bring about the desired modifications in cell wall structure, composition, and characteristics. Ultimately, these genetic modifications pave the way for achieving enhanced biomass yield and enzymatic digestibility of energy crops, which is crucial for maximizing the outcomes of energy crop breeding and biorefinery applications.

Electromagnetic therapeutic coils design to reduce energy loss

Directory of Open Access Journals (Sweden)

Syrek Przemyslaw

2016-01-01

Full Text Available The article introduces the problem of power loss reduction in applicators used in magnetotherapy. To generate magnetic field whose distribution is optimal and to reduce the power loss, the authors establish a set of parameters to evaluate the model of device. Results make it possible to infer that the real power input necessary to operate the magnetic field generator properly may vary significantly depending on construction and localization. The issues raised in this paper should be treated as a basis for further discussion on the construction of applicators used, e.g., in Transcranial Magnetic Stimulation.

Energy system analysis of CAES technologies in the Danish energy system with high penetration of fluctuating renewable energy sources

DEFF Research Database (Denmark)

Salgi, Georges Garabeth; Lund, Henrik

2006-01-01

countries. However, plans to expand wind power locally and in the neighbouring countries could restrain the export option and create transmission congestion challenges. This results in a need to increase the flexibility of the local electricity system. Compressed Air Energy Storage (CAES) has been proposed...... effect on reducing excess electricity production, the storage capacity of CAES has to be increased significantly compared to current technology. It is thus concluded that, seen from a local energy system balance perspective, CAES has little potential for reducing excess electricity production...

Determination of feasibility and advantages of using additional turbines to reduce energy consumption and CO2 emission of a distillation column

Directory of Open Access Journals (Sweden)

Svang-Ariyaskul Apichit

2014-01-01

Full Text Available Distillation is a process that consumes an extensive amount of energy and emits an enormous amount of CO2. It is attractive to reduce the energy consumption and CO2 emission for distillation. A new design of distillation is proposed by adding turbines in the vapor process streams before the condenser and after a reboiler to produce domestic electricity. As a result, this new design helps in reducing energy consumption and CO2 emission. The key variables are the distillate to feed ratio and the reflux ratio because they are the direct factors that control the vapor flowrates supplying the turbines. The distillation of an alkane mixture of C4 - C8 commonly found in a petroleum refinery was used as a test model to prove the process feasibility. The energy consumption and CO2 emission of the new process are reduced to 0.93 - 0.96 and 0.89 - 0.90 of the conventional process, respectively. This new design increases process efficiency in terms of second law efficiency by reducing the entropy generation from the conventional distillation at low distillate to feed ratios and reflux ratios. The distillation with additional turbines is promising to reduce energy consumption and CO2 emission and to increase process efficiency.

[Effect of 3-month exercise training on daily energy expenditure in formerly obese women with reduced and stable weight].

Science.gov (United States)

Buemann, B; Astrup, A V

1993-06-14

Predisposition to obesity has been suggested to be related to a low energy expenditure (EE). This condition could be counteracted by physical exercise. In the present study we wanted to elucidate if aerob training could increase sedentary 24-hour energy expenditure in formerly obese subjects. Seven reduced-obese premenopausal women were studied in a respiration chamber before and after a three month period of aerobic training. No significant effects of training were seen on daytime, sleeping or total 24-hour EE. However, the change in daytime EE was positively correlated to the change in VO2max. Sleeping and 24-hour respiratory quotients were slightly increased after the training period. In order to reveal a possible role of the sympathetic nervous system in the observed effect of training, additional experiments were performed with beta blockade. However, no interactions between training and beta blockade were found.

The genetic basis of energy conservation in the sulfate-reducing bacterium Desulfovibrio alaskensis G20

Directory of Open Access Journals (Sweden)

Morgan N Price

2014-10-01

Full Text Available Sulfate-reducing bacteria play major roles in the global carbon and sulfur cycles, but it remains unclear how reducing sulfate yields energy. To determine the genetic basis of energy conservation, we measured the fitness of thousands of pooled mutants of Desulfovibrio alaskensis G20 during growth in 12 different combinations of electron donors and acceptors. We show that ion pumping by the ferredoxin:NADH oxidoreductase Rnf is required whenever substrate-level phosphorylation is not possible. The uncharacterized complex Hdr/flox-1 (Dde_1207:13 is sometimes important alongside Rnf and may perform an electron bifurcation to generate more reduced ferredoxin from NADH to allow further ion pumping. Similarly, during the oxidation of malate or fumarate, the electron-bifurcating transhydrogenase NfnAB-2 (Dde_1250:1 is important and may generate reduced ferredoxin to allow additional ion pumping by Rnf. During formate oxidation, the periplasmic [NiFeSe] hydrogenase HysAB is required, which suggests that hydrogen forms in the periplasm, diffuses to the cytoplasm, and is used to reduce ferredoxin, thus providing a substrate for Rnf. During hydrogen utilization, the transmembrane electron transport complex Tmc is important and may move electrons from the periplasm into the cytoplasmic sulfite reduction pathway. Finally, mutants of many other putative electron carriers have no clear phenotype, which suggests that they are not important under our growth conditions, although we cannot rule out genetic redundancy.

Sound stabilizes locomotor-respiratory coupling and reduces energy cost.

Directory of Open Access Journals (Sweden)

Charles P Hoffmann

Full Text Available A natural synchronization between locomotor and respiratory systems is known to exist for various species and various forms of locomotion. This Locomotor-Respiratory Coupling (LRC is fundamental for the energy transfer between the two subsystems during long duration exercise and originates from mechanical and neurological interactions. Different methodologies have been used to compute LRC, giving rise to various and often diverging results in terms of synchronization, (de-stabilization via information, and associated energy cost. In this article, the theory of nonlinear-coupled oscillators was adopted to characterize LRC, through the model of the sine circle map, and tested it in the context of cycling. Our specific focus was the sound-induced stabilization of LRC and its associated change in energy consumption. In our experimental study, participants were instructed during a cycling exercise to synchronize either their respiration or their pedaling rate with an external auditory stimulus whose rhythm corresponded to their individual preferential breathing or cycling frequencies. Results showed a significant reduction in energy expenditure with auditory stimulation, accompanied by a stabilization of LRC. The sound-induced effect was asymmetrical, with a better stabilizing influence of the metronome on the locomotor system than on the respiratory system. A modification of the respiratory frequency was indeed observed when participants cycled in synchrony with the tone, leading to a transition toward more stable frequency ratios as predicted by the sine circle map. In addition to the classical mechanical and neurological origins of LRC, here we demonstrated using the sine circle map model that information plays an important modulatory role of the synchronization, and has global energetic consequences.

Green roofs: roof system reducing heating and cooling costs

Directory of Open Access Journals (Sweden)

Konasova, Sarka

2016-06-01

Full Text Available Green roofs are among the passive building systems that contribute to the thermal stability of the rooms under the roof in both summer and winter. Green roofs can provide a significant contribution to the thermal balance of the protected space. Over the past ten years, many studies have been carried out to investigate the energy benefits of green roofs in terms of the energy performance of buildings. These studies show that the installation of vegetated cover can achieve energy savings for both winter heating and summer cooling. The green roof, as a thermal insulation, reduces the amount of building operating energy costs and reduces heat losses. This article summarizes current literature and points to situations in which green roofs can play an important role in saving energy for heating and cooling due to improved thermal insulating function of the roof, in case of extensive vegetation coverage without significant overloading of the roof structure and associated over-dimensioning. It is important to note that these energy savings always depend on the particular climate, the type of building and the availability and the type of roof structure.

The challenge of reducing energy consumption of the Top-1000 largest industrial enterprises in China

International Nuclear Information System (INIS)

Price, Lynn; Wang Xuejun; Yun Jiang

2010-01-01

In 2005, the Chinese government announced an ambitious goal of reducing energy consumption per unit of gross domestic product (GDP) by 20% between 2005 and 2010. One of the key initiatives for realizing this goal is the Top-1000 Energy-Consuming Enterprises program. The energy consumption of these 1000 enterprises accounted for 33% of national and 47% of industrial energy usage in 2004. Under the Top-1000 program, 2010 energy consumption targets were determined for each enterprise. The objective of this article is to evaluate the program design and initial results, given limited information and data, to understand the possible implications of its success in terms of energy and carbon dioxide emission reductions and to recommend future program modifications based on international experience with similar target-setting agreement programs. Even though the Top-1000 program was designed and implemented rapidly, it appears that - depending upon the GDP growth rate - it could contribute to somewhere between approximately 10% and 25% of the savings required to support China's efforts to meet a 20% reduction in energy use per unit of GDP by 2010.

Energy-efficient induction motors designing with application of a modified criterion of reduced costs

Directory of Open Access Journals (Sweden)

V.S. Petrushin

2014-03-01

Full Text Available The paper introduces a modified criterion of reduced costs that employs coefficients of operation significance and priority of ohmic loss accounting to allow matching maximum efficiency with minimum reduced costs. Impact of the inflation factor on the criterion of reduced costs is analyzed.

Technical assessment of the significance of Wigner energy for disposal of graphite wastes from the Windscale Piles

International Nuclear Information System (INIS)

Guppy, R.M.; Wisbey, S.J.; McCarthy, J.

2001-01-01

Plans to dismantle the core of the Windscale Pile 1 reactor, and to package the waste for interim storage and eventual disposal, are well advanced. UK Nirex Limited, currently responsible for identifying and developing a site primarily for disposal of the wide range of intermediate level wastes, is addressing the suitability of the waste from Windscale Pile 1, for transport to, and disposal at, a deep waste repository. To support the decommissioning of Windscale Pile 1, information on the condition of the graphite has been sought. Despite the fire in 1957, recent sampling of regions of the core has shown that much of the graphite still contains significant residual Wigner energy. Unless it can be shown that Wigner energy will not be released at a significant rate during operations such as waste packaging or handling of the package, or after disposal, future safety cases may be undermined. A model for the release of Wigner energy has been developed, which describes the stored energy as a set of defects with different activation energies. Initial values of stored energy are attributed to each member of the set, and the energy is released using first order decay processes. By appropriate selection of the range of activation energies and stored energies attributable to each population of defects, experimentally determined releases of stored energy as a function of temperature can be reproduced by the model. Within the disposal environment, the packages will be subject to modest heating from external sources, including the host rocks, radioactive decay, corrosion processes and heat from curing of backfill materials in the disposal vaults. The Wigner energy release model has been used in combination with finite element thermal modelling to assess the temperature evolution of stacks of waste packages located within hypothetical disposal vaults. It has also been used to assess the response of individual waste packages exposed to fires. This paper provides a summary of the

Energy and exergy analysis of electricity generation from natural gas pressure reducing stations

International Nuclear Information System (INIS)

Neseli, Mehmet Alparslan; Ozgener, Onder; Ozgener, Leyla

2015-01-01

Highlights: • Forecasting the recoverable energy from natural gas pressure reduction stations. • Electricity generation through pressure reduction stations via turboexpanders. • A thermodynamics analysis of PRS. - Abstract: Electricity generation or power recovery through pressure reduction stations (PRS) for general use has not been realized in Izmir. The main objective of the present study was to do a case study for calculating electricity to be recovered in one natural gas pressure reduction stations in Izmir. It is the first forecasting study to obtain energy from natural gas pressure-reducing stations in Izmir. Energy can be obtained from natural gas PRS with turbo-expanders instead of using throttle valves or regulators from the PRS. The exergy performance of PRS with TE is evaluated in this study. Exergetic efficiencies of the system and components are determined to assess their individual performances. Based upon pressure change and volumetric flow rate, it can be obtained by recovering average estimated installed capacity and annual energy 494.24 kW, 4113.03 MW h, respectively. In terms of estimated installed capacity power and annual energy, the highest level is 764.88 kW, approximately 6365.34 MW h, in Aliaga PRS. Also it can be seen that CO 2 emission factor average value is 295.45 kg/MW h

Potential energy efficiency and conservation, economic, and environmental benefits from the implementation of superconducting magnetic energy storage

International Nuclear Information System (INIS)

Baumann, P.D.

1992-01-01

This paper reports on Superconducting Magnetic Energy Storage (SMES) which is a recent technology that has the capability to significantly improve electrical system operations within electric utility systems. The technology has already been demonstrated by Bonneville Power Administration in a 30-MJ SMES test demonstration unit. Savings in utility operations from improved system efficiency, increased reliability, and reduced maintenance requirements contribute to the economic justification of SMES. Beyond these benefits, there are additional benefits which in the long run may equal or outweigh the electrical operational benefits. These benefits are the energy conservation and environmental benefits. The technology has the capability of reducing fuel consumption which can in turn reduce emissions. In a regional setting it can shift emissions both in volumes and in physical. With its capability to strategically shift generation and significantly affect emissions and air quality it can stretch clean energy generation options, thus SMES can be seen as an energy and environmental management technology and tool

Energy Cost Minimization in Heterogeneous Cellular Networks with Hybrid Energy Supplies

Directory of Open Access Journals (Sweden)

Bang Wang

2016-01-01

Full Text Available The ever increasing data demand has led to the significant increase of energy consumption in cellular mobile networks. Recent advancements in heterogeneous cellular networks and green energy supplied base stations provide promising solutions for cellular communications industry. In this article, we first review the motivations and challenges as well as approaches to address the energy cost minimization problem for such green heterogeneous networks. Owing to the diversities of mobile traffic and renewable energy, the energy cost minimization problem involves both temporal and spatial optimization of resource allocation. We next present a new solution to illustrate how to combine the optimization of the temporal green energy allocation and spatial mobile traffic distribution. The whole optimization problem is decomposed into four subproblems, and correspondingly our proposed solution is divided into four parts: energy consumption estimation, green energy allocation, user association, and green energy reallocation. Simulation results demonstrate that our proposed algorithm can significantly reduce the total energy cost.

Finding of no significant impact for the State Energy Conservation Program

International Nuclear Information System (INIS)

1996-01-01

The Department of Energy (DOE) has prepared a Programmatic Environmental Assessment (PEA), DOE/EA 1068, to assess the environmental impacts associated with the State Energy Conservation Program (SECP). DOE previously funded SECP projects under the Energy Policy and Conservation Act of 1975 (EPCA). The State Energy Efficiency Programs Improvements Act of 1990 (SEEPIA) and the Energy Policy Act of 1992 (EPACT) amended EPCA to broaden the range of state initiatives qualifying for Federal assistance under the SECP. The PEA presents a general analysis of the potential environmental effects associated with broad types of projects that can be funded under the SECP. It does not analyze specific environmental effects or alternatives associated with individual energy conservation, energy efficiency, and renewable energy projects. Individual actions are to be evaluated in detail on a project-by-project basis to determine whether their impacts fall within the bounding analysis of the impacts analyzed in the SECP PEA

Reduced energy consumption by massive thermoelectric waste heat recovery in light duty trucks

Science.gov (United States)

Magnetto, D.; Vidiella, G.

2012-06-01

The main objective of the EC funded HEATRECAR project is to reduce the energy consumption and curb CO2 emissions of vehicles by massively harvesting electrical energy from the exhaust system and re-use this energy to supply electrical components within the vehicle or to feed the power train of hybrid electrical vehicles. HEATRECAR is targeting light duty trucks and focuses on the development and the optimization of a Thermo Electric Generator (TEG) including heat exchanger, thermoelectric modules and DC/DC converter. The main objective of the project is to design, optimize and produce a prototype system to be tested on a 2.3l diesel truck. The base case is a Thermo Electric Generator (TEG) producing 1 KWel at 130 km/h. We present the system design and estimated output power from benchmark Bi2Te3 modules. We discuss key drivers for the optimization of the thermal-to-electric efficiency, such as materials, thermo-mechanical aspects and integration.

Reduced bone mineral density is not associated with significantly reduced bone quality in men and women practicing long-term calorie restriction with adequate nutrition.

Science.gov (United States)

Villareal, Dennis T; Kotyk, John J; Armamento-Villareal, Reina C; Kenguva, Venkata; Seaman, Pamela; Shahar, Allon; Wald, Michael J; Kleerekoper, Michael; Fontana, Luigi

2011-02-01

Calorie restriction (CR) reduces bone quantity but not bone quality in rodents. Nothing is known regarding the long-term effects of CR with adequate intake of vitamin and minerals on bone quantity and quality in middle-aged lean individuals. In this study, we evaluated body composition, bone mineral density (BMD), and serum markers of bone turnover and inflammation in 32 volunteers who had been eating a CR diet (approximately 35% less calories than controls) for an average of 6.8 ± 5.2 years (mean age 52.7 ± 10.3 years) and 32 age- and sex-matched sedentary controls eating Western diets (WD). In a subgroup of 10 CR and 10 WD volunteers, we also measured trabecular bone (TB) microarchitecture of the distal radius using high-resolution magnetic resonance imaging. We found that the CR volunteers had significantly lower body mass index than the WD volunteers (18.9 ± 1.2 vs. 26.5 ± 2.2 kg m(-2) ; P = 0.0001). BMD of the lumbar spine (0.870 ± 0.11 vs. 1.138 ± 0.12 g cm(-2) , P = 0.0001) and hip (0.806 ± 0.12 vs. 1.047 ± 0.12 g cm(-2) , P = 0.0001) was also lower in the CR than in the WD group. Serum C-terminal telopeptide and bone-specific alkaline phosphatase concentration were similar between groups, while serum C-reactive protein (0.19 ± 0.26 vs. 1.46 ± 1.56 mg L(-1) , P = 0.0001) was lower in the CR group. Trabecular bone microarchitecture parameters such as the erosion index (0.916 ± 0.087 vs. 0.877 ± 0.088; P = 0.739) and surface-to-curve ratio (10.3 ± 1.4 vs. 12.1 ± 2.1, P = 0.440) were not significantly different between groups. These findings suggest that markedly reduced BMD is not associated with significantly reduced bone quality in middle-aged men and women practicing long-term calorie restriction with adequate nutrition.

Informing Intervention Strategies to Reduce Energy Drink Consumption in Young People: Findings From Qualitative Research.

Science.gov (United States)

Francis, Jacinta; Martin, Karen; Costa, Beth; Christian, Hayley; Kaur, Simmi; Harray, Amelia; Barblett, Ann; Oddy, Wendy Hazel; Ambrosini, Gina; Allen, Karina; Trapp, Gina

2017-10-01

To determine young people's knowledge of energy drinks (EDs), factors influencing ED consumption, and intervention strategies to decrease ED consumption in young people. Eight group interviews with young people (aged 12-25 years). Community groups and secondary schools in Perth, Western Australia. Forty-one young people, 41% of whom were male and 73% of whom consumed EDs. Factors influencing ED consumption and intervention strategies informed by young people to reduce ED consumption. Two researchers conducted a qualitative content analysis on the data using NVivo software. Facilitators of ED consumption included enhanced energy, pleasant taste, low cost, peer pressure, easy availability, and ED promotions. Barriers included negative health effects, unpleasant taste, high cost, and parents' disapproval. Strategies to reduce ED consumption included ED restrictions, changing ED packaging, increasing ED prices, reducing visibility in retail outlets, and research and education. Because many countries allow the sale of EDs to people aged consumption. In addition to more research and education, these strategies included policy changes targeting ED sales, packaging, price, and visibility. Future research might examine the feasibility of implementing such interventions. Copyright © 2017 Society for Nutrition Education and Behavior. Published by Elsevier Inc. All rights reserved.

Food transport refrigeration - Approaches to reduce energy consumption and environmental impacts of road transport

International Nuclear Information System (INIS)

Tassou, S.A.; De-Lille, G.; Ge, Y.T.

2009-01-01

Food transport refrigeration is a critical link in the food chain not only in terms of maintaining the temperature integrity of the transported products but also its impact on energy consumption and CO 2 emissions. This paper provides a review of (a) current approaches in road food transport refrigeration, (b) estimates of their environmental impacts, and (c) research on the development and application of alternative technologies to vapour compression refrigeration systems that have the potential to reduce the overall energy consumption and environmental impacts. The review and analysis indicate that greenhouse gas emissions from conventional diesel engine driven vapour compression refrigeration systems commonly employed in food transport refrigeration can be as high as 40% of the greenhouse gas emissions from the vehicle's engine. For articulated vehicles over 33 ton, which are responsible for over 80% of refrigerated food transportation in the UK, the reject heat available form the engine is sufficient to drive sorption refrigeration systems and satisfy most of the refrigeration requirements of the vehicle. Other promising technologies that can lead to a reduction in CO 2 emissions are air cycle refrigeration and hybrid systems in which conventional refrigeration technologies are integrated with thermal energy storage. For these systems, however, to effectively compete with diesel driven vapour compression systems, further research and development work is needed to improve their efficiency and reduce their weight

Energy Information Augmented Community-Based Energy Reduction

Directory of Open Access Journals (Sweden)

Mark Rembert

2012-06-01

Full Text Available More than one-half of all U.S. states have instituted energy efficiency mandates requiring utilities to reduce energy use. To achieve these goals, utilities have been permitted rate structures to help them incentivize energy reduction projects. This strategy is proving to be only modestly successful in stemming energy consumption growth. By the same token, community energy reduction programs have achieved moderate to very significant energy reduction. The research described here offers an important tool to strengthen the community energy reduction efforts—by providing such efforts energy information tailored to the energy use patterns of each building occupant. The information provided most importantly helps each individual energy customer understand their potential for energy savings and what reduction measures are most important to them. This information can be leveraged by the leading community organization to prompt greater action in its community. A number of case studies of this model are shown. Early results are promising.

The significance of renewable energy use for economic output and environmental protection: evidence from the Next 11 developing economies.

Science.gov (United States)

Paramati, Sudharshan Reddy; Sinha, Avik; Dogan, Eyup

2017-05-01

Increasing economic activities in developing economies raise demand for energy mainly sourced from conventional sources. The consumption of more conventional energy will have a significant negative impact on the environment. Therefore, attention of policy makers has recently shifted towards the promotion of renewable energy generation and uses across economic activities to ensure low carbon economy. Given the recent scenario, in this paper, we aim to examine the role of renewable energy consumption on the economic output and CO 2 emissions of the next fastest developing economies of the world. The study employs several robust panel econometric models by using annual data from 1990 to 2012. Empirical findings confirm the significant long-run association among the variables. Similarly, results show that renewable energy consumption positively contributes to economic output and has an adverse effect on CO 2 emissions. Given our findings, we suggest policy makers of those economies to initiate further effective policies to promote more renewable energy generation and uses across economic activities to ensure sustainable economic development.

Fossil energy use and the environment

International Nuclear Information System (INIS)

Sage, P.W.

1994-01-01

Energy demand projections indicate that fossil energy will provide some ninety per cent of global primary energy demand for the foreseeable future. This paper considers the principal environmental impacts associated with fossil energy use and describes approaches to minimise them. Technologies are now available to reduce significantly pollutant emissions from fossil fuel use. Emerging technologies offer higher conversion efficiencies to reduce still further specific emissions per unit of energy output. It is essential, particularly in those areas of rapid growth in energy use, that best practice and technology are deployed. Technology transfer and training will help to achieve this and enable fossil energy use to be fully compatible with increasingly stringent environmental requirements. (author) 4 figs., 12 refs

Energy drink consumption is associated with reduced sleep quality among college students: a cross-sectional study.

Science.gov (United States)

Faris, Mo'ez Al-Islam E; Jahrami, Haitham; Al-Hilali, Marwa M; Chehyber, Noor J; Ali, Sara O; Shahda, Sara D; Obaid, Reyad S

2017-07-01

Intake of caffeinated energy drinks has significantly increased, specifically among young adults and adolescents. College students are prone to developing unhealthy eating habits and dependence on stimulants, which puts them at a greater risk of sleep problems. This study aims to investigate the prevalence of caffeinated energy drink consumption and its association with sleep quality in college students. A sample of 919 randomly selected adults (237 males and 682 females) from various colleges at the University of Sharjah/United Arab Emirates participated in this cross-sectional study. Data were collected using an online validated questionnaire. The current study revealed that 376 students (41%) were consuming energy drinks on a regular basis. Approximately half of the students had normal sleep patterns; the other half had sleep problems (anxiety and intermittent sleep). Results of the present study revealed a significant (r = -0.10, P consumption of energy drinks and sleep quality and patterns. Moderate consumption of energy drinks was reported among college students. Consumption of energy drinks was significantly associated with changes in sleep quality and patterns of students. © 2016 Dietitians Association of Australia.

Online-based energy auditing and incentive mechanisms to reduce domestic energy consumption

OpenAIRE

Lossin, Felix; Staake, Thorsten; Fleisch, Elgar

2014-01-01

Domestic energy consumption accounts for about 20-30% of total energy use in western countries [1], [2]. On the level of single households, however, energy consumption tends to vary greatly. This is particularly due to differences regarding behavior and decisions made by individuals. For example, heating and ventilation behavior, the intensity of the use of electrical appliances and hot water, as well as home insulation and weatherization provisions affect total energy consumption. Therefore,...

Energy comes home

International Nuclear Information System (INIS)

Aune, Margrethe

2007-01-01

The growth in private energy consumption is an increasing problem in western countries. From an environmental point of view, this consumption has to be reduced. On the basis of two Norwegian case studies, this article discusses private energy consumption and possibilities for reduction, with a special focus on the home. It argues against a rational economic view of the consumer and emphasizes the significance of a more subtle understanding of private energy use. The article approaches the challenges of reducing private energy consumption by analysing the domestication of the home and discusses everyday life activities as well as the phenomenon of rebuilding and redecorating. By using the concept of domestication, the article challenges the linear understanding of technological as well as behavioural change. Private energy consumption is part of a complex network and it is necessary to understand this network in order to achieve a more permanent reduction

Distributed Wireless Multi-Sensor Technologies, A Novel Approach to Reduce Motor Energy Usage

Energy Technology Data Exchange (ETDEWEB)

Daniel Sexton

2008-03-28

This report is the final report for the General Electric Distributed Wireless Multi-Sensor Technologies project. The report covers the research activities and benefits surrounding wireless technology used for industrial sensing applications. The main goal of this project was to develop wireless sensor technology that would be commercialized and adopted by industry for a various set of applications. Many of these applications will yield significant energy savings. One application where there was significant information to estimate a potential energy savings was focused on equipment condition monitoring and in particular electric motor monitoring. The results of the testing of the technology developed are described in this report along with the commercialization activities and various new applications and benefits realized.

Eating 'attentively' reduces later energy consumption in overweight and obese females.

Science.gov (United States)

Robinson, Eric; Kersbergen, Inge; Higgs, Suzanne

2014-08-28

Attentional and memory processes underpin appetite control, but whether encouraging overweight individuals to eat more 'attentively' can promote reductions in energy consumption is unclear. In the present study with a between-subjects design, a total of forty-eight overweight and obese females consumed a fixed lunchtime meal. Their ad libitum energy intake of high-energy snack food was observed during a second laboratory session that occurred later that day. In the focused-attention condition, participants ate their lunch while listening to audio instructions that encouraged them to pay attention to the food being eaten. In a control condition, participants ate while listening to an audio book with a neutral (non-food-related) content. To test whether focused attention influenced food intake via enhancing the memory of the earlier consumed meal, we measured the participants' memory of their lunchtime meal. Ad libitum snack intake was approximately 30 % lower for participants in the focused-attention condition than for those in the control condition, and this difference was statistically significant. There was limited evidence that attention decreased later food intake by enhancing memory representation of the earlier consumed meal. Eating attentively can lead to a substantial decrease in later energy intake in overweight and obese individuals. Behavioural strategies that encourage a more 'attentive' way of eating could promote sustained reductions in energy intake and weight loss.

Dual-energy CT and ceramic or titanium prostheses material reduce CT artifacts and provide superior image quality of total knee arthroplasty.

Science.gov (United States)

Kasparek, Maximilian F; Töpker, Michael; Lazar, Mathias; Weber, Michael; Kasparek, Michael; Mang, Thomas; Apfaltrer, Paul; Kubista, Bernd; Windhager, Reinhard; Ringl, Helmut

2018-06-07

To evaluate the influence of different scan parameters for single-energy CT and dual-energy CT, as well as the impact of different material used in a TKA prosthesis on image quality and the extent of metal artifacts. Eight pairs of TKA prostheses from different vendors were examined in a phantom set-up. Each pair consisted of a conventional CoCr prosthesis and the corresponding anti-allergic prosthesis (full titanium, ceramic, or ceramic-coated) from the same vendor. Nine different (seven dual-energy CT and two single-energy CT) scan protocols with different characteristics were used to determine the most suitable CT protocol for TKA imaging. Quantitative image analysis included assessment of blooming artifacts (metal implants appear thicker on CT than they are, given as virtual growth in mm in this paper) and streak artifacts (thick dark lines around metal). Qualitative image analysis was used to investigate the bone-prosthesis interface. The full titanium prosthesis and full ceramic knee showed significantly fewer blooming artifacts compared to the standard CoCr prosthesis (mean virtual growth 0.6-2.2 mm compared to 2.9-4.6 mm, p energy CT protocols showed less blooming (range 3.3-3.8 mm) compared to single-energy protocols (4.6-5.5 mm). The full titanium and full ceramic prostheses showed significantly fewer streak artifacts (mean standard deviation 77-86 Hounsfield unit (HU)) compared to the standard CoCr prosthesis (277-334 HU, p energy CT protocols had fewer metal streak artifacts (215-296 HU compared to single-energy CT protocols (392-497 HU)). Full titanium and ceramic prostheses were ranked superior with regard to the image quality at the bone/prosthesis interface compared to a standard CoCr prosthesis, and all dual-energy CT protocols were ranked better than single-energy protocols. Dual-energy CT and ceramic or titanium prostheses reduce CT artifacts and provide superior image quality of total knee arthroplasty at the bone/prosthesis interface

Mindfulness significantly reduces self-reported levels of anxiety and depression

DEFF Research Database (Denmark)

Würtzen, Hanne; Dalton, Susanne Oksbjerg; Elsass, Peter

2013-01-01

INTRODUCTION: As the incidence of and survival from breast cancer continue to raise, interventions to reduce anxiety and depression before, during and after treatment are needed. Previous studies have reported positive effects of a structured 8-week group mindfulness-based stress reduction program...

Building Commissioning: A Golden Opportunity for Reducing Energy Costs and Greenhouse-gas Emissions

Energy Technology Data Exchange (ETDEWEB)

Mills, Evan

2009-07-16

data are available revealed over 10,000 energy-related problems, resulting in 16% median whole-building energy savings in existing buildings and 13% in new construction, with payback time of 1.1 years and 4.2 years, respectively. In terms of other cost-benefit indicators, median benefit-cost ratios of 4.5 and 1.1, and cash-on-cash returns of 91% and 23% were attained for existing and new buildings, respectively. High-tech buildings were particularly cost-effective, and saved higher amounts of energy due to their energy-intensiveness. Projects with a comprehensive approach to commissioning attained nearly twice the overall median level of savings and five-times the savings of the least-thorough projects. It is noteworthy that virtually all existing building projects were cost-effective by each metric (0.4 years for the upper quartile and 2.4 years for the lower quartile), as were the majority of new-construction projects (1.5 years and 10.8 years, respectively). We also found high cost-effectiveness for each specific measure for which we have data. Contrary to a common perception, cost-effectiveness is often achieved even in smaller buildings. Thanks to energy savings valued more than the cost of the commissioning process, associated reductions in greenhouse gas emissions come at 'negative' cost. In fact, the median cost of conserved carbon is negative - -$110 per tonne for existing buildings and -$25/tonne for new construction - as compared with market prices for carbon trading and offsets in the +$10 to +$30/tonne range. Further enhancing the value of commissioning, its non-energy benefits surpass those of most other energy-management practices. Significant first-cost savings (e.g., through right-sizing of heating and cooling equipment) routinely offset at least a portion of commissioning costs - fully in some cases. When accounting for these benefits, the net median commissioning project cost was reduced by 49% on average, while in many cases they exceeded

Regional growth and energy supply: Is there an energy security issue?

Energy Technology Data Exchange (ETDEWEB)

Roop, J.M.; Freund, K.A.; Godoy-Kain, P.; Gu, A.Y.; Johnson, A.K.; Paananen, O.H.; Woodruff, M.G.

1996-12-01

This study examines how the growth of the developing world might affect energy markets in the future. Based on recent growth trends, world energy demand could reasonably be expected to grow from about 350 Exajoules (EJ: 1.0E18=0.95 Quad) to nearly 1025 EJ by the year 2020, nearly 3x current consumption estimates. Introduction of more energy-efficient technologies could reduce this growth by about 17% to 830 EJ. But one cannot rely exclusively on current trends to forecast future energy demand. The growth of the developing world will interact with supply to affect prices, which in turn will mitigate the growth of demand, and growth rates of energy use will be much more modes. Under the Business as Usual scenario, energy demand will grow to 835 EJ by 2020, and this could be reduced a further 15% to 714 EJ through the adoption of more energy efficient technologies. Fuel prices based on model results are analyzed. Energy security implications of rapid growth in the developing world are considered and found to be of likely little significance.

Reduced content of chloroatranol and atranol in oak moss absolute significantly reduces the elicitation potential of this fragrance material.

Science.gov (United States)

Andersen, Flemming; Andersen, Kirsten H; Bernois, Armand; Brault, Christophe; Bruze, Magnus; Eudes, Hervé; Gadras, Catherine; Signoret, Anne-Cécile J; Mose, Kristian F; Müller, Boris P; Toulemonde, Bernard; Andersen, Klaus Ejner

2015-02-01

Oak moss absolute, an extract from the lichen Evernia prunastri, is a valued perfume ingredient but contains extreme allergens. To compare the elicitation properties of two preparations of oak moss absolute: 'classic oak moss', the historically used preparation, and 'new oak moss', with reduced contents of the major allergens atranol and chloroatranol. The two preparations were compared in randomized double-blinded repeated open application tests and serial dilution patch tests in 30 oak moss-sensitive volunteers and 30 non-allergic control subjects. In both test models, new oak moss elicited significantly less allergic contact dermatitis in oak moss-sensitive subjects than classic oak moss. The control subjects did not react to either of the preparations. New oak moss is still a fragrance allergen, but elicits less allergic contact dermatitis in previously oak moss-sensitized individuals, suggesting that new oak moss is less allergenic to non-sensitized individuals. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Reducing Mg acceptor activation-energy in Al(0.83)Ga(0.17)N disorder alloy substituted by nanoscale (AlN)₅/(GaN)₁ superlattice using Mg(Ga) δ-doping: Mg local-structure effect.

Science.gov (United States)

Zhong, Hong-xia; Shi, Jun-jie; Zhang, Min; Jiang, Xin-he; Huang, Pu; Ding, Yi-min

2014-10-23

Improving p-type doping efficiency in Al-rich AlGaN alloys is a worldwide problem for the realization of AlGaN-based deep ultraviolet optoelectronic devices. In order to solve this problem, we calculate Mg acceptor activation energy and investigate its relationship with Mg local structure in nanoscale (AlN)5/(GaN)1 superlattice (SL), a substitution for Al(0.83)Ga(0.17)N disorder alloy, using first-principles calculations. A universal picture to reduce acceptor activation energy in wide-gap semiconductors is given for the first time. By reducing the volume of the acceptor local structure slightly, its activation energy can be decreased remarkably. Our results show that Mg acceptor activation energy can be reduced significantly from 0.44 eV in Al(0.83)Ga(0.17)N disorder alloy to 0.26 eV, very close to the Mg acceptor activation energy in GaN, and a high hole concentration in the order of 10(19) cm(-3) can be obtained in (AlN)5/(GaN)1 SL by Mg(Ga) δ-doping owing to GaN-monolayer modulation. We thus open up a new way to reduce Mg acceptor activation energy and increase hole concentration in Al-rich AlGaN.

Reducing Mg Acceptor Activation-Energy in Al0.83Ga0.17N Disorder Alloy Substituted by Nanoscale (AlN)5/(GaN)1 Superlattice Using MgGa δ-Doping: Mg Local-Structure Effect

Science.gov (United States)

Zhong, Hong-Xia; Shi, Jun-Jie; Zhang, Min; Jiang, Xin-He; Huang, Pu; Ding, Yi-Min

2014-10-01

Improving p-type doping efficiency in Al-rich AlGaN alloys is a worldwide problem for the realization of AlGaN-based deep ultraviolet optoelectronic devices. In order to solve this problem, we calculate Mg acceptor activation energy and investigate its relationship with Mg local structure in nanoscale (AlN)5/(GaN)1 superlattice (SL), a substitution for Al0.83Ga0.17N disorder alloy, using first-principles calculations. A universal picture to reduce acceptor activation energy in wide-gap semiconductors is given for the first time. By reducing the volume of the acceptor local structure slightly, its activation energy can be decreased remarkably. Our results show that Mg acceptor activation energy can be reduced significantly from 0.44 eV in Al0.83Ga0.17N disorder alloy to 0.26 eV, very close to the Mg acceptor activation energy in GaN, and a high hole concentration in the order of 1019 cm-3 can be obtained in (AlN)5/(GaN)1 SL by MgGa δ-doping owing to GaN-monolayer modulation. We thus open up a new way to reduce Mg acceptor activation energy and increase hole concentration in Al-rich AlGaN.

Energy management: a program of energy conservation for the community college facility. [Handbook

Energy Technology Data Exchange (ETDEWEB)

Various Authors

1978-01-01

This handbook developes helps for assessing and improving the energy efficiency of the community-college facility. The TEEM approach (Total Educational Energy Management) is a labor-intensive approach which requires the commitment and participation of all segments of the college community. The TEEM program presented here defines a series of tasks selected, ordered, and implemented in such a way as to achieve two basic objectives: (1) reducing campus energy requirements, and (2) meeting those reduced energy requirements more efficiently without adversely affecting the quality of educational programs. This guide to large-scale energy conservation on college campuses includes step-by-step procedures for establishing a program task force, defining specific tasks, and assigning responsibilities. Action plans are developed, energy consumption monitored, goals set, and conservation measures implemented. A series of appendices provides more detailed information, charts, and worksheets related to all aspects of energy use. The TEEM program provides the basic structure for achieving a significant reduction in campus energy costs.

Reducing Electrical Consumption in the Forest Products Industry Using Lean Thinking

Directory of Open Access Journals (Sweden)

Scott William Lyon

2014-01-01

Full Text Available The forest products industry has an opportunity to reduce energy costs using energy management practices, thereby boosting its global competitiveness. Increasing manufacturing costs have contributed significantly to the decline of the forest products manufacturing industries in the U.S.; these increasing costs limit manufacturers’ abilities to compete with their global competitors. U.S. companies are continually improving their products, processes, finances, and business practices to better compete with global marketplaces; however, they may not be seizing all of the opportunities available through more efficient energy consumption practices. By eliminating non-valued added activities, lean thinking is an example of one tool that may improve performance and reduce costs. A case study was conducted at a cabinet manufacturer in Virginia to examine the impact of lean thinking on the consumption of electricity in the manufacturing process. An energy management system was used to provide rapid feedback on electrical energy consumption for production operations. Significant changes were observed after implementing energy reduction practices identified by lean thinking tools.

A decision support model for reducing electric energy consumption in elementary school facilities

International Nuclear Information System (INIS)

Hong, Taehoon; Koo, Choongwan; Jeong, Kwangbok

2012-01-01

Highlights: ► Decision support model is developed to reduce CO 2 emission in elementary schools. ► The model can select the school to be the most effective in energy savings. ► Decision tree improved the prediction accuracy by 1.83–3.88%. ► Using the model, decision-maker can save the electric-energy consumption by 16.58%. ► The model can make the educational-facility improvement program more effective. -- Abstract: The South Korean government has been actively promoting an educational-facility improvement program as part of its energy-saving efforts. This research seeks to develop a decision support model for selecting the facility expected to be effective in generating energy savings and making the facility improvement program more effective. In this research, project characteristics and electric-energy consumption data for the year 2009 were collected from 6282 elementary schools located in seven metropolitan cities in South Korea. In this research, the following were carried out: (i) a group of educational facilities was established based on electric-energy consumption, using a decision tree; (ii) a number of similar projects were retrieved from the same group of facilities, using case-based reasoning; and (iii) the accuracy of prediction was improved, using the combination of genetic algorithms, the artificial neural network, and multiple regression analysis. The results of this research can be useful for the following purposes: (i) preliminary research on the systematic and continuous management of educational facilities’ electric-energy consumption; (ii) basic research on electric-energy consumption prediction based on the project characteristics; and (iii) practical research for selecting an optimum facility that can more effectively apply an educational-facility improvement program as a decision support model.

An attempt to reduce radioactivity for energy-dispersive x-ray analysis

International Nuclear Information System (INIS)

Hamada, S.

1992-01-01

The object of this work is to develop a specimen preparation technique which reduces the intensity of radioactivity of a neutron-irradiated materials for microchemical analysis by analytical electron microscope (AEM) with energy dispersive X-ray spectroscopy (EDXS). A composite specimen preparation technique for the AEM was developed using unirradiated materials. The technique reduced the mass of material from a dummy irradiated specimen by more than a factor of 100. A 1-mm diam. disk was punched from a dummy irradiated 3-mm diam. transmission electron microscope (TEM) disk. The 1-mm disk was then pressed into a hole previously punched at the center of a second 3 mm diam. disk creating a composite disk. The composite disk was electropolished using a twin jet Tenupol until the thickness of the center of the composite was about 100 μm. Approximately 100 μm of nickel plating was then deposited on the surface of the thinned composite. Standard electropolishing by Tenupol unit was performed on the nickel-plated composite specimen and the composite specimen was examined by TEM

Energy Management in Smart Cities Based on Internet of Things: Peak Demand Reduction and Energy Savings.

Science.gov (United States)

Mahapatra, Chinmaya; Moharana, Akshaya Kumar; Leung, Victor C M

2017-12-05

Around the globe, innovation with integrating information and communication technologies (ICT) with physical infrastructure is a top priority for governments in pursuing smart, green living to improve energy efficiency, protect the environment, improve the quality of life, and bolster economy competitiveness. Cities today faces multifarious challenges, among which energy efficiency of homes and residential dwellings is a key requirement. Achieving it successfully with the help of intelligent sensors and contextual systems would help build smart cities of the future. In a Smart home environment Home Energy Management plays a critical role in finding a suitable and reliable solution to curtail the peak demand and achieve energy conservation. In this paper, a new method named as Home Energy Management as a Service (HEMaaS) is proposed which is based on neural network based Q -learning algorithm. Although several attempts have been made in the past to address similar problems, the models developed do not cater to maximize the user convenience and robustness of the system. In this paper, authors have proposed an advanced Neural Fitted Q -learning method which is self-learning and adaptive. The proposed method provides an agile, flexible and energy efficient decision making system for home energy management. A typical Canadian residential dwelling model has been used in this paper to test the proposed method. Based on analysis, it was found that the proposed method offers a fast and viable solution to reduce the demand and conserve energy during peak period. It also helps reducing the carbon footprint of residential dwellings. Once adopted, city blocks with significant residential dwellings can significantly reduce the total energy consumption by reducing or shifting their energy demand during peak period. This would definitely help local power distribution companies to optimize their resources and keep the tariff low due to curtailment of peak demand.

Energy Management in Smart Cities Based on Internet of Things: Peak Demand Reduction and Energy Savings

Directory of Open Access Journals (Sweden)

Chinmaya Mahapatra

2017-12-01

Full Text Available Around the globe, innovation with integrating information and communication technologies (ICT with physical infrastructure is a top priority for governments in pursuing smart, green living to improve energy efficiency, protect the environment, improve the quality of life, and bolster economy competitiveness. Cities today faces multifarious challenges, among which energy efficiency of homes and residential dwellings is a key requirement. Achieving it successfully with the help of intelligent sensors and contextual systems would help build smart cities of the future. In a Smart home environment Home Energy Management plays a critical role in finding a suitable and reliable solution to curtail the peak demand and achieve energy conservation. In this paper, a new method named as Home Energy Management as a Service (HEMaaS is proposed which is based on neural network based Q-learning algorithm. Although several attempts have been made in the past to address similar problems, the models developed do not cater to maximize the user convenience and robustness of the system. In this paper, authors have proposed an advanced Neural Fitted Q-learning method which is self-learning and adaptive. The proposed method provides an agile, flexible and energy efficient decision making system for home energy management. A typical Canadian residential dwelling model has been used in this paper to test the proposed method. Based on analysis, it was found that the proposed method offers a fast and viable solution to reduce the demand and conserve energy during peak period. It also helps reducing the carbon footprint of residential dwellings. Once adopted, city blocks with significant residential dwellings can significantly reduce the total energy consumption by reducing or shifting their energy demand during peak period. This would definitely help local power distribution companies to optimize their resources and keep the tariff low due to curtailment of peak demand.

Next-generation nozzle check valve significantly reduces operating costs

Energy Technology Data Exchange (ETDEWEB)

Roorda, O. [SMX International, Toronto, ON (Canada)

2009-01-15

Check valves perform an important function in preventing reverse flow and protecting plant and mechanical equipment. However, the variety of different types of valves and extreme differences in performance even within one type can change maintenance requirements and life cycle costs, amounting to millions of dollars over the typical 15-year design life of piping components. A next-generation non-slam nozzle check valve which prevents return flow has greatly reduced operating costs by protecting the mechanical equipment in a piping system. This article described the check valve varieties such as the swing check valve, a dual-plate check valve, and nozzle check valves. Advancements in optimized design of a non-slam nozzle check valve were also discussed, with particular reference to computer flow modelling such as computational fluid dynamics; computer stress modelling such as finite element analysis; and flow testing (using rapid prototype development and flow loop testing), both to improve dynamic performance and reduce hydraulic losses. The benefits of maximized dynamic performance and minimized pressure loss from the new designed valve were also outlined. It was concluded that this latest non-slam nozzle check valve design has potential applications in natural gas, liquefied natural gas, and oil pipelines, including subsea applications, as well as refineries, and petrochemical plants among others, and is suitable for horizontal and vertical installation. The result of this next-generation nozzle check valve design is not only superior performance, and effective protection of mechanical equipment but also minimized life cycle costs. 1 fig.

RESULTS FROM THE U.S. DOE 2006 SAVE ENERGY NOW ASSESSMENT INITIATIVE: DOE's Partnership with U.S. Industry to Reduce Energy Consumption, Energy Costs, and Carbon Dioxide Emissions

Energy Technology Data Exchange (ETDEWEB)

Wright, Anthony L [ORNL; Martin, Michaela A [ORNL; Gemmer, Bob [U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy; Scheihing, Paul [U.S. Department of Energy, Industrial Technologies Program; Quinn, James [U.S. Department of Energy

2007-09-01

In the wake of Hurricane Katrina and other severe storms in 2005, natural gas supplies were restricted, prices rose, and industry sought ways to reduce its natural gas use and costs. In October 2005, U.S. Department of Energy (DOE) Energy Secretary Bodman launched his Easy Ways to Save Energy campaign with a promise to provide energy assessments to 200 of the largest U.S. manufacturing plants. A major thrust of the campaign was to ensure that the nation's natural gas supplies would be adequate for all Americans, especially during home heating seasons. In a presentation to the National Press Club on October 3, 2005, Secretary Bodman said: 'America's businesses, factories, and manufacturing facilities use massive amounts of energy. To help them during this period of tightening supply and rising costs, our Department is sending teams of qualified efficiency experts to 200 of the nation's most energy-intensive factories. Our Energy Saving Teams will work with on-site managers on ways to conserve energy and use it more efficiently.' DOE's Industrial Technologies Program (ITP) responded to the Secretary's campaign with its Save Energy Now initiative, featuring a new and highly cost-effective form of energy assessments. The approach for these assessments drew heavily on the existing resources of ITP's Technology Delivery component. Over the years, ITP-Technology Delivery had worked with industry partners to assemble a suite of respected software decision tools, proven assessment protocols, training curricula, certified experts, and strong partnerships for deployment. Because of the program's earlier activities and the resources that had been developed, ITP was prepared to respond swiftly and effectively to the sudden need to promote improved industrial energy efficiency. Because of anticipated supply issues in the natural gas sector, the Save Energy Now initiative strategically focused on natural gas savings and targeted the

Recycling energy to restore impaired ankle function during human walking.

Directory of Open Access Journals (Sweden)

Steven H Collins

Full Text Available BACKGROUND: Humans normally dissipate significant energy during walking, largely at the transitions between steps. The ankle then acts to restore energy during push-off, which may be the reason that ankle impairment nearly always leads to poorer walking economy. The replacement of lost energy is necessary for steady gait, in which mechanical energy is constant on average, external dissipation is negligible, and no net work is performed over a stride. However, dissipation and replacement by muscles might not be necessary if energy were instead captured and reused by an assistive device. METHODOLOGY/PRINCIPAL FINDINGS: We developed a microprocessor-controlled artificial foot that captures some of the energy that is normally dissipated by the leg and "recycles" it as positive ankle work. In tests on subjects walking with an artificially-impaired ankle, a conventional prosthesis reduced ankle push-off work and increased net metabolic energy expenditure by 23% compared to normal walking. Energy recycling restored ankle push-off to normal and reduced the net metabolic energy penalty to 14%. CONCLUSIONS/SIGNIFICANCE: These results suggest that reduced ankle push-off contributes to the increased metabolic energy expenditure accompanying ankle impairments, and demonstrate that energy recycling can be used to reduce such cost.

Energy assessments

International Nuclear Information System (INIS)

Unruh, T.D.

1998-01-01

Energy industry initiatives during the 1970s and during the 1990s are compared. During the 1970s, the objective was to reduce energy consumption and to reduce dependency on foreign fuel. Today, the emphasis is on reducing energy costs and to improve net operating income. The challenges posed by the drive to reduce energy costs are discussed. As a tool in the drive to reduce energy cost, the energy assessment process was described. The process entails a detailed analysis of energy consumption, an investigation of energy rates and an assessment of site conditions and equipment, with a view towards an optimum combination that will lead to energy cost reductions

Green supply chain management using the queuing theory to handle congestion and reduce energy consumption and emissions from supply chain transportation fleet

International Nuclear Information System (INIS)

Aziziankohan, A.; Jolai, F.; Khalilzadeh, M.; Soltani, R.; Tavakkoli-Moghaddam, R.

2017-01-01

Purpose: Nowadays, governments and people pay more attention to use green products due to environmental pollution, irreplaceable energy and shortage of resources. Green products are resulted from the application of green supply chain management strategies to the organizations' performance strategies, so that we can reduce environmental pollutants and wastes and take a step towards saving energy with limited resources. Methodology: In this paper, the effect of reducing energy consumption in green supply chain is examined by using queuing theory and transportation models. Data was generated and solved by a commercial optimization epackage. Findings: The findings indicate that suitable assignment of existing transportation fleet with specified capacity, and using queueing theory in a closed-loop network to reduce the queue length and handle congestion, can cause a reduction in energy consumption by optimizing transportation and waiting times in a green supply chain. Originality/value: Adopting investment strategy in improving the environmental performance of the supply chain, will yield in many advantages and benefits. This article investigates the effect of queuing theory on reducing waiting time, optimizing energy consumption in green supply chain, and consequently decreasing pollution.

Green supply chain management using the queuing theory to handle congestion and reduce energy consumption and emissions from supply chain transportation fleet

Directory of Open Access Journals (Sweden)

Arvin Aziziankohan

2017-05-01

Full Text Available Purpose: Nowadays, governments and people pay more attention to use green products due to environmental pollution, irreplaceable energy and shortage of resources. Green products are resulted from the application of green supply chain management strategies to the organizations' performance strategies, so that we can reduce environmental pollutants and wastes and take a step towards saving energy with limited resources. Methodology:  In this paper, the effect of reducing energy consumption in green supply chain is examined by using queuing theory and transportation models. Data was generated and solved by a commercial optimization epackage. Findings:  The findings indicate that suitable assignment of existing transportation fleet with specified capacity, and using queueing theory in a closed-loop network to reduce the queue length and handle congestion, can cause a reduction in energy consumption by optimizing transportation and waiting times in a green supply chain. Originality/value: Adopting investment strategy in improving the environmental performance of the supply chain, will yield in many advantages and benefits. This article investigates the effect of queuing theory on reducing waiting time, optimizing energy consumption in green supply chain, and consequently decreasing pollution.

Green supply chain management using the queuing theory to handle congestion and reduce energy consumption and emissions from supply chain transportation fleet

Energy Technology Data Exchange (ETDEWEB)

Aziziankohan, A.; Jolai, F.; Khalilzadeh, M.; Soltani, R.; Tavakkoli-Moghaddam, R.

2017-07-01

Purpose: Nowadays, governments and people pay more attention to use green products due to environmental pollution, irreplaceable energy and shortage of resources. Green products are resulted from the application of green supply chain management strategies to the organizations' performance strategies, so that we can reduce environmental pollutants and wastes and take a step towards saving energy with limited resources. Methodology: In this paper, the effect of reducing energy consumption in green supply chain is examined by using queuing theory and transportation models. Data was generated and solved by a commercial optimization epackage. Findings: The findings indicate that suitable assignment of existing transportation fleet with specified capacity, and using queueing theory in a closed-loop network to reduce the queue length and handle congestion, can cause a reduction in energy consumption by optimizing transportation and waiting times in a green supply chain. Originality/value: Adopting investment strategy in improving the environmental performance of the supply chain, will yield in many advantages and benefits. This article investigates the effect of queuing theory on reducing waiting time, optimizing energy consumption in green supply chain, and consequently decreasing pollution.

Energy efficiency to reduce residential electricity and natural gas use under climate change.

Science.gov (United States)

Reyna, Janet L; Chester, Mikhail V

2017-05-15

Climate change could significantly affect consumer demand for energy in buildings, as changing temperatures may alter heating and cooling loads. Warming climates could also lead to the increased adoption and use of cooling technologies in buildings. We assess residential electricity and natural gas demand in Los Angeles, California under multiple climate change projections and investigate the potential for energy efficiency to offset increased demand. We calibrate residential energy use against metered data, accounting for differences in building materials and appliances. Under temperature increases, we find that without policy intervention, residential electricity demand could increase by as much as 41-87% between 2020 and 2060. However, aggressive policies aimed at upgrading heating/cooling systems and appliances could result in electricity use increases as low as 28%, potentially avoiding the installation of new generation capacity. We therefore recommend aggressive energy efficiency, in combination with low-carbon generation sources, to offset projected increases in residential energy demand.

Institute a modest carbon tax to reduce carbon emissions, finance clean energy technology development, cut taxes, and reduce the deficit

Energy Technology Data Exchange (ETDEWEB)

Muro, Mark; Rothwell, Jonathan

2012-11-15

The nation should institute a modest carbon tax in order to help clean up the economy and stabilize the nation’s finances. Specifically, Congress and the president should implement a $20 per ton, steadily increasing carbon excise fee that would discourage carbon dioxide emissions while shifting taxation onto pollution, financing energy efficiency (EE) and clean technology development, and providing opportunities to cut taxes or reduce the deficit. The net effect of these policies would be to curb harmful carbon emissions, improve the nation’s balance sheet, and stimulate job-creation and economic renewal.

Energy Cloud: Services for Smart Buildings

DEFF Research Database (Denmark)

Mohamed, Nader; Al-Jaroodi, Jameela; Lazarova-Molnar, Sanja

2018-01-01

, and network technologies. Using smart building energy management systems provides intelligent procedures to control buildings’ equipment such as HVAC (heating, ventilating, and air-conditioning) systems, home and office appliances, and lighting systems to reduce energy consumption while maintaining......Energy consumption in buildings is responsible for a significant portion of the total energy use and carbon emissions in large cities. One of the main approaches to reduce energy consumption and its environmental impact is to convert buildings into smart buildings using computer, software, sensor...... the required quality of living in all of the building’s spaces. This chapter discusses and reviews utilizing cloud computing to provide energy-related services to enhance the operations of smart buildings’ energy management systems. Cloud computing can provide many advantages for smart buildings’ energy...

Renewable energies for Amapa's sustainable development

International Nuclear Information System (INIS)

Marques, Ana Claudia S.; Di Lascio, Marco Alfredo; Freitas, Marcos Aurelio V.

1999-01-01

The generation of energy requires huge quantities of fuels which produce significant amounts of waste that are given back to the environment, causing remarkable damage. In order to avoid or at least reduce this damage, society is devoting research to other means of energy generation, free from that king of consequences - renewable energies. The article overviews of Amapa, Brazilian state, energy renewable sources

On the causal dynamics between emissions, nuclear energy, renewable energy, and economic growth

International Nuclear Information System (INIS)

Apergis, Nicholas; Payne, James E.; Menyah, Kojo; Wolde-Rufael, Yemane

2010-01-01

This paper examines the causal relationship between CO 2 emissions, nuclear energy consumption, renewable energy consumption, and economic growth for a group of 19 developed and developing countries for the period 1984-2007 using a panel error correction model. The long-run estimates indicate that there is a statistically significant negative association between nuclear energy consumption and emissions, but a statistically significant positive relationship between emissions and renewable energy consumption. The results from the panel Granger causality tests suggest that in the short-run nuclear energy consumption plays an important role in reducing CO 2 emissions whereas renewable energy consumption does not contribute to reductions in emissions. This may be due to the lack of adequate storage technology to overcome intermittent supply problems as a result electricity producers have to rely on emission generating energy sources to meet peak load demand. (author)

Applying data envelopment analysis approach to improve energy efficiency and reduce GHG (greenhouse gas) emission of wheat production

International Nuclear Information System (INIS)

Khoshnevisan, Benyamin; Rafiee, Shahin; Omid, Mahmoud; Mousazadeh, Hossein

2013-01-01

In this study, DEA (data envelopment analysis) was applied to analyze the energy efficiency of wheat farms in order to separate efficient and inefficient growers and to calculate the wasteful uses of energy. Additionally, the degrees of TE (technical efficiency), PTE (pure technical efficiency) and SE (scale efficiency) were determined. Furthermore, the effect of energy optimization on GHG (greenhouse gas) emission was investigated and the total amount of GHG emission of efficient farms was compared with inefficient ones. Based on the results it was revealed that 18% of producers were technically efficient and the average of TE was calculated as 0.82. Based on the BCC (Banker–Charnes–Cooper) model 154 growers (59%) were identified efficient and the mean PTE of these farmers was found to be 0.99. Also, it was concluded that 2075.8 MJ ha −1 of energy inputs can be saved if the performance of inefficient farms rises to a high level. Additionally, it was observed that the total GHG emission from efficient and inefficient producers was 2713.3 and 2740.8 kg CO 2eq . ha −1 , respectively. By energy optimization the total GHG emission can be reduced to the value of 2684.29 kg CO 2eq . ha −1 . - Highlights: • 18% of producers were technically efficient and the average of TE was 0.82. • An average 2075.8 MJ ha −1 from energy input could be saved without reducing the yield. • GHG emission of efficient and inefficient producers was 2713.3 and 2740.8 kg CO 2eq. ha −1 . • Total GHG emission can be reduced to the value of 2684.29 kg CO 2eq. ha −1

Intriguing model significantly reduces boarding of psychiatric patients, need for inpatient hospitalization.

Science.gov (United States)

2015-01-01

As new approaches to the care of psychiatric emergencies emerge, one solution is gaining particular traction. Under the Alameda model, which has been put into practice in Alameda County, CA, patients who are brought to regional EDs with emergency psychiatric issues are quickly transferred to a designated emergency psychiatric facility as soon as they are medically stabilized. This alleviates boarding problems in area EDs while also quickly connecting patients with specialized care. With data in hand on the model's effectiveness, developers believe the approach could alleviate boarding problems in other communities as well. The model is funded by through a billing code established by California's Medicaid program for crisis stabilization services. Currently, only 22% of the patients brought to the emergency psychiatric facility ultimately need to be hospitalized; the other 78% are able to go home or to an alternative situation. In a 30-day study of the model, involving five community hospitals in Alameda County, CA, researchers found that ED boarding times were as much as 80% lower than comparable ED averages, and that patients were stabilized at least 75% of the time, significantly reducing the need for inpatient hospitalization.

Reducing conflicts between climate policy and energy policy in the US: The important role of the states

International Nuclear Information System (INIS)

Peterson, Thomas D.; Rose, Adam Z.

2006-01-01

The absence of US national action on global climate change policy has prompted initiatives by the US Congress, cities, states, and regions toward what is likely to become a long-term, collaborative effort to harmonize national energy and climate policies. This upward evolution in the face of a reluctant administration is historically consistent with the development of national legislation on other environmental and social issues in the US. At the heart of this movement is the need to resolve conflicts between high-intensity use of low-cost fossil energy supplies, and the dominating impact of carbon dioxide emissions on global climate change. US states are among the largest carbon dioxide emitters in the world and play a critical role in supplying and transforming energy, as well as consuming it, for economic advantage. State governments are also likely to have to shoulder some of the cost of potentially extensive climate damages and bear the brunt of the cost of implementing future federal mandates. As a result, many are taking proactive stances on the development of climate mitigation policy to prepare for, accelerate, and/or guide national policy. As US states show leadership on addressing greenhouse gas emissions, they also play an important role in forging policies and measures that reduce economic conflict between energy and climate goals. A number have launched or completed greenhouse gas mitigation plans and other major policies in the past few years that address these conflicts through: (1) finding ways to reduce mitigation costs, including the use of incentive-based policy instruments; (2) promoting an open and democratic policy process that includes major stakeholders; (3) promoting equity across socioeconomic groups, regions, and generations; and (4) promoting interregional cooperation. The results are promising and suggest that the state arena for climate and energy policy is evolving quickly and constructively toward alternatives that reduce conflict

The potential of dual-energy virtual monochromatic imaging in reducing renal cyst pseudoenhancement. A phantom study

International Nuclear Information System (INIS)

Yamada, Sachiko; Ueguchi, Takashi; Ukai, Isao; Nagai, Yumiko; Yamakawa, Masanobu; Shimosegawa, Eku; Shimazu, Takeshi; Hatazawa, Jun

2012-01-01

Renal cyst pseudoenhancement, an artifactual increase of computed tomography (CT) attenuation for cysts with increased iodine concentrations in the renal parenchyma, complicates the classification of cysts and may thus lead to the mischaracterization of a benign non-enhancing lesion as an enhancing mass. The purpose of this study was to use a phantom model to assess the ability of dual-energy virtual monochromatic imaging to reduce renal pseudoenhancement. A water-filled cylindrical cyst model suspended in varying concentrations of iodine solution, to simulate varying levels of parenchymal enhancement, was scanned with a dual-energy CT scanner using the following three scanning protocols with different combinations of tube voltage: 80 and 140 kV; 80 and 140 kV with tin filter; and 100 and 140 kV with tin filter. Virtual monochromatic images were then synthesized for each dual-energy scan. Single-energy scan with a tube voltage of 120 kV was also performed to obtain polychromatic images as controls. Mean attenuation values (in Hounsfield units) of cyst proxies were measured on both polychromatic and virtual monochromatic images. Pseudoenhancement was considered to be present when the cyst attenuation level increased by more than 10 HU (Hounsfield Unit) as the background iodine concentration increased from 0.0% to 0.4%, 1.5%, or 2.5%. Our results revealed that pseudoenhancement was not observed on any of the monochromatic images, but appeared on polychromatic images at a background iodine concentration of 2.5%. We thus conclude that dual-energy virtual monochromatic images have a potential to reduce renal pseudoenhancement. (author)

Effect of reducing portion size at a compulsory meal on later energy intake, gut hormones, and appetite in overweight adults.

OpenAIRE

Lewis, HB; Ahern, AL; Solis-Trapala, I; Walker, CG; Reimann, F; Gribble, FM; Jebb, SA

2015-01-01

OBJECTIVE: Larger portion sizes (PS) are associated with greater energy intake (EI), but little evidence exists on the appetitive effects of PS reduction. This study investigated the impact of reducing breakfast PS on subsequent EI, postprandial gastrointestinal hormone responses, and appetite ratings. METHODS: In a randomized crossover design (n = 33 adults; mean BMI 29 kg/m(2) ), a compulsory breakfast was based on 25% of gender-specific estimated daily energy requirements; PS was reduced b...

Significant association between sulfate-reducing bacteria and uranium-reducing microbial communities as revealed by a combined massively parallel sequencing-indicator species approach.

Science.gov (United States)

Cardenas, Erick; Wu, Wei-Min; Leigh, Mary Beth; Carley, Jack; Carroll, Sue; Gentry, Terry; Luo, Jian; Watson, David; Gu, Baohua; Ginder-Vogel, Matthew; Kitanidis, Peter K; Jardine, Philip M; Zhou, Jizhong; Criddle, Craig S; Marsh, Terence L; Tiedje, James M

2010-10-01

Massively parallel sequencing has provided a more affordable and high-throughput method to study microbial communities, although it has mostly been used in an exploratory fashion. We combined pyrosequencing with a strict indicator species statistical analysis to test if bacteria specifically responded to ethanol injection that successfully promoted dissimilatory uranium(VI) reduction in the subsurface of a uranium contamination plume at the Oak Ridge Field Research Center in Tennessee. Remediation was achieved with a hydraulic flow control consisting of an inner loop, where ethanol was injected, and an outer loop for flow-field protection. This strategy reduced uranium concentrations in groundwater to levels below 0.126 μM and created geochemical gradients in electron donors from the inner-loop injection well toward the outer loop and downgradient flow path. Our analysis with 15 sediment samples from the entire test area found significant indicator species that showed a high degree of adaptation to the three different hydrochemical-created conditions. Castellaniella and Rhodanobacter characterized areas with low pH, heavy metals, and low bioactivity, while sulfate-, Fe(III)-, and U(VI)-reducing bacteria (Desulfovibrio, Anaeromyxobacter, and Desulfosporosinus) were indicators of areas where U(VI) reduction occurred. The abundance of these bacteria, as well as the Fe(III) and U(VI) reducer Geobacter, correlated with the hydraulic connectivity to the substrate injection site, suggesting that the selected populations were a direct response to electron donor addition by the groundwater flow path. A false-discovery-rate approach was implemented to discard false-positive results by chance, given the large amount of data compared.

One day of moderate energy deficit reduces fasting and postprandial triacylglycerolemia in women: the role of calorie restriction and exercise.

Science.gov (United States)

Maraki, Maria; Magkos, Faidon; Christodoulou, Nektarios; Aggelopoulou, Niki; Skenderi, Katerina P; Panagiotakos, Demosthenes; Kavouras, Stavros A; Sidossis, Labros S

2010-08-01

Fasting and postprandial hypertriacylglycerolemia are important cardiovascular risk factors in women. We sought to examine the effects of acute (1 day), moderate ( approximately 2 MJ) energy deficit induced by calorie restriction, exercise, or combination of both on fasting and postprandial triacylglycerol (TAG) metabolism in women. Six healthy premenopausal women performed four oral fat tolerance tests in the morning after a day of a) rest (control), b) calorie restriction ( approximately 2 MJ), c) exercise (net deficit of approximately 2 MJ) and d) calorie restriction-plus-exercise (total energy deficit of approximately 2 MJ). All energy deficit trials significantly reduced fasting and postprandial total plasma TAG concentrations by 15-23% and 12-23%, respectively, and triacylglycerol-rich lipoprotein TAG concentrations by 37-43% and 25-39%, respectively, compared with the control condition (Pwomen. Exercise elicits a somewhat greater effect than calorie restriction in the postprandial state. The acute effect of diet and exercise should be taken into account when studying the long-term effects of weight loss and exercise training on TAG metabolism. Copyright 2009 Elsevier Ltd and European Society for Clinical Nutrition and Metabolism. All rights reserved.

Energy-efficient wireless mesh infrastructures

OpenAIRE

Al-Hazmi, Y.; de Meer, Hermann; Hummel, Karin Anna; Meyer, Harald; Meo, Michela; Remondo Bueno, David

2011-01-01

The Internet comprises access segments with wired and wireless technologies. In the future, we can expect wireless mesh infrastructures (WMIs) to proliferate in this context. Due to the relatively low energy efficiency of wireless transmission, as compared to wired transmission, energy consumption of WMIs can represent a significant part of the energy consumption of the Internet as a whole. We explore different approaches to reduce energy consumption in WMIs, taking into accoun...

Maternal Dietary Counseling Reduces Consumption of Energy-Dense Foods among Infants: A Randomized Controlled Trial

Science.gov (United States)

Vitolo, Marcia Regina; Bortolini, Gisele Ane; Campagnolo, Paula Dal Bo; Hoffman, Daniel J.

2012-01-01

Objective: To evaluate the impact of a dietary counseling in reducing the intake of energy-dense foods by infants. Design: A randomized controlled trial. Setting and Participants: Sao Leopoldo, Brazil. Mothers and infants of a low-income-group population were randomized into intervention (n = 163) and received dietary counseling during 10 home…

[Reduce Energy Costs While Maintaining Healthy IAQ.] "Indoor Air Quality Tools for Schools" Update #17

Science.gov (United States)

US Environmental Protection Agency, 2009

2009-01-01

This issue of "Indoor Air Quality Tools for Schools" Update ("IAQ TfS" Update) contains the following items: (1) News and Events; (2) Feature Article: Reduce Energy Costs while Maintaining Healthy IAQ; (3) Insight into Excellence: North East Independent School District ; (4) School Building Week 2009; and (5) Have Your Questions Answered!

Reducing urban heat island effects to improve urban comfort and balance energy consumption in Bucharest (Romania)

Science.gov (United States)

Constantinescu, Dan; Ochinciuc, Cristina Victoria; Cheval, Sorin; Comşa, Ionuţ; Sîrodoev, Igor; Andone, Radu; Caracaş, Gabriela; Crăciun, Cerasella; Dumitrescu, Alexandru; Georgescu, Mihaela; Ianoş, Ioan; Merciu, Cristina; Moraru, Dan; Opriş, Ana; Paraschiv, Mirela; Raeţchi, Sonia; Saghin, Irina; Schvab, Andrei; Tătui-Văidianu, Nataşa

2017-04-01

In the recent decades, extreme temperature events and derived hazards are frequent and trigger noteworthy impacts in Romania, especially over the large urban areas. The cities produce significant disturbances of many elements of the regional climate, and generates adverse effects such as Urban Heat Islands (UHI). This presentation condenses the outputs of an ongoing research project (REDBHI) developed through (2013-2017) focused on developing a methodology for monitoring and forecasting indoor climate and energy challenges related to the intensity of UHI of Bucharest (Romania), based on relevant urban climate zones (UCZs). Multi-criteria correlations between the UHI and architectural, urban and landscape variables were determined, and the vulnerability of buildings expressed in the form of transfer function between indoor micro-climate and outdoor urban environment. The vulnerability of civil buildings was determined in relation with the potential for amplifying the thermal hazards intensity through the anthropogenic influence. The project REDBHI aims at developing innovative and original products, with direct applicability, which can be used in any urban settlement and have market potential with regards to energy design and consulting. The concrete innovative outcomes consist of a) localization of the Bucharest UCZs according to the UHI intensity, identifying reference buildings and sub-zones according to urban anthropic factors and landscape pattern; b) typology of representative buildings with regards to energy consumption and CO2 emitted as a result of building exploitation; c) 3D modelling of the reference buildings and of the thermal/energy reaction to severe climatic conditions d) empirical validation of the dynamic thermal/energy analysis; d) development of an pilot virtual studio capable to simulate climate alerts, analyse scenarios and suggest measures to mitigate the UHI effects, and disseminate the outcomes for educational purposes; e) compendium of

Refrigeration: Introducing energy saving opportunities for business

Energy Technology Data Exchange (ETDEWEB)

NONE

2006-04-15

In some industries, most notably food and drink and chemicals, refrigeration accounts for a significant proportion of overall site energy costs. For instance, in the industrial handling of meat, poultry and fish, it often accounts for 50% of total energy costs. In ice-cream production the proportion is 70%. In a number of commercial sectors, refrigeration also represents a significant proportion of overall energy costs. For example: Cold storage 90%; Food supermarkets 50%; Small shops with refrigerated cabinets 70% or over; Pubs and clubs 30%. Against these high costs, even a small reduction in refrigeration energy use can offer significant cost savings, resulting in increased profits. Energy saving need not be expensive. Energy savings of up to 20% can be realised in many refrigeration plant through actions that require little or no investment. In addition, improving the efficiency and reducing the load on a refrigeration plant can improve reliability and reduce the likelihood of a breakdown. Most organisations can save energy and money on refrigeration by: More efficient equipment; Good maintenance; Housekeeping and control. This publication provides an understanding of the operation of refrigeration systems, identifies where savings can be realised and will enable readers to present an informed case on energy savings to key decision makers within their organisation. (GB)

Can the household sector reduce global warming mitigation costs? sensitivity to key parameters in a TIMES techno-economic energy model

International Nuclear Information System (INIS)

Astudillo, Miguel F.; Vaillancourt, Kathleen; Pineau, Pierre-Olivier; Amor, Ben

2017-01-01

Highlights: •An energy system model of Quebec is combined with building simulation software. •Greenhouse gas emission reductions efforts increase annual electricity peak demand. •Alternative heating tech. And building envelopes can effectively reduce peak demand. •Denser urban developments massively reduced costs of global warming mitigation. •CO 2 emissions from hydropower reservoirs are relevant in global warming mitigation. -- Abstract: The transition to low carbon societies may increase peak electricity demand, which can be costly to supply with renewable energy, whose availability is uncertain. Buildings are often the main cause of peak demand, and they are believed to hold a large unrealised energy-efficiency potential. If realised, this potential could considerably mitigate the transition costs to low carbon societies, reducing average and peak electricity demands. We explore this potential in several cost-optimal global warming (GW) mitigation scenarios using a multi-sector TIMES energy system model of the province of Quebec for the period 2011–2050. Heating and conservation measures in the residential sector are modelled using building simulations and parameters’ values from the literature. The intra-annual availability of renewable energy and electricity imports is derived from time-series analysis. Additionally, the influence of key parameters such as the projections of primary energy demand and emissions from reservoir impoundment is evaluated. Finally, we discuss some of the barriers that could hamper the energy transition and how they can be overcome. Results indicate that peak demand would rise by 30% due to GW mitigation efforts, but it can be effectively reduced by interventions in the residential sector. Heat pumps are the most cost effective heating technology, despite their lower efficiencies in cold climates. Better-insulated building envelopes have an important role in new houses, reducing by 14% the GW mitigation costs and

Lime and Phosphate Amendment Can Significantly Reduce Uptake of Cd and Pb by Field-Grown Rice

Directory of Open Access Journals (Sweden)

Rongbo Xiao

2017-03-01

Full Text Available Agricultural soils are suffering from increasing heavy metal pollution, among which, paddy soil polluted by heavy metals is frequently reported and has elicited great public concern. In this study, we carried out field experiments on paddy soil around a Pb-Zn mine to study amelioration effects of four soil amendments on uptake of Cd and Pb by rice, and to make recommendations for paddy soil heavy metal remediation, particularly for combined pollution of Cd and Pb. The results showed that all the four treatments can significantly reduce the Cd and Pb content in the late rice grain compared with the early rice, among which, the combination amendment of lime and phosphate had the best remediation effects where rice grain Cd content was reduced by 85% and 61%, respectively, for the late rice and the early rice, and by 30% in the late rice grain for Pb. The high reduction effects under the Ca + P treatment might be attributed to increase of soil pH from 5.5 to 6.7. We also found that influence of the Ca + P treatment on rice production was insignificant, while the available Cd and Pb content in soil was reduced by 16.5% and 11.7%, respectively.

Capacity Development and Strengthening for Energy Policy formulation and implementation of Sustainable Energy Projects in Indonesia CASINDO. Deliverable No. 24. Regional Energy Efficiency Planning 2011 [for Yogyakarta

Energy Technology Data Exchange (ETDEWEB)

Prahara, Pamungkas Jutta; Hariadi, T.K. [Universitas Muhammadiyah PUSPER-UMY, Yogyakarta (Indonesia)

2012-06-15

The overall objective of the CASINDO programme is to establish a self-sustaining and self-developing structure at both the national and regional level to build and strengthen human capacity to enable the provinces of North Sumatra, Yogyakarta, Central Java, West Nusa Tenggara and Papua to formulate sound policies for renewable energy and energy efficiency and to develop and implement sustainable energy projects. Increasing energy demand and decreasing energy supply has to be faced by strategic measures. Daerah Istimewa Yogyakarta (DIY) faces the same problem with more burdens since DIY depends on energy supply from other region. One strategic measure is to reduce energy consumption across sectors. There are, in total, 805.468 electricity consumers in Yogyakarta in the household, social and industrial sector. Through direct measures electricity consumption can be reduced and financial resources can be saved. One of the measures is energy conservation campaign to all sectors in the region which expected to reduce the energy spent, for example to switch off electronic devices totally instead of to put them in standby mode. Survey in the region indicated there are various use of electronic devices in household dominated by refrigeration, television, and AC's. In industries and social, AC and motors are dominating the sector. By applying inverter technology and refrigerant retrofitting to air conditioner can reduce significantly the energy consumption. Changing from old refrigerator with new energy saver refrigerator would also reduce energy consumption. Strategic energy policy and tools has to be identified to push the community to apply the recommended measure. Energy labeling, tax reduction program and energy price increase would make the energy conservation program more feasible and create an environment where inventing in energy efficiency is more attractive. Furthermore a financial resource policy has to be prepared for community education through promotion

Development of Energy Efficiency Indicators in Russia

Energy Technology Data Exchange (ETDEWEB)

NONE

2011-07-01

Russia is sometimes referred to as 'the Saudi Arabia of energy efficiency'; its vast potential to reduce energy consumption can be considered a significant 'energy reserve'. Russia, recognising the benefits of more efficient use of energy, is taking measures to exploit this potential. The president has set the goal to reduce energy intensity by 40% between 2007 and 2020. In the past few years, the IEA has worked closely with Russian authorities to support the development of energy efficiency indicators in Russia, critical to an effective implementation and monitoring of Russia's ambitious energy intensity and efficiency goals. The key findings of the IEA work with Russia on developing energy efficiency indicators form the core of this report.

Reducing Energy Burden with Solar: Colorado's Strategy and Roadmap for States

Energy Technology Data Exchange (ETDEWEB)

Cook, Jeffrey J. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Shah, Monisha [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2018-03-03

The Colorado Energy Office (CEO) recently implemented a multi-pronged strategy to reduce energy burden for low-income (LI) Colorado residents through the deployment of solar electricity generation. Due to these efforts, approximately 20 MW of photovoltaic (PV) solar may be deployed in Colorado by the end of 2019 specifically for low-income households. Relying on interviews with ten subject-matter experts and other research, this report outlines the details of the CEO strategy including why the agency pursued this strategy, how it was carried out, and lessons learned from implementation. Though CEO's strategy is unique and tailored to the needs of Colorado, it is possible that other states might learn from CEO's experiences when designing their own LI strategies. As a result, the report concludes by outlining six primary steps for designing a comprehensive low-income solar strategy.

A STRATEGIC PROGRAM TO REDUCE GREENHOUSE GASES EMISSIONS PRODUCED FROM FOOD INDUSTRY

Energy Technology Data Exchange (ETDEWEB)

A. Kilic [Faculty of Science, Department of Biology, University of Nigde, Nigde (Turkey); A. Midilli [Faculty of Engineering, Department of Mechanical Engineering, Nigde (Turkey); I. Dincer [Faculty of Engineering and Applied Science, University of Ontario Institute of Technology, Oshawa, ON (Canada)

2008-09-30

Greenhouse gases (GHGs) emissions are at every stage of conventional food production (planting, harvesting, irrigation, food production, transportation, and application of pesticides and fertilizers, etc.). In this study, a strategic program is proposed to reduce GHGs emissions resulting during conventional food production. The factors which form the basis of this strategic program are energy, environment and sustainability. The results show that the application of sustainable food processing technologies can significantly reduce GHGs emissions resulting from food industry. Moreover, minimizing the utilization of fossil-fuel energy sources and maximizing the utilization of renewable energy sources results in the reduction of GHGs emissions during food production, which in turn reduces the effect of global warming.

Geothermy, a significant energy source in the Republic of Macedonia

International Nuclear Information System (INIS)

Kotevski, Georgi; Sutinova, Jagoda; Donev, S.; Novkovski, Todor

1995-01-01

According to the recent investigations, it is ascertain that the Republic of Macedonia is one of the richest thermal waters regions. Therefore, the territory of Macedonia is a perspective terrain for geothermal energy exploration. The aim of this paper is to point out the main localities that are priority for further geothermal energy investigations. The chemical analysis of the Macedonian geothermal waters is also presented

The impacts on U.S. energy markets and the economy of reducing oil imports. Service report

International Nuclear Information System (INIS)

1996-09-01

The General Accounting Office (GAO) has responded to a request from Representative John Kasich by requesting that the Energy Information Administration (EIA) use the National Energy Modeling System (NEMS) to estimate the cost to the U.S. economy of reducing oil imports. The analysis summarized by this paper focuses on two approaches toward a target reduction in oil imports: (1) a set of cases with alternative world crude oil price trajectories, and (2) two cases which investigates the use of an oil import fee

New electric technologies to reduce global warming impacts

International Nuclear Information System (INIS)

Courtright, H.A.

1994-01-01

Advanced electric technologies hold significant potential to reduce global warming impact through reduction of primary fuel needed to power end-use applications. These reductions can occur in two forms: (1) reduced kilowatt-hour usage and power plant emissions through efficiency improvements and technological enhancements of existing electrically-driven applications; (2) the development of new electric technologies to replace traditional fossil-fuel driven applications which can result in less overall primary energy consumption and lower overall emissions. Numerous new electric technologies are presently being developed by the Electric Power Research Institute. The technologies reviewed in this paper include: Microwave Fabric Dryer, Advanced Heat Pumps, Heat Pump Water Heater, Infrared Sand Reclaimer, Freeze Concentration, Membrane Water Recovery, Microwave Petrochemical Production, Infrared Drying, and Electric Vehicles. Full commercialization of these technologies can result in significant energy savings and CO 2 reductions, in addition to improving the competitiveness of businesses using these technologies

Energy prospects

International Nuclear Information System (INIS)

Lyall, K.

1991-01-01

The Business Council of Australia's study on Prospects for Improved Energy Efficiency and the Application of Renewable Energy Resources is summarised. The study estimates that replacement of all off-peak electric units in Australia with solar gas boosted systems would reduce electricity consumption for residential water heating by approximately 25% and almost halve carbon dioxide emissions resulting from residential water heating. Furthermore, substitution of all water heating units in Australia with solar gas systems would reduce total emissions by about 80%. The study concludes that while substitution on such a scale could not readily be achieved even within several decades, the estimates do indicate the significant benefits that might be realised by a long term program. 2 refs., 3 tabs

Weight-sparing effect of insulin detemir: a consequence of central nervous system-mediated reduced energy intake?

Science.gov (United States)

Russell-Jones, D; Danne, T; Hermansen, K; Niswender, K; Robertson, K; Thalange, N; Vasselli, J R; Yildiz, B; Häring, H U

2015-10-01

Insulin therapy is often associated with adverse weight gain. This is attributable, at least in part, to changes in energy balance and insulin's anabolic effects. Adverse weight gain increases the risk of poor macrovascular outcomes in people with diabetes and should therefore be mitigated if possible. Clinical studies have shown that insulin detemir, a basal insulin analogue, exerts a unique weight-sparing effect compared with other basal insulins. To understand this property, several hypotheses have been proposed. These explore the interplay of efferent and afferent signals between the muscles, brain, liver, renal and adipose tissues in response to insulin detemir and comparator basal insulins. The following models have been proposed: insulin detemir may reduce food intake through direct or indirect effects on the central nervous system (CNS); it may have favourable actions on hepatic glucose metabolism through a selective effect on the liver, or it may influence fluid homeostasis through renal effects. Studies have consistently shown that insulin detemir reduces energy intake, and moreover, it is clear that this shift in energy balance is not a consequence of reduced hypoglycaemia. CNS effects may be mediated by direct action, by indirect stimulation by peripheral mediators and/or via a more physiological counter-regulatory response to insulin through restoration of the hepatic-peripheral insulin gradient. Although the precise mechanism remains unclear, it is likely that the weight-sparing effect of insulin detemir can be explained by a combination of mechanisms. The evidence for each hypothesis is considered in this review. © 2015 The Authors. Diabetes, Obesity and Metabolism published by John Wiley & Sons Ltd.

Incorporation of catalytic dehydrogenation into fischer-tropsch synthesis to significantly reduce carbon dioxide emissions

Science.gov (United States)

Huffman, Gerald P.

2012-11-13

A new method of producing liquid transportation fuels from coal and other hydrocarbons that significantly reduces carbon dioxide emissions by combining Fischer-Tropsch synthesis with catalytic dehydrogenation is claimed. Catalytic dehydrogenation (CDH) of the gaseous products (C1-C4) of Fischer-Tropsch synthesis (FTS) can produce large quantities of hydrogen while converting the carbon to multi-walled carbon nanotubes (MWCNT). Incorporation of CDH into a FTS-CDH plant converting coal to liquid fuels can eliminate all or most of the CO.sub.2 emissions from the water-gas shift (WGS) reaction that is currently used to elevate the H.sub.2 level of coal-derived syngas for FTS. Additionally, the FTS-CDH process saves large amounts of water used by the WGS reaction and produces a valuable by-product, MWCNT.

Do Renewable Energy Policies Reduce Carbon Emissions? On Caps and Intra-Jurisdictional Leakage

OpenAIRE

Perino, Grischa; Jarke, Johannes

2015-01-01

Climate policies overlapping a cap-and-trade scheme are generally considered not to change domestic emissions. In a two-sector general equilibrium model where only one sector is covered by a cap, we find that such policies do have a net impact on carbon emissions through inter-sectoral leakage. Promotion of renewable energy reduces emissions if tax-funded, but can increase emissions if funded by a levy on electricity. Replacing fossil fuels by electricity in uncapped sectors (e.g. power-to-he...

Introducing renewable energy in vineyards and agricultural machinery: A way to reduce emissions and provide sustainability

Directory of Open Access Journals (Sweden)

Javier Carroquino

2018-03-01

Full Text Available Climate change, depletion of nonrenewable resources in the current energies, pollution from them and the greater ecological awareness of the population, are factors that suggest the change of energy sources in business. The wine industry is concerned about sustainability and with a clear awareness of what climate change may mean for it. This sector is supposed to have a high receptivity to the implementation of clean energy, as this favours not only the environment but also the essence of its business. This work shows how the use of renewable energy, on a small scale, can be profitable in both vineyards and wineries. For this purpose, the European project LIFE REWIND (Renewable energy in the wine industry has developed several actions, including the installation and operation of a prototype in a Spanish winery. This paper shows how to introduce renewable energy in wineries and vineyards in a profitable way, reducing the emissions of CO2 associated to the activity and the product, without changing the processes of cultivation or production.

Strategies for Reducing Energy Consumption in a Student Cafeteria in a Hot-Humid Climate: A Case Study

Directory of Open Access Journals (Sweden)

Mohammed Alhaji Mohammed

2013-03-01

Full Text Available Increasing attention is being given to energy consumption and potential for energy savings in public buildings in order to improve energy performance. Due to their size and functional requirements, public buildings especially cafeteria facilities tend to consume a significant amount of energy. Furthermore, due to their operational characteristics and construction pattern, unnecessary energy is likely to be used for maintaining acceptable indoor environmental quality. In this study, a student cafeteria at King Fahd University of Petroleum and Minerals, Saudi Arabia, was selected for the assessment of its energy performance and potential energy conservation opportunities. Energy simulation software Visual DOE 4.1 was used to develop an energy performance model for assessing various energy conservation measures pertinent to the building envelope and HVAC system design. Data required for setting up the model were gathered through simple energy audits. The architectural and mechanical drawings and the history of electrical consumption were collected. Various energy conservation strategies were then implemented including standards, single and combined energy conservation measures. These measures resulted in a combined design saving of 27.4%, the HVAC system saving 10.6%, implementation of standards saving about 16.7%, lighting 6.6%, equipment 2.6%, insulation 2.5% and glazing 1.4%. Based on these results, it is apparent that there is a significant potential for improving energy performance and justification to employ the suggested measures for achieving substantial energy savings and minimize energy consumption.

On the causal dynamics between emissions, nuclear energy, renewable energy, and economic growth

Energy Technology Data Exchange (ETDEWEB)

Apergis, Nicholas [Department of Banking and Financial Management, University of Piraeus, Karaoli and Dimitriou 80, Piraeus, ATTIKI 18534 (Greece); Payne, James E. [Department of Economics, Illinois State University, Normal, IL 61790-4200 (United States); Menyah, Kojo [London Metropolitan Business School, London Metropolitan University, 84 Moorgate, London, EC2M 6SQ (United Kingdom); Wolde-Rufael, Yemane

2010-09-15

This paper examines the causal relationship between CO{sub 2} emissions, nuclear energy consumption, renewable energy consumption, and economic growth for a group of 19 developed and developing countries for the period 1984-2007 using a panel error correction model. The long-run estimates indicate that there is a statistically significant negative association between nuclear energy consumption and emissions, but a statistically significant positive relationship between emissions and renewable energy consumption. The results from the panel Granger causality tests suggest that in the short-run nuclear energy consumption plays an important role in reducing CO{sub 2} emissions whereas renewable energy consumption does not contribute to reductions in emissions. This may be due to the lack of adequate storage technology to overcome intermittent supply problems as a result electricity producers have to rely on emission generating energy sources to meet peak load demand. (author)

Reducing Data Center Loads for a Large-Scale, Low-Energy Office Building: NREL's Research Support Facility (Book)

Energy Technology Data Exchange (ETDEWEB)

Sheppy, M.; Lobato, C.; Van Geet, O.; Pless, S.; Donovan, K.; Powers, C.

2011-12-01

overcame them. The IT settings and strategies outlined in this document have been used to significantly reduce data center energy requirements in the RSF; however, these can also be used in existing buildings and retrofits.

The Energy Future.

Science.gov (United States)

Newman, John; Bonino, Christopher A; Trainham, James A

2018-06-07

The foreseeable energy future will be driven by economics of known technologies and the desire to reduce CO 2 emissions to the atmosphere. Renewable energy options are compared with each other and with the use of fossil fuels with carbon capture and sequestration (CCS). Economic analysis is used to determine the best of several alternatives. One can disagree on the detailed costs, including externalities such as climate change and air and water pollution. But the differences in capital and operating costs between known technologies are so significant that one can draw clear conclusions. Results show that renewable energy cannot compete with fossil fuels on a cost basis alone because energy is intrinsic to the molecule, except for hydroelectricity. However, fossil fuels are implicated in climate change. Using renewable energy exclusively, including transportation and electricity needs, could reduce the standard of living in the United States by 43% to 62%, which would correspond to the level in about 1970. If capture and sequester of CO 2 are implemented, the cost of using fossil fuels will increase, but they beat renewable energy handily as an economic way to produce clean energy.

Linseed dietary fibers reduce apparent digestibility of energy and fat and weight gain in growing rats

DEFF Research Database (Denmark)

Kristensen, M.; Knudsen, K. E. B.; Jørgensen, H.

2013-01-01

Dietary fibers (DF) may affect energy balance, an effect often ascribed to the viscous nature of some water soluble DF, which affect luminal viscosity and thus multiple physiological processes. We have tested the hypothesis that viscous linseed DF reduce apparent nutrient digestibility, and limit...

Iron oxide/aluminum/graphene energetic nanocomposites synthesized by atomic layer deposition: Enhanced energy release and reduced electrostatic ignition hazard

Science.gov (United States)

Yan, Ning; Qin, Lijun; Hao, Haixia; Hui, Longfei; Zhao, Fengqi; Feng, Hao

2017-06-01

Nanocomposites consisting of iron oxide (Fe2O3) and nano-sized aluminum (Al), possessing outstanding exothermic redox reaction characteristics, are highly promising nanothermite materials. However, the reactant diffusion inhibited in the solid state system makes the fast and complete energy release very challenging. In this work, Al nanoparticles anchored on graphene oxide (GO/Al) was initially prepared by a solution assembly approach. Fe2O3 was deposited on GO/Al substrates by atomic layer deposition (ALD). Simultaneously thermal reduction of GO occurs, resulting in rGO/Al@Fe2O3 energetic composites. Differential scanning calorimetry (DSC) analysis reveals that rGO/Al@Fe2O3 composite containing 4.8 wt% of rGO exhibits a 50% increase of the energy release compared to the Al@Fe2O3 nanothermite synthesized by ALD, and an increase of about 130% compared to a random mixture of rGO/Al/Fe2O3 nanoparticles. The enhanced energy release of rGO/Al@Fe2O3 is attributed to the improved spatial distribution as well as the increased interfacial intimacy between the oxidizer and the fuel. Moreover, the rGO/Al@Fe2O3 composite with an rGO content of 9.6 wt% exhibits significantly reduced electrostatic discharge sensitivity. These findings may inspire potential pathways for engineering energetic nanocomposites with enhanced energy release and improved safety characteristics.

Unconventional energy resources in a crowded subsurface: Reducing uncertainty and developing a separation zone concept for resource estimation and deep 3D subsurface planning using legacy mining data.

Science.gov (United States)

Monaghan, Alison A

2017-12-01

Over significant areas of the UK and western Europe, anthropogenic alteration of the subsurface by mining of coal has occurred beneath highly populated areas which are now considering a multiplicity of 'low carbon' unconventional energy resources including shale gas and oil, coal bed methane, geothermal energy and energy storage. To enable decision making on the 3D planning, licensing and extraction of these resources requires reduced uncertainty around complex geology and hydrogeological and geomechanical processes. An exemplar from the Carboniferous of central Scotland, UK, illustrates how, in areas lacking hydrocarbon well production data and 3D seismic surveys, legacy coal mine plans and associated boreholes provide valuable data that can be used to reduce the uncertainty around geometry and faulting of subsurface energy resources. However, legacy coal mines also limit unconventional resource volumes since mines and associated shafts alter the stress and hydrogeochemical state of the subsurface, commonly forming pathways to the surface. To reduce the risk of subsurface connections between energy resources, an example of an adapted methodology is described for shale gas/oil resource estimation to include a vertical separation or 'stand-off' zone between the deepest mine workings, to ensure the hydraulic fracturing required for shale resource production would not intersect legacy coal mines. Whilst the size of such separation zones requires further work, developing the concept of 3D spatial separation and planning is key to utilising the crowded subsurface energy system, whilst mitigating against resource sterilisation and environmental impacts, and could play a role in positively informing public and policy debate. Copyright © 2017 British Geological Survey, a component institute of NERC. Published by Elsevier B.V. All rights reserved.

Adaptive optics for reduced threshold energy in femtosecond laser induced optical breakdown in water based eye model

Science.gov (United States)

Hansen, Anja; Krueger, Alexander; Ripken, Tammo

2013-03-01

In ophthalmic microsurgery tissue dissection is achieved using femtosecond laser pulses to create an optical breakdown. For vitreo-retinal applications the irradiance distribution in the focal volume is distorted by the anterior components of the eye causing a raised threshold energy for breakdown. In this work, an adaptive optics system enables spatial beam shaping for compensation of aberrations and investigation of wave front influence on optical breakdown. An eye model was designed to allow for aberration correction as well as detection of optical breakdown. The eye model consists of an achromatic lens for modeling the eye's refractive power, a water chamber for modeling the tissue properties, and a PTFE sample for modeling the retina's scattering properties. Aberration correction was performed using a deformable mirror in combination with a Hartmann-Shack-sensor. The influence of an adaptive optics aberration correction on the pulse energy required for photodisruption was investigated using transmission measurements for determination of the breakdown threshold and video imaging of the focal region for study of the gas bubble dynamics. The threshold energy is considerably reduced when correcting for the aberrations of the system and the model eye. Also, a raise in irradiance at constant pulse energy was shown for the aberration corrected case. The reduced pulse energy lowers the potential risk of collateral damage which is especially important for retinal safety. This offers new possibilities for vitreo-retinal surgery using femtosecond laser pulses.

Efficient technologies or user behaviour, which is the more important when reducing households' energy consumption?

Energy Technology Data Exchange (ETDEWEB)

Gram-Hanssen, K. [Danish Building Research Institute, Aalborg University, A.C. Meyers Vaenge 15, 2450 Copenhagen (Denmark)

2013-08-15

Much policy effort focuses on energy efficiency of technology, though not only efficiency but also user behaviour is an important factor influencing the amount of consumed energy. This paper explores to what extent energy efficiency of appliances and houses or user behaviour is the more important, both for understanding why some households consume much more energy than others, and when looking for relevant approaches to a future low-carbon society. The paper uses several sources to explore this question, most of them from a Danish context, including results from the researcher's own projects and Danish national statistics. These Danish data are discussed together with international studies. Through the presentation of these different projects and examples, it is shown how user behaviour is at least as important as the efficiency of technology when explaining households' energy consumption in Denmark. In the conclusion, these results are discussed in a broader international perspective and it is concluded that more research in this field is necessary. In relation to energy policy, it is argued that it is not a question of technology efficiency or behaviour, as both have to be included in future policy if energy demand is actually to be reduced. Furthermore, it is also argued that not only individual behaviour is relevant, but also a broader perspective on collectively shared low-carbon practices has to be promoted.

Energy conservation in reheating furnaces by reducing scrap and scale formation; Kuumamuokkauksen energiasaeaestoet romun maeaeraeae ja hilseilyae vaehentaemaellae

Energy Technology Data Exchange (ETDEWEB)

Kivivuori, S.; Savolainen, P.; Fredriksson, J.; Paavola, J. [Helsinki Univ. of Technology, Otaniemi (Finland). Lab. of Materials Processing and Powder Metallurgy

1996-12-31

The main objective of the project `Energy Savings in Reheating Furnaces by Reducing Scrap and Scale Formation` is to reduce energy consumption and environmental harms in reheating and rolling of steel. This was done by analysing the different atmospheres in reheating furnaces of the steel companies participating in this project. These atmospheres were then simulated in a laboratory furnace. Scale formation tests with different steel grades were then carried out in these atmospheres. Scale removal tests were done to some steel grades too. The results showed that lower oxygen content - as expected - decreases oxidation despite the even higher carbondioxide content in the atmosphere. Lower oxygen content may cause difficulties in scale removal. This however is highly dependent on the steel grade. Heat treatment tests showed the effect of increased temperature and furnace time on decarburization. Some energy savings was obtained in fuel consumption by optimising the operation parameters and the atmosphere steadier in different reheating furnaces. (orig.)

Energy conservation in reheating furnaces by reducing scrap and scale formation; Kuumamuokkauksen energiasaeaestoet romun maeaeraeae ja hilseilyae vaehentaemaellae

Energy Technology Data Exchange (ETDEWEB)

Kivivuori, S; Savolainen, P; Fredriksson, J; Paavola, J [Helsinki Univ. of Technology, Otaniemi (Finland). Lab. of Materials Processing and Powder Metallurgy

1997-12-31

The main objective of the project `Energy Savings in Reheating Furnaces by Reducing Scrap and Scale Formation` is to reduce energy consumption and environmental harms in reheating and rolling of steel. This was done by analysing the different atmospheres in reheating furnaces of the steel companies participating in this project. These atmospheres were then simulated in a laboratory furnace. Scale formation tests with different steel grades were then carried out in these atmospheres. Scale removal tests were done to some steel grades too. The results showed that lower oxygen content - as expected - decreases oxidation despite the even higher carbondioxide content in the atmosphere. Lower oxygen content may cause difficulties in scale removal. This however is highly dependent on the steel grade. Heat treatment tests showed the effect of increased temperature and furnace time on decarburization. Some energy savings was obtained in fuel consumption by optimising the operation parameters and the atmosphere steadier in different reheating furnaces. (orig.)

Which energies in 2050?

International Nuclear Information System (INIS)

Lemperiere, F.

2011-01-01

The author analyzes the various possibilities of energy supply which are needed for the world development while significantly reducing the use of fossil energies. He shows that, by 2050, it is possible to double the energy consumption while tripling the world wealth mainly located in emerging or developing countries, and that it is possible to reach a 80 pc share for the renewable energies. The impact of the various scenarios for nuclear power (from a growth of its share to a complete phase-out) is shown to be moderated, even in France

Renewable energy resources

DEFF Research Database (Denmark)

Ellabban, Omar S.; Abu-Rub, Haitham A.; Blaabjerg, Frede

2014-01-01

Electric energy security is essential, yet the high cost and limited sources of fossil fuels, in addition to the need to reduce greenhouse gasses emission, have made renewable resources attractive in world energy-based economies. The potential for renewable energy resources is enormous because...... they can, in principle, exponentially exceed the world's energy demand; therefore, these types of resources will have a significant share in the future global energy portfolio, much of which is now concentrating on advancing their pool of renewable energy resources. Accordingly, this paper presents how...... renewable energy resources are currently being used, scientific developments to improve their use, their future prospects, and their deployment. Additionally, the paper represents the impact of power electronics and smart grid technologies that can enable the proportionate share of renewable energy...

Energy efficiency of batch and semi-batch (CCRO) reverse osmosis desalination.

Science.gov (United States)

Warsinger, David M; Tow, Emily W; Nayar, Kishor G; Maswadeh, Laith A; Lienhard V, John H

2016-12-01

As reverse osmosis (RO) desalination capacity increases worldwide, the need to reduce its specific energy consumption becomes more urgent. In addition to the incremental changes attainable with improved components such as membranes and pumps, more significant reduction of energy consumption can be achieved through time-varying RO processes including semi-batch processes such as closed-circuit reverse osmosis (CCRO) and fully-batch processes that have not yet been commercialized or modelled in detail. In this study, numerical models of the energy consumption of batch RO (BRO), CCRO, and the standard continuous RO process are detailed. Two new energy-efficient configurations of batch RO are analyzed. Batch systems use significantly less energy than continuous RO over a wide range of recovery ratios and source water salinities. Relative to continuous RO, models predict that CCRO and batch RO demonstrate up to 37% and 64% energy savings, respectively, for brackish water desalination at high water recovery. For batch RO and CCRO, the primary reductions in energy use stem from atmospheric pressure brine discharge and reduced streamwise variation in driving pressure. Fully-batch systems further reduce energy consumption by not mixing streams of different concentrations, which CCRO does. These results demonstrate that time-varying processes can significantly raise RO energy efficiency. Copyright © 2016 Elsevier Ltd. All rights reserved.

Interaction between FOXO1A-209 Genotype and Tea Drinking is Significantly Associated with Reduced Mortality at Advanced Ages

DEFF Research Database (Denmark)

Zeng, Yi; Chen, Huashuai; Ni, Ting

2016-01-01

Based on the genotypic/phenotypic data from Chinese Longitudinal Healthy Longevity Survey (CLHLS) and Cox proportional hazard model, the present study demonstrates that interactions between carrying FOXO1A-209 genotypes and tea drinking are significantly associated with lower risk of mortality...... at advanced ages. Such significant association is replicated in two independent Han Chinese CLHLS cohorts (p =0.028-0.048 in the discovery and replication cohorts, and p =0.003-0.016 in the combined dataset). We found the associations between tea drinking and reduced mortality are much stronger among carriers...... of the FOXO1A-209 genotype compared to non-carriers, and drinking tea is associated with a reversal of the negative effects of carrying FOXO1A-209 minor alleles, that is, from a substantially increased mortality risk to substantially reduced mortality risk at advanced ages. The impacts are considerably...

Induction-heating MOCVD reactor with significantly improved heating efficiency and reduced harmful magnetic coupling

KAUST Repository

Li, Kuang-Hui; Alotaibi, Hamad S.; Sun, Haiding; Lin, Ronghui; Guo, Wenzhe; Torres-Castanedo, Carlos G.; Liu, Kaikai; Galan, Sergio V.; Li, Xiaohang

2018-01-01

In a conventional induction-heating III-nitride metalorganic chemical vapor deposition (MOCVD) reactor, the induction coil is outside the chamber. Therefore, the magnetic field does not couple with the susceptor well, leading to compromised heating efficiency and harmful coupling with the gas inlet and thus possible overheating. Hence, the gas inlet has to be at a minimum distance away from the susceptor. Because of the elongated flow path, premature reactions can be more severe, particularly between Al- and B-containing precursors and NH3. Here, we propose a structure that can significantly improve the heating efficiency and allow the gas inlet to be closer to the susceptor. Specifically, the induction coil is designed to surround the vertical cylinder of a T-shaped susceptor comprising the cylinder and a top horizontal plate holding the wafer substrate within the reactor. Therefore, the cylinder coupled most magnetic field to serve as the thermal source for the plate. Furthermore, the plate can block and thus significantly reduce the uncoupled magnetic field above the susceptor, thereby allowing the gas inlet to be closer. The results show approximately 140% and 2.6 times increase in the heating and susceptor coupling efficiencies, respectively, as well as a 90% reduction in the harmful magnetic flux on the gas inlet.

Induction-heating MOCVD reactor with significantly improved heating efficiency and reduced harmful magnetic coupling

KAUST Repository

Li, Kuang-Hui

2018-02-23

In a conventional induction-heating III-nitride metalorganic chemical vapor deposition (MOCVD) reactor, the induction coil is outside the chamber. Therefore, the magnetic field does not couple with the susceptor well, leading to compromised heating efficiency and harmful coupling with the gas inlet and thus possible overheating. Hence, the gas inlet has to be at a minimum distance away from the susceptor. Because of the elongated flow path, premature reactions can be more severe, particularly between Al- and B-containing precursors and NH3. Here, we propose a structure that can significantly improve the heating efficiency and allow the gas inlet to be closer to the susceptor. Specifically, the induction coil is designed to surround the vertical cylinder of a T-shaped susceptor comprising the cylinder and a top horizontal plate holding the wafer substrate within the reactor. Therefore, the cylinder coupled most magnetic field to serve as the thermal source for the plate. Furthermore, the plate can block and thus significantly reduce the uncoupled magnetic field above the susceptor, thereby allowing the gas inlet to be closer. The results show approximately 140% and 2.6 times increase in the heating and susceptor coupling efficiencies, respectively, as well as a 90% reduction in the harmful magnetic flux on the gas inlet.

Risk transfer via energy-savings insurance

International Nuclear Information System (INIS)

Mills, Evan

2003-01-01

Among the key barriers to investment in energy efficiency are uncertainties about attaining projected energy savings and potential disputes over stipulated savings. The fields of energy management and risk management are thus intertwined. While many technical methods have emerged to manage performance risks (e.g. building diagnostics and commissioning), financial methods are less developed in the energy management arena than in other segments of the economy. Energy-savings insurance (ESI) - formal insurance of predicted energy savings - transfers and spreads both types of risk over a larger pool of energy efficiency projects and reduces barriers to market entry of smaller energy service firms who lack sufficiently strong balance sheets to self-insure the savings. ESI encourages those implementing energy-saving projects to go beyond standard measures and thereby achieve more significant levels of energy savings. Insurance providers are proponents of improved savings measurement and verification techniques, as well as maintenance, thereby contributing to national energy-saving objectives. If properly applied, ESI can potentially reduce the net cost of energy-saving projects by reducing the interest rates charged by lenders, and by increasing the level of savings through quality control. Governmental agencies have been pioneers in the use of ESI and could continue to play a role

Creatine supplementation reduces sleep need and homeostatic sleep pressure in rats.

Science.gov (United States)

Dworak, Markus; Kim, Tae; Mccarley, Robert W; Basheer, Radhika

2017-06-01

Sleep has been postulated to promote brain energy restoration. It is as yet unknown if increasing the energy availability within the brain reduces sleep need. The guanidine amino acid creatine (Cr) is a well-known energy booster in cellular energy homeostasis. Oral Cr-monohydrate supplementation (CS) increases exercise performance and has been shown to have substantial effects on cognitive performance, neuroprotection and circadian rhythms. The effect of CS on cellular high-energy molecules and sleep-wake behaviour is unclear. Here, we examined the sleep-wake behaviour and brain energy metabolism before and after 4-week-long oral administration of CS in the rat. CS decreased total sleep time and non-rapid eye movement (NREM) sleep significantly during the light (inactive) but not during the dark (active) period. NREM sleep and NREM delta activity were decreased significantly in CS rats after 6 h of sleep deprivation. Biochemical analysis of brain energy metabolites showed a tendency to increase in phosphocreatine after CS, while cellular adenosine triphosphate (ATP) level decreased. Microdialysis analysis showed that the sleep deprivation-induced increase in extracellular adenosine was attenuated after CS. These results suggest that CS reduces sleep need and homeostatic sleep pressure in rats, thereby indicating its potential in the treatment of sleep-related disorders. © 2017 European Sleep Research Society.

The Determinant of US Consumers Attitudes toward Solar Energy

Science.gov (United States)

Lu, Chao-Lin

2016-01-01

Solar energy provides several significant advantages, such as reduction of the CO[subscript 2] emissions, increase of energy supply diversification, security of energy, and regional/national energy independence. Due to the reduced installation cost and the rapid advances in solar energy technology, the installed capacity of solar power has been…

The location as an energy efficiency and renewable energy supply measure for data centres in Europe

International Nuclear Information System (INIS)

Depoorter, Victor; Oró, Eduard; Salom, Jaume

2015-01-01

Highlights: • A data centre energy model was developed using TRNSYS. • The potential of direct air free cooling integration was evaluated around Europe. • A set of energy indicators describing the operation of data centres were defined. • The location of a data centre could significantly affect its operation and impact. • Smart management of the IT load can reduce energy consumption and CO 2 emission. - Abstract: The massive data centre energy consumption has motivated significant efforts to use energy efficiency strategies and the implementation of renewable energy sources that reduce their operational costs and environmental impact. Considering that the potential of many of these measures is often closely linked to the climate conditions, the location of data centres can have a major impact on their energy demand. Moreover, from a holistic approach, differences among regions become even more important when accounting for the electricity attributes from the grid. To assess these differences this work compares by the use of energy indicators the behaviour of a data centre located at different representative emplacements in Europe. To do so, a dynamic energy model which incorporates free cooling strategy and photovoltaic energy is developed. The paper concludes by suggesting that future data centre developments could consider site selection as a new strategy to limit the environmental impact attributable to this sector

Energymark: Empowering individual Australians to reduce their energy consumption

International Nuclear Information System (INIS)

Dowd, A.; Ashworth, P.; Carr-Cornish, S.; Stenner, K.

2012-01-01

Commitment to increase public awareness of climate change mitigation has risen substantially and so has the appreciation of the impact that comes from voluntary behaviour change. We aimed to test whether a process could be designed that encouraged individuals – from within their existing social networks – to facilitate energy reduction discussions that ultimately changed the way they consumed energy. Our “Energymark” process was grounded in the idea that change is facilitated by several supporting factors including the provision of tailored information, social support, encouragement to set goals, and access to feedback. In this paper we report on the first trial with members of the Australian public. By the end of the trial an average emissions reduction of 20% was reported using a pre- and post-trial carbon calculator incorporating the energy used at home, waste, spending on products and services, beef consumption, and transport. While many identified as climate change aware, and had the socio-economic capacity to make changes, we found that participants of widely varying demographics and dispositions responded to program features, achieving equivalent emissions reductions. This bodes well for the program’s effectiveness and warrants further testing of the impact of voluntary action with social processes such as Energymark. - Highlights: ► Energymark program recognises the importance of voluntary individual behaviour change. ► Key features include the provision of information, social support, goal setting and access to feedback. ► At the end of the process an average individual emissions reduction of 20% was reported. ► Consequential aspects were gaining awareness and information and developing a sense of social responsibility. ► Significant also was participants’ understanding that government has a role to play in mitigation.

Controlled cooling of an electronic system for reduced energy consumption

Science.gov (United States)

David, Milnes P.; Iyengar, Madhusudan K.; Schmidt, Roger R.

2016-08-09

Energy efficient control of a cooling system cooling an electronic system is provided. The control includes automatically determining at least one adjusted control setting for at least one adjustable cooling component of a cooling system cooling the electronic system. The automatically determining is based, at least in part, on power being consumed by the cooling system and temperature of a heat sink to which heat extracted by the cooling system is rejected. The automatically determining operates to reduce power consumption of the cooling system and/or the electronic system while ensuring that at least one targeted temperature associated with the cooling system or the electronic system is within a desired range. The automatically determining may be based, at least in part, on one or more experimentally obtained models relating the targeted temperature and power consumption of the one or more adjustable cooling components of the cooling system.

Mass independent kinetic energy reducing inlet system for vacuum environment

Science.gov (United States)

Reilly, Peter T. A. [Knoxville, TN

2010-12-14

A particle inlet system comprises a first chamber having a limiting orifice for an incoming gas stream and a micrometer controlled expansion slit. Lateral components of the momentum of the particles are substantially cancelled due to symmetry of the configuration once the laminar flow converges at the expansion slit. The particles and flow into a second chamber, which is maintained at a lower pressure than the first chamber, and then moves into a third chamber including multipole guides for electromagnetically confining the particle. The vertical momentum of the particles descending through the center of the third chamber is minimized as an upward stream of gases reduces the downward momentum of the particles. The translational kinetic energy of the particles is near-zero irrespective of the mass of the particles at an exit opening of the third chamber, which may be advantageously employed to provide enhanced mass resolution in mass spectrometry.

Controlled cooling of an electronic system for reduced energy consumption

Energy Technology Data Exchange (ETDEWEB)

David, Milnes P.; Iyengar, Madhusudan K.; Schmidt, Roger R.

2018-01-30

Energy efficient control of a cooling system cooling an electronic system is provided. The control includes automatically determining at least one adjusted control setting for at least one adjustable cooling component of a cooling system cooling the electronic system. The automatically determining is based, at least in part, on power being consumed by the cooling system and temperature of a heat sink to which heat extracted by the cooling system is rejected. The automatically determining operates to reduce power consumption of the cooling system and/or the electronic system while ensuring that at least one targeted temperature associated with the cooling system or the electronic system is within a desired range. The automatically determining may be based, at least in part, on one or more experimentally obtained models relating the targeted temperature and power consumption of the one or more adjustable cooling components of the cooling system.

Power Loss Analysis and Comparison of Segmented and Unsegmented Energy Coupling Coils for Wireless Energy Transfer.

Science.gov (United States)

Tang, Sai Chun; McDannold, Nathan J

2015-03-01

This paper investigated the power losses of unsegmented and segmented energy coupling coils for wireless energy transfer. Four 30-cm energy coupling coils with different winding separations, conductor cross-sectional areas, and number of turns were developed. The four coils were tested in both unsegmented and segmented configurations. The winding conduction and intrawinding dielectric losses of the coils were evaluated individually based on a well-established lumped circuit model. We found that the intrawinding dielectric loss can be as much as seven times higher than the winding conduction loss at 6.78 MHz when the unsegmented coil is tightly wound. The dielectric loss of an unsegmented coil can be reduced by increasing the winding separation or reducing the number of turns, but the power transfer capability is reduced because of the reduced magnetomotive force. Coil segmentation using resonant capacitors has recently been proposed to significantly reduce the operating voltage of a coil to a safe level in wireless energy transfer for medical implants. Here, we found that it can naturally eliminate the dielectric loss. The coil segmentation method and the power loss analysis used in this paper could be applied to the transmitting, receiving, and resonant coils in two- and four-coil energy transfer systems.

A Recombinant Multi-Stage Vaccine against Paratuberculosis Significantly Reduces Bacterial Level in Tissues without Interference in Diagnostics

DEFF Research Database (Denmark)

Jungersen, Gregers; Thakur, Aneesh; Aagaard, C.

, PPDj-specific IFN-γ responses or positive PPDa or PPDb skin tests developed in vaccinees. Antibodies and cell-mediated immune responses were developed against FET11 antigens, however. At necropsy 8 or 12 months of age, relative Map burden was determined in a number of gut tissues by quantitative IS900...... PCR and revealed significantly reduced levels of Map and reduced histopathology. Diagnostic tests for antibody responses and cell-mediated immune responses, used as surrogates of infection, corroborated the observed vaccine efficacy: Five of seven non‐vaccinated calves seroconverted in ID Screen......-γ assay responses from 40 to 52 weeks compared to non-vaccinated calves. These results indicate the FET11 vaccine can be used to accelerate eradication of paratuberculosis while surveillance or test-and-manage control programs for tuberculosis and Johne’s disease remain in place. Funded by EMIDA ERA...

Energy savings through self-backhauling for future heterogeneous networks

International Nuclear Information System (INIS)

Faruk, Nasir; Ruttik, Kalle; Mutafungwa, Edward; Jäntti, Riku

2016-01-01

Mobile operators face continuous challenge of enhancing network capacity and coverage so as to meet demand for ubiquitous high-speed mobile data connectivity. Unfortunately, these enhancements are typically accompanied by increased burden of network energy consumption. Heterogeneous network (HetNet) deployments of a large number of low power small base stations (SBS) to complement existing macro base stations is an approach that increases network capacity but potentially reduces overall network energy consumption. The SBS backhaul links in HetNets present a significant powering burden. In this paper, we show how self backhauling of SBS can reduce overall network power demand. A backhaul-energy consumption model is developed and used to investigate the energy efficiency of different backhauling options. We note that significant energy savings could be achieved through the use of self-backhauling when compared with the conventional microwave backhauling. The results presented would provide guidelines for energy- and cost-efficient backhaul implementation for future HetNets. - Highlights: • A backhaul-energy consumption model is developed. • Self backhauling of small base stations can reduce overall network power demand. • Energy saving strategy presented would relieved the burden on the power networks. • Results provide guidelines for energy and cost effective backhaul implementation.

Energy Storage Annual Progress Report for FY15

Energy Technology Data Exchange (ETDEWEB)

Pesaran, Ahmad [National Renewable Energy Lab. (NREL), Golden, CO (United States); Ban, Chunmei [National Renewable Energy Lab. (NREL), Golden, CO (United States); Cao, Lei [National Renewable Energy Lab. (NREL), Golden, CO (United States); Graf, Peter [National Renewable Energy Lab. (NREL), Golden, CO (United States); Keyser, Matt [National Renewable Energy Lab. (NREL), Golden, CO (United States); Kim, Gi-Heon [National Renewable Energy Lab. (NREL), Golden, CO (United States); Santhanagopalan, Shriram [National Renewable Energy Lab. (NREL), Golden, CO (United States); Saxon, Aron [National Renewable Energy Lab. (NREL), Golden, CO (United States); Shi, Ying [National Renewable Energy Lab. (NREL), Golden, CO (United States); Smith, Kandler [National Renewable Energy Lab. (NREL), Golden, CO (United States); Tenent, Robert [National Renewable Energy Lab. (NREL), Golden, CO (United States); Yang, Chuanbo [National Renewable Energy Lab. (NREL), Golden, CO (United States); Zhang, Chao [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2016-12-01

The Energy Storage research and development (R&D) subprogram within the DOE Vehicle Technologies Office (VTO) provides support and guidance for projects focusing on batteries for plug-in electric vehicles (PEVs) in support of the EV Everywhere Grand Challenge. PEVs could have a significant impact on the nation's goal of reducing dependence on imported oil and gaseous pollutant emissions. The Energy Storage program targets overcoming technical barriers to enable market success, including: (1) significantly reducing battery cost; (2) increasing battery performance (power, energy, durability); (3) reducing battery weight and volume; and (4) increasing battery tolerance to abusive conditions such as short circuit, overcharge, and crush. The National Renewable Energy Laboratory (NREL) supports the VTO's Energy Storage program by evaluating the thermal performance of cells and packs, developing electrochemical-thermal models to accelerate the design cycle for developing batteries, investigating the behavior of lithium-ion batteries under abuse conditions such as crush, enhancing the durability of electrodes by coatings such as atomic layer deposition, synthesis of materials for higher energy density batteries, and conducting techno-economic analysis of batteries in various electric-drive vehicles. This report describes the progress made by NREL on the research and development projects funded by the DOE VTO Energy Storage subprogram in FY15.

Energy efficient data sorting using standard sorting algorithms

KAUST Repository

Bunse, Christian; Hö pfner, Hagen; Roychoudhury, Suman; Mansour, Essam

2011-01-01

Protecting the environment by saving energy and thus reducing carbon dioxide emissions is one of todays hottest and most challenging topics. Although the perspective for reducing energy consumption, from ecological and business perspectives is clear, from a technological point of view, the realization especially for mobile systems still falls behind expectations. Novel strategies that allow (software) systems to dynamically adapt themselves at runtime can be effectively used to reduce energy consumption. This paper presents a case study that examines the impact of using an energy management component that dynamically selects and applies the "optimal" sorting algorithm, from an energy perspective, during multi-party mobile communication. Interestingly, the results indicate that algorithmic performance is not key and that dynamically switching algorithms at runtime does have a significant impact on energy consumption. © Springer-Verlag Berlin Heidelberg 2011.

BUILT ENVIRONMENT: RELATING THE BENEFITS OF RENEWABLE ENERGY TECHNOLOGIES

Directory of Open Access Journals (Sweden)

Abdeen Mustafa Omer

2012-06-01

Full Text Available Recently, environmental issues have been the focus of much of the world’s attention. This has stimulated a response in many countries, which has led to a closer examination of energy conservation strategies for conventional fossil fuels. One way of reducing building energy consumption is to design buildings, which are more economical in their use of energy for: heating, lighting, cooling, ventilation and hot water supply. Passive measures, particularly natural or hybrid ventilation rather than air-conditioning, can dramatically reduce primary energy consumption. However, exploitation of renewable energy in buildings and agricultural greenhouses, can significantly contribute in reducing dependency on fossil fuels. Therefore, promoting innovative renewable applications and reinforcing the renewable energy market will contribute to preserving the ecosystem by reducing emissions at local and global levels. This will also contribute to the amelioration of environmental conditions, through a reduction in air pollution and greenhouse gases, by the replacement of conventional fuels with renewable energies.

Walking on a moving surface: energy-optimal walking motions on a shaky bridge and a shaking treadmill can reduce energy costs below normal.

Science.gov (United States)

Joshi, Varun; Srinivasan, Manoj

2015-02-08

Understanding how humans walk on a surface that can move might provide insights into, for instance, whether walking humans prioritize energy use or stability. Here, motivated by the famous human-driven oscillations observed in the London Millennium Bridge, we introduce a minimal mathematical model of a biped, walking on a platform (bridge or treadmill) capable of lateral movement. This biped model consists of a point-mass upper body with legs that can exert force and perform mechanical work on the upper body. Using numerical optimization, we obtain energy-optimal walking motions for this biped, deriving the periodic body and platform motions that minimize a simple metabolic energy cost. When the platform has an externally imposed sinusoidal displacement of appropriate frequency and amplitude, we predict that body motion entrained to platform motion consumes less energy than walking on a fixed surface. When the platform has finite inertia, a mass- spring-damper with similar parameters to the Millennium Bridge, we show that the optimal biped walking motion sustains a large lateral platform oscillation when sufficiently many people walk on the bridge. Here, the biped model reduces walking metabolic cost by storing and recovering energy from the platform, demonstrating energy benefits for two features observed for walking on the Millennium Bridge: crowd synchrony and large lateral oscillations.

Relative significance of heat transfer processes to quantify tradeoffs between complexity and accuracy of energy simulations with a building energy use patterns classification

Science.gov (United States)

Heidarinejad, Mohammad

This dissertation develops rapid and accurate building energy simulations based on a building classification that identifies and focuses modeling efforts on most significant heat transfer processes. The building classification identifies energy use patterns and their contributing parameters for a portfolio of buildings. The dissertation hypothesis is "Building classification can provide minimal required inputs for rapid and accurate energy simulations for a large number of buildings". The critical literature review indicated there is lack of studies to (1) Consider synoptic point of view rather than the case study approach, (2) Analyze influence of different granularities of energy use, (3) Identify key variables based on the heat transfer processes, and (4) Automate the procedure to quantify model complexity with accuracy. Therefore, three dissertation objectives are designed to test out the dissertation hypothesis: (1) Develop different classes of buildings based on their energy use patterns, (2) Develop different building energy simulation approaches for the identified classes of buildings to quantify tradeoffs between model accuracy and complexity, (3) Demonstrate building simulation approaches for case studies. Penn State's and Harvard's campus buildings as well as high performance LEED NC office buildings are test beds for this study to develop different classes of buildings. The campus buildings include detailed chilled water, electricity, and steam data, enabling to classify buildings into externally-load, internally-load, or mixed-load dominated. The energy use of the internally-load buildings is primarily a function of the internal loads and their schedules. Externally-load dominated buildings tend to have an energy use pattern that is a function of building construction materials and outdoor weather conditions. However, most of the commercial medium-sized office buildings have a mixed-load pattern, meaning the HVAC system and operation schedule dictate

Significant Association between Sulfate-Reducing Bacteria and Uranium-Reducing Microbial Communities as Revealed by a Combined Massively Parallel Sequencing-Indicator Species Approach▿ †

Science.gov (United States)

Cardenas, Erick; Wu, Wei-Min; Leigh, Mary Beth; Carley, Jack; Carroll, Sue; Gentry, Terry; Luo, Jian; Watson, David; Gu, Baohua; Ginder-Vogel, Matthew; Kitanidis, Peter K.; Jardine, Philip M.; Zhou, Jizhong; Criddle, Craig S.; Marsh, Terence L.; Tiedje, James M.

2010-01-01

Massively parallel sequencing has provided a more affordable and high-throughput method to study microbial communities, although it has mostly been used in an exploratory fashion. We combined pyrosequencing with a strict indicator species statistical analysis to test if bacteria specifically responded to ethanol injection that successfully promoted dissimilatory uranium(VI) reduction in the subsurface of a uranium contamination plume at the Oak Ridge Field Research Center in Tennessee. Remediation was achieved with a hydraulic flow control consisting of an inner loop, where ethanol was injected, and an outer loop for flow-field protection. This strategy reduced uranium concentrations in groundwater to levels below 0.126 μM and created geochemical gradients in electron donors from the inner-loop injection well toward the outer loop and downgradient flow path. Our analysis with 15 sediment samples from the entire test area found significant indicator species that showed a high degree of adaptation to the three different hydrochemical-created conditions. Castellaniella and Rhodanobacter characterized areas with low pH, heavy metals, and low bioactivity, while sulfate-, Fe(III)-, and U(VI)-reducing bacteria (Desulfovibrio, Anaeromyxobacter, and Desulfosporosinus) were indicators of areas where U(VI) reduction occurred. The abundance of these bacteria, as well as the Fe(III) and U(VI) reducer Geobacter, correlated with the hydraulic connectivity to the substrate injection site, suggesting that the selected populations were a direct response to electron donor addition by the groundwater flow path. A false-discovery-rate approach was implemented to discard false-positive results by chance, given the large amount of data compared. PMID:20729318

Performance Evaluation of Lower-Energy Energy Storage Alternatives for Full-Hybrid Vehicles; NREL (National Renewable Energy Laboratory)

Energy Technology Data Exchange (ETDEWEB)

Gonder, J.; Cosgrove, J.; Pesaran, A.

2014-02-11

Automakers have been mass producing hybrid electric vehicles (HEVs) for well over a decade, and the technology has proven to be very effective at reducing per-vehicle fuel use. However, the incremental cost of HEVs such as the Toyota Prius or Ford Fusion Hybrid remains several thousand dollars higher than the cost of comparable conventional vehicles, which has limited HEV market penetration. The b b b b battery energy storage device is typically the component with the greatest contribution toward this cost increment, so significant cost reductions/performance improvements to the energy storage system (ESS) can correspondingly improve the vehicle-level cost/benefit relationship. Such an improvement would in turn lead to larger HEV market penetration and greater aggregate fuel savings. The United States Advanced Battery Consortium (USABC) and the U.S. Department of Energy (DOE) Energy Storage Program managers asked the National Renewable Energy Laboratory (NREL) to collaborate with a USABC Workgroup and analyze the trade-offs between vehicle fuel economy and reducing the decade-old minimum energy requirement for power-assist HEVs. NREL’s analysis showed that significant fuel savings could still be delivered from an ESS with much lower energy storage than the previous targets, which prompted USABC to issue a new set of lower-energy ESS (LEESS) targets that could be satisfied by a variety of technologies. With support from DOE, NREL has developed an HEV test platform for in-vehicle performance and fuel economy validation testing of the hybrid system using such LEESS devices. This presentation describes development of the vehicle test platform, and laboratory as well as in-vehicle evaluation results with alternate energy storage configurations as compared to the production battery system. The alternate energy storage technologies considered include lithium-ion capacitors -- i.e., asymmetric electrochemical energy storage devices possessing one electrode with battery

Implementation of standardized follow-up care significantly reduces peritonitis in children on chronic peritoneal dialysis.

Science.gov (United States)

Neu, Alicia M; Richardson, Troy; Lawlor, John; Stuart, Jayne; Newland, Jason; McAfee, Nancy; Warady, Bradley A

2016-06-01

The Standardizing Care to improve Outcomes in Pediatric End stage renal disease (SCOPE) Collaborative aims to reduce peritonitis rates in pediatric chronic peritoneal dialysis patients by increasing implementation of standardized care practices. To assess this, monthly care bundle compliance and annualized monthly peritonitis rates were evaluated from 24 SCOPE centers that were participating at collaborative launch and that provided peritonitis rates for the 13 months prior to launch. Changes in bundle compliance were assessed using either a logistic regression model or a generalized linear mixed model. Changes in average annualized peritonitis rates over time were illustrated using the latter model. In the first 36 months of the collaborative, 644 patients with 7977 follow-up encounters were included. The likelihood of compliance with follow-up care practices increased significantly (odds ratio 1.15, 95% confidence interval 1.10, 1.19). Mean monthly peritonitis rates significantly decreased from 0.63 episodes per patient year (95% confidence interval 0.43, 0.92) prelaunch to 0.42 (95% confidence interval 0.31, 0.57) at 36 months postlaunch. A sensitivity analysis confirmed that as mean follow-up compliance increased, peritonitis rates decreased, reaching statistical significance at 80% at which point the prelaunch rate was 42% higher than the rate in the months following achievement of 80% compliance. In its first 3 years, the SCOPE Collaborative has increased the implementation of standardized follow-up care and demonstrated a significant reduction in average monthly peritonitis rates. Copyright © 2016 International Society of Nephrology. Published by Elsevier Inc. All rights reserved.

Energy Expenditure and Physical Activity in Prader–Willi Syndrome

Science.gov (United States)

Butler, Merlin G.; Theodoro, Mariana F.; Bittel, Douglas C.; Donnelly, Joseph E.

2017-01-01

Prader–Willi syndrome (PWS) is a complex neurodevelopmental disorder characterized by hypotonia, suck and feeding difficulties, hypogonadism, small hands and feet, developmental delay, hyperphagia and early childhood obesity and a particular facial appearance. The obesity associated with PWS is the result of a chronic imbalance between energy intake and energy expenditure (EE) due to hyperphagia, decreased physical activity, reduced metabolic rate and an inability to vomit. EE is affected by body composition as well as exercise. Individuals with PWS have a lower lean body mass (LBM) compared with controls which may contribute to reduced basal level EE. To determine the relationship among body composition, activity levels and metabolic rates, dual energy X-ray absorptiometry (DEXA) and a whole-room respiration chamber were used to measure body composition, total EE (TEE), resting EE (REE), physical activity, and mechanical work (MW) during an 8 hr monitoring period. The chamber consisted of a live-in whole-room indirect calorimeter equipped with a force platform floor to allow simultaneous measurement of EE, physical activity, and work efficiency during spontaneous activities and standardized exercise. Participants with PWS (27 with 15q11–q13 deletion and 21 with maternal disomy 15 with an average age of 23 years) had significantly decreased TEE by 20% and reduced LBM compared to 24 obese subjects. Similarly, REE was significantly reduced by 16% in the individuals with PWS relative to the comparison subjects. Total MW performed during the 8 hr monitoring period was significantly reduced by 35% in the PWS group. The energy cost of physical activity is related to the duration, intensity and type of activity and the metabolic efficiency of the individual. After adjusting group differences in LBM by analysis of variance, TEE and REE were no longer different between the two groups. Our data indicate that there is a significant reduction of EE in individuals with PWS

Reducing CO2 emissions in Sierra Leone and Ghana

International Nuclear Information System (INIS)

Davidson, O.

1991-01-01

With soring population growth rates and minimal economic growth, the nations of Africa are afflicted with innumerable problems. Why then should Africa's developing countries worry about CO 2 emissions? First, because agricultural activities form the backbone of most African economies; thus, these nations may be particularly vulnerable to the negative impacts of climate change. Second, acting to reduce carbon emissions will bring about more efficient energy use. All of Africa could benefit from the improved use of energy. Finally, the accumulation of CO 2 in the atmosphere is a global problem with individual solutions; in order to reduce international emissions, all countries, including those in Africa, must contribute. Typical of many African countries, Ghana and Sierra Leone have among the lowest levels of energy demand per capita across the globe. primary energy demand per capita in these two West African nations equals about one quarter of the world's average and about one twentieth of the US average. This work summarizes the results of two long-term energy use and carbon emissions scenarios for Sierra Leone and Ghana. In the high emissions (HE) scenario for 2025, policy changes focused on galvanizing economic growth lead to significant increases in energy use and carbon emissions in Ghana and Sierra Leone between 1985 and 2025. In the low emissions (LE) scenario, the implementation of policies aimed specifically at curtailing CO 2 emissions significantly limits the increase in carbon in both nations by 2025

Reducing TV watching during adult obesity treatment: two pilot randomized controlled trials.

Science.gov (United States)

Raynor, Hollie A; Steeves, Elizabeth Anderson; Bassett, David R; Thompson, Dixie L; Gorin, Amy A; Bond, Dale S

2013-12-01

The more time adults spend being sedentary, the greater the risk of obesity. The effect of reducing television (TV) watching, a prominent sedentary behavior, on weight loss has not been tested in an adult standard behavioral obesity intervention, and the mechanisms by which reducing TV watching influences energy balance behaviors are not well understood. Two, 8-week, pilot, randomized controlled trials were conducted examining the effect of a reduced TV watching prescription on energy balance behaviors and weight loss within an adult standard behavioral obesity intervention. In the first study, participants (n=24) were randomized into one of two conditions: (a) reduce energy intake and increase moderate to vigorous physical activity (MVPA) (INCREASE PA); or (b) reduce energy intake and decrease TV watching (DECREASE TV). As findings from the first pilot study did not show an increase in MVPA in the DECREASE TV group, the second study was designed to examine the effect of adding a reduced TV prescription to a standard intervention to optimize outcomes. In Pilot Study 2, participants (n=28) were randomized to INCREASE PA or to INCREASE PA+DECREASE TV. Outcomes included objectively measured TV watching and MVPA, self-reported light physical activity (LPA-Pilot Study 2 only), self-reported dietary intake while watching TV, and weight. Conditions with TV watching prescriptions significantly reduced TV watching. Both studies showed medium to large effect sizes for conditions with TV watching prescriptions to show greater reductions in dietary intake while watching TV. Pilot Study 1 found a trend for an increase in MVPA in INCREASE PA and Pilot Study 2 found significant increases in MVPA in both conditions. Pilot Study 2 found a significant increase in LPA in the INCREASE PA+DECREASE TV. Results indicate adding a TV watching prescription to a standard obesity intervention did not enhance increases in MVPA, but may assist with reducing dietary intake while TV watching and

Reduced energy offset via substitutional doping for efficient organic/inorganic hybrid solar cells.

Science.gov (United States)

Jin, Xiao; Sun, Weifu; Zhang, Qin; Ruan, Kelian; Cheng, Yuanyuan; Xu, Haijiao; Xu, Zhongyuan; Li, Qinghua

2015-06-01

Charge carrier transport in bulk heterojunction that is central to the device performance of solar cells is sensitively dependent on the energy level alignment of acceptor and donor. However, the effect of energy level regulation induced by nickel ions on the primary photoexcited electron transfer and the performance of P3HT/TiO2 hybrid solar cells remains being poorly understood and rarely studied. Here we demonstrate that the introduction of the versatile nickel ions into TiO2 nanocrystals can significantly elevate the conduction and valence band energy levels of the acceptor, thus resulting in a remarkable reduction of energy level offset between the conduction band of acceptor and lowest unoccupied molecular orbital of donor. By applying transient photoluminescence and femtosecond transient absorption spectroscopies, we demonstrate that the electron transfer becomes more competitive after incorporating nickel ions. In particular, the electron transfer life time is shortened from 30.2 to 16.7 ps, i.e., more than 44% faster than pure TiO2 acceptor, thus leading to a notable increase of power conversion efficiency in organic/inorganic hybrid solar cells. This work underscores the promising virtue of engineering the reduction of 'excess' energy offset to accelerate electron transport and demonstrates the potential of nickel ions in applications of solar energy conversion and photon detectors.

Quasi-particle energy spectra in local reduced density matrix functional theory.

Science.gov (United States)

Lathiotakis, Nektarios N; Helbig, Nicole; Rubio, Angel; Gidopoulos, Nikitas I

2014-10-28

Recently, we introduced [N. N. Lathiotakis, N. Helbig, A. Rubio, and N. I. Gidopoulos, Phys. Rev. A 90, 032511 (2014)] local reduced density matrix functional theory (local RDMFT), a theoretical scheme capable of incorporating static correlation effects in Kohn-Sham equations. Here, we apply local RDMFT to molecular systems of relatively large size, as a demonstration of its computational efficiency and its accuracy in predicting single-electron properties from the eigenvalue spectrum of the single-particle Hamiltonian with a local effective potential. We present encouraging results on the photoelectron spectrum of molecular systems and the relative stability of C20 isotopes. In addition, we propose a modelling of the fractional occupancies as functions of the orbital energies that further improves the efficiency of the method useful in applications to large systems and solids.

Simulation and energy analysis of distributed electric heating system

Science.gov (United States)

Yu, Bo; Han, Shenchao; Yang, Yanchun; Liu, Mingyuan

2018-02-01

Distributed electric heating system assistssolar heating systemby using air-source heat pump. Air-source heat pump as auxiliary heat sourcecan make up the defects of the conventional solar thermal system can provide a 24 - hour high - efficiency work. It has certain practical value and practical significance to reduce emissions and promote building energy efficiency. Using Polysun software the system is simulated and compared with ordinary electric boiler heating system. The simulation results show that upon energy request, 5844.5kW energy is saved and 3135kg carbon - dioxide emissions are reduced and5844.5 kWhfuel and energy consumption is decreased with distributed electric heating system. Theeffect of conserving energy and reducing emissions using distributed electric heating systemis very obvious.

Optimal urban water conservation strategies considering embedded energy: coupling end-use and utility water-energy models.

Science.gov (United States)

Escriva-Bou, A.; Lund, J. R.; Pulido-Velazquez, M.; Spang, E. S.; Loge, F. J.

2014-12-01

Although most freshwater resources are used in agriculture, a greater amount of energy is consumed per unit of water supply for urban areas. Therefore, efforts to reduce the carbon footprint of water in cities, including the energy embedded within household uses, can be an order of magnitude larger than for other water uses. This characteristic of urban water systems creates a promising opportunity to reduce global greenhouse gas emissions, particularly given rapidly growing urbanization worldwide. Based on a previous Water-Energy-CO2 emissions model for household water end uses, this research introduces a probabilistic two-stage optimization model considering technical and behavioral decision variables to obtain the most economical strategies to minimize household water and water-related energy bills given both water and energy price shocks. Results show that adoption rates to reduce energy intensive appliances increase significantly, resulting in an overall 20% growth in indoor water conservation if household dwellers include the energy cost of their water use. To analyze the consequences on a utility-scale, we develop an hourly water-energy model based on data from East Bay Municipal Utility District in California, including the residential consumption, obtaining that water end uses accounts for roughly 90% of total water-related energy, but the 10% that is managed by the utility is worth over 12 million annually. Once the entire end-use + utility model is completed, several demand-side management conservation strategies were simulated for the city of San Ramon. In this smaller water district, roughly 5% of total EBMUD water use, we found that the optimal household strategies can reduce total GHG emissions by 4% and utility's energy cost over 70,000/yr. Especially interesting from the utility perspective could be the "smoothing" of water use peaks by avoiding daytime irrigation that among other benefits might reduce utility energy costs by 0.5% according to our

Do food provisions packaged in single-servings reduce energy intake at breakfast during a brief behavioral weight-loss intervention?

Science.gov (United States)

Raynor, Hollie A; Van Walleghen, Emily L; Niemeier, Heather; Butryn, Meghan L; Wing, Rena R

2009-11-01

Larger portion sizes increase energy intake, yet it is unclear whether single-serving packages can reduce intake. This study examined the effects of providing breakfast foods in single-serving packages and nonportioned packages on energy intake of these foods during an 8-week behavioral weight-loss program. In fall 2005, 19 adults (mean body mass index [calculated as kg/m(2)]=31.8+/-4.0) were randomized to conditions that provided foods in single-serving packages (Single-Serving) or in nonportioned packages (Standard). Overall amounts and types of foods provided were consistent across conditions: cereal and peaches (weeks 1, 3, 5, and 7) and applesauce and cheese (weeks 2, 4, 6, and 8). Participants were instructed to eat one serving of each food for breakfast and not to consume the provided foods at other times. Mean daily energy intake of the provided foods was the primary dependent variable. The Single-Serving group ate less energy from the combined pairs of foods provided together as compared to Standard (cereal and peaches, 117.0+/-3.2 kcal/day vs 143.5+/-39.3 kcal/day; P0.10). This suggests that single-serving packages may help reduce energy intake at breakfast within the context of a behavioral weight-control program.

Binge abstinence is associated with reduced energy intake after treatment in patients with binge eating disorder and obesity.

Science.gov (United States)

Masheb, Robin M; Dorflinger, Lindsey M; Rolls, Barbara J; Mitchell, Diane C; Grilo, Carlos M

2016-12-01

Binge eating disorder (BED) is strongly associated with obesity and related medical and psychiatric morbidities. Cognitive behavioral therapy (CBT) has consistently been shown to reduce binge eating frequency and improve psychological functioning, as well as to produce abstinence rates of roughly 50%. This study examined the relationship between binge abstinence and dietary and psychological outcomes after CBT for BED. Fifty adult patients with BED received 6-month treatments using a combination of CBT and dietary counseling. Trained interviewers conducted two 24-hour dietary recall interviews on randomly selected days at baseline and at 6 months. Participants had significant reductions in energy, macronutrient, and sugar intake and an increase in fruit intake. They reported significant reductions in BMI and binge eating frequency (from mean = 14.24 to mean = 1.90 binge eating episodes during the previous 28 days), as well as improvements in psychological functioning. Those who became binge abstinent reported eating roughly 400 fewer calories per day and experienced greater improvements in psychological functioning than those who did not. Findings from this study suggest that individuals who achieve complete cessation from binge eating have significantly improved dietary and psychological outcomes that could potentially improve weight status, compared with those who continue to binge eat post-treatment. © 2016 The Obesity Society.

Energy Efficiency and Renewable Energy Research, Development, and Deployment in Meeting Greenhouse Gas Mitigation Goals. The Case of the Lieberman-Warner Climate Security Act of 2007 (S. 2191)

Energy Technology Data Exchange (ETDEWEB)

Showalter, Sharon [OnLocation, Inc./ Energy Systems Consulting, Vienna, VA (United States); Wood, Frances [OnLocation, Inc./ Energy Systems Consulting, Vienna, VA (United States); Vimmerstedt, Laura [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2010-06-01

The U.S. federal government is considering actions to reduce greenhouse gas emissions. Renewable energy and energy efficiency technologies could help reduce greenhouse gas emissions, so the cost of these technologies could significantly influence the overall cost of meeting greenhouse gas limits. This paper examines the potential benefit of reduced technology cost by analyzing the case of the Lieberman-Warner Climate Security Act of 2007 (S.2191). This act had a goal of reducing national carbon emissions in 2050 to levels 72 percent below 2006 emission levels. In April 2008, the U.S. Department of Energy, Energy Information Administration (EIA) published an analysis of the effects of S.2191 on the U.S. energy sector. This report presents a similar analysis: both analyses examined the impacts of S.2191, and both used versions of the National Energy Modeling System. The analysis reported here used modified technology assumptions to reflect U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy (EERE) program goals. The results show that achieving EERE program goals could reduce the cost of meeting greenhouse gas limits, reduce the cost of renewable electricity generation and biofuels, and reduce energy intensity.

Energy Efficiency and Renewable Energy Research, Development, and Deployment in Meeting Greenhouse Gas Mitigation Goals: The Case of the Lieberman-Warner Climate Security Act of 2007 (S.2191)

Energy Technology Data Exchange (ETDEWEB)

Showalter, S.; Wood, F.; Vimmerstedt, L.

2010-06-01

The U.S. federal government is considering actions to reduce greenhouse gas emissions. Renewable energy and energy efficiency technologies could help reduce greenhouse gas emissions, so the cost of these technologies could significantly influence the overall cost of meeting greenhouse gas limits. This paper examines the potential benefit of reduced technology cost by analyzing the case of the Lieberman-Warner Climate Security Act of 2007 (S.2191). This act had a goal of reducing national carbon emissions in 2050 to levels 72 percent below 2006 emission levels. In April 2008, the U.S. Department of Energy, Energy Information Administration (EIA) published an analysis of the effects of S.2191 on the U.S. energy sector. This report presents a similar analysis: both analyses examined the impacts of S.2191, and both used versions of the National Energy Modeling System. The analysis reported here used modified technology assumptions to reflect U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy (EERE) program goals. The results show that achieving EERE program goals could reduce the cost of meeting greenhouse gas limits, reduce the cost of renewable electricity generation and biofuels, and reduce energy intensity.

Reducing LTE Uplink Transmission Energy by Allocating Resources

DEFF Research Database (Denmark)

Lauridsen, Mads; Jensen, Anders Riis; Mogensen, Preben

2011-01-01

The effect of physical resource block (PRB) allocation on an LTE modem's transmit power and total modem energy consumption is examined. In this paper the uplink resource blocks are scheduled in either a Frequency Division Multiple Access (FDMA) or Time Division Multiple Access (TDMA) manner......, to determine if low transmission power & long transmission time or high transmission power & short transmission time is most energy efficient. It is important to minimize the LTE modem's energy consumption caused by uplink transmission because it affects phone battery time, and because researchers rarely focus...

An experimental investigation on reduced radiological penumbra for intermediate energy x-rays: Implications for small field radiosurgery

Science.gov (United States)

Keller, Brian Michael

Current day external beam radiation therapy typically uses x-ray energies in the megavoltage (6--18 MV) or in the superficial/orthovoltage (80--350 kVp) energy ranges. It has been found that intermediate energy x-rays (those greater than orthovoltage but sub-megavoltage) may offer an advantage in the field of high precision radiation therapy such as in radiosurgery. This advantage is a reduction in the radiological penumbra associated with small (less than about 3 cm) radiation dose fields. A consequence of reduced radiological penumbra is a more homogenous, conformal dose distribution in the patient with dose escalation and organ sparing made more feasible. The objectives of this thesis were as follows: to produce and to characterize an intermediate energy x-ray beam, to establish a method of accurate penumbra measurement at the micron level for millimeter size fields, to measure the radiological penumbra of single small intermediate energy x-ray fields, and to show the clinical consequences of a multiple beam irradiation in a stereotactic head phantom. A maximum photon energy of 1.2 +/- 0.1 MeV was determined for the intermediate energy x-ray spectrum at the expense of a low dose rate. A digital microscope with a computer controlled translation stage was investigated for its ability to resolve steep dose gradients in Gafchromic EBT film for field sizes as small as 1 mm and for photon energies as low as 100 kVp. The microscope-film system resolved gradients to within about 30 mum, limited by the inherent spatial resolution of the film, the noise of the system, and the uncertainties of measurement. Penumbra widths were compared for 1.2 MV versus 6 MV for identical irradiation conditions. In some instances, there was a five-fold reduction in the radiological penumbra of single 1.2 MV x-ray beams. A multiple beam arc irradiation demonstrated that the advantages seen with single beams carry over to multiple beams. The benefits of reduced radiological penumbra for

Energy technology patents–CO2 emissions nexus: An empirical analysis from China

International Nuclear Information System (INIS)

Wang Zhaohua; Yang Zhongmin; Zhang Yixiang; Yin Jianhua

2012-01-01

Energy technology innovation plays a crucial role in reducing carbon emissions. This paper investigates whether there is relationship between energy technology patents and CO 2 emissions of 30 provinces in mainland China during 1997–2008. Gross domestic product (GDP) is included in the study due to its impact on CO 2 emissions and energy technology innovation, thus avoiding the problem of omitted variable bias. Furthermore, we investigate three cross-regional groups, namely eastern, central and western China. The results show that domestic patents for fossil-fueled technologies have no significant effect on CO 2 emissions reduction; however, domestic patents for carbon-free energy technologies appear to play an important role in reducing CO 2 emissions, which is significant in eastern China, but is not significant in central, western and national level of China. The results of this study enrich energy technology innovation theories and provide some implications for energy technology policy making. - Highlights: ► We studied the causality between energy technology patents and CO 2 emissions using dynamic panel data approach. ► There is a long-run equilibrium relationship among energy technology patents, CO 2 emissions and GDP. ► Domestic patents for fossil-fueled technologies have no significant effect on CO 2 emissions reduction. ► Domestic patents for carbon-free energy technologies appear to play an important role in reducing CO 2 emissions. ► This study provides some references for the future energy technology policy making.

Apparent Minimum Free Energy Requirements for Methanogenic Archaea and Sulfate-Reducing Bacteria in an Anoxic Marine Sediment

Science.gov (United States)

Hoehler, Tori M.; Alperin, Marc J.; Albert, Daniel B.; Martens, Christopher S.; DeVincenzi, Don (Technical Monitor)

2000-01-01

Among the most fundamental constraints governing the distribution of microorganisms in the environment is the availability of chemical energy at biologically useful levels. To assess the minimum free energy yield that can support microbial metabolism in situ, we examined the thermodynamics of H2-consuming processes in anoxic sediments from Cape Lookout Bight, NC, USA. Depth distributions of H2 partial pressure, along with a suite of relevant concentration data, were determined in sediment cores collected in November (at 14.5 C) and August (at 27 C) and used to calculate free energy yields for methanogenesis and sulfate reduction. At both times of year, and for both processes, free energy yields gradually decreased (became less negative) with depth before reaching an apparent asymptote. Sulfate reducing bacteria exhibited an asymptote of -19.1 +/- 1.7 kj(mol SO4(2-)(sup -1) while methanogenic archaea were apparently supported by energy yields as small as -10.6 +/- 0.7 kj(mol CH4)(sup -1).

Energy management: analysis of reducing energy consumption by sectors of the A.W. Faber-Castell S.A. company; Gerenciamento energetico: analise de reducao do consumo de energia eletrica de setores da empresa A.W. Faber-Castell S.A.

Energy Technology Data Exchange (ETDEWEB)

Silva, Jesue Ferraz da [Faculdades Integradas de Sao Carlos (FADISC), SP (Brazil); Branco, Fabio Jose Ceron [Universidade de Sao Paulo (EESC/USP), Sao Carlos, SP (Brazil). Escola de Engenharia

2009-07-01

The energy consumption in the sectors that require a lot of input from the company A.W. Faber-Castell S.A. after the implementation of the program to reduce energy consumption by the Internal Committee for Energy Conservation was studied. This program aimed to reduce by 0.5% of electric power in the company.

Reducing barriers to energy efficiency in the German energy service companies sector. Final report

Energy Technology Data Exchange (ETDEWEB)

Koewener, D.; Schleich, J.

2000-12-01

This report describes the empirical research conducted in the German energy service sector to assess to what extent energy service companies (ESCOs) can help overcome the barriers to energy in the higher education, brewing and mechanical engineering sectors. This report complements the sector for Germany within the BARRIERS project (Sorrell et al., 2000; Schleich/Boede 2000a; Schleich/Boede 2000b; Schleich et al., 2000). The report characterises the German energy service sector, contains a description and analysis of four case studies in the energy service sector, identifies the main barriers and chances for ESCOs in the higher education, brewery and mechanical engineering sectors, and concludes with brief recommendations on how these barriers may be overcome. The results of the study are summarised here under the following headings: Characterising the energy service sector in Germany; - Case studies of energy service companies in Germany; - The role of ESCOs in the case-study sectors; - Policy implications. (orig.)

Accelerator driven reactors, - the significance of the energy distribution of spallation neutrons on the neutron statistics

Energy Technology Data Exchange (ETDEWEB)

Fhager, V

2000-01-01

distribution of the spallation neutrons leads to second moments that differ significantly from the ones calculated with the average energy distribution only. With the most realistic model of the energy distributions, the second moment of the number of fissions was underestimated with 12-16%.

Accelerator driven reactors, - the significance of the energy distribution of spallation neutrons on the neutron statistics

International Nuclear Information System (INIS)

Fhager, V.

2000-01-01

distribution of the spallation neutrons leads to second moments that differ significantly from the ones calculated with the average energy distribution only. With the most realistic model of the energy distributions, the second moment of the number of fissions was underestimated with 12-16%

Energy efficiency labelling

Energy Technology Data Exchange (ETDEWEB)

1978-04-01

This research assesses the likely effects on UK consumers of the proposed EEC energy-efficiency labeling scheme. Unless (or until) an energy-labeling scheme is introduced, it is impossible to do more than postulate its likely effects on consumer behavior. This report shows that there are indeed significant differences in energy consumption between different brands and models of the same appliance of which consumers are unaware. Further, the report suggests that, if a readily intelligible energy-labeling scheme were introduced, it would provide useful information that consumers currently lack; and that, if this information were successfully presented, it would be used and could have substantial effects in reducing domestic fuel consumption. Therefore, it is recommended that an energy labeling scheme be introduced.

Reducing Demand Charges and Onsite Generation Variability Using Behind-the-Meter Energy Storage

Energy Technology Data Exchange (ETDEWEB)

Bhattarai, Bishnu P.; Myers, Kurt S.; Bush, Jason W.

2017-04-01

Electric utilities in the United States are increasingly employing demand charges and/or real-time pricing. This directive is bringing potential opportunities in deploying behindthe-meter energy storage (BMES) systems for various grid functionalities. This study quantifies techno-economic benefits of BMES in reducing demand charge and smoothing load/generation intermittencies, and determines how those benefits vary with onsite distributed photovoltaic. We proposed a two-stage control algorithm, whereby the first stage proactively determines costoptimal BMES configuration for reducing peak-demands and demand charges, and the second stage adaptively compensates intermittent generations and short load spikes that may otherwise increase the demand charges. The performance of the proposed algorithm is evaluated through a 24 hours time sweep simulation performed using data from smart microgrid testbed at Idaho National Laboratory (INL). The simulation results demonstrated that this research provides a simple but effective solution for peak shaving, demand charge reductions, and smoothing onsite PV variability.

Ascophyllum nodosum enriched bread reduces subsequent energy intake with no effect on post-prandial glucose and cholesterol in healthy, overweight males. A pilot study.

Science.gov (United States)

Hall, A C; Fairclough, A C; Mahadevan, K; Paxman, J R

2012-02-01

It is well recognised that the consumption of seaweed isolates (such as alginate) successfully reduce energy intake and modulate glycaemic and cholesterolaemic responses. However, to date, the effect of adding whole seaweed to bread has not been widely investigated. Hence, this study aims to investigate the acceptability of Ascophyllum nodosum enriched bread as part of a meal, and measure its effect on energy intake and nutrient absorption in overweight, healthy males to see if it has a similar impact. Results from the acceptability study, (79 untrained sensory panellists) indicated that it is acceptable to incorporate seaweed (A. nodosum) into a staple food such as bread at concentrations of up to 4% per 400 g wholemeal loaf. A single blind cross over trial (n=12 males, aged 40.1±12.5 years; BMI 30.8±4.4 kg/m(2)) was used to compare energy intake and nutrient uptake after a breakfast meal using the enriched bread (4% A. nodosum) against the control bread (0% A. nodosum). Consumption of the enriched bread at breakfast led to a significant reduction (16.4%) in energy intake at a test meal 4 h later. Differences between treatment arms for area under the curve, peak values, and time of peak for blood glucose and cholesterol were not significant. Further investigation of potential mechanisms of action is warranted. Copyright © 2011 Elsevier Ltd. All rights reserved.

Development of next generation tempered and ODS reduced activation ferritic/martensitic steels for fusion energy applications

Science.gov (United States)

Zinkle, S. J.; Boutard, J. L.; Hoelzer, D. T.; Kimura, A.; Lindau, R.; Odette, G. R.; Rieth, M.; Tan, L.; Tanigawa, H.

2017-09-01

Reduced activation ferritic/martensitic steels are currently the most technologically mature option for the structural material of proposed fusion energy reactors. Advanced next-generation higher performance steels offer the opportunity for improvements in fusion reactor operational lifetime and reliability, superior neutron radiation damage resistance, higher thermodynamic efficiency, and reduced construction costs. The two main strategies for developing improved steels for fusion energy applications are based on (1) an evolutionary pathway using computational thermodynamics modelling and modified thermomechanical treatments (TMT) to produce higher performance reduced activation ferritic/martensitic (RAFM) steels and (2) a higher risk, potentially higher payoff approach based on powder metallurgy techniques to produce very high strength oxide dispersion strengthened (ODS) steels capable of operation to very high temperatures and with potentially very high resistance to fusion neutron-induced property degradation. The current development status of these next-generation high performance steels is summarized, and research and development challenges for the successful development of these materials are outlined. Material properties including temperature-dependent uniaxial yield strengths, tensile elongations, high-temperature thermal creep, Charpy impact ductile to brittle transient temperature (DBTT) and fracture toughness behaviour, and neutron irradiation-induced low-temperature hardening and embrittlement and intermediate-temperature volumetric void swelling (including effects associated with fusion-relevant helium and hydrogen generation) are described for research heats of the new steels.

Solar-light photocatalytic disinfection using crystalline/amorphous low energy bandgap reduced TiO2

Science.gov (United States)

Kim, Youngmin; Hwang, Hee Min; Wang, Luyang; Kim, Ikjoon; Yoon, Yeoheung; Lee, Hyoyoung

2016-01-01

A generation of reactive oxygen species (ROS) from TiO2 under solar light has been long sought since the ROS can disinfect organic pollutants. We found that newly developed crystalline/amorphous reduced TiO2 (rTiO2) that has low energy bandgap can effectively generate ROS under solar light and successfully remove a bloom of algae. The preparation of rTiO2 is a one-pot and mass productive solution-process reduction using lithium-ethylene diamine (Li-EDA) at room temperature. Interestingly only the rutile phase of TiO2 crystal was reduced, while the anatase phase even in case of both anatase/rutile phased TiO2 was not reduced. Only reduced TiO2 materials can generate ROS under solar light, which was confirmed by electron spin resonance. Among the three different types of Li-EDA treated TiO2 (anatase, rutile and both phased TiO2), the both phased rTiO2 showed the best performance to produce ROS. The generated ROS effectively removed the common green algae Chlamydomonas. This is the first report on algae degradation under solar light, proving the feasibility of commercially available products for disinfection. PMID:27121120

CT energy weighting in the presence of scatter and limited energy resolution

International Nuclear Information System (INIS)

Schmidt, Taly Gilat