Environmental assessment for the Strategic Petroleum Reserve Big Hill facility storage of commercial crude oil project, Jefferson County, Texas

International Nuclear Information System (INIS)

1999-03-01

The Big Hill SPR facility located in Jefferson County, Texas has been a permitted operating crude oil storage site since 1986 with benign environmental impacts. However, Congress has not authorized crude oil purchases for the SPR since 1990, and six storage caverns at Big Hill are underutilized with 70 million barrels of available storage capacity. On February 17, 1999, the Secretary of Energy offered the 70 million barrels of available storage at Big Hill for commercial use. Interested commercial users would enter into storage contracts with DOE, and DOE would receive crude oil in lieu of dollars as rental fees. The site could potentially began to receive commercial oil in May 1999. This Environmental Assessment identified environmental changes that potentially would affect water usage, power usage, and air emissions. However, as the assessment indicates, changes would not occur to a major degree affecting the environment and no long-term short-term, cumulative or irreversible impacts have been identified

78 FR 29657 - Prevailing Rate Systems; Definition of Vanderburgh County, Indiana, to a Nonappropriated Fund...

Science.gov (United States)

2013-05-21

...-AM82 Prevailing Rate Systems; Definition of Vanderburgh County, Indiana, to a Nonappropriated Fund... County, IN; and Jefferson and Pulaski Counties, MO. The Federal Prevailing Rate Advisory Committee, the... as follows: [[Page 29658

75 FR 28554 - Foreign-Trade Zone 50 Long Beach, California, Application for Subzone, Louisville Bedding Company...

Science.gov (United States)

2010-05-21

..., California, Application for Subzone, Louisville Bedding Company (Household Bedding Products), Ontario... status for the bedding products manufacturing facility of Louisville Bedding Company (LBC) located in... Avenue in Ontario, California. The facility is used to manufacture household bedding products, including...

Digital Data Set of Orchards Where Arsenical Pesticides Were Likely Used in Clarke and Frederick Counties, Virginia, and Berkeley and Jefferson Counties, West Virginia

Science.gov (United States)

Reed, Bradley W.; Larkins, Peter; Robinson, Gilpin R.

2006-01-01

This data set shows orchard locations in Clarke and Frederick Counties, Virginia and Berkeley and Jefferson Counties, West Virginia where arsenical pesticides were likely used. The orchard locations are based on air photos and topographic maps prepared using information from the time period of extensive use of arsenical pesticides between the 1920s and 1960s. An orchard's presence in this data set does not necessarily indicate the use of arsenical pesticides on the site or that elevated arsenic and metal concentrations are present. Arsenical pesticides may have been used on part, or none, of the land and, under current land use, the land may have been remediated and no longer contain elevated arsenic and metal concentrations in soil. The data set was created to be used in an assessment of soil contamination related to past use of arsenical pesticides in orchards in the northern part of the Great Valley region, Virginia and West Virginia. Previous studies have documented that elevated concentrations of arsenic, lead, and sometimes copper occur in the soils of former apple orchards (Veneman et al., 1983; Jones and Hatch, 1937). Arsenical pesticide use was most extensive and widespread in agricultural applications from the 1920s to the late 1950s, and largely ceased agricultural use by the early 1960s in the nation. During this time period, lead arsenate was the most extensively used arsenical pesticide (Peryea, 1998), particularly in apple orchards. Other metal-bearing pesticides, such as copper acetoarsenite (Paris Green), Bordeaux Blue (a mixture of copper sulfate and calcium hydroxide), and organic mercury fumigants were used to a lesser degree in orchards (Peryea, 1998; Shepard, 1939; Veneman et al., 1983). During the time arsenical pesticides were extensively used, federal and state pesticide laws did not require farmers to keep accurate records of the quantity, location, and type of arsenical pesticides used on their property, thus the quantity and distribution

A theoretical model of subsidence caused by petroleum production: Big Hill Field, Jefferson County, Texas

International Nuclear Information System (INIS)

Hill, D.W.; Sharp, J.M. Jr.

1993-01-01

In the Texas Gulf Coastal Plain, there is a history of oil and gas production extending over 2 to 5 decades. Concurrent with this production history, there has been unprecedented population growth accompanied by vastly increased groundwater demands. Land subsidence on both local and regional bases in this geologic province has been measured and predicted in several studies. The vast majority of these studies have addressed the problem from the standpoint of groundwater usage while only a few have considered the effects of oil and gas production. Based upon field-based computational techniques (Helm, 1984), a model has been developed to predict land subsidence caused by oil and gas production. This method is applied to the Big Hill Field in Jefferson County, Texas. Inputs include production data from a series of wells in this field and lithologic data from electric logs of these same wells. Outputs include predicted amounts of subsidence, the time frame of subsidence, and sensitivity analyses of compressibility and hydraulic conductivity estimates. Depending upon estimated compressibility, subsidence, to date, is predicted to be as high as 20 cm. Similarly, depending upon estimated vertical hydraulic conductivity, the time frame may be decades for this subsidence. These same methods can be applied to other oil/gas fields with established production histories as well as new fields when production scenarios are assumed. Where subsidence has been carefully measured above petroleum reservoir, the model may be used inversely to calculate sediment compressibilities

77 FR 28872 - Notice of FERC Staff Attendance at the SPP-ITO Louisville Gas & Electric/Kentucky Utilities...

Science.gov (United States)

2012-05-16

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission Notice of FERC Staff Attendance at the SPP-ITO Louisville Gas & Electric/Kentucky Utilities Stakeholder Meeting The Federal Energy Regulatory... is part of the Commission's ongoing outreach efforts. SPP-ITO Louisville Gas & Electric/Kentucky...

Status of Thomas Jefferson National Accelerator Facility (Jefferson Lab)

International Nuclear Information System (INIS)

H.A. Grunder

1997-01-01

When first beam was delivered on target in July 1994, the Continuous Electron Beam Accelerator Facility (CEBAF), in Newport News, Virginia realized the return on years of planning and work to create a laboratory devoted to exploration of matter that interacts through the strong force, which holds the quarks inside the proton and binds protons and neutrons into the nucleus. Dedicated this year as the Thomas Jefferson National Accelerator Facility (Jefferson Lab), the completion of construction and beginning of its experimental program has culminated a process that began more than a decade ago with the convening of the Bromley Panel to look at research possibilities for such an electron accelerator

Non-Hawaiian lithostratigraphy of Louisville seamounts and the formation of high-latitude oceanic islands and guyots

Science.gov (United States)

Buchs, David M.; Williams, Rebecca; Sano, Shin-ichi; Wright, V. Paul

2018-05-01

Guyots are large seamounts with a flat summit that is generally believed to form due to constructional biogenic and/or erosional processes during the formation of volcanic islands. However, despite their large abundance in the oceans, there are still very few direct constraints on the nature and formation of guyots, in particular those formed at high latitude that lack a thick cap of shallow-marine carbonate rocks. It is largely accepted based on geophysical constraints and surficial observations/sampling that the summit platform of these guyots is shaped by wave abrasion during post-volcanic subsidence of volcanic islands. Here we provide novel constraints on this hypothesis and the summit geology of guyots with a lithostratigraphic analysis of cores from three Louisville seamounts (South Pacific) collected during Expedition 330 of the Integrated Ocean Drilling Program (IODP). Thirteen lithofacies of sedimentary and volcanic deposits are described, which include facies not previously recognized on the top of guyots, and offer a new insight into the formation of high-latitude oceanic islands on a fast-moving plate. Our results reveal that the lithostratigraphy of Louisville seamounts preserves a very consistent record of the formation and drowning of volcanic islands, with from bottom to top: (i) volcaniclastic sequences with abundant lava-fed delta deposits, (ii) submarine to subaerial shield lava flows, (iii) post-volcanic shallow to deeper marine sedimentary rocks lacking thick reef deposits, (iv) post-erosional rejuvenated volcanic rocks, and (v) pelagic sediments. Recognition of erosional boundaries between subaerial lava flows and shallow-marine sedimentary rocks provides novel support for post-volcanic wave planation of guyots. However, the summit geology of Louisville seamounts is dissimilar to that of high-latitude Hawaiian-Emperor guyots that have emplaced in a similar tectonic and environmental setting and that include thicker lava stacks with apparently

New 40Ar/39Ar age progression for the Louisville hot spot trail and implications for inter-hot spot motion

Science.gov (United States)

Koppers, Anthony A. P.; Gowen, Molly D.; Colwell, Lauren E.; Gee, Jeffrey S.; Lonsdale, Peter F.; Mahoney, John J.; Duncan, Robert A.

2011-12-01

In this study we present 42 new 40Ar/39Ar incremental heating age determinations that contribute to an updated age progression for the Louisville seamount trail. Louisville is the South Pacific counterpart to the Hawaiian-Emperor seamount trail, both trails representing intraplate volcanism over the same time interval (˜80 Ma to present) and being examples of primary hot spot lineaments. Our data provide evidence for an age-progressive trend from 71 to 21 Ma. Assuming fixed hot spots, this makes possible a direct comparison to the Hawaiian-Emperor age progression and the most recent absolute plate motion (APM) model (WK08G) of Wessel and Kroenke (2008). We observe that for the Louisville seamount trail the measured ages are systematically older relative to both the WK08G model predictions and Hawaiian seamount ages, with offsets ranging up to 6 Myr. Taking into account the uncertainty about the duration of eruption and magmatic succession at individual Louisville volcanoes, these age offsets should be considered minimum estimates, as our sampling probably tended to recover the youngest lava flows. These large deviations point to either a contribution of inter-hot spot motion between the Louisville and Hawaiian hot spots or to a more easterly location of the Louisville hot spot than the one inferred in the WK08G model. Both scenarios are investigated in this paper, whereby the more eastern hot spot location (52.0°S, 134.5°W versus 52.4°S, 137.2°W) reduces the average age offset, but still results in a relatively large maximum offset of 3.7 Myr. When comparing the new ages to the APM models (S04P, S04G) by Steinberger et al. (2004) that attempt to compensate for the motion of hot spots in the Pacific (Hawaii) or globally (Hawaii, Louisville, Reunion and Walvis), the measured and predicted ages are more in agreement, showing only a maximum offset of 2.3 Myr with respect to the S04G model. At face value these more advanced APM models, which consider both plate and

University of Louisville Research and Energy Independence Program

Energy Technology Data Exchange (ETDEWEB)

Sunkara, Mahendra K. [Univ. of Louisville, KY (United States)

2016-02-16

The development of domestic, environmentally friendly and sustainable sources of energy and liquid fuel is a critical need for the United States (US). Kentucky (KY) is rich in natural energy and agricultural resources that could provide sustainable energy for the state and for the nation. New technology is needed to capture, store, and distribute this sustainable energy in KY. Development of KY’s sustainable energy resources will create economic benefit for the citizens of KY and can serve as a model for other states in the US. Existing technologies for solar energy collection and storage are practical for regions with high and consistent solar intensity, such as the southwest US. Solar energy is plentiful in KY, but is less intense and less regular. As such, novel innovative technology is needed to capture, store, and distribute this energy. KY also has plentiful biomass resources that can be converted to renewable fuels. In addition, the state offers low energy rates, which are conducive for any type of manufacturing industry. A manufacturing R&D center at the University of Louisville (UofL) can help attract high-tech manufacturing industries to the city of Louisville and the state of KY.

Thomas Jefferson's Academical Village

DEFF Research Database (Denmark)

Foote, Jonathan; Frohburg, Jan

2017-01-01

This is an essay written for the Festschrift of Karl-Heinz Schmitz, Professor at Bauhaus-Universität Weimar. It reflects on some aspects of Thomas Jefferson's design for the University of Virginia in relation to Professor's Schmitz' teachings and interests.......This is an essay written for the Festschrift of Karl-Heinz Schmitz, Professor at Bauhaus-Universität Weimar. It reflects on some aspects of Thomas Jefferson's design for the University of Virginia in relation to Professor's Schmitz' teachings and interests....

Geography and history of the Louisville Hotspot Chain in the southwest Pacific

Science.gov (United States)

Lonsdale, Peter

1988-04-01

The Louisville "Ridge" is a 4300-km-long Late Cretaceous and Cenozoic hotspot chain, the South Pacific equivalent of the Hawaiian-Emperor chain. Its northwestern end is being consumed by the Tonga-Kermadec subduction zone, but Seabeam and magnetic mapping shows that the chain still includes more than 60 major volcanoes, of both normal and reversed polarity, distributed along a 75-km-wide band that can be fitted to small circles about three successive poles of Pacific plate/hotspot rotation. This band obliquely crosses fracture zones of the Eltanin system, but there is little interaction and no evidence of any genetic connection between the two structures. Forty of the Louisville volcanoes grew above sea level and are preserved as high-latitude (i.e., coral-free) guyots. They are spaced less than 100 km apart along most of the chain, but there are none within 750 km of the inferred present location of the hotspot, beneath a swell at the southeast end of the chain. The rate of volcano building by the Louisville hotspot declined sharply about 20 m.y. ago, after being remarkably constant at 3-4×103 km3/m.y. for the previous 50 m.y., and none of the Louisville volcanoes built during the past 10-12 m.y. (the time of most profuse Hawaiian volcanism) has reached sea level. However, a seamount from which Pleistocene lavas were dredged rises to within 540 m of the sea surface from the crest of the hotspot swell at 50.5°S, 139.2°W. Guyot heights demonstrate that a hotspot swell several hundred meters high has persisted throughout the known life of the chain, and sometimes had an isostatic depression on its loaded crest. The depths of guyot shelf breaks increase systematically to the northwest (from 530 to 2100 m) proportional to the square root of volcano age, with some scatter and tilting caused by plate boundary tectonism and local isostatic subsidence and uplift.

Louisville region demonstration of travel management coordination center : system pre-deployment preparation.

Science.gov (United States)

2013-03-01

The purpose of the Greater Louisville Region Demonstration of Travel Management Coordination Center (TMCC): System Pre-Deploy-ment Preparation grant was to further phased implementation of the regions TMCC design by focusing on two major component...

Transient calibration of a groundwater-flow model of Chimacum Creek Basin and vicinity, Jefferson County, Washington: a supplement to Scientific Investigations Report 2013-5160

Science.gov (United States)

Jones, Joseph L.; Johnson, Kenneth H.

2013-01-01

A steady-state groundwater-flow model described in Scientific Investigations Report 2013-5160, ”Numerical Simulation of the Groundwater-Flow System in Chimacum Creek Basin and Vicinity, Jefferson County, Washington” was developed to evaluate potential future impacts of growth and of water-management strategies on water resources in the Chimacum Creek Basin. This supplement to that report describes the unsuccessful attempt to perform a calibration to transient conditions on the model. The modeled area is about 64 square miles on the Olympic Peninsula in northeastern Jefferson County, Washington. The geologic setting for the model area is that of unconsolidated deposits of glacial and interglacial origin typical of the Puget Sound Lowlands. The hydrogeologic units representing aquifers are Upper Aquifer (UA, roughly corresponding to recessional outwash) and Lower Aquifer (LA, roughly corresponding to advance outwash). Recharge from precipitation is the dominant source of water to the aquifer system; discharge is primarily to marine waters below sea level and to Chimacum Creek and its tributaries. The model is comprised of a grid of 245 columns and 313 rows; cells are a uniform 200 feet per side. There are six model layers, each representing one hydrogeologic unit: (1) Upper Confining unit (UC); (2) Upper Aquifer unit (UA); (3) Middle Confining unit (MC); (4) Lower Aquifer unit (LA); (5) Lower Confining unit (LC); and (6) Bedrock unit (OE). The transient simulation period (October 1994–September 2009) was divided into 180 monthly stress periods to represent temporal variations in recharge, discharge, and storage. An attempt to calibrate the model to transient conditions was unsuccessful due to instabilities stemming from oscillations in groundwater discharge to and recharge from streamflow in Chimacum Creek. The model as calibrated to transient conditions has mean residuals and standard errors of 0.06 ft ±0.45 feet for groundwater levels and 0.48 ± 0.06 cubic

Pipeline Corridors through wetlands -- Impacts on plant communities: Mill Creek Tributary Crossing, Jefferson County, New York, 1992 Survey

Energy Technology Data Exchange (ETDEWEB)

Van Dyke, G.D. [Trinity Christian Coll., Palos Heights, IL (United States). Dept. of Biology; Shem, L.M.; Zimmerman, R.E. [Argonne National Lab., IL (United States)

1994-12-01

The goal of the Gas Research Institute Wetland Corridors Program is to identify representative impacts of existing pipelines on the wetlands they traverse. To accomplish this goal, 12 existing wetland crossings were surveyed. These sites varied in elapsed time since pipeline construction, wetland type, pipeline installation techniques, and right-of-way (ROW) management practices. This report presents the results of the survey July 1992, at the Mills Creek tributary crossing, Jefferson County, New York. Data were collected from three wetland communities along the 1991 pipeline and compared with predisturbance data obtained in a June 1991 survey. Within one year after pipeline installation, 50% of the soil surface of the ROW in the scrub-shrub community was covered by emergent vegetation. Average wetland values for the ROW in 1992 were lower than in 1991, indicating that the removal of woody plants resulted in a community composed of species with greater fidelity to wetlands. In the emergent marsh community after one year, the average percentage of surface covered by standing water was greater in the ROW than in the adjacent natural areas. The ROW in the forested wetland community also contained standing water, although none was found in the natural forest areas. The entire study site remains a wetland, with the majority of plant species in all sites being either obligate or facultative wetland species. Weighted and unweighted average wetland indices for each community, using all species, indicated wetland vegetation within the newly established ROW.

77 FR 26968 - Final Flood Elevation Determinations

Science.gov (United States)

2012-05-08

... upstream of Port-Hudson Pride Road. Sheet flow between McCarroll Drive and At North Jefferson Place 1 City.... Road. Approximately 0.9 mile +335 upstream of Wagener Trail Road. Dry Branch At the Hollow Creek West +217 Unincorporated Areas of confluence. Aiken County. Approximately 1,200 feet +318 upstream of Dry...

A New Era for Jefferson Lab

International Nuclear Information System (INIS)

McKeown, R. D.; Montgomery, H. E.; Pennington, M. R.

2016-01-01

On a cool Saturday morning in late April a seemingly endless stream of cars turned off Jefferson Avenue in Newport News, Virginia, bringing 12,000 people ages 1 to 91 to the Open House to learn more about “the new era in science” at the Thomas Jefferson National Accelerator Facility. Here, the visitors were dazzled by the complex equipment, the enthusiastic staff, and the advanced technology at the Laboratory.

University of Louisville Holds Fast to Plans for Big-Time Sports

Science.gov (United States)

Sander, Libby

2009-01-01

For five decades, the University of Louisville men's basketball team has played its home games at the state's fairgrounds, in a modest arena originally built for horse shows. And for just as many seasons, the team's toughest competition for scheduling has come from the livestock--and the flea markets and tractor pulls that also vie for the space.…

The Complexity of Thomas Jefferson. A Response to "'The Diffusion of Light': Jefferson's Philosophy of Education"

Science.gov (United States)

Carpenter, James

2014-01-01

This response argues that Jefferson's educational philosophy must be considered in a proper historical context. Holowchak accurately demonstrates both Jefferson's obsession with education and the political philosophy on which his educational beliefs are built. However, the effort to apply modern democratic and meritocratic attributes to…

Jefferson Lab, a status report

International Nuclear Information System (INIS)

Dunham, B.M.

1996-01-01

Thomas Jefferson National Accelerator Facility (Jefferson Lab; formerly known as CEBAF), operates a 4 GeV, 200 microA continuous wave (CW) electron accelerator that re-circulates the beam five times through two superconducting 400 MeV linacs. Electrons can be extracted from any of the five recirculation passes and beam can be simultaneously delivered to the three experimental halls. As the commissioning stage nears completion, the accelerator is becoming a fully operational machine. Experiments in Hall C have been underway since November 1995 with beam powers of over 300 kW at various energies. Hall A has received beam for spectrometer commissioning, while Hall B is expected to receive its first beam in the fall of 1996. Accelerator availability of greater than 70% during physics runs and excellent beam quality have contributed to making Jefferson Lab a world class laboratory for accelerator-based electromagnetic nuclear physics. With the high performance of the superconducting RF cavities, machine upgrades to 6 GeV, and eventually 8 to 10 GeV are now in the planning stages. Operational and commissioning details concerning all aspects of the machine will be discussed

Jefferson Lab, a status report

International Nuclear Information System (INIS)

Dunham, B.M.

1996-01-01

Thomas Jefferson National Accelerator Facility (Jefferson Lab; formerly known as CEBAF), operates a 4 GeV, 200 μA continuous wave (CW) electron accelerator that re-circulates the beam five times through two superconducting 400 MeV linacs. Electrons can be extracted from any of the five recirculation passes and beam can be simultaneously delivered to the three experimental halls. As the commissioning stage nears completion, the accelerator is becoming a fully operational machine. Experiments in Hall C have been underway since November 1995 with beam powers of over 300 kW at various energies. Hall A has received beam for spectrometer commissioning, while Hall B is expected to receive its first beam in the fall of 1996. Accelerator availability of greater than 70% during physics runs and excellent beam quality have contributed to making Jefferson Lab a world class laboratory for accelerator-based electromagnetic nuclear physics. With the high performance of the superconducting RF cavities, machine upgrades to 6 GeV, and eventually 8 to 10 GeV are now in the planning stages. Operational and commissioning details concerning all aspects of the machine will be discussed. (author)

Summary of Available Hydrogeologic Data for the Northeast Portion of the Alluvial Aquifer at Louisville, Kentucky

National Research Council Canada - National Science Library

Unthank, Michael D; Nelson, Jr., Hugh L

2006-01-01

The hydrogeologic characteristics of the unconsolidated glacial outwash sand and gravel deposits that compose the northeast portion of the alluvial aquifer at Louisville, Kentucky, indicate a prolific...

78 FR 46682 - CSX Transportation, Inc.-Joint Use-Louisville & Indiana Railroad Company, Inc.

Science.gov (United States)

2013-08-01

... Transaction is a ``minor transaction'' under 49 CFR 1180.2(c), and that the application, as supplemented on... Canada. As relevant here, CSXT currently operates over the Line pursuant to trackage rights.\\2\\ \\2\\ See CSX Transp.--Trackage Rights Exemption--Louisville & Ind. R.R., FD 33744 (STB served June 21, 2001...

Solar system installation at Louisville, Kentucky (final report)

Energy Technology Data Exchange (ETDEWEB)

1978-08-07

A contract was awarded in June 1976 for the installation of a solar space heating and domestic hot water system at 2400 Watteroon Trail, Louisville, Kentucky. The overall philosophy used was to install both a liquid and a hot air system retrofitted to the existing office and combined warehouse building. The 1080 sq ft office space is heated first and excess heat is dumped into the warehouse. The two systems offered a unique opportunity to measure the performance and compare results of both air and liquid at one site. The two systems are described in detail and information on the data acquisition system is included.

Digital Data for Volcano Hazards in the Mount Jefferson Region, Oregon

Science.gov (United States)

Schilling, S.P.; Doelger, S.; Walder, J.S.; Gardner, C.A.; Conrey, R.M.; Fisher, B.J.

2008-01-01

Mount Jefferson has erupted repeatedly for hundreds of thousands of years, with its last eruptive episode during the last major glaciation which culminated about 15,000 years ago. Geologic evidence shows that Mount Jefferson is capable of large explosive eruptions. The largest such eruption occurred between 35,000 and 100,000 years ago. If Mount Jefferson erupts again, areas close to the eruptive vent will be severely affected, and even areas tens of kilometers (tens of miles) downstream along river valleys or hundreds of kilometers (hundreds of miles) downwind may be at risk. Numerous small volcanoes occupy the area between Mount Jefferson and Mount Hood to the north, and between Mount Jefferson and the Three Sisters region to the south. These small volcanoes tend not to pose the far-reaching hazards associated with Mount Jefferson, but are nonetheless locally important. A concern at Mount Jefferson, but not at the smaller volcanoes, is the possibility that small-to-moderate sized landslides could occur even during periods of no volcanic activity. Such landslides may transform as they move into lahars (watery flows of rock, mud, and debris) that can inundate areas far downstream. The geographic information system (GIS) volcano hazard data layer used to produce the Mount Jefferson volcano hazard map in USGS Open-File Report 99-24 (Walder and others, 1999) is included in this data set. Both proximal and distal hazard zones were delineated by scientists at the Cascades Volcano Observatory and depict various volcano hazard areas around the mountain.

Nuclear power and the Hamilton-Jefferson debate

International Nuclear Information System (INIS)

Hacker, A.

1980-01-01

The basic sources of nuclear opposition derive from the philosophical arguments of Thomas Jefferson against Alexander Hamilton's vision of an industrial society with a strong central authority. Today's young people continue Jefferson's radical plea for the individual freedoms associated with personal ownership and limited government, but they accept the structure of the former while searching for the romanticism of the latter. The nuclear debate reflects this dichotomy and will continue even if the issues of waste disposal and safety are resolved

Geochemical Evolution of the Louisville Seamount Chain

Science.gov (United States)

Vanderkluysen, L.; Mahoney, J. J.; Koppers, A. A.; Lonsdale, P. F.

2007-12-01

The Louisville seamount chain is a 4300 km long chain of submarine volcanoes in the southwestern Pacific that is commonly thought to represent a hotspot track. It spans an ~80 Myr age range, comparable to that of the Hawaiian-Emperor chain (Koppers et al., G-cubed, 5 (6), 2004). The few previously dredged igneous samples are dominantly basaltic and alkalic, and have been inferred to represent post-shield volcanism (Hawkins et al., AGU Monograph, 43, 235, 1987). Their isotope and trace element signatures suggest an unusually homogenous mantle source (Cheng et al., AGU Monograph, 43, 283, 1987). Dredging in 2006, during the AMAT02RR cruise of the R.V. Revelle, was carried out in the hope of recovering both shield and post-shield samples and of exploring the geochemical evolution of the chain. Igneous rocks were recovered from 33 stations on 23 seamounts covering some 47 Myr of the chain's history. Our study, focusing on the major and trace element and Sr, Nd and Pb isotopic characteristics of these samples, shows that all are alkalic basalts, basanites and tephrites containing normative nepheline. Variations in major and trace elements appear to be controlled predominantly by variable extents of melting and fractional crystallization, with little influence from mantle source heterogeneity. Indeed, age-corrected isotopic values define only a narrow range, in agreement with long-term source homogeneity relative to the scale of melting; e.g., ɛNd varies from +4.1 to +5.7, 206Pb/204Pb from 19.048 to 19.281, and 87Sr/86Sr from 0.70362 to 0.70398. These values broadly fall within the fields of the proposed "C" or "FOZO" mantle end-members. However, small variations are present, with less radiogenic Nd and Pb isotope ratios at the older, western end of the chain, defining a trend toward a broadly EM2-like composition. Although some workers have postulated that the Louisville hotspot was the source of the ~120 Myr Ontong Java Plateau, our samples are isotopically distinct

Nuclear power and the Hamilton-Jefferson debate

Energy Technology Data Exchange (ETDEWEB)

Hacker, A.

The basic sources of nuclear opposition derive from the philosophical arguments of Thomas Jefferson against Alexander Hamilton's vision of an industrial society with a strong central authority. Today's young people continue Jefferson's radical plea for the individual freedoms associated with personal ownership and limited government, but they accept the structure of the former while searching for the romanticism of the latter. The nuclear debate reflects this dichotomy and will continue even if the issues of waste disposal and safety are resolved. (DCK)

Polarized Electrons at Jefferson Laboratory

Energy Technology Data Exchange (ETDEWEB)

Sinclair, C.K.

1997-12-31

The CEBAF accelerator at Jefferson laboratory can deliver CW electron beams to three experimental halls simultaneously. A large fraction of the approved scientific program at the lab requires polarized electron beams. Many of these experiments, both polarized and unpolarized, require high average beam current as well. Since all electrons delivered to the experimental halls originate from the same cathode, delivery of polarized beam to a single hall requires using the polarized source to deliver beam to all experiments in simultaneous operation. The polarized source effort at Jefferson Lab is directed at obtaining very long polarized source operational lifetimes at high average current and beam polarization; at developing the capability to deliver all electrons leaving the polarized source to the experimental halls; and at delivering polarized beam to multiple experimental halls simultaneously.initial operational experience with the polarized source will be presented.

The evolution of Jefferson Lab's control system

International Nuclear Information System (INIS)

K. S. White; M. Bickley; W. Watson

1999-01-01

Thomas Jefferson National Accelerator Facility's (Jefferson Lab) accelerator controls were initially implemented as a proprietary in-house system. During machine commissioning, problems were encountered leading to a decision to migrate to the Experimental Physics and Industrial Controls System (EPICS). Since then, the accelerator and all other laboratory controls have been successfully converted. In addition to implementing Jefferson Lab's controls using EPICS, new data visualization tools have been developed and existing programs have been enhanced with new capabilities. In order to provide a more generic interface for high level applications development, a device abstraction layer, called Common DEVice (CDEV), was implemented. These additions have been made available to other laboratories and are in use at many sites, including some that do not use EPICS. Control System development is not limited to computer scientists; operators, engineers and physicists frequently add capabilities using EPICS, CDEV, Tel/tk, and other tools. These contributions have tailored the control system for many different types of customers. For the future, the authors envision more intelligent processing and more capable tools for data storage, retrieval and visualization

Control system reliability at Jefferson Lab

International Nuclear Information System (INIS)

White, K.S.; Areti, H.; Garza, O.

1997-01-01

At Thomas Jefferson National Accelerator Facility (Jefferson Lab), the availability of the control system is crucial to the operation of the accelerator for experimental programs. Jefferson Lab's control system, uses 68040 based microprocessors running VxWorks, Unix workstations, and a variety of VME, CAMAC. GPIB, and serial devices. The software consists of control system toolkit software, commercial packages, and over 200 custom and generic applications, some of which are highly complex. The challenge is to keep this highly diverse and still growing system, with over 162,000 control points, operating reliably, while managing changes and upgrades to both the hardware and software. Downtime attributable to the control system includes the time to troubleshoot and repair problems and the time to restore the machine to operation of the scheduled program. This paper describes the availability of the control system during the last year, the heaviest contributors to downtime and the response to problems. Strategies for improving the robustness of the control system am detailed and include changes in hardware, software, procedures and processes. The improvements range from the routine preventive hardware maintenance, to improving their ability to detect, predict and prevent problems. This paper also describes the software tools used to assist in control system troubleshooting, maintenance and failure recovery processes

FOREWORD: Jefferson Lab: A Long Decade of Physics

Science.gov (United States)

Montgomery, Hugh

2011-04-01

Jefferson Lab Jefferson Lab was created in 1984 and started operating in about 1996. 2011 is an appropriate time to try to take a look at the results that have appeared, what has been learned, and what has been exciting for our scientific community. Rather than attempt to construct a coherent view with a single author or at least a small number, we have, instead, invited small groups of people who have been intimately involved in the work itself to make contributions. These people are accelerator experts, experimentalists and theorists, staff and users. We have, in the main, sought reviews of the actual sub-fields. The primary exception is the first paper, which sets the scene as it was, in one person's view, at the beginning of Jefferson Lab. In reviewing the material as it appeared, I was impressed by the breadth of the material. Major advances are documented from form factors to structure functions, from spectroscopy to physics beyond the standard model of nuclear and particle physics. Recognition of the part played by spin, the helicities of the beams, the polarizations of the targets, and the polarizations of final state particles, is inescapable. Access to the weak interaction amplitudes through measurements of the parity violating asymmetries has led to quantification of the strange content of the nucleon and the neutron radius of lead, and to measurements of the electroweak mixing angle. Lattice QCD calculations flourished and are setting the platform for understanding of the spectroscopy of baryons and mesons. But the star of the game was the accelerator. Its performance enabled the physics and also the use of the technology to generate a powerful free electron laser. These important pieces of Jefferson Lab physics are given their place. As the third Director of Jefferson Lab, and on behalf of the other physicists and others presently associated with the lab, I would like to express my admiration and gratitude for the efforts of the directors, chief

Relying on the National Mobile Disaster Hospital as a business continuity strategy in the aftermath of a tornado: The Louisville experience.

Science.gov (United States)

Kearns, Randy D; Stringer, Lew; Craig, James; Godette-Crawford, Regina; Black, Paul S; Andra, David L; Winslow, James

2017-01-01

On 28th April, 2014, a tornado left much of Louisville, MS and the local hospital, Winston Medical Center, in ruin. In the USA, temporary hospital solutions have been used to augment the mainstream healthcare system since the American Civil War. As memories fade, however, the necessary readiness for a temporary hospital also fades, at times leaving a patchwork of resources either underfunded or abandoned. With the creation of the Hospital Preparedness Program, several temporary hospital solutions were created in various states across the USA. In the present case, Mississippi and North Carolina resources were used in Louisville in the aftermath of a direct impact that destroyed the hospital and nursing home. In the hours that followed, after lives were saved and patients safely relocated, a frank assessment confirmed the structural loss of the hospital. Local emergency responders, hospital staff, state and federal representatives all rallied with the aim of saving the community's only hospital. The steps taken in Louisville and the deliberate restoration of these essential services offer a learning opportunity for all involved in healthcare disaster preparedness, response and recovery.

Nondestructive testing of a weld repair on the I-65 Bridge over the Ohio River at Louisville.

Science.gov (United States)

2009-06-01

Nondestructive evaluation methods were applied to verify the structural integrity of a fracture critical structural member on the I-65 John F. Kennedy Memorial Bridge over the Ohio River at Louisville. Several nondestructive evaluation methods includ...

Final Technical Report for earmark project "Atmospheric Science Program at the University of Louisville"

Energy Technology Data Exchange (ETDEWEB)

Dowling, Timothy Edward [University of Louisville

2014-02-11

We have completed a 3-year project to enhance the atmospheric science program at the University of Louisville, KY (est. 2008). The goals were to complete an undergraduate atmospheric science laboratory (Year 1) and to hire and support an assistant professor (Years 2 and 3). Both these goals were met on schedule, and slightly under budget.

Polarized electrons at Jefferson laboratory

International Nuclear Information System (INIS)

Sinclair, C.K.

1998-01-01

The CEBAF accelerator at Jefferson laboratory can deliver CW electron beams to three experimental halls simultaneously. A large fraction of the approved scientific program at the lab requires polarized electron beams. Many of these experiments, both polarized and unpolarized, require high average beam current as well. Since all electrons delivered to the experimental halls originate from the same cathode, delivery of polarized beam to a single hall requires using the polarized source to deliver beam to all experiments in simultaneous operation. The polarized source effort at Jefferson Lab is directed at obtaining very long polarized source operational lifetimes at high average current and beam polarization; at developing the capability to deliver all electrons leaving the polarized source to the experimental halls; and at delivering polarized beam to multiple experimental halls simultaneously. Initial operational experience with the polarized source will be presented. copyright 1998 American Institute of Physics

75 FR 13576 - Labor Surplus Area Classification Under Executive Orders 12073 and 10582

Science.gov (United States)

2010-03-22

... County, GA. Jefferson County, GA Jefferson County, GA. Jenkins County, GA Jenkins County, GA. Johnson.... Henry County, IN Henry County, IN. Kokomo city, IN Howard County, IN. LaGrange County, IN LaGrange..., OH Harrison County, OH. Henry County, OH Henry County, OH. Highland County, OH Highland County, OH...

Jefferson Lab: A Long Decade of Physics

International Nuclear Information System (INIS)

Montgomery, Hugh

2011-01-01

Jefferson Lab was created in 1984 and started operating in about 1996. 2011 is an appropriate time to try to take a look at the results that have appeared, what has been learned, and what has been exciting for our scientific community. Rather than attempt to construct a coherent view with a single author or at least a small number, we have, instead, invited small groups of people who have been intimately involved in the work itself to make contributions. These people are accelerator experts, experimentalists and theorists, staff and users. We have, in the main, sought reviews of the actual sub-fields. The primary exception is the first paper, which sets the scene as it was, in one person's view, at the beginning of Jefferson Lab. In reviewing the material as it appeared, I was impressed by the breadth of the material. Major advances are documented from form factors to structure functions, from spectroscopy to physics beyond the standard model of nuclear and particle physics. Recognition of the part played by spin, the helicities of the beams, the polarizations of the targets, and the polarizations of final state particles, is inescapable. Access to the weak interaction amplitudes through measurements of the parity violating asymmetries has led to quantification of the strange content of the nucleon and the neutron radius of lead, and to measurements of the electroweak mixing angle. Lattice QCD calculations flourished and are setting the platform for understanding of the spectroscopy of baryons and mesons. But the star of the game was the accelerator. Its performance enabled the physics and also the use of the technology to generate a powerful free electron laser. These important pieces of Jefferson Lab physics are given their place. As the third Director of Jefferson Lab, and on behalf of the other physicists and others presently associated with the lab, I would like to express my admiration and gratitude for the efforts of the directors, chief scientists

The Qweakp experiment at Jefferson Laboratory

International Nuclear Information System (INIS)

Page, Shelley

2008-01-01

A major new experiment is being prepared at Jefferson Laboratory to measure the proton's weak charge via the parity violating asymmetry in elastic electron-proton scattering at very low momentum transfer. The Standard Model makes a firm prediction of the proton' weak charge, Q w p = 1 - 4 sin2thetaW, based on the running of the weak mixing angle sin2thetaW from the Z 0 pole down to low energies, corresponding to a 10sigma effect in our experiment. Our ultimate goal is to determine the proton' weak charge with 4% combined statistical and systematic errors, which in turn leads to a 0.3% measurement of sin2 thetaW. The experiment is currently under construction; installation in Hall C at Jefferson Lab followed by data taking is planned for 2009.

The Jefferson Lab Trigger Supervisor System

International Nuclear Information System (INIS)

Ed Jastrzembsi; David Abbott; Graham Heyes; R.W. MacLeod; Carl Timmer; Elliott Wolin

2000-01-01

We discuss the design and performance of a Trigger Supervisor System for use in nuclear physics experiments at Jefferson Lab. We also discuss the enhanced features of a new Trigger Supervisor Module now under construction

The Jefferson Lab Trigger Supervisor System

International Nuclear Information System (INIS)

Jastrzembski, E.; Abbott, D.J.; Heyes, W.G.; MacLeod, R.W.; Timmer, C.; Wolin, E.

1999-01-01

The authors discuss the design and performance of a Trigger Supervisor System for use in nuclear physics experiments at Jefferson Lab. They also discuss the enhanced features of a new Trigger Supervisor Module now under construction

40 CFR 81.324 - Minnesota.

Science.gov (United States)

2010-07-01

... and Saint Louis Counties X Jackson County X Kanabec County X Kandiyohi County X Kittson County X..., Credit River Township, Jackson Township, Louisville Township, New Market Township, Spring Lake Township..., Rockford, St. Michael, South Haven, Waverly, Dayton (Wright Co. part), Buffalo Township, Chatham Township...

Making the Case for Jefferson Lab

International Nuclear Information System (INIS)

Gross, Franz

2011-01-01

This chapter is a personal account of the initial planning and competition for a new laboratory, which eventually became known as the Thomas Jefferson National Accelerator Facility, with the official nickname 'Jefferson Lab'. The period covered starts as far back as 1964, with the introduction of quarks, and extends up to the late 1980s after the initial team was assembled, the superconducting design was in place, and construction was well underway. I describe some of the major experiments that were proposed to justify the laboratory, reflect on the present status of those initially proposed experiments, and very briefly outline some of the new ideas that emerged after the laboratory was constructed. The science is presented in a simple manner intended for a lay audience, with some of the ideas illustrated by cartoons that were often used in popular lectures given during this period.

Allegheny County Map Index Grid

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — Map Index Sheets from Block and Lot Grid of Property Assessment and based on aerial photography, showing 1983 datum with solid line and NAD 27 with 5 second grid...

An Overview of Dark Matter Experiments at Jefferson Lab

International Nuclear Information System (INIS)

Boyce, James R

2012-01-01

Dark Matter research at Jefferson Lab started in 2006 with the LIght Pseudoscalar and Scalar Search (LIPSS) collaboration to check the validity of results reported by the PVLAS collaboration. In the intervening years interest in dark matter laboratory experiments has grown at Jefferson Lab. Current research underway or in planning stages probe various mass regions covering 14 orders of magnitude: from 10 −6 eV to 100 MeV. This presentation will be an overview of our dark matter searches, three of which focus on the hypothesized A' gauge boson.

Become Jefferson in cyberspace

Directory of Open Access Journals (Sweden)

Ryszard Tadeusiewicz

2010-01-01

Full Text Available Very newly defined, but fast developing area of e-learning practice, is now known and available for everybody. Therefore it not need more explorers. Most of fundamental facts and properties are discovered and practical “colonization” of such area is already done. But the new area of practical activities of many e-learning specialists need now rules and regulations. Therefore we not need new Columbus of Cyberspace, but Jefferson of Cyberspace is necessary just now!

Thomas Jefferson and the Purposes of Education.

Science.gov (United States)

Jewett, Thomas O.

1997-01-01

Thomas Jefferson was the first conspicuous U.S. advocate of free education supported by local taxation and of state aid to higher education. He believed that only an educated citizenry could assume the responsibilities of self-government. (SK)

Lessons Learned from the Jefferson Lab - SNS Cryomodule Production Run

International Nuclear Information System (INIS)

John Hogan; Edward Daly; John Fischer; Joseph Preble

2005-01-01

In light of the recent developments with the International Linear Collider (ILC), and the recommendation to utilize ''Cold'' technology for this future particle accelerator, this paper will present the lessons learned from the recently concluded Spallation Neutron Source (SNS) superconducting radio frequency (SRF) cryomodule production run at the Thomas Jefferson National Accelerator Facility (Jefferson Lab). Over the past twenty years Jefferson Lab has worked with industry to successfully design, manufacture, test and commission more SRF cryomodules than any other entity in the United States. The knowledge gained from the design and fabrication of the SNS prototype, eleven - 0.61 (medium) beta and the twelve - 0.81 (high) beta cryomodules, will prove to be an effective asset to the ILC project. After delivery of the final production cryomodule in March 2005, design and fabrication data will be collected, evaluated and presented to make this information beneficial for future particle accelerator projects. Recommendations with respect to these findings will also be presented as an integral part of this paper

78 FR 78986 - Changes in Flood Hazard Determinations

Science.gov (United States)

2013-12-27

.... They should not be construed to mean that the community must change any existing ordinances that are... Planning and Commissioners, 100 Zoning, 100 Jefferson County Parkway, Jefferson County Golden, CO 80419. Parkway, Golden, CO 80419. Jefferson, (FEMA Docket No.:, Unincorporated areas The Honorable Donald...

Jefferson Lab Data Acquisition Run Control System

International Nuclear Information System (INIS)

Vardan Gyurjyan; Carl Timmer; David Abbott; William Heyes; Edward Jastrzembski; David Lawrence; Elliott Wolin

2004-01-01

A general overview of the Jefferson Lab data acquisition run control system is presented. This run control system is designed to operate the configuration, control, and monitoring of all Jefferson Lab experiments. It controls data-taking activities by coordinating the operation of DAQ sub-systems, online software components and third-party software such as external slow control systems. The main, unique feature which sets this system apart from conventional systems is its incorporation of intelligent agent concepts. Intelligent agents are autonomous programs which interact with each other through certain protocols on a peer-to-peer level. In this case, the protocols and standards used come from the domain-independent Foundation for Intelligent Physical Agents (FIPA), and the implementation used is the Java Agent Development Framework (JADE). A lightweight, XML/RDF-based language was developed to standardize the description of the run control system for configuration purposes

78 FR 20314 - Jefferson Island Storage & Hub, L.L.C.; Notice of Filing

Science.gov (United States)

2013-04-04

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. PR13-44-000] Jefferson Island Storage & Hub, L.L.C.; Notice of Filing Take notice that on March 28, 2013, Jefferson Island Storage & Hub, L.L.C. filed to revise its Statement of Operating Conditions to among others, update...

Low oxygen saturation and severe anemia in compound heterozygous Hb Louisville [β42(CD1)Phe→Leu] and Hb La Desirade [β129(H7)Ala→Val].

Science.gov (United States)

Kamseng, Parin; Trakulsrichai, Satariya; Trachoo, Objoon; Yimniam, Walaiporn; Panthan, Bhakbhoom; Jittorntam, Paisan; Niparuck, Pimjai; Sanguanwit, Pitsucha; Wananukul, Winai; Jindadamrongwech, Sumalee

2017-03-01

To investigate the cause(s) of a Thai male proband presenting low oxygen saturation by pulse oximetry (SpO 2 ) and severe anemia. As Hb variant was suspected, Hb typing was determined by high-performance liquid chromatography and capillary electrophoresis, and subsequently Hb variant was identified by DNA sequencing. Complete blood counts were performed using automated blood cell counter and oxygen saturation was measured by pulse oximetry. Proband was compound heterozygous for Hb Louisville [β42(CD1)Phe→Leu] and Hb La Desirade [β129(H7)Ala→Val]. Of the proband's two sons, one was compound heterozygous for Hb Louisville and Hb E and the other for Hb La Desirade and Hb E. The former son had similar clinical features and laboratory findings with those of the proband while the latter showed had no abnormal clinical manifestations. This the first report of compound heterozygosity of Hb Louisville and Hb La Desirade in an individual of Southeast Asian ethnicity. Hb variant identification is crucial for genetic counseling and appropriate treatment in regions where hemoglobinopathies are common.

New GPIB Control Software at Jefferson Lab

International Nuclear Information System (INIS)

Matthew Bickley; Pavel Chevtsov

2005-01-01

The control of GPIB devices at Jefferson Lab is based on the GPIB device/driver library. The library is a part of the device/driver development framework. It is activated with the use of the device configuration files that define all hardware components used in the control system to communicate with GPIB devices. As soon as the software is activated, it is ready to handle any device connected to these components and only needs to know the set of commands that the device can understand. The old GPIB control software at Jefferson Lab requires the definition of these commands in the form of a device control software module written in C for each device. Though such modules are relatively simple, they have to be created, successfully compiled, and supported for all control computer platforms. In the new version of GPIB control software all device communication commands are defined in device protocol (ASCII text) files. This makes the support of GPIB devices in the control system much easier

Pipeline corridors through wetlands - impact on plant communities: Mill Creek Tributary Crossing, Jefferson County, New York, 1991 survey. Topical report, June 1991--April 1993

Energy Technology Data Exchange (ETDEWEB)

Van Dyke, G.D. [Argonne National Lab., IL (United States)]|[Trinity Christian College, Palos Heights, IL (United States); Shem, L.M.; Zimmerman, R.E. [Argonne National Lab., IL (United States)

1994-12-01

The goal of the Gas Research Institute Wetland Corridors Program is to document impacts of existing pipelines on the wetlands they traverse. To accomplish this goal, 12 existing wetland crossings were surveyed. These sites varied in elapsed time since pipeline construction, wetland type, pipeline installation techniques, and right-of-way (ROW) management practices. This report presents the results of a survey conducted in June 1991 at the Mill Creek tributary crossing, Jefferson County, New York. One pipeline had been installed through the wetland in 1966, and another was scheduled to be installed later in 1991. Data were collected along the existing pipeline ROW and also along the planned ROW for use as baseline data in future studies. Four separate communities were surveyed. A scrub-shrub wetland and a forested wetland were sampled along the existing ROW where the planned pipeline was to be installed. A mixed vegetation community was sampled along the existing ROW, west of where the planned pipeline would joint the ROW. A marsh community was sampled along the route of the planned pipeline. All plant species found on the ROW of the scrub-shrub community were also present in the adjacent natural areas. The vegetation on the ROW of the forested wetland community also consisted mostly of species found in the adjacent natural areas. In the mixed vegetation community, a small drainage channel present on the ROW, possibly resulting from the pipeline construction, provided habitat for a number of obligate species not found in other areas of this community. Differences noted among different areas of this community were also attributed to slight variations in elevation.

27 CFR 9.78 - Ohio River Valley.

Science.gov (United States)

2010-04-01

... Louisville map) to the town of New Marion in Ripley County, Indiana (Cincinnati map). (7) The boundary proceeds in a straight line northerly to the town of Clarksburg in Decatur County, Indiana (Cincinnati map). (8) The boundary proceeds in a straight line easterly to the town of Ridgeville in Warren County...

Transcription of Gail Jefferson, Boston University Conference on Ethnomethodology and Conversation Analysis, 9 June 1977

DEFF Research Database (Denmark)

Nevile, Maurice Richard

2015-01-01

This is a CLAN transcription of the film recording of a conference talk by Gail Jefferson in Boston in 1977. The film recording was generously made available by George Psathas, Emeritus Professor of Sociology at Boston University. Prof Doug Maynard (University of Wisconsin) arranged for the origi...... paralleling the talk’s content, under the heading ‘The Boston talk (as it never was)’ (p.2) - this would therefore seem to be adapted from Hopper’s transcription. So in my transcription I aim to give a clearer sense of the Boston talk as it actually was.......This is a CLAN transcription of the film recording of a conference talk by Gail Jefferson in Boston in 1977. The film recording was generously made available by George Psathas, Emeritus Professor of Sociology at Boston University. Prof Doug Maynard (University of Wisconsin) arranged...... for the original film recording to be digitised. Jefferson later developed elements of her 1977 talk into the paper ‘On the poetics of ordinary talk’ (Jefferson. G. 1996, in Text and Performance Quarterly, 16,1:1-61). An indication of the significance of the talk is given in that paper’s abstract, where Jefferson...

Origin of the Louisville Ridge and its relationship to the Eltanin Fracture Zone System

Science.gov (United States)

Watts, A. B.; Weissel, J. K.; Duncan, R. A.; Larson, R. L.

1988-04-01

We have combined shipboard and Seasat altimeter derived data in an intergrated geological and geophysical study of the Louisville Ridge; a 3500-km-long seamount chain extending from the Tonga trench to the Eltanin Fracture Zone. A break in the smooth trend of the ridge at latitude 37.5°S has been recognized in both bathymetric and altimetric data. The 40Ar-39Ar dating of rocks dredged either side of the break suggest that it is analogous to the bend in the Hawaiian-Emperor seamount chain. Although the general trend of the ridge can be fit by small circles about Pacific absolute motion poles determined from other seamount chains, the new bathymetric and age data allow us to refine Pacific absolute motion poles. The continuity in smooth trend of the ridge and the Eltanin Fracture Zone suggests some relationship between them. However, a major offset developed on this transform between 60 and 80 Ma, prior to the oldest dated rocks from the ridge. Although magmatism was more or less continuous on the ridge during 28-60 Ma, it probably occurred on crust with little or no offset. Thus magmatism appears to have been little influenced by the developing fracture zone. By 28 Ma, the distance between the magmatic source and the fracture zone had decreased sufficiently for a portion of the ridge to have been emplaced on crust with an offset. After about 12 Ma, however, volcanic activity on the Louisville Ridge apparently waned, despite a possible influence on the magmatism of the fracture zone.

Classical Ethics, Jefferson's Christian Epicureanism, and American Morality.

Science.gov (United States)

Lawler, Peter Augustine

1991-01-01

Outlines Thomas Jefferson's views of classic philosophical writers and various interpretations of their views on morality and epicureanism. Explains why teaching ancient and medieval political philosophy is necessary as an ethical supplement to U.S. political thought. States liberal democracy depends on the tension between reason and revelation.…

PC/104 Embedded IOCs at Jefferson Lab

International Nuclear Information System (INIS)

Yan, Jianxun; Allison, Trent; Witherspoon, Sue; Cuffe, Anthony

2009-01-01

Jefferson Lab has developed embedded IOCs based on PC/104 single board computers (SBC) for low level control systems. The PC/104 IOCs run EPICS on top of the RTEMS operating system. Two types of control system configurations are used in different applications, PC/104 SBC with commercial PC/104 I/O cards and PC/104 SBC with custom designed FPGA-based boards. RTEMS was built with CEXP shell to run on the PC/104 SBC. CEXP shell provides the function of dynamic object loading, which is similar to the widely used VxWorks operating system. Standard software configurations were setup for PC/104 IOC application development to provide a familiar format for new projects as well as ease the conversion of applications from VME based IOCs to PC/104 IOCs. Many new projects at Jefferson Lab are going to employ PC/104 SBCs as IOCs and some applications have already been running them for accelerator operations. The PC/104 - RTEMS IOC provides a free open source Real-Time Operating System (RTOS), low cost/maintenance, easily installed/ configured, flexible, and reliable solution for accelerator control and 12GeV Upgrade projects.

Landscape consequences of natural gas extraction in Cameron, Clarion, Elk, Forest, Jefferson, McKean, Potter, and Warren Counties, Pennsylvania, 2004-2010

Science.gov (United States)

Milheim, L. E.; Slonecker, E. T.; Roig-Silva, C. M.; Winters, S. G.; Ballew, J. R.

2014-01-01

Increased demands for cleaner burning energy, coupled with the relatively recent technological advances in accessing hydrocarbon-rich geologic formations, have led to an intense effort to find and extract unconventional natural gas from various underground sources around the country. One of these sources, the Marcellus Shale, located in the Allegheny Plateau, is currently undergoing extensive drilling and production. The technology used to extract gas in the Marcellus Shale is known as hydraulic fracturing and has garnered much attention because of its use of large amounts of fresh water, its use of proprietary fluids for the hydraulic-fracturing process, its potential to release contaminants into the environment, and its potential effect on water resources. Nonetheless, development of natural gas extraction wells in the Marcellus Shale is only part of the overall natural gas story in this area of Pennsylvania. Conventional natural gas wells, which sometimes use the same technique for extraction, are commonly located in the same general area as the Marcellus Shale and are frequently developed in clusters across the landscape. The combined effects of these two natural gas extraction methods create potentially serious patterns of disturbance on the landscape. This document quantifies the landscape changes and consequences of natural gas extraction for Cameron, Clarion, Elk, Forest, Jefferson, McKean, Potter, and Warren Counties in Pennsylvania between 2004 and 2010. Patterns of landscape disturbance related to natural gas extraction activities were collected and digitized using National Agriculture Imagery Program (NAIP) imagery for 2004, 2005/2006, 2008, and 2010. The disturbance patterns were then used to measure changes in land cover and land use using the National Land Cover Database (NLCD) of 2001. A series of landscape metrics is also used to quantify these changes and is included in this publication. In this region, natural gas and oil development disturbed

BASEMAP, JEFFERSON COUNTY, MS

Data.gov (United States)

Federal Emergency Management Agency, Department of Homeland Security — FEMA Framework Basemap datasets comprise six of the seven FGDC themes of geospatial data that are used by most GIS applications (Note: the seventh framework theme,...

TERRAIN, JEFFERSON COUNTY, USA

Data.gov (United States)

Federal Emergency Management Agency, Department of Homeland Security — Terrain data, as defined in FEMA Guidelines and Specifications, Appendix N: Data Capture Standards, describes the digital topographic data that was used to create...

FLOODPLAIN, JEFFERSON COUNTY, NY

Data.gov (United States)

Federal Emergency Management Agency, Department of Homeland Security — The Floodplain Mapping/Redelineation study deliverables depict and quantify the flood risks for the study area. The primary risk classifications used are the...

NEW EPICS/RTEMS IOC BASED ON ALTERA SOC AT JEFFERSON LAB

Energy Technology Data Exchange (ETDEWEB)

Yan, Jianxun [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Seaton, Chad [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Allison, Trent L. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Bevins, Brian S. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Cuffe, Anthony W. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States)

2018-02-01

A new EPICS/RTEMS IOC based on the Altera System-on-Chip (SoC) FPGA is being designed at Jefferson Lab. The Altera SoC FPGA integrates a dual ARM Cortex-A9 Hard Processor System (HPS) consisting of processor, peripherals and memory interfaces tied seamlessly with the FPGA fabric using a high-bandwidth interconnect backbone. The embedded Altera SoC IOC has features of remote network boot via U-Boot from SD card or QSPI Flash, 1Gig Ethernet, 1GB DDR3 SDRAM on HPS, UART serial ports, and ISA bus interface. RTEMS for the ARM processor BSP were built with CEXP shell, which will dynamically load the EPICS applications at runtime. U-Boot is the primary bootloader to remotely load the kernel image into local memory from a DHCP/TFTP server over Ethernet, and automatically run RTEMS and EPICS. The first design of the SoC IOC will be compatible with Jefferson Lab’s current PC104 IOCs, which have been running in CEBAF 10 years. The next design would be mounting in a chassis and connected to a daughter card via standard HSMC connectors. This standard SoC IOC will become the next generation of low-level IOC for the accelerator controls at Jefferson Lab.

The 8 cm Period Electromagnetic Wiggler Magnet with Coils Made from Sheet Copper

CERN Document Server

Biallas, George H; Hiatt, Tommy; Neil, George R; Snyder, Michael D

2005-01-01

An electromagnetic wiggler, now lasing at the Jefferson Lab FEL, has 29 eight cm periods with K variable from 0.6 to1.1 and gap of 2.6 cm. The wiggler was made inexpensively in 11 weeks by an industrial machine shop. The conduction cooled coil design uses copper sheet material cut to forms using water jet cutting. The conductor is cut to serpentine shapes and the cooling plates are cut to ladder shape. The sheets are assembled in stacks insulated with polymer film, also cut with water jet. The coil design extends the serpentine conductor design of the Duke OK4 to more and smaller conductors. The wiggler features graded fields in the two poles at each end and trim coils on these poles to eliminate field errors caused by saturation. An added critical feature is mirror plates at the ends with integral trim coils to eliminate three dimensional end field effects and align the entrance and exit orbit with the axis of the wiggler. Details of construction, measurement methods and excellent wiggler performance are pre...

Future Scientific Opportunities At Jefferson Lab

International Nuclear Information System (INIS)

Thomas, Anthony

2007-01-01

Nuclear physics requires at least one major facility world-wide which is capable of fully exploiting the properties of the electro-weak force to investigate precisely the structure of strongly interacting systems. At its current maximum energy of 6 GeV Jefferson Lab has provided a wealth of important information on the structure of nucleons and nuclei. However, the plans to double the energy over the next seven years promise to open new frontiers in nuclear and particle physics. We briefly describe the plans for the 12 GeV Upgrade and the associated physics opportunities.

ADVANTAGES OF THE PROGRAM-BASED LOGBOOK SUBMISSION GUI AT JEFFERSON LAB

Energy Technology Data Exchange (ETDEWEB)

T. McGuckin

2006-10-24

DTlite is a Tcl/Tk script that is used as the primary interface for making entries into Jefferson Lab's electronic logbooks. DTlite was originally written and implemented by a user to simplify submission of entries into Jefferson Lab?s electronic logbook, but has subsequently been maintained and developed by the controls software group. The use of a separate, script-based tool for logbook submissions (as opposed to a web-based submission tool bundled with the logbook database/interface) provides many advantages to the users, as well as creating many challenges to the programmers and maintainers of the electronic logbook system. The paper describes the advantages and challenges of this design model and how they have affected the development lifecycle of the electronic logbook system.

40 CFR 81.349 - West Virginia.

Science.gov (United States)

2010-07-01

... Marshall County Mason County McDowell County Mercer County Mineral County Mingo County Monongalia County... Jefferson County Lewis County Lincoln County Logan County Marion County Marshall County Mason County... County Mason County McDowell County Mercer County Mineral County Mingo County Monongalia County Monroe...

A psychometric appraisal of the Jefferson Scale of Empathy using law students

Directory of Open Access Journals (Sweden)

Williams B

2016-07-01

Full Text Available Brett Williams,1 Adiva Sifris,2 Marty Lynch1 1Department of Community Emergency Health and Paramedic Practice, Faculty of Medicine, Nursing and Health Sciences, 2Faculty of Law, Monash University, Frankston, VIC, Australia Background: A growing body of literature indicates that empathic behaviors are positively linked, in several ways, with the professional performance and mental well-being of lawyers and law students. It is therefore important to assess empathy levels among law students using psychometrically sound tools that are suitable for this cohort.Participants and methods: The 20-item Jefferson Scale of Empathy – Health Profession Students Version was adapted for a law context (eg, the word “health care” became “legal”, and the new Jefferson Scale of Empathy – Law Students (JSE-L-S version was completed by 275 students at Monash University, Melbourne, Australia. Data were subjected to principal component analysis.Results: Four factors emerged from the principal component analysis (“understanding the client’s perspective”, “responding to clients’ experiences and emotions”, “responding to clients’ cues and behaviors”, and “standing in clients’ shoes”, which accounted for 46.7% of the total variance. The reliability of the factors varied, but the overall 18-item JSE-L-S yielded a Cronbach’s alpha coefficient of 0.80. Several patterns among the item loadings were similar to those reported in studies using other versions of the Jefferson Scale of Empathy.Conclusion: The JSE-L-S appears to be a reliable measure of empathy among undergraduate law students, which could help provide insights into law student welfare and future performance as legal practitioners. Additional evaluation of the JSE-L-S is required to disambiguate some of the minor findings explored. Adjustments may improve the psychometric properties. Keywords: empathy, law, student, Jefferson, sympathy

Automated path length and M56 measurements at Jefferson Lab

International Nuclear Information System (INIS)

Hardy, D.; Tang, J.; Legg, R.

1997-01-01

Accurate measurement of path length and path length changes versus momentum (M 56 ) are critical for maintaining minimum beam energy spread in the CEBAF (Continuous Electron Beam Accelerator Facility) accelerator at the Thomas Jefferson National Accelerator Facility (Jefferson Lab). The relative path length for each circuit of the beam (1256m) must be equal within 1.5 degrees of 1497 MHz RF phase. A relative path length measurement is made by measuring the relative phases of RF signals from a cavity that is separately excited for each pass of a 4.2 μs pulsed beam. This method distinguishes the path length to less than 0.5 path length error. The development of a VME based automated measurement system for path length and M 56 has contributed to faster machine setup time and has the potential for use as a feedback parameter for automated control

Parent Involvement Handbook.

Science.gov (United States)

Caplan, Arna

This handbook on parent involvement, designed to be used with preschool programs, was developed by the Jefferson County Public Schools in Lakewood, Colorado. Included are: (1) a general statement about parent involvement in an early childhood program, (2) a description of the Jefferson County Early Childhood Program, (3) a description of the…

Recent skyshine calculations at Jefferson Lab

International Nuclear Information System (INIS)

Degtyarenko, P.

1997-01-01

New calculations of the skyshine dose distribution of neutrons and secondary photons have been performed at Jefferson Lab using the Monte Carlo method. The dose dependence on neutron energy, distance to the neutron source, polar angle of a source neutron, and azimuthal angle between the observation point and the momentum direction of a source neutron have been studied. The azimuthally asymmetric term in the skyshine dose distribution is shown to be important in the dose calculations around high-energy accelerator facilities. A parameterization formula and corresponding computer code have been developed which can be used for detailed calculations of the skyshine dose maps

Device Configuration Handler for Accelerator Control Applications at Jefferson Lab

International Nuclear Information System (INIS)

Bickley, Matt; Chevtsov, P.; Larrieu, T.

2003-01-01

The accelerator control system at Jefferson Lab uses hundreds of physical devices with such popular instrument bus interfaces as Industry Pack (IPAC), GPIB, RS-232, etc. To properly handle all these components, control computers (IOCs) must be provided with the correct information about the unique memory addresses of the used interface cards, interrupt numbers (if any), data communication channels and protocols. In these conditions, the registration of a new control device in the control system is not an easy task for software developers. Because the device configuration is distributed, it requires the detailed knowledge about not only the new device but also the configuration of all other devices on the existing system. A configuration handler implemented at Jefferson Lab centralizes the information about all control devices making their registration user-friendly and very easy to use. It consists of a device driver framework and the device registration software developed on the basis of ORACLE database and freely available scripting tools (perl, php)

Precision Electron Beam Polarimetry in Hall C at Jefferson Lab

Science.gov (United States)

Gaskell, David

2013-10-01

The electron beam polarization in experimental Hall C at Jefferson Lab is measured using two devices. The Hall-C/Basel Møller polarimeter measures the beam polarization via electron-electron scattering and utilizes a novel target system in which a pure iron foil is driven to magnetic saturation (out of plane) using a superconducting solenoid. A Compton polarimeter measures the polarization via electron-photon scattering, where the photons are provided by a high-power, CW laser coupled to a low gain Fabry-Perot cavity. In this case, both the Compton-scattered electrons and backscattered photons provide measurements of the beam polarization. Results from both polarimeters, acquired during the Q-Weak experiment in Hall C, will be presented. In particular, the results of a test in which the Møller and Compton polarimeters made interleaving measurements at identical beam currents will be shown. In addition, plans for operation of both devices after completion of the Jefferson Lab 12 GeV Upgrade will also be discussed.

78 FR 36545 - Notice of Ability To Pay-Cash-out Settlement Agreement for the Jefferson City Residential Yards...

Science.gov (United States)

2013-06-18

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9824-4] Notice of Ability To Pay--Cash-out Settlement... payment of certain response costs incurred at the Jefferson City Residential Yards Site in Jefferson City... portion of the past costs expended at the Site. Payment shall be made in 35 installments of $2,500 per...

Recirculating Beam Breakup Study for the 12 GeV Upgrade at Jefferson Lab

International Nuclear Information System (INIS)

Shin, Ilkyoung; Satogata, Todd; Ahmed, Shahid; Bogacz, Slawomir; Stirbet, Mircea; Wang, Haipeng; Wang, Yan; Yunn, Byung; Bodenstein, Ryan

2012-01-01

Two new high gradient C100 cryomodules with a total of 16 new cavities were installed at the end of the CEBAF south linac during the 2011 summer shutdown as part of the 12-GeV upgrade project at Jefferson Lab. We surveyed the higher order modes (HOMs) of these cavities in the Jefferson Lab cryomodule test facility and CEBAF tunnel. We then studied recirculating beam breakup (BBU) in November 2011 to evaluate CEBAF low energy performance, measure transport optics, and evaluate BBU thresholds due to these HOMs. This paper discusses the experiment setup, cavity measurements, machine setup, optics measurements, and lower bounds on BBU thresholds by new cryomodules.

Recirculating Beam Breakup Study for the 12 GeV Upgrade at Jefferson Lab

Energy Technology Data Exchange (ETDEWEB)

Ilkyoung Shin, Todd Satogata, Shahid Ahmed, Slawomir Bogacz, Mircea Stirbet, Haipeng Wang, Yan Wang, Byung Yunn, Ryan Bodenstein

2012-07-01

Two new high gradient C100 cryomodules with a total of 16 new cavities were installed at the end of the CEBAF south linac during the 2011 summer shutdown as part of the 12-GeV upgrade project at Jefferson Lab. We surveyed the higher order modes (HOMs) of these cavities in the Jefferson Lab cryomodule test facility and CEBAF tunnel. We then studied recirculating beam breakup (BBU) in November 2011 to evaluate CEBAF low energy performance, measure transport optics, and evaluate BBU thresholds due to these HOMs. This paper discusses the experiment setup, cavity measurements, machine setup, optics measurements, and lower bounds on BBU thresholds by new cryomodules.

Building Green: Construction for the 21st Century

Science.gov (United States)

Phillipson, Todd

2012-01-01

At Jefferson County Vocational School (JCVS) in Bloomingdale, Ohio, students get a lesson on building green with the construction of a home in the school's subdivision. The home is being built using Energy Star guidelines so that it may be identified as an Energy Star home. The goal for the Jefferson County Vocational Schools Board of Education…

Polarized Source Performance and Developments at Jefferson Lab

International Nuclear Information System (INIS)

Matt Poelker; P. Adderley; J. Clark; A. Day; Joseph Grames; J. Hansknecht; P. Hartmann; R. Kazimi; P. Rutt; Charles Sinclair; M. Steigerwald

2000-01-01

The polarized photoinjector at Jefferson Lab continues to provide high average current, high polarization, high quality beam to nuclear physics Users in as many as three endstations simultaneously. Long lifetime operation has been obtained from two identical polarized guns. A new high power mode locked Ti-sapphire laser has been constructed to enhance the effective operating lifetime of the photoinjector. Efforts to enhance beam polarization and reduced helicity correlated beam systematic effects are underway

Empirically Determined Response Matrices for On-Line Orbit and Energy Correction at Jefferson Lab

International Nuclear Information System (INIS)

Leigh Harwood; Alicia Hofler; Michele Joyce; Valeri Lebedev; David Bryan

2001-01-01

Jefferson Lab uses feedback loops (less than 1 hertz update rate) to correct drifts in CEBAF's electron beam orbit and energy. Previous incarnations of these loops used response matrices that were computed by a numerical model of the machine. Jefferson Lab is transitioning this feedback system to use empirically determined response matrices whereby the software introduces small orbit or energy deviations using the loop's actuators and measures the system response with the loop's sensors. This method is in routine use for orbit correction. This paper will describe the orbit correction system and future plans to extend this method to energy correction

The 12 GeV Upgrade at Jefferson Lab

International Nuclear Information System (INIS)

Rolf Ent

2002-01-01

There has been a remarkable fruitful evolution of our picture of the behavior of strongly interacting matter during the almost two decades that have passed since the parameters of the Continuous Electron Beam Accelerator Facility (CEBAF) at Jefferson Lab were defined. These advances have revealed important new experimental questions best addressed by a CEBAF-class machine at higher energy. Fortunately, favorable technical developments coupled with foresight in the design of the facility make it feasible to triple (double) CEBAF's design (achieved) beam energy from 4 (6) GeV to 12 GeV, in a cost-effective manner: the Upgrade can be realized for about 15% of the cost of the initial facility. This Upgrade would enable the worldwide community to greatly expand its physics horizons. In addition to in general improving the figure of merit and momentum transfer range of the present Jefferson Lab physics program, raising the energy of the accelerator to 12 GeV opens up two main new areas of physics: (1) It allows direct exploration of the quark-gluon structure of hadrons and nuclei in the ''valence quark region''. It is known that inclusive electron scattering at the high momentum and energy transfers available at 12 GeV is governed by elementary interactions with quarks and, indirectly, gluons. The original CEBAF energy is not adequate to study this critical region, while with continuous 12 GeV beams one can cleanly access the entire ''valence quark region'' and exploit the newly discovered Generalized Parton Distributions. In addition, a 12-GeV Jefferson Lab can essentially complete the studies of the transition from hadronic to quark-gluon degrees of freedom. (2) It allows crossing the threshold above which the origins of quark confinement can be investigated. Specifically, 12 GeV will enable the production of certain ''exotic'' mesons. Whereas in the QCD region of asymptotic freedom ample evidence for the role of gluons exist through the observation of gluon jets

75 FR 29189 - Emerald Ash Borer; Addition of Quarantined Areas in Kentucky, Michigan, Minnesota, New York...

Science.gov (United States)

2010-05-25

..., Indiana, Minnesota, Michigan, Ohio, Pennsylvania, West Virginia, and Wisconsin have already been..., Henry, Jefferson, Jessamine, Kenton, Oldham, Owen, Pendleton, Scott, Shelby, Trimble, and Woodford.... Shelby County. The entire county. Trimble County. The entire county. Woodford County. The entire county...

Comparison of NOAA lidar data at 1.5 and 3 meter resolutions, for adequate watershed delineation in Tift County, Georgia, USA

Science.gov (United States)

The USDA Southeast Watershed Research Laboratory is located in Tifton, Ga, and performs ongoing watershed research for the Tift County area, as well as surrounding counties. Current watershed delineations are based on 1972-1977, 7.5-minute USGS Quadrangle sheets, and require updating. Light Detectio...

40 CFR 81.311 - Georgia.

Science.gov (United States)

2010-07-01

... County X Hart County X Heard County X Henry County X Houston County X Irwin County X Jackson County X Jasper County X Jeff Davis County X Jefferson County X Jenkins County X Johnson County X Jones County X... County X Hart County X Heard County X Henry County X Houston County X Irwin County X Jackson County X...

An overview of recent nucleon spin structure measurements at Jefferson Lab

Energy Technology Data Exchange (ETDEWEB)

Allada, Kalyan [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States)

2016-02-01

Jefferson Lab have made significant contributions to improve our knowledge of the longitudinal spin structure by measuring polarized structure functions, g1 and g2, down to Q2 = 0.02 GeV2. The low Q2 data is especially useful in testing the Chiral Perturbation theory (cPT) calculations. The spin-dependent sum rules and the spin polarizabilities, constructed from the moments of g1 and g2, provide an important tool to study the longitudinal spin structure. We will present an overview of the experimental program to measure these structure functions at Jefferson Lab, and present some recent results on the neutron polarizabilities, proton g1 at low Q2, and proton and neutron d2 measurement. In addition to this, we will discuss the transverse spin structure of the nucleon which can be accessed using chiral-odd transversity distribution (h1), and show some results from measurements done on polarized 3He target in Hall A.

Runtime accelerator configuration tools at Jefferson Laboratory

International Nuclear Information System (INIS)

Tiefenback, M.G.; Doolittle, L.; Benesch, J.F.

1997-01-01

RF and magnet system configuration and monitoring tools are being implemented at Jefferson Lab to improve system reliability and reduce operating costs. They are prototype components of the Momentum Management System being developed. The RF is of special interest because it affects the momentum and momentum spread of the beam, and because of the immediate financial benefit of managing the klystron DC supply power. The authors describe present and planned monitoring of accelerating system parameters, use of these data, RF system performance calculations, and procedures for magnet configuration for handling beam of any of five beam energies to any of three targets

SURVEY, JEFFERSON DAVIS COUNTY, MS

Data.gov (United States)

Federal Emergency Management Agency, Department of Homeland Security — Survey data includes spatial datasets and data tables necessary to digitally represent data collected in the survey phase of the study. (Source: FEMA Guidelines and...

BASEMAP, JEFFERSON DAVIS COUNTY, MS

Data.gov (United States)

Federal Emergency Management Agency, Department of Homeland Security — FEMA Framework Basemap datasets comprise six of the seven FGDC themes of geospatial data that are used by most GIS applications (Note: the seventh framework theme,...

FLOODPLAIN, JEFFERSON COUNTY, ALABAMA USA

Data.gov (United States)

Federal Emergency Management Agency, Department of Homeland Security — The Floodplain Mapping/Redelineation study deliverables depict and quantify the flood risks for the study area. The primary risk classifications used are the...

TERRAIN, JEFFERSON COUNTY, ALABAMA USA

Data.gov (United States)

Federal Emergency Management Agency, Department of Homeland Security — Terrain data, as defined in FEMA Guidelines and Specifications, Appendix N: Data Capture Standards, describes the digital topographic data that was used to create...

HYDROLOGY, JEFFERSON COUNTY, WI, USA

Data.gov (United States)

Federal Emergency Management Agency, Department of Homeland Security — Hydrology data include spatial datasets and data tables necessary for documenting the hydrologic procedures for estimating flood discharges for a flood insurance...

A Green Fabry-Perot Cavity for Jefferson Lab Hall A Compton Polarimetry

International Nuclear Information System (INIS)

Rakhman, Abdurahim; Souder, Paul; Nanda, Sirish

2009-01-01

A green laser (CW, 532 nm) based Fabry-Perot cavity for high precision Compton Polarimetry is under development in Hall A of the Jefferson Laboratory. In this paper, we present the principle and the preliminary studies for our test cavity.

Transcribing Gail Jefferson: The 1977 Boston talk as it actually was

DEFF Research Database (Denmark)

Nevile, Maurice Richard

2015-01-01

A talk by Gail Jefferson, one of the founders of Conversation Analysis, has been recently made available, and Maurice Nevile undertook to transcribe it for the benefit of the language-in-interaction community. Here he reports on what it meant to him, and what we can all get out of such a powerful...

The Jefferson Lab High Power Light Source

Energy Technology Data Exchange (ETDEWEB)

James R. Boyce

2006-01-01

Jefferson Lab has designed, built and operated two high average power free-electron lasers (FEL) using superconducting RF (SRF) technology and energy recovery techniques. Between 1999-2001 Jefferson Lab operated the IR Demo FEL. This device produced over 2 kW in the mid-infrared, in addition to producing world record average powers in the visible (50 W), ultraviolet (10 W) and terahertz range (50 W) for tunable, short-pulse (< ps) light. This FEL was the first high power demonstration of an accelerator configuration that is being exploited for a number of new accelerator-driven light source facilities that are currently under design or construction. The driver accelerator for the IR Demo FEL uses an Energy Recovered Linac (ERL) configuration that improves the energy efficiency and lowers both the capital and operating cost of such devices by recovering most of the power in the spent electron beam after optical power is extracted from the beam. The IR Demo FEL was de-commissioned in late 2001 for an upgraded FEL for extending the IR power to over 10 kW and the ultraviolet power to over 1 kW. The FEL Upgrade achieved 10 kW of average power in the mid-IR (6 microns) in July of 2004, and its IR operation currently is being extended down to 1 micron. In addition, we have demonstrated the capability of on/off cycling and recovering over a megawatt of electron beam power without diminishing machine performance. A complementary UV FEL will come on-line within the next year. This paper presents a summary of the FEL characteristics, user community accomplishments with the IR Demo, and planned user experiments.

75 FR 71079 - Site Renumbering Notice; Foreign-Trade Zone 29-Louisville, KY

Science.gov (United States)

2010-11-22

... Interstate 65, Shepherdsville, Bullitt County; Site 7 (191 acres)--Henderson County Riverport Authority... Park, 376 Zappos Blvd., Shepherdsville, Bullitt County [formerly part of Site 6]; and, Site 13 (6 acres...

GlueX: The Search for Gluonic Excitations at Jefferson Laboratory

Energy Technology Data Exchange (ETDEWEB)

D.S. Carman

2005-08-21

One of the unanswered and most fundamental questions in physics regards the nature of the confinement mechanism of quarks and gluons in quantum chromodynamics (QCD). Exotic hybrid mesons manifest gluonic degrees of freedom and their detailed spectroscopy will provide the precision data necessary to test assumptions in lattice QCD and the specific phenomenology leading to confinement. Photoproduction is expected to be a particularly effective manner to produce exotic hybrids, however, existing data using photon beams are sparse. At Jefferson Laboratory, plans are underway by the GlueX Collaboration to use the coherent bremsstrahlung technique to produce a linearly polarized photon beam. A solenoid-based hermetic detector will be used to collect data on meson production and decays with statistics that will exceed existing photoproduction data by several orders of magnitude after the first year of running. In order to reach the ideal photon energy of 9 GeV required for these studies, the energy of the Jefferson Laboratory electron accelerator, CEBAF, will be doubled from its current maximum energy of 6 GeV to 12 GeV. The physics motivating the search and the status of the project are reviewed.

Bridge Scour Monitoring Methods at Three Sites in Wisconsin

National Research Council Canada - National Science Library

Walker, John F; Hughes, Peter E

2005-01-01

.... Geological Survey, in cooperation with the Wisconsin Department of Transportation, the Marathon County Highway Department, and the Jefferson County Highway Department, performed routine monitoring...

Proposal for a slow positron facility at Jefferson National Laboratory

Science.gov (United States)

Mills, Allen P.

2018-05-01

One goal of the JPos-17 International Workshop on Physics with Positrons was to ascertain whether it would be a good idea to expand the mission of the Thomas Jefferson National Accelerator Facility (JLab) to include science with low energy (i.e. "slow") spin polarized positrons. It is probably true that experimentation with slow positrons would potentially have wide-ranging benefits comparable to those obtained with neutron and x-ray scattering, but it is certain that the full range of these benefits will never be fully available without an infrastructure comparable to that of existing neutron and x-ray facilities. The role for Jefferson Laboratory would therefore be to provide and maintain (1) a dedicated set of machines for making and manipulating high intensity, high brightness beams of polarized slow positrons; (2) a suite of unique and easily used instruments of wide utility that will make efficient use of the positrons; and (3) a group of on-site positron scientists to provide scientific leadership, instrument development, and user support. In this note some examples will be given of the science that might make a serious investment in a positron facility worthwhile. At the same time, the lessons learned from various proposed and successful positron facilities will be presented for consideration.

Surficial geologic map of Berrien County, Michigan, and the adjacent offshore area of Lake Michigan

Science.gov (United States)

Stone, Byron D.; Kincare, Kevin A.; O'Leary, Dennis W.; Newell, Wayne L.; Taylor, Emily M.; Williams, Van S.; Lundstrom, Scott C.; Abraham, Jared E.; Powers, Michael H.

2017-12-13

The surficial geologic map of Berrien County, southwestern Michigan (sheet 1), shows the distribution of glacial and postglacial deposits at the land surface and in the adjacent offshore area of Lake Michigan. The geologic map differentiates surficial materials of Quaternary age on the basis of their lithologic characteristics, stratigraphic relationships, and age. Drill-hole information correlated in cross sections provides details of typical stratigraphic sequences that compose one or more penetrated geologic map units. A new bedrock geologic map (on sheet 2) includes contours of the altitude of the eroded top of bedrock and shows the distribution of middle Paleozoic shale and carbonate units in the subcrop. A sediment thickness map (also on sheet 2) portrays the extent of as much as 150 meters of surficial materials that overlie the bedrock surface.The major physical features of the county are related principally to deposits of the last Laurentide ice sheet that advanced and then retreated back through the region from about 19,000 to 14,000 radiocarbon years before present. Glacial and postglacial deposits underlie the entire county; shale bedrock crops out only in the adjacent offshore area on the bottom of Lake Michigan. All glacial deposits and glacial meltwater deposits in Berrien County are related to the late Wisconsinan glacial advances of the Lake Michigan ice lobe and its three regional recessional moraines, which cross the county as three north-northeast-trending belts.From east to west (oldest to youngest), the three moraine belts are known as the Kalamazoo, Valparaiso, and Lake Border morainic systems. The till-ridge morainic systems (Lake Border and local Valparaiso morainic systems) consist of multiple, elongate moraine ridges separated by till plains and lake-bottom plains. Tills in ground and end moraines in Berrien County are distinguished as informal units, and are correlated with three proposed regional till units in southwestern Michigan

Basic repository source term and data sheet report: Deaf Smith County

International Nuclear Information System (INIS)

1987-01-01

This report is one of a series describing studies undertaken in support of the US Department of Energy Civilian Radioactive Waste Management (CRWM) Program. This study contains the derivation of values for environmental source terms and resources consumed for a CRWM repository. Estimates include heavy construction equipment; support equipment; shaft-sinking equipment; transportation equipment; and consumption of fuel, water, electricity, and natural gas. Data are presented for construction and operation at an assumed site in Deaf Smith County, Texas. 2 refs., 6 tabs

Studies of the neutron spin structure at Jefferson Lab

International Nuclear Information System (INIS)

Korsch, W.

2003-01-01

The polarized 3 He program of Hall A at Jefferson Lab will be described. Results on the generalized Gerasimov-Drell-Hearn integral for the neutron in a Q 2 range between 0.02 GeV 2 /c 2 2 2 /c 2 will be presented. Preliminary results of the virtual photon asymmetry A 1 n (x,Q 2 ) and the spin structure function g 2 n (x,Q 2 ) at large values of Bjorken x and low Q 2 , respectively, will be discussed. (orig.)

FOCUSED FEASIBILITY STUDY OF PHYTOREMEDIATION ALTERNATIVE FOR THE INDUSTRIAL EXCESS LANDFILL SITE IN STARK COUNTY, OHIO.

Science.gov (United States)

Focused feasibility study of phytoremediation alternative for the Industrial Excess Landfill site in Stark County, Ohio. More information can be found on the NPL Fact Sheet for this site at www.epa.gov/region5/superfund/npl/ohio/OHD000377971.htm

The Jefferson Lab Frozen Spin Target

Energy Technology Data Exchange (ETDEWEB)

Christopher Keith, James Brock, Christopher Carlin, Sara Comer, David Kashy, Josephine McAndrew, David Meekins, Eugene Pasyuk, Joshua Pierce, Mikell Seely

2012-08-01

A frozen spin polarized target, constructed at Jefferson Lab for use inside a large acceptance spectrometer, is described. The target has been utilized for photoproduction measurements with polarized tagged photons of both longitudinal and circular polarization. Protons in TEMPO-doped butanol were dynamically polarized to approximately 90% outside the spectrometer at 5 T and 200-300 mK. Photoproduction data were acquired with the target inside the spectrometer at a frozen-spin temperature of approximately 30 mK with the polarization maintained by a thin, superconducting coil installed inside the target cryostat. A 0.56 T solenoid was used for longitudinal target polarization and a 0.50 T dipole for transverse polarization. Spin relaxation times as high as 4000 hours were observed. We also report polarization results for deuterated propanediol doped with the trityl radical OX063.

77 FR 47084 - Changes in Flood Hazard Determinations

Science.gov (United States)

2012-08-07

... Avenue, Atmore, index.php/alabama/ Atmore, City AL 36502. escambia/. Hall, 201 East Louisville Avenue..., Avenue, Brewton, index.php/alabama/ 2355P). Escambia County AL 36426. escambia/. Board of Commissioners..., Engineering index.php/alabama/ P.O. Box 2128, Services houston/. Dothan, AL 36302. Division, 126 North St...

75 FR 12792 - National Register of Historic Places; Notification of Pending Nominations and Related Actions

Science.gov (United States)

2010-03-17

...., 209 & 301 W. Pierce, & 524 & 600 Huntington, Council Bluffs, 10000160 MASSACHUSETTS Franklin County... following resources: WEST VIRGINIA Jefferson County Beverley, 1 Burns Farm Rd., Charles Town, 87000486 [FR...

The CLAS12 Torus Detector Magnet at Jefferson Laboratory

Energy Technology Data Exchange (ETDEWEB)

Luongo, Cesar [Jefferson Lab; Ballard, Joshua [Jefferson Lab; Biallas, George [Jefferson Lab; Elouadrhiri, Latifa [Jefferson Lab; Fair, Ruben [Jefferson Lab; Ghoshal, Probir [Jefferson Lab; Kashy, Dave [Jefferson Lab; Legg, Robert [Jefferson Lab; Pastor, Orlando [Jefferson Lab; Rajput-Ghoshal, Renuka [Jefferson Lab; Rode, Claus [Jefferson Lab; Wiseman, Mark [Jefferson Lab; Young, Glenn [Jefferson Lab; Elementi, Luciano [Fermilab; Krave, Steven [Fermilab; Makarov, Alexander [Fermilab; Nobrega, Fred [Fermilab; Velev, George [Fermilab

2015-12-17

The CLAS12 Torus is a toroidal superconducting magnet, which is part of the detector for the 12-GeV accelerator upgrade at Jefferson Laboratory (JLab). The coils were wound/fabricated by Fermilab, with JLab responsible for all other parts of the project scope, including design, integration, cryostating the individual coils, installation, cryogenics, I&C, etc. This paper provides an overview of the CLAS12 Torus magnet features and serves as a status report of its installation in the experimental hall. Completion and commissioning of the magnet is expected in 2016.

Water quality of streams in Johnson County, Kansas, 2002-07

Science.gov (United States)

Rasmussen, T.J.

2009-01-01

Water quality of streams in Johnson County, Kansas was evaluated from October 2002 through December 2007 in a cooperative study between the U.S. Geological Survey and the Johnson County Stormwater Management Program. Water quality at 42 stream sites, representing urban and rural basins, was characterized by evaluating benthic macroinvertebrates, water (discrete and continuous data), and/or streambed sediment. Point and nonpoint sources and transport were described for water-quality constituents including suspended sediment, dissolved solids and major ions, nutrients (nitrogen and phosphorus), indicator bacteria, pesticides, and organic wastewater and pharmaceutical compounds. The information obtained from this study is being used by city and county officials to develop effective management plans for protecting and improving stream quality. This fact sheet summarizes important results from three comprehensive reports published as part of the study and available on the World Wide Web at http://ks.water.usgs.gov/Kansas/studies/qw/joco/. ?? 2009 ASCE.

An overview of the user program for the Jefferson Lab free electron laser

International Nuclear Information System (INIS)

Dylla, H.F.

1999-01-01

Jefferson Lab is commissioning a high-average-power IR FEL during 1998. When driven with its superconducting linac operating in a recirculated mode, the IR Demo FEL is capable of producing kilowatt-level average power in the mid-infrared (2-7 mu m) range. With operational experience and hardware changes involving primarily change-out of the optical cavity mirrors, the FEL is capable of covering a wide range of the infrared (1-16 mu m) at power levels exceeding 100 W. This tuning range combined with a unique pulse structure makes the Jefferson Lab FEL a versatile research and development tool for a wide variety of laser applications. A core group of industrial partners has been involved in planning applications using the FEL since 1991. This initial user group was augmented with university partners in 1993 and with participants from several national laboratories in 1996-1997. With the initiation of construction of the FEL and the associated 600 m 2 user facility laboratory in 1996, a number of topical user groups were formed to plan and implement the first series of user experiments. The industrial partners have formed user groups planning applications in polymer surface processing, metal surface processing, microfabrication, and electronic materials. University partners have submitted proposals on basic science topics which complement and planned applied research topics, in addition to proposing experiments in atomic physics, chemical physics and materials science which take advantage of one or more of the unique characteristics of the FEL. A synopsis of the proposed user experiments for the first phase of operation of the Jefferson Lab FEL will be presented

Jefferson Lab's Distributed Data Acquisition

International Nuclear Information System (INIS)

Trent Allison; Thomas Powers

2006-01-01

Jefferson Lab's Continuous Electron Beam Accelerator Facility (CEBAF) occasionally experiences fast intermittent beam instabilities that are difficult to isolate and result in downtime. The Distributed Data Acquisition (Dist DAQ) system is being developed to detect and quickly locate such instabilities. It will consist of multiple Ethernet based data acquisition chassis distributed throughout the seven-eights of a mile CEBAF site. Each chassis will monitor various control system signals that are only available locally and/or monitored by systems with small bandwidths that cannot identify fast transients. The chassis will collect data at rates up to 40 Msps in circular buffers that can be frozen and unrolled after an event trigger. These triggers will be derived from signals such as periodic timers or accelerator faults and be distributed via a custom fiber optic event trigger network. This triggering scheme will allow all the data acquisition chassis to be triggered simultaneously and provide a snapshot of relevant CEBAF control signals. The data will then be automatically analyzed for frequency content and transients to determine if and where instabilities exist

Heterogeneity of exposure and attribution of mesothelioma: Trends and strategies in two American counties

International Nuclear Information System (INIS)

Case, B W; Abraham, J L

2009-01-01

As mesothelioma risk has begun to decline in the United States, two trends are gaining relative importance. 'Legacy' exposures causing this disease are most important in locales having past asbestos industry, shipyards, and/or local distribution of asbestos amphibole-containing material as a result. 'Future' exposures are of particular concern in relation to so-called 'naturally occurring asbestos' (NOA) areas which include unequivocally asbestiform amphibole. In this paper, Jefferson Parish, Louisiana is used as an example of the first trend, and El Dorado County, California as an example of the second. Available tumor registry, epidemiology, historical and mineralogical data, and lung-retained fibre content are used as indicators of disease and exposure. Jefferson Parish, LA was chosen as the prototype of 'legacy' exposures on the basis of historical evidence of asbestos plants with known mesotheliomas in the workforce, known shipyards in the same area, EPA records of distribution of crocidolite-containing scrap to and remediation of over 1400 properties, NIOSH published data on mesothelioma by county, and exposure data including lung-retained fibre analyses in victims, where available. El Dorado, CA was chosen as the prototype of NOA amphibole exposures on the basis of tumor registry data, activity-based EPA sampling data in one area, and lung-retained fibre analyses in area pets, and future risk assessment based on tremolite-specific modelling in Libby, Montana and elsewhere. As expected, the legacy exposure area was high in mesothelioma incidence and mortality. Lung-retained fibre content confirms crocidolite exposures in exposed plant-workers and those exposed to crocidolite-containing scrap, and amosite in shipyard workers. In contrast, to date, cancer registry data in the NOA-amphibole ('future') county does not show a clear increase in incidence or mortality, but grouped county data from the area show a shift in higher incidence rates to the NOA areas and

Heterogeneity of exposure and attribution of mesothelioma: Trends and strategies in two American counties

Science.gov (United States)

Case, B. W.; Abraham, J. L.

2009-02-01

As mesothelioma risk has begun to decline in the United States, two trends are gaining relative importance. "Legacy" exposures causing this disease are most important in locales having past asbestos industry, shipyards, and/or local distribution of asbestos amphibole-containing material as a result. "Future" exposures are of particular concern in relation to so-called "naturally occurring asbestos" (NOA) areas which include unequivocally asbestiform amphibole. In this paper, Jefferson Parish, Louisiana is used as an example of the first trend, and El Dorado County, California as an example of the second. Available tumor registry, epidemiology, historical and mineralogical data, and lung-retained fibre content are used as indicators of disease and exposure. Jefferson Parish, LA was chosen as the prototype of "legacy" exposures on the basis of historical evidence of asbestos plants with known mesotheliomas in the workforce, known shipyards in the same area, EPA records of distribution of crocidolite-containing scrap to and remediation of over 1400 properties, NIOSH published data on mesothelioma by county, and exposure data including lung-retained fibre analyses in victims, where available. El Dorado, CA was chosen as the prototype of NOA amphibole exposures on the basis of tumor registry data, activity-based EPA sampling data in one area, and lung-retained fibre analyses in area pets, and future risk assessment based on tremolite-specific modelling in Libby, Montana and elsewhere. As expected, the legacy exposure area was high in mesothelioma incidence and mortality. Lung-retained fibre content confirms crocidolite exposures in exposed plant-workers and those exposed to crocidolite-containing scrap, and amosite in shipyard workers. In contrast, to date, cancer registry data in the NOA-amphibole ("future") county does not show a clear increase in incidence or mortality, but grouped county data from the area show a shift in higher incidence rates to the NOA areas and

Heterogeneity of exposure and attribution of mesothelioma: Trends and strategies in two American counties

Energy Technology Data Exchange (ETDEWEB)

Case, B W [Department of Pathology and School of Environment, McGill University, Montreal, Quebec (Canada); Abraham, J L, E-mail: bruce.case@mcgill.c [Department of Pathology, SUNY Upstate Medical University, Syracuse, NY 13210 (United States)

2009-02-01

As mesothelioma risk has begun to decline in the United States, two trends are gaining relative importance. 'Legacy' exposures causing this disease are most important in locales having past asbestos industry, shipyards, and/or local distribution of asbestos amphibole-containing material as a result. 'Future' exposures are of particular concern in relation to so-called 'naturally occurring asbestos' (NOA) areas which include unequivocally asbestiform amphibole. In this paper, Jefferson Parish, Louisiana is used as an example of the first trend, and El Dorado County, California as an example of the second. Available tumor registry, epidemiology, historical and mineralogical data, and lung-retained fibre content are used as indicators of disease and exposure. Jefferson Parish, LA was chosen as the prototype of 'legacy' exposures on the basis of historical evidence of asbestos plants with known mesotheliomas in the workforce, known shipyards in the same area, EPA records of distribution of crocidolite-containing scrap to and remediation of over 1400 properties, NIOSH published data on mesothelioma by county, and exposure data including lung-retained fibre analyses in victims, where available. El Dorado, CA was chosen as the prototype of NOA amphibole exposures on the basis of tumor registry data, activity-based EPA sampling data in one area, and lung-retained fibre analyses in area pets, and future risk assessment based on tremolite-specific modelling in Libby, Montana and elsewhere. As expected, the legacy exposure area was high in mesothelioma incidence and mortality. Lung-retained fibre content confirms crocidolite exposures in exposed plant-workers and those exposed to crocidolite-containing scrap, and amosite in shipyard workers. In contrast, to date, cancer registry data in the NOA-amphibole ('future') county does not show a clear increase in incidence or mortality, but grouped county data from the area show a

78 FR 33051 - Non-Rock Alternatives to Shoreline Protection Demonstration Project (LA-16) Iberia, Jefferson...

Science.gov (United States)

2013-06-03

... DEPARTMENT OF AGRICULTURE Natural Resources Conservation Service Non-Rock Alternatives to...-Rock Alternatives to Shoreline Protection Demonstration Project (LA-16), Iberia, Jefferson, and... and environmental limitations preclude the use of rock structures. The shoreline protection systems...

76 FR 18753 - Jefferson Island Storage & Hub, L.L.C.; Notice of Filing

Science.gov (United States)

2011-04-05

... notification when a document is added to a subscribed docket(s). For assistance with any FERC Online service... services provided under section 311 of the Natural Gas Policy Act of 1978 (``NGPA''). Jefferson Island proposes to revise its SOC to provide its customers the option to use pooling points as additional points...

The 4th Generation Light Source at Jefferson Lab

International Nuclear Information System (INIS)

Stephen Benson; George Biallas; James Boyce; Donald Bullard; James Coleman; David Douglas; H. Dylla; Richard Evans; Pavel Evtushenko; Albert Grippo; Christopher Gould; Joseph Gubeli; David Hardy; Carlos Hernandez-Garcia; Kevin Jordan; John Klopf; Steven Moore; George Neil; Thomas Powers; Joseph Preble; Daniel Sexton; Michelle Shinn; Christopher Tennant; Richard Walker; Shukui Zhang; Gwyn Williams

2007-01-01

A number of 'Grand Challenges' in Science have recently been identified in reports from The National Academy of Sciences, and the U.S. Dept. of Energy, Basic Energy Sciences. Many of these require a new generation of linac-based light source to study dynamical and non-linear phenomena in nanoscale samples. In this paper we present a summary of the properties of such light sources, comparing them with existing sources, and then describing in more detail a specific source at Jefferson Lab. Importantly, the JLab light source has developed some novel technology which is a critical enabler for other new light sources

77 FR 47874 - National Register of Historic Places; Notification of Pending Nominations and Related Actions

Science.gov (United States)

2012-08-10

... Hall County Alta Vista Cemetery, 521 Jones St., Gainesville, 12000551 Troup County Eastside Historic...), 401 Jefferson, La Grange, 12000562 New Madrid County Hunter-Dawson House, 312 Dawson Rd., New Madrid... Puerto Rico TR), Georgetti St. No. 1, Barceloneta, 12000583 Cidra Municipality La Bolero (Early...

Adoption and failure of the "Boyer model" at the University of Louisville.

Science.gov (United States)

Schweitzer, L

2000-09-01

In the 1990s two factors had a major impact on the promotion and tenure process at the University of Louisville (UL) School of Medicine. Clinical reimbursements declined, and as they did, faculty hired as income-generating clinicians continued to be evaluated as researchers. In addition, with legislation ending mandatory retirement, accountability and the requirement for demonstrations of continued competency increased. In part because of the need to recognize service and the need to evaluate post-tenure faculty, the Board of Trustees launched several ambitious initiatives that were collectively entitled "Redefinition of Faculty." The eventual acceptance of the policies under this umbrella included the adoption of the four kinds of scholarship defined by Ernest Boyer. However, because of faculty unrest regarding other facets of this initiative, compromises in the way that the Boyer model was adopted rendered the governance documents untenable. The difficulties with how the UL School of Medicine adopted the Boyer model are detailed, as are some of the lessons learned. Despite the difficulties, the concepts in Boyer's treatise have not been abandoned; the UL School of Medicine has embraced the need for a broadened view of scholarship in its newly emerging governance documents in which, for example, clinical service, formerly unrecognized as a promotable activity, is now recognized as such.

The Reverend Thomas Jefferson Bowen: An Introductory Background to His Linguistic Works, 1850-1856

Science.gov (United States)

Awoniyi, Timothy A.

1974-01-01

A historical narrative background for the linguistic works of Thomas Jefferson Bowen, an American missionary who was the first non-Nigerian to publish a grammar of Yoruba (1858). The author points up a need for further scholarly review of Bowen's pioneering work and contribution to Yoruba studies. (JT)

Jefferson Davis and the Failure of Confederate Military Strategy, 1861-1865

Science.gov (United States)

2010-04-14

seventeen. Here he first met some of the men who later held key roles in the Confederate Army: Albert Sidney Johnston, Leonidas Polk, and later Robert...General Lee’s magnificent Army ofNorthem Virginia. Throughout the war Jefferson Davis failed to assign to any theater and entirely subsidiary role ...fight. 24 0 ENDNOTES 1 A. H. McDannald, B.L., ed., The Modern Concise Encyclopedia, vol. III, (New York: Unicorn Press, 1941), 490-491. 2 Harry

MeV Mott polarimetry at Jefferson Lab

International Nuclear Information System (INIS)

Steigerwald, M.

2001-01-01

In the recent past, Mott polarimetry has been employed only at low electron beam energies (≅100 keV). Shortly after J. Sromicki demonstrated the first Mott scattering experiment on lead foils at 14 MeV (MAMI, 1994), a high energy Mott scattering polarimeter was developed at Thomas Jefferson National Accelerator Facility (5 MeV, 1995). An instrumental precision of 0.5% was achieved due to dramatic improvement in eliminating the background signal by means of collimation, shielding, time of flight and coincidence methods. Measurements for gold targets between 0.05 μm and 5 μm for electron energies between 2 and 8 MeV are presented. A model was developed to explain the depolarization effects in the target foils due to double scattering. The instrumental helicity correlated asymmetries were measured to smaller than 0.1%

RICH Detector for Jefferson Labs CLAS12

Science.gov (United States)

Trotta, Richard; Torisky, Ben; Benmokhtar, Fatiha

2015-10-01

Jefferson Lab (Jlab) is performing a large-scale upgrade to its Continuous Electron Beam Accelerator Facility (CEBAF) up to 12GeV beams. The Large Acceptance Spectrometer (CLAS12) in Hall B is being upgraded and a new hybrid Ring Imaging Cherenkov (RICH) detector is being developed to provide better kaon - pion separation throughout the 3 to 8 GeV/c momentum range. This detector will be used for a variety of Semi-Inclusive Deep Inelastic Scattering experiments. Cherenkov light can be accurately detected by a large array of sophisticated Multi-Anode Photomultiplier Tubes (MA-PMT) and heavier particles, like kaons, will span the inner radii. We are presenting our work on the creation of the RICH's geometry within the CLAS12 java framework. This development is crucial for future calibration, reconstructions and analysis of the detector.

Decontamination sheet

International Nuclear Information System (INIS)

Hirose, Emiko; Kanesaki, Ken.

1995-01-01

The decontamination sheet of the present invention is formed by applying an adhesive on one surface of a polymer sheet and releasably appending a plurality of curing sheets. In addition, perforated lines are formed on the sheet, and a decontaminating agent is incorporated in the adhesive. This can reduce the number of curing operation steps when a plurality steps of operations for radiation decontamination equipments are performed, and further, the amount of wastes of the cured sheets, and operator's exposure are reduced, as well as an efficiency of the curing operation can be improved, and propagation of contamination can be prevented. (T.M.)

Challenges in Soft Computing: Case Study with Louisville MSD CSO Modeling

Science.gov (United States)

Ormsbee, L.; Tufail, M.

2005-12-01

The principal constituents of soft computing include fuzzy logic, neural computing, evolutionary computation, machine learning, and probabilistic reasoning. There are numerous applications of these constituents (both individually and combination of two or more) in the area of water resources and environmental systems. These range from development of data driven models to optimal control strategies to assist in more informed and intelligent decision making process. Availability of data is critical to such applications and having scarce data may lead to models that do not represent the response function over the entire domain. At the same time, too much data has a tendency to lead to over-constraining of the problem. This paper will describe the application of a subset of these soft computing techniques (neural computing and genetic algorithms) to the Beargrass Creek watershed in Louisville, Kentucky. The application include development of inductive models as substitutes for more complex process-based models to predict water quality of key constituents (such as dissolved oxygen) and use them in an optimization framework for optimal load reductions. Such a process will facilitate the development of total maximum daily loads for the impaired water bodies in the watershed. Some of the challenges faced in this application include 1) uncertainty in data sets, 2) model application, and 3) development of cause-and-effect relationships between water quality constituents and watershed parameters through use of inductive models. The paper will discuss these challenges and how they affect the desired goals of the project.

Preserve America Communities and Neighborhoods

Science.gov (United States)

Lemont Lockport Moline Oak Park Palestine Plainfield Rock Island Riverside Will County Woodstock Indiana Lewiston Portland Rockland Saco Sanford Skowhegan Maryland Annapolis Baltimore Calvert County Charles Excelsior Springs Florissant Fredericktown Independence Jefferson City Liberty Rocheport Saint Charles

78 FR 43916 - National Register of Historic Places; Notification of Pending Nominations and Related Actions

Science.gov (United States)

2013-07-22

...) Ave. P, .75 mi. W. of 30th Rd., Little River, 13000580 Santa Fe Trail--Rice County Segment 3, (Santa... MISSOURI St. Charles County Link, Oliver L. and Catherine, House, 1005 Jefferson, St. Charles, 13000584 NEW... Manitowoc County Klingholz, Charles and Herriette, House, 224 Mill Rd., Manitowoc Rapids, 13000587 Waukesha...

Moeller polarimeter in the hall a jefferson lab after reconstruction

International Nuclear Information System (INIS)

Pomatsalyuk, R.I.

2016-01-01

The Moller polarimeter in the Hall A of Jefferson Lab was reconstructed in order to expand of the energy range of the polarimeter to measure the polarization of the electron beam with an energy up to 11.5 GeV. The paper de-scribes the main results of the Moller polarimeter testing after reconstruction. The measurements of the electrons polarization were provided by two data acquisition systems operating in parallel. The testing of the shielding insertion of magnetic dipole has been performed. The way to eliminate detected deviations in the operation of polarimeter during test is shown.

77 FR 2120 - Environmental Impact Statement for New Orleans Rail Gateway (NORG), Jefferson and Orleans...

Science.gov (United States)

2012-01-13

... Xavier University of Louisiana, University Center, 3rd Floor, Mary and William McCaffrey Ballroom B, 4980..., Council Chambers, 1221 Elmwood Park Boulevard, Jefferson, LA 70123 Information on the meeting locations is... Press Drive and then continuing eastward along Dwyer Road; on the east along Maxent Canal near Bayou...

Jefferson Lab IR demo FEL photocathode quantum efficiency scanner

CERN Document Server

Gubeli, J; Grippo, A; Jordan, K; Shinn, M; Siggins, T

2001-01-01

Jefferson Laboratory's Free Electron Laser (FEL) incorporates a cesiated gallium arsenide (GaAs) DC photocathode gun as its electron source. By using a set of scanning mirrors, the surface of the GaAs wafer is illuminated with a 543.5nm helium-neon laser. Measuring the current flow across the biased photocathode generates a quantum efficiency (QE) map of the 1-in. diameter wafer surface. The resulting QE map provides a very detailed picture of the efficiency of the wafer surface. By generating a QE map in a matter of minutes, the photocathode scanner has proven to be an exceptional tool in quickly determining sensitivity and availability of the photocathode for operation.

Present and future of hadron spectroscopy at Jefferson Lab

CERN Document Server

Battaglieri, M

2010-01-01

The CLAS Collaboration is operating the CLAS detector at theThomas Jefferson National Laboratory (JLab) in USA. The unique combination of the detector large acceptance and high intensity of the continuous electron beam of CEBAF has opened the way to a comprehensive study of the hadrons structure in kinematic domain between nuclear and particle physics. Hadron spectroscopy plays a central role in the physics program of the Collaboration. Many exclusive channels have been studied with virtual and real photon beams in a wide kinematic providing key information about the hadron structure as well as the reactions dynamic. In this contribution, the rich physics program covered by present and future experiments will be reviewed.

Photoproduction of the f1(1285)/η(1295) Mesons using CLAS at Jefferson Lab

Energy Technology Data Exchange (ETDEWEB)

Dickson, Ryan [Carnegie Mellon Univ., Pittsburgh, PA (United States)

2011-07-18

This work presents the results of analysis of a meson mass m_x =1281.0 ± 0.8 MeV/ c² and a FWHM of Γ_x = 18.4 ± 1.4 MeV/ c² seen in CLAS at Jefferson Lab in photoproduction off the proton, γp → xp.

CLAS+FROST: new generation of photoproduction experiments at jefferson lab

International Nuclear Information System (INIS)

Pasyuk, E.

2009-01-01

A large part of the experimental program in Hall B of the Jefferson Lab is dedicated to baryon spectroscopy. Photoproduction experiments are essential part of this program. CEBAF Large Acceptance Spectrometer (CLAS) and availability of circularly and linearly polarized tagged photon beams provide unique conditions for this type of experiments. Recent addition of the Frozen Spin Target (FROST) gives a remarkable opportunity to measure double and triple polarization observables for different pseudo-scalar meson photoproduction processes. For the first time, a complete or nearly complete experiment becomes possible and will allow model independent extraction of the reaction amplitude. An overview of the experiment and its current status is presented. (author)

Residual Resistance Data from Cavity Production Projects at Jefferson Lab

International Nuclear Information System (INIS)

Ciovati, Gianluigi; Geng, Rongli; Mammosser, John; Saunders, Jeffrey

2010-01-01

A fundamental limitation towards achieving high quality factors in superconducting radio-frequency cavities is the so-called residual resistance. Understanding and controlling the residual resistance has important implications towards improving the efficiency and reduce the operating cost of continuous wave superconducting linear accelerators. In this contribution we will report on the residual resistance values obtained from measurements of the quality factor of a large set of cavities, with resonant frequency between 805 MHz and 1.5 GHz, all of them processed and tested at Jefferson Lab. Surface treatments included both buffered chemical polishing and electropolishing. The results indicate an approximate value of the residual resistance of about 7-10 n Omega.

Electro- and Photoproduction of Omega(783) Mesons using CLAS at Jefferson Lab

International Nuclear Information System (INIS)

Manak, J.J.; Volker Burkert; Franz Klein; Bernhard Mecking; Alan Coleman; Herb Funsten

2000-01-01

Electro- and photoproduction of w(783) from a proton target have been measured in the CLAS detector at the Thomas Jefferson National Accelerator Facility in Newport News VA. The photoproduction data were taken over a photon energy range from 0.5 to 2.3 GeV, while the electroproduction data was obtained over a W range of 1.8-2.5 GeV/c2. Preliminary acceptance corrected center-of-mass angular distributions have been examined for both data sets

Cyclic platform dolomites and platform-to-basin transition of Jefferson Formation (Frasnian), southwest Montana and east-central Idaho

Energy Technology Data Exchange (ETDEWEB)

Dorobek, S.L.

1987-08-01

The Jefferson Formation (Frasnian) in southwestern Montana consists of cyclic sequences of shallow marine platformal dolomites that grade westward into slope/basinal facies in east-central Idaho. Regional sedimentologic characteristics of slope facies in Idaho indicate that the Jefferson platform resembled a distally steepened ramp. Slope facies consist of slope laminites with local small scale slumps and slope breccias. Shallow water platform-derived clasts are lacking in the slope breccias. Individual shallowing upward platform cycles are 25 m to < 1 m thick and consists of, in descending order: local solution-collapse breccia caps; cryptalgal dolomudstone; rare ooid dolograinstone; thin-bedded Amphipora dolowackestone; coarsely crystalline dolostones with abundant lenticular to domal stromatoporoids; and basal thin-bedded, fine-grained, shale dolostones with closely spaced hard-grounds that grade upward into burrow-homogenized, irregularly bedded dolostones.

Hadronic Multi-Particle Final State Measurements with CLAS at Jefferson Lab

International Nuclear Information System (INIS)

Will Brooks

2002-01-01

Precision measurements in the neutrino sector are becoming increasingly feasible due to the development of relatively high-rate experimental capabilities. These important developments command renewed attention to the systematic corrections needed to interpret the data. Hadronic multi-particle final state measurements made using CLAS at Jefferson Lab, together with a broad theoretical effort that links electro-nucleus and neutrino-nucleus data, will address this problem, and will elucidate long-standing problems in intermediate energy nuclear physics. This new work will ultimately enable precision determinations of fundamental quantities such as the neutrino mixing matrix elements in detailed studies of neutrino oscillations

Spectroscopic Study of L Hypernuclei with Electron Beams at Jefferson Lab

Energy Technology Data Exchange (ETDEWEB)

Nakamura, Satoshi [Tohoku Univ., Sendai (Japan); Gogami, Toshiyuki [Tohoku Univ., Sendai (Japan); Tang, Liguang [Hampton Univ., Hampton, VA (United States); Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States)

2017-07-01

The missing mass spectroscopy of L hypernuclei with the (e, e'K^+) reaction was started from 2000 at Jefferson Lab. In this fifteen years, various hypernuclei (A = 7 - 52) including hyperon (L, S^0) productions have been studied with newly developed experimental techniques. The (e, e'K^+) reaction spectroscopy of L hypernuclei features its capability of absolute missing mass calibration and production of new species of hypernuclei which are the isospin partners of well studied hypernuclei by (K^-, pi-) and (pi^+, K^+) reactions. In this paper, we will review how we established the (e, e'K^+) spectroscopic study of hypernuclei.

Dense sheet Z-pinches

International Nuclear Information System (INIS)

Tetsu, Miyamoto

1999-01-01

The steady state and quasi-steady processes of infinite- and finite-width sheet z-pinches are studied. The relations corresponding to the Bennett relation and Pease-Braginskii current of cylindrical fiber z-pinches depend on a geometrical factor in the sheet z-pinches. The finite-width sheet z-pinch is approximated by a segment of infinite-width sheet z-pinch, if it is wide enough, and corresponds to a number of (width/thickness) times fiber z-pinch plasmas of the diameter that equals the sheet thickness. If the sheet current equals this number times the fiber current, the plasma created in the sheet z-pinches is as dense as in the fiber z-pinches. The total energy of plasma and magnetic field per unit mass is approximately equal in both pinches. Quasi-static transient processes are different in several aspects from the fiber z-pinch. No radiation collapse occurs in the sheet z-pinch. The stability is improved in the sheet z-pinches. The fusion criterions and the experimental arrangements to produce the sheet z-pinches are also discussed. (author)

Geology and mining history of the Southeast Missouri Barite District and the Valles Mines, Washington, Jefferson, and St. Francois Counties, Missouri

Science.gov (United States)

Mugel, Douglas N.

2017-03-09

The Southeast Missouri Barite District and the Valles Mines are located in Washington, Jefferson, and St. Francois Counties, Missouri, where barite and lead ore are present together in surficial and near-surface deposits. Lead mining in the area began in the early 1700’s and extended into the early 1900’s. Hand mining of lead in the residuum resulted in widespread pits (also called shafts or diggings), and there was some underground mining of lead in bedrock. By the 1860’s barite was recovered from the residuum by hand mining, also resulting in widespread diggings, but generally not underground mines in bedrock. Mechanized open-pit mining of the residuum for barite began in the 1920’s. Barite production slowed by the 1980’s, and there has not been any barite mining since 1998. Mechanized barite mining resulted in large mined areas and tailings ponds containing waste from barite mills.The U.S. Environmental Protection Agency (EPA) has determined that lead is present in surface soils in Washington and Jefferson Counties at concentrations exceeding health-based screening levels. Also, elevated concentrations of barium, arsenic, and cadmium have been identified in surface soils, and lead concentrations exceeding the Federal drinking-water standard of 15 micrograms per liter have been identified in private drinking-water wells. Potential sources of these contaminants are wastes associated with barite mining, wastes associated with lead mining, or unmined natural deposits of barium, lead, and other metals. As a first step in helping EPA determine the source of soil and groundwater contamination, the U.S. Geological Survey (USGS), in cooperation with the EPA, investigated the geology and mining history of the Southeast Missouri Barite District and the Valles Mines.Ore minerals are barite (barium sulfate), galena (lead sulfide), cerussite (lead carbonate), anglesite (lead sulfate), sphalerite (zinc sulfide), smithsonite (zinc carbonate), and chalcopyrite (copper

OrthoImagery Submission for Jefferson County, GA

Data.gov (United States)

Federal Emergency Management Agency, Department of Homeland Security — NAIP imagery is available for distribution within 60 days of the end of a flying season and is intended to provide current information of agricultural conditions in...

Jefferson Lab IEC 61508/61511 Safety PLC Based Safety System

International Nuclear Information System (INIS)

Mahoney, Kelly; Robertson, Henry

2009-01-01

This paper describes the design of the new 12 GeV Upgrade Personnel Safety System (PSS) at the Thomas Jefferson National Accelerator Facility (TJNAF). The new PSS design is based on the implementation of systems designed to meet international standards IEC61508 and IEC 61511 for programmable safety systems. In order to meet the IEC standards, TJNAF engineers evaluated several SIL 3 Safety PLCs before deciding on an optimal architecture. In addition to hardware considerations, software quality standards and practices must also be considered. Finally, we will discuss R and D that may lead to both high safety reliability and high machine availability that may be applicable to future accelerators such as the ILC.

77 FR 71828 - National Register of Historic Places; Notification of Pending Nominations and Related Actions

Science.gov (United States)

2012-12-04

... School, (Indiana's Public Common and High Schools MPS) 550 E. Jefferson St., Franklin, 12001058 La Porte County Ames Family Homestead, 5332 & 5336 W. 150 N., La Porte, 12001062 Lake County Roosevelt, Theodore...), Portions of Boyle, Chouteau, Kentucky, Norfolk, Swan, Talmadge, Tower Grove, Vandeventer & Vista, St. Louis...

Hospital Web site 'tops' in Louisiana. Hospital PR, marketing group cites East Jefferson General Hospital.

Science.gov (United States)

Rees, Tom

2002-01-01

East Jefferson General Hospital in Metairie, La., launched a new Web site in October 2001. Its user-friendly home page offers links to hospital services, medical staff, and employer information. Its jobline is a powerful tool for recruitment. The site was awarded the 2002 Pelican Award for Best Consumer Web site by the Louisiana Society for Hospital Public Relations & Marketing.

Analysis of Deeply Virtual Compton Scattering data at Jefferson Lab and proton tomography

Energy Technology Data Exchange (ETDEWEB)

Dupre, R.; Guidal, M.; Niccolai, S. [Institut de Physique Nucleaire d' Orsay, CNRS-IN2P3, Universite Paris-Sud, Universite Paris-Saclay, Orsay (France); Vanderhaeghen, M. [Johannes Gutenberg-Universitaet, Institut fuer Kernphysik und PRISMA Cluster of Excellence, Mainz (Germany)

2017-08-15

The CLAS and Hall A Collaborations at Jefferson Laboratory have recently released new results for the ep → epγ reaction. We analyze these new data within the Generalized Parton Distribution formalism. Employing a fitter algorithm introduced and used in earlier works, we are able to extract from these data new constraints on the kinematical dependence of three Compton Form Factors. Based on experimental data, we subsequently extract the dependence of the proton charge radius on the quarks' longitudinal momentum fraction. (orig.)

78 FR 20334 - Changes in Flood Hazard Determinations

Science.gov (United States)

2013-04-04

..., City of Department, 1905 index.php/alabama/ Gulf Shores, P.O. West 1st Street, baldwin/. Box 299, Gulf... www.bakeraecom.com/ Appelbaum, Mayor, Broadway Street, index.php/colorado/ City of Boulder, Boulder....com/ County (12-08- Chairman, Planning and index.php/colorado/ 0863P). Jefferson County Zoning, 100...

77 FR 44268 - National Register of Historic Places; Notification of Pending Nominations and Related Actions

Science.gov (United States)

2012-07-27

... Presbyterian Church of Peoria, 10236 N. 83rd Ave., Peoria, 12000493 CALIFORNIA Mariposa County Half Dome Cables and Trail, P.O. Box 577, Yosemite, 12000494 COLORADO Jefferson County Baugh, James H., House, 11361 W... Dome Observation Tower, Terminus of Clingmans Dome Rd., Bryson City, 12000515 SOUTH DAKOTA Lawrence...

Scorpion envenomation study in Behbahan County, Southwest Iran

Directory of Open Access Journals (Sweden)

Hamid Kassiri

2014-05-01

Full Text Available Objective: To study the incidence and epidemiology of scorpion sting cases that were referred to the health services centers of Behbahan County, Khuzistan Province, southwestern Iran, during the two yeare (2007-2008. Methods: In this descriptive retrospective research, the data has come from files of scorpionstung patients referring to the health services centers of Behbahan during study period. A special scorpion sting sheet was prepared and completed for every case of scorpion sting. Analysis of 3441 case sheets received during this period was carried out. The frequencies of medical and entomoepidemiologic parameters were turned to the percentage position. Results: A total of 3 441 cases of scorpion stings were reported during the two-year period from 2007 to 2008. The average incidence of scorpion stings was 8.8‰ in the two years. The frequency of cases was higher during August, September, June and July that 2 056 cases of scorpion stings were reported. Most stings were occurred during summer. Nearly 51.3% of the cases were men. All cases had received antivenin. Majority of scorpion sting cases (56.5% lived in the rural areas. The most common sting site was the hand. About 74.4% have received the antivenin 0-6 h after the sting. The early injection of the antivenin is very important. The most of the cases of scorpion stings (59% were occurred by yellow scorpions. Conclusions: Surveillance for cases of scorpion stings must begin at all regions of Behbahan County. Treatment of cases of scorpion stings is conducted according to a protocol set by the Ministry of Health, Treatment and Medical Education. This protocol included directions for lines of treatment and the dose of antivenin recommended. Thereafter all cases are referred to hospital for further observation and management.

Jefferson Lab mass storage and file replication services

International Nuclear Information System (INIS)

Bird, I.; Chen, Y.; Hess, B.; Kowalski, A.; Watson, C.

2001-01-01

Jefferson Lab has implemented a scalable, distributed, high performance mass storage system-JASMine. The system is entirely implemented in Java, provides access to robotic tape storage and includes disk cache and stage manager components. The disk manager subsystem may be used independently to manage stand-alone disk pools. The system includes a scheduler to provide policy-based access to the storage systems. Security is provided by pluggable authentication modules and it implemented at the network socket level. The tape and disk cache systems have well defined interfaces in order to provide integration with grid-based services. The system is in production and being used to archive 1 TB per day from the experiments, and currently moves over 2 TB per day total. The authors will describe the architecture of JASMine; discuss the rationale for building the system, and present a transparent 3 rd party file replication service to move data to collaborating institutes using JASMine, XML, and servlet technology interfacing to grid-based file transfer mechanisms

Deeply Virtual Compton Scattering Studies at Jefferson Lab

International Nuclear Information System (INIS)

Sabatie, F.

2010-11-01

This document describes the early experimental effort at Jefferson Lab to unravel the Generalized Parton Distributions (GPD), using the Deeply Virtual Compton Scattering (DVCS) process. The GPDs contain the usual form factors and parton distribution functions, but in addition, they include correlations between states of different longitudinal and transverse momenta. They therefore give access to a three-dimensional picture of the nucleon. DVCS is the cleanest process allowing to extract GPDs, and as early as 2000, a number of experiments were proposed for this purpose. The results of the first exploratory experiments are presented as well as the first measurements of linear combinations of GPDs. In addition, a thorough discussion on the insights gained from these early experiments is proposed, linked with the theoretical tools used to extract GPDs from DVCS data. Finally, improvements on what was done for this first experimental phase are proposed and discussed, and new proposals and measurements are described. (author)

Policies and Procedures for Foreign Exchange Agencies. First Edition.

Science.gov (United States)

Hartman, Donald D.

The guide details the policy of the Jefferson County (Alabama) Board of Education policy concerning international exchange of students (travel both to and from United States) in elementary and secondary grades. The first section specifies the standards by which the county will evaluate all international exchange agencies concerning structure,…

Timber resource statistics for all forest land, except national forests, in eastern Oregon.

Science.gov (United States)

Donald R. Gedney; Patricia M. Bassett; Mary A. Mei

1989-01-01

This report summarizes a 1987 timber resource inventory of all forest land, except National Forests, in the 17 counties (Baker, Crook, Deschutes, Gilliam, Grant, Harney, Jefferson, Klamath, Lake, Malheur, Morrow, Sherman, Umatilla, Union, Wallowa, Wasco, and Wheeler Counties) in eastern Oregon. Detailed tables of forest area, timber volume, growth, mortality, and...

Deeply virtual Compton scattering in the Hall A of Jefferson laboratory; Diffusion Compton profondement virtuelle dans le Hall A au Jefferson laboratory

Energy Technology Data Exchange (ETDEWEB)

Munoz Camacho, C

2005-12-15

Generalized Parton Distributions (GPDs), introduced in the late 90's, provide a universal description of hadrons in terms of the underlying degrees of freedom of Quantum Chromodynamics: quarks and gluons. GPDs appear in a wide variety of hard exclusive reactions and the advent of high luminosity accelerator facilities has made the study of GPDs accessible to experiment. Deeply Virtual Compton Scattering (DVCS) is the golden process involving GPDs. The first dedicated DVCS experiment ran in the Hall A of Jefferson Lab in Fall 2004. An electromagnetic calorimeter and a plastic scintillator detector were constructed for this experiment, together with specific electronics and acquisition system. The experiment preparation, data taking and analysis are described in this document. Results on the absolute cross section difference for opposite beam helicities provide the first measurement of a linear combination of GPDs as a function of the momentum transfer to the nucleon. (author)

Electromagnetic calorimeter for the Heavy Photon Search Experiment at Jefferson Lab

Energy Technology Data Exchange (ETDEWEB)

Buchanan, Emma [Univ. of Glasgow, Scotland (United Kingdom)

2014-11-01

The Heavy Photon Search Experiment (HPS) seeks to detect a hypothesised hidden sector boson, the A', predicted to be produced in dark matter decay or annihilation. Theories suggest that the A' couples weakly to electric charge through kinetic mixing, allowing it, as a result, to decay to Standard Matter (SM) lepton pair, which may explain the electron and positron excess recently observed in cosmic rays. Measuring the lepton pair decay of the A' could lead to indirect detection of dark matter. The HPS experiment is a fixed target experiment that will utilize the electron beam produced at the Thomas Jefferson National Accelerator Facility (Jefferson Lab). The detector set-up includes a silicon vertex tracker (SVT) and an Electromagnetic Calorimeter (ECal). The ECal will provide the trigger and detect e+e- pairs and its construction and testing forms the focus of this thesis. The ECal consists of 442 PbWO₄- tapered crystals with a length 16cm and a 1.6x1.6cm² cross-section, stacked into a rectangular array and are coupled to Large Area APDs and corresponding pre-amplifiers. Supplementary to the ECal is a Light Monitoring System (LMS) consisting of bi-coloured LEDs that will monitor changes in APD gain and crystal transparency due to radiation damage. Before construction of the ECal each of the components were required to be individually tested to determine a number of different characteristics. Irradiation tests were performed on PbWO₄ ECal crystals and, as a comparison, one grown by a different manufacturer to determine their radiation hardness. A technique for annealing the radiation damage by optical bleaching, which involves injecting light of various wavelengths into the crystal, was tested using the blue LED from the LMS as a potential candidate. The light yield dependence on temperature was also measured for one of the PbWO₄ crystal types. Each APD was individually tested to determine if they

Aerial gamma ray and magnetic survey, Jefferson City Quadrangle, Missouri. Final report

International Nuclear Information System (INIS)

1980-11-01

The Jefferson City quadrangle covers approximately 7500 square miles at the Northwestern end of the Ozark uplift. Lithified material exposed, ranges in age from Cambrian through Pennsylvanian, but Pennsylvanian sediments dominate the surface as mapped. Some alluvium is mapped in river flood plain areas. A search of available literature revealed no known uranium deposits. A total of 95 uranium anomalies were detected and are discussed briefly in this report. All anomalies are related to cultural features, but those associated with coal mine tailings appear to have some significance. Magnetic data appear to relate to complexities in the underlying Precambrian rocks

A RICH detector for strangeness physics in Hall A at Jefferson Lab

International Nuclear Information System (INIS)

Cusanno, F.; Garibaldi, F.; Cisbani, E.; Colilli, S.; De Cataldo, G.; De Leo, R.; Giuliani, F.; Gricia, M.; Lagamba, L.; Lucentini, M.; Reitz, B.; Santavenere, F.; Urciuoli, G.M.

2004-01-01

The high-resolution hypernuclear spectroscopy experiment at Jefferson Lab, Hall A (E94-107), needs unambiguous kaon identification. Due to the huge pion and proton background, the standard Hall A hadron particle identification, based on a time of flight and two aerogel threshold Cherenkov detectors, is not sufficient. For this task a proximity focusing C 6 F 14 /CsI RICH has been built. Recently, after some improvements to the mechanical structure of its wire chamber and to its electronics rate capability, the RICH has been tested with cosmic rays. This paper represents a status report of the RICH detector

Relation between current sheets and vortex sheets in stationary incompressible MHD

Directory of Open Access Journals (Sweden)

D. H. Nickeler

2012-03-01

Full Text Available Magnetohydrodynamic configurations with strong localized current concentrations and vortices play an important role in the dissipation of energy in space and astrophysical plasma. Within this work we investigate the relation between current sheets and vortex sheets in incompressible, stationary equilibria. For this approach it is helpful that the similar mathematical structure of magnetohydrostatics and stationary incompressible hydrodynamics allows us to transform static equilibria into stationary ones. The main control function for such a transformation is the profile of the Alfvén-Mach number MA, which is always constant along magnetic field lines, but can change from one field line to another. In the case of a global constant MA, vortices and electric current concentrations are parallel. More interesting is the nonlinear case, where MA varies perpendicular to the field lines. This is a typical situation at boundary layers like the magnetopause, heliopause, the solar wind flowing around helmet streamers and at the boundary of solar coronal holes. The corresponding current and vortex sheets show in some cases also an alignment, but not in every case. For special density distributions in 2-D, it is possible to have current but no vortex sheets. In 2-D, vortex sheets of field aligned-flows can also exist without strong current sheets, taking the limit of small Alfvén Mach numbers into account. The current sheet can vanish if the Alfvén Mach number is (almost constant and the density gradient is large across some boundary layer. It should be emphasized that the used theory is not only valid for small Alfvén Mach numbers MA MA ≲ 1. Connection to other theoretical approaches and observations and physical effects in space plasmas are presented. Differences in the various aspects of theoretical investigations of current sheets and vortex sheets are given.

76 FR 64992 - Carrollton Railroad-Abandonment Exemption-in Carroll County, KY CSX Transportation, Inc...

Science.gov (United States)

2011-10-19

... discontinue service over, approximately 0.79 miles of rail line on CSXT's Northern Region, Louisville Division... temporarily because they are not needed in common carrier service at the present time. Once the line is... formal complaint filed by a user of rail service on the line (or by a state or local government entity...

An ice sheet model validation framework for the Greenland ice sheet

Science.gov (United States)

Price, Stephen F.; Hoffman, Matthew J.; Bonin, Jennifer A.; Howat, Ian M.; Neumann, Thomas; Saba, Jack; Tezaur, Irina; Guerber, Jeffrey; Chambers, Don P.; Evans, Katherine J.; Kennedy, Joseph H.; Lenaerts, Jan; Lipscomb, William H.; Perego, Mauro; Salinger, Andrew G.; Tuminaro, Raymond S.; van den Broeke, Michiel R.; Nowicki, Sophie M. J.

2017-01-01

We propose a new ice sheet model validation framework - the Cryospheric Model Comparison Tool (CmCt) - that takes advantage of ice sheet altimetry and gravimetry observations collected over the past several decades and is applied here to modeling of the Greenland ice sheet. We use realistic simulations performed with the Community Ice Sheet Model (CISM) along with two idealized, non-dynamic models to demonstrate the framework and its use. Dynamic simulations with CISM are forced from 1991 to 2013, using combinations of reanalysis-based surface mass balance and observations of outlet glacier flux change. We propose and demonstrate qualitative and quantitative metrics for use in evaluating the different model simulations against the observations. We find that the altimetry observations used here are largely ambiguous in terms of their ability to distinguish one simulation from another. Based on basin-scale and whole-ice-sheet-scale metrics, we find that simulations using both idealized conceptual models and dynamic, numerical models provide an equally reasonable representation of the ice sheet surface (mean elevation differences of framework demonstrates that our proposed metrics can distinguish relatively better from relatively worse simulations and that dynamic ice sheet models, when appropriately initialized and forced with the right boundary conditions, demonstrate a predictive skill with respect to observed dynamic changes that have occurred on Greenland over the past few decades. An extensible design will allow for continued use of the CmCt as future altimetry, gravimetry, and other remotely sensed data become available for use in ice sheet model validation.

Deeply virtual Compton scattering at Jefferson Laboratory

Energy Technology Data Exchange (ETDEWEB)

Biselli, Angela S. [Fairfield University - Department of Physics 1073 North Benson Road, Fairfield, CT 06430, USA; Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States)

2016-08-01

The generalized parton distributions (GPDs) have emerged as a universal tool to describe hadrons in terms of their elementary constituents, the quarks and the gluons. Deeply virtual Compton scattering (DVCS) on a proton or neutron ($N$), $e N \\rightarrow e' N' \\gamma$, is the process more directly interpretable in terms of GPDs. The amplitudes of DVCS and Bethe-Heitler, the process where a photon is emitted by either the incident or scattered electron, can be accessed via cross-section measurements or exploiting their interference which gives rise to spin asymmetries. Spin asymmetries, cross sections and cross-section differences can be connected to different combinations of the four leading-twist GPDs (${H}$, ${E}$, ${\\tilde{H}}$, ${\\tilde{E}}$) for each quark flavors, depending on the observable and on the type of target. This paper gives an overview of recent experimental results obtained for DVCS at Jefferson Laboratory in the halls A and B. Several experiments have been done extracting DVCS observables over large kinematics regions. Multiple measurements with overlapping kinematic regions allow to perform a quasi-model independent extraction of the Compton form factors, which are GPDs integrals, revealing a 3D image of the nucleon.

Late Albian dinosaur tracks from the cratonic (eastern) margin of the Western Interior Seaway, Nebraska, USA

Science.gov (United States)

Joeckel, R.M.; Cunningham, J.M.; Corner, R.G.; Brown, G.W.; Phillips, P.L.; Ludvigson, Greg A.

2004-01-01

At least 22 tridactyl dinosaur tracks, poorly preserved in various degrees of expression, have recently been found at an exposure in the Dakota Formation (Lower Cretaceous, Albian) in Jefferson County, Nebraska. These tracks generally have broad, blunt digits and a broad posterior margin. The largest of the tracks measures 57 cm in length and 58 cm in width. All of the tracks lie within a stratigraphic horizon of 40 cm or less, but they do not form a single trackway. We interpret the trackmakers to have been ornithopods.The Jefferson County tracks are in a well-cemented sandstone with oscillation ripples, at a stratigraphic level between two well-established sequence boundaries. Channel forms and lateral accretion units are common in the stratigraphic interval enclosing the tracks, and the site is interpreted as a bar or sand flat in a tidally influenced river.The Jefferson County tracks are only the second known occurrence of large Mesozoic tetrapod tracks east of the Rocky Mountain Front-High Plains Margin, including the Black Hills of South Dakota, west of the Atlantic Coastal Plain, and north of the Gulf Coastal Plain. Further, this paper is the first documentation of in situdinosaur fossils from the Nebraska-Iowa area.

A composite thin vacuum window for the CLAS photon tagger at Jefferson lab

International Nuclear Information System (INIS)

Matthews, S.K.; Crannell, Hall; O'Brien, J.T.; Sober, D.I.

1999-01-01

The construction of a thin vacuum window, currently in use on the CLAS photon tagging system at the Thomas Jefferson National Accelerator Facility, is described. A layer of woven Kevlar cloth supports a much thinner membrane of aluminized Mylar. Notable features of this particular window include its overall length (9.6 m), and the fact that the entire load is supported by the epoxy seal with no mechanical clamping around the edges. Results from a diverse program of materials testing, including a clear dependence of leak rate on relative humidity, are also reported

A composite thin vacuum window for the CLAS photon tagger at Jefferson lab

CERN Document Server

Matthews, S K; O'Brien, J T; Sober, D I

1999-01-01

The construction of a thin vacuum window, currently in use on the CLAS photon tagging system at the Thomas Jefferson National Accelerator Facility, is described. A layer of woven Kevlar cloth supports a much thinner membrane of aluminized Mylar. Notable features of this particular window include its overall length (9.6 m), and the fact that the entire load is supported by the epoxy seal with no mechanical clamping around the edges. Results from a diverse program of materials testing, including a clear dependence of leak rate on relative humidity, are also reported.

Chlamydia - CDC Fact Sheet

Science.gov (United States)

... Archive STDs Home Page Bacterial Vaginosis (BV) Chlamydia Gonorrhea Genital Herpes Hepatitis HIV/AIDS & STDs Human Papillomavirus ( ... sheet Pelvic Inflammatory Disease (PID) – CDC fact sheet Gonorrhea – CDC fact sheet STDs Home Page Bacterial Vaginosis ( ...

Study of CSR Effects in the Jefferson Laboratory FEL Driver

Energy Technology Data Exchange (ETDEWEB)

Hall, C. C. [Colorado State U.; Biedron, S. [Colorado State U.; Burleson, Theodore A. [Colorado State U.; Milton, Stephen V. [Colorado State U.; Morin, Auralee L. [Colorado State U.; Benson, Stephen V. [JLAB; Douglas, David R. [JLAB; Evtushenko, Pavel E. [JLAB; Hannon, Fay E. [JLAB; Li, Rui [JLAB; Tennant, Christopher D. [JLAB; Zhang, Shukui [JLAB; Carlsten, Bruce E. [LANL; Lewellen, John W. [LANL

2013-08-01

In a recent experiment conducted on the Jefferson Laboratory IR FEL driver the effects of Coherent Synchrotron Radiation (CSR) on beam quality were studied. The primary goal of this work was to explore CSR output and effect on the beam with variation of the bunch compression in the IR chicane. This experiment also provides a valuable opportunity to benchmark existing CSR models in a system that may not be fully represented by a 1-D CSR model. Here we present results from this experiment and compare to initial simulations of CSR in the magnetic compression chicane of the machine. Finally, we touch upon the possibility for CSR induced microbunching gain in the magnetic compression chicane, and show that parameters in the machine are such that it should be thoroughly damped.

SANE Of Jefferson Lab: Spin Asymmetries on the Nucleon Experiment

International Nuclear Information System (INIS)

Ahmidouch, Abdellah

2011-01-01

The Spin Asymmetry on the Nucleon Experiment (SANE) at Jefferson Lab measures proton spin observables A 1 p , A 2 p and structure functions g 1 p and g 2 p over a broad range of Bjorken scaling variable x from 0.3 to 0.8, for four-momentum transfers ranging from 2.5 GeV 2 to 6.5 GeV 2 . Inclusive double spin asymmetries were measured by scattering 4.7 and 5.9-GeV longitudinally polarized electron beam off a polarized solid NH 3 target, in both parallel and near-perpendicular configuration. Scattered electrons were detected using a novel non-magnetic detector array with 194-msr acceptance. This paper presents the physics motivation for the experiment, the detector performance, and the latest status of the ongoing data analysis.

DarkLight: A Search for Dark Forces at the Jefferson Laboratory Free-Electron Laser Facility

Energy Technology Data Exchange (ETDEWEB)

Balewski, Jan; Bernauer, J; Bertozzi, William; Bessuille, Jason; Buck, B; Cowan, Ray; Dow, K; Epstein, C; Fisher, Peter; Gilad, Shalev; Ihloff, Ernest; Kahn, Yonatan; Kelleher, Aidan; Kelsey, J; Milner, Richard; Moran, C; Ou, Longwu; Russell, R; Schmookler, Barak; Thaler, J; Tschalar, C; Vidal, Christopher; Winnebeck, A; Benson, Stephen [JLAB; Gould, Christopher [JLAB; Biallas, George [JLAB; Boyce, James [JLAB; Coleman, James [JLAB; Douglas, David [JLAB; Ent, Rolf [JLAB; Evtushenko, Pavel [JLAB; Fenker, Howard [JLAB; Gubeli, Joseph [JLAB; Hannon, Fay [JLAB; Huang, Jia [JLAB; Jordan, Kevin [JLAB; Legg, Robert [JLAB; Marchlik, Matthew [JLAB; Moore, Steven [JLAB; Neil, George [JLAB; Shinn, Michelle D [JLAB; Tennant, Christopher [JLAB; Walker, Richard [JLAB; Williams, Gwyn [JLAB; Zhang, Shukui [JLAB; Freytsis, M; Fiorito, Ralph; O' Shea, P; Alarcon, Ricardo; Dipert, R; Ovanesyan, G; Gunter, Thoth; Kalantarians, Narbe; Kohl, M; Albayrak, Ibrahim; Horn, Tanja; Gunarathne, D S; Martoff, C J; Olvitt, D L; Surrow, Bernd; Lia, X; Beck, Reinhard; Schmitz, R; Walther, D; Brinkmann, K; Zaunig, H

2014-05-01

We give a short overview of the DarkLight detector concept which is designed to search for a heavy photon A' with a mass in the range 10 MeV/c^2 < m(A') < 90 MeV/c^2 and which decays to lepton pairs. We describe the intended operating environment, the Jefferson Laboratory free electon laser, and a way to extend DarkLight's reach using A' --> invisible decays.

Laminin-521 Promotes Rat Bone Marrow Mesenchymal Stem Cell Sheet Formation on Light-Induced Cell Sheet Technology

Directory of Open Access Journals (Sweden)

Zhiwei Jiang

2017-01-01

Full Text Available Rat bone marrow mesenchymal stem cell sheets (rBMSC sheets are attractive for cell-based tissue engineering. However, methods of culturing rBMSC sheets are critically limited. In order to obtain intact rBMSC sheets, a light-induced cell sheet method was used in this study. TiO2 nanodot films were coated with (TL or without (TN laminin-521. We investigated the effects of laminin-521 on rBMSCs during cell sheet culturing. The fabricated rBMSC sheets were subsequently assessed to study cell sheet viability, reattachment ability, cell sheet thickness, collagen type I deposition, and multilineage potential. The results showed that laminin-521 could promote the formation of rBMSC sheets with good viability under hyperconfluent conditions. Cell sheet thickness increased from an initial 26.7 ± 1.5 μm (day 5 up to 47.7 ± 3.0 μm (day 10. Moreover, rBMSC sheets maintained their potential of osteogenic, adipogenic, and chondrogenic differentiation. This study provides a new strategy to obtain rBMSC sheets using light-induced cell sheet technology.

Pseudospread of the atlas: false sign of Jefferson fracture in young children

International Nuclear Information System (INIS)

Suss, R.A.; Zimmerman, R.D.; Leeds, N.E.

1983-01-01

Jefferson fractures are rare prior to teen-age. Three young children examined after trauma exhibited the characteristic spread appearance of the atlas, but fractures were excluded radiographically and clinically. A retrospective study demonstrated a similar appearance, termed pseudospread, in most children aged 3 months to 4 years, including over 90% during the second year. Pseudospread results from a discrepancy between the neural growth pattern of the atlas and the somatic pattern of the axis. An atlas spread index is defined and a normal range presented. When an atlas fracture is suggested by apparent lateral spread of the lateral atlas masses, computed tomography is useful to demonstrate an intact atlas ring

County Spending

Data.gov (United States)

Montgomery County of Maryland — This dataset includes County spending data for Montgomery County government. It does not include agency spending. Data considered sensitive or confidential and will...

High resolution hypernuclear spectroscopy at Jefferson Lab Hall A

International Nuclear Information System (INIS)

Garibaldi, F.; Bydžovský, P.; Cisbani, E.; Cusanno, F.; De Leo, R.; Frullani, S.; Iodice, M.; LeRose, J.J.; Markowitz, P.; Millener, D.J.; Urciuoli, G.M.

2013-01-01

The characteristics of the Jefferson Lab electron beam, together with those of the experimental equipment, offer a unique opportunity to study hypernuclear spectroscopy via electromagnetic induced (e,e ′ K + ) reactions. Experiment 94-107 started a systematic study on 1p-shell targets, 12 C, 9 Be and 16 O. For 12 C for the first time measurable strength in the core-excited part of the spectrum between the ground state and the p state was shown in the 12 Λ B spectrum. For 16 O a high-quality 16 Λ N spectrum was produced for the first time with sub-MeV energy resolution. A very precise Λ binding energy value for 16 Λ N, calibrated against the elementary (e,e ′ K + ) reaction on hydrogen, has also been obtained. Preliminary data on the 9 Λ Li spectrum shows some disagreement in strength for the second and third doublet with respect to the theory

Superfund fact sheet: The remedial program. Fact sheet

International Nuclear Information System (INIS)

1992-09-01

The fact sheet describes what various actions the EPA can take to clean up hazardous wastes sites. Explanations of how the criteria for environmental and public health risk assessment are determined and the role of state and local governments in site remediation are given. The fact sheet is one in a series providing reference information about Superfund issues and is intended for readers with no formal scientific training

Radiation protecting sheet

International Nuclear Information System (INIS)

Makiguchi, Hiroshi.

1989-01-01

As protection sheets used in radioactivity administration areas, a thermoplastic polyurethane composition sheet with a thickness of less 0.5 mm, solid content (ash) of less than 5% and a shore D hardness of less than 60 is used. A composite sheet with thickness of less than 0.5 mm laminated or coated with such a thermoplastic polyurethane composition as a surface layer and the thermoplastic polyurethane composition sheet applied with secondary fabrication are used. This can satisfy all of the required properties, such as draping property, abrasion resistance, high breaking strength, necking resistance, endurance strength, as well as chemical resistance and easy burnability in burning furnace. Further, by forming uneveness on the surface by means of embossing, etc. safety problems such as slippage during operation and walking can be overcome. (T.M.)

76 FR 68322 - Changes in Flood Elevation Determinations

Science.gov (United States)

2011-11-04

... 10, 2011; The Honorable David September 6, 2011 010217 of Jefferson County August 17, 2011... 420417 Haverford (11-03- 12, 2011; The Daily Wechsler, President, 0098P). Times. Township of Haverford...

Comparison of occipitocervical and atlantoaxial fusion in treatment of unstable Jefferson fractures

Directory of Open Access Journals (Sweden)

Yong Hu

2017-01-01

Full Text Available Background: Controversy exists regarding the management of unstable Jefferson fractures, with some surgeons performing reduction and immobilization of the patient in a halo vest and others performing open reduction and internal fixation. This study compares the clinical and radiological outcome parameters between posterior atlantoaxial fusion (AAF and occipitocervical fusion (OCF constructs in the treatment of the unstable atlas fracture. Materials and Methods: 68 consecutive patients with unstable Jefferson fractures treated by AAF or OCF between October 2004 and March 2011 were included in this retrospective evaluation from institutional databases. The authors reviewed medical records and original images. The patients were divided into two surgical groups treated with either AAF ( n = 48, F/M 30:18 and OCF ( n = 20, F/M 13:7 fusion. Blood loss, operative time, Japanese Orthopaedic Association (JOA score, visual analog scale (VAS score, atlanto-dens interval, lateral mass displacement, complications, and the bone fusion rates were recorded. Results: Five patients with incomplete paralysis (7.4% demonstrated postoperative improvement by more than 1 grade on the American Spinal Injury Association impairment scale. The JOA score of the AAF group improved from 12.5 ± 3.6 preoperatively to 15.7 ± 2.3 postoperatively, while the JOA score of the OCF group improved from 11.2 ± 3.3 preoperatively to 14.8 ± 4.2 postoperatively. The VAS score of AAF group decreased from 4.8 ± 1.5 preoperatively to 1.0 ± 0.4 postoperatively, the VAS score of the OCF group decreased from 5.4 ± 2.2 preoperatively to 1.3 ± 0.9 postoperatively. Conclusions: The OCF or AAF combined with short-term external immobilization can establish the upper cervical stability and prevent further spinal cord injury and nerve function damage.

Automobile sheet metal part production with incremental sheet forming

Directory of Open Access Journals (Sweden)

İsmail DURGUN

2016-02-01

Full Text Available Nowadays, effect of global warming is increasing drastically so it leads to increased interest on energy efficiency and sustainable production methods. As a result of adverse conditions, national and international project platforms, OEMs (Original Equipment Manufacturers, SMEs (Small and Mid-size Manufacturers perform many studies or improve existing methodologies in scope of advanced manufacturing techniques. In this study, advanced manufacturing and sustainable production method "Incremental Sheet Metal Forming (ISF" was used for sheet metal forming process. A vehicle fender was manufactured with or without die by using different toolpath strategies and die sets. At the end of the study, Results have been investigated under the influence of method and parameters used.Keywords: Template incremental sheet metal, Metal forming

77 FR 77082 - Changes in Flood Hazard Determinations

Science.gov (United States)

2012-12-31

.... They should not be construed to mean that the community must change any existing ordinances that are..., Commissioners, 100 Golden, CO 80419. Jefferson County Parkway, Golden, CO 80419. Florida: Broward City of...

Aspects regarding the hygienic-sanitary conditions at the level of certain dental medicine cabinets in Iasi County.

Science.gov (United States)

Cernei, E R; Maxim, Dana Cristiana; Indrei, L L

2013-01-01

This baseline study aims to find out the evaluation of hygienic-sanitary conditions at the level of dental medicine cabinets through the verification of certain hygienic aspects. The study conducted consists in monitoring the hygienic/sanitary conditions at the level of 68 dental medicine cabinets (40 private cabinets and 28 school/university dental cabinets in Iasi county), using sheets for the assessment of the hygienic/sanitary conditions adapted from the control sheets of existing dental medicine cabinets at the level of DSP (Public Health Department) Iasi. The sheets for the assessment of the hygienic/sanitary conditions were evaluated by a specialized team and the results were i llustrated in the specific charts. At the level of all the dental cabinets the study revealed nonconformities regarding the means to carry out cleaning, disinfection operations, including the management of perilous waste, the control of medical personnel. An optimization of the hygienic-sanitary conditions at the level of dental medicine cabinets is still necessary, through participation to the activity of personnel training, who is directly involved in dental medical assistance.

Geometry of thin liquid sheet flows

Science.gov (United States)

Chubb, Donald L.; Calfo, Frederick D.; Mcconley, Marc W.; Mcmaster, Matthew S.; Afjeh, Abdollah A.

1994-01-01

Incompresible, thin sheet flows have been of research interest for many years. Those studies were mainly concerned with the stability of the flow in a surrounding gas. Squire was the first to carry out a linear, invicid stability analysis of sheet flow in air and compare the results with experiment. Dombrowski and Fraser did an experimental study of the disintegration of sheet flows using several viscous liquids. They also detected the formulation of holes in their sheet flows. Hagerty and Shea carried out an inviscid stability analysis and calculated growth rates with experimental values. They compared their calculated growth rates with experimental values. Taylor studied extensively the stability of thin liquid sheets both theoretically and experimentally. He showed that thin sheets in a vacuum are stable. Brown experimentally investigated thin liquid sheet flows as a method of application of thin films. Clark and Dumbrowski carried out second-order stability analysis for invicid sheet flows. Lin introduced viscosity into the linear stability analysis of thin sheet flows in a vacuum. Mansour and Chigier conducted an experimental study of the breakup of a sheet flow surrounded by high-speed air. Lin et al. did a linear stability analysis that included viscosity and a surrounding gas. Rangel and Sirignano carried out both a linear and nonlinear invisid stability analysis that applies for any density ratio between the sheet liquid and the surrounding gas. Now there is renewed interest in sheet flows because of their possible application as low mass radiating surfaces. The objective of this study is to investigate the fluid dynamics of sheet flows that are of interest for a space radiator system. Analytical expressions that govern the sheet geometry are compared with experimental results. Since a space radiator will operate in a vacuum, the analysis does not include any drag force on the sheet flow.

Plant Operation: Work Week, Administration

Science.gov (United States)

Nation's Schools and Colleges, 1975

1975-01-01

A four-day work week for maintenance workers in the Jefferson County Public Schools in Lakewood, Colorado, reduces absenteeism and increases productivity; a basic manual for physical plant directors is reviewed. (Author/MLF)

Operating experience with superconducting cavities at Jefferson Lab

International Nuclear Information System (INIS)

Reece, C.E.

1998-01-01

The CEBAF recirculating superconducting electron linac at Jefferson Lab is now in full operation supporting nuclear physics experiments in three target halls at up to 4.4 GeV. The 330 SRF cavities, operating at 2.0 K, continue to perform well above design specifications, and have accumulated over 8,000,000 operating cavity hours. The authors have to date no evidence of degradation of cavity performance. The SRF cavities have demonstrated excellent reliability. The one klystron per cavity design provides CEBAF with flexibility and redundancy for normal operations. Several techniques have been developed for establishing optimum operating conditions for the 330 independent systems. Operation of the cavities and control systems at the full design current of 1 mA has recently been achieved. The principal constraints on usable gradient for low current operations are (1) discharge at the cold ceramic rf window induced by electron field emission in cavities, (2) tuner controls, and (3) stability of the waveguide vacuum in the region between the warm and cold windows. Several cryomodules have been improved by application of rf helium processing while installed on the beamline

Use of Light Detection and Ranging (LiDAR) to Obtain High-Resolution Elevation Data for Sussex County, Delaware

Science.gov (United States)

Barlow, Roger A.; Nardi, Mark R.; Reyes, Betzaida

2008-01-01

Sussex County, Delaware, occupies a 938-square-mile area of low relief near sea level in the Atlantic Coastal Plain. The county is bounded on the east by the Delaware Bay and the Atlantic Ocean, including a barrier-island system, and inland bays that provide habitat for valuable living resources. Eastern Sussex County is an area of rapid population growth with a long-established beach-resort community, where land elevation is a key factor in determining areas that are appropriate for development. Of concern to State and local planners are evacuation routes inland to escape flooding from severe coastal storms, as most major transportation routes traverse areas of low elevation that are subject to inundation. The western half of the county is typically rural in character, and land use is largely agricultural with some scattered forest land cover. Western Sussex County has several low-relief river flood-prone areas, where accurate high-resolution elevation data are needed for Federal Emergency Management Agency (FEMA) Digital Flood Insurance Rate Map (DFIRM) studies. This fact sheet describes the methods and techniques used to collect and process LiDAR elevation data, the generation of the digital elevation model (DEM) and the 2-foot contours, and the quality-assurance procedures and results. It indicates where to view metadata on the data sets and where to acquire bare-earth mass points, DEM data, and contour data.

A high-finesse Fabry–Perot cavity with a frequency-doubled green laser for precision Compton polarimetry at Jefferson Lab

International Nuclear Information System (INIS)

Rakhman, A.; Hafez, M.; Nanda, S.; Benmokhtar, F.; Camsonne, A.; Cates, G.D.; Dalton, M.M.; Franklin, G.B.; Friend, M.; Michaels, R.W.; Nelyubin, V.; Parno, D.S.; Paschke, K.D.; Quinn, B.P.

2016-01-01

A high-finesse Fabry–Perot cavity with a frequency-doubled continuous wave green laser (532 nm) has been built and installed in Hall A of Jefferson Lab for high precision Compton polarimetry. The infrared (1064 nm) beam from a ytterbium-doped fiber amplifier seeded by a Nd:YAG nonplanar ring oscillator laser is frequency doubled in a single-pass periodically poled MgO:LiNbO_3 crystal. The maximum achieved green power at 5 W infrared pump power is 1.74 W with a total conversion efficiency of 34.8%. The green beam is injected into the optical resonant cavity and enhanced up to 3.7 kW with a corresponding enhancement of 3800. The polarization transfer function has been measured in order to determine the intra-cavity circular laser polarization within a measurement uncertainty of 0.7%. The PREx experiment at Jefferson Lab used this system for the first time and achieved 1.0% precision in polarization measurements of an electron beam with energy and current of 1.06 GeV and 50 μA.

A high-finesse Fabry–Perot cavity with a frequency-doubled green laser for precision Compton polarimetry at Jefferson Lab

Energy Technology Data Exchange (ETDEWEB)

Rakhman, A., E-mail: rahim@ornl.gov [Syracuse University, Department of Physics, Syracuse, NY 13244 (United States); Research Accelerator Division, Spallation Neutron Source, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Hafez, M. [Old Dominion University, Applied Research Center, Norfolk, VA 23529 (United States); Nanda, S. [Thomas Jefferson National Accelerator Facility, Newport News, VA 23606 (United States); Benmokhtar, F. [Carnegie Mellon University, Department of Physics, Pittsburgh, PA 15213 (United States); Duquesne University, Pittsburgh, PA 15282 (United States); Camsonne, A. [Thomas Jefferson National Accelerator Facility, Newport News, VA 23606 (United States); Cates, G.D. [University of Virginia, Department of Physics, Charlottesville, VA 22904 (United States); Dalton, M.M. [Thomas Jefferson National Accelerator Facility, Newport News, VA 23606 (United States); University of Virginia, Department of Physics, Charlottesville, VA 22904 (United States); Franklin, G.B. [Carnegie Mellon University, Department of Physics, Pittsburgh, PA 15213 (United States); Friend, M. [Carnegie Mellon University, Department of Physics, Pittsburgh, PA 15213 (United States); High Energy Accelerator Research Organization (KEK), Tsukuba, Ibaraki (Japan); Michaels, R.W. [Thomas Jefferson National Accelerator Facility, Newport News, VA 23606 (United States); Nelyubin, V. [University of Virginia, Department of Physics, Charlottesville, VA 22904 (United States); Parno, D.S. [Carnegie Mellon University, Department of Physics, Pittsburgh, PA 15213 (United States); University of Washington, Center for Experimental Nuclear Physics and Astrophysics and Department of Physics, Seattle, WA 98195 (United States); Paschke, K.D. [University of Virginia, Department of Physics, Charlottesville, VA 22904 (United States); Quinn, B.P. [Carnegie Mellon University, Department of Physics, Pittsburgh, PA 15213 (United States); and others

2016-06-21

A high-finesse Fabry–Perot cavity with a frequency-doubled continuous wave green laser (532 nm) has been built and installed in Hall A of Jefferson Lab for high precision Compton polarimetry. The infrared (1064 nm) beam from a ytterbium-doped fiber amplifier seeded by a Nd:YAG nonplanar ring oscillator laser is frequency doubled in a single-pass periodically poled MgO:LiNbO{sub 3} crystal. The maximum achieved green power at 5 W infrared pump power is 1.74 W with a total conversion efficiency of 34.8%. The green beam is injected into the optical resonant cavity and enhanced up to 3.7 kW with a corresponding enhancement of 3800. The polarization transfer function has been measured in order to determine the intra-cavity circular laser polarization within a measurement uncertainty of 0.7%. The PREx experiment at Jefferson Lab used this system for the first time and achieved 1.0% precision in polarization measurements of an electron beam with energy and current of 1.06 GeV and 50 μA.

Best Management Practice, Fact Sheet 2. Sheet Flow to Open Space

OpenAIRE

Sample, David; Doumar, Lia

2013-01-01

This publication explains what sheet flow to open space is, where and how it is used, their limitations, routine and nonroutine maintenance, expected costs, and a glossary of terms. This fact sheet is one of a 15-part series on urban stormwater management practices.

Evolution of the Generic Lock System at Jefferson Lab

International Nuclear Information System (INIS)

Brian Bevins; Yves Roblin

2003-01-01

The Generic Lock system is a software framework that allows highly flexible feedback control of large distributed systems. It allows system operators to implement new feedback loops between arbitrary process variables quickly and with no disturbance to the underlying control system. Several different types of feedback loops are provided and more are being added. This paper describes the further evolution of the system since it was first presented at ICALEPCS 2001 and reports on two years of successful use in accelerator operations. The framework has been enhanced in several key ways. Multiple-input, multiple-output (MIMO) lock types have been added for accelerator orbit and energy stabilization. The general purpose Proportional-Integral-Derivative (PID) locks can now be tuned automatically. The generic lock server now makes use of the Proxy IOC (PIOC) developed at Jefferson Lab to allow the locks to be monitored from any EPICS Channel Access aware client. (Previously clients had to be Cdev aware.) The dependency on the Qt XML parser has been replaced with the freely available Xerces DOM parser from the Apache project

Carbon sheet pumping

International Nuclear Information System (INIS)

Ohyabu, N.; Sagara, A.; Kawamura, T.; Motojima, O.; Ono, T.

1993-07-01

A new hydrogen pumping scheme has been proposed which controls recycling of the particles for significant improvement of the energy confinement in toroidal magnetic fusion devices. In this scheme, a part of the vacuum vessel surface near the divertor is covered with carbon sheets of a large surface area. Before discharge initiation, the sheets are baked up to 700 ∼ 1000degC to remove the previously trapped hydrogen atoms. After being cooled down to below ∼ 200degC, the unsaturated carbon sheets trap high energy charge exchange hydrogen atoms effectively during a discharge and overall pumping efficiency can be as high as ∼ 50 %. (author)

FDTD modeling of thin impedance sheets

Science.gov (United States)

Luebbers, Raymond J.; Kunz, Karl S.

1991-01-01

Thin sheets of resistive or dielectric material are commonly encountered in radar cross section calculations. Analysis of such sheets is simplified by using sheet impedances. In this paper it is shown that sheet impedances can be modeled easily and accurately using Finite Difference Time Domain (FDTD) methods.

Analytical Results for 35 Mine-Waste Tailings Cores and Six Bed-Sediment Samples, and An Estimate of the Volume of Contaminated Material at Buckeye Meadow on Upper Basin Creek, Northern Jefferson County, Montana

Science.gov (United States)

Fey, David L.; Church, Stan E.; Finney, Christopher J.

1999-01-01

Metal-mining related wastes in the Boulder River basin study area in northern Jefferson County, Montana have been implicated in their detrimental effects on water quality with regard to acid-generation and toxic-metal solubilization. Flotation-mill tailings in the meadow below the Buckeye mine, hereafter referred to as the Buckeye mill-tailings site, have been identified as significant contributors to water quality degradation of Basin Creek, Montana. Basin Creek is one of three tributaries to the Boulder River in the study area; bed sediments and waters draining from the Buckeye mine have also been implicated. Geochemical analysis of 35 tailings cores and six bed-sediment samples was undertaken to determine the concentrations of Ag, As, Cd, Cu, Pb,and Zn present in these materials. These elements are environmentally significant, in that they can be toxic to fish and/or the invertebrate organisms that constitute their food. A suite of one-inch cores of dispersed flotation-mill tailings and underlying premining material was taken from a large, flat area north of Basin Creek near the site of the Buckeye mine. Thirty-five core samples were taken and divided into 204 subsamples. The samples were analyzed by ICP-AES (inductively coupled plasma-atomic emission spectroscopy) using a mixed-acid digestion. Results of the core analyses show that the elements listed above are present at moderate to very high concentrations (arsenic to 63,000 ppm, silver to 290 ppm, cadmium to 370 ppm, copper to 4,800 ppm, lead to 93,000 ppm, and zinc to 23,000 ppm). Volume calculations indicate that an estimated 8,400 metric tons of contaminated material are present at the site. Six bed-sediment samples were also subjected to the mixed-acid total digestion, and a warm (50°C) 2M HCl-1% H2O2 leach and analyzed by ICP-AES. Results indicate that bed sediments of Basin Creek are only slightly impacted by past mining above the Buckeye-Enterprise complex, moderately impacted at the upper (eastern

Upgraded photon calorimeter with integrating readout for the Hall A Compton polarimeter at Jefferson Lab

International Nuclear Information System (INIS)

Friend, M.; Parno, D.; Benmokhtar, F.; Camsonne, A.; Dalton, M.M.; Franklin, G.B.; Mamyan, V.; Michaels, R.; Nanda, S.; Nelyubin, V.; Paschke, K.; Quinn, B.; Rakhman, A.; Souder, P.; Tobias, A.

2012-01-01

The photon arm of the Compton polarimeter in Hall A of Jefferson Lab has been upgraded to allow for electron beam polarization measurements with better than 1% accuracy. The data acquisition (DAQ) system now includes an integrating mode, which eliminates several systematic uncertainties inherent in the original counting-DAQ setup. The photon calorimeter has been replaced with a Ce-doped Gd 2 SiO 5 crystal, which has a bright output and fast response, and works well for measurements using the new integrating method at electron beam energies from 1 to 6 GeV.

Edward Gantt (1742-1837): US senate chaplain and first White House physician to Thomas Jefferson.

Science.gov (United States)

Cavanagh, Harrison Dwight

2017-08-01

In his long and eventful life, Edward Gantt (1742-1837) made important contributions to the newly independent American Republic, as well as to the development of scientific evidence-based American medicine. Unfortunately, his achievements have gone unrecognized and unreported in mainstream historical publications. Specifically, his service as the first designated White House doctor, and personal physician to President Thomas Jefferson from 1801 to 1809 has not been reported. The purpose of this paper is to document the biographical and scientific details of his extraordinary life and notable contributions.

Low Level RF System for Jefferson Lab Cryomodule Test Facility

International Nuclear Information System (INIS)

Tomasz Plawski; Trent Allison; Jean Delayen; J. Hovater; Thomas Powers

2003-01-01

The Jefferson Lab Cryomodule Test Facility (CMTF) has been upgraded to test and commission SNS and CEBAF Energy Upgrade cryomodules. Part of the upgrade was to modernize the superconducting cavity instrumentation and control. We have designed a VXI based RF control system exclusively for the production testing of superconducting cavities. The RF system can be configured to work either in Phase Locked Loop (PLL) or Self Excited Loop (SEL) mode. It can be used to drive either SNS 805 MHz or CEBAF Energy Upgrade 1497 MHz superconducting cavities and can be operated in pulsed or continuous wave (CW) mode. The base design consists of RF-analog and digital sections. The RF-analog section includes a Voltage Control Oscillator (VCO), phase detector, IandQ modulator and ''low phase shift'' limiter. The digital section controls the analog section and includes ADC, FPGA, and DAC . We will discuss the design of the RF system and how it relates to the support of cavity testing

Deeply Virtual Pseudoscalar Meson Production at Jefferson Lab and Transversity GPDs

Energy Technology Data Exchange (ETDEWEB)

Kubarovsky, Valery P. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States)

2016-02-01

Transverse-momentum dependent parton distribution functions (TMDs) provide a description of nucleon structure in terms of the parton transverse momentum and its transverse spin. At leading twist there are eight TMDs, each offering a unique feature of quarks in a polarized or an unpolarized nucleon. The Sivers distribution is one of the most interesting TMD due to its non-universality. It has been extracted using the data from semi-inclusive deep-inelastic scattering (SIDIS), but there is no data yet from spin-dependent Drell-Yan (DY) process. Such measurement will provide a crucial test of TMD formalism which predicts an equal magnitude and opposite sign for the Sivers function extracted from SIDIS and DY process. We will discuss key future measurements of TMDs using both SIDIS and DY process with a focus on Hall A SoLID SIDIS program at Jefferson Lab.

New Results on Testing Duality in Spin Structure from Jefferson Lab

Energy Technology Data Exchange (ETDEWEB)

Nilanga Liyanage

2005-10-01

The Bloom-Gilman duality has been experimentally demonstrated for spin independent structure functions. Duality is observed when the smooth scaling curve at high momentum transfer is an average over the resonance bumps at lower momentum transfer, but at the same value of scaling variable x. Signs of quark-hadron duality for the spin Dependant structure function g1 of the proton has been recently reported by the Hermes collaboration. Experimental Halls A, B and C at Jefferson lab have recently measured spin structure functions in the resonance region for the proton and the neutron. Data from these experiments combined with Deep-Inelastic-Scattering data provide a precision test of quark-hadron duality predictions for spin structure functions for both the proton and the neutron. This will be one of the first precision tests of spin and flavor dependence of quark-hadron duality.

Plasma dynamics in current sheets

International Nuclear Information System (INIS)

Bogdanov, S.Yu.; Drejden, G.V.; Kirij, N.P.; AN SSSR, Leningrad

1992-01-01

Plasma dynamics in successive stages of current sheet evolution is investigated on the base of analysis of time-spatial variations of electron density and electrodynamic force fields. Current sheet formation is realized in a two-dimensional magnetic field with zero line under the action of relatively small initial disturbances (linear regimes). It is established that in the limits of the formed sheet is concentrated dense (N e ∼= 10 16 cm -3 ) (T i ≥ 100 eV, bar-Z i ≥ 2) hot pressure of which is balanced by the magnetic action of electrodynamic forces is carried out both plasma compression in the sheet limits and the acceleration along the sheet surface from a middle to narrow side edges

Specification aggregate quarry expansion: a case study demonstrating sustainable management of natural aggregate resources

Science.gov (United States)

Langer, William H.; Tucker, M.L.

2003-01-01

Many countries, provinces, territories, or states in the European Union, Australia, Canada, the United States, and elsewhere have begun implementing sustainability programs, but most of those programs stop short of sustainable management of aggregate resources. Sustainable practices do not always have to be conducted under the title of sustainability. This case study describes how Lafarge, a large multinational construction materials supplier, implemented the principles of sustainability even though there was an absence of existing local government policies or procedures addressing sustainable resource management. Jefferson County, Colorado, USA, is one of three counties in the six-county Denver, Colorado, region that has potentially available sources of crushed stone. Crushed stone comprises 30 percent of the aggregate produced in the area and plays a major role in regional aggregate resource needs. Jefferson County is home to four of the five crushed stone operations in the Denver region. Lafarge operates one of those four quarries. Lafarge recently proposed to expand its reserves by exchanging company-owned land for existing dedicated open space land adjacent to their quarry but owned by Jefferson County. A similar proposal submitted about 10 years earlier had been denied. Contrary to the earlier proposal, which was predicated on public relations, the new proposal was predicated on public trust. Although not explicitly managed under the moniker of sustainability, Lafarge used basic management principles that embody the tenets of sustainability. To achieve the goals of sustainable aggregate management where no governmental policies existed, Lafarge not only assumed their role of being a responsible corporate and environmental member of the community, but also assumed the role of facilitator to encourage and enable other stakeholders to responsibly resolve legitimate concerns regarding the Lafarge quarry proposal. Lafarge successfully presented an enlightened

46 CFR 232.4 - Balance sheet accounts.

Science.gov (United States)

2010-10-01

... 46 Shipping 8 2010-10-01 2010-10-01 false Balance sheet accounts. 232.4 Section 232.4 Shipping... ACTIVITIES UNIFORM FINANCIAL REPORTING REQUIREMENTS Balance Sheet § 232.4 Balance sheet accounts. (a.... (b) Purpose of balance sheet accounts. The balance sheet accounts are intended to disclose the...

First experimental data on the FEL - RF interaction at the Jefferson Lab IRFEL

International Nuclear Information System (INIS)

L. Merminga; P. Alexeev; S.V. Benson; A. Bolshakov; L.R. Doolittle; D.R. Douglas; C. Hovater; G.R. Neil

1999-01-01

High power FELs driven by recirculating, energy-recovering linacs can exhibit instabilities in the beam energy and laser output power. Fluctuations in the accelerating cavity fields can cause beam loss on apertures, phase oscillations and optical cavity detuning. These can affect the laser power and in turn the beam-induced voltage to further enhance the fluctuations of the rf fields. A theoretical model was developed to study the dynamics of the coupled system and was presented last year. Recently, a first set of experimental data was obtained at the Jefferson Lab IRFEL for direct comparisons with the model. The authors describe the experiment, present the data together with the modeling predictions and outline future directions

Preliminary Results from Integrating Compton Photon Polarimetry in Hall A of Jefferson Lab

International Nuclear Information System (INIS)

Parno, D; Friend, M; Benmokhtar, F; Franklin, G; Quinn, B; Michaels, R; Nanda, S; Souder, P

2011-01-01

A wide range of nucleon and nuclear structure experiments in Jefferson Lab's Hall A require precise, continuous measurements of the polarization of the electron beam. In our Compton polarimeter, electrons are scattered off photons in a Fabry-Perot cavity; by measuring an asymmetry in the integrated signal of the scattered photons detected in a GSO crystal, we can make non-invasive, continuous measurements of the beam polarization. Our goal is to achieve 1% statistical error within two hours of running. We discuss the design and commissioning of an upgrade to this apparatus, and report preliminary results for experiments conducted at beam energies from 3.5 to 5.9 GeV and photon rates from 5 to 100 kHz.

Global ice sheet modeling

International Nuclear Information System (INIS)

Hughes, T.J.; Fastook, J.L.

1994-05-01

The University of Maine conducted this study for Pacific Northwest Laboratory (PNL) as part of a global climate modeling task for site characterization of the potential nuclear waste respository site at Yucca Mountain, NV. The purpose of the study was to develop a global ice sheet dynamics model that will forecast the three-dimensional configuration of global ice sheets for specific climate change scenarios. The objective of the third (final) year of the work was to produce ice sheet data for glaciation scenarios covering the next 100,000 years. This was accomplished using both the map-plane and flowband solutions of our time-dependent, finite-element gridpoint model. The theory and equations used to develop the ice sheet models are presented. Three future scenarios were simulated by the model and results are discussed

Sheet production apparatus for removing a crystalline sheet from the surface of a melt using gas jets located above and below the crystalline sheet

Energy Technology Data Exchange (ETDEWEB)

Kellerman, Peter L.; Thronson, Gregory D.

2017-06-14

In one embodiment, a sheet production apparatus comprises a vessel configured to hold a melt of a material. A cooling plate is disposed proximate the melt and is configured to form a sheet of the material on the melt. A first gas jet is configured to direct a gas toward an edge of the vessel. A sheet of a material is translated horizontally on a surface of the melt and the sheet is removed from the melt. The first gas jet may be directed at the meniscus and may stabilize this meniscus or increase local pressure within the meniscus.

Timber resource statistics for the Olympic Peninsula, Washington.

Science.gov (United States)

Patricia M. Bassett; Daniel D. Oswald

1961-01-01

This report summarizes a 1978-79 timber resource inventory of five counties in the Olympic Peninsula of Washington: Clallam, Grays Harbor, Jefferson, Mason, and Thurston. Detailed tables of forest area, timber volume, growth, mortality, and harvest are presented.

Two Exceptional Witnesses of Latin American Independence: The Prussian Explorer Alexander Von Humboldt and The Virginian Politician Thomas Jefferson

Directory of Open Access Journals (Sweden)

Sandra Rebok

2014-01-01

Full Text Available Este artículo analiza las respectivas posturas de Alexander von Humboldt y Thomas Jefferson en relación con la independencia de los territorios hispanoamericanos y el modo en que estas se hallaban condicionadas por sus propias experiencias: Humboldt, como observador de la situación americana justo antes del comienzo de los movimientos independentistas; y Jefferson, como actor importante en la independencia de los EE.UU. y la posterior creación de una nueva sociedad. Asimismo, no se pueden estudiar sus respectivas posiciones hacia los movimientos independentistas en la América española, desvinculadas de sus conclusiones respecto a la Revolución francesa y sus consecuencias. El trabajo muestra de qué manera los dos personajes comentaron estos sucesos en la correspondencia que mantuvieron entre sí. Finalmente, también se evalúan, a través de estos famosos representantes del llamado Nuevo Mundo y el Viejo Mundo, las diferencias y similitudes en la manera de reaccionar ante estos eventos políticos y sociales desde el punto de vista europeo, en comparación con la mirada desde Norteamérica.

Vitamin and Mineral Supplement Fact Sheets

Science.gov (United States)

... website Submit Search NIH Office of Dietary Supplements Vitamin and Mineral Supplement Fact Sheets Search the list ... Supplements: Background Information Botanical Dietary Supplements: Background Information Vitamin and Mineral Fact Sheets Botanical Supplement Fact Sheets ...

Deeply virtual Compton scattering in the Hall A of Jefferson laboratory

International Nuclear Information System (INIS)

Munoz Camacho, C.

2005-12-01

Generalized Parton Distributions (GPDs), introduced in the late 90's, provide a universal description of hadrons in terms of the underlying degrees of freedom of Quantum Chromodynamics: quarks and gluons. GPDs appear in a wide variety of hard exclusive reactions and the advent of high luminosity accelerator facilities has made the study of GPDs accessible to experiment. Deeply Virtual Compton Scattering (DVCS) is the golden process involving GPDs. The first dedicated DVCS experiment ran in the Hall A of Jefferson Lab in Fall 2004. An electromagnetic calorimeter and a plastic scintillator detector were constructed for this experiment, together with specific electronics and acquisition system. The experiment preparation, data taking and analysis are described in this document. Results on the absolute cross section difference for opposite beam helicities provide the first measurement of a linear combination of GPDs as a function of the momentum transfer to the nucleon. (author)

Performance report of the U.S. Department of Energy's Jefferson Lab

International Nuclear Information System (INIS)

Jefferson Lab

1999-01-01

Jefferson Lab, the newest of the US Department of Energy's 16 national laboratories, has been functioning effectively since its inception in 1984, first during construction and later during operations. As shown in this report, JLab aligns itself directly with DOE's strategic planning, both in terms of laboratory visions and plans and in terms of actual laboratory performance. Most importantly, JLab contributes significantly to DOE's Science and Technology mission in the area of nuclear physics, under the Office of Science. The laboratory practices continuous improvement and has made a number of important effectiveness and efficiency enhancements in recent years. Laboratory performance has been demonstrated by completion of the construction phase on cost and schedule, by exceeding technical specifications when coming on-line for physics research, and then - during operations in the mid- and late- 1990's - by the application of the performance measures in the laboratory's performance-based contract with DOE

Dynamics of Radially Expanding Liquid Sheets

Science.gov (United States)

Majumdar, Nayanika; Tirumkudulu, Mahesh S.

2018-04-01

The process of atomization often involves ejecting thin liquid sheets at high speeds from a nozzle that causes the sheet to flap violently and break up into fine droplets. The flapping of the liquid sheet has long been attributed to the sheet's interaction with the surrounding gas phase. Here, we present experimental evidence to the contrary and show that the flapping is caused by the thinning of the liquid sheet as it spreads out from the nozzle exit. The measured growth rates of the waves agree remarkably well with the predictions of a recent theory that accounts for the sheet's thinning but ignores aerodynamic interactions. We anticipate these results to not only lead to more accurate predictions of the final drop-size distribution but also enable more efficient designs of atomizers.

Ground-Water System in the Chimacum Creek Basin and Surface Water/Ground Water Interaction in Chimacum and Tarboo Creeks and the Big and Little Quilcene Rivers, Eastern Jefferson County, Washington

Science.gov (United States)

Simonds, F. William; Longpre, Claire I.; Justin, Greg B.

2004-01-01

A detailed study of the ground-water system in the unconsolidated glacial deposits in the Chimacum Creek Basin and the interactions between surface water and ground water in four main drainage basins was conducted in eastern Jefferson County, Washington. The study will assist local watershed planners in assessing the status of the water resources and the potential effects of ground-water development on surface-water systems. A new surficial geologic map of the Chimacum Creek Basin and a series of hydrogeologic sections were developed by incorporating LIDAR imagery, existing map sources, and drillers' logs from 110 inventoried wells. The hydrogeologic framework outlined in the study will help characterize the occurrence of ground water in the unconsolidated glacial deposits and how it interacts with the surface-water system. Water levels measured throughout the study show that the altitude of the water table parallels the surface topography and ranges from 0 to 400 feet above the North American Vertical Datum of 1988 across the basin, and seasonal variations in precipitation due to natural cycles generally are on the order of 2 to 3 feet. Synoptic stream-discharge measurements and instream mini-piezometers and piezometers with nested temperature sensors provided additional data to refine the positions of gaining and losing reaches and delineate seasonal variations. Chimacum Creek generally gains water from the shallow ground-water system, except near the community of Chimacum where localized losses occur. In the lower portions of Chimacum Creek, gaining conditions dominate in the summer when creek stages are low and ground-water levels are high, and losing conditions dominate in the winter when creek stages are high relative to ground-water levels. In the Quilcene Bay area, three drainage basins were studied specifically to assess surface water/ground water interactions. The upper reaches of Tarboo Creek generally gain water from the shallow ground-water system

Dr. Jefferson Helm, Sr.: A Hoosier Greek Revivalist.

Science.gov (United States)

Van Meter, Lorna E.

1984-01-01

Helm was a successful physican and politician in Rush County, Indiana, during the mid-nineteenth century. He exemplified the ideals of the Greek Revival movement of the period, and he chose the architecture of that movement for his own house, a fine example of the Western Reserve style. (IS)

Buckling and stretching of thin viscous sheets

Science.gov (United States)

O'Kiely, Doireann; Breward, Chris; Griffiths, Ian; Howell, Peter; Lange, Ulrich

2016-11-01

Thin glass sheets are used in smartphone, battery and semiconductor technology, and may be manufactured by producing a relatively thick glass slab and subsequently redrawing it to a required thickness. The resulting sheets commonly possess undesired centerline ripples and thick edges. We present a mathematical model in which a viscous sheet undergoes redraw in the direction of gravity, and show that, in a sufficiently strong gravitational field, buckling is driven by compression in a region near the bottom of the sheet, and limited by viscous resistance to stretching of the sheet. We use asymptotic analysis in the thin-sheet, low-Reynolds-number limit to determine the centerline profile and growth rate of such a viscous sheet.

Ohm's law for a current sheet

Science.gov (United States)

Lyons, L. R.; Speiser, T. W.

1985-01-01

The paper derives an Ohm's law for single-particle motion in a current sheet, where the magnetic field reverses in direction across the sheet. The result is considerably different from the resistive Ohm's law often used in MHD studies of the geomagnetic tail. Single-particle analysis is extended to obtain a self-consistency relation for a current sheet which agrees with previous results. The results are applicable to the concept of reconnection in that the electric field parallel to the current is obtained for a one-dimensional current sheet with constant normal magnetic field. Dissipated energy goes directly into accelerating particles within the current sheet.

Debris flow from 2012 failure of moraine-dammed lake, Three Fingered Jack volcano, Mount Jefferson Wilderness, Oregon

Science.gov (United States)

Sherrod, David R.; Wills, Barton B.

2014-01-01

In the late spring or early summer of 2012, a flood emanated from a small moraine-dammed lake on the northeast flank of Three Fingered Jack in the Mount Jefferson Wilderness. Channel erosion or slope collapse breached the natural dam of the lake, leading to a sudden lowering of lake level by 2.8 m and discharge of 12,700 cubic meters (m3) of water. The resulting debris flow formed a bouldery deposit extending about 0.35 km downslope.

Proposed measurement of tagged deep inelastic scattering in Hall A of Jefferson lab

Energy Technology Data Exchange (ETDEWEB)

Montgomery, Rachel [Univ. of Glasgow, Scotland (United Kingdom); Annand, John [Univ. of Glasgow, Scotland (United Kingdom); Dutta, Dipangkar [Mississippi State Univ., Mississippi State, MS (United States); Keppel, Cynthia E. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); King, Paul [The Ohio State Univ., Columbus, OH (United States). Dept of Physics; Wojtsekhowski, Bogdan [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Zhang, Jixie [Univ. of Virginia, Charlottesville, VA (United States)

2017-03-01

A tagged deep inelastic scattering (TDIS) experiment is planned for Hall A of Jefferson Lab, which will probe the mesonic content of the nucleon directly. Low momentum recoiling (and spectator) protons will be measured in coincidence with electrons scattered in a deep inelastic regime from hydrogen (and deuterium) targets, covering kinematics of 8 < W2 < 18 GeV2, 1 < Q2 < 3 (GeV/c)2 and 0:05 < x < 0:2. The tagging technique will help identify scattering from partons in the meson cloud and provide access to the pion structure function via the Sullivan process. The experiment will yield the first TDIS results in the valence regime, for both proton and neutron targets. We present here an overview of the experiment.

The Jefferson Lab Quality Assurance Program for the SNS Superconducting Linac Construction Project

International Nuclear Information System (INIS)

Joseph Ozelis

2003-01-01

As part of a multi-laboratory collaboration, Jefferson Lab is currently engaged in the fabrication, assembly, and testing of 23 cryomodules for the superconducting linac portion of the Spallation Neutron Source (SNS) being built at Oak Ridge National Laboratory. As with any large accelerator construction project, it is vitally important that these components be built in a cost effective and timely manner, and that they meet the stringent performance requirements dictated by the project specifications. A comprehensive Quality Assurance (QA) program designed to help accomplish these goals has been implemented as an inherent component of JLab's SNS construction effort. This QA program encompasses the traditional spectrum of component performance, from incoming parts inspection, raw materials testing, through to sub-assembly and finished article performance evaluation

Electroproduction of neutral pions in the Hall A at the Jefferson Laboratory; Electroproduction de pions neutres dans le Hall A au Jefferson Laboratory

Energy Technology Data Exchange (ETDEWEB)

Fuchey, Eric [Blaise Pascal Univ., Aubiere (France)

2010-06-01

The past decade has seen a strong evolution of the study of the hadron structure through exclusive processes, allowing to access to a more complete description of this structure. Exclusive processes include DVCS (Deeply Virtual Compton Scattering) as well as hard exclusive meson production. This document is particularly focussed on the latter, and more particularly on exclusive neutral pion production. In this thesis is described the analysis of triple coincidence events H(e, e'γγ)X, which were a consequent by-product of the DVCS experiment which occured during Fall 2004 at Jefferson Lab Hall A, to extract the ep → epπ⁰ cross section. This cross section has been measured at two values of four-momentum transfer Q² = 1.9 GeV² and Q² = 2.3 GeV². The statistical precision for these measurements is achieved at better than 5 %. The kinematic range allows to study the evolution of the extracted cross section as a function of Q² and W. Results are be confronted with Regge inspired calculations and Generalized (GPD) predictions. An intepretation of our

Adjustable focus laser sheet module for generating constant maximum width sheets for use in optical flow diagnostics

International Nuclear Information System (INIS)

Hult, J; Mayer, S

2011-01-01

A general design of a laser light sheet module with adjustable focus is presented, where the maximum sheet width is preserved over a fixed region. In contrast, conventional focusing designs are associated with a variation in maximum sheet width with focal position. A four lens design is proposed here, where the first three lenses are employed for focusing, and the last for sheet expansion. A maximum sheet width of 1100 µm was maintained over a 50 mm long distance, for focal distances ranging from 75 to 500 mm, when a 532 nm laser beam with a beam quality factor M 2 = 29 was used for illumination

Collisionless current sheet equilibria

Science.gov (United States)

Neukirch, T.; Wilson, F.; Allanson, O.

2018-01-01

Current sheets are important for the structure and dynamics of many plasma systems. In space and astrophysical plasmas they play a crucial role in activity processes, for example by facilitating the release of magnetic energy via processes such as magnetic reconnection. In this contribution we will focus on collisionless plasma systems. A sensible first step in any investigation of physical processes involving current sheets is to find appropriate equilibrium solutions. The theory of collisionless plasma equilibria is well established, but over the past few years there has been a renewed interest in finding equilibrium distribution functions for collisionless current sheets with particular properties, for example for cases where the current density is parallel to the magnetic field (force-free current sheets). This interest is due to a combination of scientific curiosity and potential applications to space and astrophysical plasmas. In this paper we will give an overview of some of the recent developments, discuss their potential applications and address a number of open questions.

Thomas Jefferson, I dilemmi della democrazia americana, translated and edited by Alberto Giordano, with a preface by Dino Cofrancesco (Novi Ligure: Città del Silenzio, 2007

Directory of Open Access Journals (Sweden)

Pierluigi Chiassoni

2010-03-01

Full Text Available A review of Thomas Jefferson, I dilemmi della democrazia americana, translated and edited by Alberto Giordano, with a preface by Dino Cofrancesco (Novi Ligure: Città del Silenzio, 2007

17 CFR 210.6-04 - Balance sheets.

Science.gov (United States)

2010-04-01

... 17 Commodity and Securities Exchanges 2 2010-04-01 2010-04-01 false Balance sheets. 210.6-04... sheets. This rule is applicable to balance sheets filed by registered investment companies except for... of this part. Balance sheets filed under this rule shall comply with the following provisions: Assets...

Ice sheet in peril

DEFF Research Database (Denmark)

Hvidberg, Christine Schøtt

2016-01-01

Earth's large ice sheets in Greenland and Antarctica are major contributors to sea level change. At present, the Greenland Ice Sheet (see the photo) is losing mass in response to climate warming in Greenland (1), but the present changes also include a long-term response to past climate transitions...

The transposition of the balance sheet to financial and functional balance sheet. Research and development

Directory of Open Access Journals (Sweden)

Liana GĂDĂU

2015-09-01

Full Text Available As the title suggests, through this paper we want to highlight the necessity of treating again the content and the form of the balance sheet in order to adapt it to a more efficient analysis, this way surpassing the informational valences of the classic balance sheet. The functional and the financial balance sheet will be taken into account. These models of balance sheet permit the complex analyses regarding the solvability or the bankruptcy risk of an enterprise to take place, and also other analyses, like the analysis of the structure and the financial/ functional equilibrium, the analysis of the company on operating cycles and their role in the functioning of the company. Through the particularities offered by each of these two models of balance sheet, we want to present the advantages of a superior informing. This content of this material is based on a vast investigation of the specialized literature.

Ice_Sheets_CCI: Essential Climate Variables for the Greenland Ice Sheet

Science.gov (United States)

Forsberg, R.; Sørensen, L. S.; Khan, A.; Aas, C.; Evansberget, D.; Adalsteinsdottir, G.; Mottram, R.; Andersen, S. B.; Ahlstrøm, A.; Dall, J.; Kusk, A.; Merryman, J.; Hvidberg, C.; Khvorostovsky, K.; Nagler, T.; Rott, H.; Scharrer, M.; Shepard, A.; Ticconi, F.; Engdahl, M.

2012-04-01

As part of the ESA Climate Change Initiative (www.esa-cci.org) a long-term project "ice_sheets_cci" started January 1, 2012, in addition to the existing 11 projects already generating Essential Climate Variables (ECV) for the Global Climate Observing System (GCOS). The "ice_sheets_cci" goal is to generate a consistent, long-term and timely set of key climate parameters for the Greenland ice sheet, to maximize the impact of European satellite data on climate research, from missions such as ERS, Envisat and the future Sentinel satellites. The climate parameters to be provided, at first in a research context, and in the longer perspective by a routine production system, would be grids of Greenland ice sheet elevation changes from radar altimetry, ice velocity from repeat-pass SAR data, as well as time series of marine-terminating glacier calving front locations and grounding lines for floating-front glaciers. The ice_sheets_cci project will involve a broad interaction of the relevant cryosphere and climate communities, first through user consultations and specifications, and later in 2012 optional participation in "best" algorithm selection activities, where prototype climate parameter variables for selected regions and time frames will be produced and validated using an objective set of criteria ("Round-Robin intercomparison"). This comparative algorithm selection activity will be completely open, and we invite all interested scientific groups with relevant experience to participate. The results of the "Round Robin" exercise will form the algorithmic basis for the future ECV production system. First prototype results will be generated and validated by early 2014. The poster will show the planned outline of the project and some early prototype results.

AI applications in sheet metal forming

CERN Document Server

Hussein, Hussein

2017-01-01

This book comprises chapters on research work done around the globe in the area of artificial intelligence (AI) applications in sheet metal forming. The first chapter offers an introduction to various AI techniques and sheet metal forming, while subsequent chapters describe traditional procedures/methods used in various sheet metal forming processes, and focus on the automation of those processes by means of AI techniques, such as KBS, ANN, GA, CBR, etc. Feature recognition and the manufacturability assessment of sheet metal parts, process planning, strip-layout design, selecting the type and size of die components, die modeling, and predicting die life are some of the most important aspects of sheet metal work. Traditionally, these activities are highly experience-based, tedious and time consuming. In response, researchers in several countries have applied various AI techniques to automate these activities, which are covered in this book. This book will be useful for engineers working in sheet metal industri...

Neutron Arm Study and Calibration for the GEn Experiment at Thomas Jefferson National Laboratory

International Nuclear Information System (INIS)

Timothy Ngo

2007-01-01

The measurement of the neutron electric form factor, GEn, will allow us to solve indirectly for the quark charge distribution inside of the neutron. With the equipment at Jefferson Lab we have measured GEn at four momentum transfer values of Q**2 at 1.3, 2.4 and 3.4 (GeV/c)**2 using a polarized electron beam and polarized Helium target. The scattered electrons off of the Helium target are detected in the BigBite spectrometer and the recoiling neutrons from the Helium are detected in the Neutron Arm, which is composed of an array of scintillators. The main focus of this thesis will be devoted to the geometry, timing and energy calibrations of the Neutron Arm

Effect of Temperature and Sheet Temper on Isothermal Solidification Kinetics in Clad Aluminum Brazing Sheet

Science.gov (United States)

Benoit, Michael J.; Whitney, Mark A.; Wells, Mary A.; Winkler, Sooky

2016-09-01

Isothermal solidification (IS) is a phenomenon observed in clad aluminum brazing sheets, wherein the amount of liquid clad metal is reduced by penetration of the liquid clad into the core. The objective of the current investigation is to quantify the rate of IS through the use of a previously derived parameter, the Interface Rate Constant (IRC). The effect of peak temperature and initial sheet temper on IS kinetics were investigated. The results demonstrated that IS is due to the diffusion of silicon (Si) from the liquid clad layer into the solid core. Reduced amounts of liquid clad at long liquid duration times, a roughened sheet surface, and differences in resolidified clad layer morphology between sheet tempers were observed. Increased IS kinetics were predicted at higher temperatures by an IRC model as well as by experimentally determined IRC values; however, the magnitudes of these values are not in good agreement due to deficiencies in the model when applied to alloys. IS kinetics were found to be higher for sheets in the fully annealed condition when compared with work-hardened sheets, due to the influence of core grain boundaries providing high diffusivity pathways for Si diffusion, resulting in more rapid liquid clad penetration.

Dutchess County Resource Recovery Task Force report: Dutchess County Pyrolysis Program

Energy Technology Data Exchange (ETDEWEB)

None

1980-07-01

Dutchess County initiated development of a long-range master plan for Solid Waste Management in 1971. The plan included development of a resource recovery facility to service the municipalities in the County population center. Based on early recommendations, a pyrolysis facility employing Purox technology was to be implemented. A feasibility study, paid for by County funds was completed in 1975. The study provided siting recommendations, estimation of available waste, and preliminary facility design. Because of various considerations, the project was not developed. Under the Department of Energy grant, the County reassessed the feasibility of a resource recovery facility, with emphasis on confirming previous conclusions supporting the Purox technology, waste availability, energy recovery and sale and siting of the plant. The conclusions reached in the new study were: a resource recovery facility is feasible for the County; sufficient waste for such a facility is available and subject to control; While Purox technology was feasible it is not the most appropriate available technoloy for the County; that mass burning with steam recovery is the most appropriate technology; and that resource recovery while presently more expensive than landfilling, represents the only cost effective, energy efficient, and environmentally sound way to handle the solid waste problem in the County.

Energy information sheets

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-01

The National Energy Information Center (NEIC), as part of its mission, provides energy information and referral assistance to Federal, State, and local governments, the academic community, business and industrial organizations, and the public. The Energy Information Sheets was developed to provide general information on various aspects of fuel production, prices, consumption, and capability. Additional information on related subject matter can be found in other Energy Information Administration (EIA) publications as referenced at the end of each sheet.

Experiments on sheet metal shearing

OpenAIRE

Gustafsson, Emil

2013-01-01

Within the sheet metal industry, different shear cutting technologies are commonly used in several processing steps, e.g. in cut to length lines, slitting lines, end cropping etc. Shearing has speed and cost advantages over competing cutting methods like laser and plasma cutting, but involves large forces on the equipment and large strains in the sheet material.Numerical models to predict forces and sheared edge geometry for different sheet metal grades and different shear parameter set-ups a...

Genetic and Environmental Contributions to Behavioral Stability and Change in Children 6-36 months of Age Using Louisville Twin Study Data.

Science.gov (United States)

Davis, Deborah Winders; Finkel, Deborah; Turkheimer, Eric; Dickens, William

2015-11-01

The Infant Behavior Record (IBR) from the Bayley Scales of Infant Development has been used to study behavioral development since the 1960s. Matheny (1983) examined behavioral development at 6, 12, 18, and 24 months from the Louisville Twin Study (LTS). The extracted temperament scales included Task Orientation, Affect-Extraversion, and Activity. He concluded that monozygotic twins were more similar than same-sex dizygotic twins on these dimensions. Since this seminal work was published, a larger LTS sample and more advanced analytical methods are available. In the current analyses, Choleksy decomposition was applied to behavioral data (n = 1231) from twins 6-36 months. Different patterns of genetic continuity vs genetic innovations were identified for each IBR scale. Single common genetic and shared environmental factors explained cross-age twin similarity in the Activity scale. Multiple shared environmental factors and a single genetic factor coming on line at age 18 months contributed to Affect-Extraversion. A single shared environmental factor and multiple genetic factors explained cross-age twin similarity in Task Orientation.

Economic Impacts and Business Opportunities | NREL

Science.gov (United States)

Economic Impacts and Business Opportunities Economic Impacts and Business Opportunities NREL corporations alike. Colorado flag Economic Impact The economic impact of NREL operations on the nation totaled Jefferson County where the economic benefit totaled $275 million in 2014. Growth chart Economic Benefit NREL

78 FR 9418 - National Register of Historic Places; Notification of Pending Nominations and Related Actions

Science.gov (United States)

2013-02-08

... County Rock Hill Printing and Finishing Company, 400 W. White St., Rock Hill, 12001264 VIRGINIA Augusta... Ellen Henderson, House, 307 S. Maple Ave., Falls Church (Independent City), 12001267 Franklin..., 1739 Jefferson Davis Hwy., Stafford, 12001272 Virginia Beach Independent City Green Hill, 1721 Lovetts...

Predicting Pulsar Scintillation from Refractive Plasma Sheets

Science.gov (United States)

Simard, Dana; Pen, Ue-Li

2018-05-01

The dynamic and secondary spectra of many pulsars show evidence for long-lived, aligned images of the pulsar that are stationary on a thin scattering sheet. One explanation for this phenomenon considers the effects of wave crests along sheets in the ionized interstellar medium, such as those due to Alfvén waves propagating along current sheets. If these sheets are closely aligned to our line-of-sight to the pulsar, high bending angles arise at the wave crests and a selection effect causes alignment of images produced at different crests, similar to grazing reflection off of a lake. Using geometric optics, we develop a simple parameterized model of these corrugated sheets that can be constrained with a single observation and that makes observable predictions for variations in the scintillation of the pulsar over time and frequency. This model reveals qualitative differences between lensing from overdense and underdense corrugated sheets: Only if the sheet is overdense compared to the surrounding interstellar medium can the lensed images be brighter than the line-of-sight image to the pulsar, and the faint lensed images are closer to the pulsar at higher frequencies if the sheet is underdense, but at lower frequencies if the sheet is overdense.

Energized Oxygen : Speiser Current Sheet Bifurcation

Science.gov (United States)

George, D. E.; Jahn, J. M.

2017-12-01

A single population of energized Oxygen (O+) is shown to produce a cross-tail bifurcated current sheet in 2.5D PIC simulations of the magnetotail without the influence of magnetic reconnection. Treatment of oxygen in simulations of space plasmas, specifically a magnetotail current sheet, has been limited to thermal energies despite observations of and mechanisms which explain energized ions. We performed simulations of a homogeneous oxygen background, that has been energized in a physically appropriate manner, to study the behavior of current sheets and magnetic reconnection, specifically their bifurcation. This work uses a 2.5D explicit Particle-In-a-Cell (PIC) code to investigate the dynamics of energized heavy ions as they stream Dawn-to-Dusk in the magnetotail current sheet. We present a simulation study dealing with the response of a current sheet system to energized oxygen ions. We establish a, well known and studied, 2-species GEM Challenge Harris current sheet as a starting point. This system is known to eventually evolve and produce magnetic reconnection upon thinning of the current sheet. We added a uniform distribution of thermal O+ to the background. This 3-species system is also known to eventually evolve and produce magnetic reconnection. We add one additional variable to the system by providing an initial duskward velocity to energize the O+. We also traced individual particle motion within the PIC simulation. Three main results are shown. First, energized dawn- dusk streaming ions are clearly seen to exhibit sustained Speiser motion. Second, a single population of heavy ions clearly produces a stable bifurcated current sheet. Third, magnetic reconnection is not required to produce the bifurcated current sheet. Finally a bifurcated current sheet is compatible with the Harris current sheet model. This work is the first step in a series of investigations aimed at studying the effects of energized heavy ions on magnetic reconnection. This work differs

Experimental formability analysis of bondal sandwich sheet

Science.gov (United States)

Kami, Abdolvahed; Banabic, Dorel

2018-05-01

Metal/polymer/metal sandwich sheets have recently attracted the interests of industries like automotive industry. These sandwich sheets have superior properties over single-layer metallic sheets including good sound and vibration damping and light weight. However, the formability of these sandwich sheets should be enhanced which requires more research. In this paper, the formability of Bondal sheet (DC06/viscoelastic polymer/DC06 sandwich sheet) was studied through different types of experiments. The mechanical properties of Bondal were determined by uniaxial tensile tests. Hemispherical punch stretching and hydraulic bulge tests were carried out to determine the forming limit diagram (FLD) of Bondal. Furthermore, cylindrical and square cup drawing tests were performed in dry and oil lubricated conditions. These tests were conducted at different blank holding forces (BHFs). An interesting observation about Bondal sheet deep drawing was obtaining of higher drawing depths at dry condition in comparison with oil-lubricated condition.

Orthoimagery Submission for Jefferson County, WI, USA - MIP Jefferson Portion Rock River RiskMap DFIRM Update

Data.gov (United States)

Federal Emergency Management Agency, Department of Homeland Security — Digital orthographic imagery datasets contain georeferenced images of the Earth's surface, collected by a sensor in which object displacement has been removed for...

Depleted uranium risk assessment for Jefferson Proving Ground using data from environmental monitoring and site characterization. Final report

International Nuclear Information System (INIS)

Ebinger, M.H.; Hansen, W.R.

1996-10-01

This report documents the third risk assessment completed for the depleted uranium (DU) munitions testing range at Jefferson Proving Ground (JPG), Indiana, for the U.S. Army Test and Evaluation command. Jefferson Proving Ground was closed in 1995 under the Base Realignment and Closure Act and the testing mission was moved to Yuma Proving Ground. As part of the closure of JPG, assessments of potential adverse health effects to humans and the ecosystem were conducted. This report integrates recent information obtained from site characterization surveys at JPG with environmental monitoring data collected from 1983 through 1994 during DU testing. Three exposure scenarios were evaluated for potential adverse effects to human health: an occasional use scenario and two farming scenarios. Human exposure was minimal from occasional use, but significant risk were predicted from the farming scenarios when contaminated groundwater was used by site occupants. The human health risk assessments do not consider the significant risk posed by accidents with unexploded ordnance. Exposures of white-tailed deer to DU were also estimated in this study, and exposure rates result in no significant increase in either toxicological or radiological risks. The results of this study indicate that remediation of the DU impact area would not substantially reduce already low risks to humans and the ecosystem, and that managed access to JPG is a reasonable model for future land use options

Ice sheet hydrology - a review

International Nuclear Information System (INIS)

Jansson, Peter; Naeslund, Jens-Ove; Rodhe, Lars

2007-03-01

This report summarizes the theoretical knowledge on water flow in and beneath glaciers and ice sheets and how these theories are applied in models to simulate the hydrology of ice sheets. The purpose is to present the state of knowledge and, perhaps more importantly, identify the gaps in our understanding of ice sheet hydrology. Many general concepts in hydrology and hydraulics are applicable to water flow in glaciers. However, the unique situation of having the liquid phase flowing in conduits of the solid phase of the same material, water, is not a commonly occurring phenomena. This situation means that the heat exchange between the phases and the resulting phase changes also have to be accounted for in the analysis. The fact that the solidus in the pressure-temperature dependent phase diagram of water has a negative slope provides further complications. Ice can thus melt or freeze from both temperature and pressure variations or variations in both. In order to provide details of the current understanding of water flow in conjunction with deforming ice and to provide understanding for the development of ideas and models, emphasis has been put on the mathematical treatments, which are reproduced in detail. Qualitative results corroborating theory or, perhaps more often, questioning the simplifications made in theory, are also given. The overarching problem with our knowledge of glacier hydrology is the gap between the local theories of processes and the general flow of water in glaciers and ice sheets. Water is often channelized in non-stationary conduits through the ice, features which due to their minute size relative to the size of glaciers and ice sheets are difficult to incorporate in spatially larger models. Since the dynamic response of ice sheets to global warming is becoming a key issue in, e.g. sea-level change studies, the problems of the coupling between the hydrology of an ice sheet and its dynamics is steadily gaining interest. New work is emerging

Ice sheet hydrology - a review

Energy Technology Data Exchange (ETDEWEB)

Jansson, Peter; Naeslund, Jens-Ove [Dept. of Physical Geography and Quaternary Geology, Stockholm Univ., Stockholm (Sweden); Rodhe, Lars [Geological Survey of Sweden, Uppsala (Sweden)

2007-03-15

This report summarizes the theoretical knowledge on water flow in and beneath glaciers and ice sheets and how these theories are applied in models to simulate the hydrology of ice sheets. The purpose is to present the state of knowledge and, perhaps more importantly, identify the gaps in our understanding of ice sheet hydrology. Many general concepts in hydrology and hydraulics are applicable to water flow in glaciers. However, the unique situation of having the liquid phase flowing in conduits of the solid phase of the same material, water, is not a commonly occurring phenomena. This situation means that the heat exchange between the phases and the resulting phase changes also have to be accounted for in the analysis. The fact that the solidus in the pressure-temperature dependent phase diagram of water has a negative slope provides further complications. Ice can thus melt or freeze from both temperature and pressure variations or variations in both. In order to provide details of the current understanding of water flow in conjunction with deforming ice and to provide understanding for the development of ideas and models, emphasis has been put on the mathematical treatments, which are reproduced in detail. Qualitative results corroborating theory or, perhaps more often, questioning the simplifications made in theory, are also given. The overarching problem with our knowledge of glacier hydrology is the gap between the local theories of processes and the general flow of water in glaciers and ice sheets. Water is often channelized in non-stationary conduits through the ice, features which due to their minute size relative to the size of glaciers and ice sheets are difficult to incorporate in spatially larger models. Since the dynamic response of ice sheets to global warming is becoming a key issue in, e.g. sea-level change studies, the problems of the coupling between the hydrology of an ice sheet and its dynamics is steadily gaining interest. New work is emerging

DCS Survey Submission for Various Streams in Jefferson County

Data.gov (United States)

Federal Emergency Management Agency, Department of Homeland Security — Survey data includes spatial datasets and data tables necessary to digitally represent data collected in the survey phase of the study. (Source: FEMA Guidelines and...

DIGITAL FLOOD INSURANCE RATE MAP DATABASE, Jefferson COUNTY, AL

Data.gov (United States)

Federal Emergency Management Agency, Department of Homeland Security — The Digital Flood Insurance Rate Map (DFIRM) Database depicts flood risk information and supporting data used to develop the risk data. The primary risk...

Allegheny County Addressing Landmarks

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — This dataset contains address points which represent physical address locations assigned by the Allegheny County addressing authority. Data is updated by County...

Allegheny County Address Points

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — This dataset contains address points which represent physical address locations assigned by the Allegheny County addressing authority. Data is updated by County...

Disintegration of liquid sheets

Science.gov (United States)

Mansour, Adel; Chigier, Norman

1990-01-01

The development, stability, and disintegration of liquid sheets issuing from a two-dimensional air-assisted nozzle is studied. Detailed measurements of mean drop size and velocity are made using a phase Doppler particle analyzer. Without air flow the liquid sheet converges toward the axis as a result of surface tension forces. With airflow a quasi-two-dimensional expanding spray is formed. The air flow causes small variations in sheet thickness to develop into major disturbances with the result that disruption starts before the formation of the main break-up region. In the two-dimensional variable geometry air-blast atomizer, it is shown that the air flow is responsible for the formation of large, ordered, and small chaotic 'cell' structures.

Root-growth-inhibiting sheet

Science.gov (United States)

Burton, F.G.; Cataldo, D.A.; Cline, J.F.; Skiens, W.E.; Van Voris, P.

1993-01-26

In accordance with this invention, a porous sheet material is provided at intervals with bodies of a polymer which contain a 2,6-dinitroaniline. The sheet material is made porous to permit free passage of water. It may be either a perforated sheet or a woven or non-woven textile material. A particularly desirable embodiment is a non-woven fabric of non-biodegradable material. This type of material is known as a geotextile'' and is used for weed control, prevention of erosion on slopes, and other landscaping purposes. In order to obtain a root repelling property, a dinitroaniline is blended with a polymer which is attached to the geotextile or other porous material.

Root-growth-inhibiting sheet

Science.gov (United States)

Burton, Frederick G.; Cataldo, Dominic A.; Cline, John F.; Skiens, W. Eugene; Van Voris, Peter

1993-01-01

In accordance with this invention, a porous sheet material is provided at intervals with bodies of a polymer which contain a 2,6-dinitroaniline. The sheet material is made porous to permit free passage of water. It may be either a perforated sheet or a woven or non-woven textile material. A particularly desirable embodiment is a non-woven fabric of non-biodegradable material. This type of material is known as a "geotextile" and is used for weed control, prevention of erosion on slopes, and other landscaping purposes. In order to obtain a root repelling property, a dinitroaniline is blended with a polymer which is attached to the geotextile or other porous material.

Radiation therapy for pineal tumors: 30-year experience at Thomas Jefferson University Hospital

International Nuclear Information System (INIS)

Dickerson, G.A.; Tupchong, L.; Moylan, D.J.; Kramer, S.

1987-01-01

Eighteen tumors of the pineal region were treated at Thomas Jefferson University Hospital since 1957. Preoperative evaluation included CT scan in 11 patients and cerebrospinal fluid cytology in four. Histologic diagnosis was obtained in nine patients. Diagnosis in two other patients was based on CT scan response at 2,000 cGY. Fifteen patients received whole-brain irradiation with a boost, one each with limited-field and whole-brain irradiation only. One patient with melanoma received craniospinal irradiation. Median pineal dose was 55 Gy; range, 50-60 Gy. Five treatment failures occurred, four local and one distant. Actuarial survival was 80%, 70%, and 65% at 5, 10, and 20 years. Median follow-up was 8.8 years. Cranial radiotherapy alone appears to control the majority of pineal tumors

Allegheny County Air Quality

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — Air quality data from Allegheny County Health Department monitors throughout the county. Air quality monitored data must be verified by qualified individuals before...

Mobility Balance Sheet 2009

International Nuclear Information System (INIS)

Jorritsma, P.; Derriks, H.; Francke, J.; Gordijn, H.; Groot, W.; Harms, L.; Van der Loop, H.; Peer, S.; Savelberg, F.; Wouters, P.

2009-06-01

The Mobility Balance Sheet provides an overview of the state of the art of mobility in the Netherlands. In addition to describing the development of mobility this report also provides explanations for the growth of passenger and freight transport. Moreover, the Mobility Balance Sheet also focuses on a topical theme: the effects of economic crises on mobility. [nl

Allegheny County Municipal Boundaries

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — This dataset demarcates the municipal boundaries in Allegheny County. Data was created to portray the boundaries of the 130 Municipalities in Allegheny County the...

Safety advice sheets

CERN Multimedia

HSE Unit

2013-01-01

You never know when you might be faced with questions such as: when/how should I dispose of a gas canister? Where can I find an inspection report? How should I handle/store/dispose of a chemical substance…?   The SI section of the DGS/SEE Group is primarily responsible for safety inspections, evaluating the safety conditions of equipment items, premises and facilities. On top of this core task, it also regularly issues “Safety Advice Sheets” on various topics, designed to be of assistance to users but also to recall and reinforce safety rules and procedures. These clear and concise sheets, complete with illustrations, are easy to display in the appropriate areas. The following safety advice sheets have been issued so far: Other sheets will be published shortly. Suggestions are welcome and should be sent to the SI section of the DGS/SEE Group. Please send enquiries to general-safety-visits.service@cern.ch.

Manifold free multiple sheet superplastic forming

Science.gov (United States)

Elmer, John W.; Bridges, Robert L.

2004-01-13

Fluid-forming compositions in a container attached to enclosed adjacent sheets are heated to relatively high temperatures to generate fluids (gases) that effect inflation of the sheets. Fluid rates to the enclosed space between the sheets can be regulated by the canal from the container. Inflated articles can be produced by a continuous, rather than batch-type, process.

21 CFR 880.5180 - Burn sheet.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Burn sheet. 880.5180 Section 880.5180 Food and... Burn sheet. (a) Identification. A burn sheet is a device made of a porous material that is wrapped aroung a burn victim to retain body heat, to absorb wound exudate, and to serve as a barrier against...

Sheet-bulk metal forming – forming of functional components from sheet metals

Directory of Open Access Journals (Sweden)

Merklein Marion

2015-01-01

Full Text Available The paper gives an overview on the application of sheet-bulk metal forming operations in both scientific and industrial environment. Beginning with the need for an innovative forming technology, the definition of this new process class is introduced. The rising challenges of the application of bulk metal forming operations on sheet metals are presented and the demand on a holistic investigation of this topic is motivated. With the help of examples from established production processes, the latest state of technology and the lack on fundamental knowledge is shown. Furthermore, perspectives regarding new research topics within sheet-bulk metal forming are presented. These focus on processing strategies to improve the quality of functional components by the application of process-adapted semi-finished products as well as the local adaption of the tribological system.

Reconstructing the last Irish Ice Sheet 2: a geomorphologically-driven model of ice sheet growth, retreat and dynamics

Science.gov (United States)

Greenwood, Sarah L.; Clark, Chris D.

2009-12-01

The ice sheet that once covered Ireland has a long history of investigation. Much prior work focussed on localised evidence-based reconstructions and ice-marginal dynamics and chronologies, with less attention paid to an ice sheet wide view of the first order properties of the ice sheet: centres of mass, ice divide structure, ice flow geometry and behaviour and changes thereof. In this paper we focus on the latter aspect and use our new, countrywide glacial geomorphological mapping of the Irish landscape (>39 000 landforms), and our analysis of the palaeo-glaciological significance of observed landform assemblages (article Part 1), to build an ice sheet reconstruction yielding these fundamental ice sheet properties. We present a seven stage model of ice sheet evolution, from initiation to demise, in the form of palaeo-geographic maps. An early incursion of ice from Scotland likely coalesced with local ice caps and spread in a south-westerly direction 200 km across Ireland. A semi-independent Irish Ice Sheet was then established during ice sheet growth, with a branching ice divide structure whose main axis migrated up to 140 km from the west coast towards the east. Ice stream systems converging on Donegal Bay in the west and funnelling through the North Channel and Irish Sea Basin in the east emerge as major flow components of the maximum stages of glaciation. Ice cover is reconstructed as extending to the continental shelf break. The Irish Ice Sheet became autonomous (i.e. separate from the British Ice Sheet) during deglaciation and fragmented into multiple ice masses, each decaying towards the west. Final sites of demise were likely over the mountains of Donegal, Leitrim and Connemara. Patterns of growth and decay of the ice sheet are shown to be radically different: asynchronous and asymmetric in both spatial and temporal domains. We implicate collapse of the ice stream system in the North Channel - Irish Sea Basin in driving such asymmetry, since rapid

Pre-LGM Northern Hemisphere ice sheet topography

Directory of Open Access Journals (Sweden)

J. Kleman

2013-10-01

Full Text Available We here reconstruct the paleotopography of Northern Hemisphere ice sheets during the glacial maxima of marine isotope stages (MIS 5b and 4.We employ a combined approach, blending geologically based reconstruction and numerical modeling, to arrive at probable ice sheet extents and topographies for each of these two time slices. For a physically based 3-D calculation based on geologically derived 2-D constraints, we use the University of Maine Ice Sheet Model (UMISM to calculate ice sheet thickness and topography. The approach and ice sheet modeling strategy is designed to provide robust data sets of sufficient resolution for atmospheric circulation experiments for these previously elusive time periods. Two tunable parameters, a temperature scaling function applied to a spliced Vostok–GRIP record, and spatial adjustment of the climatic pole position, were employed iteratively to achieve a good fit to geological constraints where such were available. The model credibly reproduces the first-order pattern of size and location of geologically indicated ice sheets during marine isotope stages (MIS 5b (86.2 kyr model age and 4 (64 kyr model age. From the interglacial state of two north–south obstacles to atmospheric circulation (Rocky Mountains and Greenland, by MIS 5b the emergence of combined Quebec–central Arctic and Scandinavian–Barents-Kara ice sheets had increased the number of such highland obstacles to four. The number of major ice sheets remained constant through MIS 4, but the merging of the Cordilleran and the proto-Laurentide Ice Sheet produced a single continent-wide North American ice sheet at the LGM.

Allegheny County Council Districts

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — This dataset portrays the boundaries of the County Council Districts in Allegheny County. The dataset is based on municipal boundaries and City of Pittsburgh ward...

Optical modeling of the Jefferson Lab IR Demo FEL

International Nuclear Information System (INIS)

Neil, G.; Benson, S.; Shinn, M.; Davidson, P.; Kloppel, P.

1997-01-01

The Thomas Jefferson National Accelerator Facility (formerly known as CEBAF) has embarked on the construction of a 1 kW free-electron laser operating initially at 3 microns that is designed for laser-material interaction experiments and to explore the feasibility of scaling the system in power and wavelength for industrial and Navy defense applications. The superconducting radio-frequency linac, and single-pass transport which accelerates the beam from injector to wiggler, followed by energy-recovery deceleration to a dump. The electron and optical beam time structure in the design consists of a train of pecosecond pulses at a 37.425 MHz pulse repetition rate. The initial optical configuration is a conventional near-concentric resonator with transmissive outcoupling. Future upgrades of the system will increase the power and shorten the operating wavelength, and utilize a more advanced resonator system capable of scaling to high powers. The optical system of the laser has been mode led using the GLAD code by using a Beer's-law region to mimic the FEL interaction. Effects such as mirror heating have been calculated and compared with analytical treatments. The magnitude of the distorium for several materials and wavelengths has been estimated. The advantages as well as the limitations of this approach are discussed

Infection prevention and control and the refugee population: Experiences from the University of Louisville Global Health Center.

Science.gov (United States)

Carrico, Ruth M; Goss, Linda; Wiemken, Timothy L; Bosson, Rahel S; Peyrani, Paula; Mattingly, William A; Pauly, Allison; Ford, Rebecca A; Kotey, Stanley; Ramirez, Julio A

2017-06-01

During 2016, approximately 140,000 individuals entered the United States as part of the federal government refugee resettlement program and established themselves in communities in virtually every state. No national database regarding refugee health currently exists; therefore, little is known about existing infectious diseases, conditions, and cultural practices that impact successful acculturation. The objective of this report is to identify what is currently known about refugees and circumstances important to infection prevention and control with respect to their roles as new community members, employees, and consumers of health care. Using data from the University of Louisville Global Health Center's Newly Arriving Refugee Surveillance System, health issues affecting refugees from the perspective of a community member, an employee, and a patient were explored. Lack of immunity to vaccine-preventable diseases is the most widespread issue impacting almost every adult, adolescent, and child refugee resettled in Kentucky. Health issues of concern from an infection prevention and control perspective include latent tuberculosis infection, HIV, hepatitis B, hepatitis C, syphilis, and parasites. Other health conditions that may also be important include anemia, obesity, oral health, diabetes, and cardiovascular disease. Refugee resettlement provides motivation for collaborative work among those responsible for infection prevention and control in all settings, their public health partners, and those responsible for and interested in community workforce concerns. Copyright © 2017 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

Assessing environmental risk of the retired filter bed area, Battelle West Jefferson

International Nuclear Information System (INIS)

Miller, S.F.; Thompson, M.D.; Glennon, M.A.

1997-04-01

Initial investigations conducted by the U.S. Department of Energy, Chicago Operations Office, and by Argonne National Laboratory used seismic refraction profiling, electrical resistivity depth sounding, conductivity profiling, magnetic gradiometry, and ground-penetrating radar to study environmental geophysics in the area of the Battelle West Jefferson site's radiologically contaminated retired filter beds. The investigators used a combination of nonintrusive technologies and innovative drilling techniques to assess environmental risk at the filter beds and to improve understanding of the geology of the Big Darby Creek floodplain. The geophysical investigation, which showed that the preferred groundwater pathway is associated with a laterally extensive deposit of silty sand to sand that is less than 12 ft deep in the floodplain area, also guided the location of cone penetrometer test sites and piezometer installation. Cone penetrometer testing was useful for comparing continuous logging data with surface geophysical data in establishing correlations among unconsolidated materials

Research on Al-alloy sheet forming formability during warm/hot sheet hydroforming based on elliptical warm bulging test

Science.gov (United States)

Cai, Gaoshen; Wu, Chuanyu; Gao, Zepu; Lang, Lihui; Alexandrov, Sergei

2018-05-01

An elliptical warm/hot sheet bulging test under different temperatures and pressure rates was carried out to predict Al-alloy sheet forming limit during warm/hot sheet hydroforming. Using relevant formulas of ultimate strain to calculate and dispose experimental data, forming limit curves (FLCS) in tension-tension state of strain (TTSS) area are obtained. Combining with the basic experimental data obtained by uniaxial tensile test under the equivalent condition with bulging test, complete forming limit diagrams (FLDS) of Al-alloy are established. Using a quadratic polynomial curve fitting method, material constants of fitting function are calculated and a prediction model equation for sheet metal forming limit is established, by which the corresponding forming limit curves in TTSS area can be obtained. The bulging test and fitting results indicated that the sheet metal FLCS obtained were very accurate. Also, the model equation can be used to instruct warm/hot sheet bulging test.

On Jovian plasma sheet structure

International Nuclear Information System (INIS)

Khurana, K.K.; Kivelson, M.G.

1989-01-01

The authors evaluate several models of Jovian plasma sheet structure by determining how well they organize several aspects of the observed Voyager 2 magnetic field characteristics as a function of Jovicentric radial distance. It is shown that in the local time sector of the Voyager 2 outbound pass (near 0300 LT) the published hinged-magnetodisc models with wave (i.e., models corrected for finite wave velocity effects) are more successful than the published magnetic anomaly model in predicting locations of current sheet crossings. They also consider the boundary between the plasma sheet and the magnetotail lobe which is expected to vary slowly with radial distance. They use this boundary location as a further test of the models of the magnetotail. They show that the compressional MHD waves have much smaller amplitude in the lobes than in the plasma sheet and use this criterion to refine the identification of the plasma-sheet-lobe boundary. When the locations of crossings into and out of the lobes are examined, it becomes evident that the magnetic-anomaly model yields a flaring plasma sheet with a halfwidth of ∼ 3 R J at a radial distance of 20 R J and ∼ 12 R J at a radial distance of 100 R J . The hinged-magnetodisc models with wave, on the other hand, predict a halfwidth of ∼ 3.5 R J independent of distance beyond 20 R J . New optimized versions of the two models locate both the current sheet crossings and lobe encounters equally successfully. The optimized hinged-magnetodisc model suggests that the wave velocity decreases with increasing radial distance. The optimized magnetic anomaly model yields lower velocity contrast than the model of Vasyliunas and Dessler (1981)

78 FR 49509 - Lock+ Hydro Friends Fund XXX, LLC; FFP Project 121, LLC; Notice Announcing Preliminary Permit...

Science.gov (United States)

2013-08-14

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [ Project No. 13625-003; Project No. 14504-000] Lock+ Hydro Friends Fund XXX, LLC; FFP Project 121, LLC; Notice Announcing Preliminary Permit... and Jefferson County, Ohio. The applications were filed by Lock+ Hydro Friends Fund XXX, LLC for...

75 FR 16493 - Announcement of Funding Awards for the Public and Indian Housing Family Self-Sufficiency Program...

Science.gov (United States)

2010-04-01

... Orleans..... LA 70122 68,000 Orleans. Jefferson Parish Housing 1718 Betty Street.... Marrero......... LA 70072 45,893 Authority. Shreveport Housing Authority. 2500 Line Avenue..... Shreveport...... LA 71104 36... Vista Street Santa Fe........ NM 87505 55,908 Authority. Santa Fe County Housing 52 Camino De Jacobo...

77 FR 4283 - Procurement List; Additions

Science.gov (United States)

2012-01-27

.... of Jefferson County, Fort Atkinson, WI. Contracting Activity: Defense Logistics Agency Land and... aggregated by the Defense Logistics Agency Land and Maritime, Columbus, OH. NSN: 8040-00-NIB-0019--Dispenser... Activity: General Services Administration, Kansas City, MO. Coverage: B-List for the Broad Government...

Rubella - Fact Sheet for Parents

Science.gov (United States)

... and 4 through 6 years Fact Sheet for Parents Color [2 pages] Español: Rubéola The best way ... according to the recommended schedule. Fact Sheets for Parents Diseases and the Vaccines that Prevent Them Chickenpox ...

Cell sheet technology and cell patterning for biofabrication

Energy Technology Data Exchange (ETDEWEB)

Hannachi, Imen Elloumi; Yamato, Masayuki; Okano, Teruo [Institute of Advanced Biomedical Engineering and Science, Tokyo Women' s Medical University, 8-1 Kawada-cho, Shinjuku, Tokyo (Japan)

2009-06-01

We have developed cell sheet technology as a modern method for the fabrication of functional tissue-like and organ-like structures. This technology allows for a sheet of interconnected cells and cells in full contact with their natural extracellular environment to be obtained. A cell sheet can be patterned and composed according to more than one cell type. The key technology of cell sheet engineering is that a fabricated cell sheet can be harvested and transplanted utilizing temperature-responsive surfaces. In this review, we summarize different aspects of cell sheet engineering and provide a survey of the application of cell sheets as a suitable material for biofabrication and clinics. Moreover, since cell micropatterning is a key tool for cell sheet engineering, in this review we focus on the introduction of our approaches to cell micropatterning and cell co-culture to the principles of automation and how they can be subjected to easy robotics programming. Finally, efforts towards making cell sheet technology suitable for biofabrication and robotic biofabrication are also summarized. (topical review)

75 FR 18166 - Notice of Availability of the Draft Supplemental Environmental Impact Statement for the Proposed...

Science.gov (United States)

2010-04-09

... Section, Regulatory Branch, Louisville District, P.O. Box 59, Louisville, KY 40201-0059. The Public..., Regulatory Branch, Louisville District, P.O. Box 59, Louisville, KY 40201-0059. Phone (502) 315-6676, e-mail... jurisdictional streams, including 17,811 linear feet of perennial stream. The construction of the intake/outfall...

Energy information sheets

Energy Technology Data Exchange (ETDEWEB)

1993-12-02

The National Energy Information Center (NEIC), as part of its mission, provides energy information and referral assistance to Federal, State, and local governments, the academic community, business and industrial organizations, and the general public. Written for the general public, the EIA publication Energy Information Sheets was developed to provide information on various aspects of fuel production, prices, consumption and capability. The information contained herein pertains to energy data as of December 1991. Additional information on related subject matter can be found in other EIA publications as referenced at the end of each sheet.

Weld Repair of Thin Aluminum Sheet

Science.gov (United States)

Beuyukian, C. S.; Mitchell, M. J.

1986-01-01

Weld repairing of thin aluminum sheets now possible, using niobium shield and copper heat sinks. Refractory niobium shield protects aluminum adjacent to hole, while copper heat sinks help conduct heat away from repair site. Technique limits tungsten/inert-gas (TIG) welding bombardment zone to melt area, leaving surrounding areas around weld unaffected. Used successfully to repair aluminum cold plates on Space Shuttle, Commercial applications, especially in sealing fractures, dents, and holes in thin aluminum face sheets or clad brazing sheet in cold plates, heat exchangers, coolers, and Solar panels. While particularly suited to thin aluminum sheet, this process also used in thicker aluminum material to prevent surface damage near weld area.

12 GeV detector technology at Jefferson Lab

Energy Technology Data Exchange (ETDEWEB)

Leckey, John P. [Indiana University, Bloomington, IN 47405 (United States); Collaboration: GlueX Collaboration

2013-04-19

The Thomas Jefferson National Accelerator Facility (JLab) is presently in the middle of an upgrade to increase the energy of its CW electron beam from 6 GeV to 12 GeV along with the addition of a fourth experimental hall. Driven both by necessity and availability, novel detectors and electronics modules have been used in the upgrade. One such sensor is the Silicon Photomultiplier (SiPM), specifically a Multi-Pixel Photon Counter (MPPC), which is an array of avalanche photodiode pixels operating in Geiger mode that are used to sense photons. The SiPMs replace conventional photomultiplier tubes and have several distinct advantages including the safe operation in a magnetic field and the lack of need for high voltage. Another key to 12 GeV success is advanced fast electronics. Jlab will use custom 250 MHz and 125 MHz 12-bit analog to digital converters (ADCs) and time to digital converters (TDCs) all of which take advantage of VME Switched Serial (VXS) bus with its GB/s high bandwidth readout capability. These new technologies will be used to readout drift chambers, calorimeters, spectrometers and other particle detectors at Jlab once the 12 GeV upgrade is complete. The largest experiment at Jlab utilizing these components is GlueX - an experiment in the newly constructed Hall D that will study the photoproduction of light mesons in the search for hybrid mesons. The performance of these components and their respective detectors will be presented.

Experiment E89-044 on the Quasielastic ³He(e,e'p) Reaction at Jefferson Laboratory

Energy Technology Data Exchange (ETDEWEB)

Penel-Nottaris, Emilie [Univ. Joseph Fourier Grenoble (France)

2004-07-07

The Jefferson Lab Hall A E89-044 experiment has measured the ³He(e,e'p) reaction cross-sections. The extraction of the longitudinal and transverse response functions for the two-body break-up ³He(e,e'p)d reaction in parallel kinematics allows the study of the bound proton electromagnetic properties inside the ³He nucleus and the involved nuclear mechanisms beyond plane wave approximations.

75 FR 25308 - Environmental Impact Statement: Winnebago County, IL and Rock County, WI

Science.gov (United States)

2010-05-07

... DEPARTMENT OF TRANSPORTATION Federal Highway Administration Environmental Impact Statement: Winnebago County, IL and Rock County, WI AGENCY: Federal Highway Administration (FHWA), DOT. ACTION: Notice... Nye School Road northwest of Beloit, Rock County, Wisconsin to the interchange of Rockton Road and I...

ROE County Data

Data.gov (United States)

U.S. Environmental Protection Agency — This polygon dataset shows the outlines of states, counties, and county equivalents (Louisiana parishes, Alaska boroughs, Puerto Rico municipalities, and U.S. Virgin...

Modeling the Alzheimer Abeta17-42 fibril architecture: tight intermolecular sheet-sheet association and intramolecular hydrated cavities.

Science.gov (United States)

Zheng, Jie; Jang, Hyunbum; Ma, Buyong; Tsai, Chung-Jun; Nussinov, Ruth

2007-11-01

We investigate Abeta(17-42) protofibril structures in solution using molecular dynamics simulations. Recently, NMR and computations modeled the Abeta protofibril as a longitudinal stack of U-shaped molecules, creating an in-parallel beta-sheet and loop spine. Here we study the molecular architecture of the fibril formed by spine-spine association. We model in-register intermolecular beta-sheet-beta-sheet associations and study the consequences of Alzheimer's mutations (E22G, E22Q, E22K, and M35A) on the organization. We assess the structural stability and association force of Abeta oligomers with different sheet-sheet interfaces. Double-layered oligomers associating through the C-terminal-C-terminal interface are energetically more favorable than those with the N-terminal-N-terminal interface, although both interfaces exhibit high structural stability. The C-terminal-C-terminal interface is essentially stabilized by hydrophobic and van der Waals (shape complementarity via M35-M35 contacts) intermolecular interactions, whereas the N-terminal-N-terminal interface is stabilized by hydrophobic and electrostatic interactions. Hence, shape complementarity, or the "steric zipper" motif plays an important role in amyloid formation. On the other hand, the intramolecular Abeta beta-strand-loop-beta-strand U-shaped motif creates a hydrophobic cavity with a diameter of 6-7 A, allowing water molecules and ions to conduct through. The hydrated hydrophobic cavities may allow optimization of the sheet association and constitute a typical feature of fibrils, in addition to the tight sheet-sheet association. Thus, we propose that Abeta fiber architecture consists of alternating layers of tight packing and hydrated cavities running along the fibrillar axis, which might be possibly detected by high-resolution imaging.

75 FR 49016 - County of Greenville, S.C.-Acquisition Exemption-Greenville County Economic Development Corporation

Science.gov (United States)

2010-08-12

... Greenville, S.C.--Acquisition Exemption--Greenville County Economic Development Corporation The County of... verified notice of exemption under 49 CFR 1150.31 to acquire from Greenville County Economic Development... System Act, 16 U.S.C. 1247(d). See Greenville County Economic Development Corporation--Abandonment and...

The New 2nd-Generation SRF RandD Facility at Jefferson Lab: TEDF

International Nuclear Information System (INIS)

Reece, Charles E.; Reilly, Anthony V.

2012-01-01

The US Department of Energy has funded a near-complete renovation of the SRF-based accelerator research and development facilities at Jefferson Lab. The project to accomplish this, the Technical and Engineering Development Facility (TEDF) Project has completed the first of two phases. An entirely new 3,100 m 2 purpose-built SRF technical work facility has been constructed and was occupied in summer of 2012. All SRF work processes with the exception of cryogenic testing have been relocated into the new building. All cavity fabrication, processing, thermal treatment, chemistry, cleaning, and assembly work is collected conveniently into a new LEED-certified building. An innovatively designed 800 m2 cleanroom/chemroom suite provides long-term flexibility for support of multiple RandD and construction projects as well as continued process evolution. The characteristics of this first 2nd-generation SRF facility are described

The Carolina Sandhills: Quaternary eolian sand sheets and dunes along the updip margin of the Atlantic Coastal Plain province, southeastern United States

Science.gov (United States)

Swezey, Christopher; Fitzwater, Bradley A.; Whittecar, G. Richard; Mahan, Shannon; Garrity, Christopher P.; Aleman Gonzalez, Wilma B.; Dobbs, Kerby M.

2016-01-01

The Carolina Sandhills is a physiographic region of the Atlantic Coastal Plain province in the southeastern United States. In Chesterfield County (South Carolina), the surficial sand of this region is the Pinehurst Formation, which is interpreted as eolian sand derived from the underlying Cretaceous Middendorf Formation. This sand has yielded three clusters of optically stimulated luminescence ages: (1) 75 to 37 thousand years ago (ka), coincident with growth of the Laurentide Ice Sheet; (2) 28 to 18 ka, coincident with the last glacial maximum (LGM); and (3) 12 to 6 ka, mostly coincident with the Younger Dryas through final collapse of the Laurentide Ice Sheet. Relict dune morphologies are consistent with winds from the west or northwest, coincident with modern and inferred LGM January wind directions. Sand sheets are more common than dunes because of effects of coarse grain size (mean range: 0.35–0.59 mm) and vegetation. The coarse grain size would have required LGM wind velocities of at least 4–6 m/sec, accounting for effects of colder air temperatures on eolian sand transport. The eolian interpretation of the Carolina Sandhills is consistent with other evidence for eolian activity in the southeastern United States during the last glaciation.

Sheet pinch devices

International Nuclear Information System (INIS)

Anderson, O.A.; Baker, W.R.; Ise, J. Jr.; Kunkel, W.B.; Pyle, R.V.; Stone, J.M.

1958-01-01

Three types of sheet-like discharges are being studied at Berkeley. The first of these, which has been given the name 'Triax', consists of a cylindrical plasma sleeve contained between two coaxial conducting cylinders A theoretical analysis of the stability of the cylindrical sheet plasma predicts the existence of a 'sausage-mode' instability which is, however, expected to grow more slowly than in the case of the unstabilized linear pinch (by the ratio of the radial dimensions). The second pinch device employs a disk shaped discharge with radial current guided between flat metal plates, this configuration being identical to that of the flat hydromagnetic capacitor without external magnetic field. A significant feature of these configurations is the absence of a plasma edge, i.e., there are no regions of sharply curved magnetic field lines anywhere in these discharges. The importance of this fact for stability is not yet fully investigated theoretically. As a third configuration a rectangular, flat pinch tube has been constructed, and the behaviour of a flat plasma sheet with edges is being studied experimentally

Jefferson Teamwork Observation Guide (JTOG): An Instrument to Observe Teamwork Behaviors.

Science.gov (United States)

Lyons, Kevin J; Giordano, Carolyn; Speakman, Elizabeth; Smith, Kellie; Horowitz, June A

2016-01-01

Interprofessional education (IPE) is becoming an integral part of the education of health professions students. However, teaching students to become successful members of interprofessional teams is complex, and it is important for students to learn the combinations of skills necessary for teams to function effectively. There are many instruments available to measure many features related to IPE. However, these instruments are often too cumbersome to use in an observational situation since they tend to be lengthy and contain many abstract characteristics that are difficult to identify. The Jefferson Teamwork Observation Guide (JTOG) is a short tool that was created for students early in their educational program to observe teams in action with a set of guidelines to help them focus their observation on behaviors indicative of good teamwork. The JTOG was developed over a 2-year period based on student and clinician feedback and the input of experts in IPE. While initially developed as a purely educational tool for prelicensure students, it is becoming clear that it is an easy-to-use instrument that assesses the behavior of clinicians in practice.

The cryogenic target for the G0 experiment at Jefferson lab

International Nuclear Information System (INIS)

Covrig, S.D.; Beise, E.J.; Carr, R.; Gustafsson, K.K.; Hannelius, L.; Herda, M.-C.; Jones, C.E.; Liu, J.; McKeown, R.D.; Neveling, R.; Rauf, A.W.; Smith, G.

2005-01-01

A cryogenic horizontal single loop target has been designed, built, tested and operated for the G 0 experiment in Hall C at Jefferson Lab. The target cell is 20cm long, the loop volume is 6.5l and the target operates with the cryogenic pump fully immersed in the fluid. The target has been designed to operate at 30Hz rotational pump speed with either liquid hydrogen or liquid deuterium. The high-power heat exchanger is able to remove 1000W of heat from the liquid hydrogen, while the nominal electron beam with current of 40μA and energy of 3GeV deposits about 320W of heat into the liquid. The increase in the systematic uncertainty due to the liquid hydrogen target is negligible on the scale of a parity violation experiment. The global normalized yield reduction for 40μA beam is about 1.5% and the target density fluctuations contribute less than 238ppm (parts per million) to the total asymmetry width, typically about 1200ppm, in a Q 2 bin

Taos County Roads

Data.gov (United States)

Earth Data Analysis Center, University of New Mexico — Vector line shapefile under the stewardship of the Taos County Planning Department depicting roads in Taos County, New Mexico. Originally under the Emergency...

Future Measurements of the Nucleon Elastic Electromagnetic Form Factors at Jefferson Lab

Science.gov (United States)

Gilfoyle, Gerard

2018-01-01

The elastic, electromagnetic form factors are fundamental observables that describe the internal structure of protons, neutrons, and atomic nuclei. Jefferson Lab in the United States has completed the 12 GeV Upgrade that will open new opportunities to study the form factors. A campaign to measure all four nucleon form factors (electric and magnetic ones for both proton and neutron) has been approved consisting of seven experiments in Halls A, B, and C. The increased energy of the electron beam will extend the range of precision measurements to higher Q2 for all four form factors together. This combination of measurements will allow for the decomposition of the results into their quark components and guide the development of a QCD-based understanding of nuclei in the non-perturbative regime. I will present more details on the 12 GeV Upgrade, the methods used to measure the form factors, and what we may learn.

Spin observables in charged pion photo-production from polarized neutrons in solid HD at Jefferson Lab

Energy Technology Data Exchange (ETDEWEB)

Kageya, Tsuneo [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Ho, Dao [Carnegie Mellon Univ., Pittsburgh, PA (United States); Peng, Peng [Univ. of Virginia, Charlottesville, VA (United States); Klein, Franz [George Washington Univ., Washington, DC (United States); Sandorfi, Andrew M. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Schumacher, Reinhard A. [Carnegie Mellon Univ., Pittsburgh, PA (United States)

2018-04-01

E asymmetries have been extracted from double-polarizationexperiments in Hall-B of the Thomas Jefferson National Accelerator Facility (JLab). Results have been obtained from the E06-101 (g14) experiment, using circularly polarized photon beams, longitudinally polarized Deuterons in solid HD targets, and the CEBAF Large Acceptance Spectrometer (CLAS). The results cover a range inW from 1.48 to 2.32 GeV. Three independent analyses, using distinctly different methods, have been combined to obtain the final values, which have been published recently. Partial wave analyses (PWA), which have had to rely on a sparse neutron data base, havebeen significantly changed with the inclusion of these g14 asymmetries.

Effect of Cell Sheet Manipulation Techniques on the Expression of Collagen Type II and Stress Fiber Formation in Human Chondrocyte Sheets.

Science.gov (United States)

Wongin, Sopita; Waikakul, Saranatra; Chotiyarnwong, Pojchong; Siriwatwechakul, Wanwipa; Viravaidya-Pasuwat, Kwanchanok

2018-03-01

Cell sheet technology is applied to human articular chondrocytes to construct a tissue-like structure as an alternative treatment for cartilage defect. The effect of a gelatin manipulator, as a cell sheet transfer system, on the quality of the chondrocyte sheets was investigated. The changes of important chondrogenic markers and stress fibers, resulting from the cell sheet manipulation, were also studied. The chondrocyte cell sheets were constructed with patient-derived chondrocytes using a temperature-responsive polymer and a gelatin manipulator as a transfer carrier. The properties of the cell sheets, including sizes, expression levels of collagen type II and I, and the localization of the stress fibers, were assessed and compared with those of the cell sheets harvested without the gelatin manipulator. Using the gelatin manipulator, the original size of the chondrocyte cell sheets was retained with abundant stress fibers, but with a decrease in the expression of collagen type II. Without the gelatin manipulator, although the cell shrinkage occurred, the cell sheet with suppressed stress fiber formation showed significantly higher levels of collagen type II. These results support our observations that stress fiber formation in chondrocyte cell sheets affected the production of chondrogenic markers. These densely packed tissue-like structures possessed a good chondrogenic activity, indicating their potential for use in autologous chondrocyte implantation to treat cartilage defects.

Allegheny County Plumbers

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — All master plumbers must be registered with the Allegheny County Health Department. Only Registered Master Plumbers who possess a current plumbing license or...

Settlement during vibratory sheet piling

NARCIS (Netherlands)

Meijers, P.

2007-01-01

During vibratory sheet piling quite often the soil near the sheet pile wall will settle. In many cases this is not a problem. For situations with houses, pipelines, roads or railroads at relative short distance these settlements may not be acceptable. The purpose of the research described in this

The G0 experiment at Jefferson laboratory: Measurement of the weak neutral form factors of the nucleon

International Nuclear Information System (INIS)

Furget, C.

2005-01-01

The G0 experiment aims to measure parity-violating asymmetries in elastic electron-proton and quasi-elastic electron-deuteron scattering. This experimental program allows to perform the separation of the electric and magnetic weak neutral and axial form factors for three different momentum transfers 0.3, 0.5 and 0.8 (GeV/c)2. The first part of the experiment has been performed in Hall C of Jefferson Laboratory with a commissioned setup. A preliminary analysis of the data has provided a first estimate of the main systematic uncertainties. The analysis to determine the actual physics asymmetries is proceeding

County Population Vulnerability

Data.gov (United States)

City and County of Durham, North Carolina — This layer summarizes the social vulnerability index for populations within each county in the United States at scales 1:3m and below. It answers the question...

49 CFR 1243.2 - Condensed balance sheet.

Science.gov (United States)

2010-10-01

... 49 Transportation 9 2010-10-01 2010-10-01 false Condensed balance sheet. 1243.2 Section 1243.2... § 1243.2 Condensed balance sheet. Commencing with reports for the 3 months beginning January 1, 1972, and... hereby, required to compile and file quarterly reports of balance sheet items in accordance with...

Electron energization in the geomagnetic tail current sheet

International Nuclear Information System (INIS)

Lyons, L.R.

1984-01-01

Electron motion in the distant tail current sheet is evaluated and found to violate the guiding center approximation at energies > or approx. =100 eV. Most electrons within the energy range approx.10 -1 -10 2 keV that enter the current sheet become trapped within the magnetic field reversal region. These electrons then convect earthward and gain energy from the cross-tail electric field. If the energy spectrum of electrons entering the current sheet is similar to that of electrons from the boundary layer surrounding the magnetotail, the energy gain from the electric field produces electron energy spectra comparable to those observed in the earth's plasma sheet. Thus current sheet interactions can be a significant source of particles and energy for plasma sheet electrons as well as for plasma sheet ions. A small fraction of electrons within the current sheet has its pitch angles scattered so as to be ejected from the current sheet within the atmospheric loss cone. These electrons can account for the electron precipitation near the high-latitude boundary of energetic electrons, which is approximately isotropic in pitch angle up to at least several hundred keV. Current sheet interaction should cause approximately isotropic auroral precipitation up to several hundred keV energies, which extends to significantly lower latitudes for ions than for electrons in agreement with low-altitude satellite observations. Electron precipitation associated with diffuse aurora generally has a transition at 1-10 keV to anisotropic pitch angle distributions. Such electron precipitation cannot be explained by current sheet interactions, but it can be explained by pitch angle diffusion driven by plasma turbulence

Allegheny County Greenways

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — Greenways data was compiled by the Allegheny Land Trust as a planning effort in the development of Allegheny Places, the Allegheny County Comprehensive Plan. The...

Bessel light sheet structured illumination microscopy

Science.gov (United States)

Noshirvani Allahabadi, Golchehr

Biomedical study researchers using animals to model disease and treatment need fast, deep, noninvasive, and inexpensive multi-channel imaging methods. Traditional fluorescence microscopy meets those criteria to an extent. Specifically, two-photon and confocal microscopy, the two most commonly used methods, are limited in penetration depth, cost, resolution, and field of view. In addition, two-photon microscopy has limited ability in multi-channel imaging. Light sheet microscopy, a fast developing 3D fluorescence imaging method, offers attractive advantages over traditional two-photon and confocal microscopy. Light sheet microscopy is much more applicable for in vivo 3D time-lapsed imaging, owing to its selective illumination of tissue layer, superior speed, low light exposure, high penetration depth, and low levels of photobleaching. However, standard light sheet microscopy using Gaussian beam excitation has two main disadvantages: 1) the field of view (FOV) of light sheet microscopy is limited by the depth of focus of the Gaussian beam. 2) Light-sheet images can be degraded by scattering, which limits the penetration of the excitation beam and blurs emission images in deep tissue layers. While two-sided sheet illumination, which doubles the field of view by illuminating the sample from opposite sides, offers a potential solution, the technique adds complexity and cost to the imaging system. We investigate a new technique to address these limitations: Bessel light sheet microscopy in combination with incoherent nonlinear Structured Illumination Microscopy (SIM). Results demonstrate that, at visible wavelengths, Bessel excitation penetrates up to 250 microns deep in the scattering media with single-side illumination. Bessel light sheet microscope achieves confocal level resolution at a lateral resolution of 0.3 micron and an axial resolution of 1 micron. Incoherent nonlinear SIM further reduces the diffused background in Bessel light sheet images, resulting in

Magnetic configurations of the tilted current sheets in magnetotail

Directory of Open Access Journals (Sweden)

C. Shen

2008-11-01

Full Text Available In this research, the geometrical structures of tilted current sheet and tail flapping waves have been analysed based on multiple spacecraft measurements and some features of the tilted current sheets have been made clear for the first time. The geometrical features of the tilted current sheet revealed in this investigation are as follows: (1 The magnetic field lines (MFLs in the tilted current sheet are generally plane curves and the osculating planes in which the MFLs lie are about vertical to the equatorial plane, while the normal of the tilted current sheet leans severely to the dawn or dusk side. (2 The tilted current sheet may become very thin, the half thickness of its neutral sheet is generally much less than the minimum radius of the curvature of the MFLs. (3 In the neutral sheet, the field-aligned current density becomes very large and has a maximum value at the center of the current sheet. (4 In some cases, the current density is a bifurcated one, and the two humps of the current density often superpose two peaks in the gradient of magnetic strength, indicating that the magnetic gradient drift current is possibly responsible for the formation of the two humps of the current density in some tilted current sheets. Tilted current sheets often appear along with tail current sheet flapping waves. It is found that, in the tail flapping current sheets, the minimum curvature radius of the MFLs in the current sheet is rather large with values around 1 RE, while the neutral sheet may be very thin, with its half thickness being several tenths of RE. During the flapping waves, the current sheet is tilted substantially, and the maximum tilt angle is generally larger than 45°. The phase velocities of these flapping waves are several tens km/s, while their periods and wavelengths are several tens of minutes, and several earth radii, respectively. These tail flapping events generally last several hours and occur during quiet periods or periods of

Development of a Metacognitive Effort Construct of Empathy during Clinical Training: A Longitudinal Study of the Factor Structure of the Jefferson Scale of Empathy

Science.gov (United States)

Stansfield, R. Brent; Schwartz, Alan; O'Brien, Celia Laird; Dekhtyar, Michael; Dunham, Lisette; Quirk, Mark

2016-01-01

Empathy is crucial for effective clinical care but appears to decline during undergraduate medical training. Understanding the nature of this decline is necessary for addressing it. The Jefferson Scale of Empathy (JSE) is used to measure medical students' clinical empathy attitudes. One recent study described a 3-factor model of the JSE. This…

Relativistic current sheets in electron-positron plasmas

International Nuclear Information System (INIS)

Zenitani, S.

2008-01-01

The current sheet structure with magnetic field reversal is one of the fundamental structure in space and astrophysical plasmas. It draws recent attention in high-energy astrophysical settings, where relativistic electron-positron plasmas are considered. In this talk we will review the recent progress of the physical processes in the relativistic current sheet. The kinetic stability of a single current sheet, the nonlinear behavior of these instabilities, and recent challenges on the multi current sheet systems are introduced. We will also introduce some problems of magnetic reconnection in these relativistic environments. (author)

Eleven Years of Data on the Jefferson Scale of Empathy-Medical Student Version (JSE-S): Proxy Norm Data and Tentative Cutoff Scores.

Science.gov (United States)

Hojat, Mohammadreza; Gonnella, Joseph S

2015-01-01

This study was designed to provide typical descriptive statistics, score distributions and percentile ranks of the Jefferson Scale of Empathy-Medical Student version (JSE-S) of male and female medical school matriculants to serve as proxy norm data and tentative cutoff scores. The participants were 2,637 students (1,336 women and 1,301 men) who matriculated at Sidney Kimmel (formerly Jefferson) Medical College between 2002 and 2012, and completed the JSE at the beginning of medical school. Information extracted from descriptive statistics, score distributions and percentile ranks for male and female matriculants were used to develop proxy norm data and tentative cutoff scores. The score distributions of the JSE tended to be moderately skewed and platykurtic. Women obtained a significantly higher mean score (116.2 ± 9.7) than men (112.3 ± 10.8) on the JSE-S (t2,635 = 9.9, p norm data. The tentative cutoff score to identify low scorers was ≤ 95 for men and ≤ 100 for women. Our findings provide norm data and cutoff scores for admission decisions under certain conditions and for identifying students in need of enhancing their empathy. © 2015 S. Karger AG, Basel.

Allegheny County Hospitals

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — The data on health care facilities includes the name and location of all the hospitals and primary care facilities in Allegheny County. The current listing of...

Tube sheet design for PFBR steam generator

International Nuclear Information System (INIS)

Chellapandi, P.; Chetal, S.C.; Bhoje, S.B.

1991-01-01

Top and bottom tube sheets of PFBR Steam Generators have been analysed with 3D and axisymmetric models using CASTEM Programs. Analysis indicates that the effects of piping reactions at the inlet/outlet nozzles on the primary stresses in the tube sheets are negligible and the asymmetricity of the deformation pattern introduced in the tube sheet by the presence of inlet/outlet and manhole nozzles is insignificant. The minimum tube sheet thicknesses for evaporator and reheater are 135 mm and 75 mm respectively. Further analysis has indicated the minimum fillet radius at the junction of tube sheet and dished end should be 20 mm. Simplified methodology has been developed to arrive at the number of thermal baffles required to protect the tube sheet against fatigue damage due to thermal transient. This method has been applied to PFBR steam generators to determine the required number of thermal baffles. For protecting the bottom tube sheet of evaporator against the thermal shock due to feed water and secondary pump trip, one thermal shield is found to be sufficient. Further analysis is required to decide upon the actual number to take care of the severe thermal transient, following the event of sudden dumping of water/steam, immediately after the sodium-water reaction. (author)

17 CFR 210.5-02 - Balance sheets.

Science.gov (United States)

2010-04-01

... customers at the date of the balance sheet. Include a general description of the prerequisites for billing... 17 Commodity and Securities Exchanges 2 2010-04-01 2010-04-01 false Balance sheets. 210.5-02... Balance sheets. The purpose of this rule is to indicate the various line items and certain additional...

78 FR 43901 - Changes in Flood Hazard Determinations

Science.gov (United States)

2013-07-22

.../index.php/ Leeds, 1040 Park Leeds, AL 35094. alabama/ Drive, Leeds, AL jefferson-3/. 35094. Arizona... Street, om/index.php/ Thornton, 9500 Thornton, CO colorado/adams/. Civic Center 80241. Drive, Thornton.../index.php/ 0273P). County Board of 13th Street, colorado/boulder/ Commissioners, Suite 203, . P.O. Box...

URANIUM REMOVAL FROM DRINKING WATER USING A SMALL FULL-SCALE SYSTEM

Science.gov (United States)

This report presents background and history of water quality, the basis for design and nine months of actual operating data for a small, full-scale strong-base ion exchange system that is used to remove uranium from a water supply serving a school in Jefferson County, CO. Informa...

Pressure balance between lobe and plasma sheet

International Nuclear Information System (INIS)

Baumjohann, W.; Paschmann, G.; Luehr, H.

1990-01-01

Using eight months of AMPTE/IRM plasma and magnetic field data, the authors have done a statistical survey on the balance of total (thermal and magnetic) pressure in the Earth's plasma sheet and tail lobe. About 300,000 measurements obtained in the plasma sheet and the lobe were compared for different levels of magnetic activity as well as different distances from the Earth. The data show that lobe and plasma sheet pressure balance very well. Even in the worst case they do not deviate by more than half of the variance in the data itself. Approximately constant total pressure was also seen during a quiet time pass when IRM traversed nearly the whole magnetotail in the vertical direction, from the southern hemisphere lobe through the neutral sheet and into the northern plasma sheet boundary layer

Thermomechanical processing of plasma sprayed intermetallic sheets

Science.gov (United States)

Hajaligol, Mohammad R.; Scorey, Clive; Sikka, Vinod K.; Deevi, Seetharama C.; Fleischhauer, Grier; Lilly, Jr., A. Clifton; German, Randall M.

2001-01-01

A powder metallurgical process of preparing a sheet from a powder having an intermetallic alloy composition such as an iron, nickel or titanium aluminide. The sheet can be manufactured into electrical resistance heating elements having improved room temperature ductility, electrical resistivity, cyclic fatigue resistance, high temperature oxidation resistance, low and high temperature strength, and/or resistance to high temperature sagging. The iron aluminide has an entirely ferritic microstructure which is free of austenite and can include, in weight %, 4 to 32% Al, and optional additions such as .ltoreq.1% Cr, .gtoreq.0.05% Zr .ltoreq.2% Ti, .ltoreq.2% Mo, .ltoreq.1% Ni, .ltoreq.0.75% C, .ltoreq.0.1% B, .ltoreq.1% submicron oxide particles and/or electrically insulating or electrically conductive covalent ceramic particles, .ltoreq.1% rare earth metal, and/or .ltoreq.3% Cu. The process includes forming a non-densified metal sheet by consolidating a powder having an intermetallic alloy composition such as by roll compaction, tape casting or plasma spraying, forming a cold rolled sheet by cold rolling the non-densified metal sheet so as to increase the density and reduce the thickness thereof and annealing the cold rolled sheet. The powder can be a water, polymer or gas atomized powder which is subjecting to sieving and/or blending with a binder prior to the consolidation step. After the consolidation step, the sheet can be partially sintered. The cold rolling and/or annealing steps can be repeated to achieve the desired sheet thickness and properties. The annealing can be carried out in a vacuum furnace with a vacuum or inert atmosphere. During final annealing, the cold rolled sheet recrystallizes to an average grain size of about 10 to 30 .mu.m. Final stress relief annealing can be carried out in the B2 phase temperature range.

17 CFR 210.7-03 - Balance sheets.

Science.gov (United States)

2010-04-01

... 17 Commodity and Securities Exchanges 2 2010-04-01 2010-04-01 false Balance sheets. 210.7-03... 1940, AND ENERGY POLICY AND CONSERVATION ACT OF 1975 Insurance Companies § 210.7-03 Balance sheets. (a... otherwise permitted by the Commission, should appear on the face of the balance sheets and in the notes...

Disposal sheet for preventing scattering of radioactive contaminated material

International Nuclear Information System (INIS)

Miyasaka, Shun-ichi; Kurioka, Hitoshi; Nakamura, Kenjiro.

1990-01-01

Upon disposal of vinyl sheets at the final stage of dismantling operation for nuclear buildings, etc., radioactive contaminated materials caused by cutting concretes, etc. remain on the sheets. In view of the above, members capable of restoring original shape due to the temperature difference are attached to the sheet main body so that the sheet main body may be folded into a bag-like shape. Since the members as described above are bent upon temperature elevation in the sheets, the sheet main body is pulled by the members and then spontaneously folded into a bag-like shape. As a result, the radioactive contaminated materials remaining on the sheets are wrapped into the sheet main body free from touch to operator's hands or without scattering to the surrounding. This can prevent operator's external and internal exposure. (T.M.)

Single Point Incremental Forming using a Dummy Sheet

DEFF Research Database (Denmark)

Skjødt, Martin; Silva, Beatriz; Bay, Niels

2007-01-01

A new version of single point incremental forming (SPIF) is presented. This version includes a dummy sheet on top of the work piece, thus forming two sheets instead of one. The dummy sheet, which is in contact with the rotating tool pin, is discarded after forming. The new set-up influences....... The possible influence of friction between the two sheets is furthermore investigated. The results show that the use of a dummy sheet reduces wear of the work piece to almost zero, but also causes a decrease in formability. Bulging of the planar sides of the pyramid is reduced and surface roughness...

Allegheny County Supermarkets & Convenience Stores

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — Location information for all Supermarkets and Convenience Stores in Allegheny County was produced using the Allegheny County Fee and Permit Data for 2016.

Neutron spatial distribution measurement with 6Li-contained thermoluminescent sheets

International Nuclear Information System (INIS)

Konnai, A.; Odano, N.; Sawamura, H.; Ozasa, N.; Ishikawa, Y.

2006-01-01

We have been developing a thermoluminescent (TL) sheet for photon dosimetry (TL sheet) with thermoluminescent material of LiF:Mg, Cu, P and a co-polymer of ethylene and tetrafluoroethylene. For the purpose of a development of simple method for neutron spatial distribution measurement, TL sheet for neutron detection (NTL sheet) is made by adding 94.7% enriched 6 LiF to TL sheet. TL material in TL sheet is directly excited by ionizing radiation whereas, in the case of neutron detection, TL material in NTL sheet is indirectly excited by neutron capture reaction. That is neutron distribution can be obtained with TL caused by α particle from 6 Li(n, α) 3 H reaction. Responses of NTL sheets to neutrons were examined at the neutron beam irradiation facility for Boron Neutron Capture Therapy (BNCT) in JRR-4 research reactor in Japan Atomic Energy Agency. TL and NTL sheets were exposed to striped and roundly distributed neutron fields. Attenuations of neutron flux in air and water were also observed using NTL sheets. TL sheets were also exposed on the same conditions and compared with NTL sheets. TL intensity ratios of NTL sheet to TL sheet were consistent with the calculated value from 6 Li content. Thermal neutron attenuation observed by NTL sheet also corresponded with the result measured by Au wire radioactivation and TLD chips, which were currently used in BNCT at JRR-4. These results were analyzed with by Monte Carlo simulation. The present results indicated that NTL sheet is applicable to measurement of neutron spatial distribution. (author)

A search for baryon- and lepton-number violating decays of $\\Lambda$ hyperons using the CLAS detector at Jefferson Laboratory

OpenAIRE

McCracken, M. E.; Bellis, M.; Adhikari, K. P.; Adikaram, D.; Akbar, Z.; Pereira, S. Anefalos; Badui, R. A.; Ball, J.; Baltzell, N. A.; Battaglieri, M.; Batourine, V.; Bedlinskiy, I.; Biselli, A. S.; Boiarinov, S.; Briscoe, W. J.

2015-01-01

We present a search for ten baryon-number violating decay modes of $\\Lambda$ hyperons using the CLAS detector at Jefferson Laboratory. Nine of these decay modes result in a single meson and single lepton in the final state ($\\Lambda \\rightarrow m \\ell$) and conserve either the sum or the difference of baryon and lepton number ($B \\pm L$). The tenth decay mode ($\\Lambda \\rightarrow \\bar{p}\\pi^+$) represents a difference in baryon number of two units and no difference in lepton number. We obser...

Soil Characterization Database for the Area 3 Radioactive Waste Management Site, Nevada Test Site, Nye County, Nevada

International Nuclear Information System (INIS)

Remortel, R. D. Van; Lee, Y. J.; Snyder, K. E.

2005-01-01

Soils were characterized in an investigation at the Area 3 Radioactive Waste Management Site at the U.S. Department of Energy Nevada Test Site in Nye County, Nevada. Data from the investigation are presented in four parameter groups: sample and site characteristics, U.S. Department of Agriculture (USDA) particle size fractions, chemical parameters, and American Society for Testing Materials-Unified Soil Classification System (ASTM-USCS) particle size fractions. Spread-sheet workbooks based on these parameter groups are presented to evaluate data quality, conduct database updates, and set data structures and formats for later extraction and analysis. This document does not include analysis or interpretation of presented data

Soil Characterization Database for the Area 5 Radioactive Waste Management Site, Nevada Test Site, Nye County, Nevada

International Nuclear Information System (INIS)

Lee, Y. J.; Remortel, R. D. Van; Snyder, K. E.

2005-01-01

Soils were characterized in an investigation at the Area 5 Radioactive Waste Management Site at the U.S. Department of Energy Nevada Test Site in Nye County, Nevada. Data from the investigation are presented in four parameter groups: sample and site characteristics, U.S. Department of Agriculture (USDA) particle size fractions, chemical parameters, and American Society for Testing Materials-Unified Soil Classification System (ASTM-USCS) particle size fractions. Spread-sheet workbooks based on these parameter groups are presented to evaluate data quality, conduct database updates,and set data structures and formats for later extraction and analysis. This document does not include analysis or interpretation of presented data

On the possible eigenoscillations of neutral sheets

International Nuclear Information System (INIS)

Almeida, W.A.; Costa, J.M. da; Aruquipa, E.G.; Sudano, J.P.

1974-12-01

A neutral sheet model with hyperbolic tangent equilibrium magnetic field and hyperbolic square secant density profiles is considered. It is shown that the equation for small oscillations takes the form of an eigenvalue oscillation problem. Computed eigenfrequencies of the geomagnetic neutral sheet were found to be in the range of the resonant frequencies of the geomagnetic plasma sheet computed by other authors

Uranium mining sites - Thematic sheets

International Nuclear Information System (INIS)

2009-01-01

A first sheet proposes comments, data and key numbers about uranium extraction in France: general overview of uranium mining sites, status of waste rock and tailings after exploitation, site rehabilitation. The second sheet addresses the sources of exposure to ionizing radiations due to ancient uranium mining sites: discussion on the identification of these sources associated with these sites, properly due to mining activities or to tailings, or due to the transfer of radioactive substances towards water and to the contamination of sediments, description of the practice and assessment of radiological control of mining sites. A third sheet addresses the radiological exposure of public to waste rocks, and the dose assessment according to exposure scenarios: main exposure ways to be considered, studied exposure scenarios (passage on backfilled path and grounds, stay in buildings built on waste rocks, keeping mineralogical samples at home). The fourth sheet addresses research programmes of the IRSN on uranium and radon: epidemiological studies (performed on mine workers; on French and on European cohorts, French and European studies on the risk of lung cancer associated with radon in housing), study of the biological effects of chronic exposures. The last sheet addresses studies and expertises performed by the IRSN on ancient uranium mining sites in France: studies commissioned by public authorities, radioactivity control studies performed by the IRSN about mining sites, participation of the IRSN to actions to promote openness to civil society

Allegheny County Blazed Trails Locations

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — Shows the location of blazed trails in all Allegheny County parks. This is the same data used in the Allegheny County Parks Trails Mobile App, available for Apple...

Best Manufacturing Practices. Report of Survey Conducted at Stafford County Public Schools, Stafford County, VA

National Research Council Canada - National Science Library

1994-01-01

During the week of August 8, 1994, a Best Manufacturing Practices (BMP) survey was conducted at the Stafford County Public Schools located in Stafford County, Virginia, considered one of the fastest growing counties in the state...

Sheet, ligament and droplet formation in swirling primary atomization

Directory of Open Access Journals (Sweden)

Changxiao Shao

2018-04-01

Full Text Available We report direct numerical simulations of swirling liquid atomization to understand the physical mechanism underlying the sheet breakup of a non-turbulent liquid swirling jet which lacks in-depth investigation. The volume-of-fluid (VOF method coupled with adapted mesh refinement (AMR technique in GERRIS code is employed in the present simulation. The mechanisms of sheet, ligament and droplet formation are investigated. It is observed that the olive-shape sheet structure is similar to the experimental result qualitatively. The numerical results show that surface tension, pressure difference and swirling effect contribute to the contraction and extension of liquid sheet. The ligament formation is partially at the sheet rim or attributed to the extension of liquid hole. Especially, the movement of hairpin vortex exerts by an anti-radial direction force to the sheet surface and leads to the sheet thinness. In addition, droplet formation is attributed to breakup of ligament and central sheet.

Sheet, ligament and droplet formation in swirling primary atomization

Science.gov (United States)

Shao, Changxiao; Luo, Kun; Chai, Min; Fan, Jianren

2018-04-01

We report direct numerical simulations of swirling liquid atomization to understand the physical mechanism underlying the sheet breakup of a non-turbulent liquid swirling jet which lacks in-depth investigation. The volume-of-fluid (VOF) method coupled with adapted mesh refinement (AMR) technique in GERRIS code is employed in the present simulation. The mechanisms of sheet, ligament and droplet formation are investigated. It is observed that the olive-shape sheet structure is similar to the experimental result qualitatively. The numerical results show that surface tension, pressure difference and swirling effect contribute to the contraction and extension of liquid sheet. The ligament formation is partially at the sheet rim or attributed to the extension of liquid hole. Especially, the movement of hairpin vortex exerts by an anti-radial direction force to the sheet surface and leads to the sheet thinness. In addition, droplet formation is attributed to breakup of ligament and central sheet.

76 FR 53423 - Notice of Intent To Prepare an Environmental Impact Statement/Environmental Impact Report for the...

Science.gov (United States)

2011-08-26

... Sacramento River Early Implementation Project, West Sacramento, CA AGENCY: Department of the Army, U.S. Army... Levee in the City of West Sacramento, Yolo County, CA. The project reach extends along the right bank of... p.m. at the West Sacramento Recreation Center, 2801 Jefferson Boulevard, West Sacramento, CA. Send...

76 FR 79579 - Approval and Promulgation of Implementation Plans and Designation of Areas for Air Quality...

Science.gov (United States)

2011-12-22

.... Louis City and Franklin, Jefferson, St. Charles and St. Louis Counties in Missouri. The Illinois... 16, 2011. (EPA will address the Missouri portion of the St. Louis area in a separate rulemaking... received will be included in the public docket without change and may be made available online at www...

The western juniper resource of eastern Oregon, 1999.

Science.gov (United States)

David L. Azuma; Bruce A. Hiserote; Paul A. Dunham

2005-01-01

This report summarizes resource statistics for eastern Oregon's juniper forests, which are in Baker, Crook, Deschutes, Gilliam, Grant, Harney, Jefferson, Klamath, Lake, Malheur, Morrow, Sherman, Umatilla, Union, Wallowa, Wasco, and Wheeler Counties. We sampled all ownerships outside of the National Forest System; we report the statistics on juniper forest on...

Timber resource statistics for western Washington.

Science.gov (United States)

Coffin D. MacLean; Patricia M. Bassett; Glenn. Yeary

1992-01-01

This report summarizes a 1988-90 timber resource inventory of 19 counties in western Washington: Clallam, Clark, Cowlitz, Grays Harbor, Island, Jefferson, King, Kitsap, Lewis, Mason, Pacific, Pierce, San Juan, Skagit, Skamania, Snohomish, Thurston, Wahkiakum, and Whatcom. Detailed tables of forest area, timber volume, growth, mortality, and harvest are presented.

Copper contamination in thin stainless steel sheet

International Nuclear Information System (INIS)

Holbert, R.K. Jr.; Dobbins, A.G.; Bennett, R.K. Jr.

1986-01-01

The standard welding technique used at Oak Ridge Y-12 Plant for joining thin stainless sheet is the gas tungsten arc (GTA) welding process. One of the reoccurring problems with the sheet welds is surface cracking in the heat-affected zone (HAZ). Metallography shows that the cracks are only about 0.05 mm (0.002 in.) deep which is significant in a 0.25 mm (0.01 in.) thick sheet. Thus, welding requirements do not permit any surfacing cracking as detected by a fluorescent dye penetrant test conducted on every part after welding. Surface cracks have been found in both of the two most common weld designs in the thin sheet fabricated at the Oak Ridge Y-12 Plant. These butt joints are welded between two 0.25 mm thick stainless steel sheets and a tube with eyelet welded to a 25 mm (0.98 in.) thick sheet. The weld between the two sheets is made on a semiautomatic seam welding unit, whereas the tube-to-eyelet-to-sheet welds are done manually. The quality of both welds is very dependent on the welding procedure and the way the parts are placed in the weld fixturing. Metallographic examination has indicated that some welded parts with surface cracking in the weld region had copper particles on the surface, and the question of copper contamination has been raised. With the aid of a scanning electron microscope and an electron microprobe, the existence of copper in an around the surface cracks has been verified. The copper is on the surface of the parts prior to welding in the form of small dust particles

World-sheet gauge fields in superstrings

International Nuclear Information System (INIS)

Porrati, M.; Tomboulis, E.T.

1989-01-01

We investigate the introduction of world-sheet 2-dimensional gauge fields in a manner consistent with world-sheet supersymmetry. We obtain the effective string action resulting from the exact integration over the world-sheet gauge fields to show that it generally describes string models with spontaneous breaking of gauge symmetries with continuous breaking parameters. We examine the question of spacetime supersymmetry spontaneous breaking, and show that breaking with continuous, in particular arbitrarily small breaking parameters does not occur; only breaking for discrete values of parameters is possible. (orig.)

Bifurcation of Jovian magnetotail current sheet

Directory of Open Access Journals (Sweden)

P. L. Israelevich

2006-07-01

Full Text Available Multiple crossings of the magnetotail current sheet by a single spacecraft give the possibility to distinguish between two types of electric current density distribution: single-peaked (Harris type current layer and double-peaked (bifurcated current sheet. Magnetic field measurements in the Jovian magnetic tail by Voyager-2 reveal bifurcation of the tail current sheet. The electric current density possesses a minimum at the point of the Bx-component reversal and two maxima at the distance where the magnetic field strength reaches 50% of its value in the tail lobe.

The reversal of fortunes: trends in county mortality and cross-county mortality disparities in the United States.

Directory of Open Access Journals (Sweden)

Majid Ezzati

2008-04-01

Full Text Available Counties are the smallest unit for which mortality data are routinely available, allowing consistent and comparable long-term analysis of trends in health disparities. Average life expectancy has steadily increased in the United States but there is limited information on long-term mortality trends in the US counties This study aimed to investigate trends in county mortality and cross-county mortality disparities, including the contributions of specific diseases to county level mortality trends.We used mortality statistics (from the National Center for Health Statistics [NCHS] and population (from the US Census to estimate sex-specific life expectancy for US counties for every year between 1961 and 1999. Data for analyses in subsequent years were not provided to us by the NCHS. We calculated different metrics of cross-county mortality disparity, and also grouped counties on the basis of whether their mortality changed favorably or unfavorably relative to the national average. We estimated the probability of death from specific diseases for counties with above- or below-average mortality performance. We simulated the effect of cross-county migration on each county's life expectancy using a time-based simulation model. Between 1961 and 1999, the standard deviation (SD of life expectancy across US counties was at its lowest in 1983, at 1.9 and 1.4 y for men and women, respectively. Cross-county life expectancy SD increased to 2.3 and 1.7 y in 1999. Between 1961 and 1983 no counties had a statistically significant increase in mortality; the major cause of mortality decline for both sexes was reduction in cardiovascular mortality. From 1983 to 1999, life expectancy declined significantly in 11 counties for men (by 1.3 y and in 180 counties for women (by 1.3 y; another 48 (men and 783 (women counties had nonsignificant life expectancy decline. Life expectancy decline in both sexes was caused by increased mortality from lung cancer, chronic obstructive

Estimated Colorado Golf Course Irrigation Water Use, 2005

Science.gov (United States)

Ivahnenko, Tamara

2009-01-01

Golf course irrigation water-use data were collected as part of the U.S. Geological Survey National Water Use Program's 2005 compilation to provide baseline information, as no golf course irrigation water-use data (separate from crop irrigation) have been reported in previous compilations. A Web-based survey, designed by the U.S. Geological Survey, in cooperation with the Rocky Mountain Golf Course Superintendents Association (RMGCSA), was electronically distributed by the association to the 237 members in Colorado. Forty-three percent of the members returned the survey, and additional source water information was collected by telephone for all but 20 of the 245 association member and non-member Colorado golf courses. For golf courses where no data were collected at all, an average 'per hole' coefficient, based on returned surveys from that same county, were applied. In counties where no data were collected at all, a State average 'per hole' value of 13.2 acre-feet was used as the coefficient. In 2005, Colorado had 243 turf golf courses (there are 2 sand courses in the State) that had an estimated 2.27 acre-feet per irrigated course acre, and 65 percent of the source water for these courses was surface water. Ground water, potable water (public supply), and reclaimed wastewater, either partially or wholly, were source waters for the remaining courses. Fifty-three of the 64 counties in Colorado have at least one golf course, with the greatest number of courses in Jefferson (23 courses), Arapahoe (22 courses), and El Paso Counties (20 courses). In 2005, an estimated 5,647.8 acre-feet in Jefferson County, 5,402 acre-feet in Arapahoe County, and 4,473.3 acre-feet in El Paso County were used to irrigate the turf grass.

Environmental constraints on West Antarctic ice-sheet formation

Energy Technology Data Exchange (ETDEWEB)

Lindstrom, D R; MacAyeal, D R

1987-01-01

Small perturbations in Antarctic environmental conditions can culminate in the demise of the Antarctic ice sheet's western sector. This may have happened during the last interglacial period, and could recur within the next millennium due to atmospheric warming from trace gas and CO/sub 2/ increases. In this study, we investigate the importance of sea-level, accumulation rate, and ice influx from the East Antarctic ice sheet in the re-establishment of the West Antarctic ice sheet from a thin cover using a time-dependent numerical ice-shelf model. Our results show that a precursor to the West Antarctic ice sheet can form within 3000 years. Sea-level lowering caused by ice-sheet development in the Northern Hemisphere has the greatest environmental influence. Under favorable conditions, ice grounding occurs over all parts of the West Antarctic ice sheet except up-stream of Thwaites Glacier and in the Ross Sea region.

Hydrothermal growth of upright-standing ZnO sheet microcrystals

International Nuclear Information System (INIS)

Shi, Ruixia; Yang, Ping; Dong, Xiaobin; Jia, Changchao; Li, Jia

2014-01-01

Highlights: • Upright-standing ZnO sheet microcrystals were hydrothermally fabricated. • The ZnO sheets were prepared with sodium oxalate at 70 °C without any surfactant. • The preferable adsorption of oxalate anions causes the formation of ZnO sheet. • The continuous growth in six directions leads to the formation of hexagonal sheets. - Abstract: Large-scale upright-standing ZnO sheet microcrystals were fabricated on Zn substrate using sodium oxalate as structure-directing agent by a hydrothermal method at low temperature (70 °C) without any surfactant. The sheets are about 3–5 μm in dimension and 100–300 nm in thickness. The strong and narrow diffraction peaks of ZnO indicate that the sample has a good crystallinity and size. The morphology of sheet-like ZnO varied with the concentrations of sodium oxalate and reaction time. The sheet-like ZnO would transform into rod-like ones when sodium oxalate was substituted by equivalent sodium acetate. The formation of sheet-like ZnO is attributed to the preferable adsorption of oxalate anions on (0 0 0 1) face of ZnO, which inhibits the intrinsic growth of ZnO. Additionally, the continuous growth in six (0 1 −1 0) directions that have the lowest surface energy leads to the formation of hexagonal sheets

12 CFR 615.5211 - Risk categories-balance sheet assets.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 6 2010-01-01 2010-01-01 false Risk categories-balance sheet assets. 615.5211...—balance sheet assets. Section 615.5210(c) specifies certain balance sheet assets that are not assigned to the risk categories set forth below. All other balance sheet assets are assigned to the percentage...

The plasma sheet boundary and Ksub(p)

International Nuclear Information System (INIS)

Freeman, J.W.

1975-01-01

Freeman and Maguire (1967) first drew attention to the intrusion of energetic plasma from the tail to the geostationary orbit during geomagnetically disturbed times. Vasyliunas (1968) reported a correlation between the inward extension of the inner boundary of the plasma sheet and the Ksub(p) index and pointed out that the plasma sheet could occasionally reach the geostationary orbit distance. More recently McIlwain (1972) using the more refined detectors aboard the ATS-5 geostationary space-craft, has emphasized the correlation between the location of the plasma sheet boundary along the ATS orbit and geomagnetic activity. Using some older but unpublished data from the Suprathermal Ion Detector aboard the ATS-1 geostationary satellite, the relation between the local time occurrence of the plasma sheet at the geostationary orbit (6.6Rsub(E)) and Ksub(p) index is reported and then a relationship for the shift in the plasma sheet radial position is derived. (Auth.)

Surface elevation changes of the greenland ice sheet - results from ESA'S ice sheet CCI

DEFF Research Database (Denmark)

Fredenslund Levinsen, Joanna; Khvorostovky, Kirill; Meister, Rakia

2013-01-01

In order to ensure long-term climate data records for the Greenland Ice Sheet (GIS), ESA have launched the Climate Change Initiative (CCI). This work presents the preliminary steps towards the Ice Sheet CCI's surface elevation change (SEC) derivation using radar altimeter data. In order to find...... the most optimal method, a Round Robin exercise was conducted in which the scientific community was asked to provide their best SEC estimate over the Jakobshavn Isbr drainage basin. The participants used both repeat-track (RT), overlapping footprints, and the cross-over (XO) methods, and both ICESat laser...... and Envisat radar altimeter data were used. Based on this and feedback sheets describing their methods we found that a combination of the RT and XO techniques yielded the best results. In the following, the obtained results will be presented and discussed....

Performance of a DC GaAs photocathode gun for the Jefferson lab FEL

CERN Document Server

Siggins, T; Bohn, C L; Bullard, D; Douglas, D; Grippo, A; Gubeli, J; Krafft, G A; Yunn, B

2001-01-01

The performance of the 320 kV DC photocathode gun has met the design specifications for the 1 kW IR Demo FEL at Jefferson Lab. This gun has shown the ability to deliver high average current beam with outstanding lifetimes. The GaAs photocathode has delivered 135 pC per bunch, at a bunch repetition rate of 37.425 MHz, corresponding to 5 mA average CW current. In a recent cathode lifetime measurement, 20 h of CW beam was delivered with an average current of 3.1 mA and 211 C of total charge from a 0.283 cm sup 2 illuminated spot. The cathode showed a 1/e lifetime of 58 h and a 1/e extracted charge lifetime of 618 C. We have achieved quantum efficiencies of 5% from a GaAs wafer that has been in service for 13 months delivering in excess 2400 C with only three activation cycles.

Probability based hydrologic catchments of the Greenland Ice Sheet

Science.gov (United States)

Hudson, B. D.

2015-12-01

Greenland Ice Sheet melt water impacts ice sheet flow dynamics, fjord and coastal circulation, and sediment and biogeochemical fluxes. Melt water exiting the ice sheet also is a key term in its mass balance. Because of this, knowledge of the area of the ice sheet that contributes melt water to a given outlet (its hydrologic catchment) is important to many ice sheet studies and is especially critical to methods using river runoff to assess ice sheet mass balance. Yet uncertainty in delineating ice sheet hydrologic catchments is a problem that is rarely acknowledged. Ice sheet catchments are delineated as a function of both basal and surface topography. While surface topography is well known, basal topography is less certain because it is dependent on radar surveys. Here, I a present a Monte Carlo based approach to delineating ice sheet catchments that quantifies the impact of uncertain basal topography. In this scheme, over many iterations I randomly vary the ice sheet bed elevation within published error bounds (using Morlighem et al., 2014 bed and bed error datasets). For each iteration of ice sheet bed elevation, I calculate the hydraulic potentiometric surface and route water over its path of 'steepest' descent to delineate the catchment. I then use all realizations of the catchment to arrive at a probability map of all major melt water outlets in Greenland. I often find that catchment size is uncertain, with small, random perturbations in basal topography leading to large variations in catchments size. While some catchments are well defined, others can double or halve in size within published basal topography error bars. While some uncertainty will likely always remain, this work points to locations where studies of ice sheet hydrology would be the most successful, allows reinterpretation of past results, and points to where future radar surveys would be most advantageous.

On the balance of stresses in the plasma sheet.

Science.gov (United States)

Rich, F. J.; Wolf, R. A.; Vasyliunas, V. M.

1972-01-01

The stress resulting from magnetic tension on the neutral sheet must, in a steady state, be balanced by any one or a combination of (1) a pressure gradient in the direction along the axis of the tail, (2) a similar gradient of plasma flow kinetic energy, and (3) the tension resulting from a pressure anisotropy within the plasma sheet. Stress balance in the first two cases requires that the ratios h/LX and BZ/BX be of the same order of magnitude, where h is the half-thickness of the neutral sheet, LX is the length scale for variations along the axis of the tail, and BZ and BX are the magnetic field components in the plasma sheet just outside the neutral sheet. The second case requires, in addition, that the plasma flow speed within the neutral sheet be of the order of or larger than the Alfven speed outside the neutral sheet. Stress balance in the third case requires that just outside the neutral sheet the plasma pressure obey the marginal firehose stability condition.

Thermal Transport Properties of Dry Spun Carbon Nanotube Sheets

Directory of Open Access Journals (Sweden)

Heath E. Misak

2016-01-01

Full Text Available The thermal properties of carbon nanotube- (CNT- sheet were explored and compared to copper in this study. The CNT-sheet was made from dry spinning CNTs into a nonwoven sheet. This nonwoven CNT-sheet has anisotropic properties in in-plane and out-of-plane directions. The in-plane direction has much higher thermal conductivity than the out-of-plane direction. The in-plane thermal conductivity was found by thermal flash analysis, and the out-of-plane thermal conductivity was found by a hot disk method. The thermal irradiative properties were examined and compared to thermal transport theory. The CNT-sheet was heated in the vacuum and the temperature was measured with an IR Camera. The heat flux of CNT-sheet was compared to that of copper, and it was found that the CNT-sheet has significantly higher specific heat transfer properties compared to those of copper. CNT-sheet is a potential candidate to replace copper in thermal transport applications where weight is a primary concern such as in the automobile, aircraft, and space industries.

Development of Micromegas detectors for the CLAS12 experiment at Jefferson Laboratory

CERN Document Server

Charles, Gabriel

This thesis presents my work performed since 2010 to develop Micromegas detectors for the CLAS12 spectrometer that will be installed in the Hall B of Jefferson Laboratory (USA). The Micromegas are robust, fast and cheap gaseous detectors. Nevertheless, they must be adapted to the specific CLAS12 environment as there are many challenges to face : presence of a strong magnetic field, off-detector frontend electronics, high hadrons rate, necessity to curve the detectors, few space available. My PhD started by beam tests at CERN that allowed to evaluate the spark rate in CLAS12 Micromegas at a few Hertz. An important part of this document is therefore devoted to the study of several innovative methods to minimize the dead time induced by sparks. Thus, I have performed intensive tests on the optimization of the micromesh high voltage filter, with on Micromegas equipped with a GEM foild or on resistive Micromegas. The latter giving excellent results, full scale prototypes, one of which built by a company, have been...

Polarized positrons in Jefferson lab electron ion collider (JLEIC)

Science.gov (United States)

Lin, Fanglei; Grames, Joe; Guo, Jiquan; Morozov, Vasiliy; Zhang, Yuhong

2018-05-01

The Jefferson Lab Electron Ion Collider (JLEIC) is designed to provide collisions of electron and ion beams with high luminosity and high polarization to reach new frontier in exploration of nuclear structure. The luminosity, exceeding 1033 cm-2s-1 in a broad range of the center-of-mass (CM) energy and maximum luminosity above 1034 cm-2s-1, is achieved by high-rate collisions of short small-emittance low-charge bunches with proper cooling of the ion beam and synchrotron radiation damping of the electron beam. The polarization of light ion species (p, d, 3He) and electron can be easily preserved, manipulated and maintained by taking advantage of the unique figure-8 shape rings. With a growing physics interest, polarized positron-ion collisions are considered to be carried out in the JLEIC to offer an additional probe to study the substructure of nucleons and nuclei. However, the creation of polarized positrons with sufficient intensity is particularly challenging. We propose a dedicated scheme to generate polarized positrons. Rather than trying to accumulate "hot" positrons after conversion, we will accumulate "cold" electrons before conversion. Charge accumulation additionally provides a novel means to convert high repetition rate (>100 MHz) electron beam from the gun to a low repetition rate (<100 MHz) positron beam for broad applications. In this paper, we will address the scheme, provide preliminary estimated parameters and explain the key areas to reach the desired goal.

Somerset County Renewable Energy Initiative

Energy Technology Data Exchange (ETDEWEB)

Katula, Denise [County of Somerset, Somervile, NJ (United States)

2014-05-07

The County of Somerset, New Jersey, through the Somerset County Improvement Authority (SCIA), applied Federal funding through the U.S. Department of Energy to will apply project funds to buy-down the capital costs of equipment associated with the installation of solar photovoltaic (PV) systems at two sites owned by the County. This Renewable Energy Initiative allows the County to take advantage of clean renewable energy, without any adverse debt impacts, and at a price that results in operating budget savings beyond what is presently available in the marketplace. This project addressed the objectives of the Office of Energy Efficiency and Renewable Energy by making the acquisition of renewable energy more affordable for the County, thereby, encouraging other counties and local units to develop similar programs and increase the deployment of solar energy technologies. The two sites that were funded by the DOE grant are part of a much larger, ambitious, and unique renewable energy project, described in the next section.

Nonparaxial Bessel and Bessel–Gauss pincers light-sheets

Energy Technology Data Exchange (ETDEWEB)

Mitri, F.G., E-mail: F.G.Mitri@ieee.org

2017-01-23

Highlights: • Bessel and Bessel–Gauss autofocusing light sheets (i.e. beams in 2D) are developed. • The light-sheets are synthesized based on the angular spectrum decomposition method. • Computations of the scattering, radiation force and torque benefit from the solutions. - Abstract: Nonparaxial optical Bessel and Bessel–Gauss pincers optical-sheets are introduced based upon the angular spectrum decomposition in plane waves. The angular spectrum function and the beam-shape coefficients are expressed by means of improper integrals computed numerically. The radiated component of the electric field is also evaluated, displaying unique features of the nonparaxial Bessel pincers light-sheets. This new type of auto-focusing light-sheets finds potential applications in the development of novel methods in optical light-sheet tweezers for particle manipulation in opto-fluidics, particle sizing and imaging. Numerical predictions for the scattering, radiation force and torque, and particle dynamics also benefit from the developed beam solution.

Nonparaxial Bessel and Bessel–Gauss pincers light-sheets

International Nuclear Information System (INIS)

Mitri, F.G.

2017-01-01

Highlights: • Bessel and Bessel–Gauss autofocusing light sheets (i.e. beams in 2D) are developed. • The light-sheets are synthesized based on the angular spectrum decomposition method. • Computations of the scattering, radiation force and torque benefit from the solutions. - Abstract: Nonparaxial optical Bessel and Bessel–Gauss pincers optical-sheets are introduced based upon the angular spectrum decomposition in plane waves. The angular spectrum function and the beam-shape coefficients are expressed by means of improper integrals computed numerically. The radiated component of the electric field is also evaluated, displaying unique features of the nonparaxial Bessel pincers light-sheets. This new type of auto-focusing light-sheets finds potential applications in the development of novel methods in optical light-sheet tweezers for particle manipulation in opto-fluidics, particle sizing and imaging. Numerical predictions for the scattering, radiation force and torque, and particle dynamics also benefit from the developed beam solution.

Current status of Enterobius vermicularis infection in primary schoolchildren in Miaoli County and Taichung County, Taiwan.

Science.gov (United States)

Wang, Cheng-Chieh; Lee, Yuan-Fang; Chang, Chih-Cheng; Lee, Nie-Sue; Chen, Po-Yen; Huang, Fang-Liang; Liou, Nuo-Wei

2009-10-01

No epidemiological survey of the prevalence of Enterobius vermicularis infection in Miaoli County and Taichung County has been conducted. This epidemiological survey was performed to describe the profile of E. vermicularis infection in schoolchildren in Miaoli County and Taichung County. The first part of this study was conducted between November 2005 and February 2006 in Miaoli County. 44,071 primary schoolchildren from 18 districts were examined by 2 consecutive-day adhesive cellophane perianal swabs to estimate the infection rate. The second part was performed between October 2006 and January 2007 in Taichung County. 24,382 primary schoolchildren from 14 districts were examined. In Miaoli County, the infection rate was 2.39% (1054/44,071). The infection rate was highest in the Taian (6.69%; 20/299), Shytarn (4.49%; 11/245), and Dahu townships (3.6%; 40/1111). In Taichung County, the infection rate was 2.95% (720/24,382). The infection rate was highest in the Da-an (5.46%; 26/476) and Heping townships (4.48%; 9/201). The infection rate for a family with > or =3 children was significantly higher than that for a family with pinworm infection among the groups surveyed.

Bifurcation of Jovian magnetotail current sheet

Directory of Open Access Journals (Sweden)

P. L. Israelevich

2006-07-01

Full Text Available Multiple crossings of the magnetotail current sheet by a single spacecraft give the possibility to distinguish between two types of electric current density distribution: single-peaked (Harris type current layer and double-peaked (bifurcated current sheet. Magnetic field measurements in the Jovian magnetic tail by Voyager-2 reveal bifurcation of the tail current sheet. The electric current density possesses a minimum at the point of the B_x-component reversal and two maxima at the distance where the magnetic field strength reaches 50% of its value in the tail lobe.

Buckling Behavior of Substrate Supported Graphene Sheets

Directory of Open Access Journals (Sweden)

Kuijian Yang

2016-01-01

Full Text Available The buckling of graphene sheets on substrates can significantly degrade their performance in materials and devices. Therefore, a systematic investigation on the buckling behavior of monolayer graphene sheet/substrate systems is carried out in this paper by both molecular mechanics simulations and theoretical analysis. From 70 simulation cases of simple-supported graphene sheets with different sizes under uniaxial compression, two different buckling modes are investigated and revealed to be dominated by the graphene size. Especially, for graphene sheets with length larger than 3 nm and width larger than 1.1 nm, the buckling mode depends only on the length/width ratio. Besides, it is revealed that the existence of graphene substrate can increase the critical buckling stress and strain to 4.39 N/m and 1.58%, respectively, which are about 10 times those for free-standing graphene sheets. Moreover, for graphene sheets with common size (longer than 20 nm, both theoretical and simulation results show that the critical buckling stress and strain are dominated only by the adhesive interactions with substrate and independent of the graphene size. Results in this work provide valuable insight and guidelines for the design and application of graphene-derived materials and nano-electromechanical systems.

77 FR 11573 - Notice of Inventory Completion: History Colorado, Denver, CO

Science.gov (United States)

2012-02-27

... during a drug raid in Jefferson County, CO. The origin of the remains is unknown. The remains were turned... Charney, a former professor at the University, who died in 1998. The human remains were subsequently taken... objects originating from inadvertent discoveries on Colorado state and private lands. As a result of the...

Timber resource statistics for nonnational forest land in western Washington, 2001.

Science.gov (United States)

Andrew N. Gray; Charles F. Veneklase; Robert D. Rhoads

2005-01-01

This report is a summary of timber resource statistics for an inventory of the 19 counties in western Washington: Clallam, Clark, Cowlitz, Grays Harbor, Island, Jefferson, King, Kitsap, Lewis, Mason, Pacific, Pierce, San Juan, Skagit, Skamania, Snohomish, Thurston, Wahkiakum, and Whatcom. The inventory in 2000 sampled all private and public lands except those...

78 FR 26319 - Deepwater Horizon Oil Spill; Proposal of Future Early Restoration Projects and Environmental Reviews

Science.gov (United States)

2013-05-06

... selected and implemented in accordance with the Oil Pollution Act of 1990 (OPA), the Framework Agreement... oil spill under the Oil Pollution Act 1990 (OPA; 33 U.S.C. 2701 et seq.). Pursuant to OPA, federal and... cost of this project is approximately $3.5 million. Sea Rim State Park Amenities (Jefferson County...

Asset Management Plan: 1998-2003.

Science.gov (United States)

Jefferson County School District R-1, Denver, CO.

The Jefferson County School District (Denver, Colorado) presents its final scheduling and funding source information for the 1998-2003 capital improvement program and the status of the 1992-1997 completed capital improvement project costs compared to the budget. Funding data are detailed for each of the district's 182 public schools, special use…

Comparisons of American, Israeli, Italian and Mexican physicians and nurses on the total and factor scores of the Jefferson scale of attitudes toward physician-nurse collaborative relationships.

Science.gov (United States)

Hojat, Mohammadreza; Gonnella, Joseph S; Nasca, Thomas J; Fields, Sylvia K; Cicchetti, Americo; Lo Scalzo, Alessandra; Taroni, Francesco; Amicosante, Anna Maria Vincenza; Macinati, Manuela; Tangucci, Massimo; Liva, Carlo; Ricciardi, Gualtiero; Eidelman, Shmuel; Admi, Hanna; Geva, Hana; Mashiach, Tanya; Alroy, Gideon; Alcorta-Gonzalez, Adelina; Ibarra, David; Torres-Ruiz, Antonio

2003-05-01

This cross-cultural study was designed to compare the attitudes of physicians and nurses toward physician-nurse collaboration in the United States, Israel, Italy and Mexico. Total participants were 2522 physicians and nurses who completed the Jefferson Scale of Attitudes Toward Physician-Nurse Collaboration (15 Likert-type items, (Hojat et al., Evaluation and the Health Professions 22 (1999a) 208; Nursing Research 50 (2001) 123). They were compared on the total scores and four factors of the Jefferson Scale (shared education and team work, caring as opposed to curing, nurses, autonomy, physicians' dominance). Results showed inter- and intra-cultural similarities and differences among the study groups providing support for the social role theory (Hardy and Conway, Role Theory: Perspectives for Health Professionals, Appelton-Century-Crofts, New York, 1978) and the principle of least interest (Waller and Hill, The Family: A Dynamic Interpretation, Dryden, New York, 1951) in inter-professional relationships. Implications for promoting physician-nurse education and inter-professional collaboration are discussed.

Census County Subdivisions for the United States Virgin Islands (CENSUS.COUNTY_SUBDIV_USVI)

Data.gov (United States)

U.S. Environmental Protection Agency — County subdivisions are the primary divisions of counties and statistically equivalent entities for the reporting of decennial census data. They include census...

The 2016 groundwater flow model for Dane County, Wisconsin

Science.gov (United States)

Parsen, Michael J.; Bradbury, Kenneth R.; Hunt, Randall J.; Feinstein, Daniel T.

2016-01-01

the Yahara River valley and in northeastern Dane County. Layer 12 represents the Mount Simon sandstone as the lowermost model layer. It directly overlies the Precambrian crystalline basement rock, whose top surface forms the lower boundary of the model. The model uses the USGS MODFLOW-NWT finite-difference code, a standalone version of MODFLOW-2005 that incorporates the Newton (NWT) solver. MODFLOW-NWT improves the handling of unconfined conditions by smoothing the transition from wet to dry cells. The model explicitly simulates groundwater–surface-water interaction with streamflow routing and lake-level fluctuation. Model input included published and unpublished hydrogeologic data from recent estimates of aquifer hydraulic conductivities. A spatial groundwater recharge distribution was obtained from a recent GIS-based, soil-water-balance model for Dane County. Groundwater withdrawals from pumping were simulated for 572 wells across the entire model domain, which includes Dane County and portions of seven neighboring counties—Columbia, Dodge, Green, Iowa, Jefferson, Lafayette, and Rock. These wells withdrew an average of 60 million gallons per day (mgd) over the 5-year period from 2006 through 2010. Within Dane County, 385 wells were simulated with an average withdrawal rate of 52 mgd.Model calibration used the parameter estimation code PEST, and calibration targets included heads, stream and spring flows, lake levels, and borehole flows. Steady-state calibration focused on the period 2006 through 2010; the transient calibration focused on the 7-week drought period from late May through July 2012. This model represents a significant step forward from previous work because of its finer grid resolution, improved hydrostratigraphic discretization, transient capabilities, and more sophisticated representation of surface-water features and multi-aquifer wells.Potential applications of the model include evaluation of potential sites for and impacts of new high

Lateral dimension-dependent antibacterial activity of graphene oxide sheets.

Science.gov (United States)

Liu, Shaobin; Hu, Ming; Zeng, Tingying Helen; Wu, Ran; Jiang, Rongrong; Wei, Jun; Wang, Liang; Kong, Jing; Chen, Yuan

2012-08-21

Graphene oxide (GO) is a promising precursor to produce graphene-family nanomaterials for various applications. Their potential health and environmental impacts need a good understanding of their cellular interactions. Many factors may influence their biological interactions with cells, and the lateral dimension of GO sheets is one of the most relevant material properties. In this study, a model bacterium, Escherichia coli ( E. coli ), was used to evaluate the antibacterial activity of well-dispersed GO sheets, whose lateral size differs by more than 100 times. Our results show that the antibacterial activity of GO sheets toward E. coli cells is lateral size dependent. Larger GO sheets show stronger antibacterial activity than do smaller ones, and they have different time- and concentration-dependent antibacterial activities. Large GO sheets lead to most cell loss after 1 h incubation, and their concentration strongly influences antibacterial activity at relative low concentration (oxidation capacity toward glutathione is similar, consistent with X-ray photoelectron spectroscopy and ultraviolet-visible absorption spectroscopy results. This suggests the lateral size-dependent antibacterial activity of GO sheets is caused by neither their aggregation states, nor oxidation capacity. Atomic force microscope analysis of GO sheets and cells shows that GO sheets interact strongly with cells. Large GO sheets more easily cover cells, and cells cannot proliferate once fully covered, resulting in the cell viability loss observed in the followed colony counting test. In contrast, small GO sheets adhere to the bacterial surfaces, which cannot effectively isolate cells from environment. This study highlights the importance of tailoring the lateral dimension of GO sheets to optimize the application potential with minimal risks for environmental health and safety.

Fabrication of Carbon Nanotube Polymer Actuator Using Nanofiber Sheet

Science.gov (United States)

Kato, Hayato; Shimizu, Akikazu; Sato, Taiga; Kushida, Masahito

2017-11-01

Carbon nanotube polymer actuators were developed using composite nanofiber sheets fabricated by multi-walled carbon nanotubes(MWCNTs) and poly (vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP). Nanofiber sheets were fabricated by electrospinning method. The effect of flow rate and polymer concentration on nanofiber formation were verified for optimum condition for fabricating nanofiber sheets. We examined the properties of MWCNT/PVDF-HFP nanofiber sheets, as follows. Electrical conductivity and mechanical strength increased as the MWCNT weight ratio increased. We fabricated carbon nanotube polymer actuators using MWCNT/PVDF-HFP nanofiber sheets and succeeded in operating of our actuators.

Global ice sheet/RSL simulations using the higher-order Ice Sheet System Model.

Science.gov (United States)

Larour, E. Y.; Ivins, E. R.; Adhikari, S.; Schlegel, N.; Seroussi, H. L.; Morlighem, M.

2017-12-01

Relative sea-level rise is driven by processes that are intimately linked to the evolution ofglacial areas and ice sheets in particular. So far, most Earth System models capable of projecting theevolution of RSL on decadal to centennial time scales have relied on offline interactions between RSL andice sheets. In particular, grounding line and calving front dynamics have not been modeled in a way that istightly coupled with Elasto-Static Adjustment (ESA) and/or Glacial-Isostatic Adjustment (GIA). Here, we presenta new simulation of the entire Earth System in which both Greenland and Antarctica ice sheets are tightly coupledto an RSL model that includes both ESA and GIA at resolutions and time scales compatible with processes suchas grounding line dynamics for Antarctica ice shelves and calving front dynamics for Greenland marine-terminatingglaciers. The simulations rely on the Ice Sheet System Model (ISSM) and show the impact of higher-orderice flow dynamics and coupling feedbacks between ice flow and RSL. We quantify the exact impact of ESA andGIA inclusion on grounding line evolution for large ice shelves such as the Ronne and Ross ice shelves, as well asthe Agasea Embayment ice streams, and demonstate how offline vs online RSL simulations diverge in the long run,and the consequences for predictions of sea-level rise.This work was performed at the California Institute of Technology's Jet Propulsion Laboratory undera contract with the National Aeronautics and Space Administration's Cryosphere Science Program.

Allegheny County Property Assessments

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — Real Property parcel characteristics for Allegheny County, PA. Includes information pertaining to land, values, sales, abatements, and building characteristics (if...

Coupling of climate models and ice sheet models by surface mass balance gradients: application to the Greenland Ice Sheet

Directory of Open Access Journals (Sweden)

M. M. Helsen

2012-03-01

Full Text Available It is notoriously difficult to couple surface mass balance (SMB results from climate models to the changing geometry of an ice sheet model. This problem is traditionally avoided by using only accumulation from a climate model, and parameterizing the meltwater run-off as a function of temperature, which is often related to surface elevation (H_s. In this study, we propose a new strategy to calculate SMB, to allow a direct adjustment of SMB to a change in ice sheet topography and/or a change in climate forcing. This method is based on elevational gradients in the SMB field as computed by a regional climate model. Separate linear relations are derived for ablation and accumulation, using pairs of H_s and SMB within a minimum search radius. The continuously adjusting SMB forcing is consistent with climate model forcing fields, also for initially non-glaciated areas in the peripheral areas of an ice sheet. When applied to an asynchronous coupled ice sheet – climate model setup, this method circumvents traditional temperature lapse rate assumptions. Here we apply it to the Greenland Ice Sheet (GrIS. Experiments using both steady-state forcing and glacial-interglacial forcing result in realistic ice sheet reconstructions.

Northeast Florida Regional Sediment Management: Implementation Strategies and Recommendations for Nassau County and Duval County, Florida

Science.gov (United States)

2016-03-01

management strategies and alternatives are actively coordinated. DISCLAIMER: The contents of this report are not to be used for advertising , publication... Strategies and Recommendations for Nassau County and Duval County, Florida Co as ta l a nd H yd ra ul ic s La bo ra to ry Kevin C. Hodgens, Michael...Sediment Management Implementation Strategies and Recommendations for Nassau County and Duval County, Florida Kevin C. Hodgens and Michael P

Joining of Aluminium Alloy Sheets by Rectangular Mechanical Clinching

International Nuclear Information System (INIS)

Abe, Y.; Mori, K.; Kato, T.

2011-01-01

A mechanical clinching has the advantage of low running costs. However, the joint strength is not high. To improve the maximum load of the joined sheets by a mechanical clinching, square and rectangular mechanical clinching were introduced. In the mechanical clinching, the two sheets are mechanically joined by forming an interlock between the lower and upper sheets by the punch and die. The joined length with the interlock was increased by the rectangular punch and die. The deforming behaviours of the sheets in the mechanical clinching were investigated, and then the interlock in the sheets had distribution in the circumference of the projection. Although the interlocks were formed in both projection side and diagonal, the interlock in the diagonal was smaller because of the long contact length between the lower sheet and the die cavity surface. The maximum load of the joined sheets by the rectangular mechanical clinching was two times larger than the load by the round mechanical clinching.

DIGITAL FLOOD INSURANCE RATE MAP DATABASE, JEFFERSON COUNTY, IDAHO, USA

Data.gov (United States)

Federal Emergency Management Agency, Department of Homeland Security — The Digital Flood Insurance Rate Map (DFIRM) Database depicts flood risk information and supporting data used to develop the risk data. The primary risk...

The properties of bioengineered chondrocyte sheets for cartilage regeneration

Directory of Open Access Journals (Sweden)

Ota Naoshi

2009-03-01

Full Text Available Abstract Background Although the clinical results of autologous chondrocyte implantation for articular cartilage defects have recently improved as a result of advanced techniques based on tissue engineering procedures, problems with cell handling and scaffold imperfections remain to be solved. A new cell-sheet technique has been developed, and is potentially able to overcome these obstacles. Chondrocyte sheets applicable to cartilage regeneration can be prepared with this cell-sheet technique using temperature-responsive culture dishes. However, for clinical application, it is necessary to evaluate the characteristics of the cells in these sheets and to identify their similarities to naive cartilage. Results The expression of SOX 9, collagen type 2, 27, integrin α10, and fibronectin genes in triple-layered chondrocyte sheets was significantly increased in comparison to those in conventional monolayer culture and in a single chondrocyte sheet, implying a nature similar to ordinary cartilage. In addition, immunohistochemistry demonstrated that collagen type II, fibronectin, and integrin α10 were present in the triple-layered chondrocyte sheets. Conclusion The results of this study indicate that these chondrocyte sheets with a consistent cartilaginous phenotype and adhesive properties may lead to a new strategy for cartilage regeneration.

75 FR 26709 - Clarke County Water Supply Project, Clarke County, IA

Science.gov (United States)

2010-05-12

... Project, Clarke County, IA AGENCY: Natural Resources Conservation Service. ACTION: Notice of intent to... Conservationist for Planning, 210 Walnut Street, Room 693, Des Moines, IA 50309-2180, telephone: 515-284- 4769... available at the Iowa NRCS Web site at http://www.ia.nrcs.usda.gov . A map of the Clarke County Water Supply...

Allegheny County Parcel Boundaries

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — This dataset contains parcel boundaries attributed with county block and lot number. Use the Property Information Extractor for more control downloading a filtered...

Allegheny County Anxiety Medication

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — These Census Tract-level datasets described here provide de-identified diagnosis data for customers of three managed care organizations in Allegheny County (Gateway...

Allegheny County Depression Medication

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — These Census Tract-level datasets described here provide de-identified diagnosis data for customers of three managed care organizations in Allegheny County (Gateway...

Allegheny County Crash Data

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — Contains locations and information about every crash incident reported to the police in Allegheny County from 2004 to 2016. Fields include injury severity,...

Allegheny County Crash Data

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — Contains locations and information about every crash incident reported to the police in Allegheny County from 2004 to 2017. Fields include injury severity,...

Fatigue characteristics of dual-phase steel sheets

Energy Technology Data Exchange (ETDEWEB)

Onn, Irwan Herman; Ahmad, Norhayati; Tamin, Mohd Nasir [Universiti Teknologi Malaysia, Skudai (Malaysia)

2015-01-15

Fatigue characteristics of dual-phase steel sheets, commonly used in automobile body construction were established. For this purpose, a series of fatigue tests, each at constant stress amplitude were conducted on 1.2 mm-thick, dual-phase DP600 steel sheet specimens with two different load ratios of minimum-to-maximum stress, R = 0.1 and -1. The resulting fatigue behavior is expressed in terms of fatigue strength-life (S-N) curves. Fatigue behavior of the steel sheets in the high-cycle fatigue region can be represented by Basquin's equation with coefficient and exponent value of 921.2 and 0.093, respectively. An endurance limit of 255 MPa is observed. In addition, fatigue strengths of the dual-phase steel sheets display lower magnitude than their bulk counterparts. Effect of mean stress on fatigue behavior of the steel sheets is well predicted by Walker's model. Exponential calibration factor is introduced to the models by SWT, Goodman and Morrow with comparable prediction to the Walker's model.

Recent Measurements from the G0 Parity Violation Experiment Carried out at Jefferson Laboratory

International Nuclear Information System (INIS)

Bimbot, L.

2008-01-01

The measurements were made at the Thomas Jefferson National Accelerator Facility (J Lab.), Newport News, V A (USA) in the backward angle configuration set-up. A toroidal spectrometer, associated with particle detectors, is used to count electrons and pions from a liquid hydrogen or deuterium target. Parity-violating than the former one by orders of magnitude and requires special techniques to be observed and isolated. Parity violation is specific to the electro-weak interaction and forms the basis asymmetries in elastic electron-proton scattering are determined for momentum transfers of Q 2 = 0.62 and 0.23 (GeV/c) 2 . Combined with previous results obtained with the forward angle configuration setup, these measurements give access to the separation of the values of electric and magnetic strange form factors of the proton. More results may be extracted from the asymmetries for inelastically scattered electrons and for produced pions

Dynamics of a radially expanding liquid sheet: Experiments

Science.gov (United States)

Majumdar, Nayanika; Tirumkudulu, Mahesh

2017-11-01

A recent theory predicts that sinuous waves generated at the center of a radially expanding liquid sheet grow spatially even in absence of a surrounding gas phase. Unlike flat liquid sheets, the thickness of a radially expanding liquid sheet varies inversely with distance from the center of the sheet. To test the predictions of the theory, experiments were carried out on a horizontal, radially expanding liquid sheet formed by collision of a single jet on a solid impactor. The latter was placed on a speaker-vibrator with controlled amplitude and frequency. The growth of sinuous waves was determined by measuring the wave surface inclination angle using reflected laser light under both atmospheric and sub-atmospheric pressure conditions. It is shown that the measured growth rate matches with the predictions of the theory over a large range of Weber numbers for both pressure conditions suggesting that the thinning of the liquid sheet plays a dominant role in setting the growth rate of sinuous waves with minimal influence of the surrounding gas phase on its dynamics. IIT Bombay.

Allegheny County Tobacco Vendors

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — The tobacco vendor information provides the location of all tobacco vendors in Allegheny County in 2015. Data was compiled from administrative records managed by...

Allegheny County Street Centerlines

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — This dataset contains the locations of the street centerlines for vehicular and foot traffic in Allegheny County. Street Centerlines are classified as Primary Road,...

Allegheny County Major Rivers

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — This dataset contains locations of major rivers that flow through Allegheny County. These shapes have been taken from the Hydrology dataset. The Ohio River,...

Allegheny County Traffic Counts

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — Traffic sensors at over 1,200 locations in Allegheny County collect vehicle counts for the Pennsylvania Department of Transportation. Data included in the Health...

Optimal swimming of a sheet.

Science.gov (United States)

Montenegro-Johnson, Thomas D; Lauga, Eric

2014-06-01

Propulsion at microscopic scales is often achieved through propagating traveling waves along hairlike organelles called flagella. Taylor's two-dimensional swimming sheet model is frequently used to provide insight into problems of flagellar propulsion. We derive numerically the large-amplitude wave form of the two-dimensional swimming sheet that yields optimum hydrodynamic efficiency: the ratio of the squared swimming speed to the rate-of-working of the sheet against the fluid. Using the boundary element method, we show that the optimal wave form is a front-back symmetric regularized cusp that is 25% more efficient than the optimal sine wave. This optimal two-dimensional shape is smooth, qualitatively different from the kinked form of Lighthill's optimal three-dimensional flagellum, not predicted by small-amplitude theory, and different from the smooth circular-arc-like shape of active elastic filaments.

Balance of the West Antarctic Ice Sheet

Science.gov (United States)

2002-01-01

For several decades, measurements of the West Antarctic Ice Sheet showed it to be retreating rapidly. But new data derived from satellite-borne radar sensors show the ice sheet to be growing. Changing Antarctic ice sheets remains an area of high scientific interest, particularly in light of recent global warming concerns. These new findings are significant because scientists estimate that sea level would rise 5-6 meters (16-20 feet) if the ice sheet collapsed into the sea. Do these new measurements signal the end of the ice sheet's 10,000-year retreat? Or, are these new satellite data simply much more accurate than the sparse ice core and surface measurements that produced the previous estimates? Another possibility is that the ice accumulation may simply indicate that the ice sheet naturally expands and retreats in regular cycles. Cryologists will grapple with these questions, and many others, as they examine the new data. The image above depicts the region of West Antarctica where scientists measured ice speed. The fast-moving central ice streams are shown in red. Slower tributaries feeding the ice streams are shown in blue. Green areas depict slow-moving, stable areas. Thick black lines depict the areas that collect snowfall to feed their respective ice streams. Reference: Ian Joughin and Slawek Tulaczyk Science Jan 18 2002: 476-480. Image courtesy RADARSAT Antarctic Mapping Project

Spina Bifida: General Information. Fact Sheet Number 12 = La Espina Bifida: Informacion General. Fact Sheet Number 12.

Science.gov (United States)

National Information Center for Children and Youth with Disabilities, Washington, DC.

This fact sheet offers definitions of the three types of spina bifida, outlines their incidence, describes characteristics of individuals with spina bifida, and reviews educational implications. The fact sheet emphasizes that school programs should be flexible to accommodate these students' special needs and frequent absences, that children with…

County and Parish Boundaries, This was created and maintained by Johnson County Records and Tax Administration and is updated when changes occur to county boundaries, Published in 2007, Johnson County Government.

Data.gov (United States)

NSGIC Local Govt | GIS Inventory — County and Parish Boundaries dataset current as of 2007. This was created and maintained by Johnson County Records and Tax Administration and is updated when changes...

Investigating the psychometric properties of the Jefferson Scale of Physician Empathy in a sample of Malaysian medical students

Directory of Open Access Journals (Sweden)

Spasenoska M

2016-06-01

Full Text Available Marija Spasenoska,1 Shane Costello,1 Brett Williams2 1Faculty of Education, 2Department of Community Emergency Health and Paramedic Practice, Monash University, Melbourne, VIC, Australia Objective: The purpose of this present study was to investigate the psychometric properties of the Jefferson Scale of Physician Empathy – student version (JSPE-S. Subjects and methods: This study recruited 193 Malaysian medical students enrolled in year one and year two studies. A principal-component analysis with Varimax rotation was conducted. Procrustes rotation was used to confirm the item to model fit, which allows for a comparison of actual structure against an ideal hypothesized structure. Items were systematically removed based on low communalities of < 0.3 and poor loading of items onto components. Results: A two-component solution was found, comprised of “perspective taking” and “compassionate care”. Following item removal, eleven items remained. A Procrustes analysis revealed that this eleven-item measure demonstrated an excellent model fit. A possible third component was identified, though is not recommended for use, due to construct underrepresentation. Conclusion: This study found the Jefferson Scale of Physician Empathy fitted best to a two-component model using eleven items. Item, component, and overall congruence were very high, and scale reliabilities were adequate. The results of this study suggest that the eleven-item, two-component solution demonstrates excellent psychometric properties and structural validity in a Malaysian medical student population. Future research could consider using the short eleven-item measure in both student and health care profession samples to investigate the role of empathy in health care. Keywords: empathy, medical students, psychometrics

Ice Sheets & Ice Cores

DEFF Research Database (Denmark)

Mikkelsen, Troels Bøgeholm

Since the discovery of the Ice Ages it has been evident that Earth’s climate is liable to undergo dramatic changes. The previous climatic period known as the Last Glacial saw large oscillations in the extent of ice sheets covering the Northern hemisphere. Understanding these oscillations known....... The first part concerns time series analysis of ice core data obtained from the Greenland Ice Sheet. We analyze parts of the time series where DO-events occur using the so-called transfer operator and compare the results with time series from a simple model capable of switching by either undergoing...

Influence of Peer Pressure on Secondary School Students Drop out in Rongo Sub-County, Migori County, Kenya

Science.gov (United States)

Omollo, Atieno Evaline; Yambo, Onyango J. M.

2017-01-01

The purpose of this study was to establish the influence of peer pressure on secondary school students' drop out in Rongo Sub-County, Migori County, Kenya. The statement of the problem showed that the sub-county had a dropout rate of 43 percent as compared to the neighboring sub counties like Uriri, Awendo, Nyatike, Kuria and Migori which had 25,…

Microstructure evolution of a dissimilar junction interface between an Al sheet and a Ni-coated Cu sheet joined by magnetic pulse welding

Energy Technology Data Exchange (ETDEWEB)

Itoi, Takaomi, E-mail: itoi@faculty.chiba-u.jp [Department of Mechanical Engineering, Chiba University, 1-33, Yayoi-cho, Inage-ku, Chiba 263-8522 (Japan); Mohamad, Azizan Bin; Suzuki, Ryo [Department of Mechanical Engineering, Chiba University, 1-33, Yayoi-cho, Inage-ku, Chiba 263-8522 (Japan); Okagawa, Keigo [Department of Electrical and Electronics Engineering, Tokyo Metropolitan College of Industrial Technology, 1-10-40 Higashi ohi, Shinagawa-ku, Tokyo 140-0011 (Japan)

2016-08-15

An Al sheet and a Ni-coated Cu sheet were lap joined by using magnetic pulse welding (MPW). Tensile tests were performed on the joined sheets, and a good lap joint was achieved at a discharge energy of > 0.9 kJ. The weld interface exhibited a wavy morphology and an intermediate layer along the weld interface. Microstructure observations of the intermediate layer revealed that the Ni coating region consisted of a Ni–Al binary amorphous alloy and that the Al sheet region contained very fine Al nanograins. Ni fragments indicative of unmelted residual Ni from the coating were also observed in parts of the intermediate layer. Formation of these features can be attributed to localize melting and a subsequent high rate cooling of molten Al and Ni confined to the interface during the MPW process. In the absence of an oxide film, atomic-scale bonding was also achieved between the intermediate layer and the sheet surfaces after the collision. MPW utilises impact energy, which affects the sheet surfaces. From the obtained results, good lap joint is attributed to an increased contact area, the anchor effect, work hardening, the absence of an oxide film, and suppressed formation of intermetallic compounds at the interface. - Highlights: •Good lap joint of an Al sheet and a Ni-coated Cu sheet was achieved by using magnetic pulse welding. •A Ni–Al binary amorphous alloy was formed as an intermediate layer at weld interface. •Atomic-scale bonding was achieved between the intermediate layer and the sheet surfaces.

Dorothy Davison (1890-1984): Manchester medical artist and her work for neurosurgeon Sir Geoffrey Jefferson (1886-1961).

Science.gov (United States)

Mohr, Peter D

2017-05-01

Miss Davison was a medical artist at the Manchester Royal Infirmary and the University of Manchester from around 1918 until her retirement in 1957. She illustrated books and scientific papers on anthropology, anatomy and surgery, and became well known for her striking pictures produced by the 'Ross board technique'- a difficult process that she helped pioneer from the 1930s and which forms the bulk of the work she undertook for neurosurgeon Geoffrey Jefferson during the 1930s-1950s. His Neurosurgical Department became the main base for her work until his retirement in 1953. She was an active member of the Medical Artist Association (MAA) which she helped found in 1949.

Synthesis of nanometre-thick MoO3 sheets

Science.gov (United States)

Kalantar-Zadeh, Kourosh; Tang, Jianshi; Wang, Minsheng; Wang, Kang L.; Shailos, Alexandros; Galatsis, Kosmas; Kojima, Robert; Strong, Veronica; Lech, Andrew; Wlodarski, Wojtek; Kaner, Richard B.

2010-03-01

The formation of MoO3 sheets of nanoscale thickness is described. They are made from several fundamental sheets of orthorhombic α-MoO3, which can be processed in large quantities via a low cost synthesis route that combines thermal evaporation and mechanical exfoliation. These fundamental sheets consist of double-layers of linked distorted MoO6 octahedra. Atomic force microscopy (AFM) measurements show that the minimum resolvable thickness of these sheets is 1.4 nm which is equivalent to the thickness of two double-layers within one unit cell of the α-MoO3 crystal.

2015 Resident Survey (City and County)

Data.gov (United States)

City and County of Durham, North Carolina — The purpose of the annual City/County survey: To objectively assess citizen satisfaction with the delivery of City/County servicesTo set a baseline for future...

2016 Resident Survey (City and County)

Data.gov (United States)

City and County of Durham, North Carolina — The purpose of the annual City/County survey: To objectively assess citizen satisfaction with the delivery of City/County servicesTo set a baseline for future...

Allegheny County Obesity Rates

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — Obesity rates for each Census Tract in Allegheny County were produced for the study “Developing small-area predictions for smoking and obesity prevalence in the...

Allegheny County Smoking Rates

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — Smoking rates for each Census Tract in Allegheny County were produced for the study “Developing small-area predictions for smoking and obesity prevalence in the...

Allegheny County Dam Locations

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — This dataset shows the point locations of dams in Allegheny County. If viewing this description on the Western Pennsylvania Regional Data Center’s open data portal...

Allegheny County Parks Outlines

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — Shows the size and shape of the nine Allegheny County parks. If viewing this description on the Western Pennsylvania Regional Data Center’s open data portal...

Allegheny County Property Viewer

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — Webmap of Allegheny municipalities and parcel data. Zoom for a clickable parcel map with owner name, property photograph, and link to the County Real Estate website...

Fact Sheets on Pesticides in Schools.

Science.gov (United States)

National Coalition against the Misuse of Pesticides, Washington, DC.

This document consists of a collection of fact sheets about the use of pesticides in schools and how to reduce it. The sheets are: (1) "Alternatives to Using Pesticides in Schools: What Is Integrated Pest Management?"; (2) "Health Effects of 48 Commonly Used Pesticides in Schools"; (3) "The Schooling of State Pesticide…

Single clay sheets inside electrospun polymer nanofibers

Science.gov (United States)

Sun, Zhaohui

2005-03-01

Nanofibers were prepared from polymer solution with clay sheets by electrospinning. Plasma etching, as a well controlled process, was used to supply electrically excited gas molecules from a glow discharge. To reveal the structure and arrangement of clay layers in the polymer matrix, plasma etching was used to remove the polymer by controlled gasification to expose the clay sheets due to the difference in reactivity. The shape, flexibility, and orientation of clay sheets were studied by transmission and scanning electron microscopy. Additional quantitative information on size distribution and degree of exfoliation of clay sheets were obtained by analyzing electron micrograph of sample after plasma etching. Samples in various forms including fiber, film and bulk, were thinned by plasma etching. Morphology and dispersion of inorganic fillers were studied by electron microscopy.

Complex world-sheets from N=2 strings

International Nuclear Information System (INIS)

Barbon, J.L.F.

1996-01-01

We study some properties of target space strings constructed from (2,1) heterotic strings. We argue that world-sheet complexification is a general property of the bosonic sector of such target world-sheets. We give a target space interpretation of this fact and relate it to the non-gaussian nature of free string field theory. We provide several one-loop calculations supporting the stringy construction of critical world-sheets in terms of (2,1) models. Using finite-temperature boundary conditions in the underlying (2,1) string we obtain non-chiral target space spin structures, and point out some of the problems arising for chiral spin structures, such as the heterotic world-sheet. To this end, we study the torus partition function of the corresponding asymmetric orbifold of the (2,1) string. (orig.)

Allegheny County Beltway System Street Centerlines

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — Authoritative dataset of the beltway system in Allegheny County. The system was developed to help motorists navigate through Allegheny County on low-traffic roads....

Motion and shape of snowplough sheets in coaxial accelerators

International Nuclear Information System (INIS)

Tsagas, N.F.; Mair, G.L.R.; Prinn, A.E.

1978-01-01

A long coaxial accelerator is filled with helium at initial gas pressure between 0.2 and 4 Torr. When connected to a large capacitor at < - 10 kV a discharge is started at one end; the central electrode has negative polarity. The velocity of the plasma sheet, the snowplough, and its shape have been derived from streak photographs for terminal currents between about 100 and 300 kA. The motion of the sheet has been analysed by balancing the electromagnetic driving force against the inertia of the mass of the gas swept up by a plane sheet taken to be impenetrable to gas atoms. The calculated positions and average sheet velocities, which involve simplifying assumptions, have been found to be in good agreement with observations at different positions and pressures. Also the shape of the sheet has been derived by allowing for the sheet's curvature in the linear momentum equation while net radial motions causing variations in profile have, at first, been excluded. The calculated shape of the sheet is very nearly that photographically observed. The axial velocity of a sheet element is evaluated under the assumption that the plasma is azimuthally uniform, free of spikes and that the vessel's wall does not affect the shape. (author)

Corrosion Behavior of Brazed Zinc-Coated Structured Sheet Metal

Directory of Open Access Journals (Sweden)

A. Nikitin

2017-01-01

Full Text Available Arc brazing has, in comparison to arc welding, the advantage of less heat input while joining galvanized sheet metals. The evaporation of zinc is reduced in the areas adjacent to the joint and improved corrosion protection is achieved. In the automotive industry, lightweight design is a key technology against the background of the weight and environment protection. Structured sheet metals have higher stiffness compared to typical automobile sheet metals and therefore they can play an important role in lightweight structures. In the present paper, three arc brazing variants of galvanized structured sheet metals were validated in terms of the corrosion behavior. The standard gas metal arc brazing, the pulsed arc brazing, and the cold metal transfer (CMT® in combination with a pulsed cycle were investigated. In experimental climate change tests, the influence of the brazing processes on the corrosion behavior of galvanized structured sheet metals was investigated. After that, the corrosion behavior of brazed structured and flat sheet metals was compared. Because of the selected lap joint, the valuation of damage between sheet metals was conducted. The pulsed CMT brazing has been derived from the results as the best brazing method for the joining process of galvanized structured sheet metals.

Allegheny County Employee Salaries

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — Employee salaries are a regular Right to Know request the County receives. Here is the disclaimer language that is included with the dataset from the Open Records...

Allegheny County Asbestos Permits

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — Current asbestos permit data issued by the County for commercial building demolitions and renovations as required by the EPA. This file is updated daily and can be...

Orientation and Morphology Effects in Rapid Silicon Sheet Solidification

Science.gov (United States)

Ciszek, T. F.

1984-01-01

Radial growth anisotropies and equilibrium forms of point nucleated, dislocation free silicon sheets spreading horizontally on the free surface of a silicon melt were measured for (100), (110), (111), and (112) sheet planes. The growth process was recorded. Qualitative Wulff surface free energy polar plots were deduced from the equilibrium shapes for each sheet plane. Predicted geometries for the tip shape of unidirectional, dislocation free, horizontally grown sheets growing in various directions within the planes were analyzed. Polycrystalline sheets and dendrite propagation were analyzed. For dendrites, growth rates on the order of 2.5 m/min and growth rate anisotropies of 25 are measured.

47 CFR 32.101 - Structure of the balance sheet accounts.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 2 2010-10-01 2010-10-01 false Structure of the balance sheet accounts. 32.101... UNIFORM SYSTEM OF ACCOUNTS FOR TELECOMMUNICATIONS COMPANIES Instructions for Balance Sheet Accounts § 32.101 Structure of the balance sheet accounts. The Balance Sheet accounts shall be maintained as follows...

Molding cork sheets to complex shapes

Science.gov (United States)

Sharpe, M. H.; Simpson, W. G.; Walker, H. M.

1977-01-01

Partially cured cork sheet is easily formed to complex shapes and then final-cured. Temperature and pressure levels required for process depend upon resin system used and final density and strength desired. Sheet can be bonded to surface during final cure, or can be first-formed in mold and bonded to surface in separate step.

Whooping Cough (Pertussis) - Fact Sheet for Parents

Science.gov (United States)

... months 4 through 6 years Fact Sheet for Parents Color [2 pages] Español: Tosferina (pertussis) The best ... according to the recommended schedule. Fact Sheets for Parents Diseases and the Vaccines that Prevent Them Chickenpox ...

Characterization of Tensile Mechanical Behavior of MSCs/PLCL Hybrid Layered Sheet

Directory of Open Access Journals (Sweden)

Azizah Intan Pangesty

2016-06-01

Full Text Available A layered construct was developed by combining a porous polymer sheet and a cell sheet as a tissue engineered vascular patch. The primary objective of this study is to investigate the influence of mesenchymal stem cells (MSCs sheet on the tensile mechanical properties of porous poly-(l-lactide-co-ε-caprolactone (PLCL sheet. The porous PLCL sheet was fabricated by the solid-liquid phase separation method and the following freeze-drying method. The MSCs sheet, prepared by the temperature-responsive dish, was then layered on the top of the PLCL sheet and cultured for 2 weeks. During the in vitro study, cellular properties such as cell infiltration, spreading and proliferation were evaluated. Tensile test of the layered construct was performed periodically to characterize the tensile mechanical behavior. The tensile properties were then correlated with the cellular properties to understand the effect of MSCs sheet on the variation of the mechanical behavior during the in vitro study. It was found that MSCs from the cell sheet were able to migrate into the PLCL sheet and actively proliferated into the porous structure then formed a new layer of MSCs on the opposite surface of the PLCL sheet. Mechanical evaluation revealed that the PLCL sheet with MSCs showed enhancement of tensile strength and strain energy density at the first week of culture which is characterized as the effect of MSCs proliferation and its infiltration into the porous structure of the PLCL sheet. New technique was presented to develop tissue engineered patch by combining MSCs sheet and porous PLCL sheet, and it is expected that the layered patch may prolong biomechanical stability when implanted in vivo.

The storm time central plasma sheet

Directory of Open Access Journals (Sweden)

R. Schödel

2002-11-01

Full Text Available The plasma sheet plays a key role during magnetic storms because it is the bottleneck through which large amounts of magnetic flux that have been eroded from the dayside magnetopause have to be returned to the dayside magnetosphere. Using about five years of Geotail data we studied the average properties of the near- and midtail central plasma sheet (CPS in the 10–30 RE range during magnetic storms. The earthward flux transport rate is greatly enhanced during the storm main phase, but shows a significant earthward decrease. Hence, since the magnetic flux cannot be circulated at a sufficient rate, this leads to an average dipolarization of the central plasma sheet. An increase of the specific entropy of the CPS ion population by a factor of about two during the storm main phase provides evidence for nonadiabatic heating processes. The direction of flux transport during the main phase is consistent with the possible formation of a near-Earth neutral line beyond ~20 RE.Key words. Magnetospheric physics (plasma convection; plasma sheet; storms and substorms

New directions in the science and technology of advanced sheet explosive formulations and the key energetic materials used in the processing of sheet explosives: Emerging trends.

Science.gov (United States)

Talawar, M B; Jangid, S K; Nath, T; Sinha, R K; Asthana, S N

2015-12-30

This review presents the work carried out by the international community in the area of sheet explosive formulations and its applications in various systems. The sheet explosive is also named as PBXs and is a composite material in which solid explosive particles like RDX, HMX or PETN are dispersed in a polymeric matrix, forms a flexible material that can be rolled/cut into sheet form which can be applied to any complex contour. The designed sheet explosive must possess characteristic properties such as flexible, cuttable, water proof, easily initiable, and safe handling. The sheet explosives are being used for protecting tanks (ERA), light combat vehicle and futuristic infantry carrier vehicle from different attacking war heads etc. Besides, sheet explosives find wide applications in demolition of bridges, ships, cutting and metal cladding. This review also covers the aspects such as risks and hazard analysis during the processing of sheet explosive formulations, effect of ageing on sheet explosives, detection and analysis of sheet explosive ingredients and the R&D efforts of Indian researchers in the development of sheet explosive formulations. To the best of our knowledge, there has been no review article published in the literature in the area of sheet explosives. Copyright © 2015 Elsevier B.V. All rights reserved.

STEVENSON-WYDLER (15 USC 3710) COOPERATIVE RESEARCH AND DEVELOPMENT AGREEMENT No. JSA 2009S007 BETWEEN Jefferson ScienceAssociates, LLC under its U.S.Department of Energy Contract No. DE-AC05-060R23 177 AND Black Laboratories, L.L.C.

Energy Technology Data Exchange (ETDEWEB)

Crooks, Roy [Black Lab., LLC, Newport News, VA (United States)

2018-02-08

The Cooperative Research and Development agreement, No. JSA 2009S00 resulted in collaborations and conference participations on research topics related to high purity (RRR) niobium applications for superconducting radio frequency cavities used by Jefferson Lab. Documented results were shown in Reports and Publications listed below. Reports were issued to The Commonwealth of Virginia, Center for Innovative Technology; to ATI Wah-Chang and several publications were produced with DESY in Hamburg, Germany, with Jefferson Lab and with Christopher Newport University.

Australian Government Balance Sheet Management

OpenAIRE

Wilson Au-Yeung; Jason McDonald; Amanda Sayegh

2006-01-01

Since almost eliminating net debt, the Australian Government%u2019s attention has turned to the financing of broader balance sheet liabilities, such as public sector superannuation. Australia will be developing a significant financial asset portfolio in the %u2018Future Fund%u2019 to smooth the financing of expenses through time. This raises the significant policy question of how best to manage the government balance sheet to reduce risk. This paper provides a framework for optimal balance sh...

Energy information sheets, July 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-07-01

The National Energy Information Center (NEIC), as part of its mission, provides energy information and referral assistance to Federal, State, and local governments, the academic community, business and industrial organizations, and the public. The Energy Information Sheets was developed to provide general information on various aspects of fuel production, prices, consumption, and capability. Additional information on related subject matter can be found in other Energy Information Administration (EIA) publications as referenced at the end of each sheet.

Energy information sheets, September 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-09-01

The National Energy Information Center (NEIC), as part of its mission, provides energy information and referral assistance to Federal, State, and local governments, the academic community, business and industrial organizations, and the public. The Energy Information Sheets was developed to provide general information on various aspects of fuel production, prices, consumption, and capability. Additional information on related subject matter can be found in other Energy Information Administration (EIA) publications as referenced at the end of each sheet.

Allegheny County Watershed Boundaries

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — This dataset demarcates the 52 isolated sub-Watersheds of Allegheny County that drain to single point on the main stem rivers. Created by 3 Rivers 2nd Nature based...

75 FR 13297 - Southeastern Lincoln County Habitat Conservation Plan, Lincoln County, NV

Science.gov (United States)

2010-03-19

... development), flood control activities (within the City of Caliente), maintenance of Lincoln County roads and... library locations: (1) Clark County Library, 1401 E. Flamingo Road, Las Vegas, NV 89119; (702) 507-3400.... 1538(a)(1)(B)). The term ``take'' means to harass, harm, pursue, hunt, shoot, wound, kill, trap...

Anesthesia Fact Sheet

Science.gov (United States)

... Education About NIGMS NIGMS Home > Science Education > Anesthesia Anesthesia Tagline (Optional) Middle/Main Content Area En español ... Version (464 KB) Other Fact Sheets What is anesthesia? Anesthesia is a medical treatment that prevents patients ...

Ice flow Modelling of the Greenland Ice Sheet

DEFF Research Database (Denmark)

Nielsen, Lisbeth Tangaa

Models of ice flow have a range of application in glaciology, including investigating the large-scale response of ice sheets to changes in climate, assimilating data to estimate unknown conditions beneath the ice sheet, and in interpreting proxy records obtained from ice cores, among others. In t...... a steady state with respect to the reference climate at the end of the simulation and that the mass balance of the ice sheet at this time was more sensitive to recent climate fluctuations than the temperature forcing in the early or mid-Holocene.......Models of ice flow have a range of application in glaciology, including investigating the large-scale response of ice sheets to changes in climate, assimilating data to estimate unknown conditions beneath the ice sheet, and in interpreting proxy records obtained from ice cores, among others....... In this PhD project, the use of ice flow models for the interpretation of the age-structure of the Greenland ice sheet, i.e. the depth within the ice, at which ice deposited at given times are found at present day. Two different observational data sets of this archive were investigated. Further, paleo...

Forced tearing of ductile and brittle thin sheets.

Science.gov (United States)

Tallinen, T; Mahadevan, L

2011-12-09

Tearing a thin sheet by forcing a rigid object through it leads to complex crack morphologies; a single oscillatory crack arises when a tool is driven laterally through a brittle sheet, while two diverging cracks and a series of concertinalike folds forms when a tool is forced laterally through a ductile sheet. On the other hand, forcing an object perpendicularly through the sheet leads to radial petallike tears in both ductile and brittle materials. To understand these different regimes we use a combination of experiments, simulations, and simple theories. In particular, we describe the transition from brittle oscillatory tearing via a single crack to ductile concertina tearing with two tears by deriving laws that describe the crack paths and wavelength of the concertina folds and provide a simple phase diagram for the morphologies in terms of the material properties of the sheet and the relative size of the tool.

Self-inhibiting growth of the Greenland Ice Sheet

DEFF Research Database (Denmark)

Langen, Peter Lang; Solgaard, Anne Munck; Hvidberg, Christine Schøtt

2012-01-01

The build-up of the Greenland Ice Sheet (GrIS) from ice-free conditions is studied in an ice sheet model (ISM) driven by fields from an atmospheric general circulation model (GCM) to demonstrate the importance of coupling between the two components. Experiments where the two are coupled off-line...... are augmented by one where an intermediate ice sheet configuration is coupled back to the GCM. Forcing the ISM with GCM fields corresponding to the ice-free state leads to extensive regrowth which, however, is halted when the intermediate recoupling step is included. This inhibition of further growth is due...... to a Föhn effect of moist air parcels being lifted over the intermediate ice sheet and arriving in the low-lying Greenland interior with high temperatures. This demonstrates that two-way coupling between the atmosphere and the ice sheet is essential for understanding the dynamics and that large scale...

Antibubbles and fine cylindrical sheets of air

KAUST Repository

Beilharz, D.

2015-08-14

Drops impacting at low velocities onto a pool surface can stretch out thin hemispherical sheets of air between the drop and the pool. These air sheets can remain intact until they reach submicron thicknesses, at which point they rupture to form a myriad of microbubbles. By impacting a higher-viscosity drop onto a lower-viscosity pool, we have explored new geometries of such air films. In this way we are able to maintain stable air layers which can wrap around the entire drop to form repeatable antibubbles, i.e. spherical air layers bounded by inner and outer liquid masses. Furthermore, for the most viscous drops they enter the pool trailing a viscous thread reaching all the way to the pinch-off nozzle. The air sheet can also wrap around this thread and remain stable over an extended period of time to form a cylindrical air sheet. We study the parameter regime where these structures appear and their subsequent breakup. The stability of these thin cylindrical air sheets is inconsistent with inviscid stability theory, suggesting stabilization by lubrication forces within the submicron air layer. We use interferometry to measure the air-layer thickness versus depth along the cylindrical air sheet and around the drop. The air film is thickest above the equator of the drop, but thinner below the drop and up along the air cylinder. Based on microbubble volumes, the thickness of the cylindrical air layer becomes less than 100 nm before it ruptures.

Antibubbles and fine cylindrical sheets of air

KAUST Repository

Beilharz, D.; Guyon, A.; Li, E.  Q.; Thoraval, M.-J.; Thoroddsen, Sigurdur T

2015-01-01

Drops impacting at low velocities onto a pool surface can stretch out thin hemispherical sheets of air between the drop and the pool. These air sheets can remain intact until they reach submicron thicknesses, at which point they rupture to form a myriad of microbubbles. By impacting a higher-viscosity drop onto a lower-viscosity pool, we have explored new geometries of such air films. In this way we are able to maintain stable air layers which can wrap around the entire drop to form repeatable antibubbles, i.e. spherical air layers bounded by inner and outer liquid masses. Furthermore, for the most viscous drops they enter the pool trailing a viscous thread reaching all the way to the pinch-off nozzle. The air sheet can also wrap around this thread and remain stable over an extended period of time to form a cylindrical air sheet. We study the parameter regime where these structures appear and their subsequent breakup. The stability of these thin cylindrical air sheets is inconsistent with inviscid stability theory, suggesting stabilization by lubrication forces within the submicron air layer. We use interferometry to measure the air-layer thickness versus depth along the cylindrical air sheet and around the drop. The air film is thickest above the equator of the drop, but thinner below the drop and up along the air cylinder. Based on microbubble volumes, the thickness of the cylindrical air layer becomes less than 100 nm before it ruptures.

Nonparaxial Bessel and Bessel-Gauss pincers light-sheets

Science.gov (United States)

Mitri, F. G.

2017-01-01

Nonparaxial optical Bessel and Bessel-Gauss pincers optical-sheets are introduced based upon the angular spectrum decomposition in plane waves. The angular spectrum function and the beam-shape coefficients are expressed by means of improper integrals computed numerically. The radiated component of the electric field is also evaluated, displaying unique features of the nonparaxial Bessel pincers light-sheets. This new type of auto-focusing light-sheets finds potential applications in the development of novel methods in optical light-sheet tweezers for particle manipulation in opto-fluidics, particle sizing and imaging. Numerical predictions for the scattering, radiation force and torque, and particle dynamics also benefit from the developed beam solution.

Ice Sheet Roughness Estimation Based on Impulse Responses Acquired in the Global Ice Sheet Mapping Orbiter Mission

Science.gov (United States)

Niamsuwan, N.; Johnson, J. T.; Jezek, K. C.; Gogineni, P.

2008-12-01

The Global Ice Sheet Mapping Orbiter (GISMO) mission was developed to address scientific needs to understand the polar ice subsurface structure. This NASA Instrument Incubator Program project is a collaboration between Ohio State University, the University of Kansas, Vexcel Corporation and NASA. The GISMO design utilizes an interferometric SAR (InSAR) strategy in which ice sheet reflected signals received by a dual-antenna system are used to produce an interference pattern. The resulting interferogram can be used to filter out surface clutter so as to reveal the signals scattered from the base of the ice sheet. These signals are further processed to produce 3D-images representing basal topography of the ice sheet. In the past three years, the GISMO airborne field campaigns that have been conducted provide a set of useful data for studying geophysical properties of the Greenland ice sheet. While topography information can be obtained using interferometric SAR processing techniques, ice sheet roughness statistics can also be derived by a relatively simple procedure that involves analyzing power levels and the shape of the radar impulse response waveforms. An electromagnetic scattering model describing GISMO impulse responses has previously been proposed and validated. This model suggested that rms-heights and correlation lengths of the upper surface profile can be determined from the peak power and the decay rate of the pulse return waveform, respectively. This presentation will demonstrate a procedure for estimating the roughness of ice surfaces by fitting the GISMO impulse response model to retrieved waveforms from selected GISMO flights. Furthermore, an extension of this procedure to estimate the scattering coefficient of the glacier bed will be addressed as well. Planned future applications involving the classification of glacier bed conditions based on the derived scattering coefficients will also be described.

Development Track of Different County-Level Towns

OpenAIRE

ZHANG, Haijiao; ZHANG, Zhenghe

2015-01-01

County-level town is important space carrier of China’s urbanization and the emphasis and key of strategic distribution for urbanization. Backwardness of county-level towns limits nearby transfer of surplus labor. To promote development of county-level towns, on the basis of classifying county-level towns, this paper analyzed motive and resistance factors of evolution of different county-level towns using historical data collection and statistical method, comparative approach, typical case ...

Allegheny County Block Areas

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — This dataset overlays a grid on the County to assist in locating a parcel. The grid squares are 3,500 by 4,500 square feet. The data was derived from original...

Protein unfolding versus β-sheet separation in spider silk nanocrystals

International Nuclear Information System (INIS)

Alam, Parvez

2014-01-01

In this communication a mechanism for spider silk strain hardening is proposed. Shear failure of β-sheet nanocrystals is the first failure mode that gives rise to the creation of smaller nanocrystals, which are of higher strength and stiffness. β-sheet unfolding requires more energy than nanocrystal separation in a shear mode of failure. As a result, unfolding occurs after the nanocrystals separate in shear. β-sheet unfolding yields a secondary strain hardening effect once the β-sheet conformation is geometrically stable and acts like a unidirectional fibre in a fibre reinforced composite. The mechanism suggested herein is based on molecular dynamics calculations of residual inter-β-sheet separation strengths against residual intra-β-sheet unfolding strengths. (paper)

Cerebral Palsy: General Information. Fact Sheet Number 2 = La Paralisis Cerebral: Informacion General. Fact Sheet Number 18.

Science.gov (United States)

Interstate Research Associates, McLean, VA.

This fact sheet on cerebral palsy is offered in both English and Spanish. First, it provides a definition and considers various causes (e.g., an insufficient amount of oxygen reaching the fetal or newborn brain). The fact sheet then offers incidence figures and explains characteristics of the three main types of cerebral palsy: spastic, athetoid,…

Film sheet cassette

International Nuclear Information System (INIS)

1981-01-01

A novel film sheet cassette is described for handling CAT photographic films under daylight conditions and facilitating their imaging. A detailed description of the design and operation of the cassette is given together with appropriate illustrations. The resulting cassette is a low-cost unit which is easily constructed and yet provides a sure light-tight seal for the interior contents of the cassette. The individual resilient fingers on the light-trap permit the ready removal of the slide plate for taking pictures. The stippled, non-electrostatic surface of the pressure plate ensures an air layer and free slidability of the film for removal and withdrawal of the film sheet. The advantage of the daylight system is that a darkroom need not be used for inserting and removing the film in and out of the cassette resulting in a considerable time saving. (U.K.)

An Adaptive Test Sheet Generation Mechanism Using Genetic Algorithm

Directory of Open Access Journals (Sweden)

Huan-Yu Lin

2012-01-01

Full Text Available For test-sheet composition systems, it is important to adaptively compose test sheets with diverse conceptual scopes, discrimination and difficulty degrees to meet various assessment requirements during real learning situations. Computation time and item exposure rate also influence performance and item bank security. Therefore, this study proposes an Adaptive Test Sheet Generation (ATSG mechanism, where a Candidate Item Selection Strategy adaptively determines candidate test items and conceptual granularities according to desired conceptual scopes, and an Aggregate Objective Function applies Genetic Algorithm (GA to figure out the approximate solution of mixed integer programming problem for the test-sheet composition. Experimental results show that the ATSG mechanism can efficiently, precisely generate test sheets to meet the various assessment requirements than existing ones. Furthermore, according to experimental finding, Fractal Time Series approach can be applied to analyze the self-similarity characteristics of GA’s fitness scores for improving the quality of the test-sheet composition in the near future.

Simulations of the Scandinavian ice sheet and its subsurface conditions

International Nuclear Information System (INIS)

Boulton, G.S.; Caban, P.; Hulton, N.

1999-12-01

An ice sheet model has been applied to an approximate flow line through the area of the Fennoscandian ice sheet. The modelled ice sheet fluctuations have been matched with stratigraphic evidence of Weichselian ice sheet fluctuation in order to simulate ice sheet attributes through time along the flowline. The model predicts extensive melting at the base of the ice sheet. This output has been used as an input to a simplified model of hydrogeology along the southern flank of the ice sheet so as to reconstruct patterns of subglacial groundwater flow. The output from the model is also used to estimate patterns of subglacial stress and strain. Results suggest that large scale subglacial groundwater catchment are formed which were quite different in extent from modern catchment; that fossil subglacial groundwaters should be found at sampling depths; and much fracturing in shallow bedrock in Sweden could be glacially generated

Simulations of the Scandinavian ice sheet and its subsurface conditions

Energy Technology Data Exchange (ETDEWEB)

Boulton, G.S.; Caban, P.; Hulton, N. [Edinburgh Univ. (United Kingdom). Dept of Geology and Geophysics

1999-12-01

An ice sheet model has been applied to an approximate flow line through the area of the Fennoscandian ice sheet. The modelled ice sheet fluctuations have been matched with stratigraphic evidence of Weichselian ice sheet fluctuation in order to simulate ice sheet attributes through time along the flowline. The model predicts extensive melting at the base of the ice sheet. This output has been used as an input to a simplified model of hydrogeology along the southern flank of the ice sheet so as to reconstruct patterns of subglacial groundwater flow. The output from the model is also used to estimate patterns of subglacial stress and strain. Results suggest that large scale subglacial groundwater catchment are formed which were quite differentin extent from modern catchment; that fossil subglacial groundwaters should be found at sampling depths; and much fracturing in shallow bedrock in Sweden could be glacially generated.

Synthesis, characterization and optical properties of sheet-like ZnO

International Nuclear Information System (INIS)

Liu, Changzhen; Meng, Dawei; Wu, Xiuling; Wang, Yongqian; Yu, Xiaohong; Zhang, Zhengjie; Liu, Xiaoyang

2011-01-01

Highlights: → Sheet-like ZnO with regular hexagon shape was synthesized with a two-step method. → Sheet-like ZnO predecessor was synthesized at low temperature in open system. → The diameter and thickness of ZnO sheet can be controlled conveniently. → This low-cost and environmentally benign approach is controllable and reproducible. → Sheet-like ZnO may have potential application in optical and electrical devices. -- Abstract: Sheet-like ZnO with regular hexagon shape and uniform diameter has been successfully synthesized through a two-step method without any metal catalyst. First, the sheet-like ZnO precursor was synthesized in a weak alkaline carbamide environment with stirring in a constant temperature water-bath by the homogeneous precipitation method, then sheet-like ZnO was obtained by calcining at 600 o C for 2 h. The structures and optical properties of sheet-like ZnO have been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), photoluminescence (PL) and UV-vis-NIR spectrophotometer. The results reveal that the product is highly crystalline with hexagonal wurtzite phase and has appearance of hexagon at (0 0 0 1) plane. The HRTEM images confirm that the individual sheet-like ZnO is single crystal. The PL spectrum exhibits a narrow ultraviolet emission at 397 nm and a broad visible emission centering at 502 nm. The band gap of sheet-like ZnO is about 3.15 eV.

Comparison of Corrosion Behavior of Electrochemically Deposited Nano-Cobalt-Coated Ni Sheet

Directory of Open Access Journals (Sweden)

Nasser Al-Aqeeli

2013-01-01

Full Text Available Corrosion behavior of nano-coblat-coated Ni sheet was compared with pure Ni and 20% Fe-Ni alloy sheet using potentiodynamic polarization and linear polarization technique in 0.1 M NaCl solution at room temperature. Results showed that corrosion resistance properties of nano-Co-coated Ni sheet were almost same as that of pure Ni sheet, however corrosion resistance of 20% Fe-Ni sheet was decreased significantly. Pitting potential of 20% Fe-Ni sheet was subsequently decreased as compared to pure Ni sheet as well as nano-cobalt-coated Ni sheet. SEM/EDS analysis of the corroded surfaces showed that both pure Ni and nano-coblat-coated Ni sheet did not show any appreciable corrosion however significant corrosion was observed in the case of 20% Fe-Ni sheet.

Implementation of the Polarized HD target at the Thomas Jefferson National Accelerator Facility

International Nuclear Information System (INIS)

Chaden Djalali; David Tedeschi

2007-01-01

The original goal of this proposal was to study frozen spin polarized targets (HD target and other technologies) and produce a conceptual design report for the implementation of such a target in the HALL B detector of the Thomas Jefferson National Accelerator Facility (JLab). During the first two years of the proposal, we came to the conclusion that the best suited target for JLab was a frozen spin target and helped with the design of such a target. We have not only achieved our original goal but have exceeded it by being involved in the actual building and testing of parts the target. The main reason for this success has been the hiring of a senior research associate, Dr. Oleksandr Dzyubak, who had more than 10 years of experience in the field of frozen spin polarized targets. The current grant has allowed the USC nuclear physics group to strengthen its role in the JLab collaboration and make important contribution to both the detector development and the scientific program

14 CFR Section 3 - Chart of Balance Sheet Accounts

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Chart of Balance Sheet Accounts Section 3 Section 3 Aeronautics and Space OFFICE OF THE SECRETARY, DEPARTMENT OF TRANSPORTATION (AVIATION... Balance Sheet Classifications Section 3 Chart of Balance Sheet Accounts [See footnotes at end of table...

17 CFR 229.1001 - (Item 1001) Summary term sheet.

Science.gov (United States)

2010-04-01

... sheet that is written in plain English. The summary term sheet must briefly describe in bullet point format the most material terms of the proposed transaction. The summary term sheet must provide security... transaction. The bullet points must cross-reference a more detailed discussion contained in the disclosure...

Theoretical Predictions of Freestanding Honeycomb Sheets of Cadmium Chalcogenides

Energy Technology Data Exchange (ETDEWEB)

Zhou, Jia [ORNL; Huang, Jingsong [ORNL; Sumpter, Bobby G [ORNL; Kent, Paul R [ORNL; Xie, Yu [ORNL; Terrones Maldonado, Humberto [ORNL; Smith, Sean C [ORNL

2014-01-01

Two-dimensional (2D) nanocrystals of CdX (X = S, Se, Te) typically grown by colloidal synthesis are coated with organic ligands. Recent experimental work on ZnSe showed that the organic ligands can be removed at elevated temperature, giving a freestanding 2D sheet of ZnSe. In this theoretical work, freestanding single- to few-layer sheets of CdX, each possessing a pseudo honeycomb lattice, are considered by cutting along all possible lattice planes of the bulk zinc blende (ZB) and wurtzite (WZ) phases. Using density functional theory, we have systematically studied their geometric structures, energetics, and electronic properties. A strong surface distortion is found to occur for all of the layered sheets, and yet all of the pseudo honeycomb lattices are preserved, giving unique types of surface corrugations and different electronic properties. The energetics, in combination with phonon mode calculations and molecular dynamics simulations, indicate that the syntheses of these freestanding 2D sheets could be selective, with the single- to few-layer WZ110, WZ100, and ZB110 sheets being favored. Through the GW approximation, it is found that all single-layer sheets have large band gaps falling into the ultraviolet range, while thicker sheets in general have reduced band gaps in the visible and ultraviolet range. On the basis of the present work and the experimental studies on freestanding double-layer sheets of ZnSe, we envision that the freestanding 2D layered sheets of CdX predicted herein are potential synthesis targets, which may offer tunable band gaps depending on their structural features including surface corrugations, stacking motifs, and number of layers.

NTPR Fact Sheets

Science.gov (United States)

History Documents US Underground Nuclear Test History Reports NTPR Radiation Exposure Reports Enewetak Atoll Cleanup Documents TRAC About Who We Are Our Values History Locations Our Leadership Director Support Center Contact Us FAQ Sheet Links Success Stories Contracts Business Opportunities Current

The social balance sheet 2004

OpenAIRE

Ph. Delhez; P. Heuse

2005-01-01

Each year, in the 4th quarter’s Economic Review, the National Bank examines the provisional results of the social balance sheets. As all the social balance sheets are not yet available for 2004, the study is based on a limited population of enterprises, compiled according to the principle of a constant sample. This population is made up of 38,530 enterprises employing around 1,331,000 workers in 2004. The main results of the analysis, in terms of employment, working hours, labour cost and tra...

Analysis of Financial Position Based on the Balance Sheet

OpenAIRE

Spineanu-Georgescu Luciana

2011-01-01

Analysis of financial position based on the balance sheet is mainly aimed at assessing the extent to which financial structure chosen by the firm, namely, financial resources, covering the needs reflected in the balance sheet financed. This is done through an analysis known as horizontal analysis balance sheet financial imbalances.

Sense and readability: participant information sheets for research studies.

Science.gov (United States)

Ennis, Liam; Wykes, Til

2016-02-01

Informed consent in research is partly achieved through the use of information sheets. There is a perception however that these information sheets are long and complex. The recommended reading level for patient information is grade 6, or 11-12 years old. To investigate whether the readability of participant information sheets has changed over time, whether particular study characteristics are related to poorer readability and whether readability and other study characteristics are related to successful study recruitment. Method: We obtained 522 information sheets from the UK National Institute for Health Research Clinical Research Network: Mental Health portfolio database and study principal investigators. Readability was assessed with the Flesch reading index and the Grade level test. Information sheets increased in length over the study period. The mean grade level across all information sheets was 9.8, or 15-16 years old. A high level of patient involvement was associated with more recruitment success and studies involving pharmaceutical or device interventions were the least successful. The complexity of information sheets had little bearing on successful recruitment. Information sheets are far more complex than the recommended reading level of grade 6 for patient information. The disparity may be exacerbated by an increasing focus on legal content. Researchers would benefit from clear guidance from ethics committees on writing succinctly and accessibly and how to balance the competing legal issues with the ability of participants to understand what a study entails. © The Royal College of Psychiatrists 2016.

Advanced friction modeling for sheet metal forming

NARCIS (Netherlands)

Hol, J.; Cid Alfaro, M.V.; de Rooij, Matthias B.; Meinders, Vincent T.

2012-01-01

The Coulomb friction model is frequently used for sheet metal forming simulations. This model incorporates a constant coefficient of friction and does not take the influence of important parameters such as contact pressure or deformation of the sheet material into account. This article presents a

Advanced friction modeling in sheet metal forming

NARCIS (Netherlands)

Hol, J.; Cid Alfaro, M.V.; Meinders, Vincent T.; Huetink, Han

2011-01-01

The Coulomb friction model is frequently used for sheet metal forming simulations. This model incorporates a constant coefficient of friction and does not take the influence of important parameters such as contact pressure or deformation of the sheet material into account. This article presents a

Application of decision support systems in county urban planning: a proposal for Macaé county

Directory of Open Access Journals (Sweden)

GALANTE, A. C.

2008-06-01

Full Text Available The Macaé County is one of the greatest economy of the state of Rio de Janeiro. With the use of the information technology is possible to create a powerful tool for supporting the decision making processing for this County, aiding the process of improvement of life quality. For that one, intends to use a Decision Support System able to give different kind of information of County areas, like health and education. For the union of all information the datawarehouse technology will be used. For query implementation the technologies of OLAP and GIS are used together. Therefore, those technologies together make a powerful tool for aiding the decision making process of the Macaé County.

Nonlinear dynamics of thin current sheets

International Nuclear Information System (INIS)

Daughton, William

2002-01-01

Observations indicate that the current sheet in the Earth's geomagnetic tail may compress to a thickness comparable to an ion gyro-radius prior to substorm onset. In recent years, there has been considerable controversy regarding the kinetic stability of these thin structures. In particular, the growth rate of the kink instability and its relevance to magnetotail dynamics is still being debated. In this work, a series of fully kinetic particle-in-cell simulations are performed for a thin Harris sheet. The ion to electron mass ratio is varied between m i /m e =4→400 and careful comparisons are made with a formally exact approach to the linear Vlasov theory. At low mass ratio m i /m e <64, the simulations are in excellent agreement with the linear theory, but at high mass ratio the kink instability is observed to grow more rapidly in the kinetic simulations than predicted by theory. The resolution to this apparent discrepancy involves the lower hybrid instability which is active on the edge of the sheet and rapidly produces nonlinear modifications to the initial equilibrium. The nature of this nonlinear deformation is characterized and a simple model is proposed to explain the physics. After the growth and saturation of the lower hybrid fluctuations, the deformed current sheet is similar in structure to a Harris equilibrium with an additional background population. This may explain the large growth rate of the kink instability at later times, since this type of modification to the Harris sheet has been shown to greatly enhance the growth rate of the kink mode

Photon and π"0 electroproduction at Jefferson Laboratory-Hall A

International Nuclear Information System (INIS)

Defurne, Maxime

2015-01-01

Defined in the mid 90's, the generalized parton distributions (GPDs) represent a higher level of information than the form factors and parton distribution functions: indeed they encapsulate the correlation between the fraction of longitudinal momentum and the transverse position of the partons inside the nucleon. Consequently we can access the distribution of the partons in the transverse plane according to their longitudinal momentum. Moreover we can derive the total angular orbital momentum of quarks thanks to Ji's sum rule. Experimentally, we access the GPDs through the study of deep exclusive processes (asymmetries, cross sections,...). A worldwide experimental program started in the early 2000's. This thesis presents two data analyses carried on two data sets from experiments running at Jefferson laboratory - Hall A in 2004 and 2010. From the 2004 data set, we have extracted unpolarized and polarized photon electroproduction cross sections. A careful study of the systematic errors has greatly improved the quality of the results. They seem to indicate the necessity to take into account target-mass and finite-t corrections up to twist-4. From the 2010 data set, we have performed the first separation of the longitudinal and transverse responses of neutral pion electroproduction. The results confirm the assumption of a significant contribution of the transverse response although kinematically suppressed with respect to the longitudinal response. These results of high precision validate the GPD approach and will allow to improve the existing models. (author) [fr

Ice Sheet Model Intercomparison Project (ISMIP6) contribution to CMIP6

Science.gov (United States)

Nowicki, Sophie M.J.; Payne, Tony; Larour, Eric; Seroussi, Helene; Goelzer, Heiko; Lipscomb, William; Gregory, Jonathan; Abe-Ouchi, Ayako; Shepherd, Andrew

2018-01-01

Reducing the uncertainty in the past, present and future contribution of ice sheets to sea-level change requires a coordinated effort between the climate and glaciology communities. The Ice Sheet Model Intercomparison Project for CMIP6 (ISMIP6) is the primary activity within the Coupled Model Intercomparison Project – phase 6 (CMIP6) focusing on the Greenland and Antarctic Ice Sheets. In this paper, we describe the framework for ISMIP6 and its relationship to other activities within CMIP6. The ISMIP6 experimental design relies on CMIP6 climate models and includes, for the first time within CMIP, coupled ice sheet – climate models as well as standalone ice sheet models. To facilitate analysis of the multi-model ensemble and to generate a set of standard climate inputs for standalone ice sheet models, ISMIP6 defines a protocol for all variables related to ice sheets. ISMIP6 will provide a basis for investigating the feedbacks, impacts, and sea-level changes associated with dynamic ice sheets and for quantifying the uncertainty in ice-sheet-sourced global sea-level change. PMID:29697697

Production (information sheets)

NARCIS (Netherlands)

2007-01-01

Documentation sheets: Geo energy 2 Integrated System Approach Petroleum Production (ISAPP) The value of smartness 4 Reservoir permeability estimation from production data 6 Coupled modeling for reservoir application 8 Toward an integrated near-wellbore model 10 TNO conceptual framework for "E&P

Allegheny County Snow Route Centerlines (2017-2018)

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — This dataset shows snow route responsibilities of Allegheny County-owned roads.Category: TransportationOrganization: Allegheny CountyDepartment: Geographic...

Evolution of the MHD sheet pinch

International Nuclear Information System (INIS)

Matthaeus, W.H.; Montgomery, D.

1979-01-01

A magnetohydrodynamic (MHD) problem of recurrent interest for both astrophysical and laboratory plasmas is the evolution of the unstable sheet pinch, a current sheet across which a dc magnetic field reverses sign. The evolution of such a sheet pinch is followed with a spectral-method, incompressible, two-dimensional, MHD turbulence code. Spectral diagnostics are employed, as are contour plots of vector potential (magnetic field lines), electric current density, and velocity stream function (velocity streamlines). The nonlinear effect which seems most important is seen to be current filamentation: the concentration of the current density onto sets of small measure near a mgnetic X point. A great deal of turbulence is apparent in the current distribution, which, for high Reynolds numbers, requires large spatial grids (greater than or equal to (64) 2 ). 11 figures, 1 table

Dipole-sheet multipole magnets for accelerators

International Nuclear Information System (INIS)

Walstrom, P.L.

1993-01-01

The dipole-sheet formalism can be used to describe both cylindrical current-sheet multipole magnets and cylindrical-bore magnets made up of permanent magnet blocks. For current sheets, the formalism provides a natural way of finding a finite set of turns that approximate a continuous distribution. The formalism is especially useful In accelerator applications where large-bore, short, high-field-quality magnets that are dominated by fringe fields are needed. A further advantage of the approach is that in systems with either open or cylindrically symmetric magnetic boundaries, analytical expressions for the three-dimensional fields that are suitable for rapid numerical evaluation can be derived. This development is described in some detail. Also, recent developments in higher-order particle-beam optics codes based on the formalism are described briefly

Influence of temperature fluctuations on equilibrium ice sheet volume

Science.gov (United States)

Bøgeholm Mikkelsen, Troels; Grinsted, Aslak; Ditlevsen, Peter

2018-01-01

Forecasting the future sea level relies on accurate modeling of the response of the Greenland and Antarctic ice sheets to changing temperatures. The surface mass balance (SMB) of the Greenland Ice Sheet (GrIS) has a nonlinear response to warming. Cold and warm anomalies of equal size do not cancel out and it is therefore important to consider the effect of interannual fluctuations in temperature. We find that the steady-state volume of an ice sheet is biased toward larger size if interannual temperature fluctuations are not taken into account in numerical modeling of the ice sheet. We illustrate this in a simple ice sheet model and find that the equilibrium ice volume is approximately 1 m SLE (meters sea level equivalent) smaller when the simple model is forced with fluctuating temperatures as opposed to a stable climate. It is therefore important to consider the effect of interannual temperature fluctuations when designing long experiments such as paleo-spin-ups. We show how the magnitude of the potential bias can be quantified statistically. For recent simulations of the Greenland Ice Sheet, we estimate the bias to be 30 Gt yr-1 (24-59 Gt yr-1, 95 % credibility) for a warming of 3 °C above preindustrial values, or 13 % (10-25, 95 % credibility) of the present-day rate of ice loss. Models of the Greenland Ice Sheet show a collapse threshold beyond which the ice sheet becomes unsustainable. The proximity of the threshold will be underestimated if temperature fluctuations are not taken into account. We estimate the bias to be 0.12 °C (0.10-0.18 °C, 95 % credibility) for a recent estimate of the threshold. In light of our findings it is important to gauge the extent to which this increased variability will influence the mass balance of the ice sheets.

County and Parish Boundaries - COUNTY_GOVERNMENT_BOUNDARIES_IDHS_IN: Governmental Boundaries Maintained by County Agencies in Indiana (Indiana Department of Homeland Security, Polygon feature class)

Data.gov (United States)

NSGIC State | GIS Inventory — COUNTY_GOVERNMENT_BOUNDARIES_IDHS_IN is a polygon feature class that contains governmental boundaries maintained by county agencies in Indiana, provided by personnel...

Search for baryon-number and lepton-number violating decays of Λ hyperons using the CLAS detector at Jefferson Laboratory

Science.gov (United States)

McCracken, M. E.; Bellis, M.; Adhikari, K. P.; Adikaram, D.; Akbar, Z.; Pereira, S. Anefalos; Badui, R. A.; Ball, J.; Baltzell, N. A.; Battaglieri, M.; Batourine, V.; Bedlinskiy, I.; Biselli, A. S.; Boiarinov, S.; Briscoe, W. J.; Brooks, W. K.; Burkert, V. D.; Cao, T.; Carman, D. S.; Celentano, A.; Chandavar, S.; Charles, G.; Colaneri, L.; Cole, P. L.; Contalbrigo, M.; Cortes, O.; Crede, V.; D'Angelo, A.; Dashyan, N.; De Vita, R.; De Sanctis, E.; Deur, A.; Djalali, C.; Dodge, G. E.; Dupre, R.; Alaoui, A. El; Fassi, L. El; Elouadrhiri, E.; Eugenio, P.; Fedotov, G.; Fegan, S.; Fersch, R.; Filippi, A.; Fleming, J. A.; Garillon, B.; Gevorgyan, N.; Gilfoyle, G. P.; Giovanetti, K. L.; Girod, F. X.; Golovatch, E.; Gothe, R. W.; Griffioen, K. A.; Guidal, M.; Guo, L.; Hafidi, K.; Hakobyan, H.; Hanretty, C.; Hattawy, M.; Hicks, K.; Holtrop, M.; Hughes, S. M.; Ilieva, Y.; Ireland, D. G.; Ishkhanov, B. S.; Isupov, E. L.; Jenkins, D.; Jiang, H.; Jo, H. S.; Keller, D.; Khachatryan, G.; Khandaker, M.; Kim, A.; Kim, W.; Klein, A.; Klein, F. J.; Kubarovsky, V.; Lenisa, P.; Livingston, K.; Lu, H. Y.; MacGregor, I. J. D.; Mayer, M.; McKinnon, B.; Mestayer, M. D.; Meyer, C. A.; Mirazita, M.; Mokeev, V.; Moody, C. I.; Moriya, K.; Camacho, C. Munoz; Nadel-Turonski, P.; Net, L. A.; Niccolai, S.; Osipenko, M.; Ostrovidov, A. I.; Park, K.; Pasyuk, E.; Pisano, S.; Pogorelko, O.; Price, J. W.; Procureur, S.; Prok, Y.; Raue, B. A.; Ripani, M.; Rizzo, A.; Rosner, G.; Roy, P.; Sabatié, F.; Salgado, C.; Schumacher, R. A.; Seder, E.; Sharabian, Y. G.; Skorodumina, Iu.; Sokhan, D.; Sparveris, N.; Stoler, P.; Strakovsky, I. I.; Strauch, S.; Sytnik, V.; Tian, Ye; Ungaro, M.; Voskanyan, H.; Voutier, E.; Walford, N. K.; Watts, D. P.; Wei, X.; Wood, M. H.; Zachariou, N.; Zana, L.; Zhang, J.; Zhao, Z. W.; Zonta, I.; CLAS Collaboration

2015-10-01

We present a search for ten baryon number violating decay modes of Λ hyperons using the CLAS detector at Jefferson Laboratory. Nine of these decay modes result in a single meson and single lepton in the final state (Λ →m ℓ) and conserve either the sum or the difference of baryon and lepton number (B ±L ). The tenth decay mode (Λ →p ¯ π+ ) represents a difference in baryon number of two units and no difference in lepton number. We observe no significant signal and set upper limits on the branching fractions of these reactions in the range (4 - 200 )×10-7 at the 90% confidence level.

Sheet Beam Klystron Instability Analysis

International Nuclear Information System (INIS)

Bane, K.

2009-01-01

Using the principle of energy balance we develop a 2D theory for calculating growth rates of instability in a two-cavity model of a sheet beam klystron. An important ingredient is a TE-like mode in the gap that also gives a longitudinal kick to the beam. When compared with a self-consistent particle-in-cell calculation, with sheet beam klystron-type parameters, agreement is quite good up to half the design current, 65 A; at full current, however, other, current-dependent effects come in and the results deviate significantly

COMPARATIVE ANALYSIS OF THE GORJ COUNTY OF SOCIO-ECONOMIC WITH NEIGHBORING COUNTIES IN CRISIS

Directory of Open Access Journals (Sweden)

CONSTANTA ENEA

2012-05-01

Full Text Available Purpose of the paper is to highlight how the economy evolved in the Florida county comparison with neighboring counties in economic crisis that society through the difficult years. also study and make acomparison in terms of demographic characteristics, respectively, compared between young and old, labor migration, etc. form., indices that are decisive for evaluating the economic situation of the county above mentioned. Economically, the county is in the connection between the economy and sub-mountainous and mountainous plains. The specificity of its resources, Gorj is a leading energy suppliers of the country, both as primary energy (coal, oil and processed (heat and electricity1. Results and statistical sources that Gorj currently produces more than 20% of the thermoelectric power of2. In terms of population below national averages Gorj is the fourth in the region after Olt and Valcea. Is medium in size, being the third after Dolj and Valcea. In terms of urbanization, Gorj is below the national average and third in the region after Dolj and Mehedinti. After the general level of development, the county is in a less favorable position, because the permanent part is characterized by a lower level of development.

Bi-directional electrons in the near-Earth plasma sheet

Directory of Open Access Journals (Sweden)

K. Shiokawa

2003-07-01

Full Text Available We have studied the occurrence characteristics of bi-directional electron pitch angle anisotropy (enhanced flux in field-aligned directions, F^ /F|| > 1.5 at energies of 0.1–30 keV using plasma and magnetic field data from the AMPTE/IRM satellite in the near-Earth plasma sheet. The occurrence rate increases in the tailward direction from XGSM = - 9 RE to - 19 RE . The occurrence rate is also enhanced in the midnight sector, and furthermore, whenever the elevation angle of the magnetic field is large while the magnetic field intensity is small, B ~ 15 nT. From these facts, we conclude that the bi-directional electrons in the central plasma sheet are produced mainly in the vicinity of the neutral sheet and that the contribution from ionospheric electrons is minor. A high occurrence is also found after earthward high-speed ion flows, suggesting Fermi-type field-aligned electron acceleration in the neutral sheet. Occurrence characteristics of bi-directional electrons in the plasma sheet boundary layer are also discussed.Key words. Magnetospheric physics (magnetospheric configuration and dynamics; magnetotail; plasma sheet

Firm Investment and Balance-Sheet Problems in Japan

OpenAIRE

Toshitaka Sekine

1999-01-01

This paper investigates whether balance-sheet conditions of firms and their main banks matter for firm investment behavior using dynamic corporate panel data in Japan for the period 1985-95. It finds that smaller non-bond issuing firms were facing liquidity constraints; these firms’ balance-sheet conditions (the debt asset ratios) affected their investment from the midst of the bubble era by influencing main banks’ lending to them; and the deterioration of their main banks’ balance-sheet cond...

Low-Wage Counties Face Locational Disadvantages.

Science.gov (United States)

Gibbs, Robert; Cromartie, John B.

2000-01-01

Small populations and remoteness are the most salient features of low-wage counties. These locational attributes coincide with fewer high-wage jobs, yet low wages within industries define low-wage counties more than industry composition. Although adults in low-wage counties have less education and labor force participation overall, the role played…

The quantitative inspection of iron aluminide green sheet using transient thermography

International Nuclear Information System (INIS)

Watkins, Michael L.; Hinders, Mark K.; Scorey, Clive; Winfree, William

1999-01-01

The recent development of manufacturing techniques for the fabrication of thin iron aluminide, FeAl, sheet requires advanced quantitative methods for on-line inspection. An understanding of the mechanisms responsible for flaws and the development of appropriate flaw detection methods are key elements in an effective quality management system. The first step in the fabrication of thin FeAl alloy sheet is the formation of a green sheet, either by cold rolling or tape casting FeAl powder mixed with organic binding agents. The finished sheet is obtained using a series of process steps involving binder elimination, densification, sintering, and annealing. Non-uniformities within the green sheet are the major contributor to material failure in subsequent sheet processing and the production of non-conforming finished sheet. Previous work has demonstrated the advantages of using active thermography to detect the flaws and heterogeneity within green powder composites (1)(2)(3). The production environment and physical characteristics of these composites provide for unique challenges in developing a rapid nondestructive inspection capability. Thermography is non-contact and minimizes the potential damage to the fragile green sheet. Limited access to the material also demands a one-sided inspection technique. In this paper, we will describe the application of thermography for 100% on-line inspection within an industrial process. This approach is cost competitive with alternative technologies, such as x-ray imaging systems, and provides the required sensitivity to the variations in material composition. The formation of green sheet flaws and their transformation into defects within intermediate and finished sheet products will be described. A green sheet conformance criterion will be presented which would significantly reduce the probability of processing poor quality green sheet which contributes to higher waste and inferior bulk alloy sheet

Antibubbles and fine cylindrical sheets of air

NARCIS (Netherlands)

Beilharz, D.; Guyon, A.; Li, E.Q.; Thoraval, Marie-Jean; Thoroddsen, S.T.

2015-01-01

Drops impacting at low velocities onto a pool surface can stretch out thin hemispherical sheets of air between the drop and the pool. These air sheets can remain intact until they reach submicron thicknesses, at which point they rupture to form a myriad of microbubbles. By impacting a

NOAA Weather Radio - Using NWR SAME

Science.gov (United States)

Non-Zero All Hazards Logo Emergency Alert Description Event Codes Fact Sheet FAQ Organization Search also used in the Emergency Alert System (EAS). See EAS fact sheet for more information. Using SAME uniquely describes each county. For coding of a whole county, the first digit is zero. For coding of a part

Strategy for Promoting the Equitable Development of Basic Education in Underdeveloped Counties as Seen from Cili County

Science.gov (United States)

Shihua, Peng; Rihui, Tan

2009-01-01

Employing statistical analysis, this study has made a preliminary exploration of promoting the equitable development of basic education in underdeveloped counties through the case study of Cili county. The unequally developed basic education in the county has been made clear, the reasons for the inequitable education have been analyzed, and,…

Reducing Test Anxiety while Increasing Learning: The Cheat Sheet

Science.gov (United States)

Erbe, Brigitte

2007-01-01

Student learning is greatly enhanced by studying prior to an exam. Allowing students to prepare a cheat sheet for the exam helps structure this study time and deepens learning. The crib sheet is well defined: one double-sided page of notes. An award for the best and most creative cheat sheet allows the instructor to appreciate the students'…

Ice sheet hydrology from observations

Energy Technology Data Exchange (ETDEWEB)

Jansson, Peter [Dept. of Physical Geography and Quaternary Geology, Stockholm Univ-, Stockholm (Sweden)

2010-11-15

The hydrological systems of ice sheets are complex. Our view of the system is split, largely due to the complexity of observing the systems. Our basic knowledge of processes have been obtained from smaller glaciers and although applicable in general to the larger scales of the ice sheets, ice sheets contain features not observable on smaller glaciers due to their size. The generation of water on the ice sheet surface is well understood and can be satisfactorily modeled. The routing of water from the surface down through the ice is not complicated in terms of procat has been problematic is the way in which the couplings between surface and bed has been accomplished through a kilometer of cold ice, but with the studies on crack propagation and lake drainage on Greenland we are beginning to understand also this process and we know water can be routed through thick cold ice. Water generation at the bed is also well understood but the main problem preventing realistic estimates of water generation is lack of detailed information about geothermal heat fluxes and their geographical distribution beneath the ice. Although some average value for geothermal heat flux may suffice, for many purposes it is important that such values are not applied to sub-regions of significantly higher fluxes. Water generated by geothermal heat constitutes a constant supply and will likely maintain a steady system beneath the ice sheet. Such a system may include subglacial lakes as steady features and reconfiguration of the system is tied to time scales on which the ice sheet geometry changes so as to change pressure gradients in the basal system itself. Large scale re-organization of subglacial drainage systems have been observed beneath ice streams. The stability of an entirely subglacially fed drainage system may hence be perturbed by rapid ice flow. In the case of Antarctic ice streams where such behavior has been observed, the ice streams are underlain by deformable sediments. It is

Ice sheet hydrology from observations

International Nuclear Information System (INIS)

Jansson, Peter

2010-11-01

The hydrological systems of ice sheets are complex. Our view of the system is split, largely due to the complexity of observing the systems. Our basic knowledge of processes have been obtained from smaller glaciers and although applicable in general to the larger scales of the ice sheets, ice sheets contain features not observable on smaller glaciers due to their size. The generation of water on the ice sheet surface is well understood and can be satisfactorily modeled. The routing of water from the surface down through the ice is not complicated in terms of procat has been problematic is the way in which the couplings between surface and bed has been accomplished through a kilometer of cold ice, but with the studies on crack propagation and lake drainage on Greenland we are beginning to understand also this process and we know water can be routed through thick cold ice. Water generation at the bed is also well understood but the main problem preventing realistic estimates of water generation is lack of detailed information about geothermal heat fluxes and their geographical distribution beneath the ice. Although some average value for geothermal heat flux may suffice, for many purposes it is important that such values are not applied to sub-regions of significantly higher fluxes. Water generated by geothermal heat constitutes a constant supply and will likely maintain a steady system beneath the ice sheet. Such a system may include subglacial lakes as steady features and reconfiguration of the system is tied to time scales on which the ice sheet geometry changes so as to change pressure gradients in the basal system itself. Large scale re-organization of subglacial drainage systems have been observed beneath ice streams. The stability of an entirely subglacially fed drainage system may hence be perturbed by rapid ice flow. In the case of Antarctic ice streams where such behavior has been observed, the ice streams are underlain by deformable sediments. It is

Curry County E-911 Roads

Data.gov (United States)

Earth Data Analysis Center, University of New Mexico — Line attributes denoting all street centerlines in Curry County. Dataset includes all centerlines for all county maintained roads, all state and federal highways,and...

Allegheny County Land Use Areas

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — Allegheny County land use as ascribed to areas of land. The Land Use Feature Dataset contains photogrammetrically compiled information concerning vegetation and...

Laser Indirect Shock Welding of Fine Wire to Metal Sheet.

Science.gov (United States)

Wang, Xiao; Huang, Tao; Luo, Yapeng; Liu, Huixia

2017-09-12

The purpose of this paper is to present an advanced method for welding fine wire to metal sheet, namely laser indirect shock welding (LISW). This process uses silica gel as driver sheet to accelerate the metal sheet toward the wire to obtain metallurgical bonding. A series of experiments were implemented to validate the welding ability of Al sheet/Cu wire and Al sheet/Ag wire. It was found that the use of a driver sheet can maintain high surface quality of the metal sheet. With the increase of laser pulse energy, the bonding area of the sheet/wire increased and the welding interfaces were nearly flat. Energy dispersive spectroscopy (EDS) results show that the intermetallic phases were absent and a short element diffusion layer which would limit the formation of the intermetallic phases emerging at the welding interface. A tensile shear test was used to measure the mechanical strength of the welding joints. The influence of laser pulse energy on the tensile failure modes was investigated, and two failure modes, including interfacial failure and failure through the wire, were observed. The nanoindentation test results indicate that as the distance to the welding interface decreased, the microhardness increased due to the plastic deformation becoming more violent.

Large patternable metal nanoparticle sheets by photo/e-beam lithography

Science.gov (United States)

Saito, Noboru; Wang, Pangpang; Okamoto, Koichi; Ryuzaki, Sou; Tamada, Kaoru

2017-10-01

Techniques for micro/nano-scale patterning of large metal nanoparticle sheets can potentially be used to realize high-performance photoelectronic devices because the sheets provide greatly enhanced electrical fields around the nanoparticles due to localized surface plasmon resonances. However, no single metal nanoparticle sheet currently exists with sufficient durability for conventional lithographical processes. Here, we report large photo and/or e-beam lithographic patternable metal nanoparticle sheets with improved durability by incorporating molecular cross-linked structures between nanoparticles. The cross-linked structures were easily formed by a one-step chemical reaction; immersing a single nanoparticle sheet consisting of core metals, to which capping molecules ionically bond, in a dithiol ethanol solution. The ligand exchange reaction processes were discussed in detail, and we demonstrated 20 μm wide line and space patterns, and a 170 nm wide line of the silver nanoparticle sheets.

Optimal Design of Sheet Pile Wall Embedded in Clay

Science.gov (United States)

Das, Manas Ranjan; Das, Sarat Kumar

2015-09-01

Sheet pile wall is a type of flexible earth retaining structure used in waterfront offshore structures, river protection work and temporary supports in foundations and excavations. Economy is an essential part of a good engineering design and needs to be considered explicitly in obtaining an optimum section. By considering appropriate embedment depth and sheet pile section it may be possible to achieve better economy. This paper describes optimum design of both cantilever and anchored sheet pile wall penetrating clay using a simple optimization tool Microsoft Excel ® Solver. The detail methodology and its application with examples are presented for cantilever and anchored sheet piles. The effects of soil properties, depth of penetration and variation of ground water table on the optimum design are also discussed. Such a study will help professional while designing the sheet pile wall penetrating clay.

2007 Lake County Board of County Commissioners Topographic LiDAR: Lake County, Florida

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — This metadata document describes the LiDAR point data in LAS format produced by Kucera covering the project area of Lake County, FL. The data produced is...

Allegheny County School District Boundaries

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — This dataset demarcates the school district boundaries within Allegheny County If viewing this description on the Western Pennsylvania Regional Data Center’s open...

How might the North American ice sheet influence the northwestern Eurasian climate?

Science.gov (United States)

Beghin, P.; Charbit, S.; Dumas, C.; Kageyama, M.; Ritz, C.

2015-10-01

It is now widely acknowledged that past Northern Hemisphere ice sheets covering Canada and northern Europe at the Last Glacial Maximum (LGM) exerted a strong influence on climate by causing changes in atmospheric and oceanic circulations. In turn, these changes may have impacted the development of the ice sheets themselves through a combination of different feedback mechanisms. The present study is designed to investigate the potential impact of the North American ice sheet on the surface mass balance (SMB) of the Eurasian ice sheet driven by simulated changes in the past glacial atmospheric circulation. Using the LMDZ5 atmospheric circulation model, we carried out 12 experiments under constant LGM conditions for insolation, greenhouse gases and ocean. In these experiments, the Eurasian ice sheet is removed. The 12 experiments differ in the North American ice-sheet topography, ranging from a white and flat (present-day topography) ice sheet to a full-size LGM ice sheet. This experimental design allows the albedo and the topographic impacts of the North American ice sheet onto the climate to be disentangled. The results are compared to our baseline experiment where both the North American and the Eurasian ice sheets have been removed. In summer, the sole albedo effect of the American ice sheet modifies the pattern of planetary waves with respect to the no-ice-sheet case, resulting in a cooling of the northwestern Eurasian region. By contrast, the atmospheric circulation changes induced by the topography of the North American ice sheet lead to a strong decrease of this cooling. In winter, the Scandinavian and the Barents-Kara regions respond differently to the American ice-sheet albedo effect: in response to atmospheric circulation changes, Scandinavia becomes warmer and total precipitation is more abundant, whereas the Barents-Kara area becomes cooler with a decrease of convective processes, causing a decrease of total precipitation. The gradual increase of the

Statement of Kenneth E. Yager, County Executive, Roane County, TN

International Nuclear Information System (INIS)

Anon.

1987-01-01

I am Ken Yager, I am the county executive for Roane County, TN which is the preferred site for the proposed Monitored Retrieval Storage facility, or the MRS. and I am submitting into the record additional written testimony which was written largely by the Honorable Robert Peele, who is sitting here, who is a member of the Roane County Board of Commissioners, our local legislative body. The premise of my remarks is that the Department of Energy proposal for the MRS in our county in unacceptable unless the Congress and the Department of Energy are to be willing partners with the local communities. Our considerations have been limited to: one, can an MRS be operated safely, and if so under what conditions; and what would be the impacts of the facility and how might they be mitigated. Our recommendations on those two points lead me to my earlier comment about being partners with the Congress, because our recommendations can be summed up simply, Mr. Chairman, as local control. We are exceedingly concerned about the prospect of being trapped in a national squeeze play, caught between a recognized need for a way to deal with nuclear waste and intense political efforts to put that problem in somebody else's back yard. And if we are to be that back yard, we would ask that the Congress and the Department of Energy recognize our stake in this national effort. We must have an equal role in the process

Breakup characteristics of power-law liquid sheets formed by two impinging jets

International Nuclear Information System (INIS)

Bai, Fuqiang; Diao, Hai; Chang, Qing; Wang, Endong; Du, Qing; Zhang, Mengzheng

2014-01-01

The breakup characteristics of the shear-thinning power-law liquid sheets formed by two impinging jets have been investigated with the shadowgraph technique. This paper focuses on the effects of spray parameters (jet velocity), physical parameters (viscosity) and geometry parameters (impinging angle and nozzle cross-sectional shape) on the breakup behaviors of liquid sheets. The breakup mode, sheet length and expansion angle of the sheet are extracted from the spray images obtained by a high speed camera. Impinging angle and Weber number play the similar roles in promoting the breakup of liquid sheets. With the increase of jet velocity, five different breakup modes are observed and the expansion angle increases consistently after the closed-rim mode while the sheet length first increases and then decreases. But there exists a concave consisting of a fierce drop and a second rising process on the sheet length curve for the fluid with smaller viscosity. Different nozzle cross-sectional shapes emphasize significant effects on the sheet length and expansion angle of liquid sheets. At a fixed Weber number, the liquid sheet with greater viscosity has a greater sheet length and a smaller expansion angle due to the damping effect of viscosity. (papers)

Fatigue analysis of a PWR steam generator tube sheet

International Nuclear Information System (INIS)

Billon, F.; Buchalet, C.; Poudroux, G.

1985-01-01

The fatigue analysis of a PWR steam generator (S.G) tube sheet is threefold. First, the flow, pressure and temperature variations during the design transients are defined for both the primary fluid and the normal and auxiliary feedwater. Second, the flow, velocities, pressure and temperature variations of the secondary fluid at the bottom of the downcomer and above the tube sheet are determined for the transients considered. Finally, the corresponding temperatures and stresses in the tube sheet are calculated and the usage factors determined at various locations in the tube sheet. The currently available standard design transients for the primary fluid and the feedwater are too conservative to be utilized as such in the fatigue analysis of the S.G. tube sheets. Thus, a detailed examination and reappraisal of each operating transient was performed. The revised design conditions are used as inputs to the calculation model TEMPTRON. TEMPTRON determines the mixing conditions between the feedwater and the recirculation fluid from the S.G. feedwater nozzles to the center of the tube sheet via the downcomer. The fluid parameters, flow rate and velocity, temperature and pressure variations, as a function of the time during the transients are obtained. Finally, the usage factors at various locations on the tube sheet are derived using the standard ASME section III method

Grounding line transient response in marine ice sheet models

Directory of Open Access Journals (Sweden)

A. S. Drouet

2013-03-01

Full Text Available Marine ice-sheet stability is mostly controlled by the dynamics of the grounding line, i.e. the junction between the grounded ice sheet and the floating ice shelf. Grounding line migration has been investigated within the framework of MISMIP (Marine Ice Sheet Model Intercomparison Project, which mainly aimed at investigating steady state solutions. Here we focus on transient behaviour, executing short-term simulations (200 yr of a steady ice sheet perturbed by the release of the buttressing restraint exerted by the ice shelf on the grounded ice upstream. The transient grounding line behaviour of four different flowline ice-sheet models has been compared. The models differ in the physics implemented (full Stokes and shallow shelf approximation, the numerical approach, as well as the grounding line treatment. Their overall response to the loss of buttressing is found to be broadly consistent in terms of grounding line position, rate of surface elevation change and surface velocity. However, still small differences appear for these latter variables, and they can lead to large discrepancies (> 100% observed in terms of ice sheet contribution to sea level when cumulated over time. Despite the recent important improvements of marine ice-sheet models in their ability to compute steady state configurations, our results question the capacity of these models to compute short-term reliable sea-level rise projections.

A laser sheet self-calibration method for scanning PIV

Science.gov (United States)

Knutsen, Anna N.; Lawson, John M.; Dawson, James R.; Worth, Nicholas A.

2017-10-01

Knowledge of laser sheet position, orientation, and thickness is a fundamental requirement of scanning PIV and other laser-scanning methods. This paper describes the development and evaluation of a new laser sheet self-calibration method for stereoscopic scanning PIV, which allows the measurement of these properties from particle images themselves. The approach is to fit a laser sheet model by treating particles as randomly distributed probes of the laser sheet profile, whose position is obtained via a triangulation procedure enhanced by matching particle images according to their variation in brightness over a scan. Numerical simulations and tests with experimental data were used to quantify the sensitivity of the method to typical experimental error sources and validate its performance in practice. The numerical simulations demonstrate the accurate recovery of the laser sheet parameters over range of different seeding densities and sheet thicknesses. Furthermore, they show that the method is robust to significant image noise and camera misalignment. Tests with experimental data confirm that the laser sheet model can be accurately reconstructed with no impairment to PIV measurement accuracy. The new method is more efficient and robust in comparison with the standard (self-) calibration approach, which requires an involved, separate calibration step that is sensitive to experimental misalignments. The method significantly improves the practicality of making accurate scanning PIV measurements and broadens its potential applicability to scanning systems with significant vibrations.

16 CFR 460.15 - How installers must handle fact sheets.

Science.gov (United States)

2010-01-01

... ADVERTISING OF HOME INSULATION § 460.15 How installers must handle fact sheets. If you are an installer, you... from you, you must show them the fact sheet(s) for the type(s) of insulation they want. You can decide...

The aerogel threshold Cherenkov detector for the high momentum spectrometer in Hall C at Jefferson lab

International Nuclear Information System (INIS)

Razmik Asaturyan; Rolf Ent; Howard Fenker; David Gaskell; Garth Huber; Mark Jones; David Mack; Hamlet Mkrtchyan; Bert Metzger; Nadia Novikoff; Vardan Tadevosyan; William Vulcan; Stephen Wood

2004-01-01

We describe a new aerogel threshold Cherenkov detector installed in the HMS spectrometer in Hall C at Jefferson Lab. The Hall C experimental program in 2003 required an improved particle identification system for better identification of π/K/p, which was achieved by installing an additional threshold Cherenkov counter. Two types of aerogel with n = 1.03 and n = 1.015 allow one to reach ∼10 -3 proton and 10 -2 kaon rejection in the 1-5 GeV/c momentum range with pion detection efficiency better than 99% (97%). The detector response shows no significant position dependence due to a diffuse light collection technique. The diffusion box was equipped with 16 Photonis XP4572 PMT's. The mean number of photoelectrons in saturation was ∼16 and ∼8, respectively. Moderate particle identification is feasible near threshold

Allegheny County-Owned Roads Centerlines

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — This dataset shows the roads owned by Allegheny County. If viewing this description on the Western Pennsylvania Regional Data Center’s open data portal...

Allegheny County Fast Food Establishments

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — The Allegheny County Health Department has generated this list of fast food restaurants by exporting all chain restaurants without an alcohol permit from the...

Ice sheets on plastically-yielding beds

Science.gov (United States)

Hewitt, Ian

2016-11-01

Many fast flowing regions of ice sheets are underlain by a layer of water-saturated sediments, or till. The rheology of the till has been the subject of some controversy, with laboratory tests suggesting almost perfectly plastic behaviour (stress independent of strain rate), but many models adopting a pseudo-viscous description. In this work, we consider the behaviour of glaciers underlain by a plastic bed. The ice is treated as a viscous gravity current, on a bed that allows unconstrained slip above a critical yield stress. This simplified description allows rapid sliding, and aims to investigate 'worst-case' scenarios of possible ice-sheet disintegration. The plastic bed results in an approximate ice-sheet geometry that is primarily controlled by force balance, whilst ice velocity is determined from mass conservation (rather than the other way around, as standard models would hold). The stability of various states is considered, and particular attention is given to the pace at which transitions between unstable states can occur. Finally, we observe that the strength of basal tills depends strongly on pore pressure, and combine the model with a description of subglacial hydrology. Implications for the present-day ice sheets in Greenland and Antarctica will be discussed. Funding: ERC Marie Curie FP7 Career Integration Grant.

Pseudomonas - Fact Sheet

OpenAIRE

Public Health Agency

2012-01-01

Fact sheet on Pseudomonas, including:What is Pseudomonas?What infections does it cause?Who is susceptible to pseudomonas infection?How will I know if I have pseudomonas infection?How can Pseudomonas be prevented from spreading?How can I protect myself from Pseudomonas?How is Pseudomonas infection treated?

Performance Testing of Jefferson Lab 12 GeV Helium Screw Compressors

Science.gov (United States)

Knudsen, P.; Ganni, V.; Dixon, K.; Norton, R.; Creel, J.

2015-08-01

Oil injected screw compressors have essentially superseded all other types of compressors in modern helium refrigeration systems due to their large displacement capacity, reliability, minimal vibration, and capability of handling helium's high heat of compression. At the present state of compressor system designs for helium refrigeration systems, typically two-thirds of the lost input power is due to the compression system. It is important to understand the isothermal and volumetric efficiencies of these machines to help properly design the compression system to match the refrigeration process. It is also important to identify those primary compressor skid exergetic loss mechanisms which may be reduced, thereby offering the possibility of significantly reducing the input power to helium refrigeration processes which are extremely energy intensive. This paper summarizes the results collected during the commissioning of the new compressor system for Jefferson Lab's (JLab's) 12 GeV upgrade. The compressor skid packages were designed by JLab and built to print by industry. They incorporate a number of modifications not typical of helium screw compressor packages and most importantly allow a very wide range of operation so that JLab's patented Floating Pressure Process can be fully utilized. This paper also summarizes key features of the skid design that allow this process and facilitate the maintenance and reliability of these helium compressor systems.

Wide Area Recovery and Resiliency Program (WARRP) Knowledge Enhancement Events: CBR Workshop After Action Report

Science.gov (United States)

2012-01-01

National Guard Graham Richard EPA Region VIII Greenwalt Robert Lawrence Livermore National Laboratory Hard Dave Colorado Department of Emergency...Jefferson County Office of Emergency Management Smedley Chuck Denver Public Health Stein Steve Pacific Northwest National Laboratory Steinhour LeeAnn...Laboratory Brooke Buddemeier brooke2@llnl.gov Chris Campbell campbell48@llnl.gov Robert Greenwalt greenwalt1@llnl.gov Wilthea Hibbard hibbard3