Systematics of criticality properties of actinide nuclides and its bearing on the long lived fission waste problem

International Nuclear Information System (INIS)

Srinivasan, M.; Rao, K.S.; Garg, S.B.; Iyengar, P.K.

1989-01-01

This paper reports on a systematic analysis of the criticality parameters of over twenty fissile and fertile isotopes of eight transthorium actinide elements that has been carried out by us. It is observed that K ∞ increases and critical mass decreases monotonically with the fissility parameter (Z 2 /A) of the nuclides. This implies that each and every isotope of transuranic elements such as Np, Am, Cm etc. which are produced as by-products during reactor operation is a more valuable nuclear fuel than the corresponding fissile/fissible isotopes of plutonium. This finding has a profound bearing on the long lived fission waste problem and supports the view that the byproduct actinide elements should be separated from the high level waste stream and recycled back into fission reactors, thereby eliminating one of the commonly voiced concerns regarding the acceptability of nuclear fission power

Microcalorimeter Q-spectroscopy for rapid isotopic analysis of trace actinide samples

Energy Technology Data Exchange (ETDEWEB)

Croce, M.P., E-mail: mpcroce@lanl.gov [Los Alamos National Laboratory, Los Alamos, NM (United States); Bond, E.M.; Hoover, A.S.; Kunde, G.J.; Mocko, V.; Rabin, M.W.; Weisse-Bernstein, N.R.; Wolfsberg, L.E. [Los Alamos National Laboratory, Los Alamos, NM (United States); Bennett, D.A.; Hays-Wehle, J.; Schmidt, D.R.; Ullom, J.N. [National Institute of Standards and Technology, Boulder, CO (United States)

2015-06-01

We are developing superconducting transition-edge sensor (TES) microcalorimeters that are optimized for rapid isotopic analysis of trace actinide samples by Q-spectroscopy. By designing mechanically robust TESs and simplified detector assembly methods, we have developed a detector for Q-spectroscopy of actinides that can be assembled in minutes. We have characterized the effects of each simplification and present the results. Finally, we show results of isotopic analysis of plutonium samples with Q-spectroscopy detectors and compare the results to mass spectrometry.

Microcalorimeter Q-spectroscopy for rapid isotopic analysis of trace actinide samples

International Nuclear Information System (INIS)

Croce, M.P.; Bond, E.M.; Hoover, A.S.; Kunde, G.J.; Mocko, V.; Rabin, M.W.; Weisse-Bernstein, N.R.; Wolfsberg, L.E.; Bennett, D.A.; Hays-Wehle, J.; Schmidt, D.R.; Ullom, J.N.

2015-01-01

We are developing superconducting transition-edge sensor (TES) microcalorimeters that are optimized for rapid isotopic analysis of trace actinide samples by Q-spectroscopy. By designing mechanically robust TESs and simplified detector assembly methods, we have developed a detector for Q-spectroscopy of actinides that can be assembled in minutes. We have characterized the effects of each simplification and present the results. Finally, we show results of isotopic analysis of plutonium samples with Q-spectroscopy detectors and compare the results to mass spectrometry

Determination of long-lived actinides in soil leachates by inductively coupled plasma: Mass spectrometry

International Nuclear Information System (INIS)

Crain, J.S.; Smith, L.L.; Yaeger, J.S.; Alvarado, J.A.

1994-01-01

Inductively coupled plasma -- mass spectrometry (ICP-MS) was used to concurrently determine multiple long-lived (t 1/2 > 10 4 y) actinide isotopes in soil samples. Ultrasonic nebulization was found to maximize instrument sensitivity. Instrument detection limits for actinides in solution ranged from 50 mBq L -1 ( 239 Pu) to 2 μBq L -1 ( 235 U) Hydride adducts of 232 Th and 238 U interfered with the determinations of 233 U and 239 Pu; thus, extraction chromatography was, used to eliminate the sample matrix, concentrate the analytes, and separate uranium from the other actinides. Alpha spectrometric determinations of 230 Th, 239 Pu, and the 234 U/ 238 U activity ratio in soil leachates compared well with ICP-MS determinations; however, there were some small systematic differences (ca. 10%) between ICP-MS and a-spectrometric determinations of 234 U and 238 U activities

Calculated investigation of actinide transmutation in the BOR-60 reactor

International Nuclear Information System (INIS)

Zhemkov, I.Yu.; Ishunina, O.V.; Yakovleva, I.V.

2001-01-01

In the course of reactor operation the formation of fission products and accumulation of minor-actinides and plutonium take place in the nuclear fuel. These materials define the radiation hazard to a great extent. Of one possible ways lowering the activity of irradiated nuclear fuel is transmutation of long-lived radioactive isotopes in the stable or short-lived ones, that allows to facilitate the problem of the high-level waste and to improve the efficiency of nuclear fuel use at the expense of its recycling and burnup increasing. (authors)

[Hyperfine structure and isotope shift measurements of short lived elements by laser spectroscopy

International Nuclear Information System (INIS)

Schuessler, H.A.

1986-01-01

The aim of this research is to determine nuclear moments and charge distributions of short-lived isotopes produced both on-line and off-line to a nuclear facility. These measurements give detailed information on the nuclear force and are used to test current nuclear models. The small amounts of nuclei which can be produced off stability constitute the challenge in these experiments. Presently mainly neutron-rich isotopes are being studied by three ultrasensitive high-resolution laser techniques. These are collinear fast ion-beam laser spectroscopy, stored-ion laser spectroscopy and fluorescence spectroscopy. 5 figs

Short-lived radionuclide production capability at the Brookhaven Linac Isotope Producer

International Nuclear Information System (INIS)

Mausner, L.F.; Richards, P.

1985-01-01

The Brookhaven National Linac Isotope Producer is the first facility to demonstrate the capability of a large linear accelerator for efficient and economical production of difficult-to-make, medically useful radionuclides. The linac provides a beam of 200-MeV protons at an integrated beam current of up to 60 μA. The 200-MeV proton energy is very suitable for isotope production because the spallation process can create radionuclides unavailable at lower energy accelerators or reactors. Several medically important short-lived radionuclides are presently being prepared for on-site and off-site collaborative research programs. These are iodine-123, iron-52, manganese-52m, ruthenium-97, and the rubidium-81-krypton-81m system. The production parameters for these are summarized

Burning minor actinides in a HTR energy spectrum

International Nuclear Information System (INIS)

Pohl, Christoph; Rütten, H. Jochem

2012-01-01

Highlights: ► Burn-up analysis for varying plutonium/minor actinide fuel compositions. ► The influence of varying heavy metal fuel element loads is investigated. ► Significant burn-up via radiative capture and subsequently fission is observed. ► Difference observed between fuel element burn-up and total actinide burning rate. - Abstract: The generation of nuclear energy by means of the existing nuclear reactor systems is based mainly on the fission of U-235. But this comes along with the capture of neutrons by the U-238 faction and results in a build-up of plutonium isotopes and minor actinides as neptunium, americium and curium. These actinides are dominant for the long time assessment of the radiological risk of a final disposal therefore a minimization of the long living isotopes is aspired. Burning the actinides in a high temperature helium cooled graphite moderated reactor (HTR) is one of these options. The use of plutonium isotopes to sustain the criticality of the system is intended to avoid on the one hand highly enriched uranium because of international regulations and on the other hand low enriched uranium because of the build up of new actinides from neutron capture in the U-238 fraction. Because initial minor actinide isotopes are typically not fissionable by thermal neutrons the idea is to fission instead the intermediate isotopes generated by the first neutron capture. This paper comprises calculations for plutonium/minor actinides/thorium fuel compositions and their correlated final burn-up for a generic pebble bed HTR based on the reference design of the 400 MW PBMR. In particular the cross sections and the neutron balance of the different minor actinide isotopes in the higher thermal energy spectrum of a HTR will be discussed. For a fuel mixture of plutonium and minor actinides a significant burn-up of these actinides up to 20% can be achieved but at the expense of a higher residual fraction of plutonium in the burned fuel. Combining

Determination of nuclear spins of short-lived isotopes by laser induced fluorescence

International Nuclear Information System (INIS)

Buchinger, F.; Dabkiewicz, P.; Kremmling, H.; Kuehl, T.; Mueller, A.C.; Schuessler, H.A.

1980-01-01

The spins of several nuclear ground and isomeric states have been measured for a number of mercury isotopes. The fluorescent light from the 6s6p 3 P 1 state is observed at 2537 Angstroem after excitation with the frequency doubled output of a pulsed dye laser. Four different laser induced fluorescence techniques were tested for their applicability: double resonance, Hanle effect, time delayed integral Hanle beats, and time resolved quantum beats. The sensitivity and selectivity of these models are compared with emphasis on the determination of spins of nuclei far from beta-stability, where short half lives and low production yields restrict the number of available atoms. The experiments were carried out on-line with the ISOLDE isotope separator at CERN at densities as low as 10 6 atoms/cm 3 . Results for the very neutron deficient high spin mercury isomers with half lives of several seconds, but also for the ground states of the abundant low spin stable mercury isotopes, are given as examples. The test measurements determined the nuclear spins of the odd sup(185m-191m)Hg isomers to be I = 13/2. (orig.)

Safe actinide disposition in molten salt reactors

International Nuclear Information System (INIS)

Gat, U.

1997-01-01

Safe molten salt reactors (MSR) can readily accommodate the burning of all fissile actinides. Only minor compromises associated with plutonium are required. The MSRs can dispose safely of actinides and long lived isotopes to result in safer and simpler waste. Disposing of actinides in MSRs does increase the source term of a safety optimized MSR. It is concluded that the burning and transmutation of actinides in MSRs can be done in a safe manner. Development is needed for the processing to handle and separate the actinides. Calculations are needed to establish the neutron economy and the fuel management. 9 refs

Separation of actinides and long-lived fission products from high-level radioactive wastes (a review)

International Nuclear Information System (INIS)

Kolarik, Z.

1991-11-01

The management of high-level radioactive wastes is facilitated, if long-lived and radiotoxic actinides and fission products are separated before the final disposal. Especially important is the separation of americium, curium, plutonium, neptunium, strontium, cesium and technetium. The separated nuclides can be deposited separately from the bulk of the high-level waste, but their transmutation to short-lived nuclides is a muchmore favourable option. This report reviews the chemistry of the separation of actinides and fission products from radioactive wastes. The composition, nature and conditioning of the wastes are described. The main attention is paid to the solvent extraction chemistry of the elements and to the application of solvent extraction in unit operations of potential partitioning processes. Also reviewed is the behaviour of the elements in the ion exchange chromatography, precipitation, electrolysis from aqueous solutions and melts, and the distribution between molten salts and metals. Flowsheets of selected partitioning processes are shown and general aspects of the waste partitioning are shortly discussed. (orig.) [de

Production of actinide isotopes in simulated PWR fuel and their influence on inherent neutron emission

International Nuclear Information System (INIS)

Bosler, G.E.; Phillips, J.R.; Wilson, W.B.; LaBauve, R.J.; England, T.R.

1982-07-01

This report describes calculations that examine the sensitivity of actinide isotopes to various reactor parameters. The impact of actinide isotope build-up, depletion, and decay on the neutron source rate in a spent-fuel assembly is determined, and correlations between neutron source rates and spent-fuel characteristics such as exposure, fissile content, and plutonium content are established. The application of calculations for evaluating experimental results is discussed

Biological pathways and chemical behavior of plutonium and other actinides in the environment

International Nuclear Information System (INIS)

Dahlman, R.C.; Bondietti, E.A.; Eyman, L.D.

1976-01-01

The principal long-lived actinide elements that may enter the environment from either U or Pu fuel cycles are Pu, Am, Cm, and Np. Approximately 25% of the alpha activity estimated to be released to the atmosphere from the LMFBR fuel cycle will be contributed by 241 Am, 242 Cm, and 244 Cm. The balance of the alpha activity will come from Pu isotopes. Activities of 242 Cm, 244 Cm, 241 Am, 243 Am, and 237 Np in waste may exceed concentrations of Pu isotopes in waste after various periods of decay. Thorium and uranium isotopes may also be released by operations of the thorium fuel cycle. Environmental actinides are discussed under the following headings: sources of man-made actinide elements; pathways of exposure; environmental chemistry of actinides; uptake of actinides by plants; distribution of actinides in components of White Oak Lake; entry of actinides into terrestrial food chains; relationship between chemical behavior and uptake of actinides by organisms; and behavior of Pu in freshwater and marine food chains

Minor actinide transmutation in accelerator driven systems

Energy Technology Data Exchange (ETDEWEB)

Friess, Friederike [IANUS, TU Darmstadt (Germany)

2015-07-01

Transmutation of radioactive waste, the legacy of nuclear energy use, gains rising interest. This includes the development of facilities able to transmute minor actinides (MA) into stable or short-lived isotopes before final disposal. The most common proposal is to use a double-strata approach with accelerator-driven-systems (ADS) for the efficient transmutation of MA and power reactors to dispose plutonium. An ADS consists of a sub-critical core that reaches criticality with neutrons supplied by a spallation target. An MCNP model of the ADS system Multi Purpose Research Reactor for Hightech Applications will be presented. Depletion calculations have been performed for both standard MOX fuel and transmutation fuel with an increased content of minor actinides. The resulting transmutation rates for MAs are compared to published values. Special attention is given to selected fission products such as Tc-99 and I-129, which impact the radiation from the spent fuel significantly.

Fission properties of very heavy actinides

International Nuclear Information System (INIS)

Hoffman, D.C.

1979-01-01

The existing data on neutron-emission, kinetic-energy and mass distributions, and half-lives for spontaneous fission of the heavy actinides are reviewed. A comparison of the data for the Fm isotopes with heavier and lighter nuclides suggests that the properties of the heavy Fm isotopes may be unique and can qualitatively be explained on the basis of fragment shell effects, i.e., symmetric fission results in two fragments with configurations close to the doubly magic 132 Sn nucleus. The effect of excitation energy and the use of systematics and theoretical predictions of fission properties and half-lives in the identification of new heavy element isotopes is discussed. 54 references

Simulation Studies of Diffusion-Release and Effusive-Flow of Short-Lived Radioactive Isotopes

CERN Document Server

Zhang, Yan; Kawai, Yoko

2005-01-01

Delay times associated with diffusion release from targets and effusive-flow transport of radioactive isotopes to ion sources are principal intensity limiters at ISOL-based radioactive ion beam facilities, and simulation studies with computer models are cost effective methods for designing targets and vapor transport systems with minimum delay times to avoid excessive decay losses of short lived ion species. A finite difference code, Diffuse II, was recently developed at the Oak Ridge National Laboratory to study diffusion-release of short-lived species from three principal target geometries. Simulation results are in close agreement with analytical solutions to Fick’s second equation. Complementary to the development of Diffuse II, the Monte-Carlo code, Effusion, was developed to address issues related to the design of fast vapor transport systems. Results, derived by using Effusion, are also found to closely agree with experimental measurements. In this presentation, the codes will be used in conc...

Biomolecular tracing using long-lived isotopes

International Nuclear Information System (INIS)

Vogel, J.S.; Turteltaub, K.W.; Frantz, C.E.; Keating, G.; Felton, J.S.; Southon, J.R.; Roberts, M.R.; Gledhill, B.L.

1992-01-01

Accelerator mass spectrometry (AMS) was developed over the past 15 years as an essential tool for detecting long-lived, cosmogenic radio-isotopes in the earth and space sciences. We apply this technology to the measurement of chemical kinetics, primarily in biomedical systems, which had heretofore employed short-lived isotopes and/or long counting times to quantify radio-isotopic labels. AMS provides detection efficiencies of ∼ 1%, 10 3 to 10 6 better than decay-counting. Long-lived isotopes are used and detected with AMS at concentrations which reduce sample size, chemical dose, radiation safety hazards and radiolysis. We measure 3 H, 7,1O Be, 14 C, 26 Al, 36 CI, 41 Ca and 129 I, but most of our current program uses 14 C. Initial experiments involved research on the genotoxicity of mutagens in cooked foods and reversible binding of compounds to antibodies. Through collaborations, we apply AMS detection to research in carcinogenesis, pharmacokinetics of toxins, elemental metabolism, distribution of topical medications and nutrition

Short-lived Isotopes from a Close-by AGB Star Triggering the Protosolar Nebula

Science.gov (United States)

Gallino, R.; Busso, M.; Wasserburg, G. J.; Straniero, O.

The presence of short-lived isotopes in the early solar system, in particular 26Al, 41Ca, 60Fe, and 107Pd, point to a close-by and fresh nucleosynthesis source, possibly triggering the collapse of the protosolar nebula. We present the results of nucleosynthesis calculations based on an AGB polluting hypothesis. A general concordance of the predicted yields of the above radioactivities relative to 26Al can be obtained in the case of an intermediate mass AGB star with hot bottom burning in the envelope (thus producing 26Al), and mixing through a series of third dredge-up episodes a fraction of the C-rich and s-processed material from the He intershell with the extended envelope. Polution of the protosolar nebula with freshly synthesized material may derive from the efficient winds of the AGB star. In AGB stars, the s-process nucleosynthesis occurs both during the maximum phase of every thermal runaway, driven by the partial activation of the 22Ne(alpha,n)25Mg reaction, and in the interpulse phase, where the 13C nuclei are fully consumed in radiative conditions by the activation of the 13C(alpha,n)16O reaction. We have used different prescriptions for the amount of the 13C nuclei present in the intershell. A minimum amount of 13C is naturally expected in the ashes of H-shell burning. Possible formation of an extra "13C-pocket" derives from the injection of a small amount of protons from the envelope into the 12C-rich intershell during any third dredge-up episode, when the H-shell is inactivated. Prediction for other short-lived, 36Cl, 135Cs, and 205Pb, are given. General consequences for the pollution of the protosolar nebula with newly synthesized stable isotopes from the AGB winds are outlined. The origin of other detected short-lived nuclei, in particular 53Mn, 129I, and 182Hf, which cannot come from an AGB source, is analysed. The alternative trigger hypothesis by a close-by Supernova is discussed.

Isotopic validation for PWR actinide-only burnup credit using Yankee Rowe data

International Nuclear Information System (INIS)

1997-11-01

Safety analyses of criticality control systems for transportation packages include an assumption that the spent nuclear fuel (SNF) loaded into the package is fresh or unirradiated. In other words, the spent fuel is assumed to have its original, as-manufactured U-235 isotopic content. The ''fresh fuel'' assumption is very conservative since the potential reactivity of the nuclear fuel is substantially reduced after being irradiated in the reactor core. The concept of taking credit for this reduction in nuclear fuel reactivity due to burnup of the fuel, instead of using the fresh fuel assumption in the criticality safety analysis, is referred to as ''Burnup Credit.'' Burnup credit uses the actual physical composition of the fuel and accounts for the net reduction of fissile material and the buildup of neutron absorbers in the fuel as it is irradiated. Neutron absorbers include actinides and other isotopes generated as a result of the fission process. Using only the change in actinide isotopes in the burnup credit criticality analysis is referred to as ''Actinide-Only Burnup Credit.'' The use of burnup credit in the design of criticality control systems enables more spent fuel to be placed in a package. Increased package capacity results in a reduced number of storage, shipping and disposal containers for a given number of SNF assemblies. Fewer shipments result in a lower risk of accidents associated with the handling and transportation of spent fuel, thus reducing both radiological and nonradiological risk to the public. This paper describes the modeling and the results of comparison between measured and calculated isotopic inventories for a selected number of samples taken from a Yankee Rowe spent fuel assembly

Helium and fission gas behaviour in magnesium aluminate spinel and zirconia for actinide transmutation

NARCIS (Netherlands)

Damen, P.M.G.

2003-01-01

In order to reduce the long-term radiotoxicity of spent nuclear fuel, many studies are performed on partitioning and transmutation of actinides. In such a scenario, the long-lived radio-isotopes (mostly actinides) are partitioned from the nuclear waste, and subsequently transmuted or fissioned in a

Casting of metallic fuel containing minor actinide additions

International Nuclear Information System (INIS)

Trybus, C.L.; Henslee, S.P.; Sanecki, J.E.

1992-01-01

A significant attribute of the Integral Fast Reactor (IFR) concept is the transmutation of long-lived minor actinide fission products. These isotopes require isolation for thousands of years, and if they could be removed from the waste, disposal problems would be reduced. The IFR utilizes pyroprocessing of metallic fuel to separate auranium, plutonium, and the minor actinides from nonfissionable constituents. These materials are reintroduced into the fuel and reirradiated. Spent IFR fuel is expected to contain low levels of americium, neptunium, and curium because the hard neutron spectrum should transmute these isotopes as they are produced. This opens the possibility of using an IFR to trnasmute minor actinide waste from conventional light water reactors (LWRs). A standard IFR fuel is based on the alloy U-20% Pu-10% Zr (in weight percent). A metallic fuel system eases the requirements for reprocessing methods and enables the minor actinide metals to be incorporated into the fuel with simple modifications to the basic fuel casting process. In this paper, the authors report the initial casting experience with minor actinide element addition to an IFR U-Pu-Zr metallic fuel

Practical applications of short-lived radioisotopes

Energy Technology Data Exchange (ETDEWEB)

NONE

1963-01-15

The advantages of the use of short-lived radioisotopes in agriculture, food industry and medicine as well as some industrial uses are discussed. Methods for isotope production in small research reactors and laboratories are presented

An easy method for the determination of Ra isotopes and actinide alpha emitters from the same water sample

International Nuclear Information System (INIS)

Moron, M.C.; Garcia-Tenorio, R.; Garcia-Montano, E.; Garcia-Leon, M.; Madurga, G.

1986-01-01

Radium isotopes and actinide α emitters are easily determined from the same water sample. The Ra fraction is obtained by coprecipitation with Ba, while a Fe coprecipitation is used for the actinides. Both fractions are measured with a gas-flow proportional counter. Additionally the isotopic Ra composition is obtained by measuring at two or three different times the α activity from the Ra-fraction. The method is applied to rain water and drinking water samples. (author)

Precision mass measurements of very short-lived, neutron-rich Na isotopes using a radiofrequency spectrometer

CERN Document Server

Lunney, M D; Doubre, H; Henry, S; Monsanglant, C; De Saint-Simon, M; Thibault, C; Toader, C F; Borcea, C; Bollen, G

2001-01-01

Mass measurements of high precision have been performed on sodium isotopes out to $^{30}$Na using a new technique of radiofrequency excitation of ion trajectories in a homogeneous magnetic field. This method, especially suited to very short-lived nuclides, has allowed us to significantly reduce the uncertainty in mass of the most exotic Na isotopes: a relative error of 5x10$^{-7}$ was achieved for $^{28}$Na having a half-life of only 30.5 ms and 9x10$^{-7}$ for the weakly produced $^{30}$Na. Verifying and minimizing binding energy uncertainties in this region of the nuclear chart is important for clarification of a long standing problem concerning the strength of the $N$=20 magic shell closure. These results are the fruit of the commissioning of the new experimental program Mistral.

Mass Measurement of Very Short Half-Lived Nuclei

CERN Document Server

Duma, M; Iacob, V E; Thibault, C

2002-01-01

The MISTRAL (Mass measurements at ISolde with a Transmission RAdiofrequency spectrometer on-Line) experiment exploits a rapid measurement technique to make accurate mass determinations of very short-lived nuclei. The physics goals are to elucidate new nuclear structure effects and constrain nuclear mass models in regions of interest to nuclear astrophysics.\\\\ \\\\The spectrometer, installed in May 97, performed as promised in the proposal with mass resolution exceeding 100,000. In its first experiment in July 1998, neutron-rich Na isotopes having half-lives as short as 31 ms were measured. A second experiment in November 1998 enabled us to improve the measurement precision of the isotopes $^{26-30}$Na to about 20 keV. The measurement program continues as experiment IS 373.

Utilization of fast reactor excess neutrons for burning minor actinides and long lived FPs

International Nuclear Information System (INIS)

Kawashima, K.; Kobayashi, K.; Kaneto, K.

1995-01-01

An evaluation is made on a large MOX fuel fast reactor's capability of burning minor actinides and long lived fission products (FPs) without imposing penalties on core nuclear and safety characteristics. The excess neutrons generated in the fast reactor core are fully utilized not only to generate the fissile material but also to transmute the minor actinides and long lived FPs. The FP target assemblies which consist of Tc-99 and I-129 are loaded into the selected blanket positions whereas the minor actinides are loaded to the rest of the blanket. A long term FP accumulation scenario is also considered in the mix of FP burner fast reactor and non-burner LWRs. (author)

A review of the demonstration of innovative solvent extraction processes for the recovery of trivalent minor actinides from PUREX raffinate

International Nuclear Information System (INIS)

Modolo, G.; Wilden, A.; Geist, A.; Magnusson, D.; Malmbeck, R.

2012-01-01

The selective partitioning (P) of long-lived minor actinides from highly active waste solutions and their transmutation (T) to short-lived or stable isotopes by nuclear reactions will reduce the long-term hazard of the high-level waste and significantly shorten the time needed to ensure their safe confinement in a repository. The present paper summarizes the on-going research activities at Forschungszentrum Juelich (FZJ), Karlsruher Institut fuer Technologie (KIT) and Institute for Transuranium Elements (ITU) in the field of actinide partitioning using innovative solvent extraction processes. European research over the last few decades, i.e. in the NEWPART, PARTNEW and EUROPART programmes, has resulted in the development of multi-cycle processes for minor actinide partitioning. These multi-cycle processes are based on the co-separation of trivalent actinides and lanthanides (e.g. by the DIAMEX process), followed by the subsequent actinide(III)/lanthanide(III) group separation in the SANEX process. The current direction of research for the development of innovative processes within the recent European ACSEPT project is discussed additionally. This paper is focused on the development of flow-sheets for recovery of americium and curium from highly active waste solutions. The flow-sheets are verified by demonstration processes, in centrifugal contactors, using synthetic or genuine fuel solutions. The feasibility of the processes is also discussed. (orig.)

Special actinide nuclides: Fuel or waste?

International Nuclear Information System (INIS)

Srinivasan, M.; Rao, K.S.; Dingankar, M.V.

1989-01-01

The special actinide nuclides such as Np, Cm, etc. which are produced as byproducts during the operation of fission reactors are presently looked upon as 'nuclear waste' and are proposed to be disposed of as part of high level waste in deep geological repositories. The potential hazard posed to future generations over periods of thousands of years by these long lived nuclides has been a persistent source of concern to critics of nuclear power. However, the authors have recently shown that each and every one of the special actinide nuclides is a better nuclear fuel than the isotopes of plutonium. This finding suggests that one does not have to resort to exotic neutron sources for transmuting/incinerating them as proposed by some researchers. Recovery of the special actinide elements from the waste stream and recycling them back into conventional fission reactors would eliminate one of the stigmas attached to nuclear energy

Short-lived radionuclides produced on the ORNL 86-inch cyclotron and High-Flux Isotope Reactor

International Nuclear Information System (INIS)

Lamb, E.

1985-01-01

The production of short-lived radionuclides at ORNL includes the preparation of target materials, irradiation on the 86-in. cyclotron and in the High Flux Isotope Reactor (HFIR), and chemical processing to recover and purify the product radionuclides. In some cases the target materials are highly enriched stable isotopes separated on the ORNL calutrons. High-purity 123 I has been produced on the 86-in. cyclotron by irradiating an enriched target of 123 Te in a proton beam. Research on calutron separations has led to a 123 Te product with lower concentrations of 124 Te and 126 Te and, consequently to lower concentrations of the unwanted radionuclides, 124 I and 126 I, in the 123 I product. The 86-in. cyclotron accelerates a beam of protons only but is unique in providing the highest available beam current of 1500 μA at 21 MeV. This beam current produces relatively large quantities of radionuclides such as 123 I and 67 Ga

Partitioning and Transmutation of minor actinides

International Nuclear Information System (INIS)

Koch, L.; Wellum, R.

1991-01-01

The partitioning of minor actinides from spent fuels and their transmutation into short-lived fission products has been the topic of two dedicated meetings organized jointly by the European Commission and the OECD. The conclusion of the last meeting in 1980, in short, was that partitioning and transmutation of minor actinides, especially in fast reactors, seemed possible. However, the incentive, which would be a reduction of the radiological hazard to the public, was too small if long-lived fission products were not included. Furthermore this meeting showed that minor actinide targets or possible nuclear fuels containing minor actinides for transmutation had not yet been developed. The European Institute for Transuranium Elements took up this task and has carried it out as a small activity for several years. Interests expressed recently by an expert meeting of the OECD/NEA (Paris, 25 April 1989), which was initiated by the proposed Japanese project Omega, led us to the conclusion that the present state of knowledge should be looked at in a workshop environment. Since the Japanese proposal within the project Omega is based on a broader approach we needed this evaluation to assess the relevance of our present activity and wanted to identifiy additional studies which might be needed to cover possible future demands from the public. This workshop was therefore organized, and participants active in the field from EC countries, the USA and Japan were invited

Feasibility studies of actinide recycle in LMFBRs as a waste management alternative

International Nuclear Information System (INIS)

Beaman, S.L.; Aitken, E.A.

1976-01-01

A strategy of actinide burnup in LMFBRs is being investigated as a waste management alternative to long term storage of high level nuclear waste. This strategy is being evaluated because many of the actinides in the waste from spent-fuel reprocessing have half-lives of thousands of years and an alternative to geological storage may be desired. From a radiological viewpoint, the actinides and their daughters dominate the waste hazard for decay times beyond about 400 years. Actinide burnup in LMFBRs may be an attractive alternative to geological storage because the actinides can be effectively transmuted to fission products which have significantly shorter half-lives. Actinide burnup in LMFBRs rather than LWRs is preferred because the ratio of fission reaction rate to capture reaction rate for the actinides is higher in an LMFBR, and an LMFBR is not so sensitive to the addition of the actinide isotopes. An actinide target assembly recycle scheme is evaluated to determine the effects of the actinides on the LMFBR performance, including local power peaking, breeding ratio, and fissile material requirements. Several schemes are evaluated to identify any major problems associated with reprocessing and fabrication of recycle actinide-containing assemblies. The overall efficiency of actinide burnout in LMFBRs is evaluated, and equilibrium cycle conditions are determined. It is concluded that actinide recycle in LMFBRs offers an attractive alternative to long term storage of the actinides, and does not significantly affect the performance of the host LMFBR. Assuming a 0.1 percent or less actinide loss during reprocessing, a 0.1 percent loss of less during fabrication, and proper recycle schemes, virtually all of the actinides produced by a fission reactor economy could be transmuted in fast reactors

Minor actinide transmutation using minor actinide burner reactors

International Nuclear Information System (INIS)

Mukaiyama, T.; Yoshida, H.; Gunji, Y.

1991-01-01

The concept of minor actinide burner reactor is proposed as an efficient way to transmute long-lived minor actinides in order to ease the burden of high-level radioactive waste disposal problem. Conceptual design study of minor actinide burner reactors was performed to obtain a reactor model with very hard neutron spectrum and very high neutron flux in which minor actinides can be fissioned efficiently. Two models of burner reactors were obtained, one with metal fuel core and the other with particle fuel core. Minor actinide transmutation by the actinide burner reactors is compared with that by power reactors from both the reactor physics and fuel cycle facilities view point. (author)

Neutron-induced cross sections of short-lived nuclei via the surrogate reaction method

Directory of Open Access Journals (Sweden)

Morel P.

2011-10-01

Full Text Available The measurement of neutron-induced cross sections of short-lived nuclei is extremely difficult due to the radioactivity of the samples. The surrogate reaction method is an indirect way of determining cross sections for nuclear reactions that proceed through a compound nucleus. This method presents the advantage that the target material can be stable or less radioactive than the material required for a neutron-induced measurement. We have successfully used the surrogate reaction method to extract neutron-induced fission cross sections of various short-lived actinides. In this work, we investigate whether this technique can be used to determine neutron-induced capture cross sections in the rare-earth region.

Neutron-induced cross sections of short-lived nuclei via the surrogate reaction method

Directory of Open Access Journals (Sweden)

Tassan-Got L.

2012-02-01

Full Text Available The measurement of neutron-induced cross sections of short-lived nuclei is extremely difficult due to the radioactivity of the samples. The surrogate reaction method is an indirect way of determining cross sections for nuclear reactions that proceed through a compound nucleus. This method presents the advantage that the target material can be stable or less radioactive than the material required for a neutron-induced measurement. We have successfully used the surrogate reaction method to extract neutron-induced fission cross sections of various short-lived actinides. In this work, we investigate whether this technique can be used to determine neutron-induced capture cross sections in the rare-earth region.

CANDU - a versatile reactor for plutonium disposition or actinide burning

International Nuclear Information System (INIS)

Chan, P.S.W.; Gagnon, M.J.N.; Boczar, P.G.; Ellis, R.J.; Verrall, R.A.

1997-10-01

High neutron economy, on-line refuelling, and a simple fuel-bundle design result in a high degree of versatility in the use of the CANDU reactor for the disposition of weapons-derived plutonium and for the annihilation of long-lived radioactive actinides, such as plutonium, neptunium, and americium isotopes, created in civilian nuclear power reactors. Inherent safety features are incorporated into the design of the bundles carrying the plutonium and actinide fuels. This approach enables existing CANDU reactors to operate with various plutonium-based fuel cycles without requiring major changes to the current reactor design. (author)

Rapid determination of actinides in seawater samples

International Nuclear Information System (INIS)

Maxwell, S.L.; Culligan, B.K.; Hutchison, J.B.; Utsey, R.C.; McAlister, D.R.

2014-01-01

A new rapid method for the determination of actinides in seawater samples has been developed at the Savannah River National Laboratory. The actinides can be measured by alpha spectrometry or inductively-coupled plasma mass spectrometry. The new method employs novel pre-concentration steps to collect the actinide isotopes quickly from 80 L or more of seawater. Actinides are co-precipitated using an iron hydroxide co-precipitation step enhanced with Ti +3 reductant, followed by lanthanum fluoride co-precipitation. Stacked TEVA Resin and TRU Resin cartridges are used to rapidly separate Pu, U, and Np isotopes from seawater samples. TEVA Resin and DGA Resin were used to separate and measure Pu, Am and Cm isotopes in seawater volumes up to 80 L. This robust method is ideal for emergency seawater samples following a radiological incident. It can also be used, however, for the routine analysis of seawater samples for oceanographic studies to enhance efficiency and productivity. In contrast, many current methods to determine actinides in seawater can take 1-2 weeks and provide chemical yields of ∼30-60 %. This new sample preparation method can be performed in 4-8 h with tracer yields of ∼85-95 %. By employing a rapid, robust sample preparation method with high chemical yields, less seawater is needed to achieve lower or comparable detection limits for actinide isotopes with less time and effort. (author)

Research needs in metabolism and dosimetry of the actinides

International Nuclear Information System (INIS)

Richmond, C.R.

1978-01-01

The following topics are discussed: uranium mine and mill tailings; environmental standards; recommendations of NCRP and ICRP; metabolic models and health effects; life-time exposures to actinides and other alpha emitters; high-specific-activity actinide isotopes versus naturally occurring isotopic mixtures of uranium isotopes; adequacy of the n factor; and metabolism and dosimetry;

Actinides burnup in a sodium fast reactor

Energy Technology Data Exchange (ETDEWEB)

Ramirez S, J. R.; Pineda A, R.; Martinez C, E.; Alonso, G., E-mail: ramon.ramirez@inin.gob.mx [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

2017-09-15

The burnup of actinides in a nuclear reactor is been proposed as part of an advanced nuclear fuel cycle, this process would close the fuel cycle recycling some of the radioactive material produced in the open nuclear fuel cycle. These actinides are found in the spent nuclear fuel from nuclear power reactors at the end of their burnup in the reactor. Previous studies of actinides recycling in thermal reactors show that would be possible reduce the amounts of actinides at least in 50% of the recycled amounts. in this work, the amounts of actinides that can be burned in a fast reactor is calculated, very interesting results surge from the calculations, first, the amounts of actinides generated by the fuel is higher than for thermal fuel and the composition of the actinides vector is different as in fuel for thermal reactor the main isotope is the {sup 237}Np in the fuel for fast reactor the main isotope is the {sup 241}Am, finally it is concluded that the fast reactor, also generates important amounts of waste. (Author)

Possibilities of chemical isolation of element 106 from aqueous solutions according to the model experiments with short lived tungsten isotopes

International Nuclear Information System (INIS)

Szeglowski, Z.; Bruchertseifer, H.; Brudanin, V.B.

1993-01-01

A rapid method for continuous separation of short-lived tungsten isotopes from the lanthanides has been developed. It consists in transforming nuclear reaction products from the target by an aerosol jet to an absorber where the KCl particulates are dissolved in 0.2 M HF and percolating the product solution through three successively linked columns filled with ion exchange resins Dowex 50X8 (cationite), Dowex 1X8 (anionite) and again Dowex 50X8. 3 refs

Selective Separation of Trivalent Actinides from Lanthanides by Aqueous Processing with Introduction of Soft Donor Atoms

International Nuclear Information System (INIS)

Nash, Kenneth L.; Clark, Sue B.; Lumetta, Gregg

2009-01-01

With increased application of MOX fuels and longer burnup times for conventional fuels, higher concentrations of the transplutonium actinides Am and Cm (and even heavier species like Bk and Cf) will be produced. The half-lives of the Am isotopes are significantly longer than those of the most important long-lived, high specific activity lanthanides or the most common Cm, Bk and Cf isotopes, thus the greatest concern as regards long-term radiotoxicity. With the removal and transmutation of Am isotopes, radiation levels of high level wastes are reduced to near uranium mineral levels within less than 1000 years as opposed to the time-fram if they remain in the wastes.

The dose from actinides in the environment

International Nuclear Information System (INIS)

Harley, Naomi H.; Pasternack, Bernard S.

1978-01-01

We attempt to evaluate the health effects on local populations from the nuclear power industry. The nuclides which are thought to be most hazardous are the long-lived, alpha-emitting isotopes of plutonium, americium and curium. These long-lived alpha emitters will almost certainly be dispersed in the environment during fuel reprocessing. Their effect is local, not global and at worst a single community could be affected. The most important pathway for exposure to the actinides is through inhalation following resuspension of contaminated soil particles. The most important alpha dose estimates are to cells in bronchial epithelium and cells on bone surfaces. These alpha dose estimates are calculated for a dispersal which contaminates soil with 1 pCi/g of each of the nuclides Pu 238,239 , Am 241 , Cm 242,244 . These bronchial and bone cell dose estimates are compared with those from the naturally occurring actinide 232 Th (and daughters) which are normally found in soil at a level of about 1 pCi/g. (author)

Actinide partitioning-transmutation program final report. III. Transmutation studies

International Nuclear Information System (INIS)

Wachter, J.W.; Croff, A.G.

1980-07-01

Transmutation of the long-lived nuclides contained in fuel cycle wastes has been suggested as a means of reducing the long-term toxicity of the wastes. A comprehensive program to evaluate the feasibility and incentives for recovering the actinides from wastes (partitioning) and transmuting them to short-lived or stable nuclides has been in progress for 3 years under the direction of Oak Ridge National Laboratory (ORNL). This report constitutes the final assessment of transmutation in support of this program. Included are (1) a summary of recent transmutation literature, (2) a generic evaluation of actinide transmutation in thermal, fast, and other transmutation devices, (3) a preliminary evaluation of 99 Tc and 129 I transmutation, and (4) a characterization of a pressurized-water-reactor fuel cycle with and without provisions for actinide recovery and transmutation for use in other parts of the ORNL program. The principal conclusion of the report is that actinide transmutation is feasible in both thermal and fast reactors, subject to demonstrating satisfactory fuel performance, with relatively little impact on the reactor. It would also appear that additional transmutation studies are unwarranted until a firm decision to proceed with actinide transmutation has been made by the responsible authorities

New data on some short-lived isotopes of ruthenium and rhodium

International Nuclear Information System (INIS)

Baumgartner, F.; Plata Bedmar, A.

1961-01-01

Ru and Rd isotopes with mass numbers 107 and 108 and 1 09Rh, has been obtained from fission products. 1 07 Ru has also been prepared by the nuclear process 1 10Pd (n,α) 1 07 Ru. Beta and gamma energies of these nuclides have been studied spectropolarimetry and the gamma lines found for 1 07 Ru and 1 08Ru ( and daughter) have been very useful for the precise determination of their half-lives. 1 09Rh has been identified through its daughter 1 09Pd in the mixture of rhodium isotopes from fission products. Irradiation of natural palladium with fast neutrons has lead to an activity that may only be attributed to 1 10rh. Neither its half life nor its decay energy have been possible to determine accurately. (Author) 1 refs

A Summary of Actinide Enrichment Technologies and Capability Gaps

Energy Technology Data Exchange (ETDEWEB)

Patton, Bradley D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Robinson, Sharon M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-01-01

The evaluation performed in this study indicates that a new program is needed to efficiently provide a national actinide radioisotope enrichment capability to produce milligram-to-gram quantities of unique materials for user communities. This program should leverage past actinide enrichment, the recent advances in stable isotope enrichment, and assessments of the future requirements to cost effectively develop this capability while establishing an experience base for a new generation of researchers in this vital area. Preliminary evaluations indicate that an electromagnetic isotope separation (EMIS) device would have the capability to meet the future needs of the user community for enriched actinides. The EMIS technology could be potentially coupled with other enrichment technologies, such as irradiation, as pre-enrichment and/or post-enrichment systems to increase the throughput, reduce losses of material, and/or reduce operational costs of the base EMIS system. Past actinide enrichment experience and advances in the EMIS technology applied in stable isotope separations should be leveraged with this new evaluation information to assist in the establishment of a domestic actinide radioisotope enrichment capability.

Half-lives for selected actinides and long-lived radionuclides

International Nuclear Information System (INIS)

Holden, N.E.

1988-01-01

Long-lived actinide nuclides are of interest for their use in nuclear reactors, for nuclear reactor burnup studies in waste management, and for safeguard applications, e.g., α counting is used to determine the amount of material present. Some long-lived radionuclides are of interest for their use in determining geological ages using various dating methods, and in calculating the cosmic-ray exposure ages of meteorites. Recommended values are presented for both the total half-life and for the spontaneous fission half-life of /sup 232-236,238/U, of /sup 236,238-242,244/Pu, of /sup 241,242m,243/Am, and of /sup 242-248,250/Cm. Problems with the presentation of uncertainties are discussed. The impact of the revised 14 C half-life on the carbon dating technique and various 14 C ages is discussed. The possible primordial occurrence of 92 Nb is now definitely ruled out. Based on examination of the 26 Al half-life, the calculated value for the cosmic-ray exposure age of meteorites remains too high compared to the age calculated using other radionuclide half-life values. 204 Pb, which was once thought to be radioactive, is shown to be stable. 37 refs., 5 tabs

Research on activation analysis using short-lived isotopes and a multi-purpose isotopic neutron irradiator. Part of a coordinated programme on on-line X-ray and neutron techniques for industrial process control

International Nuclear Information System (INIS)

Ozek, F.

1981-02-01

A method of cyclic activation analysis (CA) has been studied and applied. A theoretical comparison between cyclic and conventional neutron activation analysis of gold has been made. The optimum number of cycles in cyclic activation have been investigated and an equation for the rapid calculation of the number of cycles is proposed. The isotopic neutron irradiation system including the 5Ci Pu-Be neutron source was designed and constructed. The system is flexible and transportable and is capable of carrying out prompt and conventional delay gamma-ray analysis and cyclic activation of bulk materials. The advantages as well as the disadvantages of neutron activation analysis with the use of short-lived nuclides were considered, and can be summarized as follows: Advantages: saturation factor approaches unity, speed of analysis, low cost of analysis, increased selectivity, reduced matrix activities. Disadvantages: proximity of neutron source, chemical separation hardly possible or impossible, total number of counts low. Low counting rates can be substantially increased by applying the technique of ''cyclic activation'', which is another reason by the use of short-lived isotopes in neutron activation analysis is steadily becoming more attractive

Citrate-based open-quotes Talspeakclose quotes actinide-lanthanide separation process

International Nuclear Information System (INIS)

Del Cul, G.D.; Toth, L.M.; Bond, W.D.

1997-01-01

Lanthanide elements are produced in relatively high yield by fission of 235 U. Almost all the lanthanide isotopes decay to stable nonradioactive lanthanide isotopes in a relatively short time. Consequently, it is highly advantageous to separate the relatively small actinide fraction from the relatively large quantities of lanthanide isotopes. The TALSPEAK process (Trivalent Actinide Lanthanide Separations by Phosphorus-reagent Extraction from Aqueous Complexes) is one of the few means available to separate the trivalent actinides from the lanthanides. Previous work based on the use of lactic or glycolic acid has shown deleterious effects of some impurity ions such as zirconium(IV), even at concentrations on the order of 10 -4 M. Other perceived problems were the need to maintain the pH and reagent concentrations within a narrow range and a significant solubility of the organic phase at high carboxylic acid concentrations. The authors' cold experiments showed that replacing the traditional extractants glycolic or lactic acid with citric acid eliminates or greatly reduces the deleterious effects produced by impurities such as zirconium. An extensive series of batch tests was done using a wide range of reagent concentrations at different pH values, temperatures, and contact times. The results demonstrated that the citrate-based TALSPEAK can tolerate appreciable changes in pH and reagent concentrations while maintaining an adequate lanthanide extraction. Experiments using a three-stage glass mixer-settler showed a good lanthanide extraction, appropriate phase disengagement, no appreciable deleterious effects due to the presence of impurities such as zirconium, excellent pH buffering, and no significant loss of organic phase

Nuclear transmutation of actinides other than fuel as a radioactive waste management scheme

International Nuclear Information System (INIS)

Cecille, L.; Hage, W.; Hettinger, H.; Mannone, F.; Mousty, F.; Schmidt, E.; Sola, A.; Huber, B.; Koch, L.

1977-01-01

The bulk of fission products in the high-level waste (HLW) decays to innocuous hazard levels within about 600 years. Actinide waste and a few fission products however represent a potential risk up to some hundreds of thousand of years. An alternative to the disposal of the whole HLW in geological formations is its fractionation, a nuclear transmutation of long-lived isotopes in fission reactors and a geological disposal of the other components. This solution would decrease the potential long-term risks of the geological waste disposal and would also accomodate to the demand of public opinion. The results of studies related to this management scheme are outlined with special reference to areas, where additional effort is required for realistic cost/benefit evaluations. Reactor physics calculations demonstrated the feasibility of actinide incineration in thermal and fast reactors. Obtained transmutation rates are sufficiently high to garantee acceptably small actinide inventories in the reactor in the case of self-generated actinide recycling. It appears that fast breeders could be used as transmutation devices without major additional reactor devlopment work. The thermal power rating of actinide fuel elements and the contribution of actinides and of minor amounts of lanthanide impurities to the neutron economy of the reactor has been evaluated. Sensitivity studies indicated that the results are dependent on the reactor operation mode and on the accuracy of the nuclear data. These calculations permitted the identification of isotopes for which cross section masurements and improved theoretical methods are required. The chemical separation of actinides from the HLW with the envisaged decontamination factors is being studied by solvent extraction and precipitation techniques using waste simulates and samples of high activity waste from European reprocessing plants. Up to now, the obtained results do not yet allow a definitive judgement on the feasibility of actinides

AMS of actinides in ground- and seawater: a new procedure for simultaneous analysis of U, Np, Pu, Am and Cm isotopes below ppq levels

Energy Technology Data Exchange (ETDEWEB)

Quinto, Francesca; Lagos, Markus; Plaschke, Markus; Schaefer, Thorsten; Geckeis, Horst [Institut fuer Nukleare Entsorgung, KIT, Eggenstein-Leopoldshafen (Germany); Steier, Peter [VERA Laboratory, University of Vienna, Vienna (Austria)

2015-07-01

U-236, Np-237, Pu isotopes and Am-243 were determined in ground- and seawater samples at levels below ppq with a maximum sample size of 0.250 l. Such high sensitivity measurement was possible by using accelerator mass spectrometry (AMS) with an improved gas stripping and an additional high resolving magnet. The use of non-isotopic tracers was investigated in order to allow the determination of those nuclides, namely Np-237 and Am-243, for which isotopic tracers for mass spectrometry are rarely available. The actinides were concentrated from the sample matrix via iron hydroxide co-precipitation and measured sequentially without previous chemical separation from each other. The analytical method was validated with the analysis of IAEA 443 seawater Reference Material and applied to background samples from the Colloid Formation and Migration project at the Grimsel Test Site and to sea- and freshwater samples affected solely by global fallout. The sensitivity of the presented analytical method provides the capability to study the long-term release of actinide tracers in field experiments as well as the transport of actinides in a variety of environmental systems.

Isotopes a very short introduction

CERN Document Server

Ellam, Rob

2016-01-01

An isotope is a variant form of a chemical element, containing a different number of neutrons in its nucleus. Most elements exist as several isotopes. Many are stable while others are radioactive, and some may only exist fleetingly before decaying into other elements. In this Very Short Introduction, Rob Ellam explains how isotopes have proved enormously important across all the sciences and in archaeology. Radioactive isotopes may be familiar from their use in nuclear weapons, nuclear power, and in medicine, as well as in carbon dating. They have been central to establishing the age of the Earth and the origins of the solar system. Combining previous and new research, Ellam provides an overview of the nature of stable and radioactive isotopes, and considers their wide range of modern applications. ABOUT THE SERIES: The Very Short Introductions series from Oxford University Press contains hundreds of titles in almost every subject area. These pocket-sized books are the perfect way to get ahead in a new subjec...

Production and measurement of minor actinides in the commercial fuel cycle

International Nuclear Information System (INIS)

Stanbro, W.D.

1997-03-01

The minor actinide elements, particularly neptunium and americium, are produced as a normal byproduct of the operation of thermal power reactors. Because of the existence of long-lived isotopes of these elements, they constitute the major sources of the residual radiation in spent fuel or in wastes resulting from reprocessing. This has led to examinations by some countries of the possibility of separating the minor actinides from waste products. The papers found in this report address the production of minor actinides in common thermal power reactors as well as approaches to measure these materials in various media. The first paper in this volume, open-quotes Production of Minor Actinides in the Commercial Fuel Cycle,close quotes uses calculations with the ORIGEN2 reactor and decay code to estimate the amounts of minor actinides in spent fuel and separated plutonium as a function of reactor irradiation and the time after discharge. The second paper, open-quotes Destructive Assay of Minor Actinides,close quotes describes a number of promising approaches for the chemical analysis of minor actinides in the various forms in which they are found at reprocessing plants. The next paper, open-quotes Hybrid KED/XRF Measurement of Minor Actinides in Reprocessing Plants,close quotes uses the results of a simulation model to examine the possible applications of the hybrid KED/XRF instrument to the determination of minor actinides in some of the solutions found in reprocessing plants. In open-quotes Calorimetric Assay of Minor Actinides,close quotes the authors show some possible extensions of this powerful technique beyond the normal plutonium assays to include the minor actinides. Finally, the last paper in this volume, open-quotes Environment Measurements of Transuranic Nuclides,close quotes discusses what is known about the levels of the minor actinides in the environment and ways to analyze for these materials in environmental matrices

High flux transmutation of fission products and actinides

International Nuclear Information System (INIS)

Gerasimov, A.; Kiselev, G.; Myrtsymova, L.

2001-01-01

Long-lived fission products and minor actinides accumulated in spent nuclear fuel of power reactors comprise the major part of high level radwaste. Their incineration is important from the point of view of radwaste management. Transmutation of these nuclides by means of neutron irradiation can be performed either in conventional nuclear reactors, or in specialized transmutation reactors, or in ADS facilities with subcritical reactor and neutron source with application of proton accelerator. Different types of transmutation nuclear facilities can be used in order to insure optimal incineration conditions for radwaste. The choice of facility type for optimal transmutation should be based on the fundamental data in the physics of nuclide transformations. Transmutation of minor actinides leads to the increase of radiotoxicity during irradiation. It takes significant time compared to the lifetime of reactor facility to achieve equilibrium without effective transmutation. High flux nuclear facilities allow to minimize these draw-backs of conventional facilities with both thermal and fast neutron spectrum. They provide fast approach to equilibrium and low level of equilibrium mass and radiotoxicity of transmuted actinides. High flux facilities are advantageous also for transmutation of long-lived fission products as they provide short incineration time

Determination of actinides using ICP-SFMS

International Nuclear Information System (INIS)

Nygren, Ulrika

2006-01-01

Interest in the determination of the actinides using ICP-MS has steadily increased with the development of systems capable of more sensitive and precise measurements. However, the analysis of less abundant actinides such as Pu and Am is not straightforward due to the need for chemical separation of these elements prior to determination. In many applications of mass-spectrometric actinide analysis, isotope ratio measurements are important, either for the analysis of the isotopic composition of, e.g., U or Pu in the sample, or for quantitative determinations using isotope dilution mass spectrometry. In order to achieve high precision and accuracy in an isotope ratio measurement, corrections for instrumentally induced systematic errors, e.g., due to dead-time and mass bias, need to be considered. In this thesis, different aspects of actinide analysis using ICP-SFMS have been addressed. In Papers I and III, separation procedures based on solid phase extraction for Pu, Am and U were developed and evaluated with respect to chemical yield and separation from elements causing spectral interferences. Applications of the analytical procedures developed comprised measurement of the 240 Pu/ 2 3 9Pu ratio in environmental reference materials, and age determination of Pu based on the 241 Pu/ 241 Am and 240 Pu/ 236 U ratios. In the application of different separation procedures for Pu, previously unidentified spectral interferences were discovered. In Paper II, these interferences were identified as lanthanide phosphate ions and the composition and formation of these species with respect to different instrumental parameters were further examined. Due to the importance of precise and accurate isotope ratio determination, a thorough investigation of the instrumental dead time of an ICP-SFMS system was performed. The dead time was evaluated via both isotope ratio and electronic measurements of the output from the detector amplifier. It was found that the overall uncertainty in ratio

Short-lived medical isotopes at Harwell

International Nuclear Information System (INIS)

Cuninghame, J.G.

1985-01-01

This paper describes the small program of medical isotope commercial production and research and development on the Harwell Variable Energy Cyclotron. Because of its complexity, this nuclear research machine is extremely expensive to run, and so the program must be restricted to those isotopes which cannot be more cheaply produced elsewhere in the United Kingdom. At present these are 123 I (in full commercial production), the /sup 195m/Hg → /sup 195m/Au generator (about to go into commercial production), and 211 At (under development). Iodine-123 is produced once or twice a week at a level of 300 to 400 mCi per batch and is sold to an average of 30 customers all over the United Kingdom and Europe. The gold generator is being developed for first-pass heart angiography and is undergoing clinical trials at three U.K. hospitals. A research program in conjunction with the U.K. Medical Research Council is directed to the labeling of monoclonal antibodies with 211 At as a possible agent for cancer therapy

The Lawrence Livermore National Laboratory Intelligent Actinide Analysis System

International Nuclear Information System (INIS)

Buckley, W.M.; Carlson, J.B.; Koenig, Z.M.

1993-01-01

The authors have developed an Intelligent Actinide Analysis System (IAAS) for Materials Management to use in the Plutonium Facility at the Lawrence Livermore National Laboratory. The IAAS will measure isotopic ratios for plutonium and other actinides non-destructively by high-resolution gamma-ray spectrometry. This system will measure samples in a variety of matrices and containers. It will provide automated control of many aspects of the instrument that previously required manual intervention and/or control. The IAAS is a second-generation instrument, based on experience in fielding gamma isotopic systems, that is intended to advance non-destructive actinide analysis for nuclear safeguards in performance, automation, ease of use, adaptability, systems integration and extensibility to robotics. It uses a client-server distributed monitoring and control architecture. The IAAS uses MGA as the isotopic analysis code. The design of the IAAS reduces the need for operator intervention, operator training, and operator exposure

Studies on short-lived fission products at the Mainz TRIGA reactor

International Nuclear Information System (INIS)

Trautmann, N.

1974-01-01

Neutron-rich nuclei of medium mass number are produced by thermal-neutron-induced fission of heavy elements, e.g., 235 U, 239 Pu, and 249 Cf. Pulse irradiations lead to an enhancement of the ratio of short-lived activities to the accompanying longer-lived components. One approach for investigating the properties of short-lived nuclei consists in a combination of rapid chemical separations with higher-resolution gamma spectroscopy. This is demonstrated by the isolation of neutron-rich isotopes of niobium by sorption on glass and of ruthenium by solvent extraction. Other rapid separation procedures from aqueous solutions are briefly summarized and a few examples for their application in nuclear fission- and delayed neutron studies are given. Some experiments with an on-line mass separator of the ISOLDE-type, using chemical targets, are described. (U.S.)

Continuous administration of short-lived isotopes for evaluating dynamic parameters

International Nuclear Information System (INIS)

Selikson, M.

1985-01-01

In this paper it is shown that continuous but varying infusions (specifically, exponential infusions) of a short-lived radionuclide can be used to evaluate a wide range of dynamic parameters. The detector response to exponential infusions is derived. An example of an inert diffusible substrate for evaluating regional flow and a glucose model for evaluating regional metabolic rate are both worked out. The advantages of using exponential infusion methods are discussed

The future of the accelerator mass spectrometry of rare long-lived radioactive isotopes

International Nuclear Information System (INIS)

Litherland, A.E.

1990-01-01

Accelerators, originally designed for nuclear physics, can be added to mass spectrometric apparatus to increase the sensitivity so that isotope ratios in the range 10 -12 to 10 -15 can be measured routinely. This significant improvement of high-sensitivity mass spectrometry has been called Accelerator Mass Spectrometry. The present article addresses the basic principles of accelerator mass spectrometry and some recent applications which show its versatility. In particular, it is noted that accelerator mass spectrometry could play an increasing role in the measurement of the levels of long lived radioactivities in the environment, including the actinides, which result from human activities such as the use of nuclear power. To fulfill this promise, continued research and development is necessary to provide ion sources, various types of heavy ion accelerators and peripheral magnetic and electric analysers. (N.K.)

Actinide partitioning-transmutation program final report. I. Overall assessment

International Nuclear Information System (INIS)

Croff, A.G.; Blomeke, J.O.; Finney, B.C.

1980-06-01

This report is concerned with an overall assessment of the feasibility of and incentives for partitioning (recovering) long-lived nuclides from fuel reprocessing and fuel refabrication plant radioactive wastes and transmuting them to shorter-lived or stable nuclides by neutron irradiation. The principal class of nuclides considered is the actinides, although a brief analysis is given of the partitioning and transmutation (P-T) of 99 Tc and 129 I. The results obtained in this program permit us to make a comparison of the impacts of waste management with and without actinide recovery and transmutation. Three major conclusions concerning technical feasibility can be drawn from the assessment: (1) actinide P-T is feasible, subject to the acceptability of fuels containing recycle actinides; (2) technetium P-T is feasible if satisfactory partitioning processes can be developed and satisfactory fuels identified (no studies have been made in this area); and (3) iodine P-T is marginally feasible at best because of the low transmutation rates, the high volatility, and the corrosiveness of iodine and iodine compounds. It was concluded on the basis of a very conservative repository risk analysis that there are no safety or cost incentives for actinide P-T. In fact, if nonradiological risks are included, the short-term risks of P-T exceed the long-term benefits integrated over a period of 1 million years. Incentives for technetium and iodine P-T exist only if extremely conservative long-term risk analyses are used. Further RD and D in support of P-T is not warranted

The Lawrence Livermore National Laboratory Intelligent Actinide Analysis System

International Nuclear Information System (INIS)

Buckley, W.M.; Carlson, J.B.; Koenig, Z.M.

1993-07-01

The authors have developed an Intelligent Actinide Analysis System (IAAS) for Materials Management to use in the Plutonium Facility at the Lawrence Livermore National Laboratory. The IAAS will measure isotopic ratios for plutonium and other actinides non-destructively by high-resolution gamma-ray spectrometry. This system will measure samples in a variety of matrices and containers. It will provide automated control of many aspects of the instrument that previously required manual intervention and/or control. The IAAS is a second-generation instrument, based on the authors' experience in fielding gamma isotopic systems, that is intended to advance non-destructive actinide analysis for nuclear safeguards in performance, automation, ease of use, adaptability, systems integration and extensibility to robotics. It uses a client-server distributed monitoring and control architecture. The IAAS uses MGA 3 as the isotopic analysis code. The design of the IAAS reduces the need for operator intervention, operator training, and operator exposure

Actinide partitioning from high level liquid waste using the Diamex process

International Nuclear Information System (INIS)

Madic, C.; Blanc, P.; Condamines, N.; Baron, P.; Berthon, L.; Nicol, C.; Pozo, C.; Lecomte, M.; Philippe, M.; Masson, M.; Hequet, C.

1994-01-01

The removal of long-lived radionuclides, which belong to the so-called minor actinides elements, neptunium, americium and curium, from the high level nuclear wastes separated during the reprocessing of the irradiated nuclear fuels in order to transmute them into short-lived nuclides, can substantially decrease the potential hazards associated with the management of these nuclear wastes. In order to separate minor actinides from high-level liquid wastes (HLLW), a liquid-liquid extraction process was considered, based on the use of diamide molecules, which display the property of being totally burnable, thus they do not generate secondary solid wastes. The main extracting properties of dimethyldibutyltetradecylmalonamide (DMDBTDMA), the diamide selected for the development of the DIAMEX process, are briefly described in this paper. Hot tests of the DIAMEX process (using DMDBTDMA) related to the treatment of an mixed oxide fuels (MOX) type HLLW, were successfully performed. The minor actinide decontamination factors of the HLLW obtained were encouraging. The main results of these tests are presented and discussed in this paper. (authors). 9 refs., 2 figs., 7 tabs

On the hazard accumulation of actinide waste in a Pu-fueled LMFBR power economy with and without by-product actinide recycling

International Nuclear Information System (INIS)

Anselmi, L.; Caruso, K.; Hage, W.; Schmidt, E.

1979-01-01

The actinide waste arisings in terms of hazard potential for ingestion and inhalation are given for a Pu-fueled LMFBR Power Economy as function of decay time. The data were assessed for two simplified fuel cycles, one considering the recycling of by-product actinides and the other their complete discharge to the high-level waste. Two durations of nuclear power and several loss fractions of actinides to the waste were considered. The major contributors in form of chemical elements or isotopes to the actinide waste hazard built up during the nuclear power duration were identified for various decay intervals

Proposal for experiments with actinide elements

International Nuclear Information System (INIS)

Sanchez, R.G.

1994-01-01

An analytical study was conducted in which critical masses for some actinide isotopes were calculated with the Monte Carlo Neutron Photon (MCNP) Transport computer code. Different spherical computer models were used for even- and odd-neutron nuclides. Critical masses obtained are tabulated for Np-237, Pu-242, Am-241, Am-243, Pu-241, and Am-242m, together with indirect experimental data. Experimental data are needed for actinides with odd number of neutrons

Rapid ion-exchange separations of actinides

International Nuclear Information System (INIS)

Usuda, Shigekazu

1988-01-01

For the purpose of studying short-lived actinide nuclides, three methods for rapid ion exchange separation of actinide elements with mineral acid-alcohol mixed media were developed: anion exchange with nitric acid-methyl alcohol mixed media to separate the transplutonium and rare earth elements from target material, U or Pu and Al catcher foils; anion exchange with hydrochloric acid-methyl alcohol media to separate Am+Cm, Bk and Cf+Fm from the target, catcher foils and major fission products; and cation exchange with hydrochloric acid-methyl alcohol media and with concentrated hydrochloric acid to separate the transplutonium elements as a group from the rare earths after eliminating the large amounts of U, Al, Cu, Fe etc. The methods enable one to perform rapid and effective separation at elevated temperature (90 deg C) and immediate source preparation for alpha-ray spectrometry. (author) 47 refs.; 10 figs

Ten years of experience in extraction chromatographic processes for the recovery, separation and purification of actinides elements

International Nuclear Information System (INIS)

Madic, C.; Bourges, J.; Koehly, G.

1984-06-01

Ten years ago the extraction chromatographic technique was developed for preparative purposes and is now applied for all chemicals separations needed for the production of actinides isotopes. That technique appears to be simple and flexible. It can be used for the production of microgram to kilogram amounts of actinide isotopes. This paper focuses on the experience gained and describes some peculiar production of actinide isotopes solved by using extraction chromatographic technique. After a review of extracting molecules and equipment, treatment of irradiated targets (preparation of Pu 238 and removal of neptunium, production of Am 243 and Cm 244), recovery of actinides from alpha aqueous wastes (preparation of Am 241) and recovery of decay products from aged actinide stocks (recovery of Am 241 from Pu stocks, of U 234 from Pu 238 stocks) are described

Hyperfine structure and isotope shift measurements of short-lived elements by laser spectroscopy, January 1-December 31, 1984

International Nuclear Information System (INIS)

Schuessler, H.A.

1983-09-01

Research progress is reported in the areas of stored ion spectroscopy, numerical studies of the trapping of pulse injected ions, beam tests at the TRISTAN mass separator, fluorescence line narrowing technique for Doppler-free observation, observation of the isotope shift on long-lived gold isotopes, and observation of Doppler-free signals in a fast Ar + beam

Research on the chemical speciation of actinides

International Nuclear Information System (INIS)

Jung, Euo Chang; Park, K. K.; Cho, H. R.

2010-04-01

A demand for the safe and effective management of spent nuclear fuel and radioactive waste generated from nuclear power plant draws increasing attention with the growth of nuclear power industry. The objective of this project is to establish the basis of research on the actinide chemistry by using advanced laser-based highly sensitive spectroscopic systems. Researches on the chemical speciation of actinides are prerequisite for the development of technologies related to nuclear fuel cycles, especially, such as the safe management of high level radioactive wastes and the chemical examination of irradiated nuclear fuels. For supporting these technologies, laser-based spectroscopies have been performed for the chemical speciation of actinide in an aqueous solutions and the quantitative analysis of actinide isotopes in spent nuclear fuels. In this report, results on the following subjects have been summarized. (1) Development of TRLFS technology for chemical speciation of actinides, (2) Development of LIBD technology for measuring solubility of actinides, (3) Chemical speciation of plutonium complexes by using a LWCC system, (4) Development of LIBS technology for the quantitative analysis of actinides, (5) Development of technology for the chemical speciation of actinides by CE, (6) Evaluation on the chemical reactions between actinides and humic substances, (7) Chemical speciation of actinides adsorbed on metal oxides surfaces, (8) Determination of actinide source terms of spent nuclear fuel

Use of short-lived radionuclides in the agricultural and environmental sciences

International Nuclear Information System (INIS)

Krohn, K.A.

1985-01-01

In addition to their well-known uses in physiology, biochemistry, and medicine, short-lived radioisotopes have played an important part in promoting the authors knowledge of the agricultural and environmental sciences. Numerous investigators have found that the scientific rewards justify the additional demands associated with use of short-lived radioisotopes when novel or uniquely precise results can be achieved. This is best exemplified by examining the use of 13 N. Nitrogen-13 is the longest lived radioisotope of this very important element. The 10-min half-life of 13 N has required that the agricultural or environmental test model be brought to the laboratory where the isotope is made, but this has been done successfully in numerous instances. One major incentive for this research has probably been the fact that there is no analog of the very useful 14 C tracer to study nitrogen chemistry and biology

Preliminary minimum detectable limit measurements in 208-L drums for selected actinide isotopes in mock-waste matrices

International Nuclear Information System (INIS)

Camp, D.C.; Wang, Tzu-Fang; Martz, H.E.

1992-01-01

Preliminary minimum detectable levels (MDLS) of selected actinide isotopes have been determined in full-scale, 55-gallon drums filled with a range of mock-waste materials from combustibles (0.14 g/CM 3 ) to sand (1.7 g/CM 3 ). Measurements were recorded from 100 to 10,000 seconds with selected actinide sources located in these drums at an edge position, on the center axis of a drum and midway between these two positions. Measurements were also made with a 166 Ho source to evaluate the attenuation of these mock-matrix materials as a function of energy. By knowing where the source activity is located within a drum, our preliminary results show that a simply collimated 90% HPGE detector can differentiate between TRU (>100 nCi/g) and LLW amounts of 239 Pu in only 100s of measurement time and with sufficient accuracy in both low and medium density, low Z materials. Other actinides measured so far include 235 U, 241 Am, and 244 Cm. These measurements begin to establish the probable MDLs achievable in the nondestructive assays of real waste drums when using active and passive CT. How future measurements may differ from these preliminary measurements is also discussed

Reflections on the criticality of special actinide elements

International Nuclear Information System (INIS)

Clayton, E.D.

1987-04-01

During recent years, the list of nuclides known to be capable of supporting a chain reaction has substantially increased. Since the criticality aspects for some of these nuclides differ in important respects from those of the most common fissile nuclides, 235 92 U, and 239 94 Pu, a new term, ''fissible'' was recently proposed in nuclear engineering to help distinguish differences. Activation energies for fission have been calculated for 41 of the actinide isotopes which are grouped according to four types of nuclides, those with even-Z, even-N, odd-Z, odd-N, odd-Z, even-N, and even-Z, odd-N. With the possible exception of 237 92 U, all fissible isotopes listed have even N. The activation energy for fission is less in the case of the even-Z, even-N isotopes, but almost without eception it is the odd-N isotopes that undergo fission with thermal neutrons and which constitute the principal criticality problem. This paper reviews the criticality and fissionability aspects of the fissile and fissible actinide isotopes. The criticality of aqueous mixtures of fissile and fissible isotopes also is briefly discussed, including limits for criticality control

Reflections on the criticality of special actinide elements

International Nuclear Information System (INIS)

Clayton, E.D.

1987-01-01

During recent years, the list of nuclides known to be capable of supporting a chain reaction has substantially increased. Since the criticality aspects for some of these nuclides differ in important respects from those of the most common fissile nuclides, 92 235 U, and 94 239 Pu, a new term, ''fissible'' was recently proposed in nuclear engineering to help distinguish differences. Activation energies for fission have been calculated for 41 of the actinide isotopes which are grouped according to four types of nuclides, those with even-Z and even-N, odd-Z and odd-N, odd-Z and even-N, or even-Z and odd-N. With the possible exception of 92 237 U, all fissible isotopes listed have even N. The activation energy for fission is less in the case of the even-Z and even-N isotopes, but almost without exception it is the odd-N isotopes that undergo fission with thermal neutrons and which constitute the principal criticality problem. This paper reviews the criticality and fissionability aspects of the fissile and fissible actinide isotopes. The criticality of aqueous mixtures of fissile and fissible isotopes also is briefly discussed, including limits for criticality control. (author)

Comparative study of accelerator driven system (ADS) of different transmutation scenarios for actinides in advanced nuclear fuel cycles

International Nuclear Information System (INIS)

Embid-Segura, M.; Gonzalez Romero, M.E.; Perez Parra, A.

2001-01-01

The full text follows. In recent years transmutation has raised as a complementary option to solve the problem of the long-lived radioactive waste produced in nuclear power plants. The main advantages expected from transmutation are the reduction in volume of the high level waste and a significant decrease in the long-term radiotoxicity inventory, with a probable impact in the final costs and potential risks of the geological repository. This paper will describe the evaluation of different systems proposed for actinide transmutation, their integration in the waste management process, their viability, performances and limitations. Particular attention is taking of comparing transmutation scenarios where the actinides are transmuted inside fertile (U, Th) or inert matrix. This study has been supported by ENRESA inside the CIEMAT-ENRESA collaboration for the study of long-lived isotope transmutation. (authors)

Determination of fission products and actinides by inductively coupled plasma-mass spectrometry using isotope dilution analysis. A study of random and systematic errors

International Nuclear Information System (INIS)

Ignacio Garcia Alonso, Jose

1995-01-01

The theory of the propagation of errors (random and systematic) for isotope dilution analysis (IDA) has been applied to the analysis of fission products and actinide elements by inductively coupled plasma-mass spectrometry (ICP-MS). Systematic errors in ID-ICP-MS arising from mass-discrimination (mass bias), detector non-linearity and isobaric interferences in the measured isotopes have to be corrected for in order to achieve accurate results. The mass bias factor and the detector dead-time can be determined by using natural elements with well-defined isotope abundances. A combined method for the simultaneous determination of both factors is proposed. On the other hand, isobaric interferences for some fission products and actinides cannot be eliminated using mathematical corrections (due to the unknown isotope abundances in the sample) and a chemical separation is necessary. The theory for random error propagation in IDA has been applied to the determination of non-natural elements by ICP-MS taking into account all possible sources of uncertainty with pulse counting detection. For the analysis of fission products, the selection of the right spike isotope composition and spike to sample ratio can be performed by applying conventional random propagation theory. However, it has been observed that, in the experimental determination of the isotope abundances of the fission product elements to be determined, the correction for mass-discrimination and the correction for detector dead-time losses contribute to the total random uncertainty. For the instrument used in the experimental part of this study, it was found that the random uncertainty on the measured isotope ratios followed Poisson statistics for low counting rates whereas, for high counting rates, source instability was the main source of error

Optimization of the recoil-shadow projection method for the investigation of short-lived fission isomers

Energy Technology Data Exchange (ETDEWEB)

Helmecke, M.; Thirolf, P.G.; Habs, D.; Gartzke, E.; Kolhinen, V.; Lang, C.; Szerypo, J.; Trepl, L. [Fakultaet f. Physik, LMU Muenchen (Germany); Maier-Leibnitz Laboratory, Garching (Germany)

2009-07-01

Spectroscopic studies of super- and hyperdeformed actinide nuclei offer the possibility to gain insight into the multiple-humped fission barrier landscape. With the identification of deep third minima in {sup 234}U and {sup 236}U the systematics of fission isomers in light actinides was revisited, especially searching for isomers in light uranium isotopes with half-lives in the pico-second range. Using the recoil-shadow projection method and solid state nuclear track detectors, an experimental search for their observation has been started. This well-established detection technique nowadays benefits from an efficient analysis technology based on a PC-controlled auto-focus microscope and a CCD camera together with pattern recognition software. The flatness and the definition of the shadow edge of the target is the critical point of this method: Due to the energy loss of the beam the target carrier foil (1{mu}m Ni) may develop thermal distortions in the {mu}m range, leading to misinterpretations of isomeric fission fragments. Therefore the flatness of the target foil is continuously monitored via a capacitance measurement. First results applying this method to the search of a fission isomer in {sup 234}U via the {sup 232}Th({alpha},2n) reaction are presented.

Quantitative cerebral blood flow patterns with the short lived isotope 195m Au

International Nuclear Information System (INIS)

Lindner, P.; Nickel, O.

1984-01-01

A previously reported theory for quantitative cerebral blood flow measurements using intravenously injected nondiffusible radiotracers has been applied on patients after stroke and on volunteers undergoing a mental stimulation exercise. Quantitative measurements of cerebral blood flow patterns (in ml/min/100g) not only in p.a. but also in lateral views of the brain are possible by using of the short-lived (30 sec) isotope Au 195m. The energy spectrum of the eluate of the generator shows two strong photon peaks, one at 68 keV and a second at 262 keV. The 68 keV peak is suitable for perfusion studies in lateral views of the hemispheres, no 'look through' effect is seen. The 262 keV peak is good for studies in p.a. positions. The studies last less than 1 minute and can be repeated after 3 minutes. Parametric images for quantitative regional cerebral blood flow can be generated. The area of occluded vessels in the case of stroke can be made visible. Quantitative activation patterns of cerebral blood flow during mental stimulation can be generated. After optical stimulation a clear increase of blood flow was seen in the visual cortex. The results prove that not only with freely diffusible (like Xenon) but also with nondiffusible indicators like 195m Au it is possible to measure quantitatively cerebral blood flow patterns. Au 195m is very advantageous for quantitative clinical investigations of cerebrovascular disease. (Author)

Short Lived Fission Product Yield Measurements in 235U, 238U and 239Pu

Science.gov (United States)

Silano, Jack; Tonchev, Anton; Tornow, Werner; Krishichayan, Fnu; Finch, Sean; Gooden, Matthew; Wilhelmy, Jerry

2017-09-01

Yields of short lived fission products (FPYs) with half lives of a few minutes to an hour contain a wealth of information about the fission process. Knowledge of short lived FPYs would contribute to existing data on longer lived FPY mass and charge distributions. Of particular interest are the relative yields between the ground states and isomeric states of FPYs since these isomeric ratios can be used to determine the angular momentum of the fragments. Over the past five years, a LLNL-TUNL-LANL collaboration has made precision measurements of FPYs from quasi-monoenergetic neutron induced fission of 235U, 238U and 239Pu. These efforts focused on longer lived FPYs, using a well characterized dual fission chamber and several days of neutron beam exposure. For the first time, this established technique will be applied to measuring short lived FPYs, with half lives of minutes to less than an hour. A feasibility study will be performed using irradiation times of < 1 hour, improving the sensitivity to short lived FPYs by limiting the buildup of long lived isotopes. Results from this exploratory study will be presented, and the implications for isomeric ratio measurements will be discussed. This work was performed under the auspices of US DOE by LLNL under Contract DE-AC52-07NA27344.

Research on the chemical speciation of actinides

International Nuclear Information System (INIS)

Jung, Euo Chang; Park, K. K.; Cho, H. R.

2012-04-01

A demand for the safe and effective management of spent nuclear fuel and radioactive waste generated from nuclear power plant draws increasing attention with the growth of nuclear power industry. The objective of this project is to establish the basis of research on the actinide chemistry by using highly sensitive and advanced laser-based spectroscopic systems. Researches on the chemical speciation of actinides are prerequisite for the development of technologies related to nuclear fuel cycles, especially, such as the safe management of high level radioactive wastes and the chemical examination of irradiated nuclear fuels. For supporting these technologies, laser-based spectroscopies have been applied for the chemical speciation of actinide in aqueous solutions and the quantitative analysis of actinide isotopes in spent nuclear fuels. In this report, results on the following subjects have been summarized. Development of TRLFS technology for the chemical speciation of actinides, Development of laser-induced photo-acoustic spectroscopy (LPAS) system, Application of LIBD technology to investigate dynamic behaviors of actinides dissolution reactions, Development of nanoparticle analysis technology in groundwater using LIBD, Chemical speciation of plutonium complexes by using a LWCC system, Development of LIBS technology for the quantitative analysis of actinides, Evaluation on the chemical reactions between actinides and humic substances, Spectroscopic speciation of uranium-ligand complexes in aqueous solution, Chemical speciation of actinides adsorbed on metal oxides surfaces

Study of short-lived fission products with the aid of an isotope separator connected to reactor R2-0

International Nuclear Information System (INIS)

Rudstam, G.

1976-01-01

This report constitutes a final report on project 74-3289 together with a preliminary report for project 75-3332. These projects have been included in the budget years 1974/75 and 1975/76 as a contribution to the operating costs of reactor R2-0 at Studsvik. The reactor was used for experimental studies on short-lived fission products with OSIRIS isotope-separator equipment. The scientific programme is very broad. It comprises, in the first place, characterisation of fission products (a study of their excitation levels, measurement of decay properties such as half-life and emission of delayed neutrons, determination of neutron energy spectrum, determination of total decay energy, etc.). An important application of this field of research is the determination of decay heat in nuclear fuel. The programme thus comprises research of a fundamental character and applied research. (H.E.G.)

Search for EC-decayed neutron-deficient actinide isotopes using gas-jet coupled JAERI-ISOL

Energy Technology Data Exchange (ETDEWEB)

Tsukada, Kazuaki [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1997-07-01

To study the nuclear properties of unknown neutron deficient actinide isotopes which decay mainly via orbital electron capture (EC), we have developed a composite system consisting of a gas-jet transport apparatus and a thermal ion-source at the JAERI-ISOL. With this system, search for {sup 236}Am produced in the {sup 235}U({sup 6}Li, 5n) reaction has been performed. Pu KX-rays associated with the EC decay of {sup 236}Am are observed at the mass-236 fraction. The half-life of {sup 236}Am is evaluated to be 4.4min. The outline of the gas-jet coupled JAERI-ISOL system and typical performance are given. (author)

Isotope-dilution mass spectrometry in the measurement of plutonium isotope half-lives

International Nuclear Information System (INIS)

Abernathey, R.M.; Marsh, S.F.

1981-01-01

Isotope-dilution mass spectrometry has been used at Los Alamos to measure the half-lives of 239 Pu, 240 Pu, and 241 Pu. The latter was determined by measuring the rate of decrease of the 241 Pu/ 242 Pu ratio in an appropriate isotopic mixture over a period of several years. The half-lives of the two lighter isotopes are too long to be determined in this manner. They were determined by measuring the rate of production of the uranium daughter relative to a known added 233 U spike. Experimental procedures were designed to control sources of error and to permit a detailed statistical treatment which included all known sources of error and accounted for all covariances. The uncertainties, at the 95% confidence level, associated with the measured half-lives were less than 0.4% for 241 Pu and less than 0.2% for 239 Pu and 240 Pu

Effect of spectral characterization of gaseous fuel reactors on transmutation and burning of actinides

Energy Technology Data Exchange (ETDEWEB)

Fung, C.; Anghaie, S. [Florida Univ., Wilmington, NC (United States)

2007-07-01

Gaseous Core Reactors (GCR) are fueled with stable uranium compounds in a reflected cavity. The spectral characteristics of neutrons in GCR systems could shift from one end of the spectrum to the other end by changing design parameters such as reflector material and thickness, uranium enrichment, and the average operational temperature and pressure. The rate of actinide generation, transmutation, and burnup is highly influenced by the average neutron energy in reactor core. In particular, the production rate and isotopic mix of plutonium are highly dependent on the neutron spectrum in the reactor. Other actinides of primary interest to this work are neptunium-237 and americium-241 due to their pivotal impact on high-level nuclear waste disposal. In all cavity reactors including GCR's, the reflector material and thickness are the most important design parameters in determining the core spectrum. The increase in the gaseous fuel pressure and enrichment results in relative shift of neutron population toward energies greater than 2 eV. Reflector materials considered in this study are beryllium oxide, lithium hydride, lithium deuteride, zirconium carbide, graphite, lead, and tungsten. Results of the study suggest that the beryllium oxide and tungsten reflected GCR systems set the lower (softest) and upper (hardest) limits of neutron spectra, respectively. The inventory of actinides with half-lives greater than 1000 years can be minimized by increasing neutron flux level in the reactor core. The higher the neutron flux, the lower the inventory of these actinides. The majority of the GCR designs maintained a flux level on the order of 10{sup 15} cm{sup -2}*s{sup -1} while the PWR flux is one order of magnitude lower. The inventory of the feeder isotopes to Np{sup 237} including U{sup 237}, Pu{sup 241}, and Am{sup 241} decreases with relative shift of neutron spectrum toward higher energies. This is due to increased resonance absorption in these isotopes due to higher

Geochemistry of long lived transuranic actinides and fission products

International Nuclear Information System (INIS)

1992-01-01

The IAEA initiated in 1987 a new Co-ordinated Research Programme (CRP) on geochemistry of long lived transuranic actinides and fission products for a duration of 5 years. The framework of the CRP consists of three main components: (1) development of a working hypothesis with focus on laboratory studies; (2) testing of the working hypothesis with the focus on the field studies; and (3) transport modelling. The contents of this document reflect the results reported on by a number of Member States who participated in this Co-ordinated Research Programme which investigated the geochemical processes and mechanisms which affect rock-water interactions and migration of the chemical elements in geological media as scientific background in support of safety assessments of repositories for high level radioactive wastes. Studies conducted considered the migration of the long lived radionuclides of Tc, I, Np and Pu in both the near and far field. The programme investigated natural occurrences and geochemical processes and mechanisms which may affect migration of the chemical elements under consideration in geological media which may be used for disposal of radioactive wastes. 47 refs, 9 figs, 1 tab

The investigation of properties of short-lived SF isotopes (Z > 100 at the focal plane of VASSILISSA separator

Directory of Open Access Journals (Sweden)

Svirikhin Alexandr

2013-12-01

Full Text Available For experiments aimed at the study of spontaneous fission of transfermium nuclei improvements in the focal plane detector system of recoil separator VASSILISSA have been made. A neutron detector consisting of 54 3He-filled counters has been mounted around the focal-plane detector chamber. The reaction 48Ca + 206Pb = 2n + 252No is used for tuning the separator settings and calibrating the detector system with the spontaneous fission of the 252No. The average neutron number per 252No spontaneous fission event is as large as ν̅ = 4.06 ± 0.12. The short-lived heavy isotopes 244,246Fm, produced in the complete fusion reactions 40Ar + 206,208Pb, are investigated. The average number of neutrons per spontaneous fission of 244,246Fm from the experimental data were (ν̅ = 3.3 ± 0.3 and (ν̅ = 3.55 ± 0.50, respectively. Both values are determined for the first time.

Comparison of short-lived medical isotopes activation by laser thin target induced protons and conventional cyclotron proton beams

Science.gov (United States)

Murray, Joseph; Dudnikova, Galina; Liu, Tung-Chang; Papadopoulos, Dennis; Sagdeev, Roald; Su, J. J.; UMD MicroPET Team

2014-10-01

Production diagnostic or therapeutic nuclear medicines are either by nuclear reactors or by ion accelerators. In general, diagnostic nuclear radioisotopes have a very short half-life varying from tens of minutes for PET tracers and few hours for SPECT tracers. Thus supplies of PET and SPECT radiotracers are limited by regional production facilities. For example 18F-fluorodeoxyglucose (FDG) is the most desired tracer for positron emission tomography because its 110 minutes half-life is sufficient long for transport from production facilities to nearby users. From nuclear activation to completing image taking must be done within 4 hours. Decentralized production of diagnostic radioisotopes will be idea to make high specific activity radiotracers available to researches and clinicians. 11 C, 13 N, 15 O and 18 F can be produced in the energy range from 10-20 MeV by protons. Protons of energies up to tens of MeV generated by intense laser interacting with hydrogen containing targets have been demonstrated by many groups in the past decade. We use 2D PIC code for proton acceleration, Geant4 Monte Carlo code for nuclei activation to compare the yields and specific activities of short-lived isotopes produced by cyclotron proton beams and laser driven protons.

Measurements of Short-Lived Fission Isomers

Science.gov (United States)

Finch, Sean; Bhike, Megha; Howell, Calvin; Krishichayan, Fnu; Tornow, Werner

2016-09-01

Fission yields of the short lived isomers 134mTe (T1 / 2 = 162 ns) and 136mXe (T1 / 2 = 2 . 95 μs) were measured for 235U and 238U. The isomers were detected by the γ rays associated with the decay of the isomeric states using high-purity germanium detectors. Fission was induced using both monoenergetic γ rays and neutrons. At TUNL's High-Intensity Gamma-ray Source (HI γS), γ rays of 9 and 11 MeV were produced . Monoenergetic 8 MeV neutrons were produced at TUNL's tandem accelerator laboratory. Both beams were pulsed to allow for precise time-gated spectroscopy of both prompt and delayed γ rays following fission. This technique offers a non-destructive probe of special nuclear materials that is sensitive to the isotopic identity of the fissile material.

Disposition of nuclear waste using subcritical accelerator-driven systems

International Nuclear Information System (INIS)

Venneri, F.; Li, N.; Williamson, M.; Houts, M.; Lawrence, G.

1998-01-01

Spent fuel from nuclear power plants contains large quantities of Pu, other actinides, and fission products (FP). This creates challenges for permanent disposal because of the long half-lives of some isotopes and the potential for diversion of the fissile material. Two issues of concern for the US repository concept are: (1) long-term radiological risk peaking tens-of-thousands of years in the future; and (2) short-term thermal loading (decay heat) that limits capacity. An accelerator-driven neutron source can destroy actinides through fission, and can convert long-lived fission products to shorter-lived or stable isotopes. Studies over the past decade have established that accelerator transmutation of waste (ATW) can have a major beneficial impact on the nuclear waste problem. Specifically, the ATW concept the authors are evaluating: (1) destroys over 99.9% of the actinides; (2) destroys over 99.9% of the Tc and I; (3) separates Sr-90 and Cs-137; (4) separates uranium from the spent fuel; (5) produces electric power

Fuel cycle related parametric study considering long lived actinide production, decay heat and fuel cycle performances

International Nuclear Information System (INIS)

Raepsaet, X.; Damian, F.; Lenain, R.; Lecomte, M.

2001-01-01

One of the very attractive HTGR reactor characteristics is its highly versatile and flexible core that can fulfil a wide range of diverse fuel cycles. Based on a GTMHR-600 MWth reactor, analyses of several fuel cycles were carried out without taking into account common fuel particle performance limits (burnup, fast fluence, temperature). These values are, however, indicated in each case. Fuel derived from uranium, thorium and a wide variety of plutonium grades has been considered. Long-lived actinide production and total residual decay heat were evaluated for the various types of fuel. The results presented in this papers provide a comparison of the potential and limits of each fuel cycle and allow to define specific cycles offering lowest actinide production and residual heat associated with a long life cycle. (author)

Surrogate Measurements of Actinide (n,2n) Cross Sections with NeutronSTARS

Energy Technology Data Exchange (ETDEWEB)

Casperson, R. J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Burke, J. T. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hughes, R. O. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Akindele, O. A. [Univ. of California, Berkeley, CA (United States); Koglin, J. D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Wang, B. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Tamashiro, A. [Oregon State Univ., Corvallis, OR (United States)

2016-09-27

Directly measuring (n,2n) cross sections on short-lived actinides presents a number of experimental challenges. The surrogate reaction technique is an experimental method for measuring cross sections on short-­lived isotopes, and it provides a unique solution for measuring (n,2n) cross sections. This technique involves measuring a charged-­particle reaction cross section, where the reaction populates the same compound nucleus as the reaction of interest. To perform these surrogate (n,2n) cross section measurements, a silicon telescope array has been placed along a beam line at the Texas A&M University Cyclotron Institute, which is surrounded by a large tank of gadolinium-doped liquid scintillator, which acts as a neutron detector. The combination of the charge-particle and neutron-detector arrays is referred to as NeutronSTARS. In the analysis procedure for calculating the (n,2n) cross section, the neutron detection efficiency and time structure plays an important role. Due to the lack of availability of isotropic, mono-energetic neutron sources, modeling is an important component in establishing this efficiency and time structure. This report describes the NeutronSTARS array, which was designed and commissioned during this project. It also describes the surrogate reaction technique, specifically referencing a ²³⁵U(n,2n) commissioning measurement that was fielded during the past year. Advanced multiplicity analysis techniques have been developed for this work, which should allow for efficient analysis of ²⁴¹Pu(n,2n) and ²³⁹Pu(n,2n) cross section measurements

From carbon to actinides: A new universal 1MV accelerator mass spectrometer at ANSTO

Science.gov (United States)

Wilcken, K. M.; Hotchkis, M.; Levchenko, V.; Fink, D.; Hauser, T.; Kitchen, R.

2015-10-01

A new 1 MV NEC pelletron AMS system at ANSTO is presented. The spectrometer comprises large radius magnets for actinide measurements. A novel feature of the system is fast switching between isotopes both at low and high energy sections allowing measurements of up to 8 isotopes within a single sequence. Technical details and layout of the spectrometer is presented. Performance data for 14C, 10Be, 26Al and actinides demonstrate the system is ready for routine AMS measurements.

Development of ion beam sputtering techniques for actinide target preparation

Science.gov (United States)

Aaron, W. S.; Zevenbergen, L. A.; Adair, H. L.

1985-06-01

Ion beam sputtering is a routine method for the preparation of thin films used as targets because it allows the use of a minimum quantity of starting material, and losses are much lower than most other vacuum deposition techniques. Work is underway in the Isotope Research Materials Laboratory (IRML) at ORNL to develop the techniques that will make the preparation of actinide targets up to 100 μg/cm 2 by ion beam sputtering a routinely available service from IRML. The preparation of the actinide material in a form suitable for sputtering is a key to this technique, as is designing a sputtering system that allows the flexibility required for custom-ordered target production. At present, development work is being conducted on low-activity actinides in a bench-top system. The system will then be installed in a hood or glove box approved for radioactive materials handling where processing of radium, actinium, and plutonium isotopes among others will be performed.

Internal dose evaluation from actinide intakes during nuclear power reactor spent fuel reprocessing

International Nuclear Information System (INIS)

Pawar, S.K.; Kumar, Ranjeet; Gamre, Rupali; Purohit, R.G.

2011-01-01

Full text: Indian PHWR reactors are using natural uranium as fuel. After use they are discharged from the core and send for fuel reprocessing to extract the unused uranium and plutonium. Plutonium and other actinides are formed by activation of 238 U with neutrons and subsequent decay. During reprocessing of the spent fuel, major long lived actinides (Pu, Am and U) may become radiological safety hazard. Actinides intakes are more probable during declading and chopping of spent fuel. During routine plant operation in reprocessing, exposure to Pu is a major concern along with Am and U in working environment due to its higher radiological hazard and occupational workers are likely to get exposed to plutonium, Americium and Uranium mostly through inhalation. Internally deposited Pu-isotopes, Am-isotope and U-isotopes are estimated using techniques such as lung counting (in-vivo) and urine and faecal bioassay (in-vitro). Evaluation of internal dose of actinides is dependent upon urinary excreted activity. To estimate the internally deposited Pu, U and Am at an intake level of about one ALI (ICRP-78, 1997) of occupational workers, urine bioassay is the preferred technique due to high detection sensitivity, ease of sample handling and economical method. A small and measurable fraction of internally deposited Pu, Am and U are excreted through urine whose content is dependent on time of inhalation, quantity and type of chemical form of inhaled material (S and M class). A standardized radiochemical analysis method for separation and estimation of Pu, Am and U is used to evaluate the urinary excreted activity and internal dose. Several measurements techniques are employed for the estimation of plutonium, Americium and Uranium for example, Alpha Spectrometry, Gamma Spectrometry, Neutron Activation Analysis, Mass Spectrometry and Fission Track Analysis. The radiochemical separation followed by alpha counting and/or spectrometry is chosen due to its ease of handling and

General survey of applications which require actinide nuclear data

International Nuclear Information System (INIS)

Raman, S.

1976-01-01

This review paper discusses the actinide waste problem, the buildup of toxic isotopes in the fuel, the neutron activity associated with irradiated fuel, the 252 Cf buildup problem, and the production of radioisotope power sources as broad areas that require actinide cross-section data. Decay data enter into the area of radiological safety and health physics. This paper also discusses a few cross-section measurements in progress at the Oak Ridge Electron Linear Accelerator. The availability of actinide samples through the Transuranium Program at Oak Ridge is discussed in considerable detail. The present data status with respect to the various applications is reviewed along with recommendations for improving the data base

The actinide beamline - A new AMS facility at ANTARES

International Nuclear Information System (INIS)

Hotchkis, M.A.C.; Lee, P.J.; Mino, N.

1998-01-01

At the ANTARES accelerator a new beamline has been commissioned, incorporating new magnetic and electrostatic analysers, to optimise the efficiency for Actinides detection by Accelerator Mass Spectrometry. The detection of Actinides, particularly the isotopic ratios of uranium and plutonium, provide unique signatures for nuclear safeguards purposes. We are currently engaged in a project to evaluate the application of AMS to the measurement of Actinides in environmental samples for nuclear safeguards. Measurement of 236 U is of particular interest as a means of tracing the anthropogenic component of uranium. 236 U is expected to be present in natural samples at an extremely low level ( 236 U: 238 U ratio ∼10 -10 ). It has recently been demonstrated that AMS has sufficient sensitivity to detect 236 U at this level. The principal components of the new beamline include: an electrostatic quadrupole, a 12 deg electrostatic deflector, a 90 deg electrostatic analyser, a multi-isotope detection system including ion counters and Faraday cups. The beamline was completed in September 1998 and initial tests have been performed with iodine samples

Investigation of short-lived neutron-rich palladium and silver isotopes after fast chemical separation from fission fragments

International Nuclear Information System (INIS)

Bruechle, W.

1976-01-01

In this paper, chemical separation processes are described permitting fast and neat isolation of short-lived palladium and silver nuclides from fusion product mixtures. The process for palladium is based on the stability of palladium diethyldithiophosphate. From fission products of the reactions 238 U(n,f) and 249 Cf(nth,f), the following palladium niclides could be studied for the first time by gamma spectroscopy: 1.66 min 113 Pd, 2.45 min 114 Pd, 29 sec sup(115a)Pd, 54 sec sup(115b)Pd, 12.5 sec 116 Pd. 113 Pd could also be indentified according to the reaction 116 Cd(n,α) 113 Pd. The separation of silver is based on the fast isotopic exchange on AgCl. With this process, the following nuclides have been separated from fission product mixtures and studied by gamma spectroscopy: 70 sec sup(113m)Ag, 5.0 sec 114 Ag, 19.2 sec sup(115m)Ag, 2.65 min sup(116g)Ag, 10.5 sec sup(116m)Ag, 1.3 min sup(117g)Ag, 6.0 sec sup(117m)Ag, 4.0 sec 118 Ag. (orig./WL) [de

Significance of actinide chemistry for the long-term safety of waste disposal

International Nuclear Information System (INIS)

Kim, Jae Il

2006-01-01

A geochemical approach to the long-term safety of waste disposal is discussed in connection with the significance of actinides, which shall deliver the major radioactivity inventory subsequent to the relatively short-term decay of fission products. Every power reactor generates transuranic (TRU) elements: plutonium and minor actinides (Np, Am, Cm), which consist chiefly of long-lived nuclides emitting alpha radiation. The amount of TRU actinides generated in a fuel life period is found to be relatively small (about 1 wt% or less in spent fuel) but their radioactivity persists many hundred thousands years. Geological confinement of waste containing TRU actinides demands, as a result, fundamental knowledge on the geochemical behavior of actinides in the repository environment for a long period of time. Appraisal of the scientific progress in this subject area is the main objective of the present paper. Following the introductory discussion on natural radioactivities, the nuclear fuel cycle is briefly brought up with reference to actinide generation and waste disposal. As the long-term disposal safety concerns inevitably with actinides, the significance of the aquatic actinide chemistry is summarized in two parts: the fundamental properties relevant to their aquatic behavior and the geochemical reactions in nanoscopic scale. The constrained space of writing allows discussion on some examples only, for which topics of the primary concern are selected, e.g. apparent solubility and colloid generation, colloid-facilitated migration, notable speciation of such processes, etc. Discussion is summed up to end with how to make a geochemical approach available for the long-term disposal safety of nuclear waste or for the Performance Assessment (PA) as known generally

Report of the panel on practical problems in actinide biology

International Nuclear Information System (INIS)

Anon.

1978-01-01

Practical problems are classified as the need to make operational decisions, the need for regulatory assessment either of individual facilities or of generic actions, and the overt appearance of radiobiological effects in man or radioactivity in man or the environment. Topics discussed are as follows: simulated reactor accident; long term effects of low doses; effects of repeated exposures to actinides; inhaled uranium mine air contaminants; metabolism and dosimetry; environmental equilibrium models; patterns of alpha dosimetry; internal dose calculations; interfaces between actinide biology and environmental studies; removal of actinides deposited in the body; and research needs related to uranium isotopes

From carbon to actinides: A new universal 1MV accelerator mass spectrometer at ANSTO

Energy Technology Data Exchange (ETDEWEB)

Wilcken, K.M., E-mail: klaus.wilcken@ansto.gov.au [Australian Nuclear Science & Technology Organisation, Sydney, New South Wales (Australia); Hotchkis, M.; Levchenko, V.; Fink, D. [Australian Nuclear Science & Technology Organisation, Sydney, New South Wales (Australia); Hauser, T.; Kitchen, R. [National Electrostatics Corporation, 7540 Graber Road, Middleton, WI 53562-0310 (United States)

2015-10-15

A new 1 MV NEC pelletron AMS system at ANSTO is presented. The spectrometer comprises large radius magnets for actinide measurements. A novel feature of the system is fast switching between isotopes both at low and high energy sections allowing measurements of up to 8 isotopes within a single sequence. Technical details and layout of the spectrometer is presented. Performance data for {sup 14}C, {sup 10}Be, {sup 26}Al and actinides demonstrate the system is ready for routine AMS measurements.

Trace analysis of actinides in the environment using resonance ionization mass spectrometry

International Nuclear Information System (INIS)

Raeder, Sebastian

2011-01-01

In this work the resonant ionization of neutral atoms using laser radiation was applied and optimized for ultra-trace analysis of the actinides thorium, uranium, neptunium and plutonium. The sensitive detection of these actinides is a challange for the monitoring and quantification of radioactive releases from nuclear facilities. Using resonance ionization spectroscopy combined with a newly developed quadrupole-mass-spectrometer, numerous energy levels in the atomic structure of these actinides could be identified. With this knowledge efficient excitation schemes for the mentioned actinides could be identified and characterised. The applied in-source-ionization ensures for a high detection efficiency due to the good overlap of laser radiation with the atomic beam and allows therefore for a low sample consumption which is required for the analysis of radio nuclides. The selective excitation processes in the resonant ionization method supresses unwanted contaminations and was optimized for analytical detection of ultra-trace amounts in environmental samples as well as for determination of isotopic compositions. The efficient in-source-ionization combined with high power pulsed laser radiation allows for detections efficiency up to 1%. For plutonium detection limits in the range of 10 4 -10 5 atoms could be demonstrated for synthetic samples as well as for first environmental samples. The usage of narrow bandwidth continuous wave lasers in combination with a transversal overlap of the laser radiation and the free propagating atomic beam enable for resolving individual isotopic shifts of the resonant transitions. This results in a high selectivity against dominant neighboring isotopes but with a significant loss in detection efficiency. For the ultra-trace isotope 236 U a detection limit down to 10 -9 for the isotope ratio N ( 236 U)/N ( 238 U) could be determined.

Nuclear waste forms for actinides

Science.gov (United States)

Ewing, Rodney C.

1999-01-01

The disposition of actinides, most recently 239Pu from dismantled nuclear weapons, requires effective containment of waste generated by the nuclear fuel cycle. Because actinides (e.g., 239Pu and 237Np) are long-lived, they have a major impact on risk assessments of geologic repositories. Thus, demonstrable, long-term chemical and mechanical durability are essential properties of waste forms for the immobilization of actinides. Mineralogic and geologic studies provide excellent candidate phases for immobilization and a unique database that cannot be duplicated by a purely materials science approach. The “mineralogic approach” is illustrated by a discussion of zircon as a phase for the immobilization of excess weapons plutonium. PMID:10097054

Homogeneous Minor Actinide Transmutation in SFR: Neutronic Uncertainties Propagation with Depletion

International Nuclear Information System (INIS)

Buiron, L.; Plisson-Rieunier, D.

2015-01-01

In the frame of next generation fast reactor design, the minimisation of nuclear waste production is one of the key objectives for current R and D. Among the possibilities studied at CEA, minor actinides multi-recycling is the most promising industrial way achievable in the near-term. Two main management options are considered: - Multi-recycling in a homogeneous way (minor actinides diluted in the driver fuel). If this solution can help achieving high transmutation rates, the negative impact of minor actinides on safety coefficients allows only a small fraction of the total heavy mass to be loaded in the core (∼ few %). - Multi-recycling in heterogeneous way by means of Minor Actinide Bearing Blanket (MABB) located at the core periphery. This solution offers more flexibility than the previous one, allowing a total minor actinides decoupled management from the core fuel. As the impact on feedback coefficient is small larger initial minor actinide mass can be loaded in this configuration. Starting from a breakeven Sodium Fast Reactor designed jointly by CEA, Areva and EdF teams, the so called SFR V2B, transmutation performances have been studied in frame on the French fleet for both options and various specific isotopic management (all minor actinides, americium only, etc.). Using these results, a sensitivity study has been performed to assess neutronic uncertainties (i.e coming from cross section) on mass balance on the most attractive configurations. This work in based on a new implementation of sensitivity on concentration with depletion in the ERANOS code package. Uncertainties on isotopes masses at the end of irradiation using various variance-covariance is discussed. (authors)

Comparison of Time-of-flight and Multicollector ICP Mass Spectrometers for Measuring Actinides in Small Samples using single shot Laser Ablation

International Nuclear Information System (INIS)

R.S. Houk; D.B. Aeschliman; S.J. Bajic; D. Baldwin

2005-01-01

The objective of these experiments is to evaluate the performance of two types of ICP-MS device for measurement of actinide isotopes by laser ablation (LA) ICP-MS. The key advantage of ICP-MS compared to monitoring of radioactive decay is that the element need not decay during the measurement time. Hence ICP-MS is much faster for long-lived radionuclides. The LA process yields a transient signal. When spatially resolved analysis is required for small samples, the laser ablation sample pulse lasts only ∼10 seconds. It is difficult to measure signals at several isotopes with analyzers that are scanned for such a short sample transient. In this work, a time-of-flight (TOF) ICP-MS device, the GBC Optimass 8000 (Figure 1) is one instrument used. Strictly speaking, ions at different m/z values are not measured simultaneously in TOF. However, they are measured in very rapid sequence with little or no compromise between the number of m/z values monitored and the performance. Ions can be measured throughout the m/z range in single sample transients by TOF. The other ICP-MS instrument used is a magnetic sector multicollector MS, the NU Plasma 1700 (Figure 2). Up to 8 adjacent m/z values can be monitored at one setting of the magnetic field and accelerating voltage. Three of these m/z values can be measured with an electron multiplier. This device is usually used for high precision isotope ratio measurements with the Faraday cup detectors. The electron multipliers have much higher sensitivity. In our experience with the scanning magnetic sector instrument in Ames, these devices have the highest sensitivity and lowest background of any ICP-MS device. The ability to monitor several ions simultaneously, or nearly so, should make these devices valuable for the intended application: measurement of actinide isotopes at low concentrations in very small samples for nonproliferation purposes. The primary sample analyzed was an urban dust pellet reference material, NIST 1648. The

Reactor physics aspects of burning actinides in a nuclear reactor

International Nuclear Information System (INIS)

Hage, W.; Schmidt, E.

1978-01-01

A short review of the different recycling strategies of actinides other than fuel treated in the literature, is given along with nuclear data requirements for actinide build-up and transmutation studies. The effects of recycling actinides in a nuclear reactor on the flux distribution, the infinite neutron multiplication factor, the reactivity control system, the reactivity coefficients and the delayed neutron fraction are discussed considering a notional LWR or LMFBR as an Actinide Trasmutaton Reactor. Some operational problems of Actinide Transmutation reactors are mentioned, which are caused by the α-decay heat and the neutron sources of Actinide Target Elements

Transmutation of actinides in power reactors.

Science.gov (United States)

Bergelson, B R; Gerasimov, A S; Tikhomirov, G V

2005-01-01

Power reactors can be used for partial short-term transmutation of radwaste. This transmutation is beneficial in terms of subsequent storage conditions for spent fuel in long-term storage facilities. CANDU-type reactors can transmute the main minor actinides from two or three reactors of the VVER-1000 type. A VVER-1000-type reactor can operate in a self-service mode with transmutation of its own actinides.

Nuclear physics with use of KUR. Reviews of 30 years studies on short-lived nuclei and perspectives for the future

International Nuclear Information System (INIS)

Kawase, Yoichi

1995-01-01

The research works which were carried out over the past 30 years on nuclear structure study have been reviewed with emphasis on the technical developments of experimental apparatus for the studies of very short-lived isotopes produced by the Kyoto University reactor(KUR). In the first chapter, nuclear structure studies of neutron-rich nuclei with use of the on-line irradiation apparatus and the on-line isotope separator(ISOL) for fission products have been described. In the second chapter, applications of nuclear methods to solid state physics by the perturbed angular correlation(PAC) technique have been examined to investigate the local electromagnetic fields in metals and compounds through the hyperfine interactions. Perspectives for the future of related research fields are given aiming at the advanced uses of short-lived radioisotopes. (author)

Strongly Enhanced Low Energy Alpha-Particle Decay in Heavy Actinide Nuclei and Long-Lived Superdeformed and Hyperdeformed Isomeric States

CERN Document Server

Marinov, Amnon; Kolb, D.; Weil, J.L.

2001-01-01

Relatively low energy and very enhanced alpha-particle groups have been observed in various actinide fractions produced via secondary reactions in a CERN W target which had been irradiated with 24-GeV protons. In particular, 5.14, 5.27 and 5.53 MeV alpha-particle groups with corresponding half-lives of 3.8(+ -)1.0 y, 625(+ -)84 d and 26(+ -)7 d, have been seen in Bk, Es and Lr-No sources, respectively. The measured energies are a few MeV lower than the known g.s. to g.s. alpha-decays in the corresponding neutron-deficient actinide nuclei. The half-lives are 4 to 7 orders of magnitude shorter than expected from the systematics of alpha-particle decay in this region of nuclei. The deduced evaporation residue cross sections are in the mb region, about 4 orders of magnitude higher than expected. A consistent interpretation of the data is given in terms of production of long-lived isomeric states in the second and third wells of the potential-energy surfaces of the parent nuclei, which decay to the corresponding w...

Innovative SANEX process for trivalent actinides separation from PUREX raffinate

International Nuclear Information System (INIS)

Sypula, Michal

2013-01-01

Recycling of nuclear spent fuel and reduction of its radiotoxicity by separation of long-lived radionuclides would definitely help to close the nuclear fuel cycle ensuring sustainability of the nuclear energy. Partitioning of the main radiotoxicity contributors followed by their conversion into short-lived radioisotopes is known as partitioning and transmutation strategy. To ensure efficient transmutation of the separated elements (minor actinides) the content of lanthanides in the irradiation targets has to be minimised. This objective can be attained by solvent extraction using highly selective ligands that are able to separate these two groups of elements from each other. The objective of this study was to develop a novel process allowing co-separation of minor actinides and lanthanides from a high active acidic feed solution with subsequent actinide recovery using just one cycle, so-called innovative SANEX process. The conditions of each step of the process were optimised to ensure high actinide separation efficiency. Additionally, screening tests of several novel lipophilic and hydrophilic ligands provided by University of Twente were performed. These tests were aiming in better understanding the influence of the extractant structural modifications onto An(III)/Ln(III) selectivity and complexation properties. Optimal conditions for minor actinides separation were found and a flow-sheet of a new innovative SANEX process was proposed. Tests using a single centrifugal contactor confirmed high Eu(III)/Am(III) separation factor of 15 while the lowest SF Ln/Am obtained was 6,5 (for neodymium). In addition, a new masking agent for zirconium was found as a substitution for oxalic acid. This new masking agent (CDTA) was also able to mask palladium without any negative influence on An(III)/Ln(III). Additional tests showed no influence of CDTA on plutonium present in the feed solution unlike oxalic acid which causes Pu precipitation. Therefore, CDTA was proposed as a Zr

Innovative SANEX process for trivalent actinides separation from PUREX raffinate

Energy Technology Data Exchange (ETDEWEB)

Sypula, Michal

2013-07-01

Recycling of nuclear spent fuel and reduction of its radiotoxicity by separation of long-lived radionuclides would definitely help to close the nuclear fuel cycle ensuring sustainability of the nuclear energy. Partitioning of the main radiotoxicity contributors followed by their conversion into short-lived radioisotopes is known as partitioning and transmutation strategy. To ensure efficient transmutation of the separated elements (minor actinides) the content of lanthanides in the irradiation targets has to be minimised. This objective can be attained by solvent extraction using highly selective ligands that are able to separate these two groups of elements from each other. The objective of this study was to develop a novel process allowing co-separation of minor actinides and lanthanides from a high active acidic feed solution with subsequent actinide recovery using just one cycle, so-called innovative SANEX process. The conditions of each step of the process were optimised to ensure high actinide separation efficiency. Additionally, screening tests of several novel lipophilic and hydrophilic ligands provided by University of Twente were performed. These tests were aiming in better understanding the influence of the extractant structural modifications onto An(III)/Ln(III) selectivity and complexation properties. Optimal conditions for minor actinides separation were found and a flow-sheet of a new innovative SANEX process was proposed. Tests using a single centrifugal contactor confirmed high Eu(III)/Am(III) separation factor of 15 while the lowest SF{sub Ln/Am} obtained was 6,5 (for neodymium). In addition, a new masking agent for zirconium was found as a substitution for oxalic acid. This new masking agent (CDTA) was also able to mask palladium without any negative influence on An(III)/Ln(III). Additional tests showed no influence of CDTA on plutonium present in the feed solution unlike oxalic acid which causes Pu precipitation. Therefore, CDTA was proposed as

Determination of minor actinides fission cross sections by means of transfer reactions

Energy Technology Data Exchange (ETDEWEB)

Jurado, B.; Aiche, M.; Barreau, G.; Boyer, S.; Czajkowski, S.; Dassie, D.; Grosjean, C.; Guiral, A.; Haas, B.; Osmanov, B.; Petit, M. [CENBG - UMR 5795 CNRS/IN2P3-Univ. Bordeaux 1- Le Haut Vigneau, 33175 Gradignan (France); Berthoumieux, E.; Gunsing, F.; Perrot, L.; Theisen, Ch. [CEN Saclay, DSM/DAPNIA/SPhN, 91191 Gif-sur-Yvette cedex (France); Bauge, E. [CEA, SPhN, BP12 91680 Bruyeres-le-Chatel (France); Michel-Sendis, F. [IPN, 15 rue G. Clemenceau, 91406 Orsay cedex (France); Billebaud, A. [LPSC, 53 Avenue des Martyrs, 38026 Grenoble cedex (France); Wilson, J. N. [IPN, 15 rue G. Clemenceau, 91406 Orsay cedex (France); LPSC, 53 Avenue des Martyrs, 38026 Grenoble cedex (France); Ahmad, I.; Greene, J.P.; Janssens, R. V. F. [ANL, 9700 S. Cass Avenue, Argonne, IL 60439 (United States)

2005-07-01

We present an original method that allows to determine neutron-induced cross sections of very short-lived minor actinides. This indirect method, based on the use of transfer reactions, has already been applied with success for the determination of the neutron-induced fission and capture cross section of {sup 233}Pa, a key nucleus in the {sup 232}Th - {sup 233}U fuel cycle. A recent experiment using this technique has been performed to determine the neutron-induced fission cross sections of {sup 242,243,244}Cm and {sup 241}Am which are present in the nuclear waste of the current U-Pu fuel cycle. These cross sections are highly relevant for the design of reactors capable to incinerate minor actinides. The first results will be illustrated. (authors)

Subsurface Biogeochemistry of Actinides

Energy Technology Data Exchange (ETDEWEB)

Kersting, Annie B. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States). Univ. Relations and Science Education; Zavarin, Mavrik [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States). Glenn T. Seaborg Inst.

2016-06-29

A major scientific challenge in environmental sciences is to identify the dominant processes controlling actinide transport in the environment. It is estimated that currently, over 2200 metric tons of plutonium (Pu) have been deposited in the subsurface worldwide, a number that increases yearly with additional spent nuclear fuel (Ewing et al., 2010). Plutonium has been shown to migrate on the scale of kilometers, giving way to a critical concern that the fundamental biogeochemical processes that control its behavior in the subsurface are not well understood (Kersting et al., 1999; Novikov et al., 2006; Santschi et al., 2002). Neptunium (Np) is less prevalent in the environment; however, it is predicted to be a significant long-term dose contributor in high-level nuclear waste. Our focus on Np chemistry in this Science Plan is intended to help formulate a better understanding of Pu redox transformations in the environment and clarify the differences between the two long-lived actinides. The research approach of our Science Plan combines (1) Fundamental Mechanistic Studies that identify and quantify biogeochemical processes that control actinide behavior in solution and on solids, (2) Field Integration Studies that investigate the transport characteristics of Pu and test our conceptual understanding of actinide transport, and (3) Actinide Research Capabilities that allow us to achieve the objectives of this Scientific Focus Area (SFA and provide new opportunities for advancing actinide environmental chemistry. These three Research Thrusts form the basis of our SFA Science Program (Figure 1).

Design of unique pins for irradiation of higher actinides in a fast reactor

International Nuclear Information System (INIS)

Basmajian, J.A.; Birney, K.R.; Weber, E.T.; Adair, H.L.; Quinby, T.C.; Raman, S.; Butler, J.K.; Bateman, B.C.; Swanson, K.M.

1982-03-01

The actinides produced by transmutation reactions in nuclear reactor fuels are a significant factor in nuclear fuel burnup, transportation and reprocessing. Irradiation testing is a primary source of data of this type. A segmented pin design was developed which provides for incorporation of multiple specimens of actinide oxides for irradiation in the UK's Prototype Fast Reactor (PFR) at Dounreay Scotland. Results from irradiation of these pins will extend the basic neutronic and material irradiation behavior data for key actinide isotopes

Utilization of plutonium in HTGR and its actinide production

International Nuclear Information System (INIS)

Karin, S.; Brogli, R.; Lefler, W.; Nordheim, L.

1976-01-01

The HTGR is a potential plutonium consumer. In this function it would burn plutonium, produce electricity and the valuable fissile isotope U-233. The advantages of this concept are discussed but particular attention is given to the production and the destruction of the higher actinides due to the high burnup achievable in such a system. The presence of the strong resonances in the plutonium isotopes demanded an extension of the methods for evaluation of self-shielding factors, a different structure for broad groups, and the adaptation of the reactor codes to these changes. Specifications for coated plutonium particles were developed. Also procedures were determined to evaluate the alpha ray and neutron emission rates of the actinide nuclides. First cycle calculations were carried out to establish in detail the characteristics of the plutonium reactors and their results are given

NEW METHOD FOR DETERMINATION OF ACTINIDES AND STRONTIUM IN ANIMAL TISSUE

Energy Technology Data Exchange (ETDEWEB)

Maxwell, S; Jay Hutchison, J; Don Faison, D

2007-05-07

The analysis of actinides in animal tissue samples is very important for environmental monitoring. There is a need to measure actinide isotopes with very low detection limits in animal tissue samples, including fish, deer, hogs, beef and shellfish. A new, rapid actinide separation method has been developed and implemented that allows the measurement of plutonium, neptunium, uranium, americium, curium and strontium isotopes in large animal tissue samples (100-200 g) with high chemical recoveries and effective removal of matrix interferences. This method uses stacked TEVA Resin{reg_sign}, TRU Resin{reg_sign} and DGA-Resin{reg_sign} cartridges from Eichrom Technologies (Darien, IL, USA) that allows the rapid separation of plutonium (Pu), neptunium (Np), uranium (U), americium (Am), and curium (Cm) using a single multi-stage column combined with alpha spectrometry. Sr-90 is collected on Sr Resin{reg_sign} from Eichrom Technologies (Darien, IL, USA). After acid digestion and furnace heating of the animal tissue samples, the actinides and Sr-89/90 are separated using column extraction chromatography. This method has been shown to be effective over a wide range of animal tissue matrices. By using vacuum box cartridge technology with rapid flow rates, sample preparation time is minimized.

Vehicle emissions of short-lived and long-lived climate forcers: trends and tradeoffs.

Science.gov (United States)

Edwards, Morgan R; Klemun, Magdalena M; Kim, Hyung Chul; Wallington, Timothy J; Winkler, Sandra L; Tamor, Michael A; Trancik, Jessika E

2017-08-24

Evaluating technology options to mitigate the climate impacts of road transportation can be challenging, particularly when they involve a tradeoff between long-lived emissions (e.g., carbon dioxide) and short-lived emissions (e.g., methane or black carbon). Here we present trends in short- and long-lived emissions for light- and heavy-duty transport globally and in the U.S., EU, and China over the period 2000-2030, and we discuss past and future changes to vehicle technologies to reduce these emissions. We model the tradeoffs between short- and long-lived emission reductions across a range of technology options, life cycle emission intensities, and equivalency metrics. While short-lived vehicle emissions have decreased globally over the past two decades, significant reductions in CO 2 will be required by mid-century to meet climate change mitigation targets. This is true regardless of the time horizon used to compare long- and short-lived emissions. The short-lived emission intensities of some low-CO 2 technologies are higher than others, and thus their suitability for meeting climate targets depends sensitively on the evaluation time horizon. Other technologies offer low intensities of both short-lived emissions and CO 2 .

Synergistic extraction of actinides : Part I. Hexa-and pentavalent actinides

International Nuclear Information System (INIS)

Patil, S.K.; Ramakrishna, V.V.

1980-01-01

A detailed discussion on the reported literature on the synergistic extraction of hexa- and pentavalent actinide ions, by different combinations of extractants and from different aqueous media, is presented. Structural aspects of the various complexes involved in synergism also are reviewed. A short account of the applications based on synergistic extraction is also given. (author)

Quantitative assessment of the brain perfusion using the short-lived isotope 195m-Au

International Nuclear Information System (INIS)

Lindner, P.; Nickel, O.

1985-01-01

The possibilities of quantitatively assessing the brain perfusion on the basis of a modified transit time theory, using the favourable properties of the ultrashort-lived isotope 195m-Au, are shown. The intravascular deposition of the isotope 195m-Au enables quantitative brain perfusion studies based on both the dorsal and lateral projection. The 195m-Au isotope has a half-life of 30 sec and is able to be eluated from the 195m-Hg 195m-Au generator (Byk-Mallinckrodt). The quantification of brain perfusion (in terms of ml/min/100 g) is based on a recently published theory for non-diffusing radio-indicators, using a first-pass technique. This method of quantification corresponds to a modification of the transit time theory from Maier and Zierler (1) and accounts for the influences of dispersion and recirculation of an intravenously injected non-diffused tracer bolus (2, 3). The energy spectrum of the eluate from the generator shows two lines of high intensity at 262 keV and 68 keV. The low-energy peak is suited for the lateral view, i.e. brain perfusion studies of one hemisphere, without a significant 'look-through-effect'. The high-energy peak is successfully used for dorsal projections of brain perfusion studies. An examination takes less time than one minute and can be repeated after three minutes. Dynamic brain perfusion studies enable parametric images of the quantitative regional brain perfusion distribution, or the reciprocal mean transit times, to be obtained by calculation. Infarcted areas are able to be visualized with high sensitivity. Quantitative perfusion patterns during activation of the visual centre are detectable. The advantages of this method are discussed. (orig.) [de

Physics studies of higher actinide consumption in an LMR

International Nuclear Information System (INIS)

Hill, R.N.; Wade, D.C.; Fujita, E.K.; Khalil, H.

1990-01-01

The core physics aspects of the transuranic burning potential of the integral Fast Reactor (IFR) are assessed. The actinide behavior in fissile self-sufficient IFR closed cycles of 1200 MWt size is characterized, and the transuranic isotopics and risk potential of the working inventory are compared to those from a once-through LWR. The core neutronic performance effects of rare-earth impurities present in the recycled fuel are addressed. Fuel cycle strategies for burning transuranics from an external source are discussed, and specialized actinide burner designs are described

Physics studies of higher actinide consumption in an LMR

International Nuclear Information System (INIS)

Hill, R.N.; Wade, D.C.; Fujita, E.K.; Khalil, H.S.

1990-01-01

The core physics aspects of the transuranic burning potential of the Integral Fast Reactor (IFR) are assessed. The actinide behavior in fissile self-sufficient IFR closed cycles of 1200 MWt size is characterized, and the transuranic isotopics and risk potential of the working inventory are compared to those from a once-through LWR. The core neutronic performance effects of rare-earth impurities present in the recycled fuel are addressed. Fuel cycle strategies for burning transuranics from an external source are discussed, and specialized actinide burner designs are described. 4 refs., 4 figs., 3 tabs

AMS detection of actinides at high mass separation

Energy Technology Data Exchange (ETDEWEB)

Steier, Peter; Lachner, Johannes; Priller, Alfred; Winkler, Stephan; Golser, Robin [University of Vienna, Faculty of Physics, Vienna (Austria); Eigl, Rosmarie [Hiroshima University, Earth and Planetary Systems Science, Hiroshima (Japan); Quinto, Francesca [Institut fuer Nukleare Entsorgung, KIT, Eggenstein-Leopoldshafen (Germany); Sakaguchi, Aya [University of Tsukuba, Center for Research in Isotopes and Environmental Dynamics, Tsukuba (Japan)

2015-07-01

AMS is the mass spectrometric method with the highest abundance sensitivity, which is a prerequisite for measurement of the long-lived radioisotope {sup 236}U (t{sub 1/2}=23.4 million years). The most successful application so far is oceanography, since anthropogenic {sup 236}U is present in the world oceans at {sup 236}U:{sup 238}U from 10{sup -11} to 10{sup -8}. We have explored methods to increase the sensitivity and thus to reduce the water volume required to 1 L or less, which significantly reduces the sampling effort. High sensitivity is also necessary to address the expected typical natural isotopic ratios on the order {sup 236}U:{sup 238}U = 10{sup -13}, with potential applications in geology. With a second 90 analyzer magnet and a new Time-of-Flight beam line, VERA is robust against chemical impurities in the background, which e.g. allows measuring Pu isotopes directly in a uranium matrix. This simplifies chemical sample preparation for actinide detection, and may illustrate why AMS reaches lower detection limits than other mass spectrometric methods with nominally higher detection efficiency.

Benchmark Evaluation of Dounreay Prototype Fast Reactor Minor Actinide Depletion Measurements

Energy Technology Data Exchange (ETDEWEB)

Hess, J. D.; Gauld, I. C.; Gulliford, J.; Hill, I.; Okajima, S.

2017-01-01

Historic measurements of actinide samples in the Dounreay Prototype Fast Reactor (PFR) are of interest for modern nuclear data and simulation validation. Samples of various higher-actinide isotopes were irradiated for 492 effective full-power days and radiochemically assayed at Oak Ridge National Laboratory (ORNL) and Japan Atomic Energy Research Institute (JAERI). Limited data were available regarding the PFR irradiation; a six-group neutron spectra was available with some power history data to support a burnup depletion analysis validation study. Under the guidance of the Organisation for Economic Co-Operation and Development Nuclear Energy Agency (OECD NEA), the International Reactor Physics Experiment Evaluation Project (IRPhEP) and Spent Fuel Isotopic Composition (SFCOMPO) Project are collaborating to recover all measurement data pertaining to these measurements, including collaboration with the United Kingdom to obtain pertinent reactor physics design and operational history data. These activities will produce internationally peer-reviewed benchmark data to support validation of minor actinide cross section data and modern neutronic simulation of fast reactors with accompanying fuel cycle activities such as transportation, recycling, storage, and criticality safety.

Actinide partitioning-transmutation program final report. VI. Short-term risk analysis of reprocessing, refabrication, and transportation: appendix

International Nuclear Information System (INIS)

Fullwood, R.R.; Jackson, R.

1980-01-01

The Chemical Technology Division of the Oak Ridge National Laboratory has prepared a set of documents that evaluate a Partitioning-Transmutation (PT) fuel cycle relative to a Reference cycle employing conventional fuel-material recovery methods. The PT cycle uses enhanced recovery methods so that most of the long-lived actinides are recycled to nuclear power plants and transmuted to shorter-lived materials, thereby reducing the waste toxicity. This report compares the two fuel cycles on the basis of the short-term radiological and nonradiological risks they present to the public and to workers. The accidental radiological risk to the public is analyzed by estimating the probabilities of sets of accidents; the consequences are calculated using the CRAC code appropriately modified for the material composition. Routine radiological risks to the public are estimated from the calculated release amounts; the effects are calculated using the CRAC code. Radiological occupational risks are determined from prior experience, projected standards, and estimates of accident risk. Nonradiological risks are calculated from the number of personnel involved, historical experience, and epidemiological studies. The result of this analysis is that the short-term risk of PT is 2.9 times greater than that of the Reference cycle, primarily due to the larger amount of industry. This conclusion is strongly dominated by the nonradiological risk, which is about 150 times greater than the radiological risk. The absolute risk as estimated for the fuel cycle portions considered in this report is 0.91 fatalities/GWe-year for the PT cycle and 0.34 fatalities/GWe-year for the Reference cycle. This should be compared with Inhaber's estimate of 1.5 for nuclear and 150 for coal. All of the risks assumed here are associated with the production of one billion watts of electricity (GWe) per year

Actinide partitioning-transmutation program final report. VI. Short-term risk analysis of reprocessing, refabrication, and transportation: appendix

Energy Technology Data Exchange (ETDEWEB)

Fullwood, R.R.; Jackson, R.

1980-01-01

The Chemical Technology Division of the Oak Ridge National Laboratory has prepared a set of documents that evaluate a Partitioning-Transmutation (PT) fuel cycle relative to a Reference cycle employing conventional fuel-material recovery methods. The PT cycle uses enhanced recovery methods so that most of the long-lived actinides are recycled to nuclear power plants and transmuted to shorter-lived materials, thereby reducing the waste toxicity. This report compares the two fuel cycles on the basis of the short-term radiological and nonradiological risks they present to the public and to workers. The accidental radiological risk to the public is analyzed by estimating the probabilities of sets of accidents; the consequences are calculated using the CRAC code appropriately modified for the material composition. Routine radiological risks to the public are estimated from the calculated release amounts; the effects are calculated using the CRAC code. Radiological occupational risks are determined from prior experience, projected standards, and estimates of accident risk. Nonradiological risks are calculated from the number of personnel involved, historical experience, and epidemiological studies. The result of this analysis is that the short-term risk of PT is 2.9 times greater than that of the Reference cycle, primarily due to the larger amount of industry. This conclusion is strongly dominated by the nonradiological risk, which is about 150 times greater than the radiological risk. The absolute risk as estimated for the fuel cycle portions considered in this report is 0.91 fatalities/GWe-year for the PT cycle and 0.34 fatalities/GWe-year for the Reference cycle. This should be compared with Inhaber's estimate of 1.5 for nuclear and 150 for coal. All of the risks assumed here are associated with the production of one billion watts of electricity (GWe) per year.

Evaluation of actinide partitioning and transmutation

International Nuclear Information System (INIS)

1982-01-01

After a few centuries of radioactive decay the long-lived actinides, the elements of atomic numbers 89-103, may constitute the main potential radiological health hazard in nuclear wastes. This is because all but a very few fission products (principally technetium-99 and iodine-129) have by then undergone radioactive decay to insignificant levels, leaving the actinides as the principal radionuclides remaining. It was therefore at first sight an attractive concept to recycle the actinides to nuclear reactors, so as to eliminate them by nuclear fission. Thus, investigations of the feasibility and potential benefits and hazards of the concept of 'actinide partitioning and transmutation' were started in numerous countries in the mid-1970s. This final report summarizes the results and conclusions of technical studies performed in connection with a four-year IAEA Co-ordinated Research Programme, started in 1976, on the ''Environmental Evaluation and Hazard Assessment of the Separation of Actinides from Nuclear Wastes followed by either Transmutation or Separate Disposal''. Although many related studies are still continuing, e.g. on waste disposal, long-term safety assessments, and waste actinide management (particularly for low and intermediate-level wastes), some firm conclusions on the overall concept were drawn by the programme participants, which are reflected in this report

Value of burnup credit beyond actinides

International Nuclear Information System (INIS)

Lancaster, D.; Fuentes, E.; Kang, Chi.

1997-01-01

DOE has submitted a topical report to the NRC justifying burnup credit based only on actinide isotopes (U-234, U-235, U-236, U-238, Pu-238, Pu-239, Pu-240, Pu-241, Pu-242, and Am-241). When this topical report is approved, it will allow a great deal of the commercial spent nuclear fuel to be transported in significantly higher capacity casks. A cost savings estimate for shipping fuel in 32 assembly (burnup credit) casks as opposed to 24 assembly (non-burnup credit) casks was previously presented. Since that time, more detailed calculations have been performed using the methodology presented in the Actinide-Only Burnup Credit Topical Report. Loading curves for derated casks have been generated using actinide-only burnup credit and are presented in this paper. The estimates of cost savings due to burnup credit for shipping fuel utilizing 32, 30, 28, and 24 assembly casks where only the 24 assembly cask does not burnup credit have been created and are discussed. 4 refs., 2 figs

Measurement of actinide neutron cross sections

International Nuclear Information System (INIS)

Firestone, Richard B.; Nitsche, Heino; Leung, Ka-Ngo; Perry, DaleL.; English, Gerald

2003-01-01

The maintenance of strong scientific expertise is critical to the U.S. nuclear attribution community. It is particularly important to train students in actinide chemistry and physics. Neutron cross-section data are vital components to strategies for detecting explosives and fissile materials, and these measurements require expertise in chemical separations, actinide target preparation, nuclear spectroscopy, and analytical chemistry. At the University of California, Berkeley and the Lawrence Berkeley National Laboratory we have trained students in actinide chemistry for many years. LBNL is a leader in nuclear data and has published the Table of Isotopes for over 60 years. Recently, LBNL led an international collaboration to measure thermal neutron capture radiative cross sections and prepared the Evaluated Gamma-ray Activation File (EGAF) in collaboration with the IAEA. This file of 35, 000 prompt and delayed gamma ray cross-sections for all elements from Z=1-92 is essential for the neutron interrogation of nuclear materials. LBNL has also developed new, high flux neutron generators and recently opened a 1010 n/s D+D neutron generator experimental facility

Production and Use of Short-Lived Radioisotopes from Reactors. Vol. II. Proceedings of a Seminar on the Practical Applications of Short-Lived Radioisotopes Produced in Small Research Reactors

International Nuclear Information System (INIS)

1963-01-01

There are many radioisotope applications in which it is important that the radiation should rapidly fall to an insignificant level once the initial intense activity has served its purpose. Such applications include diagnostic tests in medicine, where it is essential to reduce the radiation dose to the patient to a minimum, non-destructive testing methods which must be applied without contaminating the material or product concerned, and repeated routine tests which are possible only if the residual activity from the previous test is negligible. All these applications call for radionuclides whose half- lives are measured in hours or even minutes. Similarly, in the new but increasingly important technique of activation analysis, whereby the quantities of elements present in a material can be determined by irradiating the material in a reactor and assaying the radionuclides produced, the latter are mainly short-lived and must be measured immediately. While the production of long-lived radionuclides can most economically be left to the large reactors at the main radioisotope centres, short-lived isotopes must be produced, or materials activation performed, in a reactor at or near the place of intended use or analysis; this, then, represents one of the most important uses for the large number of small reactors which have been installed in recent years, or will come into operation in the near future, in many parts of the world. Since in many countries the new problems of producing, separating and applying short-lived radioisotopes are being faced for the first time, the International Atomic Energy Agency believed it would be valuable to survey the state of the art by convening an international Seminar on Practical Applications of Short-lived Radioisotopes produced in Small Research Reactors at its Vienna headquarters in November, 1962. This Seminar provided an opportunity for the producers and users of short-lived radioisotopes from many countries to meet and discuss the

Production and Use of Short-Lived Radioisotopes from Reactors. Vol. II. Proceedings of a Seminar on the Practical Applications of Short-Lived Radioisotopes Produced in Small Research Reactors

Energy Technology Data Exchange (ETDEWEB)

NONE

1963-03-15

There are many radioisotope applications in which it is important that the radiation should rapidly fall to an insignificant level once the initial intense activity has served its purpose. Such applications include diagnostic tests in medicine, where it is essential to reduce the radiation dose to the patient to a minimum, non-destructive testing methods which must be applied without contaminating the material or product concerned, and repeated routine tests which are possible only if the residual activity from the previous test is negligible. All these applications call for radionuclides whose half- lives are measured in hours or even minutes. Similarly, in the new but increasingly important technique of activation analysis, whereby the quantities of elements present in a material can be determined by irradiating the material in a reactor and assaying the radionuclides produced, the latter are mainly short-lived and must be measured immediately. While the production of long-lived radionuclides can most economically be left to the large reactors at the main radioisotope centres, short-lived isotopes must be produced, or materials activation performed, in a reactor at or near the place of intended use or analysis; this, then, represents one of the most important uses for the large number of small reactors which have been installed in recent years, or will come into operation in the near future, in many parts of the world. Since in many countries the new problems of producing, separating and applying short-lived radioisotopes are being faced for the first time, the International Atomic Energy Agency believed it would be valuable to survey the state of the art by convening an international Seminar on Practical Applications of Short-lived Radioisotopes produced in Small Research Reactors at its Vienna headquarters in November, 1962. This Seminar provided an opportunity for the producers and users of short-lived radioisotopes from many countries to meet and discuss the

Microspheres labelled with short-lived isotopes: Development and application for tumors treatment (Experimental study)

International Nuclear Information System (INIS)

Drozdovsky, B.Y.; Rosiev, R.A.; Goncharova, A.Y.; Skvortsov, V.G.; Petriev, V.M.; Grigoriev, A.N.; Schischkanov, N.G.

1997-01-01

Analysis of the conducted studies strongly suggests the possibility of usage of the domestic protein microspheres as a vehicle for radionuclide. The neutron-activating method of RPP production enables to utilize a broad spectrum of short-living isotopes that can be delivered into the target organ and anchored there for a long time. Good treatment results were obtained in case of the experimentally induced rheumatoid arthritis in rats after intraarticular loading of 165 Dy-hMSA. Mathematical calculations show that homogeneous distribution of RPP in human articulation cavity with the square of 100 cm 2 can be achieved when the quantity of administered particles exceeds 3000. On the example of 165 Dy-hMSA energy characteristic distribution we demonstrated that the absorbed dose for damaged cells at 2mm distance from the radioactive source is 7 times less than the one for a sphere of 2mm diameter. Analysis of dosimetric data in case of intratumoral loading of 165 Dy-hMSA also point out the necessity of the absorbed dose calculation methods taking into account the distance from the source and possible heterogeneity of RPP distribution inside the tumor to be employed. The prolonged RPP detention in the target causing no essential morphological and functional changes was achieved by embolization on the level of septal and interlobular arteries and of efferent arterioles in the animal's renal. The uniformity of microsphere distribution in the organ and their accumulation in tumors depends on the number of particles being administered. Investigations carried out suggest the efficacy of radionuclide therapy application for treatment of oncological and heavy somatic diseases. They also indicate the necessity of further investigations aimed to optimize the usage of microspheres as a radionuclide carrier usage and to work out the criteria of dosimetric planning

Microspheres labelled with short-lived isotopes: Development and application for tumors treatment (Experimental study)

Energy Technology Data Exchange (ETDEWEB)

Drozdovsky, B.Y.; Rosiev, R.A.; Goncharova, A.Y.; Skvortsov, V.G.; Petriev, V.M.; Grigoriev, A.N.; Schischkanov, N.G. [Medical Radiological Research Centre RAMS, Kaluga Region, (Russian Federation)

1997-10-01

Analysis of the conducted studies strongly suggests the possibility of usage of the domestic protein microspheres as a vehicle for radionuclide. The neutron-activating method of RPP production enables to utilize a broad spectrum of short-living isotopes that can be delivered into the target organ and anchored there for a long time. Good treatment results were obtained in case of the experimentally induced rheumatoid arthritis in rats after intraarticular loading of {sup 165}Dy-hMSA. Mathematical calculations show that homogeneous distribution of RPP in human articulation cavity with the square of 100 cm{sup 2} can be achieved when the quantity of administered particles exceeds 3000. On the example of {sup 165}Dy-hMSA energy characteristic distribution we demonstrated that the absorbed dose for damaged cells at 2mm distance from the radioactive source is 7 times less than the one for a sphere of 2mm diameter. Analysis of dosimetric data in case of intratumoral loading of {sup 165}Dy-hMSA also point out the necessity of the absorbed dose calculation methods taking into account the distance from the source and possible heterogeneity of RPP distribution inside the tumor to be employed. The prolonged RPP detention in the target causing no essential morphological and functional changes was achieved by embolization on the level of septal and interlobular arteries and of efferent arterioles in the animal`s renal. The uniformity of microsphere distribution in the organ and their accumulation in tumors depends on the number of particles being administered. Investigations carried out suggest the efficacy of radionuclide therapy application for treatment of oncological and heavy somatic diseases. They also indicate the necessity of further investigations aimed to optimize the usage of microspheres as a radionuclide carrier usage and to work out the criteria of dosimetric planning 25 refs.

Experimental assessment of incineration rates of actinides in high intensity neutron fluxes

International Nuclear Information System (INIS)

Deruelle, O.

2001-01-01

The Mini-inca project develops new experimental facilities and computational methods to carry out integral measurements of actinide transmutation in given irradiation conditions. 2 types of irradiations are foreseen: -) short irradiations to have a precise determination of unknown nuclear parameters such as capture and fission cross sections including branching ratios; -) long irradiations of mono-isotopic sample or known mixtures of isotopes to determine transmutation rates in given high intensity neutron spectra. Irradiations will be carried out in the ILL reactor in Grenoble. A new detection system named Mini-inca chamber has been developed and installed at the ILL reactor, it allows accurate alpha-gamma spectroscopy just after irradiation and even between successive irradiations of the same sample. The advantages of alpha-gamma spectroscopy to determine the composition of the sample are that it is fast, it needs no chemistry and it is non-destructive. The first validation experiments have been performed and their results concerning the irradiation of a Pu-242 target are presented. (A.C.)

Photochemistry of the actinides

International Nuclear Information System (INIS)

Toth, L.M.; Bell, J.T.; Friedman, H.A.

1979-01-01

It has been found that all three major actinides have a useful variety of photochemical reactions which could be used to achieve a separations process that requires fewer reagents. Several features merit enumerating: (1) Laser photochemistry is not now as uniquely important in fuel reprocessing as it is in isotopic enrichment. The photochemistry can be successfully accomplished with conventional light sources. (2) The easiest place to apply photo-reprocessing is on the three actinides U, Pu, and Np. The solutions are potentially cleaner and more amenable to photoreactions. (3) Organic-phase photoreactions are probably not worth much attention because of the troublesome solvent redox chemistry associated with the photochemical reaction. (4) Upstream process treatment on the raffinate (dissolver solution) may never be too attractive since the radiation intensity precludes the usage of many optical materials and the nature of the solution is such that light transmission into it might be totally impossible

Analytical evaluation of actinide sensitivities

International Nuclear Information System (INIS)

Sola, A.

1977-01-01

The analytical evaluation of the sensitivities of actinides to various parameters such as cross sections, decay constants, flux and time is presented. The formulae are applied to isotopes of the Uranium, Neptunium, Plutonium and Americium series. The agreement between analytically obtained and computer evaluated sensitivities being always good, it is throught that the formulation includes all the important parameters entering in the evaluation of sensitivities. A study of the published data is made

New strategy for minor actinides partitioning preliminary results on the electrovolatilization of ruthenium and on the stabilization of Am(IV) in nitric acid with phosphotunsgstate ligand

International Nuclear Information System (INIS)

Adnet, J.M.; Madic, C.

1989-01-01

On problems related to the long term storage in deep geological repositories of high active wastes (H.A.W.) is due to the presence of minor actinide isotopes. Thus after the decay of the fission products (≅ 300 years) the toxicity of these H.A.W. is mainly due to the minor actinides. One solution is based on actinide partitioning followed by transmutation into fission products with short half-lives. A simpler processes than those developed previously, can be based on the possible oxidation of minor actinides to the + IV or + VI oxidation states and their selective extraction. The first step to study is the elimination of the ruthenium (whose presence would be detrimental to oxidize minor actinides) which can be done by electrovolatilization of Ru on the RuO 4 form. The rate of electrovolatilization can be increased by the use of the following electronic mediators, AgI/AgII(1); CeIII/Ce(2), and CoII/CoIII(3), the efficiency of which decreases in the order: 1 > 2 > 3. The effectiveness of that process has been proven when treating real H.A.W solution produced during the study of the reprocessing of a MOX fuel irradiated to as burn-up of 52 GWd/t in a LWR: complete Ru removal was obtained. The second part of the study concerns the electrochemical oxidation of AmIII in nitric acid solutions in the presence of a strong complexing agent: P 2 W 17 O 61 K 10 (P.W.).Total americium oxidation to AmIV can be obtained in nitric acid solution with a concentration up to 8 M. No particular drawback was induced by the presence of an amount of lanthanide III (NdIII) in 6 fold excess vs P.W. The stability of AmIV was studied. The other actinides will be present in these solutions, after the electrochemical oxidation step, in the + VI or+ IV oxidation states, thus a selective extraction (vs fission products) could be performed. A possible way to extract actinide IV/P.W complexes is to use dodecylamine nitrate as extractant

Synthesis of radiopharmaceuticals containing short-lived radionuclides: Comprehensive progress report, March 1, 1986-February 28, 1989

International Nuclear Information System (INIS)

Kabalka, G.W.

1988-06-01

The primary objective of the DOE Nuclear Medicine Program at The University of Tennessee is the creation of new methods for intoducing short-lived isotopes into agents for use in PET and SPECT. A portion of our effort is directed toward the design and in vivo quantitation of boron-containing neutron therapy agents. The uniqueness of the program is its focus on the design of new chemistry (molecular architecture) and technology as opposed to the application of known reactions to the synthesis of specific radiopharmaceuticals. The following topics are outlined in this paper: new isotope incorporation reactions utilizing nitrogen 13, oxygen 15, and carbon 11; technetium-boron complexes; boron-neutron-capture

Use of fast reactors for actinide transmutation

International Nuclear Information System (INIS)

1993-03-01

The management of radioactive waste is one of the key issues in today's discussions on nuclear energy, especially the long term disposal of high level radioactive wastes. The recycling of plutonium in liquid metal fast breeder reactors (LMFBRs) would allow 'burning' of the associated extremely long life transuranic waste, particularly actinides, thus reducing the required isolation time for high level waste from tens of thousands of years to hundreds of years for fission products only. The International Working Group on Fast Reactors (IWGFR) decided to include the topic of actinide transmutation in liquid metal fast breeder reactors in its programme. The IAEA organized the Specialists Meeting on Use of Fast Breeder Reactors for Actinide Transmutation in Obninsk, Russian Federation, from 22 to 24 September 1992. The specialists agree that future progress in solving transmutation problems could be achieved by improvements in: Radiochemical partitioning and extraction of the actinides from the spent fuel (at least 98% for Np and Cm and 99.9% for Pu and Am isotopes); technological research and development on the design, fabrication and irradiation of the minor actinides (MAs) containing fuels; nuclear constants measurement and evaluation (selective cross-sections, fission fragments yields, delayed neutron parameters) especially for MA burners; demonstration of the feasibility of the safe and economic MA burner cores; knowledge of the impact of maximum tolerable amount of rare earths in americium containing fuels. Refs, figs and tabs

Detection of the actinides and cesium from environmental samples

Science.gov (United States)

Snow, Mathew Spencer

Detection of the actinides and cesium in the environment is important for a variety of applications ranging from environmental remediation to safeguards and nuclear forensics. The utilization of multiple different elemental concentrations and isotopic ratios together can significantly improve the ability to attribute contamination to a unique source term and/or generation process; however, the utilization of multiple elemental "signatures" together from environmental samples requires knowledge of the impact of chemical fractionation for various elements under a variety of environmental conditions (including predominantly aqueous versus arid conditions). The research reported in this dissertation focuses on three major areas: 1. Improving the understanding of actinide-mineral interactions at ultra-low concentrations. Chapter 2 reports a batch sorption and modeling study of Np(V) sorption to the mineral goethite from attomolar to micromolar concentrations. 2. Improving the detection capabilities for Thermal Ionization Mass Spectrometry (TIMS) analyses of ultra-trace cesium from environmental samples. Chapter 4 reports a new method which significantly improves the chemical yields, purification, sample processing time, and ultimately, the detection limits for TIMS analyses of femtogram quantities of cesium from a variety of environmental sample matrices. 3. Demonstrating how actinide and cesium concentrations and isotopic ratios from environmental samples can be utilized together to determine a wealth of information including environmental transport mechanisms (e.g. aqueous versus arid transport) and information on the processes which generated the original material. Chapters1, 3 and 5 demonstrate these principles using Pu, Am, Np, and Cs concentrations and isotopic ratios from contaminated soils taken near the Subsurface Disposal Area (SDA) of Idaho National Laboratory (INL) (a low level radioactive waste disposal site in southeastern Idaho).

Amount, disposal and relative toxicity of long-lived fission products and actinides in the radioactive wastes of the nuclear fuel cycles

International Nuclear Information System (INIS)

Haug, H.O.

1975-11-01

A review is presented on the magnitude of the long-term problems of radioactive wastes from the nuclear power industry of the FRG (and Western Europe). The production of long-lived fission products and actinides has been calculated for several fuel types of the uranium-plutonium and thorium-uranium fuel cycles and related to a prediction of the development and share of LWR, FBR and HTGR. The quantities and concentrations of actinides, the radioactivity and relative toxicity index of the wastes of reprocessing (and fuel refabrication) and their changes by radioactive decay are presented. The radiotoxicity of the nuclide inventory of the solidified high-level wastes have been compared with naturally occuring uranium ores. On the long term (>10 3 years) the radiotoxicity level of the total area of the final repository in deep geological formation does not result in a significantly higher radiotoxicity level than an uranium ore deposit of low uranium content. Also discussed have been the chemical separation of the actinides from high-level wastes and recycling in fission reactors. (orig.) [de

Isotope separation process

International Nuclear Information System (INIS)

Wexler, Sol; Young, C.E.

1976-01-01

Description is given of method for separating a specific isotope from a mixture of isotopes of an actinide element present as MF 6 , wherein M is the actinide element. It comprises: preparing a feed gas mixture of MF 6 in a propellant gas; passing the feed gas mixture under pressure through an expansion nozzle while heating the mixture to about 600 0 C; releasing the heated gas mixture from the nozzle into an exhaust chamber having a reduced pressure, whereby a gas jet of MF 6 molecules, MF 6 molecular clusters and propellant gas molecules is formed, the MF 6 molecules having a translational energy of about 3 eV; converting the MF 6 molecules to MF 6 ions by passing the jet through a cross jet of electron donor atoms so that an electron transfer takes place between the MF 6 - molecules and the electron donor atoms whereby the jet is now quasi-neutral, containing negative MF 6 - ions and positive donor ions; passing the quasi-neutral jet through a radiofrequency mass filter tuned to separate the MF 6 ions containing the specific isotope from the MF 6 - ions of the other isotopes and neutralizing and collecting the MF 6 molecules of the specific isotope [fr

Removal of actinides from selected nuclear fuel reprocessing wastes

International Nuclear Information System (INIS)

Navratil, J.D.; Thompson, G.H.

1979-01-01

The US Department of Energy awarded Oak Ridge National Laboratory a program to develop a cost-risk-benefit analysis of partitioning long-lived nuclides from waste and transmuting them to shorter lived or stable nuclides. Two subtasks of this program were investigated at Rocky Flats. In the first subtask, methods for solubilizing actinides in incinerator ash were tested. Two methods appear to be preferable: reaction with ceric ion in nitric acid or carbonate-nitrate fusion. The ceric-nitric acid system solubilizes 95% of the actinides in ash; this can be increased by 2 to 4% by pretreating ash with sodium hydroxide to solubilize silica. The carbonate-nitrate fusion method solubilizes greater than or equal to 98% of the actinides, but requires sodium hydroxide pretreatment. Two additional disadvantages are that it is a high-temperature process, and that it generates a lot of salt waste. The second subtask comprises removing actinides from salt wastes likely to be produced during reactor fuel fabrication and reprocessing. A preliminary feasibility study of solvent extraction methods has been completed. The use of a two-step solvent extraction system - tributyl phosphate (TBP) followed by extraction with a bidentate organophosphorous extractant (DHDECMP) - appears to be the most efficient for removing actinides from salt waste. The TBP step would remove most of the plutonium and > 99.99% of the uranium. The second step using DHDECMP would remove > 99.91% of the americium and the remaining plutonium (> 99.98%) and other actinides from the acidified salt waste. 8 figures, 11 tables

Short-lived radioactive nuclides in meteorites and early solar system processes

International Nuclear Information System (INIS)

Chaussidon, M.; Gounelle, M.

2007-01-01

Now extinct, short-lived radioactive nuclides, such as 7 Be (T 1/2 = 53 days), 10 Be (T 1/2 = 1.5 Ma), 26 Al (T 1/2 = 0.74 Ma), 36 Cl (T 1/2 = 0.3 Ma), 41 Ca (T 1/2 = 0.1 Ma), 53 Mn (T 1/2 = 3.7 Ma) and 60 Fe (T 1/2 = 1.5 Ma), were present in the proto-solar nebula when the various components of meteorites formed. The presence of these radioactive isotopes requires a 'last-minute' origin, either nucleosynthesis in a massive star dying close in space and time to the nascent solar system or production by local irradiation of part of the proto-solar disk by high-energy solar cosmic rays. In this review, we list: (i) the different observations indicating the existence of multiple origins for short-lived radioactive nuclides, namely 7 Be, 10 Be and 36 Cl for irradiation scenario and 60 Fe for injection scenario; (ii) the constraints that exist on their distribution (homogeneous or heterogeneous) in the accretion disk; (iii) the constraints they brought on the timescales of nebular processes (from Ca-Al-rich inclusions to chondrules) and of the accretion and differentiation of planetesimals. (authors)

Development of ion beam sputtering techniques for actinide target preparation

International Nuclear Information System (INIS)

Aaron, W.S.; Zevenbergen, L.A.; Adair, H.L.

1985-01-01

Ion beam sputtering is a routine method for the preparation of thin films used as targets because it allows the use of minimum quantity of starting material, and losses are much lower than most other vacuum deposition techniques. Work is underway in the Isotope Research Materials Laboratory (IRML) at ORNL to develop the techniques that will make the preparation of actinide targets up to 100 μg/cm 2 by ion beam sputtering a routinely available service from IRML. The preparation of the actinide material in a form suitable for sputtering is a key to this technique, as is designing a sputtering system that allows the flexibility required for custom-ordered target production. At present, development work is being conducted on low-activity in a bench-top system. The system will then be installed in a hood or glove box approved for radioactive materials handling where processing of radium, actinium, and plutonium isotopes among others will be performed. (orig.)

Overall assessment of actinide partitioning and transmutation for waste management purposes

International Nuclear Information System (INIS)

Blomeke, J.O.; Croff, A.G.; Finney, B.C.; Tedder, D.W.

1980-01-01

A program to establish the technical feasibility and incentives for partitioning (i.e., recovering) actinides from fuel cycle wastes and then transmuting them in power reactors to shorter-lived or stable nuclides has recently been concluded at the Oak Ridge National Laboratory. The feasibility was established by experimentally investigating the reduction that can be practicably achieved in the actinide content of the wastes sent to a geologic repository, and the incentives for implementing this concept were defined by determining the incremental costs, risks, and benefits. Eight US Department of Energy laboratories and three private companies participated in the program over its 3-year duration. A reference fuel cycle was chosen based on a self-generated plutonium recycle PWR, and chemical flowsheets based on solvent extraction and ion-exchange techniques were generated that have the potential to reduce actinides in fuel fabrication and reprocessing plant wastes to less than 0.25% of those in the spent fuel. Waste treatment facilities utilizing these flowsheets were designed conceptually, and their costs were estimated. Finally, the short-term (contemporary) risks from fuel cycle operations and long-term (future) risks from deep geologic disposal of the wastes were estimated for cases with and without partitioning and transmutation. It was concluded that, while both actinide partitioning from wastes and transmutation in power reactors appear to be feasible using currently identified and studied technology, implementation of this concept cannot be justified because of the small long-term benefits and substantially increased costs of the concept

Continuous administration of short-lived radioisotope tracers and the analogous Laplace transform

International Nuclear Information System (INIS)

Orr, J.S.

1979-01-01

Short-lived radioactive tracers are used because of the low radiation dose to patients. Another advantage finding increasing use, however, is that the equilibrium activities achieved by continuous administration to a steady state contain kinetic information. This is not the case with long-lived isotopes. The derivation of quantitative kinetic information in the form of rate constants or flows requires the formulation of a model of the system being studied. Several approaches to this have been published based on a model of single compartments with simultaneous arrival of tracer. To deal with more realistic models a method is proposed which uses the analogy between the procedure of continuous administration of short-lived tracer and the Laplace transform. This analogy permits all the theorems of Laplace transform theory to be applied to the analysis of measured activities. The basis of the analogy is explained and examples are given of its application to a number of models which represent actual physiology more realistically than single compartment models. In these applications the transformed equations representing the model, with measured values of activity inserted for each transform, are solved to derive the rate constants. This is different from the use of Laplace transforms where the constant coefficients are known and the initial value problem is solved to find the behaviour of the variables. (author)

ACTINET - EU network of excellence for actinide sciences

International Nuclear Information System (INIS)

Gompper, K.

2006-01-01

ACTINET, the Network of Excellence for Actinide Sciences within the 6th EU Framework Program, was launched in March 2004 for an initial period of four years. A number of tools are available in ACTINET to serve the purposes of the project, i.e. stimulate and coordinate actinide research in Europe, promote integration, train young scientists and, in this way, ensure and enhance European competence. The large European actinide laboratories with their unique experimental and analytical equipment are available to scientists from Europe as so-called 'pool facilities' within the framework of joint research projects. Setting up a 'theoretical user lab' has turned out to be a promising way of exploiting the synergies of theory and experiment in various fields of actinide science. Joint research projects are supported within the network, working with actinides being made possible in the pool facilities. Training and instruction are ensured by seminars, workshops, and schools organized annually. In familiarizing young scientists with actinide work, ACTINET exercises training functions and contributes to ensuring and enhancing European competence in the field on the medium and long term. Even after only half of its term, ACTINET is developing into a live network, thus decisively contributing towards promoting, coordinating and integrating European actinide research. As actinides play a key role in the use of nuclear power, this benefits European industries, research centers, operators of nuclear power plants and nuclear facilities as well as licensing and regulatory authorities. (orig.)

Behaviour of the homologues of Rf and Db in complexing media

International Nuclear Information System (INIS)

Trubert, D.; Monroy Guzman, F.; Hussonnois, M.; Brillard, L.; Le Naour, C.; Servajean, V.; Constantinescu, O.; Constantinescu, M.; Ardisson, G.; Barci, V.; Weiss, B.

1999-01-01

In order to study the chemical behaviour of the trans-actinide elements, the chemical properties of their most probable homologues have been investigated by ion exchange methods in various complexing media. A new chromatographic method allowing the determination of distribution coefficients in the case o short-lived isotopes has been developed and successfully tested with the RACHEL device. (authors)

Preparation of higher-actinide burnup and cross section samples

International Nuclear Information System (INIS)

Adair, H.L.; Kobisk, E.H.; Quinby, T.C.; Thomas, D.K.; Dailey, J.M.

1981-01-01

A joint research program involving the United States and the United Kingdom was instigated about four years ago for the purpose of studying burnup of higher actinides using in-core irradiation in the fast reactor at Dounreay, Scotland. Simultaneously, determination of cross sections of a wide variety of higher actinide isotopes was proposed. Coincidental neutron flux and energy spectral measurements were to be made using vanadium encapsulated dosimetry materials in the immediate region of the burnup and cross section samples. The higher actinide samples chosen for the burnup study were 241 Am and 244 Cm in the forms of Am 2 O 3 , Cm 2 O 3 , and Am 6 Cm(RE) 7 O 21 , where (RE) represents a mixture of lanthanide sesquioxides. It is the purpose of this paper to describe technology development and its application in the preparation of the fuel specimens and the cross section specimens that are being used in this cooperative program

Alpha decay and cluster decay of some neutron-rich actinide nuclei

Indian Academy of Sciences (India)

2017-02-09

Feb 9, 2017 ... Abstract. Nuclei in the actinide region are good in exhibiting cluster radioactivity. In the present work, the half-lives of α-decay and heavy cluster emission from certain actinide nuclei have been calculated using cubic plus Yukawa plus exponential model (CYEM). Our model has a cubic potential for the ...

Nuclear Data for Reactor Physics: Cross sections and level densities in the actinide region

Directory of Open Access Journals (Sweden)

Bernstein L.

2010-03-01

Full Text Available Nuclear data in the actinide region are particularly important because they are basis behind all simulations of nuclear reactor core behaviour over both long time scales (fuel depletion and waste production and short time scales (accident scenarios. Nuclear reaction cross sections must be known as precisely as possible so that core reaction rates can be accurately calculated. Although cross section measurements in this region have been widely performed, for certain nuclei, particularly those with short half lives, direct measurements are either very difficult or impossible and thus reactor simulations must rely on theoretical calculations or extrapolations from neighbouring nuclei. The greatest uncertainty in theoretical cross section calculations comes from the lack of knowledge of level densities, for which predicted values can often be incorrect by a factor of two or more. Therefore there is a strong case for a systematic experimental study of level densities in the actinide region for the purpose of a providing a stringent test of theoretical cross section calculations for nuclei where experimental cross section data are available and b for providing better estimations of cross sections for nuclei in which no cross section data are available.

Actinide burning and waste disposal

Energy Technology Data Exchange (ETDEWEB)

Pigford, T H [University of California, Berkeley, CA (United States)

1990-07-01

for the second repository would be emplaced in the first repository. Reprocessing would now include separation of the fission products strontium and cesium. After interim storage for 20-300 years, the remaining cesium would also be emplaced in the first repository. One DOE laboratory proposes an accelerator to destroy actinides and long-lived fission products. The time required for geologic or managed storage is said to be reduced to only one to several centuries.

Actinide burning and waste disposal

International Nuclear Information System (INIS)

Pigford, T.H.

1990-01-01

for the second repository would be emplaced in the first repository. Reprocessing would now include separation of the fission products strontium and cesium. After interim storage for 20-300 years, the remaining cesium would also be emplaced in the first repository. One DOE laboratory proposes an accelerator to destroy actinides and long-lived fission products. The time required for geologic or managed storage is said to be reduced to only one to several centuries

Breeding and plutonium characterization analysis on actinides closed water-cooled thorium reactor

International Nuclear Information System (INIS)

Permana, Sidik; Sekimoto, Hiroshi; Takaki, Naoyuki

2009-01-01

Higher difficulties (barrier) or more complex design of nuclear weapon, material fabrication and handling and isotopic enrichment can be achieved by a higher isotopic barrier. The isotopic material barrier includes critical mass, heat-generation rate, spontaneous neutron generation and radiation. Those isotopic barriers in case of plutonium isotope is strongly depend on the even mass number of plutonium isotope such as 238 Pu, 240 Pu and 242 Pu and for 233 U of thorium cycle depends on 232 U. In this present study, fuel sustainability as fuel breeding capability and plutonium characterization as main focus of proliferation resistance analysis have been analyzed. Minor actinide (MA) is used as doping material to be loaded into the reactors with thorium fuel. Basic design parameters are based on actinide closed-cycle reactor cooled by heavy water. The evaluation use equilibrium burnup analysis coupled with cell calculation of SRAC and nuclear data library is JENDL.32. Parametrical survey has been done to analyze the effect of MA doping rate, different moderation ratio for several equilibrium burnup cases. Plutonium characterization which based on plutonium isotope composition is strongly depending on MA doping concentration and different moderation conditions. Breeding condition can be achieved and high proliferation resistance level can be obtained by the present reactor systems. Higher isotopic plutonium composition of Pu-238 (more than 40%) can be obtained compared with other plutonium isotopes. In addition, higher moderation ratio gives the isotope composition of 238 Pu increases, however, it obtains lower composition when MA doping is increased and it slightly lower composition for higher burnup. Meanwhile, higher 240 Pu composition can be achieved by higher MA doping rate as well as for obtaining higher breeding capability. (author)

Citrate based ''TALSPEAK'' lanthanide-actinide separation process

International Nuclear Information System (INIS)

Del Cul, G.D.; Bond, W.D.; Toth, L.M.; Davis, G.D.; Dai, S.; Metcalf, D.H.

1994-09-01

The potential hazard posed to future generations by long-lived radionuclides such as the transuranic elements (TRU) is perceived as a major problem associated with the use of nuclear power. TRU wastes have to remain isolated from the environment for ''geological'' periods of time. The costs of building, maintaining, and operating a ''geological TRU repository'' can be very high. Therefore, there are significant economical advantages in segregating the relatively low volume of TRU wastes from other nuclear wastes. The chemical behavior of lanthanides and actinides, 4f and 5f elements respectively, is rather similar. As a consequence, the separation of these two groups is difficult. The ''TALSPEAK'' process (Trivalent Actinide Lanthanide Separations by Phosphorus-reagent Extraction from Aqueous Complexes) is one of the few means available to separate the trivalent actinides from the lanthanides. The method is based on the preferential complexation of the trivalent actinides by an aminopolyacetic acid. Cold experiments showed that by using citric acid the deleterious effects produced by impurities such as zirconium are greatly reduced

An optimization methodology for heterogeneous minor actinides transmutation

Science.gov (United States)

Kooyman, Timothée; Buiron, Laurent; Rimpault, Gérald

2018-04-01

In the case of a closed fuel cycle, minor actinides transmutation can lead to a strong reduction in spent fuel radiotoxicity and decay heat. In the heterogeneous approach, minor actinides are loaded in dedicated targets located at the core periphery so that long-lived minor actinides undergo fission and are turned in shorter-lived fission products. However, such targets require a specific design process due to high helium production in the fuel, high flux gradient at the core periphery and low power production. Additionally, the targets are generally manufactured with a high content in minor actinides in order to compensate for the low flux level at the core periphery. This leads to negative impacts on the fuel cycle in terms of neutron source and decay heat of the irradiated targets, which penalize their handling and reprocessing. In this paper, a simplified methodology for the design of targets is coupled with a method for the optimization of transmutation which takes into account both transmutation performances and fuel cycle impacts. The uncertainties and performances of this methodology are evaluated and shown to be sufficient to carry out scoping studies. An illustration is then made by considering the use of moderating material in the targets, which has a positive impact on the minor actinides consumption but a negative impact both on fuel cycle constraints (higher decay heat and neutron) and on assembly design (higher helium production and lower fuel volume fraction). It is shown that the use of moderating material is an optimal solution of the transmutation problem with regards to consumption and fuel cycle impacts, even when taking geometrical design considerations into account.

Colloidal products and actinide species in leachate from spent nuclear fuel

International Nuclear Information System (INIS)

Finn, P.A.; Buck, E.C.; Gong, M.; Hoh, J.C.; Emery, J.W.; Hafenrichter, L.D.; Bates, J.K.

1993-01-01

Two well-characterized types of spent nuclear fuel (ATM-103 and ATM-106) were subjected to unsaturated leach tests with simulated groundwater at 90 degrees C. The actinides present in the leachate were determined at the end of two successive periods of ∼60 days and after an acid strip done at the end of the second period. Both colloidal and soluble actinide species were detected in the leachates which had pHs ranging from 4 to 7. The uranium phases identified in the colloids were schoepite and soddyite. In addition, the actinide release behavior of the two fuels appeared to be different for both the total amount of material released and the relative amount of each isotope released. This paper will focus on the detection and identification of the colloidal species observed in the leachate that was collected after each of the first two successive testing periods of approximately 60 days each. In addition, preliminary values for the total actinide release for these two periods are reported

What fits best minor actinides as a die material?

International Nuclear Information System (INIS)

Hinfray, J.

2003-01-01

Zirconolite might be the die material used to confine actinides definitively. Cea's teams have been investigating the ability of zirconolite to trap actinide atoms in its own crystal structure. These studies have been performed with 239 Pu that presents the same ability to set chemical links with the constituents of the die as 3 minor actinides do. Crystal materials like zirconolite are more sensitive to self irradiation than glass. The next step of the characterization of zirconolite is to evaluate its capacity to sustain self alpha irradiation. In order to do so, 238 Pu is used since its relatively short period (T = 87 years) allows an acceleration of the process : damages cumulated in the die material in 2 years will be equivalent to those produced by minor actinides for millions years. The results will be known in 2004. (A.C.)

Dynamics of radioactive lead isotopes in the global environmental atmosphere

International Nuclear Information System (INIS)

Koike, Yuya; Kosako, Toshiso

2006-01-01

Fundamental information of radioactive lead isotopes, which used as the atmospheric tracer in the global environmental atmosphere, is reviewed. Emanation and exhalation of Rn and Tn, parent nuclide, is stated. Some reports on measurement and application of short-lived lead isotopes are reported. Transfer of radioactive lead isotopes in the atmosphere, vertical profiles of radon, thoron, and short-lived lead isotopes for different turbulent mixing conditions, deposition to aerosol, basic processes of Rn decay product behavior in air defining 'unattached' and 'aerosol-attached' activities, seasonal variation of atmospheric 210 Pb concentration at Beijing and Chengdu, seasonal variation of atmospheric 212 Pb concentration at several observation sites in Japan Islands, and variation in the atmospheric concentration of 212 Pb along with SO 2 are shown. (S.Y.)

Radiopharmaceuticals and other compounds labelled with short-lived radionuclides

CERN Document Server

Welch, Michael J

2013-01-01

Radiopharmaceuticals and Other Compounds Labelled with Short-Lived Radionuclides covers through both review and contributed articles the potential applications and developments in labeling with short-lived radionuclides whose use is restricted to institutions with accelerators. The book discusses the current and potential use of generator-produced radionuclides as well as other short-lived radionuclides, and the problems of quality control of such labeled compounds. The book is useful to nuclear medicine physicians.

Reanalysis of gastrointestinal absorption factors for plutonium and other actinide elements

International Nuclear Information System (INIS)

Bhattacharyya, M.H.; Larsen, R.P.; Toohey, R.E.; Moretti, E.S.; Oldham, R.D.; Spaletto, M.I.; Engel, M.C.

1981-01-01

This project studies the gastrointestinal absorption of plutonium and other actinide elements relevant to nuclear power production, at concentrations at or below their respective maximum permissible concentrations (MPC's) in drinking water, using high specific activity isotopes. The gastrointestinal absorption of plutonium is measured in mice, rats, and dogs exposed to plutonium either via drinking water or by gavage. Plutonium concentrations are determined in liver and eviscerated carcass at 6 days (mice and rats) or 4 weeks (dogs). Administered solutions are 1 x 10 -10 M in Pu (the molar concentration at MPC for 239 Pu) and contain one of several high specific activity isotopes ( 237 Pu, 47-day half-life; 236 Pu, 2.8-year half-life; 238 Pu, 86-year half-life). Fasted mice and rats, administered plutonium solutions that are: (1) low in concentration (10- 10 M); and (2) carefully prepared to assure a given oxidation state and to avoid hydrolysis and polymes, and major policy issues. The first HEED for near-term battery energy storage systems (lead/acid, nickel/zinc, and nickel/iron) astention being paid to potential releases of radionuclides at relatively short times after disposal

Gas core reactors for actinide transmutation and breeder applications. Annual report

International Nuclear Information System (INIS)

Clement, J.D.; Rust, J.H.

1978-01-01

This work consists of design power plant studies for four types of reactor systems: uranium plasma core breeder, uranium plasma core actinide transmuter, UF6 breeder and UF6 actinide transmuter. The plasma core systems can be coupled to MHD generators to obtain high efficiency electrical power generation. A 1074 MWt UF6 breeder reactor was designed with a breeding ratio of 1.002 to guard against diversion of fuel. Using molten salt technology and a superheated steam cycle, an efficiency of 39.2% was obtained for the plant and the U233 inventory in the core and heat exchangers was limited to 105 Kg. It was found that the UF6 reactor can produce high fluxes (10 to the 14th power n/sq cm-sec) necessary for efficient burnup of actinide. However, the buildup of fissile isotopes posed severe heat transfer problems. Therefore, the flux in the actinide region must be decreased with time. Consequently, only beginning-of-life conditions were considered for the power plant design. A 577 MWt UF6 actinide transmutation reactor power plant was designed to operate with 39.3% efficiency and 102 Kg of U233 in the core and heat exchanger for beginning-of-life conditions

Actinides in irradiated graphite of RBMK-1500 reactor

Energy Technology Data Exchange (ETDEWEB)

Plukienė, R., E-mail: rita@ar.fi.lt; Plukis, A.; Barkauskas, V.; Gudelis, A.; Gvozdaitė, R.; Duškesas, G.; Remeikis, V.

2014-10-01

Highlights: • Activation of actinides in the graphite of the RBMK-1500 reactor was analyzed. • Numerical modeling using SCALE 6.1 and MCNPX was used for actinide calculation. • Measurements of the irradiated graphite sample were used for model validation. • Results are important for further decommissioning process of the RBMK type reactors. - Abstract: The activation of graphite in the nuclear power plants is the problem of high importance related with later graphite reprocessing or disposal. The activation of actinide impurities in graphite due to their toxicity determines a particular long term risk to waste management. In this work the activation of actinides in the graphite constructions of the RBMK-1500 reactor is determined by nuclear spectrometry measurements of the irradiated graphite sample from the Ignalina NPP Unit I and by means of numerical modeling using two independent codes SCALE 6.1 (using TRITON-VI sequence) and MCNPX (v2.7 with CINDER). Both models take into account the 3D RBMK-1500 reactor core fragment with explicit graphite construction including a stack and a sleeve but with a different simplification level concerning surrounding graphite and construction of control roads. The verification of the model has been performed by comparing calculated and measured isotope ratios of actinides. Also good prediction capabilities of the actinide activation in the irradiated graphite have been found for both calculation approaches. The initial U impurity concentration in the graphite model has been adjusted taking into account the experimental results. The specific activities of actinides in the irradiated RBMK-1500 graphite constructions have been obtained and differences between numerical simulation results, different structural parts (sleeve and stack) as well as comparison with previous results (Ancius et al., 2005) have been discussed. The obtained results are important for further decommissioning process of the Ignalina NPP and other RBMK

Actinide metal processing

International Nuclear Information System (INIS)

Sauer, N.N.; Watkin, J.G.

1992-01-01

A process for converting an actinide metal such as thorium, uranium, or plutonium to an actinide oxide material by admixing the actinide metal in an aqueous medium with a hypochlorite as an oxidizing agent for sufficient time to form the actinide oxide material and recovering the actinide oxide material is described together with a low temperature process for preparing an actinide oxide nitrate such as uranyl nitrate. Additionally, a composition of matter comprising the reaction product of uranium metal and sodium hypochlorite is provided, the reaction product being an essentially insoluble uranium oxide material suitable for disposal or long term storage

A comparison of radioactive waste from first generation fusion reactors and fast fission reactors with actinide recycling

International Nuclear Information System (INIS)

Koch, M.; Kazimi, M.S.

1991-04-01

Limitations of the fission fuel resources will presumably mandate the replacement of thermal fission reactors by fast fission reactors that operate on a self-sufficient closed fuel cycle. This replacement might take place within the next one hundred years, so the direct competitors of fusion reactors will be fission reactors of the latter rather than the former type. Also, fast fission reactors, in contrast to thermal fission reactors, have the potential for transmuting long-lived actinides into short-lived fission products. The associated reduction of the long-term activation of radioactive waste due to actinides makes the comparison of radioactive waste from fast fission reactors to that from fusion reactors more rewarding than the comparison of radioactive waste from thermal fission reactors to that from fusion reactors. Radioactive waste from an experimental and a commercial fast fission reactor and an experimental and a commercial fusion reactor has been characterized. The fast fission reactors chosen for this study were the Experimental Breeder Reactor 2 and the Integral Fast Reactor. The fusion reactors chosen for this study were the International Thermonuclear Experimental Reactor and a Reduced Activation Ferrite Helium Tokamak. The comparison of radioactive waste parameters shows that radioactive waste from the experimental fast fission reactor may be less hazardous than that from the experimental fusion reactor. Inclusion of the actinides would reverse this conclusion only in the long-term. Radioactive waste from the commercial fusion reactor may always be less hazardous than that from the commercial fast fission reactor, irrespective of the inclusion or exclusion of the actinides. The fusion waste would even be far less hazardous, if advanced structural materials, like silicon carbide or vanadium alloy, were employed

A comparison of radioactive waste from first generation fusion reactors and fast fission reactors with actinide recycling

Energy Technology Data Exchange (ETDEWEB)

Koch, M.; Kazimi, M.S.

1991-04-01

Limitations of the fission fuel resources will presumably mandate the replacement of thermal fission reactors by fast fission reactors that operate on a self-sufficient closed fuel cycle. This replacement might take place within the next one hundred years, so the direct competitors of fusion reactors will be fission reactors of the latter rather than the former type. Also, fast fission reactors, in contrast to thermal fission reactors, have the potential for transmuting long-lived actinides into short-lived fission products. The associated reduction of the long-term activation of radioactive waste due to actinides makes the comparison of radioactive waste from fast fission reactors to that from fusion reactors more rewarding than the comparison of radioactive waste from thermal fission reactors to that from fusion reactors. Radioactive waste from an experimental and a commercial fast fission reactor and an experimental and a commercial fusion reactor has been characterized. The fast fission reactors chosen for this study were the Experimental Breeder Reactor 2 and the Integral Fast Reactor. The fusion reactors chosen for this study were the International Thermonuclear Experimental Reactor and a Reduced Activation Ferrite Helium Tokamak. The comparison of radioactive waste parameters shows that radioactive waste from the experimental fast fission reactor may be less hazardous than that from the experimental fusion reactor. Inclusion of the actinides would reverse this conclusion only in the long-term. Radioactive waste from the commercial fusion reactor may always be less hazardous than that from the commercial fast fission reactor, irrespective of the inclusion or exclusion of the actinides. The fusion waste would even be far less hazardous, if advanced structural materials, like silicon carbide or vanadium alloy, were employed.

Status of nuclear data for actinides

Energy Technology Data Exchange (ETDEWEB)

Guzhovskii, B.Y.; Gorelov, V.P.; Grebennikov, A.N. [Russia Federal Nuclear Centre, Arzamas (Russian Federation)] [and others

1995-10-01

Nuclear data required for transmutation problem include many actinide nuclei. In present paper the analysis of neutron fission, capture, (n,2n) and (n,3n) reaction cross sections at energy region from thermal point to 14 MeV was carried out for Th, Pa, U, Np, Pu, Am and Cm isotops using modern evaluated nuclear data libraries and handbooks of recommended nuclear data. Comparison of these data indicates on substantial discrepancies in different versions of files, that connect with quality and completeness of original experimental data.

Half-lives of long-lived isotopes of transactinium elements from 228Th to 257Fm

International Nuclear Information System (INIS)

Surin, V.M.; Fomushkin, Eh.F.

1983-09-01

The experimental measurements and critical evaluation results of the long-lived isotope half-decay periods of transactinium elements (from 228 Th to 257 Fm) are given on July 1981 to be published in open literature and related to the natural radioactive decay. From the massif of the known half-decay periods the most reliable data were selected, received or evaluated and recommended for practical use; the calculations of isotope specific activities were performed on this data. (author)

Actinide-handling experience for training and education of future expert under J-ACTINET

International Nuclear Information System (INIS)

Osaka, Masahiko; Sato, Isamu; Miwa, Shuhei; Konashi, Kenji; Li, Dexin; Homma, Yoshiya; Yamamura, Tomoo; Hayashi, Hirokazu; Minato, Kazuo; Sekimoto, Syun; Kubota, Takumi; Fukutani, Satoshi; Hori, Junichi; Okumura, Ryo; Uehara, Akihiro; Fujii, Toshiyuki; Yamana, Hajimu; Kurosaki, Ken; Muta, Hiroaki; Ohishi, Yuji; Yamanaka, Shinsuke; Uno, Masayoshi; Yaita, Tsuyoshi

2011-01-01

Summer schools for future experts have successfully been completed under Japan Actinide Network (J-ACTINET) for the purpose of development of human resources who are expected to be engaged in every areas of actinide-research/engineering. The first summer school was held in Ibaraki-area in August 2009, followed by the second one in Kansai-area in August 2010. Two summer schools have focused on actual experiences of actinides in actinide-research fields for university students and young researchers/engineers as an introductory course of actinide-researches. Many efforts were made to awaken interests into actinide-researches inside the participants during short periods of schools, 3 to 4 days. As actinides must be handled inside special apparatuses such as an air-tight globe-box with well-trained and qualified technicians, programs were optimized for effective experiences of actinides-handling. Several quasi actinide-handling experiences at the actinide-research fields have attracted attentions of participants at the first school in Ibaraki-area. The actual experiments using actinides-containing solutions have been carried out at the second school in Kansai-area. Future summer schools will be held every year for the sustainable human resource development in various actinide-research fields, together with other training and education programs conducted by the J-ACTINET. (author)

Review of the treatment of actinides-bearing radioactive wastes

International Nuclear Information System (INIS)

Krause, H.

1983-01-01

Actinides bearing wastes are produced above all in the course of irradiated nuclear fuel reprocessing and during fabrication of mixed oxide fuel elements. Particular attention in research and development work must be paid to this type of waste, mainly on account of its longevity. In practical application, the specific character of the actinides bearing wastes has been largely recognized. Nevertheless, definitions and methods of treatment generally accepted worldwide are still missing today. This has no bearing as yet on present day treatment of radioactive wastes. But by the time of application of the breeder technology at the latest a special treatment concept should be available which complies with the high actinide contents and short precooling periods of the wastes

The application of scanning electron microscopy to the determination of elemental and isotopic composition in individual actinide particles

International Nuclear Information System (INIS)

Vatter, I.; Cattle, G.; Tushingham, J.

2000-01-01

Techniques for the determination of both elemental and isotopic composition of actinides within single particles are required by the IAEA in support of their environmental safeguards programme. SEM and SIMS are valuable techniques for the measurement of elemental and isotopic composition, respectively, on the particle scale. The potential for effective combination of SEM and SIMS has been investigated at Harwell Laboratory. In trials, copper finder grids have been successfully used to enable re-identification of particles between SEM and SIMS instruments. Use of the grids enables rapid relocation of particles pre-selected by SEM for SIMS measurement. The work has highlighted a possible matrix effect in plutonium measurement that results in variable sensitivity dependent on the presence of other elements (including uranium). This effect would limit the use of SIMS to obtain elemental ratios, and highlights the requirement to use both SEM and SIMS to gain full and accurate information. The possible use of autoradiography as an adjunct to SEM has been investigated. In principle, autoradiography could be used to identify higher enrichments of uranium and enable pre-selection of particles for SIMS measurement. During trials, practical problems have been encountered which have demonstrated this particular approach to be unsuitable. (author)

Conservative axial burnup distributions for actinide-only burnup credit

International Nuclear Information System (INIS)

Kang, C.; Lancaster, D.

1997-11-01

Unlike the fresh fuel approach, which assumes the initial isotopic compositions for criticality analyses, any burnup credit methodology must address the proper treatment of axial burnup distributions. A straightforward way of treating a given axial burnup distribution is to segment the fuel assembly into multiple meshes and to model each burnup mesh with the corresponding isotopic compositions. Although this approach represents a significant increase in modeling efforts compared to the uniform average burnup approach, it can adequately determine the reactivity effect of the axial burnup distribution. A major consideration is what axial burnup distributions are appropriate for use in light of many possible distributions depending on core operating conditions and histories. This paper summarizes criticality analyses performed to determine conservative axial burnup distributions. The conservative axial burnup distributions presented in this paper are included in the Topical Report on Actinide-Only Burnup Credit for Pressurized Water Reactor Spent Nuclear Fuel Packages, Revision 1 submitted in May 1997 by the US Department of Energy (DOE) to the US Nuclear Regulatory Commission (NRC). When approved by NRC, the conservative axial burnup distributions may be used to model PWR spent nuclear fuel for the purpose of gaining actinide only burnup credit

Synthesis of tetravalent actinide chlorides. Versatile compounds for actinide chemistry

Energy Technology Data Exchange (ETDEWEB)

Maerz, Juliane [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Div. Chemistry of the F-Elements

2016-07-01

Anhydrous actinide tetrachlorides (AnCl{sub 4}) were synthesized under mild conditions to provide versatile compounds for actinide chemistry. They enable a direct access to actinide complexes with organic and inorganic ligands.

Studies on the properties of hard-spectrum, actinide fissioning reactors. Final report

International Nuclear Information System (INIS)

Nelson, J.B.; Prichard, A.W.; Schofield, P.E.; Robinson, A.H.; Spinrad, B.I.

1980-01-01

It is technically feasible to construct an operable (e.g., safe and stable) reactor to burn waste actinides rapidly. The heart of the concept is a driver core of EBR-II type, with a central radial target zone in which fuel elements, made entirely of waste actinides are exposed. This target fuel undergoes fission, as a result of which actinides are rapidly destroyed. Although the same result could be achieved in more conventionally designed LWR or LMFBR systems, the fast spectrum reactor does a much more efficient job, by virtue of the fact that in both LWR and LMFBR reactors, actinide fission is preceded by several captures before a fissile nuclide is formed. In the fast spectrum reactor that is called ABR (actinide burning reactor), these neutron captures are short-circuited

Accurate determination of Curium and Californium isotopic ratios by inductively coupled plasma quadrupole mass spectrometry (ICP-QMS) in 248Cm samples for transmutation studies

Energy Technology Data Exchange (ETDEWEB)

Gourgiotis, A.; Isnard, H.; Aubert, M.; Dupont, E.; AlMahamid, I.; Cassette, P.; Panebianco, S.; Letourneau, A.; Chartier, F.; Tian, G.; Rao, L.; Lukens, W.

2011-02-01

The French Atomic Energy Commission has carried out several experiments including the mini-INCA (INcineration of Actinides) project for the study of minor-actinide transmutation processes in high intensity thermal neutron fluxes, in view of proposing solutions to reduce the radiotoxicity of long-lived nuclear wastes. In this context, a Cm sample enriched in {sup 248}Cm ({approx}97 %) was irradiated in thermal neutron flux at the High Flux Reactor (HFR) of the Laue-Langevin Institute (ILL). This work describes a quadrupole ICP-MS (ICP-QMS) analytical procedure for precise and accurate isotopic composition determination of Cm before sample irradiation and of Cm and Cf after sample irradiation. The factors that affect the accuracy and reproducibility of isotopic ratio measurements by ICP-QMS, such as peak centre correction, detector dead time, mass bias, abundance sensitivity and hydrides formation, instrumental background, and memory blank were carefully evaluated and corrected. Uncertainties of the isotopic ratios, taking into account internal precision of isotope ratio measurements, peak tailing, and hydrides formations ranged from 0.3% to 1.3%. This uncertainties range is quite acceptable for the nuclear data to be used in transmutation studies.

Actinide recycling in reactors

International Nuclear Information System (INIS)

Kuesters, H.; Wiese, H.W.; Krieg, B.

1995-01-01

The objective is an assessment of the transmutation of long-lived actinides and fission products and the incineration of plutonium for reducing the risk potential of radioactive waste from reactors in comparison to direct waste disposal. The contribution gives an interim account on homogeneous and heterogeneous recycling of 'risk nuclides' in thermal and fast reactors. Important results: - A homogeneous 5 percent admixture of minor actinides (MA) from N4-PWRs to EFR fuel would allow a transmutation not only of the EFR MA, but in addition of the MA from 5 or 6 PWRs of equal power. However, the incineration is restricted by safety considerations. - LWR have only a very low MA incineration potential, due to their disadvantageous neutron capture/fission ratio. - In order to keep the Cm inventory at a low level, it is advantageous to concentrate the Am heterogeneously in particular fuel elements or rods. (orig./HP)

FY2011 Annual Report for the Actinide Isomer Detection Project

International Nuclear Information System (INIS)

Warren, Glen A.; Francy, Christopher J.; Ressler, Jennifer J.; Erikson, Luke E.; Tatishvili, Gocha; Hatarik, R.

2011-01-01

This project seeks to identify a new signature for actinide element detection in active interrogation. This technique works by exciting and identifying long-lived nuclear excited states (isomers) in the actinide isotopes and/or primary fission products. Observation of isomers in the fission products will provide a signature for fissile material. For the actinide isomers, the decay time and energy of the isomeric state is unique to a particular isotope, providing an unambiguous signature for SNM. This project entails isomer identification and characterization and neutron population studies. This document summarizes activities from its third year - completion of the isomer identification characterization experiments and initialization of the neutron population experiments. The population and decay of the isomeric state in 235U remain elusive, although a number of candidate gamma rays have been identified. In the course of the experiments, a number of fission fragment isomers were populated and measured (Ressler 2010). The decays from these isomers may also provide a suitable signature for the presence of fissile material. Several measurements were conducted throughout this project. This report focuses on the results of an experiment conducted collaboratively by PNNL, LLNL and LBNL in December 2010 at LBNL. The measurement involved measuring the gamma-rays emitted from an HEU target when bombarded with 11 MeV neutrons. This report discussed the analysis and resulting conclusions from those measurements. There was one strong candidate, at 1204 keV, of an isomeric signature of 235U. The half-life of the state is estimated to be 9.3 μs. The measured time dependence fits the decay time structure very well. Other possible explanations for the 1204-keV state were investigated, but they could not explain the gamma ray. Unfortunately, the relatively limited statistics of the measurement limit, and the lack of understanding of some of the systematic of the experiment, limit

Analysis and application of heavy isotopes in the environment

Science.gov (United States)

Steier, Peter; Dellinger, Franz; Forstner, Oliver; Golser, Robin; Knie, Klaus; Kutschera, Walter; Priller, Alfred; Quinto, Francesca; Srncik, Michaela; Terrasi, Filippo; Vockenhuber, Christof; Wallner, Anton; Wallner, Gabriele; Wild, Eva Maria

2010-04-01

A growing number of AMS laboratories are pursuing applications of actinides. We discuss the basic requirements of the AMS technique of heavy (i.e., above ˜150 amu) isotopes, present the setup at the Vienna Environmental Research Accelerator (VERA) which is especially well suited for the isotope 236U, and give a comparison with other AMS facilities. Special emphasis will be put on elaborating the effective detection limits for environmental samples with respect to other mass spectrometric methods. At VERA, we have carried out measurements for radiation protection and environmental monitoring ( 236U, 239,240,241,242,244Pu), astrophysics ( 182Hf, 236U, 244Pu, 247Cm), nuclear physics, and a search for long-lived super-heavy elements ( Z > 100). We are pursuing the environmental distribution of 236U, as a basis for geological applications of natural 236U.

Analysis and application of heavy isotopes in the environment

International Nuclear Information System (INIS)

Steier, Peter; Dellinger, Franz; Forstner, Oliver; Golser, Robin; Knie, Klaus; Kutschera, Walter; Priller, Alfred; Quinto, Francesca; Srncik, Michaela; Terrasi, Filippo; Vockenhuber, Christof; Wallner, Anton; Wallner, Gabriele; Wild, Eva Maria

2010-01-01

A growing number of AMS laboratories are pursuing applications of actinides. We discuss the basic requirements of the AMS technique of heavy (i.e., above ∼150 amu) isotopes, present the setup at the Vienna Environmental Research Accelerator (VERA) which is especially well suited for the isotope 236 U, and give a comparison with other AMS facilities. Special emphasis will be put on elaborating the effective detection limits for environmental samples with respect to other mass spectrometric methods. At VERA, we have carried out measurements for radiation protection and environmental monitoring ( 236 U, 239,240,241,242,244 Pu), astrophysics ( 182 Hf, 236 U, 244 Pu, 247 Cm), nuclear physics, and a search for long-lived super-heavy elements (Z > 100). We are pursuing the environmental distribution of 236 U, as a basis for geological applications of natural 236 U.

How Short-Lived Ikaite Affects Calcite Crystallization

OpenAIRE

Besselink, R; Rodriguez-Blanco, JD; Stawski, TM; Benning, LG; Tobler, DJ

2017-01-01

The pathways of CaCO3 crystallization are manifold, often involving one or several metastable amorphous or nanocrystalline intermediate phases. The presence of such intermediates is often overlooked, because they are short-lived and/or occur at small molar fractions. However, their occurrence does not just impact the mechanisms and pathways of formation of the final stable CaCO3 phase, but also affects their crystal size, shape, and structure. Here we document the presence of a short-lived in...

Actinide cross section data and inertial confinement fusion for long term waste disposal

International Nuclear Information System (INIS)

Meldner, H.

1979-01-01

Actinide cross section data at thermonuclear neutron energies are needed for the calculation of ICF pellet center burnup of fission reactor waste, viz. 14 MeV neutron fission of the very long-lived actinides that pose storage problems. A major advantage of pellet center burnup is safety: only milligrams of highly toxic and active material need to be present in the fusion chamber, whereas blanket burnup requires the continued presence of tons of actinides in a small volume. The actinide data tables required for Monte Carlo calculations of the burnup of 241 Am and 243 Am are discussed in connection with typical burnup reactor fusion and fission spectra. 2 figures

Compilation of actinide neutron nuclear data

International Nuclear Information System (INIS)

1979-01-01

The Swedish nuclear data committee has compiled a selected set of neutron cross section data for the 16 most important actinide isotopes. The aim of the report is to present available data in a comprehensible way to allow a comparison between different evaluated libraries and to judge about the reliability of these libraries from the experimental data. The data are given in graphical form below about 1 ev and above about 10 keV shile the 2200 m/s cross sections and resonance integrals are given in numerical form. (G.B.)

Plutonium and minor actinide transmutation by long irradiation in LWR

International Nuclear Information System (INIS)

Facchini, A.; Sanjust, V.

1993-01-01

An investigation was made on the conceptual possibility of burning in a thermal reactor MOX fuel together with special pins containing plutonium, minor actinides and long lived fission products, recovered from the reprocessing of previously irradiated MOX fuel and mixed with an inter matrix. Preliminary calculations showed that the long term radiotoxicity of the above special pins is reduced to reasonable levels when they are irradiated up to 20 divided-by 30 years, and cooled for some centuries. In particular, during the whole life such a reactor should be able to burn a considerable fraction of plutonium, minor actinides and long lived fission products recovered from the MOX fuel irradiated along the same period of time

Nuclear data of the major actinide fuel materials

Energy Technology Data Exchange (ETDEWEB)

Poenitz, W.P.; Saussure, G. De

1984-01-01

The effect of nuclear data of the major actinide fuel materials on the design accuracy, economics and safety of nuclear power systems is discussed. Since most of the data are measured relative to measurement standards, in particular the fission cross-section of /sup 235/U, data must be examined to ensure that absolute measurements and relative measurements are correctly handled. Nuclear data of fissile materials, fertile materials and minor plutonium isotopes are discussed.

Isotope production

Energy Technology Data Exchange (ETDEWEB)

Lewis, Dewi M.

1995-07-15

Some 2 0% of patients using radiopharmaceuticals receive injections of materials produced by cyclotrons. There are over 200 cyclotrons worldwide; around 35 are operated by commercial companies solely for the production of radio-pharmaceuticals with another 25 accelerators producing medically useful isotopes. These neutron-deficient isotopes are usually produced by proton bombardment. All commonly used medical isotopes can be generated by 'compact' cyclotrons with energies up to 40 MeV and beam intensities in the range 50 to 400 microamps. Specially designed target systems contain gram-quantities of highly enriched stable isotopes as starting materials. The targets can accommodate the high power densities of the proton beams and are designed for automated remote handling. The complete manufacturing cycle includes large-scale target production, isotope generation by cyclotron beam bombardment, radio-chemical extraction, pharmaceutical dispensing, raw material recovery, and labelling/packaging prior to the rapid delivery of these short-lived products. All these manufacturing steps adhere to the pharmaceutical industry standards of Good Manufacturing Practice (GMP). Unlike research accelerators, commercial cyclotrons are customized 'compact' machines usually supplied by specialist companies such as IBA (Belgium), EBCO (Canada) or Scanditronix (Sweden). The design criteria for these commercial cyclotrons are - small magnet dimensions, power-efficient operation of magnet and radiofrequency systems, high intensity extracted proton beams, well defined beam size and automated computer control. Performance requirements include rapid startup and shutdown, high reliability to support the daily production of short-lived isotopes and low maintenance to minimize the radiation dose to personnel. In 1987 a major step forward in meeting these exacting industrial requirements came when IBA, together with the University of Louvain-La-Neuve in Belgium, developed the Cyclone-30

Nuclear decay data: some applications and needs

International Nuclear Information System (INIS)

Reich, C.W.

1985-01-01

Nuclear decay data have broad relevance to a number of basic scientific disciplines as well as to many areas of technology. In this paper we discuss selected applications where decay data are making, or promise to make, important contributions. The following specific illustrations are discussed: the large body of precise new actinide-nuclide decay data produced through the work of the recently concluded IAEA Coordinated Research Program on the Measurement and Evaluation of Transactinium Isotope Nuclear Decay Data; the use of actinide-nuclide half-lives as reference standards in nuclear-data measurements; and the relevance of short-lived fission-product decay data to basic physics and reactor technology and some of the problems and challenges that they present to both theory and experiment

Actinide separation by electrorefining

International Nuclear Information System (INIS)

Fusselman, S.P.; Gay, R.L.; Grantham, L.F.; Grimmett, D.L.; Roy, J.J.; Inoue, T.; Hijikata, T.; Krueger, C.L.; Storvick, T.S.; Takahashi, N.

1995-01-01

TRUMP-S is a pyrochemical process being developed for the recovery of actinides from PUREX wastes. This paper describes development of the electrochemical partitioning step for recovery of actinides in the TRUMP-S process. The objectives are to remove 99 % of each actinide from PUREX wastes, with a product that is > 90 % actinides. Laboratory tests indicate that > 99 % of actinides can be removed in the electrochemical partitioning step. A dynamic (not equilibrium) process model predicts that 90 wt % product actinide content can be achieved through 99 % actinide removal. Accuracy of model simulation results were confirmed in tests with rare earths. (authors)

Moments and mean square charge radii of short-lived argon isotopes

CERN Document Server

Klein, A; Georg, U; Keim, M; Lievens, P; Neugart, R; Neuroth, M; Silverans, R E; Vermeeren, L

1996-01-01

We report on the measurement of optical isotope shifts for $^{32-40}$Ar and for $^{46}$Ar from which the changes in mean square nuclear charge radii across the N = 20 neutron shell closure are deducted. The investigations were carried out by collinear laser spectroscopy in fast beams of neutral argon atoms. The ultra-sensitive detection combines optical pumping, state-selective collisional ionization and counting of $\\beta$-radioactivity. By reaching far into the sd-shell, the results add new information to the systematics of radii in the calcium region (Z $\\approx$ 20). Contrary to all major neutron shell closures with N $\\geq$ 28, the N = 20 shell closure causes no significant slope change in the development of the radii. Information from the hyperfine structure of the odd-A isotopes includes includes the magnetic moments of $^{33}$Ar (I=1/2) and $^{39}$Ar (I=7/2), and the quadrupole moments of $^{35}$Ar, $^{37}$Ar (I=3/2) and $^{39}$Ar. The electromagnetic moments are compared to shell-model predictions fo...

Actinide partitioning-transmutation program final report. VI. Short-term risk analysis of reprocessing, refabrication, and transportation: summary

International Nuclear Information System (INIS)

Fullwood, R.; Jackson, R.

1980-03-01

A Partitioning-Transmutation (PT) fuel cycle is being compared to a Reference cycle employing conventional fuel-material recovery methods. The PT cycle uses enhanced recovery methods so that most of the long-lived actinides are recycled to nuclear power plants and transmuted thereby reducing the waste toxicity. This report compares the two fuel cycles on the basis of the short-term radiological and nonradiological risks. The accidental radiological risk to the public is analyzed by estimating the probabilities of sets of accidents; the consequences are calculated using the risk, which is RAC code. Routine radiological risks to the public are estimated from the calculated release amounts, also using the CRAC code. Radiological occupational risks are determined from prior experience, projected standards, and estimates of accident risk. Nonradiological risks are calculated from the number of personnel involved, historical experience, and epidemiological studies. Result of this analysis is that the short-term risk of PT is 2.9 times greater than that of the Reference cycle, primarily due to the larger amount of industry. The nonradiological risk which is about 150 times greater than the radiological risk. If the radiological risk is consdered alone, the ratio of PT to Reference risk is 3, composed as follows: radiological operations affecting the public 5, radiological operations affecting the workers 1.7, and radiological accidents affecting the public 1.4, all in the order of decreasing risk. The absolute risk as estimated for the fuel cycle portions considered in this report is 0.91 fatality/GWe-year for the PT cycle and 0.34 fatality/GWe-year for the reference cycle; this compares with 1.5 for nuclear and 150 for coal. All of the risks assumed here are associated with the production of one billion watts of electricity (GWe) per year

Trace analysis of actinides in the environment using resonance ionization mass spectrometry; Spurenanalyse von Aktiniden in der Umwelt mittels Resonanzionisations-Massenspektrometrie

Energy Technology Data Exchange (ETDEWEB)

Raeder, Sebastian

2011-04-12

In this work the resonant ionization of neutral atoms using laser radiation was applied and optimized for ultra-trace analysis of the actinides thorium, uranium, neptunium and plutonium. The sensitive detection of these actinides is a challange for the monitoring and quantification of radioactive releases from nuclear facilities. Using resonance ionization spectroscopy combined with a newly developed quadrupole-mass-spectrometer, numerous energy levels in the atomic structure of these actinides could be identified. With this knowledge efficient excitation schemes for the mentioned actinides could be identified and characterised. The applied in-source-ionization ensures for a high detection efficiency due to the good overlap of laser radiation with the atomic beam and allows therefore for a low sample consumption which is required for the analysis of radio nuclides. The selective excitation processes in the resonant ionization method supresses unwanted contaminations and was optimized for analytical detection of ultra-trace amounts in environmental samples as well as for determination of isotopic compositions. The efficient in-source-ionization combined with high power pulsed laser radiation allows for detections efficiency up to 1%. For plutonium detection limits in the range of 10{sup 4}-10{sup 5} atoms could be demonstrated for synthetic samples as well as for first environmental samples. The usage of narrow bandwidth continuous wave lasers in combination with a transversal overlap of the laser radiation and the free propagating atomic beam enable for resolving individual isotopic shifts of the resonant transitions. This results in a high selectivity against dominant neighboring isotopes but with a significant loss in detection efficiency. For the ultra-trace isotope {sup 236}U a detection limit down to 10{sup -9} for the isotope ratio N ({sup 236}U)/N ({sup 238}U) could be determined.

On the influence of the americium isotopic vector on the cooling time of minor actinides bearing blankets in fast reactors

Directory of Open Access Journals (Sweden)

Kooyman Timothée

2018-01-01

Full Text Available In the heterogeneous minor actinides transmutation approach, the nuclei to be transmuted are loaded in dedicated targets often located at the core periphery, so that long-lived heavy nuclides are turned into shorter-lived fission products by fission. To compensate for low flux level at the core periphery, the minor actinides content in the targets is set relatively high (around 20 at.%, which has a negative impact on the reprocessing of the targets due to their important decay heat level. After a complete analysis of the main contributors to the heat load of the irradiated targets, it is shown here that the choice of the reprocessing order of the various feeds of americium from the fuel cycle depends on the actual limit for fuel reprocessing. If reprocessing of hot targets is possible, it is more interesting to reprocess first the americium feed with a high 243Am content in order to limit the total cooling time of the targets, while if reprocessing of targets is limited by their decay heat, it is more interesting to wait for an increase in the 241Am content before loading the americium in the core. An optimization of the reprocessing order appears to lead to a decrease of the total cooling time by 15 years compared to a situation where all the americium feeds are mixed together when two feeds from SFR are considered with a high reprocessing limit.

Rapid column extraction method for actinides and strontium in fish and other animal tissue samples

International Nuclear Information System (INIS)

Maxwell III, S.L.; Faison, D.M.

2008-01-01

The analysis of actinides and radiostrontium in animal tissue samples is very important for environmental monitoring. There is a need to measure actinide isotopes and strontium with very low detection limits in animal tissue samples, including fish, deer, hogs, beef and shellfish. A new, rapid separation method has been developed that allows the measurement of plutonium, neptunium, uranium, americium, curium and strontium isotopes in large animal tissue samples (100-200 g) with high chemical recoveries and effective removal of matrix interferences. This method uses stacked TEVA Resin R , TRU Resin R and DGA Resin R cartridges from Eichrom Technologies (Darien, IL, USA) that allows the rapid separation of plutonium (Pu), neptunium (Np), uranium (U), americium (Am), and curium (Cm) using a single multi-stage column combined with alphaspectrometry. Strontium is collected on Sr Resin R from Eichrom Technologies (Darien, IL, USA). After acid digestion and furnace heating of the animal tissue samples, the actinides and 89/90 Sr are separated using column extraction chromatography. This method has been shown to be effective over a wide range of animal tissue matrices. Vacuum box cartridge technology with rapid flow rates is used to minimize sample preparation time. (author)

Analysis of the minority actinides transmutation in a sodium fast reactor with uniform load pattern by the MCNPX-CINDER code

International Nuclear Information System (INIS)

Ochoa Valero, R.; Garcia-Herranz, N.; Aragones, J. M.

2010-01-01

The aim of this study is to evaluate the minority actinides transmutation in sodium fast reactors (SFR) assuming a uniform load pattern. It is determined the isotopic evolution of the actinides along burn, and the evolution of the reactivity and the reactivity coefficients. For that, it is used the MCNPX neutron transport code coupled with the inventory code CINDER90.

Preparations and mechanism of hydrolysis of ([8]annulene)actinide compounds

International Nuclear Information System (INIS)

Moore, R.M. Jr.

1985-07-01

The mechanism of hydrolysis for bis[8]annulene actinide and lanthanide complexes has been studied in detail. The uranium complex, uranocene, decomposes with good pseudo-first order kinetics (in uranocene) in 1 M degassed solutions of H 2 O in THF. Decomposition of a series of aryl-substituted uranocenes demonstrates that the hydrolysis rate is dependent on the electronic nature of the substituent (Hammett rho value = 2.1, r 2 = 0.999), with electron-withdrawing groups increasing the rate. When D 2 O is substituted for H 2 O, kinetic isotope effects of 8 to 14 are found for a variety of substituted uranocenes. These results suggest a pre-equilibrium involving approach of a water molecule to the central metal, followed by rate determining proton transfer to the eight membered ring and rapid decomposition to products. Each of the four protonations of the complex has a significant isotope effect. The product ratio of cyclooctatriene isomers formed in the hydrolysis varies, depending on the central metal of the complex. However, the general mechanism of hydrolysis, established for uranocene, can be extended to the hydrolysis and alcoholysis of all the [8]annulene complexes of the lanthanides and actinides

Actinide analytical program for characterization of Hanford waste

International Nuclear Information System (INIS)

Johnson, S.J.; Winters, W.I.

1977-01-01

The objective of this program has been to develop faster, more accurate methods for the concentration and determination of actinides at their maximum permissible concentration (MPC) levels in a controlled zone. These analyses are needed to characterize various forms of Hanford high rad waste and to support characterization of products and effluents from new waste management processes. The most acceptable methods developed for the determination of 239 Pu, 238 Pu, 237 Np, 241 Am, and 243 Cm employ solvent extraction with the addition of tracer isotopes. Plutonium and neptunium are extracted from acidified waste solutions into Aliquat-336. Americium and curium are then extracted from the waste solution at the same acidity into dihexyl-N,N-diethylcarbamylmethylenephosphonate (DHDECMP). After back extraction into an aqueous matrix, these actinides are electrodeposited on steel disks for alpha energy analysis. Total uranium and total thorium are also isolated by solvent extraction and determined spectrophotometrically

Examination of minor actinide annihilation by BWR core

International Nuclear Information System (INIS)

Hida, Kazuki

1995-01-01

From the viewpoint of reducing burden for disposing high level waste generated from spent fuel, the examination of recycling minor actinide (MA) to reactors and reducing its accumulation has been advanced. In this study, the possibility of annihilation in the case of recycling it to a BWR was examined. The main MAs are 237 Np, 241 Am, 243 Am, 242 Cm, and 244 Cm. However, as for Cm isotopes, the half life is short, the amount of generation is small, and the rate of neutron emission is high, therefore, those are disposed as waste, and 237 Np, 241 Am and 243 Am were taken as the objects of recycling. In order to grasp the basic characteristics in the case of recycling MAs to a BWR, MAs were added to UO 2 fuel, MOX fuel and HCR fuel and burned, and the nuclear conversion characteristics were examined. As the result, it was found that they were converted to short half life nuclides, and as the neutron spectra were softer, the rate of annihilation was higher. In the case of recycling MAs by concentrating to a specific reactor, reactivity loss, the degree of uranium enrichment required for compensating reactivity, and the rate of MA annihilation were calculated. Based on these data, the MA recycling system was set up, and the rate of MA annihilation was evaluated. This is reported. (K.I.)

Fast molten salt reactor-transmuter for closing nuclear fuel cycle on minor actinides

International Nuclear Information System (INIS)

Dudnikov, A. A.; Alekseev, P. N.; Subbotin, S. A.

2007-01-01

Creation fast critical molten salt reactor for burning-out minor actinides and separate long-living fission products in the closed nuclear fuel cycle is the most perspective and actual direction. The reactor on melts salts - molten salt homogeneous reactor with the circulating fuel, working as burner and transmuter long-living radioactive nuclides in closed nuclear fuel cycle, can serve as an effective ecological cordon from contamination of the nature long-living radiotoxic nuclides. High-flux fast critical molten-salt nuclear reactors in structure of the closed nuclear fuel cycle of the future nuclear power can effectively burning-out / transmute dangerous long-living radioactive nuclides, make radioisotopes, partially utilize plutonium and produce thermal and electric energy. Such reactor allows solving the problems constraining development of large-scale nuclear power, including fueling, minimization of radioactive waste and non-proliferation. Burning minor actinides in molten salt reactor is capable to facilitate work solid fuel power reactors in system NP with the closed nuclear fuel cycle and to reduce transient losses at processing and fabrications fuel pins. At substantiation MSR-transmuter/burner as solvents fuel nuclides for molten-salt reactors various salts were examined, for example: LiF - BeF2; NaF - LiF - BeF2; NaF-LiF ; NaF-ZrF4 ; LiF-NaF -KF; NaCl. RRC 'Kurchatov institute' together with other employees have developed the basic design reactor installations with molten salt reactor - burner long-living nuclides for fluoride fuel composition with the limited solubility minor actinides (MAF3 10 mol %) allows to develop in some times more effective molten salt reactor with fast neutron spectrum - burner/ transmuter of the long-living radioactive waste. In high-flux fast reactors on melts salts within a year it is possible to burn ∼300 kg minor actinides per 1 GW thermal power of reactor. The technical and economic estimation given power

Thermal neutrons core concepts for minor actinides inventory reduction

International Nuclear Information System (INIS)

Huang, Shio-Ling

1996-01-01

The goal of this thesis is to propose a solution to the problem of reducing the inventory of Minor Actinides, discharged from PWR spent fuel, in the framework of a Separation/ Transmutation strategy. The solution envisaged is based on the utilisation of Pressurised Water Reactors (PWR), of the same type as those used to produce energy. The suggested solution is original and based on a special Assembly ANDIAMO dedicated to transmutation, where Actinide incineration is performed with the help of a fissile support in a once-through strategy. During this study, we have also tackled the impact of some parameters which so far have been less carefully studied (like the unavoidable presence of Lanthanides in fuel containing Am and Cm and the consequences on the cycle parameters with Actinide recycle). Moreover, we have carried out a sensitivity study in order to analysis the impact of nuclear data uncertainties on some important parameters of the reactor (reactivity coefficients) and on the isotopic concentration. This original study allows us to assess the accuracy of the results, of the presented tendencies and of the propositions made in the present thesis. (author) [fr

''Sleeping reactor'' irradiations: Shutdown reactor determination of short-lived activation products

International Nuclear Information System (INIS)

Jerde, E.A.; Glasgow, D.C.

1998-01-01

At the High-Flux Isotope Reactor (HFIR) at the Oak Ridge National Laboratory, the principal irradiation system has a thermal neutron flux (φ) of ∼ 4 x 10 14 n/cm 2 · s, permitting the detection of elements via irradiation of 60 s or less. Irradiations of 6 or 7 s are acceptable for detection of elements with half-lives of as little as 30 min. However, important elements such as Al, Mg, Ti, and V have half-lives of only a few minutes. At HFIR, these can be determined with irradiation times of ∼ 6 s, but the requirement of immediate counting leads to increased exposure to the high activity produced by irradiation in the high flux. In addition, pneumatic system timing uncertainties (about ± 0.5 s) make irradiations of 9 Be(γ,n) 8 Be, the gamma rays principally originating in the spent fuel. Upon reactor SCRAM, the flux drops to ∼ 1 x 10 10 n/cm 2 · s within 1 h. By the time the fuel elements are removed, the flux has dropped to ∼ 6 x 10 8 . Such fluxes are ideal for the determination of short-lived elements such as Al, Ti, Mg, and V. An important feature of the sleeping reactor is a flux that is not constant

Stable isotope enrichment: Current and future potential

International Nuclear Information System (INIS)

Tracy, J.G.; Aaron, W.S.

1992-01-01

Oak Ridge National Laboratory (ORNL) operates the Isotope Enrichment Facility for the purpose of providing enriched stable isotopes, selected radioactive isotopes (including the actinides), and isotope-related materials and services for use in various research applications. ORNL is responsible for isotope enrichment and the distribution of approximately 225 nongaseous stable isotopes from 50 multi-isotopic elements. Many enriched isotope products are of prime importance in the fabrication of nuclear targets and the subsequent production of special radionuclides. State-of-the-art techniques to achieve special isotopic, chemical, and physical requirements are performed at ORNL This report describes the status and capabilities of the Isotope Enrichment Facility and the Isotope Research Materials Laboratory as well as emphasizing potential advancements in enrichment capabilities

Stable isotope enrichment - current and future potential

International Nuclear Information System (INIS)

Tracy, J.G.; Aaron, W.S.

1993-01-01

Oak Ridge National Laboratory (ORNL) operates the Isotope Enrichment Facility for the purpose of providing enriched stable isotopes, selected radioactive isotopes (including the actinides), and isotope-related materials and services for use in various research applications. ORNL is responsible for isotope enrichment and the distribution of approximately 225 nongaseous stable isotopes from 50 multi-isotopic elements. Many enriched isotope products are of prime importance in the fabrication of nuclear targets and the subsequent production of special radionuclides. State-of-the-art techniques to achieve special isotopic, chemical, and physical requirements are performed at ORNL. This report describes the status and capabilities of the Isotope Enrichment Facility and the Isotope Research Materials Laboratory as well as emphasizing potential advancements in enrichment capabilities. (orig.)

Sensitivity of DF-ICP-MS, PERALS and alpha-spectrometry for the determination of actinides. A comparison

International Nuclear Information System (INIS)

Ayranov, M.; Kraehenbuehl, U.

2009-01-01

We applied three techniques (DF-ICP-MS, PERALS and alpha-spectrometry) for the determination of minor actinides at environmental levels. For each method the limit of detection and the resolution were estimated in order to study the content and isotopic composition of the actinides. Two international reference materials, IAEA-135 (Irish Sea Sediment) and IAEA-300 (Baltic Sea sediment) were analyzed for activity concentrations of 238 Pu, 239 Pu, 240 Pu, 241 Pu and 241 Am. The sensitivities of the three determination techniques were compared. (author)

Standard practice for alternate actinide calibration for inductively coupled plasma-mass spectrometry

CERN Document Server

American Society for Testing and Materials. Philadelphia

2004-01-01

1.1 This practice provides guidance for an alternate linear calibration for the determination of selected actinide isotopes in appropriately prepared aqueous solutions by Inductively Coupled Plasma-Mass Spectrometry (ICP-MS). This alternate calibration is mass bias adjusted using thorium-232 (232Th) and uranium-238 (238U) standards. One of the benefits of this standard practice is the ability to calibrate for the analysis of highly radioactive actinides using calibration standards at much lower specific activities. Environmental laboratories may find this standard practice useful if facilities are not available to handle the highly radioactive standards of the individual actinides of interest. 1.2 The instrument response for a series of determinations of known concentration of 232Th and 238U defines the mass versus response relationship. For each standard concentration, the slope of the line defined by 232Th and 238U is used to derive linear calibration curves for each mass of interest using interference equ...

Separation and purification of short lived fission products from irradiated uranium

International Nuclear Information System (INIS)

Balasubramanian, K.R.; Rao, K.L.N.; Mathai, C.; Varma, R.N.; Dhiwar, V.I.; Saxena, S.K.

1991-01-01

Fission produced radioisotopes like 95 Zr, 140 Ba, 103 Ru, 89 Sr and 91 Y whose half lives are less than 1 year find a wide variety of applications in the fields of industry, medicine and research. Isotope Division, BARC has been supplying these isotopes in hudreds of mCi amounts during the past several years. A new method for the sequential separation of these isotopes from irradiated uranium has been developed based on synthetic inorganic exchangers like stannic phosphate, polyphospho antimonic acid, hydrous manganese dioxide, etc. This report describes the new flow sheet worked out and adopted for the regular processing of these isotopes at hundreds of milli curie amounts. (author). 19 refs., 4 tabs. , 1 fig

The uncertainty analysis of a liquid metal reactor for burning minor actinides from light water reactors

Energy Technology Data Exchange (ETDEWEB)

Choi, Hang Bok [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1999-12-31

The neutronics analysis of a liquid metal reactor for burning minor actinides has shown that uncertainties in the nuclear data of several key minor actinide isotopes can introduce large uncertainties in the predicted performance of the core. A comprehensive sensitivity and uncertainty analysis was performed on a 1200 MWth actinide burner designed for a low burnup reactivity swing, negative doppler coefficient, and low sodium void worth. Sensitivities were generated using depletion perturbation methods for the equilibrium cycle of the reactor and covariance data was taken ENDF-B/V and other published sources. The relative uncertainties in the burnup swing, doppler coefficient, and void worth were conservatively estimated to be 180%, 97%, and 46%, respectively. 5 refs., 1 fig., 3 tabs. (Author)

The uncertainty analysis of a liquid metal reactor for burning minor actinides from light water reactors

Energy Technology Data Exchange (ETDEWEB)

Choi, Hang Bok [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1998-12-31

The neutronics analysis of a liquid metal reactor for burning minor actinides has shown that uncertainties in the nuclear data of several key minor actinide isotopes can introduce large uncertainties in the predicted performance of the core. A comprehensive sensitivity and uncertainty analysis was performed on a 1200 MWth actinide burner designed for a low burnup reactivity swing, negative doppler coefficient, and low sodium void worth. Sensitivities were generated using depletion perturbation methods for the equilibrium cycle of the reactor and covariance data was taken ENDF-B/V and other published sources. The relative uncertainties in the burnup swing, doppler coefficient, and void worth were conservatively estimated to be 180%, 97%, and 46%, respectively. 5 refs., 1 fig., 3 tabs. (Author)

Actinide metals

Energy Technology Data Exchange (ETDEWEB)

Brown, Paul L. [Geochem Australia, Kiama, NSW (Australia); Ekberg, Christian [Chalmers Univ. of Technology, Goeteborg (Sweden). Nuclear Chemistry/Industrial Materials Recycling

2016-07-01

All isotopes of actinium are radioactive and exist in aqueous solution only in the trivalent state. There have been very few studies on the hydrolytic reactions of actinium(III). The hydrolysis reactions for uranium would only be important in alkaline pH conditions. Thermodynamic parameters for the hydrolysis species of uranium(VI) and its oxide and hydroxide phases can be determined from the stability and solubility constants. The hydrolytic behaviour of neptunium(VI) is quite similar to that of uranium(VI). The solubility constant of NpO{sub 2}OH(am) has been reported a number of times for both zero ionic strength and in fixed ionic strength media. Americium can form four oxidation states in aqueous solution, namely trivalent, tetravalent, pentavalent and hexavalent. Desire, Hussonnois and Guillaumont determined stability constants for the species AmOH{sup 2+} for the actinides, plutonium(III), americium(III), curium(III), berkelium(III) and californium(III) using a solvent extraction technique.

Actinide metals

International Nuclear Information System (INIS)

Brown, Paul L.; Ekberg, Christian

2016-01-01

All isotopes of actinium are radioactive and exist in aqueous solution only in the trivalent state. There have been very few studies on the hydrolytic reactions of actinium(III). The hydrolysis reactions for uranium would only be important in alkaline pH conditions. Thermodynamic parameters for the hydrolysis species of uranium(VI) and its oxide and hydroxide phases can be determined from the stability and solubility constants. The hydrolytic behaviour of neptunium(VI) is quite similar to that of uranium(VI). The solubility constant of NpO 2 OH(am) has been reported a number of times for both zero ionic strength and in fixed ionic strength media. Americium can form four oxidation states in aqueous solution, namely trivalent, tetravalent, pentavalent and hexavalent. Desire, Hussonnois and Guillaumont determined stability constants for the species AmOH 2+ for the actinides, plutonium(III), americium(III), curium(III), berkelium(III) and californium(III) using a solvent extraction technique.

Separation of gallium and actinides in plutonium nuclear materials by extraction chromatography

International Nuclear Information System (INIS)

Eitrheim, E.S.; Knight, A.W.

2015-01-01

Analysis of stable gallium in nuclear materials has applications in nuclear fuel characterization and nuclear forensics. The use of positron-emitting gallium isotope 68 Ga as a tracer for Ga recoveries for analyses in materials containing actinides was explored. A radiochemical method for the separation of Ga, Pu, U, Th, and Am using commercially-available extraction chromatography resins was developed and evaluated. The method effectively allows precise determination of Ga yield (97 ± 3 %) in the analysis of stable Ga (spike recovery 101 ± 1 %) and radioactive Pu (radiochemical yield, 82 ± 10 %; spike recovery, 96 ± 3 %), while also providing pure elemental fractions of other actinides relevant to materials encountered in the analysis Pu-containing materials. (author)

Actinide oxide photodiode and nuclear battery

Energy Technology Data Exchange (ETDEWEB)

Sykora, Milan; Usov, Igor

2017-12-05

Photodiodes and nuclear batteries may utilize actinide oxides, such a uranium oxide. An actinide oxide photodiode may include a first actinide oxide layer and a second actinide oxide layer deposited on the first actinide oxide layer. The first actinide oxide layer may be n-doped or p-doped. The second actinide oxide layer may be p-doped when the first actinide oxide layer is n-doped, and the second actinide oxide layer may be n-doped when the first actinide oxide layer is p-doped. The first actinide oxide layer and the second actinide oxide layer may form a p/n junction therebetween. Photodiodes including actinide oxides are better light absorbers, can be used in thinner films, and are more thermally stable than silicon, germanium, and gallium arsenide.

Thermodynamic Properties of Actinides and Actinide Compounds

Science.gov (United States)

Konings, Rudy J. M.; Morss, Lester R.; Fuger, Jean

The necessity of obtaining accurate thermodynamic quantities for the actinide elements and their compounds was recognized at the outset of the Manhattan Project, when a dedicated team of scientists and engineers initiated the program to exploit nuclear energy for military purposes. Since the end of World War II, both fundamental and applied objectives have motivated a great deal of further study of actinide thermodynamics. This chapter brings together many research papers and critical reviews on this subject. It also seeks to assess, to systematize, and to predict important properties of the actinide elements, ions, and compounds, especially for species in which there is significant interest and for which there is an experimental basis for the prediction.

Optimisation and application of ICP-MS and alpha-spectrometry for determination of isotopic ratios of depleted uranium and plutonium in samples collected in Kosovo

OpenAIRE

Boulyga, S. F.; Testa, C.; Desideri, D.; Becker, J. S.

2001-01-01

The determination of environmental contamination with natural and artificial actinide isotopes and evaluation of their source requires precise isotopic determination of actinides, above all uranium and plutonium. This can be achieved by alpha spectrometry or by inductively coupled plasma mass spectrometry (ICP-MS) after chemical separation of actinides. The performance of a sector-field ICP-MS (ICP-SFMS) coupled to a low-flow micronebulizer with a membrane desolvation unit, "Aridus'', was stu...

Short-term coral bleaching is not recorded by skeletal boron isotopes.

Science.gov (United States)

Schoepf, Verena; McCulloch, Malcolm T; Warner, Mark E; Levas, Stephen J; Matsui, Yohei; Aschaffenburg, Matthew D; Grottoli, Andréa G

2014-01-01

Coral skeletal boron isotopes have been established as a proxy for seawater pH, yet it remains unclear if and how this proxy is affected by seawater temperature. Specifically, it has never been directly tested whether coral bleaching caused by high water temperatures influences coral boron isotopes. Here we report the results from a controlled bleaching experiment conducted on the Caribbean corals Porites divaricata, Porites astreoides, and Orbicella faveolata. Stable boron (δ11B), carbon (δ13C), oxygen (δ18O) isotopes, Sr/Ca, Mg/Ca, U/Ca, and Ba/Ca ratios, as well as chlorophyll a concentrations and calcification rates were measured on coral skeletal material corresponding to the period during and immediately after the elevated temperature treatment and again after 6 weeks of recovery on the reef. We show that under these conditions, coral bleaching did not affect the boron isotopic signature in any coral species tested, despite significant changes in coral physiology. This contradicts published findings from coral cores, where significant decreases in boron isotopes were interpreted as corresponding to times of known mass bleaching events. In contrast, δ13C and δ18O exhibited major enrichment corresponding to decreases in calcification rates associated with bleaching. Sr/Ca of bleached corals did not consistently record the 1.2°C difference in seawater temperature during the bleaching treatment, or alternatively show a consistent increase due to impaired photosynthesis and calcification. Mg/Ca, U/Ca, and Ba/Ca were affected by coral bleaching in some of the coral species, but the observed patterns could not be satisfactorily explained by temperature dependence or changes in coral physiology. This demonstrates that coral boron isotopes do not record short-term bleaching events, and therefore cannot be used as a proxy for past bleaching events. The robustness of coral boron isotopes to changes in coral physiology, however, suggests that reconstruction of

Behaviour of short-lived fission products within operating UO2 fuel elements

International Nuclear Information System (INIS)

Hastings, I.J.; Hunt, C.E.L.; Lipsett, J.J.

1983-01-01

We have carried out experiments using a ''sweep gas'' technique to determine the behaviour of short-lived fission products within operating, intact UO 2 fuel elements. The Zircaloy-4-clad elements were 500 mm long and contained fuel of density 10.65-10.71 Mg/m 3 . A He-2% H 2 carrier gas swept gaseous or volatile fission products out of the operating fuel element past a gamma spectrometer for measurement. In tests at linear powers of 45 and 60 kW/m to maximum burnups of 70 MW.h/kg U, the species measured directly at the spectrometer were generally the short-lived xenons and kryptons. We did not observe iodine or bromine during normal operation. However, we have deduced the behaviour of I-133 and I-135 from the decay of Xe-133 and Xe-135 during reactor shutdowns. Plots of R/B (released/born) against lambda (decay constant) or effective lambda for all isotopes observed at 45 and 60 kW/m show that a line of slope -0.5, corresponding with diffusion kinetics, is a good fit to the measured xenon and krypton data. Our inferred release of iodine fits the same line. From this we can extrapolate to an R/B for I-131 of about 5x10 -3 . The ANS 5.4 release correlation gives calculated results in good agreement with our measurements. (author)

Actinide separation chemistry in nuclear waste streams and materials

International Nuclear Information System (INIS)

1997-12-01

The separation of actinide elements from various waste materials, produced either in nuclear fuel cycles or in past nuclear weapons production, represents a significant issue facing developed countries. Improvements in the efficiencies of the separation processes can be expected to occur as a result of better knowledge of the elements in these complex matrices. The Nuclear Science Committee of the OECD/NEA has established a task force of experts in actinide separation chemistry to review current and developing separation techniques and chemical processes. The report consist of eight chapters. In Chapter 1 the importance of actinide separation chemistry in the fields of waste management and its background are summarized.In Chapter 2 the types of waste streams are classified according to their relative importance, by physical form and by source of actinides. The basic data of actinide chemical thermodynamics, such as oxidation states, hydrolysis, complexation, sorption, Gibbs energies of formation, and volatility, were collected and are presented in Chapter 3. Actinide analyses related to separation processes are also mentioned in this chapter. The state of the art of actinide separation chemistry is classified in three groups, including hydrometallurgy, pyrochemical process and process based on fields, and is described in Chapter 4 along with the relationship of kinetics to separations. In Chapter 5 basic chemistry research needs and the inherent limitation on separation processes are discussed. Prioritization of research and development is discussed in Chapter 6 in the context of several attributes of waste management problems. These attributes include: mass or volume of waste; concentration of the actinide in the waste; expected difficulty of treating the wastes; short-term hazard of the waste; long-term hazard of the waste; projected cost of treatment; amount of secondary waste. Based on the priority, recommendations were made for the direction of future research

Actinide separation chemistry in nuclear waste streams and materials

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-01

The separation of actinide elements from various waste materials, produced either in nuclear fuel cycles or in past nuclear weapons production, represents a significant issue facing developed countries. Improvements in the efficiencies of the separation processes can be expected to occur as a result of better knowledge of the elements in these complex matrices. The Nuclear Science Committee of the OECD/NEA has established a task force of experts in actinide separation chemistry to review current and developing separation techniques and chemical processes. The report consist of eight chapters. In Chapter 1 the importance of actinide separation chemistry in the fields of waste management and its background are summarized.In Chapter 2 the types of waste streams are classified according to their relative importance, by physical form and by source of actinides. The basic data of actinide chemical thermodynamics, such as oxidation states, hydrolysis, complexation, sorption, Gibbs energies of formation, and volatility, were collected and are presented in Chapter 3. Actinide analyses related to separation processes are also mentioned in this chapter. The state of the art of actinide separation chemistry is classified in three groups, including hydrometallurgy, pyrochemical process and process based on fields, and is described in Chapter 4 along with the relationship of kinetics to separations. In Chapter 5 basic chemistry research needs and the inherent limitation on separation processes are discussed. Prioritization of research and development is discussed in Chapter 6 in the context of several attributes of waste management problems. These attributes include: mass or volume of waste; concentration of the actinide in the waste; expected difficulty of treating the wastes; short-term hazard of the waste; long-term hazard of the waste; projected cost of treatment; amount of secondary waste. Based on the priority, recommendations were made for the direction of future research

Positron range in PET imaging: non-conventional isotopes

International Nuclear Information System (INIS)

Jødal, L; Le Loirec, C; Champion, C

2014-01-01

In addition to conventional short-lived radionuclides, longer-lived isotopes are becoming increasingly important to positron emission tomography (PET). The longer half-life both allows for circumvention of the in-house production of radionuclides, and expands the spectrum of physiological processes amenable to PET imaging, including processes with prohibitively slow kinetics for investigation with short-lived radiotracers. However, many of these radionuclides emit ‘high-energy’ positrons and gamma rays which affect the spatial resolution and quantitative accuracy of PET images. The objective of the present work is to investigate the positron range distribution for some of these long-lived isotopes. Based on existing Monte Carlo simulations of positron interactions in water, the probability distribution of the line of response displacement have been empirically described by means of analytic displacement functions. Relevant distributions have been derived for the isotopes 22 Na, 52 Mn, 89 Zr, 45 Ti, 51 Mn, 94m Tc, 52m Mn, 38 K, 64 Cu, 86 Y, 124 I, and 120 I. It was found that the distribution functions previously found for a series of conventional isotopes (Jødal et al 2012 Phys. Med. Bio. 57 3931–43), were also applicable to these non-conventional isotopes, except that for 120 I, 124 I, 89 Zr, 52 Mn, and 64 Cu, parameters in the formulae were less well predicted by mean positron energy alone. Both conventional and non-conventional range distributions can be described by relatively simple analytic expressions. The results will be applicable to image-reconstruction software to improve the resolution. (paper)

Analysis of the transmutational characteristics of a novel molten salt reactor concept

International Nuclear Information System (INIS)

Csom, Gy.; Feher, S.; Szieberth, M.

2001-01-01

One of the arguments most frequently brought up by the opponents of the utilization of nuclear energy is the requirement that the radioactive waste and the long-lived radioisotopes accumulated in the spent fuel should be isolated for a very long time from the biosphere. The solution is the elimination of long-lived actinides (plutonium isotopes and minor actinides) and long-lived fission products by transforming (transmuting) them into short-lived or stable nuclei. The high neutron flux required for transmutation can be realized in nuclear installations. these may be conventional therma; and fast reactors, furthermore dedicated devices, namely thermal and fast reactors and accelerator driven subcritical systems (ADSs), which are specifically designed for this purpose. Some of the most promising systems are the molten salt reactors and subcritical systems, in which the fuel and material to be transmuted circulate dissolved in some molten salt. In the present paper this transmutational device, as well as recommendations for the improvement are discussed in detail (Authors)

Actinide transmutation in nuclear reactors

International Nuclear Information System (INIS)

Bultman, J.H.

1995-01-01

An optimization method is developed to maximize the burning capability of the ALMR while complying with all constraints imposed on the design for reliability and safety. This method leads to a maximal transuranics enrichment, which is being limited by constraints on reactivity. The enrichment can be raised by using the neutrons less efficiently by increasing leakage from the fuel. With the developed optimization method, a metallic and an oxide fueled ALMR were optimized. Both reactors perform equally well considering the burning of transuranics. However, metallic fuel has a much higher heat conductivity coefficient, which in general leads to better safety characteristics. In search of a more effective waste transmuter, a modified Molten Salt Reactor was designed. A MSR operates on a liquid fuel salt which makes continuous refueling possible, eliminating the issue of the burnup reactivity loss. Also, a prompt negative reactivity feedback is possible for an overmoderated reactor design, even when the Doppler coefficient is positive, due to the fuel expansion with fuel temperature increase. Furthermore, the molten salt fuel can be reprocessed based on a reduction process which is not sensitive to the short-lived spontaneously fissioning actinides. (orig./HP)

Actinide transmutation in nuclear reactors

Energy Technology Data Exchange (ETDEWEB)

Bultman, J H

1995-01-17

An optimization method is developed to maximize the burning capability of the ALMR while complying with all constraints imposed on the design for reliability and safety. This method leads to a maximal transuranics enrichment, which is being limited by constraints on reactivity. The enrichment can be raised by using the neutrons less efficiently by increasing leakage from the fuel. With the developed optimization method, a metallic and an oxide fueled ALMR were optimized. Both reactors perform equally well considering the burning of transuranics. However, metallic fuel has a much higher heat conductivity coefficient, which in general leads to better safety characteristics. In search of a more effective waste transmuter, a modified Molten Salt Reactor was designed. A MSR operates on a liquid fuel salt which makes continuous refueling possible, eliminating the issue of the burnup reactivity loss. Also, a prompt negative reactivity feedback is possible for an overmoderated reactor design, even when the Doppler coefficient is positive, due to the fuel expansion with fuel temperature increase. Furthermore, the molten salt fuel can be reprocessed based on a reduction process which is not sensitive to the short-lived spontaneously fissioning actinides. (orig./HP).

Heterogeneous all actinide recycling in LWR all actinide cycle closure concept

International Nuclear Information System (INIS)

Tondinelli, Luciano

1980-01-01

A project for the elimination of transuranium elements (Waste Actinides, WA) by neutron transmutation is developed in a commercial BWR with U-Pu (Fuel Actinides, FA) recycle. The project is based on the All Actinide Cycle Closure concept: 1) closure of the 'back end' of the fuel cycle, U-Pu coprocessing, 2) waste actinide disposal by neutron transmutation. The reactor core consists of Pu-island fuel assemblies containing WAs in target pins. Two parallel reprocessing lines for FAs and WAs are provided. Mass balance, hazard measure, spontaneous activity during 10 recycles are calculated. Conclusions are: the reduction in All Actinide inventory achieved by Heterogeneous All Actinide Recycling is on the order of 83% after 10 recycles. The U235 enrichment needed for a constant end of cycle reactivity decreases for increasing number of recycles after the 4th recycle. A diffusion-burnup calculation of the pin power peak factors in the fuel assembly shows that design limits can be satisfied. A strong effort should be devoted to the solution of the problems related to high values of spontaneous emission by the target pins

Actinides-1981

International Nuclear Information System (INIS)

1981-09-01

Abstracts of 134 papers which were presented at the Actinides-1981 conference are presented. Approximately half of these papers deal with electronic structure of the actinides. Others deal with solid state chemistry, nuclear physic, thermodynamic properties, solution chemistry, and applied chemistry

Actinides-1981

Energy Technology Data Exchange (ETDEWEB)

1981-09-01

Abstracts of 134 papers which were presented at the Actinides-1981 conference are presented. Approximately half of these papers deal with electronic structure of the actinides. Others deal with solid state chemistry, nuclear physic, thermodynamic properties, solution chemistry, and applied chemistry.

Laser spectroscopy and beta-NMR measurements of short-lived Mg isotopes

CERN Document Server

Kowalska, M

2005-01-01

The feasibility of studying the neutron-rich 29Mg, 31Mg and 33Mg isotopes has been demonstrated with the laser and beta-NMR spectroscopy setup at ISOLDE/CERN. The values of the magnetic moment and the nuclear spin of 31Mg are reported and reveal an intruder ground state. This proves the weakening of N=20 shell gap and places this nucleus inside the so called "island of inversion". The experimental setup and technique, as well as the results, are presented.

Behavior of actinides in the Integral Fast Reactor fuel cycle

Energy Technology Data Exchange (ETDEWEB)

Courtney, J.C. [Louisiana State Univ., Baton Rouge, LA (United States). Nuclear Science Center; Lineberry, M.J. [Argonne National Lab., Idaho Falls, ID (United States). Technology Development Div.

1994-06-01

The Integral Fast Reactor (IFR) under development by Argonne National Laboratory uses metallic fuels instead of ceramics. This allows electrorefining of spent fuels and presents opportunities for recycling minor actinide elements. Four minor actinides ({sup 237}Np, {sup 240}Pu, {sup 241}Am, and {sup 243}Am) determine the waste storage requirements of spent fuel from all types of fission reactors. These nuclides behave the same as uranium and other plutonium isotopes in electrorefining, so they can be recycled back to the reactor without elaborate chemical processing. An experiment has been designed to demonstrate the effectiveness of the high-energy neutron spectra of the IFR in consuming these four nuclides and plutonium. Eighteen sets of seven actinide and five light metal targets have been selected for ten day exposure in the Experimental Breeder Reactor-2 which serves as a prototype of the IFR. Post-irradiation analyses of the exposed targets by gamma, alpha, and mass spectroscopy are used to determine nuclear reaction-rates and neutron spectra. These experimental data increase the authors` confidence in their ability to predict reaction rates in candidate IFR designs using a variety of neutron transport and diffusion programs.

Actinide behavior in the Integral Fast Reactor. Final project report

Energy Technology Data Exchange (ETDEWEB)

Courtney, J.C.

1994-11-01

The Integral Fast Reactor (IFR) under development by Argonne National Laboratory uses metallic fuels instead of ceramics. This allows electrorefining of spent fuels and presents opportunities for recycling minor actinide elements. Four minor actinides ({sup 237}Np, {sup 240}Pu, {sup 241}Am, and {sup 243}Am) determine the waste storage requirements of spent fuel from all types of fission reactors. These nuclides behave the same as uranium and other plutonium isotopes in electrorefining, so they can be recycled back to the reactor without elaborate chemical processing. An experiment has been designed to demonstrate the effectiveness of the high-energy neutron spectra of the IFR in consuming these four nuclides and weapons grade plutonium. Eighteen sets of seven actinide and five light metal targets have been selected for seven day exposure in the Experimental Breeder Reactor-II which serves as a prototype of the IFR. Post-irradiation analyses of the exposed targets by gamma, alpha, and mass spectroscopy are used to determine nuclear reaction rates and neutron spectra. These experimental data increase the authors confidence in their ability to predict reaction rates in candidate IFR designs using a variety of neutron transport and diffusion programs.

Actinide behavior in the Integral Fast Reactor. Final project report

International Nuclear Information System (INIS)

Courtney, J.C.

1994-11-01

The Integral Fast Reactor (IFR) under development by Argonne National Laboratory uses metallic fuels instead of ceramics. This allows electrorefining of spent fuels and presents opportunities for recycling minor actinide elements. Four minor actinides ( 237 Np, 240 Pu, 241 Am, and 243 Am) determine the waste storage requirements of spent fuel from all types of fission reactors. These nuclides behave the same as uranium and other plutonium isotopes in electrorefining, so they can be recycled back to the reactor without elaborate chemical processing. An experiment has been designed to demonstrate the effectiveness of the high-energy neutron spectra of the IFR in consuming these four nuclides and weapons grade plutonium. Eighteen sets of seven actinide and five light metal targets have been selected for seven day exposure in the Experimental Breeder Reactor-II which serves as a prototype of the IFR. Post-irradiation analyses of the exposed targets by gamma, alpha, and mass spectroscopy are used to determine nuclear reaction rates and neutron spectra. These experimental data increase the authors confidence in their ability to predict reaction rates in candidate IFR designs using a variety of neutron transport and diffusion programs

Behavior of actinides in the Integral Fast Reactor fuel cycle

International Nuclear Information System (INIS)

Courtney, J.C.; Lineberry, M.J.

1994-01-01

The Integral Fast Reactor (IFR) under development by Argonne National Laboratory uses metallic fuels instead of ceramics. This allows electrorefining of spent fuels and presents opportunities for recycling minor actinide elements. Four minor actinides ( 237 Np, 240 Pu, 241 Am, and 243 Am) determine the waste storage requirements of spent fuel from all types of fission reactors. These nuclides behave the same as uranium and other plutonium isotopes in electrorefining, so they can be recycled back to the reactor without elaborate chemical processing. An experiment has been designed to demonstrate the effectiveness of the high-energy neutron spectra of the IFR in consuming these four nuclides and plutonium. Eighteen sets of seven actinide and five light metal targets have been selected for ten day exposure in the Experimental Breeder Reactor-2 which serves as a prototype of the IFR. Post-irradiation analyses of the exposed targets by gamma, alpha, and mass spectroscopy are used to determine nuclear reaction-rates and neutron spectra. These experimental data increase the authors' confidence in their ability to predict reaction rates in candidate IFR designs using a variety of neutron transport and diffusion programs

Comparison calculations for an accelerator-driven minor actinide burner

International Nuclear Information System (INIS)

2002-01-01

International interest in accelerator-driven systems (ADS) has recently been increasing in view of the important role that these systems may play as efficient minor actinide and long-lived fission-product (LLFP) burners and/or energy producers with an enhanced safety potential. However, the current methods of analysis and nuclear data for minor actinide and LLFP burners are not as well established as those for conventionally fuelled reactor systems. Hence, in 1999, the OECD/NEA Nuclear Science Committee organised a benchmark exercise for an accelerator-driven minor actinide burner to check the performances of reactor codes and nuclear data for ADS with unconventional fuel and coolant. The benchmark model was a lead-bismuth-cooled subcritical system driven by a beam of 1 GeV protons. This report provides an analysis of the results supplied by seven participants from eight countries. The analysis reveals significant differences in important neutronic parameters, indicating a need for further investigation of the nuclear data, especially minor actinide data, as well as the calculation methods. This report will be of particular interest to reactor physicists and nuclear data evaluators developing nuclear systems for nuclear waste management. (authors)

Short-lived radiopharmaceutical development at E.R. Squibb and Sons, Inc

International Nuclear Information System (INIS)

Loberg, M.D.

1985-01-01

This paper describes the present status and future plans of E.R. Squibb and Sons, Inc. as they relate to the development of short-lived radiopharmaceuticals. The advantages of short-lived radiopharmaceuticals are summarized as are the problems inherent in their manufacture, quality control, and distribution. The nuclear generator is advocated as the best means of distributing short-lived radiopharmaceuticals. The E.R. Squibb and Sons work with the 82 Sr → 82 Rb generator is summarized

Measurements of beta-decay half-lives of short-lived nuclei

Energy Technology Data Exchange (ETDEWEB)

Hirose, T.; Tsurita, Y.; Yamamoto, H.; Kawade, K. [Nagoya Univ. (Japan); Iida, T.; Takahashi, A.; Kasugai, Y.; Ikeda, Y.

1997-03-01

The {beta}-decay half-lives of short-lived nuclei produced by 14 MeV neutron bombardments were measured with Ge detectors, a High-rate spectroscopy amplifier (EG and G ORTEC model 973) and a Spectrum multi-scaler (Laboratory equipment corporation SMS-48) in the multi-scaling mode. The adequate corrections for pile-up and dead-time losses were made by applying source and pulser methods. The half-lives of {sup 53}V, {sup 53g}Fe, {sup 89m}Y and {sup 162}Tb were determined with uncertainties of 0.13-0.65%. It has been shown that previous values shorter than 10 min were systematically longer than the present ones. (author)

Elimination of waste actinides by recycling them to nuclear reactors

International Nuclear Information System (INIS)

McKay, H.A.C.

1981-01-01

After a few centuries of radioactive decay the long-lived actinides, the elements of atomic numbers 89-103, may constitute the main potential radiological health hazard in nuclear wastes. This is because all but a very few fission products (principally technetium-99 and iodine-129) have by then decayed to insignificant levels, leaving the actinides as the principal hazardous species remaining. It is therefore at first sight an attractive idea to recycle the actinides in nuclear reactors, so as to eliminate them by nuclear fission. There are good reasons for examining the idea in detail, and studies have been carried out in a number of countries. These have culminated recently in international conferences at the European Joint Research Centre at Ispra in Italy and at Austin, Texas in the USA as well as in the issue of an IAEA Technical Report entitled An Evaluation of Actinide Partitioning and Transmutation, a product of a four-year IAEA Co-ordinated Research Programme, on which the present article is based. The term partitioning refers to the separation of the actinides from nuclear fuel cycle wastes, a necessary preliminary step to their introduction into reactors for transmutation by nuclear fission. The complete scheme will be referred to as P-T, i.e. partitioning-transmutation

Decay properties of short-lived mass-separated fission products

International Nuclear Information System (INIS)

Lund, E.

1977-01-01

The present work describes determinations of total β-decay energies and studies of delayed neutron emission including the identification and half-life determinations of delayed neutron precursors and the measurement of neutron spectra. It also includes a short review of the OSIRIS on-line isotope separator facility. (Auth.)

Ashing vs. electric generation in accelerator driven system

International Nuclear Information System (INIS)

Solanilla, Roberto B.

1999-01-01

Accelerator Driven Systems have been conceived as an alternative for the processing of the radioactive wastes contained in spent fuel elements from nuclear power plants. These systems are formed by the coupling of a nuclear reactor - preferably a subcritical reactor - with a particle accelerator providing particles with energy in the order of the GeV. The long-lived fission products and actinides of the spent fuels are transformed by nuclear reactions in stable isotopes or in short-lived radioisotopes. The basic parameters for the electric energy production of the different systems are analysed. (author)

Determination of difficult to measure actinides in radioactive liquid waste

International Nuclear Information System (INIS)

Drabova, V.; Galanda, D.; Dulanska, S.; Remenec, B.; Kuruc, J.

2014-01-01

In decommissioning of a nuclear facilities and radioactive waste treatment the activity of various radionuclides need to be measured for the waste characterization. Radiochemical separation of 241 Am, 237 Np and isotopes of plutonium was tested on model solution of evaporator concentrate sample for isolation of each of them for alpha-spectrometry analysis. This paper describes use of the molecular recognition technology product AnaLig(R)Pu-01 gel from IBC Advanced technologies, Inc. to effectively and selectively pre-concentrate, separate and recover difficult-to-measure actinides from model solution of evaporator concentrate samples which belong to the most difficult matrices to analyse. The method is suitable for analysing highly contaminated samples of radioactive waste in a relatively short time. For counting the alpha activity of 241 Am, 239,240 Pu, 238 Pu and 237 Np ORTEC 576A alpha-spectrometer equipped with ULTRA TM ion implanted silicon detectors (600 mm 2 active area) was used. The spectra were processed by using the Alpha-vision TM 32-bit emulation software from the EG and G ORTEC company. (authors)

Subsurface interactions of actinide species and microorganisms : implications for the bioremediation of actinide-organic mixtures

International Nuclear Information System (INIS)

Banaszak, J.E.; Reed, D.T.; Rittmann, B.E.

1999-01-01

By reviewing how microorganisms interact with actinides in subsurface environments, we assess how bioremediation controls the fate of actinides. Actinides often are co-contaminants with strong organic chelators, chlorinated solvents, and fuel hydrocarbons. Bioremediation can immobilize the actinides, biodegrade the co-contaminants, or both. Actinides at the IV oxidation state are the least soluble, and microorganisms accelerate precipitation by altering the actinide's oxidation state or its speciation. We describe how microorganisms directly oxidize or reduce actinides and how microbiological reactions that biodegrade strong organic chelators, alter the pH, and consume or produce precipitating anions strongly affect actinide speciation and, therefore, mobility. We explain why inhibition caused by chemical or radiolytic toxicities uniquely affects microbial reactions. Due to the complex interactions of the microbiological and chemical phenomena, mathematical modeling is an essential tool for research on and application of bioremediation involving co-contamination with actinides. We describe the development of mathematical models that link microbiological and geochemical reactions. Throughout, we identify the key research needs

Subsurface interactions of actinide species and microorganisms : implications for the bioremediation of actinide-organic mixtures.

Energy Technology Data Exchange (ETDEWEB)

Banaszak, J.E.; Reed, D.T.; Rittmann, B.E.

1999-02-12

By reviewing how microorganisms interact with actinides in subsurface environments, we assess how bioremediation controls the fate of actinides. Actinides often are co-contaminants with strong organic chelators, chlorinated solvents, and fuel hydrocarbons. Bioremediation can immobilize the actinides, biodegrade the co-contaminants, or both. Actinides at the IV oxidation state are the least soluble, and microorganisms accelerate precipitation by altering the actinide's oxidation state or its speciation. We describe how microorganisms directly oxidize or reduce actinides and how microbiological reactions that biodegrade strong organic chelators, alter the pH, and consume or produce precipitating anions strongly affect actinide speciation and, therefore, mobility. We explain why inhibition caused by chemical or radiolytic toxicities uniquely affects microbial reactions. Due to the complex interactions of the microbiological and chemical phenomena, mathematical modeling is an essential tool for research on and application of bioremediation involving co-contamination with actinides. We describe the development of mathematical models that link microbiological and geochemical reactions. Throughout, we identify the key research needs.

Development of fast-release solid catchers for rare isotopes

Science.gov (United States)

Nolen, Jerry; Greene, John; Elam, Jeffrey; Mane, Anil; Sampathkumaran, Uma; Winter, Raymond; Hess, David; Mushfiq, Mohammad; Stracener, Daniel; Wiendenhoever, Ingo

2015-04-01

Porous solid catchers of rare isotopes are being developed for use at high power heavy ion accelerator facilities such as RIKEN, FRIB, and RISP. Compact solid catchers are complementary to helium gas catchers for parasitic harvesting of rare isotopes in the in-flight separators. They are useful for short lived isotopes for basic nuclear physics research and longer-lived isotopes for off-line applications. Solid catchers can operate effectively with high intensity secondary beams, e.g. >> 1E10 atoms/s with release times as short as 10-100 milliseconds. A new method using a very sensitive and efficient RGA has been commissioned off-line at Argonne and is currently being shipped to Florida State University for in-beam measurements of the release curves using stable beams. The same porous solid catcher technology is also being evaluated for use in targets for the production of medical isotopes such as 211-At. Research supported by the U.S. DOE Office of Nuclear Physics under the SBIR Program and Contract # DE-AC02-06CH11357 and a University of Chicago Comprehensive Cancer Center/ANL Pilot Project.

Oxygen isotopic and geochemical evidence for a short-lived, high-temperature hydrothermal event in the Chegem caldera, Caucasus Mountains, Russia

Science.gov (United States)

Gazis, C.; Taylor, H.P.; Hon, K.; Tsvetkov, A.

1996-01-01

Within the 2.8 Ma Chegem ash-flow caldera (11 ?? 15 km), a single cooling unit of rhyolitic to dacitic welded tuff more than 2 km thick is exposed in deep valleys incised during recent rapid uplift of the Caucasus Mountains. The intracaldera tuff is mineralogically fresh and unaltered, and is overlain by andesite lavas and cut by a resurgent granodiorite intrusion. Major- and trace-element compositions for a 1405-m stratigraphic section of intracaldera tuff display trends of upwardly increasing Na2O, CaO, Al2O3, total Fe, MgO, TiO2, Sr and Zr and decreasing SiO2, K2O and Rb. This mafic-upward zoning (from 76.1 to 69.9% SiO2) reflects an inverted view of the upper part of the source magma chamber. Oxygen isotope studies of 35 samples from this 1405-m section define a striking profile with "normal" igneous ??18O values (+7.0 to +8.5) in the lower 600 m of tuff, much lower ??18O values (-4.0 to +4.3) in a 700-m zone above that and a shift to high ??18O values (+4.4 to -10.9) in the upper 100 m of caldera-fill exposure. Data from two other partial stratigraphic sections indicate that these oxygen isotope systematics are probably a caldera-wide phenomenon. Quartz and feldspar phenocrysts everywhere have "normal" igneous ??18O values of about +8.5 and +7.5, respectively, whereas groundmass and glass ??18O values range from -7.7 to +12.3. Consequently, the ??18O values of coexisting feldspar, groundmass and glass form a steep array in a plot of ??feldspar vs. ??groundmass/glass. Such pronounced disequilibrium between coexisting feldspar and groundmass or glass has never before been observed on this scale. It requires a hydrothermal event involving large amounts of low-18O H2O at sufficiently high temperatures and short enough time (tens of years or less) that glass exchanges thoroughly but feldspar does not. The most likely process responsible for the O depletions at Chegem is a very high temperature (500-600??C), short-lived, vigorous meteoric-hydrothermal event that was

Synthesis of radiopharmaceuticals containing short-lived radionuclides: Progress report, March 1, 1987-February 28, 1988

International Nuclear Information System (INIS)

Kabalka, G.W.

1987-09-01

The objective is the creation of new methods for introducing short-lived isotopes into agents for use in diagnostic nuclear medicine. Focus is on the design of new molecular architecture as opposed to the application of known reactions to the synthesis of specific radiopharmaceuticals. The new technology is utilized in nuclear medicine research at the University of Tennessee Medical Imaging Center and in collaboration with colleagues at other DOE facilities. The program provides training for students in the scientific aspects of nuclear medicine. The academic nature of the program facilitates collaborative interactions with other DOE nuclear medicine programs and helps to insure the continued availability of skilled scientists dedicated to the advancement of nuclear medicine. 70 refs., 9 figs

Radiotoxicity of Actinides During Transmutation in Final Stage of Atomic Power

International Nuclear Information System (INIS)

Gerasimov, Aleksander S.; Bergelson, Boris R.; Myrtsymova, Lidia A.; Tikhomirov, Georgy V.

2002-01-01

Characteristics of a transmutation mode in final stage of atomic power are analyzed. In this stage, transmutation of actinides accumulated in transmutation reactors is performed without feed by actinides from other reactors. The radiotoxicity during first 20 years of transmutation is caused mainly by 244 Cm. During following period of time, 252 Cf is main nuclide. Contribution of 246 Cm and 250 Cf is 5-7 times less than that of 252 Cf. During 50 years of a transmutation, the total radiotoxicity falls by 50 times. Long-lived radiotoxicity decreases slowly. During the period between T=50 years and T=100 years, long-lived radiotoxicity falls by 3.7 times. For each following 50 years after this period, long-lived radiotoxicity falls by 3.2 times. These results corresponding to neutron flux density 10 14 neutr/(cm 2 s) in transmutation reactor demonstrate that the final stage of a transmutation should be performed with use of high flux transmutation facilities which provide shorter time of transmutation. (authors)

Isotope specific resolution recovery image reconstruction in high resolution PET imaging

NARCIS (Netherlands)

Kotasidis, Fotis A.; Angelis, Georgios I.; Anton-Rodriguez, Jose; Matthews, Julian C.; Reader, Andrew J.; Zaidi, Habib

Purpose: Measuring and incorporating a scanner-specific point spread function (PSF) within image reconstruction has been shown to improve spatial resolution in PET. However, due to the short half-life of clinically used isotopes, other long-lived isotopes not used in clinical practice are used to

Isotopic Evidence for Multi-stage Cosmic-ray Exposure Histories of Lunar Meteorites: Long Residence on the Moon and Short Transition to the Earth

International Nuclear Information System (INIS)

Hidaka, Hiroshi; Sakuma, Keisuke; Nishiizumi, Kunihiko; Yoneda, Shigekazu

2017-01-01

It is known that most lunar meteorites have complicated cosmic-ray exposure experiences on the Moon and in space. In this study, cosmic-ray irradiation histories of six lunar meteorites, Dhofar 489, Northwest Africa 032 (NWA 032), NWA 479, NWA 482, NWA 2995, and NWA 5000, were characterized from neutron-captured isotopic shifts of Sm and Gd, and from the abundances of long-lived cosmogenic radionuclides like 10 Be, 26 Al, 36 Cl, and 41 Ca. Sm and Gd isotopic data of all of six meteorites show significant isotopic shifts of 149 Sm– 150 Sm and 157 Gd– 158 Gd caused by accumulation of neutron capture reactions due to cosmic-ray irradiation, corresponding to the neutron fluences of (1.3–9.6) × 10 16 n cm −2 . In particular, very large Sm and Gd isotopic shifts of NWA 482 are over those of a lunar regolith 70002, having the largest isotopic shifts among the Apollo regolith samples, corresponding to cosmic-ray exposure duration over 800 million years in the lunar surface (2 π irradiation). Meanwhile, the concentrations of cosmogenic radionuclides for individual six meteorites show the short irradiation time less than one million years as their bodies in space (4 π irradiation). Our data also support the results of previous studies, revealing that most of lunar meteorites have long exposure ages at shallow depths on the Moon and short transit times from the Moon to the Earth.

Complexation of transuranic elements: a look at factors which may enhance their biological availability

International Nuclear Information System (INIS)

Bulman, R.A.

1983-01-01

Nuclear fuel cycles produce long-lived α-emitting isotopes of the actinides. Many of these are isotopes of man-made elements for which there are no data on their long-term environmental behaviour. Their radio-toxic properties are sufficient to warrant concern about their behaviour in the environment. It is possible from the migration of some of the naturally occurring actinides to make some predictions as to the behaviour of the man-made actinides in the environment. Identified are complexing agents which may facilitate enhanced transport of actinides from soil into plants and also across the mammalian gut wall. (author)

Minor Actinides Recycling in PWRs

International Nuclear Information System (INIS)

Delpech, M.; Golfier, H.; Vasile, A.; Varaine, F.; Boucher, L.; Greneche, D.

2006-01-01

Recycling of minor actinides in current and near future PWR is considered as one of the options of the general waste management strategy. This paper presents the analysis of this option both from the core physics and fuel cycle point of view. A first indicator of the efficiency of different neutron spectra for transmutation purposes is the capture to fission cross sections ratio which is less favourable by a factor between 5 to 10 in PWRs compared to fast reactors. Another indicator presented is the production of high ranking isotopes like Curium, Berkelium or Californium in the thermal or epithermal spectrum conditions of PWR cores by successive neutron captures. The impact of the accumulation of this elements on the fabrication process of such PWR fuels strongly penalizes this option. The main constraint on minor actinides loadings in PWR (or fast reactors) fuels are related to their direct impact (or the impact of their transmutation products) on the reactivity coefficients, the reactivity control means and the core kinetics parameters. The main fuel cycle physical parameters like the neutron source, the alpha decay power, the gamma and neutrons dose rate and the criticality aspects are also affected. Recent neutronic calculations based on a reference core of the Evolutionary Pressurized Reactor (EPR), indicates typical maximum values of 1 % loadings. Different fuel design options for minor actinides transmutation purposes in PWRs are presented: UOX and MOX, homogeneous and heterogeneous assemblies. In this later case, Americium loading is concentrated in specific pins of a standard UOX assembly. Recycling of Neptunium in UOX and MOX fuels was also studied to improve the proliferation resistance of the fuel. The impact on the core physics and penalties on Uranium enrichment were underlined in this case. (authors)

From alchemy to super-actinides. The preparation, physical-chemical properties and the limits of the Periodic Table

International Nuclear Information System (INIS)

Kuruc, J.

2016-01-01

In this review a brief history of the discovery of the periodic law, discoveries of elements from the epoch of alchemy to the synthesis of actinides and transactinides is described. The preparation of transactinides (elements with Z ≥ 104 to Z = 118) is discussed, using already proposed names of the elements with Z = 113, 115, 117 and 118: nihonium, moscovium, tennessine and oganesson. The Periodic Tables are presented in short form, the long 18-column and 32-column form. The periodic table containing elements of 8"t"h and 9"t"h periods and its possible range is discussed. By extrapolation of decay half-time of the heaviest isotopes of elements from thorium up to oganesson decay half-time of unbihexium (Z = 126) was predicted about 378 seconds. (author

Characterization of actinide physics specimens for the US/UK joint experiment in the Dounreay Prototype Fast Reactor

International Nuclear Information System (INIS)

Walker, R.L.; Botts, J.L.; Cooper, J.H.; Adair, H.L.; Bigelow, J.E.; Raman, S.

1983-10-01

The United States and the United Kingdom are engaged in a joint research program in which samples of the higher actinides are irradiated in the Dounreay Prototype Fast Reactor in Scotland. The purpose of the porogram is (1) to study the materials behavior of selected higher actinide fuels and (2) to determine the integral cross sections of a wide variety of the higher actinide isotopes. Samples of the actinides are incorporated in fuel pins inserted in the core. For the fuel study, the actinides selected are 241 Am and 244 Cm in the form of Am 2 O 3 , Cm 2 O 3 , and Am 6 Cm(RE) 7 O 21 , where (RE) represents a mixture of lanthanides. For the cross-section determinations, the samples are milligram quantities of actinide oxides of 248 Cm, 246 Cm, 244 Cm, 243 Cm, 243 Am, 241 Am, 244 Pu, 242 Pu, 241 Pu, 240 Pu, 239 Pu, 238 Pu, 237 Np, 238 U, 236 U, 235 U, 234 U, 233 U, 232 Th, 230 Th, and 231 Pa encapsulated in vanadium. Coincident with the irradiations, neutron flux and energy spectral measurements are made with vanadium-encapsulated dosimeter materials located within the same fuel pins

Subsurface interactions of actinide species and microorganisms. Implications for the bioremediation of actinide-organic mixtures

International Nuclear Information System (INIS)

Banaszak, J.E.; Rittmann, B.E.; Reed, D.T.

1999-01-01

By reviewing how microorganisms interact with actinides in subsurface environments, the way how bioremediation controls the fate of actinides is assessed. Actinides often are co-contaminants with strong organic chelators, chlorinated solvents, and fuel hydrocarbons. Bioremediation can immobilize the actinides, biodegrade the co-contaminants, or both. Actinides at the IV oxidation state are the least soluble, and microorganisms accelerate precipitation by altering the actinide's oxidation state or its speciation. The way how microorganisms directly oxidize or reduce actinides and how microbiological reactions that biodegrade strong organic chelators, alter the pH, and consume or produce precipitating anions strongly affect actinide speciation and, therefore, mobility is described. Why inhibition caused by chemical or radiolytic toxicities uniquely affects microbial reactions is explained. Due to the complex interactions of the microbiological and chemical phenomena, mathematical modeling is an essential tool for research on and application of bioremediation involving co-contamination with actinides. Development of mathematical models that link microbiological and geochemical reactions is described. Throughout, the key research needs are identified. (author)

1982 Annual Status Report Plutonium Fuels and Actinide Programme

International Nuclear Information System (INIS)

Lindner, R.

1983-01-01

The programme of the Transuranium Institute has long included work on advanced fuels for fast breeder reactors. Study of the swelling of carbide and nitride fuels is now nearing completion, the retention of fission gases in bubbles of different sizes in the fuel having been quantified as function of burn-up and temperature. An important step forward has been achieved in the studies of the Equation of State of Nuclear Fuels up to 5000 K. Formation of some of the less abundant isotopes in PWR fuel has been determined experimentally. Aerosol formation during the fabrication of plutonium containing fuels, part of the activity Safe Handling of Plutonium Fuel has been studied. Head-End Processing of carbide fuels has continued experiments with high burn up mixed carbides. In the field of actinide research the preparation and characterisation of pure specimens is carried out. Effect of actinides on the properties of waste glasses is investigated

Project research on nuclear physical and chemical characteristics of actinide nuclides

International Nuclear Information System (INIS)

Yamana, Hajimu; Nakagome, Yoshihiro; Shibata, Seiichi; Fujii, Toshiyuki; Uehara, Akihiro; Shirai, Osamu; Moriyama, Hirotake; Nagai, Takayuki; Yamanaka, Shinsuke; Shinohara, Atsushi; Kurata, Masaki; Myochin, Munetaka; Nakamura, Shoji; Matsuura, Haruaki

2008-01-01

The chemical and nuclear physical characteristics of actinide elements have been investigated using the experimental methods and instruments of this laboratory. This laboratory has a facility in which the transuranium elements (TRU) and the long-lived fission products (LLFP) can be dealt with. The utility of this facility has been expected. The investigation on the actinide elements and its fission products have been carried out as a project research from both view points of science and technology. The research reports during three years (2005-07) are described here. (M.H.)

Prospects for baryon instability search with long-lived isotopes

Energy Technology Data Exchange (ETDEWEB)

Efremenko, Yu. [Oak Ridge National Lab., TN (United States)][Tennessee Univ., Knoxville, TN (United States); Bugg, W.; Cohn, H. [Tennessee Univ., Knoxville, TN (United States); Kamyshkov, Yu. [Oak Ridge National Lab., TN (United States)][Tennessee Univ., Knoxville, TN (United States); Parker, G.; Plasil, F. [Oak Ridge National Lab., TN (United States)

1996-12-31

In this paper we consider the possibility of observation of baryon instability processes occurring inside nuclei by searching for the remnants of such processes that could have been accumulated in nature as mm long-lived isotopes. As an example, we discuss here the possible detection of traces of {sup 97}Tc, {sup 98}Tc, and {sup 99}Tc in deep-mined nonradioactive tin ores.

Actinide colloid generation in groundwater

International Nuclear Information System (INIS)

Kim, J.I.

1990-05-01

The progress made in the investigation of actinide colloid generation in groundwaters is summarized and discussed with particular examples relevant to an understanding of the migration behaviour of actinides in natural aquifer systems. The first part deals with the characterization of colloids: groundwater colloids, actinide real-colloids and actinide pseudocolloids. The second part concentrates on the generation processes and migration behaviour of actinide pseudocolloids, which are discussed with some notable experimental examples. Importance is stressed more on the chemical aspects of the actinide colloid generation in groundwater. This work is a contribution to the CEC project MIRAGE II, particularly, to research area: complexation and colloids. (orig.)

Application of accelerator-produced short-lived radionuclides in industry

International Nuclear Information System (INIS)

Kupsch, H.

1986-01-01

Several problems such as corrosion, catalysis, wear, process optimization and diagnosis, damage analysis, arising in idustry can be solved using short-lived radioisotopes. Some examples of technological target designs which have been developed are demonstrated for the radionuclide production based on p,n; d,α; α,n; α,2n; α,p; γ,n; γ,p nuclear reactions. Applications of short-lived radionuclides in plants and processes of electrodeposition and gas concrete production are described. (author)

The cross section sensitivity of the minor actinides on a lead-bismuth cooled accelerator-driven burner system

International Nuclear Information System (INIS)

Gil, Choong-Sup; Kim, Jung-Do; Chang, Jonghwa

2002-01-01

In order to validate the detailed sensitivity of each minor actinide datum in ENDF/B-VI Release 6, JEF-2.2 and JENDL-3.2 on an accelerator-driven minor actinide burner benchmark system, a lead-bismuth cooled sub-critical system was analyzed. The impacts on the system by the ten minor actinides were compared. The k eff values and reaction rates were calculated by exchanging the data sets of each minor actinide from ENDF/B-VI.6 to JEF-2.2 or JENDL-3.2. At the equilibrium core, the k eff differences from ENDF/B-VI.6 by the ten minor actinides can cause more than 5,500 pcm for JEF-2.2 and 3,500 pcm for JENDL-3.2. The fission reaction rates of 242m Am and 243 Cm with ENDF/B-VI.6 show differences of more than 15% from those with JEF-2.2 and JENDL-3.2. 241 Am, 243 Am and 245 Cm in JEF-2.2 and americium isotope data and 245 Cm in JENDL-3.2 are sensitive to the fission spectrum. (author)

Potential radiation dose from eating fish exposed to actinide contamination

International Nuclear Information System (INIS)

Emery, R.M.; Klopfer, D.C.; Baker, D.A.; Soldat, J.K.

1980-01-01

The purpose of this work is to establish a maximum potential for transporting actinides to man via fish consumption. The study took place in U-Pond, a nuclear waste pond on the Hanford Site. It has concentrations of 238 U, 238 Pu, /sup 239,240/Pu and 241 Am that are approximately three orders of magnitude greater than background levels. Fish living in the pond contain higher actinide concentrations than those observed in fish from any other location. Experiments were performed in U-pond to determine maximum quantities of actinides that could accumulate in fillets and whole bodies of two centrarchid fish species. Doses to hypothetical consumers were then estimated by assuming that actinide behavior in their bodies was similar to that defined for Standard Man by the International Commission on Radiological Protection. Results indicate that highest concentrations occurring in bluegill or bass muscle after more than a year's exposure to the pond would not be sufficient to produce a significant radiation dose to a human consumer, even if he ate 0.5 kg (∼1 lb) of these fillets every day for 70 years. Natural predators (heron or coyote), having lifetime diets of whole fish from U-Pond, would receive less radiation dose from the ingested actinides than from natural background sources. 34 refs., 5 figs., 4 tabs

A new look at actinide recycle

International Nuclear Information System (INIS)

Burch, W.D.; Croff, A.G.; Rawlins, J.A.; Schulz, W.W.

1991-01-01

This paper will address the justification for reexamination of the value of recovering the minor actinides and certain fission products from spent light-water reactor fuels and describe some of the technical progress that has been made since the major studies of a decade ago. During this time, the US Environmental Protection Agency (EPA) and the Nuclear Regulatory Commission have begun establishing detailed criteria and regulations for geologic repositories. An examination of the hazards of waste disposal relative to the EPA release standards reveals that removal of 99.9% of the actinides (Pu, Am, and Np) reduces these hazards quite close to the EPA standards after 300 years' decay of the strontium and cesium. It may be also useful to remove and separately manage and dispose of certain of the long-lived fission products, such as 99 Tc and 129 I. Much additional work is required to fully assess the appropriate target recoveries as the hazards and risks are more closely examined and as the standards are reworked and refined. The two decades before the projected start of the US repository may present a window of opportunity to introduce several better management practices that act to simplify the repository safety issues. From a technical standpoint, significant progress has been made on recovery of the actinides from aqueous wastes though use of the TRUEX process. Additional work is required to demonstrate the application of the process to spent LWR fuels, but it appears straightforward. In addition, work at the Argonne National Laboratory on the liquid-metal reactor metal fuel cycle shows the relative simplicity of recycle of the actinides in that fast reactor cycle. Much work remains to fully demonstrate that actinides from all secondary waste streams can be removed to the target levels from both the aqueous reprocessing of LWR fuel and the pyro processes for the metal-fueled fast reactor. 9 refs., 2 figs

Potential radiation dose from eating fish exposed to actinide contamination

International Nuclear Information System (INIS)

Emery, R.M.; Klopfer, D.C.; Baker, D.A.; Soldat, J.K.

1981-01-01

The purpose of this work is to establish a maximum potential for transporting actinides to man via fish consumption. The study took place in U-pond, a nuclear waste pond on the Hanford Site. It has concentrations of 238 U, 238 Pu, sup(239,240)Pu and 241 Am that are approx. 3 orders of magnitude greater than background levels. Fish living in the pond contain higher actinide concentrations than those observed in fish from any other location. Experiments were performed in U-Pond to determine maximum quantities of actinides that could accumulate in fillets and whole bodies of two centrarchid fish species. Doses to hypothetical consumers were then estimated. Results indicate that highest concentrations occurring in bluegill or bass muscle after more than a year's exposure to the pond would not be sufficient to produce a significant radiation dose to a human consumer, even if he ate 0.5 kg (of the order of 1 lb) of these fillets every day for 70 yr. Natural predators (heron or coyote), having lifetime diets of whole fish from U-Pond, would receive less radiation dose from the ingested actinides than from natural background sources. (author)

Wide-band digital equipment for study of neutron reactions producing short-living isotopes

International Nuclear Information System (INIS)

Bonyushkin, E.K.; Boyarintsev, V.A.; Goryushkin, S.I.; Drozdov, Yu.M.; Orlov, R.A.

1976-01-01

Digital equipment designed for recording automatically curves of decay for radioactive isotopes with a half-life period of about 10 Ms is described. Detection of a signal produced by isotope-isomer radioactive radiation is performed in the integral mode. A block-diagram of the measuring channel corresponding to the current mode of recording is presented. The accuracy characteristics of such a measuring channel are determined primarily by parameters of an analog-digital converter and they do not depend upon the length of the signal cable. Principles of operation for digital equipment are based on logarithmic conversion of the d.c. voltage into a number of pulses by the oscillating contour, i.e. a number of pulses in the envelope is proportional to the logarithm of the strobbed voltage. The amplitude range of recording is higher than 10 3 . Total instrumental errors of recording are about 5 per cent

Criticality and thermal analyses of separated actinides

International Nuclear Information System (INIS)

Bakker, E.

2004-01-01

Curium and americium pose special problems in the chemical preparation of spent fuel for transmutation. Once separated from the other actinides, the isotopes can lead to nuclear fission with the subsequent release of a large amount of radiation. A neutron criticality code was used to determine k eff for varying quantities of Cm 2 O 3 and Am 2 O 3 held within spherical or cylindrical containers. These geometries were investigated both in air and in water. Recommendations are made on the maximum amount of Cm 2 O 3 and Am 2 O 3 that can be safely stored or handled before encountering criticality. Several isotopes of curium and americium also generate a significant amount of heat by radioactive decay. If kilogram quantities are stored in a container, for example, the material may heat to an equilibrium temperature that exceeds its melting temperature. The heat generation of curium and americium present even more restriction on the mass of that can safely be contained in one location. (author)

A reexamination of the incentives for actinide burning

International Nuclear Information System (INIS)

Croff, A.G.; Forsberg, C.W.; Ludwig, S.B.

1990-01-01

The incentives for actinide burning (AB), also known as partitioning and transmutation, were extensively evaluated over a decade ago by US and foreign investigators. The conclusion was that the cost and short-term risk increases resulting from AB substantially outweighed the long-term reduction in repository risk. However, during the intervening years, many factors relevant to this evaluation have changed, such as (a) expectations concerning the ease with which a repository could be sited and licensed, (b) issuance by regulators of a repository licensing standard and supporting criteria, (c) the scenario to which AB is compared, and (d) new technologies for fuel and waste processing. This paper reexamines the incentives for undertaking actinide burning the content of these new factors. 10 refs., 3 figs

Chemical interaction of tetravalent actinides simulators and the engineering barrier

International Nuclear Information System (INIS)

Chain, Pablo; Alba, Maria D.; Castro, Miguel A.; Pavon, Esperanza; Mar Orta, M.

2010-01-01

Document available in extended abstract form only. The Deep Geological Repository (DGR) is the most internationally accepted option for the storage of high radioactive wastes. This confinement is based on the Multi-barrier Concept where the engineered barrier is a crucial safety wise. Nowadays, bentonite is accepted as the best argillaceous material in the engineered barrier of DGR. Additionally to its well-known physical role, a chemical interaction between lutetium, as actinide simulator, and the smectite has been demonstrated. The existence of a reaction mechanism, which was not previously described, based on the chemical interaction between the lanthanide cations and the orthosilicate anions of the lamellar structure has been identified. This finding has aroused the interest of the scientific community because lanthanides are used as simulators of high activity radionuclide (HAR) in agreement with the guidelines established in the bibliography. It has been observed that in conditions of moderate temperature and pressure a chemical interaction exists between smectites and rare earth elements (RE) and phases of insoluble di-silicate, RE 2 Si 2 O 7 , which would immobilize RE, are generated. It is remarkable that the reaction extends to all the set of the smectites, although they do not display the same reactivity, the saponite being the most reactive. The main isotopes present in the HLW belong to the actinide elements Np, Pu, Am and Cm, in addition to uranium generated by neutron capture during the fuel combustion process. The study of the mobilization of actinide (IV) thorough the bentonite barrier is limited because of their radioactivity. However, U(IV), Np(IV), Pu(IV) and Th(IV) can be simulated by the stable isotopes of the Zr(IV) and Hf(IV), because they exhibit ionic radius and physicochemical properties very similar to those of the actinide elements. It is the main objective of this research to investigate the chemical interaction of Zr(IV) as actinide

New Developments in Actinides Burning with Symbiotic LWR-HTR-GCFR Fuel Cycles

International Nuclear Information System (INIS)

Bomboni, Eleonora

2008-01-01

The long-term radiotoxicity of the final waste is currently the main drawback of nuclear power production. Particularly, isotopes of Neptunium and Plutonium along with some long-lived fission products are dangerous for more than 100000 years. 96% of spent Light Water Reactor (LWR) fuel consists of actinides, hence it is able to produce a lot of energy by fission if recycled. Goals of Generation IV Initiative are reduction of long-term radiotoxicity of waste to be stored in geological repositories, a better exploitation of nuclear fuel resources and proliferation resistance. Actually, all these issues are intrinsically connected with each other. It is quite clear that these goals can be achieved only by combining different concepts of Gen. IV nuclear cores in a 'symbiotic' way. Light-Water Reactor - (Very) High Temperature Reactor ((V)HTR) - Fast Reactor (FR) symbiotic cycles have good capabilities from the viewpoints mentioned above. Particularly, HTR fuelled by Plutonium oxide is able to reach an ultra-high burn-up and to burn Neptunium and Plutonium effectively. In contrast, not negligible amounts of Americium and Curium build up in this core, although the total mass of Heavy Metals (HM) is reduced. Americium and Curium are characterised by an high radiological hazard as well. Nevertheless, at least Plutonium from HTR (rich in non-fissile nuclides) and, if appropriate, Americium can be used as fuel for Fast Reactors. If necessary, dedicated assemblies for Minor Actinides (MA) burning can be inserted in Fast Reactors cores. This presentation focuses on combining HTR and Gas Cooled Fast Reactor (GCFR) concepts, fuelled by spent LWR fuel and depleted uranium if need be, to obtain a net reduction of total mass and radiotoxicity of final waste. The intrinsic proliferation resistance of this cycle is highlighted as well. Additionally, some hints about possible Curium management strategies are supplied. Besides, a preliminary assessment of different chemical forms of

Research in actinide chemistry

International Nuclear Information System (INIS)

Choppin, G.R.

1993-01-01

This research studies the behavior of the actinide elements in aqueous solution. The high radioactivity of the transuranium actinides limits the concentrations which can be studied and, consequently, limits the experimental techniques. However, oxidation state analogs (trivalent lanthanides, tetravalent thorium, and hexavalent uranium) do not suffer from these limitations. Behavior of actinides in the environment are a major USDOE concern, whether in connection with long-term releases from a repository, releases from stored defense wastes or accidental releases in reprocessing, etc. Principal goal of our research was expand the thermodynamic data base on complexation of actinides by natural ligands (e.g., OH - , CO 3 2- , PO 4 3- , humates). The research undertakes fundamental studies of actinide complexes which can increase understanding of the environmental behavior of these elements

Recovery of actinides from actinide-aluminium alloys by chlorination: Part I

Energy Technology Data Exchange (ETDEWEB)

Cassayre, L., E-mail: cassayre@chimie.ups-tlse.fr [Laboratoire de Genie Chimique (LGC), Departement Procedes Electrochimiques, CNRS-UMR 5503, Universite de Toulouse III - Paul Sabatier, 31062 Toulouse (France); Soucek, P.; Mendes, E.; Malmbeck, R.; Nourry, C.; Eloirdi, R.; Glatz, J.-P. [European Commission, JRC, Institute for Transuranium Elements, Postfach 2340, 76125 Karlsruhe (Germany)

2011-07-01

Pyrochemical processes in molten LiCl-KCl are being developed in ITU for recovery of actinides from spent nuclear fuel. The fuel is anodically dissolved to the molten salt electrolyte and actinides are electrochemically reduced on solid aluminium cathodes forming solid actinide-aluminium alloys. A chlorination route is being investigated for recovery of actinides from the alloys. This route consists in three steps: Vacuum distillation for removal of the salt adhered on the electrode, chlorination of the actinide-aluminium alloys by chlorine gas and sublimation of the formed AlCl{sub 3}. A thermochemical study showed thermodynamic feasibility of all three steps. On the basis of the conditions identified by the calculations, experiments using pure UAl{sub 3} alloy were carried out to evaluate and optimise the chlorination step. The work was focused on determination of the optimal temperature and Cl{sub 2}/UAl{sub 3} molar ratio, providing complete chlorination of the alloy without formation of volatile UCl{sub 5} and UCl{sub 6}. The results showed high efficient chlorination at a temperature of 150 deg. C.

Recovery of actinides from actinide-aluminium alloys by chlorination: Part I

International Nuclear Information System (INIS)

Cassayre, L.; Soucek, P.; Mendes, E.; Malmbeck, R.; Nourry, C.; Eloirdi, R.; Glatz, J.-P.

2011-01-01

Pyrochemical processes in molten LiCl-KCl are being developed in ITU for recovery of actinides from spent nuclear fuel. The fuel is anodically dissolved to the molten salt electrolyte and actinides are electrochemically reduced on solid aluminium cathodes forming solid actinide-aluminium alloys. A chlorination route is being investigated for recovery of actinides from the alloys. This route consists in three steps: Vacuum distillation for removal of the salt adhered on the electrode, chlorination of the actinide-aluminium alloys by chlorine gas and sublimation of the formed AlCl 3 . A thermochemical study showed thermodynamic feasibility of all three steps. On the basis of the conditions identified by the calculations, experiments using pure UAl 3 alloy were carried out to evaluate and optimise the chlorination step. The work was focused on determination of the optimal temperature and Cl 2 /UAl 3 molar ratio, providing complete chlorination of the alloy without formation of volatile UCl 5 and UCl 6 . The results showed high efficient chlorination at a temperature of 150 deg. C.

Transmutation of nuclear waste. Status report RAS programme 1994: Recycling and transmutation of actinides and fission products

Energy Technology Data Exchange (ETDEWEB)

Cordfunke, E H.P.; Gruppelaar, H; Franken, W M.P.

1995-07-01

This report describes the status and progress of the Dutch RAS programme on `Recycling and Transmutation of Actinides and Fission Products` over the year 1994, which is the first year of the second 4-year programme. This programme is outlined and a short progress report is given over 1994, including a listing of 23 reports and publications over the year 1994. Highlights of 1994 were: The completion of long-lived fission-product transmutation studies, the initiation of small-scale demonstration experiments in the HFR on Tc and I, the issue of reports on the potential of the ALMR (Advanced Liquid Metal Reactor) for transmutation adn the participation and international cooperation on irradiation experiments with actinides in inert matrices. The remaining chapters contain more extended contributions on recent developments and selected topics, under the headings: Benefits and risks of partitioning and transmutation, Perspective of chemical partitioning, Inert matrices, Evolutionary options (MOX), Perspective of heavy water reactors, Perspective of fast burners, Perspective of accelerator-based systems, Thorium cycle, Fission-product transmutation, End scenarios, and Executive summary and recommendations. (orig.).

Transmutation of nuclear waste. Status report RAS programme 1994: Recycling and transmutation of actinides and fission products

International Nuclear Information System (INIS)

Cordfunke, E.H.P.; Gruppelaar, H.; Franken, W.M.P.

1995-07-01

This report describes the status and progress of the Dutch RAS programme on 'Recycling and Transmutation of Actinides and Fission Products' over the year 1994, which is the first year of the second 4-year programme. This programme is outlined and a short progress report is given over 1994, including a listing of 23 reports and publications over the year 1994. Highlights of 1994 were: The completion of long-lived fission-product transmutation studies, the initiation of small-scale demonstration experiments in the HFR on Tc and I, the issue of reports on the potential of the ALMR (Advanced Liquid Metal Reactor) for transmutation adn the participation and international cooperation on irradiation experiments with actinides in inert matrices. The remaining chapters contain more extended contributions on recent developments and selected topics, under the headings: Benefits and risks of partitioning and transmutation, Perspective of chemical partitioning, Inert matrices, Evolutionary options (MOX), Perspective of heavy water reactors, Perspective of fast burners, Perspective of accelerator-based systems, Thorium cycle, Fission-product transmutation, End scenarios, and Executive summary and recommendations. (orig.)

Monitoring of processes with gamma-rays of neutron capture and short-living radionuclides

International Nuclear Information System (INIS)

Aripov, G.A.; Kurbanov, B.I.; Allamuratova, G.

2004-01-01

Element content is a fundamental parameter of a substance, on which all its properties, and also character of physical, chemical, biological, technological and ecological processes depend. Therefore monitoring of element content (in the course of technological process - on line; in natural conditions - in site; or in living organisms - in vivo) becomes necessary for investigation of aforementioned processes. This problem can be successfully solved by using the methods of prompt gamma activation analysis (PGAA) and instrumental neutron activation analysis (INAA) on short-living radionuclides. These methods don't depend on type of substance (biological, geological, technological etc.), since the content is determined by gamma radiation of nuclei, and allows to meet such a serious requirement like the necessity of achieving minimal irradiation of the object and its minimal residual activity. In this work minimal determinable concentrations of various elements are estimated (based on experimental data) by the method of PGAA using radionuclide 252 Cf - source of neutrons with the yield of the oil of 10 8 neutron/sec on the experimental device with preliminary focusing of neutrons /1/, and also data of determination of elements by their isotopes with maximum time efficiency /2,3/ by the method of INAA. (author)

Isotopic Evidence for Multi-stage Cosmic-ray Exposure Histories of Lunar Meteorites: Long Residence on the Moon and Short Transition to the Earth

Energy Technology Data Exchange (ETDEWEB)

Hidaka, Hiroshi; Sakuma, Keisuke [Department of Earth and Planetary Sciences, Nagoya University Nagoya 464-8601 (Japan); Nishiizumi, Kunihiko [Space Sciences Laboratory, University of California, Berkeley, CA 94720-7450 (United States); Yoneda, Shigekazu, E-mail: hidaka@eps.nagoya-u.ac.jp [Department of Science and Engineering, National Museum of Nature and Science Tsukuba 305-0005 (Japan)

2017-06-01

It is known that most lunar meteorites have complicated cosmic-ray exposure experiences on the Moon and in space. In this study, cosmic-ray irradiation histories of six lunar meteorites, Dhofar 489, Northwest Africa 032 (NWA 032), NWA 479, NWA 482, NWA 2995, and NWA 5000, were characterized from neutron-captured isotopic shifts of Sm and Gd, and from the abundances of long-lived cosmogenic radionuclides like {sup 10}Be, {sup 26}Al, {sup 36}Cl, and {sup 41}Ca. Sm and Gd isotopic data of all of six meteorites show significant isotopic shifts of {sup 149}Sm–{sup 150}Sm and {sup 157}Gd–{sup 158}Gd caused by accumulation of neutron capture reactions due to cosmic-ray irradiation, corresponding to the neutron fluences of (1.3–9.6) × 10{sup 16} n cm{sup −2}. In particular, very large Sm and Gd isotopic shifts of NWA 482 are over those of a lunar regolith 70002, having the largest isotopic shifts among the Apollo regolith samples, corresponding to cosmic-ray exposure duration over 800 million years in the lunar surface (2 π irradiation). Meanwhile, the concentrations of cosmogenic radionuclides for individual six meteorites show the short irradiation time less than one million years as their bodies in space (4 π irradiation). Our data also support the results of previous studies, revealing that most of lunar meteorites have long exposure ages at shallow depths on the Moon and short transit times from the Moon to the Earth.

Advanced concepts for gamma-ray isotopic analysis and instrumentation

International Nuclear Information System (INIS)

Buckley, W.M.; Carlson, J.B.

1994-07-01

The Safeguards Technology Program at the Lawrence Livermore National Laboratory is developing actinide isotopic analysis technologies in response to needs that address issues of flexibility of analysis, robustness of analysis, ease-of-use, automation and portability. Recent developments such as the Intelligent Actinide Analysis System (IAAS), begin to address these issues. We are continuing to develop enhancements on this and other instruments that improve ease-of-use, automation and portability. Requests to analyze samples with unusual isotopics, contamination, or containers have made us aware of the need for more flexible and robust analysis. We have modified the MGA program to extend its plutonium isotopic analysis capability to samples with greater 241 Am content or U isotopics. We are looking at methods for dealing with tantalum or lead contamination and contamination with high-energy gamma emitters, such as 233 U. We are looking at ways to allow the program to use additional information about the sample to further extend the domain of analyzable samples. These unusual analyses will come from the domain of samples that need to be measured because of complex reconfiguration or environmental cleanup

Automated complex spectra processing of actinide α-radiation

International Nuclear Information System (INIS)

Anichenkov, S.V.; Popov, Yu.S.; Tselishchev, I.V.; Mishenev, V.B.; Timofeev, G.A.

1989-01-01

Earlier described algorithms of automated processing of complex α - spectra of actinides with the use of Ehlektronika D3-28 computer line, connected with ICA-070 multichannel amplitude pulse analyzer, were realized. The developed program enables to calculated peak intensity and the relative isotope content, to conduct energy calibration of spectra, to calculate peak center of gravity and energy resolution, to perform integral counting in particular part of the spectrum. Error of the method of automated processing depens on the degree of spectrum complication and lies within the limits of 1-12%. 8 refs.; 4 figs.; 2 tabs

Actinides

International Nuclear Information System (INIS)

Martinot, L.; Fuger, J.

1985-01-01

The oxidation behavior of the actinides is explained on the basis of their electronic structure. The actinide elements, actinium, thorium, protactinium, uranium, neptunium, plutonium, americium, curium, berkelium, californium, einsteinium, fermium, mendelevium, nobelium, and laurencium are included. For all except the last three elements, the points of discussion are oxidation states, Gibbs energies and potentials, and potential diagram for the element in acid solution; and thermodynamic properties of these same elements are tabulated. References are cited following discussion of each element with a total of 97 references being cited. 13 tables

Crystalline matrices for the immobilization of plutonium and actinides

Energy Technology Data Exchange (ETDEWEB)

Anderson, E.B.; Burakov, E.E.; Galkin, Ya.B.; Starchenko, V.A.; Vasiliev, V.G. [V.G. Khlopin Radium Institute, St. Petersburg (Russian Federation)

1996-05-01

The management of weapon plutonium, disengaged as a result of conversion, is considered together with the problem of the actinide fraction of long-lived high level radioactive wastes. It is proposed to use polymineral ceramics based on crystalline host-phases: zircon ZrSiO{sub 4} and zirconium dioxide ZrO{sub 2}, for various variants of the management of plutonium and actinides (including the purposes of long-term safe storage or final disposal from the human activity sphere). It is shown that plutonium and actinides are able to form with these phases on ZrSiO{sub 4} and ZrO{sub 2} was done on laboratory level by the hot pressing method, using the plasmochemical calcination technology. To incorporate simulators of plutonium into the structure of ZrSiO{sub 4} and ZrO{sub 2} in the course of synthesis, an original method developed by the authors as a result of studying the high-uranium zircon (Zr,U) SiO{sub 4} form Chernobyl {open_quotes}lavas{close_quotes} was used.

Response of actinides to flux changes in high-flux systems

International Nuclear Information System (INIS)

Sailor, W.C.

1993-01-01

When discussing the transmutation of actinides in accelerator-based transmutation of waste (ATW) systems, there has been some concern about the dynamics of the actinides under high transient fluxes. For a pure neptunium feed, it has been estimated that the 238 Np/ 237 Np ratio increase due to an increasing flux may lead to an unstable, positive reactivity growth. In this analysis, a perturbation method is used to calculate the response of the entire set of actinides in a general way that allows for more species than just neptunium. The time response of the system can be calculated; i.e., a plot of fuel composition and reactivity versus time after a change in flux can be made. The effects of fission products can also be included. The procedure is extremely accurate on short time scales (∼ 1000 s) for the flux levels we contemplate. Calculational results indicate that the reactivity insertions are always smaller than previously estimated

New data on some short-lived isotopes of ruthenium and rhodium; Nuevos datos sobre algunos isotopos de rutenio y rodio de vida corta

Energy Technology Data Exchange (ETDEWEB)

Baumgartner, F.; Plata Bedmar, A.

1961-07-01

Ru and Rd isotopes with mass numbers 107 and 108 and {sup 1}09Rh, has been obtained from fission products. {sup 1}07 Ru has also been prepared by the nuclear process {sup 1}10Pd (n,{alpha}) {sup 1}07 Ru. Beta and gamma energies of these nuclides have been studied spectropolarimetry and the gamma lines found for {sup 1}07 Ru and {sup 1}08Ru ( and daughter) have been very useful for the precise determination of their half-lives. {sup 1}09Rh has been identified through its daughter {sup 1}09Pd in the mixture of rhodium isotopes from fission products. Irradiation of natural palladium with fast neutrons has lead to an activity that may only be attributed to {sup 1}10rh. Neither its half life nor its decay energy have been possible to determine accurately. (Author) 1 refs.

Geochemical constraints on accumulation of actinide critical masses from stored nuclear waste in natural rock repositories. Technical report, April 1, 1978--August 31, 1978 (plus supplemental time to December 31, 1978)

International Nuclear Information System (INIS)

Brookins, D.G.

1978-01-01

Results of a literature search of abundant data on lanthanide and actinide individual and joint systematics are presented. Covered were several papers/reports about uranium solution chemistry, uranium deposits, a natural fission reactor, rare-earch deposits, manganese nodules, bedded and dome salt deposits, and miscellaneous items. This literature search is not complete but represents efforts of seven individuals attempting to gather data relevant to the objectives defined in this report. Many foreign articles, as well as many English language articles are absent. Approximately 800 articles were inspected; 69 are included in the References cited. The data search for actinides and lanthanides in natural rocks indicated that only limited segregation of the actinides U, Np, Pu, Am, and Cm from the lanthanides is possible should high-level waste be released from canisters stored in various geomedia. Supporting this were studies of Oklo and other uranium deposits, manganese nodules, monomineralic and concretion formation rates, and actinide and lathanide transport in brines. The fact that some waste canisters may, under certain conditions, contain several critical masses of one or more actinides is countered by the facts that (a) most actinides have very short half-lives and would decay before release from canisters, (b) released actinides and lanthanides, although dispersed, would be transported and deposited as a group, thus preventing point concentration of any actinides, and (c) 235 U has a much longer half-life than the other actinides, thus allowing greater time for possible reaccumulation and criticality; such a scenario would demand that 235 U be segregated effectively from other elements in the lanthanide-actinide groups.No mechanism to do this is consistent with the natural occurrences studied or the theoretical Eh-pH diagrams considered

Multi-actinide analysis with AMS for ultra-trace determination and small sample sizes: advantages and drawbacks

Energy Technology Data Exchange (ETDEWEB)

Quinto, Francesca; Lagos, Markus; Plaschke, Markus; Schaefer, Thorsten; Geckeis, Horst [Institute for Nuclear Waste Disposal, Karlsruhe Institute of Technology (Germany); Steier, Peter; Golser, Robin [VERA Laboratory, Faculty of Physics, University of Vienna (Austria)

2016-07-01

With the abundance sensitivities of AMS for U-236, Np-237 and Pu-239 relative to U-238 at levels lower than 1E-15, a simultaneous determination of several actinides without previous chemical separation from each other is possible. The actinides are extracted from the matrix elements via an iron hydroxide co-precipitation and the nuclides sequentially measured from the same sputter target. This simplified method allows for the use of non-isotopic tracers and consequently the determination of Np-237 and Am-243 for which isotopic tracers with the degree of purity required by ultra-trace mass-spectrometric analysis are not available. With detection limits of circa 1E+4 atoms in a sample, 1E+8 atoms are determined with circa 1 % relative uncertainty due to counting statistics. This allows for an unprecedented reduction of the sample size down to 100 ml of natural water. However, the use of non-isotopic tracers introduces a dominating uncertainty of up to 30 % related to the reproducibility of the results. The advantages and drawbacks of the novel method will be presented with the aid of recent results from the CFM Project at the Grimsel Test Site and from the investigation of global fallout in environmental samples.

Legal and regulatory issues regarding classification and disposal of wastes from actinide partitioning and transmutation

International Nuclear Information System (INIS)

Kocher, D.C.

1989-01-01

Partitioning and transmutation of actinide radioelements in spent nuclear fuel from civilian power reactors is potentially attractive because the resulting wastes might be acceptable for disposal using systems which are considerably less costly than a deep geologic repository. At present, there are no legal or regulatory prohibitions to seeking alternatives to a geologic repository for disposal of such wastes. However, additional laws and regulations would be needed, and the Nuclear Regulatory Commission has been reluctant to alter the current framework for radioactive waste management, in which geologic repositories or near-surface facilities are the only disposal options established in law and regulations unless a compelling need for alternatives with intermediate waste-isolation capabilities is demonstrated. There are also important technical considerations which are not encouraging with regard to the development of intermediate disposal systems for wastes from partitioning and transmutation of actinides in civilian spent fuel. First, the wastes may contain sufficient concentrations of fission products. Second, defense reprocessing wastes may contain sufficient concentrations of fission products and long-lived actinides. Thus, in developing the legal and regulatory framework for alternative disposal systems, there is a need to establish maximum concentrations of fission products and long-lived actinides that would be acceptable for intermediate disposal. 19 refs

Possibilities of production of neutron-rich Md isotopes in multi-nucleon transfer reactions

Energy Technology Data Exchange (ETDEWEB)

Mun, Myeong-Hwan; Lee, Young-Ouk [Korea Atomic Energy Research Institue, Daejeon (Korea, Republic of); Adamian, G.G.; Antonenko, N.V. [Joint Institute for Nuclear Research, Dubna (Russian Federation)

2016-12-15

The possibilities of production of yet unknown neutron-rich isotopes of Md are explored in several multi-nucleon transfer reactions with actinide targets and stable and radioactive beams. The projectile-target combinations and bombarding energies are suggested to produce new neutron-rich isotopes of Md in future experiments. (orig.)

Chemistry of tetravalent actinides phosphates. The thorium phosphate-diphosphate as immobilisation matrix of actinides

International Nuclear Information System (INIS)

Dacheux, N.

2002-01-01

The author presents in this document its scientific works from 1992 to 2001, in order to obtain the enabling to manage scientific and chemical researches at the university Paris Sud Orsay. The first part gives an abstract of the thesis on the characterizations, lixiviation and synthesis of uranium and thorium based phosphate matrix in the framework of the search for a ceramic material usable in the radioactive waste storage. The second part presents briefly the researches realized at the CEA, devoted to a reliable, independent and accurate measure of some isotopes activity. The last part presents the abstracts of researches activities from 1996 to 2001 on the tetravalent actinides phosphates chemistry, the sintering of PDT and solid solutions of PDTU and the kinetic and thermodynamical studies of the PDT dissolution. Many references and some publication in full text are provided. (A.L.B.)

Multi-element isotope dilution analyses using ICP-MS

International Nuclear Information System (INIS)

Volpe, A.M.

1996-01-01

Presently, 37 elements ranging from light (Li,B) through transition metals, noble, rare earth and heavy elements, to actinides and transuranics (Pu, Am, Cm) are measured by isotope dilution at Lawrence Livermore National Laboratory. Projects range from geological and hydrological to biological. The research goal is to measure accurately many elements present in diverse matrices at trace (ppb) levels using isotope dilution methods. Major advantages of isotope dilution methods are accuracy, elimination of ion intensity calibration, and quantitation for samples that require chemical separation. Accuracy depends on tracer isotope calibration, tracer-sample isotopic equilibration, and appropriate background, isobaric and mass bias corrections. Propagation of isotope ratio error due to improper tracer isotope addition is a major concern with multi-element analyses when abundances vary widely. 11 refs., 3 figs

Actinides transmutation - a comparison of results for PWR benchmark

International Nuclear Information System (INIS)

Claro, Luiz H.

2009-01-01

The physical aspects involved in the Partitioning and Transmutation (P and T) of minor actinides (MA) and fission products (FP) generated by reactors PWR are of great interest in the nuclear industry. Besides these the reduction in the storage of radioactive wastes are related with the acceptability of the nuclear electric power. From the several concepts for partitioning and transmutation suggested in literature, one of them involves PWR reactors to burn the fuel containing plutonium and minor actinides reprocessed of UO 2 used in previous stages. In this work are presented the results of the calculations of a benchmark in P and T carried with WIMSD5B program using its new cross sections library generated from the ENDF-B-VII and the comparison with the results published in literature by other calculations. For comparison, was used the benchmark transmutation concept based in a typical PWR cell and the analyzed results were the k∞ and the atomic density of the isotopes Np-239, Pu-241, Pu-242 and Am-242m, as function of burnup considering discharge of 50 GWd/tHM. (author)

Recent Improvements at CEA on Trace Analysis of Actinides in Environmental Samples

International Nuclear Information System (INIS)

Pointurier, F.; Hubert, A.; Faure, A.L.; Pottin, A.C.; Mourier, W.; Marie, O.

2010-01-01

In this paper, we present some results of R and D works conducted at CEA to improve on the one side the performance of the techniques already in use for detection of undeclared activities, and on the other side to develop new capabilities, either as alternative to the existing techniques or new methods that bring new information, complementary to the isotopic composition. For the trace analysis of plutonium in swipe samples by ICP-MS, we demonstrate that a thorough knowledge of the background in the actinide mass range is highly desirable. In order to avoid false plutonium detection in the femtogram range, correction from polyatomic interferences including mercury, lead or iridium atoms are in some case necessary. Efforts must be put on improving the purification procedure. Micro-Raman spectrometry allows determining the chemical composition of uranium compound at the scale of the microscopic object using a pre-location of the particles thanks to SEM and a relocation of these particles thanks to mathematical calculations. However, particles below 5 μm are hardly relocated and a coupling device between the SEM and the micro-Raman spectrometer for direct Raman analysis after location of a particle of interest is currently under testing. Lastly, laser ablation - ICP-MS is an interesting technique for direct isotopic or elemental analysis of various solid samples and proves to be a suitable alternative technique for particle analysis, although precision over isotopic ratio measurement is strongly limited by the short duration and irregularity of the signals. However, sensitivity and sample throughput are high and more developments are in progress to validate and improve this method. (author)

Actinide recycle

Energy Technology Data Exchange (ETDEWEB)

Till, C; Chang, Y [Argonne National Laboratory, Argonne, IL (United States)

1990-07-01

A multitude of studies and assessments of actinide partitioning and transmutation were carried out in the late 1970s and early 1980s. Probably the most comprehensive of these was a study coordinated by Oak Ridge National Laboratory. The conclusions of this study were that only rather weak economic and safety incentives existed for partitioning and transmuting the actinides for waste management purposes, due to the facts that (1) partitioning processes were complicated and expensive, and (2) the geologic repository was assumed to contain actinides for hundreds of thousands of years. Much has changed in the few years since then. A variety of developments now combine to warrant a renewed assessment of the actinide recycle. First of all, it has become increasingly difficult to provide to all parties the necessary assurance that the repository will contain essentially all radioactive materials until they have decayed. Assurance can almost certainly be provided to regulatory agencies by sound technical arguments, but it is difficult to convince the general public that the behavior of wastes stored in the ground can be modeled and predicted for even a few thousand years. From this point of view alone there would seem to be a clear benefit in reducing the long-term toxicity of the high-level wastes placed in the repository.

Actinide recycle

International Nuclear Information System (INIS)

Till, C.; Chang, Y.

1990-01-01

A multitude of studies and assessments of actinide partitioning and transmutation were carried out in the late 1970s and early 1980s. Probably the most comprehensive of these was a study coordinated by Oak Ridge National Laboratory. The conclusions of this study were that only rather weak economic and safety incentives existed for partitioning and transmuting the actinides for waste management purposes, due to the facts that (1) partitioning processes were complicated and expensive, and (2) the geologic repository was assumed to contain actinides for hundreds of thousands of years. Much has changed in the few years since then. A variety of developments now combine to warrant a renewed assessment of the actinide recycle. First of all, it has become increasingly difficult to provide to all parties the necessary assurance that the repository will contain essentially all radioactive materials until they have decayed. Assurance can almost certainly be provided to regulatory agencies by sound technical arguments, but it is difficult to convince the general public that the behavior of wastes stored in the ground can be modeled and predicted for even a few thousand years. From this point of view alone there would seem to be a clear benefit in reducing the long-term toxicity of the high-level wastes placed in the repository

Radium isotopes as a tool for the study of water mixing in the Paraiba do Sul River Estuary

International Nuclear Information System (INIS)

Souza, Thaisa Abreu de; Moreira, Isabel M.N.S.; Rezende, Carlos E. de

2008-01-01

Four isotopes of radium with different half-lives exist in nature. In aquatic systems, radium isotopes present distinct characteristics in salt water and fresh water environments. In fresh waters, radium appears adsorbed to particulate material while in sea water radium presents a conservative behavior, being the concentration of different isotopes of radium governed by the processes of dilution, advection and diffusion, as well as radioactive decay. The four natural isotopes of radium are tracers extensively used to determine ratios of water mixture and to calculate the period since the radium was added to the water column. The short-lived isotopes, 223 Ra (half-life = 11.4 days) and 224 Ra (half-life = 3.66 days), are continually regenerated from decay of their thorium parents, which are perpetually bound to particles surfaces. On the other hand, the long-lived isotopes, 226 Ra (half-life = 1600 yrs) and 228 Ra (half-life = 5.7 yrs), require considerable time for regeneration. These fluxes must be sustained by input water from rivers, sediments, SGD, or other sources. In the present work, developed at the estuary of the Paraiba do Sul River, the short half-lived radium isotopes ( 224 Ra and 223 Ra) were determined using the technique of coincidence delayed developed. The isotopes of long half-lifed ( 22 26Ra and 22 28Ra) were determined by the technique of total alpha and beta counting, after the dissolution of the MnO 2 fiber used to pre-concentrate radium. (author)

Structural organization and spectroscopy of peptide-actinide(IV) complexes

International Nuclear Information System (INIS)

Dahou, S.

2010-01-01

The contamination of living organisms by actinide elements is at the origin of both radiological and chemical toxicity that may lead to severe dysfunction. Most of the data available on the actinide interaction with biological systems are macroscopic physiological measurements and are lacking a molecular description of the systems. Because of the intricacy of these systems, classical biochemical methods are difficult to implement. Our strategy consisted in designing simplified biomimetic peptides, and describing the corresponding intramolecular interactions with actinides. A carboxylic pentapeptide of the form DDPDD has been at the starting point of this work in order to further assess the influence of the peptide sequence on the topology of the complexes.To do so, various linear (Asp/Ala permutations, peptoids) and cyclic analogues have been synthesized. Furthermore, in order to include the hydroxamic function (with a high affinity for Fe(III)) in the peptide, both desferrioxamine and acetohydroxamic acid have been investigated. However because of difficulties in synthesis, we have not been able to test these peptides. Three actinide cations have been considered at oxidation state +IV (Th, Np, Pu) and compared to Fe(III), often considered as a biological surrogate of Pu(IV). The spatial arrangement of the peptide around the cation has been probed by spectrophotometry and X-ray Absorption Spectroscopy. The spectroscopic data and EXAFS data adjustment lead us to rationalize the topology of the complexes as a function of the peptide sequence: mix hydroxy polynuclear species for linear and cyclic peptides, mononuclear for the desferrioxamine complexes. Furthermore, significant differences have appeared between Fe(III) and actinide(IV), related to differences of reactivity in aqueous medium. (author)

Proposed partitioning and transmutation of long-lived nuclear wastes

International Nuclear Information System (INIS)

Van Tuyle, G.J.; Rawlins, J.A.

1991-01-01

A means of transmuting key long-lived nuclear wastes, primarily the minor actinides (Np, Am, Cm) and iodine, using a hybrid proton accelerator and sub-critical lattice, is proposed. By partitioning light water reactor (LWR) spent fuel and by transmuting key elements, such as the plutonium, the minor actinides, and a few of the long-lived fission products, some of the most significant challenges in building a waste repository can be substantially reduced. The proposed machine would transmute the minor actinides and the iodine produced by 75 LWRs, and would generate usable electricity (beyond that required to run the large accelerator) of 850 MW e . 14 refs., 10 figs

Removal of actinides from high-level wastes generated in the reprocessing of commercial fuels

International Nuclear Information System (INIS)

Bond, W.D.; Leuze, R.E.

1975-09-01

Progress is reported on a technical feasibility study of removing the very long-lived actinides (uranium, neptunium, plutonium, americium, and curium) from high-level wastes generated in the commercial reprocessing of spent nuclear fuels. The study was directed primarily at wastes from the reprocessing of light water reactor (LWR) fuels and specifically to developing satisfactory methods for reducing the actinide content of these wastes to values that would make 1000-year-decayed waste comparable in radiological toxicity to natural uranium ore deposits. Although studies are not complete, results thus far indicate the most promising concept for actinide removal includes both improved recovery of actinides in conventional fuel reprocessing and secondary processing of the high-level wastes. Secondary processing will be necessary for the removal of americium and curium and perhaps some residual plutonium. Laboratory-scale studies of separations methods that appear most promising are reported and conceptual flowsheets are discussed. (U.S.)

SACSESS – the EURATOM FP7 project on actinide separation from spent nuclear fuels

Directory of Open Access Journals (Sweden)

Bourg Stéphane

2015-12-01

Full Text Available Recycling of actinides by their separation from spent nuclear fuel, followed by transmutation in fast neutron reactors of Generation IV, is considered the most promising strategy for nuclear waste management. Closing the fuel cycle and burning long-lived actinides allows optimizing the use of natural resources and minimizing the long-term hazard of high-level nuclear waste. Moreover, improving the safety and sustainability of nuclear power worldwide. This paper presents the activities striving to meet these challenges, carried out under the Euratom FP7 collaborative project SACSESS (Safety of Actinide Separation Processes. Emphasis is put on the safety issues of fuel reprocessing and waste storage. Two types of actinide separation processes, hydrometallurgical and pyrometallurgical, are considered, as well as related aspects of material studies, process modeling and the radiolytic stability of solvent extraction systems. Education and training of young researchers in nuclear chemistry is of particular importance for further development of this field.

Microcomputer-based systems for automatic control of sample irradiation and chemical analysis of short-lived isotopes

International Nuclear Information System (INIS)

Bourret, S.C.

1974-01-01

Two systems resulted from the need for the study of the nuclear decay of short-lived radionuclides. Automation was required for better repeatability, speed of chemical separation after irradiation and for protection from the high radiation fields of the samples. A MCS-8 computer was used as the nucleus of the automatic sample irradiation system because the control system required an extensive multiple-sequential circuit. This approach reduced the sequential problem to a computer program. The automatic chemistry control system is a mixture of a fixed and a computer-based programmable control system. The fixed control receives the irradiated liquid sample from the reactor, extracts the liquid and disposes of the used sample container. The programmable control executes the chemistry program that the user has entered through the teletype. (U.S.)

Actinide transmutation using inert matrix fuels versus recycle in a low conversion fast burner reactor

Energy Technology Data Exchange (ETDEWEB)

Deinert, M.R.; Schneider, E.A.; Recktenwald, G.; Cady, K.B. [The Department of Mechanical Engineering, The University of Texas at Austin, 1 University Station, C2200, Austin, 78712 (United States)

2009-06-15

Reducing the disposal burden of the long lived radioisotopes that are contained within spent uranium oxide fuel is essential for ensuring the sustainability of nuclear power. Because of their non-fertile matrices, inert matrix fuels (IMFs) could allow light-water reactors to achieve a significant burn down of plutonium and minor actinides that are that are currently produced as a byproduct of operating light-water reactors. However, the extent to which this is possible is not yet fully understood. We consider a ZrO{sub 2} based IMF with a high transuranic loading and show that the neutron fluence (and the subsequent fuel residence time required to achieve it) present a practical limit for the achievable actinide burnup. The accumulation of transuranics in spent uranium oxide fuel is a major obstacle for the sustainability of nuclear power. While commercial light-water reactors (LWR's) produce these isotopes, they can be used to transmute them. At present, the only viable option for doing this is to partly fuel reactors with mixed oxide fuel (MOX) made using recycled plutonium. However, because of parasitic neutron capture in the uranium matrix of MOX, considerable plutonium and minor actinides are also bred as the fuel is burned. A better option is to entrain the recycled isotopes in a non-fertile matrix such as ZrO{sub 2}. Inert matrices such as these were originally envisioned for burning plutonium from dismantled nuclear weapons [1]. However, because they achieve a conversion ratio of zero, they have also been considered as a better alternative to MOX [2-6]. Plutonium and minor actinides dominate the long term heat and radiological outputs from spent nuclear fuel. Recent work has shown that that IMFs can be used to reduce these outputs by at least a factor of four, on a per unit of energy generated basis [6]. The degree of reduction is strongly dependent on IMF burnup. In principle, complete transmutation of the transuranics could be achieved though this

Recent development in computational actinide chemistry

International Nuclear Information System (INIS)

Li Jun

2008-01-01

Ever since the Manhattan project in World War II, actinide chemistry has been essential for nuclear science and technology. Yet scientists still seek the ability to interpret and predict chemical and physical properties of actinide compounds and materials using first-principle theory and computational modeling. Actinide compounds are challenging to computational chemistry because of their complicated electron correlation effects and relativistic effects, including spin-orbit coupling effects. There have been significant developments in theoretical studies on actinide compounds in the past several years. The theoretical capabilities coupled with new experimental characterization techniques now offer a powerful combination for unraveling the complexities of actinide chemistry. In this talk, we will provide an overview of our own research in this field, with particular emphasis on applications of relativistic density functional and ab initio quantum chemical methods to the geometries, electronic structures, spectroscopy and excited-state properties of small actinide molecules such as CUO and UO 2 and some large actinide compounds relevant to separation and environment science. The performance of various density functional approaches and wavefunction theory-based electron correlation methods will be compared. The results of computational modeling on the vibrational, electronic, and NMR spectra of actinide compounds will be briefly discussed as well [1-4]. We will show that progress in relativistic quantum chemistry, computer hardware and computational chemistry software has enabled computational actinide chemistry to emerge as a powerful and predictive tool for research in actinide chemistry. (authors)

Isotope products manufacture in Russia and its prospects

International Nuclear Information System (INIS)

Malyshev, S.V.; Okhotina, I.A.; Kalelin, E.A.; Krasnov, N.N.; Kuzin, V.V.; Malykh, J.A.; Makarovsky, S.B.

1997-01-01

At the present stage of the world economy development, stable and radioactive isotopes,preparations and products on their base are widely used in many fields of the national economy, medicine and scientific researches. The Russian Federation is one of the largest worldwide producers of a variety of nuclide products on the base of more than 350 isotopes, as follows: stable isotopes reactor, cyclotron, fission product radioactive isotopes, ion-radiation sources compounds, labelled with stable and radioactive isotopes, radionuclide short-lived isotope generators, radiopharmaceuticals, radionuclide light and heat sources; luminous paints on base of isotopes. The Russian Ministry for Atomic Energy coordinates activity for development and organization of manufacture and isotope products supply in Russia as well as for export. Within many years of isotope industry development, there have appeared some manufacturing centres in Russia, dealing with a variety of isotope products. The report presents the production potentialities of these centres and also an outlook on isotope production development in Russia in the next years

The origin and disappearance of the late Pleistocene-early Holocene short-lived coastal wetlands along the Carmel coast, Israel

Science.gov (United States)

Sivan, Dorit; Greenbaum, Noam; Cohen-Seffer, Ronit; Sisma-Ventura, Guy; Almogi-Labin, Ahuva

The formation of short-lived backswamps along the Carmel coast of Israel coincides with the rapid global sea-level rise during the late Pleistocene-early Holocene transition. The current study shows that the wetland phenomena originated around 10,000 yr ago and dried up shortly before the local Pre-Pottery Neolithic humans settled on the wetland dark clay sediments 9430 cal yr BP. Palaeontological and stable-isotope data were used in this study to elucidate previously published sedimentological reconstruction obtained from a core drilled into the western trough of the Carmel coastal plain. The water body contained typical brackish calcareous fauna, with variable numerical abundance and low species richness of ostracods and foraminifera. The δ 18O and δ 13C of the ostracod Cyprideis torosa show close similarity to the present Pleistocene coastal aquifer isotopic values. This study therefore concludes that the wetlands were shallow-water bodies fed by groundwater, with no evidence of sea-water mixing. It seems that they developed as the result of high groundwater levels, transportation of sediments landward, and deposition of sand bars at the paleo-river mouths. It is still not fully understood why these wetlands deteriorated abruptly and disappeared within less than 1000 yr.

Isotope and Nuclear Chemistry Division annual report, FY 1983

International Nuclear Information System (INIS)

Heiken, J.H.; Lindberg, H.A.

1984-05-01

This report describes progress in the major research and development programs carried out in FY 1983 by the Isotope and Nuclear Chemistry Division. It covers radiochemical diagnostics of weapons tests; weapons radiochemical diagnostics research and development; other unclassified weapons research; stable and radioactive isotope production, separation, and applications (including biomedical applications); element and isotope transport and fixation; actinide and transition metal chemistry; structural chemistry, spectroscopy, and applications; nuclear structure and reactions; irradiation facilities; advanced analytical techniques; development and applications; atmospheric chemistry and transport; and earth and planetary processes

Isotope and Nuclear Chemistry Division annual report, FY 1983

Energy Technology Data Exchange (ETDEWEB)

Heiken, J.H.; Lindberg, H.A. (eds.)

1984-05-01

This report describes progress in the major research and development programs carried out in FY 1983 by the Isotope and Nuclear Chemistry Division. It covers radiochemical diagnostics of weapons tests; weapons radiochemical diagnostics research and development; other unclassified weapons research; stable and radioactive isotope production, separation, and applications (including biomedical applications); element and isotope transport and fixation; actinide and transition metal chemistry; structural chemistry, spectroscopy, and applications; nuclear structure and reactions; irradiation facilities; advanced analytical techniques; development and applications; atmospheric chemistry and transport; and earth and planetary processes.

Isotope and Nuclear Chemistry Division annual report, FY 1984

International Nuclear Information System (INIS)

Heiken, J.H.

1985-04-01

This report describes progress in the major research and development programs carried out in FY 1984 by the Isotope and Nuclear Chemistry Division. It covers radiochemical diagnostics of weapons tests; weapons radiochemical diagnostics research and development; other unclassified weapons research; stable and radioactive isotope production, separation, and applications (including biomedical applications); element and isotope transport and fixation; actinide and transition metal chemistry; structural chemistry, spectroscopy, and applications; nuclear structure and reactions; irradiation facilities; advanced analytical techniques: development and applications; atmospheric chemistry and transport; and earth and planetary processes. 287 refs

Actinide recovery techniques utilizing electromechanical processes

International Nuclear Information System (INIS)

Westphal, B.R.; Benedict, R.W.

1994-01-01

Under certain conditions, the separation of actinides using electromechanical techniques may be an effective means of residue processing. The separation of granular mixtures of actinides and other materials is based on appreciable differences in the magnetic and electrical properties of the actinide elements. In addition, the high density of actinides, particularly uranium and plutonium, may render a simultaneous separation based on mutually complementary parameters. Both high intensity magnetic separation and electrostatic separation have been investigated for the concentration of an actinide waste stream. Waste stream constituents include an actinide metal alloy and broken quartz shards. The investigation of these techniques is in support of the Integral Fast Reactor (IFR) concept currently being developed at Argonne National Laboratory under the auspices of the Department of Energy

182Hf-182W age dating of a 26Al-poor inclusion and implications for the origin of short-lived radioisotopes in the early Solar System.

Science.gov (United States)

Holst, Jesper C; Olsen, Mia B; Paton, Chad; Nagashima, Kazuhide; Schiller, Martin; Wielandt, Daniel; Larsen, Kirsten K; Connelly, James N; Jørgensen, Jes K; Krot, Alexander N; Nordlund, Ake; Bizzarro, Martin

2013-05-28

Refractory inclusions [calcium-aluminum-rich inclusions, (CAIs)] represent the oldest Solar System solids and provide information regarding the formation of the Sun and its protoplanetary disk. CAIs contain evidence of now extinct short-lived radioisotopes (e.g., (26)Al, (41)Ca, and (182)Hf) synthesized in one or multiple stars and added to the protosolar molecular cloud before or during its collapse. Understanding how and when short-lived radioisotopes were added to the Solar System is necessary to assess their validity as chronometers and constrain the birthplace of the Sun. Whereas most CAIs formed with the canonical abundance of (26)Al corresponding to (26)Al/(27)Al of ∼5 × 10(-5), rare CAIs with fractionation and unidentified nuclear isotope effects (FUN CAIs) record nucleosynthetic isotopic heterogeneity and (26)Al/(27)Al of Solar System, including the origin of short-lived radioisotopes. However, their chronology is unknown. Using the (182)Hf-(182)W chronometer, we show that a FUN CAI recording a condensation origin from a solar gas formed coevally with canonical CAIs, but with (26)Al/(27)Al of ∼3 × 10(-6). The decoupling between (182)Hf and (26)Al requires distinct stellar origins: steady-state galactic stellar nucleosynthesis for (182)Hf and late-stage contamination of the protosolar molecular cloud by a massive star(s) for (26)Al. Admixing of stellar-derived (26)Al to the protoplanetary disk occurred during the epoch of CAI formation and, therefore, the (26)Al-(26)Mg systematics of CAIs cannot be used to define their formation interval. In contrast, our results support (182)Hf homogeneity and chronological significance of the (182)Hf-(182)W clock.

Criteria for achieving actinide reduction goals

International Nuclear Information System (INIS)

Liljenzin, J.O.

1996-01-01

In order to discuss various criteria for achieving actinide reduction goals, the goals for actinide reduction must be defined themselves. In this context the term actinides is interpreted to mean plutonium and the so called ''minor actinides'' neptunium, americium and curium, but also protactinium. Some possible goals and the reasons behind these will be presented. On the basis of the suggested goals it is possible to analyze various types of devices for production of nuclear energy from uranium or thorium, such as thermal or fast reactors and accelerator driven system, with their associated fuel cycles with regard to their ability to reach the actinide reduction goals. The relation between necessary single cycle burn-up values, fuel cycle processing losses and losses to waste will be defined and discussed. Finally, an attempt is made to arrange the possible systems on order of performance with regard to their potential to reduce the actinide inventory and the actinide losses to wastes. (author). 3 refs, 3 figs, 2 tabs

Emission channeling with short-lived isotopes lattice location of impurities in semiconductors and oxides

CERN Multimedia

We propose to perform emission channeling lattice location experiments in a number of semiconductor and oxide systems of technological relevance: \\\\- The lattice location of the transition metal probes $^{56}$Mn ($\\textit{t}_{1/2}$=2.6 h), $^{59}$Fe (45 d), $^{61}$Co (1.6 h) and $^{65}$Ni (2.5 h) is to be investigated in materials of interest as dilute magnetic semiconductors, such as GaMnAs, GaMnN, GaFeN, AlGaN, SiC, and in a number of oxides that are candidates for “single ion ferromagnetism”, in particular SrTiO$_3$ and LiNbO$_3$.\\\\- The topic of $\\textit{p}$-type doping of nitride semiconductors shall be addressed by studying the lattice sites of the acceptor dopants Mg and Be in GaN and AlN using the short-lived probes $^{27}$Mg (9.5 min) and $^{11}$Be (13.8 s). The aim is to reach a lattice location precision around 0.05 Å in order to provide critical tests for recent theoretical models which e.g. have predicted displacements of the Mg atom from the ideal substitutional Ga and Al sites of the order...

Accuracy Improvement of Neutron Nuclear Data on Minor Actinides

Science.gov (United States)

Harada, Hideo; Iwamoto, Osamu; Iwamoto, Nobuyuki; Kimura, Atsushi; Terada, Kazushi; Nakao, Taro; Nakamura, Shoji; Mizuyama, Kazuhito; Igashira, Masayuki; Katabuchi, Tatsuya; Sano, Tadafumi; Takahashi, Yoshiyuki; Takamiya, Koichi; Pyeon, Cheol Ho; Fukutani, Satoshi; Fujii, Toshiyuki; Hori, Jun-ichi; Yagi, Takahiro; Yashima, Hiroshi

2015-05-01

Improvement of accuracy of neutron nuclear data for minor actinides (MAs) and long-lived fission products (LLFPs) is required for developing innovative nuclear system transmuting these nuclei. In order to meet the requirement, the project entitled as "Research and development for Accuracy Improvement of neutron nuclear data on Minor ACtinides (AIMAC)" has been started as one of the "Innovative Nuclear Research and Development Program" in Japan at October 2013. The AIMAC project team is composed of researchers in four different fields: differential nuclear data measurement, integral nuclear data measurement, nuclear chemistry, and nuclear data evaluation. By integrating all of the forefront knowledge and techniques in these fields, the team aims at improving the accuracy of the data. The background and research plan of the AIMAC project are presented.

In-beam study of the rotational states in actinides after alpha-induced nuclear reactions

International Nuclear Information System (INIS)

Hardt, K.

1983-01-01

In the experiments described in this thesis the ground state rotational bands of a whole series of actinide isotopes has been studied by means of α-induced nuclear reactions. The rotational bands studied in the even isotopes could be identified up to a spin of about 16 (h/2π). With this data it was now possible to establish a broad systematic of the rotational energies up to relatively high angular momenta. Also in the odd isotopes 233 U and 239 Pu it was possible to follow the ground state rotational bands up to higher spins and to compare them with predictions of the rotational model. By means of the (α,α'2n) reaction the nuclei 230 Th and especially 228 Th could by populated. (orig./HSI) [de

Actinides: why are they important biologically

International Nuclear Information System (INIS)

Durbin, P.W.

1978-01-01

The following topics are discussed: actinide elements in energy systems; biological hazards of the actinides; radiation protection standards; and purposes of actinide biological research with regard to toxicity, metabolism, and therapeutic regimens

Measurement of short-lived particles at PETRA

International Nuclear Information System (INIS)

Saxon, D.H.

1987-04-01

The contribution of PETRA to the measurement of short-lived particles is reviewed with discussion of the detectors and analysis techniques. New results are presented on lifetimes of identified particles and the systematics of b-life measurement outlined. The first application of vertex-tagging to flavour separation is described. (author)

New neutron-deficient isotopes of barium and rare-earth elements

CERN Document Server

Bogdanov, D D; Karnaukhov, V A; Petrov, L A; Plochocki, A; Subbotin, V G; Voboril, J

1976-01-01

The authors present an investigation of the short-lived neutron- deficient isotopes of barium and rare-earth elements. By using the BEMS-2 isotope separator on a heavy ion beam, 19 new isotopes were produced with mass numbers ranging from 117 to 138. Five of these (/sup 117/Ba, /sup 129,131/Nd and /sup 133,135/Sm) turned out to be delayed proton emitters. The beta -decay probabilities for the new isotopes have been analyzed in terms of the beta -strength function. An analysis of the proton spectrum shape has been performed using the statistical model for delayed proton emission.

Safe management of actinides in the nuclear fuel cycle: Role of mineralogy

International Nuclear Information System (INIS)

Ewing, R.C.

2011-01-01

During the past 60 years, more than 1800 metric tonnes of Pu, and substantial quantities of the 'minor' actinides, such as Np, Am and Cm, have been generated in nuclear reactors. Some of these transuranium elements can be a source of energy in fission reactions (e.g., 239 Pu), a source of fissile material for nuclear weapons (e.g., 239 Pu and 237 Np), and of environmental concern because of their long-half lives and radiotoxicity (e.g., 239 Pu and 237 Np). There are two basic strategies for the disposition of these heavy elements: (1) to 'burn' or transmute the actinides using nuclear reactors or accelerators; (2) to 'sequester' the actinides in chemically durable, radiation-resistant materials that are suitable for geologic disposal. There has been substantial interest in the use of actinide-bearing minerals, especially isometric pyrochlore, A 2 B 2 O 7 (A rare earths; B = Ti, Zr, Sn, Hf), for the immobilization of actinides, particularly plutonium, both as inert matrix fuels and nuclear waste forms. Systematic studies of rare-earth pyrochlores have led to the discovery that certain compositions (B = Zr, Hf) are stable to very high doses of alpha-decay event damage. Recent developments in our understanding of the properties of heavy element solids have opened up new possibilities for the design of advanced nuclear fuels and waste forms. (author)

Chemistry of tetravalent actinides phosphates. The thorium phosphate-diphosphate as immobilisation matrix of actinides; Chimie des phosphates d'actinides tetravalents. Le phosphate-diphosphate de thorium en tant que matrice d'imobilisation des actinides

Energy Technology Data Exchange (ETDEWEB)

Dacheux, N

2002-07-01

The author presents in this document its scientific works from 1992 to 2001, in order to obtain the enabling to manage scientific and chemical researches at the university Paris Sud Orsay. The first part gives an abstract of the thesis on the characterizations, lixiviation and synthesis of uranium and thorium based phosphate matrix in the framework of the search for a ceramic material usable in the radioactive waste storage. The second part presents briefly the researches realized at the CEA, devoted to a reliable, independent and accurate measure of some isotopes activity. The last part presents the abstracts of researches activities from 1996 to 2001 on the tetravalent actinides phosphates chemistry, the sintering of PDT and solid solutions of PDTU and the kinetic and thermodynamical studies of the PDT dissolution. Many references and some publication in full text are provided. (A.L.B.)

Safe management of actinides in the nuclear fuel cycle: Role of mineralogy; La gestion des actinides dans le cycle du combustible nucleaire: le role de la mineralogie

Energy Technology Data Exchange (ETDEWEB)

Ewing, R.C. [Department of Nuclear Engineering and Radiological Sciences, Department of Geological Sciences, Department of Materials Science and Engineering, University of Michigan, Ann Arbor, Michigan 48109-1005 (United States)

2011-02-15

During the past 60 years, more than 1800 metric tonnes of Pu, and substantial quantities of the 'minor' actinides, such as Np, Am and Cm, have been generated in nuclear reactors. Some of these transuranium elements can be a source of energy in fission reactions (e.g., {sup 239}Pu), a source of fissile material for nuclear weapons (e.g., {sup 239}Pu and {sup 237}Np), and of environmental concern because of their long-half lives and radiotoxicity (e.g., {sup 239}Pu and {sup 237}Np). There are two basic strategies for the disposition of these heavy elements: (1) to 'burn' or transmute the actinides using nuclear reactors or accelerators; (2) to 'sequester' the actinides in chemically durable, radiation-resistant materials that are suitable for geologic disposal. There has been substantial interest in the use of actinide-bearing minerals, especially isometric pyrochlore, A{sub 2}B{sub 2}O{sub 7} (A rare earths; B = Ti, Zr, Sn, Hf), for the immobilization of actinides, particularly plutonium, both as inert matrix fuels and nuclear waste forms. Systematic studies of rare-earth pyrochlores have led to the discovery that certain compositions (B = Zr, Hf) are stable to very high doses of alpha-decay event damage. Recent developments in our understanding of the properties of heavy element solids have opened up new possibilities for the design of advanced nuclear fuels and waste forms. (author)

The ratio of long-lived to short-lived radon-222 progeny concentrations in ground-level air

International Nuclear Information System (INIS)

Hoetzl, H.; Winkler, R.

1996-01-01

The ratio of 210 Pb air concentration to the short-lived radon ( 222 Rn) decay products concentration at ground level was investigated at a semi-rural location 10 km north of Munich, south Germany, for a period of 11 years (1982-1992). The average ratio from 132 monthly mean values has been found to be (7.5±2.2) x 10 -5 (arithmetic mean±S.D.). While the time series of the short-lived radon daughter concentration exhibit a distinct seasonal pattern with maxima mostly in October of each year, the course of 210 Pb air concentration is characterized by high values from October through February. Consequently, high ratios of 210 Pb to short-lived decay product concentration are often observed in the winter months of December-February. To study the influence of meteorological conditions on this behaviour, 210 Pb and 214 Pb concentrations were measured on a short-term basis with sampling intervals of 2-3 days from October 1991 to November 1992. The air concentrations obtained within those intervals were then correlated with actual meteorological parameters. On the base of this investigation the seasonal behaviour can essentially be explained by the more frequent inversion weather conditions in winter than in the summer months. At the same location, the average ratio of 210 Po to 210 Pb concentration in ground level air has been found to be 0.079 from 459 weakly mean values between 1976 and 1985. Hence, the corresponding average ratios of the short-lived radon daughters (EEC) to 210 Pb and 210 Po, were 1:7.5x10 -5 and 1:0.6 x 10 -5 , respectively

Actinide recovery techniques utilizing electromechanical processes

International Nuclear Information System (INIS)

Westphal, B.R.; Benedict, R.W.

1994-01-01

Under certain conditions, the separation of actinides using electromechanical techniques may be an effective means of residue processing. The separation of granular mixtures of actinides and other materials discussed in this report is based on appreciable differences in the magnetic and electrical properties of the actinide elements. In addition, the high density of actinides, particularly uranium and plutonium, may render a simultaneous separation based on mutually complementary parameters. Both high intensity magnetic separation and electrostatic separation have been investigated for the concentration of an actinide waste stream. Waste stream constituents include an actinide metal alloy and broken quartz shards. The investigation of these techniques is in support of the Integral Fast Reactor (IFR) concept currently being developed at Argonne National Laboratory under the auspices of the Department of Energy

Actinide Separation Demonstration Facility, Tarapur

International Nuclear Information System (INIS)

Vishwaraj, I.

2017-01-01

Partitioning of minor actinide from high level waste could have a substantial impact in lowering the radio toxicity associated with high level waste as well as it will reduce the burden on geological repository. In Indian context, the partitioned minor actinide could be routed into the fast breeder reactor systems scheduled for commissioning in the near period. The technological breakthrough in solvent development has catalyzed the partitioning programme in India, leading to the setting up and hot commissioning of the Actinide Separation Demonstration Facility (ASDF) at BARC, Tarapur. The engineering scale Actinide Separation Demonstration Facility (ASDF) has been retrofitted in an available radiological hot cell situated adjacent to the Advanced Vitrification Facility (AVS). This location advantage ensures an uninterrupted supply of high-level waste and facilitates the vitrification of the high-level waste after separation of minor actinides

High flux Particle Bed Reactor systems for rapid transmutation of actinides and long lived fission products

International Nuclear Information System (INIS)

Powell, J.; Ludewig, H.; Maise, G.; Steinberg, M.; Todosow, M.

1993-01-01

An initial assessment of several actinide/LLFP burner concepts based on the Particle Bed Reactor (PBR) is described. The high power density/flux level achievable with the PBR make it an attractive candidate for this application. The PBR based actinide burner concept also possesses a number of safety and economic benefits relative to other reactor based transmutation approaches including a low inventory of radionuclides, and high integrity, coated fuel particles which can withstand extremely high in temperatures while retaining virtually all fission products. In addition the reactor also posesses a number of ''engineered safety features,'' which, along with the use of high temperature capable materials further enhance its safety characteristics

Simulations of the Thermodynamic and Diffusion Properties of Actinide Oxide Fuel Materials

International Nuclear Information System (INIS)

Becker, Udo

2013-01-01

Spent nuclear fuel from commercial reactors is comprised of 95-99 percent UO 2 and 1-5 percent fission products and transuranic elements. Certain actinides and fission products are of particular interest in terms of fuel stability, which affects reprocessing and waste materials. The transuranics found in spent nuclear fuels are Np, Pu, Am, and Cm, some of which have long half- lives (e.g., 2.1 million years for 237 Np). These actinides can be separated and recycled into new fuel matrices, thereby reducing the nuclear waste inventory. Oxides of these actinides are isostructural with UO 2 , and are expected to form solid solutions. This project will use computational techniques to conduct a comprehensive study on thermodynamic properties of actinide-oxide solid solutions. The goals of this project are to: Determine the temperature-dependent mixing properties of actinide-oxide fuels; Validate computational methods by comparing results with experimental results; Expand research scope to complex (ternary and quaternary) mixed actinide oxide fuels. After deriving phase diagrams and the stability of solid solutions as a function of temperature and pressure, the project team will determine whether potential phase separations or ordered phases can actually occur by studying diffusion of cations and the kinetics of potential phase separations or ordered phases. In addition, the team will investigate the diffusion of fission product gases that can also have a significant influence on fuel stability. Once the system has been established for binary solid solutions of Th, U, Np, and Pu oxides, the methodology can be quickly applied to new compositions that apply to ternaries and quaternaries, higher actinides (Am, Cm), burnable poisons (B, Gd, Hf), and fission products (Cs, Sr, Tc) to improve reactivity

Actinide recycling in reactors; Aktiniden-Rezyklierung in Reaktoren

Energy Technology Data Exchange (ETDEWEB)

Kuesters, H.; Wiese, H.W.; Krieg, B.

1995-08-01

The objective is an assessment of the transmutation of long-lived actinides and fission products and the incineration of plutonium for reducing the risk potential of radioactive waste from reactors in comparison to direct waste disposal. The contribution gives an interim account on homogeneous and heterogeneous recycling of `risk nuclides` in thermal and fast reactors. Important results: - A homogeneous 5 percent admixture of minor actinides (MA) from N4-PWRs to EFR fuel would allow a transmutation not only of the EFR MA, but in addition of the MA from 5 or 6 PWRs of equal power. However, the incineration is restricted by safety considerations. - LWR have only a very low MA incineration potential, due to their disadvantageous neutron capture/fission ratio. - In order to keep the Cm inventory at a low level, it is advantageous to concentrate the Am heterogeneously in particular fuel elements or rods. (orig./HP)

Evaluation on transmutation performance of minor actinides with high-flux BWR

International Nuclear Information System (INIS)

Setiawan, M.B.; Kitamoto, A.; Taniguchi, A.

2001-01-01

The performance of high-flux BWR (HFBWR) for burning and/or transmutation (B/T) treatment of minor actinides (MA) and long-lived fission products (LLFP) was discussed herein for estimating an advanced waste disposal with partitioning and transmutation (P and T). The concept of high-flux B/T reactor was based on a current 33 GWt-BWR, to transmute the mass of long-lived transuranium (TRU) to short-lived fission products (SLFP). The nuclide selected for B/T treatment was MA (Np-237, Am-241, and Am-243) included in the discharged fuel of LWR. The performance of B/T treatment of MA was evaluated by a new function, i.e. [F/T ratio], defined by the ratio of the fission rate to the transmutation rate in the core, at an arbitrary burn-up, due to all MA nuclides. According to the results, HFBWR could burn and/or transmute MA nuclides with higher fission rate than BWR, but the fission rate did not increase proportionally to the flux increment, due to the higher rate of neutron adsorption. The higher B/T fraction of MA would result in the higher B/T capacity, and will reduce the units of HFBWR needed for the treatment of a constant mass of MA. In addition, HFBWR had a merit of higher mass transmutation compared to the reference BWR, under the same mass loading of MA

A survey of selected neutron-activation reactions with short-lived products of importance to fusion reactor technology

International Nuclear Information System (INIS)

Ward, R.C.; Gomes, I.C.; Smith, D.L.

1994-11-01

The status of the cross sections for production of short-lived radioactivities in the intense high-energy neutron fields associated with D-T fusion reactors is investigated. The main concerns relative to these very radioactive isotopes are with radiation damage to sensitive components such as superconducting magnets, the decay-heat problem and the safety of personnel during operation of the facility. The present report surveys the status of nuclear data required to assess these problems. The study is limited to a few high-priority nuclear reactions which appear to be of critical concern in this context. Other reactions of lesser concern are listed but are not treated in the present work. Among the factors that were considered in defining the relevant reactions and setting priorities are: quantities of the elemental materials in a fusion reactor, isotopic abundances within elemental categories, the decay properties of the induced radioactive byproducts, the reaction cross sections, and the nature of the decay radiations. Attention has been focused on radioactive species with half lives in the range from about 1 second to 15 minutes. Available cross-section and reaction-product decay information from the literature has been compiled and included in the report. Uncertainties have been estimated by examining several sets of experimental as well as evaluated data. Comments on the general status of data for various high-priority reactions are offered. On the basis of this investigation, it has been found that the nuclear data are in reasonably good shape for some of the most important reactions but are unacceptable for others. Based on this investigation, the reactions which should be given the greatest attention are: 16 O(n,p) 16 N, 55 Mn(n,p) 55 Cr, 57 Fe(n,p) 57 Mn, 186 W(n,2n) 185m W, and 207 Pb(n,n') 207m Pb. However, the development of fusion power would benefit from an across-the-board refinement in these nuclear data so that a more accurate quantitative

Concentration of actinides in the food chain

International Nuclear Information System (INIS)

Bulman, R.A.

1976-06-01

Considerable concern is now being expressed over the discharge of actinides into the environment. This report presents a brief review of the chemistry of the actinides and examines the evidence for interaction of the actinides with some naturally-occurring chelating agents and other factors which might stimulate actinide concentration in the food chain of man. This report also reviews the evidence for concentration of actinides in plants and for uptake through the gastrointestinal tract. (author)

Thermal-hydraulics of actinide burner reactors

International Nuclear Information System (INIS)

Takizuka, Takakazu; Mukaiyama, Takehiko; Takano, Hideki; Ogawa, Toru; Osakabe, Masahiro.

1989-07-01

As a part of conceptual study of actinide burner reactors, core thermal-hydraulic analyses were conducted for two types of reactor concepts, namely (1) sodium-cooled actinide alloy fuel reactor, and (2) helium-cooled particle-bed reactor, to examine the feasibility of high power-density cores for efficient transmutation of actinides within the maximum allowable temperature limits of fuel and cladding. In addition, calculations were made on cooling of actinide fuel assembly. (author)

Release studies of a thin foil tantalum target for the production of short-lived radioactive nuclei

CERN Document Server

Bennett, J R J; Drumm, P V; Lettry, Jacques; Nilsson, T; Catherall, R; Jonsson, O C; Ravn, H L; Simon, H

2002-01-01

Measurements have been made at ISOLDE, of the release curves and yields of radioactive beams of lithium, sodium and beryllium from a target constructed from 2 $\\mu$m thick foils. The release curves have been analysed by fitting to a mathematical model to determine the coefficients of diffusion of the particles in the foils and effusion through the target and ionizer at several temperatures. Through a better understanding of the rate of transport of the particles, it is possible to design targets and ionizers with improved yields. This is most important for the rare, short-lived isotopes in which there is considerable interest for physics experiments. This target has demonstrated large increases in the yields of $^{11}$Li and $^{12}$Be, in agreement with the predictions of the model. (11 refs).

Microscopic study of positive-parity yrast bands of Th isotopes

Indian Academy of Sciences (India)

tor arrays. Thorium is one of the isotopic mass chains that has been studied. The level ... the valence space and np-interaction in SOP orbits plays a crucial role in determining the ..... parameters suggested by Rozmej [37] in the actinide region.

Actinides record, power calculations and activity for present isotopes in the spent fuel of a BWR

International Nuclear Information System (INIS)

Enriquez C, P.; Ramirez S, J. R.; Lucatero, M. A.

2012-10-01

The administration of spent fuel is one of the more important stages of the nuclear fuel cycle, and this has become a problem of supreme importance in countries that possess nuclear reactors. Due to this in this work, the study on the actinides record and present fission products to the discharge of the irradiated fuel in a light water reactor type BWR is shown, to quantify the power and activity that emit to the discharge and during the cooling time. The analysis was realized on a fuel assembly type 10 x 10 with an enrichment average of 3.69 wt % in U-235 and the assembly simulation assumes four cycles of operation of 18 months each one and presents an exposition of 47 G Wd/Tm to the discharge. The module OrigenArp of the Scale 6 code is the computation tool used for the assembly simulation and to obtain the results on the actinides record presents to the fuel discharge. The study covers the following points: a) Obtaining of the plutonium vector used in the fuel production of mixed oxides, and b) Power calculation and activity for present actinides to the discharge. The results presented in this work, correspond at the same time immediate of discharge (0 years) and to a cooling stage in the irradiated fuel pool (5 years). (Author)

Summary of ALSEP Test Loop Solvent Irradiation Testing

Energy Technology Data Exchange (ETDEWEB)

Peterman, Dean Richard [Idaho National Lab. (INL), Idaho Falls, ID (United States); Olson, Lonnie Gene [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2016-08-01

Separating the minor actinide elements (americium and curium) from the fission product lanthanides is an important step in closing the nuclear fuel cycle. Isolating the minor actinides will allow transmuting them to short lived or stable isotopes in fast reactors, thereby reducing the long-term hazard associated with these elements. The Actinide Lanthanide Separation Process (ALSEP) is being developed by the DOE-NE Material Recovery and Waste Form Development Campaign to accomplish this separation with a single process. To develop a fundamental understanding of the solvent degradation mechanisms for the ALSEP Process, testing was performed in the INL Radiolysis/Hydrolysis Test Loop for the extraction section of the ALSEP flowsheet. This work culminated in the completion of the level two milestone (M2FT-16IN030102021) "Complete ALSEP test loop solvent irradiation test.” This report summarizes the testing performed and the impact of radiation on the ALSEP Process performance as a function of dose.

The ratio of long-lived to short-lived radon-222 progeny concentrations in ground-level air

Energy Technology Data Exchange (ETDEWEB)

Hoetzl, H.; Winkler, R. [Institut fuer Strahlenschutz, GSF-Forschungszentrum fuer Umwelt und Gesundheit, Neuherberg Oberschleissheim (Germany)

1996-02-09

The ratio of {sup 210}Pb air concentration to the short-lived radon ({sup 222}Rn) decay products concentration at ground level was investigated at a semi-rural location 10 km north of Munich, south Germany, for a period of 11 years (1982-1992). The average ratio from 132 monthly mean values has been found to be (7.5{+-}2.2) x 10{sup -5} (arithmetic mean{+-}S.D.). While the time series of the short-lived radon daughter concentration exhibit a distinct seasonal pattern with maxima mostly in October of each year, the course of {sup 210}Pb air concentration is characterized by high values from October through February. Consequently, high ratios of {sup 210}Pb to short-lived decay product concentration are often observed in the winter months of December-February. To study the influence of meteorological conditions on this behaviour, {sup 210}Pb and {sup 214}Pb concentrations were measured on a short-term basis with sampling intervals of 2-3 days from October 1991 to November 1992. The air concentrations obtained within those intervals were then correlated with actual meteorological parameters. On the base of this investigation the seasonal behaviour can essentially be explained by the more frequent inversion weather conditions in winter than in the summer months. At the same location, the average ratio of {sup 210}Po to {sup 210}Pb concentration in ground level air has been found to be 0.079 from 459 weakly mean values between 1976 and 1985. Hence, the corresponding average ratios of the short-lived radon daughters (EEC) to {sup 210}Pb and {sup 210}Po, were 1:7.5x10{sup -5} and 1:0.6 x 10{sup -5}, respectively.

Applications of Radium Isotopes to Ocean Studies

Energy Technology Data Exchange (ETDEWEB)

Moore, W. S. [Department of Earth and Ocean Sciences, University of South Carolina, Columbia, SC (United States)

2013-07-15

With half-lives ranging from 3.7 days to 1600 a, naturally occurring radium isotopes have been used to study a variety of processes in the ocean. New techniques, which allow rapid analyses of the short lived isotopes, {sup 224}Ra (half-life = 3.7 days) and {sup 223}Ra (half-life = 11 days), have lead to many novel ways to apply radium to oceanography. This paper will focus on how the use of these isotopes has led to breakthroughs in quantifying: (1) the residence time of water in estuaries, (2) coastal ocean mixing rates and (3) submarine groundwater discharge (SGD). With this new understanding of rates and fluxes in the near shore environment, scientists and coastal managers are now able to evaluate sources of nutrients, carbon, and metals and their impact on the coastal ocean. For example, it is now known that SGD rivals rivers as a nutrient source to many coastal environments. (author)

Actinide colloid generation in groundwater. Part 2

International Nuclear Information System (INIS)

Kim, J.I.

1991-01-01

The progress made in the investigation of actinide colloid generation in groundwater is summarized and discussed with particular examples relevant to an understanding of the migration behaviour of actinides in natural aquifer systems. The first part deals with the characterization of colloids: groundwater colloids, actinide real-colloids and actinide pseudocolloids. The second part concentrates on the generation processes and migration behaviour of actinide pseudo colloids, which are discussed with some notable experimental examples. Importance is stressed more on the chemical aspects of the actinide colloid generation in groundwater. This work is a contribution to the CEC Mirage II project, in particular the complexation and colloids research area

Microgamma Scan System for analyzing radial isotopic profiles of irradiated transmutation fuels

International Nuclear Information System (INIS)

Hilton, Bruce A.; McGrath, Christopher A.

2008-01-01

The U. S. Global Nuclear Energy Partnership / Advanced Fuel Cycle Initiative (GNEP/AFCI) is developing metallic transmutation alloys as a fuel form to transmute the long-lived transuranic actinide isotopes contained in spent nuclear fuel into shorter-lived fission products. A micro-gamma scan system is being developed to analyze the radial distribution of fission products, such as Cs-137, Cs-134, Ru-106, and Zr-95, in irradiated fuel cross-sections. The micro-gamma scan system consists of a precision linear stage with integrated sample holder and a tungsten alloy collimator, which interfaces with the Idaho National Laboratory (INL) Analytical Laboratory Hot Cell (ALHC) Gamma Scan System high purity germanium detector, multichannel analyzer, and removable collimators. A simplified model of the micro-gamma scan system was developed in MCNP (Monte-Carlo N-Particle Transport Code) and used to investigate the system performance and to interpret data from the scoping studies. Preliminary measurements of the micro-gamma scan system are discussed. (authors)

Standard test method for analysis of total and isotopic uranium and total thorium in soils by inductively coupled plasma-mass spectrometry

CERN Document Server

American Society for Testing and Materials. Philadelphia

2008-01-01

1.1 This test method covers the measurement of total uranium (U) and thorium (Th) concentrations in soils, as well as the determination of the isotopic weight percentages of 234U, 235U, 236U, and 238U, thereby allowing for the calculation of individual isotopic uranium activity or total uranium activity. This inductively coupled plasma-mass spectroscopy (ICP-MS) method is intended as an alternative analysis to methods such as alpha spectroscopy or thermal ionization mass spectroscopy (TIMS). Also, while this test method covers only those isotopes listed above, the instrumental technique may be expanded to cover other long-lived radioisotopes since the preparation technique includes the preconcentration of the actinide series of elements. The resultant sample volume can be further reduced for introduction into the ICP-MS via an electrothermal vaporization (ETV) unit or other sample introduction device, even though the standard peristaltic pump introduction is applied for this test method. The sample preparatio...

Transmutation of minor actinides in a spherical torus tokamak fusion reactor, FDTR

International Nuclear Information System (INIS)

Feng, K.M.; Zhang, G.S.; Deng, M.G.

2003-01-01

In this paper, a concept for the transmutation of minor actinide (MA) nuclear wastes based on a spherical torus (ST) tokamak reactor, FDTR, is put forward. A set of plasma parameters suitable for the transmutation blanket was chosen. The 2-D neutron transport code TWODANT, the 3-D Monte Carlo code MCNP/4B, the 1-D neutron transport and burn-up calculation code BISON3.0 and their associated data libraries were used to calculate the transmutation rate, the energy multiplication factor and the tritium breeding ratio of the transmutation blanket. The calculation results for the system parameters and the actinide series isotopes for different operation times are presented. The engineering feasibility of the center-post (CP) of FDTR has been investigated and the results are also given. A preliminary neutronics calculation based on an ST transmutation blanket shows that the proposed system has a high transmutation capability for MA wastes. (author)

Actinide cation-cation complexes

International Nuclear Information System (INIS)

Stoyer, N.J.; Seaborg, G.T.

1994-12-01

The +5 oxidation state of U, Np, Pu, and Am is a linear dioxo cation (AnO 2 + ) with a formal charge of +1. These cations form complexes with a variety of other cations, including actinide cations. Other oxidation states of actinides do not form these cation-cation complexes with any cation other than AnO 2 + ; therefore, cation-cation complexes indicate something unique about AnO 2 + cations compared to actinide cations in general. The first cation-cation complex, NpO 2 + ·UO 2 2+ , was reported by Sullivan, Hindman, and Zielen in 1961. Of the four actinides that form AnO 2 + species, the cation-cation complexes of NpO 2 + have been studied most extensively while the other actinides have not. The only PuO 2 + cation-cation complexes that have been studied are with Fe 3+ and Cr 3+ and neither one has had its equilibrium constant measured. Actinides have small molar absorptivities and cation-cation complexes have small equilibrium constants; therefore, to overcome these obstacles a sensitive technique is required. Spectroscopic techniques are used most often to study cation-cation complexes. Laser-Induced Photacoustic Spectroscopy equilibrium constants for the complexes NpO 2 + ·UO 2 2+ , NpO 2 + ·Th 4+ , PuO 2 + ·UO 2 2+ , and PuO 2 + ·Th 4+ at an ionic strength of 6 M using LIPAS are 2.4 ± 0.2, 1.8 ± 0.9, 2.2 ± 1.5, and ∼0.8 M -1

Subcritical limits for special fissile actinides

International Nuclear Information System (INIS)

Clark, H.K.

1980-01-01

Critical masses and subcritical mass limits in oxide-water mixtures were calculated for actinide nuclides other than 233 U, 235 U, and 239 Pu that have an odd number of neutrons in the nucleus: S/sub n/ transport theory was used together with cross sections, drawn from the GLASS multigroup library, developed to provide accurate forecasts of actinide production at Savannah River. The subcritical limits are 201 g for 241 Pu, 13 g for 242 /sup m/Am, 90 g for 243 Cm, 30 g for 245 Cm, 900 g for 247 Cm, 10 g for 249 Cf, and 5 g for 251 Cf. Association of 241 Pu with an equal mass of 240 Pu increases the 241 Pu limit to a value greater than that for pure 239 Pu. Association of 242 /sup m/Am with 241 Am increases the limit for the mixture to that for dry, theoretical density AmO 2 at isotopic concentrations of 242 /sup m/Am less than approx. 6%. Association of 245 Cm with 244 Cm increases the limit according to the formula 30 + 0.3 244 Cm/ 245 Cm up to the limit for dry CmO 2 . A limiting mass of 8.15 kg for plutonium containing at least 67% 238 Pu as oxide was calculated that applies (provided 240 Pu exceeds 241 Pu) with no limit on moderation. 1 figure, 5 tables

Performance comparison of metallic, actinide burning fuel in lead-bismuth and sodium cooled fast reactors

International Nuclear Information System (INIS)

Weaver, K.D.; Herring, J.S.; Macdonald, P.E.

2001-01-01

Various methods have been proposed to ''incinerate'' or ''transmute'' the current inventory of transuranic waste (TRU) that exits in spent light-water-reactor (LWR) fuel, and weapons plutonium. These methods include both critical (e.g., fast reactors) and non-critical (e.g., accelerator transmutation) systems. The work discussed here is part of a larger effort at the Idaho National Engineering and Environmental Laboratory (INEEL) and at the Massachusetts Institute of Technology (MIT) to investigate the suitability of lead and lead-alloy cooled fast reactors for producing low-cost electricity as well as for actinide burning. The neutronics of non fertile fuel loaded with 20 or 30-wt% light water reactor (LWR) plutonium plus minor actinides for use in a lead-bismuth cooled fast reactor are discussed in this paper, with an emphasis on the fuel cycle life and isotopic content. Calculations show that the average actinide burn rate is similar for both the sodium and lead-bismuth cooled cases ranging from -1.02 to -1.16 g/MWd, compared to a typical LWR actinide generation rate of 0.303 g/MWd. However, when using the same parameters, the sodium-cooled case went subcritical after 0.2 to 0.8 effective full power years, and the lead-bismuth cooled case ranged from 1.5 to 4.5 effective full power years. (author)

Extraction chromatogrpahy of actinides, ch. 7

International Nuclear Information System (INIS)

Mueller, W.

1975-01-01

This review on extraction chromatography of actinides emphasizes the important usage of neutral (Tributylphosphate), basic (substituted ammonium salts), and acidic (HDEHP) extractants, and their application to separations of actinides in the di-to hexavalent oxidation state. Furthermore, the actinide extraction by ketones, ethers, alcohols and β-diketones is discussed

Actinides and fission products partitioning from high level liquid waste

International Nuclear Information System (INIS)

Yamaura, Mitiko

1999-01-01

The presence of small amount of mixed actinides and long-lived heat generators fission products as 137 Cs and 90 Sr are the major problems for safety handling and disposal of high level nuclear wastes. In this work, actinides and fission products partitioning process, as an alternative process for waste treatment is proposed. First of all, ammonium phosphotungstate (PWA), a selective inorganic exchanger for cesium separation was chosen and a new procedure for synthesizing PWA into the organic resin was developed. An strong anionic resin loaded with tungstate or phosphotungstate anion enables the precipitation of PWA directly in the resinous structure by adding the ammonium nitrate in acid medium (R-PWA). Parameters as W/P ratio, pH, reactants, temperature and aging were studied. The R-PWA obtained by using phosphotungstate solution prepared with W/P=9.6, 9 hours digestion time at 94-106 deg C and 4 to 5 months aging time showed the best capacity for cesium retention. On the other hand, Sr separation was performed by technique of extraction chromatography, using DH18C6 impregnated on XAD7 resin as stationary phase. Sr is selectively extracted from acid solution and >99% was recovered from loaded column using distilled water as eluent. Concerning to actinides separations, two extraction chromatographic columns were used. In the first one, TBP(XAD7) column, U and Pu were extracted and its separations were carried-out using HNO 3 and hydroxylamine nitrate + HNO 3 as eluent. In the second one, CMP0-TBP(XAD7) column, the actinides were retained on the column and the separations were done by using (NH 4 ) 2 C 2 O 4 , DTPA, HNO 3 and HCl as eluent. The behavior of some fission products were also verified in both columns. Based on the obtained data, actinides and fission products Cs and Sr partitioning process, using TBP(XAD7) and CMP0-TBP(XAD7) columns for actinides separation, R-PWA column for cesium retention and DH18C6(XAD7) column for Sr isolation was performed

Few atom chemistry of the trans actinide element rutherfordium (Rf)

International Nuclear Information System (INIS)

Nagame, Y.

2002-01-01

Studies of chemical properties of the trans actinide elements - starting with element 104 (Rf) - offer the unique opportunity to obtain information about trends in the Periodic Table at the limits of nuclear stability and to assess the magnitude of the influence of relativistic effects on chemical properties. To explore experimentally the influence of relativistic effects of electron shell structure, we study the chemical properties of the trans actinide elements. So far, we have developed some experimental apparatuses for the study of chemical properties of the trans actinide elements: a beam-line safety system for the usage of the gas-jet coupled radioactive 248 Cm target chamber for the production of trans actinides, a rotating wheel catcher apparatus for the measurement of α particles and spontaneous fission decay of trans actinides and an automated rapid chemical separation apparatus based on high performance liquid chromatography. The trans actinide nuclide, the element 104, 261 Rf (t 1/2 = 78 s) has been successfully produced via the reactions of 248 Cm( 18 O,5n) at the JAERI (Japan Atomic Energy Research Institute) tandem accelerator. The evaluated production cross section was about 10 nb, indicating that the production rate was approximately 2 atoms per min. Because of the short half-life and the low production rate of Rf, each atom produced decays before a new atom is synthesized. It means that any chemistry to be performed must be done on an 'atom-at-a-time' basis. Therefore rapid, very efficient and selective chemical procedures are indispensable to isolate the desired trans actinide 261 Rf. To perform fast and repetitive ion-exchange separation of Rf, we have developed the apparatus AIDA (Automated Ion exchange separation system coupled with the Detection apparatus for Alpha spectroscopy). Recently, ion-exchange behavior of Rf in acidic solutions has been studied with AIDA, and the results indicate that anion-exchange behavior of Rf is quite similar

Theoretical studies on the alpha α decay half-lives of hyper and normal isotopes of Po

Science.gov (United States)

Santhosh, K. P.; Nithya, C.

2018-03-01

The α decay half-lives of hyper and normal isotopes of Po nuclei are studied in the present work. The inclusion of Λ - N interaction changes the half-life for α decay. The theoretical predictions on the α decay half-lives of normal Po isotopes are compared with experimental results and are seen to be matching well with each other. The neutron shell closure at N = 126 is found to be the same for both normal and hypernuclei. The Geiger-Nuttal (G-N) law for α decay is unaltered in the case of hypernuclei. The hypernuclei will decay into normal nuclei by mesonic or non-mesonic decay modes. Since the half-lives of normal Po nuclei are well within the experimental limits, our theoretical results suggest experimental verification of the α emission from hyper Po nuclei in a cascade process.

Minor actinide transmutation on PWR burnable poison rods

International Nuclear Information System (INIS)

Hu, Wenchao; Liu, Bin; Ouyang, Xiaoping; Tu, Jing; Liu, Fang; Huang, Liming; Fu, Juan; Meng, Haiyan

2015-01-01

Highlights: • Key issues associated with MA transmutation are the appropriate loading pattern. • Commercial PWRs are the only choice to transmute MAs in large scale currently. • Considerable amount of MA can be loaded to PWR without disturbing k eff markedly. • Loading MA to PWR burnable poison rods for transmutation is an optimal loading pattern. - Abstract: Minor actinides are the primary contributors to long term radiotoxicity in spent fuel. The majority of commercial reactors in operation in the world are PWRs, so to study the minor actinide transmutation characteristics in the PWRs and ultimately realize the successful minor actinide transmutation in PWRs are crucial problem in the area of the nuclear waste disposal. The key issues associated with the minor actinide transmutation are the appropriate loading patterns when introducing minor actinides to the PWR core. We study two different minor actinide transmutation materials loading patterns on the PWR burnable poison rods, one is to coat a thin layer of minor actinide in the water gap between the zircaloy cladding and the stainless steel which is filled with water, another one is that minor actinides substitute for burnable poison directly within burnable poison rods. Simulation calculation indicates that the two loading patterns can load approximately equivalent to 5–6 PWR annual minor actinide yields without disturbing the PWR k eff markedly. The PWR k eff can return criticality again by slightly reducing the boric acid concentration in the coolant of PWR or removing some burnable poison rods without coating the minor actinide transmutation materials from PWR core. In other words, loading minor actinide transmutation material to PWR does not consume extra neutron, minor actinide just consumes the neutrons which absorbed by the removed control poisons. Both minor actinide loading patterns are technically feasible; most importantly do not need to modify the configuration of the PWR core and

Ability of Accelerator-Driven Systems (ADS) to Transmute Long Lived Fission Fragments

International Nuclear Information System (INIS)

Nguyen Mong Giao; Nguyen Thi Ai Thu; Tu Thanh Danh; Tran Thanh Dung; Huynh, Thi Kim Chi

2010-12-01

This paper presents the research results of the possibility to transmute the long-lived radioactive isotopes into stable or short-lived, mainly the long-lived fission fragments as 99 Tc, 127 I, 129 I, 181 Ta, 107 Ag, 109 Ag by accelerator-driven systems. We use semi-empirical formulas to establish our calculating code with the support of computer programs. (author)

Increased Concentrations of Short-Lived Decay-Series Radionuclides in Groundwaters Underneath the Nopal I Uranium Deposit at Pena Blanca, Mexico

Science.gov (United States)

Luo, S.; Ku, T.; Todd, V.; Murrell, M. T.; Dinsmoor, J. C.

2007-05-01

The Nopal I uranium ore deposit at Pena Blanca, Mexico, located at > 200 meters above the groundwater table, provides an ideal natural analog for quantifying the effectiveness of geological barrier for isolation of radioactive waste nuclides from reaching the human environments through ground water transport. To fulfill such natural analog studies, three wells (PB1, PB2, and PB3 respectively) were drilled at the site from the land surface down to the saturated groundwater zone and ground waters were collected from each of these wells through large- volume sampling/in-situ Mn-filter filtration for analyses of short-lived uranium/thorium-series radionuclides. Our measurements from PB1 show that the groundwater standing in the hole has much lower 222Rn activity than the freshly pumped groundwater. From this change in 222Rn activity, we estimate the residence time of groundwater in PB1 to be about 20 days. Our measurements also show that the activities of short-lived radioisotopes of Th (234Th), Ra (228Ra, 224Ra, 223Ra), Rn (222Rn), Pb (210Pb), and Po (210Po) in PB1, PB2, and PB3 are all significantly higher than those from the other wells near the Nopal I site. These high activities provide evidence for the enrichment of long-lived U and Ra isotopes in the groundwater as well as in the associated adsorbed phases on the fractured aquifer rocks underneath the ore deposit. Such enrichment suggests a rapid dissolution of U and Ra isotopes from the uranium ore deposit in the vadose zone and the subsequent migration to the groundwater underneath. A reactive transport model can be established to characterize the in-situ transport of radionuclides at the site. The observed change of 222Rn activity at PB1 also suggests that the measured high radioactivityies in ground waters from the site isare not an artifact of drilling operations. However, further studies are needed to assess if or to what extent the radionuclide migration is affected by the previous mining activities at

Soot and short-lived pollutants provide political opportunity

Science.gov (United States)

Victor, David G.; Zaelke, Durwood; Ramanathan, Veerabhadran

2015-09-01

Cutting levels of soot and other short-lived pollutants delivers tangible benefits and helps governments to build confidence that collective action on climate change is feasible. After the Paris climate meeting this December, actually reducing these pollutants will be essential to the credibility of the diplomatic process.

Actinide speciation in the environment

International Nuclear Information System (INIS)

Choppin, G.R.

2007-01-01

Nuclear test explosions and nuclear reactor wastes and accidents have released large amounts of radioactivity into the environment. Actinide ions in waters often are not in a state of thermodynamic equilibrium and their solubility and migration behavior is related to the form in which the nuclides are introduced into the aquatic system. Chemical speciation, oxidation state, redox reactions, and sorption characteristics are necessary in predicting solubility of the different actinides, their migration behaviors and their potential effects on marine biota. The most significant of these variables is the oxidation state of the metal ion as the simultaneous presence of more than one oxidation state for some actinides in a solution complicates actinide environmental behavior. Both Np(V)O 2 + and Pu(V)O 2 + , the most significant soluble states in natural oxic waters, are relatively noncomplexing and resistant to hydrolysis and subsequent precipitation. The solubility of NpO 2 + can be as high as 10 -4 M while that of PuO 2 + is much more limited by reduction to the insoluble tetravalent species, Pu(OH) 4 , (pK sp ≥56) but which can be present in the pentavalent form in aqautic phases as colloidal material. The solubility of hexavalent UO 2 2+ in sea water is relatively high due to formation of carbonate complexes. The insoluble trivalent americium hydroxocarbonate, Am(OH)(CO 3 ) is the limiting species for the solubility of Am(III) in sea water. Thorium(IV) is present as Th(OH) 4 , in colloidal form. The chemistry of actinide ions in the environment is reviewed to show the spectrum of reactions that can occur in natural waters which must be considered in assessing the environmental behavior of actinides. Much is understood about sorption of actinides on surfaces, the mode of migration of actinides in such waters and the potential effects of these radioactive species on marine biota, but much more understanding of the behavior of the actinides in the environment is

Carbon isotopic fractionation in live benthic foraminifera -comparison with inorganic precipitate studies

Energy Technology Data Exchange (ETDEWEB)

Grossmann, E L [University of Southern California, Los Angeles (USA). Dept. of Geological Sciences

1984-07-01

Carbon and oxygen isotopic analyses have been performed on live-stained aragonitic and calcitic benthic foraminifera and dissolved inorganic carbon from the Southern California Borderland to examine carbon isotopic fractionation in foraminifera. Temperature, salinity and pH data have also been collected to permit accurate determination of the delta/sup 13/C of bicarbonate ion and thus aragonite-HCO/sub 3//sup -/ and calcite-HCO/sub 3//sup -/ isotopic enrichment factors (epsilonsub(ar-b) and epsilonsub(cl-b), respectively). Only species which precipitate in /sup 18/O equilibrium have been considered. epsilonsub (ar-b) values based on Hoeglundina elegans range from 1.9 per mille at 2.7 deg C to 1.1 per mille at 9.5 deg C. The temperature dependence of epsilonsub(ar-b) is considerably greater than the equilibrium equation would predict and may be due to a vital effect. The calcitic foraminifera Cassidulina tortuosa, Cassidulina braziliensis, and Cassidulina limbata, Bank and Terrace dwellers, have s

Status of the French research programme for actinides and fission products partitioning and transmutation

International Nuclear Information System (INIS)

Warin, D.

2003-01-01

The paper focus on separation and transmutation research and development programme and main results over these ten last years. The massive research programme on enhanced separation, conducted by CEA and supported by broad international cooperation, has recently achieved some vital progress. Based on real solutions derived from the La Hague process, the CEA demonstrated the lab-scale feasibility of extracting minor actinides and some fission products (I, Cs and Tc) using an hydrometallurgical process that can be extrapolated on the industrial scale. The CEA also conducted programmes proving the technical feasibility of the elimination of minor actinides and fission products by transmutation: fabrication of specific targets and fuels for transmutation tests in the HFR and Phenix reactors, neutronics and technology studies for ADS developments in order to support the MEGAPIE, TRADE and MYRRHA experiments and the future 100 MW international ADS demonstrator. Scenarios studies aimed at stabilizing the inventory with long-lived radionuclides, plutonium, minor actinides and certain long-lived fission products in different nuclear power plant parks and to verify the feasibility at the level of the cycle facilities and fuels involved in those scenarios. Three French Research Groups CEA-CNRS carry out partitioning (PRACTIS) and transmutation (NOMADE and GEDEON) more basic studies. (author)

Report on the IAEA coordinated research program on the measurement and evaluation of transactinium isotope nuclear decay data

International Nuclear Information System (INIS)

Reich, C.W.

1979-01-01

As one result of the First IAEA Advisory Group Meeting on Transactinium Isotope Nuclear Data, held in November 1975 at Karlsruhe, an IAEA Coordinated Research Program was set up to address certain identified actinide-isotope decay-data needs in reactor technology. At present, laboratories from five nations are involved in this effort. This paper gives an overview of this program, including its origin and the present status of the measurements being carried out. The current status of the actinide-nuclide half-life, spontaneous-fission branching ratio, α-intensity and γ-intensity data of concern to the Coordinated Research Program is presented and briefly discussed. 3 figures, 9 tables

Applications of short lived nuclides in activation analysis, problems and progress

Energy Technology Data Exchange (ETDEWEB)

Grass, F [Atominstitut, Vienna (Austria)

1976-07-01

Short lived nuclides or isomeric transitions, respectively would have some advantages over long lived ones. Although we published a paper concerning a germanium-determination in iron meteorites some years ago, only few laboratories use this technique, the main reason being that the high matrix activity disturbs the measurement of energy-spectra. A multichannel analyzer in the time sequence mode enables Li-8 determination by a purely instrumental method which is therefore used more frequently. In the time sequence mode much higher counting rates up to 10 - 50 MHz are processed then by taking energy-spectra. This is the reason why activation analysis with short lived isomeric states is seldom applied when counting rate and pulse height are to be detected simultaneously. Exceptional difficulties are encountered in measurement of samples activated by a reactor pulse. Further difficulties arise from the fact that an optimal expelling time depends on the half life of the nuclide, and is more critical if the half life is short and the full width half maximum of the reactor pulse is small. Commercial Ge-Li-detectors can be used only at low counting rates, so that samples with high matrix activities cannot be measured. Modifying the electronic system enables registration of samples with high matrix activities. For short lived nuclides emitting hard beta-rays, e.g. B-12 or Li-8, a Cerenkov-detector is optimal. These problems are discussed in examples. (author)

Thermal ionization mass spectrometry (TIMS) of actinides: Pushing the limits of accuracy and detection

Energy Technology Data Exchange (ETDEWEB)

Buerger, Stefan; Boulyga, Sergei; Cunningham, Alan; Klose, Dilani; Koepf, Andreas; Poths, Jane [Safeguards Analytical Laboratory, International Atomic Energy Agency, Vienna (Austria); Richter, Stephan [Institute for Reference Materials and Measurements, JRC-EU, Geel (Belgium)

2010-07-01

New method developments in multi-collector thermal ionization mass spectrometry (MC-TIMS) for actinide isotope ratio analysis to improve accuracy and limits of detection will be presented. With respect to limits of detection, results on improving work function using various carbon additives will be reviewed and presented as well as developments in cavity ion source (as compared to standard flat ribbon filament ion source) for femto- and attogram levels of uranium, plutonium, and americium. With respect to accuracy, results on isotope ratio measurements of isotopes of uranium (relative accuracy of 0.3% to 0.01%) are presented with an example being U-234-Th-230 age-dating (NBL CRM 112-A). In this context, the importance of traceability (to the S.I. units) and the use of (certified) reference materials are emphasized. The focus of this presentation is on applications to nuclear safeguards / forensics.

Denaturing of plutonium by transmutation of minor-actinides for enhancement of proliferation resistance

International Nuclear Information System (INIS)

Sagara, Hiroshi; Saito, Masaki; Peryoga, Yoga; Ezoubtchenko, Alexey; Takivayev, Alan

2005-01-01

Feasibility study for the plutonium denaturing by utilizing minor-actinide transmutation in light water reactors has been performed. And the intrinsic feature of proliferation resistance of plutonium has been discussed based on IAEA's publication and Kessler's proposal. The analytical results show that not only 238 Pu but also other plutonium isotopes with even-mass-number have very important role for denaturing of plutonium due to their relatively large critical mass and noticeably high spontaneous fission neutron generation. With the change of the minor-actinide doping ratio in U-Pu mix oxide fuel and moderator to fuel ratio, it is found that the reactor-grade plutonium from conventional light water reactors can be denatured to satisfy the proliferation resistance criterion based on the Kessler's proposal but not to be sufficient for the criterion based on IAEA's publication. It has been also confirmed that all the safety coefficients take negative value throughout the irradiation. (author)

Fast Resonance Raman Spectroscopy of Short-Lived Radicals

DEFF Research Database (Denmark)

Pagsberg, Palle Bjørn; Wilbrandt, Robert Walter; Hansen, Karina Benthin

1976-01-01

We report the first application of pulsed resonance Raman spectroscopy to the study of short-lived free radicals produced by pulse radiolysis. A single pulse from a flash-lamp pumped tunable dye laser is used to excite the resonance Raman spectrum of the p-terphenyl anion radical with an initial...

Use of high gradient magnetic separation for actinide application

International Nuclear Information System (INIS)

Avens, L.R.; Worl, L.A.; Padilla, D.D.

1996-01-01

Decontamination of materials such as soils or waste water that contain radioactive isotopes, heavy metals, or hazardous components is a subject of great interest. Magnetic separation is a physical separation process that segregates materials on the basis of magnetic susceptibility. Because the process relies on physical properties, separations can be achieved while producing a minimum of secondary waste. Most traditional physical separation processes effectively treat particles larger than 70 microns. In many situations, the radioactive contaminants are found concentrated in the fine particle size fraction of less than 20 microns. For effective decontamination of the fine particle size fraction most current operations resort to chemical dissolution methods for treatment. High gradient magnetic separation (HGMS) is able to effectively treat particles from 90 to ∼0.1 micron in diameter. The technology is currently used on the 60 ton per hour scale in the kaolin clay industry. When the field gradient is of sufficiently high intensity, paramagnetic particles can be physically captured and separated from extraneous nonmagnetic material. Because all actinide compounds are paramagnetic, magnetic separation of actinide containing mixtures is feasible. The advent of reliable superconducting magnets also makes magnetic separation of weakly paramagnetic species attractive. HGMS work at Los Alamos National Laboratory (LANL) is being developed for soil remediation, waste water treatment and treatment of actinide chemical processing residues. LANL and Lockheed Environmental Systems and Technologies Company (LESAT) have worked on a co-operative research and development agreement (CRADA) to develop HGMS for radioactive soil decontamination. The program is designed to transfer HGMS from the laboratory and other industries for the commercial treatment of radioactive contaminated materials. 9 refs., 2 figs., 2 tabs

Burning actinides in very hard spectrum reactors

International Nuclear Information System (INIS)

Robinson, A.H.; Shirley, G.W.; Prichard, A.W.; Trapp, T.J.

1978-01-01

The major unresolved problem in the nuclear industry is the ultimate disposition of the waste products of light water reactors. The study demonstrates the feasibility of designing a very hard spectrum actinide burner reactor (ABR). A 1100 MW/sub t/ ABR design fueled entirely with actinides reprocessed from light water reactor (LWR) wastes is proposed as both an ultimate disposal mechanism for actinides and a means of concurrently producing usable power. Actinides from discharged ABR fuel are recycled to the ABR while fission products are routed to a permanent repository. As an integral part of a large energy park, each such ABR would dispose of the waste actinides from 2 LWRs

Recent activities for β-decay half-lives and β-delayed neutron emission of very neutron-rich isotopes

Energy Technology Data Exchange (ETDEWEB)

Dillmann, Iris [TRIUMF, Vancouver BC, V6T 2A3, Canada and GSI Helmholtzzentrum für Schwerionenforschung GmbH, D-64291 Darmstadt (Germany); Abriola, Daniel [Laboratorio Tandar, Comisión Nacional de Energía Atómica, B1650KINA, San Martín, Buenos Aires (Argentina); Singh, Balraj [Department of Physics and Astronomy, McMaster University, Hamilton ON, L8S 4M1 (Canada)

2014-05-02

Beta-delayed neutron (βn) emitters play an important, two-fold role in the stellar nucleosynthesis of heavy elements in the 'rapid neutron-capture process' (r process). On one hand they lead to a detour of the material β-decaying back to stability. On the other hand, the released neutrons increase the neutron-to-seed ratio, and are re-captured during the freeze-out phase and thus influence the final solar r-abundance curve. A large fraction of the isotopes inside the r-process reaction path are not yet experimentally accessible and are located in the (experimental) 'Terra Incognita'. With the next generation of fragmentation and ISOL facilities presently being built or already in operation, one of the main motivation of all projects is the investigation of these very neutron-rich isotopes. A short overview of one of the planned programs to measure βn-emitters at the limits of the presently know isotopes, the BRIKEN campaign (Beta delayed neutron emission measurements at RIKEN) will be given. Presently, about 600 β-delayed one-neutron emitters are accessible, but only for a third of them experimental data are available. Reaching more neutron-rich isotopes means also that multiple neutron-emission becomes the dominant decay mechanism. About 460 β-delayed two-, three-or four-neutron emitters are identified up to now but for only 30 of them experimental data about the neutron branching ratios are available, most of them in the light mass region below A=30. The International Atomic and Energy Agency (IAEA) has identified the urgency and picked up this topic recently in a 'Coordinated Research Project' on a 'Reference Database for Beta-Delayed Neutron Emission Data'. This project will review, compile, and evaluate the existing data for neutron-branching ratios and half-lives of β-delayed neutron emitters and help to ensure a reliable database for the future discoveries of new isotopes and help to constrain astrophysical and

Actinide separative chemistry

International Nuclear Information System (INIS)

Boullis, B.

2004-01-01

Actinide separative chemistry has focused very heavy work during the last decades. The main was nuclear spent fuel reprocessing: solvent extraction processes appeared quickly a suitable, an efficient way to recover major actinides (uranium and plutonium), and an extensive research, concerning both process chemistry and chemical engineering technologies, allowed the industrial development in this field. We can observe for about half a century a succession of Purex plants which, if based on the same initial discovery (i.e. the outstanding properties of a molecule, the famous TBP), present huge improvements at each step, for a large part due to an increased mastery of the mechanisms involved. And actinide separation should still focus R and D in the near future: there is a real, an important need for this, even if reprocessing may appear as a mature industry. We can present three main reasons for this. First, actinide recycling appear as a key-issue for future nuclear fuel cycles, both for waste management optimization and for conservation of natural resource; and the need concerns not only major actinide but also so-called minor ones, thus enlarging the scope of the investigation. Second, extraction processes are not well mastered at microscopic scale: there is a real, great lack in fundamental knowledge, useful or even necessary for process optimization (for instance, how to design the best extracting molecule, taken into account the several notifications and constraints, from selectivity to radiolytic resistivity?); and such a need for a real optimization is to be more accurate with the search of always cheaper, cleaner processes. And then, there is room too for exploratory research, on new concepts-perhaps for processing quite new fuels- which could appear attractive and justify further developments to be properly assessed: pyro-processes first, but also others, like chemistry in 'extreme' or 'unusual' conditions (supercritical solvents, sono-chemistry, could be

Actinides integral measurements on FCA assemblies

International Nuclear Information System (INIS)

Mukaiyama, Takehiko; Okajima, Shigeaki

1984-01-01

Actinide integral measurements were performed on eight assemblies of FCA where neutron energy spectra were shifted systematically from soft to hard in order to evaluate and modify the nuclear cross section data of major actinides. Experimental values on actinide fission rates and sample reactivity worths are compared with the calculated values using JENDL-2 and ENDF/B-V (or IV) data sets. (author)

Study of five-dimensional potential-energy surfaces for actinide isotopes by the macroscopic-microscopic method

Science.gov (United States)

Fan, T. S.; Wang, Z. M.; Zhu, X.; Zhu, W. J.; Zhong, C. L.

2017-09-01

In this work, the nuclear potential-energy of the deformed nuclei as a function of shape coordinates is calculated in a five-dimensional (5D) parameter space of the axially symmetric generalized Lawrence shapes, on the basis of the macroscopic-microscopic method. The liquid-drop part of the nuclear energy is calculated according to the Myers-Swiatecki model and the Lublin-Strasbourg-drop (LSD) formula. The Woods-Saxon and the folded-Yukawa potentials for deformed nuclei are used for the shell and pairing corrections of the Strutinsky-type. The pairing corrections are calculated at zero temperature, T, related to the excitation energy. The eigenvalues of Hamiltonians for protons and neutrons are found by expanding the eigen-functions in terms of harmonic-oscillator wave functions of a spheroid. Then the BCS pair is applied on the smeared-out single-particle spectrum. By comparing the results obtained by different models, the most favorable combination of the macroscopic-microscopic model is known as the LSD formula with the folded-Yukawa potential. Potential-energy landscapes for actinide isotopes are investigated based on a grid of more than 4,000,000 deformation points and the heights of static fission barriers are obtained in terms of a double-humped structure on the full 5D parameter space. In order to locate the ground state shapes, saddle points, scission points and optimal fission path on the calculated 5D potential-energy surface, the falling rain algorithm and immersion method are designed and implemented. The comparison of our results with available experimental data and others' theoretical results confirms the reliability of our calculations.

LLNL SFA OBER SBR FY17 Program Management and Performance Report: Subsurface Biogeochemistry of Actinides

Energy Technology Data Exchange (ETDEWEB)

Kersting, Annie B. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-06-23

A major scientific challenge in environmental sciences is to identify the dominant processes controlling actinide transport in the environment. It is estimated that currently, over 2200 metric tons of anthropogenic plutonium (Pu) has accumulated worldwide, a number that increases yearly with additional spent nuclear fuel (Ewing et al., 2010). Plutonium has been shown to migrate on the scale of kilometers, giving way to a critical concern that the fundamental biogeochemical processes that control its behavior in the subsurface are not well understood (Kersting et al. 1999; Novikov et al. 2006; Santschi et al. 2002). Neptunium (Np) is less prevalent in the environment; however, it is predicted to be a significant long-term dose contributor in high-level nuclear waste. Our focus on Np chemistry in this Science Plan is intended to help formulate a better understanding of Pu redox transformations in the environment and clarify the differences between the two long-lived actinides. The research approach of our Science Plan combines (1) Fundamental Mechanistic Studies that identify and quantify biogeochemical processes that control actinide behavior in solution and on solids, (2) Field Integration Studies that investigate the transport characteristics of Pu and test our conceptual understanding of actinide transport, and (3) Actinide Research Capabilities that allow us to achieve the objectives of this Scientific Focus Area (SFA) and provide new opportunities for advancing actinide environmental chemistry. These three Research Thrusts form the basis of our SFA Science Program.

Radiochemical search for neutron-rich isotopes of element 107

International Nuclear Information System (INIS)

Schaedel, M.

1987-01-01

Recent mass calculations have indicated that there is a region of deformed nuclei around neutron number N=162 that is especially stable against spontaneous fission. Barrier heights of about 5 MeV for Z = 107 nuclides can be extrapolated. To search for new, neutron-rich isotopes of element 107 in radiochemical experiments with 254 Es as a target an on-line chemical separation of element 107 (EKA-Rhenium), especially from the actinide elements is needed. An on-line gas-phase chemistry was developed with the homolog Re based on the volatility of the oxide which is transported in an O 2 containing atmosphere along a temperature gradient in a quartz tube and is condensed onto a thin Ta coated Ni-foil. The authors applied this technique in two series of experiments with their rotating wheel on-line gas-phase chemistry apparatus at the 88-inch cyclotron where they irradiated 254 Es as a target with 93 MeV and 96 MeV 16 O ions to search for 266 107. The assignment of the observed alpha events between 8 and 9 MeV to possibly (1) non actinide contaminants like 212 Po, (2) known isotopes of heavy elements like 261 105, or (3) a new isotope will be discussed

The ISOLDE experimental hall, wth the isotope separator in the upper left corner.

CERN Multimedia

CERN PhotoLab

1969-01-01

Beam tubes branch out from a switchyard, which by electrostatic deflectors direct beams of short-lived isotopes to various spectroscopic equipment. From left to right, Rudi Stoeckli at the separator control panel, Gilbert Droz and Henri Bersinger.

Production of Cs and Fr isotopes from a high-density UC targets with different grain dimensions

Energy Technology Data Exchange (ETDEWEB)

Panteleev, V.N.; Barzakh, A.E.; Fedorov, D.V.; Ivanov, V.S.; Mezilev, K.A.; Molkanov, P.L.; Moroz, F.V.; Orlov, S.Yu.; Volkov, Yu.M. [Petersburg Nuclear Physics Institute RAS, Gatchina (Russian Federation); Alyakrinskiy, O.; Barbui, M.; Stroe, L.; Tecchio, L.B.; Tonezzer, M. [Laboratori Nationali di Legnaro, Legnaro (Padova) (Italy); Lhersonneau, G. [GANIL, Caen Cedex 5 (France)

2009-12-15

A UC target material of 11.3{+-}0.5 g/cm{sup 3} uranium density with the grain size of 20 and 5{mu}m manufactured in a form of pills by the method of powder metallurgy has been tested on-line within the temperature range of 1800-2100 C. The mass of uranium exposed to the beam was 4-7g. The yields and release rates of Cs and Fr isotopes produced by fission and spallation reactions of {sup 238}U by 1GeV protons have been measured. The yields of Cs and Fr isotopes obtained from the tested target materials have been compared, including yields of very short-lived Fr isotopes with half-lives down to 1ms. Temperature-resistant materials (porous graphite and tantalum foil) have been used for the internal-container construction, which holds the UC target pills inside a tungsten external container heated by the resistant heating. The fastest release and the highest efficiency for short-lived isotopes have been obtained for the targets with the internal container manufactured from the tantalum foil. Results of on-line tests of a big mass target (730g of 5{mu}m grain UC target material) have been discussed. (orig.)

Production of Cs and Fr isotopes from a high-density UC targets with different grain dimensions

International Nuclear Information System (INIS)

Panteleev, V.N.; Barzakh, A.E.; Fedorov, D.V.; Ivanov, V.S.; Mezilev, K.A.; Molkanov, P.L.; Moroz, F.V.; Orlov, S.Yu.; Volkov, Yu.M.; Alyakrinskiy, O.; Barbui, M.; Stroe, L.; Tecchio, L.B.; Tonezzer, M.; Lhersonneau, G.

2009-01-01

A UC target material of 11.3±0.5 g/cm 3 uranium density with the grain size of 20 and 5μm manufactured in a form of pills by the method of powder metallurgy has been tested on-line within the temperature range of 1800-2100 C. The mass of uranium exposed to the beam was 4-7g. The yields and release rates of Cs and Fr isotopes produced by fission and spallation reactions of 238 U by 1GeV protons have been measured. The yields of Cs and Fr isotopes obtained from the tested target materials have been compared, including yields of very short-lived Fr isotopes with half-lives down to 1ms. Temperature-resistant materials (porous graphite and tantalum foil) have been used for the internal-container construction, which holds the UC target pills inside a tungsten external container heated by the resistant heating. The fastest release and the highest efficiency for short-lived isotopes have been obtained for the targets with the internal container manufactured from the tantalum foil. Results of on-line tests of a big mass target (730g of 5μm grain UC target material) have been discussed. (orig.)

Chemistry of actinides and fission products

International Nuclear Information System (INIS)

Pruett, D.J.; Sherrow, S.A.; Toth, L.M.

1988-01-01

This task is concerned primarily with the fundamental chemistry of the actinide and fission product elements. Special efforts are made to develop research programs in collaboration with researchers at universities and in industry who have need of national laboratory facilities. Specific areas currently under investigation include: (1) spectroscopy and photochemistry of actinides in low-temperature matrices; (2) small-angle scattering studies of hydrous actinide and fission product polymers in aqueous and nonaqueous solvents; (3) kinetic and thermodynamic studies of complexation reactions in aqueous and nonaqueous solutions; and (4) the development of inorganic ion exchange materials for actinide and lanthanide separations. Recent results from work in these areas are summarized here

Selection of exception limits for all actinide nuclides based on revised criteria for safe international transport and including storage delay

International Nuclear Information System (INIS)

Lavarenne, C.; Rouyer, V.; Mennerdahl, D.; Dean, C.; Barton, N.; Jean, F.

2004-01-01

Since 1998, there have been some speculations about future transport of significant quantities and concentrations of other actinide nuclides than the four currently listed in the regulation for the safe transport of the radioactive material. Therefore, it raised a need to specify exception limits for such actinides. In order to define credible exception limits, it was necessary to have reasonably accurate data for all actinide nuclides. Then the DGTREN/participants decided to perform calculations with different codes (MONK, MCNP, CRISTAL and SCALE) and different cross-section libraries (JEF2.2, ENDFB, etc.). The parameters of interest (such as k-infinite, critical masses) were determined. This article presents the work achieved and the questions raised, e.g. related to the effect of the radioactive decay of the isotopes on the criticality risks. It also points out the need for an evolution of the regulation of the safe transport of radioactive materials and gives a proposition of modification for the IAEA requirements related to, firstly, the list of the fissile materials, secondly, the rule to determine the quantities of actinide nuclides that can be excepted from the requirements for the packages containing fissile materials

Study of actinide paramagnetism in solution

International Nuclear Information System (INIS)

Autillo, Matthieu

2015-01-01

The physiochemical properties of actinide (An) solutions are still difficult to explain, particularly the behavioral differences between An(III) and Ln(III). The study of actinide paramagnetic behavior may be a 'simple' method to analyze the electronic properties of actinide elements and to obtain information on the ligand-actinide interaction. The objective of this PhD thesis is to understand the paramagnetic properties of these elements by magnetic susceptibility measurements and chemical shift studies. Studies on actinide electronic properties at various oxidation states in solution were carried out by magnetic susceptibility measurements in solution according to the Evans method. Unlike Ln(III) elements, there is no specific theory describing the magnetic properties of these ions in solution. To obtain accurate data, the influence of experimental measurement technique and radioactivity of these elements was analyzed. Then, to describe the electronic structure of their low energy states, the experimental results were complemented with quantum chemical calculations from which the influence of the ligand field was studied. Finally, these interpretations were applied to better understand the variations in the magnetic properties of actinide cations in chloride and nitrate media. Information about ligand-actinide interactions may be determined from an NMR chemical shift study of actinide complexes. Indeed, modifications induced by a paramagnetic complex can be separated into two components. The first component, a Fermi contact contribution (δ_c) is related to the degree of covalency in coordination bonds with the actinide ions and the second, a dipolar contribution (δ_p_c) is related to the structure of the complex. The paramagnetic induced shift can be used only if we can isolate these two terms. To achieve this study on actinide elements, we chose to work with the complexes of dipicolinic acid (DPA). Firstly, to characterize the geometrical parameters, a

Catalytic Organic Transformations Mediated by Actinide Complexes

Directory of Open Access Journals (Sweden)

Isabell S. R. Karmel

2015-10-01

Full Text Available This review article presents the development of organoactinides and actinide coordination complexes as catalysts for homogeneous organic transformations. This chapter introduces the basic principles of actinide catalysis and deals with the historic development of actinide complexes in catalytic processes. The application of organoactinides in homogeneous catalysis is exemplified in the hydroelementation reactions, such as the hydroamination, hydrosilylation, hydroalkoxylation and hydrothiolation of alkynes. Additionally, the use of actinide coordination complexes for the catalytic polymerization of α-olefins and the ring opening polymerization of cyclic esters is presented. The last part of this review article highlights novel catalytic transformations mediated by actinide compounds and gives an outlook to the further potential of this field.

Burn of actinides in MOX fuel cells

International Nuclear Information System (INIS)

Martinez C, E.; Ramirez S, J. R.; Alonso V, G.

2017-09-01

The spent fuel from nuclear reactors is stored temporarily in dry repositories in many countries of the world. However, the main problem of spent fuel, which is its high radio-toxicity in the long term, is not solved. A new strategy is required to close the nuclear fuel cycle and for the sustain ability of nuclear power generation, this strategy could be the recycling of plutonium to obtain more energy and recycle the actinides generated during the irradiation of the fuel to transmute them in less radioactive radionuclides. In this work we evaluate the quantities of actinides generated in different fuels and the quantities of actinides that are generated after their recycling in a thermal reactor. First, we make a reference calculation with a regular enriched uranium fuel, and then is changed to a MOX fuel, varying the plutonium concentrations and determining the quantities of actinides generated. Finally, different amounts of actinides are introduced into a new fuel and the amount of actinides generated at the end of the fuel burn is calculated, in order to determine the reduction of minor actinides obtained. The results show that if the concentration of plutonium in the fuel is high, then the production of minor actinides is also high. The calculations were made using the cell code CASMO-4 and the results obtained are shown in section 6 of this work. (Author)

Isotope and Nuclear Chemistry Division annual report FY 1986, October 1985-September 1986

International Nuclear Information System (INIS)

Heiken, J.H.

1987-06-01

This report describes progress in the major research and development programs carried out in FY 1986 by the Isotope and Nuclear Chemistry Division. The report includes articles on radiochemical diagnostics and weapons tests; weapons radiochemical diagnostics research and development; other unclassified weapons research; stable and radioactive isotope production and separation; chemical biology and nuclear medicine; element and isotope transport and fixation; actinide and transition metal chemistry; structural chemistry, spectroscopy, and applications; nuclear structure and reactions; irradiation facilities; advanced concepts and technology; and atmospheric chemistry

Isotope and Nuclear Chemistry Division annual report FY 1986, October 1985-September 1986

Energy Technology Data Exchange (ETDEWEB)

Heiken, J.H. (ed.)

1987-06-01

This report describes progress in the major research and development programs carried out in FY 1986 by the Isotope and Nuclear Chemistry Division. The report includes articles on radiochemical diagnostics and weapons tests; weapons radiochemical diagnostics research and development; other unclassified weapons research; stable and radioactive isotope production and separation; chemical biology and nuclear medicine; element and isotope transport and fixation; actinide and transition metal chemistry; structural chemistry, spectroscopy, and applications; nuclear structure and reactions; irradiation facilities; advanced concepts and technology; and atmospheric chemistry.

Development of a system for real-time measurements of metabolite transport in plants using short-lived positron-emitting radiotracers

Science.gov (United States)

Kiser, Matthew R.

Over the past 200 years, the Earth's atmospheric carbon dioxide (CO 2) concentration has increased by more than 35%, and climate experts predict that CO2 levels may double by the end of this century. Understanding the mechanisms of resource management in plants is fundamental for predicting how plants will respond to the increase in atmospheric CO 2. Plant productivity sustains life on Earth and is a principal component of the planet's system that regulates atmospheric CO2 concentration. As such, one of the central goals of plant science is to understand the regulatory mechanisms of plant growth in a changing environment. Short-lived positron-emitting radiotracer techniques provide time-dependent data that are critical for developing models of metabolite transport and resource distribution in plants and their microenvironments. To better understand the effects of environmental changes on resource transport and allocation in plants, we have developed a system for real-time measurements of rnetabolite transport in plants using short-lived positron-emitting radio-tracers. This thesis project includes the design, construction, and demonstration of the capabilities of this system for performing real-time measurements of metabolite transport in plants. The short-lived radiotracer system described in this dissertation takes advantage of the combined capabilities and close proximity of two research facilities at. Duke University: the Triangle Universities Nuclear Laboratory (TUNL) and the Duke University Phytotron, which are separated by approximately 100 meters. The short-lived positron-emitting radioisotopes are generated using the 10-MV tandem Van de Graaff accelerator located in the main TUNL building, which provides the capability of producing short-lived positron-emitting isotopes such as carbon-11 (11C: 20 minute half-life), nitrogen-13 (13N; 10 minute half-life), fluorine-18 (18F; 110 minute half-life), and oxygen-15 (15O; 2 minute half-life). The radioisotopes may

The determination of B and Sr isotopes of quaternary biologic fossils in Yanghuzhuang Yanqing basin and their living environment

International Nuclear Information System (INIS)

Xiao Yingkai; Xiao Jun; Zhao Zhiqi; He Maoyong; Li Shizhen

2007-01-01

The B and Sr isotopic compositions of early Quaternary biologic fossils in Yanghuzhuang and living bivalves in Weishui river were measured. Comparing with the data of marine foraminifer, the results show a non-marine living environment for these foraminifers lived in early Quaternary in Yanghuzhuang, Yanqing; Basin. (authors)

Minor actinide transmutation - a waste management option

International Nuclear Information System (INIS)

Koch, L.

1986-01-01

The incentive to recycle minor actinides results from the reduction of the long-term α-radiological risk rather than from a better utilization of the uranium resources. Nevertheless, the gain in generated electricity by minor actinide transmutation in a fast breeder reactor can compensate for the costs of their recovery and make-up into fuel elements. Different recycling options of minor actinides are discussed: transmutation in liquid metal fast breeder reactors (LMFBRs) is possible as long as plutonium is not recycled in light water reactors (LWRs). In this case a minor actinide burner with fuel of different composition has to be introduced. The development of appropriate minor actinide fuels and their properties are described. The irradiation experiments underway or planned are summarized. A review of minor actinide partitioning from the PUREX waste stream is given. From the present constraints of LMFBR technology a reduction of the long-term α-radiological risk by a factor of 200 is deduced relative to that from the direct storage of spent LWR fuel. Though the present accumulation of minor actinides is low, nuclear transmutation may be needed when nuclear energy production has grown. (orig.)

Isotope specific resolution recovery image reconstruction in high resolution PET imaging

OpenAIRE

Kotasidis Fotis A.; Kotasidis Fotis A.; Angelis Georgios I.; Anton-Rodriguez Jose; Matthews Julian C.; Reader Andrew J.; Reader Andrew J.; Zaidi Habib; Zaidi Habib; Zaidi Habib

2014-01-01

Purpose: Measuring and incorporating a scanner specific point spread function (PSF) within image reconstruction has been shown to improve spatial resolution in PET. However due to the short half life of clinically used isotopes other long lived isotopes not used in clinical practice are used to perform the PSF measurements. As such non optimal PSF models that do not correspond to those needed for the data to be reconstructed are used within resolution modeling (RM) image reconstruction usuall...

Evidence from stable isotopes and 10Be for solar system formation triggered by a low-mass supernova

Science.gov (United States)

Banerjee, Projjwal; Qian, Yong-Zhong; Heger, Alexander; Haxton, W. C.

2016-11-01

About 4.6 billion years ago, some event disturbed a cloud of gas and dust, triggering the gravitational collapse that led to the formation of the solar system. A core-collapse supernova, whose shock wave is capable of compressing such a cloud, is an obvious candidate for the initiating event. This hypothesis can be tested because supernovae also produce telltale patterns of short-lived radionuclides, which would be preserved today as isotopic anomalies. Previous studies of the forensic evidence have been inconclusive, finding a pattern of isotopes differing from that produced in conventional supernova models. Here we argue that these difficulties either do not arise or are mitigated if the initiating supernova was a special type, low in mass and explosion energy. Key to our conclusion is the demonstration that short-lived 10Be can be readily synthesized in such supernovae by neutrino interactions, while anomalies in stable isotopes are suppressed.

Relativistic studies in actinides

International Nuclear Information System (INIS)

Weinberger, P.; Gonis, A.

1987-01-01

In this review the theoretical background is given for a relativistic description for actinide systems. A short introduction is given of the density functional theory which forms the basis for a fully relativistic single-particle theory. A section on the Dirac Hamiltonian is followed by a brief summary on group theoretical concepts. Single site scattering is presented such that formal extensions to the case of the presence of an internal (external) magnetic field and/or anisotropic scattering are evident. Multiple scattering is discussed such that it can readily be applied also to the problem of dislocations. In connection with the problem of selfconsistency particular attention is drawn to the use of complex energies. Finally the various theoretical aspects discussed are illustrated through the results of numerical calculations. 101 refs.; 37 figs.; 5 tabs

Measurement of fission cross-section of actinides at n_TOF for advanced nuclear reactors

CERN Document Server

Calviani, Marco; Montagnoli, G; Mastinu, P

2009-01-01

The subject of this thesis is the determination of high accuracy neutron-induced fission cross-sections of various isotopes - all of which radioactive - of interest for emerging nuclear technologies. The measurements had been performed at the CERN neutron time-of-flight facility n TOF. In particular, in this work, fission cross-sections on 233U, the main fissile isotope of the Th/U fuel cycle, and on the minor actinides 241Am, 243Am and 245Cm have been analyzed. Data on these isotopes are requested for the feasibility study of innovative nuclear systems (ADS and Generation IV reactors) currently being considered for energy production and radioactive waste transmutation. The measurements have been performed with a high performance Fast Ionization Chamber (FIC), in conjunction with an innovative data acquisition system based on Flash-ADCs. The first step in the analysis has been the reconstruction of the digitized signals, in order to extract the information required for the discrimination between fission fragm...

Moessbauer effect studies with actinides

International Nuclear Information System (INIS)

Stone, J.A.

1966-01-01

Moessbauer resonance studies in the actinide elements offer a new technique for measuring solid-state properties to a region of the periodic chart where such information is relatively sparse. It is well known that the actinides, the elements with atomic numbers from 90 to 103, form a transition series due to filling of the 5f electron shell, analogous to the rare-earth series in which the 4f shell is filled. Like the rare earths, the actinide metals and compounds are expected to exhibit a variety of interesting magnetic properties, but, unlike the rare earths, there have been few studies of the magnetic behaviour of actinides, and these properties are largely unknown. The chemical properties of the actinides have been studied somewhat more extensively, and, in contrast to the rare earths, form a multiplicity of stable valence states, especially in the lighter members of the series. It is just these properties, magnetic and chemical, for which the Moessbauer effect is a valuable probe, sensitive to the magnetic and electric environment of an atom. The rare-earth series has been a particularly fruitful region in terms of the number of elements which have been shown to exhibit the Moessbauer effect, and for this reason the exploitation of the Moessbauer effect to yield new solid-state and chemical information on the rare earths is a highly active field of research today. There is every reason to believe that the actinides can be similarly studied by the Moessbauer effect. 43 refs, 6 figs, 4 tabs

Prestudy of final disposal of long-lived low and intermediate level waste

International Nuclear Information System (INIS)

Wiborgh, M.

1995-01-01

The repository for long-lived low and intermediate level waste, SFL 3-5, is foreseen to be located adjacent to the deep repository for spent encapsulated fuel, SFL 2. The SFL 3-5 repository comprises of three repository parts which will be used for the different categories of waste. In this report the work performed within a pre-study of the SFL 3-5 repository concept is summarised. The aim was to make a first preliminary and simplified assessment of the near-field as a barrier to radionuclide dispersion. A major task has been to compile information on the waste foreseen to be disposed of in SFL 3-5. The waste comprises of; low and intermediate level waste from Studsvik, operational waste from the central interim storage for spent fuel, CLAB, and the encapsulation plant, decommissioning waste from these facilities, and core components and internal parts from the reactors. The total waste volume has been estimated to about 25000 m 3 . The total activity content at repository closure is estimated to be about 1 ·10 17 Bq in SFL 3-5. At repository closure the short-lived radionuclides, for example Co-60 and Fe-55, have decayed considerably and the activity is dominated by nickel isotopes in the metallic waste from the reactors, to be disposed of in SFL 5. However, other radionuclides may be more or equally important from a safety point of view, e.g cesium-isotopes and actinides which are found in largest amounts in the SFL 3 waste. A first evaluation of the long term performance or the SFL 3-5 repository has been made. A systematic methodology for scenario formulation was tested. The near-field release of contaminants was calculated for a selected number of radionuclides and chemo-toxic elements. The radionuclide release calculations revealed that Cs-137 and Ni-63 would dominate the annual release from all repository parts during the first 1000 years after repository closure and that Ni-59 would dominate at longer times

Prestudy of final disposal of long-lived low and intermediate level waste

Energy Technology Data Exchange (ETDEWEB)

Wiborgh, M [ed.; Kemakta Konsult AB., Stockholm (Sweden)

1995-01-01

The repository for long-lived low and intermediate level waste, SFL 3-5, is foreseen to be located adjacent to the deep repository for spent encapsulated fuel, SFL 2. The SFL 3-5 repository comprises of three repository parts which will be used for the different categories of waste. In this report the work performed within a pre-study of the SFL 3-5 repository concept is summarised. The aim was to make a first preliminary and simplified assessment of the near-field as a barrier to radionuclide dispersion. A major task has been to compile information on the waste foreseen to be disposed of in SFL 3-5. The waste comprises of; low and intermediate level waste from Studsvik, operational waste from the central interim storage for spent fuel, CLAB, and the encapsulation plant, decommissioning waste from these facilities, and core components and internal parts from the reactors. The total waste volume has been estimated to about 25000 m{sup 3}. The total activity content at repository closure is estimated to be about 1 {center_dot}10{sup 17} Bq in SFL 3-5. At repository closure the short-lived radionuclides, for example Co-60 and Fe-55, have decayed considerably and the activity is dominated by nickel isotopes in the metallic waste from the reactors, to be disposed of in SFL 5. However, other radionuclides may be more or equally important from a safety point of view, e.g cesium-isotopes and actinides which are found in largest amounts in the SFL 3 waste. A first evaluation of the long term performance or the SFL 3-5 repository has been made. A systematic methodology for scenario formulation was tested. The near-field release of contaminants was calculated for a selected number of radionuclides and chemo-toxic elements. The radionuclide release calculations revealed that Cs-137 and Ni-63 would dominate the annual release from all repository parts during the first 1000 years after repository closure and that Ni-59 would dominate at longer times.

Development and application of the generator for the short-living nuclides production

International Nuclear Information System (INIS)

Tsejner, A.

1979-01-01

The results are stated of investigations by means of radioisotopes on the substance transfer in technological equipment. For these purposes, in most cases, nuclides with high gamma-activity are used and, if possible, having short half-life because the short half-life gives certain advantages in the cases when it is impossible to store radioactive substances in the technological equipment for a long time. It is noted that in connection with short half-life of the nucludes used for labelling and for the economic and radiation safety reasons, activity of these nuclides can not be high. It has been established that the most suitable nuclide for the labelling purpose is lanthanum-140 produced either in a nuclear reactor, or by means of separation from barium=-140 transforming into lanthanum-140 in an isotopic generator. Some methods of lanthanum separation from barium are described, in particular, in the isotopic generator described, barium is adsorbed on the cation-exchanger KPS-200 having high enough stability with respect to the ionozing radiations. As an eluent the 10 -2 M solution of the complexone (Na 2 - EDTA) was used. The complexone solution can be easely obtained and, because of the hydrolysis, it serves as a buffer solution. The data are given for radiation purity and yield of lanthanum-=140 [ru

Comparative studies of actinide and sub-actinide fission cross section calculation from MCNP6 and TALYS

International Nuclear Information System (INIS)

Perkasa, Y. S.; Waris, A.; Kurniadi, R.; Su'ud, Z.

2014-01-01

Comparative studies of actinide and sub-actinide fission cross section calculation from MCNP6 and TALYS have been conducted. In this work, fission cross section resulted from MCNP6 prediction will be compared with result from TALYS calculation. MCNP6 with its event generator CEM03.03 and LAQGSM03.03 have been validated and verified for several intermediate and heavy nuclides fission reaction data and also has a good agreement with experimental data for fission reaction that induced by photons, pions, and nucleons at energy from several ten of MeV to about 1 TeV. The calculation that induced within TALYS will be focused mainly to several hundred MeV for actinide and sub-actinide nuclides and will be compared with MCNP6 code and several experimental data from other evaluator

Actinide nanoparticle research

International Nuclear Information System (INIS)

Kalmykov, Stepan N.; Denecke, Melissa A.

2011-01-01

This is the first book to cover actinide nano research. It is of interest both for fundamental research into the chemistry and physics of f-block elements as well as for applied researchers such as those studying the long-term safety of nuclear waste disposal and developing remediation strategies. The authors cover important issues of the formation of actinide nano-particles, their properties and structure, environmental behavior of colloids and nanoparticles related to the safe disposal of nuclear wastes, modeling and advanced methods of characterization at the nano-scale. (orig.)

Reactor Fuel Isotopics and Code Validation for Nuclear Applications

Energy Technology Data Exchange (ETDEWEB)

Francis, Matthew W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Weber, Charles F. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Pigni, Marco T. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Gauld, Ian C. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2015-02-01

Experimentally measured isotopic concentrations of well characterized spent nuclear fuel (SNF) samples have been collected and analyzed by previous researchers. These sets of experimental data have been used extensively to validate the accuracy of depletion code predictions for given sets of burnups, initial enrichments, and varying power histories for different reactor types. The purpose of this report is to present the diversity of data in a concise manner and summarize the current accuracy of depletion modeling. All calculations performed for this report were done using the Oak Ridge Isotope GENeration (ORIGEN) code, an internationally used irradiation and decay code solver within the SCALE comprehensive modeling and simulation code. The diversity of data given in this report includes key actinides, stable fission products, and radioactive fission products. In general, when using the current ENDF/B-VII.0 nuclear data libraries in SCALE, the major actinides are predicted to within 5% of the measured values. Large improvements were seen for several of the curium isotopes when using improved cross section data found in evaluated nuclear data file ENDF/B-VII.0 as compared to ENDF/B-V-based results. The impact of the flux spectrum on the plutonium isotope concentrations as a function of burnup was also shown. The general accuracy noted for the actinide samples for reactor types with burnups greater than 5,000 MWd/MTU was not observed for the low-burnup Hanford B samples. More work is needed in understanding these large discrepancies. The stable neodymium and samarium isotopes were predicted to within a few percent of the measured values. Large improvements were seen in prediction for a few of the samarium isotopes when using the ENDF/B-VII.0 libraries compared to results obtained with ENDF/B-V libraries. Very accurate predictions were obtained for ¹³³Cs and ¹⁵³Eu. However, the predicted values for the stable ruthenium and rhodium isotopes varied

Isotope and Nuclear Chemistry Division annual report FY 1985, October 1984-September 1985

International Nuclear Information System (INIS)

Heiken, J.H.

1986-04-01

This report describes progress in the major research and development programs carried out in FY 1985 by the Isotope and Nuclear Chemistry Division. It covers radiochemical diagnostics of weapons tests; weapons radiochemical diagnostics research and development; other unclassified weapons research; stable and radioactive isotope production, separation, and applications (including biomedical applications); element and isotope transport and fixation; actinide and transition metal chemistry; structural chemistry, spectroscopy, and applications; nuclear structure and reactions; irradiations facilities; advanced analytical techniques; development and applications; atmospheric chemistry and transport; and earth and planetary processes

Oak Ridge National Laboratory's isotope enrichment program

International Nuclear Information System (INIS)

Tracy, J.G.; Aaron, W.C.

1997-01-01

The Isotope Enrichment Program (IEP) at Oak Ridge National Laboratory (ORNL) is responsible for the production and distribution of ∼225 enriched stable isotopes from 50 multi-isotopic elements. In addition, ORNL distributes enriched actinide isotopes and provides extensive physical- and chemical-form processing of enriched isotopes to meet customer requirements. For more than 50 yr, ORNL has been a major provider of enriched isotopes and isotope-related services to research, medical, and industrial institutions throughout the world. Consolidation of the Isotope Distribution Office (IDO), the Isotope Research Materials Laboratory (IRML), and the stable isotope inventories in the Isotope Enrichment Facility (IEF) have improved operational efficiencies and customer services. Recent changes in the IEP have included adopting policies for long-term contracts, which offer program stability and pricing advantages for the customer, and prorated service charges, which greatly improve pricing to the small research users. The former U.S. Department of Energy (DOE) Loan Program has been converted to a lease program, which makes large-quantity or very expensive isotopes available for nondestructive research at a nominal cost. Current efforts are being pursued to improve and expand the isotope separation capabilities as well as the extensive chemical- and physical-form processing that now exists. The IEF's quality management system is ISO 9002 registered and accredited in the United States, Canada, and Europe

Elements in biological AMS

International Nuclear Information System (INIS)

Vogel, J.S.; McAninch, J.; Freeman, S.

1996-08-01

AMS (Accelerator Mass Spectrometry) provides high detection sensitivity for isotopes whose half-lives are between 10 years and 100 million years. 14 C is the most developed of such isotopes and is used in tracing natural and anthropogenic organic compounds in the Earth's biosphere. Thirty-three elements in the main periodic table and 17 lanthanides or actinides have long lived isotopes, providing potential tracers for research in elemental biochemistry. Overlap of biologically interesting heavy elements and possible AMS tracers is discussed

Actinides reduction by recycling in a thermal reactor

International Nuclear Information System (INIS)

Ramirez S, J. R.; Martinez C, E.; Balboa L, H.

2014-10-01

This work is directed towards the evaluation of an advanced nuclear fuel cycle in which radioactive actinides could be recycled to remove most of the radioactive material; firstly a production reference of actinides in standard nuclear fuel of uranium at the end of its burning in a BWR reactor is established, after a fuel containing plutonium is modeled to also calculate the actinides production in MOX fuel type. Also it proposes a design of fuel rod containing 6% of actinides in a matrix of uranium from the tails of enrichment, then four standard uranium fuel rods are replaced by actinides rods to evaluate the production and transmutation thereof, the same procedure was performed in the fuel type MOX and the end actinide reduction in the fuel was evaluated. (Author)

Stable isotope separation in calutrons: Forty years of production and distribution

International Nuclear Information System (INIS)

Bell, W.A.; Tracy, J.G.

1987-11-01

The stable isotope separation program, established in 1945, has operated continually to provide enriched stable isotopes and selected radioactive isotopes, including the actinides, for use in research, medicine, and industrial applications. This report summarizes the first forty years of effort in the production and distribution of stable isotopes. Evolution of the program along with the research and development, chemical processing, and production efforts are highlighted. A total of 3.86 million separator hours has been utilized to separate 235 isotopes of 56 elements. Relative effort expended toward processing each of these elements is shown. Collection rates (mg/separator h), which vary by a factor of 20,000 from the highest to the lowest ( 205 Tl to 46 Ca), and the attainable isotopic purity for each isotope are presented. Policies related to isotope pricing, isotope distribution, and support for the enrichment program are discussed. Changes in government funding, coupled with large variations in sales revenue, have resulted in 7-fold perturbations in production levels

Isotope and nuclear chemistry division. Annual report, FY 1987. Progress report, October 1986-September 1987

International Nuclear Information System (INIS)

Barr, D.W.; Heiken, J.H.

1988-05-01

This report describes progress in the major research and development programs carried out in FY 1987 by the Isotope and Nuclear Chemistry Division. The report includes articles on radiochemical weapons diagnostics and research and development; other unclassified weapons research; stable and radioactive isotope production and separation; chemical biology and nuclear medicine; element and isotope transport and fixation; actinide and transition metal chemistry; structural chemistry, spectroscopy, and applications; nuclear structure and reactions; irradiation facilities; advanced concepts and technology; and atmospheric chemistry

Short-lived positron emitter labeled radiotracers - present status

International Nuclear Information System (INIS)

Fowler, J.S.; Wolf, A.P.

1982-01-01

The preparation of labelled compounds is important for the application of positron emission transaxial tomography (PETT) in biomedical sciences. This paper describes problems and progress in the synthesis of short-lived positron emitter ( 11 C, 18 F, 13 N) labelled tracers for PETT. Synthesis of labelled sugars, amino acids, and neurotransmitter receptors (pimozide and spiroperidol tagged with 11 C) is discussed in particular

Nuclear shape transition in light gold isotopes

International Nuclear Information System (INIS)

Wallmeroth, K.; Bollen, G.; Dohn, A.; Egelhof, P.; Kroenert, U.; Heyde, K.; Coster, C. de; Wood, J.L.; Kluge, H.J.; European Organization for Nuclear Research, Geneva; European Organization for Nuclear Research, Geneva

1989-01-01

The hyperfine structure and isotope shifts of short-lived gold isotopes with 185≤A≤190 and the 11/2 - isomer of 189 Au have been investigated by application of on-line resonance ionization mass spectroscopy. A detection efficiency of ε=10 -8 for gold atoms was observed at a background of about one event per 1000 laser shots. The deduced charge radii show a drastic change between A=187 and A=186 which is interpreted as an onset of strong deformation (β 2 ≅ 0.25) in 186 Au and 185 Au due to the influence of the π1h 9/2 intruder orbital. (orig.)

Synthesis of nuclear waste monazites, ideal actinide hosts for geologic disposal

International Nuclear Information System (INIS)

McCarthy, G.J.; White, W.B.; Pfoertsch, D.E.

1978-01-01

Monazite, an orthophosphate mineral of the lanthanides (Ln) and the actinides (An) U and Th, is a model for an ideal synthetic mineral waste form for geologic disposal of long-lived nuclear waste actinides. Natural monazites are known to have survived many of the conditions that might be inflicted on a nuclear waste repository by geological disruptions. High Th and U monazites with compositions typical of nuclear wastes have been synthesized with a routine calcination-pelletization-crystallization procedure. Charge balance for the Th 4+ → Ln 3+ substitution can be provided by either an equimolar Ca 2+ → Ln 3+ or Si 4+ → P 5+ substitution. For U 4+ → Ln 3+ , only the Ca 2+ → Ln 3+ substitution resulted in a phase-pure monazite. Unit cell parameter data were obtained for each nuclear waste monazite phase

Detection of long-lived plutonium isotopes in environmental samples by Accelerator Mass Spectrometry (AMS)

Energy Technology Data Exchange (ETDEWEB)

Hain, Karin; Faestermann, Thomas; Fimiani, Leticia; Gomez Guzman, Jose Manuel; Korschinek, Gunther; Ludwig, Peter [Technische Universitaet Muenchen (Germany); Shinonaga, Taeko [Helmholtz Zentrum Muenchen (Germany)

2013-07-01

The Plutonium isotopes {sup 239}Pu (T{sub 1/2}=2.4.10{sup 4}a), {sup 240}Pu (T{sub 1/2}=6.5.10{sup 3}a) and {sup 242}Pu (T{sub 1/2}=3.7.10{sup 5}a) are anthropogenic radionuclides emitted into the environment by nuclear activities. Pu is accumulated in the human body and hence, poses a considerable hazard to human health. Due to the long half-lives, these isotopes are present in the biosphere on large time scales and a build-up can be expected. Therefore it is important to study the contamination pathway of Pu into the drinking water. At the Maier-Leibnitz-Laboratory in Munich a method to detect long-lived Pu isotopes by Accelerator Mass Spectrometry (AMS) is being developed. AMS requires only few milligrams of sample material, which is a substantial advantage over decay counting techniques. Consequently, more samples from different locations can be taken which is essential when searching for locally increased Pu concentrations as in the Pacific Ocean after the Fukushima accident in March 2011. Samples from different locations in the Pacific Ocean and from the snow-hydrosphere are planned to be investigated by AMS. The principle detection method using AMS and an overview of the status of the project is presented.

The effects of actinide separation on the radiological consequences of disposal of high-level radioactive waste on the ocean bed

International Nuclear Information System (INIS)

Camplin, W.C.; Grimwood, P.D.; White, I.F.

1980-01-01

One option in the management of high-level radioactive wastes is to separate the actinides prior to vitrification and disposal. This option is examined in the context of disposal of high-level wastes on the deep ocean bed. The initial quantity of waste corresponds to the generation of 1000 GW(e)y of nuclear energy, and the actinide-separation process is assumed to remove 99% of all elements of atomic number greater than that of actinium. The models used to describe the dispersion of activity from a single disposal site on the bed of the Atlantic Ocean represent both local dispersion and long-term mixing. Collective doses and doses to individuals are calculated for six potential pathways: ingestion of fish, crustacea, molluscs, plankton and seaweed, and external irradiation from contaminated beach sediments. The period from 400 to 1,000,000 years after disposal is considered. The potential radiological impact from disposal of high-level waste without separation of actinides on the ocean bed arises from the actinides; isotopes of americium, neptunium and plutonium give the highest doses. Actinide separation would reduce these doses in proportion to the effectiveness of the separation process, until doses become determined by fission products rather than actinides: the achievable dose reduction would be a factor of approximately a hundred, or less for certain pathways. This reduction applies only to doses to the public from waste disposal: no account was taken of doses arising from the separation process itself or from the management of the separated actinides. The results of the assessment are contrasted with those of similar studies based on toxicity indices. Major deficiencies are identified in the use of toxicity indices as a basis for decision-making. (author)

PRODUCTION OF ACTINIDE METAL

Science.gov (United States)

Knighton, J.B.

1963-11-01

A process of reducing actinide oxide to the metal with magnesium-zinc alloy in a flux of 5 mole% of magnesium fluoride and 95 mole% of magnesium chloride plus lithium, sodium, potassium, calcium, strontium, or barium chloride is presented. The flux contains at least 14 mole% of magnesium cation at 600-- 900 deg C in air. The formed magnesium-zinc-actinide alloy is separated from the magnesium-oxide-containing flux. (AEC)

Rapid Separation Methods to Characterize Actinides and Metallic Impurities in Plutonium Scrap Materials at SRS

International Nuclear Information System (INIS)

Maxwell, S.L. III; Jones, V.D.

1998-07-01

The Nuclear Materials Stabilization and Storage Division at SRS plans to stabilize selected plutonium scrap residue materials for long term storage by dissolution processing and plans to stabilize other plutonium vault materials via high-temperature furnace processing. To support these nuclear material stabilization activities, the SRS Analytical Laboratories Department (ALD) will provide characterization of materials required prior to the dissolution or the high-firing of these materials. Lab renovations to install new analytical instrumentation are underway to support these activities that include glove boxes with simulated-process dissolution and high- pressure microwave dissolution capability. Inductively-coupled plasma atomic emission spectrometry (ICP-AES), inductively- coupled mass spectrometry (ICP-MS) and thermal-ionization mass spectrometry (TIMS) will be used to measure actinide isotopics and metallic impurities. New high-speed actinide separation methods have been developed that will be applied to isotopic characterization of nuclear materials by TIMS and ICP-MS to eliminate isobaric interferences between Pu-238 /U- 238 and Pu-241/Am-241. TEVA Resin, UTEVA Resin, and TRU Resin columns will be used with vacuum-assisted flow rates to minimize TIMS and ICP-MS sample turnaround times. For metallic impurity analysis, rapid column removal methods using UTEVA Resin, AGMP-1 anion resin and AG MP-50 cation resin have also been developed to remove plutonium and uranium matrix interferences prior to ICP-AES and ICP- MS measurements

Clinical studies short-lived isotopes

International Nuclear Information System (INIS)

Webber, M.D.; Victery, W.S.; Cragin, M.D.

1976-01-01

Progress is reported in the following areas of research: demonstration of intravascular thrombosis using tantalum particles and /sup 99m/Tc; correlation of MAA thrombosis scans with fibrinogen uptake test; RISA and 125 I-fibrinogen accumulation in sites of forming and formed thrombi; and clinicopathologic correlations of the 125 I thyroid scan

Potential carcinogenic effects of actinides in the environment

International Nuclear Information System (INIS)

Harley, N.H.; Pasternack, B.S.

1979-01-01

Inhalation of alpha emitting actinides delivers a dose to critical cancer sites in the human body. These sites are the bronchial epithelium and cells near bone surfaces. Inhalation of the naturally occurring actinides uranium and thorium in resuspended soil in the air results in a continuous exposure for the global population of about 0.1 fCi/m 3 for each of these actinides. The highest dose is from the natural actinide 230 Th. Over 50 yr, the dose to bronchial epithelium is 0.05 mrad and to bone surfaces 0.4 mrad. In the case of accidental environmental contamination (e.g. near a nuclear fuel reprocessing plant) the man-made actinides plutonium, americium and curium could deliver about the same alpha dose to these sites if the soil is contaminated to the same level as the natural actinides (approximately 1 pCi/g). Two nuclear accidents have already produced contamination of about this level. Exposures in this case, however, are to small local populations compared with global exposure for the natural actinides. Significant enhancement of the natural radioactive actinide pollution by combustion of all types of fossil fuel is suspected but not enough data are available to estimate total population doses. (author)

End point control of an actinide precipitation reactor

International Nuclear Information System (INIS)

Muske, K.R.

1997-01-01

The actinide precipitation reactors in the nuclear materials processing facility at Los Alamos National Laboratory are used to remove actinides and other heavy metals from the effluent streams generated during the purification of plutonium. These effluent streams consist of hydrochloric acid solutions, ranging from one to five molar in concentration, in which actinides and other metals are dissolved. The actinides present are plutonium and americium. Typical actinide loadings range from one to five grams per liter. The most prevalent heavy metals are iron, chromium, and nickel that are due to stainless steel. Removal of these metals from solution is accomplished by hydroxide precipitation during the neutralization of the effluent. An end point control algorithm for the semi-batch actinide precipitation reactors at Los Alamos National Laboratory is described. The algorithm is based on an equilibrium solubility model of the chemical species in solution. This model is used to predict the amount of base hydroxide necessary to reach the end point of the actinide precipitation reaction. The model parameters are updated by on-line pH measurements

On the suitability of lanthanides as actinide analogs

International Nuclear Information System (INIS)

Raymond, Kenneth; Szigethy, Geza

2008-01-01

With the current level of actinide materials used in civilian power generation and the need for safe and efficient methods for the chemical separation of these species from their daughter products and for long-term storage requirements, a detailed understanding of actinide chemistry is of great importance. Due to the unique bonding properties of the f-elements, the lanthanides are commonly used as structural and chemical models for the actinides, but differences in the bonding between these 4f and 5f elements has become a question of immediate applicability to separations technology. This brief overview of actinide coordination chemistry in the Raymond group at UC Berkeley/LBNL examines the validity of using lanthanide analogs as structural models for the actinides, with particular attention paid to single crystal X-ray diffraction structures. Although lanthanides are commonly accepted as reasonable analogs for the actinides, these comparisons suggest the careful study of actinide materials independent of their lanthanide analogs to be of utmost importance to present and future efforts in nuclear industries. (authors)

Ultra-trace determination of neptunium-237 and plutonium isotopes in urine samples by compact accelerator mass spectrometry

Energy Technology Data Exchange (ETDEWEB)

Dai, X.; Christl, M.; Kramer-Tremblay, S., E-mail: sheila.kramer-tremblay@cnl.ca [Canadian Nuclear Laboratories, Chalk River, Ontario (Canada); Synal, H-A. [ETH Zurich, Lab. of Ion Beam Physics, Zurich (Switzerland)

2015-12-15

Ultra-trace analysis of actinides, such as Pu isotopes and {sup 237}Np, in bioassay samples is often needed for radiation protection programs at nuclear facilities. Accelerator mass spectrometry (AMS), particularly the compact ETH Zurich system “Tandy”, has evolved over the years as one of the most sensitive, selective, and robust techniques for actinide analysis. Employment of the AMS technique can reduce the demands on sample preparation chemistry and increase sample analysis throughput, due to very low instrumental detection limit, high rejection of interferences, and low susceptibility to adverse sample matrices. Initial research and development tests were performed to explore and demonstrate the analytical capability of AMS for Pu and Np urine bioassay. In this study, urine samples spiked with femtogram levels of Np and Pu isotopes were prepared and measured using compact ETH AMS system and the results showed excellent analytical capability for measuring Np and Pu isotopes at femtogram/litre levels in urine. (author)

Review of actinide decorporation with chelating agents

Energy Technology Data Exchange (ETDEWEB)

Ansoborlo, E. [CEA Valrho, Dir. de l' Energie Nucleaire (DEN/DRCP/CETAMA), 30 - Marcoule (France); Amekraz, B.; Moulin, Ch. [CEA Saclay, Dept. de Physico-Chimie (DEN/DPC/SECR), 91 - Gif sur Yvette (France); Moulin, V. [CEA Saclay, Dir. du Developpement et de l' Innovation Nucleares (DEN/DDIN/MR), 91 - Gif Sur Yvette (France); Taran, F. [CEA Saclay (DSV/DBJC/SMMCB), 91 - Gif-sur-Yvette (France); Bailly, Th.; Burgada, R. [Centre National de la Recherche Scientifique (CNRS/LCSB/UMR 7033), 93 - Bobigny (France); Henge-Napoli, M.H. [CEA Valrho, Site de Marcoule (INSTN), 30 (France); Jeanson, A.; Den Auwer, Ch.; Bonin, L.; Moisy, Ph. [CEA Valrho, Dir. de l' Energie Nucleaire (DEN/DRCP/SCPS), 30 - Marcoule (France)

2007-10-15

In case of accidental release of radionuclides in a nuclear facility or in the environment, internal contamination (inhalation, ingestion or wound) with actinides represents a severe health risk to human beings. It is therefore important to provide effective chelation therapy or decorporation to reduce acute radiation damage, chemical toxicity, and late radiation effects. Speciation governs bioavailability and toxicity of elements and it is a prerequisite tool for the design and success of new ligands or chelating agents. The purpose of this review is to present the state-of-the-art of actinide decorporation within biological media, to recall briefly actinide metabolism, to list the basic constraints of actinide-ligand for development, to describe main tools developed and used for decorporation studies, to review mainly the chelating agents tested for actinides, and finally to conclude on the future trends in this field. (authors)

Actinide-Aluminate Speciation in Alkaline Radioactive Waste

International Nuclear Information System (INIS)

Clark, David L.; Fedosseev, Alexander M.

2001-01-01

Investigation of behavior of actinides in alkaline media containing AL(III) showed that no aluminate complexes of actinides in oxidation states (IIII-VIII) were formed in alkaline solutions. At alkaline precipitation IPH (10-14) of actinides in presence of AL(III) formation of aluminate compounds is not observed. However, in precipitates contained actinides (IIV)<(VI), and to a lesser degree actinides (III), some interference of components takes place that is reflected in change of solid phase properties in comparison with pure components or their mechanical mixture. The interference decreases with rise of precipitation PH and at PH 14 is exhibited very feebly. In the case of NP(VII) the individual compound with AL(III) is obtained, however it is not aluminate of neptunium(VII), but neptunate of aluminium(III) similar to neptunates of other metals obtained earlier

Transmutation of waste actinides in light water reactors

International Nuclear Information System (INIS)

Gorrell, T.C.

1979-04-01

Actinide recycle and transmutation calculations were made for three irradiation options of a light water reactor (LWR). The cases considered were: all actinides recycled in regular uranium fuel assemblies; transuranic actinides recycled in separate MOX assemblies with 235 U enrichment of uranium; and transuranic actinides recycled in separate MOX assemblies with plutonium enrichment of natural uranium. When all actinides were recycled in a uniform lattice, the transuranic inventory after ten recycles was 38% of the inventory accumulated without recycle. When the transuranics from two regular uranium assemblies were combined with those recycled from a MOX assembly, the transuranic inventory was reduced 50% after five recycles

Chemical compatibility of HLW borosilicate glasses with actinides

International Nuclear Information System (INIS)

Walker, C.T.; Scheffler, K.; Riege, U.

1978-11-01

During liquid storage of HLLW the formation of actinide enriched sludges is being expected. Also during melting of HLW glasses an increase of top-to-bottom actinide concentrations can take place. Both effects have been studied. Besides, the vitrification of plutonium enriched wastes from Pu fuel element fabrication plants has been investigated with respect to an isolated vitrification process or a combined one with the HLLW. It is shown that the solidification of actinides from HLLW and actinide waste concentrates will set no principal problems. The leaching of actinides has been measured in salt brine at 23 0 C and 115 0 C. (orig.) [de

The oxygen isotope composition of earth's oldest rocks and evidence of a terrestrial magma ocean

DEFF Research Database (Denmark)

Rumble, D.; Bowring, S.; Iizuka, T.

2013-01-01

Analysis of Hadean and Archean rocks for O-16-O-17-O-18 isotopes demonstrates that the Terrestrial Mass Fractionation Line of oxygen isotopes has had the same slope and intercept for at least the past 4.0 and probably for as long as 4.2Ga. The homogenization of oxygen isotopes required to produce....... But other sources of heat for global melting cannot be excluded such as bolide impacts during early accretion of proto-Earth, the decay of short-lived radioactive isotopes, or the energy released during segregation of core from mantle.......Analysis of Hadean and Archean rocks for O-16-O-17-O-18 isotopes demonstrates that the Terrestrial Mass Fractionation Line of oxygen isotopes has had the same slope and intercept for at least the past 4.0 and probably for as long as 4.2Ga. The homogenization of oxygen isotopes required to produce...... such long-lived consistency was most easily established by mixing in a terrestrial magma ocean. The measured identical oxygen isotope mass fractionation lines for Earth and Moon suggest that oxygen isotope reservoirs of both bodies were homogenized at the same time during a giant moon-forming impact...

Sizes and shapes of short-lived nuclei via laser spectroscopy. Final report

International Nuclear Information System (INIS)

Lewis, D.A.

1985-10-01

This project, a collaboration involving Iowa State University, Argonne National Lab., and the University of Minnesota, was aimed at the determination of properties of short-lived nuclei through their atomic hyperfine structure and optical isotope shifts. The basic approach was to use a cryogenic He-jet system to thermalize, neutralize, and transport radioactive nuclei produced online into a region suitable for laser spectroscopy. The photon burst method was then used for high sensitivity with the resulting continuous atomic beam. The experiment was located on beamline of the ANL superconducting heavy-ion accelerator. The He-jet system developed would reliably transport approx.10 2 nuclei into phase space useful for high resolution laser spectroscopy. The laser system developed could accurately and reproducibly sweep small frequency ranges for periods greater than or equal to1 day and sensitivity limits less than or equal to1 atom/s were achieved. However the nuclei were not transported as free atoms precluding nuclear determinations. Attempts to obtain free atoms by eliminating turbulence and contamination were not successful. Some of the high sensitivity spectroscopy techniques developed in this work are now being applied in a search for nuclear relics of the Big Bang and in studies of the photon statistics of light scattered by a single atom. 3 refs., 4 figs

Detection of 210Po on filter papers 16 years after use for the collection of short-lived radon progeny in a room

International Nuclear Information System (INIS)

Abu-Jarad, F.; Fazal-ur-Rehman

2003-01-01

Radon gas was allowed to accumulate in its radium source and then injected into a 36 m 3 test room, resulting in an initial radon concentration of 15 kBq m -3 . Filter papers were used to collect the short-lived radon progeny and thus to measure the Potential Alpha Energy Concentration (PAEC) in-situ in the year 1984 at different times and conditions according to the experimental design. The radon progeny collected on the filter papers were studied as a function of aerosol particle concentration ranging from 10 2 -10 5 particles cm -3 in three different experiments. The highest aerosol particle concentration was generated by indoor cigarette smoking. Those filters were stored after the experiment, and were used after 16 years to study the activity of the radon long-lived alpha emitter progeny, 210 Po (T 1/2 =138 days). This isotope is separated from the short-lived progeny by 210 Pb beta emitter with 22.3 years half-life. After 16 years' storage of these filters, each filter paper was sandwiched and wrapped between two CR-39 nuclear track detectors, to put the detectors in contact with the surfaces of different filters, for 337 days. Correlation between the PAEC measured using filter papers in the year 1984 and the activity of long-lived alpha emitter 210 Po on the same filter papers measured in the year 2000 were studied. The results of the 210 Po activity showed a very good correlation of 0.92 with the PAEC 16 years ago. The results also depict that the PAEC and 210 Po activity in indoor air increased with the increase of aerosol particle concentration, which shows the attachment of short-lived radon progeny with the aerosol particles. The experiment proves that indoor cigarette smoking is a major source of aerosol particles carrying radon progeny and, thus, indoor cigarette smoking is an additional source of internal radiation hazard to the occupants whether smoker or non-smoker

Static, Mixed-Array Total Evaporation for Improved Quantitation of Plutonium Minor Isotopes in Small Samples

Science.gov (United States)

Stanley, F. E.; Byerly, Benjamin L.; Thomas, Mariam R.; Spencer, Khalil J.

2016-06-01

Actinide isotope measurements are a critical signature capability in the modern nuclear forensics "toolbox", especially when interrogating anthropogenic constituents in real-world scenarios. Unfortunately, established methodologies, such as traditional total evaporation via thermal ionization mass spectrometry, struggle to confidently measure low abundance isotope ratios (evaporation techniques as a straightforward means of improving plutonium minor isotope measurements, which have been resistant to enhancement in recent years because of elevated radiologic concerns. Results are presented for small sample (~20 ng) applications involving a well-known plutonium isotope reference material, CRM-126a, and compared with traditional total evaporation methods.

Advances in computational actinide chemistry in China

Energy Technology Data Exchange (ETDEWEB)

Wang, Dongqi; Wu, Jingyi; Chai, Zhifang [Chinese Academy of Sciences, Beijing (China). Multidisciplinary Initiative Center; Su, Jing [Chinese Academy of Sciences, Shanghai (China). Div. of Nuclear Materials Science and Engineering; Li, Jun [Tsinghua Univ., Beijing (China). Dept. of Chemistry and Laboratory of Organic Optoelectronics and Molecular Engineering

2014-04-01

The advances in computational actinide chemistry made in China are reviewed. Several areas relevant to chemistry of actinides in gas, liquid, and solid phases have been explored. However, we limit the scope to selected contributions in the chemistry of molecular actinide systems in gas and liquid phases. These studies may be classified into two categories: treatment of relativistic effects, which cover the development of two- and four-component Hamiltonians and the optimization of relativistic pseudopotentials, and the applications of theoretical methods in actinide chemistry. The applications include (1) the electronic structures of actinocene, noble gas complexes, An-C multiple bonding compounds, uranyl and its isoelectronic species, fluorides and oxides, molecular systems with metal-metal bonding in their isolated forms (U{sub 2}, Pu{sub 2}) and in fullerene (U{sub 2} rate at C{sub 60}), and the excited states of actinide complexes; (2) chemical reactions, including oxidation, hydrolysis of UF{sub 6}, ligand exchange, reactivities of thorium oxo and sulfido metallocenes, CO{sub 2}/CS{sub 2} functionalization promoted by trivalent uranium complex; and (3) migration of actinides in the environment. A future outlook is discussed. (orig.)

Report on the IAEA coordinated research programme on the intercomparison of evaluations of actinide neutron nuclear data

International Nuclear Information System (INIS)

Yiftah, S.

1979-03-01

Following discussions and Consultants Meeting in 1976, the IAEA, in response to recommendations made formed two coordinated research projects (CRP): one on the Intercomparison of Evaluations of Actinide Neutron Nuclear Data, the other on the Measurement and Evaluation of Transactinium Isotope Nuclear Decay Data. This report covers work done, and to be done, in the framework of the first CRP, as well as some of the practical problems for future work. (B.G.)

Transmutation of minor actinide using thorium fueled BWR core

International Nuclear Information System (INIS)

Susilo, Jati

2002-01-01

One of the methods to conduct transmutation of minor actinide is the use of BWR with thorium fuel. Thorium fuel has a specific behaviour of producing a little secondary minor actinides. Transmutation of minor actinide is done by loading it in the BWR with thorium fuel through two methods, namely close recycle and accumulation recycle. The calculation of minor actinide composition produced, weigh of minor actinide transmuted, and percentage of reminder transmutation was carried SRAC. The calculations were done to equivalent cell modeling from one fuel rod of BWR. The results show that minor actinide transmutation is more effective using thorium fuel than uranium fuel, through both close recycle and accumulation recycle. Minor actinide transmutation weight show that the same value for those recycle for 5th recycle. And most of all minor actinide produced from 5 unit BWR uranium fuel can transmuted in the 6 t h of close recycle. And, the minimal value of excess reactivity of the core is 12,15 % Δk/k, that is possible value for core operation

Evaluation of the technical feasibility of new conditioning matrices for long-lived radionuclides

International Nuclear Information System (INIS)

Deschanels, X.

2004-01-01

Several matrices have been selected for the conditioning of long-lived radioactive wastes: a compound made of a iodo-apatite core coated with a densified matrice of vanadium-phosphorus-lead apatite for iodine; the hollandite ceramic for cesium; the britholite, zirconolite, thorium phosphate diphosphate, and the monazite-brabantite solid solution for minor actinides; and a Nb-based metal alloy and phosphate or titanate-type ceramics for technetium. This report presents the results of the researches carried out between 2002-2004 during the technical feasibility step. The main points described are: - the behaviour of matrices under irradiation. These studies were performed thanks to an approach combining the characterization of natural analogues, the doping of matrices with short-lived radionuclides and the use of external irradiations; - the behaviour of these matrices with respect to water alteration; - the sensibility of these structures with respect to the incorporation of chemical impurities; - a package-process approach including the optimization of the process and preliminary studies about the package concept retained. These studies show that important work remains to be done to develop conditioning matrices suitable for iodine and technetium, while for cesium and minor actinides, the first steps of the technical feasibility are made. However, it remains impossible today to determine the structure having the best global behaviour. (J.S.)

Actinide recovery from waste and low-grade sources

International Nuclear Information System (INIS)

Navratil, J.D.; Schulz, W.W.

1982-01-01

Actinide and nuclear fuel cycle operations generate a variety of process waste streams. New methods are needed to remove and recover actinides. More interest is also being expressed in recovering uranium from oceans, phosphoric acid, and other low grade sources. To meet the need for an up-to-date status report in the area of actinide recovery from waste and low grade sources, these papers were brought together. The papers provide an authoritative, in-depth coverage of an important area of nuclear and industrial and engineering chemistry which cover the following topics: uranium recovery from oceans and phosphoric acid; recovery of actinides from solids and liquid wastes; plutonium scrap recovery technology; and other new developments in actinide recovery processes

Transmutation of LWR waste actinides in thermal reactors

International Nuclear Information System (INIS)

Gorrell, T.C.

1979-01-01

Recycle of actinides to a reactor for transmutation to fission products is being considered as a possible means of waste disposal. Actinide transmutation calculations were made for two irradiation options in a thermal (LWR) reactor. The cases considered were: all actinides recycled in regular uranium fuel assemblies, and transuranic actinides recycled in separate mixed oxide (MOX) assemblies. When all actinides were recycled in a uranium lattice, a reduction of 62% in the transuranic inventory was achieved after 10 recycles, compared to the inventory accumulated without recycle. When the transuranics from 2 regular uranium assemblies were combined with those recycled from a MOX assembly, the transuranic inventory was reduced 50% after 5 recycles

A technique for the measurement of electron attachment to short-lived excited species

International Nuclear Information System (INIS)

Christophorou, L.G.; Pinnaduwage, L.A.; Bitouni, A.P.

1990-01-01

A technique is described for the measurement of electron attachment to short-lived (approx-lt 10 -9 s) excited species. Preliminary results are presented for photoenhanced electron attachment to short-lived electronically-excited states of triethylamine molecules produced by laser two-photon excitation. The attachment cross sections for these excited states are estimated to be >10 -11 cm 2 and are ∼10 7 larger compared to those for the unexcited (ground-state) molecules. 8 refs., 4 figs

Disentangling the effects of CO2 and short-lived climate forcer mitigation

NARCIS (Netherlands)

Rogelj, J.; Schaeffer, M.; Meinshausen, M.; Shindell, D.T.; Hare, W.; Klimont, Z.; Velders, G.J.M.; Amann, M.; Schellnhuber, H.J.

2014-01-01

Anthropogenic global warming is driven by emissions of a wide variety of radiative forcers ranging from very short-lived climate forcers (SLCFs), like black carbon, to very long-lived, like CO2. These species are often released from common sources and are therefore intricately linked. However, for

Actinide science. Fundamental and environmental aspects

International Nuclear Information System (INIS)

Choppin, Gregory R.

2005-01-01

Nuclear test explosions and reactor wastes have deposited an estimated 16x10 15 Bq of plutonium into the world's aquatic systems. However, plutonium concentration in open ocean waters is orders of magnitude less, indicating that most of the plutonium is quite insolvable in marine waters and has been incorporated into sediments. Actinide ions in waters often are not in a state of thermodynamic equilibrium and their solubility and migration behavior is related to the form in which the nuclides were introduced into the aquatic system. Actinide solubility depends on such factors as pH(hydrolysis), E H (oxidation state), reaction with complexants (e.g. carbonate, phosphate, humic acid, etc.) sorption to surfaces of minerals and/or colloids, etc., in the water. The most significant of these variables is the oxidation sate of the metal ion. The simultaneous presence of more than one oxidation state for some actinides (e.g. plutonium) in a solution complicates actinide environmental behavior. Both Np(V)O 2 + and Pu(V)O 2 + , the most significant soluble states in natural oxic waters are relatively noncomplexing and resistant to hydrolysis and subsequent precipitation but can undergo reduction to the Pu(IV) oxidation state with its different elemental behavior. The solubility of NpO 2 + can be as high as 10 -4 M while that of PuO 2 + is more limited by reduction to the insoluble tetravalent species, Pu(OH) 4 , (pK SP - 56). The net solubility of hexavalent UO 2 2+ in sea water is also limited by hydrolysis; however, it has a relatively high concentration due to formation of carbonate complexes. The insoluble trivalent americium hydroxocarbonate, Am(CO) 3 (OH), is the limiting species for the solubility of Am(III) in sea water. Thorium is found exclusively as the tetravalent species and its solubility is limited by the formation of quite insoluble Th(OH) 4 . The chemistry of actinide ions in the environment is reviewed to show the spectrum of reactions that can occur in

Solubility of actinides and surrogates in nuclear glasses

International Nuclear Information System (INIS)

Lopez, Ch.

2003-01-01

The nuclear wastes are currently incorporated in borosilicate glass matrices. The resulting glass must be perfectly homogeneous. The work discussed here is a study of actinide (thorium and plutonium) solubility in borosilicate glass, undertaken to assess the extent of actinide solubility in the glass and to understand the mechanisms controlling actinide solubilization. Glass specimens containing; actinide surrogates were used to prepare and optimize the fabrication of radioactive glass samples. These preliminary studies revealed that actinide Surrogates solubility in the glass was enhanced by controlling the processing temperature, the dissolution kinetic of the surrogate precursors, the glass composition and the oxidizing versus reducing conditions. The actinide solubility was investigated in the borosilicate glass. The evolution of thorium solubility in borosilicate glass was determined for temperatures ranging from 1200 deg C to 1400 deg C.Borosilicate glass specimens containing plutonium were fabricated. The experimental result showed that the plutonium solubility limit ranged from 1 to 2.5 wt% PuO 2 at 1200 deg C. A structural approach based on the determination of the local structure around actinides and their surrogates by EXAFS spectroscopy was used to determine their structural role in the glass and the nature of their bonding with the vitreous network. This approach revealed a correlation between the length of these bonds and the solubility of the actinides and their surrogates. (author)

Fusion barrier characteristics of actinides

Science.gov (United States)

Manjunatha, H. C.; Sridhar, K. N.

2018-03-01

We have studied fusion barrier characteristics of actinide compound nuclei with atomic number range 89 ≤ Z ≤ 103 for all projectile target combinations. After the calculation of fusion barrier heights and positions, we have searched for their parameterization. We have achieved the empirical formula for fusion barrier heights (VB), positions (RB), curvature of the inverted parabola (ħω) of actinide compound nuclei with atomic number range 89 ≤ Z ≤ 103 for all projectile target combinations (6 projectile target combinations. The values produced by the present formula are also compared with experiments. The present pocket formula produces fusion barrier characteristics of actinides with the simple inputs of mass number (A) and atomic number (Z) of projectile-targets.

Programme and Abstracts. 38. Journees des Actinides together with the 7. School on the Physics and Chemistry of the Actinides

Energy Technology Data Exchange (ETDEWEB)

NONE

2008-07-01

Journees des Actinides (JdA) is a traditional informal actinide forum, including physics, chemistry, and materials research. It regularly brings together experts from fields involved, taking place in a very informal way, emphasizing exchanges and discussions on current issues in actinide science. At the 38{sup th} JdA (10-15 April 2008; Wroclaw, Poland) scientific communications on the following topics on physics and chemistry of the actinides were presented: (a) inorganic and organometallic chemistry; (b) strongly correlated behaviour, superconductivity, quantum criticality; (c) materials science; (d) theory, electronic structure; (e) nuclear fuel cycle, environment.

Programme and Abstracts. 38. Journees des Actinides together with the 7. School on the Physics and Chemistry of the Actinides

International Nuclear Information System (INIS)

2008-01-01

Journees des Actinides (JdA) is a traditional informal actinide forum, including physics, chemistry, and materials research. It regularly brings together experts from fields involved, taking place in a very informal way, emphasizing exchanges and discussions on current issues in actinide science. At the 38 th JdA (10-15 April 2008; Wroclaw, Poland) scientific communications on the following topics on physics and chemistry of the actinides were presented: (a) inorganic and organometallic chemistry; (b) strongly correlated behaviour, superconductivity, quantum criticality; (c) materials science; (d) theory, electronic structure; (e) nuclear fuel cycle, environment

SPATIAL Short Courses Build Expertise and Community in Isotope Geochemistry

Science.gov (United States)

Riggs, E. M.; Bowen, G. J.

2015-12-01

The SPATIAL short course at the University of Utah is designed for graduate students and professionals in the earth and environmental sciences from around the globe. An integral part of the broader, NSF-funded Inter-university Training for Continental-scale Ecology (ITCE) project, the course is an intensive two-week field, classroom and laboratory experience with internationally-known researchers as instructors. The course focuses on stable isotope geochemistry coupled with spatial analysis techniques. Participants do not typically know each other or this research community well upon entering. One of the stated goals of the overall project is to build a community of practice around these techniques. This design is common in many professional fields, but is not often applied at the graduate level nor formally assessed in the earth sciences. Paired pre- and post-tests were administered before the start and after the close of the short courses over 3 years. The survey is a set of instruments adapted from social-cognitive psychology measuring changes in identity and community with other items to measure content knowledge outcomes. We see a subtle, consistent convergence of identities between large-scale isotope geochemistry and participants' research areas. Results also show that the course generates an increase in understanding about stable isotopes' use and application. The data show the SPATIAL course is very effective at bringing students together socially with each other and with faculty to create an environment that fosters community and scientific cooperation. Semi-structured pre-and post- interviews were conducted to understand the program elements that generated gains in learning and community. Participants were selected based on initial responses on the pre-survey to capture the range of initial conditions for the group. Qualitative analysis shows that the major factors for participants were 1) ready access to researchers in an informal setting during the

High-accuracy mass measurements of neutron-rich Kr isotopes

CERN Document Server

Delahaye, P; Blaum, K; Carrel, F; George, S; Herfurth, F; Herlert, A; Kellerbauer, A G; Kluge, H J; Lunney, D; Schweikhard, L; Yazidjian, C

2006-01-01

The atomic masses of the neutron-rich krypton isotopes 84,86-95Kr have been determined with the tandem Penning trap mass spectrometer ISOLTRAP with uncertainties ranging from 20 to 220 ppb. The masses of the short-lived isotopes 94Kr and 95Kr were measured for the first time. The masses of the radioactive nuclides 89Kr and 91Kr disagree by 4 and 6 standard deviations, respectively, from the present Atomic-Mass Evaluation database. The resulting modification of the mass surface with respect to the two-neutron separation energies as well as implications for mass models and stellar nucleosynthesis are discussed.

Actinide Source Term Program, position paper. Revision 1

International Nuclear Information System (INIS)

Novak, C.F.; Papenguth, H.W.; Crafts, C.C.; Dhooge, N.J.

1994-01-01

The Actinide Source Term represents the quantity of actinides that could be mobilized within WIPP brines and could migrate with the brines away from the disposal room vicinity. This document presents the various proposed methods for estimating this source term, with a particular focus on defining these methods and evaluating the defensibility of the models for mobile actinide concentrations. The conclusions reached in this document are: the 92 PA open-quotes expert panelclose quotes model for mobile actinide concentrations is not defensible; and, although it is extremely conservative, the open-quotes inventory limitsclose quotes model is the only existing defensible model for the actinide source term. The model effort in progress, open-quotes chemical modeling of mobile actinide concentrationsclose quotes, supported by a laboratory effort that is also in progress, is designed to provide a reasonable description of the system and be scientifically realistic and supplant the open-quotes Inventory limitsclose quotes model

Limitations of actinide recycle and waste disposal consequences

International Nuclear Information System (INIS)

Baetsle, L.H.; Raedt, C. de

1994-01-01

The paper emphasizes the impact of Light Water Reactor - Mixed Oxides introduction on the subsequent actinide management and fate of reprocessed and depleted uranium. The spent fuel from LWR-MOX contains in principle 75% of the initially produced plutonium. This new source term has to be considered together with the minor actinides from the conventional reprocessing. Subsequent LWR-MOX reprocessing in the first step in a very long term Pu + minor actinides management. Recycling of Pu + minor actinides in fast reactors to significantly reduce the Pu and minor actinides inventory (e.g. a factor of 10) is a very slow process which requires the development and operation of a large park of actinide burner reactors during an extended period of time. The overall feasibility of the P and T option will greatly depend on the massive introduction during the next century of fast neutron reactors as a replacement to the present LWR generation of nuclear power plants. (authors). 11 refs., 6 tabs., 2 figs

33rd Actinide Separations Conference

Energy Technology Data Exchange (ETDEWEB)

McDonald, L M; Wilk, P A

2009-05-04

Welcome to the 33rd Actinide Separations Conference hosted this year by the Lawrence Livermore National Laboratory. This annual conference is centered on the idea of networking and communication with scientists from throughout the United States, Britain, France and Japan who have expertise in nuclear material processing. This conference forum provides an excellent opportunity for bringing together experts in the fields of chemistry, nuclear and chemical engineering, and actinide processing to present and discuss experiences, research results, testing and application of actinide separation processes. The exchange of information that will take place between you, and other subject matter experts from around the nation and across the international boundaries, is a critical tool to assist in solving both national and international problems associated with the processing of nuclear materials used for both defense and energy purposes, as well as for the safe disposition of excess nuclear material. Granlibakken is a dedicated conference facility and training campus that is set up to provide the venue that supports communication between scientists and engineers attending the 33rd Actinide Separations Conference. We believe that you will find that Granlibakken and the Lake Tahoe views provide an atmosphere that is stimulating for fruitful discussions between participants from both government and private industry. We thank the Lawrence Livermore National Laboratory and the United States Department of Energy for their support of this conference. We especially thank you, the participants and subject matter experts, for your involvement in the 33rd Actinide Separations Conference.

33rd Actinide Separations Conference

International Nuclear Information System (INIS)

McDonald, L.M.; Wilk, P.A.

2009-01-01

Welcome to the 33rd Actinide Separations Conference hosted this year by the Lawrence Livermore National Laboratory. This annual conference is centered on the idea of networking and communication with scientists from throughout the United States, Britain, France and Japan who have expertise in nuclear material processing. This conference forum provides an excellent opportunity for bringing together experts in the fields of chemistry, nuclear and chemical engineering, and actinide processing to present and discuss experiences, research results, testing and application of actinide separation processes. The exchange of information that will take place between you, and other subject matter experts from around the nation and across the international boundaries, is a critical tool to assist in solving both national and international problems associated with the processing of nuclear materials used for both defense and energy purposes, as well as for the safe disposition of excess nuclear material. Granlibakken is a dedicated conference facility and training campus that is set up to provide the venue that supports communication between scientists and engineers attending the 33rd Actinide Separations Conference. We believe that you will find that Granlibakken and the Lake Tahoe views provide an atmosphere that is stimulating for fruitful discussions between participants from both government and private industry. We thank the Lawrence Livermore National Laboratory and the United States Department of Energy for their support of this conference. We especially thank you, the participants and subject matter experts, for your involvement in the 33rd Actinide Separations Conference.

TUCS/phosphate mineralization of actinides

Energy Technology Data Exchange (ETDEWEB)

Nash, K.L. [Argonne National Lab., IL (United States)

1997-10-01

This program has as its objective the development of a new technology that combines cation exchange and mineralization to reduce the concentration of heavy metals (in particular actinides) in groundwaters. The treatment regimen must be compatible with the groundwater and soil, potentially using groundwater/soil components to aid in the immobilization process. The delivery system (probably a water-soluble chelating agent) should first concentrate the radionuclides then release the precipitating anion, which forms thermodynamically stable mineral phases, either with the target metal ions alone or in combination with matrix cations. This approach should generate thermodynamically stable mineral phases resistant to weathering. The chelating agent should decompose spontaneously with time, release the mineralizing agent, and leave a residue that does not interfere with mineral formation. For the actinides, the ideal compound probably will release phosphate, as actinide phosphate mineral phases are among the least soluble species for these metals. The most promising means of delivering the precipitant would be to use a water-soluble, hydrolytically unstable complexant that functions in the initial stages as a cation exchanger to concentrate the metal ions. As it decomposes, the chelating agent releases phosphate to foster formation of crystalline mineral phases. Because it involves only the application of inexpensive reagents, the method of phosphate mineralization promises to be an economical alternative for in situ immobilization of radionuclides (actinides in particular). The method relies on the inherent (thermodynamic) stability of actinide mineral phases.

Hydrothermal decomposition of actinide(IV oxalates: a new aqueous route towards reactive actinide oxide nanocrystals

Directory of Open Access Journals (Sweden)

Walter Olaf

2016-01-01

Full Text Available The hydrothermal decomposition of actinide(IV oxalates (An= Th, U, Pu at temperatures between 95 and 250 °C is shown to lead to the production of highly crystalline, reactive actinide oxide nanocrystals (NCs. This aqueous process proved to be quantitative, reproducible and fast (depending on temperature. The NCs obtained were characterised by X-ray diffraction and TEM showing their size to be smaller than 15 nm. Attempts to extend this general approach towards transition metal or lanthanide oxalates failed in the 95–250 °C temperature range. The hydrothermal decomposition of actinide oxalates is therefore a clean, flexible and powerful approach towards NCs of AnO2 with possible scale-up potential.

A new methodology involving stable isotope tracer to compare short- and long- term selenium mobility in soils

Science.gov (United States)

Tolu, Julie; Thiry, Yves; Potin-gautier, Martine; Le hécho, Isabelle; Bueno, Maïté

2013-04-01

Selenium is an element of environmental concern given its dual beneficial and toxic character to animal and human health. Its radioactive isotope 79Se, a fission product of 235U, is considered critical in safety assessment of nuclear waste repositories in case of leakage and hypothetical soil contamination. Therefore, Se species transformations and interactions with soil components have to be clearly understood to predict its dispersion in the biosphere (e.g., accumulation in soils, migration to waters, transfer to living organisms). While natural Se interactions with soils run over centuries to millennia time scales, transformations and partitioning are generally studied with short-term experiments (often inferior to 1 month) after Se addition. The influence of slower, long-term processes involved in Se speciation and mobility in soils is thus not properly accounted for. We tested if using ambient Se would be relevant for long-term risk assessment while added Se would be more representative of short-term contamination impact. For that purpose, we developed a new methodology to trace the differential reactivity of ambient and spiked Se at trace level (µg kg-1) in soils. It combined the use of a stable isotopically enriched tracer with our previous published analytical method based on specific extractions and HPLC-ICP-MS to determine trace Se species partition in different soil phases. Given that soil extracts contains very high concentrations of various elements interfering Se (e.g., Fe, Cl, Br), the ICP-MS parameters and mathematical corrections were optimized to cope with such interferences. Following optimization, three correct and accurate (<2%) isotope ratios were obtained with 77Se, 78Se, 80Se and 82Se. The optimized method was then applied to an arable and a forest soil submitted to an aging process (drying/wetting cycles) during three months, to which 77Se(IV) was previously added. The results showed that ambient Se was at steady state in terms of water

A systematic study of actinide production from the interactions of heavy ions with sup 248 Cm

Energy Technology Data Exchange (ETDEWEB)

Leyba, J.D.

1990-09-07

Production cross sections for heavy actinides produced from the interactions of {sup 12}C, {sup 31}P, {sup 40}Ar, and {sup 44}Ca ions with {sup 248}Cm were measured at energies ranging from 0.98 to 1.35 X Coulomb barrier. The recoiling reaction products were collected in copper or gold catcher foils located near the {sup 248}Cm target. Separate fractions of Bk, Cf, Es, Fm, and Md were obtained from a radiochemical separation procedure. For the {sup 12}C system, a He/KCl jet was used to transport the recoiling No activities of interest to a rotating wheel system. The isotopic distributions of the actinide products were found to be essentially symmetric about the maximum with full-widths-at-half-maximum of approximately 2.5 mass units. Isotopic distributions of the {sup 12}C, {sup 31}P, {sup 40}Ar, and {sup 44}Ca systems were found to be very similar to the {sup 40,48}Ca systems studied previously. The maxima of the isotopic distributions generally occurred for those reaction channels which involved the exchange of the fewest number of nucleons between the target and projectile for which the calculated excitation energy was a positive quantity. Additionally, the maxima of the excitation functions occurred at those projectile energies which were consistent with the calculated reaction barriers based upon a binary reaction mechanism. The experimental data from the four systems investigated were compared to several models of heavy ion interactions including a damped reaction mechanism, compound nucleus formation and subsequent particle evaporation, and classical partial wave calculations for binary systems.

Project 'Installation of a stand at the horizontal channel of the MARIA Research Reactor, Otwock-Swierk, Poland, for the research of transmutation of minor actinides and fission products'

International Nuclear Information System (INIS)

Szuta, M.

2006-01-01

As a long range objective we would like to focus on management of the fuel economy in the sub-critical assembly of the accelerator driven system (ADS) in terms of long lived fission products (LLFP) and minor actinides (MA) transmutation. Transmutation of the radioactive waste (RW) is an important element within the technical objective of the optimal management of the fuel economy in the sub-critical assembly of the accelerator driven system (ADS). Analysis of possible ways of reduction of radioactive wastes by transmutation of radioactive long-lived fission products such as 99 Tc, 129 I and 135 Cs and by burning up of transuranic nuclides implies that the sub-critical assembly of the accelerator driven system should consist of three zones. The requirement of three zones comes out of the fact that each radioactive isotope to be reduced is to be located in a different spectrum of thermal, epithermal and high energy neutron fluxes. High flux thermal neutron environment (≥10 16 n/cm 3 ·s) is expected as the best way for the transmutation of most of the radioactive waste to stable or short-lived nuclides and for increasing the probability for fission such actinides as 237 Np and 238 Np. The concept of ADS system for energy production and for transmutation is quite new to some extent and from this reason it requires many theoretical and experimental studies. The research of transmutation is a very large area of study requiring a significant experimental and financial support, so it can be performed only within the international cooperation. Specifically, the proposed research within this CRP requires important means, in terms of high-energy proton beams, spallation targets, sub-critical assembly, measurement instrumentation, post-irradiation characterisation and its testing and, of course, manpower for the interpretation of results, modelling observed phenomena, and programme management. The personal involved in the research is to be a skilled personal of

Recycling of actinides and nuclear waste products. Annual report from the research programme 1996

International Nuclear Information System (INIS)

Konings, R.J.M.; Bakker, K.; Dodd, D.H.; Gruppelaar, H.; De Haas, J.B.M.; Kloosterman, J.L.

1997-07-01

The research program on the title subject started in 1994 and is planned to be completed in 1998. In this period several technical and scientific aspects of recycling and transmutation are investigated in different projects. The results of the 1996 projects are summarized and described in this report. The 1996 projects concern (1) the chemistry of actinides and inert matrices to test and characterize the matrices and actinide compounds in order to develop uranium-free fissionable materials for the transmutation of actinides; (2) the transmutation of plutonium in light water reactors (LWR) to assess and increase the burnup of plutonium and to assess the safety of plutonium transmutation in LWRs; (3) the radiological consequences of different nuclear fuel cycles; (4) and a reactor physics analysis of new thorium-based reactor systems to study the possibility to reduce the amount of long-living radioactive waste materials by means of the use of thorium-based compounds in a high-temperature reactor (HTR) or accelerators. 15 figs., 6 tabs., 23 refs

Research for actinides extractants from various wastes

International Nuclear Information System (INIS)

Musikas, C.; Cuillerdier, C.; Condamines, N.

1990-01-01

This paper is an overview of the actinides solvent extraction research undertaken in Fontenay-aux-Roses. Two kinds of extractants are investigated; those usable for the improvement of the nowadays nuclear fuels reprocessing and those necessary for advanced fuels cycles which include the minor actinides (Np, Am) recovery for a further elimination through nuclear reactions. In the first class the mono and diamides, alternative to the organophosphorus extractants, TBP and polyfunctional phosphonates, showed promising properties. The main results are discussed. For the future efficient extractants for trivalent actinides-lanthanides group separations are suitable. The point about the actinides (III) - lanthanides (III) group separation chemistry and the development of some of these extractants are given

Superconductivity in the actinides

International Nuclear Information System (INIS)

Smith, J.L.; Lawson, A.C.

1985-01-01

The trends in the occurrence of superconductivity in actinide materials are discussed. Most of them seem to show simple transition metal behavior. However, the superconductivity of americium proves that the f electrons are localized in that element and that ''actinides'' is the correct name for this row of elements. Recently the superconductivity of UBe 13 and UPt 3 has been shown to be extremely unusual, and these compounds fall in the new class of compounds now known as heavy fermion materials

Use of fast reactors for actinide transmutation. Proceedings of a specialists meeting held in Obninsk, Russian Federation, 22-24 September 1992

Energy Technology Data Exchange (ETDEWEB)

1993-03-15

The management of radioactive waste is one of the key issues in today`s discussions on nuclear energy, especially the long term disposal of high level radioactive wastes. The recycling of plutonium in liquid metal fast breeder reactors (LMFBRs) would allow `burning` of the associated extremely long life transuranic waste, particularly actinides, thus reducing the required isolation time for high level waste from tens of thousands of years to hundreds of years for fission products only. The International Working Group on Fast Reactors (IWGFR) decided to include the topic of actinide transmutation in liquid metal fast breeder reactors in its programme. The IAEA organized the Specialists Meeting on Use of Fast Breeder Reactors for Actinide Transmutation in Obninsk, Russian Federation, from 22 to 24 September 1992. The specialists agree that future progress in solving transmutation problems could be achieved by improvements in: Radiochemical partitioning and extraction of the actinides from the spent fuel (at least 98% for Np and Cm and 99.9% for Pu and Am isotopes); technological research and development on the design, fabrication and irradiation of the minor actinides (MAs) containing fuels; nuclear constants measurement and evaluation (selective cross-sections, fission fragments yields, delayed neutron parameters) especially for MA burners; demonstration of the feasibility of the safe and economic MA burner cores; knowledge of the impact of maximum tolerable amount of rare earths in americium containing fuels. Refs, figs and tabs.

A proposal for assessing study quality: Biomonitoring, Environmental Epidemiology, and Short-lived Chemicals (BEES-C) instrument

Science.gov (United States)

LaKind, Judy S.; Sobus, Jon R.; Goodman, Michael; Barr, Dana Boyd; Fürst, Peter; Albertini, Richard J.; Arbuckle, Tye E.; Schoeters, Greet; Tan, Yu-Mei; Teeguarden, Justin; Tornero-Velez, Rogelio; Weisel, Clifford P.

2015-01-01

The quality of exposure assessment is a major determinant of the overall quality of any environmental epidemiology study. The use of biomonitoring as a tool for assessing exposure to ubiquitous chemicals with short physiologic half-lives began relatively recently. These chemicals present several challenges, including their presence in analytical laboratories and sampling equipment, difficulty in establishing temporal order in cross-sectional studies, short- and long-term variability in exposures and biomarker concentrations, and a paucity of information on the number of measurements required for proper exposure classification. To date, the scientific community has not developed a set of systematic guidelines for designing, implementing and interpreting studies of short-lived chemicals that use biomonitoring as the exposure metric or for evaluating the quality of this type of research for WOE assessments or for peer review of grants or publications. We describe key issues that affect epidemiology studies using biomonitoring data on short-lived chemicals and propose a systematic instrument – the Biomonitoring, Environmental Epidemiology, and Short-lived Chemicals (BEES-C) instrument – for evaluating the quality of research proposals and studies that incorporate biomonitoring data on short-lived chemicals. Quality criteria for three areas considered fundamental to the evaluation of epidemiology studies that include biological measurements of short-lived chemicals are described: 1) biomarker selection and measurement, 2) study design and execution, and 3) general epidemiological study design considerations. We recognize that the development of an evaluative tool such as BEES-C is neither simple nor non-controversial. We hope and anticipate that the instrument will initiate further discussion/debate on this topic. PMID:25137624

Long-lived isotopes production in Pb-Bi target irradiated by high energy protons

Energy Technology Data Exchange (ETDEWEB)

Korovin, Y.A.; Konobeyev, A.Y.; Pereslavtsev, P.E. [Obninsk Institute of Nuclear Power Engineering, Obninsk (Russian Federation)

1995-10-01

Concentration of long-lived isotopes has been calculated for lead and lead-bismuth targets irradiated by protons with energy 0.4, 0.8, 1.0 and 1.6 GeV. The time of irradiation is equal from 1 month up to 2 years. The data libraries BROND, ADL and MENDL have been used to obtain the rate of nuclide transmutation. All calculations have been performed using the SNT code.

Precise and accurate isotope ratio measurements by ICP-MS.

Science.gov (United States)

Becker, J S; Dietze, H J

2000-09-01

The precise and accurate determination of isotope ratios by inductively coupled plasma mass spectrometry (ICP-MS) and laser ablation ICP-MS (LA-ICP-MS) is important for quite different application fields (e.g. for isotope ratio measurements of stable isotopes in nature, especially for the investigation of isotope variation in nature or age dating, for determining isotope ratios of radiogenic elements in the nuclear industry, quality assurance of fuel material, for reprocessing plants, nuclear material accounting and radioactive waste control, for tracer experiments using stable isotopes or long-lived radionuclides in biological or medical studies). Thermal ionization mass spectrometry (TIMS), which used to be the dominant analytical technique for precise isotope ratio measurements, is being increasingly replaced for isotope ratio measurements by ICP-MS due to its excellent sensitivity, precision and good accuracy. Instrumental progress in ICP-MS was achieved by the introduction of the collision cell interface in order to dissociate many disturbing argon-based molecular ions, thermalize the ions and neutralize the disturbing argon ions of plasma gas (Ar+). The application of the collision cell in ICP-QMS results in a higher ion transmission, improved sensitivity and better precision of isotope ratio measurements compared to quadrupole ICP-MS without the collision cell [e.g., for 235U/238U approximately 1 (10 microg x L(-1) uranium) 0.07% relative standard deviation (RSD) vs. 0.2% RSD in short-term measurements (n = 5)]. A significant instrumental improvement for ICP-MS is the multicollector device (MC-ICP-MS) in order to obtain a better precision of isotope ratio measurements (with a precision of up to 0.002%, RSD). CE- and HPLC-ICP-MS are used for the separation of isobaric interferences of long-lived radionuclides and stable isotopes by determination of spallation nuclide abundances in an irradiated tantalum target.

Production of radioactive ion beams and resonance ionization spectroscopy with the laser ion source at on-line isotope separator ISOLDE

International Nuclear Information System (INIS)

Fedosseev, V.N.; )

2005-01-01

Full text: The resonance ionisation laser ion source (RILIS) of the ISOLDE on-line isotope separation facility at CERN is based on the method of laser step-wise resonance ionisation of atoms in a hot metal cavity. Using the system of dye lasers pumped by copper vapour lasers the ion beams of many different metallic elements have been produced at ISOLDE with an ionization efficiency of up to 27%. The high selectivity of the resonance ionization is an important asset for the study of short-lived nuclides produced in targets bombarded by the proton beam of the CERN Booster accelerator. Radioactive ion beams of Be, Mg, Al, Mn, Ni, Cu, Zn, Ga, Ag, Cd, In, Sn, Sb, Tb, Yb, Tl, Pb and Bi have been generated with the RILIS. Setting the RILIS laser in the narrow line-width mode provides conditions for a high-resolution study of hyperfine structure and isotopic shifts of atomic lines for short-lived isotopes. The isomer selective ionization of Cu, Ag and Pb isotopes has been achieved by appropriate tuning of laser wavelengths

Rare Earth element (REE) incorporation in natural calcite. Upper limits for actinide uptake in a secondary phase

International Nuclear Information System (INIS)

Stipp, S.L.S.; Christensen, J.T.; Waight, T.E.; Lakshtanov, L.Z.; Baker, J.A.

2006-01-01

Secondary minerals have the potential to sequester escaped actinides in the event of a radioactive waste repository failure, but currently, data to define their maximum uptake capacity are generally lacking. To estimate a maximum limit for solid solution in calcite, we took advantage of the behavioural similarities of the 4f-orbital lanthanides with some of the 5f-orbital actinides and used rare Earth element (REE) concentration as an analogue. A suite of 65 calcite samples, mostly pure single crystals, was assembled from a range of geological settings, ages and locations and analysed by isotope dilution MC-ICP-MS (multiple-collector inductively-coupled plasma mass spectroscopy). All samples were shown to contain significant lanthanide concentrations. The highest were in calcite formed from hydrothermal solutions and from carbonatite magma. Maximum total mole fraction of REE was 4.72 x 10 -4 , which represents one substituted atom for about 2000 Ca sites. In comparison, synthetic calcite, precipitated at growth rates slow enough to insure solid solution formation, incorporated 7.5 x 10 -4 mole fraction Eu(III). For performance assessment, we propose that 7.5 mmole substitution/kg calcite should be considered the upper limit for actinide incorporation in secondary calcite. The largest source of uncertainty in this estimate results from extrapolating lanthanide data to actinides. However, the data offer confidence that for waters in the hydrothermal temperature range, such as in the near-field, or at groundwater temperatures, such as in the far-field, if calcite formation is favoured and actinides are present, those with behaviour like the trivalent lanthanides, especially Am 3+ and Cm 3+ , will be incorporated. REE are abundant and widely distributed, and they have remained in calcite for millions of years. Thus, one can be certain that incorporated actinides will also remain immobilised in calcite formed in fractures and pore spaces, as long as solution conditions

Molecular and electronic structure of actinide hexa-cyanoferrates; Structure moleculaire et electronique des hexacyanoferrates d'actinides

Energy Technology Data Exchange (ETDEWEB)

Bonhoure, I

2001-07-01

The goal of this work is to improve our knowledge on the actinide-ligand bond properties. To this end, the hexacyanoferrate entities have been used as pre-organized ligand. We have synthesized, using mild chemistry, the following series of complexes: An{sup IV}[Fe{sup II}(CN){sub 6}].xH{sub 2}O (An = Th, U, Np, Pu); Am{sup III}[Fe{sup III}(CN){sub 6}].xH{sub 2}O; Pu {sup III}[Co{sup III}(CN){sub 6}].xH{sub 2}O and K(H?)An{sup III}[Fe{sup II}(CN){sub 6}].xH{sub 2}O (An = Pu, Am). The metal oxidation states have been obtained thanks to the {nu}{sub CN}, stretching vibration and to the actinide L{sub III} absorption edge studies. As Prussian Blue, the An{sup IV}[Fe{sup II}(CN){sub 6}].xH{sub 2}O (An = Np, Pu) are class II of Robin and Day compounds. X-ray Diffraction has shown besides that these complexes crystallize in the P6{sub 3}/m space group, as the isomorphic LaKFe(CN){sub 6}.4H{sub 2}O complex used as structural model. The EXAFS oscillations at the iron K edge and at the An L{sub III} edge allowed to determine the An-N, An-O, Fe-C and Fe-N distances. The display of the multiple scattering paths for both edges explains the actinide contribution absence at the iron edge, whereas the iron signature is present at the actinide edge. We have shown that the actinide coordination sphere in actinides hexa-cyanoferrates is comparable to the one of lanthanides. However, the actinides typical behavior towards the lanthanides is brought to the fore by the An{sup IV} versus Ln{sup III} ions presence in this family of complexes. Contrarily to the 4f electrons, the 5f electrons influence the electronic properties of the compounds of this family. However, the gap between the An-N and Ln-N distances towards the corresponding metals ionic radii do not show any covalence bond evolution between the actinide and lanthanide series. (author)

Actinide chemistry in the far field

International Nuclear Information System (INIS)

Livens, F.R.; Morris, K.; Parkman, R.; Moyes, L.

1996-01-01

The environmental chemistry of the actinides is complicated due both to the extensive redox and coordination chemistry of the elements and also to the complexity of the reactive phases encountered in natural environments. In the far field, interactions with reactive surfaces, coatings and colloidal particles will play a crucial role in controlling actinide mobility. By virtue of both their abundance and reactivity; clays and other layer aluminosilicate minerals, hydrous oxides and organic matter (humic substances) are all identified as having the potential to react with actinide ions and some possible modes of interaction are described, together with experimental evidence for their occurrence. (author)

Detection of {sup 210}Po on filter papers 16 years after use for the collection of short-lived radon progeny in a room

Energy Technology Data Exchange (ETDEWEB)

Abu-Jarad, F. E-mail: falah.abujarad@aramco.com; Fazal-ur-Rehman

2003-07-01

Radon gas was allowed to accumulate in its radium source and then injected into a 36 m{sup 3} test room, resulting in an initial radon concentration of 15 kBq m{sup -3}. Filter papers were used to collect the short-lived radon progeny and thus to measure the Potential Alpha Energy Concentration (PAEC) in-situ in the year 1984 at different times and conditions according to the experimental design. The radon progeny collected on the filter papers were studied as a function of aerosol particle concentration ranging from 10{sup 2}-10{sup 5} particles cm{sup -3} in three different experiments. The highest aerosol particle concentration was generated by indoor cigarette smoking. Those filters were stored after the experiment, and were used after 16 years to study the activity of the radon long-lived alpha emitter progeny, {sup 210}Po (T{sub 1/2}=138 days). This isotope is separated from the short-lived progeny by {sup 210}Pb beta emitter with 22.3 years half-life. After 16 years' storage of these filters, each filter paper was sandwiched and wrapped between two CR-39 nuclear track detectors, to put the detectors in contact with the surfaces of different filters, for 337 days. Correlation between the PAEC measured using filter papers in the year 1984 and the activity of long-lived alpha emitter {sup 210}Po on the same filter papers measured in the year 2000 were studied. The results of the {sup 210}Po activity showed a very good correlation of 0.92 with the PAEC 16 years ago. The results also depict that the PAEC and {sup 210}Po activity in indoor air increased with the increase of aerosol particle concentration, which shows the attachment of short-lived radon progeny with the aerosol particles. The experiment proves that indoor cigarette smoking is a major source of aerosol particles carrying radon progeny and, thus, indoor cigarette smoking is an additional source of internal radiation hazard to the occupants whether smoker or non-smoker.

New spectrofluorometer with pulsed intensified photodiodes array for direct trace determination of actinides and lanthanides in solutions

International Nuclear Information System (INIS)

Decambox, P.; Kirsch, B.; Mauchien, P.; Moulin, C.

1989-01-01

Actinides and lanthanides in solution at very low level are determined by Time-Resolved Laser-Induced Spectrofluorometry (TRLIS) with pulsed intensified photodiodes array detection. Temporal resolution allows discrimination against short lifetime fluorescence and measurement of fluorescence lifetime in various matrices. The use of laser source leads to excitation selectivity and high sensitivity. Multichannel detection allows to cover the entire wavelength range of interest which leads to emission selectivity and rapidity. These different advantages are present in the newly commercialized spectrofluorometer FLUO 2001 together with specially analytical adapted software. The apparatus and performances obtained for several actinides and lanthanides are presented