Monitoring of the Irradiated Neutron Fluence in the Neutron Transmutation Doping Process of Hanaro

Science.gov (United States)

Kim, Myong-Seop; Park, Sang-Jun

2009-08-01

Neutron transmutation doping (NTD) for silicon is a process of the creation of phosphorus impurities in intrinsic or extrinsic silicon by neutron irradiation to obtain silicon semiconductors with extremely uniform dopant distribution. HANARO has two vertical holes for the NTD, and the irradiation for 5 and 6 inch silicon ingots has been going on at one hole. In order to achieve the accurate neutron fluence corresponding to the target resistivity, the real time neutron flux is monitored by self-powered neutron detectors. After irradiation, the total irradiation fluence is confirmed by measuring the absolute activity of activation detectors. In this work, a neutron fluence monitoring method using zirconium foils with the mass of 10 ~ 50 mg was applied to the NTD process of HANARO. We determined the proportional constant of the relationship between the resistivity of the irradiated silicon and the neutron fluence determined by using zirconium foils. The determined constant for the initially n-type silicon was 3.126 × 1019 n·Ω/cm. It was confirmed that the difference between this empirical value and the theoretical one was only 0.5%. Conclusively, the practical methodology to perform the neutron transmutation doping of silicon was established.

A study for optimal transmutation system

International Nuclear Information System (INIS)

Park, W.S.; Song, T.Y.; Shin, H.S.; Park, C.K.

1996-01-01

Couple of transmutation systems are being under investigation to design the optimal transmutation device. Several basic studies were performed for that objectives: (1) select the radioactive nuclides to be transmuted: (2) investigate the physical characteristics of each nuclide; (3) study the most favorable neutron energy environment for the transmutation. The existing LWR and LMFBR cores were found to be not a satisfiable ones in terms of transmutation rate itself. (author). 5 refs, 2 figs, 3 tabs

Effect of Fast Neutron to MA/PU Burning/Transmutation Characteristic Using a Fast Reactor

International Nuclear Information System (INIS)

Marsodi; Lasman, As Natio; Kimamoto, A.; Marsongkohadi; Zaki, S.

2003-01-01

MA/Pu burning/transmutation has been studied and evaluated using fast neutrons. Generally, neutron density at this fast burner reactor and transmutation has spectrum energy level around 0.2 MeV with wide enough variation, i.e. from low neutron spectrum to its peak is 0.2 MeV. This neutron spectrum energy level depends on the kind of cooler material or fuel used. Neutron spectrum higher than fast power reactor neutron spectrum is found by means of changing oxide fuel by metallic fuel and changing natrium cooler material by metallic or gas cooler material. This evaluation is conducted by various variations in accordance with the kind of fuel or cooler, MA/Pu fractions and fuel comparison fraction with respect to its cooler in order to get better neutron usage and MA/Pu burning speed. Reactor calculation evaluation in this paper was conducted with 26-group nuclear data cross section energy spectrum. The main purpose of the discussion is to know the effect of fast neutrons to burning/transmutation MA/Pu using fast neutrons

Accelerator-driven transmutation of spent fuel elements

Science.gov (United States)

Venneri, Francesco; Williamson, Mark A.; Li, Ning

2002-01-01

An apparatus and method is described for transmuting higher actinides, plutonium and selected fission products in a liquid-fuel subcritical assembly. Uranium may also be enriched, thereby providing new fuel for use in conventional nuclear power plants. An accelerator provides the additional neutrons required to perform the processes. The size of the accelerator needed to complete fuel cycle closure depends on the neutron efficiency of the supported reactors and on the neutron spectrum of the actinide transmutation apparatus. Treatment of spent fuel from light water reactors (LWRs) using uranium-based fuel will require the largest accelerator power, whereas neutron-efficient high temperature gas reactors (HTGRs) or CANDU reactors will require the smallest accelerator power, especially if thorium is introduced into the newly generated fuel according to the teachings of the present invention. Fast spectrum actinide transmutation apparatus (based on liquid-metal fuel) will take full advantage of the accelerator-produced source neutrons and provide maximum utilization of the actinide-generated fission neutrons. However, near-thermal transmutation apparatus will require lower standing

Neutron-transmuted carbon-14 in neutron-irradiated GaN: Compensation of DX-like center

International Nuclear Information System (INIS)

Ida, T.; Oga, T.; Kuriyama, K.; Kushida, K.; Xu, Q.; Fukutani, S.

2013-01-01

The transmuted-C related luminescence and net carrier concentration are studied by combining photoluminescence, liquid scintillation, and Raman scattering. GaN single crystal films grown by metalorganic-vapor-phase epitaxy are irradiated with fast and thermal neutrons at fluxes of 3.9 × 10 13 cm −2 s −1 and 8.15 × 10 13 cm −2 s −1 , respectively. Irradiation time is 48 hours. The calculated 72 Ge and 14 C concentrations are 1.24 × 10 18 cm −3 and 1.13 × 10 18 cm −3 , respectively. The transmuted 14 C is detected by the liquid scintillation method to survey β-rays emitted in the process of 14 C decays from 14 N. Tritium ( 3 H) is also emitted by a (n,t) reaction of 14 N due to the neutron irradiation above 4.5 MeV. Photoluminescence relating to C, DX-like center of Ge and yellow luminescence band are observed in 1000 °C annealed NTD-GaN. The free electron concentration estimated from Raman scattering is 4.97 × 10 17 cm −3 . This value is lower than that from the transmuted Ge concentration, suggesting the compensation due to the transmuted 14 C acceptors

Transmutation of Americium in Fast Neutron Facilities

International Nuclear Information System (INIS)

Zhang, Youpeng

2011-01-01

In this thesis, the feasibility to use a medium sized sodium cooled fast reactor fully loaded with MOX fuel for efficient transmutation of americium is investigated by simulating the safety performance of a BN600-type fast reactor loaded with different fractions of americium in the fuel, using the safety parameters obtained with the SERPENT Monte Carlo code. The focus is on americium mainly due to its long-term contribution to the radiotoxicity of spent nuclear fuel and its deterioration on core's safety parameters. Applying the SAS4A/SASSYS transient analysis code, it is demonstrated that the power rating needs to be reduced by 6% for each percent additional americium introduction into the reference MOX fuel, maintaining 100 K margin to fuel melting, which is the most limiting failure mechanism. Safety analysis of a new Accelerator Driven System design with a smaller pin pitch-to-diameter ratio comparing to the reference EFIT-400 design, aiming at improving neutron source efficiency, was also performed by simulating performance for unprotected loss of flow, unprotected transient overpower, and protected loss-of-heat-sink transients, using neutronic parameters obtained from MCNP calculations. Thanks to the introduction of the austenitic 15/15Ti stainless steel with enhanced creep rupture resistance and acceptable irradiation swelling rate, the suggested ADS design loaded with nitride fuel and cooled by lead-bismuth eutectic could survive the full set of transients, preserving a margin of 130 K to cladding rupture during the most limiting transient. The thesis concludes that efficient transmutation of americium in a medium sized sodium cooled fast reactor loaded with MOX fuel is possible but leads to a severe power penalty. Instead, preserving transmutation rates of minor actinides up to 42 kg/TWh th , the suggested ADS design with enhanced proton source efficiency appears like a better option for americium transmutation

Evaluation of the transmutation of transuranic using neutrons spectrum from the spallation reaction

Energy Technology Data Exchange (ETDEWEB)

Gilberti, Mauricio; Pereira, Claubia, E-mail: mgilber@eletronuclear.gov.br [Eletrobras Termonuclear S.A. (ELETRONUCLEAR), Angra dos Reis, RJ (Brazil); Veloso, Maria A. Fortini, E-mail: claubia@nuclear.ufmg.br [Universidade Federal de Minas Gerais (UFMG), Belo Horizante, MG (Brazil). Dept. de Engenharia Nuclear

2013-07-01

The transmutation of transuranic was analyzed by simulating the neutron flux from different spallation sources across arrays of fissile material with isotopic composition PWR reprocessing. A simplified model of Accelerator-Driven Systems (ADS) containing target, moderator graphite, lead-bismuth coolant or sodium coolant, is used. The simulation was made using the particles transport code MCNPX 2.6.0 which allowed to evaluate the rate of transmutation of actinides (Np, Pu, Am, and Cm) at different locations in the system. The objective of the study is to evaluate which the behavior and influences the spectrum of the spallation in the transmutation without the contribution or interference of multiplier, medium subcritical, which would add the contribution of fission neutrons generated, thus interfering in the analysis. The arrangement enable to infer the influence of hardened neutron flux from the spallation reaction in the transmutation, the results show that this is independent of the target material chosen, and the spectrum of spallation has a negligible importance compared to the influence of moderation and scattering generated by the coolant or moderator used. (author)

Evaluation of the transmutation of transuranic using neutrons spectrum from the spallation reaction

International Nuclear Information System (INIS)

Gilberti, Mauricio; Pereira, Claubia; Veloso, Maria A. Fortini

2013-01-01

The transmutation of transuranic was analyzed by simulating the neutron flux from different spallation sources across arrays of fissile material with isotopic composition PWR reprocessing. A simplified model of Accelerator-Driven Systems (ADS) containing target, moderator graphite, lead-bismuth coolant or sodium coolant, is used. The simulation was made using the particles transport code MCNPX 2.6.0 which allowed to evaluate the rate of transmutation of actinides (Np, Pu, Am, and Cm) at different locations in the system. The objective of the study is to evaluate which the behavior and influences the spectrum of the spallation in the transmutation without the contribution or interference of multiplier, medium subcritical, which would add the contribution of fission neutrons generated, thus interfering in the analysis. The arrangement enable to infer the influence of hardened neutron flux from the spallation reaction in the transmutation, the results show that this is independent of the target material chosen, and the spectrum of spallation has a negligible importance compared to the influence of moderation and scattering generated by the coolant or moderator used. (author)

The development of the market for neutron transmutation doped silicon

International Nuclear Information System (INIS)

Herzer, H.; Vieweg-Gutberlet, G.

1984-01-01

Neutron transmutation doped silicon was introduced to the electronic device market in the 1975-1976 time period. Today, neutron transmutation doping is definitely a mature technology applied mainly to semiconductor power devices. There is no doubt that the power device sector will remain the major consumer of NTD silicon in the near future. This paper examines the possible application of NTD silicon to other areas of the semiconductor market, and concludes that the need for NTD silicon will continue to grow and will expand into other applications. Consequently, unless new reactor capacities become available by the end of the decade, NTD silicon applications will probably be limited mainly to power and sensor devices

Neutronic evaluation of insertion of a transmutation layer in a Tokamak system

International Nuclear Information System (INIS)

Cabrera, Carlos Eduardo Velasquez

2013-01-01

Using MCNP5 code were simulated different models representing the ITER system. It was evaluated the two alloys used by the first wall under high neutron flux. The neutron flux and the reaction rate along the different walls were obtained and evaluated. Based on the results, it was possible to conclude the best way to represent the fusion device evaluating; the different geometrical models, the best material to be used in the first wall taking into consideration the objective of transmutation and placed the transmutation layer. (author)

Transmutation detectors

Energy Technology Data Exchange (ETDEWEB)

Viererbl, L., E-mail: vie@ujv.c [Research Centre Rez Ltd. (Czech Republic); Nuclear Research Institute Rez plc (Czech Republic); Lahodova, Z. [Research Centre Rez Ltd. (Czech Republic); Nuclear Research Institute Rez plc (Czech Republic); Klupak, V. [Nuclear Research Institute Rez plc (Czech Republic); Sus, F. [Research Centre Rez Ltd. (Czech Republic); Nuclear Research Institute Rez plc (Czech Republic); Kucera, J. [Research Centre Rez Ltd. (Czech Republic); Nuclear Physics Institute, Academy of Sciences of the Czech Republic (Czech Republic); Kus, P.; Marek, M. [Research Centre Rez Ltd. (Czech Republic); Nuclear Research Institute Rez plc (Czech Republic)

2011-03-11

We have designed a new type of detectors, called transmutation detectors, which can be used primarily for neutron fluence measurement. The transmutation detector method differs from the commonly used activation detector method in evaluation of detector response after irradiation. Instead of radionuclide activity measurement using radiometric methods, the concentration of stable non-gaseous nuclides generated by transmutation in the detector is measured using analytical methods like mass spectrometry. Prospective elements and nuclear reactions for transmutation detectors are listed and initial experimental results are given. The transmutation detector method could be used primarily for long-term measurement of neutron fluence in fission nuclear reactors, but in principle it could be used for any type of radiation that can cause transmutation of nuclides in detectors. This method could also be used for measurement in accelerators or fusion reactors.

Transmutation detectors

International Nuclear Information System (INIS)

Viererbl, L.; Lahodova, Z.; Klupak, V.; Sus, F.; Kucera, J.; Kus, P.; Marek, M.

2011-01-01

We have designed a new type of detectors, called transmutation detectors, which can be used primarily for neutron fluence measurement. The transmutation detector method differs from the commonly used activation detector method in evaluation of detector response after irradiation. Instead of radionuclide activity measurement using radiometric methods, the concentration of stable non-gaseous nuclides generated by transmutation in the detector is measured using analytical methods like mass spectrometry. Prospective elements and nuclear reactions for transmutation detectors are listed and initial experimental results are given. The transmutation detector method could be used primarily for long-term measurement of neutron fluence in fission nuclear reactors, but in principle it could be used for any type of radiation that can cause transmutation of nuclides in detectors. This method could also be used for measurement in accelerators or fusion reactors.

Detecting neutrons by forward recoil protons at the Energy & Transmutation facility: Detector development and calibration with 14.1-MeV neutrons

Science.gov (United States)

Afanasev, S.; Vishnevskiy, A.; Vishnevskiy, D.; Rogachev, A.; Tyutyunnikov, S.

2017-05-01

As part of the Energy & Transmutation project, we are developing a detector for neutrons with energies in the 10-100 MeV range emitted from the target irradiated by a charged-particle beam. The neutron is detected by measuring the time-of-flight and total kinetic energy of the forward-going recoil proton [1] knocked out at a small angle from a thin layer of plastic scintillator, which has to be selected against an intense background created by γ quanta, scattered neutrons, and charged particles. On the other hand, neutron energy has to be measured over the full range with no extra tuning of the detector operation regime. Initial measurements with a source of 14.1-MeV neutrons are reported.

Development of neutron-transmutation-doped germanium bolometer material

International Nuclear Information System (INIS)

Palaio, N.P.

1983-08-01

The behavior of lattice defects generated as a result of the neutron-transmutation-doping of germanium was studied as a function of annealing conditions using deep level transient spectroscopy (DLTS) and mobility measurements. DLTS and variable temperature Hall effect were also used to measure the activation of dopant impurities formed during the transmutation process. In additioon, a semi-automated method of attaching wires on to small chips of germanium ( 3 ) for the fabrication of infrared detecting bolometers was developed. Finally, several different types of junction field effect transistors were tested for noise at room and low temperature (approx. 80 K) in order to find the optimum device available for first stage electronics in the bolometer signal amplification circuit

The cross sections of reactions resulting in transmutation of long-lived radionuclides of exhausted nuclear fuel exposed to fast neutrons

International Nuclear Information System (INIS)

Konodeev, A.Yu.; Korovin, Yu.A.; Erview, K.

1993-01-01

Research is at present concerned with the possible transmutation of long-lived radionuclides of spent nuclear fuel in the flux of fast neutrons from neutron generators which are distinguished by their energy spectrum and density of the flux generated. For this purpose one must know the cross sections of the nuclear reactions resulting in the transmutation and formation of new long-lived radionuclides due to the irradiation. The transmutation rate of radioisotope irradiated with neutrons have a known energy spectrum is determined by calculating the transmutation cross section which is equal to the sum of the cross sections of neutron reactions causing conversion of a particular isotope into another after the decay of short-lived residual nuclei. The presently available neutron cross section data of long-lived radionuclides, i.e., the products of the fission of nuclear fuel, are insufficient for research on these effects as transmutations occur in a flux of high-energy neutrons. This paper presents the cross sections of reactions accounting for the transmutation of the most important long-lived radionuclides of exhausted nuclear fuel during its irradiation with neutron having energies of up to 100 MeV. The neutron cross sections were calculated for 79 Se, 90 Sr, 93 Zr, 99 Tc, 107 Pd, 126 Sn, 129 I, 135 Cs and 137 Cs with a half-life ≥30 years

Application of neutron transmutation doping method to initially p-type silicon material.

Science.gov (United States)

Kim, Myong-Seop; Kang, Ki-Doo; Park, Sang-Jun

2009-01-01

The neutron transmutation doping (NTD) method was applied to the initially p-type silicon in order to extend the NTD applications at HANARO. The relationship between the irradiation neutron fluence and the final resistivity of the initially p-type silicon material was investigated. The proportional constant between the neutron fluence and the resistivity was determined to be 2.3473x10(19)nOmegacm(-1). The deviation of the final resistivity from the target for almost all the irradiation results of the initially p-type silicon ingots was at a range from -5% to 2%. In addition, the burn-up effect of the boron impurities, the residual (32)P activity and the effect of the compensation characteristics for the initially p-type silicon were studied. Conclusively, the practical methodology to perform the neutron transmutation doping of the initially p-type silicon ingot was established.

Neutron data for accelerator-driven transmutation technologies. Annual Report 2004/2005

International Nuclear Information System (INIS)

Blomgren, J.; Nilsson, L.; Mermod, P.; Olsson, N.; Pomp, S.; Oehrn, A.; Oesterlund, M.

2005-09-01

The project NATT, Neutron data for Accelerator-driven Transmutation Technology, is performed within the nuclear reactions group of the Dept. of Neutron Research, Uppsala univ. The activities of the group are directed towards experimental studies of nuclear reaction probabilities of importance for various applications, like transmutation of nuclear waste, biomedical effects and electronics reliability. The experimental work is primarily undertaken at the The Svedberg Laboratory (TSL) in Uppsala, where the group has previously developed two world-unique instruments, MEDLEY and SCANDAL. Highlights from the past year: An article on three-body force effects has been on the top-ten downloading list of Physics Letters B. Uppsala had the largest foreign delegation at the International Conference on Nuclear Data for Science and Technology in Santa Fe, NM, USA, and presented the largest number of papers of all experimental groups. A neutron flux monitor for the new FOI neutron beam facility has been developed, commissioned and taken into regular operation. Within the project, one licentiate exam has been awarded. The new neutron beam facility at TSL has been taken into commercial operation and is now having the largest commercial turnover of all European facilities in the field

Investigation of the feasibility of a small scale transmutation device

Science.gov (United States)

Sit, Roger Carson

This dissertation presents the design and feasibility of a small-scale, fusion-based transmutation device incorporating a commercially available neutron generator. It also presents the design features necessary to optimize the device and render it practical for the transmutation of selected long-lived fission products and actinides. Four conceptual designs of a transmutation device were used to study the transformation of seven radionuclides: long-lived fission products (Tc-99 and I-129), short-lived fission products (Cs-137 and Sr-90), and selective actinides (Am-241, Pu-238, and Pu-239). These radionuclides were chosen because they are major components of spent nuclear fuel and also because they exist as legacy sources that are being stored pending a decision regarding their ultimate disposition. The four designs include the use of two different devices; a Deuterium-Deuterium (D-D) neutron generator (for one design) and a Deuterium-Tritium (D-T) neutron generator (for three designs) in configurations which provide different neutron energy spectra for targeting the radionuclide for transmutation. Key parameters analyzed include total fluence and flux requirements; transmutation effectiveness measured as irradiation effective half-life; and activation products generated along with their characteristics: activity, dose rate, decay, and ingestion and inhalation radiotoxicity. From this investigation, conclusions were drawn about the feasibility of the device, the design and technology enhancements that would be required to make transmutation practical, the most beneficial design for each radionuclide, the consequence of the transmutation, and radiation protection issues that are important for the conceptual design of the transmutation device. Key conclusions from this investigation include: (1) the transmutation of long-lived fission products and select actinides can be practical using a small-scale, fusion driven transmutation device; (2) the transmutation of long

Neutronic Analysis on Coolant Options in a Hybrid Reactor System for High Level Waste Transmutation

Energy Technology Data Exchange (ETDEWEB)

Hong, Seong Hee; Kim, Myung Hyun [Kyung Hee University, Seoul (Korea, Republic of)

2014-10-15

A fusion-fission hybrid reactor (FFHR) which is a combination of plasma fusion tokamak as a fast neutron source and a fission reactor as of fusion blanket is another potential candidate. In FFHR, fusion plasma machine can supply high neutron-rich and energetic 14.1MeV (D, T) neutrons compared to other options. Therefore it has better capability in HLW incineration. While, it has lower requirements compared to pure fusion. Much smaller-sized tokamak can be achievable in a near term because it needs relatively low plasma condition. FFHR has also higher safety potential than fast reactors just as ADSR because it is subcritical reactor system. FFHR proposed up to this time has many design concepts depending on the design purpose. FFHR may also satisfy many design requirement such as energy multiplication, tritium production, radiation shielding for magnets, fissile breeding for self-sustain ability also waste transmutation. Many types of fuel compositions and coolant options have been studied. Effect of choices for fuel and coolant was studied for the transmutation purpose FFHR by our team. In this study LiPb coolant was better than pure Li coolant both for neutron multiplication and tritium breeding. However, performance of waste transmutation was reduced with increased neutron absorption at coolant caused by tritium breeding. Also, LiPb as metal coolant has a problem of massive MHD pressure drop in coolant channels. Therefore, in a previous study, waste transmutation performance was evaluated with light water coolant option which may be a realistic choice. In this study, a neutronic analysis was done for the various coolant options with a detailed computation. One of solutions suggested is to use the pressure tubes inside of first wall and second wall In this work, performance of radioactive waste transmutation was compared with various coolant options. On the whole, keff increases with all coolants except for FLiBe, therefore required fusion power is decreased. In

Importance of delayed neutron data in transmutation system

International Nuclear Information System (INIS)

Tsujimoto, Kazufumi

1999-01-01

The accelerator-driven transmutation system has been studied at the Japan Atomic Energy Research Institute. This system is a hybrid system which consists of a high intensity accelerator, a spallation target and a subcritical core region. The subcritical core is driven by neutrons generated by spallation reaction in the target region. There is no control rod in this system, so the power is controlled only by proton beam current. The beam current to keep constant power change with effective multiplication factor of subcritical core. So, the evaluation of delayed neutron fraction which is strongly connected to the measurement of subcritical level is important factor in operation of accelerator-driven system. In this paper, important nuclides for the delayed neutron fraction of ADS will be discussed, moreover, present state of delayed neutron data in evaluated nuclear data library is presented. (author)

Apparatus for nuclear transmutation and power production using an intense accelerator-generated thermal neutron flux

Science.gov (United States)

Bowman, Charles D.

1992-01-01

Apparatus for nuclear transmutation and power production using an intense accelerator-generated thermal neutron flux. High thermal neutron fluxes generated from the action of a high power proton accelerator on a spallation target allows the efficient burn-up of higher actinide nuclear waste by a two-step process. Additionally, rapid burn-up of fission product waste for nuclides having small thermal neutron cross sections, and the practicality of small material inventories while achieving significant throughput derive from employment of such high fluxes. Several nuclear technology problems are addressed including 1. nuclear energy production without a waste stream requiring storage on a geological timescale, 2. the burn-up of defense and commercial nuclear waste, and 3. the production of defense nuclear material. The apparatus includes an accelerator, a target for neutron production surrounded by a blanket region for transmutation, a turbine for electric power production, and a chemical processing facility. In all applications, the accelerator power may be generated internally from fission and the waste produced thereby is transmuted internally so that waste management might not be required beyond the human lifespan.

Apparatus for nuclear transmutation and power production using an intense accelerator-generated thermal neutron flux

Science.gov (United States)

Bowman, C.D.

1992-11-03

Apparatus for nuclear transmutation and power production using an intense accelerator-generated thermal neutron flux. High thermal neutron fluxes generated from the action of a high power proton accelerator on a spallation target allows the efficient burn-up of higher actinide nuclear waste by a two-step process. Additionally, rapid burn-up of fission product waste for nuclides having small thermal neutron cross sections, and the practicality of small material inventories while achieving significant throughput derive from employment of such high fluxes. Several nuclear technology problems are addressed including 1. nuclear energy production without a waste stream requiring storage on a geological timescale, 2. the burn-up of defense and commercial nuclear waste, and 3. the production of defense nuclear material. The apparatus includes an accelerator, a target for neutron production surrounded by a blanket region for transmutation, a turbine for electric power production, and a chemical processing facility. In all applications, the accelerator power may be generated internally from fission and the waste produced thereby is transmuted internally so that waste management might not be required beyond the human lifespan.

Neutron data for accelerator-driven transmutation technologies. Annual Report 2003/2004

International Nuclear Information System (INIS)

Blomgren, J.; Hildebrand, A.; Nilsson, L.; Mermod, P.; Olsson, N.; Pomp, S.; Oesterlund, M.

2004-08-01

The project NATT, Neutron data for Accelerator-driven Transmutation Technology, is performed within the nuclear reactions group of the Dept. of Neutron Research, Uppsala univ. The activities of the group are directed towards experimental studies of nuclear reaction probabilities of importance for various applications, like transmutation of nuclear waste, biomedical effects and electronics reliability. The experimental work is primarily undertaken at the The Svedberg Laboratory (TSL) in Uppsala, where the group has previously developed two world-unique instruments, MEDLEY and SCANDAL. Highlights from the past year: Analysis and documentation has been finalized of previously performed measurements of elastic neutron scattering from hydrogen at 96 MeV. The results corroborate the normalization of previously obtained data at TSL, which have been under debate. This is of importance since this reaction serves as reference for many other measurements. Compelling evidence of the existence of three-body forces in nuclei has been obtained. Within the project, one PhD exam and one licentiate exam has been awarded. One PhD exam and one licentiate exam has been awarded for work closely related to the project. A new neutron beam facility with significantly improved performance has been built and commissioned at TSL

Neutron data for accelerator-driven transmutation technologies. Annual Report 2003/2004

Energy Technology Data Exchange (ETDEWEB)

Blomgren, J.; Hildebrand, A.; Nilsson, L.; Mermod, P.; Olsson, N.; Pomp, S.; Oesterlund, M. [Uppsala Univ. (Sweden). Dept. for Neutron Research

2004-08-01

The project NATT, Neutron data for Accelerator-driven Transmutation Technology, is performed within the nuclear reactions group of the Dept. of Neutron Research, Uppsala univ. The activities of the group are directed towards experimental studies of nuclear reaction probabilities of importance for various applications, like transmutation of nuclear waste, biomedical effects and electronics reliability. The experimental work is primarily undertaken at the The Svedberg Laboratory (TSL) in Uppsala, where the group has previously developed two world-unique instruments, MEDLEY and SCANDAL. Highlights from the past year: Analysis and documentation has been finalized of previously performed measurements of elastic neutron scattering from hydrogen at 96 MeV. The results corroborate the normalization of previously obtained data at TSL, which have been under debate. This is of importance since this reaction serves as reference for many other measurements. Compelling evidence of the existence of three-body forces in nuclei has been obtained. Within the project, one PhD exam and one licentiate exam has been awarded. One PhD exam and one licentiate exam has been awarded for work closely related to the project. A new neutron beam facility with significantly improved performance has been built and commissioned at TSL.

Transmutation and neutron flux studies with fission chambers in the MEGAPIE target

International Nuclear Information System (INIS)

Chabod, S.; Foucher, Y.; Letourneau, A.; Marie, F.; Toussaint, J.C.; Blandin, Ch.; Chartier, F.; Fioni, G.

2005-01-01

Eight fission micro chambers will be inserted inside the central rod of the 1 MW liquid Pb-Bi MEGAPIE target in order to study the transmutation of two major actinides and to measure the neutron flux at a level of 5%. These chambers were developed for high neutron fluxes and tested at Laue Langevin Institute. (authors)

Neutron data experiments for transmutation. Annual Report 2006/2007

International Nuclear Information System (INIS)

Blomgren, J.; Andersson, P.; Bevilacqua, R.; Nilsson, L.; Pomp, S.; Simutkin, V.; Oehrn, A.; Oesterlund, M.

2007-10-01

The project NEXT, Neutron data Experiments for Transmutation, is performed within the nuclear reactions group of the Department of Neutron Research, Uppsala University. The activities of the group are directed towards experimental studies of nuclear reaction probabilities of importance for various applications, like transmutation of nuclear waste, biomedical effects and electronics reliability. The experimental work is primarily undertaken at the The Svedberg Laboratory (TSL) in Uppsala, where the group is operating two world-unique instruments, MEDLEY and SCANDAL. Highlights from the past year: The TSL neutron beam facility and the MEDLEY detector system have been upgraded. Funding for a major upgrade of the SCANDAL facility has been approved, and practical work has been initiated. Three new PhD students have been accepted. The Uppsala group contributed twelve accepted publications at the International Conference on Nuclear Data for Science and Technology, Nice, France, April 22-27, 2007. The EU project CANDIDE (Coordination Action on Nuclear Data for Industrial Development in Europe), coordinated by Jan Blomgren, started January 1, 2007. The EU project EFNUDAT (European Facilities for Nuclear Data research), partly coordinated by Jan Blomgren, started November 1, 2006. Nuclear power education has reached all-time high at Uppsala University. A contract with KSU (Nuclear Training and Safety Centre) on financing the increased volume of teaching for industry needs has been signed

Neutron data experiments for transmutation. Annual Report 2006/2007

Energy Technology Data Exchange (ETDEWEB)

Blomgren, J.; Andersson, P.; Bevilacqua, R.; Nilsson, L.; Pomp, S.; Simutkin, V.; Oehrn, A.; Oesterlund, M. (Uppsala Univ. (SE). Dept. of Neutron Research)

2007-10-15

The project NEXT, Neutron data Experiments for Transmutation, is performed within the nuclear reactions group of the Department of Neutron Research, Uppsala University. The activities of the group are directed towards experimental studies of nuclear reaction probabilities of importance for various applications, like transmutation of nuclear waste, biomedical effects and electronics reliability. The experimental work is primarily undertaken at the The Svedberg Laboratory (TSL) in Uppsala, where the group is operating two world-unique instruments, MEDLEY and SCANDAL. Highlights from the past year: The TSL neutron beam facility and the MEDLEY detector system have been upgraded. Funding for a major upgrade of the SCANDAL facility has been approved, and practical work has been initiated. Three new PhD students have been accepted. The Uppsala group contributed twelve accepted publications at the International Conference on Nuclear Data for Science and Technology, Nice, France, April 22-27, 2007. The EU project CANDIDE (Coordination Action on Nuclear Data for Industrial Development in Europe), coordinated by Jan Blomgren, started January 1, 2007. The EU project EFNUDAT (European Facilities for Nuclear Data research), partly coordinated by Jan Blomgren, started November 1, 2006. Nuclear power education has reached all-time high at Uppsala University. A contract with KSU (Nuclear Training and Safety Centre) on financing the increased volume of teaching for industry needs has been signed

Development and application of new parameters for TRU transmutation effectiveness

International Nuclear Information System (INIS)

Han, Chi Young

2005-02-01

Four new parameters (incineration branching ratio, incineration rate, incineration time, and incineration buckling) have been developed to evaluate quantitatively the TRU transmutation effectiveness and applied to transmutation of uranium and TRU. From the incineration branching ratio, it is possible to analyze the main contributors to fission reaction for transmutation of a target nuclide. From the incineration rate, it is available to evaluate the transmutation effectiveness in the viewpoint of a relative incineration rate to incineration potential of a target nuclide and its family. This parameter is also used to calculate the incineration time and incineration buckling together with the incineration branching ratio. The incineration time makes it possible to discuss more practically the transmutation speed instead of the existing other parameters. The incineration buckling can be used to evaluate the time behavior of the incineration rate and also employed to support the results from the incineration time. Taking into account the transmutation effectiveness and potential of uranium and TRU derived by using the parameters and an existing neutron economy parameter, it was noted that the thermal neutron energy is very preferable from the transmutation effectiveness point of view, on the other hand the fast neutron energy is effective from the transmutation potential. Applying them to the typical critical and subcritical TRU burners, it is indicated that the critical reactor containing fertile uranium undergoes effectively the selective TRU transmutation on the present fast spectrum. It was also noted that the uranium-free subcritical reactor could be operated effectively on a little softer spectrum due to the larger neutron excess in the present spectrum. It is expected that the new parameters developed in this study and the results are directly applicable to practical transmutation reactor design, in particular accelerator-driven transmutation reactor

Neutron transmutation doping

Energy Technology Data Exchange (ETDEWEB)

Jun, Byung Jin

2001-09-01

HE OVERALL STATE OF THE ART RELATED WITH NEUTRON TRANSMUTATION DOPING(NCT) IS SURVEYED. ITEMS RELATED FOR THE REALIZATION OF NTD IN HANARO IS FOCUSED. IN ADDITION TO THE UNIFORM IRRADIATION AND ACHIEVING THE TARGET RESISTIVITY WHICH ARE THE MOST IMPORTANT TECHNICAL REQUIREMENTS FOR THE NTD, OTHER ITEMS SUCH AS THE FUNCTION AND ROLE OF NTD, MARKET TREND, QUALITY CONTROL ARE INCLUDED. MEANWHILE THE ONLY ADVANTAGE OF NTD IS ACHIEVING VERY HIGH UNIFORMITY OF DOPING, IT HAS SEVERAL DISADVANTAGES DUE TO THE USE OF NUCLEAR REACTOR. THEREFORE THE SEMICONDUCTOR INDUSTRY HAS CONTINUED DEVELOPMENT OF TECHNOLOGY TO REPLACE NTD, AND THE DEMAND OF NTD HAD BEEN DECREASED A LOT DURING 1990S. AS THE DEMAND FOR LARGE CRYSTAL INCREASES, HOWEVER, THE NTD DEMAND BEGAN TO INCREASE AGAIN FROM 2000. SINCE THE DEMAND FOR THE LARGER CRYSTAL WILL BE CONTINUED IN THE FUTURE, THE ROLE OF NTD WOULD BE NEEDED FOR THE LONGER TIME. IN ORDER TO MITIGATE THIS TREND OF DEMAND, THE REACTOR SHOULD BE CAPABLE OF ACCEPTING LARGE CRYSTAL AND THE EFFORT TO IMPROVE DOPING UNIFORMITY AND TO REDUCE THE COST SHOULD CONTINUED.

Nuclear transmutations

International Nuclear Information System (INIS)

Mikulaj, V.

1992-01-01

Two types of nuclear transmutations are outlined, namely the radioactive transmutations and nuclear reactions. The basic characteristics are given of radioactive transmutations (gamma transmutations and isomeric transitions, beta, alpha transmutations, spontaneous fission and spontaneous emission of nucleons), their kinetics and the influence of the physical and chemical state of the radionuclide on the transmutation rate. The basic characteristics are described of nuclear reactions (reactions of neutrons including fission, reactions induced by charged particles and photons), their kinetics, effective cross sections and their mechanism. Chemical reactions caused by nuclear transmutations are discussed (recoil energy, properties of hot atoms, Szilard-Chalmers effect). A brief information is given on the behavior of radionuclides in trace concentrations. (Z.S.) 2 tabs., 19 figs., 12 refs

Simulating irradiation hardening in tungsten under fast neutron irradiation including Re production by transmutation

Science.gov (United States)

Huang, Chen-Hsi; Gilbert, Mark R.; Marian, Jaime

2018-02-01

Simulations of neutron damage under fusion energy conditions must capture the effects of transmutation, both in terms of accurate chemical inventory buildup as well as the physics of the interactions between transmutation elements and irradiation defect clusters. In this work, we integrate neutronics, primary damage calculations, molecular dynamics results, Re transmutation calculations, and stochastic cluster dynamics simulations to study neutron damage in single-crystal tungsten to mimic divertor materials. To gauge the accuracy and validity of the simulations, we first study the material response under experimental conditions at the JOYO fast reactor in Japan and the High Flux Isotope Reactor at Oak Ridge National Laboratory, for which measurements of cluster densities and hardening levels up to 2 dpa exist. We then provide calculations under expected DEMO fusion conditions. Several key mechanisms involving Re atoms and defect clusters are found to govern the accumulation of irradiation damage in each case. We use established correlations to translate damage accumulation into hardening increases and compare our results to the experimental measurements. We find hardening increases in excess of 5000 MPa in all cases, which casts doubts about the integrity of W-based materials under long-term fusion exposure.

Neutron data for accelerator-driven transmutation technologies. Annual Report 2002/2003

International Nuclear Information System (INIS)

Blomgren, J.; Hildebrand, A.; Mermod, P.; Olsson, N.; Pomp, S.; Oesterlund, M.

2003-08-01

The project NATT, Neutron data for Accelerator-driven Transmutation Technology, is performed within the nuclear reactions group of the Department for neutron research, Uppsala university. The activities of the group is directed towards experimental studies of nuclear reaction probabilities of importance for various applications, like transmutation of nuclear waste, biomedical effects and electronics reliability. The experimental work is primarily undertaken at the The Svedberg Laboratory (TSL) in Uppsala, where the group has previously developed two world-unique instruments, MEDLEY and SCANDAL. Highlights from the past year: Analysis and documentation has been finalized of previously performed measurements of elastic neutron scattering from carbon and lead at 96 MeV. The precision in the results surpasses all previous data by at least an order of magnitude. These measurements represent the highest energy in neutron scattering where the ground state has been resolved. The results show that all previous theory work has underestimated the probability for neutron scattering at the present energy by 0-30 %. A new method for measurements of absolute probabilities for neutron-induced nuclear reactions with experimental techniques only has been developed. Previously, only two such methods have been known. One student has reached his PhD exam. Two PhD students have been accepted. TSL has decided to build a new neutron beam facility with significantly improved performance for these, and similar, activities. A new instrument for measurements of inelastic neutron scattering has been built, tested and found to meet the specifications. This work has been performed in collaboration with two French research groups from Caen and Nantes. The instrument is intended to be used for a series of experiments during the coming years. Previous work by the group on nuclear data for assessment of electronics reliability has lead to a new industry standard in the USA

Neutron data for accelerator-driven transmutation technologies. Annual Report 2002/2003

Energy Technology Data Exchange (ETDEWEB)

Blomgren, J.; Hildebrand, A.; Mermod, P.; Olsson, N.; Pomp, S.; Oesterlund, M. [Uppsala Univ. (Sweden). Dept. for Neutron Research

2003-08-01

The project NATT, Neutron data for Accelerator-driven Transmutation Technology, is performed within the nuclear reactions group of the Department for neutron research, Uppsala university. The activities of the group is directed towards experimental studies of nuclear reaction probabilities of importance for various applications, like transmutation of nuclear waste, biomedical effects and electronics reliability. The experimental work is primarily undertaken at the The Svedberg Laboratory (TSL) in Uppsala, where the group has previously developed two world-unique instruments, MEDLEY and SCANDAL. Highlights from the past year: Analysis and documentation has been finalized of previously performed measurements of elastic neutron scattering from carbon and lead at 96 MeV. The precision in the results surpasses all previous data by at least an order of magnitude. These measurements represent the highest energy in neutron scattering where the ground state has been resolved. The results show that all previous theory work has underestimated the probability for neutron scattering at the present energy by 0-30 %. A new method for measurements of absolute probabilities for neutron-induced nuclear reactions with experimental techniques only has been developed. Previously, only two such methods have been known. One student has reached his PhD exam. Two PhD students have been accepted. TSL has decided to build a new neutron beam facility with significantly improved performance for these, and similar, activities. A new instrument for measurements of inelastic neutron scattering has been built, tested and found to meet the specifications. This work has been performed in collaboration with two French research groups from Caen and Nantes. The instrument is intended to be used for a series of experiments during the coming years. Previous work by the group on nuclear data for assessment of electronics reliability has lead to a new industry standard in the USA.

Gamma ray beam transmutation

International Nuclear Information System (INIS)

Imasaki, K.; Li, D.; Miyamoto, S.; Amano, S.; Motizuki, T.

2007-01-01

We have proposed a new approach to nuclear transmutation by a gamma ray beam of Compton scattered laser photon. We obtained 20 MeV gamma ray in this way to obtain transmutation rates with the giant resonance of 1 97Au and 1 29Iodine. The rate of the transmutation agreed with the theoretical calculation. Experiments on energy spectrum of positron, electron and neutron from targets were performed for the energy balance and design of the system scheme. The reaction rate was about 1.5∼4% for appropriate photon energies and neutron production rate was up to 4% in the measurements. We had stored laser photon more than 5000 times in a small cavity which implied for a significant improvement of system efficiency. Using these technologies, we have designed an actual transmutation system for 1 29Iodine which has a 16 million year's activity. In my presentation, I will address the properties of this scheme, experiments results and transmutation system for iodine transmutation

Partitioning and transmutation (P and T) 1997. Status report

International Nuclear Information System (INIS)

Enarsson, Aasa; Landgren, A.; Liljenzin, J.O.; Skaalberg, M.; Spjuth, L.; Gudowski, W.; Wallenius, J.

1998-05-01

Research on and the evaluation of partitioning and transmutation are currently in progress in many industrial countries due to its potential as a long-term, sustainable energy source with low environmental impact and due to its ability to destroy many long-lived nuclides. The cost of the research and development work on partitioning and transmutation is considered to be so great that international co-operation is required. With respect to Sweden, we recommend a balanced research work on both partitioning and transmutation technology. Within the area of partitioning, it is above all a question of locating new reagents which can be used to simplify the necessary partitioning processes and minimize the losses. The requirements with respect to high selectivity and minor losses will be significantly higher in a recirculating system based on transmutation than in the reprocessing facilities of today where only uranium and plutonium are recovered. If the utilized reagents can be easily destroyed, by dry or wet incineration and conversion into non-complex gaseous chemical compounds, this will open up good opportunities for the recovery of the radionuclides. From a purely technical standpoint, it would seem that a combination of different types of reactor systems would give the best possible transmutation efficiency. While existing light water reactors can be utilized for increased plutonium incineration, there is currently consensus about the view that reactors with high-energy neutrons are necessary to achieve a sufficiently high transmutation efficiency for neptunium, americium, curium and certain fission products. By allowing an accelerator-based neutron source to drive a subcritical heavy metal-cooled reactor, the potential for transmutation of fission products is increased, at the same time that satisfactory safety margins are achieved for certain fuel types with a low share of delayed neutrons and a high heat conductivity. Regardless of what types of systems are

Partitioning and transmutation (P and T) 1997. Status report

Energy Technology Data Exchange (ETDEWEB)

Enarsson, Aasa; Landgren, A.; Liljenzin, J.O.; Skaalberg, M.; Spjuth, L. [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Nuclear Chemistry; Gudowski, W.; Wallenius, J. [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Nuclear and Reactor Physics

1998-05-01

Research on and the evaluation of partitioning and transmutation are currently in progress in many industrial countries due to its potential as a long-term, sustainable energy source with low environmental impact and due to its ability to destroy many long-lived nuclides. The cost of the research and development work on partitioning and transmutation is considered to be so great that international co-operation is required. With respect to Sweden, we recommend a balanced research work on both partitioning and transmutation technology. Within the area of partitioning, it is above all a question of locating new reagents which can be used to simplify the necessary partitioning processes and minimize the losses. The requirements with respect to high selectivity and minor losses will be significantly higher in a recirculating system based on transmutation than in the reprocessing facilities of today where only uranium and plutonium are recovered. If the utilized reagents can be easily destroyed, by dry or wet incineration and conversion into non-complex gaseous chemical compounds, this will open up good opportunities for the recovery of the radionuclides. From a purely technical standpoint, it would seem that a combination of different types of reactor systems would give the best possible transmutation efficiency. While existing light water reactors can be utilized for increased plutonium incineration, there is currently consensus about the view that reactors with high-energy neutrons are necessary to achieve a sufficiently high transmutation efficiency for neptunium, americium, curium and certain fission products. By allowing an accelerator-based neutron source to drive a subcritical heavy metal-cooled reactor, the potential for transmutation of fission products is increased, at the same time that satisfactory safety margins are achieved for certain fuel types with a low share of delayed neutrons and a high heat conductivity. Regardless of what types of systems are

Electrical property studies of neutron-transmutation-doped silicon

International Nuclear Information System (INIS)

Cleland, J.W.; Fleming, P.H.; Westbrook, R.D.; Wood, R.F.; Young, R.T.

1978-01-01

Results of studies of electrical properties of neutron-transmutation-doped (NTD) silicon are presented. Annealing requirements to remove lattice damage were obtained. The electrical role of clustered oxygen and defect-oxygen complex was investigated. An NTD epitaxial layer on a heavily doped n- or p- type substrate can be produced. There is no evident interaction between lithium introduced by diffusion and phosphorous 31 introduced by irradiation. There may be some type of pairing reaction between lithium 7 introduced by boron 10 fission and any remaining boron

Neutronic design and analysis on dual-cooled waste transmutation blanket for the fusion driven sub-critical system

International Nuclear Information System (INIS)

Zheng Shanliang; Wu Yican; Gao Chunjing; Xu Dezheng; Li Jingjing; Zhu Xiaoxiang

2004-01-01

Neutronics design and analysis of dual-cooled multi-functional waste transmutation blanket (DWTB) for the fusion driven sub-critical system (FDS) are performed to ensure the system be able to meet the requirements of fuel-sufficiency and more waste transmutation ratio with low initial loading fuel inventory, which is based on 1-D burn-up calculations with home-developed code Visual BUS and the multi-group (175 neutron groups-42 Gamma groups coupled) data library HENDL1.0/MG (Hybrid Evaluated Nuclear Data Library). (authors)

Calculation of displacement, gas, and transmutation production in stainless steel irradiated with spallation neutrons

International Nuclear Information System (INIS)

Wechsler, M.A.; Ramavarapu, R.; Daugherty, E.L.; Palmer, R.C.; Bullen, D.B.; Sommer, W.F.

1993-01-01

Calculations using the high-energy transport code LAHET have been made for the production of displacements, helium gas, and transmuted atoms for stainless steel (Fe-18 wt % Cr-10 wt % Ni) irradiated with spallation neutrons at energies of 100 to 1600 MeV. The damage energy cross section increased from about 250 to 350 b keV for increasing neutron energies from 100 to 1600 MeV with a spallation spectrum average of 281 barns-keV. For a displacement threshold energy of 33 eV, the corresponding spectrum-average displacement cross section is 3400 barns. The PKA spectrum was found to be fairly independent of the incident neutron energy, with an average damage energy of 0.25--0.30 MeV. The helium production cross section increased monotonically with increasing neutron energy, with a spectrum average of 0.32 barns. The maximum transmutation yield was observed near manganese (Z = 25), corresponding to a production cross section of about 0.2 barns. Relevance to fusion materials is discussed

Annealing behaviour of excess carriers in neutron-transmutation-doped silicon

International Nuclear Information System (INIS)

Maekawa, T.; Nogami, S.; Inoue, S.

1993-01-01

In neutron-transmutation-doped silicon wafers excess carriers are clearly generated over the transmuted phosphorus atoms. The generation occurs for annealing temperatures above 900 o C. The maximum percentage of excess carriers obtained is about 24.5% of the final carrier concentration. Due to the difference in energy of generation and removal, the excess carriers can be removed by annealing above 800 o C. The radiation damage responsible for generation of excess carriers is fairly thermostable in the range of annealing temperatures below 800 o C. From deep-level transient spectroscopy measurements, it is found that the radiation damage remains insensitive to changes in carrier concentration. The activation energies of excess carrier generation and removal are estimated from the analysis of the thermal and temporal behaviours of radiation damage in the annealing process. (Author)

Transmutation approximations for the application of hybrid Monte Carlo/deterministic neutron transport to shutdown dose rate analysis

International Nuclear Information System (INIS)

Biondo, Elliott D.; Wilson, Paul P. H.

2017-01-01

In fusion energy systems (FES) neutrons born from burning plasma activate system components. The photon dose rate after shutdown from resulting radionuclides must be quantified. This shutdown dose rate (SDR) is calculated by coupling neutron transport, activation analysis, and photon transport. The size, complexity, and attenuating configuration of FES motivate the use of hybrid Monte Carlo (MC)/deterministic neutron transport. The Multi-Step Consistent Adjoint Driven Importance Sampling (MS-CADIS) method can be used to optimize MC neutron transport for coupled multiphysics problems, including SDR analysis, using deterministic estimates of adjoint flux distributions. When used for SDR analysis, MS-CADIS requires the formulation of an adjoint neutron source that approximates the transmutation process. In this work, transmutation approximations are used to derive a solution for this adjoint neutron source. It is shown that these approximations are reasonably met for typical FES neutron spectra and materials over a range of irradiation scenarios. When these approximations are met, the Groupwise Transmutation (GT)-CADIS method, proposed here, can be used effectively. GT-CADIS is an implementation of the MS-CADIS method for SDR analysis that uses a series of single-energy-group irradiations to calculate the adjoint neutron source. For a simple SDR problem, GT-CADIS provides speedups of 200 100 relative to global variance reduction with the Forward-Weighted (FW)-CADIS method and 9 _± 5 • _1_0_"_4 relative to analog. As a result, this work shows that GT-CADIS is broadly applicable to FES problems and will significantly reduce the computational resources necessary for SDR analysis.

Transmutation studies using SSNTD and radiochemistry and the associated production of secondary neutrons

CERN Document Server

Brandt, R; Wan, J S; Schmidt, T; Langrock, E J; Vater, P; Adam, J; Bamblevski, V P; Bradnova, V; Gelovani, L K; Kalinnikov, V K; Krivopustov, M I; Kulakov, B A; Sosnin, A N; Perelygin, V P; Pronskikh, V S; Stegailov, V I; Tsoupko-Sitnikov, V M; Modolo, G; Odoj, R; Philippen, P W; Adloff, J C; Pape, F; Debeauvais, M; Zamani-Valassiadou, M; Hashemi-Nezhad, S R; Dwivedi, K K; Guo Shi Lun; Li, L; Wang, Y L; Wilson, B

1999-01-01

Experiments using 1.5 GeV, 3.7 GeV and 7.4 GeV protons from the Synchrophasotron, LHE, JINR, Dubna, Russia, on extended Pb- and U- targets were carried out using SSNTD and radiochemical sensors for the study of secondary neutron $9 fluences. We also carried out first transmutation studies on the long-lived radwaste nuclei /sup 129/I and /sup 237/Np. In addition, we carried out computer code simulation studies on these systems using LAHET and DCM/CEM codes. We $9 have difficulties to understand rather large transmutation rates observed experimentally when they are compared with computer simulations. There seems to be a rather fundamental problem understanding the large transmutation rates as $9 observed experimentally in Dubna and CERN, as compared to those theoretical computer simulations mentioned above. (10 refs).

Detailed studies of Minor Actinide transmutation-incineration in high-intensity neutron fluxes

International Nuclear Information System (INIS)

Bringer, O.; Al Mahamid, I.; Blandin, C.; Chabod, S.; Chartier, F.; Dupont, E.; Fioni, G.; Isnard, H.; Letourneau, A.; Marie, F.; Mutti, P.; Oriol, L.; Panebianco, S.; Veyssiere, C.

2006-01-01

The Mini-INCA project is dedicated to the measurement of incineration-transmutation chains and potentials of minor actinides in high-intensity thermal neutron fluxes. In this context, new types of detectors and methods of analysis have been developed. The 241 Am and 232 Th transmutation-incineration chains have been studied and several capture and fission cross sections measured very precisely, showing some discrepancies with existing data or evaluated data. An impact study was made on different based-like GEN-IV reactors. It underlines the necessity to proceed to precise measurements for a large number of minor-actinides that contribute to these future incineration scenarios. (authors)

Detailed studies of Minor Actinide transmutation-incineration in high-intensity neutron fluxes

Energy Technology Data Exchange (ETDEWEB)

Bringer, O. [CEA/Saclay/DSM/DAPNIA, Gif-sur-Yvette (France); Al Mahamid, I. [Lawrence Berkeley National Laboratory, E.H. and S. Div., CA (United States); Blandin, C. [CEA/Cadarache/DEN/DER/SPEX, Saint-Paul-lez-Durances (France); Chabod, S. [CEA/Saclay/DSM/DAPNIA, Gif-sur-Yvette (France); Chartier, F. [CEA/Cadarache/DEN/DPC/SECR, Gif-sur-Yvette (France); Dupont, E.; Fioni, G. [CEA/Saclay/DSM/DAPNIA, Gif-sur-Yvette (France); Isnard, H. [CEA/Cadarache/DEN/DPC/SECR, Gif-sur-Yvette (France); Letourneau, A.; Marie, F. [CEA/Saclay/DSM/DAPNIA, Gif-sur-Yvette (France); Mutti, P. [Institut Laue-Langevin, Grenoble (France); Oriol, L. [CEA/Cadarache/DEN/DER/SPEX, Saint-Paul-lez-Durances (France); Panebianco, S.; Veyssiere, C. [CEA/Saclay/DSM/DAPNIA, Gif-sur-Yvette (France)

2006-07-01

The Mini-INCA project is dedicated to the measurement of incineration-transmutation chains and potentials of minor actinides in high-intensity thermal neutron fluxes. In this context, new types of detectors and methods of analysis have been developed. The {sup 241}Am and {sup 232}Th transmutation-incineration chains have been studied and several capture and fission cross sections measured very precisely, showing some discrepancies with existing data or evaluated data. An impact study was made on different based-like GEN-IV reactors. It underlines the necessity to proceed to precise measurements for a large number of minor-actinides that contribute to these future incineration scenarios. (authors)

Determination of procedures for transmutation of fission product wastes by fusion neutrons. Volume 2. Final report

International Nuclear Information System (INIS)

Lang, G.P.

1980-12-01

This study is concerned with the engineering aspects of the transmutation of fission products utilizing neutrons generated in fusion reactors. It is assumed that fusion reactors, although not yet developed, will be available around the turn of the century. Therefore, early studies of this type are appropriate as a guide to the large amount of further investigations that will be needed to fully evaluate this concept. Not all of the radioactive products from light water reactors can be economically transmuted, but it appears that the most hazardous can. This requires that fission-product wastes must first be separated into a number of fractions, and in some instances this must be accomplished with extremely high separation factors. A review of current commercial separation processes and of promising methods that are now in the laboratory stage indicate that the necessary processes can most likely be developed but will require an active and sustained development program. Current fusion reactor concepts were examined as to their suitability for transmuting the separated fission wastes. It was concluded that the long-lived fission products were most amenable to transmutation. The medium-lived fission products, Cs-137 and Sr-90, require higher neutron fluxes than are available in the most developed fusion reactor concepts. Concepts which are less developed may eventually be adaptable as transmuters of these fission products

Analysis and optimization of minor actinides transmutation blankets with regards to neutron and gamma sources

International Nuclear Information System (INIS)

Kooyman, T.; Buiron, L.; Rimpault, G.

2017-01-01

Heterogeneous loading of minor actinides in radial blankets is a potential solution to implement minor actinides transmutation in fast reactors. However, to compensate for the lower flux level experienced by the blankets, the fraction of minor actinides to be loaded in the blankets must be increased to maintain acceptable performances. This severely increases the decay heat and neutron source of the blanket assemblies, both before and after irradiation, by more than an order of magnitude in the case of neutron source for instance. We propose here to implement an optimization methodology of the blankets design with regards to various parameters such as the local spectrum or the mass to be loaded, with the objective of minimizing the final neutron source of the spent assembly while maximizing the transmutation performances of the blankets. In a first stage, an analysis of the various contributors to long- and short-term neutron and gamma source is carried out whereas in a second stage, relevant estimators are designed for use in the effective optimization process, which is done in the last step. A comparison with core calculations is finally done for completeness and validation purposes. It is found that the use of a moderated spectrum in the blankets can be beneficial in terms of final neutron and gamma source without impacting minor actinides transmutation performances compared to more energetic spectrum that could be achieved using metallic fuel for instance. It is also confirmed that, if possible, the use of hydrides as moderating material in the blankets is a promising option to limit the total minor actinides inventory in the fuel cycle. If not, it appears that focus should be put upon an increased residence time for the blankets rather than an increase in the acceptable neutron source for handling and reprocessing. (authors)

Analysis and optimization of minor actinides transmutation blankets with regards to neutron and gamma sources

Directory of Open Access Journals (Sweden)

Kooyman Timothée

2017-01-01

Full Text Available Heterogeneous loading of minor actinides in radial blankets is a potential solution to implement minor actinides transmutation in fast reactors. However, to compensate for the lower flux level experienced by the blankets, the fraction of minor actinides to be loaded in the blankets must be increased to maintain acceptable performances. This severely increases the decay heat and neutron source of the blanket assemblies, both before and after irradiation, by more than an order of magnitude in the case of neutron source for instance. We propose here to implement an optimization methodology of the blankets design with regards to various parameters such as the local spectrum or the mass to be loaded, with the objective of minimizing the final neutron source of the spent assembly while maximizing the transmutation performances of the blankets. In a first stage, an analysis of the various contributors to long- and short-term neutron and gamma source is carried out whereas in a second stage, relevant estimators are designed for use in the effective optimization process, which is done in the last step. A comparison with core calculations is finally done for completeness and validation purposes. It is found that the use of a moderated spectrum in the blankets can be beneficial in terms of final neutron and gamma source without impacting minor actinides transmutation performances compared to more energetic spectrum that could be achieved using metallic fuel for instance. It is also confirmed that, if possible, the use of hydrides as moderating material in the blankets is a promising option to limit the total minor actinides inventory in the fuel cycle. If not, it appears that focus should be put upon an increased residence time for the blankets rather than an increase in the acceptable neutron source for handling and reprocessing.

Analysis and optimization of minor actinides transmutation blankets with regards to neutron and gamma sources

Science.gov (United States)

Kooymana, Timothée; Buiron, Laurent; Rimpault, Gérald

2017-09-01

Heterogeneous loading of minor actinides in radial blankets is a potential solution to implement minor actinides transmutation in fast reactors. However, to compensate for the lower flux level experienced by the blankets, the fraction of minor actinides to be loaded in the blankets must be increased to maintain acceptable performances. This severely increases the decay heat and neutron source of the blanket assemblies, both before and after irradiation, by more than an order of magnitude in the case of neutron source for instance. We propose here to implement an optimization methodology of the blankets design with regards to various parameters such as the local spectrum or the mass to be loaded, with the objective of minimizing the final neutron source of the spent assembly while maximizing the transmutation performances of the blankets. In a first stage, an analysis of the various contributors to long and short term neutron and gamma source is carried out while in a second stage, relevant estimators are designed for use in the effective optimization process, which is done in the last step. A comparison with core calculations is finally done for completeness and validation purposes. It is found that the use of a moderated spectrum in the blankets can be beneficial in terms of final neutron and gamma source without impacting minor actinides transmutation performances compared to more energetic spectrum that could be achieved using metallic fuel for instance. It is also confirmed that, if possible, the use of hydrides as moderating material in the blankets is a promising option to limit the total minor actinides inventory in the fuel cycle. If not, it appears that focus should be put upon an increased residence time for the blankets rather than an increase in the acceptable neutron source for handling and reprocessing.

Transmutation blanket design for a Tokamak system

International Nuclear Information System (INIS)

Velasquez, Carlos E.; Barros, Graiciany de P.; Pereira, Claubia; Veloso, Maria A. Fortini; Costa, Antonella L.

2011-01-01

Sub-critical advanced reactor with a D-T fusion neutron source based on Tokamak technology is an innovative type of nuclear system. Due to the high quantity of neutrons produced by fusion reactions, it could be well spent in the transmutation process of the transuranic elements. Nevertheless, to achieve a successful transmutation, it is necessary to know the neutron fluence along the radial axis and its characteristics. In this work, it evaluated the neutron flux and interaction frequency along the radial axis changing the material of the first wall. W-alloy, beryllium and the combination of both were studied and regions more suitable to transmutation were determined. The results demonstrated that the better zone to place a transmutation blanket is limited by the heat sink and the shield block. Material arrangements W-alloy/W-alloy and W-alloy/Beryllium would be able to hold the requirements of high fluence and hardening spectrum needed to transuranic transmutation. The system was simulated using the MCNP5 code, the ITER Final Design Report, 2001, and the FENDL/MC-2.1 nuclear data library. (author)

Minor actinide transmutation in accelerator driven systems

Energy Technology Data Exchange (ETDEWEB)

Friess, Friederike [IANUS, TU Darmstadt (Germany)

2015-07-01

Transmutation of radioactive waste, the legacy of nuclear energy use, gains rising interest. This includes the development of facilities able to transmute minor actinides (MA) into stable or short-lived isotopes before final disposal. The most common proposal is to use a double-strata approach with accelerator-driven-systems (ADS) for the efficient transmutation of MA and power reactors to dispose plutonium. An ADS consists of a sub-critical core that reaches criticality with neutrons supplied by a spallation target. An MCNP model of the ADS system Multi Purpose Research Reactor for Hightech Applications will be presented. Depletion calculations have been performed for both standard MOX fuel and transmutation fuel with an increased content of minor actinides. The resulting transmutation rates for MAs are compared to published values. Special attention is given to selected fission products such as Tc-99 and I-129, which impact the radiation from the spent fuel significantly.

Monte Carlo analysis of the long-lived fission product neutron capture rates at the Transmutation by Adiabatic Resonance Crossing (TARC) experiment

International Nuclear Information System (INIS)

Abánades, A.; Álvarez-Velarde, F.; González-Romero, E.M.; Ismailov, K.; Lafuente, A.; Nishihara, K.; Saito, M.; Stanculescu, A.; Sugawara, T.

2013-01-01

Highlights: ► TARC experiment benchmark capture rates results. ► Utilization of updated databases, included ADSLib. ► Self-shielding effect in reactor design for transmutation. ► Effect of Lead nuclear data. - Abstract: The design of Accelerator Driven Systems (ADS) requires the development of simulation tools that are able to describe in a realistic way their nuclear performance and transmutation rate capability. In this publication, we present an evaluation of state of the art Monte Carlo design tools to assess their performance concerning transmutation of long-lived fission products. This work, performed under the umbrella of the International Atomic Energy Agency, analyses two important aspects for transmutation systems: moderation on Lead and neutron captures of 99 Tc, 127 I and 129 I. The analysis of the results shows how shielding effects due to the resonances at epithermal energies of these nuclides affects strongly their transmutation rate. The results suggest that some research effort should be undertaken to improve the quality of Iodine nuclear data at epithermal and fast neutron energy to obtain a reliable transmutation estimation.

Dual neutral particle induced transmutation in CINDER2008

Energy Technology Data Exchange (ETDEWEB)

Martin, W.J., E-mail: wjmarti@sandia.gov [Sandia National Laboratories, Albuquerque, NM 87185 (United States); University of New Mexico, Albuquerque, NM 87131 (United States); Oliveira, C.R.E. de; Hecht, A.A. [University of New Mexico, Albuquerque, NM 87131 (United States)

2014-12-11

Although nuclear transmutation methods for fission have existed for decades, the focus has been on neutron-induced reactions. Recent novel concepts have sought to use both neutrons and photons for purposes such as active interrogation of cargo to detect the smuggling of highly enriched uranium, a concept that would require modeling the transmutation caused by both incident particles. As photonuclear transmutation has yet to be modeled alongside neutron-induced transmutation in a production code, new methods need to be developed. The CINDER2008 nuclear transmutation code from Los Alamos National Laboratory is extended from neutron applications to dual neutral particle applications, allowing both neutron- and photon-induced reactions for this modeling with a focus on fission. Following standard reaction modeling, the induced fission reaction is understood as a two-part reaction, with an entrance channel to the excited compound nucleus, and an exit channel from the excited compound nucleus to the fission fragmentation. Because photofission yield data—the exit channel from the compound nucleus—are sparse, neutron fission yield data are used in this work. With a different compound nucleus and excitation, the translation to the excited compound state is modified, as appropriate. A verification and validation of these methods and data has been performed. This has shown that the translation of neutron-induced fission product yield sets, and their use in photonuclear applications, is appropriate, and that the code has been extended correctly. - Highlights: • The CINDER2008 transmutation code was modified to include photon-induced transmutation tracking. • A photonuclear interaction library was created to allow CINDER2008 to track photonuclear interactions. • Photofission product yield data sets were created using fission physics similarities with neutron-induced fission.

High flux transmutation of fission products and actinides

International Nuclear Information System (INIS)

Gerasimov, A.; Kiselev, G.; Myrtsymova, L.

2001-01-01

Long-lived fission products and minor actinides accumulated in spent nuclear fuel of power reactors comprise the major part of high level radwaste. Their incineration is important from the point of view of radwaste management. Transmutation of these nuclides by means of neutron irradiation can be performed either in conventional nuclear reactors, or in specialized transmutation reactors, or in ADS facilities with subcritical reactor and neutron source with application of proton accelerator. Different types of transmutation nuclear facilities can be used in order to insure optimal incineration conditions for radwaste. The choice of facility type for optimal transmutation should be based on the fundamental data in the physics of nuclide transformations. Transmutation of minor actinides leads to the increase of radiotoxicity during irradiation. It takes significant time compared to the lifetime of reactor facility to achieve equilibrium without effective transmutation. High flux nuclear facilities allow to minimize these draw-backs of conventional facilities with both thermal and fast neutron spectrum. They provide fast approach to equilibrium and low level of equilibrium mass and radiotoxicity of transmuted actinides. High flux facilities are advantageous also for transmutation of long-lived fission products as they provide short incineration time

Neutron irradiation control in the neutron transmutation doping process in HANARO using SPND

Energy Technology Data Exchange (ETDEWEB)

Kang, Gi-Doo; Kim, Myong-Seop [Korea Atomic Energy Research Institute, Yuseong, Daejeon, 305-353, (Korea, Republic of)

2015-07-01

The neutron irradiation control method by using self-powered neutron detector (SPND) is developed for the neutron transmutation doping (NTD) application in HANARO. An SPND is installed at a fixed position of the upper part of the sleeve in HANARO NTD hole for real-time monitoring of the neutron irradiation. It is confirmed that the SPND is significantly affected by the in-core condition and surroundings of the facility. Furthermore, the SPND signal changes about 15% throughout a whole cycle according to the change of the control rod position. But, it is also confirmed that the variation of the neutron flux on the silicon ingots inside the irradiation can is not so big while moving of the control rod. Accordingly, the relationship between the ratio of the neutron flux to the SPND signal output and the control rod position is established. In this procedure, the neutron flux measurement by using zirconium foil is utilized. The real NTD irradiation experiments are performed using the established relationship. The irradiated neutron fluence can be controlled within ±1.3% of the target one. The mean value of the irradiation/target ratio of the fluence is 0.9992, and the standard deviation is 0.0071. Thus, it is confirmed that the extremely accurate irradiation would be accomplished. This procedure can be useful for the SPND application installed at the fixed position to the field requiring the extremely high accuracy. (authors)

Transmutation of All German Transuranium under Nuclear Phase Out Conditions - Is This Feasible from Neutronic Point of View?

Science.gov (United States)

Merk, Bruno; Litskevich, Dzianis

2015-01-01

The German government has decided for the nuclear phase out, but a decision on a strategy for the management of the highly radioactive waste is not defined yet. Partitioning and Transmutation (P&T) could be considered as a technological option for the management of highly radioactive waste, therefore a wide study has been conducted. In the study group objectives for P&T and the boundary conditions of the phase out have been discussed. The fulfillment of the given objectives is analyzed from neutronics point of view using simulations of a molten salt reactor with fast neutron spectrum. It is shown that the efficient transmutation of all existing transuranium isotopes would be possible from neutronic point of view in a time frame of about 60 years. For this task three reactors of a mostly new technology would have to be developed and a twofold life cycle consisting of a transmuter operation and a deep burn phase would be required. A basic insight for the optimization of the time duration of the deep burn phase is given. Further on, a detailed balance of different isotopic inventories is given to allow a deeper understanding of the processes during transmutation in the molten salt fast reactor. The effect of modeling and simulation is investigated based on three different modeling strategies and two different code versions.

Transmutation of All German Transuranium under Nuclear Phase Out Conditions - Is This Feasible from Neutronic Point of View?

Directory of Open Access Journals (Sweden)

Bruno Merk

Full Text Available The German government has decided for the nuclear phase out, but a decision on a strategy for the management of the highly radioactive waste is not defined yet. Partitioning and Transmutation (P&T could be considered as a technological option for the management of highly radioactive waste, therefore a wide study has been conducted. In the study group objectives for P&T and the boundary conditions of the phase out have been discussed. The fulfillment of the given objectives is analyzed from neutronics point of view using simulations of a molten salt reactor with fast neutron spectrum. It is shown that the efficient transmutation of all existing transuranium isotopes would be possible from neutronic point of view in a time frame of about 60 years. For this task three reactors of a mostly new technology would have to be developed and a twofold life cycle consisting of a transmuter operation and a deep burn phase would be required. A basic insight for the optimization of the time duration of the deep burn phase is given. Further on, a detailed balance of different isotopic inventories is given to allow a deeper understanding of the processes during transmutation in the molten salt fast reactor. The effect of modeling and simulation is investigated based on three different modeling strategies and two different code versions.

Study of a neutronic potential of a modular fast spectrum ADS for radiotoxic waste transmutation

International Nuclear Information System (INIS)

Slessarev, I.; Arkhipov, V.

1999-01-01

The IAEA has maintained an active interest in advanced nuclear technology related to Accelerator Driven Systems (ADS). The activities carried out by the IAEA within its Programme on Emerging Nuclear Energy Systems for Energy Generation and Transmutation include preparation of status reports on advanced technologies development, conduct of technical information exchange meetings and co-operative Co-ordinated Research Programmes (CRPs). Consultancy on Accelerator Driven Systems and Related Fuel Cycles held from 1-2 February 1996 in Cadarache, France reviewed the recent progress in studies on feasibility of Accelerator Driven Systems and participants recommended the IAEA to organize a CRP to investigate the accelerator driven systems potential. In 1996 the CRP: 'Use of Th-based Fuel Cycle in Accelerator Driven Systems (ADS) to Incinerate Pu and to Reduce Long-term Waste Toxicities' was established and the first Research Coordination Meeting was convened in March 1997 at the ENEA Research Center in Bologna, Italy. Results of the first stage 'Accelerator Driven Systems (ADS)-Neutronic Benchmark' were reported to the IAEA Technical Committee Meeting on Feasibility and Motivation for Hybrid Concepts for Nuclear Energy Generation and Transmutation in Madrid, Spain, in September 1997. Results obtained during the second stage of the CRP were presented and analysed at the RCM in December 1998 in Petten, Netherlands. The meeting was attended by 21 representatives and observers from IAEA, Belarus, Czech Republic, France, Germany, Italy, the Netherlands, the Russian Federation, Spain, Sweden and USA. This paper was prepared on recommendation of the participants of the meeting in Petten, Netherlands. Accelerator Driven System (ADS) neutronic potential, i.e. capability to burnout transuranic elements (TRU) or minor actinides (MA) and Long-Lived Fission Products (LLFP) with minimum ADS park as well as the rate of LLFP transmutation (mass/energy production) for nuclear waste

Safety characteristics of potential waste transmutation systems

International Nuclear Information System (INIS)

Van Tuyle, G.J.

1993-01-01

For nuclear waste transmutation to alter significantly the need for geologic disposal of spent fuel from US Light-water reactors (LWRs), about 1.4% of the spent fuel (by mass) must be separated and transmuted. This includes the plutonium, the minor actinides, and four fission products: iodine. technetium, cesium and strontium. Regarding the actinides, fissioning of the plutonium, neptunium, americium, and curium generates a great deal of heat, so much so that most of the plutonium should be used to produce power. However, these actinides have some undesirable neutronic characteristics, and their utilization in reactors or subcritical (proton-accelerator) targets requires either a fast neutronic spectrum or a very high thermal-neutron flux. Transmutation of the fission products is generally by neutron capture, although this is difficult in the case of cesium and strontium. In this paper, various proposed means of transmuting the actinides and fission products are discussed, with the main focus being on the safety characteristics of each approach

Neutron Transmutation Doping of Silicon at Research Reactors

International Nuclear Information System (INIS)

2012-05-01

This publication details the processes and history of neutron transmutation doping of silicon, particularly its commercial pathway, followed by the requirements for a technologically modern and economically viable production scheme and the current trends in the global market for semiconductor products. It should serve as guidelines on the technical requirements, involved processes and required quality standards for the transmission of sound practices and advice for research reactor managers and operators planning commercial scale production of silicon. Furthermore, a detailed and specific database of most of the world's research reactor facilities in this domain is included, featuring their characteristics for irradiation capabilities, associated production capacities and processing.

Monte Carlo analysis of the long-lived fission product neutron capture rates at the Transmutation by Adiabatic Resonance Crossing (TARC) experiment

Energy Technology Data Exchange (ETDEWEB)

Abanades, A., E-mail: abanades@etsii.upm.es [Grupo de Modelizacion de Sistemas Termoenergeticos, ETSII, Universidad Politecnica de Madrid, c/Ramiro de Maeztu, 7, 28040 Madrid (Spain); Alvarez-Velarde, F.; Gonzalez-Romero, E.M. [Centro de Investigaciones Medioambientales y Tecnologicas (CIEMAT), Avda. Complutense, 40, Ed. 17, 28040 Madrid (Spain); Ismailov, K. [Tokyo Institute of Technology, 2-12-1, O-okayama, Meguro-ku, Tokyo 152-8550 (Japan); Lafuente, A. [Grupo de Modelizacion de Sistemas Termoenergeticos, ETSII, Universidad Politecnica de Madrid, c/Ramiro de Maeztu, 7, 28040 Madrid (Spain); Nishihara, K. [Transmutation Section, J-PARC Center, JAEA, Tokai-mura, Ibaraki-ken 319-1195 (Japan); Saito, M. [Tokyo Institute of Technology, 2-12-1, O-okayama, Meguro-ku, Tokyo 152-8550 (Japan); Stanculescu, A. [International Atomic Energy Agency (IAEA), Vienna (Austria); Sugawara, T. [Transmutation Section, J-PARC Center, JAEA, Tokai-mura, Ibaraki-ken 319-1195 (Japan)

2013-01-15

Highlights: Black-Right-Pointing-Pointer TARC experiment benchmark capture rates results. Black-Right-Pointing-Pointer Utilization of updated databases, included ADSLib. Black-Right-Pointing-Pointer Self-shielding effect in reactor design for transmutation. Black-Right-Pointing-Pointer Effect of Lead nuclear data. - Abstract: The design of Accelerator Driven Systems (ADS) requires the development of simulation tools that are able to describe in a realistic way their nuclear performance and transmutation rate capability. In this publication, we present an evaluation of state of the art Monte Carlo design tools to assess their performance concerning transmutation of long-lived fission products. This work, performed under the umbrella of the International Atomic Energy Agency, analyses two important aspects for transmutation systems: moderation on Lead and neutron captures of {sup 99}Tc, {sup 127}I and {sup 129}I. The analysis of the results shows how shielding effects due to the resonances at epithermal energies of these nuclides affects strongly their transmutation rate. The results suggest that some research effort should be undertaken to improve the quality of Iodine nuclear data at epithermal and fast neutron energy to obtain a reliable transmutation estimation.

Measurements of neutron yields and radioactive isotope transmutation in collisions of relativistic ions with heavy nuclei

International Nuclear Information System (INIS)

Brandt, R.

1999-01-01

The paper is based on the report presented at the 85th Session of the JINR Scientific Council. Some aspects of experimental studies of the problem of reprocessing radioactive wastes by means of transmutation in the fields of neutrons generated by relativistic particle beams are discussed. Research results on measurement of neutron yields in heavy targets irradiated with protons at energies up to 3.7 GeV as well as transmutation cross sections of some fission products (I-129) and actinides (Np-237) using radiochemical methods, activation detectors, solid state nuclear track detectors and other methods are presented. Experiments have been performed at the accelerator complex of the Laboratory of High Energies, JINR. Analogous results obtained by other research groups are also discussed

Neutron data experiments for transmutation. Annual Report 2007/2008

Energy Technology Data Exchange (ETDEWEB)

Blomgren, J.; al-Adili, A.; Andersson, P.; Bevilacqua, R.; Nilsson, L.; Pomp, S.; Simutkin, V.; Oehrn, A.; Oesterlund, M. (Uppsala Univ. (Sweden). Div. of Applied Nuclear Physics)

2008-08-15

The project NEXT, Neutron data Experiments for Transmutation, is performed within the nuclear reactions group of the Dept. of Physics and Astronomy. The activities of the group are directed towards experimental studies of nuclear reaction probabilities of importance for various applications, like transmutation of nuclear waste, biomedical effects and electronics reliability. The experimental work is primarily undertaken at the The Svedberg Laboratory (TSL) in Uppsala, where the group is operating two world-unique instruments, MEDLEY and SCANDAL. Highlights from the past year: - The SCANDAL facility has been upgraded. - One PhD student has successfully defended her thesis. - Two PhD students have been accepted. - Vasily Simutkin has been selected as one of the top 12 PhD students within the European Nuclear Education Network. He has accordingly been invited to present his work at the ENEN PhD event held in connection with the PHYSOR conference in Interlaken, Switzerland, September 2008. - A research collaboration with the dedicated EU laboratory for nuclear data research has been established. - A well-attended workshop on nuclear data for ADS and Gen-IV has been organized as part of the EU project CANDIDE (Coordination Action on Nuclear Data for Industrial Development in Europe), coordinated by Jan Blomgren. - Several experiments have been performed at TSL, with beamtime funded through the EU project EFNUDAT (European Facilities for Nuclear Data research), partly coordinated by Jan Blomgren. - Nuclear power education has reached all-time high at Uppsala University. In particular, industry education has increased significantly. - IAEA has visited Uppsala University to investigate the industry-related nuclear power education, as part of a safety culture review of the Forsmark nuclear power plant

Neutron data experiments for transmutation. Annual Report 2007/2008

International Nuclear Information System (INIS)

Blomgren, J.; Al-Adili, A.; Andersson, P.; Bevilacqua, R.; Nilsson, L.; Pomp, S.; Simutkin, V.; Oehrn, A.; Oesterlund, M.

2008-08-01

The project NEXT, Neutron data Experiments for Transmutation, is performed within the nuclear reactions group of the Dept. of Physics and Astronomy. The activities of the group are directed towards experimental studies of nuclear reaction probabilities of importance for various applications, like transmutation of nuclear waste, biomedical effects and electronics reliability. The experimental work is primarily undertaken at the The Svedberg Laboratory (TSL) in Uppsala, where the group is operating two world-unique instruments, MEDLEY and SCANDAL. Highlights from the past year: - The SCANDAL facility has been upgraded. - One PhD student has successfully defended her thesis. - Two PhD students have been accepted. - Vasily Simutkin has been selected as one of the top 12 PhD students within the European Nuclear Education Network. He has accordingly been invited to present his work at the ENEN PhD event held in connection with the PHYSOR conference in Interlaken, Switzerland, September 2008. - A research collaboration with the dedicated EU laboratory for nuclear data research has been established. - A well-attended workshop on nuclear data for ADS and Gen-IV has been organized as part of the EU project CANDIDE (Coordination Action on Nuclear Data for Industrial Development in Europe), coordinated by Jan Blomgren. - Several experiments have been performed at TSL, with beamtime funded through the EU project EFNUDAT (European Facilities for Nuclear Data research), partly coordinated by Jan Blomgren. - Nuclear power education has reached all-time high at Uppsala University. In particular, industry education has increased significantly. - IAEA has visited Uppsala University to investigate the industry-related nuclear power education, as part of a safety culture review of the Forsmark nuclear power plant

Study of spallation neutrons for the transmutation of long-lived nuclear waste

International Nuclear Information System (INIS)

Brochard, F.; Boyard, J.L.; Duchazeaubeneix, J.C.; Durand, J.M.; Faivre, J.C.; Leray, S.; Milleret, G.; Plouin, F.; Whittal, D.M.; Beau, M.; Crespin, S.; Frehaut, J.; Lochard, J.P.; Martinez, E.; Patin, Y.; Petitbon, E.; Sigaud, J.; Legrain, R.; Lepretre, A.; Terrien, Y.; Bacha, F.; Maillard, J.; Silva, J.

1994-01-01

With the renewed interest in accelerator-driven systems to transmute long-lived nuclear waste or to produce energy, new requirements for intermediate-energy nuclear data are now emerging. In all these systems, neutrons are produced by spallation reactions induced by around 1 GeV protons on a heavy target. These neutrons then drive a sub-critical blanket in which wastes are burned or energy is produced. A good knowledge of the spallation process (energy and angular distribution of the neutrons) is necessary to design and optimize the target-blanket system: for instance, to determine the best choices of beam energy, of composition and geometry of the target, in order to have the maximum neutron yield at the lowest cost, or to minimize the back-scattering of neutrons to the accelerator. A programme aimed at measuring the double differential cross-sections for the production of spallation neutrons induced by protons and deuterons GeV beams on different targets, is beginning at SATURNE. (authors). 3 refs., 3 figs

Transmutation of All German Transuranium under Nuclear Phase Out Conditions – Is This Feasible from Neutronic Point of View?

Science.gov (United States)

Merk, Bruno; Litskevich, Dzianis

2015-01-01

The German government has decided for the nuclear phase out, but a decision on a strategy for the management of the highly radioactive waste is not defined yet. Partitioning and Transmutation (P&T) could be considered as a technological option for the management of highly radioactive waste, therefore a wide study has been conducted. In the study group objectives for P&T and the boundary conditions of the phase out have been discussed. The fulfillment of the given objectives is analyzed from neutronics point of view using simulations of a molten salt reactor with fast neutron spectrum. It is shown that the efficient transmutation of all existing transuranium isotopes would be possible from neutronic point of view in a time frame of about 60 years. For this task three reactors of a mostly new technology would have to be developed and a twofold life cycle consisting of a transmuter operation and a deep burn phase would be required. A basic insight for the optimization of the time duration of the deep burn phase is given. Further on, a detailed balance of different isotopic inventories is given to allow a deeper understanding of the processes during transmutation in the molten salt fast reactor. The effect of modeling and simulation is investigated based on three different modeling strategies and two different code versions. PMID:26717509

Transmutation of fission products with the use of an accelarator

International Nuclear Information System (INIS)

Kase, T.; Harada, H.; Takahashi, T.

1995-01-01

The three transmutation methods with the use of an accelerator, the proton method, the spallation neutron method and the μCF method, are employed for the transmutation of long-lived nuclides in high level radioactive wastes. The transmutation energies and the effective half-lives of 99 Tc and 137 Cs for these transmutation methods are calculated by the Monte Carlo simulation codes for particle transport. The transmutation energies of the proton method are larger than those of the spallation neutron method and the μCF method under the condition of the same effective half life. The proton method is difficult to meet energy balance criterion. On the other hand, the spallation neutron method and the μCF method have possibility to meet the energy balance criterion. (author)

A neutron amplifier: prospects for reactor-based waste transmutation

International Nuclear Information System (INIS)

Blanovsky, A.

2004-01-01

A design concept and characteristics for an epithermal breeder controlled by variable feedback and external neutron source intensity are presented. By replacing the control rods with neutron sources, we could maintain good power distribution and perform radioactive waste burning in high flux subcritical reactors (HFSR) that have primary system size, power density and cost comparable to a pressurized water reactor (PWR). Another approach for actinide transmutation is a molten salt subcritical reactor proposed by Russian scientists. To increase neutron source intensity the HFSR is divided into two zones: a booster and a blanket with solid and liquid fuels. A neutron gate (absorber and moderator) imposed between two zones permits fast neutrons from the booster to flow to the blanket. Neutrons moving in the reverse direction are moderated and absorbed in the absorber zone. In the HFSR, neptunium-plutonium fuel is circulated in the booster and blanket, and americium-curium in the absorber zone and outer reflector. Use of a liquid actinide fuel permits transport of the delayed-neutron emitters from the blanket to the booster, where they can provide additional neutrons (source-dominated mode) or all the necessary excitation without an external neutron source (self-amplifying mode). With a blanket neutron multiplication gain of 20 and a booster gain of 50, an external neutron source rate of at least 10 15 n/s (0.7 MW D-T or 2.5 MW electron beam power) is needed to control the HFSR that produces 300 MWt. Most of the power could be generated in the blanket that burns about 100 kg of actinides a year. The analysis takes into consideration a wide range of HFSR design aspects including the wave model of observed relativistic phenomena, plant seismic diagnostics, fission electric cells (FEC) with a multistage collector (anode) and layered cathode. (author)

J-PARC Transmutation Experimental Facility Programme

International Nuclear Information System (INIS)

Sasa, T.; Takei, H.; Saito, S.; Obayashi, H.; Nishihara, K.; Sugawara, T.; Iwamoto, H.; Yamaguchi, K.; Tsujimoto, K.; Oigawa, H.

2015-01-01

Since the Fukushima accident, nuclear transmutation is considered as an option for waste management. Japan Atomic Energy Agency proposes the transmutation of minor actinides (MA) in accelerator-driven system (ADS) using lead-bismuth eutectic alloy (LBE) as a spallation target and a coolant of subcritical core. To obtain the data required for ADS design, we plan the building of a transmutation experimental facility (TEF) is planned within the J-PARC project. TEF consists of an ADS target test facility (TEF-T), which will be installed 400 MeV-250 kW LBE spallation target for material irradiations, and a transmutation physics experimental facility (TEF-P), which set up a fast critical/subcritical assembly driven by low power proton beam with MA fuel to study ADS neutronics. At TEF-T, various research plans to use emitted neutrons from LBE target are discussed. The paper summarises a road-map to establish the ADS transmuter and latest design activities for TEF construction. (authors)

Transmutation doping of silicon solar cells

Science.gov (United States)

Wood, R. F.; Westbrook, R. D.; Young, R. T.; Cleland, J. W.

1977-01-01

Normal isotopic silicon contains 3.05% of Si-30 which transmutes to P-31 after thermal neutron absorption, with a half-life of 2.6 hours. This reaction is used to introduce extremely uniform concentrations of phosphorus into silicon, thus eliminating the areal and spatial inhomogeneities characteristic of chemical doping. Annealing of the lattice damage in the irradiated silicon does not alter the uniformity of dopant distribution. Transmutation doping also makes it possible to introduce phosphorus into polycrystalline silicon without segregation of the dopant at the grain boundaries. The use of neutron transmutation doped (NTD) silicon in solar cell research and development is discussed.

Photo-induced current transient spectroscopy for high-resistivity neutron-transmutation-doped silicon

International Nuclear Information System (INIS)

Tokuda, Yutaka; Inoue, Yajiro; Usami, Akira

1987-01-01

Defects in high-resistivity neutron-transmutation-doped (NTD) silicon prior to annealing were studied by photo-induced current transient spectroscopy (PICTS). The thermal-neutron fluence was 9.5 x 10 17 cm -2 to give a resistivity of about 30 Ω after annealing, and the fast-neutron fluence was 9.5 x 10 16 cm -2 . Four traps with thermal emission activation energies of 0.15, 0.41. 0.47 and 0.50 eV were observed in NTD silicon. A trap with the thermal emission activation energy of 0.15 eV was considered to correspond to the divacancy. Although the clustered nature of the defects was observed, PICTS measurements suggest that the material state of high-resistivity NTD silicon is still crystalline and not amorphous. (author)

Transmutation of radioactive wastes: how and why?

International Nuclear Information System (INIS)

Patarin, L.

2004-01-01

After having evoked the natural or spontaneous transmutation of natural or artificial radioactive atoms, the author describes how this transmutation is technically obtained, indicates the two main families of atoms present in a used nuclear fuel and for which transmutation is to be investigated (long-lived fission residues or products, and transuranium elements) and of which the behaviour in neutron fluxes must be explored. He discusses the industrial means required for artificial transmutation. He discusses the interest of performing such a transmutation

Optimisation of the neutron source based on gas dynamic trap for transmutation of radioactive wastes

Science.gov (United States)

Anikeev, Andrey V.

2012-06-01

The Budker Institute of Nuclear Physics in collaboration with the Russian and foreign organizations develop the project of 14 MeV neutron source, which can be used for fusion material studies and for other application. The projected neutron source of plasma type is based on the plasma Gas Dynamic Trap (GDT), which is a special magnetic mirror system for plasma confinement. Presented work continues the subject of development the GDT-based neutron source (GDT-NS) for hybrid fusion-fission reactors. The paper presents the results of recent numerical optimization of such neutron source for transmutation of the long-lives radioactive wastes in spent nuclear fuel.

Neutron Transmutation Doped (NTD) germanium thermistors for sub-mm bolometer applications

Science.gov (United States)

Haller, E. E.; Itoh, K. M.; Beeman, J. W.

1996-01-01

Recent advances in the development of neutron transmutation doped (NTD) semiconductor thermistors fabricated from natural and controlled isotopic composition germanium are reported. The near ideal doping uniformity that can be achieved with the NTD process, the device simplicity of NTD Ge thermistors and the high performance of cooled junction field effect transistor preamplifiers led to the widespread acceptance of these thermal sensors in ground-based, airborne and spaceborne radio telescopes. These features made possible the development of efficient bolometer arrays.

Partitioning and Transmutation - Physics, Technology and Politics

International Nuclear Information System (INIS)

Gudowski, W.

2002-01-01

Nuclear reactions can be effectively used to destroy radio toxic isotopes through transmutation processes transforming those isotopes into less radio toxic or stable ones Spent nuclear fuel, a mixture of many isotopes with some of them being highly radio toxic for many hundred thousands of years, may be effectively transmuted through nuclear reactions with neutrons. In a dedicated, well designed transmutation system one can, in principle, reduce the radiotoxicity of the spent nuclear fuel to a level, which will require isolation from the biosphere for the period of time for which engineered barriers can be constructed and licensed (not more than 1-2 thousands of years). En effective transmutation process can not be achieved without a suitable partitioning. Only partitioning of the spent nuclear fuel into predetermined groups of elements makes possible an effective use of neutrons to transmute long-lived radioactive isotopes into short-lived or stable one. However, most of the chemical separation/partitioning processes are element- not isotope-specific, therefore the transmutation of the elements with an existing isotope composition is a typical alternative for transmutation processes. Isotope-specific separation is possible but still very expensive and technologically not matured

Neutron detectors for transmutation of radioactive waste: the state of the art

International Nuclear Information System (INIS)

Machrafi, R.

2002-01-01

We overview in short the neutron detectors currently used in the investigation of the transmutation of radioactive waste. Such detectors should comply with some specific requirements. In particular, they have to be small enough, non-expensive, easy in use, radiation-resistant and covering sufficiently large energy intervals. These conditions are met to the acceptable extent in the case of activation foils, gas detectors and solid track detectors, which are discussed briefly in our work

Transmutation performance analysis on coolant options in a hybrid reactor system design for high level waste incineration

Energy Technology Data Exchange (ETDEWEB)

Hong, Seong-Hee; Siddique, Muhammad Tariq; Kim, Myung Hyun, E-mail: mhkim@khu.ac.kr

2015-11-15

Highlights: • Waste transmutation performance was compared and analyzed for seven different coolant options. • Reactions of fission and capture showed big differences depending on coolant options. • Moderation effect significantly affects on energy multiplication, tritium breeding and waste transmutation. • Reduction of radio-toxicities of TRUs showed different trend to coolant choice from performance of waste transmutation. - Abstract: A fusion–fission hybrid reactor (FFHR) is one of the most attractive candidates for high level waste transmutation. The selection of coolant affects the transmutation performance of a FFHR. LiPb coolant, as a conventional coolant for a FFHR, has problems such as reduction in neutron economic and magneto-hydro dynamics (MHD) pressure drop. Therefore, in this work, transmutation performance is evaluated and compared for various coolant options such as LiPb, H{sub 2}O, D{sub 2}O, Na, PbBi, LiF-BeF{sub 2} and NaF-BeF{sub 2} applicable to a hybrid reactor for waste transmutation (Hyb-WT). Design parameters measuring performance of a hybrid reactor were evaluated by MCNPX. They are k{sub eff}, energy multiplication factor, neutron absorption ratio, tritium breeding ratio, waste transmutation ratio, support ratio and radiotoxicity reduction. Compared to LiPb, H{sub 2}O and D{sub 2}O are not suitable for waste transmutation because of neutron moderation effect. Waste transmutation performances with Na and PbBi are similar to each other and not different much from LiPb. Even though molten salt such as LiF-BeF{sub 2} and NaF-BeF{sub 2} is good for avoiding MHD pressure drop problem, waste transmutation performance is dropped compared with LiPb.

Transmutants and its behaviors in heavy irradiated AlN by reactor neutrons

International Nuclear Information System (INIS)

Atobe, Kozo; Tashiro, Tomonori; Honda, Makoto; Fukuoka, Noboru; Matsukawa, Tokuo; Okada, Moritami; Nakagawa, Masuo.

1997-01-01

Transmutant production effects on the sintered aluminum nitride have been studied by neutron heavy irradiation using X-ray photoelectron spectroscopy analysis. The specimens are irradiated with fast neutrons in the ranges of 1.0x10 17 - 1.2x10 20 n/cm 2 . For high fluences (>10 18 n/cm 2 ), XPS observations show Si2s (153.8 eV) and Si2p (103.3 eV) peaks in XPS spectrum. The depth profiles using Ar-ion sputtering and the chemical shift of the peak indicate that 28 Si induced by 27 Al (n,γ) 28 Al reaction and β-decay of 28 Al precipitates near surface as oxidized silicon. (author)

Object kinetic Monte Carlo model for neutron and ion irradiation in tungsten: Impact of transmutation and carbon impurities

Science.gov (United States)

Castin, N.; Bonny, G.; Bakaev, A.; Ortiz, C. J.; Sand, A. E.; Terentyev, D.

2018-03-01

We upgrade our object kinetic Monte Carlo (OKMC) model, aimed at describing the microstructural evolution in tungsten (W) under neutron and ion irradiation. Two main improvements are proposed based on recently published atomistic data: (a) interstitial carbon impurities, and their interaction with radiation-induced defects (point defect clusters and loops), are more accurately parameterized thanks to ab initio findings; (b) W transmutation to rhenium (Re) upon neutron irradiation, impacting the diffusivity of radiation defects, is included, also relying on recent atomistic data. These essential amendments highly improve the portability of our OKMC model, providing a description for the formation of SIA-type loops under different irradiation conditions. The model is applied to simulate neutron and ion irradiation in pure W samples, in a wide range of fluxes and temperatures. We demonstrate that it performs a realistic prediction of the population of TEM-visible voids and loops, as compared to experimental evidence. The impact of the transmutation of W to Re, and of carbon trapping, is assessed.

Efficiency Of Transuranium Nuclides Transmutation

International Nuclear Information System (INIS)

Kazansky, Yu.A.; Klinov, D.A.; Semenov, E.V.

2002-01-01

One of the ways to create a wasteless nuclear power is based on transmutation of spent fuel nuclides. In particular, it is considered that the radioactivity of the nuclear power wastes should be the same (or smaller), than radioactivity of the uranium and the thorium extracted from entrails of the Earth. The problem of fission fragments transmutation efficiency was considered in article, where, in particular, the concepts of transmutation factor and the ''generalised'' index of biological hazard of the radioactive nuclides were entered. The transmutation efficiency has appeared to be a function of time and, naturally, dependent on nuclear power activity scenario, from neutron flux, absorption cross-sections of the nuclides under transmutation and on the rate of their formation in reactors. In the present paper the efficiency of the transmutation of transuranium nuclides is considered

Nuclear waste transmutation

International Nuclear Information System (INIS)

Salvatores, M.; Girard, C.; Delpech, M.; Slessarev, I.; Tommasi, J.

1994-01-01

Waste management strategies foresee the use of a deep geological repository either for final disposal of irradiated fuel or, after reprocessing and reuse of U and Pu for final disposal of long-lived radio-active materials. In the second case, partitioning and transmutation of these materials can be considered to reduce the impact of radiation on man due to the storage. On the basis of the SPIN programme developed by CEA in this field, the main features of transmutation is presented. The goal to achieve and the criteria to use are quite difficult to establish. The rights para-meters to characterize the risk are the potential radiotoxicity in the the repository and the residual radiotoxicity at the outlet. Transmutation studies in CEA used the potential radiotoxicity which is based on well-known parameters and less precise hazardous factors. The second point to appreciate the trans- mutation interest is to dispose of a criteria for the radio-radiotoxicity reduction. As there is no general agreement, we try to have a toxicity as low as possible within reasonable technical limits. To reduce the long term radio- toxicity, Pu, minor actinides and some long-lived fission products have to be transmuted. To assess the feasibility of such trans-mutation in reactors or advanced systems, one has to consider constraints on neutronic balance, safety, fuel cycle, technology , economy. Taking in account the main conclusions of this analysis, parametric studies of homogeneous and heterogenous transmutation permit a choice of promising solutions. Goals are to use every long-lived element with a minimized production of other long- lived elements in order to obtain an appreciable radiotoxicity reduction. It implies multi recycling of Pu which favours fast neutron reactors and different strategies of multi recycling for Np, Am, Cm. Multi recycling makes the results strongly dependant of losses. Researches to obtain the high partitioning efficiency needed are in progress. Calculations

Development of long-lived radionuclide transmutation technology -Development of nuclear transmutation technology-

Energy Technology Data Exchange (ETDEWEB)

Lee, Myung Chan; Jung, Woo Tae; Koh, Duk Joon; Kim, Jung Doh; Kil, Choong Sub [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1995-07-01

Based on the performance assessment of current reactor nuclear design codes, CASMO-3, LEOPARD, CITATION could be used for the simulation of transmutation, but further improvements are required on the reliability of cross sections of MA or FP and the accuracy of burnup model. Our simulation results based on the calculation by using CASMO-3 and NEM-3D (developed at Seoul National University) showed that transmutation efficiency for Am was high but Np and Cm elements were found to be hard to transmute. In our calculation, micro depletion calculations with burnup variation were done separately. Possibility of MA and FP transmutation with hard and fast neutrons was reported to be greater but detail calculation will be done in next year. 44 figs, 31 tabs, 17 refs. (Author).

Role of (n,2n) reactions in transmutation of long-lived fission products

Energy Technology Data Exchange (ETDEWEB)

Apse, V. A.; Kulikov, G. G., E-mail: ggkulikov@mephi.ru; Kulikov, E. G. [National Research Nuclear University MEPhI (Moscow Engineering Physics Institute) (Russian Federation)

2016-12-15

The conditions under which (n,γ) and (n,2n) reactions can help or hinder each other in neutron transmutation of long-lived fission products (LLFPs) are considered. Isotopic and elemental transmutation for the main long-lived fission products, {sup 79}Se, {sup 93}Zr, {sup 99}Tc, {sup 107}Pd, {sup 126}Sn, {sup 129}I, and {sup 135}Cs, are considered. The effect of (n,2n) reactions on the equilibrium amount of nuclei of the transmuted isotope and the neutron consumption required for the isotope processing is estimated. The aim of the study is to estimate the influence of (n,2n) reactions on efficiency of neutron LLFP transmutation. The code TIME26 and the libraries of evaluated nuclear data ABBN-93, JEF-PC, and JANIS system are applied. The following results are obtained: (1) The effect of (n,2n) reactions on the minimum number of neutrons required for transmutation and the equilibrium amount of LLFP nuclei is estimated. (2) It is demonstrated that, for three LLFP isotopes ({sup 126}Sn, {sup 129}I, and {sup 135}Cs), (n,γ) and (n,2n) reactions are partners facilitating neutron transmutation. The strongest effect of (n,2n) reaction is found for {sup 126}Sn transmutation (reduction of the neutron consumption by 49% and the equilibrium amount of nuclei by 19%).

LO-phonon and plasmon coupling in neutron-transmutation-doped GaAs

International Nuclear Information System (INIS)

Kuriyama, K.; Sakai, K.; Okada, M.

1996-01-01

Coupling between the longitudinal-optic (LO) phonon mode and the longitudinal plasma mode in neutron-transmutation-doped (NTD) semi-insulating GaAs was studied using Raman-scattering spectroscopy and a Fourier-transform infrared spectrometer. When the electron concentration due to the activation of NTD impurities (Ge Ga and Se As ) approaches ∼8x10 16 cm -3 , the LO-phonon endash plasmon coupling is observed. This behavior is consistent with the free-electron absorption due to the activation of NTD impurities in samples annealed above 600 degree C. copyright 1996 The American Physical Society

Transmutation of actinide 237Np with a fusion reactor and a hybrid reactor

International Nuclear Information System (INIS)

Feng, K.M.; Huang, J.H.

1994-01-01

The use of fusion reactors to transmute fission reactor wastes to stable species is an attractive concept. In this paper, the feasibility of transmutation of the long-lived actinide radioactive waste Np-237 with a fusion reactor and a hybrid reactor has been investigated. A new waste management concept of burning HLW (High Level Waste), utilizing released energy and converting Np-237 into fissile fuel Pu-239 through transmutation has been adopted. The detailed neutronics and depletion calculation of waste inventories was carried out with a modified version of one-dimensional neutron transport and burnup calculation code system BISON1.5 in this study. The transmutation rate of Np with relationship to neutron wall loading, Pu and Np with relationship to neutron wall load, Pu and Np concentration in the transmutation zone have been explored as well as relevant results are also given

Study on the LLFPs transmutation in a super-critical water-cooled fast reactor

International Nuclear Information System (INIS)

Lu Haoliang; Ishiwatari, Yuki; Oka, Yoshiaki

2011-01-01

Research highlights: → Transmutation of LLFPs with a super-criticial water cooled fast reactor. → Transmutation of iodine and cesium without the isotopic separation. → The transmuted isotope was mixed with UO 2 to reduce the effect of self-shielding. → A weak neutron moderator Al 2 O 3 was used to suppress the creation of 135 Cs from 133 Cs. - Abstract: The performance of the super-critical water-cooled fast reactor (Super FR) for the transmutation treatment of long-lived fission products (LLFPs) was evaluated. Two regions with the soft neutron spectrum, which is of great benefit to the LLFPs transmutation, can be utilized in the Super FR. First region is in the blanket assembly due to the ZrH 1.7 layer which was utilized to slow down the fast neutrons to achieve a negative void reactivity. Second region is in the reflector region of core like other metal-cooled fast reactors. The LLFPs selected in the transmutation analysis include 99 Tc, 129 I and 135 Cs discharged from LWR or fast reactor. Their isotopes, such as 127 I, 133 Cs, 134 Cs and 137 Cs were also considered to avoid the separation. By loading the isotopes ( 99 Tc or 127 I and 129 I) in the blanket assembly and the reflector region simultaneously, the transmutation rates of 5.36%/GWe year and 2.79%/GWe year can be obtained for 99 Tc and 129 I, respectively. The transmuted amounts of 99 Tc and 129 I are equal to the yields from 11.8 and 6.2 1000 MWe-class PWRs. Because of the very low capture cross section of 135 Cs and the effect of other cesium isotopes, 135 Cs was loaded with three rings of assemblies in the reflector region to make the transmuted amount be larger than the yields of two 1000 MWe-class PWRs. Based on these results, 99 Tc and 129 I can be transmuted conveniently and higher transmutation performance can be obtained in the Super FR. However, the transmutation of 135 Cs is very difficult and the transmuted amount is less than that produced by the Super FR. It turns out that the

Study of radioactive impurities in neutron transmutation doped germanium

Energy Technology Data Exchange (ETDEWEB)

Mathimalar, S.; Dokania, N.; Singh, V. [India-based Neutrino Observatory, Tata Institute of Fundamental Research, Mumbai 400 005 (India); Homi Bhabha National Institute, Anushaktinagar, Mumbai 400 094 (India); Nanal, V., E-mail: nanal@tifr.res.in [Department of Nuclear and Atomic Physics, Tata Institute of Fundamental Research, Mumbai 400 005 (India); Pillay, R.G. [Department of Nuclear and Atomic Physics, Tata Institute of Fundamental Research, Mumbai 400 005 (India); Shrivastava, A. [Nuclear Physics Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Jagadeesan, K.C.; Thakare, S.V. [Isotope Production and Applications Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India)

2015-02-21

A program to develop low temperature (mK) sensors with neutron transmutation doped Ge for rare event studies with a cryogenic bolometer has been initiated. For this purpose, semiconductor grade Ge wafers are irradiated with thermal neutron flux from Dhruva reactor at Bhabha Atomic Research Centre (BARC), Mumbai. Spectroscopic studies of irradiated samples have revealed that the environment of the capsule used for irradiating the sample leads to significant levels of {sup 65}Zn, {sup 110m}Ag and {sup 182}Ta impurities, which can be reduced by chemical etching of approximately ∼50μm thick surface layer. From measurements of the etched samples in the low background counting setup, activity due to trace impurities of {sup 123}Sb in bulk Ge is estimated to be ∼1Bq/g after irradiation. These estimates indicate that in order to use the NTD Ge sensors for rare event studies, a cooldown period of ∼2 years would be necessary to reduce the radioactive background to ≤1mBq/g.

Transmutation of fission products through accelerator

International Nuclear Information System (INIS)

Nakamura, H.; Tani, S.; Takahashi, T.; Yamamura, O.

1995-01-01

The transmutation of fission products through particle accelerators has been studied under the OMEGA program. The photonuclear reaction has also been investigated to be applied to transmuting long-lived fission products, such as Cesium and Strontium, which have difficulties on reaction with neutrons due to its so small cross section. It is applicable for the transmutation if the energy balance can be improved with a monochromatic gamma rays in the range of the Giant Dipole Resonance generated through an excellent high current electron linear accelerator. The feasibility studies are being conducted on the transmutation system using it through an electron accelerator. (authors)

Transmutants and its behaviors in heavy irradiated AlN by reactor neutrons

Energy Technology Data Exchange (ETDEWEB)

Atobe, Kozo; Tashiro, Tomonori; Honda, Makoto; Fukuoka, Noboru; Matsukawa, Tokuo [Naruto Univ. of Education, Tokushima (Japan). Faculty of Science; Okada, Moritami; Nakagawa, Masuo

1997-01-01

Transmutant production effects on the sintered aluminum nitride have been studied by neutron heavy irradiation using X-ray photoelectron spectroscopy analysis. The specimens are irradiated with fast neutrons in the ranges of 1.0x10{sup 17} - 1.2x10{sup 20} n/cm{sup 2}. For high fluences (>10{sup 18} n/cm{sup 2}), XPS observations show Si2s (153.8 eV) and Si2p (103.3 eV) peaks in XPS spectrum. The depth profiles using Ar-ion sputtering and the chemical shift of the peak indicate that {sup 28}Si induced by {sup 27}Al (n,{gamma}) {sup 28}Al reaction and {beta}-decay of {sup 28}Al precipitates near surface as oxidized silicon. (author)

Nuclear transmutation by flux compression

International Nuclear Information System (INIS)

Seifritz, W.

2001-01-01

A new idea for the transmutation of minor actinides, long (and even short) lived fission products is presented. It is based an the property of neutron flux compression in nuclear (fast and/or thermal) reactors possessing spatially non-stationary critical masses. An advantage factor for the burn-up fluence of the elements to be transmuted in the order of magnitude of 100 and more is obtainable compared with the classical way of transmutation. Three typical examples of such transmuters (a subcritical ringreactor with a rotating reflector, a sub-critical ring reactor with a rotating spallation source, the socalled ''pulsed energy amplifier'', and a fast burn-wave reactor) are presented and analysed with regard to this purpose. (orig.) [de

Transmutation of high-level radioactive waste - Perspectives

CERN Document Server

Junghans, Arnd; Grosse, Eckart; Hannaske, Roland; Kögler, Toni; Massarczyk, Ralf; Schwengner, Ronald; Wagner, Andreas

2014-01-01

In a fast neutron spectrum essentially all long-lived actinides (e.g. Plutonium) undergo fission and thus can be transmuted into generally short lived fission products. Innovative nuclear reactor concepts e.g. accelerator driven systems (ADS) are currently in development that foresee a closed fuel cycle. The majority of the fissile nuclides (uranium, plutonium) shall be used for power generation and only fission products will be put into final disposal that needs to last for a historical time scale of only 1000 years. For the transmutation of high-level radioactive waste a lot of research and development is still required. One aspect is the precise knowledge of nuclear data for reactions with fast neutrons. Nuclear reactions relevant for transmutation are being investigated in the framework of the european project ERINDA. First results from the new neutron time-of-flight facility nELBE at Helmholtz-Zentrum Dresden-Rossendorf will be presented.

Transmutation of minor actinides in a spherical torus tokamak fusion reactor, FDTR

International Nuclear Information System (INIS)

Feng, K.M.; Zhang, G.S.; Deng, M.G.

2003-01-01

In this paper, a concept for the transmutation of minor actinide (MA) nuclear wastes based on a spherical torus (ST) tokamak reactor, FDTR, is put forward. A set of plasma parameters suitable for the transmutation blanket was chosen. The 2-D neutron transport code TWODANT, the 3-D Monte Carlo code MCNP/4B, the 1-D neutron transport and burn-up calculation code BISON3.0 and their associated data libraries were used to calculate the transmutation rate, the energy multiplication factor and the tritium breeding ratio of the transmutation blanket. The calculation results for the system parameters and the actinide series isotopes for different operation times are presented. The engineering feasibility of the center-post (CP) of FDTR has been investigated and the results are also given. A preliminary neutronics calculation based on an ST transmutation blanket shows that the proposed system has a high transmutation capability for MA wastes. (author)

The development and application of silicon neutron transmutation doping (NTD) technology in china

International Nuclear Information System (INIS)

Qiao Chenyang; Sun Zhiyong; Ke Guotu, Lu Cungang; Shen Feng; Chen Huiqiang

2009-01-01

The research and development history of silicon Neutron Transmutation Doping (NTD) technology and its applications at home and abroad are introduced in this paper. The advantages of NTD, compared with conventional technology of doping, are narrated. The principle of NTD as well as the implementation of the main procedures related to Si NTD is explained. The market demand tendency is prospected, and the advanced measures on NTD quality control are described. (authors)

Code ACTIVE for calculation of the transmutation, induced activity and decay heat in neutron irradiation

International Nuclear Information System (INIS)

Ioki, Kimihiro; Harada, Yuhei; Asami, Naoto.

1976-03-01

The computer code ACTIVE has been prepared for calculation of the transmutation rate, induced activity and decay heat. Calculations are carried out with activation chain and spatial distribution of neutron energy spectrum. The spatial distribution of secondary gamma-ray source due to the unstable nuclides is also obtainable. Special attension is paid to the short life decays. (auth.)

Radiation damages and electro-conductive characteristics of Neutron-Transmutation-Doped GaAs

Energy Technology Data Exchange (ETDEWEB)

Kuriyama, Kazuo; Sato, Masataka; Sakai, Kiyohiro [Hosei Univ., Koganei, Tokyo (Japan). Coll. of Engineering; Okada, Moritami

1996-04-01

Neutron Transmutation Doping (NTD) method made it possible to do homogeneous doping of impurities and to easily control the doping level. Thus, the method has been put into practice for some materials such as silicon. Here, the annealing behavior of anti-site defects generated in neutron-irradiated GaAs was studied. Electric activations of NTD-impurities were started around 550degC in P1 and P2 radiation fields, which were coincident with the beginning of extinction of electron trapping which was caused by anti-site defects due to fast neutron radiation. The electric resistivities of GaAs in neutron radiation fields; P1, P2 and P3 changed depending with the annealing temperature. The electric resistivities of GaAs in P1 and P2 fields indicate the presence of hopping conduction through radiation damages. The resistance of GaAs irradiated in P1 was smaller by nearly 2 orders than that of the untreated control. Further, the electric activation process for NTD-impurities was investigated using ESR and Raman spectroscopy. (M.N.)

Specific contributions of the Dutch progamme ''RAS'' towards accelerator-based transmutation

International Nuclear Information System (INIS)

Abrahams, K.; Franken, W.M.P.; Bultman, J.H.; Heil, J.A.; Koning, A.J.

1994-09-01

Accelerator-based transmutation is being studied by ECN within its general nuclear waste transmutation programme RAS. In this paper the following contributions are presented: (1) Evaluation of cross sections at intermediate energies, within an international frame given by NEA, (2) Cell calculations on the equilibration of transuranium actinides in thermal molten-salt transmuters, (3) Irradiation facilities at the European research reactor HFR in Petten, which have been constructed with the purpose to demonstrate and investigate the transmutation of waste in a high neutron flux, (4) Studies of accelerator-based neutron generating systems to transmute neptunium and technetium, (5) Comparison of several systems on the basis of criteria for successful nuclear waste-management. (orig.)

Evaluation of transmutation performance of long-lived fission products with a super fast reactor

International Nuclear Information System (INIS)

Lu, Haoliang; Han, Chiyoung; Oka, Yoshiaki; Ikejiri, Satoshi; Ishiwatari, Yuki

2009-01-01

The performance of the Super Fast Reactor for transmutation treatment of long-lived fission products (LLFPs) was evaluated. Two regions with soft neutron spectrum, which is of great benefit to the LLFPs transmutation, can be utilized in the Super Fast Reactor. First is in the blanket assembly due to the ZrH 1.7 layer which can slow down the fast neutrons. Second is in the reflector region of core like other metal-cooled fast reactors. The LLFPs selected of transmutation analysis include 99 Tc, 129 I and 135 Cs discharged from LWR. Their isotopes, such as 127 I, 133 Cs, 134 Cs and 137 Cs were also considered. By loading the isotopes ( 99 Tc or 127 I and 129 I) in the blanket assembly and the reflector region simultaneously, the transmutation rates of 5.36%/GWe·y and 2.79%/GWe.y can be obtained for 99 Tc and 129 I, respectively. The transmuted amounts of 99 Tc and 129 I are equal to the outputs from 11.8 and 6.2 1000MWe-class PWRs. Because of the very low capture cross section of 135 Cs and the effect of other cesium isotopes, 135 Cs was loaded with three rings of assemblies in the reflector region to make the transmuted amount be larger than the yields of two 1000MWe-class PWRs. Based on these results, 99 Tc and 129 I can be transmuted conveniently and higher transmutation performance can be obtained by the Super Fast Reactor. However, the transmutation of 135 Cs is very difficult and the transmuted amount is less than that produced by the Super Fast Reactor. It turns out that the 135 Cs transmutation is a challenge not only for the Super Fast Reactor but also for other commercial fast reactors. (author)

Neutronics safety analysis in severe transients of the dual-cooled waste transmutation blanket for the FDS-I

International Nuclear Information System (INIS)

Zheng, S.; Wu, Y.

2006-01-01

The conceptual design of the fusion-driven subcritical system FDS-I with the multifunctional subcritical dual-cooled waste transmutation (DWT) blanket proposed as a middle step toward the final application of fusion energy was presented previously. Safety is a key concern for the innovative conceptual system. The potential safety characteristic is expected as one of the advantages of FDS-I for the transmutation and incineration of nuclear waste compared with the critical reactor. With the intent of evaluating the inherent and passive safety features of FDS-I, the reactivity coefficients (e.g. the coolant density/void effect and the Doppler feedback), which are similar to those in critical reactors, and the kinetics quantities (e.g. neutron generation time and β eff ), which are influenced by the external neutron source of the source-driven system, are calculated and analyzed. In addition, the specific transient scenarios for FDS-I, which show the effects of the source power perturbation on the safety parameters, is presented

Spatial heterogeneity of tungsten transmutation in a fusion device

Science.gov (United States)

Gilbert, M. R.; Sublet, J.-Ch.; Dudarev, S. L.

2017-04-01

Accurately quantifying the transmutation rate of tungsten (W) under neutron irradiation is a necessary requirement in the assessment of its performance as an armour material in a fusion power plant. The usual approach of calculating average responses, assuming large, homogenised material volumes, is insufficient to capture the full complexity of the transmutation picture in the context of a realistic fusion power plant design, particularly for rhenium (Re) production from W. Combined neutron transport and inventory simulations for representative spatially heterogeneous high-resolution models of a fusion power plant show that the production rate of Re is strongly influenced by the surrounding local spatial environment. Localised variation in neutron moderation (slowing down) due to structural steel and coolant, particularly water, can dramatically increase Re production because of the huge cross sections of giant resolved resonances in the neutron-capture reaction of 186W at low neutron energies. Calculations using cross section data corrected for temperature (Doppler) effects suggest that temperature may have a relatively lesser influence on transmutation rates.

Transmutation of fission products and actinide waste at Hanford

Energy Technology Data Exchange (ETDEWEB)

Daemen, L.L.; Pitcher, E.J.; Russell, G.J. [Los Alamos National Laboratory, NM (United States)

1995-10-01

The authors studied the neutronics of an ATW system for the transmutation of the fission products ({sup 99}Tc in particular) and the type of actinide waste stored in several tanks at Hanford. The heart of the system is a highly-efficient neutron production target. It is surrounded by a blanket containing a moderator/reflector material, as well as the products to be transmuted. The fission products are injected into the blanket in the form of an aqueous solution in heavy water, whereas an aqueous actinides slurry is circulated in the outer part of the blanket. For the sake of definiteness, the authors focussed on {sup 99}Tc (the most difficult fission product to transmute), and {sup 239}Pu, {sup 237}Np, and {sup 241}Am. Because of the low thermal neutron absorption cross-section of {sup 99}Tc, considerable care and effort must be devoted to the design of a very efficient neutron source.

Detailed investigation of neutron emitters in the transmutation of Minor Actinides

Energy Technology Data Exchange (ETDEWEB)

Letourneau, A.; Bringer, O.; Dupont, E.; Panebianco, S.; Veyssiere, Ch. [CEA/Saclay/DSM/IRFU - Gif-sur-Yvette (France); Al Mahamid, I. [Wadsworth Center, New York State Department of Health, Albany, NY 12201 (United States); Chartier, F. [CEA/Saclay/DEN/DPC/SECR - Gif-sur-Yvette (France); Mutti, P. [Institut Laue-Langevin, Grenoble (France); Oriol, L. [CEA/Cadarache/DEN/DER/SPEX - Saint-Paul-lez-Durances (France)

2008-07-01

The production of neutron emitters during the incineration process of minor actinides could be very penalizing for the reprocessing of the targets when transmuted in heterogeneous mode, either in dedicated systems (ADS) or in generation IV reactors. Therefore their production has to be carefully evaluated. The reliability of such evaluation really depends on nuclear data (capture and fission cross sections) and their accuracy. In this paper we present a work we have done to investigate the production of neutron emitters in the incineration of {sup 237}Np and {sup 241}Am targets in fast and thermal nuclear reactor concepts. The impact of nuclear data uncertainties on the production of those neutron-emitters was evaluated by sensitivity calculations. The reduction for some of these uncertainties in the thermal energy region was done by measuring more precisely the {sup 244}Cm(n,gamma){sup 245}Cm, {sup 245}Cm(n,f) and {sup 249}Cf(n,gamma){sup 250}Cf capture cross sections at the Laue-Langevin Institute (ILL). It amounts to (15.6+-2.4) b for the first one, (1923+-49) b for the second and (389+-10) b for the third one. (authors)

Separation of actinides and their transmutation

International Nuclear Information System (INIS)

Bouchard, M.; Bathelier, M.; Cousin, M.

1978-08-01

Neutron irradiation of long-half-life actinides for transmutation into elements with shorter half-life is investigated as a means to reduce the long-term hazards of these actinides. The effectiveness of the method is analysed by applying it to fission product solutions from the first extraction cycle of fuel reprocessing plants. Basic principles, separation techniques and transmutation efficiencies are studied and discussed in detail

Comparative analysis of sub-critical transmutation reactor concepts

International Nuclear Information System (INIS)

Chang, S. H.

1997-01-01

The long-lived nuclear wastes have been substantially generated from the light water reactor for a few decades. The toxicity of these spent fuels will be higher than that of the uranium ore, even if those will be stored in the repository more than ten thousands. Hence the means of transmuting the key long-lived nuclear wastes, primarily the minor actinides, using a hybrid proton accelerator and subcritical transmutation reactor, are proposed. Until now, the representative concepts for a subcritical transmutation reactor are the Energy Amplifier, the OMEGA project, the ATW and the MSBR. The detailed concepts and the specifications are illustrated in Table 1. The design requirements for the subcritical transmutation reactor are the high transmutation rate of long-lived nuclear wastes, safety and economics. And to propose the subcritical transmutation reactor concepts, the coolant, the target material and fuel type are carefully considered. In these aspects, the representative concepts for a subcritical transmutation reactor in Table 1 have been surveyed. The requirements for a target and a coolant are the reliable, low maintenance operation and safe operation to minimize the wastes. The reliable, low maintenance operation and safe operation to minimize the wastes. The reliable coolant must have the low melting point, high heat capacity and excellent physical properties. And the target material must have high neutron yield for a given proton condition and easy heat removal capability. Therefore in respect with the above requirements, Pb-Bi is proposed as the coolant and the target material for the subcritical reactor. Because the neutron yield for a given proton energy increases linearly with mass number up to bismuth but in heavier elements spallation events sharply increase both the neutron and heat outputs, Pb-Bi meets not only such the requirements as the above for the coolant but also those for the coolant and target, the simplification of system can be achieved

Transmutation of technetium: results of the EFTTRA-T1 experiment

International Nuclear Information System (INIS)

Konings, R.J.M.; Stalios, A.D.; Walker, C.T.; Cocuaud, N.

1998-01-01

The transmutation of the fission product 99 Tc was studied by neutron irradiation in the High Flux Reactor at Petten. Six metallic rods of pure Tc, distributed over three capsules, were irradiated during eight reactor cycles to a total neutron fluence of about 2 x 10 26 m -2 . Metallographic examinations showed that no changes in the microstructure were visible after the irradiation. Electron probe microanalysis (EPMA) of the radial distribution of Ru, the product of the transmutation process, showed an increase from about 6% in the centre to 12-18% near the rim of the pellets. This effect is due to resonance-shielding of epithermal neutrons in the rim region. Mass spectrometric analysis of the pellet-average Ru concentration showed that the extent of transmutation is about 6-7%. (orig.)

Actinide and fission product separation and transmutation

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-07-01

The second international information exchange meeting on actinide and fission product separation and transmutation, took place in Argonne National Laboratory in Illinois United States, on 11-13 November 1992. The proceedings are presented in four sessions: Current strategic system of actinide and fission product separation and transmutation, progress in R and D on partitioning processes wet and dry, progress in R and D on transmutation and refinements of neutronic and other data, development of the fuel cycle processes fuel types and targets. (A.L.B.)

Current Status of the Transmutation Reactor Technology and Preliminary Evaluation of Transmutation Performance of the KALIMER Core

Energy Technology Data Exchange (ETDEWEB)

Hong, Ser Gi; Sim, Yoon Sub; Kim, Yeong Il; Kim, Young Gyum; Lee, Byung Woon; Song, Hoon; Lee, Ki Bog; Jang, Jin Wook; Lee, Dong Uk

2005-08-15

Recently the most countries using the nuclear power plants for electricity generation have been faced with the problem of the preparation of the repository for the disposition of the nuclear waste generated from LWR. It was well-known that the issues related with long term risk of the radioactive wastes for the future generations are due only to 1% of the total waste. This small fraction of 1% consists of transuranic (TRU) nuclides such as Pu, Np, Am, Cm and the long lived fission products such as Tc and I. For the transuranic (TRU) nuclides, their half lives range from several years to several hundred thousands years and hence their radioactive toxicity can be lasted over very long time period. This has made the change of the rule of the fast spectrum reactor from the economical use of uranium resource through breeding to the reduction of the nuclear waste through the transmutation. The purpose of this study is to obtain the basic knowledge on the nuclear transmutation technology and to suggest the technical solution ways for the future technology development and enhancement through a survey of the state-of-art of the international research on the nuclear transmutation. The increase of the transmutation rate requires the reduction of the breeding ratio. In fact, the transmutation rate is determined by the breeding ratio. The reduction of the breeding ratio can be achieved by reducing the U-238 content in fuel or increasing the neutron leakage through core boundary or absorbing the neutrons by using some absorbers. However, the reduction of the U-238 content results in the degradation of the fuel Doppler coefficient that is one of the most important safety-related parameters and the reduction of the effective delayed neutron fraction that is related with the controllability of the reactor core. Also, the increase of the transmutation rate can lead to the increase of the coolant void reactivity worth unless some ways to reduce the coolant void reactivity are not

Transmutation of high-level radioactive waste by a charged particle accelerator

International Nuclear Information System (INIS)

Takahashi, Hiroshi.

1993-01-01

Transmutation of minor actinides and fission products using proton accelerators has many advantages over a transmutor operated in a critical condition. The energy required for this transmutation can be reduced by multiplying the spallation neutrons in a subcritical assembly surrounding the spallation target. The authors have studied the relation between the energy requirements and the multiplication factor, k, of the subcritical assembly, while varying the range of several parameters in the spallation target. A slightly subcritical reactor is superior to a reactor with large subcriticality in the context of the energy requirement of a small proton accelerator, the extent of radiation damage, and other safety problems. To transmute the fission products, the transmutor reactor must have a good neutron economy, which can be provided by a transmutor operated by a proton accelerator. The paper discusses the use of minor actinides to improve neutronics characteristics, such as a long fuel burn-up rather than simply transmuting this valuable material

Experience gained during 10 years transmutation experiments in Dubna

Science.gov (United States)

Zamani, M.; Fragopoulou, M.; Manolopoulou, M.; Stoulos, S.; Brandt, R.; Westmeier, W.; Krivopustov, M.; Sosnin, A.; Golovatyuk, S.

2006-05-01

Transmutation, the procedure of transforming long-lived radioactive isotopes into stable or short-lived, was proposed for reducing the amount of radioactive waste resulting from technological applications of nuclear fission. The Accelerator Driven Systems (ADS) provide the possibility to generate intense neutron spectrum yielding in an effective transmutation of unwanted isotopes. Such experiments are being carried out for the last 10 years in Synchrophasotron / Nuclotron accelerators at the Veksler-Baldin Laboratory of High Energies of the Joint Institute for Nuclear Research in Dubna, Russia. Thick Pb and Pb-U targets, surrounded by moderators, have been irradiated by protons in the energy range of 0.5-7.4 GeV. Neutron fluence measurements have been performed by different techniques of passive detectors (neutron activation detectors, solid state nuclear track detectors). Transmutation of 129I, 237Np, 239Pu was studied. The results of these experiments are presented and discussed.

Energy Production and Transmutation of Nuclear Waste by Accelerator Driven Systems

Science.gov (United States)

Zhivkov, P. K.

2018-05-01

There is a significant amount of highly radiotoxic long-life nuclear waste (NW) produced by NPP (Nuclear Power Plants). Transmutation is a process which transforms NW into less radiotoxic nuclides with a shorter period of half-life by spallation neutrons or radiative capture of neutrons produced by ADS (Accelerator Driven System). In the processes of transmutation new radioactive nuclides are produced. ADS is big energy consumer equipment. It is a method for production of a high-flux and high-energy neutron field. All these processes occur in ADS simultaneously. ADS is able to transmute actinides and produce energy simultaneously. The article considers the energy production problems in ADS. Several ideas are developed regarding the solution of the global energy supply.

Transmutation of radioactive nuclear waste

International Nuclear Information System (INIS)

Toor, A; Buck, R

2000-01-01

radioactive elements into other radioactive isotopes with much shorter half-lives. Transmutation of both RNW components using neutrons has been discussed and studied over the past four decades. Most transmutation studies have examined the feasibility of using neutron-induced reactions where the neutrons would be provided by accelerator-based spallation neutron sources, tokamak fusion reactors, sub-critical fission reactors and other novel concepts. Studies have shown that all proposed transmutation processes to treat RNW using neutron reactions are deficient or marginal at best from the point of view of energy consumption and/or cost. We suggest an alternative approach that has not been considered to date: the transmutation of RNW elements using high-energy photons or gamma rays. The photo-disintegration of RNW may provide an effective way to treat reprocessed waste; waste that has been chemically separated or the residual waste left over after neutron processing. Photo-disintegration is attractive in that any isotope can be transmuted. This approach is now potentially practical because of the development of micropole undulators (MPUs) that allow us to use small storage rings to economically generate photons with gamma-ray energies and to tune these ''gamma rays'' to the peak of the cross-section resonance for various RNW elements. Because the cross sections for all RNW nuclei have a broad peak with the maximum in the 12-18 MeV range, a single MPU could be used to treat both actinide and fission fragment components of RNW. The goal of this study is to make estimates of the reaction rates and energy efficiency of the transmutation of typical RNW elements using gamma rays to establish whether or not gamma-ray transmutation should be examined as a viable alternative solution to RNW warranting further study

Application of activation methods on the Dubna experimental transmutation set-ups.

Science.gov (United States)

Stoulos, S; Fragopoulou, M; Adloff, J C; Debeauvais, M; Brandt, R; Westmeier, W; Krivopustov, M; Sosnin, A; Papastefanou, C; Zamani, M; Manolopoulou, M

2003-02-01

High spallation neutron fluxes were produced by irradiating massive heavy targets with proton beams in the GeV range. The experiments were performed at the Dubna High Energy Laboratory using the nuclotron accelerator. Two different experimental set-ups were used to produce neutron spectra convenient for transmutation of radioactive waste by (n,x) reactions. By a theoretical analysis neutron spectra can be reproduced from activation measurements. Thermal-epithermal and fast-super-fast neutron fluxes were estimated using the 197Au, 238U (n,gamma) and (n,2n) reactions, respectively. Depleted uranium transmutation rates were also studied in both experiments.

Transmutation of 126Sn in spallation targets of accelerator-driven systems

International Nuclear Information System (INIS)

Han, Chi Young; Saito, Masaki; Sagara, Hiroshi

2009-01-01

The practical feasibility of 126 Sn transmutation in spallation targets of accelerator-driven systems was evaluated from the viewpoints of accumulation of radioactive spallation products and neutron production as well as transmutation amount of 126 Sn. A cylindrical liquid 126 Sn target whose length depends on proton beam energy was described, based on a Pb-Bi target design of accelerator-driven system being developed in JAEA. A proton beam of 1.5 GeV-20 mA was estimated to give the transmutation rate of 126 Sn 6.4 kg/yr, which corresponds to the amount of 126 Sn annually discharged in 27 LWRs of 1 GWt and 33 GWd/THM. The equilibrium radioactivity of spallation products would reach 9% of that of 126 Sn transmuted in the spallation target, and the equilibrium toxicity would be just 3%. Some parametric analyses showed that the effective half-life of 126 Sn could be reduced through a proper reduction of the target size. The 126 Sn target was calculated to produce 40 neutrons per proton of 1.5 GeV and give a neutron spectrum very similar to that of the reference Pb-Bi target. As a result, the transmutation of 126 Sn in the spallation target has a high feasibility in terms of better transmutation performance and comparable target performance. (author)

Neutron-induced transmutation reactions in Np-237, Pu-238, and Pu-239 at the massive natural uranium spallation target

Czech Academy of Sciences Publication Activity Database

Závorka, L.; Adam, Jindřich; Baldin, A. A.; Čaloun, Pavel; Chilap, V. V.; Furman, W.; Kadykov, M. G.; Khushvaktov, J.; Pronskikh, V. S.; Solnyshkin, A. A.; Sotnikov, V.; Stegailov, V. I.; Suchopár, Martin; Tsoupko-Sitnikov, V. M.; Tyutyunnikov, S. I.; Voronko, V.; Vrzalová, Jitka

2015-01-01

Roč. 349, APR (2015), s. 31-38 ISSN 0168-583X R&D Projects: GA MŠk LG14004 Institutional support: RVO:61389005 Keywords : ADS * spent nuclear fuel * transmutation reaction * spallation neutrons Subject RIV: BG - Nuclear , Atomic and Molecular Physics, Colliders Impact factor: 1.389, year: 2015

Technical meeting on 'Review of solid and mobile fuels for partitioning and transmutation systems'. Working material

Energy Technology Data Exchange (ETDEWEB)

NONE

2003-07-01

The topics covered during the Meeting were divided into two Sessions. Session 1 - Qualification of Solid and Mobile Fuels delt with: Neutronic, fuel and material properties of a molten salt transmuter; and Preliminary analysis of transmutation fuels for KALIMER. Session 2 - Reactor Physics and Safety Characteristics of Transmutation Systems based on Solid and Mobile Fuel Types included the following: Activity in NEA for P and T area; IAEA activities in the area of partitioning and transmutation; The R and D activity in Brazil: A conceptual fast energy amplifier ADS cooled by helium double stata Th/U fuel cycle; Closed fuel cycle and contemporary tendencies of the nuclear facilities development; Current Russian activities in P and T area; Pyrochemical reprocessing and nuclear spent fuel disposal project; Fuel selection criteria specific for double stratum minor actinide burners.

Laser enhanced radioactive decay and selective transmutation of nuclear waste

International Nuclear Information System (INIS)

Saloman, R.; Aarnio, P.; Ala-Heikkila, J.; Hakola, A.; Santala, M.

2007-01-01

We have investigated narrow-band coherent laser radiation - ranging from visible to X- and to gamma-ray wave length region - and their interactions both directly with photon-nuclear couplings and indirectly through the photon-electron and electron-nucleus interactions. In particular we discuss various means of selective excitation of nuclear resonance states by narrowband lasers. During the relaxation process the active nucleus may return to its initial ground-state or find another final state. In the latter case the nucleus is transmuted into a state which may have beneficial properties for instance concerning radioactivity. One ideal case would be the destruction of long-lived nuclear waste isotopes into faster decaying ones. The essential presumption is that the excitation process is selective and efficient as regards background processes due to unwanted excitation channels of the primary isotope and due to other surrounding nuclides. The paper consists of 1) a short review of generating short-wave length coherent light sources, 2) a survey of potential photon-induced nuclear states and their decay channels, and 3) a determination of the selectivity of the transmutation process

Method to Reduce Long-lived Fission Products by Nuclear Transmutations with Fast Spectrum Reactors.

Science.gov (United States)

Chiba, Satoshi; Wakabayashi, Toshio; Tachi, Yoshiaki; Takaki, Naoyuki; Terashima, Atsunori; Okumura, Shin; Yoshida, Tadashi

2017-10-24

Transmutation of long-lived fission products (LLFPs: 79 Se, 93 Zr, 99 Tc, 107 Pd, 129 I, and 135 Cs) into short-lived or non-radioactive nuclides by fast neutron spectrum reactors without isotope separation has been proposed as a solution to the problem of radioactive wastes disposal. Despite investigation of many methods, such transmutation remains technologically difficult. To establish an effective and efficient transmutation system, we propose a novel neutron moderator material, yttrium deuteride (YD 2 ), to soften the neutron spectrum leaking from the reactor core. Neutron energy spectra and effective half-lives of LLFPs, transmutation rates, and support ratios were evaluated with the continuous-energy Monte Carlo code MVP-II/MVP-BURN and the JENDL-4.0 cross section library. With the YD 2 moderator in the radial blanket and shield regions, effective half-lives drastically decreased from 106 to 102 years and the support ratios reached 1.0 for all six LLFPs. This successful development and implementation of a transmutation system for LLFPs without isotope separation contributes to a the ability of fast spectrum reactors to reduce radioactive waste by consuming their own LLFPs.

Minor actinide transmutation in a board type sodium cooled breed and burn reactor core

International Nuclear Information System (INIS)

Zheng, Meiyin; Tian, Wenxi; Zhang, Dalin; Qiu, Suizheng; Su, Guanghui

2015-01-01

Highlights: • A 1250 MWt board type sodium cooled breed and burn reactor core is further designed. • MCNP–ORIGEN coupled code MCORE is applied to perform neutronics and depletion calculation. • Transmutation efficiency and neutronic safety parameters are compared under different MA weight fraction. - Abstract: In this paper, a board type sodium cooled breed and burn reactor core is further designed and applied to perform minor actinide (MA) transmutation. MA is homogeneously loaded in all the fuel sub-assemblies with a weight fraction of 2.0 wt.%, 4.0 wt.%, 6.0 wt.%, 8.0 wt.%, 10.0 wt.% and 12.0 wt.%, respectively. The transmutation efficiency, transmutation amount, power density distribution, neutron fluence distribution and neutronic safety parameters, such as reactivity, Doppler feedback, void worth and delayed neutron fraction, are compared under different MA weight fraction. Neutronics and depletion calculations are performed based on the self-developed MCNP–ORIGEN coupled code with the ENDF/B-VII data library. In the breed and burn reactor core, a number of breeding sub-assemblies are arranged in the inner core in a board type way (scatter load) to breed, and a number of absorbing sub-assemblies are arranged in the inner side of the outer core to absorb neutrons and reduce power density in this area. All the fuel sub-assemblies (ignition and breeding sub-assemblies) are shuffled from outside in. The core reached asymptotically steady state after about 22 years, and the average and maximum discharged burn-up were about 17.0% and 35.3%, respectively. The transmutation amount increased linearly with the MA weight fraction, while the transmutation rate parabolically varied with the MA weight fraction. Power density in ignition sub-assembly positions increased with the MA weight fraction, while decreased in breeding sub-assembly positions. Neutron fluence decreased with the increase of MA weight fraction. Generally speaking, the core reactivity and void

The possible transmutation of radioactive waste from nuclear reactors

International Nuclear Information System (INIS)

Harries, J.R.

1974-01-01

A nuclear reactor power program produces high level and long lived radioactive wastes. The high level activity is associated with fission products, but beyond 400 years the principal waste hazard is from transuranic elements produced in the reactor. Several schemes have been proposed for the transmutation of the problem isotopes into more easily handled isotopes. The neutron flux in a thermal reactor is not high enough to significantly reduce the longer lived fission product isotopes 90 Sr and 132 Gs, but the transuranic elements can be reduced by recycling through power reactors. The limitation on recycling of the transuranic elements is the separation process to remove trace quantities from the waste stream. In fast reactors the transuranic elements are the principal fuel and fast reactor waste contains only half as much 90 Sr as thermal reactors. However, the overall waste hazard is similar to thermal reactors. A sufficiently intense neutron flux for fission product transmutation could perhaps be produced by a spallation reactor driven by a proton linear accelerator or a controlled thermonuclear reactor. However, both concepts are still some years in the future. Transmutation by accelerator sources of protons, electrons of gammas tend to require more energy than neutron transmutation. (author)

Specific contributions of the Dutch programme {open_quotes}RAS{close_quotes} towards accelerator-based transmutation

Energy Technology Data Exchange (ETDEWEB)

Abrahams, K.; Franken, W.M.P.; Bultman, J.H. [Netherlands Energy Research Foundation (ECN), Petten (Netherlands)] [and others

1995-10-01

Accelerator-based transmutation is being studied by ECN within its general nuclear waste transmutation programme RAS. In this paper the following contributions are presented: (1) Evaluation of cross sections at intermediate energies, within an international frame given by NEA, (2) Cell calculations on the equilibration of transuranium actinides in thermal molten-salt transmuters, (3) Irradiation facilities at the European research reactor HFR in Petten, which have been constructed with the purpose to demonstrate and investigate the transmutation of waste in a high neutron flux, (4) Studies of accelerator-based neutron generating systems to transmute neptunium and technetium, (5) Comparison of several systems on the basis of criteria for successful nuclear waste-management.

A Study on the Thermal Neutron Filter for the Irradiation of Electronic Materials at HANARO

Energy Technology Data Exchange (ETDEWEB)

Yang, Seong Woo; Kim, Sung Ryul; Park, Seung Jae; Shin, Yoon Taeg; Cho, Man Soon; Cho, Kee Nam [KAERI, Daejeon (Korea, Republic of)

2016-05-15

The representative example is a technique of making the semiconductor with the transmutation using the pure Si. This NTD (Neutron Transmutation Doping) Si is used as a high-quality semiconductor because it has a uniform resistance. Likewise, the electronic materials are being investigated to improve the performance of material using the neutron irradiation method. The mechanism for reaction between the electronic materials and the neutrons depends on the energy of the neutron. Capturing reaction by thermal neutrons causes the transmutation and a lot of defects are made by fast neutrons. The study for the effect by such neutron energy is necessary to understand the performance improvement of the irradiated electronic materials. The thermal neutron filter was investigated to be used for the irradiation of electronic materials at HANARO. IP irradiation hole was selected and the irradiation device was designed. The analysis was conducted considering four candidate materials.

Evaluation on transmutation performance of minor actinides with high-flux BWR

International Nuclear Information System (INIS)

Setiawan, M.B.; Kitamoto, A.; Taniguchi, A.

2001-01-01

The performance of high-flux BWR (HFBWR) for burning and/or transmutation (B/T) treatment of minor actinides (MA) and long-lived fission products (LLFP) was discussed herein for estimating an advanced waste disposal with partitioning and transmutation (P and T). The concept of high-flux B/T reactor was based on a current 33 GWt-BWR, to transmute the mass of long-lived transuranium (TRU) to short-lived fission products (SLFP). The nuclide selected for B/T treatment was MA (Np-237, Am-241, and Am-243) included in the discharged fuel of LWR. The performance of B/T treatment of MA was evaluated by a new function, i.e. [F/T ratio], defined by the ratio of the fission rate to the transmutation rate in the core, at an arbitrary burn-up, due to all MA nuclides. According to the results, HFBWR could burn and/or transmute MA nuclides with higher fission rate than BWR, but the fission rate did not increase proportionally to the flux increment, due to the higher rate of neutron adsorption. The higher B/T fraction of MA would result in the higher B/T capacity, and will reduce the units of HFBWR needed for the treatment of a constant mass of MA. In addition, HFBWR had a merit of higher mass transmutation compared to the reference BWR, under the same mass loading of MA

Neutron and proton transmutation-activation cross section libraries to 150 MeV for application in accelerator-driven systems and radioactive ion beam target-design studies

International Nuclear Information System (INIS)

Koning, A.J.; Chadwick, M.B.; MacFarlane, R.E.; Mashnik, S.; Wilson, W.B.

1998-05-01

New transmutation-activation nuclear data libraries for neutrons and protons up to 150 MeV have been created. These data are important for simulation calculations of radioactivity, and transmutation, in accelerator-driven systems such as the production of tritium (APT) and the transmutation of waste (ATW). They can also be used to obtain cross section predictions for the production of proton-rich isotopes in (p,xn) reactions, for radioactive ion beam (RIB) target-design studies. The nuclear data in these libraries stem from two sources: for neutrons below 20 MeV, we use data from the European activation and transmutation file, EAF97; For neutrons above 20 MeV and for protons at all energies we have isotope production cross sections with the nuclear model code HMS-ALICE. This code applies the Monte Carlo Hybrid Simulation theory, and the Weisskopf-Ewing theory, to calculate cross sections. In a few cases, the HMS-ALICE results were replaced by those calculated using the GNASH code for the Los Alamos LA150 transport library. The resulting two libraries, AF150.N and AF150.P, consist of 766 nuclides each and are represented in the ENDF6-format. An outline is given of the new representation of the data. The libraries have been checked with ENDF6 preprocessing tools and have been processed with NJOY into libraries for the Los Alamos transmutation/radioactivity code CINDER. Numerous benchmark figures are presented for proton-induced excitation functions of various isotopes compared with measurements. Such comparisons are useful for validation purposes, and for assessing the accuracy of the evaluated data. These evaluated libraries are available on the WWW at: http://t2.lanl.gov/. 21 refs

Results from the TARC experiment: spallation neutron phenomenology in lead and neutron-driven nuclear transmutation by adiabatic resonance crossing.

CERN Document Server

Abánades, A; Andriamonje, Samuel A; Angelopoulos, Angelos; Apostolakis, Alcibiades J; Arnould, H; Belle, E; Bompas, C A; Brozzi, Delecurgo; Bueno, J; Buono, S; Carminati, F; Casagrande, Federico; Cennini, P; Collar, J I; Cerro, E; Del Moral, R; Díez, S; Dumps, Ludwig; Eleftheriadis, C; Embid, M; Fernández, R; Gálvez, J; García, J; Gelès, C; Giorni, A; González, E; González, O; Goulas, I; Heuer, R D; Hussonnois, M; Kadi, Y; Karaiskos, P; Kitis, G; Klapisch, Robert; Kokkas, P; Lacoste, V; Le Naour, C; Lèpez, C; Loiseaux, J M; Martínez-Val, J M; Méplan, O; Nifenecker, H; Oropesa, J; Papadopoulos, I M; Pavlopoulos, P; Pérez-Enciso, E; Pérez-Navarro, A; Perlado, M; Placci, A; Poza, M; Revol, Jean Pierre Charles; Rubbia, Carlo; Rubio, J A; Sakelliou, L; Saldaña, F; Savvidis, E; Schussler, F; Sirvent, C; Tamarit, J; Trubert, D; Tzima, A; Viano, J B; Vieira, S L; Vlachoudis, V; Zioutas, Konstantin; CERN. Geneva. SPS and LEP Division

2000-01-01

The results of the TARC experiment are summarized herewith, whose main purpose is to demonstrate the possibility of using Adiabatic Resonance Crossing (ARC) to destroy efficiently Long-Lived Fission Fragments (LLFFs) in accelerator-driven systems and to validate a new simulation developed in the framework of the Energy Amplifier programme. An experimental set-up was installed in a CERN PS proton beam line to study how neutrons, produced by spallation at relatively high energy (En * 1 MeV), slow down quasi adiabatically, with almost flat isolethargic energy distribution and reach the capture resonance energy of an element to be transmuted where they will have a high probability of being captured. Precision measurements of energy and space distributions of spallation neutrons (using 2.5 GeV/c and 3.5 GeV/c protons) slowing down in a 3.3 m x 3.3 m x 3 m lead volume and of neutron capture rates on LLFFs 99Tc, 129I, and several other elements were performed. An appropriate formalism and appropriate computational t...

Second International Conference on Neutron Transmutation Doping in Semiconductors

CERN Document Server

Neutron Transmutation Doping in Semiconductors

1979-01-01

This volume contains the invited and contributed papers presented at the Second International Conference on Neutron Transmutation Doping in Semiconductors held April 23-26, 1978 at the University of Missouri-Columbia. The first "testing of the waters" symposium on this subject was organized by John Cleland and Dick Wood of the Solid-State Division of Oak Ridge National Laboratory in April of 1976, just one year after NTD-silicon appeared on the marketplace. Since this first meeting, NTD-silicon has become established as the starting material for the power device industry and reactor irradiations are now measured in tens of tons of material per annum making NTD processing the largest radiation effects technology in the semiconductor industry. Since the first conference at Oak Ridge, new applications and irradiation techniques have developed. Interest in a second con­ ference and in publishing the proceedings has been extremely high. The second conference at the University of Missouri was attended by 114 perso...

The transmutation of americium: the Ecrix experiments in Phenix; Transmutation de l'americium: les experiences ecrix dans Phenix

Energy Technology Data Exchange (ETDEWEB)

Garnier, J C; Schmidt, N [CEA Cadarache, Dept. d' Etudes des Combustibles (DEC/SESC), 13 - Saint-Paul-lez-Durance (France); Croixmarie, Y; Ottaviani, J P [CEA Cadarache, Dept. d' Etudes des Combustibles (DEC/SPUA), 13 - Saint-Paul-lez-Durance (France); Varaine, F; Saint Jean, C de [CEA Cadarache, Dept. d' Etudes des Reacteurs (DER/SPRC), 13 - Saint-Paul-lez-Durance (France)

1999-07-01

The first americium transmutation experiment in a specific target in PHENIX will occur with the ECRIX-B and ECRIX-H experiments. Beside material testing, the objective is also to represent a concept of transmutation whose specificity is to enhance the kinetics of transmutation by using a moderated spectrum. The moderator materials will be {sup 11}B{sub 4}C and CaH{sub 2} for ECRIX-B and ECRIXH respectively, the irradiation conditions have been predicted for both the neutronics and thermal. The targets (MgO-AmO{sub X} pellets) are manufactured in the ATALANTE laboratory and the design is performed according to the PHENIX operating conditions. (authors)

PKA distributions: Contributions from transmutation products and from radioactive decay

Directory of Open Access Journals (Sweden)

M.R. Gilbert

2016-12-01

Full Text Available The neutrons generated in fusion plasmas interact with materials via nuclear reactions. The resulting transmutations and atomic displacements have life-limiting consequences for fusion reactor components. A detailed understanding of the production, evolution and material consequences of the damage created by cascades of atomic displacements requires, as a vital primary input, a complete description of the energy-spectrum of initial (prompt atomic displacement events (the primary knock on atoms or PKAs produced by direct neutron nuclear interactions. There is also the possibility that the radionuclides produced under transmutation will create further PKAs as they decay, and so the rate of these must also be quantified. This paper presents the latest results from the analysis of PKA spectra under neutron irradiation, focussing particularly on the variation in PKA distributions due to changes in composition under transmutation, but also on the PKA contributions from radioactive decay of materials that become activated under irradiation.

Minor actinide transmutation on PWR burnable poison rods

International Nuclear Information System (INIS)

Hu, Wenchao; Liu, Bin; Ouyang, Xiaoping; Tu, Jing; Liu, Fang; Huang, Liming; Fu, Juan; Meng, Haiyan

2015-01-01

Highlights: • Key issues associated with MA transmutation are the appropriate loading pattern. • Commercial PWRs are the only choice to transmute MAs in large scale currently. • Considerable amount of MA can be loaded to PWR without disturbing k eff markedly. • Loading MA to PWR burnable poison rods for transmutation is an optimal loading pattern. - Abstract: Minor actinides are the primary contributors to long term radiotoxicity in spent fuel. The majority of commercial reactors in operation in the world are PWRs, so to study the minor actinide transmutation characteristics in the PWRs and ultimately realize the successful minor actinide transmutation in PWRs are crucial problem in the area of the nuclear waste disposal. The key issues associated with the minor actinide transmutation are the appropriate loading patterns when introducing minor actinides to the PWR core. We study two different minor actinide transmutation materials loading patterns on the PWR burnable poison rods, one is to coat a thin layer of minor actinide in the water gap between the zircaloy cladding and the stainless steel which is filled with water, another one is that minor actinides substitute for burnable poison directly within burnable poison rods. Simulation calculation indicates that the two loading patterns can load approximately equivalent to 5–6 PWR annual minor actinide yields without disturbing the PWR k eff markedly. The PWR k eff can return criticality again by slightly reducing the boric acid concentration in the coolant of PWR or removing some burnable poison rods without coating the minor actinide transmutation materials from PWR core. In other words, loading minor actinide transmutation material to PWR does not consume extra neutron, minor actinide just consumes the neutrons which absorbed by the removed control poisons. Both minor actinide loading patterns are technically feasible; most importantly do not need to modify the configuration of the PWR core and

Study of minor actinides transmutation in heavy water cooled tight-pitch lattice

International Nuclear Information System (INIS)

Xu Xiaoqin; Shiroya, S.

2002-01-01

Minor actinides inhere long half-life and high toxicity. It is an alternative technical pathway and helpful for reducing environmental impact to incinerate minor actinides in spent fuel of nuclear power plants. Because of its high neutron, γ and β emitting rates and heat generation rate, it is necessary to imply more severe control and shielding techniques in the chemical treatment and fabrication. From economic view-point, it is suitable to transmute minor actinides in concentrated way. A technique for MA transmutation by heavy water cooled tight-pitch lattice system is proposed, and calculated with SRAC95 code system. It is shown that tight-pitch heavy water lattice can transmute MA effectively. The accelerator-driven subcritical system is practical for MA transmutation because of its low fraction of effective delay neutrons

System and safety studies of accelerator driven transmutation systems. Annual report 1997

International Nuclear Information System (INIS)

Wallenius, J.; Carlsson, Johan; Gudowski, W.

1997-12-01

In November 1996, SKB started financing of the project ''System and safety studies of accelerator driven transmutation systems and development of a spallation target''. The aim of the project was stated as: 1) Development of a complete code for simulation of transmutation processes in an accelerator driven system. Application of the code for analysis of neutron flux, transmutation rates, reactivity changes, toxicity and radiation damages in the transmutation core. 2) Build up of competence regarding issues related to spallation targets development of research activities regarding relevant material issues. Performing of basic experiments in order to investigate the adequacy of using the spallation target as a neutron source for a transmutation system, and participation in the planning and implementation of an international demonstration-experiment. In the present report, activities within the framework of the project performed at the department of Nuclear and Reactor Physics at the Royal Institute of Technology during 1997, are accounted for

System and safety studies of accelerator driven transmutation systems. Annual report 1997

Energy Technology Data Exchange (ETDEWEB)

Wallenius, J.; Carlsson, Johan; Gudowski, W. [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Nuclear and Reactor Physics

1997-12-01

In November 1996, SKB started financing of the project ``System and safety studies of accelerator driven transmutation systems and development of a spallation target``. The aim of the project was stated as: 1) Development of a complete code for simulation of transmutation processes in an accelerator driven system. Application of the code for analysis of neutron flux, transmutation rates, reactivity changes, toxicity and radiation damages in the transmutation core. 2) Build up of competence regarding issues related to spallation targets development of research activities regarding relevant material issues. Performing of basic experiments in order to investigate the adequacy of using the spallation target as a neutron source for a transmutation system, and participation in the planning and implementation of an international demonstration-experiment. In the present report, activities within the framework of the project performed at the department of Nuclear and Reactor Physics at the Royal Institute of Technology during 1997, are accounted for. 13 refs, 6 figs.

System and safety studies of accelerator driven transmutation systems. Annual report 1999

International Nuclear Information System (INIS)

Gudowski, Waclaw; Wallenius, Jan; Eriksson, Marcus; Carlsson, Johan; Seltborg, Per; Tucek, Kamil

2000-05-01

In 1996, SKB commenced funding of the project 'System and safety studies of accelerator driven transmutation systems and development of a spallation target'. The aim of the project was stated as: Development of a complete code for simulation of transmutation processes in an accelerator driven system. Application of the code for analysis of neutron flux, transmutation rates, reactivity changes, toxicity and radiation damages in the transmutation core. Build up of competence regarding issues related to spallation targets, development of research activities regarding relevant material issues. Performing of basic experiments in order to investigate the adequacy of using the spallation. target as a neutron source for a transmutation system, and participation in the planning and implementation of an international demonstration experiment. In the present report, activities within and related to the framework of the project, performed at the department of Nuclear and Reactor Physics at the Royal Institute of Technology during 1999, are accounted for

System and safety studies of accelerator driven transmutation systems. Annual report 1999

Energy Technology Data Exchange (ETDEWEB)

Gudowski, Waclaw; Wallenius, Jan; Eriksson, Marcus; Carlsson, Johan; Seltborg, Per; Tucek, Kamil [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Nuclear and Reactor Physics

2000-05-01

In 1996, SKB commenced funding of the project 'System and safety studies of accelerator driven transmutation systems and development of a spallation target'. The aim of the project was stated as: Development of a complete code for simulation of transmutation processes in an accelerator driven system. Application of the code for analysis of neutron flux, transmutation rates, reactivity changes, toxicity and radiation damages in the transmutation core. Build up of competence regarding issues related to spallation targets, development of research activities regarding relevant material issues. Performing of basic experiments in order to investigate the adequacy of using the spallation. target as a neutron source for a transmutation system, and participation in the planning and implementation of an international demonstration experiment. In the present report, activities within and related to the framework of the project, performed at the department of Nuclear and Reactor Physics at the Royal Institute of Technology during 1999, are accounted for.

Sensitivity to Nuclear Data and Neutron Source Type in Calculations of Transmutation Capabilities of the Energy Amplifier Demonstration Facility

International Nuclear Information System (INIS)

Dahlfors, Marcus

2003-05-01

This text is a summary of two studies the author has performed within the field of 3-D Monte Carlo calculations of Accelerator Driven Systems (ADS) for transmutation of nuclear waste. The simulations were carried out with the state-of-the-art computer code package EA-MC, developed by C. Rubbia and his group at CERN. The concept studied is ANSALDOs 80 MWth Energy Amplifier Demonstration Facility based on classical MOX-fuel technology and on molten Lead-Bismuth Eutectic cooling. A review of neutron cross section sensitivity in numerical calculations of an ADS and a comparative assessment relevant to the transmutation efficiency of plutonium and minor actinides in fusion/fission hybrids and ADS are presented

Sensitivity to Nuclear Data and Neutron Source Type in Calculations of Transmutation Capabilities of the Energy Amplifier Demonstration Facility

Energy Technology Data Exchange (ETDEWEB)

Dahlfors, Marcus

2003-05-01

This text is a summary of two studies the author has performed within the field of 3-D Monte Carlo calculations of Accelerator Driven Systems (ADS) for transmutation of nuclear waste. The simulations were carried out with the state-of-the-art computer code package EA-MC, developed by C. Rubbia and his group at CERN. The concept studied is ANSALDOs 80 MWth Energy Amplifier Demonstration Facility based on classical MOX-fuel technology and on molten Lead-Bismuth Eutectic cooling. A review of neutron cross section sensitivity in numerical calculations of an ADS and a comparative assessment relevant to the transmutation efficiency of plutonium and minor actinides in fusion/fission hybrids and ADS are presented.

Minor actinide transmutation using minor actinide burner reactors

International Nuclear Information System (INIS)

Mukaiyama, T.; Yoshida, H.; Gunji, Y.

1991-01-01

The concept of minor actinide burner reactor is proposed as an efficient way to transmute long-lived minor actinides in order to ease the burden of high-level radioactive waste disposal problem. Conceptual design study of minor actinide burner reactors was performed to obtain a reactor model with very hard neutron spectrum and very high neutron flux in which minor actinides can be fissioned efficiently. Two models of burner reactors were obtained, one with metal fuel core and the other with particle fuel core. Minor actinide transmutation by the actinide burner reactors is compared with that by power reactors from both the reactor physics and fuel cycle facilities view point. (author)

Assessment of the transmutation capability an accelerator driven system cooled by lead bismuth eutectic alloy

International Nuclear Information System (INIS)

Bianchi, F.; Peluso, V.; Calabrese; Chen, X.; Maschek, W.

2007-01-01

1. PURPOSE The reduction of long-lived fission products (LLFP) and minor actinides (MA) is a key point for the public acceptability and economy of nuclear energy. In principle, any nuclear fast reactor is able to burn and transmute MA, but the amount of MA content has to be limited a few percent, having unfavourable consequences on the coolant void reactivity, Doppler effect, and delayed neutron fraction, and therefore on the dynamic behaviour and control. Accelerator Driven Systems (ADS) are instead able to safely burn and/or transmute a large quantity of actinides and LLFP, as they do not rely on delayed neutrons for control or power change and the reactivity feedbacks have very little importance during accidents. Such systems are very innovative being based on the coupling of an accelerator with a subcritical system by means of a target system, where the neutronic source needed to maintain the neutron reaction chain is produced by spallation reactions. To this end the PDS-XADS (Preliminary Design Studies on an experimental Accelerator Driven System) project was funded by the European Community in the 5th Framework Program in order both to demonstrate the feasibility of the coupling between an accelerator and a sub-critical core loaded with standard MOX fuel and to investigate the transmutation capability in order to achieve values suitable for an Industrial Scale Transmuter. This paper summarizes and compares the results of neutronic calculations aimed at evaluating the transmutation capability of cores cooled by Lead-Bismuth Eutectic alloy and loaded with assemblies based on (Pu, Am, Cm) oxide dispersed in a molybdenum metal (CERMET) or magnesia (CERCER) matrices. It also describes the constraints considered in the design of such cores and describes the thermo-mechanical behaviour of these innovative fuels along the cycle. 2. DESCRIPTION OF THE WORK: The U-free composite fuels (CERMET and CERCER) were selected for this study, being considered at European level

About the first experiment on investigation of 129I, 237Np, 238Pu and 239Pu transmutation at the nuclotron 2.52 GeV deuteron beam in neutron field generated in U/Pb-assembly 'Energy plus transmutation'

International Nuclear Information System (INIS)

Krivopustov, M.I.; Pavliouk, A.V.; Malakhov, A.I.

2008-01-01

Preliminary results of the first experiment with energy 2.52 GeV at the electronuclear setup which consists of Pb-target (diameter 8.4 cm, length 45.6 cm) and nat U-blanket (206.4 kg), transmutation samples of 129 I, 237 Np, 238 Pu and 239 Pu (radioecological aspect) are described. Hermetically sealed samples in notable amounts are gathered in atomic reactors and setups of industries which use nuclear materials and nuclear technologies were irradiated in the field of neutrons produced in the Pb-target and propagated in the nat U-blanket. Estimates of transmutations were obtained as a result of measurements of gamma activities of the samples. The information about the space and energy distribution of neutrons in the volume of the lead target and the uranium blanket was obtained with the help of sets of activation threshold detectors (Al, Co, Y, I, Au, Bi and others), solid-state nuclear track detectors, 3 He neutron detectors and nuclear emulsion. Comparison of the experimental data with the results of simulation with the MCNPX program was performed

The transmutation of americium: the Ecrix experiments in Phenix; Transmutation de l'americium: les experiences ecrix dans Phenix

Energy Technology Data Exchange (ETDEWEB)

Garnier, J.C.; Schmidt, N. [CEA Cadarache, Dept. d' Etudes des Combustibles (DEC/SESC), 13 - Saint-Paul-lez-Durance (France); Croixmarie, Y.; Ottaviani, J.P. [CEA Cadarache, Dept. d' Etudes des Combustibles (DEC/SPUA), 13 - Saint-Paul-lez-Durance (France); Varaine, F.; Saint Jean, C. de [CEA Cadarache, Dept. d' Etudes des Reacteurs (DER/SPRC), 13 - Saint-Paul-lez-Durance (France)

1999-07-01

The first americium transmutation experiment in a specific target in PHENIX will occur with the ECRIX-B and ECRIX-H experiments. Beside material testing, the objective is also to represent a concept of transmutation whose specificity is to enhance the kinetics of transmutation by using a moderated spectrum. The moderator materials will be {sup 11}B{sub 4}C and CaH{sub 2} for ECRIX-B and ECRIXH respectively, the irradiation conditions have been predicted for both the neutronics and thermal. The targets (MgO-AmO{sub X} pellets) are manufactured in the ATALANTE laboratory and the design is performed according to the PHENIX operating conditions. (authors)

Tokamak transmutation of (nuclear) waste (TTW): Parametric studies

International Nuclear Information System (INIS)

Cheng, E.T.; Krakowski, R.A.; Peng, Y.K.M.

1994-01-01

Radioactive waste generated as part of the commercial-power and defense nuclear programs can be either stored or transmuted. The latter treatment requires a capital-intensive neutron source and is reserved for particularly hazardous and long-lived actinide and fission-product waste. A comparative description of fusion-based transmutation is made on the basis of rudimentary estimates of ergonic performance and transmutation capacities versus inventories for both ultra-low-aspect-ratio (spherical torus, ST) and conversional (aspect-ratio) tokamak fusion-power-core drivers. The parametric systems studies reported herein provides a preamble to more-detailed, cost-based systems analyses

Nuclear waste transmutation

International Nuclear Information System (INIS)

Leray, S.

1995-01-01

Accelerators can play a role in the disposal of long-lived radioactive waste: an alternative to the storage in deep underground repositories might transmuting long-lived elements into stable or short-lived ones in subcritical systems driven by spallation neutrons. These neutrons would be produced by a high intensity, intermediate energy proton accelerator irradiating a heavy target. Similar systems have also been proposed to produce energy with a minimized waste inventory. Since a good knowledge of the spallation process is essential for designing and optimizing the target-blanket assembly, new programmes aimed at studying spallation reactions are in progress. (author). 6 figs

Analysis of minor actinides transmutation for a Molten Salt Fast Reactor

International Nuclear Information System (INIS)

Yu, Chenggang; Li, Xiaoxiao; Cai, Xiangzhou; Zou, Chunyan; Ma, Yuwen; Han, Jianlong; Chen, Jingen

2015-01-01

Highlights: • The transmutation of MA in a 500 MWth MSFR is analyzed. • A larger MA loading can enhance the MA transmutation and deepen the burnup. • The MA transmutation efficiency can reach 95%. • The FTC can satisfy the safe operating requirement during the entire operating. - Abstract: As one of the six candidate reactors chosen by the Generation IV International Forum (GIF), Molten Salt Fast Reactor (MSFR) has many outstanding advantages and features for advanced nuclear fuel utilization. Effective transmutation of minor actinides (MA) could be attained in this kind of fast reactor, which is of importance in the future closed nuclear fuel cycle scenario. In this work, we attempt to study the MA transmutation capability in a MSFR with power of 500 MWth by analyzing the neutronics characteristics for different MA loadings. The calculated results show that MA loading plays an important role in the reactivity evolution of the MSFR. A larger MA loading is favorable to improving the MA transmutation performance and simultaneously to reducing the fissile consumption. When MA = 18.17 mol%, the transmutation fraction can achieve to about 95% on iso-breeding. We also find that although the fuel temperature coefficient (FTC) decreases with the increasing MA loading, it is still negative enough to keep the safety of the MSFR during the whole operation time. The MA contribution to the effective delayed neutron fraction (EDNF) and the intensity of spontaneous fission neutron (ISFN) are also analyzed. Also MA loading can affect the EDNF during the operation and the ISFN of the MSFR is dominated by 244 Cm. Finally, we analyze the effect of the core power on MA transmutation capability. The result shows that for all the operating powers the depletion ratio of MA to HN increases with time and reaches a maximum value. And additional MA should be fed into the fuel salt before the MA depletion ratio reaches the peak value to improve its transmutation capability. The net

A theoretical model for the production of Ac-225 for cancer therapy by neutron capture transmutation of Ra-226.

Science.gov (United States)

Melville, G; Melville, P

2013-02-01

Radium needles that were once implanted into tumours as a cancer treatment are now obsolete and constitute a radioactive waste problem, as their half-life is 1600 years. We are investigating the reduction of radium by transmutation by bombarding Ra-226 with high-energy neutrons from a neutron source to produce Ra-225 and hence Ac-225, which can be used as a generator to produce Bi-213 for use in 'Targeted Alpha Therapy' for cancer. This paper examines the possibility of producing Ac-225 by neutron capture using a theoretical model in which neutron energy is convoluted with the corresponding neutron cross sections of Ra-226. The total integrated yield can then be obtained. This study shows that an intense beam of high-energy neutrons could initiate neutron capture on Ra-226 to produce Ra-225 and hence practical amounts of Ac-225 and a useful reduction of Ra-226. Copyright © 2012 Elsevier Ltd. All rights reserved.

Radiotoxicity of Actinides During Transmutation in Final Stage of Atomic Power

International Nuclear Information System (INIS)

Gerasimov, Aleksander S.; Bergelson, Boris R.; Myrtsymova, Lidia A.; Tikhomirov, Georgy V.

2002-01-01

Characteristics of a transmutation mode in final stage of atomic power are analyzed. In this stage, transmutation of actinides accumulated in transmutation reactors is performed without feed by actinides from other reactors. The radiotoxicity during first 20 years of transmutation is caused mainly by 244 Cm. During following period of time, 252 Cf is main nuclide. Contribution of 246 Cm and 250 Cf is 5-7 times less than that of 252 Cf. During 50 years of a transmutation, the total radiotoxicity falls by 50 times. Long-lived radiotoxicity decreases slowly. During the period between T=50 years and T=100 years, long-lived radiotoxicity falls by 3.7 times. For each following 50 years after this period, long-lived radiotoxicity falls by 3.2 times. These results corresponding to neutron flux density 10 14 neutr/(cm 2 s) in transmutation reactor demonstrate that the final stage of a transmutation should be performed with use of high flux transmutation facilities which provide shorter time of transmutation. (authors)

Impact of Blanket Configuration on the Design of a Fusion-Driven Transmutation Reactor

Directory of Open Access Journals (Sweden)

Bong Guen Hong

2018-02-01

Full Text Available A configuration of a fusion-driven transmutation reactor with a low aspect ratio tokamak-type neutron source was determined in a self-consistent manner by using coupled analysis of tokamak systems and neutron transport. We investigated the impact of blanket configuration on the characteristics of a fusion-driven transmutation reactor. It was shown that by merging the TRU burning blanket and tritium breeding blanket, which uses PbLi as the tritium breeding material and as coolant, effective transmutation is possible. The TRU transmutation capability can be improved with a reduced blanket thickness, and fast fluence at the first wall can be reduced.  Article History: Received: July 10th 2017; Received: Dec 17th 2017; Accepted: February 2nd 2018; Available online How to Cite This Article: Hong, B.G. (2018 Impact of Blanket Configuration on the Design of a Fusion-Driven Transmutation Reactor. International Journal of Renewable Energy Development, 7(1, 65-70. https://doi.org/10.14710/ijred.7.1.65-70

Shifts in Selective Pressures on Snake Phototransduction Genes Associated with Photoreceptor Transmutation and Dim-Light Ancestry.

Science.gov (United States)

Schott, Ryan K; Van Nynatten, Alexander; Card, Daren C; Castoe, Todd A; S W Chang, Belinda

2018-06-01

The visual systems of snakes are heavily modified relative to other squamates, a condition often thought to reflect their fossorial origins. Further modifications are seen in caenophidian snakes, where evolutionary transitions between rod and cone photoreceptors, termed photoreceptor transmutations, have occurred in many lineages. Little previous work, however, has focused on the molecular evolutionary underpinnings of these morphological changes. To address this, we sequenced seven snake eye transcriptomes and utilized new whole-genome and targeted capture sequencing data. We used these data to analyze gene loss and shifts in selection pressures in phototransduction genes that may be associated with snake evolutionary origins and photoreceptor transmutation. We identified the surprising loss of rhodopsin kinase (GRK1), despite a low degree of gene loss overall and a lack of relaxed selection early during snake evolution. These results provide some of the first evolutionary genomic corroboration for a dim-light ancestor that lacks strong fossorial adaptations. Our results also indicate that snakes with photoreceptor transmutation experienced significantly different selection pressures from other reptiles. Significant positive selection was found primarily in cone-specific genes, but not rod-specific genes, contrary to our expectations. These results reveal potential molecular adaptations associated with photoreceptor transmutation and also highlight unappreciated functional differences between rod- and cone-specific phototransduction proteins. This intriguing example of snake visual system evolution illustrates how the underlying molecular components of a complex system can be reshaped in response to changing selection pressures.

Study of an optimal configuration of a transmutation reactor based on a low-aspect-ratio tokamak

Energy Technology Data Exchange (ETDEWEB)

Hong, Bong Guen, E-mail: bghong@jbnu.ac.kr [Department of Quantum System Engineering, Chonbuk National University, 567 Baekje-daero, Jeonju, Jeonbuk 54896 (Korea, Republic of); Kim, Hoseok [Department of Applied Plasma Engineering, Chonbuk National University, 567 Baekje-daero, Jeonju, Jeonbuk 54896 (Korea, Republic of)

2016-11-15

Highlights: • Optimum configuration of a transmutation reactor based on a low aspect ratio tokamak was found. • Inboard and outboard radial build are determined by plasma physics, engineering and neutronics constraints. • Radial build and equilibrium fuel cycle play a major role in determining the transmutation characteristics. - Abstract: We determine the optimal configuration of a transmutation reactor based on a low-aspect-ratio tokamak. For self-consistent determination of the radial build of the reactor components, we couple a tokamak systems analysis with a radiation transport calculation. The inboard radial build of the reactor components is obtained from plasma physics and engineering constraints, while outboard radial builds are mainly determined by constraints on neutron multiplication, the tritium-breeding ratio, and the power density. We show that the breeding blanket model has an effect on the radial build of a transmutation blanket. A burn cycle has to be determined to keep the fast neutron fluence plasma-facing material below its radiation damage limit. We show that the radial build of the transmutation reactor components and the equilibrium fuel cycle play a major role in determining the transmutation characteristics.

Application of gaseous core reactors for transmutation of nuclear waste

Science.gov (United States)

Schnitzler, B. G.; Paternoster, R. R.; Schneider, R. T.

1976-01-01

An acceptable management scheme for high-level radioactive waste is vital to the nuclear industry. The hazard potential of the trans-uranic actinides and of key fission products is high due to their nuclear activity and/or chemical toxicity. Of particular concern are the very long-lived nuclides whose hazard potential remains high for hundreds of thousands of years. Neutron induced transmutation offers a promising technique for the treatment of problem wastes. Transmutation is unique as a waste management scheme in that it offers the potential for "destruction" of the hazardous nuclides by conversion to non-hazardous or more manageable nuclides. The transmutation potential of a thermal spectrum uranium hexafluoride fueled cavity reactor was examined. Initial studies focused on a heavy water moderated cavity reactor fueled with 5% enriched U-235-F6 and operating with an average thermal flux of 6 times 10 to the 14th power neutrons/sq cm-sec. The isotopes considered for transmutation were I-129, Am-241, Am-242m, Am-243, Cm-243, Cm-244, Cm-245, and Cm-246.

Comparative Study of the Reactor Burner Efficiency for Transmutation of Minor Actinides

Energy Technology Data Exchange (ETDEWEB)

Gulevich, A.; Zemskov, E. [Institute of Physics and Power Engineering, Bondarenko sq. 1, Obninsk, Kaluga region, 249020 (Russian Federation); Degtyarev, A.; Kalugin, A.; Ponomarev, L. [Russian Research Center ' Kurchatov Institute' , Kurchatov sq. 1, Moscow, 123182 (Russian Federation); Konev, V.; Seliverstov, V. [Institute of Theoretical and Experimental Physics, ul. B. Cheremushinskaya 25, Moscow, 117259 (Russian Federation)

2009-06-15

Transmutation of minor actinides (MA) in the closed nuclear fuel cycle (NFC) is a one of the most important problem for future nuclear energetic. There are several approaches for MA transmutation but there are no common criteria for the comparison of their efficiency. In paper [1] we turned out the attention to the importance of taking into account the duration of the closed NFC in addition to a usual criterion of the neutron economy. In accordance with these criteria the transmutation efficiency are compared of two fast reactors (sodium and lead cooled) and three types of ADS-burners: LBE-cooled reactors (fast neutron spectrum), molten-salt reactor (intermediate spectrum) and heavy water reactor (thermal spectrum). It is shown that the time of transmutation of loaded MA in the closed nuclear fuel cycle is more than 50 years. References: A. Gulevich, A. Kalugin, L. Ponomarev, V. Seliverstov, M. Seregin, 'Comparative Study of ADS for Minor Actinides Transmutation', Progress in Nuclear Energy, 50, March-August, p. 358, 2008. (authors)

Grouping in partitioning of HLW for burning and/or transmutation with nuclear reactors

International Nuclear Information System (INIS)

Kitamoto, Asashi; Mulyanto.

1995-01-01

A basic concept on partitioning and transmutation treatment by neutron reaction was developed in order to improve the waste management and the disposal scenario of high level waste (HLW). The grouping in partitioning was important factor and closely linked with the characteristics of B/T (burning and/or transmutation) treatment. The selecting and grouping concept in partitioning of HLW was proposed herein, such as Group MA1 (Np, Am, and unrecovered U and Pu), Group MA2 (Cm, Cf etc.), Group A (Tc and I), Group B (Cs and Sr) and Group R (the partitioned remain of HLW), judging from the three criteria for B/T treatment proposed in this study, which is related to (1) the value of hazard index for long-term tendency based on ALI, (2) the relative dose factor related to the mobility or retardation in ground water penetrated through geologic layer, and (3) burning and/or transmutation characteristics for recycle B/T treatment and the decay acceleration ratio by neutron reaction. Group MA1 and Group A could be burned effectively by thermal B/T reactor. Group MA2 could be burned effectively by fast B/T reactor. Transmutation of Group B by neutron reaction is difficult, therefore the development of radiation application of Group B (Cs and Sr) in industrial scale may be an interesting option in the future. Group R, i.e. the partitioned remains of HLW, and also a part of Group B should be immobilized and solidified by the glass matrix. HI ALI , the hazard index based on ALI, due to radiotoxicity of Group R can be lower than HI ALI due to standard mill tailing (smt) or uranium ore after about 300 years. (author)

The status of nuclear data for transmutation calculations

International Nuclear Information System (INIS)

Wilson, W.B.; England, T.R.; MacFarlane, R.E.; Muir, D.W.; Young, P.G.

1995-01-01

At this point, the accurate description of transmutation products in a radiation environment is more a nuclear data problem than a code development effort. We have used versions of the CINDER code for over three decades to describe the transmutation of nuclear reactor fuels in radiation environments. The need for the accurate description of reactor neutron-absorption, decay-power, and decay-spectra properties have driven many AEC, ERDA, and DOE supported nuclear data development efforts in this period. The level of cross-section, decay, and fission-yield data has evolved from rudimentary to a comprehensive ENDF/B-VI library permitting great precision in reactor calculations. The precision of the data supporting reactor simulations provides a sturdy foundation for the data base required for the wide range of transmutation problems currently studied. However, such reactor problems are typically limited to neutron energies below 10 MeV or so; reaction and decay data are required for actinides of, say, 90 ≤ Z ≤ 96 neutron-rich fission products of 22 ≤ Z ≤ 72. The expansion into reactor structural materials and fusion systems extends these ranges in energy and Z somewhat. The library of nuclear data, constantly growing in breadth and quality with international cooperation, is now described in the following table

Measurements of the neutron capture cross sections and incineration potentials of minor-actinides in high thermal neutron fluxes: Impact on the transmutation of nuclear wastes

International Nuclear Information System (INIS)

Bringer, O.

2007-10-01

This thesis comes within the framework of minor-actinide nuclear transmutation studies. First of all, we have evaluated the impact of minor actinide nuclear data uncertainties within the cases of 241 Am and 237 Np incineration in three different reactor spectra: EFR (fast), GT-MHR (epithermal) and HI-HWR (thermal). The nuclear parameters which give the highest uncertainties were thus highlighted. As a result of fact, we have tried to reduce data uncertainties, in the thermal energy region, for one part of them through experimental campaigns in the moderated high intensity neutron fluxes of ILL reactor (Grenoble). These measurements were focused onto the incineration and transmutation of the americium-241, the curium-244 and the californium-249 isotopes. Finally, the values of 12 different cross sections and the 241 Am isomeric branching ratio were precisely measured at thermal energy point. (author)

Determination of spatial and energy distributions of neutrons in experiments on transmutation of radioactive waste using relativistic protons

International Nuclear Information System (INIS)

Zhuk, I.V.; Lomonosova, E.M.; Boulyga, S.F.; Kievitskaia, A.I.; Rakhno, I.L.; Chigrinov, S.E.; Bradnova, V.; Krivopustov, M.I.; Kulakov, B.A.; Brandt, R.; Ochs, M.; Wan, J.-S.

1999-01-01

The experiments on transmutation of 129 I and 237 Np using uranium-lead targets surrounded by a paraffin moderator were performed at the Joint Institute for Nuclear Research (JINR, Russia). The targets were irradiated by 1.5 GeV and 7.4 GeV protons at the Synchrophasotron of JINR. In the frame of present work spatial and energy distributions of neutrons on the surface of the paraffin moderator were measured using SSNTD technique. It is shown that measured values of spectral indices do not depend on the energy of incident protons but depend on the target composition. The presence of the uranium insertion softens neutron spectra

Determination of spatial and energy distributions of neutrons in experiments on transmutation of radioactive waste using relativistic protons

Energy Technology Data Exchange (ETDEWEB)

Zhuk, I.V.; Lomonosova, E.M.; Boulyga, S.F.; Kievitskaia, A.I.; Rakhno, I.L.; Chigrinov, S.E.; Bradnova, V.; Krivopustov, M.I.; Kulakov, B.A.; Brandt, R.; Ochs, M.; Wan, J.-S

1999-06-01

The experiments on transmutation of {sup 129}I and {sup 237}Np using uranium-lead targets surrounded by a paraffin moderator were performed at the Joint Institute for Nuclear Research (JINR, Russia). The targets were irradiated by 1.5 GeV and 7.4 GeV protons at the Synchrophasotron of JINR. In the frame of present work spatial and energy distributions of neutrons on the surface of the paraffin moderator were measured using SSNTD technique. It is shown that measured values of spectral indices do not depend on the energy of incident protons but depend on the target composition. The presence of the uranium insertion softens neutron spectra.

Analysis on Radioactive Waste Transmutation in Light Water cooled Hyb-WT

International Nuclear Information System (INIS)

Hong, Seonghee; Kim, Myung Hyun

2014-01-01

A feasibility of realization is much higher in FFHR compared with pure fusion. A combination of plasma fusion source for neutrons with a subcritical reactor at the blanket side has much higher capability in transmutation of waste as well as reactor safety compared with fission reactor options. Fusion-Fission Hybrid Reactor (FFHR) uses various coolants depending on the purpose. It is important that coolant being used should be suitable to reactor purpose, because reactor performance and the design constraints may change depending on the coolant. There are basically two major groups of coolants for FFHR. One group of coolant does not contain Li. They are Na, Pb-Bi, H 2 O and D 2 O. The other group contains Li for tritium breeding. They are Li, LiPb, LiSN, FLIBE and FLiNaBe. Currently, the issue in FFHR is its implication for radioactive waste transmutation (FFHR for WT). Because radioactive wastes of spent nuclear fuel (SNF) are transmuted using fusion neutron source. Therefore a suitable coolant should be used for effective waste transmutation. . In FFHR for WT, LiPb coolant is being used mainly because of tritium production in Li and high neutron economic through reaction in Pb. However different coolants use such as Na, Pb-Bi are used in fast reactors and accelerator driven systems (ADS) having same purpose. In this study, radioactive waste transmutation performance of various coolants mentioned above will be compared and analyzed. Through this study, the coolants are judged primarily for their support to waste transmutation disregarding their limitation to reactor design and tritium breeding capability. First, performance of the light water coolant regarding radioactive waste transmutation was analyzed among various coolants mentioned above. In this paper, performance of radioactive waste transmutation can be known depending on different volume fractions (54.53, 60.27, 97.94vol.%) of the light water. Light water dose required fusion power lower than LiPb due to

Ma and LLFP transmutation in MTPs and ADSs: the typical SCK.CEN case of transmutations in BR2 and Myrrha. Position with respect to the global needs

International Nuclear Information System (INIS)

Raedt, Ch. de; Verboomen, B.; Aoust, Th.; Malambu, E.; Beeckmans de West-Meerbeeck, A.; Kupschus, P.; Benoit, Ph.; Ait Abderrahim, H.; Baetsle, L.H.

2001-01-01

The proposed paper indicates the performances, in the domain of the transmutation of MAs and LLFPs, of the high flux materials testing reactor BR2 located at SCK-CEN, and compares them with those of the multipurpose ADS MYRRHA, the pre-design of which is at the present time being finalized at SCK-CEN. With thermal neutron fluxes reaching 9.10 14 n/cm 2 s in thermal positions and 4.10 14 n/cm 2 s in the reactor core and, in the latter position, a fast flux (E>0.1 MeV) of 7.10 14 n/cm 2 s, BR2 has a transmutation throughput of the order of 1.5 kg Np+Am per 200 EFPD. This capacity can be used for investigating at the technological scale the transmutation of MAs and LLFPs in a thermal neutron spectrum with a high contribution of epithermal and fast neutrons. The metallurgical behaviour of the targets can hence be studied. In MYRRHA, higher fast fluxes are expected to be attained in irradiation positions near the spallation source, viz fast fluxes (E>0.75 MeV) up to 10. 15 n/cm 2 s. One of the purposes of MYRRHA is therefore its utilisation for the investigation of actinide transmutation feasibility with ADSs. (author)

Design Concept of the Thermal Flux Island in MYRRHA for LLFP Transmutation. Present Status

International Nuclear Information System (INIS)

Aoust, Th.; De Raedt, Ch.; Malambu, E.; Ait Abderrahim, H.

2002-01-01

MYRRHA is an ADS aimed at providing protons and neutrons for various R and D applications. It consists of a proton accelerator coupled to a sub-critical fast core. While the fast neutron spectrum, obtaining in the MYRRHA core, allows the transmutation of minor actinides (MAs), the transmutation of long lived fission products (LLFPs) in MYRRHA requires the utilisation of a thermal spectrum in order to take profit of the fact that the capture cross-sections of the LLFPs are much larger in the thermal-energy domain than in the high-energy domain. A high thermal flux island inside MYRRHA is therefore being developed, consisting of an irradiation device for LLFPs (or other irradiation target material needing a thermal neutron spectrum), surrounded by assemblies filled with a lattice of ZrH 2 moderator pins, cooled by the same coolant (Pb-Bi) as the MYRRHA fuel assemblies. Thermal neutron absorbers at the periphery of the neutron island are used to minimise the influence of the thermal flux on the fast core. The study of the performances of MYRRHA, including the transmutation of the LLFPs in such a thermal island, is carried out with the aid of the code MCNPX. The transmutation performances of LLFPs are assessed by coupling the code MCNPX to an evolution calculation. The LLFPs studied are Tc-99 and I-129. (authors)

Feasibility of waste transmutation using accelerator-driven IRIS subcritical system

International Nuclear Information System (INIS)

Petroviae, B.; Carelli, M.; Paramonov, D.

2001-01-01

Waste transmutation is considered for reducing radio-toxicity of nuclear waste generated in power reactors. Accelerator driven subcritical systems (ADS) offer certain advantages over the use of nuclear reactors. Transmutation of fission products (e.g. 99 Tc) generally requires thermal neutron spectrum, while for actinides fast spectrum provides better performance. Proposed solutions to this problem include a multi-strata approach as well as a multi-zone (thermal/fast-spectrum) single systems. In this paper we examine the feasibility of employing a dual-spectrum two-zone accelerator-driven IRIS subcritical for waste transmutation. (author)

Role of accelerators in the Czech national transmuter project

International Nuclear Information System (INIS)

Bem, P.; Kugler, A.

1999-01-01

The problem of spent nuclear fuel from the so far operated PWRs has become a crucial issue in the Czech Republic. The first attempts to solve this problem by a final deposit of spent fuel into a suitable geological formation have been shown not to be fully acceptable. Therefore, the revival of nuclear transmutation technology application for nuclear incineration of nuclear waste and spent fuel in particular was welcomed. A realistic national project started to be developed in 1996. The four major nuclear research institutions of the country formed a consortium focused on an adoption of the world-wide experience and a development of a national project of a transmutation technology (experimental transmuter LA-0) or an efficient participation in the international effort in that field. Because the LA-0 transmuter concept of subcritical reactor with liquid fuel based on molten fluorides driven by an external neutron source has been adopted, the R and D effort has been focused on three regions. The first is devoted to the problem of a suitable neutron source, the second to a pre-conceptual design of a blanket for burning of actinides contained in spent fuel from PWRs. The third region is devoted to the utilisation of the experience from a specific field of dry (fluorine) reprocessing of spent fuel and a preparation of liquid fuel in the form of molten fluorides for the transmuter LA-0. (R.P.)

Development of transmutation technologies of radioactive waste by actinoid hydride

International Nuclear Information System (INIS)

Konashi, Kenji; Matsui, Hideki; Yamawaki, Michio

2001-01-01

Two waste treatment methods, geological disposal and transmutation, have been studied. The transmutation method changes long-lived radioactive nuclides to short-lived one or stabilizes them by nuclear transformation. The transmutation by actinoid hydride is exactly alike that transformation method from actinoid disposal waste to Pu fuel. For this object, OMEGA project is processing now. The transmutation is difficult by two causes such as large amount of long-lived radioactive nuclides and not enough development of control technologies of nuclear reaction except atomic reactor. The transmutation using actinoid hydride has merits that the amount of actinoid charged in the target increases and the effect of thermal neutrons on fuel decreases depending on homogeneous transmutation velocity in the target. Development of stable actinoid hydride under the conditions of reactor temperature and irradiation environment is important. The experimental results of U-ZrH 1.6 are shown in this paper. The irradiation experiment using Th hydride has been proceeding. (S.Y.)

On fusion driven systems (FDS) for transmutation

Energy Technology Data Exchange (ETDEWEB)

Aagren, O (Uppsala Univ., Aangstroem laboratory, div. of electricity, Uppsala (Sweden)); Moiseenko, V.E. (Inst. of Plasma Physics, National Science Center, Kharkov Inst. of Physics and Technology, Kharkov (Ukraine)); Noack, K. (Forschungszentrum Dresden-Rossendorf (Germany))

2008-10-15

This report gives a brief description of ongoing activities on fusion driven systems (FDS) for transmutation of the long-lived radioactive isotopes in the spent nuclear waste from fission reactors. Driven subcritical systems appears to be the only option for efficient minor actinide burning. Driven systems offer a possibility to increase reactor safety margins. A comparatively simple fusion device could be sufficient for a fusion-fission machine, and transmutation may become the first industrial application of fusion. Some alternative schemes to create strong fusion neutron fluxes are presented

On fusion driven systems (FDS) for transmutation

International Nuclear Information System (INIS)

Aagren, O; Moiseenko, V.E.; Noack, K.

2008-10-01

This report gives a brief description of ongoing activities on fusion driven systems (FDS) for transmutation of the long-lived radioactive isotopes in the spent nuclear waste from fission reactors. Driven subcritical systems appears to be the only option for efficient minor actinide burning. Driven systems offer a possibility to increase reactor safety margins. A comparatively simple fusion device could be sufficient for a fusion-fission machine, and transmutation may become the first industrial application of fusion. Some alternative schemes to create strong fusion neutron fluxes are presented

Transmutation of transuranium elements in a gas-cooled accelerator-driven system

International Nuclear Information System (INIS)

Biss, Klaus Hendrik

2014-01-01

The peaceful usage of nuclear energy by light and boiling water reactors is connected with a buildup of long-lived high-level radioactive waste. Compared to the direct disposal, partitioning and transmutation (P and T) is considered as an effective way to reduce this waste in its quantity by converting it into short-lived radio nuclides. By that the long term radiotoxicity is reduced compared to direct disposal. Subcritical systems, which are powered by spallation processes for free neutron production to maintain the nuclear chain reaction, allow a target-oriented transmutation. As a subcritical system a gas-cooled accelerator driven system (ADS) for transmutation of transuranic elements has been modeled in this thesis to evaluate the reduction of the radio toxicity by P and T. The simulation of neutron-physical processes is based on the Monte Carlo computer program MCNPX. The development of an equilibrium core made it possible to study the transmutation and operating behavior for several fuel variations in a magnesium oxide matrix and develop a simplified burnup method. Americium as part of the fuel has a stabilizing effect on the neutron multiplication due to its conversion into plutonium during the operation. Thorium was investigated as an alternative matrix for the fuel in order to replicate the stabilizing effect of americium by the conversion of thorium in 233 U. By that a consistent operating cycle in the later P and T-process is ensured. Calculation of the nuclide composition at the end of a P and T-process leads to an expansion of the mathematical description of the mass reduction (transmutation efficiency) by the material located in the reactor. The achieved transmutation efficiency with the investigated ADS is 98.8 %. The transmutation time was examined with different operating strategies regarding the number, size and thermal power of use of transmutation facilities to determine the effort for the P and T-process depending on efficiency. It turns out

Determination of spatial and energy distributions of neutrons in experiments on transmutation of radioactive waste using relativistic protons

CERN Document Server

Zhuk, I V; Boulyga, S F; Kievitskaia, A I; Rakhno, I L; Chigrinov, S E; Bradnova, V; Krivopustov, M I; Kulakov, B A; Brandt, R; Ochs, M; Wan, J S

1999-01-01

The experiments on transmutation of sup 1 sup 2 sup 9 I and sup 2 sup 3 sup 7 Np using uranium-lead targets surrounded by a paraffin moderator were performed at the Joint Institute for Nuclear Research (JINR, Russia). The targets were irradiated by 1.5 GeV and 7.4 GeV protons at the Synchrophasotron of JINR. In the frame of present work spatial and energy distributions of neutrons on the surface of the paraffin moderator were measured using SSNTD technique. It is shown that measured values of spectral indices do not depend on the energy of incident protons but depend on the target composition. The presence of the uranium insertion softens neutron spectra.

The transmutation of americium: the Ecrix experiments in Phenix

International Nuclear Information System (INIS)

Garnier, J.C.; Schmidt, N.; Croixmarie, Y.; Ottaviani, J.P.; Varaine, F.; Saint Jean, C. de

1999-01-01

The first americium transmutation experiment in a specific target in PHENIX will occur with the ECRIX-B and ECRIX-H experiments. Beside material testing, the objective is also to represent a concept of transmutation whose specificity is to enhance the kinetics of transmutation by using a moderated spectrum. The moderator materials will be 11 B 4 C and CaH 2 for ECRIX-B and ECRIXH respectively, the irradiation conditions have been predicted for both the neutronics and thermal. The targets (MgO-AmO X pellets) are manufactured in the ATALANTE laboratory and the design is performed according to the PHENIX operating conditions. (authors)

Status report on actinide and fission product transmutation studies

International Nuclear Information System (INIS)

1997-06-01

The management of radioactive waste is one of the key issues in today's political and public discussions on nuclear energy. One of the fields that looks into the future possibilities of nuclear technology is the neutronic transmutation of actinides and of some most important fission products. Studies on transmutation of actinides are carried out in various countries and at an international level. This status report which gives an up-to-date general overview of current and planned research on transmutation of actinides and fission products in non-OECD countries, has been prepared by a Technical Committee meeting organized by the IAEA in September 1995. 168 refs, 16 figs, 34 tabs

Study on MAs transmutation of accelerator-driven system sodium-cooled fast reactor loaded with metallic fuel

International Nuclear Information System (INIS)

Han Song; Yang Yongwei

2007-01-01

Through the analysis of the effect of heavy metal actinides on the effective multiplication constant (k eff ) of the core in accelerator-driven system (ADS) sodium-cooled fast reactor loaded with metallic fuel, we gave the method for determining fuel components. the characteristics of minor actinides (MAs) transmutation was analyzed in detail. 3D burn-up code COUPLE, which couples MCNP4c3 and ORIGEN2, was applied to the neutron simulation and burn up calculation. The results of optimized scheme shows that adjusting the proportion of 239 Pu and maintaining the value during the burn-up cycle is an efficient method of designing k eff and keeping stable during the burn-up cycle. Spallation neutrons lead to the neutron spectrum harder at inner core than that at outer core. It is in favor of improving MA's fission cross sections and the capture-to-fission ratio. The total MAs transmutation support ratio 8.3 achieves excellent transmutation effect. For higher flux at inner core leads to obvious differences on transmutation efficiency,only disposing MAs at inner core is in favor of decreasing the loading mass and improving MAs transmutation effect. (authors)

Impact of Transmutation Scenarios on Fuel Transportation

International Nuclear Information System (INIS)

Saturnin, A.; Duret, B.; Allou, A.; Jasserand, F.; Fillastre, E.; Giffard, F.X.; Chabert, C.; Caron-Charles, M.; Garzenne, C.; Laugier, F.

2015-01-01

Minor actinides transmutation scenarios have been studied in the frame of the French Sustainable Radioactive Waste Management Act of 28 June 2006. Transmutation scenarios supposed the introduction of a sodium-cooled fast reactor fleet using homogeneous or heterogeneous recycling modes for the minor actinides. Americium, neptunium and curium (MA) or americium alone (Am) can be transmuted together in a homogeneous way embedded in FR-MOX fuel or incorporated in MA or Am-Bearing radial Blankets (MABB or AmBB). MA transmutation in Accelerator Driven System has also been studied while plutonium is being recycled in SFR. Assessments and comparisons of these advanced cycles have been performed considering technical and economic criteria. Transportation needs for fresh and used transmutation fuels is one of these criteria. Transmutation fuels have specific characteristics in terms of thermal load and neutron emissions. Thermal, radiation and criticality constraints have been taken into account in this study to suggest cask concepts for routine conditions of transport, to estimate the number of assemblies to be transported in a cask and the number of annual transports. Comparison with the no transmutation option, i.e. management of uranium and plutonium in SFRs, is also presented. Regarding these matters, no high difficulties appear for assemblies with limited content of Am (homogeneous or heterogeneous recycling modes). When fuels contain curium, technical transport uncertainties increase because of the important heat release requiring dividing fresh fuels and technological innovations development (MABB and ADS). (authors)

Estimation of the outlooks for large-scale transmutation of fission-produced iodine

CERN Document Server

Galkin, B Y; Kolyadin, A B; Kocherov, N P; Lyubtsev, R I; Hosov, A A; Rimskij-Korsakov, A A

2002-01-01

To obtain data necessary for estimating sup 1 sup 2 sup 9 I transmutation efficiency in nuclear reactors the effective neutron capture cross section on sup 1 sup 2 sup 9 I isotope in neutral spectrum of the WWR-M reactor was determined. The calculated value of sup 1 sup 2 sup 9 I capture cross section, averaged by neutron spectrum in beryllium reflector of the WWR-M reactor, made up 17.8+-3.2 barn. On the basis of experimental data and estimations it was shown that in neutron flux 10 sup 1 sup 4 1/(cm sup 2 s) transmutation of iodine -129 loaded in the course of one year can amount to approximately 25%

A new concept for accelerator driven transmutation of nuclear wastes

International Nuclear Information System (INIS)

Arthur, E.D.

1991-01-01

A new concept for an accelerator-driven transmutation system is described. The central feature of the concept is generation of intense fluxes of thermal neutrons. In the system all long-lived radionuclides comprising high-level nuclear waste can be transmuted efficiently. Transmutation takes place in a unique, low material inventory environment. Presently two principal areas are being investigated for application of the concept. The first is associated with cleanup of defense high-level waste at DOE sites such as Hanford. The second, longer term area involves production of electric power using a coupled accelerator-multiplying blanket system. This system would utilize natural thorium or uranium and would transmute long-lived components of high-level waste concurrently during operation. 5 refs., 5 figs

Transmutation of 129I and 237Np using spallation neutrons produced by 1.5, 3.7 and 7.4 GeV protons

International Nuclear Information System (INIS)

Wan, J.-S.; Schmidt, T.Th.; Langrock, E.-J.; Vater, P.; Brandt, R.; Adam, J.; Bradnova, V.; Bamblevski, V.P.; Gelovani, L.; Gridnev, T.D.; Kalinnikov, V.G.; Krivopustov, M.I.; Kulakov, B.A.; Sosnin, A.N.; Perelygin, V.P.; Pronskikh, V.S.; Stegailov, V.I.; Tsoupko-Sitnikov, V.M.; Modolo, G.; Odoj, R.; Phlippen, P.-W.; Zamani-Valassiadou, M.; Adloff, J.C.; Debeauvais, M.; Hashemi-Nezhad, S.R.; Guo, S.-L.; Li, L.; Wang, Y.-L.; Dwivedi, K.K.; Zhuk, I.V.; Boulyga, S.F.; Lomonossova, E.M.; Kievitskaja, A.F.; Rakhno, I.L.; Chigrinov, S.E.; Wilson, W.B.

2001-01-01

Small samples of 129 I and 237 Np, two long-lived radwaste nuclides, were exposed to spallation neutron fluences from relatively small metal targets of lead and uranium, that were surrounded with a 6 cm thick paraffin moderator, and irradiated with 1.5, 3.7 and 7.4 GeV protons. The (n,γ) transmutation rates were determined for these nuclides. Conventional radiochemical La- and U-sensors and a variety of solid-state nuclear track detectors were irradiated simultaneously with secondary neutrons. Compared with results from calculations with well-known cascade codes (LAHET from Los Alamos and DCM/CEM from Dubna), the observed secondary neutron fluences are larger

Transmutation of 129I and 237Np using spallation neutrons produced by 1.5, 3.7 and 7.4 GeV protons

Science.gov (United States)

Wan, J.-S.; Schmidt, Th.; Langrock, E.-J.; Vater, P.; Brandt, R.; Adam, J.; Bradnova, V.; Bamblevski, V. P.; Gelovani, L.; Gridnev, T. D.; Kalinnikov, V. G.; Krivopustov, M. I.; Kulakov, B. A.; Sosnin, A. N.; Perelygin, V. P.; Pronskikh, V. S.; Stegailov, V. I.; Tsoupko-Sitnikov, V. M.; Modolo, G.; Odoj, R.; Phlippen, P.-W.; Zamani-Valassiadou, M.; Adloff, J. C.; Debeauvais, M.; Hashemi-Nezhad, S. R.; Guo, S.-L.; Li, L.; Wang, Y.-L.; Dwivedi, K. K.; Zhuk, I. V.; Boulyga, S. F.; Lomonossova, E. M.; Kievitskaja, A. F.; Rakhno, I. L.; Chigrinov, S. E.; Wilson, W. B.

2001-05-01

Small samples of 129I and 237Np, two long-lived radwaste nuclides, were exposed to spallation neutron fluences from relatively small metal targets of lead and uranium, that were surrounded with a 6 cm thick paraffin moderator, and irradiated with 1.5, 3.7 and 7.4 GeV protons. The (n,γ) transmutation rates were determined for these nuclides. Conventional radiochemical La- and U-sensors and a variety of solid-state nuclear track detectors were irradiated simultaneously with secondary neutrons. Compared with results from calculations with well-known cascade codes (LAHET from Los Alamos and DCM/CEM from Dubna), the observed secondary neutron fluences are larger.

Electron paramagnetic resonance of isolated Assub(Ga)+ antisite defect in neutron-transmutation doped semi-insulating GaAs

International Nuclear Information System (INIS)

Manasreh, M.O.; McDonald, P.F.; Kivlighn, S.A.; Minton, J.T.; Covington, B.C.

1988-01-01

The isolated Assub(Ga) antisite defect produced by the neutron-transmutation doping in semi-insulating GaAs was studied using the electron paramagnetic resonance technique. The results show that the optically induced quenching of the isolated Assub(Ga) + antisite defect is quite different from that of the EL2 center. Illumination with white light seems to always reduce the electron paramagnetic resonance spectrum suggesting that depopulation of the EL2 center does not introduce a noticeable change in the Assub(Ga) + antisite concentration. (author)

A code system for ADS transmutation studies

International Nuclear Information System (INIS)

Brolly, A.; Vertes, P.

2001-01-01

An accelerator driven reactor physical system can be divided into two different subsystems. One is the neutron source the other is the subcritical reactor. Similarly, the modelling of such system is also split into two parts. The first step is the determination of the spatial distribution and angle-energy spectrum of neutron source in the target region; the second one is the calculation of neutron flux which is responsible for the transmutation process in the subcritical system. Accelerators can make neutrons from high energy protons by spallation or photoneutrons from accelerated electrons by Bremsstrahlung (e-n converter). The Monte Carlo approach is the only way of modelling such processes and it might be extended to the whole subcritical system as well. However, a subcritical reactor may be large, it may contain thermal regions and the lifetime of neutrons may be long. Therefore a comprehensive Monte Carlo modelling of such system is a very time consuming computational process. It is unprofitable as well when applied to system optimization that requires a comparative study of large number of system variants. An appropriate method of deterministic transport calculation may adequately satisfy these requirements. Thus, we have built up a coupled calculational model for ADS to be used for transmutation of nuclear waste which we refer further as M-c-T system. Flow chart is shown in Figure. (author)

Homogeneous Minor Actinide Transmutation in SFR: Neutronic Uncertainties Propagation with Depletion

International Nuclear Information System (INIS)

Buiron, L.; Plisson-Rieunier, D.

2015-01-01

In the frame of next generation fast reactor design, the minimisation of nuclear waste production is one of the key objectives for current R and D. Among the possibilities studied at CEA, minor actinides multi-recycling is the most promising industrial way achievable in the near-term. Two main management options are considered: - Multi-recycling in a homogeneous way (minor actinides diluted in the driver fuel). If this solution can help achieving high transmutation rates, the negative impact of minor actinides on safety coefficients allows only a small fraction of the total heavy mass to be loaded in the core (∼ few %). - Multi-recycling in heterogeneous way by means of Minor Actinide Bearing Blanket (MABB) located at the core periphery. This solution offers more flexibility than the previous one, allowing a total minor actinides decoupled management from the core fuel. As the impact on feedback coefficient is small larger initial minor actinide mass can be loaded in this configuration. Starting from a breakeven Sodium Fast Reactor designed jointly by CEA, Areva and EdF teams, the so called SFR V2B, transmutation performances have been studied in frame on the French fleet for both options and various specific isotopic management (all minor actinides, americium only, etc.). Using these results, a sensitivity study has been performed to assess neutronic uncertainties (i.e coming from cross section) on mass balance on the most attractive configurations. This work in based on a new implementation of sensitivity on concentration with depletion in the ERANOS code package. Uncertainties on isotopes masses at the end of irradiation using various variance-covariance is discussed. (authors)

Transmutation of radioactive waste: Effect on the nuclear fuel cycle

International Nuclear Information System (INIS)

Rasmussen, N.C.; Pigford, T.H.

1997-01-01

A committee of the National Research Council reviewed three concepts for transmuting radionuclides recovered from the chemical reprocessing of commercial light-water-reactor (LWR) fuel: LWR transmutation reactors fueled with recycled actinides, advanced liquid-metal reactors (ALMRs), and accelerator-driven subcritical reactors for transmutation of waste (ATW). The concepts were evaluated in terms of: (1) the extent to which waste disposal would benefit from transmutation, (2) time required to reduce the total inventory of radionuclides in the waste and fuel cycle, (3) the complexity of the overall transmutation system, (4) the extent of new development required, and (5) institutional and economic problems of operating such systems. Transmutation could affect geologic disposal of waste by reducing the inventory of transuranics (TRUs), fission products, and other radionuclides in the waste. Reducing the inventory of transuranics does not necessarily affect radiation doses to people who use contaminated ground water if the dissolution rate of transuranics in waste is controlled by elemental solubilities. However, reducing inventories of Am and Pu would decrease potential hazards from human intrusion. The likelihood for underground nuclear criticality would also be reduced. The long-lived fission products Tc-99, I-129, Cs-135 and others typically contribute most to the long-term radiation doses to future populations who use contaminated water from the repository. Their transmutation requires thermal or epithermal neutrons, readily available in LWR and ATW transmutors. ALMR and LWR transmutors would require several hundred years to reduce the total transuranic inventory by even a factor of 10 at constant electric power, and thousands of years for a hundred-fold reduction. For the same electrical power, the ATW could reduce total transuranic inventory about tenfold more rapidly, because of its very high thermal-neutron flux. However, extremely low process losses would be

Measurements of the neutron capture cross sections and incineration potentials of minor-actinides in high thermal neutron fluxes: Impact on the transmutation of nuclear wastes; Mesures des sections efficaces de capture et potentiels d'incineration des actinides mineurs dans les hauts flux de neutrons: Impact sur la transmutation des dechets

Energy Technology Data Exchange (ETDEWEB)

Bringer, O

2007-10-15

This thesis comes within the framework of minor-actinide nuclear transmutation studies. First of all, we have evaluated the impact of minor actinide nuclear data uncertainties within the cases of {sup 241}Am and {sup 237}Np incineration in three different reactor spectra: EFR (fast), GT-MHR (epithermal) and HI-HWR (thermal). The nuclear parameters which give the highest uncertainties were thus highlighted. As a result of fact, we have tried to reduce data uncertainties, in the thermal energy region, for one part of them through experimental campaigns in the moderated high intensity neutron fluxes of ILL reactor (Grenoble). These measurements were focused onto the incineration and transmutation of the americium-241, the curium-244 and the californium-249 isotopes. Finally, the values of 12 different cross sections and the {sup 241}Am isomeric branching ratio were precisely measured at thermal energy point. (author)

Neutron excess generation by fusion neutron source for self-consistency of nuclear energy system

International Nuclear Information System (INIS)

Saito, Masaki; Artisyuk, V.; Chmelev, A.

1999-01-01

The present day fission energy technology faces with the problem of transmutation of dangerous radionuclides that requires neutron excess generation. Nuclear energy system based on fission reactors needs fuel breeding and, therefore, suffers from lack of neutron excess to apply large-scale transmutation option including elimination of fission products. Fusion neutron source (FNS) was proposed to improve neutron balance in the nuclear energy system. Energy associated with the performance of FNS should be small enough to keep the position of neutron excess generator, thus, leaving the role of dominant energy producers to fission reactors. The present paper deals with development of general methodology to estimate the effect of neutron excess generation by FNS on the performance of nuclear energy system as a whole. Multiplication of fusion neutrons in both non-fissionable and fissionable multipliers was considered. Based on the present methodology it was concluded that neutron self-consistency with respect to fuel breeding and transmutation of fission products can be attained with small fraction of energy associated with innovated fusion facilities. (author)

Theoretical and Experimental Research in Neutron Spectra and Nuclear Waste Transmutation on Fast Subcritical Assembly with MOX Fuel

Science.gov (United States)

Arkhipkin, D. A.; Buttsev, V. S.; Chigrinov, S. E.; Kutuev, R. Kh.; Polanski, A.; Rakhno, I. L.; Sissakian, A.; Zulkarneev, R. Ya.; Zulkarneeva, Yu. R.

2003-07-01

The paper deals with theoretical and experimental investigation of transmutation rates for a number of long-lived fission products and minor actinides, as well as with neutron spectra formed in a subcritical assembly driven with the following monodirectional beams: 660-MeV protons and 14-MeV neutrons. In this work, the main objective is the comparison of neutron spectra in the MOX assembly for different external driving sources: a 660-MeV proton accelerator and a 14-MeV neutron generator. The SAD project (JINR, Russia) has being discussed. In the context of this project, a subcritical assembly consisting of a cylindrical lead target surrounded by a cylindrical MOX fuel layer will be constructed. Present conceptual design of the subcritical assembly is based on the core with a nominal unit capacity of 15 kW (thermal). This corresponds to a multiplication coefficient, keff= 0.945, and an accelerator beam power of 0.5 kW. The results of theoretical investigations on the possibility of incinerating long-lived fission products and minor actinides in fast neutron spectrum and formation of neutron spectra with different hardness in subcritical systems based on the MOX subcritical assembly are discussed. Calculated neutron spectra emitted from a lead target irradiated by a 660-MeV protons are also presented.

Fuels and targets for the transmutation of high activity long lived radioactive wastes

International Nuclear Information System (INIS)

Pillon, S.; Warin, D.

2010-01-01

The authors present and comment the different strategies which can be adopted to transmute minor actinides (concerned reactors, in fast breeder reactors, in accelerator driven systems or ADS), and the chemical composition of transmutation fuels (actinide compounds, inert matrices, fuels and targets). They describe the behaviour of refractory ceramic fuels during their service life under irradiation with their different damage origins (neutrons, fission by-products, alpha particles), the fabrication of transmutation fuels and targets through different processes (metallurgical, co-precipitate, sol-gel, wax, infiltration of radioactive materials, VIPAC/SPHEREPAC) and the reprocessing or recycling of these transmutation fuels and targets

Subcritical molten salt reactor with fast/intermediate spectrum for minor actinides transmutation

International Nuclear Information System (INIS)

Degtyarev, Alexey M.; Feinberg, Olga S.; Kolyaskin, Oleg E.; Myasnikov, Andrey A.; Karmanov, Fedor I.; Kuznetsov, Andrey Yu.; Ponomarev, Leonid I.; Seregin, Mikhail B.; Sidorkin, Stanislav F.

2011-01-01

The subcritical molten-salt reactor for transmutation of Am and Cm with the fast-intermediate neutron spectrum is suggested. It is shown that ∼10 such reactor-burners is enough to support the future nuclear power based on the fast reactors as well as for the transmutation of Am and Cm accumulated in the spent fuel storages. (author)

Use of fast reactors for actinide transmutation

International Nuclear Information System (INIS)

1993-03-01

The management of radioactive waste is one of the key issues in today's discussions on nuclear energy, especially the long term disposal of high level radioactive wastes. The recycling of plutonium in liquid metal fast breeder reactors (LMFBRs) would allow 'burning' of the associated extremely long life transuranic waste, particularly actinides, thus reducing the required isolation time for high level waste from tens of thousands of years to hundreds of years for fission products only. The International Working Group on Fast Reactors (IWGFR) decided to include the topic of actinide transmutation in liquid metal fast breeder reactors in its programme. The IAEA organized the Specialists Meeting on Use of Fast Breeder Reactors for Actinide Transmutation in Obninsk, Russian Federation, from 22 to 24 September 1992. The specialists agree that future progress in solving transmutation problems could be achieved by improvements in: Radiochemical partitioning and extraction of the actinides from the spent fuel (at least 98% for Np and Cm and 99.9% for Pu and Am isotopes); technological research and development on the design, fabrication and irradiation of the minor actinides (MAs) containing fuels; nuclear constants measurement and evaluation (selective cross-sections, fission fragments yields, delayed neutron parameters) especially for MA burners; demonstration of the feasibility of the safe and economic MA burner cores; knowledge of the impact of maximum tolerable amount of rare earths in americium containing fuels. Refs, figs and tabs

Neutronics design for lead-bismuth cooled accelerator-driven system for transmutation of minor actinide

International Nuclear Information System (INIS)

Tsujimoto, Kazufumi; Sasa, Toshinobu; Nishihara, Kenji; Oigawa, Hiroyuki; Takano, Hideki

2004-01-01

Neutronics design study was performed for lead-bismuth cooled accelerator-driven system (ADS) to transmute minor actinides. Early study for ADS indicated two problems: a large burnup reactivity swing and a significant peaking factor. To solve these problems, effect of design parameters on neutronics characteristics were searched. The design parameters were initial plutonium loading, buffer region between spallation target and core, and zone fuel loading. Parametric survey calculations were performed considering fuel cycle consisting of burnup and recycle. The results showed that burnup reactivity swing depends on the plutonium fraction in the initial fuel loading, and the lead-bismuth buffer region and the two-zone loading were effective for solving the problems. Moreover, an optimum value for the effective multiplication factor was also evaluated using reactivity coefficients. From the result, the maximum allowable value of the effective multiplication factor for a practical ADS can be set at 0.97. Consequently, a new core concept combining the buffer region and the two-zone loading was proposed base on the results of the parametric survey. (author)

Transmutation of nuclear waste in nuclear reactors

International Nuclear Information System (INIS)

Abrahams, K.; Kloosterman, J.L.; Pilate, S.; Wehmann, U.K.

1996-03-01

The objective of this joint study of ECN, Belgonucleaire, and Siemens is to investigate possibilities for transmutation of nuclear waste in regular nuclear reactors or in special transmutation devices. Studies of possibilities included the limits and technological development steps which would be needed. Burning plutonium in fast reactors, gas-cooled high-temperature reactors and light water reactors (LWR) have been considered. For minor actinides the transmutation rate mainly depends on the content of the minor actinides in the reactor and to a much less degree on the fact whether one uses a homogeneous system (with the actinides mixed into the fuel) or a heterogeneous system. If one wishes to stabilise the amount of actinides from the present LWRs, about 20% of all nuclear power would have to be generated in special burner reactors. It turned out that reactor transmutation of fission products would require considerable recycling efforts and that the time needed for a substantial transmutation would be rather long for the presently available levels of the neutron flux. If one would like to design burner systems which can serve more light water reactors, a large effort would be needed and other burners (possibly driven by accelerators) should be considered. (orig.)

Selection of chemical forms of iodine for transmutation of 129I

International Nuclear Information System (INIS)

Shirasu, Yoshiro; Minato, Kazuo

2003-01-01

To select suitable chemical forms of iodine for the target for transmutation of 129 I, the properties of iodine compounds of NaI, MgI 2 , CaI 2 , CuI and Ca(IO 3 ) 2 were compared and the out-of-reactor heating experiments of the pellets of CuI and Ca(IO 3 ) 2 with the cladding materials were carried out. CuI and Ca(IO 3 ) 2 are not deliquescent but stable in the air, which is of great advantage to construction, operation and maintenance of the processing plants. The cladding with Cu metal liner could be compatible with CuI though the compatibility of the stainless steel with CuI is not good. Ca(IO 3 ) 2 should be deleted from the list of the candidate target materials for the transmutation of 129 I due to the severe chemical reaction with the cladding materials

Development of nuclear transmutation technology - A study on accelerator-driven transmutation of long-lived radionuclide

Energy Technology Data Exchange (ETDEWEB)

Chung, Chang Hyun; Chung, Kie Hyung; Hong, Sang Hee; Hwang, Il Soon; Park, Byung Gi; Yang, Hyung Lyeol; Kim, Duk Kyu; Huh, Chang Wook [Seoul National University, Seoul (Korea, Republic of)

1996-07-01

The objective of this study is to help establish the long-range nuclear waste disposal strategy through the investigations and comparisons of various= concepts of the accelerator-driven nuclear waste transmutation reactors, which have been suggested to replace the geological waste disposal due to the technical uncertainties in the long-time scale. Nuclear data, categorized in high -and low-energy neutron cross-sections, were investigated and the structures, principles, and recent progresses of proton linac were reviews, Also the accelerator power for transmutation and the economics were referred, The comparison of the transmutation concepts concentrated on two: Japanese OMEGA program of alloy fuelled system, Minor actinide molten salt system, and Eutectic alloy system and American ATW program of aqueous system and molten salt system. From the comparative study, a state-of-art of the technology has been identified as a concept employing proton-accelerate of 800 {approx} 1600 MeV with 100 mA capacity combined with liquid lead target, molten salt blanket and on-line chemical separation using centrifuge and electrowinning technology. 34 refs., 25 tabs., 64 figs. (author)

Transmutation of 129I and 237Np using spallation neutrons produced by 1.5, 3.7 and 7.4 GeV protons

International Nuclear Information System (INIS)

Ochs, M.; Schmidt, Th.; Wan, J.-S.

1999-01-01

Small samples of approximately 1 g of 129 I and 237 Np, two long-lived radioactive waste nuclides, were exposed to spallation neutron fluences from relatively small metal targets of lead or uranium, surrounded with a paraffin moderator 6 cm thick irradiated with 1.5, 3.7 and 7.4 GeV protons. The (n, γ) transmutation rates have been determined for the two radioactive waste nuclides. Conventional radiochemical La and U sensors and a variety of solid-state nuclear track detectors were irradiated simultaneously with secondary neutrons. The observed secondary neutron fluences appear to be systematically larger, as compared to the calculations with the well-known cascade codes (LAHET from Los Alamos and DCM-CEM from Dubna)

Fission neutron irradiation of copper containing implanted and transmutation produced helium

DEFF Research Database (Denmark)

Singh, B.N.; Horsewell, A.; Eldrup, Morten Mostgaard

1992-01-01

High purity copper containing approximately 100 appm helium was produced in two ways. In the first, helium was implanted by cyclotron at Harwell at 323 K. In the second method, helium was produced as a transmutation product in 800 MeV proton irradiation at Los Alamos, also at 323 K. The distribut......High purity copper containing approximately 100 appm helium was produced in two ways. In the first, helium was implanted by cyclotron at Harwell at 323 K. In the second method, helium was produced as a transmutation product in 800 MeV proton irradiation at Los Alamos, also at 323 K...... as well as the effect of the presence of other transmutation produced impurity atoms in the 800 MeV proton irradiated copper will be discussed....

Transmutation of Thermocouples in Thermal and Fast Nuclear Reactors

International Nuclear Information System (INIS)

Scervini, M.; Rae, C.; Lindley, B.

2013-06-01

Thermocouples are the most commonly used sensors for temperature measurement in nuclear reactors. Their role is fundamental for the control of current nuclear reactors and for the development of the nuclear technology needed for the implementation of GEN IV nuclear reactors. When used for in-core measurements thermocouples are strongly affected not only by high temperatures, but also by intense neutron fluxes. As a result of the interaction with neutrons, the thermoelements of the thermocouples undergo transmutation, which produces a time dependent change in composition in the thermoelements and, as a consequence, a time dependent drift in the thermocouple signal. Thermocouple drift can be very significant for in-pile temperature measurements and may render the temperature sensors unreliable after exposure to nuclear radiation for relatively short times compared to the life required for temperature sensors in nuclear applications. In this work, undertaken as part of the European project METROFISSION, the change in composition occurring in irradiated thermocouples has been calculated using the software ORIGEN 2.2. Several thermocouples have been considered, including Nickel based thermocouples (type K and type N), Tungsten based thermocouples (W-5%Re vs W-26%Re and W- 3%Re vs W-25%Re), Platinum based thermocouples (type S and Platinum vs Palladium) and Molybdenum vs Niobium thermocouples. The transmutation induced by both thermal flux and fast flux has been calculated. Thermocouples undergo more pronounced transmutation in thermal fluxes rather than in fast fluxes, as the neutron cross section of an element is higher for thermal energies. Nickel based thermocouples have a minimal change in composition, while Platinum based and Tungsten based thermocouples experience a very significant transmutation. The use of coatings deposited on the sheath of a thermocouple has been considered as a mean to reduce the neutron flux the thermoelements inside the thermocouple sheath

Sensitivity analysis of minor actinides transmutation to physical and technological parameters

International Nuclear Information System (INIS)

Kooyman, T.; Buiron, L.

2015-01-01

Minor actinides transmutation is one of the 3 main axis defined by the 2006 French law for management of nuclear waste, along with long-term storage and use of a deep geological repository. Transmutation options for critical systems can be divided in two different approaches: (a) homogeneous transmutation, in which minor actinides are mixed with the fuel. This exhibits the drawback of 'polluting' the entire fuel cycle with minor actinides and also has an important impact on core reactivity coefficients such as Doppler Effect or sodium void worth for fast reactors when the minor actinides fraction increases above 3 to 5% depending on the core; (b) heterogeneous transmutation, in which minor actinides are inserted into transmutation targets which can be located in the center or in the periphery of the core. This presents the advantage of decoupling the management of the minor actinides from the conventional fuel and not impacting the core reactivity coefficients. In both cases, the design and analyses of potential transmutation systems have been carried out in the frame of Gen IV fast reactor using a 'perturbation' approach in which nominal power reactor parameters are modified to accommodate the loading of minor actinides. However, when designing such a transmutation strategy, parameters from all steps of the fuel cycle must be taken into account, such as spent fuel heat load, gamma or neutron sources or fabrication feasibility. Considering a multi-recycling strategy of minor actinides, an analysis of relevant estimators necessary to fully analyze a transmutation strategy has been performed in this work and a sensitivity analysis of these estimators to a broad choice of reactors and fuel cycle parameters has been carried out. No threshold or percolation effects were observed. Saturation of transmutation rate with regards to several parameters has been observed, namely the minor actinides volume fraction and the irradiation time. Estimators of interest that have been

Conceptual design study of Hyb-WT as fusion–fission hybrid reactor for waste transmutation

International Nuclear Information System (INIS)

Siddique, Muhammad Tariq; Kim, Myung Hyun

2014-01-01

Highlights: • Conceptual design study of fusion-fission hybrid reactor for waste transmutation. • MCNPX and MONTEBURNS are compared for transmutation performance of WT-Hyb. • Detailed neutronic performance of final optimized Hyb-WT design is analyzed. • A new tube-in-duct core design is implemented and compared with pin type design. • Study shows many aspects of hybrid reactor even though scope was limited to neutronic analysis. - Abstract: This study proposes a conceptual design of a hybrid reactor for waste transmutation (Hyb-WT). The design of Hyb-WT is based on a low-power tokamak (less than 150 MWt) and an annular ring-shaped reactor core with metal fuel (TRU 60 w/o, Zr 40 w/o) and a fission product (FP) zone. The computational code systems MONTEBURNS and MCNPX2.6 are investigated for their suitability in evaluating the performance of Hyb-WT. The overall design performance of the proposed reactor is determined by considering pin-type and tube-in-duct core designs. The objective of such consideration is to explore the possibilities for enhanced transmutation with reduced wall loading from fusion neutrons and reduced transuranic (TRU) inventory. TRU and FP depletion is analyzed by calculating waste transmutation ratio, mass burned per full power year (in units of kg/fpy), and support ratio. The radio toxicity analysis of TRUs and FPs is performed by calculating the percentage of toxicity reduction in TRU and FP over a burn cycle

Development of long-lived radionuclide transmutation technology - Development of a code system for core analysis of the transmutation reactors

Energy Technology Data Exchange (ETDEWEB)

Cho, Nam Zin; Kim, Yong Hee; Kim, Tae Hyung; Jo, Chang Keun; Park, Chang Je [Korea Advanced Institute of Science and Technology, Taejon (Korea, Republic of)

1996-07-01

The objective of this study is to develop a code system for core analysis= of the critical transmutation reactors utilizing fast neutrons. Core characteristics of the transmutation reactors were identified and four codes, HANCELL for pincell calculation, PRISM and AFEN-H3D for core calculation, and MA{sub B}URN for depletion calculation, were developed. The pincell calculation code is based on one-dimensional collision probability method and may provide homogenized/condensed parameters of a pincell and also can homogenize the control assembly via a nonlinear iterative method. The core calculation codes, PRISM and AFEN-H3D, solve the multi-group, multi-dimensional neutron diffusion equations for a hexagonal geometry and they are based on the finite difference method and analytic function expansion nodal (AFEN) method, respectively. The MA{sub B}URN code san analyze the behavior of actinides and fission products in a reactor core. Through benchmarking, we confirmed that the newly developed codes provide accurate solutions. 30 refs., 10 tabs., 8 figs. (author)

The TARC experiment (PS211): neutron-driven nuclear transmutation by adiabatic resonance crossing

International Nuclear Information System (INIS)

Revol, J.P.; Arnould, H.; Bompas, C.A.

1999-01-01

The main purpose of the TARC experiment is to demonstrate the possibility of using Adiabatic Resonance Crossing (ARC) to destroy efficiently Long-Lived Fission Fragments (LLFFs) in accelerator-driven systems and to validate a new simulation developed in the framework of the Energy Amplifier programme. An experimental set-up was installed in a CERN PS beam line to study how neutrons produced by spallation at relatively high energy (E n ≥1 MeV) slow down quasi adiabatically with almost flat isolethargic energy distribution and reach the capture resonance energy of an element to be transmuted where they will have a high probability of being captured. Precision measurements of energy and space distributions of spallation neutrons (using 2.5 GeV/c and 3.5 GeV/c protons) slowing down in a 3.3 m x 3.3 m x 3 m lead volume and of neutron capture rates of LLFFs 99 Tc, 129 I, and several other elements were performed. An appropriate formalism and appropriate computational tools necessary for the analysis and understanding of the data were developed and validated in detail. Our direct experimental observation of ARC demonstrates the possibility to destroy, in a parasitic mode, outside the Energy Amplifier core, large amounts of 99 Tc or 129 I at a rate exceeding the production rate, thereby making it practical to reduce correspondingly the existing stockpile of LLFFs. In addition, TARC opens up new possibilities for radioactive isotope production as an alternative to nuclear reactors, in particular for medical applications, as well as new possibilities for neutron research and industrial applications. (orig.)

Generation IV and transmutation materials (GETMAT) project: First assessment of selected results

International Nuclear Information System (INIS)

Fazio, Concetta; Serrano, Marta; Gessi, Alessandro; Henry, Jean; Malerba, Lorenzo

2015-01-01

The Generation IV and Transmutation Material (GETMAT) project has been initiated within the 7. EURATOM framework programme with the objective to support the development of innovative reactor designs. Emphasis has been put on the investigation, both in the theoretical and experimental domains, of selected material properties that are cross-cutting among the various Generation IV and Transmutation systems. The selection of the properties to be investigated has been performed by identifying relevant conditions of key components as cores and primary systems. Moreover, taking into account the envisaged conditions of these components it turned out that innovative materials might be a better choice with respect to conventional nuclear grade steels. Therefore, ODS alloys and 9-12 Cr Ferritic/Martensitic (F/M) steels have been selected as reference for the GETMAT project. The R and D activities have been focused on basic characterisation of ODS alloys produced ad hoc for the project and on an extensive PIE programme of F/M steels irradiated in previous programmes. Finally, first principle modelling studies to explain irradiation hardening and embrittlement of F/M alloys were an additional important task. The objective of this manuscript is to make a first assessment of the results obtained within GETMAT. (authors)

Performance of a transmutation advanced device for sustainable energy application

International Nuclear Information System (INIS)

Garcia, C.; Rosales, J.; Garcia, L.; Perez-Navarro, A.; Escriva, A.; Abanades, A.

2009-01-01

Preliminary studies have been performed to design a device for nuclear waste transmutation and hydrogen generation based on a gas cooled pebble bed accelerator driven system, TADSEA (transmutation advanced device for sustainable energy application). In previous studies we have addressed the viability of an ADS Transmutation device that uses as fuel wastes from the existing LWR power plants, encapsulated in graphite in the form of pebble beds, being cooled by helium which enables high temperatures, in the order of 1200 K, to facilitate hydrogen generation from water either by high temperature electrolysis or by thermo chemical cycles. To design this device several configurations were studied, including several reactors thickness, to achieve the desired parameters, the transmutation of nuclear waste and the production of 100 MW. of thermal power. In this paper we are presenting new studies performed on deep burn in-core fuel management strategy for LWR waste. We analyze the fuel cycle on TADSEA device based on driver and transmutation fuel that were proposed for the General Atomic design of a gas turbine-modular helium reactor. We compare the transmutation results of the three fuel management strategies, using driven and transmutation, and standard LWR spend fuel, and present several parameters that describe the neutron performance of TADSEA nuclear core as the fuel and moderator temperature reactivity coefficients and transmutation chain. (author)

Performance of a transmutation advanced device for sustainable energy application

Energy Technology Data Exchange (ETDEWEB)

Garcia, C.; Rosales, J.; Garcia, L. [Instituto Superior de Tecnologias y Ciencias Aplicadas (INSTEC), La Habana (Cuba); Perez-Navarro, A.; Escriva, A. [Universidad Politecnica de Valencia, Valencia (Spain). Inst. de Ingenieria Energetica; Abanades, A. [Universidad Politecnica de Madrid (Spain). Grupo de Modelizacion de Sistemas Termoenergeticos

2009-07-01

Preliminary studies have been performed to design a device for nuclear waste transmutation and hydrogen generation based on a gas cooled pebble bed accelerator driven system, TADSEA (transmutation advanced device for sustainable energy application). In previous studies we have addressed the viability of an ADS Transmutation device that uses as fuel wastes from the existing LWR power plants, encapsulated in graphite in the form of pebble beds, being cooled by helium which enables high temperatures, in the order of 1200 K, to facilitate hydrogen generation from water either by high temperature electrolysis or by thermo chemical cycles. To design this device several configurations were studied, including several reactors thickness, to achieve the desired parameters, the transmutation of nuclear waste and the production of 100 MW. of thermal power. In this paper we are presenting new studies performed on deep burn in-core fuel management strategy for LWR waste. We analyze the fuel cycle on TADSEA device based on driver and transmutation fuel that were proposed for the General Atomic design of a gas turbine-modular helium reactor. We compare the transmutation results of the three fuel management strategies, using driven and transmutation, and standard LWR spend fuel, and present several parameters that describe the neutron performance of TADSEA nuclear core as the fuel and moderator temperature reactivity coefficients and transmutation chain. (author)

System and safety studies of accelerator driven transmutation systems. Annual report 1998

International Nuclear Information System (INIS)

Wallenius, J.; Gudowski, W.; Carlsson, Johan; Eriksson, Marcus; Tucek, K.

1998-12-01

This annual report describes the accelerator-driven transmutation project conducted at the Department of Nuclear and Reactor Physics at the Royal Institute of Technology. The main results are: development of the simulation tools for accelerator-driven transmutation calculations including an integrated Monte-Carlo burnup module and improvements of neutron energy fission yield simulations, processing of the evacuated nuclear data files including preparation of the temperature dependent neutron cross-sections, development of nuclear data for a medium energy range for some isotopes, development of the models and codes for radiation damage simulations, system studies for the spent fuel transmuter, based on heavy metal coolant and advanced nuclear fuel, contribution to the spallation target design being manufactured in IPPE, Obninsk, and accelerator reliability studies. Moreover a lot of efforts were put to further develop existing international collaboration with the most active research groups in the world together with educational activities in Sweden including a number of meetings and workshops and a graduate course in transmutation. This project has been conducted in close collaboration with the EU-project 'Impact of the accelerator based technologies on nuclear fission safety' - IABAT and in bilateral cooperation with different foreign research groups

System and safety studies of accelerator driven transmutation systems. Annual report 1998

Energy Technology Data Exchange (ETDEWEB)

Wallenius, J.; Gudowski, W.; Carlsson, Johan; Eriksson, Marcus; Tucek, K. [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Nuclear and Reactor Physics

1998-12-01

This annual report describes the accelerator-driven transmutation project conducted at the Department of Nuclear and Reactor Physics at the Royal Institute of Technology. The main results are: development of the simulation tools for accelerator-driven transmutation calculations including an integrated Monte-Carlo burnup module and improvements of neutron energy fission yield simulations, processing of the evacuated nuclear data files including preparation of the temperature dependent neutron cross-sections, development of nuclear data for a medium energy range for some isotopes, development of the models and codes for radiation damage simulations, system studies for the spent fuel transmuter, based on heavy metal coolant and advanced nuclear fuel, contribution to the spallation target design being manufactured in IPPE, Obninsk, and accelerator reliability studies. Moreover a lot of efforts were put to further develop existing international collaboration with the most active research groups in the world together with educational activities in Sweden including a number of meetings and workshops and a graduate course in transmutation. This project has been conducted in close collaboration with the EU-project `Impact of the accelerator based technologies on nuclear fission safety` - IABAT and in bilateral cooperation with different foreign research groups 31 refs, 23 figs

Experimental investigations of the accelerator-driven transmutation technologies at the subcritical facility ''Yalina''

International Nuclear Information System (INIS)

Chigrinov, S.E.; Kiyavitskaya, H.I.; Serafimovich, I.G.; Rakhno, I.L.; Rutkovskaia, Ch.K.; Fokov, Y.; Khilmanovich, A.M.; Marstinkevich, B.A.; Bournos, V.V.; Korneev, S.V.; Mazanik, S.E.; Kulikovskaya, A.V.; Korbut, T.P.; Voropaj, N.K.; Zhouk, I.V.; Kievec, M.K.

2002-01-01

The investigations on accelerator-driven transmutation technologies (ADTT) focus on the reduction of the amount of long-lived wastes and the physics of a subcritical system driven with an external neutron source. This paper presents the experimental facility 'Yalina' which was designed and created at the Radiation Physics and Chemistry Problems Institute of the National Academy of Sciences of Belarus in the framework of the ISTC project no. B-070 to study the peculiarities of ADTT in thermal spectrum. A detailed description of the assembly, neutron generator and a preliminary analysis of some calculated and experimental data (multiplication factor, neutron flux density distribution in the assembly, transmutation rates of some long-lived fission products and minor actinides) are presented. (authors)

MA-burners efficiency parameters allowing for the duration of transmutation process

International Nuclear Information System (INIS)

Gulevich, A.; Zemskov, E.; Kalugin, A.; Ponomarev, L.; Seliverstov, V.; Seregin, M.

2010-01-01

Transmutation of minor actinides (MA) means their transforming into the fission products. Usually, MA-burner's transmutation efficiency is characterized by the static parameters only, such as the number of neutrons absorbed and the rate of MA feeding. However, the proper characterization of MA-burner's efficiency additionally requires the consideration of parameters allowing for the duration of the MA transmutation process. Two parameters of that kind are proposed: a) transmutation time τ - mean time period from the moment a mass of MA is loaded into the burner's fuel cycle to be transmuted to the moment this mass is completely transmuted; b) number of reprocessing cycles n rep - effective number of reprocessing cycles a mass of loaded MA has to undergo before being completely transmuted. Some of MA-burners' types have been analyzed from the point of view of these parameters. It turned out that all of them have the value of parameters too high from the practical point of view. It appears that some new approaches to MA-burner's design have to be used to significantly reduce the value of these parameters in order to make the large-scale MA transmutation process practically reasonable. Some of such approaches are proposed and their potential efficiency is discussed. (authors)

Transmutation of {sup 129}I and {sup 237}Np using spallation neutrons produced by 1.5, 3.7 and 7.4 GeV protons

Energy Technology Data Exchange (ETDEWEB)

Wan, J.-S.; Schmidt, T.Th.; Langrock, E.-J.; Vater, P.; Brandt, R. E-mail: brandtr@mailer.uni-marburg.de; Adam, J.; Bradnova, V.; Bamblevski, V.P.; Gelovani, L.; Gridnev, T.D.; Kalinnikov, V.G.; Krivopustov, M.I.; Kulakov, B.A.; Sosnin, A.N.; Perelygin, V.P.; Pronskikh, V.S.; Stegailov, V.I.; Tsoupko-Sitnikov, V.M.; Modolo, G.; Odoj, R.; Phlippen, P.-W.; Zamani-Valassiadou, M.; Adloff, J.C.; Debeauvais, M.; Hashemi-Nezhad, S.R.; Guo, S.-L.; Li, L.; Wang, Y.-L.; Dwivedi, K.K.; Zhuk, I.V.; Boulyga, S.F.; Lomonossova, E.M.; Kievitskaja, A.F.; Rakhno, I.L.; Chigrinov, S.E.; Wilson, W.B

2001-05-11

Small samples of {sup 129}I and {sup 237}Np, two long-lived radwaste nuclides, were exposed to spallation neutron fluences from relatively small metal targets of lead and uranium, that were surrounded with a 6 cm thick paraffin moderator, and irradiated with 1.5, 3.7 and 7.4 GeV protons. The (n,{gamma}) transmutation rates were determined for these nuclides. Conventional radiochemical La- and U-sensors and a variety of solid-state nuclear track detectors were irradiated simultaneously with secondary neutrons. Compared with results from calculations with well-known cascade codes (LAHET from Los Alamos and DCM/CEM from Dubna), the observed secondary neutron fluences are larger.

Transmutation of 239Pu and other nuclides using spallation neutrons produced by relativistic protons reacting with massive U- and Pb- targets

International Nuclear Information System (INIS)

Adam, J.; Balabekyan, A.; Bamblevskij, V.P.

2001-01-01

Experimental studies on the transmutation of some long-lived radioactive waste nuclei, such as 129 I, 237 Np, and 239 Pu, as well as on natural uranium and lanthanum (all of them used as sensors) were carried out at the Synchrophasotron of the Laboratory of High Energies (JINR, Dubna). Spallation neutrons were produced by relativistic protons with energies in the range of 0.5 GeV ≤ E(p) ≤ 1.5 GeV interacting with 20 cm long uranium or lead target stacks. The targets were surrounded by 6 cm paraffin moderators. The radioactive sensors mentioned above were positioned on the outside surface of the moderator and contained typically approximately 0.5 up to 1 gram of long-lived isotopes. The highly radioactive targets were produced perfectly well-sealed in aluminium containers by the Institute of Physics and Power Engineering, Obninsk, Russia. From the experimentally observed transmutation rates one can easily extrapolate, that in a subcritical nuclear power assembly (or 'energy amplifier') using a 10 mA proton beam of 1 GeV onto a Pb-target as used here, one can transmute in one gram samples of the isotope within one month about 3 mg 129 I, 21 mg 237 Np, 3.3 mg 238 U, and 200 mg 239 Pu under the same geometrical conditions. Our observations show, that the transmutation ability of our system increases linearly with the proton energy within the energy interval studied

Research on transmutation and accelerator-driven systems at the Forschungszentrum Karlsruhe

International Nuclear Information System (INIS)

Knebel, J.U.; Heusener, G.

2000-01-01

Transmutation is considered a promising technology worldwide for significantly reducing the amount and, thereby, the long-term radiotoxicity of high active waste (HAW) produced by the operation of nuclear power plants such as light water reactors (LWR). The maximum reduction of radiotoxicity could be by a factor of about 100. Transmutation is thus an alternative to the direct deposition of large volumes of highly radioactive waste. Transmutation presents the possibility of closing the fuel cycle including the minor actinides. Plutonium, minor actinides and long-lived fission products can be transmuted in a so called Accelerator Driven Sub-critical System (ADS), which consists of an accelerator, a target module and a subcritical blanket. This paper describes the work performed at Forschungszentrum Karlsruhe which is critically evaluating an ADS mainly with respect to its potential for transmuting minor actinides, to its feasibility and to safety aspects. The work is being done in the area of core design, neutronics, safety, system analyses, materials and corrosion. (orig.) [de

Results from the TARC experiment: spallation neutron phenomenology in lead and neutron-driven nuclear transmutation by adiabatic resonance crossing

Science.gov (United States)

Abánades, A.; Aleixandre, J.; Andriamonje, S.; Angelopoulos, A.; Apostolakis, A.; Arnould, H.; Belle, E.; Bompas, C. A.; Brozzi, D.; Bueno, J.; Buono, S.; Carminati, F.; Casagrande, F.; Cennini, P.; Collar, J. I.; Cerro, E.; Del Moral, R.; Díez, S.; Dumps, L.; Eleftheriadis, C.; Embid, M.; Fernández, R.; Gálvez, J.; García, J.; Gelès, C.; Giorni, A.; González, E.; González, O.; Goulas, I.; Heuer, D.; Hussonnois, M.; Kadi, Y.; Karaiskos, P.; Kitis, G.; Klapisch, R.; Kokkas, P.; Lacoste, V.; Le Naour, C.; López, C.; Loiseaux, J. M.; Martínez-Val, J. M.; Méplan, O.; Nifenecker, H.; Oropesa, J.; Papadopoulos, I.; Pavlopoulos, P.; Pérez-Enciso, E.; Pérez-Navarro, A.; Perlado, M.; Placci, A.; Poza, M.; Revol, J.-P.; Rubbia, C.; Rubio, J. A.; Sakelliou, L.; Saldaña, F.; Savvidis, E.; Schussler, F.; Sirvent, C.; Tamarit, J.; Trubert, D.; Tzima, A.; Viano, J. B.; Vieira, S.; Vlachoudis, V.; Zioutas, K.

2002-02-01

We summarize here the results of the TARC experiment whose main purpose is to demonstrate the possibility of using Adiabatic Resonance Crossing (ARC) to destroy efficiently Long-Lived Fission Fragments (LLFFs) in accelerator-driven systems and to validate a new simulation developed in the framework of the Energy Amplifier programme. An experimental set-up was installed in a CERN PS proton beam line to study how neutrons produced by spallation at relatively high energy ( E n⩾1 MeV) slow down quasi-adiabatically with almost flat isolethargic energy distribution and reach the capture resonance energy of an element to be transmuted where they will have a high probability of being captured. Precision measurements of energy and space distributions of spallation neutrons (using 2.5 and 3.5 GeV/ c protons) slowing down in a 3.3 m×3.3 m×3 m lead volume and of neutron capture rates on LLFFs 99Tc, 129I, and several other elements were performed. An appropriate formalism and appropriate computational tools necessary for the analysis and understanding of the data were developed and validated in detail. Our direct experimental observation of ARC demonstrates the possibility to destroy, in a parasitic mode, outside the Energy Amplifier core, large amounts of 99Tc or 129I at a rate exceeding the production rate, thereby making it practical to reduce correspondingly the existing stockpile of LLFFs. In addition, TARC opens up new possibilities for radioactive isotope production as an alternative to nuclear reactors, in particular for medical applications, as well as new possibilities for neutron research and industrial applications.

Characterizing Background Events in Neutron Transmutation Doped Thermistors for CUORE-0

Science.gov (United States)

Dutta, Suryabrata; Cuore Collaboration

2017-09-01

The Cryogenic Underground Observatory for Rare Events (CUORE) is a ton-scale neutrinoless double-beta decay experiment operating at the Laboratori Nazionali del Gran Sasso (LNGS). The experiment is comprised of 988 TeO2 bolometric crystals arranged into 19 towers and operated at a temperature of 15 mK. A neutron-transmutation-doped (NTD) Ge thermistor measures the thermal response from particles incident on the crystals. However, bulk and surface contamination of the NTD thermistors themselves produce distorted thermal responses inside the thermistor volume. Although these pulses are efficiently removed from the double-beta decay analysis by pulse shape cuts, they can be used to extract information about thermistor contamination. I will present a multifaceted approach to characterize these events, in which I implement an improved hot-electron thermal model, Geant4 Monte Carlo simulations of background events, and data from a previous experiment, CUORE-0, reprocessed with a new optimal filter. Using this approach, rates and energy deposition from contamination inside the NTD thermistors are measured, giving us better understanding of a CUORE background source.

Actinide partitioning-transmutation program final report. III. Transmutation studies

International Nuclear Information System (INIS)

Wachter, J.W.; Croff, A.G.

1980-07-01

Transmutation of the long-lived nuclides contained in fuel cycle wastes has been suggested as a means of reducing the long-term toxicity of the wastes. A comprehensive program to evaluate the feasibility and incentives for recovering the actinides from wastes (partitioning) and transmuting them to short-lived or stable nuclides has been in progress for 3 years under the direction of Oak Ridge National Laboratory (ORNL). This report constitutes the final assessment of transmutation in support of this program. Included are (1) a summary of recent transmutation literature, (2) a generic evaluation of actinide transmutation in thermal, fast, and other transmutation devices, (3) a preliminary evaluation of 99 Tc and 129 I transmutation, and (4) a characterization of a pressurized-water-reactor fuel cycle with and without provisions for actinide recovery and transmutation for use in other parts of the ORNL program. The principal conclusion of the report is that actinide transmutation is feasible in both thermal and fast reactors, subject to demonstrating satisfactory fuel performance, with relatively little impact on the reactor. It would also appear that additional transmutation studies are unwarranted until a firm decision to proceed with actinide transmutation has been made by the responsible authorities

Partitioning and transmutation (P and D) 1995. A review of the current state of the art

International Nuclear Information System (INIS)

Skaalberg, M.; Landgren, A.; Spjuth, L.; Liljenzin, J.O.; Gudowski, W.

1995-12-01

The recent development in the field of partitioning and transmutation (P/T) is reviewed and evaluated. Current national and international R and D efforts are summarized. Nuclear transmutation with energy production is feasible in nuclear reactors where fast and thermal breeders are the most efficient for transmutation purposes. The operation of subcritical nuclear reactors by high current proton accelerators that generate neutrons in a spallation target is also an interesting option for transmutation and energy production, that has to be more carefully evaluated. These accelerator-driven systems are probably the only solution for the transmutation of long-lived fission products with small neutron capture cross sections and actinide isotopes with small fission cross sections. The requirements on the separation chemistry in the partitioning process depends on the transmutation strategy chosen. Recent developments in aqueous based separation chemistry opens some interesting possibilities to meet some of the requirements, such as separation of different actinides and some fission products and reduction of secondary waste streams. In the advanced accelerator-driven transmutation systems proposed, liquid fuels such as molten salts are considered. The partitioning processes that can be used for these types of fuel will, however, require a long term research program. The possibility to use centrifuge separation is an interesting partitioning option that recently has been proposed. 51 refs, 7 figs, 3 tabs

Copper doping of ZnO crystals by transmutation of 64Zn to 65Cu: An electron paramagnetic resonance and gamma spectroscopy study

Science.gov (United States)

Recker, M. C.; McClory, J. W.; Holston, M. S.; Golden, E. M.; Giles, N. C.; Halliburton, L. E.

2014-06-01

Transmutation of 64Zn to 65Cu has been observed in a ZnO crystal irradiated with neutrons. The crystal was characterized with electron paramagnetic resonance (EPR) before and after the irradiation and with gamma spectroscopy after the irradiation. Major features in the gamma spectrum of the neutron-irradiated crystal included the primary 1115.5 keV gamma ray from the 65Zn decay and the positron annihilation peak at 511 keV. Their presence confirmed the successful transmutation of 64Zn nuclei to 65Cu. Additional direct evidence for transmutation was obtained from the EPR of Cu2+ ions (where 63Cu and 65Cu hyperfine lines are easily resolved). A spectrum from isolated Cu2+ (3d9) ions acquired after the neutron irradiation showed only hyperfine lines from 65Cu nuclei. The absence of 63Cu lines in this Cu2+ spectrum left no doubt that the observed 65Cu signals were due to transmuted 65Cu nuclei created as a result of the neutron irradiation. Small concentrations of copper, in the form of Cu+-H complexes, were inadvertently present in our as-grown ZnO crystal. These Cu+-H complexes are not affected by the neutron irradiation, but they dissociate when a crystal is heated to 900 °C. This behavior allowed EPR to distinguish between the copper initially in the crystal and the copper subsequently produced by the neutron irradiation. In addition to transmutation, a second major effect of the neutron irradiation was the formation of zinc and oxygen vacancies by displacement. These vacancies were observed with EPR.

Optimization of accelerator-driven technology for LWR waste transmutation

International Nuclear Information System (INIS)

Bowman, C.D.

1996-01-01

The role of accelerator-driven transmutation technology is examined in the context of the destruction of actinide waste from commercial light water reactors. It is pointed out that the commercial plutonium is much easier to use for entry-level nuclear weapons than weapons plutonium. Since commercial plutonium is easier to use, since there is very much more of it already, and since it is growing rapidly, the permanent disposition of commercial plutonium is an issue of greater importance than weapons plutonium. The minor actinides inventory, which may be influenced by transmutation, is compared in terms of nuclear properties with commercial and weapons plutonium and for possible utility as weapons material. Fast and thermal spectrum systems are compared as means for destruction of plutonium and the minor actinides. it is shown that the equilibrium fast spectrum actinide inventory is about 100 times larger than for thermal spectrum systems, and that there is about 100 times more weapons-usable material in the fast spectrum system inventory compared to the thermal spectrum system. Finally it is shown that the accelerator size for transmutation can be substantially reduced by design which uses the accelerator-produced neutrons only to initiate the unsustained fission chains characteristic of the subcritical system. The analysis argues for devoting primary attention to the development of thermal spectrum transmutation technology. A thermal spectrum transmuter operating at a fission power of 750-MWth fission power, which is sufficient to destroy the actinide waste from one 3,000-MWth light water reactor, may be driven by a proton beam of 1 GeV energy and a current of 7 mA. This accelerator is within the range of realizable cyclotron technology and is also near the size contemplated for the next generation spallation neutron source under consideration by the US, Europe, and Japan

Spent Nuclear Fuel Option Study on Hybrid Reactor for Waste Transmutation

International Nuclear Information System (INIS)

Hong, Seong Hee; Kim, Myung Hyun

2016-01-01

DUPIC nuclear fuel can be used in hybrid reactor by compensation of subcritical level through (U-10Zr) fuel. Energy production performance of Hyb-WT with DUPIC is grateful because it has high EM factor and performs waste transmutation at the same time. However, waste transmutation performance should be improved by different fissile fuel instead of (U-10Zr) fuel. SNF (Spent Nuclear Fuel) disposal is one of the problems in the nuclear industry. FFHR (Fusion-Fission Hybrid Reactor) is one of the most attractive option on reuse of SNF as a waste transmutation system. Because subcritical system like FFHR has some advantages compared to critical system. Subcritical systems have higher safety potential than critical system. Also, there is suppressed excess reactivity at BOC (Beginning of Cycle) in critical system, on the other hand there is no suppressed reactivity in subcritical system. Our research team could have designed FFHR for waste transmutation; Hyb-WT. Various researches have been conducted on fuel and coolant option for optimization of transmutation performance. However, Hyb-WT has technical disadvantage. It is required fusion power (Pfus) which is the key design parameter in FFHR is increased for compensation of decreasing subcritical level. As a result, structure material integrity is damaged under high irradiation condition by increasing Pfus. Also, deep burn of reprocessed SNF is limited by weakened integrity of structure material. Therefore, in this research, SNF option study will be conducted on DUPIC (Direct Use of Spent PWR Fuel in CANDU Reactor) fuel, TRU fuel and DUPIC + TRU mixed fuel for optimization of Hyb-WT performance. Goal of this research is design check for low required fusion power and high waste transmutation. In this paper, neutronic analysis is conducted on Hyb-WT with DUPIC nuclear fuel. When DUPIC nuclear fuel is loaded in fast neutron system, supplement fissile materials need to be loaded together for compensation of low criticality

Spent Nuclear Fuel Option Study on Hybrid Reactor for Waste Transmutation

Energy Technology Data Exchange (ETDEWEB)

Hong, Seong Hee; Kim, Myung Hyun [Kyung Hee University, Yongin (Korea, Republic of)

2016-05-15

DUPIC nuclear fuel can be used in hybrid reactor by compensation of subcritical level through (U-10Zr) fuel. Energy production performance of Hyb-WT with DUPIC is grateful because it has high EM factor and performs waste transmutation at the same time. However, waste transmutation performance should be improved by different fissile fuel instead of (U-10Zr) fuel. SNF (Spent Nuclear Fuel) disposal is one of the problems in the nuclear industry. FFHR (Fusion-Fission Hybrid Reactor) is one of the most attractive option on reuse of SNF as a waste transmutation system. Because subcritical system like FFHR has some advantages compared to critical system. Subcritical systems have higher safety potential than critical system. Also, there is suppressed excess reactivity at BOC (Beginning of Cycle) in critical system, on the other hand there is no suppressed reactivity in subcritical system. Our research team could have designed FFHR for waste transmutation; Hyb-WT. Various researches have been conducted on fuel and coolant option for optimization of transmutation performance. However, Hyb-WT has technical disadvantage. It is required fusion power (Pfus) which is the key design parameter in FFHR is increased for compensation of decreasing subcritical level. As a result, structure material integrity is damaged under high irradiation condition by increasing Pfus. Also, deep burn of reprocessed SNF is limited by weakened integrity of structure material. Therefore, in this research, SNF option study will be conducted on DUPIC (Direct Use of Spent PWR Fuel in CANDU Reactor) fuel, TRU fuel and DUPIC + TRU mixed fuel for optimization of Hyb-WT performance. Goal of this research is design check for low required fusion power and high waste transmutation. In this paper, neutronic analysis is conducted on Hyb-WT with DUPIC nuclear fuel. When DUPIC nuclear fuel is loaded in fast neutron system, supplement fissile materials need to be loaded together for compensation of low criticality

Concept on coupled spectrum B/T (burning and/or transmutation) reactor for treatment of minor actinides by thermal and fast neutrons

International Nuclear Information System (INIS)

Aziz, Ferhat; Kitamoto, Asashi

1996-01-01

A conceptual design of B/T (burning and/or transmutation) reactor based on a modified conventional 1150 MWe-PWR system, with core consisted of two concentric regions for thermal and fast neutrons, was proposed herein for B/T treatment of MA (minor actinides). The B/T fuel considered was supposed such that MA discharged from 1 GWe-LWR was blended homogeneously with the composition of LWR fuel. In the outer region 23- Np, 241 Am and 243 Am were loaded and burned by thermal neutron, while in the inner region 244 Cm was loaded and burned mainly by fast neutron. The geometry of B/T fuel and the fuel assembly in the outer region was left in the same condition to those of standard PWR while in the inner region the B/T fuel was arranged in the hexagonal geometry, allowed high fuel to coolant volume ratio (V m /V f ), to keep the harder neutron spectrum. Two cases of the Coupled Spectrum B/T Reactor (CSR) with different (V m 1 f ) ratio in the inner region were studied, and the results for the tight lattice with (V m /V f ) = 0.5 showed that those isotopes approached the equilibrium composition after about 5 recycle period, when the CSR was operated under the reactivity swing of 2.8 % dk/k. The evaluations on the void coefficient of reactivity, the Doppler effect and the reactivity swing showed that the CSR concept has the inherent safety and can burn and/or transmute all kind of MA in a single reactor. This CSR can burn about 808 kg of MA in one recycle period of 3 years, which is equivalent to the discharged fuel from about 12 units of LWR in a year. (author)

Research on accelerator-driven transmutation and studies of experimental facilities

Energy Technology Data Exchange (ETDEWEB)

Takizuka, Takakazu [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1997-11-01

JAERI is carrying out R and Ds on accelerator-driven transmutation systems under the national OMEGA Program that aims at development of the technology to improve efficiency and safety in the final disposal of radioactive waste. Research facilities for accelerator-driven transmutation experiments are proposed to construct within the framework of the planned JAERI Neutron Science Project. This paper describes the features of the proposed accelerator-driven transmutation systems and their technical issues to be solved. A research facility plan under examination is presented. The plan is divided in two phases. In the second phase, technical feasibility of accelerator-driven systems will be demonstrated with a 30-60 MW experimental integrated system and with a 7 MW high-power target facility. (author)

MA-burners efficiency parameters allowing for the duration of transmutation process

Energy Technology Data Exchange (ETDEWEB)

Gulevich, A.; Zemskov, E. [Institute of Physics and Power Engineering, Bondarenko Square 1, Obninsk, Kaluga Region 249020 (Russian Federation); Kalugin, A.; Ponomarev, L. [Russian Research Center ' ' Kurchatov Institute' ' Kurchatov Square 1, Moscow 123182 (Russian Federation); Seliverstov, V. [Institute of Theoretical and Experimental Physics ul.B. Cheremushkinskaya 25, Moscow 117259 (Russian Federation); Seregin, M. [Russian Research Institute of Chemical Technology Kashirskoe Shosse 33, Moscow 115230 (Russian Federation)

2010-07-01

Transmutation of minor actinides (MA) means their transforming into the fission products. Usually, MA-burner's transmutation efficiency is characterized by the static parameters only, such as the number of neutrons absorbed and the rate of MA feeding. However, the proper characterization of MA-burner's efficiency additionally requires the consideration of parameters allowing for the duration of the MA transmutation process. Two parameters of that kind are proposed: a) transmutation time {tau} - mean time period from the moment a mass of MA is loaded into the burner's fuel cycle to be transmuted to the moment this mass is completely transmuted; b) number of reprocessing cycles n{sub rep} - effective number of reprocessing cycles a mass of loaded MA has to undergo before being completely transmuted. Some of MA-burners' types have been analyzed from the point of view of these parameters. It turned out that all of them have the value of parameters too high from the practical point of view. It appears that some new approaches to MA-burner's design have to be used to significantly reduce the value of these parameters in order to make the large-scale MA transmutation process practically reasonable. Some of such approaches are proposed and their potential efficiency is discussed. (authors)

An optimization methodology for heterogeneous minor actinides transmutation

Science.gov (United States)

Kooyman, Timothée; Buiron, Laurent; Rimpault, Gérald

2018-04-01

In the case of a closed fuel cycle, minor actinides transmutation can lead to a strong reduction in spent fuel radiotoxicity and decay heat. In the heterogeneous approach, minor actinides are loaded in dedicated targets located at the core periphery so that long-lived minor actinides undergo fission and are turned in shorter-lived fission products. However, such targets require a specific design process due to high helium production in the fuel, high flux gradient at the core periphery and low power production. Additionally, the targets are generally manufactured with a high content in minor actinides in order to compensate for the low flux level at the core periphery. This leads to negative impacts on the fuel cycle in terms of neutron source and decay heat of the irradiated targets, which penalize their handling and reprocessing. In this paper, a simplified methodology for the design of targets is coupled with a method for the optimization of transmutation which takes into account both transmutation performances and fuel cycle impacts. The uncertainties and performances of this methodology are evaluated and shown to be sufficient to carry out scoping studies. An illustration is then made by considering the use of moderating material in the targets, which has a positive impact on the minor actinides consumption but a negative impact both on fuel cycle constraints (higher decay heat and neutron) and on assembly design (higher helium production and lower fuel volume fraction). It is shown that the use of moderating material is an optimal solution of the transmutation problem with regards to consumption and fuel cycle impacts, even when taking geometrical design considerations into account.

Partitioning and transmutation: Radioactive waste management option

International Nuclear Information System (INIS)

Stanculescu, A.

2005-01-01

Growing world population with increasing energy needs, especially in the developing countries, Threat of global warming due to CO 2 emissions demands non-fossil electricity production. Nuclear will have to be part of a sustainable mix of energy production options Figures show that 350 GWe worldwide capacity is 'nuclear'. Present worldwide spent fuel (containing high Pu inventory) and HLW would need large repositories. In view of the previous facts this lecture deals Partitioning and transmutation as radioactive waste management option. Partitioning and transmutation (P and T) is a complex technology i.e. advanced reprocessing, and demand transuranics fuel fabrication plants, as well as innovative and/or dedicated transmutation reactors. In addition to U, Pu, and 129 I, 'partitioning' extracts from the liquid high level waste the minor actinides (MA) and the long-lived fission products (LLFP) 99-Tc, 93-Zr, 135-Cs, 107-Pd, and 79-Se). 'Transmutation' requires fully new fuel fabrication plants and reactor technologies to be developed and implemented on industrial scale. Present LWRs are not suited for MA and LLFP transmutation (safety consideration, plant operation, poor incineration capability). Only specially licensed LWRs can cope with MOX fuel; for increased Pu loadings (up to 100%), special reactor designs (e.g., ABB80+) are required; a combination of these reactor types could allow Pu inventory stabilization. Long-term waste radiotoxicity can be effectively reduced only if transuranics are 'incinerated' through fission with very hard neutron spectra. New reactor concepts (dedicated fast reactors, Accelerator Driven Systems (ADS), fusion/fission hybrid reactors) have been proposed as transmuters/incinerators. Significant Pu+MAs incineration rates can be achieved in symbiotic scenarios: LWR-MOX and dedicated fast reactors; fast neutron spectrum ADS mainly for MA incineration; very high thermal flux ADS concepts could also provide a significant transuranics

Some recent contributions of basic nuclear science to nuclear waste transmutation

International Nuclear Information System (INIS)

Schapira, J.P.

2001-01-01

Nuclear waste transmutation aims at alleviating some long-term risks associated with actinides and with some long-lived fission products. Proposals of using accelerator driven system (ADS) to efficiently burn actinides in uranium free fuels have revitalized some basic researches in the field of nuclear and reactor physics. This is the case for high intensity accelerator in the ADS context and for the neutron source which relies to a large extent on basic nuclear physics related to spallation. There is also an experimental program called MUSE at Cadarache to study the sub-critical reactor physics with regard to its neutronics. A second area where basic research is involved is the measurement of new or more reliable neutron cross sections specific to transmutation and also to the thorium fuel cycle considered as a long-term option for ''clean'' energy production with reduced actinide production. This second area will possibly be covered by a new facility called n-TOF developed at CERN. (author)

Neutron Science Project at JAERI

International Nuclear Information System (INIS)

Oyama, Yukio

1998-01-01

Japan Atomic Energy Research Institute, JAERI, is proposing the Neutron Science Project which aims at bringing about scientific and technological innovation in the fields of basic science and nuclear technology for the 21st century, using high intense spallation neutron source. The research areas to be promoted by the project are neutron structural biology, material science, nuclear physics and various technology developments for accelerator-driven transmutation of long-lived radionuclides which are associated with nuclear power generation. JAERI has been carrying out a R and D program for the partitioning and transmutation with the intention to solve the problem of nuclear fuel cycle backend. The accelerator-driven transmutation study is also covered with this program. In the present stage of the project, a conceptual design is being prepared for a research complex utilizing spallation neutrons, including a high intensity pulsed and steady spallation neutron source with 1.5 GeV and 8 MW superconducting proton linac. The idea and facility plan of the project is described, including the status of technological development of the accelerator, target and facilities. (author)

Neutron Science Project at JAERI

Energy Technology Data Exchange (ETDEWEB)

Oyama, Yukio [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1998-03-01

Japan Atomic Energy Research Institute, JAERI, is proposing the Neutron Science Project which aims at bringing about scientific and technological innovation in the fields of basic science and nuclear technology for the 21st century, using high intense spallation neutron source. The research areas to be promoted by the project are neutron structural biology, material science, nuclear physics and various technology developments for accelerator-driven transmutation of long-lived radionuclides which are associated with nuclear power generation. JAERI has been carrying out a R and D program for the partitioning and transmutation with the intention to solve the problem of nuclear fuel cycle backend. The accelerator-driven transmutation study is also covered with this program. In the present stage of the project, a conceptual design is being prepared for a research complex utilizing spallation neutrons, including a high intensity pulsed and steady spallation neutron source with 1.5 GeV and 8 MW superconducting proton linac. The idea and facility plan of the project is described, including the status of technological development of the accelerator, target and facilities. (author)

Copper doping of ZnO crystals by transmutation of 64Zn to 65Cu: An electron paramagnetic resonance and gamma spectroscopy study

International Nuclear Information System (INIS)

Recker, M. C.; McClory, J. W.; Holston, M. S.; Golden, E. M.; Giles, N. C.; Halliburton, L. E.

2014-01-01

Transmutation of 64 Zn to 65 Cu has been observed in a ZnO crystal irradiated with neutrons. The crystal was characterized with electron paramagnetic resonance (EPR) before and after the irradiation and with gamma spectroscopy after the irradiation. Major features in the gamma spectrum of the neutron-irradiated crystal included the primary 1115.5 keV gamma ray from the 65 Zn decay and the positron annihilation peak at 511 keV. Their presence confirmed the successful transmutation of 64 Zn nuclei to 65 Cu. Additional direct evidence for transmutation was obtained from the EPR of Cu 2+ ions (where 63 Cu and 65 Cu hyperfine lines are easily resolved). A spectrum from isolated Cu 2+ (3d 9 ) ions acquired after the neutron irradiation showed only hyperfine lines from 65 Cu nuclei. The absence of 63 Cu lines in this Cu 2+ spectrum left no doubt that the observed 65 Cu signals were due to transmuted 65 Cu nuclei created as a result of the neutron irradiation. Small concentrations of copper, in the form of Cu + -H complexes, were inadvertently present in our as-grown ZnO crystal. These Cu + -H complexes are not affected by the neutron irradiation, but they dissociate when a crystal is heated to 900 °C. This behavior allowed EPR to distinguish between the copper initially in the crystal and the copper subsequently produced by the neutron irradiation. In addition to transmutation, a second major effect of the neutron irradiation was the formation of zinc and oxygen vacancies by displacement. These vacancies were observed with EPR.

Conceptual Design of Low Fusion Power Hybrid System for Waste Transmutation

Energy Technology Data Exchange (ETDEWEB)

Hong, Seong Hee; Kim, Myung Hyun [Kyung Hee University, Yongin (Korea, Republic of)

2016-10-15

DRUP (Direct Reuse of Used PWR) fuel has same process with DUPIC (Direct Use of spent PWR fuel Into CANDU reactor). There are 2 big benefits by using DRUP fuel in Hybrid system. One is fissile production during operating period. Required power is decreased by fissile production from DRUP fuel. When the fusion power is reduced, integrity of structure materials is not significantly weakened due to reduction of 14.1MeV high energy neutrons. In addition, required amount of tritium for self-sufficiency TBR (Tritium Breeding Ratio ≥ 1.1) is decreased. Therefore, it is possible to further loading the SNF as much as the amount of lithium decreased. It is effective in transmutation. The other one is that DRUP fuel is also SNF. Therefore, using DRUP fuel is reusing of SNF, as a result it makes reduction of SNF from PWR. However, thermal neutron system is suitable for using DRUP fuel compared to fast neutron system. Therefore, transmutation zone designed (U-TRU)Zr fuel and fissile production zone designed DRUP fuel are separated in this study. In this paper, using DRUP fuel for low fusion power in hybrid system is suggested. Fusion power is decreased by using DRUP fuel. As a result, TBR is satisfied design condition despite of using natural lithium. In addition, not only (U-TRU)Zr fuel but also DRUP fuel are transmuted.

Separation and transmutation. A picture of the applications in Sweden; Separation och transmutation. Belysning av tillaempning i Sverige

Energy Technology Data Exchange (ETDEWEB)

Grundfelt, Bertil; Lindgren, Maria [Kemakta Konsult AB, Stockholm (Sweden)

2006-11-15

This report contains a review of the transmutation technology and an elucidation of the consequences of the use of transmutation in Sweden. Transmutation has often been mentioned in the public debate as a way of rendering harmless the high-level waste from nuclear power such that the final disposal of the waste can be substantially simplified or even completely avoided. However, it can be noted that even with an exploitation of transmutation, significant amounts of radioactive waste requiring qualified final disposal will be generated. The transmutation technology will make it possible to reduce the longevity of the high-level waste by converting primarily the transuranic elements to fission products with shorter half lives. The long-term radiotoxicity of the spent nuclear fuel is dominated by the transuranics. Hence, transmutation will lead to a substantial decrease of the long-term radiotoxicity of the spent fuel. The research on transmutation has been focussed on sub-critical so called ADS-reactors (Accelerator Driven System). In such a system protons are accelerated to very high energy levels (in the order of GeV) in an electromagnetic field. The accelerated protons are impacted on a spallation source consisting of heavy atoms, e.g. lead or a mixture of lead and bismuth. At the impact the heavy nuclei are spalled releasing a number of neutrons that can be used for fissioning the nuclei of the substances to be transmuted, primarily the transuranics. ADS-reactors are still at the research stage. It is a common view that it will take several decades before the technology has reached a maturity that allows the construction of a demonstration facility. Calculations performed at Royal Institute of Technology in Stockholm show that using the ADS-technology would allow a reduction of the inventory of transuranics in the spent fuel from Swedish reactors by 50-85% within a 50-100 years period. The goal to transmute 99% of the transuranics inventory has been achieved in

Graphical representation of transmutation and decay chain data, transmutation cross section and delayed gamma ray emission data

International Nuclear Information System (INIS)

Seki, Yasushi; Iida, Hiromasa; Kawasaki, Hiromitsu.

1982-09-01

In a D-T burning fusion reactor, the neutron induced activity severely limits personnel access to the reactor. Accurate evaluation of the induced activity and dose rate is necessary to conduct effective biological shield design. In order to evaluate the dose rate accurately, considerable amount of activation data is required. This report gives graphical representation of transmutation and decay chain data, transmutation cross section data and delayed gamma ray emission data for 116 nuclides of interest in terms of fusion reactor design. This graphical representation was made with hope of producing a reference for examining activation problems. It has already been shown to be effective in correcting inappropriate data. A computer code AMOEBA developed for the checking and plotting of the activation data is also described in this report. (author)

Conceptual design of a fusion-fission hybrid reactor for transmutation of high level nuclear waste

International Nuclear Information System (INIS)

Qiu, L.J.; Wu, Y.C.; Yang, Y.W.; Wu, Y.; Luan, G.S.; Xu, Q.; Guo, Z.J.; Xiao, B.J.

1994-01-01

To assess the feasibility of the transmutation of long-lived radioactive waste using fusion-fission hybrid reactors, we are studying all the possible types of blanket, including a comparison of the thermal and fast neutron spectrum blankets. Conceptual designs of a small tokamak hybrid blanket with small inventory of actinides and fission products are presented. The small inventory of wastes makes the system safer. The small hybrid reactor system based on a fusion core with experimental parameters to be realized in the near future can effectively transmute actinides and fission products at a neutron wall loading of 1MWm -2 . An innovative energy system is also presented, including a fusion driver, fuel breeder, high level waste transmuter, fission reactor and so on. An optimal combination of all types of reactor is proposed in the system. ((orig.))

Monte Carlo method in ADS transmutation reactor coolant and the research of optimal placement of the fuel

International Nuclear Information System (INIS)

Niu Yunlong; Wei Qianglin; Liu Yibao; Wang Aixing; Zhang Peng

2014-01-01

This paper calculated the effects of different coolants to neutron energy spectrum in different position of the transmutation reactor by Monte Carlo N-Particle Transport Code (MCNP5). After having chosen the coolant and particular parameters, different nuclides in fuel rods of the transmutation reactor were calculated and compared. According to the actual situation, nuclides of 99 Tc and 241 Am were chosen and compared. Then the nonuniform-arrangement scheme of different spent fuels were proposed. By comparison of the diagram, it is found that it is more effective to promote the neutron utilization in the reactor by the non-uniform arrangement scheme, which is more reasonable than traditional uniform one. Thus, it would be helpful for transmutation technology by the application of the scheme. (authors)

Requirements for an evaluated nuclear data file for accelerator-based transmutation

International Nuclear Information System (INIS)

Koning, A.J.

1993-06-01

The importance of intermediate-energy nuclear data files as part of a global calculation scheme for accelerator-based transmutation of radioactive waste systems (for instance with an accelerator-driven subcritical reactor) is discussed. A proposal for three intermediate-energy data libraries for incident neutrons and protons is presented: - a data library from 0 to about 100 MeV (first priority), - a reference data library from 20 to 1500 MeV, - an activation/transmutation library from 0 to about 100 MeV. Furthermore, the proposed ENDF-6 structure of each library is given. The data needs for accelerator-based transmutation are translated in terms of the aforementioned intermediate-energy data libraries. This could be a starting point for an ''International Evaluated Nuclear Data File for Transmutation''. This library could also be of interest for other applications in science and technology. Finally, some conclusions and recommendations concerning future evaluation work are given. (orig.)

First experiments on transmutation studies of iodine-129 and neptunium-237 using relativistic protons of 3.7 GeV

International Nuclear Information System (INIS)

Krivopustov, M.I.; Adam, J.; Bradnova, V.

1997-01-01

First experiments on the transmutation of long-lived 129 I and 237 Np using relativistic protons of 3.7 GeV are described. Relativistic protons generate in extended Pb-targets substantial neutron fluences. These neutrons get moderated in paraffin and are used for transmutation as follows: 129 (n, γ) 130 I(β - ) → 130 Xe(stable) and 237 Np(n, γ) 238 Np(β - ) →. The isotopes 130 I (T 1/2 =12.36 h) and 238 Np (T 1/2 =2.117 days) were identified radiochemically. One can estimate the transmutation cross section (n, γ) in the given neutron field as σ( 129 I(n, γ))=(10±2)b and σ( 237 Np(n, γ))=(140±30)b. The experiments were carried out in November 1996 at the Synchrophasotron, Laboratory of High Energies (LHE), Dubna, Russia

Transmutation Capability of a Once-Through Molten-Salt and Other Transmuting Reactors

International Nuclear Information System (INIS)

Greenspan, E.; Lowenthal, M.; Barnes, D.; Kawasaki, D.; Kimball, D.; Matsumoto, H.; Sagara, H.; Vietez, E.R.

2002-01-01

A preliminary assessment is done of the transmutation characteristics of three reactor technologies: a multi-batch liquid metal (LM) cooled transmuter, a once-through molten-salt (MS) transmuter and a pebble bed (PB) transmuter. It was found that for the same fractional transmutation and same k eff drop with burnup (Δk effBU ), lead-bismuth offers smaller peak-to-average core power density, and it requires a smaller pumping power but a larger and heavier core than a sodium cooled transmuter. 99 Tc cannot effectively serve as a burnable absorber to reduce Δk effBU of LM transmuters. However, addition of thorium can greatly flatten k eff and almost double the fractional transmutation of the LWR spent fuel from ∼20% to ∼40%. If the 'once-through' MS transmuter is operated with continuous complete removal of fission products, it can achieve ∼85% fractional transmutation provided that the equilibrium concentration of actinides in the MS can reach 4 mole %. If the fission products are not actively removed, the fractional transmutation is reduced to ∼75%. The fractional transmutation of a PB transmuter can exceed 40%. More thorough analysis is required to better quantify the transmutation capability of the different transmuter technologies. (authors)

Transmutation of Americium in Fast Neutron Facilities

OpenAIRE

Zhang, Youpeng

2011-01-01

In this thesis, the feasibility to use a medium sized sodium cooled fast reactor fully loaded with MOX fuel for efficient transmutation of americium is investigated by simulating the safety performance of a BN600-type fast reactor loaded with different fractions of americium in the fuel, using the safety parameters obtained with the SERPENT Monte Carlo code. The focus is on americium mainly due to its long-term contribution to the radiotoxicity of spent nuclear fuel and its deterioration on c...

Investigation of elements contamination and analysis of electrical effect of this contamination in silicon on the neutron transmutation doping in the RSG-GAS

International Nuclear Information System (INIS)

Sudjadi, U.

1998-01-01

The elements of the contamination on the Neutron Transmutation Doping Process (NTD) have investigated by Multi Channel Analyser (MCA). This Investigation is important to know the quality of silicon doping in NTD. We have found that Mn-45, Ga-72 and Au-198 are elements of contamination in silicon after NTD process. Analysis of electrical effect of this elements contamination on semiconductor silicon is described also in this paper

Neutronic and Logistic Proposal for Transmutation of Plutonium from Spent Nuclear Fuel as Mixed-Oxide Fuel in Existing Light Water Reactors

International Nuclear Information System (INIS)

Trellue, Holly R.

2004-01-01

The use of light water reactors (LWRs) for the destruction of plutonium and other actinides [especially those in spent nuclear fuel (SNF)] is being examined worldwide. One possibility for transmutation of this material is the use of mixed-oxide (MOX) fuel, which is a combination of uranium and plutonium oxides. MOX fuel is used in nuclear reactors worldwide, so a large experience base for its use already exists. However, to limit implementation of SNF transmutation to only a fraction of the LWRs in the United States with a reasonable number of license extensions, full cores of MOX fuel probably are required. This paper addresses the logistics associated with using LWRs for this mission and the design issues required for full cores of MOX fuel. Given limited design modifications, this paper shows that neutronic safety conditions can be met for full cores of MOX fuel with up to 8.3 wt% of plutonium

Use of a multi-attribute utility theory for evaluating the best coolant material in transmutation reactors

International Nuclear Information System (INIS)

Yu, Dong Han; Han, Suk Joong; Kim, Do Hyung; Park, Won Suk

1998-12-01

In order to develop and design a good transmutation system, it is necessary first to select the best available coolant material for a reactor coolant system. Choosing the best coolant material may not be easy since there are several criteria associated with thermal performance, safety problem, cost problem, neutronic aspects. etc. The best option should be chosen based on the maximization of our needs in this situation. It is a challenging task. Decision theory can be employed to solve this type of problem. This report presents the feasibility study for evaluating the best coolant material in transmutation reactors based on the multi=attribute utility theory. The main problem presented here is how to logically evaluate candidate coolant materials under multiple criteria such as thermal performance, safety problem, cost problem, cost problem, neutronic aspects, etc. Since the current problem involves multiple criteria or attributes, first of all, the multi-attribute utility theory (MAUT) such as SMART and AHP has been extensively reviewed. Then, many candidate coolant material for transmutation reactors have been identified. The next step is to construct a value tree that express to reflect the relative importance of the attributes for overall evaluation. Finally, given these assignments, the final goal were obtained by manipulating these ranks through the value tree. The proposed approach is intended to help people be rational and logical in making decisions such complex tasks. (author). 8 refs., 7 tabs., 22 figs

Conceptual study on high performance blanket in a spherical tokamak fusion-driven transmuter

International Nuclear Information System (INIS)

Chen Yixue; Wu Yican

2000-01-01

A preliminary conceptual design on high performance dual-cooled blanket of fusion-driven transmuter is presented based on neutronic calculation. The dual-cooled system has some attractive advantages when utilized in transmutation of HLW (High Level Wastes). The calculation results show that this kind of blanket could safely transmute about 6 ton minor actinides (produced by 170 GW(e) Year PWRs approximately) and 0.4 ton fission products per year, and output 12 GW thermal power. In addition, the variation of power and critical factor of this blanket is relatively little during its 1-year operation period. This blanket is also tritium self-sustainable

Experimental verification of neutron phenomenology in lead and of transmutation by adiabatic resonance crossing in accelerator driven systems a summary of the TARC project at CERN

CERN Document Server

Abánades, A; Andriamonje, Samuel A; Angelopoulos, Angelos; Apostolakis, Alcibiades J; Arnould, H; Belle, E; Bompas, C A; Brozzi, Delecurgo; Bueno, J; Buono, S; Carminati, F; Casagrande, Federico; Cennini, P; Collar, J I; Cerro, E; Del Moral, R; Díez, S; Dumps, Ludwig; Eleftheriadis, C; Embid, M; Fernández, R; Gálvez, J; García, J; Gelès, C; Giorni, A; González, E; González, O; Goulas, I; Heuer, R D; Hussonnois, M; Kadi, Y; Karaiskos, P; Kitis, G; Klapisch, Robert; Kokkas, P; Lacoste, V; Le Naour, C; López, C; Loiseaux, J M; Martínez-Val, J M; Méplan, O; Nifnecker, H; Oropesa, J; Papadopoulos, I M; Pavlopoulos, P; Pérez-Enciso, E; Pérez-Navarro, A; Perlado, M; Placci, Alfredo; Poza, M; Revol, Jean Pierre Charles; Rubbia, Carlo; Rubio, Juan Antonio; Sakelliou, L; Saldaña, F; Savvidis, E; Schussler, F; Sirvent, C; Tamarit, J; Trubert, D; Tzima, A; Viano, J B; Vieira, S L; Vlachoudis, V; Zioutas, Konstantin

2001-01-01

The Transmutation by Adiabatic Resonance Crossing (TARC) experiment was carried out as PS211 at the CERN PS from 1996 to 1999. Energy and space distributions of spallation neutrons (produced by 2.5 and 3.57 GeV/c CERN proton beams) slowing down in a 3.3*3.3*3 m/sup 3/ lead volume and neutron capture rates on long-lived fission fragments /sup 99/Tc and /sup 129/I demonstrate that Adiabatic Resonance Crossing (ARC) can be used to eliminate efficiently such nuclear waste and validate innovative simulation. (9 refs).

Partitioning and transmutation of transuranium elements under nuclear phase-out conditions. Technically reliable?; Transmutation von Transuranen unter den Randbedingungen des Kernenergieausstiegs. Technisch machbar?

Energy Technology Data Exchange (ETDEWEB)

Merk, Bruno; Rohde, Ulrich [Helmholtz-Zentrum Dresden-Rossendorf, Dresden (Germany)

2016-04-15

The German government has decided for the nuclear phase out, but a decision on a strategy for the management of the highly radioactive waste is not defined yet. Partitioning and Transmutation (P and T) could be considered as a technological option in the process of management of highly radioactive waste management, therefore a wide study has been conducted. In this group objectives for P and T and the boundary conditions of the phase out have been discussed. The fulfillment of the given objectives is analyzed using simulations of molten salt reactors with fast neutron spectrum. It is shown that the efficient transmutation of all existing transuranium isotopes would be possible in 3 to 4 reactors in a time frame of 45 to 60 years. Further on a detailed balance of different isotopic inventories is given to allow a deeper understanding of the processes during transmutation.

Safety techniques in the change of nuclear systems. Radiation protection at spallation neutron sources and transmutation facilities

International Nuclear Information System (INIS)

Nuenighoff, Kay

2009-01-01

To push the boundary towards higher neutron fluxes concepts based on spallation reactions have been discussed. Here neutrons are produced by bombarding a heavy metal target (e.g. mercury, tungsten, or tantalum) with high energetic protons. Up to now such facilities could not be realised because of the high power particle accelerators needed. Recent developments of the accelerator technology open the possibility of construction and operating proton accelerators in the MW region. This is demonstrated by construction and commissioning of two MW spallation neutron sources, namely SNS (Oak Ridge, Tennessee, USA) with a power of 1.4 MW and J-PARC (Japan) with 1 MW. The realisation of proton accelerators at this power level will open the way towards energy amplifiers, as proposed e.g. by Carlo Rubbia. Such a facility will not only produce electric power. Furthermore longliving radionuclides can be transmutated into shortlived or even stable nuclides by neutron induced nuclear reactions. A mitigation of the problem of nuclear waste disposal. The above discussed developments prove that accelerators are not only constructed for research, moreover application of these technology became state of the art. With the emergence of particle accelerators in the MW region, radiation protection is confronted with new kind of problems to be solved. Especially the higher kinetic energies of the primary beam particles requires modification and expansion of computer programs well known in nuclear engineering. In contrast to nuclear reactors with kinetic energies up to 2-3 MeV, in spallation reaction secondary particles up to the incident energy in the GeV region will be produced. Problems related to radiation protection have to be considered in an energy range three orders of magnitude higher than known from nuclear reactors. In this thesis existing computer codes are compared and validated with data from selected experiments. Questions concerning radiation protection covers a broad range

Accelerator driven nuclear energy and transmutation systems

International Nuclear Information System (INIS)

Boldeman, J.W.

1999-01-01

Nuclear power generation has been a mature industry for many years. However, despite the overall safety record and the great attractions of nuclear power, especially in times of concern about green house gases emissions, there continues to be some lack of public acceptance of this technology. This sensitivity to nuclear power has several elements in addition to the concern of a potential nuclear accident. These include the possible diversion of plutonium into nuclear weapon production and the concern about the long term storage of plutonium and other transuranic elements. A concept which seeks to allay these fears but still takes advantage of the nuclear fuel cycle and utilises decades of research and development in this technology, is the idea of using modern accelerators to transmute the long lived radio nuclides and simultaneously generate power. A review of the novel concepts for energy production and transmutation of isotopes will be presented. Of the various proposals, the most developed is the Energy Amplifier Concept promoted by Rubbia. The possibility of using high-energy, high-current accelerators to produce large fluxes of neutrons has been known since the earliest days of accelerator technology. E.O. Lawrence, for example, promoted the concept of producing nuclear material with such an accelerator. The Canadians in the early 50s considered using accelerators to produce fuel for their heavy water reactors and there were well advanced designs for a device called the Intense Neutron Generator. The speculative idea of using accelerator produced neutrons for the transmutation of transuranic elements (i.e. elements such as neptunium plutonium and other elements with higher Z atomic number) has also been studied extensively, notably at a number of laboratories in the US, Europe and Japan. However at this time, all facilities that have actually been constructed have been designed primarily for condensed matter studies i.e. studies of the structural properties

Transmutation of nuclear waste. Status report RAS programme 1994: Recycling and transmutation of actinides and fission products

Energy Technology Data Exchange (ETDEWEB)

Cordfunke, E H.P.; Gruppelaar, H; Franken, W M.P.

1995-07-01

This report describes the status and progress of the Dutch RAS programme on `Recycling and Transmutation of Actinides and Fission Products` over the year 1994, which is the first year of the second 4-year programme. This programme is outlined and a short progress report is given over 1994, including a listing of 23 reports and publications over the year 1994. Highlights of 1994 were: The completion of long-lived fission-product transmutation studies, the initiation of small-scale demonstration experiments in the HFR on Tc and I, the issue of reports on the potential of the ALMR (Advanced Liquid Metal Reactor) for transmutation adn the participation and international cooperation on irradiation experiments with actinides in inert matrices. The remaining chapters contain more extended contributions on recent developments and selected topics, under the headings: Benefits and risks of partitioning and transmutation, Perspective of chemical partitioning, Inert matrices, Evolutionary options (MOX), Perspective of heavy water reactors, Perspective of fast burners, Perspective of accelerator-based systems, Thorium cycle, Fission-product transmutation, End scenarios, and Executive summary and recommendations. (orig.).

Transmutation of nuclear waste. Status report RAS programme 1994: Recycling and transmutation of actinides and fission products

International Nuclear Information System (INIS)

Cordfunke, E.H.P.; Gruppelaar, H.; Franken, W.M.P.

1995-07-01

This report describes the status and progress of the Dutch RAS programme on 'Recycling and Transmutation of Actinides and Fission Products' over the year 1994, which is the first year of the second 4-year programme. This programme is outlined and a short progress report is given over 1994, including a listing of 23 reports and publications over the year 1994. Highlights of 1994 were: The completion of long-lived fission-product transmutation studies, the initiation of small-scale demonstration experiments in the HFR on Tc and I, the issue of reports on the potential of the ALMR (Advanced Liquid Metal Reactor) for transmutation adn the participation and international cooperation on irradiation experiments with actinides in inert matrices. The remaining chapters contain more extended contributions on recent developments and selected topics, under the headings: Benefits and risks of partitioning and transmutation, Perspective of chemical partitioning, Inert matrices, Evolutionary options (MOX), Perspective of heavy water reactors, Perspective of fast burners, Perspective of accelerator-based systems, Thorium cycle, Fission-product transmutation, End scenarios, and Executive summary and recommendations. (orig.)

Analysis of the Gas Core Actinide Transmutation Reactor (GCATR)

Science.gov (United States)

Clement, J. D.; Rust, J. H.

1977-01-01

Design power plant studies were carried out for two applications of the plasma core reactor: (1) As a breeder reactor, (2) As a reactor able to transmute actinides effectively. In addition to the above applications the reactor produced electrical power with a high efficiency. A reactor subsystem was designed for each of the two applications. For the breeder reactor, neutronics calculations were carried out for a U-233 plasma core with a molten salt breeding blanket. A reactor was designed with a low critical mass (less than a few hundred kilograms U-233) and a breeding ratio of 1.01. The plasma core actinide transmutation reactor was designed to transmute the nuclear waste from conventional LWR's. The spent fuel is reprocessed during which 100% of Np, Am, Cm, and higher actinides are separated from the other components. These actinides are then manufactured as oxides into zirconium clad fuel rods and charged as fuel assemblies in the reflector region of the plasma core actinide transmutation reactor. In the equilibrium cycle, about 7% of the actinides are directly fissioned away, while about 31% are removed by reprocessing.

Transmutation of radioactive nuclear waste – present status and ...

Indian Academy of Sciences (India)

Transmutation of long-lived actinides and fission products becomes an important issue of the overall nuclear fuel cycle assessment, both for existing and future reactor systems. Reliable nuclear data are required for analysis of associated neutronics. The present paper gives a review of the status of nuclear data analysis ...

High-power proton linac for transmuting the long-lived fission products in nuclear waste

Energy Technology Data Exchange (ETDEWEB)

Lawrence, G.P.

1991-01-01

High power proton linacs are being considered at Los Alamos as drivers for high-flux spallation neutron sources that can be used to transmute the troublesome long-lived fission products in defense nuclear waste. The transmutation scheme being studied provides a high flux (> 10{sup 16}/cm{sup 2}{minus}s) of thermal neutrons, which efficiently converts fission products to stable or short-lived isotopes. A medium-energy proton linac with an average beam power of about 110 MW can burn the accumulated Tc99 and I129 inventory at the DOE's Hanford Site within 30 years. Preliminary concepts for this machine are described. 3 refs., 5 figs., 2 tabs.

Copper doping of ZnO crystals by transmutation of {sup 64}Zn to {sup 65}Cu: An electron paramagnetic resonance and gamma spectroscopy study

Energy Technology Data Exchange (ETDEWEB)

Recker, M. C.; McClory, J. W., E-mail: John.McClory@afit.edu; Holston, M. S.; Golden, E. M.; Giles, N. C. [Department of Engineering Physics, Air Force Institute of Technology, Wright-Patterson Air Force Base, Ohio 45433 (United States); Halliburton, L. E. [Department of Physics and Astronomy, West Virginia University, Morgantown, West Virginia 26506 (United States)

2014-06-28

Transmutation of {sup 64}Zn to {sup 65}Cu has been observed in a ZnO crystal irradiated with neutrons. The crystal was characterized with electron paramagnetic resonance (EPR) before and after the irradiation and with gamma spectroscopy after the irradiation. Major features in the gamma spectrum of the neutron-irradiated crystal included the primary 1115.5 keV gamma ray from the {sup 65}Zn decay and the positron annihilation peak at 511 keV. Their presence confirmed the successful transmutation of {sup 64}Zn nuclei to {sup 65}Cu. Additional direct evidence for transmutation was obtained from the EPR of Cu{sup 2+} ions (where {sup 63}Cu and {sup 65}Cu hyperfine lines are easily resolved). A spectrum from isolated Cu{sup 2+} (3d{sup 9}) ions acquired after the neutron irradiation showed only hyperfine lines from {sup 65}Cu nuclei. The absence of {sup 63}Cu lines in this Cu{sup 2+} spectrum left no doubt that the observed {sup 65}Cu signals were due to transmuted {sup 65}Cu nuclei created as a result of the neutron irradiation. Small concentrations of copper, in the form of Cu{sup +}-H complexes, were inadvertently present in our as-grown ZnO crystal. These Cu{sup +}-H complexes are not affected by the neutron irradiation, but they dissociate when a crystal is heated to 900 °C. This behavior allowed EPR to distinguish between the copper initially in the crystal and the copper subsequently produced by the neutron irradiation. In addition to transmutation, a second major effect of the neutron irradiation was the formation of zinc and oxygen vacancies by displacement. These vacancies were observed with EPR.

Research activities related to accelerator-based transmutation at PSI

International Nuclear Information System (INIS)

Wydler, P.

1993-01-01

Transmutation of actinides and fission products using reactors and other types of nuclear systems may play a role in future waste management schemes. Possible advantages of separation and transmutation are: volume reductions, the re-use of materials, the avoidance of a cumulative risk, and limiting the duration of the risk. With its experience in reactor physics, accelerator-based physics, and the development of the SINQ spallation neutron source, PSI is in a good position to perform basic theoretical and experimental studies relating to the accelerator-based transmutation of actinides. Theoretical studies at PSI have been concentrated, so far, on systems in which protons are used directly to transmute actinides. With such systems and appropriate recycling schemes, the studies showed that considerable reduction factors for long-term toxicity can be obtained. With the aim of solving some specific data and method problems related to these types of systems, a programme of differential and integral measurements at the PSI ring accelerator has been initiated. In a first phase of this programme, thin samples of actinides will be irradiated with 590 MeV protons, using an existing irradiation facility. The generated spallation and fission products will be analysed using different experimental techniques, and the results will be compared with theoretical predictions based on high-energy nucleon-meson transport calculations. The principal motivation for these experiments is to resolve discrepancies observed between calculations based on different high-energy fission models. In a second phase of the programme, it is proposed to study the neutronic behaviour of multiplying target-blanket assemblies with the help of zero-power experiments set up at a separate, dedicated beam line of the accelerator. (author) 3 figs., 2 tabs., 8 refs

Analysis of the transmutational characteristics of a novel molten salt reactor concept

International Nuclear Information System (INIS)

Csom, Gy.; Feher, S.; Szieberth, M.

2001-01-01

One of the arguments most frequently brought up by the opponents of the utilization of nuclear energy is the requirement that the radioactive waste and the long-lived radioisotopes accumulated in the spent fuel should be isolated for a very long time from the biosphere. The solution is the elimination of long-lived actinides (plutonium isotopes and minor actinides) and long-lived fission products by transforming (transmuting) them into short-lived or stable nuclei. The high neutron flux required for transmutation can be realized in nuclear installations. these may be conventional therma; and fast reactors, furthermore dedicated devices, namely thermal and fast reactors and accelerator driven subcritical systems (ADSs), which are specifically designed for this purpose. Some of the most promising systems are the molten salt reactors and subcritical systems, in which the fuel and material to be transmuted circulate dissolved in some molten salt. In the present paper this transmutational device, as well as recommendations for the improvement are discussed in detail (Authors)

Neutron transmutation doping of silicon in the SAFARI-1 research reactor

International Nuclear Information System (INIS)

Louw, P.A.; Robertson, D.G.; Strydom, W.J.

1994-01-01

The SAFARI-1 research reactor has operated with an exemplary safety record since commissioning in 1965. As part of a commercialisation effort a silicon irradiation facility (SILIRAD) has been installed in the poolside region of SAFARI-1 for Neutron Transmutation Doping (NTD) of silicon. Commissioning of the facility took place in the last quarter of 1992 with a series of trial irradiations which were performed in close collaboration with Wacker Chemitronic of Germany. A methodology for the determination of irradiation times necessary to achieve the target resistivities was verified on the basis of the results from the trial irradiations. All production activities are controlled by quality assurance procedures. To date some hundred and twelve silicon ingots (103 mm diameter) have been successfully irradiated on a commercial contract basis. The observed axial and radial variations in the resistivity profile of the ingots are very small compared to the profiles associated with conventionally doped silicon and small tolerances on target resistivities are attained. In this paper an overview of the design and characterisation of SILIRAD is given and the methods applied that ensure a quality product are described. Results obtained from trial and production irradiations are presented and the envisaged future modifications to SILIRAD discussed

Neutron transmutation doping of silicon in the safari-1 research reactor

International Nuclear Information System (INIS)

Louw, P.A.; Robertson, D.G.; Strydom, W.J.

1994-01-01

The SAFARI-1 research reactor has operated with an exemplary safety record since commissioning in 1965. As part of a commercialisation effort a silicon irradiation facility (SILIRAD) has been installed in the poolside region of SAFARI-1 for Neutron Transmutation Doping (NTD) of silicon. Commissioning of the facility took place in the last quarter of 1992 with a series of trial irradiations which were performed in close collaboration the Wacker Chemitronic of Germany. A methodology for the determination of irradiation times necessary to achieve the target resistivities was verified on the basis of the results from the trial irradiations. All production activities are controlled by quality assurance procedures. To date some hundred and twelve silicon ingots (103 mm diameter) have been successfully irradiated on a commercial contract basis. The observed axial and radial variations in the resistivity profile of the ingots are very small compared to the profiles associated with conventionally doped silicon and small tolerances on target resistivities are attained. In this paper an overview of the design and characterisation of SILIRAD is given and the methods applied that ensure a quality product are described. Results obtained from trial and production irradiations are presented and the envisaged future modifications to SILIRAD discussed. 10 refs., 2 tabs., 6 figs

Overview of Neutron Science Project

Energy Technology Data Exchange (ETDEWEB)

Mukaiyama, Takehiko [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1997-11-01

JAERI has launched the Neutron Science Project which aims at bringing scientific and technological innovation for the 21st century in the fields of basic science and nuclear technology using a high power spallation neutron source. The Project is preparing the design for a high intensity pulsed and cw spallation neutron sources for such basic science as neutron structural biology, material science, and for accelerator-driven transmutation of long-lived radio-nuclides which are associated with nuclear power generation. The major facilities to be constructed under the Project are, (1) a super-conducting proton linac with the proton energy of 1.5 GeV and the maximum beam power of 8 MW, (2) a spallation target station with input beam power of 5 MW allowing high intensity pulsed neutron beams for neutron scattering, and (3) research facility complex for accelerator-driven transmutation experiments, neutron physics, material irradiation, isotopes production, spallation produced RI beam experiments for exotic nuclei investigation. (author)

Overview of Neutron Science Project

International Nuclear Information System (INIS)

Mukaiyama, Takehiko

1997-01-01

JAERI has launched the Neutron Science Project which aims at bringing scientific and technological innovation for the 21st century in the fields of basic science and nuclear technology using a high power spallation neutron source. The Project is preparing the design for a high intensity pulsed and cw spallation neutron sources for such basic science as neutron structural biology, material science, and for accelerator-driven transmutation of long-lived radio-nuclides which are associated with nuclear power generation. The major facilities to be constructed under the Project are, 1) a super-conducting proton linac with the proton energy of 1.5 GeV and the maximum beam power of 8 MW, 2) a spallation target station with input beam power of 5 MW allowing high intensity pulsed neutron beams for neutron scattering, and 3) research facility complex for accelerator-driven transmutation experiments, neutron physics, material irradiation, isotopes production, spallation produced RI beam experiments for exotic nuclei investigation. (author)

Design considerations and evaluations of an accelerator-driven fluid fuel transmuter

Energy Technology Data Exchange (ETDEWEB)

Lizana, P.; Lypsch, F.; Phlippen, P.W. [Institute for Safety Research and Reactor Technology, Juelich (Germany)

1995-10-01

A fluid fuel transmuter is proposed on the basis of circulating lead forming the fluid carrier material for long-lived actinides. Thermalization of neutrons is achieved by the use of graphite in the blanket leading to low actinide concentrations, typically around 100 g/l. An eigenvalue of 0.95 is aimed at and the extraneous source neutrons are provided by the interaction of 1.6 GeV protons with a central lead target (spallation process). Fuel depletion and neutron transport calculations are discussed with a view to the technical feasibility and possible advantageous design modifications.

Status of spallation neutron source

Energy Technology Data Exchange (ETDEWEB)

Oyama, Yukio [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1997-03-01

Existing and planned facilities using proton accelerator driven spallation neutron source are reviewed. These include new project of neutron science proposed from Japan Atomic Energy Research Institute. The present status of facility requirement and accelerator technology leads us to new era of neutron science such as neutron scattering research and nuclear transmutation study using very intense neutron source. (author)

Transmutation of $^{239}$Pu and Other Nuclides Using Spallation Neutrons Produced by Relativistic Protons Reacting with Massive U- and Pb-Targets

CERN Document Server

Adam, J; Bamblevski, V P; Barabanov, M Yu; Bradnova, V; Chaloun, P; Hella, K M; Kalinnikov, V G; Krivopustov, M I; Kulakov, B A; Perelygin, V P; Pronskikh, V S; Pavliouk, A V; Solnyshkin, A A; Sosnin, A N; Stegailov, V I; Tsoupko-Sitnikov, V M; Zaverioukha, O S; Adloff, J C; Debeauvais, M; Brandt, R; Langrock, E J; Vater, P; Van, J S; Westmeier, W; Dwivedi, K K; Guo Shi Lun; Li Li Qiang; Hashemi-Nezhad, S R; Kievets, M K; Lomonosova, E M; Zhuk, I V; Modolo, G; Odoj, R; Zamani-Valassiadou, M

2001-01-01

Experimental studies on the transmutation of some long-lived radioactive waste nuclei, such as ^{129}I, ^{237}Np, and ^{239}Pu, as well as on natural uranium and lanthanum (all of them used as sensors) were carried out at the Synchrophasotron of the Laboratory for High Energies (JINR, Dubna). Spallation neutrons were produced by relativistic protons with energies in the range of 0.5 GeV\\le E(p)\\le 1.5 GeV interacting with 20 cm long uranium or lead target stacks. The targets were surrounded by 6 cm paraffin moderators. The radioactive sensors mentioned above were positioned on the outside surface of the moderator and contained typically approximately 0.5 up to 1 gram of long-lived isotopes. The highly radioactive targets were produced perfectly well-sealed in aluminum containers by the Institute of Physics and Power Engineering, Obninsk, Russia. From the experimentally observed transmutation rates one can easily extrapolate, that in a subcritical nuclear power assembly (or "energy amplifier") using a 10 mA pr...

Concept of the demonstration molten salt unit for the transuranium elements transmutations

International Nuclear Information System (INIS)

Alekseev, P.; Dudnikov, A.; Prusakov, V.; Subbotin, S.; Zakirov, R.; Lelek, V.; Peka, I.

1999-01-01

Fluorine reprocessing is discussed of spent fuel and of fluoride molten salt reactor in critical and subcritical modes for plutonium and minor actinides burning. International collaboration for creation of such system is proposed. Additional neutron source in the core will have positive influence on the transmutation processes in the reactor. Demonstration critical molten salt reactor of small power capacity will permit to decide the most part of problems inherent to large critical reactors and subcritical drivers. It could be expected that fluoride molten salt transmuter can work without accelerator as a critical reactor. (author)

Activities performed within the program of nuclear safety research on structural and cladding materials for innovative reactor system able to transmute nuclear waste

International Nuclear Information System (INIS)

Fazio, C.; Rieth, M.; Lindau, R.; Aktaa, J.; Schneider, H-C.; Konys, J.; Yurechko, M.; Mueller, G.; Weisenburger, A.

2009-01-01

The transmutation of nuclear waste to reduce the burden on a geological repository is a relevant topic within the Program of Nuclear Safety Research of the Research Centre Karlsruhe. Several studies have confirmed that a high efficiency of transmutation of actinides is reached in fast neutron spectrum reactor system. Therefore, an important effort is dedicated to the study of transmutation strategies with different fast reactors and their associated technologies. Moreover, in international contexts as Generation IV International Forum (GIF) and Sustainable Nuclear Energy Technology Platform (SNETP), fast reactors are considered in the frame of sustainable development of nuclear energy and reduction of waste. The systems that are currently under investigation, in the frame of the different fuel cycle scenarios, are liquid metal cooled and gas cooled fast reactors as well as Accelerator Driven Sub-critical Transmutation devices (ADS). These innovative reactor systems, call for structural and clad materials, which are able to perform in a safe manner under the envisaged operational and postulated transient conditions. In this context the European Commission supports the FP7 project GETMAT, with the objective to contribute to the development and selection of reference structure materials for core components and primary systems of fast neutron reactors. Several institutes of the Research Centre Karlsruhe are involved in this project with activities in the area of 9Cr ODS steel development and mechanical characterisation; optimisation and ranking of weld and joining techniques as Electron Beam, TIG and Diffusion Bonding; assessment of materials behaviour in corrosive environment and in neutron and neutron/proton irradiation field; and development of corrosion protection barriers for cladding and primary system components and their characterisation. The objective of this contribution is to describe the context in which the GETMAT activities are embedded in the Program

Germanium-doped gallium phosphide obtained by neutron irradiation

Science.gov (United States)

Goldys, E. M.; Barczynska, J.; Godlewski, M.; Sienkiewicz, A.; Heijmink Liesert, B. J.

1993-08-01

Results of electrical, optical, electron spin resonance and optically detected magnetic resonance studies of thermal neutron irradiated and annealed at 800 °C n-type GaP are presented. Evidence is found to support the view that the main dopant introduced via transmutation of GaP, germanium, occupies cation sites and forms neutral donors. This confirms the possibility of neutron transmutation doping of GaP. Simultaneously, it is shown that germanium is absent at cation sites. Presence of other forms of Ge-related defects is deduced from luminescence and absorption data. Some of them are tentatively identified as VGa-GeGa acceptors leading to the self-compensation process. This observation means that the neutron transmutation as a doping method in application to GaP is not as efficient as for Si.

Accelerator-driven transmutation: a high-tech solution to some nuclear waste problems

International Nuclear Information System (INIS)

Hechanova, A.E.

2000-01-01

This paper discusses current technical and political issues regarding the innovative concept of using accelerator-driven transmutation processes for nuclear waste management. Two complex and related issues are addressed. First, the evolution and improvements of the design technologies are identified to indicate that there has been sufficient technological advancement with regard to a 1991 scientific peer review to warrant the advent of a large-scale national research and development program. Second, the economics and politics of the transmutation system are examined to identify non-technical barriers to the implementation of the program. Transmutation of waste has been historically viewed by nuclear engineers as one of those technologies that is too good to be true and probably too expensive to be feasible. The concept discussed in the present paper uses neutrons ( which result from protons accelerated into spallation targets)to transmute the major very long-lived hazardous materials such as the radioactive isotopes of technetium, iodine, neptunium, plutonium, americium, and curium. Although not a new concept, accelerator-driven transmutation technology (ADTT) lead by a team at Los Alamos National Laboratory (LANL) has made some significant advances which are discussed in the present paper. (authors)

A Novel Molten Salt Reactor Concept to Implement the Multi-Step Time-Scheduled Transmutation Strategy

International Nuclear Information System (INIS)

Csom, Gyula; Feher, Sandor; Szieberthj, Mate

2002-01-01

Nowadays the molten salt reactor (MSR) concept seems to revive as one of the most promising systems for the realization of transmutation. In the molten salt reactors and subcritical systems the fuel and material to be transmuted circulate dissolved in some molten salt. The main advantage of this reactor type is the possibility of the continuous feed and reprocessing of the fuel. In the present paper a novel molten salt reactor concept is introduced and its transmutation capabilities are studied. The goal is the development of a transmutation technique along with a device implementing it, which yield higher transmutation efficiencies than that of the known procedures and thus results in radioactive waste whose load on the environment is reduced both in magnitude and time length. The procedure is the multi-step time-scheduled transmutation, in which transformation is done in several consecutive steps of different neutron flux and spectrum. In the new MSR concept, named 'multi-region' MSR (MRMSR), the primary circuit is made up of a few separate loops, in which salt-fuel mixtures of different compositions are circulated. The loop sections constituting the core region are only neutronically and thermally coupled. This new concept makes possible the utilization of the spatial dependence of spectrum as well as the advantageous features of liquid fuel such as the possibility of continuous chemical processing etc. In order to compare a 'conventional' MSR and a proposed MRMSR in terms of efficiency, preliminary calculational results are shown. Further calculations in order to find the optimal implementation of this new concept and to emphasize its other advantageous features are going on. (authors)

ATW neutron spectrum measurements at LAMPF

Energy Technology Data Exchange (ETDEWEB)

Butler, G.W.; Littleton, P.E.; Morgan, G.L. [Los Alamos National Laboratory, NM (United States)] [and others

1995-10-01

Accelerator transmutation of waste (ATW) is a proposal to use a high flux of accelerator-produced thermalized neutrons to transmute both fission product and higher actinide commercial nuclear waste into stable or short-lived radioactive species in order to avoid long-term storage of nuclear waste. At LAMPF the authors recently performed experiments that were designed to measure the spectrum of neutrons produced per incident proton for full-scale proposed ATW targets of lead and lithium. The neutrons produced in such targets have a spectrum of energies that extends up to the energy of the incident proton beam, but the distribution peaks between 1 and 5 MeV. Transmutation reactions and fission of actinides are most efficient when the neutron energy is below a few eV, so the target must be surrounded by a non-absorbing material (blanket) to produce additional neutrons and reduce the energy of high energy neutrons without loss. The experiments with the lead target, 25 cm diameter by 40 cm long, were conducted with 800 MeV protons, while those with the lithium target, 25 cm diameter by 175 cm long, were conducted with 400 MeV protons. The blanket in both sets of experiments was a 60 cm diameter by 200 cm long annulus of lead that surrounded the target. Surrounding the blanket was a steel water tank with dimensions of 250 cm diameter by 300 cm long that simulated the transmutation region. A small sample pipe penetrated the length of the lead blanket and other sample pipes penetrated the length of the water tank at different radii from the beam axis so that the neutron spectra at different locations could be measured by foil activation. After irradiation the activated foil sets were extracted and counted with calibrated high resolution germanium gamma ray detectors at the Los Alamos nuclear chemistry counting facility.

Deep burn transmutation of nuclear waste

International Nuclear Information System (INIS)

Rodriguez, C.; Baxter, A.; McEachern, D.; Venneri, F.; Williams, D.

2002-01-01

Helium-cooled, graphite-moderated reactors with ceramic-coated fuel particles offer unique advantages for the destruction of transuranic materials discharged in Light Water Reactor spent fuel. This is accomplished by fission, and capture-followed-by-fission processes. Three major features make it practical: (1) ceramic-coated particles accommodate high levels of burnup in one pass, thus reducing the need for repeated reprocessing; (2) graphite moderation produces valuable opportunities for thermal and epithermal neutrons to interact with fissionable and non-fissionable materials respectively; and (3) ceramic-coated particle kernel sizes can be adjusted to control the rate of such interactions. In the transmutation scheme proposed here, virtually complete destruction of weapons-usable materials, and 95% destruction of all transuranic waste is achieved. Higher levels of destruction are possible by repeated reprocessing and recycling, but there is little incentive to do so since each reprocessing step generates new secondary waste. After transmutation, the impervious ceramic-coated fuel particles provide an ideal residual waste form. (author)

Oxide fuels and targets for transmutation

International Nuclear Information System (INIS)

Sudreau, F.; Bonnerot, J.M.; Warin, D.; Gaillard-Groleas, G.; Ferroud-Plattet, M.P.

2007-01-01

Full text of publication follows. Direction 1 of the French Act dated 30 December 1991 on the management of high-level, long-lived radioactive waste involves exploring solutions designed to separate long-lived radionuclides from the spent fuel and to transmute them under neutron flux into shorter half-lives or stable elements. In the French research programme conducted by CEA, these radionuclides are mainly minor actinides (americium, neptunium and curium) and fission products (particularly caesium, iodine and technetium). Within this context, this paper aims at illustrating the vast programme that CEA has performed in order to demonstrate the scientific and technical feasibility of minor actinide transmutation. An important part of the research was carried out in collaboration with French research (CNRS) and industrial (EDF, AREVA) organisations, and also in the framework of international co-operation programmes with the European Institute for Transuranium Elements in Karlsruhe (ITU), the US Department of Energy (DOE), the Japanese Atomic Energy Research Institute (now JAEA) and Central Research Institute of Electric Power Industry (CRIEPI) and the Russian Ministry for Atomic Energy (ROSATOM). Such research made it possible to evaluate the capacity of MOX fuels to be used as a support for minor actinide transmutation (homogeneous method). Simulations of pressurised water reactor (PWR) fuels have revealed the limits of this transmutation method, which are mainly related to the pressurization of the fuel rods and the formation of high active californium. On the contrary, for sodium-cooled fast reactor fuels possibly designed with large expansion plenums a first experimental demonstration of the transmutation of americium and neptunium has been successful in the Phenix reactor. Various studies designed to demonstrate the theoretical and experimental feasibility of transmutation using an inert support (heterogeneous method) have been carried out in HFR (EFTTRA

Some neutronics of innovative subcritical assembly with fast neutron spectrum

International Nuclear Information System (INIS)

Kiyavitskaya, H.; Fokov, Yu.; Rutkovskaya, Ch.; Sadovich, S.; Kasuk, D.; Gohar, Y.; Bolshinsky, I.

2013-01-01

Conclusion: • New assembly can be used to: • develop the experimental techniques and adapt the existing ones for monitoring the sub-criticality level, neutron spectra measurements, etc; • study the spatial kinetics of sub-critical and critical systems with fast neutron spectra; • measure the transmutation reaction rates of minor-actinides etc

Project 'Installation of a stand at the horizontal channel of the MARIA Research Reactor, Otwock-Swierk, Poland, for the research of transmutation of minor actinides and fission products'

International Nuclear Information System (INIS)

Szuta, M.

2006-01-01

As a long range objective we would like to focus on management of the fuel economy in the sub-critical assembly of the accelerator driven system (ADS) in terms of long lived fission products (LLFP) and minor actinides (MA) transmutation. Transmutation of the radioactive waste (RW) is an important element within the technical objective of the optimal management of the fuel economy in the sub-critical assembly of the accelerator driven system (ADS). Analysis of possible ways of reduction of radioactive wastes by transmutation of radioactive long-lived fission products such as 99 Tc, 129 I and 135 Cs and by burning up of transuranic nuclides implies that the sub-critical assembly of the accelerator driven system should consist of three zones. The requirement of three zones comes out of the fact that each radioactive isotope to be reduced is to be located in a different spectrum of thermal, epithermal and high energy neutron fluxes. High flux thermal neutron environment (≥10 16 n/cm 3 ·s) is expected as the best way for the transmutation of most of the radioactive waste to stable or short-lived nuclides and for increasing the probability for fission such actinides as 237 Np and 238 Np. The concept of ADS system for energy production and for transmutation is quite new to some extent and from this reason it requires many theoretical and experimental studies. The research of transmutation is a very large area of study requiring a significant experimental and financial support, so it can be performed only within the international cooperation. Specifically, the proposed research within this CRP requires important means, in terms of high-energy proton beams, spallation targets, sub-critical assembly, measurement instrumentation, post-irradiation characterisation and its testing and, of course, manpower for the interpretation of results, modelling observed phenomena, and programme management. The personal involved in the research is to be a skilled personal of

Proposal of a neutron transmutation doping facility for n-type spherical silicon solar cell at high-temperature engineering test reactor.

Science.gov (United States)

Ho, Hai Quan; Honda, Yuki; Motoyama, Mizuki; Hamamoto, Shimpei; Ishii, Toshiaki; Ishitsuka, Etsuo

2018-05-01

The p-type spherical silicon solar cell is a candidate for future solar energy with low fabrication cost, however, its conversion efficiency is only about 10%. The conversion efficiency of a silicon solar cell can be increased by using n-type silicon semiconductor as a substrate. This study proposed a new method of neutron transmutation doping silicon (NTD-Si) for producing the n-type spherical solar cell, in which the Si-particles are irradiated directly instead of the cylinder Si-ingot as in the conventional NTD-Si. By using a 'screw', an identical resistivity could be achieved for the Si-particles without a complicated procedure as in the NTD with Si-ingot. Also, the reactivity and neutron flux swing could be kept to a minimum because of the continuous irradiation of the Si-particles. A high temperature engineering test reactor (HTTR), which is located in Japan, was used as a reference reactor in this study. Neutronic calculations showed that the HTTR has a capability to produce about 40t/EFPY of 10Ωcm resistivity Si-particles for fabrication of the n-type spherical solar cell. Copyright © 2018 Elsevier Ltd. All rights reserved.

Accelerator-driven transmutation reactor analysis code system (ATRAS)

Energy Technology Data Exchange (ETDEWEB)

Sasa, Toshinobu; Tsujimoto, Kazufumi; Takizuka, Takakazu; Takano, Hideki [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1999-03-01

JAERI is proceeding a design study of the hybrid type minor actinide transmutation system which mainly consist of an intense proton accelerator and a fast subcritical core. Neutronics and burnup characteristics of the accelerator-driven system is important from a view point of the maintenance of subcriticality and energy balance during the system operation. To determine those characteristics accurately, it is necessary to involve reactions at high-energy region, which are not treated on ordinary reactor analysis codes. The authors developed a code system named ATRAS to analyze the neutronics and burnup characteristics of accelerator-driven subcritical reactor systems. ATRAS has a function of burnup analysis taking account of the effect of spallation neutron source. ATRAS consists of a spallation analysis code, a neutron transport codes and a burnup analysis code. Utility programs for fuel exchange, pre-processing and post-processing are also incorporated. (author)

Neutron transmutation doping technology of silicon and overview of trial irradiations at Cirus reactor

International Nuclear Information System (INIS)

Singh, Tej; Bhatnagar, Anil; Singh, Kanchhi; Raina, V.K.

2007-12-01

Neutron transmutation doped silicon (NTD-Si) has been used extensively in manufacturing of high power semiconductor devices. The quality of NTD-Si, both from view points of dopant concentration and homogeneity has been found superior to the quality of doped silicon produced by conventional methods. The technology of NTD-Si has been perfected to achieve more accurate resistivity and homogenous resistivity with complete elimination of hot spots. In addition, the greater spatial uniformity, as well as the precise control over the resistivity achievable by using the NTD process, has led to a substantial increase in the breakdown voltage capability of thyristors. The report describes the fundamentals of NTD-Si production and discusses various techniques used for control of dopant concentration and homogeneity. Various aspects like radiation damage, residual radio-activity, nuclear heating, surface contamination and annealing requirements of the silicon ingots after irradiation have also been discussed. Details of trail irradiation and characterization of NTD-Si samples have been provided. Future plans for production of NTD-Si in Cirus and Dhruva reactors have also been discussed. (author)

HYPERFUSE: a hypervelocity inertial confinement system for fusion energy production and fission waste transmutation

International Nuclear Information System (INIS)

Makowitz, H.; Powell, J.R.; Wiswall, R.

1980-01-01

Parametric system studies of an inertial confinement fusion (ICF) reactor system to transmute fission products from an LWR economy have been carried out. The ICF reactors would produce net power in addition to transmuting fission products. The particular ICF concept examined is an impact fusion approach termed HYPERFUSE, in which hypervelocity pellets, traveling on the order of 100 to 300 km/sec, collide with each other or a target block in a reactor chamber and initiate a thermonuclear reaction. The DT fusion fuel is contained in a shell of the material to be transmuted, e.g., 137 Cs, 90 Sr, 129 I, 99 Tc, etc. The 14-MeV fusion neutrons released during the pellet burn cause transmutation reactions (e.g., (n,2n), (n,α), (n,γ), etc.) that convert the long-lived fission products (FP's) either to stable products or to species that decay with a short half-life to a stable product. The transmutation parametric studies conclude that the design of the hypervelocity projectiles should emphasize the achievement of high densities in the transmutation regions (greater than the DT fusion fuel density), as well as the DT ignition and burn criterion (rho R=1.0 to 3.0) requirements

A Comparison of Laser-induced Bremsstrahlung and Laser Compton Scattering for (γ, n) Photo-transmutation of Hazardous Nuclear Waste

International Nuclear Information System (INIS)

Rehman, Haseeb ur; Lee, Jiyoung; Kim, Yonghee

2015-01-01

This paper also presents sensitivity analysis to yield the maximum possible photo-transmutation rates. In general the possibility of radionuclide transmutation using photo-neutron reaction is evaluated in this work. In this paper a detailed methodology to calculate transmutation reaction rates using Laser Induced Bremsstrahlung (LIB) and Laser Compton Scattering (LCS) has been discussed. The methodology was validated by comparing the calculated reaction rates against published data in publically accessed literatures. In the second half of the paper, the authors present a novel concept to narrow down the LCS photon spectrum to an energy range that matches with the resonance region of a particular radionuclide. This is particularly useful considering hazardous waste is usually a mix of different isotopes. As such, being able to tune the LCS photon into any narrow energy range so as to selectively transmute any particular isotope of interest in the hazardous waste mixture would be very desirable. LCS spectrum is highly sensitive to the electron beam energy, laser power, laser luminosity and Compton backscattering angle. From the results it is quite evident that LCS is much better option for the radionuclide transmutation as reaction rates for the LCS is much higher than LIB method even for very small laser power. It can be seen even for the optimistic reaction rate calculations with Bremsstrahlung method reaction rate is much lower than LCS case for 10 Hz repetition rate. If repetition rate of laser 100 Hz then LIB reaction rate has the same order of the magnitude as the reaction rate via LCS. Higher Laser Powers can yield very high transmutation rates

Neutron irradiation effects in fusion or spallation structural materials: Some recent insights related to neutron spectra

International Nuclear Information System (INIS)

Garner, F.A.; Greenwood, L.R.

1998-01-01

A review is presented of recent insights on the role of transmutation in the development of radiation-induced changes in dimension or radiation-induced changes in physical or mechanical properties. It is shown that, in some materials and some neutron spectra, transmutation can significantly affect or even dominate a given property change process. When the process under study is also sensitive to displacement rate, and especially if it involves radiation-induced segregation and precipitation, it becomes much more difficult to separate the transmutation and displacement rate dependencies. This complicates the application of data derived from 'surrogate' spectra to predictions in other flux-spectra environments. It is also shown in this paper that one must be sensitive to the impact of previously -ignored 'small' variations in neutron spectra within a given reactor. In some materials these small variations have major consequences. (author)

Neutron dynamics of fast-spectrum dedicated cores for waste transmutation

International Nuclear Information System (INIS)

Massara, S.

2002-04-01

Among different scenarios achieving minor actinide transmutation, the possibility of double strata scenarios with critical, fast spectrum, dedicated cores must be checked and quantified. In these cores, the waste fraction has to be at the highest level compatible with safety requirements during normal operation and transient conditions. As reactivity coefficients are poor in such critical cores (low delayed neutron fraction and Doppler feed-back, high coolant void coefficient), their dynamic behaviour during transient conditions must be carefully analysed. Three nitride-fuel configurations have been analysed: two liquid metal-cooled (sodium and lead) and a particle-fuel helium-cooled one. A dynamic code, MAT4 DYN, has been developed during the PhD thesis, allowing the study of loss of flow, reactivity insertion and loss of coolant accidents, and taking into account two fuel geometries (cylindrical and spherical) and two thermal-hydraulics models for the coolant (incompressible for liquid metals and compressible for helium). Dynamics calculations have shown that if the fuel nature is appropriately chosen (letting a sufficient margin during transients), this can counterbalance the bad state of reactivity coefficients for liquid metal-cooled cores, thus proving the interest of this kind of concept. On the other side, the gas-cooled core dynamics is very badly affected by the high value of the helium void coefficient (which is a consequence of the choice of a hard spectrum), this effect being amplified by the very low thermal inertia of particle-fuel design. So, a new kind of concept should be considered for a helium-cooled fast-spectrum dedicated core. (authors)

Microcantilever-Enabled Neutron Detection

Directory of Open Access Journals (Sweden)

Kevin R. Kyle

2014-04-01

Full Text Available A new concept for neutron radiation detection was demonstrated using piezoresistive microcantilevers as the active sensing element. Microcantilevers were used to measure the tiny volumetric changes in a sensing material upon absorption of neutron radiation and transmutation into a new element. Highly ordered inorganic crystalline lattices of boron-rich materials dispersed in polymeric rubber matrices were shown to act as volumetric neutron transducers.

Transmutation of radioactive waste with the help of relativistic heavy ions

International Nuclear Information System (INIS)

Brandt, R.; Wan, J.S.; Ochs, M.

1997-01-01

A series of experiments was carried out at the Synchrophasotron, LHE, JINR, Dubna, using 3.67 GeV protons and 18 GeV 12 C ion beams. Two massive lead and uranium targets surrounded by paraffin moderator were irradiated. The outer surface of the moderator was some small U- and La-sensors, to be studied by radiochemistry activation techniques, and also by solid-state nuclear track detectors. Both experimental techniques independently give approximately 28 low energy neutrons on the outer surface of the moderator per 3.67 GeV proton hitting the Pb-target. Theoretical estimations based on LAHET and DCM/CEM computer codes give considerably smaller fluences: approximately 7-9 low energy neutrons ( 129 I(T 1/2 =2.4 days), could be identified radiochemically as well as other spallation products. The transmutation rates are substantial: a 10 mA accelerator of 3.67 GeV protons could transmute at least 30% of 237 Np and 1% of 129 I per month under the given geometrical conditions

HYPERFUSE: a hypervelocity inertial confinement system for fusion energy production and fission waste transmutation

International Nuclear Information System (INIS)

Makowitz, H.; Powell, J.R.; Wiswall, R.

1980-01-01

Parametric system studies of an inertial confinement fusion (ICF) reactor system to transmute fission products from a LWR economy have been carried out. The ICF reactors would produce net power in addition to transmuting fission products. The particular ICF concept examined is an impact fusion approach termed HYPERFUSE, in which hypervelocity pellets, traveling on the order of 100 to 300 km/sec, collide with each other or a target block in a reactor chamber and initiate a thermonuclear reaction. The DT fusion fuel is contained in a shell of the material to be transmuted, e.g., 137 Cs, 90 Sr, 129 I, 99 Tc, etc. The 14-MeV fusion neutrons released during the pellet burn cause transmutation reactions (e.g., (n,2n), (n,α), (n,γ), etc.) that convert the long-lived fission products (FP's) either to stable products or to species that decay with a short half-life to a stable product. The transmutation parametric studies conclude that the design of the hypervelocity projectiles should emphasize the achievement of high densities in the transmutation regions (greater than the DT fusion fuel density), as well as the DT ignition and burn criterion (rho R = 1.0 to 3.0) requirements. These studies also indicate that masses on the order of 1.0 g at densities of rho greater than or equal to 500.0 g/cm 3 are required for a practical fusion-based fission product transmutation system

Waste partitioning and transmutation as a means towards long-term risk reduction

International Nuclear Information System (INIS)

Merz, E.R.

1993-09-01

It has been an idea for some time to reduce the long-term potential hazard of the waste by chemical removal of the actinides as well as some long-lived fission products and their subsequent transmutation in an intense neutron flux. Transmutation would thus shorten the required containment period of radioactive material in a repository. It is estimated, that development of such technology would take at least 40 years because facilities would be required to perform a clean actinide and fission product isolation and to fabricate the fuel elements that contained the separated nuclides. This latter requirements would involve a major expansion of new chemical process steps which are not available as yet. Development of new equipment to maintain occupational exposures as low as reasonably achievable and to minimize releases of radioactivity to the environment would also be necessary. Partitioning and transmutation should be introduced, if at all, as a long-term decision about new nuclear power technology as a future energy source. With regard to this, R and D work dealing with basic questions seems to be worthwhile, However, the introduction of partitioning and transmutation will not eliminate the need for radioactive waste disposal. (orig./HP) [de

Transmutation Technology Development

Energy Technology Data Exchange (ETDEWEB)

Song, T. Y.; Park, W. S.; Kim, Y. H. (and others)

2007-06-15

The spent fuel coming from the PWR is one of the most difficult problems to be solved for the continuous use of nuclear power. It takes a few million years to be safe under the ground. Therefore, it is not easy to take care of the spent fuel for such a long time. Transmutation technology is the key technology which can solve the spent fuel problem basically. Transmutation is to transmute long-lived radioactive nuclides in the spent fuel into short-lived or stable nuclide through nuclear reactions. The long-lived radioactive nuclides can be TRU and fission products such as Tc-99 and I-129. Although the transmutation technology does not make the underground disposal totally unnecessary, the period to take care of the spent fuel can be reduced to the order of a few hundred years. In addition to the environmental benefit, transmutation can be considered to recycle the energy in the spent fuel since the transmutation is performed through nuclear fission reaction of the TRU in the spent fuel. Therefore, transmutation technology is worth being developed in economical aspect. The results of this work can be a basis for the next stage research. The objective of the third stage research was to complete the core conceptual design and verification of the key technologies. The final results will contribute to the establishment of Korean back end fuel cycle policy by providing technical guidelines.

Evaluation of systems incorporating transmutation for the reduction of the long term toxicity of high-level waste

International Nuclear Information System (INIS)

Davidson, J.W.

1979-01-01

One of the alternative high-level nuclear waste (HLW) management/disposal concepts proposed involves the separation from HLW of the elements with isotopes which dominate the radiotoxicity and the transmutation of these nuclides to shortlived or stable products. The waste management system required for transmutation employs chemical processing of HLW to recover waste nuclides for irradiation with neutrons in a transmutation device. The transmuter periodically requires replenishment of the target nuclides and chemical processing to remove the transmutation products. The waste streams from HLW processing and product recovery together comprise the discharge from the system. An imploding liner fusion reactor (ILFR) is assumed for the transmuter with the waste nuclides dissolved in a molten lead-lithium alloy blanket. The potential transmutation candidates are defined as the elements with toxicities per unit volume (toxicity indexes) in solidified HLW at 1000 years which are greater than that for 0.2% uranium ore (carnotite). The candidates which require separation for transmutation are the actinides; Np, Pu, Am, and Cu and the fission products; I and Tc. Certain assumptions were made for the parameters for the ILFR and its operating conditions, and a system evaluation was done. System evaluations indicate that blanket waste loadings on the order of several percent of the total concentration result in attractive performance in terms of high transmutation capacities and low blanket processing requirments. It appears that transmutation system goals in terms of toxicity reduction are achievable with a modest number of transmuters. In addition, requirements for transmuter performance, chemical processing capacity and chemical separation efficiency appear to be within projected values for this technology

Fusion-Fission Transmutation Scheme-Efficient destruction of nuclear waste

International Nuclear Information System (INIS)

Kotschenreuther, M.; Valanju, P.M.; Mahajan, S.M.; Schneider, E.A.

2009-01-01

A fusion-assisted transmutation system for the destruction of transuranic nuclear waste is developed by combining a subcritical fusion-fission hybrid assembly uniquely equipped to burn the worst thermal nonfissile transuranic isotopes with a new fuel cycle that uses cheaper light water reactors for most of the transmutation. The center piece of this fuel cycle, the high power density compact fusion neutron source (100 MW, outer radius <3 m), is made possible by a new divertor with a heat-handling capacity five times that of the standard alternative. The number of hybrids needed to destroy a given amount of waste is an order of magnitude below the corresponding number of critical fast-spectrum reactors (FRs) as the latter cannot fully exploit the new fuel cycle. Also, the time needed for 99% transuranic waste destruction reduces from centuries (with FR) to decades

A repository released-dose model for the evaluation of long-lived fission product transmutation effectiveness

International Nuclear Information System (INIS)

Davidson, J.W.

1995-01-01

A methodology has been developed to quantify the total integrated dose due to a radionuclide species i emplaced in a geologic repository; the focus is on the seven long-lived fission products (LLFPs). The methodology assumes continuous exposure water contaminated with species i at the accessible environment (i.e., just beyond the geologic barrier afforded by the geologic repository). The dose integration is performed out to a reference post-release time. The integrated dose is a function of the total initial inventory of radionuclide i the repository, the time at which complete and instantaneous failure of the engineered barrier (e.g., waste canister) in, a geologic repository occurs, the fractional dissolution rate (from waste solid form) of radionuclide i in ground water, the ground water travel time to the accessible environment, the retardation factor (sorption on the geologic media) for radionuclide i, the time after radionuclide begins to enter the biosphere. In order to assess relative dose, the ratio of total integrated dose to that for a reference LLFP species j (e.g., 99 Tc) was defined. This ratio is a measure of the relative benefit of transmutation of other LLFPs compared to 99 Tc. This methodology was further developed in order to quantify the integrated dose reduction per neutron utilized for LLFP transmutation in accelerator-driven transmutation technologies (ADTT). This measure of effectiveness is a function of the integrated dose due to LLFP species i, the number of total captures in LLFP species i chain per LLFP nuclide fed to the chain at equilibrium, and the number of total captures in related transmutation product (TP) chains per capture in the LLFP species i chain. To assess relative transmutation effectiveness, the ratio of integrated dose reduction per neutron utilization to that for a reference LLFP species j (e.g., 99 Tc) was defined. This relative measure of effectiveness was evaluated LLFP transmutation strategy

Partitioning and transmutation. Current developments - 2007. A report from the Swedish reference group on P-T-research

International Nuclear Information System (INIS)

Ahlstroem, Per-Eric; Blomgren, Jan; Eriksson, Marcus; Seltborg, Per; Wallenius, Jan; Westlen, Daniel

2007-06-01

stability against hydrolysis and radiolysis. This may be achieved either by additives to the solvent or by selection of a proper solvent. The development of processes and equipment must be intensified. Pyrochemical research is looking into methods for recovery of uranium and for separating fission products with large neutron cross sections. The objective is to avoid separation of plutonium from other transuranium elements and thus simplify the proliferation issue. Beside the design studies the main part of the R and D-efforts for transmutation are devoted to studies of fuel and materials. The results from these efforts are applicable to fast reactors as well as accelerator-driven systems. Some recent status of these studies are summarised in the report

Partitioning and transmutation. Current developments - 2007. A report from the Swedish reference group on P-T-research

Energy Technology Data Exchange (ETDEWEB)

Ahlstroem, Per-Eric (ed.) [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Blomgren, Jan [Uppsala Univ. (Sweden). Dept. of Neutron Research; Ekberg, Christian; Englund, Sofie; Fermvik, Anna; Liljenzin, Jan-Olov; Retegan, Teodora; Skarnemark, Gunnar [Chalmers Univ. of Technology, Goeteborg (Sweden); Eriksson, Marcus; Seltborg, Per; Wallenius, Jan; Westlen, Daniel [Royal Inst. of Technology, Stockholm (Sweden)

2007-06-15

stability against hydrolysis and radiolysis. This may be achieved either by additives to the solvent or by selection of a proper solvent. The development of processes and equipment must be intensified. Pyrochemical research is looking into methods for recovery of uranium and for separating fission products with large neutron cross sections. The objective is to avoid separation of plutonium from other transuranium elements and thus simplify the proliferation issue. Beside the design studies the main part of the R and D-efforts for transmutation are devoted to studies of fuel and materials. The results from these efforts are applicable to fast reactors as well as accelerator-driven systems. Some recent status of these studies are summarised in the report.

Progress in transmutation targets from Efttra

International Nuclear Information System (INIS)

Haas, D.; Fernandez, A.; Warin, D.; Bonnerot, J.M.; Garzenne, C.; Scaffidi-Argentina, F.; Maschek, W.; Schram, R.; Klaassen, F.

2007-01-01

Since 15 years, the EFTTRA partners have organised programmes to demonstrate the feasibility of the transmutation of americium in uranium-free targets. In the related transmutation scenario, the targets are introduced in a thermal neutron zone of a fast reactor, to maximize the efficiency of transmutation. Amongst these programmes, those carried out in the HFR reactor in Petten have led to important conclusions and are still at the core of the research in that field. The analysis of the EFTTRA T4 and T4bis irradiation experiments, carried out with targets of MgAl 2 O 4 +11 wt% 241 Am, showed that the release/trapping of helium is the key issue for target design, and also demonstrated a lack of technical benefits of this material, due to a unsatisfactory in-pile behaviour in terms of irradiation damage and chemical stability. A new irradiation experiment called HELIOS is currently under fabrication and will be carried out in HFR. The in-pile behaviour of U-free fuels and targets such as (Am,Zr)O 2 , (Pu,Am,Zr)O 2 , CERCER (MgO) or CERMET (Mo) will be examined. The irradiation temperature will be high enough in some of the pins to be able to tune the release of a significant fraction of helium produced so that the material swelling can be minimized as much as reasonably possible. The HELIOS irradiation experiment is planned to be carried out in the HFR core and shall last 300 full power days starting in 2007. (authors)

Nuclear Waste Separation and Transmutation Research with Special Focus on Russian Transmutation Projects Sponsored by ISTC

International Nuclear Information System (INIS)

Conde, Henri; Blomgren, Jan; Olsson, Nils

2003-03-01

for transmutation of long lived nuclear waste should be carried through on about the same level as present (5 MSEK/year). Support is also given for participation in international projects, primarily EU projects. The aim of the research is to provide knowledgeable experts in the field to assess the international research and development on transmutation. Swedish transmutation research, in general fundamental research, are performed at three universities CTH, KTH and Uppsala University with the essential support from SKB, SKI and Swedish Nuclear Technology Centre. The same university groups are also participating in a number of international transmutation related research projects, in particular, the projects under the 5th Framework Programme of the European Commission. One of the main issues of the International Science and Technology Center (ISTC) in Moscow, which is financially supported by USA, EU, Russia, Japan, South Korea and Norway, is to reduce the proliferation risk by engaging experts at the former Soviet Union nuclear weapon laboratories in civilian research. This issue has been more pronounced since the terrorist attacks on September 11, 2001 and the following threats from the same group of terrorists. At a workshop in Saltsjoebaden in 1991 on Accelerator Based Radioactive Waste Transmutation it was concluded that research on incineration and transmutation of reactor- and weapons grade plutonium was a civilian research area well suited to occupy the former USSR weapon experts with support from ISTC. The Expert Group on Transmutation/SKI Reference Group has chosen to initiate ISTC projects, which are dealing with fundamental technical issues for the accelerator driven transmutation concepts. The possibility of finding a Swedish research group as a counterpart to the Russian group has also played a role in the reference group's selection of projects. The Swedish research groups from CTH, KTH and UU are at present collaborating in 9 transmutation projects

HYPERFUSE: a novel inertial confinement system utilizing hypervelocity projectiles for fusion energy production and fission waste transmutation

International Nuclear Information System (INIS)

Makowitz, H.; Powell, J.R.; Wiswall, R.

1980-01-01

Parametric system studies of an inertial confinement fusion (ICF) reactor system to transmute fission products from an LWR economy have been carried out. The ICF reactors would produce net power in addition to transmuting fission products. The particular ICF concept examined is an impact fusion approach termed HYPERFUSE, in which hypervelocity pellets, traveling on the order of 100 to 300 km/sec, collide with each other or a target block in a reactor chamber and initiate a thermonuclear reaction. The DT fusion fuel is contained in a shell of the material to be transmuted, e.g., 137 Cs or 90 Sr. The 14-MeV fusion neutrons released during the pellet burn cause transmutation reactions (e.g., (n, 2n), (n, α), etc.) that convert the long lived fission products (FP's) either to stable products or to species that decay with a short half-life to a stable product

Inelastic scattering of fast neutrons on Fe-56; Inelastische Streuung schneller Neutronen an {sup 56}Fe

Energy Technology Data Exchange (ETDEWEB)

Beyer, Roland

2014-11-24

The relevant reaction cross sections for the nuclear transmutation will be measured at the neutron flight time facility nELBE in Dresden-Rossendorf. Transmutation by fast neutron irradiation is supposed to reduce the radiotoxicity of high-level radioactive wastes. The thesis is aimed to measure the inelastic neutron scattering cross sections of Fe-56 using a new double flight-time method. With combined plastic and BaF2 scintillation detectors for the first time the emitted neutrons and photons are observed in coincidence.

Transmutation potential of reactor WWER-440

International Nuclear Information System (INIS)

Darilek, P.; Sebian, V.; Necas, V.

2001-01-01

Theoretical evaluation of WWER-440 transmutation potential by HELIOS - code is presented. Transmutation method proposal comprising special transmutation pins, combined FA and simple reprocessing is described. Transmutation efficiency of the method is characterized (Authors)

Waste transmutation and public acceptance

International Nuclear Information System (INIS)

Pigford, T.H.

1991-01-01

The concept of transmuting radioactive wastes with reactors or accelerators is appealing. It has the potential of simplifying or eliminating problems of disposing of nuclear waste. The transmutation concept has been renewed vigorously at a time when national projects to dispose of high-level and transuranic waste are seriously delayed. In this period of tightening federal funds and program curtailments, skilled technical staffs are available at US Department of Energy (DOE) national laboratories and contractors to work on waste transmutation. If the claims of transmutation can be shown to be realistic, economically feasible, and capable of being implemented within the US institutional infrastructure, public acceptance of nuclear waste disposal may be enhanced. If the claims for transmutation are not substantiated, however, there will result a serious loss of credibility and an unjust exacerbation of public concerns about nuclear waste. The paper discusses the following topics: how public acceptance is achieved; the technical community and waste disposal; transmutation and technical communication; transmutation issues; technical fixes and public perception

The role of Z-pinch fusion transmutation of waste in the nuclear fuel cycle

International Nuclear Information System (INIS)

Smith, James Dean; Drennen, Thomas E.; Rochau, Gary Eugene; Martin, William Joseph; Kamery, William; Phruksarojanakun, Phiphat; Grady, Ryan; Cipiti, Benjamin B.; Wilson, Paul Philip Hood; Mehlhorn, Thomas Alan; Guild-Bingham, Avery; Tsvetkov, Pavel Valeryevich

2007-01-01

The resurgence of interest in reprocessing in the United States with the Global Nuclear Energy Partnership has led to a renewed look at technologies for transmuting nuclear waste. Sandia National Laboratories has been investigating the use of a Z-Pinch fusion driver to burn actinide waste in a sub-critical reactor. The baseline design has been modified to solve some of the engineering issues that were identified in the first year of work, including neutron damage and fuel heating. An on-line control feature was added to the reactor to maintain a constant neutron multiplication with time. The transmutation modeling effort has been optimized to produce more accurate results. In addition, more attention was focused on the integration of this burner option within the fuel cycle including an investigation of overall costs. This report presents the updated reactor design, which is able to burn 1320 kg of actinides per year while producing 3,000 MWth

Evaluation of the possibility of plutonium and minor actinides transmutation in HWR

International Nuclear Information System (INIS)

Ghitescu, P.; Ghizdeanu, N. B.

2008-01-01

Partitioning and Transmutation (P and T) techniques could contribute to reduce the radioactive inventory and its associated radio-toxicity. Until now, for this purpose were studied ADS and/or FBR, but not HWR. There are several developed computer codes that analyze the inventory of the radio-nuclides in spent fuel before and after transmutation. WIMSD code is a deterministic lattice spectrum code, which can analyze the reactor neutronic behaviour It also has the capacity to generate burn up and can calculate the inventory of the radio-nuclides of the spent fuel. The advantage of WIMSD code is the variety of the created geometries, together with the big amount of calculated information (K-infinite, macroscopic cross-sections, burnable material radioactive inventory etc). Starting from WIMSD code, the paper presents a model, which simulates the possibility of fuel transmutation in PHWRs. First step was to propose a model, which simulates a CANDU reactor lattice and calculate the radionuclides inventory in an irradiated CANDU fuel bundle. The results were compared with the existing experimental data from CANDU reactors and the calculated parameters were found to be in good agreement with them. After the validation, several simulations were made for PHWRs in order to establish the optimal parameters, related to the efficiency of the transmutation process. Therefore, the code was used for a new type of fuel, containing Plutonium and minor actinides that could be transmuted. The new radioactive inventories were calculated. The simulations showed that Pu content decreases up to 8% in a CANDU reactor and 25% in an ACR. Thus, ACR can reduce the Plutonium inventory from MOX fuel and could be a transmutation solution. (authors)

Semiconductor research with reactor neutrons

International Nuclear Information System (INIS)

Kimura, Itsuro

1992-01-01

Reactor neutrons play an important role for characterization of semiconductor materials as same as other advanced materials. On the other hand reactor neutrons bring about not only malignant irradiation effects called radiation damage, but also useful effects such as neutron transmutation doping and defect formation for opto-electronics. Research works on semiconductor materials with the reactor neutrons of the Kyoto University Reactor (KUR) are briefly reviewed. In this review, a stress is laid on the present author's works. (author)

Actinide partitioning-transmutation program final report. I. Overall assessment

International Nuclear Information System (INIS)

Croff, A.G.; Blomeke, J.O.; Finney, B.C.

1980-06-01

This report is concerned with an overall assessment of the feasibility of and incentives for partitioning (recovering) long-lived nuclides from fuel reprocessing and fuel refabrication plant radioactive wastes and transmuting them to shorter-lived or stable nuclides by neutron irradiation. The principal class of nuclides considered is the actinides, although a brief analysis is given of the partitioning and transmutation (P-T) of 99 Tc and 129 I. The results obtained in this program permit us to make a comparison of the impacts of waste management with and without actinide recovery and transmutation. Three major conclusions concerning technical feasibility can be drawn from the assessment: (1) actinide P-T is feasible, subject to the acceptability of fuels containing recycle actinides; (2) technetium P-T is feasible if satisfactory partitioning processes can be developed and satisfactory fuels identified (no studies have been made in this area); and (3) iodine P-T is marginally feasible at best because of the low transmutation rates, the high volatility, and the corrosiveness of iodine and iodine compounds. It was concluded on the basis of a very conservative repository risk analysis that there are no safety or cost incentives for actinide P-T. In fact, if nonradiological risks are included, the short-term risks of P-T exceed the long-term benefits integrated over a period of 1 million years. Incentives for technetium and iodine P-T exist only if extremely conservative long-term risk analyses are used. Further RD and D in support of P-T is not warranted

A Cost Benefit Analysis of an Accelerator Driven Transmutation System

International Nuclear Information System (INIS)

Westlen, D.; Gudowski, W.; Wallenius, J.; Tucek, K.

2002-01-01

This paper estimates the economical costs and benefits associated with a nuclear waste transmutation strategy. An 800 MWth, fast neutron spectrum, subcritical core design has been used in the study (the so called Sing-Sing Core). Three different fuel cycle scenarios have been compared. The main purpose of the paper has been to identify the cost drivers of a partitioning and transmutation strategy, and to estimate the cost of electricity generated in a nuclear park with operating accelerator driven systems. It has been found that directing all transuranic discharges from spent light water reactor (LWR) uranium oxide (UOX) fuel to accelerator driven systems leads to a cost increase for nuclear power of 50±15%, while introduction of a mixed oxide (MOX) burning step in the LWRs diminishes the cost penalty to 35±10%. (authors)

Hyper fuse: a novel inertial confinement system utilizing hypervelocity projectiles for fusion energy production and fission waste transmutation

International Nuclear Information System (INIS)

Makowitz, H.; Powell, J.R.; Wiswall, R.

1979-01-01

Parametric system studies of an inertial confinement fusion (ICF) reactor system to transmute fission products from an LWR economy have been carried out. The ICF reactors would produce net power in addition to transmuting fission products. The particular ICF concept examined is an impact fusion approach termed HYPERFUSE, in which hypervelocity pellets, traveling on the order of 100 to 300 km/sec, collide with a target in a reactor chamber and initiate a thermonuclear reaction. The DT fusion fuel is contained in a shell of the material to be transmuted, e.g., 137 Cs or 90 Sr. The 14 MeV fusion neutrons released during the pellet burn cause transmutation reactions [e.g., (n, 2n), (n, α), etc.] that convert the long lived fission products (FP's) either to stable products or to species that decay with a short half-life to a stable product

First radiochemical studies on the transmutation of 239Pu with spallation neutrons

International Nuclear Information System (INIS)

Wan, J.-S.; Langrock, E.-J.; Westmeier, W.

2000-01-01

Incineration studies of plutonium were carried out at the synchrophasotron of the Joint Institute for Nuclear Research (Dubna) using proton beams with energies of 0.53 GeV and 1.0 GeV. Solid lead target (8 cm in diameter and 20 cm long) was surrounded with 6 cm thick paraffin as neutron moderator and then irradiated. The transmutation of 239 Pu and the associated production of fission products 91 Sr, 92 Sr, 97 Zr, 99 Mo, 103 Ru, 105 Ru, 129 Sb, 132 Te, 133 I, 135 I and 143 Ce were studied. The plutonium samples (each 449 mg) were placed on the outer surface of moderator. For 1.0 GeV proton beam, the fission rate of 239 Pu is 0.0032 fissions per proton in one gram plutonium samples, for 0.53 GeV proton this value is 0.0022. The experimental uncertainty is about 15%. The experiments are compared to two theoretical model calculations with moderate success, using the Dubna Cascade Model (CEM) and the LAHET code. The practical incineration rate of 239 Pu is very high. For example: if one uses 10mA, 1 GeV proton beams under the same (fictive) experimental conditions, the incineration rate of 239 Pu via fission is 3 mg out of the 449 mg sample per day. For 0.53 GeV protons the corresponding rate is 2 mg per day

Grouping of HLW in partitioning for B/T (burning and/or transmutation) treatment with neutron reactors based on three criteria

International Nuclear Information System (INIS)

Kitamoto, Mulyanto; Kitamoto, Asashi

1995-01-01

A grouping concept of HLW in partitioning for B/T (burning and/or transmutation) treatment by fission reactor was developed in order to improve the disposal in waste management from the safety aspect. The selecting and grouping concept was proposed herein, such as Group MA1 (Np, Am, and unrecovered U and Pu), Group MA2 (Cm, and trace quantity of Cf, etc.), Group A (Tc and I), Group B (Cs and Sr) and Group R (the partitioned remains of HLW), judging from the three criteria for B/T treatment, based on (1) the concept of the potential risk estimated by the hazard index for long-term tendency based on ALI (2) the concept of the relative dose factor related to the adsorbed migration rate transferred through ground water, and (3) the concept of the decay acceleration factor, the burning and/or transmutation characteristics for recycle B/T treatment. (author)

Study of potential of nuclear waste transmutation and safety characteristics of an hybrid system: sub critical accelerator reactor; Etude du potentiel de transmutation et des caracteristiques de surete d`un systeme hybride: accelerateur reacteur sous critique

Energy Technology Data Exchange (ETDEWEB)

Tchistiakov, A

1998-04-01

The study of potential of nuclear waste transmutation for the new reactor systems - hybrid reactors - was the object of this work. Global review of different projects is presented. The basic physical parameters definitions, as neutron surplus and relative importance of external source neutrons, are introduced and explained. For these parameters, numerical values are obtained. The advantage in neutron surplus of fast system is noted. Equilibrium model and corresponding toxicities of different isotopes nd nuclear cycles are presented. Numerical analysis for equilibrium model converge validation are performed also. The study of neutron consumption by `transmutable` Long-Lived Fission Products (Tc, I and Cs) show the possibility of their incineration in dedicated fast hybrid reactors. Equilibrium model shown the influence of reprocessing losses level to cycle toxicity level. Relations between specific fuel inventories (mass normalised by power unit) for thermal and fast spectra are examined. The differences are relatively small. Finally, few hybrid reactor concepts with different objects were analysed. These studies confirm that in frameworks of certain Nuclear Energy scenarios the fast hybrid systems can reduce significantly the radio-toxicity of fuel cycle. Preliminary analyses of sub-critical reactor behaviour show big potential of this reactor type in `Transient of Power` kind of accident, even if more detailed study is necessary. (author)

Neutron spectroscopy at the turn of the century

CERN Document Server

Popov, Yu P

2003-01-01

Neutron spectrometry is a powerful method of investigating atomic nuclei and condensed matter. Such investigations provide necessary data for a very wide spectrum of scientific and technological applications from the fundamental problems of the structure of matter and nucleosynthesis in the Universe to atomic power technologies and the structure of condensed matter. The most frequently utilized is the time-of-flight (TOF) method for powerful pulsed neutron sources. However, in many cases, one can use more effective, simpler and cheaper methods. For example, for astrophysics and radioactive waste transmutation problems, it is sufficient to know an average resonance cross section or "resonance integrals" for capture and fission reactions for neutron spectra specific to neutron fluxes in stars or in the active zone of a transmutation reactor. In these cases, the slow-down neutron spectroscopy (SDNS) methods in lead and graphite moderators will be useful. Compared to the TOF method, the lead SDNS gives a 10/sup 3...

New approach to neutron-induced transmutation, radioactivity and afterheat calculations and its application to fusion reactors

International Nuclear Information System (INIS)

Fukumoto, Hideshi

1986-01-01

A new method and an accompanying computer code CINAC have been developed for the calculation of neutron-induced transmutation, radioactivity and afterheat. In the method, the generation and depletion of nuclides during and after reactor operation are described in a matrix form in which the arrangement of nuclides is determined systematically. The solutions are obtained by an eigenvalue analysis of the matrix without any time steps or iterative schemes which would increase the computational time. The method can treat any type of activation chains equally, and it gives analytical solutions for linear chains. The CINAC code, coupled with the radiation transport codes ANISN and DOT3.5, can also calculate the dose distribution at any time after shutdown in a one- or two-dimensional geometry of fusion reactors. Two calculations were carried out using CINAC to confirm its validity. The results were compared to those calculated by the THIDA code system which is based on a matrix exponential method. The new method was 50 times faster than the latter, while the discrepancy between them was 4 % at the most. (author)

Advanced Reactor Technology Options for Utilization and Transmutation of Actinides in Spent Nuclear Fuel

International Nuclear Information System (INIS)

2009-09-01

-2007). The overall objective of the CRP, performed within the framework of the TWG-FR) was to increase the capability of interested Member States in developing and applying advanced technologies in the area of long lived radioactive waste utilization and transmutation. The final goal of the CRP was to deepen the understanding of the dynamics of transmutation systems, to qualify the available methods, specify their range of validity, and formulate requirements for future theoretical developments. Twenty institutions from 15 Member States and three international organizations have actively participated in this CRP. The comparative investigations cover burner reactors and transmuters both containing fertile and fertile-free fuels. The systems are designed either as neutronically critical or sub-critical (hybrid) driven by an external neutron source. The neutron spectra of the reactors extend from low thermal to fusion neutron energy levels. Further, systems with solid fuels and with molten salt fuels are compared. The solid fuel systems investigated also cover the impact of various coolants from sodium to heavy liquid metals and gas

Status of nuclear transmutation study

International Nuclear Information System (INIS)

Takizuka, Takakazu

1999-01-01

JAERI is carrying out R and Ds on partitioning and transmutation under the OMEGA Program. The R and Ds include the design study of accelerator-driven transmutation systems and the development of transmutation experimental facilities. Accelerator-driven systems have received much interests due to their potential role as dedicated transmuters in the nuclear fuel cycle for minimizing long-lived waste. Principles of accelerator-driven system, its history, JAERI proposed system concepts, and the experimental program are overviewed. (author)

Studies of Accelerator-Driven Systems for Transmutation of Nuclear Waste

International Nuclear Information System (INIS)

Dahlfors, Marcus

2006-01-01

Accelerator-driven systems for transmutation of nuclear waste have been suggested as a means for dealing with spent fuel components that pose potential radiological hazard for long periods of time. While not entirely removing the need for underground waste repositories, this nuclear waste incineration technology provides a viable method for reducing both waste volumes and storage times. Potentially, the time spans could be diminished from hundreds of thousand years to merely 1.000 years or even less. A central aspect for accelerator-driven systems design is the prediction of safety parameters and fuel economy. The simulations performed rely heavily on nuclear data and especially on the precision of the neutron cross section representations of essential nuclides over a wide energy range, from the thermal to the fast energy regime. In combination with a more demanding neutron flux distribution as compared with ordinary light-water reactors, the expanded nuclear data energy regime makes exploration of the cross section sensitivity for simulations of accelerator-driven systems a necessity. This fact was observed throughout the work and a significant portion of the study is devoted to investigations of nuclear data related effects. The computer code package EA-MC, based on 3-D Monte Carlo techniques, is the main computational tool employed for the analyses presented. Directly related to the development of the code is the extensive IAEA ADS Benchmark 3.2, and an account of the results of the benchmark exercises as implemented with EA-MC is given. CERN's Energy Amplifier prototype is studied from the perspectives of neutron source types, nuclear data sensitivity and transmutation. The commissioning of the n T OF experiment, which is a neutron cross section measurement project at CERN, is also described

Exhibit of ADS transmutation system to-Handle MA contained in Highly Radioactive Waste

International Nuclear Information System (INIS)

Marsodi; Lasman, A.N.; Nishihara, K.; Marsongkohadi; Su'ud, Z.

2002-01-01

This ADS transmutation system consists of a high intensity proton beam accelerator, spallation target, and sub-critical reactor core. The general approach was conducted using N-15 fuel to choose a strategy for destroying or minimizing the dangerously radioactive waste using a fast neutron spectrum. The fuel of this system was put surrounding the target with the some composition, i.e. the composition of MOX from PWR reactor spent-fuel with 5 year cooling time. Basic characteristics of this system have been conducted based on analysis of neutronics calculation results using ATRAS codes system

neutron transmutation doping of silicon a thesis submitted to nuclear engineering department for the degree of master of science in nuclear engineering

International Nuclear Information System (INIS)

Abdel Gawwad, M.M.

2003-01-01

When silicon is irradiated by thermal neutrons the objective is to produce a number of phosphorus atoms in the target sample, in order to obtain a given resistivity after treatment. The resistivity of the sample is decreased by the transmutation of the silicon (by neutrons) to phosphorus. After the sample irradiation and decay, the radiochemical cleaning is used to clean the sample. the next step is the sample heat treatment to remove the damage caused by fast neutrons( E> 0.1 MeV). after that, the sample is cut int wafer and polished. The characterization must be carried. out to characterize the specifications of the final product. the present work aims to: find an optimization of the silicon doping processes:sample preparation, for irradiation by cleaning the sample before irradiation to avoid impurity activation. process, by calculating the fluence required to reach the required resistivity. Decay of irradiated sample, it takes four days at least to be handled. handling, it must be carefully to avoid the mechanical damage since the silicon is hard material. etching , to remove the defected layer from the sample . heat treatment , to release the damage caused during irradiation. characterization, to measure the final resistivity and the minority carrier life . hence, calculating the irradiation constant for ETRR-2

Basic plan of partitioning and transmutation technology development

International Nuclear Information System (INIS)

Ikegami, Tetsuo; Ozawa, Masaki

2003-04-01

Basic plan of partitioning and transmutation technology development has been made in more detail and concrete manner in terms of development goal, nuclides to be portioned and to be transmuted, and development schedule, based on the pre-evaluation results of the Research Evaluation Committee on Research and development of partitioning and transmutation technology for long life nuclides' held in August 2000. A step by step approach, consists of three steps, to reach the goal of partitioning and transmutation technology has been adopted under the recognition that the partitioning and transmutation technology development should be progressed steadily as a long term them. The first step is supposed to be able to attain within about 5 years by the present technology and on the extension of it. Such researches as collective separation of TRU, MA/Ln effective separation, and irradiation experiment of iodine and technetium. The second step is such a goal that is expected to be able to realize the engineering feasibility, within about 15 years, through the progress of science technology in future, although the engineering feasibility is not sufficiently foreseen at present. It will need revolutionary technology or breakthrough. Nuclides to be partitioned and to be transmuted have been selected in view points of 'radioactivity and radio-toxicity', 'geological repository', and 'effective utilization', corresponding to the each step of the development goal. Collaboration with other research organizations and with universities in the world should be pursued. Especially, such collaborations with France, with which information exchange on JOYO/PHENIX irradiation experiments is progressing, and with USA, which has recently developed positive activities in this field, are strongly expected. (author)

Estimation of Future Demand for Neutron-Transmutation-Doped Silicon Caused by Development of Hybrid Electric Vehicle

International Nuclear Information System (INIS)

Kim, Myong Seop; Park, Sang Jun

2008-01-01

By using this doping method, silicon semiconductors with an extremely uniform dopant distribution can be produced. They are usually used for high power devices such as thyristor (SCR), IGBT, IGCT and GTO. Now, the demand for high power semiconductor devices has increased rapidly due to the rapid increase of the green energy technologies. Among them, the productions of hybrid cars or fuel cell engines are excessively increased to reduce the amount of discharged air pollution substances, such as carbon dioxide which causes global warming. It is known that the neutron-transmutation-doped floating-zone (FZ) silicon wafers are used in insulated-gate bipolar transistors (IGBTs) which control the speed of the electric traction motors equipped in hybrid or fuel cell vehicles. Therefore, inevitably, it can be supposed that the demand of the NTD silicon is considerably increased. However, it is considered likely that the irradiation capacity will not be large enough to meet the increasing demand. After all, the large irradiation capacity for NTD such as a reactor dedicated to the silicon irradiation will be constructed depending on the industrial demand for NTD silicon. In this work, we investigated the relationship between the hybrid electric vehicle (HEV) industry and the NTD silicon production. Also, we surveyed the prospect for the production of the HEV. Then, we deduced the worldwide demand for the NTD silicon associated with the HEV production. This work can be utilized as the basic material for the construction of the new irradiation facility such as NTD-dedicated neutron source

Transmutation studies with GAMMA-2 setup using relativistic proton beams of the JINR Nuclotron

Czech Academy of Sciences Publication Activity Database

Adam, Jindřich; Balabekyan, AR.; Bradnova, V.; Brandt, R.; Golovatiouk, V. M.; Katovsky, K.; Krivopustov, M. I.; Kalinnikov, V. G.; Odoj, R.; Pronskikh, V. S.; Robotham, H.; Siemon, K.; Solnyshkin, A. A.; Stegailov, V. I.; Tsoupko-Sitnikov, V. M.; Vladimirova, NM.; Westmeier, W.

2006-01-01

Roč. 562, č. 2 (2006), s. 741-742 ISSN 0168-9002 R&D Projects: GA MŠk 1P04LA213 Institutional research plan: CEZ:AV0Z10480505 Keywords : spallation neutron source * transmutation * nuclear waste incineration Subject RIV: BG - Nuclear, Atomic and Molecular Physics, Colliders Impact factor: 1.185, year: 2006

Accelerator technology for Los Alamos nuclear-waste-transmutation and energy-production concepts

International Nuclear Information System (INIS)

Lawrence, G.P.; Jameson, R.A.; Schriber, S.O.

1991-01-01

Powerful proton linacs are being studied at Los Alamos as drivers for high-flux neutron sources that can transmute long-lived fission products and actinides in defense nuclear waste, and also as drivers of advanced fission-energy systems that could generate electric power with no long-term waste legacy. A transmuter fed by an 800-MeV, 140-mA cw conventional copper linac could destroy the accumulated 99 Tc and 129 I at the DOE's Hanford site within 30 years. A high-efficiency 1200-MeV, 140-mA niobium superconducting linac could drive an energy-producing system generating 1-GWe electric power. Preliminary design concepts for these different high-power linacs are discussed, along with the principal technical issues and the status of the technology base. 9 refs., 5 figs., 4 tabs

Transmutation of actinides in power reactors.

Science.gov (United States)

Bergelson, B R; Gerasimov, A S; Tikhomirov, G V

2005-01-01

Power reactors can be used for partial short-term transmutation of radwaste. This transmutation is beneficial in terms of subsequent storage conditions for spent fuel in long-term storage facilities. CANDU-type reactors can transmute the main minor actinides from two or three reactors of the VVER-1000 type. A VVER-1000-type reactor can operate in a self-service mode with transmutation of its own actinides.

Pu Denaturing by Transmutation of MA in FBR Multi-cycle

Energy Technology Data Exchange (ETDEWEB)

Meiliza, Yoshitalia; Saito, Masaki; Sagara, Hiroshi [Tokyo Institute of Technology, 2-12-1-N1-1 Ookayama, Meguro-ku, Tokyo, 1528550 (Japan)

2009-06-15

Pu accumulation and its recycling is important in the term of energy resources, however one of the most sensitive issues is non-proliferation in the future fuel cycle based on fast breeder reactor (FBR). The present paper utilizes Protected Pu Production (P{sup 3}) concept for the production of {sup 238}Pu and {sup 242}Pu by Minor Actinides (MA) transmutation to enhance the proliferation resistance of Pu in the fuel. Increase in the {sup 238}Pu and {sup 242}Pu isotopic fraction creates a high rate of internal heat generation by alpha decay (DH) and/or a high neutron source of spontaneous fission (SFN) in Pu that would be encountered during manufacturing and maintaining of nuclear explosive device. The feasibility of denaturing of Pu by MA transmutation in medium size FBR has been studied from the viewpoint of even-mass number Pu accumulation during multi-cycle of Pu and MA. The proliferation resistance property of Pu is also evaluated based on the specific decay heat and spontaneous fission neutron, compared with the reference criteria. In present paper, the P{sup 3} technology based on multi-recycled Pu and MA is compared with the conventional technology based on multi-recycled Pu only. The detail of mass balance behavior is, however, beyond the scope of the present paper. (authors)

Status of the French research programme for actinides and fission products partitioning and transmutation

International Nuclear Information System (INIS)

Warin, D.

2003-01-01

The paper focus on separation and transmutation research and development programme and main results over these ten last years. The massive research programme on enhanced separation, conducted by CEA and supported by broad international cooperation, has recently achieved some vital progress. Based on real solutions derived from the La Hague process, the CEA demonstrated the lab-scale feasibility of extracting minor actinides and some fission products (I, Cs and Tc) using an hydrometallurgical process that can be extrapolated on the industrial scale. The CEA also conducted programmes proving the technical feasibility of the elimination of minor actinides and fission products by transmutation: fabrication of specific targets and fuels for transmutation tests in the HFR and Phenix reactors, neutronics and technology studies for ADS developments in order to support the MEGAPIE, TRADE and MYRRHA experiments and the future 100 MW international ADS demonstrator. Scenarios studies aimed at stabilizing the inventory with long-lived radionuclides, plutonium, minor actinides and certain long-lived fission products in different nuclear power plant parks and to verify the feasibility at the level of the cycle facilities and fuels involved in those scenarios. Three French Research Groups CEA-CNRS carry out partitioning (PRACTIS) and transmutation (NOMADE and GEDEON) more basic studies. (author)

Neutron Research in HANARO

International Nuclear Information System (INIS)

Kim, Hark Rho

2005-01-01

HANARO (High-flux Advanced Neutron Application Reactor), which was designed and constructed by indigenous technology, is a world-class multi-purpose research reactor with a design thermal power of 30 MW, providing high neutron flux for various applications in Korea. HANARO has been operated since its first criticality in February 1995, and is now successfully utilized in such areas as neutron beam research, fuel and materials tests, radioisotopes and radiopharmaceuticals production, neutron activation analysis, and neutron transmutation doping, etc. A number of experimental facilities have been developed and installed since the beginning of reactor operation, and R and D activities for installing more facilities are actively under progress. Three flux traps in the core (CT, IR1, IR2), providing a high fast neutron flux, can be used for materials and fuel irradiation tests. They are also proper for production of high specific activity radioisotopes. Four vertical holes in the outer core region, abundant in epithermal neutrons, are used for fuel or material tests and radioisotope production. In the heavy water reflector region, 25 vertical holes with high quality thermal neutrons are located for radioisotope production, neutron activation analysis, neutron transmutation doping and cold neutron source installation. The two largest holes named NTD1 and NTD2 are for neutron transmutation doping, CNS for the cold neutron source installation, and LH for the irradiation of large targets. The high resolution powder diffractometer (HRPD) became operational in 1998, followed by the four circle diffractometer (FCD) in 1999, the residual stress instrument (RSI) in 2000, and the small angle neutron spectrometer (SANS) in 2001, respectively. HRPD and SANS became the most popular instruments these days, attracting wide range of users from academia, institutes and industries. We have made a lot of efforts during the last 10 years to develop some key components such as

Set up of an innovative methodology to measure on-line the incineration potential of minor actinides under very high neutron sources in the frame of the future prospects of the nuclear waste transmutation; Mise au point d'une methodologie innovante pour la mesure du potentiel d'incineration d'actinides mineurs sous des sources tres intenses de neutrons, dans la perspective de transmutation des dechets nucleaires

Energy Technology Data Exchange (ETDEWEB)

Fadil, M

2003-03-01

This work deals generally with the problem of nuclear waste management and especially with the transmutation of it to reduce considerably its radiotoxicity potential. The principal objective of this thesis is to show the feasibility to measure on-line the incineration potential of minor actinides irradiated under very high neutron flux. To realize this goal, we have developed fission micro-chambers able to operate, for the first time in the world, in saturation regime under a severe neutron flux. These new chambers use {sup 235}U as an active deposit. They were irradiated in the high flux reactor at Laue-Langevin Institute in Grenoble. The measurement of the saturation current delivered by these chambers during their irradiation for 26 days allowed to evaluate the burn-up of {sup 235}U. We have determined the neutron flux intensity of 1,6 10{sup 15} n.cm{sup -2}.s{sup -1} in the bottom of the irradiation tube called 'V4'. The relative uncertainty of this value is less than 4 %. This is for the first time that such high neutron flux is measured with a fission chamber. To confirm this result, we have also performed independent measurements using gamma spectroscopy of irradiated Nb and Co samples. Both results are in agreement within error bars. Simple Deposit Fission Chambers (SDFC) as above were the reference of the new generation of fission chambers that we have developed in the framework of this thesis: Double Deposit Fission Chambers (DDFC). The reference active deposit was {sup 235}U. The other deposit was the actinide that we wanted to study (e.g. {sup 237}Np and {sup 241}Am). At the end of the thesis, we present some suggestions to ameliorate the operation of the DDFC to be exploited in other transmutation applications in the future. (author)

Program on fuels for transmutation: present status and prospects

Energy Technology Data Exchange (ETDEWEB)

Rouault, J.; Garnier, J.C.; Chauvin, N.; Pillon, S. [CEA Cadarache, 13 - Saint-Paul-lez-Durance (France). Dept. d' Etudes des Combustibles

2001-07-01

The performance calculations of appropriate fuel cycle facilities and reactor configurations (scenarios) relying on current reactor technologies (Pressurized Water Reactor and Fast neutrons Reactors) or innovative reactors (Accelerator Driven Systems) have proved the scientific feasibility of some P and T strategies. To insure the technological feasibility, a large program on fuels and materials is underway, including advanced concepts for PWRs and the development of specific targets (dispersed fuels) for transmutation in Fast Reactors. Experiments in different reactors including Phenix are being prepared. The program is presented and recent results are given. (author)

Program on fuels for transmutation: present status and prospects

International Nuclear Information System (INIS)

Rouault, J.; Garnier, J.C.; Chauvin, N.; Pillon, S.

2001-01-01

The performance calculations of appropriate fuel cycle facilities and reactor configurations (scenarios) relying on current reactor technologies (Pressurized Water Reactor and Fast neutrons Reactors) or innovative reactors (Accelerator Driven Systems) have proved the scientific feasibility of some P and T strategies. To insure the technological feasibility, a large program on fuels and materials is underway, including advanced concepts for PWRs and the development of specific targets (dispersed fuels) for transmutation in Fast Reactors. Experiments in different reactors including Phenix are being prepared. The program is presented and recent results are given. (author)

Development of CERMET fuels for minor actinides transmutation

International Nuclear Information System (INIS)

Haas, D.; Fernandez, A.; Naestren, C.; Staicu, D.; Somers, J.; Maschek, W.; Chen, X.

2006-01-01

The sub-critical Accelerator Driven System (ADS) is now being considered as a potential means to burn long-lived transuranium nuclides. The preferred fuel for such a fast neutron reactor is uranium-free, highly enriched with plutonium and minor actinides. Requirements for ADS transmutation fuels are linked with the core design and safety parameters, the fuel properties and the ease of reprocessing. This study concerns the properties of metals as matrices, with the particular case of Mo. To improve the neutronic characteristics, enriched molybdenum (Mo-92) is required. To overcome the high enrichment cost, it is proposed to recover the matrix by pellet dissolution, and to recycle it for further use. Irradiation programmes are also planned to examine the in-reactor properties of the material. Based on the current status of the research, the results are promising, but irradiation results are still missing. (authors)

Standard Test Method for Measuring Fast-Neutron Reaction Rates by Radioactivation of Niobium

CERN Document Server

American Society for Testing and Materials. Philadelphia

2008-01-01

1.1 This test method describes procedures for measuring reaction rates by the activation reaction 93Nb(n,n′)93mNb. 1.2 This activation reaction is useful for monitoring neutrons with energies above approximately 0.5 MeV and for irradiation times up to about 30 years. 1.3 With suitable techniques, fast-neutron reaction rates for neutrons with energy distribution similar to fission neutrons can be determined in fast-neutron fluences above about 1016cm−2. In the presence of high thermal-neutron fluence rates (>1012cm−2·s−1), the transmutation of 93mNb due to neutron capture should be investigated. In the presence of high-energy neutron spectra such as are associated with fusion and spallation sources, the transmutation of 93mNb by reactions such as (n,2n) may occur and should be investigated. 1.4 Procedures for other fast-neutron monitors are referenced in Practice E 261. 1.5 Fast-neutron fluence rates can be determined from the reaction rates provided that the appropriate cross section information ...

Spallation radiation damage and dosimetry for accelerator transmutation of waste applications

International Nuclear Information System (INIS)

Wechsler, M.S.; Lin, C.

1993-01-01

Proposals are currently being made for systems to treat radioactive waste based on the use of accelerator-driven neutron sources. A linear proton accelerator with energies as high as 1600 MeV and currents up to 250 ma are anticipated for the driver. The neutron fluxes may reach up to 10 20 neutrons/m 2 s as generated by the spallation reactions that occur when the protons strike target materials. Calculations are described to determine radiation fluxes and flux spectra inherent in such systems and to estimate likely radiation effects on system components. The calculations use LAHET, a Monte Carlo high-energy transport code, and MCNP, a generalized-geometry, coupled neutron-photon Monte Carlo transport code. Cross sections for displacement and helium production are presented for spallation neutrons of energies from 21 MeV to 1600 MeV for Inconel 718 (Ni plus 18.5, 18.5, 5.1, and 3 wt % of Cr, Fe, Nb, and Mo, respectively), an alloy that is used for the proton beam entry window in several accelerators. In addition, results for this alloy are presented for the primary knocked-on atom (PKA) spectrum and the transmutation yield for 1600 MeV incident neutrons

Transmutation in ADS and needs for nuclear data, with an introduction to the n-TOF at CERN

CERN Document Server

González, E; Fernández, R; García, J; Villamarín, D

1999-01-01

Transmutation can help in the nuclear waste problem by reducing seriously the life and amount of the most dangerous isotopes (radiotoxicity, heat, packing volume and neutron multiplication reductions). ADS are one of the best technologies for nuclear waste transmutation at large scale. Although enough information is available to prepare conceptual designs and make assessments on their performance, a large R&D campaign is required to obtain the precision data required to optimize the detailed engineering design and refine our expectations calculations on waste reduction by the different transmutation strategies being proposed. In particular a large R&D effort is required in nuclear physics, where fundamental differential measurements and integral verification experiments are required. In this sense, the PS213 n-TOF at CERN PS (at Switzerland) will become one of the largest installations to perform the fundamental differential measurements and a wide international collaboration has been setup to perform...

Electrical property studies of oxygen in Czochralski-grown neutron-transmutation-doped silicon

International Nuclear Information System (INIS)

Cleland, J.W.; Fukuoka, N.

1980-10-01

Electically active oxygen-related donors can be formed in Czochralski (Cz) Si either during crystal growth or during subsequent heat treatment; conventional n- or p-type dopant carrier concentrations are altered if these oxygen donors are present. Neutron transmutation doping (NTD) has been used to introduce a uniform concentration of 31 P in Si. However, oxygen donors can also be formed in NTD Cz Si during the process of annealing to remove NTD radiation damage. In the present experiments, the carrier concentration of Cz and NTD Cz Si samples was determined as a function of the initial dopant, oxygen, and 31 P concentration before and after isothermal or isochronal annealing. It is shown that low temperature (350 to 500 0 C) heat treatment can introduce a significant oxygen donor concentration in Cz Si and in NTD Cz Si that contains radiation-induced lattice defects. Intermediate temperature (550 to 750 0 C) heat treatment, which is intended to remove oxygen donors or lattice defects, can introduce other oxygen donors; annealing above 750 0 C is required to remove any of these oxygen donors. Extended (20 h) high-temperature (1000 to 1200 0 C) annealing can remove oxygen donors and lattice defects, but a significant concentration of oxygen donors can still be introduced by subsequent low temperature heat treatment. These results suggest that oxygen-related donor formation in NTD Cz Si at temperatures below 750 0 C may serve to mask any annealing study of lattice defects. It is concluded that annealing for 30 min at 750 0 C is sufficient to remove radiation damage in NTD Cz Si when the separate effects of oxygen donor formation are included

Evaluation of alternative partitioning/transmutation scenarios using transmutation in light-water reactors (LWRs)

International Nuclear Information System (INIS)

Collins, E.D.; Renier, J.P.; Del Cul, B.; Spencer, B.

2005-01-01

Previous Advanced Fuel Cycle Initiative (AFCI) studies were made to assess the effects of the existing accumulation of LWR spent fuel in the United States on the capability to partition/transmute actinides using existing and advanced LWR. The concept of treating the oldest fuel first indicated that significant advantages could be gained in both partitioning, transmutation, and in overall cost reduction. The processing scenarios previously evaluated assumed that (1) 2000 MT/year of spent fuel, irradiated to 45 GWd/MT and decayed for 30 years is processed; (2) recovered plutonium and 90% of the neptunium are transmuted in LWR MOX fuel; and (3) minor actinides, consisting of americium, curium, and 10% of the neptunium are transmuted in burnable poison type targets. Results of the previous study showed that significant benefits could be obtained, including (1) lower costs for partitioning and transmutation and for storage of spent fuel, (2) maintenance of proliferation resistance for the fissile plutonium in spent fuels, and (3) extended lifetime for the repository. The lower costs would be achieved primarily because no capital investment for a special transmuter reactor (fast reactor, accelerator-driven system, etc.) would be required. Instead, only existing and new LWRs would be utilized. Moreover, no new storage capacity could be needed for spent fuels and irradiated targets because the number of spent fuel assemblies would remain the same after the scenario is begun. Even though the total inventory of plutonium would rise during the early cycles, ∼98% of the plutonium would be contained in stored spent fuel and would be protected by high radiation (the Spent Fuel Standard). This is because the spent fuel would be reprocessed and re-irradiated at intervals within which the fission products, 137 Cs and 90 Sr, both with half-lives of ∼ 30 years, exist in significantly high concentrations.The lifetime of the repository would be extended significantly because all of

Waste transmutation: perspectives

International Nuclear Information System (INIS)

Leray, S.

1997-01-01

After the introduction on the source and nature of nuclear waste, this lecture analyzes the different methods proposed to transmute long-lived isotopes into stable or short-lived isotopes. It is shown that direct methods (photonuclear reactions, spallation, muon catalyzed fusion) do not lead to a sufficient transmutation rate within a reasonable cost. Only the use of hybrid systems, fusion-fission or spallation-fission, can be foreseen. (author)

French fuel cycle strategy and partitioning and transmutation programme

International Nuclear Information System (INIS)

Pradel, Ph.

2007-01-01

The global energy context pleads in favour of a sustainable development of nuclear energy since the demand for energy will likely increase, whereas resources will tend to get scarcer and the prospect of global warming will drive down the consumption of fossil fuel sources. How we deal with radioactive waste is crucial in this context. The production of nuclear energy in France has been associated, since its inception, with the optimisation of radioactive waste management, including the partitioning and the recycling of recoverable energetic materials. The public's concern regarding long-term waste management led the French government to prepare and pass the Law of December 1991, requesting in particular the study for fifteen years of solutions to minimising even further the quantity and the hazardousness of final waste, via partitioning and transmutation. At the end of these fifteen years of research, it is considered that partitioning techniques which have been validated on real solutions are at disposal. Indeed, aqueous process for separation of minor actinides from the PUREX raffinate has been brought to a point where there is reasonable assurance that industrial deployment can be successful. A key experiment has been the kilogram-scale successful trials in the CEA-Marcoule Atalante facility in 2005 and this result, together with the results obtained in the frame of the successive European projects, constitutes a considerable step forward. For transmutation, CEA has conducted programmes proving the feasibility of the elimination of minor actinides and fission products: fabrication of specific targets and fuels for transmutation tests in the HFR and Phenix reactors, neutronics and technology studies for critical reactors and ADS developments. Scenario studies have also allowed assessing the feasibility, at the level of cycle and fuel facilities, and the efficiency of transmutation in terms of the quantitative reduction of the final waste inventory depending of

Status of the French Research on Partitioning and Transmutation

International Nuclear Information System (INIS)

Warin, Dominique

2007-01-01

The global energy context pleads in favor of a sustainable development of nuclear energy since the demand for energy will likely increase, whereas resources will tend to get scarcer and the prospect of global warming will drive down the consumption of fossil fuel sources. How we deal with radioactive waste is crucial in this context. The production of nuclear energy in France has been associated, since its inception, with the optimization of radioactive waste management, including the partitioning and the recycling of recoverable energetic materials. The public's concern regarding the long-term waste management made the French Government prepare and pass the December 1991 Law, requesting in particular, the study for fifteen years of solutions for still minimizing the quantity and the hazardousness of final waste, via partitioning and transmutation. At the end of these fifteen years of research, it is considered that partitioning techniques, which have been validated on real solutions, are at disposal. Indeed, aqueous process for separation of minor actinides from the PUREX raffinate has been brought to a point where there is reasonable assurance that industrial deployment can be successful. A key experiment has been the successful kilogram scale trials in the CEA-Marcoule Atalante facility in 2005 and this result, together with the results obtained in the frame of the successive European projects, constitutes a considerable step forward. For transmutation, CEA has conducted programs proving the feasibility of the elimination of minor actinides and fission products: fabrication of specific targets and fuels for transmutation tests in the HFR and Phenix reactors, neutronics and technology studies for critical reactors and ADS developments. Scenario studies have also allowed assessing the feasibility, at the level of cycle and fuel facilities, and the efficiency of transmutation in terms of the quantitative reduction of the final waste inventory depending of the

Subcritical neutron generator-test facility for nuclear waste transmutation studies

Energy Technology Data Exchange (ETDEWEB)

Chuvilo, I.V.; Kolomiets, A.A.; Kozodaev, A.M. [ITEP, Moscow (Russian Federation)] [and others

1995-10-01

The development of the optimal design of high power facility for NPP transmutation and for a number of applications can not be carried out without preliminary tests of much cheaper prototypes. It has been proposed to combine in new test facility 36 MeV Linac ISTRA constructed in ITEP, original Be target and subcritical blanket that will be mounted on the place of partly disassembled heavy water ITEP experimental reactor. The basic parameters of Linac, schemes of the target and blanket are described. It will provide the direct experiments on installation which can be considered as prototype for future linac driven high power facilities.

TRANSMUTED EXPONENTIATED EXPONENTIAL DISTRIBUTION

OpenAIRE

MEROVCI, FATON

2013-01-01

In this article, we generalize the exponentiated exponential distribution using the quadratic rank transmutation map studied by Shaw etal. [6] to develop a transmuted exponentiated exponential distribution. Theproperties of this distribution are derived and the estimation of the model parameters is discussed. An application to real data set are finally presented forillustration

Transmutation of nuclear waste in accelerator-driven systems

CERN Document Server

Herrera-Martínez, A

2004-01-01

Today more than ever energy is not only a cornerstone of human development, but also a key to the environmental sustainability of economic activity. In this context, the role of nuclear power may be emphasized in the years to come. Nevertheless, the problems of nuclear waste, safety and proliferation still remain to be solved. It is believed that the use of accelerator-driven systems (ADSs) for nuclear waste transmutation and energy production would address these problems in a simple, clean and economically viable, and therefore sustainable, manner. This thesis covers the major nuclear physics aspects of ADSs, in particular the spallation process and the core neutronics specific to this type of systems. The need for accurate nuclear data is described, together with a detailed analysis of the specific isotopes and energy ranges in which this data needs to be improved and the impact of their uncertainty. Preliminary experimental results for some of these isotopes, produced by the Neutron Time-of-Flight (n_TOF) ...

Simulations for the transmutation of nuclear wastes with hybrid reactors

International Nuclear Information System (INIS)

Vuillier, St.

1998-06-01

A Monte Carlo simulation, devoted to the spallation, has been built in the framework of the hybrid systems proposed for the nuclear wastes incineration. This system GSPARTE, described the reactions evolution. It takes into account and improves the nuclear codes and the low and high energy particles transport in the GEANT code environment, adapted to the geometry of the hybrid reactors. Many applications and abacus useful for the wastes transmutation, have been realized with this system: production of thick target neutrons, source definition, material damages. (A.L.B.)

Nuclear waste transmutation and related innovative technologies

International Nuclear Information System (INIS)

2002-01-01

The main topics of the summer school meeting were 1. Motivation and programs for waste transmutation: The scientific perspective roadmaps; 2. The physics and scenarios of transmutation: The physics of transmutation and adapted reactor types. Impact on the fuel cycle and possible scenarios; 3. Accelerator driven systems and components: High intensity accelerators. Spallation targets and experiments. The sub critical core safety and simulation physics experiments; 4. Technologies and materials: Specific issues related to transmutation: Dedicated fuels for transmutation. Fuel processing - the role of pyrochemistry. Materials of irradiation. Lead/lead alloys. 5. Nuclear data: The N-TOF facility. Intermediate energy data and experiments. (orig./GL)

From neutron science project to J-PARC. From the viewpoint of JAERI

International Nuclear Information System (INIS)

Oyama, Yukio

2006-01-01

Japan Atomic Energy Research Institute (JAERI), at present Japan Atomic Energy Agency (JAEA), has been developing particle accelerators since its establishment in 1956 for obtaining basic data on the neutron. Also reactor-based neutron sciences have been developed at JAERI/JAEA. Under the so-called omega project which was started in 1988, JAERI/JAEA has been conducting researches on Engineering Test Accelerator for the nuclear transmutation and has built a Basic Test Accelerator. In 1996, a special team for neutron science promotion was organized and pushed R and D works on proton accelerators, targets, neutron engineering, radiation safety and so on. Integration of proton accelerator projects at JAERI and KEK (Institute for High Energy Physics) was proposed in 1998, and both institutes agreed to establish a unified proton accelerator facility, J-PARC. JAEA is promoting the industrial application of neutrons. Also the research on nuclear transmutation at J-PARC, which is not endorsed yet, is an essential objective for JAEA. (K.Y.)

Reliability assessment of MVP-BURN and JENDL-4.0 related to nuclear transmutation of light platinum group elements

Science.gov (United States)

Terashima, Atsunori; Nilsson, Mikael; Ozawa, Masaki; Chiba, Satoshi

2017-09-01

The Aprés ORIENT research program, as a concept of advanced nuclear fuel cycle, was initiated in FY2011 aiming at creating stable, highly-valuable elements by nuclear transmutation from ↓ssion products. In order to simulate creation of such elements by (n, γ) reaction succeeded by β- decay in reactors, a continuous-energy Monte Carlo burnup calculation code MVP-BURN was employed. Then, it is one of the most important tasks to con↓rm the reliability of MVP-BURN code and evaluated neutron cross section library. In this study, both an experiment of neutron activation analysis in TRIGA Mark I reactor at University of California, Irvine and the corresponding burnup calculation using MVP-BURN code were performed for validation of the simulation on transmutation of light platinum group elements. Especially, some neutron capture reactions such as 102Ru(n, γ)103Ru, 104Ru(n, γ)105Ru, and 108Pd(n, γ)109Pd were dealt with in this study. From a comparison between the calculation (C) and the experiment (E) about 102Ru(n, γ)103Ru, the deviation (C/E-1) was signi↓cantly large. Then, it is strongly suspected that not MVP-BURN code but the neutron capture cross section of 102Ru belonging to JENDL-4.0 used in this simulation have made the big di↑erence as (C/E-1) >20%.

System and safety studies of accelerator driven transmutation. Annual Report 2003

International Nuclear Information System (INIS)

Gudowski, Waclaw; Wallenius, Jan; Tucek, Kamil

2004-12-01

The research on safety of Accelerator-Driven Transmutation Systems (ADS) at the Dept. of Nuclear and Reactor Physics reported here has been focused on different aspects of safety of the Accelerator-Driven Transmutation Systems and on Transmutation research in more general terms. An overview of the topics of our research is given in the Summary which is followed by detailed reports as separate chapters or subchapters. Some of the research topics reported in this report are referred to appendices, which have been published in the open literature. Topics, which are not yet published, are described with more details in the main part of this report. Main focus has been, as before, largely determined by the programme of the European projects of the 5th Framework Programme in which KTH is actively participating. In particular: a) ADS core design and development of advanced nuclear fuel optimised for high transmutation rates and good safety features. This activity includes even computer modeling of nuclear fuel production. Three different ADS-core concept are being investigated: Conceptual design of Pb-Bi cooled core with nitride fuel so called Sing-Sing Core developed at KTH; Pb-Bi cooled core with oxide fuel so called ANSALDO design for the European Project PDS-XADS; Gas cooled core with oxide fuel a design investigated for the European Project PDS-XADS. b) analysis of potential of advance fuels, in particular nitrides with high content of minor actinides; c) analysis of ADS-dynamics and assessment of major reactivity feedbacks; d) emergency heat removal from ADS; e) participation in ADS: MUSE (CEA-Cadarache), YALINA subcritical experiment in Minsk and designing of the subcritical experiment SAD in Dubna; f) theoretical and simulation studies of radiation damage in high neutron (and/or proton) fluxes; g) computer code and nuclear data development relevant for simulation and optimization of ADS, validation of the MCB code and sensitivity analysis; h) studies of

System and safety studies of accelerator driven transmutation. Annual Report 2003

Energy Technology Data Exchange (ETDEWEB)

Gudowski, Waclaw; Wallenius, Jan; Tucek, Kamil [Royal Inst. of Technology, Stockholm (Sweden). Dept. of Nuclear and Reactor Physics] [and others

2004-12-01

The research on safety of Accelerator-Driven Transmutation Systems (ADS) at the Dept. of Nuclear and Reactor Physics reported here has been focused on different aspects of safety of the Accelerator-Driven Transmutation Systems and on Transmutation research in more general terms. An overview of the topics of our research is given in the Summary which is followed by detailed reports as separate chapters or subchapters. Some of the research topics reported in this report are referred to appendices, which have been published in the open literature. Topics, which are not yet published, are described with more details in the main part of this report. Main focus has been, as before, largely determined by the programme of the European projects of the 5th Framework Programme in which KTH is actively participating. In particular: a) ADS core design and development of advanced nuclear fuel optimised for high transmutation rates and good safety features. This activity includes even computer modeling of nuclear fuel production. Three different ADS-core concept are being investigated: Conceptual design of Pb-Bi cooled core with nitride fuel so called Sing-Sing Core developed at KTH; Pb-Bi cooled core with oxide fuel so called ANSALDO design for the European Project PDS-XADS; Gas cooled core with oxide fuel a design investigated for the European Project PDS-XADS. b) analysis of potential of advance fuels, in particular nitrides with high content of minor actinides; c) analysis of ADS-dynamics and assessment of major reactivity feedbacks; d) emergency heat removal from ADS; e) participation in ADS: MUSE (CEA-Cadarache), YALINA subcritical experiment in Minsk and designing of the subcritical experiment SAD in Dubna; f) theoretical and simulation studies of radiation damage in high neutron (and/or proton) fluxes; g) computer code and nuclear data development relevant for simulation and optimization of ADS, validation of the MCB code and sensitivity analysis; h) studies of

A spectral effect on phase evolution in neutron-irradiated aluminum?

International Nuclear Information System (INIS)

Farrell, K.

1994-01-01

It is proposed that the spatial distribution of transmutation-produced silicon precipitates formed in aluminum by capture of thermal neutrons is systematically modified by the fast neutron portion of the spectrum, and the tensile strength is altered accordingly. The concept is used to rationalize some previously erratic tensile data

Maximization of burning and/or transmutation (B/T) capacity in coupled spectrum reactor (CSR) by fuel and core adjustment

International Nuclear Information System (INIS)

Aziz, F.; Kitamoto, Asashi.

1996-01-01

A conceptual design of burning and/or transmutation (B/T) reactor, based on a modified conventional 1150 MWe-PWR system, consisted of two core regions for thermal and fast neutrons, respectively, was proposed herein for the treatments of minor actinides (MA). In the outer region 237 Np, 241 Am, and 243 Am burned by thermal neutrons, while in the inner region 244 Cm was burned mainly by fast neutrons. The geometry of B/T fuel in the outer region was left the same with that of PWR, while in the inner region the B/T fuel was arranged in a tight-lattice geometry that allowed a higher fuel to coolant volume ratio. The maximization of B/T capacity in CSR were done by, first, increasing the radius of the inner region. Second, reducing the coolant to fuel volume ratio, and third, choosing a suitable B/T fuel type. The result of the calculations showed that the equilibrium of main isotopes in CSR can be achieved after about 5 recycle stages. This study also showed that the CSR can burn and transmute up to 808 kg of MA in a single reactor core effectively and safely. (author)

Neutron-induced hydrogen and helium production in iron

Energy Technology Data Exchange (ETDEWEB)

Haight, Robert C.

2004-01-01

In support of the Advanced Fuel Cycle Initiative, cross sections for hydrogen and helium production by neutrons are being investigated on structural materials from threshold to 100 MeV with the continuous-in-energy spallation neutron source at the Los Alamos Neutron Science Center (LANSCE). The present measurements are for elemental iron. The results are compared with values from the ENDF/B-VI library and its extension with LA150 evaluations. For designs in the Advanced Fuel Cycle Initiative, structural materials will be subjected to very large fluences of neutrons, and the selection of these materials will be guided by their resistance to radiation damage. The macroscopic effects of radiation damage result both from displacement of atoms in the materials as well as nuclear transmutation. We are studying the production of hydrogen and helium by neutrons, because these gases can lead to significant changes in materials properties such as embrittlement and swelling. Our experiments span the full range from threshold to 100 MeV. The lower neutron energies are those characteristic of fission neutrons, whereas the higher energies are relevant for accelerator-based irradiation test facilities. Results for the nickel isotopes, {sup 58,60}Ni, have been reported previously. The present studies are on natural iron.

Concept and optimization of burning and transmutation reactor in nuclear fuel recycle system

International Nuclear Information System (INIS)

Marsodi; Mulyanto; Kitamoto, Asashi.

1994-01-01

Basic concept of B/T reactor, not only produces thermal energy but also performs burning and/or transmutation of MA and long-lived FPs, was introduced here based on numerical computation model. The advantage of nuclear reaction by thermal or fast neutron was combined conceptually with each other in order to maximize the overall B/T rate obtained by a composite system of fast and thermal reactor. According to the mass balance analysis of B/T reactors with P-T treatment, fast reactor hardened neutron energy may be effective for MA burning. Furthermore, a high flux reactor operated by fast or thermal neutron could be different from a reactor with high B/T rate or high capacity for loading of MA and/or long-lived FPs. The purpose of this study is to make clear the concept and the performance of fast and thermal B/T reactor designed under high neutron utilization for HLW disposal. (author)

The Impact of Partitioning and Transmutation on the Risk Assesment of a Spent Nuclear Fuel

International Nuclear Information System (INIS)

Amrani, Naima

2006-01-01

Partitioning and transmutation of radioactive and long lived component from the highly radioactive waste stream in order to reduce or probably eliminate their radiotoxic inventory was the important option for the nuclear waste management. The principal radionuclides contribution to the long term radiotoxic inventory is mostly due to Pu, minor actinides and some long-lived fission products. The conditioning operation can present artificial barriers which are potentially capable of confining the radionuclides within their package for thousands of years. After this time nothing can be predicted. The solubility of the actinides (except Np) is generally low whereas the long lived fission product. particularly 137 Cs, 129 I and in some case 99 Tc, display high mobility In the geosphere. Conditioning of separated long-lived nuclides in appropriate matrices which could serve as irradiation matrix in a delayed transmutation option is a possible outcome for the next decades. The general strategy of introducing Partitioning and Transmutation as an additional waste management option is based on the radiological benefit which is expected from such an option. The short term impact of partitioning would be to reduce long-term radiotoxic inventory of the resulting HLW at the expense of an increase of the operational requirements for the nuclear facilities concerned. Fast neutron spectrum devices (FR or ADS facilities) are more efficient than current LWRs for recycling and transmuting long-lived radionuclides

Understanding and predicting the behaviour of silver base neutron absorbers under irradiations

International Nuclear Information System (INIS)

Desgranges, C.

1998-01-01

The effect of neutron irradiation induced transmutations on the swelling of AgInCd (AIC) alloys used as neutron absorber in the control rods of Pressurized Water Reactors has been studied both experimentally and theoretically. Effective atomic volumes have been determined in synthetic AgCdInSn alloys with various compositions and containing fcc and hc phases, representative of irradiated AIC (Sn is a transmutation product). Swelling is shown to result first from the transmutation of Ag into Cd and of In into Sn, both with larger effective volume than the mother atom, and second from grain boundaries precipitation of s still less dense hc phase when solid solubility of transmuted products is exceeded. For both fcc and hc phases, we have determined profiles at the temperatures in the vicinity of the operating temperature. Unusual characteristics of second phase growth at grain boundaries induced by transmutations are identified on a simple binary alloy model: kinetics is controlled by irradiation temperature which scales diffusivities and flux which scales transmutation rates, as well as by the grain size in the underlying matrix. To address the AgInCdSn alloys, a novel technique is proposed to model diffusion in multicomponent alloys. It is based on a linearization of a simple atomistic model. With a single set of parameters, for each phase, our model well reproduces our interdiffusion measurements in quaternary alloys as well as existing interdiffusion experiments in binary alloys. Finally this diffusion model implemented with a moving interface algorithm is used to model the growth of the second phase induced by transmutation in the AIC under irradiation. (authors)

Nuclear data for accelerator-driven transmutation. Annual Report 2001/2002

International Nuclear Information System (INIS)

Blomgren, J.; Johansson, C.; Klug, J.; Olsson, N.; Pomp, S.; Renberg, P.U.

2002-07-01

The present project started 1998-07-01. The primary objective from the supporting organizations is to promote research and research education of relevance for development of the national competence within nuclear energy. The aim of the project is in short to: promote development of the competence within nuclear physics and nuclear technology by supporting licentiate and PhD students; push forward the international research front regarding fundamental nuclear data within the presently highlighted research area 'accelerator-driven transmutation'; strengthen the Swedish in influence within the mentioned research area by expanding the international contact network; constitute a basis for Swedish participation in the nuclear data activities at IAEA and OECD/NEA. The project is run by the Department of Neutron Research (INF)at Uppsala University, and is utilizing the unique neutron beam facility at the national The Svedberg Laboratory (TSL) at Uppsala University. Transmutation techniques in accelerator-driven systems (ADS) involve high-energy neutrons, created in the proton-induced spallation of a heavy target nucleus. The existing nuclear data libraries developed for reactors of today go up to about 20 MeV,which covers all available energies for that application; but with a spallator coupled to a core, neutrons with energies up to 1 - 2 GeV will be present. Although a large majority of the neutrons will be below 20 MeV, the relatively small fraction at higher energies still has to be characterized. Above ∼ 200 MeV, direct reaction models work reasonably well, while at lower energies nuclear distortion plays a non-trivial role. This makes the 20 - 200 MeV region the most important for new experimental cross section data. Very little high-quality neutron-induced data exist in this energy domain.Only the total cross section and the np scattering cross section have been investigated extensively. Besides this, there are data on neutron elastic scattering from UC Davis at

Transmutations for Strings

Directory of Open Access Journals (Sweden)

Amin Boumenir

2008-07-01

Full Text Available We investigate the existence and representation of transmutations, also known as transformation operators, for strings. Using measure theory and functional analytic methods we prove their existence and study their representation. We show that in general they are not close to unity since their representation does not involve a Volterra operator but rather the eigenvalue parameter. We also obtain conditions under which the transmutation is either a bounded or a compact operator. Explicit examples show that they cannot be reduced to Volterra type operators.  

Concept of the demonstration molten salt unit for the transuranium elements transmutation

International Nuclear Information System (INIS)

Alekseev, P.; Dudnikov, A.; Prusakov, V.; Subbotin, S.; Zakirov, R.; Lelek, V.; Peka, I.

1999-01-01

In this report it is considered fluorine reprocessing of spent fuel and fluoride molten salt reactor in critical and subcritical modes for plutonium and minor actinides burning. International collaboration for creation of such system is proposed. It is without any doubt that additional neutron source in the core will have positive influence on the transmutation process in the reactor. On the other side there is a lot of problems to realize it technically and to ensure stable work of the whole complex. (Authors)

Utilization of fast reactor excess neutrons for burning long-lived fission products

International Nuclear Information System (INIS)

Kawashima, K.; Kobayashi, K.; Kaneto, K.

1995-01-01

An evaluation is made on a large MOX fuel fast reactor's capability of burning long lived fission product Tc-99, which dominates the long term radiotoxicity of the high level radioactive waste. The excess neutrons generated in the fast reactor core are utilized to transmute Tc-99 to stable isotopes due to neutron capture reaction. The fission product target assemblies which consist of Tc-99 are charged to the reactor core periphery. The fission product target neutrons are moderated to a great deal to pursue the possibility of enhancing the transmutation rate. Any impacts of loading the fission product target assemblies on the core nuclear performances are assessed. A long term Tc-99 accumulation scenario is considered in the mix of fission product burner fast reactor and non-burner LWRs. (author)

Radioactive waste partitioning and transmutation within advanced fuel cycles: Achievements and Challenges

International Nuclear Information System (INIS)

Salvatores, M.; Palmiotti, G.

2011-01-01

In the last decades, numerous studies have been performed in order to identify appropriate 'Partitioning and Transmutation' (P and T) strategies, aiming to the reduction of the burden on a geological storage (see, among many others, Salvatores, 2005). P and T strategies are very powerful and unique tools to reduce drastically the radiotoxicity level of the wastes and to reduce the time needed to reach the reference level (from ∼100,000 years to few hundred years, i.e. comparable to the period in which technological and engineering means allow reasonably to control the radioactivity confinement). Moreover, P and T allows, in principle, also the reduction of the residual heat in a geological repository, with a potential significant impact on the repository size and characteristics. The first requirement of P and T strategies is the deployment of spent fuel reprocessing techniques (aqueous or dry), which are both in the continuity of today technologies (e.g. as implemented at La Hague in France, where Pu is separated up to 99.9%) or which represent innovative, adapted approaches (e.g. pyrochemistry). The requirement is to extend the performance of Pu separation to 99.9% also to Np, Am and Cm kept together or separated and in any case decontaminated from the lanthanides as much as possible. The separated TRU should then be 'transmuted' (or 'burned') in a neutron field. The essential mechanism is to fission them, transforming them into much shorter lived or stable fission products. However, the fission process is always in competition with other processes, and, in particular, with neutron capture, which does eliminate isotope A, but transforms it into isotope A+1, which can still be radioactive. Isotope A+1 can in turn be fissioned or transmuted into isotope A+2, and so on. The neutron field has to be provided by a fission reactor. The requirement for this (dedicated) reactor is to be able to privilege the fission process with respect to the capture process and to be

Accelerator driven systems (ADS): A principal neutronics and transmutation potential

International Nuclear Information System (INIS)

Slessarev, I.

1997-01-01

An accelerator-based system using a beam of high energy protons to produce supplementary neutrons as a result of spallation processes in a target is investigated. The spallation neutrons are successively used to feed a subcritical blanket where they create a neutron surplus available for incineration of those long-lived toxic nuclei which require neutrons (long-lived fission products and minor actinides), and enhance the deterministic safety features for reactivity-type of accidents

Processing flowsheet for the accelerator transmutation of waste (ATW) program

International Nuclear Information System (INIS)

Dewey, H.; Walker, R.; Yarbro, S.

1992-01-01

At Los Alamos, an innovative approach to transmuting long-lived radioactive waste is under investigation. The concept is to use a linear proton accelerator coupled to a solid target to produce an intense neutron flux. The intense stream of neutrons can then be used to fission or transmute long-lived radionuclides to either stable or shorter-lived isotopes. For the program to be successful, robust chemical separations with high efficiencies (>10 5 ) are required. The actual mission, either defense or commercial, will determine what suite of unit operations will be needed. If the mission is to process commercial spent fuel, there are several options available for feed preparation and blanket processing. The baseline option would be an improved PUREX system with the main alternative being the current ATW actinide blanket processing flowsheet. 99 Tc and 129 I are more likely to reach the biosphere than the actinides. Many models have been developed for predicting how the radionuclides will behave in a repository over long time periods. The general conclusion is that the actinides will be sorbed by the soil. Therefore, over a long time period, e.g., a million years their hazard will be lessened because of radioactive decay and dispersion. However, some of the long-lived fission products are not sorbed and could potentially reach the environment over a few thousand year period. Hence, they could present a significant safety hazard. Because of limited resources, most of the priority has been focused on the actinide and technetium blanket assemblies

Enhancing MA transmutation by irradiation of (MA, Zr)Hx in FBR blanket region - 5383

International Nuclear Information System (INIS)

Konashi, K.; Ikeda, K.; Itoh, K.; Hirai, M.; Koyama, T.; Kurosaki, K.

2015-01-01

Minor actinide (MA) hydride is proposed as transmutation target in sodium-cooled mixed oxide fuelled fast reactor. Preliminarily calculations have been done to check the transmutation efficiency of MA hydride targets. Three different types of MA target, MA-Zr alloy, (MA, Zr)O 2 and (MA, Zr)H x , have been compared on MA transmutation rate. The targets are assumed to be loaded around an active core in a 280 MWe sodium-cooled reactor; 54 MA target assemblies are respectively arranged in a row in the radial blanket zone. They are supposed to be irradiated for one year and then be cooled for 60 days. The transmuted mass has been evaluated by three-dimensional diffusion calculation to be 25, 15, 61 kg/EFPY for the alloy, the oxide and the hydride respectively, where production of MA in the active core is taken into account. The transmutation mass by (MA, Zr)H x is much larger than those by the other types of targets, while the core characteristics remain sound by locating MA targets outside of the active core. On top of that, two kinds of (MA, Zr)O 2 targets which are combined with ZrH x (x=1.7) pins have been calculated. Major Research/Development items are selected to establish the MA hydride transmutation method by reviewing technologies applicable to the transmutation system. The practical use of the MA hydride transmutation method is not far ahead technically, since this method can be developed by the extension of existing technologies. (authors)

The influence of electron irradiation at the various temperatures and annealing on carriers mobility at the low temperatures in neutron transmutation doped gallium arsenide

International Nuclear Information System (INIS)

Korshunov, F.P.; Kurilovich, N.F.; Prokhorenko, T.A.; Troshchinskii, V.T.; Shesholko, V.K.

1999-01-01

The influence of electron irradiation at the various temperatures and annealing on measured at T=100 K carriers mobility in neutron transmutation doped GaAs have been investigated. It was detected that rate of mobility decreasing with irradiation dose increasing decreases when irradiation temperature increases. It was shown that at the same time it take place the radiation defects creating and their particular or full annealing (in the dependence on irradiation temperature). Radiation stimulated annealing (annealing that take place during irradiation at the elevated temperatures) is more effective than the annealing at the same temperatures that take place after crystals are irradiated at room temperature. It means that any defects annealing during irradiation at elevated temperatures take place at more low temperatures than that during annealing after irradiation at room temperature

Study of particle transport in a high power spallation target for an accelerator-driven transmutation system

International Nuclear Information System (INIS)

Shetty, Nikhil Vittal

2013-01-01

AGATE is a project envisaged to demonstrate the feasibility of transmutation in a gas (helium) cooled accelerator-driven system using solid spallation target. Development of the spallation target module and assessing its safety aspects are studied in this work. According to the AGATE concept parameters, 600 MeV protons are delivered on to the segmented tungsten spallation target. The Monte Carlo toolkit Geant4 has been used in the simulation of particle transport. Binary cascade is used to simulate intra-nuclear cascades, along with the G4NDL neutron data library for low energy neutrons (<20 MeV).

Study of particle transport in a high power spallation target for an accelerator-driven transmutation system

Energy Technology Data Exchange (ETDEWEB)

Shetty, Nikhil Vittal

2013-01-31

AGATE is a project envisaged to demonstrate the feasibility of transmutation in a gas (helium) cooled accelerator-driven system using solid spallation target. Development of the spallation target module and assessing its safety aspects are studied in this work. According to the AGATE concept parameters, 600 MeV protons are delivered on to the segmented tungsten spallation target. The Monte Carlo toolkit Geant4 has been used in the simulation of particle transport. Binary cascade is used to simulate intra-nuclear cascades, along with the G4NDL neutron data library for low energy neutrons (<20 MeV).

Use of fast reactors for actinide transmutation. Proceedings of a specialists meeting held in Obninsk, Russian Federation, 22-24 September 1992

Energy Technology Data Exchange (ETDEWEB)

1993-03-15

The management of radioactive waste is one of the key issues in today`s discussions on nuclear energy, especially the long term disposal of high level radioactive wastes. The recycling of plutonium in liquid metal fast breeder reactors (LMFBRs) would allow `burning` of the associated extremely long life transuranic waste, particularly actinides, thus reducing the required isolation time for high level waste from tens of thousands of years to hundreds of years for fission products only. The International Working Group on Fast Reactors (IWGFR) decided to include the topic of actinide transmutation in liquid metal fast breeder reactors in its programme. The IAEA organized the Specialists Meeting on Use of Fast Breeder Reactors for Actinide Transmutation in Obninsk, Russian Federation, from 22 to 24 September 1992. The specialists agree that future progress in solving transmutation problems could be achieved by improvements in: Radiochemical partitioning and extraction of the actinides from the spent fuel (at least 98% for Np and Cm and 99.9% for Pu and Am isotopes); technological research and development on the design, fabrication and irradiation of the minor actinides (MAs) containing fuels; nuclear constants measurement and evaluation (selective cross-sections, fission fragments yields, delayed neutron parameters) especially for MA burners; demonstration of the feasibility of the safe and economic MA burner cores; knowledge of the impact of maximum tolerable amount of rare earths in americium containing fuels. Refs, figs and tabs.

Reliability assessment of MVP-BURN and JENDL-4.0 related to nuclear transmutation of light platinum group elements

Directory of Open Access Journals (Sweden)

Terashima Atsunori

2017-01-01

Full Text Available The Aprés ORIENT research program, as a concept of advanced nuclear fuel cycle, was initiated in FY2011 aiming at creating stable, highly-valuable elements by nuclear transmutation from ↓ssion products. In order to simulate creation of such elements by (n, γ reaction succeeded by β− decay in reactors, a continuous-energy Monte Carlo burnup calculation code MVP-BURN was employed. Then, it is one of the most important tasks to con↓rm the reliability of MVP-BURN code and evaluated neutron cross section library. In this study, both an experiment of neutron activation analysis in TRIGA Mark I reactor at University of California, Irvine and the corresponding burnup calculation using MVP-BURN code were performed for validation of the simulation on transmutation of light platinum group elements. Especially, some neutron capture reactions such as 102Ru(n, γ103Ru, 104Ru(n, γ105Ru, and 108Pd(n, γ109Pd were dealt with in this study. From a comparison between the calculation (C and the experiment (E about 102Ru(n, γ103Ru, the deviation (C/E-1 was signi↓cantly large. Then, it is strongly suspected that not MVP-BURN code but the neutron capture cross section of 102Ru belonging to JENDL-4.0 used in this simulation have made the big di↑erence as (C/E-1 >20%.

Decay and Transmutation of Nuclides

CERN Document Server

Aarnio, Pertti A

1999-01-01

We present a computer code DeTra which solves analytically the Bateman equations governing the decay, build-up and transmutation of radionuclides. The complexity of the chains and the number of nuclides are not limited. The nuclide production terms considered include transmutation of the nuclides inside the chain, external production, and fission. Time dependent calculations are possible since all the production terms can be re-defined for each irradiation step. The number of irradiation steps and output times is unlimited. DeTra is thus able to solve any decay and transmutation problem as long as the nuclear data i.e. decay data and production rates, or cross sections, are known.

Electrical characterization of 10B doped diamond irradiated with low thermal neutron fluence

International Nuclear Information System (INIS)

Reed, M.L.; Reed, M.J.; Jagannadham, K.; Verghese, K.; Bedair, S.M.; El-Masry, N.; Butler, J.E.

2004-01-01

A sample of 10 B isotope doped diamond was neutron irradiated to a thermal fluence of 1.3x10 19 neutron cm -2 . The diamond sample was cooled continuously during irradiation in a nuclear reactor. 7 Li is formed by nuclear transmutation reaction from 10 B. Characterization for electrical conductance in the temperature range of 160 K 10 B doped sample and the 10 B doped and irradiated sample. The unirradiated diamond sample showed p-type conductance at higher temperature (T>200 K) and p-type surface conductance at lower temperature (T 7 Li that is formed by nuclear transmutation reaction from 10 B atoms. Also, compensation of n-type carriers from 7 Li by p-type carriers from 10 B is used to interpret the conductance above 400 K. A low concentration of radiation induced defects, absence of defect complexes, and the low activation energy of n-type 7 Li are thought responsible for the observed variation of conductance in the irradiated diamond. The present results illustrate that neutron transmutation from 10 B doped diamond is a useful method to achieve n-type conductivity in diamond

Transmutation in ADS and Needs for Nuclear Data, with an introduction to the n-TOF at CERN

International Nuclear Information System (INIS)

Gonzalez, E.; Embid, M.; Fernandez, R.; Garcia, J.; Villamarin, D.

1999-01-01

Transmutation can help in the nuclear waste problem by reducing seriously the life and amount of the most dangerous isotopes (radiotoxicity, heat, packing volume and neutron multiplication reductions). ADS are one of the best technologies for nuclear waste transmutation at large scale. Although enough information is available to prepare conceptual designs and make assessments on their performance, a large R and D campaign is required to obtain the precision data required to optimize the detailed engineering design and refine our expectations calculations on waste reduction by the different transmutation strategies being proposed. In particular a large R and D effort is required in nuclear physics, where fundamental differential measurements and integral verification experiments are required. In this sense, the PS213 n-TOF at CERN PS (At Switzerland) will become one of the largest installations to perform the fundamental differential measurements and a wide international collaboration has been setup to perform the cross section measuring campaign. Similarly, the MUSE and several other experiments taking place and in preparation in Europe, USA and Japan will provide the integral verification

Actinide and fission product partitioning and transmutation

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-07-01

The fourth international information exchange meeting on actinide and fission product partitioning and transmutation, took place in Mito City in Japan, on 111-13 September 1996. The proceedings are presented in six sessions: the major programmes and international cooperation, the partitioning and transmutation programs, feasibility studies, particular separation processes, the accelerator driven transmutation, and the chemistry of the fuel cycle. (A.L.B.)

Modern g,d,p,n-induced activation-transmutation systems

International Nuclear Information System (INIS)

Sublet, J.Ch.

2010-01-01

Document available in abstract form only. Full text of publication follows: The European Activation System (EASY) includes as the source of nuclear data the European Activation File (EAF) and as its engine the FISPACT activation-transmutation code. The latest version of the EAF, EAF-2010, contains cross-section data for gamma-, deuteron- and proton-induced reactions in addition to the traditional neutron-induced data. The main reason for the addition of these data to EAF is to enable activation-transmutation calculations to be performed for even more nuclear facilities, including 'accelerator'-driven devices with incident upper energy limit of 60 or 200 MeV. EAF-2010 has benefited from the generation and maintenance of comprehensive activation files in the past and the development of the processing code SAFEPAQ-II and model code TALYS. TALYS is the source for all gamma-, proton- and deuteron-induced data and a fair share of the neutron-induced data. Cross-section validation exercises against both experimental data and systematic, which were started in 1995, enable a comprehensive assessment of the data. Although EAF-2010 is certainly the most-validated activation neutron cross-section library in the world, currently less than 3% of all the reactions can be compared with experimental information, and even then only for a very limited, and not always application-relevant, energy range. As with EAF-2010, -2003, -2005 and -2007 results of integral experiments have been used to correct, adjust and validate data. This can be done using SAFEPAQ II by inputting the measured effective cross-sections. Validation using integral data has been performed by means of direct comparison with measurements of various materials under relevant particle spectra. A tool has recently been developed which is important now that the libraries contain so much TALYS-calculated data. Statistical analysis of cross-sections (SACS) is used to look for trends in the library data for a particular

Transmutations of nuclear waste. Progress report RAS programme 1995: Recycling and transmutation of actinides and fission products

International Nuclear Information System (INIS)

Gruppelaar, H.; Cordfunke, E.H.P.; Konings, R.J.M.; Bultman, J.H.; Dodd, D.H.; Franken, W.M.P.; Kloosterman, J.L.; Koning, A.J.; Wichers, V.A.

1996-04-01

This report describes the progress of the Dutch RAS programme on 'Recycling and Transmutation of Actinides and Fission Products' over the year 1995, which is the second year of the 4-year programme 1994-1997. An extensive listing of reports and publications from 1991 to 1995 is given. Highlights in 1995 were: -The completion of the European Strategy Study on Nuclear Waste Transmutation as a result of which the understanding of transmutation of plutonium, minor actinides and long-lived fission products in thermal and fast reactors has been increased significantly. Important ECN contributions were given on Am, 99 Tc and 129 I transmutation options. Follow-up contracts have been obtained for the study of 100% MOX cores and accelerator-based transmutation. - Important progress in the evaluation of CANDU reactors for burning very large amounts of transuranium mixtures in inert matrices. - The first RAS irradiation experiment in the HFR, in which the transmutation of technetium and iodine was examined, has been completed and post-irradiation examination has been started. - A joint proposal of the EFTTRA cooperation for the 4 th Framework Programme of the EU, to demonstrate the feasibility of the transmutation of americium in an inert matrix by an irradiation in the HFR, has been granted. - A bilateral contract with CEA has been signed to participate in the CAPRA programme, and the work in this field has been started. - The thesis work on Actinide Transmutation in Nuclear Reactor Systems was succesfully defended. New PhD studies on Pu burning in HTGR, on nuclear data for accelerator-based systems, and on the SLM-technique for separation of actinides were started. - A review study of the use of the thorium cycle as a means for nuclear waste reduction, has been completed. A follow-up of this work is embedded in an international project for the 4th Framework Programme of the EU. (orig./DG)

Safety techniques in the change of nuclear systems. Radiation protection at spallation neutron sources and transmutation facilities; Sicherheitstechnik im Wandel Nuklearer Systeme. Strahlenschutz bei Spallationsneutronenquellen und Transmutationsanlagen

Energy Technology Data Exchange (ETDEWEB)

Nuenighoff, Kay

2009-07-01

To push the boundary towards higher neutron fluxes concepts based on spallation reactions have been discussed. Here neutrons are produced by bombarding a heavy metal target (e.g. mercury, tungsten, or tantalum) with high energetic protons. Up to now such facilities could not be realised because of the high power particle accelerators needed. Recent developments of the accelerator technology open the possibility of construction and operating proton accelerators in the MW region. This is demonstrated by construction and commissioning of two MW spallation neutron sources, namely SNS (Oak Ridge, Tennessee, USA) with a power of 1.4 MW and J-PARC (Japan) with 1 MW. The realisation of proton accelerators at this power level will open the way towards energy amplifiers, as proposed e.g. by Carlo Rubbia. Such a facility will not only produce electric power. Furthermore longliving radionuclides can be transmutated into shortlived or even stable nuclides by neutron induced nuclear reactions. A mitigation of the problem of nuclear waste disposal. The above discussed developments prove that accelerators are not only constructed for research, moreover application of these technology became state of the art. With the emergence of particle accelerators in the MW region, radiation protection is confronted with new kind of problems to be solved. Especially the higher kinetic energies of the primary beam particles requires modification and expansion of computer programs well known in nuclear engineering. In contrast to nuclear reactors with kinetic energies up to 2-3 MeV, in spallation reaction secondary particles up to the incident energy in the GeV region will be produced. Problems related to radiation protection have to be considered in an energy range three orders of magnitude higher than known from nuclear reactors. In this thesis existing computer codes are compared and validated with data from selected experiments. Questions concerning radiation protection covers a broad range

Radioanalytical prediction of radiative capture in 99Mo production via transmutation adiabatic resonance crossing by cyclotron

CERN Document Server

Khorshidi, Abdollah; Pazirandeh, Ali; Tenreiro, Claudio; Kadi, Yacine

2014-01-01

In this study, the transmutation adiabatic resonance crossing (TARC) concept was estimated in Mo-99 radioisotope production via radiative capture reaction in two designs. The TARC method was composed of moderating neutrons in lead or a composition of lead and water. Additionally, the target was surrounded by a moderator assembly and a graphite reflector district. Produced neutrons were investigated by (p,xn) interactions with 30 MeV and 300 mu A proton beam on tungsten, beryllium, and tantalum targets. The Mo-99 production yield was related to the moderator property, cross section, and sample positioning inside the distinct region of neutron storage as must be proper to achieve gains. Gathered thermal flux of neutrons can contribute to molybdenum isotope production. Moreover, the sample positioning to gain higher production yield was dependent on a greater flux in the length of thermal neutrons and region materials inside the moderator or reflector. When the sample radial distance from Be was 38 cm inside the...

Real time neutron flux monitoring using Rh self powered neutron detector

Energy Technology Data Exchange (ETDEWEB)

Juna, Byung Jin; Lee, Byung Chul; Park, Sang Jun; Jung, Hoan Sung [KAERI, Daejeon (Korea, Republic of)

2012-10-15

Rhodium (Rh) self powered neutron detectors (SPNDs) are widely used for on line monitoring of local neutron flux. Its signal is slower than the actual variation of neutron flux owing to a delayed {beta} decay of the Rh activation product, but real time monitoring is possible by solving equations between the neutron reaction rate in the detector and its signal. While the measuring system is highly reliable, the accuracy depends on the method solving the equations and accuracy of the parameters in the equations. The uncertain parameters are the contribution of gamma rays to the signal, and the branching ratios of Rh 104 and Rh 104m after the neutron absorption of Rh 103. Real time neutron flux monitoring using Rh SPNDs has been quite successful for neutron transmutation doping (NTD) at HANARO. We revisited the initial data used for the verification of a real time monitoring system, to refine algorithm for a better solution and to check the parameters for correctness. As a result, we suggest an effective way to determine the prompt parameter.

Real time neutron flux monitoring using Rh self powered neutron detector

International Nuclear Information System (INIS)

Juna, Byung Jin; Lee, Byung Chul; Park, Sang Jun; Jung, Hoan Sung

2012-01-01

Rhodium (Rh) self powered neutron detectors (SPNDs) are widely used for on line monitoring of local neutron flux. Its signal is slower than the actual variation of neutron flux owing to a delayed β decay of the Rh activation product, but real time monitoring is possible by solving equations between the neutron reaction rate in the detector and its signal. While the measuring system is highly reliable, the accuracy depends on the method solving the equations and accuracy of the parameters in the equations. The uncertain parameters are the contribution of gamma rays to the signal, and the branching ratios of Rh 104 and Rh 104m after the neutron absorption of Rh 103. Real time neutron flux monitoring using Rh SPNDs has been quite successful for neutron transmutation doping (NTD) at HANARO. We revisited the initial data used for the verification of a real time monitoring system, to refine algorithm for a better solution and to check the parameters for correctness. As a result, we suggest an effective way to determine the prompt parameter

Quality Management for Neutron Transmutation Doping of Silicon Ingot in HANARO

Energy Technology Data Exchange (ETDEWEB)

Kang, Ki-Doo; Kim, Ji-Uk; Yun, Hwa-Kyung; Lim, Chul-Hong; Kim, Young-Chil; Kim, Myong-Seop; Park, Sang-Jun [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2007-10-15

By using this doping method, silicon semiconductors with extremely uniform dopant distributions can be produced, and this is the dominant advantage of NTD compared with a conventional chemical doping. Good uniformity of a dopant concentration is usually required for high power applications such as thyristor (SCR), IGBT, IGCT and GTO and for special sensors. Achieving an accurate neutron fluence corresponding to a target resistivity as well as a uniform irradiation is the prime target of a neutron irradiation for NTD. Generally, in order to reach an accurate neutron fluence, a real time neutron flux is monitored by a neutron detector such as a Self-powered Neutron Detector(SPND). And, after an irradiation, the total irradiation fluence is confirmed by measuring the absolute activity of a neutron activation sample that has been irradiated with a silicon ingot, and thus the SPND can be properly calibrated. Excellent irradiation uniformity and a high accuracy for a target neutron dose have been achieved from the early works of NTD. However, to maintain this excellent quality, the neutron irradiation fluence should be continuously modified and controlled. So, in this work, an activity to maintain the irradiation quality is introduced.

Physical Investigation for Neutron Consumption and Multiplication in Blanket Module of Fusion-Fission Hybrid Reactor

International Nuclear Information System (INIS)

Tariq Siddique, M.; Kim, Myung Hyun

2014-01-01

Fusion-fission hybrid reactor can be the first milestone of fusion technology and achievable in near future. It can provide operational experience for tritium recycling for pure fusion reactor and be used for incineration of high-level long-lived waste isotopes from existing fission power reactors. Hybrid reactor for waste transmutation (Hyb-WT) was designed and optimized to assess its otential for waste transmutation. ITER will be the first large scaled experimental tokamak facility for the testing of test blanket modules (TBM) which will layout the foundation for DEMO fusion power plants. Similarly hybrid test blanket module (HTBM) will be the foundation for rationality of fusion fission hybrid reactors. Designing and testing of hybrid blankets will lead to another prospect of nuclear technology. This study is initiated with a preliminary design concept of a hybrid test blanket module (HTBM) which would be tested in ITER. The neutrons generated in D-T fusion plasma are of high energy, 14.1 MeV which could be multiplied significantly through inelastic scattering along with fission in HTBM. In current study the detailed neutronic analysis is performed for the blanket module which involves the neutron growth and loss distribution within blanket module with the choice of different fuel and coolant materials. TRU transmutation and tritium breeding performance of HTBM is analyzed under ITER irradiation environment for five different fuel types and with Li and LiPb coolants. Simple box geometry with plate type TRU fuel is adopted so that it can be modelled with heterogeneous material geometry in MCNPX. Waste transmutation ratio (WTR) of TRUs and tritium breeding ration (TBR) is computed to quantify the HTBM performance. Neutron balance is computed in detail to analyze the performance parameters of HTBM. Neutron spectrum and fission to capture ratio in TRU fuel types is also calculated for detailed analysis of HTBM

Physical Investigation for Neutron Consumption and Multiplication in Blanket Module of Fusion-Fission Hybrid Reactor

Energy Technology Data Exchange (ETDEWEB)

Tariq Siddique, M.; Kim, Myung Hyun [Kyung Hee Univ., Yongin (Korea, Republic of)

2014-05-15

Fusion-fission hybrid reactor can be the first milestone of fusion technology and achievable in near future. It can provide operational experience for tritium recycling for pure fusion reactor and be used for incineration of high-level long-lived waste isotopes from existing fission power reactors. Hybrid reactor for waste transmutation (Hyb-WT) was designed and optimized to assess its otential for waste transmutation. ITER will be the first large scaled experimental tokamak facility for the testing of test blanket modules (TBM) which will layout the foundation for DEMO fusion power plants. Similarly hybrid test blanket module (HTBM) will be the foundation for rationality of fusion fission hybrid reactors. Designing and testing of hybrid blankets will lead to another prospect of nuclear technology. This study is initiated with a preliminary design concept of a hybrid test blanket module (HTBM) which would be tested in ITER. The neutrons generated in D-T fusion plasma are of high energy, 14.1 MeV which could be multiplied significantly through inelastic scattering along with fission in HTBM. In current study the detailed neutronic analysis is performed for the blanket module which involves the neutron growth and loss distribution within blanket module with the choice of different fuel and coolant materials. TRU transmutation and tritium breeding performance of HTBM is analyzed under ITER irradiation environment for five different fuel types and with Li and LiPb coolants. Simple box geometry with plate type TRU fuel is adopted so that it can be modelled with heterogeneous material geometry in MCNPX. Waste transmutation ratio (WTR) of TRUs and tritium breeding ration (TBR) is computed to quantify the HTBM performance. Neutron balance is computed in detail to analyze the performance parameters of HTBM. Neutron spectrum and fission to capture ratio in TRU fuel types is also calculated for detailed analysis of HTBM.

Transmutation of 129I Using an Accelerator-Driven System

International Nuclear Information System (INIS)

Nishihara, Kenji; Takano, Hideki

2002-01-01

A conceptual blanket design for 129 I transmutation is proposed for an accelerator-driven system (ADS) that is designed to transmute minor actinides (MAs). In this ADS, 250 kg/yr of MA and 56 kg/yr of iodine are simultaneously transmuted, and they correspond to the quantities generated from ∼10 units of existing light water reactors. Furthermore, an introduction scenario and the benefit of iodine transmutation are studied for future introduction of fast breeder reactors. It is shown that the transmutation of iodine benefits the concept of underground disposal

Engineering design of a neutron generator

Energy Technology Data Exchange (ETDEWEB)

Coelho, Daniel M.; Campos, Tarcísio P.R. de, E-mail: dmcoelho.eng@gmail.com, E-mail: tprcampos@pq.cnpq.br [Universidade Federal de Minas Gerais (NRI/UFMG), Belo Horizonte, MG (Brazil). Departamento de Engenharia Nuclear. Nucleo de Radiações Ionizantes

2017-07-01

This paper presents an engineering design of a neutron generator (NG). In order to analyze and choose the materials and the appropriate geometry, previous studies of NRI Group (Nucleus for Ionizing Radiation at UFMG - NRI/UFMG) were considered and a model was developed for the simulation of these systems. The efficiency of a neutron generator is measured by the neutron flux. Among the modeling and simulation methods, was employed open software sources for the transmuting cell, aiming to evaluate resonant cavity and for complementary physical analysis. In addition, the titanium target was compared designed based in other studies of NRI Group. Deuterium plasma with a density close to 10{sup 10} particles/cm³, was proposed with a frequency of 0.898 GHz and an approximate wavelength of 110 μm, using a radio frequency antenna up to 2.45 GHz. This compact system includes a hydrogen-isotopes fusor, moderator, reflector and shield. Neutron reflection minimized the neutron escape, increasing the final flux. A insulation material is required to enclose the device. As a conclusion, the investigated nuclear and electromagnetic features of NG have demonstrated that such generator shall have a notable potential for radioisotope generation applied to medical diagnosis. The designs presented will be used to build a 3D model in the NRI laboratory and then a prototype with the selected materials. (author)

Fuel cycle of fast reactor Brest with non-proliferation, transmutation of long-lived nuclides and equivalent disposal of radioactive waste

International Nuclear Information System (INIS)

Lopatkin, A.V.; Orlov, V.V.

2001-01-01

The declared objectives in the fuel cycle of fast reactor BREST achieved by the following measures. Proliferation resistance of the fuel cycle being developed for BREST reactors is provided along two lines: reactors physics and design features; spent fuel reprocessing technology excluding plutonium separation at all process stages. Surplus neutrons produced in a chain reaction in a fast reactor without uranium blanket and the high flux of fast neutrons, allow efficient transmutation of not only all actinides in the core but also long-lived fission products (I, Te) in lead blanket by leakage neutrons without detriment to the inherent safety of this reactor. (author)

Neutronic Parametric Study on a Conceptual Design for a Transmutation Fusion Blanket

International Nuclear Information System (INIS)

Tariq Siddique, M.; Kim, Myung Hyun

2011-01-01

Fusion energy may be the one of options of future energy. In all over the world, researchers are putting their efforts for its commercial and economical availability. Fusion-fission hybrid reactors have been studied for various applications in China. First milestone of fusion energy is expected to be the fusion fission hybrid reactors. In fusion-fission hybrid reactor the blanket design is of second prime importance after fusion source. In this study conceptual design of a fusion blanket is initiated for calculation of tritium production, transmutation of minor actinides (MA) and fission products (FP) and energy multiplication calculations

Transmutation of long-lived fission products

International Nuclear Information System (INIS)

Abrahams, K.

1994-01-01

The time-accumulated dose related to technetium dominates the leakage doses in most scenarios for imperturbed geological disposal. If human intrusion into geologically stable repositories or other disturbances is taken into account, the actinides determine the maximum value of the expected individual dose rates of shorter storage times. Therefore actinides dominate the discussion on transmutation of nuclear waste. In principle current LWRs could be used for a massive transmutation of Tc and perhaps I. Fast reactors and HWRs have attractive potential with respect to transmutation in moderated assemblies. HWRs like CANDU have easy refuelling possibilities. (orig.)

Shubnikov-de Haas effect study of InAs after transmutation doping at low temperatures

International Nuclear Information System (INIS)

Gerstenberg, H.; Mueller, P.

1990-01-01

Degenerate InAs single crystals have been irradiated by thermal neutrons below 6 K. The Shubnikov-de Haas effect and the electrical resistivity have been measured as a function of the neutron dose and the annealing temperature. The effects of transmutation doping and simultaneous introduction of lattice defects have been analysed in terms of the conduction electron density and the scattering rates τ ρ -1 - ρne 2 /m * and τ x -1 2πkub(B)X/h/2π (where X is the Dingle temperature). The measured conduction electron density after irradiation and thermal annealing agreed well with the values calculated from the experimental and materials parameters. The effects of radiation damage may qualitatively be explained assuming neutral In vacancies to be the most common type of defect in thermal-neutron-irradiated InAs. A comparison with similar experiments on InSb is given. (author)

Effects of silicon cross section and neutron spectrum on the radial uniformity in neutron transmutation doping

International Nuclear Information System (INIS)

Kim, Haksung; Ho Pyeon, Cheol; Lim, Jae-Yong; Misawa, Tsuyoshi

2012-01-01

The effects of silicon cross section and neutron spectrum on the radial uniformity of a Si-ingot are examined experimentally with various neutron spectrum conditions. For the cross section effect, the numerical results using silicon single crystal cross section reveal good agreements with experiments within relative difference of 6%, whereas the discrepancy is approximately 20% in free-gas cross section. For the neutron spectrum effect, the radial uniformity in hard neutron spectrum is found to be more flattening than that in soft spectrum. - Highlights: ► The effects of silicon cross section and neutron spectrum on the radial uniformity in NTD were experimentally investigated. ► The numerical results using silicon single crystal cross section reveal good agreements. ► The radial uniformity in hard neutron spectrum was more flat than that in soft spectrum. ► The silicon single crystal cross section and hard neutron spectrum are recommended for numerical analyses and radial uniformity flattening in NTD, respectively.

Neutron cross sections for fusion

International Nuclear Information System (INIS)

Haight, R.C.

1979-10-01

First generation fusion reactors will most likely be based on the 3 H(d,n) 4 He reaction, which produces 14-MeV neutrons. In these reactors, both the number of neutrons and the average neutron energy will be significantly higher than for fission reactors of the same power. Accurate neutron cross section data are therefore of great importance. They are needed in present conceptual designs to calculate neutron transport, energy deposition, nuclear transmutation including tritium breeding and activation, and radiation damage. They are also needed for the interpretation of radiation damage experiments, some of which use neutrons up to 40 MeV. In addition, certain diagnostic measurements of plasma experiments require nuclear cross sections. The quality of currently available data for these applications will be reviewed and current experimental programs will be outlined. The utility of nuclear models to provide these data also will be discussed. 65 references

Transmutation of Tc-99 in fission reactors

International Nuclear Information System (INIS)

Kloosterman, J.L.; Li, J.M.

1994-12-01

Transmutation of Tc-99 in three different types of fission reactors is considered: A heavy water reactor, a fast reactor and a light water reactor. For the first type a CANDU reactor was chosen, for the second one the Superphenix reactor, and for the third one a PWR. The three most promising Tc-99 transmuters are the fast reactor with a moderated subassembly in the inner core, a fast reactor with a non-moderated subassembly in the inner core, and a heavy water reactor with Tc-99 target pins in the moderator between the fuel bundles. Transmutation half lives of 15 to 25 years can be achieved, with yearly transmuted Tc-99 masses of about 100 kg at a thermal reactor power of about 3000 MW. (orig.)

Modelling of an experiment for the study of neutron spallation source at JINR

International Nuclear Information System (INIS)

Kumawat, Harphool; Goyal, Uttam; Kumar, V.; Barashenkov, V.S.

2002-01-01

Intense neutron spallation source (INSS) is a necessary requirement of accelerator driven sub-critical systems. INSS are proposed to be generated using the high current proton beams. Some studies are conducted for the neutron flux, transmutation rates and energy gains and a larger number of related experiments are being planned

Transmutation of minor actinide using thorium fueled BWR core

International Nuclear Information System (INIS)

Susilo, Jati

2002-01-01

One of the methods to conduct transmutation of minor actinide is the use of BWR with thorium fuel. Thorium fuel has a specific behaviour of producing a little secondary minor actinides. Transmutation of minor actinide is done by loading it in the BWR with thorium fuel through two methods, namely close recycle and accumulation recycle. The calculation of minor actinide composition produced, weigh of minor actinide transmuted, and percentage of reminder transmutation was carried SRAC. The calculations were done to equivalent cell modeling from one fuel rod of BWR. The results show that minor actinide transmutation is more effective using thorium fuel than uranium fuel, through both close recycle and accumulation recycle. Minor actinide transmutation weight show that the same value for those recycle for 5th recycle. And most of all minor actinide produced from 5 unit BWR uranium fuel can transmuted in the 6 t h of close recycle. And, the minimal value of excess reactivity of the core is 12,15 % Δk/k, that is possible value for core operation

Transmuted Generalized Inverse Weibull Distribution

OpenAIRE

Merovci, Faton; Elbatal, Ibrahim; Ahmed, Alaa

2013-01-01

A generalization of the generalized inverse Weibull distribution so-called transmuted generalized inverse Weibull dis- tribution is proposed and studied. We will use the quadratic rank transmutation map (QRTM) in order to generate a flexible family of probability distributions taking generalized inverse Weibull distribution as the base value distribution by introducing a new parameter that would offer more distributional flexibility. Various structural properties including explicit expression...

Design of a target and moderator at the Los Alamos Spallation Radiation Effects Facility (LASREF) as a neutron source for fusion reactor materials development

International Nuclear Information System (INIS)

Ferguson, P.D.; Mueller, G.E.

1993-01-01

The LASREF facility is located in the beam stop area at LAMPF. The neutron spectrum is fission-like with the addition of a 3% to 5% component with E > 20 MeV. The present study evaluates the limits on geometry and material selection that will maximize the neutron flux. MCNP and LAHET were used to predict the neutron flux and energy spectrum for a variety of geometries. The problem considers 760 MeV protons incident on tungsten. The resulting neutrons are multiplied in uranium through (n,xn) reactions. Calculations show that a neutron flux greater than 10 19 n/m 2 /s is achievable. The helium to dpa ratio and the transmutation product generation are calculated. These results are compared to expectations for the proposed DEMO fusion reactor and to FFTF

Target fuels for plutonium and minor actinide transmutation in pressurized water reactors

International Nuclear Information System (INIS)

Washington, J.; King, J.; Shayer, Z.

2017-01-01

Highlights: • We evaluate transmutation fuels for plutonium and minor actinide destruction in LWRs. • We model a modified AP1000 fuel assembly in SCALE6.1. • We evaluate spectral shift absorber coatings to improve transmutation performance. - Abstract: The average nuclear power plant produces twenty metric tons of used nuclear fuel per year, containing approximately 95 wt% uranium, 1 wt% plutonium, and 4 wt% fission products and transuranic elements. Fast reactors are a preferred option for the transmutation of plutonium and minor actinides; however, an optimistic deployment time of at least 20 years indicates a need for a nearer-term solution. This study considers a method for plutonium and minor actinide transmutation in existing light water reactors and evaluates a variety of transmutation fuels to provide a common basis for comparison and to determine if any single target fuel provides superior transmutation properties. A model developed using the NEWT module in the SCALE 6.1 code package provided performance data for the burnup of the target fuel rods in the present study. The target fuels (MOX, PuO_2, Pu_3Si_2, PuN, PuUZrH, PuZrH, PuZrHTh, and PuZrO_2) are evaluated over a 1400 Effective Full Power Days (EFPD) interval to ensure each assembly remained critical over the entire burnup period. The MOX (5 wt% PuO_2), Pu_0_._3_1ZrH_1_._6Th_1_._0_8, and PuZrO_2MgO (8 wt% Pu) fuels result in the highest rate of plutonium transmutation with the lowest rate of curium-244 production. This study selected eleven different burnable absorbers (B_4C, CdO, Dy_2O_3, Er_2O_3, Eu_2O_3, Gd_2O_3, HfO_2, In_2O_3, Lu_2O_3, Sm_2O_3, and TaC) for evaluation as spectral shift absorber coatings on the outside of the fuel pellets to determine if an absorber coating can improve the transmutation properties of the target fuels. The PuZrO_2MgO (8 wt% Pu) target fuel with a coating of Lu_2O_3 resulted in the highest rate of plutonium transmutation with the greatest reduction in curium

Target fuels for plutonium and minor actinide transmutation in pressurized water reactors

Energy Technology Data Exchange (ETDEWEB)

Washington, J., E-mail: jwashing@gmail.com [Nuclear Science and Engineering Program, Colorado School of Mines, 1500 Illinois St., Golden, CO 80401 (United States); King, J., E-mail: kingjc@mines.edu [Nuclear Science and Engineering Program, Colorado School of Mines, 1500 Illinois St., Golden, CO 80401 (United States); Shayer, Z., E-mail: zshayer@mines.edu [Department of Physics, Colorado School of Mines, 1500 Illinois St., Golden, CO 80401 (United States)

2017-03-15

Highlights: • We evaluate transmutation fuels for plutonium and minor actinide destruction in LWRs. • We model a modified AP1000 fuel assembly in SCALE6.1. • We evaluate spectral shift absorber coatings to improve transmutation performance. - Abstract: The average nuclear power plant produces twenty metric tons of used nuclear fuel per year, containing approximately 95 wt% uranium, 1 wt% plutonium, and 4 wt% fission products and transuranic elements. Fast reactors are a preferred option for the transmutation of plutonium and minor actinides; however, an optimistic deployment time of at least 20 years indicates a need for a nearer-term solution. This study considers a method for plutonium and minor actinide transmutation in existing light water reactors and evaluates a variety of transmutation fuels to provide a common basis for comparison and to determine if any single target fuel provides superior transmutation properties. A model developed using the NEWT module in the SCALE 6.1 code package provided performance data for the burnup of the target fuel rods in the present study. The target fuels (MOX, PuO{sub 2}, Pu{sub 3}Si{sub 2}, PuN, PuUZrH, PuZrH, PuZrHTh, and PuZrO{sub 2}) are evaluated over a 1400 Effective Full Power Days (EFPD) interval to ensure each assembly remained critical over the entire burnup period. The MOX (5 wt% PuO{sub 2}), Pu{sub 0.31}ZrH{sub 1.6}Th{sub 1.08}, and PuZrO{sub 2}MgO (8 wt% Pu) fuels result in the highest rate of plutonium transmutation with the lowest rate of curium-244 production. This study selected eleven different burnable absorbers (B{sub 4}C, CdO, Dy{sub 2}O{sub 3}, Er{sub 2}O{sub 3}, Eu{sub 2}O{sub 3}, Gd{sub 2}O{sub 3}, HfO{sub 2}, In{sub 2}O{sub 3}, Lu{sub 2}O{sub 3}, Sm{sub 2}O{sub 3}, and TaC) for evaluation as spectral shift absorber coatings on the outside of the fuel pellets to determine if an absorber coating can improve the transmutation properties of the target fuels. The PuZrO{sub 2}MgO (8 wt% Pu) target

Study on multi-recycle transmutation of LLFP in light water reactor

International Nuclear Information System (INIS)

Setiawan, M.B.; Kitamoto, A.

2001-01-01

The effectiveness of transmutation for long-lived fission products (LLFP) in light water reactors (LWR), i.e. both BWR and PWR, considering the large capture cross-section of FPs in thermal region was evaluated. Calculation results of iodine and technetium transmutation in BWR and PWR suggested an effective use of BWR as compared to PWR. To obtain transmutation fraction [TF] of 30 to 40%, the irradiation period needed for 99 Tc transmutation was estimated as 10 to 15 years, and the period for 129 I transmutation was estimated as 30 to 40 years, respectively. The evaluations bring a new concept of multi-recycle LLFP transmutation using LWR TR (LWR for transmutation)

Optimisation of composite metallic fuel for minor actinide transmutation in an accelerator-driven system

Science.gov (United States)

Uyttenhove, W.; Sobolev, V.; Maschek, W.

2011-09-01

A potential option for neutralization of minor actinides (MA) accumulated in spent nuclear fuel of light water reactors (LWRs) is their transmutation in dedicated accelerator-driven systems (ADS). A promising fuel candidate dedicated to MA transmutation is a CERMET composite with Mo metal matrix and (Pu, Np, Am, Cm)O 2-x fuel particles. Results of optimisation studies of the CERMET fuel targeting to increasing the MA transmutation efficiency of the EFIT (European Facility for Industrial Transmutation) core are presented. In the adopted strategy of MA burning the plutonium (Pu) balance of the core is minimized, allowing a reduction in the reactivity swing and the peak power form-factor deviation and an extension of the cycle duration. The MA/Pu ratio is used as a variable for the fuel optimisation studies. The efficiency of MA transmutation is close to the foreseen theoretical value of 42 kg TW -1 h -1 when level of Pu in the actinide mixture is about 40 wt.%. The obtained results are compared with the reference case of the EFIT core loaded with the composite CERCER fuel, where fuel particles are incorporated in a ceramic magnesia matrix. The results of this study offer additional information for the EFIT fuel selection.

Optimisation of composite metallic fuel for minor actinide transmutation in an accelerator-driven system

International Nuclear Information System (INIS)

Uyttenhove, W.; Sobolev, V.; Maschek, W.

2011-01-01

A potential option for neutralization of minor actinides (MA) accumulated in spent nuclear fuel of light water reactors (LWRs) is their transmutation in dedicated accelerator-driven systems (ADS). A promising fuel candidate dedicated to MA transmutation is a CERMET composite with Mo metal matrix and (Pu, Np, Am, Cm)O 2-x fuel particles. Results of optimisation studies of the CERMET fuel targeting to increasing the MA transmutation efficiency of the EFIT (European Facility for Industrial Transmutation) core are presented. In the adopted strategy of MA burning the plutonium (Pu) balance of the core is minimized, allowing a reduction in the reactivity swing and the peak power form-factor deviation and an extension of the cycle duration. The MA/Pu ratio is used as a variable for the fuel optimisation studies. The efficiency of MA transmutation is close to the foreseen theoretical value of 42 kg TW -1 h -1 when level of Pu in the actinide mixture is about 40 wt.%. The obtained results are compared with the reference case of the EFIT core loaded with the composite CERCER fuel, where fuel particles are incorporated in a ceramic magnesia matrix. The results of this study offer additional information for the EFIT fuel selection.

Actinide and Fission Product Partitioning and Transmutation

International Nuclear Information System (INIS)

2015-06-01

The benefits of partitioning and transmutation (P and T) have now been established worldwide and, as a result, many countries are pursuing R and D programmes to advance the technologies associated with P and T. In this context, the OECD Nuclear Energy Agency (NEA) has organised a series of biennial information exchange meetings to provide experts with a forum to present and discuss state-of-the-art developments in the field of partitioning and transmutation since 1990. The OECD Nuclear Energy Agency Information Exchange Meeting on Actinides and Fission Products Partitioning and Transmutation is a forum for experts to present and discuss the state-of-the-art development in the field of P and T. Thirteen meetings have been organised so far and held in Japan, the United States, France, Belgium, Spain, the Republic of Korea and the Czech Republic. This 13. meeting was hosted by Seoul National University (Seoul, Republic of Korea) and was organised in co-operation with the International Atomic Energy Agency (IAEA) and the European Community (EC). The meeting covered strategic and scientific developments in the field of P and T such as: fuel cycle strategies and transition scenarios, the role of P and T in the potential evolution of nuclear energy as part of the future energy mix; radioactive waste management strategies; transmutation fuels and targets; advances in pyro and aqueous separation processes; P and T specific technology requirements (materials, spallation targets, coolants, etc.); transmutation systems: design, performance and safety; impact of P and T on the fuel cycle; fabrication, handling and transportation of transmutation fuels. A total of 103 presentations (39 oral and 64 posters) were discussed among the 110 participants from 19 countries and 2 international organisations. The meeting consisted of one plenary session where national and international programmes were presented followed by 5 technical sessions: - Fuel Cycle Strategies and Transition

The sphinx project: experimental verification of design inputs for a transmuter with liquid fuel based on molten fluorides

International Nuclear Information System (INIS)

Hron, M.; Uhlir, J.; Vanicek, J.

2002-01-01

The current proposals for high-active long-lived (more then 10 4 years) waste from spent nuclear fuel disposal calls forth an increasing societal mistrust towards nuclear power. These problems are highly topical in the Czech Republic, a country which is operating nuclear power and accumulating spent fuel from PWRs and is further located on an inland and heavily populous Central European region. The proposed project, known under the acronym SPHINX (SPent Hot fuel Incineration by Neutron flux) deals with a solution to some of the principle problems through a very promising means of radioactive waste treatment. In particular, high-level wastes from spent nuclear fuel could be treated using this method, which is based on the transmutation of radionuclides through the use of a nuclear reactor with liquid fuel based on molten fluorides (Molten Salt Transmutation Reactor - MSTR) which might be a subcritical system driven by a suitable neutron source. Its superiority also lies in the fact that it makes possible to utilize actinides contained, by others, in spent nuclear fuel and so to reach a positive energy effect. After the first three-year stage of Research and Development which has been focused mostly on computer analyses of neutronics and corresponding physical characteristics, the next three-year stage of this programme will be devoted to experimental verification of inputs for the design of a demonstration transmuter using molten fluoride fuel. The Research and Development part of the SPHINX project in the area of fuel cycle of the MSTR is focused in the first place on the development of suitable technology for the preparation of an introductory liquid fluoride fuel for MSTR and subsequently on the development of suitable fluoride pyrometallurgical technology for the separation of the transmuted elements from the non-transmuted ones. The idea of the introductory fuel preparation is based on the reprocessing of PWR spent fuel using the Fluoride Volatility Method

Development of nuclear transmutation technology for transuranic elements

International Nuclear Information System (INIS)

Mukaiyama, Takehiko

1996-01-01

Partitioning and Transmutation (P-T) of long-lived radioactive nuclides is conceived as the technology to improve the high-level radioactive waste management. This report discusses the incentives of P-T, generation of long-lived nuclides in fission reactors, nuclear transmutation technologies, R and D activities of the partitioning and transmutation technology development programs at JAERI and in the world. (author)

Partitioning and transmutation. Annual Report 1997

Energy Technology Data Exchange (ETDEWEB)

Enarsson, Aa; Landgren, A; Liljenzin, J O; Skaalberg, M; Spjuth, L [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Nuclear Chemistry

1997-12-01

The current research project on partitioning and transmutation at the Dept. of Nuclear Chemistry, CTH, has the primary objective to investigate separation processes useful in connection with transmutation of long-lived radionuclides in high level nuclear waste. Partitioning is necessary in order to recover and purify the elements before and after each irradiation in a P and T treatment. In order to achieve a high transmutation efficiency the chemical separation process used must have small losses to various waste streams. At present, only aqueous based separation processes are known to be able to achieve the high recovery and separation efficiencies necessary for a useful P and T process. Refs, figs, tabs.

A Los Alamos concept for accelerator transmutation of waste and energy production (ATW)

International Nuclear Information System (INIS)

1990-01-01

This document contains the diagrams presented at the ATW (Accelerator Transmutation of Waste and Energy Production) External Review, December 10-12, 1990, held at Los Alamos National Laboratory. Included are the charge to the committee and the presentations for the committee's review. Topics of the presentations included an overview of the concept, LINAC technology, near-term application -- high-level defense wastes (intense thermal neutron source, chemistry and materials), advanced application of the ATW concept -- fission energy without a high-level waste stream (overview, advanced technology, and advanced chemistry), and a summary of the research issues

Consultancy on the potential of fusion/fission sub-critical neutron systems for energy production and transmutation. Working material

International Nuclear Information System (INIS)

2005-01-01

possible activities to be implemented under IAEA aegis. The Consultancy examined existing experimental facilities and devices that could produce 14 MeV neutrons in the near future to permit the first concrete steps toward fusion-fission systems and how such a facility can become an integral part of the effort to develop sub-critical reactors, presently spearheaded by accelerator driven systems. In support of this effort, the Consultancy discussed and proposed a set of studies that permit future inter-comparison between various utilization and/or transmutation technologies, including accelerator driven systems and possible DT-plasma fusion devices for such application in the near future. The Consultancy recommended enhanced coordinated efforts for developing DT-plasma fusion driven sub-critical core designs. The main areas requiring enhanced research and technology development are nuclear data, forms and preparation of fuel, chemistry control, sub-critical core design, and systems integration

Average fast neutron flux in three energy ranges in the Quinta assembly irradiated by two types of beams

Directory of Open Access Journals (Sweden)

Strugalska-Gola Elzbieta

2017-01-01

Full Text Available This work was performed within the international project “Energy plus Transmutation of Radioactive Wastes” (E&T - RAW for investigations of energy production and transmutation of radioactive waste of the nuclear power industry. 89Y (Yttrium 89 samples were located in the Quinta assembly in order to measure an average high neutron flux density in three different energy ranges using deuteron and proton beams from Dubna accelerators. Our analysis showed that the neutron density flux for the neutron energy range 20.8 - 32.7 MeV is higher than for the neutron energy range 11.5 - 20.8 MeV both for protons with an energy of 0.66 GeV and deuterons with an energy of 2 GeV, while for deuteron beams of 4 and 6 GeV we did not observe this.

Minor actinides transmutation potential: state of art for GEN IV sodium cooled fast reactors

International Nuclear Information System (INIS)

Buiron, Laurent

2015-01-01

In the frame of the R and D program relative to the 1991 French act on nuclear waste management, fast neutron systems have shown relevant characteristics that meet both requirements on sustainable resources management and waste minimization. They also offer flexibility by mean of burner or breeder configurations allowing mastering plutonium inventory without significant impact on core safety. From the technological point of view, sodium cooled fast reactor are considered in order to achieve mean term industrial deployment. The present document summaries the main results of R and D program on minor actinides transmutation in sodium fast reactor since 2006 following recommendation of the first part of the 1991 French act. Both homogeneous and heterogeneous management achievable performances are presented for 'evolutionary' SFR V2B core as well as low void worth CFV core for industrial scale configurations (1500 MWe). Minor actinides transmutation could be demonstrated in the ASTRID reactor with the following configurations: - a 2%vol Americium content for the homogeneous mode, - a 10%vol Americium content for the heterogeneous mode, without any substantial modification of the main core safety parameters and only limited impacts on the associated fuel cycle (manufacturing issues are not considered here). In order to achieve such goal, a wide range of experimental irradiations driven by transmutation scenarios have to be performed for both homogeneous and heterogeneous minor actinides management. (author) [fr

Elastic neutron scattering studies at 96 MeV for transmutation.

Science.gov (United States)

Osterlund, M; Blomgren, J; Hayashi, M; Mermod, P; Nilsson, L; Pomp, S; Ohrn, A; Prokofiev, A V; Tippawan, U

2007-01-01

Elastic neutron scattering from (12)C, (14)N, (16)O, (28)Si, (40)Ca, (56)Fe, (89)Y and (208)Pb has been studied at 96 MeV in the10-70 degrees interval, using the SCANDAL (SCAttered Nucleon Detection AssembLy) facility. The results for (12)C and (208)Pb have recently been published, while the data on the other nuclei are under analysis. The achieved energy resolution, 3.7 MeV, is about an order of magnitude better than for any previous experiment above 65 MeV incident energy. A novel method for normalisation of the absolute scale of the cross section has been used. The estimated normalisation uncertainty, 3%, is unprecedented for a neutron-induced differential cross section measurement on a nuclear target. Elastic neutron scattering is of utmost importance for a vast number of applications. Besides its fundamental importance as a laboratory for tests of isospin dependence in the nucleon-nucleon, and nucleon-nucleus, interaction, knowledge of the optical potentials derived from elastic scattering come into play in virtually every application where a detailed understanding of nuclear processes is important. Applications for these measurements are dose effects due to fast neutrons, including fast neutron therapy, as well as nuclear waste incineration and single event upsets in electronics. The results at light nuclei of medical relevance ((12)C, (14)N and (16)O) are presented separately. In the present contribution, results on the heavier nuclei are presented, among which several are of relevance to shielding of fast neutrons.

Minor actinides transmutation performance in a fast reactor

International Nuclear Information System (INIS)

Takeda, Toshikazu

2016-01-01

Highlights: • A method for calculating MA transmutation for individual nuclides has been proposed by introducing two formulas of the MA transmutation. One corresponds to the difference of MA amounts, and the other corresponds to the sum of the fission amounts and the plutonium production amounts. • Using the method the MA transmutation was calculated for Np-237 and Am-241 in a fast reactor. The burnup period was changed from 1 year to 12 year. • For the 1 year burnup a large amount of Am-242m, Cm-242 are produced from Am-241. The total MA transmutation amount increases with burnup time, but its gradient with respect to burnup time decreases after 9 years, and the transmutation amount by overall fission increases almost linearly with burnup time. • However, after the 6 year burnup the fission contribution became large because of the large production of Pu isotopes from the original Am-241. • In addition to the homogeneous loading of the MA nuclides into the cores, a heterogeneous loading of Am-241 to the blanket region was considered. - Abstract: Results obtained in the project named “Study on Minor Actinides Transmutation using Monju Data”, which has been sponsored by the Ministry of Education, Culture, Sports, Science and Technology in Japan (MEXT) are described. In order to physically understand transmutation of individual MA nuclides in fast reactors, a new method was developed in which the MAs transmutation is interpreted by two formulas. One corresponds to the difference of individual MA nuclides amounts before and after a burnup period, and the other is the sum of amount of fission of a relevant MA nuclide and the net plutonium production from the MA nuclide during a burnup period. The method has been applied to two fast reactors with MA fuels loaded in cores homogeneously and in a blanket region heterogeneously. Numerical results of MA transmutation for the two reactors are shown.

Conceptual design of multi-purpose accelerator-driven transmutation test facility

International Nuclear Information System (INIS)

Hirota, Koichi; Hida, Kenzo; Yokobori, Hitoshi; Kamishima, Yoshio

1999-01-01

The Japan Atomic Energy Research Institute (JAERI) has been developing a concept of accelerator-driven transmutation system using a high-power proton linac. To demonstrate the technical feasibility of this concept, accelerator-driven spallation experiments will be necessary. We believe our proposal of a multi-purpose test facility is a promising concept to clarify its feasibility from the basic neutronics and engineering standpoint. The main feature of our initial proposal is using an inclined beam injection. It enables to simplify the head of the test vessel as well as to facilitate easy replacing of the beam window and the testing device containing the test specimen, and also this system will minimize the complexity of the vessel head and surrounding structures. Next proposal is using an ordinary overhead beam injection system and is modified to be simple structural concept of the test vessel from inclined beam injection. At the first step, the basic neutronics experiments will be performed. At this step, the test device and the cooling device are simpler ones, due to only small heat will be generated. Then we plan using a gas cooling. At the following steps, the test device and the vessel internal structures will be remodeled or remade to adjust to the test purposes, if necessary. At these steps, target material tests and thermal hydraulic tests using some liquid metal coolants will be done. In this case, the natural circulation cooling will be done. To verify the transmutation technology, a larger heat will be generated, so a forced coolant circulation system will be installed in the test vessel. This system consists of a heat exchanger and a circulation pump. The vessel internal structure will be remade. Doing such step-wise remaking, initial construction cost of the proposed test facility will be expected to be reasonable. (author)

Prompt nuclear analytical techniques for material research in accelerator driven transmutation technologies: Prospects and quantitative analyses

International Nuclear Information System (INIS)

Vacik, J.; Hnatowicz, V.; Cervena, J.; Perina, V.; Mach, R.

1998-01-01

Accelerator driven transmutation technology (ADTT) is a promising way toward liquidation of spent nuclear fuel, nuclear wastes and weapon grade Pu. The ADTT facility comprises a high current (proton) accelerator supplying a sub-critical reactor assembly with spallation neutrons. The reactor part is supposed to be cooled by molten fluorides or metals which serve, at the same time, as a carrier of nuclear fuel. Assumed high working temperature (400-600 C) and high radiation load in the subcritical reactor and spallation neutron source put forward the problem of optimal choice of ADTT construction materials, especially from the point of their radiation and corrosion resistance when in contact with liquid working media. The use of prompt nuclear analytical techniques in ADTT related material research is considered and examples of preliminary analytical results obtained using neutron depth profiling method are shown for illustration. (orig.)

Consultancy to review and finalize the IAEA publication 'Compendium on the use of fusion/fission hybrids for the utilization and transmutation of actinides and long-lived fission products'. Working material

International Nuclear Information System (INIS)

2004-01-01

In addition to the traditional fission reactor research, fusion R and D activities are becoming of interest also to nuclear fission power development. There is renewed interest in utilizing fusion neutrons, Heavy Liquid Metals, and molten salts for innovative systems (energy production and transmutation). Indeed, for nuclear power development to become sustainable as a long-term energy option, innovative fuel cycle and reactor technologies will have to be developed to solve the problems of resource utilization and long-lived radioactive waste management. In this context Member States clearly expressed the need for comparative assessments of various transmutation reactors. Both the fusion and fission communities are currently investigating the potential of innovative reactor and fuel cycle strategies that include a fusion/fission system. The attention is mainly focused on substantiating the potential advantages of such systems: utilization and transmutation of actinides and long-lived fission products, intrinsic safety features, enhanced proliferation resistance, and fuel breeding capabilities. An important aspect of the ongoing activities is the comparison with the accelerator driven subcritical system (spallation neutron source), which is the other main option for producing excess neutrons. Apart from comparative assessments, knowledge preservation is another subject of interest to the Member States: the goal, applied to fusion/fission systems, is to review the status of, and to produce a 'compendium' of past and present achievements in this area

Transmutation Theory in the Greek Alchemical Corpus.

Science.gov (United States)

Dufault, Olivier

2015-08-01

This paper studies transmutation theory as found in the texts attributed to Zosimus of Panopolis, "the philosopher Synesius," and "the philosopher Olympiodorus of Alexandria." It shows that transmutation theory (i.e. a theory explaining the complete transformation of substances) is mostly absent from the work attributed to these three authors. The text attributed to Synesius describes a gilding process, which is similar to those described by Pliny and Vitruvius. The commentary attributed to Olympiodorus is the only text studied here that describes something similar to a transmutation theory. It is unclear, however, if this was a theory of transmutation or if the writer meant something more like the literal meaning of the word "ekstrophē," a term used to describe the transformation of metals, as the "turning inside-out" of what is hidden in a substance. A similar conception of ekstrophē can be found in the works of Zosimus, who discussed transmutation to make an analogy with self-purification processes, which, from the perspective of his own anthropogony, consisted in the "turning inside-out" of the "inner human" (esō anthrōpos).

Transmutation and activation of stainless steel 316 SS in a thermal fusion reactor blanket

International Nuclear Information System (INIS)

Gruber, J.; Schneider, J.

1977-10-01

Using the program MATEXP (matrix exponential method) the influence of neutron flux is calculated for stainless steel 3s16 SS which is used as a structural material in a fusion reactor blanket (CTRD-I). The transmutations, activations and γ-dose rates are determined for an operation time of 20 years. Investigating the decay behaviour after operation time, we found that the long term activity and dose rate was mainly influenced by five nuclides: Fe55, Ni63, Ni59, Co60 and Nb94. (orig.) [de

Effects of silicon cross section and neutron spectrum on the radial uniformity in neutron transmutation doping.

Science.gov (United States)

Kim, Haksung; Ho Pyeon, Cheol; Lim, Jae-Yong; Misawa, Tsuyoshi

2012-01-01

The effects of silicon cross section and neutron spectrum on the radial uniformity of a Si-ingot are examined experimentally with various neutron spectrum conditions. For the cross section effect, the numerical results using silicon single crystal cross section reveal good agreements with experiments within relative difference of 6%, whereas the discrepancy is approximately 20% in free-gas cross section. For the neutron spectrum effect, the radial uniformity in hard neutron spectrum is found to be more flattening than that in soft spectrum. Copyright © 2011 Elsevier Ltd. All rights reserved.

Prognosis and comparison of performances of composite CERCER and CERMET fuels dedicated to transmutation of TRU in an EFIT ADS

Science.gov (United States)

Sobolev, V.; Uyttenhove, W.; Thetford, R.; Maschek, W.

2011-07-01

The neutronic and thermomechanical performances of two composite fuel systems: CERCER with (Pu,Np,Am,Cm)O 2-x fuel particles in ceramic MgO matrix and CERMET with metallic Mo matrix, selected for transmutation of minor actinides in the European Facility for Industrial Transmutation (EFIT), were analysed aiming at their optimisation. The ALEPH burnup code system, based on MNCPX and ORIGEN codes and JEFF3.1 nuclear data library, and the modern version of the fuel rod performance code TRAFIC were used for this analysis. Because experimental data on the properties of the mixed minor-actinide oxides are scarce, and the in-reactor behaviour of the T91 steel chosen as cladding, as well as of the corrosion protective layer, is still not well-known, a set of "best estimates" provided the properties used in the code. The obtained results indicate that both fuel candidates, CERCER and CERMET, can satisfy the fuel design and safety criteria of EFIT. The residence time for both types of fuel elements can reach about 5 years with the reactivity swing within ±1000 pcm, and about 22% of the loaded MA is transmuted during this period. However, the fuel centreline temperature in the hottest CERCER fuel rod is close to the temperature above which MgO matrix becomes chemically instable. Moreover, a weak PCMI can appear in about 3 years of operation. The CERMET fuel can provide larger safety margins: the fuel temperature is more than 1000 K below the permitted level of 2380 K and the pellet-cladding gap remains open until the end of operation.

Inert matrix fuels for incineration of plutonium and transmutation of americium

International Nuclear Information System (INIS)

Matzke, Hj.

2000-01-01

In conventional U-based nuclear fuels, both Pu and higher actinides (mainly Am, but also Np and Cm) are formed by neutron capture reactions and α- or β-decay. If a strategy of reprocessing is adopted as in some European nations and in Japan, the separated Pu can be recycled as (U, Pu)O 2 (or mixed-oxide-MOX) fuel. The high-level liquid waste of reprocessing is presently vitrified. However, the alternative of separating the minor actinides from the fission products (partitioning) and subsequent transmutation in existing reactors or in new dedicated actinide burners is widely studied as a possible means to reduce the radiotoxicity of the waste

Copper Doping of Zinc Oxide by Nuclear Transmutation

Science.gov (United States)

2014-03-27

Copper Doping of Zinc Oxide by Nuclear Transmutation THESIS Matthew C. Recker, Captain, USAF AFIT-ENP-14-M-30 DEPARTMENT OF THE AIR FORCE AIR...NUCLEAR TRANSMUTATION THESIS Presented to the Faculty Department of Engineering Physics Graduate School of Engineering and Management Air Force...COPPER DOPING OF ZINC OXIDE BY NUCLEAR TRANSMUTATION Matthew C. Recker, BS Captain, USAF Approved: //signed// 27 February 2014 John W. McClory, PhD

Application of gas-cooled Accelerator Driven System (ADS) transmutation devices to sustainable nuclear energy development

Energy Technology Data Exchange (ETDEWEB)

Abanades, A., E-mail: abanades@etsii.upm.es [ETSII/Universidad Politecnica de Madrid, J.Gutierrez Abascal, 2-28006 Madrid (Spain); Garcia, C.; Garcia, L. [Instituto Superior de Tecnologia y Ciencias Aplicadas. Quinta de los, Molinos, Ave. Salvador Allende y Luaces, Ciudad de la Habana, CP 10400, Apartado Postal 6163 (Cuba); Escriva, A.; Perez-Navarro, A. [Instituto de Ingenieria Energetica, Universidad Politecnica de Valencia, C.P. 46022 Valencia (Spain); Rosales, J. [Instituto Superior de Tecnologia y Ciencias Aplicadas. Quinta de los, Molinos, Ave. Salvador Allende y Luaces, Ciudad de la Habana, CP 10400, Apartado Postal 6163 (Cuba)

2011-06-15

Highlights: > Utilization of Accelerator Driven System (ADS) for Hydrogen production. > Evaluation of the potential use of gas-cooled ADS for a sustainable use of Uranium resources by transmutation of nuclear wastes, electricity and Hydrogen production. > Application of the Sulfur-Iodine thermochemical process to subcritical systems. > Application of CINDER90 to calculate burn-up in subcritical systems. - Abstract: The conceptual design of a pebble bed gas-cooled transmutation device is shown with the aim to evaluate its potential for its deployment in the context of the sustainable nuclear energy development, which considers high temperature reactors for their operation in cogeneration mode, producing electricity, heat and Hydrogen. As differential characteristics our device operates in subcritical mode, driven by a neutron source activated by an accelerator that adds clear safety advantages and fuel flexibility opening the possibility to reduce the nuclear stockpile producing energy from actual LWR irradiated fuel with an efficiency of 45-46%, either in the form of Hydrogen, electricity, or both.

Transmutation in ASTRID

International Nuclear Information System (INIS)

Grouiller, Jean-Paul; Buiron, Laurent; Mignot, Gérard; Palhier, Raphael

2013-01-01

Summary and future prospects for incorporating Am in ASTRID: → Potential to demonstrate the minor actinide transmutation on an industrial scale in the CFV V1 core of ASTRID: • Homogeneous concept: 2% of Am in a standard fuel; • Heterogeneous concept: 10% on UO 2 in the radial blanket. • The objective of ensuring a balance in the Am (and total minor actinides) flow in the ASTRID fuel cycle may be obtained without any impact on the design of the core and handling systems for the management of the new and spent fuel subassemblies. • Several experimental phases in ASTRID to implement different transmutation scenarios using homogeneous and heterogeneous concepts. ⇒ the availability of facilities involved in the ASTRID material cycles

Design Concept of Kijang Research Reactor for Neutron Transmutation Doping of 300 MM ingots

International Nuclear Information System (INIS)

Jun, B. J.; Kim, H. S.; Seo, C. G.; Kim, H. C.; Lee, B. C.

2013-01-01

Neutron transmutation doping will be one of the important utilization areas of the Kijang research reactor, which is currently under design. The reactor will serve for at least 50 years. As the diameter of a current NTD ingot is already large compared to the size of the reactor, unless a provision in the reactor design is specifically made for the irradiation of potential larger diameter ingots in the future, the lifetime sustainability of the NTD activity, if possible, may be difficult to achieve. While 200 mm became the largest diameter of NTD wafers a few years ago, 300 mm is the majority nowadays in the silicon semiconductor market, and one of the world leading device companies recently invested in the construction of a 450 mm fabrication plant. The usual peak time of a wafer diameter has been around 12 years. Though the generation gap of a NTD wafer diameter has become longer as time has passed, we can foresee that NTD demand for 300 mm ingots will arise within 20 years if their NTD is possible. Our calculations show that the radial uniformity for the 300 mm ingot irradiation may be acceptable by wafer companies. However, the NTD for 450 mm ingots is judged as impractical. The KJRR is designed to irradiate 6' and 200 mm ingots to accommodate the major demands in the current and near future markets. We suppose that a 6' irradiation facility will be modified into a 300 mm irradiation facility when the demand for a 300 mm NTD arises. As the demand for the 300 mm NTD increases, other 6' and 200 mm NTD facilities will be modified one by one. A minimization of the component replacement and long-lived radwaste and a facilitation of the replacement work for each modification are important factors along with a better performance of NTD facilities

Lead-Bismuth-Eutectic Spallation Neutron Source for Nuclear Transmuter

International Nuclear Information System (INIS)

Gohar, Y.; Herceg, J.; Krajtl, L.; Micklich, B.; Pointer, D.; Saiveau, J.; Sofu, T.; Finck, P.

2002-01-01

A lead-bismuth eutectic (LBE) spallation target design concept has been developed for the subcritical multiplier (SCM) design of the accelerator-driven test facility (ADTF). The design is based on a coaxial geometrical configuration, which has been carefully analyzed and designed to achieve an optimum performance. The target design description, the results from the parametric studies, and the design analyses including neutronics, heat transfer, and hydraulics analyses are given in this paper. A detailed MCNPX geometrical model for the target has been developed to generate heating rates and nuclear responses in the structural material for the design process. The beam has a uniform distribution of 600 MeV protons and 5-MW total power. A small LBE buffer is optimized to reduce the irradiation damage in the SCM fuel elements from the scatter protons and the high-energy neutrons, to maximize the neutron yield to the SCM operation, and to provide inlet and outlet manifolds for the LBE coolant. A special attention has been given to the target window design to enhance its lifetime. The window volumetric heating is 766 W/cm 3 relative to 750 W/cm 3 in LBE for a 40-μA/cm 2 current density. The results show that the nuclear heating from the proton beam diminishes at about 32 cm along the beam axis in the LBE target material. The neutron contribution to the atomic displacement is in the range of 94 to ∼100% for the structure material outside the proton beam path. In the beam window, the neutron contribution is ∼74% and the proton beam is responsible for more than 95% of the total gas production. The proton contribution to the gas production vanishes outside the beam path. The LBE average velocity is ∼2 m/s. The heat transfer and the hydraulics analyses have been iterated to reduce the maximum temperature and the thermal stress level in the target window to enhance its operating life. (authors)

Transient Analyses for a Molten Salt Transmutation Reactor Using the Extended SIMMER-III Code

International Nuclear Information System (INIS)

Wang, Shisheng; Rineiski, Andrei; Maschek, Werner; Ignatiev, Victor

2006-01-01

Recent developments extending the capabilities of the SIMMER-III code for the dealing with transient and accidents in Molten Salt Reactors (MSRs) are presented. These extensions refer to the movable precursor modeling within the space-time dependent neutronics framework of SIMMER-III, to the molten salt flow modeling, and to new equations of state for various salts. An important new SIMMER-III feature is that the space-time distribution of the various precursor families with different decay constants can be computed and took into account in neutron/reactivity balance calculations and, if necessary, visualized. The system is coded and tested for a molten salt transmuter. This new feature is also of interest in core disruptive accidents of fast reactors when the core melts and the molten fuel is redistributed. (authors)

Transmuted Complementary Weibull Geometric Distribution

Directory of Open Access Journals (Sweden)

Ahmed Z. A…fify

2014-12-01

Full Text Available This paper provides a new generalization of the complementary Weibull geometric distribution that introduced by Tojeiro et al. (2014, using the quadratic rank transmutation map studied by Shaw and Buckley (2007. The new distribution is referred to as transmuted complementary Weibull geometric distribution (TCWGD. The TCWG distribution includes as special cases the complementary Weibull geometric distribution (CWGD, complementary exponential geometric distribution(CEGD,Weibull distribution (WD and exponential distribution (ED. Various structural properties of the new distribution including moments, quantiles, moment generating function and RØnyi entropy of the subject distribution are derived. We proposed the method of maximum likelihood for estimating the model parameters and obtain the observed information matrix. A real data set are used to compare the ‡exibility of the transmuted version versus the complementary Weibull geometric distribution.

Time-grated energy-selected cold neutron radiography

International Nuclear Information System (INIS)

McDonald, T.E. Jr.; Brun, T.O.; Claytor, T.N.; Farnum, E.H.; Greene, G.L.; Morris, C.

1998-01-01

A technique is under development at the Los Alamos Neutron Science Center (LANSCE), Manuel Lujan Jr. Neutron Scattering Center (Lujan Center) for producing neutron radiography using only a narrow energy range of cold neutrons. The technique, referred to as Time-Gated Energy-Selected (TGES) neutron radiography, employs the pulsed neutron source at the Lujan Center with time of flight to obtain a neutron pulse having an energy distribution that is a function of the arrival time at the imager. The radiograph is formed on a short persistence scintillator and a gated, intensified, cooled CCD camera is employed to record the images, which are produced at the specific neutron energy range determined by the camera gate. The technique has been used to achieve a degree of material discrimination in radiographic images. For some materials, such as beryllium and carbon, at energies above the Bragg cutoff the neutron scattering cross section is relatively high while at energies below the Bragg cutoff the scattering cross section drops significantly. This difference in scattering characteristics can be recorded in the TGES radiography and, because the Bragg cutoff occurs at different energy levels for various materials, the approach can be used to differentiate among these materials. This paper outlines the TGES radiography technique and shows an example of radiography using the approach

Status of neutron dosimetry and damage analysis for the fusion materials program

International Nuclear Information System (INIS)

Greenwood, L.R.

1979-01-01

The status of neutron flux and spectral measurements is described for fusion material irradiations at reactor, T(d,n), Be(d,n), and spallation neutron sources. Such measurements are required for the characterization of an irradiation in terms of displacement damage, gas and transmutant production. Emphasis is placed on nuclear data deficiencies with specific recommendations for cross section measurements and calculations

Analysis of the minority actinides transmutation in a sodium fast reactor with uniform load pattern by the MCNPX-CINDER code

International Nuclear Information System (INIS)

Ochoa Valero, R.; Garcia-Herranz, N.; Aragones, J. M.

2010-01-01

The aim of this study is to evaluate the minority actinides transmutation in sodium fast reactors (SFR) assuming a uniform load pattern. It is determined the isotopic evolution of the actinides along burn, and the evolution of the reactivity and the reactivity coefficients. For that, it is used the MCNPX neutron transport code coupled with the inventory code CINDER90.

Selection method and characterization of neutron monochromator natural crystals

International Nuclear Information System (INIS)

Stasiulevicius, R.; Kastner, G.F.

2000-01-01

Thermal neutrons are important analytical tools for microscopic material probe. These neutrons can be selected by diffraction technique using monocrystal, usually artificial. A crystal selection process was implemented and the characteristics of natural specimens were studied by activation analysis-k 0 method. The representative 120 samples, of which 21 best types, were irradiated in IPR-R1 and measured with a neutron diffractometer at IEA-R1m Brazilian reactors. These results are useful for database build up and ease the choice of appropriate natural crystal, with some advantage options: highest intensity diffracted, enlarging the energy operational interval and optimal performance in special applications. (author)

A study on transmutation of LLFPs using various types of HTGRs

Energy Technology Data Exchange (ETDEWEB)

Kora, Kazuki, E-mail: kora_k@nucl.kyushu-u.ac.jp [Department of Applied Quantum Physics and Nuclear Engineering, Kyushu University, 744 Motooka, Nishi-ku, Fukuoka-shi, Fukuoka-ken (Japan); Nakaya, Hiroyuki; Matsuura, Hideaki [Department of Applied Quantum Physics and Nuclear Engineering, Kyushu University, 744 Motooka, Nishi-ku, Fukuoka-shi, Fukuoka-ken (Japan); Goto, Minoru; Nakagawa, Shigeaki; Shimakawa, Satoshi [Japan Atomic Energy Agency, 4002 Narita-cho, Oarai-machi, Higashiibaraki-gun, Ibaraki, Ibaraki-ken (Japan)

2016-04-15

Highlights: • We propose utilization of a variety of HTGRs for LLFP transmutation and storage. • The transmutation performance of four types of HTGRs was examined and compared. • Some types of HTGRs show preferable characteristics for LLFP transmutation. - Abstract: In order to investigate the potential of high temperature gas-cooled reactors (HTGRs) for transmutation of long-lived fission products (LLFPs), numerical simulation of four types of HTGRs were carried out. In addition to the gas-turbine high temperature reactor system “GTHTR300”, which is the subject of our previous research, a small modular HTGR plant “HTR50S” and two types of plutonium burner HTGRs “Clean Burn with MA” and “Clean Burn without MA” were considered. The simulation results show that an early realization of LLFP transmutation using a compact HTGR may be possible since the HTR50S can transmute fair amount of LLFPs for its thermal output. The Clean Burn with MA can transmute a limited amount of LLFPs. However, an efficient LLFP transmutation using the Clean Burn without MA seems to be convincing as it is able to achieve very high burn-ups and produce LLFP transmutation more than GTHTR300. Based on these results, we propose utilization of variety of HTGRs for LLFP transmutation and storage.

Effect of Target Configuration on the Neutronic Performance of the Gas-Cooled ADS

CERN Document Server

Biss, K; Shetty, N; Nabbi, R

2013-01-01

With the utilization of nuclear energy transuranic elements like Pu, Am and Cm are produced causing high, long term radioactivity and radio toxicity, respectively. To reduce the radiological impact on the environment and to the repository Partitioning and Transmutation is considered as an efficient way. In this respect comprehensive research works are performed at different research institutes worldwide. The results show that the transmutation of TRU is achieved with fast neutrons due to the higher fission probability. Based on Accelerator Driven Systems (ADS) those neutrons are used in a particular system, in which mainly liquid metal eutectic (lead bismuth) is used as coolant. The neutronic performance of an ADS system based on gas cooling was studied in this work by using the simulation tool MCNPX. The usage of the Monte-Carlo method in MCNPX allows the simulation of the physical processes in a 3D-model of the core. In dependence of the spallation target material and design several parameters like the mult...

Development of the external cooling device of increase the productivity of neutron-transmutation-doped silicon semiconductor (NTD-Si) (Joint research)

International Nuclear Information System (INIS)

Hirose, Akira; Wada, Shigeru; Sasajima, Fumio; Kusunoki, Tsuyoshi; Kameyama, Iwao; Aizawa, Ryouji; Kikuchi, Naoyuki

2007-01-01

Neutron-Transmutation-Doped Silicon Semiconductor (hereinafter referred as 'NTD-Si') is the best semiconductor for the power device. The needs of NTD-Si increase recently in proportion to the popularization of hybrid-cars. A fission research reactor, which is a steady state neutron source, is being expected as the best device to meet the needs. So far, we have reconsidered the existing approach which is employed for NTD-Si production works at the research reactors JRR-3, JRR-4 and JMTR of JAEA so as to meet the needs. As one of the effective measures, we found out that the productivity can be increased by incorporating a new device to cool down radioactivity of irradiated silicon ingots at the place outside the main stream from the loading of silicon ingots to the withdrawal of irradiated ingots to the existing JRR-3 Uniformity Irradiation System. Consequently, we developed and installed the device (hereinafter referred as 'external cooling device'). After an ingot was irradiated once, it is turned over manually and irradiated again in order to irradiate the ingot uniformly. With the conventional system, it was necessary to wait the radioactivity of ingot decrease less than the permissible level with holding the ingot in the irradiation equipment. It was effective to shorten the waiting period by using an external cooling device for production increase of NTD-Si. It is expected that the productivity of NTD-Si will be increased by using the external cooling device. This report mentions the design of the external cooling device and verification between its design specifications and the performance of the device completed. (author)

Nuclear transmutation. The reality of cold fusion

International Nuclear Information System (INIS)

Mizuno, Tadahiko

1997-01-01

The book is introducing the quest on the way to reality of cold fusion. Another point of author is interaction between the quest and social impacts. After the first report on cold fusion by M. Fleischmann and S. Pons on March 1989, the inspired author started a series of following experiments based on his own characteristic background of electrochemistry. The first experiment from March 25 to April 7, 1989 did not show any indications on neutrons, gamma rays, tritium, and heat. The second experiment was initiated at the underground experimental hall of the linear accelerator facilities. This means the shielding of noises coming from outsides. The neutron of about 2.45 MeV was observed after the 1-month continuation of the experiment. The intensity of neutron was nearly 10 to 20 times of the background noise. Furthermore, there were no changes of signals on heat and tritium before and after the experiments. The closed cell experiment was conducted to keep reliability of the experiment. The experiment started on June 1990. In this case, Tritium signals of 100 times of background noise were observed, however, no meaningful signal on neutrons. Anomalous heat was observed after March 24, 1991, where the electric current was increased up to 6 A. On the other hand, there were no appreciable change in neutron and tritium signals. The solid electrolysis was used in the experiment after May 1992, for its high temperature characteristics, where anomalous heat was observed with a certain probability. The experimental system was upgraded in diagnostic methods after 1994. As a result, particular isotopes related to fission reaction were detected. This fact indicates some kinds of transmutations at very local area of the solid surfaces. The author has also pointed out many reactions for a series of this scientific results responded by, for example, well known professors, scientific societies, mass media, and international conferences. Consequently the reactions had almost smeared

Study of response of 3He detectors to monoenergetic neutrons

International Nuclear Information System (INIS)

Abanades, A.; Andriamonje, S.; Arnould, H.; Barreau, G.; Bercion, M.; Casagrande, F.; Cennini, P.; Del Moral, R.; Gonzales, E.; Lacoste, V.; Pdemay, G.; Pravikoff, M.S.

1997-01-01

In the search of a hybrid system (the coupling of the particle accelerator to an under-critical reactor) for radioactive waste transmutation the TARC (Transmutation by Adiabatic Resonance Crossing) program has been developed. Due to experimental limitations, the time-energy relation at higher neutron energies, particularly, around 2 MeV, which is an important domain for TARC, cannot be applied. Consequently the responses of the 3 He ionization neutron detector developed for TARC experiment have been studied using a fast monoenergetic neutron source. The neutrons were produced by the interaction of the proton delivered by Van de Graaff accelerator of CENBG. The originality of the detector consists in its structure of three series of electric conductors which are mounted around the anode: a grid ensuring the detector proportionality, a cylindrical suit of alternating positive voltage and grounded wires aiming at eliminating the radial end effects, serving as veto and two cylinders serving as end plugs to eliminate the perpendicular end effects. Examples of anode spectra conditioned (in anticoincidence) by the mentioned vetoes are given. One can see the contribution of the elastic scattering from H and 3 He. By collimating the neutron beam through a borated polyethylene system it was possible to obtain a mapping of the detector allowing the study of its response as a function of the irradiated zones (anode and grid)

Fusion transmutation of waste: design and analysis of the in-zinerator concept.

Energy Technology Data Exchange (ETDEWEB)

Durbin, S. M.; Cipiti, Benjamin B.; Olson, Craig Lee; Guild-Bingham, Avery (Texas A& M University, College Station, TX); Venneri, Francesco (General Atomics, San Diego, CA); Meier, Wayne (LLNL, Livermore, CA); Alajo, A.B. (Texas A& M University, College Station, TX); Johnson, T. R. (Argonne Mational Laboratory, Argonne, IL); El-Guebaly, L. A. (University of Wisconsin, Madison, WI); Youssef, M. E. (University of California, Los Angeles, CA); Young, Michael F.; Drennen, Thomas E. (Hobart & William Smith College, Geneva, NY); Tsvetkov, Pavel Valeryevich (Texas A& M University, College Station, TX); Morrow, Charles W.; Turgeon, Matthew C.; Wilson, Paul (University of Wisconsin, Madison, WI); Phruksarojanakun, Phiphat (University of Wisconsin, Madison, WI); Grady, Ryan (University of Wisconsin, Madison, WI); Keith, Rodney L.; Smith, James Dean; Cook, Jason T.; Sviatoslavsky, Igor N. (University of Wisconsin, Madison, WI); Willit, J. L. (Argonne Mational Laboratory, Argonne, IL); Cleary, Virginia D.; Kamery, William (Hobart & William Smith College, Geneva, NY); Mehlhorn, Thomas Alan; Rochau, Gary Eugene

2006-11-01

Due to increasing concerns over the buildup of long-lived transuranic isotopes in spent nuclear fuel waste, attention has been given in recent years to technologies that can burn up these species. The separation and transmutation of transuranics is part of a solution to decreasing the volume and heat load of nuclear waste significantly to increase the repository capacity. A fusion neutron source can be used for transmutation as an alternative to fast reactor systems. Sandia National Laboratories is investigating the use of a Z-Pinch fusion driver for this application. This report summarizes the initial design and engineering issues of this ''In-Zinerator'' concept. Relatively modest fusion requirements on the order of 20 MW can be used to drive a sub-critical, actinide-bearing, fluid blanket. The fluid fuel eliminates the need for expensive fuel fabrication and allows for continuous refueling and removal of fission products. This reactor has the capability of burning up 1,280 kg of actinides per year while at the same time producing 3,000 MWth. The report discusses the baseline design, engineering issues, modeling results, safety issues, and fuel cycle impact.

Fusion transmutation of waste: design and analysis of the In-Zinerator concept

International Nuclear Information System (INIS)

Durbin, S. M.; Cipiti, Benjamin B.; Olson, Craig Lee; Guild-Bingham, Avery; Venneri, Francesco; Meier, Wayne; Alajo, A.B.; Johnson, T. R.; El-Guebaly, L. A.; Youssef, M. E.; Young, Michael F.; Drennen, Thomas E.; Tsvetkov, Pavel Valeryevich; Morrow, Charles W.; Turgeon, Matthew C.; Wilson, Paul; Phruksarojanakun, Phiphat; Grady, Ryan; Keith, Rodney L.; Smith, James Dean; Cook, Jason T.; Sviatoslavsky, Igor N.; Willit, J. L.; Cleary, Virginia D.; Kamery, William; Mehlhorn, Thomas Alan; Rochau, Gary Eugene

2006-01-01

Due to increasing concerns over the buildup of long-lived transuranic isotopes in spent nuclear fuel waste, attention has been given in recent years to technologies that can burn up these species. The separation and transmutation of transuranics is part of a solution to decreasing the volume and heat load of nuclear waste significantly to increase the repository capacity. A fusion neutron source can be used for transmutation as an alternative to fast reactor systems. Sandia National Laboratories is investigating the use of a Z-Pinch fusion driver for this application. This report summarizes the initial design and engineering issues of this ''In-Zinerator'' concept. Relatively modest fusion requirements on the order of 20 MW can be used to drive a sub-critical, actinide-bearing, fluid blanket. The fluid fuel eliminates the need for expensive fuel fabrication and allows for continuous refueling and removal of fission products. This reactor has the capability of burning up 1,280 kg of actinides per year while at the same time producing 3,000 MWth. The report discusses the baseline design, engineering issues, modeling results, safety issues, and fuel cycle impact

The Transmuted Generalized Inverse Weibull Distribution

Directory of Open Access Journals (Sweden)

Faton Merovci

2014-05-01

Full Text Available A generalization of the generalized inverse Weibull distribution the so-called transmuted generalized inverse Weibull distribution is proposed and studied. We will use the quadratic rank transmutation map (QRTM in order to generate a flexible family of probability distributions taking the generalized inverseWeibull distribution as the base value distribution by introducing a new parameter that would offer more distributional flexibility. Various structural properties including explicit expressions for the moments, quantiles, and moment generating function of the new distribution are derived. We propose the method of maximum likelihood for estimating the model parameters and obtain the observed information matrix. A real data set are used to compare the flexibility of the transmuted version versus the generalized inverse Weibull distribution.

Neutron dynamics of fast-spectrum dedicated cores for waste transmutation; Etude et amelioration du comportement cinetique de coeurs rapides a la transmutation de dechets a vie longue

Energy Technology Data Exchange (ETDEWEB)

Massara, S

2002-04-01

Among different scenarios achieving minor actinide transmutation, the possibility of double strata scenarios with critical, fast spectrum, dedicated cores must be checked and quantified. In these cores, the waste fraction has to be at the highest level compatible with safety requirements during normal operation and transient conditions. As reactivity coefficients are poor in such critical cores (low delayed neutron fraction and Doppler feed-back, high coolant void coefficient), their dynamic behaviour during transient conditions must be carefully analysed. Three nitride-fuel configurations have been analysed: two liquid metal-cooled (sodium and lead) and a particle-fuel helium-cooled one. A dynamic code, MAT4 DYN, has been developed during the PhD thesis, allowing the study of loss of flow, reactivity insertion and loss of coolant accidents, and taking into account two fuel geometries (cylindrical and spherical) and two thermal-hydraulics models for the coolant (incompressible for liquid metals and compressible for helium). Dynamics calculations have shown that if the fuel nature is appropriately chosen (letting a sufficient margin during transients), this can counterbalance the bad state of reactivity coefficients for liquid metal-cooled cores, thus proving the interest of this kind of concept. On the other side, the gas-cooled core dynamics is very badly affected by the high value of the helium void coefficient (which is a consequence of the choice of a hard spectrum), this effect being amplified by the very low thermal inertia of particle-fuel design. So, a new kind of concept should be considered for a helium-cooled fast-spectrum dedicated core. (authors)

Subcritical set coupled to accelerator (ADS) for transmutation of radioactive wastes: an approach of computational modelling

International Nuclear Information System (INIS)

Torres, Mirta B.; Dominguez, Dany S.

2013-01-01

Nuclear fission devices coupled to particle accelerators ADS are being widely studied. These devices have several applications, including nuclear waste transmutation and producing hydrogen, both applications with strong social and environmental impact. The essence of this work was to model an ADS geometry composed of small TRISO fuel loaded with a mixture of MOX uranium and thorium target material spallation of uranium, using methods of computational modeling probabilistic, in particular the MCNPX 2.6e program to evaluate the physical characteristics of the device and their ability to transmutation. As a result of the characterization of the spallation target, it can be concluded that production of neutrons per incident proton increases with increasing dimensions of the spallation target (thickness and radius), until it reached the maximum production of neutrons per incident proton or call the region saturation. The results obtained in modeling the ADS device bed kind of balls with respect to isotopic variation in the isotopes of plutonium and minor actinides considered in the analysis revealed that accumulation of mass of the isotopes of plutonium and minor actinides increase for subcritical configuration considered. In the particular case of the isotope 239 Pu, it is observed a reduction of the mass from the time of burning of 99 days. The increase of power in the core, whereas tungsten spallation targets and Lead is among the key future developments of this work

Transmutation and the Global Nuclear Energy Partnership

International Nuclear Information System (INIS)

Bresee, James

2007-01-01

, somewhat, the uranium ore and enrichment requirements at a given level of power production, but has the disadvantage of producing non-fissile plutonium isotopes and the so-called minor actinides (neptunium, americium and curium), some of which act as neutron poisons, and thus, require increasing uranium enrichment, eventually raising fuel costs beyond practical limits. The French only use one recycle of plutonium in their power reactors. The future 'burning' (transmutation by fission) of used plutonium (and the other transuranics) could, if put into large-scale practice, eliminate one of the more serious proliferation problems in the world today, the accumulation of large quantities of separated civilian plutonium. It is generally accepted by the world's technical community that the effective way to transmute transuranics is by fissioning them in a fast reactor (i.e., reactors not containing light materials used to slow down, by collision fission, neutrons in LWRs to velocities equal to thermal velocities or the media temperature). (author)