Effects of diesel fuel additives on engine performance and reliability. Part 2. Effects of lubricity additives; Keiyu tenkazai ga engine seino oyobi shinraisei ni ataeru eikyo. 2. Junkatsusei kojo ni yoru eikyo

Energy Technology Data Exchange (ETDEWEB)

Matsudaira, J; Okada, M; Naruse, H [Toyota Motor Corp., Aichi (Japan)

1997-10-01

Many studies about the effects of lublicity additives for diesel fuel have been carried out and reported. These additives have already been used in Europe, north-America for couple of years and it has just started in Japanese market this July. This paper mainly describes the effects of lublicity additives on engine performance and reliability. At first, the effects on engine reliability were investigated during 30 thousand kms chasis dynamometer test. Secondary, the effects on piston ring corrosion, injection nozzle fouling and water separation were investigated. Furthermore, 70 thousand kms engine reliability test was conducted, and investigated some component parts. 2 refs., 10 figs., 4 tabs.

Study on the creation of biopolymer materials under micro-gravity; Bisho juryokuka deno seitai kobunshi zairyo no sosei kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

In order to create new functional organic thin film materials, basic data were examined under micro-gravity. Polymerization of pyrrole was affected by micro-gravity after a few minutes from the beginning of reaction. Although relatively uniform particles were obtained, the particle size was finely dependent on conditions. Electrolytic polymerization of conductive organic thin films was yet unstable in reproducibility. On orientation control and thin film formation of protein under gravity-free environment, electrodeposited films were obtained using bacteriorhodopsin film suspension by applying voltage of 6.4V for 9s after 1s from falling. The reproducibility of the number and area of molecular layers was poor. On the study on the formation process of organic thin films, creation of homogeneous films is probably possible by filtration from suspension under reduced pressure under micro-gravity for a short time. Trial linear polymer tied in a row was obtained by capillary injection of dense polymer solution. The viscous fingering phenomenon of viscoelastic bodies under micro-gravity was compared with that on the ground. 11 refs., 36 figs., 1 tab.

Environmental control by biotechnology and ecotechnology, construction of ecopolis. Seibutsu kogaku-seitai kogaku to kankyo joka, Ecopolis no soshutsu

Energy Technology Data Exchange (ETDEWEB)

Mori, T [Shimane Univ., Shimane (Japan). Faculty of Agriculture

1992-09-01

The relationship between environmental control and biotechnology is discussed, and purification of moats and lakes is taken up as a concrete example of introducing biological waste water treatment technology to ecotechnology. In addition, an overall waste disposal system connecting cities and agricultural districts is investigated. After the purification of water and waste problem solution, etc. are discussed, the importance of creating ecopolis and ecotown is described. The 3 concepts of microbial ecotechnology (high densification of organism, field control, interaction between organisms) are used to explain biological treatment technology. Attempts for direct purification and ecotechnology are described quoting a few examples. If waste produced in cities and ligneous materials or charcoal obtained from forests are mixed for treatment, effective waste treatment or new resources production may be possible. It seems to be possible to create ideal ecopolis and ecotown by applying the doctrine of irrigation, drainage and reclamation engineering and the technology established by now. 35 refs., 1 fig., 2 tabs.

Effect of water pollution on marine organisms; Sekiyu osen no kaiyo seibutsu eno eikyo hyoka

Energy Technology Data Exchange (ETDEWEB)

Ogata, M. [Okayama Univ., Okayama (Japan); Fujisawa, K. [Okayama Prefectural Fisheries Experiment Station, Okayama (Japan)

1997-10-10

Toxicity of petroleum component to aquatic organisms appears as a result of its deposition onto living organisms followed by its migration into bodies of the organisms, and emergence of toxicity from the migrated component. Effect evaluation processes standing on this viewpoint may include the exposure monitoring or migration monitoring, in which the petroleum component migrated into marine organisms is analyzed and the state of the component concentrated in these organisms is measured, or effect monitoring, in which actions of the petroleum component in the organisms are investigated. The effects of petroleum on aquatic organisms would include the following occurrence: direct fatal toxicity acting on cells and membranes, quasi-fatal toxicity causing death indirectly through feeding actions and abnormal actions, direct coating of oil on surface of organisms, which prevents movability and feeding actions of the organisms and reduces hydrophilicity of plumes and hairs, pollution of living organisms due to migration of carcinogenic aromatic compounds into bodies of the living organisms, and change in species compositions and geographic distribution of living organisms due to change in physico-chemical environment. This paper explains cases of detection and identification of organic sulfur compounds, aromatic compounds, polycyclic aromatic compounds, paraffins, olefins and heavy metals in parametric compounds of petroleum. 20 refs., 4 figs., 3 tabs.

Effect of fluid-filled boreholes on resistivity tomography; Hiteiko tomography ni okeru konaisui no eikyo

Energy Technology Data Exchange (ETDEWEB)

Sugimoto, Y [DIA Consultants Co. Ltd., Tokyo (Japan)

1997-10-22

Theoretical discussions were given on the effect of fluid-filled boreholes on resistivity tomography. The discussions performed incorporation of earth resistance as a method to consider borehole diameters in an FEM calculation using wire elements. The numerical experiment conducted a simulation on the following two objects: resistivity tomography in a horizontal multi-layer structure consisted of layers with resistivity ranging from 10 to 10000 ohm-m, and a model with a slanted low resistivity band existing in a background of 5000 ohm-m. As a result of the discussions, it was made clear that the effect of the boreholes can be corrected by giving earth resistance between the wire elements and natural ground. An improved potential calculating program indicated that the effect of the fluid-filled boreholes in the resistivity tomography generates false images with high resistivity along the bores if the resistivity has high contrast. Incorporating the wire elements into an inverse analysis model reduces the false images and improves the accuracy. 1 ref., 12 figs.

Influence of life line stoppage on building equipments; Lifeline tozetsu no kenchiku setsubi eno eikyo

Energy Technology Data Exchange (ETDEWEB)

Sadohara, S. [Yokohama National University, Yokohama (Japan). Faculty of Engineering

1995-06-05

Our daily life is being supported by electricity in various ways. This paper, explains the influence of the stoppage of the electricity, affecting infrastructures, buildings and people`s daily life based on the survey result of a long term electricity stoppage in Hiroshima City in September 1991. This paper also introduces the survey result of emergency generators operation in Japan and in the U.S. Last, the ways and ideas to make lifeline reliability higher in the future are summarized. 1 ref., 11 figs., 7 tabs.

Effects of organophosphoric acid triesters on human health; Yuki rinsan toriester rui no kenko eikyo

Energy Technology Data Exchange (ETDEWEB)

Hirose, A. [National Institute of Hygienic Sciences, Tokyo (Japan)

1996-09-10

This paper describes the effects of organophosphoric acid triesters (OPEs) on human health. Tri-o-cresyle phosphate is metabolized in vivo, and forms neurotoxic esterase hindrance substance. More neurotoxic substance is formed by introduction of hydroxyl group into methyl group and cyclization. The toxicity is largely dependent on kinds of animals and individuals. Tris-(2,3-dibromopropyl) phosphate, trimethyl phosphate and tris-(2-ethylhexyl) phosphate give a carcinogenesis to experimental animals. In order to evaluate the effect of detected OPE concentrations in actual environment on human health, the genotoxicity of OPEs should be determined. In the case of no genotoxicity, the allowable intake of OPEs is determined by multiplying a safety factor by NOEL obtained from animal experiment. In the case of clear genotoxicity, the allowable intake is determined by model calculation. Although the toxicity of simple OPE is weak, the synergistic effect of multiple exposure is yet unidentified. 23 refs., 2 figs., 1 tab.

Study on the advanced orientation control technology of biopolymers; Seitai kobunshi zairyo no kodo haiko hairetsu seigyo gijutsu no kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Creation of new functional organic materials for the medical application has been investigated under the microgravity. Facilities of the Japan Microgravity Center were used for this study. For the high-speed synthesis of uniform polymer particles under the microgravity condition for ten seconds, appropriately good results were obtained in the oxidation polymerization of pyrroles. For the synthesis of organic conductive thin films by the electrolytic polymerization, the resistance of electrolyte became larger in the microgravity field. It was required to set conditions so as to enhance the effects of microgravity environment. For the orientation control and thin film formation of proteins, the bacteriorhodopsin was examined. It was found that the microgravity improved the quality of electrocoatings. When the surface tension and viscosity of coating liquid were appropriately controlled under the microgravity, thin films were able to be prepared by utilizing a change from 1g to {mu}g. When the high viscosity fluid is placed in the artificial two-dimensional space composing of two parallel plates, and the low viscosity fluid, such as air, is injected into the above, the interface grows in the finger shaped pattern, namely, viscous fingering. The influence of gravity on this phenomenon was also investigated. 11 refs., 45 figs., 5 tabs.

Comprehensive research cooperation in environmental technology in fiscal 1995; 1995 nendo kankyo gijutsu sogo kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Cooperative study was conducted on research subjects concerning water pollution preventive technologies in China and Thailand. In China, straw pulp mills were studied which were in the Institute of Light Industry Environmental Protection and the Environmental Engineering Course of Jinghua University. The following studies were jointly conducted: survey of the water quality pollution caused by waste water, investigational study on production technology and waste water treatment technology, extraction of technologies effective to preserve water quality, study/evaluation of economical efficiency of the said technologies, etc. In Thailand, cooperative research was conducted on automatic measuring technology for factory waste water in a model industrial estate of the Thai National Industrial Estate Corporation. Items for the study were a study on measuring technology for water quality environment, an investigation on the status of water quality environment in the model industrial estate, a study on automatic measuring technology for plant waste water, a study on how to use measuring data in the model industrial estate, etc. Every study enabled technical data accumulation at every research institute through field research exchanges. 24 refs., 91 figs., 45 tabs.

Interactions between wall rocks around magma and hot water. Magma shuhen no hekigan/nessui sogo sayo

Energy Technology Data Exchange (ETDEWEB)

Fujimoto, K.

1992-12-01

This paper describes interactions between wall rocks around magma and hot water. The paper discusses effects of hydrothermal environments on dynamic properties of rock minerals with respect to hydrolytic weakening (decrease in dynamic strength of a mineral under presence of water) and reaction enhanced deformation (deformation accelerated by chemical change occurring in a mineral itself). It also explains chemical reactivity of minerals under hydrothermal enviroments with respect to four types of chemical changes in minerals, factors governing mineral dissolution rates, and importance of equilibrium and non-equilibrium in main components in reactions between minerals and waters. These statements quote mainly results of indoor experiments. The paper indicates the following matters as problems to be discussed on interactions between wall rocks around intrusive rocks and hot waters: Deviation from chemical equilibrium in reactions between rocks and waters; change in permeability as a result of reactions between rocks and waters; and possibilities of hydrolytic weakening in rocks around intrusive rock bodies. 52 refs., 6 figs.

Effect of groupware introduction on office works; Groupware donyu no white color gyomu e ataeru eikyo

Energy Technology Data Exchange (ETDEWEB)

Baba, K. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1996-05-01

Investments for information systems in Japanese firms have been shifting from those for main frame systems to PC, LAN and groupware systems. Described herein are effects of groupware introduction on office works, and efficient introduction and practical application of these systems. The groupware functions are divided into information sharing, analyzing, integrating and coordinating functions, and changed information transmission as a result of practical application of each function has been followed by literature and questionnaire surveys on experiences at advanced enterprises. The results indicate that the changes are represented by 6 patterns, from replacement of information media to changes in working styles. The major productivity-related effects brought by introduction of these systems are decreased document volumes and improved skills of employees. The notable effects on office works are improved efficiency resulting from allotting one personal computer to each employee and from introduction of E-mail systems which solve problems involved in telephone communication. 15 refs., 11 figs., 10 tabs.

Continuous measurement of electrical characteristics in plants. 3. Shokubutsu seitai no denki tokusei sokuteiho. 3. ; Suikoeki pH chosei heno tekiyo

Energy Technology Data Exchange (ETDEWEB)

Sekiyama, T; Haniyu, H; Saiki, H

1989-09-01

Controlling pH of nutrient solution and keeping the other conditions unchanged, measurements of variation in electric potential difference between leaf and hypocotyl of a bush bean plant was performed for about seven days. Silver electrodes 0.3mm in diameter were glued on the surface of the plant using conductive paste prepared by dissolving gelatine in Ringel {prime} s solution. The results obtained are summarized as follws: first, when pH of the solution is suddenly increased or decreased, the potential of leave becomes high or low with respect to that of hypocotyl respectively; second, the variation in potential difference between them is affected by the rate at which pH of the solution is adjusted, although the total variation of pH is controlled to be the same, and in particular by mild adjustment (0.02 - 0.05pH/min) it is reduced to 1/2 - 1/4 of that produced by sudden change; third, abrupt change in pH of the solution cause to the plant the temporary suppression of its water absorption having a duration of 7 - 15 minutes. A short account is given of a non-contact type measurement of bioelectric potential performanced by making use of a Faraday {prime} s cage. 11 refs., 12 figs.

Effect of ambient gas density for diesel spray; Diesel funmu ni taisuru fun`iki mitsudo no eikyo

Energy Technology Data Exchange (ETDEWEB)

Yokohashi, M; Suzuki, T; Oshima, R [Tohokugakuin University, Sendai (Japan); Ono, A [Shinryo Corp., Tokyo (Japan)

1997-10-01

Effect of ambient gas density for fuel spray are measured to investigate the Diesel spray behavior. The change of ambient gas density has been given by pressuring N2 gas and using a high density atmospheric pressure SF6 gas. The measurement are performed for the spray penetration and angle. As a result, the spray penetration is confirmed same tendency at the change of density by pressuring N2 and using SF6. Though spray angle is required modification with viscosity. 2 refs., 11 figs.

Report on survey in fiscal 1999. Comprehensive survey on medical appliances; 1999 nendo iryo kiki sogo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The environment around medical treatment in Japan is changing greatly in recent years, because of aging of the population, increase in life habit diseases, and progress in medical science and technologies. In addition, the needs of people are on the trend of diversification. Furthermore, as a result of the information communication field gaining remarkable power, people can obtain information in various forms, and are acquiring chances of learning various kinds of knowledge about medical treatment. Thus, scenes to respond to demands of patients are increasing more than ever in medical activities. On the other hand, works and conversion in providing efficient medical services are sought because of pressures on medical finance. Therefore, the 'medical and welfare device development project' was launched in fiscal 1994, wherein NEDO has been promoting the research and development jointly with private business entities. In fiscal 1999, assignments in important technologies will be made clear taking the future into the sight on three themes in two fields of developing low invasive operation systems, and comprehensively developing artificial organ technologies. Themes to be developed newly in the future will be selected, and the contents of the research and development thereon and the ways it should be will be investigated, evaluated and discussed specifically. (NEDO)

Photovoltaic power generation field test at Industrial Technology Research Institute. Prefectural office building in a sunshine-rich district (Kanagawa Prefectural Industrial Technology Research Institute); Sangyo gijutsu sogo kenkyusho taiyoko hatsuden field test jigyo (nissha ryoko chiku no kenchosha). Kanagawaken sangyo gijutsu sogo kenkyusho

Energy Technology Data Exchange (ETDEWEB)

Okazaki, H [Kanagawa Prefectural Government Office, Yokohama (Japan)

1997-05-30

The result of a photovoltaic power generation field test in fiscal 1996 on a prefectural office building in a sunshine-rich district is reported. It is a lighting power source installed in fiscal 1994 on the third-floor rooftop of the management information building of Kanagawa Prefectural Industrial Technology Research Institute. It has a capacity of 25kW, operating on system interconnection (no back flow), and has a single 15-series/26-parallel array (mono-crystal modules) facing 38deg westward from due south and inclined at an elevation angle of 20deg. From the 240000kWh insolation that contributed to power generation, a DC power output of 28000kWh was obtained, output of 25000kWh after conversion into AC. The module efficiency was 10.8-13.8%, higher when the daily mean temperature was lower. In the case of 3kW type expected to diffuse into the residential and commercial sector and household sector, one will output 3000kWh a year, which is an appropriate capacity as a locally distributed type power generating system in view of the monthly consumption of 2000kWh by a household in general in the Tokyo Electric Power Co., Ltd. service area. No problem is found in reliability of the tested system. Although the power it generates is less than what this office consumes, it is effective in enlightening people about resources saving and peak cut in summer

FY1995 bio-information monitoring microsystems for human health care; 1995 nendo kenko kanri wo mokutei to shita seitai joho keisokuyo micro system

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-31

Long term and continuous monitoring of health parameters have been expected for patient monitoring, human health care and sick prevention. Bio-information monitoring microsystems which can send personal health information to the doctor in the hospital at any time through mutual data communication networks. A prototype of the very low-power consumption wireless systems for monitoring ECG (Electrocardiogram) was fabricated and tested. It consists of an ECG detector/transmitter located at the chest and a relay transmitter placed at the wrist. Data communication between them is obtained with very low-power signal transmission by AC micro current flown through the tissue of the body. A prototype of a multi sensor chip for biosensing micro capsule was also fabricated and tested. It consists of a piezo resistive diaphragm pressure sensor, a pH ISFET (Ion Sensitive Field Effect Transistor) and a p-n diode temperature sensor. To realize reliable medical telemetry in severe electromagnetic environment, spread spectrum communication to ECG data method was applied. This method is very useful for the data communication of bio-information monitoring microsystems. (NEDO)

Ecological processes for Environmental Impact Assessment in Coastal Waters; Engan no kankyo eikyo hyoka (EIA) eno seitaigakuteki apurochi

Energy Technology Data Exchange (ETDEWEB)

Ishikawa, Kimitoshi. [Environmental Assessment Dept., Tokyo (Japan)

1999-03-25

This paper focuses on a method for estimating adverse effects on natural environment by economic development in coastal waters in Japan. In particular, the most critical relations concerning the impact on marine organisms is pointed out and discussed according to an environmental impact assessment. Relations between environmental impact assessment and marine organisms needs a quantitative ecological approach in order to succeed in sustainable development of coastal waters management. Recently, the Environment Agency of Japan pointed out the unreliability and the theme on accuracy and the staff for biology and ecology in the environmental impact study. Ecological response to environmental impact occurs in a wide spectrum of physiological and biological and biological functions. Therefore biological monitoring measures must correspond to the given time-space scale of natural mechanisms. For the evaluation of environmental impact, it is desire able to develop of experimental technics and collect biological and ecological basic data for the object. I Reconstructing the following: 1. Reconstructing a clearlistic EIA process by EIA agencies and practitioners, 2. Scorping the biological and ecological issues by EIA professionals, 3. Using the current computer technology, 4. Considering monitoring systems over scales of time and space for the ecological target and 5. Making available to public all monitoring data and reports of EIA. (author)

Influence of traffic situation on a driver`s visual behavior; Kotsu jokyo ga shinin kodo ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Kisumi, E; Hara, t [Mitsubishi Motors Corp., Tokyo (Japan)

1997-10-01

When a driver performs an in-car visual task, that task must be time-shared with the driving task. Therefore, his/her glances would be divided between the forward view and the in-car visual display in accordance with traffic situation. In order to investigate the influence of traffic situation on glance duration distribution, an experiment for in-car visual task was conducted using Mitsubishi`s flat-belt driving simulator. As a result, a glance duration tends to shorten as driving task demands increase, such as driving at high speed, being overtaken, etc., and a glance cycle tends to shorten under the same situation. 5 refs., 8 figs., 1 tab.

Report on the comprehensive investigational research (at-home welfare apparatus system); Sogo chosa kenkyu (zaitaku fukushi kiki system) hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

An investigational study was conducted on the research and development of an at-home welfare apparatus system. In this study, a stay experiment was carried out on whether aged or handicapped people can easily live in welfare houses into which at-home welfare apparatus was integrated, using high-tech at-home nursing apparatus systems (welfare techno house: WTH) which were installed at seven places in Japan based on `the development of a system supporting independent excretion.` In addition, the following were conducted: experiments on at-home welfare apparatus in terms of the evaluation of performance/operability/safety, physical physiology reactions, nursing burden/estimate of independence, two-way communication, examination of housing environments, etc. In WTH Chofu, a test on evaluating welfare apparatus was conducted by people with limbs paralysis and healthy case workers. In WTH Sapporo, by a working group studying biological information, examinations were made on the situation of standing up of healthy adults, old people and people with paralysis of one side of the body from various types of chairs, beds, wheel chairs, portable toilets and sitting down on them. An examination was also made on harmony with psychological function and physically adaptable function by a working group studying at-home nursing apparatus. 75 figs., 15 tabs.

Microalgal biotechnologies for recycling of pollutants; Tayona sorui kino wo kiban to suru seibutsuken busshitsu junkangata sogo saishigenka gijutsu

Energy Technology Data Exchange (ETDEWEB)

Miyamoto, K; Nasu, M; Hashimoto, C; Tanaka, K; Hirata, M [Osaka University, Osaka (Japan). Faculty of Pharmaceutial Science; Fujita, M; Takagi, M [Osaka University, Osaka (Japan). Faculty of Engineering; Hirata, Y; Taya, M [Osaka University, Osaka (Japan). Faculty of Engineering Science; Yamanishi, H [Osaka University, Osaka (Japan). Faculty of Medicine

1997-02-01

This paper describes the technology development by which biomass is produced by treatment of pollutants using microalgae, and is recycled. A bioreactor system has been developed, in which microalgal biomass can be obtained through the effective treatment of CO2 and NOx using microalgae having ability of increase under the severe condition with simultaneous flow of CO2 and NOx. A new method has been also developed for separating and recovering the microalgae. Materials, such as glucose, glycerol, acetic acid, and lactic acid, were produced from the obtained biomass through physico-chemical and biological treatments. These materials can be converted into ethanol and hydrogen. For this treatment and recycling system, functions as a part of natural material recycling were considered to be most significant. Development of an analysis and evaluation method of an impact of this system on the natural environment is also tried. 1 fig.

FY1995 new technology of artificial organ materials which can induce host biocompatibility; 1995 nendo jinko zokiyo seitai kino fukatsukagata sozai no kaihatsu gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-12-01

The aim of this project is to produce a highly biocompatible materials for next generation's artificial organs using the following methods: 1, Micromodification of polymer materials. 2, Biocompatible treatment for biological materials. 3, Application of bioabsorbable materials. 4, Bioactive substance immobilization. and 5, Use of autologous tissue as artificial organ materials. As a synthetic polymer material, microporous polyurethane was used for a small diameter vascular prosthesis. The graft with this technology was successfully implanted in rat abdomical aortic position. The graft of 1.5 mm in internal diameter and 10cm in length showed excellent patency with nice endothelialisation. As a biological material, microfibers of collagen was used for a sealing substance of vascular prothesis. The microfibers absorbed a large amount of water, which could prevent blood leakage from the graft wall. The graft showed non-thrombogenic property and excellent host cell affinity, resulted in rapid neointima formation. As to autologous tissue, bone marrow was used, since marrow cells can differentiate into any mesenchimal cells with synthesis of growth factors. Marrow cell transplanted vascular prothesis showed rapid capillary ingrowth. These results indicated that the newly designed materials had suitable properties for materials of next generation's artificial organs. (NEDO)

FY1995 new technology of artificial organ materials which can induce host biocompatibility; 1995 nendo jinko zokiyo seitai kino fukatsukagata sozai no kaihatsu gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-12-01

The aim of this project is to produce a highly biocompatible materials for next generation's artificial organs using the following methods: 1, Micromodification of polymer materials. 2, Biocompatible treatment for biological materials. 3, Application of bioabsorbable materials. 4, Bioactive substance immobilization. and 5, Use of autologous tissue as artificial organ materials. As a synthetic polymer material, microporous polyurethane was used for a small diameter vascular prosthesis. The graft with this technology was successfully implanted in rat abdomical aortic position. The graft of 1.5 mm in internal diameter and 10cm in length showed excellent patency with nice endothelialisation. As a biological material, microfibers of collagen was used for a sealing substance of vascular prothesis. The microfibers absorbed a large amount of water, which could prevent blood leakage from the graft wall. The graft showed non-thrombogenic property and excellent host cell affinity, resulted in rapid neointima formation. As to autologous tissue, bone marrow was used, since marrow cells can differentiate into any mesenchimal cells with synthesis of growth factors. Marrow cell transplanted vascular prothesis showed rapid capillary ingrowth. These results indicated that the newly designed materials had suitable properties for materials of next generation's artificial organs. (NEDO)

FY1995 new technology of artificial organ materials which can induce host biocompatibility; 1995 nendo jinko zokiyo seitai kino fukatsukagata sozai no kaihatsu gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-05-01

The aim of this project is to produce a highly biocompatible materials for next generation's artificial organs using the following methods: 1, Micromodification of polymer materials. 2, Biocompatible treatment for biological materials. 3, Application of bioabsorbable materials. 4, Bioactive substance immobilization. and 5, Use of autologous tissue as artificial organ materials. As a synthetic polymer material, microporous polyurethane was used for a small diameter vascular prosthesis. The graft with this technology was successfully implanted in rat abdomical aortic position. The graft of 1.5 mm in internal diameter and 10 cm in length showed excellent patency with nice endothelialisation. As a biological material, microfibers of collagen was used for a sealing substance of vascular prothesis. The microfibers absorbed a large amount of water, which could prevent blood leakage from the graft wall. The graft showed non-thrombogenic property and excellent host cell affinity, resulted in rapid neointima formation. As to autologous tissue, bone marrow was used, since marrow cells can differentiate into any mesenchimal cells with synthesis of growth factors. Marrow cell transplanted vascular prothesis showed rapid capillary ingrowth. These results indicated that the newly designed materials had suitable properties for materials of next generation's artificial organs. (NEDO)

FY1995 new technology of artificial organ materials which can induce host biocompatibility; 1995 nendo jinko zokiyo seitai kino fukatsukagata sozai no kaihatsu gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-05-01

The aim of this project is to produce a highly biocompatible materials for next generation's artificial organs using the following methods: 1, Micromodification of polymer materials. 2, Biocompatible treatment for biological materials. 3, Application of bioabsorbable materials. 4, Bioactive substance immobilization. and 5, Use of autologous tissue as artificial organ materials. As a synthetic polymer material, microporous polyurethane was used for a small diameter vascular prosthesis. The graft with this technology was successfully implanted in rat abdomical aortic position. The graft of 1.5 mm in internal diameter and 10 cm in length showed excellent patency with nice endothelialisation. As a biological material, microfibers of collagen was used for a sealing substance of vascular prothesis. The microfibers absorbed a large amount of water, which could prevent blood leakage from the graft wall. The graft showed non-thrombogenic property and excellent host cell affinity, resulted in rapid neointima formation. As to autologous tissue, bone marrow was used, since marrow cells can differentiate into any mesenchimal cells with synthesis of growth factors. Marrow cell transplanted vascular prothesis showed rapid capillary ingrowth. These results indicated that the newly designed materials had suitable properties for materials of next generation's artificial organs. (NEDO)

Influence of oil starvation on piston ring oil film thickness; Junkatsuyu kyokyuryo fusoku ga ring yumaku ni ataeru eikyo

Energy Technology Data Exchange (ETDEWEB)

Hiruma, M [Musashi Institute of Technology, Tokyo (Japan). Hydrogen Energy Research Center; Takiguchi, M [Musashi Institute of Technology, Tokyo (Japan)

1997-10-01

An analytical behavior of the piston ring oil film has been carried out theoretically under the condition where sufficient lubrication oil dose not exist. Phenomena have been studied on the oil film when plural rings slide together on the surface of cylinder with a new concept in addition to the well-known assumptions. In particular, a comparison has been made on the friction force with the data obtained by the floating liner method. 5 refs., 9 figs.

Loading test of pile affected by soil layer deformation; Jiban henkei no eikyo wo ukeru kui no saika jikken

Energy Technology Data Exchange (ETDEWEB)

Kakurai, M.; Tsuchiya, T. [Takenaka Corp., Osaka (Japan)

1997-10-10

Large soil tank developed for shearing experiments is used to study the horizontal movement of piles in earthquakes. The system comprises a soil filled (8m deep) tank, pile head loading jig, and 6 actuators. The soil tank is fabricated of 40 layers of 20cm-high iron frames of inner dimensions 2.5mtimes2.5m, and it is filled with soil that is to simulate the ground. The frames are divided into 4 groups each containing 10 frames, and the frames in each group are coupled with each other, so that all the frames in one group will move horizontally when the topmost frame in the group is moved horizontally. An actuator, which travels horizontally ganging with a computer, is mounted on the top frame in each group, and this setup enables the arbitrary simulation of ground deformation in the horizontal direction in an earthquake. The pile head loading jig, driven by 2 actuators, can keep restraining the pile head from rotation while applying load or deforming force to the pile head as desired in the vertical and horizontal direction. Experiments conducted using this system involve the force imposed on a pile in the soil tank by ground deformation and the resultant pile behavior including breakdown. 9 figs.

Improvement of motor inertia influence of electric power steering; Dendoshiki power steering no motor kansei no eikyo to hosho

Energy Technology Data Exchange (ETDEWEB)

Takehara, S; Sakamoto, K; Hanamoto, Y [Mazda Motor Corp., Hiroshima (Japan); Noritsugu, T [Okayama University, Okayama (Japan)

1997-10-01

Motor inertia of electric power steering affects not only steering characteristics but vehicle dynamics. We have investigated the influence of motor inertia and proposed a feedback strategy to compensate it. Weight of the test vehicle is 1100Kg and the steering system is pinion type electric power steering. By using simulation model and vehicle test, we have realized natural steering maneuvering and stable vehicle dynamics. 4 refs., 11 figs.

New Shinkansen operation management and control systems for Tohoku-Joetsu Shinkansen; Tohoku Joetsu Shinkansen no atarashii Shinkansen sogo system `COSMOS`

Energy Technology Data Exchange (ETDEWEB)

Otsuki, K. [East Japan Railway Co., Tokyo (Japan); Koda, K.; Uchimura, T.; Okazaki, S.; Imagawa, T.; Kawaguchi, K. [Hitachi, Ltd., Tokyo (Japan)

1997-02-01

Computerized Safety, Maintenance and Operation Systems of Shinkansen (COSMOS) has been developed to properly deal with the diversification and modernization of Shinkansen business and the improvement of its system. To avoid the concentration of duties and loads on any part of the system, the system functions are distributed into eight subsystems, which respectively cover transportation planning, operation management, maintenance work management, power system control, rolling stock management, centralized information management, facilities management, and yard operation management. The COSMOS is a huge system distributed across a large area whose 500 computers and terminals located in the eight subsystems and offices related with Shinkansen are linked by a network. A concept of autonomy and distribution is introduced into the system so that the impact on the others will be kept to the minimum in case some subsystems come to a stop. The new system is excellent in maintainability, flexibility, and extendability, and its operation room is quite compact. The COSMOS has been working smoothly since the beginning of its service, contributing to the modernization of Shinkansen business, such as rapid restoration in case of timetable disturbance, reduction in station workload, improved passenger guidance service, and centralization of section control business. 5 refs., 2 figs.

Report on a comprehensive research study (home welfare apparatus system - interface); Sogo chosa kenkyu (zaitaku fukushi kiki system - interface) hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

In the light of the increasing role of welfare at home with the advance of the aging society, the paper conducted an investigational study on the R and D of the home welfare apparatus system - interface. In the study, making the most of the leading home care apparatus systems (welfare technohouses) installed at seven places in the country, the paper carried out a stay experiment on how the life is in the welfare house into which home welfare apparatus is integrated, and an experiment to assess biological data on aged people. Especially as to the support apparatus used for smooth life motions in houses such as movement, excretion and bathing, examined were the linkage with house bodies, care apparatus used, mutual interface with welfare apparatus, etc. By the experiments to assess these home welfare apparatus, an analytical study was conducted on the points to be improved in welfare apparatus and housing equipment, and at the same time on the course of the research/development. Concerning a system for the research study, a research promotion committee was established in Technology Research Association of Medical and Welfare Apparatus, the members of which are learned persons from the industrial circle, the government and universities. 111 figs., 36 tabs.

Report on the development/comprehensive research of new hydrogen energy demonstrative technology; Shinsuiso energy jissho gijutsu kaihatsu sogo kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-06-01

In this project, the excess heat phenomenon caused by electrolyzing heavy water using palladium metal, etc. as electrode was captured as `new hydrogen energy.` To make a possibility of being as a future energy source clear, the abnormal heating phenomenon was verified. By elucidating the mechanism, the paper aimed at quantitatively controlling the heat generation. The R and D period was four years from fiscal 1993, and the details of the research are about the excess heat measuring test, material analysis/development tests, test on detection of reaction products, information collection/arrangement, international research cooperation. As a result of the research, a part of the excess heat measurement was surely able to be reproduced. However, when a confirmation experiment on the excess heat was conducted by another more positive method under the same conditions, it was found that the excess heat quantity was not the absolute excess heat quantity exceeding the measuring sensitivity/errors of the system. Supposing the excess heat of 0.1W order is generated in nuclear reaction, any of reaction products should be detected in a considerable quantity. However, no reaction products were not detected. 42 refs., 241 figs., 55 tabs.

Report on a comprehensive research study (home welfare apparatus system - lifestyle); Sogo chosa kenkyu (zaitaku fukushi kiki system - lifestyle) hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

An investigational study was conducted on evacuation of aged people at disaster, life maintenance, and welfare apparatus which is applicable to the future change of life style and its harmony with the living environment. In the study of care apparatus, reported were the apparatus operational interface using the indoor environmental control simulation system, safety on moving/transfer equipment, experiment on opening/closing power of sliding doors, study of electric-driven wheel chairs, study of the sitting pressure of various wheel chairs, etc. In relation to the living environment, the paper reported planning of houses introducing care apparatus, assessment of system kitchen, disaster prevention measures for aged/handicapped people, study on performance of the combined use in the living environment, assessment of drops in floor level in the living space, etc. Also reported were assessment on the living environmental control state of serious paralyzers of the limbs, study of a network to support care at home, etc. 48 refs., 117 figs., 29 tabs.

Evaluation on the effect of tsunami and seaquake on the floating structure; Tsunami kaishin no futai ni taisuru eikyo hyoka

Energy Technology Data Exchange (ETDEWEB)

Yoshida, K; Suzuki, H; Hosomi, I [The University of Tokyo, Tokyo (Japan); Nahata, H [The Long-Term Credit Bank of Japan, Ltd., Tokyo (Japan)

1997-12-31

The effects of tsunami and seaquake on large floating structures are theoretically studied, where these effects are followed in terms of local strength using the equation proposed by Sells to predict surface shapes changed by seaquake-caused uplift of the seabottom. The equation is combined with the one for tsunami propagation, to better predict the tsunami motion. The simulation results indicate the necessity of considering the effects of tsunami for the design of a large floating structure. The authors discuss that the effect of tsunami is minimized when a floating structure is set at a depth of at least 40 to 50m, chain length should be determined by equalizing the breaking weight with the load at which the structure starts to move, and a structure should be set at a position where it is not attacked by transverse waves. They also discuss that seaquake intensity should be predicted by the equation of motion of compressible fluid, and, noting local strength of a floating structure, it will not be damaged when it is at least 16mm thick under the conditions of 2m as seabottom uplift and 0.5m as draft depth. 15 refs., 9 figs., 2 tabs.

Influence of spectral solar radiation to the generating power of photovoltaic module; Taiyo denchi shutsuryoku eno taiyoko supekutoru eno eikyo

Energy Technology Data Exchange (ETDEWEB)

Minaki, S.; Ishihara, Y.; Todaka, T.; Harada, K. [Doshisha University, Kyoto (Japan); Oshiro, T.; Nakamura, H. [Japan quality Assurance Organization, Tokyo (Japan)

1997-11-25

As to the influence of spectral solar radiation to generating power of solar cells, a study was conducted from the aspects of season, time zone, intensity of solar radiation, etc. In the study, spectral responsive variation correction coefficients were introduced as evaluation values expressing the influence of spectral solar radiation. For the spectral distribution, an all sky spectral pyranometer by wavelength was used, and data were used which were obtained in the measurement in experimental facilities of the solar techno center. Concerning solar cell relative spectral sensitivity values, used were relative spectral sensitivity values of monocrystal and amorphous standard solar cells to the short-circuit current. Spectral response variation correction coefficients are coefficients correcting variations in conversion efficiency of solar cells due to changes in the spectral distribution. The changes of spectral responsive variation correction coefficients were studied using data obtained during April 1994 and March 1996. As a result, it was found that the coefficients showed large changes in summer and small ones in winter and that amorphous solar cells indicate this trend conspicuously. 3 refs., 6 figs., 3 tabs.

Evaluation on the effect of tsunami and seaquake on the floating structure; Tsunami kaishin no futai ni taisuru eikyo hyoka

Energy Technology Data Exchange (ETDEWEB)

Yoshida, K.; Suzuki, H.; Hosomi, I. [The University of Tokyo, Tokyo (Japan); Nahata, H. [The Long-Term Credit Bank of Japan, Ltd., Tokyo (Japan)

1996-12-31

The effects of tsunami and seaquake on large floating structures are theoretically studied, where these effects are followed in terms of local strength using the equation proposed by Sells to predict surface shapes changed by seaquake-caused uplift of the seabottom. The equation is combined with the one for tsunami propagation, to better predict the tsunami motion. The simulation results indicate the necessity of considering the effects of tsunami for the design of a large floating structure. The authors discuss that the effect of tsunami is minimized when a floating structure is set at a depth of at least 40 to 50m, chain length should be determined by equalizing the breaking weight with the load at which the structure starts to move, and a structure should be set at a position where it is not attacked by transverse waves. They also discuss that seaquake intensity should be predicted by the equation of motion of compressible fluid, and, noting local strength of a floating structure, it will not be damaged when it is at least 16mm thick under the conditions of 2m as seabottom uplift and 0.5m as draft depth. 15 refs., 9 figs., 2 tabs.

Integrated system technologies for water and sewage works. Information system technologies for rainwater drainage. Jogesuido sogo system gijutsu. Kou joho system

Energy Technology Data Exchange (ETDEWEB)

Shinohara, T; Nakada, M; Kondo, S [Toshiba Corp., Tokyo (Japan)

1994-05-01

The present report introduces the technological trend of rainwater drainage information system mainly with radar rain gauges. The information network must be strengthened as measures against the urban flood from the rainwater drainage. A radar rain gauge-based combination is needed of synthetic and organic processing technologies covering the traveling prediction of rainfall, data communication and rainwater drainage/flooding prediction. The correction method and data communication/display technology are explained for the measurement with radar rain gauges. In both correlation function method and rainfall area pursuit method, the traveling of rainfall is predicted by utilizing the radar information for the sewerage system. For the drainage analysis, it is necessary to quantitatively estimate the rainwater drained into both main and branch sewerage lines. It is made by preparing a rainwater drainage model. The quantitative estimation of rainwater drained into the branch sewerage lines calls for a revised Road Research Laboratory guidance by the Ministry of Construction. Supplemented with knowledge by veteran operators, the displayed image of pump operation support system is simulated for its verification. 2 refs., 3 figs.

Effect of heat treatment changes on swelling treatment of coal; Sekitan no bojun shori sayo ni oyobosu netsushori henka no eikyo

Energy Technology Data Exchange (ETDEWEB)

Satsuka, T.; Mashimo, K.; Wainai, T. [Nihon University, Tokyo (Japan). College of Science and Technology

1996-10-28

Discussions were given on effects of heat treatment at relatively low temperatures as a pretreatment for coal liquefaction on coal swelling and hydrogenolysis reaction. Taiheiyo coal was heated to 200{degree}C for one hour as a pretreatment. The attempted heating methods consisted of four steps of rapid heating (6.7{degree}C/min)quenching (20{degree}C/min), rapid heating/natural cooling (0.7{degree}C/min), heating (1.0{degree}C/min)/quenching, and heating/natural cooling. The swelling treatment was composed of adding methanol benzene into heat treated coal, and leaving it at room temperature for 24 hours. The hydrogenolysis was carried out by using a tetralin solvent and at an initial hydrogen pressure of 20 kg/cm{sup 2} and a temperature of 350{degree}C and for a time of one hour. Hydrogenolysis conversion in the heat treated coal was found lower than that of the original coal because of generation of liquefaction inactive components due to thermal polymerization. When the heat treated coal is swollen by using the solvent, gas yield from the hydrogenolysis reaction decreased due to gas suppression effect, and the conversion was lower than that of the original coal. Heat treatment suggests densification of the coal structure. Swollen coal shows no conspicuous difference in the heat treatment methods against the hydrogenolysis due to the swelling effect. 3 refs., 5 figs., 1 tab.

Effects of gasoline properties on exhaust emission and photochemical reactivity; Gasoline seijo ga haiki gas sosei, kokagaku hannosei ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Kumagai, R; Usui, K; Moriya, A; Sato, M; Nomura, T; Sue, H [Petroleum Energy Center, Advanced Technology and Research Institute, Tokyo (Japan)

1997-10-01

In order to investigate the effects of fuel properties on emissions, four passenger cars were tested under Japanese 11 and 10-15 modes using two series gasoline fuels. The test results suggest that the distillation property (T90) affects A/F ratio which in turn influences exhaust emissions. The results of regression analysis show that both ozone forming potential and air toxics are highly corrected with the composition of aromatic hydrocarbons in gasoline. 3 refs., 10 figs., 6 tabs.

Effects of MTBE blended diesel fuel on diesel combustion and emissions; MTBE kongo keiyu ga diesel nensho haiki ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Shundo, S; Yokota, H; Kakegawa, T [Hino Motors, Ltd., Tokyo (Japan)

1997-10-01

The effects of MTBE (Methyl-t-butyl ether) blended diesel fuel on diesel combustion and emissions were studied. In conventional diesel combustion, the testing mode was carried out in conformity with the Japanese 13 mode. Furthermore, this fuel was applied to a new combustion system (Homogeneous Charge Intelligent Multiple Injection). MTBE blended diesel fuel is more effective in the case of new combustion system and very low NOx, PM capability is suggested. 6 refs., 6 figs., 2 tabs.

Convenient methods for appreciating effects of acid rain on stone building materials; Sekizai ni taisuru sanseiu no eikyo hyokaho no kento

Energy Technology Data Exchange (ETDEWEB)

Katami, T.; Takahara, Y.; Nishikawa, H.; Kato, K. [Gifu Prefectural Health and Environmental Research Center, Gifu (Japan)

1996-05-10

A method to evaluate effects of acid rain has been investigated by exposing building marble plates at both outdoor and indoor sites and measuring lightness and roughness on the surface of plates. The lower pH of rain water fell, the more remarkable loss of lightness appeared in a short period on the surface of outdoor samples in one to three months exposure tests. As an appropriate negative correlation was shown between the lightness and the pH value, it was found that physical change of the plate surface can be estimated by using the lightness, optically measured value. For three to nine months indoor-exposure tests, difference of the lightness were quantitatively observed, but little differences of the roughness height were recognized among the different exposure sites. From the reduction of lightness on the marble plate surface exposed at outdoor and indoor sites, it was also found that damage levels of the marble plates were four to eleven times higher at outdoor sites by rain water than those at indoor sites by air pollutants, such as acid gases, in the ambient air. Thus, the optical method may be useful to evaluate damage levels of marble building materials caused by acid-rain water after exposing them for a relatively short period. 10 refs., 3 figs., 6 tabs.

Effect of oxygenated fuel on premixed lean diesel combustion; Kihaku yokongo diesel nensho ni oyobosu gansanso nenryo kongo keiyu no eikyo

Energy Technology Data Exchange (ETDEWEB)

Sasaki, S.; Miyamoto, T.; Harada, A.; Akagawa, H.; Tsujimura, K. [New ACE Institute Co. Ltd., Tokyo (Japan)

1998-05-01

Because injection timing in diesel engines is early in a premixed lean diesel combustion system using early fuel injection, ignition timing is determined by ignitability of the fuel used. The conventional diesel fuel, which has good ignitability, causes excessively early ignition, thus aggravating fuel consumption. In order to reduce cylinder temperature with an aim of delaying ignition timing to improve the fuel consumption, attempts are being made on using low cetane fuels to reduce CO2 gas supply or compression ratio, and to vary ignitability of the fuels. The present study investigated ignition timing control and properties of exhausts by mixing different types of oxygenated fuels into light oil. Mixing the oxygenated fuels into light oil proved that the ignition timing can be controlled, and mixing such low cetane fuels as ethanol and MTBE achieved improvement in fuel consumption. Trial use of the oxygenated fuels aggravated CO concentration, which is caused because the cylinder temperature was reduced. Numerical calculations suggest that use of fuels with faster evaporation speed and lower cetane number is effective in improving the fuel consumption and the exhausts. 12 refs., 9 figs., 2 tabs.

Effect of synthetic detergent and soap on the waste-water treatment. Gosei senzai oyobi sekken no haisui shori ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Inamori, Y. (national Institute for Environmental Studies, Tsukuba (Japan)); Takamatsu, Y. (University of Tsukuba, Tsukuba (Japan))

1993-05-01

This paper describes the effect of surfactants on purification capability and living life phases in the living life membrane method and the activated sludge method as biological waste water treatment methods. As a result of treating artificial waste water in an immersion hearth process of the living life membrane method, it was found that LAS added concentration at 50 mg/l or higher would not affect noticeably the quality of water treated under a steady-state operation, but that at 100 mg/l has aggravated the treated water quality by increasing COD. In the case of soaps, the COD in the treated water has aggravated when the added concentration is 70 mg/l or higher. The result of discussing the activated sludge process using urban sewage water indicated that COD in the treated water shows higher value for synthetic detergents than for soaps at the detergent added concentration of 140 mg/l or higher, having affected adversely the treated water quality. An activated sludge treatment process was operated to identify the effects of synthetic detergents and soaps on living life phases in the activated sludge and living life membranes. The result suggests that either the LAS added system or the soap added system presents no problems in a long-time aeration, while activated sludge aerated for the standard period of time has a possibility of abnormally proliferating filamentous microorganisms that can cause bulking in the soap system. 14 refs., 3 tabs.

Influence of smectites on resistivity of rocks and soils; Smectite nendo kobutsu ga ganseki dojo no hi teiko ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Takakura, S; Nishizawa, O; Aoki, M [Geological Survey of Japan, Tsukuba (Japan); Kozake, K [University of Tsukuba, Ibaraki (Japan)

1996-10-01

This paper illustrates the measurement results of resistivity for specimens including smectite clay minerals artificially synthesized, and also discusses the influence of smectites on resistivity. Three kinds of bentonites, i.e., KN-1, Kawasaki ore, and Kawasaki Sanhaku, were used for preparing smectites. The KN-1 is Na type smectite, the Kawasaki ore is Ca type smectite, and the Kawasaki Sanhaku is acid clay. It is well known that smectites lower the resistivity of rocks. However, the experimental results suggested that the degree of decreasing the resistivity depends on the kind of smectites. The effect of decreasing the resistivity by the KN-1 was much superior to the other smectites. For the KN-1, a thick electrical double layer was formed by Na ions in the interlayers, which resulted in the larger effect of decreasing the resistivity. Swelling capacity and cation exchange capacity (CEC) of the KN-1 were large, which agreed with the above mentioned consideration. Reversely, it was considered that smectites having larger effect of decreasing the resistivity exhibited larger swelling capacity and CEC. 4 refs., 3 figs.

Effect of PV module output power on module temperature; Taiyo denchi no shutsuryoku henka ga module hyomen ondo ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Hongo, T; Kitamura, A [Kansai Electric Power Co. Inc., Osaka (Japan); Igaki, K; Mizumoto, T [Kanden Kako Co. Inc., Osaka (Japan)

1996-10-27

Effect of the photovoltaic (PV) module output power variation on the module surface temperature has been investigated by field measurements. PV modules with capacity of 54 W were used for the temperature measurements. Three 2 kW-class PV systems were operated. T-type thermocouples were used for measuring temperatures. Measurement time intervals were 15 minutes, 30 minutes, 60 minutes, and 24 hours. Measurement period was between May 25, 1995 and June 25, 1996. The surface temperature increased during non-loaded PV output, and decreased during load-carrying PV output. Difference of the surface temperature between non-loaded PV output and load-carrying PV output was 3.5{degree}C at maximum through a year. The surface temperature was saturated within 30 minutes. When PV output was changed in 30 or 60 minutes interval, the variation of surface temperature was distinctly observed. When PV output was changed in 15 minutes interval, it was not observed distinctly. There was no difference of the surface temperatures during the time zones with less solar radiation, such as in the morning and evening, and at night. Except these time zones, difference of the surface temperatures was 3.5{degree}C at maximum. 4 figs.

Psychological influences for the driver by the changes of running circumstance; Jidosha no soko kankyo henka no driver eno shinriteki eikyo

Energy Technology Data Exchange (ETDEWEB)

Okura, S; Yokomori, M; Yamaguchi, S [Meijo University, Nagoya (Japan)

1997-10-01

A driver is influenced psychologically by the cars proceeding on the street and the cars parked on the shoulder which come into the front view. The traffic accidents are caused when these influences put a lot of stress on a driver. In this report, we study the relations between the road traffic condition on the streets and the highway and the driver`s psychological and psysiological responses by using the driver`s front view, sweating and pulse rate. 6 refs., 8 figs.

Advancing aging society and its effect on the residential use energy demand; Shintensuru koreika shakai to kateiyo energy juyo eno eikyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-07-01

The paper analyzed various factors regulating the energy demand in aged households and viewed the future residential use energy demand in the aging society. In Part 1, based on the family budget survey annual report, a study was made of the energy consumption situation of aged people and the trend of the future residential energy consumption. In Part 2, a study was conducted based on survey data on the U.K., France, Sweden and Denmark. In Western countries which are the developed countries of aging, the energy conservation policy effectively worked for the space heating demand which is highest of all, and factors of the energy consumption increase by aging were absorbed. However, since in Japan, aging is rapidly advancing and further there are relatively more factors which connect to an increase in energy consumption in aged households as compared with Western countries, it is thought that Japan is in a situation where the energy consumption increases more often, influenced by aged households. 91 refs., 130 figs., 41 tabs.

Interim evaluation report of the mutually operable database systems by different computers; Denshi keisanki sogo un'yo database system chukan hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1989-03-01

This is the interim report on evaluation of the mutually operable database systems by different computers. The techniques for these systems fall into four categories of those related to (1) dispersed data systems, (2) multimedia, (3) high reliability, and (4) elementary techniques for mutually operable network systems. The techniques for the category (1) include those for vertically dispersed databases, database systems for multiple addresses in a wide area, and open type combined database systems, which have been in progress generally as planned. Those for the category (2) include the techniques for color document inputting and information retrieval, meaning compiling, understanding highly overlapping data, and controlling data centered by drawings, which have been in progress generally as planned. Those for the category (3) include the techniques for improving resistance of the networks to obstruction, and security of the data in the networks, which have been in progress generally as planned. Those for the category (4) include the techniques for rule processing for development of protocols, protocols for mutually connecting the systems, and high-speed, high-function networks, which have been in progress generally as planned. It is expected that the original objectives are finally achieved, because the development programs for these categories have been in progress generally as planned. (NEDO)

FY1995 report on the analyses of functional living systems using magnetic stimulation and magnetic fields; 1995 nendo jiki shigeki oyobi kyojiba ni yoru seitai kino kaimei

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-05-01

The purpose of the project is to widen the understanding of the biological effects o magnetic fields and to search potential applications of biomagnetics to medical diagnosis and treatments. We developed a method of localized magnetic stimulation of the brain. By concentrating induced eddy currents on a target with a pair of opposing pulsed magnetic fields produced by a figure-eight coil, they were able to stimulate the human cortex within a 5 mm resolution. We studied the properties of diamagnetic water in static magnetic fields. The phenomenon that the surface of the water was pushed back by magnetic fields of higher gradients was observed. The behavior of oxygen dissolved in an aqueous solution under magnetic fields of up to 8T with a gradient of 50T/m was studied. For oxygen concentrations greater than 11 mg/l, a clear redistribution of dissolved oxygen was observed. Effects of strong magnetic fields on a process of dissolution of fibrin clots was studied. Fibrin polymers in water magneto-phoresically drifted in the direction of increasing magnetic fields, and dissolution of fibrin polymers by plasmin was accelerated. (NEDO)

Effect of mixture formation process of premixed lean diesel combustion. Study of the effect of mixture homogeneity on premixed lean diesel combustion in aid of numerical simulation; Yokongo diesel nensho ni okeru kongoki keisei katei no eikyo. Kongoki no kin`itsusei no eikyo to suchi simulation ni yoru kosatsu

Energy Technology Data Exchange (ETDEWEB)

Shimazaki, N; Miyamoto, T; Akagawa, H; Tsujimura, K

1997-10-01

NOx emission was extremely decreased by PREDIC (PREmixed lean DIesel Combustion) in which fuel was injected at very early stage of compression stroke and the combustion started at near the TDC by self ignition. We have considered that NOx reduction is caused the decrease of a region of stoichiometric mixture ratio by means of extremely early injection. Therefore the homogeneity is very important to decrease of NOx. In this study to investigate the effect of mixture homogeneity in the PREDIC, gaseous fuels (DME, CH4) were charged into the intake, by the combination of direct fuel injection, the mixture heterogeneity was positively changed. In addition the mixture formation process is shown in aid of numerical simulation, it is observed that the homogeneous has the advantage of low NOx emission in PREDIC region. 9 refs., 10 figs., 1 tab.

FY 2000 report on the results of the research and development project for utilization of information of high-molecular-weight structures in a living body. Survey on the technological trends of utilizing the reactions with metals in a living body; 2000 nendo seitai kobunshi kozo joho riyo gijutsu kaihatsu chosa hokokusho. 'Seitai kinzoku hanno riyo gijutsu' ni kansuru gijutsu doko chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the FY 2000 results of the survey on the technological trends of utilizing the reactions with metals in a living body, noting the bio-processes effectively coping with the environmental problems. The effects of heavy metals on microorganisms have been investigated on the molecular biology level, but are not fully elucidated. Recently, the microorganisms capable of converting inorganic metal ions in water into the insoluble compounds have been known, leading to possibility of bioremediation to solve pollution by heavy metals, which have detrimental effects on human health. Heavy metals must be recovered, because they are not extinct by decomposition. The plant aided purification has been attracting attention to cope with heavy metals accumulated in soil. Application of bacteria-aided leaching, which is adopted as one ore smelting process, to the technologies for utilizing metals in a living body has been expected, because diversified activities of inanimate matters in extreme environments have been known. Recently, bio-machining of metals aided by Thiobacillus ferrooxidans, one species of independent nutrient bacteria capable of eating metals, has been developed to a potentially viable stage. (NEDO)

FY 2000 report on the results of the research and development project for utilization of information of high-molecular-weight structures in a living body. Survey on the technological trends of utilizing the reactions with metals in a living body; 2000 nendo seitai kobunshi kozo joho riyo gijutsu kaihatsu chosa hokokusho. 'Seitai kinzoku hanno riyo gijutsu' ni kansuru gijutsu doko chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the FY 2000 results of the survey on the technological trends of utilizing the reactions with metals in a living body, noting the bio-processes effectively coping with the environmental problems. The effects of heavy metals on microorganisms have been investigated on the molecular biology level, but are not fully elucidated. Recently, the microorganisms capable of converting inorganic metal ions in water into the insoluble compounds have been known, leading to possibility of bioremediation to solve pollution by heavy metals, which have detrimental effects on human health. Heavy metals must be recovered, because they are not extinct by decomposition. The plant aided purification has been attracting attention to cope with heavy metals accumulated in soil. Application of bacteria-aided leaching, which is adopted as one ore smelting process, to the technologies for utilizing metals in a living body has been expected, because diversified activities of inanimate matters in extreme environments have been known. Recently, bio-machining of metals aided by Thiobacillus ferrooxidans, one species of independent nutrient bacteria capable of eating metals, has been developed to a potentially viable stage. (NEDO)

Fiscal 1999 survey report on introducing technique for predicting impact on hot spring; 1999 nendo onsen eikyo yosoku shuho donyu chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-10-01

For the application of fruits of the geothermal development promotion project to survey phase C and for the study of technical means for appropriate development to employ after phase C, some cases of impacts imposed on hot springs by geothermal development were taken up and the causes of the impacts were investigated. Activities were conducted in the three fields of (1) the survey of actualities of impacts imposed on hot springs, (2) the survey of the causes of such impacts, and (3) a comprehensive survey. Keyword searches were conducted into the data system and geothermal energy related magazines, and 13 cases were found in which hot springs were affected by geothermal development, which included the Palinpinon district (Philippines), the Koso district (America), and the Wairakei district (New Zealand). Concerning the 13 cases, data on geology, geological structures, and geothermal fluids were collected and studies were conducted about relations of geothermal development with geological structures and geothermal fluids, as in the case of hot springs, and the two were integrated for the clarification of the causes of impacts. In concluding the report, the difference in mechanism is deliberated between cases with impacts on hot springs and cases without impacts on hot springs. (NEDO)

International symposium on environmental impacts of advanced alternative to CFC; CFC shinki daitai busshitsu no kankyo eikyo ni kansuru kokusai symposium hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-07

The international symposium on environmental effects of new CFC substitutes was held in Tsukuba City, Ibaraki Pref. on February 7-9, 1996, and 19 papers were made public. In Session 1 (Plenary lecture), reports were made on Global warming and climate change: a review of recent studies; Stratospheric ozone, CFCs, and CFC-substitutes: an update, etc. In Session 2, Measurements of OH rate constants for advanced refrigerants as well as HCFCs and HFCs; The reaction rate of CFC alternatives with OH radical; Experimental and estimated rate constants: reactions of hydroxyl radicals with several halocarbons, etc. In Session 3, Measurement of uptake coefficients of some acetyl halides and fluorinated ethers into water; Mass transfer at the air/water interface: removal processes of halocarbonyl compounds; Heterogeneous reactions of fluorinated ethers on allophane or titanium dioxide, etc. In Session 4, papers were reported on model calculations relating to the global warming.

Influence of molybdenum on hardenability of destabilized high chromium cast irons. Ko kuromu chutetsu no netsushori tokusei ni oyobosu moribuden no eikyo

Energy Technology Data Exchange (ETDEWEB)

Kuwano, M. (Ube, Collete of Technology, Yamaguchi (Japan)); Ogi, K. (Kyushu University, Fukuoka (Japan). Faculty of Engineering); Sawamoto, A. (Yamaguchi University, Yamaguchi (Japan))

1991-07-25

Alloy elements are added to compensate for reduction in hardenability of high chromium cast iron as a result of destabilization heat treatment. With the purpose of investigating the influence of the added elements, this paper describes investigations made on effects of Mo and destabilization heat treatment conditions on martensite transformation , eutectoid transformation and base hardness, using Fe-Cr-C-based alloy containing C at 1.6-3.6%, and Cr at 6.6-26%. The main results obtained are as follows: Mo and Cr had the distribution coefficient for initial crystal austenite is smaller than one and were microscopically segregated in the dendrite base; the solute element distribution in the base is homogenized as a result of the long-time destabilization heat treatment while the Cr and C concentrations reduce largely, and the Mo concentration increases slightly; Mo has little influence on the Ms point, and reduces with the smaller the Cr/C ratio and the higher the retention temperature; and the base hardness corresponds well to a CCT diagram. 14 refs., 11 figs., 1 tab.

Effects of fuel properties and oxidation catalyst on diesel exhaust emissions; Keiyu seijo oyobi sanka shokubai no diesel haishutsu gas eno eikyo

Energy Technology Data Exchange (ETDEWEB)

Aihara, S; Morihisa, H; Tamanouchi, M; Araki, H; Yamada, S [Petroleum Energy Center, Advanced Technology and Research Institute, Tokyo (Japan)

1997-10-01

Effects of fuel properties (T90 and Poly-Aromatic Hydrocarbons: PAH) and oxidation catalyst on diesel exhaust emissions were studied using three DI diesel engines and two diesel passenger cars. (IDI engine) PM emissions were found to increase as T90 and PAH increased and could be decreased considerably for each fuel if an oxidation catalyst was installed. 5 refs., 9 figs., 3 tabs.

Influence of flow force on the flapper of a water hydraulic servovalve; Suiatsu servo ben no flapper ni sayosuru ryutairyoku no eikyo

Energy Technology Data Exchange (ETDEWEB)

Urata, E. [Kanagawa University, Kanagawa (Japan). Faculty of Engineering; Yamashina, C. [Ebara Research Co. Ltd., Kanagawa (Japan)

1997-06-25

In this paper flow force due to nozzle flow and its influence on the flapper-nozzle system for water hydraulic servovalves are discussed. The flow force acting on the flapper is estimated using the momentum theory, and expressed as a function of the nozzle pressure and flapper-nozzle gap. Analysis shows that the double nozzle flapper gives a quasilinear characteristic to the relationship between the force on the flapper, the flapper gap and the spool velocity. The numerical result based on the theory is used to estimate accuracy of the classical linear approximation. The flow force reduces the magnitude of the change of the nozzle back pressures which drive the spool of the water hydraulic valve, because the input moment acting on the armature is resisted by the moment due to the flow force. Experimental verification of the theory is also given. 7 refs., 10 figs., 1 tab.

Effects of ferrous ions on the metabolism of sulfate-reducing bacteria; Ryusan`en kangenkin no taisha ni oyobosu tetsu ion no eikyo

Energy Technology Data Exchange (ETDEWEB)

Baba, F.; Suzuki, T. [Ajinomoto Co. Inc., Tokyo (Japan). Technology and Engineering Lab.]: Seo, M. [Hokkaido Univ., Sapporo (Japan). Graduate School

1995-11-15

The grave damages due to microorganisms occur occasionally to the ironic piping and the like when river water is used as industrial water. In the present researches, the effects of Fe{sup 2+} on the amount and activity of sulfate-reducing bacteria in the culture medium with the concentration of Fe{sup 2+} changed by stages from 3.6{times}10{sup -4} M to 0.7M are examined. Further, the relations between the activity of the bacteria and the amount of FeS generated in the medium are investigated as an in-site means to observe the activity of the bacteria in the medium wherein the produced S{sup 2-} is converted into FeS once it is generated. The following conclusions are drawn therefrom. In the initial medium with the Fe{sup 2+} concentration from 3.6{times}10{sup -4} M to 0.7M, the growth of the bacteria is maximum at the concentration of 1.0{times}10{sup -2}. Over this concentration the growth is weakened due to the osmotic pressure, lowering of nutriment and the deposit of waste, and the bacteria are extirpated due to the direct effect of osmotic press when the concentration is 0.7M. The total amount of FeS produced due to the bacteria is in conformity with the tendency of growth of bacteria till 30 hours of culture. 18 refs., 6 figs., 2 tabs.

Emission characteristics of multiple stage diesel combustion. Effect of exhaust gas recirculation; Nidan nensho diesel kikan no haishutsubutsu tokusei. EGR no eikyo

Energy Technology Data Exchange (ETDEWEB)

Hashizume, T.; Miyamoto, T.; Akagawa, H.; Tsujimura, K. [New A.C.E. Institute Co. Ltd., Tokyo (Japan)

1998-05-01

For an aim to reduce NOx emission from diesel engines, it has become possible to realize it with smoke emission maintained at low levels by taking the following steps: initial combustion is carried out as lean pre-mixed combustion by adopting early fuel injection; the fuel is injected again after completion of this combustion; and EGR is combined with two-stage combustion which performs diffusion combustion under high temperature atmosphere. When a large quantity of EGR is used, cylinder temperature drops to have ignition timing delayed in the first stage, serving for improving fuel consumption. The problem of increase in smoke generation is solved by optimizing the injection timing at the second stage to suppress smoke generation increase, resulting in realization of lower NOx emission. By completing the second-stage fuel injection before ignition of the first-stage injection, it was possible to realize further lower NOx emission. Smoke increase due to higher EGR ratio was suppressed by pre-mixing both fuels injected in the first and second stages, although this is a high load operation. In addition, oxygen concentration and cylinder temperature were reduced, the gas pre-mixture was homogenized, and combustion velocity was suppressed by delaying the angle of ignition timing. This made low smoke combustion at {lambda} = 1 possible even in compressed ignition combustion. 8 refs., 12 figs., 1 tab.

Global environment assessment survey by advancing the energy demand and supply structure. 4; Energy jukyu kozo kodoka chikyu kankyo eikyo chosa. 4

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

To investigate the energy demand and supply structure in Japan, the international trend of approaches to global warming problems and the mitigation options to global warming in the energy related sectors have been surveyed. For the United Nations Framework Convention on Climate Change, an Ad-hoc Group has discussed relevant topics after the 1st conference of the Parties. Meetings of the Group primarily focused on what objectives to set for the reduction of greenhouse gas (GHG) emissions in and in and after 2000. IPCC completed their Technical Paper in November 1996 in which technologies and measures to reduce GHG emissions and to enhance GHG sinks were analyzed and evaluated in various aspects. This Paper discusses about each sector of institutional buildings sector, transport sector, industrial sector, and energy supply sector. Especially, in the energy supply sector, promising approaches to reduce future emission include more efficient conversion of fossil fuels, switching to low-carbon fossil fuels, decarbonization of flue gas and fuels, CO2 storage, switching to nuclear energy, and switching to renewable sources of energy. 5 refs., 2 figs., 14 tabs.

Study of effects of engine oil additives on the properties of fluorelastomers; Fusso gomu ni oyobosu engine yu tenkazai no eikyo chosa

Energy Technology Data Exchange (ETDEWEB)

Kurono, K; Owaki, M; Suzuki, Y; Akiyama, K; Shionoya, M [Toyota Motor Corp., Aichi (Japan)

1997-10-01

Fluoroelastmers are well known for their resistance to heat and fluids and have become major material for crankcase oil sealers. On the other hand new additive formulations are developed for engine lubricants used for fuel economic gasoline engines. In this paper the effects of those additives on properties of fluoroelastmers are investigated. The results of the immersion tests of both test plaques and oil sealer products indicates that dithiocarbamates friction modifier have hardening effects on fluoroelastomers. The fluoroelastmer deterioration mechanism is presumed by analysis of elastmer samples after immersion in oil. 6 refs., 9 figs., 3 tabs.

Interim evaluation report of the mutually operable database systems by different computers; Denshi keisanki sogo un'yo database system chukan hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1989-03-01

This is the interim report on evaluation of the mutually operable database systems by different computers. The techniques for these systems fall into four categories of those related to (1) dispersed data systems, (2) multimedia, (3) high reliability, and (4) elementary techniques for mutually operable network systems. The techniques for the category (1) include those for vertically dispersed databases, database systems for multiple addresses in a wide area, and open type combined database systems, which have been in progress generally as planned. Those for the category (2) include the techniques for color document inputting and information retrieval, meaning compiling, understanding highly overlapping data, and controlling data centered by drawings, which have been in progress generally as planned. Those for the category (3) include the techniques for improving resistance of the networks to obstruction, and security of the data in the networks, which have been in progress generally as planned. Those for the category (4) include the techniques for rule processing for development of protocols, protocols for mutually connecting the systems, and high-speed, high-function networks, which have been in progress generally as planned. It is expected that the original objectives are finally achieved, because the development programs for these categories have been in progress generally as planned. (NEDO)

Development of an observation robot `Flying Fish` for comprehensive measurements of ocean environment; Kaiyo kankyo sogo kansoku robot `flying fish` no kaihatsu kenkyu

Energy Technology Data Exchange (ETDEWEB)

Koterayama, W.; Yamaguchi, S.; Nakamura, M. [Kyushu Univ., Fukuoka (Japan). Research Inst. for Applied Mechanics; Akamatsu, T. [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan)

1996-06-01

A high speed towed type physical and chemical observation marine robot named as `Flying Fish` has been developed since 1992, which can measure chemical substances in the sea as well as physical data, such as flow velocity of the ocean and water temperature. This paper describes its formation, designing, control system, and results of ocean tests. For the space continuous observation of physical, chemical, and biological quantities, it is essential to control the depth, pitch, and roll. The wing control method was employed for this robot. As a result of the ocean tests, the following conclusions were obtained. The accuracy under the steady state was {plus_minus}0.05 m in the depth, {plus_minus}1 degree in the pitch, and {plus_minus}0.5 degree in the roll. This was stable enough to operate chemical analysis, such as dissolved oxygen analysis. Even under the unsteady state during the change of depth, the pitch and roll were controlled in {plus_minus}3 degree and {plus_minus}0.5 degree, respectively. Results of the field tests and the numerical simulations for the performance of this robot were agreed well mutually in the practically sufficient accuracy. 10 refs., 15 figs., 2 tabs.

Development of an observation robot `Flying Fish` for comprehensive measurements of ocean environment; Kaiyo kankyo sogo kansoku robot `flying fish` no kaihatsu kenkyu

Energy Technology Data Exchange (ETDEWEB)

Koterayama, W.; Yamaguchi, S.; Nakamura, M. [Kyushu Univ., Fukuoka (Japan). Research Inst. for Applied Mechanics; Akamatsu, T. [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan)

1996-12-31

With an objective for spatial continuous measurement of physical, chemical and biological amounts in ocean, development has been made on a wing controlled towed vehicle, `Flying Fish` which is capable of controlling depth, pitch and roll. Numerical simulations and two-year sea experiments have been carried out for the development. Flying Fish consists of a sub-system comprising a towing vehicle, towing cables, and on-board controllers. In a steady state, Flying Fish can be controlled at accuracy for depth of {plus_minus} 0.05m, pitch of {plus_minus} one degree, and roll of {plus_minus} 0.5 degree. This accuracy is sufficient for operating a chemical analyzer, the dissolved carbonic acid analyzer. Even in a non-steady state such as in changing the depth, the pitch can be controlled at {plus_minus} 3 degrees and the roll at {plus_minus} 0.5 degree. This extent of attitude change is within a range rendering no problems in maintaining accuracy of the measurement devices. The result of sea experiments for movements of Flying Fish agreed with that of the numerical simulation at practically usable accuracy. Flying Fish is verified as an effective system in investigating spatial variations in ocean data. 10 refs., 15 figs., 1 tab.

FY1995 microalgal biotechnology for recycling of pollutants; 1995 nendo tayona sorui kino wo kiban to suru seibutsuken busshitsu junkangta sogo saishigenka gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The objectives are 1) development of biological processes needed for the treatment of pollutants and the conversion of resulting biomass to value added products such as energy and fine chemicals, and 2) development of techniques for monitoring of both biological and chemical hazards associated with process operation. We developed a microalgal system for simultaneous removal of CO{sub 2}/NO{sub x} from flue gas, as well as an electro-osmotic method for recovery of microalgal cells. A strategy for effective culturing of photoautotrophic cells in photobioreactors was also proposed. We utilized waste algal biomass to produce biosurfactants, and studied about structure-function relationship of lipopeptide biosurfactants. As an energy product, H{sub 2} was produced via lactic acid fermentation of algal biomass. Physiology of marine phytoplankton was also studied in relation to the future mass production of microalgal biomass. A rapid monitoring of microbial populations was possible by using fluorescent probes. An enzyme immunosorbent assay system specific to fish metallothionein was established for the assessment of aquatic environmental pollution. Human herpesvirus latent infection was effectively applied to biological assay of environmental hygiene. (NEDO)

Effect of oil around the pin boss bearing on bearing friction force; Piston pin jikuukebu kinbo no junkatsuyu ga masatsuryoku ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Takiguchi, M; Suhara, T; Ato, S; Someya, T [Musashi Institute of Technology, Tokyo (Japan)

1997-10-01

Piston pin bearings are engine parts placed under severe lubricating condition because of the high unit load and temperature and the low sliding speeds. Therefore, they are vulnerable to many lubrication problems such as abnormal wear, scuffs and seizures. In our recent study, the bearing friction were measured using a original measuring device and it was found out that the lubricating conditions of piston pin boss bearings are non-fluid lubrication due to the oil starvation. In this study, we have also measured the lubricating oil behavior around the pin boss bearing using a special cylinder with glass window, and analyzed the relationship between the friction force and the oil behavior at the pin boss bearings in a actual operating gasoline engine. 2 refs., 9 figs., 1 tab.

Temperature effect on corrosion fatigue strength of coated ship structural steel; Zosen`yoko tosozai no fushoku hiro kyodo ni okeru ondo no eikyo

Energy Technology Data Exchange (ETDEWEB)

Takanashi, M.; Fuji, A.; Kojima, M.; Kitagawa, M. [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan); Kobayashi, Y. [Ship Research Inst., Tokyo (Japan); Kumakura, Y.

1997-08-01

The corrosion fatigue life was obtained using uncoated and tar epoxy resin specimens to clarify the temperature effect. The life curve for corrosion fatigue of machined and uncoated steel in the air and sea was obtained. The fatigue strength of uncoated steel largely decreases in the sea and breaks even in the nominal stress range of less than 1/2 of the fatigue limit in the air. The effect of temperature on the coated steel is represented by a corrosion coefficient. The steel coated at 25{degree}C is 1/1.03 to 1/1.13 at 40 to 60{degree}C. This showed that the fatigue strength decreases when the temperature exceeds 25{degree}C. However, it has not such tendency and significance that are represented quantitatively. There is a slight difference in the short-life area between the crack generation life and breaking life. However, the long-life area has no significance that influences the whole evaluation. In the long-life corrosion fatigue, the crack occurs from the corrosion pit due to the exposure below the coated film and progresses in the base material before the coated film is destroyed. The effect of the corrosion pit remarkably appears at a low-stress level. 14 refs., 14 figs., 4 tabs.

Effect of Water Environment on Subcritical Crack Growth of Machinable Ceramics; Kaisakusei seramikkusu no kiretsu shinten tokusei ni oyobosu mizu kankyo no eikyo

Energy Technology Data Exchange (ETDEWEB)

Ikeda, K.; Kaizu, K.; Inotani, T. [Miyazaki Univ., Miyazaki (Japan); Yoshikawa, A.; Adachi, K.; Igaki, H. [Osaka Sangyo Univ., Osaka (Japan)

1997-06-15

The fatigue behavior of ceramics has been discussed on the basis of the relation between stress intensity facter (KI) and crack velocity (V). In this paper, the effect of environment on the relation between KI and V was studied on machinable ceramics (mica glass ceramics) and two kinds of glass ceramics with different grain sizes. The double torsion (DT) technique was used for the determination of the KI-V characteristics under different environments of air and ion-exchanged water. The characteristics of acoustic emission (AE) during stress corrosion cracking of mica glass ceramics was also examined. In water environment, the region II in the KI-V curve, in which crack velocity varies slowly with KI, disappeared. From this experimental fact, it was considered that at high KI, the crack velocity is encouraged by diffusion of the corrosive species to the crack and thus depended on the amount of water. SEM farc tography revealed that mica single crystals in the material caused crack arrest and deflection to occur. It is also found that AE event rate is quantitatively related to the crack velocity. AE measurement can be used in studying the crack propagation behavior of mica glass ceramics. 11 refs., 12 figs., 3 tabs.

Fiscal 1998 research report on the global environmental assessment for efficient energy consumption; 1998 nendo energy shohi koritsuka chikyu kankyo eikyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

International Panel on Climate Change (IPCC) published the 1st assessment report in 1990 and the 2nd report in 1995 since its establishment in 1988, and is promoting the 3rd research and analysis. Among them, this report describes the study on technology transfer for efficient energy consumption. For stabilizing greenhouse effect gas concentrations in the air, strong control of such gas emission is indispensable, and a role of technology is important for the control. For overcoming some weak points for climate change, practical use of applicable technologies is necessary over a certain period of time, and technology transfer is essential in each country and all over the world. For promotion of such approach, the analysis and evaluation for technology transfer and diffusion are useful in addition to reports on technology itself. Based on such understanding, IPCC has promoted preparation of the special report on methodological and technological issues of technology transfer since 1997. Its approval at the IPCC general meeting is expected in late 1999 or early 2000. Some chapters related to efficient energy consumption are presented. (NEDO)

Effects of electrical stimulation on fruit of lentinus edodes; Shiitake jinko kindoko ni taisuru denki shigeki ga kojittai hassei kosu ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Mitobe, K.; Sato, T.; Yoshimura, N. [Akita Univ. (Japan)] Suzuki, T. [Tohoku Electric Power Co. Ltd., Sendai (Japan)

1997-11-30

So far, the cultivation of Lentinus edodes is cultivated from material wood mainly, however, recently, artificial bed-blocks method has been used widely. The advantage of bed-block cultivation is to a short growing period and be possible to cultivate by a large scale facilities. Hereafter, it is thought that this growing method is used mainly. Before now, based on the experimental fact that abnormal fruiting of Lentinus edodes occurs due to lightening, the study on the effects of electrical stimulation was reported, however, the investigation on the effects of electrical stimulation on the artificial bed-bocks which is thought to come into wide use in future does not carry out until now. The purpose of this study is to investigate an increased yield of the Lentinus fruit-bodies grown on artificial bed-blocks that electrical stimuli were applied. Nineteen artificial bed-blocks were provided for each applied voltage condition; Control, 200V, 400V, 600V, for the AC. As a result of experiment, in the 600V condition, the total number of fruiting of Lentinus edodes was significantly increased as compared with other conditions. Especially, in the artificial bed-blocks that peak current was over 300 mA, the total number of fruiting was increased. 6 refs., 6figs.

Report on the survey made under the research contract with NEDO, `The International Work Division/Energy Demand Effect Survey.`. Influence of the economic growth in Asia on the energy demand; 1996 nendo `kokusai suihei bungyo energy juyo eikyo chosa` itaku chosa kekka hokokusho. Asia no keizai hatten ga energy juyo ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This report includes surveys on the following: (1) the progress situation of the Asian information society, (2) changes of corporate network, business flow, material flow and money flow in association with the information society, (3) the present situation of the industry-accumulated region in Asia and inter-region network, (4) impacts of the above-mentioned changes on the trade and investment structure in Japan, (5) how to tackle the energy issue in Asia in the future. First, effects of the advance of the information society on energy supply/demand were studied. Next, an analysis was made of effects of the progress of the high-grade information society in Asia on economy, industry and corporate action. The degree of the progress of the information society in Asian countries was made clear from the infrastructure arrangement and the developmental status of application. Contribution of the financial network to the economic growth in Asia and the development were clarified. The organization of corporate networks in Asia where paradigms are converting was made clear to consider industrial clusters in Asia. Last, in the light of the economic relationship between Japan and Asia, a study was made on the future policy of Japan for Asia. 238 refs., 77 figs., 89 tabs.

Fiscal 1999 survey report. Survey of effect of energy efficiency improvement on global environment; 1999 nendo energy shohi koritsuka chikyu kankyo eikyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Analyses are conducted into consideration given to global warming measures in the 3rd assessment report of the Intergovernmental Panel on Climate Change (IPCC) and into technology transfer from developed nations to developing nations in the Asia-Pacific region etc. to contribute to their energy efficiency improvement. The aim is to present data for deliberation as to how future energy efficiency improvement measures should be in the Asia-Pacific region. The chapters (Chapter 0 through Chapter 10) of the report to be worked out by Working Group III deeply involved in energy problems are 0) Introduction, 1) Scope of the report; 2) Socio-economic and emissions scenarios; 3) Technical and economic potential of GHG (greenhouse gas) emissions reduction; 4) Technical and economic potential of biological CO2 mitigation options; 5) Barriers, opportunities and market potential of technologies and practices; 6) Policies, measures and instruments; 7) Costing methodologies; 8) Global, regional and national costs and ancillary benefits of mitigation; 9) Sector costs and ancillary benefits of mitigation; and 10) Decision making frameworks. As the result of the survey, some actual technology transfer implementations are introduced covering branches closely related to energy efficiency improvement, which are branches of construction, traffic, industry, energy supply, and wastes. (NEDO)

Effects of lithium iodide doping on devolatilization characteristics of brown coals; Yoka lithium no tenka ga kattan no kanetsu henka katei ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Muraoka, J.; Kumagai, H.; Hayashi, J.; Chiba, T. [Hokkaido University, Sapporo (Japan)

1996-10-28

In order to discuss effects of lithium iodide (LiI) doping on condensation structure of brown coals during heating, spectral changes were measured by using an in-situ FT-IR. It was found that the LiI doping accelerates weight reduction due to heating, and the doping effect is affected by coal structure. Both of Loy Yang (LY) coal and its LiI doped coal (DLY) had absorption intensity of the FT-IR spectra decreased with rising temperature, and the absorption center belonging to an OH group shows different shifts between the LY and DLY coals. This indicates that the LiI doping has affected the change in hydrogen bonding patterns associated with heating. Both of South Banko (SB) and LY coals had the absorption spectral intensity in the OH group decreased as the weight reduction (conversion) rate increased. Reduction in the OH groups associated with heating is caused by volatilization and condensation reaction in light-gravity fraction. However, in the case of equal conversion rate, the LiI doped coal shows higher spectral intensity than the original coal, with the LiI doping suppressing reduction in the OH groups. It appears that the doping suppresses the condensation reaction between the OH groups. 2 refs., 6 figs., 1 tab.

Influence of frequency spectra to annoyance caused by road traffic noise; Doro kotsu soon no urusasa ni oyobosu shuhasu supekutoru no eikyo ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Ishiyama, T [Japan Automobile Research Institute Inc., Tsukuba (Japan); Hashimoto, T [Seikei University, Tokyo (Japan)

1997-10-01

This paper describes a study of annoyance to road traffic noise in laboratories. To measure the annoyance to road traffic noise, subjective evaluation test was carried out using 48 road traffic noise recorded at various points in the city. Among the frequency spectra of these noise, the differences on the SPL of high frequency component were significant. As a result, we found that: (1) annoyance was different while A-weighted SPLs were the same, (2) fluctuation strength had the highest correlation with annoyance, (3) besides A-weighted SPL, roughness and sharpness contributed to annoyance -simultaneously, (4) contribution of high frequency noise was significant to annoyance. 2 refs., 11 figs., 1 tab.

Effect of low oxygen partial pressure to the bumblebee respiration; Naruhanabachi ni okeru taikichu sanso bun'atsu henka no kokyu ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Komai, Y. [Japan Science and Technology Corp., Tokyo (Japan)

1999-06-25

Insects augment oxygen supply using convective transport during flight in two ways: with deforming tracheae by surrounding muscles movement (muscle pumping) and with contracting air sacs by exoskeleton movement (abdominal or thoracic pumping). However, because induced flow inside tracheae is difficult to measure, it is not known how the convective transport actually contributes. By comparison between direct measurement of oxygen partial pressure in a flight muscle based on electrochemical method and flight/ventilation activities in a bumblebee, Bumbus hypocrita hypocruta, a method was developed for estimating gas transport efficiency. Oxygen partial pressure, P{sub 02}, in the bee periodically fluctuated with discontinuous abdominal movement in normal air. While the P{sub 02} strongly varied among individuals in normal air, the P{sub 02} took a unique value in oxygen poor air ({<=}8%). By enhancing ventilation, the bee could respire in an oxygen poor atmosphere up to 2%. Furthermore, the bee could fly in an atmosphere of 6%, in which the P{sub 02} decreased to 0.7%. Estimated efficiency of the gas transport increases with atmospheric oxygen concentration decreases. (author)

Study on the performance improvement of multiblade fans. Effects of suction cones; Tayoku fan no seino kaizen ni kansuru kenkyu. Suction cone no eikyo

Energy Technology Data Exchange (ETDEWEB)

Kuratani, F.; Ogawa, T. [Hyogo University of Teacher Education, Hyogo (Japan); Yamamoto, S.

1999-07-25

In order to improve the performance of a multiblade fan, the effects of three types of suction cones of the fan casing on the fan efficiency and noise are investigated experimentally. The first type of the suction cone is the insertion type, which is inserted into the inside of the fan impeller. The second type is the extrusion type, which extrudes outside from the casing surface. The third type is the combination type of two types. The results of those three types are compared with those of the commonly used suction cone. The followings are made clear: (1) The insertion type and the extrusion type are effective in improving the efficiency and reducing noise. (2) The optimal lengths of the insertion and the extrusion exist. (3) The combination type is more effective in improving the efficiency. (4) The combination type with the skewed cutoff of the fan casing shows the best effect. (author)

Study on the effect of measurement points upon reduced added mass matrix; Shukusho fuka shitsuryo matrix ni okeru kansokuten no eikyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Funaki, T.; Hayashi, S. [Osaka University, Osaka (Japan). Faculty of engineering

1996-12-31

It is known in estimating vibration characteristics of a ship that fluid range affects largely a structure. A parameter calculation was performed on node vibration in the vertical direction of a rotating elliptic body such as a ship to investigate the effect of an arranging method of the measurement points upon the result of the analysis. As a result, it is thought that equivalent interval arrangement of 21 measurement points would be sufficient in a lower order side mode of vibrations with less than four nodes. An analysis of calculations performed by arranging measurement points in experimental measurement points revealed that analysis accuracy would not increase even if the number of measurement points is increased if it is done so without considering rotation vector. An experiment was carried out with the number of measurement points increased to verify the above fact, with which the analysis was verified correct. Therefore, as has been forecasted in the previous report, the cause for the analysis accuracy deterioration in a high order mode may be estimated as the effect of the rotation vector. However, since it is not the situation that an analysis considering the rotation vector has been conducted, it cannot be concluded yet that the effect of the rotation vector is the sole cause. 4 refs., 14 figs., 7 tabs.

Economic development in India and the effect on the energy market in Asia; Indo no keizai hatten to Asia no energy shijo eno eikyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-07-01

As for the real GDP growth rate in India, the real GDP per capita during 1980-1993 increased 2.9% on annual average, but that in China did 8.0%. India has largely been behind China in the economic growth, but since the liberalization of economy in 1991, the Indian economy has remarkably been developed. It is predicted that the real GDP during 1993-2010 will be 5-6% on annual average. The difference in GDP increase between India and China is caused by differences in energy conservation, speed of conversion from non-commercial energy to commercial energy, serviceability of the industrial structure, etc. It is predicted that the primary energy consumption will grow on the level of China. The oil demand will grow 4-6% in China and 5-6% in India in 1993-2010, showing more increase in India. For oil import to India to exceed 1 million B/D in 2000, it is necessary to clear the ceiling of the international balance. For India to become a big country corresponding to its population size, a lot of difficulties should be overcome. 49 refs., 104 figs., 62 tabs.

Study on the effect of measurement points upon reduced added mass matrix; Shukusho fuka shitsuryo matrix ni okeru kansokuten no eikyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Funaki, T; Hayashi, S [Osaka University, Osaka (Japan). Faculty of engineering

1997-12-31

It is known in estimating vibration characteristics of a ship that fluid range affects largely a structure. A parameter calculation was performed on node vibration in the vertical direction of a rotating elliptic body such as a ship to investigate the effect of an arranging method of the measurement points upon the result of the analysis. As a result, it is thought that equivalent interval arrangement of 21 measurement points would be sufficient in a lower order side mode of vibrations with less than four nodes. An analysis of calculations performed by arranging measurement points in experimental measurement points revealed that analysis accuracy would not increase even if the number of measurement points is increased if it is done so without considering rotation vector. An experiment was carried out with the number of measurement points increased to verify the above fact, with which the analysis was verified correct. Therefore, as has been forecasted in the previous report, the cause for the analysis accuracy deterioration in a high order mode may be estimated as the effect of the rotation vector. However, since it is not the situation that an analysis considering the rotation vector has been conducted, it cannot be concluded yet that the effect of the rotation vector is the sole cause. 4 refs., 14 figs., 7 tabs.

FY1995 study of the new generation system for the vector type biomagnetmeter and optimization of the system; 1995 nendo jisedai seitai jiki tajigen keisoku system oyobi saitekika no kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The most advanced devices for magneto-encephalography(MEG),so far developed are equipped with more than 100 channels which measure the z-component of the magnetic field perpendicular to the surface of the scalp or of the chest, However, there do not exist any multi-channel MEG measuring device capable of measuring the three components of the MEG vectors. The purpose of this study is to develop a SQUID magnetometer with more than 180 channels with the configuration for the three-component vector measurement and to apply the device to the investigation of the higher functions of the brain of which the mechanisms are still largely unknown. Furthermore, it will open up new clinical methods for various discases. 1) We arranged three coils in a column to measure the x,y and z-components of the magnetic field and arranged 60 of those columns so that they cover the whole scalp and measure the 3-component MEG at 60 points simultaneously. 2) We developed a dewar in which more than 200 SQUID elements can be immersed in liquid helium and at the same time the arrangement of the coils allows as close fit as possible to the scalp to be measured. 3) A gantry was developed for the above dewar so that the dewar might be fixed at an arbitary position and its vibrations were minimized. 4) DOIT-type circuit was adopted for the FLL circuit, which realized a simple system. 5) We established a signal processing system which samples the signal from all the SQUID sensors simultaneously at a high sampling rate and analyzes the data efficiently. 6) We measured 3-component MEG signals and found that it can bring out new information useful for investigating the higher functions of the brain. (NEDO)

Fiscal 2000 comprehensive survey. Project for development of international standards for supporting novel industries; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo. Sogo chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development for creation of international standards had been under way for three years since fiscal 1998 for the sustenance and securement of Japan's technical advantage and for the enhancement of the international competitiveness of its industries. In the ultimate fiscal year for the project, studies were made for establishing standards relative to 13 subjects, involving the management of color reproduction, assurance of interoperability of optical disk systems, digital image processing for home-use digital electronic appliances, securement of connection between information devices for home-use electric appliances, production process system, method for testing and evaluating fine ceramics for communication equipment, method for evaluating high-temperature properties of new glass, method for testing and evaluating corrosion resistance of surface treated steel sheets, method for testing and evaluating pure titanium, method for testing and evaluating plastic optical fiber, method for evaluating properties of high-strength large-diameter steel pipe for ultrahigh-pressure natural gas pipeline, method for measuring fuel consumption of hybrid electric vehicles, method for calculating the recycling rate of automotive products, or the like. The fruits of 77% of the efforts have already been proposed as international standards or have arrived at a stage where they may be proposed as such. (NEDO)

ESR study on the interaction between carbon blacks and oxygen molecules; ESR ho ni yoru carbon black to sanso bunshi tono sogo sayo no kenkyu

Energy Technology Data Exchange (ETDEWEB)

Okazaki, M.; Toriyama, K.; Konishi, Y. [National Industrial Research Institute of Nagoya, Nagoya (Japan)

2000-02-24

Interaction between carbon blacks and oxygen molecules has been studied by means of electron spin resonance (ESR) spectroscopy. The ESR spectra of the carbon blacks appears at the g-value of free spin, which are contributed by both isolated electrons and conduction electrons. Upon introducing oxygen to the system the ESR linewidth was broadened in proportion to the partial pressure of oxygen. In case of lampblack (LB 101, Degussa) the interaction was not so strong that it took a tong time at 77K for the linewidth to reach the maxmum value. In case of gassblack (P 140 V, Degussa), on the other hand, the oxygen was easily adsorbed at 298K and the linewidth at 77K became its maximum immediately after cooling. The number of unpaired electrons decreased when the system was kept at 298 K and the decrease was prominent for the local spins. These phenomena have been explained with a simple band model for the electron. (author)

Fiscal 2000 comprehensive survey. Project for development of international standards for supporting novel industries; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo. Sogo chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development for creation of international standards had been under way for three years since fiscal 1998 for the sustenance and securement of Japan's technical advantage and for the enhancement of the international competitiveness of its industries. In the ultimate fiscal year for the project, studies were made for establishing standards relative to 13 subjects, involving the management of color reproduction, assurance of interoperability of optical disk systems, digital image processing for home-use digital electronic appliances, securement of connection between information devices for home-use electric appliances, production process system, method for testing and evaluating fine ceramics for communication equipment, method for evaluating high-temperature properties of new glass, method for testing and evaluating corrosion resistance of surface treated steel sheets, method for testing and evaluating pure titanium, method for testing and evaluating plastic optical fiber, method for evaluating properties of high-strength large-diameter steel pipe for ultrahigh-pressure natural gas pipeline, method for measuring fuel consumption of hybrid electric vehicles, method for calculating the recycling rate of automotive products, or the like. The fruits of 77% of the efforts have already been proposed as international standards or have arrived at a stage where they may be proposed as such. (NEDO)

Fiscal 1998 research report on the total electric power loss reduction project for Myanmer; 1998 nendo Myanmer koku denryoku soshitsu sogo teigen project chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

As a part of Japanese clean development mechanism, study was made on reduction of greenhouse effect gas emission from thermal power plants by reduction of power transmission and distribution losses of power systems in Myanmer. Study was made on technical power transmission and distribution losses for the national grid transmission system, 33kV sub- transmission system of Thaketa substation in Yangong city, and 6.6kV and 400V distribution systems of Latha and Lanmadaw townships in the downtown area of Yangong. Countermeasures for power loss reduction were considered on the basis of the study result. The loss reduction project plan includes a construction cost of 5,134,000US$, loss reduction of 7,726kW, and loss reduction of 33,213,000kWh. The project feasibility and profitability were evaluated by comparison between a financial internal rate of return (FIRR) and an opportunity cost assuming that a discount rate is the opportunity cost. As a result, FIRR was 17.36% and the discount rate was 8.89% in Myanmer. (NEDO)

FY 1998 report on the results of the R and D for acceleration of biological resource information basement preparation (bioinformatics). Third revision. Development of measurement technology of interaction among biological molecules (Development of high-precise automatic analysis technology for a trace amount of cellular protein); 1998 nendo seibutsu shigen joho kiban seibi kasokuka kenkyu kaihatsu (bioinformatics) seika hokokusho. Seitai bunshikan sogo sayo no keisoku gijutsu no kaihatsu (saibonai chobiryo tanpakushitsu no koseido jido kaiseki gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

An experimental study was conducted with the aim of developing the technology to acquire/analyze in high sensitivity manifestation proteins existing in a trace amount and in various kinds, concretely, signal transfer molecules, transcription factors, etc. which exist in one cell. After extracting a trace amount of functional proteins for analysis from the specified functional cell, the study was made on the following: precise separation and detection technique for cellular proteins, efficient digestion technique and contaminant elimination technique of stained protein, precise separation of peptides by micro-LC technique, precise peptide molecular mass detection of each separated peptide with high sensitivity, reconstruction of protein structure by computer algorithm. As a result, as to the analysis level, an analysis technology with high sensitivity of a 50 fmol level was established as against the existing level of several pmol. Moreover, after the separation/digestion of proteins by the 2D electrophoresis, a series of the process automation system was completed which is high-precise separation using protein columns - molecular analysis - structure prediction by computer. (NEDO)

Effect of fuel composition on poly aromatic hydrocarbons in particulate matter from DI diesel engine; Particulate chu no PAH ni oyobosu nenryo sosei no eikyo

Energy Technology Data Exchange (ETDEWEB)

Tanaka, S; Tatani, T; Yoshida, H; Takizawa, H; Miyoshi, K; Ikebe, H [COSMO Research Institute, Tokyo (Japan)

1997-10-01

The effect of fuel composition on poly aromatic hydrocarbons (PAH) in particulate matter from DI diesel engine was investigated by using deeply desulfurized fuel and model fuel which properties are not interrelated. It was found that the deeply desulfurized fuel have effect on reducing PAH emissions. Furthermore, it was suggested that poly aromatics in the fuel affect PAH emissions and the influence of tri-aromatics in the fuel was promoted by the coexistence of mono-aromatics or naphthene. PAH formation scheme from each fuel component was proposed by chemical thermodynamic data. 4 refs., 8 figs., 3 tabs.

Economical effect of introducing a photovoltaic system on future electric power system; Shorai no denryoku keito eno taiyoko hatsuden system donyu ni yoru keizaiteki eikyo

Energy Technology Data Exchange (ETDEWEB)

Akata, N.; Kenmoku, Y.; Sakakibara, T. [Toyohashi University of Technology, Aichi (Japan); Kawamoto, T. [Shizuoka University, Shizuoka (Japan); Nakagawa, S. [Maizuru National College of Technology, Kyoto (Japan)

1997-11-25

Economic impact of introduction in the future of photovoltaic power generation (PV) systems into the commercial power system is discussed from the electric utilities` point of view. In the discussion, future demand for power is predicted from the demand for power in the base year, and the optimum power source configuration corresponding to the future demand and power generation curve are worked out by use of linear programming. Then, the fixed cost and variable cost are calculated for each of the power source components, and then the expected reduction in cost per unit of power generated is calculated. As the power sources, the hydroelectric, pumped storage, oil-fired, coal-fired, LNG-fired, combined cycle, and atomic technologies are considered. The conclusion is stated below. Upon introduction of PV power equivalent to 10% of the maximum demand power, the maximum power in the service area of Chubu Electric Power Co., Inc., will be reduced by 1.23GW in 2025, and the yearly demand power by 5472GWh. Since PV lowers the peak, an increased number of power sources low in variable cost will be used although such will be low in tracking capability. An increase in power demand will enhance the cost reducing effect of the PV system. 5 refs., 4 figs., 3 tabs.

Influence of hydrogen-ion concentration exponent on undrained shear behaviour of bentonites; Bentonaito no hihaisui sendan kyodo ni oyobosu suiso ion nodo shisu no eikyo

Energy Technology Data Exchange (ETDEWEB)

Kamei, T [Kiso Jiban Consultants Co. Ltd., Tokyo (Japan); Tokida, M [Nagano National College of Technology, Nagano (Japan)

1994-12-21

Because there is a report example that the yield stress of a landslide clay increases along with a decrease of a hydrogen-ion concentration exponent, it is thought that a shear strength of the landslide clay depends on the hydrogen-ion concentration exponent. Furthermore, when the soil stabilization method by lime is applied to the soft ground and high organic earth, it is pointed out that the hydrogen-ion concentration exponent will become one of the harmful factors. Accordingly, it is understood that revealing an influence of a hydrogen-ion concentration exponent affects on the characteristics of an earth is one of the important factors, to evaluate a strength, deformation and so forth of the viscous ground. In this study, in order to examine an influence of a hydrogen-ion concentration exponent affecting on an undrained shear behavior of the bentonites, for the artificially adjusted bentonite specimens with 5 kinds of different pH, the isotropic consolidated undrained triaxial compression tests were performed, and consequently an influence of pH affecting on the engineering characteristics of the bentonites was made clear quantitatively. 28 refs., 16 figs., 5 tabs.

Survey of effects of enhancement of the energy supply/demand structure on the global environment. 3; Energy jukyu kozo kodoka chikyu kankyo eikyo chosa. 3

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

For the purpose of studying how the energy supply/demand structure in Japan should be, a report on the secondary IPCC (Intergovernmental Panel on Climate Change) evaluation was analyzed. Possibilities of reducing the world CO2 emissions in association with the energy consumption were studied in the five assumed cases. Every case says that CO2 can be reduced to 1/3 of the 1990 level by 2100. In a case of the use of biomass as main fuel (1), the use of primary energy is suppressed to two times the 1990 level, and photovoltaic/wind/biomass power generation is introduced in a large quantity. Synthetic methanol and hydrogen are used for transportation and commercial/residential use fuels. There are four more assumed cases: the use of nuclear power as a substitute for renewable energy in the power generation in (1), the use of natural gas of 1.5 times that used in (1), the substitution of coal for biomass used in (1), and the assumption that the demand for primary energy in 2100 will be twice that used in (1). In Japan it is assumed that basically the nuclear power generation will be expanded, that the photovoltaic and waste power generation will be introduced in a large quantity, and that synthetic methanol and hydrogen are mainly used as transportation and commercial/residential use fuels. It is necessary, therefore, to analyze conditions under which the quantity introduction of such non-fossil energy is made possible. 11 figs., 31 tabs.

FY 1993-1999 report on all the results of the development of high performance industrial furnace; Koseino kogyoro no kaihatsu sogo seika hokokusho (1993 - 1999 nendo)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Since an phenomenon was found out that NOx emission, which was thought to be increased, will be decreased by burning the high temperature preheated air jetting it at high speed (high temperature air combustion) in industrial furnace, there appeared a possibility of technical breakthrough for achieving the heightening of energy utilization efficiency and NOx reduction by exhaust heat recovery at the same time. This project aims at conducting full-scale experiments based on the basement technology including the theoretical elucidation of the combustion mechanism and high temperature air combustion by using various experimental facilities. Further, making full use of the most up-to-date analysis methods and constructing general-purpose database, the development is also aimed at of high performance industrial furnaces such as various heating furnace, heat treat furnace and melting furnace, with the assumption of prompt commercialization of the results of the development. As a result, targets were achieved such as energy saving of 30% or more, downsizing of 20% and a remarkable NOx reduction. Core technologies of this project are in-system limit heat recovery technology, high temperature air combustion technology, temperature field control technology (furnace temperature leveling technology) and high exergy heat transfer technology (furnace temperature heightening technology). (NEDO)

Fiscal 1997 report on the results of the international standardization R and D. Overall survey; 1997 nendo seika hokokusho kokusai hyojun soseigata kenkyu kaihatsu. Sogo chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper summed up the results of the survey of tackling with the international standardization by enterprises and organizations involved in the standardization in the U.S., Europe and Japan, the results of the R and D on 20 themes for the international standardization, and the development toward the international standardization. As the R and D themes, the following were selected: the development of chemical method to analyze/evaluate metallic coatings of surface treated steel coating sheets, R and D of the basic evaluation method of functional composite particles, international standards for computer/manikins, basic technology of color image management, study on optimizing design/evaluation technology using quality engineering, study of the international standardization by economic evaluation of environmental impacts, R and D of the standardization of a method to test acceleration life of phosphorous acid fuel cells, development of a test method of halogen-free flame-retardant cables and a study of the cable standards, standard measuring methods of hormone effects of chemical substances, quantification of the sensory evaluation and international standardization in the paint field, experimental study on the international standardization for immunochemical measurement of chemical substances, etc. 24 figs., 16 tabs.

1998 Annual Study Report. Standardization for compatibility between home information devices; 1998 nendo seika hokokusho. Joho kaden kikikan no sogo setsuzokusei kakuho no tame no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Wide-band POF covering Gbps as a Japan-made R and D fruit will be commercialized in the near future. It is very important to make an international standard specification for the transmission by the aid of the wide-band POF, which would be basically the standard for the future home networks. The efforts in this year were directed to finding the optimum parameters for widening the band, for which the necessary characteristics related to, e.g., transmission band and bending loss were measured and evaluated, and the specifications covering a certain range were established. The wide POF system is considered to provide the first chance of the optical transmission systems going into homes on a large scale, and the service conditions and regulations for use in homes have been comprehensively studied. These efforts have begun with collection of the measured data in consideration of operating optical elements represented by LD's, their peripheral circuits and the transmitter/receiver assemblies in which they are mounted at S400 or more. Each of the light emitting and receiving sections, including their peripheral circuits, were measured and evaluated, where they were mainly operated at a short wavelength of 650 nm, which is the same as that for the DVD. (NEDO)

Evaluation report on research and development of 'the comprehensive water recycling and utilization systems'; 'Mizu sogo saisei riyo system' no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-08-01

This research and development project is aimed at treatment of sewage, industrial waste water and the like at lower cost for reutilization, while efficiently producing methane or the like by the systems annexed to the water treatment systems with high-concentration bio-reactor systems incorporating separation membranes. The waste water types studied to be treated by these systems include sewage discharged in large quantities and waste water containing oil/fat and protein (low-concentration waste water), and starch-, alcohol and paper/pulp-containing waste water, and excrements (medium-concentration waste water). The project has found the optimum systems, by adequately configuring the separation membrane modules, and combining dissolution of suspended solid with methane fermentation reactors for selective treatment of organic substances; improved efficiencies of removing organic substances and producing methane by fermentation, and realized reduction in quantities of discharged sludge; and thereby established the bases for the new waste water treatment techniques. The reactor systems developed for water treatment are those based on biological removal of nitrogen. They greatly reduce treatment time to produce treated water of high quality. For treatment of sludge, the techniques have been developed to convert sludge into oil. These results are well applicable to various areas, e.g., sewage treatment, and food and pulp industries. (NEDO)

Fiscal 2000 achievement report on the development of polymeric material from renewable resource using biocatalyst; 2000 nendo seitai shokubai wo riyoshita saisei kano shigen kara no kobunshi sozai no kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The project aims to develop a biocatalyst-assisted synthesizing method for efficiently manufacturing sugar containing polymers and polylactic acids which generate less environmental impact. The ALP-901 derived from actinomycetes operates best with 5% water content, and remains free of hydrolytic effect even when the rate rises to 20%, and catalyzes transesterification only. The esterification activity of bioprase rose remarkably upon addition of water. A polymer with a molecular weight of scores of thousands was obtained in the polymerization of sugar ester monomers. A sugar undecylenate with a double bond at an end was successfully polymerized. The sugar containing polymer exhibited excellent biodegradability. In a reaction of butanediol and lactide, several types of lactic oligomers different in molecular weight were synthesized. The oligomers were caused to react with divinylcarboxylic acid in the presence of an enzyme, and a polymerizable lactic oligomer was obtained. Furthermore, in a reaction between glucose and lactide, several lactic oligomer derivatives were synthesized, different in molecular weight. In a reaction of the derivatives and divinylcarboxylic acid with an enzyme added thereto, a polymerizable lactic oligomer derivative was obtained, which was brought into polymerization in the presence of a radical polymerization initiator for the production of a high molecular weight gel. (NEDO)

Fiscal 1999 report on results. Development item, 'development of evaluation technique for biocompatibility and the like of porous materials'; 1999 nendo takozairyo no seitai tekigosei nado hyoka gijutsu no kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With the purpose of establishing fundamental technologies for ceramic porous materials that are excellent for artificial bone for a living body, evaluation technologies were developed for mechanical properties and biocompatibility, with fiscal 1999 results compiled. Performed for the examination of the mechanical properties were flexural test, compression test, tensile test, shearing test, torsion test, fatigue test, etc., with an evaluation testing method studied assuming that ceramic porous materials were applicable to implanting members. In the evaluation of biocompatibility, five kinds of osteoblast-like cell lines were cultured on a plastic disk and a dense hydroxyapatite disk, with adhesion and proliferation of the cells compared. Since these osteoblast-like cell lines adhere and proliferate on the surface and in the pore of hydroxyapatite, evaluation of the biocompatibility such as cell affinity was found possible with this in vitro method. With the view of obtaining principles for designing new bioactive ceramics, a method was developed for evaluating apatite-forming abilities of metal oxide gels having different compositions and structures in simulated body fluid. (NEDO)

Fiscal 1994 survey report. Survey of energy supply/demand structure sophistication and global environmental impact; 1994 nendo energy jukyu kozo kodoka chikyu kankyo eikyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

Outlines of various energy supply/demand analytical models are surveyed. With environmental problems gathering importance, a number of models are being introduced in which energy supply/demand structures, long-term climate changes, and impacts of policy options on social economy are linked to each other. Some socioeconomic impact models cover a single country and others the whole world. They are various in type, ranging from dynamic optimization models to static balance models. Twenty-four models are chosen, and grouped into two types respectively covering Japan and the whole world from a geographical viewpoint and into three groups in view of their structures. Under an optimization model, such optimization is accomplished as economic growth maximization and energy cost minimization and so forth under given energy supply restrictions. Under a general balance type econometric model, an adjustment process in which capital and labor and production are coordinated across multiple departments is expressly stated. Under a partial balance type econometric model, a demand function for goods is given and optimum behavior such as consumption maximization is indirectly described. (NEDO)

Engine performances and exhaust gas characteristics of methanol-fueled two-cycle engines. Kogata ni cycle ter dot methanol kikan no seino ni oyobosu shoinshi no eikyo

Energy Technology Data Exchange (ETDEWEB)

Sawa, N.; Kajitani, S. (Ibaraki Univ., Ibaraki (Japan). Faculty of Engineerineering); Hayashi, S.; Kubota, Y. (Muroran Inst. of Technology, Muroran (Japan))

1990-10-25

Regarding crank case compressed two cycle engine, feasibility of methanol-fueled engine was investigated by studying effective factors on properties of power, combustion, and exhaust gas. For the experiment, air-cooling single cylinder engine was used of which specification was shown by table. As for the experiment, quantities of in-taken air, fuel consumption, torque, and composition of exhaust gas were measured under various conditions. As the consideration of experimental results, those were obtained that less exhaust gas with high performance operation of tow-cycle engie was achieved, too, by using diluted mixture gas of methanol, and that problems were found to be studied for the realization of high compression ratio. 12 refs., 13 figs., 1 tab.

Ecological effects assessment of anionic surfactant on aquatic ecosystem using microcosm system; Microcosm wo mochiita in ion kaimen kasseizai no suiken seitaikei ni oyobosu eikyo hyoka

Energy Technology Data Exchange (ETDEWEB)

Takamatsu, Y. [University of Tsukuba, Tsukuba (Japan); Inamori, Y. [National Institute for Environmental Studies, Tsukuba (Japan); Sudo, R. [Tohoku University, Sendai (Japan). Faculty of Engineering; Kurihara, Y. [Ou Univ., Fukushima (Japan). Faculty of Engineering; Matsumura, M. [University of Tsukuba, Tsukuba (Japan). Institute of Applied Biochemical

1997-11-10

Microcosm system was applied to assess effect of anionic surfactant (LAS) on aquatic ecosystem. Anionic surfactant such as LAS was added to an flask microcosm consisting of four species of bacteria as decomposer, one species of ciliate protozoa (Cyclidium glaucoma), two rotifers (Philodina sp. and Lepadella sp.) and one aquatic oligochaete (Aeolosoma hemprichi) as predator, and a green alga (Chlorella sp.) and a filamentous blue-green alga (Tolypothrix sp.) as producer, comparing with that of an natural lake model ecosystem derived from natural lake water. In the flask microcosm system and the natural lake model ecosystem, biodegradation rates of LAS were almost same and NOECs (no observed effect concentration) of LAS were also below 1.5 mg{center_dot} l{sup -1}. It was found that flask microcosm test could provide precise ecological effect assessment of LAS on number of microorganisms because the system showed higher reproducibility and stability than natural take model ecosystem. It was suggested that flask microcosm test was useful ecological effect assessment method which can reflect natural aquatic ecosystem. 10 refs., 4 figs., 2 tabs.

Remote sensing data analysis for assessment of sea level change in Asia; Asia ni okeru kaisuijun hendo eikyo hyoka no tame no remote sensing gazo kaiseki

Energy Technology Data Exchange (ETDEWEB)

Okubo, Y; Tanaka, A [Geological Survey of Japan, Tsukuba (Japan); Kaku, M [Bishimetal Exploration Co. Ltd., Tokyo (Japan)

1997-10-22

Remote sensing images include information of coastal land division, sea level change such as sedimentary environment and vegetation, and distribution of artificial structures. Past sea level changes and their causes can be regionally obtained by analyzing these data and by integrating them with information obtained from geological survey. In this study, causes and history of past sea level changes, formation mechanism of coastal topography, and past sea level change survey in Thailand have been reviewed. This paper describes an extraction method of the sea level change information in coastal districts by analyzing several actual remote sensing images. For understanding the current sea level rise, it is required to clarify the causes quantitatively among three causes of sea level changes, i.e., volumetric change of total ocean water on the earth, relative sea level change due to the crustal deformation, and change of irregularity of sea surface with ocean current. It is also required to compile maps in Asian or global scales. 13 refs., 6 figs.

Method for estimation of the spectral distribution that influence electric power of PV module; Taiyo denchi shutsuryoku ni eikyo wo ataeru bunko nissha bunpu no suiteiho

Energy Technology Data Exchange (ETDEWEB)

Yamagami, Y.; Tani, T. [Science University of Tokyo, Tokyo (Japan)

1997-11-25

A method was proposed for estimating the spectral distribution using air mass, precipitable water, and clear indexes which are generally obtainable, and a comparative study was made between the spectral distribution obtained by this method and the measured data using output power of PV modules, etc. as indexes. When solar light comes into the atmosphere, it dissipates receiving scattering/absorption by various gases and aerosols. Direct light component and scattered light component which arrive at the earth surface become functions of air mass and precipitable water. The wavelength distribution of scattered light in cloudy sky is not dependent upon air mass, but affected strongly by absorption band by steam of clouds. By relational equations considered of these, output power and short-circuit current of PV modules are obtained to make a comparison with the measured data. As a result, it was found that this method estimated the spectral distribution with accuracy. Further, seasonal changes in the spectral distribution were well reproduced. The simulation of the module output in Sapporo and Okinawa brought a result that the output in Okinawa is 1.93% larger than in Okinawa. 5 refs., 5 figs., 6 tabs.

Changes in soil organisms by the application of sludge composits, and their effects. Odei taihirui no shiyo ni tomonau dojo seibutsu no henka to sono eikyo

Energy Technology Data Exchange (ETDEWEB)

Niijima, K.; Fujita, K.; Ogawa, M. (Forestry and Forest Products Research Institute, Tsukuba (Japan))

1993-08-31

With an objective to utilize sewage sludge more effectively, composted sewage sludge has been applied to seed beds to investigate its effect on soil macrofauna and higher fungi, and its relativity with change in soil organisms, growth of young trees, and soil science. Forty-eight seedling sections, each 5 m [times] 5 m, were made on a seed bed which was applied with Tenryu sludge composts (polymer-based coagulant), several other kinds of sludge composts, fallen leaf composts, and cattle excrement composts at predetermined rates from zero to 20 kg. Each section was planted with 25 three-year-old nursery trees of a kind of oak, black pine, and cypress. As a result, the following findings were obtained: wet weight of larvae of Japanese gold beetles that attack tree roots has increased during the first and second years in the Tenryu sludge applied section, but no longer increased in the third year; the relationship between the other composts and soil macrofauna was not made clear; Scleroderma Cepa PERS, a mycorrhiza bacteria, has been generated in the oak planted section in the second, third and fourth years, with the second year particularly having generated it in a greater amount in proportion with the fertilizer application amount, but the fertilizer effect thereafter is not clear. 24 refs., 6 figs., 9 tabs.

Effects space velocity and gas velocity on DeNOx catalyst with HC reductant; HC tenka NOx kangen shokubai no kukan sokudo oyobi gas ryusoku no eikyo

Energy Technology Data Exchange (ETDEWEB)

Niimura, K.; Tsujimura, K.

1995-04-20

Discussions were given on the hydrocarbon added reduction catalyst method to reduce NOx in diesel engine exhaust gas. An experiment was carried out with actual exhaust gas from a diesel engine by using a copper ion exchanged zeolite catalyst that has been coated on a honeycomb type substrate, and using propylene as a reductant. When the catalyst volume was changed with the exhaust gas space velocity kept constant, the NOx conversion ratio decreased as the catalyst length is decreased, and the activity shifted to the lower temperature side. The NOx reduction efficiency increased if the faster the gas flow velocity. On the other hand, if the gas flow velocity is slow, the NOx reduction can be carried out with relatively small amount of the reductant. When the catalyst volume was changed with the passing gas amount kept constant, the NOx conversion ratio decreased largely if the catalyst length is decreased. Further, the NOx reduction characteristics shift to the higher temperature side. In the catalyst length direction, the NOx reduction activity shows a relatively uniform action. However, a detailed observation reveals that the reaction heat in the catalyst is transmitted to the wake improving the activity, hence the further down the flow, the NOx conversion ratio gets higher in efficiency. 5 refs., 5 figs., 3 tabs.

Report for fiscal 2000 investigations on effects imposed by introducing emission trading system; 2000 nendo haishutsuryo torihiki system donyu ni yoru eikyo ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With regard to effectiveness of the emission trading targeted to reduce the greenhouse effect gas emission, evaluation has been given from the three viewpoints: economies, environment, and household economy. In the research, simulations were implemented by using the GEC calculation model modified for introduction of domestic emission trading, and utilization of international emission trading. In evaluating the effects on industries and foreign trades, notice was given on the large energy consuming industries to discuss the effects of introducing the emission trading on the quantity of production and export. Regarding the effects on environment, calculations and discussions were given on greenhouse effect gas leakage rates to assess the greenhouse effect gas emission reducing effects from the domestic and international viewpoints. As a result of the discussions, it was found that the economies, environment and household economy are all benefited in regard with the domestic emission trading. Utilization of the international emission trading was also found to have sufficient positive benefit exist for the economies and household economy. (NEDO)

Influence of strain hardening and thickness changes occurring in press forming process; Seikeiji no kako koka/itaatsu henka no buzai akkai tokusei ni oyobosu eikyo bunseki

Energy Technology Data Exchange (ETDEWEB)

Ueno, M; Hirota, K [Mazda Motor Corp., Hiroshima (Japan); Nakazawa, Y [Sumitomo Metal Industries Ltd., Osaka (Japan)

1997-10-01

Most components of the body structure are produced by press forming. This process make a uniform metal sheet into a component that have various material characteristics and thickness. This paper describes the estimation method of material characteristics and thickness changes based on the measured Vickers hardness, and the influence of these changes on the crush performance by using FE analysis. 4 refs., 12 figs., 2 tabs.

Effect of laser heat treatment on intergranular corrosion of austenitic stainless steel; Austenite kei stainless ko no ryukai fushoku kanjusei ni oyobosu laser netsushori no eikyo

Energy Technology Data Exchange (ETDEWEB)

Osawa, M.; Yoneyama, T. [Tokyo Denki University, Tokyo (Japan). Faculty of Engineering; Isshiki, Y. [Tokyo Metropolitan Industrial Technology Center, Tokyo (Japan)

1995-03-15

The laser heat treatment of SUS304 steel was studied to lower the intergranular corrosion sensitivity of austenitic stainless steel. By the short-time heating around 923K, the SUS304 steel is sensitized to the intergranular corrosion with the deposition of Cr carbide into the granular field of crystals. To recover it, it is necessary to solidly dissolve, and simultaneously, quickly cool the Cr carbide above 1273K. For such solution heat treatment, CO2 laser beams were used with the treatment condition that the power and beam diameter were 800 to 1200W and 0.3 to 0.64cm, respectively. Regardless of both power density and beam diameter, the desensitization was observed at heating temperatures above 1323K. As a result of calculation by simulation, the solid dissolution of Cr carbide and recovery of Cr`s depletion zone in the granular field of crystals took place in a very short time at heating temperatures above 1323K. It agreed well with the experimental result. The laser beams are effective in the solution heat treatment of stainless steel. 14 refs., 15 figs., 1 tab.

Effect of fish on water quality and nutrients cycle from an outdoor pond experiment; Sakana no suishitsu, busshitsu junkan ni oyobosu eikyo ni kansuru jikkenteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Fukushima, T.; Matsushige, K.; Aizaki, M. [National Inst. for Environmental Studies, Tsukuba (Japan); Park, J.; Goma, R. [Tokyo University of Fisheries, Tokyo (Japan); Kong, D. [Korea National Institute of Environmental Research, Seoul (Korea, Republic of)

1995-11-10

The influences of fish (goldfish) on water quality and nutrients cycle (carbon, nitrogen, phosphorus) were investigated during 39 days in the summer of 1993, using six outdoor experimental ponds (36 m{sup 3}) with the same water residence times and nutrient inputs. Blue-been algae dominated the ponds with fish. Compared with ponds without fish, the ponds with high densities of fish had standing stocks of zooplankton and macrozoobenthos nearly one order of magnitude lower, about twice the concentrations of chlorophyll a and twice the rate of primary production. Settling rates of particulate substances in the high density ponds were nearly half those observed in ponds with no fish. The processes of sedimentation and exchange with air played important roles in the nutrient budgets as well as the in- and outflows and the changes in nutrient standing stocks. The high concentrations of chlorophyll a in the fish ponds were attributed in part to the lower zooplankton grazing pressure and in part to the higher nutrient concentrations due to lower settling rates and rapid nutrient recycling between biomass and dissolved components. 28 refs., 8 figs., 6 tabs.

1998 Annual Study Report. New industry supporting type international standard development program (Comprehensive survey); 1998 nendo seika hokokusho. Shinki sangyo shiengata kokusai hyojun kaihatsu jigyo (sogo chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Summarized herein are results of the survey on a total of 13 themes for international standardization. These themes are for standardization of (1) color control, (2) securing interoperability between optical disk systems, (3) digital image processing for home digital electronic appliances, (4) securing interconnectability between home electronic information appliances, (5) production process systems, (6) testing and evaluation methods for fine ceramic materials for communications, (7) evaluation methods for high-temperature properties of new glass melts, (8) corrosion testing and evaluation methods for surface-treated steel plates, (9) testing and evaluation methods for high-purity titanium, (10) testing and evaluation methods for plastic optical fibers, (11) evaluation methods for high-strength, large-size steel pipe characteristics for superhigh-pressure natural gas pipelines, (12) methods for measuring mileage of hybrid electric vehicles, and (13) methods for determining recycle ratios of automobile components. This comprehensive survey also includes overseas trends for the standardization, establishment/expansion of the international standardization processes, and standardization for determining recycle ratios of home electric appliances. (NEDO)

Characterization of interactions of coal surface with solvent by flow microcalorimetric measurement. 3; Netsuryo sokutei ni yoru sekitan hyomen to yozai tono sogo sayo no hyoka. 3

Energy Technology Data Exchange (ETDEWEB)

Wang, N.; Sasaki, M.; Yoshida, T. [Hokkaido National Industrial Research Institute, Sapporo (Japan); Kotanigawa, T. [Japan International Corporation Agency, Tokyo (Japan)

1996-10-28

An investigation was given on the relationship between methanol adsorbing behavior of reformed coal surface and oxygen containing functional groups in coal. Akabira bituminous coal was air-oxidized or Yallourn brown coal was decarbonated in oil as a reformation treatment. Both of the treated and untreated coals showed an adsorption heat curve of the Langmuir type. The Akabira coal had its oxygen content and the adsorption heat increased as a result of the air oxidizing reformation treatment. The Yallourn coal had its oxygen content and adsorption heat decreased as a result decarbonation reformation treatment. Oxygen containing functional groups act as strong adsorption sites for methanol, and the maximum adsorption amount depends on oxygen content in the coals. Since the coal surface is non-uniform in terms of energy, methanol is adsorbed first into sites with higher molar adsorption heat, and then into lower sites sequentially. Therefore, distribution of the molar adsorption heat can be derived from the relationship between adsorption amount and adsorption heat by changing methanol adsorption amount. The distribution of molar adsorption heat becomes broader when the oxygen content is high, and narrower when low. 2 refs., 2 figs.

Review of an analysis system of `Long-Term Deep Seafloor Observatory off Muroto Peninsula`; Kochiken Murotomisakioki `kaitei jishin sogo kansoku system` data no kaiseki system no shokai

Energy Technology Data Exchange (ETDEWEB)

Tsuru, T; Machiyama, H; Hattori, M; Kaneda, Y [Japan Marine Science and Technology Center, Kanagawa (Japan)

1997-10-22

Introduced is a data analysis system for Long-Term Deep Seafloor Observatory established off Muroto Point by Japan Marine Science and Technology Center (JAMSTEC), from which observatory data collected by seismograph and tsunami-meter are transmitted real time. JAMSTEC Long-Term Deep Seafloor Observatory Project Team has begun constructing an analysis system for disposing of events in the data and for locating the hypocenter. The analysis system is composed of a data converting unit that converts the forwarded data into the Win format; a data storage/time-dependent data integration unit that keeps the data in a hard disk for a specified period of time, performs disposition and analysis of events in the data, and forwards the data after disposition and analysis to a data recording unit; a data recording unit that stores selected data of seismic events in a recording medium; and a real-time monitor/NTP server unit that displays real time the observed seismic waveform data. 2 figs.

On the sea-covering effect of a huge floating structure on the surrounding water; Choogata futai shuhen no kaisui ni taisuru kaimen shahei no eikyo ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Fujino, M; Kagemoto, H; Hamada, T [The University of Tokyo, Tokyo (Japan)

1997-12-31

The numerical analysis program based on the difference method for dynamics of sea water with sea-surface displacement, flow rate, salt content and temperature as the parameters is modified to more accurately assess the effects of a huge marine structure on surrounding environment by adding the effects of insolation and boundary conditions of the sea-covering effects of the floating structure. The numerical simulation was done for summer and winter seasons, not in a sea area but using a rectangular bay with the floating structure at the center. A new flow evolves around the floating structure, due to the sea-covering effect. The flow patterns in summer and winter are clearly different, due to difference in insolation. The predicted flow is also sensitive whether stratification is considered or not, by which is meant that it is important what stratification effect is taken into account. Daily insolation changes are accompanied by vertical distribution of water temperature and its temporal change. These effects are also observed under the floating structure which shields insolation. 10 refs., 17 figs., 4 tabs.

Studies on surface tension effect for free surface flow around floating models; Futai mokei mawari no jiyu hyomenryu ni oyobosu hyomen choryoku no eikyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Suzuki, K [Yokohama National Univ., Yokohama (Japan). Faculty of Engineering; Akiba, H [Toyo Construction Co. Ltd., Tokyo (Japan)

1997-12-31

The effect of surface tension on free surface flow around floating models is discussed experimentally and numerically. Three-dimensional free surface flow around vertical circular cylinders floating in a circulating water channel was visually observed, where a surface-active agent was added to water. The results are analyzed using Weber number. The numerical analysis was done for vertical cylinder and CY100 models using the Rankine source method. Weber number of at least around 120 is necessary to eliminate the effect of surface tension from free surface flow around the CY100 model. The numerical analysis for the cylinder model needs simulation with wavelength shorter than that of free surface wave used by the Rankine source method. The model for the resistance test should be at least around 7m long to eliminate the effect of surface tension at Froude number of 0.1 or higher. 15 refs., 12 figs., 2 tabs.

Coliquefaction of coal, tar sand bitumen and plastic (interaction among coal, bitumen and plastic); Sekitan/tar sand bitumen/plastic no kyoekika ni okeru kyozon busshitsu no eikyo

Energy Technology Data Exchange (ETDEWEB)

Yamaguchi, H.; Okuyama, Y.; Matsubara, K. [NKK Corp., Tokyo (Japan); Kamo, T.; Sato, Y. [National Institute for Resources and Environment, Tsukuba (Japan)

1996-10-28

For the improvement of economy, coliquefaction of coal, tar sand bitumen and plastic was performed under low hydrogen pressure, to investigate the influence of interaction among these on the liquefaction characteristics. For comparison, coliquefaction was also performed under the hydrogen pressure same as the NEDOL process. In addition, for clarifying its reaction mechanism, coliquefaction of dibenzyl and plastic was performed as a model experiment, to illustrate the distribution of products and composition of oil, and to discuss the interaction between dibenzyl and various plastics, and between various plastics. Under direct coal liquefaction conditions, coprocessing of Tanito Harum coal, Athabasca tar sand and plastic was carried out under low hydrogen pressure with an autoclave. The observed value of oil yield was higher than the calculated value based on the values from separate liquefaction of coal and plastic, which suggested the interaction between coal and the mixed plastic. The results of coliquefaction of coal, tar sand bitumen and plastic could be explained from the obtained oil yield and its composition by the coliquefaction of dibenzyl and plastic. 2 refs., 3 tabs.

Wall effect in deactivation of excited molecular oxygen {sup 1}{delta}g; Reiki sanso bunshi {sup 1}{delta}g no shikkatsu ni oyobosu hyomen hanno no eikyo

Energy Technology Data Exchange (ETDEWEB)

Takahashi, S.; Hasegawa, Y.; Yamashita, I. [Mechanical Engineering Laboratory, Tsukuba (Japan)

1993-10-25

This paper discusses effects of surface reaction on deactivation of excited molecular oxygen in {sup 1}{Delta}g condition. Gaseous oxygen containing excited oxygen generated by microwave discharge at a concentration of less than 1% is flown into several kinds of tubes to be measured such as quartz tubes (with an inner diameter of about 10 mm), and the light emitting intensity of the excited oxygen was measured upstream and downstream of the tubes to be measured (with in-tube pressure of 1 Torr or 2 Torr) to derive its concentration change. The surface reaction on the tube wall was regarded as a primary reaction, and the concentration change of the excited oxygen in flows in the round tube (attributable to the surface reaction) was analyzed. With respect to effects of tube wall materials on deactivation of the excited molecular oxygen, the surface deactivation probability in the case of using low-activity materials has decreased in the order of Pyrex, PVC, quartz, PFA and PTFE. The surface deactivation probability in the case of using a metallic material, SUS316L, was about 1000 times larger than that in the quartz. 14 refs., 7 figs., 1 tab.

Effect of grain size on amplitude-dependent internal friction in polycrystalline copper. Do takessho no naibu masatsu no shinpuku izon sei ni oyobosu kessho ryukei no eikyo

Energy Technology Data Exchange (ETDEWEB)

Goto, H.; Nishino, Y.; Asano, S. (Nagoya Inst. of Technology, Nagoya (Japan))

1991-08-20

In this research, amplitude-dependency of internal friction was measured on various polycrystalline copper of varying grain size. Furthermore, the measurement data of amplitude-dependency of internal friction were analyzed from the phenomenological standpoint and microplastic strain was calculated as a function of stress. The obtained correlation between microplastic strain and stress corresponded to the stress-strain curve obtainable from normal tensile tests. Hence, comparing with the Hall-Petch relation, the relationship between flow stress and grain size in the microplastiic zone was discussed. The obtained results are summarized as follows: When grains were refined, amplitude dependency of internal friction was inhibited. As a result of the analysis of the data obtained, it was found that the flow stress in the microplastic zone increased following refining of grains. This agreed qualitatively with the macro deformation obtained from normal tensile tests. The grain size dependency of flow stress in the microplastic zone did not follow the normal Hall-Pitch relation, but the plastic strain increased, the dependency moved towards it. 16 refs., 4 figs.

Fiscal 1998 survey report. Survey on method of environmental-impact assessment in wind power development; 1998 nendo furyoku kaihatsu ni okeru kankyo eikyo hyoka shuho chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

With the purpose of preparing the main points of 'environmental-impact assessment guidelines for wind power developments (draft)', examples of environmental-impact assessments, related laws and regulations in Japan and abroad were collected, and rearranged in respect to requirements in environmental-assessments, concrete procedures, survey/projection/assessment method, summarisation of results, etc. It was clarified, for example; in a large-scale wind power development, it can be dealt with by choosing items and contents on the assumption that a land area is developed; in a small-scale development, there is basically no need of considering the possible effect of the construction work; and, as far as noise, vibration and the ecosystem (plants/animals) are concerned, however, the characteristics of the site be taken into consideration. Objects for general assessment are noise, low-frequency air vibration, radio wave interference, the ecosystem (plants and animals) and the landscape. The guideline draft is constituted of (1) basic items, (2) overview of the area, (3) determination of items for environmental-impact assessment and (4) research, prediction, assessment, conservation measures and follow-up research; in the basic items, importance of preliminary consideration was emphasized, as were priority/simplification, implementation of environmental conservation measures, and implementation of follow-up research. (NEDO)

On the sea-covering effect of a huge floating structure on the surrounding water; Choogata futai shuhen no kaisui ni taisuru kaimen shahei no eikyo ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Fujino, M.; Kagemoto, H.; Hamada, T. [The University of Tokyo, Tokyo (Japan)

1996-12-31

The numerical analysis program based on the difference method for dynamics of sea water with sea-surface displacement, flow rate, salt content and temperature as the parameters is modified to more accurately assess the effects of a huge marine structure on surrounding environment by adding the effects of insolation and boundary conditions of the sea-covering effects of the floating structure. The numerical simulation was done for summer and winter seasons, not in a sea area but using a rectangular bay with the floating structure at the center. A new flow evolves around the floating structure, due to the sea-covering effect. The flow patterns in summer and winter are clearly different, due to difference in insolation. The predicted flow is also sensitive whether stratification is considered or not, by which is meant that it is important what stratification effect is taken into account. Daily insolation changes are accompanied by vertical distribution of water temperature and its temporal change. These effects are also observed under the floating structure which shields insolation. 10 refs., 17 figs., 4 tabs.

Studies on surface tension effect for free surface flow around floating models; Futai mokei mawari no jiyu hyomenryu ni oyobosu hyomen choryoku no eikyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Suzuki, K. [Yokohama National Univ., Yokohama (Japan). Faculty of Engineering; Akiba, H. [Toyo Construction Co. Ltd., Tokyo (Japan)

1996-12-31

The effect of surface tension on free surface flow around floating models is discussed experimentally and numerically. Three-dimensional free surface flow around vertical circular cylinders floating in a circulating water channel was visually observed, where a surface-active agent was added to water. The results are analyzed using Weber number. The numerical analysis was done for vertical cylinder and CY100 models using the Rankine source method. Weber number of at least around 120 is necessary to eliminate the effect of surface tension from free surface flow around the CY100 model. The numerical analysis for the cylinder model needs simulation with wavelength shorter than that of free surface wave used by the Rankine source method. The model for the resistance test should be at least around 7m long to eliminate the effect of surface tension at Froude number of 0.1 or higher. 15 refs., 12 figs., 2 tabs.

Achievement report for fiscal 1998. Development of Assessment Technology of Life Cycle Environment Impacts of Products; 1998 nendo seika hokokusho. Seihinnado lilfecycle kankyo eikyo hyoka gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

An inventory data collecting format is formulated, data collecting activities are launched through 23 industry associations and several investigatory agencies, and almost all the primary data are collected. All the inventory items are being rearranged into a convenient order, and efforts are under way to designate the association to be in charge and the method to be used for data collecting (the accumulation method, process model method). Problems about techniques in the veinous department are extracted. The flow of matters relating to various metals and glass after their use and the magnitude of their environmental impacts at the ultimate sites of treatment are understood though roughly. Investigations are conducted into typical formats overseas, a data arranging format is constructed, specifications are defined for a data inputting software program, and a request is placed with a dedicated dealer for the compilation of the said program. The architecture and specifications of an LCA (life cycle assessment) database system are determined, and its functions are undergoing an intermediate check by a research team for improvement. Endeavors are exerted at quantifying global warming, ozone layer depletion, biotoxicity, and photochemical oxidants for use as the basic data for damage evaluation. (NEDO)

Investigation of local-dimensional galvanic distortion on MT data in the central part of Northeastern Japan; Tohoku chiho no MT data ni mirareru kyokushoteki sanjigensei no eikyo

Energy Technology Data Exchange (ETDEWEB)

Kawakami, N; Takasugi, S [GERD Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan); Fujinawa, Y [National Research Institute for Disaster Prevention, Tsukuba (Japan)

1996-10-01

Groom-Bailey decomposition analysis was carried out to investigate regional 3-D galvanic distortion on MT data in the central part of Northeastern Japan. Measuring sites were located nearly along the east-west line crossing Northeastern Japan. Three measuring lines (A, B, C) from the north to the south were prepared, and only data on the C line were analyzed in this paper. As a result, twist and shear were estimated to be not zero depending on local distortion in most of the sites. It was thus clarified that this method is not always perfect. This method was effective for regional 2-D structures, however, its application was doubtful to complicated 3-D underground structures in Japan. In order to obtain more accurate results, 2-D analysis using the impedance including no local distortion effect was necessary after the preliminary Groom-Bailey decomposition analysis. The direction of the wide area geological structure of Northeastern Japan was estimated to be N-S direction near NNW-SSE one. 6 refs., 12 figs., 1 tab.

Fiscal 1998 survey report. Survey on method of environmental-impact assessment in wind power development; 1998 nendo furyoku kaihatsu ni okeru kankyo eikyo hyoka shuho chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

With the purpose of preparing the main points of 'environmental-impact assessment guidelines for wind power developments (draft)', examples of environmental-impact assessments, related laws and regulations in Japan and abroad were collected, and rearranged in respect to requirements in environmental-assessments, concrete procedures, survey/projection/assessment method, summarisation of results, etc. It was clarified, for example; in a large-scale wind power development, it can be dealt with by choosing items and contents on the assumption that a land area is developed; in a small-scale development, there is basically no need of considering the possible effect of the construction work; and, as far as noise, vibration and the ecosystem (plants/animals) are concerned, however, the characteristics of the site be taken into consideration. Objects for general assessment are noise, low-frequency air vibration, radio wave interference, the ecosystem (plants and animals) and the landscape. The guideline draft is constituted of (1) basic items, (2) overview of the area, (3) determination of items for environmental-impact assessment and (4) research, prediction, assessment, conservation measures and follow-up research; in the basic items, importance of preliminary consideration was emphasized, as were priority/simplification, implementation of environmental conservation measures, and implementation of follow-up research. (NEDO)

Effect of release sheet on the preparation of CF paper/aluminium phosphate composite; Tanso sen`i paper/rinsan aluminium fukugo zairyo choseiji ni okeru hakurizai no eikyo

Energy Technology Data Exchange (ETDEWEB)

Hoshii, S.; Kojima, A. [Gunma National College of Technology, Gunma (Japan); Otani, S. [Tokai University, Tokyo (Japan). School of High-Technology for Human Walfare

1995-12-27

A composite material was prepared with carbon fiber (CF) and a matrix of phosphate (as named ACP) mainly consisting of aluminum phosphate. CF was used in the form of felt cloth. Prepreg was made with CF and ACP, which was laminated and formed under pressure in a hot press into a composite. The prepreg was pretreated by drying at 80{degree}C to form a compact matrix and to increase the adhesion between laminated prepregs. At the hot press treatment thorough removal of water was tried by using absorbent sheet and release sheet to form a compact structure. Consequently, porosity of CF/ACP composite decreased, and its bulk density and bending strength increased. SEM observation showed the formation of vitreous and compact matrix. Besides, adhesion between prepregs and shear fracture resistance were improved. 24 refs., 3 figs., 3 tabs.

Effect of separation and drainage of condensate on dehumidification in a refrigerated dryer; Reito joshitsuki ni okeru gyoshukusui bunri/haishutsu noryoku no joshitsu seino ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Goto, H.; Ichinose, T. [SMC Corp., Tokyo (Japan); Tanzawa, Y.; Hashizume, T. [Waseda Univ., Tokyo (Japan). Science and Engineering Research Lab.

1995-11-15

The representative refrigerated dryer as the compressed air dryers is one in which air was cooled at rather low temperature by working medium of refrigerators, and the dew point was decreased with increase of pressure, and air with low relative humility called as the dried air was obtained again by heating. In this paper, for clarifying effect of separation and drainage of condensate on dehumidification in a refrigerated dryer in relation to shape of a main cooler and a precool-reheater and air temperature of each part, calculation and experimental investigation were conducted. In a refrigerated dryer, condensate happened in the precool part of a precool-reheater and a main cooler, and this would give rise to reduce of separation and drainage of condensate and increase of thermal loads of each heat exchange, and would made dehumidification low. For a fact that decrease of separation and drainage of condensate in a main cooler would bring out heat conduction with phase change in the reheating part of a precool-reheater, it has a profitable side, but it is not desirable for ability of dryers. 6 refs., 9 figs., 1 tab.

Fiscal 2000 research report on the study on management program for comprehensive assessment of chemical materials; 2000 nendo kagaku busshitsu sogo hyoka kanri program ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the realization of environmentally friendly, sound economic activities and the assurance of a safe and peaceful daily life for people, studies were conducted about comprehensive risk assessment and management techniques to use in dealing with chemical substances. Concerning the above-named management program, a workshop was called, where panel discussion and exchange of views and opinions were held. In the study of overseas technological trends, visits were paid to interested institutes and corporations in Denmark, Sweden, and Germany, where hearings were held over the management and manufacture of chemical substances. Concerning the control of chemical substances, surveys were conducted of the control in Japan and abroad and of the methods that businesses and other organizations followed in meeting the control. It was found that the control was being dealt with earnestly in every country and that chemical substances would stay managed under international collaborative conditions. Efforts were being positively exerted by businesses and other organizations to properly manage and reduce chemical substances and to develop and use substitutes. It was found that measures for handling chemical substances were closely knit into business management. (NEDO)

Evaluation report on research and development of a database system for mutual computer operation; Denshi keisanki sogo un'yo database system no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-01

This paper describes evaluation on the research and development of a database system for mutual computer operation, with respect to discrete database technology, multi-media technology, high reliability technology, and mutual operation network system technology. A large number of research results placing the views on the future were derived, such as the issues of discretion and utilization patterns of the discrete database, structuring of data for multi-media information, retrieval systems, flexible and high-level utilization of the network, and the issues in database protection. These achievements are publicly disclosed widely. The largest feature of this project is in aiming at forming a network system that can be operated mutually under multi-vender environment. Therefore, the researches and developments have been executed under the spirit of the principle of openness to public and international cooperation. These efforts are represented by organizing the rule establishment committee, execution of mutual interconnection experiment (including demonstration evaluation), and development of the mounting rules based on the ISO's 'open system interconnection (OSI)'. These results are compiled in the JIS as the basic reference model for the open system interconnection, whereas the targets shown in the basic plan have been achieved sufficiently. (NEDO)

Fiscal 1999 report on results. Development item, 'development of evaluation technique for biocompatibility and the like of porous materials'; 1999 nendo takozairyo no seitai tekigosei nado hyoka gijutsu no kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With the purpose of establishing fundamental technologies for ceramic porous materials that are excellent for artificial bone for a living body, evaluation technologies were developed for mechanical properties and biocompatibility, with fiscal 1999 results compiled. Performed for the examination of the mechanical properties were flexural test, compression test, tensile test, shearing test, torsion test, fatigue test, etc., with an evaluation testing method studied assuming that ceramic porous materials were applicable to implanting members. In the evaluation of biocompatibility, five kinds of osteoblast-like cell lines were cultured on a plastic disk and a dense hydroxyapatite disk, with adhesion and proliferation of the cells compared. Since these osteoblast-like cell lines adhere and proliferate on the surface and in the pore of hydroxyapatite, evaluation of the biocompatibility such as cell affinity was found possible with this in vitro method. With the view of obtaining principles for designing new bioactive ceramics, a method was developed for evaluating apatite-forming abilities of metal oxide gels having different compositions and structures in simulated body fluid. (NEDO)

FY 1998 achievement report on the R and D project on industrial science technology. Development of a functional biomolecule analysis/synthesis system; 1998 nendo kinosei seitai bunshi kaiseki gosei system no kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of developing the technology required for the biotechnology industry, a study was made on proteins having ligand recognition function, and the FY 1998 results were reported. In the technology development of a system for various/diversified syntheses of functional molecules, a system was designed/trially manufactured which enables the simultaneous synthesis of various biological/functional substances (compound library) at high-efficiency. In the development of the structure analysis system of ligand recognized proteins, a high-efficient biopolymer analysis system was developed which is based on TOF (time-of-flight) mass spectrometer and analyzes proteins produced by recombined genes quickly and precisely. In the R and D of functional molecules using ligand recognized proteins, the cloning was successfully made of the human estrogen receptor gene hER {alpha}, which is composed of 1,785 bp, from MCF-7-BOS. Further, the bioassay system for estrogen-like substances using MCF-7 cells was established. (NEDO)

FY 2000 report on the survey for introduction of the hot spring effect prediction method in the geothermal development promotion survey. Improvement of the hot spring effect prediction method in the geothermal development promotion survey; 2000 nendo chinetsu kaihatsu sokushin chosa. Onsen eikyo yosoku shuho donyu chosa - Chinetsu kaihatsu sokushin chosa ni okeru onsen eikyo yosoku shuho no kairyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Supposing the case where the geothermal development promotion survey was carried out in promising geothermal areas in Japan, investigational study was conducted on possibilities of introducing the hot spring effect prediction method, improvement of the method, etc. In the survey, adjustment/classification of formation mechanisms of hot spring were made. For each of the formation mechanisms, the mechanisms in case of the geothermal development having effects were studied/summarized. As to how effects are brought about, presumed were the lowering of water level and decrease in discharge amount in accordance with the decreasing pressure and the dilution by increase in mixture of the ground water around the area. Also cited were the vaporization of hot spring aquifers by the increasing rate of vapor inflow, etc. For the introduction of the hot spring effect prediction method to the geothermal development promotion survey, the problem is short supply of various data, and the examination for it was made. Based on the results of the survey, items to be studied in case of introducing the hot spring effect prediction method were selected. Further, the hot spring effect prediction flow in case of introducing surface survey and well survey was made out. (NEDO)

FY 2000 report on the survey of effects of enhancement of energy consumption efficiency on the global environment; 2000 nendo energy shohi koritsuka chikyu kankyo eikyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Looking for effective measures for enhancement of energy consumption efficiency in the Asia Pacific region, survey was made of the state of study of measures against global warming in the 3rd IPCC report and the state of study of the incidental convenience. The survey was made in the following two fields: 1) research analysis in study of the 3rd IPCC report; 2) research analysis of the convenience incidental to measures against global warming. 1) is composed of IPCC activities and the 3rd assessment report, and the developmental state of global warming prevention technology and potential of greenhouse effect gas reduction. Subjects on the prevention technology are the technology for enhancement of energy consumption and development of non-fossil fuels. Physical/chemical CO2 fixation is also studied. 2) is composed of the introduction, economic/social/environmental effects, international flow, reasons for different conclusion in every study, and fields of further study. Considered were global warming prevention measures, for example, economic/social/environmental effects of creation of the carbon tax, reduction in subsidy in energy sector, etc. (NEDO)

Report on achievements in fiscal 1998. Survey on environmental effects from photovoltaic power generation systems; 1998 nendo daikibo taiyoko hatsuden system no kankyo eikyo ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Different environmental effects may be assumed when large-size photovoltaic power generation systems are installed in vast unutilized lands including deserts. Knowledge having been acquired to date has been put into order on the following subjects as the pre-survey thereon: (1) environmental characteristics of desert areas, (2) discussions on environmental effects from (a) environmental assessment viewpoints, (b) contents of the environmental assessment, and (c) environmental assessment institutions, and (3) the survey policy. In discussing the environmental characteristics, it is revealed that desert areas are neither sterile nor unused, but pasturage and agriculture have been carried out in historical and traditional ways. In discussing the environmental effects, it was recognized that surveys on primary and secondary effects on the environmental are indispensable. With regard to the institutions, there are countries who have and have not the institutions even among the OECD member states. In addition, it was known that environments in the desert areas vary greatly according to the particular areas, whereas there are possibilities of installing the facilities because the effects of the facility locations on the environment are various. Therefore, it was decided to start from the case studies in locations of different types. (NEDO)

Influence of catalytic activity and reaction conditions on the product distribution in coal liquefaction; Sekitan ekikayu no seiseibutsu bunpu ni taisuru shokubai kassei oyobi hanno joken no eikyo

Energy Technology Data Exchange (ETDEWEB)

Hasuo, H.; Sakanishi, K.; Mochida, I. [Kyushu University, Fukuoka (Japan). Institute of Advanced Material Study

1996-10-28

The NiMo sulfide supported on Ketjen Black (KB) was more effective and yielded lighter oil products containing light fractions with their boiling point below 300{degree}C during the two stage liquefaction combining low temperature and high temperature hydrogenation the conventional NiMo/alumina catalyst and FeS2 catalyst. Although the NiMo/alumina yielded increased oil products during the two stage liquefaction, the lighter oil fractions did not increase and the heavier fractions increased mainly. This suggests that the hydrogenation of aromatic rings and successive cleavage of the rings are necessary for producing the light oil, which is derived from the sufficient hydrogenation of aromatic rings using catalysts. For the two stage reaction with NiMo/KB catalyst, it was considered that sufficient hydrogen was directly transferred to coal molecules at the first stage of the low temperature reaction, which promoted the solubilization of coal and the successive hydrogenation at the high temperature reaction. Thus, high activity of the catalyst must be obtained. It is expected that further high quality distillates can be produced through the optimization of catalysts and solvents at the two stage reaction. 1 ref., 4 figs., 1 tab.

Assessment of a Mega-Float on water quality and ecosystem in Tokyo bay; Choogata futaishiki kaiyo kozobutsu ga Tokyowan no suishitsu to seitaikei ni oyobosu eikyo ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Kyozuka, Y.; Hu, C.; Hasemi, H. [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Hikai, A.

1997-08-01

The effect on the marine environment in the bay when a Mega-Float is installed in a bay was investigated. The physical process such as a residual flow (including tidal currents, water temperature, salt, density, and density currents), and the ecosystem model for which floating organic matter and plankton are handled were incorporated to develop a program for water quality calculation in a bay. The program was used for Tokyo Bay and compared with the conventional calculation result and the oceanograhpic observation result. Simultaneously, the effect on the Mega-Float was considered. On the flow in Tokyo Bay in summer, the calculation result that comparatively coincided with the observation value in a residual flow level was obtained. The horizontal distribution of COD comparatively coincides with the existing observation result. The influence that the Mega-Float exerts on the flow, water temperature, water quality, and ecosystem in the ambient sea area was little and local in the calculation scale (L {times} B {times} d = 6 km {times} 3 km {times} 2 m) of this time. However, the difference occurring due to the design position must also be investigated in future. 12 refs., 8 figs., 5 tabs.

1998 Annual Study Report. Standardization for securing interoperability between optical disk systems; 1998 nendo seika hokokusho. Hikari disk system no sogo un'yosei kakuho no tame no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This R and D program is aimed at securing interoperability between optical disk systems, based on the logical formats, to propose the draft international standards. For the volume/file structures proposed by ISO/IEC 13346, the universal disk format (UDF) proposed by the Optical Storage Technology Association (OSTA) is taken as the target file system, to improve the conformance test environments and develop the standards for advanced interoperability. The 1998 R and D themes include development of the UDF conformance testing tools for avoiding the interoperability-related problems involved in the UDF, which are actually observed, and investigations on the UAF specifications and preparation of the UAF-related standard evaluation systems for preparation of the draft standards for the Universal Accessible Filesystem (UAF), planned to be conducted in and after the next fiscal year, which allows, e.g., network seamless application of a variety of the future optical disks. (NEDO)

Evaluation report on research and development of a database system for mutual computer operation; Denshi keisanki sogo un'yo database system no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-01

This paper describes evaluation on the research and development of a database system for mutual computer operation, with respect to discrete database technology, multi-media technology, high reliability technology, and mutual operation network system technology. A large number of research results placing the views on the future were derived, such as the issues of discretion and utilization patterns of the discrete database, structuring of data for multi-media information, retrieval systems, flexible and high-level utilization of the network, and the issues in database protection. These achievements are publicly disclosed widely. The largest feature of this project is in aiming at forming a network system that can be operated mutually under multi-vender environment. Therefore, the researches and developments have been executed under the spirit of the principle of openness to public and international cooperation. These efforts are represented by organizing the rule establishment committee, execution of mutual interconnection experiment (including demonstration evaluation), and development of the mounting rules based on the ISO's 'open system interconnection (OSI)'. These results are compiled in the JIS as the basic reference model for the open system interconnection, whereas the targets shown in the basic plan have been achieved sufficiently. (NEDO)

Fiscal 1999 technical achievement report. Development project on international standards for developing new industry (Comprehensive research); 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Sogo chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Research and development of 13 individual subjects whose achievements are expected to come into use on the international scale was started in fiscal 1998, to be completed in three years. Progress is reviewed for each of the subjects, and the findings are mentioned below. Research and development is progressing smoothly, specifications to be internationalized have been narrowed down, and it is now foreseen that the main points of the specifications to be presented will be successfully prepared. There are some subjects, however, about which it is difficult to specify to which technical committees they are to be submitted. Assistance, for instance supply of information, by technical committees involved is indispensable. The attitude toward international standardization taken by European and American business corporations visited for study by Japanese researchers is to be disseminated to Japanese business corporations since the information thus collected will help them. Although 75% of the 13 subjects have reached a level where they may be presented as specifications for international standardization, yet they need active support by organizations concerned and research of trends of internationalization-related institutions before they are actually accepted as international standards. (NEDO)

Report on comprehensive surveys of nationwide geothermal resources in fiscal 1979. Conceptual design of a database system; 1979 nendo zenkoku chinetsu shigen sogo chosa hokokusho. Database system gainen sekkei

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-03-31

Conceptual design was made on a database system as part of the comprehensive surveys of nationwide geothermal resources. Underground hot water in depths of several kilometers close to the ground surface is a utilizable geothermal energy. Exploration using the ground surface survey is much less expensive than the test drilling survey, but has greater error in estimation because of being an indirect method. However, integrating data by freely using a number of exploration methods can improve the accuracy of estimation on the whole. In performing the conceptual design of a geothermal resource information system, the functions of this large scale database were used as the framework. Further data collection, distribution and interactive type man-machine communication, modeling, and environment surveillance functions were incorporated. Considerations were also given on further diversified utilization patterns and on support to users in remote areas and end users. What is important in designing the system is that constituting elements of hardware and software should function while being combined organically as one system, rather than the elements work independently. In addition, sufficient expandability and flexibility are indispensable. (NEDO)

Report on the FY 1999 international research cooperation project. Development of polymer materials from renewable resources using biocatalyst; 1999 nendo seitai shokubai wo riyoshita saisei kano shigen kara no kobunshi sozai no kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The R and D were conducted of saccharide polymer using biocatalyst and polylactic acid using biocatalyst. In the R and D of technology to synthesize polymerizing saccharide ester, the use of ALP901 led to success in acquiring hydrophobic polymerizing saccharide ester and saccharide ester with phenol residue. A study was also made of technology to synthesize polymerizing divinyl ester. In the study of the optimization of enzyme reaction conditions, the optimum temperature of ester exchange was 50 degrees C, and also under much higher temperature, 100 degrees C, the enzyme reaction was found to proceed with. In the study of the synthesis of polylactic acid, it was impossible to obtain polymer in the case of using ester lactate. However, in the case of using lactic acid, polymer was acquired at the numerical average molecular weight of approximately 1,200. In the study of the optimization of enzyme reaction conditions, polymer with high molecular weight was acquired at the enzyme amount of 5-10%. It was found out that the conversion rate exceeds 98% in the case of doing the reaction for more than 3 days at the enzyme amount of 5-10%. (NEDO)

Fiscal 1996 report on the results of the study under a consignment from NEDO of environmental friendly type metal base-materials recycling utilization basic technology and element/overall process. For public; 1996 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko kyodo kenkyu itaku. Kankyo chowagata kinzokukei sozai kaisei riyo kiban gijutsu no kenkyu: yoso sogo process kenkyu seika hokokusho (kokaiyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

A study of `the next generation new iron steel making process` was conducted in which impurity elements in scrap are removed and recycled into high quality steel making materials, and at the same time total emissions are reduced during the process from scrap melting to steel making. The paper reported the fiscal 1996 results. In the study of the scrap recycling process, conducted were a study of the total system to remove impurities in the high temperature preheating furnace, a large scale experiment of de-coaling combined type de-coppering/de-tinning under reduced pressure of iron melting, a study of recycling technology of dust to the scrap melting furnace, etc. In the study on preheating/melting technology, a study of the scrap melting furnace of high-productivity/low-energy vertical type, a study of the scrap preheating method using the packed bed type preheating furnace, a study on the flue gas control at the time of preheating/melting, a study of the fast assessment method for organic compounds in flue gas, etc. In the evaluation of the total system, a study of preheating/melting/environmental systems using experimental plants. 20 refs., 23 figs., 10 tabs.

Estimation of water-coal surface interaction during heat treatment of coal by use of FTir and DSC; FTir to DSC wo mochiita sekitan-mizu kan sogo sayo no teiryoteki hyoka

Energy Technology Data Exchange (ETDEWEB)

Miura, K.; Mae, K.; Morozumi, F.; Kusakawa, T. [Kyoto University, Kyoto (Japan)

1997-10-30

The authors have recently presented a method to estimate the strength distribution of hydrogen bondings in coal using FTir and DSC. The method was applied to estimate the strength of coal-water interaction in two different coals and to estimate the enthalpy change deriving from the change in hydrogen bondings during the desorption of water. The estimated enthalpy change was compared with the total enthalpy change estimated by DSC measurement to examine the importance of hydrogen bondings during the desertion of water. 1 ref., 6 figs.

FY 1998 international cooperation project for global environment/project to evaluate influence of climate change; 1998 nendo chosa hokokusho. Chikyu kankyo kokusai kyoryoku jigyo/kiko hendo eikyo hyokanado jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

As a part of the international cooperation for the global warming problem, evaluation/study were conducted on policy to lessen climate changes from viewpoints of scientific technology, environment, and economy/society. In the development of evaluation methods on cost analysis, the following were pointed out: Changes in resource utilization brought about as a result of the policy are all needed to be numerated; In resource, clean air and water, and also abolition of price barrier and prices now in force are included. As subjects on the technology transfer, cited are barriers in aspects of organization/system and barriers in aspects of economy/finance and society. Especially, it was pointed out that it is necessary to exchange the persons concerned in the industrial sector. Of various optional policies toward the prevention of global warming, the Kyoto mechanism not only has an economical merit of the use of low cost option but can be fairly promising from an environmental viewpoint of internationally controlling the greenhouse effect gas emission, if the characteristic of practically using the market can be so designed that it fulfills its function. (NEDO)

Influence of fragmentation of substrate on synergistic effect in hydrolysis of crystalline cellulose with cellulases; Seruraze niyoru kessho serurosu bunkaikatei deno sojokoka ni oyobosu kishitsu no danpenka no eikyo

Energy Technology Data Exchange (ETDEWEB)

Tanaka, M.; Morita, M.; Mitsui, R. [Okayama University of Science, Okayama (Japan). Dept. of Biochemistry

2000-05-10

The expression mechanism of synergistic effect is investigated by using two cellulase components obtained from Meicelase CEP-6000 by purification. Purified cellulose components are classified into two types. One, tentatively named CMCase-type (FIE and FIIIE), has relatively low values of the ratio of MCC hydrolysis to CMC hydrolysis, and considerably high values of the ratio of K{sub m} for MCC and CMC. The other, tentatively named MCCase-type (FIIE and FIVE), has largely different values about those properties. In the case of MCC hydrolysis with FIVE alone, the particle diameter of MCC decreases (fragmentation) and the particle number of MCC increased rapidly in the early stage of reaction, and both decrease gradually in the late stage of reaction. In the case of a mixture of the above two components is for an increase in amounts of reaction site in the substrate for FIIIE, dependent on fragmentation of MCC by FIVE, and the activity of FIVE is stimulated by FIIIE. In the case of the mixture of FIE and FIIIE, the synergistic effect is not expressed. This finding suggests that these two components do not have the activity of fragmentation of MCC. (author)

Effect of heat transfer in cylinder on air quantity of 4-stroke cycle gasoline engine; 4 Stroke gasoline engine no kyunyu shinkiryo ni oyobosu cylinder nai dennetsu no eikyo

Energy Technology Data Exchange (ETDEWEB)

Yoshida, M.; Oguri, Y.; Suzuki, T. [Sophia University, Tokyo (Japan). Faculty of Science and Technology

2000-01-25

Many papers concerning air quantity of 4-stroke cycle gasoline engine have been published. It has been reported in these papers that heat transfer in surface of cylinder and inlet port gives big influence to the air quantity. But it has not been clear which influence of heat transfer in cylinder and inlet port is strong. So the authors derived a function of the air quantity thermodynamically considering heat transfer, and examined which of influence of heat transfer was strong. The results show ; (1) The influence of heat transfer in cylinder is small (about 1%) at full load, and is also small (about 5%) at light load. (2) Heat transfer in cylinder almost increases the air quantity. (3) The influence of heat transfer in inlet port decreases the air quantity with around 30% greatly. (author)

Improvement of the material with the hard pressure for high fireplace. Koroyo koshitsu atsunyuzai no kaizen. (2) Ataunyuzai no bussei ni ataeru kotsuzai [center dot] ekitai bainda no eikyo

Energy Technology Data Exchange (ETDEWEB)

Tanaka, R. (Harima Ceramics Corp., Hyogo (Japan))

1999-02-01

It had already been reported, and the damage factor of the material with the pressure was investigated from the core boring sample with an opportunity this time, and improvement was done about the kind of the bone material, the liquid binder as for the material with the pressure of the phenol plastic base and that system. The reduction of the amount of binder became possible by using a thick bone material, and the ones for the volatilization decreased by adding the plastic of the high concentration again, and the appearance pore rates of the material with the pressure decreased and worked for high strength performance as a result. This high strength performance is thought to be effective against the decrease of the mechanical abrasion to the thing with high fireplace, which is the damage cause of the material with the pressure. (translated by NEDO)

Improvement of the material with the hard pressure for high fireplace; Koroyo koshitsu atsunyuzai no kaizen. (2) Ataunyuzai no bussei ni ataeru kotsuzai {center_dot} ekitai bainda no eikyo

Energy Technology Data Exchange (ETDEWEB)

Tanaka, R. [Harima Ceramics Corp., Hyogo (Japan)

1999-02-01

It had already been reported, and the damage factor of the material with the pressure was investigated from the core boring sample with an opportunity this time, and improvement was done about the kind of the bone material, the liquid binder as for the material with the pressure of the phenol plastic base and that system. The reduction of the amount of binder became possible by using a thick bone material, and the ones for the volatilization decreased by adding the plastic of the high concentration again, and the appearance pore rates of the material with the pressure decreased and worked for high strength performance as a result. This high strength performance is thought to be effective against the decrease of the mechanical abrasion to the thing with high fireplace, which is the damage cause of the material with the pressure. (translated by NEDO)

Fiscal 1997 report on the survey of effects of enhancement of energy consumption efficiency on the global environment; 1997 nendo chosa hokokusho (energy shohi koritsuka chikyu kankyo eikyo chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper surveyed the state of studying the measures against global warming in the third assessment report of the Intergovernmental Panel on Climate Change (IPCC) and made analyses of the trends of preventive measures for global warming in other countries, aiming at presenting data for studying the future enhancement of energy consumption efficiency in the Asia Pacific region. In the U.S., a report was taken up from Executive Office of the President which is entitled `the federal government R and D of energy for solution to problems in the 21st century.` The report made analyses of the federal government R and D of energy and at the same time recommended an increase in R and D budget and reinforcement of the organization of the Department of Energy. In Europe, the carbon tax, CO2 tax, energy tax, etc. are introduced or studied for reduction of CO2 emissions. OECD made public a report approved in May 1997 which is entitled `the environmental tax and green tax reform.` Also studied were the introduction and effects of the carbon tax aiming at reducing CO2 emissions in developing countries. More attention is being paid to economic effects predicted in case developed countries reinforce various kinds of measures for targeted reduction of greenhouse gases. 2 figs., 4 tabs.

Effects of short fiber reinforcement and mean stress on tensile fatigue strength characteristics of polyethersulfone; Tansen`i kyoka porieterusaruhon no hippari hiro tokusei ni oyobosu heikin oryoku no eikyo

Energy Technology Data Exchange (ETDEWEB)

Furue, H.; Nonaka, K. [Mechanical Engineering Lab., Tsukuba, Ibaraki (Japan)

1996-01-15

Thermoplastics are often reinforced with short fibers with aims of improvement of their strengths, rigidities and hardness or maintenance of their dimensional stabilities. Such short fiber reinforced plastic materials have more expectation for high performance plastics. Authors already examined of some effects of reinforced fiber and of orientation in injection molding on flexural fatigue characteristics of the injection-molded high performance thermoplastic materials. However, the examination of short fiber reinforced effects on fatigue strength characteristics was not always sufficient. In this study, in order to obtain a guiding principle for fatigue resistant design of the short fiber reinforced injection molding materials, polyethersulfones (PES) was examined on its tensile fatigue strength and an effect of short fiber reinforcement for improvement of its fundamental dynamic properties on its fatigue characteristics. Especially, its fatigue life characteristics was elucidated mainly on relationship of mean stress, stress amplitude and number of repeating fracture in tensile fatigue behavior. 10 refs., 15 figs., 2 tabs.

Effect of metal ion species on mechanical relaxation of ethylene-co-methacrylic acid based ionomers; Ethylene-metakuriru san ionomer no rikigaku kanwa ni oyobosu kinzoku ion shu no eikyo

Energy Technology Data Exchange (ETDEWEB)

Zeng, X; Araki, O; Takigawa, T; Masuda, T [Kyoto University, Kyoto (Japan); Takahashi, M [Kyoto Institute of Technology, Kyoto (Japan)

1996-12-15

Dynamic viscoelasticity of ethylene-co-methacrylic acid (EMAA) based ionomers containing Zn or Na as well as EMAA was investigated. The film samples used for viscoelasticity measurements were molded at 195{degree}C. Two kinds of specimens, quenched and slowly cooled samples after molding, were prepared for each polymer specimen. For the quenched samples, the effect of aging on dynamic viscoelasticity was also examined. The temperature dispersion curves of dynamic storage modulus (E{prime}) of the ionomers obtained by quenching showed a large decrease around 35{degree}C due to the glass transition of EMAA ionomers. The ionomers prepared by slow cooling showed a high value of E{prime} in the high temperature region, compared with the quenched samples. This may be due to the difference in the degree of ionic cluster formation in the ionomers. The values of E{prime} at low temperatures increased with aging time for the quenched samples, which originates from the equilibration of the glassy state by aging. 14 refs., 7 figs., 1 tab.

Study of dependence of DC output of rectenna array on the method of inter-connection of its array element; Rectenna array chokuryu shutsuryoku no array yoso sogo setsuzokuho izonsei no kenkyu

Energy Technology Data Exchange (ETDEWEB)

Shinohara, M.; Matsumoto, H. [Kyoto University, Kyoto (Japan). Radio Atmospheric Science Center

1997-08-20

In 1994 and 1995, a ground-to-ground microwave power transmission (MPT) experiment was carried out by a group of Kyoto University, Kobe University and Kansai Electric Power Company. Among the MPT technologies, which are one of the most important key issues for the realization of the Solar Power Satellite (SPS), studies of `rectenna` (rectifying antenna) have been pursued to archive higher efficiency of conversion from microwave to DC. We had developed a new rectenna panel which can effectively rectify a microwave power of 2.5 W at 2.45 GHz before the ground-to ground MPT field experiment. We examine the sum of the outputs of two or three rectenna panels in which are connected ether in parallel or in series or in the hybrid connection under the same microwave circumstances. The experiment leads us to conclude: (1) The sum of the DC outputs from two rectenna panels connected in parallel is larger than that from those connected in series. (2) The sum of the DC outputs of two rectenna panels is generally smaller than the sum of the DC output of the individual panels unless their output is equal to each other. (3) The total output DC power of a rectenna array increases when we connect the array element with consideration of the `element balance`. Based on the experiment, we propose an optimum method for connection of individual rectenna elements to form an rectenna array. 12 refs., 9 figs., 4 tabs.

Fiscal 1999 geothermal energy development promotion survey. Report on environmental impact survey - 5 (Musadake area); 1999 nendo chinetsu kaihatsu sokushin chosa. Kankyo eikyo chosa hokokusho (No.B-5 Musadake chiiki)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-01-01

For the purpose of clarifying the environmental impact to result from the digging of borehole N11-MD-3 in Shibetsu-gun, Hokkaido, a survey was conducted of changes in (1) hot spring water quality, (2) noise/vibration pollution, and (3) air pollution due to hydrogen sulfide, before and after the digging period. Under item (1), measurements were made at four hot springs, which involved weather, air temperature, water temperature, amount of welled-up water, pH, electric conductivity, etc. Although minor changes were observed during the measuring period, none was found related to the digging process. Under item (2), noise levels were measured during the drilling period along the site boundary, at a point 500m from N11-MD-3, the Kawakita hot spring, and the entrance of Sekiyunosawa. Along the site boundary, they were 55-60 dB during the drilling period, and there was an increase of 30dB attributable to the drilling. At the 500m point, there was a 15-20dB increase attributable to the same. Vibration levels during the drilling period were 40dB along the site boundary and less than the observable minimum at the other points. Under item (3), at four points along the site boundary (50m), hydrogen sulfide concentration in the air fluctuated by 0.01-0.21ppm when the steam discharge rate was 4.47-7.20t/h. (NEDO)

Study on initial stage of diesel spray formation. Effects of the condition inside the nozzle sac; Diesel funmu no shoki keisei katei ni kansuru kenkyu. Sac nai nenryo no eikyo

Energy Technology Data Exchange (ETDEWEB)

Ishikawa, N.; Tsujimura, K. [Nissan Diesel Motor Co. Ltd., Saitama (Japan); Komori, M.

1996-06-25

To realize clean diesel exhaust, it is very important to clarify the atomization phenomena of the fuel spray. In this study, the initial stage of the atomization process of a diesel injection fuel spray was analyzed with a high-speed image converter camera under the conditions of atmospheric gas pressure and room temperature. As a result, it was found that the initial spray formation was greatly affected lay the condition inside the nozzle sac. In the case in which fuel existed in the sac, pin-like structure spray formation was observed at the initial injection stage. This phenomenon was not observed in the case in which no fuel was present in the sac, and a widely spread fuel spray formation was observed at the initial injection stage. The relatively low-speed fuel spray injected in the initial low-sac-pressure condition was pushed away by the subsequent fuel spray injected in the high-sac-pressure condition. 7 refs., 12 figs., 1 tab.

Stability of diffusion flame formed in a laminar flat plate boundary layer. Effect of fuel dilution; Soryu heiban kyokai sonai ni keiseisareru kakusan kaen no anteisei. Nenryo kishaku no eikyo

Energy Technology Data Exchange (ETDEWEB)

Takeuchi, M [National Institute for Resources and Environment, Tsukuba (Japan); Ueda, T; Mizumoto, M [Keio University, Tokyo (Japan). Faculty of Science and Technology; Amari, T [Keio University, Tokyo (Japan)

1998-10-25

A stability limit of the diffusion flame with fuel injection from a porous wall in a laminar flat plate boundary layer is measured as functions of fuel (CH4) concentration of CH4/N2 injectant mixture ({chi}) and its injection velocity (v). The free stream velocity (U{infinity}) is set as 0.6 m/s. The thermal condition at the wall is controlled by setting temperature at the upstream end of the porous wall as a reference temperature. When v >20 mm/s, the flame becomes unstable with the separation of leading flame edge with decreasing {chi}. The value of {chi} at the stability limit is constant without regard to v as long as the wall temperature is kept constant. As the wall temperature is decreased the value of {chi} increases. The separation is supposed to take place as a result of the limit of the reaction rate. When v <20 mm/s, the flame becomes unstable with the oscillation. The value of {chi} at the stability limit increases drastically with decreasing v. The oscillation takes place mainly due to the repeat of the extinction due to heat loss to the wall and the flame propagation in the combustible layer. 10 refs., 8 figs., 1 tab.

Effect of insolation forecasting error on reduction of electricity charges for solar hot water system; Taiyonetsu kyuto system no denki ryokin sakugen koka ni oyobosu nissharyo yosoku gosa no eikyo

Energy Technology Data Exchange (ETDEWEB)

Nakagawa, S [Maizuru National College of Technology, Kyoto (Japan); Kenmoku, Y; Sakakibara, T [Toyohashi University of Technology, Aichi (Japan); Kawamoto, T [Shizuoka University, Shizuoka (Japan)

1996-10-27

A solar hot water system can be economically operated if inexpensive midnight power is purchased to cover the shortage of solar energy predicted for the following day. Investigations were conducted because error in insolation prediction affects the system operation and electric charge reduction effect. The target temperature of the heat accumulation tank at every predetermined time point is calculated on the previous evening in consideration of predicted insolation so that the water will be as hot as prescribed at the feeding time on the following day. Midnight power is used for uniform heating to attain the target temperature for 7 o`clock on the following morning. The uniform heating continues from 8 o`clock to the feeding time, this time using solar energy and daytime power to attain the target temperature. Accordingly, the division between the midnight power and daytime power is determined in view of the target temperature for 7 o`clock on the following morning, which target temperature is so set that the charge will be the minimum by optimizing the allocation of the above-said two. When the insolation prediction error rate is beyond 30%, the electric charge grows higher as the rate rises. But, when the rate is not higher than 30%, the charge is little affected by a rise in the rate. 5 refs., 10 figs., 1 tab.

Effect of sail on augmenting attitude stability of hovering VTOL vehicle supported by one-ducted-fan. Ductedter dot fan shiji VTOL ki no hover shisei anteisei eno ho no eikyo

Energy Technology Data Exchange (ETDEWEB)

Ando, S.; Kato, M. (Nagoya University, Nagoya (Japan). Faculty of Engineering)

1991-07-05

An analytical investigation was given on augmenting attitude stability of a VTOL airplane supported by one-ducted-fan, at hovering, by means of installing a sail having air resistance on a place higher than the vehicle center-of-gravity. Since the problem becomes nonlinear, the time-marching technique was used. The sail on which the emphasis was placed had an area of as less than several times as much of the duct sectional area, and a height of as less than several times as much of the duct diameter. The stabilization effect is expressed as {Delta}h = center of gravity height region providing the stability/duct diameter. Without a sail, {Delta}h was several percent, but with a sail, the value increased to about ten times as much. This increase in {Delta}h was remarkable in the direction that elevate the position of the center of gravity. More stability is obtained by increasing the sail height than by increasing the area. Substitutes to a sail, working on the same principle, could be a gas-bag and wind mill. A gas-bag, which can change its volume readily, will be able to vary the sail area easily. A wind mill could make the weight lighter than a sail, and has a possibility of varying the resistance through changing its blade pitch angle. 2 refs., 2 figs., 1 tab.

Fiscal 1997 report on the R and D project consignment from NEDO on industrial science and technology. R and D on total base technology for marine resources (Mn nodules mining system) (total system (experimental plan)); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kaiyo shigen sogo kiban gijutsu no kenkyu kaihatsu (mangan dankai saiko system) seika hokokusho (total system (jikken keikaku) hen)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Study was made on the design of experiments for confirming the technological and economical feasibility of commercial production of Mn nodules. An experimental sea area was selected considering Mn nodule characteristics such as concentration, continuity of nodule distribution and nodule size, and sea bottom topographic features such as flatness and exposed bed rock disturbing traveling of nodule collectors. The experimental plan was decided on the basis of the survey and study on an experimental scale, various requirements, weather and sea weather features of the sea area, and sea bottom conditions. Based on the experimental plan, various verification tests and simulation analyses were carried out, and functions of various equipment were confirmed. The conceptual design of a mining system assumed both pump-lift and air-lift systems, and yearly production rates of 2 and 3 million tons by 2 mining barges, and summarized main points of every system. As the evaluation result, the future direction of commercial production of Mn nodules was clarified to a certain extent. 5 figs., 21 tabs.

Overall analysis report on the fiscal 1994 geothermal development promotion survey. No.C-2. Wasabizawa area (secondary); 1994 nendo chinetsu kaihatsu sokushin chosa sogo kaiseki hokokusho. No.C-2. Wasabizawa chiiki (dainiji)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-01-01

The Wasabizawa area is located near the boundary between Yuzawa city south of Akita pref. and Ogachi-machi, Ogachi-gun, Akita pref, having a range of 3.0km northeast-southwest and 2.5km northwest-southeast of Wasabizawa almost as a center. The area for survey and its circumference are national forests, and the east and a part of the south of the area are designated as the Kurikoma quasi-national park third type special region. From the geochemical temperature distribution, it can be assumed that geothermal fluids of around 300{degree}C exist in the deep underground of the Kaminotai-Wasabizawa-Akinomiya area. From the distribution of density basements, the block structure of the basement can be estimated. Around the boundary of the ridge/sedimentation region of this density basement, fractures develop and the formation of reservoir structure is expected from the comparison with the result of the well survey. In the blowout test, obtained were 284.3{degree}C and 83.05 kgf/cm{sup 2} at a depth of 1,300m. In the geothermal system, it is assumed that reservoir structures of geothermal fluids develop in the deep underground of the central part of the area. The heat source to the geothermal system is supposed to be the magma reservoir remaining in Takamatsudake volcanic rocks. 110 refs., 177 figs., 105 tabs.

FY 1998 annual summary report on comprehensive development study of high-function flat panel display techniques (second year); 1998 nendo koseino flat panel display gijutsu no sogo kaihatsu kenkyu seika hokokusho. Daininendo

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This project is aimed at creation of the new world display industry in Shikoku by developing the high-function flat panel display techniques and thereby establishing new techniques which solve the problems involved in, e.g., LEDs, plasma-aided devices and ELs other than liquid crystal devices. For development of emitters using diamond, important results have been obtained for the morphology, and cathode luminescence, Raman and photoluminescence spectra of polycrystalline diamond, synthesized by the vapor-phase process under varying conditions, on the electron radiation characteristics of the emitters. These results have led to clarification of the optimum vapor-phase synthesis conditions for diamond for high-function emitters. The techniques utilizing focused ion beams have also advanced to develop thin polycrystalline diamond films for emitters which correspond to the image elements of quality for television. For electron emitters, a structure prepared by implantation without using a high electrical field is proposed, and the device mechanisms involved are clarified. (NEDO)

Report on fundamental investigation in fiscal 2000 of intellectual property right management criteria at General Research Institute of Industrial Technologies; 2000 nendo sangyo gijutsu sogo kenkyusho chiteki zaisanken kanri kiso chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Fundamental items of knowledge were collected on matters to form the base of management and utilization of intellectual property rights as the basic data for cooperation among industry, academia, and government. Activities were put into order on the following nine fields: 1) handling of tangible research property rights at universities, 2) the way the organization should be to support the cooperation between industry and academia - a mechanism at Massachusetts Institute of Technology (MIT), 3) licensing and technology transfer in India, 4) intellectual property trends for the 21st century, 5) management of intellectual property assets - in relation with the new current in the U.S. Patent Act, 6) comparative study of examination guidelines for computer-related inventions between the United States and Japan, 7) management of intellectual properties and business law aspects in the technology innovation times - examples in Seattle where IT and bio-technologies are originated from, 8) patents and bio-technical inventions, and 9) new movements in bio-technology patents. In Item 2), examples at MIT were studied on the way the organization should be to support the cooperation between industry and academia. The industry-academia cooperation is in action at various levels, not only in licensing, but also in the industrial liaison program, and consortiums. (NEDO)

Fiscal 1998 research report on the basic study on the effect of microgravity on living individuals; Bisho juryoku no seibutsu kotai ni taisuru eikyo no kiso kenkyu 1998 nendo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In order to clarify the effect of microgravity on vital functions and organisms at a cell level, this research studies the molecular biological response function of higher animals, the gravity acceptable mechanism of single-cell organisms, the effect of gravity on geotaxis of insects, measurement of monoamine system neurotransmitters of rat hippocampus by dialysis in a brain and the effect of microgravity on it, the effect of microgravity on water and bone metabolism functions and immunity function, and the analysis of BZ reaction as a simple model of vital reaction. The themes of the research are as follows: the effect of microgravity environment on cell fusion, the analysis of gravity acceptable mechanisms of single-cell organisms, the effect of oriental medical treatment on bone metabolism anomaly of mouses under microgravity environment, the effect of oriental medical treatment on change in physiological function under microgravity environment, the effect of microgravity environment on immunity systems, the effect of gravity on cell activities, the effect of a gravity field on chemical oscillation reaction, and the effect of gravity on geotaxis of insects. (NEDO)

Effect of coal rank and mineral matter on gasification reactivity of coal char treated at high temperature; Netsushorishita sekitan char no gas ka tokusei ni taisuru tanshu oyobi kobutsushitsu no eikyo

Energy Technology Data Exchange (ETDEWEB)

Morishita, K.; Takei, H.; Harano, A.; Takarada, T. [Gunma University, Gunma (Japan). Faculty of Engineering

1996-10-28

In the wide range from brown coal to anthracite, an investigation was made of effects of heat treatment on physical/chemical properties and of coal rank dependence. For the experiment, 12 kinds of coal samples were used, and for heat treatment, the fluidized bed heated by the electric furnace and the infrared-ray gold image furnace were used. To examine characteristics of the heat-treated coal char, conducted were oxygen gasification, TPD measurement, XRD measurement, alkali metal measurement, and pore distribution measurement. The following were obtained from the experiment. The gasification reaction rate of the char heat-treated in the temperature range between 900{degree}C to 1700{degree}C decreases with a rise of the temperature of heat treatment, and the degree of decrease in the rate depends on coal rank. The order of gasification rate between coal ranks depends on the temperature of heat treatment, and the lower the heat treatment temperature is, the more largely the gasification rate is influenced by catalysis of mineral matters included in the coal. As causes of the decrease in gasification rate associated with the rise in temperature of heat treatment, indicated were release of alkali metal having catalysis and decrease of active sites by carbonaceous crystallinity. 6 figs.

Reduction of artificial source effect in the high-resolution aeromagnetic survey in the Hanshin region; Hanshin chiiki no komitsudo kuchu jiki tansa ni okeru jinko noise source no eikyo no jokyo

Energy Technology Data Exchange (ETDEWEB)

Nakatsuka, T; Makino, M; Morijiri, R; Okuma, S [Geological Survey of Japan, Tsukuba (Japan)

1997-05-27

A high-resolution aeromagnetic survey was carried out in December 1995 on areas from Kobe City to Kyoto City in relation to the Hyogoken-nanbu Earthquake in 1995. It was found in the survey that effects of electric trains driven by direct current and man-made structures cannot be avoided, working as a large noise factor in extraction and analysis of geological information. This paper describes a quantitative analysis on magnetic anomaly suspected to have been caused from artificial sources seen in the magnetic map of the Hanshin area obtained from the above exploration data. The paper also gives considerations on methods to remove the effects therefrom. It then describes a quantitative analysis and the result of attempts on removal of the anomaly, taking up the following factors: (1) distribution of specific and remarkable magnetic anomalies which correspond to railroad positions of the Hanshin Railways running through the Nishinomiya-Toyonaka area, (2) the magnetic anomaly trend in positive and negative pair seen in the seafront area of Kobe City, and (3) typical bipolar isolated type magnetic anomaly in the north-west part of Kobe City. The cause for (1) was loop current flown for the railway operation, that for (2) was man-made structures in the improved seafront area, and that for (3) was a provisionally built metal waste storage yard. 9 figs.

FY 1998 result report. Research/development on the energy overall development/utilization technology of gas hydrate resource; 1998 nendo seika hokokusho. Gas haidoreto shigen no energy sogo kaihatsu riyo gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This study is aimed at studying for survey of gas hydrate (GH) deposit required for GH resource development and gathering of it, and further at studying for industrial utilization technology development of GH which is different in formation condition depending on kind of gas with which it reacts. The results of FY 1998 are as follows. In the study of the situation of existence of gas hydrate in the tundra, the sedimentary environment of the tundra where natural gas hydrate exists was simulated in laboratory to measure thermal conductivity of the sediments including GH. In this fiscal year, design/fabrication/calibration were conducted of the GH synthesizer and thermal analyzer. In the study of GH gathering technology in the tundra, a technology is discussed for recovering gas from GH layer and at the same time substituting CO2 hydrate for GH by blowing CO2 into the geologic layer. In FY 1998, formation/dissociation behaviors were first studied of methane/CO2 mixture hydrate. For the overall energy development of GH resource and promotion of R and D of the utilization technology, studies were made on physical properties of GH and development of the usage. (NEDO)

Fiscal 1993 survey of the base arrangement promotion for foreign coal import. Survey of the general situation of Thai coal; 1993 nendo kaigaitan yunyu kiban seibi sokushin chosa. Thai sekitan sogo jijo chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

The paper reported the energy situation in Thailand, the present and future status of coal supply/demand, the present situation of environmental policy and air pollution prevention policy and problems concerning coal and the measures for solution, and a possibility of Japan`s cooperation. In Thailand, the total coal supply amount in 1992 is 16.079 million tons, which is 9.1% of all the primary energy supply amount. The country produces only a few amount of anthracite and subbituminous coal beside brown coal. The domestic coal equals brown coal, the production of which was 15.335 million tons in 1992, 13.9% of all the primary energy demand. Concerning brown coal, 79.7% of all the brown coal supply are for electric power use, and others for industrial use such as the cement industry. The remaining reserve in developed areas is 151.4 billion tons, and the proven reserve in undeveloped areas 756 million tons. The demand for import coal was 11.25 million tons in 1996, and is expected to be 201.73 million tons in 2000. The paper pointed out some problems arising from coal production and spread of coal utilization, and described measures to solve the problems and fields where there are possibilities of Japan`s cooperation. 36 refs., 44 figs., 73 tabs.

Effect of Al content on critical CTOD properties in heat affected zone of C-Mn microalloyed steel. Teitanso teigokin koyosetsu netsu eikyobu no genkai CTOD tokusei ni oyobosu Al ganyuryo no eikyo

Energy Technology Data Exchange (ETDEWEB)

Fukada, Y.; Komizo, Y. (Sumitomo Metal Industries Ltd., Osaka (Japan))

1992-08-05

Two types of molten alloys specimen with a base of 0.10%C-0.20%Si-1.40%Mn-0.01%Ti system and varied Al content, were studied. The critical crack tip opening displacement(CTOD) properties in heat effected zone(HAZ) of extreme low Al content steel was stable at. extremely low temperature and there was no formation of M-A. Fine ferrite has a texture of [alpha] main body and it has been thought that the the change in the CTOD properties with the variation in Al content has been due to the difference in the texture. In case of Al content steel plate, the interfacial energy has been decreased due to excessive carbon concentration at [gamma] /[alpha] interface, M-A formation has been easier by the suppression of [alpha] transformation. In case of extremely low Al content steel plate, [alpha] transformation has been promoted and cementite deposition has been estimated from a small amount. of left [gamma] of extremely high carbon concentration. As for SH-CCT diagram of extremely low Al content steel plate, compare to Al content steel plate, [alpha] noze has shifted toward shorter time and formation of [alpha] has been easier within the normal welding cooling rate, and microstructures of [alpha] texture have formed in HAZ. 21 refs., 12 figs., 1 tab.

Influences of species of metals and supports on the hydrogenation activity of carbon-supported metal sulfides catalysts; Tanso biryushi tanji shokubai no suisoka kassei ni taisuru kassei kinzoku oyobi tantaishu no eikyo

Energy Technology Data Exchange (ETDEWEB)

Sakanishi, K.; Hasuo, H.; Taniguchi, H.; Nagamatsu, T.; Mochida, I. [Kyushu University, Fukuoka (Japan). Institute of Advanced Material Study

1996-10-28

In order to design catalysts suitable for primary liquefaction stage and secondary upgrading stage respectively in the multi-stage liquefaction process, various carbon-supported catalysts were prepared. Catalytic activities of them were investigated for the hydrogenation of 1-methylnaphthalene, to discuss the influences of metals and carbon species on the catalytic activity. Various water soluble and oil soluble Mo and Ni salts were used for NiMo supported catalysts. Among various carbon supports, Ketjen Black (KB) was effective for preparing the catalyst showing the most excellent hydrogenation activity. The KB and Black Pearl 2000 (BP2000) showing high hydrogenation activity were fine particles having high specific surface area more than 1000 m{sup 2}/g and primary particle diameter around 30 nm. This was inferred to contribute to the high dispersion support of active metals. Since such fine particles of carbon exhibited hydrophobic surface, they were suitable for preparing catalysts from the methanol-soluble metals. Although Ni and Mo added iron-based catalysts provided lower aromatic hydrogenation activity, they exhibited liquefaction activity competing with the NiMo/KB catalyst. 3 refs., 1 fig., 3 tabs.

Fiscal 1999 survey report. Survey of environmental effect pertaining to survey for geothermal development and promotion (Hakusuigoe area); 1999 nendo chinetsu kaihatsu sokushin chosa no uchi kankyo eikyo chosa (Hakusuigoe chiiki) hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This survey of environmental effect was intended to grasp actual state concerning some environmental factors that should agree with survey/development and also to assess its effect on the surrounding environment, particularly as a part of the 'stage C' in the 'survey for geothermal development and promotion', which was implemented by the Government for the purpose of guiding geothermal development by enterprises. This report compiles the plan details of the environmental effect survey to be conducted in the Hakusuigoe district, and presents proposals. The survey area is in the north of Makizono-cho, Aira-gun, in Kagoshima prefecture and situated about 3 km west of Onaminoike in Karakunidake, one of the peaks in the Kirishima mountain range. The Ogiri geothermal power plant is in the west of the site, a tourist spot Ebino Heights about 4 km northeast, and the Kirishima hot-spring about 4 km southeast. The location is in the national park, with a part designated as No. 2 and 3 class special areas. The environmental effect survey was divided broadly into such categories as fauna/flora, hot-spring water alteration and inland water, landscape, noise/vibration/subsoil, and air/water, and was further subdivided in accordance with the actual operations. (NEDO)

Study on the performances of handling and stability influenced by the differential terms in the state variables; Soansei ni okeru jotai hensunai no bibun yoso ga seino ni oyobosu eikyo no kento

Energy Technology Data Exchange (ETDEWEB)

Sugasawa, F [Tamagawa University, Tokyo (Japan); Mori, H [Nissan Motor Co. Ltd., Tokyo (Japan)

1997-10-01

The analysis method using the system matrix for state variables can not be applied to the analysis for the system has Complex Cornering Stiffness. The reason is there are differential terms in the state variables. It is found that the differential terms m the state variables can be changed to the constant terms in another state variables. 4 refs., 9 figs.

Influence on driver fatigue of vertical vibrations over long distances. Assessment in terms of stress hormones; Driver no unten hiro ni okeru joge shindo no eikyo. Stress hormone wo shiyo to shite

Energy Technology Data Exchange (ETDEWEB)

Taguchi, T.; Inagaki, H. [Toyota Central Research and Development Labs., Inc., Aichi (Japan)

1998-05-01

Driving tests are conducted to obtain some indexes that describe the cumulative effect of the sense of tiredness. The heart rate, Mayer wave related sinus arrhythmia, respiratory sinus arrhythmia, urinary adrenaline, noradrenaline, and cortisol in saliva are tested. Adrenaline and Mayer wave related sinus arrhythmia are ultimately named in view of their correlation with tiredness. It is believed that tiredness is attributable to two factors, which are increase in mental stress and decrease in vigilance. An excitation test is then conducted using a motion simulator. Upon application of 4Hz vibrations (equivalent to the chest section resonance frequency), adrenaline increases sharply, and then decreases sharply upon termination of excitation. Upon application of 1.6Hz vibrations (equivalent to the head section resonance frequency), adrenaline increases but not sharply, and the elevated level is sustained for some time after excitation. Driving tests are next conducted using a vehicle with its suspension fixed and another with 1-2Hz vibrations reduced. Rise in the adrenaline level is found inhibited aboard the latter. No difference is detected in terms of Mayer wave related sinus arrhythmia between the two vehicles. 4 refs., 7 figs., 4 tabs.

Fiscal 1998 survey for geothermal energy development promotion. Environmental impact survey report (No. B-7 Kuwanosawa region); 1998 nendo chinetsu kaihatsu sokushin chosa. Kankyo eikyo chosa hokokusho (No.B-7 Kuwanosawa chiiki)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

This survey aims to learn the current states of environmental factors required for the comprehension of the impacts on surroundings of a structural boring for geothermal energy exploration. The target site is an approximately 10km{sup 2}-large area located among the mountains 20km south-south-east of Yuzawa City, Akita Prefecture. It is found that numerous animals and vegetables inhabit the Kuwanosawa region and its vicinity. They are 19 species of mammals in 10 families under 5 orders; 73 species of birds in 25 families under 10 orders; 6 species of reptiles in 13 families; 9 species of amphibians in 6 families under 2 orders; and 719 species of insects in 179 families under 17 orders. Valuable animals include flying squirrels, mandarin ducks, black salamanders, and small Gifu butterflies. There are 670 species of vegetables in 132 families. Valuable vegetables are Iinuma bulblets, wild rhubarb roots, and Amur adonises. Floras found in existence are a natural flora in the beech class area, compensatory flora in the beech class area, afforested area, and a flora in the crop land. No remarkable fluctuation was observed in the Takamatsu spa throughout the survey period. Fluctuations were observed in all the survey items at the Doroyu-Okuyama inn. (NEDO)

Comprehensive research concerning the development of effective utilizing techniques of biological resources (large scale research out of the framework). Seibutsu shigen no koritsuteki riyo gijutsu no kaihatsu ni kansuru sogo kenkyu (ogata betsuwaku kenkyu)

Energy Technology Data Exchange (ETDEWEB)

1991-10-25

This paper is a research report in which the cultivated production of forest resources, the development to useful substances and the systematization to take the root in a region were studied. The distribution maps of biological resources on respective woodland systems: that is, the nationwide distribution maps of the amount of resources in Japan as to the broadleaf trees in private forests and national forests, the available amount and kinds of tree were prepared. As for the establishment of cultivation technique of the super-short deforestation forest, that is, pursue of wooden growth to the maximum limit, the superior clone 26 system was selected from the willow group through the research of wooden cultivation and the clone which showed the maximum yield reached 24t/ha every year. As for the material preparation technique due to microbial enzymes, that is, the creation and breeding of fungi which have the high lignin decomposition power, a stock of fungi which has the high lignin decomposition power and the decomposition selectivity was created by the cell fusion and the UV (ultraviolet ray) radiation treatment. As for the use of effective components in wooden resources, many useful characteristics could be detected by applying the boiling, bursting and ozone treatment. As for the mushroom cultivation through the application of unused tree kinds, a new kind of mushroom for food service was selected to clarify the possibility of fruit body formation. The development of a new material from conifers is promising. 1 tab.

FY 2000 Research and development of technology for medical and welfare equipment. Report on the comprehensive survey on welfare equipment; 2000 nendo iryo fukushi kiki gijutsu kenkyu kaihatsu chosa hokokusho. Fukushi kiki sogo chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The survey is conducted on the advanced basic and application technologies for medical and welfare equipment, e.g., biotechnology and drug delivery systems, to promote development of these technologies. For development of the gene-aided diagnostic system equipment for clinical purposes, surveys are conducted on current medical equipment and related technologies, and the results are summarized and pigeonholed for each equipment type. Also summarized are the small- to medium-sized enterprises which are considered to have techniques needed for development of sensors for heart disease treatment systems. For usability of welfare-related equipment products, investigations are made viewed from the designs oriented to human adaptability, human adaptable designs in the aging societies, and welfare-related problems in the aging societies and usability. The latest information on leading organizations and researchers is collected, for continuation and development of the usability programs for welfare-related equipment products, and also for inviting the current related technologies and researchers on life supporting for the aged in Japan to the programs. (NEDO)

Overview of FY1997 human media technology R and D; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu seido Shin energy Sangyo Gijutsu sogo Kaihatsu Kiko itaku jigyo. Human media no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper reports a summary of results in fiscal 1997 of research and development of human media technology. Fiscal 1997 launched design and trial fabrication of the following items: interface to improve efficiency and safety of plant operators, accommodation of multimedia contents to aid Kansei design, city development design aiding technologies using contents retrieval and presentation technologies and virtual reality, and empirical evaluation technologies for safety, comfort and convenience. Specific study assignments were extracted on a virtual media technology, a Kansei media technology and a knowledge media technology being three elementary technologies for human media to make clear the research and development approaches to be taken in the coming fiscal years. In addition, a human media technology committee, a research and development working group, and an investigation working group were established. Also launched were investigations on research trends in the human media technology, and investigative researches on contacts of information needs in industries with human media. 59 refs., 114 figs., 24 tabs.

Few studies of the effect of diluents on extraction of cobalt with D2EHPA. D2EHPA ni yoru Co no chushutsu ni ataeru kishakuzai no eikyo ni kansuru jakkan no kento

Energy Technology Data Exchange (ETDEWEB)

Aranae, M.; Nakataka, Y.; Wakamatsu, T. (Kyoto Univ., Kyoto (Japan). Faculty of Engineering); Saito, I.; Sakamoto, H. (Environment Research Inst. Resources Technical Tsukuba (Japan))

1991-12-27

Study was made on extraction of cobalt from weak acid solution with di-(2-ethylhexyl) phosphoric acid (D2EHPA) using various polar diluents such as benzene, toluene, o-xylene, m-xylene, n-heptane, cyclohexane and n-hepatne-benzene mixtures. Extraction efficiency of cobalt has decreased in the order, n-heptane > cyclohexane > m-xylene > o-xylene > toluene > benzene and this order has been in good agreement with the decreasing order of solubility parameters of diluents,and has shown the possibility of application of regular solution theory. When n-heptane and cyclohexane as diluents, in low loading ratio(L),were used Co-D2EHPA polymer were formed compared to other diluents. On the other hand when mixture of n-heptane/benzene was used as diluent, the efficiency of extraction, salting-out effect and formation of Co-D2EHPA polymer has changed with the texture of mixture.This change may be due to the effect of L and it has been thought for the necessity of investigation of extraction of cobalt in low polar diluents. 13 refs., 5 figs., 2 tabs.

FY 1998 geothermal development promotion survey. Report on the environmental effect survey (No. A-4 Kunbetsu-dake area); 1998 nendo chinetsu kaihatsu sokushin chosa. Kankyo eikyo chosa hokokusho (No.A-4 Kunbetsudake chiiki)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-30

Of the FY 1998 geothermal development promotion survey, the primary environmental effect survey in the Kunbetsu-dake area was conducted, and the results were arranged. In the well drilling survey, etc., the survey was made aiming at extracting areas to be preserved from an environmental aspect. The results of the survey were summarized as follows: As to the mammalia, 12 families 46 species were confirmed in the area surveyed and the periphery by literature survey. Out of them, the noticeable species which are considered important from an academic viewpoint are 10 families 19 species. As to the aves, 55 families 340 species were confirmed, of which 29 families 79 species are noticeable species. About the amphibia/reptilia, 3 families 3 species in the amphibia and 4 families 6 species in the reptilia were confirmed by literature and hearing survey. The noticeable species is 1 family 1 species in the amphilia. Concerning the terrestrial insecta, 135 families 873 species were confirmed, and the noticeable species is 11 families 20 species. As to the flora, 115 families 1055 species were confirmed, and the noticeable species is 46 families 126 species. Relating to the living vegetation, the one higher than 9 in nature reserves shows a substantial rate, and the periphery of Kaibetsu-dake is designated as the specified flora colony. (NEDO)

Effects of sand compaction pile (SCP) driving on the strength of clay outside the improved area; Sand compaction pile no dasetsu ga jiban kairyo ikigai no nendo jiban no kyodo ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Matsuda, H. [Yamaguchi University, Yamaguchi (Japan); Takahashi, S. [Ministry of Transport, Tokyo (Japan); Fujiwara, K. [Penta-Ocean Construction Co. Ltd., Tokyo (Japan); Kitayama, N. [Fukken Co. Ltd., Hiroshima (Japan)

1998-06-21

This paper describes effects of the disturbance by the sand compaction pile (SCP) driving operations on the shear strength of clay outside the improved area and the border of region affected by the SCP driving. About 1,400 soil specimens were taken before and after the SCP driving inside and outside the improved area during the foundation improvement at Tokuyama-Shimomatsu Port in Yamaguchi Prefecture. Soil test data of the specimens and strength characteristics of disturbed clay specimens were investigated through the laboratory experiments. The results obtained are as follows. According to the multi-directional simple shear test results, the shear strength immediately after the cyclic shear decreased in 10 to 30% compared with that before the cyclic shear. When recompaction was conducted before the cyclic shear, however, it increased in 50% compared with that before the cyclic shear. The strength of clay decreased by the SCP driving even outside the improved area. When the internal frictional angle of clay, friction coefficient of the improved boundary and driving depth of SCP were determined, it was possible to estimate an area affected by the SCP driving using a combined sliding plane. 21 refs., 18 figs.

Effect of aluminum on the growth and nutrient uptake in cryptomeria japonica D.Don and Chamaecyparis obtusa Sieb. et Zucc.; Sugi oyobi hinoki no ikusei to yobun kyushu ni oyobosu aluminium no eikyo

Energy Technology Data Exchange (ETDEWEB)

Kono, Y; Matsumura, H; Kobayashi, T [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1995-09-10

Two-year-old seedlings of Sugi (Japanese cedar: Cryptomeria japonica D. Don) and Hinoki (Japanese cypress: Chamaecyparis obtusa Sieb. et Zucc.) were grown for 4 months in 1/5 Hoagland`s No.2 nutrient culture solution containing aluminum chloride in the concentration range of 0.5 to 20 mM within the pH range of 3.5 to 4.0. Aluminium supplied at or below 1 mM of Al had no effect on the mortality of these species. However, the increase Al concentration higher than 2 mM increased the mortality. While they showed significant growth reduction at or higher Al concentration of 5 mM, there were no difference in growth response to Al between the two species in this experiment. While Al contents in leaf and root significantly increased with increasing Al concentration in the solution, contents of Ca, Mg and P in leaf decreased. Roof p content in Sugi increased with the increase of Al concentration in the solution, while no such change was observed in Hinoki root. This result suggests that Al might make phosphate immobile or inviolable form in Sugi root and this might lead to the reduced translocation of P into the leaf. In contrast, Al did not interfere with the uptake of phosphate in the root, however, it might interrupt phosphate transport into leaf from root system in Hinoki. The Al concentration such as 5 mM in the root sphere induced growth reductions in Sugi and Hinoki, with no significant difference in the response between the two species. This concentration was much higher than those reported in the field crops, vegetables and/or herbs. Thus, if soil acidification will be induced by acidic deposition in future, these herbaceous plants will be influenced faster than the conifer trees. This also means that ground vegetation change will be observed earlier than the conifer decline by the soil acidification stress. 23 refs., 5 figs., 3 tabs.

Fiscal 1999 geothermal energy development promotion survey. Report on survey of introduction of techniques for predicting impact on hot springs; 1999 nendo chinetsu kaihatsu sokushin chosa hokokusho. Onsen eikyo yosoku shuho donyu chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-08-01

In an effort to find guidelines on how to proceed with geothermal energy development so that it may coexist with hot springs, investigations are conducted into cases of impacts on hot springs imposed by geothermal energy development activities. An impact is judged to exist when geothermal development results in a decrease or depletion of pumped or spontaneously welling hot spring water, change in the concentration of dissolved chemical ingredients, fall in water temperature, or in an increase in the amount of discharged steam. Keyword-aided retrieval of data from databases is performed, and geothermal magazines are referred to for information. There are articles reporting impacts imposed by geothermal development on hot springs in the Palinpinon area (Philippines) and 12 others and in the Corwin Springs area (U.S.) and 13 others. These articles carrying outlines and impacts of geothermal development are collected, put in order, and analyzed. Cases in which such impacts are found to exist are categorized into four groups and, in each group, episodes are differentiated from each other by the type of mechanism linking the aquifer and the reservoir which is the object of development. (NEDO)

Study on turning performance of four-track steering vehicles. Effect of traction force and track speed distribution control; Sodashiki sokisha no senkai seino ni kansuru kenkyu. Kudoryoku haibun to sokudo haibun no eikyo

Energy Technology Data Exchange (ETDEWEB)

Imamura, M; Watanabe, K; Kitano, M [National Defense Academy, Kanagawa (Japan)

1997-10-01

The four-track steering vehicles (4TS) is a new type of off-road vehicle which can replace four wheels with track units to improve the mobility on soft terrains. In this paper, the numerical simulations, under the various types of differential and track velocity control systems, are conducted to predict the turning performance and steer ability of the 4TS vehicles. The results of the numerical analysis demonstrate that the differential systems with realistic combined distribution control systems of the track speed is efficient at a small turning radius. 4 refs., 13 figs.

Effects of types of work and visual environemnt on human pschology and behavior in an office space. Shikankyo ga shitsumusha no shinriter dot kodo ni oyobosu eikyo sagyo naiyo no chigai ni yoruhyoka

Energy Technology Data Exchange (ETDEWEB)

Sato, M [The Tokyo Electric Power Co. Inc., Tokyo (Japan); Inui, M., Nakamura, Y. (Tokyo Institute of technology, Tokyo (Japan))

1991-10-30

In this paper, was investigared an effect of work and visual environment types on the psychology and behavior of workers in office spaces in terms of subjective appraisal, work performance, behavior pattern, etc. In order to make a such effect of visual environment clear, a series of factorial experiments were conducted. Window and interior decoration of pot plants and paintings were adopted as factors of the visual environment. A Krepelin addition, a Krepelin addition-subtraction and multiplication, a Krepelin machiene, a hand-written manoscript, a word-processed manuscript, and a mirror tracing were adopted as work types. The number of sobjects was five for each work type. Consequently, a significance of the effect of the window and interior decoration on workers was verified. It was also found that the presence of the window and interior decoration improved the work performance for the major types of perfomance test. Furthermore, it was revealed that the presence of the window ans interior decoration the behavior of subjects active. 11 refs., 11 figs., 9 tabs.

Fiscal 1996 survey report. `Ultra high electronic technology development promotion project` under consignment from NEDO; 1996 nendo kenkyu seika hokokusho. Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku jigyo `chosentan denshi gijutsu kaihatsu sokushin jigyo`

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-05-01

For the purpose of establishing ultra high technology of a next next generation level which is a basic technology in the electronic information field, a key to the realization of the high grade information society and a common technology base giving marked influences to the wide range industrial field, the R and D was started of ultra fine processing process technology, technologies on limit measuring/analysis/control and new functional electronic materials. Themes of the R and D are electronic beam direct picture drawing system technology, ultra short wavelength electromagnetic radiation patterning/system technology, ultra fine sensitizing technology to draw pictures on metal and crystal surfaces using ultra short wavelength laser beams, shading system technology of shading mask to be used to the process of drawing ultra high accuracy and complicated figures, ultra high tech plasma reactive measuring/analysis/control technologies which become the base of ultra thin films and ultra fine etching using plasma, ultra high tech cleaning base technology, ultra high sensitivity medium technology, new functional element/film formation technology, etc. 137 refs., 358 figs., 38 tabs.

FY 1999 Report on the technical results. Research and development project for creation of the quick-effect type international standards (Comprehensive surveys); 1999 nendo sokkogata kokusai hyojun sosei kenkyu kaihatsu jigyo seika hokokusho. Sogo chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Safety, environment protection and internationality are most important product qualities, and international standardization of product qualities and testing methods are essential for strengthening international competitiveness. Viewed from this angle, the R and D project is conducted to propose the international standards for the following 5 areas related to environment and safety, selected in expectation that the results could be obtained in short time for preparation of the international proposals; (1) standardization of the wireless IC tags for logistics management, (2) standardization of quality and testing methods of automobile fuels and lubricants, (3) research and development for international standards in the field of safety of machinery, (4) standardization of evaluation methods for electronic data security system, and (5) standardization for the safety of light emitting diodes. The results are obtained for preparation of the international standard drafts, interim or final. The activities are directed to promotion of international interchangeability of radio frequency identification (RFID) systems for area (1); to standardization of the systems for emergency stopping/controlling machines for the area (3), to improvement of security evaluation standards of existing information systems for the area (4), and to unification of the ISO/IEC safety standards for the area (5). (NEDO)

Fiscal 1993-1998 integrated research report. R and D on advanced combustion technology under microgravity environment; 1993 - 1998 nendo sogo seika hokokusho. Bisho juryoku kankyo wo riyoshita kodo nensho gijutsu soshutsu ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For developing advanced combustion technology by using JAMIC's facility, the advanced combustion technology research committee supported by researchers of universities, national institutes and industries was prepared in JSUP, and R and D using a microgravity experiment facility and the international joint research with NASA were carried out. By using the advanced experimental equipment and measuring instrument developed for microgravity experiments, studies were made on combustion and evaporation of fuel droplets, combustion characteristics of dense fuel, flammability limit and NO{sub x} generation mechanism, and such precious results were obtained as storage of abundant experimental data, explication of a combustion mechanism, preparation of a database and find of new phenomena. In the ground verification experiment using the newly fabricated advanced combustor test equipment, various data effective for developing high-efficiency low-pollution combustors were obtained. Through the joint research with NASA including 5 themes, various results and the real relationship between the researchers were also obtained. (NEDO)

Fiscal 1997 survey report. `Ultra high electronic technology development promotion project` under consignment from NEDO; 1997 nendo kenkyu seika hokokusho. Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku jigyo `Chosentan denshi gijutsu kaihatsu sokushin jigyo`

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-05-01

For the purpose of establishing ultra high technology of a next next generation level, the R and D was conducted of ultra fine processing process technology, technologies on limit measuring/analysis/control and new functional electronic materials. Themes of the R and D are electronic beam direct picture drawing system technology, ultra short wavelength electromagnetic radiation patterning/system technology, ultra fine sensitizing technology, ultra high accuracy shading system technology, ultra high tech plasma reactive measuring/analysis/control technology, ultra high tech cleaning basic technology, ultra high sensitivity medium technology, new functional element/film formation technology, etc. This R and D is a greatly influential basic research in the whole industrial field, and therefore, it is necessary that researchers standing foremost in each field of industry/university/government join the project and that various R and D infrastructures are made the most of. For this, the concentrated joint research method and the dispersed joint research method are combined, and the R and D is being conduced by equal partnership of each researcher. 421 refs., 823 figs., 91 tabs.

Biochemical and toxicological impacts of persistent organochlorines on aquatic ecosystem. With particular attention to dioxins and their related compounds; Zanryusei yuki enso kagobutsu no suiken seitaikei eno eikyo. Toku ni dioxin rui ni chakumokushite

Energy Technology Data Exchange (ETDEWEB)

Iwata, H. [Hokkaido University, Sapporo (Japan)

1998-07-10

PCDDs, PCDFs and coplanar PCBs are organochlorine compounds which induce toxicological impacts on test animals, such as reduced weight, thymic gland dwarf, hepatotoxicity, immunotoxicity, developmental toxicity, carcinogenecity, teratogenicity and endocrine disturbance. They are generally referred to as dioxins. They are difficult to be decomposed in vivo, and tend to be more concentrated in higher organisms, placed at higher positions in the food chain. In aquatic ecosystems, they are observed to accumulate at high concentrations in fishes, fish-eating birds, claspers and whales. Therefore, there are growing concerns over their possible adverse effects on wild animals in aquatic ecosystems. This paper describes the effects of persistent organochlorine compounds on fishes, birds and aquatic mammals; and induction of cytochrome P450 of each organic species, caused by exposure to dioxins, and the induction examples in aquatic ecosystems. It also discusses whether or not the cytochrome P450 induction capacity of each organism species can be used as an index which explains difference between organism species in toxicological impacts of dioxins. 33 refs., 1 fig., 1 tab.

Fiscal 1999 survey report. Project of promoting international cooperation on global environments/Project of assessing climate change impacts; 1999 nendo chikyu kankyo kokusai kyoryoku suishin jigyo chosa hokokusho. Kiko hendo eikyo hyoka nado jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

As part of international cooperation concerning global warming, an assessment is conducted of climate change mitigating measures, from the viewpoints of technology, environment, economy, and community, in coordination with the IPCC (Intergovernmental Panel on Climate Change) 3rd working group responsible for energy policy and technological development. It aims to contribute to the preparation of a 3rd assessment report, and covers (1) the development of an assessment technique relating to cost analysis, (2) problems in the transfer of technology and solutions for them, and (3) the assessment of various policy options. Under item (1), studies are made about modelling techniques, common parameters and their values, potentials for effect, control of warming, etc. Under item (2), factors impeding the transfer and diffusion of technology are extracted and solutions therefor and the establishment of new incentives are deliberated, with analysis and investigation focused on tasks and solutions for furthering global transfer of technology with attention paid to various specific cases. Under item (3), concrete and feasible policy options are discussed on the basis of the outcome of the above-named endeavors, in view of characteristics of each of the regions, departments, and techniques. (NEDO)

Effect of pore water pressure on P-wave velocity in water-filled sands with partial air saturation; Fukanzen howa jotai no suna shiryo wo denpasuru P ha sokudo ni oyobosu kangeki suiatsu no eikyo

Energy Technology Data Exchange (ETDEWEB)

Kanema, T [Chishitsu-Keisoku Co. Ltd., Tokyo (Japan)

1997-10-22

With an objective to elucidate change in velocity of elastic waves in association with water pressure increase in a sand bed below the groundwater level in a shallow portion of the ground, a measurement experiment was carried out on P-wave velocity in sand samples with partial air saturation. The experiment has used fine sand having an equivalent coefficient of 2.40, a soil particle density of 2.68 g/cm {sup 3} or 60%, and a grain size of 0.36 mm. Inside the water-filled sand sample, two accelerometers were embedded 20 cm apart from each other as vibration receivers. An electromagnetic hammer for P-wave was used as the vibration source. In the experiment, measurement was carried out on the P-wave velocity in association with increase in pore water pressure by applying water pressure afresh to the water-filled sample. As a result of the experiment, the following matters were disclosed: the P-wave velocity increases as the pore water pressure was increased, and a phenomenon was recognized that the dominant frequency changes into high frequency; the degree of increase in the P-wave velocity varies depending on initial saturation of the sample; and bubbles in the pore fluid have their volume decreased due to compression resulted from increased pore water pressure and dissolution of air into the pore water. 6 refs., 11 figs.

Surface flaw detection by means of infrared radiometer. Part 3. ; Detection limit influenced by an environment temperature. Sekigai hoshakei ni yoru hyomen kekkan no kenshutsu. 3. ; Shuhen ondo ni yoru kenshutsu genkai no eikyo

Energy Technology Data Exchange (ETDEWEB)

Okamoto, U; Kaminaga, F [Ibaraki University, Ibaraki (Japan). Faculty of Engineering; Ishii, T [Ibaraki University, Ibaraki (Japan); Eto, M; Ooka, N; Kanaya, K; Eto, Y [Japan Atomic Energy Research Institute, Ibaraki (Japan); Kurokawa, T [Nippon Denki Sanei Ltd. Co., Tokyo (Japan)

1990-12-20

Measuring a radiation energy distribution around surface flaw by means of a infrared rediometer can detect fine flaw on the surface. The characteristics were examined using a light quantum type radiation thermometer consisted of Hg-Cd-Te as a sensor. A surrounding wall consisted of a black body wall was installed between the sensor and test piece, and by thus maintaining the surrounding wall temperature constant, reflection energy from the test piece surface was maintained constant for stabilized measurement. The measurement values are the sum of energies from emission and reflection, or the so-called radiosity values. To avoid effects from the reflection to reduce variance in the emissivity, it is necessary to keep the surrounding wall temperatures lower by more than 20 {degree}C than the test piece radiation temperatures. Emissivity can be calculated from the rediositivity (sum of the radiation and the reflection), the surrounding wall temperatures, and the test piece radiation temperatures. If the surface is rough, variance in the measurements increases. The larger the difference in the test piece and surrounding wall temperatures, the thermo image of the defects on the test piece surface becomes more distinctive, thus the detection limit can be enhanced. 7 refs., 13 figs.

Effects on annual cost of solar/air-heat utilization system of carbon tax and interest rate for a residential house; Jutakuyo taiyo/taikinetsu riyo system no nenkan keihi ni oyobosu tansozei kinri no eikyo

Energy Technology Data Exchange (ETDEWEB)

Shen, Q; Kenmoku, Y; Sakakibara, T [Toyohashi University of Technology, Aichi (Japan); Nakagawa, S [Maizuru National College of Technology, Kyoto (Japan); Kawamoto, T [Shizuoka University, Shizuoka (Japan). Faculty of Engineering

1996-10-27

In recent years, a system has been proposed that utilizes river heat, air-heat, exhaust heat from a cooler, etc., in addition to natural energy for the heat pump. With the introduction of such system, the amount of energy used and that of CO2 exhaust will be greatly reduced, but annual expenses will be increased as it stands. In order to improve the cost efficiency of the system, a proposal has been made for the introduction of an economic policy such as the carbon tax and a low interest financing system. With these matters in the background, the subject study predicts the production of solar cells in the future and, on the basis of this production, determines the price, conversion efficiency and equipment energy of solar cells in the future. Using these values and taking into consideration the introduction of the carbon tax and the low interest financing system, the optimum area was determined for solar cells and heat concentrators in a future residential solar/air-heat energy system. The carbon tax, being imposed on all CO2 discharges, had a large effect. Moreover, as the tax increased, annual expenses decreased for the solar/air-heat system. 3 refs., 6 figs.

Fiscal 1998 research report on promotion of geothermal development. Environment impact research report (No. A-4 Kunbetsu-Dake area); 1998 nendo chinetsu kaihatsu sokushin chosa. Kankyo eikyo chosa hokokusho (No.A-4 Kunbetsu chiiki)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-06-01

For extracting the areas to be conserved from the viewpoint of environment for the research on geothermal well drilling, the environment impact research was made on the protection and regulation states of animals and plants in Kunbetsu-Dake area. 46 species in 12 families of mammals were confirmed in/around the area by document survey, and among them 19 species in 10 families of mammals were important academically. 340 species in 55 families of birds were confirmed, and among them 79 species in 29 families of birds were important academically. 3 species in 3 families of amphibians, and 6 species in 4 families of reptiles were confirmed, and among them 1 species of amphibian was important. 873 species in 135 families of land insects were confirmed, and among them 20 species in 11 families were important. 1055 species in 115 families of plants were confirmed, and among them 126 species in 46 families were important. Most of vegetation was 9 or more in degree of naturalness. The peripheral area of Kaibetsu-Dake is the plant colony area specified by the 2nd basic survey on natural environmental conservation (Environment Agency). (NEDO)

Fiscal 1996 report on the comprehensive invetigational research on medical instruments. Development of a trace collection/microanalysis system of blood, etc.; development of a high accuracy three dimensional image diagnosis system; development of a low invasion operation supporting system; development of artificial internal organ technology; 1996 nendo chosa hokokusho sogo chosa kenkyu (iryo kiki). Ketsuekinado biryo saishu/biryo bunseki system kaihatsu, koseido sanjigen gazo shindan system kaihatsu, teishinshu shujutsu shien system kaihatsu, jinko zoki gijutsu sogo kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

In accordance with the rapidly advancing phenomena of decreasing in number of child and aging in Japan, enhancement in quality of medical care and welfare is an issue to be urgently considered, and importance of the support by technology of medical instruments is increasing. The purpose of this research is to extract subjects of the element technology, which will be important strategically and in the long run, from two viewpoints of the needs side and seeds side to study the course of the development of medical instruments. For this, questionnaires were sent out to learned persons in charge of work connected with medical care to grasp the needs for the future development of medical instruments. Based on them, the paper extracted subjects of the element technology which are considered to become strategically important in Japan. The report outlined the investigational research and arranged the methods and results of the survey of the needs for the development of medical instruments. Next, the paper described the method to extract important subjects of the element technology from the needs survey, and then arranged important subjects of the element technology extracted through the study in the committee. At last, the paper generalized the investigational research and summarized the remaining subjects, etc. at the same time. 11 tabs.

Report on survey in fiscal 2000 on the survey and research on technology to integrate artificial bone system with living organism, taking individual difference into account; 2000 nendo kotaisa wo koryoshita jinkokotsu system no seitai tekigoka gijutsu ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Survey and research have been performed on artificial bones as to the bone growth and bone absorption mechanism, nature demanded in artificial bones, and ideal concept of artificial bones. As a result of the survey, the following matters were made clear: Ti alloy draws high attention as the artificial bone material; and up-to-date research is being made to promote fusion of the Ti alloy bone with natural bones by putting apatite covering on the Ti alloy bone by means of chemical treatment, wherein porous layers are produced on the surface that do not form inclination from a dense bone to a sponging bone, or from high density to low density, but produce the reverse inclination, as in the cross section structure of natural bones. Reports have been given from the dentistry, oral surgery, plastic surgery, and orthopedic surgery on the followings: a fact that magnesium affects greatly the stimulation of osteoblasts; a case where absorption of the mandibular bone has been created clinically due to Ti-made mini-plate; and a case where even Ti has been eluted into soft tissues. Artificial bones made of magnesium structure is being studied as one of the solutions thereof. (NEDO)

Fiscal 1999 basic survey report for promotion of joint implementation. Project for overall loss reduction in Myanmar for thermoelectric power during transmission and distribution; 1999 nendo Myanmar koku karyoku sohaiden denryoku sonshitsu sogo teigen project hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With connection to the clean development mechanism (CDM) taken into consideration, a study is made about achieving greenhouse gas reduction in Myanmar through power generation facility heat efficiency improvement and power loss reduction. Taken up in the study are the Shwedaung power plant, the Mann power plant, and the power transmission system in the Mandalay District. The profitability of thermoelectric power facility improvement is calculated using the financial internal rate of return (FIRR), derivable from the cost of thermoelectric power facility improvement and the convenience to be created thereby, and using the opportunity cost in Myanmar. The result is then subjected to a feasibility study. Most effective for CO2 reduction is the addition or installation of advanced compound cycle power generation facilities which are also excellent in heat efficiency and power generation cost. The FIRR of thermoelectric power facility improvement is 9.4-12.8%, which means the effort is worth investment. Measures for decreasing power loss during transmission include the use of higher voltages, laying of new lines, employment of conductors thicker in size, and the installation of phase modifiers. The economic internal rate of return (EIRR) and FIRR are calculated for the study of feasibility. An analysis covering a 10-year period results in a 20.41% EIRR (exceeding the socially accepted discount rate of 10%) and a 17.56% FIRR (exceeding the general loan interest of 15%), which means that there is feasibility. (NEDO)

FY 1998 report on the comprehensive analysis in the geothermal development promotion survey. Tertiary. No.C-3 Akinomiya area; 1998 nendo chinetsu kaihatsu sokushin chosa sogo kaiseki hokokusho. No.C-3 Akinomiya chiiki (Dai 3 ji)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-01-01

The geothermal development promotion survey was conducted in the Akinomiya area, Ogachi county, Akita prefecture, and the FY 1998 results were summed up. In the surface survey, geology/electromagnetism/precision gravity survey was made as supplementary survey, and re-analysis of 3D models was made. In the well survey, three wells of N10-AY-6 to N10-AY-8 were drilled to conduct the core examination, temperature/pressure logging, sampler logging, short-term jetting test, etc. Also conducted were the reservoir evaluation, environmental effect survey, etc. by pressure monitoring and water level observation. The results of the comprehensive analysis predict the following. In the Akinomiya area, there exists heat source in deep parts around Mt. Yamabushi-dake and Mt. Takamatsu-dake; Being given heat from this heat source, rocks, ground water and volcanic gas react on each other to form geothermal fluids. It is presumed that high temperature geothermal reservoirs exist in the east of the area. Moreover, the pressure distribution indicates that the Akinomiya reservoir and Wasabizawa reservoir can be a chain hydraulically. On the other hand, the west of the area is the low temperature and heat conductive area, and therefore, there seem to be no high temperature fluids there. (NEDO)

FY 1999 report on the comprehensive analysis of the geothermal development promotion survey. Forth. No.C-3 Akinomiya area; 1999 nendo chinetsu kaihatsu sokushin chosa sogo kaiseki hokokusho. No. C-3 Akinomiya chiiki (Dai 4 ji)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-01-01

As part of the geothermal development promotion survey, the comprehensive analysis was made on the survey of the existence amount of geothermal resource in the Akinomiya area, Ogachi town, Akita prefecture, which was conducted in FY 1999. In the evaluation of reservoirs, the following were carried out: comprehensive analysis of various data on the surface survey, well exploration, etc., which were stored in surveys from the primary to the forth, modification/construction of geothermal system models, numerical simulation using 3D models, etc. In the long-term jetting test, production/reduction tests were conducted using N9-AY-3 and N10-AY-8 as production wells and N8-AY-1 and N10-AY-6 as reduction wells. The results of the comprehensive analysis were outlined as follows. The distribution of high temperature zones promising as areas for geothermal development was grasped. The distribution of the main fracture structure underground was grasped. A total amount of 124t/h steam was confirmed by short/long term jetting tests. In the simulation of prediction of production, the result was obtained that there was potential power generation of 30MW in the Akinomiya area alone and 60MW both in the Akinomiya area and the Wasabizawa area. (NEDO)

Fiscal 1999 basic survey for promotion of joint implementation. Overall study report on energy saving and CO2 reduction at Indocement Company; 1999 nendo Indo cement ni okeru shoene CO{sub 2} sakugen sogo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

A study is made about the feasibility of energy saving and CO2 reduction at the Citeureup Plant of the Indocement Company, Indonesia. Future embodiment of a clean development mechanism (CDM) is also discussed. Points examined for improvement involve air quenching clinker cooler (AQC) efficiency (mixing of raw materials, use of combustion control technology, and modification into a new type AQC); the finishing process (installation of a preliminary clinker crusher and a high-efficiency classifier); and waste heat cogeneration using AQC exhaust. The amount of energy to be saved will be 61,866 tons/year in oil, promising a 10.9% energy saving and CO2 reduction. The project requires a fund of 5,988,025,000 yen in total. The financial internal rate of return (FIRR) based on the environmental special yen credit is a little low, but the payout period of 11 years is reasonable. A similar result is obtained when export financing by the ex-Exim Bank is studied. A general loan is not proper in view of overall profitability. With precedents showing that it is near impossible for such a project to enjoy environmental special yen credit, it is necessary for the Japanese Government to build a CDM-oriented system under which environmental special yen credit will be offered to private sectors. (NEDO)

Report on fiscal 2000 geothermal development promotion survey. No. C-5 Appi district environmental impact survey (1st phase); 2000 nendo chinetsu kaihatsu sokushin chosa hokokusho - No.C-5. 1. Appi chiiki kankyo eikyo chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-08-01

For the survey of weather in the Appi district, Iwate Prefecture, observation data covering the last decade were collected at weather stations and the like, and characteristics of weather, climate, and natural earthquakes were learned. In the survey of fluctuation in the spa water level, studies were made about fluctuation in water temperature, spring water, and river water, and basic data were collected for the examination of the impact to be generated by geothermal exploration well boring and short-term discharge tests. In the survey of animal and vegetables, the habitation and distribution of animals and vegetables at sites planned for geothermal well boring were investigated, and data were collected for the evaluation of the impact to be imposed on them by well boring or the like. In the survey dealing with nature conservation and landscape, laws and regulations governing nature conservation were collected and put in an easy-to-use order, and seasonal changes in the natural landscape were photographed and recorded. In the survey of noise/vibration and ground fluctuation, the background values were measured prior to the implementation of geothermal well boring, discharge tests, and so forth. (NEDO)

Effect of temperature on degradation of musty odour compound producing by cyanobacteria, Phormidium tenue by microflagellate, Monas guttula; Benmochu Monas guttula ni yoru kabishu sansei sorui Phormidium tenue no bunkai ni oyobosu ondo no eikyo

Energy Technology Data Exchange (ETDEWEB)

Lee, B.; Sudo, R. [Tohoku University, Sendai (Japan). Faculty of Engineering; Sugiura, N. [Ibaraki Prefectural Waterworks, Ibaraki (Japan); Inamori, Y.; Nishimura, O. [National Inst. for Environmental Studies, Tsukuba (Japan); Higashi, T. [University of Tsukuba, Tsukuba (Japan). Institute of Applied Biochemical

1998-04-10

Biodegradation characteristics of cyanobacteria, Phormidium tenue and its metabolites, 2-methylisoborneol (MIB) by protozoan microflagellate, Monas guttula, and the effect of temperature on them were examined in batch culture experiment. The flagellate was found to predate on P. tenue favorably as a food source within a wide temperature range from 10degC to 30degC. Specific growth rate ({mu}) and generation time (t{sub d}) of the flagellate were 4.6 day{sup -1} and 3.5 h{sup -1}, respectively at 20degC and 30degC, whereas in the case of 10degC the lag values of {mu} and t{sub d} were obtained by 1.9 fold in comparison with the removal ratio of 61% at the first cultivation day and that of 99% at the 2nd day at 30degC, while at 20degC the removal was only about 30% in the first day, but P. tenue could be perfectly reduced at the 2nd day. Although the reduction rate of the P. tenue was slow at the lower temperature of 10degC, the removal reached 98% in the 7th day. Removal rate of P. tenue by the flagellate increased with the increase in temperature and reached the maximal value with 4.0 h{sup -1} at 30degC. The flagellate could contribute to the degradation of MIB, although the degradation was lower than that of P. tenue. It was found that the microflagellate could favorably predate on P. tenue and degrade its metabolite, MIB emitting musty odor in a wide range of temperature. 27 refs., 8 figs., 3 tabs.

FY 1998 geothermal development promotion survey. Report on the environmental effect survey (animals/plants, No. B-7 Kuwanosawa area); 1998 nendo chinetsu kaihatsu sokushin chosa. Kankyo eikyo chosa hokokusho (doshokubutsu, No.B-7 Kuwanosawa chiiki)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This survey was conducted to estimate effects of drilling of geothermal exploration well on the environment, aiming at grasping the present state of environmental elements before the survey/development. As a result of the literature survey, the following distribution were confirmed in the fauna: 5 orders 10 families 19 species in the mammalia, 10 orders 25 families 73 species in the aves, 1 order 3 families 6 species in the reptilia, 2 orders 6 families 9 species in the amphibia, and 17 orders 179 families 719 species in the insecta. In the flora, a distribution of 132 families 670 species was confirmed. The results of studying the above indicated that in the fauna, there were 10 species such as antelope as valuable animal in the area surveyed and that it is necessary to pay much attention to the environmental preservation of the habitat for those animals in the well drilling associated with geothermal survey. In the flora, the 13 valuable animals selected as animal having a fear of extinction in the 'plant-version red list' were confirmed in the area surveyed and the periphery. Further, as to the plant colony, there are no important colonies in terms of preservation. In well drilling, important things are efforts exerted to restore to the original state of the area altered, prevention of the washed-away of mud water, etc., and efforts exerted to preserve the environment of vegetation. (NEDO)

Study of the oil flow and the bearing temperature in engine. Part 3. Influence of the bearing designs; Engine ni okeru jikuuke yuryo oyobi jikuuke ondo ni kansuru ichikosatsu. 3. Jikuuke sekkei yoso no eikyo

Energy Technology Data Exchange (ETDEWEB)

Watanabe, K; Kawai, K; Sasaki, S [Taiho Kogyo Co. Ltd., Aichi (Japan)

1997-10-01

It is necessary to find the bearing design so that the bearing temperature drops most efficiently by making the proper oil flow. We measured the oil flow and the bearing temperature using the narrow width bearing the bearing with small oil relief , the bearing with shallow circumferential microgrooves (the microgrooved bearing), the narrow width bearing with microgrooves. And further, we measured the variation of the oil flow every 5-15deg crank angle and searched for the efficient oil flow. As the result the bearing temperature using the microgrooved bearing dropped most efficiently. 3 refs., 13 figs., 5 tabs.

Effects of substrate concentration, specific surface area and hydraulic loading on the treatment efficiency in a submerged biological filter. Sesshoku bakkiho no shori koritsu ni taisuru kishitsu nodo, hihyo menseki oyobi suiryo fuka no eikyo

Energy Technology Data Exchange (ETDEWEB)

Iyo, T; Ono, S; Yoshino, T [Kitasato University, Kanagawa (Japan). School of Hygienic Science

1991-06-10

Effects of substrate concentration, specific surface area, and hydraulic loading, which are major factors influencing treatment efficiency in a submerged biological filter, were analyzed through the test with a special apparatus. In the test, the wall of the submerged biological filter was regarded as the contact material, and the specific surface area was changed by adjusting the sectional form of the filter. Using specimens from actual plant reservoirs, treatment efficiency for each case of three kinds of substrate concentration and hydraulic loading was measured. BOD removal rate was lower with smaller specific surface area. It was conspicuous particularly with higher BOD concentration in influent water. After the multiple regression analysis of the test results, the multiple regression equation to estimate BOD residual rate from three variates such as BOD concentration, specific surface area, and hydraulic loading was obtained. When 200mg l as BOD concentration and 50m{sup 2} m{sup {minus}3} as specific surface area were applied in this equation, the result almost agreed with the tendency obtained from data of actual plants. 6 refs., 4 figs., 1 tab.

Local approach to brittle fracture under residual stress field. Assessment of pre-loading effect; Local approach no tekiyo ni yoru zanryu oryoku wo motsu buzai no zeisei hakai kyodo hyoka. Yokaju no eikyo no hyoka

Energy Technology Data Exchange (ETDEWEB)

Yamashita, Y.; Sakano, K.; Onozuka, M. [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan); Minami, F. [Osaka University, Osaka (Japan)

2000-01-01

The effect of residual stresses on brittle fracture was investigated on the basis of the Local Approach. Compressive residual stress was introduced by pre-loading and the subsequent fracture test conducted with a 780 MPa class steel. Preloading apparently increased the critical load and critical CTOD at the onset of brittle fracture initiation. The Weibull stress criterion was used to evaluate the brittle fracture resistance of the pre-loaded specimen. The critical Weibull stress is a material property independent of test conditions with and without pre-loading. Using the Weibull stress criterion, the critical CTOD of the pre-loaded specimen can be predicted from test results of the specimen without pre-loading. (author)

New concept of combustion technology in small DI diesel engines. 4th Report. Effects of fuel injection rates on MK combustion; Kogata chokufun diesel kikan no shinnensho concept. 4. Funsharitsu no MK nensho eno eikyo

Energy Technology Data Exchange (ETDEWEB)

Kimura, S; Matsui, Y; Kamihara, T [Nissan Motor Co. Ltd., Tokyo (Japan)

1997-10-01

A previous paper showed that EGR cooling and a low compression ratio which prolongs the ignition delay can expand the area of the new combustion concept. Experimental investigations were conducted in this research to examine the effects of the fuel injection rates, the injection pressure and the injection duration, on the exhaust emissions of an engine incorporating the MK concept The results showed that a higher injection pressure was effective in reducing NOx and particulate matter (PM) under MK combustion conditions. 10 refs., 9 figs., 1 tab.

Report for fiscal 1981 on comprehensive survey for nationwide geothermal resources. Survey on radar imaging method - geothermal analysis conception design (Appendix); 1981 nendo zenkoku chinetsu shigen sogo chosa hokokusho. Radar eizoho chosa (chinetsu kaiseki gainen sekkei furoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-10-01

This paper explains different theoretical calculation methods used in gravity and magnetic force data analysis in geothermal resources survey. Analyzing the gravity data and the magnetic force data is capable of being applied with the potential theory. The increased speed and capacity of recent computers make easier the conversion of data into wave number zone. In relation with heavy magnetic force analysis, the paper explains such items as basic handling, IGRF remainder calculation, methods for topographic correction, conversion of primary and secondary polar magnetism and conversion of pseudo-gravity, coherent analysis, spectral ratio method, estimation of spectra by using MEM, spectrum moment method, heavy magnetic force simultaneously analyzing type modeling, constraint inversion method, and other methods. The paper further explains the sequential approximation method in magnetization calculation, methods for calculating equivalent magnetization distribution (methods by Bhattacharyya and Chan, and Nakatsuka), method for calculating equivalent magnetization distribution (method by O'Brien), primary and secondary polar magnetism conversion relation formulas, and theoretical calculation of spectral ratio. (NEDO)

Report for fiscal 1980 on comprehensive survey for nationwide geothermal resources. Survey on Curie point method (Associated material - operation flight report); 1980 nendo zenkoku chinetsu shigen sogo chosa hokokusho. Curie tenho chosa (futai shiryo sagyo shinchoku hokokusho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-10-01

With an objective to identify the status of distribution of deep underground thermal structure, aerial magnetism investigations were executed in the south Kyushu area, and data used in the Curie point method were collected. This paper summarizes the progresses and achievements of the work during the investigation. The report for April 1981 summarized preparation of equipment and materials by EG and G Geometrics Corporation, and the work schedules with the Idemitsu Geothermal Development, Petroleum Resources Development, and Naka-Nippon Airways. The report for April 22 compiled the site preparation and the test flight. The report for April 28 compiled the calibration and magnetism compensation flight. The report for May 5 compiled the implementation of the second flight , and the result of survey for 292 km in total. The report for May 10 compiled the implementation of the third to fifth flights, and the results of measurements for 584 km, 519 km and 360 km, respectively. The report for May 18 compiled the implementation of the sixth to eighth (final) flights, and the results of measurements for 513 km, 584 km and 68 km, respectively. (NEDO)

FY 2000 report on the results of the project to promote the comprehensive management of petroleum products. Development of a risk assessment system; 2000 nendo sekiyu seihin sogo kanri suishin jigyo seika hokokusho. Risk hyoka system kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The R and D were conducted on the system to assess risk of chemicals which considers the human health, environment, etc., and the FY 2000 results were reported. In this fiscal year, the goal of the study was to establish a system of user-friendly interface, easy-to-use system components and data access methodology. As to the details of the system, additional assessment items on the human health were found and surveyed, and the development of a new system for the assessment of acute exposure was started. Relating to the handling of various data on toxicity, physical properties, etc., reference is to be made to the database of National Institute of Technology and Evaluation, MITI, as a base. Concerning the simple assessment corresponding to the PRTR method, almost all 435 chemicals designated by the PRTR act were to be included in the internal database. As to the development of the system, the simple assessment system corresponding to the PRTR method was developed, and a testing system, {beta} version, was completed. Further, the development of a 'site-specific assessment system' was started which considers the geological/meteorological situation of the site. (NEDO)

International research cooperation project. Assessment report on the R and D of the comprehensive development/utilization technology of energy of gas hydrate resource; Gas hydrate shigen no energy sogo kaihatsu riyo gijutsu no kenkyu kaihatsu hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

As to 'the R and D of the comprehensive development/utilization technology of gas hydrate resource,' assessment was conducted and reported from an aspect of the third party. This R and D is a timely project being aimed at establishing the basic technology on gas hydrate from both aspects of fundamental research and practical research. In the development of gas hydrate resource in the tundra zone, the development of measuring methods for thermal conductivity and dielectric constants advanced the establishment of a guide for exploration and possibilities of assessment of the resource amount. In the development/production, it can be said that the knowledge/information collected by exchanging methane in gas hydrate with CO2 means no needs for new supply of heat and also contributes to the isolation of CO2. As to the utilization technology, the results were rated very high also internationally of tackling the quantitative evaluation method at molecular levels of the gas included in hydrate using Raman spectroscopy to establish the industrial gas separation method using the low-temperature environment in the tundra zone. (NEDO)

General evaluation survey report on fiscal 1998 investigation of geothermal development and promotion. No.C-3 Akinomiya area (Third); 1998 nendo chinetsu kaihatsu sokushin chosa sogo hyoka chosa hokokusho. No.C-3. Akinomiya chiiki (dai 3 ji)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-01-01

With Akinomiya area (11.4 km{sup 2}) selected in Akita prefecture as the survey C area in fiscal 1996, the first survey was conducted. This paper is a summary of memorandum from an advisory standpoint on the evaluation survey concerning the fiscal 1998 investigation results. The contents of the survey are geological investigation, precision gravity exploration, soil gas investigation, electromagnetic exploration, fluid chemical investigation, well drilling and short-term eruption test. An alteration zone was recognized around the place where clay minerals used to be mined, with the center of the zone situated 500-600 m east of a fault. The alteration condition of Akinomiya area seems to be different from that of Doroyu Wasabisawa area. The supplementary gravity survey was carried out at total 58 points in fiscal 1998. It is desirable to set supplementary measuring points over a wide surrounding area for a depth structure analysis. Also performed was a study of mercury concentration in the soil gas. While CSAMT and TDEM methods were employed for the electromagnetic exploration, a suitable method should be carefully selected for a wide area high-density exploration. Consistency with adjacent areas is essential in preparing investigation items particularly for a geothermal model. (NEDO)

FY 2000 report on the results of the project to promote the comprehensive management of petroleum products. Development of a risk assessment system; 2000 nendo sekiyu seihin sogo kanri suishin jigyo seika hokokusho. Risk hyoka system kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The R and D were conducted on the system to assess risk of chemicals which considers the human health, environment, etc., and the FY 2000 results were reported. In this fiscal year, the goal of the study was to establish a system of user-friendly interface, easy-to-use system components and data access methodology. As to the details of the system, additional assessment items on the human health were found and surveyed, and the development of a new system for the assessment of acute exposure was started. Relating to the handling of various data on toxicity, physical properties, etc., reference is to be made to the database of National Institute of Technology and Evaluation, MITI, as a base. Concerning the simple assessment corresponding to the PRTR method, almost all 435 chemicals designated by the PRTR act were to be included in the internal database. As to the development of the system, the simple assessment system corresponding to the PRTR method was developed, and a testing system, {beta} version, was completed. Further, the development of a 'site-specific assessment system' was started which considers the geological/meteorological situation of the site. (NEDO)

Report on final evaluation of industrial science and technology research and development system. Comprehensive basic technologies for development of ocean resources. Manganese nodule exploitation system; Kaiyo shigen sogo kiban gijutsu (mangan dankai saiko system). Saishu hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-07-01

Described herein are the final evaluation results of the basic research and development of the system for exploiting manganese nodules as one of ocean resources. A 9-year project was started in the FY 1981 to establish the techniques to efficiently, economically exploit Mn nodules on a commercial basis, which are occurring on deep sea bottoms (4,000 to 6,000 m deep), in order to stably supply non-ferrous metallic resources, e.g., Ni, Cu, Co and Mn, which are essential for economic activities of Japan. Originally, the UN convention related to ocean laws raised development of unique exploitation techniques as the prerequisite condition for obtaining the right to develop Mn nodules. However, the situations around development of Mn nodules were changed since then, to devalue objects, significance and urgency of this project. The fourth amendment of the basic plans decided to suspend the comprehensive ocean tests in 1996, and to implement only the ocean/land tests in which part of the individual elementary techniques were combined. Therefore, the technological validation of the overall system could not be done sufficiently, and degree of achievement of the project is low, viewed from insufficient prospects of the commercial production. However, this project produced good results in individual elementary techniques, which are of significance for the resources policies. (NEDO)

Investigations in fiscal 1983 on promotion of geothermal development. Part 1. Report on investigation of fumarolic environmental effects in Oku-Aizu area; 1983 nendo chinetsu kaihatsu sokushin chosa. 1. Okuaizu chiiki funkichu kankyo eikyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1984-03-01

As part of the investigations on promotion of geothermal development, surveys have been carried out in the Oku-Aizu area to identify the existence and/or extent of effects of collecting geothermal fluids above the ground imposed on the environment, such as the natural ecological system. The investigated area is an area of 60 km{sup 2} covering Kawanuma County and Onuma County in Fukushima Prefecture, a mountainous area with undulations. The investigation result may be summarized as follows: the area shows the inland climate and has snow fall as much as 2 m in winter; according to the H2S diffusion prediction, the concentration thereof on the land in seasonal average is 0.7 ppm at maximum, which is a value presenting no problems. No fumarolic effects of SO2 were identified, and floating dust and Hg showed values that present no problems. With regard to water quality during and after the blowout test, no effects of blowout return were identified. The noise level was 41 to 45 phones at a place 100 m distant, and the vibration level has become the lower detection limit at a place 50 m distant. Leveling has discovered no ground movement. No variation in major constituents in thermal spring water was verified before and after the blowout test. (NEDO)

Studies of initial stage in coal liquefaction. Effect of decomposition of oxygen-functional groups on coal liquefaction; Ekika hanno no shoki katei ni kansuru kenkyu. 3. Gansanso kannoki no bunkai kyodo to ekika hanno eno eikyo

Energy Technology Data Exchange (ETDEWEB)

Komeiji, A.; Kaneko, T.; Shimazaki, K. [Nippon Brown Coal Liquefaction Co. Ltd., Tokyo (Japan)

1996-10-28

Pretreatment of brown coal in oil was conducted using 1-methyl naphthalene or mixture of tetralin and 1-methyl naphthalene as solvent at temperatures ranging from 300 to 430{degree}C under nitrogen atmosphere. Effects of the solvent properties on the structural change of oxygen-functional groups (OFG) and coal liquefaction were investigated by means of quantitative analysis of OFG and solid state {sup 13}C-NMR measurement. When hydrogen transfer from solvent was insufficient, it was suggested that brown coal molecules loose their hydrogen to be aromatized. While, at lower temperatures ranging from 300 to 350{degree}C, hydrogen contained in brown coal molecules was consumed for the stabilization of pyrolytic radicals, and the deterioration of liquefaction was not observed. When hydrogen transfer from solvent was insufficient at higher temperatures above 400{degree}C in nitrogen atmosphere during pretreatment in oil, crosslinking like benzofuran type was formed by dehydration condensation of hydroxyl group in brown coal, to deteriorate the liquefaction, remarkably. The addition of donor solvent like tetralin decreased the formation of crosslinking like benzofuran type, which suppressed the deterioration of liquefaction. 8 refs., 5 figs.

Survey on acceleration of geothermal development in fiscal 1998. Report on survey for influence on environment (No. B-7, Kuwanosawa district); 1998 nendo chinetsu kaihatsu sokushin chosa.Kankyo eikyo chosa hokokusho (No. B-7 Kuwanosawa chiiki)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

A survey was performed on the current situation in the Kuwanosawa district in Akita Prefecture to identify influence on the surrounding environment due to drilling of geothermal structure testing wells. The survey on animals covered mammals of five divisions, 10 families and 19 species, Aves of ten divisions, 25 families and 73 species, reptiles of one division, 3 families and 6 species, Amphibia of two divisions, 6 families, 9 species, and Insects of 17 divisions, 179 families and 719 species. Precious animals of a several species including black salamander were identified. In the plant survey, 132 families and 670 species were identified, with several species listed as the precious plants. In the survey of hot springs, those at three locations were all high-temperature hot springs at as high as 53.8 to 96.9 degrees C. Amount of discharge, pH and electrical conductivity differ largely by the hot springs. The hot spring in Takamatsu did not show large variation throughout the survey period. The Ogura Inn at Doroyu Spa has small variation in pH and hot spring temperature, but large variation in the amount of discharge and Al{sup 3+} concentration. Correlation was recognized between hot spring temperature and amount of discharge, between hot spring temperature and anion, between amount of discharge and electric conductivity, and between amount of discharge and anion. (NEDO)

FY 2000 report on the R and D of the particulate utilization type creation technology of biological connective substances. Survey of the technical trend overseas; 2000 nendo biryushi riyogata seitai ketsugo busshitsu nado sosei gijutsu no kenkyu kaihatsu seika hokokusho. Kaigai gijutsu doko chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The paper summarized the reports on the results of Japanese engineers' participating in the related scientific meetings held overseas as a survey report on the trend of the overseas technology. The scientific meetings they participated in were: 1) Impact of Genomics on Medicine and Pharmacogenomics Europe (Amsterdam; May 15-26, 2000), 2) Drug Discovery Technology 2000 (Boston; August 10-20, 2000), 3) Biotechnology 2000 (Berlin; September 3-12, 2000), 4) PacificChem 2000 (Hawaii; December 14-21, 2000), 5) 4th Winter Conference on Medicinal and Bioorganic Chemistry (Seattle; January 27 - February 4, 2001). Impact of Genomics on Medicine was composed of the following five fields: microarrays, proteomics, functional genomics and target validation, genetic variation technology, and applications of SNP analysis (joint session). Pharmacogenomics Europe was composed of the following four fields: applications of SNP analysis (joint session), SNP assays, targets and compounds, and clinical applications. (NEDO)

FY 2000 report on the R and D of the particulate utilization type creation technology of biological connective substances. Survey of the technical trend overseas; 2000 nendo biryushi riyogata seitai ketsugo busshitsu nado sosei gijutsu no kenkyu kaihatsu seika hokokusho. Kaigai gijutsu doko chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The paper summarized the reports on the results of Japanese engineers' participating in the related scientific meetings held overseas as a survey report on the trend of the overseas technology. The scientific meetings they participated in were: 1) Impact of Genomics on Medicine and Pharmacogenomics Europe (Amsterdam; May 15-26, 2000), 2) Drug Discovery Technology 2000 (Boston; August 10-20, 2000), 3) Biotechnology 2000 (Berlin; September 3-12, 2000), 4) PacificChem 2000 (Hawaii; December 14-21, 2000), 5) 4th Winter Conference on Medicinal and Bioorganic Chemistry (Seattle; January 27 - February 4, 2001). Impact of Genomics on Medicine was composed of the following five fields: microarrays, proteomics, functional genomics and target validation, genetic variation technology, and applications of SNP analysis (joint session). Pharmacogenomics Europe was composed of the following four fields: applications of SNP analysis (joint session), SNP assays, targets and compounds, and clinical applications. (NEDO)

Achievement report for fiscal 1998. Research and development of technologies for creating new bioaffinity molecules using submicron beads (Energy use rationalization related technology practicalization); 1998 nendo biryushi riyogata seitai ketsugo busshitsunado sosei gijutsu no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika kankei gijutsu jitsuyoka kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In the effort to develop chemical substance/bioreceptor analysis technology using submicron beads, polystyrene core/polyglycidyl methacrilate beads are used in a study started about a detachable spacer using newly developed fixation technology. In the development of bioaffinity chemical substance refining technology, two kinds of sugars and several kinds of aromatic aldehydes serve as building blocks in the construction of a library, and studies are made of analyses using liquid chromatography and mass spectrography. In the development of novel substance creation technology based on information on the analysis of chemical substance/bioreceptor, in an effort at developing technologies for creating novel function provided chemical substances, heterocyclic compounds, alkaloids, and sugar compounds are selected and their syntheses in the liquid phase and solid phase are studied, which is again for the construction of a library. (NEDO)

Fiscal 1998 industrial science and technology R and D theme (University coordination type). Research report on R and D of technologies for creating new bioaffinity molecules using submicron beads; 1998 nendo biryushi riyogata seitai ketsugo busshitsu nado sosei gijutsu no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This report summarizes the fiscal 1998 result on the entrusted research 'R and D of technologies for creating new bioaffinity molecules using submicron beads' based on 'Industrial science and technology R and D system.' As for development of technologies for analyzing chemical- biomolecule complexes using submicron affinity beads, for molecule design of DNA to be connected with cisplatin, telomere DNA was employed as a target DNA of cisplatin, and cisplatin-modified DNA (Pt-DNA) was synthesized. Reaction condition for Pt-DNA connected beads was established, and affinity beads with Pt-DNA were prepared. As for development of organic receptor refining technology, proteins bound to cisplatin-DNA were preliminarily analyzed, showing that the Pt-DNA is a proper target chemical substance. It is the first evidence that certain proteins recognize cisplatin-damaged telomere DNA. In addition, introduction of the equipment for developing analysis technology of binding domains, development of technology to create organic receptors with new functions, and general research on the titled technologies were carried out. (NEDO)

NEDO Forum 2001. Session on development of energy and environmental technologies (For promotion of comprehensive development of hydrocarbon-based energy); NEDO Forum 2001. Energy kankyo gijutsu kaihatsu session (tanka suisokei energy no sogo kaihatsu suishin no tame ni)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-09-20

The presentations made at the above-named session of the NEDO (New Energy and Industrial Technology Development Organization) forum held in Tokyo on September 20, 2001, are collected in this report. Pointed out in a lecture entitled 'How technology development for hydrocarbon-based energy resources should be' was the need of technologies for clean energy production; CO2 emission reduction; NOx, SOx, soot, and dust reduction; and the expansion of exploitation of resources now left unused. Reported in a lecture entitled 'Cooperation with China on coal liquefaction' were the result of a coal liquefaction demonstration plant feasibility study conducted for coal from Inner Mongolia, and so forth. Reported in a lecture entitled 'Development of coal oil upgrading technology' were the result of the operation of a test plant, and so forth. Reported in a lecture entitled 'Research and development of HyperCoal' were the result of HyperCoal manufacturing technology research and development, designing of a HyperCoal-fired gas turbine power generation system, and so forth. In addition, development of technology for high efficiency conversion of biomass energy and development of technology for refuse gasification/melting power generation were reported. (NEDO)

FY 1992 Report on results of the research and development of the technologies for creating/processing advanced biomaterials. Part 2; 1992 nendo senshin bio zairyo no sosei kako gijutsu no kenkyu kaihatsu seika hokokusho. 2. Sogo chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

This project is aimed at development of the materials which show functions in a living body by coating a substrate of, e.g., silica or glass, with layered novel peptide synthesized to include unusual amino acid required to have the functions. The existing peptide-related technologies are reviewed and the natural peptide list is prepared. A total of 15 literature is surveyed, and the contents are pigeonholed into 8 items; (1) prospects of peptide engineering, (2) designs of peptide structures, (3) technologies of peptide synthesis, (4) synthesis of unusual amino acid and inclusion into peptide, (5) analysis of peptide structures, (6) physiological activity of peptide, (7) development of peptide materials and function manifestation, and (8) information retrieval of natural peptide (comprising 30 amino acids or less). The item (2) involves analysis and prediction of hydrophobicity of oligopeptide, item (3) chemical synthesis of protein, and protease-aided condensation of dipeptide, and item (7) solar cells based on a photoelectric conversion material and pigment-sensitized colloidal titanium oxide. (NEDO)

FY 1994 report on the survey of geothermal development promotion. Complementary survey on the fracture system, etc. (Wasabizawa area); 1994 nendo chinetsu kaihatsu sokushin chosa sogo kaiseki hokokusho futai shiryo. Wasabizawa chiiki danretsu kei tou hokan chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-01

For the contribution to elucidation of the geothermal structure in the Wasabizawa area, Akita Prefecture, survey by the paleomagnetic measurement and fracture system measurement was conducted of the borehole cores and specimens of outcrop granite obtained from boreholes of N6-WZ-3 and N6-WZ-4. In the survey, the following were carried out: measurement of the core fracture system of N6-WZ-3 (102-1,505m) and N6-WZ-4 (507-1,556m), paleomagnetic measurement of 9 outcrop granite specimens and 16 core specimens, and k/Ar age determination of 3 outcrop granite specimens. As a result of the paleomagnetic measurement of outcrop granite, the magnetization azimuth of the schistose granodiorite distributed in Kuwanosawa was regarded as almost NS. The measured magnetization azimuth of the core specimen obtained from the same rock mass was also made NS-based, and measurement of the fracture in the neighborhood was made. As a result, it was found out that the NNW system was dominant in dikes and that there was the NE system in most of the small geothermal channels. The fracture system of well tended to develop around the boundary between granite and metamorphic rock, and it was thought that this part could be a reservoir if temperature conditions are prepared. (NEDO)

Experimental and numerical studies on aerodynamical noise in a high-speed elevator. ; Effect of apron on flow around elevator car. Kosoku elevator no kuriki soon ni kansuru kenkyu. ; Kagomawari no nagare ni oyobosu apron bu no eikyo

Energy Technology Data Exchange (ETDEWEB)

Matsuda, H.; Fukuyama, Y.; Miyasako, K.; Endo, M. (Toshiba Corp., Tokyo (Japan)); Yokono, Y. (Tokyo Institute of Technology, Tokyo (Japan). Research Laboratory of Precision Machinery and Electronics)

1993-08-25

For the purpose of reducing aerodynamic noise of a high-speed elevator, the flow around the elevator car was subjected to a flow visualization experiment and numerical simulation using a model simulating an elevator. The state of the flow in front of the door was observed by visualizing the field of flow around the model submerged in a water bath using a poster color tracer. Further, a wind tunnel experiment was carried out to observe the effects of flow at the side wall of the car. An oily agent using TiO2 as pigment was used for observing the pattern of oil film on the surface of the model and the observed results were recorded on a video tape. Since the oil solution is white, the place where the oil film is peeled by a strong shearing force exhibits a pattern of black color which is the color of the model substrate. Flow in front of the door is different depending on whether the car is in the upward motion or in the downward motion and affected by the presence of apron. During the downward motion of the car, the vertical vortices accompanying the flow detouring from the rear surface to the front surface of the apron are generated at both ends of the apron and thereby the streamlines are concentrated to generate accelerated flow in front of the door. Suppression of vertical voltices is important for reducing noise during downward motion. Peeled flow and vortex interference appear at the side and back of the car and forms a field of complex flow. 12 refs., 10 figs.

FY 1997 report on the survey of potential impacts of enlarging ASEAN on political and economic systems in South East Asia; 1997 nendo chosa hokokusho (ASEAN kakudai no Higashi Asia no seiji keizai chitsujo eno eikyo chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This report surveys potential impacts of ASEAN (Association of South East Asian Nations) on inter-ASEAN affairs and its external relations when ASEAN will enlarge its members to include all nations in South East Asia, and thus fully represent the region. For this purpose, the survey was conducted on Vietnam, Myanmar, Laos and Cambodia, which joined in 1995, from the viewpoint of their economic and political system, and their relations with other member countries. The nature of ASEAN has gradually transformed, in which all the countries in the region have increased and internal economic issues have been tackled. It has an aim to stimulate inter-ASEAN trade and induce foreign direct investment into ASEAN as a whole by reducing import duties on intra-ASEAN trade. Underlying in these, new development is a concern about growing economic and military power of China. ASEAN solidarity will work an leverage against China should change toward worse, and ASEAN will function as a regional stabilization factor. ASEAN is needed for the stability of both in economic and political order in East Asia. Japan has to further promote its cooperation with ASEAN to help its solidarity as an association. 24 refs., 21 figs., 25 tabs.

Fiscal 2000 report of investigation. Project for promoting international cooperation for global environment/Project for assessment on effect of climate change; 2000 nendo chikyu kankyo kokusai kyoryoku suishin jigyo / kiko hendo eikyo hyoka nado jigyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Assessment and examination were conducted on the scientific/technological aspect, environmental aspect and economic/social aspect concerning measures for mitigating climate change, as a part of international cooperation in global warming issues. In the development of assessment methods for cost analysis, it revealed that, in the activities for mitigating emission of greenhouse effect gases (GHG) or for increasing carbon sequestration, benefits of the mitigation sometimes surpassed their cost, allowing the society to benefit from the mitigation. In the examination of problems in technology transfer and their solutions, it was found that, in order to attain successful transfer, partnership among the parties interested was essential and that each government was capable of promoting such partnership. In the assessment of various policy options, the situation in the U.S. is such that the market aspect of GHG emission permit and credit trading is rather weak because of immaturity in a legal framework on GHG emission trading and because of undefinedness in the systems of the Kyoto Protocol and in the possibility of its validation. However, the reason enterprises are actively participating in the early market is that they plan a risk-hedge for example in anticipation of tighter regulations in the future. (NEDO)

Robust estimation of space influence model. Part 2. ; Synthesis of urban lattice data analysis for practical use. Kukan eikyo model no antei suiteiho. 2. ; Jikkenteki mesh data kaiseki system kochiku no tameno kukan sokan bunsekiho no taikeika

Energy Technology Data Exchange (ETDEWEB)

Aoki, Y.; Osaragi, T. (Tokyo Institute of Technology, Tokyo (Japan). Faculty of Engineering)

1991-07-30

In this study, a method for robust estimation of parameters of the space influence function model, which was possible to become unstable, was investigated by applying a principal component method. In order to carry out the robust estimation of parameters without the effect of multicollinearity, regression coefficients of principal components with small eigenvalue and with small single-correlation with dependent variables were required to forced to be zero in the estimation method by principal component. Through the case study using the real urban lattice data, the conventional method was compared with the principal component method. As a result, the latter method realized the excellent sabilization of spatial distribution patterns of estimation parameters and the simple interpretation of parameters. It also improved reliability since 95% confidence interval of the estimated value became smaller. This method was found to be effective as a basic measure to acheve the stability of parameters. 10 refs., 7 figs.

CFD prediction of heat island formation on growing Asian cities. Effect of urbanization in Shanghai; Kyodaikasuru Asia no toshi ni okeru heat island keisei ni kansuru CFD yosoku. Shanghai no toshika ga oyobosu eikyo ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Ojima, T.; Murakami, S. [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science; Mitsumoto, K. [Waseda University, Tokyo (Japan). School of Science and Engineering

1997-10-01

Study is conducted of the effect of change in land use and increase in artificial exhaust heat on heat island formation in Shanghai. Concerning the land use distribution in Shanghai, a point sampling survey was conducted in the 1930s using topographic charts, when the area was broken down into building-occupied region, paddy field, bare ground, and waters. In the 1990s, thanks to data from satellites, high-density and low-density urban regions have added. Calculation for Shanghai is performed, based on the rate of increase in Tokyo`s population and data predicted for Shanghai`s population, on the assumption that Shanghai`s population in the 2050s will grow 2.3 times larger than it is in the 1990s. The prediction thus produced indicates that the urban area in Shanghai in the 2050s will be as large as that of the present-day Tokyo that covers a 50km zone. Heat island formation prediction for Shanghai is worked out using computational fluid dynamics (CFD)-aided simulation. According to the prediction, while the maximum temperature in the 1930s was 29.6degC or 4degC higher than in the suburbs, it is 33.2degC or 7.6deg higher in the 1990s, and will be 34.4degC or 8.6degC higher in the 2050s. 16 refs., 11 figs., 1 tab.

Effects of air pollution on the health of regional inhabitants. Part I. Survey of disease state by Enquete. Taiki osen ga chiiki jumin no kenko ni oyobosu eikyo ni tsuite-dai ippo; anketo ni yoru shojo chosa

Energy Technology Data Exchange (ETDEWEB)

1973-01-01

From May to July 1972, the disease states of 2096 inhabitants (710 men and 1386 women) in the Fukushima Ward of Osaka City, where the concentration of sulfur trioxide in the air was (yearly average) 1.81 mg/day/100 sq cm and that of carbon monoxide was 5.3 ppM, and that of nitrogen dioxide was 5.3 ppM, were surveyed. The number of persons surveyed was 2.9% of all the inhabitants of the Ward. Twenty-two point one percent were in their thirties, 20.1% in their forties, 16.5% in their sixties, and 15.3% in their fifties. Those who experienced chest diseases were 2.9% of the total, and those with heart diseases were 1.5%. Non-smoking men were 31.7% of the total. The percentage of long-term complaints of cough and sputum was 11.8% in the eastern section, 11.2% in the northern section, 10.0% in the southern section, 6.8% in the western section of the Ward. The frequency of complaints was highest in the sixties (12.7%), followed by 11.5% in the fifties, 11.3% in the thirties, and 8.6% in the forties. The frequency of complaints from men was 11.1% and that from women was 6%. The frequency of complaints was 19.8% in smokers, 8.5% in those who smoked less, and 6.8% in non-smokers. The frequency of complaints classified by residential area showed 12.6% in industrial areas, and 7.8% in residential and commercial areas. The frequency of complaints of inhabitants who live along National Road No. 2 was relatively high, ranging from 15.0 to 18.8%, and the frequency of complaints of inhabitants was apparently higher than those of people who only work in the Ward.

Thermal boundary condition effects on forced convection heat transfer. Application of a numerical solution of an adjoint problem; Kyosei tairyu netsudentatsu mondai ni okeru netsuteki kyokai joken no eikyo. Zuihan mondai no suchi kai wo mochiita kosatsu

Energy Technology Data Exchange (ETDEWEB)

Momose, K.; Saso, K.; Kimoto, H. [Osaka University, Osaka (Japan). Faculty of Engineering Science

1997-11-25

We propose a numerical solution for the adjoint operator of a forced convection heat transfer problem to evaluate mean heat transfer characteristics under arbitrary thermal conditions. Using the numerical solutions of the adjoint problems under Dirichlet and Neumann conditions, both of which can be computed using a conventional CFD code, the influence function of the local surface temperature on the total heat transfer and that of the local surface heat flux on the mean surface temperature are obtained. As a result, the total heat fluxes for arbitrary surface temperature distributions and the mean surface temperatures for arbitrary surface heat flux distributions can be calculated using these influence functions. The influence functions for a circular cylinder and for an in-line square rod array are presented. 14 refs., 9 figs., 1 tab.

FY 1990 report on the survey of geothermal development promotion. Survey of environmental effects before jetting (No.34 - Kaminoyu/Santai area); 1990 nendo chinetsu kaihatsu sokushin chosa. No.34 Kaminoyu Santai chiiki - Funki zen kankyo eikyo chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-01-01

For the evaluation of effects of geothermal development on the peripheral environment in the Kaminoyu/Santai area in the southwest part of Hokkaido, survey of the present situation of the environment was made. As a result of the survey, as to the climate of this area, the mean temperature, precipitation, etc. were almost the same as those of the nearest meteorological office of Hakodate, and the wind velocity was lower. Concerning the air, the mean concentration of H{sub 2}S was 0.8-3.6 ppb, SO2 was less than the detectable limiting value, Hg was 0.018-0.12 {mu}g/m{sup 3}N in average, and suspended particulate was 0.014-0.028 mg/m{sup 3}. Each of them satisfied the environmental criteria and the control level. The water quality satisfied the AA type criteria at every point of the river surveyed. The noise/vibration at the time of well drilling were 47-50dB at 10m measuring point and less than the lower limit of measuring at measuring points farther than 50m measuring point/100m measuring point. Every hot spring was drilled and spontaneously welling, and variations in spring temperature/welling amount were comparatively small. Micro earthquakes of 495 were observed in 47 days in total. Besides, survey was made of animals, plants, soils, scenery, etc. (NEDO)

Report on achievements in fiscal 1998. Research and development of a technology to forecast environmental effect in association with isolation of carbon dioxide in oceans. (Surveys on development and research support on a technology to forecast environmental effect in areas in the vicinity of CO2 discharging points); 1998 nendo nisanka tanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu seika hokokusho. CO{sub 2} horyuten shuhen'iki no kankyo eikyo yosoku gijutsu no kaihatsu narabini kenkyu shien chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Atmospheric concentration of CO2 is increasing, and discussions are urged on measures to suppress emission of CO2 into atmosphere. While different CO2 fixing technologies may be conceived, there is a technology to utilize CO2 absorbing capability of ocean by discharging and dissolving CO2 artificially into middle layer of the ocean to separate CO2 from atmosphere. This technology is one of the technologies which are promising in the aspects of technology, economic performance, and possible amount of CO2 reduction. However, it is difficult to say that scientific and technological discussions have been given sufficiently on behavior of CO2 discharged into the ocean, effect of the discharge on environments, and CO2 separation capability of the ocean. Therefore, in the present research and development, a 'technology to forecast environmental effect in areas in the vicinity of CO2 discharging points' is developed to serve for acquiring technological prospect on the feasibility to realize the CO2 ocean separation by discharging CO2 into the middle layer of the ocean. The present fiscal year has performed researches on the following research and development items: elucidation of behavior of liquefied CO2 when discharged into the ocean, CO2 feeding and diluting technologies, indoor experiments on the effects of CO2 on ocean living organisms, and development of a model to forecast environments in areas in the vicinity of CO2 discharging points. (NEDO)

Report for fiscal 1982 on comprehensive survey for nationwide geothermal resources. Preparation of lineament density maps - radar image analyses - in north-eastern area; 1982 nendo zenkoku chinetsu shigen sogo chosa hokokusho. Lineament mitsudozu sakusei (radar gazo kaiseki (Tohoku chiiki))

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-03-01

Geological structure analysis maps and lineament maps were prepared on the north-eastern area and parts of the ancillary areas thereof by analyzing radar images of a 1 to 200,000 scale. With regard to the geological structures, analyses were performed by using as the original data the north look radar images for the three special geothermal areas to have prepared the geological structure analysis maps. The analysis of the radar images identified ground bed boundary lines in more detail than in the existing geological maps, and new discoveries were made available on faults. The lineament maps were compiled by implanting into respectively corresponding topographic maps the 24 N-S lineament maps made by the west look radar images for the whole surveyed areas, and the 16 E-W lineament maps made by the north look radar images for the special geothermal areas. Based on the clarity and characteristics deciphered on the images, the lineaments were classified into the major, minor, and subtle lineaments, which were indicated on the lineament maps. The lineaments were digitized by positions of the edge points, and the histograms and statistical tables were prepared by computer processing. (NEDO)

FY 1998 basic survey to promote the joint execution, etc. Overall repair plan of thermal power plants in Maritime Province of Russia; 1998 nendo kyodo jisshi nado suishin kiso chosa. Roshia Enkaishu ni okeru karyoku hatsudensho sogo kaishu keikaku

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For thermal power plants in Maritime Province of Russia, a repair plan for effective reduction of emission of greenhouse effect gas was worked out as a draft plan for the joint execution. The project is to be implemented for the additional installation/replacement of boilers at Vladivostok No. 2 power plant, construction of a power plant as a substitute for Partizansk power plant, and new construction of Ussuriisk power plant. The draft plan includes the new installation of two gas-fired boilers/replacement of existing boilers at Vladivostok No. 2 power plant, construction of 200MW cogeneration facility at Partizansk power plant, construction of 180MW cogeneration facility at Ussuriisk power plant, abolition of small-sized boiler station, etc. The reduction amount of the greenhouse effect gas emission based on this repair plan totaled 338 million tons in project. The effect against cost is US$ 4.75 per 1 CO2 ton at Vladivostok. (NEDO)

Assessment of effects of maturity of Japan`s economy and society and improvement in automotive fuel consumption on demand for automotive fuels; Nippon keizai shakai no seijukuka to nenpi kaizen ga jidoshayo nenryo juyo ni ataeru eikyo hyoka

Energy Technology Data Exchange (ETDEWEB)

Shimomura, S. [The Institute of Energy Economics, Tokyo (Japan)

1998-04-01

This paper evaluates impacts of the maturity of Japan`s economy and society and the improvement in automotive fuel efficiency on the demand for automotive fuels by FY 2010. Standard case and lower order case were examined. When the traffic volume of passenger cars in FY 1995 is assumed to be 100, it become 121 and 119 in standard and lower order cases, respectively. The traffic volume of lorries become 106 and 102 in standard and lower order cases, respectively, which showed a rather small growth. Deterioration rate of the fuel consumption was estimated by considering the difference in fuel consumption of new cars and existing cars. Although the fuel consumption will be lowered by FY 2000 when the cassation rate of ordinary passenger cars will rapidly increase, the impact will be lowered after that. For lorries for commercial use, the running fuel consumption will be gradually lowered due to the increased carrying capacity and vehicle weight a lorry with improving the transportation efficiency. Decreased running speed by traffic jam is also a cause of the deterioration of fuel consumption. When a policy of improvement in the fuel consumption is promoted in a background of CO2 issues, the fuel consumption of each vehicle will be gradually improved. The peak of fuel demand will be in FY 2005 by considering the changes in economical and social structures and the improvement in fuel consumption for the environmental protection. 5 figs., 3 tabs.

Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO (book on the handling / gas lift system). Report on the results of the R and D of the overall base technology of ocean resources (R and D of submarine oil drilling technology, etc.); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shine Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kaiyo shigen sogo kiban gijutsu no kenkyu kaihatsu (kaitei sekiyu kussaku gijutsu nado kenkyu kaihatsu) seika hokokusho (handling / gas lift system hen)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper conducted a R and D on the handling of drilling equipment in drilling/collecting of submarine oil and the gas lift of artificial oil extraction technology. As to each equipment of a barge style handling system, conducted were assembly/adjustment/trial run on land and pipe handling experiments on sea. In the experiment, confirmed were pipe transfer function, lifting function, fitting function, grasping function, etc. In the ocean experiment, studied were pipe bending stress, Karman vortex control effects, etc. Relating to the gas lift system, experiments were made on confirmation of fabrication/performance of air compressor. Moreover, a technique of air transportation to the blowing inlet of the gas lift pipe was established by developing an air blowing system and fabricating a long-distance flexible pipe. Concerning the gas/liquid/solid three-phase separator, a cyclone separator was developed, and improvement in lifting efficiency was confirmed. Helped by these, the problems of the gas lift system were almost solved, and a possibility of the commercial-base production system was obtained. 2 refs., 182 figs., 47 tabs.

Fiscal 2000 project for development of international standards for supporting novel industries. Standardization for securement of interconnection between intelligent home electric appliances; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo. Johokadenkiki kan no sogo setsuzokusei kakuho no tameno hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development had been under way since fiscal 1998 for working out propositions relating to the international standardization of connection interface systems for digital AV (audio-visual) equipment. This report outlines the result of the project in its fiscal last year. The link working group (WG) actually built a transceiver at 5 mm pitch in its second trial, measured and evaluated its behavior under high-temperature and high-humidity circumstances, and acquired numerical data for interface specifications. The connection interface WG in its second trial fabricated a tiny optical connector for POF (plastic optical fiber) and evaluated its resistance to environment. As the result, sufficient resistance to environment was detected in the connector, and then a proposition was presented to IEC/TC86 that the connector be standardized as an optical connector for intelligent home electric appliances. The POF optimization WG performed an environment resistant test for POF, similar to those for transceivers and connectors, and then recognized that POF of the GI type was low in transmission loss and that it stably retained its wide-band feature. (NEDO)

Joint research report of Central Research Institute of Electric Power Industry and Japan Research Institute Ltd. Conceptual construction of Japanese type end-use model; Denryoku chuo kenkyusho Nihon Sogo Kenkyusho kyodo kenkyu hokokusho. Nippon gata end use model no gainen kochiku

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-07-01

The concept of Japanese type demand analysis model (end-use model) was constructed for the efficient management of electric power companies and efficient power utilization. Diffusion and use conditions of domestic air conditioners are considerably different depending on local life style and climate. In order to design demand measures considering combination of appliances in every market segment, demands in an end use level (end demand level, each appliance level) should be acquired. The basic structure of the model is composed of various exogenous variables such as weather data, price and ups and downs trend of customers, and various appliance data such as size, efficiency and energy consumption rate, and various customer data such as possession rate of appliances and number of customers. The final energy demand is estimated by integrating the above variables. By systematizing the stored data of precise actual load conditions, construction of DSM (demand side management) strategy becomes possible by using computer tools. 8 refs., 15 figs., 13 tabs.

International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 1. Research study on integrated evaluation and development plan; Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 1. Sogo hyoka to kaihatsu keikaku no tame no chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This paper describes the research result on the WE-NET project in fiscal 1996. The WE-NET project is composed of various elemental technologies such as hydrogen production, transport, storage, low-temperature material, utilization and hydrogen combustion turbine. The organic integrated cooperation and coordination between individual subtasks are indispensable for effective promotion of the project and optimization of the total system. The current R and D states of every elemental technology were surveyed, and its findings were utilized for coordination of the whole project and examination of the research project including pilot studies. Eleven important items in the total coordination including a total system cost and safety measures in a developmental stage were examined. The development results for 4 years of fiscal 1993-1996 were assessed together, and the draft working plan for fiscal 1997-1998 was also decided. The verification test plan of a hydrogen combustion turbine scheduled in Phase II was studied, and the basic plans of development step were proposed. The draft report of a transition scenario was also prepared. 6 figs., 68 tabs.

Research report for fiscal 1998. Comprehensive research cooperation on environmental technologies (study of air pollution monitoring at model industrial estate in Thailand); 1998 nendo chosa hokokusho. Kankyo gijutsu sogo kenkyu kyoryoku (Taikoku model kogyo danchi taiki osen monitoring ni kansuru kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Cooperative studies are conducted for the improvement of technologies for preventing air pollution caused by SOx, NOx, volatile organic compounds, etc., discharged into the air by mills and factories. For the measurement of air pollution, instruments capable of automatic and uninterrupted measurement of SOx, NOx, and suspended particle matters are installed at Map Ta Phut Industrial Estate, and measurement is carried out. Volatile organic compounds are measured and analyzed along the borderline enclosing the estate. The amounts of SOx and NOx emitted by automobiles, ships, etc., are calculated. An air pollutant diffusion simulating model is built, into which data about pollution sources and weather are inputted for the calculation of SOx and NOx concentration levels at the industrial estate as is. Technologies are transferred to Thai researchers and engineers, which involve the use of instruments for the measurement of pollution levels in the environment and for the observation of weather conditions, the techniques of sampling and analysis, the construction of atmosphere simulating models, and the analysis and evaluation of the existing air pollution. (NEDO)

FY 1999 project on the development of new industry support type international standards. Comprehensive survey research on the promotion of international standardization; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Kokusai hyojunka suishin ni kakawaru sogo chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of promoting the international standardization effectively/strategically, a comprehensive survey was made, and the FY 1999 results were summarized. In the trend survey on the comprehensive international standardization, survey was conducted for companies in the material field (plastics, rubber and iron steel) and in the mechanical field (robot, machinery, aircraft, etc.). As a result of the survey, it was found out that they have few headquarters systems and experts, but they tackle it strategically and defensively, taking the standardization as business. Also as to the trend of CEN/CENELEC, importance of the continued trend survey was pointed out. In the survey of policy for the international standardization, survey was carried out on the trend of the process for working out the international standards (TS, ITS and SDO). Further, in relation to the technology standards and intellectual property rights in the hi-tech field, survey was made on the present situation of rules for handling intellectual property rights of organizations, groups, etc. for standardization, how to handle intellectual property rights in the standardization process, problems and the solution, etc. (NEDO)

Effects of variation of flow and accumulation of suspended solids on the performance of anaerobic/aerobic biofilm system applied to grey water treatment. kenkiter dot koki roshoho no shori seino ni oyobosu ryuryo hendo oyobi kendaku busshitsu no eikyo

Energy Technology Data Exchange (ETDEWEB)

Okubo, T; Sagehashi, M; Otsuka, N; Okada, M; Murakami, A [Tokyo University of Agriculture and Technology, Tokyo (Japan)

1991-04-10

In this study, effects of variation of flow and accumulation of suspended solids (SS) on the performance of anaerobic/aerobic biofilm system were investigated through the laboratory test using synthetic wastewater and the field test using grey water. Effects of flow variation scarcely appeared on the time change of effluent quality in both cases where daily average hydraulic retention time (HRT) in anaerobic filter was 20h and that of aerobic filter was 6.7h. In the field test, however, removal rate of organic substances was lower (20-30%) than that of the laboratory test (90%), since SS content in grey water accumulated in the anaerobic filter which led dissolution of organic substances from accumulated SS, blocking, and short-circuit flow. Moreover, it was confirmed by the batch test that constituent of grey water has lower resolution for microorganisms and is more difficult to nitrate than synthetic waste water. 24 refs., 11 figs., 4 tabs.

FY 2000 report on the investigation of environmental effects in the geothermal development promotion survey. Tertiary. No.B-7 Kuwanosawa area; 2000 nendo chinetsu kaihatsu sokushin chosa. Kankyo eikyo chosa hokokusho - No. B-7 Kuwanosawa chiiki (Dai 3 ji)

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-01-01

In the Kuwanosawa area, Yuzawa city, Akita prefecture, survey was conducted to grasp effects of drilling for structural boring in the geothermal survey on the peripheral environment. In the survey of animals, there were 5 orders/10 families/19 species of mammals and 10 orders/25 families/73 species of birds. Three kinds of precious animals were confirmed. There were 132 families/6,670 species in the flora. Three kinds of precious plants and three kinds of precious floras were confirmed. During the survey, drilling for structural boring was conducted. At three spas for survey, there were recognized some survey items of which there were great fluctuations. However, those are seasonal valuations or valuations related to the situation of the inside of hot springs. It is not recognized that the fluctuations were caused by the drilling work and pumping-up of geothermal water. The noise made during the well drilling was reduced around the well as theoretical values indicated. At a spot 200m away from the well, the noise was reduced from the environmental standard, and accordingly, it seems that there are few effects on the peripheral environment. The vibration was reduced around the well more than theoretical values indicated. That was below the control level at a spot 25m away from the well, and it seems that there are few effects on the peripheral environment. (NEDO)

Influence of ([alpha]+[beta]) STA and surface finishing on mechanical properties of Ti-6Al-4V alloy. Ti-6Al-4V gokin no kikaiteki seishitsu ni oyobosu taikichu ([alpha]+[beta])STA shori oyobi hyomen shiage no eikyo

Energy Technology Data Exchange (ETDEWEB)

Asami, K [Musashi Inst. of Tech., Tokyo (Japan); Hironaga, M [Musashi Inst. of Technology, Tokyo (Japan). Graduate Student

1992-10-15

Ti-6Al-4V allow was solution treated and aged (STA) in air, and the effect of degraded layer on static tensile properties and fatigue behavior was studied. Also, influence of surface finishing on fatigue strength was studied. Degraded layer formed with 0.75mm thick hardened layer has been formed below extremely thin TiO2 scale. Static tensile properties and fatigue behavior are not influenced by the hardened layer. The hardened layer formed below embrittle layer has smaller hadenening scale, and has shown no structural change with the core. Even for an embrittle layer of about 10[mu]m thickness, the ductility and fatigue strength have reduced significantly. The static strength has been improved about 20% with the complete removal of embrittle layer. The fatigue strength of the receiving material has been greater in the case of mechanical polished finishing using NO.1500 emery paper and diamond taste of 1[mu]m compared to electrical polishing. However, the fatigue strength has been lower in the case of mechanical polished STA material compared to electropolished material. 8 refs., 18 figs., 2 tabs.

Research report for fiscal 1998. Survey on the researchers and research institutes for the effects of global warming and its countermeasures; 1998 nendo onshitsu koka gas ni yoru kankyo eikyo nado ni kansuru kenkyusha kenkyu kikan chosa chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Researchers and research institutes across the world (except those in Japan), engaged in the study of global warming and measures to deal with the phenomenon, are extracted in compliance with certain specified standards, and the latest information on them is appropriately arranged and listed. It is further developed into an electronic database for the convenience of users. The collected information includes more than 230 research institutes and more than 1,000 researchers. The endeavor is exerted by extracting essays and institutes mainly out of the on-line databases. More than 1,000 essays and 130 institutes are covered. Visits are made to five institutes in the U.S. and four in Europe who are most actively engaged in the study of global warming, and detailed researches are conducted and information is exchanged. The Argonne National Institute copes with all energy problems related to global warming. Descriptions are given about environmental impact surveys and CO2 isolation in the ocean at the Center for Global Science of the Massachusetts Institute of Technology. At the Oak Ridge National Laboratory, the visitors heard explanations of technologies related to renewable energies and so forth. Researches are made into ecosystems at the University of California, and into natural energies at the University of Hawaii. Also visited are research institutes in Australia, Germany, Netherlands, and Britain. (NEDO)

Numerical simulation of growth of flames formed in two-dimensional mixing layer. 2nd Report. Effect of dilution of fuel; Nijigen kongo sonai ni keiseisareta kaen no seicho ni kansuru suchi simulation. 2. Nenryo no kishaku ni yoru eikyo

Energy Technology Data Exchange (ETDEWEB)

Noda, S [Toyohashi University of Technology, Aichi (Japan); Hashimoto, K [Sumitomo Metal Industries, Ltd., Osaka (Japan); Nakajima, T [Kobe University, Kobe (Japan). Faculty of Engineering

1994-07-25

The effect of fuel dilution on growth of flames formed in 2-D mixing layers was studied by numerical simulation. The methane mass fraction of fuel was adjusted to 1.0, 0.3 and 0.2 through dilution by nitrogen, while the oxygen mass fraction of an oxidizer was fixed at 0.27. Flame structure was complicated due to the flows separated by flame at the leading edge of flames, and three peaks of the second Damkohler number were observed. Fuel dilution by nitrogen caused blow-off of flames, and the mixing ratio of the fuel and oxidizer at the leading edge of flames was essential to blow-off of diffused flames. In the case where vortices were observed in a flow field, the first Damkohler number was important which was determined by the hydrodynamic characteristic time of coherent vortices and the chemical characteristic time of flame propagation based on the mixing ratio of the fuel and oxidizer at the leading edge of flames. The diffused flames were elongated by shearing force, and an exothermic reaction was suppressed and a flame stabilization decreased with a decrease in second Damkohler number. 10 refs., 9 figs., 1 tab.

Analysis of transient thermal behaviors during the charging process in stratified heat storage tanks. 2nd Report. Effects of characteristic parameters; Seiso chikunetsu sonai deno juten katei no kato netsuteki kyodo ni kansuru kaiseki. 2. Tokusei inshi no eikyo

Energy Technology Data Exchange (ETDEWEB)

Yoo, H; Hong, H; Pak, E

1997-11-25

The mixing effect deteriorates performance in a stratified heat storage tank. In the present study, the effect of characteristic factors during the charging process was analyzed, based on the analytical solution in the previous study in which a strict boundary condition was applied and a mixing effect was included. Also, the usefulness of the solution was verified and the method of application to a real system was examined by comparing it to other experimental results. It was concluded that the depth of the perfectly mixed region is dominant unless the Peclet number is very small. 10 refs., 8 figs.

Effect of volume change of coal during plastic and resolidifying phase on the internal gas pressure in coke ovens; Sekitan nanka saikoka katei ni okeru taiseki henka ga cokes ro no nanka yoyu sonai gas atsu ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Nomura, S; Arima, T [Nippon Steel Corp., Tokyo (Japan)

2000-08-01

The coking pressure in coke oven, which is caused by the internal gas pressure in the coal plastic layer, is determined by the gas permeability of the layer. The gas permeability of the plastic layer depends on its density as well as the physical property of the plastic coal itself The plastic layer is between the coke layer and the coal layer and the effect of the volume change of these outer layers, i.e. contraction and compression, on the density and the internal gas pressure of the plastic layer was studied. Sandwich carbonization test, where different coals were charged in the test coke oven, showed that the internal gas pressure in the plastic layer depends not only on the one kind of coal in plastic phase but also on the other kind of coal in resolidifying phase near the oven walls. The relative volume of coke transformed from the unit volume of coal was measured using X-ray CT scanner and it varied greatly across the coke oven width depending on the kinds of coals. The volume change of coal during plastic and resolidifying phase affects the density and the internal gas pressure of the plastic layer The relative volume of semicoke and coke transformed from the unit volume of coal near the oven walls is higher for a high coking pressure coal than that for a low coking pressure coal. This leads to the high density of the plastic layer and the generation of dangerously high internal gas pressure in the oven centre. (author)

Emission characteristics of premixed lean diesel combustion. Effects of injection nozzle and combustion chamber shape on combustion and emission characteristics; Kihaku yokongo diesel nensho no haishutsubutsu tokusei. Funmu keijo oyobi nenshoshitsu keijo ga haishutsu gas tokusei ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Harada, A; Sasaki, S; Miyamoto, T; Akagawa, H; Tsujimura, K

1997-10-01

Many articles about low NOx emission combustion are reported. A mixture formation is necessary to success low NOx emission combustion. But, there is few reports about the effect of nozzle and combustion shape on emissions which give influence on mixture. In this paper, the effects on characteristic of combustion and emissions of some land of injection nozzle and combustion chamber shape were investigated. As a result, it was cleared that the influence of combustion chamber shape on characteristic of combustion and emissions was varied by spray shape, and pintle type injection nozzle was suitable for PREDIC. 7 refs., 10 figs., 1 tab.

Fiscal 1999 achievement report on regional consortium research and development project. Regional consortium activity in its 2nd year (Research and development of hybrid-type biocompatible hard tissue replacing materials); 1999 nendo hybrid gata seitai yugo kinosei kososhiki daitai sozai seizo gijutsu no kenkyu kaihatsu seika hokokusho. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Studies are conducted about highly biocompatible {beta}-type titanium alloys and calcium phosphate-based ceramics, high in strength and low in elasticity and constituted of non-toxic alloy elements, and about the technology of providing coatings for these materials. In the designing of such a highly biocompatible titanium alloy and the evaluating of its mechanical properties, studies are conducted about alloy formation into a practical size, fatigue characteristics and micro-structure, methods for improving its wear resistance, etc. In the development of a melting/casting technique for this purpose, studies are conducted about the melting/casting of the alloy into a practical size and about a high-recision casting technology. In the research on biological evaluation of biocompatibility and on the technology of precision casting for dentistry, studies are conducted about the reaction of the alloy with biological tissues and methods for precision casting for dentistry. Studies are also conducted about the development of technologies for precision work and precision finish for alloys. Further studies involve the development of calcium phosphate-based ceramics for the enhancement of {beta}-type titanium alloy's biocompatibility and the establishment of a technology of providing coatings for the alloy. (NEDO)

FY1999 report of the research results of medical/engineering cooperative research project, fundamental research on diagnosis/treatment systems by imaging higher order information of living systems; 1999 nendo igaku kogaku renkeigata jigyo koji seitai joho no gazoka ni yoru shindan chiryo system ni kansuru kiban kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

The research and development efforts are made for the fundamental technology necessary for visualizing higher order information of the organs and tissues at high precision and non-invasively, and for supporting treatment of the malignant tumor and cerebrovascular diseases, while keeping the functions of the affected organs intact, and the FY 1999 results are reported. The program for the visualizing techniques includes designs of the pulse sequence for a 1H/13C-MRSI analyzer which observes proton and carbon by magnetic resonance spectrometric imaging (MRSI), and starts its programming. The program for the real-time analysis of tissue dynamics starts the designs of the coil for pelvis receiving the signals for monitoring dynamics of the abdominal organs at superhigh field. The program for systems for supporting treatment while keeping the functions of the affected organs intact starts development of the MR-matching heating system, for which the applications are designed, and measures against eddy current and resistance of the system as a whole to noise are studied. Development of the high-precision supersonic wave and far-infrared ray irradiation systems is started, in order to establish the treatment aided by radiant ray while keeping functions of the affected organs intact. (NEDO)

Hydroelastic responses of pontoon type very large floating offshore structures. 2nd Report. Effect of the water depth and the drift forces; Pontoon gata choogata futaishiki kaiyo kozobutsu no harochu chosei oto ni kansuru kenkyu. 2. Senkai eikyo to hyoryuryoku

Energy Technology Data Exchange (ETDEWEB)

Maeda, H; Miyajima, S [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science; Masuda, K; Ikoma, T [Nihon University, Tokyo (Japan). College of Science and Technology

1997-12-31

Steady-state drift force in regular waves is theoretically analyzed. It is also studied under combined external force experimentally using a two-dimensional water tank. The fluid forces are analyzed by the pressure distribution method based on the potential theory, in which the effects of water depth are taken into account to discuss the effects of elastic deformation of the floating structure on the drift characteristics of steady-state waves. The tests were carried out using a wave-making circulating water tank equipped with a wind duct to create wind, waves and tidal flow. Drift force under a combined external force by wind, wave and/or tidal flow cannot be accurately predicted by arithmetically adding these components. For predicting drift force by tidal flow, it is necessary to take into account drag force in current at the floating structure bottom as well as that in wind at the front face. Drift force by tidal flow is affected by shallowness of water, which should be taken into account for drag forces. The floating structure will be deformed along the wave face as its stiffness decreases, basically decreasing steady-state drift force. 9 refs., 14 figs.

Report on survey on geothermal development promotion in fiscal 1999. Report on survey on environmental effects - noise and vibration (No. B-5, Busadake Area); 1999 nendo chinetsu kaihatsu sokushin chosa. Kankyo eikyo chosa (soon shindo) hokokusho (No.B-5 Busadake chiiki)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Identification of noise and vibration levels and evaluation on environmental effects were performed in association with the excavation in the geothermal investigation well drilling point (well N11-MD-3) and the vicinity thereof in the Busadake area in Hokkaido. In the survey, noise and vibration were measured before and during the well excavation at the well drilling point and nearby four points (boundary of the drilling premises, 500-m point, Kawakita Spa and the entrance to the mountain stream of petroleum). In addition, a distance decay survey was carried out at five points in one direction from the well drilling point. The result of the noise measurement showed the value of about 30 to 50 dB before the well excavation at the drilling point and its vicinity, and about 40 to 60 dB during the excavation. The vibration was about 40 dB at the boundary of the premises during the excavation, whereas the places other than them showed the lower limit of measurement. In the distance decay of the noise, 75 dB at the 10-m point decayed to 50 dB or lower in the 200-m point, while the vibration level of 75 dB decayed to 30 dB or lower in the 100-m point. These facts lead to a conception that the noise and vibration in association with the well drilling would not give great influence on the neighboring environment. (NEDO)

Fatigue life estimation of welded joints of an aluminium alloy under superimposed random load waves (follow-up report). Effects of high frequency components; Jujo random kajuka ni okeru aluminium gokin yosetsu tsugite no hiro jumyo suitei (zokuho). Koshuha seibun no eikyo

Energy Technology Data Exchange (ETDEWEB)

Takahashi, I.; Maenaka, H.; Takada, A. [Ship Research Inst., Tokyo (Japan)

1996-12-31

In order to examine fatigue behavior of boxing welded joints of anticorrosion aluminum A 5083 P-O alloy, the residual stress measurements, static loading tests, elastic finite element analyses, constant amplitude fatigue tests, and random fatigue tests were conducted. For a load wave in the random loading fatigue tests, a direct current component, a zero-mean narrow band random process, and a high frequency component were combined and superimposed, to examine the effect of the high frequency component and the effect of the stress cycle count method and the mean stress correction on the life estimation. For the fatigue analysis, a reference stress, such as that considering the structural stress concentration, was proved effective in reducing the amount of scattering in the fatigue test results and in improving the life estimation accuracy. Accordingly, for the actual scale measurements, it is insufficient only to measure the stress at points far from the crack initiation place. It is required to analyze the fatigue by measuring the reference stress same as the basic data acquisition tests in the laboratory. 4 refs., 21 figs., 4 tabs.

Solid/liquid phase change heat transfer in porous media. Effect of density inversion of water on melting process in a rectangular region; Takoshitsu sonai no ko-ekiso henka. Mizu no mitsudo gyakuten ga kukei ryoiki no yukai katei ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Sasaguchi, K [Kumamoto University, Kumamoto (Japan). Faculty of Engineering

1994-12-25

Solid/liquid phase change in porous media has a wide relation with freezing and melting of ground bed, storage of cold heat in soil, and underground heat exchangers. This paper describes an investigation on the effect of density inversion on melting of ice in porous media by using the previously reported numerical analysis method. The high-temperature side temperature and the Darcy number were varied and investigated systematically on the ice in a porous media sealed in a rectangular container of which right hand side is maintained at elevated temperatures and the other three sides are insulated of heat. As a result, a large number of findings were obtained including the following matters: when the Darcy number is fixed at 4.01 {times} 10{sup {minus}5} and the high-temperature side temperature, Tw, is varied, the fluid descends along the high-temperature side because of the density inversion at Tw=4{degree}C, and forms one weak circulation that rotates clockwise; however, when the temperature reaches 16{degree}C, the circulation disappears, and a circulation rotating counterclockwise is observed, becoming identical to the case of a fluid where there is no density inversion; and change in the Nusselt number against the melting ratio, R, is the smallest at Tw=8{degree}C, and decreases monotonously with the R. 15 refs., 12 figs.

Study on closed pressure vessel test. Effect of heat rate, sample weight and vessel size on pressure rise due to thermal decomposition; Mippeigata atsuryoku yoki shiken ni kansuru kenkyu. Atsuryoku hassei kyodo ni oyobosu kanetsusokudo, shiryoryo oyobi youki saizu no eikyo

Energy Technology Data Exchange (ETDEWEB)

Aoki, Kenji.; Akutsu, Yoshiaki.; Arai, Mitsuru.; Tamura, Masamitsu. [The University of Tokyo, Tokyo (Japan). School of Engineering

1999-02-28

We have attempted to devise a new closed pressure vessel test apparatus in order to evaluate the violence of thermal decomposition of self-reactive materials and have examined some influencing factors, such as heat rate, sample weight, filling factor (sample weight/vessel size) and vessel size on Pmax (maximum pressure rise) and dP/dt (rate of pressure rise) due to their thermal decomposition. As a result, the following decreasing orders of Pmax and dP/dt were shown. Pmax: ADCA>BPZ>AIBN>TCP dP/dt: AIBN>BPZ>ADCA>TCP Moreover, Pmax was not almost influenced by heat rate, while dP/dt increased with an increase in heat rate in the case of BPZ. Pmax and dP/dt increased with an increase in sample weight and the degree of increase depended on the kinds of materials. In addition, it was shown that Pmax and dP/dt increased with an increase in vessel size at a constant filling factor. (author)

Hydroelastic responses of pontoon type very large floating offshore structures. 2nd Report. Effect of the water depth and the drift forces; Pontoon gata choogata futaishiki kaiyo kozobutsu no harochu chosei oto ni kansuru kenkyu. 2. Senkai eikyo to hyoryuryoku

Energy Technology Data Exchange (ETDEWEB)

Maeda, H.; Miyajima, S. [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science; Masuda, K.; Ikoma, T. [Nihon University, Tokyo (Japan). College of Science and Technology

1996-12-31

Steady-state drift force in regular waves is theoretically analyzed. It is also studied under combined external force experimentally using a two-dimensional water tank. The fluid forces are analyzed by the pressure distribution method based on the potential theory, in which the effects of water depth are taken into account to discuss the effects of elastic deformation of the floating structure on the drift characteristics of steady-state waves. The tests were carried out using a wave-making circulating water tank equipped with a wind duct to create wind, waves and tidal flow. Drift force under a combined external force by wind, wave and/or tidal flow cannot be accurately predicted by arithmetically adding these components. For predicting drift force by tidal flow, it is necessary to take into account drag force in current at the floating structure bottom as well as that in wind at the front face. Drift force by tidal flow is affected by shallowness of water, which should be taken into account for drag forces. The floating structure will be deformed along the wave face as its stiffness decreases, basically decreasing steady-state drift force. 9 refs., 14 figs.

Study on a constant-tip-speed-ratio operation of wind power generation system. Effect of load control system on dynamic behavior; Furyoku hatsuden system no hensoku seigyo unten ni kansuru kenkyu. Fuka seigyokei ga system no rikigakuteki kyodo ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Wakui, T.; Yamaguchi, K. [Waseda University, Tokyo (Japan); Tanzawa, Y. [Nippon Institute of Technology, Saitama (Japan); Hashizume, T.; Ota, E. [Waseda University, Tokyo (Japan). School of Science and Engineering

1998-06-01

The effect that the set data of the load control system in a wind power generation system exerts on the dynamic behavior of a system was investigated. The wind power generation system consists of a hybrid wind turbine with combined Darrieus and Savonius rotors, load with a generator and battery in the center, and a controller. A constant-tip-speed ratio operation that holds the circumferential speed ratio in which the power coefficient is maximized irrespective of the change in wind velocity was used to extract and convert the wind energy more effectively. In a high-wind velocity area, the system is operated at a fixed speed, and the increase in rotation is suppressed to protect the wing strength. In a large system, the response characteristics are only slightly improved by the limited load operation range and influenced rotor inertial. Power cannot be fully extracted even if the control system is changed in setting, and the applicability to the wind situation remains low. During the actual operation, the adjustment value of the control system should be set so that the output operation is satisfactorily possible in the specified load operation range, that is, the change in the instantaneous value of an effective power coefficient indicates almost flat gain characteristics in frequency characteristics. 14 refs., 10 figs., 2 tabs.

Fiscal 1999 survey for promotion of geothermal energy development. Survey report of environmental impact survey - Hot spring fluctuation (No. B-5, Musadake district); 1999 nendo chinetsu kaihatsu sokushin chosa. Kankyo eikyo chosa hokokusho (onsen hendo) (No.B-5 Musadake chiiki)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-12-01

Research boreholes N11-MD-3 and -4 were drilled in Shibetsu-cho, Shibetsu-gun, Hokkaido, in the period July 1999 through December 1999, and thermal water was examined at the sites in July and November 1999. For the purpose of detecting the impact of the said work on the environment, local hot springs were examined for their status before, during, and after the drilling period. Measurements were conducted in the period August 5, 1998, through December 31, 2000. It was found that no fluctuation in water temperature or yield attributable to the drilling was detected. Hot springs were examined for nine items including water temperature and pH level at four spots which were Kaiyo-dai, River Tenyu, and Otoko-yu and Onna-yu of Kawakita Hot Spring, when 23-31 measurements were performed from each of the four. (NEDO)

Fatigue life estimation of welded joints of an aluminium alloy under superimposed random load waves (follow-up report). Effects of high frequency components; Jujo random kajuka ni okeru aluminium gokin yosetsu tsugite no hiro jumyo suitei (zokuho). Koshuha seibun no eikyo

Energy Technology Data Exchange (ETDEWEB)

Takahashi, I; Maenaka, H; Takada, A [Ship Research Inst., Tokyo (Japan)

1997-12-31

In order to examine fatigue behavior of boxing welded joints of anticorrosion aluminum A 5083 P-O alloy, the residual stress measurements, static loading tests, elastic finite element analyses, constant amplitude fatigue tests, and random fatigue tests were conducted. For a load wave in the random loading fatigue tests, a direct current component, a zero-mean narrow band random process, and a high frequency component were combined and superimposed, to examine the effect of the high frequency component and the effect of the stress cycle count method and the mean stress correction on the life estimation. For the fatigue analysis, a reference stress, such as that considering the structural stress concentration, was proved effective in reducing the amount of scattering in the fatigue test results and in improving the life estimation accuracy. Accordingly, for the actual scale measurements, it is insufficient only to measure the stress at points far from the crack initiation place. It is required to analyze the fatigue by measuring the reference stress same as the basic data acquisition tests in the laboratory. 4 refs., 21 figs., 4 tabs.

FY 2000 report on the survey of the calculation of the overall conversion efficiency in case of using natural gas for fuel cells, etc.; 2000 nendo chosa hokokusho. Tennengas wo nenryodenchi ni mochiita baai no sogo henkan koritsu no santei ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of evaluating the efficiency of fuel cell including the fuel supply system, survey was made of drilling of gas resource, conversion to liquid base fuel, transportation, storage, etc., the energy conversion efficiency was studied considering reforming characteristics of various fuels. In the comparison between LNG, methanol, DME and GTL that originate in natural gas and LPG and naphtha that originate in oil, a big difference is that methanol, DME and GTL were made through the conversion process with the large energy consumption. Namely, by the time before the reforming into hydrogen, the oil base indicated a higher efficiency in secondary energy fuel production than the natural gas base. Further, the reforming efficiency is the highest in methanol and DME, and there is a little difference between the integrated fuel cell (normal pressure) and the hydrogen production use fuel cell (pressurized). Concerning city gas and GTL, the efficiency is lower, affected by S/C. The overall efficiency is determined considering the conversion efficiency in other stages since it is determined by the conversion efficiency of up to the raw fuel and the energy conversion efficiency at PEFC. (NEDO)

Project in fiscal 2000 of developing international standards for supporting new industries. Comprehensive surveys and researches in relation with promotion of international standardization; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Kokusai hyojunka suishin ni kakawaru sogo chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With an objective of promoting the international standardization efficiently and strategically, surveys were performed on trends of international standardization in Europe and America, and researches on means for the international standardization. The standards strategy in the U.S. is to increase the U.S. competitive power in overseas countries, support strongly the domestic markets, and at the same time, deal with problems such as those of the environment. It attempts to structure a framework that can be utilized by any concerned parties, including business entities, the government, and consumers, whereas the National Standards Strategy (NSS) has proposed the initiative. In Europe, targeting to establish international standards originated from Europe, works are becoming more active for new technologies such as information communicating technologies from the R and D phase to the test and evaluation methods, taking the standardization into consideration. These works are being carried out within the scope of the common EU R and D, represented by the 'Framework program' and the 'EUREKA program'. In the survey and research on means to complete the international standardization, analyses and surveys were performed on the latest information, such as TC/SC, which are scheduled of proposition. Advices were given on giving the directionality and establishing the strategy. (NEDO)

Report on the research and development achievements in fiscal 1999 on the international research cooperation project for comprehensive development and utilization technologies for gas hydrate resources; 1999 nendo gas hydrate shigen no energy sogo kaihatsu riyo gijutsu no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper reports the achievements in fiscal 1999 on development of gas hydrate resources. As a result of synthesizing gas hydrates in deposit systems, identifying stability zones in compositions, and studying thermal conductivity and dielectric constant of the deposits, the estimation accuracy has been enhanced steadily in estimating hydrate existing areas in actual frost areas. In the collecting technologies, a proposal was presented for a system by which carbon dioxide is introduced into ground beds at the same time as recovering gases, and gas hydrates are displaced with carbon dioxide hydrates. The displacement phenomenon was verified experimentally by controlling temperatures and pressures. Even below the freezing point, the production rate of the carbon dioxide hydrates is fast if it is above minus 4 degrees C. Salt diffusion behavior important in control of the production and decomposition, and action mechanisms of production and suppression agents were made clear microscopically. Experimental and theoretical discussions were given on dynamics of the production and decomposition. The cage occupation rate of methane hydrates was quantitatively measured successfully by using the Raman spectroscopy. Hydrates of gas mixture were utilized to have verified the possibility of separating the gas mixture constituents. (NEDO)

Fiscal 1998 intellectual infrastructure project utilizing civil sector functions. Research and development project on prompt-effect type intellectual infrastructure creation (Comprehensive survey); 1998 nendo minkan no kino wo katsuyoshita chiteki kiban jigyo seika hokokusho. Sokkogata chiteki kiban sosei kenkyu kaihatsu jigyo (sogo chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Surveys and studies were conducted to facilitate and invigorate research, development, and economic activities and to provide technology related intellectual assets in an organized, systematic way. In the survey related to the buildup of intellectual infrastructures, questionnaires were sent to 789 organizations in the industrial and academic domains concerning measuring standards, reference materials, base for information on biological resources, base for safety management of chemical substances, base relating to human life and welfare, and base of knowledge relating to materials. On-site surveys were also conducted in Asia, Australia, North America, and Europe. Concerning 10 inorganic reference solutions whose development is urged because they are related to environments, raw materials for them were selected, required purity levels were defined, and methods for measurement and evaluation of safety when in prolonged preservation were investigated. Conducted in the research and development of individual subjects were database buildup on thermophysical properties, research into long-term durability of heat-resistant composite materials, research into textural structure and characteristics as materials of sintered bodies of fine ceramics, database buildup on the safety of non-ferrous metals, studies of base of human characteristics measurement, and the like. (NEDO)

Fiscal 1997 R and D project under a consignment from NEDO. R and D of the femtosecond technology; 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Femto byo technology no kenkyu kaihatsu (femto byo technology no kenkyu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Ultrahigh-speed electronic technology is indispensable for creating industrial basic technologies supporting the advanced information society in the 21st century. Control technology of photonic and electronic states in a femtosecond region is essential. To establish the development policy of generation and transmission devices for femtosecond light pulses, research and analysis were made on nonlinear optical response and light pulse transmission properties. Basic issues on devices and materials such as mode-locked semiconductor laser, pulse compression device and light-light modulation material for coding were extracted. For new femtosecond light pulse control/distribution devices, research and analysis were made on response properties of intersubband transition phenomena in a semiconductor and electron spin relaxation phenomena, and semiconductor quantum structure. To develop metrological technology using ultra-short light pulse, study was made on an evaluation method for time- fluctuation of pulses in 100 femtosecond level. Generation of femtosecond high-intensity X-ray pulse was possible by fine control of the existing high-intensity laser. 19 refs., 26 figs., 1 tab.

Achievement report for fiscal 1999 on the development of total evaluation research laboratory system for the medical welfare equipment technology research and development project; 1999 nendo iryo fukushi kiki gijutsu kenkyu kaihatsu project yo sogo hyoka kenkyu rabo system kaihatsu jigyo seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

A laboratory system named above has been developed to propel forward efficiently the efforts to develop medical welfare technologies through close coordination between medicine and engineering. Six laboratories are linked with each other in a network for the realization of an environment in which general support is extended to all the stages of equipment development from basic through clinical assessment. The biomedical engineering laboratory is constituted of various analyzing devices, and is capable of in vitro assessment of bioingredients. The therapeutic laboratory is provided with bioinformation/NMR (nuclear magnetic resonance) measurement equipment, animal surgical operation equipment, etc., and performs the assessment of test animals at the first stage of clinical assessment. The diagnostic laboratory acquires various image data necessary for the development of medical equipment at the same level as that of the site of clinical diagnosis. The intelligent surgical operation room takes in real-time diagnostic images while a surgical operation is under way and, at the same time, assesses surgical devices in the same environment as that of the surgical operation room. The medical information laboratory accumulates medical and image data from the other laboratories, and integrates the accumulated data. The data management center manages the laboratories in a unified way and enables comprehensive assessment and research. (NEDO)

Project in fiscal 2000 of developing international standards for supporting new industries. Comprehensive surveys and researches in relation with promotion of international standardization; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Kokusai hyojunka suishin ni kakawaru sogo chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With an objective of promoting the international standardization efficiently and strategically, surveys were performed on trends of international standardization in Europe and America, and researches on means for the international standardization. The standards strategy in the U.S. is to increase the U.S. competitive power in overseas countries, support strongly the domestic markets, and at the same time, deal with problems such as those of the environment. It attempts to structure a framework that can be utilized by any concerned parties, including business entities, the government, and consumers, whereas the National Standards Strategy (NSS) has proposed the initiative. In Europe, targeting to establish international standards originated from Europe, works are becoming more active for new technologies such as information communicating technologies from the R and D phase to the test and evaluation methods, taking the standardization into consideration. These works are being carried out within the scope of the common EU R and D, represented by the 'Framework program' and the 'EUREKA program'. In the survey and research on means to complete the international standardization, analyses and surveys were performed on the latest information, such as TC/SC, which are scheduled of proposition. Advices were given on giving the directionality and establishing the strategy. (NEDO)

FY 1999 report on the results of the R and D project on the industrial technology for the global environment. R and D of the prediction technology of environmental effects brought by CO2 ocean sequestration (Development of prediction technology of environmental effects around the point of CO2 discharge and the research support survey); 1999 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo NEDO seika hokokusho. Nisankatanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu (CO2 horyuten shuhen'iki no kankyo eikyo yosoku gijutsu no kaihatsu narabini kenkyu shien chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of studying viability of CO2 ocean sequestration by discharging it at the intermediate depth of ocean, the R and D were conducted of 'prediction technology of environmental effects around the point of CO2 discharge,' and the FY 1999 results were summarized. In the study of elucidation of behavior of liquid CO2 at the time of discharge, melting speed of CO2 in water and seawater, 2D CO2 concentration distribution, etc. were measured using the circulation type deep-sea simulation experimental equipment. In the study of technology to send CO2 into the sea and dilute it, the process test using mock liquid was conducted. In the indoor experiment on CO2 effects on marine organisms, conducted were the detailed experiment on long-term effects of low concentration CO2 on sea urchins and shellfish, experiment on CO2 acute effects on eggs/fry and experiment on CO2 effects on adult fish. In the developmental study of the model to predict environmental effects around the point of CO2 discharge, carried out were the improvement of the model for prediction of effects on marine organisms, study of the CO2 diffusion in topographic features supposed to be Hawaii, etc. In the international joint study, measurement/observation technology, facilities, etc. were studied in preparation for the experiment actually conducted in the sea. (NEDO)

FY2000 report of the research results of medical/engineering cooperative research project, fundamental research on diagnosis/treatment systems by imaging higher order information of living systems; 2000 nendo igaku kogaku renkeigata kenkyu jigyo koji seitai joho no gazoka ni yoru shindan chiryo system ni kansuru kiban kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

The research and development efforts are made for the fundamental technology necessary for visualizing higher order information of the physiological functions of the organs and tissues at high precision and non-invasively, and for supporting treatment of the malignant tumor and cerebrovascular diseases, while keeping the functions of the affected organs intact, and the FY 2000 results are reported. The program for the visualizing techniques includes development of the pulse sequence for commercializing the proton and carbon magnetic resonance spectrometric imaging (MRSI), and development of the prototype 1H/13C-detecting circuit. The program for the real-time analysis of tissue dynamics includes production of cine-images of, e.g., the peristalsis of the uterus, to accumulate the basic data for monitoring dynamics of the abdominal organs. The program for systems for supporting treatment while keeping the functions of the affected organs intact includes the MR-aided temperature-sensing systems, and improvement of the techniques for correcting motion of the measured organs by extracting characteristic points in the images taken and of MR-aided temperature sensing accuracy. The program for radiotherapy and ultrasonic therapy of malignant tumors in the body stems includes development of high-accuracy irradiation system aided by real-time three-dimensional body motion monitoring system. (NEDO)

Relationship between concentration of surfactant and pressure for droplet creation, and effect on droplet size in microchannel O/W emulsification; Maikurochaneru ni yoru O/W nyukaho ni okeru kaimen kasseizai nodo to ekiteki seisei atsuryoku no kankei, oyobi koreraga ekitekikei ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Kawakatsu, T.; Komori, H.; Oda, N.; Yonemoto, T. [Tohoku Univ., Sendai (Japan). Graduate School of Engineering

1998-03-01

O/W (oil in water) emulsion is produced by micro-channel emulsification method, and the effects of surfactant concentration on the pressures at which droplet generation starts and stops are evaluated in connection with the water phase and oil phase interfacial tension. In addition, the effects of surfactant concentration and operational pressure on the droplet size are investigated by measuring the generated droplet distribution, mean droplet size, standard deviation, geometrical standard deviation, and the possibility of producing mono-dispersion emulsion whose droplet size is large than 10 micron. The breakthrough pressure and the minimum pressure for droplet generation become low with the increase of SDS (sodium lauryl sulfate) concentration. The surfactant concentration, however, is found to have no effect on the breakthrough pressure and the minimum pressure for droplet generation when the SDS concentration exceeds the critical micelle concentration. It is true also for a system added with NaCl. As regards droplet size, uniform 20{mu}m droplet is obtained irrespective of the surfactant concentration and pressure. 13 refs., 10 figs., 2 tabs.

Fiscal 2000 report on geothermal energy development promotion survey. Phase 1. Report on environmental impact survey in No. C-5 Appi district (Weather); 2000 nendo chinetsu kaihatsu sokushin chosa hokokusho. No.C-5. Appi chiiki - kankyo eikyo chosa (kisho) dai 1 ji

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

For grasping the characteristics of weather, climate, and natural earthquakes in and around the geothermal survey area in the Appi district, Iwate Prefecture, observation data of weather stations or the like in the neighborhood were collected and put in an easy-to-use order. Weather and earthquake data of the 1990-1999 decade were collected and subjected to statistical processing. Weather in the Appi District Survey C area is characterized in that it assumes the Japan Sea side pattern with much snow in winter and much rain in the rainy season. In the other seasons, however, it assumes the Pacific side inland pattern. Weather data in the Appi district and its vicinity are deemed to be similar to the values observed at the Hachimantai weather station. The area covered by the survey, however, is higher than the Hachimantai weather station by 400-900m, and therefore is that much colder and has more rain and snow. As for earthquakes, a total of 647 were recorded in the decade 1990-1999. In the Appi District Survey C area, which is approximately 20km times 20km large, suffered 31.1 events/month in 1998, which indicated a great rise in seismic occurrence. The rise is now attributed to the volcanic activity of Mt. Iwate which is deemed to be waning. (NEDO)

Thermal performance of a passive-designed dwelling unit. Annual thermal performance of two same-plan dwellings and influence of dwelling condition; Passive design sareta shugo jutaku no netsu seino ni kansuru kenkyu. Doitsu plan nijuko no nenkan netsuseino to lifestyle no eikyo

Energy Technology Data Exchange (ETDEWEB)

Sunaga, N; Muro, K [Tokyo Metropolitan University, Tokyo (Japan); Kamata, K [Housing and Urban Development Co., Tokyo (Japan)

1997-11-25

Measurements and analyses were made on two apartment houses which have attempted direct gain and natural ventilation. The measured houses are the houses A and B with total floor area of 130 m {sup 2}, respectively, in an apartment house of reinforced concrete structure, located in the southern area in Kanto Area. Sunlight is taken in from double glass windows in winter to store the heat in the reinforced concrete of the floor and rooms, while sunlight is shielded with the eaves and blinds in summer. The measurements were carried out on 16 points in every 30 minutes for one year. The result of the measurements may be summarized as follows: the indoor thermal environment in summer had the temperature varied between 24 and 34 degC because the air conditioner is used only infrequently; the house A attempts ventilation more positively than the house A, whereas the room temperature has become lower than 26 degC in about quarter of the whole measurement duration; and regarding the indoor thermal environment in winter, the house B had higher temperature in general, showing large variation with temperature exceeding 25 degC occasionally, which is thought because of difference in power consumption and ways of living in the building. 3 refs., 9 figs., 1 tab.

Image processing analysis of combustion for D. I. diesel engine with high pressure fuel injection. ; Effects of air swirl and injection pressure. Nensho shashin no gazo shori ni yoru koatsu funsha diesel kikan no nensho kaiseki. ; Swirl oyobi funsha atsuryoku no eikyo

Energy Technology Data Exchange (ETDEWEB)

Yamaguchi, I. (Japan Automobile Research Institute, Inc., Tsukuba (Japan)); Tsujimura, K.

1994-02-25

This paper reports an image processing analysis of combustion for a high-pressure direct injection diesel engine on the effects of air swirl and injection pressure upon combustion in the diesel engine. The paper summarizes a method to derive gas flow and turbulence strengths, and turbulent flow mixing velocity. The method derives these parameters by detecting movement of brightness unevenness on two flame photographs through utilizing the mutual correlative coefficients of image concentrations. Five types of combustion systems having different injection pressures, injection devices, and swirl ratios were used for the experiment. The result may be summarized as follows: variation in the average value of the turbulent flow mixing velocities due to difference in the swirl ratio is small in the initial phase of diffusion combustion; the difference is smaller in the case of high swirl ratio than in the case of low swirl ratio after the latter stage of the injection; the average value is larger with the higher the injection pressure during the initial stage of the combustion; after termination of the injection, the value is larger in the low pressure injection; and these trends agree with the trend in the time-based change in heat generation rates measured simultaneously. 6 refs., 14 figs., 2 tabs.

Effects of Al and Mn, alone and in combination, on growth and nutrient status of red pine seedlings hydroponically grown in nutrient culture solution; Suiko saibaishita akamatsunae no seicho oyobi eiyo jotai ni taisuru Al to Mn no tandoku oyobi fukugo eikyo

Energy Technology Data Exchange (ETDEWEB)

Lee, C.; Izuta, T.; Aoki, M.; Totsuka, T. [Tokyo University of Agriculture and Technology, Tokyo (Japan). Faculty of Agriculture

1997-09-10

Experiments have made clear the effects of Al and Mn on growth of red pine seedlings hydroponically grown. Analysis was performed on components of plants grown in culture solution into which Al and Mn were added alone or in combination. Photosynthesis velocity and dark respiration velocity of the seedlings were measured when they have fully grown. The following results were obtained: the Al addition reduces dry seedling weight, the T/R ratio (T is dry weight of a seedling above the ground and R is that under the ground) decreases as the addition amount is increased, and the photosynthesis velocity decreases; Al accumulates in roots reducing physiological function of the roots and concentrations of Ca and Mg; the dry weight decreases with increasing Mn addition, but does not affect the T/R ratio; the Mn addition reduces the photosynthesis velocity lowering chlorophyll content in needle leaves; the dark respiration velocity decreases as the Mn amount is increased, but does not affect that for trunks; Ca and Mg concentrations decrease in the trunks and roots; no significant compound effects of Al and Mn are recognized, and the effects are additive; and the concentration at which growth decrease appears is 10 ppm or higher for Al and 60 ppm or higher for Mn. 32 refs., 2 figs., 11 tabs.

Effects of melt-temperature on limiting current density in Al electrodeposition and morphology of Al electrodeposits obtained from ambient temperature type molten salt; Joongata yoyuen kara no denki aluminium mekki no genkai denryu mitsudo oyobi denseki keitai ni oyobosu mekki ekion no eikyo

Energy Technology Data Exchange (ETDEWEB)

Shimizu, T.; Tatano, M.; Uchida, Y. [Nisshin Steel Co. Ltd., Tokyo (Japan)

1996-03-31

Some of more important electrolytic solutions for Al electrodeposition are organic solvents, high-temperature type molten salts and low-temperature type molten salts having a melting point of 30{degree}C or lower, such as ethylmethylimidazolium chloride (EMIC). This study uses a molten salt of AlCl3-EMIC as the low-temperature type solution for high-speed electrodeposition. Discussed herein are the effects of melt temperature on limiting current density in Al electrodeposition and Al electrodeposit morphology. Limiting current density increases as melt temperature increases at any AlCl3 concentration used in this study. The AlCl3 concentration that gives the maximum limiting current density shifts from 64 to 67mol% at a melt temperature of 120{degree}C. A dense, smooth Al electrodeposited film results at a melt temperature of 100{degree}C or lower, but the electrodeposited grains become coarser as melt temperature increases. Melt temperature can be increased to 140{degree}C to secure a smooth electrodeposited film, showing possibility of 2 times faster electrodeposition than the conventional one. 21 refs., 12 figs., 1 tab.

Fiscal 1997 report on the results of the international standardization R and D. Measurement of ultra-micro chemical substances and measuring methods of hormone effects; 1997 nendo seika hokokusho kokusai hyojun soseigata kenkyu kaihatsu. Chobiryo kagaku busshitsu no keisoku horumon eikyo sayo sokuteiho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Concerning the measurement system of ultra-micro hazardous chemical substances in the global environment, the paper examined the present situation of chemical substances such as dioxins, made an experimental study on the method to analyze dioxins in exhaust gas from an aspect of international consistency, and worked out a JIS draft. As to the standard measuring method of hormone effects of chemical substances, the paper developed the competitive bonding experiment system to measure bonding ability of chemical substances to homo sapiens estrogen receptor (ER). By measuring ER bonding ability of 78 kinds of chemical substances, the measuring method was developed. In the development of the assay system for detection of hormone-like compounds, the assay system with transfer activity via estrogen receptor as an index was established using cultured cells and yeast. Further, the development was made of a measuring method of receptor bonding activity of hormone-like substances. 33 refs., 151 figs., 66 tabs.

Fiscal 1999 technical research report. Development project on prompt-effect international standards for developing new industry (Comprehensive survey and research concerning promotion of international standardization); 1999 nendo shinki sangyo ikusei sokkogata kokusai hyojun kaihatsu jigyo seika hokokusho. Kokusai hyojunka suishin ni kakawaru sogo chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For encouraging the promotion of international standardization involving the six subjects of advanced technology taken up under the above-named project, wide-range investigations are conducted into measures for international standardization, the activities of international standardizing agencies and organizations, and the approaches of European and American business corporations to this issue. Technical literature and material are studied in Japan, and interviews are held overseas with responsible persons at organizations and corporations engaged in this task. At Standards Development Organization (SDO) of America, verification tests are under way for early development into international standards of technical standards it has so far developed independently. For the strategical utilization of intellectual property incorporated into its technical standards, SDO accepts that the best policy is to win approvals from patent proprietors at the early stage of standardization process by presenting them with conditions about patent implementation. In Europe and America, for the enhancement of their competitive power in the international theater, governments and civil sectors cooperate with each other for the establishment of international standards and, in business corporations, the management takes the initiative in coping with the issue with an understanding that there are business opportunities in international standardization. (NEDO)

FY 1999 report on the results of the study of the generative utilization basement technology of environmental friendly type metal base materials. Element/comprehensive process study; 1999 nendo kankyo chowagata kinzokukei sozai kaisei riyo kiban gijutsu no kenkyu seika hokokusho. Yoso sogo process kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The R and D have been conducted since FY 1991 on the process in which scraps can be used with no reduction energy required in iron-making stage, and the results of FY 1999, the final fiscal year, were summarized. In the assessment study of the comprehensive system, a full scale of experiment was carried out of the experimental plant which was completed in March 1998. In this fiscal year, experiment was conducted on converter type and fixed bed type as preheating/melting method. As a result, the energy unit requirement, productivity, etc. which were targeted at first were obtained, and the experimental results expected at first were obtained on scrap preheating/melting technology/exhaust gas treatment. Moreover, the FS using the actual system was conducted, and the following conclusions were acquired: melting use primary energy decreased by more than 25% from that in the existing electric furnace; it is possible to arbitrarily select power loads at 80%-30% the same as those in the existing furnace; new melting method is more excellent in primary energy reduction than in advanced electric furnace as of FY 1999; it is possible to reduce primary energy by 25% also in the case of operating iron-melting in converter type and shaft type. (NEDO)

Fiscal 2000 project for development of international standards for supporting novel industries. Standardization for enhanced interoperability between optical disk systems; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Hikari disk system no sogo un'yosei kakuho no tame no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development was carried out for the enhancement of logical format-based interoperability between optical disk systems for the purpose of presenting propositions for international standards. That is, UDF (universal disk format) defined by OSTA (Optical Storage Technology Association) was taken up against the volume/file structure defined by ISO/IEC13346, and efforts were exerted to substantiate environments for its compatibility test and to develop specifications to achieve such enhanced interoperability. In this fiscal year, specifications were drafted for application program interfaces for the UDF-based file system and UDF security augmentation. These would be presented to IEC (International Electrotechnical Commission) and OSTA, respectively. Their Japanese versions were submitted to the Ministry of Economy, Trade and Industry of Japan, for publication as standard-related information. Maintenance of UAF (universal accessible file) system-compliance test tools were accomplished in response to user requirements and to the updating of UDF-compliance test disk specification. (NEDO)

Report on the research and development under a consignment from NEDO of high temperature carbon dioxide fixation and utilization technology for fiscal 1996; 1996 nendo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku gyomu seika hokokusho. Nisanka tanso koon bunri kaishu sairiyo gijutsu kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For the prevention of global warming, this R and D is aimed at separating/recovering high temperature CO2 from high temperature gas at 300degC or above and developing technology for effective use of the recovered CO2 as measures taken for reduction in CO2 emissions from the fixed emission sources. In this fiscal year, the following were proceeded with: heightening of separation performance evaluation technology, promotion of technical development of ceramic separation membranes and supports, and development of element technology of modular integration. In the examinational research on separation technology and system optimization, the following were conducted: survey of trends of the technical development, conceptual design of plant and prediction of process behavior, assessment of applicability of the process, and study of effects of utilization/spread of the developmental technology. In the former R and D, borosilicate glass powder rich in alkali is formed on the ring by joining the trially manufactured hollow fiber type membrane and the same form alumina cylinder, and sealing property and strength which stand measurement of permeability were confirmed. In the latter, an innovative process applied with CO2 high temperature separation technology was studied to examine effects of the spread of high temperature gas separation technology. 403 refs., 478 figs., 134 tabs.

FY 1999 project on the development of new industry support type international standards. Standardization for high-interoperability of optical disk systems; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Hikari disk system no sogo un'yosei kakuho no tame no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The R and D were conducted on the standardization for interoperability of optical disk system, and the FY 1999 results were summarized. In the study, for the volume/file structure specified by ISO/IEC 13346, the development of standards was made for interoperation of the UDF specified by OSTA. In this fiscal year, to avoid the problem on non-interchangeability of UDF which actually exists, enhancement of functions of a test tool for UDF interchangeability was tried. Namely, development was carried out of UDF interchangeability test tool, UAF related standards, and UAF related standards assessment system. Especially, it was formally announced that UDF security enhancement of UAF related standards will be included in UDF2.x in the OSTA conference held at the end of FY 1999. Also, a draft on the standard information was drawn up domestically. The standards including API are expected to be established as standards through activities in the next fiscal year. (NEDO)

FY 1999 project on the development of new industry support type international standards. Standardization for high-interoperability of optical disk systems; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Hikari disk system no sogo un'yosei kakuho no tame no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The R and D were conducted on the standardization for interoperability of optical disk system, and the FY 1999 results were summarized. In the study, for the volume/file structure specified by ISO/IEC 13346, the development of standards was made for interoperation of the UDF specified by OSTA. In this fiscal year, to avoid the problem on non-interchangeability of UDF which actually exists, enhancement of functions of a test tool for UDF interchangeability was tried. Namely, development was carried out of UDF interchangeability test tool, UAF related standards, and UAF related standards assessment system. Especially, it was formally announced that UDF security enhancement of UAF related standards will be included in UDF2.x in the OSTA conference held at the end of FY 1999. Also, a draft on the standard information was drawn up domestically. The standards including API are expected to be established as standards through activities in the next fiscal year. (NEDO)

FY 1999 project on the development of new industry support type international standards. Standardization for securing mutual connection among informative household electric appliances; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Joho kaden kikikan no sogo setsuzokusei kakuho no tame no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The R and D were conducted with the aim of the international standardization for securing mutual connection among informative household electric appliances, and the FY 1999 results were summarized. In FY 1999, the following were conducted: trial manufacture (for mass production) and evaluation of wide band POF (plastic optical fiber), trial manufacture and evaluation of home use small connector, and trial manufacture and evaluation of optical transceiver module. Various data required for the targeted standardization (transmission band: S400 or more, transmission distance: 100m) were obtained. In the next fiscal year, tests to demonstrate validity/reliability of the data are conducted so that the standards to be accepted as an international standard can be established. In the study of strategies of international standardization, the contents of the standards proposed were discussed, and activities of IEC/TC100 (multi-media) and the related TC were investigated. Early in the next fiscal year, the TC to be proposed is fixed, and international proposing activities are started such as the introduction of the standardization for this R and D to the organizations and persons concerned overseas. (NEDO)

FY 1997 report on the survey on the current residential waste treatment and integrated utilization of waste including heat supply in Shanghai city; 1997 nendo chosa hokokusho (Shanghai shi ni okeru seikatsu gomi shori no genjo narabini kyonetsunado wo fukumu sogo riyo ni kansuru chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Survey was made on residential waste treatment in Shanghai city. Shanghai city with nearly 13 million registered residents produces on average 10,000-11,000 tons/day residential solid wastes. Such wastes are basically disposed by land filling. A landfill site has a current disposal capacity of 7,500 tons/day, and is scheduled to be expanded up to 9,000 tons/day. Problems of waste disposal in Shanghai city are as follows: transportation of wastes collected in the city by trucks, transportation through transit stations to the landfill site by ships, and high disposal cost. Shanghai Environmental Sanitation Bureau is pursuing researches on recycling of wastes, reduction of wastes and harmless treatment in place of conventional land filling. As the survey result, adoption of complete separate collection of wastes is basically important, and application of the latest technologies such as combustion treatment for every waste, heat use, gasification fusion furnace, and RDF (refuse derived fuel) for coal-firing boilers should be considered. 86 figs., 18 tabs.

FY 1999 report on the comprehensive analysis of the geothermal development promotion survey. Forth. No.C-3 Akinomiya area (Separate volume 2: Collected data); 1999 nendo chinetsu kaihatsu sokushin chosa sogo kaiseki hokokusho. No. C-3 Akinomiya chiiki (Dai 4 ji) - Bessatsu 2 (shiryoshu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-01-01

As to the survey of the existence amount of geothermal resource in the Akinomiya area, Ogachi town, Akita prefecture, which was made in FY 1999, the comprehensive analysis was conducted, and the data were arranged. In relation to the surface survey, data on the following were described: geological survey, supplementary surface geological survey, soil gas survey, precision gravity survey, supplementary gravity survey and 3D model re-analysis, electromagnetic survey, etc. With relation to the well survey, data on the following: wells of N8-AY-1, N8-AY-2, N9-AY-3, N9-AY-4, N9-AY-5, N10-AY-6, N10-AY-7 and N10-AY-8, survey of cores of existing wells, temperature/pressure logging of wells remaining stationary after having been left long, sampler logging, etc. In relation to the jetting test, data on the short-term jetting test on wells of N8-AY-1, N8-AY-2, N9-AY-3, N9-AY-4, etc. With relation to the evaluation of reservoirs, data on the pressure monitoring, results of the reservoir simulation, etc. (NEDO)

FY 2000 Immediate-effect type project for research and development for international standards supporting information technology industries. Comprehensive study on promotion of international standardization; 2000 nendo joho sangyo shien sokkogata kokusai hyojun kaihatsu jigyo seika hokokusho. Kokusai hyojunka suishin ni kakawaru sogo chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The information technology and international standardization are studied for the elementary information technology, mechanical safety areas and electronic trading, aimed at achieving the international standards in a short time for the information industrial sector, which shows rapid technological development. The program for the elementary information technology includes development/standardization of the testing/evaluation methods for transparent electroconductive films for notebook computers, liquid crystal monitors or the like, specifically for the mechanical and physical properties. The program for mechanical safety areas includes definition of the closed space type mechanical safety monitoring techniques and use of safety-confirmation type sensors for the techniques, and standardization of the requirements of the protectors for use of the safety-confirmation type sensors, among others. The program for the electronic trading includes standardization of the electronic catalogues of the instrumentation devices, dictionaries of the instrumentation devices and device-screening processes. The other efforts include development of the applications and system infrastructure functions, construction of the demonstration test systems, and demonstration tests. (NEDO)

Report on a survey for promotion of geothermal development and an overall analysis of areas in fiscal 1996. Report No.C-3 for the Akinomiya area (First analysis); 1996 nendo chinetsu kaihatsu sokushin chosa sogo kaiseki hokokusho. No.C-3 (Akinomiya chiiki dai 1 ji)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-10-01

This paper summarizes the result of a survey for promotion of geothermal development and an overall analysis of the Akinomiya area in fiscal 1996. The subject area is located in Katsuo Town in south of Akita Prefecture. The geothermal reservoirs are regulated by the irregular construction created by upheaval and subsidence of the pre-Tertiary basement rocks. The underground temperature construction shows the temperatures rising toward Mt. Yamabushi. The latest geothermal activities should have taken place after the eruption of Mt. Takamatsu. The geothermal activities near the Arayu area have been most active until recently, and is still predominant. Transformation activities were active in the former period of the Pleistocene era. The acidic transformation band has been active after sedimentation of andesites in Mt. Takamatsu thereafter, which should have been active not only in areas where it is now active on the ground surface, but also in greatly wider areas. Geothermal fluid flows being regulated by faults, whereas fractures with high permeability existing along the faults are suitable for developing steam collection. Hot spring waters were produced by the geothermal fluid having risen along the faults and been mixed with and diluted by ground surface water near the ground surface. Areas promising for geothermal development would spread over the areas with high permeability along structural lines such as faults which show the convection type temperature pattern and temperatures higher than 250 degrees C. (NEDO)

Energy supply/demand structure development survey project / comprehensive survey on energy supply/demand development. FY1997 survey on techniques for pyroelectric power generation systems; Energy jukyu kozo kodoka chosa jigyo / energy jukyu kodoka sogo chosa. 1997 nendo shoden hatsuden system no gijutsu chosa seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-05-01

Pyroelectric conversion systems were surveyed as the techniques for effective utilization of low-temperature waste heat sources. Described herein are the principle of pyroelectric power generation, including pyroelectric phenomenon, origin of pyroelectricity in polymers, and pyroelectric polymers and copolymers; utilization of the pyroelectric phenomenon, including hysteresis of pyroelectric materials, general pyroelectric conversion principle, pyroelectric conversion cycle, analysis of power output by an Olsen cycle, comparison with a steam engine, and power outputting methods; pyroelectric conversion systems, including heat regeneration method, plate type pyroelectric conversion devices using the heat regeneration method, and voltage controlling methods; and pyroelectric conversion outputting, including calculations of power output and loss, conduction-caused loss, pumping loss, and pyroelectric converter efficiency. Other items described herein include conceptual designs of 1 and 100 kW pyroelectric converters for utilization of waste heat, and current status of pyroelectric converter development at CANMET Energy Technology Center. (NEDO)

FY 1999 cooperation program - Comprehensive research cooperation in environmental technology. Research cooperation in toxic/hazardous waste management in the Laguna de Bay region; 1999 nendo kenkyu kyoryoku jigyo. Kankyo gijutsu sogo kenkyu kyoryoku - Raguna ko chiiki ni okeru yudoku yugai haikibutsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of establishing preventive measures for water contamination in the Laguna de Bay region, the Philippines, where the water contamination is in progress and the eutrophication is feared, a research cooperation project was carried out on the water quality contamination monitoring technology (measuring method/analysis method/prediction method). In the survey of the state of generation of toxic/hazardous waste, the following were grasped based on the existing data: amount of use of toxic/hazardous substances in factories, state of generation of waste, situation of the processing/disposal, etc. In the detailed survey of the situation of pollution in the Laguna de Bay region, specimens of water quality and bottom material were collected from the lake and rivers thereinto, and qualitative/quantitative analysis of contaminants was made using atomic absorption spectrophotometer and gaschromatograph mass spectrometer. As to the evaluation of pollutant sources and control method, the paper conducted the introduction of measures generally taken against pollutant sources, study of a method to grasp the behavior of contaminants by the environmental assessment method for the closed water area, etc. The training was also conducted for researchers/engineers widely in charge of management of toxic/hazardous waste in the Philippines. (NEDO)

Fiscal 1997 report under consignment from NEDO on photon measuring/processing technology (development of power generation facility use high-function maintenance technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku photon keisoku kako gijutsu (hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

A research/development was conducted on technologies of photon applied measuring/photon applied processing/photon generation which are usable for heightening of reliability and maintenance efficiency of power generation facilities. In fiscal 1997, high melting-point metal particles were manufactured by high energy density laser for formation of high temperature and stabilized fine functional circuit. Further, a wavelength changeable ultra red laser light source was studied which can make in-situ measurement of gas concentration and components. A study was also made to examine the surface composition by measuring fluorescent X-rays emitted by radiating high intensity laser beam on the surface of material. A rod type and a slab type as a high-output complete-solidified laser are under development. There is also a development aiming at high speed/high quality photon processing such as high speed/high precision welding/cutting and laser joining. Besides, a study is being made of high energy pulse/high quality beam complete-solidified laser. The paper made a comprehensive survey of the trend of the photon measuring/monitoring technology, and made a systematical arrangement of the developmental subjects extracted. 142 refs., 357 figs., 62 tabs.

Fiscal 1996 report on the results of the R and D under a consignment from NEDO of environmental technology such as recycling (for public). 1; 1996 nendo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Recycle nado kankyo gijutsu kenkyu kaihatsu seika hokokusho (kokaiyo). 1

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This R and D is aimed at promoting reduction in environmental loads by waste, etc. and reutilization of waste, etc., and at developing environmental technology such as recycling contributing to reducing road traffic noise. Studies were made on operation conditions of material separation in the bottle state and flake state, color separation, washing process, etc. Moreover, tests were conducted on comparisons of performance of shredders with different functions. Running tests of 100,000 times were conducted to confirm effectiveness of durability of the paved road with used papers. Measurement of hardness of the resin using the sol-gel method and coating experiment using organic dye were carried out to study the membrane effect speed and flaw resistance of coating of coloring bottles. Gasification of shredder dust and separation of nonferrous metal and glass were conducted to get the basic data. As to FRP bath tubs, the ratio of glass fiber and plastics was studied and western tiles were trially manufactured. Further studies were made of removal conditions of noncombustibles, chlorine and sulfur content, and reaction conditions of alkali additives including kind, quantity and addition method. 166 figs., 132 tabs.

Effects of lactic acid bacteria in kimoto on sake brewing. Part 2. ; Promotion mechanism of enzymolysis in rice by teichoic acid. Kimotochu no nyusankin no seishu jozo ni oyobosu eikyo. 2. ; Kimotochu no nyusankin ni yuraisuru teikosan no. alpha. kamai yokai sokushin sayo kisaku

Energy Technology Data Exchange (ETDEWEB)

Mizoguchi, H.; Tsurumoto, M.; Furukawa, A.; Kawasaki, T. (Kikumasamune Sake Brewing Co. Ltd, Hyogo (Japan))

1991-07-25

In order to elucidate promotion mechanism of dissolution of {alpha}-rice (pregelatinized rice) by teichoic acid. adsorption of teichoic acid and {alpha}-amylase onto rice protein oryzenin was investigated by experiments. Teichoic acid was adsorbed well onto oryzenin and reduced adsorption of {alpha}-amylase. Adsorption of {alpha}-amylase onto rice powder was decreased logarithmically in proportion to the teichoic acid added. Both teichoic acid and {alpha}-amylase were adsorbed by histone, abundant in basic amino acids, and by anion-exchange resin. Adsorption of {alpha}-amylase onto them was reduced by coexistence with teichoic acid. As the results of experiments, it was inferred that teichoic acid became dissolvable through autolysis by lactic acid bacteria in kimoto, changed the state of electric charge on oryzenin surfaces through adsorption onto oryzenin by phosphoric group, decreasing adsorption of {alpha}-amylase onto oryzenin and increasing free {alpha}-amylase in the liquid phase, and thus increased the dissolution of {alpha}-rice. 9 refs., 6 figs., 3 tabs.

Desolvation of L-histidine and {alpha}-ketoisocaproic acid complex from ethanolate crystals under humidified conditions and influence of crystallinity on its desolvation; Histidine Ketoisocapron san ensan ethanol wamono kessho no koshitsudo jokenka deno datsu ethanol to datsu ethanol sei ni oyobosu kesshosei no eikyo

Energy Technology Data Exchange (ETDEWEB)

Kishimoto, S.; Tanabe, T.; Maruyama, S.; Kishishita, A.; Nagashima, N. [Ajinomoto Co. Inc., Tokyo (Japan)

1996-07-10

Desolvation of L-histidine and a-ketoisocaproic acid complex from ethanolate crystals was investigated. The ethanolate crystals were obtained from ethanol aqueous solutions of above 60 wt% of ethanol. It was difficult to remove ethanol molecules from the crystals lay vacuum drying. However, it was found that ethanol molecules in the crystal lattice could be released under humidified conditions, for example, 313 K and 60% relative humidity, accompanied by transformation to non-solvated crystals. When the peak of 2{theta}=9.0{degree}(CuK{alpha} radiation) in powder X-ray diffraction pattern of the ethanolate crystals was weak, ethanol molecules (about 1wt.%) remained in the crystals at the end of transformations and then the residual ethanol decreased slowly. A controlled moderate cooling process, where the supersaturation is released slowly, is the key point to obtain ethanolate crystals having high `crystallinity` (defined as peak height of 2{theta}=9.0{degree}) which shows quick desolation rather than adding ethanol for a rapid increase of supersaturation in crystallization. 6 refs., 7 figs.

Report on achievements in fiscal 1988 on research and development of the photoreactive materials under the next generation basic technology research and development project. Comprehensive surveys and researches on photoreactive materials; 1988 nendo hikari hanno zairyo no kenkyu kaihatsu seika hokokuksho. Hikari hanno zairyo sogo chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

This paper describes the achievements in fiscal 1988 on comprehensive surveys on photoreractive materials. Based on the research and development institution for the next generation basic technology under the initiative of the Agency of Industrial Science and Technology, development is being promoted on photoreactive materials, or photochromic materials and photochemical hole burning (PHB) materials (materials in which molecular structures and assembly state can be changed reversely by actions of light, leading to expectation of application thereof to ultra-high density recording, displays at high resolution, and light switches). In order to achieve smooth and efficient promotion of the development thereof, development of the related technologies inside and outside the country was surveyed and discussed. Comprehensive surveys and researches were also carried out on the common basic technologies by looking to the well-informed people for guidance on the research. This fiscal year has held joint committee meetings to which lecturers were invited to discuss respective problems in the research and development trends. In addition, as the domestic survey, the status of research and development at the Tsukuba University was surveyed on photo-responsive polymeric gels. Furthermore, as the survey on the overseas technological trends, information related to photoreactive materials was collected mainly on photochemical burning materials in the U.S.A., and the research trends were surveyed. (NEDO)

Fiscal 1997 report under consignment from NEDO on the R and D of femto-second technology (development of ultra short pulse optoelectronics technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku femto gyo technology no kenkyu kaihatsu (chotan pulse ko electronics gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Very high speed electronics technology is indispensable for the creation of industrial base technology which supports high grade informatizing in the 21st century. The state of light and electronics is controlled in the femto-second time domain. As to the development of femto-second light pulse generation/transmission technology, mode synchronous semiconductor laser was manufactured using the strain quantum well structure aiming at heightening profit, and the repeated frequency, 166GHz, was achieved. Relating to the pulse compression element, exciton photonic band was newly designed. A technology of coding was also studied. As to the development of technology of femto-second light pulse control/distribution, shortening of the wavelength down to 1.5{mu}m and a possibility of femto-second domain high speed response were indicated by the combined double quantum well structure. The quantitative measurement of spin relaxation characteristics was successfully made. By the Mach-Zehnder light switch, obtained was the world`s fastest light switching characteristic. To realize the femto-second class very high speed element, conditions were grasped on the crystal growth of Sb based ultra thin films operating in the 1.5{mu}m zone by studying the quantum well using transition among sub-bands. 242 refs., 280 figs., 12 tabs.

FY 1999 report on the comprehensive analysis of the geothermal development promotion survey. Forth. No.C-3 Akinomiya area (Separate volume 1: Forth survey); 1999 nendo chinetsu kaihatsu sokushin chosa sogo kaiseki hokokusho. No. C-3 Akinomiya chiiki (Dai 4 ji) - Bessatsu 1 (Dai 4 ji chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-01-01

The paper reported the results of the long-term jetting test, etc. which were carried out as the forth survey of the geothermal development promotion survey in the Akinomiya area, Ogachi town, Akita prefecture. The jetting induction and the situation of production/reduction were described as follows. N9-AY-3 began to well spontaneously after being induced by sending air up to wellhead pressure of 4.8 MpaG. Damping was recognized for a month or so after the start of jetting. After that, however, no damping was recognized, nor was recognized the deterioration of the fluid enthalpy with age. The pH of geothermal water was definite, approximately 8, and the electric conductivity and Cl concentration were 8,500 {mu}S/cm and 2,600 mg/L, respectively. The maximum jetting capacity of N10-AY-8 was 10.4t/h in steam and 8.9t/h in geothermal water at wellhead pressure of 0.24 MPaG, and after that, it showed a tendency to lower. The flow rate of reduction of N8-AY-1 changed from 80-90t/h at the beginning to 60-70t/h. With the continued reduction, the lowering of reduction capacity was recognized. In the test, the following were carried out: temperature/pressure/spinner logging, test on pressure transition, survey of fluid properties, survey of jetting microseisms, etc. (NEDO)

FY 1989 report on the results of the next generation industrial basement technology R and D project - R and D of photo-reactive materials. Comprehensive investigational research on photo-reactive materials; 1989 nendo hikari hanno zairyo no kenkyu kaihatsu seika hokokusho. Hikari hanno zairyo sogo chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-03-01

As to photochromic materials and photochemical hole burning (PHB) materials, for the purpose of smoothly/efficiently promoting the R and D, the common basic technology was comprehensively surveyed as well as survey/study of the related technology development in Japan and abroad. In FY 1889, a joint committee was held, and a meeting was held of lectures given by lecturers from outside on the following: reversible response LB multilayered film and 2D optical switching element, photochemical HB and solid polymer, photovoltaic excitation dynamics of polymer solid, wavelength variable/semiconducting laser, optical memory, etc. A meeting for study/discussion on the details was also held. Items for the meeting were as follows: optical orientation control of nematic liquid crystal by photochromic surface, design of photochromic molecules, molecular movement and photo-reactivity in molecular aggregation system matrices, PHB spectra and mesoscopic structure control, continuous HB using semiconducting laser and sub-picosecond photon echo, quinone system derivative PHB in polymer matrices, etc. (NEDO)

Report on the achievements in the Sunshine Project. A comprehensive report on development of coal liquefaction technologies and a performance test on Chinese coal liquefaction (fiscals 1981 through 1987); Sekitan ekika gijutsu kaihatsu seika hokokusho. Chugokutan ekika seino shiken sogo hokokusho (1981 nendo kara 1987 nendo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1988-03-01

The present Japan-China joint development project is intended to study liquefaction performance of different types of Chinese coals, select coal types suitable for coal liquefaction, and serve for enhancement in the coal liquefaction technologies employed by the Chinese side. Since a small continuous testing device has been installed in fiscal 1982 and begun with the trial operation in March 1983, the liquefaction test has been performed for about five years, and is scheduled to continue another three years. Chinese coals produced in seven provinces and two autonomous regions have been subjected to the coal type selection, on which discussions were given for liquefying reaction characteristics by using autoclave testing and small continuous testing devices. As a result, circulation tests were performed by the end of fiscal 1987 on five coal types, namely Beisu coal, Texgxian coal, Xianfeng coal, Shenmu coal, and Meihekou coal. Data were acquired during the circulation and at the equilibrium. Comparison of the results of tests on these five coal types with the results having been acquired from the 0.1-t/d BSU in Japan before modification verified the result being nearly reasonable. (NEDO)

Report for fiscal 1982 on comprehensive survey for nationwide geothermal resources. Preparation of basic map from among maps of nationwide geothermally promising areas (south Kyushu and north Kyushu); 1982 nendo zenkoku chinetsu shigen sogo chosa hokokusho. Zenkoku chinetsu yubo chiikizu no uchi motozu sakusei (Minaikyushu oyobi Kitakyushu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-03-01

With an objective to prepare the basic map from among maps of geothermally promising areas in the south Kyushu and north Kyushu, comprehensive analysis has been performed from the standpoint of geothermal analysis by combining the data derived from remote sensing with the data obtained by different physical exploration processes. The analysis has used mainly the gravity data, magnetism data, radar lineament, and Landsat lineament, as well as the latest data processing technology and analytical methods. As a result of the analysis, the area around Kirishima in south Kyushu was indicated as the most promising area for the future geothermal development. This area contains a series of new volcanoes, has the fault systems grown widely, and is expected of existence of water permeable reservoirs in deep underground. The Kagoshima bay area and the Sakurajima Island area were also regarded promising. In the north Kyushu area, such promising areas were indicated as the Futagoyama area in which highly magnetized and high-density volcanic rocks are recognized, and moreover, penetration rocks with magnetic anomaly are recognized in wide area, the area with volcanic actions from the Pliocene period to the Quarternary period, and the area at the north latitude of 33 degrees 38 minutes, and the east longitude of 131 degrees 02 minute. (NEDO)

FY 2000 report on the results of the project on the R and D of the global environmental industry technology. R and D of the technology for predicting environmental effects associated with the CO2 ocean sequestration (Development of the technology for predicting environmental effects in the area around the CO2 discharge point and survey for supporting study); 2000 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo. Nisanka tanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu (CO2 horyuten shuhen'iki no kankyo eikyo yosoku gijutsu no kaihatsu narabini kenkyu shien chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

To obtain the technical outlook for CO2 ocean sequestration by CO2 discharge into the intermediate layer, the R and D was conducted of the technology for predicting environmental effects in the area around the CO2 discharge point, and the FY 2000 results were summed up. In the elucidation study of the behavior at the time of discharging liquid CO2, the melting process of CO2 droplets discharged/dispersed into the seawater of the intermediate layer was observed, and the specific phenomenon of hydrate formation in the process of CO2 droplet formation was grasped. As to the technology for sending CO2 into the ocean and diluting it, experimental study was made of CO2 transportation technology from on the sea to the intermediate layer, technology for rapid dilution immediately after discharge, etc. About the indoor experiment on the CO2 influence on marine organisms, experiment on the CO2 influence was carried out using shells, sea urchin, red sea bream, etc. In the developmental study of models for predicting environmental effects in the area around the CO2 discharge point, the 3D two-phase flow LES model was developed as a model for predicting the CO2 behavior, and the simulation of the liquid CO2 discharge was made at the planned experimental site. The model for evaluation of the biological influence was also made which can consider the interaction between two kinds of organisms. (NEDO)

FY 1999 report on the results of the R and D project on the industrial technology for the global environment. R and D of the prediction technology of environmental effects brought by CO2 ocean sequestration (Development of prediction technology of environmental effects around the point of CO2 discharge and the research support survey); 1999 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo NEDO seika hokokusho. Nisankatanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu (CO2 horyuten shuhen'iki no kankyo eikyo yosoku gijutsu no kaihatsu narabini kenkyu shien chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of studying viability of CO2 ocean sequestration by discharging it at the intermediate depth of ocean, the R and D were conducted of 'prediction technology of environmental effects around the point of CO2 discharge,' and the FY 1999 results were summarized. In the study of elucidation of behavior of liquid CO2 at the time of discharge, melting speed of CO2 in water and seawater, 2D CO2 concentration distribution, etc. were measured using the circulation type deep-sea simulation experimental equipment. In the study of technology to send CO2 into the sea and dilute it, the process test using mock liquid was conducted. In the indoor experiment on CO2 effects on marine organisms, conducted were the detailed experiment on long-term effects of low concentration CO2 on sea urchins and shellfish, experiment on CO2 acute effects on eggs/fry and experiment on CO2 effects on adult fish. In the developmental study of the model to predict environmental effects around the point of CO2 discharge, carried out were the improvement of the model for prediction of effects on marine organisms, study of the CO2 diffusion in topographic features supposed to be Hawaii, etc. In the international joint study, measurement/observation technology, facilities, etc. were studied in preparation for the experiment actually conducted in the sea. (NEDO)

FY 2000 report on the results of the project on the R and D of the global environmental industry technology. R and D of the technology for predicting environmental effects associated with the CO2 ocean sequestration (Development of the technology for predicting environmental effects in the area around the CO2 discharge point and survey for supporting study); 2000 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo. Nisanka tanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu (CO2 horyuten shuhen'iki no kankyo eikyo yosoku gijutsu no kaihatsu narabini kenkyu shien chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

To obtain the technical outlook for CO2 ocean sequestration by CO2 discharge into the intermediate layer, the R and D was conducted of the technology for predicting environmental effects in the area around the CO2 discharge point, and the FY 2000 results were summed up. In the elucidation study of the behavior at the time of discharging liquid CO2, the melting process of CO2 droplets discharged/dispersed into the seawater of the intermediate layer was observed, and the specific phenomenon of hydrate formation in the process of CO2 droplet formation was grasped. As to the technology for sending CO2 into the ocean and diluting it, experimental study was made of CO2 transportation technology from on the sea to the intermediate layer, technology for rapid dilution immediately after discharge, etc. About the indoor experiment on the CO2 influence on marine organisms, experiment on the CO2 influence was carried out using shells, sea urchin, red sea bream, etc. In the developmental study of models for predicting environmental effects in the area around the CO2 discharge point, the 3D two-phase flow LES model was developed as a model for predicting the CO2 behavior, and the simulation of the liquid CO2 discharge was made at the planned experimental site. The model for evaluation of the biological influence was also made which can consider the interaction between two kinds of organisms. (NEDO)

Flow and mixing of gas in cylinder of a stratified charge engine with two intake valves. Effects of late closing valve timing and intake port configurations; Kyuki nibenshiki sojo kyuki engine no cylinder nai gas ryudo to kongo. Osotoji valve timing oyobi port keijo ni yoru eikyo

Energy Technology Data Exchange (ETDEWEB)

Charoenphonphanich, C; Niwa, H; Ennoji, H; Iijima, T [Tokai University, Tokyo (Japan)

1997-10-01

A numerical analysis of the flow and mixing of rich mixture and air inducted into the cylinder through each of the two intake ports of a stratified charge engine have been carried out. Numerical calculations were performed by finite volume method for three types of the intake port configurations: inverse V type, parallel type and V type and two types of valve timing; conventional and late closing (Miller cycle). Velocity field, turbulent kinetic energy and distribution of mixture concentration in the cylinder were examined. 3 refs., 10 figs.

Solidification of porous medium saturated with aqueous solution in a rectangular cell. ; Discussion on influence of initial concentration of solution and mean diameter of beads. Kukei sonai no suiyoeki de mitasareta takoshitsutai no gyoko. ; Shoki nodo to beads no heikin chokkei no eikyo ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Matsumoto, K [Miyazaki University, Miyazaki (Japan). Faculty of engineering; Okada, M [Aoyama Gakuin University, Tokyo (Japan). School of Science and Engineering; Murakami, M [Toshiba Corp., Tokyo (Japan); Yabushita, Y [Sony Corp., Tokyo (Japan)

1993-11-25

Studies have been made for the purpose of analyzing solidification phenomenon of ground in relation to freezing construction method used in subway, water supply, and sewage constructions. Experimental studies have been carried out on solidification process of porous medium saturated with aqueous solution to discover influence of initial concentration of the solution and diameter of beads that constitute a porous medium. The experiment was performed by solidifying the porous medium sequentially from a side wall with lower temperature in a rectangular experimental tank with a height and a width of 100 mm filled with NaCl aqueous solution and beads. As a result, it was discovered that, if the initial concentration is low, the temperature difference is little between the upper part and the lower part of the experimental tank, and natural convection in the liquid-phase region is suppressed because of rising solidification temperature; the natural convection is suppressed in the liquid-phase region; and the boundary face between the mushy region and the liquid-phase region moves quickly. Further, the concentration rise in the liquid-phase region has slowed down despite that the solidification region is large enough. The smaller the mean diameter of beads, the faster the growth rate on the boundary face, hence the natural convection in the tank has been suppressed, and the growth rate on the boundary face has increased. In addition, the concentration stratification in the liquid-phase region does not expand, but is formed only on the bottom. 6 refs., 12 figs.

Effects of elasticity on the damping characteristics of viscous shearing damper and estimation curve for modal damping in stay cables with this type of dampers. Cable seishin'yo nensei sendangata damper no gensui fuka tokusei ni oyobosu banegosei no eikyo to sono sekkeiyo gensui hyoka kyokusen

Energy Technology Data Exchange (ETDEWEB)

Yoneda, M. (Kawada Industries Inc., Tokyo (Japan)); Shimoda, I. (Oiles Corp., Tokyo (Japan))

1993-12-20

Oil dampers and viscous shearing dampers have been used to control wind-induced cable vibrations of cable-stayed bridges. The damping addition efficiency in the case where only damping force of the viscous shearing damper is considered was discussed in the previous paper. In this paper, more precise estimation is done by also considering the spring elasticity of the damper. Arranging the results of an indoor excitation test on viscous shearing dampers using SA-P viscous body, an experimental equation to express the spring rigidity is derived. The spring elasticity becomes smaller with increasing temperature of viscous body, decreasing frequency, and increasing amplitude. Then, the damping addition effect is measured by installing the viscous shearing damper on the actual bridge cable, and is compared with the theoretical value resulting from the complex-eigenvalue analysis. Consequently, it is shown that the theoretical value is almost correspondent with the measured result through the analysis using equivalent coefficient of viscosity and equivalent spring constant, which are arranged in the experimental equation. Moreover, application examples of damping estimation curves for designing cables with dampers are given. 15 refs., 13 figs., 10 tabs.

FY 1998 survey report. Survey on reduction in environmental effect of greenhouse effect gas by the transfer of environmental technology in the Asian region; 1998 nendo chosa hokokusho. Asia chiiki ni okeru kankyo gijutsu iten ni yoru onshitsu koka gas no kankyo eikyo keigen ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Effects of the transfer of environmental technology were studied as an important policy for control of greenhouse effect gas in the Asian region. As schemes, those that were drew up by NEDO, JICA, etc. now exist and are used also in Japan. However, for the control of greenhouse effect gas emission which is expected to rapidly increase in future, it is indispensable to construct a new powerful and effective scheme in which technology transfer and fund to be given are organically connected. Especially, in the U.S., etc., the assistance of developing countries of a huge amount of money such as Japan's ODA is not extended. However, they position the environmental technology as an important strategy and is developing the assistance of developing countries by technology transfer and eco-business of private companies. Also in the eco-business field, the environment-related technology of Japanese companies is used in Asian developing countries, with expectations of its being a new business with international competitive strength. This is the subject for the whole global environment, and an important subject also for Japan which requires the creation of a new business field with international competitive strength. (NEDO)

Report on the results of research and development under a consignment from NEDO on deca-nano quantum integrating transistor substrate technologies; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Deca-nano ryoshi shusekika soshi kiban gijutsu no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Researches have been conducted on deca-nano quantum integrating transistor substrate technologies, and developments were made on a three-dimensional device simulator which can be used in deca-nano domains, and a circuit simulator to have quantifying function transistors coexist with silicon semiconductor integrated circuits. The researches were intended to develop a simulator capable of analyzing properties of very small silicon and compound semiconductor devices in deca-nano domains. The researches discussed the applicability of conventional simulators, calculated quantum levels in a three-dimensional hetero structure, and resulted in development of an electron wave propagation simulator in optional two-dimensional shapes, a quantum Monte Carlo simulator, and a three-dimensional semiconductor device simulator with quantum correction. On the other hand, in order to estimate characteristics of a hybrid circuit in which single electron transistors coexist with conventional transistors such as CMOS transistors, a single electron hybrid circuit simulator was developed. The development indicated that a CMOS-SET fused memory is promising as a future LSI memory. 22 refs., 116 figs., 3 tabs.

FY 1991 report on the results of the surveys on the technologies for forming composite materials. Research and development of the new technologies for forming composite materials (Comprehensive surveys and researches); 1991 nendo fukugo zairyo seikei gijutsu chosa hokokusho. Fukugo zairyo shinseikei gijutsu no kenkyu kaihatsu (sogo chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-01

This project is aimed at development of new technologies for forming composite materials by studying the methods for controlling structures of ceramic- and metal-based composite materials, and also at development of the technologies for forming near-net shapes utilizing the phenomenon of superplasticity. The literature survey is conducted to help promote the developments, and the abstracts of the major papers are pigeonholed into 4 general categories; (1) production and properties of ceramic-based composite materials, (2) superplasticity of ceramic-based composite materials, (3) production and properties of metal-based composite materials, and (4) superplasticity of metal-based composite materials. This paper summarizes the abstract of these papers. The category (1) includes carbon fiber reinforced Sialon composites produced by polymer pyrolysis, the category (2) includes superplasticity of functional ceramics, and comparison of tensile and compressive creep behavior of a superplastic yttria-stabilized zirconia-20 wt.% alumina composite, the category (3) includes in-situ metal matrix composite, and the category (4) includes high strain rate superplasticity in whisker-reinforced alumina composites, and application of superplasticity to fabrication of metal matrix composites. (NEDO)

Report on the results of the fiscal 1997 R and D under consignment from NEDO of photon measuring/processing technology (development of high-efficiency production process technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku photon keisoku kako gijutsu (kokoritsu seisan process gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Development is made of high energy-efficiency laser processing technology and high efficiency/high grade photon generation/control technology as laser light source, for the purpose of energy conservation/efficiency heightening of production processes which require a large amount of energy such as welding, joining, surface treatment, and particle fabrication. As to keyhole dynamics of the molten metal generated on the laser weld, construction of simulational mathematical models was started. Equipment to fabricate semiconductor ultrafine particles which become the core of quantum dot functional structures was designed to fabricate particles. In-situ optical measuring technology was studied of element/size of particles of below 30 nm in size by emission spectroscopy associated with the plasma irradiation. As tightly focusing all-solid-state laser technology, studied was the wavelength conversion method in which harmonics are generated four times as much as the fundamental wave due to high efficient generation of high power UV laser. Also studied were high laser strength, low optical losses, conditions for fostering high homogenity crystals. Technology for high accuracy processing of element surface was established. High efficiency photon generation technology was comprehensively investigated. 140 refs., 276 figs., 46 tabs.

Fiscal 1996 report on the results of the R and D of technology of high-level treatment/effective use of domestic/industrial wastes, etc. (for public); 1996 nendo Shin Energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku seikatsu sangyo haikibutsu shori yuko riyo gijutsu kenkyu kaihatsu seika hokokusho (kokaiyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For the purpose of reducing environmental loads of waste and effectively using resource by waste recycling, a study was conducted of high-level treatment/effective use technology for domestic/industrial wastes, etc. The paper reported the results of fiscal 1996. In the EcoCement producing technology using the synthetic urban type waste, EcoCement with stable quality was obtained using sewage sludge and industrial waste as raw materials. In the specified freon decomposition disposal technology, an experiment was carried out on durability, etc. of the processing unit. In the high speed/reduced smell biological garbage disposal technology, technology of fermenting disposal, etc. were established, and at the same time technology of making garbage compost was developed. In the technology to manufacture environment friendly type plastic containers, etc., a degradation behavior was grasped of degradable plastics in the compost. In the spread type waste plastic/thermal recycle technology, studied were a system to collect waste and a system to make waste solid fuel. Technology to recycle coolant freon was studied. 14 refs., 261 figs., 137 tabs.

Fiscal 1997 research report on the R and D project under a consignment from NEDO. Photonics engineering (R and D of photonics measuring/processing technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Photon keisoku kako gijutsu (photon keisoku kako gijutsu no kenkyu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Survey was made on the trend of R and D on photonics engineering to clarify the direction of its impact and ripple effect on industrial fields. Reduction of environment burden, improvement of the productivity and reliability of products, and creation of new industries by novel creative R and D are necessary simultaneously. For reconsideration of the previous measurement and machining technologies in a manufacturing industry, use of photon (laser) beams is promising. As photonics engineering, photonics measurement and machining, and elemental and peripheral technologies for generation and control of photon were surveyed. Photonics application technologies for medical care and diagnosis, communication and transmission, entertainment, and chemical fields were also surveyed. In fiscal 1997 as the first year of this project, based on the results obtained in leading researches conducted until fiscal 1996, some technological issues were clarified through the survey on the latest trend of photonics engineering in measurement, machining and generation fields, and its feasibility in the other fields. 265 refs., 91 figs., 10 tabs.

Fiscal 1997 R and D project on industrial science technology under consignment from NEDO. Report on the R and D of nonlinear optoelectronic materials; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Hisenkei hikari denshi zairyo no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

As to the development of organic base materials, the paper is going ahead with an evaluation, higher performance and further use as materials of basic optical properties of quirale nonlinear materials and organic conjugate base materials which are promising among organic low molecular materials. As the development of orientation control crystal growth technology, grooves for orientation control were formed on the surface of the lead glass substrate, from which thin film single crystals were obtained. The nonlinear response was studied of the glass where semiconducting fine particles dispersed in matrix glass. Glass scattering base prototype materials were selected by the sol-gel method and ultra-low melting-point glass method. The glass dispersion base materials by the very fast cooling method was also studied. For the purpose of realizing a high speed switching characteristic, a processing technology was developed of ultra fine particle dispersing polymer light waveguide. As to the technology for super lattice, the optimum nonlinear performance materials were selected mainly with the optimum complex super lattice base. Moreover, the three-dimensional super structuring technology was constructed to improve nonlinear optical characteristics. The comprehensive investigational study was conducted for effective promotion of the research development. 177 refs., 260 figs., 27 tabs.

Report for fiscal 1981 on comprehensive survey for nationwide geothermal resources. Survey on radar imaging method - geothermal analysis conception design (Associated material 2 - reports on U.S. consultants); 1981 nendo zenkoku chinetsu shigen sogo chosa hokokusho. Radar eizoho chosa (chinetsu kaiseki gainen sekkei futai shiryo 2 (Beikoku consultant hokokusho))

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-10-01

Three technical and business proposals for comprehensive analysis of the survey data for nationwide geothermal resources in Japan were submitted from three U.S. candidate contractor groups, whose evaluations were reported by the Republic Geothermal, Inc. The group comprising of the Aero Service and Golder Associates has few geological engineers, and their engineers related to physical exploration has no experience whatsoever in the geothermal field. The group comprising of the EG and G Corporation, Geometrics, Utah University Research Institute, Mars, and Republic Geothermal, Inc. requires a maximum amount of time and travel expense to adjust the implementations done by four companies. However, this is a group having the largest pan-world geothermal experience, and much experience about Kyushu area of Japan. The group comprising of QEB, Inc., Eureka, and GSC, Inc. requires considerable amount of time and travel expense because of the implementation performed by three companies. The group has some geothermal experience in America, but none whatsoever in Japan. Holding or not holding persons with geothermal experience is an important criterion in selecting the contractors. (NEDO)

Fiscal 1998 regional consortium R and D project (Regional consortium field). Report on R and D of production technology of hybrid-type biocompatible hard tissue replacing materials (1st fiscal year); 1998 nendo chiiki konsoshiamu kenkyu kaihatsu jigyo. Chiiki konsoshiamu bun'ya (hybrid gata seitai yugo kinosei kososhiki daitai sozai seizo gijutsu no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This project aims at development of high-strength high- biocompatible {beta}-type Ti alloy with lower modulli of elasticity composed of non-toxic elements, phosphate calcium ceramics for improving the biocompatibility and coating technology, and establishment of production technology of hybrid-type biocompatible hard tissue replacing materials. In fiscal 1998, the project promoted the following: Design of high-biocompatible {beta}-type Ti alloy materials, development of thermomechanical treatment for improving dynamic characteristics of such alloy, survey on practical melting and casting technologies and dental precision casting process, evaluation of the biocompatibility of the alloy by cytotoxicity, selection of tools for precision machining and surface finishing, control of contents, orientation and precipitation of biocompatible crystals such as {beta}- Ca(PO{sub 3}){sub 2} fibers for further improvement of the biocompatibility. This paper also outlines the survey results on the market needs, market size and market share for the feasibility of these materials. (NEDO)

Report on achievements in fiscal 1999 on research and development of the glycocluster controlled biological molecule synthesizing under the industrial and scientific technology research and development theme [university collaborated type]. Bio-fiber manufacturing technology of glycocluster utilizing type; 1999 nendo glycocluster seigyo seitai bunshi gosei gijutsu seika hokokusho (glycocluster riyogata bio sen'i seizo gijutsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper describes the achievements in fiscal 1999 on development of the technology to manufacture glycocluster controlled biological molecules, particularly bio-fibers. It was made clear for the first time that the method for synthesizing glycoside and sugar chain using solid ultra-strong acid can be a new method for polysaccharide synthesis (polycondensation reaction) which is extremely simple and versatile as a result of using the solid ultra-strong acid. It can also be applied to general glycoside synthesis. In glycopeptide synthesis of the regular sequence type using high-functional condensation reaction, such a condensation agent as diphenyl phosphoryl azide was found effective in polymerization reaction without protection of glycopeptide, which has been impossible conventionally, and was found to have high versatility as a method for synthesizing mucin glycoproteins widely distributed naturally. In simplified synthesis of physiologically active glycopeptide, notice was given to tyrosine which is not glycosylated in the natural world, even though having hydroxyl groups in side chains as in serine and threonine. A method was established to introduce sugar chains into this hydroxyl group. This method exhibits power also in the synthesis of physiologically active glycopeptide of non-natural type. The paper describes also the comprehensive survey. (NEDO)

Fiscal 2000 project of inviting proposals for international joint research - invitation for international proposal (Novel No.2). Achievement report on development of high-strength ultralight biocompatible implant material using porous titanium; 2000 nendo kokusai kyodo kenkyu teian kobo jigyo - kokusai teian kobo (shinki No.2). Takoshitsu chitan ni yoru seitai shinwasei kokyodo chokeiryo implant zai no kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

An implant material manufacturing technology is developed for which a titanium based metal material is made porous and osteoblasts are allowed into holes in the material surface for the establishment of fixation and mechanical similarity between the material and bones. Activities are conducted in the six fields of (1) the establishment of material adjusting technology, (2) establishment of high-porosity sintering technology, (3) research and development of hydrogen-aided technology of pore formation, (4) improvement on mechanical characteristics/dimensions evaluation technology, (5) establishment and implementation of biocompatibility evaluation technology, and (6) the development of technology for commercializing high-porosity implant materials. In field (3), pure titanium and titanium hydride are pulverized and classified, and very fine powders only are mixed and sealed into a capsule made of pure iron, which is subjected to extrusion into bulk and then heated to a high temperature for the generation of hydrogen gas for the formation of a limitless number of pores. Pure titanium and a Ti-Al-V-Mo-Fe alloy easy to treat in a low-temperature superplastic process are used for the study of the process. In field (6), in the wake of element technology development, commercialization of implant materials is considered, technical tasks to discharge before new industry creation are made clear, and measures in this connection are studied. (NEDO)

Fiscal 1998 achievement report on regional consortium research and development project. Regional consortium of venture business fostering type--Creation of key industries (Development of technologies for manufacturing and utilizing various biological regulatory substances using Hokkaido-produced biomasses as materials); 1998 nendo Dosan biomass wo genryo to shita kakushu seitai chosetsu kino busshitsu no seisan riyo gijutsu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The efforts aim to meet consumers' needs for products that will prevent lifestyle diseases or the like. For this purpose, substances answering the purpose are extracted from Hokkaido-produced agricultural and aquatic biomasses, and prepared for testing. Researches are conducted on how they behave in the enzyme, cell, and biological systems, and active substances are isolated and identified. In relation to the aquatic biomass, a technology is established of extracting and separating DHA (docosahexaenoic acid), EPA (eicosapentaenoic acid), taurine, etc., which are multivalent unsaturated fatty acids effective in preventing lifestyle diseases, from the unused parts of the squid. In relation to the agricultural biomass, antimicrobial active substances are extracted and separated from small fruit plants such as the chicory. Long-keeping foods are tentatively produced by the addition of dried powder of the chicory root tuber. In the elucidation of various biological regulatory substances contained in the Hokkaido-produced biomasses, they are tested for their abilities to resist microbes and active oxygen. Furthermore, verification tests are conducted by administering the substances to the senescence-accelerated mouse (SAM). (NEDO)

Report on surveys in fiscal 1999 on technological trends in overseas countries in research and development of the technology to create biological bonding substances utilizing particulates under the industrial and scientific technology research and development theme (university collaborated type); 1999 nendo biryushi riyogata seitai ketsugo busshitsu nado sosei gijutsu no kenkyu kaihatsu kaigai gijutsu doko chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper describes the surveys in fiscal 1999 on technological trends in overseas countries in research and development of the technology to create biological bonding substances utilizing particulates. Attendance was made at the U.S. Biochemistry and Molecular Biology '99 to survey signal transmission in cells, new molecules related to gene transcription control, and the mechanisms thereof. A visit was made to the U.S.A. to collect the chromatin research information. In order to analyze efficiently specific biological receptors relative chemical substances, and structure an activity evaluation system, attendance was made at a society meeting in Britain to incorporate the high throughput screening technology. Attendance was made at a publication meeting in the U.S.A. to understand the current status of the DNA micro-array process. Visits were made to American business entities and societies to survey information that contributes to efficient separation and analysis of biological receptors. American business entities and universities were visited to survey the cDNA manifestation library system, technological trends, and researches on intra-living organism systems by using molecular biology. Visits were made to research institutes and societies in the U.S.A. to survey the method for carrying ligands onto latex beads, combinatorial chemistry, and solid phase synthesis. (NEDO)

Properties of P/M forged Al-Si alloys made by premixed powders. 1. Influences of dispersion and sizes of proeutectic Si on wear resistance; Kongoho ni yotte sakuseishita Al-Si kei shoketsu tanzo gokin no tokusei. 1. Taimamosei ni oyobosu shosho Si no bunsan jotai to ryukei no eikyo

Energy Technology Data Exchange (ETDEWEB)

Ishijima, Z.; Ichikawa, J.; Sasaki, s.; Shikata, H. [Hitachi Powdered Metals Co. Ltd., Tokyo (Japan)

1995-10-15

Influences of dispersion and sizes of proeutectic Si on wear resistance of P/M Al-Si alloys using the prealloying method and premixing method have been investigated. As a result, discretely dispersed proeutectic Si showed excellent wear resistance in compassion with uniformly dispersed one. The cause is considered to be the unclosed Si soft phase which has been preferentially worn away, consequently acting on forming oil grooves and burying worn particles. Further more the existence of the optimum size of proeutectic Si on wear resistance was confirmed. In the case of finer particles, only Al-Si alloy (pin) was warned away substantially. On the other handgun the case of larger particles, both the Al-Si alloy (pin) and the mating malarial (steel disc) were excessively warned away. It is assumed therefore that the finer proeutectic Si particles are not effective as hard particles, on the contrary, larger proeutectic Si particles increase the abrasive wear against the mating material, and those buried into the mating material initiate wear of Al-Si alloy at the same time. 2 refs., 10 figs., 1 tab.

Report on achievements of research and development of a technology to apply human senses to measurements in fiscal 1993. 2. Research and development of physiological effect measuring technology (Part 1); 1993 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu. 2. Seiriteki eikyo keisoku gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Development in fiscal 1993 of a composite physiological function measurement method to measure stresses included the development of a watch type device using the tri-electrode double-point simultaneous measuring method for skin impedance, and a device placed around a head as a blinking meter using the simplified potential method. Both were reduced largely in size and weight. They were verified to have good performance by the measurement performance experiments. For noncontact skin temperature measurement, a noncontact temperature measuring system will be developed that automatically tracks movement of the head of a human body which moves within a limited area, and continuously measure temperatures of specific positions with measurement resolution of 0.2 degree C. Image processing utilizing sensor fusion of infrared and visible images was used to have extracted successfully persons under the natural background. A technology was developed to recognize specific portions of a face (eyes and eyebrows). Developments were made on an algorithm to measure directions of a head, and an attitude controlling and measuring system using a magnetic sensor. In measuring stress index materials, a prospect was obtained to realize semi-macro measurement by collecting cortisol and catecholamine from saliva. Discussions were also given on detecting catecholamine in urine by using high-speed liquid chromatography. (NEDO)

Emission behaviors of nitrous oxide from automobiles. 4th Report. Aging effect of three way catalyst on N2O mass emissions; Jidosha kara haishutsusareru asanka chisso (N2O) no haishutsu kyodo ni kansuru kenkyu. 4. Sangen shokubai no rekka ga N2O haishutsuryo ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Koike, N; Suzuki, H; Odaka, M [Traffic Safety and Nuisance Research Institute, Tokyo (Japan)

1997-10-01

Several kind of three way catalysts with different metal compositions have been developed for trial and their N2O formation behaviors before and after the durability tests have been observed. Then by comparing the N2O formation behavior between new and durability tested catalysts, N2O increase mechanism with aging has been experimentally analyzed. As results, A catalyst temperature at peak N2O formation will sift to higher side by the aging and enters in the range that is the higher percentage in use during test cycle driving. Then this is the main cause of increase in total N2O emission. 4 refs., 10 figs., 2 tabs.

Report on achievements of research and development of a technology to apply human senses to measurements in fiscal 1992. 2. Research and development of a physiological effect measuring technology (Part 1); 1992 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu. 2. Seiriteki eikyo keisoku gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

This paper describes the physiological effect measuring technology, extracted from the achievements in the development of a technology to apply human senses to measurements in fiscal 1992. In the composite physiological function measuring technology to measure stresses, improvement was made on the skin impedance measuring device of tri-electrode double-point simultaneous measuring type. A non-contact measuring device using a light sensor was developed as a spontaneous blinking detecting system. A prototype device that can measure blood pressure continuously at the temple was developed, and its usefulness was verified. In non-contact skin temperature measurement, expansion was performed on the image input type visible camera, infrared ray camera and other systems produced to date, and hardware structuring was completed. For the software, person extracting, position recognizing and attitude determining algorithms were developed, whose effectiveness was verified experimentally. A prospect was reached that in measuring stress indexing substances, the measurement can be performed non-invasively using small amount of saliva and urine. The sensitivity was enhanced 20 to 5000 times in catecholamine, and ten times in corticosteroid as much as that in the previous year. It is estimated that on-line measurement may be executed on cortisol by using saliva sample of 100 to 200 {mu} L. (NEDO)

Report on achievements of research and development of a technology to apply human senses to measurements in fiscal 1993. 2. Research and development of physiological effect measuring technology (Part 2); 1993 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu. 2. Seiriteki eikyo keisoku gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

The high-sensitivity brain wave measuring device has been given improvements in the simplified device net type brain wave sensor that has been improved in fiscal 1993, eliminating the steamy feeling in the head, giving better fitting feeling, and having cleared the target. The multiple application telemeter had the stability enhanced, making it possible to measure living organism signals such as electromyogram, electrocardiogram, eyeball movements, and respiration. To measure living organism activity and rhythm, development was made on a method to evaluate these subjects by using substitution characteristics with development of a portable monitor kept in mind. Measurement and evaluation methods were prepared on the living organism activity from the comparison of the autonomic nervous system activity derived from continuous measurement of pulse cycles with the change in spectra in the {alpha} brain wave. An intestinum rectum temperature correction filter using the number of pulses was fabricated to introduce a body temperature rhythm curve excluded of effects of the body activity. The living organism activity was evaluated comprehensively from the contrast between the daily activity variation and the circadian rhythm. Improvement of accuracy of the tympanum temperature sensor was also discussed. In developing the accelerated pulse meter, the size of the transmitter was reduced, a filter was developed to reduce obstruction signals contained in the signals, and development was begun on a personal computer based system. (NEDO)

Report on achievements of research and development of a technology to apply human senses to measurements in fiscal 1992. 2. Research and development of a physiological effect measuring technology (Part 2); 1992 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu. 2. Seiriteki eikyo keisoku gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

This paper describes the physiological effect measuring technology, extracted from the achievements in the development of a technology to apply human senses to measurements in fiscal 1992. Primary prototype fabrication and evaluation were given on an easy-to-mount high-sensitivity brain wave measuring instrument. The multiple application telemeter has come close to completion excepting the integration. For multi-point brain wave measurement, analyzing device interface was completed. In measuring living organism activity and rhythm, development was made on an evaluation method that uses substituting characteristics, with a portable monitor kept in mind. The activity generated by power spectrum change in the {alpha} brain wave was compared with that in the autonomic nervous system to derive the mutual relationship therein, whereas usefulness of the pulse cycle characteristics was verified. Development was made on a method to measure and analyze the tympanum temperature rhythm that corresponds to the intestinum rectum rhythm, and the tympanum temperature was measured discretely by using an infrared sensor. Verification was given on the correlation between the circadian rhythm derived from the intestinum rectum temperature and that derived from the discrete measurement. In developing a nonrestraind accelerated pulse meter, a transmitter of the small accelerated pulse meter that can measure pulses under non-invasive and nonrestraint condition was fabricated on a trial basis, whose easiness of mounting and possibility of signal transmission were demonstrated. (NEDO)

FY 1996 R/D project of industrial and scientific technologies contracted with NEDO. Report on R/D of organosilicon polymers; 1996 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (Keisokei kobunshi zairyo no kenkyu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-01

Organosilicon polymers are highly innovative materials having high performance and novel functions, and they can be widely applied. The purpose of this study is to establish fundamental techniques for molecular design, synthesis, material processing and evaluation of organosilicon polymers having excellent electro- and photo-functions, and advanced heat-proof, fire-proof and mechanical properties. This R/D includes (1) R/D of electrical conducting materials by organosilicon polymers, (2) R/D of novel organosilicon polymers applicable to direct lithography, (3) R/D of new silicon-based polymer materials with electro-luminous function, and (4) R/D of silicon-based polymers for new photoconductive materials. In (1), synthesis of highly conjugated polymers is investigated. In (2), novel organosilicon polymeric materials have been developed, which would be applicable to direct lithography of electronic circuits, and which could contribute to simplification of the circuit formation process. In (3), the research aims at development of new silicon-based polymer materials with luminescent function which can be applied to the large size electro-luminescent display devices. In (4), new materials with visible light absorption have been synthesized through the molecular design and synthesis. The photo-carrier generation was observed. 107 refs., 86 figs., 23 tabs.

Fiscal 1997 report on the results of the technical development of super metal under consignment from NEDO. Technology to create ferrous mesoscopic structure control materials; Super metal no gijutsu kaihatsu (tetsukei mesoscopic soshiki seigyo zairyo sosei gijutsu) seika hokokusho (1997 nendo). Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko (NEDO) itaku kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The fiscal 1997 results were reported of the project on the technical development of super metal which draws out limit performance of ferrous metal and improves the recyclability. In the study of large-strain deformation, a study was carried out with the use of large-strain deformation of more than 50% per 1 pass (strain rate: 0.7 or more) and multi-phase structure. By the crystal microstructuring technology, a level was reached where approximately 1{mu}m crystal size can be obtained. In the study of high magnetic field utilization, the course of study of the structure control and microstructuring was chosen in the preliminary experiment using the existing 8 tesla magnet, and the design and fabrication of a new 12 tesla large-diameter magnet were conducted. In the study of material structure prediction, modeling of microstructuring by recrystallization and establishment of a material predicting method of micro/multi-phase/mixed-grain structures were made the subjects. In the analysis of the mesoscopic structure, the mesoscopic analysis was made of the 0.3C-9Ni steel microstructured by the large-strain deformation thermal processing, and it was shown that the reflective electronic image measured by varying accelerating voltage gives new structural information. 111 refs., 135 figs., 35 tabs.

Report on the results of the FY 1998 hydrogen utilization international clean energy system technology (WE-NET). Subtask 1. Survey/research for the comprehensive evaluation and developmental plan; 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET). 1. Sogo hyoka to kaihatsu keikaku no tame no chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The paper described the results of the FY 1998 WE-NET project survey. WE-NET is composed of various element technologies such as hydrogen production, hydrogen transportation, storage technology, low-temperature materials, hydrogen utilization, and hydrogen combustion turbine technology. Therefore, considering the effectiveness as a total system, it is extremely important to traversally evaluate the situation of the R and D of each technology and developmental achievements and to work out developmental plans with integration, considering the effectiveness as a total system. From viewpoints of making effective promotion of the project and attempting optimization as a total system, it is necessary to make organic/comprehensive connection and adjustment among individual subtasks all the time. In this survey/research, in the case of proceeding with the above-mentioned studies, a committee having knowledgeable persons and learned persons as members was established. There, an investigational study was conducted over the whole WE-NET structural technology, and at the same time the following were attempted: the constant/mobile comprehensive adjustment of the whole project, evaluation of the developmental results, and optimization of the developmental plans. The results obtained in 6 years of Period I were evaluated traversally and comprehensively, and how to proceed with the development in Period II was proposed, which showed the developmental continuity. (NEDO)

FY 1992 Survey report of the technologies for creating/processing advanced biomaterials. Research and development of the technologies for creating/processing advanced biomaterials (Comprehensive survey and research); 1992 nendo senshin bio zairyo no sosei kako gijutsu chosa hokokusho. Senshin bio zairyo no sosei kako gijutsu no kenkyu kaihatsu (sogo chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

This project is aimed at development of the materials which show functions in a living body by coating a substrate of, e.g., silica or glass, with layered novel peptide synthesized to include unusual amino acid required to have the functions. The existing peptide-related technologies are reviewed and the natural peptide list is prepared. A total of 15 literature is surveyed, and the contents are pigeonholed into 8 items; (1) prospects of peptide engineering, (2) designs of peptide structures, (3) technologies of peptide synthesis, (4) synthesis of unusual amino acid and inclusion into peptide, (5) analysis of peptide structures, (6) physiological activity of peptide, (7) development of peptide materials and function manifestation, and (8) information retrieval of natural peptide (comprising 30 amino acids or less). The item (2) involves analysis and prediction of hydrophobicity of oligopeptide, item (3) chemical synthesis of protein, and protease-aided condensation of dipeptide, item (6) peptide having activity with plant, and item (7) solar cells based on a photoelectric conversion material and pigment-sensitized colloidal titanium oxide. (NEDO)

FY 1997 R/D project of industrial and scientific technologies contracted with NEDO. Report on R/D of organosilicon polymers; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (keisokei kobunshi zairyo no kenkyu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The purpose of this study is to establish fundamental techniques for molecular design, synthesis, material processing and evaluation of organosilicon polymers having excellent electro- and photo-functions, and advanced heat-proof, fire-proof and mechanical properties. This R/D includes (1) R/D of electrical conducting materials by organosilicon polymers, (2) R/D of novel organosilicon polymers applicable to direct lithography, (3) R/D of new silicon-based polymer materials with electro-luminous function, and (4) R/D of silicon-based polymers for new photoconductive materials. In (1), synthesis method of regular polymers with a 3-D structure was developed. Non-volatile dopants were developed, and structures of polymer-dopant composites could be controlled. In (2), precise control of conductivity was examined. Material processing and evaluation techniques were also examined through stabilization of polysilane thin films, optimization of pattern forming conditions, and precision of patterns. In (3), new silicon-based polymers have been synthesized. In (4), two kinds of polymers have been synthesized for development of materials with high photo-carrier generation efficiency and high mobility. 72 refs., 71 figs., 22 tabs.

FY 1998 results of the intellectual basement project using functions of private companies (venture promotion type basement creation R and D project). Development of endocrine disrupter testing method and development of environmental assessment method; 1998 nendo naibunpi kakuran busshitsu ni taisuru shiken hoho kaihatsu oyobi eikyo hyoka shuho kaihatsu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of assessing the risk in relation to endocrine disrupting chemicals, the following were conducted: development of testing/assessment method for endocrine disrupting chemicals, survey of the actual exposure assessment, development of measuring method for the concentration in the environment. In the development of the testing method, the following were carried out: development of a high-throughput screening method for evaluating endocrine disrupting chemicals; as screening testing method using mammals, uterotrophic assay, Hershberger assay using castrated male rats, thyroid hormone assay in pubertal rats, enhanced OECD 407 test guideline for 28-day toxicity test; study on yeast two-hybrid assay for endocrine disrupter; sex-reversal assay for suspected endocrine disrupting chemicals using S-rR strain medaka. In the development of exposure assessment method, estrogenic potency of individual nonylphenol congeners isolated from technical mixtures; determination of endocrine disrupters and related chemicals from industry and nature origin in river water and sediment; research for the flow of industrial origin chemicals; reconstruction of pollution history of chemicals using sediment cores. (NEDO)

FY 1991 report on the results of the contract R and D of the human sense measuring application technology. 2. R and D of the physiological effect measuring technology (2); 1991 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu seika hokokusho. 2. Seiriteki eikyo keisoku gijutsu no kenkyu kaihatsu (2)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

In this paper, the following were studied: (1) easy-wearing net-type brain wave sensor and multi-purpose telemeter; (2) multi-point brain wave measurement. In this fiscal year, the fundamental design and evaluation of these were conducted. In (1), conducted were the study of specifications of system and shape as fundamental design of easy-wearing net-type brain wave sensor, and the evaluation using functional works. As fundamental design of multi-purpose telemeter, studied were the detailed specifications of transmitter and receiver and the system design. In (2), as fundamental design of multi-point brain wave sensor (64 electrodes), conducted were the specifications of system and shape of 19 electrode sensors and the evaluation using functional works trially made. As fundamental design of the analyzer interface, a system was studied for taking brain wave signals of 64 channels into the analyzer by analog/digital conversion. As to the interpolation system of topography, the following were carried out: study of the optimum interpolation system for estimating the electric potential at the portion where the electrode is not installed, based on the electric potential at the portion where 64 brain wave electrodes are installed; and evaluation of the interpolation system using topography by 12-21 electrodes as the pre-stage of 64 electrodes. (NEDO)

Research on variable swirl intake port for high-speed multivalve DI diesel engine. Effects of port configuration on flow characteristics and swirl generation capacity; 4 ben kogata kosoku DI diesel engine no kahen swirl kyuki port ni kansuru kenkyu. Kyuki port haichi ga ryudo tokusei to swirl seino ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Kawashima, J; Ogawa, H; Tsuru, Y [Nissan Motor Co. Ltd., Tokyo (Japan)

1997-10-01

In our previous papers, the variable swirl intake port system which can control a wide swirl ratio range (from 4 to 10) was described. This system consisted of two separate intake ports, one of them has a flow control valve for changing the swirl ratio. In this type of variable swirl system, some variations of port combination, port shape, and position can be designed. In this paper, the intake flow characteristics of various port combinations were analyzed on the basis of a steady-state air flow test and 3-dimensional computations. The results indicate that the total performance of the twin ports can be estimated from that of a single port in any kind of port combination. Some difference in flow patterns were found in a variety of port combinations even if each swirl ratio is similar. The selected port combinations in our previous study are good for a wide swirl control range. 11 refs., 9 figs., 1 tab.

Report on achievements in fiscal 1999 on research and development of the technology to create biological bonding substances utilizing particulates under the industrial and scientific technology research and development theme [university collaborated type]. Research and development of the technology to create biological bonding substances utilizing particulates; 1999 nendo biryushi riyogata seitai ketsugo busshitsu nado sosei gijutsu no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper describes the achievements in fiscal 1999 on development of the technology to create biological bonding substances utilizing particulates. In fixing ligands onto particulates, it is necessary that various compounds be fixed with their receptor bonding specificity maintained. Therefore, carboxylic acid, thiol and bromoacetyl groups were introduced into the particulates. Capping them by using methoxyacetyl was found capable of suppressing non-specific adsorption. Opioid compounds were synthesized for their fixation onto particulates for selection and separation. Carrying particulate bonding precursors in latex beads was realized. Synthesis will continue on opiod compounds in which amide groups are introduced into different positions to provide the particulate carrying ligands with diversity. Biological receptors for different compounds were obtained and refined by using compound fixing particulates. Refinement and acquisition were possible on FK506 bonded protein in a short time from cell extraction liquid by using the fixing particulates for the FK506 bonded protein. The paper also describes analysis of bonded domains, and position-specific fixation of the biological receptors. (NEDO)

Project for surveying improvement in energy demand and supply structure (comprehensive survey on improvement in energy demand and supply). FY1998 report on achievements of Technical survey on pyroelectric power generation systems; Energy jukyu kozo kodoka chosa jigyo (energy jukyu kodoka sogo chosa). Shoden hatsuden system no gijutsu chosa 1998 nendo seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

This paper reports the achievements on research of pyroelectric power generation systems in fiscal 1998. In the research, a small continuous pyroelectric conversion equipment was fabricated and experimented. The experiment using an aluminum foil electrode revealed that the foil melts during discharge opening holes, thus making it impossible to increase net conversion efficiency. The net conversion efficiency was derived in an experiment using foil evaporated with indium instead of the aluminum foil. Indium has inferior electric conductivity to aluminum, but is melting point is as low as 145.6 degrees C. Therefore, if a pyroelectric film had electric fatigue due to use over an extended period of time, indium may be melted to make recovering and reusing pyroelectric copolymer possible. Thus, the indium electrode was found suitable for pyroelectric conversion. Analysis of the experimental data indicated that the final possible net output can be 7.6 W/m{sup 2} if each operation variable considered possible in the future is superimposed on the pyroelectric film. This survey revealed that low-temperature waste heat can be converted to high voltage continually by using the pyroelectric conversion equipment at CANMET Energy Technology Centre. (NEDO)

General report of entrustment investigation for demonstration tests of turnover from oil to methanol in the thermal power plants in fiscal 1995. Total assessment of methanol using power generation technology; 1995 nendo sekiyu karyoku hatsudensho methanol tenkan nado jissho shiken itaku gyomu hokokusho sokatsu hokokusho. Methanol riyo hatsuden gijutsu sogo hyoka chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

To promote the introduction of methanol fuel into the thermal power plants, total assessment was provided. For calculating the methanol production cost, the plant was assumed to be constructed in the Southeast Asia or Middle East. Two methods, i.e., steam reforming and gaseous phase fluid methods, were investigated. Since the price of natural gas is low in the Middle East, the methanol production cost by the gaseous phase fluid method is estimated to be about 1.5 yen per thousand kcal. The transportation cost can be reduced into one-half to one-third of current cost using a large-scale tanker. Although the heating value of methanol per weight is lower than that of LNG, the volume flow of methanol is similar to that of LNG due to its low specific gravity. Conceptual designs were conducted for some power generation systems, such as gas turbine of combined cycle, diesel engine, and fuel cell. The power generation cost was estimated to be 8 to 9 yen per kWh, which depends on the receiving price of methanol. It is nearly equivalent to that of LNG combined cycle power generation. There are no problems of air pollution and ash disposal. When considering the long-term security of energy sources, the use of methanol would be one of the selections as utilization of natural gas. 6 refs., 33 figs., 25 tabs.

General report on the results of the development of fuel cell technology such as urban energy center. Evaluation study of life of phosphoric acid fuel cells (fiscal 1995 and 1996); Toshi energy center nado nenryo denchi gijutsu kaihatsu kenkyu seika sogo hokokusho. Rinsangata nenryo denchi jumyo hyoka kenkyu (1995 kara 1996 nendo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Receiving subsidies from MITI, NEDO carried out this project in fiscal 1995 and 1996 as a joint research with Technology Research Association for Phosphoric Acid Fuel Cell Power Generation System and others. The project aimed at developing the accelerated test method which can evaluate in a short time the cell life of phosphoric acid fuel cells (PAFC) and the lowering of characteristics. The accelerated test method of PAFC life is thought to be a tool indispensable for the promotion of commercialization, but the accelerated test method like the usual material evaluation has not yet been established. To solve this problem, procedures were developed to rationally plan the accelerated test on short stacks of full scale based on the small cell test data. Here, to rationally estimate the operational state under actual conditions based on the data on the accelerated test, it is necessary to fully understand the mechanism of deterioration of PAFC. By conducting in parallel the element study for the basic elucidation of cell deterioration phenomena, obtained was the useful information/knowledge which back up the results of the accelerated test scientifically. 168 figs., 33 tabs.

Fiscal 2000 achievement report. Development of energy use rationalization-oriented silicon manufacturing process (Development of silicon substrate manufacturing technology for high-quality solar cell); 2000 nendo shin energy sangyo gijutsu sogo kaihatsu kiko kyodo kenkyu gyomu seika hokokusho. Energy shiyo gorika silicon seizo process kaihatsu (Kohinshitsu taiyodenchiyou silicon kiban seizo gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development was conducted for enhancing productivity and energy conservation by rendering continuous and automatic the electromagnetic casting process for manufacturing polycrystalline silicon substrates for solar cells. In the manufacture of ingots for substrates by continuous electromagnetic casting, the chuck type system for feeding power to the melt plasma was replaced by a roller type system, and the power feeding position was moved to the high temperature region. Also, an on-line ingot slicing technique was established. In the manufacture of substrates at a slicing rate of 300 {mu}m/minute, productivity of 115,000 wafers/month, yield of 98%, and thickness tolerance of 30 {mu}m were achieved. A high-speed cleaning technique was developed using a jet stream, by which the cleaning time was reduced to 5 minutes and the slurry recovery rate was elevated to 95%. Based on these, substrate-related costs in the case of 100 MW/year production was calculated, which resulted in a cost of 98.8 yen/wafer (target: 103.3 yen/wafer) for manufacturing 15 cm square substrates from ingots and in a 15 cm square substrate slicing and cleaning cost of 135.1 yen/wafer (target: 135.4 yen/wafer). (NEDO)

Fiscal 1997 survey of overseas coal import base arrangement and promotion. Effects of the expansion of coal trade by IPP on the supply/demand of general coal in Asia; 1997 nendo kaigaitan yunyu kiban seibi sokushin chosa. IPP ni yoru sekitan boeki no kakudai ga Asia no ippantan jukyu ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

In consideration of the coal situation in the Asia/Pacific region, a study was made of effects of the expansion of coal trade by IPP on supply/demand of general coal in Asia. When aggregating increases in demand of general coal for electric power use in ten Asian counties, they will be an increase of 130.75 million tons in 2005 over 1997. Fifty nine percent of it is equivalent to the increase by IPP and exceeds the demand expanded by electric utilities operators. Further, a possibility is predicted of contracts and coal quality being different from until now. However, there will be a lot of cases in which plans of constructing power plants in Asia are not so developed as expected except Japan, Korea and Taiwan, and also the effect of the currency crisis starting in Thailand largely affects. In terms of the coal supply, countries which export general coal are only China and Indonesia. Indonesian coal is expanding its production and export rapidly and remarkably. The environmental control in Asia has been tightening, and the fuel selected by IPP is mainly coal rather than natural gas. 40 refs., 94 figs., 179 tabs.

Report on achievements of research and development of a technology to apply human senses to measurements in fiscal 1994. 2. Main issue (Part 1 for research and development of a physiological effect measuring technology); 1994 nendo ningen kankaku keisoku oyo gijutsu no kekyu kaihatsu. 2. Honronhen (Seiriteki eikyo keisoku gijutsu no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

This research and development was performed on (1) a composite physiological function measuring technology for stress measurement, (2) a contact-free skin temperature measuring technology, and (3) a stress indexing substance measuring technology. With regard to the subject (1), the target for the current fiscal year is to restructure a small restraint-free skin impedance measuring device into a practical device that can be used easily at working sites. In order to achieve the goal, electric power conservation and size reduction were moved forward by improving the circuit design, and stabilized measurement, in which the measurement algorithm is made more intelligent, was realized. With regard to the subject (2), the contact-free skin temperature measurement device having been structured by the previous fiscal year was given improvements in such parts as the infrared and visible image input, image processing, and data indication and sense volume estimation. With respect to the subject (3), the technology was established to measure such stress indexing substances as CS and CA from saliva. Positioning of CS and CA as the stress indexing substance was nearly completed. The stress indexing substance measuring device was tried of structuring the prototype A and prototype B applying the semi-micro specifications for an attempt of clearing the steps toward practically usable device. (NEDO)

Fiscal 1997 report on the results of the cooperative research project under consignment from NEDO on technology for simply setting-up of the molding conditions of engineering plastics; 1997 nendo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku (Engineering plastic no seikei joken kan`i settei gijutsu ni kansuru kenkyu kyoryoku jigyo seika hokokusho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

A cooperative research project was carried out between Japan and Thailand with the aim of developing a system which can simply set up molding conditions using as elements the technology on mold design and injection molding in plastic parts production and the experiment/evaluation technology for making sure of the quality of molded products. In fiscal 1997, based on the basic plan worked out in the previous fiscal year, molding equipment, auxiliary equipment, mold, experimental equipment, injection molding CEA system, etc. were installed at Thailand`s BSID (Bureau of Supporting Industries Development). Supported by equipment manufacturers, the technical guidance was given for operation/maintenance/control of all equipment. At the same time, researchers were sent from Japan, and the joint research was started. Japan received three researchers from BSID for training of molding technology, injection molding CEA program use technology, and experimental evaluation technology. The engineering plastics used for study are polyacetal, polyamide and polycarbonate. 17 refs., 68 figs., 14 tabs.

Research report of FY 1997 on the industrial science and technology development. Technology development of super-metal (technology development of nano-amorphous structural control materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku seika hokokusho. Super metal no gijutsu kaihatsu (nano-amorphous kozo seigyo zairyo no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Research and development of the innovative metals have been conducted, by which the weight reduction of members can be done by drastically improving the strength compared with conventional metals. For the high-rate cluster deposition and super plastic forming technologies, research and development of aluminum-based light-weight materials have been conducted, which provides excellent strength, toughness, and super plastic formability at room temperature. For the high-density energy utilization and control technology (amorphous-A), super-metals have been investigated as high dew point and corrosion resistance materials used for waste incinerators operated under the very severe conditions. These are expected to be applied to the apparatuses and equipment due to their excellent properties. For the controlled cooling technology (amorphous-B), super-metals with excellent soft magnetic characteristics and degree of shape freedom have been investigated for high performance and high efficiency devices including electric/electronic/communication devices, power transmission devices, and various industrial devices and parts. These are expected to contribute to the creation of new markets and the improvement of international competitive force. 123 refs., 160 figs., 33 tabs.

Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium energy field/R and D high performance flat panel display technology (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium energy bun`ya / koseino flat panel display gijutsu no sogo kaihatsu kenkyu (daiichi nendo ) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

One of the subjects in technology supporting the highly information-oriented society which will develop and diversify toward the 21st century is the construction of high grade man/machine interface. For it, high precision/high luminance/energy saving/thin plane displays are strongly requested. This R and D is to indicate models of systematical development in the region of element technology individually existing in the Shikoku area by forming a regional consortium in the industry/universities/government. Creation of new industries by gathering display related enterprises is a first step in a plan to realize `Display Island Shikoku.` As a concrete target, with the use of high-tech diamond semiconducting technology, a development is conducted of the high performance flat panel display using the negative electron affinity (NEA) electron emitter which drastically solves the problems such as luminance, visibility angle and response speed, the subjects on the commercialized liquid crystal flat panel display. 16 refs., 45 figs., 8 tabs.

FY 2000 research cooperation project on the comprehensive research cooperation for environmental technology. Research cooperation for technology for prevention of the water pollution caused by plant waste water in Vietnam; 2000 nendo kenkyu kyoryoku jigyo. Kankyo gijutsu sogo kenkyu kyoryoku (Betonamu koku kojo haisui ni yoru suishitsu osen boshi taisaku gijutsu ni kansuru kenkyu hokoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of increasing the research capability of the Center for Consultancy, Training and Technology Transfer in Vietnam, research cooperation for prevention of water pollution was given for plants of the local industry located in the suburbs of Hanoi city. In the survey of the actual state of the water pollution in the industrial area in the suburbs of Hanoi city, the following was found out: In the area, approximately 110 companies of the production industry such as livestock feed, papermaking, dyeing, brewing, construction materials, etc. are in operation and are discharging the untreated waste water into rivers and waterways because waste water treatment facilities are not prepared yet. In this research cooperation, the following were carried out: detailed survey of specified plants and proposal for improvement, training of Vietnamese researchers/engineers in charge of water pollution prevention technology, invitation to/training at Japan of Vietnamese managers/researchers, seminar to be held on the site, equipment to be given that is needed to measure water quality. The equipment to be given is a portable multi-item water quality meter and analytical equipment such as spectrometer, atomic absorption spectrophotometer and gas chromatograph. (NEDO)

FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy. First year report. Development of a next generation biopolymer information measuring system based on the nano channel electrophoresis; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy. Nano channel denki eido ni motozuku jisedai seitai kobunshi joho keisoku system no kaihatsu (dai 1 nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

On the basis of the nano channel electrophoresis technology, the construction was proceeded with of a system which integrates the basic process such as reaction, separation and detection needed for measuring biopolymer information and analyzes a number of samples simultaneously and with high accuracy/high sensitivity. Studies were made in the following three fields: 1) development of the basement technology on extraction/amplification/separation/detection of biopolymer; 2) development of micro-processing technology and system design and study on the development of device; 3) comprehensive investigational study. In 1), developmental technology is divided into the following: technology to effectively fraction/refine biopolymer from biological samples, technology for recognition control and manipulation of biopolymer, technology of amplification use micro-reaction of biopolymer, multiple selection technology of biopolymer using the specific molecular recognition, and technology for ultra-high speed separation of biopolymer. As to the multiple selection technology, DNA terminal recognizing hemin is altered by thiol group and connected to the surface of electrode to make an electrode type hemin recognition device. (NEDO)

FY 2000 report on the results of the regional consortium R and D project - Regional consortium field. Third year report. R and D of the manufacturing technology of hybrid type biocompatible hard tissue substituting materials; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium bun'ya. Hybrid gata seitai yugo kinosei kososhiki daitai sozai seizo gijutsu no kenkyu kaihatsu (dai 3 nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

As instrument materials substituting for hard tissue such as tooth root and artificial hip joint, the technology development is being proceeded with of the use of high-biocompatible {beta} Ti alloys coated by hydroxy apatite. Studies were made in the following 6 fields: 1) design of high-biocompatible {beta} Ti alloys, system control and dynamic evaluation; 2) development of high efficiency calcium phosphate ceramics (hydroxy apatite) and development of surface coating technology; 3) development of melting casting technology of high-biocompatible {beta} Ti alloys; 4) biological evaluation of biocompatibility of high-biocompatible {beta} Ti alloys and completion of dental precision casting technology; 5) basic research on affinity of low rigidity Ti alloys (trial manufacture); 6) development of technology of precision processing and precision finishing processing of alloys. In 5), in the test on affinity of the trial-manufactured alloys, stainless steel and existing Ti alloys, it was verified that the trial-manufactured alloys were excellent in affinity. (NEDO)

FY 1991 report on the results of the contract R and D of the human sense measuring application technology. Volume 2. R and D of the physiological effect measuring technology (Part 1); 1991 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu itaku kenkyu seika hokokusho. 2. Seiriteki eikyo keisoku gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-01

Targets of the total development is to develop technology to non-invasively/simply measure changes in physiological function for physical and mental stimuli and to develop a human sense measuring technology needed to realize 'comfortableness.' As a part of it, the following R and D were conducted in this fiscal year. As to the R and D of skin impedance measuring, measuring methods such as the conducting method and potential method were studied. Further, an experiment with a person to be tested was conducted using the experiment use electrode. And detected were skin impedance changes caused by mental strain stress which were distinguished from changes caused by external environment. As the blink reflection measuring method, the paper took up the eyelid micro-vibration method under consideration and verified effectiveness of the method. The data were acquired using the same person as tested in the above-mentioned experiment when he is not tired, and the extraction of parameters of blink reflection which change according to working loads was studied. As to the continued blood pressure measuring technology, a measuring method which gives no loads on the person tested was studied, and the measuring portion where stable output can be obtained was selected. In addition, small/lightweight continued blood pressure measuring instrument which can be used in daily life was trially manufactured and designed. (NEDO)

Effects of sintering and paste-baking conditions on PTCR characteristic of (Ba,Sr)TiO{sub 3} vacuum-sintered compact added with TiO{sub 2}(Ti) powder; TiO{sub 2}(ti) fun tenka (Ba,Sr)TiO{sub 3} shinku shoketsutai no PTCR tokusei ni oyobosu shoketsu oyobi paste yakitsuke joken no eikyo

Energy Technology Data Exchange (ETDEWEB)

Kim, J.; Hayashi, K. [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science

1999-04-15

The effects of sintering temperature (T{sub s}; 1,573 {approx} 1,748K) and time (t{sub s}; 0.6 {approx} 14.4ks) and paste-baking-temperature or heating temperature (T{sub b} or T{sub h}; 673 {approx} 1,273K; t{sub b} is 0.3ks) on PTCR characteristic were investigated for (Ba, Sr)TiO{sub 3} vacuum-sintered compact added with 3.9mass% TiO{sub 2}(Ti) powder of 12.5mass% TiO{sub 2}. The results obtained were as follows; (1) PTCR characteristic developed at all T{sub s} (t{sub s}=3.6ks, T{sub b}=853K). The electrical resistivity at room temperature ({rho}{sub rt}) showed a minimum value of 1.8 times 10{sup 2}ohmcenter dotcm and the {rho}{sub max}/{rho}{sub rt} showed a maximum value of about 10{sup 6} at 1,723K. (2)For all t{sub s} (T{sub s}=1,623K, T{sub b}=853K), PTCR characteristic developed. The {rho}{sub rt} showed a minimum value of 2.6 times 10{sup 3}ohmcenter dotcm at 7.2ks. (3) At T{sub b} above 823K (T{sub s}=1,623K, t{sub s}=3.6ks), PTCR characteristic developed. The {rho}{sub rt} showed a minimum value of 1.0 times 10{sup 3}ohmcenter dotcm. (4)The {rho}-T curve of (Ba, Sr)TiO{sub 3}+TiO{sub 2}(Ti) vacuum-sintered compact was affected more largely by T{sub s}, t{sub s} and T{sub b} than that of (Ba, Sr)TiO{sub 3} air-sintered compact. This was considered to be mainly due to the porous and fine gained microstructure in the former compact. (author)

Fiscal 1999 research result report on energy and environment technology demonstration research support project (International joint demonstration research project). Improvement of long-distant power transmission efficiency and reliability, and its environmental impact assessment; 1999 nendo chokyori soden hoshiki ni kansuru soden koritsu to soden shinraido no kojo oyobi kankyo eno eikyo hyoka seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Japan-Russia international joint research was made on overhead ultrahigh-voltage DC power transmission lines for transmission loss reduction and reliability improvement, and an optimum international power supply cable system, considering energy saving and environment conservation. Using the European-Russian DC power transmission line of {+-}500kV and 4GW as a model, comparison was made between a model using Russian round strands and glass insulators and a model using Japanese low-loss wires and insulators. As for improvement of the reliability in cold districts, Russian design techniques for tower structure and ice loading were reasonable to counteract galloping oscillation and ice load. In evaluation and selection of optimum underground and marine cables, study was made on cable specifications using the Turkey-Russia power transmission route as a model. The environmental assessment result of these cables showed that XLPE cable under development is optimum. (NEDO)

FY 1991 report on the results of the contract R and D of the human sense measuring application technology. Volume 2. R and D of the physiological effect measuring technology (Part 1); 1991 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu itaku kenkyu seika hokokusho. 2. Seiriteki eikyo keisoku gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-01

Targets of the total development is to develop technology to non-invasively/simply measure changes in physiological function for physical and mental stimuli and to develop a human sense measuring technology needed to realize 'comfortableness.' As a part of it, the following R and D were conducted in this fiscal year. As to the R and D of skin impedance measuring, measuring methods such as the conducting method and potential method were studied. Further, an experiment with a person to be tested was conducted using the experiment use electrode. And detected were skin impedance changes caused by mental strain stress which were distinguished from changes caused by external environment. As the blink reflection measuring method, the paper took up the eyelid micro-vibration method under consideration and verified effectiveness of the method. The data were acquired using the same person as tested in the above-mentioned experiment when he is not tired, and the extraction of parameters of blink reflection which change according to working loads was studied. As to the continued blood pressure measuring technology, a measuring method which gives no loads on the person tested was studied, and the measuring portion where stable output can be obtained was selected. In addition, small/lightweight continued blood pressure measuring instrument which can be used in daily life was trially manufactured and designed. (NEDO)

Report for fiscal 1981 on comprehensive survey for nationwide geothermal resources. Survey on radar imaging method - geothermal conception design (Associated material 3 - materials related to U.S. geothermal analysis contractors and consultants); 1981 nendo zenkoku chinetsu shigen sogo chosa hokokusho. Radar eizoho chosa (chinetsu kaiseki gainen sekkei futai shiryo 3 (Beikoku chinetsu kaiseki contractor oyobi consultant kankei shiryo))

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-10-01

This paper summarizes the U.S. geothermal analysis contractors, including the Aero Service Corporation, the EG and G Group, the QEB Group, and the Republic Geothermal, Inc., and the consultants, including the Remote Sensing Consultants. For the Aero Service Corporation, the paper states histories of and books written by major personnel. For the EG and G Group, the paper states the outlines of such companies as EG and G Services, EG and G Geometrics, Mars Associates, Inc., and UURI, as well as histories of and books written by major personnel. For the QEB Group, the paper states the outlines of such companies as QEB, Inc., and Eureka Resource Associates, Inc. as well as histories of and books written by major personnel. For the Republic Geothermal, Inc., the paper states the company outline, histories of and books written by major personnel. For the Remote Sensing Consultants, the paper states the history of and books written by Dr. R.J.P.L. Lyon. (NEDO)

Fiscal 1997 report on the R and D result of industrial science and technology. R and D on super metal (R and D on innovative raw metal materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku seika hokokusho. Super metal no gijutsu kaihatsu (kakushinteki kinzoku sokei zairyo no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Study was made on the applicability of mechanical milling (MM) and mechanical alloying (MA) to Fe system alloys. Metastable austenitic stainless steels such as SUS316L and SUS304L form {alpha} phases by strain induced transformation due to MM, and are subjected to further plastic deformation. Nano-size fine structure was obtained through inverse transformation into austenite({gamma}) by heat treatment or high-temperature sintering of MM powder. Fine microduplex structure of 620nm in average crystal grain size was obtained for SUS316L. This material showed nearly 3.3 times higher 0.2% tensile proof stress, nearly 1.8 times higher tensile strength, and 35% higher elongation than conventional ingot steels. Solid solution powder of 12Cr-Mo-W ferritic steel was sintered by hot isostatic pressing (HIP) under low- temperature and ultrahigh-pressure conditions of 650degC and 588MPa. The as-HIP`ed sample and sample annealed at 800degC showed average {alpha} grain sizes of 33 and 50nm, respectively, and a strength twice as high as that of 12Cr steel. 97 refs., 60 figs., 18 tabs.

Fiscal 1997 report on the results of the introductory R and D of the New Sunshine Project under a consignment from NEDO. Introductory R and D of the supercritical fluid use technology; 1997 nendo `New Sunshine keikaku` sendo kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Chorinkai ryutai riyo gijutsu sendo kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The R and D of chemical reaction using supercritical fluids started in fiscal 1997. In the R and D of solvent reaction, as the research on polymer decomposition with supercritical water, studies were conducted of the mechanism of conversion reaction to chemical materials, cleavage mechanism of stable chemical bonds, and synthetic reaction in the supercritical state reaction field. In the research on oxidation reaction, as the study of complete oxidation in supercritical water for high efficiency energy recovery, studies of complete oxidation of liquid fuels, and complete oxidation of solid fuels. In the research on hydrogenation, studies of lightening of heavy oil in supercritical water, etc. In the R and D of the basic technology, studies of corrosion mechanism of metals in supercritical water, construction of the basic framework for technical database of supercritical fluids, etc. In the survey of technical trends and new research themes, the introductory R and D of element technology, etc. were conducted, and the results were described of the survey of technical trends and new research themes and the trend survey of overseas technology. 314 refs., 87 figs., 81 tabs.

Report on the results of the fiscal 1997 R and D under consignment from NEDO of photon measuring/processing technology (R and D of petroleum production system high-grade measuring/processing technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku photon keisoku kako gijutsu (sekiyu seisan system kodo keisoku kako gijutsu kenkyu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The R and D were conducted of high-strength and high-accuracy welding/joining technology using laser, technology to measure and assess the joining state of structures and defects around the surface of structures and inside structures by high accuracy and high resolution, and technology/equipment to generate a laser light source for the tool, which are all required to remarkably enhance safety/reliability of oil drilling facilities working in the severe environment. In fiscal 1997, as the R and D of oil production system high-grade measuring/processing technology, technical study, study of measures to be taken, operating experiment, assessment, examination, etc. were conducted on the following themes: 1) macroscopic processing technology (R and D of high-reliability laser welding technology), 2) non-destructive composition measuring technology (R and D of internal measurement and photoelectron spectroscopy using short-wavelength radiation), 3) tight-focusing all-solid-state laser technology (R and D of fiber laser), 4) tight-focusing all-solid-state laser technology (R and D of high-efficiency laser diode), and 5) comprehensive investigation of phonics engineering (investigation for photon-applied materials processing technology). 256 refs., 205 figs., 18 tabs.

Fiscal 1993 report on results of R and D on innovative technology for producing advanced biomaterial. Peptide applied carbon dioxide fixation/effective utilization technology (Second volume: comprehensive investigation and research); 1993 nendo senshin bio zairyo no sosei kako gijutsu no kenkyu kaihatsu seika hokokusho (sogo chosa kenkyu). 2. Peptide oyo nisanka tanso koteika yuko riyo gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Technology was developed for preparing functional materials by synthesizing new functional peptides in which non-natural amino acid needed for the functional manifestation was introduced, and by fixing the peptides to the surface of a base plate such as silica glass or modifying the surface with them. As the related technological investigation, the following six areas were surveyed. (1) Structural design of peptides, (2) synthesis of peptides by chemical and enzyme methods, (3) synthesis of non-natural amino acid and its introduction into peptides, (4) structural analysis of peptides, (5) physiological activity of peptides, and (6) materialization and functional manifestation of peptides. With the exception of the area (5) consisting of one advanced research case, other areas were constituted of analysis, general remarks and research cases. The area (6) was constituted of materialization technique 1 and 2, film function and peptide, catalytic action 1 and 2, and one research case; the materialization technique was defined as a technique for modifying the surface of a synthetic resin, metallic or silica glass substrate with functional peptides; and an explanation was given to the present state of the fixation, pattern formation and integration technologies. (NEDO)

Combustion-driven oscillation in a furnace with multispud-type gas burners. 4th Report. Effects of position of secondary air guide sleeve and openness of secondary air guide vane on combustion oscillation condition; Multispud gata gas turner ni okeru nensho shindo. 4. Nijigen kuki sleeve ichi oyobi nijigen kuki vane kaido no shindo reiki ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Akiyama, I.; Okiura, K.; Baba, A.; Orimoto, M. [Babcock-Hitachi K.K., Tokyo (Japan)

1994-07-25

Effects of the position of a secondary air guide sleeve and the openness of a secondary air guide vane on combustion oscillation conditions were studied experimentally for multispud-type gas burners. Pressure fluctuation in furnaces was analyzed with the previously reported resonance factor which was proposed as an index to represent the degree of combustion oscillation. As a result, the combustion oscillation region was largely affected by both position of a guide sleeve and openness of a guide vane. As the openness having large effect on the ratio of primary and secondary air/tertiary air and the position hardly having effect on the ratio were adjusted skillfully, the burner with no combustion oscillation region was achieved in its normal operation range. In addition, as the effect of preheating combustion air was arranged with a standard flow rate or mass flow flux of air, it was suggested the combustion oscillation region due to preheating can be described with the same manner as that due to no preheating. 5 refs., 8 figs.

Change of environmental factors in different site which effect the conversion efficiency of photovoltaic module. Comparison of the environmental factors in Shinjuku Tokyo with the one in Chino Nagano; Kotonaru chiten ni okeru taiyo denchi no henkan koritsu ni eikyo wo ataeru kankyo inshi no henka. Tokyoto Shinjukuku to Naganoken Chinoshi no kankyo inshi no hikaku

Energy Technology Data Exchange (ETDEWEB)

Higuchi, T.; Tani, T.; Hirata, Y.; Inasaka, T. [Science University of Tokyo, Tokyo (Japan)

1997-11-25

Environmental factors affecting conversion efficiency of solar cells were measured in Tokyo and Nagano to comparatively study the difference. In the study, measurement was made of intensity of global solar radiation on an inclined surface (insolation intensity), ambient air temperature, and distribution of spectral solar radiation at the two points. Also measured were output characteristics of polycrystal silicon solar cell modules and amorphous silicon solar cell modules. The result of the comparative analysis was as follows: The annual inclined global solar radiation amount integrated in 1996 is 27% more in Nagano than in Tokyo. The weighted average insolation intensity in Nagano is 0.09 kW/m{sup 2} higher in Tokyo. The weighted average cell temperature in Nagano is 4degC lower than in Tokyo. The effective spectral ratio in Nagano is 1-2% lower both in polycrystal Si and amorphous Si than in Tokyo. Thus, it was inferred from that environmental factors are different that conversion efficiencies of photovoltaic modules were different. 6 refs., 5 figs., 5 tabs.

Fiscal 2000 achievement report. Research and development of fast-acting innovative energy-environment technology (Development of fast-acting high-efficiency solar cell technology - Development of high-quality ingot manufacturing technology); 2000 nendo shin energy sangyo gijutsu sogo kaihatsu kiko itaku kenkyu gyomu seika hokokusho. Sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu (Sokkogata kokoritsu taiyo denchi gijutsu kaihatsu - Kohinshitsu ingot seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development was conducted of a technology for manufacturing an ultrathin polycrystalline silicon solar cell capable of efficiency enhancement and cost reduction earlier than the types of polycrystalline solar cells now available on the market. In this fiscal year, a silicon melt/solidification experimenting apparatus was built for manufacturing high-quality silicon ingots. Using an apparatus with its performance similar to the newly built one, a preliminary experiment was conducted involving high-purity silicon ingot manufacturing. In the experiment, boron was added to 75 kg of silicon for semiconductor devices so that its resistivity may be 0.5 ohm-cm. The silicon was melted in a quartz mold, and then subjected to unidirectional coagulation at 0.13 mm/min that started at the bottom to proceed upward. The result was a silicon ingot 44 cm times 44 cm times 17 cm (height). The ingot thus obtained exhibited 0.4-0.8 ohm-cm in resistivity distribution. Solar cells produced from the ingot showed a conversion rate of 16.9%. (NEDO)

Fiscal 2000 achievement report on the venture business assisting type regional consortium - Core industry creation type. Comprehensive research and development for reducing ABS (MABS) sensor system into small module for enhancing vehicle steering safety; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Koji no sharyo soansei wo jitsugensuru ABS (MABS) sensor system no kogata module ka ni tsuite no sogo kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The effort aims to develop a sensor system to enable overall VDC (vehicle dynamic control). The goal is to manufacture a small module type sensor system more than 20 times higher than the conventional type in responding speed and accuracy, which will use a novel ABS (anti-lock braking system) capable of direct and real-time measurement of axial forces in the four directions. The prototype module will be a package in which a system-on-a-chip accommodating peripheral circuits is integrated with a sensor. In the effort to develop a novel multi-axial sensing system (MASS) for a smaller ABS, a circuit optimization technology was developed. A dedicated IC (integrated circuit) was developed for a system to process a large volume of signals. In the effort to develop technologies for packaging the novel sensor system and for constructing modules, technologies were developed for integrating sensor components and an IC into one, module junctioning, module installation, simplification of the installation process, and for the manufacturing of modules. Developed in the effort to optimize MASS were technologies involving the selection and evaluation of sensor components and the enhancement of such processes, optimization of the sensor itself, and the improvement of the sensor system for higher efficiency in calculation. Sensor modules were tested aboard vehicles and the compatibility of the system-on-a-chip with the MASS module was confirmed. (NEDO)

Fiscal 1996 report on the results of the R and D under a consignment from NEDO of the environment friendly type production technology. High-functional chemical synthesis bioreactor (for public); 1996 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kankyo chowagata seisan gijutsu (kokino kagaku gosei bioreactor) kenkyu kaihatsu seika hokokusho (kokaiyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For the purpose of developing production technology of chemical substances which are resource conservative, energy saving and less in environmental loads, a R and D was conducted of a high-functional chemical synthesis bioreactor. The paper reported the results of fiscal 1996. As for proliferation control breeding technology, relating to the switch control technology of proliferation related genes by regulatory factors, the effectiveness on an incubator level was demonstrated, and at the same time improvement of reactor performance in using this technology was studied on paper. As to the manifestation control breeding technology, the actual design of the development of manifestation promotion technology by bent DNA, etc. was proceeded with, and at the same time the following were commenced: selection of bent DNA, confirmation of bent characteristics, and work of vector construction using candidate bent DNA. Further, the simple assessment system of manifestation vectors was constructed. In the development of bioreactor system technology, the actual design was started of the two-stage culture continuance system which separated proliferation and enzyme production. 48 refs., 41 figs., 6 tabs.

Fiscal 2000 achievement report. Development of energy use rationalization-oriented silicon manufacturing process (Survey and study of analysis of commercialization of solar-grade silicon material manufacturing technology); 2000 nendo shin energy sangyo gijutsu sogo kaihatsu kiko kyodo kenkyu gyomu seika hokokusho. Energy shiyo gorika silicon seizo process kaihatsu (Taiyodenchiyou silicon genryo seizo gijutsu no jitsuyoka kaiseki ni kansuru chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The trend of technology development, problems harbored therein, trend of the market, and the like were investigated for supporting the development of technologies for the mass production and commercialization of solar-grade silicon materials. Concerning the future of production enhancement and cost reduction in the manufacture of polycrystalline silicon solar cells, studies were made from the technological viewpoint. The results are shown below. It is estimated that approximately 4,500 tons of material silicon will be necessary in 2005 and 6,500-10,700 tons in 2010. Since the melting purification method of NEDO (New Energy and Industrial Technology Development Organization) now under development step by step toward commercialization as well as the conventional source will provide the necessary amount of material silicon, it is inferred that the development of solar cells will go on without any restraint originating in the semiconductor industry. With the commercialization of the technologies so far developed and the development/commercialization of the fast-acting high-performance solar cell technology, probabilities are high that the polycrystalline silicon solar cell manufacturing cost in 2010 will be as low as to be on the 100 yen/W (93-118 yen/W) level which is the level now held up as the goal. (NEDO)

Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). The R and D aims at establishment of observation/manipulation technology of atoms and molecules as common basic technology in various industrial fields such as new material, electronics, bio-technology and chemistry. The R and D thus aims at establishment of observation/manipulation of solid surfaces and DNA organic molecules, formation of fine structures of atomic surface arrangement, and calculation/ simulation for predicting a reaction theorem of atom and molecule surfaces. In fiscal 1997, research was made on improvement and development of computer simulation environment, and description of an excited state of electrons by Green function. Establishment of a construction method and computation code is under investigation for pseudo- potential dependent on excitation energy. Survey was made on research trends of the atom technology by visiting overseas academic societies and institutions. International Symposium on Atom Technology was also held in Tokyo in Nov. 1997

FY 1997 R/D project of industrial and scientific technologies contracted with NEDO. Report on technology development of utilization of biological resources such as bioconsortia (development of analytical techniques of bioconsortia); 1997 nendo sangyo gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu (fukugo seibutsukei kaiseki gijutsu no kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Bioconsortia are microbial composites composing of more than two kinds of microorganisms with special functions. To utilize their advanced functions, some techniques have been developed for analyzing their functions and interactions, and for identification, separation and incubation of the constituent microbial groups. In FY 1997, an investigation was made on technology trends, domestic researchers, and research topics related to bioconsortia. To manage and promote the progress of research at the National Institute of Bioscience and Human-Technology where the centralized management of this project is conducted, meetings are held once a month to examine the progress at the institute, in which reports are made and discussions are held on how each research item is progressing. In addition, meetings of the committee to promote research are held every other month to consider and examine measures required for promoting the research. Re-entrustment of research has been made on two subjects, i.e., `Studies on biological significance of symbiotic microorganisms` by Prof. Ishikawa of the University of Tokyo, and `Study on the relationship between the biosynthesis of useful terpenic materials of plant origin and the differentiation of plant tissues, and their effective production by plant cell cultures` by Prof. Inoue of Gifu Pharmaceutical University. 27 refs., 13 figs., 1 tab.

Report on the results of research and development under a consignment from NEDO of glycoconjugate production utilizing technologies. Development of technologies to fix and effectively utilize carbon dioxide by applying glycoconjugates; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Fukugo toshitsu seisan riyo gijutsu no kenkyu kaihatsu (fukugo toshitsu oyo nisanka tanso koteika yuko riyo gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper reports research results in fiscal 1997 for the `research and development of glycoconjugate production utilizing technologies`. In synthesizing, utilizing and remodeling technologies for glycoconjugates by means of chemical synthesis, studies were performed on developing methods to synthesize Gal {beta}1-3Gal NA(c {alpha})1-0-Serine in preparative scale, synthesizing high mannose type sugars of natural type without protection groups, and linking GlcNA or GalNAc onto partial peptide of fibroblast growth factor (FGF). In synthesizing, utilizing and remodeling technologies for glycoconjugates by using biological methods, studies were carried out, with regard to glycoconjugate synthesizing, utilizing and remodeling technologies utilizing animal cells, on identifying sugar structures of IFN-{gamma} produced from CHO cell line, and isolating CHO cell lines introduced with genes of sugar transferred enzyme GnTIV and/or GnTV. Furthermore, studies were conducted on glycoconjugate synthesizing, utilizing and remodeling technologies utilizing microorganisms, and glycoconjugate structure analyzing technologies. In addition, overall investigation was made on glycoconjugate production utilizing technologies. 113 refs., 76 figs., 18 tabs.

Industrial and scientific technology research and development project in fiscal 1997 commissioned by the New Energy and Industrial Technology Development Organization. Research and development of superconducting materials and transistors (report on overall investigation of superconductive devices); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Chodendo zairyo chodendo soshi no kenkyu kaihatsu (chodendo soshika gijutsu kaihatsu seika hokokusho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes development of superconducting new function transistors. Fiscal 1997 as the final year of the project advanced improvement in such transistor-using processes as formation and micro-processing of superconducting thin films to show enhancement in characteristics of high-temperature superconducting transistors and possibility of their application utilizing their high speed motions. Furthermore, fundamental technologies were studied with an aim on junction transistors to be applied as circuits. For field effect transistors, evaluation was performed on critical current distribution of step-type particle boundary junction to make it possible to evaluate characteristics of hundreds of transistors. At the same time, a magnetic flux quantum parametron gate with three-layer structure was fabricated to identify its operation. In superconducting-base transistors, strong reflection was recognized on temperature dependence of permittivity of an Nb-doped strontium titanate substrate used for collectors, by which barrier height was reduced. In the junction transistor and circuit technology, isotropic ramp-edge junctions were fabricated, and so was a frequency divider circuit with single magnetic flux quantum mode operation for evaluating high-speed response characteristics. High time resolution current was observed successfully by using a high-temperature superconducting sampler system. 148 refs., 127 figs., 4 tabs.

Fiscal 1998 survey report. Medical equipment (Development of fine sampling/analysis system for blood / Development of high-precision 3-D image diagnosis system / Development of low-invasion operation support system / Total development of artificial internal organ technologies); 1998 nendo chosa hokokusho. Iryo kiki (ketsuekinado biryo saishu, biryo bunseki system kaihatsu/koseido sanjigen eizo shindan system kaihatsu/teishinshu shujutsu shien system kaihatsu/jinko zoki gijutsu sogo kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For efficient medical care supply systems, the R and D of advanced medical care technology and equipment largely contribute to productivity improvement for medical care services. Among them, a progress of medical care technology is becoming important for preparation of efficient and fair supply systems. MITI thus established 'Medical care and welfare equipment development project' in 1994, and has promoted the strategic long-term R and D project of medical care and welfare equipment as joint R and D project of NEDO and private enterprises. In fiscal 1998, on the development of the fine sampling/analysis system for blood, the high- precision 3-D image diagnosis system, the low-invasion operation support system, and the artificial internal organ technologies since fiscal 1996, this project clarified essential technical issues based on the future view, selected some themes to be newly developed in the future, and surveyed and evaluated the details of their R and D concretely. (NEDO)

Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the synthesis and processing of advanced biomaterials (fixation and effective utilization of carbon dioxide using peptides); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Senshin bio zairyo no sosei kako gijutsu no kenkyu kaihatsu (peptide oyo nisanka tanso koteika yuko riyo gijutsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

In fiscal 1997, study was made on formation of peptides with a biogenic function and molecular recognition function, and peptide materials. The existing automatic design technique of peptides including non-natural amino acids was applied to design of complementary peptides of proteins with known structures to optimize a development technique of ligand. Practical function of peptides as advanced receptor ligand was verified by applying the existing conformation control technique to stable holding of peptide active conformation. Creation of bio-materials, and development of preparation technology of bio-substrates and materializing technology of functional molecular materials were carried out. To construct an electron transfer system by self- organized body of peptides formed on a substrate, a peptide molecular device was prepared and verified using linkers. To use peptides as photoelectron functional molecule, metallized peptide with main helix structure was prepared. The possibility of molecular materials with a fixation function of CO2 was examined. A high-sensitivity bio-sensor was also mentioned. 75 refs., 130 figs., 25 tabs.

Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of silicon-based polymeric materials (development of liquid methane fueled aircraft engine); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo / Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (methane nenryo kokukiyo engine kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This R and D aims at establishing the basic technology on the molecular design, synthesis, use as materials, and evaluation of silicon-based polymers, of which excellent electronic/optical functions, high heat-resistance/combustion-resistance/dynamic characteristic are expected. The paper introduced the results of the fiscal 1997 R and D of them. The themes are as follows: technology of synthesis of silicon-based polymeric materials with sea-island microstructures, interstitial type structure forming technology, composite materials with organometallic complexes and silicon-based polymers, silicon-based polymer structural materials with ring structures, optimization of the Wurtz`s synthesis method of silicon-based polymers, unsaturated and hypercoordinate organosilicic compounds, function of silicon-based polymers, synthesis and polymerization of new silicon-based monomers, development of a new synthesis method of polysilane and the function, development of new application of silicon-based polymers in imaging devices for recording/memory/display of information, molecular design of {pi}-conjugate and {sigma}-conjugate compounds including silicon, and conformation and electronic state of silicon-based polymeric materials. 186 refs., 141 figs., 68 tabs.

Fiscal 1997 R and D project under a consignment from NEDO. R and D of the femtosecond technology (R and D of the monitoring system using high-intensity X-ray pulse for power plants); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Femto byo technology no kenkyu kaihatsu (kokido X sen pulse riyo hatsuden shisetsu monitoring system no kenkyu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper reports the result on R and D of the femtosecond technology in fiscal 1997. Ultrahigh-speed electronic technology is indispensable for industrial basic technologies supporting the advanced information society in the 21st century. Control technology of photonic and electronic states in a femtosecond region is essential. In R and D of metrological technology using ultra-short light-pulses, study was made on generating and controlling technology for ultra- short light/electron beam pulses. Ti-sapphire mode-locked laser was prepared, and it was found that time-fluctuation of mode-locked laser pulses is measurable up to 100 femtosecond level. As measures against an instability of gain-switching semiconductor laser, light injection from the outside was effective. The stable directivity of laser beam was obtained by regenerative amplifier, while less temperature variation of an optical switch was necessary to stabilize energy. To generate femtosecond high-intensity X-ray pulse by collision of laser and electron beams, it was confirmed that sub- picosecond synchronization is possible by RF and picosecond laser synchronization circuit. 48 refs., 89 figs., 11 tabs.

Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the superconducting material and device (technical development of the Josephson device hybrid system); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Chodendo zairyo chodendo soshi no kenkyu kaihatsu (Josephson soshi hybrid system no gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

In order to establish basic technology for hybrid systems of superconducting and semiconducting devices, study was made on ultrahigh speed and low energy consumption properties of Josephson devices. As Josephson IC technology, a logical circuit, ring network, memory circuit, and oxide superconductor logical circuit were studied. As superconducting hybrid system technology, a Josephson device- semiconductor device interface, formation technology of signal transmission lines, and Josephson-MOS IC technology were developed. In fiscal 1997, as Josephson IC technology, switch motion of 4GHz in clock frequency was achieved by new high-density wiring process. Integration of some semiconducting processor elements, junction of surface- stabilized superconducting thin films, and motion of combination structure of some SQUIDs were also confirmed. On the hybrid system, voltage conversion operation of all interfaces was confirmed. Proper logical operation of the Josephson device hybrid circuit was also confirmed. 95 refs., 90 figs., 5 tabs.

FY 2001 report on the integrated evaluation of the research cooperation project. Research cooperation program on the development of environmental measurement use laser radar/research cooperation project on the mining waste water treatment technology using biology; 2001 nendo kenkyu kyoryoku jigyo sogo hyoka hokokusho. Kankyo kesokuyo reza reda no kaihatsu ni kansuru kenkyu kyoryoku - Baio riyo ni yoru kohaisui shori gijutsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

By research groups having been sent, the integrated evaluation was made of the projects on the research cooperation with Indonesia in the development of environmental measurement use laser radar and the research cooperation with China in the mining waste water treatment technology using biology. As to the research cooperation with Indonesia, the purpose/target proposed were almost achieved, and all were favorably carried out. Especially, after finishing the project, the design/manufacture of an on-vehicle type Mie-scattering laser radar were made using the acquired laser technology. And, it was reported that an observation study of the state of air pollution in Bandung city was made using the laser radar. It can be said that generally the research cooperation with China was smoothly proceeded with. However, the Wushan mine is small in scale of management, and therefore, there might have been some points to be reviewed in selection of the mine for research. The pilot plant installed at the Wushan mine is not now operated. If the mine has strong management force, the effective use of the pilot plant after finishing the project might have been studied. (NEDO)

Report of the FY 1995 research cooperation promotion projects (overall evaluation). Research cooperation in fuel cell utilization/district power generation system and village type technique for simplified continuous production of raw palm oil; 1995 nendo kenkyu kyoryoku suishin jigyo (sogo hyoka) hokokusho. Nenryo denchi katsuyo chiiki hatsuden system ni kansuru kenkyu kyoryoku / sonrakugata kan'i renzoku palm arayu seizo gijutsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The research cooperation project for fuel cell utilization/district power generation system is conducted under the research cooperation agreement between NEDO and Electricity Generating Authority of Thailand (EGAT), to demonstrate a 50 kW pilot plant constructed at EGAT's Bang Pakong power station. The fuel cell reforms self-spouted natural gas into H{sub 2} as the fuel. It has produced a total power of 341,921 kWh under the conditions of cumulative operating time: 8,115.4 hours, longest continuous operating time: 1,100 hours, service factor: 89.64%, load ratio: 86.13% and system utilization factor: 77.20%. The fuel technique will be acceptable for Thailand, if it is economically competitive. The project for producing raw palm oil is for Malaysia. The facilities introduced and tested for the new process are a continuous steam-heated fruit remover, fiber/nut separator, and shell cutter. The new process is evaluated to produce higher-quality raw palm oil in higher yield while consuming less energy. The new process, whose steps are automated, saves operating cost, and suitable for Malaysia which is suffering shortage of manpower. (NEDO)

Fiscal 1996 report on the results of the R and D under a consignment from NEDO of the technology to fix and effectively use carbon dioxide using bacteria and microalgae (for public); 1996 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku (saikin sorui nado riyo nisanka tanso koteika yuko riyo gijutsu kenkyu kaihatsu seika hokokusho (kokaiyo))

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For the purpose of contributing to the solution to the global environmental problem, a technology is developed in which by searching for/breeding/developing bacteria, etc. which conduct photosynthesis highly effectively, CO2 is fixed and recycled. The fiscal 1996 R and D is outlined as the utilization of bacteria, microalgae, etc. Obtained were microalgae exceeding the conventional strains in CO2 fixation ability, and bacteria/microalgae excellent in production of polysaccharides, hydrocarbon, lipid, biological active substances, etc. The fundamental study was continued of CO2 integrated enzyme function/reaction system as molecular biological breeding. In the cell fusion, a set-up of conditions for green algae was started. For the confirmation of performance of high dense/quantity culture technology using solar light, further improvement of performance and systematization, 200L scale testing equipment was manufactured. It is a collective reactor and enabled study of ventilation/agitation and control of light strength. A reactor analysis model was constructed. Also including the conversion into useful substances, energy/material balance was systematically studied. Collection of technical literature and information exchanges were made in Japan and overseas. 276 refs., 475 figs., 156 tabs.

Analysis and evaluation for practical application of photovoltaic power generation system. Analysis and evaluation for thin substrate polycrystalline solar cells (alloy-base amorphous materials, PIN layers, strains in the interface, and effects of impurities); Taiyoko hatsuden system jitsuyoka no tame no kaiseki hyoka. Usumaku taiyo denchi jitsuyoka no tame no kaiseki hyoka (gokinkei amorphous zairyo pin kakuso kaimen ni okeru yugami fujunbutsu nado no eikyo)

Energy Technology Data Exchange (ETDEWEB)

Matsuda, A; Oeda, H; Yamasaki, S; Hata, N; Kondo, M; Toshima, Y; Sakata, I; Ganguly, G; Suzuki, A; Kamei, T; Okushi, H; Nonaka, H; Oda, N; Katagiri, H; Ichimura, N; Kokubu, K; Nakamura, K; Sekikawa, T; Yamanaka, M [Electrotechnical Laboratory, Tsukuba (Japan)

1994-12-01

Described herein are the results of the FY1994 research program for analysis and evaluation for thin film solar cells. The study on quantitative analysis of hydrogen atoms in a plasma determines quantity of hydrogen atoms in the plasma of monosilane diluted with hydrogen. It is found, contrary to expectation, that quantity of hydrogen atoms in the plasma decreases as it is more diluted with hydrogen. The study on light-induced degradation of the thin chlorine-base amorphous silicon films confirms that the plasma CVD method with 20% of dichlorosilane gas added to monosilane gas produces the thin amorphous silicon film 3 times faster than the conventional method. The thin film has essentially the same defect density as the one prepared by the conventional method, showing good photoelectric characteristics. The thin film of chlorinated amorphous silicon has a 1 digit lower defect density than the conventional one of amorphous silicon, as revealed by the accelerated degradation test with irradiated laser light and the constant current method to determine saturated defect density. 3 figs.

FY 2000 report on the results of the R and D of the prediction technology for environmental effects of CO2 ocean sequestration. Ocean survey and development of the assessment technology for capacity of CO2 sequestration; 2000 nendo nisanka tanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu seika hokokusho. Kaiyo chosa oyobi CO2 kakuri noryoku hyoka gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Assuming the dissolution/sequestration of CO2 at the medium-depth sea area around Japan (depth: 1,000-2,000m), the development was being proceeded with of the assessment technology for capacity of CO2 ocean sequestration and the prediction technology of environmental effects at the point of CO2 discharge. In FY 2000, conducted were the ocean survey and the development of assessment technology for CO2 sequestration capacity. In the investigational study, the following three were carried out: 1) survey/observation of the flow field on the line of 165 degrees of east longitude, and acquisition of various data such as the distribution of carbonic acid base substances and the speed of carbon transport; 2) study of the amount of existence of organisms and kind/composition of the medium-depth plankton at the typical observation points; 3) test/experiment actually conducted in the sea area for the experimental equipment for CaCO3 dissolution experimental equipment for studying interactions between the CO2 and CaCO3 dissolved into the medium-depth sea. As to the development of the assessment technology, carried out were the heightening of accuracy of medium-depth ocean circulation models using the inverse method already developed and the estimation of the flow field using the observation data. At the same time, the estimation of the flow field, etc. were conducted using large circulation ocean models. (NEDO)

Report on achievements in fiscal 1998. Research and development of a technology to forecast environmental effect in association with isolation of carbon dioxide in oceans. Ocean surveys and development of a technology to evaluate CO2 separation capability; 1998 nendo nisanka tanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu seika hokokusho. Kaiyo chosa oyobi CO{sub 2} kakuri noryoku hyoka gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Assuming that CO2 is dissolved and separated in the middle layer in a sea area around Japan, ocean surveys were carried out to acquire fundamental data required for development of a technology to evaluate CO2 separation capability of ocean, and for development of a technology to forecast environmental effect. In addition, using the western part of the Pacific Ocean as the object, development was performed on a numerical model to forecast behavior of CO2 in ocean in the scale of several ten years to several hundred years, and evaluate capability of CO2 separation from atmosphere. The research and development items for the current fiscal year are as follows: (1) ocean surveys, (2) model development, and (3) surveys and studies required for the ocean surveys and experiments. The survey voyage for item (1) was executed centering on the courses of traverse on 140 degree line of east longitude and 147 degree line of east longitude. The voyage surveyed densities of sea water, such data as chemical tracers, discharged mid-layer neutral buoys, carbonic acid based substances, marine living organisms, and sedimentary particles. For item (2), trial calculations were performed by using an inverse model to estimate structures of ocean flows, and discussions were given to enhance the accuracy. For item (3), design and fabrication were carried out on an equipment to experiment on-site dissolution of calcium carbonate, and a chamber for on-site experiments at deep sea bottom. (NEDO)

Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the application technology of functional protein complex (R and D of the high-functional maintenance technology for power plants); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Kinosei tanpakushitsu shugotai oyo gijutsu no kenkyu kaihatsu (hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

In order to develop advanced maintenance technology for power generation facilities, application technology of functional protein complexes is under investigation. On a light controllable enzymatic reaction system, construction of a light controllable bio-reactor by physico-chemical and bio- chemical techniques, and structure and functions of a photosynthetic protein complex using thermophilic cyanobacteria as material are under investigation. On a molecular mechanism for recognition and reaction of receptor proteins, structure analysis and engineering application of glutamate receptor channels of a synaptic transmission system, and basic study and material proteins for artificial structures using endocytic micromachinery, and a multi-enzyme system for synthesis of glycosphingolipids are under investigation. On a complex oxidation/reduction system by genetic engineering technique, construction of a high- efficiency stable system with functionally arranged oxidoreductase and electron transmission systems in biomembranes is in promotion. Research work was also made on molecular assemblies for a functional protein system. 166 refs., 91 figs., 9 tabs.

Fiscal 1997 R an D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules (high-efficiency and analysis and manipulation technology for DNA); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (DNA nado kokoritsu kaiseki sosa gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). Through the observation of super spiral DNA fixed on a spermin or spermidine treated mica substrate by AFM (atomic force microscope), fixation of DNA without any deformation in solution was clarified, and visualization of the spiral structure of DNA were successfully achieved. Manipulation of Xe atoms adsorbed on an Si(111) surface was certainly possible by using STM (scanning tunneling microscope)/atom probe equipment. A nucleation mechanism in crystal growth was studied for various organic source-molecules/GaAs(001) surface systems, and formation of high-density nuclei on the GaAs surface was achieved by accelerating the translational energy of Ga material molecules up to 6eV or more. Ziegler- Natta catalysis important for industrial polymerization of olefin molecules was precisely analyzed by first-principle dynamic simulation. A large-scale simulation of zeolite catalyst is also in promotion for methanol to gasoline conversion. 51 refs., 87 figs., 7 tabs.

Advanced research and development of gas hydrate resources. R and D of exploration and others - R and D of excavation technologies and others - surveys/researches on methods of evaluating environmental effects - surveys/researches on application systems; Gas hydrate shigenka gijutsu sendo kenkyu kaihatsu. Tansa nado ni kansuru kenkyu kaihatsu / kussaku gijutsu nado ni kansuru kenkyu kaihatsu / kankyo eikyo hyokaho no chosa kenkyu / riyo system ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Gas hydrate is a clathrate compound in a gaseous molecule as the host, stable under relatively mild environments. It is deposited in the 600m or deeper sea bottoms to form the gas hydrate deposit and massively occurring in the sea areas around Japan. This deposit has been studied viewed from natural gas resources, causes for natural hazards and contribution to the global warming. This project excavates a well in the deposit, to study possibilities of the technologies for decomposing, fluidizing and lifting the hydrate as the gas source, and for establishing the natural gas transporting/mooring systems in which its characteristics are utilized. The R and D activities are directed to the 4 areas, (1) development of the exploration technologies to determine the deposit sea area, quantity and conditions, (2) development of the stable well-excavation technologies, (3) studies on the effects of gas production on the environments, and development of the system for predicting the effects, (4) and studies on the application systems. The item (3) finds out the transportation/storage system possibly more economical than the current freezing/liquefaction technologies. The item (3) has the development themes of evaluating the geohazards caused by excavation and gas production, and their effects on the ecological systems. (NEDO)

FY 1998 annual report on the preliminary research and development of techniques for developing resources from gas-hydrate. Studies on gas-hydrate exploration, excavation techniques, methods for assessing environmental impacts, and gas hydrate handling systems; 1998 nendo gas hydrate shigenka gijutsu sendoken kaihatsu seika hokokusho. Tansanado ni kansuru kenkyu kaihatsu, kussaku gijutsu nado ni kansuru kenkyu kaihatsu, kankyo eikyo hyokaho no kenkyu kaihatsu, riyo system ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This R and D project is for the preliminary studies on development of the following 4 types of techniques for developing resources from gas-hydrates (GH): (1) gas-hydrate exploration, (2) excavation techniques, (3) methods for assessing environmental impacts, and (4) gas hydrate handling systems. The FY 1988 R and D results are described. For gas-hydrate exploration, the methods for analyzing inorganic ions and trace quantities of elements, which are necessary for accurately estimating the offshore GH around Japan, are established; and case studies are conducted for methods of predicting GH deposit forming mechanisms, and stability fields of GH, based on terrestrial heat flow and seismic data. For excavation techniques, GH decomposition rate is analyzed using a laboratory system which reproduces conditions of excavation of GH layers. For methods for assessing environmental impacts, a geo-hazard predicting model is established, to study ground displacement and gas leakage sensing systems and data transmission systems to cope with the hazards. For gas hydrate handling systems, an overall system is studied, and storage and transportation systems are outlined. (NEDO)

Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the technology of accelerated formation of bio-functions (R and D of the technology of creation of novel advanced enzymes); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kasokugata seibutsu kino kochiku gijutsu no kenkyu kaihatsu (shingata kokino koso sosei gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes R and D on creation technique of novel advanced enzymes. In fiscal 1997, a novel mutagenesis technique was developed to obtain more kinds of mutational genes by shuffling between clonal genes as compared with the previous homogeneous recombination. A genotype- and phenotype-linking technology was developed by expressing random motifs (peptide as components of the active site of protein) on bacteria, and by developing a single-motif protein library. Study was made on a selection system for functional molecules of catalytic activities in a gene level, and a selection system for function of signal transduction. Analysis and evaluation study on vitro experimental technology can be efficiently promoted by recognizing the fitness landscape of target protein molecules. As a result, instead of the conventional method which needs several cycles of mutation and screening of 3-4 week/cycle, an efficient method possible to obtain multiple mutants was established. Research work was also promoted by various organizations to develop an accelerated formation technology of bio-functions. 68 refs., 51 figs., 14 tabs.

Fiscal 1996 project on the modeling for effective energy consumption in developing countries under a consignment from NEDO. Recent on the results of the demonstrative study on scrap preheater of electric furnace in the iron making process (for public); 1996 nendo hatten tojokoku energy shohi koritsuka model jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Seitetsu katei ni okeru denkiro no genryo yonetsu sochi ni kakawaru jissho kenkyu seika hokokusho (kokaiyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Indonesia is the biggest iron steel producing country in the ASEAN countries. Most of the production is produced by the electric furnace method in which iron steel scrap is used as a material. However, an energy saving measure in this method, the electric furnace scrap preheater using flue gas, has not yet been spread on a full scale. This R and D is aimed at developing jointly with Indonesia an electric furnace scrap preheater for medium/small size electric furnaces which are adoptable to the present iron making situation in Indonesia and installing it to the electric furnace of the iron making plant in Indonesia for a demonstrative study on energy saving, etc. Spread/expansion of the electric furnace scrap preheater which is an excellent energy saving system targeted expansion of energy saving technology not only of Indonesia, but of ASEAN countries and Japan. In this fiscal year, remodeling of part of the system was made by change of flue gas flow for increasing the energy saving effect, and at the same time, a research study was made of a scrap reheater effective as a total system. Moreover, the paper investigated technical data/information in Japan and overseas. 3 figs., 9 tabs.

Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of new software structuring models (R and D of micromachine cooperative control use software); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Shin software kozoka model no kenkyu kaihatsu (bisho kikai kyocho seigyoyo software no kenkyu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

A R and D was conducted of software structuring models which ease the development and maintenance of software systems and meet diversification of needs. As for the study of the cooperative control use programming language, a R and D of agent oriented language Flage was carried out for expansion of language function, arrangement of network function, development of exercises, etc. As to the formulation of agent knowledge, proposed were processes to make a program from the specifications, and EVA, a mechanism in response to changes in the specifications of existing programs. In relation to the basic theory of cooperation system, a study was made mainly of object oriented attribute grammar OOAG as a model representing cooperative computation in software process as a rule group. Concerning the study of the situation recognition mechanism, researched were models of communication and reasoning among agents in cooperation. 187 refs., 107 figs., 23 tabs.

Fiscal 1999 research report. Basic research for promotion of joint implementation programs (Comprehensive feasibility study on efficiency improvement of heat generation facility and heat network for district heating at middle and small cities in Moscow region, the Russian Federation - 2 model cities within the region); 1999 nendo Russia renpo Moscow shunai chusho toshi ni okeru chiiki danboyo netsu kyokyu shisetsu yusomo no koritsu kaizen keikaku sogo chosa hokokusho. Shunai 2 toshi wo model to suru

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The above-named effort aims to work out modification plans and to predict their energy saving, energy substituting, and greenhouse gas reduction effects, and thereby to scout out a project which will effectively utilize flexibility-ensuring 'joint implementation' for the attainment of greenhouse gas reduction levels defined at COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change). The results of assessment of this project based on the outcome of the survey show that (1) there is necessity for the project and that the presence of needs to be urgently satisfied is clear, that (2) energy saving, energy substituting, and greenhouse gas reduction effects are proved to exist and that the project is therefore an appropriate candidate for an activity to be implemented jointly, that (3) Russian agencies concerned are strongly interested in the project and that a sufficiently cooperative system will be available toward implementation, and that (4) there is an extremely large room for energy saving in the district heating oriented heat supply business in Russia and that probabilities are quite high that natural gas-fired turbine cogeneration plants capable of improving overall energy efficiency will enjoy extensive diffusion. (NEDO)

Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules (R and D of the formation of advanced materials for power generation environment); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (hatsuden kankyoyo kokino sozai keisei gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). Ten nanoscale Ge islands were successfully formed in proper positions on an Si substrate surface by using mask technology of nanoscale atomic layers. Growth of less-defect ZnSe films on a GaAs(110) surface was possible under various conditions. The magnetic transfer mechanism of Mn oxide with huge reluctance was clarified. Through study on selective-area deposition of Si on plasma-oxidized ultrathin SiO2 mask layers patterned by direct electron-beam exposure and an idea of SiO2/SiNx bilayer mask, direct use of the ultrathin mask layer as insulating layer in device structure was achieved. The superior property as electron beam resist of methano- fullerene composed of fullerene C60 with side chains including oxygen was clarified. The initial oxidation process of an Si(100) surface was analyzed, and the observation result by SREM was theoretically explained. Development of a high-resolution spin polarization electron microscope was also mentioned. 48 refs., 145 figs., 20 tabs.

Fiscal 1997 result of the R and D project of industrial science and technology under consignment from NEDO. R and D of creation technology of original advanced materials (R and D of creation technology of original advanced materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo (Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku). Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes R and D of creation technology of original advanced materials in the R and D project of industrial science and technology. Although new material technology is dependent on the needs of a future society, it should correspond to a global environment preservation society, information-oriented society and aging society as observed based on the present social trend, and new materials superior in hot strength, light weight, corrosion resistance, decomposability, photo-function, magnetism, conductivity, bio-copying and adaptability are demanded. This project is in promotion since fiscal 1996 to develop formation technology of high-performance advanced new materials by precise molecular control of structure and production process of organic polymers and molecular assemblies. The research started on 4 themes such as advanced stimulus-response material, precision catalytic polymerization, condensed system structure control and multi-dimensional polymer structure. The research on molecule harmonizing material was added in fiscal 1997. In fiscal 1997, the general committee discussed a progress situation and next year research plan, and surveyed an overseas technology trend. 1 fig.

Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of materials to heighten efficiency of power generation facilities); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (hatsuden shisetsuyo koseinoka zairyo gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper described the fiscal 1997 results of the study of the condensation base precise structure control conducted as a technical development of materials to heighten efficiency of power generation facilities. Condensation base polymer is an important material which occupies most of the engineering plastics. The study is aimed at developing basic technologies on the molecular weight and regularity by which a remarkable improvement can be expected in performance of condensation polymerization/ring-opening polymerization polymer materials, polymerization catalyst which arbitarily controls the primary structure such as branch and end group structures, and development of the precision polymerization process. In the synthesis of ordered polymer by direct polycondensation, synthesis of ordered polyamide from asymmetric monomers is studied. In the synthesis of chemically selective polyamide by direct polymerization, polyamide with functional group is synthesized by polymerizing without protecting functional group the monomer with such functional group as causes side reaction in polymerization. In the synthesis of polyamide having the limited distribution of molecular weight, the molecular weight/distribution of polyamide are controlled by connectedly conducting polycondensation which is itself to be done successively. 91 refs., 72 figs., 43 tabs.

Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (development of precise structure control materials for enhancement of oil refining); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (sekiyu seisei kodoka seimitsu kozo seigyo zairyo kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper described the R and D of technologies for creating original high-functional materials under the R and D system of industrial scientific technology. Japan chemical Innovation Institute (JCII) is conducting intensive joint researches under consignment from NEDO with private companies, universities and national research institutes. Among those, the paper reported the fiscal 1997 results of the following two researches conducted as development of precise structure control materials for enhancement of oil refining: precision catalytic polymerization and multi-dimensional space polymer. As to the precision catalytic polymerization, the paper is aimed at developing base technologies for the molecular weight and stereoregularity by which remarkable improvement in performance of addition polymerization type polymer can be expected, and on the development of a polymerization catalyst which arbitarily controls the primary structure such as end group structure and of a precision addition polymerization process. Subthemes are addition polymerization with limit and oriented catalytic polymerization. In relation to multi-dimensional space polymer, the paper is aimed at developing highly selective polymerization technology of aromatic compounds using enzyme related catalysts and synthesis technology of regular structure polymer, and synthesis technology of new polymer group having a new chain pattern except covalent bond/new polymer group having characteristics in three-dimensional space geometric structure. 244 refs,, 160 figs., 94 tabs.

Fiscal 1996 result reports of the researches under consignment from NEDO. Developments of fuel cell technology, polymer electrolyte fuel cell, fuel cell power generation system technology, and high-voltage type several tens kW class distributed power source system; Shin energy sangyo gijutsu sogo kaihatsu kiko itaku gyomu 1996 nendo seika hokokusho. Nenryo denchi gijutsu kaihatsu, kotai kobunshigata nenryo denchi no kenkyu kaihatsu, hatsuden system gijutsu kaihatsu, koden`atsugata suju kW kyu bunsan dengen system no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This paper precisely reports the research result on development of fuel cell technology in fiscal 1996. On verification of cell durability, the cell test result in hydrogen including CO of 100ppm using Pt-Ru catalyst as CO resistant catalyst showed that the loss percent of cell voltage decreases with an increase in Ru content. On development of stack technology, the carbon humidification plate superior in chemical stability was developed as one of the parts for layered stacks. The separator with a water- permeable carbon plate and serpentine flow fields was fabricated for highly layered stacks, and achieved the target performance in single cell power generation test. On establishment of design basis for compact fuel processor, the bench-scale test was conducted of Ru/{gamma}-Al2O3 and Pt-Ru/{gamma}-Al2O3 catalysts as advanced CO selective oxidation catalyst for CO reducers. On demonstration test for the several tens kW class stationary power plant, the system configuration of power generation plants using natural gas as fuel was studied. 106 figs., 38 tabs.

Report on the achievements in fiscal 1999. Technology to use gas hydrate as a resource (Research and development for exploration, research and development on drilling technologies, investigative research on an environment influence evaluation method, and investigative research on a utilization system); 1999 nendo gas hydrate shigenka gijutsu sendo kenkyu kaihatsu seika hokokusho. Tansa nado ni kansuru kenkyu kaihatsu, kussaku gijutsu nado ni kansuru kenkyu kaihatsu, kankyo eikyo hyokaho no chosa kenkyu, riyo system ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The contents of the research and development performed in the current fiscal year are as follows: (1) research and development for exploration, (2) research and development on drilling technologies, (3) investigative research on an environment influence evaluation method, and (4) investigative research on a utilization system. In Item (1), element analysis data are used to study a method to estimate production environment of hydrate ore beds by using an inorganic ion analyzer and a trace amount element analyzer, the crust thermal flow measuring method is used to discuss a method to analyze the hydrate stability zones together with the data of sea area exploration records, and conceptual design is made on a resource potential evaluation system. In Item (2), experiments and analytical discussions are performed on decomposition control of the gas hydrate solid-liquid interface according to such conditions for the drilling fluid as temperatures and flow rates. Elucidation is given on the initial process of bubble generation for behavior of decomposed gas bubbles. Observation and elucidation are made on two-phase flow behavior of non-Newtonian fluid. In Item (3), conceptual design is carried out on a system to detect elements of shape change in each bed due to fluid movement in a gas hydrate bed and an upper bed. In Item (4), discussions are given on the optimizing conditions for generation and dissociation of gas hydrates. Investigation is made also on a possibility of the transportation and storage system. (NEDO)

EDITORIAL: Focus on Cold and Ultracold Molecules FOCUS ON COLD AND ULTRACOLD MOLECULES

Science.gov (United States)

Carr, Lincoln D.; Ye, Jun

2009-05-01

öhlich, A Griesmaier, T Pfau, H Saito, Y Kawaguchi and M Ueda High-energy-resolution molecular beams for cold collision studies L P Parazzoli, N Fitch, D S Lobser and H J Lewandowski Collisional effects in the formation of cold guided beams of polar molecules M Motsch, C Sommer, M Zeppenfeld, L D van Buuren, P W H Pinkse and G Rempe Towards sympathetic cooling of large molecules: cold collisions between benzene and rare gas atoms P Barletta, J Tennyson and P F Barker Efficient formation of ground-state ultracold molecules via STIRAP from the continuum at a Feshbach resonance Elena Kuznetsova, Marko Gacesa, Philippe Pellegrini, Susanne F Yelin and Robin Côté Emergent timescales in entangled quantum dynamics of ultracold molecules in optical lattices M L Wall and L D Carr Rotational state resolved photodissociation spectroscopy of translationally and vibrationally cold MgH+ ions: toward rotational cooling of molecular ions K Højbjerre, A K Hansen, P S Skyt, P F Staanum and M Drewsen Collective transverse cavity cooling of a dense molecular beam Thomas Salzburger and Helmut Ritsch A Stark decelerator on a chip Samuel A Meek, Horst Conrad and Gerard Meijer Deceleration of molecules by dipole force potential: a numerical simulation Susumu Kuma and Takamasa Momose Ultracold molecules: vehicles to scalable quantum information processing Kathy-Anne Brickman Soderberg, Nathan Gemelke and Cheng Chin Magnetic field modification of ultracold molecule-molecule collisions T V Tscherbul, Yu V Suleimanov, V Aquilanti and R V Krems Spectroscopy of 39K85Rb triplet excited states using ultracold a 3Σ+ state molecules formed by photoassociation J T Kim, D Wang, E E Eyler, P L Gould and W C Stwalley Pumping vortex into a Bose-Einstein condensate of heteronuclear molecules Z F Xu, R Q Wang and L You Intense atomic and molecular beams via neon buffer-gas cooling David Patterson, Julia Rasmussen and John M Doyle Dynamical properties of dipolar Fermi gases T Sogo, L He, T Miyakawa, S Yi, H Lu

Fiscal 1997 project on the R and D of industrial scientific technology under consignment form NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of structure control materials / R and D of molecular harmonized materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) bunshi kyocho zairyo no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

By establishing microtechnology using molecular-level bottoming-up (molecular harmonization) by imitating the system of living organism, the paper described the R and D of molecular harmonized materials aiming at developing high-functional/high-performance materials such as high-performance catalyst, photo-information functional materials and sensing materials. Under consignment from NEDO, Japan Chemical innovation Institute started the 5-year plan in fiscal 1997. Self-assembled molecular films, in which organic molecules are orderly arranged by self-assembly, aim at developing new memory/optical/sensing materials. Mesophase materials which are such materials as liquid crystal showing the intermediate state between solid and liquid, develop optical/photoconductive materials using precise molecular orientation controllability. Macroporous materials are such substances as zeolite having molecular size micro pores. The paper aims at establishment of synthesis techniques of them and development of high-performance catalyst, etc. using them. In the comprehensive investigational research, conducted was a survey of the trend overseas in addition to a study of subjects in question. Further, the supporting basic study was reconsigned to universities, etc. 57 refs., 62 figs., 17 tabs.

FY 1999 report on the results of the R and D project on the industrial technology for the global environment. R and D of the prediction technology of environmental effects brought by CO2 ocean sequestration (Ocean survey and development of evaluation technology for CO2 sequestration ability); 1999 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo NEDO seika hokokusho. Nisankatanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu (Kaiyo chosa oyobi CO2 kakuri noryoku hyoka gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Assuming the melting and sequestration of CO2 at the intermediate depth of the sea area around Japan, study of evaluation technology of CO2 sequestration ability in ocean was studied, and the FY 1999 results were summed up. In the ocean survey, survey was conducted by ship (No.2 Hakurei-maru) mainly at typical observation points and traverse lines of long. 147 E and long. 155 E. In the survey, the following data were acquired: data on seawater density and chemical tracer, data on release of intermediate-depth/independent buoys, concentration distribution of carbonic acid base substances/nutrient salts/chlorophyll, data on the existing amount of marine organisms and primary production speed measurement experiment, data on experiment on CO2 on-board exposure to organisms in the intermediate depth of ocean, etc. In the measurement/analysis of the sediment particle flux amount, sediment traps were installed/recovered. Further, for the purpose of measuring the neutralizing effect of calcium carbonate, operation test on CaCO{sub 3} melting experimental equipment was conducted in the actual sea area. In the development of a model for evaluation of CO2 sequestration ability, carried out were the improvement of the model using the inverse method, study of the estimated accuracy using the ocean observation data, etc. (NEDO)

Achievement report for fiscal 1997 on the research and development to lead to gas hydrate using technology. Research and development on exploration, research and development on drilling technologies, survey and research on a method to evaluate environmental impact, and survey and research on a utilization system; 1997 nendo gas haidoreto shigenka gijutsu sendo kenkyu kaihatsu seika hokokusho. Tansanado ni kansuru kenkyu kaihatsu, kussaku gijutsu ni kansuru kenkyu kaihatsu, kankyo eikyo hyokaho no chosa kenkyu, riyo system ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-09-01

The present study is intended to analyze comprehensively geophysical, geological and geochemical data, and establish a technology to estimate distribution of gas hydrate (GH) in sea areas around Japan. It is also intended to develop a high-accuracy resource amount calculating method utilizing the result of excavation of GH planned in the future. In order to achieve these goals, the following activities are performed: (1) study on a method to estimate production environment of GH deposits, (2) development of a method to estimate GH stability areas by using the crust thermal flow measuring method, and (3) study on estimation of GH distribution and wide-area potential. For the study (1), an inorganic element analyzer was introduced, and calibration of devices was performed in fiscal 1997. A survey was carried out on literatures related to distribution of inorganic elements and process of GH deposit production. In the study (2), design and trial fabrication were executed on a high-accuracy crust thermal flow measuring device, capable of long-term continuous observation. In the study (3), re-processing focusing on BSR was implemented by using the latest computer and analysis software on the data in which BSR has been confirmed in the surveys done in the past on sea areas around Japan. (NEDO)

Achievement report for fiscal 1995 on the research and development of comprehensive basic technologies on marine resources (manganese nodule mining system) in industrial and scientific technology research and development project. Trends and forecasts of the supply-demand for metal resources (Ni, Co, Cu, Fe, Mn) that are contained in manganese nodules; 1995 nendo kaiyo shigen sogo kiban gijutsu no kenkyu kaihatsu (mangan dankai saiko system) seika hokokusho. Mangan dankai ni kakawaru kinzoku shigen (Ni, Co, Cu, Fe, Mn) no kyokyu ni kansuru shorai doko no suitei

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-12-01

Living standards improving in developing countries especially in China are the most influential factor to determine the demand for Cu. Consumption of Ni will depend on the trends of advanced technologies such as Ni-hydrogen battery, fuel cell, shape memory alloy, hydrogen absorbing alloy, in addition to increase in global population and developing countries' living standards improvement. Co is far more dependent on advanced technologies than Ni is. On the land, Ni ore is increasingly lower in quality and Co is being retrieved from by-products of Cu production, both meeting the problem of unstable supply. Consideration is made to apply new extraction methods to Cu production; there are some potential resources for Fe and Mn. The Mn nodule exists in great quantities and is a attractive source of supply, but a long time will be required before it is exploited. It is necessary to speed up the study to exploit the Mn nodule, but first of all the problem of its competition with land resources in terms of cost has to be solved. It needs to be found out at what stage of production the Mn nodule is competitive with land products. In any case, Japan should undertake the efforts of marine resources exploitation leading other countries of the world. (NEDO)

Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of structure control materials / R and D of multi-stimuli-responsive materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) kodo shigeki oto zairyo no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper described multi-stimuli-responsive materials out of the technology developments for creating original high-functional materials under the system of R and D of industrial scientific technologies. These are materials which repeatedly reproduce functions such as separation, penetration and movement in response to stimuli by imitating living organisms. In relation to polymer multi-stimuli-responsive materials, various copolymers were synthesized using N-acetyl (meta) acrylamide, of which the synthesis method was established in the previous fiscal year, as a main component, and thermal responsive polymer with upper critical solution temperature which becomes a base of separation functional materials was searched for. By immobilizing it with molecular recognition ligand, measured was thermal dependence of affinity of the immobilized matter to albumin. Also studied were molecular recognition cell adhesion/separation functional materials. Concerning composite multi-stimuli-responsive materials, with the use of silica microcapsule surface-immobilized with silane coupling agent, studied were the optimum conditions for immobilizing thermo-responsive polymer to the surface of the capsule. Using motion functional materials by ion exchange resin, obtained was motion functionality which is satisfactory at the state of practical use. 94 refs., 82 figs., 16 tabs.

Industrial and scientific technology research and development project fiscal 1997 commissioned by the New Energy and Industrial Technology Development Organization. Report on research and development of a brain type computer architecture `trial fabrication and high-level evaluation on chips for a large-scale artificial neural system` and on results of evaluation studies on the chips; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Nogata computer architecture no kenkyu kaihatsu `daikibo jinko shinkei kairo system yo chip no shisaku to kodo hyoka` chip hyoka kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

In order to develop a brain type computer architecture, a brain mimic processor (BMP) has been developed (which was made in LSI in fiscal 1997), and studies are being made on developing its applications. Development has been made on an element in which linkage of one million cells with one thousand neural cells can be realized. Evaluation substrates mounted with the BMP, control software, and compilers were provided to 15 organizations including the National Research Institutes, universities, corporations, and other societies (for 19 themes) to evaluate capability of the LSI and its application development. All of the research organizations are using these items utilizing features of the LSI or the network for such purposes as learning, storage, recognition and control. The applicable theme may include infrared spectrum pattern recognition and domain division of document images using neural network functions. It can also include structural analysis of mass spectrum molecules, time series pattern recognition, location of corresponding points in images, estimation of moving images, satellite control, character recognition, short time storage, long-term association memory models, and invention process studies, all utilizing the functions of the BMP. 71 refs., 89 figs., 9 tabs.