Hazardous waste minimization tracking system

International Nuclear Information System (INIS)

Railan, R.

1994-01-01

Under RCRA section 3002 9(b) and 3005f(h), hazardous waste generators and owners/operators of treatment, storage, and disposal facilities (TSDFs) are required to certify that they have a program in place to reduce the volume or quantity and toxicity of hazardous waste to the degree determined to be economically practicable. In many cases, there are environmental, as well as, economic benefits, for agencies that pursue pollution prevention options. Several state governments have already enacted waste minimization legislation (e.g., Massachusetts Toxic Use Reduction Act of 1989, and Oregon Toxic Use Reduction Act and Hazardous Waste Reduction Act, July 2, 1989). About twenty six other states have established legislation that will mandate some type of waste minimization program and/or facility planning. The need to address the HAZMIN (Hazardous Waste Minimization) Program at government agencies and private industries has prompted us to identify the importance of managing The HAZMIN Program, and tracking various aspects of the program, as well as the progress made in this area. The open-quotes WASTEclose quotes is a tracking system, which can be used and modified in maintaining the information related to Hazardous Waste Minimization Program, in a manageable fashion. This program maintains, modifies, and retrieves information related to hazardous waste minimization and recycling, and provides automated report generating capabilities. It has a built-in menu, which can be printed either in part or in full. There are instructions on preparing The Annual Waste Report, and The Annual Recycling Report. The program is very user friendly. This program is available in 3.5 inch or 5 1/4 inch floppy disks. A computer with 640K memory is required

Waste Minimization Measurement and Progress Reporting

International Nuclear Information System (INIS)

Stone, K.A.

1995-01-01

Westinghouse Savannah River Company is implementing productivity improvement concepts into the Waste Minimization Program by focusing on the positive initiatives taken to reduce waste generation at the Savannah River Site. Previous performance measures, based only on waste generation rates, proved to be an ineffective metric for measuring performance and promoting continuous improvements within the Program. Impacts of mission changes and non-routine operations impeded development of baseline waste generation rates and often negated waste generation trending reports. A system was developed to quantify, document and track innovative activities that impact waste volume and radioactivity/toxicity reductions. This system coupled with Management-driven waste disposal avoidance goals is proving to be a powerful tool to promote waste minimization awareness and the implementation of waste reduction initiatives. Measurement of waste not generated, in addition to waste generated, increases the credibility of the Waste Minimization Program, improves sharing of success stories, and supports development of regulatory and management reports

LLNL Waste Minimization Program Plan

International Nuclear Information System (INIS)

1990-01-01

This document is the February 14, 1990 version of the LLNL Waste Minimization Program Plan (WMPP). The Waste Minimization Policy field has undergone continuous changes since its formal inception in the 1984 HSWA legislation. The first LLNL WMPP, Revision A, is dated March 1985. A series of informal revision were made on approximately a semi-annual basis. This Revision 2 is the third formal issuance of the WMPP document. EPA has issued a proposed new policy statement on source reduction and recycling. This policy reflects a preventative strategy to reduce or eliminate the generation of environmentally-harmful pollutants which may be released to the air, land surface, water, or ground water. In accordance with this new policy new guidance to hazardous waste generators on the elements of a Waste Minimization Program was issued. In response to these policies, DOE has revised and issued implementation guidance for DOE Order 5400.1, Waste Minimization Plan and Waste Reduction reporting of DOE Hazardous, Radioactive, and Radioactive Mixed Wastes, final draft January 1990. This WMPP is formatted to meet the current DOE guidance outlines. The current WMPP will be revised to reflect all of these proposed changes when guidelines are established. Updates, changes and revisions to the overall LLNL WMPP will be made as appropriate to reflect ever-changing regulatory requirements. 3 figs., 4 tabs

Annual Waste Minimization Summary Report

International Nuclear Information System (INIS)

Haworth, D.M.

2011-01-01

This report summarizes the waste minimization efforts undertaken by National Security TechnoIogies, LLC, for the U. S. Department of Energy, National Nuclear Security Administration Nevada Site Office (NNSA/NSO), during calendar year 2010. The NNSA/NSO Pollution Prevention Program establishes a process to reduce the volume and toxicity of waste generated by NNSA/NSO activities and ensures that proposed methods of treatment, storage, and/or disposal of waste minimize potential threats to human health and the environment.

Separations: The path to waste minimization

International Nuclear Information System (INIS)

Bell, J.T.

1992-01-01

Waste materials usually are composed of large amounts of innocuous and frequently useful components mixed with lesser amounts of one or more hazardous components. The ultimate path to waste minimization is the separation of the lesser quantities of hazardous components from the innocuous components, and then recycle the useful components. This vision is so simple that everyone would be expected to properly manage waste. Several parameters interfere with this proper waste management, which encourages the open-quotes sweep it under the rugclose quotes or the open-quotes bury it allclose quotes attitudes, both of which delay and complicate proper waste management. The two primary parameters that interfere with proper waste management are: economics drives a process to a product without concerns of waste minimization, and emergency needs for immediate production of a product usually delays proper waste management. A third parameter in recent years is also interfering with proper waste management: quick relief of waste insults to political and public perceptions is promoting the open-quotes bury it allclose quotes attitude. A fourth parameter can promote better waste management for any scenario that suffers either or all of the first three parameters: separations technology can minimize wastes when the application of this technology is not voided by influence of the first three parameters. The US Department of Energy's management of nuclear waste has been seriously affected by the above four parameters. This paper includes several points about how the generation and management of DOE wastes have been, and continue to be, affected by these parameters. Particular separations technologies for minimizing the DOE wastes that must be stored for long periods are highlighted

Waste minimization/pollution prevention study of high-priority waste streams

International Nuclear Information System (INIS)

Ogle, R.B.

1994-03-01

Although waste minimization has been practiced by the Metals and Ceramics (M ampersand C) Division in the past, the effort has not been uniform or formalized. To establish the groundwork for continuous improvement, the Division Director initiated a more formalized waste minimization and pollution prevention program. Formalization of the division's pollution prevention efforts in fiscal year (FY) 1993 was initiated by a more concerted effort to determine the status of waste generation from division activities. The goal for this effort was to reduce or minimize the wastes identified as having the greatest impact on human health, the environment, and costs. Two broad categories of division wastes were identified as solid/liquid wastes and those relating to energy use (primarily electricity and steam). This report presents information on the nonradioactive solid and liquid wastes generated by division activities. More specifically, the information presented was generated by teams of M ampersand C staff members empowered by the Division Director to study specific waste streams

Waste minimization and pollution prevention awareness plan

International Nuclear Information System (INIS)

1991-01-01

The purpose of this plan is to document the Lawrence Livermore National Laboratory (LLNL) Waste Minimization and Pollution Prevention Awareness Program. The plan specifies those activities and methods that are or will be employed to reduce the quantity and toxicity of wastes generated at the site. The intent of this plan is to respond to and comply with (DOE's) policy and guidelines concerning the need for pollution prevention. The Plan is composed of a LLNL Waste Minimization and Pollution Prevention Awareness Program Plan and, as attachments, Program- and Department-specific waste minimization plans. This format reflects the fact that waste minimization is considered a line management responsibility and is to be addressed by each of the Programs and Departments. 14 refs

Waste minimization and pollution prevention awareness plan

Energy Technology Data Exchange (ETDEWEB)

1991-05-31

The purpose of this plan is to document the Lawrence Livermore National Laboratory (LLNL) Waste Minimization and Pollution Prevention Awareness Program. The plan specifies those activities and methods that are or will be employed to reduce the quantity and toxicity of wastes generated at the site. The intent of this plan is to respond to and comply with (DOE's) policy and guidelines concerning the need for pollution prevention. The Plan is composed of a LLNL Waste Minimization and Pollution Prevention Awareness Program Plan and, as attachments, Program- and Department-specific waste minimization plans. This format reflects the fact that waste minimization is considered a line management responsibility and is to be addressed by each of the Programs and Departments. 14 refs.

Waste Minimization and Pollution Prevention Awareness Plan

International Nuclear Information System (INIS)

1992-01-01

The purpose of this plan is to document the Lawrence Livermore National Laboratory (LLNL) Waste Minimization and Pollution Prevention Awareness Program. The plan specifies those activities and methods that are or will be employed to reduce the quantity and toxicity of wastes generated at the site. It is intended to satisfy Department of Energy (DOE) and other legal requirements that are discussed in Section C, below. The Pollution Prevention Awareness Program is included with the Waste Minimization Program as suggested by DOE Order 5400.1. The intent of this plan is to respond to and comply with the Department's policy and guidelines concerning the need for pollution prevention. The Plan is composed of a LLNL Waste Minimization and Pollution Prevention Awareness Program Plan and, as attachments, Directorate-, Program- and Department-specific waste minimization plans. This format reflects the fact that waste minimization is considered a line management responsibility and is to be addressed by each of the Directorates, Programs and Departments. Several Directorates have been reorganized, necessitating changes in the Directorate plans that were published in 1991

Assessment of LANL waste minimization plan

International Nuclear Information System (INIS)

Davis, K.D.; McNair, D.A.; Jennrich, E.A.; Lund, D.M.

1991-04-01

The objective of this report is to evaluate the Los Alamos National Laboratory (LANL) Waste Minimization Plan to determine if it meets applicable internal (DOE) and regulatory requirements. The intent of the effort is to assess the higher level elements of the documentation to determine if they have been addressed rather than the detailed mechanics of the program's implementation. The requirement for a Waste Minimization Plan is based in several DOE Orders as well as environmental laws and regulations. Table 2-1 provides a list of the major documents or regulations that require waste minimization efforts. The table also summarizes the applicable requirements

Development of a waste minimization plan for a Department of Energy remedial action program: Ideas for minimizing waste in remediation scenarios

International Nuclear Information System (INIS)

Hubbard, Linda M.; Galen, Glen R.

1992-01-01

Waste minimization has become an important consideration in the management of hazardous waste because of regulatory as well as cost considerations. Waste minimization techniques are often process specific or industry specific and generally are not applicable to site remediation activities. This paper will examine ways in which waste can be minimized in a remediation setting such as the U.S. Department of Energy's Formerly Utilized Sites Remedial Action Program, where the bulk of the waste produced results from remediating existing contamination, not from generating new waste. (author)

National Institutes of Health: Mixed waste minimization and treatment

International Nuclear Information System (INIS)

1995-08-01

The Appalachian States Low-Level Radioactive Waste Commission requested the US Department of Energy's National Low-Level Waste Management Program (NLLWMP) to assist the biomedical community in becoming more knowledgeable about its mixed waste streams, to help minimize the mixed waste stream generated by the biomedical community, and to identify applicable treatment technologies for these mixed waste streams. As the first step in the waste minimization process, liquid low-level radioactive mixed waste (LLMW) streams generated at the National Institutes of Health (NIH) were characterized and combined into similar process categories. This report identifies possible waste minimization and treatment approaches for the LLMW generated by the biomedical community identified in DOE/LLW-208. In development of the report, on site meetings were conducted with NIH personnel responsible for generating each category of waste identified as lacking disposal options. Based on the meetings and general waste minimization guidelines, potential waste minimization options were identified

National Institutes of Health: Mixed waste minimization and treatment

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-08-01

The Appalachian States Low-Level Radioactive Waste Commission requested the US Department of Energy`s National Low-Level Waste Management Program (NLLWMP) to assist the biomedical community in becoming more knowledgeable about its mixed waste streams, to help minimize the mixed waste stream generated by the biomedical community, and to identify applicable treatment technologies for these mixed waste streams. As the first step in the waste minimization process, liquid low-level radioactive mixed waste (LLMW) streams generated at the National Institutes of Health (NIH) were characterized and combined into similar process categories. This report identifies possible waste minimization and treatment approaches for the LLMW generated by the biomedical community identified in DOE/LLW-208. In development of the report, on site meetings were conducted with NIH personnel responsible for generating each category of waste identified as lacking disposal options. Based on the meetings and general waste minimization guidelines, potential waste minimization options were identified.

Implementation of Waste Minimization at a complex R ampersand D site

International Nuclear Information System (INIS)

Lang, R.E.; Thuot, J.R.; Devgun, J.S.

1995-01-01

Under the 1994 Waste Minimization/Pollution Prevention Crosscut Plan, the Department of Energy (DOE) has set a goal of 50% reduction in waste at its facilities by the end of 1999. Each DOE site is required to set site-specific goals to reduce generation of all types of waste including hazardous, radioactive, and mixed. To meet these goals, Argonne National Laboratory (ANL), Argonne, IL, has developed and implemented a comprehensive Pollution Prevention/Waste Minimization (PP/WMin) Program. The facilities and activities at the site vary from research into basic sciences and research into nuclear fuel cycle to high energy physics and decontamination and decommissioning projects. As a multidisciplinary R ampersand D facility and a multiactivity site, ANL generates waste streams that are varied, in physical form as well as in chemical constituents. This in turn presents a significant challenge to put a cohesive site-wide PP/WMin Program into action. In this paper, we will describe ANL's key activities and waste streams, the regulatory drivers for waste minimization, and the DOE goals in this area, and we will discuss ANL's strategy for waste minimization and it's implementation across the site

Minimization of mixed waste in explosive testing operations

International Nuclear Information System (INIS)

Gonzalez, M.A.; Sator, F.E.; Simmons, L.F.

1993-02-01

In the 1970s and 1980s, efforts to manage mixed waste and reduce pollution focused largely on post-process measures. In the late 1980s, the approach to waste management and pollution control changed, focusing on minimization and prevention rather than abatement, treatment, and disposal. The new approach, and the formulated guidance from the US Department of Energy, was to take all necessary measures to minimize waste and prevent the release of pollutants to the environment. Two measures emphasized in particular were source reduction (reducing the volume and toxicity of the waste source) and recycling. In 1988, a waste minimization and pollution prevention program was initiated at Site 300, where the Lawrence Livermore National Laboratory (LLNL) conducts explosives testing. LLNL's Defense Systems/Nuclear Design (DS/ND) Program has adopted a variety of conservation techniques to minimize waste generation and cut disposal costs associated with ongoing operations. The techniques include minimizing the generation of depleted uranium and lead mixed waste through inventory control and material substitution measures and through developing a management system to recycle surplus explosives. The changes implemented have reduced annual mixed waste volumes by more than 95% and reduced overall radioactive waste generation (low-level and mixed) by more than 75%. The measures employed were cost-effective and easily implemented

Waste minimization - Hanford's strategy for sustainability

International Nuclear Information System (INIS)

Merry, D.S.

1998-01-01

The Hanford Site cleanup activity is an immense and challenging undertaking, which includes characterization and decommissioning of 149 single-shell storage tanks, treating waste stored in 28 double-shell tanks, safely disposing of over 2,100 metric tons of spent nuclear fuel stored onsite, removing thousands of structures, and dealing with significant solid waste, groundwater, and land restoration issues. The Pollution Prevention/Waste Minimization (P2/WMin) Program supports the Hanford Site mission to safely clean up and manage legacy waste and to develop and deploy science and technology in many ways. Once such way is through implementing and documenting over 231 waste reduction projects during the past five years, resulting in over $93 million in cost savings/avoidances. These savings/avoidances allowed other high priority cleanup work to be performed. Another way is by exceeding the Secretary of Energy's waste reduction goals over two years ahead of schedule, thus reducing the amount of waste to be stored, treated and disposed. Six key elements are the foundation for these sustained P2/WMin results

Minimization and segregation of radioactive wastes

International Nuclear Information System (INIS)

1992-07-01

The report will serve as one of a series of technical manuals providing reference material and direct know-how to staff in radioisotope user establishments and research centres in Member States without nuclear power and the associated range of complex waste management operations. Considerations are limited to the minimization and segregation of wastes, these being initial steps on which the efficiency of the whole waste management system depends. The minimization and segregation operations are examined in the context of the restricted quantities and predominantly shorter lived activities of wastes from nuclear research, production and usage of radioisotopes. Liquid and solid wastes only are considered in the report. Gaseous waste minimization and treatment are specialized subjects and are not examined in this document. Gaseous effluent treatment in facilities handling low and intermediate level radioactive materials has been already the subject of a detailed IAEA report. Management of spent sealed sources has specifically been covered in a previous manual. Conditioned sealed sources must be taken into account in segregation arrangements for interim storage and disposal where there are exceptional long lived highly radiotoxic isotopes, particularly radium or americium. These are unlikely ever to be suitable for shallow land burial along with the remaining wastes. 30 refs, 5 figs, 8 tabs

Minimization of radioactive solid wastes from uranium mining and metallurgy

International Nuclear Information System (INIS)

Zhang Xueli; Xu Lechang; Wei Guangzhi; Gao Jie; Wang Erqi

2010-01-01

The concept and contents of radioactive waste minimization are introduced. The principle of radioactive waste minimization involving administration optimization, source reduction, recycling and reuse as well as volume reduction are discussed. The strategies and methods to minimize radioactive solid wastes from uranium mining and metallurgy are summarized. In addition, the benefit from its application of radioactive waste minimization is analyzed. Prospects for the research on radioactive so-lid waste minimization are made in the end. (authors)

Automated economic analysis model for hazardous waste minimization

International Nuclear Information System (INIS)

Dharmavaram, S.; Mount, J.B.; Donahue, B.A.

1990-01-01

The US Army has established a policy of achieving a 50 percent reduction in hazardous waste generation by the end of 1992. To assist the Army in reaching this goal, the Environmental Division of the US Army Construction Engineering Research Laboratory (USACERL) designed the Economic Analysis Model for Hazardous Waste Minimization (EAHWM). The EAHWM was designed to allow the user to evaluate the life cycle costs for various techniques used in hazardous waste minimization and to compare them to the life cycle costs of current operating practices. The program was developed in C language on an IBM compatible PC and is consistent with other pertinent models for performing economic analyses. The potential hierarchical minimization categories used in EAHWM include source reduction, recovery and/or reuse, and treatment. Although treatment is no longer an acceptable minimization option, its use is widespread and has therefore been addressed in the model. The model allows for economic analysis for minimization of the Army's six most important hazardous waste streams. These include, solvents, paint stripping wastes, metal plating wastes, industrial waste-sludges, used oils, and batteries and battery electrolytes. The EAHWM also includes a general application which can be used to calculate and compare the life cycle costs for minimization alternatives of any waste stream, hazardous or non-hazardous. The EAHWM has been fully tested and implemented in more than 60 Army installations in the United States

INTELLIGENT DECISION SUPPORT FOR WASTE MINIMIZATION IN ELECTROPLATING PLANTS. (R824732)

Science.gov (United States)

AbstractWastewater, spent solvent, spent process solutions, and sludge are the major waste streams generated in large volumes daily in electroplating plants. These waste streams can be significantly minimized through process modification and operational improvement. I...

Environmental Restoration Progam Waste Minimization and Pollution Prevention Awareness Program Plan

Energy Technology Data Exchange (ETDEWEB)

Grumski, J. T.; Swindle, D. W.; Bates, L. D.; DeLozier, M. F.P.; Frye, C. E.; Mitchell, M. E.

1991-09-30

In response to DOE Order 5400.1 this plan outlines the requirements for a Waste Minimization and Pollution Prevention Awareness Program for the Environmental Restoration (ER) Program at Martin Marietta Energy System, Inc. Statements of the national, Department of Energy, Energy Systems, and Energy Systems ER Program policies on waste minimization are included and reflect the attitudes of these organizations and their commitment to the waste minimization effort. Organizational responsibilities for the waste minimization effort are clearly defined and discussed, and the program objectives and goals are set forth. Waste assessment is addressed as being a key element in developing the waste generation baseline. There are discussions on the scope of ER-specific waste minimization techniques and approaches to employee awareness and training. There is also a discussion on the process for continual evaluation of the Waste Minimization Program. Appendixes present an implementation schedule for the Waste Minimization and Pollution Prevention Program, the program budget, an organization chart, and the ER waste minimization policy.

Environmental Restoration Progam Waste Minimization and Pollution Prevention Awareness Program Plan

International Nuclear Information System (INIS)

1991-01-01

In response to DOE Order 5400.1 this plan outlines the requirements for a Waste Minimization and Pollution Prevention Awareness Program for the Environmental Restoration (ER) Program at Martin Marietta Energy System, Inc. Statements of the national, Department of Energy, Energy Systems, and Energy Systems ER Program policies on waste minimization are included and reflect the attitudes of these organizations and their commitment to the waste minimization effort. Organizational responsibilities for the waste minimization effort are clearly defined and discussed, and the program objectives and goals are set forth. Waste assessment is addressed as being a key element in developing the waste generation baseline. There are discussions on the scope of ER-specific waste minimization techniques and approaches to employee awareness and training. There is also a discussion on the process for continual evaluation of the Waste Minimization Program. Appendixes present an implementation schedule for the Waste Minimization and Pollution Prevention Program, the program budget, an organization chart, and the ER waste minimization policy

Waste minimization for commercial radioactive materials users generating low-level radioactive waste

International Nuclear Information System (INIS)

Fischer, D.K.; Gitt, M.; Williams, G.A.; Branch, S.; Otis, M.D.; McKenzie-Carter, M.A.; Schurman, D.L.

1991-07-01

The objective of this document is to provide a resource for all states and compact regions interested in promoting the minimization of low-level radioactive waste (LLW). This project was initiated by the Commonwealth of Massachusetts, and Massachusetts waste streams have been used as examples; however, the methods of analysis presented here are applicable to similar waste streams generated elsewhere. This document is a guide for states/compact regions to use in developing a system to evaluate and prioritize various waste minimization techniques in order to encourage individual radioactive materials users (LLW generators) to consider these techniques in their own independent evaluations. This review discusses the application of specific waste minimization techniques to waste streams characteristic of three categories of radioactive materials users: (1) industrial operations using radioactive materials in the manufacture of commercial products, (2) health care institutions, including hospitals and clinics, and (3) educational and research institutions. Massachusetts waste stream characterization data from key radioactive materials users in each category are used to illustrate the applicability of various minimization techniques. The utility group is not included because extensive information specific to this category of LLW generators is available in the literature

Environmental Restoration Program waste minimization and pollution prevention self-assessment

International Nuclear Information System (INIS)

1994-10-01

The Environmental Restoration (ER) Program within Martin Marietta Energy Systems, Inc. is currently developing a more active waste minimization and pollution prevention program. To determine areas of programmatic improvements within the ER Waste Minimization and Pollution Prevention Awareness Program, the ER Program required an evaluation of the program across the Oak Ridge K-25 Site, the Oak Ridge National Laboratory, the Oak Ridge Y-12 Plant, the Paducah Environmental Restoration and Waste Minimization Site, and the Portsmouth Environmental Restoration and Waste Minimization Site. This document presents the status of the overall program as of fourth quarter FY 1994, presents pollution prevention cost avoidance data associated with FY 1994 activities, and identifies areas for improvement. Results of this assessment indicate that the ER Waste Minimization and Pollution Prevention Awareness Program is firmly established and is developing rapidly. Several procedural goals were met in FY 1994 and many of the sites implemented ER waste minimization options. Additional growth is needed, however, for the ER Waste Minimization and Pollution Prevention Awareness Program

LLNL Waste Minimization Program Plan

International Nuclear Information System (INIS)

1990-05-01

This document is the February 14, 1990 version of the LLNL Waste Minimization Program Plan (WMPP). Now legislation at the federal level is being introduced. Passage will result in new EPA regulations and also DOE orders. At the state level the Hazardous Waste Reduction and Management Review Act of 1989 was signed by the Governor. DHS is currently promulgating regulations to implement the new law. EPA has issued a proposed new policy statement on source reduction and recycling. This policy reflects a preventative strategy to reduce or eliminate the generation of environmentally-harmful pollutants which may be released to the air, land surface, water, or ground water. In accordance with this policy new guidance to hazardous waste generators on the elements of a Waste Minimization Program was issued. This WMPP is formatted to meet the current DOE guidance outlines. The current WMPP will be revised to reflect all of these proposed changes when guidelines are established. Updates, changes and revisions to the overall LLNL WMPP will be made as appropriate to reflect ever-changing regulatory requirements

Experience with the EPA manual for waste minimization opportunity assessments

International Nuclear Information System (INIS)

Bridges, J.S.

1990-01-01

The EPA Waste Minimization Opportunity Assessment Manual (EPA/625/788/003) was published to assist those responsible for managing waste minimization activities at the waste generating facility and at corporate levels. The Manual sets forth a procedure that incorporates technical and managerial principles and motivates people to develop and implement pollution prevention concepts and ideas. Environmental management has increasingly become one of cooperative endeavor whereby whether in government, industry, or other forms of enterprise, the effectiveness with whirl, people work together toward the attainment of a clean environment is largely determined by the ability of those who hold managerial position. This paper offers a description of the EPA Waste Minimization Opportunity Assessment Manual procedure which supports the waste minimization assessment as a systematic planned procedure with the objective of identifying ways to reduce or eliminate waste generation. The Manual is a management tool that blends science and management principles. The practice of managing waste minimization/pollution prevention makes use of the underlying organized science and engineering knowledge and applies it in the light of realities to gain a desired, practical result. The early stages of EPA's Pollution Prevention Research Program centered on the development of the Manual and its use at a number of facilities within the private and public sectors. This paper identifies a number of case studies and waste minimization opportunity assessment reports that demonstrate the value of using the Manual's approach. Several industry-specific waste minimization assessment manuals have resulted from the Manual's generic approach to waste minimization. There were some modifications to the Manual's generic approach when the waste stream has been other than industrial hazardous waste

2013 Los Alamos National Laboratory Hazardous Waste Minimization Report

Energy Technology Data Exchange (ETDEWEB)

Salzman, Sonja L. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); English, Charles J. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-08-24

Waste minimization and pollution prevention are inherent goals within the operating procedures of Los Alamos National Security, LLC (LANS). The US Department of Energy (DOE) and LANS are required to submit an annual hazardous waste minimization report to the New Mexico Environment Department (NMED) in accordance with the Los Alamos National Laboratory (LANL or the Laboratory) Hazardous Waste Facility Permit. The report was prepared pursuant to the requirements of Section 2.9 of the LANL Hazardous Waste Facility Permit. This report describes the hazardous waste minimization program (a component of the overall Waste Minimization/Pollution Prevention [WMin/PP] Program) administered by the Environmental Stewardship Group (ENV-ES). This report also supports the waste minimization and pollution prevention goals of the Environmental Programs Directorate (EP) organizations that are responsible for implementing remediation activities and describes its programs to incorporate waste reduction practices into remediation activities and procedures. LANS was very successful in fiscal year (FY) 2013 (October 1-September 30) in WMin/PP efforts. Staff funded four projects specifically related to reduction of waste with hazardous constituents, and LANS won four national awards for pollution prevention efforts from the National Nuclear Security Administration (NNSA). In FY13, there was no hazardous, mixedtransuranic (MTRU), or mixed low-level (MLLW) remediation waste generated at the Laboratory. More hazardous waste, MTRU waste, and MLLW was generated in FY13 than in FY12, and the majority of the increase was related to MTRU processing or lab cleanouts. These accomplishments and analysis of the waste streams are discussed in much more detail within this report.

Waste Minimization Policy at the Romanian Nuclear Power Plant

International Nuclear Information System (INIS)

Andrei, V.; Daian, I.

2002-01-01

The radioactive waste management system at Cernavoda Nuclear Power Plant (NPP) in Romania was designed to maintain acceptable levels of safety for workers and to protect human health and the environment from exposure to unacceptable levels of radiation. In accordance with terminology of the International Atomic Energy Agency (IAEA), this system consists of the ''pretreatment'' of solid and organic liquid radioactive waste, which may include part or all of the following activities: collection, handling, volume reduction (by an in-drum compactor, if appropriate), and storage. Gaseous and aqueous liquid wastes are managed according to the ''dilute and discharge'' strategy. Taking into account the fact that treatment/conditioning and disposal technologies are still not established, waste minimization at the source is a priority environmental management objective, while waste minimization at the disposal stage is presently just a theoretical requirement for future adopted technologies . The necessary operational and maintenance procedures are in place at Cernavoda to minimize the production and contamination of waste. Administrative and technical measures are established to minimize waste volumes. Thus, an annual environmental target of a maximum 30 m3 of radioactive waste volume arising from operation and maintenance has been established. Within the first five years of operations at Cernavoda NPP, this target has been met. The successful implementation of the waste minimization policy has been accompanied by a cost reduction while the occupational doses for plant workers have been maintained at as low as reasonably practicable levels. This paper will describe key features of the waste management system along with the actual experience that has been realized with respect to minimizing the waste volumes at the Cernavoda NPP

Waste minimization -- Hanford`s strategy for sustainability

Energy Technology Data Exchange (ETDEWEB)

Merry, D.S.

1998-01-30

The Hanford Site cleanup activity is an immense and challenging undertaking, which includes characterization and decommissioning of 149 single-shell storage tanks, treating waste stored in 28 double-shell tanks, safely disposing of over 2,100 metric tons of spent nuclear fuel stored onsite, removing thousands of structures, and dealing with significant solid waste, groundwater, and land restoration issues. The Pollution Prevention/Waste Minimization (P2/WMin) Program supports the Hanford Site mission to safely clean up and manage legacy waste and to develop and deploy science and technology in many ways. Once such way is through implementing and documenting over 231 waste reduction projects during the past five years, resulting in over $93 million in cost savings/avoidances. These savings/avoidances allowed other high priority cleanup work to be performed. Another way is by exceeding the Secretary of Energy`s waste reduction goals over two years ahead of schedule, thus reducing the amount of waste to be stored, treated and disposed. Six key elements are the foundation for these sustained P2/WMin results.

The Construction Solid Waste Minimization Practices among Malaysian Contractors

Directory of Open Access Journals (Sweden)

Che Ahmad A.

2014-01-01

Full Text Available The function of minimization of construction solid waste is to reduce or eliminates the adverse impacts on the environment and to human health. Due to the increase of population that leads to rapid development, there are possibilities of construction solid waste to be increased shortly from the construction works, demolition or renovation works. Materials such as wood, concrete, paint, brick, roofing, tiles, plastic and any other materials would contribute problem involving construction solid waste. Therefore, the proper waste minimization is needed to control the quantity of construction solid waste produced. This paper identifies the type of construction solid waste produced and discusses the waste minimization practice by the contractors at construction sites in Selangor, Kuala Lumpur and Putrajaya, Malaysia.

2016 Los Alamos National Laboratory Hazardous Waste Minimization Report

Energy Technology Data Exchange (ETDEWEB)

Salzman, Sonja L. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); English, Charles Joe [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-12-02

Waste minimization and pollution prevention are goals within the operating procedures of Los Alamos National Security, LLC (LANS). The US Department of Energy (DOE), inclusive of the National Nuclear Security Administration (NNSA) and the Office of Environmental Management, and LANS are required to submit an annual hazardous waste minimization report to the New Mexico Environment Department (NMED) in accordance with the Los Alamos National Laboratory (LANL or the Laboratory) Hazardous Waste Facility Permit. The report was prepared pursuant to the requirements of Section 2.9 of the LANL Hazardous Waste Facility Permit. This report describes the hazardous waste minimization program, which is a component of the overall Pollution Prevention (P2) Program, administered by the Environmental Stewardship Group (EPC-ES). This report also supports the waste minimization and P2 goals of the Associate Directorate of Environmental Management (ADEM) organizations that are responsible for implementing remediation activities and describes its programs to incorporate waste reduction practices into remediation activities and procedures. This report includes data for all waste shipped offsite from LANL during fiscal year (FY) 2016 (October 1, 2015 – September 30, 2016). LANS was active during FY2016 in waste minimization and P2 efforts. Multiple projects were funded that specifically related to reduction of hazardous waste. In FY2016, there was no hazardous, mixed-transuranic (MTRU), or mixed low-level (MLLW) remediation waste shipped offsite from the Laboratory. More non-remediation hazardous waste and MLLW was shipped offsite from the Laboratory in FY2016 compared to FY2015. Non-remediation MTRU waste was not shipped offsite during FY2016. These accomplishments and analysis of the waste streams are discussed in much more detail within this report.

Minimally processed beetroot waste as an alternative source to obtain functional ingredients.

Science.gov (United States)

Costa, Anne Porto Dalla; Hermes, Vanessa Stahl; Rios, Alessandro de Oliveira; Flôres, Simone Hickmann

2017-06-01

Large amounts of waste are generated by the minimally processed vegetables industry, such as those from beetroot processing. The aim of this study was to determine the best method to obtain flour from minimally processed beetroot waste dried at different temperatures, besides producing a colorant from such waste and assessing its stability along 45 days. Beetroot waste dried at 70 °C originates flour with significant antioxidant activity and higher betalain content than flour produced from waste dried at 60 and 80 °C, while chlorination had no impact on the process since microbiological results were consistent for its application. The colorant obtained from beetroot waste showed color stability for 20 days and potential antioxidant activity over the analysis period, thus it can be used as a functional additive to improve nutritional characteristics and appearance of food products. These results are promising since minimally processed beetroot waste can be used as an alternative source of natural and functional ingredients with high antioxidant activity and betalain content.

The OTD Robotics Waste Minimization Program

International Nuclear Information System (INIS)

Couture, S.A.

1992-04-01

The danger to human health and safety posed by exposure to transuranic (TRU) and Pu contaminated materials necessitates remote processing in confined environments. Currently these operations are carried out in gloveboxes and hot-cells by human operators using lead- lined gloves or teleoperated manipulators. Protective clothing worn by operators during gloved operations has contributed significantly to the waste problems currently facing site remediators. The DOE Environmental Restoration and Waste Management (ER/WM) Program is in the process of developing and demonstrating technologies to assist in the remediation of sites that have accumulated wastes generated using these processes over the past five decades. Recognizing that continued use of existing production, recovery and waste treatment systems will compound the remediation problem, DOE has made a commitment to waste minimization. To reduce waste generation during weapons production and waste processing operations, automated processes are being developed and demonstrated for use in future DOE processing facilities as part of OTD's Robotics Technology Development Program. These technologies are currently being applied to pyrochemical processing systems to demonstrate conversion of plutonium oxide to metal. However, these technologies are expected to have applications in a variety of waste processing systems including those used to treat high-level tank wastes, buried wastes requiring remote processing, mixed wastes, and unknown hazardous materials. In addition to reducing the future waste burden of DOE, automated processes are an effective way to comply with existing and anticipated federal, state, and local regulations related to personal health and safety and the health of the environment

Commercial radioactive waste minimization program development guidance

International Nuclear Information System (INIS)

Fischer, D.K.

1991-01-01

This document is one of two prepared by the EG ampersand G Idaho, Inc., Waste Management Technical Support Program Group, National Low-Level Waste Management Program Unit. One of several Department of Energy responsibilities stated in the Amendments Act of 1985 is to provide technical assistance to compact regions Host States, and nonmember States (to the extent provided in appropriations acts) in establishing waste minimization program plans. Technical assistance includes, among other things, the development of technical guidelines for volume reduction options. Pursuant to this defined responsibility, the Department of Energy (through EG ampersand G Idaho, Inc.) has prepared this report, which includes guidance on defining a program, State/compact commission participation, and waste minimization program plans

Westinghouse Hanford Company waste minimization and pollution prevention awareness program plan

International Nuclear Information System (INIS)

Craig, P.A.; Nichols, D.H.; Lindsey, D.W.

1991-08-01

The purpose of this plan is to establish the Westinghouse Hanford Company's Waste Minimization Program. The plan specifies activities and methods that will be employed to reduce the quantity and toxicity of waste generated at Westinghouse Hanford Company (Westinghouse Hanford). It is designed to satisfy the US Department of Energy (DOE) and other legal requirements that are discussed in Subsection C of the section. The Pollution Prevention Awareness Program is included with the Waste Minimization Program as permitted by DOE Order 5400.1 (DOE 1988a). This plan is based on the Hanford Site Waste Minimization and Pollution Prevention Awareness Program Plan, which directs DOE Field Office, Richland contractors to develop and maintain a waste minimization program. This waste minimization program is an organized, comprehensive, and continual effort to systematically reduce waste generation. The Westinghouse Hanford Waste Minimization Program is designed to prevent or minimize pollutant releases to all environmental media from all aspects of Westinghouse Hanford operations and offers increased protection of public health and the environment. 14 refs., 2 figs., 1 tab

Critical management practices influencing on-site waste minimization in construction projects.

Science.gov (United States)

Ajayi, Saheed O; Oyedele, Lukumon O; Bilal, Muhammad; Akinade, Olugbenga O; Alaka, Hafiz A; Owolabi, Hakeem A

2017-01-01

As a result of increasing recognition of effective site management as the strategic approach for achieving the required performance in construction projects, this study seeks to identify the key site management practices that are requisite for construction waste minimization. A mixed methods approach, involving field study and survey research were used as means of data collection. After confirmation of construct validity and reliability of scale, data analysis was carried out through a combination of Kruskal-Wallis test, descriptive statistics and exploratory factor analysis. The study suggests that site management functions could significantly reduce waste generation through strict adherence to project drawings, and by ensuring fewer or no design changes during construction process. Provision of waste skips for specific materials and maximisation of on-site reuse of materials are also found to be among the key factors for engendering waste minimization. The result of factor analysis suggests four factors underlying on-site waste management practices with 96.093% of total variance. These measures include contractual provisions for waste minimization, waste segregation, maximisation of materials reuse and effective logistic management. Strategies through which each of the underlying measures could be achieved are further discussed in the paper. Findings of this study would assist construction site managers and other site operatives in reducing waste generated by construction activities. Copyright © 2016 Elsevier Ltd. All rights reserved.

Using benchmarking to minimize common DOE waste streams. Volume 1, Methodology and liquid photographic waste

Energy Technology Data Exchange (ETDEWEB)

Levin, V.

1994-04-01

Finding innovative ways to reduce waste streams generated at Department of Energy (DOE) sites by 50% by the year 2000 is a challenge for DOE`s waste minimization efforts. This report examines the usefulness of benchmarking as a waste minimization tool, specifically regarding common waste streams at DOE sites. A team of process experts from a variety of sites, a project leader, and benchmarking consultants completed the project with management support provided by the Waste Minimization Division EM-352. Using a 12-step benchmarking process, the team examined current waste minimization processes for liquid photographic waste used at their sites and used telephone and written questionnaires to find ``best-in-class`` industrv partners willing to share information about their best waste minimization techniques and technologies through a site visit. Eastman Kodak Co., and Johnson Space Center/National Aeronautics and Space Administration (NASA) agreed to be partners. The site visits yielded strategies for source reduction, recycle/recovery of components, regeneration/reuse of solutions, and treatment of residuals, as well as best management practices. An additional benefit of the work was the opportunity for DOE process experts to network and exchange ideas with their peers at similar sites.

Mixed low-level waste minimization at Los Alamos

International Nuclear Information System (INIS)

Starke, T.P.

1998-01-01

During the first six months of University of California 98 Fiscal Year (July--December) Los Alamos National Laboratory has achieved a 57% reduction in mixed low-level waste generation. This has been accomplished through a systems approach that identified and minimized the largest MLLW streams. These included surface-contaminated lead, lead-lined gloveboxes, printed circuit boards, and activated fluorescent lamps. Specific waste minimization projects have been initiated to address these streams. In addition, several chemical processing equipment upgrades are being implemented. Use of contaminated lead is planned for several high energy proton beam stop applications and stainless steel encapsulated lead is being evaluated for other radiological control area applications. INEEL is assisting Los Alamos with a complete systems analysis of analytical chemistry derived mixed wastes at the CMR building and with a minimum life-cycle cost standard glovebox design. Funding for waste minimization upgrades has come from several sources: generator programs, waste management, the generator set-aside program, and Defense Programs funding to INEEL

Mixed low-level waste minimization at Los Alamos

Energy Technology Data Exchange (ETDEWEB)

Starke, T.P.

1998-12-01

During the first six months of University of California 98 Fiscal Year (July--December) Los Alamos National Laboratory has achieved a 57% reduction in mixed low-level waste generation. This has been accomplished through a systems approach that identified and minimized the largest MLLW streams. These included surface-contaminated lead, lead-lined gloveboxes, printed circuit boards, and activated fluorescent lamps. Specific waste minimization projects have been initiated to address these streams. In addition, several chemical processing equipment upgrades are being implemented. Use of contaminated lead is planned for several high energy proton beam stop applications and stainless steel encapsulated lead is being evaluated for other radiological control area applications. INEEL is assisting Los Alamos with a complete systems analysis of analytical chemistry derived mixed wastes at the CMR building and with a minimum life-cycle cost standard glovebox design. Funding for waste minimization upgrades has come from several sources: generator programs, waste management, the generator set-aside program, and Defense Programs funding to INEEL.

Advanced pyrochemical technologies for minimizing nuclear waste

International Nuclear Information System (INIS)

Bronson, M.C.; Dodson, K.E.; Riley, D.C.

1994-01-01

The Department of Energy (DOE) is seeking to reduce the size of the current nuclear weapons complex and consequently minimize operating costs. To meet this DOE objective, the national laboratories have been asked to develop advanced technologies that take uranium and plutonium, from retired weapons and prepare it for new weapons, long-term storage, and/or final disposition. Current pyrochemical processes generate residue salts and ceramic wastes that require aqueous processing to remove and recover the actinides. However, the aqueous treatment of these residues generates an estimated 100 liters of acidic transuranic (TRU) waste per kilogram of plutonium in the residue. Lawrence Livermore National Laboratory (LLNL) is developing pyrochemical techniques to eliminate, minimize, or more efficiently treat these residue streams. This paper will present technologies being developed at LLNL on advanced materials for actinide containment, reactors that minimize residues, and pyrochemical processes that remove actinides from waste salts

Recent developments in the DOE Waste Minimization Pollution Prevention Program

International Nuclear Information System (INIS)

Hancock, J.K.

1993-01-01

The U.S. Department of Energy (DOE) is involved in a wide variety of research and development, remediation, and production activities at more than 100 sites throughout the United States. The wastes generated cover a diverse spectrum of sanitary, hazardous, and radioactive waste streams, including typical office environments, power generation facilities, laboratories, remediation sites, production facilities, and defense facilities. The DOE's initial waste minimization activities pre-date the Pollution Prevention Act of 1990 and focused on the defense program. Little emphasis was placed on nonproduction activities. In 1991 the Office of Waste Management Operations developed the Waste Minimization Division with the intention of coordinating and expanding the waste minimization pollution prevention approach to the entire complex. The diverse nature of DOE activities has led to several unique problems in addressing the needs of waste minimization and pollution prevention. The first problem is developing a program that addresses the geographical and institutional hurdles that exist; the second is developing a monitoring and reporting mechanism that one can use to assess the overall performance of the program

Minimization of waste from uranium purification, enrichment and fuel fabrication

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-10-01

As any industry, nuclear industry generates a diverse range of waste which has to be managed in a safe manner to be acceptable to the public and the environment. The cost of waste management, the risks to the public and employees, and the detriment to the environment are dependent on the quantity and radioactive content of the waste generated. Waste minimization is a necessary activity needed to reduce the impact from nuclear fuel cycle operations and it is included in the national policy of some countries. In recognition of the importance of the subject, the IAEA has decided to review the current status of the work aimed at waste minimization in the nuclear fuel cycle. The waste minimization issues related to the back end of the nuclear fuel cycle are covered in Technical Reports Series No. 377 'Minimization of Radioactive Waste from Nuclear Power Plants and the Back End of the Nuclear Fuel Cycle' published in 1995. The present report deals with the front end of the nuclear fuel cycle, including existing options, approaches, developments and some specific considerations to be taken into account in decision making on waste minimization. It has been recognized that, in comparison with the back end of the nuclear fuel cycle, much less information is available, and this report should be considered as a first attempt to analyse waste minimization practices and opportunities in uranium purification, conversion, enrichment and fuel fabrication. Although mining and milling is an important part of the front end of the nuclear fuel cycle, these activities are excluded from consideration since relevant activities are covered in other IAEA publications.

Minimization of waste from uranium purification, enrichment and fuel fabrication

International Nuclear Information System (INIS)

1999-10-01

As any industry, nuclear industry generates a diverse range of waste which has to be managed in a safe manner to be acceptable to the public and the environment. The cost of waste management, the risks to the public and employees, and the detriment to the environment are dependent on the quantity and radioactive content of the waste generated. Waste minimization is a necessary activity needed to reduce the impact from nuclear fuel cycle operations and it is included in the national policy of some countries. In recognition of the importance of the subject, the IAEA has decided to review the current status of the work aimed at waste minimization in the nuclear fuel cycle. The waste minimization issues related to the back end of the nuclear fuel cycle are covered in Technical Reports Series No. 377 'Minimization of Radioactive Waste from Nuclear Power Plants and the Back End of the Nuclear Fuel Cycle' published in 1995. The present report deals with the front end of the nuclear fuel cycle, including existing options, approaches, developments and some specific considerations to be taken into account in decision making on waste minimization. It has been recognized that, in comparison with the back end of the nuclear fuel cycle, much less information is available, and this report should be considered as a first attempt to analyse waste minimization practices and opportunities in uranium purification, conversion, enrichment and fuel fabrication. Although mining and milling is an important part of the front end of the nuclear fuel cycle, these activities are excluded from consideration since relevant activities are covered in other IAEA publications

Adoption of waste minimization technology to benefit electroplaters

Energy Technology Data Exchange (ETDEWEB)

Ching, E.M.K.; Li, C.P.H.; Yu, C.M.K. [Hong Kong Productivity Council, Kowloon (Hong Kong)

1996-12-31

Because of increasingly stringent environmental legislation and enhanced environmental awareness, electroplaters in Hong Kong are paying more heed to protect the environment. To comply with the array of environmental controls, electroplaters can no longer rely solely on the end-of-pipe approach as a means for abating their pollution problems under the particular local industrial environment. The preferred approach is to adopt waste minimization measures that yield both economic and environmental benefits. This paper gives an overview of electroplating activities in Hong Kong, highlights their characteristics, and describes the pollution problems associated with conventional electroplating operations. The constraints of using pollution control measures to achieve regulatory compliance are also discussed. Examples and case studies are given on some low-cost waste minimization techniques readily available to electroplaters, including dragout minimization and water conservation techniques. Recommendations are given as to how electroplaters can adopt and exercise waste minimization techniques in their operations. 1 tab.

Prevention and minimization of waste production

International Nuclear Information System (INIS)

Noynaert, L.

1998-01-01

The main objective of the program Prevention and Minimization of Waste Production at the Belgian Nuclear Research Centre SCK/CEN is to contribute to reducing the volume and costs of nuclear waste. In addition, it aims to provide reliable data and models to the design engineers with a view to determining the final plant characteristics. Main activities in 1997 are described

Waste minimization activity report for 1991

International Nuclear Information System (INIS)

Shoemaker, J.D.

1992-01-01

This is a waste reduction report for the Lawrence Livermore National Laboratory (LLNL) for 1991. The report covers the Main Site at Livermore and Site 300. Each research program at LLNL is described by its operation, administrative procedures, and waste minimization. Examples of the programs at LLNL are biomedical and environmental research, chemistry and materials science, and energy program and earth sciences. (MB)

Using benchmarking to minimize common DOE waste streams: Volume 5. Office paper waste

Energy Technology Data Exchange (ETDEWEB)

Levin, V.

1995-10-01

Finding innovative ways to reduce waste streams generated at US Department of Energy (DOE) sites by 50% by the year 2000 is a challenge for DOE`s waste minimization efforts. A team composed of members from several DOE facilities used the quality tool known as benchmarking to improve waste minimization efforts. First the team examined office waste generation and handling processes at their sites. Then team members developed telephone and written questionnaires to help identify potential ``best-in-class`` industry partners willing to share information about their best waste minimization techniques and technologies. The team identified two benchmarking partners, NIKE, Inc., in Beaverton, Oregon, and Microsoft, Inc., in Redmond, Washington. Both companies have proactive, employee-driven environmental issues programs. Both companies report strong employee involvement, management commitment, and readily available markets for recyclable materials such as white paper and nonwhite assorted paper. The availability of markets, the initiative and cooperation of employees, and management support are the main enablers for their programs. At both companies, recycling and waste reduction programs often cut across traditional corporate divisions such as procurement, janitorial services, environmental compliance, grounds maintenance, cafeteria operations, surplus sales, and shipping and receiving. These companies exhibited good cooperation between these functions to design and implement recycling and waste reduction programs.

Using benchmarking to minimize common DOE waste streams: Volume 5. Office paper waste

International Nuclear Information System (INIS)

Levin, V.

1995-10-01

Finding innovative ways to reduce waste streams generated at US Department of Energy (DOE) sites by 50% by the year 2000 is a challenge for DOE's waste minimization efforts. A team composed of members from several DOE facilities used the quality tool known as benchmarking to improve waste minimization efforts. First the team examined office waste generation and handling processes at their sites. Then team members developed telephone and written questionnaires to help identify potential ''best-in-class'' industry partners willing to share information about their best waste minimization techniques and technologies. The team identified two benchmarking partners, NIKE, Inc., in Beaverton, Oregon, and Microsoft, Inc., in Redmond, Washington. Both companies have proactive, employee-driven environmental issues programs. Both companies report strong employee involvement, management commitment, and readily available markets for recyclable materials such as white paper and nonwhite assorted paper. The availability of markets, the initiative and cooperation of employees, and management support are the main enablers for their programs. At both companies, recycling and waste reduction programs often cut across traditional corporate divisions such as procurement, janitorial services, environmental compliance, grounds maintenance, cafeteria operations, surplus sales, and shipping and receiving. These companies exhibited good cooperation between these functions to design and implement recycling and waste reduction programs

An operational waste minimization chargeback system at Sandia National Laboratories, New Mexico

International Nuclear Information System (INIS)

Horak, K.; Peek, D.W.; Stermer, D.; Dailleboust, L.; Reilly, H.

1993-01-01

Sandia National Laboratories, New Mexico, (SNL/NM) has made a commitment to achieve significant reductions in the amount of hazardous wastes generated throughout its operations. The success of the SNL/NM Waste Minimization/Pollution Prevention Program depends primarily on: (1) adequate program funding, and (2) comprehensive collection and dissemination of information pertaining to SNL/NM's waste. This paper describes the chargeback system that SNL/NM has chosen for funding the implementation of the Waste Minimization/Pollution Prevention program, as well as the waste reporting system that follows naturally from the chargeback system. Both the chargeback and reporting systems have been fully implemented. The details of implementation are discussed, including: the physical means by which waste is managed and data collected; the database systems which have been linked; the flow of data through both human hands and electronic systems; the quality assurance of that data; and the waste report format now in use. Also discussed are intended improvements in the system that are currently planned for the coming years

An analysis of radioactive waste minimization efforts at Los Alamos National Laboratory

Energy Technology Data Exchange (ETDEWEB)

Voit, S.L.; Boerigter, S.T.

1997-09-30

LANL will be the primary DOE facility for plutonium research and development and plutonium processing. A summary of the currently generated waste types, volumes, generating facilities or programs, and disposal costs are given in this report along with future waste generation projections. Several key existing technologies have been identified that could be introduced to reduce the generated waste at LANL. Four of these are discussed in detail in this report: (1) electrolytic surface decontamination, (2) electrochemical treatment of mixed wastes, (3) Long Range Alpha Detection (LRAD), and (4) Segmented Gate and Containerized Vat Leach System (SGS/CVL). These technologies may be implemented as modifications in upstream processes as well as more efficient volume reduction and segregation. The four technologies are mature enough to be implemented in the next two to three years and can be done so with the support for capital and operational costs. Also discussed in this report is a small sample of some of the recent waste minimization success stories that have been implemented. Several technologies are presented that are either currently being investigated or on hold due to lack of funding at LANL but show potential for making significant gains in waste minimization. This report is intended to provide a review of the waste minimization issues and analysis of the impact of implementing a few of these technologies.

An analysis of radioactive waste minimization efforts at Los Alamos National Laboratory

International Nuclear Information System (INIS)

Voit, S.L.; Boerigter, S.T.

1997-01-01

LANL will be the primary DOE facility for plutonium research and development and plutonium processing. A summary of the currently generated waste types, volumes, generating facilities or programs, and disposal costs are given in this report along with future waste generation projections. Several key existing technologies have been identified that could be introduced to reduce the generated waste at LANL. Four of these are discussed in detail in this report: (1) electrolytic surface decontamination, (2) electrochemical treatment of mixed wastes, (3) Long Range Alpha Detection (LRAD), and (4) Segmented Gate and Containerized Vat Leach System (SGS/CVL). These technologies may be implemented as modifications in upstream processes as well as more efficient volume reduction and segregation. The four technologies are mature enough to be implemented in the next two to three years and can be done so with the support for capital and operational costs. Also discussed in this report is a small sample of some of the recent waste minimization success stories that have been implemented. Several technologies are presented that are either currently being investigated or on hold due to lack of funding at LANL but show potential for making significant gains in waste minimization. This report is intended to provide a review of the waste minimization issues and analysis of the impact of implementing a few of these technologies

Environmental Restoration Contractor Waste Minimization and Pollution Prevention Plan

International Nuclear Information System (INIS)

Lewis, R.A.

1994-11-01

The purpose of this plan is to establish the Environmental Restoration Contractor (ERC) Waste Minimization and Pollution Prevention (WMin/P2) Program and outline the activities and schedules that will be employed to reduce the quantity and toxicity of wastes generated as a result of restoration and remediation activities. It is intended to satisfy the US Department of Energy (DOE) and other legal requirements. As such, the Pollution Prevention Awareness program required by DOE Order 5400.1 is included with the Pollution Prevention Program. This plan is also intended to aid projects in meeting and documenting compliance with the various requirements for WMin/P2, and contains the policy, objectives, strategy, and support activities of the WMin/P2 program. The basic elements of the plan are pollution prevention goals, waste assessments of major waste streams, implementation of feasible waste minimization opportunities, and a process for reporting achievements. Various pollution prevention techniques will be implemented with the support of employee training and awareness programs to reduce waste and still meet applicable requirements. Information about the Hanford Site is in the Hanford Site Waste Minimization and Pollution Prevention Awareness Program Plan

The waste minimization program at the Feed Materials Production Center

International Nuclear Information System (INIS)

Blasdel, J.E.; Crotzer, M.E.; Gardner, R.L.; Kato, T.R.; Spradlin, C.N.

1987-01-01

A waste minimization program is being implemented at the Feed Materials Production Center to reduce the generation of uranium-contaminated wastes and to comply with existing and forthcoming regulations. Procedures and plans are described which deal with process and non-process trash, contaminated wood and metals, used metal drums, and major process wastes such as contaminated magnesium fluoride and neutralized raffinate. Waste minimization techniques used include segregation, source reduction, volume reduction, material substitution and waste/product recycle. The importance of training, communication, and incentives is also covered. 5 refs., 11 figs

Proceedings of the Department of Energy Defense Programs hazardous and mixed waste minimization workshop: Hazardous Waste Remedial Actions Program

International Nuclear Information System (INIS)

1988-09-01

The first workshop on hazardous and mixed waste minimization was held in Las Vegas, Nevada, on July 26--28, 1988. The objective of this workshop was to establish an interchange between DOE headquarters (DOE-HQ) DP, Operations Offices, and contractors of waste minimization strategies and successes. The first day of the workshop began with presentations stressing the importance of establishing a waste minimization program at each site as required by RCRA, the land ban restrictions, and the decrease in potential liabilities associated with waste disposal. Discussions were also centered on pending legislation which would create an Office of Waste Reduction in the Environmental Protection Agency (EPA). The Waste Minimization and Avoidance Study was initiated by DOE as an addition to the long-term productivity study to address the issues of evolving requirements facing RCRA waste management activities at the DP sites, to determine how major operations will be affected by these requirements, and to determine the available strategies and options for waste minimization and avoidance. Waste minimization was defined in this study as source reduction and recycling

Prevention and Minimization of Waste Production

International Nuclear Information System (INIS)

Noynaert, L.; Bruggeman, A.; Rahier, A.

1998-01-01

The general objectives of SCK-CEN's programme on the prevention and minimization of waste production are to contribute to reducing volumes and cost of radioactive waste. It also aims tro provide reliable data and models to the design engineers with a view to determining the final plant characteristics. In the long term, these objectives will be extended to other nuclear applications. Progress and achievements in 1997 are summarised

Advanced Purex process and waste minimization at La Hague

International Nuclear Information System (INIS)

Masson, H.; Nouguier, H.; Bernard, C.; Runge, S.

1993-01-01

After a brief recall of the different aspects of the commercial irradiated fuel reprocessing, this paper presents the achievements of the recently commissioned UP3 plant at La Hague. The advanced Purex process implemented with a total waste management results in important waste volume minimization, so that the total volume of high-level and transuranic waste is lower than what it would be in a once-through cycle. Moreover, further minimization is still possible, based on an improved waste management. Cogema has launched the necessary program, which will lead to an overall volume of HLW and TRU wastes of less than 1 m 3 /t by the end of the decade, the maximum possible activity being concentrated in the glass

Waste Minimization/Pollution Prevention Crosscut Plan, 1994

International Nuclear Information System (INIS)

1994-01-01

This plan establishes a Department-wide goal to reduce total releases of toxic chemicals to the environment and off-site transfers of such toxic chemicals by 50 percent by December 31, 1999, in compliance with Executive Order 12856. Each site that meets the threshold quantities of toxic chemicals established in the Emergency Planning and Community Right-to-Know Act (EPCRA) will participate in this goal. In addition, each DOE site will establish site-specific goals to reduce generation of hazardous, radioactive, radioactive mixed, and sanitary wastes and pollutants, as applicable. Implementation of this plan will represent a major step toward the environmental risks and costs associated with DOE operations and increasing the Department's use of preventive environmental management practices. Investing in Waste Minimization Pollution Prevention (WMin/PP) steadily reduce hazardous and radioactive waste generation and will reduce the need for waste management and unnecessary expenditures for waste treatment, storage, and disposal. A preventive approach to waste management will help solve current environmental and regulatory issues and reduce the need for costly future corrective actions. The purpose of this plan is to establish the strategic framework for integrating WMin/PP into all DOE internal activities. This program includes setting DOE policy and goals for reducing the generation of wastes and pollutants, increasing recycling activities, and establishing an infrastructure to achieve and measure the goals throughout the DOE complex. Waste Minimization and Pollution Prevention Awareness Plans, submitted to Headquarters by DOE field sites, will incorporate the WMin/PP activities and goals outlined in this plan. Success of the DOE WMin/PP program is dependent upon each field operation becoming accountable for resources used, wastes and pollutants generated, and wastes recycled

Waste minimization fundamental principles used in radioactive waste management plan for decommissioning of a CANDU - 600 nuclear power plant

International Nuclear Information System (INIS)

Barariu, Gheorghe; Georgescu, Roxana Cristiana; Sociu, Florin

2009-01-01

The objectives of waste minimization are to limit the generation and spread of radioactive contamination and to reduce the amount of wastes for storage and disposal, thereby limiting any consequent environmental impact, as well as the total costs associated with contaminated material management. This objective will be achieved by: reviewing the sources and characteristics of radioactive materials arising from Decontamination and Decommissioning (D and D) activities; reviewing waste minimization principles and current practical applications, together with regulatory, technical, financial and political factors influencing waste minimization practices; and reviewing current trends in improving waste minimization practices during Decontamination and Decommissioning. The main elements of a waste minimization strategy can be grouped into four areas: source reduction, prevention of contamination spread, recycle and reuse, and waste management optimization. For sustaining this objective, the following principles and procedures of wastes management are taken into account: safety and environment protection principles; principles regarding the facility operation; quality assurance procedures; procedures for material classification and releasing. (authors)

Development and pilot demonstration program of a waste minimization plan at Argonne National Laboratory

International Nuclear Information System (INIS)

Peters, R.W.; Wentz, C.A.; Thuot, J.R.

1991-01-01

In response to US Department of Energy directives, Argonne National Laboratory (ANL) has developed a waste minimization plan aimed at reducing the amount of wastes at this national research and development laboratory. Activities at ANL are primarily research- oriented and as such affect the amount and type of source reduction that can be achieved at this facility. The objective of ANL's waste minimization program is to cost-effectively reduce all types of wastes, including hazardous, mixed, radioactive, and nonhazardous wastes. The ANL Waste Minimization Plan uses a waste minimization audit as a systematic procedure to determine opportunities to reduce or eliminate waste. To facilitate these audits, a computerized bar-coding procedure is being implemented at ANL to track hazardous wastes from where they are generated to their ultimate disposal. This paper describes the development of the ANL Waste Minimization Plan and a pilot demonstration of the how the ANL Plan audited the hazardous waste generated within a selected divisions of ANL. It includes quantitative data on the generation and disposal of hazardous waste at ANL and describes potential ways to minimize hazardous wastes. 2 refs., 5 figs., 8 tabs

Waste minimization successes at McGuire Nuclear Station

International Nuclear Information System (INIS)

Correll, J.C.; Johnson, G.T.

1995-01-01

McGuire Nuclear Station is a two unit, 1125 MWe PWR located 25 miles north of Charlotte, North Carolina. It is a Westinghouse Ice Condenser plant that is owned and operated by Duke Power Company. At Duke Power, open-quotes Culture Changeclose quotes is a common term that we have used to describe the incredible transformation that we are making to become a cost conscious, customer driven, highly competitive business. Nowhere has this change been more evident then in the way we process and disposed of our solid radioactive waste. With top-down management support, we have used team-based, formalized, problem solving methods and have implemented many successful waste minimization programs. Through these programs, we have dramatically increased employees close-quote awareness of the importance of waste minimization. As a result, we have been able to reduce both our burial volumes and our waste processing and disposal costs

Methods for the minimization of radioactive waste from decontamination and decommissioning of nuclear facilities

International Nuclear Information System (INIS)

2001-01-01

The objective of this report is to provide Member States and their decision makers (ranging from regulators, strategists, planners and designers, to operators) with relevant information on opportunities for minimizing radioactive wastes arising from the D and D of nuclear facilities. This will allow waste minimization options to be properly planned and assessed as part of national, site and plant waste management policies. This objective will be achieved by: reviewing the sources and characteristics of radioactive materials arising from D and D activities; reviewing waste minimization principles and current practical applications, together with regulatory, technical, financial and political factors influencing waste minimization practices; and reviewing current trends in improving waste minimization practices during D and D

Waste minimization for land-based drilling operations

International Nuclear Information System (INIS)

Thurber, N.E.

1992-01-01

This paper discusses engineering variables that should be addressed to minimize waste-toxicity and generation while drilling land-based wells. Proper balance of these variables provides both operational and environmental benefits

WASTE MINIMIZATION ASSESSMENT FOR A MANUFACTURER OF CUSTOM MOLDED PLASTIC PRODUCTS

Science.gov (United States)

The U.S. Environmental Protection Agency (EPA) has funded a pilot project to assist small- and medium-size manufacturers who want to minimize their generation of waste but who lack the expertise to do so. Waste Minimization Assessment Centers (WMACs) were established at selected ...

Annual Waste Minimization Summary Report, Calendar Year 2008

International Nuclear Information System (INIS)

2009-01-01

This report summarizes the waste minimization efforts undertaken by National Security Technologies, LLC (NSTec), for the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office (NNSA/NSO), during calendar year 2008. This report was developed in accordance with the requirements of the Nevada Test Site (NTS) Resource Conservation and Recovery Act (RCRA) Permit (No. NEV HW0021), and as clarified in a letter dated April 21, 1995, from Paul Liebendorfer of the Nevada Division of Environmental Protection to Donald Elle of the U.S. Department of Energy, Nevada Operations Office. The NNSA/NSO Pollution Prevention (P2) Program establishes a process to reduce the volume and toxicity of waste generated by NNSA/NSO activities and ensures that proposed methods of treatment, storage, and/or disposal of waste minimize potential threats to human health and the environment. The following information provides an overview of the P2 Program, major P2 accomplishments during the reporting year, a comparison of the current year waste generation to prior years, and a description of efforts undertaken during the year to reduce the volume and toxicity of waste generated by the NNSA/NSO

Annual Waste Minimization Summary Report, Calendar Year 2009

International Nuclear Information System (INIS)

2010-01-01

This report summarizes the waste minimization efforts undertaken by National Security Technologies, LLC, for the U. S. Department of Energy, National Nuclear Security Administration Nevada Site Office (NNSA/NSO), during calendar year 2009. This report was developed in accordance with the requirements of the Nevada Test Site Resource Conservation and Recovery Act Permit (No. NEV HW0021), and as clarified in a letter dated April 21, 1995, from Paul Liebendorfer of the Nevada Division of Environmental Protection to Donald Elle of the U.S. Department of Energy, Nevada Operations Office. The NNSA/NSO Pollution Prevention (P2) Program establishes a process to reduce the volume and toxicity of waste generated by NNSA/NSO activities and ensures that proposed methods of treatment, storage, and/or disposal of waste minimize potential threats to human health and the environment. The following information provides an overview of the P2 Program, major P2 accomplishments during the reporting year, a comparison of the current year waste generation to prior years, and a description of efforts undertaken during the year to reduce the volume and toxicity of waste generated by NNSA/NSO.

Annual Waste Minimization Summary Report Calendar Year 2007

International Nuclear Information System (INIS)

NSTec Environmental Management

2008-01-01

This report summarizes the waste minimization efforts undertaken by National Security Technologies, LLC (NSTec), for the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office (NNSA/NSO), during calendar year (CY) 2007. This report was developed in accordance with the requirements of the Nevada Test Site (NTS) Resource Conservation and Recovery Act (RCRA) Permit (number NEV HW0021), and as clarified in a letter dated April 21, 1995, from Paul Liebendorfer of the Nevada Division of Environmental Protection to Donald Elle of the U.S. Department of Energy, Nevada Operations Office. The NNSA/NSO Pollution Prevention (P2) Program establishes a process to reduce the volume and toxicity of waste generated by the NNSA/NSO and ensures that proposed methods of treatment, storage, and/or disposal of waste minimize potential threats to human health and the environment. The following information provides an overview of the P2 Program, major P2 accomplishments during the reporting year, a comparison of the current year waste generation to prior years, and a description of efforts undertaken during the year to reduce the volume and toxicity of waste generated by the NNSA/NSO

WASTE MINIMIZATION ASSESSMENT FOR A MANUFACTURER OF CUTTING AND WELDING EQUIPMENT

Science.gov (United States)

The U.S. Environmental Protection Agency (EPA) has funded a pilot program to assist small and medium-size manufacturers who want to minimize their generation of waste but who lack the expertise to do so in an effort to assist these manufacturers Waste Minimization Assessment Cent...

Hanford Site waste minimization and pollution prevention awareness program plan

International Nuclear Information System (INIS)

1994-05-01

The Hanford Site WMin/P2 program is an organized, comprehensive, and continual effort to systematically reduce the quantity and toxicity of hazardous, radioactive, mixed, and sanitary wastes; conserve resources; and prevent or minimize pollutant releases to all environmental media from all Site activities. The Hanford Site WMin/P2 program plan reflects national and DOE waste minimization and pollution prevention goals and policies, and represents an ongoing effort to make WMin/P2 part of the Site operating philosophy. In accordance with these policies, a hierarchical approach to environmental management has been adopted and is applied to all types of polluting and waste generating activities. Pollution prevention and waste minimization through source reduction are first priority in the Hanford WMin/P2 program, followed by environmentally safe recycling. Treatment to reduce the quantity, toxicity, and/or mobility will be considered only when prevention or recycling are not possible or practical. Environmentally safe disposal is the last option

Minimization of rad waste production in NPP Dukovany

International Nuclear Information System (INIS)

Kulovany, J.

2001-01-01

A whole range of measures has been taken in the power plant in connection with the minimization of radioactive waste. It will lead to the set goals. The procedures that prevent possible endangering of the operation take precedence during introduction of the minimization measures. Further economically undemanding procedures are implemented that bring about minimization in an effective way. In accordance with the EMS principles it can be expected that the minimizing measures will be implemented also in areas where their greatest contribution will be for the environment

Significance of chemotoxic admixtures in radioactive wastes

International Nuclear Information System (INIS)

Merz, E.R.

1989-01-01

The double hazard potential of mixed wastes is characterized by several criteria: radioactivity on the one hand, and chemical toxicity, in flammability, corrosiveness as well as chemical reactivity on the other. The author argues that mixed wastes assigned for ultimate disposal should therefore be thoroughly detoxified, inertized, or mineralized, prior to conditioning and packaging. Strategies and techniques are presented which ensure the elimination of hazardous organic chemicals and minimizing waste volumes to be disposed of. Advantage can be taken of mixing mineralized filter dusts, arising in the combustion of hazardous chemical wastes with low-activity inertized radioactive wastes as a solidifying reagent. Simultaneous geological disposal of such mixed waste is feasible without any drawbacks

Waste minimization for land-based drilling operations

International Nuclear Information System (INIS)

Thurber, N.E.

1991-01-01

This paper discusses many of the engineering variables that should be addressed to minimize waste toxicity and generation during the drilling of land-based wells. Proper balance of these variables suggests both operational and environmental benefits

Waste minimization/pollution prevention at R ampersand D facilities: Implementing the SNL/NM Process Waste Assessment Program

International Nuclear Information System (INIS)

Kjeldgaard, E.A.; Stermer, D.L.; Saloio, J.H. Jr.; Lorton, G.A.

1993-01-01

The Sandia National Laboratories, New Mexico (SNL/NM) Process Waste Assessment (PWA) program began formally on November 2, 1992. This program represents the first laboratory-wide attempt to explicitly identify and characterize SNL/NM's waste generating processes for waste minimization purposes. This paper describes the major elements of the SNL/NM PWA program, the underlying philosophy for designing a PWA program at a highly diverse laboratory setting such as SNL/NM, and the experiences and insights gained from five months of implementing this living program. Specifically, the SNL/NM PWA program consists of four major, interrelated phases: (1) Process Definition, (2) Process Characterization, (3) Waste Minimization Opportunity Assessment, and (4) Project Evaluation, Selection, Implementation, and Tracking. This phased approach was developed to Provide a flexible, yet appropriate, level of detail to the multitude of different ''processes'' at SNL/NM. Using a staff infrastructure of approximately 60 Waste Minimization Network Representatives (MinNet Reps) and consulting support, the SNL/NM PWA program has become the linchpin of even more progressive and proactive environmental, safety, and health (ES ampersand H) initiatives such as: (1) cradle-to-grove material/waste tracking, (2) centralized ES ampersand H reporting, and (3) detailed baselining and tracking for measuring multi-media waste reduction goals. Specific examples from the SNL/NM PWA program are provided, including the results from Process Definition, Process Characterization, and Waste Minimization Opportunity Assessments performed for a typical SNL/NM process

Health Physics and Waste Minimization Best Practices benchmarking study

International Nuclear Information System (INIS)

Levin, V.

1995-01-01

The Health Physics and Waste Minimization Best Practices project examines the usefulness of benchmarking as a tool for identifying health physics and waste minimization best practices for low-level solid radioactive waste (LLW) in the U.S. Department of Energy (DOE) complex. The goal of the project is to identify best practices from the nuclear power industry that will reduce the amount of LLW going to disposal in a cost-effective manner. An increase in worker efficiency and productivity is a secondary goal. These practices must be adaptable for implementation in the DOE complex. Once best practices are identified, ranked, and funded for implementation, a pilot implementation will be done at the Chemistry and Metallurgy Research (CMR) building at Los Alamos National Laboratory

A case-study of landfill minimization and material recovery via waste co-gasification in a new waste management scheme.

Science.gov (United States)

Tanigaki, Nobuhiro; Ishida, Yoshihiro; Osada, Morihiro

2015-03-01

This study evaluates municipal solid waste co-gasification technology and a new solid waste management scheme, which can minimize final landfill amounts and maximize material recycled from waste. This new scheme is considered for a region where bottom ash and incombustibles are landfilled or not allowed to be recycled due to their toxic heavy metal concentration. Waste is processed with incombustible residues and an incineration bottom ash discharged from existent conventional incinerators, using a gasification and melting technology (the Direct Melting System). The inert materials, contained in municipal solid waste, incombustibles and bottom ash, are recycled as slag and metal in this process as well as energy recovery. Based on this new waste management scheme with a co-gasification system, a case study of municipal solid waste co-gasification was evaluated and compared with other technical solutions, such as conventional incineration, incineration with an ash melting facility under certain boundary conditions. From a technical point of view, co-gasification produced high quality slag with few harmful heavy metals, which was recycled completely without requiring any further post-treatment such as aging. As a consequence, the co-gasification system had an economical advantage over other systems because of its material recovery and minimization of the final landfill amount. Sensitivity analyses of landfill cost, power price and inert materials in waste were also conducted. The higher the landfill costs, the greater the advantage of the co-gasification system has. The co-gasification was beneficial for landfill cost in the range of 80 Euro per ton or more. Higher power prices led to lower operation cost in each case. The inert contents in processed waste had a significant influence on the operating cost. These results indicate that co-gasification of bottom ash and incombustibles with municipal solid waste contributes to minimizing the final landfill amount and has

Low-level radioactive waste minimization for health care institutions

International Nuclear Information System (INIS)

Williams, G.

1990-01-01

In recent years medical waste has been the subject of considerable public and governmental attention. This has been, in part, due to the media's attraction to unfortunate instances of environmental pollution caused by hazardous and medical wastes. While a considerable amount of information is currently available on the treatment and disposal practices for hazardous wastes, a shortfall of information exists on the subject of medical wastes. Such wastes are generated by various health care institutions. Medical waste is a wide and all encompassing term which refers to a variety of wastes. This presentation addresses medical low-level (LLW) radioactive waste; its generation, recovery and handling. The development of generic waste minimization models and greater use of alternative technologies are part of the discussion

Hazardous waste minimization report for CY 1986

International Nuclear Information System (INIS)

Kendrick, C.M.

1990-12-01

Oak Ridge National Laboratory (ORNL) is a multipurpose research and development facility. Its primary role is the support of energy technology through applied research and engineering development and scientific research in basic and physical sciences. ORNL also is a valuable resource in the solution of problems of national importance, such as nuclear and chemical waste management. In addition, useful radioactive and stable isotopes which are unavailable from the private sector are produced at ORNL. As a result of these activities, hazardous, radioactive, and mixed wastes are generated at ORNL. A formal hazardous waste minimization program for ORNL was launched in mid 1985 in response to the requirements of Section 3002 of the Resource Conservation and Recovery Act (RCRA). During 1986, a task plan was developed. The six major tasks include: planning and implementation of a laboratory-wide chemical inventory and the subsequent distribution, treatment, storage, and/or disposal (TSD) of unneeded chemicals; establishment and implementation of a distribution system for surplus chemicals to other (internal and external) organizations; training and communication functions necessary to inform and motivate laboratory personnel; evaluation of current procurement and tracking systems for hazardous materials and recommendation and implementation of improvements; systematic review of applicable current and proposed ORNL procedures and ongoing and proposed activities for waste volume and/or toxicity reduction potential; and establishment of criteria by which to measure progress and reporting of significant achievements. 8 refs., 1 fig., 5 tabs

Headquarters Air Force Logistics Command guidance manual for hazardous waste minimization (PACER REDUCE): Hazardous Waste Remedial Actions Program

International Nuclear Information System (INIS)

Jones, L.W.; Weeter, D.; Roth, J.A.; Debelak, K.A.; Bowers, A.R.

1988-09-01

This manual provides guidance for the Air Force Logistics Command (AFLC) Waste Minimization Program, called PACER REDUCE, and applies to all AFLC installations and personel who are responsible for implementing and monitoring activities relating to PACER REDUCE. This guidance for waste minimization provides management and technical approaches for assessing potential waste reduction techniques and for making informed decisions concerning industrial process and waste stream management. Such actions will assist in achieving regulatory compliance with the Resource Conservation and Recovery Act of 1976 as updated by the Hazardous and Solid Waste Amendments of 1984. 37 refs., 14 figs., 22 tabs

Cost/benefit analysis for selected waste minimization technologies at TA-55

International Nuclear Information System (INIS)

Boerigter, S.T.

1996-01-01

The TA-55 plutonium facility at LANL is one of the remaining plutonium-handling facilities in the United States with significant operational capability. In recent years a great deal of attention has been focused on the waste streams generated by this facility. Costs of properly treating these streams have risen significantly. This paper discusses the characterization of several proposed radioactive waste minimization technologies as a function of Return on Investment (ROI). In particular, the DOE Environmental Management program has identified a specific funding channel for such technology development activities, but this funding channel requires a restrictive definition of ROI. Here, a simple extension to the required ROI equation is used to capture the lifecycle ROI due to offsets in future capital charges resulting from present spending

Molten salt treatment to minimize and optimize waste

International Nuclear Information System (INIS)

Gat, U.; Crosley, S.M.; Gay, R.L.

1993-01-01

A combination molten salt oxidizer (MSO) and molten salt reactor (MSR) is described for treatment of waste. The MSO is proposed for contained oxidization of organic hazardous waste, for reduction of mass and volume of dilute waste by evaporation of the water. The NTSO residue is to be treated to optimize the waste in terms of its composition, chemical form, mixture, concentration, encapsulation, shape, size, and configuration. Accumulations and storage are minimized, shipments are sized for low risk. Actinides, fissile material, and long-lived isotopes are separated and completely burned or transmuted in an MSR. The MSR requires no fuel element fabrication, accepts the materials as salts in arbitrarily small quantities enhancing safety, security, and overall acceptability

Waste minimization and pollution prevention awareness plan. Revision 1

International Nuclear Information System (INIS)

1994-07-01

The purpose of this plan is to document Lawrence Livermore National Laboratory (LLNL) projections for present and future waste minimization and pollution prevention. The plan specifies those activities and methods that are or will be used to reduce the quantity and toxicity of wastes generated at the site. It is intended to satisfy Department of Energy (DOE) requirements. This Waste Minimization and Pollution Prevention Awareness Plan provides an overview of projected activities from FY 1994 through FY 1999. The plans are broken into site-wide and problem-specific activities. All directorates at LLNL have had an opportunity to contribute input, estimate budgets, and review the plan. In addition to the above, this plan records LLNL's goals for pollution prevention, regulatory drivers for those activities, assumptions on which the cost estimates are based, analyses of the strengths of the projects, and the barriers to increasing pollution prevention activities

Low-level waste minimization at the Y-12 Plant

Energy Technology Data Exchange (ETDEWEB)

Koger, J. [Oak Ridge National Lab., TN (United States)

1993-03-01

The Y-12 Development Waste Minimization Program is used as a basis for defining new technologies and processes that produce minimum low-level wastes (hazardous, mixed, radioactive, and industrial) for the Y-12 Plant in the future and for Complex-21 and that aid in decontamination and decommissioning (D and D) efforts throughout the complex. In the past, the strategy at the Y-12 Plant was to treat the residues from the production processes using chemical treatment, incineration, compaction, and other technologies, which often generated copious quantities of additional wastes and, with the exception of highly valuable materials such as enriched uranium, incorporated very little recycle in the process. Recycle, in this context, is defined as material that is put back into the process before it enters a waste stream. Additionally, there are several new technology drivers that have recently emerged with the changing climate in the Nuclear Weapons Complex such as Complex 21 and D and D technologies and an increasing number of disassemblies. The hierarchies of concern in the waste minimization effort are source reduction, recycle capability, treatment simplicity, and final disposal difficulty with regard to Complex 21, disassembly efforts, D and D, and, to a lesser extent, weapons production. Source reduction can be achieved through substitution of hazardous substances for nonhazardous materials, and process changes that result in less generated waste.

ENVIRONMENTAL RESEARCH BRIEF: WASTE MINIMIZATION ASSESSMENT FOR A MANUFACTURER OF PRINTED PLASTIC BAGS

Science.gov (United States)

The U.S. Environmental Protection Agency (EPA) has funded a pilot project to assist small- and medium-size manufacturers who want to minimize their generation of hazardous waste but who lack the expertise to do so. Waste Minimization Assessment Centers (WMACs) were established ...

ENVIRONMENTAL RESEARCH BRIEF: WASTE MINIMIZATION FOR A MANUFACTURER OF COMPRESSED AIR EQUIPMENT COMPONENTS

Science.gov (United States)

The U.S. Environmental Protection Agency (EPA) has funded a pilot project to assist small- and medium-size manufacturers who want to minimize their generation of hazardous waste but lack the expertise to do so. Waste Minimization Assessment Centers (WMACs) were established at sel...

WASTE MINIMIZATION ASSESSMENT FOR A MANUFACTURER OF SILICON-CONTROLLED RECTIFIERS AND SCHOTTKY RECTIFIERS

Science.gov (United States)

The U.S. Environmental Protection Agency (EPA) has funded a pilot project to assist small- and medium-size manufacturers who want to minimize their generation of waste but who lack the expertise to do so. In an effort to assist these manufacturers Waste Minimization Assessment Ce...

Waste Minimization via Radiological Hazard Reduction

International Nuclear Information System (INIS)

Stone, K.A.; Coffield, T.; Hooker, K.L.

1998-01-01

The Savannah River Site (SRS), a 803 km 2 U.S. Department of Energy (DOE) facility in south-western South Carolina, incorporates pollution prevention as a fundamental component of its Environmental Management System. A comprehensive pollution prevention program was implemented as part of an overall business strategy to reduce waste generation and pollution releases, minimize environmental impacts, and to reduce future waste management and pollution control costs. In fiscal years 1995 through 1997, the Site focused on implementing specific waste reduction initiatives identified while benchmarking industry best practices. These efforts resulted in greater than $25 million in documented cost avoidance. While these results have been dramatic to date, the Site is further challenged to maximize resource utilization and deploy new technologies and practices to achieve further waste reductions. The Site has elected to target a site-wide reduction of contaminated work spaces in fiscal year 1998 as the primary source reduction initiative. Over 120,900 m 2 of radiologically contaminated work areas (approximately 600 separate inside areas) exist at SRS. Reduction of these areas reduces future waste generation, minimizes worker exposure, and reduces surveillance and maintenance costs. This is a major focus of the Site's As Low As Reasonably Achievable (ALARA) program by reducing sources of worker exposure. The basis for this approach was demonstrated during 1997 as part of a successful Enhanced Work Planning pilot conducted at several specific contamination areas at SRS. An economic-based prioritization process was utilized to develop a model for prioritizing areas to reclaim. In the H-Canyon Separation facility, over 3,900 m 2 of potentially contaminated area was rolled back to a Radiation Buffer Area. The facility estimated nearly 420 m 3 of low level radioactive waste will be avoided each year, and overall cost savings and productivity gains will reach approximately $1

A case-study of landfill minimization and material recovery via waste co-gasification in a new waste management scheme

Energy Technology Data Exchange (ETDEWEB)

Tanigaki, Nobuhiro, E-mail: tanigaki.nobuhiro@eng.nssmc.com [NIPPON STEEL & SUMIKIN ENGINEERING CO., LTD., (EUROPEAN OFFICE), Am Seestern 8, 40547 Dusseldorf (Germany); Ishida, Yoshihiro [NIPPON STEEL & SUMIKIN ENGINEERING CO., LTD., 46-59, Nakabaru, Tobata-ku, Kitakyushu, Fukuoka 804-8505 (Japan); Osada, Morihiro [NIPPON STEEL & SUMIKIN ENGINEERING CO., LTD., (Head Office), Osaki Center Building 1-5-1, Osaki, Shinagawa-ku, Tokyo 141-8604 (Japan)

2015-03-15

advantage of the co-gasification system has. The co-gasification was beneficial for landfill cost in the range of 80 Euro per ton or more. Higher power prices led to lower operation cost in each case. The inert contents in processed waste had a significant influence on the operating cost. These results indicate that co-gasification of bottom ash and incombustibles with municipal solid waste contributes to minimizing the final landfill amount and has great possibilities maximizing material recovery and energy recovery from waste.

Hazardous waste minimization at Oak Ridge National Laboratory during 1987

International Nuclear Information System (INIS)

Kendrick, C.M.

1988-03-01

Oak Ridge National Laboratory (ORNL) is a multipurpose research and development facility owned and operated by the Department of Energy (DOE) and managed under subcontract by Martin Marietta Energy Systems, Inc. Its primary role is the support of energy technology through applied research and engineering development and scientific research in basic and physical sciences. ORNL also is a valuable resource in the solution of problems of national importance, such as nuclear and chemical waste management. In addition, useful radioactive and stable isotopes which are unavailable from the private sector are produced at ORNL. A formal hazardous waste minimization program for ORNL was launched in mid-1985 in response to the requirements of Section 3002 of the Resource Conservation and Recovery Act (RCRA). The plan for waste minimization has been modified several times and continues to be dynamic. During 1986, a task plan was developed. The six major tasks include: planning and implementation of a laboratory-wide chemical inventory and the subsequent distribution, treatment, storage, and/or disposal (TSD) of unneeded chemicals; establishment and implementation of a system for distributing surplus chemicals to other (internal and external) organizations; training and communication functions necessary to inform and motivate laboratory personnel; evaluation of current procurement and tracking systems for hazardous materials and recommendation and implementation of improvements; systematic review of applicable current and proposed ORNL procedures and ongoing and proposed activities for waste volume and/or toxicity reduction potential; and establishment of criteria by which to measure progress and reporting of significant achievements. Progress is being made toward completing these tasks and is described in this report. 13 refs., 1 fig., 7 tabs

Waste minimization in analytical chemistry through innovative sample preparation techniques

International Nuclear Information System (INIS)

Smith, L. L.

1998-01-01

Because toxic solvents and other hazardous materials are commonly used in analytical methods, characterization procedures result in significant and costly amount of waste. We are developing alternative analytical methods in the radiological and organic areas to reduce the volume or form of the hazardous waste produced during sample analysis. For the radiological area, we have examined high-pressure, closed-vessel microwave digestion as a way to minimize waste from sample preparation operations. Heated solutions of strong mineral acids can be avoided for sample digestion by using the microwave approach. Because reactivity increases with pressure, we examined the use of less hazardous solvents to leach selected contaminants from soil for subsequent analysis. We demonstrated the feasibility of this approach by extracting plutonium from a NET reference material using citric and tartaric acids with microwave digestion. Analytical results were comparable to traditional digestion methods, while hazardous waste was reduced by a factor often. We also evaluated the suitability of other natural acids, determined the extraction performance on a wider variety of soil types, and examined the extraction efficiency of other contaminants. For the organic area, we examined ways to minimize the wastes associated with the determination of polychlorinated biphenyls (PCBs) in environmental samples. Conventional methods for analyzing semivolatile organic compounds are labor intensive and require copious amounts of hazardous solvents. For soil and sediment samples, we have a method to analyze PCBs that is based on microscale extraction using benign solvents (e.g., water or hexane). The extraction is performed at elevated temperatures in stainless steel cells containing the sample and solvent. Gas chromatography-mass spectrometry (GC/MS) was used to quantitate the analytes in the isolated extract. More recently, we developed a method utilizing solid-phase microextraction (SPME) for natural

Development of a waste minimization plan for the Department of Energy's Naval petroleum reserve No. 3

International Nuclear Information System (INIS)

Falconer, K.L.; Lane, T.C.

1991-01-01

A Waste Minimization Program Plan for the U.S. Department of Energy's (DOE) Naval Petroleum Reserve No. 3 (NPR-3) was prepared in response to DOE Order 5400.1, open-quotes General Environmental Protection Program close-quote The NPR-3 Waste Minimization Program Plan encompasses all ongoing operations at the Naval Petroleum Reserve and is consistent with the principles set forth in the mission statement for NPR-3. The mission of the NPR-3 is to apply project management, engineering and scientific capabilities to produce oil and gas from subsurface zones at the maximum efficiency rate for the United States Government. NPR-3 generates more than 60 discrete waste streams, many of significant volume. Most of these waste streams are categorized as wastes from the exploration, development and production of oil and gas and, as such, are exempt from Subtitle C of RCRA as indicated in the regulatory determination published in the Federal Register on July 6, 1988. However, because so many of these waste streams contain hazardous substances and because of an increasingly more restrictive regulatory environment, in 1990 an overall effort was made to characterize all waste streams produced and institute the best waste management practice economically practical to reduce the volume and toxicity of the waste generated

Implementing waste minimization at an active plutonium processing facility: Successes and progress at technical area (TA) -55 of the Los Alamos National Laboratory

Energy Technology Data Exchange (ETDEWEB)

Balkey, J.J.; Robinson, M.A.; Boak, J.

1997-12-01

The Los Alamos National Laboratory has ongoing national security missions that necessitate increased plutonium processing. The bulk of this activity occurs at Technical Area -55 (TA-55), the nations only operable plutonium facility. TA-55 has developed and demonstrated a number of technologies that significantly minimize waste generation in plutonium processing (supercritical CO{sub 2}, Mg(OH){sub 2} precipitation, supercritical H{sub 2}O oxidation, WAND), disposition of excess fissile materials (hydride-dehydride, electrolytic decontamination), disposition of historical waste inventories (salt distillation), and Decontamination & Decommissioning (D&D) of closed nuclear facilities (electrolytic decontamination). Furthermore, TA-55 is in the process of developing additional waste minimization technologies (molten salt oxidation, nitric acid recycle, americium extraction) that will significantly reduce ongoing waste generation rates and allow volume reduction of existing waste streams. Cost savings from reduction in waste volumes to be managed and disposed far exceed development and deployment costs in every case. Waste minimization is also important because it reduces occupational exposure to ionizing radiation, risks of transportation accidents, and transfer of burdens from current nuclear operations to future generations.

Implementing waste minimization at an active plutonium processing facility: Successes and progress at technical area (TA) -55 of the Los Alamos National Laboratory

International Nuclear Information System (INIS)

Balkey, J.J.; Robinson, M.A.; Boak, J.

1997-01-01

The Los Alamos National Laboratory has ongoing national security missions that necessitate increased plutonium processing. The bulk of this activity occurs at Technical Area -55 (TA-55), the nations only operable plutonium facility. TA-55 has developed and demonstrated a number of technologies that significantly minimize waste generation in plutonium processing (supercritical CO 2 , Mg(OH) 2 precipitation, supercritical H 2 O oxidation, WAND), disposition of excess fissile materials (hydride-dehydride, electrolytic decontamination), disposition of historical waste inventories (salt distillation), and Decontamination ampersand Decommissioning (D ampersand D) of closed nuclear facilities (electrolytic decontamination). Furthermore, TA-55 is in the process of developing additional waste minimization technologies (molten salt oxidation, nitric acid recycle, americium extraction) that will significantly reduce ongoing waste generation rates and allow volume reduction of existing waste streams. Cost savings from reduction in waste volumes to be managed and disposed far exceed development and deployment costs in every case. Waste minimization is also important because it reduces occupational exposure to ionizing radiation, risks of transportation accidents, and transfer of burdens from current nuclear operations to future generations

Chelating water-soluble polymers for waste minimization

International Nuclear Information System (INIS)

Smith, B.; Cournoyer, M.; Duran, B.; Ford, D.; Gibson, R.; Lin, M.; Meck, A.; Robinson, P.; Robison, T.

1996-01-01

Within the DOE complex and in industry there is a tremendous need for advanced metal ion recovery and waste minimization techniques. This project sought to employ capabilities for ligand-design and separations chemistry in which one can develop and evaluate water- soluble chelating polymers for recovering actinides and toxic metals from various process streams. Focus of this work was (1) to develop and select a set of water-soluble polymers suitable for a selected waste stream and (2) demonstrate this technology in 2 areas: removal of (a) actinides and toxic RCRA metals from waste water and (b) recovery of Cu and other precious metals from industrial process streams including from solid catalysts and aqueous waste streams. The R ampersand D was done in 4 phases for each of the 2 target areas: polymer synthesis for scaleup, equipment assembly, process demonstration at a DOE or industrial site, and advanced ligand/polymer synthesis. The TA- 50 site at Los Alamos was thought to be appropriate due to logistics and to its being representative of similar problems throughout the DOE complex

Mixed-waste minimization activities in the nuclear weapons complex

International Nuclear Information System (INIS)

Marchetti, J.A.; Suffern, J.S.

1991-01-01

Over the past 40 years, the US Department of Energy (DOE) and the nuclear weapons complex have successfully executed their mission of providing the country with a strong nuclear deterrent. Now, however, they must attain another mission at the same time: to eliminate or greatly reduce the environmental, safety, and health problems in the complex. Mixed-waste minimization activities have taken place in 11 of the complex production plants and laboratories: the Pinellas plant, the Mount plant, the Kansas City plant, the Y-12 plant, the Rocky Flats plant, the Savannah River Site (SRS), the Savannah River Site (SRS), the Pantex plant, the Nevada Test Site, Sandia National Laboratories, Los Alamos National Laboratory, and the Lawrence Livermore National Laboratory. The mixed-waste minimization opportunities that have been implemented to date by the production facilities are different from those that have been implemented by the laboratories. Areas of opportunity at the plants involve the following activities: (1) process design or improvement; (2) substitution of materials; (3) waste segregation; (4) recycling; and (5) administrative controls

Treatment and minimization of heavy metal-containing wastes 1995

International Nuclear Information System (INIS)

Hager, J.P.; Mishra, B.; Litz, J.L.

1995-01-01

This symposium was held in conjunction with the 1995 Annual Meeting of the Minerals, Metals and Materials Society in Las Vegas, Nevada, February 12--16, 1995. The purpose of this meeting was to provide a forum for exchange of state-of-the-art information on treating and minimizing heavy metal-containing wastes. Papers were categorized under the following broad headings: aqueous processing; waste water treatment; thermal processing and stabilization; processing of fly ash, flue dusts, and slags; and processing of lead, mercury, and battery wastes. Individual papers have been processed separately for inclusion in the appropriate data bases

A new waste minimization method for the determination of total nonhalogenated volatile organic compounds in TRU wastes

International Nuclear Information System (INIS)

Sandoval, W.; Quintana, B.D.; Ortega, L.

1997-01-01

As part of the technical support CST-12 provides for a wide variety of defense and nondefense programs within Los Alamos National Laboratory (LANL) and the Department of Energy (DOE) complex, new waste minimization technique is under development for radiological volatile organic analysis (Hot VOA). Currently all HOT VOA must be run in a glovebox. Several types of sample contain TRU radiological waste in the form of particulates. By prefiltering the samples through a 1.2 micron syringe and counting the radioactivity, it has been found that many of the samples can be analyzed outside a glovebox. In the present investigation, the types of Hot VOA samples that can take advantage of this new technique, the volume and types of waste reduced and the experimental parameters will be discussed. Overall, the radioactive waste generated is minimized

RCRA Permit for a Hazardous Waste Management Facility Permit Number NEV HW0101 Annual Summary/Waste Minimization Report Calendar Year 2011

Energy Technology Data Exchange (ETDEWEB)

NSTec Environmental Restoration

2012-02-16

This report summarizes the U.S. Environmental Protection Agency (EPA) identification number of each generator from which the Permittee received a waste stream; a description and quantity of each waste stream in tons and cubic feet received at the facility; the method of treatment, storage, and/or disposal for each waste stream; a description of the waste minimization efforts undertaken; a description of the changes in volume and toxicity of waste actually received; any unusual occurrences; and the results of tank integrity assessments. This Annual Summary/Waste Minimization Report is prepared in accordance with Section 2.13.3 of Permit Number NEV HW0101.

Waste minimization activities in the Materials Fabrication Division at Lawrence Livermore National Laboratory

International Nuclear Information System (INIS)

Dini, J.W.

1991-08-01

The mission of the Materials Fabrication Division (MFD) is to provide fabrication services and technology in support of all programs at Lawrence Livermore National Laboratory (LLNL). MFD involvement is called for when fabrication activity requires levels of expertise, technology, equipment, process development, hazardous processes, security, or scheduling that is typically not commercially available. Customers are encouraged to utilize private industry for fabrication activity requiring routine processing or for production applications. Our waste minimization (WM) program has been directed at source reduction and recycling in concert with the working definition of waste minimization used by EPA. The principal focus of WM activities has been on hazardous wastes as defined by RCRA, however, all pollutant emissions into air, water and land are being considered as part of the program. The incentives include: (1) economics, (2) regulatory conformance, (3) public image and (4) environmental concern. This report discusses the waste minimization program at LLNL

Pollution prevention and waste minimization opportunity assessment in environmental restoration

International Nuclear Information System (INIS)

Roybal, J.A.; Willison, C.P.

1997-01-01

The Environmental Restoration (ER) Project at Sandia National Laboratories implicitly subscribed to the philosophy of pollution prevention and waste minimization. As a result of a Department of Energy (DOE) offer, Pollution Prevention Opportunity Assessments (PPOA) were conducted at two ER sites and a decontamination and Demolition (D and D) site. The purpose of one of the PPOAs was to identify pollution prevention (P2) opportunities during environmental remediation at the Classified Waste Landfill located at Sandia National Laboratories, New Mexico (SNL/NM). The remediation activities at this site are scheduled to begin in the fall of 1997. The PPOA included presentations by the team members, a tour of the site, and a brainstorming session to list the waste streams, identify P2 opportunities and rank them in order of priority. Twenty-five P2 opportunities were identified during the brainstorming session of which twenty-two opportunities were selected for further investigation. Those twenty-two opportunities are discussed in this paper. A cost benefit analysis was performed for each P2 opportunity based on the estimated waste volume, feasibility, and cost. Pollution Prevention by Design (P2D) was incorporated into the PPOA to introduce waste minimization techniques that can be used during the planning phase of restoration projects

40 CFR 63.1213 - How can the compliance date be extended to install pollution prevention or waste minimization...

Science.gov (United States)

2010-07-01

... to install pollution prevention or waste minimization controls? 63.1213 Section 63.1213 Protection of... pollution prevention or waste minimization controls? (a) Applicability. You may request from the... must contain the following information: (i) A description of pollution prevention or waste minimization...

IDENTIFICATION AND CLASSIFICATION OF INDUSTRIAL SOLID WASTES IN AMMONIA UNIT OF RAZI PETROCHEMICAL COMPLEX AND FEASIBILITY OF WASTE MINIMIZATION

Directory of Open Access Journals (Sweden)

F. Fakheri Raouf, R. Nabizadeh and N. Jafarzadeh

2005-10-01

Full Text Available Petrochemical industries are considered as strategic and important sectors in economic development of Iran. Razi petrochemical factory is one of complex in Iran, established in 1970 with 100 hectare. In this research, the possibility of waste minimization in the ammonia unit of Razi petrochemical complex with about 1000 tons per year was studied for a period of 18 months from September 2003 to April 2005. More than 20 site visits were conducted and the required information was collected. Factors such as industrial solid wastes quality and quantity, sources of generation, production period and the present management practice, were studied. Petrochemical solid wastes were classified based on the recommended method of the United Nations and appropriate policies were suggested for waste minimization. The collected results of this study show production of 185 tons of industrial solid wastes from 45 sources which contained 68.5% catalysts, 10.25% metal barrels, 18.61% aluminum ball, 2.62% plastic barrels and 0.02% paper. 93.3% of these wastes were generated as the result of catalysts change, 3.3% as the result of using chemicals and oils, 1.7% as the result of methanol solution amid application, and 1.1% because of aluminum ball changes. Based on the UNEP methods, the ammonia unit wastes classified as 19/7%hazadrous and 87,12% non hazardous. At present 87.12% of these wastes are being dumped in the area and 12.88% are sold. Proposed procedures for waste minimization contain 68.5% reuse and recycling and 31.5% recycling.

Waste minimization and pollution prevention awareness plan

International Nuclear Information System (INIS)

1994-08-01

The primary mission of DOE/NV is to manage and operate the Nevada Test Site (NTS) and other designated test locations, within and outside the United States; provide facilities and services to DOE and non-DOE NTS users; and plan. coordinate, and execute nuclear weapons tests and related test activities. DOE/NV also: (a) Supports operations under interagency agreements pertaining to tests, emergencies, and related functions/activities, (b) Plans, coordinates, and executes environmental restoration, (c) Provides support to the Yucca Mountain Site Characterization Project Office in conjunction with DOE/HQ oversight, (d) Manages the Radioactive Waste Management Sites (RWMS) for disposal of low-level and mixed wastes received from the NTS and off-site generators, and (e) Implements waste minimization programs to reduce the amount of hazardous, mixed, radioactive, and nonhazardous solid waste that is generated and disposed The NTS, which is the primary facility controlled by DOE/NV, occupies 1,350 square miles of restricted-access, federally-owned land located in Nye County in Southern Nevada. The NTS is located in a sparsely populated area, approximately 65 miles northwest of Las Vegas, Nevada

Trends for minimization of radioactive waste arising from spent nuclear fuel reprocessing

International Nuclear Information System (INIS)

Polyakov, A.S.; Koltunov, V.S.; Marchenko, V.I.; Ilozhev, A.P.; Mukhin, I.V.

2000-01-01

Research and development of technologies for radioactive waste (RAW) minimization arising from spent nuclear fuel reprocessing are discussed. Novel reductants of Pu and Np ions, reagents of purification recycled extractant, possibility of the electrochemical methods are studied. The partitioning of high activity level waste are considered. Examples of microbiological methods decomposition of radioactive waste presented. (authors)

ENVIRONMENTAL RESEARCH BRIEF: WASTE MINIMIZATION ASSESSMENT FOR A MANUFACTURER OF REBUILT RAILWAY CARS AND COMPONENTS

Science.gov (United States)

The U.S. Environmental Protection Agency (EPA) has funded a pilot project to assist small- and medium- size manufacturers who want to minimize their generation of hazardous waste but lack the expertise to do so. Waste Minimization Assessment Centers (WMACs) were established at se...

Best Practice of Construction Waste Management and Minimization

Directory of Open Access Journals (Sweden)

Khor Jie Cheng

2014-07-01

Full Text Available Material management is an important issue as seen in construction waste management. Best practice of material management is accompanied by various benefits which are acknowledged by several studies. The site layout has particular effects on both materials and their waste through effective waste management practice. Ignoring the benefits of material management could result in a daily reduction in productivity of up to 40% by material wastage. Thus, the benefits of effective material management must be well comprehended for the sake of waste minimization. Another convincing fact about waste is that poor site management accounts for the largest factor of waste generation. Hence the site condition is very crucial in developing effective material management. Factors contributing to the efficiency of material management process are effective logistical management and supply chain management. The logistics system must be performing as schedule so that materials are wisely managed on-site without encountering presence of excessive materials. As materials management is closely related to logistics in construction projects, there will be delay in construction projects when materials are not delivered to site as scheduled. The management must be effective in terms of delivery, off-loading, storage, handling, on-site transportation and on-site utilization of materials.

Pollution prevention/waste minimization program 1998 fiscal year work plan - WBS 1.11.2.1

International Nuclear Information System (INIS)

Howald, S.C.; Merry, D.S.

1997-09-01

Pollution Prevention/Waste Minimization (P2/WMin) is the Department of Energy's preferred approach to environmental management. The P2/WMin mission is to eliminate or minimize waste generation, pollutant releases to the environment, use of toxic substances, and to conserve resources by implementing cost-effective pollution prevention technologies, practices, and polices

Waste Minimization and Pollution Prevention Awareness Plan

International Nuclear Information System (INIS)

1994-04-01

The purpose of this plan is to document Lawrence Livermore National Laboratory (LLNL) projections for present and future waste minimization and pollution prevention. The plan specifies those activities and methods that are or will be used to reduce the quantity and toxicity of wastes generated at the site. It is intended to satisfy Department of Energy (DOE) requirements. This Plan provides an overview of projected activities from FY 1994 through FY 1999. The plans are broken into site-wide and problem-specific activities. All directorates at LLNL have had an opportunity to contribute input, to estimate budget, and to review the plan. In addition to the above, this plan records LLNL's goals for pollution prevention, regulatory drivers for those activities, assumptions on which the cost estimates are based, analyses of the strengths of the projects, and the barriers to increasing pollution prevention activities

The U.S. DOE new production reactor/heavy water reactor facility pollution prevention/waste minimization program

International Nuclear Information System (INIS)

Kaczmarsky, Myron M.; Tsang, Irving; Stepien, Walter P.

1992-01-01

A Pollution Prevention/Waste Minimization Program was established during the early design phase of the U.S. DOE's New Production Reactor/Heavy Water Reactor Facility (NPR/HWRF) to encompass design, construction, operation and decommissioning. The primary emphasis of the program was given to waste elimination, source reduction and/or recycling to minimize the quantity and toxicity of material before it enters the waste stream for treatment or disposal. The paper discusses the regulatory and programmatic background as it applies to the NPR/HWRF and the waste assessment program developed as a phased approach to pollution prevention/waste minimization for the NPR/HWRF. Implementation of the program will be based on various factors including life cycle cost analysis, which will include costs associated with personnel, record keeping, transportation, pollution control equipment, treatment, storage, disposal, liability, compliance and oversight. (author)

Potential pollution prevention and waste minimization for Department of Energy operations

International Nuclear Information System (INIS)

Griffin, J.; Ischay, C.; Kennicott, M.; Pemberton, S.; Tull, D.

1995-10-01

With the tightening of budgets and limited resources, it is important to ensure operations are carried out in a cost-effective and productive manner. Implementing an effective Pollution Prevention strategy can help to reduce the costs of waste management and prevent harmful releases to the environment. This document provides an estimate of the Department of Energy's waste reduction potential from the implementation of Pollution Prevention opportunities. A team of Waste Minimization and Pollution Prevention professionals was formed to collect the data and make the estimates. The report includes a list of specific reduction opportunities for various waste generating operations and waste types. A generic set of recommendations to achieve these reduction opportunities is also provided as well as a general discussion of the approach and assumptions made for each waste generating operation

Environmental Restoration Contractor Waste Minimization and Pollution Prevention Plan. Revision 1

International Nuclear Information System (INIS)

Lewis, R.A.

1996-03-01

This plan contains the Environmental Restoration Contractor (ERC) Waste Minimization and Pollution Prevention (WMin/P2) Program. The plan outlines the activities and schedules developed by the ERC to reduce the quantity and toxicity of waste dispositioned as a result of restoration and remediation activities. This plan satisfies US Department of Energy (DOE) requirements including the Pollution Prevention Awareness program required by DOE Order 5400.1 (DOE 1988). This plan is consistent with Executive Order 12856 and Secretary O'Leary's pollution prevention Policy Statement of December 27, 1994, which set US and DOE pollution prevention policies, respectively. It is also consistent with the DOE Pollution Prevention Crosscut Plan, 1994, which provides guidance in meeting the DOE goals in pollution prevention. The purpose of this plan is to aid ERC projects in meeting and documenting compliance with requirements for WMin/P2. This plan contains the objectives, strategy, and support activities of the ERC Team WMin/P2 program. The basic elements of the plan are pollution prevention goals, waste assessments of major waste streams, implementation of feasible waste minimization opportunities, and a process for reporting achievements. Wherever appropriate, the ERC will integrate the pollution prevention activities in this plan into regular program activities rather than establishing separate WMin/P2 activities. Moreover, wherever possible, existing documents, procedures, and activities will be used to meet WMin/P2 requirements

Community participation in waste minimization : the case of Emfuleni Local Municipality / Nompazamo Alma Ludidi

OpenAIRE

Ludidi, Nompazamo Alma

2009-01-01

The purpose of this research is to understand factors contributing to successes and challenges in community participation especially in waste minimization initiatives; in order to inform policies and contribute to improve the design of the initiative. The objectives of the research are: firstly, to understand the current state of public participation in waste minimization at Emfuleni Local Municipality. Secondly, it is to determine the extent of willingness of the community to participate in ...

Unrestricted disposal of minimal activity levels of radioactive wastes: exposure and risk calculations

International Nuclear Information System (INIS)

Fields, D.E.; Emerson, C.J.

1984-08-01

The US Nuclear Regulatory Commission is currently considering revision of rule 10 CFR Part 20, which covers disposal of solid wastes containing minimal radioactivity. In support of these revised rules, we have evaluated the consequences of disposing of four waste streams at four types of disposal areas located in three different geographic regions. Consequences are expressed in terms of human exposures and associated health effects. Each geographic region has its own climate and geology. Example waste streams, waste disposal methods, and geographic regions chosen for this study are clearly specified. Monetary consequences of minimal activity waste disposal are briefly discussed. The PRESTO methodology was used to evaluate radionuclide transport and health effects. This methodology was developed to assess radiological impacts to a static local population for a 1000-year period following disposal. Pathways and processes of transit from the trench to exposed populations included the following considerations: groundwater transport, overland flow, erosion, surface water dilution, resuspension, atmospheric transport, deposition, inhalation, and ingestion of contaminated beef, milk, crops, and water. 12 references, 2 figures, 8 tables

Gas cylinder disposal pit remediation waste minimization and management

International Nuclear Information System (INIS)

Alas, C.A.; Solow, A.; Criswell, C.W.; Spengler, D.; Brannon, R.; Schwender, J.M.; Eckman, C.K.; Rusthoven, T.

1995-01-01

A remediation of a gas cylinder disposal pit at Sandia National Laboratories, New Mexico has recently been completed. The cleanup prevented possible spontaneous releases of hazardous gases from corroded cylinders that may have affected nearby active test areas at Sandia's Technical Area III. Special waste management, safety, and quality plans were developed and strictly implemented for this project. The project was conceived from a waste management perspective, and waste minimization and management were built into the planning and implementation phases. The site layout was planned to accommodate light and heavy equipment, storage of large quantities of suspect soil, and special areas to stage and treat gases and reactive chemicals removed from the pit, as well as radiation protection areas. Excavation was a tightly controlled activity using experienced gas cylinder and reactive chemical specialists. Hazardous operations were conducted at night under lights, to allow nearby daytime operations to function unhindered. The quality assurance plan provided specific control of, and documentation for, critical decisions, as well as the record of daily operations. Both hand and heavy equipment excavation techniques were utilized. Hand excavation techniques were utilized. Hand excavation techniques allows sealed glass containers to be exhumed unharmed. In the end, several dozen thermal batteries; 5 pounds (2.3 kg) of lithium metal; 6.6 pounds (3.0 kg) of rubidium metal; several kilograms of unknown chemicals; 140 cubic yards (107 cubic meters) of thorium-contaminated soil; 270 cubic yards (205 cubic meters) of chromium-contaminated soil; and 450 gas cylinders, including 97 intact cylinders containing inert, flammable, toxic, corrosive, or oxidizing gases were removed and effectively managed to minimize waste

Information processing to determine waste minimization/pollution prevention strategies in the petroleum industry

Energy Technology Data Exchange (ETDEWEB)

Falcon, Mariali F. de [CORPOVEN, S.A. (Venezuela)

1994-12-31

With the passage of the 1984 Hazardous and Solid Waste Amendments to the Resource Conservation and Recovery Act in the United States, industries, and particularly the petroleum industry, have become more interested in their waste management practices. This works aims to present a methodology to organize the collected data concerning waste minimization and, or, pollution prevention in the petroleum industry into a bibliographic database

Information processing to determine waste minimization/pollution prevention strategies in the petroleum industry

Energy Technology Data Exchange (ETDEWEB)

Falcon, Mariali F. de [CORPOVEN, S.A. (Venezuela)

1993-12-31

With the passage of the 1984 Hazardous and Solid Waste Amendments to the Resource Conservation and Recovery Act in the United States, industries, and particularly the petroleum industry, have become more interested in their waste management practices. This works aims to present a methodology to organize the collected data concerning waste minimization and, or, pollution prevention in the petroleum industry into a bibliographic database

Lessons Learned at Envirocare of Utah's Containerized Waste Facility (CWF): Dose Minimization Through ALARA Techniques and Tools

International Nuclear Information System (INIS)

Heckman, J.; Gardner, J.; Ledoux, M. R.

2003-01-01

Envirocare of Utah, Inc. (Envirocare) commenced operation of its Class A Containerized Waste Facility (CWF) on October 25, 2001. The opening of this facility began a new era for Envirocare, in that; their core business had always been low level, high volume, bulk radioactive waste. The CWF commenced operations to dispose of low level, low volume, high activity, containerized radioactive waste. Due to the potential for high dose rates on the waste disposal containers, the ALARA principle (As Low As Reasonably Achievable) plays an important role in the operation of the CWF and its mission to properly dispose of waste while minimizing doses to the workers, public, and the environment. This paper will enumerate some of the efforts made by the management and staff of the CWF that have contributed to significant dose reductions

Hanford Site waste minimization and pollution prevention awareness program plan

International Nuclear Information System (INIS)

Place, B.G.

1998-01-01

This plan, which is required by US Department of Energy (DOE) Order 5400. 1, provides waste minimization and pollution prevention guidance for all Hanford Site contractors. The plan is primary in a hierarchical series that includes the Hanford Site Waste Minimization and Pollution Prevention Awareness Program Plan, Prime contractor implementation plans, and the Hanford Site Guide for Preparing and Maintaining Generator Group Pollution Prevention Program Documentation (DOE-RL, 1997a) describing programs required by Resource Conservation and Recovery Act of 1976 (RCRA) 3002(b) and 3005(h) (RCRA and EPA, 1994). Items discussed include the pollution prevention policy and regulatory background, organizational structure, the major objectives and goals of Hanford Site's pollution prevention program, and an itemized description of the Hanford Site pollution prevention program. The document also includes US Department of Energy, Richland Operations Office's (RL's) statement of policy on pollution prevention as well as a listing of regulatory drivers that require a pollution prevention program

Waste minimization, recycling and reuse in operations support services fleet maintenance

International Nuclear Information System (INIS)

Trego, A.L.

1994-01-01

Government regulations and smart business practices demand that organizations dramatically reduce both the type and volume of waste generated by their operations. This article describes successful waste minimization and recycling programs created by the Fleet Maintenance, Operations Support Services Division, Westinghouse Hanford Company. These comprehensive programs have greatly reduced waste formerly produced in maintaining 3,528 government-owned vehicles and nearly 200 emergency power generators at the Hanford Site. The actions are integral to preventing future contamination of the Site as well as to cleaning up the complexity of wastes from almost 50 years of defense production. The results of the Fleet Maintenance programs are impressive, recording cost savings of $290,000 in fiscal year 1993 and $965,000 since 1988

Swords into plowshares -- Tritium waste minimization (training development project)

International Nuclear Information System (INIS)

Hehmeyer, J.; Sienkiewicz, C.; Kent, L.; Gill, J.; Schmitz, W.; Mills, T.; Wurstner, R.; Adams, F.; Seabaugh, P.

1995-01-01

A concentrated emphasis of Mound's historical mission has been working with tritium. As the phase out of defense work begins and the increase on environmental technology strengthens, so too must a shift occur in applying one's focus. Mound's longstanding efforts in Tritium Training have proven fruitful to them and the Complex. It is this emphasis for which a new generation of worker training is being developed, one which reflects a new mission; Tritium Waste Minimization. The efforts of previous training, particularly under Accreditation, have given a solid base on which to launch the Waste Minimization program. Typical operations consider the impact on the varying levels of containment and the tools and agents used to achieve those levels. D and D and system modifications are bringing new light to such things as floor tile, oils, mole sieves, and rust. Of financial interest is the amount of savings which have been obtained through review and modification, rather than developing a new program. The authors are learning not to reinvent the wheel. The presentation will compare and contrast the methodologies used in creating and implementing this training program. Emphasis will be placed on lessons learned, costs saved, and program enhancement

Minimization of municipal solid waste transportation route in West Jakarta using Tabu Search method

Science.gov (United States)

Chaerul, M.; Mulananda, A. M.

2018-04-01

Indonesia still adopts the concept of collect-haul-dispose for municipal solid waste handling and it leads to the queue of the waste trucks at final disposal site (TPA). The study aims to minimize the total distance of waste transportation system by applying a Transshipment model. In this case, analogous of transshipment point is a compaction facility (SPA). Small capacity of trucks collects the waste from waste temporary collection points (TPS) to the compaction facility which located near the waste generator. After compacted, the waste is transported using big capacity of trucks to the final disposal site which is located far away from city. Problem related with the waste transportation can be solved using Vehicle Routing Problem (VRP). In this study, the shortest distance of route from truck pool to TPS, TPS to SPA, and SPA to TPA was determined by using meta-heuristic methods, namely Tabu Search 2 Phases. TPS studied is the container type with total 43 units throughout the West Jakarta City with 38 units of Armroll truck with capacity of 10 m3 each. The result determines the assignment of each truck from the pool to the selected TPS, SPA and TPA with the total minimum distance of 2,675.3 KM. The minimum distance causing the total cost for waste transportation to be spent by the government also becomes minimal.

Foam is a decon waste minimization tool

International Nuclear Information System (INIS)

Peterson, K.D.; McGlynn, J.F.; Rankin, W.N.

1991-01-01

The use of foam in decontamination operations offers significant reductions in waste generation. Initial use has confirmed its effectiveness. Issues being resolved at Savannah River Site (SRS) include compatibility of foam generating solutions with decontamination solutions, waste disposal, and operational safety

1994 Annual report on waste generation and waste minimization progress as required by DOE Order 5400.1, Hanford Site

International Nuclear Information System (INIS)

1995-09-01

Many Waste Minimization/Pollution Prevention successes at the Hanford Site occur every day without formal recognition. A few of the successful projects are: T-Plant helps facilities reuse equipment by offering decontamination services for items such as gas cylinders, trucks, and railcars, thus saving disposal and equipment replacement costs. Custodial Services reviewed its use of 168 hazardous cleaning products, and, through a variety of measures, replaced them with 38 safer substitutes, one for each task. Scrap steel contaminated with low level radioactivity from the interim stabilization of 107-K and 107-C was decontaminated and sold to a vendor for recycling. Site-wide programs include the following: the Pollution Prevention Opportunity Assessment (P2OA) program at the Hanford site was launched during 1994, including a training class, a guidance document, technical assistance, and goals; control over hazardous materials purchased was achieved by reviewing all purchase requisitions of a chemical nature; the Office Supply Reuse Program was established to redeploy unused or unwanted office supply items. In 1994, pollution prevention activities reduced approximately 274,000 kilograms of hazardous waste, 2,100 cubic meters of radioactive and mixed waste, 14,500,000 kilograms of sanitary waste, and 215,000 cubic meters off liquid waste and waste water. Pollution Prevention activities also saved almost $4.2 million in disposal, product, and labor costs. Overall waste generation increased in 1994 due to increased work and activity typical for a site with an environmental restoration mission. However, without any Waste Minimization/Pollution Prevention activities, solid radioactive waste generation at Hanford would have been 25% higher, solid hazardous waste generation would have been 30% higher, and solid sanitary waste generation would have been 60% higher

RCRA Permit for a Hazardous Waste Management Facility Permit Number NEV HW0101 Annual Summary/Waste Minimization Report Calendar Year 2012, Nevada National Security Site, Nevada

Energy Technology Data Exchange (ETDEWEB)

Arnold, P. M.

2013-02-21

This report summarizes the U.S. Environmental Protection Agency (EPA) identification number of each generator from which the Permittee received a waste stream, a description and quantity of each waste stream in tons and cubic feet received at the facility, the method of treatment, storage, and/or disposal for each waste stream, a description of the waste minimization efforts undertaken, a description of the changes in volume and toxicity of waste actually received, any unusual occurrences, and the results of tank integrity assessments. This Annual Summary/Waste Minimization Report is prepared in accordance with Section 2.13.3 of Permit Number NEV HW0101, issued 10/17/10.

Minimizing Characterization - Derived Waste at the Department of Energy Savannah River Site, Aiken, South Carolina

Energy Technology Data Exchange (ETDEWEB)

Van Pelt, R. S.; Amidon, M. B.; Reboul, S. H.

2002-02-25

Environmental restoration activities at the Department of Energy Savannah River Site (SRS) utilize innovative site characterization approaches and technologies that minimize waste generation. Characterization is typically conducted in phases, first by collecting large quantities of inexpensive data, followed by targeted minimally invasive drilling to collect depth-discrete soil/groundwater data, and concluded with the installation of permanent multi-level groundwater monitoring wells. Waste-reducing characterization methods utilize non-traditional drilling practices (sonic drilling), minimally intrusive (geoprobe, cone penetrometer) and non-intrusive (3-D seismic, ground penetration radar, aerial monitoring) investigative tools. Various types of sensor probes (moisture sensors, gamma spectroscopy, Raman spectroscopy, laser induced and X-ray fluorescence) and hydrophobic membranes (FLUTe) are used in conjunction with depth-discrete sampling techniques to obtain high-resolution 3-D plume profiles. Groundwater monitoring (short/long-term) approaches utilize multi-level sampling technologies (Strata-Sampler, Cone-Sipper, Solinst Waterloo, Westbay) and low-cost diffusion samplers for seepline/surface water sampling. Upon collection of soil and groundwater data, information is portrayed in a Geographic Information Systems (GIS) format for interpretation and planning purposes. At the SRS, the use of non-traditional drilling methods and minimally/non intrusive investigation approaches along with in-situ sampling methods has minimized waste generation and improved the effectiveness and efficiency of characterization activities.

Minimizing Characterization - Derived Waste at the Department of Energy Savannah River Site, Aiken, South Carolina

International Nuclear Information System (INIS)

Van Pelt, R. S.; Amidon, M. B.; Reboul, S. H.

2002-01-01

Environmental restoration activities at the Department of Energy Savannah River Site (SRS) utilize innovative site characterization approaches and technologies that minimize waste generation. Characterization is typically conducted in phases, first by collecting large quantities of inexpensive data, followed by targeted minimally invasive drilling to collect depth-discrete soil/groundwater data, and concluded with the installation of permanent multi-level groundwater monitoring wells. Waste-reducing characterization methods utilize non-traditional drilling practices (sonic drilling), minimally intrusive (geoprobe, cone penetrometer) and non-intrusive (3-D seismic, ground penetration radar, aerial monitoring) investigative tools. Various types of sensor probes (moisture sensors, gamma spectroscopy, Raman spectroscopy, laser induced and X-ray fluorescence) and hydrophobic membranes (FLUTe) are used in conjunction with depth-discrete sampling techniques to obtain high-resolution 3-D plume profiles. Groundwater monitoring (short/long-term) approaches utilize multi-level sampling technologies (Strata-Sampler, Cone-Sipper, Solinst Waterloo, Westbay) and low-cost diffusion samplers for seepline/surface water sampling. Upon collection of soil and groundwater data, information is portrayed in a Geographic Information Systems (GIS) format for interpretation and planning purposes. At the SRS, the use of non-traditional drilling methods and minimally/non intrusive investigation approaches along with in-situ sampling methods has minimized waste generation and improved the effectiveness and efficiency of characterization activities

Waste minimization via destruction of hazardous organics

International Nuclear Information System (INIS)

Austin, L.R.

1991-01-01

Los Alamos National Laboratory is developing technologies that are capable of destroying hazardous organics, that is, converting them basically to water and carbon dioxide. If these technologies were incorporated into the main processing operation where the waste is produced, then the volume and toxicity of the hazardous or mix hazardous waste generated would be significantly reduced. This presentation will briefly discuss some of the waste treatment technologies under development at Los Alamos National Laboratory focused on destroying hazardous organics

From waste minimization to ISO 14000: Taiwan`s experience and prospects

Energy Technology Data Exchange (ETDEWEB)

Wen-Huei Chen; Wain-Sun Hou [China Technical Consultants, Inc., Taipei (Taiwan, Province of China)

1996-12-31

Taiwan has completed a very successful five-year industrial waste minimization (IWM) demonstration and promotion project sponsored by the government. From 1990 to 1995, the project successfully disseminated the IWM concept of pollution prevention (P2) to industries. It effectively reduced industrial waste while significantly benefitting the economy by assisting industries in implementing in-plant IWM programs. In July 1995, the second stage of the five-year IWM and ISO 14000 promotion project was initiated for further promoting the IWM, P2, and cleaner production and, in particular, coping with the upcoming international environmental management standards (ISO 14000). To assist industries in establishing an environmental management system (EMS) and accumulating related experience, an EMS pilot demonstration project of five model industries and an ISO 14001 EMS demonstration and promotion project for 22 factories in 13 industries were initiated in October 1995 and August 1996, respectively. These projects can assist Taiwan`s industries in changing the constitution of their enterprises, enhancing competition in the international market, and helping our nation achieve the forerunner`s profits in sustainable development. 9 refs., 3 figs.

WESF hot cells waste minimization criteria hot cells window seals evaluation

International Nuclear Information System (INIS)

Walterskirchen, K.M.

1997-01-01

WESF will decouple from B Plant in the near future. WESF is attempting to minimize the contaminated solid waste in their hot cells and utilize B Plant to receive the waste before decoupling. WESF wishes to determine the minimum amount of contaminated waste that must be removed in order to allow minimum maintenance of the hot cells when they are placed in ''laid-up'' configuration. The remaining waste should not cause unacceptable window seal deterioration for the remaining life of the hot cells. This report investigates and analyzes the seal conditions and hot cell history and concludes that WESF should remove existing point sources, replace cerium window seals in F-Cell and refurbish all leaded windows (except for A-Cell). Work should be accomplished as soon as possible and at least within the next three years

Implementation of Lean Warehouse to Minimize Wastes in Finished Goods Warehouse of PT Charoen Pokphand Indonesia Semarang

Directory of Open Access Journals (Sweden)

Nia Budi Puspitasari

2016-03-01

Full Text Available PT. Charoen Pokphand Indonesia Semarang is one of the largest poultry feed companies in Indonesia. To store the finished products that are ready to be distributed, it needs a finished goods warehouse. To minimize the wastes that occur in the process of warehousing the finished goods, the implementation of lean warehouse is required. The core process of finished goods warehouse is the process of putting bag that has been through the process of pallets packing, and then transporting the pallets contained bags of feed at finished goods warehouses and the process of unloading food from the finished goods warehouse to the distribution truck. With the implementation of the lean warehouse, we can know whether the activities are value added or not, to be identified later which type of waste happened. Opinions of stakeholders regarding the waste that must be eliminated first need to be determined by questionnaires. Based on the results of the questionnaires, three top wastes are selected to be identified the cause by using fishbone diagram. They can be repaired by using the implementation of 5S, namely Seiri, Seiton, Seiso, Seiketsu, and Shitsuke. Defect waste can be minimized by selecting pallet, putting sack correctly, forklift line clearance, applying working procedures, and creating cleaning schedule. Next, overprocessing waste is minimized by removing unnecessary items, putting based on the date of manufacture, and manufacture of feed plan. Inventory waste is minimized by removing junks, putting feed based on the expired date, and cleaning the barn

Annual Waste Minimization Summary Report for the National Nuclear Security Administration Nevada Site Office

International Nuclear Information System (INIS)

Alfred J. Karns

2007-01-01

This report summarizes the waste minimization efforts undertaken by National Security Technologies, LLC (NSTec), for the U. S. Department of Energy (DOE) National Nuclear Security Administration Nevada Site Office (NNSA/NSO), during CY06. This report was developed in accordance with the requirements of the Nevada Test Site (NTS) Resource Conservation and Recovery Act (RCRA) Permit ((number s ign)NEV HW0021) and as clarified in a letter dated April 21, 1995, from Paul Liebendorfer of the Nevada Division of Environmental Protection to Donald Elle of the DOE, Nevada Operations Office. The NNSA/NSO Pollution Prevention (P2) Program establishes a process to reduce the volume and toxicity of waste generated by the NNSA/NSO and ensures that proposed methods of treatment, storage, and/or disposal of waste minimize potential threats to human health and the environment. The following information provides an overview of the P2 Program, major P2 accomplishments during the reporting year, a comparison of the current year waste generation to prior years, and a description of efforts undertaken during the year to reduce the volume and toxicity of waste generated by the NNSA/NSO

Chemical and mechanical decontamination processes to minimize secondary waste decommissioning

International Nuclear Information System (INIS)

Enda, M.; Ichikawa, N.; Yaita, Y.; Kanasaki, T.; Sakai, H.

2008-01-01

In the decommissioning of commercial nuclear reactors in Japan, prior to the dismantling of the nuclear power plants, there are plans to use chemical techniques to decontaminate reactor pressure vessels (RPVs), internal parts, primary loop recirculation systems (PLRs), reactor water clean up systems (RWCUs), etc., so as to minimize radiation sources in the materials to be disposed of. After dismantling the nuclear power plants, chemical and mechanical decontamination techniques will then be used to reduce the amounts of radioactive metallic waste. Toshiba Corporation has developed pre-dismantling and post-dismantling decontamination systems. In order to minimize the amounts of secondary waste, the T-OZON process was chosen for decontamination prior to the dismantling of nuclear power plants. Dismantling a nuclear power plant results in large amounts of metallic waste requiring decontamination; for example, about 20,000 tons of such waste is expected to result from the dismantling of a 110 MWe Boiling Water Reactor (BWR). Various decontamination methods have been used on metallic wastes in preparation for disposal in consideration of the complexity of the shapes of the parts and the type of material. The materials in such nuclear power plants are primarily stainless steel and carbon steel. For stainless steel parts having simple shapes, such as plates and pipes, major sources of radioactivity can be removed from the surface of the parts by bipolar electrolysis (electrolyte: H 2 SO 4 ). For stainless steel parts having complicated shapes, such as valves and pumps, major sources of radioactivity can be removed from the surfaces by redox chemical decontamination treatments (chemical agent: Ce(IV)). For carbon steel parts having simple shapes, decontamination by blasting with zirconia grit is effective in removing major sources of radioactivity at the surface, whereas for carbon steel parts having complicated shapes, major sources of radioactivity can be removed from

The Los Alamos National Laboratory Chemistry and Metallurgy Research Facility upgrades project - A model for waste minimization

International Nuclear Information System (INIS)

Burns, M.L.; Durrer, R.E.; Kennicott, M.A.

1996-07-01

The Los Alamos National Laboratory (LANL) Chemistry and Metallurgy Research (CMR) Facility, constructed in 1952, is currently undergoing a major, multi-year construction project. Many of the operations required under this project (i.e., design, demolition, decontamination, construction, and waste management) mimic the processes required of a large scale decontamination and decommissioning (D ampersand D) job and are identical to the requirements of any of several upgrades projects anticipated for LANL and other Department of Energy (DOE) sites. For these reasons the CMR Upgrades Project is seen as an ideal model facility - to test the application, and measure the success of - waste minimization techniques which could be brought to bear on any of the similar projects. The purpose of this paper will be to discuss the past, present, and anticipated waste minimization applications at the facility and will focus on the development and execution of the project's open-quotes Waste Minimization/Pollution Prevention Strategic Plan.close quotes

How to minimize wastes

International Nuclear Information System (INIS)

Ambolet, M.

1988-10-01

Actions undertaken by the CEA to decrease the stock of natural and depleted uranium are presented in this paper. Various wastes and residues are produced in uranium fabrication. If for some wastes or residues processing methods were found previously, for other storage was the rule. Facing growing problems of safety, bulkiness, and cost new treatments allow to decrease a great amount of wastes. Uranium fabrication cycle, wastes and residues are described. Processing of the different residues of operations and optimization of manufacture are indicated [fr

ALPHA WASTE MINIMIZATION IN TERMS OF VOLUME AND RADIOACTIVITY AT COGEMA'S MELOX AND LA HAGUE PLANTS

International Nuclear Information System (INIS)

ARSLAN, M.; DUMONT, J.C.; LONDRES, V.; PONCELET, F.J.

2003-01-01

This paper describes the management of alpha waste that cannot be stored in surface repositories under current French regulations. The aim of the paper is to provide an overview of COGEMA's Integrated Waste Management Strategy. The topics discussed include primary waste minimization, from facility design to operating feedback; primary waste management by the plant operator, including waste characterization; waste treatment options that led to building waste treatment industrial facilities for plutonium decontamination, compaction and cement solidification; and optimization of industrial tools, which is strongly influenced by safety and financial considerations

Waste Minimization Study on Pyrochemical Reprocessing Processes

International Nuclear Information System (INIS)

Boussier, H.; Conocar, O.; Lacquement, J.

2006-01-01

' new block diagram allowing internal solvent recycling, and self eliminating reactants. This new flowsheet minimizes the quantity of inactive inlet flows that would have inevitably to be incorporated in a final waste form. The study identifies all knowledge gaps to be filled and suggest some possible R and D issues to confirm or infirm the feasibility of the proposed process fittings. (authors)

Actinide removal from wastewater applying waste minimization techniques

International Nuclear Information System (INIS)

Covey, J.R.; Midkiff, W.S.; Cadena, F.

1992-01-01

A major concern at LANL is the large volume of low level radioactive sludge that is generated by the current treatment technology. The plant meets current discharge limits but annually produces 200 55-gallon drums of sludge (approximately 60 tons) during the process of removing only few grants of radioactive isotopes. Most of the sludge results from the coagulants, iron and lime, added at the plant at a concentration of 10,000 parts-per-million (ppm). If the principal actinides in the influent could be separated and reduced to pure metallic form, the annual volume of plutonium would be about the size of a marble and the americium would be about the size of a BB. Waste minimization will be a key design criteria for the new facility. Records of total suspended solids (TSS) in the influent average about 1000 Kg per year (approximately 1 ton). Therefore, the theoretical sludge volume reduction is near 98%. Research is underway to develop and evaluate technologies that achieve the desired removal efficiency with a minimum of produced waste volume

Waste transmutation with minimal fuel cycle long-term risk

Energy Technology Data Exchange (ETDEWEB)

Slessarev, I.; Salvatores, M.; Uematsu, M. [Direction des Reacteurs Nucleaires, Cadarache (France)

1995-10-01

Hybrid systems (source-driven subcritical reactors), are investigated at CEA, mainly from a conceptual point of view, in order to assess their potential to transmute radioactive wastes (mainly long-lived fission products, LLFP) and their potential to insure a minimal long-term radiological risk related both to the fuel inventory inside the system and to the full fuel cycle (mass flows, reprocessing transport, waste disposal). The physics of these systems has been explored and work is in progress both in the field of basic data and INC code validation, in the frame of international collaborations and in the field of conceptual design studies. The most interesting feature of subcritical source-driven system is related to the possibility to obtain an {open_quotes}excess{close_quotes} of neutrons per fission, which can be used to reduce the long-term radiological risk. A specific example will be discussed here.

Uranium Mill Tailings remedial action project waste minimization and pollution prevention awareness program plan

International Nuclear Information System (INIS)

1994-07-01

The purpose of this plan is to establish a waste minimization and pollution prevention awareness (WM/PPA) program for the U.S. Department of Energy's (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project. The program satisfies DOE requirements mandated by DOE Order 5400.1. This plan establishes planning objectives and strategies for conserving resources and reducing the quantity and toxicity of wastes and other environmental releases

Identifying industrial best practices for the waste minimization of low-level radioactive materials

Energy Technology Data Exchange (ETDEWEB)

Levin, V.

1996-04-01

In US DOE, changing circumstances are affecting the management and disposal of solid, low-level radioactive waste (LLW). From 1977 to 1991, the nuclear power industry achieved major reductions in solid waste disposal, and DOE is interested in applying those practices to reduce solid waste at DOE facilities. Project focus was to identify and document commercial nuclear industry best practices for radiological control programs supporting routine operations, outages, and decontamination and decommissioning activities. The project team (DOE facility and nuclear power industry representatives) defined a Work Control Process Model, collected nuclear power industry Best Practices, and made recommendations to minimize LLW at DOE facilities.

Exposure and risk calculations for disposal of wastes having minimal radioactivity

International Nuclear Information System (INIS)

Fields, D.E.

1984-01-01

The US Nuclear Regulatory Commission is currently considering revision of rules 10 CFR 20 and 10 CFR 61, which cover disposal of solid wastes containing minimal activity radioactivity. In support of these revised rules, we have evaluated the consequences of disposing of four waste streams at four types of disposal areas located in three different geographic regions. Consequences are expressed in terms of human exposures and associated health effects. Each geographic region has its own climate and geology. Example waste streams, waste disposal methods, and geographic regions chosen for this study are clearly specified. The PRESTO-II methodology was used to evaluate radionuclide transport and health effects. This methodology was developed to assess radiological impacts to a static local population for a 1000-year period following disposal. The modeling of pathways and processes of migration from the trench to exposed populations included the following considerations: groundwater transport, overland flow, erosion, surface water dilution, resuspension, atmospheric transport, deposition, inhalation, and ingestion of contaminated beef, milk, crops, and water. 9 references, 2 figures, 3 tables

Waste minimization assessment for a manufacturer of baseball bats and golf clubs. Environmental research brief

Energy Technology Data Exchange (ETDEWEB)

Fleischman, M.; Kirsch, F.W.; Maginn, J.C.

1993-09-01

The U.S. Environmental Protection Agency (EPA) has funded a pilot project to assist small and medium-size manufacturers who want to minimize their generation of waste but who lack the expertise to do so. Waste Minimization Assessment Center (WMAC) at the University of Louisville performed an assessment at a plant manufacturing baseball bats and golf clubs -- approximately 1,500,000 bats/yr and 550,000 golf clubs/yr. To make the bats, wood billets are oven-dried and machined to a standard dimension. After sanding they are branded and finished. The golf clubs are made by finishing and assembling purchased heads and shafts. The team's report detailing findings and recommendations, indicated that the most waste, other than rinse water discharged to the publicly owned treatment works (POTW) and wood turnings which are sold, consists of scrap cardboard and paper from the shop and offices, and that the greatest savings, including new income, could be obtained by segregating the cardboard and paper wastes for sale to a local recycler.

Landfill life expectancy with waste reduction/minimization

International Nuclear Information System (INIS)

Klan, M.S.

1990-01-01

Although some minimally acceptable practices are presently undertaken at most landfills to protect human health and safety and the environment, a key question remains. How much effort and resources should be expended to slow the fill-rate of a landfill? The answer depends on the performance and costs of the technical options available, the difficulty and cost of acquiring additional landfill space, and the consequences for remaining landfill lifetime of current and future actions. Toward this end, the paper (1) presents a method for projecting the remaining life of a landfill, including the alternative lifetimes associated with life extension measures; (2) presents a case study of the low-level waste landfill at Los Alamos National Lab.; and (3) illustrates a procedure for determining which measures become cost-effective to adopt as a landfill's space declines

Waste level analysis in a care section with the lean maintenance method to minimize waste in PT. Varia Usaha Beton Gresik

Directory of Open Access Journals (Sweden)

Rochmoeljati Rr.

2017-06-01

Full Text Available The major problem faced by PT. Varia Usaha Beton Gresik is not the maintenance activity according to Standard Operation Procedure (SOP, but the activities conducted without taking into account the waste. The purpose of this study is to examine the waste in the maintenance activities as to minimize it by the lean maintenance method. This is taken on a conveyor belt weigher machine, a bucket conveyor, a concrete mixer, and a machine host. The variable is the flow of treatment by reducing waste and by giving recommendation of improvement. Data collection includes damage data, production data, product disability data, and maintenance activity data. The conclusion is QT-10 waste motion machine takes 532 minutes for waste repair, 45 minutes for waste process, and 90 minutes for waste waiting. Our recommendations include improvement on the information provided, on training and rewards, and on supervisors of the production line.

Treatability study of absorbent polymer waste form for mixed waste treatment

International Nuclear Information System (INIS)

Herrmann, S. D.; Lehto, M. A.; Stewart, N. A.; Croft, A. D.; Kern, P. W.

2000-01-01

A treatability study was performed to develop and characterize an absorbent polymer waste form for application to low level (LLW) and mixed low level (MLLW) aqueous wastes at Argonne National Laboratory-West (ANL-W). In this study absorbent polymers proved effective at immobilizing aqueous liquid wastes in order to meet Land Disposal Restrictions for subsurface waste disposal. Treatment of aqueous waste with absorbent polymers provides an alternative to liquid waste solidification via high-shear mixing with clays and cements. Significant advantages of absorbent polymer use over clays and cements include ease of operations and waste volume minimization. Absorbent polymers do not require high-shear mixing as do clays and cements. Granulated absorbent polymer is poured into aqueous solutions and forms a gel which passes the paint filter test as a non-liquid. Pouring versus mixing of a solidification agent not only eliminates the need for a mixing station, but also lessens exposure to personnel and the potential for spread of contamination from treatment of radioactive wastes. Waste minimization is achieved as significantly less mass addition and volume increase is required of and results from absorbent polymer use than that of clays and cements. Operational ease and waste minimization translate into overall cost savings for LLW and MLLW treatment

Analysis of the matrix structure of the Nuclear Weapons Complex waste minimization and hazard reduction program

International Nuclear Information System (INIS)

Churnetski, S.R.

1991-01-01

Two of the primary goals of this program in waste minimization that the major waste problems facing the Nuclear Weapons Complex (NWC) are being addressed systematically and to prevent duplication of effort by forming an integrated approach across the complex. Production, disposal, and the hazards of both the wastes and the in-process chemicals used were to be studied. The eight waste streams chosen (electroplating, miscellaneous, mixed, plutonium, polymers, solvents, tritium, and uranium) were deemed to be the most serious problems facing the Nuclear Weapons Complex

Development of waste minimization and decontamination technologies at the Idaho Chemical Processing Plant

International Nuclear Information System (INIS)

Ferguson, R.L.; Archibald, K.E.; Demmer, R.L.

1995-01-01

Emphasis on the minimization of decontamination secondary waste has increased because of restrictions on the use of hazardous chemicals and Idaho Chemical Processing Plant (ICPP) waste handling issues. The Lockheed Idaho Technologies Co. (LITCO) Decontamination Development Subunit has worked to evaluate and introduce new performed testing, evaluations, development and on-site demonstrations for a number of novel decontamination techniques that have not yet previously been used at the ICPP. This report will include information on decontamination techniques that have recently been evaluated by the Decontamination Development Subunit

The IFR pyroprocessing for high-level waste minimization

International Nuclear Information System (INIS)

Laidler, J.J.

1993-01-01

The process developed for the recycle of integral fast reactor (IFR) spent fuel utilizes a combination of pyrometallurgical and electrochemical methods and has been termed pyroprocessing. The process has been operated at full scale with simulated spent fuel using nonradioactive fission product elements. A comprehensive demonstration of the pyroprocessing of irradiated IFR fuel will begin later this year. Pyroprocessing involves the anodic dissolution of all the constituent elements of the IFR spent fuel and controlled electrotransport (electrorefining) to separate the actinide elements from the fission products present in the spent fuel. The process be applied to the processing of spent light water reactor (LWR) fuel as well, requiring only the addition of a reduction step to convert the LWR fuel as well, requiring only the addition of a reduction step to convert the LWR oxide fuel to metallic form and a separation step to separate uranium from the transuranic (TRU) elements. The TRU elements are then recovered by electroefining in the same manner as the actinides from the IFR high-level wastes arising from pyroprocessing are virtually free of actinides, and the volume of the wastes is minimized by the intrinsic characteristics of the processing of the processing method

An Exploration of Healthcare Inventory and Lean Management in Minimizing Medical Supply Waste in Healthcare Organizations

Science.gov (United States)

Hicks, Rodney

2013-01-01

The purpose of this study was to understand how lean thinking and inventory management technology minimize expired medical supply waste in healthcare organizations. This study was guided by Toyota's theory of lean and Mintzberg's theory of management development to explain why the problem of medical supply waste exists. Government…

Radwaste minimization successes at Duke Power Company

International Nuclear Information System (INIS)

Lan, C.D.; Johnson, G.T.; Groves, D.C.; Smith, T.A.

1996-01-01

At Duke Power Company, open-quotes Culture Changeclose quotes is a common term that we have used to describe the incredible transformation. We are becoming a cost conscious, customer driven, highly competitive business. Nowhere has this change been more evident then in the way we process and dispose of our solid radioactive waste. With top-down management support, we have used team-based, formalized problem solving methods and have implemented many successful waste minimization programs. Through these programs, we have dramatically increased employees' awareness of the importance of waste minimization. As a result, we have been able to reduce both our burial volumes and our waste processing and disposal costs. In June, 1994, we invited EPRI to conduct assessments of our waste minimization programs at Oconee and Catawba nuclear stations. Included in the assessments were in-depth looks at contamination control, an inventory of items in the plant, the volume of waste generated in the plant and how it was processed, laundry reject data, site waste-handling operations, and plant open-quotes housekeepingclose quotes routines and process. One of the most important aspects of the assessment is the open-quotes dumpster dive,close quotes which is an evaluation of site dry active waste composition by sorting through approximately fifteen bags of radioactive waste. Finally, there was an evaluation of consumable used at each site in order to gain knowledge of items that could be standardized at all stations. With EPRI recommendations, we made several changes and standardized the items used. We have made significant progress in waste reduction. We realize, however, that we are aiming at a moving target and we still have room for improvement. As the price of processing and disposal (or storage) increases, we will continue to evaluate our waste minimization programs

Waste minimization of a process fluid through effective control under various controllers tuning

International Nuclear Information System (INIS)

Younas, M.; Gul, S.; Naveed, S.

2005-01-01

Whenever a process is disturbed either by servo system or regulatory system, the control action is applied to trace the desired point. An efficient controller setting should be selected in order to get speedy response under the pattern or constraints of quality of the product. The effective control action is desired to utilize the maximum of raw material and to minimize the waste. This is a critical problem in cases where the raw material or product is valuable and costly, e.g. pharmaceuticals. This problem has been addressed in this work on a laboratory scale plant. The plant consists of feed tank, pumps, plate and frame heat exchanger and hot water re-circulator tank. The system responses were logged with computer while the controller was tuned with Ziegler-Nichols (Z-N) and Cohen-Coon (C-C) tunings. A detailed study indicates that Ziegler-Nichols Controller tunings is better than Cohen-Coon as waste production was minimized. (author)

1993 Annual report on waste generation and waste minimization progress as required by DOE Order 5400.1, Hanford Site

International Nuclear Information System (INIS)

Kirkendall, J.R.; Engel, J.A.

1994-01-01

More important than waste generation numbers, the pollution prevention and waste minimization successes achieved at Hanford in 1993 have reduced waste and improved operations at the Site. Just a few of these projects are: A small research nuclear reactor, unused and destined for disposal as low level radioactive waste, was provided to a Texas University for their nuclear research program, avoiding 25 cubic meters of waste and saving $116,000. By changing the slope on a asphalt lot in front of a waste storage pad, run-off rainwater was prevented from becoming mixed low level waste water, preventing 40 cubic meters of waste and saving $750,000. Through more efficient electrostatic paint spraying equipment and a solvent recovery system, a paint shop reduced hazardous waste by 3,500 kilograms, saving $90,800. During the demolition of a large decommissioned building, more than 90% of the building's material was recycled by crushing the concrete for use on-Site and selling the steel to an off-Site recycler, avoiding a total of 12,600 metric tons of waste and saving $450,000. Additionally, several site-wide programs have avoided large quantities of waste, including the following: Through expansion of the paper and office waste recycling program which includes paper, cardboard, newspaper, and phone books, 516 metric tons of sanitary waste was reduced, saving $68,000. With the continued success of the excess chemicals program, which finds on-Site and off-Site customers for excess chemical materials, hazardous waste was reduced by 765,000 liters of liquid chemicals and 50 metric tons of solid chemicals, saving over $700,000 in disposal costs

Utilizing environmental management information systems to monitor chemical usage and facilitate waste minimization

Energy Technology Data Exchange (ETDEWEB)

Blazer, T.L.; Kinney, R.W. [Modern Technologies Corporation, Dayton, OH (United States)

1996-10-01

Waste minimization and pollution prevention activities have proven to be valuable to the chemical industry`s and the chemical user`s bottom line. Many companies have found that, with a modest initial capital investment and product modifications, mounds of bureaucratic liability can be removed and substantial cost savings can be realized.

Application of geographic information systems to waste minimization efforts at the national laboratories

International Nuclear Information System (INIS)

Lyttle, T.W.; Smith, D.M.; Burns, M.; Weinrach, J.B.

1993-01-01

At Los Alamos National Laboratory (LANL), facility waste streams tend to be small but highly diverse. Initial characterization of such waste streams is often difficult in part due to a lack of tools to assist the generators themselves in completing such assessments. A methodology has been developed at LANL to allow process knowledgeable field personnel to develop baseline waste generation assessments and to evaluate potential waste minimization technology. This Process Waste Assessment (PWA) system is an application constructed within the Process Modeling System and currently being integrated with the InFoCAD Geographic Information System (GIS). The Process Modeling System (PMS) is an object-oriented, mass balance-based, discrete-event simulation framework written using the Common Lisp Object System (CLOS). Analytical capabilities supported within the PWA system include: complete mass balance specifications, historical characterization of selected waste stream and generation of facility profiles for materials consumption, resource utilization and worker exposure. Development activities include integration with the LANL facilities management Geographic Information System (GIS) and provisions for a Best Available Technologies (BAT) database. The environments used to develop these assessment tools will be discussed in addition to a review of initial implementation results

1994 annual report on waste generation and waste minimization progress as required by DOE Order 5400.1

International Nuclear Information System (INIS)

Irwin, E.F.; Poligone, S.E.

1995-01-01

The Y-12 Plant serves as a key manufacturing technology center for the development and demonstration of unique materials, components, and services of importance to the Department of Energy (DOE) and the nation. This is accomplished through the reclamation and storage of nuclear materials, manufacture of nuclear materials, manufacture of components for the nation's defense capabilities, support to national security programs, and services provided to other customers as approved by DOE. We are recognized by our people, the community, and our customers as innovative, responsive, and responsible. We are a leader in worker health and safety, environmental protection, and stewardship of our national resources. As a DOE facility, Y-12 also supports DOE's waste minimization mission. Data contained in this report represents waste generation in Tennessee

Develop of a model to minimize and to treat waste coming from the chemical laboratories

International Nuclear Information System (INIS)

Chacon Hernandez, M.

2000-01-01

They were investigated and proposed alternative of minimization and treatment of waste organic type coming from chemical laboratories, considering as alternative the disposition for the drainage, the chemical treatment of the waste, the disposition in sanitary fillers, the creation of a cellar to recycle material, the incineration, the distillation and the possibility to establish an agreement with the company Cements INCSA to discard the materials in the oven to cements of this enterprise. the methodology had as first stage the summary of information about the production of residuals for Investigation Center or Academic Unit. For this they were considered the laboratories of investigation of the CICA, CELEQ, CIPRONA, LAYAFA, and the laboratories of teaching of the sections of Organic Chemistry, Inorganic Chemistry, Physicochemical, Pharmacognosy, Drugs Analysis, Physicopharmacy, Histology and Physiology. Additionally, you considers the office of purveyor of the Microbiology School. Subsequently one carries out an analysis of costs to determine which waste constituted most of the waste generated by the University, as for cost and volume. Then, they were carried out classifications of the materials according to chemical approaches, classification of the NFPA and for data of combustion heats. Once carried out this classification and established the current situation of the laboratories considered as for handling and treatment of waste, they proceeded to evaluate and select treatment options and disposition of waste considering advantages and disadvantages as for implementation possibility and cost stops this way a minimization model and treatment that it can be implemented in the University to settle down [es

Evaluation of select trade-offs between ground-water remediation and waste minimization for petroleum refining industry

International Nuclear Information System (INIS)

Andrews, C.D.; McTernan, W.F.; Willett, K.K.

1996-01-01

An investigation comparing environmental remediation alternatives and attendant costs for a hypothetical refinery site located in the Arkansas River alluvium was completed. Transport from the land's surface to and through the ground water of three spill sizes was simulated, representing a base case and two possible levels of waste minimization. Remediation costs were calculated for five alternative remediation options, for three possible regulatory levels and alternative site locations, for four levels of technology improvement, and for eight different years. It is appropriate from environmental and economic perspectives to initiate significant efforts and expenditures that are necessary to minimize the amount and type of waste produced and disposed during refinery operations; or conversely, given expected improvements in technology, is it better to wait until remediation technologies improve, allowing greater environmental compliance at lower costs? The present work used deterministic models to track a light nonaqueous phase liquid (LNAPL) spill through the unsaturated zone to the top of the water table. Benzene leaching from LNAPL to the ground water was further routed through the alluvial aquifer. Contaminant plumes were simulated over 50 yr of transport and remediation costs assigned for each of the five treatment options for each of these years. The results of these efforts show that active remediation is most cost effective after a set point or geochemical quasi-equilibrium is reached, where long-term improvements in technology greatly tilt the recommended option toward remediation. Finally, the impacts associated with increasingly rigorous regulatory levels present potentially significant penalties for the remediation option, but their likelihood of occurrence is difficult to define

Development and characterization of new high-level waste form containing LiCl KCl eutectic salts for achieving waste minimization from pyroprocessing

International Nuclear Information System (INIS)

Cho, Yong Zun; Kim, In Tae; Park, Hwan Seo; Ahn, Byeung Gil; Eun, Hee Chul; Son, Seock Mo; Ah, Su Na

2011-12-01

The purpose of this project is to develop new high level waste (HLW) forms and fabrication processes to dispose of active metal fission products that are removed from electrorefiner salts in the pyroprocessing based fuel cycle. The current technology for disposing of active metal fission products in pyroprocessing involves non selectively discarding of fission product loaded salt in a glass-bonded sodalite ceramic waste form. Selective removal of fission products from the molten salt would greatly minimize the amount of HLW generated and methods were developed to achieve selective separation of fission products during a previous I NERI research project (I NERI 2006 002 K). This I NERI project proceeds from the previous project with the development of suitable waste forms to immobilize the separated fission products. The Korea Atomic Energy Research Institute (KAERI) has focused primarily on developing these waste forms using surrogate waste materials, while the Idaho National Laboratory (INL) has demonstrated fabrication of these waste forms using radioactive electrorefiner salts in hot cell facilities available at INL. Testing and characterization of these radioactive materials was also performed to determine the physical, chemical, and durability properties of the waste forms

Metal decontamination for waste minimization using liquid metal refining technology

International Nuclear Information System (INIS)

Joyce, E.L. Jr.; Lally, B.; Ozturk, B.; Fruehan, R.J.

1993-01-01

The current Department of Energy Mixed Waste Treatment Project flowsheet indicates that no conventional technology, other than surface decontamination, exists for metal processing. Current Department of Energy guidelines require retrievable storage of all metallic wastes containing transuranic elements above a certain concentration. This project is in support of the National Mixed Low Level Waste Treatment Program. Because of the high cost of disposal, it is important to develop an effective decontamination and volume reduction method for low-level contaminated metals. It is important to be able to decontaminate complex shapes where surfaces are hidden or inaccessible to surface decontamination processes and destruction of organic contamination. These goals can be achieved by adapting commercial metal refining processes to handle radioactive and organic contaminated metal. The radioactive components are concentrated in the slag, which is subsequently vitrified; hazardous organics are destroyed by the intense heat of the bath. The metal, after having been melted and purified, could be recycled for use within the DOE complex. In this project, we evaluated current state-of-the-art technologies for metal refining, with special reference to the removal of radioactive contaminants and the destruction of hazardous organics. This evaluation was based on literature reports, industrial experience, plant visits, thermodynamic calculations, and engineering aspects of the various processes. The key issues addressed included radioactive partitioning between the metal and slag phases, minimization of secondary wastes, operability of the process subject to widely varying feed chemistry, and the ability to seal the candidate process to prevent the release of hazardous species

PERAN SIKAP DALAM MEMEDIASI PENGARUH PENGETAHUAN TERHADAP PERILAKU MINIMISASI SAMPAH PADA MASYARAKAT TERBAN, YOGYAKARTA (The Role of Attitude to Mediate The Effect of Knowledge on People’s Waste Minimization Behaviour in Terban, Yogyakarta

Directory of Open Access Journals (Sweden)

Hanif Akhtar

2015-01-01

behaviour. Attitude toward behaviour plays a significant role in behavioural change. This research will focus on one kind of pro-environmental behaviour namely waste minimisastion behaviour. The purpose of this research is to find out the relationship between waste minimization knowledge, attitude, and behaviour. This research was conducted in Kelurahan Terban, RW 02 and RW 11, Yogyakarta in January until February 2014. Total of the subjects are 105. Data were collected using three scales that is: waste minimization behaviour scale, waste minimization attitude scale, and waste minimization knowledge scale. Data were analysed using regression analysis with path analysis model. Sobel Test was used to estimate the mediation effect. Indirect effect analysis showed the indirect effect coeficient was 0,742 with z=3,42 and p <0,01. It is showed that there was an indirect effect of waste minimization knowledge to waste minimization behaviour through waste minimization attitude. Thus, we can conclude that waste minimization attitude mediates the relationship between waste minimization knowledge and waste minimization behaviour.

Application of geographic information systems to waste minimization efforts at Los Alamos National Laboratory

International Nuclear Information System (INIS)

Lyttle, T.W.; Smith, D.M.; Burns, M.; Weinrach, J.B.

1993-01-01

At Los Alamos National Laboratory (LANL), facility waste streams tend to be small but highly diverse. Initial characterization of such waste streams is often difficult in part due to a lack of tools to assist the generators themselves in completing such assessments. A methodology has been developed at LANL to allow process knowledgeable field personnel to develop baseline waste generation assessments and to evaluate potential waste minimization technology. This Process Waste Assessment (PWA) system is an application constructed within the Process Modeling System and currently being integrated with the InFoCAD Geographic Information System (GIS) . The Process Modeling System (PMS) is an object-oriented, mass balance-based, discrete-event simulation framework written using the Common Lisp Object System (CLOS) . Analytical capabilities supported within the PWA system include: complete mass balance specifications, historical characterization of selected waste streams and generation of facility profiles for materials consumption, resource utilization and worker exposure. Development activities include integration with the LANL facilities management Geographic Information System (GIS) and provisions for a Best Available Technologies (BAT) database. The environments used to develop these assessment tools will be discussed in addition to a review of initial implementation results

Good Practice Guide Waste Minimization/Pollution Prevention

Energy Technology Data Exchange (ETDEWEB)

J Dorsey

1999-10-14

This Good Practice Guide provides tools, information, and examples for promoting the implementation of pollution prevention during the design phases of U.S. Department of Energy (DOE) projects. It is one of several Guides for implementing DOE Order 430.1, Life-cycle Asset Management. DOE Order 430.1 provides requirements for DOE, in partnership with its contractors, to plan, acquire, operate, maintain, and dispose of physical assets. The goals of designing for pollution prevention are to minimize raw material consumption, energy consumption, waste generation, health and safety impacts, and ecological degradation over the entire life of the facility (EPA 1993a). Users of this Guide will learn to translate national policy and regulatory requirements for pollution prevention into action at the project level. The Guide was written to be applicable to all DOE projects, regardless of project size or design phase. Users are expected to interpret the Guide for their individual project's circumstances, applying a graded approach so that the effort is consistent with the anticipated waste generation and resource consumption of the physical asset. This Guide employs a combination of pollution prevention opportunity assessment (PPOA) methods and design for environment (DfE) philosophies. The PPOA process was primarily developed for existing products, processes, and facilities. The PPOA process has been modified in this Guide to address the circumstances of the DOE design process as delineated in DOE Order 430.1 and its associated Good Practice Guides. This modified form of the PPOA is termed the Pollution Prevention Design Assessment (P2DA). Information on current nationwide methods and successes in designing for the environment also have been reviewed and are integrated into this guidance.

Waste minimization through process optimization/integration and resource management at eco-friendly Heavy Water Plants

International Nuclear Information System (INIS)

Nageshri, Jagdish; Gupta, S.K.

2004-01-01

Heavy Water Board has celebrated 2003 as Environmental Conservation Year captivating a range of enviro-friendly measures. This article attempts to give a brief overview of the outcome of systems and adapted procedures for waste minimization through process integration and resource management at Heavy Water Plants

Process innovations to minimize waste volumes at Savannah River

International Nuclear Information System (INIS)

Doherty, J.P.

1986-01-01

In 1983 approximately 1.6 x 10 3 m 3 (427,000 gallons) of radioactive salt solution were decontaminated in a full-scale demonstration. The cesium decontamination factor (DF) was in excess of 4 x 10 4 vs. a goal of 1 x 10 4 . Data from this test were combined with pilot data and used to design the permanent facilities currently under construction. Startup of the Salt Decontamination Process is scheduled for 1987 and will decontaminate 2 x 10 4 m 3 (5.2 million gallons) of radioactive salt solution and generate 2 x 10 3 m 3 (520,000 gallons) of concentrated and washed precipitate per year. The Defense Waste Processing Facility (DWPF) will begin processing this concentrate in the Precipitate Hydrolysis Process starting in 1989. Laboratory data using simulated salt solution and nonradioactive cesium are being used to design this process. A 1/5-scale pilot plant is under construction and will be used to gain large-scale operating experience using nonradioactive simulants. This pilot plant is scheduled to startup in early 1987. The incentives to reduce the volume of waste that must be treated are self-evident. At Savannah River process development innovations to minimize the DWPF feed volumes have directly improved the economics of the process. The integrity of the final borosilicate glass water form has not been compromised by these developments. Many of the unit operations are familiar to chemical engineers and were put to use in a unique environment. As a result, tax dollars have been saved, and the objective of safely disposing of the nation's high-level defense waste has moved forward

Clearance measurements as a tool for waste minimization during decommissioning

International Nuclear Information System (INIS)

Konneus, Patrick; Andersson, Veronica; Lindberg, Maria

2012-01-01

Clearance, exemption or free release of material from regulatory control are three ways of expressing the same thing, minimizing the amount of waste that needs disposal as radioactive waste and therefor preserving a repository as a national asset. Studsvik Nuclear has utilized the former full body measurement cell as a shielded compartment used for gamma spectroscopy measurements of materials that may be subject to clearance. The cell was moved from its original position by heavy lifting and transport, as it was transported in one piece weighing 53 tonnes. The facility has basically 4 parts, the cell in which the item is place, the rotating table that rotates the item to get the best possible measurement, the ISOCS that measure the gamma rays and the operator room from which the facility runs. The detector is a BEGe with a relative efficiency of 50 % and is provided by Canberra. Apex is used as software for acquisition, calibration and data storage. The cell can take Bergloefs boxes up to a volume of 1.2m 3 and a weight of 3 tonnes can be rotated on the table. Other standard geometries are drums of 100 or 200 liters. The shielding improves the background radiation to a level where a measurement time of only 1200 s for a standard object (100 L/200 L drum, Bergloefs box) is needed. This means a high daily capacity of measurements. During 2011 measurements have been done on several different materials and together with sampling for alpha emitting nuclides the material has been released from regulatory control and either recycled or disposed of in a standard landfill or a land fill for hazardous waste. The materials released are copper from cable shredding that was measured, samples and recycled about 14 tonnes, titanium tubes about 35 tonnes also recycled and fiberglass/epoxy that has been released for waste treatment in a non-radioactive treatment facility. Measurements have also been done of waste with complex geometries. (authors)

Proceedings of pollution prevention and waste minimization tools workshop

International Nuclear Information System (INIS)

1995-01-01

Pollution Prevention (P2) has evolved into one of DOE's sprime strategies to meet environmental, fiscal, and worker safety obligations. P2 program planning, opportunity identification, and implementation tools were developed under the direction of the Waste Minimization Division (EM-334). Forty experts from EM, DP, ER and DOE subcontractors attended this 2-day workshop to formulate the incentives to drive utilization of these tools. Plenary and small working group sessions were held both days. Working Group 1 identified incentives to overcoming barriers in the area of P2 program planning and resource allocation. Working Group 2 identified mechanisms to drive the completion of P2 assessments and generation of opportunities. Working Group 3 compiled and documented a broad range of potential P2 incentives that address fundamental barriers to implementation of cost effective opportunities

Gunite and associated tanks remediation project recycling and waste minimization effort

International Nuclear Information System (INIS)

Van Hoesen, S.D.; Saunders, A.D.

1998-05-01

The Department of Energy's Environmental Management Program at Oak Ridge National Laboratory has initiated clean up of legacy waste resulting from the Manhattan Project. The gunite and associated tanks project has taken an active pollution prevention role by successfully recycling eight tons of scrap metal, reusing contaminated soil in the Area of Contamination, using existing water (supernate) to aid in sludge transfer, and by minimizing and reusing personal protective equipment (PPE) and on-site equipment as much as possible. Total cost savings for Fiscal Year 1997 activities from these efforts are estimated at $4.2 million dollars

Systematic process synthesis and design methods for cost effective waste minimization

International Nuclear Information System (INIS)

Biegler, L.T.; Grossman, I.E.; Westerberg, A.W.

1995-01-01

We present progress on our work to develop synthesis methods to aid in the design of cost effective approaches to waste minimization. Work continues to combine the approaches of Douglas and coworkers and of Grossmann and coworkers on a hierarchical approach where bounding information allows it to fit within a mixed integer programming approach. We continue work on the synthesis of reactors and of flexible separation processes. In the first instance, we strive for methods we can use to reduce the production of potential pollutants, while in the second we look for ways to recover and recycle solvents

Systematic process synthesis and design methods for cost effective waste minimization

Energy Technology Data Exchange (ETDEWEB)

Biegler, L.T.; Grossman, I.E.; Westerberg, A.W. [Carnegie Mellon Univ., Pittsburgh, PA (United States)

1995-12-31

We present progress on our work to develop synthesis methods to aid in the design of cost effective approaches to waste minimization. Work continues to combine the approaches of Douglas and coworkers and of Grossmann and coworkers on a hierarchical approach where bounding information allows it to fit within a mixed integer programming approach. We continue work on the synthesis of reactors and of flexible separation processes. In the first instance, we strive for methods we can use to reduce the production of potential pollutants, while in the second we look for ways to recover and recycle solvents.

Minimization of the volume and Pu content of the waste generated at a plutonium fuel fabrication plant

International Nuclear Information System (INIS)

Pauwels, H.

1992-01-01

The amounts of waste generated during 1987, 1989 and a past reference period have been reported in great detail. The main conclusions which can be drawn from these figures are: (i) for all kinds of waste, the waste-to-product ratio has decreased very substantially during the past few years. This reduction results partly from a scale effect, i.e. the better load factor of the plant, and partly from Belgonucleare's continuous effort to minimize the radioactive waste arisings; (ii) the ratio of the Pu content of the waste to the total Pu throughput of the plant has also decreased substantially; (iii) the mean Pu content of the solid Pu contaminated waste equals 1.39 g Pu per unit volume of 25 l. Only for a small fraction of this waste (<5% by volume) does the Pu content exceed 5 g per unit volume of 25 l; (iv) even after the implementation of waste reducing measures, some 45% of the solid Pu contaminated waste is generated by operations which involve the handling and transfer of powders. Finally, some 63% of the total amount of Pu in the waste can be imputed to these operations

Development of a methodology for minimizing 241Am waste from radioactive lightning rod

International Nuclear Information System (INIS)

Araujo, Valeska Peres de; Sousa, Alvaro S.F. de; Ferreira, Elizabeth de M.M.; Brandao, Luis Eduardo Barreira

2011-01-01

In 1989, the Brazilian National Nuclear Energy Commission, CNEN, cancelled the authorization to produce and install lightning rods that employed radioisotopes sources, which since then have been collected and treated as radioactive waste. The main radioisotopes employed as a radioactive source onto the lightning rods were the 241 Am and 226 Ra, being the 241 Am the most used due to its lower production cost. In the radioactive lightning rods the sources are first fixed in a stainless steel support, then sealed and fixed on the 30 cm length lightning rod body by rivets. These captors when constantly exposed to rain and winds can release the radioactive material and then contaminate the device, generating a greater volume of waste.The focus of this preliminary study is to develop a methodology to minimize the final volume of waste by removing the source followed by a chemical treatment to clean the lightning rods. Ultrasound techniques associated with suitable solvents as water, acids and chelates was applied. Gamma spectrometry was used to analyze the material after each decontamination step. In agreement to Regulations of Radiological Protection, the results indicate that it is possible to dispose of the lightning rod after the source removal followed by a suitable treatment and reducing this way the volume of waste. (author)

Pollution Prevention/Waste Minimization

International Nuclear Information System (INIS)

Fowler, Kimberly M.; Hyman, Marvin H.

2002-01-01

This chapter offers pollution prevention techniques for design, industrial process, maintenance, and environmental remediation activities. It provides examples of waste reduction, tools for identifying pollution prevention opportunities, and ways of calculating the payback or return on investment associated with the opportunities

Waste minimization promotes biophysical treatment of complex petrochemical wastes in Israel

Energy Technology Data Exchange (ETDEWEB)

Lebel, A [Invirotreat International Ltd., Fulleron, CA (United States); Raveh, A [Raveh Ecology Ltd., Haifa (Israel)

1994-12-31

This work describes a full-scale waste treatment system which was put into operation in a petrochemical manufacturing plant in Israel for the purpose of detoxifying its complex organic waste stream. The treatment plant design incorporates an innovative waste management approach to accommodate the limited space allocated for the facility. Initial performance data indicate a high efficient inorganic waste reduction. 4 refs., 6 figs., 2 tabs.

Waste minimization promotes biophysical treatment of complex petrochemical wastes in Israel

Energy Technology Data Exchange (ETDEWEB)

Lebel, A. [Invirotreat International Ltd., Fulleron, CA (United States); Raveh, A. [Raveh Ecology Ltd., Haifa (Israel)

1993-12-31

This work describes a full-scale waste treatment system which was put into operation in a petrochemical manufacturing plant in Israel for the purpose of detoxifying its complex organic waste stream. The treatment plant design incorporates an innovative waste management approach to accommodate the limited space allocated for the facility. Initial performance data indicate a high efficient inorganic waste reduction. 4 refs., 6 figs., 2 tabs.

Cleaner production: Minimizing hazardous waste in Indonesia

Energy Technology Data Exchange (ETDEWEB)

Bratasida, D.L. [BAPEDAL, Jakarta (Indonesia)

1996-12-31

In the second long-term development plan, industry plays a significant role in economic growth. In Indonesia, industries grow very fast; such fast growth can adversely effect the environment. Exploitation of assets can mean depletion of natural resources and energy, which, if incorrectly managed, can endanger human life and the environment. The inefficient use of natural resources will accelerate their exhaustion and generate pollution, resulting in environmental damage and threats to economic development and human well being. In recent years, changes in the approach used to control pollution have been necessary because of the increasing seriousness of the problems. Initial environmental management strategies were based on a carrying capacity approach; the natural assimilative capacity accommodated the pollution load that was applied. The environmental management strategies adopted later included technologies applied to the end of the discharge point (so-called {open_quotes}end-of-pipe{close_quotes} treatments). Until now, environmental management strategies focused on end-of-pipe approaches that control pollutants after they are generated. These approaches concentrate on waste treatment and disposal to control pollution and environmental degradation. However, as industry develops, waste volumes continue to increase, thereby creating further environmental problems. In addition, the wastes produced tend to have more complex characteristics and are potentially more difficult to treat for a reasonable cost. There are often technical and financial obstacles to regulatory compliance if waste treatment is relied on as the only means of achieving environmental objectives. Consequently, the reactive end-of-pipe treatment approach has been changed to a proactive cleaner production approach. This approach is based on the concept of sustainable development and is designed to prevent pollution as well as to protect natural resources and the quality of the environment.

Collection and Segregation of Radioactive Waste. Principals for Characterization and Classification of Radioactive Waste

International Nuclear Information System (INIS)

Dziewinska, K.M.

1998-01-01

Radioactive wastes are generated by all activities which utilize radioactive materials as part of their processes. Generally such activities include all steps in the nuclear fuel cycle (for power generation) and non-fuel cycle activities. The increasing production of radioisotopes in a Member State without nuclear power must be accompanied by a corresponding development of a waste management system. An overall waste management scheme consists of the following steps: segregation, minimization, treatment, conditioning, storage, transport, and disposal. To achieve a satisfactory overall management strategy, all steps have to be complementary and compatible. Waste segregation and minimization are of great importance mainly because they lead to cost reduction and reduction of dose commitments to the personnel that handle the waste. Waste characterization plays a significant part in the waste segregation and waste classification processes, it implicates required waste treatment process including the need for the safety assessment of treatment conditioning and storage facilities

Minimizing waste (off-cuts using cutting stock model: The case of one dimensional cutting stock problem in wood working industry

Directory of Open Access Journals (Sweden)

Gbemileke A. Ogunranti

2016-09-01

Full Text Available Purpose: The main objective of this study is to develop a model for solving the one dimensional cutting stock problem in the wood working industry, and develop a program for its implementation. Design/methodology/approach: This study adopts the pattern oriented approach in the formulation of the cutting stock model. A pattern generation algorithm was developed and coded using Visual basic.NET language. The cutting stock model developed is a Linear Programming (LP Model constrained by numerous feasible patterns. A LP solver was integrated with the pattern generation algorithm program to develop a one - dimensional cutting stock model application named GB Cutting Stock Program. Findings and Originality/value: Applying the model to a real life optimization problem significantly reduces material waste (off-cuts and minimizes the total stock used. The result yielded about 30.7% cost savings for company-I when the total stock materials used is compared with the former cutting plan. Also, to evaluate the efficiency of the application, Case I problem was solved using two top commercial 1D-cutting stock software.  The results show that the GB program performs better when related results were compared. Research limitations/implications: This study round up the linear programming solution for the number of pattern to cut. Practical implications: From Managerial perspective, implementing optimized cutting plans increases productivity by eliminating calculating errors and drastically reducing operator mistakes. Also, financial benefits that can annually amount to millions in cost savings can be achieved through significant material waste reduction. Originality/value: This paper developed a linear programming one dimensional cutting stock model based on a pattern generation algorithm to minimize waste in the wood working industry. To implement the model, the algorithm was coded using VisualBasic.net and linear programming solver called lpsolvedll (dynamic

The Research Status for Decommissioning and Radioactive Waste Minimization of HTR-PM

International Nuclear Information System (INIS)

Li Wenqian; Li Hong; Cao Jianzhu; Tong Jiejuan

2014-01-01

Decommissioning of the high-temperature gas-cooled reactor-pebble bed module (HTR-PM) as a part of the nuclear power plant, is very important during the early design stage of the construction, and it is under study and research currently. This article gives a thorough description of the current decommissioning study status of HTR-PM. Since HTR-PM has its features such as adopting a large amount of graphite, the waste inventory and characterization will be quite different from other type of reactors, new researches should be carried out and good lessons of practices and experiences should be learned from international other reactors, especially the AVR. Based on the new international regulations and Chinese laws, a comprehensive decommissioning program should be proposed to guarantee the HTR-PM will succeed in every stage of the decommissioning, such as defueling, decontamination, dismantling, demolition, waste classification and disposal, etc. In the meantime, the minimization of the radioactive waste should be taken into account during the whole process - before construction, during operation and after shut down. In this article, the decommissioning strategy and program conception of HTR-PM will be introduced, the radiation protection consideration during the decommissioning activities will be discussed, and the research on the activation problem of the decommissioning graphite will be introduced. (author)

Petroleum industry is cleaning up its act -- Self-cleaning filters to maximize profits, minimize waste and reduce liability

International Nuclear Information System (INIS)

Williams, D.

2004-01-01

Recent steps taken by the petroleum industry to control end-of-pipe pollution and to minimize waste at the source by changing over to self-cleaning, backwashable filters instead of the traditional disposable filters such as bags or cartridges, are discussed. Various self-cleaning filter systems and their advantages are described, using REACTOGARD which provides total protection for catalysts in fixed-bed reactors and EROSIONGARD, used in fluidized catalytic crackers, as examples. Both filter systems have been developed by RPA Process Technologies, Inc., a global leader in industrial filtration systems. Major advantages attributed to self-cleaning filters include significantly reduced costs through reducing the number of catalyst change-out cycles, maximized platform productivity through virtually eliminating the risk of plugged wells, reduced waste through ability to recycle cleaning liquids, increased profits through shorter return-on-investment cycles, reduced emissions and reduced future liability through higher safety in the workplace; also reduced pollution of landfill sites. 1 photo

Good Practice Guide Waste Minimization/Pollution Prevention; TOPICAL

International Nuclear Information System (INIS)

J Dorsey

1999-01-01

This Good Practice Guide provides tools, information, and examples for promoting the implementation of pollution prevention during the design phases of U.S. Department of Energy (DOE) projects. It is one of several Guides for implementing DOE Order 430.1, Life-cycle Asset Management. DOE Order 430.1 provides requirements for DOE, in partnership with its contractors, to plan, acquire, operate, maintain, and dispose of physical assets. The goals of designing for pollution prevention are to minimize raw material consumption, energy consumption, waste generation, health and safety impacts, and ecological degradation over the entire life of the facility (EPA 1993a). Users of this Guide will learn to translate national policy and regulatory requirements for pollution prevention into action at the project level. The Guide was written to be applicable to all DOE projects, regardless of project size or design phase. Users are expected to interpret the Guide for their individual project's circumstances, applying a graded approach so that the effort is consistent with the anticipated waste generation and resource consumption of the physical asset. This Guide employs a combination of pollution prevention opportunity assessment (PPOA) methods and design for environment (DfE) philosophies. The PPOA process was primarily developed for existing products, processes, and facilities. The PPOA process has been modified in this Guide to address the circumstances of the DOE design process as delineated in DOE Order 430.1 and its associated Good Practice Guides. This modified form of the PPOA is termed the Pollution Prevention Design Assessment (P2DA). Information on current nationwide methods and successes in designing for the environment also have been reviewed and are integrated into this guidance

Regulatory Strategies To Minimize Generation Of Regulated Wastes From Cleanup, Continued Use Or Decommissioning Of Nuclear Facilities Contaminated With Polychlorinated Biphenyls (PCBS) - 11198

International Nuclear Information System (INIS)

Lowry, N.

2010-01-01

Disposal costs for liquid PCB radioactive waste are among the highest of any category of regulated waste. The high cost is driven by the fact that disposal options are extremely limited. Toxic Substances Control Act (TSCA) regulations require most liquids with PCBs at concentration of (ge) 50 parts-per-million to be disposed by incineration or equivalent destructive treatment. Disposal fees can be as high as $200 per gallon. This figure does not include packaging and the cost to transport the waste to the disposal facility, or the waste generator's labor costs for managing the waste prior to shipment. Minimizing the generation of liquid radioactive PCB waste is therefore a significant waste management challenge. PCB spill cleanups often generate large volumes of waste. That is because the removal of PCBs typically requires the liberal use of industrial solvents followed by a thorough rinsing process. In a nuclear facility, the cleanup process may be complicated by the presence of radiation and other occupational hazards. Building design and construction features, e.g., the presence of open grating or trenches, may also complicate cleanup. In addition to the technical challenges associated with spill cleanup, selection of the appropriate regulatory requirements and approach may be challenging. The TSCA regulations include three different sections relating to the cleanup of PCB contamination or spills. EPA has also promulgated a separate guidance policy for fresh PCB spills that is published as Subpart G of 40 CFR 761 although it is not an actual regulation. Applicability is based on the circumstances of each contamination event or situation. Other laws or regulations may also apply. Identification of the allowable regulatory options is important. Effective communication with stakeholders, particularly regulators, is just as important. Depending on the regulatory path that is taken, cleanup may necessitate the generation of large quantities of regulated waste

Waste minimization value engineering workshop for the Los Alamos National Laboratory Omega West Reactor Decommissioning Project

International Nuclear Information System (INIS)

Hartnett, S.; Seguin, N.; Burns, M.

1995-01-01

The Los Alamos National Laboratory Pollution Prevention Program Office sponsored a Value Engineering (VE) Workshop to evaluate recycling options and other pollution prevention and waste minimization (PP/WMin) practices to incorporate into the decommissioning of the Omega West Reactor (OWR) at the laboratory. The VE process is an organized, systematic approach for evaluating a process or design to identify cost saving opportunities, or in this application, waste reduction opportunities. This VE Workshop was a facilitated process that included a team of specialists in the areas of decontamination, decommissioning, PP/WMin, cost estimating, construction, waste management, recycling, Department of Energy representatives, and others. The uniqueness of this VE Workshop was that it used an interdisciplinary approach to focus on PP/WMin practices that could be included in the OWR Decommissioning Project Plans and specifications to provide waste reduction. This report discusses the VE workshop objectives, summarizes the OWR decommissioning project, and describes the VE workshop activities, results, and lessons learned

Waste minimization value engineering workshop for the Los Alamos National Laboratory Omega West Reactor Decommissioning Project

Energy Technology Data Exchange (ETDEWEB)

Hartnett, S.; Seguin, N. [Benchmark Environmental Corp., Albuquerque, NM (United States); Burns, M. [Los Alamos National Lab., NM (United States)

1995-12-31

The Los Alamos National Laboratory Pollution Prevention Program Office sponsored a Value Engineering (VE) Workshop to evaluate recycling options and other pollution prevention and waste minimization (PP/WMin) practices to incorporate into the decommissioning of the Omega West Reactor (OWR) at the laboratory. The VE process is an organized, systematic approach for evaluating a process or design to identify cost saving opportunities, or in this application, waste reduction opportunities. This VE Workshop was a facilitated process that included a team of specialists in the areas of decontamination, decommissioning, PP/WMin, cost estimating, construction, waste management, recycling, Department of Energy representatives, and others. The uniqueness of this VE Workshop was that it used an interdisciplinary approach to focus on PP/WMin practices that could be included in the OWR Decommissioning Project Plans and specifications to provide waste reduction. This report discusses the VE workshop objectives, summarizes the OWR decommissioning project, and describes the VE workshop activities, results, and lessons learned.

On the technical development to minimize the quantity of solid wastes in a uranium conversion

International Nuclear Information System (INIS)

Otomura, Keiichiro; Ogura, Yoshikazu; Fujisaki, Sakae

1987-01-01

We have developed the new process of treating the waste liquor from a uranium conversion at Ningyo Toge Works PNC, Japan. This process consists of neutralizing precipitation, solid liquid separation, distillation and adsorption. At a neutralizing precipitation step a magnesium oxide is added in the waste liquor containing uranium and fluorine. Most of the uranium and fluorine in the waste liquor precipitate as magnesium compounds. A sulfuric acid is added to the precipitate separated by a filter to dissolve. The resulting solution is then distilled to recover a hydrofluoric acid as a distillate. Uranium is recovered from a residue by an anion exchange method. The recoverd fluorine and uranium are recycled to the main process of conversion. The filtrate separated at the precipitation step is then passed through adsorbing columns. The residual fluorine and uranium in the filtrate were adsorbed and removed by the chelating resine which selectively adsorb the uranium and fluorine. After that the treated waste liquor is discharged out of the plant. This process has merits of being able to minimize the quantity of solid waste in comparison with the conventional process and to recover uranium and fluorine. This process can also be applied to uranium reconversion process from uranium hexafluoride to uranium oxide and to uranium metal production process, which produce the same kind of waste liquor. (author)

Characterization of waste streams and suspect waste from largest Los Alamos National Laboratory generators

International Nuclear Information System (INIS)

Soukup, J.D.; Erpenbeck, G.J.

1995-01-01

A detailed waste stream characterization of 4 primary generators of low level waste at LANL was performed to aid in waste minimization efforts. Data was compiled for these four generators from 1988 to the present for analyses. Prior waste minimization efforts have focused on identifying waste stream processes and performing source materials substitutions or reductions where applicable. In this historical survey, the generators surveyed included an accelerator facility, the plutonium facility, a chemistry and metallurgy research facility, and a radiochemistry research facility. Of particular interest in waste minimization efforts was the composition of suspect low level waste in which no radioactivity is detected through initial survey. Ultimately, this waste is disposed of in the LANL low level permitted waste disposal pits (thus filling a scarce and expensive resource with sanitary waste). Detailed analyses of the waste streams from these 4 facilities, have revealed that suspect low level waste comprises approximately 50% of the low level waste by volume and 47% by weight. However, there are significant differences in suspect waste density when one considers the radioactive contamination. For the 2 facilities that deal primarily with beta emitting activation and spallation products (the radiochemistry and accelerator facilities), the suspect waste is much lower density than all low level waste coming from those facilities. For the 2 facilities that perform research on transuranics (the chemistry and metallurgy research and plutonium facilities), suspect waste is higher in density than all the low level waste from those facilities. It is theorized that the low density suspect waste is composed primarily of compactable lab trash, most of which is not contaminated but can be easily surveyed. The high density waste is theorized to be contaminated with alpha emitting radionuclides, and in this case, the suspect waste demonstrates fundamental limits in detection

Waste segregation procedures and benefits

International Nuclear Information System (INIS)

Fish, J.D.; Massey, C.D.; Ward, S.J.

1990-01-01

Segregation is a critical first step in handling hazardous and radioactive materials to minimize the generation of regulated wastes. In addition, segregation can significantly reduce the complexity and the total cost of managing waste. Procedures at Sandia National Laboratories, Albuquerque require that wastes be segregated, first, by waste type (acids, solvents, low level radioactive, mixed, classified, etc.). Higher level segregation requirements, currently under development, are aimed at enhancing the possibilities for recovery, recycle and reapplication; reducing waste volumes; reducing waste disposal costs, and facilitating packaging storage, shipping and disposal. 2 tabs

Minimizing generator liability while disposing hazardous waste

International Nuclear Information System (INIS)

Canter, L.W.; Lahlou, M.; Pendurthi, R.P.

1991-01-01

Potential liabilities associated with hazardous waste disposal are related to waste properties, disposal practices and the potential threat to people and the environment in case of a pollutant release. Based on various regulations, these liabilities are enforceable and longstanding. A methodology which can help hazardous waste generators select a commercial disposal facility with a relatively low risk of potential liability is described in this paper. The methodology has two parts. The first part has 8 categories encompassing 30 factors common to all facilities, and the second part includes one category dealing with 5 factors on specific wastes and treatment/disposal technologies. This two-part evaluation feature enables the user to adapt the methodology to any type of waste disposal. In determining the scores for the factors used in the evaluation. an unranked paired comparison technique with slight modifications was used to weight the relative importance of the individual factors. In the methodology it is possible for the user to redefine the factors and change the scoring system. To make the methodology more efficient, a user-friendly computer program has been developed; the computer program is written so that desired changes in the methodology can be readily implemented

Minimizing Onsite Organic Household Left-Over Waste: The Emission Benefits of Keeping Pet Rabbits.

Directory of Open Access Journals (Sweden)

Konstantinos P. Tsagarakis

2017-09-01

Full Text Available As waste management is becoming all the more crucial, this study investigates the way in which house left-over organic waste can be better managed on site, in order to minimize the off-site treatment cost and maximize environmental performance. For the implementation of this research, a full year measurement was recorded, showing the organic leftover waste food intake of two rabbits in a household of four. The organic food, collected in two separate baskets suitable for composting—though one for rabbit intake—was 168.5 kg in total, plus 68.8 kg, which was delivered directly to the composting bin, along with food remains and rabbit feces. The results show that, over the examined year, a total of up to 0.417 metric tons of CO2 equivalent per year emissions was avoided, suggesting that if 30 houses were to apply this methodology, one garbage truck journey per year would be saved. Overall, this study suggests that better information and environmental awareness can result in on-site, low cost, individual management of recyclable organic material, which would assist with the decrease in the cost of management, along with increased environmental performance.

Safety control and minimization of radioactive wastes

International Nuclear Information System (INIS)

Wang Jinming; Rong Feng; Li Jinyan; Wang Xin

2010-01-01

Compared with the developed countries, the safety control and minimization of the radwastes in China are under-developed. The research of measures for the safety control and minimization of the radwastes is very important for the safety control of the radwastes, and the reduction of the treatment and disposal cost and environment radiation hazards. This paper has systematically discussed the safety control and the minimization of the radwastes produced in the nuclear fuel circulation, nuclear technology applications and the process of decommission of nuclear facilities, and has provided some measures and methods for the safety control and minimization of the radwastes. (authors)

Secondary waste minimization in analytical methods

International Nuclear Information System (INIS)

Green, D.W.; Smith, L.L.; Crain, J.S.; Boparai, A.S.; Kiely, J.T.; Yaeger, J.S.; Schilling, J.B.

1995-01-01

The characterization phase of site remediation is an important and costly part of the process. Because toxic solvents and other hazardous materials are used in common analytical methods, characterization is also a source of new waste, including mixed waste. Alternative analytical methods can reduce the volume or form of hazardous waste produced either in the sample preparation step or in the measurement step. The authors are examining alternative methods in the areas of inorganic, radiological, and organic analysis. For determining inorganic constituents, alternative methods were studied for sample introduction into inductively coupled plasma spectrometers. Figures of merit for the alternative methods, as well as their associated waste volumes, were compared with the conventional approaches. In the radiological area, the authors are comparing conventional methods for gross α/β measurements of soil samples to an alternative method that uses high-pressure microwave dissolution. For determination of organic constituents, microwave-assisted extraction was studied for RCRA regulated semivolatile organics in a variety of solid matrices, including spiked samples in blank soil; polynuclear aromatic hydrocarbons in soils, sludges, and sediments; and semivolatile organics in soil. Extraction efficiencies were determined under varying conditions of time, temperature, microwave power, moisture content, and extraction solvent. Solvent usage was cut from the 300 mL used in conventional extraction methods to about 30 mL. Extraction results varied from one matrix to another. In most cases, the microwave-assisted extraction technique was as efficient as the more common Soxhlet or sonication extraction techniques

Microwave technology for waste management applications: Treatment of discarded electronic circuitry

Energy Technology Data Exchange (ETDEWEB)

Wicks, G.G. [Westinghouse Savannah River Technology Center, Aiken, SC (United States); Clark, D.E.; Schulz, R.L. [Univ. of Florida, Gainesville, FL (United States)

1997-01-01

Significant quantities of hazardous wastes are generated from a multitude of processes and products in today`s society. This waste inventory is not only very large and diverse, but is also growing at an alarming rate. In order to minimize the dangers presented by constituents in these wastes, microwave technologies are being investigated to render harmless the hazardous components and ultimately, to minimize their impact to individuals and the surrounding environment.

Application of lean six sigma to waste minimization in cigarette paper industry

Science.gov (United States)

Syahputri, K.; Sari, R. M.; Anizar; Tarigan, I. R.; Siregar, I.

2018-02-01

The cigarette paper industry is one of the industry that is always experiencing increasing demand from consumers. Consumer expectations for the products produced also increased both in terms of quality and quantity. The company continuously improves the quality of its products by trying to minimize nonconformity, waste and improve the efficiency of the whole production process of the company. In this cigarette industry, there is a disability whose value is above the company’s defect tolerance that is 10% of the production amount per month. Another problem also occurs in the production time is too long due to the many activities that are not value added (non value added activities) on the production floor. To overcome this problem, it is necessary to improve the production process of cigarette paper and minimize production time by reducing non value added activities. Repairs done with Lean Six Sigma. Lean Six Sigma is a combination of Lean and Six Sigma concept with DMAIC method (Define, Measure, Analyze, Improve, Control). With this Lean approach, obtained total production time of 1479.13 minutes proposal with cycle efficiency process increased by 12.64%.

A Novel and Cost Effective Approach to the Decommissioning and Decontamination of Legacy Glove Boxes - Minimizing TRU Waste and Maximizing LLW Waste - 13634

Energy Technology Data Exchange (ETDEWEB)

Pancake, Daniel; Rock, Cynthia M.; Creed, Richard [Argonne National Laboratory, 9700 South Cass Avenue, Lemont, IL 60439 (United States); Donohoue, Tom; Martin, E. Ray; Mason, John A. [ANTECH Corporation 9050 Marshall Court, Westminster, CO, 80031 (United States); Norton, Christopher J.; Crosby, Daniel [Environmental Alternatives, Inc., 149 Emerald Street, Suite R, Keene, NH 03431 (United States); Nachtman, Thomas J. [InstaCote, Inc., 160 C. Lavoy Road, Erie, MI, 48133 (United States)

2013-07-01

determine the TRU content of the boxes by assessing the activity of Am-241 (59 keV) and Pu-241 (414 keV). Using the data generated it was possible for qualified subject matter experts (SME) to assess that the gloveboxes could be consigned for disposition as LLW and not as TRU. Once this determination was assessed and accepted the gloveboxes were prepared for final disposition to the Nevada National Security Site (NNSS) - formerly the Nevada Test Site (NTS). This preparation involved fixing any remaining radioactive contamination within the gloveboxes by filling them with a foam compound, prior to transportation. Once the remaining contamination was fixed the gloveboxes were removed from the laboratory and prepared for transported by road to NNSS. This successful glovebox decontamination and decommissioning process illustrates the means by which TRU waste generation has been minimized, LLW generation has been maximized, and risk has been effectively managed. The process minimizes the volume of TRU waste and reduced the decommissioning time with significant cost savings as the result. (authors)

A Novel and Cost Effective Approach to the Decommissioning and Decontamination of Legacy Glove Boxes - Minimizing TRU Waste and Maximizing LLW Waste - 13634

International Nuclear Information System (INIS)

Pancake, Daniel; Rock, Cynthia M.; Creed, Richard; Donohoue, Tom; Martin, E. Ray; Mason, John A.; Norton, Christopher J.; Crosby, Daniel; Nachtman, Thomas J.

2013-01-01

determine the TRU content of the boxes by assessing the activity of Am-241 (59 keV) and Pu-241 (414 keV). Using the data generated it was possible for qualified subject matter experts (SME) to assess that the gloveboxes could be consigned for disposition as LLW and not as TRU. Once this determination was assessed and accepted the gloveboxes were prepared for final disposition to the Nevada National Security Site (NNSS) - formerly the Nevada Test Site (NTS). This preparation involved fixing any remaining radioactive contamination within the gloveboxes by filling them with a foam compound, prior to transportation. Once the remaining contamination was fixed the gloveboxes were removed from the laboratory and prepared for transported by road to NNSS. This successful glovebox decontamination and decommissioning process illustrates the means by which TRU waste generation has been minimized, LLW generation has been maximized, and risk has been effectively managed. The process minimizes the volume of TRU waste and reduced the decommissioning time with significant cost savings as the result. (authors)

effects of automobile battery wastes on physicochemical properties

African Journals Online (AJOL)

PROF. BARTH EKWEME

2015-09-28

Sep 28, 2015 ... wastes were found to be significant sources of Cadmium and Chromium, as none of both was detected in the control ... of battery waste contaminated soil in spite of extensive ..... requires remediation to minimize soil pollution.

Innovative technologies for managing oil field waste

International Nuclear Information System (INIS)

Veil, J.A.

2003-01-01

Each year, the oil industry generates millions of barrels of wastes that need to be properly managed. For many years, most oil field wastes were disposed of at a significant cost. However, over the past decade, the industry has developed many processes and technologies to minimize the generation of wastes and to more safely and economically dispose of the waste that is generated. Many companies follow a three-tiered waste management approach. First, companies try to minimize waste generation when possible. Next, they try to find ways to reuse or recycle the wastes that are generated. Finally, the wastes that cannot be reused or recycled must be disposed of. Argonne National Laboratory (Argonne) has evaluated the feasibility of various oil field waste management technologies for the U.S. Department of Energy. This paper describes four of the technologies Argonne has reviewed. In the area of waste minimization, the industry has developed synthetic-based drilling muds (SBMs) that have the desired drilling properties of oil-based muds without the accompanying adverse environmental impacts. Use of SBMs avoids significant air pollution from work boats hauling offshore cuttings to shore for disposal and provides more efficient drilling than can be achieved with water-based muds. Downhole oil/water separators have been developed to separate produced water from oil at the bottom of wells. The produced water is directly injected to an underground formation without ever being lifted to the surface, thereby avoiding potential for groundwater or soil contamination. In the area of reuse/recycle, Argonne has worked with Southeastern Louisiana University and industry to develop a process to use treated drill cuttings to restore wetlands in coastal Louisiana. Finally, in an example of treatment and disposal, Argonne has conducted a series of four baseline studies to characterize the use of salt caverns for safe and economic disposal of oil field wastes.

Hazardous Waste Minimization Assessment: Fort Campbell, Kentucky

Science.gov (United States)

1991-03-01

gal/h -- $8,250 (solvents: chlorinated and $8,600 fluorinated ) 114 Table 39 Aqueous Waste Volume Reduction Equipment Suppliers* Supplier Model Capacity...heavy chloride/hydrochloric acid metal solutions (chromium), nitric acid (zinc, magnesium) Printing (Ink) pigments, dyes, varnish , titanium oxide, iron...lacquers, epoxy. aLkyds. acrylics) :inshing Varnish . shellac, lacquer 13001 Waste flammable liquid. NOS Flammable liquid UN1993 Preserving Creosote

LEAN HEALTHCARE SUPPLY CHAIN MANAGEMENT: MINIMIZING WASTE AND COSTS

Directory of Open Access Journals (Sweden)

Catia M L Machado

2014-12-01

Full Text Available The purpose of this research is to investigate the management models applied in the supply chain providing services in healthcare organizations, considering the lenses of lean. The aim of this is to develop a model of supply chain management focusing on the identification and minimization of waste, assisting in decision making and contributing to the quality of services and as a consequence the reduction of the costs involved in healthcare supply chain. The philosophies of continuous improvement and lean techniques have a role to play in helping healthcare to provide quality service and support to reduce costs in the current budget constraints. In the supply chain of hospitals the financial costs can be around 40% of its budget (MASOUMI et al. 2012; SOUZA et al., 2013. This article sheds light on the improvement in decision making and the effect of reducing costs in the healthcare supply chain. In this sense, the research intend to expand knowledge related to supply chain management in the area of ​​provision of healthcare services through the use of the philosophy of continuous improvement and lean principles, helping healthcare to provide quality service within their current budget constraints.

Managing Waste Throughout Lean-Green Perspective

Directory of Open Access Journals (Sweden)

Lamyaa Mohammed Dawood

2017-11-01

Full Text Available Managing waste has been known as a crucial need as it may reduce resource consumption, rigid regulations regarded to the environment and occupational health and safety. Lean and green management are two approaches of management that validate waste. Since performance measures are crucial to improve waste management as its  goals of  to promote the performance of organizations .In this research four primary KPIs have been employed that are significant to lean-green management; operational, environmental, economic and social performance factors, subdivided further into sixteen as (Value stream mapping, life cycle assessment,---etc. Also in this research   determination and ranking of these performance measures and their influence on waste minimization is conducted. Interpretive Structural Modeling (ISM methodology is applied to the classification of Key Performance Indicators (KPIs according to the priority of their importance and the correlation between them and their impact to waste minimization. Cronbach’s Alpha coefficient is employed  to assess the reliability of performance measures to minimize waste, and increase customer  satisfaction.  Results showed that Al-Kufa Cement plant has bad overall performance toward lean green waste management perspective. The highest individual score is for operational performance (6.6 rated as medium. But  the lowest individual score is for economic performance [very bad (2.0].   

Waste processing plant eco-auditing system for minimization of environmental risk: European Communities regulatory proposal

International Nuclear Information System (INIS)

Brunetti, N.

1993-01-01

This paper delineates a system of process control and monitoring checks to be applied to municipal-industrial waste processing and disposal plants to ensure their energy efficient, environmentally safe and reliable operation. In line with European Communities environmental protection strategies, this eco-auditing system requires the preparation of environmental impacts statements on a regular basis during plant operation, as well as, prior to plant start-up. Continuous plant environmental compatibility evaluations are to ascertain: material and energy inputs and outputs; the composition and amounts of exhaust gases released into the atmosphere and the integrity of treatment liquids; control and monitoring instrumentation reliability. The implementation of the auditing system is to be carried out under the supervision of authorized auditing personnel. Waste processing and disposal plants are to make maximum use of energy and materials recovery processes so as to minimize energy consumption and risk to the environment

Knowledge-based and model-based hybrid methodology for comprehensive waste minimization in electroplating plants

Science.gov (United States)

Luo, Keqin

1999-11-01

The electroplating industry of over 10,000 planting plants nationwide is one of the major waste generators in the industry. Large quantities of wastewater, spent solvents, spent process solutions, and sludge are the major wastes generated daily in plants, which costs the industry tremendously for waste treatment and disposal and hinders the further development of the industry. It becomes, therefore, an urgent need for the industry to identify technically most effective and economically most attractive methodologies and technologies to minimize the waste, while the production competitiveness can be still maintained. This dissertation aims at developing a novel WM methodology using artificial intelligence, fuzzy logic, and fundamental knowledge in chemical engineering, and an intelligent decision support tool. The WM methodology consists of two parts: the heuristic knowledge-based qualitative WM decision analysis and support methodology and fundamental knowledge-based quantitative process analysis methodology for waste reduction. In the former, a large number of WM strategies are represented as fuzzy rules. This becomes the main part of the knowledge base in the decision support tool, WMEP-Advisor. In the latter, various first-principles-based process dynamic models are developed. These models can characterize all three major types of operations in an electroplating plant, i.e., cleaning, rinsing, and plating. This development allows us to perform a thorough process analysis on bath efficiency, chemical consumption, wastewater generation, sludge generation, etc. Additional models are developed for quantifying drag-out and evaporation that are critical for waste reduction. The models are validated through numerous industrial experiments in a typical plating line of an industrial partner. The unique contribution of this research is that it is the first time for the electroplating industry to (i) use systematically available WM strategies, (ii) know quantitatively and

Hanford Site annual waste reduction report

International Nuclear Information System (INIS)

Nichols, D.H.

1992-03-01

The US Department of Energy (DOE), Richland Field Office (RL) has developed and implemented a Hanford Site Waste Minimization and Pollution Prevention Awareness Plan that provides overall guidance and direction on waste minimization and pollution prevention awareness to the four contractors who manage and operate the Hanford Site for the RL. Waste reduction at the RL will be accomplished by following a hierarchy of environmental protection practices. First, waste generation will be eliminated or minimized through source reduction. Second, potential waste materials that cannot be eliminated or minimized will be recycled (i.e., used, reused, or reclaimed). Third, all waste that is nevertheless generated will be treated to reduce volume, toxicity, or mobility before storage or disposal. The scope of this waste reduction program will include nonhazardous, hazardous, radioactive mixed, and radioactive wastes

Minimum Additive Waste Stabilization (MAWS)

International Nuclear Information System (INIS)

1994-02-01

In the Minimum Additive Waste Stabilization(MAWS) concept, actual waste streams are utilized as additive resources for vitrification, which may contain the basic components (glass formers and fluxes) for making a suitable glass or glassy slag. If too much glass former is present, then the melt viscosity or temperature will be too high for processing; while if there is too much flux, then the durability may suffer. Therefore, there are optimum combinations of these two important classes of constituents depending on the criteria required. The challenge is to combine these resources in such a way that minimizes the use of non-waste additives yet yields a processable and durable final waste form for disposal. The benefit to this approach is that the volume of the final waste form is minimized (waste loading maximized) since little or no additives are used and vitrification itself results in volume reduction through evaporation of water, combustion of organics, and compaction of the solids into a non-porous glass. This implies a significant reduction in disposal costs due to volume reduction alone, and minimizes future risks/costs due to the long term durability and leach resistance of glass. This is accomplished by using integrated systems that are both cost-effective and produce an environmentally sound waste form for disposal. individual component technologies may include: vitrification; thermal destruction; soil washing; gas scrubbing/filtration; and, ion-exchange wastewater treatment. The particular combination of technologies will depend on the waste streams to be treated. At the heart of MAWS is vitrification technology, which incorporates all primary and secondary waste streams into a final, long-term, stabilized glass wasteform. The integrated technology approach, and view of waste streams as resources, is innovative yet practical to cost effectively treat a broad range of DOE mixed and low-level wastes

Plasma filtering techniques for nuclear waste remediation.

Science.gov (United States)

Gueroult, Renaud; Hobbs, David T; Fisch, Nathaniel J

2015-10-30

Nuclear waste cleanup is challenged by the handling of feed stocks that are both unknown and complex. Plasma filtering, operating on dissociated elements, offers advantages over chemical methods in processing such wastes. The costs incurred by plasma mass filtering for nuclear waste pretreatment, before ultimate disposal, are similar to those for chemical pretreatment. However, significant savings might be achieved in minimizing the waste mass. This advantage may be realized over a large range of chemical waste compositions, thereby addressing the heterogeneity of legacy nuclear waste. Copyright © 2015 Elsevier B.V. All rights reserved.

Trim waste minimization at the Pinellas Plant

International Nuclear Information System (INIS)

DeLaneuville, D.

1992-01-01

Bacteria counts and several methods of slowing bacterial growth in machine trim coolant are suggested to reduce the frequency of coolant replacement without risking employee health or the longevity of the product or machinery. On-site treatment and disposal of waste trim are recommended to further reduce waste volume. This paper discusses the benefits of these efforts, including projected cost savings based on partial implementation at the Department of Energy's Pinellas Plant

The use of absorption spectroscopy of plutonium to minimize waste streams

International Nuclear Information System (INIS)

Vaughn, R.B.; Berg, J.; Cisneros, M.

1997-01-01

Through the use of absorption spectroscopy we are better able to understand the chemical reactions of plutonium and other actinide elements in solution. In many cases such an understanding can minimize the generation of waste streams by suggesting more optimal chemical conditions for separating these radioactive elements from their host matrix. Many processes are developed using an empirical approach with little understanding of what is actually taking place. One such example is the anion exchange process for Plutonium purification. Various resins have been tested in various solutions and workable outcomes have been produced. However, absorption spectroscopy provides an understanding of why ion exchange works and can determine which compounds complex best with actinides in order to obtain a more efficient and effective separations process. This presentation will touch on the chemistry involved, the spectroscopic instrumentation, and the environmental impacts. Primarily the talk will focus on the chemical technicians involvement in the day to day research, the obstacles encountered, and the environment in which this research was conducted

Security of Radioactive Waste

International Nuclear Information System (INIS)

Goldammer, W.

2003-01-01

Measures to achieve radioactive waste security are discussed. Categorization of waste in order to implement adequate and consistent security measures based on potential consequences is made. The measures include appropriate treatment/storage/disposal of waste to minimize the potential and consequences of malicious acts; management of waste only within an authorised, regulated, legal framework; management of the security of personnel and information; measures to minimize the acquisition of radioactive waste by those with malicious intent. The specific measures are: deter unauthorized access to the waste; detect any such attempt or any loss or theft of waste; delay unauthorized access; provide timely response to counter any attempt to gain unauthorised access; measures to minimize acts of sabotage; efforts to recover any lost or stolen waste; mitigation and emergency plans in case of release of radioactivity. An approach to develop guidance, starting with the categorisation of sources and identification of dangerous sources, is presented. Dosimetric criteria for internal and external irradiation are set. Different exposure scenarios are considered. Waste categories and security categories based on the IAEA INFCIRC/225/Rev.4 are presented

Proceedings of the US Department of Energy Office of Environmental Restoration and Waste Management waste reduction workshop 4

International Nuclear Information System (INIS)

1990-03-01

The fourth of a series of waste minimization/reduction workshops was held at the Sheridan Grand Hotel in Tampa, Florida, on February 6--7, 1990. The workshops are held under the auspices of the Department of Energy's (DOE's) Office of Environmental Restoration and Waste Management. This workshop provided a forum for waste minimization/reduction planning, including waste minimization assessments. The workshops assist DOE waste-generating sites in implementing waste minimization/reduction programs, plans, and activities, thus providing for optimal waste reduction within the DOE complex. All wastes are considered within this discipline: liquid, solid, and airborne, within the categories of high-level, transuranic (TRU), low-level (LLW), hazardous, and mixed. Topics of discussion within workshops encompassed a wide range of subjects. Subjects included any method or technical activity from waste generation to disposal, such as process design or improvement, substitution of materials, waste segregation and recycling/reuse, waste treatment and processing, and administrative controls (procurement and waste awareness training). Consideration was also given to activities for remedial action and for decontamination and disposal. 1 tab

Minimization of waste volumes by means of pin-pointed decontamination during decommissioning measures. Final report

International Nuclear Information System (INIS)

Henschel, K.; Jacobs, W.; Kanitz, L.; Schildbach, T.

1992-06-01

This semi-automated equipment is able to remove surface building contamination as well as take radioactive measurements. This equipment is newly developed. The goal of the equipment is to improve the identification of areas of contamination and the compounding decontamination of epoxy layer building construction material by using commercially available components minimizing the waste volume. A system design for decommissioning of building surfaces was developed, selected components were tested and their function certified. With this systems concept the decontamination of fixed epoxy layers up to 20 m in height is possible. Operational data for the system are available. (orig.) [de

Feasibility Studies on Pipeline Disposal of Concentrated Copper Tailings Slurry for Waste Minimization

Science.gov (United States)

Senapati, Pradipta Kumar; Mishra, Barada Kanta

2017-06-01

The conventional lean phase copper tailings slurry disposal systems create pollution all around the disposal area through seepage and flooding of waste slurry water. In order to reduce water consumption and minimize pollution, the pipeline disposal of these waste slurries at high solids concentrations may be considered as a viable option. The paper presents the rheological and pipeline flow characteristics of copper tailings samples in the solids concentration range of 65-72 % by weight. The tailings slurry indicated non-Newtonian behaviour at these solids concentrations and the rheological data were best fitted by Bingham plastic model. The influence of solids concentration on yield stress and plastic viscosity for the copper tailings samples were discussed. Using a high concentration test loop, pipeline experiments were conducted in a 50 mm nominal bore (NB) pipe by varying the pipe flow velocity from 1.5 to 3.5 m/s. A non-Newtonian Bingham plastic pressure drop model predicted the experimental data reasonably well for the concentrated tailings slurry. The pressure drop model was used for higher size pipes and the operating conditions for pipeline disposal of concentrated copper tailings slurry in a 200 mm NB pipe with respect to specific power consumption were discussed.

Waste minimization and pollution prevention in D ampersand D operations at the Argonne National Laboratory-East site

International Nuclear Information System (INIS)

Boing, L.E.; Coffey, M.J.; Ditch, R.W.; Fellhauer, C.R.; Rose, R.W.

1996-01-01

Argonne National Laboratory (ANL) is implementing waste minimization and pollution prevention activities into its conduct of decontamination and decommissioning (D ampersand D) projects. Many of these activities are rather straight forward and simple approaches, yet they are often overlooked and not implemented as often as they should or could be. Specific activities involving recycling and reuse of materials and structures, which have proven useful in lowering decommissioning and disposal costs on D ampersand D projects at ANL are presented

Waste management/waste certification plan for the Oak Ridge National Laboratory Environmental Restoration Program

International Nuclear Information System (INIS)

Clark, C. Jr.; Hunt-Davenport, L.D.; Cofer, G.H.

1995-03-01

This Waste Management/Waste Certification (C) Plan, written for the Environmental Restoration (ER) Program at Oak Ridge National Laboratory (ORNL), outlines the criteria and methodologies to be used in the management of waste generated during ORNL ER field activities. Other agreed upon methods may be used in the management of waste with consultation with ER and Waste Management Organization. The intent of this plan is to provide information for the minimization, handling, and disposal of waste generated by ER activities. This plan contains provisions for the safe and effective management of waste consistent with the U.S. Environmental Protection Agency's (EPA's) guidance. Components of this plan have been designed to protect the environment and the health and safety of workers and the public. It, therefore, stresses that investigation derived waste (IDW) and other waste be managed to ensure that (1) all efforts be made to minimize the amount of waste generated; (2) costs associated with sampling storage, analysis, transportation, and disposal are minimized; (3) the potential for public and worker exposure is not increased; and (4) additional contaminated areas are not created

Analysis of the application of decontamination technologies to radioactive metal waste minimization using expert systems

Energy Technology Data Exchange (ETDEWEB)

Bayrakal, Suna [Iowa State Univ., Ames, IA (United States)

1993-09-30

Radioactive metal waste makes up a significant portion of the waste currently being sent for disposal. Recovery of this metal as a valuable resource is possible through the use of decontamination technologies. Through the development and use of expert systems a comparison can be made of laser decontamination, a technology currently under development at Ames Laboratory, with currently available decontamination technologies for applicability to the types of metal waste being generated and the effectiveness of these versus simply disposing of the waste. These technologies can be technically and economically evaluated by the use of expert systems techniques to provide a waste management decision making tool that generates, given an identified metal waste, waste management recommendations. The user enters waste characteristic information as input and the system then recommends decontamination technologies, determines residual contamination levels and possible waste management strategies, carries out a cost analysis and then ranks, according to cost, the possibilities for management of the waste. The expert system was developed using information from literature and personnel experienced in the use of decontamination technologies and requires validation by human experts and assignment of confidence factors to the knowledge represented within.

Analysis of the application of decontamination technologies to radioactive metal waste minimization using expert systems

International Nuclear Information System (INIS)

Bayrakal, S.

1993-01-01

Radioactive metal waste makes up a significant portion of the waste currently being sent for disposal. Recovery of this metal as a valuable resource is possible through the use of decontamination technologies. Through the development and use of expert systems a comparison can be made of laser decontamination, a technology currently under development at Ames Laboratory, with currently available decontamination technologies for applicability to the types of metal waste being generated and the effectiveness of these versus simply disposing of the waste. These technologies can be technically and economically evaluated by the use of expert systems techniques to provide a waste management decision making tool that generates, given an identified metal waste, waste management recommendations. The user enters waste characteristic information as input and the system then recommends decontamination technologies, determines residual contamination levels and possible waste management strategies, carries out a cost analysis and then ranks, according to cost, the possibilities for management of the waste. The expert system was developed using information from literature and personnel experienced in the use of decontamination technologies and requires validation by human experts and assignment of confidence factors to the knowledge represented within

Waste management

International Nuclear Information System (INIS)

Chmielewska, E.

2010-01-01

In this chapter formation of wastes and basic concepts of non-radioactive waste management are explained. This chapter consists of the following parts: People in Peril; Self-regulation of nature as a guide for minimizing and recycling waste; The current waste management situation in the Slovak Republic; Categorization and determination of the type of waste in legislative of Slovakia; Strategic directions waste management in the Slovak Republic.

Does industrial waste taxation contribute to reduction of landfilled waste? Dynamic panel analysis considering industrial waste category in Japan.

Science.gov (United States)

Sasao, Toshiaki

2014-11-01

Waste taxes, such as landfill and incineration taxes, have emerged as a popular option in developed countries to promote the 3Rs (reduce, reuse, and recycle). However, few studies have examined the effectiveness of waste taxes. In addition, quite a few studies have considered both dynamic relationships among dependent variables and unobserved individual heterogeneity among the jurisdictions. If dependent variables are persistent, omitted variables cause a bias, or common characteristics exist across the jurisdictions that have introduced waste taxes, the standard fixed effects model may lead to biased estimation results and misunderstood causal relationships. In addition, most existing studies have examined waste in terms of total amounts rather than by categories. Even if significant reductions in total waste amounts are not observed, some reduction within each category may, nevertheless, become evident. Therefore, this study analyzes the effects of industrial waste taxation on quantities of waste in landfill in Japan by applying the bias-corrected least-squares dummy variable (LSDVC) estimators; the general method of moments (difference GMM); and the system GMM. In addition, the study investigates effect differences attributable to industrial waste categories and taxation types. This paper shows that industrial waste taxes in Japan have minimal, significant effects on the reduction of final disposal amounts thus far, considering dynamic relationships and waste categories. Copyright © 2014 Elsevier Ltd. All rights reserved.

The Future: Innovative Technologies for Radioactive Waste Processing and Disposal

International Nuclear Information System (INIS)

Bychkov, Alexander V.

2014-01-01

Safe, proliferation resistant and economically efficient nuclear fuel cycles that minimize waste generation and environmental impacts are key to sustainable nuclear energy. Innovative approaches and technologies could significantly reduce the radiotoxicity, or the hazard posed by radioactive substances to humans, as well as the waste generated. Decreasing the waste volume, the heat load and the duration that the waste needs to be isolated from the biosphere will greatly simplify waste disposal concepts

Application of molten salt oxidation for the minimization and recovery of plutonium-238 contaminated wastes

International Nuclear Information System (INIS)

Wishau, R.; Ramsey, K.B.; Montoya, A.

1998-01-01

This paper presents the technical and economic feasibility of molten salt oxidation technology as a volume reduction and recovery process for 238 Pu contaminated waste. Combustible low-level waste material contaminated with 238 Pu residue is destroyed by oxidation in a 900 C molten salt reaction vessel. The combustible waste is destroyed creating carbon dioxide and steam and a small amount of ash and insoluble 2328 Pu in the spent salt. The valuable 238 Pu is recycled using aqueous recovery techniques. Experimental test results for this technology indicate a plutonium recovery efficiency of 99%. Molten salt oxidation stabilizes the waste converting it to a non-combustible waste. Thus installation and use of molten salt oxidation technology will substantially reduce the volume of 238 Pu contaminated waste. Cost-effectiveness evaluations of molten salt oxidation indicate a significant cost savings when compared to the present plans to package, or re-package, certify and transport these wastes to the Waste Isolation Pilot Plant for permanent disposal. Clear and distinct cost advantages exist for MSO when the monetary value of the recovered 238 Pu is considered

Surrogate formulations for thermal treatment of low-level mixed waste, Part II: Selected mixed waste treatment project waste streams

Energy Technology Data Exchange (ETDEWEB)

Bostick, W.D.; Hoffmann, D.P.; Chiang, J.M.; Hermes, W.H.; Gibson, L.V. Jr.; Richmond, A.A. [Martin Marietta Energy Systems, Inc., Oak Ridge, TN (United States); Mayberry, J. [Science Applications International Corp., Idaho Falls, ID (United States); Frazier, G. [Univ. of Tennessee, Knoxville, TN (United States)

1994-01-01

This report summarizes the formulation of surrogate waste packages, representing the major bulk constituent compositions for 12 waste stream classifications selected by the US DOE Mixed Waste Treatment Program. These waste groupings include: neutral aqueous wastes; aqueous halogenated organic liquids; ash; high organic content sludges; adsorbed aqueous and organic liquids; cement sludges, ashes, and solids; chloride; sulfate, and nitrate salts; organic matrix solids; heterogeneous debris; bulk combustibles; lab packs; and lead shapes. Insofar as possible, formulation of surrogate waste packages are referenced to authentic wastes in inventory within the DOE; however, the surrogate waste packages are intended to represent generic treatability group compositions. The intent is to specify a nonradiological synthetic mixture, with a minimal number of readily available components, that can be used to represent the significant challenges anticipated for treatment of the specified waste class. Performance testing and evaluation with use of a consistent series of surrogate wastes will provide a means for the initial assessment (and intercomparability) of candidate treatment technology applicability and performance. Originally the surrogate wastes were intended for use with emerging thermal treatment systems, but use may be extended to select nonthermal systems as well.

Surrogate formulations for thermal treatment of low-level mixed waste, Part II: Selected mixed waste treatment project waste streams

International Nuclear Information System (INIS)

Bostick, W.D.; Hoffmann, D.P.; Chiang, J.M.; Hermes, W.H.; Gibson, L.V. Jr.; Richmond, A.A.; Mayberry, J.; Frazier, G.

1994-01-01

This report summarizes the formulation of surrogate waste packages, representing the major bulk constituent compositions for 12 waste stream classifications selected by the US DOE Mixed Waste Treatment Program. These waste groupings include: neutral aqueous wastes; aqueous halogenated organic liquids; ash; high organic content sludges; adsorbed aqueous and organic liquids; cement sludges, ashes, and solids; chloride; sulfate, and nitrate salts; organic matrix solids; heterogeneous debris; bulk combustibles; lab packs; and lead shapes. Insofar as possible, formulation of surrogate waste packages are referenced to authentic wastes in inventory within the DOE; however, the surrogate waste packages are intended to represent generic treatability group compositions. The intent is to specify a nonradiological synthetic mixture, with a minimal number of readily available components, that can be used to represent the significant challenges anticipated for treatment of the specified waste class. Performance testing and evaluation with use of a consistent series of surrogate wastes will provide a means for the initial assessment (and intercomparability) of candidate treatment technology applicability and performance. Originally the surrogate wastes were intended for use with emerging thermal treatment systems, but use may be extended to select nonthermal systems as well

Waste Reduction plan for Oak Ridge National Laboratory

Energy Technology Data Exchange (ETDEWEB)

1991-12-01

Oak Ridge National Laboratory (ORNL) is a multipurpose research and development (R&D) facility owned and operated by the Department of Energy (DOE) and managed under subcontract by Martin Marietta Energy Systems (Energy Systems), Inc. ORNL R&D activities generate numerous small waste streams. In the hazardous waste category alone, over 300 streams of a diverse nature exist. Generation avoidance, reduction or recycling of wastes is an important goal in maintaining efficiency of ORNL R&D activities and protection of workers, the public, and the environment. Waste minimization is defined as any action that minimizes or eliminates the volume or toxicity of waste by avoiding its generation or recycling. This is accomplished by material substitution and inventory management, process modification, or recycling wastes for reuse. Waste reduction is defined as waste minimization plus treatment which results in volume or toxicity reduction. The ORNL Waste Reduction Program will include both waste minimization and waste reduction activities.

Waste Reduction plan for Oak Ridge National Laboratory

Energy Technology Data Exchange (ETDEWEB)

1991-12-01

Oak Ridge National Laboratory (ORNL) is a multipurpose research and development (R D) facility owned and operated by the Department of Energy (DOE) and managed under subcontract by Martin Marietta Energy Systems (Energy Systems), Inc. ORNL R D activities generate numerous small waste streams. In the hazardous waste category alone, over 300 streams of a diverse nature exist. Generation avoidance, reduction or recycling of wastes is an important goal in maintaining efficiency of ORNL R D activities and protection of workers, the public, and the environment. Waste minimization is defined as any action that minimizes or eliminates the volume or toxicity of waste by avoiding its generation or recycling. This is accomplished by material substitution and inventory management, process modification, or recycling wastes for reuse. Waste reduction is defined as waste minimization plus treatment which results in volume or toxicity reduction. The ORNL Waste Reduction Program will include both waste minimization and waste reduction activities.

Significance of radiation effects in solid radioactive waste

International Nuclear Information System (INIS)

Permar, P.H.; McDonell, W.R.

1980-01-01

Proposed NRC criteria for disposal of high-level nuclear waste require development of waste packages to contain radionuclide for at least 1000 years, and design of repositories to prevent radionuclide release at an annual rate greater than 1 part in 100,000 of the total activity. The high-level wastes that are now temporarily stored as aqueous salts, sludges, and calcines must be converted to high-integrity solid forms that resist deterioration from radiation and other effects of long-term storage. Spent fuel may be encapsulated for similar long-term storage. Candidate waste forms beside the spent fuel elements themselves, include borosilicate and related glasses, mineral-like crystalline ceramics, concrete formulations, and metal-matrix glass or ceramic composites. these waste forms will sustain damage produced by beta-gamma radiation up to 10 12 rads, by alpha radiation up to 10 19 particles/g, by internal helium generation greater than about 0.1 atom percent, and by the atom transmutations accompanying radioactive decay. Current data indicate that under these conditions the glass forms suffer only minor volume changes, stored energy deposition, and leachability effects. The crystalline ceramics appear susceptible to the potentially more severe alterations accompanying metamictization and natural analogs of candidate materials are being examined to establish their suitability as waste forms. Helium concentrations in the waste forms are generally below thresholds for severe damage in either glass or crystalline ceramics at low temperatures, but microstructural effects are not well characterized. Transmutation effects remain to be established

Recycling - Danish Waste Management Strategy

DEFF Research Database (Denmark)

Romann, Anne Funch; Thøgersen, John; Husmer, Lis

The report challanges recycling as the only waste handling strategy. The tonnes of recycled materials should not be the only goal - it is essential to minimize the waste production and focus on eliminating hazardous materials.......The report challanges recycling as the only waste handling strategy. The tonnes of recycled materials should not be the only goal - it is essential to minimize the waste production and focus on eliminating hazardous materials....

Waste minimization: A team approach at McGuire nuclear

International Nuclear Information System (INIS)

Poteat, E.L.

1995-01-01

The production of radioactive waste and its subsequent disposal is a costly proposition. Burial of low-level waste (LLW), if available at all, is expensive and getting more so. The availability of disposal options is often subject to the whims and vagaries of political forces that cannot be predicted, let alone controlled in any way by the members of the nuclear community. On-site storage is a limited and, quite often, an extremely difficult process to put into place. After LLW has been generated, various volume reduction techniques are available, but these can vary widely in cost and effectiveness. If and when new disposal sites are available, the waste acceptance criteria may be such that some or all of the volume reduction processes will not produce an acceptable final waste form. Consequently, the best thing to do is probably deceptively simple: Do not generate the waste in the first place. This is the philosophy that McGuire nuclear station operates under, and this paper discusses the team approach that has been developed to support this idea

Waste reduction plan for The Oak Ridge National Laboratory

Energy Technology Data Exchange (ETDEWEB)

Schultz, R.M.

1990-04-01

The Oak Ridge National Laboratory (ORNL) is a multipurpose Research and Development (R D) facility. These R D activities generate numerous small waste streams. Waste minimization is defined as any action that minimizes the volume or toxicity of waste by avoiding its generation or recycling. This is accomplished by material substitution, changes to processes, or recycling wastes for reuse. Waste reduction is defined as waste minimization plus treatment which results in volume or toxicity reduction. The ORNL Waste Reduction Program will include both waste minimization and waste reduction efforts. Federal regulations, DOE policies and guidelines, increased costs and liabilities associated with the management of wastes, limited disposal options and facility capacities, and public consciousness have been motivating factors for implementing comprehensive waste reduction programs. DOE Order 5820.2A, Section 3.c.2.4 requires DOE facilities to establish an auditable waste reduction program for all LLW generators. In addition, it further states that any new facilities, or changes to existing facilities, incorporate waste minimization into design considerations. A more recent DOE Order, 3400.1, Section 4.b, requires the preparation of a waste reduction program plan which must be reviewed annually and updated every three years. Implementation of a waste minimization program for hazardous and radioactive mixed wastes is sited in DOE Order 5400.3, Section 7.d.5. This document has been prepared to address these requirements. 6 refs., 1 fig., 2 tabs.

Waste reduction plan for The Oak Ridge National Laboratory

International Nuclear Information System (INIS)

Schultz, R.M.

1990-04-01

The Oak Ridge National Laboratory (ORNL) is a multipurpose Research and Development (R ampersand D) facility. These R ampersand D activities generate numerous small waste streams. Waste minimization is defined as any action that minimizes the volume or toxicity of waste by avoiding its generation or recycling. This is accomplished by material substitution, changes to processes, or recycling wastes for reuse. Waste reduction is defined as waste minimization plus treatment which results in volume or toxicity reduction. The ORNL Waste Reduction Program will include both waste minimization and waste reduction efforts. Federal regulations, DOE policies and guidelines, increased costs and liabilities associated with the management of wastes, limited disposal options and facility capacities, and public consciousness have been motivating factors for implementing comprehensive waste reduction programs. DOE Order 5820.2A, Section 3.c.2.4 requires DOE facilities to establish an auditable waste reduction program for all LLW generators. In addition, it further states that any new facilities, or changes to existing facilities, incorporate waste minimization into design considerations. A more recent DOE Order, 3400.1, Section 4.b, requires the preparation of a waste reduction program plan which must be reviewed annually and updated every three years. Implementation of a waste minimization program for hazardous and radioactive mixed wastes is sited in DOE Order 5400.3, Section 7.d.5. This document has been prepared to address these requirements. 6 refs., 1 fig., 2 tabs

Waste minimization and the goal of an environmentally benign plutonium processing facility: A strategic plan

International Nuclear Information System (INIS)

Pillay, K.K.S.

1994-02-01

To maintain capabilities in nuclear weapons technologies, the Department of Energy (DOE) has to maintain a plutonium processing facility that meets all the current and emerging standards of environmental regulations. A strategic goal to transform the Plutonium Processing Facility at Los Alamos into an environmentally benign operation is identified. A variety of technologies and systems necessary to meet this goal are identified. Two initiatives now in early stages of implementation are described in some detail. A highly motivated and trained work force and a systems approach to waste minimization and pollution prevention are necessary to maintain technical capabilities, to comply with regulations, and to meet the strategic goal

Industrial waste management - a case study at Attock oil refinery Ltd., Rawalpindi

International Nuclear Information System (INIS)

Ramay, M.I.; Hussain, S.; Tanveer, A.; Jabeen, Z.; Ehsann, S.

2009-01-01

As far as waste is concerned, industry has a two fold position: on the one hand industry produces waste during the production processes and on the other hand most of the industrial products become waste after being used. From environment perspective waste management and minimization at the source has become important issue all over the world. Waste minimization leading to cleaner production is the process and the policy of reducing the amount of waste produced by Industry at the source and remaining should be managed.The core objective of this research paper is to examine the impact of waste minimization, waste management and the planning of effective waste utilization that increases organizations profitability and green image. The case study will present the Recycle, Reuse, Reduce strategy that waste management is not only necessary to keep the environment healthy but it also brings the financial savings to the organization. It is obvious that there is significant relationship between waste management and profitability. Attock Refinery Limited (ARL) has done significant work in the field of industrial waste management. The stratified sampling has also used during a survey to gather primary data i.e. congregated by administering questionnaires to employees of different departments that shows positive attitude towards waste minimization and management. The interventions regarding industrial waste management are in full practice at ARL to meet the National Environmental Quality Standards. In 1993, prominent step has been taken to address the environmental issues and waste management. After carrying out the detailed survey of effluent waste water system during 1995-1996, Effluent Treatment Plants were installed to meet the NEQS. Keeping the continuity of efforts 'Zero Discharge' of effluent waste from the refinery was targeted. This project is recycling the waste water resulting environment conservation and saving money that was being spent for water pumping from

WasteWise Resource Management: Innovative Solid Waste Contracting Methods

Science.gov (United States)

Resource management is an innovative contractual partnership between a waste-generating organization and a qualified contractor that changes the nature of current disposal services to support waste minimization and recycling.

Use of plutonium and minor actinides as fuel in high temperature pebble bed reactors for waste minimization

International Nuclear Information System (INIS)

Meier, Astrid; Bernnat, Wolfgang; Lohnert, Guenther

2009-01-01

Energy production by nuclear fission gives rise to longlived radionuclides, such as plutonium and americium. The ''PuMA'' (Plutonium and Minor Actinides Waste Management) research project within the 6th Framework Program of the European Union serves to minimize waste arisings and transmute plutonium and minor actinides from spent LWR fuel elements by means of modular high-temperature reactors (HTR). Coating the fuel, which consists of kernels approx. 250 μm in radius and surrounded by graphite as the moderator material, allows very high operating and accident temperatures and very high burnups. One point examined is whether the inherent safety characteristics known for uranium oxide also exist for (PuO 2 + MAO 2 ) fuel. On the basis of a reference reactor similar to the South African PBMR-400, various loading strategies at maximum burnup are considered with a view to the inherent safety of the HTR. (orig.)

Characterization, minimization and disposal of radioactive, hazardous, and mixed wastes during cleanup and rransition of the Tritium Research Laboratory (TRL) at Sandia National Laboratories/California (SNL/CA)

International Nuclear Information System (INIS)

Garcia, T.B.; Gorman, T.P.

1996-12-01

This document provides an outline of waste handling practices used during the Sandia National Laboratory/California (SNL/CA), Tritium Research Laboratory (TRL) Cleanup and Transition project. Here we provide background information concerning the history of the TRL and the types of operations that generated the waste. Listed are applicable SNL/CA site-wide and TRL local waste handling related procedures. We describe personnel training practices and outline methods of handling and disposal of compactible and non-compactible low level waste, solidified waste water, hazardous wastes and mixed wastes. Waste minimization, reapplication and recycling practices are discussed. Finally, we provide a description of the process followed to remove the highly contaminated decontamination systems. This document is intended as both a historical record and as a reference to other facilities who may be involved in similar work

Waste minimization through microexperimentation: Barriers to implementation

International Nuclear Information System (INIS)

Gatrone, R.C.

1994-01-01

In the past, synthesis of ligands and extractants for concentrating radwaste, often resulted in generating large amounts of hazardous wastes. Microexperimentation means handling amounts of organics on the scale of millimoles (10 -3 ) to micromoles (10 -6 ). More reliable analytical techniques allow one to obtain data nondestructively on the structure of a molecule on just a few milligrams of material. Obstacles to use of microscale techniques in laboratories include requirement of new, expensive equipment, and resistance of laboratory personnel to new techniques. It is emphasized that in the Argonne laboratory, of the 500 g of an extractant that was required in 1985, nearly 90% was ultimately discarded as waste after 5 years. DOE agreements and other Federal regulations require this be changed

Waste minimization at a plutonium processing facility

International Nuclear Information System (INIS)

Pillay, K.K.S.

1995-01-01

As part of Los Alamos National Laboratory's (LANL) mission to reduce the nuclear danger throughout the world, the plutonium processing facility at LANL maintains expertise and skills in nuclear weapons technologies as well as leadership in all peaceful applications of plutonium technologies, including fuel fabrication for terrestrial and space reactors and heat sources and thermoelectric generators for space missions. Another near-term challenge resulted from two safety assessments performed by the Defense Nuclear Facilities Safety Board and the U.S. Department of Energy during the past two years. These assessments have necessitated the processing and stabilization of plutonium contained in tons of residues so that they can be stored safely for an indefinite period. This report describes waste streams and approaches to waste reduction of plutonium management

Impact assessment of waste management options in Singapore.

Science.gov (United States)

Tan, Reginald B H; Khoo, Hsien H

2006-03-01

This paper describes the application of life cycle assessment for evaluating various waste management options in Singapore, a small-island city state. The impact assessment method by SimaPro is carried out for comparing the potential environmental impacts of waste treatment options including landfilling, incineration, recycling, and composting. The inventory data include gases and leachate from landfills, air emissions and energy recovery from incinerators, energy (and emission) savings from recycling, composting gases, and transport pollution. The impact assessment results for climate change, acidification, and ecotoxicity show that the incineration of materials imposes considerable harm to both human health and the environment, especially for the burning of plastics, paper/cardboard, and ferrous metals. The results also show that, although some amount of energy can be derived from the incineration of wastes, these benefits are outweighed by the air pollution (heavy metals and dioxins/furans) that incinerators produce. For Singapore, landfill gases and leachate generate minimal environmental damage because of the nation's policy to landfill only 10% of the total disposed wastes. Land transportation and separation of waste materials also pose minimal environmental damage. However, sea transportation to the landfill could contribute significantly to acidification because of the emissions of sulfur oxides and nitrogen oxides from barges. The composting of horticultural wastes hardly imposes any environmental damage. Out of all the waste strategies, the recycling of wastes offers the best solution for environmental protection and improved human health for the nation. Significant emission savings can be realized through recycling.

The Paravascular Pathway for Brain Waste Clearance: Current Understanding, Significance and Controversy

Directory of Open Access Journals (Sweden)

Andrew Bacyinski

2017-11-01

Full Text Available The paravascular pathway, also known as the “glymphatic” pathway, is a recently described system for waste clearance in the brain. According to this model, cerebrospinal fluid (CSF enters the paravascular spaces surrounding penetrating arteries of the brain, mixes with interstitial fluid (ISF and solutes in the parenchyma, and exits along paravascular spaces of draining veins. Studies have shown that metabolic waste products and solutes, including proteins involved in the pathogenesis of neurodegenerative diseases such as amyloid-beta, may be cleared by this pathway. Consequently, a growing body of research has begun to explore the association between glymphatic dysfunction and various disease states. However, significant controversy exists in the literature regarding both the direction of waste clearance as well as the anatomical space in which the waste-fluid mixture is contained. Some studies have found no evidence of interstitial solute clearance along the paravascular space of veins. Rather, they demonstrate a perivascular pathway in which waste is cleared from the brain along an anatomically distinct perivascular space in a direction opposite to that of paravascular flow. Although possible explanations have been offered, none have been able to fully reconcile the discrepancies in the literature, and many questions remain. Given the therapeutic potential that a comprehensive understanding of brain waste clearance pathways might offer, further research and clarification is highly warranted.

The Paravascular Pathway for Brain Waste Clearance: Current Understanding, Significance and Controversy.

Science.gov (United States)

Bacyinski, Andrew; Xu, Maosheng; Wang, Wei; Hu, Jiani

2017-01-01

The paravascular pathway, also known as the "glymphatic" pathway, is a recently described system for waste clearance in the brain. According to this model, cerebrospinal fluid (CSF) enters the paravascular spaces surrounding penetrating arteries of the brain, mixes with interstitial fluid (ISF) and solutes in the parenchyma, and exits along paravascular spaces of draining veins. Studies have shown that metabolic waste products and solutes, including proteins involved in the pathogenesis of neurodegenerative diseases such as amyloid-beta, may be cleared by this pathway. Consequently, a growing body of research has begun to explore the association between glymphatic dysfunction and various disease states. However, significant controversy exists in the literature regarding both the direction of waste clearance as well as the anatomical space in which the waste-fluid mixture is contained. Some studies have found no evidence of interstitial solute clearance along the paravascular space of veins. Rather, they demonstrate a perivascular pathway in which waste is cleared from the brain along an anatomically distinct perivascular space in a direction opposite to that of paravascular flow. Although possible explanations have been offered, none have been able to fully reconcile the discrepancies in the literature, and many questions remain. Given the therapeutic potential that a comprehensive understanding of brain waste clearance pathways might offer, further research and clarification is highly warranted.

Waste minimization in a petrochemical company

Energy Technology Data Exchange (ETDEWEB)

Anan, Marcelo [Oxiteno S.A., Industria e Comercio, Sao Paulo, SP (Brazil)

1994-12-31

A way to manage industrial effluents consists in reducing their generation or treating them when elimination or minimization is economically unachievable. This work aims to present the modifications adopted in a petrochemical plant to adequate and, or, reduce the generation of industrial effluent. 8 refs., 3 figs.

Waste minimization in a petrochemical company

Energy Technology Data Exchange (ETDEWEB)

Anan, Marcelo [Oxiteno S.A., Industria e Comercio, Sao Paulo, SP (Brazil)

1993-12-31

A way to manage industrial effluents consists in reducing their generation or treating them when elimination or minimization is economically unachievable. This work aims to present the modifications adopted in a petrochemical plant to adequate and, or, reduce the generation of industrial effluent. 8 refs., 3 figs.

Chemical analysis for waste management in paint industries

International Nuclear Information System (INIS)

Nawaz, Z.; Naveed, S.; Shiekh, N.A.; Sagheer, K.

2005-01-01

The chemical analysis of paint industries waste has been carried out; the main emission sources are the heating of raw materials and lacquer. Also the waste from other applications and production contains high concentration of heavy metals, VOC's, COD, TDS with notable acidity and alkalinity. Based on the analysis it was observed that the major losses of production could be minimized. Further toxic effects of the waste material can be minimized. In this reference measures to minimize production losses should be adopted along with the proper management. These laboratory results also lead to the areas of emissions and waste production during manufacturing process. Solutions have been proposed for process development and integrated waste minimization. (author)

Waste management and climate protection. Contribution of Bavarian waste management for greenhouse gas minimization; Abfallwirtschaft und Klimaschutz. Beitrag der bayerischen Abfallwirtschaft zur Treibhausgas-Minderung

Energy Technology Data Exchange (ETDEWEB)

Peche, R.; Kreibe, S. [bifa Umweltinstitut, Augsburg (Germany)

2007-08-15

bifa created a material flow model for approximately 23 million tons of Bavarian municipal and industrial waste that incorporates collection of waste, waste disposal and processing and treatment of residual material. bifa determined the influence of these material flows on emissions of greenhouse gases. The analysis shows that the Bavarian waste management achieved a reduction of greenhouse gases in the municipal and industrial waste sector that amounted to 3.2 million tons of carbon dioxide equivalents (CO{sub 2}E) in 2003, thus reducing environmental impact considerably. To see the overall reduction of greenhouse gases it is however necessary to compare the system of waste collection, waste treatment and waste processing with a fictitious scenario of waste disposal exclusively via landfill. This would cause an environmental load of 9.58 million tons CO{sub 2}E. Together with the amount of reduction attained in 2003, an overall reduction of greenhouse gas emissions of 12.78 millions tons CO{sub 2}E has thus been achieved by the Bavarian waste management. Analysis of possible future waste processing and waste avoidance measures showed two areas with significant additional potential for the reduction of greenhouse gas emissions. One is waste avoidance - e. g. through increased municipal counselling - however, this is difficult to realize. The other possibility is the optimisation of bio-waste processing. (orig.)

Solid waste management

OpenAIRE

Srebrenkoska, Vineta; Golomeova, Saska; Zhezhova, Silvana

2013-01-01

Waste is unwanted or useless materials from households, industry, agriculture, hospitals. Waste materials in solid state are classified as solid waste. Increasing of the amount of solid waste and the pressure what it has on the environment, impose the need to introduce sustainable solid waste management. Advanced sustainable solid waste management involves several activities at a higher level of final disposal of the waste management hierarchy. Minimal use of material and energy resources ...

Harmful Waste Process

International Nuclear Information System (INIS)

Ki, Mun Bong; Lee, Shi Jin; Park, Jun Seok; Yoon, Seok Pyo; Lee, Jae Hyo; Jo, Byeong Ryeol

2008-08-01

This book gives descriptions of processing harmful waste, including concerned law and definition of harmful waste, current conditions and generation of harmful waste in Korea, international condition of harmful waste, minimizing of generation of harmful waste, treatment and storage. It also tells of basic science for harmful waste disposal with physics, chemistry, combustion engineering, microbiology and technique of disposal such as physical, chemical, biological process, stabilizing and solidification, incineration and waste in landfill.

Solid medical waste

DEFF Research Database (Denmark)

Udofia, Emilia Asuquo; Gulis, Gabriel; Fobil, Julius

2017-01-01

BACKGROUND: Solid medical waste (SMW) in households is perceived to pose minimal risks to the public compared to SMW generated from healthcare facilities. While waste from healthcare facilities is subject to recommended safety measures to minimize risks to human health and the environment, similar...... waste in households is often untreated and co-mingled with household waste which ends up in landfills and open dumps in many African countries. In Ghana, the management of this potentially hazardous waste stream at household and community level has not been widely reported. The objective of this study...... likely to report harm in the household (OR 2.75, 95%CI 1.15-6.54). CONCLUSION: The belief that one can be harmed by diseases associated with SMW influenced reporting rates in the study area. Disposal practices suggest the presence of unwanted medicines and sharps in the household waste stream conferring...

Removal of contaminants from equipment and debris and waste minimization using TechXtract{reg_sign} technology

Energy Technology Data Exchange (ETDEWEB)

Bonem, M.W. [EET, Inc., Bellaire, TX (United States)

1997-10-01

Under this Program Research and Development Agreement (PRDA), EET, Inc., is extending its proprietary TechXtract{reg_sign} chemical decontamination technology into an effective, economical, integrated contaminant removal system. This integrated system will consist of a series of decontamination baths using the TechXtract{reg_sign} chemical formulas, followed by a waste treatment process that will remove the contaminants from the spent chemicals. Sufficient decontamination will result so that materials can be released without restriction after they have been treated, even those materials that have traditionally been considered to be {open_quotes}undecontaminable.{close_quotes} The secondary liquid waste will then be treated to separate any hazardous and radioactive contaminants, so that the spent chemicals and wastewater can be discharged through conventional, permitted outlets. The TechXtract{reg_sign} technology is a unique process that chemically extracts hazardous contaminants from the surface and substrate of concrete, steel, and other solid materials. This technology has been used successfully to remove contaminants as varied as PCBs, radionuclides, heavy metals, and hazardous organics. The process` advantage over other alternatives is its effectiveness in safe and consistent extraction of subsurface contamination. TechXtract{reg_sign} is a proprietary process developed, owned, and provided by EET, Inc. The objective of the PRDA is to demonstrate on a full-scale basis an economical system for decontaminating equipment and debris, with further treatment of secondary waste streams to minimize waste volumes. Contaminants will be removed from the contaminated items to levels where they can be released for unrestricted use. The entire system will be designed with maximum flexibility and automation in mind.

Removal of contaminants from equipment and debris and waste minimization using TechXtract reg-sign technology

International Nuclear Information System (INIS)

Bonem, M.W.

1997-01-01

Under this Program Research and Development Agreement (PRDA), EET, Inc., is extending its proprietary TechXtract reg-sign chemical decontamination technology into an effective, economical, integrated contaminant removal system. This integrated system will consist of a series of decontamination baths using the TechXtract reg-sign chemical formulas, followed by a waste treatment process that will remove the contaminants from the spent chemicals. Sufficient decontamination will result so that materials can be released without restriction after they have been treated, even those materials that have traditionally been considered to be open-quotes undecontaminable.close quotes The secondary liquid waste will then be treated to separate any hazardous and radioactive contaminants, so that the spent chemicals and wastewater can be discharged through conventional, permitted outlets. The TechXtract reg-sign technology is a unique process that chemically extracts hazardous contaminants from the surface and substrate of concrete, steel, and other solid materials. This technology has been used successfully to remove contaminants as varied as PCBs, radionuclides, heavy metals, and hazardous organics. The process' advantage over other alternatives is its effectiveness in safe and consistent extraction of subsurface contamination. TechXtract reg-sign is a proprietary process developed, owned, and provided by EET, Inc. The objective of the PRDA is to demonstrate on a full-scale basis an economical system for decontaminating equipment and debris, with further treatment of secondary waste streams to minimize waste volumes. Contaminants will be removed from the contaminated items to levels where they can be released for unrestricted use. The entire system will be designed with maximum flexibility and automation in mind

Significance of waste incineration in Germany; Stellenwert der Abfallverbrennung in Deutschland

Energy Technology Data Exchange (ETDEWEB)

NONE

2008-10-15

The report on the relevance of waste incineration in Germany is covering the following issues: change of the issue waste incineration in the last century, the controversy on waste incineration in the 80ies; environmental relevance of waste incineration; utilization of incineration residues; contribution to environmental protection; possible hazards for human health due are waste incinerator plants; the central challenges of waste incineration today; potential restraints to energy utilization in thermal waste processing; optimization of the energetic utilization of municipal wastes; future of the waste management and the relevance of waste incineration.

1997 annual report on waste generation and waste minimization progress as required by DOE Order 5400.1, Hanford Site

International Nuclear Information System (INIS)

Segall, P.

1998-01-01

Hanford's missions are to safely clean up and manage the site's legacy wastes, and to develop and deploy science and technology. Through these missions Hanford will contribute to economic diversification of the region. Hanford's environmental management or cleanup mission is to protect the health and safety of the public, workers, and the environment; control hazardous materials; and utilize the assets (people, infra structure, site) for other missions. Hanford's science and technology mission is to develop and deploy science and technology in the service of the nation including stewardship of the Hanford Site. Pollution Prevention is a key to the success of these missions by reducing the amount of waste to be managed and identifying/implementing cost effective waste reduction projects. Hanford's original mission, the production of nuclear materials for the nation's defense programs, lasted more than 40 years, and like most manufacturing operations, Hanford's operations generated large quantities of waste and pollution. However, the by-products from Hanford operations pose unique problems like radiation hazards, vast volumes of contaminated water and soil, and many contaminated structures including reactors, chemical plants and evaporation ponds. The cleanup activity is an immense and challenging undertaking, which includes characterization and decommissioning of 149 single shell storage tanks, treating 28 double shell tanks, safely disposing of over 2,100 metric tons of spent nuclear fuel stored on site, removing numerous structures, and dealing with significant solid waste, ground water, and land restoration issues

The potential significance of microbial activity in radioactive waste disposal

International Nuclear Information System (INIS)

McCabe, A.M.

1987-12-01

The aim of this report is to assess the potential significance of microbial activity in radioactive waste disposal. It outlines the major factors which need to be considered in order to evaluate the importance of microbiological action. These include water and nutritional sources (particularly carbon) hostile conditions (particularly the effects of radiation and pH), the establishment of pH micro-environments and the degradative effect of microbial metabolic by-products on the disposed waste forms. Before an active microbial population can develop there are certain basic requirements for life. These are outlined and the possibility of colonisation occurring within the chemical, radiological and nutritional constraints of a repository are considered. Once colonisation is assumed, the effect of microbial activity is discussed under five headings, i.e. (i) direct attack, (ii) physical disruption (which includes consideration of fissuring processes and void formation), (iii) gas generation (which may be of particular importance), (iv) radionuclide uptake and finally (v) alteration of groundwater chemistry. Particular attention is paid to the possibility of environments becoming established both within the waste form itself (allowing microbes to attack from the inside of the repository outward) or attack on the encapsulant materials (microbes attacking from the outside inward). (author)

Certification plan transuranic waste: Hazardous Waste Handling Facility

International Nuclear Information System (INIS)

1992-06-01

The purpose of this plan is to describe the organization and methodology for the certification of transuranic (TRU) waste handled in the Hazardous Waste Handling Facility at Lawrence Berkeley Laboratory (LBL). The plan incorporates the applicable elements of waste reduction, which include both up-front minimization and end-product treatment to reduce the volume and toxicity of the waste; segregation of the waste as it applies to certification; an executive summary of the Quality Assurance Implementing Management Plan (QAIMP) for the HWBF; and a list of the current and planned implementing procedures used in waste certification

Overcoming mixed waste management obstacles - A company wide approach

International Nuclear Information System (INIS)

Buckley, R.N.

1996-01-01

The dual regulation of mixed waste by the Nuclear Regulatory Commission and the Environmental Protection Agency has significantly complicated the treatment, storage and disposal of this waste. Because of the limited treatment and disposal options available, facilities generating mixed waste are also being forced to acquire storage permits to meet requirements associated with the Resource Conservation and Recovery Act. Due to the burdens imposed by the regulatory climate, Entergy Operations has undertaken a proactive approach to managing its mixed waste. Their approach is company wide and simplistic in nature. Utilizing the peer groups to develop strategies and a company wide procedure for guidance on mixed waste activities, they have focused on areas where they have the most control and can achieve the greatest benefits from their efforts. A key aspect of the program includes training and employee awareness regarding mixed waste minimization practices. In addition, Entergy Operations is optimizing the implementation of regulatory provisions that facilitate more flexible management practices for mixed waste. This presentation focuses on the team approach to developing mixed waste managements programs and the utilization of innovative thinking and planning to minimize the regulatory burdens. It will also describe management practices and philosophies that have provided more flexibility in implementing a safe and effective company wide mixed waste management program

Proceedings of the US Department of Energy Office of Environmental Restoration and Waste Management: Waste reduction workshop 7

International Nuclear Information System (INIS)

1991-11-01

The focus of this workshop was on goal setting and the methods of establishing meaningful goals for a waste minimization program. These workshops assist DOE waste-generating sites in implementing waste minimization plans and programs, thus providing for optimal waste reduction within the DOE complex. All wastes are considered liquid, solid, and airborne within the categories of high-level waste, transuranic waste (TRU), low-level waste (LLW), hazardous waste, mixed waste, office waste, and sanitary waste. Topics of discussion within workshops encompass a wide range of subjects. Subjects include any method or technical activity from waste generation to disposal, such as process design or improvements, substitution of materials, waste segregation and recycling/reuse, waste treatment and processing, and administrative controls (procurement and waste awareness training). Consideration is also given to activities for remedial action and for decontamination and decommissioning

Residues from waste incineration. Final report

Energy Technology Data Exchange (ETDEWEB)

Astrup, T.; Juul Pedersen, A.; Hyks, J.; Frandsen, F.J.

2009-08-15

The overall objective of the project was to improve the understanding of the formation and characteristics of residues from waste incineration. This was done focusing on the importance of the waste input and the operational conditions of the furnace. Data and results obtained from the project have been discussed in this report according to the following three overall parts: i) mass flows and element distribution, ii) flue gas/particle partitioning and corrosion/deposition aspects, and iii) residue leaching. This has been done with the intent of structuring the discussion while tacitly acknowledging that these aspects are interrelated and cannot be separated. Overall, it was found that the waste input composition had significant impact of the characteristics of the generated residues. A similar correlation between operational conditions and residue characteristics could not be observed. Consequently, the project recommend that optimization of residue quality should focus on controlling the waste input composition. The project results showed that including specific waste materials (and thereby also excluding the same materials) may have significant effects on the residue composition, residue leaching, aerosol and deposit formation.It is specifically recommended to minimize Cl in the input waste. Based on the project results, it was found that a significant potential for optimization of waste incineration exist. (author)

Operating Procedures to Identify Wastes of Decommissioning

International Nuclear Information System (INIS)

Gatea, M.A.

2016-01-01

There are a number of sites in Iraq which have been used for nuclear activities and which contain potentially significant amounts of radioactive material. Many of these sites suffered substantial physical damage during the Gulf Wars as well as the challenging of the difficult security situation in the country.The destruction of the former nuclear facilities during the 1991 Gulf war aggravated the problem. As a result of these events, many of these nuclear facilities have lost their containment of the radioactive material and it now has an increased potential to be dispersed into the environment.Iraqi Decommissioning Directorate (IDD) is one of the Ministry of Science and Technology (MoST) formations. It deals with decommissioning of former Iraqi nuclear sites. It considers a producer of radioactive waste.Therefore, waste management represents the vital requirement to work accomplishment.The work carries out on-site waste pretreatment which considers as a minimization of waste management.W M is necessary to: Segregate 'at source' as much materials as possible to minimize quantities of radioactive waste, clear or exempt as much materials as possible and decontaminate and recycle as much radioactive waste as possible. And in more general terms: to control and account for radioactive waste to protect human health and the environment, to make sure we do not leave unnecessary burdens for future generations, to concentrate, contain and isolate the waste from the environment therefore, this make any releases to the environment to be restricted and subject to regulatory control.This procedure applies on-site waste pretreatment which comprises segregating, characterizing, minimizing, classifying, packaging and relocating of generated wastes during decommissioning of destroyed nuclear facilities. The stationary waste treatment activities are the responsibility of RWTD/MoST.The (RPC/MoE) is the national regulatory body during the whole radioactive waste management

Process Waste Assessment - Paint Shop

International Nuclear Information System (INIS)

Phillips, N.M.

1993-06-01

This Process Waste Assessment was conducted to evaluate hazardous wastes generated in the Paint Shop, Building 913, Room 130. Special attention is given to waste streams generated by the spray painting process because it requires a number of steps for preparing, priming, and painting an object. Also, the spray paint booth covers the largest area in R-130. The largest and most costly waste stream to dispose of is open-quote Paint Shop wasteclose quotes -- a combination of paint cans, rags, sticks, filters, and paper containers. These items are compacted in 55-gallon drums and disposed of as solid hazardous waste. Recommendations are made for minimizing waste in the Paint Shop. Paint Shop personnel are very aware of the need to minimize hazardous wastes and are continuously looking for opportunities to do so

Sustainable Waste Management for Green Highway Initiatives

Directory of Open Access Journals (Sweden)

Husin Nur Illiana

2016-01-01

Full Text Available Green highway initiative is the transportation corridors based on sustainable concept of roadway. It incorporates both transportation functionality and ecological requirements. Green highway also provides more sustainable construction technique that maximizes the lifespan of highway. Waste management is one of the sustainable criterias in the elements of green highway. Construction of highway consumes enormous amounts of waste in term of materials and energy. These wastes need to be reduce to sustain the environment. This paper aims to identify the types of waste produced from highway construction. Additionally, this study also determine the waste minimization strategy and waste management practiced.. This study main focus are construction and demolition waste only. The methodology process begin with data collection by using questionnaire survey. 22 concession companies listed under Lembaga Lebuhraya Malaysia acted as a respondent. The questionnaires were distributed to all technical department staffs. The data received was analyzed using IBM SPSS. The results shows the most production of waste is wood, soil, tree root and concrete. The least production of waste is metal. For waste minimization, the best waste minimization is reuse for all type of waste except for tree root and stump. Whereas, the best waste management is providing strategic plan. The least practice for waste management is recording the quantity of waste.

The differences between emission, waste, and a good, and their significance to waste management policy

International Nuclear Information System (INIS)

Holm-Mueller, K.

1994-01-01

This paper defines the transportability of solid waste as its major difference compared to emissions. Several specific possibilities for politics dealing with the problems of solid waste are deduced from this characteristic. The difference between solid waste and good lies in the valuation of objects. As is shown the negative valuation of waste has a great influence on the effect of possible politics derived in part one of this paper. (orig.) [de

Managing a mixed waste program

International Nuclear Information System (INIS)

Koch, J.D.

1994-01-01

IT Corporation operates an analytical laboratory in St. Louis capable of analyzing environmental samples that are contaminated with both chemical and radioactive materials. Wastes generated during these analyses are hazardous in nature; some are listed wastes others exhibit characteristic hazards. When the original samples contain significant quantities of radioactive material, the waste must be treated as a mixed waste. A plan was written to document the waste management program describing the management of hazardous, radioactive and mixed wastes. This presentation summarizes the methods employed by the St. Louis facility to reduce personnel exposures to the hazardous materials, minimize the volume of mixed waste and treat the materials prior to disposal. The procedures that are used and the effectiveness of each procedure will also be discussed. Some of the lessons that have been learned while dealing with mixed wastes will be presented as well as the solutions that were applied. This program has been effective in reducing the volume of mixed waste that is generated. The management program also serves as a method to manage the costs of the waste disposal program by effectively segregating the different wastes that are generated

Pollution prevention opportunity assessment for Building 922 solid office waste

International Nuclear Information System (INIS)

Phillips, N.M.

1995-01-01

Building 922 houses all of SNL/California's ES and H Departments: Health Protection, Environmental Protection, Safety, and Environmental Operations. It covers approximately 10,000 square feet and houses about 80 people. The office personnel generate nonhazardous solid office wastes in their daily activities. To determine the types and amounts of waste generated, a special PPOA sorting team sorted all of the trash collected from the building for a period of one-week (including paper and aluminum cans in the recycling bins). The team sorted the trash into major categories: paper, plastic, metals, glass, wet garbage, rest room waste, and miscellaneous materials. They then sorted it into subcategories within each major category. Rest room waste was collected but not sorted. The waste in each category was weighed separately. The total amount of trash collected during the week was approximately 168.8 kg (371.4 lbs). The results of this PPOA indicate that SNL/California is minimizing most nonhazardous office waste and reductions planned for the near future will add significantly to the minimization efforts

Nuclear waste management at DOE

International Nuclear Information System (INIS)

Perge, A.F.

1979-01-01

DOE is responsible for interim storage for some radioactive wastes and for the disposal for most of them. Of the wastes that have to be managed a significant part are a result of treatment systems and devices for cleaning gases. The long term waste management objectives place minimal reliance on surveillance and maintenance. Thus, the concerns about the chemical, thermal, and radiolytic degradation of wastes require technology for converting the wastes to forms acceptable for long term isolation. The strategy of the DOE airborne radioactive waste management program is to increase the service life and reliability of filters; to reduce filter wastes; and in anticipation of regulatory actions that would require further reductions in airborne radioactive releases from defense program facilities, to develop improved technology for additional collection, fixation, and long-term management of gaseous wastes. Available technology and practices are adequate to meet current health and safety standards. The program is aimed primarily at cost effective improvements, quality assurance, and the addition of new capability in areas where more restrictive standards seem likely to apply in the future

Significance of actinide chemistry for the long-term safety of waste disposal

International Nuclear Information System (INIS)

Kim, Jae Il

2006-01-01

A geochemical approach to the long-term safety of waste disposal is discussed in connection with the significance of actinides, which shall deliver the major radioactivity inventory subsequent to the relatively short-term decay of fission products. Every power reactor generates transuranic (TRU) elements: plutonium and minor actinides (Np, Am, Cm), which consist chiefly of long-lived nuclides emitting alpha radiation. The amount of TRU actinides generated in a fuel life period is found to be relatively small (about 1 wt% or less in spent fuel) but their radioactivity persists many hundred thousands years. Geological confinement of waste containing TRU actinides demands, as a result, fundamental knowledge on the geochemical behavior of actinides in the repository environment for a long period of time. Appraisal of the scientific progress in this subject area is the main objective of the present paper. Following the introductory discussion on natural radioactivities, the nuclear fuel cycle is briefly brought up with reference to actinide generation and waste disposal. As the long-term disposal safety concerns inevitably with actinides, the significance of the aquatic actinide chemistry is summarized in two parts: the fundamental properties relevant to their aquatic behavior and the geochemical reactions in nanoscopic scale. The constrained space of writing allows discussion on some examples only, for which topics of the primary concern are selected, e.g. apparent solubility and colloid generation, colloid-facilitated migration, notable speciation of such processes, etc. Discussion is summed up to end with how to make a geochemical approach available for the long-term disposal safety of nuclear waste or for the Performance Assessment (PA) as known generally

Conversion of finished leather waste incorporated with plant fibers into value added consumer products - An effort to minimize solid waste in Ethiopia.

Science.gov (United States)

Teklay, A; Gebeyehu, G; Getachew, T; Yaynshet, T; Sastry, T P

2017-10-01

Presently, the leftovers from leather product industries are discarded as waste in Ethiopia. The objective of the present study was therefore, to prepare composite sheets by incorporating various plant fibers like enset (Ensete ventricosum), hibiscus (Hibiscus cannabinus), jute (Corchorus trilocularis L.), palm (Phoenix dactylifera) and sisal (Agave sisal) in various proportions into the leather waste. Resin binder (RB) and natural rubber latex (NRL) were used as binding agents for the preparation of the composite sheets. The composite sheets prepared were characterized for their physicochemical properties (tensile strength, elongation at break, stitch tear strength, water absorption, water desorption and flexing strength). Composite sheets prepared using RB having 10% hibiscus, 20% palm and 40% sisal fibers showed better mechanical properties than their respective controls. In composite sheets prepared using NRL having 30% jute fiber exhibited better mechanical properties than its control. Most of the plant fibers used in this study played a role in increasing the performance of the sheets. However, as seen from the results, the contribution of these plant fibers on performance of the composite sheets prepared is dependent on the ratio used and the nature of binder. The SEM studies have exhibited the composite nature of the sheets and FTIR studies have shown the functional groups of collagen protein, cellulose and binders. The prepared sheets were used as raw materials for preparation of items like stiff hand bags, ladies' purse, keychain, chappal upper, wallet, wall cover, mouse pad and other interior decorating products. By preparing such value added products, we can reduce solid waste; minimize environmental pollution and thereby securing environmental sustainability. Copyright © 2017 Elsevier Ltd. All rights reserved.

Chelation technology: a promising green approach for resource management and waste minimization.

Science.gov (United States)

Chauhan, Garima; Pant, K K; Nigam, K D P

2015-01-01

Green chemical engineering recognises the concept of developing innovative environmentally benign technologies to protect human health and ecosystems. In order to explore this concept for minimizing industrial waste and for reducing the environmental impact of hazardous chemicals, new greener approaches need to be adopted for the extraction of heavy metals from industrial waste. In this review, a range of conventional processes and new green approaches employed for metal extraction are discussed in brief. Chelation technology, a modern research trend, has shown its potential to develop sustainable technology for metal extraction from various metal-contaminated sites. However, the interaction mechanism of ligands with metals and the ecotoxicological risk associated with the increased bioavailability of heavy metals due to the formation of metal-chelant complexes is still not sufficiently explicated in the literature. Therefore, a need was felt to provide a comprehensive state-of-the-art review of all aspects associated with chelation technology to promote this process as a green chemical engineering approach. This article elucidates the mechanism and thermodynamics associated with metal-ligand complexation in order to have a better understanding of the metal extraction process. The effects of various process parameters on the formation and stability of complexes have been elaborately discussed with respect to optimizing the chelation efficiency. The non-biodegradable attribute of ligands is another important aspect which is currently of concern. Therefore, biotechnological approaches and computational tools have been assessed in this review to illustrate the possibility of ligand degradation, which will help the readers to look for new environmentally safe mobilizing agents. In addition, emerging trends and opportunities in the field of chelation technology have been summarized and the diverse applicability of chelation technology in metal extraction from

Radioactive waste management - the Indian scenario

International Nuclear Information System (INIS)

Raj, Kanwar

2008-01-01

In India, nuclear power generation programme and application of radioisotopes for health care and various other application is increasing steadily. With resultant increase in generation of radioactive waste, emphasis is on the minimization of generation of radioactive waste by deploying suitable processes and materials, segregation of waste streams at sources, recycle and re-use of useful components of waste and use of volume reduction techniques. The minimization of the radioactive waste is also essential to facilitate judicious use of the scarce land available for disposal, to reduce impact on the environment due to disposal and, finally to optimize the cost of radioactive waste management. This paper presents a bird's eye view of radioactive waste management programme in the country today

Integrated Waste Management Strategy and Radioactive Waste Forms for the 21st Century

International Nuclear Information System (INIS)

Dirk Gombert; Jay Roach

2007-01-01

The U.S. Department of Energy (DOE) Global Nuclear Energy Partnership (GNEP) was announced in 2006. As currently envisioned, GNEP will be the basis for growth of nuclear energy worldwide, using a closed proliferation-resistant fuel cycle. The Integrated Waste Management Strategy (IWMS) is designed to ensure that all wastes generated by fuel fabrication and recycling will have a routine disposition path making the most of feedback to fuel and recycling operations to eliminate or minimize byproducts and wastes. If waste must be generated, processes will be designed with waste treatment in mind to reduce use of reagents that complicate stabilization and minimize volume. The IWMS will address three distinct levels of technology investigation and systems analyses and will provide a cogent path from (1) research and development (R and D) and engineering scale demonstration, (Level I); to (2) full scale domestic deployment (Level II); and finally to (3) establishing an integrated global nuclear energy infrastructure (Level III). The near-term focus of GNEP is on achieving a basis for large-scale commercial deployment (Level II), including the R and D and engineering scale activities in Level I that are necessary to support such an accomplishment. Throughout these levels is the need for innovative thinking to simplify, including regulations, separations and waste forms to minimize the burden of safe disposition of wastes on the fuel cycle

Integrated Waste Management Strategy and Radioactive Waste Forms for the 21st Century

Energy Technology Data Exchange (ETDEWEB)

Dirk Gombert; Jay Roach

2007-03-01

The U. S. Department of Energy (DOE) Global Nuclear Energy Partnership (GNEP) was announced in 2006. As currently envisioned, GNEP will be the basis for growth of nuclear energy worldwide, using a closed proliferation-resistant fuel cycle. The Integrated Waste Management Strategy (IWMS) is designed to ensure that all wastes generated by fuel fabrication and recycling will have a routine disposition path making the most of feedback to fuel and recycling operations to eliminate or minimize byproducts and wastes. If waste must be generated, processes will be designed with waste treatment in mind to reduce use of reagents that complicate stabilization and minimize volume. The IWMS will address three distinct levels of technology investigation and systems analyses and will provide a cogent path from (1) research and development (R&D) and engineering scale demonstration, (Level I); to (2) full scale domestic deployment (Level II); and finally to (3) establishing an integrated global nuclear energy infrastructure (Level III). The near-term focus of GNEP is on achieving a basis for large-scale commercial deployment (Level II), including the R&D and engineering scale activities in Level I that are necessary to support such an accomplishment. Throughout these levels is the need for innovative thinking to simplify, including regulations, separations and waste forms to minimize the burden of safe disposition of wastes on the fuel cycle.

Plasma cleaning for waste minimization

Energy Technology Data Exchange (ETDEWEB)

Ward, P.P.

1993-07-01

Although plasma cleaning is a recognized substitute for solvent cleaning in removing organic contaminants, some universal problems in plasma cleaning processes prevent wider use of plasma techniques. Lack of understanding of the fundamental mechanisms of the process, unreliable endpoint detection techniques, and slow process times make plasma cleaning processes less than desirable. Our approach to address these plasma cleaning problems is described. A comparison of plasma cleaning rates of oxygen and oxygen/sulfur hexafluoride gases shows that fluorine-containing plasmas can enhance etch rates by 400% over oxygen alone. A discussion of various endpoint indication techniques is discussed and compared for application suitability. Work toward a plasma cleaning database is discussed. In addition to the global problems of plasma cleaning, an experiment where the specific mixed-waste problem of removal of machine oils from radioactive scrap metal is discussed.

Application of molten salt oxidation for the minimization and recovery of plutonium-238 contaminated wastes

International Nuclear Information System (INIS)

Wishau, R.

1998-05-01

Molten salt oxidation (MSO) is proposed as a 238 Pu waste treatment technology that should be developed for volume reduction and recovery of 238 Pu and as an alternative to the transport and permanent disposal of 238 Pu waste to the WIPP repository. In MSO technology, molten sodium carbonate salt at 800--900 C in a reaction vessel acts as a reaction media for wastes. The waste material is destroyed when injected into the molten salt, creating harmless carbon dioxide and steam and a small amount of ash in the spent salt. The spent salt can be treated using aqueous separation methods to reuse the salt and to recover 99.9% of the precious 238 Pu that was in the waste. Tests of MSO technology have shown that the volume of combustible TRU waste can be reduced by a factor of at least twenty. Using this factor the present inventory of 574 TRU drums of 238 Pu contaminated wastes is reduced to 30 drums. Further 238 Pu waste costs of $22 million are avoided from not having to repackage 312 of the 574 drums to a drum total of more than 4,600 drums. MSO combined with aqueous processing of salts will recover approximately 1.7 kilograms of precious 238 Pu valued at 4 million dollars (at $2,500/gram). Thus, installation and use of MSO technology at LANL will result in significant cost savings compared to present plans to transport and dispose 238 Pu TRU waste to the WIPP site. Using a total net present value cost for the MSO project as $4.09 million over a five-year lifetime, the project can pay for itself after either recovery of 1.6 kg of Pu or through volume reduction of 818 drums or a combination of the two. These savings show a positive return on investment

Integration of environmentally compatible soldering technologies for waste minimization

International Nuclear Information System (INIS)

Hosking, F.M.

1992-01-01

There has been a concentrated effort throughout the international microelectronics industry to phase out chlorofluorocarbon (CFC) materials and alleviate the serious problem of ozone depletion created by the release of CFCS. The development of more environmentally compatible manufacturing technologies is the cornerstone of this effort. Alternative materials and processes for cleaning and soldering have received special attention. Electronic. soldering typically utilizes rosin-based fluxes to promote solder wettability. Flux residues must be removed from the soldered parts when high product reliability is essential. Halogenated or CFC solvents have been the principle chemicals used to clean the residues. With the accelerated push to eliminate CFCs in the US by 1995, CFC-free solvents, aqueous-based cleaning, water soluble or ''no clean'' fluxes, and fluxless soldering technologies are being developed and quickly integrated into manufacturing practice. Sandia's Center for Solder Science and Technology has been ch g a variety of fluxless and alternative soldering technologies for DOE's waste minimization program. The work has focused on controlled atmosphere, laser, and ultrasonic fluxless soldering, protective metallic and organic coatings, and fluxes which have water soluble or low solids-based chemistries. With the increasing concern that Pb will also be banned from electronic soldering, Sandia has been characterizing the wetting, aging, and mechanical properties of Pb-fire solder alloys. The progress of these integrated studies will be discussed. Their impact on environmentally compatible manufacturing will be emphasized. Since there is no universal solution to the various environmental, safety, and health issues which currently face industry, the proposed technologies offer several complementary materials and processing options from which one can choose

Barriers to development and deployment of innovative waste minimization technologies

International Nuclear Information System (INIS)

Flores, E.A.; Donaghue, J.F.

1994-08-01

Increasing regulation and scrutiny is driving waste generators towards reducing the use of scarce natural resources and reducing or eliminating was streams. There is increasing emphasis on developing and deploying technologies that meet industry needs for recovering valuable materials in a cost-effective manner. At the Department of Energy's (DOE) Hanford Site, Battelle operates Pacific Northwest Laboratory (PNL). PNL's mission is to develop technologies to clean up the environment, and to assist industry in being competitive on a global scale. One such technology developed by PNL is the Waste Acid Detoxification and Reclamation (WADR) process. This technology recovers acids from metal-bearing spent solutions, separating out the metals (which are a valuable byproduct of the acid recycling operation) from the acids. WADR uses selective precipitation and distillation together in an innovative waste recycling technology. Selective precipitation removes the heavy metals, and vacuum distillation recovers clean acid. However, WADR and other innovative waste reduction technologies face numerous barriers to successful development and deployment in the field

Cost-benefit analysis for waste compaction alternatives at Lawrence Livermore National Laboratory: Addendum A to the Waste Minimization and Pollution Prevention Awareness Plan of May 31, 1991

International Nuclear Information System (INIS)

1992-01-01

This report presents a cost-benefit analysis of the potential procurement and operation of various solid waste compactors or of the use of commercial compaction services, for compaction of solid transuranic (TRU), low-level radioactive, hazardous, and mixed wastes at Lawrence Livermore National Laboratory (LLNL) Hazardous Waste Management (HWM) facilities. The cost-benefit analysis was conducted to determine if increased compaction capacity at HWM might afford the potential for significant waste volume reduction and annual savings in material, shipping, labor, and disposal costs

An interval-based possibilistic programming method for waste management with cost minimization and environmental-impact abatement under uncertainty.

Science.gov (United States)

Li, Y P; Huang, G H

2010-09-15

Considerable public concerns have been raised in the past decades since a large amount of pollutant emissions from municipal solid waste (MSW) disposal of processes pose risks on surrounding environment and human health. Moreover, in MSW management, various uncertainties exist in the related costs, impact factors and objectives, which can affect the optimization processes and the decision schemes generated. In this study, an interval-based possibilistic programming (IBPP) method is developed for planning the MSW management with minimized system cost and environmental impact under uncertainty. The developed method can deal with uncertainties expressed as interval values and fuzzy sets in the left- and right-hand sides of constraints and objective function. An interactive algorithm is provided for solving the IBPP problem, which does not lead to more complicated intermediate submodels and has a relatively low computational requirement. The developed model is applied to a case study of planning a MSW management system, where mixed integer linear programming (MILP) technique is introduced into the IBPP framework to facilitate dynamic analysis for decisions of timing, sizing and siting in terms of capacity expansion for waste-management facilities. Three cases based on different waste-management policies are examined. The results obtained indicate that inclusion of environmental impacts in the optimization model can change the traditional waste-allocation pattern merely based on the economic-oriented planning approach. The results obtained can help identify desired alternatives for managing MSW, which has advantages in providing compromised schemes under an integrated consideration of economic efficiency and environmental impact under uncertainty. Copyright 2010 Elsevier B.V. All rights reserved.

The Waste Treatment Plant, a Work in Progress

International Nuclear Information System (INIS)

Hamel, W. F. Jr.; Duncan, G. M.

2006-01-01

There are many challenges in the design and construction of Department of Energy's (DOE) Waste Treatment and Immobilization Plant (WTP) at the Hanford site. The plant is being built to process some 55 million gallons of radioactive waste from 177 underground tanks. Engineering and construction are progressing on this largest project in the DOE complex. This paper describes some of WTP's principal recent challenges and opportunities and how they are being addressed to minimize impact on the project, enhance the capabilities of the facilities, and reduce risk. A significant new development in 2005 was the need to account for higher seismic accelerations than originally specified for the facility structures and equipment. Efforts have centered on continuing design and construction with minimal risk, while the final seismic design spectra was developed. Other challenges include development of an alternative cesium ion exchange resin to minimize the risk from reliance on a single product, implementing advanced analytical techniques to improve laboratory performance, adopting a thinner walled high level waste (HLW) canister to reduce waste volume and mission duration, and commissioning a comprehensive external flowsheet review of the design, along with its underpinning technologies, and projected plant operability. These challenges make it clear that WTP is a work in progress, but the challenges are being successfully resolved as the design and construction move on to completion. (authors)

76 FR 59960 - Hazardous Waste Management System; Identification and Listing of Hazardous Waste; Withdrawal of...

Science.gov (United States)

2011-09-28

... Waste Management System; Identification and Listing of Hazardous Waste; Withdrawal of proposed rule... Permitting Division, Corrective Action and Waste Minimization Section (6PD-C), 1445 Ross Avenue, Dallas, TX... petition. A new petition will be required for this waste stream. List of Subjects in 40 CFR Part 261...

On eco-efficient technologies to minimize industrial water consumption

Science.gov (United States)

Amiri, Mohammad C.; Mohammadifard, Hossein; Ghaffari, Ghasem

2016-07-01

Purpose - Water scarcity will further stress on available water systems and decrease the security of water in many areas. Therefore, innovative methods to minimize industrial water usage and waste production are of paramount importance in the process of extending fresh water resources and happen to be the main life support systems in many arid regions of the world. This paper demonstrates that there are good opportunities for many industries to save water and decrease waste water in softening process by substituting traditional with echo-friendly methods. The patented puffing method is an eco-efficient and viable technology for water saving and waste reduction in lime softening process. Design/methodology/approach - Lime softening process (LSP) is a very sensitive process to chemical reactions. In addition, optimal monitoring not only results in minimizing sludge that must be disposed of but also it reduces the operating costs of water conditioning. Weakness of the current (regular) control of LSP based on chemical analysis has been demonstrated experimentally and compared with the eco-efficient puffing method. Findings - This paper demonstrates that there is a good opportunity for many industries to save water and decrease waste water in softening process by substituting traditional method with puffing method, a patented eco-efficient technology. Originality/value - Details of the required innovative works to minimize industrial water usage and waste production are outlined in this paper. Employing the novel puffing method for monitoring of lime softening process results in saving a considerable amount of water while reducing chemical sludge.

Operational tank leak detection and minimization during retrieval

International Nuclear Information System (INIS)

Hertzel, J.S.

1996-03-01

This report evaluates the activities associated with the retrieval of wastes from the single-shell tanks proposed under the initial Single-Shell Tank Retrieval System. This report focuses on minimizing leakage during retrieval by using effective leak detection and mitigating actions. After reviewing the historical data available on single-shell leakage, and evaluating current leak detection technology, this report concludes that the only currently available leak detection method which can function within the most probable leakage range is the mass balance system. If utilized after each sluicing campaign, this method should allow detection at a leakage value well below the leakage value where significant health effects occur which is calculated for each tank. Furthermore, this report concludes that the planned sequence or sluicing activities will serve to further minimize the probability and volume of leaks by keeping liquid away from areas with the greatest potential for leaking. Finally, this report identifies a series of operational responses which when used in conjunction with the recommended sluicing sequence and leak detection methods will minimize worker exposure and environmental safety health risks

Application of molten salt oxidation for the minimization and recovery of plutonium-238 contaminated wastes

Energy Technology Data Exchange (ETDEWEB)

Wishau, R.

1998-05-01

Molten salt oxidation (MSO) is proposed as a {sup 238}Pu waste treatment technology that should be developed for volume reduction and recovery of {sup 238}Pu and as an alternative to the transport and permanent disposal of {sup 238}Pu waste to the WIPP repository. In MSO technology, molten sodium carbonate salt at 800--900 C in a reaction vessel acts as a reaction media for wastes. The waste material is destroyed when injected into the molten salt, creating harmless carbon dioxide and steam and a small amount of ash in the spent salt. The spent salt can be treated using aqueous separation methods to reuse the salt and to recover 99.9% of the precious {sup 238}Pu that was in the waste. Tests of MSO technology have shown that the volume of combustible TRU waste can be reduced by a factor of at least twenty. Using this factor the present inventory of 574 TRU drums of {sup 238}Pu contaminated wastes is reduced to 30 drums. Further {sup 238}Pu waste costs of $22 million are avoided from not having to repackage 312 of the 574 drums to a drum total of more than 4,600 drums. MSO combined with aqueous processing of salts will recover approximately 1.7 kilograms of precious {sup 238}Pu valued at 4 million dollars (at $2,500/gram). Thus, installation and use of MSO technology at LANL will result in significant cost savings compared to present plans to transport and dispose {sup 238}Pu TRU waste to the WIPP site. Using a total net present value cost for the MSO project as $4.09 million over a five-year lifetime, the project can pay for itself after either recovery of 1.6 kg of Pu or through volume reduction of 818 drums or a combination of the two. These savings show a positive return on investment.

Certification Plan, Radioactive Mixed Waste Hazardous Waste Handling Facility

International Nuclear Information System (INIS)

Albert, R.

1992-01-01

The purpose of this plan is to describe the organization and methodology for the certification of radioactive mixed waste (RMW) handled in the Hazardous Waste Handling Facility at Lawrence Berkeley Laboratory (LBL). RMW is low-level radioactive waste (LLW) or transuranic (TRU) waste that is co-contaminated with dangerous waste as defined in the Westinghouse Hanford Company (WHC) Solid Waste Acceptance Criteria (WAC) and the Washington State Dangerous Waste Regulations, 173-303-040 (18). This waste is to be transferred to the Hanford Site Central Waste Complex and Burial Grounds in Hanford, Washington. This plan incorporates the applicable elements of waste reduction, which include both up-front minimization and end-product treatment to reduce the volume and toxicity of the waste; segregation of the waste as it applies to certification; an executive summary of the Waste Management Quality Assurance Implementing Management Plan (QAIMP) for the HWHF (Section 4); and a list of the current and planned implementing procedures used in waste certification

New Technological Options to Manage High Level Waste

International Nuclear Information System (INIS)

Gonzalez Romero, E. M.

2007-01-01

Nuclear energy renaissance and its expansion in time and space has renewed the need for minimization technologies applicable to nuclear wastes. The minimization technologies include new power reactor concepts, Generation IV, and dedicated technologies like Partitioning and Transmutation of the actinides contained in the spent fuel. These technologies apply the principle of classification and recycling to the spent fuel to transform what at present is an environmental hazard into an energy source. the waste minimization technologies are also relevant for countries planning the reduction or phase-out of nuclear energy, as they will allow minimizing the size and number of the final waste repositories. Present estimations indicate that reductions as large as a factor 100 in the amount (radiotoxicity) of long lived nuclear waste are feasibly, with a modest increase on the final electricity cost. (Author)

Minimal alteration of montmorillonite following long-term interaction with natural alkaline groundwater: Implications for geological disposal of radioactive waste

International Nuclear Information System (INIS)

Milodowski, Antoni E.; Norris, Simon; Alexander, W.Russell

2016-01-01

Bentonite is one of the more safety-critical components of the engineered barrier system in the disposal concepts developed for many types of radioactive waste. Bentonite is utilised because of its favourable properties which include plasticity, swelling capacity, colloid filtration, low hydraulic conductivity, high retardation of key radionuclides and stability in geological environments of relevance to waste disposal. However, bentonite is unstable under the highly alkaline conditions induced by Ordinary Portland Cement (OPC: initial porewater pH > 13) and this has driven interest in using low alkali cements (initial porewater pH9-11) as an alternative to OPC. To build a robust safety case for a repository for radioactive wastes, it is important to have supporting natural analogue data to confirm understanding of the likely long-term performance of bentonite in these lower alkali conditions. In Cyprus, the presence of natural bentonite in association with natural alkaline groundwater permits the zones of potential bentonite/alkaline water reaction to be studied as an analogy of the potential reaction between low alkali cement leachates and the bentonite buffer in the repository. Here, the results indicate that a cation diffusion front has moved some metres into the bentonite whereas the bentonite reaction front is restricted to a few millimetres into the clay. This reaction front shows minimal reaction of the bentonite (volumetrically, less than 1% of the bentonite), with production of a palygorskite secondary phase following reaction of the primary smectites over time periods of 10"5–10"6 years. - Highlights: • Alkaline porewaters from cement and concrete could destabilise bentonite buffer in a repository. • Evidence utilised to examine processes over repository timescales. • Alkaline water from the Troodos ophiolite reacts with bentonite. • Waters exchange Ca for Na on bentonite, smectite reacts to form palygorskite. • Observations indicate

Minimal residual disease in breast cancer. Clinical significance

International Nuclear Information System (INIS)

Kvalheim, G.

2004-01-01

Previously we have reported our results on minimal residual disease in breast cancer. Briefly, B M-aspirates were collected from 817 patients at primary surgery. Tumor cells in B M were detected by immunocytochemistry using anticytokeratin-antibodies (A E1/ A E3). Analyses of the primary tumor included histological grading, vascular invasion and immunohistochemical detection of cerbB2, cathepsin D, p53 and ER/PgRexpression. These analyses were compared to clinical outcome. Median follow-up was 49 months. ITC were detected in 13.2% of the patients. The detection rate rose with increasing tumor size (p=0.011) and lymph node involvement (p<0.001). Systemic relapse and death from breast cancer occurred in 31.7% and 26.9% of the B M-positive versus 13.7% and 10.9% of B M-negative patients, respectively (p<0.001). Analyzing node-positive and node-negative patients separately, ITC-positivity was associated with poor prognosis in the node-positive group and in node-negative patients not receiving adjuvant therapy (T1N0). In multivariate analysis, ITC in B M was an independent prognostic factor together with N-, T-, ER/Pg R-status, histological grade and vascular invasion. Combination of several independent prognostic factors can classify subgroups of patients into excellent and high-risk prognosis groups. Like other groups we have investigated the clinical role of monitoring minimal residual disease before and after adjuvant therapy in breast cancer. One hundred and eighteen high risk stage II breast cancer patients entering the Scandinavian Study Group multicenter trial were randomized to 9 cycles of dose escalated and tailored FEC (5-flurouracil, epirubicin, cyclophosphamide) or standard FEC followed by high dose chemotherapy. B M samples at diagnosis and 6 months after completion of chemotherapy were assessed for the presence of I CT. Median observation time for patients was 68 months. ITC positivity in bone marrow was evaluated as a prognostic and predictive marker and

Six Strategies for Chemical Waste Minimization in Laboratories.

Science.gov (United States)

Matteson, Gary C.; Hadley, Cheri R.

1991-01-01

Guidelines are offered to research administrators for reducing the volume of hazardous laboratory waste. Suggestions include a chemical location inventory, a chemical reuse facility, progressive contracts with chemical suppliers, internal or external chemical recycling mechanisms, a "chemical conservation" campaign, and laboratory fees for…

INEEL Radioactive Liquid Waste Reduction Program

International Nuclear Information System (INIS)

Millet, C.B.; Tripp, J.L.; Archibald, K.E.; Lauerhauss, L.; Argyle, M.D.; Demmer, R.L.

1999-01-01

Reduction of radioactive liquid waste, much of which is Resource Conservation and Recovery Act (RCRA) listed, is a high priority at the Idaho National Technology and Engineering Center (INTEC). Major strides in the past five years have lead to significant decreases in generation and subsequent reduction in the overall cost of treatment of these wastes. In 1992, the INTEC, which is part of the Idaho National Environmental and Engineering Laboratory (INEEL), began a program to reduce the generation of radioactive liquid waste (both hazardous and non-hazardous). As part of this program, a Waste Minimization Plan was developed that detailed the various contributing waste streams, and identified methods to eliminate or reduce these waste streams. Reduction goals, which will reduce expected waste generation by 43%, were set for five years as part of this plan. The approval of the plan led to a Waste Minimization Incentive being put in place between the Department of Energy Idaho Office (DOE-ID) and the INEEL operating contractor, Lockheed Martin Idaho Technologies Company (LMITCO). This incentive is worth $5 million dollars from FY-98 through FY-02 if the waste reduction goals are met. In addition, a second plan was prepared to show a path forward to either totally eliminate all radioactive liquid waste generation at INTEC by 2005 or find alternative waste treatment paths. Historically, this waste has been sent to an evaporator system with the bottoms sent to the INTEC Tank Farm. However, this Tank Farm is not RCRA permitted for mixed wastes and a Notice of Non-compliance Consent Order gives dates of 2003 and 2012 for removal of this waste from these tanks. Therefore, alternative treatments are needed for the waste streams. This plan investigated waste elimination opportunities as well as treatment alternatives. The alternatives, and the criteria for ranking these alternatives, were identified through Value Engineering meetings with all of the waste generators. The most

Residues from waste incineration. Final report. Rev. ed.

Energy Technology Data Exchange (ETDEWEB)

Astrup, T.; Juul Pedersen, A.; Hyks, J.; Frandsen, F.J.

2010-04-15

The overall objective of the project was to improve the understanding of the formation and characteristics of residues from waste incineration. This was done focusing on the importance of the waste input and the operational conditions of the furnace. Data and results obtained from the project have been discussed in this report according to the following three overall parts: i) mass flows and element distribution, ii) flue gas/particle partitioning and corrosion/deposition aspects, and iii) residue leaching. This has been done with the intent of structuring the discussion while tacitly acknowledging that these aspects are interrelated and cannot be separated. Overall, it was found that the waste input composition had significant impact of the characteristics of the generated residues. A similar correlation between operational conditions and residue characteristics could not be observed. Consequently, the project recommend that optimization of residue quality should focus on controlling the waste input composition. The project results showed that including specific waste materials (and thereby also excluding the same materials) may have significant effects on the residue composition, residue leaching, aerosol and deposit formation.It is specifically recommended to minimize Cl in the input waste. Based on the project results, it was found that a significant potential for optimization of waste incineration exist. (Author)

Hanford Central Waste Complex: Waste Receiving and Processing Facility dangerous waste permit application

International Nuclear Information System (INIS)

1991-10-01

The Hanford Central Waste Complex is an existing and planned series of treatment, and/or disposal (TSD) unites that will centralize the management of solid waste operations at a single location on the Hanford Facility. The Complex includes two units: the WRAP Facility and the Radioactive Mixed Wastes Storage Facility (RMW Storage Facility). This Part B permit application addresses the WRAP Facility. The Facility will be a treatment and storage unit that will provide the capability to examine, sample, characterize, treat, repackage, store, and certify radioactive and/or mixed waste. Waste treated and stored will include both radioactive and/or mixed waste received from onsite and offsite sources. Certification will be designed to ensure and demonstrate compliance with waste acceptance criteria set forth by onsite disposal units and/or offsite facilities that subsequently are to receive waste from the WRAP Facility. This permit application discusses the following: facility description and general provisions; waste characterization; process information; groundwater monitoring; procedures to prevent hazards; contingency plant; personnel training; exposure information report; waste minimization plan; closure and postclosure requirements; reporting and recordkeeping; other relevant laws; certification

Sustainable construction : towards a strategic approach to construction material management for waste reduction

OpenAIRE

Abarca Guerrero, L.; Scheublin, F.J.M.; Egmond - de Wilde De Ligny, van, E.L.C.; Lambert, A.J.D.

2008-01-01

The construction sector plays a key role in shaping and developing the built environment. It also has an undisputed and significant impact on it due to the amounts of materials extracted and produced as waste. The construction industry has emphasized to recycling construction waste (CW), however, relatively less emphasis has been paid on construction waste minimization. CW reduction can be achieved through changes in design concepts, material and construction methods selection and material ma...

Hazardous waste systems analysis at Los Alamos National Laboratory

International Nuclear Information System (INIS)

Urioste, J.

1997-01-01

Los Alamos National Laboratory produces routine and non-routine hazardous waste as a by-product of mission operations. Hazardous waste commonly generated at the Laboratory includes many types of laboratory research chemicals, solvents, acids, bases, carcinogens, compressed gases, metals, and other solid waste contaminated with hazardous waste. The Los Alamos National Laboratory Environmental Stewardship Office has established a Hazardous Waste Minimization Coordinator to specifically focus on routine and non-routine RCRA, TSCA, and other administratively controlled wastes. In this process, the Waste Minimization Coordinator has developed and implemented a systems approach to define waste streams, estimate waste management costs and develop plans to implement avoidance practices, and develop projects to reduce or eliminate the waste streams at the Laboratory. The paper describes this systems approach

Municipal Solid Waste Resources

Energy Technology Data Exchange (ETDEWEB)

None

2016-06-01

Municipal solid waste (MSW) is a source of biomass material that can be utilized for bioenergy production with minimal additional inputs. MSW resources include mixed commercial and residential garbage such as yard trimmings, paper and paperboard, plastics, rubber, leather, textiles, and food wastes. Waste resources such as landfill gas, mill residues, and waste grease are already being utilized for cost-effective renewable energy generation. MSW for bioenergy also represents an opportunity to divert greater volumes of residential and commercial waste from landfills.

Mixed waste: Proceedings

International Nuclear Information System (INIS)

Moghissi, A.A.; Blauvelt, R.K.; Benda, G.A.; Rothermich, N.E.

1993-01-01

This volume contains the peer-reviewed and edited versions of papers submitted for presentation a the Second International Mixed Waste Symposium. Following the tradition of the First International Mixed Waste Symposium, these proceedings were prepared in advance of the meeting for distribution to participants. The symposium was organized by the Mixed Waste Committee of the American Society of Mechanical Engineers. The topics discussed at the symposium include: stabilization technologies, alternative treatment technologies, regulatory issues, vitrification technologies, characterization of wastes, thermal technologies, laboratory and analytical issues, waste storage and disposal, organic treatment technologies, waste minimization, packaging and transportation, treatment of mercury contaminated wastes and bioprocessing, and environmental restoration. Individual abstracts are catalogued separately for the data base

Mixed waste: Proceedings

Energy Technology Data Exchange (ETDEWEB)

Moghissi, A.A.; Blauvelt, R.K.; Benda, G.A.; Rothermich, N.E. [eds.] [Temple Univ., Philadelphia, PA (United States). Dept. of Environmental Safety and Health

1993-12-31

This volume contains the peer-reviewed and edited versions of papers submitted for presentation a the Second International Mixed Waste Symposium. Following the tradition of the First International Mixed Waste Symposium, these proceedings were prepared in advance of the meeting for distribution to participants. The symposium was organized by the Mixed Waste Committee of the American Society of Mechanical Engineers. The topics discussed at the symposium include: stabilization technologies, alternative treatment technologies, regulatory issues, vitrification technologies, characterization of wastes, thermal technologies, laboratory and analytical issues, waste storage and disposal, organic treatment technologies, waste minimization, packaging and transportation, treatment of mercury contaminated wastes and bioprocessing, and environmental restoration. Individual abstracts are catalogued separately for the data base.

Optimization of waste management by actions taken at source

International Nuclear Information System (INIS)

Strachan, N.R.; Wakerley, M.W.

1988-01-01

The purpose of this document is to collate and review information on those measures and practices adopted within nuclear facilities to optimize the management of radioactive waste at the point at which it arises. The information on which it has been based has been obtained by a review of the literature and by visits to a number of different types of facilities within the European Community. The search revealed mainly references to waste-management optimization at US LWRs, whereas the visits have tried to cover as wide a range of European facilities as practicable. There are a number of different respects in which radioactive waste can be minimized: - minimizing the amount of activity appearing in the wastes. This is best achieved by the design of process equipment; - minimizing the volume of waste with which radioactivity is associated. This is best achieved by a combination of administrative controls and equipment design; - minimizing the amount of material which for administrative or measurement reasons is considered to be radioactive. Many examples of minimization at source by means of developments in equipment and administrative controls that were encountered during our visits, or identified in the literature search, are described

Optimization of waste management by actions taken at source

International Nuclear Information System (INIS)

Strachan, N.R.; Wakerley, M.W.

1988-01-01

The purpose of this document is to collate and review information on those measures and practices adopted within nuclear facilities to optimize the management of radioactive waste at the point of arising. The information on which it has been based has been obtained by literature review and by visits to a number of different types of facilities within the European Community. The search revealed mainly references to waste management optimization at US LWRs, whereas the visits have tried to cover as wide a range of European facilities as practicable. There are a number of different respects in which radioactive waste can be minimized: minimizing the amount of activity appearing in the wastes. This is best achieved by the design of process equipment; minimizing the volume of waste with which radioactivity is associated. This is best achieved by a combination of administrative controls and equipment design; minimizing the amount of material which for administrative or measurement reasons is considered to be radioactive. Many examples of minimization at source by means of equipment developments and administrative controls that were encountered during our visits or identified in the literature search are described. (author)

Strategy for managing mixed waste at a plant site

International Nuclear Information System (INIS)

Fentiman, A.

1991-01-01

No waste disposal site is currently accepting mixed waste, but facilities across the country continue to generate it. The waste manager at each site is faced with two problems: how to manage the mixed waste already on-site and how to minimize the amount of new waste generated. A strategy has been developed to address each problem. A key element of the strategy is a building-by-building survey of the site. The survey provides information on how and where mixed waste is generated and stored. This paper describes a method for planning and conducting a site-wide mixed-waste survey. It then outlines approaches to managing existing mixed waste and to minimizing mixed-waste generation using information from the survey

The Savannah River Site Waste Inventory Management Program

International Nuclear Information System (INIS)

Griffith, J.M.; Holmes, B.R.

1995-01-01

Each hazardous and radioactive waste generator that delivers waste to Savannah River Site (SRS) treatment, storage and disposal (TSD) facilities is required to implement a waste certification plan. The waste certification process ensures that waste has been properly identified, characterized, segregated, packaged, and shipped according to the receiving facilities waste acceptance criteria. In order to comply with the rigid acceptance criteria, the Reactor Division developed and implemented the Waste Inventory Management Program (WIMP) to track the generation and disposal of low level radioactive waste. The WIMP system is a relational database with integrated barcode technology designed to track the inventory radioactive waste. During the development of the WIMP several waste minimization tools were incorporated into the design of the program. The inclusion of waste minimization tools as part of the WIMP has resulted in a 40% increase in the amount of waste designated as compactible and an overall volume reduction of 5,000 cu-ft

Los Alamos Waste Management Cost Estimation Model

International Nuclear Information System (INIS)

Matysiak, L.M.; Burns, M.L.

1994-03-01

This final report completes the Los Alamos Waste Management Cost Estimation Project, and includes the documentation of the waste management processes at Los Alamos National Laboratory (LANL) for hazardous, mixed, low-level radioactive solid and transuranic waste, development of the cost estimation model and a user reference manual. The ultimate goal of this effort was to develop an estimate of the life cycle costs for the aforementioned waste types. The Cost Estimation Model is a tool that can be used to calculate the costs of waste management at LANL for the aforementioned waste types, under several different scenarios. Each waste category at LANL is managed in a separate fashion, according to Department of Energy requirements and state and federal regulations. The cost of the waste management process for each waste category has not previously been well documented. In particular, the costs associated with the handling, treatment and storage of the waste have not been well understood. It is anticipated that greater knowledge of these costs will encourage waste generators at the Laboratory to apply waste minimization techniques to current operations. Expected benefits of waste minimization are a reduction in waste volume, decrease in liability and lower waste management costs

Food waste and the food-energy-water nexus: A review of food waste management alternatives.

Science.gov (United States)

Kibler, Kelly M; Reinhart, Debra; Hawkins, Christopher; Motlagh, Amir Mohaghegh; Wright, James

2018-04-01

Throughout the world, much food produced is wasted. The resource impact of producing wasted food is substantial; however, little is known about the energy and water consumed in managing food waste after it has been disposed. Herein, we characterize food waste within the Food-Energy-Water (FEW) nexus and parse the differential FEW effects of producing uneaten food and managing food loss and waste. We find that various food waste management options, such as waste prevention, landfilling, composting, anaerobic digestion, and incineration, present variable pathways for FEW impacts and opportunities. Furthermore, comprehensive sustainable management of food waste will involve varied mechanisms and actors at multiple levels of governance and at the level of individual consumers. To address the complex food waste problem, we therefore propose a "food-waste-systems" approach to optimize resources within the FEW nexus. Such a framework may be applied to devise strategies that, for instance, minimize the amount of edible food that is wasted, foster efficient use of energy and water in the food production process, and simultaneously reduce pollution externalities and create opportunities from recycled energy and nutrients. Characterization of FEW nexus impacts of wasted food, including descriptions of dynamic feedback behaviors, presents a significant research gap and a priority for future work. Large-scale decision making requires more complete understanding of food waste and its management within the FEW nexus, particularly regarding post-disposal impacts related to water. Copyright © 2018 Elsevier Ltd. All rights reserved.

Applicability of molten salt oxidation to the destruction of actinide-contaminated wastes

International Nuclear Information System (INIS)

West, M.H.; Garcia, E.; Griego, W.J.; Court, D.B.; Rodriguez, L.

1992-01-01

A 1989 ban on incineration in the state of New Mexico caused cessation of actinide-contaminated cheesecloth, paper, and wood incineration within the Plutonium Facility (TA-55) at Los Alamos National Laboratory. Subsequently, plastic wipes were substituted for cheesecloth in the cleaning of glovebox interiors. However, waste minimization is not achieved by these measures since the wipes are discarded as Waste Isolation Pilot Plant certifiable wastes. After the ban was instituted, thermal decomposition of cheesecloth under argon at elevated temperature was examined and found satisfactory although scale of operation and speed were inferior to incineration. In 1991, the ban on incineration was lifted in New Mexico but Alamos has not chosen to pursue renewal of incineration at the Plutonium Facility. This paper reports that Los Alamos is looking from alternatives to incineration and thermal decomposition which are compatible with molten salt processing technology, historically a strength in actinide research at the Laboratory. Also, the technology must significantly reduce the volume of the waste upon treatment, i.e. waste minimization. Molten salt oxidation (MSO) has the promise of such a technology

Waste reduction program at Oak Ridge National Laboratory during CY 1989

Energy Technology Data Exchange (ETDEWEB)

Schultz, R.M.

1990-05-01

Hazardous, radioactive, and mixed wastes are generated at Oak Ridge National Laboratory (ORNL). The State of Tennessee has requested that ORNL organize the waste streams into approximately 30 generic categories for the CY 1989 report so the information is more manageable. The wide diversity of waste complicates both management and compliance with reporting requirements that are designed to apply to production facilities. In recent years, increased effort has been devoted to the minimization of hazardous and radioactive wastes at ORNL. Policy statements supporting such efforts have been issued by both Martin Marietta Energy Systems, Inc., and ORNL management. Motivation is found in federal regulations, DOE policies and guidelines, increased costs and liabilities associated with the management of wastes, and limited disposal options and facility capacities. ORNL's waste minimization efforts have achieved some success. However, because of the diversity and predominantly nonroutine nature of ORNL's containerized wastes, goals for their reduction are difficult to establish. Efforts continue to establish goals that account separately for wastes generated from laboratory cleanouts, to avoid a waste minimization penalty'' for this good housekeeping practice. Generator evaluations to prioritize hazardous waste streams for waste minimization opportunities are planned for FY 1990. These are important first steps to enable the waste reduction program to assign realistic goals. 22 refs., 13 figs., 10 tabs.

Waste reduction program at Oak Ridge National Laboratory during CY 1989

International Nuclear Information System (INIS)

Schultz, R.M.

1990-05-01

Hazardous, radioactive, and mixed wastes are generated at Oak Ridge National Laboratory (ORNL). The State of Tennessee has requested that ORNL organize the waste streams into approximately 30 generic categories for the CY 1989 report so the information is more manageable. The wide diversity of waste complicates both management and compliance with reporting requirements that are designed to apply to production facilities. In recent years, increased effort has been devoted to the minimization of hazardous and radioactive wastes at ORNL. Policy statements supporting such efforts have been issued by both Martin Marietta Energy Systems, Inc., and ORNL management. Motivation is found in federal regulations, DOE policies and guidelines, increased costs and liabilities associated with the management of wastes, and limited disposal options and facility capacities. ORNL's waste minimization efforts have achieved some success. However, because of the diversity and predominantly nonroutine nature of ORNL's containerized wastes, goals for their reduction are difficult to establish. Efforts continue to establish goals that account separately for wastes generated from laboratory cleanouts, to avoid a waste minimization ''penalty'' for this good housekeeping practice. Generator evaluations to prioritize hazardous waste streams for waste minimization opportunities are planned for FY 1990. These are important first steps to enable the waste reduction program to assign realistic goals. 22 refs., 13 figs., 10 tabs

Utilizing a 'systems' approach to improve the management of waste from healthcare facilities: best practice case studies from England and Wales.

Science.gov (United States)

Tudor, Terry L; Woolridge, Anne C; Bates, Margaret P; Phillips, Paul S; Butler, Sharon; Jones, Keith

2008-06-01

Changes in environmental legislation and standards governing healthcare waste, such as the Hazardous Waste Regulations are expected to have a significant impact on healthcare waste quantities and costs in England and Wales. This paper presents findings from two award winning case study organizations, the Cardiff and Vale NHS Trust and the Cornwall NHS Trust on 'systems' they have employed for minimizing waste. The results suggest the need for the development and implementation of a holistic range of systems in order to develop best practice, including waste minimization strategies, key performance indicators, and staff training and awareness. The implications for the sharing of best practice from the two case studies are also discussed.

Zone Freezing Study for Pyrochemical Process Waste Minimization

Energy Technology Data Exchange (ETDEWEB)

Ammon Williams

2012-05-01

Pyroprocessing technology is a non-aqueous separation process for treatment of used nuclear fuel. At the heart of pyroprocessing lies the electrorefiner, which electrochemically dissolves uranium from the used fuel at the anode and deposits it onto a cathode. During this operation, sodium, transuranics, and fission product chlorides accumulate in the electrolyte salt (LiCl-KCl). These contaminates change the characteristics of the salt overtime and as a result, large volumes of contaminated salt are being removed, reprocessed and stored as radioactive waste. To reduce the storage volumes and improve recycling process for cost minimization, a salt purification method called zone freezing has been proposed at Korea Atomic Energy Research Institute (KAERI). Zone freezing is melt crystallization process similar to the vertical Bridgeman method. In this process, the eutectic salt is slowly cooled axially from top to bottom. As solidification occurs, the fission products are rejected from the solid interface and forced into the liquid phase. The resulting product is a grown crystal with the bulk of the fission products near the bottom of the salt ingot, where they can be easily be sectioned and removed. Despite successful feasibility report from KAERI on this process, there were many unexplored parameters to help understanding and improving its operational routines. Thus, this becomes the main motivation of this proposed study. The majority of this work has been focused on the CsCl-LiCl-KCl ternary salt. CeCl3-LiCl-KCl was also investigated to check whether or not this process is feasible for the trivalent species—surrogate for rare-earths and transuranics. For the main part of the work, several parameters were varied, they are: (1) the retort advancement rate—1.8, 3.2, and 5.0 mm/hr, (2) the crucible lid configurations—lid versus no-lid, (3) the amount or size of mixture—50 and 400 g, (4) the composition of CsCl in the salt—1, 3, and 5 wt%, and (5) the

Waste minimization through high-pressure microwave digestion of soils for gross α/β analyses

International Nuclear Information System (INIS)

Yaeger, J.S.; Smith, L.L.

1995-04-01

As a result of the U.S. Department of Energy's (DOE) environmental restoration and waste management activities, laboratories receive numerous analytical requests for gross α/β analyses. Traditional sample preparation methods for gross α/β analysis of environmental and mixed waste samples require repetitive leaching, which is time consuming and generates large volumes of secondary wastes. An alternative to leaching is microwave digestion. In the past. microwave technology has had limited application in the radiochemical laboratory because of restrictions on sample size resulting from vessel pressure limitations. However, new microwave vessel designs allow for pressures on the order of 11 MPa (1500 psi). A procedure is described in which microwave digestion is used to prepare environmental soil samples for gross α/β analysis. Results indicate that the described procedure meets performance requirements for several soil types and is equivalent to traditional digestion techniques. No statistical differences at the 95% confidence interval exist between the measurement on samples prepared from the hot plate and microwave digestion procedures for those soils tested. Moreover, microwave digestion allows samples to be prepared in a fraction of the time with significantly less acid and with lower potential of cross-contamination. In comparison to the traditional hot plate method, the waste volumes required for the microwave procedure are a factor of 10 lower, while the analyst time for sample processing is at least a factor of three lower

Environmental evaluation of waste management scenarios - significance of the boundaries

NARCIS (Netherlands)

Ghinea, C.; Petraru, M.; Bressers, Johannes T.A.; Gavrilescu, M.

2012-01-01

Life cycle concept was applied to analyse and assess some municipal solid waste (MSW) management scenarios in terms of environmental impacts, particularised for Iasi city, Romania, where approximately 380 kg/cap/yr of waste are generated. Currently, the management processes include temporary

Low-level radioactive wastes in subsurface soils

International Nuclear Information System (INIS)

Francis, A.J.

1985-01-01

Low-level radioactive wastes will continue to be buried in shallow-land waste disposal sites. Several of the burial sites have been closed because of the problems that developed as a result of poor site characteristics, types of waste buried, and a number of other environmental factors. Some of the problems encountered can be traced to the activities of microorganisms. These include microbial degradation of waste forms resulting in trench cover subsidence, production of radioactive gases, and production of microbial metabolites capable of complexation, solubilization, and bioaccumulation of radionuclides. Improvements in disposal technology are being developed to minimize these problems. These include waste segregation, waste pretreatment, incineration, and solidification. Microorganisms are also known to enhance and inhibit the movement of metals. Little is known about the role of autotrophic microbial transformations of radionuclides. Such microbial processes may be significant in light of improved disposal procedures, which may result in reductions in the organic content of the waste disposed of at shallow-land sites. 102 references, 5 figures, 19 tables

A comparative assessment of alternative waste management procedures for selected reprocessing wastes

International Nuclear Information System (INIS)

Hickford, G.E.; Plews, M.J.

1983-07-01

This report, which has been prepared by Associated Nuclear Services for the Department of the Environment, presents the results of a study and comparative assessment of management procedures for low and intermediate level solid waste streams arising from current and future fuel reprocessing operations on the Sellafield site. The characteristics and origins of the wastes under study are discussed and a reference waste inventory is presented, based on published information. Waste management strategy in the UK and its implications for waste conditioning, packaging and disposal are discussed. Wastes currently arising which are not suitable for Drigg burial or sea dumping are stored in an untreated form. Work is in hand to provide additional and improved disposal facilities which will accommodate all the waste streams under study. For each waste stream viable procedures are identified for further assessment. The procedures comprise a series of on-site operations-recovery from storage, pre-treatment, treatment, encapsulation, and packaging, prior to storage or disposal of the conditioned waste form. Assessments and comparisons of each procedure for each waste are presented. These address various process, operational, economic, radiological and general safety factors. The results are presented in a series of tables with supporting text. For the majority of wastes direct encapsulation with minimal treatment appears to be a viable procedure. Occupational exposure and general safety are not identified as significant factors governing the choice of procedures. The conditioned wastes meet the general requirements for safe handling during storage and transportation. The less active wastes suitable for disposal by currently available routes meet the appropriate disposal criteria. It is not possible to consider in detail the suitability for disposal of the more active wastes for which disposal facilities are not yet available. (Author)

Risk management of onsite transportation of nuclear waste

International Nuclear Information System (INIS)

Field, J.G.; Wang, O.S.; Mercado, J.E.

1993-01-01

The United States Department of Energy (DOE) Hanford Site recently has undergone a significant change in mission. The focus of operations has shifted from plutonium production to environmental restoration. This transition has caused a substantial increase in quantities of nuclear waste and other hazardous materials packaged and transported onsite. In response to the escalating transportation activity, Westinghouse Hanford Company (Westinghouse Hanford), the Hanford Site operations and engineering contractor, is proposing an integrated risk assessment methodology and risk management strategy to enhance the safety of onsite packaging and transportation operations involving nuclear waste. The proposed methodology consists of three integral parts: risk assessment, risk acceptance criteria, and risk minimization. The purpose of the methodology is to ensure that the risk for each ongoing transportation activity is acceptable and to minimize the overall risk for current and future onsite operations. (authors). 2 figs., 6 refs

Risk management of onsite transportation of nuclear waste

International Nuclear Information System (INIS)

Field, J.G.; Wang, O.S.; Mercado, J.E.

1993-03-01

The United States Department of Energy (DOE) Hanford Site recently has undergone a significant change in mission. The focus of operations has shifted from plutonium production to environmental restoration. This transition has caused a substantial increase in quantities of nuclear waste and other hazardous materials packaged and transported onsite. In response to the escalating transportation activity, Westinghouse Hanford Company (Westinghouse Hanford), the Hanford Site operations and engineering contractor, is proposing an integrated risk assessment methodology and risk management strategy to enhance the safety of onsite packaging and transportation operations involving nuclear waste. The proposed methodology consists of three integral parts: risk assessment, risk acceptance criteria, and risk minimization. The purpose of the methodology is to ensure that the risk for each ongoing transportation activity is acceptable and to minimize the overall risk for current and future onsite operations

Training waste generators: The first responder in proper waste management

International Nuclear Information System (INIS)

Jones, E.

1989-01-01

Dealing with waste effectively requires a ''cradle to grave'' approach to waste management. The first step in that chain of custody is the waste generator. The waste generator plays the key role in the correct identification, packaging, and disposal of waste. The Technical Resources and Training Section at the Oak Ridge National Laboratory (ORNL) has developed several short training programs for waste generators. This training presents a consistent approach to proper handling of waste within the ORNL waste management system. This training has been developed for generators of solid low-level radioactive waste, hazardous and mixed waste, and transuranic waste. In addition to the above, a Waste Minimization training program has been developed for use by all organizations at ORNL who generate any type of hazardous waste. These training programs represent a combined effort of the training staff and the technical staff to assure that all ORNL staff accept their responsibility for handling all types of radioactive and hazardous wastes correctly from its generation to its disposal. 4 refs

Waste minimization activities in Toyota Motor Corporation; Haikibutsu teigen eno torikumi jokyo

Energy Technology Data Exchange (ETDEWEB)

Taguchi, S.; Yamamoto, N.; Kurai, H. [Toyota Motor Corp., Aichi (Japan)

1998-07-01

Toyota`s waste reduction efforts based on a drive for dealing with the source of waste generation are introduced. For the propulsion of the policy for dealing directly with the origin of waste, it is necessary to convert the existing manufacturing processes that give high priority to product quality and low production cost into environmental impact reduction oriented processes. In particular, conversion of materials into those that are easier to recycle, technology for reducing defective products, technology for the completion of recycling within the process involved, and the simplification of all the processes are mentioned. For the cleaning job in the machining process, a detergent enhanced in oil/water separating capability is developed, and this prolongs doubly the detergent replacement period and decreases the waste liquid to a 1/4 or less of what the conventional method produces. For the handling of foundry sand that is yielded in great quantities, a flow classification system is developed to replace the conventional gravitational classifier, and the reusable coarse-grain sand in the collected dust which occupies approximately 70% of the whole waste is now recovered for reuse. In the vehicle body coating process, a newly-developed robot arm type coating system is developed, which halves the coating waste. 2 refs., 9 figs., 1 tab.

Uranium and thorium cycles for sodium fast reactors: Neutronic aspects and associated wastes

International Nuclear Information System (INIS)

Brizi, J.

2010-10-01

Sodium fast reactors (SFR-Na) with uranium 238/plutonium 239(U/Pu) cycle, its technical feasibility has already proven, allow to overcome the problem of natural uranium resources in achieving the regeneration of the fuel fissile element. In addition, a waste management can be performed to reduce the radiotoxicity of actinides produced by the reactor in transmuting the AM in the core (homogeneous transmutation). Another alternative to minimize waste is to use another couple fertile-fissile: the thorium 232 and the uranium 233 (Th/U). The comparison is performed on neutronic and safety aspects and on waste production, in using an evolutive Monte Carlo. Although one does not disclose real clear advantages concerning the radiotoxicity of wastes for a particular cycle, the Th/U cycle reduces the radiotoxicity during periods when it is the highest. The homogeneous transmutation minimizes significantly for both cycles, radiotoxicity of wastes, with different factors depending on the considered time period. However, it is done to the detriment of an important increase of AM in the core. If we consider the nuclear stop, the inventory of the reactor core becomes a waste. The gain provided by the transmutation, taking into account both the core and accumulated waste radio-toxicities, will be quantified, and shows the transmutation does not provide a significant gain if the burning of main fissile elements is not considered when the nuclear is stopped. (author)

Proceedings of waste stream minimization and utilization innovative concepts: An experimental technology exchange. Volume 1, Industrial solid waste processing municipal waste reduction/recycling

Energy Technology Data Exchange (ETDEWEB)

Lee, V.E. [ed.; Watts, R.L.

1993-04-01

This two-volume proceedings summarizes the results of fifteen innovations that were funded through the US Department of Energy`s Innovative Concept Program. The fifteen innovations were presented at the sixth Innovative Concepts Fair, held in Austin, Texas, on April 22--23, 1993. The concepts in this year`s fair address innovations that can substantially reduce or use waste streams. Each paper describes the need for the proposed concept, the concept being proposed, and the concept`s economics and market potential, key experimental results, and future development needs. The papers are divided into two volumes: Volume 1 addresses innovations for industrial solid waste processing and municipal waste reduction/recycling, and Volume 2 addresses industrial liquid waste processing and industrial gaseous waste processing. Selected papers have been indexed separately for inclusion in the Energy Science and Technology Database.

Innovative technologies for the treatment of hazardous and mixed wastes

International Nuclear Information System (INIS)

Eyman, L.D.; Anderson, T.D.

1988-01-01

The treatment, storage, and disposal of hazardous and mixed wastes incur significant costs for Department of Energy (DOE) installations. These wastes must be managed under strict environmental controls and regulations to prevent the possibility of migration of hazardous materials to the biosphere. Through the Hazardous Waste Remedial Actions Program, the DOE is seeking to develop innovative ways of improving current treatment technologies to eliminate the hazardous components of wastes, reduce waste management costs, and minimize the volume requiring disposal as hazardous or mixed waste. Sponsored projects progress from research and development to field demonstration. Among the innovative technologies under development are supercritical water oxidation of hazardous chemicals, microwave-assisted destruction of chlorinated hydrocarbons, paramagnetic separation of metals from waste, detoxification and reclamation of waste acid, nitrate destruction through calcination, treatment/disposal of reactive metals, and methodologies for encapsulation. Technologies at a demonstration phase include detoxification of mixed waste sludge, microbial degradation of polychlorinated biphenyls in soil, and the remediation process for a hydrocarbon spill. 14 refs

Significant progress towards development of the low-level radioactive waste disposal facility in Illinois

International Nuclear Information System (INIS)

Klebe, M.; Henry, T.L.; Corpstein, P.

1996-01-01

Development of disposal sites for low-level radioactive waste is a complicated legal, regulatory and public sector process. Development of the low-level radioactive waste disposal facility to support generators in Illinois and Kentucky is well under way. Significant progress has been made to re-engineer the siting development process capitalizing on prior lessons learned and a recommitment from Illinois state leadership assuring the future success of the program. Comparisons of why this new process will succeed are the major focus of this paper. Specific changes in approach from the previous process including changes in the Illinois Management Act (Management Act), creation of the Illinois Low-Level Radioactive Waste Siting Task Group (Task Group), new roles for the Illinois State Geologic Survey and Illinois State Water Survey (Scientific Surveys) and the Illinois Department of Nuclear Safety (IDNS), a new contractor reliance approach and increased confidence on the open-quote science close-quote are the major contrasts between the previous process and the new process currently underway

Comparison between radioactive waste management and the exposure of workers

International Nuclear Information System (INIS)

Pena, G.P.; Santos, J.S.; González, J.A.; Pássaro, B.M.; Videira, H.S.; Lopes, A.B.; Buchpiguel, C.A.; Guimarães, M.I.C.C.

2015-01-01

Depending on how the radioactive waste is managed it can become an additional source of exposure to the worker. In order to minimize this exposure the amount of radioactive waste generated by a nuclear medicine center was analyzed, quantified, qualified and compared with the doses obtained by personal dosimetry in the Nuclear Medicine Service of InRad HCFMUSP. The greatest quantity of radioactive waste produced was of "9"9"mTc. Approximately 90% of the solid waste was non-compactable, such as needles and others, and the remaining 10% were of compactable waste (gauze, gloves and other). Among the years there has been a significant variation in the amount of waste, which is directly connected with the quantity of exams performed. The medium dose value observed was of 0.6 mSv per month for all the workers, including radiopharmacists, nurses and physicists (dosimeters positioned in thorax) and 1.6 mSv in wrist dosimeters. We observed that months with greater amount of waste coincided with months of higher doses. However, this increase was not significant and was not proportional due to optimization in handling the waste. (authors)

A Mathematical Model for the Industrial Hazardous Waste Location-Routing Problem

Directory of Open Access Journals (Sweden)

Omid Boyer

2013-01-01

Full Text Available Technology progress is a cause of industrial hazardous wastes increasing in the whole world . Management of hazardous waste is a significant issue due to the imposed risk on environment and human life. This risk can be a result of location of undesirable facilities and also routing hazardous waste. In this paper a biobjective mixed integer programing model for location-routing industrial hazardous waste with two objectives is developed. First objective is total cost minimization including transportation cost, operation cost, initial investment cost, and cost saving from selling recycled waste. Second objective is minimization of transportation risk. Risk of population exposure within bandwidth along route is used to measure transportation risk. This model can help decision makers to locate treatment, recycling, and disposal centers simultaneously and also to route waste between these facilities considering risk and cost criteria. The results of the solved problem prove conflict between two objectives. Hence, it is possible to decrease the cost value by marginally increasing the transportation risk value and vice versa. A weighted sum method is utilized to combine two objectives function into one objective function. To solve the problem GAMS software with CPLEX solver is used. The problem is applied in Markazi province in Iran.

The environmental impact of mine wastes - roles of microorganisms and their significance in treatment of mine wastes

International Nuclear Information System (INIS)

Ledin, M.; Pedersen, K.

1996-01-01

Mine wastes constitute a potential source of contamination to the environment, as heavy metals and acid are released in large amounts. A great variety of microorganisms has been found in mine wastes and microbiological processes are usually responsible for the environmental hazard created by mine wastes. However, microorganisms can also be used to retard the adverse impact of mine wastes on the environment. Conventionally, the mine drainage as well as the waste itself can be treated with alkali to increase pH and precipitate metals. The main drawback of this method is that it has to be continuously repeated to be fully effective. There may also be negative effects on beneficial microorganisms. Several other treatment methods have been developed to stop weathering processes thereby reducing the environmental impact of mine wastes. The other main approach is to treat the drainage water. Various methods aim at using microorganisms for this in natural or engineered systems. Recently, much interest has been focused on the use of natural or artificial wetlands for treatment. In general, the activity of microorganisms is neglected in the design of mine waste treatment systems, and the treatments are created merely from a technical point of view. This can result in situations where unexpected microbial processes take over, and, in the worst scenario, the overall effect is opposite to the desired

A mathematical model for the municipal solid waste location-routing problem with intermediate transfer stations

Directory of Open Access Journals (Sweden)

Hossein Asefi

2015-09-01

Full Text Available Municipal solid waste management is one of the challenging issues in mega cities due to various interrelated factors such as operational costs and environmental concerns. Cost as one of the most significant constraints of municipal solid waste management can be effectively economized by efficient planning approaches. Considering diverse waste types in an integrated municipal solid waste system, a mathematical model of the location-routing problem is formulated and solved in this study in order to minimize the total cost of transportation and facility establishment.

Waste audit pada industri penyamakan kulit

Directory of Open Access Journals (Sweden)

Prayitno Prayitno

1999-07-01

Full Text Available Waste audit is new environmental activities. to the Indonesia public and the large part of industrial community it is one of the environmental audit activities. Waste audit aims to identify whether the waste that by the industry waste so that metods for minimizing the waste can be found. In the leather tanning industry wasted audit is performend for every step pg the process, started from the raw material strage to the fishing ptocess.

Significant reduction in blood loss in patients undergoing minimal extracorporeal circulation

NARCIS (Netherlands)

Gerritsen, W. B.; van Boven, W. J.; Smelt, M.; Morshuis, W. J.; van Dongen, H. P.; Haas, F. J.; Aarts, L. P.

2006-01-01

Several recent studies have shown differences in blood loss and allogeneic transfusion requirements between on-pump and off-pump coronary artery bypass grafting (CABG). Recently a new concept, the mini-extracorporeal circulation, was introduced to minimize the side effects of extracorporeal

Predisposal Radioactive Waste Management

International Nuclear Information System (INIS)

2014-01-01

Recognition of the importance of the safe management of radioactive waste means that, over the years, many well-established and effective techniques have been developed, and the nuclear industry and governments have gained considerable experience in this field. Minimization of waste is a fundamental principle underpinning the design and operation of all nuclear operations, together with waste reuse and recycling. For the remaining radioactive waste that will be produced, it is essential that there is a well defined plan (called a waste treatment path) to ensure the safe management and ultimately the safe disposal of radioactive waste so as to guarantee the sustainable long term deployment of nuclear technologies

The exemption of regulatory control for the management of low level radioactive wastes

International Nuclear Information System (INIS)

Ortiz, M.T.; Carboneras, P.

1993-01-01

A high number of wastes produced in different fields of science and technology, as well as nuclear power plants, contain a significant volume of byproducts contaminated with radioisotopes, having a very low radioactive level. This kind of wastes might be managed as ordinary wastes by conventional methods or even reused. In order to carry out this procedure, a new regulation exempting these products from the regulatory control normatives would be necessary. This paper analyzes the big advantages of introducing these exemptions (costs recycling, radioactive wastes minimization) and how they follow the recommendations of ICRP, IAEA, EC and NRC

Prospects of nuclear waste management and radioactive waste management

International Nuclear Information System (INIS)

Koprda, V.

2015-01-01

The policy of radioactive waste management in the Slovak Republic is based on the principles defined by law on the National Nuclear Fund (NJF) and sets basic objectives: 1 Safe and reliable nuclear decommissioning; 2 The minimization of radioactive waste; 3. Selection of a suitable fuel cycle; 4 Safe storage of radioactive waste (RAW) 5 Security chain management of radioactive waste and spent nuclear fuel (SNF); 6 Nuclear safety; 7 The application of a graduated approach; 8 Respect of the principle 'a polluter pays'; 9 Objective decision-making process; 10 Responsibility. In connection with the above objectives, it appears necessary to build required facilities that are listed in this article.

Certification Plan, low-level waste Hazardous Waste Handling Facility

International Nuclear Information System (INIS)

Albert, R.

1992-01-01

The purpose of this plan is to describe the organization and methodology for the certification of low-level radioactive waste (LLW) handled in the Hazardous Waste Handling Facility (HWHF) at Lawrence Berkeley Laboratory (LBL). This plan also incorporates the applicable elements of waste reduction, which include both up-front minimization and end-product treatment to reduce the volume and toxicity of the waste; segregation of the waste as it applies to certification; an executive summary of the Waste Management Quality Assurance Implementing Management Plan (QAIMP) for the HWHF and a list of the current and planned implementing procedures used in waste certification. This plan provides guidance from the HWHF to waste generators, waste handlers, and the Waste Certification Specialist to enable them to conduct their activities and carry out their responsibilities in a manner that complies with the requirements of WHC-WAC. Waste generators have the primary responsibility for the proper characterization of LLW. The Waste Certification Specialist verifies and certifies that LBL LLW is characterized, handled, and shipped in accordance with the requirements of WHC-WAC. Certification is the governing process in which LBL personnel conduct their waste generating and waste handling activities in such a manner that the Waste Certification Specialist can verify that the requirements of WHC-WAC are met

6th international solid wastes congress and exhibition

International Nuclear Information System (INIS)

Ategrus

1992-01-01

Proceedings of the sixth International Solid Wastes Congress and exhibition held in Madrid the dates June 14-19, 1992, and organized by ISWA. It sumps up 3 volumes dealing with Environmental Aspects, Administrative Aspects, Waste treatment Technologies, Waste Minimization, Land disposal and Hazardous Wastes

Standard data report. 1997 annual report on waste generation and waste minimization progress

International Nuclear Information System (INIS)

Wilburn, D.

1998-01-01

The Laboratory's central mission of Reducing the Global Nuclear Danger supports core competencies that enable the Laboratory to contribute to defense, civilian, and industrial needs. In turn, the intellectual challenges of civilian and industrial problems strengthen and help support the core competencies required for the national security mission. The ability to do great science underpins all of the applied work. There are five core competencies which support this mission: (1) Stockpile Stewardship ensures the US has safe, secure and reliable nuclear weapons; (2) Stockpile Management provides capabilities ranging from dismantling to remanufacturing of the enduring stockpile; (3) Nuclear Materials Management ensures the availability and safe disposition of plutonium, highly enriched uranium, and tritium; (4) Nonproliferation and Counterproliferation help to deter, detect, and respond to the proliferation of weapons of mass destruction; and (5) Environmental Stewardship provides for the remediation and reduction of wastes from the nuclear weapons complex. This report contains data on volumes of waste generated as part of routine and cleanup/stabilization activities of the lab

Radiolytic gas generation from cement-based waste hosts for DOE low-level radioactive wastes

International Nuclear Information System (INIS)

Dole, L.R.; Friedman, H.A.

1986-01-01

Using cement-based immobilization binders with simulated radioactive waste containing sulfate, nitrate, nitrite, phosphate, and fluoride anions, the gamma- and alpha-radiolytic gas generation factors (G/sub t/, molecules/100 eV) and gas compositions were measured on specimens of cured grouts. These tests studied the effects of; (1) waste composition; (2) the sample surface-to-volume ratio; (3) the waste slurry particle size; and (4) the water content of the waste host formula. The radiolysis test vessels were designed to minimize the ''dead'' volume and to simulate the configuration of waste packages

Solid low level waste management guidelines

International Nuclear Information System (INIS)

Saunders, P.

1995-01-01

In the 1980's the nuclear industry began focusing a great deal of attention on minimizing the volume of low level radioactive waste (LLW) that required disposal. This was driven by several factors including rising disposal costs, increased regulatory pressures, and increased pressure from other organizations such as INPO. In the 1990's most utilities are faced with intense competition in the electrical generation market. The survival of a utility is based on their ability to produce electricity by the most efficient and economical means available. Waste management related costs are a substantial portion of most utilities O ampersand M budgets. Disposal site access denial continues to be a major factor in waste management program decision, and the pressures to minimize waste volumes from outside organizations is greater than ever

Accelerator Production of Tritium Waste Characterization and Certification Challenges

International Nuclear Information System (INIS)

Ades, M.J.; England, J.L.; Nowacki, P.L.; Hane, R.; Tempel, K.L.; Pitcher, E.; Cohen, H.S.

1998-06-01

This paper summaries the processes and methods APT used for the identification and classification of the waste streams, the characterization and certification of the waste streams, and waste minimization

Waste. The political significance of the city’s suppressed other

OpenAIRE

Chrysanthe Constantinou

2015-01-01

MBeneath the city’s achievement as a grand machine of accumulation of matter, in invisibility lies the vast and vague sphere of waste accumulation. In invisibility, a huge network of waste flows is possibly rewriting economies as we know them, reproducing life conditions driven by the politics of wealth. In this parallel territory, recycling is a big business for the few.

Westinghouse integrated cementation facility. Smart process automation minimizing secondary waste

International Nuclear Information System (INIS)

Fehrmann, H.; Jacobs, T.; Aign, J.

2015-01-01

The Westinghouse Cementation Facility described in this paper is an example for a typical standardized turnkey project in the area of waste management. The facility is able to handle NPP waste such as evaporator concentrates, spent resins and filter cartridges. The facility scope covers all equipment required for a fully integrated system including all required auxiliary equipment for hydraulic, pneumatic and electric control system. The control system is based on actual PLC technology and the process is highly automated. The equipment is designed to be remotely operated, under radiation exposure conditions. 4 cementation facilities have been built for new CPR-1000 nuclear power stations in China

Disposal of Rocky Flats residues as waste

International Nuclear Information System (INIS)

Dustin, D.F.; Sendelweck, V.S.

1993-01-01

Work is underway at the Rocky Flats Plant to evaluate alternatives for the removal of a large inventory of plutonium-contaminated residues from the plant. One alternative under consideration is to package the residues as transuranic wastes for ultimate shipment to the Waste Isolation Pilot Plant. Current waste acceptance criteria and transportation regulations require that approximately 1000 cubic yards of residues be repackaged to produce over 20,000 cubic yards of WIPP certified waste. The major regulatory drivers leading to this increase in waste volume are the fissile gram equivalent, surface radiation dose rate, and thermal power limits. In the interest of waste minimization, analyses have been conducted to determine, for each residue type, the controlling criterion leading to the volume increase, the impact of relaxing that criterion on subsequent waste volume, and the means by which rules changes may be implemented. The results of this study have identified the most appropriate changes to be proposed in regulatory requirements in order to minimize the costs of disposing of Rocky Flats residues as transuranic wastes

Pollution prevention at the Kansas City Division through process waste assessments

International Nuclear Information System (INIS)

Pemberton, S.E.; Gentile, C.C.

1992-01-01

Allied-Signal Inc., Kansas City Division (KCD) is committed to the hazardous waste minimization requirements set forth under RCRA as amended by the Pollution Prevention Act and DOE Order 5400.1. To assure compliance with these regulations, the KCD has developed a comprehensive Pollution Prevention Program which focuses on the elimination or minimization of all material releases to all environmental media. The ownership of waste minimization is given to all of the waste generators through Departmental Pollution Prevention Plans. These plans include tools to achieve the waste minimization goals. One of these tools is the process waste assessment (PWA). A PWA is a planned procedure with the objective of identifying opportunities and methods to reduce or eliminate waste. A material balance is performed around a specific process which qualifies and quantifies the materials entering and exiting the process. These materials are further defined to the hazardous component level. The exiting materials are separated into what goes into the product, sent to waste management, and what is released to the air (fugitive or point source). Next, opportunities are identified and evaluated for the ability to eliminate or minimize the waste streams exiting the process. Therefore, the PWA provides the basic tool for the creation of a comprehensive process baseline and identification of opportunities to eliminate/minimize the release of hazardous and non-hazardous wastes. This presentation will describe the status and activities of the program conceived to initiate PWAs at the Kansas City Division (KCD) of Allied-Signal Inc.. This program is organized through business units Which consist of manufacturing, quality, and engineering personnel from a specific product line. The departments that these business units represent are the generators of the major process waste at the KCD. Included in the update will be a brief overview of the lessons learned from the methodology development and

Integrated refinery waste management

Energy Technology Data Exchange (ETDEWEB)

Shieh, Y -S [ETG Environmental, Inc., Blue Bell, PA (US); Sheehan, W J [Separation and Recovery Systems, Inc., Irvine, CA (US)

1992-01-01

In response to the RCRA land ban regulations and TC rule promulgated by the U.S. Federal Environmental Protection Agency (EPA) in 1988-1990, an Integrated Refinery Waste Management (IRWM) program has been developed to provide cost-effective solutions to petroleum industry customers. The goal of IRWM is to provide technology based remediation treatment services to manage sludges and wastewaters generated from the oil refining processes, soils contaminated with petroleum distillates and groundwater contaminated with fuels. Resource recovery, volume reduction and waste minimization are the primary choices to mitigate environmental problems. Oil recovery has been performed through phase separation (such as centrifugation and filtration) and heating of heavy oils. Volume reduction is achieved by dewatering systems such as centrifuges and filter presses, and low temperature thermal treatment. Waste minimization can be accomplished by bioremediation and resource recovery through a cement kiln. (Author).

Waste. The political significance of the city’s suppressed other

Directory of Open Access Journals (Sweden)

Chrysanthe Constantinou

2015-03-01

Full Text Available MBeneath the city’s achievement as a grand machine of accumulation of matter, in invisibility lies the vast and vague sphere of waste accumulation. In invisibility, a huge network of waste flows is possibly rewriting economies as we know them, reproducing life conditions driven by the politics of wealth. In this parallel territory, recycling is a big business for the few.

Plans for Managing Hanford Remote Handled Transuranic (TRU) Waste

International Nuclear Information System (INIS)

MCKENNEY, D.E.

2001-01-01

The current Hanford Site baseline and life-cycle waste forecast predicts that approximately 1,000 cubic meters of remote-handled transuranic (RH-TRU) waste will be generated by waste management and environmental restoration activities at Hanford. These 1,000 cubic meters, comprised of both transuranic and mixed transuranic (TRUM) waste, represent a significant portion of the total estimated inventory of RH-TRU to be disposed of at the Waste Isolation Pilot Plant (WIPP). A systems engineering approach is being followed to develop a disposition plan for each RH-TRU/TRUM waste stream at Hanford. A number of significant decision-making efforts are underway to develop and finalize these disposition plans, including: development and approval of a RH-TRU/TRUM Waste Project Management Plan, revision of the Hanford Waste Management Strategic Plan, the Hanford Site Options Study (''Vision 2012''), the Canyon Disposal Initiative Record-of-Decision, and the Hanford Site Solid (Radioactive and Hazardous) Waste Program Environmental Impact Statement (SW-EIS). Disposition plans may include variations of several options, including (1) sending most RH-TRU/TRUM wastes to WIPP, (2) deferrals of waste disposal decisions in the interest of both efficiency and integration with other planned decision dates and (3) disposition of some materials in place consistent with Department of Energy Orders and the regulations in the interest of safety, risk minimization, and cost. Although finalization of disposition paths must await completion of the aforementioned decision documents, significant activities in support of RH-TRU/TRUM waste disposition are proceeding, including Hanford participation in development of the RH TRU WIPP waste acceptance criteria, preparation of T Plant for interim storage of spent nuclear fuel sludge, sharing of technology information and development activities in cooperation with the Mixed Waste Focus Area, RH-TRU technology demonstrations and deployments, and

Conceptual designs of automated systems for underground emplacement and retrieval of nuclear waste

International Nuclear Information System (INIS)

Slocum, A.H.; Hou, W.M.; Park, K.; Hochmuth, C.; Thurston, D.C.

1987-01-01

Current designs of underground nuclear waste repositories have not adequately addressed the possibility of automated, unmanned emplacement and retrieval. This report will present design methodologies for development of an automated system for underground emplacement of nuclear waste. By scaling generic issues to different repositories, it is shown that a two vehicle automated waste emplacement/retrieval system can be designed to operate in a fail-safe mode. Evaluation of cost at this time is not possible. Significant gains in worker safety, however, can be realized by minimizing the possibility of human exposure

Environmental assessment, finding of no significant impact, and response to comments. Radioactive waste storage

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-04-01

The Department of Energy`s (DOE) Rocky Flats Environmental Technology Site (the Site), formerly known as the Rocky Flats Plant, has generated radioactive, hazardous, and mixed waste (waste with both radioactive and hazardous constituents) since it began operations in 1952. Such wastes were the byproducts of the Site`s original mission to produce nuclear weapons components. Since 1989, when weapons component production ceased, waste has been generated as a result of the Site`s new mission of environmental restoration and deactivation, decontamination and decommissioning (D&D) of buildings. It is anticipated that the existing onsite waste storage capacity, which meets the criteria for low-level waste (LL), low-level mixed waste (LLM), transuranic (TRU) waste, and TRU mixed waste (TRUM) would be completely filled in early 1997. At that time, either waste generating activities must cease, waste must be shipped offsite, or new waste storage capacity must be developed.

Environmental assessment, finding of no significant impact, and response to comments. Radioactive waste storage

International Nuclear Information System (INIS)

1996-04-01

The Department of Energy's (DOE) Rocky Flats Environmental Technology Site (the Site), formerly known as the Rocky Flats Plant, has generated radioactive, hazardous, and mixed waste (waste with both radioactive and hazardous constituents) since it began operations in 1952. Such wastes were the byproducts of the Site's original mission to produce nuclear weapons components. Since 1989, when weapons component production ceased, waste has been generated as a result of the Site's new mission of environmental restoration and deactivation, decontamination and decommissioning (D ampersand D) of buildings. It is anticipated that the existing onsite waste storage capacity, which meets the criteria for low-level waste (LL), low-level mixed waste (LLM), transuranic (TRU) waste, and TRU mixed waste (TRUM) would be completely filled in early 1997. At that time, either waste generating activities must cease, waste must be shipped offsite, or new waste storage capacity must be developed

Waste minimization methods for treating analytical instrumentation effluents at the source

International Nuclear Information System (INIS)

Ritter, J.A.; Barnhart, C.

1995-01-01

The primary goal of this project was to reduce the amount of hazardous waste being generated by the Savannah River Siste Defense Waste Processing Technology-analytical Laboratory (DWPT-AL). A detailed characterization study was performed on 12 of the liquid effluent streams generated within the DWPT-AL. Two of the streams were not hazardous, and are now being collected separately from the 10 hazardous streams. A secondary goal of the project was to develop in-line methods using primarily adsorption/ion exchange columns to treat liquid effluent as it emerges from the analytical instrument as a slow, dripping flow. Samples from the 10 hazardous streams were treated by adsorption in an experimental apparatus that resembled an in-line or at source column apparatus. The layered adsorbent bed contained activated carbon and ion exchange resin. The column technique did not work on the first three samples of the spectroscopy waste stream, but worked well on the next three samples which were treated in a different column. It was determined that an unusual form of mercury was present in the first three samples. Similarly, two samples of a combined waste stream were rendered nonhazardous, but the last two samples contained acetylnitrile that prevented analysis. The characteristics of these streams changed from the initial characterization study; therefore, continual, in-deptch stream characterization is the key to making this project successful

Optimization of municipal solid waste collection and transportation routes.

Science.gov (United States)

Das, Swapan; Bhattacharyya, Bidyut Kr

2015-09-01

Optimization of municipal solid waste (MSW) collection and transportation through source separation becomes one of the major concerns in the MSW management system design, due to the fact that the existing MSW management systems suffer by the high collection and transportation cost. Generally, in a city different waste sources scatter throughout the city in heterogeneous way that increase waste collection and transportation cost in the waste management system. Therefore, a shortest waste collection and transportation strategy can effectively reduce waste collection and transportation cost. In this paper, we propose an optimal MSW collection and transportation scheme that focus on the problem of minimizing the length of each waste collection and transportation route. We first formulize the MSW collection and transportation problem into a mixed integer program. Moreover, we propose a heuristic solution for the waste collection and transportation problem that can provide an optimal way for waste collection and transportation. Extensive simulations and real testbed results show that the proposed solution can significantly improve the MSW performance. Results show that the proposed scheme is able to reduce more than 30% of the total waste collection path length. Copyright © 2015 Elsevier Ltd. All rights reserved.

Laboratory waste minimization during the operation startup phase

International Nuclear Information System (INIS)

Morrison, J.A.

1995-05-01

The Waste Sampling and Characterization Facility (WSCF) Laboratory was opened for occupancy in October, 1994. It is the first of its kind on the Hanford Site, a low level lab located in an area of high level radiological material. The mission of the facility is to analyze process samples from two on-line effluent treatment plants. One of these plants is operating and the other is due to begin operations by the end of 1995. The VSCF also performs air sampling analysis for routine radiological surveillance filter papers drawn from around the Hanford Site. Because this type of laboratory had not been in operation before, there was only speculation about the types and amounts of waste that would be generated. The laboratory personnel assigned to WSCF were assembled from existing labs on the Hanford Site and from outside the Hanford Site community. For some, it was a first time experience working on a site where a twenty mile drive is sometimes required to visit another building. For others, it was a change in the way business is conducted using state-of-the-art equipment, a new building, and a chance to approach issues as a team from the beginning. It is how this team came together and the issues that were discussed, sometimes uncomfortably, that lead to the current success. The outcome of this process is discussed in this paper

Waste paper recycling opportunities for government action. Vol. 4, corrugated waste. Final report

Energy Technology Data Exchange (ETDEWEB)

Bailey, J.; Love, P.

1978-01-01

This study analyzes current and expected corrugated waste market conditions in Canada, with the objective of identifying government initiatives which could permanently increase recovery levels. Short-term, practical measures are featured. National and regional demand, generation and recovery levels are examined, along with imports and exports to the USA. Over 70% of corrugated waste is consumed in Ontario and Quebec, and most of this waste is generated in those two provinces. Average recovery rates in most major urban areas are estimated at 30-40%. Future demand, generation, and recovery are estimated, and it is suggested that there will be enough domestic demand to permit reclamation of nearly 35% of Canada's total corrugated wastes. This potential level is not expected to change significantly, and new demand opportunities appear minimal. Examination of the potential for future imports from the USA indicates that availability will tighten over the medium term, necessitating a search for new corrugated waste supply sources. Possible sources include supermakets, retail chains and large assembly manufacturing establishments; one of the most promising of these sources is shopping malls, and a study is appended which examines the feasibility of a corrugated waste source separation program within a hypothetical mall. Possible government actions are outlined to improve reclamation and recycling of corrugated waste in Canada, including the improvement of local recovery capabilities in British Columbia, Ontario and Quebec, and the reduction of freight costs for moving corrugated waste from low-recovery areas to high-demand areas. 26 refs., 9 figs., 31 tabs.

Improvements of radioactive waste management at WWER nuclear power plants

International Nuclear Information System (INIS)

2006-04-01

This report is part of a systematic IAEA effort to improve waste management practices at WWER plants and to make them consistent with the current requirements and standards for safe and reliable operation of nuclear power plants. The report reviews the wet and dry solid waste management practices at the various types of WWER nuclear power plants (NPP) and describes approaches and recent achievements in waste minimization. Waste minimization practices in use at western PWRs are reviewed and compared, and their applicability at WWER plants is evaluated. Radioactive waste volume reduction issues and waste management practices are reflected in many IAEA publications. However, aspects of waste minimization specific to individual WWER nuclear power plant designs and WWER waste management policies are not addressed extensively in those publications. This report covers the important aspects applicable to the improvement of waste management at WWER NPP, including both plant-level and country-level considerations. It is recognized that most WWER plants are already implementing many of these concepts and recommendations with varying degrees of success; others will benefit from the included considerations. The major issues addressed are: - Review of current waste management policies and practices related to WWERs and western PWRs, including the influence of the original design concepts and significant modifications, liquid waste discharge limits and dry solid waste clearance levels applied in individual countries, national policies and laws, and other relevant aspects affecting the nature and quantities of waste arisings; - Identification of strategies and methods for improving the radioactive waste management generated in normal operation and maintenance at WWERs. This report is a composite (combination) of the two separate initiatives mentioned above. The first draft report was prepared at the meeting 26-30 May 1997 by five consultants. The draft was improved during an

Significant volume reduction of tank waste by selective crystallization: 1994 Annual report

International Nuclear Information System (INIS)

Herting, D.L.; Lunsford, T.R.

1994-01-01

The objective of this technology task plan is to develop and demonstrate a scaleable process of reclaim sodium nitrate (NaNO 3 ) from Hanford waste tanks as a clean nonradioactive salt. The purpose of the so-called Clean Salt Process is to reduce the volume of low level waste glass by as much as 70%. During the reporting period of October 1, 1993, through May 31, 1994, progress was made on four fronts -- laboratory studies, surrogate waste compositions, contracting for university research, and flowsheet development and modeling. In the laboratory, experiments with simulated waste were done to explore the effects of crystallization parameters on the size and crystal habit of product NaNO 3 crystals. Data were obtained to allows prediction of decontamination factor as a function of solid/liquid separation parameters. Experiments with actual waste from tank 101-SY were done to determine the extent of contaminant occlusions in NaNO 3 crystals. In preparation for defining surrogate waste compositions, single shell tanks were categorized according to the weight percent NaNO 3 in each tank. A detailed process flowsheet and computer model were created using the ASPENPlus steady state process simulator. This is the same program being used by the Tank Waste Remediation System (TWRS) program for their waste pretreatment and disposal projections. Therefore, evaluations can be made of the effect of the Clean Salt Process on the low level waste volume and composition resulting from the TWRS baseline flowsheet. Calculations, using the same assumptions as used for the TWRS baseline where applicable indicate that the number of low level glass vaults would be reduced from 44 to 16 if the Clean Salt Process were incorporated into the baseline flowsheet

The significance of avoiding household food waste - A means-end-chain approach.

Science.gov (United States)

Richter, Beate; Bokelmann, Wolfgang

2018-04-01

Many humans suffer from hunger, while edible food is discarded. This study aims at showing the importance of avoiding food waste in households and its causes by applying the means-end-chain analysis. Additional the means-end-chain approach should be examined in how far the method is suitable to get insights towards this topic. Consumer backgrounds in terms of feelings and attitudes regarding food waste should be shown, with the particular question why food waste personally is important. The data collection occurred utilizing the hard laddering method within a quantitative online survey. The results indicate that avoiding food waste is important for the greater part of consumers, as many claim to have a bad conscience, seeing it as morally wrong and reprehensible to waste food. A sample breakdown of gender, age and income points differences among these groups in regards to psychological consequences and value systems. Financial and environmental aspects have a lesser impact on attitudes and feelings regarding food waste in households. Copyright © 2018 Elsevier Ltd. All rights reserved.

Methodology of economic efficiency assessment and its application to radioactive waste management

International Nuclear Information System (INIS)

Petr, J.

1988-01-01

The share of the radioactive waste treatment process in the total economic balance of nuclear power plants is assessed. Only liquid wastes are considered for simplification. The amount, specific activity and concentration are the basic parameters significant from the economic point of view. The solution of problems associated with the radioactive waste formation (its minimization, e.g., by improving leakproofness, limiting the number of rinsings, optimization of chemical operation regimens) and sorting exhibits an economic effect several times higher (as much as an order of magnitude) than it is theoretically attainable by improving the disposal process. (M.D.). 2 figs

Assessment of Malaysia Institutional radioactive waste management

International Nuclear Information System (INIS)

Syed Hakimi Sakuma; Nik Marzukee; Ibrahim Martibi

1996-01-01

A complete inventory of radioactive wastes from different source bas been set up in Malaysia. Wastes from external agencies were sent to the National Radioactive Waste Management Center at MINT for final disposal. MINT has been collecting information on the accumulated wastes received since 1982. Assessment of radioactive waste management in Malaysia has been conducted based on the inventory record. The information in the inventory include description of users, type volume, characteristics of the wastes; and the current and accumulated activities of the radioisotopes in the wastes forms while storing. The records indicate that there is a significant increase in the volume of wastes from medical and industrial applications. The category of users varies; there are about 270 industrial users, about 60 in medical fields and 13 in research institutes and universities. Major users generating sealed source wastes for the industrial sector are services, manufacturing and consumer companies; including government department and universities. It is estimated that by the year 2005, approximately a total accumulated processed waste package volume for disposal will be between 210-215 m sup 3. This estimate includes low level and intermediate level wastes. From this study, future waste management activities in Malaysia can be planned with proper policy decision, treatment conditioning, storage and disposal facilities. This will enable radioactive wastes to be kept under control and their potential impact on man and the environment to be minimal

Plasma separation process: Disposal of PSP radioactive wastes

International Nuclear Information System (INIS)

1989-07-01

Radioactive wastes, in the form of natural uranium contaminated scrap hardware and residual materials from decontamination operations, were generated in the PSP facilities in buildings R1 and 106. Based on evaluation of the characteristics of these wastes and the applicable regulations, the various options for the processing and disposal of PSP radioactive wastes were investigated and recommended procedures were developed. The essential features of waste processing included: (1) the solidification of all liquid wastes prior to shipment; (2) cutting of scrap hardware to fit 55-gallon drums and use of inerting agents (diatomaceous earth) to eliminate pyrophoric hazards; and (3) compaction of soft wastes. All PSP radioactive wastes were shipped to the Hanford Site for disposal. As part of the waste disposal process, a detailed plan was formulated for handling and tracking of PSP radioactive wastes, from the point of generation through shipping. In addition, a waste minimization program was implemented to reduce the waste volume or quantity. Included in this document are discussions of the applicable regulations, the types of PSP wastes, the selection of the preferred waste disposal approach and disposal site, the analysis and classification of PSP wastes, the processing and ultimate disposition of PSP wastes, the handling and tracking of PSP wastes, and the implementation of the PSP waste minimization program. 9 refs., 1 fig., 8 tabs

Pollution prevention opportunity assessment: Foundation of pollution prevention for waste management

International Nuclear Information System (INIS)

Damewood, R.W.

1994-01-01

The objective of this paper is to promote the Pollution Prevention Opportunity Assessment (PPOA) technique as a fundamental of pollution prevention for waste management. All key elements of an effective PPOA program are presented. These key elements include impacts of environmental laws on pollution prevention, PPOA concepts and overview, waste minimization opportunities assessment, reporting and monitoring waste minimization progress, and PPOA program implementation. As environmental laws evolve the focus is shifting from end-of-pipe pollution control to front-end source reduction. Waste minimization was mistakenly interpreted to mean the reduction of hazardous waste after generation in the past. The Pollution Prevention Act of 1990 has clearly defined its requirement on resource reduction. Waste reduction can be viewed as a criterion to assess all industrial processes and operations. The fundamental approach of PPOA focuses on a mass balance concept. This concept deals with tracking of chemicals from the point of purchase, through storage, utilization in the process, and waste generation at the end of process. In other words, PPOA is a technique to analyze this input/output process. By applying PPOA techniques, the framework of applicable compliance requirements to the current operation process is established. Furthermore, documentation of PPOA itself can meet as documentation requirements for environmental compliance. In general, the PPOA process consists of two phases. The first phase involves input and output process description and waste characterization. The second phase is an opportunities assessment for waste minimization from input/output waste characterization. These two phases are explained in detail in the paper

Hazardous Waste Cerification Plan: Hazardous Waste Handling Facility, Lawrence Berkeley Laboratory

International Nuclear Information System (INIS)

1992-02-01

The purpose of this plan is to describe the organization and methodology for the certification of hazardous waste (HW) handled in the Lawrence Berkeley Laboratory (LBL) Hazardous Waste Handling Facility (HWHF). The plan also incorporates the applicable elements of waste reduction, which include both up-front minimization and end- product treatment to reduce the volume and toxicity of the waste; segregation of the waste as it applies to certification; and executive summary of the Quality Assurance Program Plan (QAPP) for the HWHF and a list of the current and planned implementing procedures used in waste certification. The plan provides guidance from the HWHF to waste generators, waste handlers, and the Systems Group Manager to enable them to conduct their activities and carry out their responsibilities in a manner that complies with several requirements of the Federal Resource Conservation and Resource Recovery Act (RCRA), the Federal Department of Transportation (DOT), and the State of California, Code of Regulations (CCR), Title 22

Combined Waste Form Cost Trade Study

International Nuclear Information System (INIS)

Gombert, Dirk; Piet, Steve; Trickel, Timothy; Carter, Joe; Vienna, John; Ebert, Bill; Matthern, Gretchen

2008-01-01

A new generation of aqueous nuclear fuel reprocessing, now in development under the auspices of the DOE Office of Nuclear Energy (NE), separates fuel into several fractions, thereby partitioning the wastes into groups of common chemistry. This technology advance enables development of waste management strategies that were not conceivable with simple PUREX reprocessing. Conventional wisdom suggests minimizing high level waste (HLW) volume is desirable, but logical extrapolation of this concept suggests that at some point the cost of reducing volume further will reach a point of diminishing return and may cease to be cost-effective. This report summarizes an evaluation considering three groupings of wastes in terms of cost-benefit for the reprocessing system. Internationally, the typical waste form for HLW from the PUREX process is borosilicate glass containing waste elements as oxides. Unfortunately several fission products (primarily Mo and the noble metals Ru, Rh, Pd) have limited solubility in glass, yielding relatively low waste loading, producing more glass, and greater disposal costs. Advanced separations allow matching the waste form to waste stream chemistry, allowing the disposal system to achieve more optimum waste loading with improved performance. Metals can be segregated from oxides and each can be stabilized in forms to minimize the HLW volume for repository disposal. Thus, a more efficient waste management system making the most effective use of advanced waste forms and disposal design for each waste is enabled by advanced separations and how the waste streams are combined. This trade-study was designed to juxtapose a combined waste form baseline waste treatment scheme with two options and to evaluate the cost-benefit using available data from the conceptual design studies supported by DOE-NE

Addressing mixed waste in plutonium processing

International Nuclear Information System (INIS)

Christensen, D.C.; Sohn, C.L.; Reid, R.A.

1991-01-01

The overall goal is the minimization of all waste generated in actinide processing facilities. Current emphasis is directed toward reducing and managing mixed waste in plutonium processing facilities. More specifically, the focus is on prioritizing plutonium processing technologies for development that will address major problems in mixed waste management. A five step methodological approach to identify, analyze, solve, and initiate corrective action for mixed waste problems in plutonium processing facilities has been developed

SIGNIFICANT PROGRESS IN THE DEPLOYMENT OF NEW TECHNOLOGIES FOR THE RETRIEVAL OF HANFORD RADIOACTIVE WASTE STORAGE TANKS

International Nuclear Information System (INIS)

RAYMOND RE; DODD RA; CARPENTER KE; STURGES MH

2008-01-01

Significant enhancements in the development and deployment of new technologies for removing waste from storage tanks at the Hanford Site have resulted in accelerated progress and reduced costs for tank cleanup. CH2M HILL Hanford Group, Inc. is the U.S. Department of Energy, Office of River Protection's prime contractor responsible for safely storing and retrieving approximately 53 million gallons of highly-radioactive and hazardous waste stored in 177 underground tanks. The waste is stored in 149 older single-shell tanks (SST) and 28 newer double-shell tanks (DST) that are grouped in 18 so-called farms near the center of the Hanford Site, located in southeastern Washington State. Tank contents include materials from years of World-War II and post-war weapons production, which account for 60 percent by volume of the nation's high-level radioactive waste. A key strategy for improved cleanup is the development and deployment of innovative technologies, which enhance worker safety, resolve technical challenges, streamline retrieval processes, and cut project costs and durations. During the past seven years of tank cleanout projects we have encountered conditions and waste chemistry that defy conventional approaches, requiring a variety of new tools and techniques. Through the deployment of advanced technology and the creative application of resources, we are finding ways to accomplish the retrieval process safely, swiftly, and economically. To date, retrieval operations have been completed in seven tanks, including a record six tanks in a two-year period. Retrieval operations are in progress for another three tanks. This paper describes the following tank cleanup technologies deployed at Hanford in the past few years: Modified waste sluicing, High pressure water lance, Mobile retrieval tools, Saltcake dissolution, Vacuum retrieval, Sparging of wastes, Selective dissolution for waste treatment, Oxalic acid dissolution, High-pressure water mixers, Variable height pumps

Storage of radioactive wastes

International Nuclear Information System (INIS)

1992-07-01

Even if the best waste minimization measures are undertaken throughout radioisotope production or usage, significant radioactive wastes arise to make management measures essential. For developing countries with low isotope usage and little or no generation of nuclear materials, it may be possible to handle the generated waste by simply practicing decay storage for several half-lives of the radionuclides involved, followed by discharge or disposal without further processing. For those countries with much larger facilities, longer lived isotopes are produced and used. In this situation, storage is used not only for decay storage but also for in-process retention steps and for the key stage of interim storage of conditioned wastes pending final disposal. The report will serve as a technical manual providing reference material and direct step-by-step know-how to staff in radioisotope user establishments and research centres in the developing Member States without nuclear power generation. Considerations are limited to the simpler storage facilities. The restricted quantities and low activity associated with the relevant wastes will generally permit contact-handling and avoid the need for shielding requirements in the storage facilities or equipment used for handling. A small quantity of wastes from some radioisotope production cells and from reactor cooling water treatment may contain sufficient short lived activity from activated corrosion products to require some separate decay storage before contact-handling is suitable. 16 refs, 12 figs, 8 tabs

Waste treatment activities incineration

International Nuclear Information System (INIS)

Weber, D.A.

1985-01-01

The waste management policy at SRP is to minimize waste generation as much as possible and detoxify and/or volume reduce waste materials prior to disposal. Incineration is a process being proposed for detoxification and volume reduction of combustion nonradioactive hazardous, low-level mixed and low-level beta-gamma waste. Present operation of the Solvent Burner Demonstration reduces the amount of solid combustible low-level beta-gamma boxed waste disposed of by shallow land burial by approximately 99,000 ft 3 per year producing 1000 ft 3 per year of ash and, by 1988, will detoxify and volume reduce 150,000 gallons or organic Purex solvent producing approximately 250 ft 3 of ash per year

Nuclear Solid Waste Processing Design at the Idaho Spent Fuels Facility

International Nuclear Information System (INIS)

Dippre, M. A.

2003-01-01

A spent nuclear fuels (SNF) repackaging and storage facility was designed for the Idaho National Engineering and Environmental Laboratory (INEEL), with nuclear solid waste processing capability. Nuclear solid waste included contaminated or potentially contaminated spent fuel containers, associated hardware, machinery parts, light bulbs, tools, PPE, rags, swabs, tarps, weld rod, and HEPA filters. Design of the nuclear solid waste processing facilities included consideration of contractual, regulatory, ALARA (as low as reasonably achievable) exposure, economic, logistical, and space availability requirements. The design also included non-attended transfer methods between the fuel packaging area (FPA) (hot cell) and the waste processing area. A monitoring system was designed for use within the FPA of the facility, to pre-screen the most potentially contaminated fuel canister waste materials, according to contact- or non-contact-handled capability. Fuel canister waste materials which are not able to be contact-handled after attempted decontamination will be processed remotely and packaged within the FPA. Noncontact- handled materials processing includes size-reduction, as required to fit into INEEL permitted containers which will provide sufficient additional shielding to allow contact handling within the waste areas of the facility. The current design, which satisfied all of the requirements, employs mostly simple equipment and requires minimal use of customized components. The waste processing operation also minimizes operator exposure and operator attendance for equipment maintenance. Recently, discussions with the INEEL indicate that large canister waste materials can possibly be shipped to the burial facility without size-reduction. New waste containers would have to be designed to meet the drop tests required for transportation packages. The SNF waste processing facilities could then be highly simplified, resulting in capital equipment cost savings, operational

Getting a taste for food waste: a mixed methods ethnographic study into hospital food waste before patient consumption conducted at three New Zealand foodservice facilities.

Science.gov (United States)

Goonan, Sarah; Mirosa, Miranda; Spence, Heather

2014-01-01

Foodservice organizations, particularly those in hospitals, are large producers of food waste. To date, research on waste in hospitals has focused primarily on plate waste and the affect of food waste on patient nutrition outcomes. Less focus has been placed on waste generation at the kitchen end of the hospital food system. We used a novel approach to understand reasons for hospital food waste before consumption and offer recommendations on waste minimization within foodservices. A mixed methods ethnographic research approach was adopted. Three New Zealand hospital foodservices were selected as research sites, all of which were contracted to an external foodservice provider. Data collection techniques included document analyses, observations, focus groups with kitchen staff, and one-on-one interviews with managers. Thematic analysis was conducted to generate common themes. Most food waste occurred during service and as a result of overproduction. Attitudes and habits of foodservice personnel were considered influential factors of waste generation. Implications of food waste were perceived differently by different levels of staff. Whereas managers raised discussion from a financial perspective, kitchen staff drew upon social implications. Organizational plans, controls, and use of pre-prepared ingredients assisted in waste minimization. An array of factors influenced waste generation in hospital foodservices. Exploring attitudes and practices of foodservice personnel allowed an understanding of reasons behind hospital food waste and ways in which it could be minimized. This study provides a foundation for further research on sustainable behavior within the wider foodservice sector and dietetics practice. Copyright © 2014 Academy of Nutrition and Dietetics. Published by Elsevier Inc. All rights reserved.

Final waste management programmatic environmental impact statement for managing treatment, storage, and disposal of radioactive and hazardous waste. Volume IV of V