40 CFR 81.51 - Portland Interstate Air Quality Control Region.

Science.gov (United States)

2010-07-01

... Quality Control Regions § 81.51 Portland Interstate Air Quality Control Region. The Portland Interstate Air Quality Control Region (Oregon-Washington) has been revised to consist of the territorial area... Portland Interstate Air Quality Control Region (Oregon-Washington) will be referred to by Washington...

Comparison of the physical and mechanical properties of MTA and portland cement.

Science.gov (United States)

Islam, Intekhab; Chng, Hui Kheng; Yap, Adrian U Jin

2006-03-01

This study evaluated and compared the pH, radiopacity, setting time, solubility, dimensional change, and compressive strength of ProRoot MTA (PMTA), ProRoot MTA (tooth colored formula) (WMTA), white Portland cement (WP), and ordinary Portland cement (OP). The results showed that PMTA and Portland cement have very similar physical properties. However, the radiopacity of Portland cement is much lower than that of PMTA. The compressive strength of PMTA was greater than Portland cement at 28 days. The major constituent of PMTA is Portland cement. Given the low cost of Portland cement and similar properties when compared to PMTA, it is reasonable to consider Portland cement as a possible substitute for PMTA in endodontic applications. However, industrially manufactured Portland cement is not approved currently for use in the United States and therefore no clinical recommendation can be made for its use in the human body. Further in vitro and in vivo tests, especially with regards its biocompatibility, should be conducted to ascertain if it meets the FDA requirements for use as a medical device.

Radiopacity of portland cement associated with different radiopacifying agents.

Science.gov (United States)

Húngaro Duarte, Marco Antonio; de Oliveira El Kadre, Guâniara D'arc; Vivan, Rodrigo Ricci; Guerreiro Tanomaru, Juliane Maria; Tanomaru Filho, Mário; de Moraes, Ivaldo Gomes

2009-05-01

This study evaluated the radiopacity of Portland cement associated with the following radiopacifying agents: bismuth oxide, zinc oxide, lead oxide, bismuth subnitrate, bismuth carbonate, barium sulfate, iodoform, calcium tungstate, and zirconium oxide. A ratio of 20% radiopacifier and 80% white Portland cement by weight was used for analysis. Pure Portland cement and dentin served as controls. Cement/radiopacifier and dentin disc-shaped specimens were fabricated, and radiopacity testing was performed according to the ISO 6876/2001 standard for dental root sealing materials. Using Insight occlusal films, the specimens were radiographed near to a graduated aluminum stepwedge varying from 2 to 16 mm in thickness. The radiographs were digitized and radiopacity compared with the aluminum stepwedge using Digora software (Orion Corporation Soredex, Helsinki, Finland). The radiographic density data were converted into mmAl and analyzed statistically by analysis of variance and Tukey-Kramer test (alpha = 0.05). The radiopacity of pure Portland cement was significantly lower (p cement/radiopacifier mixtures were significantly more radiopaque than dentin and Portland cement alone (p cement/bismuth oxide and Portland cement/lead oxide presented the highest radiopacity values and differed significantly from the other materials (p cement/zinc oxide presented the lowest radiopacity values of all mixtures (p cement as radiopacifying agents. However, the possible interference of the radiopacifiers with the setting chemistry, biocompatibility, and physical properties of the Portland cement should be further investigated before any clinical recommendation can be done.

Microstructure and durability of Portland cement-carbon nanotube composites

OpenAIRE

MacLeod, Alastair James Neil

2017-01-01

The incorporation of carbon nanotubes (CNTs), fibres with diameters less than 100 nanometres that exhibit a tensile strength in excess of ten times greater than steel, into Portland cement (OPC) is a relatively novel, yet promising, development for next-generation construction materials exhibiting enhanced strength and ductility, even multifunctionality. When added to Portland cement, creating a Portland cement-CNT nanocomposite material (OPC-CNT), CNTs promote the nucleation of the princi...

76 FR 28315 - Security Zone; Portland Rose Festival on Willamette River

Science.gov (United States)

2011-05-17

... Zone; Portland Rose Festival on Willamette River AGENCY: Coast Guard, DHS. ACTION: Notice of enforcement of regulation. SUMMARY: The Coast Guard will enforce the Portland Rose Festival Security Zone in... River during the Portland Rose festival. During the enforcement period, no person or vessel may enter or...

Preterm delivery among people living around Portland cement plants

International Nuclear Information System (INIS)

Yang, C.-Y.; Chang, C.-C.; Tsai, S.-S.; Huang, H.-Y.; Ho, C.-K.; Wu, T.-N.; Sung, F.-C.

2003-01-01

The Portland cement industry is the main source of particulate air pollution in Kaohsiung city. Data in this study concern outdoor air pollution and the health of individuals living in communities in close proximity to Portland cement plants. The prevalence of delivery of preterm birth infants as significantly higher in mothers living within 0-2 km of a Portland cement plant than in mothers living within 2-4 km. After controlling for several possible confounders (including maternal age, season, marital status, maternal education, and infant sex), the adjusted odds ratio was 1.30 (95% I=1.09-1.54) for the delivery of preterm infants for mothers living close to he Portland cement plants, chosen at the start to be from 0 to 2 km. These data provide further support for the hypothesis that air pollution can affect he outcome of pregnancy

Synthesis of pure Portland cement phases

DEFF Research Database (Denmark)

Wesselsky, Andreas; Jensen, Ole Mejlhede

2009-01-01

Pure phases commonly found in Portland cement clinkers are often used to test cement hydration behaviour in simplified experimental conditions. The synthesis of these phases is covered in this paper, starting with a description of phase relations and possible polymorphs of the four main phases...... in Portland cement, i.e. tricalcium silicate, dicalcium silicate, tricalcium aluminate and tetracalcium alumino ferrite. Details of the The process of solid state synthesis are is described in general including practical advice on equipment and techniques. Finally In addition, some exemplary mix compositions...

OHSU web site readers have access to distinctive information. How to e-mail a child in the hospital; where to find a midwife.

Science.gov (United States)

Botvin, Judith D

2005-01-01

Oregon Health & Science University (OHSU), Portland, Ore., posts a web site which generously covers the various aspects of this complex organization. Visitors to www.osuhealth.com, can find a midwife, send an email to a child in the hospital, and learn about the benefits of living in Oregon.

Analyses of heavy metals in mineral trioxide aggregate and Portland cement.

Science.gov (United States)

Schembri, Matthew; Peplow, George; Camilleri, Josette

2010-07-01

Portland cement is used in the construction industry as a binder in concrete. It is manufactured from chalk, limestone, and clay, which are clinkered at very high temperatures and ground with gypsum to form Portland cement. The raw materials and the manufacturing process can result in the inclusion of heavy metals in Portland cement. Portland cement with a four to one addition of bismuth oxide is marketed as mineral trioxide aggregate (MTA), which is used mainly as a dental material. Heavy metal inclusion can be of concern because MTA is in contact with hard and soft tissues. Measurements of arsenic, lead, and chromium in hydrated gray and white Portland cement, ProRoot MTA, and MTA Angelus were conducted with graphite furnace atomic absorption spectrophotometry after acid digestion on the hydrated material. The leaching of the metal ions from the solid material in water and simulated body fluid (SBF) was also determined. All cement types showed high relative values of leached chromium compared with arsenic and lead in both the total metal content and leached species. The gray Portland cement showed the highest total amount of metal. The white Portland and both MTAs had lower values for all the leached metal ions. Both MTAs released more arsenic than the amount specified in ISO 9917-1 (2007). Portland cements and MTAs showed evidence of heavy metals in the acid-soluble form as well as leaching in deionized water and SBF. MTA contained levels of arsenic higher than the safe limit specified by the ISO 9917-1 (2007). Copyright 2010 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Effect of blended materials on U(VI) retention characteristics for portland cement solidification product

International Nuclear Information System (INIS)

Tan Hongbin; Ma Xiaoling; Li Yuxiang

2006-01-01

Using the simulated groundwater as leaching liquid, the retention capability of U(VI) in solidification products with Portland cement, the Portland cement containing silica fume, the Portland cement containing metakaolin and the Portland cement containing fly ash was researched by leaching experiments at 25 degree C for 42 d. The results indicate silica fume and metakaolin as blended materials can improve the U(VI) retention capability of Portland cement solidification product, but fly ash can not. (authors)

76 FR 28318 - National Emission Standards for Hazardous Air Pollutants From the Portland Cement Manufacturing...

Science.gov (United States)

2011-05-17

... Cement Manufacturing Industry and Standards of Performance for Portland Cement Plants AGENCY... Emission Standards for Hazardous Air Pollutants from the Portland Cement Manufacturing Industry Response to... by the Portland Cement Industry and the New Source Performance Standards for Portland Cement Plants...

76 FR 2832 - National Emission Standards for Hazardous Air Pollutants From the Portland Cement Manufacturing...

Science.gov (United States)

2011-01-18

... Cement Manufacturing Industry and Standards of Performance for Portland Cement Plants AGENCY...) from the Portland Cement Manufacturing Industry and Standards of Performance (NSPS) for Portland Cement... Standards for Hazardous Air Pollutant From the Portland Cement Manufacturing Industry Docket, Docket ID No...

77 FR 46371 - National Emission Standards for Hazardous Air Pollutants for the Portland Cement Manufacturing...

Science.gov (United States)

2012-08-03

...-AQ93 National Emission Standards for Hazardous Air Pollutants for the Portland Cement Manufacturing... Portland Cement Manufacturing Industry and Standards of Performance for Portland Cement Plants,'' which was... Manufacturing Industry and Standards of Performance for Portland Cement Plants'' under Docket ID No. EPA-HQ-OAR...

75 FR 24703 - Findings of Misconduct in Science

Science.gov (United States)

2010-05-05

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Office of the Secretary Findings of Misconduct in Science... of HHS, issued a final notice of debarment based on the misconduct in science findings of the Office... Retrovirology Pathogenesis Laboratory, UW, committed misconduct in science (scientific misconduct) in research...

75 FR 4566 - Findings of Misconduct in Science

Science.gov (United States)

2010-01-28

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Office of the Secretary Findings of Misconduct in Science... of HHS, issued a final notice of debarment based on the misconduct in science findings of the Office..., School of Nursing, TSU, committed misconduct in science and research misconduct in research supported by...

Electrically conductive Portland cement concrete.

Science.gov (United States)

1986-01-01

There is a need for an effective, simple-to-install secondary anode system for use in the cathodic protection of reinforced concrete bridge decks. In pursuit of such a system, carbon fibers and carbon black were incorporated in portland cement concre...

Properties of Portland-Composite Cements with metakaolin: Commercial and manufactured by Thermal Activation of Serbian Kaolin Clay

Directory of Open Access Journals (Sweden)

Mitrovic A.

2012-09-01

Full Text Available Portland-composite cements (CEM II were prepared with addition of 5 to 35% of metakaolin (MK, manufactured by thermal activation/calcination of Serbian kaolin clay, and commercial matakaolin (CMK. Performance of the composite cements was evaluated, through the setting time (initial and final, compressive strengths (for ages 2, 7, 28, 90 and 180 days and soundness, and compared with control cement (Portland cement – CEM I. Setting time (initial and final is accelerated in Portlandcomposite cements, for both metakaolins used. The acceleration is higher in cement with addition of commercial metakaolin. Lower compressive strength is obtained after 2 days of curing for all Portland-composite cements in comparison with control cement, since pozzolanic reaction still did not show its effect. After 7 days, pozzolanic reaction show its effect, manifested as compressive strength increase of Portland-composite cements with addition of up to 35% of CMK, and 25% in the case of cements with MK. After 28 days compressive strength was higher than that for control cement for cements prepared with addition of CMK, and with addition of up to 25% MK. After 90 days increased compressive strength was noticed with addition of 10 - 20% of CMK, and with 10 and 15% of MK, while after 180 days addition of both metakaolins influences compressive strength decrease. The results of the soundness, 0.5 mm for CEM I, and 1.0 mm in most Portland-composite cements indicate soundness increase with addition of metakaolins. Generally, better performance of Portland-composite cements was obtained with addition of commercial metakaolin, which may be attributed to the differences in the pozzolanic activity of the applied metakaolins, 20.5 MPa and 14.9 MPa for CMK and MK, respectively. By our previous findings pozzolanic activity of the thermally activated clay may be increased by subsequent milling of the metakaolin manufactured by thermal activation process.

Thermophysical properties of blends from Portland and sulfoaluminate-belite cements

International Nuclear Information System (INIS)

Mojumdar, S.C.; Janotka, I.

2002-01-01

The behavior of mortars with blends consisting of sulfoaluminate-belite cements and ordinary Portland cement made with cement to sand ratio of 1:3 by weight and w/c = 0.5 maintained for 90 days at 20 0 C either at 60% relative humidity - dry air or 100% relative humidity - wet air. The results show insufficient character of hydraulic activity of sulfoaluminate-belite cements. Their quality has been improved. The replacement of 15 wt % of sulfoaluminate-belite cement by ordinary Portland cement influences strength positively and elasticity modulus values as well as hydrated phases and pore structure development of sulfoaluminate-belite/ordinary Portland cement blends relative to pure sulfoaluminate-belite cement systems. The above statements confirm the possible making technologies, when improvements in sulfoaluminate-belite cements quality will be achieved. One would then anticipate the competition in usages between sulfoaluminate-belite/ordinary Portland cement and blast furnace-slag Portland cement systems in the practice. It is important to consider because sulfoaluminate-belite cements are of great advantage from the viewpoint of energy savings and quantity of CO 2 released during their production. Thermal characteristics of the samples were studied by thermogravimetry and differential thermal analysis from room temperature to 1000 0 C in air atmosphere. Generally, four significant temperature regions on thermogravimetry curves with the respective differential thermal analysis peak temperature for all types of samples are observed (Authors)

Portland cement versus MTA as a root-end filling material. A pilot study.

Science.gov (United States)

da Silva, Sérgio Ribeiro; da Silva Neto, José Dias; Veiga, Daniela Francescato; Schnaider, Taylor Brandão; Ferreira, Lydia Masako

2015-02-01

To assess periradicular lesions clinically and by computed tomography (CT) after endodontic surgery using either Portland cement or mineral trioxide aggregate (MTA) as a root-end filling material. Three patients diagnosed with periradicular lesions by cone-beam CT underwent endodontic surgery with root-end filling. Patient A was treated with MTA as the root-end filling material, patient B was treated with Portland cement and patient C had two teeth treated, one with MTA and the other with Portland cement. Six months after surgery, the patients were assessed clinically and by CT scan and the obtained results were compared. Periradicular tissue regeneration was observed in all cases, with no significant differences in bone formation when comparing the use of MTA and Portland cement as root-end filling materials. Both mineral trioxide aggregate and Portland cement were successful in the treatment of periradicular lesions.

40 CFR 81.78 - Metropolitan Portland Intrastate Air Quality Control Region.

Science.gov (United States)

2010-07-01

... Quality Control Region. 81.78 Section 81.78 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.78 Metropolitan Portland Intrastate Air Quality Control Region. The Metropolitan Portland Intrastate Air Quality Control Region (Maine) consists of the territorial area...

EnviroAtlas - Portland, OR - Meter-Scale Urban Land Cover (MULC) Data (2012)

Data.gov (United States)

U.S. Environmental Protection Agency — The EnviroAtlas Portland, OR Meter-Scale Urban Land Cover (MULC) dataset includes data for the Portland metropolitan area plus the city of Vancouver, Washington and...

Biocompatibility of Portland cement combined with different radiopacifying agents.

Science.gov (United States)

Lourenço Neto, Natalino; Marques, Nádia C T; Fernandes, Ana Paula; Rodini, Camila O; Duarte, Marco A H; Lima, Marta C; Machado, Maria A A M; Abdo, Ruy C C; Oliveira, Thais M

2014-03-01

The aim of this study was to evaluate the response of rat subcutaneous tissue to Portland cement combined with two different radiopacifying agents, iodoform (CHI3) and zirconium oxide (ZrO2). These materials were placed in polyethylene tubes and implanted into the dorsal connective tissue of Wistar rats for 7 and 15 days. The specimens were then stained with hematoxylin and eosin, and inflammatory reaction parameters were evaluated by light microscopy. The intensity of the inflammatory response to the sealants was analyzed by two blind calibrated observers throughout the experimental period. Histological analysis showed that all the materials caused a moderated inflammatory reaction at 7 days, which then diminished with time. At 15 days, the inflammatory reaction was almost absent, and fibroblasts and collagen fibers were observed indicating normal tissue healing. The degrees of the inflammatory reaction on different days throughout the experimental period were compared using the non-parametric Kruskal-Wallis test. Statistical analysis demonstrated no significant differences amongst the groups, and Portland cement associated with radiopacifying agents gave satisfactory results. Therefore, Portland cement used in combination with radiopacifying agents can be considered a biocompatible material. Although our results are very encouraging, further studies are needed in order to establish safe clinical indications for Portland cement combined with radiopacifying agents.

Influence of ultrasonic radiation on the amorphous zeolite - Portland cement system

NARCIS (Netherlands)

Jakevicius, L.; Vaiciukyniene, D.; Demcenko, A.

2012-01-01

This paper considers the investigation of influence of an amorphous synthetic zeolite with inserted $Ca^{2+}$ ions additive (ASZ) on the hydration temperature of Portland cement paste. In this investigation the sonicated Portland cement paste is compared to the non-sonicated paste; and then the

Portland-pfa cement: a comparison between intergrinding and blending

Energy Technology Data Exchange (ETDEWEB)

Monk, M

1983-09-01

Portland-pfa cements containing 20-40% (by weight) pfa have been prepared in the laboratory both by intergrinding the ashes with clinker and by blending with cement. Cement properties have been assessed according to BS 4550 and scanning electron microscopy was used to examine the effects of grinding upon the pfa particles. The work has shown that intergrinding leads to an improvement in the water-reducing properties of coarse pfas and also in their pozzolanic activity as indicated by compressive strength development at later ages. Setting times have been found to be essentially the same for blended and interground cements, both being considerably longer than for typical ordinary Portland cements. Thus the results of this investigation indicate that, provided pfa's are chemically acceptable, they can be used for Portland-pfa cement manufacture by intergrinding irrespective of their coarseness.

77 FR 42367 - National Emission Standards for Hazardous Air Pollutants for the Portland Cement Manufacturing...

Science.gov (United States)

2012-07-18

... and 63 National Emission Standards for Hazardous Air Pollutants for the Portland Cement Manufacturing... Standards for Hazardous Air Pollutants for the Portland Cement Manufacturing Industry and Standards of... manufacturing plants. Federal government Not affected. State/local/tribal government.... Portland cement...

Recycled materials in Portland cement concrete

Science.gov (United States)

2000-06-01

This report pertains to a comprehensive study involving the use of recycled materials in Portland cement concrete. Three different materials were studied including crushed glass (CG), street sweepings (SS), and recycled concrete (RC). Blast furnace s...

2015 City of Portland, Maine, Lidar

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — 2015 City of Portland Maine Lidar Data Acquisition and Processing Woolpert Order No. 75564 Contractor: Woolpert, Inc. This task is for a high resolution data set of...

Analysis of Chemical Composition of Portland Cement in Ghana: A Key to Understand the Behavior of Cement

OpenAIRE

Bediako, Mark; Amankwah, Eric Opoku

2015-01-01

The performance of Portland cement in concrete or mortar formation is very well influenced by chemical compositions among other factors. Many engineers usually have little information on the chemical compositions of cement in making decisions for the choice of commercially available Portland cement in Ghana. This work analyzed five different brands of Portland cement in Ghana, namely, Ghacem ordinary Portland cement (OPC) and Portland limestone cement (PLC), CSIR-BRRI Pozzomix, Dangote OPC, a...

75 FR 54969 - National Emission Standards for Hazardous Air Pollutants From the Portland Cement Manufacturing...

Science.gov (United States)

2010-09-09

... Hazardous Air Pollutants From the Portland Cement Manufacturing Industry and Standards of Performance for... Standards for Hazardous Air Pollutants From the Portland Cement Manufacturing Industry and Standards of... (NESHAP) from the Portland Cement Manufacturing Industry and to the New Source Performance Standards (NSPS...

76 FR 2860 - National Emission Standards for Hazardous Air Pollutants From the Portland Cement Manufacturing...

Science.gov (United States)

2011-01-18

... Cement Manufacturing Industry and Standards of Performance for Portland Cement Plants AGENCY... Portland Cement Manufacturing Industry Docket, Docket ID No. EPA-HQ-OAR-2002-0051, 1200 Pennsylvania Ave... Portland Cement Manufacturing Industry Docket, EPA West, Room 3334, 1301 Constitution Ave., NW., Washington...

Influence of limestone on the hydration of Portland cements

International Nuclear Information System (INIS)

Lothenbach, Barbara; Le Saout, Gwenn; Gallucci, Emmanuel; Scrivener, Karen

2008-01-01

The influence of the presence of limestone on the hydration of Portland cement was investigated. Blending of Portland cement with limestone was found to influence the hydrate assemblage of the hydrated cement. Thermodynamic calculations as well as experimental observations indicated that in the presence of limestone, monocarbonate instead of monosulfate was stable. Thermodynamic modelling showed that the stabilisation of monocarbonate in the presence of limestone indirectly stabilised ettringite leading to a corresponding increase of the total volume of the hydrate phase and a decrease of porosity. The measured difference in porosity between the 'limestone-free' cement, which contained less than 0.3% CO 2 , and a cement containing 4% limestone, however, was much smaller than calculated. Coupling of thermodynamic modelling with a set of kinetic equations which described the dissolution of the clinker, predicted quantitatively the amount of hydrates. The quantities of ettringite, portlandite and amorphous phase as determined by TGA and XRD agreed well with the calculated amounts of these phases after different periods of time. The findings in this paper show that changes in the bulk composition of hydrating cements can be followed by coupled thermodynamic models. Comparison between experimental and modelled data helps to understand in more detail the dominating processes during cement hydration

Stabilization of marly soils with portland cement

Science.gov (United States)

Piskunov, Maksim; Karzin, Evgeny; Lukina, Valentina; Lukinov, Vitaly; Kholkin, Anatolii

2017-10-01

Stabilization of marlous soils with Portland cement will increase the service life of motor roads in areas where marl is used as a local road construction material. The result of the conducted research is the conclusion about the principal possibility of stabilization of marlous soils with Portland cement, and about the optimal percentage of the mineral part and the binding agent. When planning the experiment, a simplex-lattice plan was implemented, which makes it possible to obtain a mathematical model for changing the properties of a material in the form of polynomials of incomplete third order. Brands were determined for compressive strength according to GOST 23558-94 and variants of stabilized soils were proposed for road construction.

76 FR 78240 - Gray Portland Cement and Clinker From Japan: Continuation of Antidumping Duty Order

Science.gov (United States)

2011-12-16

... DEPARTMENT OF COMMERCE International Trade Administration [A-588-815] Gray Portland Cement and... Department) initiated the third sunset review of the antidumping duty order on gray portland cement and... of the antidumping duty order on gray portland cement and clinker from Japan would likely lead to...

Portland cement concrete air content study.

Science.gov (United States)

1987-04-20

This study took the analysis of Portland cement concrete air content. Based on the information gathered, this study hold the results were : 1) air-entrained concrete was more durable than non-air entrained concrete all other factors being equal; 2) A...

Biological evaluation of a new pulp capping material developed from Portland cement.

Science.gov (United States)

Negm, Ahmed M; Hassanien, Ehab E; Abu-Seida, Ashraf M; Nagy, Mohamed M

2017-03-02

This study evaluates the biological properties of a new pulp capping material developed from Portland cement. This study was conducted on 48 teeth in 4 dogs (12 teeth/dog). The dogs were classified into two equal groups (n=24 teeth) according to the evaluation period including: group A (3 weeks) and group B (3 months). Each group was further subdivided into three equal subgroups (n=8 teeth) according to the capping material including: subgroup 1: mineral trioxide aggregate (MTA), subgroup2: Portland cement+10% calcium hydroxide+20% bismuth oxide (Port Cal) and subgroup 3: Portland cement+bismuth oxide. After general anesthesia, a class V buccal cavity was prepared coronal to the gingival margin. After pulp exposure and hemostasis,the capping materials and glass ionomer filling were placed on the exposure sites. All histopathological findings, inflammatory cell count and dentin bridge formation were recorded. Data were analyzed statistically. After 3 months, the histopathological picture of the pulp in subgroup 1 showed normal pulp, continuous odontoblastic layer and complete dentin bridge formation while subgroup 2 showed partial and complete dentin bridge over a normal and necrotic pulps. Subgroup 3 showed loss of normal architecture, areas of necrosis, complete, or incomplete dentin bridge formation, attached and detached pulp stones and fatty degeneration in group B. For group A, MTA subgroup showed the least number of inflammatory cell infiltrate followed by Port Cal subgroup. While subgroup 3 showed the highest number of inflammatory cell infiltrate. For group B, the mean inflammatory cell count increased with the three tested materials with no statistical difference. Regarding dentin bridge formation at group A, no significant differences was found between subgroups, while at group B, MTA subgroup exhibited significantly higher scores than other subgroups. In conclusion, addition of calcium hydroxide to Portland cement improves the dentin bridge formation

Effect of mineral trioxide aggregates and Portland cements on inflammatory cells.

Science.gov (United States)

Shahi, Shahriar; Rahimi, Saeed; Yavari, Hamid Reza; Mokhtari, Hadi; Roshangar, Leila; Abasi, Mehran Mesgary; Sattari, Sahar; Abdolrahimi, Majid

2010-05-01

Recently, some studies have compared mineral trioxide aggregate (MTA) with Portland cements, concluding that the principal ingredients of Portland cements are similar to those of MTA. The purpose of the present study was to evaluate the effect of gray MTA, white MTA, and gray and white Portland cements on inflammatory cells in rats. Fresh mixtures mixed with distilled water were placed in polyethylene tubes, which were implanted in the dorsal subcutaneous connective tissue of 60 Sprague-Dawley rats along with empty tubes as controls. Tissue specimens were collected after the rats were sacrificed after 7, 15, 30, 60, and 90 days. The specimens were fixed, stained, processed, and histologically evaluated under a light microscope. Inflammatory reactions were classified as grade 0: without inflammatory cells, grade I: sporadic infiltration of inflammatory cells, grade II: moderate infiltration (125 cells). Data were analyzed with the nonparametric (two factor) analysis of variance and Kruskal-Wallis H-test. All the groups showed grade III inflammation after 7 and 15 days; there was a decrease in the inflammatory process after 30, 60, and 90 days. After 90 days, gray MTA, white MTA, and control groups had grade 0 inflammatory process, but gray Portland cement and white Portland cement groups showed grade 0 to grade I inflammatory processes. MTAs were more biocompatible; however, more studies are required. Copyright (c) 2010 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Synthesis of Portland cement and calcium sulfoaluminate-belite cement for sustainable development and performance

Science.gov (United States)

Chen, Irvin Allen

Portland cement concrete, the most widely used manufactured material in the world, is made primarily from water, mineral aggregates, and portland cement. The production of portland cement is energy intensive, accounting for 2% of primary energy consumption and 5% of industrial energy consumption globally. Moreover, portland cement manufacturing contributes significantly to greenhouse gases and accounts for 5% of the global CO2 emissions resulting from human activity. The primary objective of this research was to explore methods of reducing the environmental impact of cement production while maintaining or improving current performance standards. Two approaches were taken, (1) incorporation of waste materials in portland cement synthesis, and (2) optimization of an alternative environmental friendly binder, calcium sulfoaluminate-belite cement. These approaches can lead to less energy consumption, less emission of CO2, and more reuse of industrial waste materials for cement manufacturing. In the portland cement part of the research, portland cement clinkers conforming to the compositional specifications in ASTM C 150 for Type I cement were successfully synthesized from reagent-grade chemicals with 0% to 40% fly ash and 0% to 60% slag incorporation (with 10% intervals), 72.5% limestone with 27.5% fly ash, and 65% limestone with 35% slag. The synthesized portland cements had similar early-age hydration behavior to commercial portland cement. However, waste materials significantly affected cement phase formation. The C3S--C2S ratio decreased with increasing amounts of waste materials incorporated. These differences could have implications on proportioning of raw materials for cement production when using waste materials. In the calcium sulfoaluminate-belite cement part of the research, three calcium sulfoaluminate-belite cement clinkers with a range of phase compositions were successfully synthesized from reagent-grade chemicals. The synthesized calcium sulfoaluminate

75 FR 73084 - Findings of Misconduct in Science

Science.gov (United States)

2010-11-29

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Office of the Secretary Findings of Misconduct in Science..., former graduate student, Department of Chemistry, CU, engaged in misconduct in science in research funded by National Institute of General Medical Sciences (NIGMS), National Institutes of Health (NIH), grant...

33 CFR 165.1312 - Security Zone; Portland Rose Festival on Willamette River.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Security Zone; Portland Rose Festival on Willamette River. 165.1312 Section 165.1312 Navigation and Navigable Waters COAST GUARD... § 165.1312 Security Zone; Portland Rose Festival on Willamette River. (a) Location. The following area...

78 FR 4331 - Safety Zone; Sellwood Bridge Move; Willamette River, Portland, OR

Science.gov (United States)

2013-01-22

... Sellwood Bridge as it is being moved. This safety zone will also allow full maneuverability for... 1625-AA00 Safety Zone; Sellwood Bridge Move; Willamette River, Portland, OR AGENCY: Coast Guard, DHS... the Sellwood Bridge, located on the Willamette River in Portland, Oregon, while it is being relocated...

The existence state of uranium(VI) in portland cement matrix material immobilization body

International Nuclear Information System (INIS)

Tan Hongbin; Li Yuxiang

2005-01-01

The basis of Portland cement material reaction with uranium, the corrosion of uranium minerals in nature and the state of study on immobilization of uranium by Portland cement matrix material are introduced, and some considerations are presented. (authors)

Gravity Data for the Greater Portland Area

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The gravity station data (1,522 records) were compiled by the Portland State University. This data base was received in August 1990. Principal gravity parameters...

Formula of Moulding Sand, Bentonite and Portland Cement toImprove The Quality of Al-Si Cast Alloy

OpenAIRE

Andoko Andoko; Poppy Puspitasari; Avita Ayu Permanasari; Didin Zakaria Lubis

2017-01-01

A binder is any material used to strengthen the bonding of moulding sand grains. The primary function of the binder is to hold the moulding sand and other materialstogether to produce high-quality casts. In this study, there were four binder compositions being tested, i.e. 5% bentonite + 5% Portland cement, 4% bentonite + 6% Portland cement, 6% bentonite + 4% Portland cement, and 7% bentonite + 3% Portland cement. Each specimen was measured for its compressive strength, shear strength, tensil...

Lift : Special Needs Transportation in Portland, Oregon

Science.gov (United States)

1978-01-01

The report covers Portland, Oregon's Special Needs Transportation (SNT) project - the Lift - during its first year of operation. The purposes of this UMTA Service and Methods Demonstration (SMD) is to: (1) test a transit operator's ability to provide...

Modelling porewater chemistry in hydrated Portland cement

International Nuclear Information System (INIS)

Berner, U.R.

1987-01-01

Extensive employment of concrete is foreseen in radioactive waste repositories. A prerequisite for modelling the interactions between concrete and formation waters is characterization of the concrete system. Available experimental data from high pressure squeezing of cement pore-water indicate that, besides the high pH due to alkali hydroxide dissolution, cement composition itself influences the solubility determining solid phases. A model which simulates the hydration of Portland cement assuming complete hydration of the main clinker minerals is presented. The model also includes parameters describing the reactions between the cement and blending agents. Comparison with measured pore-water data generally gives a consistent picture and, as expected, the model gives correct predictions for pure Portland cements. For blended cements, the required additional parameters can, to some extent, be derived from pore-water analysis. 14 references, 1 figure, 4 tables

33 CFR 100.1302 - Special Local Regulation, Annual Dragon Boat Races, Portland, Oregon.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Special Local Regulation, Annual Dragon Boat Races, Portland, Oregon. 100.1302 Section 100.1302 Navigation and Navigable Waters COAST... § 100.1302 Special Local Regulation, Annual Dragon Boat Races, Portland, Oregon. (a) Regulated area. All...

Effect of wastewater on properties of Portland pozzolana cement

Science.gov (United States)

Babu, G. Reddy

2017-07-01

This paper presents the effect of wastewaters on properties of Portland pozzolana cement (PPC). Fourteen water treatment plants were found out in the Narasaraopet municipality region in Guntur district, Andhra Pradesh, India. Approximately, from each plant, between 3500 and 4000 L/day of potable water is selling to consumers. All plants are extracting ground water and treating through Reverse Osmosis (RO) process. During water treatment, plants are discharging approximately 1,00,000 L/day as wastewater in side drains in Narasaraopet municipality. Physical and chemical analysis was carried out on fourteen plants wastewater and distilled water as per producer described in APHA. In the present work, based on the concentrations of constituent's in wastewater, four typical plants i.e., Narasaraopeta Engineering College (NECWW), Patan Khasim Charitable Trust (PKTWW), Mahmadh Khasim Charitable Trust (MKTWW) and Amara (ARWW) were considered. The performance of four plants wastewater on physical properties i.e., setting times, compressive strength, and flexural strength of Portland pozzolana Cement (PPC) were performed in laboratories and compared same with reference specimens i.e., made with Distilled Water (DW) as mixing water. No significant change was observed in initial and finial setting time but setting times of selected wastewaters were retarded as compared to that of reference water. Almost, no change was observed in 90 days compressive and flexural strengths in four plants wastewaters specimens compared to that of reference water specimens. XRD technique was employed to find out main hydration compounds formed in the process.

Hospital waste ashes in Portland cement mortars

International Nuclear Information System (INIS)

Genazzini, C.; Zerbino, R.; Ronco, A.; Batic, O.; Giaccio, G.

2003-01-01

Nowadays, most concretes incorporate mineral additions such as pozzolans, fly ash, silica fume, blast furnace slag, and calcareous filler among others. Although the technological and economical benefits were the main reasons for the use of mineral additions, the prevention of environmental contamination by means of proper waste disposal becomes a priority. The chance of incorporating hospital waste ashes in Portland cement-based materials is presented here. Ash characterization was performed by chemical analysis, X-ray diffraction, radioactive material detection, and fineness and density tests. Conduction calorimetry and setting time tests were developed on pastes including ash contents from 0% to 100%. Mortars were prepared including ash contents up to 50% of cement. The results of setting time, temperature development, flexural and compressive strengths, water absorption, density, and leachability are analyzed. Results indicate that Portland cement systems could become an alternative for the disposal of this type of ashes

Radiopacity evaluation of Portland and MTA-based cements by digital radiographic system.

Science.gov (United States)

Borges, Alvaro Henrique; Pedro, Fabio Luiz Miranda; Semanoff-Segundo, Alex; Miranda, Carlos Eduardo Saraiva; Pécora, Jesus Djalma; Cruz Filho, Antônio Miranda

2011-01-01

The aim of the present study was to evaluate the radiopacity of Portland and MTA-based cements using the Digora TM digital radiographic system. The performed tests followed specification number 57 from the American National Standard Institute/American Dental Association (2000) for endodontic sealing materials. The materials were placed in 5 acrylic plates, especially designed for this experiment, along with a graduated aluminum stepwedge varying from 1 to 10 mm in thickness. The set was radiographed at a 30 cm focus-object distance and with 0.2 s exposure time. After the radiographs were taken, the optical laser readings of radiographs were performed by Digora TM system. Five radiographic density readings were performed for each studied material and for each step of the aluminum scale. White ProRoot MTA (155.99±8.04), gray ProRoot MTA (155.96±16.30) and MTA BIO (143.13±16.94) presented higher radiopacity values (pPortland (119.76±22.34), gray Portland (109.71±4.90) and white structural Portland (99.59±12.88) presented lower radiopacity values (pcements were the only materials presenting radiopacity within the ANSI/ADA specifications.

Partial replacement of Portland cement by red ceramic waste in mortars: study of pozzolanic activity; Substituicao parcial do cimento Portland por residuo de ceramica vermelha em argamassas: estudo da atividade pozolonica

Energy Technology Data Exchange (ETDEWEB)

Silva, A.R. da; Cabral, K.C.; Pinto, E.N. de M.G.l., E-mail: kleber.cabral@ufersa.edu.br [Universidade Federal Rural do Semi-Arido (UFERSA), Mossoro, RN (Brazil)

2016-07-01

The objective of this study is to analyze the pozzolanic activity of red ceramic residue on the partial replacement of Portland cement in mortars. The mortars were prepared by substituting 25% of the Portland cement for ground of ceramic residue with water cement’s factor of 0.48. The concrete used to construct the reference mortars and those with addiction was CPII-Z-32 (compound of Portland pozzolana cement). The chemical analysis and physical ceramic waste showed that this meets the requirements of NBR12653 (2014) for use as pozzolanic material. The pozzolanic activity index (IAP) obtained for the ceramic waste to twenty-eight days cure rate was 80.28%. (author)

Social Science Research Findings and Educational Policy Dilemmas

Directory of Open Access Journals (Sweden)

Steven I. Miller

2000-01-01

Full Text Available The article attempts to raise several distinctions regarding the presumed relationship of social science research findings to social policy making. The distinctions are made using Glymour's critique of the Bell Curve. An argument is made that (1 social science models and research findings are largely irrelevant to the actual concerns of policy makers and (2 what is relevant, but overlooked by Glymour, is how ideological factors mediate the process. The forms that ideological mediation may take are indicated.

A comparative evaluation of compressive strength of Portland cement with zinc oxide eugenol and Polymer-reinforced cement: an in vitro analysis.

Science.gov (United States)

Prakasam, S; Bharadwaj, Prakasam; Loganathan, S C; Prasanth, B Krishna

2014-01-01

The purpose of this study is to evaluate the ultimate compressive strength of 50% and 25% Portland cement mixed with Polymer-reinforced zinc oxide eugenol and zinc oxide eugenol cement after 1 hour, 24 hours, and 7 days. One hundred and eighty samples were selected. The samples were made cylindrical of size 6 × 8 mm and were divided into six groups as follows with each group consisting of 10 samples. Group 1: Polymer-reinforced zinc oxide eugenol with 50% Portland cement (PMZNPC 50%) Group 2: Polymer-reinforced zinc oxide eugenol with 25% Portland cement (PMZNPC 25%) Group 3: Polymer-reinforced zinc oxide eugenol with 0% Portland cement (PMZNPC 0%) Group 4: Zinc oxide eugenol with 50% Portland cement (ZNPC 50%) Group 5: Zinc oxide eugenol with 25% Portland cement (ZNPC 25%) Group 6: Zinc oxide eugenol with 0% Portland cement (ZNPC 0%) These samples were further subdivided based on time interval and were tested at 1 hour, 24 hours and at 7 th day. After each period of time all the specimens were tested by vertical CVR loaded frame with capacity of 5 tones/0473-10kan National Physical laboratory, New Delhi and the results were statistically analyzed using ANOVA and Scheffe test. Polymer-reinforced cement with 50% Portland cement, Zinc oxide with 50% Portland cement, Polymer-reinforced cement with 25% Portland cement and Zinc oxide with 25% Portland cement exhibited higher compressive strength when compared to Zinc oxide with 0% Portland cement and Polymer-reinforced cement with 0% Portland cement, at different periods of time. The difference between these two groups were statistically significant (P Portland cement in Zinc oxide eugenol and Polymer-modified zinc oxide cement can be used as core build up material and permanent filling material. It is concluded that 50% and 25% Portland cement in zinc oxide eugenol and polymer-modified zinc oxide eugenol results in higher compressive strength and hence can be used as permanent filling material and core built

Interfacial morphology and domain configurations in 0-3 PZT-Portland cement composites

International Nuclear Information System (INIS)

Jaitanong, N.; Zeng, H.R.; Li, G.R.; Yin, Q.R.; Vittayakorn, W.C.; Yimnirun, R.; Chaipanich, A.

2010-01-01

Cement-based piezoelectric composites have attracted great attention recently due to their promising applications as sensors in smart structures. Lead zirconate titanate (PZT) and Portland cement (PC) composite were fabricated using 60% of PZT by volume. Scanning Electron Microscope and piezoresponse force microscope were used to investigate the morphology and domain configurations at the interfacial zone of PZT-Portland cement composites. Angular PZT ceramic grains were found to bind well with the cement matrix. The submicro-scale domains were clearly observed by piezoresponse force microscope at the interfacial regions between the piezoelectric PZT phase and Portland cement phase, and are clearer than the images obtained for pure PZT. This is thought to be due to the applied internal stress of cement to the PZT ceramic particle which resulted to clearer images.

78 FR 4381 - Foreign-Trade Zone 45-Portland, Oregon; Application for Reorganization and Expansion Under...

Science.gov (United States)

2013-01-22

... following sites: Site 1 (1,830 acres)--Rivergate Industrial Park, Port Terminal Nos. 5 and 6, and the... Way and NE Alderwood Road, Portland; Site 3 (254 acres)--Portland Ship Repair Yard, 5555 N. Channel...

Chemical composition, radiopacity, and biocompatibility of Portland cement with bismuth oxide.

Science.gov (United States)

Hwang, Yun-Chan; Lee, Song-Hee; Hwang, In-Nam; Kang, In-Chol; Kim, Min-Seok; Kim, Sun-Hun; Son, Ho-Hyun; Oh, Won-Mann

2009-03-01

This study compared the chemical constitution, radiopacity, and biocompatibility of Portland cement containing bismuth oxide (experimental cement) with those of Portland cement and mineral trioxide aggregate (MTA). The chemical constitution of materials was determined by scanning electron microscopy and energy-dispersive X-ray analysis. The radiopacity of the materials was determined using the ISO/6876 method. The biocompatibility of the materials was tested by MTT assay and tissue reaction. The constitution of all materials was similar. However, the Portland cement and experimental cement were more irregular and had a larger particle size than MTA. The radiopacity of the experimental cement was similar to MTA. The MTT assay revealed MTA to have slightly higher cell viability than the other materials. However, there were no statistically significant differences between the materials, with the exception of MTA at 24 h. There was no significant difference in the tissue reaction between the experimental groups. These results suggest that the experimental cement may be used as a substitute for MTA.

Potencialidades da metacaolinita e do tijolo queimado moído como substitutos parciais do cimento Portland Potentialities of metakaolin and crushed waste calcined clay brick as partial replacement of Portland cement

Directory of Open Access Journals (Sweden)

João de Farias Filho

2000-12-01

Full Text Available Avalia-se, neste trabalho, a potencialidade do uso da metacaolinita e dos resíduos de produção de tijolos cerâmicos queimados finamente moídos, como substitutos parciais do cimento Portland. Os materiais foram caracterizados física, química e mineralogicamente, além de determinado o índice de atividade pozolânica com cimento Portland. A evolução da resistência a compressão e a flexão das argamassas foi avaliada até as idades de, respectivamente, 365 e 208 dias. As porcentagens de substituição do cimento Portland, em peso, pelos materiais pozolânicos, variaram de 20 a 50%, enquanto o fator água/cimento variou de 0,37 a 0,45. Os resultados obtidos indicaram que a metacaolinita e o tijolo moído queimado possuem elevada atividade pozolânica e que a resistência a compressão, aos 28 dias, das argamassas mistas, foi superior à das argamassas de cimento Portland para os níveis de substituição e fatores água/cimento estudados. Um modelo matemático para predição da resistência à compressão das argamassas mistas é proposto com base em um desenho fatorial de experimentos.This paper evaluates the potentiality of metakaolin and crushed waste fired clay brick as cement replacement materials. They were characterised physically, chemically and mineralogically and their activity with Portland cement determined. The influence of the partial replacement of Portland cement on the development of compressive and flexural strength was evaluated until the age of, respectively, 365 and 208 days. The percentage of cement replacement, in weight, ranged from 20 to 50%, whereas the water/cement ratio ranged from 0.37 to 0.45. The results obtained show that the metakaolin and crushed calcined clay brick presented a good pozolanic activity and that the compressive strength of the blended mortars after 28 days of cure was higher than that observed for the reference Portland cement for all levels of cement replacement and water/cement ratio. A

Optimization of calcium chloride content on bioactivity and mechanical properties of white Portland cement

International Nuclear Information System (INIS)

Torkittikul, Pincha; Chaipanich, Arnon

2012-01-01

This research investigates the optimization of calcium chloride content on the bioactivity and mechanical properties of white Portland cement. Calcium chloride was used as an addition of White Portland cement at 0, 1, 2, 3, 4, 5, 6, 7, 8, 9 and 10% by weight. Calcium chloride was dissolved in sterile distilled water and blended with White Portland cement using a water to cement ratio of 0.5. Analysis of the bioactivity and pH of white Portland cement pastes with calcium chloride added at various amounts was carried out in simulated body fluid. Setting time, density, compressive strength and volume of permeable voids were also investigated. The characteristics of cement pastes were examined by X-ray diffractometer and scanning electron microscope linked to an energy-dispersive X-ray analyzer. The result indicated that the addition of calcium chloride could accelerate the hydration of white Portland cement, resulting in a decrease in setting time and an increase in early strength of the pastes. The compressive strength of all cement pastes with added calcium chloride was higher than that of the pure cement paste, and the addition of calcium chloride at 8 wt.% led to achieving the highest strength. Furthermore, white Portland cement pastes both with and without calcium chloride showed well-established bioactivity with respect to the formation of a hydroxyapatite layer on the material within 7 days following immersion in simulated body fluid; white Portland cement paste with added 3%CaCl 2 exhibited the best bioactivity. - Highlights: ► Optimization CaCl 2 content on the bioactivity and mechanical properties. ► CaCl 2 was used as an addition at 0, 1, 2, 3, 4, 5, 6, 7, 8, 9 and 10% by weight. ► CaCl 2 resulted in a decrease in setting time and an increase in early strength. ► Addition of 3%CaCl 2 exhibited the optimum formation of hydroxyapatite.

Binding of chloride and alkalis in Portland cement systems

International Nuclear Information System (INIS)

Nielsen, Erik P.; Herfort, Duncan; Geiker, Mette R.

2005-01-01

A thermodynamic model for describing the binding of chloride and alkalis in hydrated Portland cement pastes has been developed. The model is based on the phase rule, which for cement pastes in aggressive marine environment predicts multivariant conditions, even at constant temperature and pressure. The effect of the chloride and alkalis has been quantified by experiments on cement pastes prepared from white Portland cements containing 4% and 12% C 3 A, and a grey Portland cement containing 7% C 3 A. One weight percent calcite was added to all cements. The pastes prepared at w/s ratio of 0.70 were stored in solutions of different Cl (CaCl 2 ) and Na (NaOH) concentrations. When equilibrium was reached, the mineralogy of the pastes was investigated by EDS analysis on the SEM. A well-defined distribution of chloride was found between the pore solution, the C-S-H phase, and an AFm solid solution phase consisting of Friedel's salt and monocarbonate. Partition coefficients varied as a function of iron and alkali contents. The lower content of alkalis in WPC results in higher chloride contents in the C-S-H phase. High alkali contents result in higher chloride concentrations in the pore solution

Contribución al estudio de los reacciones de hidratación del cemento portland por espectroscopia infrarroja II. Estudio de clínkeres y de cementos portland anhidros

Directory of Open Access Journals (Sweden)

Vázquez-Moreno, Tomás

1976-06-01

Full Text Available Not availableEn un artículo anterior (1 se dio cuenta de los trabajos realizados sobre la aplicación de la espectroscopia IR al estudio de las principales fases sintetizadas del clínker de cemento portland como fase previa al estudio de diversos clínkeres, obtenidos por nosotros en el laboratorio a partir de crudos industriales, y de distintos cementos portland comerciales anhidros.

Stabilization of chromium salt in ordinary portland cement

Indian Academy of Sciences (India)

Ordinary Portland cement (OPC) samples containing the chromium salt have been investigated using differential microcalorimetry, conductometry and Fourier transform infrared spectroscopic analysis. The effect of chromium on OPC hydration was evaluated by continuous observing of early hydration.

Evaluation of the strength and radiopacity of Portland cement with varying additions of bismuth oxide.

Science.gov (United States)

Saliba, E; Abbassi-Ghadi, S; Vowles, R; Camilleri, J; Hooper, S; Camilleri, J

2009-04-01

To study the effect of addition of various proportions of bismuth oxide on compressive strength and radiopacity of Portland cement. The compressive strength of white Portland cement and cement replaced with 10, 15, 20, 25 and 30% bismuth oxide was evaluated by testing cylinders 6 mm in diameter and 12 mm high. Twelve cylinders were tested for each material under study. The radiopacity of the cements tested was evaluated using an aluminium step-wedge and densitometer. The optical density was compared with the relevant thickness of aluminium (Al). Statistical analysis was performed using Analysis of Variance (ANOVA) with P = 0.05 and Tukey test to perform multiple comparison tests. Various additions of bismuth oxide had no significant effect on the strength of the material when compared with the unmodified Portland cement (P > 0.05). The radiopacity of the cements tested ranged from 2.02 mm Al for Portland cement to 9.79 mm Al for the highest bismuth replacement. Addition of bismuth oxide did not affect the compressive strength of Portland cement. All the bismuth oxide cement mixtures had radio-opacities higher than 3 mm thickness of aluminium.

EnviroAtlas - Portland, ME - Ecosystem Services by Block Group

Data.gov (United States)

U.S. Environmental Protection Agency — This EnviroAtlas dataset presents environmental benefits of the urban forest in 146 block groups in Portland, Maine. Carbon attributes, temperature reduction,...

EnviroAtlas - Portland, OR - Ecosystem Services by Block Group

Data.gov (United States)

U.S. Environmental Protection Agency — This EnviroAtlas dataset presents environmental benefits of the urban forest in 1176 block groups in Portland, Oregon. Carbon attributes, temperature reduction,...

Silica fume effect on retention characteristics of portland cement for uranium (VI)

International Nuclear Information System (INIS)

Tan Hongbin; Ma Xiaoling; Li Yuxiang

2005-01-01

With simulated groundwater as leachant, the retention capabilities of the portland cement, which contains different amount of silica fume, are investigated under 25 degree C and 42 days. The results indicate that silica fume can improve the retention capabilities of portland cement for uranium. When the cement contains 15% silica fume, the diffusion coefficient is 7 x 10 -3 cm 3 · -1 . It is only 5.5% of the cement without containing fume. (authors)

Sealing ability of mineral trioxide aggregate and Portland cement for furcal perforation repair: a protein leakage study.

Science.gov (United States)

Shahi, Shahriar; Rahimi, Saeed; Hasan, Maryam; Shiezadeh, Vahab; Abdolrahimi, Majid

2009-12-01

The purpose of this study was to compare the sealing ability of gray mineral trioxide aggregate (GMTA), white MTA (WMTA), and both white and gray Portland cement as furcation perforation repair materials. A total of 120 human mandibular first molars were used. After root canal obturation and preparation of furcal perforations the specimens were randomly divided into four groups of 25 teeth each. In groups A, B, C, and D furcation perforations were filled with WMTA, GMTA, white Portland cement, and type II Portland cement, respectively. Ten teeth were used as positive controls with no filling materials in the perforations and 10 teeth with complete coverage with two layers of nail varnish were used as negative controls. A protein leakage model utilizing 22% bovine serum albumin (BSA) was used for evaluation. Leakage was noted when color conversion of the protein reagent was observed. The controls behaved as expected. Leakage was found in the samples from group A (WMTA), group B (GMTA), and in the two other groups (white and gray Portland cement). There were no statistically significant differences between GMTA and WMTA or white and gray Portland cement, but significant differences were observed between the MTA groups and the Portland cement groups. It was concluded that Portland cements have better sealing ability than MTA, and can be recommended for repair of furcation perforation if the present results are supported by other in vivo and in vitro studies.

Mineral trioxide aggregate and Portland cement promote biomineralization in vivo.

Science.gov (United States)

Dreger, Luonothar Antunes Schmitt; Felippe, Wilson Tadeu; Reyes-Carmona, Jessie Fabiola; Felippe, Gabriela Santos; Bortoluzzi, Eduardo Antunes; Felippe, Mara Cristina Santos

2012-03-01

Mineral trioxide aggregate (MTA) and Portland cement have been shown to be bioactive because of their ability to produce biologically compatible carbonated apatite. This study analyzed the interaction of MTA and white Portland cement with dentin in vivo. Seventy-two human dentin tubes were filled with MTA Branco, MTA BIO, and white Portland cement + 20% bismuth oxide (PC1) or PC1 + 10% of calcium chloride (PC2) and implanted subcutaneously in 18 rats at 4 sites from the dorsal area. Empty dentin tubes, implanted in rats of a pilot study, were used as control. After 30, 60, and 90 days, the animals were killed, and the dentin tubes were retrieved for scanning electron microscope analysis. In the periods of 30 and 60 days, the mineral deposition in the material-dentin interface (interfacial layer) and in the interior of dentinal tubules was detected in more tubes filled with MTA Branco and MTA BIO than in tubes filled with PC1 and PC2. After 90 days, the interfacial layer and intratubular mineralization were detected in all tubes except for 3 and 1 of the tubes filled with PC2, respectively. It was concluded that all the cements tested were bioactive. The cements released some of their components in the tissue capable of stimulating mineral deposition in the cement-dentin interface and in the interior of the dentinal tubules. MTA BIO and MTA Branco were more effective in promoting the biomineralization process than Portland cements, mainly after 30 and 60 days. Copyright © 2012 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Hydromania II: Journey of the Oncorhynchus. Summer Science Camp Curriculum 1994.

Energy Technology Data Exchange (ETDEWEB)

Moura, Joan; Swerin, Rod

1995-01-01

The Hydromania II curriculum was written for the third in a series of summer science camp experiences targeting students in grades 4--6 who generally have difficulty accessing supplementary academic programs. The summer science camp in Portland is a collaborative effort between Bonneville Power Administration (BPA), the US Department of Energy (DOE), and the Portland Parks and Recreation Community Schools Program along with various other cooperating businesses and organizations. The curriculum has also been incorporated into other summer programs and has been used by teachers to supplement classroom activities. Camps are designed to make available, affordable learning experiences that are fun and motivating to students for the study of science and math. Inner-city, under-represented minorities, rural, and low-income families are particularly encouraged to enroll their children in the program.

Alkali binding in hydrated Portland cement paste

NARCIS (Netherlands)

Chen, Wei; Brouwers, Jos

2010-01-01

The alkali-binding capacity of C–S–H in hydrated Portland cement pastes is addressed in this study. The amount of bound alkalis in C–S–H is computed based on the alkali partition theories firstly proposed by Taylor (1987) and later further developed by Brouwers and Van Eijk (2003). Experimental data

Hydration of Blended Portland Cements Containing Calcium-Aluminosilicate Glass Powder and Limestone

DEFF Research Database (Denmark)

Moesgaard, M; Poulsen, Søren Lundsted; Herfort, D

2012-01-01

M. MOESGAARD, S.L. POULSEN, D. HERFORT, M. STEENBERG, L.F. KIRKEGAARD, J. SKIBSTED, Y. YUE, Hydration of Blended Portland Cements Containing Calcium-Aluminosilicate Glass Powder and Limestone, Journal of the American Ceramic Society 95, 403 – 409 (2012).......M. MOESGAARD, S.L. POULSEN, D. HERFORT, M. STEENBERG, L.F. KIRKEGAARD, J. SKIBSTED, Y. YUE, Hydration of Blended Portland Cements Containing Calcium-Aluminosilicate Glass Powder and Limestone, Journal of the American Ceramic Society 95, 403 – 409 (2012)....

Sulfatos en el cemento portland y su incidencia sobre el falso fraguado: Estado actual del conocimiento

Directory of Open Access Journals (Sweden)

de la Cruz, Ignacio

1983-12-01

Full Text Available A bibliographical study is carried out of the sulphates which may be present in the clinker and Portland cement, as likewise the effects of the aeration and temperature on the setting. This work is a prior phase of a wide experimental investigation carried out in the IETCC, on anomalies or setting and phenomena of "lumping" in Portland cement.

Se realiza un estudio bibliográfico de los sulfatos que pueden estar presentes en el clínker y cemento portland, así como de los efectos de la aireación y temperatura sobre el fraguado. Este trabajo es la fase previa de una amplia investigación experimental realizada en el IETCC, sobre anomalías de fraguado y fenómenos de "aterronamiento" en el cemento portland.

Physicochemical Properties of MTA and Portland Cement after Addition of Aloe Vera.

Science.gov (United States)

Henrique Borges, Alvaro; Aguirre Guedes, Orlando; Evaristo Ricci Volpato, Luiz; Siebert Filho, Gilberto; Meireles Borba, Alexandre; Zina, Omar; Piva, Evandro; Estrela, Carlos

2017-01-01

The aim of this in vitro study was to determine the liquid-powder ratio, setting time, solubility, dimensional change, pH, and radiopacity of white structural and non-structural Portland cement, ProRoot MTA and MTA Bio, associated with a 2% glycolic solution containing Aloe Vera, as vehicle. Five samples of each material were used for each test, according to the American National Standards Institute/American Dental Association (ANSI/ADA) specification No. 57. Statistical analyses were performed using ANOVA and Tukey's test at 5% significance. When sample distribution was not normal, non-parametric analysis of variance and the Kruskal-Wallis test were used ( α =0.05). No statistical differences were found in liquid-powder ratios among the tested materials. ProRoot MTA showed the longest setting time. Dimensional change values were acceptable in all groups. Also, no significant differences were found in pH values and pH was alkaline in all samples throughout the experiment. Mean radiopacity results obtained for white Portland cements did not meet ANSI/ADA requirements, and were significantly lower than those obtained for MTA-based cements. Finally, Portland cements showed significantly higher mean solubility values compared to the other samples. The physicochemical properties of the tested materials in association with Aloe Vera were compatible with ANSI/ADA requirements, except for the white Portland cements, which failed to meet the radiopacity specification.

Hydration characteristics of zirconium oxide replaced Portland cement for use as a root-end filling material.

Science.gov (United States)

Camilleri, J; Cutajar, A; Mallia, B

2011-08-01

Zirconium oxide can be added to dental materials rendering them sufficiently radiopaque. It can thus be used to replace the bismuth oxide in mineral trioxide aggregate (MTA). Replacement of Portland cement with 30% zirconium oxide mixed at a water/cement ratio of 0.3 resulted in a material with adequate physical properties. This study aimed at investigating the microstructure, pH and leaching in physiological solution of Portland cement replaced zirconium oxide at either water-powder or water-cement ratios of 0.3 for use as a root-end filling material. The hydration characteristics of the materials which exhibited optimal behavior were evaluated. Portland cement replaced by zirconium oxide in varying amounts ranging from 0 to 50% in increments of 10 was prepared and divided into two sets. One set was prepared at a constant water/cement ratio while the other set at a constant water/powder ratio of 0.3. Portland cement and MTA were used as controls. The materials were analyzed under the scanning electron microscope (SEM) and the hydration products were determined. X-ray energy dispersive analysis (EDX) was used to analyze the elemental composition of the hydration products. The pH and the amount of leachate in Hank's balanced salt solution (HBSS) were evaluated. A material that had optimal properties that satisfied set criteria and could replace MTA was selected. The microstructure of the prototype material and Portland cement used as a control was assessed after 30 days using SEM and atomic ratio diagrams of Al/Ca versus Si/Ca and S/Ca versus Al/Ca were plotted. The hydration products of Portland cement replaced with 30% zirconium oxide mixed at water/cement ratio of 0.3 were calcium silicate hydrate, calcium hydroxide and minimal amounts of ettringite and monosulphate. The calcium hydroxide leached in HBSS solution resulted in an increase in the pH value. The zirconium oxide acted as inert filler and exhibited no reaction with the hydration by-products of Portland

Quantitative study of Portland cement hydration by X-Ray diffraction/Rietveld analysis and geochemical modeling

Science.gov (United States)

Coutelot, F.; Seaman, J. C.; Simner, S.

2017-12-01

In this study the hydration of Portland cements containing blast-furnace slag and type V fly ash were investigated during cement curing using X-ray diffraction, with geochemical modeling used to calculate the total volume of hydrates. The goal was to evaluate the relationship between the starting component levels and the hydrate assemblages that develop during the curing process. Blast furnace-slag levels of 60, 45 and 30 wt.% were studied in blends containing fly ash and Portland cement. Geochemical modelling described the dissolution of the clinker, and predicted quantitatively the amount of hydrates. In all cases the experiments showed the presence of C-S-H, portlandite and ettringite. The quantities of ettringite, portlandite and the amorphous phases as determined by XRD agreed well with the calculated amounts of these phases after different periods of time. These findings show that changes in the bulk composition of hydrating cements can be described by geochemical models. Such a comparison between experimental and modelled data helps to understand in more detail the active processes occurring during cement hydration.

Presence of arsenic in different types of MTA and white and gray Portland cement.

Science.gov (United States)

Monteiro Bramante, Clóvis; Demarchi, Ana Claudia Cardoso Oliveira; de Moraes, Ivaldo Gomes; Bernadineli, Norberti; Garcia, Roberto Brandão; Spångberg, Lars S W; Duarte, Marco Antonio Hungaro

2008-12-01

The presence of arsenic in various types of mineral trioxide aggregate (MTA) and Portland cements were evaluated to verify if they comply with the ISO-recommended limit for water-based cements of 2 mg arsenic/kg material. An amount of 5 mL of hydrochloric acid was added to 2 g each of MTA and Portland cement to be analyzed. After 15 minutes, the material was filtered and the volume of supernatant was diluted with reagent-grade water up to 40 mL. Atomic absorption spectrophotometry readings were performed in triplicate. The following mean values were obtained: CPM (Egeo, Buenos Aires, Argentina) 11.06 mg/kg; CPM sealer (Egeo) 10.30 mg/kg; MTA-Obtura (Angelus, Londrina, PR, Brazil) 0.39 mg/kg; Experimental MTA: 10.30 mg/kg; White MTA-Angelus (Angelus) 1.03 mg/kg; Gray MTA-Angelus (Angelus) 5.91 mg/kg; ProRoot-MTA (Dentsply/Tulsa Dental Specialties, Tulsa, OK) 5.25 mg/kg; Gray Portland cement (Votorantim Cimentos, Cubatão, SP, Brazil): 34.27 mg/kg; and White Portland cement (Cimento Rio Branco, Rio de Janeiro, RJ, Brazil) 0.52 mg/kg. All tested materials presented arsenic in their composition. The form of arsenic was not analyzed nor the toxicity of the arsenic found. Only MTA-Obtura, White MTA-Angelus, and White Portland cement presented arsenic levels below the limit set in the ISO 9917-1 standard.

Effect of three natural pozzolans in portland cement hydration

Directory of Open Access Journals (Sweden)

Rahhal, V.

2003-03-01

Full Text Available Natural pozzolans have been used since ancient times and continues to be used today. The chemistry and morphological composition of natural pozzolans and their particle size distribution allows classifying them as more or less reactive pozzolan. In this research several techniques have been used to study the influence of pozzolan on portland cement hydration as much as to evaluate the mechanical and durable properties of concretes, mortars and pastes containing pozzolans. This paper describes the effect of incorporating three natural pozzolans to two cements with very different mineralogical composition. The techniques used were: conduction calorimetry and Fratini test. Results proved that pozzolanic activity and the acceleration and retardation of hydration reaction depend on the mineralogical composition of the portland cernent used. Effects of dilution, stimulation, acceleration or retardation reactions, behavior into areas of heat dissipation and pozzolanic activity depend on the percentage of pozzolan used and the age in which it has been analyzed.

El uso de las puzolanas naturales se remonta a la antigüedad, no obstante, actualmente continúa su utilización. La composición química y morfológica de las puzolanas naturales, sumado al tamaño de sus partículas, las califican como más o menos reactivas. En el estudio de las mismas, se han aplicado variadas técnicas para el análisis de sus interferencias en las reacciones de hidratación de los cementos portland; así como para la evaluación de las propiedades resistentes y duraderas que pueden conferirle a los hormigones, morteros o pastas de los que formen parte. Este trabajo versará sobre los efectos que produce la incorporación de tres puzolanas naturales a dos cementos portland de muy diferente composición mineralógica. Las técnicas aplicadas para su estudio han sido: la calorimetría de conducción y el ensayo de Fratini. Los resultados obtenidos permiten determinar

Research on the nanolevel influence of surfactants on structure formation of the hydrated Portland cement compositions

Directory of Open Access Journals (Sweden)

Guryanov Alexander

2016-01-01

Full Text Available The research of the structure formation process on a nanolevel of the samples of hydrated Portland cement compositions containing the modifying additives has been conducted with the help of small angle neutron scattering method. Carbonate and aluminum alkaline slimes as well as the complex additives containing surfactants were used as additives. The influence of slimes and surfactants on structural parameters change of Portland cement compositions of the average size of the disseminating objects, fractal dimension samples is considered. These Portland cement compositions are shown to be fractal clusters.

A randomized clinical trial on the use of medical Portland cement, MTA and calcium hydroxide in indirect pulp treatment.

Science.gov (United States)

Petrou, Marina Agathi; Alhamoui, Fadi Alhaddad; Welk, Alexander; Altarabulsi, Mohammed Basel; Alkilzy, Mohammed; H Splieth, Christian

2014-01-01

Studies on indirect pulp treatment (IPT) show varying success rates of 73 to 97 %. The necessity of re-opening the cavity and the question of the optimal capping material is still under debate. The aim of this prospective in vivo study was to compare the clinical and microbiological outcomes of mineral trioxide aggregate (MTA), medical Portland cement, and calcium hydroxide on the dentin-pulp complex of permanent and primary teeth treated with two-step IPT. In 86 regular patients (51 % men; 49 % women; age 17.2 years ±13.8), one deep carious lesion each was treated with incomplete caries removal, randomly selected capping with either calcium hydroxide (n = 31), medical Portland cement (29) or white MTA (26), and re-entry (6.3 months ±1.0). Clinical (color, humidity, and consistency of dentin) and microbiological (Lactobacilli/Mutans Strep. counts) parameters were recorded at the first and second treatment. The IPT had a high success rate of 90.3 % regardless of the material used (p = 0.72). The arrested lesions showed consistently darker, dry, and therefore, sclerotic dentine (p Portland cement. The findings of this study could promote the improvement of the IPT as a one-step treatment of deep carious lesions when the remaining demineralized dentin would be sealed with durable restorations.

Partial replacement of Portland cement by red ceramic waste in mortars: study of pozzolanic activity

International Nuclear Information System (INIS)

Silva, A.R. da; Cabral, K.C.; Pinto, E.N. de M.G.l.

2016-01-01

The objective of this study is to analyze the pozzolanic activity of red ceramic residue on the partial replacement of Portland cement in mortars. The mortars were prepared by substituting 25% of the Portland cement for ground of ceramic residue with water cement’s factor of 0.48. The concrete used to construct the reference mortars and those with addiction was CPII-Z-32 (compound of Portland pozzolana cement). The chemical analysis and physical ceramic waste showed that this meets the requirements of NBR12653 (2014) for use as pozzolanic material. The pozzolanic activity index (IAP) obtained for the ceramic waste to twenty-eight days cure rate was 80.28%. (author)

Root perforations treatment using mineral trioxide aggregate and Portland cements.

Science.gov (United States)

Silva Neto, José Dias da; Brito, Rafael Horácio de; Schnaider, Taylor Brandão; Gragnani, Alfredo; Engelman, Mírian; Ferreira, Lydia Masako

2010-12-01

Clinical, radiological and histological evaluation of root perforations treated with mineral trioxide aggregate (MTA) or Portland cements, and calcium sulfate barrier. One molar and 11 premolar teeth of a male mongrel dog received endodontic treatment and furcations were perforated with a high-speed round bur and treated with a calcium sulfate barrier. MTA, Portland cement type II (PCII) and type V (PCV), and white Portland cement (WPC) were used as obturation materials. The teeth were restored with composite resin and periapical radiographs were taken. The animal was euthanized 120 days post-surgery for treatment evaluation. Right lower first premolar (MTA), right lower third premolar (PCV), left lower second premolar (MTA), and right lower second premolar (WPC): clinically normal, slightly radio-transparent area on the furcation, little inflammatory infiltrate, and new-bone formation. Left lower third premolar (PCII), right upper first premolar (WPC), right upper third premolar (PCII), and left upper first molar (PCV): clinically normal, radiopaque area on the furcation, and new-bone formation. Right upper second premolar (MTA), left upper second premolar (WPC), left upper third premolar (PCII): presence of furcation lesion, large radiolucent area, and intense inflammatory infiltrate. All obturation materials used in this study induced new-bone formation.

Alternatieven voor Portland Cement in ontwikkelingslanden onderzocht : continue-kalkoven maakt toepassing van kalk pozzolaan cement mogelijk

NARCIS (Netherlands)

Egmond - de Wilde De Ligny, van E.L.C.; Jongsma, Ivo

1995-01-01

In de discussie over bouwmaterialen in ontwikkelingslanden wordt vaak gepleit voor alternatieven voor Portland Cement. De productie van Portland Cement is kapitaal- en energie-intensief en draagt weinig bij aan de ontwikkeling van deze landen. De klein schaliger productie van alternatieven voor

Exploratory characterization of volcanic ash sourced from Uganda as a pozzolanic material in portland cement concrete

NARCIS (Netherlands)

Buregyeya, A.; Quercia Bianchi, G.; Spiesz, P.R.; Florea, M.V.A.; Nassingwa, R.; Uzoegbo, H.C.; Schmidt, W.

2013-01-01

The need for alternative cementing materials to ordinary Portland cement (OPC) has promoted characterization research on pozzolana as an important ingredient in cement production. In Uganda, natural pozzolana application in cement production is done by only two producers of Portland cement and at a

T. rex and Godzilla: Finding Science in Science Fiction

Science.gov (United States)

Engelmann, G. F.; Chure, D. J.

2017-12-01

Works of fiction act as a powerful vehicle for inculcating an intuitive understanding (or misunderstanding) of scientific concepts in the audience. They can communicate information about scientific phenomena or how science is done. These entertainments can contribute to scientific literacy of the public and provide valuable outreach opportunities, but scientific accuracy is rarely even a minor consideration in developing fictional stories. Science educators can still make use of popular fiction to promote science education and outreach. Varied approaches have focused on the physical science in classic space operas, but historical sciences can make use of public interest in fictional tales involving prehistoric creatures and settings. Dinosaurs like T. rex inspire awe and widespread popular appeal that can nurture an interest in fossils but also serves as a gateway to all the other sciences on which paleontology depends, and to the scientific endeavor itself. But the portrayal of dinosaurs has met with negative criticism of details that is not likely to be productive of further discussion and learning. Perhaps it is not so important that authors and film makers didn't get it right; that "correctness" of terms and reconstructions is less important than the opportunity to improve public understanding of how science works; to cultivate a habit of critical thinking and an analytical approach to interpreting the world. Dinosaurs and other long extinct creatures can provide examples of how we know what we know; what kind of evidence is available and how it can be interpreted; how creative framing of hypotheses allows imaginative conjectures to be constrained by observations. They can open informative discussions of how scientists work in gathering data and developing and testing hypotheses. For example, how do paleontologists find fossils? Monsters, unrealistic fantasy creatures like Godzilla, have great charismatic appeal, and can prompt discussions of the obstacles

Physical and Thermodynamical Properties of Water Phases in Hardening Portland Cement Systems

DEFF Research Database (Denmark)

Hansen, T. Bæk

The present study is devoted to the description of water phases in hardening portland cement paste systems containing a significant amount of micro-filler and having a low to moderate water/powder ratio. Emphasis has been placed on the early stages of the hardening process.......The present study is devoted to the description of water phases in hardening portland cement paste systems containing a significant amount of micro-filler and having a low to moderate water/powder ratio. Emphasis has been placed on the early stages of the hardening process....

City of Portland: Businesses for an environmentally sustainable tomorrow

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-01

The sustainable business development program in Portland (OR) is known as BEST. BEST stands for Businesses for an Environmentally Sustainable Tomorrow. The Portland Energy Office operates BEST as a {open_quotes}one-stop service center{close_quotes} for business owners and managers. BEST provides information and assistance on resource efficient buildings and business practices. The results of BEST`s two years of operation have been generally impressive. Nearly 150 new or expanding businesses have been connected with utility design assistance programs. Businesses have also received assistance with water conservation, telecommuting, construction debris recycling, and alternative fuel vehicles. BEST has received local and national publicity and BEST services have been the topic at more than a dozen conferences, meetings, or other speaking engagements. A guidebook for communities wishing to start a similar program will be available in early 1996.

Structure investigations on Portland cement paste by small angle neutron scattering

International Nuclear Information System (INIS)

Dragolici, C.A.; Lin, A.

2004-01-01

Hydrated Portland cement is a very complex material. Cement paste consists of many crystalline and non-crystalline phases in various ranges of sizes (μm and nm scale). The crystalline phases are embedded in amorphous phases of hydration products. We investigated the structural changes of hydrating phases in a time interval up to 18 days, at Budapest Neutron Center's SANS spectrometer. The small angle neutron scattering of Portland cements prepared with a various water-to-cement ratios, gave us information about the microstructure changes in the material. Fractals were a suitable way for structure modelling. Some comments regarding the opportunity of using the most common models are pointed out. (authors)

Reaction of rat subcutaneous tissue to mineral trioxide aggregate and Portland cement: a secondary level biocompatibility test.

Science.gov (United States)

Karanth, P; Manjunath, M K; Kuriakose, E S

2013-01-01

This secondary-level animal study was conducted to assess and compare the subcutaneous tissue reaction to implantation of white mineral trioxide aggregate (MTA) and white Portland cement. Polyethylene tubes filled with either freshly mixed white MTA (Group I) or white Portland cement (Group II) were implanted subcutaneously into 12 Wistar Albino rats. Each animal also received an empty polyethylene tube as the control (Group III). After 7, 14, 21 and 30 days, the implants, together with surrounding tissues were excised. Two pathologists blinded to the experimental procedure, evaluated sections taken from the biopsy specimens for the severity of the inflammatory response, calcification and the presence and thickness of fibrous capsule surrounding the implant. Statistical analysis was performed using the Cross-tabs procedure, Univariate analysis of the variance two-way and the Pearson product moment correlation to assess inter-rater variability between the two evaluators. At 7 days, there was no significant difference in the severity of inflammation between the control group, white MTA, and white Portland cement groups. In the 14 day, 21 day and 30 day test periods, control group had significantly less inflammation than white MTA and white Portland cement. There was no significant difference in the grading of inflammation between white MTA and white Portland cement. All materials exhibited thick capsule at 7 days and thin capsule by 30 days. Both white MTA and white Portland cement were not completely non-irritating at the end of 30 days as evidenced by the presence of mild inflammation. However, the presence of a thin capsule around the materials, similar to the control group, indicates good tissue tolerance. White MTA and white Portland cement seem to be materials of comparable biocompatibility.

EnviroAtlas - Portland, ME - BenMAP Results by Block Group

Data.gov (United States)

U.S. Environmental Protection Agency — This EnviroAtlas dataset demonstrates the effect of changes in pollution concentration on local populations in 146 block groups in Portland, Maine. The US EPA's...

EnviroAtlas - Portland, OR - BenMAP Results by Block Group

Data.gov (United States)

U.S. Environmental Protection Agency — This EnviroAtlas dataset demonstrates the effect of changes in pollution concentration on local populations in 1176 block groups in Portland, Oregon. The US EPA's...

Assessment of Pollution Potentialities of some Portland Cement ...

African Journals Online (AJOL)

Chemical analysis of some Portland cement commonly used in Nigeria was carried out. All the cement studies were found to be good for concrete work especially where no special property is required. The concentration levels of heavy metals in all the cement samples were above the tolerance limit and therefore need to ...

76 FR 12370 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-Portland Cement...

Science.gov (United States)

2011-03-07

... Production Act of 1993--Portland Cement Association Notice is hereby given that, on February 02, 2011... seq. (``the Act''), Portland Cement Association (``PCA'') has filed written notifications..., Praxair, Danbury, CT; Metso Minerals, York, PA; Lehigh Cement Company LLC, Allentown, PA; Lehigh Northwest...

76 FR 34252 - Notice Pursuant to the National Cooperative Research and Production Act of 1993; Portland Cement...

Science.gov (United States)

2011-06-13

... Production Act of 1993; Portland Cement Association Notice is hereby given that, on May 12, 2011, pursuant to.... (``the Act''), Portland Cement Association (``PCA'') has filed written notifications simultaneously with... plaintiffs to actual damages under specified circumstances. Specifically, Drake Cement, LLC, Scottsdale, AZ...

Utilizing Science to Ensure Safe Access to Cultural Resources on Public Lands: The Portland Native American Community and Traditional Gathering of Camas

Science.gov (United States)

Greene, C.

2017-12-01

Native Americans have been conducting and contributing to science for millenia. We have observed nature and passed on evidence-based Traditional Ecological Knowledge (TEK) from generation to generation. Prior to colonization, this knowledge enabled our people to live with ample nutritional resources. Our long-standing relationship to nature continues today in tribal, rural, and urban communities, yet access to cultural resources (traditional food and medicines) proves challenging due to modern land management practices. The Native American community and public land managers in Portland, Oregon are addressing this challenge through the restoration of cultural resources across the landscape. One focus in these efforts is the camas plant (Camssia quamash), which grows in wetland and prairie ecosystems. The harvested bulbs are traditionally pit roasted, converting the indigestible inulin into carbohydrates of high nutritional value. Access to local natural areas has been granted for Native American community members to gather camas, yet pesticide and herbicide application as land management practices have created uncertainty regarding the safety of ingesting the camas bulbs. The Native American community gathered camas bulbs in November 2015 for analysis, which resulted in glyphosate (pesticide) and triclopyr (herbicide). There are various factors which may influence the uptake of pesticide and herbicide residuals in camas which need further investigation, including pesticide/herbicide application details (date, location), preferential uptake of pesticide/herbicides in camas among the present plant community, the impact of pit roasting bulbs on residuals, and traditional land management practices like prescribed burning. Utilizing TEK and science to ensure safe access to cultural resources is paramount in preserving our cultures and enhancing the value of indigenous perspectives on land management practices and policies.

Structure investigations on Portland cement paste by small angle neutron scattering

International Nuclear Information System (INIS)

Dragolici, C. A.; Len, A.

2003-01-01

Portland cement pastes consist of many crystalline and non-crystalline phases in various ranges of sizes (nm and mm scale). The crystalline phases are embedded in amorphous phases of the hydration products. We investigated the structural changes of hydrating phases in the time interval of 1-30 days at Budapest Neutron Center's SANS diffractometer. The small angle neutron scattering of Portland cements prepared with a water-to-cement ratio from 0,3 to 0,8 gave us information about the microstructure changes in the material. Fractals were a suitable way for structure modelling. The variation of fractals size depending on the preparation-to-measurement time interval and water-to-cement ratio could be observed. (authors)

The Social Acceptance of Community Solar: A Portland Case Study

Science.gov (United States)

Weaver, Anne

Community solar is a renewable energy practice that's been adopted by multiple U.S. states and is being considered by many more, including the state of Oregon. A recent senate bill in Oregon, called the "Clean Electricity and Coal Transition Plan", includes a provision that directs the Oregon Public Utility Commission to establish a community solar program for investor-owned utilities by late 2017. Thus, energy consumers in Portland will be offered participation in community solar projects in the near future. Community solar is a mechanism that allows ratepayers to experience both the costs and benefits of solar energy while also helping to offset the proportion of fossil-fuel generated electricity in utility grids, thus aiding climate change mitigation. For community solar to achieve market success in the residential sector of Portland, ratepayers of investor-owned utilities must socially accept this energy practice. The aim of this study was to forecast the potential social acceptance of community solar among Portland residents by measuring willingness to participate in these projects. Additionally, consumer characteristics, attitudes, awareness, and knowledge were captured to assess the influence of these factors on intent to enroll in community solar. The theory of planned behavior, as well as the social acceptance, diffusion of innovation, and dual-interest theories were frameworks used to inform the analysis of community solar adoption. These research objectives were addressed through a mixed-mode survey of Portland residents, using a stratified random sample of Portland neighborhoods to acquire a gradient of demographics. 330 questionnaires were completed, yielding a 34.2% response rate. Descriptive statistics, binomial logistic regression models, and mean willingness to pay were the analyses conducted to measure the influence of project factors and demographic characteristics on likelihood of community solar participation. Roughly 60% of respondents

75 FR 4423 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-Portland Cement...

Science.gov (United States)

2010-01-27

... Production Act of 1993--Portland Cement Association Notice is hereby given that, on December 14, 2009... seq. (``the Act''), Portland Cement Association (``PCA'') has filed written notifications... Cement, Hannibal, MO has been added as a party to this venture. Also, the following parties have...

Nanotechnology-Based Performance Improvements For Portland Cement Concrete - Phase I

Science.gov (United States)

2012-08-16

A fundamental understanding of the nano-structure of Portland cement concrete (PCC) is the key to realizing significant breakthroughs regarding high performance and susta : (MBTC 2095/3004) using molecular dynamics (MD) provided new understanding of ...

Study of the bismuth oxide concentration required to provide Portland cement with adequate radiopacity for endodontic use.

Science.gov (United States)

Bueno, Carlos Eduardo da Silveira; Zeferino, Eduardo Gregatto; Manhães, Luiz Roberto Coutinho; Rocha, Daniel Guimarães Pedro; Cunha, Rodrigo Sanches; De Martin, Alexandre Sigrist

2009-01-01

The purpose of this study was to determine the ideal concentration of bismuth oxide in white Portland cement to provide it with sufficient radiopacity for use as an endodontic material (ADA specification #57). 2-mm thick standardized test specimens of white MTA and of white Portland cement, as controls, and of white Portland cement with the experimental addition of 5%, 10%, 15%, 20%, 25% or 30% of bismuth oxide were radiographed and compared with various thicknesses of pure aluminum, using optic density to determine the observed grayscale levels of radiopacity in a scale ranging from 0 to 255. The data was submitted to ANOVA (pcement with 0%, 5%, 10%, 15%, 20%, 25% and 30% of bismuth oxide presented mean readings of 63.3, 95.7, 110.7, 142.7, 151.3, 161.0 and 180.0 respectively. MTA presented a mean reading of 157.3. The readings of MTA and white Portland cement with 15% bismuth oxide did not differ significantly from the reading observed for a thickness of 4 mm of aluminum (145.3), which is considered ideal for a test specimen by ADA specification #57 (2 mm above the thickness of the test specimen). White MTA and white Portland cement with 15% bismuth oxide presented the radiopacity required for an endodontic cement.

77 FR 5573 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-Portland Cement...

Science.gov (United States)

2012-02-03

... Production Act of 1993--Portland Cement Association Notice is hereby given that, on January 6, 2012, pursuant... seq. (``the Act''), Portland Cement Association (``PCA'') has filed written notifications..., Newark, DE, has been added as a party to this venture. Also, Texas-Lehigh Cement Company, Buda, TX...

Toxicity and Histopathological Effects of Portland Cement Powder in ...

African Journals Online (AJOL)

Hepatic lesions in the liver tissues of fish exposed to Portland cement powder in solution were characterized by degeneration of hepatocyte, vascuolization of cell cytoplasm, fatty degeneration and hypertrophy of hepatocytes. Histological comparison of tissues indicated that most damage occurred in the gill rather than in ...

Utilization of steel slag for Portland cement clinker production.

Science.gov (United States)

Tsakiridis, P E; Papadimitriou, G D; Tsivilis, S; Koroneos, C

2008-04-01

The aim of the present research work is to investigate the possibility of adding steel slag, a by-product of the conversion of iron to steel process, in the raw meal for the production of Portland cement clinker. Two samples of raw meals were prepared, one with ordinary raw materials, as a reference sample ((PC)(Ref)), and another with 10.5% steel slag ((PC)(S/S)). Both raw meals were sintered at 1450 degrees C. The results of chemical and mineralogical analyses as well as the microscopic examination showed that the use of the steel slag did not affect the mineralogical characteristics of the so produced Portland cement clinker. Furthermore, both clinkers were tested by determining the grindability, setting times, compressive strengths and soundness. The hydration products were examined by XRD analysis at 2, 7, 28 and 90 days. The results of the physico-mechanical tests showed that the addition of the steel slag did not negatively affect the quality of the produced cement.

Network Level Carbon Dioxide Emissions From On-road Sources in the Portland OR, (USA) Metropolitan Area

Science.gov (United States)

Powell, J.; Butenhoff, C. L.; Rice, A. L.

2014-12-01

To mitigate climate change, governments at multiple levels are developing policies to decrease anthropogenic carbon dioxide (CO2) emissions. The City of Portland (Oregon) and Multnomah County have adopted a Climate Action Plan with a stated goal of reducing emissions to 80% below 1990 levels by 2050. The transportation sector alone accounts for about 40% of total emissions in the Portland metropolitan area. Here we show a new street-level model of on-road mobile CO2 emissions for the Portland, OR metropolitan region. The model uses hourly traffic counter recordings made by the Portland Bureau of Transportation at 9,352 sites over 21 years (1986-2006), augmented with freeway loop detector data from the Portland Regional Transportation Archive Listing (PORTAL) transportation data archive. We constructed a land use regression model to fill in traffic network gaps with traffic counts as the dependent variable using GIS data such as road class (32 categories) and population density. The Environmental Protection Agency (EPA) MOtor Vehicle Emission Simulator (MOVES) model was used to estimate transportation CO2 emissions. The street-level emissions can be aggregated and gridded and used as input to atmospheric transport models for comparison with atmospheric measurements. This model also provides an independent assessment of top-down inventories that determine emissions from fuel sales, while being an important component of our ongoing effort to assess the effectiveness of emission mitigation strategies at the urban scale.

Radiopacity and histological assessment of Portland cement plus bismuth oxide.

Science.gov (United States)

Coutinho-Filho, Tauby; De-Deus, Gustavo; Klein, Leila; Manera, Gisele; Peixoto, Carla; Gurgel-Filho, Eduardo Diogo

2008-12-01

The present study evaluated the subcutaneous connective tissue reactions and the radiopacity of MTA, Portland cement (PC), and Portland cement plus bismuth oxide (BO). Forty rats were divided into 5 groups (n = 8 per group): A1: Control (empty capsule); A2: Pro-Root MTA; A3: PC; A4: PC + BO 1:1; and A5: PC + BO 2:1. Polyethylene tubes were filled with the test materials and standardized radiographic images were taken. Histological evaluation was done after 7 and 60 days. Student t test and Fisher's test were used in the statistical analysis (P A4 > A5 > A3. No differences were found for the tissue response in the 2 experimental periods. A positive correlation between BO concentration and radiopacity of PC was determined. The histological evaluation suggests that all studied materials were biocompatible at 7 and 60 days.

Comparative study of the properties of ordinary portland cement ...

African Journals Online (AJOL)

The study explored metakaolin as alternative material to cement. It compares the properties of Ordinary Portland Cement (OPC) concrete and binary concrete containing metakaolin as partial replacement of OPC. Two set of concrete samples; one with 10% Metakaolin (MK) replacing OPC by weight, and the other without ...

Resonance – Journal of Science Education | Indian Academy of ...

Indian Academy of Sciences (India)

David L Farrens1 Thomas P Sakmar2. Department of Biochemistry and Molecular Biology Oregon Health and Science University Portland OR 97239, USA. Head, Laboratory of Chemical Biology and Signal Transduction The Rockefeller University, 1230 York, Ave., New York, NY 10065, USA.

76 FR 50252 - Gray Portland Cement and Cement Clinker From Japan; Scheduling of an Expedited Five-Year Review...

Science.gov (United States)

2011-08-12

... INTERNATIONAL TRADE COMMISSION [Investigation No. 731-TA-461 (Third Review)] Gray Portland Cement and Cement Clinker From Japan; Scheduling of an Expedited Five-Year Review Concerning the Antidumping Duty Order on Gray Portland Cement and Cement Clinker From Japan AGENCY: United States International...

Ettringite and C-S-H Portland cement phases for waste ion immobilization: A review

International Nuclear Information System (INIS)

Gougar, M.L.D.; Scheetz, B.E.; Roy, D.M.

1996-01-01

The formation, structure and chemistry of the ettringite and C-S-H phases of Portland cement have been reviewed as they relate to waste ion immobilization. The purpose of this review was to investigate the use of Portland cement as a host for priority metallic pollutants as identified by the Environmental Protection Agency and as a host for radioactive waste ions as identified in 40 CFR 191. Ettringite acts as host to a number of these ions in both the columnar and channel sections of the crystal structure. Substitutions have been made at the calcium, aluminum, hydroxide and sulfate sites. C-S-H also hosts a number of the waste species in both ionic and salt form. Immobilization mechanisms for C-S-H include sorption, phase mixing and substitution. The following ions have not apparently been reported as specifically immobilized by one of these phases: Ag, Am, Np, Pu, Ra, Tc, Th and Sn; however, some of these ions are immobilized by Portland cement

Una nota sobre los Hormigones de Cemento Portland (HCP y Hormigones de Cemento Portland con Adiciones (HCPA

Directory of Open Access Journals (Sweden)

Talero Morales, Rafael

1993-09-01

Full Text Available El hombre contemporáneo ha dividido el proceso evolutivo de la humanidad en macroperíodos de tiempo relacionados con avances significativos obtenidos en el campo de los materiales. Así se define la edad de piedra, bronce, hierro, cobre, etc. Y siguiendo esta tendencia, probablemente las generaciones futuras podrán hablar de esta época como la "edad del hormigón" y mostrar los monumentales vestigios que, en su mayor parte, se han construido con hormigón de cemento portland.

Portland cement hydration in the presence of admixtures: black gram pulse and superplasticizer

Directory of Open Access Journals (Sweden)

Viveka Nand Dwivedi

2008-12-01

Full Text Available Effect of admixtures such as black gram pulse (BGP and sulfonated naphthalene based superplasticizer (SP on the hydration of Portland cement has been studied. The hydration characteristics of OPC in the presence of BGP and SP were studied with the help of non evaporable water content determinations, calorimetric method, Mössbauer spectroscopic and atomic force microscopic techniques. Results have shown that both BGP and SP get adsorbed at the surface of cement and its hydration products. The hydration of Portland cement is retarded in the presence of both the admixtures and nanosize hydration products are formed.

Clinical Science: showcasing the breadth of the journal.

Science.gov (United States)

Cooper, Mark E; Touyz, Rhian M

2017-07-15

This Editorial introduces the review articles published in this issue to showcase the range of subject areas, such as neurology, the respiratory system, kidney disease and oxidative stress, covered by Clinical Science . © 2017 The Author(s). Published by Portland Press Limited on behalf of the Biochemical Society.

Experimental and modeling study of Portland cement paste degradation in boric acid

International Nuclear Information System (INIS)

Benakli, A.; Chomat, L.; Le Bescop, P.; Wall, J.

2015-01-01

In the framework of Spent Fuel Pools (SFP) lifetime studies, an investigation of the Portland cement degradation in boric acid has been requested by the Electric Power Research Institute. The main goal of this study is to identify the physico-chemical degradation mechanisms involved in boric acid media. Both experimental and modeling approaches are considered. Concerning degradation experiments, sample of cement paste are immersed during three and nine months in a boric acid solution at 2400 ppm that is periodically renewed. Boric acid concentration has been chosen to be representative of SFP solution. Results will be confronted with reactive transport numerical calculations performed by the reactive transport code HYTEC associated with a dedicated extended database called Thermoddem. The analysis of degradation solution revealed a main ions release mechanism driven by diffusion especially for calcium, nitrate, sodium and sulfate. Leaching behavior of magnesium seems to be more complex. Decalcification is the major degradation process involved, even if a non-negligible contribution of further cations (Mg 2+ , Na + ) and anions (SO 4 2- ) has been noticed. Analysis of degradation soution also revealed that kinetic of Portland cement paste degradation in boric acid is higher than in pure water, regarding the degraded depths measured and calcium leaching rate. This observation has been confirmed by solid characterization. Microstructure analysis of degraded Portland cement paste showed a global porosity increase in the degraded zone that might be mainly attributed to Portlandite dissolution. An Ettringite reprecipitation in the degraded zone has been suspected but could also be Ettringite-like phases containing boron. The analysis techniques used did not allow us to differentiate it, and no others specific mineral phases containing boron has been identified. Profile pattern by XRD analysis allowed us to identify four zones composing the degraded Portland cement paste

Global Science and Social Systems: The Essentials of Montessori Education and Peace Frameworks

Science.gov (United States)

Kahn, David

2016-01-01

Inspired by Baiba Krumins-Grazzini's interdependencies lecture at NAMTA's Portland conference, David Kahn shows the unifying structures of the program that are rooted in the natural and social sciences. Through a connective web, these sciences explore the integration of all knowledge and lead to a philosophical view of life on earth, including…

Use of red mud as addition for portland cement mortars

International Nuclear Information System (INIS)

Ribeiro, D.V.; Morelli, M.R.

2011-01-01

The aim of the present research work was to investigate the possibility of adding red mud, an alkaline leaching waste that is obtained from bauxite during the Bayer process for alumina production, in the raw meal of Portland cement mortars. The red mud is classified as dangerous, according to NBR 10004/2004, and world while generation reached over 117 million tons/year. This huge production requires high consuming products to be used as incorporation matrix and we studied the influence of red mud addition on the characteristics of cement mortars and concrete. In this paper the properties of Portland cement mortars incorporating high amounts of red mud was evaluated: pH variation, fresh (setting time, workability or normal consistency and water retention), and hardened state (mechanical strength, capillary water absorption, density and apparent porosity). Results seem promising for red mud additions up to 20 wt%. (author)

Study of irradiation damage by fast neutrons in samples of Portland cement

International Nuclear Information System (INIS)

Lucki, G.; Rosa Junior, A.A.

1984-01-01

The effect of neutron irradiation in samples of Portland cement was evaluated, using the resonance frequency method and pulse velocity of ultra-sound techniques. The samples were divided in three groups: 1) monitoring samples; 2) samples submitted to gamma heating; 3) Irradiated samples. In the sample preparation, it was used the Portland Santa Rita CP 320 cement, and water-cement rate of 0.40 l/Kg. The irradiation was done in the research reactor IEA-R1, at IPEN - CNEN/SP, with an integrated flux of 7.2 x 10 18 n/cm 2 (E approx. 1 MeV). Some damage were detected, due to the neutron flux, and by the thermal effect of gamma heating. (E.G.) [pt

Hydration kinetics modeling of Portland cement considering the effects of curing temperature and applied pressure

International Nuclear Information System (INIS)

Lin Feng; Meyer, Christian

2009-01-01

A hydration kinetics model for Portland cement is formulated based on thermodynamics of multiphase porous media. The mechanism of cement hydration is discussed based on literature review. The model is then developed considering the effects of chemical composition and fineness of cement, water-cement ratio, curing temperature and applied pressure. The ultimate degree of hydration of Portland cement is also analyzed and a corresponding formula is established. The model is calibrated against the experimental data for eight different Portland cements. Simple relations between the model parameters and cement composition are obtained and used to predict hydration kinetics. The model is used to reproduce experimental results on hydration kinetics, adiabatic temperature rise, and chemical shrinkage of different cement pastes. The comparisons between the model reproductions and the different experimental results demonstrate the applicability of the proposed model, especially for cement hydration at elevated temperature and high pressure.

Ecological indices of manufacture of Portland cement clinker and production of the dolomite clinker

Directory of Open Access Journals (Sweden)

Vinnichenko Varvara

2017-01-01

Full Text Available It is shown that the production of dolomite clinker in comparison with that of Portland cement is environmentally appropriate. When calcining dolomite for cementitious binder, the pollution of the atmosphere by carbon dioxide is reduced due to its isolation during decarbonization reactions of calcium carbonates. Reducing fuel consumption for clinker burning provides less carbon dioxide emissions from combustion products. Reducing the firing temperature creates obstacles to the formation of nitrogen oxides. The production of binders from dolomite in comparison with the production of Portland cement helps to protect the environment from contamination

Regional economic impact assessment: Evaluating remedial alternatives for the Portland Harbor Superfund Site, Portland, Oregon, USA.

Science.gov (United States)

Harrison, David; Coughlin, Conor; Hogan, Dylan; Edwards, Deborah A; Smith, Benjamin C

2018-01-01

The present paper describes a methodology for evaluating impacts of Superfund remedial alternatives on the regional economy in the context of a broader sustainability evaluation. Although economic impact methodology is well established, some applications to Superfund remedial evaluation have created confusion because of seemingly contradictory results. This confusion arises from failure to be explicit about 2 opposing impacts of remediation expenditures: 1) positive regional impacts of spending additional money in the region and 2) negative regional impacts of the need to pay for the expenditures (and thus forgo other expenditures in the region). The present paper provides a template for economic impact assessment that takes both positive and negative impacts into account, thus providing comprehensive estimates of net impacts. The paper also provides a strategy for identifying and estimating major uncertainties in the net impacts. The recommended methodology was applied at the Portland Harbor Superfund Site, located along the Lower Willamette River in Portland, Oregon, USA. The US Environmental Protection Agency (USEPA) developed remedial alternatives that it estimated would cost up to several billion dollars, with construction durations possibly lasting decades. The economic study estimated regional economic impacts-measured in terms of gross regional product (GRP), personal income, population, and employment-for 5 of the USEPA alternatives relative to the "no further action" alternative. Integr Environ Assess Manag 2018;14:32-42. © 2017 The Authors. Integrated Environmental Assessment and Management published by Wiley Periodicals, Inc. on behalf of Society of Environmental Toxicology & Chemistry (SETAC). © 2017 The Authors. Integrated Environmental Assessment and Management published by Wiley Periodicals, Inc. on behalf of Society of Environmental Toxicology & Chemistry (SETAC).

Influencia del yeso sobre la velocidad de hidratación del cemento portland

Directory of Open Access Journals (Sweden)

Yamaguchi, G.

1961-12-01

Full Text Available Not availablePara esclarecer la Influencia del yeso sobre el fraguado y endurecimiento del cemento, los autores estudiaron el grado de hidratación de los cuatro principales minerales del clínker de cemento Portland y el efecto del yeso sobre ellas. Haciendo uso del análisis cuantitativo de rayos X, se determinó la porción no hidratada. Simultáneamente, se determinaron los tiempos de fraguado y las resistencias. Los ensayos se llevaron a cabo sobre tres clínkeres sintéticos de diferentes composiciones y sobre dos clínkeres de cemento Portland comerciales.

Rheological Properties of Very High-Strength Portland Cement Pastes: Influence of Very Effective Superplasticizers

Directory of Open Access Journals (Sweden)

Adriano Papo

2010-01-01

Full Text Available The influence of the addition of very effective superplasticizers, that are commercially available, employed for maximising the solid loading of very high-strength Portland cement pastes, has been investigated. Cement pastes were prepared from deionized water and a commercially manufactured Portland cement (Ultracem 52.5 R. Cement and water were mixed with a vane stirrer according to ASTM Standard C305. The 0.38 to 0.44 water/cement ratio range was investigated. Three commercial superplasticizing agents produced by Ruredil S.p.a. were used. They are based on a melamine resin (Fluiment 33 M, on a modified lignosulphonate (Concretan 200 L, and on a modified polyacrylate (Ergomix 1000. Rheological tests were performed at 25°C by using the rate controlled coaxial cylinder viscometer Rotovisko-Haake 20, system M5-osc., measuring device MV2P with serrated surfaces. The tests were carried out under continuous flow conditions. The results of this study were compared with those obtained in a previous article for an ordinary Portland cement paste.

Thermodynamic modelling of the effect of temperature on the hydration and porosity of Portland cement

International Nuclear Information System (INIS)

Lothenbach, Barbara; Matschei, Thomas; Moeschner, Goeril; Glasser, Fred P.

2008-01-01

The composition of the phase assemblage and the pore solution of Portland cements hydrated between 0 and 60 deg. C were modelled as a function of time and temperature. The results of thermodynamic modelling showed a good agreement with the experimental data gained at 5, 20, and 50 deg. C. At 5 and at 20 deg. C, a similar phase assemblage was calculated to be present, while at approximately 50 deg. C, thermodynamic calculations predicted the conversion of ettringite and monocarbonate to monosulphate. Modelling showed that in Portland cements which have an Al 2 O 3 /SO 3 ratio of > 1.3 (bulk weight), above 50 deg. C monosulphate and monocarbonate are present. In Portland cements which contain less Al (Al 2 O 3 /SO 3 < 1.3), above 50 deg. C monosulphate and small amounts of ettringite are expected to persist. A good correlation between calculated porosity and measured compressive strength was observed

STABILISASI TANAH LIAT SANGAT LUNAK DENGAN GARAM DAN PC (PORTLAND CEMENT

Directory of Open Access Journals (Sweden)

Tirta Djusman Arief

2006-01-01

Full Text Available Adding sodium chloride, as admixture, and Portland Cement, as stabilizer, to a very soft clay increase its plasticity index (PI, Californian Bearing Ratio (CBR, and Unconfined Compression Strength (UCS. This paper presents the results of testings done to very soft clay from Margomulyo, Surabaya. The results show a promising tendency. Anyhow a wider and comprehensive research is still needed to ensure the long-term effect of the soil stabilization. Abstract in Bahasa Indonesia : Penambahan garam (sodium chloride dan PC (Portland Cement meningkatkan PI (Plasticity Index, CBR (Californian Bearing Ratio, dan UCS (Unconfined Compression Strength dari tanah lempung sangat lunak. Dalam makalah ini disajikan hasil pengujian yang dilakukan terhadap lempung sangat lunak dari daerah Margomulyo, Surabaya. Hasilnya menunjukkan kecenderungan yang menggembirakan, namun penelitian yang luas dan komprehensif masih diperlukan untuk peningkatan stabilitas tanah dalam jangka panjang.

Ex vivo assessment of genotoxicity and cytotoxicity in murine fibroblasts exposed to white MTA or white Portland cement with 15% bismuth oxide.

Science.gov (United States)

Zeferino, E G; Bueno, C E S; Oyama, L M; Ribeiro, D A

2010-10-01

To evaluate whether white mineral trioxide aggregate (MTA) or white Portland cement with 15% bismuth oxide were able to induce genetic damage and cellular death ex vivo. Aliquots of 1 × 10(4) murine fibroblasts were incubated at 37 °C for 3 h with MTA (white) or white Portland cement with 15% bismuth oxide, at final concentrations ranging from 10 to 1000 μg mL(-1) individually. Data of three independent repeats from the comet assay and the trypan blue exclusion test were assessed by the one-way anova followed by Tukey's test. Mineral trioxide aggregate or Portland cement containing bismuth oxide did not produce genotoxic effects with respect to the single-cell gel (comet) assay data for all concentrations evaluated. Furthermore, no cytotoxicity was observed for MTA or Portland cement. White MTA or white Portland cement containing 15% bismuth oxide were not genotoxic and cytotoxic. © 2010 International Endodontic Journal.

EnviroAtlas - Portland, ME - Meter-Scale Urban Land Cover (MULC) Data (2010)

Data.gov (United States)

U.S. Environmental Protection Agency — The EnviroAtlas Portland, ME Meter-Scale Urban Land Cover (MULC) data was generated from USDA NAIP (National Agricultural Imagery Program) four band (red, green,...

INFLUENCE OF BARIUM OXIDE ADDITIONS ON PORTLAND CLINKER

Directory of Open Access Journals (Sweden)

Anezka Zezulova

2016-12-01

Full Text Available Nowadays, nuclear power plants are widespread around the world and research is of great interest. Together with nuclear research, shielding of different types of radiation is an important current topic of research aiming at their safety. Portland cement has been an elementary building material for centuries. Since barium is very efficient in shielding different types of radiation, it can be assumed that the radiation shielding capability of cement can be improved by incorporation of barium. This work deals with the influence of barium oxide, added in the form of barium carbonate and sulphate, on the formation and properties of Portland clinker. The structure of burnt clinkers and the ratio of clinker phases were studied by polarizing microscopy and by X-ray diffraction. With increasing barium content, the alite-belite ratio decreases and the content of free lime gradually increases. Moreover, sulphates induce the growth of alite crystals. The ability of barium to be a part of the clinker minerals was observed by scanning electron microscopy. Belite and clinker melt contain the highest amount of barium, but aggregates of barium oxide are formed in the clinker melt. Furthermore, the rate of alite crystallization was studied under isothermal conditions.

Setting time and flowability of accelerated Portland cement mixed with polycarboxylate superplasticizer.

Science.gov (United States)

Wongkornchaowalit, Norachai; Lertchirakarn, Veera

2011-03-01

Important limitations of mineral trioxide aggregate for use in clinical procedures are extended setting time and difficult handling characteristics. The removal of gypsum at the end stage of the Portland cement manufacturing process and polycarboxylate superplasticizer admixture may solve these limitations. Different concentrations of polycarboxylate superplasticizer (0%, 1.2%, 1.8%, and 2.4% by volume) and liquid-to-powder ratios (0.27, 0.30, and 0.33 by weight) were mixed with white Portland cement without gypsum (AWPC-experimental material). Type 1 ordinary white Portland cement mixed with distilled water at the same ratios as the experimental material was used as controls. All samples were tested for setting time and flowability according to the International Organization for Standardization 6876:2001 guideline. The data were analyzed by two-way analysis of variance. Then, one-way analysis of variance and multiple comparison tests were used to analyze the significance among groups. The data are presented in mean ± standard deviation values. In all experimental groups, the setting times were in the range of 4.2 ± 0.4 to 11.3 ± 0.2 minutes, which were significantly (p setting time and increased flowability of cement, which would be beneficial for clinical use. Copyright © 2011 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

In Vitro Bioactivity and Setting Times of White Portland Cement Combined with Different Radio Pacifying Agents

Directory of Open Access Journals (Sweden)

Coleman Nichola Jayne

2017-01-01

Full Text Available Commercial formulations based on 80:20 mixtures of Portland cement and bismuth oxide (a radiopacifying agent are used in dentistry as root-filling materials. This study compares the impact of two alternative radiopacifiers, barium sulphate and zirconium oxide, with that of bismuth oxide, on the setting times and bioactivity of white Portland cement. The findings indicate that bismuth oxide prolongs both the initial and final setting times of the cement, and that barium sulphate and zirconium oxide have no effect on this parameter. Hydroxyapatite (HA formed on the surfaces of all test samples within 7 days of exposure to simulated body fluid, indicating that they possess the potential to stimulate new hard tissue formation. Fourier transform infrared spectroscopy, the traditional technique for the identification of HA, was not appropriate for the analysis of these cement systems owing to the overlap of signals from each of the radiopacifiers with the characteristic P-O bending modes of HA in the 570 – 610 cm−1 region. In this respect, the P-O band at 965 cm−1 of HA in the Raman spectrum was found to be a suitable means of detection since it is discrete with respect to all signals arising from the radiopacifying agents and cement phases.

Improved quantification of alite and belite in anhydrous Portland cements by 29Si MAS NMR: Effects of paramagnetic ions

DEFF Research Database (Denmark)

Poulsen, Søren Lundsted; Kocaba, Vanessa; Le Saoût, Gwenn

2009-01-01

The applicability, reliability, and repeatability of 29Si MAS NMR for determination of the quantities of alite (Ca3SiO5) and belite (Ca2SiO4) in anhydrous Portland cement was investigated in detail for 11 commercial Portland cements and the results compared with phase quantifications based...

Using Art to Teach Students Science Outdoors: How Creative Science Instruction Influences Observation, Question Formation, and Involvement

Science.gov (United States)

Cone, Christina Schull

Elementary education has become increasingly divided into subjects and focused on the demand for high math and reading scores. Consequently, teachers spend less time devoted to science and art instruction. However, teaching art and science is crucial to developing creative and rational thinking, especially for observation and questioning skills. In this study, third grade students attending an urban school in Portland, Oregon received instruction of an art strategy using observational and quantifying drawing techniques. This study examines, "Will an art strategy observing the local environment help students make observations and ask questions?" and "In what ways are student learning and perspectives of science affected by the art strategy?" The independent variable is the art strategy developed for this study. There are three dependent variables: quality of student observations, quality of questions, and themes on student learning and perspectives of science. I predicted students would develop strong observation and questioning skills and that students would find the strategy useful or have an increased interest in science. The art scores were high for relevance and detail, but not for text. There were significant correlations between art scores and questions. Interviews revealed three themes: observations create questions, drawing is helpful and challenging, and students connected to science. By examining science through art, students were engaged and created strong observations and questions. Teachers need to balance unstructured drawing time with scaffolding for optimal results. This study provides an integrated science and art strategy that teachers can use outdoors or adapt for the classroom.

Finding science in students' talk

Science.gov (United States)

Yeo, Jennifer

2009-12-01

What does it mean to understand science? This commentary extends Brown and Kloser's argument on the role of native language for science learning by exploring the meaning of understanding in school science and discusses the extent that science educators could tolerate adulterated forms of scientific knowledge. Taking the perspective of social semiotics, this commentary looks at the extent that school science can be represented with other discourse practices. It also offers an example to illustrate how everyday language can present potential hindrance to school science learning.

Prediction of potential compressive strength of Portland clinker from its mineralogy

DEFF Research Database (Denmark)

Svinning, K.; Høskuldsson, Agnar; Justnes, H.

2010-01-01

Based on a statistical model first applied for prediction of compressive strength up to 28 d from the microstructure of Portland cement, potential compressive strength of clinker has been predicted from its mineralogy. The prediction model was evaluated by partial least squares regression...

Development of the Portland cement slurries with diatomaceous earth to the oil industry; Desenvolvimento de pastas de cimento Portland com adicao de diatomita para a industria do petroleo

Energy Technology Data Exchange (ETDEWEB)

Brito, Roseane A; Melo, Dulce M.A.; Martinelli, Antonio E.; Simao, Cristina A.; Paiva, Maria D.M. [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil); Melo, Marcus A.F. [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES)

2004-07-01

The class-G Portland cement has been used with success in oil well cementing. The material is usually shipped to the Northeast Brazil, because the only plant that manufactures class-G is located in Cantagalo/RJ. The present work investigates the influence of the partial substitution of Portland cement by diatomaceous earth, aiming at reducing the costs in oil well cementing, improving the slurry properties and using local raw material. The diatomaceous earth has pozzolanic properties and can be used as extenders of cement slurries. This properties added to the lower cost and availability of this material in Northeast Brazil, make the diatomaceous earth a candidate material to produce light cements, to well conditions in advanced phases of production. It were evaluated the rheological properties of the slurries (at 25 and 52 deg C), volume of free water, compressive strength after curing for 8, 24 and 48 h at 38 deg C, and consistometry tests. The results show that the diatomaceous earth maintain the viscosity values and gel force suitable for use in oil well cementing. No free water was observed in the formulations. It was also verified that the compressive strength of slurries hardened with diatomaceous earth is similar to those with only Portland cement and that the minimum compressive strength of 300 psi, after curing for 8 h was reached. The thickening time was longer than the average value and the application value. (author)

Production of portland cement using Moroccan oil shale and comparative study between conventional cement plant and cement plant using oil shale

International Nuclear Information System (INIS)

Doumbouya, M.; Kacemi, K.E.; Kitane, S.

2012-01-01

Like the use of coal ash from power plants as an addition to cement, oil shale are used for cement production on an industrial scale in Estonia, China, USA and Germany. Oil shale can be utilized in manufacturing the cement. In addition to the utilization of these by-products after combustion, it can also reduce the required temperature for the clinkering reactions during the production of Portland clinker. We performed a study on the Moroccan oil shale to maximize the use of oil shale ash in the manufacturing of Portland cement. We found that Moroccan oil shale ash can be used up to 30% with 70% Portland clinker without altering its principle properties. The corresponding temperature required to generate the required liquid for the clinkering reactions as well as the essential ingredients for clinker was found to be around 850 to 1000 deg. C. The operating temperatures for this optimized blend ratio were found to 1000 deg. C. The resulting Portland clinker from this ratio will need further testing in accordance with international standards for Portland cement to examine properties like strength and setting time. (author)

Final Rule: NESHAP for the Portland Cement Manufacturing Industry: Alternative Monitoring Method

Science.gov (United States)

EPA is extending its approval for the use of an alternative method to show compliance with hydrogen chloride (HCl) emissions limits in the National Emission Standards for Hazardous Air Pollutants for the Portland Cement Manufacturing Industry

High-volume natural volcanic pozzolan and limestone powder as partial replacements for portland cement in self-compacting and sustainable concrete

KAUST Repository

Celik, Kemal; Jackson, Marie D.; Mancio, Mauricio; Meral, Cagla; Emwas, Abdul-Hamid M.; Mehta, P. Kumar; Monteiro, Paulo José Meleragno

2014-01-01

A laboratory study demonstrates that high volume, 45% by mass replacement of portland cement (OPC) with 30% finely-ground basaltic ash from Saudi Arabia (NP) and 15% limestone powder (LS) produces concrete with good workability, high 28-day compressive strength (39 MPa), excellent one year strength (57 MPa), and very high resistance to chloride penetration. Conventional OPC is produced by intergrinding 95% portland clinker and 5% gypsum, and its clinker factor (CF) thus equals 0.95. With 30% NP and 15% LS portland clinker replacement, the CF of the blended ternary PC equals 0.52 so that 48% CO2 emissions could be avoided, while enhancing strength development and durability in the resulting self-compacting concrete (SCC). Petrographic and scanning electron microscopy (SEM) investigations of the crushed NP and finely-ground NP in the concretes provide new insights into the heterogeneous fine-scale cementitious hydration products associated with basaltic ash-portland cement reactions. © 2013 Published by Elsevier Ltd.

Impact of problem finding on the quality of authentic open inquiry science research projects

Science.gov (United States)

Labanca, Frank

2008-11-01

Problem finding is a creative process whereby individuals develop original ideas for study. Secondary science students who successfully participate in authentic, novel, open inquiry studies must engage in problem finding to determine viable and suitable topics. This study examined problem finding strategies employed by students who successfully completed and presented the results of their open inquiry research at the 2007 Connecticut Science Fair and the 2007 International Science and Engineering Fair. A multicase qualitative study was framed through the lenses of creativity, inquiry strategies, and situated cognition learning theory. Data were triangulated by methods (interviews, document analysis, surveys) and sources (students, teachers, mentors, fair directors, documents). The data demonstrated that the quality of student projects was directly impacted by the quality of their problem finding. Effective problem finding was a result of students using resources from previous, specialized experiences. They had a positive self-concept and a temperament for both the creative and logical perspectives of science research. Successful problem finding was derived from an idiosyncratic, nonlinear, and flexible use and understanding of inquiry. Finally, problem finding was influenced and assisted by the community of practicing scientists, with whom the students had an exceptional ability to communicate effectively. As a result, there appears to be a juxtaposition of creative and logical/analytical thought for open inquiry that may not be present in other forms of inquiry. Instructional strategies are suggested for teachers of science research students to improve the quality of problem finding for their students and their subsequent research projects.

Analysis of heavy metal contents in gray and white MTA and 2 kinds of Portland cement: a preliminary study.

Science.gov (United States)

Chang, Seok Woo; Shon, Won Jun; Lee, WooCheol; Kum, Kee Yeon; Baek, Seung Ho; Bae, Kwang Shik

2010-04-01

The levels of 10 heavy metals (arsenic, bismuth, cadmium, chromium, copper, iron, lead, manganese, nickel, and zinc) in gray Portland cement (GPC), white Portland cement (WPC), gray MTA (GMTA), and white MTA (WMTA) were analyzed by inductively coupled plasma-atomic emission spectrometry (ICP-AES). One gram of each material was digested with 80 degrees C "aqua-regia" (7 mL of 60% HNO3 and 21 mL of 35% HCl), filtered, and analyzed by ICP-AES. The analysis was performed 6 times and the data were analyzed statistically. Arsenic and lead concentrations were the highest in GPC (P cements (P Portland cement versus MTA, the differences in purity may be considered. Copyright 2010 Mosby, Inc. All rights reserved.

Evaluation of physico-chemical properties of Portland cements and MTA

Directory of Open Access Journals (Sweden)

Jorge Luis Gonçalves

2010-09-01

Full Text Available The purpose of this study was to evaluate the hydrogenionic potential and electrical conductivity of Portland cements and MTA, as well as the amount of arsenic and calcium released from these materials. In Teflon molds, samples of each material were agitated and added to plastic flasks containing distilled water for 3, 24, 72 and 168 h. The results were analyzed with a Kruskal-Wallis non-parametric test for global comparisons and a Dunn-Tukey test for pairwise comparisons. The results revealed no significant differences in the pH of the materials (p > 0.05. The electrical conductivity of the cements were not statistically different (p > 0.05. White non-structural cement and MTA BIO released the largest amount of calcium ions into solution (p 0.05. The results indicated that the physico-chemical properties of Portland cements and MTA were similar. Furthermore, all materials produced an alkaline environment and can be considered safe for clinical use because arsenic was not released. The electrical conductivity and the amount of calcium ions released into solution increased over time.

Evaluation of physico-chemical properties of Portland cements and MTA.

Science.gov (United States)

Gonçalves, Jorge Luis; Viapiana, Raqueli; Miranda, Carlos Eduardo Saraiva; Borges, Alvaro Henrique; Cruz Filho, Antônio Miranda da

2010-01-01

The purpose of this study was to evaluate the hydrogenionic potential and electrical conductivity of Portland cements and MTA, as well as the amount of arsenic and calcium released from these materials. In Teflon molds, samples of each material were agitated and added to plastic flasks containing distilled water for 3, 24, 72 and 168 h. The results were analyzed with a Kruskal-Wallis non-parametric test for global comparisons and a Dunn-Tukey test for pairwise comparisons. The results revealed no significant differences in the pH of the materials (p > 0.05). The electrical conductivity of the cements were not statistically different (p > 0.05). White non-structural cement and MTA BIO released the largest amount of calcium ions into solution (p 0.05). The results indicated that the physico-chemical properties of Portland cements and MTA were similar. Furthermore, all materials produced an alkaline environment and can be considered safe for clinical use because arsenic was not released. The electrical conductivity and the amount of calcium ions released into solution increased over time.

Experimental study of chloride diffusivity in unsaturated ordinary Portland cement mortar

NARCIS (Netherlands)

Zhang, Y.; Ye, G.; Santhanam, M.

2017-01-01

Experiments are carried out to investigate the chloride diffusivity in partially saturated ordinary Portland cement mortars with water-to-cement (w/c) ratios of 0.4, 0.5 and 0.6. Based on resistivity measurement and Nernst-Einstein equation, the chloride diffusivities of cement mortars at various

X-ray diffractometry of steam cured ordinary Portland and blast-furnace-slag cements

International Nuclear Information System (INIS)

Camarini, G.; Djanikian, J.G.

1994-01-01

This work studies some aspects of the phases produced by hydration of ordinary and blast-furnace-slag cements, at normal conditions and steam cured (60 and 95 0 C), using an X-ray diffraction technique. The blast-furnace-slag cement was a mixture of 50% of ordinary Portland cement and 50% of blast-furnace-slag (separately grinding). After curing the X-ray diffraction reveals that, in relation to ordinary Portland cement, the main phases in blast-furnace-slag cement are hydrated silicates and aluminates, hydro garnet, etringitte and mono sulphate. After steam curing the hydration of blast-furnace-slag cement proceeds. This is a result of the slag activation by the curing temperature. (author). 8 refs., 3 figs., 1 tab

Comparative Study of Portland Cement-based and Zeolite-based Concretes in Terms of Hexavalent Chromium Leaching

Directory of Open Access Journals (Sweden)

Oravec Jozef

2016-12-01

Full Text Available The paper presents the results of the leaching study of Portland cement-based and zeolite-based concretes regarding water soluble hexavalent chromium. Three leaching water media (distilled water, rain water, and Britton-Robinson buffer of various pH values were under investigation. The correlation between pH and leached-out concentrations of chromium was not confirmed. The content of hexavalent water-soluble chromium in leachates of zeolite-based concretes was found to be higher than that in leachates of Portland cement-based samples.

Portland cement concrete pavement review of QC/QA data 2000 through 2009.

Science.gov (United States)

2011-04-01

This report analyzes the Quality Control/Quality Assurance (QC/QA) data for Portland cement concrete pavement : (PCCP) awarded in the years 2000 through 2009. Analysis of the overall performance of the projects is accomplished by : reviewing the Calc...

Natural cement as the precursor of Portland cement: Methodology for its identification

International Nuclear Information System (INIS)

Varas, M.J.; Alvarez de Buergo, M.; Fort, R.

2005-01-01

When cements appeared in the 19th century, they took the place of traditional binding materials (lime, gypsum, and hydraulic lime) which had been used until that time. Early cements can be divided into two groups, natural and artificial (Portland) cements. Natural cements were introduced first, but their widespread usage was short-lived as they were quickly replaced by artificial cements (Portland), still the most important and predominant today. The main differences between natural and artificial cements arise during the manufacturing process. The final properties of the cements are greatly influenced by differences in the raw materials and burning temperatures employed. The aim of this paper is to assess the efficiency of traditional analytical techniques (petrographic microscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM), and Fourier transform infrared spectroscopy (FTIR)) used to differentiate natural and artificial cements

X-ray diffractometry of steam cured ordinary Portland and blast-furnace-slag cements; Difratometria de raios X de pastas de cimento Portland comum e de alto-forno submetidas a cura termica

Energy Technology Data Exchange (ETDEWEB)

Camarini, G [Universidade Estadual de Campinas, SP (Brazil). Faculdade de Engenharia; Djanikian, J G [Sao Paulo Univ., SP (Brazil). Escola Politecnica

1994-12-31

This work studies some aspects of the phases produced by hydration of ordinary and blast-furnace-slag cements, at normal conditions and steam cured (60 and 95{sup 0} C), using an X-ray diffraction technique. The blast-furnace-slag cement was a mixture of 50% of ordinary Portland cement and 50% of blast-furnace-slag (separately grinding). After curing the X-ray diffraction reveals that, in relation to ordinary Portland cement, the main phases in blast-furnace-slag cement are hydrated silicates and aluminates, hydro garnet, etringitte and mono sulphate. After steam curing the hydration of blast-furnace-slag cement proceeds. This is a result of the slag activation by the curing temperature. (author). 8 refs., 3 figs., 1 tab.

Recycled Portland cement concrete pavements : Part II, state-of-the art summary.

Science.gov (United States)

1979-01-01

This report constitutes a review of the literature concerning recycling of portland cement concrete pavements by crushing the old pavement and reusing the crushed material as aggregate in a number of applications. A summary of the major projects cond...

Thermal analysis of borogypsum and its effects on the physical properties of Portland cement

International Nuclear Information System (INIS)

Elbeyli, Iffet Yakar; Derun, Emek Moeroeydor; Guelen, Jale; Piskin, Sabriye

2003-01-01

Borogypsum, which consists mainly of gypsum crystals, B 2 O 3 and some impurities, is formed during the production of boric acid from colemanite, which is an important borate ore. In this study, the effect of borogypsum and calcined borogypsum on the physical properties of ordinary Portland cement (OPC) has been investigated. The calcination temperature and transformations in the structures of borogypsum and natural gypsum were determined by differential thermal analysis (DTA), thermogravimetric analysis (TGA) and X-ray diffraction (XRD) techniques. Thermal experiments were carried out between ambient temperature and 500 deg. C in an air atmosphere at a heating rate of 10 deg. C min -1 . After calculation of enthalpy and determination of conversion temperatures, borogypsum (5% and 7%), hemihydrate borogypsum (5%) and natural gypsum (5%) were added separately to Portland cement clinker and cements were ground in the laboratory. The final products were tested for chemical analysis, compressive strength, setting time, Le Chatelier expansion and fineness properties according to the European Standard (EN 196). The results show that increasing the borogypsum level in Portland cement from 5% to 7% caused an increase in setting time and a decrease in soundness expansion and compressive strength. The cement prepared with borogypsum (5%) was found to have similar strength properties to those obtained with natural gypsum, whereas a mixture containing 5% of hemihydrate borogypsum was found to develop 25% higher compressive strength than the OPC control mixtures at 28 days. For this reason, utilization of calcined borogypsum in cement applications is expected to give better results than untreated borogypsum. It is concluded that hemihydrate borogypsum could be used as a retarder for Portland cement as an industrial side. This would play an important role in reducing environmental pollution

Portland blended cements: demolition ceramic waste management

International Nuclear Information System (INIS)

Trezza, M.A.; Zito, S.; Tironi, A.; Irassar, E.F.; Rahhal, V.F.

2017-01-01

Demolition ceramic wastes (DCWs) were investigated in order to determine their potential use as supplementary cementitious materials in Portland Blended Cements (PBCs). For this purpose, three ceramic wastes were investigated. After characterization of the materials used, the effect of ceramic waste replacement (8, 24 and 40% by mass) was analyzed. Pozzolanic activity, hydration progress, workability and compressive strength were determined at 2, 7 and 28 days. The results showed that the ground wastes behave as filler at an early age, but as hydration progresses, the pozzolanic activity of ceramic waste contributes to the strength requirement. [es

76 FR 76760 - Gray Portland Cement and Cement Clinker From Japan

Science.gov (United States)

2011-12-08

... and Cement Clinker From Japan Determination On the basis of the record \\1\\ developed in the subject... duty order on gray Portland cement and cement clinker from Japan would be likely to lead to... and Cement Clinker from Japan: Investigation No. 731- TA-461 (Third Review). By order of the...

Durabilidad de un suelo contaminado y tratado con cemento portland Durability of a contaminated soil treated with portland cement

OpenAIRE

José W Jiménez Rojas; Nilo C Consoli; Karla Salvagni Heineck

2008-01-01

Este trabajo tiene por objetivo la aplicación de la técnica de solidificación/estabilización de suelos contaminados, analizando específicamente el comportamiento físico del suelo a través de ensayos de durabilidad. El suelo fue contaminado en laboratorio con residuo oleoso y la aplicación de la técnica tuvo cómo agente de encapsulamiento el cemento Portland CP V-ARI. Los ensayos de durabilidad, realizados según la NBR 13554 (1996), tuvieron como objetivo estudiar el grado de desagregación y v...

Evaluation of dynamic elasticity module in samples of Portland (type 1) cement paste exposed to neutronic irradiation

International Nuclear Information System (INIS)

Rosa Junior, A.A.; Lucki, G.

1986-01-01

The fast neutron radiation effects and temperature on Portland cement are studied. The Dynamic Elasticity Module (Ed) in samples of Portland cement paste was evaluated. Ultrassonic technics were applied (resonance frequency and pulse velocity). The samples were irradiated with fast neutrons to fluence of 7,2 x 10 18 n/cm 2 (E approx. 1 MeV), at temperature of 120 + - 5 0 C, due to gamma heating. This temperature was simulated in laboratory in a microwave oven. (Author) [pt

Portland cement hydration and early setting of cement stone intended for efficient paving materials

Science.gov (United States)

Grishina, A.

2017-10-01

Due to the growth of load on automotive roads, modern transportation engineering is in need of efficient paving materials. Runways and most advanced highways require Portland cement concretes. This makes important the studies directed to improvement of binders for such concretes. In the present work some peculiarities of the process of Portland cement hydration and early setting of cement stone with barium hydrosilicate sol were examined. It was found that the admixture of said sol leads to a shift in the induction period to later times without significant change in its duration. The admixture of a modifier with nanoscale barium hydrosilicates increases the degree of hydration of the cement clinker minerals and changes the phase composition of the hydration products; in particular, the content of portlandite and tricalcium silicate decreases, while the amount of ettringite increases. Changes in the hydration processes of Portland cement and early setting of cement stone that are caused by the nanoscale barium hydrosilicates, allow to forecast positive technological effects both at the stage of manufacturing and at the stage of operation. In particular, the formwork age can be reduced, turnover of molds can be increased, formation of secondary ettringite and corrosion of the first type can be eliminated.

Mineral Trioxide Aggregate and Portland Cement for Direct Pulp Capping in Dog: A Histopathological Evaluation

Directory of Open Access Journals (Sweden)

Maryam Bidar

2014-09-01

Full Text Available Background and aims. Mineral trioxide aggregate and calcium hydroxide are considered the gold standard pulp-capping materials. Recently, Portland cement has been introduced with properties similar to those of mineral trioxide aggregate. His-topathological effects of direct pulp capping using mineral trioxide aggregate and Portland cements on dog dental pulp tis-sue were evaluated in the present study. Materials and methods. This histopatological study was carried out on 64 dog premolars. First, the pulp was exposedwith a sterile bur. Then, the exposed pulp was capped with white or gray mineral trioxide aggregates and white or gray Port-land cements in each quadrant and sealed with glass-ionomer. The specimens were evaluated under a light microscope after 6 months. Statistical analysis was carried out using Kruskal-Wallis test. Statistical significance was defined at α=5%. Results. There was no acute inflammation in any of the specimens. Chronic inflammation in white and gray mineral triox-ide aggregates and white and gray Portland cements was reported to be 45.5%, 27.3%, 57.1% and 34.1%, respectively. Al-though the differences were not statistically significant, severe inflammation was observed mostly adjacent to white mineral trioxide aggregate. The largest extent of increased vascularization (45% and the least increase in fibrous tissue were ob-served adjacent to white mineral trioxide aggregate, with no significant differences. In addition, the least calcified tissue formed adjacent to white mineral trioxide aggregate, although the difference was not significant. Conclusion. The materials used in this study were equally effective as pulp protection materials following direct pulp cap-ping in dog teeth.

Predicting the durability of Portland cement systems in aggressive environments--Laboratory validation

International Nuclear Information System (INIS)

Maltais, Y.; Samson, E.; Marchand, J.

2004-01-01

Portland cement systems are often exposed to severe environments, and their long-term performance is of concern. The main results of a comprehensive investigation of deterioration processes that may affect the behavior of Portland cement systems exposed to chemically aggressive environments is presented. As part of this investigation, well-cured cement paste discs were fully characterized and exposed to deionized water and sodium sulfate solutions. Degradation experiments were conducted under saturated and unsaturated conditions. At the end of the exposure period, microstructural alterations were investigated by microprobe analyses, scanning electron microscope observations and energy-dispersive X-ray analyses. Test results provide information on the basic aspects of various degradation phenomena, such as decalcification and external sulfate attack. Experimental results were also compared with results obtained by a numerical model. The analysis reveals that the intricate microstructural features of the degraded samples could be accurately reproduced by the model

Planetary Science Technology Infusion Study: Findings and Recommendations Status

Science.gov (United States)

Anderson, David J.; Sandifer, Carl E., II; Sarver-Verhey, Timothy R.; Vento, Daniel M.; Zakrajsek, June F.

2014-01-01

The Planetary Science Division (PSD) within the National Aeronautics and Space Administrations (NASA) Science Mission Directorate (SMD) at NASA Headquarters sought to understand how to better realize a scientific return on spacecraft system technology investments currently being funded. In order to achieve this objective, a team at NASA Glenn Research Center was tasked with surveying the science and mission communities to collect their insight on technology infusion and additionally sought inputs from industry, universities, and other organizations involved with proposing for future PSD missions. This survey was undertaken by issuing a Request for Information (RFI) activity that requested input from the proposing community on present technology infusion efforts. The Technology Infusion Study was initiated in March 2013 with the release of the RFI request. The evaluation team compiled and assessed this input in order to provide PSD with recommendations on how to effectively infuse new spacecraft systems technologies that it develops into future competed missions enabling increased scientific discoveries, lower mission cost, or both. This team is comprised of personnel from the Radioisotope Power Systems (RPS) Program and the In-Space Propulsion Technology (ISPT) Program staff.The RFI survey covered two aspects of technology infusion: 1) General Insight, including: their assessment of barriers to technology infusion as related to infusion approach; technology readiness; information and documentation products; communication; integration considerations; interaction with technology development areas; cost-capped mission areas; risk considerations; system level impacts and implementation; and mission pull. 2) Specific technologies from the most recent PSD Announcements of Opportunities (AOs): The Advanced Stirling Radioisotope Generator (ASRG), aerocapture and aeroshell hardware technologies, the NASA Evolutionary Xenon Thruster (NEXT) ion propulsion system, and the

NESHAP for the Portland Cement Manufacturing Industry: Fact Sheets for Actions Since 2015

Science.gov (United States)

EPA is extending its approval for the use of an alternative method to show compliance with hydrogen chloride (HCl) emissions limits in the National Emission Standards for Hazardous Air Pollutants for the Portland Cement Manufacturing Industry

Healing of apical rarefaction of three nonvital open apex anterior teeth using a white portland cement apical plug

Directory of Open Access Journals (Sweden)

Amitabha Chakraborty

2012-01-01

Full Text Available The major challenge of performing root canal treatment in an open apex pulp-less tooth is to obtain a good apical seal. MTA has been successfully used to achieve a good apical seal, wherein the root canal obturation can be done immediately. MTA and White Portland Cement has been shown similarity in their physical, chemical and biological properties and has also shown similar outcome when used in animal studies and human trials. In our study, open apex of three non vital upper central incisors has been plugged using modified white Portland cement. 3 to 6 months follow up revealed absence of clinical symptoms and disappearance of peri-apical rarefactions. The positive clinical outcome may encourage the future use of white Portland cement as an apical plug material in case of non vital open apex tooth as much cheaper substitute of MTA.

Elemental atmospheric pollution assessment via moss-based measurements in Portland, Oregon

Science.gov (United States)

Demetrios Gatziolis; Sarah Jovan; Geoffrey Donovan; Michael Amacher; Vicente Monleon

2016-01-01

Mosses accumulate pollutants from the atmosphere and can serve as an inexpensive screening tool for mapping air quality and guiding the placement of monitoring instruments. We measured 22 elements using 346 moss samples collected across Portland, Oregon, in December 2013. Our objectives were to develop citywide maps showing concentrations of each element in moss and...

Trees in the city: valuing street trees in Portland, Oregon

Science.gov (United States)

G.H. Donovan; D.T. Butry

2010-01-01

We use a hedonic price model to simultaneously estimate the effects of street trees on the sales price and the time-on-market (TOM) of houses in Portland. Oregon. On average, street trees add $8,870 to sales price and reduce TOM by 1.7 days. In addition, we found that the benefits of street trees spill over to neighboring houses. Because the provision and maintenance...

Effects of chemical and mineral additives and the water/cement ratio on the thermal resistance of Portland cement concrete

International Nuclear Information System (INIS)

Cesar, Leandro Cesar Dias; Morelli, Arnaldo C.; Baldo, Joao Baptista

1998-01-01

The exposure of Portland concrete to high temperatures (>250 deg C) can damage drastically the microstructural integrity of the material. Since the water/cement ratio as well as the inclusion of superplasticizers and mineral additives (silica fume) can alter constitutively and micro structurally the material, in this work it was investigated per effect of these additions on the damage resistance of portland concrete after exposure to high temperatures. (author)

Recycling of porcelain tile polishing residue in portland cement: hydration efficiency.

Science.gov (United States)

Pelisser, Fernando; Steiner, Luiz Renato; Bernardin, Adriano Michael

2012-02-21

Ceramic tiles are widely used by the construction industry, and the manufacturing process of ceramic tiles generates as a major residue mud derived from the polishing step. This residue is too impure to be reused in the ceramic process and is usually discarded as waste in landfills. But the analysis of the particle size and concentration of silica of this residue shows a potential use in the manufacture of building materials based on portland cement. Tests were conducted on cement pastes and mortars using the addition of 10% and 20% (mass) of the residue. The results of compressive strength in mortars made up to 56 days showed a significant increase in compressive strength greater than 50%. The result of thermogravimetry shows that portlandite is consumed by the cement formed by the silica present in the residue in order to form calcium silicate hydrate and featuring a pozzolanic reaction. This effect improves the performance of cement, contributes to research and application of supplementary cementitious materials, and optimizes the use of portland cement, reducing the environmental impacts of carbon dioxide emissions from its production.

Performance Characteristics of Waste Glass Powder Substituting Portland Cement in Mortar Mixtures

Science.gov (United States)

Kara, P.; Csetényi, L. J.; Borosnyói, A.

2016-04-01

In the present work, soda-lime glass cullet (flint, amber, green) and special glass cullet (soda-alkaline earth-silicate glass coming from low pressure mercury-discharge lamp cullet and incandescent light bulb borosilicate glass waste cullet) were ground into fine powders in a laboratory planetary ball mill for 30 minutes. CEM I 42.5N Portland cement was applied in mortar mixtures, substituted with waste glass powder at levels of 20% and 30%. Characterisation and testing of waste glass powders included fineness by laser diffraction particle size analysis, specific surface area by nitrogen adsorption technique, particle density by pycnometry and chemical analysis by X-ray fluorescence spectrophotometry. Compressive strength, early age shrinkage cracking and drying shrinkage tests, heat of hydration of mortars, temperature of hydration, X-ray diffraction analysis and volume stability tests were performed to observe the influence of waste glass powder substitution for Portland cement on physical and engineering properties of mortar mixtures.

D90: The Strongest Contributor to Setting Time in Mineral Trioxide Aggregate and Portland Cement.

Science.gov (United States)

Ha, William N; Bentz, Dale P; Kahler, Bill; Walsh, Laurence J

2015-07-01

The setting times of commercial mineral trioxide aggregate (MTA) and Portland cements vary. It was hypothesized that much of this variation was caused by differences in particle size distribution. Two gram samples from 11 MTA-type cements were analyzed by laser diffraction to determine their particle size distributions characterized by their percentile equivalent diameters (the 10th percentile, the median, and the 90th percentile [d90], respectively). Setting time data were received from manufacturers who performed indentation setting time tests as specified by the standards relevant to dentistry, ISO 6786 (9 respondents) or ISO 9917.1 (1 respondent), or not divulged to the authors (1 respondent). In a parallel experiment, 6 samples of different size graded Portland cements were produced using the same cement clinker. The measurement of setting time for Portland cement pastes was performed using American Society for Testing and Materials C 191. Cumulative heat release was measured using isothermal calorimetry to assess the reactions occurring during the setting of these pastes. In all experiments, linear correlations were assessed between setting times, heat release, and the 3 particle size parameters. Particle size varied considerably among MTA cements. For MTA cements, d90 was the particle size characteristic showing the highest positive linear correlation with setting time (r = 0.538). For Portland cement, d90 gave an even higher linear correlation for the initial setting time (r = 0.804) and the final setting time (r = 0.873) and exhibited a strong negative linear correlation for cumulative heat release (r = 0.901). Smaller particle sizes result in faster setting times, with d90 (the largest particles) being most closely correlated with the setting times of the samples. Copyright © 2015 American Association of Endodontists. All rights reserved.

Portland cement for SO.sub.2 control in coal-fired power plants

Science.gov (United States)

Steinberg, Meyer

1985-01-01

There is described a method of removing oxides of sulfur from the emissions of fossil fuel combustion by injecting portland cement into the boiler with the fuel, the combustion air, or downstream with the combustion gases. There is also described the cement products that result from this method.

Portland cement for SO/sub 2/ control in coal-fired power plants

Science.gov (United States)

Steinberg, M.

1984-10-17

A method is described for removing oxides of sulfur from the emissions of fossil fuel combustion by injecting portland cement into the boiler with the fuel, the combustion air, or downstream with the combustion gases. The cement products that result from this method is also described. 1 tab.

76 FR 33763 - Findings of Misconduct in Science/Research Misconduct

Science.gov (United States)

2011-06-09

..., Ph.D., St. Jude Children's Research Hospital: Based on the findings of an investigation report by St... oversight review, ORI found that Philippe Bois, Ph.D., former postdoctoral fellow, Department of Biochemistry, St. Jude, engaged in misconduct in science and research misconduct in research funded by National...

Influence Of Cement Kiln Dust As Partial Replacement On Some Properties Of Ordinary And White Portland Cement

Directory of Open Access Journals (Sweden)

Salah Sharif

2013-04-01

Full Text Available Cement Kiln Dust (CKD is produced as a solid waste with large quantities during manufacturing of Portland cement clinker. The possibility of utilizing CKD as partial replacement for Ordinary Portland Cement (OPC and White Portland Cement (WPC produced in factories of the Iraqi cement state company has been examined in this study to fulfil the environmental and economical aims. Different percentages of CKD were blended with OPC and WPC mixes. The results show that the amount of water for normal consistency were increased with about 39 % and 31 % for OPC and WPC blended with 25 % CKD. The setting time (initial and final decreases with increasing percent of CKD added. Compressive strength decreases slightly with increasing CKD content up to 10 %. For 7- day curing time, it decreases 7 % and 9 % for OPC and WPC mixes, respectively. As percent of added CKD increases to more than 10 %, the compressive strength and other parameters where affected significantly. Overall results proved that OPC and WPC blended with up to 10 % CKD are admissible for passing relevant specification requirements.

Physicochemical and mechanical properties of zirconium oxide and niobium oxide modified Portland cement-based experimental endodontic sealers.

Science.gov (United States)

Viapiana, R; Flumignan, D L; Guerreiro-Tanomaru, J M; Camilleri, J; Tanomaru-Filho, M

2014-05-01

To evaluate the physicochemical and mechanical properties of Portland cement-based experimental sealers (ES) with different radiopacifying agents (zirconium oxide and niobium oxide micro- and nanoparticles) in comparison with the following conventional sealers: AH Plus, MTA Fillapex and Sealapex. The materials were tested for setting time, compressive strength, flow, film thickness, radiopacity, solubility, dimensional stability and formaldehyde release. Data were subjected to anova and Tukey tests (P 0.05) and lower solubility when compared with MTA Fillapex and Sealapex (P Portland cement-based experimental endodontic sealers presented physicochemical properties according to the specifications no 57 ANSI/ADA (ADA Professional Product Review, 2008) and ISO 6876 (Dentistry - Root Canal Sealing Materials, 2012, British Standards Institution, London, UK). The sealers had setting times and flow ability that was adequate for clinical use, satisfactory compressive strength and low solubility. Additional studies should be carried out with the purpose of decreasing the film thickness and to determine the ideal ratio of radiopacifying agents in Portland cement-based root canal sealers. © 2013 International Endodontic Journal. Published by John Wiley & Sons Ltd.

Hydration kinetics for the alite, belite, and calcium aluminate phase in Portland cements from 27Al and 29Si MAS NMR spectroscopy

DEFF Research Database (Denmark)

Skibsted, Jørgen; Jensen, Ole Mejlhede; Jakobsen, Hans Jørgen

1997-01-01

29Si magic-angle spinning (MAS) NMR spectroscopy is shown to be a valuable tool for obtaining the quantities of alite and belite in hydrated Portland cements. The hydration (1-180 days) of a white Portland cement with 10 wt.% silica fume added is investigated and the degrees of hydration for alite...

The biomineralization ability of mineral trioxide aggregate and Portland cement on dentin enhances the push-out strength.

Science.gov (United States)

Reyes-Carmona, Jessie F; Felippe, Mara S; Felippe, Wilson T

2010-02-01

Recently, it was shown that the interaction of each of mineral trioxide aggregate (MTA) and Portland cement with dentin in phosphate-buffered saline (PBS) promotes a biomineralization process that leads to the formation of an interfacial layer with tag-like structures at the cement-dentin interface. This study analyzes the influence of the biomineralization process on the push-out strength of ProRoot MTA (Dentsply Tulsa Dental, Tulsa, OK), MTA Branco (Angelus Soluções Odontológicas, Londrina, PR, Brazil), MTA BIO (Angelus Soluções Odontológicas), or Portland cement with and without calcium chloride. Dentin discs with standardized cavities were filled with ProRoot MTA, MTA Branco, MTA BIO, white Portland cement + 20% bismuth oxide (PC1), or PC1 + 10% of calcium chloride (PC2). The specimens were randomly divided into two groups: cement in contact with a wet cotton pellet for 72 hours or immersed in PBS for 2 months. The bond strengths were measured with the Instron Testing machine (Model 4444; Instron Corp, Canton, MA), and the fractured surfaces on the root walls were observed by scanning electron microscopy. All samples immersed in PBS displayed a significantly greater resistance to displacement than that observed for the samples in contact with a wet cotton pellet for 72 hours (p Portland cements. It was concluded that the biomineralization process positively influenced the push-out bond strength of the cements, particularly the MTA groups. Copyright 2010 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Experimental investigation of the multiple scatter peak of gamma rays in portland cement in the energy range 279-1332 keV

International Nuclear Information System (INIS)

Singh, Tejbir; Singh, Parjit S

2011-01-01

The pulse height spectra for different thicknesses of portland cement in the reflected geometry has been recorded with the help of a NaI(Tl) scintillator detector and 2 K MCA card using different gamma-ray sources such as Hg 203 (279 keV), Cs 137 (662 keV) and Co 60 (1173 and 1332 keV). It has been observed that the multiple scatter peak for portland cement appears at 110 (±7) keV in all the spectra irrespective of different incident photon energies in the range 279-1332 keV from different gamma-ray sources. Further, the variation in the intensity of the multiple scatter peak with the thickness of portland cement in the backward semi-cylinders has been investigated.

XRF analysis of portland cement for major and trace elements

International Nuclear Information System (INIS)

Abdunnabi, A. R.

2012-12-01

Libyan portland cement produced in several factories around the country, in Lip tis, Zoltan, Souq-Elkamis, Dernah and El-Fatach, were analyzed for quantitative major and trace elements and mineral content, which were compered with those imported from Spain, Romania, Cyprus, and Egypt. X-ray fluorescence spectro X lab 2000 spectrometer equipped with Rh-and X-ray tube was used for the analysis of various samples. The detector Si(Li) with a resolution of 148 eV at Mn K-a=5.9 keV facilitates the determination of a wide range of elements from sodium to uranium, with a detection limit at sub levels. Cement samples in the powder form were analyzed using the pellet-technique. The pellets were prepared by mixing 4g of the cement powder with 0.9 g of binder (HWC) and pressed at high pressure. A ful analysis including, background counting, matrix correction and all relevant corrections were achieved automatically by XLAB 2000 software package. For major and trace elements X RF results were higher for most of the elements than those analyzed with atomic absorption spectrometry. The mineral content showed that Libyan cement is comparable to the imported ones, also the Libyan cement meets the requirements of the international specifications of the portland cement. (Author)

A Histologic Evaluation on Tissue Reaction to Three Implanted Materials (MTA, Root MTA and Portland Cement Type I in the Mandible of Cats

Directory of Open Access Journals (Sweden)

F. Sasani

2004-09-01

Full Text Available Statement of Problem: Nowadays Mineral Trioxide aggregate (MTA is widely used for root end fillings, pulp capping, perforation repair and other endodontic treatments.Investigations have shown similar physical and chemical properties for Portland cement and Root MTA with those described for MTA.Purpose: The aim of this in vitro study was to evaluate the tissue reaction to implanted MTA, Portland cement and Root MTA in the mandible of cats.Materials and Methods: Under asepsis condition and general anesthesia, a mucoperiosteal flap, following the application of local anesthesia, was elevated to expose mandibular symphysis. Two small holes in both sides of mandible were drilled. MTA, Portland cement and Root MTA were mixed according to the manufacturers, recommendation and placed in bony cavities. In positive control group, the test material was Zinc oxide powder plus tricresoformalin. In negative control group, the bony cavities were left untreated. After 3,6 and 12 weeks, the animals were sacrificed and the mandibular sections were prepared for histologic examination under light microscope. The presence and thickness of inflammation, presence of fibrosis capsule, the severity of fibrosis and bone formation were investigated. The data were submitted to Exact Fisher test, chi square test and Kruskal-Wallis test for statistical analysis.Results: No statistically significant differences were found in the degree of inflammation,presence of fibrotic capsule, severity of fibrosis and inflammation thickness between Root MTA, Portland cement and MTA (P>0.05. There was no statistical difference in boneformation between MTA and Portland cement (P>0.05. However, bone formation was not found in any of the Root MTA specimens and the observed tissue was exclusively of fibrosis type.Conclusion: The physical and histological results observed with MTA are similar to those of Root MTA and Portland cement. Additionally, all of these three materials are biocompatible

Determination of coefficient of thermal expansion for Portland Cement Concrete pavements for MEPDG Implementation

Science.gov (United States)

2012-10-01

The Coefficient of Thermal Expansion (CTE) is an important parameter in Portland Cement Concrete (PCC) pavement analysis and design as it is directly proportional to the magnitude of temperature-related pavement deformations throughout the pavement s...

2014 Oregon Department of Geology and Mineral Industries (DOGAMI) Oregon Lidar: Metro Portland, OR

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The dataset encompasses 1221.6 square miles in portions of the greater Portland Metro area in the state of Oregon. The highest hit digital surface models (DSM)...

The influence of shrinkage-cracking on the drying behaviour of White Portland cement using Single-Point Imaging (SPI).

Science.gov (United States)

Beyea, S D; Balcom, B J; Bremner, T W; Prado, P J; Cross, A R; Armstrong, R L; Grattan-Bellew, P E

1998-11-01

The removal of water from pores in hardened cement paste smaller than 50 nm results in cracking of the cement matrix due to the tensile stresses induced by drying shrinkage. Cracks in the matrix fundamentally alter the permeability of the material, and therefore directly affect the drying behaviour. Using Single-Point Imaging (SPI), we obtain one-dimensional moisture profiles of hydrated White Portland cement cylinders as a function of drying time. The drying behaviour of White Portland cement, is distinctly different from the drying behaviour of related concrete materials containing aggregates.

Study irradiation damage by fast neutrons in Portland cement by means of ultra-sound

International Nuclear Information System (INIS)

Rosa Junior, A.A.

1988-01-01

The effect of neutron irradiation in samples of Portland cement paste was evaluated, using the resonance frequency method and pulse velocity of ultra-sound technique. The samples were divide in three groups: 1) Monitoring samples; 2) Samples to gamma heating simulation; 3) Fast neutron irradiated samples in reactor core. Santa Rita Portland cement was utilized for samples preparation with water-cement rate of 0,40 l/kg. The irradiation was performed in the research reactor IEA-R1, at IPEN-CNEN/SP, with an integrated flux of 7,2 X 10 sup(18) n/cm sup(2) (E approx. 1 Mev). The samples of group 2 were submitted to special micro-waves heat treatment-with the same number of cycles of the reactor-which allowed the detection of fast neutron radiation effects within the predominant thermal effects. (author)

Ordinary Portland Cement matrix for solidification of cellulosic protective clothes hazardous wastes

International Nuclear Information System (INIS)

Shatta, H.A.; Saleh, H.M.

2006-01-01

The used cellulosic protective clothes constitutes considerable fraction of the hazardous and radioactive wastes accumulated during the practical daily life. The direct solidification of these wastes with ordinary Portland cement resulted in waste forms having undesired characters, therefore, it is recommended to immobilize the secondary waste solutions coming from the oxidative degradation of the used protective clothes waste simulates rather than direct imbedding. IR analyses, X-ray diffraction and thermal characteristics for products of both direct encapsulation of the waste and the cementation of its degradation products were performed to evaluate the properties of the final waste cemented form before their disposal. Based on the results reached from X-ray diffraction, IR spectrograms and thermal analyses reports, it could be stated that no detectable changes in hydration and curing coarse of ordinary Portland cement when mixing the residual secondary waste solution resulting from the oxidative degradation of the used protective clothes waste simulate compared with mixing cement with water and in reverse with imbedding the unprocessed waste in cement matrix

Bioactive coatings on Portland cement substrates: Surface precipitation of apatite-like crystals

International Nuclear Information System (INIS)

Gallego, Daniel; Higuita, Natalia; Garcia, Felipe; Ferrell, Nicholas; Hansford, Derek J.

2008-01-01

We report a method for depositing bioactive coatings onto cement materials for bone tissue engineering applications. White Portland cement substrates were hydrated under a 20% CO 2 atmosphere, allowing the formation of CaCO 3 . The substrates were incubated in a calcium phosphate solution for 1, 3, and 6 days (CPI, CPII, and CPIII respectively) at 37 deg. C to induce the formation of carbonated apatite. Cement controls were prepared and hydrated with and without CO 2 atmosphere (C+ and C- respectively). The presence of apatite-like crystals was verified by Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy (EDS). The substrate cytocompatibility was evaluated via SEM after 24 hour cell cultures. SEM revealed the presence Ca(OH) 2 on C-, and CaCO 3 on C+. Apatite-like crystals were detected only on CPIII, confirmed by phosphorus EDS peaks only for CPIII. Cells attached and proliferated similarly well on all the substrates except C-. These results prove the feasibility of obtaining biocompatible and bioactive coatings on Portland cement for bone tissue engineering applications

Portland cement with additives in the repair of furcation perforations in dogs.

Science.gov (United States)

Silva Neto, José Dias da; Schnaider, Taylor Brandão; Gragnani, Alfredo; Paiva, Anderson Paulo de; Novo, Neil Ferreira; Ferreira, Lydia Masako

2012-11-01

To evaluate the use of Portland cements with additives as furcation perforation repair materials and assess their biocompatibility. The four maxillary and mandibular premolars of ten male mongrel dogs (1-1.5 years old, weighing 10-15 kg) received endodontic treatment (n=80 teeth). The furcations were perforated with a round diamond bur (1016 HL). The perforations involved the dentin, cementum, periodontal ligament, and alveolar bone. A calcium sulfate barrier was placed into the perforated bone to prevent extrusion of obturation material into the periradicular space. The obturation materials MTA (control), white, Type II, and Type V Portland cements were randomly allocated to the teeth. Treated teeth were restored with composite resin. After 120 days, the animals were sacrificed and samples containing the teeth were collected and prepared for histological analysis. There were no significant differences in the amount of newly formed bone between teeth treated with the different obturation materials (p=0.879). Biomineralization occurred for all obturation materials tested, suggesting that these materials have similar biocompatibility.

Effect of radiopaque Portland cement on mineralization in human dental pulp cells.

Science.gov (United States)

Min, Kyung-San; Lee, Sang-Im; Lee, Yoon; Kim, Eun-Cheol

2009-10-01

The aim of this study was to investigate whether radiopaque Portland cement (RPC) facilitates the mineralization process in human dental pulp cells (HDPCs) compared with pure Portland cement (PC). Under a scanning electron microscope (SEM), cellular morphology was evaluated. Alkaline phosphatase (ALP) activity was analyzed, and nodule formation was assessed by performing Alizarin Red S staining. In addition, the mRNA expressions of mineralization-related proteins were evaluated by performing a real-time polymerase chain reaction. On SEM evaluation, healthy HDPCs were found adhering to the surfaces of PC and RPC. The ALP activity increased in the PC and RPC groups compared with the control group at 1 day. Alizarin Red stain increased in the PC and RPC groups compared with the control group at 2 and 3 weeks. The mRNA expression of dentin sialophosphoprotein increased at 14 days in the PC and RPC groups. These results show that PC and RPC have similar effects in terms of mineralization and suggest that RPC also has the potential to be used as a clinically suitable pulp-capping material.

Characterization of floodflows along the Arkansas River without regulation by Pueblo Reservoir, Portland to John Martin Reservoir, Southeastern Colorado

Science.gov (United States)

Little, John R.; Bauer, Daniel P.

1981-01-01

The need for a method for estimating flow characteristics of flood hydrographs between Portland, Colo., and John Martin Reservoir has been promoted with the construction of the Pueble Reservoir. To meet this need a procedure was developed for predicting floodflow peaks, traveltimes, and volumes at any point along the Arkansas River between Portland and John Martin Reservoir without considering the existing Pueble Reservoir detention effects. A streamflow-routing model was calibrated initially and then typical flood simulations were made for the 164.8-mile study reach. Simulations were completed for varying magnitudes of floods and antecedent streamflow conditions. Multiple regression techniques were then used with simulation results as input to provide predictive relationships for food peak, volume, and traveltime. Management practices that may be used to benefit water users in the area include providing methods for the distribution and allotment of the flood waters upstream of Portland to different downstream water users according to Colorado water law and also under the Arkansas River Compact. (USGS)

Description of the structural evolution of a hydrating portland cement paste by SANS

International Nuclear Information System (INIS)

Haeussler, F.; Eichhorn, F.; Baumbach, H.

1994-01-01

On the spectrometer MURN at the pulsed reactor IBR-2 dry Portland cement, silica fume, and a hydrating Portland cement paste were studied by small-angle neutron scattering (SANS). By using the TOF-method a momentum transfer from 0.07 nm -1 to 7 nm -1 is detectable. Every component (dry cement powder, clinker minerals, hydrating cement pastes) shows a different scattering behaviour. In the measured Q-region the hardening cement paste does not show a Porod-like behaviour of SANS-curves. In contrast the Porod's potential law holds for dry powder samples of clinker minerals and silica fume. In experiments carried out to observe the hydration progress within the first 321 days the characteristics of the scattering curves (potential behaviour, the radius of gyration, and the macroscopic scattering cross section at Q = 0 nm -1 were measured. Some evolution of the inner structure of the hardened cement paste was noted. (orig.)

Effect of blastfurnace slag addition to Portland cement for cationic exchange resins encapsulation

Directory of Open Access Journals (Sweden)

Stefan L.

2013-07-01

Full Text Available In the nuclear industry, cement-based materials are extensively used to encapsulate spent ion exchange resins (IERs before their final disposal in a repository. It is well known that the cement has to be carefully selected to prevent any deleterious expansion of the solidified waste form, but the reasons for this possible expansion are not clearly established. This work aims at filling the gap. The swelling pressure of IERs is first investigated as a function of ions exchange and ionic strength. It is shown that pressures of a few tenths of MPa can be produced by decreases in the ionic strength of the bulk solution, or by ion exchanges (2Na+ instead of Ca2+, Na+ instead of K+. Then, the chemical evolution of cationic resins initially in the Na+ form is characterized in CEM I (Portland cement and CEM III (Portland cement + blastfurnace slag cements at early age and an explanation is proposed for the better stability of CEM III material.

Effect of addition of Sikament-R superplasticizer on the hydration characteristics of portland cement pastes

Directory of Open Access Journals (Sweden)

Safaa.M. El Gamal

2012-08-01

Full Text Available The effect of addition of Sikament-R superplasticizer (modified lignosulphonate base on the hydration characteristics of hardened Portland cement pastes were studied at different curing conditions. Four mixtures were prepared using 0, 0.2, 0.4 and 0.6 wt% addition of Sikament-R superplasticizer (SR of cement. These pastes were hydrated under two different conditions; (i normal curing at room temperature; 25 °C up to 90 days periods and (ii hydrothermal curing at a pressure of 8 atm. of saturated steam up to 24 h. The compressive strength, combined water content, free lime content, gel/space ratio and microstructure of hardened cement pastes were studied. The results revealed that addition of SR superplasticizer promote the dispersion of cement particles and interacts with Ca(OH2. The addition of SR superplasticizer exhibits Portland cement better workability during the preparation of pastes. In addition, amore compact structure were obtained leading to higher values of compressive strength for all the hardened hydrated pastes under both normal and hydrothermal curing. The results indicated that the addition of SR superplasticizer to Portland cement does not alter the types of hydration products formed during normal or hydrothermal conditions; only it caused a decrease in the degree of the porosity of the formed pastes.

Possibility of using waste tire rubber and fly ash with Portland cement as construction materials.

Science.gov (United States)

Yilmaz, Arin; Degirmenci, Nurhayat

2009-05-01

The growing amount of waste rubber produced from used tires has resulted in an environmental problem. Recycling waste tires has been widely studied for the last 20 years in applications such as asphalt pavement, waterproofing systems and membrane liners. The aim of this study is to evaluate the feasibility of utilizing fly ash and rubber waste with Portland cement as a composite material for masonry applications. Class C fly ash and waste automobile tires in three different sizes were used with Portland cement. Compressive and flexural strength, dry unit weight and water absorption tests were performed on the composite specimens containing waste tire rubber. The compressive strength decreased by increasing the rubber content while increased by increasing the fly ash content for all curing periods. This trend is slightly influenced by particle size. For flexural strength, the specimens with waste tire rubber showed higher values than the control mix probably due to the effect of rubber fibers. The dry unit weight of all specimens decreased with increasing rubber content, which can be explained by the low specific gravity of rubber particles. Water absorption decreased slightly with the increase in rubber particles size. These composite materials containing 10% Portland cement, 70% and 60% fly ash and 20% and 30% tire rubber particles have sufficient strength for masonry applications.

Characterization and chemical activity of Portland cement and two experimental cements with potential for use in dentistry.

Science.gov (United States)

Camilleri, J

2008-09-01

To evaluate the chemical activity of Portland cement and two other cement types with similar chemical composition to mineral trioxide aggregate with the aim of developing these cements for further applications in dentistry. The chemical composition of the three cement types namely Portland cement, calcium sulpho-aluminate cement and calcium fluoro-aluminate cement was evaluated by elemental analysis using energy dispersive analysis with X-ray under the scanning electron microscope and by X-ray diffraction analysis (XRD) to determine the phases. The constituents of the hydration reaction by-products were evaluated by XRD analysis of the set cements at 1, 7, 28 and 56 days and by analysis of the leachate by ion chromatography. The pH of both cements and leachate was determined at different time intervals. Cements admixed with micro-silica were also tested to determine the effect of micro-silica on the reaction by-products. All three cement types were composed of tricalcium silicate as the main constituent phase. The hydration reaction of Portland cement produced calcium hydroxide. However, this was not present in the other cements tested at all ages. Admixed micro-silica had little or no effect on the cements with regard to reaction by-products. The pH of all cements tested was alkaline. Both the experimental calcium sulpho-aluminate cement and calcium fluoro-aluminate cement had different hydration reactions to that of Portland cement even though calcium silicate was the major constituent element of both cement types. No calcium hydroxide was produced as a by-product to cement hydration. Micro-silica addition to the cement had no effect on the hydration reaction.

Development of Mix Design Method in Efforts to Increase Concrete Performance Using Portland Pozzolana Cement (PPC)

Science.gov (United States)

Krisnamurti; Soehardjono, A.; Zacoeb, A.; Wibowo, A.

2018-01-01

Earthquake disaster can cause infrastructure damage. Prevention of human casualties from disasters should do. Prevention efforts can do through improving the mechanical performance of building materials. To achieve high-performance concrete (HPC), usually used Ordinary Portland Cement (OPC). However, the most widely circulating cement types today are Portland Pozzolana Cement (PPC) or Portland Composite Cement (PCC). Therefore, the proportion of materials used in the HPC mix design needs to adjust to achieve the expected performance. This study aims to develop a concrete mix design method using PPC to fulfil the criteria of HPC. The study refers to the code/regulation of concrete mixtures that use OPC based on the results of laboratory testing. This research uses PPC material, gravel from Malang area, Lumajang sand, water, silica fume and superplasticizer of a polycarboxylate copolymer. The analyzed information includes the investigation results of aggregate properties, concrete mixed composition, water-binder ratio variation, specimen dimension, compressive strength and elasticity modulus of the specimen. The test results show that the concrete compressive strength achieves value between 25 MPa to 55 MPa. The mix design method that has developed can simplify the process of concrete mix design using PPC to achieve the certain desired performance of concrete.

Clinical and computed tomographic evaluation of portland cement pulpotomy in primary molar: A case report

Directory of Open Access Journals (Sweden)

Kamrun Nahar

2016-08-01

Full Text Available The present case describes the clinical & radiographic outcome of a Portland Cement pulpotomy. The 5 years old girl presenting extensive carious exposure in her mandibular left 2nd deciduous molar and was suffering pain in her left lower jaw only on exposure to cold for last 2 days. She was ultimately diagnosed clinic-radio-graphically as a case of irreversible pulpitis. Coronal pulpotomy procedure was carried out in the responsible tooth and Portland cement (PC was applied as a medicament after pulpotomy. At the 3 & 6-months follow-up appointments, treated tooth was asymptomatic clinically and radiographic examinations revealed no sign of periradicular pathosis in the pulpotomized teeth. Additionally, the formation of a dentin bridge immediately below the PC in the treated tooth was confirmed by RVG and CBCT.

Information literacy in science writing: how students find, identify, and use scientific literature

Science.gov (United States)

Klucevsek, Kristin M.; Brungard, Allison B.

2016-11-01

For undergraduate students to achieve science literacy, they must first develop information literacy skils. These skills align with Information Literacy Standards and include determining appropriate databases, distinguishing among resource types, and citing resources ethically. To effectively improve information literacy and science literacy, we must identify how students interact with authentic scientific texts. In this case study, we addressed this aim by embedding a science librarian into a science writing course, where students wrote a literature review on a research topic of their choice. Library instruction was further integrated through the use of an online guide and outside assistance. To evaluate the evolution of information literacy in our students and provide evidence of student practices, we used task-scaffolded writing assessments, a reflection, and surveys. We found that students improved their ability and confidence in finding research articles using discipline-specific databases as well as their ability to distinguish primary from secondary research articles. We also identified ways students improperly used and cited resources in their writing assignments. While our results reveal a better understanding of how students find and approach scientific research articles, additional research is needed to develop effective strategies to improve long-term information literacy in the sciences.

Problems with traditional science publishing and finding a wider niche for post-publication peer review.

Science.gov (United States)

Teixeira da Silva, Jaime A; Dobránszki, Judit

2015-01-01

Science affects multiple basic sectors of society. Therefore, the findings made in science impact what takes place at a commercial level. More specifically, errors in the literature, incorrect findings, fraudulent data, poorly written scientific reports, or studies that cannot be reproduced not only serve as a burden on tax-payers' money, but they also serve to diminish public trust in science and its findings. Therefore, there is every need to fortify the validity of data that exists in the science literature, not only to build trust among peers, and to sustain that trust, but to reestablish trust in the public and private academic sectors that are witnessing a veritable battle-ground in the world of science publishing, in some ways spurred by the rapid evolution of the open access (OA) movement. Even though many science journals, traditional and OA, claim to be peer reviewed, the truth is that different levels of peer review occur, and in some cases no, insufficient, or pseudo-peer review takes place. This ultimately leads to the erosion of quality and importance of science, allowing essentially anything to become published, provided that an outlet can be found. In some cases, predatory OA journals serve this purpose, allowing papers to be published, often without any peer review or quality control. In the light of an explosion of such cases in predatory OA publishing, and in severe inefficiencies and possible bias in the peer review of even respectable science journals, as evidenced by the increasing attention given to retractions, there is an urgent need to reform the way in which authors, editors, and publishers conduct the first line of quality control, the peer review. One way to address the problem is through post-publication peer review (PPPR), an efficient complement to traditional peer-review that allows for the continuous improvement and strengthening of the quality of science publishing. PPPR may also serve as a way to renew trust in scientific

Solidification of ion exchange resins saturated with Na+ ions: Comparison of matrices based on Portland and blast furnace slag cement

International Nuclear Information System (INIS)

Lafond, E.; Cau dit Coumes, C.; Gauffinet, S.; Chartier, D.; Stefan, L.; Le Bescop, P.

2017-01-01

This work is devoted to the conditioning of ion exchange resins used to decontaminate radioactive effluents. Calcium silicate cements may have a good potential to encapsulate spent resins. However, certain combinations of cement and resins produce a strong expansion of the final product, possibly leading to its full disintegration. The focus is placed on the understanding of the behaviour of cationic resins in the Na + form in Portland or blast furnace slag (CEM III/C) cement pastes. During hydration of the Portland cement paste, the pore solution exhibits a decrease in its osmotic pressure, which causes a transient expansion of small magnitude of the resins. At 20 °C, this expansion takes place just after setting in a poorly consolidated material and is sufficient to induce cracks. In the CEM III/C paste, swelling of the resins also occurs, but before the end of setting, and induces limited stress in the matrix which is still plastic. - Highlights: • Solidification of cationic resins in the Na + -form is investigated. • Portland and blast furnace slag cements are compared. • Deleterious expansion is observed with Portland cement only. • Resin swelling is due to a decrease in the osmotic pressure of the pore solution. • The consolidation rate of the matrix is a key parameter to prevent damage.

Puzzolanic cements of greater resistance at the attack of selenitic waters than the high sulfate resistance portland cements, and viceverse

Directory of Open Access Journals (Sweden)

Talero, Rafael

1987-09-01

Full Text Available This work confirms the certainty of the predictions of useful service given by Kaluosek and al. for the sulphate resistant portland cements (type V, USA, subject to severe selenitic attack. Two sulphate resistant portland cements, were tested by means of the Le Chatelier Anstett method. The tarts were destroyed at ages of three years, having detected in them the presence of thaumasite by XRD. Even so, the impossibility and possibility thaumasite formation was confirmed in pozzolanic cements tarts, which either had or did not have adequate amount of pozzolana (diatomite for such purpose.

Este trabajo confirman las predicciones de vida útil dadas por Kalousek y colaboradores, para los cementos portland de elevada resistencia al ataque de los iones sulfato (tipo V, USA, sometidos a un severo ataque selenitoso. Se ensayaron dos cementos portland de elevada resistencia al ataque del yeso, mediante el ensayo de Le Chatelier-Anstett. Sus tortas correspondientes se destruyeron a la edad de tres años, habiéndose detectado en las mismas la presencia de thaumasita por DRX. Asimismo se confirmó la imposibilidad y posibilidad de formación de thaumasita en tortas de cementos puzolánicos, los cuales tenían, o no, respectivamente, una adecuada cantidad de puzolana (diatomita para tales fines.

2014 Oregon Department of Geology and Mineral Industries (DOGAMI) Oregon Lidar DEM: Metro Portland, OR

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The dataset encompasses 1221.6 square miles in portions of the greater Portland Metro area in the state of Oregon. The highest hit digital surface models (DSM)...

Physical and microstructural aspects of sulfate attack on ordinary and limestone blended Portland cements

International Nuclear Information System (INIS)

Schmidt, Thomas; Lothenbach, Barbara; Romer, Michael; Neuenschwander, Juerg; Scrivener, Karen

2009-01-01

The consequences of external sulfate attack were investigated by traditional test methods, i.e. length and mass change, as well as by a newly developed, surface sensitive ultrasonic method, using Leaky Rayleigh waves (1 MHz). The macroscopic changes are discussed and compared with thermodynamic calculations and microstructural findings (SEM/EDS). The results show that the main impact of limestone additions on resistance to sulfate degradation are physical - i.e. addition of a few percent in Portland cement reduces the porosity and increases the resistance of Portland cement systems to sulfate; but higher addition of 25% increase porosity and lower resistance to sulfate. The kinetics of degradation were dramatically affected by the solution concentration (4 or 44 g Na 2 SO 4 /l) and the higher concentration also resulted in the formation of gypsum, which did not occur at the low concentration. However the pattern of cracking was similar in both cases and it appears that gypsum precipitates opportunistically in pre-formed cracks so it is not considered as making a significant contribution to the degradation. At 8 deg. C limited formation of thaumasite occurred in the surface region of the samples made from cement with limestone additions. This thaumasite formation led to loss of cohesion of the paste and loss of material from the surface of the samples. However thaumasite formation was always preceded by expansion and cracking of the samples due to ettringite formation and given the very slow kinetics of thaumasite formation it was probably facilitated by the opening up of the structure due to ettringite induced cracking. The expansion of the samples showed a steady stage, followed by a rapidly accelerating stage, with destruction of the samples. The onset of the rapidly accelerating stage occurred when the thickness of the cracked surface layer reached about 1-1.5 mm-10-15% of the total specimen thickness (10 mm).

An Alternative Quality Control Technique for Mineral Chemistry Analysis of Portland Cement-Grade Limestone Using Shortwave Infrared Spectroscopy

Directory of Open Access Journals (Sweden)

Nasrullah Zaini

2016-11-01

Full Text Available Shortwave infrared (SWIR spectroscopy can be applied directly to analyze the mineral chemistry of raw or geologic materials. It provides diagnostic spectral characteristics of the chemical composition of minerals, information that is invaluable for the identification and quality control of such materials. The present study aims to investigate the potential of SWIR spectroscopy as an alternative quality control technique for the mineral chemistry analysis of Portland cement-grade limestone. We used the spectroscopic (wavelength position and depth of absorption feature and geochemical characteristics of limestone samples to estimate the abundance and composition of carbonate and clay minerals on rock surfaces. The depth of the carbonate (CO3 and Al-OH absorption features are linearly correlated with the contents of CaO and Al2O3 in the samples, respectively, as determined by portable X-ray fluorescence (PXRF measurements. Variations in the wavelength position of CO3 and Al-OH absorption features are related to changes in the chemical compositions of the samples. The results showed that the dark gray and light gray limestone samples are better suited for manufacturing Portland cement clinker than the dolomitic limestone samples. This finding is based on the CaO, MgO, Al2O3, and SiO2 concentrations and compositions. The results indicate that SWIR spectroscopy is an appropriate approach for the chemical quality control of cement raw materials.

The Arabic Version of the Mayo-Portland Adaptability Inventory 4: A Validation Study

Science.gov (United States)

Hamed, Razan; Tariah, Hashem Abu; Malkawi, Somaya; Holm, Margo B.

2012-01-01

The Mayo-Portland Adaptability Inventory 4 (MPAI-4) is a valid and reliable assessment tool to detect clinical impairments in patients with acquired brain injury. The tool is widely used by rehabilitation therapists worldwide, given its good psychometric properties and its availability in several languages. The purpose of this study was to…

Relation between Portland cement carbonation, range of clinker burning and some expansive phenomena in the autoclave test

Directory of Open Access Journals (Sweden)

Ruiz de Cauna, A.

1975-12-01

Full Text Available Not availableEn este trabajo se estudia el doble pico que aparece en la región de altas temperaturas de las curvas derivatométricas, realizadas en atmósfera de vapor de agua, de los cementos portland anhidros e hidratados y en general el efecto de la carbonatación sobre los silicatos y aluminatos presentes en los cementos portland, especialmente sobre el perfil de las curvas derivatométricas de los cementos portland anhidros e hidratados. Se recogen y examinan los cambios experimentados en el doble pico al someter los cementos a la acción de diversos tratamientos y de agentes modificantes, tales como el tiempo, el CO2, la hidratación normal, las hidrataciones bajo agua a ebullición, en autoclave y en suspensión acuosa con agitación, la adición de puzolana y de fuertes proporciones de S04Ca. Se estudia y compara, asimismo, el comportamiento al análisis térmico bajo vapor de agua y al ensayo de autoclave de algunos clínkeres y cementos que presentan el doble pico en forma acusada y poco apreciable, respectivamente. De los resultados obtenidos se deducen conclusiones que explican los comportamientos experimentales observados. Las principales conclusiones se refieren a la interpretación de los picos que aparecen en las curvas derivatométricas o de velocidad de pérdida de peso de los cementos portland anhidros e hidratados, y a algunos aspectos de su carbonatación, a la probable existencia de un compuesto intermedio, consecuencia de la incompleta formación del silicato tricálcico y a la explicación de determinadas grandes expansiones producidas en el ensayo de autoclave.

A thermodynamic approach to the hydration of sulphate-resisting Portland cement

International Nuclear Information System (INIS)

Lothenbach, Barbara; Wieland, Erich

2006-01-01

A thermodynamic approach is used to model changes in the hydrate assemblage and the composition of the pore solution during the hydration of calcite-free and calcite-containing sulphate-resisting Portland cement CEM I 52.5 N HTS. Modelling is based on thermodynamic data for the hydration products and calculated hydration rates for the individual clinker phases, which are used as time-dependent input parameters. Model predictions compare well with the composition of the hydrate assemblage as observed by TGA and semi-quantitative XRD and with the experimentally determined compositions of the pore solutions. The calculations show that in the presence of small amounts of calcite typically associated with Portland cement, C-S-H, portlandite, ettringite and calcium monocarbonate are the main hydration products. In the absence of calcite in the cement, however, siliceous hydrogarnet instead of calcium monocarbonate is observed to precipitate. The use of a higher water-to-cement ratio for the preparation of a calcite-containing cement paste has a minor effect on the composition of the hydrate assemblage, while it significantly changes the composition of the pore solution. In particular, lower pH value and higher Ca concentrations appear that could potentially influence the solubility and uptake of heavy metals and anions by cementitious materials

Effectiveness of shrinkage-reducing admixtures on Portland pozzolan cement concrete

Directory of Open Access Journals (Sweden)

Videla, C.

2005-06-01

Full Text Available Drying shrinkage causes tensile stress in restrained concrete members. Since all structural elements are subject to some degree of restraint, drying shrinkage is regarded to be one of the main causes of concrete cracking. The purpose of the present study was to evaluate the effectiveness of SRA in reducing drying shrinkage strain in Portland pozzolan cement concrete. The major variables examined included slump, admixture type and dose, and specimen size. The measured results indicate that any of the admixtures used in the study significantly reduced shrinkage. Concrete manufactured with shrinkage reducing admixtures shrank an average of 43% less than concrete without admixtures. As a rule, the higher the dose of admixture, the higher was its shrinkage reduction performance. The experimental results were compared to the shrinkage strain estimated with the ACI 209, CEB MC 90, B3, GL 2000, Sakata 1993 and Sakata 2001 models. Although none of these models was observed to accurately describe the behaviour of Portland pozzolan cement concrete with shrinkage reducing admixtures, the Sakata 2001 model, with a weighted coefficient of variation of under 30%, may be regarded to be roughly adequate.

La retracción por secado es un fenómeno intrínseco del hormigón que produce tensiones de tracción en elementos restringidos de hormigón. Puesto que todos los elementos presentan algún grado de retracción, se considera a la retracción por secado como una de las principales causas de agrietamiento en proyectos de construcción en hormigón. Por lo tanto, el objetivo de esta investigación fue evaluar la efectividad de los aditivos reductores de retracción (SRA en hormigones fabricados con cemento Portland puzolánico. Las variables principales estudiadas incluyen el asentamiento de cono de Abrams, marca y dosis de aditivo reductor de retracción, y tamaño de espécimen de hormigón. Los resultados obtenidos permiten concluir que el uso de

Addition of polyurethane dispersions to Portland G for oil wells steam injection submitted to vapor injection; Adicao de poliuretana em dispersao a Portland G para cimentacao de pocos de petroleo sujeitos a injecao de vapor

Energy Technology Data Exchange (ETDEWEB)

Silva, L.B. da; Lima, F.M. de; Martinelli, A.M.; Bezerra, U.T.; Mello, D.M.A. [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil); Araujo, R.G.S. [PETROBRAS, Rio de Janeiro, RJ (Brazil)

2004-07-01

Portland cement is by far the most important binding material used in oil well cementing. The cement sheath is responsible for both the mechanical stability of the wellbore and zonal isolation. During primary cementing and the production lifespan of the well, the cement sheath is exposed to adverse thermo-mechanical conditions, which may crack the intrinsically brittle cement material. Cracking affects the mechanical integrity of the sheath resulting in the contamination of oil or gas pay zones, as well as in the increase of producing costs related to the extraction of pebble and water. This scenario is especially encountered in wells containing heavy oils, typical of the Northeastern region of Brazil. The objective of the present study was to improve the fracture toughness of hardened Special Portland Cement slurries by the addition of aqueous polyurethane to Portland-based slurries used in primary cementing, plug backs and squeeze operations, improving environmental and economical impacts. The results revealed that the addition of polyurethane increased the viscosity of the slurry but still within the limits established by oil well cement guidelines. No significant increase was observed in the compressive strength of the cement. However, the addition of polyurethane improved the toughness of the cement increasing its ability to withstand thermo-mechanical cycles typical of heavy oil recovery. In addition, significant reduction in permeability was observed as the contents of polyurethane increased, contributing to the reduction in set time and gas migration through the cement sheath. (author)

Influence of bismuth oxide concentration on the pH level and biocompatibility of white Portland cement.

Science.gov (United States)

Marciano, Marina Angélica; Garcia, Roberto Brandão; Cavenago, Bruno Cavalini; Minotti, Paloma Gagliardi; Midena, Raquel Zanin; Guimarães, Bruno Martini; Ordinola-Zapata, Ronald; Duarte, Marco Antonio Hungaro

2014-01-01

To investigate if there is a relation between the increase of bismuth oxide and the decrease of pH levels and an intensification of toxicity in the Portland cement. White Portland cement (WPC) was mixed with 0, 15, 20, 30 and 50% bismuth oxide, in weight. For the pH level test, polyethylene tubes were filled with the cements and immersed in Milli-Q water for 15, 30 and 60 days. After each period, the increase of the pH level was assessed. For the biocompatibility, two polyethylene tubes filled with the cements were implanted in ninety albino rats (n=6). The analysis of the intensity of the inflammatory infiltrate was performed after 15, 30 and 60 days. The statistical analysis was performed using the Kruskal-Wallis, Dunn and Friedman tests for the pH level and the Kruskal-Wallis and Dunn tests for the biological analysis (p0.05). For the inflammatory infiltrates, no significant statistical differences were found among the groups in each period (p>0.05). The 15% WPC showed a significant decrease of the inflammatory infiltrate from 15 to 30 and 60 days (pPortland cement did not affect the pH level and the biological response. The concentration of 15% of bismuth oxide resulted in significant reduction in inflammatory response in comparison with the other concentrations evaluated.

The Influence of Diatomite on the Strength and Microstructure of Portland Cement

Directory of Open Access Journals (Sweden)

Liu Jun

2016-01-01

Full Text Available To study the influence of the types and mixing amount of diatomite on the Portland cement, we prepared the cement specimen doped with the calcined first-grade, first-grade and second-grade diatomite ,tested the 3d, 7d, 14d compressive strength, and studied and discussed phase, structure and morphology of diatomite in the binary system by the method of XRD, SEM . Experimental results show that with the addition of diatomite, the strength of cement paste increase; the optimal contents of calcined first-grade ,first-grade and second-grade diatomite in Portland cement are 5%,Compared to the blank group, the strength of specimen can be increased by 54.6%, 15.4% and 10.2%, respectively; At the same time ,the 7d microscopic hydration of different diatomite particles were analyzed through the experiment , and the shell of calcined diatomite particles were better hydrated than that of first-grade and second-grade diatomite particles. The results indicate that the diatomite can improve the strength of cement paste, the hydration of different diatomite particles can influence the growth of cement paste strength.

Characteristics of novel root-end filling material using epoxy resin and Portland cement.

Science.gov (United States)

Lee, Sang-Jin; Chung, Jin; Na, Hee-Sam; Park, Eun-Joo; Jeon, Hyo-Jin; Kim, Hyeon-Cheol

2013-04-01

The aim of this study was to evaluate the physical properties and cytotoxicity of a novel root-end filling material (EPC) which is made from epoxy resin and Portland cement as a mineral trioxide aggregate (MTA) substitute. EPC, developed as a root-end filling material, was compared with MTA and a mixture of AH Plus sealer and MTA (AMTA) with regard to the setting time, radio-opacity, and microleakage. Setting times were evaluated using Vicat apparatus. Digital radiographs were taken to evaluate the aluminium equivalent radio-opacity using an aluminium step wedge. Extracted single-rooted teeth were used for leakage test using methylene blue dye. After canal shaping and obturation, the apical 3-mm root was resected, and a root-end cavity with a depth of 3 mm was prepared. The root-end cavities were filled with MTA, AMTA, and EPC for 15 specimens in each of three groups. After setting in humid conditions for 24 h, the specimens were tested for apical leakage. For evaluation of the biocompatibility of EPC, cell (human gingival fibroblast) viability was compared for MTA and Portland cement by MTT assay, and cell morphological changes were compared for MTA and AH Plus by fluorescence microscopy using DAPI and F-actin staining. The setting time, radio-opacity, and microleakage were compared using one-way ANOVA and Scheffe's post hoc comparison, and the cytotoxicity was compared using the nonparametric Kruskal-Wallis rank sum test. Statistical significance was set at 95%. EPC had a shorter setting time and less microleakage compared with MTA (p Portland cement, was found to be a useful material for root-end filling, with favourable radio-opacity, short setting time, low microleakage, and clinically acceptable low cytotoxicity. The novel root-end filling material would be a potentially useful material for a surgical endodontic procedure with favourable properties.

Effect of calcium/silicon ratio on retention of uranium (VI) in portland cement materials

International Nuclear Information System (INIS)

Tan Hongbin; Li Yuxiang

2005-01-01

Calcium silicate hydrate (CSH) materials of varied calcium to silicon (Ca/Si) ratios were prepared by hydrothermal synthesis at 80 degree C, with calcium oxide and micro-silicon employed. These products were determined to be of gel phase by XRD. Leaching tests with 1% hydrochloric acid indicated that more Uranium (VI) was detained by CSH with lower Ca/Si ratios. Alkali-activated slag cement (with a lower Ca/Si ratio) was found to have a stronger retention capacity than Portland cement (with a higher Ca/Si ratio), at 25 degree C in 102-days leaching tests with simulated solidified forms containing Uranium (VI). The accumulative leaching fraction of Uranium (VI) for Alkali-activated slag cement solidified forms is 17.6% lower than that for Portland cement. The corresponding difference of diffusion coefficients is 40.6%. This could be correlated with the difference of Ca/Si ratios between cements of two kinds. (authors)

Measurement of the leaching rate of radionuclide 134Cs from the solidified radioactive sources in Portland cement mixed with microsilica and barite matrixes

International Nuclear Information System (INIS)

Shaaban, Ismail; Assi, Nasim

2011-01-01

Portland cement was mixed with radionuclide 134 Cs to produce low-level radioactive sources. These sources were surrounded with cement mixed with different materials like microsilica and barite. The leaching rate of 134 Cs from the solidified radioactive source in Portland cement alone was found to be 4.481 x 10 -4 g/cm 2 per day. Mixing this Portland cement with microsilica and with barite reduced significantly the leaching rate to 1.091 x 10 -4 g/cm 2 per day and 3.153 x 10 -4 g/cm 2 per day for 1 wt.% mixing, and to 1.401 x 10 -5 g/cm 2 per day and 1.703 x 10 -4 g/cm 2 per day for 3 wt.% mixing, respectively. It was also found that the application of a latex paint reduced these leaching rates by about 6.5%, 20.3% and 13.3% for Portland cement, cement mixed with microsilica and with barite, respectively. The leaching data were also analyzed using the polynomial method. The obtained results showed that cement mixed with microsilica and with barite can be effectively used for radioactive sources solidification.

Durabilidad de un suelo contaminado y tratado con cemento portland Durability of a contaminated soil treated with portland cement

Directory of Open Access Journals (Sweden)

José W Jiménez Rojas

2008-01-01

Full Text Available Este trabajo tiene por objetivo la aplicación de la técnica de solidificación/estabilización de suelos contaminados, analizando específicamente el comportamiento físico del suelo a través de ensayos de durabilidad. El suelo fue contaminado en laboratorio con residuo oleoso y la aplicación de la técnica tuvo cómo agente de encapsulamiento el cemento Portland CP V-ARI. Los ensayos de durabilidad, realizados según la NBR 13554 (1996, tuvieron como objetivo estudiar el grado de desagregación y vulnerabilidad del material con diversas combinaciones de dosificaciones de cemento y residuo oleoso, así cómo estudiar la variación volumétrica de los mismos. A partir de los resultados es posible observar que cuanto mayor la cantidad de contaminante, mayor es la pérdida de masa. Sin embargo, cuánto mayor es la cantidad de cemento, menor es la pérdida de masa y menor la variación volumétrica.This work seeks the application of solidification/stabilization techniques to contaminated soils analyzing specifically de physical behavior of the soil through tests of durability. The soil was contaminated in laboratory with acidic oily sludge industrial residues and the application of that technique had an encapsulate agent, the Portland cement CP V-ARI. The tests were carried out according to NBR 13.554 (1996, and they aimed to study the level of degradation and the vulnerability of the material with several combinations of cement and acidic oily sludge as well as study their volumetric variations. Starting from the results, it is possible to observe that the larger the contamination the larger the mass loss; however the larger the amount of cement, the smaller the mass loss and the more stable the volumetric variation.

Properties of expansive cements, made with Portland cement, gypsum and high alumina cement

Directory of Open Access Journals (Sweden)

Monfore, G. E.

1966-03-01

Full Text Available Not availableLos cementos expansivos se han desarrollado durante las tres décadas pasadas, principalmente por las investigaciones llevadas a cabo en Francia, URSS y Estados Unidos. Los cementos expansivos que fueron utilizados en los estudios de los cuales se da cuenta en el presente trabajo se obtuvieron mediante la mezcla de cemento Portland, cemento aluminoso y yeso. En las investigaciones se utilizaron morteros con los cuales se pudo determinar los efectos de la composición, tiempo y temperatura de curado sobre las resistencias, dilatación libre, retracción y desarrollo de resistencias en probetas pretensadas. Se hace una revisión sobre los estudios hechos con cementos expansivos y desarrollados en la Universidad de California. Las propiedades de taIes hormigones son, en términos generales, comparables a aquellos obtenidos con mezclas de cementos portland, cemento aluminoso y yeso. Es necesaria más información sobre pérdidas de tensión en los aceros y durabilidad de los hormigones autopretensados.

Radioactive waste-Portland cement systems: I, radionuclide distribution

International Nuclear Information System (INIS)

Jantzen, C.M.; Glasser, F.P.; Lachowski, E.E.

1984-01-01

Crystal chemical stabilization of radioactive wastes can be achieved during clinkering of, or with, ordinary portland cement. Waste loadings of 20 to 30 wt% are achieved by dilute solid solution of waste ions into cementitious host lattices. Higher waste loadings result in compatible noncementitious radiophases. The cementitious phases hydrate without loss of compressive strength. Crystallochemical relationships predict that the radionuclide partitioning in the anhydrous clinkered phases will be maintained in the hydration products. These cementitious hydroxylated radiophases would be in internal equilibrium under anticipated repository conditions. The radionuclide distributions observed are described in the context of established phase equilibria for commercial waste cement systems, but are applicable to transuranic, medium- and low-level wastes

Winter Storm Jupiter of January 2017: Meteorological Drivers, Synoptic Evolution, and Climate Change Considerations in Portland, Oregon

Science.gov (United States)

Dean, S.; Loikith, P. C.

2017-12-01

Although the Pacific Northwest has some of the highest wintertime precipitation in the United States, most urban areas receive little in the way of snow. While 37 inches of wintertime rain fall in Portland on average annually, the city only receives four inches of snow on average. Although wintertime extreme snowstorm events are rare in Portland, in the last century they have occurred about once every ten years. On January 10-12th, 2017, winter storm Jupiter brought 11 inches of snow to downtown Portland within a 12-hour period, making it the largest snowstorm for the city in twenty years. The city declared a state of emergency, over 30,000 citizens lost power, and thousands of businesses were forced to shut down. The anomalously cold air and high amounts of snowfall in a short amount of time made the storm different from others in recent years. This study aims to discover the meteorological drivers behind the January 2017 snowstorm in Portland, Oregon. We also aim to understand how this storm compared with other local storms in the past, and assess the likelihood of a similar event occurring in the future. To do this, reanalysis data were used to display the synoptic evolution of the January 2017 storm. We compared this storm with two other extreme snowfall events from December 2008 and January 1980, assessing meteorological similarities and differences between storms. Results show that the 2017 event was associated with a slow moving, strong low-pressure system accompanied by a 500 hPa trough. These large-scale features helped drive slow moving, locally heavy snow bands over the city of Portland. At the same time, an unusually strong Arctic high-pressure system moved into the interior Pacific Northwest allowing for strong cold air advection west through the Cascade Mountain Range and Columbia River Gorge. Temperature trends show warming of 1-2 °C in the Pacific Northwest since the middle of the last century. Because of this, uncertainty associated with

Evaluation of the effect of intrinsic material properties and ambient conditions on the dimensional stability of white mineral trioxide aggregate and Portland cement.

Science.gov (United States)

Camilleri, Josette

2011-02-01

A number of factors affect the dimensional stability of a material. These factors include curing conditions, material solubility, leaching, and time. The aim of this study was to evaluate the restrained dimensional change in the vertical direction as a function of the ambient conditions, fluid uptake, solubility, and leaching of white mineral trioxide aggregate (MTA) and Portland cement stored in Hank's balanced salt solution (HBSS) over a period of 28 days. The dimensional change in the vertical direction over a 28-day period was determined using a linear variable differential transducer (LVDT) on laterally restrained test samples. The fluid uptake and solubility of both MTA and Portland cement was also evaluated. The leaching in water and HBSS was assessed using inductively coupled plasma. MTA was more soluble than Portland cement. Both materials absorbed water and physiological solution, with Portland cement displaying a lower uptake than MTA. Both cements exhibited a net expansion when in contact with a physiological solution and released high levels of calcium. MTA leached bismuth. Both calcium and bismuth ion release was higher in HBSS than in water. Phosphorus ions in HBSS were depleted when in contact with both MTA and Portland cement. The MTA was very susceptible to ambient conditions. The addition of bismuth oxide to MTA reduced the leaching of calcium hydroxide, increased the material solubility, and caused deterioration in material dimensional stability. Further research is necessary to establish the material porosity and its effect on the dimensional stability. Copyright © 2011 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Solidification of ion exchange resins saturated with Na{sup +} ions: Comparison of matrices based on Portland and blast furnace slag cement

Energy Technology Data Exchange (ETDEWEB)

Lafond, E. [CEA, DEN, DTCD, SPDE, F-30207 Bagnols-sur-Cèze cedex (France); Cau dit Coumes, C., E-mail: celine.cau-dit-coumes@cea.fr [CEA, DEN, DTCD, SPDE, F-30207 Bagnols-sur-Cèze cedex (France); Gauffinet, S. [Laboratoire Interdisciplinaire Carnot de Bourgogne UMR 6303 CNRS-Université de Bourgogne, Dijon, France, 9 Av Alain Savary, BP 47870, 21078 Dijon cedex (France); Chartier, D. [CEA, DEN, DTCD, SPDE, F-30207 Bagnols-sur-Cèze cedex (France); Stefan, L. [AREVA, Back End Business Group, Dismantling & Services, 1 Place Jean Millier, 92084 Paris La Défense (France); Le Bescop, P. [CEA, DEN, DPC, SECR, F-91192 Gif-sur-Yvette (France)

2017-01-15

This work is devoted to the conditioning of ion exchange resins used to decontaminate radioactive effluents. Calcium silicate cements may have a good potential to encapsulate spent resins. However, certain combinations of cement and resins produce a strong expansion of the final product, possibly leading to its full disintegration. The focus is placed on the understanding of the behaviour of cationic resins in the Na{sup +} form in Portland or blast furnace slag (CEM III/C) cement pastes. During hydration of the Portland cement paste, the pore solution exhibits a decrease in its osmotic pressure, which causes a transient expansion of small magnitude of the resins. At 20 °C, this expansion takes place just after setting in a poorly consolidated material and is sufficient to induce cracks. In the CEM III/C paste, swelling of the resins also occurs, but before the end of setting, and induces limited stress in the matrix which is still plastic. - Highlights: • Solidification of cationic resins in the Na{sup +}-form is investigated. • Portland and blast furnace slag cements are compared. • Deleterious expansion is observed with Portland cement only. • Resin swelling is due to a decrease in the osmotic pressure of the pore solution. • The consolidation rate of the matrix is a key parameter to prevent damage.

Preparation and Physical Assessment of Portland Cement Base Composites Containing Nano Particles

OpenAIRE

Amir Mahmoudi

2015-01-01

In this research the effects of adding silica and alumina nanoparticles on flow ability and compressive strength of cementitious composites based on Portland cement were investigated. In the first stage, the rheological behavior of different samples containing nanosilica, nanoalumina and polypropylene, polyvinyl alcohol and polyethylene fibers were evaluated. With increasing of nanoparticles in fresh samples, the slump flow diameter reduced. Fibers reduced the flow abilit...

Manufacturing of mortars and concretes non-traditionals, by Portland cement, metakaoline and gypsum (15.05%

Directory of Open Access Journals (Sweden)

Talero, R.

1999-12-01

Full Text Available In a thorough previous research (1, it appeared that creation, evolution and development of the values of compressive mechanical strength (CS and flexural strength (FS, measured in specimens 1x1x6cm of mortar type ASTM C 452-68 (2, manufactured by ordinary Portland cement P-1 (14.11% C₃A or PY-6 (0.00% C₃A, metakaolin and gypsum (CaSO₄∙2H₂O -or ternary cements, CT-, were similar to the ones commonly developed in mortars and concretes of OPC. This paper sets up the experimental results obtained from non-traditional mortars and concretes prepared with such ternary cements -TC-, being the portland cement/metakaolin mass ratio, as follows: 80/20, 70/30 and 60/40. Finally, the behaviour of these cements against gypsum attack, has been also determined, using the following parameters: increase in length (ΔL%, compressive, CS, and flexural, FS, strengths, and ultrasound energy, UE. Experimental results obtained from these non-traditional mortars and concretes, show an increase in length (ΔL, in CS and FS, and in UE values, when there is addition of metakaolin.

En una exhaustiva investigación anterior (1, se pudo comprobar que la creación, evolución y desarrollo de los valores de resistencias mecánicas a compresión, RMC, y flexotracción, RMF, proporcionados por probetas de 1x1x6 cm, de mortero 1:2,75, selenitoso tipo ASTM C 452-68 (2 -que habían sido preparadas con arena de Ottawa, cemento portland, P-1 (14,11% C₃A o PY- 6 (0,00% C₃A, metacaolín y yeso (CaSO₄∙2H₂O-, fue semejante a la que, comúnmente, desarrollan los morteros y hormigones tradicionales de cemento portland. En el presente trabajo se exponen los resultados experimentales obtenidos de morteros y hormigones no tradicionales, preparados con dichos cementos ternarios, CT, siendo las proporciones porcentuales en masa ensayadas, cemento portland/metacaolín, las siguientes: 80/20, 70

Hydration rate and strength development of low-heat type portland cement mortar mixed with pozzolanic materials

International Nuclear Information System (INIS)

Matsui, Jun

1998-01-01

Recently, low-heat type Portland cement was specified in Japan Industrial Standards (JIS). Its hydration proceeds slowly. The results of the research so far obtained indicate that slow hydration of cement and mixing of pozzolanic materials with cement make micro-structure of harded cement paste dense and durable. In this study, a blended cement using low-heat type Portland cement and some of pozzolanic materials has been newly developed and its strength property and hydration ratio were checked. The followings are conclusion. (1) Hydration rate of cement paste varies with the replacement ratio of pozzolanic materials. (2) A good liner relationship between strength and total hydration rate of cement paste was observed. (3) A proper replacement ratio of both base-cement and pozzolanic material for manufacturing a blended cement is 50%. (author)

Phased-Resolved Strain Measuremetns in Hydrated Ordinary Portland Cement Using Synchrotron x-Rays (Prop. 2003-033)

International Nuclear Information System (INIS)

Biernacki, Joseph J.; Watkins, Thomas R.; Parnham, C.J.; Hubbard, Camden R.; Bai, J.

2006-01-01

X-ray diffraction methods developed for the determination of residual stress states in crystalline materials have been applied to study residual strains and strains because of mechanical loading of ordinary portland cement paste. Synchrotron X-rays were used to make in situ measurements of interplanar spacings in the calcium hydroxide (CH) phase of hydrated neat portland cement under uniaxial compression. The results indicate that strains on the order of 1/100 000 can be resolved providing an essentially new technique by which to measure the phase-resolved meso-scale mechanical behavior of cement under different loading conditions. Evaluation of these strain data in view of published elastic parameters for CH suggests that the CH carries a large fraction of the applied stress and that plastic interactions with the matrix are notable.

Parameters of Alumina Cement and Portland Cement with Addition of Chalcedonite Meal

Science.gov (United States)

Kotwa, Anna

2017-10-01

Aluminous cement is a quick binder with special properties. It is used primarily to make non-standard monolithic components exposed to high temperatures, + 1300°C. It is also a component of adhesives and mortars. It has a very short setting time. It is characterized by rapid increase in mechanical strength and resistance to aggressive sulphates. It can be used in reinforced concrete structures. Laying of concrete, construction mortar made of alumina cement can be carried out even at temperatures of -10°C. This article discusses a comparison of the parameters of hardened mortar made of alumina cement GÓRKAL 40 and Portland cement CEM I 42.5R. The mortars contain an addition of chalcedonite meal with pozzolanic properties, with particle size of less than 0.063μm. The meal was added in amounts of 5% and 20% of cement weight. Chalcedonite meal used in the laboratory research is waste material, resulting from chalcedonite aggregate mining. It has the same properties as the rock from which it originates. We have compared the parameters of hardened mortar i.e. compressive strength, water absorption and capillarity. The addition of 20% chalcedonite meal to mortars made from aluminous cement will decrease durability by 6.1% relative to aluminous cement mortar without addition of meal. Considering the results obtained during the absorbency tests, it can be stated that the addition of chalcedonite meal reduces weight gains in mortars made with cement CEM I 42.5 R and alumina cement. Use of alumina cement without addition of meal in mortars causes an increase of mass by 248% compared to Portland cement mortars without additions, in the absorption tests. The addition of chalcedonite meal did not cause increased weight gain in the capillary action tests. For the alumina cement mortars, a lesser weight gains of 24.7% was reported, compared to the Portland cement mortar after 28 days of maturing.

Alkali segregation in Portland cement pastes

Directory of Open Access Journals (Sweden)

Triviño, F.

1966-09-01

Full Text Available Not availableEn el presente trabajo se pone de manifiesto experimentalmente la formación y presencia de aphthitalita -sulfato doble de potasio y sodio en la relación S04K2/S04Na2 = 3/1 en las pastas puras de cemento portland, desde el comienzo del fraguado de las mismas. Se estudia el mecanismo de la citada formación, íntimamente relacionada con el proceso general de formación de eflorescencias salinas, a base de una emigración de sulfatos alcalinos hacia las partes externas de las pastas, en virtud de fenómenos de exudación equivalentes a arrastres capilares. Se sintetiza y aísla la aphthitalita por dos procedimientos y se obtiene su difractograma.de rayos· X, a efectos de su identificación y de la confirmación de los resultados experimentales obtenidos, así como de la interpretación de los mismos.

The public and wildland fire management: social science findings for managers

Science.gov (United States)

S.M. McCaffrey

2006-01-01

Presents key social science findings from three National Fire Plan-sponsored research projects. Articles highlight information of likely interest to individuals working to decrease wildfire hazards on both private and public lands. Three general topic areas are addressed: (1) public views and acceptance of fuels management, (2) working with homeowners and communities,...

Portland's experience with land use tools to promote green roofs

International Nuclear Information System (INIS)

Johnson, M.

2004-01-01

In the late 1990s, the City of Portland, Oregon faced environmental challenges that prompted the City to mandate environmentally sensitive development. Several programs were developed in response to these challenges, some of which resulted in the creation of land use policies and incentives that promote green roofs. Zoning code provisions were adopted in 2001 to promote eco-roofs in an effort to reduce stormwater runoff, mitigate urban heat island effects, provide habitat for birds, and improve air quality and energy efficiency. The Central City Fundamental Design Guidelines were also revised to encourage eco-roof development. In 2002, the South Waterfront Plan was created to integrate ecological design into an urban environment through sustainability principles and practices. Land use tools were developed to introduce developers to an approach that reduced energy costs and stormwater costs, while also contributing to a project's marketability. These tools were created with the support of programs and policies such as the CSO (Combined Sewer Overflow) Program; eco-roof research which began in 1995 to determine the stormwater management potential of eco-Green roofs; technical assistance to encourage and highlight sustainable development practices; the Stormwater Management Manual that set standards for the amount and quality of stormwater runoff leaving development sites; the G/Rated Program that offers resources for green building practices; the Green Investment Fund that supports the G/Rated Program; and, the Portland Development Commission Green Building Policy financing tool for earth-friendly designs and materials. 34 refs., 2 figs

Flow properties of MK-based geopolymer pastes. A comparative study with standard Portland cement pastes.

Science.gov (United States)

Favier, Aurélie; Hot, Julie; Habert, Guillaume; Roussel, Nicolas; d'Espinose de Lacaillerie, Jean-Baptiste

2014-02-28

Geopolymers are presented in many studies as alternatives to ordinary Portland cement. Previous studies have focused on their chemical and mechanical properties, their microstructures and their potential applications, but very few have focussed on their rheological behaviour. Our work highlights the fundamental differences in the flow properties, which exist between geopolymers made from metakaolin and Ordinary Portland Cement (OPC). We show that colloidal interactions between metakaolin particles are negligible and that hydrodynamic effects control the rheological behaviour. Metakaolin-based geopolymers can then be described as Newtonian fluids with the viscosity controlled mainly by the high viscosity of the suspending alkaline silicate solution and not by the contribution of direct contacts between metakaolin grains. This fundamental difference between geopolymers and OPC implies that developments made in cement technology to improve rheological behaviour such as plasticizers will not be efficient for geopolymers and that new research directions need to be explored.

Comparative evaluation of antimicrobial action of MTA, calcium hydroxide and Portland cement Avaliação comparativa da ação antimicrobiana do MTA, hidróxido de cálcio e cimento Portland

Directory of Open Access Journals (Sweden)

Caroline Sousa Ribeiro

2006-10-01

Full Text Available The present study aimed to evaluate and compare the antimicrobial effect of MTA Dentsply, MTA Angelus, Calcium Hydroxide and Portland cement. Four reference bacterial strains were used: Pseudomonas aeruginosa, Escherichia coli, Bacteroides fragilis, and Enterococcus faecalis. Plates containing Mueller-Hinton agar supplemented with 5% sheep blood, hemin, and menadione were inoculated with the bacterial suspensions. Subsequently, wells were prepared and immediately filled with materials and incubated at 37ºC for 48 hours under anaerobic conditions, except P. aeruginosa. The diameters of inhibition zones were measured, and data analyzed using ANOVA and the Tukey test with 1% level of significance. MTA Dentsply, MTA Angelus and Portland cement inhibited the growth of P. aeruginosa. Calcium Hydroxide was effective against P. aeruginosa and B. fragillis. Under anaerobic conditions, which may hamper the formation of reactive oxygen species, the materials failed to inhibit E. faecalis, and E. coli.O objetivo do presente trabalho foi avaliar e comparar o efeito antimicrobiano do MTA Dentsply, MTA Angelus, hidróxido de cálcio e cimento Portland sobre quatro cepas bacterianas: Pseudomonas aeruginosa, Escherichia coli, Bacteroides fragilis, e Enterococcus faecalis. Placas contendo agar Muller-Hinton suplementadas com 5% de sangue de carneiro, hemina e menadiona foram inoculadas com as suspensões bacterianas. Poços foram confeccionados com auxílio de perfuradores e imediatamente preenchidos com os materiais, e incubados a 37ºC por 48 horas em atmosfera de anaerobiose, exceto P. aeruginosa. O diâmetro dos halos de inibição foi medido e os dados analisados usando o teste estatístico ANOVA e o de Tukey com nível de significância de 1%. O MTA Dentsply, MTA Angelus e Cimento Portland inibiram o crescimento da P.aeruginosa. O hidróxido de cálcio foi efetivo contra P. aeruginosa e B. fragillis. Sob atmosfera de anaerobiose, condição que pode

Immobilization of citric acid solutions in portland cement; Imobilizacao de solucoes de acido citrico em cimento Portland

Energy Technology Data Exchange (ETDEWEB)

Lopes, Valdir M.; Rzyski, Barbara M. [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil)

1997-12-01

Decontamination processes by using citric acid on certain items used in the nuclear area, can result in large volumes of liquid wastes with low activity or effluents, contaminated with uranium and some elements dangerous to the environment. A great number of installations that have decontamination processes adopt the zero discharge philosophy. So, one of the forms to isolate the solutions is by reducing its volume through the evaporation process. The generated must can be neutralized and encapsulated or immobilized in Portland cement. This work propose a chemical technique to destroy the citric acid in the decontamination solutions instead of neutralization and, depending on the installation convenience, a direct cement immobilization of these solutions or of the evaporation mud. The results obtained in this work involve data about the workability, setting time and mechanical resistance, after 28 days of sealed cure, for samples with water-cement ratios of 4, 0.5 and 0.6, by weight. (author). 5 refs., 2 tabs.

Influence of moisture condition on chloride diffusion in partially saturated ordinary Portland cement mortar

NARCIS (Netherlands)

Zhang, Y.; Zhang, M.; Ye, G.

2018-01-01

Experiments have been carried out to study the influence of moisture condition, including moisture content and its distribution, on the chloride diffusion in partially saturated ordinary Portland cement mortar. The mortar samples with water-to-cement (w/c) ratios of 0.4, 0.5 and 0.6, cured for 1

The impact of zirconium oxide radiopacifier on the early hydration behaviour of white Portland cement

International Nuclear Information System (INIS)

Coleman, Nichola J.; Li, Qiu

2013-01-01

Zirconium oxide has been identified as a candidate radiopacifying agent for use in Portland cement-based biomaterials. During this study, the impact of 20 wt.% zirconium oxide on the hydration and setting reactions of white Portland cement (WPC) was monitored by powder X-ray diffraction (XRD), 29 Si and 27 Al magic angle spinning nuclear magnetic resonance spectroscopy (MAS NMR), transmission electron microscopy (TEM) and Vicat apparatus. The presence of 20 wt.% zirconium oxide particles in the size-range of 0.2 to 5 μm was found to reduce the initial and final setting times of WPC from 172 to 147 min and 213 to 191 min, respectively. Zirconium oxide did not formally participate in the chemical reactions of the hydrating cement; however, the surface of the zirconium oxide particles presented heterogeneous nucleation sites for the precipitation and growth of the early C-S-H gel products which accelerated the initial setting reactions. The presence of zirconium oxide was found to have little impact on the development of the calcium (sulpho)aluminate hydrate phases. - Highlights: ► This is the first study of Portland cement-based biomaterials by 27 Al and 29 Si NMR. ► 20 wt.% ZrO 2 radiopacifier accelerates the early cement hydration reactions. ► Extent of hydration after 6 h is increased from 5.7% to 15% in the presence of ZrO 2 . ► Initial and final setting times are reduced by 25 and 22 min, respectively. ► ZrO 2 provides nucleation sites for the precipitation of early hydration products.

Pembuatan dan Pengujian Kualitas Semen Portland Yang Diperkaya Silikat Abu Ampas Tebu

OpenAIRE

Suci Wulandari, Indah Pratama

2015-01-01

Penelitian ini mengkaji pengaruh penambahan abu ampas tebu terhadap kuat tekan mortar dan sifat fisis semen portland komposit, meliputi: kehalusan semen, kebutuhan air semen, waktu pengikatan semen, pemuaian dan komposisi kimia semen. Dari hasil penelitian, besar kuat tekan pada penggunaan abu ampas tebu dengan kadar 9% merupakan penambahan optimum pada mortar yang direndam larutan kapur jenuh Sedangkan dari hasil pengujian fisis yang meliputi kehalusan semen, kebutuhan air semen, waktu pengi...

The influence of the amount addition and kind of the active silica fume in the mechanical properties of the cement Portland concrete

International Nuclear Information System (INIS)

Silva, I.J. da; Melo, A.B. de; Liborio, J.B.L.; Souza, M.F. de

1998-01-01

This study presents an evaluation of the influence of the amount addition and of active silica type deriving from residues of the production of Iron-Silicon alloys of brasilian industries, on the mechanical properties of the concrete made with basaltic aggregates with D max ≥9,5 mm using Portland cements CP II E 32. The study has for objective to evaluate the efficiency of the active silica on the mechanical resistance of the high performance concrete (CAD), when used in substitution of the Portland cement, even so maintaining the same amount of agglomerant material. They are appraised amount of 5%, 8%, 10%, 12% and 15% of active silica in relation to Portland cement mass. The results suggest that for the appraised silicas there is little efficiency. Other aspects related to the mixtures just with addictive water reducers are commented with the purpose of also providing a high performance concrete. (author)

A Thermoelectric Waste-Heat-Recovery System for Portland Cement Rotary Kilns

Science.gov (United States)

Luo, Qi; Li, Peng; Cai, Lanlan; Zhou, Pingwang; Tang, Di; Zhai, Pengcheng; Zhang, Qingjie

2015-06-01

Portland cement is produced by one of the most energy-intensive industrial processes. Energy consumption in the manufacture of Portland cement is approximately 110-120 kWh ton-1. The cement rotary kiln is the crucial equipment used for cement production. Approximately 10-15% of the energy consumed in production of the cement clinker is directly dissipated into the atmosphere through the external surface of the rotary kiln. Innovative technology for energy conservation is urgently needed by the cement industry. In this paper we propose a novel thermoelectric waste-heat-recovery system to reduce heat losses from cement rotary kilns. This system is configured as an array of thermoelectric generation units arranged longitudinally on a secondary shell coaxial with the rotary kiln. A mathematical model was developed for estimation of the performance of waste heat recovery. Discussions mainly focus on electricity generation and energy saving, taking a Φ4.8 × 72 m cement rotary kiln as an example. Results show that the Bi2Te3-PbTe hybrid thermoelectric waste-heat-recovery system can generate approximately 211 kW electrical power while saving 3283 kW energy. Compared with the kiln without the thermoelectric recovery system, the kiln with the system can recover more than 32.85% of the energy that used to be lost as waste heat through the kiln surface.

Influence of bismuth oxide concentration on the pH level and biocompatibility of white Portland cement

Directory of Open Access Journals (Sweden)

Marina Angélica MARCIANO

2014-07-01

Full Text Available Objectives: To investigate if there is a relation between the increase of bismuth oxide and the decrease of pH levels and an intensification of toxicity in the Portland cement. Material and Methods: White Portland cement (WPC was mixed with 0, 15, 20, 30 and 50% bismuth oxide, in weight. For the pH level test, polyethylene tubes were filled with the cements and immersed in Milli-Q water for 15, 30 and 60 days. After each period, the increase of the pH level was assessed. For the biocompatibility, two polyethylene tubes filled with the cements were implanted in ninety albino rats (n=6. The analysis of the intensity of the inflammatory infiltrate was performed after 15, 30 and 60 days. The statistical analysis was performed using the Kruskal-Wallis, Dunn and Friedman tests for the pH level and the Kruskal-Wallis and Dunn tests for the biological analysis (p0.05. For the inflammatory infiltrates, no significant statistical differences were found among the groups in each period (p>0.05. The 15% WPC showed a significant decrease of the inflammatory infiltrate from 15 to 30 and 60 days (p<0.05. Conclusions: The addition of bismuth oxide into Portland cement did not affect the pH level and the biological response. The concentration of 15% of bismuth oxide resulted in significant reduction in inflammatory response in comparison with the other concentrations evaluated.

Low porosity portland cement pastes based on furan polymers

International Nuclear Information System (INIS)

Darweesh, H.H.M.

2005-01-01

The effect of three different types of Furan polymers on the porosity, mechanical properties, mechanism of hydration and microstructure of Ordinary Portland cement (OPC) pastes was investigated. The results showed that mixing the OPC with Furan polymers, the standard water of consistency of the different cement pastes decreases and therefore the setting times (initial and final) are shortened. The total porosity of the hardened cement pastes decreased, while the mechanical properties improved and enhanced at all curing ages of hydration compared with those of the pure OPC pastes. The hydration process with Furan polymers proceeded according to the following decreasing order: F.ac. > F.ph. > F.alc. > OPC

Strategic Planning to Advance Equity on Campus: A Case Study at Portland State University

Science.gov (United States)

Zapata, Marisa; Percy, Stephen; Andrews, Sona

2018-01-01

Propelled by many factors, including a newly appointed Board of Trustees responsible for governance of our university, resource shortages, and enrollment swings, Portland State University embarked on a strategic planning effort in 2014 with the intent of reunifying a divided campus and creating a bold vision for moving forward in the next five…

Biomineralization ability and interaction of mineral trioxide aggregate and white portland cement with dentin in a phosphate-containing fluid.

Science.gov (United States)

Reyes-Carmona, Jessie F; Felippe, Mara S; Felippe, Wilson T

2009-05-01

Mineral trioxide aggregate (MTA) has been shown to be bioactive because of its ability to produce biologically compatible carbonated apatite. This study analyzed the interaction of MTA and white Portland cement with dentin after immersion in phosphate-buffered saline (PBS). Dentin disks with standardized cavities were filled with ProRoot MTA, MTA Branco, MTA BIO, white Portland cement + 20% bismuth oxide (PC1), or PC1 + 10% of calcium chloride (PC2) and immersed in 15 mL of PBS for 2 months. The precipitates were weighed and analyzed by scanning electron microscopy (SEM) and x-ray diffraction. The calcium ion release and pH of the solutions were monitored at 5, 15, 25, and 35 days. The samples were processed for SEM observations. Data were analyzed by using analysis of variance or Kruskall-Wallis tests. Our findings revealed the presence of amorphous calcium phosphate precipitates with different morphologies. The apatite formed by the cement-PBS system was deposited within collagen fibrils, promoting controlled mineral nucleation on dentin, observed as the formation of an interfacial layer with tag-like structures. All the cements tested were bioactive. The cements release some of their components in PBS, triggering the initial precipitation of amorphous calcium phosphates, which act as precursors during the formation of carbonated apatite. This spontaneous precipitation promotes a biomineralization process that leads to the formation of an interfacial layer with tag-like structures at the cement-dentin interface.

Biocompatibility and setting time of CPM-MTA and white Portland cement clinker with or without calcium sulfate.

Science.gov (United States)

Bramante, Clovis Monteiro; Kato, Marcia Magro; Assis, Gerson Francisco de; Duarte, Marco Antonio Hungaro; Bernardineli, Norberti; Moraes, Ivaldo Gomes de; Garcia, Roberto Brandão; Ordinola-Zapata, Ronald; Bramante, Alexandre Silva

2013-01-01

To evaluate the biocompatibility and the setting time of Portland cement clinker with or without 2% or 5% calcium sulfate and MTA-CPM. Twenty-four mice (Rattus norvegicus) received subcutaneously polyethylene tubes filled with Portland cement clinker with or without 2% or 5% calcium sulfate and MTA. After 15, 30 and 60 days of implantation, the animals were killed and specimens were prepared for microscopic analysis. For evaluation of the setting time, each material was analyzed using Gilmore needles weighing 113.5 g and 456.5 g, according to the ASTM specification Number C266-08 guideline. Data were analyzed by ANOVA and Tukey's test for setting time and Kruskal-Wallis and Dunn test for biocompatibility at 5% significance level. Histologic observation showed no statistically significant difference of biocompatibility (p>0.05) among the materials in the subcutaneous tissues. For the setting time, clinker without calcium sulfate showed the shortest initial and final setting times (6.18 s/21.48 s), followed by clinker with 2% calcium sulfate (9.22 s/25.33 s), clinker with 5% calcium sulfate (10.06 s/42.46 s) and MTA (15.01 s/42.46 s). All the tested materials showed biocompatibility and the calcium sulfate absence shortened the initial and final setting times of the white Portland cement clinker.

Comparative study of physico-chemical properties of MTA-based and Portland cements.

Science.gov (United States)

Borges, Alvaro H; Pedro, Fábio L M; Miranda, Carlos E S; Semenoff-Segundo, Alex; Pécora, Jesus D; Filho, Antônio M Cruz

2010-01-01

The purpose of this investigation was to evaluate the physicochemical properties of gray and white structural and nonstructural Portland cement, gray and white ProRoot MTA and MTA BIO. The water/powder ratio, setting time, solubility and pH (hydrogen-ion potential) changes of the materials were evaluated. Tests followed specification #57 from the American National Standard Institute/American Dental Association (2000) for endodontic sealing materials and pH was determined by a digital pH meter. The test results were statistically analyzed by variance analyses for global comparison and by the complementary Tukey's test for pairwise comparisons (5%). Considering the water/powder ratio, no significant difference (p > 0.05) was observed among the cements. MTA BIO (33.10 +/- 2.30) had the lowest setting time (p Portland cement (2.55 +/- 0.08) had the highest solubility (p 0.05) was observed among materials when considering pH evaluation. The pH levels were highly alkaline immediately after immersion in solution, remaining stable throughout the test period. The authors conclude that the cements had similar water/powder proportions. MTA BIO had the shortest setting time and gray ProRoot MTA had the lowest solubility. All cements had similar behavior in the pH analysis.

Science in the Eyes of Preschool Children: Findings from an Innovative Research Tool

Science.gov (United States)

Dubosarsky, Mia D.

How do young children view science? Do these views reflect cultural stereotypes? When do these views develop? These fundamental questions in the field of science education have rarely been studied with the population of preschool children. One main reason is the lack of an appropriate research instrument that addresses preschool children's developmental competencies. Extensive body of research has pointed at the significance of early childhood experiences in developing positive attitudes and interests toward learning in general and the learning of science in particular. Theoretical and empirical research suggests that stereotypical views of science may be replaced by authentic views following inquiry science experience. However, no preschool science intervention program could be designed without a reliable instrument that provides baseline information about preschool children's current views of science. The current study presents preschool children's views of science as gathered from a pioneering research tool. This tool, in the form of a computer "game," does not require reading, writing, or expressive language skills and is operated by the children. The program engages children in several simple tasks involving picture recognition and yes/no answers in order to reveal their views about science. The study was conducted with 120 preschool children in two phases and found that by the age of 4 years, participants possess an emergent concept of science. Gender and school differences were detected. Findings from this interdisciplinary study will contribute to the fields of early childhood, science education, learning technologies, program evaluation, and early childhood curriculum development.

Elementary characterization of samples of Portland cement, natural gypsum and phosphogypsum mortars from Brazil

Energy Technology Data Exchange (ETDEWEB)

Narloch, Danielle Cristine; Paschuk, Sergei Anatolyevich; Corrêa, Janine Nicolosi; Torres, Catarina Alzira Peddis; Mazer, Wellington; Macioski, Gustavo [Universidade Tecnologica Federal do Parana (UTFPR), PR (Brazil); Lara, Alessandro [Universidade de Sao Paulo (USP), SP (Brazil). Departamento de Fisica; Casali, Juliana Machado, E-mail: janine_nicolosi@hotmail.com, E-mail: alellara@hotmail.com, E-mail: jucasali@gmail.com [Instituto Federal de Santa Catarina (IFSC), Florianópolis, SC (Brazil)

2017-07-01

Portland cement, the basic ingredient of concrete and is manufactured by crushing, milling and proportioning limestone, sand, clay, iron ore and secondary materials such as shells, chalk or marl combined with shale slate or blast furnace slag, fly ash, gypsum, phosphogypsum, and some others. Evaluating the physical and mineralogical characteristics of the cement and its chemical composition is essential to establish the quality of the product. Therefore, the objective of this work was to characterize and quantify the most common chemical elements in the samples of Brazilian Portland cement, natural gypsum, and phosphogypsum mortars by means of X-ray dispersive energy spectroscopy (EDXRF), as well as to evaluate the strength of these mortars. For analysis of the compressive strength, initially prepared samples were submitted to a destructive mechanical test. Subsequently samples were milled and compacted to form thin tablets, which were submitted to the EDXRF analysis. The qualitative and quantitative analyzes showed that for phosphogypsum mortar the largest mass fractions were found of 49.8±2.5% (Si), 24.66±0.96% (S) and 22.10±0.42% (Ca). For gypsum mortar those values were found of 43.41±0.45% (Ca), 33.8 ± 0.8% (S) and 18.9±1.2% (Si), respectively; and for Portland cement mortar, the predominant elements in those samples have the mass fractions of 64.20±0.52% (Ca) and 27.3±1.5% (Si). The results showed that obtained values of mass fraction of the elements Si, S, K, Ca, Ti, Fe are in rather good agreement with quantities indicated for manufacture. Besides, gypsum and phosphogypsum presented almost the same composition and compressive strength. (author)

Elementary characterization of samples of Portland cement, natural gypsum and phosphogypsum mortars from Brazil

International Nuclear Information System (INIS)

Narloch, Danielle Cristine; Paschuk, Sergei Anatolyevich; Corrêa, Janine Nicolosi; Torres, Catarina Alzira Peddis; Mazer, Wellington; Macioski, Gustavo; Lara, Alessandro

2017-01-01

Portland cement, the basic ingredient of concrete and is manufactured by crushing, milling and proportioning limestone, sand, clay, iron ore and secondary materials such as shells, chalk or marl combined with shale slate or blast furnace slag, fly ash, gypsum, phosphogypsum, and some others. Evaluating the physical and mineralogical characteristics of the cement and its chemical composition is essential to establish the quality of the product. Therefore, the objective of this work was to characterize and quantify the most common chemical elements in the samples of Brazilian Portland cement, natural gypsum, and phosphogypsum mortars by means of X-ray dispersive energy spectroscopy (EDXRF), as well as to evaluate the strength of these mortars. For analysis of the compressive strength, initially prepared samples were submitted to a destructive mechanical test. Subsequently samples were milled and compacted to form thin tablets, which were submitted to the EDXRF analysis. The qualitative and quantitative analyzes showed that for phosphogypsum mortar the largest mass fractions were found of 49.8±2.5% (Si), 24.66±0.96% (S) and 22.10±0.42% (Ca). For gypsum mortar those values were found of 43.41±0.45% (Ca), 33.8 ± 0.8% (S) and 18.9±1.2% (Si), respectively; and for Portland cement mortar, the predominant elements in those samples have the mass fractions of 64.20±0.52% (Ca) and 27.3±1.5% (Si). The results showed that obtained values of mass fraction of the elements Si, S, K, Ca, Ti, Fe are in rather good agreement with quantities indicated for manufacture. Besides, gypsum and phosphogypsum presented almost the same composition and compressive strength. (author)

Effect of addition of opaline siliceous rocks at different proportions to portland cement

Directory of Open Access Journals (Sweden)

de Luxan, M. P.

1989-03-01

Full Text Available En este trabajo se estudia la influencia de la presencia de rocas silíceas opalinas, procedentes de las provincias de Salamanca, Zamora y Avila, en las propiedades de los cementos mixtos fabricados con cemento portland y proporciones variables de estas rocas utilizadas como adiciones activas. La caracterización de estos materiales y el estudio de las propiedades de los cementos preparados revelan la capacidad puzolánica de las rocas opalinas, y su singularidad respecto a otras puzolanas naturales, así como su posibilidad de empleo en la fabricación de cementos con adiciones.

En este trabajo se estudia la influencia de la presencia de rocas silíceas opalinas, procedentes de las provincias de Salamanca, Zamora y Avila, en las propiedades de los cementos mixtos fabricados con cemento portland y proporciones variables de estas rocas utilizadas como adiciones activas. La caracterización de estos materiales y el estudio de las propiedades de los cementos preparados revelan la capacidad puzolánica de las rocas opalinas, y su singularidad respecto a otras puzolanas naturales, así como su posibilidad de empleo en la fabricación de cementos con adiciones.

Food mirages: geographic and economic barriers to healthful food access in Portland, Oregon.

Science.gov (United States)

Breyer, Betsy; Voss-Andreae, Adriana

2013-11-01

This paper investigated the role of grocery store prices in structuring food access for low-income households in Portland, Oregon. We conducted a detailed healthful foods market basket survey and developed an index of store cost based on the USDA Thrifty Food Plan. Using this index, we estimated the difference in street-network distance between the nearest low-cost grocery store and the nearest grocery store irrespective of cost. Spatial regression of this metric in relation to income, poverty, and gentrification at the census tract scale lead to a new theory regarding food access in the urban landscape. Food deserts are sparse in Portland, but food mirages are abundant, particularly in gentrifying areas where poverty remains high. In a food mirage, grocery stores are plentiful but prices are beyond the means of low-income households, making them functionally equivalent to food deserts in that a long journey to obtain affordable, nutritious food is required in either case. Results suggested that evaluation of food environments should, at a minimum, consider both proximity and price in assessing healthy food access for low-income households. © 2013 Elsevier Ltd. All rights reserved.

Evaluation of the use of red mud as a pozzolanic additive in Portland cement

International Nuclear Information System (INIS)

Fortes, Gustavo Mattos; Balbino, Thiago Gabriel Ferreira; Lourenco, Rafaela Roberta; Rodrigues, Jose de Anchieta

2011-01-01

It is estimated that the aluminum industry generates approximately 13.7 million tones/year of red mud (RB) in Brazil. Although, being the RB rich in Al 2 O 3 and SiO 2 and partially amorphous, a potential pozzolanic activity is suggested. Thus, this work aims to evaluate the application of 15w-% of RB, as a pozzolanic additive, to the ordinary Portland cement (CPI), simulating a pozzolanic compost Portland cement (CPII-Z). To study the pozzolanic activation of the RB, this one was added without calcination, calcinated at 400°C and at 600°C. The compressive strength was measured in mortars of CPI with additions of RB, of CPI and CPII (references), after 28 days of curing. The analysis of the apparent porosity and the characterization of the hydration products were done to complement the evaluation. The mortars with calcinated RB showed good results of mechanical strength, reaching more than 85% (45 MPa) of the CPI's strength and higher values than the CPII-Z32. (author)

Microscopic analysis of dog dental pulp after pulpotomy and pulp protection with mineral trioxide aggregate and white Portland cement Análise microscópica da polpa dental de cães após pulpotomia e proteção pulpar com agregado de trióxido mineral e cimento Portland branco

Directory of Open Access Journals (Sweden)

Renato Menezes

2004-06-01

Full Text Available Considering previous studies on the similarity between the chemical composition of the mineral trioxide aggregate and the Portland cement, the purpose of this study was to investigate the pulp response of dog's teeth after pulpotomy and direct pulp protection with MTA Angelus and white Portland cement. Thirty eight pulp remnants were protected with these materials. One hundred and twenty days after treatment, the animals were sacrificed and the specimens removed and prepared for histological analysis. Both materials demonstrated the same results when used as pulp capping materials, inducing hard tissue bridge formation and maintaining pulp vitality in all specimens. The MTA Angelus and the white Portland cement showed to be effective as pulp protection materials following pulpotomy.Considerando estudos anteriores sobre a similaridade entre a composição química do agregado de trióxido mineral e o cimento Portland, o objetivo deste estudo foi investigar a resposta pulpar de dentes de cães após pulpotomia e proteção pulpar direta com MTA Angelus e cimento Portland branco. Trinta e oito remanescentes pulpares foram recobertos com esses materiais. Cento e vinte dias após o tratamento, os animais foram sacrificados e os espécimes removidos e preparados para análise histológica. Ambos os materiais demonstraram os mesmos resultados quando utilizados como materiais de capeamento pulpar, induzindo a formação de ponte de tecido mineralizado e mantendo a vitalidade pulpar em todos os espécimes. Ambos matérias se mostraram efetivos como protetores pulpares após pulpotomia em dentes de cães.

Residential conference on science in the use of coal

Energy Technology Data Exchange (ETDEWEB)

1958-01-01

The ''Residential Conference on Science in the Use of Coal'' was held in the Chemistry Department of the University of Sheffield on April 15-17, 1958. The proceedings have been published by the Institute of Fuel, 18 Devonshire Street, Portland Place, London, W.1, England. Sessions involved the physics and chemistry of coal, coal preparation and breakage, coal carbonization, coal and coke combustion and gasification and the reactivity of cokes and chars. Forty-three papers have been entered individually into EDB. (LTN)

The origins of American industrial success: Evidence from the US portland cement industry

OpenAIRE

Prentice, David

2008-01-01

The contributions of innovations, factor endowments and institutions to American industrialization are examined through analysing the rise of the American portland cement industry. Minerals abundance contributed in multiple ways to the spectacular rise of the industry from the 1890s. However, the results of a structural econometric analysis of entry suggests geological surveys, institutions highlighted by David and Wright, played a contributing rather than critical rol...

Waves and Particles, The Orbital Atom, Parts One and Two of an Integrated Science Sequence, Teacher's Guide, 1973 Edition.

Science.gov (United States)

Portland Project Committee, OR.

This teacher's guide includes parts one and two of the four-part third year Portland Project, a three-year integrated secondary science curriculum sequence. The Harvard Project Physics textbook is used for reading assignments for part one. Assignments relate to waves, light, electricity, magnetic fields, Faraday and the electrical age,…

DiskDetective.org: Finding Homes for Exoplanets Through Citizen Science

Science.gov (United States)

Kuchner, Marc J.

2016-01-01

The Disk Detective project is scouring the data archive from the WISE all-sky survey to find new debris disks and protoplanetary disks-the dusty dens where exoplanets form and dwell. Volunteers on this citizen science website have already performed 1.6 million classifications, searching a catalog 8x the size of any published WISE survey. We follow up candidates using ground based telescopes in California, Arizona, Chile, Hawaii, and Argentina. We ultimately expect to increase the pool of known debris disks by approx. 400 and triple the solid angle in clusters of young stars examined with WISE, providing a unique new catalog of isolated disk stars, key planet-search targets, and candidate advanced extraterrestrial civilizations. Come to this talk to hear the news about our latest dusty discoveries and the trials and the ecstasy of launching a new citizen science project. Please bring your laptop or smartphone if you like!

"Individualized Science" Field Test Findings and Recommendations, the Hooke Unit. Appendix A.

Science.gov (United States)

Loue, William E., III

This informal report contains the findings and recommendations resulting from the field test of the Hooke Unit of the "Individualized Science" program. Data were collected from three schools. Because of an unusual number of weaknesses ranging from formal inconsistencies to manipulative deficiencies, it was concluded that the Hooke Unit is somewhat…

Early hydration of portland cement with crystalline mineral additions

International Nuclear Information System (INIS)

Rahhal, V.; Talero, R.

2005-01-01

This research presents the effects of finely divided crystalline mineral additions (quartz and limestone), commonly known as filler, on the early hydration of portland cements with very different mineralogical composition. The used techniques to study the early hydration of blended cements were conduction calorimeter, hydraulicity (Fratini's test), non-evaporable water and X-ray diffraction. Results showed that the stimulation and the dilution effects increase when the percentage of crystalline mineral additions used is increased. Depending on the replacement proportion, the mineralogical cement composition and the type of crystalline addition, at 2 days, the prevalence of the dilution effect or the stimulation effect shows that crystalline mineral additions could act as sites of heat dissipation or heat stimulation, respectively

Rat subcutaneous tissue response to MTA Fillapex® and Portland cement.

Science.gov (United States)

Marques, Nádia Carolina Teixeira; Lourenço Neto, Natalino; Fernandes, Ana Paula; Rodini, Camila de Oliveira; Duarte, Marco Antônio Hungaro; Oliveira, Thais Marchini

2013-01-01

The aim of this study was to evaluate the response of rat subcutaneous tissue to MTA Fillapex® (Angelus), an experimental root canal filling material based on Portland cement and propylene glycol (PCPG), and a zinc oxide, eugenol and iodoform (ZOEI) paste. These materials were placed in polyethylene tubes and implanted into the dorsal connective tissue of Wistar rats for 7 and 15 days. The specimens were stained with hematoxylin and eosin, and evaluated regarding inflammatory reaction parameters by optical microscopy. The intensity of inflammatory response against the sealers was analyzed by two blinded and previously calibrated examiners for all experimental periods (kappa=0.96). The histological evaluation showed that all materials caused a moderate inflammatory reaction at 7 days, which subsided with time. A greater inflammatory reaction was observed at 7 days in the tubes filled with ZOEI paste. Tubes filled with MTA Fillapex presented some giant cells, macrophages and lymphocytes after 7 days. At 15 days, the presence of fibroblasts and collagen fibers was observed indicating normal tissue healing. The tubes filled with PCPG showed similar results to those observed in MTA Fillapex. At 15 days, the inflammatory reaction was almost absent at the tissue, with several collagen fibers indicating normal tissue healing. Data were analyzed by the nonparametric Kruskal-Wallis test (α=0.05). Statistically significant difference (p0.05). MTA Fillapex and Portland cement added with propylene glycol had greater tissue compatibility than the PCPG paste.

The regulation of hazardous air pollutants under the Clean Air Act Amendments of 1990: Effects on the Portland cement industry

International Nuclear Information System (INIS)

Mikols, E.H.; Gill, A.S.; Dougherty, A.

1996-01-01

Title III of the 1990 Clean Air Act Amendments (CAAA) addresses the control of hazardous air pollutants (HAPs) from major sources of air pollution in the US. In the CAAA, Congress defined 189 compounds as hazardous air pollutants in need of additional control by the Environmental Protection Agency (EPA). Congress directed EPA to identify the major source categories which emit HAPs and to prepare regulations that would reduce and control future HAP emissions. This paper outlines the activities undertaken by EPA to regulate HAP emissions from Portland cement plants and the program developed by the Portland cement manufacturing industry to cope with Title III

Effect of the use nickeliferous laterite and pumice as additives in the performance and durability of the Portland cement

Directory of Open Access Journals (Sweden)

María Carolina Rueda-Gualdrón

2016-01-01

Full Text Available En este trabajo se evalúa el comportamiento puzolánico de la laterita niquelífera de Cerromatoso (Córdoba y la pumita de Cemex (Boyacá en la preparación de morteros según normas NTC para agregados finos. Los morteros se prepararon con adiciones de 2,5%, 5% y 10% como sustitutos del cemento Portland tipo I, los cuales fueron sometidos a ensayos de resistencia mecánica antes y después de ser sometidos a ambientes extremos (altas temperaturas y ataques químicos como H2 SO4 y MgSO4 . Los resultados demuestran cómo estos materiales alternativos incrementan o disminuyen su grado de puzolanidad, así como el efecto de estos aditivos al interior de las mezclas de mortero en el tiempo, demostrando propiedades similares con relación a los morteros preparados con cemento Portland tipo I. Por lo tanto, los morteros tienen una respuesta aceptable ante las condiciones evaluadas, aunque es posible mejorar su desempeño y durabilidad, colaborando no solo con el ahorro energético en la producción del cemento Portland tipo I sino también en el uso de aditivos alternativos que permitan mitigar el impacto ambiental provocado por la industria cementera.

Comparative evaluation of antimicrobial activity of three cements: new endodontic cement (NEC), mineral trioxide aggregate (MTA) and Portland.

Science.gov (United States)

Hasan Zarrabi, Mohammad; Javidi, Maryam; Naderinasab, Mahboube; Gharechahi, Maryam

2009-09-01

Using the agar diffusion method, we conducted an in vitro study to evaluate the antimicrobial activity of mineral trioxide aggregate (MTA), new endodontic cement (NEC) and Portland cement at different concentrations against five different microorganisms. A base layer was made using Muller-Hinton agar for Escherichia coli (ATCC 10538) and Candida (ATCC 10231). For Actinomyces viscosus (ATCC 15987), Enterococcus faecalis (ATCC 10541) and Streptococcus mutans (ATCC 25175) blood agar medium was used. Wells were formed by removing the agar, and the materials were placed in the well immediately after manipulation. The plates were kept at room temperature for 2 h for prediffusion, and then incubated at 37 degrees C for 72 h. The inhibition zones were then measured. The data were analyzed using ANOVA and the Tukey test to compare the differences among the three cements at different concentrations. The positive controls showed bacterial growth, while the negative controls showed no bacterial growth. All materials showed antimicrobial activity against the tested strains except for Enterococcus faecalis. NEC created larger inhibition zones than MTA and Portland cement. This difference was significant for Portland cement (P 0.05). Among the examined microorganisms, the largest inhibition zone was observed for Actinomyces group (P < 0.05). The antimicrobial activity of the materials increased with time and concentration (P < 0.05). It was concluded that NEC is a potent inhibitor of microorganism growth.

National Emission Standards for Hazardous Air Pollutants (NESHAP) for the Portland Cement Manufacturing Industry Subpart LLL Rule Guidance

Science.gov (United States)

This Spring 2016 document is intended for the use of EPA staff, State and Local regulatory agencies and their staff, and industry plant managers for the NESHAP for the Portland Cement Manufacturing Industry.

Incorporation of phosphorus guest ions in the calcium silicate phases of Portland cement from 31P MAS NMR spectroscopy.

Science.gov (United States)

Poulsen, Søren L; Jakobsen, Hans J; Skibsted, Jørgen

2010-06-21

Portland cements may contain small quantities of phosphorus (typically below 0.5 wt % P(2)O(5)), originating from either the raw materials or alternative sources of fuel used to heat the cement kilns. This work reports the first (31)P MAS NMR study of anhydrous and hydrated Portland cements that focuses on the phase and site preferences of the (PO(4))(3-) guest ions in the main clinker phases and hydration products. The observed (31)P chemical shifts (10 to -2 ppm), the (31)P chemical shift anisotropy, and the resemblance of the lineshapes in the (31)P and (29)Si MAS NMR spectra strongly suggest that (PO(4))(3-) units are incorporated in the calcium silicate phases, alite (Ca(3)SiO(5)) and belite (Ca(2)SiO(4)), by substitution for (SiO(4))(4-) tetrahedra. This assignment is further supported by a determination of the spin-lattice relaxation times for (31)P in alite and belite, which exhibit the same ratio as observed for the corresponding (29)Si relaxation times. From simulations of the intensities, observed in inversion-recovery spectra for a white Portland cement, it is deduced that 1.3% and 2.1% of the Si sites in alite and belite, respectively, are replaced by phosphorus. Charge balance may potentially be achieved to some extent by a coupled substitution mechanism where Ca(2+) is replaced by Fe(3+) ions, which may account for the interaction of the (31)P spins with paramagnetic Fe(3+) ions as observed for the ordinary Portland cements. A minor fraction of phosphorus may also be present in the separate phase Ca(3)(PO(4))(2), as indicated by the observation of a narrow resonance at delta((31)P) = 3.0 ppm for two of the studied cements. (31)P{(1)H} CP/MAS NMR spectra following the hydration of a white Portland cement show that the resonances from the hydrous phosphate species fall in the same spectral range as observed for (PO(4))(3-) incorporated in alite. This similarity and the absence of a large (31)P chemical shift ansitropy indicate that the hydrous (PO(4

Temperature Characteristics of Porous Portland Cement Concrete during the Hot Summer Session

Directory of Open Access Journals (Sweden)

Liqun Hu

2017-01-01

Full Text Available Pavement heats the near-surface air and affects the thermal comfort of the human body in hot summer. Because of a large amount of connected porosity of porous Portland cement concrete (PPCC, the thermal parameters of PPCC are much different from those of traditional Portland cement concrete (PCC. The temperature change characteristics of PPCC and the effects on surrounding environment are also different. A continuous 48-hour log of temperature of a PCC and five kinds of PPCC with different porosity were recorded in the open air in the hot summer. The air temperatures at different heights above concrete specimens were tested using self-made enclosed boxes to analyze the characteristics of near-surface air temperature. The output heat flux of different concrete specimens was calculated. The results show that the PPCC has higher temperature in the daytime and lower temperature in the nighttime and larger temperature gradient than the PCC. The air temperature above PPCC is lower than that of PCC after solar radiation going to zero at night. The total output heat flux of PPCC is slightly smaller in the daytime and significantly smaller at night than that of PCC. The results of tests and calculations indicate that PPCC contributes to the mitigation of heating effect of pavement on the near-surface air.

Low-cost computer classification of land cover in the Portland area, Oregon, by signature extension techniques

Science.gov (United States)

Gaydos, Leonard

1978-01-01

Computer-aided techniques for interpreting multispectral data acquired by Landsat offer economies in the mapping of land cover. Even so, the actual establishment of the statistical classes, or "signatures," is one of the relatively more costly operations involved. Analysts have therefore been seeking cost-saving signature extension techniques that would accept training data acquired for one time or place and apply them to another. Opportunities to extend signatures occur in preprocessing steps and in the classification steps that follow. In the present example, land cover classes were derived by the simplest and most direct form of signature extension: Classes statistically derived from a Landsat scene for the Puget Sound area, Wash., were applied to the Portland area, Oreg., using data for the next Landsat scene acquired less than 25 seconds down orbit. Many features can be recognized on the reduced-scale version of the Portland land cover map shown in this report, although no statistical assessment of its accuracy is available.

Effect of ProRoot MTA, Portland cement, and amalgam on the expression of fibronectin, collagen I, and TGFβ by human periodontal ligament fibroblasts in vitro.

Science.gov (United States)

Fayazi, Sara; Ostad, Seyed Nasser; Razmi, Hasan

2011-01-01

Today many materials have been introduced for root-end filling materials. One of them is mineral trioxide aggregate (MTA) that is mentioned as a gold standard. The purpose of this in vitro study was to evaluate the reaction of human periodontal ligament fibroblasts to the root-end filling materials, such as ProRoot MTA, Portland cement, and amalgam. Eight impacted teeth were extracted in aseptic condition. The tissues around the roots were used to obtain fibroblast cells. After cell proliferation, they were cultured in the chamber slides and the extracts of the materials were added to the wells. Immunocytochemical method for measuring the expression of Fibronectin, collagen I and transforming growth factor beta (TGF®) was performed by Olysia Bioreport Imaging Software. The results were analyzed by SPSS 13.0 and Tukey post hoc test with PPortland cement group showed the most expression of collagen significantly and after 1 week, Portland cement and MTA groups had the most expression of collagen but there was no significant difference between these 2 groups. After 1 week, the Portland cement group demonstrated a higher amount of TGF® and fibronectin. The results suggest that Portland cement can be used as a less expensive root filling material with low toxicity. It has better effects than amalgam on the fibroblasts.

The Influence of Diatomite on the Strength and Microstructure of Portland Cement

OpenAIRE

Liu Jun; Shao Peng; Wang Shihao

2016-01-01

To study the influence of the types and mixing amount of diatomite on the Portland cement, we prepared the cement specimen doped with the calcined first-grade, first-grade and second-grade diatomite ,tested the 3d, 7d, 14d compressive strength, and studied and discussed phase, structure and morphology of diatomite in the binary system by the method of XRD, SEM . Experimental results show that with the addition of diatomite, the strength of cement paste increase; the optimal contents of calcin...

Effect of silica fume on reaction products of uranium (VI) with portland cement

International Nuclear Information System (INIS)

Tan Hongbin; Shaanxi Univ. of Technology, Hanzhong; Li Yuxiang

2005-01-01

Simulation of radioactive waste of U(VI) by uranyl nitrate and the effects of different additive quantities (12%, 20%, 30%, 35%, 40%) of silica fume on the products of U(VI) with Portland cement were studied at a hydrothermal condition of 180 degree C for a duration of one week. The X-ray powder diffraction examination results showed that the calcium uranate would be transformed into uranophane when the cement contained 30% silica fume. (authors)

Radon in homes of the Portland, Oregon Area: Radon data from local radon testing companies collected by CRM (Continuous Radon Measurement) machines

Science.gov (United States)

Whitney, H.; Lindsey, K.; Linde, T.; Burns, S. F.

2013-12-01

Students from the Department of Geology at Portland State University paired up with the Oregon Health Authority to better understand radon gas values in homes of the Portland metropolitan area. This study focuses on radon values collected by continuous radon measurement (CRM) machines, taken by local radon testing companies. The local companies participating in this study include Alpha Environmental Services, Inc., Cascade Radon, Environmental Works, The House Detectives, LLC, and Soil Solutions Environmental Services, Inc. In total, 2491 radon readings spanning across 77 zip codes were collected from local companies in the Portland metropolitan area. The maximum value, average value, percentage of homes greater than 4 pCi/L and total rank sum was calculated and used to determine the overall radon potential for each zip code (Burns et al., 1998). A list and four maps were produced showing the results from each category. Out of the total records, 24 zip codes resulted in high radon potential and the average reading for the entire Portland Metropolitan area was 3.7 pCi/L. High potential zip codes are thought to be a result of sand and gravel (Missoula Flood deposits) and faults present in the subsurface. The CRM data was compared with both long-term and short-term data provided by the Oregon Health Authority to validate radon potentials in each zip code. If a home is located in a zip code with high or moderate radon potential across two types of data sets, it is recommended that those homes be tested for radon gas.

The Portland Basin: A (big) river runs through it

Science.gov (United States)

Evarts, Russell C.; O'Connor, Jim E.; Wells, Ray E.; Madin, Ian P.

2009-01-01

Metropolitan Portland, Oregon, USA, lies within a small Neogene to Holocene basin in the forearc of the Cascadia subduction system. Although the basin owes its existence and structural development to its convergent-margin tectonic setting, the stratigraphic architecture of basin-fill deposits chiefly reflects its physiographic position along the lower reaches of the continental-scale Columbia River system. As a result of this globally unique setting, the basin preserves a complex record of aggradation and incision in response to distant as well as local tectonic, volcanic, and climatic events. Voluminous flood basalts, continental and locally derived sediment and volcanic debris, and catastrophic flood deposits all accumulated in an area influenced by contemporaneous tectonic deformation and variations in regional and local base level.

Optimization of superplasticizer in portland pozzolana cement mortar and concrete

Science.gov (United States)

Sathyan, Dhanya; Anand, K. B.; Mini, K. M.; Aparna, S.

2018-02-01

Chemical Admixtures are added to concrete at the time of mixing of its constituents to impart workability. The requirement of right workability is the essence of good concrete. It has been found that the use of optimum use of admixtures is very important since low dosage may result in loss of fluidity and over dosage could lead to segregation, bleeding, excessive air entrainment etc in concrete. Hence it is essential to find optimum dosage of superplasticizer for getting good strength and workability. But large number of trial tests are required in the field to find the saturation dosage of superplasticizer in concrete which requires more materials and consume more time. The paper deals with developing a co-relation between the quantity requirements of superplasticiser in mortar to that of cement concrete to get good workability. In this work for preparing mortar and concrete 4 brands of locally available Portland pozzolana cement (PPC) and superplasticizer (SP) belonging to 4 different families namely Polycarboxylate Ether (PCE), Lignosulphate (LS), Sulfonated Naphthalene Formaldehyde (SNF) and Sulfonated Melamine Formaldehyde (SMF) are used. Two different brands of SP’s are taken from each family. Workability study on the superplasticized mortar with cement to sand ratio 1:1.5 and water cement ratio of 0.4 was performed using marsh cone and flow table test and workability study on the concrete with same cement/sand ratio and water cement ratio was done using slump cone and flow table test. Saturation dosage of superplasticizer in mortar and concrete determined experimentally was compared to study the correlation between two. Compressive strength study on concrete cubes were done on concrete mixes with a superplasticizer dosage corresponding to the saturation dosage and a comparative study were done to analyse the improvement in the compressive strength with addition of superplasticizer from different family.

The Role of Authentic Objects in Museums of the History of Science and Technology: Findings from a Visitor Study

Science.gov (United States)

Hampp, Constanze; Schwan, Stephan

2015-01-01

One characteristic of science centers and science museums is that they communicate scientific findings by presenting real scientific objects. In particular, science museums focus on the historical context of scientific discoveries by displaying authentic objects, defined as original objects that once served a science-related, real-world purpose…

33 CFR 165.1315 - Safety Zones: Fireworks displays in the Captain of the Port Portland Zone.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Safety Zones: Fireworks displays... Coast Guard District § 165.1315 Safety Zones: Fireworks displays in the Captain of the Port Portland Zone. (a) Safety zones. The following areas are designated safety zones: (1) Cinco de Mayo Fireworks...

A new aluminium-hydrate species in hydrated Portland cements characterized by 27Al and 29Si MAS NMR spectroscopy

International Nuclear Information System (INIS)

Andersen, Morten Daugaard; Jakobsen, Hans J.; Skibsted, Jorgen

2006-01-01

Recent 27 Al MAS NMR studies of hydrated Portland cements and calcium-silicate-hydrate (C-S-H) phases have shown a resonance from Al in octahedral coordination, which cannot be assigned to the well-known aluminate species in hydrated Portland cements. This resonance, which exhibits the isotropic chemical shift δ iso = 5.0 ppm and the quadrupole product parameter P Q = 1.2 MHz, has been characterized in detail by 27 Al MAS and 27 Al{ 1 H} CP/MAS NMR for different hydrated white Portland cements and C-S-H phases. These experiments demonstrate that the resonance originates from an amorphous or disordered aluminate hydrate which contains Al(OH) 6 3- or O x Al(OH) 6-x (3+x)- units. The formation of the new aluminate hydrate is related to the formation of C-S-H at ambient temperatures, however, it decomposes by thermal treatment at temperatures of 70-90 o C. From the experiments in this work it is proposed that the new aluminate hydrate is either an amorphous/disordered aluminate hydroxide or a calcium aluminate hydrate, produced as a separate phase or as a nanostructured surface precipitate on the C-S-H phase. Finally, the possibilities of Al 3+ for Ca 2+ substitution in the principal layers and interlayers of the C-S-H structure are discussed

Arsenic Encapsulation Using Portland Cement With Ferrous Sulfate/Lime And Terra-BondTM Technologies - Microcharacterization And Leaching Studies

Science.gov (United States)

This work reports the results of an investigation on the treatment and encapsulation of arsenic-containing materials by Portland cement with ferrous sulfate and lime (PFL) and Terra-BondTM, a commercially available patented technology. The arsenic materials treated we...

33 CFR 165.1318 - Security and Safety Zone Regulations, Large Passenger Vessel Protection, Portland, OR Captain of...

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Security and Safety Zone Regulations, Large Passenger Vessel Protection, Portland, OR Captain of the Port Zone 165.1318 Section 165.1318 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PORTS AND...

PULPOTOMIES WITH PORTLAND CEMENT IN HUMAN PRIMARY MOLARS

Science.gov (United States)

Conti, Taísa Regina; Sakai, Vivien Thiemy; Fornetti, Ana Paula Camolese; Moretti, Ana Beatriz Silveira; Oliveira, Thais Marchini; Lourenço, Natalino; Machado, Maria Aparecida Andrade Moreira; Abdo, Ruy Cesar Camargo

2009-01-01

Two clinical cases in which Portland cement (PC) was applied as a medicament after pulpotomy of mandibular primary molars in children are presented. Pulpotomy using PC was carried out in two mandibular first molars and one mandibular second molar, which were further followed-up. At the 3, 6 and 12-month follow-up appointments, clinical and radiographic examinations of the pulpotomized teeth and their periradicular area revealed that the treatments were successful in maintaining the teeth asymptomatic and preserving pulpal vitality. Additionally, the formation of a dentin bridge immediately below the PC could be observed in the three molars treated. PC may be considered as an effective alternative for primary molar pulpotomies, at least in a short-term period. Randomized clinical trials with human teeth are required in order to determine the suitability of PC before unlimited clinical use can be recommended. PMID:19148409

Celebrating 24 years of Public Outreach of Science and Engineering in Portland Oregon

Science.gov (United States)

Bristol, Terry

2012-02-01

There have been several core strategies in our highly successful 24-year Science, Technology and Society outreach program. However, the strategy for each season is also dynamic, requiring innovation and novel coalitions. As Bob Dylan put it so succinctly, ``He not busy being born is busy dying.'' Public outreach programs - as the Chautauquas of the past - should be positioned in the cultural milieu along with the opera, symphony and theatre. Support for the enterprise needs to be a broad and diverse coalition, based ideally on the creative formation of win-win relationship. You want people to see your success as their success: ``Together we can enhance the intellectual environment in ways that none of us could do alone.'' Being multi-disciplinary presents challenges but has considerable advantages. For instance, enlightened managers of established organizations recognize the value of exposing their employees to a diversity of problem solving approaches. Instead of inviting speakers for one large lecture we now invite them to be Resident Scholars for two-three days and develop a range of additional smaller public engagements. Science and engineering topics must be relevant - placed in the broader Science, Technology and Society framework. We avoid ``gee-whiz'' in favor of what stimulates reflection on who we are, where we came from, and our role in the universe. I will briefly review how we have survived and thrived and, finally, what I see as future trends and opportunities.

The influence of calcium nitrate on setting and hardening rate of Portland cement concrete at different temperatures

Science.gov (United States)

Kičaitė, A.; Pundienė, I.; Skripkiūnas, G.

2017-10-01

Calcium nitrate in mortars and concrete is used as a multifunctional additive: as set accelerator, plasticizer, long term strength enhancer and as antifreeze admixture. Used binding material and the amount of calcium nitrate, affect the characteristics of the concrete mixture and strength of hardened concrete. The setting time of the initial and the final binding at different temperatures of hardening (+ 20 °C and + 5 °C) of the pastes made of different cements (Portland cement CEM I 42.5 R and Portland limestone cement CEM II/A-LL 42.5 R) and various amounts of calcium nitrate from 1 % until 3 % were investigated. The effect of calcium nitrate on technological characteristics of concrete mixture (the consistency of the mixture, the density, and the amount of air in the mixture), on early concrete strength after 2 and 7 days, as well as on standard concrete strength after 28 days at different temperatures (at + 20 °C and + 5 °C) were analysed.

Estudo para o aproveitamento de resíduos pétreos de marmorarias, como agregados para concreto de cimento Portland

Directory of Open Access Journals (Sweden)

Fábio Conrado de Queiroz

2008-01-01

Full Text Available In this paper, it is presented a study for the utilization of marble shops waste (stone by-products as aggregate of Portland cement concrete. First, the material were separated and classified by lithologic type. After that, they were mixed in a crusher, producing the required aggregates. Several tests for technological characterization of the material were done, intending to evaluate the use of the material as aggregate. Some simulations of Portland cement concrete dosage were done with variation in fine and coarse aggregate composition, water/cement ratio and mortar percentage. The materials were submitted to uniaxial compression test at 7th, 14th and 28th days, showing similar resistances, around to 35 MPa, independent of the aggregate mix and concrete dosage.

Alternative Fuel for Portland Cement Processing

Energy Technology Data Exchange (ETDEWEB)

Schindler, Anton K; Duke, Steve R; Burch, Thomas E; Davis, Edward W; Zee, Ralph H; Bransby, David I; Hopkins, Carla; Thompson, Rutherford L; Duan, Jingran; ; Venkatasubramanian, Vignesh; Stephen, Giles

2012-06-30

The production of cement involves a combination of numerous raw materials, strictly monitored system processes, and temperatures on the order of 1500 °C. Immense quantities of fuel are required for the production of cement. Traditionally, energy from fossil fuels was solely relied upon for the production of cement. The overarching project objective is to evaluate the use of alternative fuels to lessen the dependence on non-renewable resources to produce portland cement. The key objective of using alternative fuels is to continue to produce high-quality cement while decreasing the use of non-renewable fuels and minimizing the impact on the environment. Burn characteristics and thermodynamic parameters were evaluated with a laboratory burn simulator under conditions that mimic those in the preheater where the fuels are brought into a cement plant. A drop-tube furnace and visualization method were developed that show potential for evaluating time- and space-resolved temperature distributions for fuel solid particles and liquid droplets undergoing combustion in various combustion atmospheres. Downdraft gasification has been explored as a means to extract chemical energy from poultry litter while limiting the throughput of potentially deleterious components with regards to use in firing a cement kiln. Results have shown that the clinkering is temperature independent, at least within the controllable temperature range. Limestone also had only a slight effect on the fusion when used to coat the pellets. However, limestone addition did display some promise in regards to chlorine capture, as ash analyses showed chlorine concentrations of more than four times greater in the limestone infused ash as compared to raw poultry litter. A reliable and convenient sampling procedure was developed to estimate the combustion quality of broiler litter that is the best compromise between convenience and reliability by means of statistical analysis. Multi-day trial burns were conducted

Imaging a fossil oolitic system with GPR, insights into the exposures of the Isle of Portland (UK)

Science.gov (United States)

Moreau, Julien; Hansen, Trine L.; Nielsen, Lars

2015-04-01

The Isle of Portland shows exposure of uppermost Jurassic oolitic carbonate all along its coast. The stone of Portland properties are famous as standards for concrete composition, as building material but also for sculpture. As a consequence, the Isle has been quarried intensively for hundreds of years. The regional exposure quality is very high with a potential 3D control. The site has seen generations of geologist trainees coming for field work. The Wessex Basin where the Isle is sitting contains an active petroleum system and the geologists visiting/training there use the carbonates of Portland as an analogue to equivalent Middle-East oil and gas reservoir. Surprisingly, although the site has a tremendous potential to understand the 3D architecture and the sedimentary dynamic of an oolitic system, only punctual observations of logs (1D), sometimes correlated have been published. Several studies place a shore line between the Isle and the continent striking NEE-SWW and facing towards the Channel. Facies changes are attributed to rapid sea-level variations and Walter's Law. We have collected an extensive GPR survey of the same stratigraphic interval (The Portland Freestone). With a total of 99 GPR profiles, we have produced grids on top of most of the coastal cliffs and quarry faces. We have encountered 3 main architectures: 2-m-high bars with steep clinoforms, 10s of metres-wide channels plugged with a variety of organisms and stacked aggrading bundles of multidirectional dunesets. Our dataset does not illustrate any major unconformity which could be attributed to a sharp sea-level drop. We have interpreted our sedimentary architecture to be the result of various hydrodynamic conditions associated with a mix of wave and tide influences. The Isle shows an island barrier complex which progrades into the basin but also expands laterally filling up the available space and cannibalising itself. More proximal facies are effectively observed in the north of the island

Resistance to acid attack of portland cement mortars produced with red mud as a pozzolanic additive

International Nuclear Information System (INIS)

Balbino, Thiago Gabriel Ferreira; Fortes, Gustavo Mattos; Lourenco, Rafaela Roberta; Rodrigues, Jose de Anchieta

2011-01-01

Portland cement structures are usually exposed to aggressive environments, which requires the knowledge of the performance of these materials under deleterious conditions. In this study, it was evaluated the resistance to acid attack of mortars that contain ordinary (CPI) and compost (CPII-Z) Portland cements, adding to the first red mud (RB) as a pozzolanic additive in different conditions: without calcination, calcined at 400 ° C and at 600 ° C. The specimens were subjected to HCl and H 2 SO 4 solutions, both with concentration of 1.0 Mol L -1 for 28 days, monitoring the weight loss and leached material nature by atomic emission inductively coupled plasma (ICP). The hydration products were studied by thermogravimetric analysis (TGA) and X-ray diffraction (XRD) of the hydrated cement pastes. It was observed a reduction of portlandite amount in the RB containing cement pastes, indicating a possible pozzolanic activity of the red mud. The mortars prepared with RB were more resistant to HCl, while that ones with calcined RB present a better performance in H 2 SO 4 attack. (author)

78 FR 8493 - Foreign-Trade Zone 45-Portland, OR; Notification of Proposed Production Activity; SoloPower Inc...

Science.gov (United States)

2013-02-06

...; Notification of Proposed Production Activity; SoloPower Inc. (Thin Film Photovoltaic Solar Panels); Portland... of FTZ 45. The facility is used for the production of thin film photovoltaic solar panels. Pursuant... procedures that applies to the thin film solar panels (duty-free) for the foreign status inputs noted below...

Red mud addition in the raw meal for the production of Portland cement clinker.

Science.gov (United States)

Tsakiridis, P E; Agatzini-Leonardou, S; Oustadakis, P

2004-12-10

The aim of the present research work was to investigate the possibility of adding red mud, an alkaline leaching waste, which is obtained from bauxite during the Bayer process for alumina production, in the raw meal for the production of Portland cement clinker. For that reason, two samples of raw meals were prepared: one with ordinary raw materials, as a reference sample ((PC)Ref), and another with 3.5% red mud ((PC)R/M). The effect on the reactivity of the raw mix was evaluated on the basis of the unreacted lime content in samples sintered at 1350, 1400 and 1450 degrees C. Subsequently, the clinkers were produced by sintering the two raw meals at 1450 degrees C. The results of chemical and mineralogical analyses as well as the microscopic examination showed that the use of the red mud did not affect the mineralogical characteristics of the so produced Portland cement clinker. Furthermore, both clinkers were tested by determining the grindability, setting time, compressive strength and expansibility. The hydration products were examined by XRD analysis at 2, 7, 28 and 90 days. The results of the physico-mechanical tests showed that the addition of the red mud did not negatively affect the quality of the produced cement.

The impact of zirconium oxide radiopacifier on the early hydration behaviour of white Portland cement.

Science.gov (United States)

Coleman, Nichola J; Li, Qiu

2013-01-01

Zirconium oxide has been identified as a candidate radiopacifying agent for use in Portland cement-based biomaterials. During this study, the impact of 20 wt.% zirconium oxide on the hydration and setting reactions of white Portland cement (WPC) was monitored by powder X-ray diffraction (XRD), (29)Si and (27)Al magic angle spinning nuclear magnetic resonance spectroscopy (MAS NMR), transmission electron microscopy (TEM) and Vicat apparatus. The presence of 20 wt.% zirconium oxide particles in the size-range of 0.2 to 5 μm was found to reduce the initial and final setting times of WPC from 172 to 147 min and 213 to 191 min, respectively. Zirconium oxide did not formally participate in the chemical reactions of the hydrating cement; however, the surface of the zirconium oxide particles presented heterogeneous nucleation sites for the precipitation and growth of the early C-S-H gel products which accelerated the initial setting reactions. The presence of zirconium oxide was found to have little impact on the development of the calcium (sulpho)aluminate hydrate phases. Copyright © 2012 Elsevier B.V. All rights reserved.

Mechanical characterization of Portland cement mortars containing petroleum or coal tar

Directory of Open Access Journals (Sweden)

Garcés, P.

2007-08-01

Full Text Available This article discusses experimental data on the flexural and compressive strength of Portland cement mortars containing additions or cement replacements consisting in petroleum or coal tar, by-products of the oil and coal industries. The materials studied were two coal (BACA and BACB and two petroleum (BPP and BPT tars. The results show that it is feasible to use such materials as a partial replacement for cement in mortar manufacture. This should lead to the design of a new sustainable product that will contribute to lowering the environmental impact of construction materials while at the same time opening up an avenue for the re-use of this type of industrial by-products.En este artículo se presentan datos experimentales de resistencia a flexión y a compresión de morteros de cemento Portland con adición y sustitución de breas de petróleo y de alquitrán de carbón, que son subproductos de la industria del carbón o del petróleo. Los materiales estudiados son breas de alquitrán de carbón A (BACA y B (BACB, y dos breas de petróleo (BPP y (BPT. Los datos demuestran la viabilidad del uso de estas breas en la fabricación de morteros con menores contenidos de cemento, permitiendo diseñar un nuevo material sostenible con el medio ambiente y que contribuya a reducir el impacto ambiental de los materiales de construcción, hecho que permite abrir una nueva vía de valorización de estos subproductos.

Environmental justice and factors that influence participation in tree planting programs in Portland, Oregon, U.S

Science.gov (United States)

Geoffrey H. Donovan; John Mills

2014-01-01

Many cities have policies encouraging homeowners to plant trees. For these policies to be effective, it is important to understand what motivates a homeowner’s tree-planting decision. Researchers address this question by identifying variables that influence participation in a tree-planting program in Portland, Oregon, U.S. According to the study, homeowners with street...

Evolution of porosity in a Portland cement paste studied through positron annihilation lifetime spectroscopy

International Nuclear Information System (INIS)

Consolati, G.; Quasso, F.

2003-01-01

Positron annihilation lifetime spectroscopy experiments were carried out in an ordinary Portland cement paste characterized by a water-to-cement ratio w/c=0.8, in order to monitor the porosity of the paste. It was found that ortho-positronium intensity is a suitable quantity to this purpose, being sensitive to the amount of water contained in the pores. The experimental data show good agreement with the porosity calculated according to the Powers' thin filmsodel

Petrographic Analysis of Portland Cement Concrete Cores from Pease Air National Guard Base, New Hampshire

Science.gov (United States)

2016-11-01

Petrographic Analysis of Portland Cement Concrete Cores from Pease Air National Guard Base, New Hampshire E n g in e e r R e s e a rc h a n d...id, age of the concrete being evaluated and tests performed...4 3 Preface This study was conducted in support of the Air Force Civil Engineer Center (AFCEC) to assess concrete obtained from Pease

Immobilization of citric acid solutions in portland cement

International Nuclear Information System (INIS)

Lopes, Valdir M.; Rzyski, Barbara M.

1997-01-01

Decontamination processes by using citric acid on certain items used in the nuclear area, can result in large volumes of liquid wastes with low activity or effluents, contaminated with uranium and some elements dangerous to the environment. A great number of installations that have decontamination processes adopt the zero discharge philosophy. So, one of the forms to isolate the solutions is by reducing its volume through the evaporation process. The generated must can be neutralized and encapsulated or immobilized in Portland cement. This work propose a chemical technique to destroy the citric acid in the decontamination solutions instead of neutralization and, depending on the installation convenience, a direct cement immobilization of these solutions or of the evaporation mud. The results obtained in this work involve data about the workability, setting time and mechanical resistance, after 28 days of sealed cure, for samples with water-cement ratios of 4, 0.5 and 0.6, by weight. (author). 5 refs., 2 tabs

The AFm phase in Portland cement

International Nuclear Information System (INIS)

Matschei, T.; Lothenbach, B.; Glasser, F.P.

2007-01-01

The AFm phase of Portland cements refers to a family of hydrated calcium aluminates based on the hydrocalumite-like structure of 4CaO.Al 2 O 3 .13-19 H 2 O. However OH - may be replaced by SO 4 2- and CO 3 2- . Except for limited replacement (50 mol%, maximum) of sulfate by hydroxide, these compositions do not form solid solutions and, from the mineralogical standpoint, behave as separate phases. Therefore many hydrated cements will contain mixtures of AFm phases. AFm phases have been made from precursors and experimentally-determined phase relationships are depicted at 25 deg. C. Solubility data are reported and thermodynamic data are derived. The 25 deg. C stability of AFm phases is much affected by the nature of the anion: carbonate stabilises AFm and displaces OH and SO 4 at species activities commonly encountered in cement systems. However in the presence of portlandite, and as carbonate displaces sulfate in AFm, the reaction results in changes in the amount of both portlandite and ettringite: specimen calculations are presented to quantify these changes. The scheme of phase balances enables calculation of the mineralogical balances of a hydrated cement paste with greater accuracy than hitherto practicable

Large-scale Meteorological Patterns Associated with Extreme Precipitation Events over Portland, OR

Science.gov (United States)

Aragon, C.; Loikith, P. C.; Lintner, B. R.; Pike, M.

2017-12-01

Extreme precipitation events can have profound impacts on human life and infrastructure, with broad implications across a range of stakeholders. Changes to extreme precipitation events are a projected outcome of climate change that warrants further study, especially at regional- to local-scales. While global climate models are generally capable of simulating mean climate at global-to-regional scales with reasonable skill, resiliency and adaptation decisions are made at local-scales where most state-of-the-art climate models are limited by coarse resolution. Characterization of large-scale meteorological patterns associated with extreme precipitation events at local-scales can provide climatic information without this scale limitation, thus facilitating stakeholder decision-making. This research will use synoptic climatology as a tool by which to characterize the key large-scale meteorological patterns associated with extreme precipitation events in the Portland, Oregon metro region. Composite analysis of meteorological patterns associated with extreme precipitation days, and associated watershed-specific flooding, is employed to enhance understanding of the climatic drivers behind such events. The self-organizing maps approach is then used to characterize the within-composite variability of the large-scale meteorological patterns associated with extreme precipitation events, allowing us to better understand the different types of meteorological conditions that lead to high-impact precipitation events and associated hydrologic impacts. A more comprehensive understanding of the meteorological drivers of extremes will aid in evaluation of the ability of climate models to capture key patterns associated with extreme precipitation over Portland and to better interpret projections of future climate at impact-relevant scales.

Immobilisation Of Spent Ion Exchange Resins Using Portland Cement Blending With Organic Material

International Nuclear Information System (INIS)

Zalina Laili; Mohd Abdul Wahab; Nur Azna Mahmud

2014-01-01

Immobilisation of spent ion exchange resins (spent resins) using Portland cement blending with organic material for example bio char was investigated. The performance of cement-bio char matrix for immobilisation of spent ion exchange resins was evaluated based on their compression strength and leachability under different experimental conditions. The results showed that the amount of bio char and spent resins loading effect the compressive strength of the waste form. Several factors affecting the leaching behaviour of immobilised spent resins in cement-bio char matrix. (author)

Concentration of electrolyte reserves of the juvenile african catfish clarias gariepinus (burchell, 1822) exposed to sublethal concentrations of portland cement powder in solution

International Nuclear Information System (INIS)

Adamu, M.K.; Francis, O.A.

2008-01-01

The study investigated the effect of sublethal concentrations (39.10, 19.55, 9.87 and 0.00 mg/l) of Portland cement powder in solution on the electrolyte reserves (sodium, potassium, calcium, chloride and inorganic phosphorus) in the serum, liver and kidney of the juvenile African catfish Clarias gariepinus after a 15 day exposure period. The basic function of the determined electrolyte reserves in the body lies in controlling fluid distribution, intra and extra cellular acidobasic equilibrium, maintaining osmotic pressure of body fluid and normal neuro-muscular irritability. The result revealed significant (P 0.05) changes in inorganic phosphorus. Sodium, calcium, chloride and inorganic phosphorus and potassium were significantly (P 0.05) different in liver and kidney, respectively. Ipso-facto, the effector organs viz: liver and kidney of teleost species - Clarias gariepinus which are primarily responsible for regulating water and ionic movement between external and internal milieu of fishes are susceptible to deleterious effects of Portland cement powder thus sublethal concentration (39.10 mg/l) of Portland cement powder in solution after a 15 day exposure has been most toxic and debilitating to the test fish. (author)

Finding Meaningful Roles for Scientists in science Education Reform

Science.gov (United States)

Evans, Brenda

Successful efforts to achieve reform in science education require the active and purposeful engagement of professional scientists. Working as partners with teachers, school administrators, science educators, parents, and other stakeholders, scientists can make important contributions to the improvement of science teaching and learning in pre-college classrooms. The world of a practicing university, corporate, or government scientist may seem far removed from that of students in an elementary classroom. However, the science knowledge and understanding of all future scientists and scientifically literate citizens begin with their introduction to scientific concepts and phenomena in childhood and the early grades. Science education is the responsibility of the entire scientific community and is not solely the responsibility of teachers and other professional educators. Scientists can serve many roles in science education reform including the following: (1) Science Content Resource, (2) Career Role Model, (3) Interpreter of Science (4) Validator for the Importance of Learning Science and Mathematics, (5) Champion of Real World Connections and Value of Science, (6) Experience and Access to Funding Sources, (7) Link for Community and Business Support, (8) Political Supporter. Special programs have been developed to assist scientists and engineers to be effective partners and advocates of science education reform. We will discuss the rationale, organization, and results of some of these partnership development programs.

Influence of Ba2+ and Sr2+ ions on the hydration process of portland cement and blended cements

Directory of Open Access Journals (Sweden)

Živanović, B. M.

1987-12-01

Full Text Available This study concerns the influence of the concentration of Sr2+ and Ba2+ ions in mortar batch waters upon the hydration process of various Portland and additive cements. An increase in the mechanical resistence of said cements is observed, after 28 days, when the concentration of Ba2+ and Sr2+ ions in the mortar batch waters increases. This suggests a possible microstructural explanation of said phenomenon.En el presente trabajo se estudia la influencia de la concentración de los iones Sr2+ y Ba2+ en las aguas de amasado sobre el proceso de hidratación de varios cementos portland y de adición. Se comprueba un incremento de las resistencias mecánicas de dichos cementos, a los 28 días, cuando aumenta la concentración de los iones Ba2+ y Sr2+ en las aguas de amasado, lo cual sugiere una posible explicación microestructural a dicho fenómeno.

Evolution and quantification of the main Sensitisers in commercial portland cements

Directory of Open Access Journals (Sweden)

Frías, M.

2002-03-01

Full Text Available The commercial Portland cements contain minor elements in their chemical compositions. The presence of these elements has a direct incidence in different aspects: rheological behaviour, reaction kinetics, environmental, etc. Some of them also have a negative effect on the human health; so, chromium (Cr, nickel (Ni and cobalt (Co are the main allergens present in Portland cements, causing of Professional Dermatitis in construction workers. The current study is focussed on the quantification of total and soluble chromium, nickel and cobalt in a wide range of Spanish commercial cements. These values can represent a contribution to the establishing of possible limitations or reductions of these elements in forthcoming standards. Analytical data show that clinkers are the main responsibles of the presence of soluble chromium in commercial cements. This fact could be indicating that chromium solubility (from inert Cr III to soluble Cr VI would be closely related to the clinkerisation conditions. On the other hand, there is not a direct ratio between total chromium and soluble chromium; it means that analytical results are punctual and not any case can be extrapolating ones. Ni and Co solubility in water is practically negligible either raw as clinkers.

Los cementos Portland comerciales contienen elementos minoritarios en su composición química. La presencia de estos elementos tiene una incidencia directa en diferentes aspectos: comportamiento reológico, cinética de reacción, contaminación ambiental, etc. Algunos de ellos, aparte de su incidencia mencionada anteriormente, tienen un efecto negativo en la salud humana. Así, el cromo (Cr, níquel (Ni y cobalto (Co son los principales alérgenos contenidos en los cementos y, por lo tanto, los principales causantes de la Dermatitis Profesional. Este trabajo se centra en la cuantifîcación de los contenidos totales y solubles de cromo, níquel y cobalto presentes en los cementos comerciales

"Why Is This the Only Place in Portland I See Black People?": Teaching Young Children about Redlining

Science.gov (United States)

Johnson, Katharine

2012-01-01

As in many historically black neighborhoods in the United States, the gentrification of northeast Portland rests on an older history of economic injustice perpetrated by banks, realtors, governments, and white property owners. Redlining was one piece of an elaborate puzzle denying people of color access to housing and to wealth. The term refers to…

CALCIUM ORTHOPHOSPHATES HYDRATES: FORMATION, STABILITY AND INFLUENCE ON STANDARD PROPERTIES OF PORTLAND CEMENT

Directory of Open Access Journals (Sweden)

Kaziliunas A.

2013-12-01

Full Text Available Preparation of phosphogypsum to produce the binders requires a much higher input than preparation of natural gypsum stone. This makes it uncompetitive material. The investigations presented therein are meant to reduce this input by looking for the ways of rendering impurities harmless. Soluble acid orthophosphates are the main harmful impurity of phosphogypsum. The studies show that dry insoluble calcium orthophosphates hydrates (1.09 % and 2.18 % P2O5 in gypsum have little effect on W/C, setting times and soundness of Portland cement pastes. Insoluble calcium orthophosphates hydrates {CaHPO4∙2H2O, Ca8(HPO42(PO44∙5H2O and Ca9(HPO4(PO45(OH∙4H2O} formed in acidic medium (pH = 4.2 - 5.9 have been destroyed in alkaline medium and reduce standard compressive strength of cement up to 28 %. Calcium orthophosphates hydrates of hydroxyapatite group are stable in alcaline medium, while in dry state they reduce the standard compressive strength of cement until 10 %, but their suspensions prolong setting times of Portland cement as soluble orthophosphates – 2 - 3 times. Alkalis in cement increase pH of paste, but do not change the process of formation of calcium orthophosphates hydrates of hydroxyapatite group: it takes place through an intermediate phase - CaHPO4·2H2O, whose transformation into apatite lasts for 2 - 3 months.

77 FR 39793 - Notice of Intent To Rule on Request To Release Airport Property at Portland-Hillsboro Airport...

Science.gov (United States)

2012-07-05

... To Release Airport Property at Portland--Hillsboro Airport, Hillsboro, OR AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of Proposal to Release Airport Property. SUMMARY: The FAA proposes to... provisions of Section 125 of the Wendell H. Ford Aviation Investment Reform Act for the 21st Century (AIR 21...

Estudo do reaproveitamento do cimento Portland de alta resistência inicial

Directory of Open Access Journals (Sweden)

A. G. de Araújo Jr.

Full Text Available Resumo Devido aos impactos ambientais gerados pela construção civil, muitos pesquisadores têm estudado os resíduos de construção e demolição. É possível encontrar na literatura científica trabalhos focados na pasta de cimento endurecido. Neste estudo, pasta de cimento Portland hidratada (PCH preparada a partir de cimento Portland CP V-ARI (CP-V foi desidratada via tratamento térmico a 700 °C (700-PCD e a 900 °C (900-PCD, sendo em seguida reidratada. A estrutura e microestrutura durante hidratação, desidratação e reidratação foram investigadas. Para a caracterização das mudanças morfológicas, difração de raios X, espectroscopia no infravermelho com transformada de Fourier e microscopia eletrônica de varredura foram utilizadas. A análise termogravimétrica foi utilizada para estudar as etapas de desidratação da pasta de cimento hidratada original. O estudo de desidratação da PCH mostrou que a 700 e 900 °C os novos nesossilicatos e CaO estão claramente presentes nas amostras. Durante a reidratação das amostras de 700-PCD e o 900-PCD, ocorreram reidratação parcial e carbonatação. Corpos de prova a partir de CP-V e 0%, 2%, 10%, 40% e 60% de pó de cimento desidratado (PCD foram preparados. Corpos de prova preparados com até 40% de PCD apresentaram propriedades semelhantes, quando comparado com corpos de prova de pasta de cimento puro preparados com CP-V, enquanto adições de 60% de PCD resultaram em um decréscimo da resistência à compressão.

Risk communications in nuclear energy as science and technology. Arrangement and analysis of academic findings and practical cases

International Nuclear Information System (INIS)

Toyoda, Satoshi

2006-01-01

Problems in communication among the government, enterprise, experts and so on and the society and people, now confront us in several areas of science and technology. In order to be accepted by the society, each area of science and technology has experienced common processes such as beginnings, business, society introduction, problem renovation and maturity. Each area can be positioned based on the degree of maturity, which helps to find solutions of the problems. Arrangement and analysis of academic findings and practical cases on risk communications in nuclear energy are described. (T. Tanaka)

Determination of the Apical Sealing Abilities of Mineral Trioxide Aggregate, Portland Cement, and Bioaggregate After Irrigation with Different Solutions.

Science.gov (United States)

Bayram, H Melike; Saklar, Feridun; Bayram, Emre; Orucoglu, Hasan; Bozkurt, Alperen

2015-06-01

The purpose of this study was to investigate the sealing ability of root-end filling materials such as mineral trioxide aggregate (MTA), Portland cement, and bioaggregate (BA) after irrigation with different solutions. We examined 130 human maxillar central teeth. After cutting the teeth at the cementoenamel junction, the root canals were expanded using nickel-titanium rotary instruments. Root canals were filled with AH-plus and gutta-percha. Then, the roots were cut apically, and 3 mm deep retrograde cavities were prepared. The roots were divided 12 experimental groups, consisting 10 teeth each; the positive and negative control groups contained five teeth each. The retrograde cavities were rinsed using ethylenediaminetetraacetic acid (EDTA), chlorhexidine (CHX), BioPure(™) mixture of a tetracycline isomer, an acid, and a detergent (MTAD), or distilled water. Next, groups 1, 2, 3, and 4 were sealed with MTA; groups 5, 6, 7, and 8 were sealed with Portland cement; and groups 9, 10, 11, and 12 were sealed with BA. Then, apical microleakage was evaluated by using a computerized fluid filtration method. The results of the leakage test were statistically evaluated by the post-hoc Tukey's test. MTA, Portland cement, and BA root-end filling materials showed the least leakage in the CHX and distilled water groups. The highest leakage was observed in the EDTA and MTAD groups. The sealing ability of BA was as good as that of MTA. EDTA and MTAD increased the apical leakage and CHX and distilled water decreased the leakage of the root-end filling materials examined in this study.

Oiling and cleanup issues in wetlands, M/T Julie N spill, Portland, Maine

International Nuclear Information System (INIS)

Michel, J.; Lehmann, S.M.; Henry, C.B.Jr.

1998-01-01

The clean up and environmental assessment techniques which were used following the September 1996 oil spill from the M/T Julie N in Portland Harbor, Maine were reviewed and documented. The spill resulted in heavy oiling of wetland. Aerial photography, ground-truth surveys, transects and chemical sampling were conducted to try to assess the impact to wetlands and to decide on appropriate cleanup options. A range of cleanup methods were attempted including low-pressure flushing, shoreline cleaning agents, vegetation cutting, and natural recovery. 9 refs., 3 tabs., 1 fig

The Estimation of Compaction Parameter Values Based on Soil Properties Values Stabilized with Portland Cement

Science.gov (United States)

Lubis, A. S.; Muis, Z. A.; Pasaribu, M. I.

2017-03-01

The strength and durability of pavement construction is highly dependent on the properties and subgrade bearing capacity. This then led to the idea of the selection methods to estimate the density of the soil with the proper implementation of the system, fast and economical. This study aims to estimate the compaction parameter value namely the maximum dry unit weight (γd max) and optimum moisture content (wopt) of the soil properties value that stabilized with Portland Cement. Tests conducted in the laboratory of soil mechanics to determine the index properties (fines and liquid limit) and Standard Compaction Test. Soil samples that have Plasticity Index (PI) between 0-15% then mixed with Portland Cement (PC) with variations of 2%, 4%, 6%, 8% and 10%, each 10 samples. The results showed that the maximum dry unit weight (γd max) and wopt has a significant relationship with percent fines, liquid limit and the percentation of cement. Equation for the estimated maximum dry unit weight (γd max) = 1.782 - 0.011*LL + 0,000*F + 0.006*PS with R2 = 0.915 and the estimated optimum moisture content (wopt) = 3.441 + 0.594*LL + 0,025*F + 0,024*PS with R2 = 0.726.

Assessment of diabetic teleretinal imaging program at the Portland Department of Veterans Affairs Medical Center.

Science.gov (United States)

Tsan, Grace L; Hoban, Keely L; Jun, Weon; Riedel, Kevin J; Pedersen, Amy L; Hayes, John

2015-01-01

We conducted a retrospective chart review of 200 diabetic patients who had teleretinal imaging performed between January 1, 2010, and January 1, 2011, at Portland Department of Veterans Affairs (VA) Medical Center outpatient clinics to assess the effectiveness of the diabetic teleretinal imaging program. Twenty patients (10%) had diabetic retinopathy. Ninety percent of the available teleretinal imaging studies were of adequate quality for interpretation. In accordance with local VA policy at that time, all teleretinal imaging patients should have been referred for a dilated retinal examination the following year. Image readers referred 97.5% of the patients to eye clinics for subsequent eye examinations, but the imagers scheduled appointments for only 80% of these patients. The redundancy rate, i.e., patients who had an eye examination within the past 6 mo, was 11%; the duplicate recall rate, i.e., patients who had a second teleretinal imaging performed within 1 yr of the eye examination, was 37%. Rates of timely diabetic eye examinations at clinics with teleretinal imaging programs, particularly when teleretinal imaging and eye clinics were colocated at the same community-based outpatient clinic, were higher than those without a teleretinal imaging program. We concluded that the Portland VA Medical Center's teleretinal imaging program was successful in increasing the screening rate for diabetic retinopathy.

A comparative evaluation of ProRoot mineral trioxide aggregate and Portland cement as a pulpotomy medicament.

Science.gov (United States)

Bhagat, Dipti; Sunder, Ravi Kadur; Devendrappa, Shashikiran Nandihalli; Vanka, Amit; Choudaha, Nidhi

2016-01-01

Recently, some studies have compared mineral trioxide aggregate (MTA) with portland cement (PC), concluding that the principle ingredients of PC are similar to those of MTA. The purpose of the present study was to evaluate the biocompatibility of PC as a pulpotomy medicament. Thirty premolars that scheduled for extraction for therapeutic reasons were randomly assigned to two experimental groups: ProRoot MTA (PMTA) and PC. After isolation and pulp exposure, pulpotomy was carried out and pulps were dressed with PMTA and PC. After 6 months, the teeth were extracted and prepared for histological analysis based on Cox et al. criteria. The data were analyzed by Z-test of proportion with 1% of allowed error. No statistically significant difference was found between the two groups with respect to inflammatory response, soft tissue organization, and dentine bridge formation (P > 0.05). PC was associated with similar favorable biological response to pulpotomy treatment as PMTA. The findings of this study support the idea that PC can be considered a cheaper substitute to MTA.

Tabular data base construction and analysis from thematic classified Landsat imagery of Portland, Oregon

Science.gov (United States)

Bryant, N. A.; George, A. J., Jr.; Hegdahl, R.

1977-01-01

A systematic verification of Landsat data classifications of the Portland, Oregon metropolitan area has been undertaken on the basis of census tract data. The degree of systematic misclassification due to the Bayesian classifier used to process the Landsat data was noted for the various suburban, industrialized and central business districts of the metropolitan area. The Landsat determinations of residential land use were employed to estimate the number of automobile trips generated in the region and to model air pollution hazards.

The effect of urban trees on the rental price of single-family homes in Portland, Oregon

Science.gov (United States)

Geoffrey H. Donovan; David T. Butry

2011-01-01

Few studies have estimated the effect of environmental amenities on the rental price of houses. We address this gap in the literature by quantifying the effect of urban trees on the rental price of single-family homes in Portland, Oregon, USA. We found that an additional tree on a house's lot increased monthly rent by $5.62, and a tree in the public right of way...

Effect of saliva and blood contamination on the bi-axial flexural strength and setting time of two calcium-silicate based cements: Portland cement and biodentine.

Science.gov (United States)

Alhodiry, W; Lyons, M F; Chadwick, R G

2014-03-01

This study evaluated the effect of contamination with saliva and blood on the bi-axial flexural strength and setting time of pure gray Portland cement and Biodentine (Septodont, Allington, UK). A one-way ANOVA showed that contamination caused no significant difference between the cements in bi-axial flexural strength (P> 0.05). However there was a significant difference in setting time (PPortland cement taking longer than Biodentine, regardless of the contaminant, and contamination with blood increased the setting time of both materials. Biodentine was similar in strength to Portland cement, but had a shorter setting time for both contaminated and non-contaminated samples.

Utilization of the national Portland cement for immobilizing radioactive wastes - Physical characteristics

International Nuclear Information System (INIS)

Rzyski, B.M.; Suarez, A.A.

1988-01-01

This paper shows the results obtained in the study of the national Portland cement, P320, as matrix for radioactive nitric waste incorporation. Cement use practice in other countries is common for this purposes and demonstrates to be cheap and accessible when low and medium level wastes are immobilized. Some of physical characteristics as: homogeneity,mechanical strenght, setting and porosity are analysed due to water-cement ratio and salt contents. Those characteristics which are proper of the final product, must be controlled in such way to assure a long time integrity of the wasteform. The establishment of process and quality control criteria are based in such kind of data. (author) [pt

Microstructure Development and Transport Properties of Portland Cement-fly Ash Binary Systems : In view of service life predictions

NARCIS (Netherlands)

Yu, Z.

2015-01-01

Fly ash is a by-product of burning coal in electric power generating plants. It is commonly known that owing to its pozzolanic properties fly ash is widely used as a partial replacement for Portland cement in concrete. The use of fly ash in concrete not only reduces the landfill costs of fly ash,

Perspektiven einer Rezeption neurowissenschaftlicher Erkenntnisse in der Erziehungswissenschaft (Perspectives of an Integration of Neuro-Scientific Findings into Educational Science).

Science.gov (United States)

Becker, Nicole

2002-01-01

Sketches the status quo and possible starting points for the adoption of neuro-scientific findings by educational science. Describes the latest developments in U.S. research. Discusses the adoption of these points by German educational science. Outlines the possibilities and limits of an interdisciplinary discourse. (CAJ)

Implications of Socio-Cultural Research Findings for Science ...

African Journals Online (AJOL)

As such, school systems have been asked to provide challenging and stimulating science programmes that lead to scientific literacy for all. However, despite the heavy injection of scarce funds and resources to support various science education reform programmes, evaluation studies show disappointingly, that the level of ...

Hydration of Portland cement with additions of calcium sulfoaluminates

International Nuclear Information System (INIS)

Le Saoût, Gwenn; Lothenbach, Barbara; Hori, Akihiro; Higuchi, Takayuki; Winnefeld, Frank

2013-01-01

The effect of mineral additions based on calcium aluminates on the hydration mechanism of ordinary Portland cement (OPC) was investigated using isothermal calorimetry, thermal analysis, X-ray diffraction, scanning electron microscopy, solid state nuclear magnetic resonance and pore solution analysis. Results show that the addition of a calcium sulfoaluminate cement (CSA) to the OPC does not affect the hydration mechanism of alite but controls the aluminate dissolution. In the second blend investigated, a rapid setting cement, the amorphous calcium aluminate reacts very fast to ettringite. The release of aluminum ions strongly retards the hydration of alite but the C–S–H has a similar composition as in OPC with no additional Al to Si substitution. As in CSA–OPC, the aluminate hydration is controlled by the availability of sulfates. The coupling of thermodynamic modeling with the kinetic equations predicts the amount of hydrates and pore solution compositions as a function of time and validates the model in these systems.

Reuse of a residue from petrochemical industry with portland cement Reutilización de un residuo de la industria petroquímica como adición al cemento portland

Directory of Open Access Journals (Sweden)

Janneth Torres Agredo

2012-06-01

Full Text Available In this article the possibility of using waste from the petrochemical industry,as partial replacement of Portland cement is studied, evaluating the presenceof contaminants in the waste and the encapsulation, once it is confined on the cement. This has been done, in order to find a use to this residue without cause damage to the environment. This residue, called spent fluid catalytic cracking catalyst (FCC, is mainly formed by a type Y zeolite, which is dispersing in an inorganic oxides matrix. The toxicity characteristic leaching proceeding was applied, in mortars adding with 20% of FCC as Portland cement replacement. The results showed that the residue does not represent a problem from the point of view of the leaching of elements, such as As, Pb, Zn, Cr, and La, which were below to the permissible limits. Additionally, the pozzolanic activity of FCC was evaluated according to ASTM C311, where the efficiency of the residue as pozzolanic addition is demonstrated. With the results the importance of reusing a residue of the petrochemical industry is emphasized, that decreases the amount of cement to be used and improves the mechanical resistance of the materials containing it.En el presente artículo se estudia la posibilidad de utilizar un residuo de la industria petroquímica, como sustitución parcial del cemento Portland, evaluando la presencia de elementos contaminantes en el residuo y su encapsulación, una vez se haya confinado con el cemento. Lo anterior, con el fin de determinar si su uso como material de construcción, puede o no causar un efecto negativo al medio ambiente. El residuo, denominado catalizador usado de craqueo catalítico (FCC, es un material que está compuesto por una zeolita tipo Y, dispersa en una matriz de óxidos inorgánicos. Se aplicó la técnica de TCLP (del inglés Toxicity Characteristic Leaching Procedure, en morteros adicionados con un 20%, de FCC con respecto a la cantidad de cemento. Los resultados

Clinical and Radiographic Evaluation of the Effectiveness of Formocresol, Mineral Trioxide Aggregate, Portland Cement, and Enamel Matrix Derivative in Primary Teeth Pulpotomies: A Two Year Follow-Up.

Science.gov (United States)

Yildirim, Ceren; Basak, Feridun; Akgun, Ozlem Marti; Polat, Gunseli Guven; Altun, Ceyhan

2016-01-01

The aim of this study was to evaluate and to compare clinical and radiographic outcomes of 4 materials (formocresol, mineral trioxide aggregate (MTA), Portland cement and enamel matrix derivative) using in primary teeth pulpotomies. Sixty-five patients aged 5-9 years (32 female, 33 male) were included in this study. A total of 140 primary first and second molars with deep caries were treated with pulpotomy. All teeth were then restored with stainless steel crowns. The treated teeth were evaluated clinically and radiographically at 3, 6, 12, 18 and 24 months. At 24 months, the clinical success rates of formocresol, MTA, Portland cement, and enamel matrix derivative were 96.9%, 100%, 93.9%, and 93.3%, respectively. The corresponding radiographic success rates were 84.4%, 93.9%, 86.7% and 78.1%, respectively. Although there were no statistically significant differences in clinical and radiographic success rates among the 4 groups, MTA appears to be superior to formocresol, Portland cement, and enamel matrix derivative as a pulpotomy agent in primary teeth.

Properties of SiMn slag as apozzolanic material in portland cement manufacture

Directory of Open Access Journals (Sweden)

Frías, M.

2005-12-01

Full Text Available The primary purpose of this study was to evaluate the behaviour of SiMn slag as a pozzolanic material in commercial Portland cement manufacture. This necessitated exploring different scientific and technical aspects to ensure a correct valuation. The results obtained revealed that silica and calcium are the main components of SiMn slag, whose pozzolanic activity occupies an intermediate position between silica fume and fly ash; it reduces heat of hydration and mortars made with cement containing SiMn slag exhibit compressive strength values similar to the figures for standard mortar. Consequently, the use of SiMn slag as an active addition to cement is feasible, inasmuch as the resulting product meets the requirements laid down in the present legislation.

El objetivo principal de este trabajo es evaluar el comportamiento de la escoria de SiMn como material puzolánico en la fabricación de cementos Portland comerciales. Para ello, resulta necesario investigar diferentes aspectos científicos y técnicos que conlleven a una correcta valorización de las mismas. Los resultados obtenidos en el presente trabajo han puesto de manifiesto que la escoria de SiMn presenta una naturaleza sílico-cálcica, actividad puzolúnica intermedia entre el humo de sílice y ceniza volante, reduce el calor de hidratación y los morteros con escoria de SiMn muestra alcanzan resistencias a compresión similares a las del mortero patrón. Por lo tanto, la utilización de la escoria de SiMn como adición activa al cemento es viable, cumpliendo con las exigencias recogidas en la norma vigente.

Immobilisation of strontium, nickel and iodide by a sulphate-resisting Portland cement

International Nuclear Information System (INIS)

Wieland, E.; Tits, J.; Spieler, P.; Dobler, J.-P.

1998-01-01

The interaction of Sr(II), Ni(II) and I(-I) with sulphate-resisting Portland cement was investigated under highly alkaline conditions. Batch-sorption studies were performed by contacting HTS cement (haute teneur en silice, sulphate-resisting Portland cement, Lafarge, France) with artificial cement pore water (ACW). The composition of ACW was 0.18 M KOH, 0.114 M NaOH and 1.2 mM Ca(OH) 2 . 85 Sr, 63 Ni and 125 I were used as tracers. In the experiments with Sr(II) and Ni(II), isosaccharinic acid (ISA) was added to ACW at 10 -5 M to 10 -2 M in order to study the effect of complexing ligands on radionuclide retention. The stability of the tracer solutions and the cement suspensions were first assessed. Moreover, the inventory of the stable elements were determined in cement and cement pore water. We then studied the kinetics of the radionuclide-cement interaction process and measured the dependence of the distribution ratio (R d ) on the concentration of ISA and on the concentration of cement particles (S:L ratio). In the case of 63 Ni and 125 I a strong decrease in the distribution ratio (R d ) with increasing S:L ratio was observed. There is strong indication that the inventory of the stable fraction of an element present in cement pore water accounts for the retention of the radioisotope fraction. The results further indicate that phase transformations may occur in non-pre-equilibrated cement systems (non-equilibrium conditions) which affect 63 Ni uptake by HTS cement. The distribution ratios measured on HTS cement were compared with values obtained from measurements on important cement components (portlandite, CSH/C(A)SH-phases)

Industrial Wastes as Alternative Mineral Addition in Portland Cement and as Aggregate in Coating Mortars

OpenAIRE

Oliveira, Kamilla Almeida; Nazário, Bruna Inácio; Oliveira, Antonio Pedro Novaes de; Hotza, Dachamir; Raupp-Pereira, Fabiano

2017-01-01

This paper presents an evaluation study of wastes from pulp and paper as well as construction and demolition industries for application in cement-based materials. The alternative raw materials were used as a source of calcium carbonate (CaCO3) and as pozzolanic material (water-reactive SiO2) in partial replacement of Portland cement. In addition to the hydraulic binder, coating mortars were composed by combining the pulp and paper fluidized bed sand residue with construction and demolition wa...

Solidification of ion exchange resins saturated with Na+ ions: Comparison of matrices based on Portland and blast furnace slag cement

Science.gov (United States)

Lafond, E.; Cau dit Coumes, C.; Gauffinet, S.; Chartier, D.; Stefan, L.; Le Bescop, P.

2017-01-01

This work is devoted to the conditioning of ion exchange resins used to decontaminate radioactive effluents. Calcium silicate cements may have a good potential to encapsulate spent resins. However, certain combinations of cement and resins produce a strong expansion of the final product, possibly leading to its full disintegration. The focus is placed on the understanding of the behaviour of cationic resins in the Na+ form in Portland or blast furnace slag (CEM III/C) cement pastes. During hydration of the Portland cement paste, the pore solution exhibits a decrease in its osmotic pressure, which causes a transient expansion of small magnitude of the resins. At 20 °C, this expansion takes place just after setting in a poorly consolidated material and is sufficient to induce cracks. In the CEM III/C paste, swelling of the resins also occurs, but before the end of setting, and induces limited stress in the matrix which is still plastic.

33 CFR 165.103 - Safety and Security Zones; LPG Vessel Transits in Portland, Maine, Captain of the Port Zone...

Science.gov (United States)

2010-07-01

... within a 500-yard radius of any Liquefied Petroleum Gas (LPG) vessel while it is moored at the LPG... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Safety and Security Zones; LPG... and Security Zones; LPG Vessel Transits in Portland, Maine, Captain of the Port Zone, Portsmouth...

Propriedades mecânicas de materiais compósitos à base de cimento Portland e resina epoxi Mechanical properties of composite materials based on portland cement and epoxy resin

Directory of Open Access Journals (Sweden)

T. H. Panzera

2010-03-01

Full Text Available O estudo de materiais de alto desempenho e multifuncionais, como os compósitos poliméricos cimentícios, tem sido o foco de inúmeras pesquisas na indústria da construção civil. Este trabalho investiga o efeito da combinação de uma fase polimérica termorrígida, uma resina epóxi, com cimento Portland branco estrutural, seguido da avaliação da resistência à compressão e módulo de elasticidade. Este compósito, quando comparado individualmente com as suas matérias-prima originais, promove um aumento da resistência mecânica à compressão, redução da massa específica e, também uma mudança significativa do comportamento mecânico. As mudanças nas propriedades mecânicas estão associadas à hidratação da fase cimentícia na presença da resina, fato comprovado através da análise espectroscópica na região do infravermelho.The study of multi-functional materials of high performance, as the polymeric-cementitious composites, has been the focus of several researches in the industry of the civil engineering. This work investigates the effect of the combination of a thermorigid epoxy phase and the white Portland cement, followed by the evaluation of its compressive strength and modulus of elasticity. This composite, when the phases are individually compared, provides an increase of the compressive strength, a reduction of the density, and a significant change of the mechanical behaviour. The changes in mechanical behaviour are associated with the hydration of cement in the presence of resin, which was evident after infrared spectroscopy analysis.

Hydration study of ordinary portland cement in the presence of zinc ions

Directory of Open Access Journals (Sweden)

Monica Adriana Trezza

2007-12-01

Full Text Available Hydration products of Portland cement pastes, hydrated in water and in the presence of zinc ions were studied comparatively at different ages. Hydration products were studied by X ray diffractions (XRD and infrared spectroscopy (IR. Although IR is not frequently used in cement chemistry, it evidenced a new phase Ca(Zn(OH32. 2H2O formed during cement hydration in the presence of zinc. The significant retardation of early cement hydration in the presence of zinc is assessed in detail by differential calorimetry as a complement to the study carried out by IR and XRD, providing evidence that permits to evaluate the kinetic of the early hydration.

Applying the Science of Science Communication to Climate Change and Clean Energy: Lessons Learned from the NSF- and PBS-supported "Earth: The Operators' Manual"

Science.gov (United States)

Haines-Stiles, G.; Akuginow, E.; Sanford, C.

2014-12-01

Yale legal scholar and professor of psychology Dan Kahan has criticized the climate change science community for not applying what's known about effective communications strategies to topics with potentially controversial content. "Earth: The Operators' Manual," funded by NSF's Informal Science Education program and appearing on PBS was hosted by Penn State geoscientist Richard Alley. From the initial proposal forward into airing on public television in 2011 and 2012, ETOM aimed to be authoritative and apolitical while still being engaging to general audiences. Based on social scientific insights from project Advisor, Suzanne Moser, and others, ETOM aimed to avoid "climate porn" scare tactics and over-used footage, and to enlist a diverse group of "messengers" in addition to Alley. An important design criterion was to give equal time to clean energy solutions while pulling no punches as to the consensus findings of leading climate scientists. With the ETOM project now completed and final reports submitted to NSF, what results can be shared to inform future efforts? And how did ETOM compare in audience impact with other major media efforts such as Al Gore's "An Inconvenient Truth" or Showtime's more recent "Years of Living Dangerously"? Results reported draw on the external evaluation by Rockman Et Al, and include both quantitative and qualitative data. Key findings are the importance of including Texan ranchers enthusiastic about wind power alongside Navy Admirals adamant that climate change is human-caused and Marines implementing solar energy to reduce casualties incurred while transporting fossil fuels. In-person presentations by Alley and others at science centers served as de facto focus groups for scripting the TV programs, along with actual focus groups convened by Rockman. The 3rd program, ENERGY QUEST USA, documented 5 quite different communities, from Alaska to Forth Worth, Baltimore, Portland and Kansas, all using competition, local values, and economic

Aplicaciones prácticas de la espectroscopía de absorción infrarroja en el estudio de los crudos, del clínker y del cemento portland anhidro

OpenAIRE

Vázquez, Tomás

1980-01-01

En la primera parte de este trabajo (*) se trató brevemente y de una manera fundamentalmente práctica el estudio por espectroscopía infrarroja de calizas, arcillas, clínker portland y sus fases constituyentes. En, el presente trabajo finalizará esta exposición con una visión general de algunas posibilidades que tiene la espectroscopía IR en el estudio del cemento portland anhidro, así como el estudio breve de puzolanas, escorias y cenizas volantes, como adiciones activas.

Quantitative study on the effect of high-temperature curing at an early age on strength development of concrete. Experiment with mortar using moderate-heat portland cement

International Nuclear Information System (INIS)

Sugiyama, Hisashi; Chino, Shigeo

1999-01-01

The effect of high-temperature curing at an early age on the strength development of concrete using moderate-heat portland cement was quantitatively studied. High-temperature curing conditions were set so as to give systematic variations in the temperature-time factors. As a result, the integrated value of curing temperature during the period having a significant effect on the strength development was proposed as a parameter that expressed the degree of high-temperature curing. The effect of high-temperature curing on the strength development of concrete using moderate-heat portland cement could be exactly predicted with the integrated value of curing temperature during the period from 0 to 3 days. (author)

Determination of the leaching rate of radionuclide 134Cs from the solidified radioactive wastes in Syrian Portland cement and cement-microsilica matrixes

International Nuclear Information System (INIS)

Ismail Shaaban; Nasim Assi

2010-01-01

The suitability of Syrian Portland cement for disposal of solidified low-level radioactive waste was assessed by measuring the leaching rate of 134 Cs. In ordinary cement concrete, a leaching rate of 1.309 x 10 -3 g/cm 2 per day was measured. Mixing this concrete with microsilica reduced significantly the leaching rate to 3.106 x 10 -4 g/cm 2 per day for 1% mixing, and to 9.645 x 10 -5 g/cm 2 per day for 3% mixing. It was also found that the application of a latex paint reduced these leaching rates by about 10%. These results, along with mechanical strength tests (under radiation exposure, high temperature, long water immersion and freeze-thaw cycling) indicate that Syrian Portland cement is suited for the disposal of low-level radioactive waste. (author)

Utility of the Mayo-Portland adaptability inventory-4 for self-reported outcomes in a military sample with traumatic brain injury.

Science.gov (United States)

Kean, Jacob; Malec, James F; Cooper, Douglas B; Bowles, Amy O

2013-12-01

To investigate the psychometric properties of the Mayo-Portland Adaptability Inventory-4 (MPAI-4) obtained by self-report in a large sample of active duty military personnel with traumatic brain injury (TBI). Consecutive cohort who completed the MPAI-4 as a part of a larger battery of clinical outcome measures at the time of intake to an outpatient brain injury clinic. Medical center. Consecutively referred sample of active duty military personnel (N=404) who suffered predominantly mild (n=355), but also moderate (n=37) and severe (n=12), TBI. Not applicable. MPAI-4 RESULTS: Initial factor analysis suggested 2 salient dimensions. In subsequent analysis, the ratio of the first and second eigenvalues (6.84:1) and parallel analysis indicated sufficient unidimensionality in 26 retained items. Iterative Rasch analysis resulted in the rescaling of the measure and the removal of 5 additional items for poor fit. The items of the final 21-item Mayo-Portland Adaptability Inventory-military were locally independent, demonstrated monotonically increasing responses, adequately fit the item response model, and permitted the identification of nearly 5 statistically distinct levels of disability in the study population. Slight mistargeting of the population resulted in the global outcome, as measured by the Mayo-Portland Adaptability Inventory-military, tending to be less reflective of very mild levels of disability. These data collected in a relatively large sample of active duty service members with TBI provide insight into the ability of patients to self-report functional impairment and the distinct effects of military deployment on outcome, providing important guidance for the meaningful measurement of outcome in this population. Copyright © 2013 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights reserved.

Microstructure: Surface and cross-sectional studies of hydroxyapatite formation on the surface of white Portland cement paste in vitro

International Nuclear Information System (INIS)

Chaipanich, Arnon; Torkittikul, Pincha

2011-01-01

The formation of hydroxyapatite was investigated at the surface and at the cross-section of white Portland cement paste samples before and after immersion in simulated body fluid. Scanning electron microscope images showed that hydroxyapatite were found at the surface of white Portland cement after immersion in simulated body fluid. Hydroxyapatite grains of mostly ∼1 μm size with some grain size of ∼2-3 μm were seen after 4 days immersion period. More estabilshed hydroxyapatite grain size of ∼3 μm grains were observed at longer period of immersion at 7 and 10 days. The cross-section of the samples was investigated using line scanning technique and was used to determine the hydroxyapatite layer. A strong spectrum of phosphorus is detected up to 6-8 μm depth for samples after 4, 7 and 10 days immersion in simulated body fluid when compared to weak spectrum detected before immersion. The increase in the phosphorus spectrum corresponds to the hydroxyapatite formation on the surface of the samples after the samples were placed in simulated body fluid.

Normal and refractory concretes for LMFBR applications. Volume 1. Review of literature on high-temperature behavior of portland cement and refractory concretes. Final report

International Nuclear Information System (INIS)

Bazant, Z.P.; Chern, J.C.; Abrams, M.S.; Gillen, M.P.

1982-06-01

The extensive literature on the properties and behavior at elevated temperature of portland cement concrete and various refractory concretes was reviewed to collect in concise form the physical and chemical properties of castable refractory concretes and of conventional portland cement concretes at elevated temperature. This survey, together with an extensive bibliography of source documents, is presented in Volume 1. A comparison was made of these properties, the relative advantages of the various concretes was evaluated for possible liquid metal fast breeder reactor applications, and a selection was made of several materials of interest for such applications. Volume 2 concludes with a summary of additional knowledge needed to support such uses of these materials together with recommendations on research to provide that knowledge

Applications of solid-state Nuclear Magnetic Resonance (NMR) in studies of Portland cements-based materials

DEFF Research Database (Denmark)

Skibsted, Jørgen; Andersen, Morten Daugaard; Jakobsen, Hans Jørgen

2007-01-01

Solid-state NMR spectroscopy represents an important research tool in the characterization of a range of structural properties for cement-based materials. Different approaches of the technique can be used to obtain information on hydration kinetics, mobile and bound water, porosity, and local...... atomic structures. After a short introduction to these NMR techniques, it is exemplified how magic-angle spinning (MAS) NMR can provide quantitative and structural information about specific phases in anhydrous and hydrated Portland cements with main emphasis on the incorporation of Al3+ ions...

Introducción a la fabricación y normalización del cemento portland

OpenAIRE

Sanjuán Barbudo, Miguel Ángel; Chinchón Yepes, Servando

2014-01-01

El cemento portland es un conglomerante hidráulico cuya principal propiedad es la de formar masas pétreas resistentes y duraderas cuando se mezcla con áridos y agua. El endurecimiento de la mezcla ocurre transcurrido un cierto tiempo desde el momento en que se realiza el amasado, lo que permite dar forma a la piedra artificial resultante. Estas tres cualidades (moldeable, resistente, duradero) hacen que los productos derivados del cemento tengan una gran aplicación en la construcción de edifi...

Aplicaciones prácticas de la espectroscopía de absorción infrarroja en el estudio de los crudos, del clínker y del cemento portland anhidro

Directory of Open Access Journals (Sweden)

Vázquez, Tomás

1980-09-01

Full Text Available Not available

En la primera parte de este trabajo (* se trató brevemente y de una manera fundamentalmente práctica el estudio por espectroscopía infrarroja de calizas, arcillas, clínker portland y sus fases constituyentes. En, el presente trabajo finalizará esta exposición con una visión general de algunas posibilidades que tiene la espectroscopía IR en el estudio del cemento portland anhidro, así como el estudio breve de puzolanas, escorias y cenizas volantes, como adiciones activas.

Effects of the super plasticizers and the water/cement ratio on the mini-slump of Portland cement pastes

International Nuclear Information System (INIS)

Meirelles, J.R.; Morelli, A.C.; Baldo, J.B.

1998-01-01

The rheology of Portland cement concrete is dominated by the cement paste rheology. In general the rheological behavior of cement pastes is evaluated by means of the mini-slump test. In the present paper it was investigated the effect of the water/cement ratio was as of two types of superplasticizers (melamine and naftalen based) on the mini-slump of pastes of common cement pastes. (author)

Análises do comportamento físico de um solo contaminado por borra oleosa ácida e encapsulado com cimento Portland Analyses of physical behavior of a soil contaminated by acidic oily sludge and encapsulated with cement Portland

Directory of Open Access Journals (Sweden)

José Waldomiro Jiménez Rojas

2008-06-01

Full Text Available Este trabalho tem como objetivo aplicar a técnica de encapsulamento em um solo contaminado com crescentes quantidades do resíduo industrial borra oleosa ácida, utilizando como agente encapsulante o cimento Portland CP-V ARI. A aplicação da técnica de encapsulamento consistiu na realização de estudos pós-tratamento, analisando fisicamente o solo contaminado através de ensaios de resistência à compressão simples e durabilidade. Os resultados apontam que quanto maior a quantidade de borra oleosa ácida presente no solo encapsulado, menor a resistência à compressão simples e maior a perda de massa.The objective of this study is applying the encapsulation technique in soil contaminated with increasing amounts of acidic oily sludge industrial residues, using Portland cement CP-V ARI as the encapsulating agent. The application of the encapsulation technique consisted in the accomplishment of post-treatment studies, analyzing the contaminated soil physically through unconfined compressive strength and durability tests. The results showed that an increasing amount of acidic oily sludge in the encapsulated soil ends up lowering the unconfined compressive strength as well as increasing the mass loss.

Portland Energy Centre: Securing supply and clearing the air

International Nuclear Information System (INIS)

2003-02-01

The rationale for, and benefits derivable from the proposed Portland natural gas-fired cogeneration plant, to be located beside the former Hearn power station near the Leslie Street Spit in Toronto, are discussed. The justification for and the single most important benefit promised by the proposed plant is that it could help Ontario achieve its coal phase-out target by displacing 100 per cent of the annual output of the Lakeview coal--fired power plant in Mississauga, as well as six per cent of the annual output of the Nanticoke coal-fired power plant, in total supplying about 10 per cent of Toronto's electricity needs and providing steam to heat several office towers in downtown Toronto. Other benefits discussed include substantially improved air quality, reduced incidence of asthma and heart attacks, a more reliable power supply for Toronto, some 500 new jobs during construction, and 25 to 35 permanent jobs to operate the plant. The Fact Sheet also offers suggestions on how to generate political support for this project in particular and for renewable power sources in general

An Experimental Study of Portland Cement and Superfine Cement Slurry Grouting in Loose Sand and Sandy Soil

OpenAIRE

Weijing Yao; Jianyong Pang; Yushan Liu

2018-01-01

Grouting technology is widely applied in the fields of geotechnical engineering in infrastructure. Loose sand and sandy soil are common poor soils in tunnel and foundation treatments. It is necessary to use superfine cement slurry grouting in the micro-cracks of soil. The different effectiveness of Portland cement slurry and superfine cement slurry in sandy soil by the laboratory grouting experiment method were presented in this paper. The grouting situations of superfine cement slurry inject...

Acquisition of an Electron Back Scatter Diffraction (EBSD) system for the Zeiss Sigma SEM at Portland State University -- Planetary Major Equipment

Science.gov (United States)

Ruzicka, Alex

To build on our parent Origins program award, entitled "Shock histories of chondrites as revealed by combined microstructural (TEM), petrographic, and X-ray microtomographic (micro-CT) analysis", we are requesting as Planetary Major Equipment the acquisition of an Electron Back Scatter Diffraction (EBSD) system, which will integrate with a Zeiss Sigma SEM that was installed at Portland State University last year (2010). This EBSD system will greatly augment the science return of the parent grant by allowing quantitative measurements of strain and textural fabrics in grains of all sizes and types across an entire thin section. Such measurements will help link data that are already being obtained with optical light microscopy, transmission electron microscopy, and micro- tomography methods. More generally, the EBSD system will augment the PI's research on the petrology of extraterrestrial materials by providing an additional tool for petrographic analyses, with data that can be used to evaluate strain, grain orientations, grain size distributions, phase proportions, and mineralogy. The equipment will enable quantitative characterization of the crystallography of primitive extraterrestrial materials, which will contribute to a better understanding of the formation and evolution of planetary systems, a major goal of NASA.

Acquisition of an Electron Back Scatter Diffraction (EBSD) system for the Zeiss Sigma SEM at Portland State University Planetary Major Equipment

Science.gov (United States)

Ruzicka, Alex

To build on our parent Origins program award, entitled "Shock histories of chondrites as revealed by combined microstructural (TEM), petrographic, and X-ray microtomographic (micro-CT) analysis", we are requesting as Planetary Major Equipment the acquisition of an Electron Back Scatter Diffraction (EBSD) system, which will integrate with a Zeiss Sigma SEM that was installed at Portland State University last year (2010). This EBSD system will greatly augment the science return of the parent grant by allowing quantitative measurements of strain and textural fabrics in grains of all sizes and types across an entire thin section. Such measurements will help link data that are already being obtained with optical light microscopy, transmission electron microscopy, and micro- tomography methods. More generally, the EBSD system will augment the PI's research on the petrology of extraterrestrial materials by providing an additional tool for petrographic analyses, with data that can be used to evaluate strain, grain orientations, grain size distributions, phase proportions, and mineralogy. The equipment will enable quantitative characterization of the crystallography of primitive extraterrestrial materials, which will contribute to a better understanding of the formation and evolution of planetary systems, a major goal of NASA.

Mesenchymal Stem Cells for the Prevention of Acute Respiratory Distress Syndrome after Pulmonary Contusion and Hemorrhagic Shock

Science.gov (United States)

2017-10-01

Contusion and Hemorrhagic Shock PRINCIPAL INVESTIGATOR: Martin Schreiber, MD CONTRACTING ORGANIZATION: Oregon Health & Science University Portland, OR...PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) Oregon Health & Science University 3181 SW Sam Jackson Park Road, Portland, OR 97239 Blood Systems...extubated the animals was not logistically or physically feasible. To improve the welfare of the animal and consistency in the model, we revised our model

Análisis cuantitativo de cuarzo-alfa en mezclas de cemento portland anhidro y calcita sintética por difracción de rayos X con equipo Philips PW-1700

Directory of Open Access Journals (Sweden)

Sagrera-Moreno, J. L.

1985-09-01

Full Text Available In this article there are explained the necessary steps to make up a quantitative analysis of alpha-quartz applying the technique of rays X diffraction, in artificial mixtures of anhydrous portland cement and synthetic calcite, which contents are known.

En el presente artículo se explican los pasos necesarios para realizar un análisis cuantitativo de cuarzo-alfa aplicando la técnica de difracción de rayos X en mezclas artificiales de cemento portland anhidro y calcita sintética, cuyos contenidos son conocidos.

Chemical and morphological characteristics of mineral trioxide aggregate and Portland cements.

Science.gov (United States)

Khan, Shahbaz; Kaleem, Muhammad; Fareed, Muhammad Amber; Habib, Amir; Iqbal, Kefi; Aslam, Ayesha; Ud Din, Shahab

2016-01-01

The purpose of this study was to investigate the chemical composition and particle morphology of white mineral trioxide aggregate (WMTA) and two white Portland cements (CEM 1 and CEM 2). Compositional analysis was performed by energy dispersive X-ray spectroscopy, X-ray fluorescence spectrometry and X-ray diffraction whereas, morphological characteristics were analyzed by scanning electron microscope and Laser scattering particle size distribution analyzer. The elemental composition of WMTA, CEM 1 and CEM 2 were similar except for the presence of higher amounts of bismuth in WMTA. Calcium oxide and silicon oxide constitute the major portion of the three materials whereas, tricalcium silicate was detected as the major mineral phase. The particle size distribution and morphology of WMTA was finer compared to CEM 1 and CEM 2. The three tested materials had relatively similar chemical composition and irregular particle morphologies.

Planning, zoning and financial incentives for ecoroofs in Portland, Oregon

Energy Technology Data Exchange (ETDEWEB)

Liptan, T. [City of Portland, OR (United States). Bureau of Environmental Services

2003-07-01

Approximately 35 to 90 per cent of the surface area of various city neighbourhoods is composed of rooftops and pavement. The City of Portland has suffered from several infrastructure and environmental problems as a result of these rooftops and pavement. In response, the City created a program to address storm water related problems and to provide other environmental benefits. This program promotes the use of Ecoroofs or vegetated roofs. City officials are investigating three specific concerns regarding Ecoroofs: (1) the extent to which Ecoroofs can manage precipitation and water quality, (2) the design, construction and maintenance issues to be addressed in order to ensure Ecoroofs are viable, and (3) the policies and economic concerns that must be addressed to determine the appropriate incentives and potential regulations for Ecoroofs. The overall city program was described in this presentation. The incentives and assistance provided by the city were reviewed, and the practical lessons learned were discussed. 1 tab., 1 fig.

Análise microscópica da polpa dental de cães após pulpotomia e proteção pulpar com agregado de trióxido mineral e cimento Portland branco

OpenAIRE

Menezes, Renato; Bramante, Clóvis Monteiro; Garcia, Roberto Brandão; Letra, Ariadne; Carvalho, Vanessa Graciela Gomes; Carneiro, Everdan; Brunini, Sérgio; Oliveira, Rodrigo Cardoso; Canova, Giovana Calichio; Moraes, Fernanda Gomes de

2004-01-01

Considering previous studies on the similarity between the chemical composition of the mineral trioxide aggregate and the Portland cement, the purpose of this study was to investigate the pulp response of dog's teeth after pulpotomy and direct pulp protection with MTA Angelus and white Portland cement. Thirty eight pulp remnants were protected with these materials. One hundred and twenty days after treatment, the animals were sacrificed and the specimens removed and prepared for histological ...

Waste-form development for conversion to portland cement at Los Alamos National Laboratory (LANL) Technical Area 55 (TA-55)

International Nuclear Information System (INIS)

Veazey, G.W.; Schake, A.R.; Shalek, P.D.; Romero, D.A.; Smith, C.A.

1996-10-01

The process used at TA-55 to cement transuranic (TRU) waste has experienced several problems with the gypsum-based cement currently being used. Specifically, the waste form could not reliably pass the Waste Isolation Pilot Plant (WIPP) prohibition for free liquid and the Environmental Protection Agency (EPA)-Toxicity Characteristic Leaching Procedure (TCLP) standard for chromium. This report describes the project to develop a portland cement-based waste form that ensures compliance to these standards, as well as other performance standards consisting of homogeneous mixing, moderate hydration temperature, timely initial set, and structural durability. Testing was conducted using the two most common waste streams requiring cementation as of February 1994, lean residue (LR)- and oxalate filtrate (OX)-based evaporator bottoms (EV). A formulation with a pH of 10.3 to 12.1 and a minimum cement-to-liquid (C/L) ratio of 0.80 kg/l for OX-based EV and 0.94 kg/L for LR-based EV was found to pass the performance standards chosen for this project. The implementation of the portland process should result in a yearly cost savings for raw materials of approximately $27,000 over the gypsum process

Arsenic content in Portland cement: a literature review.

Science.gov (United States)

Tenório de Franca, Talita Ribeiro; da Silva, Raphaela Juvenal; Sedycias de Queiroz, Michellini; Aguiar, Carlos Menezes

2010-01-01

Portland cement (PC) is a hydraulic binding material widely used in the building industry. The main interest in its use in dentistry is focused on a possible alternative to mineral trioxide aggregate (MTA) because PC is less expensive and is widely available. In dentistry, PC has been used in dental procedures such as pulpotomy, pulp capping, repair of root perforation and root-end filling. The purpose of this article is review the dental literature about the PC, its composition with special attention to arsenic content, properties, and application in dentistry. A bibliographic research was performed in Bireme, PubMed, LILACS and Scopus data bases looking for national and international studies about the PC composition, properties and clinical use. It was observed that PC has favorable biological properties very similar to those of MTA. The PC has shown good cell proliferation induction with formation of a monolayer cell, satisfactory inflammatory response, inhibitory effect of prostaglandin and antimicrobial effect. Studies have shown that PC is not cytotoxic, stimulates the apposition of reparative dentin and permits cellular attachment and growth. Regarding arsenic presence, its levels and release are low. PC has physical, chemical and biological properties similar to MTA. Arsenic levels and release are low, therefore, unable to cause toxic effects.

Arsenic content in Portland cement: A literature review

Directory of Open Access Journals (Sweden)

Tenorio de Franca Talita

2010-01-01

Full Text Available Portland cement (PC is a hydraulic binding material widely used in the building industry. The main interest in its use in dentistry is focused on a possible alternative to mineral trioxide aggregate (MTA because PC is less expensive and is widely available. In dentistry, PC has been used in dental procedures such as pulpotomy, pulp capping, repair of root perforation and root-end filling. The purpose of this article is review the dental literature about the PC, its composition with special attention to arsenic content, properties, and application in dentistry. A bibliographic research was performed in Bireme, PubMed, LILACS and Scopus data bases looking for national and international studies about the PC composition, properties and clinical use. It was observed that PC has favorable biological properties very similar to those of MTA. The PC has shown good cell proliferation induction with formation of a monolayer cell, satisfactory inflammatory response, inhibitory effect of prostaglandin and antimicrobial effect. Studies have shown that PC is not cytotoxic, stimulates the apposition of reparative dentin and permits cellular attachment and growth. Regarding arsenic presence, its levels and release are low. PC has physical, chemical and biological properties similar to MTA. Arsenic levels and release are low, therefore, unable to cause toxic effects.

Development of a CE-QUAL-W2 temperature model for Crystal Springs Lake, Portland, Oregon

Science.gov (United States)

Buccola, Norman L.; Stonewall, Adam J.

2016-05-19

During summer 2014, lake level, streamflow, and water temperature in and around Crystal Springs Lake in Portland, Oregon, were measured by the U.S. Geological Survey and the City of Portland Bureau of Environmental Services to better understand the effect of the lake on Crystal Springs Creek and Johnson Creek downstream. Johnson Creek is listed as an impaired water body for temperature by the Oregon Department of Environmental Quality (ODEQ), as required by section 303(d) of the Clean Water Act. A temperature total maximum daily load applies to all streams in the Johnson Creek watershed, including Crystal Springs Creek. Summer water temperatures downstream of Crystal Springs Lake and the Golf Pond regularly exceed the ODEQ numeric criterion of 64.4 °F (18.0 °C) for salmonid rearing and migration. To better understand temperature contributions of this system, the U.S. Geological Survey developed two-dimensional hydrodynamic water temperature models of Crystal Springs Lake and the Golf Pond. Model grids were developed to closely resemble the bathymetry of the lake and pond using data from a 2014 survey. The calibrated models simulated surface water elevations to within 0.06 foot (0.02 meter) and outflow water temperature to within 1.08 °F (0.60 °C). Streamflow, water temperature, and lake elevation data collected during summer 2014 supplied the boundary and reference conditions for the model. Measured discrepancies between outflow and inflow from the lake, assumed to be mostly from unknown and diffuse springs under the lake, accounted for about 46 percent of the total inflow to the lake.

Effect of different radiopacifying agents on the physicochemical properties of white Portland cement and white mineral trioxide aggregate.

Science.gov (United States)

Hungaro Duarte, Marco Antonio; Minotti, Paloma Gagliardi; Rodrigues, Clarissa Teles; Zapata, Ronald Ordinola; Bramante, Clovis Monteiro; Tanomaru Filho, Mário; Vivan, Rodrigo Ricci; Gomes de Moraes, Ivaldo; Bombarda de Andrade, Flaviana

2012-03-01

The aim of this study was to evaluate the pH, calcium ion release, setting time, and solubility of white mineral trioxide aggregate (WMTA) and white Portland cement (WPC) combined with the following radiopacifying agents: bismuth oxide (BO), calcium tungstate (CT), and zirconium oxide (ZO). Fifty acrylic teeth with root-end filling material were immersed in ultrapure water for measurement of pH and calcium release (atomic absorption spectrophotometry) at 3, 24, 72, and 168 hours. For evaluation of setting time, each material was analyzed according to the American Society for Testing and Materials guidelines 266/08. The solubility test was performed according to American National Standards Institute/American Dental Association specification no. 57/2000. Solubility, setting time, and pH values were compared by using analysis of variance and Tukey test, and the values of calcium release were compared by the Kruskal-Wallis and Miller tests. The significance level was set at 5%. The pH and calcium release were higher at 3 and 24 hours. WPC was the material with the higher values for both properties. WMTA had the greatest solubility among all materials (P Portland cement. Copyright © 2012 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Microbial leakage of MTA, Portland cement, Sealapex and zinc oxide-eugenol as root-end filling materials.

Science.gov (United States)

Estrela, Carlos; Estrada-Bernabé, Pedro-Felício; de Almeida-Decurcio, Daniel; Almeida-Silva, Julio; Rodrigues-Araújo-Estrela, Cyntia; Poli-Figueiredo, José-Antonio

2011-05-01

The aim of this study was to compare the microbial leakage of mineral trioxide aggregate (MTA), Portland cement (PC), Sealapex and zinc oxide-eugenol (ZOE) as root-end filling materials. An in vitro microbial leakage test (MLT) with a split chamber was used in this study. A mixture of facultative bacteria and one yeast (S. aureus+E. faecalis+P. aeruginosa+B. subtilis+C. albicans) was placed in the upper chamber and it could only reach the lower chamber containing Brain Heart Infusion broth by way of leakage through the root-end filling. Microbial leakage was observed daily for 60 days. Sixty maxillary anterior human teeth were randomly assigned to different groups--MTA and PC (gray and white), Sealapex+zinc oxide and ZOE, control groups and subgroups to evaluate the influence of EDTA for smear layer removal. These materials were further evaluated by an agar diffusion test (ADT) to verify their antimicrobial efficacy. Data were analyzed statistically by Kruskal-Wallis and Mann-Whitney test. In the MLT, Sealapex+zinc oxide and ZOE did not show evidence of microbial leakage over the 60-day experimental period. The other materials showed leakage from the 15th day. The presence of smear layer influenced microbial leakage. Microbial inhibition zones were not observed in all samples tested by ADT. Sealapex+zinc oxide and ZOE did not show microbial leakage over the experimental period, whereas it was verified within 15 to 45 days in MTA and Portland cement.

An Experimental Study of Portland Cement and Superfine Cement Slurry Grouting in Loose Sand and Sandy Soil

Directory of Open Access Journals (Sweden)

Weijing Yao

2018-04-01

Full Text Available Grouting technology is widely applied in the fields of geotechnical engineering in infrastructure. Loose sand and sandy soil are common poor soils in tunnel and foundation treatments. It is necessary to use superfine cement slurry grouting in the micro-cracks of soil. The different effectiveness of Portland cement slurry and superfine cement slurry in sandy soil by the laboratory grouting experiment method were presented in this paper. The grouting situations of superfine cement slurry injected into sand and sandy soil were explored. The investigated parameters were the dry density, wet density, moisture content, internal friction angle, and cohesion force. The results show that the consolidation effect of superfine cement is better than that of Portland cement due to the small size of superfine cement particles. The superfine cement can diffuse into the sand by infiltration, extrusion, and splitting. When the water–cement ratio of superfine cement slurry is less than 2:1 grouting into loose sand, the dry and wet density decrease with the increase in the water–cement ratio, while the moisture content and cohesive force gradually increase. When the water–cement ratio of superfine cement slurry is 1:1 grouting into loose sand and sandy soil, the dry density, wet density, and cohesive force of loose sand are larger than those of sandy soil. The results of the experiment may be relevant for engineering applications.

Modeling the degradation of Portland cement pastes by biogenic organic acids

International Nuclear Information System (INIS)

De Windt, Laurent; Devillers, Philippe

2010-01-01

Reactive transport models can be used to assess the long-term performance of cement-based materials subjected to biodegradation. A bioleaching test (with Aspergillus niger fungi) applied to ordinary Portland cement pastes during 15 months is modeled with HYTEC. Modeling indicates that the biogenic organic acids (acetic, butyric, lactic and oxalic) strongly accelerate hydrate dissolution by acidic hydrolysis whilst their complexation of aluminum has an effect on the secondary gel stability only. The deepest degradation front corresponds to portlandite dissolution and decalcification of calcium silicate hydrates. A complex pattern of sulfate phases dissolution and precipitation takes place in an intermediate zone. The outermost degraded zone consists of alumina and silica gels. The modeling accurateness of calcium leaching, pH evolution and degradation thickness is consistently enhanced whilst considering increase of diffusivity in the degraded zones. Precipitation of calcium oxalate is predicted by modeling but was hindered in the bioleaching reactor.

Zero Energy With an Affordable Price Tag: Friends School of Portland

Energy Technology Data Exchange (ETDEWEB)

Torcellini, Paul A [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2017-08-09

More than half of all operating school districts in the U.S. are in rural areas. These small schools operate at a different scale and have different needs than their city counterparts. In 2003-2004, 20% of public schools in the U.S. served fewer than 200 students(1). Although the Friends School of Portland - which was designed to achieve both zero energy performance and Passivhaus certification - is an independent school, it faced financial constraints similar to those faced by many other small schools throughout the country. The project was financed through a capital campaign and a mortgage that forced a hard cost cap on the project, so the project team had to be diligent about every dollar that was spent. In its first year of operation, the school site energy use intensity was just 12 kbtu/ft2, a bit more than the 9 kbtu/ft2 predicted.

Efeito do tempo de cura na rigidez de argamassas produzidas com cimento Portland Effect of the curing time on the stiffness of mortars produced with Portland cement

Directory of Open Access Journals (Sweden)

G. C. R. Garcia

2011-03-01

Full Text Available O concreto de cimento Portland é um dos materiais mais usados no mundo inteiro, entretanto, devido a sua estrutura ser muito complexa, torna-se imprescindível estudar suas propriedades com bastante profundidade. O concreto é produzido a partir de uma argamassa, de areia e cimento, com adição de agregados graúdos, sendo que suas propriedades estão basicamente suportadas nessa argamassa de constituição. O objetivo deste trabalho foi estudar a variação da rigidez de duas argamassas de composições com razão cimento:areia de 1:2 e 1:3 em função do tempo de cura, tendo como parâmetro a variação do módulo de Young. Os resultados mostraram que o módulo de Young cresce até atingir o valor máximo no oitavo dia, sendo que nos três primeiros dias esse crescimento é mais acentuado. A análise dos resultados indica que grande parte do processo de hidratação do cimento, com formação das ligações químicas responsáveis pela rigidez da argamassa, acontece nos primeiros dias de cura.Concrete produced with Portland cement is one of building materials most widely used worldwide. However, due to its highly complex structure, its properties require in-depth studies. Concrete is a mortar consisting of a mixture of cement, sand and coarse aggregates, and its properties are represented basically by the mortar base. The aim of this work was to study the change in stiffness of two mortar compositions cured at 25 ºC with a cement-to-sand ratio of 1:2 and 1:3, as a function of curing time using the variation of Young modulus as the measuring parameter. The results showed that Young modulus increases up to a maximum value on the 8th day, and that this increase is more pronounced during the first three days. An analysis of the results indicates that a large part of the cement hydration process, involving the formation of chemical bonds that are responsible for the mortar stiffness, takes place in the early days of curing.

Evaluating the freeze-thaw durability of portland cement-stabilized-solidified heavy metal waste using acoustic measurements

International Nuclear Information System (INIS)

El-Korchi, T.; Gress, D.; Baldwin, K.; Bishop, P.

1989-01-01

The use of stress wave propagation to assess freeze-thaw resistance of portland cement solidified/stabilized waste is presented. The stress wave technique is sensitive to the internal structure of the specimens and would detect structural deterioration independent of weight loss or visual observations. The freeze-thaw resistance of a cement-solidified cadmium waste and a control was evaluated. The control and cadmium wastes both showed poor freeze-thaw resistance. However, the addition of cadmium and seawater curing increased the resistance to more cycles of freezing and thawing. This is attributed to microstructural changes

Behavioral and Social Sciences at the National Institutes of Health: adoption of research findings in health research and practice as a scientific priority.

Science.gov (United States)

Riley, William T

2017-06-01

The National Institutes of Health's Office of Behavioral and Social Sciences Research (OBSSR) recently released its Strategic Plan for 2017 to 2021. This plan highlights three scientific priorities: (1) improve the synergy of basic and applied behavioral and social sciences research, (2) enhance and promote the research infrastructure, methods, and measures needed to support a more cumulative and integrated approach to behavioral and social sciences research, and (3) facilitate the adoption of behavioral and social sciences research findings in health research and in practice. This commentary focuses on the challenges and opportunities to facilitate the adoption of research findings in health research and in practice. In addition to the ongoing NIH support for dissemination and implementation (D&I) research, we must address transformative challenges and opportunities such as better disseminating and implementing D&I research, merging research and practice, adopting more rigorous and diverse methods and measures for both D&I and clinical trials research, evaluating technological-based delivery of interventions, and transitioning from minimally adaptable intervention packages to planned adaptations rooted in behavior change principles. Beyond translation into practice and policy, the OBSSR Strategic Plan also highlights the need for translation of behavioral and social science findings into the broader biomedical research enterprise.

Costs and benefits of bicycling investments in Portland, Oregon.

Science.gov (United States)

Gotschi, Thomas

2011-01-01

Promoting bicycling has great potential to increase overall physical activity; however, significant uncertainty exists with regard to the amount and effectiveness of investment needed for infrastructure. The objective of this study is to assess how costs of Portland's past and planned investments in bicycling relate to health and other benefits. Costs of investment plans are compared with 2 types of monetized health benefits, health care cost savings and value of statistical life savings. Levels of bicycling are estimated using past trends, future mode share goals, and a traffic demand model. By 2040, investments in the range of $138 to $605 million will result in health care cost savings of $388 to $594 million, fuel savings of $143 to $218 million, and savings in value of statistical lives of $7 to $12 billion. The benefit-cost ratios for health care and fuel savings are between 3.8 and 1.2 to 1, and an order of magnitude larger when value of statistical lives is used. This first of its kind cost-benefit analysis of investments in bicycling in a US city shows that such efforts are cost-effective, even when only a limited selection of benefits is considered.

Potencialidades de um caulim calcinado como material de substituição parcial do cimento portland em argamassas Potentialities of a calcined kaolin as material of partial replacement of portland cement in mortars

Directory of Open Access Journals (Sweden)

Marilia P. de Oliveira

2006-06-01

Full Text Available A utilização de argilas calcinadas na forma de metacaulinita, como material pozolânico para argamassas e concretos, tem recebido atenção considerável nos últimos anos. Este trabalho objetivou avaliar o desempenho mecânico de argamassas, nas quais foi utilizado um caulim calcinado proveniente do Estado da Paraíba, como material de substituição parcial do cimento Portland. Utilizaram-se duas finuras do caulim: passando nas peneiras ABNT 200 (0,074 mm e 325 (0,044 mm e calcinados nas temperaturas de 700, 800 e 900 ºC pelo tempo de 2 h. As amostras foram caracterizadas através de análise química, análise térmica diferencial, difração de raios-X e área específica. Obteve-se o índice de atividade pozolânica com a cal e o cimento Portland. O percentual de substituição adotado foi de 0, 10, 20, 30 e 40%. A relação aglomerante: areia foi de 1:1,5 e a relação água/aglomerante fixada igual 0,4. O efeito da substituição parcial do cimento na argamassa foi avaliado através da resistência à compressão simples, nas idades de 7, 28 e 90 dias. As argamassas estudadas apresentaram resistência superior em relação à da referência, até o nível de 30% de substituição.The use of burnt clays, in the metakaolin form, as pozzolanic material for mortars and concretes has received a remarkable attention in the last years. This paper aimed to evaluate the mechanical property of mortars, in which a calcined kaolin originating from the State of Paraiba, was used as partial cement replacement material. Two finess of the kaolin were used: ABNT 200 (0.074 mm and 325 (0.044 mm and burnt at temperatures of 700, 800 and 900 ºC for a period of 2 h. Both materials were characterized by chemical analysis, differential thermal analysis, X-ray diffraction, specific area tests. The pozolanic activity index was obtanied using lime and cement Portland. The amounts of replacement were 10, 20, 30 and 40%, besides the reference mortar. The binder

Standard Test Method for Bond Strength of Ceramic Tile to Portland Cement Paste

CERN Document Server

American Society for Testing and Materials. Philadelphia

2002-01-01

1.1 This test method covers the determination of the ability of glazed ceramic wall tile, ceramic mosaic tile, quarry tile, and pavers to be bonded to portland cement paste. This test method includes both face-mounted and back-mounted tile. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Analysis by X-Ray images of wind blandes waste incorporated in Portland cement

International Nuclear Information System (INIS)

Marques, M.A.

2011-01-01

The wind blandes wastes can be reused in the incorporation in Portland cement, to be used in non-structural constructions. This work shows X-rays images to assessment the space distribution of the wastes in the cement and to evaluate the use of this methodology. Cylindrical specimens were produced according to ABNT NBR 5738 standards. The mass relation of sand, pebbles and cement was 3:2:1 and 10%, 20% and 50% of waste was incorporated in cement specimens. Frontal and upper projections were obtained in X-Rays images. The images showed that the distribution of the waste is homogeneous, consistent with what was intended in this type of incorporation, which can provide uniformity in test results of compressive strength. (author)

Influence of citric acid as setting retarder in CPV portland cement pastes and mortars; Influencia do acido citrico como retardador de pega em pastas e argamassas de cimento portland CPV ARI

Energy Technology Data Exchange (ETDEWEB)

Mendes, B.C.; Lopes, M.M.S.; Alvarenga, R.C.S.S.; Fassoni, D.P.; Pedroti, L.G. [Universidade Federal de Vicosa (UFV), MG (Brazil); Azevedo, A.R.G. de, E-mail: afonso.garcez91@gmail.com [Universidade Estadual do Norte Fluminense Darcy Ribeiro (UENF), Campos dos Goytacazes, RJ (Brazil)

2016-07-01

This work aims to study the availability of using and the influence of citric acid in the properties of pastes and mortars made with Portland cement CPV ARI both in fresh and hardened form. The citric acid dosages were 0, 0.4%, and 0.8% relative to the cement mass. The produced cement pastes were tested to determine normal consistency water and initial and final setting times. Mortars were tested to determine the consistency index, specific gravity, air entrained content in the fresh stage, hardened bulk density, compressive strength at ages 7, 14, and 28 days, and analysis by XRD technique. The results show that citric acid, besides improve the mortar workability, contribute to an increase in mechanical strength in older than 14 days. (author)

Effect of sewage sludge ash (SSA on the mechanical performance and corrosion levels of reinforced Portland cement mortars

Directory of Open Access Journals (Sweden)

Andión, L. G.ª

2006-06-01

Full Text Available The article describes a study conducted to determinecorrosion in reinforcement embedded in Portland cement(PC mortars with different percentages of sewage sludgeash (SSA admixtures. The polarization resistancetechnique was used to determine the steel corrosion rate(Icorr in the test specimens. The samples were subjectedto different environmental conditions and aggressiveagents: 100% relative humidity (RH, accelerated carbonationat 70% RH and seawater immersion. Portlandcement was partially substituted for SSA in the mixes atrates of 0, 10, 20, 30 and 60% (by mass to make thedifferent mortars. The results show that where cementwas replaced by SSA at rates of up to 10% by mass,mortar corrosion performance was comparable to thebehaviour observed in SSA-free mortars (control mortar:0% SSA. Data for higher rates are also shown. From themechanical standpoint, SSA exhibited moderate pozzolanicactivity and the best performance when SSA wasadded at a rate of 10% to mixes with a water/(binder:PC + SSA (w/b ratio of 0.5.Se ha estudiado el nivel de corrosion que presentan lasarmaduras embebidas en morteros fabricados con cementoPortland (CP con diferentes porcentajes de sustitucion deceniza de lodo de depuradora (CLD. Se ha utilizado la tecnicade la Resistencia a la Polarizacion para determinar lavelocidad de corrosion del acero embebido en las muestrasestudiadas. Las muestras se han sometido a diferentes condicionesambientales y agentes agresivos: 100% de humedadrelativa (HR, carbonatacion acelerada al 70% HR einmersion en agua de mar. Para la fabricacion de los distintosmorteros, el cemento Portland ha sido parcialmente sustituidopor CLD en los siguientes porcentajes en masa: 0,10, 20, 30 y 60%. Los resultados muestran que sustitucionesde cemento por CLD de hasta el 10% en masa no alteranel comportamiento frente a la corrosion de los morterosal compararlos con los morteros libres de CLD (morteroscontrol: 0% de sustitucion de cemento por CLD. Se

Resistência à compressão do solo-cimento com substituição parcial do cimento Portland por resíduo cerâmico moído Compressive strength of soil-cement with partial replacement of the Portland cement by crushed ceramic waste

Directory of Open Access Journals (Sweden)

Rivanildo Dallacort

2002-12-01

Full Text Available Neste trabalho, apresenta-se o estudo experimental da resistência à compressão do solo-cimento, com substituição parcial do cimento Portland por resíduo cerâmico moído. Para tanto, foram ensaiados 81 espécimenes cilíndricos desse material à compressão, em que parte do cimento foi substituída por material cerâmico moído. Realizou-se uma programação fatorial, na qual três variáveis foram selecionadas para estudo: o teor de material ligante (cimento + resíduo cerâmico, a umidade do solo e o teor de resíduo cerâmico adicionado. É apresentado um estudo estatístico através de análise de variância da massa específica do material e da resistência a compressão. Tal estudo permitiu concluir-se que substituições de 25 e 57% do teor de cimento por material cerâmico podem produzir blocos de solo-cimento com resistências superiores a 2 MPa, com teor de material ligante de 6 e 8%, respectivamente.In this paper, an experimental study of the compressive strength of soil-cement with partial replacement of the Portland cement by crushed ceramic waste is presented and discussed. For this, eighty-one cylindrical specimens of soil-cement were tested, where part of cement percentage was replaced by crushed ceramic waste. The experiment was conducted in factorial design and three variables were selected and studied: the binding material content (cement + ceramic waste, soil moisture content and the ratio of ceramic waste. A statistical study using variance analysis of the specific mass and compressive strength of the material is presented. This study concluded that replacement ratios of 25 and 57% of the Portland cement by crushed ceramic material can be used to fabricate soil-cement bricks with strength higher than 2 MPa, for a binding material content of 6 and 8% respectively.

Diffusion of He in OPC paste and low-heat Portland cement paste containing fly-ash in contact with aqueous phase

International Nuclear Information System (INIS)

Sato, Fuminori; Miwata, Chikanori; Noda, Natsuko; Sato, Seichi; Kozaki, Tamotsu; Higashihara, Tomohiro; Hironaga, Michihiko; Kawanishi, Motoi

2008-01-01

As a part of gas migration studies in concrete package for nuclear waste surrounded by water-saturated rock, the helium diffusion in ordinary Portland cement paste (OPC) was studied using disk form specimen at various water-to-cement (w/c) ratios. The helium diffusion in low-heat Portland cement paste containing fly-ash (LPF) was also studied. Apparent diffusion coefficients of helium in OPC paste were ∼1 x 10 -10 m 2 s -1 at 0.4 w/c ratio, independent of increase of w/c ratio. It is likely that the materials formation such as C-S-H and CH in capillary pores in OPC plays an important role on the helium diffusion rather than porosity increase. Apparent diffusion coefficient of helium in LPF was two orders of magnitude smaller than that in OPC. It is quite possible that the addition of fly-ash contributes to the formation of hydration products which markedly enhance discontinuity of capillary pore. The results of the present study on the two kinds of cement pastes give us valuable information about alternatives to release gas from cement package. (author)

Utilización de ladrillos de adobe estabilizados con cemento portland al 6% y reforzados con fibra de coco, para muros de carga en Tampico

Directory of Open Access Journals (Sweden)

Olivares Santiago, Manuel

2002-04-01

Full Text Available In this article conclusions are presented about adobe bricks stabilized with 6% portland cement and reinforced with different percentages of coconut fibers. The author, has developed an experimental plan in laboratory and has built in situ several walls with different bricks, different joints and different orientations, to analyze the behaviour ofthe brick prototypes for the weather conditions in Tampico.En este artículo se presentan las conclusiones acerca del refuerzo Ide ladrillos de adobe, estabilizados con cemento portland al 6% con diferentes porcentajes de fibra de coco. El autol; para llegar a estas conclusiones, desarrolla un plan experimental en laboratorio asi como construye in situ muestras de muros con diferentes clases de ladrillos, diferentes uniones entre ellos y distintas orientaciones, para analizar el comportamiento de prototipos ante las condiciones climáticas de la zona de Tampico.

Contribution to the determination of gypsum and hemihydrates content in Portland cements

Directory of Open Access Journals (Sweden)

Moreno Arús, Fernando

1975-09-01

Full Text Available Not availableLa mayoría de los técnicos de cemento, aceptan, que las anormalidades del fraguado, conocidas como "falso fraguado" en el cemento portland, se deben primordialmente a la presencia de yeso parcialmente deshidratado (S04Ca1/2H20. Si el clínker que se muele está enriquecido en cal libre, o la temperatura del molino es elevada (superior a los 110 °C o hay escasa ventilación de éste, se llega a originar una parcial deshidratación del yeso, que se mantiene durante el proceso de ensilado y que origina las anormalidades del fraguado al que anteriormente nos hemos referido. Por esta razón creemos muy importante poder conocer el grado de deshidratación en que se encuentra el yeso en un cemento.

A cognitive stressor for event-related potential studies: the Portland arithmetic stress task.

Science.gov (United States)

Atchley, Rachel; Ellingson, Roger; Klee, Daniel; Memmott, Tabatha; Oken, Barry

2017-05-01

In this experiment, we developed and evaluated the Portland Arithmetic Stress Task (PAST) as a cognitive stressor to evaluate acute and sustained stress reactivity for event-related potential (ERP) studies. The PAST is a titrated arithmetic task adapted from the Montreal Imaging Stress Task (MIST), with added experimental control over presentation parameters, improved and synchronized acoustic feedback and generation of timing markers needed for physiological analyzes of real-time brain activity. Thirty-one older adults (M = 60 years) completed the PAST. EEG was recorded to assess feedback-related negativity (FRN) and the magnitude of the stress response through autonomic nervous system activity and salivary cortisol. Physiological measures other than EEG included heart rate, respiration rate, heart rate variability, blood pressure and salivary cortisol. These measures were collected at several time points throughout the task. Feedback-related negativity evoked-potential responses were elicited and they significantly differed depending on whether positive or negative feedback was received. The PAST also increased systolic blood pressure, heart rate variability and respiration rates compared to a control condition attentional task. These preliminary results suggest that the PAST is an effective cognitive stressor. Successful measurement of the feedback-related negativity suggests that the PAST is conducive to EEG and time-sensitive ERP experiments. Moreover, the physiological findings support the PAST as a potent method for inducing stress in older adult participants. Further research is needed to confirm these results, but the PAST shows promise as a tool for cognitive stress induction for time-locked event-related potential experiments.

Design and manufacture of Portland cement - application of sensitivity analysis in exploration and optimisation Part II. Optimisation

DEFF Research Database (Denmark)

Svinning, K.; Høskuldsson, Agnar

2006-01-01

A program for a model-based optimisation has been developed. The program contains two subprograms. The first one does minimising or maximising constrained by one original PLS-component or one equal to a combination of several. The second one does searching for the optimal combination of PLS-compo......-components, which gives max or min y. The program has proved to be applicable for achieving realistic results for implementation in the design of Portland cement with respect to performance and in the quality control during production....

How to Find Out in: Food Science.

Science.gov (United States)

Maine Univ., Orono. Raymond H. Fogler Library.

This library handbook is a guide for the student of food science. It lists some of the more useful materials and reference books basic to general research and gives their location in the Fogler Library at the University of Maine. Materials are listed in six categories: (1) dictionaries and encyclopedias, (2) U.S. and international documents, (3)…

Effect of mixes made of coal bottom ash and fly ash on the mechanical strength and porosity of Portland cement

Directory of Open Access Journals (Sweden)

Argiz, C.

2013-03-01

Full Text Available New additions to the cement are needed to achieve a more sustainable and durable construction material. Within this context, bottom ashes can be used as a main constituent of Portland cements when it is mixed in an optimized proportion with fly ashes. The mechanical characteristics of standarized mortars made of mixes of pulverized coal combustion bottom and fly ashes are studied. The mortars were made of ordinary Portland cement (CEM I 42.5 N and mixes of bottom ashes with fly ashes in similar proportions to those of CEM II/A-V, CEM II/B-V and CEM IV/A (V. Summing up, it can be said that the utilization of bottom ashes mixed with fly ashes in replacement levels from 0% to 100% do not affect significantively on the mechanical caracteristics of the mortars considered in the present study which had an addition maximum content of 35%.

La utilización de nuevas adiciones en el cemento es necesaria con el fin de obtener un material más sostenible y durable. En este sentido, las cenizas de fondo o cenicero de las centrales termoeléctricas de carbón se podrían reciclar siendo empleadas como un componente principal de los cementos Portland. Se han estudiado las propiedades mecánicas de unos morteros normalizados elaborados con mezclas de cenizas volantes con cenizas de fondo fabricados con unos porcentajes similares a los correspondientes de los CEM II/A-V, CEM II/B-V y CEM IV/A (V. En conclusión, la utilización de mezclas de cenizas de fondo o cenicero con cenizas volantes sustituyendo a éstas últimas entre el 0% y el 100%, no influye significativamente en el comportamiento mecánico de los morteros estudiados en los que el contenido máximo de adición ha sido del 35%, si bien afecta a determinados aspectos microestructurales, como la cantidad y distribución de poros capilares.

Avaliação preliminar do emprego de arenito zeolítico da região nordeste do Brasil como material pozolânico para cimento Portland Preliminary evaluation of sandstones from northeastern Brazil with pozzolanic properties for Portland cement

Directory of Open Access Journals (Sweden)

M. S. Picanço

2011-12-01

Full Text Available As zeolitas possuem atividade pozolânica normalmente sem a necessidade de ativação térmica, por isto têm sido empregadas na produção de cimento e concreto hidráulicos desde a época do império romano. Hoje em dia são utilizadas na fabricação do cimento Portland através da substituição do clinquer em percentuais que variam entre 5 e 20%, dependendo da reatividade e da finura da zeólita. Em razão disto, são muito importantes do ponto de vista econômico e ambiental, principalmente quando não necessitam de tratamento térmico para adquirirem caráter pozolânico satisfatório, porque reduzem significativamente a energia de produção do clinquer e a liberação de CO2 proveniente tanto da descarbonatação da calcita como da combustão de combustíveis fósseis. Contudo, dados sobre reservas de zeólitas naturais são escassos e imprecisos. No Brasil, não existe conhecimento sobre depósitos naturais de zeólitas que possam ser explorados comercialmente. No nordeste do Brasil existe a ocorrência de zeolitas sedimentares relacionadas a arenitos descoberta nos anos 2000. Estes arenitos são constituídos de quartzo, argilominerais e zeolitas naturais (estilbita. O objetivo geral desse trabalho foi avaliar se esta zeólita natural presente no arenito possui atividade pozolânica satisfatória para ser empregada como adição mineral em cimentos Portland. No programa experimental o arenito zeolítico passou por beneficiamento através da remoção, por peneiramento, do quartzo e outros minerais inertes, de modo a concentrar a zeólita estilbita e com isto verificar as propriedades pozolânicas deste mineral. No estudo experimental foram empregadas as técnicas de difração de raios X, calorimetria, ensaios químicos e de determinação da atividade pozolânica em argamassas de cal hidratada e cimento Portland. Os resultados mostraram que o arenito zeolítico acelerou a hidratação do cimento Portland devido a extrema finura do

Airway Science curriculum demonstration project : summary of initial evaluation findings.

Science.gov (United States)

1988-10-01

The performance, perceptions, and characteristics of Airway Science hires were compared with those of traditional hires. As of May 12, 1987. a total of 197 Airway Science candidates had been selected into FAA occupations. The demographic characterist...

Symmetry or asymmetry -- Comfort is the question. (A study of the second floor of the west office wing of the Water Pollution Control Laboratory in Portland, Oregon.)

Energy Technology Data Exchange (ETDEWEB)

Gonzalez, A.F.; Gaba, P.; Kowitanupong, C.

1999-07-01

This article explores the effects of an asymmetric distribution of building components, and their relation to human comfort. The studied building was the Water Pollution Control Laboratory in Portland, Oregon. This project, designed by the Miller/Hull Partnership, provides the perfect conditions to do such a study since it has very different ceiling heights within the same space, and an asymmetric distribution of the fenestration as well. Findings show that: (a) Variable ceiling heights affect the quantity of daylight received, and also affect the quality and distribution of electric light; (b) An asymmetric distribution of the fenestration creates very different conditions in both the luminous and thermal environments; and (c) The design of lighting and HVAC systems must take into consideration variations in ceiling height and the position of the fenestration into the space.

Avaliação de pastas de cimento Portland contendo cinza pesada moída

OpenAIRE

Pilar, Ronaldo; Schankoski, Rudiele Aparecida; Moro, Agostinho João Dal; Repette, Wellington Longuini

2016-01-01

Neste trabalho avalia-se a influência da incorporação de cinza pesada moída, obtida da combustão de carvão mineral, em pastas de cimento Portland. A cinza pesada foi incorporada as pastas de cimento em três distribuições granulométricas distintas e dosadas para teores de substituição ao cimento, em volume, de 10%, 30% e 50%. As pastas foram dosadas com duas relações água/aglomerante, em massa, de 0,35 e 0,40. As primeiras idades foram investigadas por calorimetria isotérmica. Após passarem po...

Preparation of composites of national rubber latex (NRL) - portland cement mould. Vol. 3

International Nuclear Information System (INIS)

Dessouki, A.M.; Taher, N.H.; El-Nahas, H.H.

1996-01-01

The aim of this study is to prepare some polymeric mould using national rubber latex (NRL) - portland cement composites based on a delayed- action mechanism. Factors affecting the preparation process such as concentration, mixing percentage, additives and their effect on what is regarded as a delayed action coacervant combination was studied. Composites of national latex (NRL) - portland cement would were prepared as two separate parts. The stabilized natural rubber latex (NRL) 100 parts with hydroxy ethyl cellulose (HEC) 2 parts as stabilizer and a delayed - action coacervant (sodium meta silicate as a delaying agent) 5 parts on one hand and the dry blend of cement 65 parts soluble in 65 parts of water as a paste on the other hand were mixed thoroughly on site. (HEC) was added to the rubber latex to prevent the coagulation of the rubber latex with the electrolyte (sodium meta silicate) present in the rubber mixture. Two kinds of stabilization occurred in the rubber part, namely steric stabilization and the stabilization against electrolyte. The effect of delayed - action coacervant (sodium meta silicate) on the initial setting time of rubber - cement mould showed that the molding process did not occur at sodium meta silicate concentration less than 2.66 parts per 100 parts of rubber latex (phr), and the optimum concentration used was 5% parts of rubber latex. It was observed that addition of a delaying agent (Sodium meta silicate) to the rubber part enhanced the delaying mechanism in the time needed for the molding process, while the addition of the delaying agent to the cement part did not have any effect on retardation of the molding process. Chemical coacervants function mainly by reducing the ζ potential which is associated with the electrical double layer surrounding the latex particle. This reduction may brought about in at least three distinct ways which take place in the system studied. 5 figs., 3 tabs

Preparation of composites of national rubber latex (NRL) - portland cement mould. Vol. 3

Energy Technology Data Exchange (ETDEWEB)

Dessouki, A M; Taher, N H; El-Nahas, H H [National Center for Radiation Research and Technology, Atomic Energy Athority, Cairo (Egypt)

1996-03-01

The aim of this study is to prepare some polymeric mould using national rubber latex (NRL) - portland cement composites based on a delayed- action mechanism. Factors affecting the preparation process such as concentration, mixing percentage, additives and their effect on what is regarded as a delayed action coacervant combination was studied. Composites of national latex (NRL) - portland cement would were prepared as two separate parts. The stabilized natural rubber latex (NRL) 100 parts with hydroxy ethyl cellulose (HEC) 2 parts as stabilizer and a delayed - action coacervant (sodium meta silicate as a delaying agent) 5 parts on one hand and the dry blend of cement 65 parts soluble in 65 parts of water as a paste on the other hand were mixed thoroughly on site. (HEC) was added to the rubber latex to prevent the coagulation of the rubber latex with the electrolyte (sodium meta silicate) present in the rubber mixture. Two kinds of stabilization occurred in the rubber part, namely steric stabilization and the stabilization against electrolyte. The effect of delayed - action coacervant (sodium meta silicate) on the initial setting time of rubber - cement mould showed that the molding process did not occur at sodium meta silicate concentration less than 2.66 parts per 100 parts of rubber latex (phr), and the optimum concentration used was 5% parts of rubber latex. It was observed that addition of a delaying agent (Sodium meta silicate) to the rubber part enhanced the delaying mechanism in the time needed for the molding process, while the addition of the delaying agent to the cement part did not have any effect on retardation of the molding process. Chemical coacervants function mainly by reducing the {zeta} potential which is associated with the electrical double layer surrounding the latex particle. This reduction may brought about in at least three distinct ways which take place in the system studied. 5 figs., 3 tabs.

Mobile Monitoring of Diesel Particulate Matter Exposure within Five Urban Microenvironments, Portland, OR

Science.gov (United States)

Orlando, P. J.; Bennett, B. A.; George, L. A.

2016-12-01

Diesel particulate matter (DPM) is a hazardous air pollutant linked to mortality and morbidity outcomes including cancer, cardiovascular disease, and adverse respiratory effects. The EPA's Air Toxics Assessment indicated that more than 50% of Oregonians are exposed to 10 times the ambient benchmark concentration (ABC) of 0.1 μgm-3 for DPM. These model estimates have not been verified with measurements, potentially limiting policy action. We developed a mobile monitoring platform to ground-truth model predictions and characterize DPM spatial variation. Using black carbon (BC) as a marker, concentrations within five urban microenvironments (a construction site, an arterial, a bus mall, a city park, and an indoor workspace) were sampled within Portland, OR. The mobile monitoring platform consisted of a bicycle and trailer equipped with an aethalometer measuring BC mass, a Data Ram 4 measuring total PM2.5 mass, and a Q-Starz GPS recording location; each instrument was monitoring in 1 second intervals. Concentrations of BC were used as an indicator of DPM. The construction site had the highest DPM concentration (7 μg m-3). The indoor workspace and the park had the lowest DPM (0.3 μg m-3). Near the construction site, DPM constituted approximately 50% of the total PM2.5. However, at the park, DPM was attributed to only 6% of the total PM2.5, while the indoor space constituted 15%. Concentrations of BC near construction sites were observed to exceed 67 times the state ABC of 0.1 μg m-3 (Figure). These results signify the need to better characterize the urban exposure to DPM, as even the cleanest microenvironments may be 3 times above the ABC. Our mobile monitoring platform will help further elucidate how local-scale sources contribute to the broader distribution of DPM within Portland, while providing a tool for both residents and DEQ to effectively mitigate the health impacts from DPM exposure.

Evaluation of bacterial leakage of four root- end filling materials: Gray Pro Root MTA, White Pro Root MTA, Root MTA and Portland Cement (type I

Directory of Open Access Journals (Sweden)

Zarabian M.

2005-07-01

Full Text Available Background and Aim: Today several materials have been used for root- end filling in endodontic surgery. Optimal properties of Pro Root MTA in in-vitro and in-vivo studies has been proven. On the other hand, based on some studies, Root MTA (Iranian Pro Root MTA and Portland cement are similar to Pro Root MTA in physical and biologic properties. The aim of this study was to evaluate bacterial leakage (amount and mean leakage time of four root- end filling materials. Materials and Methods: In this experimental in-vitro study, seventy six extracted single- rooted human teeth were randomly divided into six groups for root-end filling with gray Pro Root MTA, white Pro Root MTA, Root MTA (Iranian Pro Root MTA, Portland Cement (type I and positive and negative control groups. Root canals were instrumented using the step- back technique. Root- end filling materials were placed in 3mm ultra sonic retro preparations. Samples and microleakage model system were sterilized in autoclave. The apical 3-4 mm of the roots were immersed in phenol red with 3% lactose broth culture medium. The coronal access of each specimen was inoculated every 24h with a suspension of Streptococcus sanguis (ATCC 10556. Culture media were observed every 24h for colour change indicating bacterial contamination for 60 days. Statistical analysis was performed using log- rank test with P<0.05 as the limit of significance. Results: At the end of study 50%, 56.25%, 56.25% and 50% of specimens filled with Gray Pro Root MTA, White Pro Root MTA. Root MTA and Portland Cement (type I had evidence of leakage respectively. The mean leakage time was 37.19±6.29, 36.44±5.81, 37.69±5.97 and 34.81±6.67 days respectively. Statistical analysis of data showed no significant difference among the leakage (amount and mean leakage time of the four tested root- end filling materials (P=0.9958. Conclusion: Based on the results of this study, there were no significant differences in leakage among the four

EFFECT OF SEA WATER ON THE STRENGTH OF POROUS CONCRETE CONTAINING PORTLAND COMPOSITE CEMENT AND MICROFILAMENT POLYPROPYLENE FIBER

OpenAIRE

TJARONGE, M.W

2011-01-01

The aim of this research is to study the influence of sea water on the strength of porous concrete containing Portland Composite cement and micro monofilament polypropylene fibre. The specimens of porous concrete were immersed in the sea water up to 28 days. The compressive strength test and flexural strength test were carried out at 3, 7 and 28 days in order to investigate the strength development. The test result indicated that the strength of porous concrete can develop in t...

Prediction of water vapour sorption isotherms and microstructure of hardened Portland cement pastes

International Nuclear Information System (INIS)

Burgh, James M. de; Foster, Stephen J.; Valipour, Hamid R.

2016-01-01

Water vapour sorption isotherms of cementitious materials reflect the multi-scale physical microstructure through its interaction with moisture. Our ability to understand and predict adsorption and desorption behaviour is essential in the application of modern performance-based approaches to durability analysis, along with many other areas of hygro-mechanical and hygro-chemo-mechanical behaviour. In this paper, a new physically based model for predicting water vapour sorption isotherms of arbitrary hardened Portland cement pastes is presented. Established thermodynamic principles, applied to a microstructure model that develops with hydration, provide a rational basis for predictions. Closed-form differentiable equations, along with a rational consideration of hysteresis and scanning phenomena, makes the model suitable for use in numerical moisture simulations. The microstructure model is reconciled with recently published 1 H NMR and mercury intrusion porosimetry results.

Exploiting multimedia in reproductive science education: research findings.

Science.gov (United States)

Senger, P L; Oki, A C; Trevisan, M S; McLean, D J

2012-08-01

Education in reproductive science is operating from an outdated paradigm of teaching and learning. Traditionally, reproductive education follows the pattern where students read a textbook, listen to instructor presentations, re-read the textbook and class notes and then complete a test. This paradigm is inefficient, costly and has not incorporated the potential that technology can offer with respect to increases in student learning. Further, teachers of reproductive science (and all of science for that matter) have little training in the use of documented methods of instructional design and cognitive psychology. Thus, most of us have learned to teach by repeating the approaches our mentors used (both good and bad). The technology now exists to explain complex topics using multimedia presentations in which digital animation and three-dimensional anatomical reconstructions greatly reduce time required for delivery while at the same time improving student understanding. With funding from the Small Business Innovation Research program through the U.S. Department of Education, we have developed and tested a multimedia approach to teaching complex concepts in reproductive physiology. The results of five separate experiments involving 1058 university students and 122 patients in an OB/GYN clinic indicate that students and patients learned as much or more in less time when viewing the multimedia presentations when compared to traditional teaching methodologies. © 2012 Blackwell Verlag GmbH.

Physical chemistry of portland-cement hydrate, radioactive-waste hosts: Final report, January 16, 1987--December 31, 1987

International Nuclear Information System (INIS)

Grutzeck, M.W.

1989-01-01

This is a final report summarizing the results of a study of the physical and crystal chemistry of potential hydroxylated radioactive waste hosts compatible with portland cement. Research has focussed on the identification and evaluation of hydrated host phases for four ions: cesium, strontium, iodine and boron. These ions were chosen because they are among the most long lived of the radioactive waste ions as well as the most difficult to immobilize with cement-based materials. Results show that such phases do indeed exist, and that they are excellent host phases for the above ions

Analysis by X-Ray images of EVA waste incorporated in Portland Cement

International Nuclear Information System (INIS)

Marques, M.A.; Antunes, M.L.P.; Montagnoli, R.M.; Mancini, S.D.

2012-01-01

The EVA is a copolymer used by Brazilian shoes industries. This material is cut for the manufacture of insoles. This operation generates about 18% of waste. The EVA waste can be reused in incorporation in Portland cement to construction without structural purposes. The aim of this work is to show X-rays images to assessment the space distribution of the wastes in the cement and to evaluate the use of this methodology. Cylindrical specimens were produced according to ABNT - NBR 5738 standards. The volume relation of sand and cement was 3:1, 10% and 30% of waste was incorporated in cement specimens. X-Rays images were obtained of cylindrical specimens in front projection. The images showed that the distribution of the waste is homogeneous, consistent with what was intended in this type of incorporation, which can provide uniformity in test results of compressive strength. (author)

Increasing the compressive strength of portland cement concrete using flat glass powder

Energy Technology Data Exchange (ETDEWEB)

Miranda Junior, Edson Jansen Pedrosa de; Bezerra, Helton de Jesus Costa Leite; Politi, Flavio Salgado; Paiva, Antonio Ernandes Macedo, E-mail: edson.jansen@ifma.edu.br [Instituto Federal de Educacao, Ciencia e Tecnologia do Maranha (IFMA), Sao Luis, MA (Brazil). Dept. de Mecanica e Materiais

2014-08-15

This paper analyzes the compressive strength of Portland cement concrete in response to the incorporation of 5%, 10% and 20% of flat glass powder in place of sand, at w/c (water/cement) ratios of 0.50, 0.55 and 0.58. A statistical analysis of variance (ANOVA) was performed after 7, 14 and 28 days of curing. The compressive strength test results indicate that the concrete containing a w/c ratio of 0.50 can be used for structural applications, regardless of the waste glass content, as can that with a w/c ratio of 0.55 containing 20% of waste glass. We suggest that the use of flat glass powder in place of sand in the above mentioned percentages is feasible for the production of an environmentally appropriate and structurally applicable concrete. However, the concrete's fluidity and void content must be taken into account. (author)

Corrosion rate of steel embedded in blended Portland and fluid catalytic cracking catalyst residue (FC3R cement mortars

Directory of Open Access Journals (Sweden)

Payá, J.

2008-12-01

Full Text Available This paper reports on a study of the corrosion levels in steel bars embedded in mortars made with a blend of Portland cement and (0-20% spent fluid catalytic cracking catalyst residue (FC3R, with a variable (0.3-0.7 water/binder (w/b ratio. The specimens were stored in the following conditions: relative humidity of 40, 80 or 100% and CO2 concentrations of 5 and 100%. The steel corrosion rate was measured with polarization resistance techniques. In the absence of aggressive agents, the steel was found to remain duly passivated in mortars with an FC3R content of up to 15% under all the conditions of relative humidity tested. The reinforcement corrosion level in mortars with a w/b ratio of 0.3 and 15% FC3R subjected to accelerated carbonation was similar to the level observed in the unblended Portland cement control mortar.En este trabajo se ha estudiado el nivel de corrosión de barras de acero embebidas en morteros de cemento Portland con relación agua/material cementante (a/mc variable (0,3-0,7, en los que parte del cemento (0-20% se sustituyó por catalizador de craqueo usado (FC3R. Las condiciones de conservación de las probetas elaboradas fueron las siguientes: distintas humedades relativas (40, 80 y 100% y dos concentraciones de CO2 (5 y 100%. La velocidad de corrosión de los aceros se midió mediante la técnica de resistencia de polarización. Se ha podido determinar que, bajo las distintas condiciones de humedad relativa y ausencia de agresivo, los aceros se mantuvieron correctamente pasivados en los morteros con contenidos de FC3R de hasta el 15%. El nivel de corrosión que presenta el refuerzo embebidos en morteros con sustitución de un 15% de cemento por FC3R y relación a/mc 0,3, al ser sometidos a un proceso de carbonatación acelerada, era muy similar al mostrado por el mortero patrón, sin FC3R.

Push-out strength of modified Portland cements and resins.

Science.gov (United States)

Iacono, Francesco; Gandolfi, Maria Giovanna; Huffman, Bradford; Sword, Jeremy; Agee, Kelli; Siboni, Francesco; Tay, Franklin; Prati, Carlo; Pashley, David

2010-02-01

Modified calcium-silicate cements derived from white Portland cement (PC) were formulated to test their push-out strength from radicular dentin after immersion for 1 month. Slabs obtained from 42 single-rooted extracted teeth were prepared with 0.6 mm diameter holes, then enlarged with rotary instruments. After immersion in EDTA and NaOC1, the holes were filled with modified PCs or ProRoot MTA, Vitrebond and Clearfil SE. Different concentrations of phyllosilicate (montmorillonite-MMT) were added to experimental cements. ProRoot MTA was also included as reference material. Vitrebond and Clearfil SE were included as controls. Each group was tested after 1 month of immersion in water or PBS. A thin-slice push-out test on a universal testing machine served to test the push-out strength of materials. Results were statistically analyzed using the least squares means (LSM) method. The modified PCs had push-out strengths of 3-9.5 MPa after 1 month of immersion in water, while ProRoot MTA had 4.8 MPa. The push-out strength of PC fell after incubation in PBS for 1 month, while the push-out strength of ProRoot MTA increased. There were no significant changes in Clearfil SE Bond or Vitrebond after water or PBS storage.

Influence of citric acid as setting retarder in CPV portland cement pastes and mortars

International Nuclear Information System (INIS)

Mendes, B.C.; Lopes, M.M.S.; Alvarenga, R.C.S.S.; Fassoni, D.P.; Pedroti, L.G.; Azevedo, A.R.G. de

2016-01-01

This work aims to study the availability of using and the influence of citric acid in the properties of pastes and mortars made with Portland cement CPV ARI both in fresh and hardened form. The citric acid dosages were 0, 0.4%, and 0.8% relative to the cement mass. The produced cement pastes were tested to determine normal consistency water and initial and final setting times. Mortars were tested to determine the consistency index, specific gravity, air entrained content in the fresh stage, hardened bulk density, compressive strength at ages 7, 14, and 28 days, and analysis by XRD technique. The results show that citric acid, besides improve the mortar workability, contribute to an increase in mechanical strength in older than 14 days. (author)

Effect of water curing duration on strength behaviour of portland composite cement (PCC) mortar

Science.gov (United States)

Caronge, M. A.; Tjaronge, M. W.; Hamada, H.; Irmawaty, R.

2017-11-01

Cement manufacturing of Indonesia has been introduced Portland Composite Cement (PCC) to minimize the rising production cost of cement which contains 80% clinker and 20% mineral admixture. A proper curing is very important when the cement contains mineral admixture materials. This paper reports the results of an experimental study conducted to evaluate the effect of water curing duration on strength behaviour of PCC mortar. Mortar specimens with water to cement ratio of (W/C) 0.5 were casted. Compressive strength, flexural strength and concrete resistance were tested at 7, 28 and 91 days cured water. The results indicated that water curing duration is essential to continue the pozzolanic reaction in mortar which contributes to the development of strength of mortar made with PCC.

Plant-Wide Energy Efficiency Assessment at the Arizona Portland Cement Plant in Rillito, Arizona

Energy Technology Data Exchange (ETDEWEB)

Stephen J. Coppinger, P.E.; Bruce Colburn, Ph.D., P.E., CEM

2007-05-17

A Department of Energy Plant-wide Assessment was undertaken by Arizona Portland Cement (APC) beginning in May 2005. The assessment was performed at APC’s cement production facility in Rillito, Arizona. The assessment included a compressed air evaluation along with a detailed process audit of plant operations and equipment. The purpose of this Energy Survey was to identify a series of energy cost savings opportunities at the Plant, and provide preliminary cost and savings estimates for the work. The assessment was successful in identifying projects that could provide annual savings of over $2.7 million at an estimated capital cost of $4.3 million. If implemented, these projects could amount to a savings of over 4.9 million kWh/yr and 384,420 MMBtu/year.

Science teacher’s idea about environmental concepts in science learning as the first step of science teacher training

Science.gov (United States)

Tapilouw, M. C.; Firman, H.; Redjeki, S.; Chandra, D. T.

2018-05-01

To refresh natural environmental concepts in science, science teacher have to attend a teacher training. In teacher training, all participant can have a good sharing and discussion with other science teacher. This study is the first step of science teacher training program held by education foundation in Bandung and attended by 20 science teacher from 18 Junior High School. The major aim of this study is gathering science teacher’s idea of environmental concepts. The core of questions used in this study are basic competencies linked with environmental concepts, environmental concepts that difficult to explain, the action to overcome difficulties and references in teaching environmental concepts. There are four major findings in this study. First finding, most environmental concepts are taught in 7th grade. Second finding, most difficult environmental concepts are found in 7th grade. Third finding, there are five actions to overcome difficulties. Fourth finding, science teacher use at least four references in mastering environmental concepts. After all, teacher training can be a solution to reduce difficulties in teaching environmental concepts.

Evaluation of physical stability and leachability of Portland Pozzolona Cement (PPC) solidified chemical sludge generated from textile wastewater treatment plants

International Nuclear Information System (INIS)

Patel, Hema; Pandey, Suneel

2012-01-01

Highlights: ► Stabilization/solidification of chemical sludge from textile wastewater treatment plants using Portland Pozzolona Cement (PPC) containing fly ash. ► Physical engineering (compressive strength and block density) indicates that sludge has potential to be reused for construction purpose after stabilization/solidification. ► Leaching of heavy metals from stabilized/solidified materials were within stipulated limits. ► There is a modification of microstructural properties of PPC with sludge addition as indicated by XRD and SEM patterns. - Abstract: The chemical sludge generated from the treatment of textile dyeing wastewater is a hazardous waste as per Indian Hazardous Waste Management rules. In this paper, stabilization/solidification of chemical sludge was carried out to explore its reuse potential in the construction materials. Portland Pozzolona Cement (PPC) was selected as the binder system which is commercially available cement with 10–25% fly ash interground in it. The stabilized/solidified blocks were evaluated in terms of unconfined compressive strength, block density and leaching of heavy metals. The compressive strength (3.62–33.62 MPa) and block density (1222.17–1688.72 kg/m 3 ) values as well as the negligible leaching of heavy metals from the stabilized/solidified blocks indicate that there is a potential of its use for structural and non-structural applications.

Portland cement induces human periodontal ligament cells to differentiate by upregulating miR-146a

Directory of Open Access Journals (Sweden)

Min-Ching Wang

2018-04-01

Full Text Available Background/Purpose: Bioaggregates such as Portland cement (PC can be an economical alternative for mineral trioxide aggregate (MTA with additional benefit of less discoloration. MTA has been known to induce differentiations of several dental cells. MicroRNAs are important regulators of biological processes, including differentiation, physiologic homeostasis, and disease progression. This study is to explore how PC enhances the differentiation of periodontal ligament (PDL cells in microRNAs level. Methods: PDL cells were cultured in a regular PC- or MTA-conditioned medium or an osteoinduction medium (OIM. Alizarin red staining was used to evaluate the extent of mineralization. Transfection of microRNA mimics induced exogenous miR-31 and miR-146a expression. The expression of microRNAs and differentiation markers was assayed using reverse-transcriptase polymerase chain reaction. Results: PC enhanced the mineralization of PDL cells in a dose-dependent manner in the OIM. Exogenous miR-31 and miR-146a expression upregulated alkaline phosphatase (ALP, bone morphogenic protein (BMP, and dentin matrix protein 1 (DMP1 expression. However, miR-31 and miR-146a modulates cementum protein 1 (CEMP1 expression in different ways. PC also enhanced ALP and BMP but attenuated CEMP1 in the OIM. Although the OIM or PC treatment upregulated miR-21, miR-29b, and miR-146a, only miR-146a was able to be induced by PC in combination with OIM. Conclusion: This study demonstrated that PC enhances the differentiation of PDL cells, especially osteogenic through miR-146a upregulation. In order to control the ankylosis after regenerative endodontics with the usage of bioaggregates, further investigations to explore these differentiation mechanisms in the miRNA level may be needed. Keywords: Portland cement, Bioaggregate, miR-146a, Osteogenic differentiation, Periodontal ligament (PDL

76 FR 19661 - Response to Petition From New Jersey Regarding SO2

Science.gov (United States)

2011-04-07

...In this action, EPA proposes to make a finding that the coal- fired Portland Generating Station (Portland Plant) in Upper Mount Bethel Township, Northampton County, Pennsylvania, is emitting air pollutants in violation of the interstate transport provisions of the Clean Air Act (CAA or Act). Specifically, EPA is proposing to find that emissions of sulfur dioxide (SO2) from the Portland Plant significantly contribute to nonattainment and interfere with maintenance of the 1-hour SO2 national ambient air quality standard (NAAQS) in New Jersey. This finding is proposed in response to a petition submitted by the State of New Jersey Department of Environmental Protection (NJDEP) on September 17, 2010. In this action, EPA is also proposing emission limitations and compliance schedules to ensure that the Portland Plant will no longer significantly contribute to nonattainment, and no longer interfere with maintenance of the 1- hour SO2 NAAQS, thereby permitting continued operation of the Portland Plant beyond the 3-month limit established by the CAA for sources subject to such a finding.

Assessment the potential of using Carbon nanotubes reinforcements for improving the tensile/flexural strength and fracture toughness of Portland cement paste for damage resistant concrete transportation infrastructures.

Science.gov (United States)

2010-09-01

The focus of this study was on exploring the use of nanotechnology-based nano-filaments, such as carbon : nanotubes (CNTs) and nanofibers (CNFs), as reinforcement in improving the mechanical properties of Portland : cement paste as a construction mat...

Performance of portland limestone cements: Cements designed to be more sustainable that include up to 15% limestone addition

Science.gov (United States)

Barrett, Timothy J.

In 2009, ASTM and AASHTO permitted the use of up to 5% interground limestone in ordinary portland cement (OPC) as a part of a change to ASTM C150/AASHTO M85. When this work was initiated a new proposal was being discussed that would enable up to 15% interground limestone cement to be considered in ASTM C595/AASHTO M234. This work served to provide rapid feedback to the state department of transportation and concrete industry for use in discussions regarding these specifications. Since the time this work was initiated, ASTM C595/AASHTO M234 was passed (2012c) and PLCs are now able to be specified, however they are still not widely used. The proposal for increasing the volume of limestone that would be permitted to be interground in cement is designed to enable more sustainable construction, which may significantly reduce the CO2 that is embodied in the built infrastructure while also extending the life of cement quarries. Research regarding the performance of cements with interground limestone has been conducted by the cement industry since these cements became widely used in Europe over three decades ago, however this work focuses on North American Portland Limestone Cements (PLCs) which are specifically designed to achieve similar performance as the OPCs they replace.This thesis presents a two-phase study in which the potential for application of cements containing limestone was assessed. The first phase of this study utilized a fundamental approach to determine whether cement with up to 15% of interground or blended limestone can be used as a direct substitute to ordinary portland cement. The second phase of the study assessed the concern of early age shrinkage and cracking potential when using PLCs, as these cements are typically ground finer than their OPC counterparts. For the first phase of the study, three commercially produced PLCs were obtained and compared to three commercially produced OPCs made from the same clinker. An additional cement was tested

Acompanhamento da hidratação de cimento Portland simples com resíduo de bauxita

Directory of Open Access Journals (Sweden)

R. C. O. Romano

Full Text Available Resumo A substituição parcial de cimento Portland por resíduo de bauxita (RB resulta em produtos com, no mínimo, propriedades similares às dos produtos fabricados com o ligante puro. No entanto, as interações físico-químicas entre os diferentes tipos de cimento e o RB durante a reação de hidratação ainda é pouco explorada em literatura. A elevada quantidade de sódio e a presença de Al2O3, SiO2 e Fe2O3 são fatores que afetam a formação dos produtos hidratados e dependem do tipo de cimento utilizado na mistura. Sendo assim, este trabalho foi realizado com o objetivo de avaliar o impacto da presença do resíduo de bauxita em associação ao cimento Portland simples nas primeiras idades de hidratação. Calorimetria de condução isotérmica, difração de raios X, análise termogravimétrica e espectroscopia de infravermelho foram as técnicas escolhidas para o monitoramento. Os resultados ilustraram que a presença do resíduo coletado na planta da Alcoa (Poços de Caldas aumenta o tempo de indução, o consumo de portlandita, e as quantidades de etringita e monossulfoaluminato formadas. Ao mesmo tempo, houve formação de silicoaluminato de sódio e bicarbonato de sódio, devido às reações com silicatos, aluminatos e com o carbonato do cimento.

Blasted copper slag as fine aggregate in Portland cement concrete.

Science.gov (United States)

Dos Anjos, M A G; Sales, A T C; Andrade, N

2017-07-01

The present work focuses on assessing the viability of applying blasted copper slag, produced during abrasive blasting, as fine aggregate for Portland cement concrete manufacturing, resulting in an alternative and safe disposal method. Leaching assays showed no toxicity for this material. Concrete mixtures were produced, with high aggregate replacement ratios, varying from 0% to 100%. Axial compressive strength, diametrical compressive strength, elastic modulus, physical indexes and durability were evaluated. Assays showed a significant improvement in workability, with the increase in substitution of fine aggregate. With 80% of replacement, the concrete presented lower levels of water absorption capacity. Axial compressive strength and diametrical compressive strength decreased, with the increase of residue replacement content. The greatest reductions of compressive strength were found when the replacement was over 40%. For tensile strength by diametrical compression, the greatest reduction occurred for the concrete with 80% of replacement. After the accelerated aging, results of mechanic properties showed a small reduction of the concrete with blasted copper slag performance, when compared with the reference mixture. Results indicated that the blasted copper slag is a technically viable material for application as fine aggregate for concrete mixtures. Copyright © 2017 Elsevier Ltd. All rights reserved.

Can citizen science enhance public understanding of science?

Science.gov (United States)

Bonney, Rick; Phillips, Tina B; Ballard, Heidi L; Enck, Jody W

2016-01-01

Over the past 20 years, thousands of citizen science projects engaging millions of participants in collecting and/or processing data have sprung up around the world. Here we review documented outcomes from four categories of citizen science projects which are defined by the nature of the activities in which their participants engage - Data Collection, Data Processing, Curriculum-based, and Community Science. We find strong evidence that scientific outcomes of citizen science are well documented, particularly for Data Collection and Data Processing projects. We find limited but growing evidence that citizen science projects achieve participant gains in knowledge about science knowledge and process, increase public awareness of the diversity of scientific research, and provide deeper meaning to participants' hobbies. We also find some evidence that citizen science can contribute positively to social well-being by influencing the questions that are being addressed and by giving people a voice in local environmental decision making. While not all citizen science projects are intended to achieve a greater degree of public understanding of science, social change, or improved science -society relationships, those projects that do require effort and resources in four main categories: (1) project design, (2) outcomes measurement, (3) engagement of new audiences, and (4) new directions for research. © The Author(s) 2015.

A study of photon interaction in some building materials: High-volume admixture of blast furnace slag into Portland cement

International Nuclear Information System (INIS)

Kurudirek, Murat; Tuerkmen, Ibrahim; Ozdemir, Yueksel

2009-01-01

Total mass attenuation coefficients, mean free paths (MFP), half-value (HVT) and tenth-value (TVT) thicknesses of Portland cement and three mixtures have been calculated in function of the energy from 1 keV to 100 GeV. Both in the low- and high-energy region there were significant variations in those parameters where photoelectric process and pair production partially dominates, respectively. In general, the attenuation parameters were found to vary with chemical composition, density of given material and photon energy.

A study of photon interaction in some building materials: High-volume admixture of blast furnace slag into Portland cement

Energy Technology Data Exchange (ETDEWEB)

Kurudirek, Murat [Faculty of Science, Department of Physics, Ataturk University, 25240 Erzurum (Turkey)], E-mail: mkurudirek@gmail.com; Tuerkmen, Ibrahim [Faculty of Engineering, Department of Civil Engineering, Ataturk University, 25240 Erzurum (Turkey); Ozdemir, Yueksel [Faculty of Science, Department of Physics, Ataturk University, 25240 Erzurum (Turkey)

2009-09-15

Total mass attenuation coefficients, mean free paths (MFP), half-value (HVT) and tenth-value (TVT) thicknesses of Portland cement and three mixtures have been calculated in function of the energy from 1 keV to 100 GeV. Both in the low- and high-energy region there were significant variations in those parameters where photoelectric process and pair production partially dominates, respectively. In general, the attenuation parameters were found to vary with chemical composition, density of given material and photon energy.

Lime kiln dust as a potential raw material in portland cement manufacturing

Science.gov (United States)

Miller, M. Michael; Callaghan, Robert M.

2004-01-01

In the United States, the manufacture of portland cement involves burning in a rotary kiln a finely ground proportional mix of raw materials. The raw material mix provides the required chemical combination of calcium, silicon, aluminum, iron, and small amounts of other ingredients. The majority of calcium is supplied in the form of calcium carbonate usually from limestone. Other sources including waste materials or byproducts from other industries can be used to supply calcium (or lime, CaO), provided they have sufficiently high CaO content, have low magnesia content (less than 5 percent), and are competitive with limestone in terms of cost and adequacy of supply. In the United States, the lime industry produces large amounts of lime kiln dust (LKD), which is collected by dust control systems. This LKD may be a supplemental source of calcium for cement plants, if the lime and cement plants are located near enough to each other to make the arrangement economical.

Portland blended cements: demolition ceramic waste management; Cementos Portland con adiciones: manejo de residuos cerámicos de demolición.

Energy Technology Data Exchange (ETDEWEB)

Trezza, M.A.; Zito, S.; Tironi, A.; Irassar, E.F.; Rahhal, V.F.

2017-07-01

Demolition ceramic wastes (DCWs) were investigated in order to determine their potential use as supplementary cementitious materials in Portland Blended Cements (PBCs). For this purpose, three ceramic wastes were investigated. After characterization of the materials used, the effect of ceramic waste replacement (8, 24 and 40% by mass) was analyzed. Pozzolanic activity, hydration progress, workability and compressive strength were determined at 2, 7 and 28 days. The results showed that the ground wastes behave as filler at an early age, but as hydration progresses, the pozzolanic activity of ceramic waste contributes to the strength requirement. [Spanish] Se estudiaron residuos cerámicos de demolición (DCWs) a fin de determinar su potencial uso como materiales cementicios suplementarios en cementos mezcla (PBC). Para este propósito, se investigaron tres residuos cerámicos. Luego de la caracterización de los materiales a utilizar, se analizó el efecto del reemplazo por residuos cerámico (8, 24 y 40% en peso). Se estudió la actividad puzolánica, el progreso de la hidratación, la trabajabilidad y la resistencia a compresión a 2, 7 y 28 días. Los resultados mostraron que los residuos molidos se comportaron como fillers a edades tempranas, pero con el progreso de la hidratación, la actividad puzolánica de los residuos cerámicos contribuye a los requerimientos de resistencia.

Finding "Science" in the Archives of the Spanish Monarchy.

Science.gov (United States)

Portuondo, Maria M

2016-03-01

This essay explores the history of several archives that house the early modern records of Spanish imperial science. The modern "archival turn" urges us to think critically about archives and to recognize in the history of these collections an embedded, often implicit, history that--unless properly recognized, acknowledged, and understood--can distort the histories we are trying to tell. This essay uses a curious episode in the history of science to illustrate how Spanish archives relate to each other and shape the collections they house. During the late eighteenth century a young navy officer, Martín Fernández de Navarrete, was dispatched to all the principal archives of the Spanish monarchy with a peculiar mission: he was to search for evidence that the Spanish in fact had a scientific tradition. This essay uses his mission to explain how the original purpose of an archive--the archive's telos--may persist as a strong and potentially deterministic force in the work of historians of science. In the case of the archives discussed, this telos was shaped by issues as wide ranging as defending a nation's reputation against claims of colonial neglect and as idiosyncratic as an archivist's selection criteria.

Hands across the divide: Finding spaces for student-centered pedagogy in the undergraduate science classroom

Science.gov (United States)

Spier-Dance, Lesley

This study explored college science students' and instructors' experiences with student-generated and performed analogies. The objectives of the study were to determine whether the use of student-generated analogies could provide students with opportunities to develop robust understanding of difficult science concepts, and to examine students' and instructors' perspectives on the utilization of these analogies. To address my objectives, I carried out a case study at a university-college in British Columbia. I examined the use of analogies in undergraduate biology and chemistry courses. Working with three instructors, I explored the use of student-generated analogies in five courses. I carried out in-depth analyses for one biology case and one chemistry case. Data were collected using semi-structured interviews, classroom observations, researcher journal logs and students' responses to assessment questions. My findings suggest that involvement in the analogy exercise was associated with gains in students' conceptual understanding. Lower-achieving students who participated in the analogy activity exhibited significant gains in understanding of the science concept, but were unable to transfer their knowledge to novel situations. Higher-achieving students who participated in the activity were better able to transfer their knowledge of the analogy-related science topic to novel situations. This research revealed that students exhibited improved understanding when their analogies clearly represented important features of the target science concept. Students actively involved in the analogy activity exhibited gains in conceptual understanding. They perceived that embodied performative aspects of the activity promoted engagement, which motivated their learning. Participation in the analogy activity led to enhanced social interaction and a heightened sense of community within the classroom. The combination of social and performative elements provided motivational learning

Manganese substitutions into the portland cement clinker phases

Directory of Open Access Journals (Sweden)

Puertas, F.

1989-06-01

Full Text Available The effect of manganese substitution into the crystal structures of the main Portland cement clinker phases (3CaO.SiO₂, 2CaO.SiO₂, 3CaO.Al₂O₃, 2CaO.Fe₂O₃ y 4CaO.Al₂O₃.Fe₂O₃ has been studied by X-ray and analytical electron microscopy. In oxidizing conditions, the limit of solid solution in 3CaO.SiO₂ is about 0.72 ±0.11% (wt, while in 2CaO.SiO₂ is 1.53±0,12%(wt. Mn solid solubility on 3CaO.Al₂O₃structure, in oxidizing conditions is close to 0.78 ± 0,12% (wt. In identical atmosphere, the proportion of Mn in the ferrite phases (2CaO.Fe₂O₃ and 4CaO.Al₂O₃.Fe₂O₃ is 6.80 ± 0.87% (wt and 6.7% (wt, respectively. To each mentioned clinker phases a solid solution formula has been proposed. In these formula, the manganese substitutions and also the different oxidation states which this element can be introduced in those crystalline structure are defined.

Se ha estudiado, por difracción de rayos X y microanálisis por espectroscopia de energías dispersivas, el efecto de la sustitución del manganeso en las estructuras cristalinas de las fases más importantes del clinker del cemento portland (3CaO.SiO₂, 2CaO.SiO₂, 3CaO.Al₂O₃, 2CaO.Fe₂O₃ y 4CaO.Al₂O₃.Fe₂O₃. En condiciones oxidantes, el límite de solubilidad sólida en 3CaO.SiO₂ es del orden de 0,72 ± 0,11% en peso; mientras que en 2CaO.SiO₂ es de 1,53 ±0,12% en peso. La solución sólida del Mn en la estructura del 3CaO.Al₂O₃, en condiciones oxidantes, es próxima al 0,78 ±0,12% en peso. En idéntica atmósfera, la proporción del Mn en las fases terríficas (2CaO.Fe₂O₃ y 4CaO.Al₂

Finding the way forward for forensic science in the US-A commentary on the PCAST report.

Science.gov (United States)

Evett, I W; Berger, C E H; Buckleton, J S; Champod, C; Jackson, G

2017-09-01

A recent report by the US President's Council of Advisors on Science and Technology (PCAST), (2016) has made a number of recommendations for the future development of forensic science. Whereas we all agree that there is much need for change, we find that the PCAST report recommendations are founded on serious misunderstandings. We explain the traditional forensic paradigms of match and identification and the more recent foundation of the logical approach to evidence evaluation. This forms the groundwork for exposing many sources of confusion in the PCAST report. We explain how the notion of treating the scientist as a black box and the assignment of evidential weight through error rates is overly restrictive and misconceived. Our own view sees inferential logic, the development of calibrated knowledge and understanding of scientists as the core of the advance of the profession. Copyright © 2017 Elsevier B.V. All rights reserved.

Numerical simulation of heat and mass transport during hydration of Portland cement mortar in semi-adiabatic and steam curing conditions

OpenAIRE

Hernandez-Bautista, E.; Bentz, D. P.; Sandoval-Torres, S.; de Cano-Barrita, P. F. J.

2016-01-01

A model that describes hydration and heat-mass transport in Portland cement mortar during steam curing was developed. The hydration reactions are described by a maturity function that uses the equivalent age concept, coupled to a heat and mass balance. The thermal conductivity and specific heat of mortar with water-to-cement mass ratio of 0.30 was measured during hydration, using the Transient Plane Source method. The parameters for the maturity equation and the activation energy were obtaine...

Acción del agua de mar sobre un cemento portland de alta resistencia inicial y sobre un cemento portland resistente a los sulfatos: influencia de la adición de escoria. Estudio de la concentración iónica

Directory of Open Access Journals (Sweden)

Gaspar-Tébar, Demetrio

1987-06-01

Full Text Available Not available

En este trabajo se estudia la variación del pH, así como la de la concentración de los iones Ca (II, Mg (II, SO₄ (II y Cl (I del agua de mar artificial (ASTM D 1141-75, en donde las probetas de mortero (1 : 3 de 1 X 1 X 6 cm fabricadas con un cemento portland industrial de alta resistencia inicial (cemento 1, con un cemento portland industrial resistente a los sulfatos (cemento 2 y con las mezclas cemento (1 ó 2/escoria = 85/15, 65/35, 40/60 y 30/70 (en peso han estado sumergidas, durante 56 - 90 - 180 y 360 días, después del período de curado (1 día en cámara húmeda y 21 días en agua potable; así mismo se estudia la evolución del contenido de Ca (II, Mg (II y SO₄ (II en la nueva fase sólida formada en el agua de mar artificial mencionada en donde han estado las probetas de mortero. En el agua de mar artificial se produce un aumento de la concentración de Ca (II y del valor del pH, una disminución de las cantidades de Mg (II, SO₄ (II y Cl (I, así como la formación de una nueva fase sólida, que son función de las mezclas cemento/escoria utilizadas para elaborar las probetas de mortero y del tiempo de conservación-ataque. El contenido de Ca (II, que procede del Ca(0H₂ disuelto del cemento hidratado, en el agua de mar artificial responde, prácticamente, a las cantidades calculadas a partir del Ca (II correspondientes al medio (agua de mar artificial en donde han estado las probetas fabricadas con los dos cementos estudiados, sin adición de escoria. La evolución de los contenidos de Ca (II y de Mg (II en el agua de mar artificial, en donde han estado las probetas, están íntimamente ligados, de tal modo que si la concentración de uno de ellos aumenta, la del otro disminuye y viceversa. Hay un sistema cemento/escoria - agua de mar artificial, para una mezcla determinada, en donde tiene lugar el equilibrio Ca (II que pasa a la disolución ⇌ Mg (II que

Effectiveness of inorganic membrane mixture of natural zeolite and portland white cement in purifying of peat water based on turbidity parameter

Science.gov (United States)

Elfiana; Fuadi, A.; Diana, S.

2018-04-01

Peat water is water surface that brownish red colour caused by the contained constituents. Solving the peat watercolor problem requires special attention considering the quantity of peat water and suitable to be used to meet the daily needs. This study aims to know the inorganic membrane capability of mix nature zeolite and white Portland cement to purifying the peat water based on turbidity parameter. The study was conducted by varying the composition of nature zeolite (Za) and white Portland cement (Sp) in the ratio of Za: Sp is (25%:75%; 50%:50%; 75%:25%) with zeolite condition activated using HCl 2M and nonactivated zeolite treatments. The result of the characteristic test on membrane morphology using SEM (Scanning Electron Microscope) showed that the pore surface size of the membrane is 2 μm that could classified in microfiltration membrane an organic type. The characteristic test showed also resulted in the density of 0.77 to 0.86 gr/cm3, porosity 26.22% to 35.93%, and permeability 2736.19 to 8428.15. While the water retention capacity is in range of 30.64% to 46.46%, The result of inorganic membrane application on peat water showed turbidity of peat water decreased 94.17%, from 10.3 NTU to 0.6 NTU.

Chemical composition, effective atomic number and electron density study of trommel sieve waste (TSW), Portland cement, lime, pointing and their admixtures with TSW in different proportions

International Nuclear Information System (INIS)

Kurudirek, Murat; Aygun, Murat; Erzeneoglu, Salih Zeki

2010-01-01

The trommel sieve waste (TSW) which forms during the boron ore production is considered to be a promising building material with its use as an admixture with Portland cement and is considered to be an alternative radiation shielding material, also. Thus, having knowledge on the chemical composition and radiation interaction properties of TSW as compared to other building materials is of importance. In the present study, chemical compositions of the materials used have been determined using a wavelength dispersive X-ray fluorescence spectrometer (WDXRFS). Also, TSW, some commonly used building materials (Portland cement, lime and pointing) and their admixtures with TSW have been investigated in terms of total mass attenuation coefficients (μ/ρ), photon interaction cross sections (σ t ), effective atomic numbers (Z eff ) and effective electron densities (N e ) by using X-rays at 22.1, 25 keV and γ-rays at 88 keV photon energies. Possible conclusions were drawn with respect to the variations in photon energy and chemical composition.

Effect of the use nickeliferous laterite and pumice as additives in the performance and durability of the Portland cement

OpenAIRE

Rueda-Gualdrón, María Carolina; Vega-Nuñez, Karen Milena; Ríos-Reyes, Carlos Alberto

2016-01-01

This work evaluated the pozzolanic behavior of the niqueliferous laterite of Cerromatoso (Córdoba) and the pumice of Cemex (Boyacá), based on the NTC standards for fine aggregates. The mortars were prepared with additions of 2.5%, 5% and 10% as substitutes of type I Portland cement, which tested to extreme environments (high temperatures and chemical attacks with H2SO4 y MgSO4). Results demonstrates how these alternative materials increase or decrease their puzolanic degree, as well as the ef...

Clinical use of the Mayo-Portland Adaptability Inventory in rehabilitation after paediatric acquired brain injury.

Science.gov (United States)

Oddson, Bruce; Rumney, Peter; Johnson, Patricia; Thomas-Stonell, Nancy

2006-11-01

The Mayo-Portland Adaptability Inventory (MPAI; designed to be administered by clinicians) is a popular measure of disability following head injury in adults. Its acceptability, validity, and reliability were assessed for use with children. There were 335 children and adolescents (215 males, 120 females) aged between 1 and 19 years at injury (median age 9y 8mo [SD 5y]) in our sample. The test was acceptable to respondents, rapidly and easily administered, and required only small modifications. It demonstrated validity against client and parent reports of major symptoms. It demonstrated test-retest reliability within the limitations of our data and excellent interrater accord. Consequently, the MPAI is recommended for paediatric use for evaluating rehabilitation needs and therapy outcome.

Clinical and radiographic evaluation of Portland cement added to radiopacifying agents in primary molar pulpotomies.

Science.gov (United States)

Lourenço Neto, N; Marques, N C T; Fernandes, A P; Hungaro Duarte, M A; Abdo, R C C; Machado, M A A M; Oliveira, T M

2015-10-01

This was to evaluate the clinical and radiographic outcomes of Portland cement (PC) added to radiopacifying agents in primary molar pulpotomies. Thirty primary mandibular molars of children aged between 5 and 9 years were randomly assigned to the following groups: PC; PC with iodoform (PC + CHI(3)); PC with zirconium oxide (PC + ZrO(2)) and treated by pulpotomy technique. Clinical and radiographic follow-up assessments were performed at 6, 12 and 24 months. Statistical analysis was performed by Fisher's exact test (P < 0.05). The clinical and radiographic evaluations showed 100 % success rates, and the results showed no statistically significant difference between groups. According to this study, PC added to radiopacifying agents exhibited satisfactory clinical and radiographic results in primary molar pulpotomies.

Stakeholder value-linked sustainability assessment: Evaluating remedial alternatives for the Portland Harbor Superfund Site, Portland, Oregon, USA.

Science.gov (United States)

Apitz, Sabine E; Fitzpatrick, Anne G; McNally, Amanda; Harrison, David; Coughlin, Conor; Edwards, Deborah A

2018-01-01

Regulatory decisions on remediation should consider affected communities' needs and values, and how these might be impacted by remedial options; this process requires that diverse stakeholders are able to engage in a transparent consideration of value trade-offs and of the distribution of risks and benefits associated with remedial actions and outcomes. The Stakeholder Values Assessment (SVA) tool was developed to evaluate remedial impacts on environmental quality, economic viability, and social equity in the context of stakeholder values and priorities. Stakeholder values were linked to the pillars of sustainability and also to a range of metrics to evaluate how sediment remediation affects these values. Sediment remedial alternatives proposed by the US Environmental Protection Agency (USEPA) for the Portland Harbor Superfund Site were scored for each metric, based upon data provided in published feasibility study (FS) documents. Metric scores were aggregated to generate scores for each value; these were then aggregated to generate scores for each pillar of sustainability. In parallel, the inferred priorities (in terms of regional remediation, restoration, planning, and development) of diverse stakeholder groups (SGs) were used to evaluate the sensitivity and robustness of the values-based sustainability assessment to diverse SG priorities. This approach, which addresses social indicators of impact and then integrates them with indicators of environmental and economic impacts, goes well beyond the Comprehensive Environmental Response, Compensation and Liability Act's (CERCLA) 9 criteria for evaluating remedial alternatives because it evaluates how remedial alternatives might be ranked in terms of the diverse values and priorities of stakeholders. This approach identified trade-offs and points of potential contention, providing a systematic, semiquantitative, transparent valuation tool that can be used in community engagement. Integr Environ Assess Manag 2018

Proceedings of the International Symposium on Detonation (9th) Held in Portland, Oregon on 28 August - 1 September 1989. Volume 1

Science.gov (United States)

1989-09-01

compaction andeation pres wace , mixture (the loss of pressurization is due to the In the series of experiments investigat- venting into undisturbed...Detonation was held at the Red Lion Inn, Columbia River, Portland, Oregon, from August 28 through September 1, 1989. The Symposium was one of a series ...Francis Ree and Katsumi Tanaka The Detonation Parameters of New Powerful Explosive Compounds Predicted with a Revised VLW Equation of State W u Xiong

Freeze-Thaw Performance and Moisture-Induced Damage Resistance of Base Course Stabilized with Slow Setting Bitumen Emulsion-Portland Cement Additives

Directory of Open Access Journals (Sweden)

Mojtaba Shojaei Baghini

2015-01-01

Full Text Available Freeze-thaw (FT cycles and moisture susceptibility are important factors influencing the geotechnical characteristics of soil-aggregates. Given the lack of published information on the behavior of cement-bitumen emulsion-treated base (CBETB under environmental conditions, especially freezing and thawing, this study investigated the effects of these additives on the CBETB performance. The primary goal was to evaluate the resistance of CBETB to moisture damage by performing FT, Marshall conditioning, and AASHTO T-283 tests and to evaluate the long-term stripping susceptibility of CBETB while also predicting the liquid antistripping additives to assess the mixture’s durability and workability. Specimens were stabilized with Portland cement (0%–6%, bitumen emulsion (0%–5%, and Portland cement-bitumen emulsion mixtures and cured for 7 days, and their short- and long-term performances were studied. Evaluation results of both the Marshall stability ratio and the tensile strength ratio show that the additions of additives increase the resistance of the mixtures to moisture damage. Results of durability tests performed for determining the resistance of compacted specimens to repeated FT cycles indicate that the specimen with the 4% cement-3% bitumen emulsion mixture significantly improves water absorption, volume changes, and weight losses. This indicates the effectiveness of this additive as a road base stabilizer with excellent engineering properties for cold regions.

Secondary science teachers' attitudes toward and beliefs about science reading and science textbooks

Science.gov (United States)

Yore, Larry D.

Science textbooks are dominant influences behind most secondary science instruction but little is known about teachers' approach to science reading. The purpose of this naturalistic study was to develop and validate a Science and Reading Questionnaire to assess secondary science teachers' attitudes toward science reading and their beliefs or informed opinions about science reading. A survey of 428 British Columbia secondary science teachers was conducted and 215 science teachers responded. Results on a 12-item Likert attitude scale indicated that teachers place high value on reading as an important strategy to promote learning in science and that they generally accept responsibility for teaching content reading skills to science students. Results on a 13-item Likert belief scale indicated that science teachers generally reject the text-driven model of reading, but they usually do not have well-formulated alternative models to guide their teaching practices. Teachers have intuitive beliefs about science reading that partially agree with many research findings, but their beliefs are fragmented and particularly sketchy in regard to the cognitive and metacognitive skills required by readers to learn from science texts. The findings for attitude, belief, and total scales were substantiated by further questions in the Science and Reading Questionnaire regarding classroom practice and by individual interviews and classroom observations of a 15-teacher subsample of the questionnaire respondents.

Modelling of Pb release during Portland cement alteration

Energy Technology Data Exchange (ETDEWEB)

Benard, A. [INERIS Mediterrannee, F-13545 Aix En Provence 04 (France); Rose, J.; Borschneck, D.; Bottero, J.Y. [Univ Paul Cezanne, CNRS, UMR 6635, CEREGE, IFR PMSE 112, F-13545 Aix En Provence, (France); Hazemann, J.L. [CNRS, Cristallog Lab, F-38042 Grenoble 09 (France); Proux, O. [Univ Grenoble 1, CNRS, UMR, LGIT, F-38400 St Martin Dheres (France); Trotignon, L. [CEA Cadarache, DTN, SMTM, Lab Modelisat Transferts Environm, 13 - Saint Paul lez Durance (France); Nonat, A. [Univ Bourgogne, CNRS, UMR 5613, Fac Sci Mirande, Lab Rech Reactivite Solides, F-21078 Dijon (France); Chateau, L. [ADEME, F-49004 Angers (France)

2009-07-01

Complex cementitious matrices undergo weathering with environmental exchange and can release metallic pollutants during alteration. The molecular mechanisms responsible for metal release are difficult to identify, though this is necessary if such processes are to be controlled. The present study determines and models the molecular mechanisms of Pb release during Portland cement leaching. As Pb release is strongly related to its speciation (i.e. atomic environment and the nature of bearing phases), the first objective of the present study was to investigate the evolution of Pb retention sites together with the evolution of the cement mineralogy during leaching. Complementary and efficient investigation tools were used, namely X-ray diffraction, micro-X-ray fluorescence and X-ray absorption fine structures. The second objective was to reproduce our results with a reactive transport code (CHESS/HYTEC) in order to test the proposed speciation model of Pb. Combined results indicate that in both the unaltered core and the altered layer of the leached cement, Pb(II) would be retained through C-S-H 'nano-structure', probably linked to a Q(1) or Q(2P) silicate tetrahedra. Moreover in the altered layer, the presence of Fe atoms in the atomic environment of Pb is highly probable. Unfortunately little is known about Fe phases in cement, which makes the interpretation difficult. Can Fe-substituted hydrogranet (C(3)AH(6)) be responsible for Pb retention? Modelling results were consistent with Pb retention through C-S-H in layers and also in an additional, possibly Fe-containing, Pb-retention phase in the altered layer. (authors)

Influence of the waste glass in the axial compressive strength of Portland cement concrete; Influencia dos residuos vitreos na resistencia a compressao axial do concreto de cimento Portland

Energy Technology Data Exchange (ETDEWEB)

Miranda Junior, E.J.P.; Paiva, A.E.M., E-mail: edson.jansen@hotmail.com [Instituto Federal de Educacao, Ciencia e Tecnologia do Maranhao (PPGEM/IFMA), Sao Luis, MA (Brazil). Programa de Pos-Graduacao em Engenharia de Materiais

2012-07-01

In this work, was studied the influence of the incorporation of waste glass, coming from the stage of thinning and polishing of a company of thermal glass treatments, in the axial compressive strength of Portland cement concrete. The coarse and ground aggregates used was crushed stone and sand, respectively. For production of the concrete, percentages of glass residues of 5%, 10% and 20% had been used in substitution to the sand, and relations water/cement (a/c) 0,50, 0,55 and 0,58. The cure of the test bodies was carried through in 7, 14 and 28 days. The statistics analysis of the results was carried out through of the analysis of variance for each one of the cure times. From the results of the compressive strength of the concrete, it could be observed that the concrete has structural application for the relation a/c 0,5, independently of waste glass percentage used, and for the relation a/c 0,55 with 20% of waste glass. (author)

An STS Approach to Organizing a Secondary Science Methods Course: Preliminary Findings.

Science.gov (United States)

Dass, Pradeep M.

The current agenda in science education calls for science instruction that enhances student understanding of the nature of scientific enterprise, enables students to critically analyze scientific information as well as apply it in real-life situations, and sets them on a path of lifelong learning in science. In order to prepare teachers who can…

Potencial da cinza do bagaço da cana-de-açúcar como material de substituição parcial de cimento Portland Potential of sugarcane bagasse ash as a partial replacement material for Portland cement

Directory of Open Access Journals (Sweden)

Marcos O. de Paula

2009-06-01

Full Text Available Este trabalho, voltado para a avaliação do potencial da cinza do bagaço da cana-de-açúcar (CBC como material de substituição parcial do cimento Portland em argamassa, objetivou apresentar opção viável para a destinação deste resíduo, cuja quantidade gerada aumentará significativamente nos próximos anos, em decorrência da ampliação do setor de produção de álcool combustível; além disso, o emprego da CBC como adição mineral, substituindo parte do cimento em argamassas e concretos, contribui para a redução do impacto ambiental desses materiais, em boa parte decorrente da produção do cimento. O procedimento experimental abordou não só caracterização da CBC mas também a avaliação, através de ensaios físicos e mecânicos, em que os resultados mostraram que o bagaço apresenta rendimento de CBC de 10%, com a cinza sendo composta de 84% de SiO2 e 5% de Carbono. A sílica na CBC apresenta-se na fase amorfa e nas fases cristalinas de cristobalita e quartzo. Os índices de atividade pozolânica comprovam a reatividade da CBC. Do ponto de vista da resistência à compressão, argamassas com teores de CBC entre 0 e 30% indicaram a possibilidade de substituição de até 20% do cimento pela CBC.This study is focused on the evaluation of the effects of the partial replacement of Portland cement by sugarcane bagasse ash (CBC in mortars. The main objective was to find a suitable destination for an agricultural residue generated in an increasing amount in Brazil, as a result of the boom of the use of ethanol as an alternative fuel to gasoline. Also, the use of CBC as a mineral admixture in mortars and concretes contributes to a decrease in the environmental impact of these materials related to cement production. Experimental techniques were applied both for the CBC characterization and for the evaluation of its use as a mineral admixture in mortars, based on mechanical and physical tests. The yield of CBC from sugarcane

Microstructure engineering of Portland cement pastes and mortars through addition of ultrafine layer silicates

DEFF Research Database (Denmark)

Lindgreen, Holger; Geiker, Mette; Krøyer, Hanne

2008-01-01

Pozzolanic submicron-sized silica fume and the non-pozzolanic micron- and nano-sized layer silicates (clay minerals) kaolinite, smectite and palygorskite have been used as additives in Portland cement pastes and mortars. These layer silicates have different particle shape (needles and plates......), surface charge, and size (micron and nano). The structure of the resulting cement pastes and mortars has been investigated by atomic force microscopy (AFM), helium porosimetry, nitrogen adsorption (specific surface area and porosity), low-temperature calorimetry (LTC) and thermal analysis. The main result...... is that the cement paste structure and porosity can be engineered by addition of selected layer silicates having specific particle shapes and surface properties (e.g., charge and specific surface area). This seems to be due to the growth of calcium-silicate hydrates (C-S-H) on the clay particle surfaces...

Multicultural and multilingual approach: Mathematics, science, and engineering education for junior high school minority students and high school administrators. Final report

Energy Technology Data Exchange (ETDEWEB)

Crumbly, I.J.; Hodges, J.

1994-09-01

During the 1993 school year, LLNL and the US Department of Energy`s San Francisco Field Office provided funds through grant {number_sign}DE-FG03-93SF20045/A000 to assist Cooperative Developmental Energy Program (CDEP) with its network coalition of high school counselors from 19 states and with its outreach and early intervention program in mathematics, science and engineering for minority junior high school students. The program for high school counselors is called the National Educators Orientation Program (NEOP) and the outreach program for minority junior high school students is called the Mathematics, Science and Engineering Academy (MSEA). A total of 35 minority and female rising eighth grade students participated in the Second Annual Mathematics, Science, and Engineering Academy sponsored by the Cooperative Developmental Energy Program of Fort Valley State College (FVSC). There were 24 students from the middle Georgia area, 4 students from Oakland, California, and 7 students from Portland, Oregon. Each student was selected by counselor in his or her respective school. The selection criteria were based on the students` academic performance in science and mathematics courses.

Factor analysis of the Mayo-Portland Adaptability Inventory: structure and validity.

Science.gov (United States)

Bohac, D L; Malec, J F; Moessner, A M

1997-07-01

Principal-components (PC) factor analysis of the Mayo-Portland Adaptability Inventory (MPAI) was conducted using a sample of outpatients (n = 189) with acquired brain injury (ABI) to evaluate whether outcome after ABI is multifactorial or unifactorial in nature. An eight-factor model was derived which explained 64-4% of the total variance. The eight factors were interpreted as representing Activities of Daily Living, Social Initiation, Cognition, Impaired-Self-awareness/Distress, Social Skills/ Support, Independence, Visuoperceptual, and Psychiatric, respectively. Validation of the Cognition factor was supported when factor scores were correlated with various neuropsychological measures. In addition, 117 patient self-rating total scores were used to evaluate the Impaired Self-awareness/Distress factor. An inverse relationship was observed, supporting this factor's ability to capture the two-dimensional phenomena of diminished self-awareness or enhanced emotional distress. A new subscale structure is suggested, that may allow greater clinical utility in understanding how ABI manifests in patients, and may provide clinicians with a better structure for implementing treatment strategies to address specific areas of impairment and disability for specific patients. Additionally, more precise measurement of treatment outcomes may be afforded by this reorganization.

Stabilization/solidification of selenium-impacted soils using Portland cement and cement kiln dust

International Nuclear Information System (INIS)

Moon, Deok Hyun; Grubb, Dennis G.; Reilly, Trevor L.

2009-01-01

Stabilization/solidification (S/S) processes were utilized to immobilize selenium (Se) as selenite (SeO 3 2- ) and selenate (SeO 4 2- ). Artificially contaminated soils were prepared by individually spiking kaolinite, montmorillonite and dredged material (DM; an organic silt) with 1000 mg/kg of each selenium compound. After mellowing for 7 days, the Se-impacted soils were each stabilized with 5, 10 and 15% Type I/II Portland cement (P) and cement kiln dust (C) and then were cured for 7 and 28 days. The toxicity characteristic leaching procedure (TCLP) was used to evaluate the effectiveness of the S/S treatments. At 28 days curing, P doses of 10 and 15% produced five out of six TCLP-Se(IV) concentrations below 10 mg/L, whereas only the 15% C in DM had a TCLP-Se(IV) concentration 3 .H 2 O) and selenate substituted ettringite (Ca 6 Al 2 (SeO 4 ) 3 (OH) 12 .26H 2 O), respectively.

Radiopacity and cytotoxicity of Portland cement associated with niobium oxide micro and nanoparticles.

Science.gov (United States)

Mestieri, Leticia Boldrin; Tanomaru-Filho, Mário; Gomes-Cornélio, Ana Livia; Salles, Loise Pedrosa; Bernardi, Maria Inês Basso; Guerreiro-Tanomaru, Juliane Maria

2014-01-01

Mineral Trioxide Aggregate (MTA) is composed of Portland Cement (PC) and bismuth oxide (BO). Replacing BO for niobium oxide (NbO) microparticles (Nbµ) or nanoparticles (Nbη) may improve radiopacity and bioactivity. The aim of this study was to evaluate the radiopacity and cytotoxicity of the materials: (1) PC; (2) White MTA; (3) PC+30% Nbµ; (4) PC+30% Nbη. For the radiopacity test, specimens of the different materials were radiographed along an aluminum step-wedge. For cell culture assays, Saos-2 osteoblastic-cells (ATCC HTB-85) were used. Cell viability was evaluated through MTT assay, and bioactivity was assessed by alkaline phosphatase activity assay. The results demonstrated higher radiopacity for MTA, followed by Nbµ and Nbη, which had similar values. Cell culture analysis showed that PC and PC+NbO associations promoted greater cell viability than MTA. It was concluded that the combination of PC+NbO is a potential alternative for composition of MTA.

Hydrated Ordinary Portland Cement as a Carbonic Cement: The Mechanisms, Dynamics, and Implications of Self-Sealing and CO₂ Resistance in Wellbore Cements

Energy Technology Data Exchange (ETDEWEB)

Guthrie, George Drake Jr. [Los Alamos National Laboratory; Pawar, Rajesh J. [Los Alamos National Laboratory; Carey, James William [Los Alamos National Laboratory; Karra, Satish [Los Alamos National Laboratory; Harp, Dylan Robert [Los Alamos National Laboratory; Viswanathan, Hari S. [Los Alamos National Laboratory

2017-07-28

This report analyzes the dynamics and mechanisms of the interactions of carbonated brine with hydrated Portland cement. The analysis is based on a recent set of comprehensive reactive-transport simulations, and it relies heavily on the synthesis of the body of work on wellbore integrity that we have conducted for the Carbon Storage Program over the past decade.

Quantitative study of Portland cement hydration by X-ray diffraction/Rietveld analysis and independent methods

International Nuclear Information System (INIS)

Scrivener, K.L.; Fuellmann, T.; Gallucci, E.; Walenta, G.; Bermejo, E.

2004-01-01

X-ray diffraction (XRD) is a powerful technique for the study of crystalline materials. The technique of Rietveld refinement now enables the amounts of different phases in anhydrous cementitious materials to be determined to a good degree of precision. This paper describes the extension of this technique to a pilot study of the hydration of a typical Portland cement. To validate this XRD-Rietveld analysis technique, its results were compared with independent measures of the same materials by the analysis of backscattered electron images (BSE/IA) and thermogravimetric analysis (TGA). In addition, the internal consistency of the measurements was studied by comparing the XRD estimates of the amounts of hydrates formed with the amounts expected to form from the XRD estimates of the amounts of anhydrous materials reacted

Glycerol Salicylate-based Pulp-Capping Material Containing Portland Cement.

Science.gov (United States)

Portella, Fernando Freitas; Collares, Fabrício Mezzomo; Santos, Paula Dapper; Sartori, Cláudia; Wegner, Everton; Leitune, Vicente Castelo Branco; Samuel, Susana Maria Werner

2015-01-01

The purpose of this study was to evaluate the water sorption, solubility, pH and ability to diffuse into dentin of a glycerol salicylate-based, pulp-capping cement in comparison to a conventional calcium hydroxide-based pulp capping material (Hydcal). An experimental cement was developed containing 60% glycerol salicylate resin, 10% methyl salicylate, 25% calcium hydroxide and 5% Portland cement. Water sorption and solubility were determined based on mass changes in the samples before and after the immersion in distilled water for 7 days. Material discs were stored in distilled water for 24 h, 7 days and 28 days, and a digital pHmeter was used to measure the pH of water. The cement's ability to diffuse into bovine dentin was assessed by Raman spectroscopy. The glycerol salicylate-based cement presented higher water sorption and lower solubility than Hydcal. The pH of water used to store the samples increased for both cements, reaching 12.59 ± 0.06 and 12.54 ± 0.05 after 7 days, for Hydcal and glycerol salicylate-based cements, respectively. Both cements were able to turn alkaline the medium at 24 h and sustain its alkalinity after 28 days. Hydcal exhibited an intense diffusion into dentin up to 40 µm deep, and the glycerol salicylate-based cement penetrated 20 µm. The experimental glycerol salicylate-based cement presents good sorption, solubility, ability to alkalize the surrounding tissues and diffusion into dentin to be used as pulp capping material.

When Nature of Science Meets Marxism: Aspects of Nature of Science Taught by Chinese Science Teacher Educators to Prospective Science Teachers

Science.gov (United States)

Wan, Zhi Hong; Wong, Siu Ling; Zhan, Ying

2013-01-01

Nature of science (NOS) is beginning to find its place in the science education in China. In a study which investigated Chinese science teacher educators' conceptions of teaching NOS to prospective science teachers through semi-structured interviews, five key dimensions emerged from the data. This paper focuses on the dimension, "NOS content…

Estudo comparativo da análise de ciclo de vida de concretos geopoliméricos e de concretos à base de cimento Portland composto (CP II

Directory of Open Access Journals (Sweden)

Paulo Henrique Ribeiro Borges

Full Text Available A Análise de Ciclo de Vida (ACV é um método que inclui a compilação e avaliação das entradas, saídas e dos impactos de um produto ao longo do seu ciclo de vida. Os resultados desta análise são utilizados para escolher alternativas favoráveis para uma aplicação específica. Este artigo utilizou as ferramentas de ACV, apoiada pelo software Umberto, para comparar o processo de obtenção de concretos de cimento Portland com o de concretos geopoliméricos, obtidos da ativação alcalina de aluminossilicatos. O impacto ambiental foi avaliado considerando 1 m³ de cada concreto, sendo (i as emissões de CO2 (kg CO2/ m³ e (ii a demanda energética (MJ/m³ as variáveis para determinar o potencial sustentável de ambos materiais. O objetivo principal foi avaliar se os concretos geopoliméricos são mais sustentáveis do que os concretos tradicionais. Os resultados obtidos mostraram que o consumo energético é reduzido em 45,8% na produção do concreto geopolimérico, quando comparado à produção do concreto de cimento Portland de desempenho mecânico equivalente. Com relação às emissões de CO2, o concreto geopolimérico reduz as emissões em 72,4%, em comparação ao concreto tradicional de cimento Portland CPII. Assim, o primeiro se mostra uma alternativa a ser considerada, na produção de materiais de construção de menor impacto ambiental.

Water dynamics in hardened ordinary Portland cement paste or concrete: from quasielastic neutron scattering.

Science.gov (United States)

Bordallo, Heloisa N; Aldridge, Laurence P; Desmedt, Arnaud

2006-09-14

Portland cement reacts with water to form an amorphous paste through a chemical reaction called hydration. In concrete the formation of pastes causes the mix to harden and gain strength to form a rock-like mass. Within this process lies the key to a remarkable peculiarity of concrete: it is plastic and soft when newly mixed, strong and durable when hardened. These qualities explain why one material, concrete, can build skyscrapers, bridges, sidewalks and superhighways, houses, and dams. The character of the concrete is determined by the quality of the paste. Creep and shrinkage of concrete specimens occur during the loss and gain of water from cement paste. To better understand the role of water in mature concrete, a series of quasielastic neutron scattering (QENS) experiments were carried out on cement pastes with water/cement ratio varying between 0.32 and 0.6. The samples were cured for about 28 days in sealed containers so that the initial water content would not change. These experiments were carried out with an actual sample of Portland cement rather than with the components of cement studied by other workers. The QENS spectra differentiated between three different water interactions: water that was chemically bound into the cement paste, the physically bound or "glassy water" that interacted with the surface of the gel pores in the paste, and unbound water molecules that are confined within the larger capillary pores of cement paste. The dynamics of the "glassy" and "unboud" water in an extended time scale, from a hundred picoseconds to a few nanoseconds, could be clearly differentiated from the data. While the observed motions on the picosecond time scale are mainly stochastic reorientations of the water molecules, the dynamics observed on the nanosecond range can be attributed to long-range diffusion. Diffusive motion was characterized by diffusion constants in the range of (0.6-2) 10(-9) m(2)/s, with significant reduction compared to the rate of diffusion

A comparative evaluation of compressive strength of Portland cement with zinc oxide eugenol and Polymer-reinforced cement: An in vitro analysis

OpenAIRE

S Prakasam; Prakasam Bharadwaj; S C Loganathan; B Krishna Prasanth

2014-01-01

Objective: The purpose of this study is to evaluate the ultimate compressive strength of 50% and 25% Portland cement mixed with Polymer-reinforced zinc oxide eugenol and zinc oxide eugenol cement after 1 hour, 24 hours, and 7 days. Materials and Methods: One hundred and eighty samples were selected. The samples were made cylindrical of size 6 × 8 mm and were divided into six groups as follows with each group consisting of 10 samples. Group 1: Polymer-reinforced zinc oxide eugenol with...

Expanding the basic science debate: the role of physics knowledge in interpreting clinical findings.

Science.gov (United States)

Goldszmidt, Mark; Minda, John Paul; Devantier, Sarah L; Skye, Aimee L; Woods, Nicole N

2012-10-01

Current research suggests a role for biomedical knowledge in learning and retaining concepts related to medical diagnosis. However, learning may be influenced by other, non-biomedical knowledge. We explored this idea using an experimental design and examined the effects of causal knowledge on the learning, retention, and interpretation of medical information. Participants studied a handout about several respiratory disorders and how to interpret respiratory exam findings. The control group received the information in standard "textbook" format and the experimental group was presented with the same information as well as a causal explanation about how sound travels through lungs in both the normal and disease states. Comprehension and memory of the information was evaluated with a multiple-choice exam. Several questions that were not related to the causal knowledge served as control items. Questions related to the interpretation of physical exam findings served as the critical test items. The experimental group outperformed the control group on the critical test items, and our study shows that a causal explanation can improve a student's memory for interpreting clinical details. We suggest an expansion of which basic sciences are considered fundamental to medical education.

Using Video to Communicate Scientific Findings -- Habitat Connections in Urban Streams

Science.gov (United States)

Harned, D. A.; Moorman, M.; Fitzpatrick, F. A.; McMahon, G.

2011-12-01

The U.S Geological Survey (USGS) National Water-Quality Assessment Program (NAWQA) provides information about (1) water-quality conditions and how those conditions vary locally, regionally, and nationally, (2) water-quality trends, and (3) factors that affect those conditions. As part of the NAWQA Program, the Effects of Urbanization on Stream Ecosystems (EUSE) study examined the vulnerability and resilience of streams to urbanization. Completion of the EUSE study has resulted in over 20 scientific publications. Video podcasts are being used in addition to these publications to communicate the relevance of these scientific findings to more general audiences such as resource managers, educational groups, public officials, and the general public. An example of one of the podcasts is a film examining effects of urbanization on stream habitat. "Habitat Connections in Urban Streams" explores how urbanization changes some of the physical features that provide in-stream habitat and examines examples of stream restoration projects designed to improve stream form and function. The "connections" theme is emphasized, including the connection of in-stream habitats from the headwaters to the stream mouth; connections between stream habitat and the surrounding floodplains, wetlands and basin; and connections between streams and people-- resource managers, public officials, scientists, and the general public. Examples of innovative stream restoration projects in Baltimore Maryland; Milwaukee, Wisconsin; and Portland Oregon are shown with interviews of managers, engineers, scientists, and others describing the projects. The film is combined with a website with links to extended film versions of the stream-restoration project interviews. The website and films are an example of USGS efforts aimed at improving science communication to a general audience. The film is available for access from the EUSE website: http://water.usgs.gov/nawqa/urban/html/podcasts.html. Additional films are

Our findings, my method: Framing science in televised interviews.

Science.gov (United States)

Armon, Rony; Baram-Tsabari, Ayelet

2017-11-01

The public communication of science and technology largely depends on their framing in the news media, but scientists' role in this process has only been explored indirectly. This study focuses on storied accounts told by scientists when asked to present their research or provide expert advice in the course of a news interview. A total of 150 items from a current affairs talk show broadcast in the Israeli media were explored through a methodology combining narrative and conversation analysis. Using the concept of framing as originally proposed by Erving Goffman, we show that researchers use personal accounts as a way of reframing news stories introduced by the program hosts. Elements of method and rationale, which are usually considered technical and are shunned in journalistic reports, emerged as a crucial element in the accounts that experts themselves provided. The implications for framing research and science communication training are discussed.

On the corrosion behaviour of stainless steel, nickel-chromium and zirconium-alloys in pore water of Portland cement

International Nuclear Information System (INIS)

Heitz, E.; Graefen, H.

1991-12-01

On the basis of an extensive review of literature and available experience, an evaluation was made of the corrosion of a metallic matrix for radioactive nuclides embedded in porous, water containing Portland cement. As a metallic matrix, austenitic high-alloy steel, nickel-base alloys and zirconium alloys are discussed. Pore waters in Portland cement have low aggressivity. However, through contact with formation water, chloride and sulphate enrichment can occur. Although corrosion is principally possible on the basis of purely thermodynamic considerations, it can be assumed that local corrosion (pitting, stress corrosion cracking, intergranular corrosion) is highly improbable under the given boundary conditions. This is valid for all three groups of alloys and means that only low release rates of corrosion products are to be expected. As a result of the discussion on radiolysis-induced corrosion, additional corrosion activity can be excluded. Final conclusions concerning the stimulation of corrosion processes by microbial action cannot be drawn and, therefore, additional experiments are proposed. The release rates of radioactive products are controlled by a very low dissolution rate of the materials in the passive state. All three groups of alloys show this type of general dissolution. From a survey of literature data it can be concluded that release rates greater than 250 mg/m 2 per day are not exceeded. Since these data were mainly obtained by electrochemical methods, it is proposed that quantitative analytical investigations of the corrosion products in pore water be made. On the whole the release rates determined are far below corrosion rates which are generally technically relevant. (author) 13 figs., 9 tabs., 61 refs

Preparation of iron-modified portland cement adsorbent and the investigation of its decolorization performance

Science.gov (United States)

Jiang, Bo; Wang, Huifeng; Li, Yang; Li, Zhen

2018-02-01

The ordinary portland cement was modified by ferric salt impregnation method. Through the technologies of x-ray diffraction, scanning electron microscope and energy dispersive spectroscopy, the physicochemical properties of modified cement were detected and analyzed. It was found that after the modification, the main constituents of raw cement, tricalcium silicate and dicalcium silicate had been depleted, and the new crystal mineral of antarcticite replaced them. The iron precipitates and cement hydration products calcium silicate hydrate gel mainly existed in the form of amorphous on modified cement. The results of BET specific surface determination showed that the modified cement particles had mesoporous distribution. The results of adsorption experiment revealed modified cement exhibited excellent adsorption performance on reactive brilliant blue KNR. The combination mechanism between modified cement and adsorbate was mainly electrostatic interaction. The adsorption process satisfied with the pseudo-second order kinetics model, and the adsorption reaction was a spontaneous endothermic process.

Pore size distribution, strength, and microstructure of portland cement paste containing metal hydroxide waste

Energy Technology Data Exchange (ETDEWEB)

Majid, Z.A.; Mahmud, H.; Shaaban, M.G.

1996-12-31

Stabilization/solidification of hazardous wastes is used to convert hazardous metal hydroxide waste sludge into a solid mass with better handling properties. This study investigated the pore size development of ordinary portland cement pastes containing metal hydroxide waste sludge and rice husk ash using mercury intrusion porosimetry. The effects of acre and the addition of rice husk ash on pore size development and strength were studied. It was found that the pore structures of mixes changed significantly with curing acre. The pore size shifted from 1,204 to 324 {angstrom} for 3-day old cement paste, and from 956 to 263 {angstrom} for a 7-day old sample. A reduction in pore size distribution for different curing ages was also observed in the other mixtures. From this limited study, no conclusion could be made as to any correlation between strength development and porosity. 10 refs., 6 figs., 3 tabs.

Effect of the use nickeliferous laterite and pumice as additives in the performance and durability of the Portland cement

OpenAIRE

María Carolina Rueda-Gualdrón; Karen Milena Vega-Nuñez; Carlos Alberto Ríos-Reyes

2016-01-01

En este trabajo se evalúa el comportamiento puzolánico de la laterita niquelífera de Cerromatoso (Córdoba) y la pumita de Cemex (Boyacá) en la preparación de morteros según normas NTC para agregados finos. Los morteros se prepararon con adiciones de 2,5%, 5% y 10% como sustitutos del cemento Portland tipo I, los cuales fueron sometidos a ensayos de resistencia mecánica antes y después de ser sometidos a ambientes extremos (altas temperaturas y ataques químicos como H2 SO4 y MgSO4 ). Los resu...

Effects of simvastain and enamel matrix derivative on Portland cement with bismuth oxide-induced growth and odontoblastic differentiation in human dental pulp cells.

Science.gov (United States)

Lee, So-Youn; Min, Kyung-San; Choi, Gi-Woon; Park, Jae-Hong; Park, Sang-Hyuk; Lee, Sang-Im; Kim, Eun-Cheol

2012-03-01

We previously reported that bismuth oxide containing Portland cement (BPC) showed similar biocompatibility to Portland cement (PC) in periodontal ligament cells. However, the bioactivity of simvastatin and Emdogain (Biora AB, Malmö, Sweden) on BPC was not reported. The aim of this study was to evaluate the effects of simvastatin and Emdogain on BPC compared with mineral trioxide aggregate (MTA) in human dental pulp cells (HDPCs). Cell growth was determined by 3-(4,5-Dimethylthiazol-2-yl)-2,5-diphenyltetrazolium-bromide (MTT) assay. Differentiation was evaluated by alkaline phosphatase (ALP) activity, alizarin red staining, and reverse-transcriptase polymerase chain reaction. The cell growth of HDPCs exposed to Emdogain and simvastatin plus BPC was superior to those administered BPC alone and similar to those that received MTA for 14 days. The simvastatin and Emdogain groups increased the odontogenic potential of the BPC group with respect to ALP activity, mineralization nodules, messenger RNA expression of ALP, osteopontin, osteocalcin, Runx2, and osterix. These results suggest that simvastatin and Emdogain improved cell growth and the differentiation of the BPC group in HDPCs and may be useful ingredients in BPC as pulp-capping material. Copyright © 2012 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Application of probabilistic risk assessment: Evaluating remedial alternatives at the Portland Harbor Superfund Site, Portland, Oregon, USA.

Science.gov (United States)

Ruffle, Betsy; Henderson, James; Murphy-Hagan, Clare; Kirkwood, Gemma; Wolf, Frederick; Edwards, Deborah A

2018-01-01

A probabilistic risk assessment (PRA) was performed to evaluate the range of potential baseline and postremedy health risks to fish consumers at the Portland Harbor Superfund Site (the "Site"). The analysis focused on risks of consuming fish resident to the Site containing polychlorinated biphenyls (PCBs), given that this exposure scenario and contaminant are the primary basis for US Environmental Protection Agency's (USEPA's) selected remedy per the January 2017 Record of Decision (ROD). The PRA used probability distributions fit to the same data sets used in the deterministic baseline human health risk assessment (BHHRA) as well as recent sediment and fish tissue data to evaluate the range and likelihood of current baseline cancer risks and noncancer hazards for anglers. Areas of elevated PCBs in sediment were identified on the basis of a geospatial evaluation of the surface sediment data, and the ranges of risks and hazards associated with pre- and postremedy conditions were calculated. The analysis showed that less active remediation (targeted to areas with the highest concentrations) compared to the remedial alternative selected by USEPA in the ROD can achieve USEPA's interim risk management benchmarks (cancer risk of 10 -4 and noncancer hazard index [HI] of 10) immediately postremediation for the vast majority of subsistence anglers that consume smallmouth bass (SMB) fillet tissue. In addition, the same targeted remedy achieves USEPA's long-term benchmarks (10 -5 and HI of 1) for the majority of recreational anglers. Additional sediment remediation would result in negligible additional risk reduction due to the influence of background. The PRA approach applied here provides a simple but adaptive framework for analysis of risks and remedial options focused on variability in exposures. It can be updated and refined with new data to evaluate and reduce uncertainty, improve understanding of the Site and target populations, and foster informed remedial decision

Resistencia química del hormigón III.-Acción del agua de mar. Influencia de la adición de escoria al cemento portland (I. parte

Directory of Open Access Journals (Sweden)

Gaspar-Tebar, Demetrio

1979-06-01

Full Text Available En publicaciones anteriores (1 (2 se dio cuenta de los trabajos efectuados para estudiar el comportamiento de dos cementos portland industriales, en la primera, y la influencia que ejerce la adición de diversas cantidades de una escoria vítrea a un cemento portland ambos de fabricación española, en la segunda, cuando los morteros (1:3 fabricados con dichos cementos o con las mezclas cemento/escoria se someten a la acción del agua de mar, determinando la evolución de las resistencias mecánicas a flexotracción, la variación de los coeficientes de corrosión (Kodi-Steinegger, la modificación de la concentración iónica de los medios en donde han estado sumergidas las probetas, así como la composición estructural de la fase sólida formada y de la fracción enriquecida del conglomerante hidratado.

Setting temperature evolution of nitrate radwaste immobilized in ordinary portland cement

International Nuclear Information System (INIS)

Rzyski, B.M.; Suarez, A.A.

1988-01-01

Materials based on hydraulic cements such as ordinary Portland cement (OPC) have many applications in the radioactive waste disposal field. Cement hydration process is an exothermic reaction and can cause a considerable temperature rise in the cemented waste form. Specially when large blocks of waste forms are produced it is necessary to have some information about the temperature build up which occurs inside the mass, because this effect may have some influences on the ultimate properties of the hardened cement paste. This temperature rise cause expansion while the cement paste is hardening. When the cooling process takes place, to the surrounding temperature, crackings and contractions may then occur. Whether cracking arise it depends both on the magnitude of the temperature induced stress and on the capacity of the mixture to accommodate the strain. This paper compares the temperature growth in pastes into two different geometries: one uses a waste container with 3.8 dm 3 (one US gallon) capacity placed inside a 0.21 m 3 (55 gallons) concrete lined drum, which acts as a radiation shielding, and the other the same container placed in ambient at room temperature. Correlations between the time of temperature occurrence, maximum temperature, the water to cement ratio and salt content were observed

Effect of MTA and Portland Cement on Fracture Resistance of Dentin

Directory of Open Access Journals (Sweden)

Maryam Forghani

2013-06-01

Full Text Available Background and aims. It is important to evaluate the effects of endodontic materials on tooth structures to avoid endodontic treatment failure. The aim of the present study was to investigate the effect of mineral trioxide aggregates (MTA and Portland cement (PC on fracture resistance of dentin. Materials and methods. Thirty-six freshly extracted human single-rooted premolar teeth were selected. The crowns were removed and the roots were randomly divided into two experimental groups and one control group. The root samples were longitudinally divided into two halves and a dentin bar (2×2×10 mm was cut from each root section for short-term (2 weeks and long-term (12 weeks evaluations. The root sections in the experimental groups were exposed to MTA or PC, while keeping the control group specimens in physiologic saline. The fracture resistance of each specimen was measured using an Instron testing machine. The results were statistically analyzed using ANOVA, a post hoc Tukey test and paired ttest at 5% significance level. Results. The fracture resistance of MTA-treated specimens significantly increased between 2 and 12 weeks (P0.05. Conclusion. The results showed that MTA increased the fracture resistance of root dentin, while PC had no significant effect on dentin fracture resistance.

The Minimal Clinically Important Difference for the Mayo-Portland Adaptability Inventory.

Science.gov (United States)

Malec, James F; Kean, Jacob; Monahan, Patrick O

To determine the Minimal Clinically Important Difference (MCID) and Robust Clinically Important Difference (RCID) of the Mayo-Portland Adaptability Inventory-4 (MPAI-4) as measures of response to intervention. Retrospective analysis of existing data. Both distribution- and anchor-based methods were used to triangulate on the MCID and to identify a moderate, that is, more robust, level of change (RCID) for the MPAI-4. These were further evaluated with respect to clinical provider ratings. Data for individuals with acquired brain injury in rehabilitation programs throughout the United States in the OutcomeInfo Database (n = 3087) with 2 MPAI-4 ratings. MPAI-4, Supervision Rating Scale, Clinician Rating of Global Clinical Improvement. Initial analyses suggested 5 T-score points (5T) as the MCID and 9T as the RCID. Eighty-one percent to 87% of clinical raters considered a 5T change and 99% considered a 9T change to indicate meaningful improvement. 5T represents the MCID for the MPAI-4 and 9T, the RCID. Both values are notably less than the Reliable Change Index (RCI). While the RCI indicates change with a high level of statistical confidence, it may be insensitive to change that is considered meaningful by providers and participants as indicated by the MCID.

Finding the Hook: Computer Science Education in Elementary Contexts

Science.gov (United States)

Ozturk, Zehra; Dooley, Caitlin McMunn; Welch, Meghan

2018-01-01

The purpose of this study was to investigate how elementary teachers with little knowledge of computer science (CS) and project-based learning (PBL) experienced integrating CS through PBL as a part of a standards-based elementary curriculum in Grades 3-5. The researchers used qualitative constant comparison methods on field notes and reflections…

What's science? Where's science? Science journalism in German print media.

Science.gov (United States)

Summ, Annika; Volpers, Anna-Maria

2016-10-01

This article examines the current state of science coverage in German print media. It deals with the following questions: (1) how the main characteristics of science journalism can be described, (2) whether there is a difference between various scientific fields, and (3) how different definitions of science journalism lead to differing findings. Two forms of science coverage were analyzed in a standardized, two-part content analysis of German newspapers (N = 1730 and N = 1640). The results show a significant difference between a narrow and a broad definition of science journalism. In the classic understanding, science journalism is prompted by scientific events and is rather noncritical. Science coverage in a broad sense is defined by a wider range of journalistic styles, driven by non-scientific events, and with a focus on the statements of scientific experts. Furthermore, the study describes the specific role of the humanities and social sciences in German science coverage. © The Author(s) 2015.

Science Standards, Science Achievement, and Attitudes about Evolution

Science.gov (United States)

Belin, Charlie M.; Kisida, Brian

2015-01-01

This article explores the relationships between (a) the quality of state science standards and student science achievement, (b) the public's belief in teaching evolution and the quality of state standards, and (c) the public's belief in teaching evolution and student science achievement. Using multiple measures, we find no evidence of a…

Thermodynamic description of the solubility of C-S-H gels in hydrated Portland cement. Literature review

International Nuclear Information System (INIS)

Soler, J.M.

2007-11-01

The objective of this study is to compile the available information published in the scientific literature regarding the solubility of C-S-H (calcium silica hydrate) gels, which are the main components of hydrated Portland cement. Modeling the thermodynamic properties of C-S-H, including its incongruent dissolution behavior, is an important requirement to understand the evolution and degradation of hydrated cement and concrete. The thermodynamic modeling of C-S-H started with the use of empirical or semi-empirical models and evolved to the application of solid solution models. Most of the experimental work has been performed at or near 25 deg C and the models are in principle applicable to temperatures near 25 deg C. One of the models provides an explicit dependence on temperature. (orig.)

Microstructural characterization of phases and interfaces of Portland cement mortar using high resolution microscopy

International Nuclear Information System (INIS)

Barreto, M.F.O.; Brandao, P.R.G.

2014-01-01

In Portland cement mortars it is of paramount importance to investigate the bond strength between mortar and masonry by means of the study of interfaces and surfaces that make up the system mortar/ceramic block. In this work the aim was to characterize the chemical compositions, microstructures, surfaces and interfaces of mortars applied on ceramic blocks. Therefore, two important characterization tools were used: field-effect gun (FEG) scanning electron microscope (SEM) - FEI Quanta 200 with energy-dispersive (X-ray) spectrometer (EDS) and SEM system with EGF Nanofabrication FIB - FEI Quanta 3D FEG also with an EDS coupled. To date the results obtained from the research show that the characterization of cementitious materials with high resolution SEM is an important tool in the detection and differentiation of hydrated calcium silicates (CSH), calcium hydroxide (Ca(OH)2), ettringite and calcium carbonate by means of morphological, topographical and chemical data, thus providing extremely reliable as well as qualitative data from the structure of cementitious materials. (author)

Microstructural characterization of phases and interfaces of Portland cement mortar using high resolution microscopy

Energy Technology Data Exchange (ETDEWEB)

Barreto, M.F.O.; Brandao, P.R.G., E-mail: matheusfob@yahoo.com.br, E-mail: pbrandao@demin.ufmg.br [Universidade Federal de Minas Gerais (UFMG), MG (Brazil)

2014-07-01

In Portland cement mortars it is of paramount importance to investigate the bond strength between mortar and masonry by means of the study of interfaces and surfaces that make up the system mortar/ceramic block. In this work the aim was to characterize the chemical compositions, microstructures, surfaces and interfaces of mortars applied on ceramic blocks. Therefore, two important characterization tools were used: field-effect gun (FEG) scanning electron microscope (SEM) - FEI Quanta 200 with energy-dispersive (X-ray) spectrometer (EDS) and SEM system with EGF Nanofabrication FIB - FEI Quanta 3D FEG also with an EDS coupled. To date the results obtained from the research show that the characterization of cementitious materials with high resolution SEM is an important tool in the detection and differentiation of hydrated calcium silicates (CSH), calcium hydroxide (Ca(OH)2), ettringite and calcium carbonate by means of morphological, topographical and chemical data, thus providing extremely reliable as well as qualitative data from the structure of cementitious materials. (author)

Effects of cement particle size distribution on performance properties of Portland cement-based materials

Energy Technology Data Exchange (ETDEWEB)

Bentz, D.P.; Garboczi, E.J.; Haecker, C.J.; Jensen, O.M.

1999-10-01

The original size, spatial distribution, and composition of Portland cement particles have a large influence on hydration kinetics, microstructure development, and ultimate properties of cement-based materials. In this paper, the effects of cement particle size distribution on a variety of performance properties are explored via computer simulation and a few experimental studies. Properties examined include setting time, heat release, capillary porosity percolation, diffusivity, chemical shrinkage, autogenous shrinkage, internal relative humidity evolution, and interfacial transition zone microstructure. The effects of flocculation and dispersion of the cement particles in the starting microstructures on resultant properties are also briefly evaluated. The computer simulations are conducted using two cement particle size distributions that bound those commonly in use today and three different water-to-cement ratios: 0.5, 0.3, and 0.246. For lower water-to-cement ratio systems, the use of coarser cements may offer equivalent or superior performance, as well as reducing production costs for the manufacturer.

CERCLA-linked environmental impact and benefit analysis: Evaluating remedial alternatives for the Portland Harbor Superfund Site, Portland, Oregon, USA.

Science.gov (United States)

McNally, Amanda D; Fitzpatrick, Anne G; Mirchandani, Sera; Salmon, Matthew; Edwards, Deborah A

2018-01-01

This analysis focused on evaluating the environmental consequences of remediation, providing indicators for the environmental quality pillar of 3 "pillars" of the Portland Harbor Sustainability Project (PHSP) framework (the other 2 pillars are economic viability and social equity). The project an environmental impact and benefit analysis (EIBA) and an EIBA-based cost-benefit analysis. Metrics developed in the EIBA were used to quantify and compare remedial alternatives' environmental benefits and impacts in the human and ecological domains, as a result of remedial actions (relative to no action). The cost-benefit results were used to evaluate whether remediation costs were proportionate or disproportionate to the environmental benefits. Alternatives B and D had the highest overall benefit scores, and Alternative F was disproportionately costly relative to its achieved benefits when compared to the other remedial alternatives. Indeed, the costlier alternatives with larger remedial footprints had lower overall EIBA benefit scores-because of substantially more air emissions, noise, and light impacts, and more disturbance to business, recreational access, and habitat during construction-compared to the less costly and smaller alternatives. Put another way, the adverse effects during construction tended to outweigh the long-term benefits, and the net environmental impacts of the larger remedial alternatives far outweighed their small incremental improvements in risk reduction. Results of this Comprehensive Environmental Response Compensation and Liability Act (CERCLA)-linked environmental analysis were integrated with indicators of economic and social impacts of remediation in a stakeholder values-based sustainability framework. These tools (EIBA, EIBA-based cost-benefit analysis, economic impact assessment, and the stakeholder values-based integration) provide transparent and quantitative evaluations of the benefits and impacts associated with remedial alternatives

Microencapsulated phase change materials for enhancing the thermal performance of Portland cement concrete and geopolymer concrete for passive building applications

International Nuclear Information System (INIS)

Cao, Vinh Duy; Pilehvar, Shima; Salas-Bringas, Carlos; Szczotok, Anna M.; Rodriguez, Juan F.; Carmona, Manuel; Al-Manasir, Nodar; Kjøniksen, Anna-Lena

2017-01-01

Highlights: • Microencapsulated phase change materials give high energy storage capacity concrete. • Microcapsule addition increases the porosity of concrete. • Thermal and mechanical properties are linked to the enhanced concrete porosity. • Agglomerated microcapsules have strong impact on the concrete properties. • Microcapsules caused geopolymer to become more energy efficient than Portland cement. - Abstract: Concretes with a high thermal energy storage capacity were fabricated by mixing microencapsulated phase change materials (MPCM) into Portland cement concrete (PCC) and geopolymer concrete (GPC). The effect of MPCM on thermal performance and compressive strength of PCC and GPC were investigated. It was found that the replacement of sand by MPCM resulted in lower thermal conductivity and higher thermal energy storage, while the specific heat capacity of concrete remained practically stable when the phase change material (PCM) was in the liquid or solid phase. Furthermore, the thermal conductivity of GPC as function of MPCM concentration was reduced at a higher rate than that of PCC. The power consumption needed to stabilize a simulated indoor temperature of 23 °C was reduced after the addition of MPCM. GPC exhibited better energy saving properties than PCC at the same conditions. A significant loss in compressive strength was observed due to the addition of MPCM to concrete. However, the compressive strength still satisfies the mechanical European regulation (EN 206-1, compressive strength class C20/25) for concrete applications. Finally, MPCM-concrete provided a good thermal stability after subjecting the samples to 100 thermal cycles at high heating/cooling rates.

Absorption Characteristics of Cement Combination Concrete Containing Portland Cement, fly ash, and Metakaolin

Directory of Open Access Journals (Sweden)

Folagbade S.O.

2016-03-01

Full Text Available The resistance to water penetration of cement combination concretes containing Portland cement (PC, fly ash (FA, and metakaolin (MK have been investigated at different water/cement (w/c ratios, 28-day strengths, and depths of water penetration using their material costs and embodied carbon-dioxide (eCO2 contents. Results revealed that, at equal w/c ratio, eCO2 content reduced with increasing content of FA and MK. MK contributed to the 28-day strengths more than FA. Compared with PC, FA reduced cost and increased the depth of water penetration, MK increased cost and reduced the depth of water penetration, and their ternary combinations become beneficial. At equal strengths and levels of resistance to water penetration, most of the cement combination concretes are more environmentally compatible and costlier than PC concrete. Only MK binary cement concretes with 10%MK content or more and ternary cement concretes at a total replacement level of 55% with 10%MK content or more have higher resistance to water penetration than PC concrete.

Characterization of Moroccan coal waste: valorization in the elaboration of the Portland clinker

Directory of Open Access Journals (Sweden)

Belkheiri D.

2014-04-01

Full Text Available Coal exploited in the mine of Jerada (northeast of Morocco was accompanied by large quantities of waste. The purpose of this work is to characterize this waste with the aim of its use as a material for civil engineering. Mineral and chemical investigations on this waste in the raw state, and at different temperature of heat treatments, were carried out by various methods: X-ray fluorescence, X-ray diffraction, infrared spectroscopy. These analyzes showed that the studied waste, contain essentially a mineral part formed by silica and various clays, as well as coal’s residues. The thermal investigation of waste, by differential scanning calorimetry (DSC, revealed an exothermic phenomenon attributed to the combustion of coal residues. Other phenomena were noted on the thermograms due to the mineral part transformations. In this analysis a comparison was also made with pure coal. These characteristics of coal waste encourage studying its development in reducing energy consumption in the Portland cement manufacture. Mixtures of waste with limestone or with raw cement materials were studied, and the resulting products were analyzed by different methods.

The impact of sulphate and magnesium on chloride binding in Portland cement paste

Energy Technology Data Exchange (ETDEWEB)

De Weerdt, K., E-mail: klaartje.d.weerdt@ntnu.no [Department of Structural Engineering, Norwegian University of science and Technology, Trondheim (Norway); SINTEF Building and Infrastructure, Trondheim (Norway); Orsáková, D. [Department of Civil Engineering, Technical University of Brno, Brno (Czech Republic); Geiker, M.R. [Department of Structural Engineering, Norwegian University of science and Technology, Trondheim (Norway)

2014-11-15

The effect of magnesium and sulphate present in sea water on chloride binding in Portland cement paste was investigated. Ground well hydrated cement paste was exposed to MgCl{sub 2}, NaCl, NaCl + MgCl{sub 2}, MgSO{sub 4} + MgCl{sub 2} and artificial sea water solutions with a range of concentrations at 20 °C. Chloride binding isotherms are determined and pH of the solutions were measured. A selection of samples was examined by SEM-EDS to identify phase changes upon exposure. The experimental data were compared with calculations of a thermodynamic model. Chloride binding from sea water was similar to chloride binding for NaCl solutions. The magnesium content in the sea water lead to a slight decrease in pH, but this did not result in a notable increase in chloride binding. The sulphate present in sea water reduces both chloride binding in C–S–H and AFm phases, as the C–S–H incorporates more sulphates instead of chlorides, and part of the AFm phases converts to ettringite.

Effects of fibers on expansive shotcrete mixtures consisting of calcium sulfoaluminate cement, ordinary Portland cement, and calcium sulfate

Directory of Open Access Journals (Sweden)

H. Yu

2018-04-01

Full Text Available The mining industry often uses shotcrete for ground stabilization. However, cracking within shotcrete is commonly observed, which delays production schedules and increases maintenance costs. A possible crack reduction method is using expansive shotcrete mixture consisting of calcium sulfoaluminate cement (CSA, ordinary Portland cement (OPC, and calcium sulfate (CS to reduce shrinkage. Furthermore, fibers can be added to the mixture to restrain expansion and impede cracking. The objective of this paper is to study the effects of nylon fiber, glass fiber, and steel fiber on an expansive shotcrete mixture that can better resist cracking. In this study, parameters such as density, water absorption, volume of permeable voids, unconfined compressive strength (UCS, splitting tensile strength (STS, and volume change of fiber-added expansive mixtures were determined at different time periods (i.e. the strengths on the 28th day, and the volume changes on the 1st, 7th, 14th, 21st, and 28th days. The results show that addition of fibers can improve mixture durability, in the form of decreased water absorption and reduced permeable pore space content. Moreover, the expansion of the CSA-OPC-CS mixture was restrained up to 50% by glass fiber, up to 43% by nylon fiber, and up to 28% by steel fiber. The results show that the STS was improved by 57% with glass fiber addition, 43% with steel fiber addition, and 38% with nylon fiber addition. The UCS was also increased by 31% after steel fiber addition, 26% after nylon fiber addition, and 16% after glass fiber addition. These results suggest that fiber additions to the expansive shotcrete mixtures can improve durability and strengths while controlling expansion. Keywords: Shotcrete, Restrained expansion, Fibers, Calcium sulfoaluminate cement (CSA, Ordinary Portland cement (OPC, Calcium sulfate (CS

Electroretinographic findings in transplant chorioretinopathy

Directory of Open Access Journals (Sweden)

Brian T Chan-Kai

2010-07-01

Full Text Available Brian T Chan-Kai1, Steven Yeh2, Richard G Weleber2, Peter J Francis2, Grazyna Adamus2, S Robert Witherspoon3, Andreas K Lauer11Cullen Eye Institute, Baylor College of Medicine, Houston, Texas; 2Casey Eye Institute, Oregon Health and Science University, Portland, Oregon; 3Retina Institute of Texas, Dallas, Texas, USAAim: Transplant chorioretinopathy is a rare complication following solid organ or bone ­marrow transplantation and can result in severe vision loss. This series presents electroretinogram (ERG results in patients with this condition.Methods: Patients who presented with bilateral vision loss following bone marrow or solid organ transplantation were identified. A complete ophthalmologic examination, fundus ­photography, and fluorescein angiography (FA were performed. Full-field ERG was obtained in all patients and a multifocal ERG (mfERG was obtained in two patients.Results: Four patients were identified. All patients had bilateral vision loss and displayed a characteristic pattern of mottled hyperfluorescence on FA. Three patients developed ­progressive vision loss ranging from 20/60 to hand motions whereas one retained 20/40 vision. All patients exhibited moderate to severe cone dysfunction, while the degree of rod abnormalities was varied. Two patients with severe cone dysfunction showed mild clinical changes initially, but later developed progressive vision loss and chorioretinal atrophy.Conclusion: Transplant chorioretinopathy patients undergoing ERG testing show cone ­dysfunction with a variable degree of rod dysfunction. ERG abnormalities preceded the visual acuity and clinical changes in two patients, suggesting that ERG may be a helpful predictor of the clinical course in this rare disease.Keywords: transplant, chorioretinopathy, electroretinogram, ERG, mfERG

Avaliação da atividade pozolânica da cinza pesada moída em pastas de cimento Portland

OpenAIRE

Pilar, Ronaldo

2012-01-01

Dissertação (mestrado) - Universidade Federal de Santa Catarina, Centro Tecnológico. Programa de Pós-Graduação em Engenharia Civil O uso de adições minerais finamente moídas em substituição parcial do clínquer é prática comum na produção de cimento Portland. Normalmente estas substituições estão amparadas por razões técnicas, econômicas e ambientais. Embora já se tenha conhecimento de uma vasta gama de materiais que possuem propriedades pozolânicas, ainda existem alguns com grande disponib...

Diferencias y similitudes entre morteros de cal hidráulica y morteros mixtos de cal área y cemento portland

OpenAIRE

Peñaranda García, Pilar

2012-01-01

En el presente trabajo se estudian el mortero de cal hidráulica y el mortero mixto de cal aérea y cemento Portland, siendo este último el más utilizado en la actualidad, ya que la cal ha pasado a un segundo plano en la construcción debido a los grandes avances en la producción de cemento a lo largo del siglo XX. Estos avances han desplazado a la cal, un material utilizado desde hace milenios, olvidando su alta resistencia al paso del tiempo, cuya prueba es el gran volumen de ...

Family experiences, the motivation for science learning and science ...

African Journals Online (AJOL)

Schulze, Salome

Student Motivation for Science Learning questionnaire combined with items investigating family experiences. The findings .... decisions and formulate behavioural goals for their ..... science achievement, making interpretation diffi- cult and ...

Realce textural mediante "desbaste iónico" de muestras pulidas de clínker de cemento portland para estudios por microscopía electrónica de "scanning"

Directory of Open Access Journals (Sweden)

Rodríguez Rey, Ángel

1985-06-01

Full Text Available Results of using "ion thinning" techniques as final stage in the preparation of polished samples of portland cement clinker for SEM studies are showed. Under proper conditions, flat and clean surfaces are obtained which allow to discriminate textural facts (grain size, form, etc., hardly to see on conventional polished samples due to the similarities of the secondary electron emission of the clinker minerals.

Se estudian los resultados de la aplicación del "desbaste iónico" como etapa final de la preparación de muestras pulidas de clínker de cemento portland para estudios por microscopía electrónica de "scanning". Se observa que, bajo condiciones apropiadas, se obtienen superficies planas y limpias que permiten distinguir rasgos texturales (tamaño, forma y bordes de grano que, dadas las similares características de emisión de electrones secundarios que poseen los minerales del clínker, son de difícil discriminación en secciones pulidas convencionales.

Influence of Ba²⁺ and Sr²⁺ ions on the hydration process of portland cement and blended cements

OpenAIRE

Živanović, B. M.; Petrašinović, Lj.; Milovanović, T.; Karanović, Lj.; Krstanović, I.

1987-01-01

This study concerns the influence of the concentration of Sr2+ and Ba2+ ions in mortar batch waters upon the hydration process of various Portland and additive cements. An increase in the mechanical resistence of said cements is observed, after 28 days, when the concentration of Ba2+ and Sr2+ ions in the mortar batch waters increases. This suggests a possible microstructural explanation of said phenomenon.En el presente trabajo se estudia la influencia de la concentración de los iones Sr2+ y...

78 FR 23255 - Findings of Misconduct in Science/Research Misconduct

Science.gov (United States)

2013-04-18

... research misconduct in research funded by National Institute of General Medical Sciences (NIGMS), National... peptide, and by falsely inserting a band in lane 3 to represent the [alpha]VBS peptide, in Figure 4B of...

A Practitioner’s Guide to Trust and Legitimacy

Science.gov (United States)

2013-09-01

Mary Tomkins, Mikki Honeycutt, and the mentors of 11 45 and Connected—you inspired me and, through your example, made me want to find a way to trust...172 Personal observation for first 20 years of career. 173 Bryan Parman, John Scruggs, and Mary Otto...Fourth Circuit, Graham V. Conner , 1989. 181 Portland Police Bureau, “Portland Police Policy 1010.00, Use of Force,” section 5, in Portland Police

DURABILIDAD DEL CEMENTO PORTLAND BLANCO ADICIONADO CON PIGMENTO AZUL ULTRAMAR

Directory of Open Access Journals (Sweden)

CAROLINA GIRALDO

2010-01-01

Full Text Available El pigmento Azul Ultramar (AU es un aluminosilicato polisulfurado de sodio que reacciona con el aluminato tricálcico (C3A y con el óxido de calcio (CaO del cemento Pórtland blanco en presencia de agua, generando cantidades considerables de etringita a edad temprana y en menor proporción de tobermorita. Esta etringita primaria se presenta en forma de fibras no orientadas mejorando el desempeño mecánico de los morteros, y al mismo tiempo dejando pocas cantidades de C3A disponible para la formación de etringita secundaria. En esta investigación se evalúa la durabilidad a diferentes edades de curado en morteros de cemento Portland blanco sustituidos por 0%, 10% y 20% de AU en peso, mediante pruebas de succión capilar y evaluación del cambio longitudinal de morteros expuestos a una solución de sulfato de sodio con una concentración del 5% (ASTM C1012. Los resultados evidencian una mayor resistencia a compresión y a flexión, una significativa disminución de la expansión y una reducción hasta del 800% de la absorción de agua en morteros con AU. Todo esto debido a la formación de las fases minerales adicionales (etringita primaria y tobermorita, las cuales fueron identificadas mediante microscopía electrónica de barrido (SEM.

PBS Plus Facebook: The Old And New Communication Of Climate Science (Please "Like" And "Share" This Abstract)

Science.gov (United States)

Alley, R. B.; Haines-Stiles, G.; Akuginow, E.

2012-12-01

Traditional and innovative communications strategies were combined in "Earth: The Operators' Manual" (ETOM; writer & director Geoff Haines-Stiles, producer Erna Akuginow, presenter Richard Alley). We attempted both a clear and accessible presentation of some key essentials of current climate science and an experiment in new messaging and new media for outreach and education. ETOM is a 3-part TV series broadcast by PBS ("…one of the more interesting documentary series to come along in years", said the New York Times) and a 320 plus page tradebook, with 110 pages of footnotes referencing peer-reviewed science, published by Norton. But it's also a lively and growing Facebook page with a clear voice sharing positive examples of how renewable energy can reduce polluting emissions here in the US and worldwide, alongside headlines of climate science, and a website—relaunched for the 2012 Earth Day PBS broadcasts—where all three programs can be streamed, and teachers can register to download HD segments for classroom use. The TV programs were designed to offer a highly accessible statement of core climate science, literally explaining how ice cores show us today's climate is changing in ways not seen in the last 800,000 thousand years and why physics and chemistry let us know "It's Us" who are changing CO2 levels in the atmosphere through burning fossil fuels. But the project's outreach components also includes a "Science Pub" in a converted theater in Portland, where the audience consumes food, drink and climate science, and "Adventures of a Climate Scientist in the Age of Politics and Punditry," a dynamic live performance recorded for TV and the web. Messaging includes a Navy Rear Admiral in dress whites explaining why the Pentagon believes climate change is real, and scenes showing Marines and Army implementing solar technologies to enhance mission security and reduce their carbon bootprint. Similarly, outreach events at the North Carolina Museum of Natural

Evaluation of Portland cement from X-ray diffraction associated with cluster analysis; Avaliacao de cimento Portland a partir da difracao de raios X associada a analise por agrupamento

Energy Technology Data Exchange (ETDEWEB)

Gobbo, Luciano de Andrade, E-mail: luciano.gobbo@panalytical.com [Panalytical Brasil, Sao Paulo, SP (Brazil); Montanheiro, Tarcisio Jose, E-mail: tarcisio.montanheiro@gmail.com [Instituto Geologico, Secretaria de Estado do Meio Ambiente, Sao Paulo, SP (Brazil); Montanheiro, Filipe, E-mail: flpmontanheiro@gmail.com [Universidade Estadual Paulista (LEBAC/UNESP), Rio Claro, SP (Brazil). Departamento de Geologia Aplicada. Lab. de Estudos de Bacias; Sant' Agostino, Lilia Mascarenhas, E-mail: agostino@usp.br [Universidade de Sao Paulo (USP), SP (Brazil). Instituto de Geociencias. Departamento de Geologia Sedimentar e Ambiental

2013-12-15

The Brazilian cement industry produced 64 million tons of cement in 2012, with noteworthy contribution of CP-II (slag), CP-III (blast furnace) and CP-IV (pozzolanic) cements. The industrial pole comprises about 80 factories that utilize raw materials of different origins and chemical compositions that require enhanced analytical technologies to optimize production in order to gain space in the growing consumer market in Brazil. This paper assesses the sensitivity of mineralogical analysis by X-ray diffraction associated with cluster analysis to distinguish different kinds of cements with different additions. This technique can be applied, for example, in the prospection of different types of limestone (calcitic, dolomitic and siliceous) as well as in the qualification of different clinkers. The cluster analysis does not require any specific knowledge of the mineralogical composition of the diffractograms to be clustered; rather, it is based on their similarity. The materials tested for addition have different origins: fly ashes from different power stations from South Brazil and slag from different steel plants in the Southeast. Cement with different additions of limestone and white Portland cement were also used. The Rietveld method of qualitative and quantitative analysis was used for measuring the results generated by the cluster analysis technique. (author)

Sadhana | Indian Academy of Sciences

Indian Academy of Sciences (India)

Three concrete mixes namely ordinary Portland cement (OPC) concrete i.e. concrete with 100% OPC as control, and concrete with 30% and 60% POFA having different water/binder (w/b) ratios of 0.4, 0.45 and 0.5 were prepared. Filling ability, passing ability and segregation resistance of SCC along with strength properties ...

Secondary Science Teachers' and Students' Involvement in a Primary School Community of Science Practice: How It Changed Their Practices and Interest in Science

Science.gov (United States)

Forbes, Anne; Skamp, Keith

2016-02-01

MyScience is a primary science education initiative in which being in a community of practice is integral to the learning process. In this initiative, stakeholder groups—primary teachers, primary students and mentors—interact around the `domain' of `investigating scientifically'. This paper builds on three earlier publications and interprets the findings of the views of four secondary science teachers and five year 9 secondary science students who were first-timer participants—as mentors—in MyScience. Perceptions of these mentors' interactions with primary students were analysed using attributes associated with both `communities of practice' and the `nature of science'. Findings reveal that participation in MyScience changed secondary science teachers' views and practices about how to approach the teaching of science in secondary school and fostered primary-secondary links. Year 9 students positively changed their views about secondary school science and confidence in science through participation as mentors. Implications for secondary science teaching and learning through participation in primary school community of science practice settings are discussed.

Use of copper slag in the manufacture of Portland cement

Directory of Open Access Journals (Sweden)

Aquilar Elguézabal, A.

2006-03-01

Full Text Available Given its chemical and mineralogical characteristics, copper slag, a solid industrial by-product, may serve as a partial substitute for silica and hematite in raw mixes used to manufacture Portland cement clinker. The benefits of such substitution include lower production costs and energy savings. The effect of slag-containing raw mixes on the reactivity of the CaO-Si02-Al203-Fe203 system was studied at three temperatures (1,350, 1,400 and 1,450ºC. Four mixes were used: M-1 and M-2 prepared with conventional prime materials and M-3 and M-4, in which ignimbrite and hematite were substituted for slag. In M-3 the slag replaced 45.54% of the ignimbrite and 100% of the hematite, and in M-4 100% of the mineral iron. The samples were clinkerized at 1,350, 1,400 and 1,450ºC. At 1,400ºC, clinker M-3 was found to have 10.7% less free lime than M-1, while the level in M-4 it was 15.93% lower than in M-2. The presence of the main clinker phases was confirmed by X-ray diffraction, which also showed that adding slag during c/inker manufacture slightly improves raw mix burnability without generating new unwanted phases. Consequently, recovery in cement kilns would appear to be an economically and environmentally feasible alternative to coprocessing such waste, although the industrial use of slag depends on its heavy metal content.En acuerdo con las características químicas y mineralógicas de la escoria de cobre, este residuo sólido industrial puede ser utilizado en el proceso de fabricación de clínker Portland como sustituto parcial de los minerales de sílice y hematita en la formación de mezclas crudas cuyos beneficios serían: disminución de los costos de producción de mezclas crudas y del consumo calorífico. El efecto de la adición de la escoria en las mezclas crudas sobre la reactividad del sistema CaO-Si02-Al203-Fe20 3 se estudió en tres niveles de temperatura (1.350, 1.400 Y 1.450ºC. Se trabajó con cuatro mezclas crudas, M-1 y M

Impact of chloride on the mineralogy of hydrated Portland cement systems

International Nuclear Information System (INIS)

Balonis, Magdalena; Lothenbach, Barbara; Le Saout, Gwenn; Glasser, Fredrik P.

2010-01-01

Chloride ion is in part bound into ordinary Portland cement paste and modifies its mineralogy. To understand this a literature review of its impacts has been made and new experimental data were obtained. Phase pure preparations of Friedel's salt, Ca 4 Al 2 (Cl) 1.95 (OH) 12.05 .4H 2 O, and Kuzel's salt, Ca 4 Al 2 (Cl)(SO 4 ) 0.5 (OH) 12 .6H 2 O, were synthesized and their solubilities were measured at 5, 25, 55 and 85 o C. After equilibration, solid phases were analysed by X-ray diffraction while the aqueous solutions were analysed by atomic absorption spectroscopy and ion chromatography. The solid solutions and interactions of Friedel's salt with other AFm phases were determined at 25 o C experimentally and by calculations. In hydrated cements, anion sites in AFm are potentially occupied by OH, SO 4 and CO 3 ions whereas Cl may be introduced under service conditions. Chloride readily displaces hydroxide, sulfate and carbonate in the AFm structures. A comprehensive picture of phase relations of AFm phases and their binding capacity for chloride is provided for pH ∼ 12 and 25 o C. The role of chloride in AFt formation and its relevance to corrosion of embedded steel are discussed in terms of calculated aqueous [Cl - ]/[OH - ] molar ratios.

Summary of Research: Academic Departments 1990-1991

Science.gov (United States)

1991-10-01

of Systems Sciences, Portland, Oregon, 9 July 1990. CULHAM, Phyllis, Professor, " Plutarch on the Siege of Syracusc: The Primacy of Science over...ARTIGIANI, P. Robert, Professor, "Social Change: Technology," International Plutarch Society, Insights and Implications from Contemporary University of

Parents' Attitudes Towards Science and their Children's Science Achievement

Science.gov (United States)

Perera, Liyanage Devangi H.

2014-12-01

Although countries worldwide are emphasizing the importance of science education for technological development and global economic competition, comparative findings from standardized international student assessments reveal a huge gap in science scores between developed and developing countries. Certain developed economies too have made little progress in raising science achievement over the past decade. Despite school improvement being placed high on the policy agenda, the results of such actions have been poor. Therefore, there is a need to explore additional ways in which science achievement can be enhanced. This study focuses on the family and examines whether parents' attitudes towards science (how much they value science and the importance they place on it) can influence their children's science achievement. Individual- and school-level data are obtained from the Program for International Student Assessment 2006 survey for 15 Organisation for Economic Co-operation and Development (OECD) and non-OECD countries. Hierarchical linear modelling is employed to estimate the equations. The findings indicate that parents' attitudes towards science have a positive and statistically significant effect on science achievement, after controlling for other important student- and school-level variables. Moreover, students from poor backgrounds appear to benefit from more positive parental science attitudes as much as students from high socioeconomic status, such that equality of student achievement is not affected. This study recommends that schools and teachers encourage parents to play a more pro-active role in their children's science education, as well as educate parents about the importance of science and strategies that can be adopted to support their children's science learning.

Performance of constructed evaporation ponds for disposal of smelter waste water: a case study at Portland Aluminum, Victoria, Australia.

Science.gov (United States)

Salzman, S A; Allinson, G; Stagnitti, F; Coates, M; Hill, R J

2001-06-01

The construction of evaporative ponds and wetlands for the disposal of waste water high in ionic concentrations is a waste disposal strategy currently considered by many industries. However, the design, construction and management of these ponds and wetlands are not straightforward as complex chemical interactions result in both spatial and temporal changes in water quality. The effects of evaporation and drainage on the water quality in two constructed ponds, an adjacent man-made wetland and local groundwater at Portland Aluminium were investigated. The minimum volume of water entering the ponds during the study period was 0.96 +/- 0.16 ML per month. The predicted theoretical evaporative capacity of the two ponds was calculated to be 0.30 +/- 0.07 ML per month. More water enters the ponds than it is theoretically possible to evaporate under the ambient weather conditions at Portland, yet the ponds do not overflow, suggesting percolation through the pond lining. No spatial differences in solute concentrations (fluoride, sulphate, bicarbonate, carbonate, sodium, potassium, calcium, and magnesium ions) were found within the waters of either pond, although temporal differences were apparent. The results support the conclusion that the ponds are not impermeable, and that much of the waste water entering the ponds is being lost through seepage. The impacts on local groundwater chemistry of this seepage are addressed. Significant correlations exist between solute presence within and between the ponds. wetland and groundwater. Fluoride and sulphate concentrations were significantly higher in pond waters throughout the duration of the experiment. Pond sediments revealed a high degree of spatial and temporal heterogeneity in the concentration of all monitored ions resulting from the chemical heterogeneity of the material making up the pond linings. Adsorption isotherms for fluoride indicate that the adsorption capacity of the pond linings remains high for this ion

Evaluation of the physical properties of an endodontic Portland cement incorporating alternative radiopacifiers used as root-end filling material.

Science.gov (United States)

Camilleri, J

2010-03-01

To investigate the physical and chemical properties of Portland cement (PC) loaded with alternative radiopacifying materials for use as root-end filling materials in a mineral trioxide aggregate (MTA)-like system. Portland cement loaded with barium sulphate, gold and silver/tin alloy was mixed with water, and the physical and chemical properties of the hydrated cements were evaluated. MTA and intermediate restorative material (IRM) were used as controls. The radiopacity was compared to the equivalent thickness of aluminium, and the setting time of the cements was assessed using an indentation technique. The compressive strength and the stress-strain relationship were determined at 28 days. The stress-strain relationship was determined by monitoring the strain generated when the cement was subjected to compressive load. In addition, the pH was determined in water and simulated body fluid for a period of 28 days. The radiopacity of the cements using alternative radiopacifiers was comparable to MTA (P > 0.05). IRM demonstrated a higher radiopacity than all the materials tested (P cements with the exception of IRM exhibited an alkaline pH and had an extended setting time when compared to IRM. MTA had a longer setting time than the PC (P cement (P = 0.159). The addition of a radiopacifier retarded the setting time (P cements had comparable strength to PC (P > 0.05). IRM was the weakest cement tested (P cement loaded with gold radiopacifier had comparable strength to MTA (P = 1). The stress-strain relationship was linear for all the cements with IRM generating more strain on loading. Within the parameters set in this study, bismuth oxide in MTA can be replaced by gold or silver/tin alloy. The physical, mechanical and chemical properties of the cement replaced with alternative radiopacifiers were similar and comparable to ProRoot MTA.

Moessbauer and calorimetric studies of portland cement hydration in the presence of black gram pulse

International Nuclear Information System (INIS)

Rai, Sarita; Kurian, Sajith; Dwivedi, V. N.; Das, S. S.; Singh, N. B.; Gajbhiye, N. S.

2009-01-01

Effect of different concentrations of naturally occurring admixture in the form of fine powder of black gram pulse (BGP) on the hydration of Portland cement was studied by isothermal calorimetry and 57 Fe Moessbauer spectroscopy. The spectra were recorded for anhydrous cement and the hydration products at room temperature and 77 K. In the presence of BGP, the spectra showed superparamagnetic doublets at room temperature and the sextet at 77 K, due to the presence of fine particles of iron containing component. Moessbauer studies of hydration products confirmed the formation of nanosize hydration products containing Fe 3+ . The isomer shift (δ) and the quadrupole splitting (ΔE Q ) values of C 4 AF in the cement confirmed iron in an octahedral and tetrahedral environment with +3 oxidation state. The high value of quadrupole splitting showed the high asymmetry of the electron environment around the iron atom. The overall mechanism of the hydration of cement in presence of BGP is discussed.

Evaluation of Portland cement from X-ray diffraction associated with cluster analysis

International Nuclear Information System (INIS)

Gobbo, Luciano de Andrade; Montanheiro, Tarcisio Jose; Montanheiro, Filipe; Sant'Agostino, Lilia Mascarenhas

2013-01-01

The Brazilian cement industry produced 64 million tons of cement in 2012, with noteworthy contribution of CP-II (slag), CP-III (blast furnace) and CP-IV (pozzolanic) cements. The industrial pole comprises about 80 factories that utilize raw materials of different origins and chemical compositions that require enhanced analytical technologies to optimize production in order to gain space in the growing consumer market in Brazil. This paper assesses the sensitivity of mineralogical analysis by X-ray diffraction associated with cluster analysis to distinguish different kinds of cements with different additions. This technique can be applied, for example, in the prospection of different types of limestone (calcitic, dolomitic and siliceous) as well as in the qualification of different clinkers. The cluster analysis does not require any specific knowledge of the mineralogical composition of the diffractograms to be clustered; rather, it is based on their similarity. The materials tested for addition have different origins: fly ashes from different power stations from South Brazil and slag from different steel plants in the Southeast. Cement with different additions of limestone and white Portland cement were also used. The Rietveld method of qualitative and quantitative analysis was used for measuring the results generated by the cluster analysis technique. (author)

Analysis of metal contents in Portland Type V and MTA-based cements.

Science.gov (United States)

Dorileo, Maura Cristiane Gonçales Orçati; Bandeca, Matheus Coelho; Pedro, Fábio Luis Miranda; Volpato, Luiz Evaristo Ricci; Guedes, Orlando Aguirre; Dalla Villa, Ricardo; Tonetto, Mateus Rodrigues; Borges, Alvaro Henrique

2014-01-01

The aim of this study was to determine, by Atomic Absorption Spectrometry (AAS), the concentration levels of 11 metals in Type V gray and structural white PC, ProRoot MTA, and MTA Bio. Samples, containing one gram of each tested cement, were prepared and transferred to a 100 mL Teflon tube with a mixture of 7.0 mL of nitric acid and 21 mL of hydrochloric acid. After the reaction, the mixture was filtered and then volumed to 50 mL of distilled water. For each metal, specific patterns were determined from universal standards. Arsenic quantification was performed by hydride generator. The analysis was performed five times and the data were statistically analyzed at 5% level of significance. Only the cadmium presented concentration levels of values lower than the quantification limit of the device. The AAS analysis showed increased levels of calcium, nickel, and zinc in structural white PC. Type V PC presented the greatest concentration levels of arsenic, chromium, copper, iron, lead, and manganese (P cements, and the lowest concentration levels were observed in Portland cements, while the highest were observed in ProRoot MTA. Both PC and MTA-based cements showed evidence of metals inclusion.

Plans and Living Practices for the Green Campus of Portland State University

Directory of Open Access Journals (Sweden)

Yoon Jung Choi

2017-02-01

Full Text Available This study aims to comprehend Portland State University (PSU’s green campus strategies, and students’ level of knowledge and living practices relating to green campus. PSU’s sustainable campus plan has been nationally and internationally recognized. A literature review, field investigation, and interviews were conducted to ascertain the PSU green campus strategies. This study also used a survey to understand students’ level of knowledge and practices. The survey results were analyzed by SPSS. Green campus projects at PSU were operated by official organizations and funded according to PSU’s long term plans in 12 multilateral categories: administration, energy, water, climate action, green buildings, green purchasing, waste reduction and recycling, food and dining services, transportation, land use, action, and education and student activity. The survey results show that the level of students’ understanding about PSU’s green campus strategies was somewhat low, but the amount of practice of a sustainable lifestyle was higher. Students who had taken courses related with sustainability or were engaged in sustainable activities had more knowledge about green campus strategies than students who had not. Therefore, it would be important to focus more on educating students and developing related programs in order to have more positive effects of green campus projects.

Information Literacy in Science Writing: How Students Find, Identify, and Use Scientific Literature

Science.gov (United States)

Klucevsek, Kristin M.; Brungard, Allison B.

2016-01-01

For undergraduate students to achieve science literacy, they must first develop information literacy skils. These skills align with Information Literacy Standards and include determining appropriate databases, distinguishing among resource types, and citing resources ethically. To effectively improve information literacy and science literacy, we…

Some aspects about the Portland cement utilization as a matrix for radioactive waste immobilization

International Nuclear Information System (INIS)

Giraldelli, M.A.

1990-01-01

More recently, the environmental policy has concentrated the focus on the study of the waste disposal environmental impact. Since Portland cement is commonly used as a matrix in the low-and intermediate-level radioactive waste immobilization, in the present work, some relationships between the structure and properties of matrix, based on available concrete technology information, has been established by using the multi-level approach analysis. The relationships were developed based on hydrating reactions, the microstructure models, the pore system. It have been verified that: a) CSH gel is responsible for the cementing action and for the strength; b) it seems that the capillary porosity is the strength limiting; c) the permeability, regarded in terms of gel porosity and reduced capillary porosity of the hardened cement paste, may not be a decisive factor for the radionuclide release; d) the shrinkage and the swelling induced cracks can enhance the diffusion mechanism for the cracks increase the exposed surface. The durability of the waste disposal matrix concerning chemical attack in the acidic environment has been considered. (author)

Influence of the waste glass in the axial compressive strength of Portland cement concrete

International Nuclear Information System (INIS)

Miranda Junior, E.J.P.; Paiva, A.E.M.

2012-01-01

In this work, was studied the influence of the incorporation of waste glass, coming from the stage of thinning and polishing of a company of thermal glass treatments, in the axial compressive strength of Portland cement concrete. The coarse and ground aggregates used was crushed stone and sand, respectively. For production of the concrete, percentages of glass residues of 5%, 10% and 20% had been used in substitution to the sand, and relations water/cement (a/c) 0,50, 0,55 and 0,58. The cure of the test bodies was carried through in 7, 14 and 28 days. The statistics analysis of the results was carried out through of the analysis of variance for each one of the cure times. From the results of the compressive strength of the concrete, it could be observed that the concrete has structural application for the relation a/c 0,5, independently of waste glass percentage used, and for the relation a/c 0,55 with 20% of waste glass. (author)

Study on Characteristics of Lightweight Aggregate Concrete Made From Foam and Ordinary Portland Cement

Directory of Open Access Journals (Sweden)

Ibrahim N.M.

2016-01-01

Full Text Available The production and characteristic of lightweight bubble aggregates (LBA are presented in this paper. The LBA are produced by mixing between the foam and ordinary Portland cement according to the composition which has been set. Then, the characteristics of LBA such as density, water absorption, specific gravity, compressive strength, aggregate impact value and microscopic analysis of the LBA are analyzed. Those characteristics are identified in order to ensure that the LBA are successfully categorized into lightweight aggregate. The loose bulk density is obtained at 812.5 kg/m3 which can be categorized under lightweight aggregate group. For water absorption the value obtained is 9.7 % which is slightly higher compared to normal aggregate. Meanwhile the average specific gravity obtained for the samples of LBAis 1.75. Compressive strength for the aggregates was 17.76 MPa. The highest compressive strength for LBA foamed concrete was obtained at 25% replacement with 7.83MPa. Thus, the LBA have a significant features and characteristics that can be used as coarse aggregates in concrete.

Individuals with greater science literacy and education have more polarized beliefs on controversial science topics.

Science.gov (United States)

Drummond, Caitlin; Fischhoff, Baruch

2017-09-05

Although Americans generally hold science in high regard and respect its findings, for some contested issues, such as the existence of anthropogenic climate change, public opinion is polarized along religious and political lines. We ask whether individuals with more general education and greater science knowledge, measured in terms of science education and science literacy, display more (or less) polarized beliefs on several such issues. We report secondary analyses of a nationally representative dataset (the General Social Survey), examining the predictors of beliefs regarding six potentially controversial issues. We find that beliefs are correlated with both political and religious identity for stem cell research, the Big Bang, and human evolution, and with political identity alone on climate change. Individuals with greater education, science education, and science literacy display more polarized beliefs on these issues. We find little evidence of political or religious polarization regarding nanotechnology and genetically modified foods. On all six topics, people who trust the scientific enterprise more are also more likely to accept its findings. We discuss the causal mechanisms that might underlie the correlation between education and identity-based polarization.

Motivating Students with Authentic Science Experiences: Changes in Motivation for School Science

Science.gov (United States)

Hellgren, Jenny M.; Lindberg, Stina

2017-01-01

Background: Students' motivation for science declines over the early teenage years, and students often find school science difficult and irrelevant to their everyday lives. This paper asks whether creating opportunities to connect school science to authentic science can have positive effects on student motivation. Purpose: To understand how…

Modeling of Hydration, Compressive Strength, and Carbonation of Portland-Limestone Cement (PLC Concrete

Directory of Open Access Journals (Sweden)

Xiao-Yong Wang

2017-01-01

Full Text Available Limestone is widely used in the construction industry to produce Portland limestone cement (PLC concrete. Systematic evaluations of hydration kinetics, compressive strength development, and carbonation resistance are crucial for the rational use of limestone. This study presents a hydration-based model for evaluating the influences of limestone on the strength and carbonation of concrete. First, the hydration model analyzes the dilution effect and the nucleation effect of limestone during the hydration of cement. The degree of cement hydration is calculated by considering concrete mixing proportions, binder properties, and curing conditions. Second, by using the gel–space ratio, the compressive strength of PLC concrete is evaluated. The interactions among water-to-binder ratio, limestone replacement ratio, and strength development are highlighted. Third, the carbonate material contents and porosity are calculated from the hydration model and are used as input parameters for the carbonation model. By considering concrete microstructures and environmental conditions, the carbon dioxide diffusivity and carbonation depth of PLC concrete are evaluated. The proposed model has been determined to be valid for concrete with various water-to-binder ratios, limestone contents, and curing periods.

ESTUDIO SOBRE PASTAS Y MORTEROS DE CEMENTO PORTLAND CON REEMPLAZO POR LOZA SANITARIA

Directory of Open Access Journals (Sweden)

Silvina Zito

2016-01-01

Full Text Available En este trabajo se analiza el uso de Loza Sanitaria como reemplazo del cemento portland. Los reemplazos utilizados fueron 8, 24 y 40 % en peso; los ensayos empleados contemplaron la evolución de la hidratación desde los primeros minutos (hasta 48 horas a través de la calori metría , y a partir de los dos días (hasta 28 días por medio de la velocidad de fijación del hidróxido de calcio, el agua químicamente combinada, la resistencia mecánica a flexión y a compresión y la porosidad. Los resultados mostraron que a medida que aum enta el porcentaje de reemplazo, a las primeras edades d el efecto de dilución solapa y se contrapone con el de estimulación física ; y a la edad de 28 días todas las mezclas presentan además de la estimulación física también la química , por la reactividad puzolánica.