Numerical analysis on flows in supersonic air intakes. Choonsoku kuki toriireguchi no nagare no suchi kaiseki

Energy Technology Data Exchange (ETDEWEB)

Shimada, T.; Tamura, N.; Sekino, N.; Tsujimura, N. (Nissan Motor Co. Ltd., Tokyo (Japan))

1992-06-25

By applying computational fluid dynamics (CFD) to a flow in the supersonic air intake of rocket, appropriateness of computational result was confirmed from a comparison with the wind tunnel test result. In order for the air intake type rocket to heighten the combustion efficiency of fuel and air, it is important to possibly minimize the total pressure loss of air which has been taken in and maintain the air flow rate. A numerical analysis was made through modeling the sectional shape of wind tunnel test body and analyzing the two-dimensional flow by Reynolds-averaged Navier-Stokes equations. The computational result of analysis coincided well with the pressure measurement result in wind tunnel test. Having elucidated the main factors of total pressure loss in a two-dimensionally curved flow passage, the CFD computation gave a possibility that the total pressure loss is considerably low against that passage if improved in shape. If simultaneously used with a characteristic curve method, the CFD computation made it possible to optimize the pressure recovery characteristics in the axially symmetric air intake. The CFD can be expected to be an effective method of designing the basic shape of supersonic air intake. 9 refs., 14 figs.

Numerical simulation on streaming potentials in a wellbore; Koseinai no ryudo den`i ni kansuru suchi simulation

Energy Technology Data Exchange (ETDEWEB)

Ikeda, N [Kyushu University, Fukuoka (Japan)

1996-05-01

This paper reports numerical computation of streaming potentials which are generated by transient pressure waves propagating the vicinity of wellbore wall immediately after a mud cake formed on the wellbore wall has been removed. One existing analysis solution on heat conduction was utilized upon changing the parameters in order to derive fluid pressure inside the ground bed. Calculations were carried out by using the existing three-dimensional finite difference method (partly re-written) based on the relationship constituted between the fluid pressure and the streaming potential. This paper presents results of calculating the streaming potentials in wellbores on models having wellbores filled with mud water in a cubic ground bed existing with ground bed water at saturation of 100%. The calculations have been conducted on the following cases: a case where permeability of the ground bed is small with the fluid under two conditions of low electric resistivity and high electric resistivity, a case where the permeability is large with the fluid under the above conditions, and a case where a small area of bore wall is covered with a rubber pad having high electric resistivity under a low electric resistivity condition. 8 refs., 5 figs.

On the validity of self-report assessment of cognitive abilities: Attentional control scale associations with cognitive performance, emotional adjustment, and personality.

Science.gov (United States)

Williams, Paula G; Rau, Holly K; Suchy, Yana; Thorgusen, Sommer R; Smith, Timothy W

2017-05-01

Individual differences in attentional control involve the ability to voluntarily direct, shift, and sustain attention. In studies of the role of attentional control in emotional adjustment, social relationships, and vulnerability to the effects of stress, self-report questionnaires are commonly used to measure this construct. Yet, convincing evidence of the association between self-report scales and actual cognitive performance has not been demonstrated. Across 2 independent samples, we examined associations between self-reported attentional control (Attentional Control Scale; ACS), self-reported emotional adjustment, Five-Factor Model personality traits (NEO Personality Inventory-Revised) and performance measures of attentional control. Study 1 examined behavioral performance on the Attention Network Test (ANT; Fan, McCandliss, Sommer, Raz, & Posner, 2002) and the Modified Switching Task (MST; Suchy & Kosson, 2006) in a large sample (n = 315) of healthy young adults. Study 2 (n = 78) examined behavioral performance on standardized neuropsychological tests of attention, including Conner's Continuous Performance Test-II and subtests from the Wechsler Adult Intelligence Scales, Third Edition (WAIS-III; Psychological Corporation, 1997) and Delis-Kaplan Executive Function System (D-KEFS; Delis, Kaplan, & Kramer, 2001). Results indicated that the ACS was largely unrelated to behavioral performance measures of attentional control but was significantly associated with emotional adjustment, neuroticism, and conscientiousness. These findings suggest that although self-reported attentional control may be a useful construct, researchers using the ACS should exercise caution in interpreting it as a proxy for actual cognitive ability or performance. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Conductive-cooled superconducting magnets and their applications; Chodendo wo mijikanishita reitoki chokurei hoshiki no chodendo jishaku

Energy Technology Data Exchange (ETDEWEB)

Kuriyama, T.; Sasaki, T.; Urata, M. [Toshiba Corp., Tokyo (Japan)

1998-01-01

This paper describes an outline of conductive-cooled superconducting magnets, magnetic regenerator materials, and their applications. This magnet is composed of a 4K cryocooler, superconducting current lead, heat shield plate, support, and vacuum vessel. Cooling of the conductive coil is initiated by the operation of 4K cryocooler. It takes two days to one week for the cooling-down time from room temperature to the given temperature. During that time, users need to do nothing for the superconducting magnet. When the superconducting coil is cooled to the given temperature, current is applied to the coil for excitation. Thus, magnetic field is formed. Paying attention to the magnetic anomaly specific heat accompanied with magnetic phase transition of magnetic substance at the extremely low temperature, Toshiba has developed a 4K cryocooler using magnetic regenerator material by utilizing magnetic specific heat. Oxide superconductor is adopted for the current lead which is used at the temperature level below 80K. Inflow of the heat can be suppressed in one-tenth of the conventional current lead. As a result, a small size device having easy operability without using liquid helium has been developed. 6 refs., 4 figs.

Survey o methods for secure connection to the internet; Internet tono anzenna setsuzoku hoshiki no genjo

Energy Technology Data Exchange (ETDEWEB)

Matsui, S

1994-04-01

This paper describes a study of a security method of protecting inside network computers against outside miscreants and unwelcome visitors and a control method when these computers are connected with the Internet. In the present Internet, a method to encipher all data cannot be used, so that it is necessary to utilize PEM (Privacy Enhanced Mail) capable of the encipherment and conversion of secret information. For preventing miscreant access by eavesdropping password, one-time password is effective. The most cost-effective method is a firewall system. This system lies between the outside and inside network. By limiting computers that directly communicate with the Internet, control is centralized and inside network Security is protected. If the security of firewall systems is strictly controlled under correct setting, security within the network can be secured even in open networks such as the Internet. 35 refs., 3 figs.

Vibration control of bridges and buildings hybrid system. Kyoryoter dot tatemono no shindo seigyo hybrid hoshiki

Energy Technology Data Exchange (ETDEWEB)

Tanida, K. (Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan))

1991-11-15

Multistory buildings, suspension bridges, and cable stayed bridges tend to become huge, and technology of controlling their vibration caused by strong winds and earthquakes is becoming an important subject for study. A description is made on a hybrid system which is a combination of the conventional passive system and active system, having merits of both of the systems. Verification test made using a model and an example of application to an actual bridge are introduced. This hybrid control system has been applied to the main tower of the cable stayed bridge on Route 12 of the Tokyo expressway. It is installed and in operation on the top of the tower to improve the workability, and can decrease the vibration of the tower caused by vortical excitation produced during the construction of the main tower. With the hybrid system, the actuator capacity can be reduced to about 1/5 for the similar damping performance to that of the active system with the same mass ratio. In addition, the weight of the equipment can be nearly halved in comparison with the passive system. Moreover, it has such a high safety characteristic as being used as a passive system when power supply is cut off because the controlling force of the system is smaller as compared with the active system. 2 refs., 11 figs.

Effects of electrical stimulation on fruit of lentinus edodes; Shiitake jinko kindoko ni taisuru denki shigeki ga kojittai hassei kosu ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Mitobe, K.; Sato, T.; Yoshimura, N. [Akita Univ. (Japan)] Suzuki, T. [Tohoku Electric Power Co. Ltd., Sendai (Japan)

1997-11-30

So far, the cultivation of Lentinus edodes is cultivated from material wood mainly, however, recently, artificial bed-blocks method has been used widely. The advantage of bed-block cultivation is to a short growing period and be possible to cultivate by a large scale facilities. Hereafter, it is thought that this growing method is used mainly. Before now, based on the experimental fact that abnormal fruiting of Lentinus edodes occurs due to lightening, the study on the effects of electrical stimulation was reported, however, the investigation on the effects of electrical stimulation on the artificial bed-bocks which is thought to come into wide use in future does not carry out until now. The purpose of this study is to investigate an increased yield of the Lentinus fruit-bodies grown on artificial bed-blocks that electrical stimuli were applied. Nineteen artificial bed-blocks were provided for each applied voltage condition; Control, 200V, 400V, 600V, for the AC. As a result of experiment, in the 600V condition, the total number of fruiting of Lentinus edodes was significantly increased as compared with other conditions. Especially, in the artificial bed-blocks that peak current was over 300 mA, the total number of fruiting was increased. 6 refs., 6figs.

Suppression of numerical dispersion using FD modified operators; Atarashii sabunho no enzanshi wo mochiita suchi bunsan no yokusei

Energy Technology Data Exchange (ETDEWEB)

Takeuchi, N; Geller, R [The University of Tokyo, Tokyo (Japan). Faculty of Science

1996-05-01

The author, et al., have developed a formal evaluation theory for errors in numerical solutions and derived on the basis of this theory the conditions that a modified error minimizing operator should satisfy. A modified operator was derived for a calculus of finite difference in the time domain making use of this error evaluation theory. In this study, a modified operator was derived for O (2, 2) in the calculus of finite difference in time, and the operator was used in the calculation for the old and new methods about 1-dimension inhomogeneous media, and the two were quantitatively compared in CPU time and calculation accuracy. The calculation used 500 space grids and 5000 time grids. With the ratio of the time grid gap and space grid gap are kept constant, both CPU time and calculation accuracy were in proportion to the square of the number of grids. It was found in view of the result that the new method, as compared with the old method, needs only approximately 1/20 of CPU time in performing calculations of the same precision and that it maintains calculation accuracy that is approximately 20 times higher in the said CPU time. 4 refs., 2 figs., 1 tab.

Development of WISH type transportable toilet with water circulation; WISH hoshiki kahangata junkan suiryushiki toire no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Amagai, B; Imaizumi, S [Leader Co. Ltd., Gunma (Japan); Ushiyama, I [Ashikaga Institute of Technology, Tochigi (Japan); Onai, Y

1997-11-25

Described herein are a proposed ``WISH (wind and solar hybrid) type portable toilet with water circulation,`` in which wind and solar power generation units are combined, and specifications of the toilet unit for 2 persons. It needs 2.2m{sup 3} of initial charge of water, which can be circulated by power stored in the battery unit in 2,600 to 3,000 cycles. Water can be kept at a pH level of 8 or lower, when circulated 200 times or less for a day. This number is increased to 500, when 2 units are installed. Dirty water is treated by an agent and circulated without being exhausted and without releasing offensive odor. Circulating water is recycled while being totally sterilized, whereas sludges are exhausted after being solidified by a powerful coagulant. The toilet unit is equipped with a pump (50W) and fan (75W). The solar unit generates power of at least 1.08Wh/day and the wind unit is equipped with a small-size generator having a rated capacity of 300W. The toilet units are commercialized and showing good results. 2 refs., 5 figs.

Numerical analysis of a horizontal axis wind turbine rotor with winglets; Winglet wo motsu suiheijiku fusha no suchi kaiseki

Energy Technology Data Exchange (ETDEWEB)

Hasegawa, Y.; Kikuyama, K.; Imamura, H. [Nagoya University, Nagoya (Japan)

1996-08-25

The objective of present study is to show the aerodynamic effectivity of a horizontal axis wind turbine rotor blades with winglets by means of numerical analysis. The winglet used in this study is considered to be an inclined extension of the blade. For the numerical analysis a vortex lattice method with a free wake model was used because the model can be fitted to an arbitrary blade shape and needs no empirical parameter about wake geometry. The calculations were made on the flow field in the rotor wake and the rotor performance, and the results were compared between the rotors with and without winglets. In order to examine the structural effects, the flap bending moment was also compared. The results shows that small installation angle of winglets is found to cause a larger increase in the power coefficient and a smaller increase in the flap bending moment than radially extended rotor blades. 11 refs., 13 figs., 1 tab.

List of participants at SIDE IV meeting, Tokyo, 27 November--1 December 2000

Science.gov (United States)

2001-12-01

Mark J Ablowitz, Vsevolod Adler, Mark Alber, Said Belmehdi, Marco Boiti, Claude Brezinski, R Bullough, Y M Chiang, Theodore Chihara, Peter A Clarkson, Robert Conte, Adam Doliwa, Vladimir Dorodnitsyn, Mitsuaki Eguchi, Claire Gilson, Basil Grammaticos, Valeri Gromak, Rod Halburd, Koji Hasegawa, Jarmo Hietarinta, Ryogo Hirota, Xing Biao Hu, M Idzumi, J Inoguchi, Hiroya Ishikara, Mourad Ismail, Shin Isojima, Kenichi Ito, Yoshiaki Itoh, Masashi Iwasaki, Klara Janglajew, Michio Jimbo, Nalini Joshi, Kenji Kajiwara, Saburo Kakei, Masaru Kamata, Satoshi Kamei, Rinat Kashaev, Shingo Kawai, Taeko Kimijima, K Kimura, Anatol Kirillov, Koichi Kondo, Boris Konopelchenko, Martin Kruskal, Atsuo Kuniba, Wataru Kunishima, Franklin Lambert, Serguei Leble, Decio Levi, Shigeru Maeda, Manuel Manas, Ken-Ichi Maruno, Tetsu Masuda, J Matsukidaira, Atsushi Matsumiya, Shigeki Matsutani, Yukitaka Minesaki, Mikio Murata, Micheline Musette, Atsushi Nagai, Katsuya Nakagawa, Atsushi Nakamula, Akira Nakamura, Yoshimasa Nakamura, Frank Nijhoff, J J C Nimmo, Katsuhiro Nishinari, Michitomo Nishizawa, A Nobe, Masatoshi Noumi, Yaeko Ohsaki, Yasuhiro Ohta, Kazuo Okamoto, Alexandre Orlov, Naoki Osada, Flora Pempinelli, Spiro Pyrlis, Reinout Quispel, Orlando Ragnisco, Alfred Ramani, Jean-Pierre Ramis, Andreas Ruffing, Simon Ruijsenaars, Satoru Saito, Noriko Saitoh, Hidetaka Sakai, Paulo Santini, Narimasa Sasa, Ryu Sasaki, Yoshikatsu Sasaki, Junkichi Satsuma, Sergei Sergeev, Nobuhiko Shinzawa, Evgueni Sklyanin, Juris Suris, Norio Suzuki, Yukiko Tagami, Katsuaki Takahashi, Daisuke Takahashi, Tomoyuki Takenawa, Yoshiro Takeyama, K M Tamizhmani, T Tamizhmani, Kouichi Toda, Morikatsu Toda, Tetsuji Tokihiro, Takayuki Tsuchida, Yohei Tsuchiya, Teruhisa Tsuda, Satoru Tsujimoto, Walter Van Assche, Claude Viallet, Luc Vinet, Shinsuke Watanabe, Yoshihida Watanabe, Ralph Willox, Pavel Winternitz, Yasuhiko Yamada, Yuji Yamada, Jin Yoneda, Haruo Yoshida, Katsuhiko Yoshida, Daisuke Yoshihara, Fumitaka Yura, J

Vitrectomy in patients over 90 years of age

Directory of Open Access Journals (Sweden)

Muto T

2016-01-01

Full Text Available Tetsuya Muto, Tomoyuki Ide, Makoto Chikuda, Shigeki Machida Department of Ophthalmology, Dokkyo Medical University Koshigaya Hospital, Koshigaya, Japan Purpose: The aim of this study was to evaluate vitrectomy procedures performed in patients over 90 years of age at the Dokkyo Medical University Koshigaya Hospital (Koshigaya, Japan.Patients and methods: Vitrectomies were performed in nine eyes of nine patients who were over 90 years of age between May 2010 and March 2015. Factors such as the underlying vitreoretinal disease, preoperative and postoperative best-corrected visual acuity (BCVA, surgical time, postoperative body position, need for a second surgery, systemic disease, and intraoperative changes in systemic conditions have been evaluated.Results: The most common cause of the underlying vitreoretinal disease was vitreous hemorrhage derived from age-related macular degeneration and posterior dislocation of the lens secondary to a posterior capsular rupture (two cases each. The mean values for the logarithm of the minimum angle of resolution BCVA were 2.15 preoperatively and 1.46 postoperatively (P=0.020, Wilcoxon signed-rank test. The mean surgical time was 109 minutes. Prone position was needed in two cases, and no second surgeries were needed. The most common cause of systemic disease was hypertension, which was found in six cases. Transient hypertension was found in two cases during surgery, and these patients were treated using intravenous calcium blocker injections.Conclusion: Patients over 90 years of age who underwent vitrectomy procedures did not have serious problems, except transient hypertension during surgery. The BCVA significantly improved. These results indicated that vitrectomies could be performed successfully in patients over 90 years of age. Keywords: vitrectomy, underlying vitreoretinal disease, transient hypertension

Horizontal vibration suppression method suitable for super-high-speed elevators; Chokosoku elevator ni tekishita kago yokoshindo yokusei hoshiki

Energy Technology Data Exchange (ETDEWEB)

Muto, N. [Hitachi, Ltd., Tokyo (Japan); Kagomiya, K.; Kurosawa, T.; Konya, M> ; Ando, T. [Hitachi Building System Co. Ltd., Tokyo (Japan)

1998-03-01

Horizontal vibrations of elevator cars mainly occur because a car swings as roller guides installed at corners of a car frame move on a winding guide rail at high speeds. Rider comfort in high speed elevators is worsened by these vibrations. Conventional active dampers suppressing horizontal vibrations using ac servo motors make cars heavier so driving power becomes larger, and they are not easily applied to existing elevators. An active damping control method suited to super-high-speed elevators is which can solve these problems. The method suppresses vibrations by generating only enough magnetic force needed to suppress them only when vibrations of the car franc are produced. The vibrations are detected using acceleration detectors and magnets installed on left and right sides of the car frame. A computer simulator was made to analyze phenomena of car vibrations and to verify effects of the proposed magnetic damping controller. It was found that the vibrations generated on the cabin floor were remarkably large when left and right sides at the upper and lower parts of the car frame were swung by sine waves with the same phase. The vibrations bad two resonant modes. Results obtained with the computer simulator and a full scale running simulator showed that the acceleration on the cabin floor, even at the resonant frequencies, could be reduced by the magnetic damping control to around 0.1m/s{sup 2} which would provide a comfortable ride. 10 refs., 14 figs.

Improvement in visual target detections and reaction time by auditory stimulation; Shikaku shigeki ga shikaku mokuhyo no kenshutsu to hanno jikan ni oyobosu kaizen koka

Energy Technology Data Exchange (ETDEWEB)

Mitobe, K.; Akiyama, T.; Yoshimura, N. [Akita University, Akita (Japan); Takahashi, M. [Hokkaido University, Sapporo (Japan)

1998-03-01

The purpose of this study was to investigate a traffic environment that can reduce traffic accidents of elder walker. We focused on the relationship between traffic accidents and elder person`s spatial attention. In this paper, an adolescent subject`s and an elder subject`s pointing movement to a visual target was measured in three conditions. Condition 1: Only target was presented. Condition 2: Auditory stimulation was added at a location the same distance from the center as that of the targets but in the opposite direction. Condition 3: Auditory stimulation was added at the same location as the target. The targets were placed in extra working space with the distance of 1.5 meter from a subject to the targets. In adolescent subjects, results showed that in Condition 3, latency was shorter and the error rate of pointing movements was lower than in the other conditions. In elder subjects, results showed that in all Conditions, ignore ratio to peripheral targets is higher than adolescent subjects. Nevertheless, in condition 3, ignore ratio was lower than in the other conditions. These results suggest that, it is possible to draw elder walker`s spatial attention and to control spatial attention by auditory stimulation. 13 refs., 6 figs., 1 tab.

'Development and introduction of ice water conveyance system and verification of low temperature blast system' for leveling off electric power load; Denryoku fuka heijunka wo misueta 'hyosui hanso hoshiki no kaihatsu donyu to teion sofu hoshiki no kensho'

Energy Technology Data Exchange (ETDEWEB)

Kuriyama, T. [Nikken Sekkei Ltd., Osaka (Japan)

1999-11-05

From the view point of the earth environment protection, energy-saving in the field of building air-conditioning has become increasingly important. On the other hand, the utilization of nighttime electric power is needed to ease the electric power supply and demand problem, and in this connection, a wider introduction of the ice heat storage system is recommended as one of the means to cope with such a problem. However, the ice heat storage system also has problems to be solved such as energy savability, and economy. Under such circumstances, various technical research and development efforts as well as evaluation thereof have been made centering around the 'technical development of the ice water conveyance system' and the 'evaluation of the low temperature blast system' for energy-saving, facility cost reduction and electric power load leveling off, and as a matter of fact these systems have been installed in actual buildings with useful results. (author)

Calculation of lobe mixer flow with reynolds stress model. Oryoku hoteishiki model ni yoru lobe mixer ryu no suchi keisan

Energy Technology Data Exchange (ETDEWEB)

Yamamoto, Makoto; Arakawa, Chuichi; Tagori, Tetsuo [Ishikawajima-Harima Heavy Industries, Co., Ltd., Tokyo (Japan) Univ. of Tokyo, Tokyo (Japan). Faculty of Engineering Univ. of Tsukuba, Tsukuba (Japan)

1990-02-25

It is considered that exhaust gas energy of turbofan engine is partly collected to realize the improvement of propulsion efficiency together with the reduction of noise appeared by the change in velocity distribution of exhaust gas flow. Then Lobe mixer was studied and its effectiveness was widely recognized, however the development of more realistic prediction method of exhaust nozzle system including Lobe mixer, is not completed yet. The stress equation model with low Reynolds Number which is easily used by the expansion of Launder Reece Rodi model in three dimension coordinate system was newly constructed. Applicability of the stress equation in more complicated flow field was greatly improved. While the above model was applied to Lobe mixer system, then the qualitative reproduction of mixing process accompanied with flow around Lobe and longitudinal eddy of core or bi-pass flow, was realized. There is room for improvement of pressure strain correlation term and behavior of Reynolds stress very close by wall surface in this model. 16 refs., 9 figs., 1 tab.

System to detect and protect a failure during start-up of pumping-up; Yosui shidochu no jikokenshutsu hogo hoshiki

Energy Technology Data Exchange (ETDEWEB)

Hagiwara, H. [Kansai Electric Power Co. Inc., Osaka (Japan)

1999-12-10

Development was made on a method to detect and protect a failure in a power generation motor operating at a rotation speed other than the rated speed, such as in start-up of pumping-up. Such a failure may not be detected from the ordinary frequency characteristics because the failure current due to short circuit or earth failure is lower than the rated frequency. An idea was conceived to detect flow of low frequency failure current on the armature side by detecting change in the field current being a phenomenal change in the armature current. To realize the idea, the simulation circuits of the parent and child motors of the power generation motors were modeled and verified. The following results were obtained from the verification of a three-phase short circuit failure: when the field current is constant, the failure current is nearly constant regardless of the operating frequency; the failure current flows into the field circuit; because the trajectory of the low frequency overcurrent in the main circuit flowing in case of operation in a low frequency zone presents the similar trajectory to that in 60-Hz operation, the failure may be detected from variation in the field current; and the protection activity after the failure detection is to release the excitation, and attenuate the failure current. (NEDO)

Investigation on vibrational dampers for cables of Tsurumi Tsubasa bridge; Tsurumi tsubasabashi no keburu seishin hoshiki ni kansuru jisho

Energy Technology Data Exchange (ETDEWEB)

Takano, H.; Ogasawara, M.; Shimosato, T. [Metropolitan Public Corp., Tokyo (Japan); Yamada, H. [Yokohama National Univ. (Japan)] Murakami, T. [NKK Corp., Tokyo (Japan). Applied Technology Research Center

1998-03-20

In a long cable-stayed bridge, countermeasure against wind induced vibration should be often taken at the same time together with the measure against angular bent phenomena (phenomena in which secondary bending stress is generated on the front of fixing socket by live load). The conventional countermeasure is a combined use of buffer rubber and dampers. This study points out problems in the conventional countermeasure on the application to the cables of the Tsurumi Tsubasa Bridge and combination of dampers and angular bending buffer device is examined. The result shows that a combined use of high-damping rubber and oil dampers enables installation of the dampers in a lower position while maintaining the performance and is excellent in the easiness in installation and maintenance and in aesthetic view. This system was applied to the Tsurumi Tsubasa Bridge and the effectiveness on damping and angular bending relaxation was confirmed through the model tests, and vibration tests and field observation on the cables. 9 refs., 20 figs., 7 tabs.

Refractive changes after lens-sparing vitrectomy for macular hole and epiretinal membrane

Directory of Open Access Journals (Sweden)

Muto T

2017-08-01

Full Text Available Tetsuya Muto,1 Tomoharu Nishimura,1 Takefumi Yamaguchi,2 Makoto Chikuda,1 Shigeki Machida1 1Department of Ophthalmology, Dokkyo Medical University Koshigaya Hospital, Koshigaya, Japan; 2Department of Ophthalmology, Tokyo Dental College Ichikawa General Hospital, Ichikawa, Japan Purpose: Cataract progression after lens-sparing vitrectomy might differ according to original posterior segment diseases. Our objective was to analyze the refractive values after lens-sparing vitrectomy for macular hole (MH and epiretinal membrane (ERM. Materials and methods: We reviewed the medical records of 25 MH patients (25 eyes and 23 ERM patients (23 eyes who underwent lens-sparing vitrectomy. Refractive changes in both groups were compared. All patients underwent 20-gauge three-port pars plana vitrectomy. Fluid–air exchange was performed during vitrectomy only in the MH group. The results were analyzed using the unpaired t-test, chi-square test, or Fisher exact probability test, and multivariate analysis. Results: There were no significant differences in the patient’s age (P=0.45. The myopia progression rate (D/month was higher in the MH group after surgery than that in the ERM group (P=0.035. MH group had more females (P=0.043, longer surgical time (P<0.001, and higher frequencies of surgical adjuvants use (triamcinolone acetonide, P=0.019; brilliant blue G, P<0.001. The myopia progression rate in the MH group (R=0.568, P<0.001 correlated with female gender. However, no correlation was observed between longer surgical time and the use of surgical adjuvants. Conclusion: The rate of myopia progression was higher in the MH group. Fluid–air exchange and gender may affect the rate of myopia progression. Keywords: cataract, vitrectomy, macular hole, epiretinal membrane

Review of research on remote sensing with digital map. Remote sensing to suchi chizu no ketsugo ni yoru kenkyu no shokai

Energy Technology Data Exchange (ETDEWEB)

Tanaka, S; Sugimura, T [Remote Sensing Technology Center of Japan, Tokyo (Japan)

1990-12-05

This paper describes the relationship between remote sensing and digital map. The relation between remote sensing and digital map is roughly classified into two kinds. One of them is utilization of remote sensing and digital map in combination to analyze phenomena, and the other is normalization of remote sensing data by use of digital map. For examples of utilizing remote sensing and digital map, there are the creation of a perspective image of ground scene from Landsat MSS data by use of a mesh type digital map of the orthogonal co-ordinates, and the creation of an image of the enviromental research along roads from satilite data by use of a vector type digital map. Furthermore, this paper introduces a procedure of correcting geographical strains by use of a digital map and converting a radar image to corrected plane image, and the use of a digital map in the global scale for the analysis of floods and other purposes. 20 refs., 5 figs., 1 tab.

FY1995 report on the analyses of functional living systems using magnetic stimulation and magnetic fields; 1995 nendo jiki shigeki oyobi kyojiba ni yoru seitai kino kaimei

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-05-01

The purpose of the project is to widen the understanding of the biological effects o magnetic fields and to search potential applications of biomagnetics to medical diagnosis and treatments. We developed a method of localized magnetic stimulation of the brain. By concentrating induced eddy currents on a target with a pair of opposing pulsed magnetic fields produced by a figure-eight coil, they were able to stimulate the human cortex within a 5 mm resolution. We studied the properties of diamagnetic water in static magnetic fields. The phenomenon that the surface of the water was pushed back by magnetic fields of higher gradients was observed. The behavior of oxygen dissolved in an aqueous solution under magnetic fields of up to 8T with a gradient of 50T/m was studied. For oxygen concentrations greater than 11 mg/l, a clear redistribution of dissolved oxygen was observed. Effects of strong magnetic fields on a process of dissolution of fibrin clots was studied. Fibrin polymers in water magneto-phoresically drifted in the direction of increasing magnetic fields, and dissolution of fibrin polymers by plasmin was accelerated. (NEDO)

3-D volume rendering visualization for calculated distributions of diesel spray; Diesel funmu kyodo suchi keisan kekka no sanjigen volume rendering hyoji

Energy Technology Data Exchange (ETDEWEB)

Yoshizaki, T; Imanishi, H; Nishida, K; Yamashita, H; Hiroyasu, H; Kaneda, K [Hiroshima University, Hiroshima (Japan)

1997-10-01

Three dimensional visualization technique based on volume rendering method has been developed in order to translate calculated results of diesel combustion simulation into realistically spray and flame images. This paper presents an overview of diesel combustion model which has been developed at Hiroshima University, a description of the three dimensional visualization technique, and some examples of spray and flame image generated by this visualization technique. 8 refs., 8 figs., 1 tab.

Wave fields simulation in difficult terrain using numerical grid method; Hyoko henka no aru chiiki deno suchi koshi wo mochiita hado simulation

Energy Technology Data Exchange (ETDEWEB)

Jung, W; Ogawa, T [Yokohama National University, Yokohama (Japan); Tamagawa, T; Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan)

1997-10-22

This paper describes that a high-accuracy simulation can be made on seismic exploration by using the numerical grid method. When applying a wave field simulation using the difference calculus to an area subjected to seismic exploration, a problem occurs as to how a boundary of the velocity structure including the ground surface should be dealt with. Simply applying grids to a boundary changing continuously makes accuracy of the simulation worse. The difference calculus using a numerical grid is a method to solve the problem by imaging a certain region into a rectangular region through use of variable conversion, which can impose the boundary condition more accurately. The wave field simulation was carried out on a simple two-layer inclined structure and a two-layer waved structure. It was revealed that amplitudes of direct waves and reflection waves are disturbed in the case where no numerical grid method is applied, and the amplitudes are more disperse in the reflection waves than those obtained by using the numerical grid method. 7 refs., 10 figs.

Improvement of D.I. diesel engine combustion using numerical simulation; Chokufun diesel kikan no nensho kaizen shuho. Suchi kaiseki ni yoru torikumi

Energy Technology Data Exchange (ETDEWEB)

Minami, T.; Adachi, T.; Isyii, Y. [Isuzu Motors Ltd., Tokyo (Japan)

1999-04-01

For the purpose of improving DI diesel engine combustion, it is important to predict air flow of intake and exhaust manifold, intake port flow, combustion chamber swirl and fuel spray combustion. This paper describes the application of numerical simulation to the engines, the analysis of phenomena and a problem of simulation model modification. (author)

Thermal sensation vote simulation on the aged for bus air conditioning; Koreisha wo koryoshita onkan suchi simulation no bus kucho eno tekiyo

Energy Technology Data Exchange (ETDEWEB)

Takeuchi, H; Nishijima, H; Kitada, M; Shinma, A [Denso Corp., Aichi (Japan)

1997-10-01

The Numbers of passengers on the aged of sight-seeing buses about 5 times bigger than those of car passengers, have been increasing gradually. The former paper of DENSO in 1994 introduces quantitative method, which simulates passenger heat amount given by sun light at various solar positions. At this time, this paper introduces quantitative method, which simulates passengers thermal sensation skin temperature and also heat amount given by sun light at various solar positions. 5 refs., 8 figs., 2 tabs.

Photovoltaic AC fusion converter (PVAC). Design consideration and experimental evaluation; Taiyoko hatsuden denryoku/shoyo denryoku kongo sochi no hoshiki to seino

Energy Technology Data Exchange (ETDEWEB)

Tsuchiya, Y. [Hachinohe National College of Technology, Aomori (Japan); Sakakibara, T. [Toyohashi University, of Technology, Aichi (Japan)

1997-11-25

The photovoltaic AC fusion converter (PVAC), of which cost reduction of the total system is possible, was developed. PVAC controls the supply of commercial power by preferentially supplying photovoltaic power to loads for realization of energy conservation. Further, setting the maximum output of solar cell less than the rated load, the system was made the one with no need of storage batteries. This system was realized in a hybrid of the conventional rectification technology and the stand-alone maximum power point tracking photovoltaic system technology. The solar cell input efficiency had been measured as 84% at maximum. Main losses are consumption power of power source, switching loss of inverter, and continuity loss of diode. Ninety-seven percent of the commercial power input efficiency was obtained. Main losses are consumption power of power source, continuity loss of diode bridge, and resistance loss of smoothing reactor. The effect of energy conservation by the use of PVAC was also admitted. 6 refs., 7 figs.

Regenerating method for thyristor converter used in AC inverter rolling stock; Koryu inverter sharyoyo thyristor converter no kaisei hoshiki no kento

Energy Technology Data Exchange (ETDEWEB)

Inarida, S.; Ito, S.; Nakamura, K. [Hitachi, Ltd., Tokyo (Japan)

1995-09-20

A thyristor converter is superior to GTO converter from a view point of weight and efficiency. Therefore, the thyristor converter is the best answer for AC inverter rolling stock, especially for commuter and interurban trains, in the next several years. For a thyristor converter, it is very important to prevent the commutative failure even when the category voltage decreases, in order to continue regenerating operation to sustain the brake torque. In a conventional system, a series resistance is inserted between the thyristor bridge and LC filter where the DC stage voltage is decreased enough to keep the regenerating power. The conventional thyristor enables regenerating braking in the whole operational region, but result in low power factor and efficiency. This paper proposes a new regenerating method to improve the power factor and efficiency, which keep regenerating power with no series resistance and higher DC stage voltage. Simulation results show the effectiveness of the method. 4 refs., 14 figs., 1 tab.

Survey of current technologies of security management for distributed information systems; Bunsangata joho system no security iji kanri hoshiki no genjo

Energy Technology Data Exchange (ETDEWEB)

Matsui, S [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1997-05-01

The latest situation of the security management for a distributed information system was examined and systematically summarized to indicate the management design in future. This paper describes the threat of the distributed information system to security, the risk for confidentiality, integrity, and availability due to the threat, and the measures to be taken. The basic technology of security management is classified into the `user certification to prevent an incorrect access` and the `encipherment to prevent data from being used incorrectly.` The technology for certification has been almost completed. It can be securely done using an expendable password or IC card system. In Internet, multiple enciphering technologies for constructing a virtual private network that can secure the almost the same security as for a private network can be used. In an electronic mail, the enciphering technology can also be used easily. The tool that manages the security of very many servers, clients, and networks is in the initial stage. 16 refs., 1 fig., 5 tabs.

Character of photovoltaic/thermal hybrid collector. Character analysis by numerical calculation; Taiyoko netsu hybrid collector no tokusei. Suchi keisan ni yoru tokusei kaiseki

Energy Technology Data Exchange (ETDEWEB)

Morita, Y; Iwawaki, T; Fujisawa, T; Tani, T [Science University of Tokyo, Tokyo (Japan)

1997-11-25

In order to investigate characteristics of photovoltaic (PV)/thermal hybrid collectors (PV/T{sub s}) operating under varying conditions, energy equilibrium equations have been developed for numerical calculation, and the calculated results were compared with the observed ones. The calculated characteristics are close to the observed ones, both for photoelectric conversion and heat collecting characteristics, demonstrating validity of these energy equations. It is found, by comparing characteristics of PV/T{sub A} (covered with glass) with those of PV/T{sub B} (not covered with glass), that these characteristics are greatly affected by glass cover. Maximum overall excergy levels attained are 13.29% with PV/T{sub A} and 11.48% with PV/T{sub B} under the conditions of solar radiation intensity H: 800W/m{sup 2}, ambient temperature: 20degC and wind velocity: 0.5m/s, where flow rates of heat medium are 2.0times10{sup -3} and 4.0times10{sup -3}kg/s, respectively. Thus, the PV/T{sub A} system has a higher maximum excergy efficiency than the PV/T{sub B} system. The PV/T{sub A} gives water of higher temperature, demonstrating that covering the system with glass increases maximum excergy efficiency and optimum temperature. 6 refs., 5 figs., 2 tabs.

Development of multi-filter spectroradiometry; Filter hoshiki ni yoru bunka hosharyo no keisoku hoho to sono supekutoru no hyogen hoho ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Miyake, Y; Aoshima, T; Minoda, T; Kato, T; Kondo, S [Eiko Instruments Trading Co. Ltd., Tokyo (Japan)

1996-10-27

Described in this paper is a technique of solar radiation spectroradiometry in which high-resolution wavelength computation adds to a multi-filter method. The solar spectrum upon entering the atmosphere is scattered and absorbed by parameter-constituting elements such as gas, aerosol, cloud particles, etc., and its spectral contour is complicatedly deformed relative to wavelength. Taking advantage of the fact that the scattering and absorbing characteristics of some of the elements are constant relative to wavelength, a simple equation was constructed to enable high-resolution spectrum measurement wavelength-wise, and this compensates for the limit in measurable wavelength that the conventional multi-filter method suffers from. The new method discussed here is not so expensive as the grating method thanks to the employment of filters, is capable of determining spectral radiation quantities with a precision of {plus_minus}5%, and is reduced in terms of the capacity of memory for data storage. The new method enables data collection under various atmospheric conditions that the four seasons present, which the difficult-to-apply and expensive spectroradiometer fails. It is expected that this method will find its use in collecting basic data for the designing of photovoltaic power generation systems, in the study of photochemical reaction in agriculture, and in collecting basic data for daylight lighting. 1 ref., 6 figs., 2 tabs.

Visualization of strong around motion calculated from the numerical simulation of Hyogo-ken Nanbu earthquake; Suchi simulation de miru Hyogoken nanbu jishin no kyoshindo

Energy Technology Data Exchange (ETDEWEB)

Furumura, T [Hokkaido Univ. of Education, Sapporo (Japan); Koketsu, K [The University of Tokyo, Tokyo (Japan). Earthquake Research Institute

1996-10-01

Hyogo-ken Nanbu earthquake with a focus in the Akashi straits has given huge earthquake damages in and around Awaji Island and Kobe City in 1995. It is clear that the basement structure, which is steeply deepened at Kobe City from Rokko Mountains towards the coast, and the focus under this related closely to the local generation of strong ground motion. Generation process of the strong ground motion was discussed using 2D and 3D numerical simulation methods. The 3D pseudospectral method was used for the calculation. Space of 51.2km{times}25.6km{times}25.6km was selected for the calculation. This space was discretized with the lattice interval of 200m. Consequently, it was found that the basement structure with a steeply deepened basement, soft and weak geological structure thickly deposited on the basement, and earthquake faults running under the boundary of base rock and sediments related greatly to the generation of strong ground motion. Numerical simulation can be expected to predict the strong ground motion by shallow earthquakes. 9 refs., 7 figs.

Numerical prediction with `DMDF` model of pack ice motion in the Okhotsk sea; DMDF model ni yoru Okhotsk kai ryuhyo undo no suchi yosoku

Energy Technology Data Exchange (ETDEWEB)

Matsuzawa, T.; Yamaguchi, H.; Suzuki, S.; Kato, H. [The University of Tokyo (Japan); Rheem, C. [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science

1996-12-31

A simulation was performed on pack ice motion in the Okhotsk Sea in winter by using the distributed mass/discrete floe (DMDF) method that carries out a dynamic numerical calculation of pack ice motion. Several kinds of cases were compared and calculated. As a result, effectiveness was verified on a DMDF model with boundary conditions which are relatively large in range and complex in nature. At the same time, it was possible to estimate part of the characteristics of pack ice motion in this sea area. The numerical calculation used the floe distribution on February 1, 1994 as the initial condition, and performed calculations on conditions until February 8 giving considerations on meteorological and hydrographic data. As a result, the calculation result showed the same movements as those in the observed ice conditions. If an ocean current is hypothesized steady, the calculation is affected more than necessarily by the ocean current, and it derives a result departed from reality. From these findings, it was elucidated that floe motions are governed mainly by wind; and in making a numerical modeling, a consideration including composition with the ocean current is necessary. Shear stress of wind has its acting direction displaced from the wind direction because of effect of the Corioli`s force. 6 refs., 13 figs., 2 tabs.

Kardiologiczne powikłania leczenia klozapiną

Directory of Open Access Journals (Sweden)

Piotr Wierzbiński

2015-07-01

Full Text Available Klozapina jest efektywnym lekiem przeciwpsychotycznym wprowadzanym w przypadkach schizofrenii lekoopornej. Stosowaniu klozapiny mogą towarzyszyć liczne działania niepożądane. Najczęściej opisuje się powikłania hematologiczne: neutropenię i agranulocytozę. Powikłania kardiologiczne są rzadkie, uważa się jednak, że częstość ich występowania jest niedoszacowana. Z tego względu klozapinę można włączyć jedynie po wykluczeniu chorób serca i zaburzeń rytmu na podstawie kompletnego wywiadu, pełnego badania przedmiotowego i elektrokardiogramu. Zapalenie mięśnia sercowego i kardiomiopatia są poważnymi powikłaniami stosowania klozapiny, potencjalnie zagrażającymi życiu pacjenta. Mechanizm powstawania tych zaburzeń nie jest do końca jasny, uznaje się, że wynikają one z nadwrażliwości na lek w wyniku reakcji alergicznej typu I zależnej od IgE. Symptomy są często niecharakterystyczne, mało specyficzne, mogą przypominać objawy grypopodobne. Najczęściej pojawiają się gorączka, suchy kaszel, bóle w klatce piersiowej i leukocytoza. Trzeba zwracać baczną uwagę na tachykardię spoczynkową, przede wszystkim w pierwszych dwóch miesiącach leczenia. Monitorowanie pacjenta pod kątem powikłań kardiologicznych w pierwszych miesiącach stosowania leku pozwala na wczesne rozpoznanie nieprawidłowości i uniknięcie poważnych następstw. W przypadku podejrzenia zapalenia mięśnia sercowego i kardiomiopatii klozapinę należy odstawić. Wszelkie nieprawidłowości w badaniu elektrokardiograficznym powinno się konsultować z kardiologiem. Jeśli wystąpią zapalenie mięśnia sercowego lub kardiomiopatia związana ze stosowaniem klozapiny, z uwagi na duże ryzyko kolejnych powikłań nie zaleca się ponownego włączania leku.

Efficacy and safety of febuxostat in elderly female patients

Directory of Open Access Journals (Sweden)

Mizuno T

2014-09-01

Full Text Available Tomohiro Mizuno,1,2 Takahiro Hayashi,3 Sayo Hikosaka,1 Yuka Shimabukuro,1 Maho Murase,1 Kazuo Takahashi,2 Hiroki Hayashi,2 Yukio Yuzawa,2 Tadashi Nagamatsu,1 Shigeki Yamada3 1Department of Analytical Pharmacology, Graduate School of Pharmacy, Meijo University, Nagoya, Japan; 2Department of Nephrology, School of Medicine, Fujita Health University, Toyoake, Japan; 3Department of Clinical Pharmacy, School of Medicine, Fujita Health University, Toyoake, Japan Background: Maintenance of low serum urate levels is important for the management of gout. Achieving the recommended serum urate levels of less than 6.0 mg/dL is difficult in elderly (65 years of age or older patients with renal impairment. Xanthine oxidase inhibitors allopurinol and febuxostat are used for this purpose. Although febuxostat had been shown to be efficacious in elderly patients, its safety and efficacy in elderly female patients with hyper­uricemia remain unclear.Objective: The aim of this study was to assess the efficacy and safety of febuxostat in elderly female patients.Methods: We studied a retrospective cohort study. The study included elderly Japanese patients (65 years of age or older who were treated with febuxostat at Fujita Health University Hospital from January 2012 to December 2013. The treatment goal was defined as achievement of serum urate levels of 6.0 mg/dL or lower within 16 weeks; this was the primary endpoint in the present study. Adverse events of febuxostat were defined as more than twofold increases in Common Terminology Criteria for adverse events scores from baseline. Results: We evaluated 82 patients treated with febuxostat during the observation period and classified them into male (n=53 and female (n=29 groups. The mean time to achievement of the treatment goal was significantly shorter in the female group (53 days than in the male group (71 days. There were no significant differences in adverse events between the 2 groups.Conclusion: Our

What is the true definition of a "Do-Not-Resuscitate" order? A Japanese perspective

Directory of Open Access Journals (Sweden)

Hiraoka E

2016-06-01

Full Text Available Eiji Hiraoka,1 Yosuke Homma,2 Yasuhiro Norisue,3 Takaki Naito,1 Yuko Kataoka,1 Osamu Hamada,1 Yo Den,1 Osamu Takahashi,4 Shigeki Fujitani3 1Department of Internal Medicine, 2Department of Emergency Medicine, 3Department of Critical Care Medicine, Tokyo Bay Urayasu Ichikawa Medical Center, Chiba, Japan; 4Department of Internal Medicine, St Luke’s International Hospital, Tokyo, Japan Background: Japan has no official guidelines for do-not-resuscitate (DNR orders. Therefore, we investigated the effect of DNR orders on physician decision making in relation to performing noncardiopulmonary resuscitation (CPR and CPR procedures.Methods: A case-scenario-based questionnaire that included a case of advanced cancer, a case of advanced dementia, and a case of nonadvanced heart failure was administered to physicians. The questions determined whether physicians would perform different non-CPR procedures and CPR procedures in the presence or absence of DNR orders. The number of non-CPR procedures each physician would perform and the number of physicians who would perform each non-CPR and CPR procedure in the absence and presence of DNR ocrders were compared. Physicians from three Japanese municipal acute care hospitals participated.Results: We analyzed 111 of 161 (69% questionnaires. Physicians would perform significantly fewer non-CPR procedures in the presence of DNR orders than in the absence of DNR orders for all three case scenarios (median [interquartile range] percentages: Case 1: 72% [45%–90%] vs 100% [90%–100%]; Case 2: 55% [36%–72%] vs 91% [63%–100%]; Case 3: 78% [55%–88%] vs 100% [88%–100%]. Fewer physicians would perform non-CPR and CPR procedures in the presence of DNR orders than in the absence of DNR orders. However, considerable numbers of physicians would perform electric shock treatment for ventricular fibrillation in the presence of DNR orders (Case 1: 26%; Case 2: 16%; Case 3: 20%.Conclusion: DNR orders affect physician

Resistance test of high-speed ship by means of attitude control method. Part 2; Shisei seigyo hoshiki ni yoru kosokutei no teiko shiken. 2

Energy Technology Data Exchange (ETDEWEB)

Hayashida, S [Nagasaki Institute of Applied Science, Nagasaki (Japan)

1996-04-10

The previous paper has proposed a resistance test method by controlling the attitude of a high-speed model ship using a personal computer without making a data base. For this method, the fluid force acting on the hull of model ship is measured, to change its attitude based on the measurement, and then, the fluid force is measured again, to change the attitude again. The traveling attitude is created by repeating this, to measure the force acting on the hull. Since the attitude is changed by calculating using the fluid force measured, various factors can be considered in the calculation process. For example, a test with an arbitrary displacement in an arbitrary position of center of gravity can be conducted in spite of actual displacement and position of center of gravity of the model ship. A test for a high-speed ship was conducted through this method, to obtain nearly satisfactory results compared with a usual resistance test. Occasionally, a lot of repetitions were required to satisfy the balancing condition of the force. In this study, the improvement of testing efficiency has been planned by modifying the analyzing program. 5 refs., 7 figs., 1 tab.

Numerical simulation of fuel sprays and combustion in a premixed lean diesel engine; Kihaku yokongo diesel kikan ni okeru nenryo funmu to nensho no suchi simulation

Energy Technology Data Exchange (ETDEWEB)

Miyamoto, T; Harada, A; Sasaki, S; Shimazaki, N; Hashizume, T; Akagawa, H; Tsujimura, K

1997-10-01

Fuel sprays and combustion in a direct injection Premixed lean Diesel Combustion (PREDIC) engine, which can make smokeless combustion with little NOx emission, is studied numerically. Numerical simulation was carried out by means of KIVA II based computer code with a combustion submodel. The combustion submodel describes the formation of combustible fuel vapor by turbulent mixing and four-step chemical reaction which includes low temperature oxidation. Comparison between computation and experiment shows qualitatively good agreement in terms of heat release rate and NO emission. Computational results indicate that the combustion is significantly influenced by fuel spray characteristics and injection timing to vary NO emission. 10 refs., 8 figs., 1 tab.

Three dimensional numerical modeling for investigation of fracture zone filled with water by borehole radar; Borehole radar ni yoru gansui hasaitai kenshutsu no sanjigen suchi modeling

Energy Technology Data Exchange (ETDEWEB)

Sanada, Y; Watanabe, T; Ashida, Y [Kyoto University, Kyoto (Japan); Hasegawa, K; Yabuuchi, S [Power Reactor and Nuclear Fuel Development Corp., Tokyo (Japan)

1997-05-27

Water bearing fracture zones existing in rock mass largely influence the underground water flow and dynamic property of rock mass. The detailed survey of the location and size of water bearing fracture zones is an important task in the fields such as civil engineering, environment and disaster prevention. Electromagnetic waves of high frequency zones can be grasped as a wave phenomenon, and the record obtained in the actual measurement is wave forms of time series. In the exploration using borehole radar, this water bearing fracture zone becomes the reflection surface, and also becomes a factor of damping in the transmitted wave. By examining changes which these give to the observed wave forms, therefore, water bearing fracture zones can be detected. This study made three dimensional numerical modeling using the time domain finite difference method, and obtained the same output as the observed wave form obtained using borehole radar. By using this program and changing each of the parameters such as frequency and resistivity in the homogeneous medium, changes of the wave forms were observed. Further, examples were shown of modeling of detection of water bearing fracture zones. 5 refs., 16 figs., 1 tab.

Application of low bitrate image coding to surveillance of electric power facilities. Part 1. Proposal of low bitrate coding for surveillance of electric power facilities and examination of facilities region extraction method; Denryoku setsubi kanshi eno tei rate fugoka hoshiki no tekiyo. 1. Setsubi kanshiyo fugoka hoshiki no teian to setsubi ryoiki chushutsuho no kento

Energy Technology Data Exchange (ETDEWEB)

Murata, H.; Ishino, R. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1996-03-01

Current status of low bitrate image coding has been investigated, and a low bitrate coding suitable for the surveillance of electric power facilities has been proposed, to extract its problems to be solved. For the conventional image coding, the waveform coding has been used by which the images are processed as signals. While, for the MPEG-4, a coding method with considering the image information has been proposed. For these coding methods, however, image information lacks details primarily, when lowering the bitrate. Accordingly, these methods can not be applied when the details in the images are important, such as in the case of surveillance of facilities. Then, the coding method has been proposed by expanding the partially detailed coding, and by separating constituent images of facilities, such as power cables and steel towers, designated by operators. It is the special feature of this method that the method can easily respond to the low bitrate and the detailed information can be conserved by using the structure extraction coding for the designated partial image which is generally processed by the low bitrate waveform coding. 29 refs., 17 figs., 1 tab.

Three dimensional numerical modeling for ground penetrating radar using finite difference time domain (FDTD) method; Jikan ryoiki yugen sabunho ni yoru chika radar no sanjigen suchi modeling

Energy Technology Data Exchange (ETDEWEB)

Sanada, Y; Ashida, Y; Sassa, K [Kyoto University, Kyoto (Japan)

1996-10-01

3-D numerical modeling by FDTD method was studied for ground penetrating radar. Radar radiates electromagnetic wave, and determines the existence and distance of objects by reflection wave. Ground penetrating radar uses the above functions for underground surveys, however, its resolution and velocity analysis accuracy are problems. In particular, propagation characteristics of electromagnetic wave in media such as heterogeneous and anisotropic soil and rock are essential. The behavior of electromagnetic wave in the ground could be precisely reproduced by 3-D numerical modeling using FDTD method. FDTD method makes precise analysis in time domain and electric and magnetic fields possible by sequentially calculating the difference equation of Maxwell`s equation. Because of the high calculation efficiency of FDTD method, more precise complicated analysis can be expected by using the latest advanced computers. The numerical model and calculation example are illustrated for surface type electromagnetic pulse ground penetrating radar assuming the survey of steel pipes of 1m deep. 4 refs., 3 figs., 1 tab.

Development of research activity supporting system. 2. Evaluation of desktop video conferencing; Kenkyu katsudo shien system no kaihatsu. 2. Enkaku kijo uchiawase hoshiki no jitsuyosei hyoka

Energy Technology Data Exchange (ETDEWEB)

Tsutsumi, F.; Hishitani, J.; Matsui, S. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1996-03-01

Desktop video conferencing (DVC) system and its software were investigated. A test system was actually constructed. Based on the test results, its practical advantage and disadvantage were illustrated. The DVC system was constructed using general LAN, and operation experiments were conducted, as to research activity. From the interview with participants and analysis of conversation history, advantage and disadvantage of this system were clarified. Performance of the trial system was examined using practical LAN, to compare with the performance of commercial systems. When using LAN, the same problems were given. It was found that the DVC system can not substitute for the conventional real face to face meeting, but it is suitable for some communication styles, for example free participation meeting or collaboration based on the same objective, which has been hard up to this time. In addition, software was made as trial, by which reservation of meeting, announcement, and calling can be carried out. 26 refs., 6 figs., 5 tabs.

Association of code status discussion with invasive procedures among advanced-stage cancer and noncancer patients

Directory of Open Access Journals (Sweden)

Sasaki A

2017-07-01

Full Text Available Akinori Sasaki,1 Eiji Hiraoka,1 Yosuke Homma,2 Osamu Takahashi,3 Yasuhiro Norisue,4 Koji Kawai,5 Shigeki Fujitani4 1Department of Internal Medicine, 2Department of Emergency Medicine, Tokyo Bay Urayasu Ichikawa Medical Center, Urayasu City, Chiba, 3Department of Internal Medicine, St. Luke’s International Hospital, Chuo-ku, Tokyo, 4Department of Critical Care Medicine, Tokyo Bay Urayasu Ichikawa Medical Center, Urayasu City, Chiba, 5Department of Gastroenterology, Ito Municipal Hospital, Ito City, Shizuoka, Japan Background: Code status discussion is associated with a decrease in invasive procedures among terminally ill cancer patients. We investigated the association between code status discussion on admission and incidence of invasive procedures, cardiopulmonary resuscitation (CPR, and opioid use among inpatients with advanced stages of cancer and noncancer diseases. Methods: We performed a retrospective cohort study in a single center, Ito Municipal Hospital, Japan. Participants were patients who were admitted to the Department of Internal Medicine between October 1, 2013 and August 30, 2015, with advanced-stage cancer and noncancer. We collected demographic data and inquired the presence or absence of code status discussion within 24 hours of admission and whether invasive procedures, including central venous catheter placement, intubation with mechanical ventilation, and CPR for cardiac arrest, and opioid treatment were performed. We investigated the factors associated with CPR events by using multivariate logistic regression analysis. Results: Among the total 232 patients, code status was discussed with 115 patients on admission, of which 114 (99.1% patients had do-not-resuscitate (DNR orders. The code status was not discussed with the remaining 117 patients on admission, of which 69 (59% patients had subsequent code status discussion with resultant DNR orders. Code status discussion on admission decreased the incidence of central venous

Optimization of performance and energy efficiency for series hybrid commuter-car; Series hybrid hoshiki no commuter car ni okeru doryoku seino to energy koritsu ni kansuru kosatsu

Energy Technology Data Exchange (ETDEWEB)

Hayashida, M; Narusawa, K [Traffic Safety and Nuisance Research Institute, Tokyo (Japan)

1997-10-01

The purpose of this study is to reveal a proper power system for a miniature vehicle called as `Commuter-car` for short trips in urban areas. Two types of simulated series hybrid commuter-cars were set on bench test systems. In order to have sufficient performance and energy saving, combination of electric motor and reduction gear. regenerative break efficiency and generator power supplying were considered by transient driving experiments. Further, estimation of primary energy consumption of the commuter-car was tried. 7 refs., 13 figs., 2 tabs.

A comparison of synchronized intermittent mandatory ventilation and pressure-regulated volume control ventilation in elderly patients with acute exacerbations of COPD and respiratory failure

Directory of Open Access Journals (Sweden)

Chang SC

2016-05-01

Full Text Available Suchi Chang,1 Jindong Shi,2 Cuiping Fu,1 Xu Wu,1 Shanqun Li1 1Department of Respiratory Medicine, Zhongshan Hospital, Fudan University, Shanghai, 2Department of Respiratory Medicine, The Fifth People’s Hospital of Shanghai, Fudan University, Shanghai, People’s Republic of China Background: COPD is the third leading cause of death worldwide. Acute exacerbations of COPD may cause respiratory failure, requiring intensive care unit admission and mechanical ventilation. Intensive care unit patients with acute exacerbations of COPD requiring mechanical ventilation have higher mortality rates than other hospitalized patients. Although mechanical ventilation is the most effective intervention for these conditions, invasive ventilation techniques have yielded variable effects. Objective: We evaluated pressure-regulated volume control (PRVC ventilation treatment efficacy and preventive effects on pulmonary barotrauma in elderly COPD patients with respiratory failure. Patients and methods: Thirty-nine intubated patients were divided into experimental and control groups and treated with the PRVC and synchronized intermittent mandatory ventilation – volume control methods, respectively. Vital signs, respiratory mechanics, and arterial blood gas analyses were monitored for 2–4 hours and 48 hours. Results: Both groups showed rapidly improved pH, partial pressure of oxygen (PaO2, and PaO2 per fraction of inspired O2 levels and lower partial pressure of carbon dioxide (PaCO2 levels. The pH and PaCO2 levels at 2–4 hours were lower and higher, respectively, in the test group than those in the control group (P<0.05 for both; after 48 hours, blood gas analyses showed no statistical difference in any marker (P>0.05. Vital signs during 2–4 hours and 48 hours of treatment showed no statistical difference in either group (P>0.05. The level of peak inspiratory pressure in the experimental group after mechanical ventilation for 2–4 hours and 48�

Różnorodność manifestacji klinicznych zakażeń Mycoplasma pneumoniae. Obserwacje kliniczne

Directory of Open Access Journals (Sweden)

Agnieszka Lipińska-Opałka

2013-12-01

Full Text Available Zakażenie Mycoplasma pneumoniae stanowi złożony problem kliniczny. Jego najczęstszą manifestacją jest tzw. aty‑ powe zapalenie płuc, charakteryzujące się łagodnym przebiegiem, umiarkowanie podwyższoną temperaturą ciała oraz obecnością niewielkich zmian osłuchowych nad polami płucnymi. Nasilenie objawów zależne jest od wieku pacjenta. U starszych dzieci choroba może przebiegać pod postacią śródmiąższowego lub płatowego zapalenia płuc, czasem z zapaleniem opłucnej, a stany gorączkowe mogą osiągać wyższe wartości. Wspólnym i najbardziej charakterystycznym objawem zakażenia jest suchy, męczący kaszel, utrzymujący się od 4 do 6 tygodni. Poza ukła‑ dem oddechowym zakażenie M. pneumoniae może manifestować się objawami z niemal każdego narządu ludzkiego organizmu. Obserwuje się powikłania neurologiczne, sercowo-naczyniowe, ze strony przewodu pokarmowego, kostno-stawowe i skórne. Mnogość manifestacji klinicznych wynika z faktu, że obok bezpośredniego uszkadzania komórek nabłonkowych bakteria ma zdolność do stymulowania procesów autoimmunologicznych i prozakrzepowych. Diagnostyka zakażenia opiera się głównie na metodach serologicznych. W leczeniu stosuje się makrolidy, a czas trwania terapii wynosi minimum 2 tygodnie. W artykule przedstawiliśmy dwa przypadki zakażenia M. pneumoniae, znacznie różniące się przebiegiem klinicznym. U pierwszego pacjenta główną manifestacją zakażenia było zapale‑ nie płuc, które długo przebiegało z wysoką gorączką, zapaleniem opłucnej oraz obecnością licznych zmian osłu‑ chowych nad polami płucnymi. Dodatkowo występowały objawy ze strony przewodu pokarmowego pod postacią wymiotów i intensywnych bólów brzucha. Z kolei u drugiego pacjenta w przebiegu świeżego zakażenia M. pneumoniae i w obecności innych czynników ryzyka doszło do rozwoju masywnej zakrzepicy żył głębokich.

Investigations on sail force by full scale measurement and numerical calculation. Part 1. Steady sailing performance; Sail ryutairyoku ni kansuru jissen shiken to suchi keisan. 1. Teijo hanso seino

Energy Technology Data Exchange (ETDEWEB)

Masuyama, Y.; Fukasawa, T. [Kanazawa Institute of Technology, Ishikawa (Japan); Kitazaki, T. [DMW Corp., Tokyo (Japan)

1997-06-01

Sailing forces are measured with a 10.3m long full-scale sailing boat, equipped with a sail force dynamometer, CCD camera for sail shape measurement and an instrument for detecting sailing conditions of the hull, in order to obtain highly reliable performance data of a sailing yacht. The vortex lattice method is used for step-by-step numerical calculations, and the results are compared with the observed ones. The test results clearly show performance changing with slight changes in relative wind directions and sail shapes, which are not clearly obtained by the traditional wind tunnel tests. The calculated results, although deviating from the observed ones to some extent, well represent trends of performance changing with wind directions and sail shapes. In particular, changed performance caused by slight changes in draft at the main sail is clearly demonstrated. The numerical calculation is considered to be useful for searching for sail trim conditions. 17 refs., 18 figs., 1 tab.

Study of numerical simulations concerning the performance of antennas used for automobile wireless communications; Jidosha no musen tsushin ni okeru antenna seino hyoka no tame no suchi simulation no ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Sueyoshi, M; Yano, T; Noda, Y; Goto, H [Honda Lock Mfg. Co. Ltd., Tokyo (Japan)

1997-10-01

Automobiles and communication technologies will be more closely related with each other in the advanced intelligence society. Anti-theft security systems apply those technologies, where antenna performance is one of the key elements. This is a study of numerical simulations of the performance of those vehicle antennas. 2 refs., 2 figs.

Discussion on boundary conditions for simplified numerical simulation of swirl velocity in a cylinder of engine; Engine nai swirl no kan`i suchi simulation ni okeru kyokai joken no kento

Energy Technology Data Exchange (ETDEWEB)

Matsumoto, K; Tasaka, H; Tan, H [Miyazaki University, Miyazaki (Japan)

1997-10-01

A simplified and quantitative simulation to calculate a swirl velocity in a cylinder with short time and low cost was offered by one of the authors. But the discussion on boundary conditions for the simulation was not enough. In this paper, measurements of diminution of the swirl velocity in a vessel packed with a fluid and simulations corresponding to the measurements were carried out varying aspect ratio of the vessel. From the measurement and calculating results, boundary conditions were obtained. The validity of the obtained boundary conditions was discussed and the adequate boundary conditions were determined. 4 refs., 6 figs., 2 tabs.

Report on achievements in fiscal 1975 in Sunshine Project. Feasibility study on a volcanic electric power generation system; 1975 nendo kazan hatsuden hoshiki ni kansuru feasibility study seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-03-01

The survey and study activities in the second year for the feasibility study (FS) on a volcanic electric power generation system consist of the following three parts: Part I, the case study on Satsuma Iojima Island, Part II, case study on Toyohane Mine, and Part III, FS on remote measurement of volcanic fume. The Part I, which has been performed subsequently from the previous fiscal year, has carried out the following surveys at different sites: meteorological, hydrological and underground water surveys, natural earthquake survey, fume and hot spring surveys (on-shore and off-shore), heat dissipation survey, tide level survey, underground structure survey (electric exploration), natural environment (vegetation) survey, thermal image survey, and social environment survey. The part II has begun surveys starting this fiscal year, because a considerable number of high temperature portions are already known to exist in the gallery, where there is a possibility of dry and hot rocks to exist without relationship with the present volcanic activities. This fiscal year has carried out mainly putting into order and analyzing the materials having been obtained in association with mine developments. The part III has been performed succeeding the 'FS on technologies to measure volcanic fume energy' done by the Japan Mining Industry Association. Some experiments were also executed at the Aso volcano. (NEDO)

Construction of Tai Lam tunnel under a Build, Operate and Transfer (BOT) scheme in Hong Kong; BOT hoshiki ni yoru Hong Kong root 3 (Tai Lam tunnel) kensetsu koji

Energy Technology Data Exchange (ETDEWEB)

Hayashi, K.; Endo, S. [Nishimatsu Construction Co. Ltd., Tokyo (Japan)

1998-01-01

Hongkong Route 3 construction under the BOT scheme (covering the basic plan, design, and construction, and the management of the completed tunnel as a private, toll facility) is described. The new route aims at dealing with aggravating traffic conditions as part of the major highway network joining Hongkong and Guanzhou, China proper. It is a dual three lane system, consisting of a 3.7km-long road tunnel, a 1.5km-long southern approach, and a 6.3km-long northern approach. Geologically speaking, the tunnel section as a whole is on a relatively hard and stable basement made of fine-grain granite and granitic diorite. Also introduced in this report are the project-executing organization and the flow of tendering under the BOT scheme. Since the shortening of the construction time is quite important in the 30-year BOT franchise period, rapid boring technologies were introduced into tunnel excavation. The 5.6m long-hole blasting enabled a maximum monthly progress of 460m. For the assurance of high boring accuracy and cycle time reduction, a fully automatic boring machine was adopted for speedy positioning and marking. An emulsion-type explosive was used, which can be pump-fed under pressure, for shortening the charging time. 5 figs.

Report on achievements in fiscal 1975 in Sunshine Project. Feasibility study on a volcanic electric power generation system; 1975 nendo kazan hatsuden hoshiki ni kansuru feasibility study seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-03-01

The survey and study activities in the second year for the feasibility study (FS) on a volcanic electric power generation system consist of the following three parts: Part I, the case study on Satsuma Iojima Island, Part II, case study on Toyohane Mine, and Part III, FS on remote measurement of volcanic fume. The Part I, which has been performed subsequently from the previous fiscal year, has carried out the following surveys at different sites: meteorological, hydrological and underground water surveys, natural earthquake survey, fume and hot spring surveys (on-shore and off-shore), heat dissipation survey, tide level survey, underground structure survey (electric exploration), natural environment (vegetation) survey, thermal image survey, and social environment survey. The part II has begun surveys starting this fiscal year, because a considerable number of high temperature portions are already known to exist in the gallery, where there is a possibility of dry and hot rocks to exist without relationship with the present volcanic activities. This fiscal year has carried out mainly putting into order and analyzing the materials having been obtained in association with mine developments. The part III has been performed succeeding the 'FS on technologies to measure volcanic fume energy' done by the Japan Mining Industry Association. Some experiments were also executed at the Aso volcano. (NEDO)

Condensation of refrigerants in horizontal microfin tubes. Numerical analysis of heat transfer for annular flow regime; Reibai no microfin tsuki suihei kannai gyoshuku. Kanjoryu ryoiki ni okeru netsudentatsu no suchi kaiseki

Energy Technology Data Exchange (ETDEWEB)

Nozu, S [Okayama Prefectural University, Okayama (Japan); Honda, H [Kyushu University, Fukuoka (Japan). Institute of Advanced Material Study

1998-07-25

A method for predicting the local heat transfer coefficient is presented for film condensation of vapor in a spirally grooved horizontal microfin-tube. Based on the flow observation study performed by the present authors, film flow model between fins in the annular flow regime is proposed. For the fin surface, laminar condensate film controlled by the combined effects of vapor shear and surface tension forces is analyzed. While, in the groove, thick condensate film driven by the vapor shear force is taken into consideration. A parameter which accounts for the transition from annular- to stratified flow regimes is also derived. The present and previous local heat transfer data for fluorocarbon refrigerants in the annular flow regime are found by the present numerical analysis to have a mean absolute deviation of 15.1 percent. 12 refs., 10 figs., 2 tabs.

Output characteristic of photovoltaic module on different installing conditions. Comparison with calculated value and measured value; Secchi joken no kotonaru taiyo denchi module no shutsuryoku tokusei. Suchi kaiseki to jissokuchi tono hikaku

Energy Technology Data Exchange (ETDEWEB)

Sasaki, T.; Morita, Y.; Iwawaki, H.; Fujisawa, T.; Tani, T. [Science University of Tokyo, Tokyo (Japan)

1997-11-25

The paper studied output characteristics of photovoltaic modules different in installation conditions on the basis of the energy balance state. In the study, an energy balance equation was constructed for insolation intensity, heat losses from PV surface/back, and output, in order to calculate cell temperatures in each installation condition. A comparative study was made between calculated results and measured data obtained on the top of the school building. The results indicated the following: The thickness of thermal boundary layer became approximately 27mm at insolation intensity of 800 W/m{sup 2}, ambient air temperature of 25degC, and wind velocity of 0.5m/s. When widening air gap from 20mm to 40mm, the cell temperature decreased 4degC, and the output increased 1.6%. In the case of installing photovoltaic modules on the roof considering the relation between the air gap in the heat balance state and the thickness of thermal boundary layer, heat from PV back was released outside the air gap if widening the air gap to more than 30-40mm. The type with a heat insulating material on the panel back decreased in output from other types. 5 refs., 7 figs., 4 tabs.

Waste treatment of ships. Change in understanding of wastes and trend of waste treatment systems; Senjo no haikibutsu shori. 1. Haikibutsu ni taisuru ninshiki no henka to shori hoshiki no doko

Energy Technology Data Exchange (ETDEWEB)

Inatomi, M. [Hitachi Zosen Corp., Osaka (Japan)

1996-07-25

This paper explains treatment of wastes produced in ships. Wastes produced in ships should be essentially treated on ships. Since storage and transport of difficult-to-treat wastes to harbor for land treatment is expensive, wastes produced in ships are treated on ships as much as possible. Combustibles such as waste oil, plastics, paper and wood fiber waste are treated by incinerator. Food waste is dumped into the sea after crushing by disposer. Excrement and urine are dumped into the sea through a waste water treatment plant. Oil content in oily bilge is burned after heating and vapor separation. Food waste is temporarily stored in ships because its dumping along the coast and into harbor is impossible. Kitchen refuse decomposer utilizing bacteria was proposed for ships. Press for used cans and crushing/thermal compaction/storage equipment for plastics were also put on the market. The primary regulation on diesel engine exhaust gas may be cleared by improvement of engine bodies. 1 ref., 1 fig., 1 tab.

Application of a temperature selective heat storage tank to a solar system. Part 3. Solar heat collecting system; Ondo sentaku chikunetsuso no solar system eno tekiyo. 3. Shunetsu hoshiki ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Kamiya, Y [Kanto Gakuin University, Yokohama (Japan); Kanayama, K [Kitami Institute of Technology, Hokkaido (Japan)

1996-10-27

The tank system and tank-less system when the temperature selective heat storage tank is applied to a solar system were considered. In the tank system, the simulation shows that the annual supplementary heat consumption is reduced as the tank capacity becomes lower. The most suitable operating time set for determining the reference time is about five hours in winter and about nine hours in summer. The annual operating time is about 6.5 hours. In the tank-less system, the most suitable minimum flow rate per solar collector area of a heating medium in Tokyo and its districts is 10 L/hm{sup 2} for both three-step flow control and constant flow control. The tank-less system is slightly lower in annual supplementary heat consumption than the tank system. For the three-step flow control, a change in the annual supplementary heat consumption is lower than that in the minimum flow rate. For the constant flow control, however, the annual supplementary heat consumption rapidly increases when the flow rate more decreases than the optimum value. The number of pump start/stop counts for the three-step flow control is less than two times as high as for the constant flow control. 4 refs., 6 figs., 1 tab.

Heat and mass transfer in a reforming catalyst bed. Analytical prediction of distributions in the catalyst bed; Kaishitsu shokubaiso ni okeru netsu oyobi busshitsu ido. Suchi kaiseki ni yoru sonai bunpu no yosoku

Energy Technology Data Exchange (ETDEWEB)

Usami, Y [Tokyo Electric Power Co. Inc., Tokyo (Japan); Fukusako, S; Yamada, M [Hokkaido University, Sapporo (Japan)

2000-01-25

Heat and mass transfer characteristics within a reforming catalyst bed have been analytically investigated. A numerical analysis was carried out in a two-dimensional steady-state model of reforming catalyst layer. Reforming tube was filled with catalyst and the tube wall was uniformly heated, a mixture of steam and methane was reformed through the catalyst bed. Predicted temperature, formed gas composition, methane conversion rate, and heat transfer coefficient distributions in the catalyst layer showed good agreement with experimental data. The effects of space velocity, steam carbon molar ratio, and wall temperature on the heat transfer coefficient were analytically presented. From temperature and composition distributions simulated by two-dimensional analysis, the effects of these factors above mentioned and diffusion on the transport phenomena were qualitatively predicted. (author)

Achievement report for fiscal 1999 on project for supporting the formation of energy/environmental technology verification project. International joint verification research project (Use of combined binary power generation systems at new geothermal fields on Mindoro Island, the Philippines, and comparison with conventional power generation systems); 1999 nendo Philippines koku Mindoro to no shinki chinetsutai ni okeru combined binary hatsuden hoshiki no tekiyo seika hokokusho. Conventional hatsuden hoshiki tono hikaku kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Concerning the Manito Lowlands geothermal field and the Montelago geothermal field where the systems are to be newly installed, the geothermal reservoir characteristics are assessed, and cost effectiveness is compared between different power generating systems. According to the investigations conducted into the two geothermal fields in the past, they are supposed to have geothermal potentials of the medium grade. Chemical analyses are conducted anew on this occasion into the hot spring water and fumarole gas, and the MT (magnetotelluric) method is implemented for the survey of reservoir distribution. It is now expected that approximately 20MWe will be exploited from each of the two geothermal fields. The power generation systems studied are the single flash type and double flash type for the conventional power generation system, and the cascade type, bottoming type, and two-phase binary type for the combined binary power generation system. As the result, it is concluded that the double flash type or two-phase binary type will be advantageous to the Manito Lowlands geothermal field, and the double flash type or bottoming type or two-phase binary type will be advantageous to the Montelago geothermal field. (NEDO)

Three-dimensional analysis of internal flow characteristics in the injection nozzle tip of direct-injection diesel engines; Sanjigen suchi kaiseki ni yoru DI diesel kikan no nenryo funsha nozzle nai ryudo tokusei no kaimei

Energy Technology Data Exchange (ETDEWEB)

Ogawa, H; Matsui, Y; Kimura, S [Nissan Motor Co. Ltd. Tokyo (Japan)

1997-10-01

To reduce the exhaust emissions and fuel consumption of direct-injection diesel engines, it is essential to optimize the fuel injection equipment closely related to combustion and emission characteristics. In this study, three-dimensional computation has been applied to investigate the effects of the injection nozzle specifications (e.g., sac volume, round shape at the inlet of the nozzle hole) and needle tip deviation on internal flow characteristics. The computational results revealed that the effects of the nozzle specifications and needle tip deviation with a smaller needle lift on internal flow characteristics and a general approach to optimize the injection nozzle specifications were obtained. 3 refs., 10 figs., 1 tab.

Methods for constructing time synchronous networks. Part 1. Consideration and experiment of time synchronizing functions and devices; Zenkei jikoku dokimo no kosei shuho. 1. Jikoku doki hoshiki no kino kento to jikkenteki kensho

Energy Technology Data Exchange (ETDEWEB)

Serizawa, Y.; Kitamura, K.; Myojin, M.; Shimizu, K. [Central Research Institute of Electric Power Industry, Tokyo (Japan); Nenohi, H.; Morimitsu, M.; Masui, O.; Matsushima, T. [NEC Corp., Tokyo (Japan)

1996-03-01

For the purpose of the back-up protection of regional power line system and the protection and control of accident influence, construction methods of time synchronizing network have been investigated. This paper proposes a method suitable for business power communication. For the synchronization between stations, transmission delay and its fluctuation have to be measured accurately by transmitting time signals between stations. Based on the observed delay values, the function of time correction (phase synchronizing control) of synchronized station is required. A mutual type synchronizing method was proposed, to which a sampling synchronization method of carrier relay system for transmission line protection was applied. In this method, transmission of time signals and measurement of delays are mutually conducted between stations, and phases of independent transmitters of the both stations are controlled so as to be equivalent. This method is characterized by the suppression of delays with fluctuation in the same direction of two-way transmission. For the transmission of time signals, two types of synchronizing devices were employed, i.e., synchronous and asynchronous manners. In the former, frequency synchronous network of SDH (synchronous digital hierarchy) was synchronized. In the latter, a carrier relay device was utilized independent of frequency synchronous network. It was expected that a synchronous network with an order of {mu}s can be constructed. 11 refs., 21 figs., 3 tabs.

2012 geothermal energy congress. Proceedings

International Nuclear Information System (INIS)

2012-01-01

); (15) GEOGRUND*: Transfer of the TCS process into the borehole (David Sauer); (16) 'Heat-in-place-density' - An example for the evaluation of the geothermal potential in Saarland (Hagen Deckert); (17) Experiences of the acidity stimulation of geothermal aquifers and plants (Markus Wolfgramm); (18) Geothermal Atlas for the depiction of possible utilization competitions between CCS and deep geothermy - Methodology and results (E. Suchi); (19) Development of a cooling system for geothermal bore hole probes (Benedict Holbein); (20) Geothermal energy in the context of international radiation protection recommendations (Sebastian Feige); (21) Innovative treatment of groundwater as a condition of an efficient air conditioning in buildings by utilization of near-surface geothermal energy (C. Meyer); (22) Preparation of planning maps for the utilization of near-surface geothermal energy with geo-physical methods (Reinhard Kirsch); (23) Deep geothermal probe Heubach - Progress of the project and facility planning by using an application example (David Kuntz); (24) Realistic numeric models for the simulation of potential geothermal reservoirs in the north-west German basin (Dorothea Reyer); (25) Monobore tracer test sensitivity compared with crack parameters and rock parameter: Lection Horstberg (Iulia Ghergut); (26) Infrastructure of fault zones in red sandstone of the Upper Rhine basin - Digestion analogue studies (Johanna F. Bauer); (27) Characterization of fault zones in shell limestone of the Upper Rhine basin - Digestion analogue studies (Silke Meier).

Study on a small diesel engine with direct injection impinging distribution spray combustion system. Optimum of injection system and combustion chamber; Shototsu kakusan hoshiki kogata diesel kikan ni kansuru kenkyu. Funshakei to nenshoshitsu no saitekika

Energy Technology Data Exchange (ETDEWEB)

Fujita, K; Kato, S; Saito, T [Kanazawa Institute of Technology, Ishikawa (Japan); Tanabe, H [Gunma University, Gunma (Japan)

1997-10-01

This study is concerned with a small bore (93mm) diesel engine using impinged fuel spray, named OSKA system. The higher rate of injection show lower smoke emission with higher NOx Emission. The exhaust emission and performance were investigated under different compression ratio with higher rate of injection. The experimental results show that this OSKA system is capable for reducing the smoke emission without the deterioration of NOx emission and fuel consumption compared with the conventional DI diesel engine. 5 refs., 8 figs., 3 tabs.

Thermal boundary condition effects on forced convection heat transfer. Application of a numerical solution of an adjoint problem; Kyosei tairyu netsudentatsu mondai ni okeru netsuteki kyokai joken no eikyo. Zuihan mondai no suchi kai wo mochiita kosatsu

Energy Technology Data Exchange (ETDEWEB)

Momose, K.; Saso, K.; Kimoto, H. [Osaka University, Osaka (Japan). Faculty of Engineering Science

1997-11-25

We propose a numerical solution for the adjoint operator of a forced convection heat transfer problem to evaluate mean heat transfer characteristics under arbitrary thermal conditions. Using the numerical solutions of the adjoint problems under Dirichlet and Neumann conditions, both of which can be computed using a conventional CFD code, the influence function of the local surface temperature on the total heat transfer and that of the local surface heat flux on the mean surface temperature are obtained. As a result, the total heat fluxes for arbitrary surface temperature distributions and the mean surface temperatures for arbitrary surface heat flux distributions can be calculated using these influence functions. The influence functions for a circular cylinder and for an in-line square rod array are presented. 14 refs., 9 figs., 1 tab.

Verification test for an electric vehicle using capacitor-battery series connection for battery load levelling; Denchi no fuka heijunka no tame no kyapashita to denchi no chokuretsu setsuzoku hoshiki wo saiyoshita denki jidosha no jissho shiken

Energy Technology Data Exchange (ETDEWEB)

Miyaoka, K.; Takehara, J.; Kato, S. [Chugoku Electric Power Co. Inc., Hiroshima (Japan)

1998-03-25

For the prolongation of the distance that an electric vehicle (EV) can cover on a single charge and of the service life of the EV battery unit, a system is developed, in which the battery unit and the capacitor unit are connected in series for the levelling-off of battery peak loads, and the system is tested aboard a running real vehicle. Installed on the real vehicle is a battery unit that is a series connection of 20 12V-38Ah seal-type lead-acid batteries, each battery consisting of two cells connected in parallel. Driving the vehicle is a DC brushless motor capable of a maximum operation of 9000rpm. Also installed is a capacitor unit that is a parallel connection of 40 2.3V-1800F capacitors, each capacitor consisting of two capacitors connected in parallel. Findings are described below. In a 0-400m acceleration test, 22.5 seconds is recorded with the capacitor unit in operation, meaning an improvement of 0.7 seconds. The maximum speed remains unchanged at 110km/h, which agrees with the pre-calculated value. Although the battery peak load reduction rate in a 15-mode drive pattern marks 23%, the distances covered on a single charge in this drive pattern turn out to be almost the same whether the capacitor unit is in operation or not. 3 refs., 15 figs., 3 tabs.

Natural convection and radiation heat transfer in a vertical porous layer with a hexagonal honeycomb core. 1st Report. Numerical analysis; Honeycomb core de shikirareta enchoku takoshitsu sonai no shizen tairyu - fukusha fukugo netsu dentatsu. 1. Suchi kaiseki

Energy Technology Data Exchange (ETDEWEB)

Yamaguchi, Y; Asako, Y [Tokyo Metropolitan Univ., Tokyo (Japan). Faculty of Technology; Faghri, M [University of Rhode Island, Kingston, RI (United States)

1997-06-25

Combined heat transfer characteristics are obtained numerically for three-dimensional natural convection and thermal radiation in a long and wide vertical porous layer with a hexagonal honeycomb core. The porous layer is assumed to be both homogeneous and isotropic. The pure Darcy law for the fluid flow and Rosseland`s approximation for the radiation are employed. The numerical methodology is based on an algebraic coordinate transformation technique and the transformed governing equations are solved using the SIMPLE algorithm. The effect of radiation on the beat transfer characteristics is investigated in a wide range of radiation numbers and temperature ratios, for two Darcy-Rayleigh number values (Ra*=100, 1000), and for a fixed aspect ratio of H/L=1. The results are presented in the form of combined and convection heat transfer coefficients, and are compared with the corresponding values for pure natural convection. 7 refs., 12 figs., 1 tab.

Numerical simulation of growth of flames formed in two-dimensional mixing layer. 2nd Report. Effect of dilution of fuel; Nijigen kongo sonai ni keiseisareta kaen no seicho ni kansuru suchi simulation. 2. Nenryo no kishaku ni yoru eikyo

Energy Technology Data Exchange (ETDEWEB)

Noda, S [Toyohashi University of Technology, Aichi (Japan); Hashimoto, K [Sumitomo Metal Industries, Ltd., Osaka (Japan); Nakajima, T [Kobe University, Kobe (Japan). Faculty of Engineering

1994-07-25

The effect of fuel dilution on growth of flames formed in 2-D mixing layers was studied by numerical simulation. The methane mass fraction of fuel was adjusted to 1.0, 0.3 and 0.2 through dilution by nitrogen, while the oxygen mass fraction of an oxidizer was fixed at 0.27. Flame structure was complicated due to the flows separated by flame at the leading edge of flames, and three peaks of the second Damkohler number were observed. Fuel dilution by nitrogen caused blow-off of flames, and the mixing ratio of the fuel and oxidizer at the leading edge of flames was essential to blow-off of diffused flames. In the case where vortices were observed in a flow field, the first Damkohler number was important which was determined by the hydrodynamic characteristic time of coherent vortices and the chemical characteristic time of flame propagation based on the mixing ratio of the fuel and oxidizer at the leading edge of flames. The diffused flames were elongated by shearing force, and an exothermic reaction was suppressed and a flame stabilization decreased with a decrease in second Damkohler number. 10 refs., 9 figs., 1 tab.

'Research and development of research information infrastructure'. Achievement report on development of parallel processing software technology for discrete value solving methods; Kenkyu joho kiban kenkyu kaihatsu seika hokokusho. Risanka suchi kaiho no tame no heiretsu shori software gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-09-01

Research and development has been performed on a general purpose parallel processing software that can be utilized for value solving methods, such as the finite element method, finite volume method and finite difference method. The achievements of the research and development may be summarized as follows: this parallel platform is parallelized in the concept of the domain division method for the elements (calculation cells), and is applicable to any of the finite element method, finite volume method and finite difference method; a researcher who has developed a program can easily perform the parallelization work to have the parallelizing performance displayed; the platform can be utilized in agreement with several parallel levels that are required by the user; with regard to the parallelization efficiency in large-size problems, it has become possible to execute at an efficiency of higher than 70% for the solver parts by using 32 processors of SR8000 at the computation center of the Agency of Industrial Science and Technology; the rigidity matrix preparing part shows an efficiency close to 100%W; and the developed parallel platform is under continued evaluation at the Machine Technology Research Institute and the Material Engineering Research Institute. (NEDO)

Numerical simulation of growth of flames formed in a two-dimensional mixing layer. 3rd Report. Flame instability induced by vortices; Nijigen kongo sonai ni keiseisareta kaen no seicho ni kansuru suchi simulation. 3. Uzu ni yotte reikisareru kaen no fuanteisei

Energy Technology Data Exchange (ETDEWEB)

Noda, S; Makino, H [Toyohashi University of Technology, Aichi (Japan); Nakajima, T [Kobe University, Kobe (Japan). Faculty of Engineering

1996-03-25

The flame instability induced by large vortices has been studied numerically. The numerical simulation is concerned with an unstable, two-dimensional, two-stream, spatially developing, confined, reacting shear layer. The behavior just after ignition is related to the flame instability which is affected strongly by large vortices in the mixing layer. Although flames are basically stable due to the balance between the burning velocity and the stream velocity, it is revealed that the leading edge is exposed under the strain in the mixing layer, and the flame becomes instable. Moreover, a method is also proposed to improve the flame stability by increasing the oxygen concentration in the oxidizer. 13 refs., 6 figs., 2 tabs.

Reports on 1979 result of Sunshine Project. Testing research for detailed design of solar thermal power generation plant (tower converging method); 1979 nendo taiyonetsu hatsuden plant (tower shuko hoshiki) no shosai sekkei no tame no shiken kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-03-31

This report briefly describes first, in the summary of the results, the contents of the research results of the year with the outcome as the central point. Then, it explains in detail, in the contents of the research, the substance of each research item, results, their examination contents, and future research subjects. The objective of the research is, for the purpose of technically seeking the cost performance of a solar thermal power generation plant, (1) to develop equipment constituting the plant and (2) to develop a pilot plant having an electrical output of about 1,000kW at the peak by the tower converging method. The research results were as follows. (1) In the confirming test of a heliostat test unit, the final conclusion was obtained of the wind resistance calculated value by the wind tunnel test of the heliostat; the design materials of the assembly jigs were obtained; the data of the operation forecast was obtained in a tracking test; and a sensor was developed for the tracking instrumentation. (2) In the confirming test of the improved absorbing surface/mirror, the improvement/trial production including the manufacturing method was carried out as the absorbing surface for the actual unit. (3) In the heat collecting test, steam generation and a loop control test were performed. (4) The plant system was analyzed, with data obtained for the operating method. (NEDO)

Proposal of an efficient operation method about order processing sequence and allocating goods to racks in the automatic picking system; Jido picking system ni okeru shohin no tanawaritsuke to chumon shori junjo no koritsuka un`yo hoshiki no teian

Energy Technology Data Exchange (ETDEWEB)

Ono, T.; Kagami, A.; Kosaka, M. [Hitachi Ltd., Tokyo (Japan)

1997-07-05

The material distribution center is a facility to store the goods from a factory and to prepare to ship the goods in response to order from retail store. Recently, with multiplication of consumption market, multi-variety and less-amount of the goods, multi-frequency of delivery and time saving form order to delivery are required. As picking work to prepare the stored goods for each customer requires specially many man-hours out of the works in this center, time saving of working becomes an important problem. In this paper, for an object of the automatic picking system constructed by plural equipments and to execute picking of small goods for each order, the following two operation methods were proposed: (1) To define shelf sharing of the goods so that the picking requirement numbers for each picking hand may be uniform as well as possible in response to order distribution for each goods, and (2) to define treating sequence of order so as not to generate large difference in order treating times among each treating hand on operation in parallel. These operation methods were confirmed their total treating time saving by some experiments using actual ordered data. 7 refs., 8 figs., 6 tabs.

Reports on 1977 result of Sunshine Project. R and D on high calorie gas manufacturing technology (molten salt/lime slurry bath gasification method); 1977 nendo kokarori gas seizo gijutsu no kenkyu kaihatsu seika hokokusho. Yoyuen sekkai slurry yo gas ka hoshiki

Energy Technology Data Exchange (ETDEWEB)

NONE

1978-03-31

The following results were obtained by fundamental studies on molten salt/lime slurry bath gasification method. A comparison between a gasification process in a literature and the subject process shows the characteristics as follows. It is necessary to withdraw a high temperature molten salt slurry from under pressurization to atmospheric pressure and to separate only the ash content from other components; however, a large burden of this operation is a problem. In addition, CaO reacts with a part of the ash, making complete recovery of CaO difficult. From these two reasons, the subject gasification process has disadvantage, compared with the fluidized-bed process, against coal that contains much ash content. The gasification process, however, has the following advantage. It can reduce oxygen usage. It is unaffected by the grain size and caking of coal. The reaction rate of CaO in carbonation is several times greater in molten salt than in a fluidized bed. The heat of reaction of CaO for carbonation is an exothermic reaction and can supply several tens of percentages of the heat of reaction in coal gasification. The desulfurization effect of CaO is great. Molten salt has a catalytic effect, making particularly the reaction rate of methanization several times greater. (NEDO)

Fiscal 1974 Sunshine Project result report. R and D on solar heat power generation system (R and D on curved reflector light collection system); 1974 nendo taiyonetsu hatsuden system no kenkyu kaihatsu seika hokokusho. kyokumen shuko hoshiki system no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-05-30

This report composed of 6 parts summarizes the fiscal 1974 Sunshine Project research result on the solar heat power generation system with a curved reflector light collection system. Part 1 outlines the research target, research result and research system. Part 2 describes each research item in detail. This part on system and hardware researches is composed of (1) study on 1,000kW system, (2) development of plane/parabolic reflector light collection equipment, (3) development of parabolic reflector light collection equipment, (4) development of selective transparent membrane and selective absorption surface, and (5) study on heat storage equipment and heat exchange equipment. Part 3 describes the future R and D plan for every year focusing the fiscal 1975 R and D plan. Part 4 describes various cooperative activities with other research groups such as various committees related to the Sunshine Project, universities and Electrotechnical Laboratory. Part 5 describes several patents produced during this R and D. Part 6 summarizes the results on this R and D. (NEDO)

FY 1977 Annual report on Sunshine Project results. Experimental research for detailed designs of tower light-collection type solar thermal power plant; 1977 nendo taiyonetsu hatsuden plant (tower shuko hoshiki) no shosai sekkei no tame no shiken kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1978-03-31

This project is aimed at pursuing technical and economic possibilities of solar thermal power plant by development of devices for a tower light-collecting type solar thermal power plant (in particular, heliostat, heat absorber and heat storage device) and materials therefor through the basic tests, and tests using a 10 kW heat collector and construction, on a trial basis, of a large-scale model plant with a commercial heliostat, and by planning to construct a 1,000 kW-class pilot plant for generating peak-shaving power using these devices. The major achievements in the FY1977 are summarized. The system analysis estimates annual power production possibly reaching 547,600 kWH. The heat-collecting test plant records a heat-collecting efficiency of 50 to 70% for collected heat quantity of 50 kW or more. The heliostat test confirms that the GL type is more favorable than the XY type. The heat absorber, which is a 1/3 model of the commercial device, is tested for its heat releasing performance, producing the quantitative released heat data. The heat transfer characteristics are investigated for the regenerative heat exchanger when the phase changes occur simultaneously on both molten salt and water sides. The mirror is exposure-tested in the field test for 1 year, to collect the data. (NEDO)

Fiscal 1974 Sunshine Project result report. R and D on solar heat power generation system (R and D on tower solar collection system); 1974 nendo taiyonetsu hatsuden system no kenkyu kaihatsu seika hokokusho. Tower shuko hoshiki system no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-05-29

This report summarizes the fiscal 1974 research result on the solar heat power generation system with a tower light collection system. This system receives solar radiation energy by reflector group, and concentrates solar energy reflected by each reflector on the heat absorber mounted on the top of the tower. A ratio of the whole reflector group area to the receiving area of the heat absorber is called a concentration factor. The heat absorber converts concentrated dense radiation energy to thermal energy, and transfers heated thermal medium to the bottom of the tower to supply solar heat to a thermal plant after appropriate treatment. Based on the above basic idea, study was made on the total system and each subsystem, and some problems on component equipment and materials were extracted. After solving these problems and improving the whole system accuracy, these results are put to practical use for design and operation of an actual pilot plant. The main research items are as follows: feasibility study, simulation, element study, preparation of a 10kWT test equipment, and planning of a 1,000kW class pilot plant. (NEDO)

Sunshine Program for fiscal 1979. Designs and drawings for tower concentration type solar thermal electric power generation pilot plant construction (Volume 1 of 2); 1979 nendo taiyonetsu hatsuden (tower shuko hoshiki) pilot plant no seisaku sekkei. Sekkei tosho (1/2)

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-03-01

The pilot plant outputs 1000kWe. Under an automated operation program, 2 operators per shift take care of the whole plant (with one operator on patrol). Daily startup and stop is automatic in principle. The system stops its operation in principle when the computer is down, with accessories to be manually stopped. Warnings are dealt with all by the computer. A safety sequence is organized independent from the computer. The operators interfere with the system for the manipulation of subsystems and adjustment functions. With the plant in normal operation, the computer system logs data, monitors warnings, and the plant is under control of an analog control unit. For the activation of the automatic startup/stop function, the operators have to choose a mode of operation. The above-named document covers, furthermore, the data processing function of the automatic operating system, automatic startup/stop program, hardware, automatic startup/stop table, and a general flow chart describing the automatic startup/stop train. (NEDO)

FY 1979 Annual report on Sunshine Project results. Fabrication designs for a solar thermal power pilot plant with curved-surface type light-collecting system (Part 1); 1979 nendo taiyonetsu hatsuden (kyokumen shuko hoshiki) seika hokokusho. 1. Pilot plant no seisaku ksekkei

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-03-01

This report describes basic and fabrication design specifications for operation and control of a solar thermal power pilot plant with curved-surface type light-collecting system, centered by computer for the plant control. Chapter I, basic fabrication design specifications, describes the general, design specifications and design scope. Chapter II, system design specifications, describes plant operating manuals, computer-aided plant control, computer-aided data processing for plant control, and analysis of system characteristics. Chapter III, hardware specifications, describes the specifications of central processing unit (CPU), fixed head disc device (M DISC), console inputting/outputting device, process inputting/outputting device, logging typewriter, process display (CRT), cassette magnetic tape device, operator console, relay cubicle, power source panel for computer, and hardware lists. Chapter IV, attachments, contains the following documents: plant operating manuals, operation procedure flow charts, control processing specifications, control function specifications, APS console function specifications, computer inputting/outputting point list, and data processing function instructions. The attachment documents are also contained in Part 2 of JN0040512. (NEDO)

Fiscal 1976 Sunshine Project result report. R and D on solar heat power generation system (R and D on tower solar collection system); 1976 nendo taiyonetsu hatsuden system no kenkyu kaihatsu seika hokokusho. Tower shuko hoshiki system no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-05-27

This report describes the fiscal 1976 research result on tower solar collection system for solar heat power generation systems, and summarizes main specifications of the subsystem, equipment and control of the 1,000kW pilot plant. Based on daily and monthly long-time simulation, various programs were prepared for power generation, heat storage and operation rate of equipment, and real arrangements for total simulation were made. The output fluctuation rate less than 1%/min was obtained by studying a control system flexible for drastic fluctuation of solar radiation using the newly prepared dynamic characteristic equation for a steam loop. 10kW solar collection test was carried out using a pancake type heat absorber. Practical basic analysis was made on a heliostat driving system. A cavity type heat absorber was adopted in consideration of cost, operability and heat discharge. Based on thermal characteristics of a heat storage type heat exchanger using molten salt as heat medium, basic experiment was made on a compact latent heat type heat exchanger. Basic studies were also made on reflector, selective absorption surface and heat storage material. (NEDO)

Attempt to measure the temperature, pressure and particle velocity of pyrocastic surge with penetrator-type gauge. ; Airdropping experiment at Unzen volcano. Penetrator hoshiki ni yoru kasai surge no ondo, atsuryoku, ryushi sokudo sokutei no kokoromi. ; Unzendake ni okeru toka jikken

Energy Technology Data Exchange (ETDEWEB)

Taniguchi, H. (Science Education Institute of Osaka Prefecture, Osaka (Japan)); Kamata, K.; Sange, K. (Kobe University, Kobe (Japan). Faculty of Science); Nakada, S. (Kyushu University, Fukuoka (Japan). Faculty of Science); Kamata, H. (Geological Survey of Japan, Osaka Office, Osaka (Japan))

1992-08-01

This paper describes development of a penetrator intended of measuring temperatures, pressures, and particle velocities of air blasts and pyroclastic surges occurring in volcanos, and its airdropping experiment. This device forms a spear with a total length of 150 cm to 160 cm disposed with wings at the tail, and a stopper to prevent the spear from penetrating into ground deeper than 60 cm. The device for measuring temperatures suspends metal pieces of 16 kinds in total including such metals as lead and tin, and such alloys as eutectic solders and type lead to enable measuring a temperature range from 100[degree]C to 810[degree]C . The device for measuring pressures consists of a square pipe with a length little shorter than one meter, twisted to 22.5[degree] at three locations, each of the 16 faces made from the twisting being attached with two blast meters (using lead and copper foils, serving also as particle velocity meters). Twelve prototype devices have been dropped (not having been recovered yet) on five points of the east side slope of Mt. Unzen using a helicopter. 5 refs., 3 figs.

FY 1979 Annual report on Sunshine Project results. Fabrication designs for a solar thermal power pilot plant with curved-surface type light-collecting system (Part 2); 1979 nendo taiyonetsu hatsuden (kyokumen shuko hoshiki) seika hokokusho. 2. Pilot plant no seisaku sekkei

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-03-01

Part 1 of this report (JN0040511) describes basic and fabrication design specifications for operation and control of a solar thermal power pilot plant with curved-surface type light-collecting system, centered by computer for the plant control. Part 2 follows Part 1, which describes basic fabrication design specifications (Chapter I), system design specifications (Chapter II), hardware specifications (Chapter III) and attachments (Chapter IV), to contain the other attachments: daily processing specifications, computer-aided processing function specifications, operator request function specifications, summary data collection function specifications, basic structures of the software systems, basic specifications for computer inputting/outputting, failure display panel drawings, COD/channel base dimension drawings, console inputting/outputting dimension drawings, T/W disc dimension drawings, viewer external dimension drawings, cassette MT structure dimension drawings, operator console panel drawings, power source panel dimension drawings, program specifications GFC, 4 subroutine specifications GFC (R sub), table list, table structure drawings, and analysis of system characteristics (light- and heat-collection system simulation). (NEDO)

Fiscal 1976 Sunshine Project result report. R and D on solar heat power generation system (R and D on curved reflector light collection system); 1976 nendo taiyonetsu hatsuden system no kenkyu kaihatsu seika hokokusho. Kyokumen shuko hoshiki system no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-03-01

As a part of Sunshine Project, study was made on the solar heat power generation system using a solar collection system composed of plane and curved reflectors. In fiscal 1976, study was made on plant characteristics and plant operation by using system simulation program, and the concept design of the system was promoted. The reflectance of the plane reflector was improved up to 0.92 by remodeling the prototype collector fabricated in last fiscal year, and the prototype test facility of full-scale reflectors for 1,000kW solar power plant was prepared to obtain design data for large reflectors. The prototype heat collection loop control equipment which was prepared to simulate control of plant operation conditions according to solar radiation fluctuation, succeeded in prediction of solar radiation fluctuation within nearly 30min. New study was also made on a system using both accumulator and molten salt heat storage equipment, and each proper capacity for power plants was determined. In addition, high-temperature vapor generation for 2 hours was achieved by the prototype heat storage equipment using KCl-LiCl molten salt. (NEDO)

Study on transmitting mechanisms for CVT using a dry hybrid belt. Numerical simulation of transmitting forces and pulley thrusts at steady and transitional states; Kanshiki fukugo belt wo mochiita CVT ni kansuru kenkyu. Teijo oyobi hensokuji ni okeru dentatsuryoku to pulley suiryoku no suchi simulation

Energy Technology Data Exchange (ETDEWEB)

Miyazawa, T; Kuwabara, S; Fujii, T [Doshisha University, Kyoto (Japan); Nonaka, K [Bando Chemical Industries, Ltd., Kobe (Japan)

1997-10-01

A numerical model was developed to analyze the power transmitting mechanisms for CVT (Continuous Variable Transmissions) using a dry hybrid belt. The model consists of linear springs representing the rigidities of blocks, rubber and cord, and interface elements which identify slippage between pulleys and blocks. By using the present model, forces acting on the belt were calculated not only at steady but also transitional states. Calculated results well coincide with experimental ones. It is revealed that there is a great change of the pulley thrust when the speed ratio is shifting. Little radial slippage occurs when the pulley groove is reduced. 1 ref., 9 figs.

Effect of mixture formation process of premixed lean diesel combustion. Study of the effect of mixture homogeneity on premixed lean diesel combustion in aid of numerical simulation; Yokongo diesel nensho ni okeru kongoki keisei katei no eikyo. Kongoki no kin`itsusei no eikyo to suchi simulation ni yoru kosatsu

Energy Technology Data Exchange (ETDEWEB)

Shimazaki, N; Miyamoto, T; Akagawa, H; Tsujimura, K

1997-10-01

NOx emission was extremely decreased by PREDIC (PREmixed lean DIesel Combustion) in which fuel was injected at very early stage of compression stroke and the combustion started at near the TDC by self ignition. We have considered that NOx reduction is caused the decrease of a region of stoichiometric mixture ratio by means of extremely early injection. Therefore the homogeneity is very important to decrease of NOx. In this study to investigate the effect of mixture homogeneity in the PREDIC, gaseous fuels (DME, CH4) were charged into the intake, by the combination of direct fuel injection, the mixture heterogeneity was positively changed. In addition the mixture formation process is shown in aid of numerical simulation, it is observed that the homogeneous has the advantage of low NOx emission in PREDIC region. 9 refs., 10 figs., 1 tab.

Fiscal 1997 survey report. Investigational study on the cascade utilization of thermal energy (cold heat and hot heat) (feasibility study by the off-line system); 1997 nendo chosa hokokusho. Netsu energy (reinetsu to onnetsu) no cascade riyo ni kansuru chosa kenkyu (off-line hoshiki ni yoru feasibility study)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper studied a system to effectively use unused and low-grade thermal energy (cold heat and hot heat) in the Tokyo-Yokohama seaside area. For transportation of thermal energy, the batch transportation, that is, off-line system was discussed which uses insulated tank loaded barges and railroad freight trains. Thermal energy supply sources are 1) 0.3 million kW class thermal power plant, and 2) LNG storage base of 3 million ton/year class. Thermal energy users are Tokyo (Haneda) Airport D.H.C. (District Heating/Cooling Co.), MM 21 D.H.C. and Shin-Kawasaki D.H.C. The cold heat energy supplied to these three is about 1.5 million Mcal/daytimes300 days/year, and the hot heat energy supplied is about 1.33 million Mcal/daytimes150 days/year. Cold heat is obtained from seawater after the LNG vaporization, and hot heat from heat extracted from thermal turbine. Subcooled ice was selected for cold heat medium, and PCM-120A for hot heat medium. For batch transportation, an STL heat storage system is used which transports plastic capsules sealed with heat medium. Oil saving of 62,000 tons/year and CO2 reduction of about 53,000 tons/year can be expected. 85 figs., 98 tabs.

1998 report on results of R and D project for industrial science and technology (R and D for technologies of producing innovative high performance material) (development of technologies for structural control material). R and D for high stimuli-responsive material; 1998 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) kodo shigeki oto zairyo no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

A report was made on the results of 1998 R and D concerning high stimuli-responsive materials. This R and D was intended to develop technologies for producing, by copying organism, innovative new stocks and new materials which repeatedly provide functions such as separating, transmitting and moving in response to stimuli. In the R and D of polymeric high stimuli-responsive materials, studies were conducted on multi-stimuli-responsive separation materials, molecular recognition controlled separation materials, and cell adhesion/separation materials with molecular recognition function. In the R and D of composite high stimuli-responsive materials, release controlled function materials and materials for actuator were studied. The investigation and research of common basic technologies were carried out on such subjects as synthesis and functional development of multi-signal responded polymer gels, development of temperature-responsive chromatography, synthesis and characterization of novel stimuli-sensitive materials, studies on structural characterization of intelligent gels, novel thermosensitive polymers, polyelectrolytic model networks, etc. (NEDO)

Report on 1977 result of Sunshine Project. Test research for detailed design of coal gasification plant (pressure fluidized gasification method for mixed material of coal/heavy oil); 1977 nendo sekitan gas ka plant no shosai sekkei no tame no shiken kenkyu seika hokokusho. Sekitan jushitsuyu kongo genryo no kaatsu ryudo gas ka hoshiki

Energy Technology Data Exchange (ETDEWEB)

NONE

1978-03-31

Since fiscal 1974, development has been implemented for the coal/heavy oil hybrid gasification process which converts coal and heavy oil simultaneously to clean fuel gas. With the purpose of obtaining basic data to be reflected on the detailed design of 7,000 Nm{sup 3}/d pilot plant of the subject process started in fiscal 1977, implemented this year were (1) test on high pressure valves and (2) research on operation studies. In (1), a life test device for high pressure operation valves will be designed and manufactured so that basic materials may be obtained for the development of durable operation valves to be used in a high temperature and high pressure coal/heavy oil slurry feeding device. Operation studies of a low pressure slurry feeding device will be continued, accumulating data required for the design of the coal/heavy oil slurry feeding device. In (2), studies will be started on the operation of a 300{phi}(diameter) internal heat type low pressure gasification device, collecting know-how for the model and design of the gasification furnace of the pilot plant. Gasification experiments will be continued using the high pressure gasification device, so that gasification characteristics under a high pressure will be grasped to examine the optimization of gasification conditions. In addition, a fluidized bed quencher test equipment will be designed and manufactured. (NEDO)

Fiscal 1999 research result report on energy and environment technology demonstration research support project (International joint demonstration research project). Improvement of long-distant power transmission efficiency and reliability, and its environmental impact assessment; 1999 nendo chokyori soden hoshiki ni kansuru soden koritsu to soden shinraido no kojo oyobi kankyo eno eikyo hyoka seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Japan-Russia international joint research was made on overhead ultrahigh-voltage DC power transmission lines for transmission loss reduction and reliability improvement, and an optimum international power supply cable system, considering energy saving and environment conservation. Using the European-Russian DC power transmission line of {+-}500kV and 4GW as a model, comparison was made between a model using Russian round strands and glass insulators and a model using Japanese low-loss wires and insulators. As for improvement of the reliability in cold districts, Russian design techniques for tower structure and ice loading were reasonable to counteract galloping oscillation and ice load. In evaluation and selection of optimum underground and marine cables, study was made on cable specifications using the Turkey-Russia power transmission route as a model. The environmental assessment result of these cables showed that XLPE cable under development is optimum. (NEDO)

Fiscal 2000 achievement report on the venture business assisting type regional consortium - Core industry creation type. Research and development of high-accuracy fabrication technology of aspheric optical component creation technology using parallel grinding method; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Parallel kensaku hoshiki ni yoru koseido hikyumen kogaku soshi sosei gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development was carried out for the establishment and commercialization of the technical seeds of a newly proposed 'parallel grinding type aspheric surface grinding method,' based on the results of studies of ultra-accuracy grinding and aspheric surface machining technologies conducted at Tohoku University. The new method is characterized in that a work point on the work piece faces the grinding point on the grindstone cross section on the one-to-one basis because the grinding point travels on the grindstone cross section. Accordingly, the method is quite suitable for corrective grinding for eliminating only the error in case a geometrical error occurs on the wrought surface. For this purpose, measurement of the machine surface on board the machine is indispensable. Hence: a study of corrective grinding methods under an on-board measuring system. As the result, the initially intended geometrical accuracy level was attained in the machining of axis-symmetric aspheric glass lenses and aspheric metal molds, and coarseness on the finished surface in the grinding of glass lenses was reduced to 0.3{mu}m using a diamond grindstone. In conclusion, machining accuracy and finished surface coarseness were remarkably improved, and this enables machining without the need of polishing and demonstrates that there are possibilities of commercialization. (NEDO)

Reports on 1977 result of Sunshine Project. Research for detailed design of coal gasification plant (studies on operating conditions 'pressurized hydro-fluidized gasification method', dissolution of research equipment); 1977 nendo sekitan gas ka plant no shosai sekkei no tame no shiken kenkyu seika hokokusho. Unten joken no kenkyu 'kaatsu suiten ryudo gas ka hoshiki' kenkyu kaitai

Energy Technology Data Exchange (ETDEWEB)

NONE

1978-03-31

The pressurized hydro-fluidized gasification method is such that coal is hydro-gasified under a pressure of 30kg/cm{sup 3} to produce a methane-rich calorie gas. This method is a combination of three independent processes, namely, (1) thermal cracking of coal, (2) hydrogasification of thermally decomposed product, and (3) water gasification for self-contained hydrogen, and is a continuous gasification method in which all processes are operated in a fluidized bed. In fiscal 1976, an operation technique was found in which conditions suitable for each reaction purpose were given to a detached thermal cracking furnace and hydrogasification furnace and in which continuous gasification was still maintained without an adverse effect between the two furnaces. This year, the continuous gasification test will be implemented successively, determining suitable operating conditions for the purpose of increasing methane concentration and improving gasification efficiency, and concurrently extracting device-related problems that impair the continuous operation. With the aim of obtaining a self-contained system for hydrogen, water gasification tests will be conducted, with the optimum conditions determined for the water gasification. An operation test will be carried out for an internal heat type control box, so that the functions under pressurization, durability and operation criteria will be determined. (NEDO)

Achievement report for fiscal 1999. Research on mesh-based estimation of natural energy for Southeast Asia as represented by Myanmar (Assessment of wind power and solar energy using numerical weather model); 1999 nendo Myanmar koku wo rei ni shita Tonan Asia ni okeru shizen energy no mesh suitei ni kansuru kenkyu seika hokokusho. Suchi kisho model ni yoru furyoku taiyo energy hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

As the first step for the introduction of wind power systems and photovoltaic power systems into developing countries in Southeast Asia etc. and for their diffusion in them for the exploitation of natural energy, a numerical weather model useable in Southeast Asia is developed to make up for the insufficiency of weather data in the region. A technique is developed, to explain which the case of Myanmar is cited, for estimating with accuracy such natural conditions as wind direction, wind velocity, and solar radiation in the past one-year period for the assessment of power to be generated using wind turbines and solar panels. The results of the observation of wind conditions indicate that wind directions are mainly northerly or westerly and that wind speeds are as week as 1-3m/s on the average. As for total solar radiation per diem in December through March, it is found that there is 17-23MJ/m{sup 2}/day, which is twice the level to be measured in Tokyo. A comparison is made between the weather observation results and a model calculation, and it is found that the latter sufficiently reproduces the actual weather conditions. Based on the values of wind conditions and solar radiation estimated in Myanmar, the amount of power to be obtained from an assumed arrangement of wind power systems and solar panels is assessed. (NEDO)

Achievement report of projects in fiscal 2000 for measures on technologies to fix and utilize effectively carbon dioxide. Development of program system technologies to fix and utilize effectively carbon dioxide - researches on key technologies (Developing technology to fix carbon dioxide electrochemically); 2000 nendo program hoshiki nisanka tanso koteika yuko riyo gijutsu kaihatsu (kiban gijutsu kenkyu) seika hokokusho (kokaiyo). Nisanka tanso no denki kagakuteki koteika gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With an objective to prevent global warming, research and development has been made on a carbon dioxide fixation technology using electrochemical means. This paper summarizes the achievements in fiscal 2000. In the research of a technology to return carbon dioxide to hydrocarbon such as methane electrochemically utilizing the high concentration carbon dioxide-methanol system, basic studies were performed on electrolytic reduction of CO2 using a methanol solvent system, and experimental studies were executed on high-speed reduction of carbon dioxide using gas diffusion electrodes. In the basic property experiment on diamond electrodes, high carbon dioxide reduction activity was obtained by having copper carried in the diamond electrode. In the CO2 electrolytic reduction experiment on three-phase interface using a copper net electrode, CO, ethylene, and methane were produced, while the electrode has retained the activity for an extended period of time, and the CO2 conversion rate reached about 66%. In structuring an electrochemical carbon dioxide fixation system, specifications for the CO2 electrolytic reduction equipment were determined, design, manufacturing, and electrode materials were selected, supporting electrolytes were discussed, and the entire system flow and liquid resistance were discussed. (NEDO)

Report on the achievements in research and development of a coal liquefaction technology in the Sunshine Project in fiscal 1981. Development of a high-calorie gas manufacturing technology (research on a pressurized and fluidized gasification system for coal and heavy oil mixed materials); Sekitan gas ka gijutsu no kenkyu kaihatsu seika hokokusho. Kokarori gas seizo gijutsu no kaihatsu (sekitan oyobi jushitsuyu kongo genryo no kaatsu ryudo gas ka hoshiki no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

This paper describes the achievements in developing a high-calorie gas manufacturing technology for coal gasification in the Sunshine Project in fiscal 1981. Pulverized coal and heavy oil are heated and stirred to make it a slurry, which is forced into a fluidized bed gasification furnace together with spraying steam, and pyrolyzed by using a unique slurry feeding system (a hydrohoist). Carbon-like material as a by-product (char) is partially oxidized (burned) by steam and oxygen at the lower part of the gasification furnace. The material is gasified in the furnace, where the generated heat is sent to the pyrolysis zone in the upper part by the gas and fluidized bed media particles (char), and utilized as a heat source for the slurry pyrolysis. The produced gas is cooled by an indirect heat exchanger of the fluidized bed system and a scrubber to separate tar, dust and unreacted steam. Part of the sensible heat is recovered as steam. Thus, high-calorie gas of 6,000 kcal/Nm{sup 3} can be obtained, which is rich in methane, CO and hydrogen. Fiscal 1981 has performed a continuous test by using an internal heat type low-pressure gasification equipment to evaluate its compatibility to the diversification of materials. (NEDO)

Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of structure control materials / R and D of multi-stimuli-responsive materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) kodo shigeki oto zairyo no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper described multi-stimuli-responsive materials out of the technology developments for creating original high-functional materials under the system of R and D of industrial scientific technologies. These are materials which repeatedly reproduce functions such as separation, penetration and movement in response to stimuli by imitating living organisms. In relation to polymer multi-stimuli-responsive materials, various copolymers were synthesized using N-acetyl (meta) acrylamide, of which the synthesis method was established in the previous fiscal year, as a main component, and thermal responsive polymer with upper critical solution temperature which becomes a base of separation functional materials was searched for. By immobilizing it with molecular recognition ligand, measured was thermal dependence of affinity of the immobilized matter to albumin. Also studied were molecular recognition cell adhesion/separation functional materials. Concerning composite multi-stimuli-responsive materials, with the use of silica microcapsule surface-immobilized with silane coupling agent, studied were the optimum conditions for immobilizing thermo-responsive polymer to the surface of the capsule. Using motion functional materials by ion exchange resin, obtained was motion functionality which is satisfactory at the state of practical use. 94 refs., 82 figs., 16 tabs.

FY 2000 report on the results of the development of the program system CO2 fixation/effective utilization technology. Development of the technology to assess global warming gas recovery/emission control by restoring/preserving the tropical mangrove coastal ecosystem; 2000 nendo program hoshiki nisanka tanso koteika yuko riyo gijutsu kaihatsu seika hokokusho. Mangrove nado nettai engan seitaikei no shufuku hozen ni yoru chikyu ondanka gas kaishu hoshutsu yokusei hyoka gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of developing the technology to assess the CO2 storage amount using the tropical mangrove coastal ecosystem, survey was conducted in the mangrove tree area in Ishigaki island, Japan and in Trat province, Thailand, and a draft of the assessment method was worked out. As to the assessment of the CO2 existence amount by analysis of satellite pictures, the regression equation between the mangrove existence amount and Landsat satellite data was determined to study a method for assessment of the CO2 storage amount in the whole area for survey. Further, using the relational equation between NDVI and LAI, vegetation indices reflecting vegetation conditions, methods to estimate the CO2 absorption amount by photosynthesis of mangrove tree community, the CO2 emission amount by respiration and the net production amount. Concerning the technology to assess the terrestrial area photosynthesis CO2 absorption amount, methods were studied for direct measurement of the amount of photosynthesis/respiration of the leaf area of mangrove tree community and the respiration amount by area such as trunk, branch and root and for assessment of CO2 absorption amount. Besides, studies were made on a variety of items such as the CO2 absorption/emission amount by underwater photosynthesis/respiration and decomposition of organic substances, the seawater exchange amount, and the rate of decomposition of organic substances. (NEDO)